diff --git a/PCB/v2.x/GPIO_table.md b/PCB/v2.x/GPIO_table.md index 490dd14..dbf8132 100644 --- a/PCB/v2.x/GPIO_table.md +++ b/PCB/v2.x/GPIO_table.md @@ -1,60 +1,94 @@ -# Snips Controller V2 — BT840XE pin table +# Snips Controller V2 — ESP32-S3-MINI-1U pin table > The wiring source is `PCB/v2.x/stackup/board.kdl`, and the module is modeled in -> `PCB/v2.x/stackup/parts.kdl`. Pin data is from Fanstel's BT840X/BT840XE Product -> Specifications Ver 1.26, in `datasheets/`. The module is on the bottom side. +> `PCB/v2.x/stackup/parts.kdl`. Pin data is from Espressif's ESP32-S3-MINI-1 & MINI-1U datasheet +> v1.7, in `datasheets/`. The module is on the top side. -The Fanstel BT840XE (nRF52840-QIAA, SKY66112 PA, u.FL) runs the firmware and the Zigbee link. -It replaces the ESP32 and XBee used on V1.x. +The ESP32-S3-MINI-1U-N8 runs the firmware. The XBee 3 is optional: it sits on a castellated daughter board on the underside, and the ESP32's own Bluetooth and ESP-NOW work without it. + +Pins are chosen by position, not carried over from V1, so V2 needs its own firmware pin map. The module is turned 270 degrees so its pins face what they connect to: + +| Module side on the board | Pins | Faces | +|---|---|---| +| Top edge, left to right | IO11 ... IO0, 3V3, GND | Macro buttons, stick, trigger | +| Left edge, top to bottom | IO12 ... IO18, USB, IO21 ... IO48 | OLED connector, USB route, charger, lower-left parts | +| Bottom edge, left to right | IO35 ... IO42, TXD0, RXD0, IO45, GND, IO46, EN | XBee pad row toward USB | +| Right edge | GND only | Nothing needs it, so the side strip stays free | ## Module rules -- **Power:** VDD and VDDH are both tied to 3V3_RF, the 3.3 V rail after FB_RF1. The hall sensor and stick also use 3V3_RF, so their ratiometric outputs track the ADC's VDD reference. Sample them with the SAADC's VDD/4 reference. Fanstel Note 1 requires - a regulated 3.3 V, 300 mA minimum, on VDD; VDDH alone cannot power the PA. DCCH stays open. -- **Reserved:** P0.06, P0.08, P0.17 and P0.19 control the PA and are not connected at the pads. - P0.00 and P0.01 go to the module's 32.768 kHz crystal. -- **Pads:** castellated pins 1-16 are the only hand-solderable ones. All others are LGA. +- **Variant:** use the -N8. +- **Straps:** IO0 is pulled up by R_BOOT_PU1. IO3, IO45 and IO46 are unconnected, so nothing can disturb the boot mode or flash voltage. +- **ADC:** analog inputs stay on ADC1 (IO1-IO10), since ADC2 is not usable while the Wi-Fi radio runs, which ESP-NOW needs. +- **PWR_HOLD stays on RXD0 (IO44).** Its weak pull-up stays on at and after reset (ESP32-S3 datasheet Table 2-1), so a reset holds the latch and reboots the board. On a pin with no pull, a reset would drop the latch and turn the board off. V1 hardware has verified this pin. +- **Power button sense stays on an RTC-domain pin.** With the board off, VSYS lifts this node through R_INV_BASE1 and D_INV_ISO1. V1 verified that on a VDD3P3_RTC pin; IO33-IO37 are in the VDD_SPI domain (Table 2-1). +- **TXD0 (IO43)** prints the boot log, so it stays free for debugging. RGB data has moved off it, so the LED no longer sees that traffic. +- **Boot glitches:** the low-level power-up glitches on IO1-IO17 (Table 2-2, where IO15 and IO16 appear as XTAL_32K) are 60 µs. Those pins carry only inputs, except IO1 (SLEEP_RQ, where low means awake). XBee RESET is on IO42, which has no listed glitch. +- **IO26 stays unconnected.** It is the PSRAM chip-select, and Arduino runs a PSRAM probe at every boot, so it is driven before `setup()`. The probe fails on the -N8, which has no PSRAM, and boot continues. +- **Do not flash V1 firmware on V2.** It would drive IO42 low, which is XBee RESET here, and treat other V2 pins as SPI. V2 needs its own pin map. +- **EN:** 10 kΩ and 1 µF, as Espressif advises (Peripheral Schematics), so EN crosses 0.75 × VDD about 14 ms after the rail is up. V1 has no capacitor. +- **Pad 61:** the thermal pad is 9 segments, soldered to GND. ## Pin assignments -| Function | nRF52840 | Module pad | Notes | +| Function | GPIO | Module pin | Notes | +|---|---|---|---| +| Boot button | IO0 | 4 | R_BOOT_PU1 pull-up | +| XBee SLEEP_RQ (DTR) | IO1 | 5 | Directly over carrier pad 7. Drive it low as one of the first instructions in `setup()` | +| Macro 6 | IO2 | 6 | Direct, active low, internal pull-up | +| Macro 3 | IO4 | 8 | Direct, active low, internal pull-up | +| Macro 2 | IO5 | 9 | Direct, active low, internal pull-up | +| Stick Y | IO6 (ADC1_CH5) | 10 | Analog | +| Stick X | IO7 (ADC1_CH6) | 11 | Analog | +| Macro 5 | IO8 | 12 | Direct, active low, internal pull-up | +| Analog trigger | IO9 (ADC1_CH8) | 13 | DRV5055 through R_TRIG1 and C_TRIG1, about 1.6 kHz low-pass. C_TRIG1 sits beside the pin | +| VSYS sense | IO10 (ADC1_CH9) | 14 | Divide-by-3 from VSYS. The divider sits beside the pin | +| Macro 4 | IO11 | 15 | Direct, active low, internal pull-up | +| I2C SDA | IO12 | 16 | OLED, IMU. R_I2C_SDA1 4.7k fitted. Top of the left edge, so SDA and SCL do not cross at the connector | +| I2C SCL | IO13 | 17 | R_I2C_SCL1 4.7k fitted | +| Charger STAT2 | IO14 | 18 | Open drain, pulled up | +| Charger STAT1 | IO15 | 19 | Open drain, pulled up | +| Macro 1 | IO16 | 20 | Direct, active low, internal pull-up | +| Thumbstick click | IO17 | 21 | Direct, active low, internal pull-up | +| Trigger down | IO18 | 22 | Direct, active low, internal pull-up | +| USB D- / D+ | IO19 / IO20 | 23 / 24 | Native USB, through R_USB_DM1 and R_USB_DP1 27 Ω | +| Power button sense | IO21 | 25 | RTC-domain pin, like V1's IO2 | +| Digital trigger (bumper) | IO47 | 27 | Direct, active low, internal pull-up | +| Trigger up | IO33 | 28 | Direct, active low, internal pull-up | +| XBee CTS | IO34 | 29 | Carrier pad 1 | +| RGB LED data | IO48 | 30 | SK6812 through R_RGB1 | +| XBee DIN | IO35 | 31 | Carrier pad 2. ESP32 transmits here | +| XBee DOUT | IO36 | 32 | Carrier pad 3. ESP32 receives here | +| IMU interrupt | IO37 | 33 | ICM-42670-P INT1. No longer on a strap pin | +| Vol up | IO38 | 34 | Direct, active low, internal pull-up | +| XBee RTS | IO39 | 35 | Carrier pad 4 | +| Vol down | IO40 | 36 | Direct, active low, internal pull-up | +| XBee ON/SLEEP | IO41 | 37 | Carrier pad 5 | +| XBee RESET | IO42 | 38 | Carrier pad 6. Drive open drain only: low or released. The pull-up is on the carrier | +| Power hold (PWR_HOLD) | RXD0 (IO44) | 40 | Must go high early in boot | +| Reset | EN | 45 | R_EN_PU1 and C_EN1 only, no button | + +Antenna: the module's connector is the W.FL/MHF III size, not standard U.FL. The XBee on the carrier has its own U.FL, so each radio has a separate antenna. + +## XBee carrier pads + +U_XBEE1 is 12 pads on the bottom side, 2.54 mm pitch, for a 22 x 17 mm castellated board. The chamfered corner sits by MH3. Pads 1-6 are the row toward USB, left to right seen from the top side; pads 7-12 are the row toward the stick, right to left. + +| Pad | Signal | Pad | Signal | |---|---|---|---| -| I2C SDA | P0.26 | 1 | OLED, IMU. R_I2C_SDA1 4.7k fitted | -| I2C SCL | P0.27 | 2 | R_I2C_SCL1 4.7k fitted | -| Stick X | P0.02 (AIN0) | 5 | Analog | -| Stick Y | P0.03 (AIN1) | 6 | Analog | -| Analog trigger | P0.04 (AIN2) | A3 | DRV5055 through R_TRIG1 and C_TRIG1, about 1.6 kHz low-pass | -| VSYS sense | P0.05 (AIN3) | A4 | Divide-by-3 from VSYS | -| Digital trigger (bumper) | P1.04 | C6 | Direct, active low, internal pull-up | -| Macro 1 | P1.10 | Z5 | Direct, active low, internal pull-up | -| Macro 2 | P0.07 | A5 | Direct, active low, internal pull-up | -| Macro 3 | P1.09 | E3 | Direct, active low, internal pull-up | -| Macro 4 | P1.11 | Z0 | Direct, active low, internal pull-up | -| Macro 5 | P1.07 | E0 | Direct, active low, internal pull-up | -| Macro 6 | P0.20 | E1 | Direct, active low, internal pull-up | -| Thumbstick click | P1.03 | B6 | Direct, active low, internal pull-up | -| Trigger down | P1.06 | Z6 | Direct, active low, internal pull-up | -| Trigger up | P1.08 | A6 | Direct, active low, internal pull-up | -| Vol down | P0.12 | E6 | Direct, active low, internal pull-up | -| Vol up | P1.05 | D6 | Direct, active low, internal pull-up | -| IMU interrupt | P1.12 | Z1 | ICM-42670-P INT1 | -| Power hold (PWR_HOLD) | P1.13 | Z2 | Must go high early in boot | -| Charger STAT1 | P1.14 | Z3 | Open drain, pulled up | -| Charger STAT2 | P1.15 | Z4 | Open drain, pulled up | -| Power button sense | P0.11 | 11 | Direct, so power-off does not depend on I2C | -| Boot button | P1.00 | 12 | R_BOOT_PU1 pull-up | -| RGB LED data | P0.13 | 13 | SK6812, needs a fast pin | -| USB D+ / D- | D+ / D- | E4 / E5 | Native USB | -| USB VBUS | VBUS | F6 | | -| Reset | P0.18 | 14 | J_SWD1 pin 3, SW_RST1 | -| SWD | SWDIO / SWDCLK | 16 / 15 | J_SWD1 pins 2 and 4. First programming | - -Antenna: one u.FL on the module. +| 1 | CTS | 7 | SLEEP_RQ | +| 2 | DIN | 8 | GND | +| 3 | DOUT | 9 | 3V3 | +| 4 | RTS | 10 | 3V3 | +| 5 | ON/SLEEP | 11 | GND | +| 6 | RESET | 12 | GND | + +With no carrier fitted these lines float, so firmware should enable pulls on IO34, IO36 and IO41 and treat a failed XBee AT query as "no XBee". ## Buttons -Every button wires straight to a module GPIO and to GND, using the internal pull-ups, so simultaneous presses need no diodes. The pins are on the outer LGA ring, matched to the nearest button. +Every button wires straight to a module GPIO and to GND, using the internal pull-ups, so simultaneous presses need no diodes. ## Addresses OLED 0x3C, ICM-42670-P 0x68. R_I2C_SDA1 and R_I2C_SCL1 stay on the board so the IMU works with no OLED attached. ## Free pins -The module still has plenty of LGA GPIOs free. P0.09 and P0.10 are NFC pins by default. AIN4-7 (P0.28-31) are free analog inputs. +TXD0 (IO43) is free. Leave IO26 unconnected (see Module rules). IO3, IO45 and IO46 are straps, so leave them unconnected. diff --git a/PCB/v2.x/README.md b/PCB/v2.x/README.md index dc67a56..812f44d 100644 --- a/PCB/v2.x/README.md +++ b/PCB/v2.x/README.md @@ -9,18 +9,19 @@ through `snips_controller.stackup_sch`; sync it with the Stackup KiCad plugin. R ## V2 board -70 x 30 mm, 4 layers: F.Cu signals, In1 signals with a partial 3V3 fill, In2 solid GND, B.Cu signals. Routed, not yet fabricated. - -- **One module:** the BT840XE replaces the ESP32 and XBee, which could not sit back to back. Espressif requires a single reflow, and Digi forbids reflowing the XBee upside down. -- **Reflow:** Fanstel allows at most 2 cycles and no opposite-side reflow, so the bottom side, which carries the module, must be the last pass. It is MSL 3 per JLC's listing. -- **Radio link:** Amidala's droids use XBee Zigbee 3.0, so the controller must join that network. That Zigbee firmware is still to be written. -- **First programming:** SWD, through J_SWD1, a TC2030-NL Tag-Connect footprint on the bottom with no part fitted; use a TC2030-CTX-NL cable. New modules hold Fanstel's AT firmware, so USB only works once a bootloader is loaded. The latch only stays on through the power button or `PWR_HOLD`, not USB, so hold the power button while flashing a new board. -- **Bootloader entry:** hold SW_BOOT1 (P1.00) while pressing the power button. The bootloader must drive `PWR_HOLD` high straight away. SW_RST1, on the bottom, resets the module. That releases `PWR_HOLD`, so it forces the board off when firmware hangs, which the power button cannot do; a quick tap may only restart it. The bootloader must enable the reset pin. Use the BT840XE, not the -p part, which has access port protection on. -- **Power:** VDD and VDDH are tied together after FB_RF1 and C_RF_BULK1, per Fanstel's Note 1 and supply design note. +70 x 30 mm, 4 layers: F.Cu signals, In1 solid 3V3, In2 solid GND, B.Cu signals. 1.6 mm thick. Routed, not yet fabricated. + +- **Module:** an ESP32-S3-MINI-1U-N8 on the top, between the macro buttons and USB, turned 270 degrees. The 19.2 mm WROOM-1U does not fit the 17.5 mm there. The turn puts the pinless GND edge on the side and the signal pins toward the stick, the OLED and the carrier; pins are assigned by position, as `GPIO_table.md` explains. USB runs about 15 mm as a result, which is well within full-speed limits. Bluetooth and ESP-NOW work with no other radio. +- **XBee:** optional. U_XBEE1 is a row of 12 hand-solder pads on the bottom for a 22 x 17 mm castellated daughter board, which carries the XBee 3 Micro, its decoupling, the RESET pull-up and RC, and the ATTN/BOOTMODE pull-up. The link is UART with flow control, not SPI. RTS and DTR also allow XBee serial firmware recovery through the ESP32. Leave the area inside the pads free of parts; vias there stay tented. See `GPIO_table.md`. +- **Reflow:** the bottom side goes first and the top side last, because Espressif requires a single reflow for the module (datasheet section 12.3). The XBee reflows on its own carrier and never goes upside down, which is what stopped the two modules from sharing this board before. +- **Radio link:** Amidala's droids use XBee Zigbee 3.0, so a Zigbee controller needs the carrier. The firmware still has to move from the XBee's SPI interface to UART, and needs a V2 pin map. +- **Programming:** USB, through the module's native USB. To force download mode, hold SW_BOOT1 while pressing the power button. The latch only stays on through the power button or `PWR_HOLD`, not USB, so hold the power button while flashing a new board. +- **No reset button:** the power button can only turn the board on, and PWR_HOLD on RXD0 keeps its pull-up through a reset, so a reset reboots the board and does not turn it off. Firmware must keep a watchdog running to recover from a hang. If firmware hangs before it can drive `PWR_HOLD` low on shutdown, disconnecting the battery is the only way off. - **Buttons:** all 13 connect directly to module GPIOs. See `GPIO_table.md`. -- **Power blocks:** the buck, charger and power latch keep V1's exact relative placement and routing, moved as rigid blocks. The buck and charger are mirrored onto the top side, near USB; the latch stays on the bottom. Two charger GND vias were later moved 0.1-0.75 mm in V1's layout to clear earlier button positions. The latch is too long to fit whole, so it is split at `PWR_BTN_TRIGGER`: the switch and `PWR_LATCH_G` node sit under the stick, turned 270 degrees, and the inverter sits beside the stick's lower pins. Change them as blocks, and see `diagrams/` for why they are arranged this way. -- **Hall sensor:** U_HALL1 sits off-center at (20.3, 4.0) mm, 7.8 mm from the stick's top sensing block rather than 3.3 mm, to reduce magnetic coupling. Confirm on a real stick. -- **Mounting:** four Ø2.2 mm unplated holes, MH1-4, at (2.5, 2.6), (27.4, 2.8), (3, 62.5) and (27, 67) from the top-left corner, for M2 self-tapping screws into shell posts. MH3 sits above the power button, which holds the true corner, so a Ø4 post clears `C_VIN_1` and `C_DBNC1` by only about 0.15 mm. +- **Power blocks:** the buck, charger and power latch follow V1's relative placement, all on the bottom. Two charger GND vias were moved 0.1-0.75 mm in V1's layout to clear earlier button positions. C_BUCK_IN1 turned 90 degrees with its VSYS pad straight above the VIN pin. BUCK_FB runs around the input cap and hops to F.Cu past the inductor, so both planes shield it; keep it out from under L_BUCK1. The latch is too long to fit whole, so it is split at `PWR_BTN_TRIGGER`: the switch and `PWR_LATCH_G` node sit under the stick, turned 270 degrees, and the inverter sits beside the stick's lower pins. See `diagrams/` for why they are arranged this way. +- **OLED cable:** U_OLED1's opening faces USB, and a Qwiic plug is 7.0 mm wide with its protrusions, so keep top-side parts out of x 0.9-7.9 mm from the mouth at y 52.7 mm down to the MH3 post. Check that a real cable goes in before committing the shell. +- **Hall sensor:** U_HALL1 is on the bottom at (6.5, 4.75) mm, rotated 180 degrees, forward and left of the stick, 7.8 mm from its nearest pot pin in plan view against about 15.4 mm on V1. A 2 x 2 mm N52 magnet swings up to sit directly under the package centre. Keep at least 1.8 mm from the top of the package to the magnet at full press, or the output clips at the sensor's ±44 mT range. The stick reading against trigger travel still needs a bench test. +- **Mounting:** four Ø2.2 mm unplated holes, MH1-4, at (2.5, 2.6), (27.4, 2.8), (3, 62.5) and (27, 67) from the top-left corner, for M2 self-tapping screws into shell posts. MH3 sits above the power button, which holds the true corner, so a Ø4 post clears `C_DBNC1` by only about 0.15 mm. The carrier has a long shallow chamfer at that corner, which also clears a Ø4 post on the bottom. - **Battery:** BT1 is a 2-pin JST PH, the common connector on pouch cells this size: pin 1 VBAT, pin 2 GND. R_TS1 ties the charger's TS pin to a fixed 10 kΩ, so there is no pack temperature monitoring. Check the polarity of the cell's lead before plugging it in. - **USB and status LED:** J_USB1 sits 2 mm right of centre, with its CC resistors and TVS moved with it. D_RGB1 sits between SW_PWR1 and J_USB1, turned 90 degrees. - **Through-board parts:** the Alps pegs, stick pins, USB stakes and BT1 pins all reach the other side. @@ -33,7 +34,8 @@ See [`GPIO_table.md`](GPIO_table.md) for every module pin. | Component | Part | Notes | Layout diagram | |---|---|---|---| -| MCU and radio | Fanstel BT840XE | nRF52840 with SKY66112 PA, +21 dBm, u.FL, 15 x 28 x 1.9 mm. Runs the firmware and the Zigbee link | — | +| MCU and radio | Espressif ESP32-S3-MINI-1U-N8 | Wi-Fi, Bluetooth LE and ESP-NOW, 8 MB flash, 15.4 x 15.4 x 2.4 mm, external antenna | — | +| XBee (optional) | Digi XB3-24Z8UM on a castellated carrier | Zigbee 3.0, +19 dBm, U.FL. Hand-soldered to the underside | — | | Display | SSD1306 1.3" OLED | 128x64, monochrome, I2C | — | | Hall trigger | DRV5055A2QDBZR (SOT-23) | Ratiometric linear hall effect, 3.3V. On the bottom of the board under the trigger magnet; senses the field perpendicular to the board. Trigger calibration accepts either magnet polarity | — | | Thumbstick | GuliKit hall effect module | Native 3.3V, analog X/Y + click | — | @@ -62,8 +64,8 @@ files are organized. ### Decoupling Caps | Component | Value | Notes | |---|---|---| -| DRV5055 VCC | 100nF ceramic | On 3V3_RF | -| GuliKit VCC | 100nF ceramic | On 3V3_RF | +| DRV5055 VCC | 100nF ceramic | | +| GuliKit VCC | 100nF ceramic | | | SK6812 VCC | 100nF ceramic | Close to supply pin | | ICM-42670-P | 100nF + 2.2µF on VDD, 10nF on VDDIO | Close to their pins | | OLED connector | 1µF + 100nF ceramic | | @@ -71,9 +73,10 @@ files are organized. | bq25185 SYS | 10µF + 100nF ceramic | | | bq25185 BAT | 10µF ceramic | | | TLV62569 VIN | 10µF ceramic | | -| TLV62569 VOUT | 10µF ceramic | TI specifies 10-47 µF and the rail totals about 70 µF nominal, less under DC bias. Check with a load step | -| BT840XE VDD | 47µF + 10µF + 100nF ceramic | After FB_RF1, per Fanstel's noisy-supply note | -| BT840XE VBUS | 1µF ceramic | Kept small so VBUS stays near USB's 10 µF limit. Nordic's value is unconfirmed | +| TLV62569 VOUT | 22µF ceramic | As on V1. TI specifies 10-47 µF | +| ESP32-S3-MINI-1U 3V3 | 10µF + 100nF + 39pF ceramic | As on V1 | +| ESP32-S3-MINI-1U EN | 1µF ceramic | With R_EN_PU1, per Espressif | +| XBee VCC | 10µF + 1µF + 100nF + 47pF ceramic | On the carrier | ### Resistors | Signal | Value | Notes | @@ -82,10 +85,11 @@ files are organized. | bq25185 TS/MR | 10kΩ to GND | Required with no thermistor: floating means no charging | | I2C SDA/SCL | 4.7kΩ | So the IMU works with no OLED attached | | Boot button | 10kΩ to 3V3 | R_BOOT_PU1 | +| ESP32 EN | 10kΩ to 3V3 | R_EN_PU1 | +| USB D+/D- | 27Ω series | R_USB_DP1 and R_USB_DM1, as on V1 | | Trigger output | 1kΩ + 100nF | R_TRIG1 and C_TRIG1, about 1.6 kHz. The DRV5055 must not see a capacitor without a resistor | | SK6812 DIN | 470Ω | R_RGB1 | -USB D+/D- connect directly, with no series resistors. That is unconfirmed against Nordic's datasheet. ### Buttons No external parts. Every button wires to GND and a module GPIO, using the internal pull-ups; see [`GPIO_table.md`](GPIO_table.md). @@ -94,33 +98,33 @@ No external parts. Every button wires to GND and a module GPIO, using the intern ## Communication Architecture -The droids use XBee Zigbee 3.0, so the controller has to join that network. The nRF52840 runs the Zigbee stack, and the firmware for it is not written yet. Each droid has its own coordinator and PAN ID, and all coordinators share one AES key. +The droids use XBee Zigbee 3.0, so the controller joins that network through the XBee on the carrier, over UART in API mode. Each droid has its own coordinator and PAN ID, and all coordinators share one AES key. Without the carrier the ESP32 can use Bluetooth or ESP-NOW. --- ## Bringup Sequence Recommended bringup order: -1. Current-limited supply on VSYS: check 3V3 and idle current with the power button held. -2. Load the bootloader over SWD through J_SWD1, holding the power button. Confirm it drives `PWR_HOLD` high, enables the reset pin, and enumerates over USB. -3. Boot entry and reset: hold BOOT while pressing power, and confirm RESET forces the board off. +1. Current-limited supply on VSYS, with no carrier fitted: check 3V3 and idle current with the power button held. +2. Flash over USB, holding the power button, with SW_BOOT1 held if the chip does not enumerate. Confirm firmware drives `PWR_HOLD` high. +3. Tap power briefly to check that the EN delay does not lose the press. Trigger a watchdog reset and confirm the board reboots and stays on. 4. OLED and ICM-42670-P on I2C. 5. SK6812 RGB LED. 6. Buttons, using the pin table. 7. Charge status on STAT1 and STAT2, and VSYS sense. -8. DRV5055 and thumbstick on the ADC, with the SAADC's VDD/4 reference. Sweep the stick and the trigger together to measure how much each moves the other. -9. Radio: limit nRF TX to +2 dBm with ANT000, per Fanstel, and join a droid's network. +8. DRV5055 and thumbstick on the ADC. Sweep the stick and the trigger together to measure how much each moves the other. +9. Solder the carrier on. Check UART traffic, CTS, SLEEP_RQ and ON/SLEEP, then XBee reset, then join a droid's network. --- ## Power Architecture -- Battery → bq25185 (charger and power path, 4.2V, 500mA) → TLV62569 (3.3V buck) → 3V3 logic, and through FB_RF1 to 3V3_RF for the module, DRV5055 and thumbstick. +- Battery → bq25185 (charger and power path, 4.2V, 500mA) → TLV62569 (3.3V buck) → 3V3 for everything, including the carrier. - Power switch: soft latch (AO3401A PFET + AO3400A NFET) controls the TLV62569 EN pin. USB does not hold it on. -- Boot: press the power button → latch enables 3V3 → module boots → P1.13 goes high through D_OR2 to hold the latch. -- Shutdown: firmware sees a hold on P0.11 → graceful shutdown → P1.13 low → power cut. A reset also releases the latch. -- bq25185 STAT1 and STAT2 go to P1.14 and P1.15 (open drain, 10kΩ pull-ups to 3V3). -- Battery voltage: VSYS through R_VSYS1/R_VSYS2 to P0.05, reading VSYS/3. +- Boot: press the power button → latch enables 3V3 → module boots → RXD0 (IO44) goes high through D_OR2 to hold the latch. +- Shutdown: firmware sees a hold on IO33 → graceful shutdown → IO44 low → power cut. +- bq25185 STAT1 and STAT2 go to IO15 and IO14 (open drain, 10kΩ pull-ups to 3V3). +- Battery voltage: VSYS through R_VSYS1/R_VSYS2 to IO7, reading VSYS/3. - Below about 3.3 V on the battery the buck passes it through, and the DRV5055's minimum is 3.0 V, so the firmware cutoff should sit above that. ## Power Management diff --git a/PCB/v2.x/datasheets/BT840X_BT840XE_Product_Specifications_v1.26.pdf b/PCB/v2.x/datasheets/BT840X_BT840XE_Product_Specifications_v1.26.pdf deleted file mode 100644 index ac1c890..0000000 Binary files a/PCB/v2.x/datasheets/BT840X_BT840XE_Product_Specifications_v1.26.pdf and /dev/null differ diff --git a/PCB/v2.x/datasheets/ESP32-S3-MINI-1.pdf b/PCB/v2.x/datasheets/ESP32-S3-MINI-1.pdf new file mode 100644 index 0000000..040a140 Binary files /dev/null and b/PCB/v2.x/datasheets/ESP32-S3-MINI-1.pdf differ diff --git a/PCB/v2.x/datasheets/XBee3_Hardware_Reference_90001543.pdf b/PCB/v2.x/datasheets/XBee3_Hardware_Reference_90001543.pdf new file mode 100644 index 0000000..6e1e178 Binary files /dev/null and b/PCB/v2.x/datasheets/XBee3_Hardware_Reference_90001543.pdf differ diff --git a/PCB/v2.x/fp-lib-table b/PCB/v2.x/fp-lib-table index 2e35d66..0eaa917 100644 --- a/PCB/v2.x/fp-lib-table +++ b/PCB/v2.x/fp-lib-table @@ -3,5 +3,6 @@ (lib (name "SnipsControllers") (type "KiCad") (uri "${KIPRJMOD}/libraries/SnipsControllers.pretty") (options "") (descr "")) (lib (name "BQ25185DLHR") (type "KiCad") (uri "${KIPRJMOD}/libraries/BQ25185DLHR.pretty") (options "") (descr "")) (lib (name "SnipsControllers_Custom") (type "KiCad") (uri "${KIPRJMOD}/libraries/SnipsControllers_Custom.pretty") (options "") (descr "")) + (lib (name "Espressif") (type "KiCad") (uri "${KIPRJMOD}/libraries/Espressif.pretty") (options "") (descr "")) (lib (name "R2Builders") (type "KiCad") (uri "${KIPRJMOD}/libraries") (options "") (descr "")) ) diff --git a/PCB/v2.x/libraries/3dmodels/BT840X_outline.step b/PCB/v2.x/libraries/3dmodels/BT840X_outline.step deleted file mode 100644 index 424a142..0000000 --- a/PCB/v2.x/libraries/3dmodels/BT840X_outline.step +++ /dev/null @@ -1,48303 +0,0 @@ -ISO-10303-21; -HEADER; -FILE_DESCRIPTION((''),'2;1'); -FILE_NAME('BT832X','2018-12-11T',('yfb'),(''), -'PRO/ENGINEER BY PARAMETRIC TECHNOLOGY CORPORATION, 2010280', -'PRO/ENGINEER BY PARAMETRIC TECHNOLOGY CORPORATION, 2010280',''); -FILE_SCHEMA(('CONFIG_CONTROL_DESIGN','SHAPE_APPEARANCE_LAYERS_GROUPS')); -ENDSEC; -DATA; -#24=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.17E1)); -#25=DIRECTION('',(0.E0,-1.E0,0.E0)); -#26=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27=AXIS2_PLACEMENT_3D('',#24,#25,#26); -#29=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.17E1)); -#30=DIRECTION('',(0.E0,-1.E0,0.E0)); -#31=DIRECTION('',(1.E0,0.E0,0.E0)); -#32=AXIS2_PLACEMENT_3D('',#29,#30,#31); -#34=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.17E1)); -#35=DIRECTION('',(0.E0,-1.E0,0.E0)); -#36=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37=AXIS2_PLACEMENT_3D('',#34,#35,#36); -#39=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.17E1)); -#40=DIRECTION('',(0.E0,-1.E0,0.E0)); -#41=DIRECTION('',(1.E0,0.E0,0.E0)); -#42=AXIS2_PLACEMENT_3D('',#39,#40,#41); -#44=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.17E1)); -#45=DIRECTION('',(0.E0,-1.E0,0.E0)); -#46=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47=AXIS2_PLACEMENT_3D('',#44,#45,#46); -#49=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.17E1)); -#50=DIRECTION('',(0.E0,-1.E0,0.E0)); -#51=DIRECTION('',(1.E0,0.E0,0.E0)); -#52=AXIS2_PLACEMENT_3D('',#49,#50,#51); -#54=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.17E1)); -#55=DIRECTION('',(0.E0,-1.E0,0.E0)); -#56=DIRECTION('',(-1.E0,0.E0,0.E0)); -#57=AXIS2_PLACEMENT_3D('',#54,#55,#56); -#59=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.17E1)); -#60=DIRECTION('',(0.E0,-1.E0,0.E0)); -#61=DIRECTION('',(1.E0,0.E0,0.E0)); -#62=AXIS2_PLACEMENT_3D('',#59,#60,#61); -#64=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.05E1)); -#65=DIRECTION('',(0.E0,-1.E0,0.E0)); -#66=DIRECTION('',(-1.E0,0.E0,0.E0)); -#67=AXIS2_PLACEMENT_3D('',#64,#65,#66); -#69=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.05E1)); -#70=DIRECTION('',(0.E0,-1.E0,0.E0)); -#71=DIRECTION('',(1.E0,0.E0,0.E0)); -#72=AXIS2_PLACEMENT_3D('',#69,#70,#71); -#74=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.05E1)); -#75=DIRECTION('',(0.E0,-1.E0,0.E0)); -#76=DIRECTION('',(-1.E0,0.E0,0.E0)); -#77=AXIS2_PLACEMENT_3D('',#74,#75,#76); -#79=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.05E1)); -#80=DIRECTION('',(0.E0,-1.E0,0.E0)); -#81=DIRECTION('',(1.E0,0.E0,0.E0)); -#82=AXIS2_PLACEMENT_3D('',#79,#80,#81); -#84=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.05E1)); -#85=DIRECTION('',(0.E0,-1.E0,0.E0)); -#86=DIRECTION('',(-1.E0,0.E0,0.E0)); -#87=AXIS2_PLACEMENT_3D('',#84,#85,#86); -#89=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.05E1)); -#90=DIRECTION('',(0.E0,-1.E0,0.E0)); -#91=DIRECTION('',(1.E0,0.E0,0.E0)); -#92=AXIS2_PLACEMENT_3D('',#89,#90,#91); -#94=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.05E1)); -#95=DIRECTION('',(0.E0,-1.E0,0.E0)); -#96=DIRECTION('',(-1.E0,0.E0,0.E0)); -#97=AXIS2_PLACEMENT_3D('',#94,#95,#96); -#99=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.05E1)); -#100=DIRECTION('',(0.E0,-1.E0,0.E0)); -#101=DIRECTION('',(1.E0,0.E0,0.E0)); -#102=AXIS2_PLACEMENT_3D('',#99,#100,#101); -#104=CARTESIAN_POINT('',(2.75E0,-3.E-1,9.3E0)); -#105=DIRECTION('',(0.E0,-1.E0,0.E0)); -#106=DIRECTION('',(-1.E0,0.E0,0.E0)); -#107=AXIS2_PLACEMENT_3D('',#104,#105,#106); -#109=CARTESIAN_POINT('',(2.75E0,-3.E-1,9.3E0)); -#110=DIRECTION('',(0.E0,-1.E0,0.E0)); -#111=DIRECTION('',(1.E0,0.E0,0.E0)); -#112=AXIS2_PLACEMENT_3D('',#109,#110,#111); -#114=CARTESIAN_POINT('',(1.25E0,-3.E-1,9.3E0)); -#115=DIRECTION('',(0.E0,-1.E0,0.E0)); -#116=DIRECTION('',(-1.E0,0.E0,0.E0)); -#117=AXIS2_PLACEMENT_3D('',#114,#115,#116); -#119=CARTESIAN_POINT('',(1.25E0,-3.E-1,9.3E0)); -#120=DIRECTION('',(0.E0,-1.E0,0.E0)); -#121=DIRECTION('',(1.E0,0.E0,0.E0)); -#122=AXIS2_PLACEMENT_3D('',#119,#120,#121); -#124=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,9.3E0)); -#125=DIRECTION('',(0.E0,-1.E0,0.E0)); -#126=DIRECTION('',(-1.E0,0.E0,0.E0)); -#127=AXIS2_PLACEMENT_3D('',#124,#125,#126); -#129=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,9.3E0)); -#130=DIRECTION('',(0.E0,-1.E0,0.E0)); -#131=DIRECTION('',(1.E0,0.E0,0.E0)); -#132=AXIS2_PLACEMENT_3D('',#129,#130,#131); -#134=CARTESIAN_POINT('',(-1.75E0,-3.E-1,9.3E0)); -#135=DIRECTION('',(0.E0,-1.E0,0.E0)); -#136=DIRECTION('',(-1.E0,0.E0,0.E0)); -#137=AXIS2_PLACEMENT_3D('',#134,#135,#136); -#139=CARTESIAN_POINT('',(-1.75E0,-3.E-1,9.3E0)); -#140=DIRECTION('',(0.E0,-1.E0,0.E0)); -#141=DIRECTION('',(1.E0,0.E0,0.E0)); -#142=AXIS2_PLACEMENT_3D('',#139,#140,#141); -#144=CARTESIAN_POINT('',(2.75E0,-3.E-1,8.1E0)); -#145=DIRECTION('',(0.E0,-1.E0,0.E0)); -#146=DIRECTION('',(-1.E0,0.E0,0.E0)); -#147=AXIS2_PLACEMENT_3D('',#144,#145,#146); -#149=CARTESIAN_POINT('',(2.75E0,-3.E-1,8.1E0)); -#150=DIRECTION('',(0.E0,-1.E0,0.E0)); -#151=DIRECTION('',(1.E0,0.E0,0.E0)); -#152=AXIS2_PLACEMENT_3D('',#149,#150,#151); -#154=CARTESIAN_POINT('',(1.25E0,-3.E-1,8.1E0)); -#155=DIRECTION('',(0.E0,-1.E0,0.E0)); -#156=DIRECTION('',(-1.E0,0.E0,0.E0)); -#157=AXIS2_PLACEMENT_3D('',#154,#155,#156); -#159=CARTESIAN_POINT('',(1.25E0,-3.E-1,8.1E0)); -#160=DIRECTION('',(0.E0,-1.E0,0.E0)); -#161=DIRECTION('',(1.E0,0.E0,0.E0)); -#162=AXIS2_PLACEMENT_3D('',#159,#160,#161); -#164=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,8.1E0)); -#165=DIRECTION('',(0.E0,-1.E0,0.E0)); -#166=DIRECTION('',(-1.E0,0.E0,0.E0)); -#167=AXIS2_PLACEMENT_3D('',#164,#165,#166); -#169=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,8.1E0)); -#170=DIRECTION('',(0.E0,-1.E0,0.E0)); -#171=DIRECTION('',(1.E0,0.E0,0.E0)); -#172=AXIS2_PLACEMENT_3D('',#169,#170,#171); -#174=CARTESIAN_POINT('',(-1.75E0,-3.E-1,8.1E0)); -#175=DIRECTION('',(0.E0,-1.E0,0.E0)); -#176=DIRECTION('',(-1.E0,0.E0,0.E0)); -#177=AXIS2_PLACEMENT_3D('',#174,#175,#176); -#179=CARTESIAN_POINT('',(-1.75E0,-3.E-1,8.1E0)); -#180=DIRECTION('',(0.E0,-1.E0,0.E0)); -#181=DIRECTION('',(1.E0,0.E0,0.E0)); -#182=AXIS2_PLACEMENT_3D('',#179,#180,#181); -#184=CARTESIAN_POINT('',(2.75E0,-3.E-1,6.9E0)); -#185=DIRECTION('',(0.E0,-1.E0,0.E0)); -#186=DIRECTION('',(-1.E0,0.E0,0.E0)); -#187=AXIS2_PLACEMENT_3D('',#184,#185,#186); -#189=CARTESIAN_POINT('',(2.75E0,-3.E-1,6.9E0)); -#190=DIRECTION('',(0.E0,-1.E0,0.E0)); -#191=DIRECTION('',(1.E0,0.E0,0.E0)); -#192=AXIS2_PLACEMENT_3D('',#189,#190,#191); -#194=CARTESIAN_POINT('',(1.25E0,-3.E-1,6.9E0)); -#195=DIRECTION('',(0.E0,-1.E0,0.E0)); -#196=DIRECTION('',(-1.E0,0.E0,0.E0)); -#197=AXIS2_PLACEMENT_3D('',#194,#195,#196); -#199=CARTESIAN_POINT('',(1.25E0,-3.E-1,6.9E0)); -#200=DIRECTION('',(0.E0,-1.E0,0.E0)); -#201=DIRECTION('',(1.E0,0.E0,0.E0)); -#202=AXIS2_PLACEMENT_3D('',#199,#200,#201); -#204=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,6.9E0)); -#205=DIRECTION('',(0.E0,-1.E0,0.E0)); -#206=DIRECTION('',(-1.E0,0.E0,0.E0)); -#207=AXIS2_PLACEMENT_3D('',#204,#205,#206); -#209=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,6.9E0)); -#210=DIRECTION('',(0.E0,-1.E0,0.E0)); -#211=DIRECTION('',(1.E0,0.E0,0.E0)); -#212=AXIS2_PLACEMENT_3D('',#209,#210,#211); -#214=CARTESIAN_POINT('',(-1.75E0,-3.E-1,6.9E0)); -#215=DIRECTION('',(0.E0,-1.E0,0.E0)); -#216=DIRECTION('',(-1.E0,0.E0,0.E0)); -#217=AXIS2_PLACEMENT_3D('',#214,#215,#216); -#219=CARTESIAN_POINT('',(-1.75E0,-3.E-1,6.9E0)); -#220=DIRECTION('',(0.E0,-1.E0,0.E0)); -#221=DIRECTION('',(1.E0,0.E0,0.E0)); -#222=AXIS2_PLACEMENT_3D('',#219,#220,#221); -#224=CARTESIAN_POINT('',(2.75E0,-3.E-1,5.7E0)); -#225=DIRECTION('',(0.E0,-1.E0,0.E0)); -#226=DIRECTION('',(-1.E0,0.E0,0.E0)); -#227=AXIS2_PLACEMENT_3D('',#224,#225,#226); -#229=CARTESIAN_POINT('',(2.75E0,-3.E-1,5.7E0)); -#230=DIRECTION('',(0.E0,-1.E0,0.E0)); -#231=DIRECTION('',(1.E0,0.E0,0.E0)); -#232=AXIS2_PLACEMENT_3D('',#229,#230,#231); -#234=CARTESIAN_POINT('',(1.25E0,-3.E-1,5.7E0)); -#235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#236=DIRECTION('',(-1.E0,0.E0,0.E0)); -#237=AXIS2_PLACEMENT_3D('',#234,#235,#236); -#239=CARTESIAN_POINT('',(1.25E0,-3.E-1,5.7E0)); -#240=DIRECTION('',(0.E0,-1.E0,0.E0)); -#241=DIRECTION('',(1.E0,0.E0,0.E0)); -#242=AXIS2_PLACEMENT_3D('',#239,#240,#241); -#244=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,5.7E0)); -#245=DIRECTION('',(0.E0,-1.E0,0.E0)); -#246=DIRECTION('',(-1.E0,0.E0,0.E0)); -#247=AXIS2_PLACEMENT_3D('',#244,#245,#246); -#249=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,5.7E0)); -#250=DIRECTION('',(0.E0,-1.E0,0.E0)); -#251=DIRECTION('',(1.E0,0.E0,0.E0)); -#252=AXIS2_PLACEMENT_3D('',#249,#250,#251); -#254=CARTESIAN_POINT('',(-1.75E0,-3.E-1,5.7E0)); -#255=DIRECTION('',(0.E0,-1.E0,0.E0)); -#256=DIRECTION('',(-1.E0,0.E0,0.E0)); -#257=AXIS2_PLACEMENT_3D('',#254,#255,#256); -#259=CARTESIAN_POINT('',(-1.75E0,-3.E-1,5.7E0)); -#260=DIRECTION('',(0.E0,-1.E0,0.E0)); -#261=DIRECTION('',(1.E0,0.E0,0.E0)); -#262=AXIS2_PLACEMENT_3D('',#259,#260,#261); -#264=DIRECTION('',(0.E0,0.E0,1.E0)); -#265=VECTOR('',#264,1.5E0); -#266=CARTESIAN_POINT('',(4.625E0,-3.E-1,2.95E0)); -#267=LINE('',#266,#265); -#268=DIRECTION('',(-1.E0,0.E0,0.E0)); -#269=VECTOR('',#268,1.5E0); -#270=CARTESIAN_POINT('',(4.625E0,-3.E-1,4.45E0)); -#271=LINE('',#270,#269); -#272=DIRECTION('',(0.E0,0.E0,-1.E0)); -#273=VECTOR('',#272,1.5E0); -#274=CARTESIAN_POINT('',(3.125E0,-3.E-1,4.45E0)); -#275=LINE('',#274,#273); -#276=DIRECTION('',(1.E0,0.E0,0.E0)); -#277=VECTOR('',#276,1.5E0); -#278=CARTESIAN_POINT('',(3.125E0,-3.E-1,2.95E0)); -#279=LINE('',#278,#277); -#280=DIRECTION('',(0.E0,0.E0,1.E0)); -#281=VECTOR('',#280,1.5E0); -#282=CARTESIAN_POINT('',(2.375E0,-3.E-1,2.95E0)); -#283=LINE('',#282,#281); -#284=DIRECTION('',(-1.E0,0.E0,0.E0)); -#285=VECTOR('',#284,1.5E0); -#286=CARTESIAN_POINT('',(2.375E0,-3.E-1,4.45E0)); -#287=LINE('',#286,#285); -#288=DIRECTION('',(0.E0,0.E0,-1.E0)); -#289=VECTOR('',#288,1.5E0); -#290=CARTESIAN_POINT('',(8.75E-1,-3.E-1,4.45E0)); -#291=LINE('',#290,#289); -#292=DIRECTION('',(1.E0,0.E0,0.E0)); -#293=VECTOR('',#292,1.5E0); -#294=CARTESIAN_POINT('',(8.75E-1,-3.E-1,2.95E0)); -#295=LINE('',#294,#293); -#296=DIRECTION('',(1.E0,0.E0,0.E0)); -#297=VECTOR('',#296,1.5E0); -#298=CARTESIAN_POINT('',(-3.625E0,-3.E-1,2.95E0)); -#299=LINE('',#298,#297); -#300=DIRECTION('',(0.E0,0.E0,1.E0)); -#301=VECTOR('',#300,1.5E0); -#302=CARTESIAN_POINT('',(-2.125E0,-3.E-1,2.95E0)); -#303=LINE('',#302,#301); -#304=DIRECTION('',(-1.E0,0.E0,0.E0)); -#305=VECTOR('',#304,1.5E0); -#306=CARTESIAN_POINT('',(-2.125E0,-3.E-1,4.45E0)); -#307=LINE('',#306,#305); -#308=DIRECTION('',(0.E0,0.E0,-1.E0)); -#309=VECTOR('',#308,1.5E0); -#310=CARTESIAN_POINT('',(-3.625E0,-3.E-1,4.45E0)); -#311=LINE('',#310,#309); -#312=DIRECTION('',(1.E0,0.E0,0.E0)); -#313=VECTOR('',#312,1.5E0); -#314=CARTESIAN_POINT('',(-1.375E0,-3.E-1,2.95E0)); -#315=LINE('',#314,#313); -#316=DIRECTION('',(0.E0,0.E0,1.E0)); -#317=VECTOR('',#316,1.5E0); -#318=CARTESIAN_POINT('',(1.25E-1,-3.E-1,2.95E0)); -#319=LINE('',#318,#317); -#320=DIRECTION('',(-1.E0,0.E0,0.E0)); -#321=VECTOR('',#320,1.5E0); -#322=CARTESIAN_POINT('',(1.25E-1,-3.E-1,4.45E0)); -#323=LINE('',#322,#321); -#324=DIRECTION('',(0.E0,0.E0,-1.E0)); -#325=VECTOR('',#324,1.5E0); -#326=CARTESIAN_POINT('',(-1.375E0,-3.E-1,4.45E0)); -#327=LINE('',#326,#325); -#328=DIRECTION('',(0.E0,0.E0,1.E0)); -#329=VECTOR('',#328,6.E-1); -#330=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.4035E1)); -#331=LINE('',#330,#329); -#332=DIRECTION('',(1.E0,0.E0,0.E0)); -#333=VECTOR('',#332,3.5E-1); -#334=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.3435E1)); -#335=LINE('',#334,#333); -#336=DIRECTION('',(0.E0,0.E0,1.E0)); -#337=VECTOR('',#336,5.E-1); -#338=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.3435E1)); -#339=LINE('',#338,#337); -#340=DIRECTION('',(1.E0,0.E0,0.E0)); -#341=VECTOR('',#340,3.5E-1); -#342=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2935E1)); -#343=LINE('',#342,#341); -#344=DIRECTION('',(0.E0,0.E0,1.E0)); -#345=VECTOR('',#344,6.E-1); -#346=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2935E1)); -#347=LINE('',#346,#345); -#348=DIRECTION('',(1.E0,0.E0,0.E0)); -#349=VECTOR('',#348,3.5E-1); -#350=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2335E1)); -#351=LINE('',#350,#349); -#352=DIRECTION('',(0.E0,0.E0,1.E0)); -#353=VECTOR('',#352,5.E-1); -#354=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2335E1)); -#355=LINE('',#354,#353); -#356=DIRECTION('',(1.E0,0.E0,0.E0)); -#357=VECTOR('',#356,3.5E-1); -#358=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1835E1)); -#359=LINE('',#358,#357); -#360=DIRECTION('',(0.E0,0.E0,1.E0)); -#361=VECTOR('',#360,6.E-1); -#362=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1835E1)); -#363=LINE('',#362,#361); -#364=DIRECTION('',(1.E0,0.E0,0.E0)); -#365=VECTOR('',#364,3.5E-1); -#366=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1235E1)); -#367=LINE('',#366,#365); -#368=DIRECTION('',(0.E0,0.E0,1.E0)); -#369=VECTOR('',#368,1.2235E1); -#370=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1235E1)); -#371=LINE('',#370,#369); -#372=DIRECTION('',(1.E0,0.E0,0.E0)); -#373=VECTOR('',#372,1.E0); -#374=CARTESIAN_POINT('',(-7.5E0,-3.E-1,1.E0)); -#375=LINE('',#374,#373); -#376=DIRECTION('',(0.E0,0.E0,1.E0)); -#377=VECTOR('',#376,3.55E0); -#378=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#379=LINE('',#378,#377); -#380=DIRECTION('',(-1.E0,0.E0,0.E0)); -#381=VECTOR('',#380,6.E-1); -#382=CARTESIAN_POINT('',(-5.9E0,-3.E-1,4.55E0)); -#383=LINE('',#382,#381); -#384=DIRECTION('',(0.E0,0.E0,-1.E0)); -#385=VECTOR('',#384,7.E-1); -#386=CARTESIAN_POINT('',(-5.9E0,-3.E-1,5.25E0)); -#387=LINE('',#386,#385); -#388=DIRECTION('',(1.E0,0.E0,0.E0)); -#389=VECTOR('',#388,6.E-1); -#390=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.25E0)); -#391=LINE('',#390,#389); -#392=DIRECTION('',(0.E0,0.E0,1.E0)); -#393=VECTOR('',#392,4.E-1); -#394=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.25E0)); -#395=LINE('',#394,#393); -#396=DIRECTION('',(-1.E0,0.E0,0.E0)); -#397=VECTOR('',#396,6.E-1); -#398=CARTESIAN_POINT('',(-5.9E0,-3.E-1,5.65E0)); -#399=LINE('',#398,#397); -#400=DIRECTION('',(0.E0,0.E0,-1.E0)); -#401=VECTOR('',#400,7.E-1); -#402=CARTESIAN_POINT('',(-5.9E0,-3.E-1,6.35E0)); -#403=LINE('',#402,#401); -#404=DIRECTION('',(1.E0,0.E0,0.E0)); -#405=VECTOR('',#404,6.E-1); -#406=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.35E0)); -#407=LINE('',#406,#405); -#408=DIRECTION('',(0.E0,0.E0,1.E0)); -#409=VECTOR('',#408,4.E-1); -#410=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.35E0)); -#411=LINE('',#410,#409); -#412=DIRECTION('',(-1.E0,0.E0,0.E0)); -#413=VECTOR('',#412,6.E-1); -#414=CARTESIAN_POINT('',(-5.9E0,-3.E-1,6.75E0)); -#415=LINE('',#414,#413); -#416=DIRECTION('',(0.E0,0.E0,-1.E0)); -#417=VECTOR('',#416,7.E-1); -#418=CARTESIAN_POINT('',(-5.9E0,-3.E-1,7.45E0)); -#419=LINE('',#418,#417); -#420=DIRECTION('',(1.E0,0.E0,0.E0)); -#421=VECTOR('',#420,6.E-1); -#422=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.45E0)); -#423=LINE('',#422,#421); -#424=DIRECTION('',(0.E0,0.E0,1.E0)); -#425=VECTOR('',#424,4.E-1); -#426=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.45E0)); -#427=LINE('',#426,#425); -#428=DIRECTION('',(-1.E0,0.E0,0.E0)); -#429=VECTOR('',#428,6.E-1); -#430=CARTESIAN_POINT('',(-5.9E0,-3.E-1,7.85E0)); -#431=LINE('',#430,#429); -#432=DIRECTION('',(0.E0,0.E0,-1.E0)); -#433=VECTOR('',#432,7.E-1); -#434=CARTESIAN_POINT('',(-5.9E0,-3.E-1,8.55E0)); -#435=LINE('',#434,#433); -#436=DIRECTION('',(1.E0,0.E0,0.E0)); -#437=VECTOR('',#436,6.E-1); -#438=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.55E0)); -#439=LINE('',#438,#437); -#440=DIRECTION('',(0.E0,0.E0,1.E0)); -#441=VECTOR('',#440,4.E-1); -#442=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.55E0)); -#443=LINE('',#442,#441); -#444=DIRECTION('',(-1.E0,0.E0,0.E0)); -#445=VECTOR('',#444,6.E-1); -#446=CARTESIAN_POINT('',(-5.9E0,-3.E-1,8.95E0)); -#447=LINE('',#446,#445); -#448=DIRECTION('',(0.E0,0.E0,-1.E0)); -#449=VECTOR('',#448,7.E-1); -#450=CARTESIAN_POINT('',(-5.9E0,-3.E-1,9.65E0)); -#451=LINE('',#450,#449); -#452=DIRECTION('',(1.E0,0.E0,0.E0)); -#453=VECTOR('',#452,6.E-1); -#454=CARTESIAN_POINT('',(-6.5E0,-3.E-1,9.65E0)); -#455=LINE('',#454,#453); -#456=DIRECTION('',(0.E0,0.E0,1.E0)); -#457=VECTOR('',#456,4.E-1); -#458=CARTESIAN_POINT('',(-6.5E0,-3.E-1,9.65E0)); -#459=LINE('',#458,#457); -#460=DIRECTION('',(-1.E0,0.E0,0.E0)); -#461=VECTOR('',#460,6.E-1); -#462=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.005E1)); -#463=LINE('',#462,#461); -#464=DIRECTION('',(0.E0,0.E0,-1.E0)); -#465=VECTOR('',#464,7.E-1); -#466=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.075E1)); -#467=LINE('',#466,#465); -#468=DIRECTION('',(1.E0,0.E0,0.E0)); -#469=VECTOR('',#468,6.E-1); -#470=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.075E1)); -#471=LINE('',#470,#469); -#472=DIRECTION('',(0.E0,0.E0,1.E0)); -#473=VECTOR('',#472,4.E-1); -#474=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.075E1)); -#475=LINE('',#474,#473); -#476=DIRECTION('',(-1.E0,0.E0,0.E0)); -#477=VECTOR('',#476,6.E-1); -#478=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.115E1)); -#479=LINE('',#478,#477); -#480=DIRECTION('',(0.E0,0.E0,-1.E0)); -#481=VECTOR('',#480,7.E-1); -#482=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.185E1)); -#483=LINE('',#482,#481); -#484=DIRECTION('',(1.E0,0.E0,0.E0)); -#485=VECTOR('',#484,6.E-1); -#486=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.185E1)); -#487=LINE('',#486,#485); -#488=DIRECTION('',(0.E0,0.E0,1.E0)); -#489=VECTOR('',#488,4.E-1); -#490=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.185E1)); -#491=LINE('',#490,#489); -#492=DIRECTION('',(-1.E0,0.E0,0.E0)); -#493=VECTOR('',#492,6.E-1); -#494=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.225E1)); -#495=LINE('',#494,#493); -#496=DIRECTION('',(0.E0,0.E0,-1.E0)); -#497=VECTOR('',#496,7.E-1); -#498=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.295E1)); -#499=LINE('',#498,#497); -#500=DIRECTION('',(1.E0,0.E0,0.E0)); -#501=VECTOR('',#500,6.E-1); -#502=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.295E1)); -#503=LINE('',#502,#501); -#504=DIRECTION('',(0.E0,0.E0,1.E0)); -#505=VECTOR('',#504,7.5E-1); -#506=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.295E1)); -#507=LINE('',#506,#505); -#508=DIRECTION('',(1.E0,0.E0,0.E0)); -#509=VECTOR('',#508,1.4E1); -#510=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.37E1)); -#511=LINE('',#510,#509); -#512=DIRECTION('',(0.E0,0.E0,-1.E0)); -#513=VECTOR('',#512,7.5E-1); -#514=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#515=LINE('',#514,#513); -#516=DIRECTION('',(-1.E0,0.E0,0.E0)); -#517=VECTOR('',#516,6.E-1); -#518=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.295E1)); -#519=LINE('',#518,#517); -#520=DIRECTION('',(0.E0,0.E0,1.E0)); -#521=VECTOR('',#520,7.E-1); -#522=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.225E1)); -#523=LINE('',#522,#521); -#524=DIRECTION('',(-1.E0,0.E0,0.E0)); -#525=VECTOR('',#524,6.E-1); -#526=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.225E1)); -#527=LINE('',#526,#525); -#528=DIRECTION('',(0.E0,0.E0,-1.E0)); -#529=VECTOR('',#528,4.E-1); -#530=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.225E1)); -#531=LINE('',#530,#529); -#532=DIRECTION('',(-1.E0,0.E0,0.E0)); -#533=VECTOR('',#532,6.E-1); -#534=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.185E1)); -#535=LINE('',#534,#533); -#536=DIRECTION('',(0.E0,0.E0,1.E0)); -#537=VECTOR('',#536,7.E-1); -#538=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.115E1)); -#539=LINE('',#538,#537); -#540=DIRECTION('',(-1.E0,0.E0,0.E0)); -#541=VECTOR('',#540,6.E-1); -#542=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.115E1)); -#543=LINE('',#542,#541); -#544=DIRECTION('',(0.E0,0.E0,-1.E0)); -#545=VECTOR('',#544,4.E-1); -#546=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.115E1)); -#547=LINE('',#546,#545); -#548=DIRECTION('',(-1.E0,0.E0,0.E0)); -#549=VECTOR('',#548,6.E-1); -#550=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.075E1)); -#551=LINE('',#550,#549); -#552=DIRECTION('',(0.E0,0.E0,1.E0)); -#553=VECTOR('',#552,7.E-1); -#554=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.005E1)); -#555=LINE('',#554,#553); -#556=DIRECTION('',(-1.E0,0.E0,0.E0)); -#557=VECTOR('',#556,6.E-1); -#558=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.005E1)); -#559=LINE('',#558,#557); -#560=DIRECTION('',(0.E0,0.E0,-1.E0)); -#561=VECTOR('',#560,4.E-1); -#562=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.005E1)); -#563=LINE('',#562,#561); -#564=DIRECTION('',(-1.E0,0.E0,0.E0)); -#565=VECTOR('',#564,6.E-1); -#566=CARTESIAN_POINT('',(7.5E0,-3.E-1,9.65E0)); -#567=LINE('',#566,#565); -#568=DIRECTION('',(0.E0,0.E0,1.E0)); -#569=VECTOR('',#568,7.E-1); -#570=CARTESIAN_POINT('',(6.9E0,-3.E-1,8.95E0)); -#571=LINE('',#570,#569); -#572=DIRECTION('',(-1.E0,0.E0,0.E0)); -#573=VECTOR('',#572,6.E-1); -#574=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.95E0)); -#575=LINE('',#574,#573); -#576=DIRECTION('',(0.E0,0.E0,-1.E0)); -#577=VECTOR('',#576,4.E-1); -#578=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.95E0)); -#579=LINE('',#578,#577); -#580=DIRECTION('',(-1.E0,0.E0,0.E0)); -#581=VECTOR('',#580,6.E-1); -#582=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.55E0)); -#583=LINE('',#582,#581); -#584=DIRECTION('',(0.E0,0.E0,1.E0)); -#585=VECTOR('',#584,7.E-1); -#586=CARTESIAN_POINT('',(6.9E0,-3.E-1,7.85E0)); -#587=LINE('',#586,#585); -#588=DIRECTION('',(-1.E0,0.E0,0.E0)); -#589=VECTOR('',#588,6.E-1); -#590=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.85E0)); -#591=LINE('',#590,#589); -#592=DIRECTION('',(0.E0,0.E0,-1.E0)); -#593=VECTOR('',#592,4.E-1); -#594=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.85E0)); -#595=LINE('',#594,#593); -#596=DIRECTION('',(-1.E0,0.E0,0.E0)); -#597=VECTOR('',#596,6.E-1); -#598=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.45E0)); -#599=LINE('',#598,#597); -#600=DIRECTION('',(0.E0,0.E0,1.E0)); -#601=VECTOR('',#600,7.E-1); -#602=CARTESIAN_POINT('',(6.9E0,-3.E-1,6.75E0)); -#603=LINE('',#602,#601); -#604=DIRECTION('',(-1.E0,0.E0,0.E0)); -#605=VECTOR('',#604,6.E-1); -#606=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.75E0)); -#607=LINE('',#606,#605); -#608=DIRECTION('',(0.E0,0.E0,-1.E0)); -#609=VECTOR('',#608,4.E-1); -#610=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.75E0)); -#611=LINE('',#610,#609); -#612=DIRECTION('',(-1.E0,0.E0,0.E0)); -#613=VECTOR('',#612,6.E-1); -#614=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.35E0)); -#615=LINE('',#614,#613); -#616=DIRECTION('',(0.E0,0.E0,1.E0)); -#617=VECTOR('',#616,7.E-1); -#618=CARTESIAN_POINT('',(6.9E0,-3.E-1,5.65E0)); -#619=LINE('',#618,#617); -#620=DIRECTION('',(-1.E0,0.E0,0.E0)); -#621=VECTOR('',#620,6.E-1); -#622=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.65E0)); -#623=LINE('',#622,#621); -#624=DIRECTION('',(0.E0,0.E0,-1.E0)); -#625=VECTOR('',#624,4.E-1); -#626=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.65E0)); -#627=LINE('',#626,#625); -#628=DIRECTION('',(-1.E0,0.E0,0.E0)); -#629=VECTOR('',#628,6.E-1); -#630=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.25E0)); -#631=LINE('',#630,#629); -#632=DIRECTION('',(0.E0,0.E0,1.E0)); -#633=VECTOR('',#632,7.E-1); -#634=CARTESIAN_POINT('',(6.9E0,-3.E-1,4.55E0)); -#635=LINE('',#634,#633); -#636=DIRECTION('',(-1.E0,0.E0,0.E0)); -#637=VECTOR('',#636,6.E-1); -#638=CARTESIAN_POINT('',(7.5E0,-3.E-1,4.55E0)); -#639=LINE('',#638,#637); -#640=DIRECTION('',(0.E0,0.E0,-1.E0)); -#641=VECTOR('',#640,1.885E1); -#642=CARTESIAN_POINT('',(7.5E0,-3.E-1,4.55E0)); -#643=LINE('',#642,#641); -#644=DIRECTION('',(-1.E0,0.E0,0.E0)); -#645=VECTOR('',#644,1.5E1); -#646=CARTESIAN_POINT('',(7.5E0,-3.E-1,-1.43E1)); -#647=LINE('',#646,#645); -#648=DIRECTION('',(0.E0,0.E0,1.E0)); -#649=VECTOR('',#648,2.65E-1); -#650=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#651=LINE('',#650,#649); -#652=DIRECTION('',(1.E0,0.E0,0.E0)); -#653=VECTOR('',#652,3.5E-1); -#654=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.4035E1)); -#655=LINE('',#654,#653); -#656=DIRECTION('',(0.E0,1.E0,0.E0)); -#657=VECTOR('',#656,5.E-2); -#658=CARTESIAN_POINT('',(2.45E0,-3.E-1,1.17E1)); -#659=LINE('',#658,#657); -#660=DIRECTION('',(0.E0,1.E0,0.E0)); -#661=VECTOR('',#660,5.E-2); -#662=CARTESIAN_POINT('',(3.05E0,-3.E-1,1.17E1)); -#663=LINE('',#662,#661); -#664=CARTESIAN_POINT('',(2.75E0,-2.5E-1,1.17E1)); -#665=DIRECTION('',(0.E0,1.E0,0.E0)); -#666=DIRECTION('',(1.E0,0.E0,0.E0)); -#667=AXIS2_PLACEMENT_3D('',#664,#665,#666); -#669=CARTESIAN_POINT('',(2.75E0,-2.5E-1,1.17E1)); -#670=DIRECTION('',(0.E0,1.E0,0.E0)); -#671=DIRECTION('',(-1.E0,0.E0,0.E0)); -#672=AXIS2_PLACEMENT_3D('',#669,#670,#671); -#674=CARTESIAN_POINT('',(1.25E0,-2.5E-1,1.17E1)); -#675=DIRECTION('',(0.E0,1.E0,0.E0)); -#676=DIRECTION('',(1.E0,0.E0,0.E0)); -#677=AXIS2_PLACEMENT_3D('',#674,#675,#676); -#679=CARTESIAN_POINT('',(1.25E0,-2.5E-1,1.17E1)); -#680=DIRECTION('',(0.E0,1.E0,0.E0)); -#681=DIRECTION('',(-1.E0,0.E0,0.E0)); -#682=AXIS2_PLACEMENT_3D('',#679,#680,#681); -#684=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,1.17E1)); -#685=DIRECTION('',(0.E0,1.E0,0.E0)); -#686=DIRECTION('',(1.E0,0.E0,0.E0)); -#687=AXIS2_PLACEMENT_3D('',#684,#685,#686); -#689=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,1.17E1)); -#690=DIRECTION('',(0.E0,1.E0,0.E0)); -#691=DIRECTION('',(-1.E0,0.E0,0.E0)); -#692=AXIS2_PLACEMENT_3D('',#689,#690,#691); -#694=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,1.17E1)); -#695=DIRECTION('',(0.E0,1.E0,0.E0)); -#696=DIRECTION('',(1.E0,0.E0,0.E0)); -#697=AXIS2_PLACEMENT_3D('',#694,#695,#696); -#699=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,1.17E1)); -#700=DIRECTION('',(0.E0,1.E0,0.E0)); -#701=DIRECTION('',(-1.E0,0.E0,0.E0)); -#702=AXIS2_PLACEMENT_3D('',#699,#700,#701); -#704=DIRECTION('',(0.E0,1.E0,0.E0)); -#705=VECTOR('',#704,5.E-2); -#706=CARTESIAN_POINT('',(9.5E-1,-3.E-1,1.17E1)); -#707=LINE('',#706,#705); -#708=DIRECTION('',(0.E0,1.E0,0.E0)); -#709=VECTOR('',#708,5.E-2); -#710=CARTESIAN_POINT('',(1.55E0,-3.E-1,1.17E1)); -#711=LINE('',#710,#709); -#712=DIRECTION('',(0.E0,1.E0,0.E0)); -#713=VECTOR('',#712,5.E-2); -#714=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,1.17E1)); -#715=LINE('',#714,#713); -#716=DIRECTION('',(0.E0,1.E0,0.E0)); -#717=VECTOR('',#716,5.E-2); -#718=CARTESIAN_POINT('',(5.E-2,-3.E-1,1.17E1)); -#719=LINE('',#718,#717); -#720=DIRECTION('',(0.E0,1.E0,0.E0)); -#721=VECTOR('',#720,5.E-2); -#722=CARTESIAN_POINT('',(-2.05E0,-3.E-1,1.17E1)); -#723=LINE('',#722,#721); -#724=DIRECTION('',(0.E0,1.E0,0.E0)); -#725=VECTOR('',#724,5.E-2); -#726=CARTESIAN_POINT('',(-1.45E0,-3.E-1,1.17E1)); -#727=LINE('',#726,#725); -#728=DIRECTION('',(0.E0,1.E0,0.E0)); -#729=VECTOR('',#728,5.E-2); -#730=CARTESIAN_POINT('',(2.45E0,-3.E-1,1.05E1)); -#731=LINE('',#730,#729); -#732=DIRECTION('',(0.E0,1.E0,0.E0)); -#733=VECTOR('',#732,5.E-2); -#734=CARTESIAN_POINT('',(3.05E0,-3.E-1,1.05E1)); -#735=LINE('',#734,#733); -#736=CARTESIAN_POINT('',(2.75E0,-2.5E-1,1.05E1)); -#737=DIRECTION('',(0.E0,-1.E0,0.E0)); -#738=DIRECTION('',(-1.E0,0.E0,0.E0)); -#739=AXIS2_PLACEMENT_3D('',#736,#737,#738); -#741=CARTESIAN_POINT('',(2.75E0,-2.5E-1,1.05E1)); -#742=DIRECTION('',(0.E0,-1.E0,0.E0)); -#743=DIRECTION('',(1.E0,0.E0,0.E0)); -#744=AXIS2_PLACEMENT_3D('',#741,#742,#743); -#746=CARTESIAN_POINT('',(1.25E0,-2.5E-1,1.05E1)); -#747=DIRECTION('',(0.E0,-1.E0,0.E0)); -#748=DIRECTION('',(-1.E0,0.E0,0.E0)); -#749=AXIS2_PLACEMENT_3D('',#746,#747,#748); -#751=CARTESIAN_POINT('',(1.25E0,-2.5E-1,1.05E1)); -#752=DIRECTION('',(0.E0,-1.E0,0.E0)); -#753=DIRECTION('',(1.E0,0.E0,0.E0)); -#754=AXIS2_PLACEMENT_3D('',#751,#752,#753); -#756=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,1.05E1)); -#757=DIRECTION('',(0.E0,-1.E0,0.E0)); -#758=DIRECTION('',(-1.E0,0.E0,0.E0)); -#759=AXIS2_PLACEMENT_3D('',#756,#757,#758); -#761=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,1.05E1)); -#762=DIRECTION('',(0.E0,-1.E0,0.E0)); -#763=DIRECTION('',(1.E0,0.E0,0.E0)); -#764=AXIS2_PLACEMENT_3D('',#761,#762,#763); -#766=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,1.05E1)); -#767=DIRECTION('',(0.E0,-1.E0,0.E0)); -#768=DIRECTION('',(-1.E0,0.E0,0.E0)); -#769=AXIS2_PLACEMENT_3D('',#766,#767,#768); -#771=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,1.05E1)); -#772=DIRECTION('',(0.E0,-1.E0,0.E0)); -#773=DIRECTION('',(1.E0,0.E0,0.E0)); -#774=AXIS2_PLACEMENT_3D('',#771,#772,#773); -#776=DIRECTION('',(0.E0,1.E0,0.E0)); -#777=VECTOR('',#776,5.E-2); -#778=CARTESIAN_POINT('',(9.5E-1,-3.E-1,1.05E1)); -#779=LINE('',#778,#777); -#780=DIRECTION('',(0.E0,1.E0,0.E0)); -#781=VECTOR('',#780,5.E-2); -#782=CARTESIAN_POINT('',(1.55E0,-3.E-1,1.05E1)); -#783=LINE('',#782,#781); -#784=DIRECTION('',(0.E0,1.E0,0.E0)); -#785=VECTOR('',#784,5.E-2); -#786=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,1.05E1)); -#787=LINE('',#786,#785); -#788=DIRECTION('',(0.E0,1.E0,0.E0)); -#789=VECTOR('',#788,5.E-2); -#790=CARTESIAN_POINT('',(5.E-2,-3.E-1,1.05E1)); -#791=LINE('',#790,#789); -#792=DIRECTION('',(0.E0,1.E0,0.E0)); -#793=VECTOR('',#792,5.E-2); -#794=CARTESIAN_POINT('',(-2.05E0,-3.E-1,1.05E1)); -#795=LINE('',#794,#793); -#796=DIRECTION('',(0.E0,1.E0,0.E0)); -#797=VECTOR('',#796,5.E-2); -#798=CARTESIAN_POINT('',(-1.45E0,-3.E-1,1.05E1)); -#799=LINE('',#798,#797); -#800=DIRECTION('',(0.E0,1.E0,0.E0)); -#801=VECTOR('',#800,5.E-2); -#802=CARTESIAN_POINT('',(2.45E0,-3.E-1,9.3E0)); -#803=LINE('',#802,#801); -#804=DIRECTION('',(0.E0,1.E0,0.E0)); -#805=VECTOR('',#804,5.E-2); -#806=CARTESIAN_POINT('',(3.05E0,-3.E-1,9.3E0)); -#807=LINE('',#806,#805); -#808=CARTESIAN_POINT('',(2.75E0,-2.5E-1,9.3E0)); -#809=DIRECTION('',(0.E0,-1.E0,0.E0)); -#810=DIRECTION('',(-1.E0,0.E0,0.E0)); -#811=AXIS2_PLACEMENT_3D('',#808,#809,#810); -#813=CARTESIAN_POINT('',(2.75E0,-2.5E-1,9.3E0)); -#814=DIRECTION('',(0.E0,-1.E0,0.E0)); -#815=DIRECTION('',(1.E0,0.E0,0.E0)); -#816=AXIS2_PLACEMENT_3D('',#813,#814,#815); -#818=CARTESIAN_POINT('',(1.25E0,-2.5E-1,9.3E0)); -#819=DIRECTION('',(0.E0,-1.E0,0.E0)); -#820=DIRECTION('',(-1.E0,0.E0,0.E0)); -#821=AXIS2_PLACEMENT_3D('',#818,#819,#820); -#823=CARTESIAN_POINT('',(1.25E0,-2.5E-1,9.3E0)); -#824=DIRECTION('',(0.E0,-1.E0,0.E0)); -#825=DIRECTION('',(1.E0,0.E0,0.E0)); -#826=AXIS2_PLACEMENT_3D('',#823,#824,#825); -#828=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,9.3E0)); -#829=DIRECTION('',(0.E0,-1.E0,0.E0)); -#830=DIRECTION('',(-1.E0,0.E0,0.E0)); -#831=AXIS2_PLACEMENT_3D('',#828,#829,#830); -#833=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,9.3E0)); -#834=DIRECTION('',(0.E0,-1.E0,0.E0)); -#835=DIRECTION('',(1.E0,0.E0,0.E0)); -#836=AXIS2_PLACEMENT_3D('',#833,#834,#835); -#838=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,9.3E0)); -#839=DIRECTION('',(0.E0,-1.E0,0.E0)); -#840=DIRECTION('',(-1.E0,0.E0,0.E0)); -#841=AXIS2_PLACEMENT_3D('',#838,#839,#840); -#843=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,9.3E0)); -#844=DIRECTION('',(0.E0,-1.E0,0.E0)); -#845=DIRECTION('',(1.E0,0.E0,0.E0)); -#846=AXIS2_PLACEMENT_3D('',#843,#844,#845); -#848=DIRECTION('',(0.E0,1.E0,0.E0)); -#849=VECTOR('',#848,5.E-2); -#850=CARTESIAN_POINT('',(9.5E-1,-3.E-1,9.3E0)); -#851=LINE('',#850,#849); -#852=DIRECTION('',(0.E0,1.E0,0.E0)); -#853=VECTOR('',#852,5.E-2); -#854=CARTESIAN_POINT('',(1.55E0,-3.E-1,9.3E0)); -#855=LINE('',#854,#853); -#856=DIRECTION('',(0.E0,1.E0,0.E0)); -#857=VECTOR('',#856,5.E-2); -#858=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,9.3E0)); -#859=LINE('',#858,#857); -#860=DIRECTION('',(0.E0,1.E0,0.E0)); -#861=VECTOR('',#860,5.E-2); -#862=CARTESIAN_POINT('',(5.E-2,-3.E-1,9.3E0)); -#863=LINE('',#862,#861); -#864=DIRECTION('',(0.E0,1.E0,0.E0)); -#865=VECTOR('',#864,5.E-2); -#866=CARTESIAN_POINT('',(-2.05E0,-3.E-1,9.3E0)); -#867=LINE('',#866,#865); -#868=DIRECTION('',(0.E0,1.E0,0.E0)); -#869=VECTOR('',#868,5.E-2); -#870=CARTESIAN_POINT('',(-1.45E0,-3.E-1,9.3E0)); -#871=LINE('',#870,#869); -#872=DIRECTION('',(0.E0,1.E0,0.E0)); -#873=VECTOR('',#872,5.E-2); -#874=CARTESIAN_POINT('',(2.45E0,-3.E-1,8.1E0)); -#875=LINE('',#874,#873); -#876=DIRECTION('',(0.E0,1.E0,0.E0)); -#877=VECTOR('',#876,5.E-2); -#878=CARTESIAN_POINT('',(3.05E0,-3.E-1,8.1E0)); -#879=LINE('',#878,#877); -#880=CARTESIAN_POINT('',(2.75E0,-2.5E-1,8.1E0)); -#881=DIRECTION('',(0.E0,-1.E0,0.E0)); -#882=DIRECTION('',(-1.E0,0.E0,0.E0)); -#883=AXIS2_PLACEMENT_3D('',#880,#881,#882); -#885=CARTESIAN_POINT('',(2.75E0,-2.5E-1,8.1E0)); -#886=DIRECTION('',(0.E0,-1.E0,0.E0)); -#887=DIRECTION('',(1.E0,0.E0,0.E0)); -#888=AXIS2_PLACEMENT_3D('',#885,#886,#887); -#890=CARTESIAN_POINT('',(1.25E0,-2.5E-1,8.1E0)); -#891=DIRECTION('',(0.E0,-1.E0,0.E0)); -#892=DIRECTION('',(-1.E0,0.E0,0.E0)); -#893=AXIS2_PLACEMENT_3D('',#890,#891,#892); -#895=CARTESIAN_POINT('',(1.25E0,-2.5E-1,8.1E0)); -#896=DIRECTION('',(0.E0,-1.E0,0.E0)); -#897=DIRECTION('',(1.E0,0.E0,0.E0)); -#898=AXIS2_PLACEMENT_3D('',#895,#896,#897); -#900=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,8.1E0)); -#901=DIRECTION('',(0.E0,-1.E0,0.E0)); -#902=DIRECTION('',(-1.E0,0.E0,0.E0)); -#903=AXIS2_PLACEMENT_3D('',#900,#901,#902); -#905=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,8.1E0)); -#906=DIRECTION('',(0.E0,-1.E0,0.E0)); -#907=DIRECTION('',(1.E0,0.E0,0.E0)); -#908=AXIS2_PLACEMENT_3D('',#905,#906,#907); -#910=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,8.1E0)); -#911=DIRECTION('',(0.E0,-1.E0,0.E0)); -#912=DIRECTION('',(-1.E0,0.E0,0.E0)); -#913=AXIS2_PLACEMENT_3D('',#910,#911,#912); -#915=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,8.1E0)); -#916=DIRECTION('',(0.E0,-1.E0,0.E0)); -#917=DIRECTION('',(1.E0,0.E0,0.E0)); -#918=AXIS2_PLACEMENT_3D('',#915,#916,#917); -#920=DIRECTION('',(0.E0,1.E0,0.E0)); -#921=VECTOR('',#920,5.E-2); -#922=CARTESIAN_POINT('',(9.5E-1,-3.E-1,8.1E0)); -#923=LINE('',#922,#921); -#924=DIRECTION('',(0.E0,1.E0,0.E0)); -#925=VECTOR('',#924,5.E-2); -#926=CARTESIAN_POINT('',(1.55E0,-3.E-1,8.1E0)); -#927=LINE('',#926,#925); -#928=DIRECTION('',(0.E0,1.E0,0.E0)); -#929=VECTOR('',#928,5.E-2); -#930=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,8.1E0)); -#931=LINE('',#930,#929); -#932=DIRECTION('',(0.E0,1.E0,0.E0)); -#933=VECTOR('',#932,5.E-2); -#934=CARTESIAN_POINT('',(5.E-2,-3.E-1,8.1E0)); -#935=LINE('',#934,#933); -#936=DIRECTION('',(0.E0,1.E0,0.E0)); -#937=VECTOR('',#936,5.E-2); -#938=CARTESIAN_POINT('',(-2.05E0,-3.E-1,8.1E0)); -#939=LINE('',#938,#937); -#940=DIRECTION('',(0.E0,1.E0,0.E0)); -#941=VECTOR('',#940,5.E-2); -#942=CARTESIAN_POINT('',(-1.45E0,-3.E-1,8.1E0)); -#943=LINE('',#942,#941); -#944=DIRECTION('',(0.E0,1.E0,0.E0)); -#945=VECTOR('',#944,5.E-2); -#946=CARTESIAN_POINT('',(2.45E0,-3.E-1,6.9E0)); -#947=LINE('',#946,#945); -#948=DIRECTION('',(0.E0,1.E0,0.E0)); -#949=VECTOR('',#948,5.E-2); -#950=CARTESIAN_POINT('',(3.05E0,-3.E-1,6.9E0)); -#951=LINE('',#950,#949); -#952=CARTESIAN_POINT('',(2.75E0,-2.5E-1,6.9E0)); -#953=DIRECTION('',(0.E0,-1.E0,0.E0)); -#954=DIRECTION('',(-1.E0,0.E0,0.E0)); -#955=AXIS2_PLACEMENT_3D('',#952,#953,#954); -#957=CARTESIAN_POINT('',(2.75E0,-2.5E-1,6.9E0)); -#958=DIRECTION('',(0.E0,-1.E0,0.E0)); -#959=DIRECTION('',(1.E0,0.E0,0.E0)); -#960=AXIS2_PLACEMENT_3D('',#957,#958,#959); -#962=CARTESIAN_POINT('',(1.25E0,-2.5E-1,6.9E0)); -#963=DIRECTION('',(0.E0,-1.E0,0.E0)); -#964=DIRECTION('',(-1.E0,0.E0,0.E0)); -#965=AXIS2_PLACEMENT_3D('',#962,#963,#964); -#967=CARTESIAN_POINT('',(1.25E0,-2.5E-1,6.9E0)); -#968=DIRECTION('',(0.E0,-1.E0,0.E0)); -#969=DIRECTION('',(1.E0,0.E0,0.E0)); -#970=AXIS2_PLACEMENT_3D('',#967,#968,#969); -#972=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,6.9E0)); -#973=DIRECTION('',(0.E0,-1.E0,0.E0)); -#974=DIRECTION('',(-1.E0,0.E0,0.E0)); -#975=AXIS2_PLACEMENT_3D('',#972,#973,#974); -#977=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,6.9E0)); -#978=DIRECTION('',(0.E0,-1.E0,0.E0)); -#979=DIRECTION('',(1.E0,0.E0,0.E0)); -#980=AXIS2_PLACEMENT_3D('',#977,#978,#979); -#982=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,6.9E0)); -#983=DIRECTION('',(0.E0,-1.E0,0.E0)); -#984=DIRECTION('',(-1.E0,0.E0,0.E0)); -#985=AXIS2_PLACEMENT_3D('',#982,#983,#984); -#987=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,6.9E0)); -#988=DIRECTION('',(0.E0,-1.E0,0.E0)); -#989=DIRECTION('',(1.E0,0.E0,0.E0)); -#990=AXIS2_PLACEMENT_3D('',#987,#988,#989); -#992=DIRECTION('',(0.E0,1.E0,0.E0)); -#993=VECTOR('',#992,5.E-2); -#994=CARTESIAN_POINT('',(9.5E-1,-3.E-1,6.9E0)); -#995=LINE('',#994,#993); -#996=DIRECTION('',(0.E0,1.E0,0.E0)); -#997=VECTOR('',#996,5.E-2); -#998=CARTESIAN_POINT('',(1.55E0,-3.E-1,6.9E0)); -#999=LINE('',#998,#997); -#1000=DIRECTION('',(0.E0,1.E0,0.E0)); -#1001=VECTOR('',#1000,5.E-2); -#1002=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,6.9E0)); -#1003=LINE('',#1002,#1001); -#1004=DIRECTION('',(0.E0,1.E0,0.E0)); -#1005=VECTOR('',#1004,5.E-2); -#1006=CARTESIAN_POINT('',(5.E-2,-3.E-1,6.9E0)); -#1007=LINE('',#1006,#1005); -#1008=DIRECTION('',(0.E0,1.E0,0.E0)); -#1009=VECTOR('',#1008,5.E-2); -#1010=CARTESIAN_POINT('',(-2.05E0,-3.E-1,6.9E0)); -#1011=LINE('',#1010,#1009); -#1012=DIRECTION('',(0.E0,1.E0,0.E0)); -#1013=VECTOR('',#1012,5.E-2); -#1014=CARTESIAN_POINT('',(-1.45E0,-3.E-1,6.9E0)); -#1015=LINE('',#1014,#1013); -#1016=DIRECTION('',(0.E0,1.E0,0.E0)); -#1017=VECTOR('',#1016,5.E-2); -#1018=CARTESIAN_POINT('',(2.45E0,-3.E-1,5.7E0)); -#1019=LINE('',#1018,#1017); -#1020=DIRECTION('',(0.E0,1.E0,0.E0)); -#1021=VECTOR('',#1020,5.E-2); -#1022=CARTESIAN_POINT('',(3.05E0,-3.E-1,5.7E0)); -#1023=LINE('',#1022,#1021); -#1024=CARTESIAN_POINT('',(2.75E0,-2.5E-1,5.7E0)); -#1025=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1026=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1027=AXIS2_PLACEMENT_3D('',#1024,#1025,#1026); -#1029=CARTESIAN_POINT('',(2.75E0,-2.5E-1,5.7E0)); -#1030=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1031=DIRECTION('',(1.E0,0.E0,0.E0)); -#1032=AXIS2_PLACEMENT_3D('',#1029,#1030,#1031); -#1034=CARTESIAN_POINT('',(1.25E0,-2.5E-1,5.7E0)); -#1035=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1036=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1037=AXIS2_PLACEMENT_3D('',#1034,#1035,#1036); -#1039=CARTESIAN_POINT('',(1.25E0,-2.5E-1,5.7E0)); -#1040=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1041=DIRECTION('',(1.E0,0.E0,0.E0)); -#1042=AXIS2_PLACEMENT_3D('',#1039,#1040,#1041); -#1044=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,5.7E0)); -#1045=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1046=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1047=AXIS2_PLACEMENT_3D('',#1044,#1045,#1046); -#1049=CARTESIAN_POINT('',(-2.5E-1,-2.5E-1,5.7E0)); -#1050=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1051=DIRECTION('',(1.E0,0.E0,0.E0)); -#1052=AXIS2_PLACEMENT_3D('',#1049,#1050,#1051); -#1054=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,5.7E0)); -#1055=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1056=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1057=AXIS2_PLACEMENT_3D('',#1054,#1055,#1056); -#1059=CARTESIAN_POINT('',(-1.75E0,-2.5E-1,5.7E0)); -#1060=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1061=DIRECTION('',(1.E0,0.E0,0.E0)); -#1062=AXIS2_PLACEMENT_3D('',#1059,#1060,#1061); -#1064=DIRECTION('',(0.E0,1.E0,0.E0)); -#1065=VECTOR('',#1064,5.E-2); -#1066=CARTESIAN_POINT('',(9.5E-1,-3.E-1,5.7E0)); -#1067=LINE('',#1066,#1065); -#1068=DIRECTION('',(0.E0,1.E0,0.E0)); -#1069=VECTOR('',#1068,5.E-2); -#1070=CARTESIAN_POINT('',(1.55E0,-3.E-1,5.7E0)); -#1071=LINE('',#1070,#1069); -#1072=DIRECTION('',(0.E0,1.E0,0.E0)); -#1073=VECTOR('',#1072,5.E-2); -#1074=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,5.7E0)); -#1075=LINE('',#1074,#1073); -#1076=DIRECTION('',(0.E0,1.E0,0.E0)); -#1077=VECTOR('',#1076,5.E-2); -#1078=CARTESIAN_POINT('',(5.E-2,-3.E-1,5.7E0)); -#1079=LINE('',#1078,#1077); -#1080=DIRECTION('',(0.E0,1.E0,0.E0)); -#1081=VECTOR('',#1080,5.E-2); -#1082=CARTESIAN_POINT('',(-2.05E0,-3.E-1,5.7E0)); -#1083=LINE('',#1082,#1081); -#1084=DIRECTION('',(0.E0,1.E0,0.E0)); -#1085=VECTOR('',#1084,5.E-2); -#1086=CARTESIAN_POINT('',(-1.45E0,-3.E-1,5.7E0)); -#1087=LINE('',#1086,#1085); -#1088=DIRECTION('',(0.E0,1.E0,0.E0)); -#1089=VECTOR('',#1088,5.E-2); -#1090=CARTESIAN_POINT('',(4.625E0,-3.E-1,2.95E0)); -#1091=LINE('',#1090,#1089); -#1092=DIRECTION('',(0.E0,1.E0,0.E0)); -#1093=VECTOR('',#1092,5.E-2); -#1094=CARTESIAN_POINT('',(3.125E0,-3.E-1,2.95E0)); -#1095=LINE('',#1094,#1093); -#1096=DIRECTION('',(0.E0,1.E0,0.E0)); -#1097=VECTOR('',#1096,5.E-2); -#1098=CARTESIAN_POINT('',(3.125E0,-3.E-1,4.45E0)); -#1099=LINE('',#1098,#1097); -#1100=DIRECTION('',(0.E0,1.E0,0.E0)); -#1101=VECTOR('',#1100,5.E-2); -#1102=CARTESIAN_POINT('',(4.625E0,-3.E-1,4.45E0)); -#1103=LINE('',#1102,#1101); -#1104=DIRECTION('',(0.E0,0.E0,1.E0)); -#1105=VECTOR('',#1104,1.5E0); -#1106=CARTESIAN_POINT('',(4.625E0,-2.5E-1,2.95E0)); -#1107=LINE('',#1106,#1105); -#1108=DIRECTION('',(1.E0,0.E0,0.E0)); -#1109=VECTOR('',#1108,1.5E0); -#1110=CARTESIAN_POINT('',(3.125E0,-2.5E-1,2.95E0)); -#1111=LINE('',#1110,#1109); -#1112=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1113=VECTOR('',#1112,1.5E0); -#1114=CARTESIAN_POINT('',(3.125E0,-2.5E-1,4.45E0)); -#1115=LINE('',#1114,#1113); -#1116=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1117=VECTOR('',#1116,1.5E0); -#1118=CARTESIAN_POINT('',(4.625E0,-2.5E-1,4.45E0)); -#1119=LINE('',#1118,#1117); -#1120=DIRECTION('',(0.E0,0.E0,1.E0)); -#1121=VECTOR('',#1120,1.5E0); -#1122=CARTESIAN_POINT('',(2.375E0,-2.5E-1,2.95E0)); -#1123=LINE('',#1122,#1121); -#1124=DIRECTION('',(1.E0,0.E0,0.E0)); -#1125=VECTOR('',#1124,1.5E0); -#1126=CARTESIAN_POINT('',(8.75E-1,-2.5E-1,2.95E0)); -#1127=LINE('',#1126,#1125); -#1128=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1129=VECTOR('',#1128,1.5E0); -#1130=CARTESIAN_POINT('',(8.75E-1,-2.5E-1,4.45E0)); -#1131=LINE('',#1130,#1129); -#1132=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1133=VECTOR('',#1132,1.5E0); -#1134=CARTESIAN_POINT('',(2.375E0,-2.5E-1,4.45E0)); -#1135=LINE('',#1134,#1133); -#1136=DIRECTION('',(1.E0,0.E0,0.E0)); -#1137=VECTOR('',#1136,1.5E0); -#1138=CARTESIAN_POINT('',(-3.625E0,-2.5E-1,2.95E0)); -#1139=LINE('',#1138,#1137); -#1140=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1141=VECTOR('',#1140,1.5E0); -#1142=CARTESIAN_POINT('',(-3.625E0,-2.5E-1,4.45E0)); -#1143=LINE('',#1142,#1141); -#1144=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1145=VECTOR('',#1144,1.5E0); -#1146=CARTESIAN_POINT('',(-2.125E0,-2.5E-1,4.45E0)); -#1147=LINE('',#1146,#1145); -#1148=DIRECTION('',(0.E0,0.E0,1.E0)); -#1149=VECTOR('',#1148,1.5E0); -#1150=CARTESIAN_POINT('',(-2.125E0,-2.5E-1,2.95E0)); -#1151=LINE('',#1150,#1149); -#1152=DIRECTION('',(1.E0,0.E0,0.E0)); -#1153=VECTOR('',#1152,1.5E0); -#1154=CARTESIAN_POINT('',(-1.375E0,-2.5E-1,2.95E0)); -#1155=LINE('',#1154,#1153); -#1156=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1157=VECTOR('',#1156,1.5E0); -#1158=CARTESIAN_POINT('',(-1.375E0,-2.5E-1,4.45E0)); -#1159=LINE('',#1158,#1157); -#1160=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1161=VECTOR('',#1160,1.5E0); -#1162=CARTESIAN_POINT('',(1.25E-1,-2.5E-1,4.45E0)); -#1163=LINE('',#1162,#1161); -#1164=DIRECTION('',(0.E0,0.E0,1.E0)); -#1165=VECTOR('',#1164,1.5E0); -#1166=CARTESIAN_POINT('',(1.25E-1,-2.5E-1,2.95E0)); -#1167=LINE('',#1166,#1165); -#1168=DIRECTION('',(0.E0,1.E0,0.E0)); -#1169=VECTOR('',#1168,5.E-2); -#1170=CARTESIAN_POINT('',(2.375E0,-3.E-1,2.95E0)); -#1171=LINE('',#1170,#1169); -#1172=DIRECTION('',(0.E0,1.E0,0.E0)); -#1173=VECTOR('',#1172,5.E-2); -#1174=CARTESIAN_POINT('',(8.75E-1,-3.E-1,2.95E0)); -#1175=LINE('',#1174,#1173); -#1176=DIRECTION('',(0.E0,1.E0,0.E0)); -#1177=VECTOR('',#1176,5.E-2); -#1178=CARTESIAN_POINT('',(8.75E-1,-3.E-1,4.45E0)); -#1179=LINE('',#1178,#1177); -#1180=DIRECTION('',(0.E0,1.E0,0.E0)); -#1181=VECTOR('',#1180,5.E-2); -#1182=CARTESIAN_POINT('',(2.375E0,-3.E-1,4.45E0)); -#1183=LINE('',#1182,#1181); -#1184=DIRECTION('',(0.E0,1.E0,0.E0)); -#1185=VECTOR('',#1184,5.E-2); -#1186=CARTESIAN_POINT('',(-3.625E0,-3.E-1,2.95E0)); -#1187=LINE('',#1186,#1185); -#1188=DIRECTION('',(0.E0,1.E0,0.E0)); -#1189=VECTOR('',#1188,5.E-2); -#1190=CARTESIAN_POINT('',(-3.625E0,-3.E-1,4.45E0)); -#1191=LINE('',#1190,#1189); -#1192=DIRECTION('',(0.E0,1.E0,0.E0)); -#1193=VECTOR('',#1192,5.E-2); -#1194=CARTESIAN_POINT('',(-2.125E0,-3.E-1,4.45E0)); -#1195=LINE('',#1194,#1193); -#1196=DIRECTION('',(0.E0,1.E0,0.E0)); -#1197=VECTOR('',#1196,5.E-2); -#1198=CARTESIAN_POINT('',(-2.125E0,-3.E-1,2.95E0)); -#1199=LINE('',#1198,#1197); -#1200=DIRECTION('',(0.E0,1.E0,0.E0)); -#1201=VECTOR('',#1200,5.E-2); -#1202=CARTESIAN_POINT('',(-1.375E0,-3.E-1,2.95E0)); -#1203=LINE('',#1202,#1201); -#1204=DIRECTION('',(0.E0,1.E0,0.E0)); -#1205=VECTOR('',#1204,5.E-2); -#1206=CARTESIAN_POINT('',(-1.375E0,-3.E-1,4.45E0)); -#1207=LINE('',#1206,#1205); -#1208=DIRECTION('',(0.E0,1.E0,0.E0)); -#1209=VECTOR('',#1208,5.E-2); -#1210=CARTESIAN_POINT('',(1.25E-1,-3.E-1,4.45E0)); -#1211=LINE('',#1210,#1209); -#1212=DIRECTION('',(0.E0,1.E0,0.E0)); -#1213=VECTOR('',#1212,5.E-2); -#1214=CARTESIAN_POINT('',(1.25E-1,-3.E-1,2.95E0)); -#1215=LINE('',#1214,#1213); -#1216=DIRECTION('',(0.E0,1.E0,0.E0)); -#1217=VECTOR('',#1216,5.E-2); -#1218=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.4035E1)); -#1219=LINE('',#1218,#1217); -#1220=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1221=VECTOR('',#1220,5.505102572168E-2); -#1222=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.1235E1)); -#1223=LINE('',#1222,#1221); -#1224=DIRECTION('',(0.E0,1.E0,0.E0)); -#1225=VECTOR('',#1224,5.5E-1); -#1226=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.129005102572E1)); -#1227=LINE('',#1226,#1225); -#1228=DIRECTION('',(0.E0,1.E0,0.E0)); -#1229=VECTOR('',#1228,5.E-2); -#1230=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1235E1)); -#1231=LINE('',#1230,#1229); -#1232=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1233=VECTOR('',#1232,5.505102572168E-2); -#1234=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.177994897428E1)); -#1235=LINE('',#1234,#1233); -#1236=DIRECTION('',(0.E0,1.E0,0.E0)); -#1237=VECTOR('',#1236,5.E-2); -#1238=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1835E1)); -#1239=LINE('',#1238,#1237); -#1240=DIRECTION('',(0.E0,1.E0,0.E0)); -#1241=VECTOR('',#1240,5.E-2); -#1242=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2335E1)); -#1243=LINE('',#1242,#1241); -#1244=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1245=VECTOR('',#1244,5.505102572168E-2); -#1246=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.2335E1)); -#1247=LINE('',#1246,#1245); -#1248=DIRECTION('',(0.E0,1.E0,0.E0)); -#1249=VECTOR('',#1248,5.5E-1); -#1250=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.239005102572E1)); -#1251=LINE('',#1250,#1249); -#1252=DIRECTION('',(0.E0,1.E0,0.E0)); -#1253=VECTOR('',#1252,5.5E-1); -#1254=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.177994897428E1)); -#1255=LINE('',#1254,#1253); -#1256=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1257=VECTOR('',#1256,5.505102572168E-2); -#1258=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.287994897428E1)); -#1259=LINE('',#1258,#1257); -#1260=DIRECTION('',(0.E0,1.E0,0.E0)); -#1261=VECTOR('',#1260,5.E-2); -#1262=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2935E1)); -#1263=LINE('',#1262,#1261); -#1264=DIRECTION('',(0.E0,1.E0,0.E0)); -#1265=VECTOR('',#1264,5.E-2); -#1266=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.3435E1)); -#1267=LINE('',#1266,#1265); -#1268=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1269=VECTOR('',#1268,5.505102572168E-2); -#1270=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.3435E1)); -#1271=LINE('',#1270,#1269); -#1272=DIRECTION('',(0.E0,1.E0,0.E0)); -#1273=VECTOR('',#1272,5.5E-1); -#1274=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.349005102572E1)); -#1275=LINE('',#1274,#1273); -#1276=DIRECTION('',(0.E0,1.E0,0.E0)); -#1277=VECTOR('',#1276,5.5E-1); -#1278=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.287994897428E1)); -#1279=LINE('',#1278,#1277); -#1280=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1281=VECTOR('',#1280,5.505102572168E-2); -#1282=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.397994897428E1)); -#1283=LINE('',#1282,#1281); -#1284=DIRECTION('',(0.E0,1.E0,0.E0)); -#1285=VECTOR('',#1284,5.E-2); -#1286=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.4035E1)); -#1287=LINE('',#1286,#1285); -#1288=DIRECTION('',(0.E0,1.E0,0.E0)); -#1289=VECTOR('',#1288,6.E-1); -#1290=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#1291=LINE('',#1290,#1289); -#1292=DIRECTION('',(0.E0,1.E0,0.E0)); -#1293=VECTOR('',#1292,5.5E-1); -#1294=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.397994897428E1)); -#1295=LINE('',#1294,#1293); -#1296=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1297=VECTOR('',#1296,3.5E-1); -#1298=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.1235E1)); -#1299=LINE('',#1298,#1297); -#1300=DIRECTION('',(0.E0,0.E0,1.E0)); -#1301=VECTOR('',#1300,6.E-1); -#1302=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.1835E1)); -#1303=LINE('',#1302,#1301); -#1304=DIRECTION('',(1.E0,0.E0,0.E0)); -#1305=VECTOR('',#1304,3.5E-1); -#1306=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.1835E1)); -#1307=LINE('',#1306,#1305); -#1308=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1309=VECTOR('',#1308,3.5E-1); -#1310=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.2335E1)); -#1311=LINE('',#1310,#1309); -#1312=DIRECTION('',(0.E0,0.E0,1.E0)); -#1313=VECTOR('',#1312,6.E-1); -#1314=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.2935E1)); -#1315=LINE('',#1314,#1313); -#1316=DIRECTION('',(1.E0,0.E0,0.E0)); -#1317=VECTOR('',#1316,3.5E-1); -#1318=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.2935E1)); -#1319=LINE('',#1318,#1317); -#1320=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1321=VECTOR('',#1320,3.5E-1); -#1322=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.3435E1)); -#1323=LINE('',#1322,#1321); -#1324=DIRECTION('',(0.E0,0.E0,1.E0)); -#1325=VECTOR('',#1324,6.E-1); -#1326=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.4035E1)); -#1327=LINE('',#1326,#1325); -#1328=DIRECTION('',(1.E0,0.E0,0.E0)); -#1329=VECTOR('',#1328,3.5E-1); -#1330=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.4035E1)); -#1331=LINE('',#1330,#1329); -#1332=DIRECTION('',(0.E0,1.E0,0.E0)); -#1333=VECTOR('',#1332,5.E-2); -#1334=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1235E1)); -#1335=LINE('',#1334,#1333); -#1336=DIRECTION('',(0.E0,1.E0,0.E0)); -#1337=VECTOR('',#1336,5.E-2); -#1338=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1835E1)); -#1339=LINE('',#1338,#1337); -#1340=CARTESIAN_POINT('',(-7.55E0,-2.5E-1,-1.1535E1)); -#1341=DIRECTION('',(0.E0,1.E0,0.E0)); -#1342=DIRECTION('',(2.E-1,0.E0,9.797958971133E-1)); -#1343=AXIS2_PLACEMENT_3D('',#1340,#1341,#1342); -#1345=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.1535E1)); -#1346=DIRECTION('',(0.E0,-1.E0,0.E0)); -#1347=DIRECTION('',(2.E-1,0.E0,-9.797958971133E-1)); -#1348=AXIS2_PLACEMENT_3D('',#1345,#1346,#1347); -#1350=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1351=VECTOR('',#1350,5.380931551418E0); -#1352=CARTESIAN_POINT('',(6.8E0,3.E-1,1.342E1)); -#1353=LINE('',#1352,#1351); -#1354=DIRECTION('',(1.E0,0.E0,0.E0)); -#1355=VECTOR('',#1354,1.5E-1); -#1356=CARTESIAN_POINT('',(6.65E0,3.E-1,8.039068448582E0)); -#1357=LINE('',#1356,#1355); -#1358=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1359=VECTOR('',#1358,5.230931551418E0); -#1360=CARTESIAN_POINT('',(6.65E0,3.E-1,1.327E1)); -#1361=LINE('',#1360,#1359); -#1362=DIRECTION('',(1.E0,0.E0,0.E0)); -#1363=VECTOR('',#1362,6.14E0); -#1364=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.327E1)); -#1365=LINE('',#1364,#1363); -#1366=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1367=VECTOR('',#1366,1.5E-1); -#1368=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.342E1)); -#1369=LINE('',#1368,#1367); -#1370=DIRECTION('',(1.E0,0.E0,0.E0)); -#1371=VECTOR('',#1370,6.29E0); -#1372=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.342E1)); -#1373=LINE('',#1372,#1371); -#1374=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1375=VECTOR('',#1374,4.723430313755E0); -#1376=CARTESIAN_POINT('',(6.8E0,3.E-1,5.639068448582E0)); -#1377=LINE('',#1376,#1375); -#1378=DIRECTION('',(1.E0,0.E0,0.E0)); -#1379=VECTOR('',#1378,1.5E-1); -#1380=CARTESIAN_POINT('',(6.65E0,3.E-1,9.156381348264E-1)); -#1381=LINE('',#1380,#1379); -#1382=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1383=VECTOR('',#1382,4.723430313755E0); -#1384=CARTESIAN_POINT('',(6.65E0,3.E-1,5.639068448582E0)); -#1385=LINE('',#1384,#1383); -#1386=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1387=VECTOR('',#1386,1.5E-1); -#1388=CARTESIAN_POINT('',(6.8E0,3.E-1,5.639068448582E0)); -#1389=LINE('',#1388,#1387); -#1390=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1391=VECTOR('',#1390,1.495638134826E0); -#1392=CARTESIAN_POINT('',(6.8E0,3.E-1,-8.436186517363E-2)); -#1393=LINE('',#1392,#1391); -#1394=DIRECTION('',(1.E0,0.E0,0.E0)); -#1395=VECTOR('',#1394,1.5E-1); -#1396=CARTESIAN_POINT('',(6.65E0,3.E-1,-1.58E0)); -#1397=LINE('',#1396,#1395); -#1398=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1399=VECTOR('',#1398,1.495638134826E0); -#1400=CARTESIAN_POINT('',(6.65E0,3.E-1,-8.436186517363E-2)); -#1401=LINE('',#1400,#1399); -#1402=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1403=VECTOR('',#1402,1.5E-1); -#1404=CARTESIAN_POINT('',(6.8E0,3.E-1,-8.436186517363E-2)); -#1405=LINE('',#1404,#1403); -#1406=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1407=VECTOR('',#1406,4.5E0); -#1408=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.98E0)); -#1409=LINE('',#1408,#1407); -#1410=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1411=VECTOR('',#1410,1.5E-1); -#1412=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.83E0)); -#1413=LINE('',#1412,#1411); -#1414=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1415=VECTOR('',#1414,4.5E0); -#1416=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.83E0)); -#1417=LINE('',#1416,#1415); -#1418=DIRECTION('',(0.E0,0.E0,1.E0)); -#1419=VECTOR('',#1418,1.5E-1); -#1420=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.98E0)); -#1421=LINE('',#1420,#1419); -#1422=DIRECTION('',(0.E0,0.E0,1.E0)); -#1423=VECTOR('',#1422,3.253367834275E0); -#1424=CARTESIAN_POINT('',(-5.4E0,3.E-1,-3.98E0)); -#1425=LINE('',#1424,#1423); -#1426=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1427=VECTOR('',#1426,1.5E-1); -#1428=CARTESIAN_POINT('',(-5.25E0,3.E-1,-7.266321657252E-1)); -#1429=LINE('',#1428,#1427); -#1430=DIRECTION('',(0.E0,0.E0,1.E0)); -#1431=VECTOR('',#1430,3.103367834275E0); -#1432=CARTESIAN_POINT('',(-5.25E0,3.E-1,-3.83E0)); -#1433=LINE('',#1432,#1431); -#1434=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1435=VECTOR('',#1434,5.2E0); -#1436=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.83E0)); -#1437=LINE('',#1436,#1435); -#1438=DIRECTION('',(0.E0,0.E0,1.E0)); -#1439=VECTOR('',#1438,1.5E-1); -#1440=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.98E0)); -#1441=LINE('',#1440,#1439); -#1442=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1443=VECTOR('',#1442,5.35E0); -#1444=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.98E0)); -#1445=LINE('',#1444,#1443); -#1446=DIRECTION('',(0.E0,0.E0,1.E0)); -#1447=VECTOR('',#1446,5.998212500813E0); -#1448=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.628565170500E-1)); -#1449=LINE('',#1448,#1447); -#1450=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1451=VECTOR('',#1450,1.5E-1); -#1452=CARTESIAN_POINT('',(-5.25E0,3.E-1,6.861069017863E0)); -#1453=LINE('',#1452,#1451); -#1454=DIRECTION('',(0.E0,0.E0,1.E0)); -#1455=VECTOR('',#1454,5.998212500813E0); -#1456=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.628565170500E-1)); -#1457=LINE('',#1456,#1455); -#1458=DIRECTION('',(1.E0,0.E0,0.E0)); -#1459=VECTOR('',#1458,1.5E-1); -#1460=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.628565170500E-1)); -#1461=LINE('',#1460,#1459); -#1462=DIRECTION('',(1.E0,0.E0,0.E0)); -#1463=VECTOR('',#1462,4.91E0); -#1464=CARTESIAN_POINT('',(-5.4E0,3.E-1,1.342E1)); -#1465=LINE('',#1464,#1463); -#1466=DIRECTION('',(0.E0,0.E0,1.E0)); -#1467=VECTOR('',#1466,1.5E-1); -#1468=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.327E1)); -#1469=LINE('',#1468,#1467); -#1470=DIRECTION('',(1.E0,0.E0,0.E0)); -#1471=VECTOR('',#1470,4.76E0); -#1472=CARTESIAN_POINT('',(-5.25E0,3.E-1,1.327E1)); -#1473=LINE('',#1472,#1471); -#1474=DIRECTION('',(0.E0,0.E0,1.E0)); -#1475=VECTOR('',#1474,4.512381985644E0); -#1476=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.757618014356E0)); -#1477=LINE('',#1476,#1475); -#1478=DIRECTION('',(1.E0,0.E0,0.E0)); -#1479=VECTOR('',#1478,1.5E-1); -#1480=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.757618014356E0)); -#1481=LINE('',#1480,#1479); -#1482=DIRECTION('',(0.E0,0.E0,1.E0)); -#1483=VECTOR('',#1482,4.662381985644E0); -#1484=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.757618014356E0)); -#1485=LINE('',#1484,#1483); -#1486=DIRECTION('',(0.E0,0.E0,1.E0)); -#1487=VECTOR('',#1486,3.200510257217E-1); -#1488=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.43E1)); -#1489=LINE('',#1488,#1487); -#1490=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1491=VECTOR('',#1490,1.5E1); -#1492=CARTESIAN_POINT('',(7.5E0,3.E-1,-1.43E1)); -#1493=LINE('',#1492,#1491); -#1494=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1495=VECTOR('',#1494,1.885E1); -#1496=CARTESIAN_POINT('',(7.5E0,3.E-1,4.55E0)); -#1497=LINE('',#1496,#1495); -#1498=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1499=VECTOR('',#1498,6.E-1); -#1500=CARTESIAN_POINT('',(7.5E0,3.E-1,4.55E0)); -#1501=LINE('',#1500,#1499); -#1502=DIRECTION('',(0.E0,0.E0,1.E0)); -#1503=VECTOR('',#1502,7.E-1); -#1504=CARTESIAN_POINT('',(6.9E0,3.E-1,4.55E0)); -#1505=LINE('',#1504,#1503); -#1506=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1507=VECTOR('',#1506,6.E-1); -#1508=CARTESIAN_POINT('',(7.5E0,3.E-1,5.25E0)); -#1509=LINE('',#1508,#1507); -#1510=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1511=VECTOR('',#1510,4.E-1); -#1512=CARTESIAN_POINT('',(7.5E0,3.E-1,5.65E0)); -#1513=LINE('',#1512,#1511); -#1514=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1515=VECTOR('',#1514,6.E-1); -#1516=CARTESIAN_POINT('',(7.5E0,3.E-1,5.65E0)); -#1517=LINE('',#1516,#1515); -#1518=DIRECTION('',(0.E0,0.E0,1.E0)); -#1519=VECTOR('',#1518,7.E-1); -#1520=CARTESIAN_POINT('',(6.9E0,3.E-1,5.65E0)); -#1521=LINE('',#1520,#1519); -#1522=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1523=VECTOR('',#1522,6.E-1); -#1524=CARTESIAN_POINT('',(7.5E0,3.E-1,6.35E0)); -#1525=LINE('',#1524,#1523); -#1526=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1527=VECTOR('',#1526,4.E-1); -#1528=CARTESIAN_POINT('',(7.5E0,3.E-1,6.75E0)); -#1529=LINE('',#1528,#1527); -#1530=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1531=VECTOR('',#1530,6.E-1); -#1532=CARTESIAN_POINT('',(7.5E0,3.E-1,6.75E0)); -#1533=LINE('',#1532,#1531); -#1534=DIRECTION('',(0.E0,0.E0,1.E0)); -#1535=VECTOR('',#1534,7.E-1); -#1536=CARTESIAN_POINT('',(6.9E0,3.E-1,6.75E0)); -#1537=LINE('',#1536,#1535); -#1538=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1539=VECTOR('',#1538,6.E-1); -#1540=CARTESIAN_POINT('',(7.5E0,3.E-1,7.45E0)); -#1541=LINE('',#1540,#1539); -#1542=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1543=VECTOR('',#1542,4.E-1); -#1544=CARTESIAN_POINT('',(7.5E0,3.E-1,7.85E0)); -#1545=LINE('',#1544,#1543); -#1546=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1547=VECTOR('',#1546,6.E-1); -#1548=CARTESIAN_POINT('',(7.5E0,3.E-1,7.85E0)); -#1549=LINE('',#1548,#1547); -#1550=DIRECTION('',(0.E0,0.E0,1.E0)); -#1551=VECTOR('',#1550,7.E-1); -#1552=CARTESIAN_POINT('',(6.9E0,3.E-1,7.85E0)); -#1553=LINE('',#1552,#1551); -#1554=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1555=VECTOR('',#1554,6.E-1); -#1556=CARTESIAN_POINT('',(7.5E0,3.E-1,8.55E0)); -#1557=LINE('',#1556,#1555); -#1558=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1559=VECTOR('',#1558,4.E-1); -#1560=CARTESIAN_POINT('',(7.5E0,3.E-1,8.95E0)); -#1561=LINE('',#1560,#1559); -#1562=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1563=VECTOR('',#1562,6.E-1); -#1564=CARTESIAN_POINT('',(7.5E0,3.E-1,8.95E0)); -#1565=LINE('',#1564,#1563); -#1566=DIRECTION('',(0.E0,0.E0,1.E0)); -#1567=VECTOR('',#1566,7.E-1); -#1568=CARTESIAN_POINT('',(6.9E0,3.E-1,8.95E0)); -#1569=LINE('',#1568,#1567); -#1570=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1571=VECTOR('',#1570,6.E-1); -#1572=CARTESIAN_POINT('',(7.5E0,3.E-1,9.65E0)); -#1573=LINE('',#1572,#1571); -#1574=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1575=VECTOR('',#1574,4.E-1); -#1576=CARTESIAN_POINT('',(7.5E0,3.E-1,1.005E1)); -#1577=LINE('',#1576,#1575); -#1578=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1579=VECTOR('',#1578,6.E-1); -#1580=CARTESIAN_POINT('',(7.5E0,3.E-1,1.005E1)); -#1581=LINE('',#1580,#1579); -#1582=DIRECTION('',(0.E0,0.E0,1.E0)); -#1583=VECTOR('',#1582,7.E-1); -#1584=CARTESIAN_POINT('',(6.9E0,3.E-1,1.005E1)); -#1585=LINE('',#1584,#1583); -#1586=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1587=VECTOR('',#1586,6.E-1); -#1588=CARTESIAN_POINT('',(7.5E0,3.E-1,1.075E1)); -#1589=LINE('',#1588,#1587); -#1590=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1591=VECTOR('',#1590,4.E-1); -#1592=CARTESIAN_POINT('',(7.5E0,3.E-1,1.115E1)); -#1593=LINE('',#1592,#1591); -#1594=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1595=VECTOR('',#1594,6.E-1); -#1596=CARTESIAN_POINT('',(7.5E0,3.E-1,1.115E1)); -#1597=LINE('',#1596,#1595); -#1598=DIRECTION('',(0.E0,0.E0,1.E0)); -#1599=VECTOR('',#1598,7.E-1); -#1600=CARTESIAN_POINT('',(6.9E0,3.E-1,1.115E1)); -#1601=LINE('',#1600,#1599); -#1602=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1603=VECTOR('',#1602,6.E-1); -#1604=CARTESIAN_POINT('',(7.5E0,3.E-1,1.185E1)); -#1605=LINE('',#1604,#1603); -#1606=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1607=VECTOR('',#1606,4.E-1); -#1608=CARTESIAN_POINT('',(7.5E0,3.E-1,1.225E1)); -#1609=LINE('',#1608,#1607); -#1610=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1611=VECTOR('',#1610,6.E-1); -#1612=CARTESIAN_POINT('',(7.5E0,3.E-1,1.225E1)); -#1613=LINE('',#1612,#1611); -#1614=DIRECTION('',(0.E0,0.E0,1.E0)); -#1615=VECTOR('',#1614,7.E-1); -#1616=CARTESIAN_POINT('',(6.9E0,3.E-1,1.225E1)); -#1617=LINE('',#1616,#1615); -#1618=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1619=VECTOR('',#1618,6.E-1); -#1620=CARTESIAN_POINT('',(7.5E0,3.E-1,1.295E1)); -#1621=LINE('',#1620,#1619); -#1622=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1623=VECTOR('',#1622,7.5E-1); -#1624=CARTESIAN_POINT('',(7.5E0,3.E-1,1.37E1)); -#1625=LINE('',#1624,#1623); -#1626=DIRECTION('',(1.E0,0.E0,0.E0)); -#1627=VECTOR('',#1626,1.4E1); -#1628=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.37E1)); -#1629=LINE('',#1628,#1627); -#1630=DIRECTION('',(0.E0,0.E0,1.E0)); -#1631=VECTOR('',#1630,7.5E-1); -#1632=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.295E1)); -#1633=LINE('',#1632,#1631); -#1634=DIRECTION('',(1.E0,0.E0,0.E0)); -#1635=VECTOR('',#1634,6.E-1); -#1636=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.295E1)); -#1637=LINE('',#1636,#1635); -#1638=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1639=VECTOR('',#1638,7.E-1); -#1640=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.295E1)); -#1641=LINE('',#1640,#1639); -#1642=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1643=VECTOR('',#1642,6.E-1); -#1644=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.225E1)); -#1645=LINE('',#1644,#1643); -#1646=DIRECTION('',(0.E0,0.E0,1.E0)); -#1647=VECTOR('',#1646,4.E-1); -#1648=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.185E1)); -#1649=LINE('',#1648,#1647); -#1650=DIRECTION('',(1.E0,0.E0,0.E0)); -#1651=VECTOR('',#1650,6.E-1); -#1652=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.185E1)); -#1653=LINE('',#1652,#1651); -#1654=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1655=VECTOR('',#1654,7.E-1); -#1656=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.185E1)); -#1657=LINE('',#1656,#1655); -#1658=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1659=VECTOR('',#1658,6.E-1); -#1660=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.115E1)); -#1661=LINE('',#1660,#1659); -#1662=DIRECTION('',(0.E0,0.E0,1.E0)); -#1663=VECTOR('',#1662,4.E-1); -#1664=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.075E1)); -#1665=LINE('',#1664,#1663); -#1666=DIRECTION('',(1.E0,0.E0,0.E0)); -#1667=VECTOR('',#1666,6.E-1); -#1668=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.075E1)); -#1669=LINE('',#1668,#1667); -#1670=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1671=VECTOR('',#1670,7.E-1); -#1672=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.075E1)); -#1673=LINE('',#1672,#1671); -#1674=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1675=VECTOR('',#1674,6.E-1); -#1676=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.005E1)); -#1677=LINE('',#1676,#1675); -#1678=DIRECTION('',(0.E0,0.E0,1.E0)); -#1679=VECTOR('',#1678,4.E-1); -#1680=CARTESIAN_POINT('',(-6.5E0,3.E-1,9.65E0)); -#1681=LINE('',#1680,#1679); -#1682=DIRECTION('',(1.E0,0.E0,0.E0)); -#1683=VECTOR('',#1682,6.E-1); -#1684=CARTESIAN_POINT('',(-6.5E0,3.E-1,9.65E0)); -#1685=LINE('',#1684,#1683); -#1686=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1687=VECTOR('',#1686,7.E-1); -#1688=CARTESIAN_POINT('',(-5.9E0,3.E-1,9.65E0)); -#1689=LINE('',#1688,#1687); -#1690=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1691=VECTOR('',#1690,6.E-1); -#1692=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.95E0)); -#1693=LINE('',#1692,#1691); -#1694=DIRECTION('',(0.E0,0.E0,1.E0)); -#1695=VECTOR('',#1694,4.E-1); -#1696=CARTESIAN_POINT('',(-6.5E0,3.E-1,8.55E0)); -#1697=LINE('',#1696,#1695); -#1698=DIRECTION('',(1.E0,0.E0,0.E0)); -#1699=VECTOR('',#1698,6.E-1); -#1700=CARTESIAN_POINT('',(-6.5E0,3.E-1,8.55E0)); -#1701=LINE('',#1700,#1699); -#1702=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1703=VECTOR('',#1702,7.E-1); -#1704=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.55E0)); -#1705=LINE('',#1704,#1703); -#1706=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1707=VECTOR('',#1706,6.E-1); -#1708=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.85E0)); -#1709=LINE('',#1708,#1707); -#1710=DIRECTION('',(0.E0,0.E0,1.E0)); -#1711=VECTOR('',#1710,4.E-1); -#1712=CARTESIAN_POINT('',(-6.5E0,3.E-1,7.45E0)); -#1713=LINE('',#1712,#1711); -#1714=DIRECTION('',(1.E0,0.E0,0.E0)); -#1715=VECTOR('',#1714,6.E-1); -#1716=CARTESIAN_POINT('',(-6.5E0,3.E-1,7.45E0)); -#1717=LINE('',#1716,#1715); -#1718=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1719=VECTOR('',#1718,7.E-1); -#1720=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.45E0)); -#1721=LINE('',#1720,#1719); -#1722=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1723=VECTOR('',#1722,6.E-1); -#1724=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.75E0)); -#1725=LINE('',#1724,#1723); -#1726=DIRECTION('',(0.E0,0.E0,1.E0)); -#1727=VECTOR('',#1726,4.E-1); -#1728=CARTESIAN_POINT('',(-6.5E0,3.E-1,6.35E0)); -#1729=LINE('',#1728,#1727); -#1730=DIRECTION('',(1.E0,0.E0,0.E0)); -#1731=VECTOR('',#1730,6.E-1); -#1732=CARTESIAN_POINT('',(-6.5E0,3.E-1,6.35E0)); -#1733=LINE('',#1732,#1731); -#1734=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1735=VECTOR('',#1734,7.E-1); -#1736=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.35E0)); -#1737=LINE('',#1736,#1735); -#1738=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1739=VECTOR('',#1738,6.E-1); -#1740=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.65E0)); -#1741=LINE('',#1740,#1739); -#1742=DIRECTION('',(0.E0,0.E0,1.E0)); -#1743=VECTOR('',#1742,4.E-1); -#1744=CARTESIAN_POINT('',(-6.5E0,3.E-1,5.25E0)); -#1745=LINE('',#1744,#1743); -#1746=DIRECTION('',(1.E0,0.E0,0.E0)); -#1747=VECTOR('',#1746,6.E-1); -#1748=CARTESIAN_POINT('',(-6.5E0,3.E-1,5.25E0)); -#1749=LINE('',#1748,#1747); -#1750=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1751=VECTOR('',#1750,7.E-1); -#1752=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.25E0)); -#1753=LINE('',#1752,#1751); -#1754=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1755=VECTOR('',#1754,6.E-1); -#1756=CARTESIAN_POINT('',(-5.9E0,3.E-1,4.55E0)); -#1757=LINE('',#1756,#1755); -#1758=DIRECTION('',(0.E0,0.E0,1.E0)); -#1759=VECTOR('',#1758,3.55E0); -#1760=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.E0)); -#1761=LINE('',#1760,#1759); -#1762=DIRECTION('',(1.E0,0.E0,0.E0)); -#1763=VECTOR('',#1762,1.E0); -#1764=CARTESIAN_POINT('',(-7.5E0,3.E-1,1.E0)); -#1765=LINE('',#1764,#1763); -#1766=DIRECTION('',(0.E0,0.E0,1.E0)); -#1767=VECTOR('',#1766,1.229005102572E1); -#1768=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.129005102572E1)); -#1769=LINE('',#1768,#1767); -#1770=DIRECTION('',(0.E0,0.E0,1.E0)); -#1771=VECTOR('',#1770,6.101020514434E-1); -#1772=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.239005102572E1)); -#1773=LINE('',#1772,#1771); -#1774=DIRECTION('',(0.E0,0.E0,1.E0)); -#1775=VECTOR('',#1774,6.101020514434E-1); -#1776=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.349005102572E1)); -#1777=LINE('',#1776,#1775); -#1778=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1779=VECTOR('',#1778,2.4E0); -#1780=CARTESIAN_POINT('',(6.8E0,1.4E0,8.039068448582E0)); -#1781=LINE('',#1780,#1779); -#1782=DIRECTION('',(0.E0,1.E0,0.E0)); -#1783=VECTOR('',#1782,1.1E0); -#1784=CARTESIAN_POINT('',(6.8E0,3.E-1,8.039068448582E0)); -#1785=LINE('',#1784,#1783); -#1786=DIRECTION('',(0.E0,1.E0,0.E0)); -#1787=VECTOR('',#1786,1.25E0); -#1788=CARTESIAN_POINT('',(6.8E0,3.E-1,1.342E1)); -#1789=LINE('',#1788,#1787); -#1790=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1791=VECTOR('',#1790,2.4E0); -#1792=CARTESIAN_POINT('',(6.8E0,1.4E0,-1.58E0)); -#1793=LINE('',#1792,#1791); -#1794=DIRECTION('',(0.E0,1.E0,0.E0)); -#1795=VECTOR('',#1794,1.1E0); -#1796=CARTESIAN_POINT('',(6.8E0,3.E-1,-1.58E0)); -#1797=LINE('',#1796,#1795); -#1798=DIRECTION('',(0.E0,1.E0,0.E0)); -#1799=VECTOR('',#1798,1.1E0); -#1800=CARTESIAN_POINT('',(6.8E0,3.E-1,-8.436186517363E-2)); -#1801=LINE('',#1800,#1799); -#1802=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1803=VECTOR('',#1802,1.E0); -#1804=CARTESIAN_POINT('',(6.8E0,1.4E0,9.156381348264E-1)); -#1805=LINE('',#1804,#1803); -#1806=DIRECTION('',(0.E0,1.E0,0.E0)); -#1807=VECTOR('',#1806,1.1E0); -#1808=CARTESIAN_POINT('',(6.8E0,3.E-1,9.156381348264E-1)); -#1809=LINE('',#1808,#1807); -#1810=DIRECTION('',(0.E0,1.E0,0.E0)); -#1811=VECTOR('',#1810,1.1E0); -#1812=CARTESIAN_POINT('',(6.8E0,3.E-1,5.639068448582E0)); -#1813=LINE('',#1812,#1811); -#1814=DIRECTION('',(1.E0,0.E0,0.E0)); -#1815=VECTOR('',#1814,1.5E-1); -#1816=CARTESIAN_POINT('',(-5.4E0,1.4E0,8.628565170500E-1)); -#1817=LINE('',#1816,#1815); -#1818=DIRECTION('',(0.E0,0.E0,1.E0)); -#1819=VECTOR('',#1818,5.998212500813E0); -#1820=CARTESIAN_POINT('',(-5.25E0,1.4E0,8.628565170500E-1)); -#1821=LINE('',#1820,#1819); -#1822=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1823=VECTOR('',#1822,1.5E-1); -#1824=CARTESIAN_POINT('',(-5.25E0,1.4E0,6.861069017863E0)); -#1825=LINE('',#1824,#1823); -#1826=DIRECTION('',(1.E0,0.E0,0.E0)); -#1827=VECTOR('',#1826,1.5E-1); -#1828=CARTESIAN_POINT('',(-5.4E0,1.4E0,8.757618014356E0)); -#1829=LINE('',#1828,#1827); -#1830=DIRECTION('',(0.E0,0.E0,1.E0)); -#1831=VECTOR('',#1830,4.512381985644E0); -#1832=CARTESIAN_POINT('',(-5.25E0,1.4E0,8.757618014356E0)); -#1833=LINE('',#1832,#1831); -#1834=DIRECTION('',(1.E0,0.E0,0.E0)); -#1835=VECTOR('',#1834,4.76E0); -#1836=CARTESIAN_POINT('',(-5.25E0,1.4E0,1.327E1)); -#1837=LINE('',#1836,#1835); -#1838=DIRECTION('',(0.E0,0.E0,1.E0)); -#1839=VECTOR('',#1838,1.5E-1); -#1840=CARTESIAN_POINT('',(-4.9E-1,1.4E0,1.327E1)); -#1841=LINE('',#1840,#1839); -#1842=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1843=VECTOR('',#1842,1.5E-1); -#1844=CARTESIAN_POINT('',(5.1E-1,1.4E0,1.342E1)); -#1845=LINE('',#1844,#1843); -#1846=DIRECTION('',(1.E0,0.E0,0.E0)); -#1847=VECTOR('',#1846,6.14E0); -#1848=CARTESIAN_POINT('',(5.1E-1,1.4E0,1.327E1)); -#1849=LINE('',#1848,#1847); -#1850=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1851=VECTOR('',#1850,5.230931551418E0); -#1852=CARTESIAN_POINT('',(6.65E0,1.4E0,1.327E1)); -#1853=LINE('',#1852,#1851); -#1854=DIRECTION('',(1.E0,0.E0,0.E0)); -#1855=VECTOR('',#1854,1.5E-1); -#1856=CARTESIAN_POINT('',(6.65E0,1.4E0,8.039068448582E0)); -#1857=LINE('',#1856,#1855); -#1858=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1859=VECTOR('',#1858,1.5E-1); -#1860=CARTESIAN_POINT('',(6.8E0,1.4E0,5.639068448582E0)); -#1861=LINE('',#1860,#1859); -#1862=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1863=VECTOR('',#1862,4.723430313755E0); -#1864=CARTESIAN_POINT('',(6.65E0,1.4E0,5.639068448582E0)); -#1865=LINE('',#1864,#1863); -#1866=DIRECTION('',(1.E0,0.E0,0.E0)); -#1867=VECTOR('',#1866,1.5E-1); -#1868=CARTESIAN_POINT('',(6.65E0,1.4E0,9.156381348264E-1)); -#1869=LINE('',#1868,#1867); -#1870=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1871=VECTOR('',#1870,1.5E-1); -#1872=CARTESIAN_POINT('',(6.8E0,1.4E0,-8.436186517363E-2)); -#1873=LINE('',#1872,#1871); -#1874=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1875=VECTOR('',#1874,1.495638134826E0); -#1876=CARTESIAN_POINT('',(6.65E0,1.4E0,-8.436186517363E-2)); -#1877=LINE('',#1876,#1875); -#1878=DIRECTION('',(1.E0,0.E0,0.E0)); -#1879=VECTOR('',#1878,1.5E-1); -#1880=CARTESIAN_POINT('',(6.65E0,1.4E0,-1.58E0)); -#1881=LINE('',#1880,#1879); -#1882=DIRECTION('',(0.E0,0.E0,1.E0)); -#1883=VECTOR('',#1882,1.5E-1); -#1884=CARTESIAN_POINT('',(5.1E0,1.4E0,-3.98E0)); -#1885=LINE('',#1884,#1883); -#1886=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1887=VECTOR('',#1886,4.5E0); -#1888=CARTESIAN_POINT('',(5.1E0,1.4E0,-3.83E0)); -#1889=LINE('',#1888,#1887); -#1890=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1891=VECTOR('',#1890,1.5E-1); -#1892=CARTESIAN_POINT('',(6.E-1,1.4E0,-3.83E0)); -#1893=LINE('',#1892,#1891); -#1894=DIRECTION('',(0.E0,0.E0,1.E0)); -#1895=VECTOR('',#1894,1.5E-1); -#1896=CARTESIAN_POINT('',(-5.E-2,1.4E0,-3.98E0)); -#1897=LINE('',#1896,#1895); -#1898=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1899=VECTOR('',#1898,5.2E0); -#1900=CARTESIAN_POINT('',(-5.E-2,1.4E0,-3.83E0)); -#1901=LINE('',#1900,#1899); -#1902=DIRECTION('',(0.E0,0.E0,1.E0)); -#1903=VECTOR('',#1902,3.103367834275E0); -#1904=CARTESIAN_POINT('',(-5.25E0,1.4E0,-3.83E0)); -#1905=LINE('',#1904,#1903); -#1906=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1907=VECTOR('',#1906,1.5E-1); -#1908=CARTESIAN_POINT('',(-5.25E0,1.4E0,-7.266321657252E-1)); -#1909=LINE('',#1908,#1907); -#1910=DIRECTION('',(0.E0,0.E0,1.E0)); -#1911=VECTOR('',#1910,1.589488682775E0); -#1912=CARTESIAN_POINT('',(-5.4E0,1.4E0,-7.266321657252E-1)); -#1913=LINE('',#1912,#1911); -#1914=DIRECTION('',(0.E0,1.E0,0.E0)); -#1915=VECTOR('',#1914,1.1E0); -#1916=CARTESIAN_POINT('',(-5.4E0,3.E-1,-7.266321657252E-1)); -#1917=LINE('',#1916,#1915); -#1918=DIRECTION('',(0.E0,1.E0,0.E0)); -#1919=VECTOR('',#1918,1.25E0); -#1920=CARTESIAN_POINT('',(-5.4E0,3.E-1,-3.98E0)); -#1921=LINE('',#1920,#1919); -#1922=DIRECTION('',(0.E0,1.E0,0.E0)); -#1923=VECTOR('',#1922,1.1E0); -#1924=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.757618014356E0)); -#1925=LINE('',#1924,#1923); -#1926=DIRECTION('',(0.E0,0.E0,1.E0)); -#1927=VECTOR('',#1926,1.896548996493E0); -#1928=CARTESIAN_POINT('',(-5.4E0,1.4E0,6.861069017863E0)); -#1929=LINE('',#1928,#1927); -#1930=DIRECTION('',(0.E0,1.E0,0.E0)); -#1931=VECTOR('',#1930,1.1E0); -#1932=CARTESIAN_POINT('',(-5.4E0,3.E-1,6.861069017863E0)); -#1933=LINE('',#1932,#1931); -#1934=DIRECTION('',(0.E0,1.E0,0.E0)); -#1935=VECTOR('',#1934,1.1E0); -#1936=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.628565170500E-1)); -#1937=LINE('',#1936,#1935); -#1938=DIRECTION('',(0.E0,1.E0,0.E0)); -#1939=VECTOR('',#1938,1.1E0); -#1940=CARTESIAN_POINT('',(-5.25E0,3.E-1,-7.266321657252E-1)); -#1941=LINE('',#1940,#1939); -#1942=DIRECTION('',(0.E0,1.E0,0.E0)); -#1943=VECTOR('',#1942,1.1E0); -#1944=CARTESIAN_POINT('',(-5.25E0,3.E-1,-3.83E0)); -#1945=LINE('',#1944,#1943); -#1946=DIRECTION('',(0.E0,1.E0,0.E0)); -#1947=VECTOR('',#1946,1.1E0); -#1948=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.83E0)); -#1949=LINE('',#1948,#1947); -#1950=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1951=VECTOR('',#1950,1.7E0); -#1952=CARTESIAN_POINT('',(6.8E0,1.4E0,-3.98E0)); -#1953=LINE('',#1952,#1951); -#1954=DIRECTION('',(0.E0,1.E0,0.E0)); -#1955=VECTOR('',#1954,1.5E-1); -#1956=CARTESIAN_POINT('',(6.8E0,1.4E0,-3.98E0)); -#1957=LINE('',#1956,#1955); -#1958=DIRECTION('',(0.E0,1.E0,0.E0)); -#1959=VECTOR('',#1958,1.1E0); -#1960=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.98E0)); -#1961=LINE('',#1960,#1959); -#1962=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1963=VECTOR('',#1962,6.5E-1); -#1964=CARTESIAN_POINT('',(6.E-1,1.4E0,-3.98E0)); -#1965=LINE('',#1964,#1963); -#1966=DIRECTION('',(0.E0,1.E0,0.E0)); -#1967=VECTOR('',#1966,1.1E0); -#1968=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.98E0)); -#1969=LINE('',#1968,#1967); -#1970=DIRECTION('',(0.E0,1.E0,0.E0)); -#1971=VECTOR('',#1970,1.1E0); -#1972=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.98E0)); -#1973=LINE('',#1972,#1971); -#1974=DIRECTION('',(0.E0,0.E0,-1.E0)); -#1975=VECTOR('',#1974,1.74E1); -#1976=CARTESIAN_POINT('',(-5.4E0,1.55E0,1.342E1)); -#1977=LINE('',#1976,#1975); -#1978=DIRECTION('',(1.E0,0.E0,0.E0)); -#1979=VECTOR('',#1978,1.22E1); -#1980=CARTESIAN_POINT('',(-5.4E0,1.55E0,-3.98E0)); -#1981=LINE('',#1980,#1979); -#1982=DIRECTION('',(0.E0,0.E0,1.E0)); -#1983=VECTOR('',#1982,1.74E1); -#1984=CARTESIAN_POINT('',(6.8E0,1.55E0,-3.98E0)); -#1985=LINE('',#1984,#1983); -#1986=DIRECTION('',(-1.E0,0.E0,0.E0)); -#1987=VECTOR('',#1986,1.22E1); -#1988=CARTESIAN_POINT('',(6.8E0,1.55E0,1.342E1)); -#1989=LINE('',#1988,#1987); -#1990=DIRECTION('',(-6.026976445372E-1,0.E0,-7.979696418218E-1)); -#1991=VECTOR('',#1990,7.060453413469E-2); -#1992=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,8.126726183650E0)); -#1993=LINE('',#1992,#1991); -#1994=DIRECTION('',(-8.956781608936E-1,0.E0,-4.447028582079E-1)); -#1995=VECTOR('',#1994,1.900378429420E-1); -#1996=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,8.070385908836E0)); -#1997=LINE('',#1996,#1995); -#1998=DIRECTION('',(-9.765078408199E-1,0.E0,-2.154818712031E-1)); -#1999=VECTOR('',#1998,1.307307058003E-1); -#2000=CARTESIAN_POINT('',(7.659574747086E-1,1.55E0,7.985875536912E0)); -#2001=LINE('',#2000,#1999); -#2002=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2003=VECTOR('',#2002,1.702128648758E-1); -#2004=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,7.957705439802E0)); -#2005=LINE('',#2004,#2003); -#2006=DIRECTION('',(-9.765078408199E-1,0.E0,2.154818712031E-1)); -#2007=VECTOR('',#2006,1.307307058003E-1); -#2008=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,7.957705439802E0)); -#2009=LINE('',#2008,#2007); -#2010=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#2011=VECTOR('',#2010,1.900378429420E-1); -#2012=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,7.985875536912E0)); -#2013=LINE('',#2012,#2011); -#2014=DIRECTION('',(-7.497222295638E-1,0.E0,6.617526565854E-1)); -#2015=VECTOR('',#2014,1.702758091142E-1); -#2016=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,8.070385908836E0)); -#2017=LINE('',#2016,#2015); -#2018=DIRECTION('',(-2.892053759356E-1,0.E0,9.572670737730E-1)); -#2019=VECTOR('',#2018,1.471382967172E-1); -#2020=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,8.183066377870E0)); -#2021=LINE('',#2020,#2019); -#2022=DIRECTION('',(0.E0,0.E0,1.E0)); -#2023=VECTOR('',#2022,6.760829753920E-1); -#2024=CARTESIAN_POINT('',(0.E0,1.55E0,8.323917024608E0)); -#2025=LINE('',#2024,#2023); -#2026=DIRECTION('',(1.E0,0.E0,0.E0)); -#2027=VECTOR('',#2026,2.E0); -#2028=CARTESIAN_POINT('',(0.E0,1.55E0,9.E0)); -#2029=LINE('',#2028,#2027); -#2030=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2031=VECTOR('',#2030,6.760829753920E-1); -#2032=CARTESIAN_POINT('',(2.E0,1.55E0,9.E0)); -#2033=LINE('',#2032,#2031); -#2034=DIRECTION('',(-2.892053991362E-1,0.E0,-9.572670667637E-1)); -#2035=VECTOR('',#2034,1.471382977946E-1); -#2036=CARTESIAN_POINT('',(2.E0,1.55E0,8.323917024608E0)); -#2037=LINE('',#2036,#2035); -#2038=DIRECTION('',(-7.497222583060E-1,0.E0,-6.617526240224E-1)); -#2039=VECTOR('',#2038,1.702758174930E-1); -#2040=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,8.183066377870E0)); -#2041=LINE('',#2040,#2039); -#2042=DIRECTION('',(-8.956781764003E-1,0.E0,-4.447028269758E-1)); -#2043=VECTOR('',#2042,1.900378562887E-1); -#2044=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,8.070385908836E0)); -#2045=LINE('',#2044,#2043); -#2046=DIRECTION('',(-9.765078514050E-1,0.E0,-2.154818232343E-1)); -#2047=VECTOR('',#2046,1.307307349025E-1); -#2048=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,7.985875536912E0)); -#2049=LINE('',#2048,#2047); -#2050=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2051=VECTOR('',#2050,2.127659320831E-1); -#2052=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,7.957705439802E0)); -#2053=LINE('',#2052,#2051); -#2054=DIRECTION('',(-9.765078619901E-1,0.E0,2.154817752655E-1)); -#2055=VECTOR('',#2054,1.307307640047E-1); -#2056=CARTESIAN_POINT('',(1.319148957729E0,1.55E0,7.957705439802E0)); -#2057=LINE('',#2056,#2055); -#2058=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#2059=VECTOR('',#2058,1.900378429420E-1); -#2060=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,7.985875536912E0)); -#2061=LINE('',#2060,#2059); -#2062=DIRECTION('',(-6.026976445372E-1,0.E0,7.979696418218E-1)); -#2063=VECTOR('',#2062,7.060453413469E-2); -#2064=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,8.070385908836E0)); -#2065=LINE('',#2064,#2063); -#2066=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2067=VECTOR('',#2066,5.352323286535E-1); -#2068=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.830979256152E0)); -#2069=LINE('',#2068,#2067); -#2070=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#2071=VECTOR('',#2070,9.461911348634E-2); -#2072=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.295746927498E0)); -#2073=LINE('',#2072,#2071); -#2074=DIRECTION('',(8.338425497604E-1,0.E0,-5.520023570683E-1)); -#2075=VECTOR('',#2074,1.020652794196E-1); -#2076=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,8.211236555574E0)); -#2077=LINE('',#2076,#2075); -#2078=DIRECTION('',(9.765078831602E-1,0.E0,-2.154816793280E-1)); -#2079=VECTOR('',#2078,1.307308222091E-1); -#2080=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,8.154896280760E0)); -#2081=LINE('',#2080,#2079); -#2082=DIRECTION('',(1.E0,0.E0,0.E0)); -#2083=VECTOR('',#2082,8.510637283325E-2); -#2084=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,8.126726183650E0)); -#2085=LINE('',#2084,#2083); -#2086=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#2087=VECTOR('',#2086,1.307307058003E-1); -#2088=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,8.126726183650E0)); -#2089=LINE('',#2088,#2087); -#2090=DIRECTION('',(8.338425497604E-1,0.E0,5.520023570683E-1)); -#2091=VECTOR('',#2090,1.020652794196E-1); -#2092=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,8.154896280760E0)); -#2093=LINE('',#2092,#2091); -#2094=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#2095=VECTOR('',#2094,9.461911348634E-2); -#2096=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,8.211236555574E0)); -#2097=LINE('',#2096,#2095); -#2098=DIRECTION('',(0.E0,0.E0,1.E0)); -#2099=VECTOR('',#2098,5.352323286535E-1); -#2100=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.295746927498E0)); -#2101=LINE('',#2100,#2099); -#2102=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2103=VECTOR('',#2102,5.957447290421E-1); -#2104=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.830979256152E0)); -#2105=LINE('',#2104,#2103); -#2106=DIRECTION('',(1.E0,0.E0,0.E0)); -#2107=VECTOR('',#2106,1.276595592499E-1); -#2108=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,8.126726183650E0)); -#2109=LINE('',#2108,#2107); -#2110=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#2111=VECTOR('',#2110,1.307307058003E-1); -#2112=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,8.126726183650E0)); -#2113=LINE('',#2112,#2111); -#2114=DIRECTION('',(8.338426387325E-1,0.E0,5.520022226690E-1)); -#2115=VECTOR('',#2114,1.020653042700E-1); -#2116=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,8.154896280760E0)); -#2117=LINE('',#2116,#2115); -#2118=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#2119=VECTOR('',#2118,9.461911348634E-2); -#2120=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,8.211236555574E0)); -#2121=LINE('',#2120,#2119); -#2122=DIRECTION('',(0.E0,0.E0,1.E0)); -#2123=VECTOR('',#2122,5.352323286535E-1); -#2124=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.295746927498E0)); -#2125=LINE('',#2124,#2123); -#2126=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2127=VECTOR('',#2126,6.382978856564E-1); -#2128=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.830979256152E0)); -#2129=LINE('',#2128,#2127); -#2130=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2131=VECTOR('',#2130,5.352323286535E-1); -#2132=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.830979256152E0)); -#2133=LINE('',#2132,#2131); -#2134=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#2135=VECTOR('',#2134,9.461911348634E-2); -#2136=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.295746927498E0)); -#2137=LINE('',#2136,#2135); -#2138=DIRECTION('',(8.338425497604E-1,0.E0,-5.520023570683E-1)); -#2139=VECTOR('',#2138,1.020652794196E-1); -#2140=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,8.211236555574E0)); -#2141=LINE('',#2140,#2139); -#2142=DIRECTION('',(9.765078619901E-1,0.E0,-2.154817752655E-1)); -#2143=VECTOR('',#2142,1.307307640047E-1); -#2144=CARTESIAN_POINT('',(1.234042525291E0,1.55E0,8.154896280760E0)); -#2145=LINE('',#2144,#2143); -#2146=DIRECTION('',(0.E0,0.E0,1.E0)); -#2147=VECTOR('',#2146,1.070464657307E0); -#2148=CARTESIAN_POINT('',(0.E0,1.55E0,6.661879763833E0)); -#2149=LINE('',#2148,#2147); -#2150=DIRECTION('',(1.E0,0.E0,0.E0)); -#2151=VECTOR('',#2150,2.127659320831E-1); -#2152=CARTESIAN_POINT('',(0.E0,1.55E0,7.732344421140E0)); -#2153=LINE('',#2152,#2151); -#2154=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2155=VECTOR('',#2154,4.507220373249E-1); -#2156=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.732344421140E0)); -#2157=LINE('',#2156,#2155); -#2158=DIRECTION('',(1.E0,0.E0,0.E0)); -#2159=VECTOR('',#2158,1.787234067917E0); -#2160=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.281622383815E0)); -#2161=LINE('',#2160,#2159); -#2162=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2163=VECTOR('',#2162,1.690207438480E-1); -#2164=CARTESIAN_POINT('',(2.E0,1.55E0,7.281622383815E0)); -#2165=LINE('',#2164,#2163); -#2166=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2167=VECTOR('',#2166,1.787234067917E0); -#2168=CARTESIAN_POINT('',(2.E0,1.55E0,7.112601639967E0)); -#2169=LINE('',#2168,#2167); -#2170=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2171=VECTOR('',#2170,4.507218761342E-1); -#2172=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.112601639967E0)); -#2173=LINE('',#2172,#2171); -#2174=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2175=VECTOR('',#2174,2.127659320831E-1); -#2176=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,6.661879763833E0)); -#2177=LINE('',#2176,#2175); -#2178=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#2179=VECTOR('',#2178,7.060459844736E-2); -#2180=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,6.211157726508E0)); -#2181=LINE('',#2180,#2179); -#2182=DIRECTION('',(7.497224643937E-1,0.E0,6.617523905385E-1)); -#2183=VECTOR('',#2182,1.702757557800E-1); -#2184=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,6.267498081918E0)); -#2185=LINE('',#2184,#2183); -#2186=DIRECTION('',(9.666829879352E-1,0.E0,2.559765630612E-1)); -#2187=VECTOR('',#2186,2.200990338541E-1); -#2188=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,6.380178470356E0)); -#2189=LINE('',#2188,#2187); -#2190=DIRECTION('',(1.E0,0.E0,0.E0)); -#2191=VECTOR('',#2190,1.276595592499E-1); -#2192=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.436518664575E0)); -#2193=LINE('',#2192,#2191); -#2194=DIRECTION('',(9.666829790630E-1,0.E0,-2.559765965668E-1)); -#2195=VECTOR('',#2194,2.200990050447E-1); -#2196=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.436518664575E0)); -#2197=LINE('',#2196,#2195); -#2198=DIRECTION('',(8.338427005713E-1,0.E0,-5.520021292568E-1)); -#2199=VECTOR('',#2198,1.530979093102E-1); -#2200=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,6.380178470356E0)); -#2201=LINE('',#2200,#2199); -#2202=DIRECTION('',(6.715587020023E-1,0.E0,-7.409513545199E-1)); -#2203=VECTOR('',#2202,1.900944326164E-1); -#2204=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,6.295668098432E0)); -#2205=LINE('',#2204,#2203); -#2206=DIRECTION('',(2.892058540675E-1,0.E0,-9.572669293217E-1)); -#2207=VECTOR('',#2206,1.471380663407E-1); -#2208=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,6.154817371098E0)); -#2209=LINE('',#2208,#2207); -#2210=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2211=VECTOR('',#2210,1.690207438480E-1); -#2212=CARTESIAN_POINT('',(2.E0,1.55E0,6.013966966146E0)); -#2213=LINE('',#2212,#2211); -#2214=DIRECTION('',(-2.892052474928E-1,0.E0,-9.572671125776E-1)); -#2215=VECTOR('',#2214,1.471383749459E-1); -#2216=CARTESIAN_POINT('',(2.E0,1.55E0,5.844946222298E0)); -#2217=LINE('',#2216,#2215); -#2218=DIRECTION('',(-6.715587020024E-1,0.E0,-7.409513545199E-1)); -#2219=VECTOR('',#2218,1.900944326164E-1); -#2220=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,5.704095494964E0)); -#2221=LINE('',#2220,#2219); -#2222=DIRECTION('',(-8.338427005713E-1,0.E0,-5.520021292568E-1)); -#2223=VECTOR('',#2222,1.530979093102E-1); -#2224=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,5.563244767630E0)); -#2225=LINE('',#2224,#2223); -#2226=DIRECTION('',(-9.666831602829E-1,0.E0,-2.559759121978E-1)); -#2227=VECTOR('',#2226,2.200989637837E-1); -#2228=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,5.478734395706E0)); -#2229=LINE('',#2228,#2227); -#2230=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2231=VECTOR('',#2230,1.276595592499E-1); -#2232=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.422394362678E0)); -#2233=LINE('',#2232,#2231); -#2234=DIRECTION('',(-9.666831691551E-1,0.E0,2.559758786924E-1)); -#2235=VECTOR('',#2234,2.200989925931E-1); -#2236=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.422394362678E0)); -#2237=LINE('',#2236,#2235); -#2238=DIRECTION('',(-7.497215250747E-1,0.E0,6.617534547244E-1)); -#2239=VECTOR('',#2238,1.702759691169E-1); -#2240=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,5.478734395706E0)); -#2241=LINE('',#2240,#2239); -#2242=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#2243=VECTOR('',#2242,7.060434119686E-2); -#2244=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,5.591415106526E0)); -#2245=LINE('',#2244,#2243); -#2246=DIRECTION('',(-6.026992915064E-1,0.E0,-7.979683978816E-1)); -#2247=VECTOR('',#2246,7.060434119686E-2); -#2248=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,5.647755139554E0)); -#2249=LINE('',#2248,#2247); -#2250=DIRECTION('',(-8.338426709139E-1,0.E0,-5.520021740566E-1)); -#2251=VECTOR('',#2250,1.530978968850E-1); -#2252=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,5.591415106526E0)); -#2253=LINE('',#2252,#2251); -#2254=DIRECTION('',(-9.493458507973E-1,0.E0,-3.142331229740E-1)); -#2255=VECTOR('',#2254,1.792947696812E-1); -#2256=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,5.506904734602E0)); -#2257=LINE('',#2256,#2255); -#2258=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2259=VECTOR('',#2258,1.276595592499E-1); -#2260=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,5.450564379192E0)); -#2261=LINE('',#2260,#2259); -#2262=DIRECTION('',(-9.666828244595E-1,0.E0,2.559771804186E-1)); -#2263=VECTOR('',#2262,2.200991327340E-1); -#2264=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.450564379192E0)); -#2265=LINE('',#2264,#2263); -#2266=DIRECTION('',(-8.338426709139E-1,0.E0,5.520021740566E-1)); -#2267=VECTOR('',#2266,1.530978968850E-1); -#2268=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.506904734602E0)); -#2269=LINE('',#2268,#2267); -#2270=DIRECTION('',(-6.715595135938E-1,0.E0,7.409506189360E-1)); -#2271=VECTOR('',#2270,1.900941862423E-1); -#2272=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,5.591415106526E0)); -#2273=LINE('',#2272,#2271); -#2274=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#2275=VECTOR('',#2274,1.471383738685E-1); -#2276=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,5.732265511478E0)); -#2277=LINE('',#2276,#2275); -#2278=DIRECTION('',(0.E0,0.E0,1.E0)); -#2279=VECTOR('',#2278,1.126803884382E-1); -#2280=CARTESIAN_POINT('',(0.E0,1.55E0,5.873116238812E0)); -#2281=LINE('',#2280,#2279); -#2282=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#2283=VECTOR('',#2282,1.471383738685E-1); -#2284=CARTESIAN_POINT('',(0.E0,1.55E0,5.985796627250E0)); -#2285=LINE('',#2284,#2283); -#2286=DIRECTION('',(6.715586697255E-1,0.E0,7.409513837739E-1)); -#2287=VECTOR('',#2286,1.900944251112E-1); -#2288=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,6.126647354584E0)); -#2289=LINE('',#2288,#2287); -#2290=DIRECTION('',(8.338431555277E-1,0.E0,5.520014420087E-1)); -#2291=VECTOR('',#2290,1.530978079074E-1); -#2292=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,6.267498081918E0)); -#2293=LINE('',#2292,#2291); -#2294=DIRECTION('',(9.666828244595E-1,0.E0,2.559771804186E-1)); -#2295=VECTOR('',#2294,2.200991327340E-1); -#2296=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,6.352008292651E0)); -#2297=LINE('',#2296,#2295); -#2298=DIRECTION('',(1.E0,0.E0,0.E0)); -#2299=VECTOR('',#2298,1.276595592499E-1); -#2300=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.408348648061E0)); -#2301=LINE('',#2300,#2299); -#2302=DIRECTION('',(9.493458507973E-1,0.E0,-3.142331229740E-1)); -#2303=VECTOR('',#2302,1.792947696812E-1); -#2304=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,6.408348648061E0)); -#2305=LINE('',#2304,#2303); -#2306=DIRECTION('',(8.338431555277E-1,0.E0,-5.520014420087E-1)); -#2307=VECTOR('',#2306,1.530978079074E-1); -#2308=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,6.352008292651E0)); -#2309=LINE('',#2308,#2307); -#2310=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#2311=VECTOR('',#2310,7.060459844737E-2); -#2312=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,6.267498081918E0)); -#2313=LINE('',#2312,#2311); -#2314=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#2315=VECTOR('',#2314,1.204479815731E-1); -#2316=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.985796627250E0)); -#2317=LINE('',#2316,#2315); -#2318=DIRECTION('',(-6.026981935262E-1,0.E0,7.979692271762E-1)); -#2319=VECTOR('',#2318,1.412089396441E-1); -#2320=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,6.098477338070E0)); -#2321=LINE('',#2320,#2319); -#2322=DIRECTION('',(-8.956781919070E-1,0.E0,4.447027957437E-1)); -#2323=VECTOR('',#2322,1.900378696353E-1); -#2324=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,6.211157726508E0)); -#2325=LINE('',#2324,#2323); -#2326=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2327=VECTOR('',#2326,1.276595592499E-1); -#2328=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.295668098432E0)); -#2329=LINE('',#2328,#2327); -#2330=DIRECTION('',(-8.956782229204E-1,0.E0,-4.447027332794E-1)); -#2331=VECTOR('',#2330,1.900378963286E-1); -#2332=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.295668098432E0)); -#2333=LINE('',#2332,#2331); -#2334=DIRECTION('',(-6.026981935262E-1,0.E0,-7.979692271762E-1)); -#2335=VECTOR('',#2334,1.412089396441E-1); -#2336=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,6.211157726508E0)); -#2337=LINE('',#2336,#2335); -#2338=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#2339=VECTOR('',#2338,1.204479815731E-1); -#2340=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,6.098477338070E0)); -#2341=LINE('',#2340,#2339); -#2342=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2343=VECTOR('',#2342,1.126803884382E-1); -#2344=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.985796627250E0)); -#2345=LINE('',#2344,#2343); -#2346=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#2347=VECTOR('',#2346,1.204476799809E-1); -#2348=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.873116238812E0)); -#2349=LINE('',#2348,#2347); -#2350=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#2351=VECTOR('',#2350,1.412091968947E-1); -#2352=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,5.760435850374E0)); -#2353=LINE('',#2352,#2351); -#2354=DIRECTION('',(8.956782229204E-1,0.E0,-4.447027332794E-1)); -#2355=VECTOR('',#2354,1.900378963286E-1); -#2356=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,5.647755139554E0)); -#2357=LINE('',#2356,#2355); -#2358=DIRECTION('',(1.E0,0.E0,0.E0)); -#2359=VECTOR('',#2358,1.276595592499E-1); -#2360=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.563244767630E0)); -#2361=LINE('',#2360,#2359); -#2362=DIRECTION('',(8.956781919070E-1,0.E0,4.447027957437E-1)); -#2363=VECTOR('',#2362,1.900378696353E-1); -#2364=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.563244767630E0)); -#2365=LINE('',#2364,#2363); -#2366=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#2367=VECTOR('',#2366,1.412091968947E-1); -#2368=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.647755139554E0)); -#2369=LINE('',#2368,#2367); -#2370=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#2371=VECTOR('',#2370,1.204476799809E-1); -#2372=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,5.760435850374E0)); -#2373=LINE('',#2372,#2371); -#2374=DIRECTION('',(0.E0,0.E0,1.E0)); -#2375=VECTOR('',#2374,1.126803884382E-1); -#2376=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.873116238812E0)); -#2377=LINE('',#2376,#2375); -#2378=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#2379=VECTOR('',#2378,1.204476799809E-1); -#2380=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.873116238812E0)); -#2381=LINE('',#2380,#2379); -#2382=DIRECTION('',(7.497215250746E-1,0.E0,-6.617534547244E-1)); -#2383=VECTOR('',#2382,1.702759691169E-1); -#2384=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,5.760435850374E0)); -#2385=LINE('',#2384,#2383); -#2386=DIRECTION('',(9.148659569677E-1,0.E0,-4.037577005848E-1)); -#2387=VECTOR('',#2386,1.395392160861E-1); -#2388=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,5.647755139554E0)); -#2389=LINE('',#2388,#2387); -#2390=DIRECTION('',(1.E0,0.E0,0.E0)); -#2391=VECTOR('',#2390,8.510637283325E-2); -#2392=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.591415106526E0)); -#2393=LINE('',#2392,#2391); -#2394=DIRECTION('',(9.148658176982E-1,0.E0,4.037580161524E-1)); -#2395=VECTOR('',#2394,1.395391070256E-1); -#2396=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,5.591415106526E0)); -#2397=LINE('',#2396,#2395); -#2398=DIRECTION('',(7.497215250746E-1,0.E0,6.617534547244E-1)); -#2399=VECTOR('',#2398,1.702759691169E-1); -#2400=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,5.647755139554E0)); -#2401=LINE('',#2400,#2399); -#2402=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#2403=VECTOR('',#2402,1.204476799809E-1); -#2404=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,5.760435850374E0)); -#2405=LINE('',#2404,#2403); -#2406=DIRECTION('',(0.E0,0.E0,1.E0)); -#2407=VECTOR('',#2406,1.126803884382E-1); -#2408=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.873116238812E0)); -#2409=LINE('',#2408,#2407); -#2410=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#2411=VECTOR('',#2410,1.204479815731E-1); -#2412=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.985796627250E0)); -#2413=LINE('',#2412,#2411); -#2414=DIRECTION('',(-7.497224643937E-1,0.E0,6.617523905385E-1)); -#2415=VECTOR('',#2414,1.702757557800E-1); -#2416=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,6.098477338070E0)); -#2417=LINE('',#2416,#2415); -#2418=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498490E-1)); -#2419=VECTOR('',#2418,1.395392371900E-1); -#2420=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,6.211157726508E0)); -#2421=LINE('',#2420,#2419); -#2422=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2423=VECTOR('',#2422,8.510637283325E-2); -#2424=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,6.267498081918E0)); -#2425=LINE('',#2424,#2423); -#2426=DIRECTION('',(-9.148651035675E-1,0.E0,-4.037596342805E-1)); -#2427=VECTOR('',#2426,1.395393462505E-1); -#2428=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.267498081918E0)); -#2429=LINE('',#2428,#2427); -#2430=DIRECTION('',(-7.497224643937E-1,0.E0,-6.617523905385E-1)); -#2431=VECTOR('',#2430,1.702757557800E-1); -#2432=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,6.211157726508E0)); -#2433=LINE('',#2432,#2431); -#2434=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#2435=VECTOR('',#2434,1.204479815731E-1); -#2436=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,6.098477338070E0)); -#2437=LINE('',#2436,#2435); -#2438=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2439=VECTOR('',#2438,1.126803884382E-1); -#2440=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.985796627250E0)); -#2441=LINE('',#2440,#2439); -#2442=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498490E-1)); -#2443=VECTOR('',#2442,1.395392371900E-1); -#2444=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.267419172256E0)); -#2445=LINE('',#2444,#2443); -#2446=DIRECTION('',(-9.765079811284E-1,0.E0,-2.154812353607E-1)); -#2447=VECTOR('',#2446,1.307307175356E-1); -#2448=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,4.211078816846E0)); -#2449=LINE('',#2448,#2447); -#2450=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2451=VECTOR('',#2450,1.702127456665E-1); -#2452=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.182908800332E0)); -#2453=LINE('',#2452,#2451); -#2454=DIRECTION('',(-9.865801276635E-1,0.E0,1.632778359099E-1)); -#2455=VECTOR('',#2454,1.725281104884E-1); -#2456=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.182908800332E0)); -#2457=LINE('',#2456,#2455); -#2458=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498490E-1)); -#2459=VECTOR('',#2458,1.395392371900E-1); -#2460=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.211078816846E0)); -#2461=LINE('',#2460,#2459); -#2462=DIRECTION('',(-5.171559642137E-1,0.E0,8.558911780584E-1)); -#2463=VECTOR('',#2462,1.645661632514E-1); -#2464=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.267419172256E0)); -#2465=LINE('',#2464,#2463); -#2466=DIRECTION('',(-7.497215250747E-1,0.E0,-6.617534547244E-1)); -#2467=VECTOR('',#2466,1.702759691169E-1); -#2468=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,4.408269899590E0)); -#2469=LINE('',#2468,#2467); -#2470=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#2471=VECTOR('',#2470,1.395391070256E-1); -#2472=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,4.295589188770E0)); -#2473=LINE('',#2472,#2471); -#2474=DIRECTION('',(-9.865798174491E-1,0.E0,-1.632797103197E-1)); -#2475=VECTOR('',#2474,1.725281043217E-1); -#2476=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.239249155742E0)); -#2477=LINE('',#2476,#2475); -#2478=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2479=VECTOR('',#2478,8.510649204254E-2); -#2480=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.211078816846E0)); -#2481=LINE('',#2480,#2479); -#2482=DIRECTION('',(-9.865798174491E-1,0.E0,1.632797103197E-1)); -#2483=VECTOR('',#2482,1.725281043217E-1); -#2484=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.211078816846E0)); -#2485=LINE('',#2484,#2483); -#2486=DIRECTION('',(-8.338429132208E-1,0.E0,5.520018080328E-1)); -#2487=VECTOR('',#2486,2.041304698616E-1); -#2488=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,4.239249155742E0)); -#2489=LINE('',#2488,#2487); -#2490=DIRECTION('',(-6.026981935263E-1,0.E0,7.979692271762E-1)); -#2491=VECTOR('',#2490,1.412089396441E-1); -#2492=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,4.351929544180E0)); -#2493=LINE('',#2492,#2491); -#2494=DIRECTION('',(-2.109410206761E-1,0.E0,9.774987906878E-1)); -#2495=VECTOR('',#2494,2.017302574921E-1); -#2496=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.464609932618E0)); -#2497=LINE('',#2496,#2495); -#2498=DIRECTION('',(0.E0,0.E0,1.E0)); -#2499=VECTOR('',#2498,5.634003302834E-2); -#2500=CARTESIAN_POINT('',(0.E0,1.55E0,4.661801015362E0)); -#2501=LINE('',#2500,#2499); -#2502=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#2503=VECTOR('',#2502,2.017302574921E-1); -#2504=CARTESIAN_POINT('',(0.E0,1.55E0,4.718141048390E0)); -#2505=LINE('',#2504,#2503); -#2506=DIRECTION('',(6.026981935262E-1,0.E0,7.979692271762E-1)); -#2507=VECTOR('',#2506,1.412089396441E-1); -#2508=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.915332131134E0)); -#2509=LINE('',#2508,#2507); -#2510=DIRECTION('',(8.338429132208E-1,0.E0,5.520018080328E-1)); -#2511=VECTOR('',#2510,2.041304698616E-1); -#2512=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,5.028012519572E0)); -#2513=LINE('',#2512,#2511); -#2514=DIRECTION('',(9.865798174491E-1,0.E0,1.632797103197E-1)); -#2515=VECTOR('',#2514,1.725281043217E-1); -#2516=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.140692908010E0)); -#2517=LINE('',#2516,#2515); -#2518=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2519=VECTOR('',#2518,1.408507273338E-1); -#2520=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.168863246906E0)); -#2521=LINE('',#2520,#2519); -#2522=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498490E-1)); -#2523=VECTOR('',#2522,1.395392371900E-1); -#2524=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.028012519572E0)); -#2525=LINE('',#2524,#2523); -#2526=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#2527=VECTOR('',#2526,1.199378908417E-1); -#2528=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.971672164162E0)); -#2529=LINE('',#2528,#2527); -#2530=DIRECTION('',(-2.892058308668E-1,0.E0,-9.572669363311E-1)); -#2531=VECTOR('',#2530,1.471380652634E-1); -#2532=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.887161792238E0)); -#2533=LINE('',#2532,#2531); -#2534=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2535=VECTOR('',#2534,1.126807108197E-1); -#2536=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.746311387286E0)); -#2537=LINE('',#2536,#2535); -#2538=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#2539=VECTOR('',#2538,1.471380652634E-1); -#2540=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.633630676466E0)); -#2541=LINE('',#2540,#2539); -#2542=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#2543=VECTOR('',#2542,1.199378908417E-1); -#2544=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.492780271514E0)); -#2545=LINE('',#2544,#2543); -#2546=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#2547=VECTOR('',#2546,1.395392371900E-1); -#2548=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.408269899590E0)); -#2549=LINE('',#2548,#2547); -#2550=DIRECTION('',(1.E0,0.E0,0.E0)); -#2551=VECTOR('',#2550,8.510649204254E-2); -#2552=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.351929544180E0)); -#2553=LINE('',#2552,#2551); -#2554=DIRECTION('',(9.493458507973E-1,0.E0,3.142331229740E-1)); -#2555=VECTOR('',#2554,1.792947696812E-1); -#2556=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.351929544180E0)); -#2557=LINE('',#2556,#2555); -#2558=DIRECTION('',(8.338436401413E-1,0.E0,5.520007099595E-1)); -#2559=VECTOR('',#2558,1.020651459533E-1); -#2560=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.408269899590E0)); -#2561=LINE('',#2560,#2559); -#2562=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#2563=VECTOR('',#2562,1.892382269727E-1); -#2564=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,4.464609932618E0)); -#2565=LINE('',#2564,#2563); -#2566=DIRECTION('',(0.E0,0.E0,1.E0)); -#2567=VECTOR('',#2566,1.126807108197E-1); -#2568=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.633630676466E0)); -#2569=LINE('',#2568,#2567); -#2570=DIRECTION('',(1.E0,0.E0,0.E0)); -#2571=VECTOR('',#2570,1.702127456665E-1); -#2572=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.746311387286E0)); -#2573=LINE('',#2572,#2571); -#2574=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2575=VECTOR('',#2574,1.126807108197E-1); -#2576=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.746311387286E0)); -#2577=LINE('',#2576,#2575); -#2578=DIRECTION('',(2.441444645688E-1,0.E0,-9.697388722849E-1)); -#2579=VECTOR('',#2578,1.742951104453E-1); -#2580=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.633630676466E0)); -#2581=LINE('',#2580,#2579); -#2582=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#2583=VECTOR('',#2582,1.199378908417E-1); -#2584=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,4.464609932618E0)); -#2585=LINE('',#2584,#2583); -#2586=DIRECTION('',(9.493464200095E-1,0.E0,-3.142314032923E-1)); -#2587=VECTOR('',#2586,1.792947249640E-1); -#2588=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.380099560694E0)); -#2589=LINE('',#2588,#2587); -#2590=DIRECTION('',(1.E0,0.E0,0.E0)); -#2591=VECTOR('',#2590,1.702127456665E-1); -#2592=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.323759527666E0)); -#2593=LINE('',#2592,#2591); -#2594=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#2595=VECTOR('',#2594,8.964733418926E-2); -#2596=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.323759527666E0)); -#2597=LINE('',#2596,#2595); -#2598=DIRECTION('',(8.338422752723E-1,0.E0,5.520027717038E-1)); -#2599=VECTOR('',#2598,1.020653487589E-1); -#2600=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,4.351929544180E0)); -#2601=LINE('',#2600,#2599); -#2602=DIRECTION('',(6.026992915064E-1,0.E0,7.979683978816E-1)); -#2603=VECTOR('',#2602,7.060434119686E-2); -#2604=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.408269899590E0)); -#2605=LINE('',#2604,#2603); -#2606=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#2607=VECTOR('',#2606,1.471383738685E-1); -#2608=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.464609932618E0)); -#2609=LINE('',#2608,#2607); -#2610=DIRECTION('',(0.E0,0.E0,1.E0)); -#2611=VECTOR('',#2610,1.690207438480E-1); -#2612=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.605460659952E0)); -#2613=LINE('',#2612,#2611); -#2614=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#2615=VECTOR('',#2614,1.471383738685E-1); -#2616=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.774481403800E0)); -#2617=LINE('',#2616,#2615); -#2618=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#2619=VECTOR('',#2618,7.060434119686E-2); -#2620=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.915332131134E0)); -#2621=LINE('',#2620,#2619); -#2622=DIRECTION('',(-8.338422752723E-1,0.E0,5.520027717038E-1)); -#2623=VECTOR('',#2622,1.020653487589E-1); -#2624=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.971672164162E0)); -#2625=LINE('',#2624,#2623); -#2626=DIRECTION('',(-9.493463871840E-1,0.E0,3.142315024639E-1)); -#2627=VECTOR('',#2626,8.964733418926E-2); -#2628=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,5.028012519572E0)); -#2629=LINE('',#2628,#2627); -#2630=DIRECTION('',(0.E0,0.E0,1.E0)); -#2631=VECTOR('',#2630,1.408507273338E-1); -#2632=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.056182536086E0)); -#2633=LINE('',#2632,#2631); -#2634=DIRECTION('',(9.765079811284E-1,0.E0,-2.154812353607E-1)); -#2635=VECTOR('',#2634,1.307307175356E-1); -#2636=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.197033263420E0)); -#2637=LINE('',#2636,#2635); -#2638=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#2639=VECTOR('',#2638,1.395392371900E-1); -#2640=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.168863246906E0)); -#2641=LINE('',#2640,#2639); -#2642=DIRECTION('',(7.095871007418E-1,0.E0,-7.046177307313E-1)); -#2643=VECTOR('',#2642,1.199379014154E-1); -#2644=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.112522891496E0)); -#2645=LINE('',#2644,#2643); -#2646=DIRECTION('',(6.026982439217E-1,0.E0,-7.979691891130E-1)); -#2647=VECTOR('',#2646,1.412089463798E-1); -#2648=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,5.028012519572E0)); -#2649=LINE('',#2648,#2647); -#2650=DIRECTION('',(3.532910151020E-1,0.E0,-9.355134732585E-1)); -#2651=VECTOR('',#2650,1.204479828892E-1); -#2652=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.915332131134E0)); -#2653=LINE('',#2652,#2651); -#2654=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2655=VECTOR('',#2654,2.253607768763E-1); -#2656=CARTESIAN_POINT('',(2.E0,1.55E0,4.802651420314E0)); -#2657=LINE('',#2656,#2655); -#2658=DIRECTION('',(-3.532910151020E-1,0.E0,-9.355134732585E-1)); -#2659=VECTOR('',#2658,1.204479828892E-1); -#2660=CARTESIAN_POINT('',(2.E0,1.55E0,4.577290643438E0)); -#2661=LINE('',#2660,#2659); -#2662=DIRECTION('',(-6.026982439217E-1,0.E0,-7.979691891130E-1)); -#2663=VECTOR('',#2662,1.412089463798E-1); -#2664=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.464609932618E0)); -#2665=LINE('',#2664,#2663); -#2666=DIRECTION('',(-7.095871007418E-1,0.E0,-7.046177307313E-1)); -#2667=VECTOR('',#2666,1.199379014154E-1); -#2668=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,4.351929544180E0)); -#2669=LINE('',#2668,#2667); -#2670=DIRECTION('',(1.E0,0.E0,0.E0)); -#2671=VECTOR('',#2670,2.127659618855E-1); -#2672=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.957547701074E0)); -#2673=LINE('',#2672,#2671); -#2674=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2675=VECTOR('',#2674,1.014124140706E0); -#2676=CARTESIAN_POINT('',(2.E0,1.55E0,3.957547701074E0)); -#2677=LINE('',#2676,#2675); -#2678=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2679=VECTOR('',#2678,2.127659618855E-1); -#2680=CARTESIAN_POINT('',(2.E0,1.55E0,2.943423560368E0)); -#2681=LINE('',#2680,#2679); -#2682=DIRECTION('',(0.E0,0.E0,1.E0)); -#2683=VECTOR('',#2682,7.887633638302E-1); -#2684=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,2.943423560368E0)); -#2685=LINE('',#2684,#2683); -#2686=DIRECTION('',(-7.991283277492E-1,0.E0,-6.011604742403E-1)); -#2687=VECTOR('',#2686,1.171489181480E0); -#2688=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.732186924198E0)); -#2689=LINE('',#2688,#2687); -#2690=DIRECTION('',(-9.148641108930E-1,0.E0,-4.037618835403E-1)); -#2691=VECTOR('',#2690,1.395393673551E-1); -#2692=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,3.027933932292E0)); -#2693=LINE('',#2692,#2691); -#2694=DIRECTION('',(-9.865804194541E-1,0.E0,-1.632760728023E-1)); -#2695=VECTOR('',#2694,1.725279990461E-1); -#2696=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,2.971593254501E0)); -#2697=LINE('',#2696,#2695); -#2698=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2699=VECTOR('',#2698,8.510649204254E-2); -#2700=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,2.943423560368E0)); -#2701=LINE('',#2700,#2699); -#2702=DIRECTION('',(-9.865804194541E-1,0.E0,1.632760728023E-1)); -#2703=VECTOR('',#2702,1.725279990461E-1); -#2704=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,2.943423560368E0)); -#2705=LINE('',#2704,#2703); -#2706=DIRECTION('',(-8.338421863001E-1,0.E0,5.520029061031E-1)); -#2707=VECTOR('',#2706,2.041306478169E-1); -#2708=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,2.971593254501E0)); -#2709=LINE('',#2708,#2707); -#2710=DIRECTION('',(-6.026970955489E-1,0.E0,7.979700564663E-1)); -#2711=VECTOR('',#2710,1.412091968947E-1); -#2712=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.084273965320E0)); -#2713=LINE('',#2712,#2711); -#2714=DIRECTION('',(-2.441444645688E-1,0.E0,9.697388722849E-1)); -#2715=VECTOR('',#2714,1.742951104453E-1); -#2716=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.196954676140E0)); -#2717=LINE('',#2716,#2715); -#2718=DIRECTION('',(0.E0,0.E0,1.E0)); -#2719=VECTOR('',#2718,1.126800660567E-1); -#2720=CARTESIAN_POINT('',(0.E0,1.55E0,3.365975419988E0)); -#2721=LINE('',#2720,#2719); -#2722=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#2723=VECTOR('',#2722,2.017302574921E-1); -#2724=CARTESIAN_POINT('',(0.E0,1.55E0,3.478655486044E0)); -#2725=LINE('',#2724,#2723); -#2726=DIRECTION('',(6.026981935263E-1,0.E0,7.979692271762E-1)); -#2727=VECTOR('',#2726,1.412089396441E-1); -#2728=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.675846568788E0)); -#2729=LINE('',#2728,#2727); -#2730=DIRECTION('',(8.338421863001E-1,0.E0,5.520029061031E-1)); -#2731=VECTOR('',#2730,2.041306478169E-1); -#2732=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.788526957226E0)); -#2733=LINE('',#2732,#2731); -#2734=DIRECTION('',(9.865801184532E-1,0.E0,1.632778915618E-1)); -#2735=VECTOR('',#2734,1.725280516836E-1); -#2736=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,3.901207668046E0)); -#2737=LINE('',#2736,#2735); -#2738=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2739=VECTOR('',#2738,1.408507273338E-1); -#2740=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.929377684560E0)); -#2741=LINE('',#2740,#2739); -#2742=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#2743=VECTOR('',#2742,1.395391070256E-1); -#2744=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.788526957226E0)); -#2745=LINE('',#2744,#2743); -#2746=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#2747=VECTOR('',#2746,1.199378908417E-1); -#2748=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.732186924198E0)); -#2749=LINE('',#2748,#2747); -#2750=DIRECTION('',(-2.892052242921E-1,0.E0,-9.572671195869E-1)); -#2751=VECTOR('',#2750,1.471383738685E-1); -#2752=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.647676552274E0)); -#2753=LINE('',#2752,#2751); -#2754=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2755=VECTOR('',#2754,1.126807108197E-1); -#2756=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.506825824940E0)); -#2757=LINE('',#2756,#2755); -#2758=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#2759=VECTOR('',#2758,1.471380652634E-1); -#2760=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.394145114120E0)); -#2761=LINE('',#2760,#2759); -#2762=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#2763=VECTOR('',#2762,1.199378908417E-1); -#2764=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.253294709168E0)); -#2765=LINE('',#2764,#2763); -#2766=DIRECTION('',(9.148658176982E-1,0.E0,-4.037580161524E-1)); -#2767=VECTOR('',#2766,1.395391070256E-1); -#2768=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.168784337244E0)); -#2769=LINE('',#2768,#2767); -#2770=DIRECTION('',(1.E0,0.E0,0.E0)); -#2771=VECTOR('',#2770,8.510649204254E-2); -#2772=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.112444304216E0)); -#2773=LINE('',#2772,#2771); -#2774=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#2775=VECTOR('',#2774,1.792946683785E-1); -#2776=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,3.112444304216E0)); -#2777=LINE('',#2776,#2775); -#2778=DIRECTION('',(8.032893743823E-1,0.E0,5.955889362677E-1)); -#2779=VECTOR('',#2778,1.324341867015E0); -#2780=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,3.168784337244E0)); -#2781=LINE('',#2780,#2779); -#2782=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2783=VECTOR('',#2782,1.690207438480E-1); -#2784=CARTESIAN_POINT('',(2.E0,1.55E0,1.760278353432E0)); -#2785=LINE('',#2784,#2783); -#2786=DIRECTION('',(-9.054015226808E-1,0.E0,4.245563363410E-1)); -#2787=VECTOR('',#2786,1.127981970015E0); -#2788=CARTESIAN_POINT('',(2.E0,1.55E0,1.591257609584E0)); -#2789=LINE('',#2788,#2787); -#2790=DIRECTION('',(-8.982376862285E-1,0.E0,-4.395100215454E-1)); -#2791=VECTOR('',#2790,1.089604034430E0); -#2792=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.070149502232E0)); -#2793=LINE('',#2792,#2791); -#2794=DIRECTION('',(0.E0,0.E0,1.E0)); -#2795=VECTOR('',#2794,1.690207438480E-1); -#2796=CARTESIAN_POINT('',(0.E0,1.55E0,1.591257609584E0)); -#2797=LINE('',#2796,#2795); -#2798=DIRECTION('',(8.987745446082E-1,0.E0,4.384111289239E-1)); -#2799=VECTOR('',#2798,8.995700489911E-1); -#2800=CARTESIAN_POINT('',(0.E0,1.55E0,1.760278353432E0)); -#2801=LINE('',#2800,#2799); -#2802=DIRECTION('',(-8.987745446082E-1,0.E0,4.384111289239E-1)); -#2803=VECTOR('',#2802,8.995700489911E-1); -#2804=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,2.154659874156E0)); -#2805=LINE('',#2804,#2803); -#2806=DIRECTION('',(0.E0,0.E0,1.E0)); -#2807=VECTOR('',#2806,1.690207438480E-1); -#2808=CARTESIAN_POINT('',(0.E0,1.55E0,2.549041394881E0)); -#2809=LINE('',#2808,#2807); -#2810=DIRECTION('',(8.982376862285E-1,0.E0,-4.395100215454E-1)); -#2811=VECTOR('',#2810,1.089604034430E0); -#2812=CARTESIAN_POINT('',(0.E0,1.55E0,2.718062138729E0)); -#2813=LINE('',#2812,#2811); -#2814=DIRECTION('',(9.054015226808E-1,0.E0,4.245563363410E-1)); -#2815=VECTOR('',#2814,1.127981970015E0); -#2816=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.239170246080E0)); -#2817=LINE('',#2816,#2815); -#2818=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2819=VECTOR('',#2818,1.690207438480E-1); -#2820=CARTESIAN_POINT('',(2.E0,1.55E0,2.718062138729E0)); -#2821=LINE('',#2820,#2819); -#2822=DIRECTION('',(-8.987745446082E-1,0.E0,-4.384111289239E-1)); -#2823=VECTOR('',#2822,8.995700489911E-1); -#2824=CARTESIAN_POINT('',(2.E0,1.55E0,2.549041394881E0)); -#2825=LINE('',#2824,#2823); -#2826=DIRECTION('',(8.987745446082E-1,0.E0,-4.384111289239E-1)); -#2827=VECTOR('',#2826,8.995700489911E-1); -#2828=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,2.154659874156E0)); -#2829=LINE('',#2828,#2827); -#2830=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2831=VECTOR('',#2830,4.680851101875E-1); -#2832=CARTESIAN_POINT('',(4.E0,1.55E0,1.03375E1)); -#2833=LINE('',#2832,#2831); -#2834=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2835=VECTOR('',#2834,4.875000178814E-1); -#2836=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.03375E1)); -#2837=LINE('',#2836,#2835); -#2838=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2839=VECTOR('',#2838,1.276595592499E-1); -#2840=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,9.849999982119E0)); -#2841=LINE('',#2840,#2839); -#2842=DIRECTION('',(0.E0,0.E0,1.E0)); -#2843=VECTOR('',#2842,4.875000178814E-1); -#2844=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,9.849999982119E0)); -#2845=LINE('',#2844,#2843); -#2846=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2847=VECTOR('',#2846,2.765957713127E-1); -#2848=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.03375E1)); -#2849=LINE('',#2848,#2847); -#2850=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2851=VECTOR('',#2850,5.625E-1); -#2852=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.03375E1)); -#2853=LINE('',#2852,#2851); -#2854=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2855=VECTOR('',#2854,1.276595592499E-1); -#2856=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.775E0)); -#2857=LINE('',#2856,#2855); -#2858=DIRECTION('',(0.E0,0.E0,1.E0)); -#2859=VECTOR('',#2858,6.75E-1); -#2860=CARTESIAN_POINT('',(3.E0,1.55E0,9.775E0)); -#2861=LINE('',#2860,#2859); -#2862=DIRECTION('',(1.E0,0.E0,0.E0)); -#2863=VECTOR('',#2862,1.E0); -#2864=CARTESIAN_POINT('',(3.E0,1.55E0,1.045E1)); -#2865=LINE('',#2864,#2863); -#2866=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2867=VECTOR('',#2866,1.125E-1); -#2868=CARTESIAN_POINT('',(4.E0,1.55E0,1.045E1)); -#2869=LINE('',#2868,#2867); -#2870=DIRECTION('',(0.E0,0.E0,1.E0)); -#2871=VECTOR('',#2870,1.125E-1); -#2872=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.893750035763E0)); -#2873=LINE('',#2872,#2871); -#2874=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906686E-1)); -#2875=VECTOR('',#2874,6.652669076968E-2); -#2876=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.006250035763E0)); -#2877=LINE('',#2876,#2875); -#2878=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#2879=VECTOR('',#2878,7.053252754859E-2); -#2880=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.024999964237E0)); -#2881=LINE('',#2880,#2879); -#2882=DIRECTION('',(2.729182037179E-1,0.E0,9.620372415242E-1)); -#2883=VECTOR('',#2882,7.795959711909E-2); -#2884=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.081249964237E0)); -#2885=LINE('',#2884,#2883); -#2886=DIRECTION('',(0.E0,0.E0,1.E0)); -#2887=VECTOR('',#2886,1.6875E-1); -#2888=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.15625E0)); -#2889=LINE('',#2888,#2887); -#2890=DIRECTION('',(-2.729182037179E-1,0.E0,9.620372415242E-1)); -#2891=VECTOR('',#2890,7.795959711909E-2); -#2892=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.325E0)); -#2893=LINE('',#2892,#2891); -#2894=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#2895=VECTOR('',#2894,7.053252754859E-2); -#2896=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.400000035763E0)); -#2897=LINE('',#2896,#2895); -#2898=DIRECTION('',(-8.622113312198E-1,0.E0,5.065487343940E-1)); -#2899=VECTOR('',#2898,7.403031868607E-2); -#2900=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.456250035763E0)); -#2901=LINE('',#2900,#2899); -#2902=DIRECTION('',(-9.765802913621E-1,0.E0,2.151532814604E-1)); -#2903=VECTOR('',#2902,8.714733810013E-2); -#2904=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.49375E0)); -#2905=LINE('',#2904,#2903); -#2906=DIRECTION('',(-1.E0,0.E0,0.E0)); -#2907=VECTOR('',#2906,3.191489279270E-1); -#2908=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.512500035763E0)); -#2909=LINE('',#2908,#2907); -#2910=DIRECTION('',(-9.765802913621E-1,0.E0,-2.151532814604E-1)); -#2911=VECTOR('',#2910,8.714733810013E-2); -#2912=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.512500035763E0)); -#2913=LINE('',#2912,#2911); -#2914=DIRECTION('',(-8.622115378113E-1,0.E0,-5.065483827484E-1)); -#2915=VECTOR('',#2914,7.403037007787E-2); -#2916=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.49375E0)); -#2917=LINE('',#2916,#2915); -#2918=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#2919=VECTOR('',#2918,7.053251855852E-2); -#2920=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.456250035763E0)); -#2921=LINE('',#2920,#2919); -#2922=DIRECTION('',(-2.729182037179E-1,0.E0,-9.620372415242E-1)); -#2923=VECTOR('',#2922,7.795959711909E-2); -#2924=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.400000035763E0)); -#2925=LINE('',#2924,#2923); -#2926=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2927=VECTOR('',#2926,1.6875E-1); -#2928=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.325E0)); -#2929=LINE('',#2928,#2927); -#2930=DIRECTION('',(2.729182037179E-1,0.E0,-9.620372415242E-1)); -#2931=VECTOR('',#2930,7.795959711909E-2); -#2932=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.15625E0)); -#2933=LINE('',#2932,#2931); -#2934=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#2935=VECTOR('',#2934,7.053251855852E-2); -#2936=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.081249964237E0)); -#2937=LINE('',#2936,#2935); -#2938=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#2939=VECTOR('',#2938,6.652674795802E-2); -#2940=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.024999964237E0)); -#2941=LINE('',#2940,#2939); -#2942=DIRECTION('',(0.E0,0.E0,-1.E0)); -#2943=VECTOR('',#2942,1.125E-1); -#2944=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.006250035763E0)); -#2945=LINE('',#2944,#2943); -#2946=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#2947=VECTOR('',#2946,1.080227196632E-1); -#2948=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.893750035763E0)); -#2949=LINE('',#2948,#2947); -#2950=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#2951=VECTOR('',#2950,1.134376483415E-1); -#2952=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.912499964237E0)); -#2953=LINE('',#2952,#2951); -#2954=DIRECTION('',(-4.934791955020E-1,0.E0,8.697576004880E-1)); -#2955=VECTOR('',#2954,8.623096334048E-2); -#2956=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.9875E0)); -#2957=LINE('',#2956,#2955); -#2958=DIRECTION('',(-2.213222112791E-1,0.E0,9.752007376918E-1)); -#2959=VECTOR('',#2958,9.613401694006E-2); -#2960=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.062500035763E0)); -#2961=LINE('',#2960,#2959); -#2962=DIRECTION('',(0.E0,0.E0,1.E0)); -#2963=VECTOR('',#2962,1.6875E-1); -#2964=CARTESIAN_POINT('',(3.E0,1.55E0,9.15625E0)); -#2965=LINE('',#2964,#2963); -#2966=DIRECTION('',(2.213222112791E-1,0.E0,9.752007376918E-1)); -#2967=VECTOR('',#2966,9.613401694006E-2); -#2968=CARTESIAN_POINT('',(3.E0,1.55E0,9.325E0)); -#2969=LINE('',#2968,#2967); -#2970=DIRECTION('',(4.934791955020E-1,0.E0,8.697576004880E-1)); -#2971=VECTOR('',#2970,8.623096334048E-2); -#2972=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.418749964237E0)); -#2973=LINE('',#2972,#2971); -#2974=DIRECTION('',(7.502482701883E-1,0.E0,6.611562092875E-1)); -#2975=VECTOR('',#2974,1.134376128743E-1); -#2976=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,9.49375E0)); -#2977=LINE('',#2976,#2975); -#2978=DIRECTION('',(9.151039825100E-1,0.E0,4.032179326300E-1)); -#2979=VECTOR('',#2978,9.300186040041E-2); -#2980=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.568749982119E0)); -#2981=LINE('',#2980,#2979); -#2982=DIRECTION('',(9.848207562999E-1,0.E0,1.735744162049E-1)); -#2983=VECTOR('',#2982,1.080227289745E-1); -#2984=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,9.60625E0)); -#2985=LINE('',#2984,#2983); -#2986=DIRECTION('',(1.E0,0.E0,0.E0)); -#2987=VECTOR('',#2986,3.191489279270E-1); -#2988=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.624999982119E0)); -#2989=LINE('',#2988,#2987); -#2990=DIRECTION('',(9.848207396759E-1,0.E0,-1.735745105259E-1)); -#2991=VECTOR('',#2990,1.080226702746E-1); -#2992=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.624999982119E0)); -#2993=LINE('',#2992,#2991); -#2994=DIRECTION('',(9.151040085600E-1,0.E0,-4.032178735094E-1)); -#2995=VECTOR('',#2994,9.300187403652E-2); -#2996=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,9.60625E0)); -#2997=LINE('',#2996,#2995); -#2998=DIRECTION('',(7.502482988989E-1,0.E0,-6.611561767082E-1)); -#2999=VECTOR('',#2998,1.134376184641E-1); -#3000=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.568749982119E0)); -#3001=LINE('',#3000,#2999); -#3002=DIRECTION('',(4.934792445233E-1,0.E0,-8.697575726745E-1)); -#3003=VECTOR('',#3002,8.623096609801E-2); -#3004=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,9.49375E0)); -#3005=LINE('',#3004,#3003); -#3006=DIRECTION('',(2.213222297055E-1,0.E0,-9.752007335099E-1)); -#3007=VECTOR('',#3006,9.613401735230E-2); -#3008=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.418749964237E0)); -#3009=LINE('',#3008,#3007); -#3010=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3011=VECTOR('',#3010,1.6875E-1); -#3012=CARTESIAN_POINT('',(4.E0,1.55E0,9.325E0)); -#3013=LINE('',#3012,#3011); -#3014=DIRECTION('',(-2.213222297055E-1,0.E0,-9.752007335099E-1)); -#3015=VECTOR('',#3014,9.613401735230E-2); -#3016=CARTESIAN_POINT('',(4.E0,1.55E0,9.15625E0)); -#3017=LINE('',#3016,#3015); -#3018=DIRECTION('',(-4.934792445233E-1,0.E0,-8.697575726745E-1)); -#3019=VECTOR('',#3018,8.623096609801E-2); -#3020=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.062500035763E0)); -#3021=LINE('',#3020,#3019); -#3022=DIRECTION('',(-7.502480643278E-1,0.E0,-6.611564428881E-1)); -#3023=VECTOR('',#3022,1.134376539313E-1); -#3024=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.9875E0)); -#3025=LINE('',#3024,#3023); -#3026=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#3027=VECTOR('',#3026,1.080226756383E-1); -#3028=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.912499964237E0)); -#3029=LINE('',#3028,#3027); -#3030=DIRECTION('',(0.E0,0.E0,1.E0)); -#3031=VECTOR('',#3030,1.125E-1); -#3032=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.012500071526E0)); -#3033=LINE('',#3032,#3031); -#3034=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906686E-1)); -#3035=VECTOR('',#3034,6.652669076968E-2); -#3036=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.125000071526E0)); -#3037=LINE('',#3036,#3035); -#3038=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#3039=VECTOR('',#3038,7.053252754859E-2); -#3040=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.14375E0)); -#3041=LINE('',#3040,#3039); -#3042=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#3043=VECTOR('',#3042,7.795949390370E-2); -#3044=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.2E0)); -#3045=LINE('',#3044,#3043); -#3046=DIRECTION('',(0.E0,0.E0,1.E0)); -#3047=VECTOR('',#3046,1.6875E-1); -#3048=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.274999928474E0)); -#3049=LINE('',#3048,#3047); -#3050=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#3051=VECTOR('',#3050,7.795970033450E-2); -#3052=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.443749928474E0)); -#3053=LINE('',#3052,#3051); -#3054=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#3055=VECTOR('',#3054,7.053252754859E-2); -#3056=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.518750071526E0)); -#3057=LINE('',#3056,#3055); -#3058=DIRECTION('',(-8.622119641820E-1,0.E0,5.065476570090E-1)); -#3059=VECTOR('',#3058,7.403026433934E-2); -#3060=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.575000071526E0)); -#3061=LINE('',#3060,#3059); -#3062=DIRECTION('',(-9.765800326865E-1,0.E0,2.151544555851E-1)); -#3063=VECTOR('',#3062,8.714736118363E-2); -#3064=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.612499928474E0)); -#3065=LINE('',#3064,#3063); -#3066=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3067=VECTOR('',#3066,3.191489279270E-1); -#3068=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.631250071526E0)); -#3069=LINE('',#3068,#3067); -#3070=DIRECTION('',(-9.765800326865E-1,0.E0,-2.151544555851E-1)); -#3071=VECTOR('',#3070,8.714736118363E-2); -#3072=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.631250071526E0)); -#3073=LINE('',#3072,#3071); -#3074=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#3075=VECTOR('',#3074,7.403031573119E-2); -#3076=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.612499928474E0)); -#3077=LINE('',#3076,#3075); -#3078=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#3079=VECTOR('',#3078,7.053251855852E-2); -#3080=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.575000071526E0)); -#3081=LINE('',#3080,#3079); -#3082=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#3083=VECTOR('',#3082,7.795970033450E-2); -#3084=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.518750071526E0)); -#3085=LINE('',#3084,#3083); -#3086=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3087=VECTOR('',#3086,1.6875E-1); -#3088=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.443749928474E0)); -#3089=LINE('',#3088,#3087); -#3090=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#3091=VECTOR('',#3090,7.795949390370E-2); -#3092=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.274999928474E0)); -#3093=LINE('',#3092,#3091); -#3094=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#3095=VECTOR('',#3094,7.053251855852E-2); -#3096=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.2E0)); -#3097=LINE('',#3096,#3095); -#3098=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#3099=VECTOR('',#3098,6.652674795802E-2); -#3100=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.14375E0)); -#3101=LINE('',#3100,#3099); -#3102=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3103=VECTOR('',#3102,1.125E-1); -#3104=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.125000071526E0)); -#3105=LINE('',#3104,#3103); -#3106=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#3107=VECTOR('',#3106,1.080227196632E-1); -#3108=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.012500071526E0)); -#3109=LINE('',#3108,#3107); -#3110=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#3111=VECTOR('',#3110,1.134375774071E-1); -#3112=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.03125E0)); -#3113=LINE('',#3112,#3111); -#3114=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#3115=VECTOR('',#3114,8.623105665536E-2); -#3116=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.106249928474E0)); -#3117=LINE('',#3116,#3115); -#3118=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#3119=VECTOR('',#3118,9.613391231237E-2); -#3120=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.181250071526E0)); -#3121=LINE('',#3120,#3119); -#3122=DIRECTION('',(0.E0,0.E0,1.E0)); -#3123=VECTOR('',#3122,1.6875E-1); -#3124=CARTESIAN_POINT('',(3.E0,1.55E0,8.274999928474E0)); -#3125=LINE('',#3124,#3123); -#3126=DIRECTION('',(2.213219704028E-1,0.E0,9.752007923587E-1)); -#3127=VECTOR('',#3126,9.613412156775E-2); -#3128=CARTESIAN_POINT('',(3.E0,1.55E0,8.443749928474E0)); -#3129=LINE('',#3128,#3127); -#3130=DIRECTION('',(4.934797295212E-1,0.E0,8.697572974984E-1)); -#3131=VECTOR('',#3130,8.623087002563E-2); -#3132=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.5375E0)); -#3133=LINE('',#3132,#3131); -#3134=DIRECTION('',(7.502480356172E-1,0.E0,6.611564754674E-1)); -#3135=VECTOR('',#3134,1.134376483415E-1); -#3136=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.612499928474E0)); -#3137=LINE('',#3136,#3135); -#3138=DIRECTION('',(9.151037696758E-1,0.E0,4.032184156573E-1)); -#3139=VECTOR('',#3138,9.300188203072E-2); -#3140=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.687499964237E0)); -#3141=LINE('',#3140,#3139); -#3142=DIRECTION('',(9.848208411886E-1,0.E0,1.735739345656E-1)); -#3143=VECTOR('',#3142,1.080227196632E-1); -#3144=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,8.725000035763E0)); -#3145=LINE('',#3144,#3143); -#3146=DIRECTION('',(1.E0,0.E0,0.E0)); -#3147=VECTOR('',#3146,3.191489279270E-1); -#3148=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.743749964237E0)); -#3149=LINE('',#3148,#3147); -#3150=DIRECTION('',(9.848208245646E-1,0.E0,-1.735740288863E-1)); -#3151=VECTOR('',#3150,1.080226609633E-1); -#3152=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.743749964237E0)); -#3153=LINE('',#3152,#3151); -#3154=DIRECTION('',(9.151037957258E-1,0.E0,-4.032183565367E-1)); -#3155=VECTOR('',#3154,9.300189566683E-2); -#3156=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,8.725000035763E0)); -#3157=LINE('',#3156,#3155); -#3158=DIRECTION('',(7.502480643277E-1,0.E0,-6.611564428881E-1)); -#3159=VECTOR('',#3158,1.134376539313E-1); -#3160=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.687499964237E0)); -#3161=LINE('',#3160,#3159); -#3162=DIRECTION('',(4.934797785425E-1,0.E0,-8.697572696849E-1)); -#3163=VECTOR('',#3162,8.623087278316E-2); -#3164=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.612499928474E0)); -#3165=LINE('',#3164,#3163); -#3166=DIRECTION('',(2.213219888292E-1,0.E0,-9.752007881768E-1)); -#3167=VECTOR('',#3166,9.613412197999E-2); -#3168=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.5375E0)); -#3169=LINE('',#3168,#3167); -#3170=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3171=VECTOR('',#3170,1.6875E-1); -#3172=CARTESIAN_POINT('',(4.E0,1.55E0,8.443749928474E0)); -#3173=LINE('',#3172,#3171); -#3174=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#3175=VECTOR('',#3174,9.613391272461E-2); -#3176=CARTESIAN_POINT('',(4.E0,1.55E0,8.274999928474E0)); -#3177=LINE('',#3176,#3175); -#3178=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#3179=VECTOR('',#3178,8.623105941289E-2); -#3180=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.181250071526E0)); -#3181=LINE('',#3180,#3179); -#3182=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#3183=VECTOR('',#3182,1.134375829969E-1); -#3184=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.106249928474E0)); -#3185=LINE('',#3184,#3183); -#3186=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#3187=VECTOR('',#3186,1.080226756383E-1); -#3188=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.03125E0)); -#3189=LINE('',#3188,#3187); -#3190=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3191=VECTOR('',#3190,1.E0); -#3192=CARTESIAN_POINT('',(4.E0,1.55E0,7.75E0)); -#3193=LINE('',#3192,#3191); -#3194=DIRECTION('',(0.E0,0.E0,1.E0)); -#3195=VECTOR('',#3194,1.125E-1); -#3196=CARTESIAN_POINT('',(3.E0,1.55E0,7.75E0)); -#3197=LINE('',#3196,#3195); -#3198=DIRECTION('',(1.E0,0.E0,0.E0)); -#3199=VECTOR('',#3198,1.E0); -#3200=CARTESIAN_POINT('',(3.E0,1.55E0,7.8625E0)); -#3201=LINE('',#3200,#3199); -#3202=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3203=VECTOR('',#3202,1.125E-1); -#3204=CARTESIAN_POINT('',(4.E0,1.55E0,7.8625E0)); -#3205=LINE('',#3204,#3203); -#3206=DIRECTION('',(0.E0,0.E0,1.E0)); -#3207=VECTOR('',#3206,4.5E-1); -#3208=CARTESIAN_POINT('',(3.E0,1.55E0,7.149999928474E0)); -#3209=LINE('',#3208,#3207); -#3210=DIRECTION('',(1.E0,0.E0,0.E0)); -#3211=VECTOR('',#3210,1.E0); -#3212=CARTESIAN_POINT('',(3.E0,1.55E0,7.599999928474E0)); -#3213=LINE('',#3212,#3211); -#3214=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3215=VECTOR('',#3214,4.5E-1); -#3216=CARTESIAN_POINT('',(4.E0,1.55E0,7.599999928474E0)); -#3217=LINE('',#3216,#3215); -#3218=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#3219=VECTOR('',#3218,9.613391272461E-2); -#3220=CARTESIAN_POINT('',(4.E0,1.55E0,7.149999928474E0)); -#3221=LINE('',#3220,#3219); -#3222=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#3223=VECTOR('',#3222,8.623105941289E-2); -#3224=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,7.056250071526E0)); -#3225=LINE('',#3224,#3223); -#3226=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#3227=VECTOR('',#3226,1.134375829969E-1); -#3228=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,6.981249928474E0)); -#3229=LINE('',#3228,#3227); -#3230=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#3231=VECTOR('',#3230,9.300189566683E-2); -#3232=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.90625E0)); -#3233=LINE('',#3232,#3231); -#3234=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#3235=VECTOR('',#3234,1.080226609633E-1); -#3236=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,6.868749928474E0)); -#3237=LINE('',#3236,#3235); -#3238=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3239=VECTOR('',#3238,3.191489279270E-1); -#3240=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.85E0)); -#3241=LINE('',#3240,#3239); -#3242=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345656E-1)); -#3243=VECTOR('',#3242,1.080227196632E-1); -#3244=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.85E0)); -#3245=LINE('',#3244,#3243); -#3246=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#3247=VECTOR('',#3246,9.300188203072E-2); -#3248=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,6.868749928474E0)); -#3249=LINE('',#3248,#3247); -#3250=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#3251=VECTOR('',#3250,1.134375774071E-1); -#3252=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,6.90625E0)); -#3253=LINE('',#3252,#3251); -#3254=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#3255=VECTOR('',#3254,8.623105665537E-2); -#3256=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,6.981249928474E0)); -#3257=LINE('',#3256,#3255); -#3258=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#3259=VECTOR('',#3258,9.613391231237E-2); -#3260=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,7.056250071526E0)); -#3261=LINE('',#3260,#3259); -#3262=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3263=VECTOR('',#3262,3.375E-1); -#3264=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.487499928474E0)); -#3265=LINE('',#3264,#3263); -#3266=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#3267=VECTOR('',#3266,7.795949390370E-2); -#3268=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.149999928474E0)); -#3269=LINE('',#3268,#3267); -#3270=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#3271=VECTOR('',#3270,7.053251855852E-2); -#3272=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,7.075E0)); -#3273=LINE('',#3272,#3271); -#3274=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#3275=VECTOR('',#3274,7.403042442468E-2); -#3276=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,7.01875E0)); -#3277=LINE('',#3276,#3275); -#3278=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#3279=VECTOR('',#3278,8.714731501675E-2); -#3280=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,6.981249928474E0)); -#3281=LINE('',#3280,#3279); -#3282=DIRECTION('',(1.E0,0.E0,0.E0)); -#3283=VECTOR('',#3282,3.191489279270E-1); -#3284=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.9625E0)); -#3285=LINE('',#3284,#3283); -#3286=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#3287=VECTOR('',#3286,8.714731501675E-2); -#3288=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.9625E0)); -#3289=LINE('',#3288,#3287); -#3290=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117766E-1)); -#3291=VECTOR('',#3290,7.403037303291E-2); -#3292=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,6.981249928474E0)); -#3293=LINE('',#3292,#3291); -#3294=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#3295=VECTOR('',#3294,7.053252754859E-2); -#3296=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,7.01875E0)); -#3297=LINE('',#3296,#3295); -#3298=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#3299=VECTOR('',#3298,7.795949390370E-2); -#3300=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,7.075E0)); -#3301=LINE('',#3300,#3299); -#3302=DIRECTION('',(0.E0,0.E0,1.E0)); -#3303=VECTOR('',#3302,3.375E-1); -#3304=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.149999928474E0)); -#3305=LINE('',#3304,#3303); -#3306=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3307=VECTOR('',#3306,7.446808665991E-1); -#3308=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.487499928474E0)); -#3309=LINE('',#3308,#3307); -#3310=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3311=VECTOR('',#3310,1.063829809427E-1); -#3312=CARTESIAN_POINT('',(4.E0,1.55E0,6.606249856949E0)); -#3313=LINE('',#3312,#3311); -#3314=DIRECTION('',(0.E0,0.E0,1.E0)); -#3315=VECTOR('',#3314,9.375028610230E-2); -#3316=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.606249856949E0)); -#3317=LINE('',#3316,#3315); -#3318=DIRECTION('',(1.E0,0.E0,0.E0)); -#3319=VECTOR('',#3318,1.063829809427E-1); -#3320=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.700000143051E0)); -#3321=LINE('',#3320,#3319); -#3322=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3323=VECTOR('',#3322,9.375028610230E-2); -#3324=CARTESIAN_POINT('',(4.E0,1.55E0,6.700000143051E0)); -#3325=LINE('',#3324,#3323); -#3326=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3327=VECTOR('',#3326,1.063829660416E-1); -#3328=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.606249856949E0)); -#3329=LINE('',#3328,#3327); -#3330=DIRECTION('',(0.E0,0.E0,1.E0)); -#3331=VECTOR('',#3330,9.375028610230E-2); -#3332=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.606249856949E0)); -#3333=LINE('',#3332,#3331); -#3334=DIRECTION('',(1.E0,0.E0,0.E0)); -#3335=VECTOR('',#3334,1.063829660416E-1); -#3336=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.700000143051E0)); -#3337=LINE('',#3336,#3335); -#3338=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3339=VECTOR('',#3338,9.375028610230E-2); -#3340=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.700000143051E0)); -#3341=LINE('',#3340,#3339); -#3342=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3343=VECTOR('',#3342,1.125E-1); -#3344=CARTESIAN_POINT('',(4.E0,1.55E0,5.818749856949E0)); -#3345=LINE('',#3344,#3343); -#3346=DIRECTION('',(-8.482958127554E-1,0.E0,5.295226284698E-1)); -#3347=VECTOR('',#3346,6.019578181643E-1); -#3348=CARTESIAN_POINT('',(4.E0,1.55E0,5.706249856949E0)); -#3349=LINE('',#3348,#3347); -#3350=DIRECTION('',(-8.379227905164E-1,0.E0,-5.457887843600E-1)); -#3351=VECTOR('',#3350,5.840176552475E-1); -#3352=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.025000143051E0)); -#3353=LINE('',#3352,#3351); -#3354=DIRECTION('',(0.E0,0.E0,1.E0)); -#3355=VECTOR('',#3354,1.125E-1); -#3356=CARTESIAN_POINT('',(3.E0,1.55E0,5.706249856949E0)); -#3357=LINE('',#3356,#3355); -#3358=DIRECTION('',(8.386953909536E-1,0.E0,5.446008090273E-1)); -#3359=VECTOR('',#3358,4.820049506925E-1); -#3360=CARTESIAN_POINT('',(3.E0,1.55E0,5.818749856949E0)); -#3361=LINE('',#3360,#3359); -#3362=DIRECTION('',(-8.386957976250E-1,0.E0,5.446001827453E-1)); -#3363=VECTOR('',#3362,4.820047169753E-1); -#3364=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.081250143051E0)); -#3365=LINE('',#3364,#3363); -#3366=DIRECTION('',(0.E0,0.E0,1.E0)); -#3367=VECTOR('',#3366,1.125E-1); -#3368=CARTESIAN_POINT('',(3.E0,1.55E0,6.34375E0)); -#3369=LINE('',#3368,#3367); -#3370=DIRECTION('',(8.379231265752E-1,0.E0,-5.457882684251E-1)); -#3371=VECTOR('',#3370,5.840174210205E-1); -#3372=CARTESIAN_POINT('',(3.E0,1.55E0,6.45625E0)); -#3373=LINE('',#3372,#3371); -#3374=DIRECTION('',(8.482961329975E-1,0.E0,5.295221154414E-1)); -#3375=VECTOR('',#3374,6.019575909179E-1); -#3376=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.137500143051E0)); -#3377=LINE('',#3376,#3375); -#3378=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3379=VECTOR('',#3378,1.125E-1); -#3380=CARTESIAN_POINT('',(4.E0,1.55E0,6.45625E0)); -#3381=LINE('',#3380,#3379); -#3382=DIRECTION('',(-8.386957976250E-1,0.E0,-5.446001827453E-1)); -#3383=VECTOR('',#3382,4.820047169753E-1); -#3384=CARTESIAN_POINT('',(4.E0,1.55E0,6.34375E0)); -#3385=LINE('',#3384,#3383); -#3386=DIRECTION('',(8.386953909536E-1,0.E0,-5.446008090273E-1)); -#3387=VECTOR('',#3386,4.820049506925E-1); -#3388=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.081250143051E0)); -#3389=LINE('',#3388,#3387); -#3390=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#3391=VECTOR('',#3390,4.311534169801E-2); -#3392=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.406250143051E0)); -#3393=LINE('',#3392,#3391); -#3394=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#3395=VECTOR('',#3394,9.848483245993E-2); -#3396=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,5.44375E0)); -#3397=LINE('',#3396,#3395); -#3398=DIRECTION('',(9.431212613662E-1,0.E0,3.324489229327E-1)); -#3399=VECTOR('',#3398,1.127988522810E-1); -#3400=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,5.518750143051E0)); -#3401=LINE('',#3400,#3399); -#3402=DIRECTION('',(1.E0,0.E0,0.E0)); -#3403=VECTOR('',#3402,6.382977962494E-2); -#3404=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.55625E0)); -#3405=LINE('',#3404,#3403); -#3406=DIRECTION('',(9.431212467657E-1,0.E0,-3.324489643525E-1)); -#3407=VECTOR('',#3406,1.127988382274E-1); -#3408=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.55625E0)); -#3409=LINE('',#3408,#3407); -#3410=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#3411=VECTOR('',#3410,8.507822411232E-2); -#3412=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,5.518750143051E0)); -#3413=LINE('',#3412,#3411); -#3414=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#3415=VECTOR('',#3414,1.134167431404E-1); -#3416=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,5.462500143051E0)); -#3417=LINE('',#3416,#3415); -#3418=DIRECTION('',(2.213224705823E-1,0.E0,-9.752006788427E-1)); -#3419=VECTOR('',#3418,9.613391272461E-2); -#3420=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.368749856949E0)); -#3421=LINE('',#3420,#3419); -#3422=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3423=VECTOR('',#3422,1.125E-1); -#3424=CARTESIAN_POINT('',(4.E0,1.55E0,5.275E0)); -#3425=LINE('',#3424,#3423); -#3426=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#3427=VECTOR('',#3426,9.613391272461E-2); -#3428=CARTESIAN_POINT('',(4.E0,1.55E0,5.1625E0)); -#3429=LINE('',#3428,#3427); -#3430=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#3431=VECTOR('',#3430,1.134167431404E-1); -#3432=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.068750143051E0)); -#3433=LINE('',#3432,#3431); -#3434=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#3435=VECTOR('',#3434,8.507822411232E-2); -#3436=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,4.974999856949E0)); -#3437=LINE('',#3436,#3435); -#3438=DIRECTION('',(-9.431212467657E-1,0.E0,-3.324489643525E-1)); -#3439=VECTOR('',#3438,1.127988382274E-1); -#3440=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,4.918749856949E0)); -#3441=LINE('',#3440,#3439); -#3442=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3443=VECTOR('',#3442,6.382977962494E-2); -#3444=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.88125E0)); -#3445=LINE('',#3444,#3443); -#3446=DIRECTION('',(-9.431212613662E-1,0.E0,3.324489229327E-1)); -#3447=VECTOR('',#3446,1.127988522810E-1); -#3448=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.88125E0)); -#3449=LINE('',#3448,#3447); -#3450=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#3451=VECTOR('',#3450,9.848483245993E-2); -#3452=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,4.918749856949E0)); -#3453=LINE('',#3452,#3451); -#3454=DIRECTION('',(-4.934807975625E-1,0.E0,8.697566915162E-1)); -#3455=VECTOR('',#3454,4.311534169801E-2); -#3456=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,4.99375E0)); -#3457=LINE('',#3456,#3455); -#3458=DIRECTION('',(-4.934807975625E-1,0.E0,-8.697566915162E-1)); -#3459=VECTOR('',#3458,4.311534169801E-2); -#3460=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.031249856949E0)); -#3461=LINE('',#3460,#3459); -#3462=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#3463=VECTOR('',#3462,8.507821852253E-2); -#3464=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,4.99375E0)); -#3465=LINE('',#3464,#3463); -#3466=DIRECTION('',(-9.151046210116E-1,0.E0,-4.032164835459E-1)); -#3467=VECTOR('',#3466,9.300179550964E-2); -#3468=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,4.9375E0)); -#3469=LINE('',#3468,#3467); -#3470=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3471=VECTOR('',#3470,6.382977962494E-2); -#3472=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,4.900000143051E0)); -#3473=LINE('',#3472,#3471); -#3474=DIRECTION('',(-9.431212905670E-1,0.E0,3.324488400931E-1)); -#3475=VECTOR('',#3474,1.127988803882E-1); -#3476=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.900000143051E0)); -#3477=LINE('',#3476,#3475); -#3478=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#3479=VECTOR('',#3478,8.507821852253E-2); -#3480=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,4.9375E0)); -#3481=LINE('',#3480,#3479); -#3482=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#3483=VECTOR('',#3482,1.134163852576E-1); -#3484=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,4.99375E0)); -#3485=LINE('',#3484,#3483); -#3486=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#3487=VECTOR('',#3486,9.613433082315E-2); -#3488=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.087499856949E0)); -#3489=LINE('',#3488,#3487); -#3490=DIRECTION('',(0.E0,0.E0,1.E0)); -#3491=VECTOR('',#3490,7.499971389771E-2); -#3492=CARTESIAN_POINT('',(3.E0,1.55E0,5.181250143051E0)); -#3493=LINE('',#3492,#3491); -#3494=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#3495=VECTOR('',#3494,9.613433082315E-2); -#3496=CARTESIAN_POINT('',(3.E0,1.55E0,5.256249856949E0)); -#3497=LINE('',#3496,#3495); -#3498=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#3499=VECTOR('',#3498,1.134163852576E-1); -#3500=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.350000143051E0)); -#3501=LINE('',#3500,#3499); -#3502=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#3503=VECTOR('',#3502,8.507821852253E-2); -#3504=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,5.44375E0)); -#3505=LINE('',#3504,#3503); -#3506=DIRECTION('',(9.431212905670E-1,0.E0,3.324488400931E-1)); -#3507=VECTOR('',#3506,1.127988803882E-1); -#3508=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.5E0)); -#3509=LINE('',#3508,#3507); -#3510=DIRECTION('',(1.E0,0.E0,0.E0)); -#3511=VECTOR('',#3510,6.382977962494E-2); -#3512=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.537499856949E0)); -#3513=LINE('',#3512,#3511); -#3514=DIRECTION('',(9.151046210116E-1,0.E0,-4.032164835459E-1)); -#3515=VECTOR('',#3514,9.300179550964E-2); -#3516=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,5.537499856949E0)); -#3517=LINE('',#3516,#3515); -#3518=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#3519=VECTOR('',#3518,8.507821852253E-2); -#3520=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,5.5E0)); -#3521=LINE('',#3520,#3519); -#3522=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#3523=VECTOR('',#3522,4.311534169801E-2); -#3524=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,5.44375E0)); -#3525=LINE('',#3524,#3523); -#3526=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#3527=VECTOR('',#3526,7.795970033450E-2); -#3528=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.256249856949E0)); -#3529=LINE('',#3528,#3527); -#3530=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#3531=VECTOR('',#3530,8.623105665537E-2); -#3532=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.33125E0)); -#3533=LINE('',#3532,#3531); -#3534=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654784E-1)); -#3535=VECTOR('',#3534,1.020154877124E-1); -#3536=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.406250143051E0)); -#3537=LINE('',#3536,#3535); -#3538=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3539=VECTOR('',#3538,6.382977962494E-2); -#3540=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.462500143051E0)); -#3541=LINE('',#3540,#3539); -#3542=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#3543=VECTOR('',#3542,1.020155001437E-1); -#3544=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.462500143051E0)); -#3545=LINE('',#3544,#3543); -#3546=DIRECTION('',(-4.934786614838E-1,0.E0,-8.697579034767E-1)); -#3547=VECTOR('',#3546,8.623105665537E-2); -#3548=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.406250143051E0)); -#3549=LINE('',#3548,#3547); -#3550=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#3551=VECTOR('',#3550,7.795970033450E-2); -#3552=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.33125E0)); -#3553=LINE('',#3552,#3551); -#3554=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3555=VECTOR('',#3554,7.499971389771E-2); -#3556=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.256249856949E0)); -#3557=LINE('',#3556,#3555); -#3558=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#3559=VECTOR('',#3558,7.795970033450E-2); -#3560=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.181250143051E0)); -#3561=LINE('',#3560,#3559); -#3562=DIRECTION('',(4.934786614838E-1,0.E0,-8.697579034767E-1)); -#3563=VECTOR('',#3562,8.623105665537E-2); -#3564=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.10625E0)); -#3565=LINE('',#3564,#3563); -#3566=DIRECTION('',(8.342497220099E-1,0.E0,-5.513867982882E-1)); -#3567=VECTOR('',#3566,1.020155001437E-1); -#3568=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.031249856949E0)); -#3569=LINE('',#3568,#3567); -#3570=DIRECTION('',(1.E0,0.E0,0.E0)); -#3571=VECTOR('',#3570,6.382977962494E-2); -#3572=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.974999856949E0)); -#3573=LINE('',#3572,#3571); -#3574=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654784E-1)); -#3575=VECTOR('',#3574,1.020154877124E-1); -#3576=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.974999856949E0)); -#3577=LINE('',#3576,#3575); -#3578=DIRECTION('',(4.934786614838E-1,0.E0,8.697579034767E-1)); -#3579=VECTOR('',#3578,8.623105665537E-2); -#3580=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.031249856949E0)); -#3581=LINE('',#3580,#3579); -#3582=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#3583=VECTOR('',#3582,7.795970033450E-2); -#3584=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.10625E0)); -#3585=LINE('',#3584,#3583); -#3586=DIRECTION('',(0.E0,0.E0,1.E0)); -#3587=VECTOR('',#3586,7.499971389771E-2); -#3588=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.181250143051E0)); -#3589=LINE('',#3588,#3587); -#3590=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#3591=VECTOR('',#3590,7.795970033450E-2); -#3592=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.181250143051E0)); -#3593=LINE('',#3592,#3591); -#3594=DIRECTION('',(6.481178678037E-1,0.E0,-7.615400379714E-1)); -#3595=VECTOR('',#3594,9.848483245993E-2); -#3596=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.10625E0)); -#3597=LINE('',#3596,#3595); -#3598=DIRECTION('',(8.622121707728E-1,0.E0,-5.065473053637E-1)); -#3599=VECTOR('',#3598,7.403031573118E-2); -#3600=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.031249856949E0)); -#3601=LINE('',#3600,#3599); -#3602=DIRECTION('',(1.E0,0.E0,-2.087219535111E-14)); -#3603=VECTOR('',#3602,4.255318641663E-2); -#3604=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.99375E0)); -#3605=LINE('',#3604,#3603); -#3606=DIRECTION('',(8.622119641820E-1,0.E0,5.065476570090E-1)); -#3607=VECTOR('',#3606,7.403026433934E-2); -#3608=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,4.99375E0)); -#3609=LINE('',#3608,#3607); -#3610=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#3611=VECTOR('',#3610,9.848483245993E-2); -#3612=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.031249856949E0)); -#3613=LINE('',#3612,#3611); -#3614=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#3615=VECTOR('',#3614,7.795970033450E-2); -#3616=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.10625E0)); -#3617=LINE('',#3616,#3615); -#3618=DIRECTION('',(0.E0,0.E0,1.E0)); -#3619=VECTOR('',#3618,7.499971389771E-2); -#3620=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.181250143051E0)); -#3621=LINE('',#3620,#3619); -#3622=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#3623=VECTOR('',#3622,7.795970033450E-2); -#3624=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.256249856949E0)); -#3625=LINE('',#3624,#3623); -#3626=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#3627=VECTOR('',#3626,9.848483245993E-2); -#3628=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.33125E0)); -#3629=LINE('',#3628,#3627); -#3630=DIRECTION('',(-8.622119641821E-1,0.E0,5.065476570090E-1)); -#3631=VECTOR('',#3630,7.403026433934E-2); -#3632=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.406250143051E0)); -#3633=LINE('',#3632,#3631); -#3634=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3635=VECTOR('',#3634,4.255318641663E-2); -#3636=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,5.44375E0)); -#3637=LINE('',#3636,#3635); -#3638=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#3639=VECTOR('',#3638,7.403031573118E-2); -#3640=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.44375E0)); -#3641=LINE('',#3640,#3639); -#3642=DIRECTION('',(-6.481178678037E-1,0.E0,-7.615400379714E-1)); -#3643=VECTOR('',#3642,9.848483245993E-2); -#3644=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.406250143051E0)); -#3645=LINE('',#3644,#3643); -#3646=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#3647=VECTOR('',#3646,7.795970033450E-2); -#3648=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.33125E0)); -#3649=LINE('',#3648,#3647); -#3650=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3651=VECTOR('',#3650,7.499971389771E-2); -#3652=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.256249856949E0)); -#3653=LINE('',#3652,#3651); -#3654=DIRECTION('',(-9.832219306424E-1,0.E0,-1.824133632822E-1)); -#3655=VECTOR('',#3654,8.223073915743E-1); -#3656=CARTESIAN_POINT('',(4.E0,1.55E0,4.43125E0)); -#3657=LINE('',#3656,#3655); -#3658=DIRECTION('',(9.832218370399E-1,0.E0,-1.824138678057E-1)); -#3659=VECTOR('',#3658,8.223074698577E-1); -#3660=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,4.281250143051E0)); -#3661=LINE('',#3660,#3659); -#3662=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3663=VECTOR('',#3662,1.499998569489E-1); -#3664=CARTESIAN_POINT('',(4.E0,1.55E0,4.131249856949E0)); -#3665=LINE('',#3664,#3663); -#3666=DIRECTION('',(-9.889363736216E-1,0.E0,-1.483403145748E-1)); -#3667=VECTOR('',#3666,1.011187399588E0); -#3668=CARTESIAN_POINT('',(4.E0,1.55E0,3.98125E0)); -#3669=LINE('',#3668,#3667); -#3670=DIRECTION('',(0.E0,0.E0,1.E0)); -#3671=VECTOR('',#3670,1.125E-1); -#3672=CARTESIAN_POINT('',(3.E0,1.55E0,3.831250143051E0)); -#3673=LINE('',#3672,#3671); -#3674=DIRECTION('',(9.893852990515E-1,0.E0,1.453159661591E-1)); -#3675=VECTOR('',#3674,7.741750818822E-1); -#3676=CARTESIAN_POINT('',(3.E0,1.55E0,3.943750143051E0)); -#3677=LINE('',#3676,#3675); -#3678=DIRECTION('',(-9.813591732907E-1,0.E0,1.921826553002E-1)); -#3679=VECTOR('',#3678,7.805067357121E-1); -#3680=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.056250143051E0)); -#3681=LINE('',#3680,#3679); -#3682=DIRECTION('',(0.E0,0.E0,1.E0)); -#3683=VECTOR('',#3682,1.499998569489E-1); -#3684=CARTESIAN_POINT('',(3.E0,1.55E0,4.20625E0)); -#3685=LINE('',#3684,#3683); -#3686=DIRECTION('',(9.813590695907E-1,0.E0,1.921831848318E-1)); -#3687=VECTOR('',#3686,7.805068181881E-1); -#3688=CARTESIAN_POINT('',(3.E0,1.55E0,4.356249856949E0)); -#3689=LINE('',#3688,#3687); -#3690=DIRECTION('',(-9.893852990515E-1,0.E0,1.453159661591E-1)); -#3691=VECTOR('',#3690,7.741750818822E-1); -#3692=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.506250143051E0)); -#3693=LINE('',#3692,#3691); -#3694=DIRECTION('',(0.E0,0.E0,1.E0)); -#3695=VECTOR('',#3694,1.125E-1); -#3696=CARTESIAN_POINT('',(3.E0,1.55E0,4.618750143051E0)); -#3697=LINE('',#3696,#3695); -#3698=DIRECTION('',(9.889363113616E-1,0.E0,-1.483407296412E-1)); -#3699=VECTOR('',#3698,1.011187463248E0); -#3700=CARTESIAN_POINT('',(3.E0,1.55E0,4.731250143051E0)); -#3701=LINE('',#3700,#3699); -#3702=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3703=VECTOR('',#3702,1.499998569489E-1); -#3704=CARTESIAN_POINT('',(4.E0,1.55E0,4.581249856949E0)); -#3705=LINE('',#3704,#3703); -#3706=DIRECTION('',(-4.934850697662E-1,0.E0,-8.697542675479E-1)); -#3707=VECTOR('',#3706,4.311496843946E-2); -#3708=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,3.099999713898E0)); -#3709=LINE('',#3708,#3707); -#3710=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#3711=VECTOR('',#3710,1.020154752811E-1); -#3712=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,3.062500286102E0)); -#3713=LINE('',#3712,#3711); -#3714=DIRECTION('',(-9.594585993946E-1,0.E0,-2.818495982749E-1)); -#3715=VECTOR('',#3714,6.652687220190E-2); -#3716=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,3.006250286102E0)); -#3717=LINE('',#3716,#3715); -#3718=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3719=VECTOR('',#3718,8.510643243790E-2); -#3720=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,2.987499713898E0)); -#3721=LINE('',#3720,#3719); -#3722=DIRECTION('',(-9.594585993946E-1,0.E0,2.818495982749E-1)); -#3723=VECTOR('',#3722,6.652687220190E-2); -#3724=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.987499713898E0)); -#3725=LINE('',#3724,#3723); -#3726=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#3727=VECTOR('',#3726,1.020154752811E-1); -#3728=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,3.006250286102E0)); -#3729=LINE('',#3728,#3727); -#3730=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#3731=VECTOR('',#3730,9.848450564280E-2); -#3732=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,3.062500286102E0)); -#3733=LINE('',#3732,#3731); -#3734=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#3735=VECTOR('',#3734,9.613433082315E-2); -#3736=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,3.1375E0)); -#3737=LINE('',#3736,#3735); -#3738=DIRECTION('',(0.E0,0.E0,1.E0)); -#3739=VECTOR('',#3738,4.499995708466E-1); -#3740=CARTESIAN_POINT('',(3.E0,1.55E0,3.231250286102E0)); -#3741=LINE('',#3740,#3739); -#3742=DIRECTION('',(1.E0,0.E0,0.E0)); -#3743=VECTOR('',#3742,1.E0); -#3744=CARTESIAN_POINT('',(3.E0,1.55E0,3.681249856949E0)); -#3745=LINE('',#3744,#3743); -#3746=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3747=VECTOR('',#3746,4.499995708466E-1); -#3748=CARTESIAN_POINT('',(4.E0,1.55E0,3.681249856949E0)); -#3749=LINE('',#3748,#3747); -#3750=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#3751=VECTOR('',#3750,9.613433123539E-2); -#3752=CARTESIAN_POINT('',(4.E0,1.55E0,3.231250286102E0)); -#3753=LINE('',#3752,#3751); -#3754=DIRECTION('',(-6.481200514639E-1,0.E0,-7.615381795356E-1)); -#3755=VECTOR('',#3754,9.848450926445E-2); -#3756=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,3.1375E0)); -#3757=LINE('',#3756,#3755); -#3758=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#3759=VECTOR('',#3758,1.020154814968E-1); -#3760=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,3.062500286102E0)); -#3761=LINE('',#3760,#3759); -#3762=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#3763=VECTOR('',#3762,6.652688649895E-2); -#3764=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,3.006250286102E0)); -#3765=LINE('',#3764,#3763); -#3766=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3767=VECTOR('',#3766,1.063829660416E-1); -#3768=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,2.987499713898E0)); -#3769=LINE('',#3768,#3767); -#3770=DIRECTION('',(-9.594586349813E-1,0.E0,2.818494771324E-1)); -#3771=VECTOR('',#3770,6.652690079599E-2); -#3772=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,2.987499713898E0)); -#3773=LINE('',#3772,#3771); -#3774=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#3775=VECTOR('',#3774,1.020154752811E-1); -#3776=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,3.006250286102E0)); -#3777=LINE('',#3776,#3775); -#3778=DIRECTION('',(-4.934850697662E-1,0.E0,8.697542675479E-1)); -#3779=VECTOR('',#3778,4.311496843945E-2); -#3780=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,3.062500286102E0)); -#3781=LINE('',#3780,#3779); -#3782=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3783=VECTOR('',#3782,3.562501430511E-1); -#3784=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.568749856949E0)); -#3785=LINE('',#3784,#3783); -#3786=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#3787=VECTOR('',#3786,6.013947055430E-2); -#3788=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.212499713898E0)); -#3789=LINE('',#3788,#3787); -#3790=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#3791=VECTOR('',#3790,5.671843403331E-2); -#3792=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,3.156249713898E0)); -#3793=LINE('',#3792,#3791); -#3794=DIRECTION('',(9.594586705679E-1,0.E0,-2.818493559900E-1)); -#3795=VECTOR('',#3794,6.652692939009E-2); -#3796=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,3.118750286102E0)); -#3797=LINE('',#3796,#3795); -#3798=DIRECTION('',(1.E0,0.E0,0.E0)); -#3799=VECTOR('',#3798,4.255318641663E-2); -#3800=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,3.099999713898E0)); -#3801=LINE('',#3800,#3799); -#3802=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#3803=VECTOR('',#3802,6.652687220190E-2); -#3804=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,3.099999713898E0)); -#3805=LINE('',#3804,#3803); -#3806=DIRECTION('',(7.502531961943E-1,0.E0,6.611506194509E-1)); -#3807=VECTOR('',#3806,5.671843403331E-2); -#3808=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,3.118750286102E0)); -#3809=LINE('',#3808,#3807); -#3810=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#3811=VECTOR('',#3810,6.013947055430E-2); -#3812=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,3.156249713898E0)); -#3813=LINE('',#3812,#3811); -#3814=DIRECTION('',(0.E0,0.E0,1.E0)); -#3815=VECTOR('',#3814,3.562501430511E-1); -#3816=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.212499713898E0)); -#3817=LINE('',#3816,#3815); -#3818=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3819=VECTOR('',#3818,2.978723645210E-1); -#3820=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.568749856949E0)); -#3821=LINE('',#3820,#3819); -#3822=DIRECTION('',(1.E0,0.E0,0.E0)); -#3823=VECTOR('',#3822,6.382977962494E-2); -#3824=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,3.099999713898E0)); -#3825=LINE('',#3824,#3823); -#3826=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#3827=VECTOR('',#3826,6.652687220190E-2); -#3828=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,3.099999713898E0)); -#3829=LINE('',#3828,#3827); -#3830=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#3831=VECTOR('',#3830,5.671844521296E-2); -#3832=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,3.118750286102E0)); -#3833=LINE('',#3832,#3831); -#3834=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#3835=VECTOR('',#3834,6.013947055430E-2); -#3836=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,3.156249713898E0)); -#3837=LINE('',#3836,#3835); -#3838=DIRECTION('',(0.E0,0.E0,1.E0)); -#3839=VECTOR('',#3838,3.562501430511E-1); -#3840=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.212499713898E0)); -#3841=LINE('',#3840,#3839); -#3842=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3843=VECTOR('',#3842,3.191489428282E-1); -#3844=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.568749856949E0)); -#3845=LINE('',#3844,#3843); -#3846=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3847=VECTOR('',#3846,3.562501430511E-1); -#3848=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.568749856949E0)); -#3849=LINE('',#3848,#3847); -#3850=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#3851=VECTOR('',#3850,6.013947055430E-2); -#3852=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.212499713898E0)); -#3853=LINE('',#3852,#3851); -#3854=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#3855=VECTOR('',#3854,5.671843403331E-2); -#3856=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,3.156249713898E0)); -#3857=LINE('',#3856,#3855); -#3858=DIRECTION('',(9.594586349813E-1,0.E0,-2.818494771324E-1)); -#3859=VECTOR('',#3858,6.652690079599E-2); -#3860=CARTESIAN_POINT('',(3.617021262646E0,1.55E0,3.118750286102E0)); -#3861=LINE('',#3860,#3859); -#3862=DIRECTION('',(0.E0,0.E0,1.E0)); -#3863=VECTOR('',#3862,7.125002861023E-1); -#3864=CARTESIAN_POINT('',(3.E0,1.55E0,2.125E0)); -#3865=LINE('',#3864,#3863); -#3866=DIRECTION('',(1.E0,0.E0,0.E0)); -#3867=VECTOR('',#3866,1.063829660416E-1); -#3868=CARTESIAN_POINT('',(3.E0,1.55E0,2.837500286102E0)); -#3869=LINE('',#3868,#3867); -#3870=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3871=VECTOR('',#3870,3.000005722046E-1); -#3872=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.837500286102E0)); -#3873=LINE('',#3872,#3871); -#3874=DIRECTION('',(1.E0,0.E0,0.E0)); -#3875=VECTOR('',#3874,8.936170339584E-1); -#3876=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.537499713898E0)); -#3877=LINE('',#3876,#3875); -#3878=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3879=VECTOR('',#3878,1.125E-1); -#3880=CARTESIAN_POINT('',(4.E0,1.55E0,2.537499713898E0)); -#3881=LINE('',#3880,#3879); -#3882=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3883=VECTOR('',#3882,8.936170339584E-1); -#3884=CARTESIAN_POINT('',(4.E0,1.55E0,2.424999713898E0)); -#3885=LINE('',#3884,#3883); -#3886=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3887=VECTOR('',#3886,2.999997138977E-1); -#3888=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.424999713898E0)); -#3889=LINE('',#3888,#3887); -#3890=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3891=VECTOR('',#3890,1.063829660416E-1); -#3892=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.125E0)); -#3893=LINE('',#3892,#3891); -#3894=DIRECTION('',(4.934850697662E-1,0.E0,8.697542675479E-1)); -#3895=VECTOR('',#3894,4.311496843945E-2); -#3896=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.825000286102E0)); -#3897=LINE('',#3896,#3895); -#3898=DIRECTION('',(6.481157170580E-1,0.E0,7.615418683844E-1)); -#3899=VECTOR('',#3898,9.848515927785E-2); -#3900=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.862499713898E0)); -#3901=LINE('',#3900,#3899); -#3902=DIRECTION('',(9.431224542516E-1,0.E0,3.324455388278E-1)); -#3903=VECTOR('',#3902,1.127987096101E-1); -#3904=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.937500286102E0)); -#3905=LINE('',#3904,#3903); -#3906=DIRECTION('',(1.E0,0.E0,0.E0)); -#3907=VECTOR('',#3906,6.382977962494E-2); -#3908=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.974999713898E0)); -#3909=LINE('',#3908,#3907); -#3910=DIRECTION('',(9.431224396514E-1,0.E0,-3.324455802473E-1)); -#3911=VECTOR('',#3910,1.127986955565E-1); -#3912=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.974999713898E0)); -#3913=LINE('',#3912,#3911); -#3914=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#3915=VECTOR('',#3914,8.507822411232E-2); -#3916=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.937500286102E0)); -#3917=LINE('',#3916,#3915); -#3918=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#3919=VECTOR('',#3918,1.134167431404E-1); -#3920=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.881250286102E0)); -#3921=LINE('',#3920,#3919); -#3922=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#3923=VECTOR('',#3922,9.613433123539E-2); -#3924=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.7875E0)); -#3925=LINE('',#3924,#3923); -#3926=DIRECTION('',(0.E0,0.E0,-1.E0)); -#3927=VECTOR('',#3926,1.125E-1); -#3928=CARTESIAN_POINT('',(4.E0,1.55E0,1.693749713898E0)); -#3929=LINE('',#3928,#3927); -#3930=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#3931=VECTOR('',#3930,9.613349421393E-2); -#3932=CARTESIAN_POINT('',(4.E0,1.55E0,1.581249713898E0)); -#3933=LINE('',#3932,#3931); -#3934=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#3935=VECTOR('',#3934,1.134167431404E-1); -#3936=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.487500286102E0)); -#3937=LINE('',#3936,#3935); -#3938=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#3939=VECTOR('',#3938,8.507822411232E-2); -#3940=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.39375E0)); -#3941=LINE('',#3940,#3939); -#3942=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#3943=VECTOR('',#3942,1.127989808997E-1); -#3944=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.3375E0)); -#3945=LINE('',#3944,#3943); -#3946=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3947=VECTOR('',#3946,6.382977962494E-2); -#3948=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.299999713898E0)); -#3949=LINE('',#3948,#3947); -#3950=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#3951=VECTOR('',#3950,1.127989949533E-1); -#3952=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.299999713898E0)); -#3953=LINE('',#3952,#3951); -#3954=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#3955=VECTOR('',#3954,9.848450564280E-2); -#3956=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.3375E0)); -#3957=LINE('',#3956,#3955); -#3958=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#3959=VECTOR('',#3958,4.311571495761E-2); -#3960=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.412499713898E0)); -#3961=LINE('',#3960,#3959); -#3962=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#3963=VECTOR('',#3962,4.311571495761E-2); -#3964=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.45E0)); -#3965=LINE('',#3964,#3963); -#3966=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#3967=VECTOR('',#3966,8.507821852254E-2); -#3968=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.412499713898E0)); -#3969=LINE('',#3968,#3967); -#3970=DIRECTION('',(-9.151063236759E-1,0.E0,-4.032126193069E-1)); -#3971=VECTOR('',#3970,9.300162246873E-2); -#3972=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.356249713898E0)); -#3973=LINE('',#3972,#3971); -#3974=DIRECTION('',(-1.E0,0.E0,0.E0)); -#3975=VECTOR('',#3974,6.382977962494E-2); -#3976=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.318750286102E0)); -#3977=LINE('',#3976,#3975); -#3978=DIRECTION('',(-9.431224834518E-1,0.E0,3.324454559889E-1)); -#3979=VECTOR('',#3978,1.127987377173E-1); -#3980=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.318750286102E0)); -#3981=LINE('',#3980,#3979); -#3982=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#3983=VECTOR('',#3982,8.507821852254E-2); -#3984=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.356249713898E0)); -#3985=LINE('',#3984,#3983); -#3986=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#3987=VECTOR('',#3986,1.134167399956E-1); -#3988=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.412499713898E0)); -#3989=LINE('',#3988,#3987); -#3990=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#3991=VECTOR('',#3990,9.613433082315E-2); -#3992=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.50625E0)); -#3993=LINE('',#3992,#3991); -#3994=DIRECTION('',(0.E0,0.E0,1.E0)); -#3995=VECTOR('',#3994,7.499971389771E-2); -#3996=CARTESIAN_POINT('',(3.E0,1.55E0,1.600000286102E0)); -#3997=LINE('',#3996,#3995); -#3998=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#3999=VECTOR('',#3998,9.613433082315E-2); -#4000=CARTESIAN_POINT('',(3.E0,1.55E0,1.675E0)); -#4001=LINE('',#4000,#3999); -#4002=DIRECTION('',(5.627932782715E-1,0.E0,8.265976808173E-1)); -#4003=VECTOR('',#4002,1.134160305201E-1); -#4004=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.768750286102E0)); -#4005=LINE('',#4004,#4003); -#4006=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#4007=VECTOR('',#4006,8.507821852254E-2); -#4008=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.862499713898E0)); -#4009=LINE('',#4008,#4007); -#4010=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#4011=VECTOR('',#4010,1.127990230605E-1); -#4012=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.918749713898E0)); -#4013=LINE('',#4012,#4011); -#4014=DIRECTION('',(1.E0,0.E0,0.E0)); -#4015=VECTOR('',#4014,6.382977962494E-2); -#4016=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.95625E0)); -#4017=LINE('',#4016,#4015); -#4018=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#4019=VECTOR('',#4018,9.300196855221E-2); -#4020=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.95625E0)); -#4021=LINE('',#4020,#4019); -#4022=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#4023=VECTOR('',#4022,8.507821852254E-2); -#4024=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.918749713898E0)); -#4025=LINE('',#4024,#4023); -#4026=DIRECTION('',(4.934850697662E-1,0.E0,-8.697542675479E-1)); -#4027=VECTOR('',#4026,4.311496843946E-2); -#4028=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.862499713898E0)); -#4029=LINE('',#4028,#4027); -#4030=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#4031=VECTOR('',#4030,7.795928747295E-2); -#4032=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.675E0)); -#4033=LINE('',#4032,#4031); -#4034=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#4035=VECTOR('',#4034,8.623142991522E-2); -#4036=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.749999713898E0)); -#4037=LINE('',#4036,#4035); -#4038=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654785E-1)); -#4039=VECTOR('',#4038,1.020154877124E-1); -#4040=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.825000286102E0)); -#4041=LINE('',#4040,#4039); -#4042=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4043=VECTOR('',#4042,6.382977962494E-2); -#4044=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.881250286102E0)); -#4045=LINE('',#4044,#4043); -#4046=DIRECTION('',(-8.342497220098E-1,0.E0,-5.513867982882E-1)); -#4047=VECTOR('',#4046,1.020155001437E-1); -#4048=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.881250286102E0)); -#4049=LINE('',#4048,#4047); -#4050=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#4051=VECTOR('',#4050,8.623142991522E-2); -#4052=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.825000286102E0)); -#4053=LINE('',#4052,#4051); -#4054=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#4055=VECTOR('',#4054,7.795928747295E-2); -#4056=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.749999713898E0)); -#4057=LINE('',#4056,#4055); -#4058=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4059=VECTOR('',#4058,7.499971389771E-2); -#4060=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.675E0)); -#4061=LINE('',#4060,#4059); -#4062=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#4063=VECTOR('',#4062,7.796011319622E-2); -#4064=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.600000286102E0)); -#4065=LINE('',#4064,#4063); -#4066=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#4067=VECTOR('',#4066,8.623068339603E-2); -#4068=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.524999713898E0)); -#4069=LINE('',#4068,#4067); -#4070=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#4071=VECTOR('',#4070,1.020155001437E-1); -#4072=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.45E0)); -#4073=LINE('',#4072,#4071); -#4074=DIRECTION('',(1.E0,0.E0,0.E0)); -#4075=VECTOR('',#4074,6.382977962494E-2); -#4076=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.39375E0)); -#4077=LINE('',#4076,#4075); -#4078=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#4079=VECTOR('',#4078,1.020154877124E-1); -#4080=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.39375E0)); -#4081=LINE('',#4080,#4079); -#4082=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#4083=VECTOR('',#4082,8.623068339603E-2); -#4084=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.45E0)); -#4085=LINE('',#4084,#4083); -#4086=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#4087=VECTOR('',#4086,7.796011319622E-2); -#4088=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.524999713898E0)); -#4089=LINE('',#4088,#4087); -#4090=DIRECTION('',(0.E0,0.E0,1.E0)); -#4091=VECTOR('',#4090,7.499971389771E-2); -#4092=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.600000286102E0)); -#4093=LINE('',#4092,#4091); -#4094=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#4095=VECTOR('',#4094,7.796011319622E-2); -#4096=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.600000286102E0)); -#4097=LINE('',#4096,#4095); -#4098=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#4099=VECTOR('',#4098,9.848450564280E-2); -#4100=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.524999713898E0)); -#4101=LINE('',#4100,#4099); -#4102=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#4103=VECTOR('',#4102,7.403053311863E-2); -#4104=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.45E0)); -#4105=LINE('',#4104,#4103); -#4106=DIRECTION('',(1.E0,0.E0,0.E0)); -#4107=VECTOR('',#4106,4.255318641663E-2); -#4108=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.412499713898E0)); -#4109=LINE('',#4108,#4107); -#4110=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#4111=VECTOR('',#4110,7.403048172694E-2); -#4112=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.412499713898E0)); -#4113=LINE('',#4112,#4111); -#4114=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#4115=VECTOR('',#4114,9.848450564280E-2); -#4116=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.45E0)); -#4117=LINE('',#4116,#4115); -#4118=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#4119=VECTOR('',#4118,7.796011319622E-2); -#4120=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.524999713898E0)); -#4121=LINE('',#4120,#4119); -#4122=DIRECTION('',(0.E0,0.E0,1.E0)); -#4123=VECTOR('',#4122,7.499971389771E-2); -#4124=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.600000286102E0)); -#4125=LINE('',#4124,#4123); -#4126=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#4127=VECTOR('',#4126,7.795928747295E-2); -#4128=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.675E0)); -#4129=LINE('',#4128,#4127); -#4130=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#4131=VECTOR('',#4130,9.848515927785E-2); -#4132=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.749999713898E0)); -#4133=LINE('',#4132,#4131); -#4134=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#4135=VECTOR('',#4134,7.403004695359E-2); -#4136=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.825000286102E0)); -#4137=LINE('',#4136,#4135); -#4138=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4139=VECTOR('',#4138,4.255318641663E-2); -#4140=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.862499713898E0)); -#4141=LINE('',#4140,#4139); -#4142=DIRECTION('',(-8.622147026148E-1,0.E0,-5.065429958009E-1)); -#4143=VECTOR('',#4142,7.403009834559E-2); -#4144=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.862499713898E0)); -#4145=LINE('',#4144,#4143); -#4146=DIRECTION('',(-6.481157170580E-1,0.E0,-7.615418683844E-1)); -#4147=VECTOR('',#4146,9.848515927785E-2); -#4148=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.825000286102E0)); -#4149=LINE('',#4148,#4147); -#4150=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#4151=VECTOR('',#4150,7.795928747295E-2); -#4152=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.749999713898E0)); -#4153=LINE('',#4152,#4151); -#4154=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4155=VECTOR('',#4154,7.499971389771E-2); -#4156=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.675E0)); -#4157=LINE('',#4156,#4155); -#4158=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4159=VECTOR('',#4158,7.403048172694E-2); -#4160=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.312502861023E-1)); -#4161=LINE('',#4160,#4159); -#4162=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#4163=VECTOR('',#4162,6.652664459064E-2); -#4164=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,4.9375E-1)); -#4165=LINE('',#4164,#4163); -#4166=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4167=VECTOR('',#4166,8.510637283325E-2); -#4168=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.750002861023E-1)); -#4169=LINE('',#4168,#4167); -#4170=DIRECTION('',(-9.765810832111E-1,0.E0,2.151496872277E-1)); -#4171=VECTOR('',#4170,8.714729795475E-2); -#4172=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.750002861023E-1)); -#4173=LINE('',#4172,#4171); -#4174=DIRECTION('',(-8.622094323305E-1,0.E0,5.065519665348E-1)); -#4175=VECTOR('',#4174,7.403048172694E-2); -#4176=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,4.9375E-1)); -#4177=LINE('',#4176,#4175); -#4178=DIRECTION('',(-4.133183693567E-1,0.E0,9.105865832266E-1)); -#4179=VECTOR('',#4178,1.029549847563E-1); -#4180=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.312502861023E-1)); -#4181=LINE('',#4180,#4179); -#4182=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#4183=VECTOR('',#4182,9.848450564280E-2); -#4184=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.249997138977E-1)); -#4185=LINE('',#4184,#4183); -#4186=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4187=VECTOR('',#4186,7.403048172694E-2); -#4188=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.5E-1)); -#4189=LINE('',#4188,#4187); -#4190=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#4191=VECTOR('',#4190,8.714726885037E-2); -#4192=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.124997138977E-1)); -#4193=LINE('',#4192,#4191); -#4194=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4195=VECTOR('',#4194,4.255324602127E-2); -#4196=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,4.9375E-1)); -#4197=LINE('',#4196,#4195); -#4198=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#4199=VECTOR('',#4198,8.714726885037E-2); -#4200=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,4.9375E-1)); -#4201=LINE('',#4200,#4199); -#4202=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#4203=VECTOR('',#4202,1.134380030142E-1); -#4204=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.124997138977E-1)); -#4205=LINE('',#4204,#4203); -#4206=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#4207=VECTOR('',#4206,8.623068339603E-2); -#4208=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,5.875002861023E-1)); -#4209=LINE('',#4208,#4207); -#4210=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#4211=VECTOR('',#4210,1.329630806532E-1); -#4212=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,6.625E-1)); -#4213=LINE('',#4212,#4211); -#4214=DIRECTION('',(0.E0,0.E0,1.E0)); -#4215=VECTOR('',#4214,3.750028610230E-2); -#4216=CARTESIAN_POINT('',(3.E0,1.55E0,7.937497138977E-1)); -#4217=LINE('',#4216,#4215); -#4218=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#4219=VECTOR('',#4218,1.329630806532E-1); -#4220=CARTESIAN_POINT('',(3.E0,1.55E0,8.3125E-1)); -#4221=LINE('',#4220,#4219); -#4222=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#4223=VECTOR('',#4222,8.623142991522E-2); -#4224=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.624997138977E-1)); -#4225=LINE('',#4224,#4223); -#4226=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#4227=VECTOR('',#4226,1.134374355386E-1); -#4228=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,1.037500286102E0)); -#4229=LINE('',#4228,#4227); -#4230=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#4231=VECTOR('',#4230,8.714726885037E-2); -#4232=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.1125E0)); -#4233=LINE('',#4232,#4231); -#4234=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4235=VECTOR('',#4234,9.374942779541E-2); -#4236=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.131249713898E0)); -#4237=LINE('',#4236,#4235); -#4238=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4239=VECTOR('',#4238,7.403048172694E-2); -#4240=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.037500286102E0)); -#4241=LINE('',#4240,#4239); -#4242=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#4243=VECTOR('',#4242,7.053251855852E-2); -#4244=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.E0)); -#4245=LINE('',#4244,#4243); -#4246=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#4247=VECTOR('',#4246,9.613433082315E-2); -#4248=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.4375E-1)); -#4249=LINE('',#4248,#4247); -#4250=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4251=VECTOR('',#4250,7.499971389770E-2); -#4252=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,8.499997138977E-1)); -#4253=LINE('',#4252,#4251); -#4254=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#4255=VECTOR('',#4254,9.613433082315E-2); -#4256=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,7.75E-1)); -#4257=LINE('',#4256,#4255); -#4258=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#4259=VECTOR('',#4258,7.053251855852E-2); -#4260=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,6.812497138977E-1)); -#4261=LINE('',#4260,#4259); -#4262=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#4263=VECTOR('',#4262,7.403004695359E-2); -#4264=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,6.249997138977E-1)); -#4265=LINE('',#4264,#4263); -#4266=DIRECTION('',(1.E0,0.E0,0.E0)); -#4267=VECTOR('',#4266,4.255324602127E-2); -#4268=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,5.875002861023E-1)); -#4269=LINE('',#4268,#4267); -#4270=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#4271=VECTOR('',#4270,9.300162246873E-2); -#4272=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,5.875002861023E-1)); -#4273=LINE('',#4272,#4271); -#4274=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#4275=VECTOR('',#4274,5.671900150710E-2); -#4276=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,6.249997138977E-1)); -#4277=LINE('',#4276,#4275); -#4278=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#4279=VECTOR('',#4278,1.202789411086E-1); -#4280=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.625E-1)); -#4281=LINE('',#4280,#4279); -#4282=DIRECTION('',(0.E0,0.E0,1.E0)); -#4283=VECTOR('',#4282,7.499971389770E-2); -#4284=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,7.75E-1)); -#4285=LINE('',#4284,#4283); -#4286=DIRECTION('',(1.E0,0.E0,0.E0)); -#4287=VECTOR('',#4286,8.510637283325E-2); -#4288=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,8.499997138977E-1)); -#4289=LINE('',#4288,#4287); -#4290=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4291=VECTOR('',#4290,7.499971389770E-2); -#4292=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,8.499997138977E-1)); -#4293=LINE('',#4292,#4291); -#4294=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#4295=VECTOR('',#4294,1.144942942620E-1); -#4296=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,7.75E-1)); -#4297=LINE('',#4296,#4295); -#4298=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#4299=VECTOR('',#4298,7.053251855852E-2); -#4300=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,6.625E-1)); -#4301=LINE('',#4300,#4299); -#4302=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#4303=VECTOR('',#4302,9.300199582440E-2); -#4304=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.0625E-1)); -#4305=LINE('',#4304,#4303); -#4306=DIRECTION('',(1.E0,0.E0,0.E0)); -#4307=VECTOR('',#4306,8.510637283325E-2); -#4308=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.687497138977E-1)); -#4309=LINE('',#4308,#4307); -#4310=DIRECTION('',(9.150995129590E-1,0.E0,4.032280761334E-1)); -#4311=VECTOR('',#4310,4.650115732116E-2); -#4312=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,5.687497138977E-1)); -#4313=LINE('',#4312,#4311); -#4314=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#4315=VECTOR('',#4314,5.671844521296E-2); -#4316=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,5.875002861023E-1)); -#4317=LINE('',#4316,#4315); -#4318=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#4319=VECTOR('',#4318,4.311571495761E-2); -#4320=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.249997138977E-1)); -#4321=LINE('',#4320,#4319); -#4322=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#4323=VECTOR('',#4322,9.613433082315E-2); -#4324=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,6.625E-1)); -#4325=LINE('',#4324,#4323); -#4326=DIRECTION('',(0.E0,0.E0,1.E0)); -#4327=VECTOR('',#4326,1.125E-1); -#4328=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,7.562502861023E-1)); -#4329=LINE('',#4328,#4327); -#4330=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#4331=VECTOR('',#4330,9.613349380169E-2); -#4332=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,8.687502861023E-1)); -#4333=LINE('',#4332,#4331); -#4334=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#4335=VECTOR('',#4334,4.311571495761E-2); -#4336=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.624997138977E-1)); -#4337=LINE('',#4336,#4335); -#4338=DIRECTION('',(-7.502458047514E-1,0.E0,6.611590069362E-1)); -#4339=VECTOR('',#4338,5.671901268663E-2); -#4340=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.E0)); -#4341=LINE('',#4340,#4339); -#4342=DIRECTION('',(-9.151063236759E-1,0.E0,4.032126193069E-1)); -#4343=VECTOR('',#4342,4.650081123436E-2); -#4344=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,1.037500286102E0)); -#4345=LINE('',#4344,#4343); -#4346=DIRECTION('',(0.E0,0.E0,1.E0)); -#4347=VECTOR('',#4346,9.375028610230E-2); -#4348=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.05625E0)); -#4349=LINE('',#4348,#4347); -#4350=DIRECTION('',(9.594586171880E-1,0.E0,-2.818495377036E-1)); -#4351=VECTOR('',#4350,6.652688649895E-2); -#4352=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.150000286102E0)); -#4353=LINE('',#4352,#4351); -#4354=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#4355=VECTOR('',#4354,7.403004695359E-2); -#4356=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.131249713898E0)); -#4357=LINE('',#4356,#4355); -#4358=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#4359=VECTOR('',#4358,7.053252305355E-2); -#4360=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.093750286102E0)); -#4361=LINE('',#4360,#4359); -#4362=DIRECTION('',(4.934765744419E-1,0.E0,-8.697590876082E-1)); -#4363=VECTOR('',#4362,8.623143267274E-2); -#4364=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,1.037500286102E0)); -#4365=LINE('',#4364,#4363); -#4366=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#4367=VECTOR('',#4366,7.795928798130E-2); -#4368=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.624997138977E-1)); -#4369=LINE('',#4368,#4367); -#4370=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4371=VECTOR('',#4370,1.500002861023E-1); -#4372=CARTESIAN_POINT('',(4.E0,1.55E0,8.875E-1)); -#4373=LINE('',#4372,#4371); -#4374=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#4375=VECTOR('',#4374,7.795928798130E-2); -#4376=CARTESIAN_POINT('',(4.E0,1.55E0,7.374997138977E-1)); -#4377=LINE('',#4376,#4375); -#4378=DIRECTION('',(-4.934808465838E-1,0.E0,-8.697566637025E-1)); -#4379=VECTOR('',#4378,8.623068615357E-2); -#4380=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,6.625E-1)); -#4381=LINE('',#4380,#4379); -#4382=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#4383=VECTOR('',#4382,7.053252305355E-2); -#4384=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,5.875002861023E-1)); -#4385=LINE('',#4384,#4383); -#4386=DIRECTION('',(1.E0,0.E0,0.E0)); -#4387=VECTOR('',#4386,1.063829809427E-1); -#4388=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,3.25E-1)); -#4389=LINE('',#4388,#4387); -#4390=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4391=VECTOR('',#4390,6.75E-1); -#4392=CARTESIAN_POINT('',(4.E0,1.55E0,3.25E-1)); -#4393=LINE('',#4392,#4391); -#4394=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4395=VECTOR('',#4394,1.063829809427E-1); -#4396=CARTESIAN_POINT('',(4.E0,1.55E0,-3.5E-1)); -#4397=LINE('',#4396,#4395); -#4398=DIRECTION('',(0.E0,0.E0,1.E0)); -#4399=VECTOR('',#4398,5.249997138977E-1); -#4400=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,-3.5E-1)); -#4401=LINE('',#4400,#4399); -#4402=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#4403=VECTOR('',#4402,6.624424131262E-1); -#4404=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.749997138977E-1)); -#4405=LINE('',#4404,#4403); -#4406=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4407=VECTOR('',#4406,7.403048172694E-2); -#4408=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,-2.9375E-1)); -#4409=LINE('',#4408,#4407); -#4410=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#4411=VECTOR('',#4410,8.714726885037E-2); -#4412=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-3.312502861023E-1)); -#4413=LINE('',#4412,#4411); -#4414=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4415=VECTOR('',#4414,4.255324602127E-2); -#4416=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-3.5E-1)); -#4417=LINE('',#4416,#4415); -#4418=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#4419=VECTOR('',#4418,8.714726885037E-2); -#4420=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-3.5E-1)); -#4421=LINE('',#4420,#4419); -#4422=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#4423=VECTOR('',#4422,1.134380030142E-1); -#4424=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,-3.312502861023E-1)); -#4425=LINE('',#4424,#4423); -#4426=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#4427=VECTOR('',#4426,8.623068339603E-2); -#4428=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,-2.562497138977E-1)); -#4429=LINE('',#4428,#4427); -#4430=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#4431=VECTOR('',#4430,1.144942942620E-1); -#4432=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,-1.8125E-1)); -#4433=LINE('',#4432,#4431); -#4434=DIRECTION('',(0.E0,0.E0,1.E0)); -#4435=VECTOR('',#4434,7.499971389771E-2); -#4436=CARTESIAN_POINT('',(3.E0,1.55E0,-6.875E-2)); -#4437=LINE('',#4436,#4435); -#4438=DIRECTION('',(1.600177848561E-1,0.E0,9.871141314609E-1)); -#4439=VECTOR('',#4438,1.329639279E-1); -#4440=CARTESIAN_POINT('',(3.E0,1.55E0,6.249713897704E-3)); -#4441=LINE('',#4440,#4439); -#4442=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#4443=VECTOR('',#4442,8.623068339603E-2); -#4444=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.375002861023E-1)); -#4445=LINE('',#4444,#4443); -#4446=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#4447=VECTOR('',#4446,1.134374355386E-1); -#4448=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,2.125E-1)); -#4449=LINE('',#4448,#4447); -#4450=DIRECTION('',(9.765789979713E-1,0.E0,2.151591520746E-1)); -#4451=VECTOR('',#4450,8.714745351892E-2); -#4452=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,2.874997138977E-1)); -#4453=LINE('',#4452,#4451); -#4454=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4455=VECTOR('',#4454,9.375028610230E-2); -#4456=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,3.062502861023E-1)); -#4457=LINE('',#4456,#4455); -#4458=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4459=VECTOR('',#4458,7.403048172694E-2); -#4460=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.125E-1)); -#4461=LINE('',#4460,#4459); -#4462=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#4463=VECTOR('',#4462,7.053251855852E-2); -#4464=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.749997138977E-1)); -#4465=LINE('',#4464,#4463); -#4466=DIRECTION('',(-2.213234156683E-1,0.E0,-9.752004643543E-1)); -#4467=VECTOR('',#4466,9.613349380169E-2); -#4468=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.187497138977E-1)); -#4469=LINE('',#4468,#4467); -#4470=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4471=VECTOR('',#4470,7.500057220459E-2); -#4472=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.500028610229E-2)); -#4473=LINE('',#4472,#4471); -#4474=DIRECTION('',(2.213234156683E-1,0.E0,-9.752004643543E-1)); -#4475=VECTOR('',#4474,9.613349380169E-2); -#4476=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,-5.000028610230E-2)); -#4477=LINE('',#4476,#4475); -#4478=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865770E-1)); -#4479=VECTOR('',#4478,7.053251855852E-2); -#4480=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,-1.437497138977E-1)); -#4481=LINE('',#4480,#4479); -#4482=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#4483=VECTOR('',#4482,7.403048172694E-2); -#4484=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,-1.999997138977E-1)); -#4485=LINE('',#4484,#4483); -#4486=DIRECTION('',(1.E0,0.E0,0.E0)); -#4487=VECTOR('',#4486,4.255324602127E-2); -#4488=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-2.375E-1)); -#4489=LINE('',#4488,#4487); -#4490=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#4491=VECTOR('',#4490,9.300196855221E-2); -#4492=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-2.375E-1)); -#4493=LINE('',#4492,#4491); -#4494=DIRECTION('',(7.117179927714E-1,0.E0,7.024653007554E-1)); -#4495=VECTOR('',#4494,7.473674690168E-1); -#4496=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-1.999997138977E-1)); -#4497=LINE('',#4496,#4495); -#4498=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4499=VECTOR('',#4498,1.E0); -#4500=CARTESIAN_POINT('',(5.75E0,1.55E0,1.03375E1)); -#4501=LINE('',#4500,#4499); -#4502=DIRECTION('',(0.E0,0.E0,1.E0)); -#4503=VECTOR('',#4502,1.125E-1); -#4504=CARTESIAN_POINT('',(4.75E0,1.55E0,1.03375E1)); -#4505=LINE('',#4504,#4503); -#4506=DIRECTION('',(1.E0,0.E0,0.E0)); -#4507=VECTOR('',#4506,1.E0); -#4508=CARTESIAN_POINT('',(4.75E0,1.55E0,1.045E1)); -#4509=LINE('',#4508,#4507); -#4510=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4511=VECTOR('',#4510,1.125E-1); -#4512=CARTESIAN_POINT('',(5.75E0,1.55E0,1.045E1)); -#4513=LINE('',#4512,#4511); -#4514=DIRECTION('',(0.E0,0.E0,1.E0)); -#4515=VECTOR('',#4514,1.124999463558E-1); -#4516=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.456250035763E0)); -#4517=LINE('',#4516,#4515); -#4518=DIRECTION('',(9.594607799365E-1,0.E0,2.818421752748E-1)); -#4519=VECTOR('',#4518,6.652672100798E-2); -#4520=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.568749982119E0)); -#4521=LINE('',#4520,#4519); -#4522=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#4523=VECTOR('',#4522,7.053252754859E-2); -#4524=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,9.587500017881E0)); -#4525=LINE('',#4524,#4523); -#4526=DIRECTION('',(2.729183843844E-1,0.E0,9.620371902712E-1)); -#4527=VECTOR('',#4526,7.795954551139E-2); -#4528=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.643750017881E0)); -#4529=LINE('',#4528,#4527); -#4530=DIRECTION('',(0.E0,0.E0,1.E0)); -#4531=VECTOR('',#4530,1.6875E-1); -#4532=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.71875E0)); -#4533=LINE('',#4532,#4531); -#4534=DIRECTION('',(-2.729183843844E-1,0.E0,9.620371902713E-1)); -#4535=VECTOR('',#4534,7.795954551140E-2); -#4536=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.8875E0)); -#4537=LINE('',#4536,#4535); -#4538=DIRECTION('',(-6.033129662504E-1,0.E0,7.975045233440E-1)); -#4539=VECTOR('',#4538,7.053254893932E-2); -#4540=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.962499982119E0)); -#4541=LINE('',#4540,#4539); -#4542=DIRECTION('',(-8.622111729792E-1,0.E0,5.065490037399E-1)); -#4543=VECTOR('',#4542,7.403033227277E-2); -#4544=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.001875000894E1)); -#4545=LINE('',#4544,#4543); -#4546=DIRECTION('',(-9.765803560308E-1,0.E0,2.151529879292E-1)); -#4547=VECTOR('',#4546,8.714733232927E-2); -#4548=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.005625E1)); -#4549=LINE('',#4548,#4547); -#4550=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4551=VECTOR('',#4550,3.191489279270E-1); -#4552=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.007500000894E1)); -#4553=LINE('',#4552,#4551); -#4554=DIRECTION('',(-9.765803560308E-1,0.E0,-2.151529879292E-1)); -#4555=VECTOR('',#4554,8.714733232927E-2); -#4556=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.007500000894E1)); -#4557=LINE('',#4556,#4555); -#4558=DIRECTION('',(-8.622113795709E-1,0.E0,-5.065486520942E-1)); -#4559=VECTOR('',#4558,7.403038366456E-2); -#4560=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.005625E1)); -#4561=LINE('',#4560,#4559); -#4562=DIRECTION('',(-6.033128318821E-1,0.E0,-7.975046249937E-1)); -#4563=VECTOR('',#4562,7.053253994926E-2); -#4564=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.001875000894E1)); -#4565=LINE('',#4564,#4563); -#4566=DIRECTION('',(-2.729183843844E-1,0.E0,-9.620371902713E-1)); -#4567=VECTOR('',#4566,7.795954551140E-2); -#4568=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.962499982119E0)); -#4569=LINE('',#4568,#4567); -#4570=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4571=VECTOR('',#4570,1.6875E-1); -#4572=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.8875E0)); -#4573=LINE('',#4572,#4571); -#4574=DIRECTION('',(2.729183843844E-1,0.E0,-9.620371902713E-1)); -#4575=VECTOR('',#4574,7.795954551140E-2); -#4576=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.71875E0)); -#4577=LINE('',#4576,#4575); -#4578=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#4579=VECTOR('',#4578,7.053251855852E-2); -#4580=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.643750017881E0)); -#4581=LINE('',#4580,#4579); -#4582=DIRECTION('',(9.594608511063E-1,0.E0,-2.818419329952E-1)); -#4583=VECTOR('',#4582,6.652677819631E-2); -#4584=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,9.587500017881E0)); -#4585=LINE('',#4584,#4583); -#4586=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4587=VECTOR('',#4586,1.124999463558E-1); -#4588=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.568749982119E0)); -#4589=LINE('',#4588,#4587); -#4590=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#4591=VECTOR('',#4590,1.080227196632E-1); -#4592=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.456250035763E0)); -#4593=LINE('',#4592,#4591); -#4594=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#4595=VECTOR('',#4594,1.134376483415E-1); -#4596=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.474999964237E0)); -#4597=LINE('',#4596,#4595); -#4598=DIRECTION('',(-4.934794625115E-1,0.E0,8.697574489933E-1)); -#4599=VECTOR('',#4598,8.623091668305E-2); -#4600=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,9.55E0)); -#4601=LINE('',#4600,#4599); -#4602=DIRECTION('',(-2.213220908409E-1,0.E0,9.752007650252E-1)); -#4603=VECTOR('',#4602,9.613406925390E-2); -#4604=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.624999982119E0)); -#4605=LINE('',#4604,#4603); -#4606=DIRECTION('',(0.E0,0.E0,1.E0)); -#4607=VECTOR('',#4606,1.6875E-1); -#4608=CARTESIAN_POINT('',(4.75E0,1.55E0,9.71875E0)); -#4609=LINE('',#4608,#4607); -#4610=DIRECTION('',(2.213220908409E-1,0.E0,9.752007650253E-1)); -#4611=VECTOR('',#4610,9.613406925390E-2); -#4612=CARTESIAN_POINT('',(4.75E0,1.55E0,9.8875E0)); -#4613=LINE('',#4612,#4611); -#4614=DIRECTION('',(4.934794625115E-1,0.E0,8.697574489933E-1)); -#4615=VECTOR('',#4614,8.623091668305E-2); -#4616=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.981250017881E0)); -#4617=LINE('',#4616,#4615); -#4618=DIRECTION('',(7.502481529028E-1,0.E0,6.611563423775E-1)); -#4619=VECTOR('',#4618,1.134376306079E-1); -#4620=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.005625E1)); -#4621=LINE('',#4620,#4619); -#4622=DIRECTION('',(9.151040889270E-1,0.E0,4.032176911162E-1)); -#4623=VECTOR('',#4622,9.300184958527E-2); -#4624=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.013125000894E1)); -#4625=LINE('',#4624,#4623); -#4626=DIRECTION('',(9.848207138555E-1,0.E0,1.735746570245E-1)); -#4627=VECTOR('',#4626,1.080227336301E-1); -#4628=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.016875E1)); -#4629=LINE('',#4628,#4627); -#4630=DIRECTION('',(1.E0,0.E0,0.E0)); -#4631=VECTOR('',#4630,3.191489279270E-1); -#4632=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.018750000894E1)); -#4633=LINE('',#4632,#4631); -#4634=DIRECTION('',(9.848206972314E-1,0.E0,-1.735747513456E-1)); -#4635=VECTOR('',#4634,1.080226749302E-1); -#4636=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.018750000894E1)); -#4637=LINE('',#4636,#4635); -#4638=DIRECTION('',(9.151041149770E-1,0.E0,-4.032176319956E-1)); -#4639=VECTOR('',#4638,9.300186322138E-2); -#4640=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.016875E1)); -#4641=LINE('',#4640,#4639); -#4642=DIRECTION('',(7.502481816133E-1,0.E0,-6.611563097982E-1)); -#4643=VECTOR('',#4642,1.134376361977E-1); -#4644=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.013125000894E1)); -#4645=LINE('',#4644,#4643); -#4646=DIRECTION('',(4.934795115328E-1,0.E0,-8.697574211798E-1)); -#4647=VECTOR('',#4646,8.623091944058E-2); -#4648=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.005625E1)); -#4649=LINE('',#4648,#4647); -#4650=DIRECTION('',(2.213221092673E-1,0.E0,-9.752007608434E-1)); -#4651=VECTOR('',#4650,9.613406966615E-2); -#4652=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.981250017881E0)); -#4653=LINE('',#4652,#4651); -#4654=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4655=VECTOR('',#4654,1.6875E-1); -#4656=CARTESIAN_POINT('',(5.75E0,1.55E0,9.8875E0)); -#4657=LINE('',#4656,#4655); -#4658=DIRECTION('',(-2.213221092673E-1,0.E0,-9.752007608434E-1)); -#4659=VECTOR('',#4658,9.613406966615E-2); -#4660=CARTESIAN_POINT('',(5.75E0,1.55E0,9.71875E0)); -#4661=LINE('',#4660,#4659); -#4662=DIRECTION('',(-4.934795115328E-1,0.E0,-8.697574211798E-1)); -#4663=VECTOR('',#4662,8.623091944059E-2); -#4664=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.624999982119E0)); -#4665=LINE('',#4664,#4663); -#4666=DIRECTION('',(-7.502480643278E-1,0.E0,-6.611564428881E-1)); -#4667=VECTOR('',#4666,1.134376539313E-1); -#4668=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,9.55E0)); -#4669=LINE('',#4668,#4667); -#4670=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#4671=VECTOR('',#4670,1.080226756383E-1); -#4672=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.474999964237E0)); -#4673=LINE('',#4672,#4671); -#4674=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4675=VECTOR('',#4674,1.E0); -#4676=CARTESIAN_POINT('',(5.75E0,1.55E0,9.193749964237E0)); -#4677=LINE('',#4676,#4675); -#4678=DIRECTION('',(0.E0,0.E0,1.E0)); -#4679=VECTOR('',#4678,1.125E-1); -#4680=CARTESIAN_POINT('',(4.75E0,1.55E0,9.193749964237E0)); -#4681=LINE('',#4680,#4679); -#4682=DIRECTION('',(1.E0,0.E0,0.E0)); -#4683=VECTOR('',#4682,1.E0); -#4684=CARTESIAN_POINT('',(4.75E0,1.55E0,9.306249964237E0)); -#4685=LINE('',#4684,#4683); -#4686=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4687=VECTOR('',#4686,1.125E-1); -#4688=CARTESIAN_POINT('',(5.75E0,1.55E0,9.306249964237E0)); -#4689=LINE('',#4688,#4687); -#4690=DIRECTION('',(0.E0,0.E0,1.E0)); -#4691=VECTOR('',#4690,4.5E-1); -#4692=CARTESIAN_POINT('',(4.75E0,1.55E0,8.59375E0)); -#4693=LINE('',#4692,#4691); -#4694=DIRECTION('',(1.E0,0.E0,0.E0)); -#4695=VECTOR('',#4694,1.E0); -#4696=CARTESIAN_POINT('',(4.75E0,1.55E0,9.04375E0)); -#4697=LINE('',#4696,#4695); -#4698=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4699=VECTOR('',#4698,4.5E-1); -#4700=CARTESIAN_POINT('',(5.75E0,1.55E0,9.04375E0)); -#4701=LINE('',#4700,#4699); -#4702=DIRECTION('',(-2.213219888292E-1,0.E0,-9.752007881768E-1)); -#4703=VECTOR('',#4702,9.613412197999E-2); -#4704=CARTESIAN_POINT('',(5.75E0,1.55E0,8.59375E0)); -#4705=LINE('',#4704,#4703); -#4706=DIRECTION('',(-4.934797785425E-1,0.E0,-8.697572696849E-1)); -#4707=VECTOR('',#4706,8.623087278316E-2); -#4708=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,8.499999928474E0)); -#4709=LINE('',#4708,#4707); -#4710=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#4711=VECTOR('',#4710,1.134375829969E-1); -#4712=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,8.425E0)); -#4713=LINE('',#4712,#4711); -#4714=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#4715=VECTOR('',#4714,9.300189566683E-2); -#4716=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.350000071526E0)); -#4717=LINE('',#4716,#4715); -#4718=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#4719=VECTOR('',#4718,1.080226609633E-1); -#4720=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,8.3125E0)); -#4721=LINE('',#4720,#4719); -#4722=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4723=VECTOR('',#4722,3.191489279270E-1); -#4724=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.293750071526E0)); -#4725=LINE('',#4724,#4723); -#4726=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#4727=VECTOR('',#4726,1.080227196632E-1); -#4728=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.293750071526E0)); -#4729=LINE('',#4728,#4727); -#4730=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#4731=VECTOR('',#4730,9.300188203072E-2); -#4732=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,8.3125E0)); -#4733=LINE('',#4732,#4731); -#4734=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#4735=VECTOR('',#4734,1.134375774071E-1); -#4736=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.350000071526E0)); -#4737=LINE('',#4736,#4735); -#4738=DIRECTION('',(-4.934797295212E-1,0.E0,8.697572974984E-1)); -#4739=VECTOR('',#4738,8.623087002563E-2); -#4740=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,8.425E0)); -#4741=LINE('',#4740,#4739); -#4742=DIRECTION('',(-2.213219704028E-1,0.E0,9.752007923587E-1)); -#4743=VECTOR('',#4742,9.613412156775E-2); -#4744=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,8.499999928474E0)); -#4745=LINE('',#4744,#4743); -#4746=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4747=VECTOR('',#4746,3.375E-1); -#4748=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.93125E0)); -#4749=LINE('',#4748,#4747); -#4750=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#4751=VECTOR('',#4750,7.795949390370E-2); -#4752=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.59375E0)); -#4753=LINE('',#4752,#4751); -#4754=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#4755=VECTOR('',#4754,7.053251855852E-2); -#4756=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.518750071526E0)); -#4757=LINE('',#4756,#4755); -#4758=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#4759=VECTOR('',#4758,7.403042442468E-2); -#4760=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,8.462500071526E0)); -#4761=LINE('',#4760,#4759); -#4762=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#4763=VECTOR('',#4762,8.714731501675E-2); -#4764=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,8.425E0)); -#4765=LINE('',#4764,#4763); -#4766=DIRECTION('',(1.E0,0.E0,0.E0)); -#4767=VECTOR('',#4766,3.191489279270E-1); -#4768=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.406250071526E0)); -#4769=LINE('',#4768,#4767); -#4770=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#4771=VECTOR('',#4770,8.714731501675E-2); -#4772=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.406250071526E0)); -#4773=LINE('',#4772,#4771); -#4774=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117767E-1)); -#4775=VECTOR('',#4774,7.403037303291E-2); -#4776=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,8.425E0)); -#4777=LINE('',#4776,#4775); -#4778=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#4779=VECTOR('',#4778,7.053252754859E-2); -#4780=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,8.462500071526E0)); -#4781=LINE('',#4780,#4779); -#4782=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#4783=VECTOR('',#4782,7.795949390370E-2); -#4784=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.518750071526E0)); -#4785=LINE('',#4784,#4783); -#4786=DIRECTION('',(0.E0,0.E0,1.E0)); -#4787=VECTOR('',#4786,3.375E-1); -#4788=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.59375E0)); -#4789=LINE('',#4788,#4787); -#4790=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4791=VECTOR('',#4790,7.446808665991E-1); -#4792=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.93125E0)); -#4793=LINE('',#4792,#4791); -#4794=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4795=VECTOR('',#4794,1.063829809427E-1); -#4796=CARTESIAN_POINT('',(5.75E0,1.55E0,8.049999928474E0)); -#4797=LINE('',#4796,#4795); -#4798=DIRECTION('',(0.E0,0.E0,1.E0)); -#4799=VECTOR('',#4798,9.375007152557E-2); -#4800=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.049999928474E0)); -#4801=LINE('',#4800,#4799); -#4802=DIRECTION('',(1.E0,0.E0,0.E0)); -#4803=VECTOR('',#4802,1.063829809427E-1); -#4804=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.14375E0)); -#4805=LINE('',#4804,#4803); -#4806=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4807=VECTOR('',#4806,9.375007152557E-2); -#4808=CARTESIAN_POINT('',(5.75E0,1.55E0,8.14375E0)); -#4809=LINE('',#4808,#4807); -#4810=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4811=VECTOR('',#4810,1.063829660416E-1); -#4812=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.049999928474E0)); -#4813=LINE('',#4812,#4811); -#4814=DIRECTION('',(0.E0,0.E0,1.E0)); -#4815=VECTOR('',#4814,9.375007152557E-2); -#4816=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.049999928474E0)); -#4817=LINE('',#4816,#4815); -#4818=DIRECTION('',(1.E0,0.E0,0.E0)); -#4819=VECTOR('',#4818,1.063829660416E-1); -#4820=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.14375E0)); -#4821=LINE('',#4820,#4819); -#4822=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4823=VECTOR('',#4822,9.375007152557E-2); -#4824=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.14375E0)); -#4825=LINE('',#4824,#4823); -#4826=DIRECTION('',(7.872280489029E-1,0.E0,6.166619811700E-1)); -#4827=VECTOR('',#4826,7.297352743333E-1); -#4828=CARTESIAN_POINT('',(4.75E0,1.55E0,7.450000071526E0)); -#4829=LINE('',#4828,#4827); -#4830=DIRECTION('',(1.E0,0.E0,0.E0)); -#4831=VECTOR('',#4830,1.276595890522E-1); -#4832=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.900000071526E0)); -#4833=LINE('',#4832,#4831); -#4834=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4835=VECTOR('',#4834,4.5E-1); -#4836=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.900000071526E0)); -#4837=LINE('',#4836,#4835); -#4838=DIRECTION('',(1.E0,0.E0,0.E0)); -#4839=VECTOR('',#4838,2.978723347187E-1); -#4840=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.450000071526E0)); -#4841=LINE('',#4840,#4839); -#4842=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4843=VECTOR('',#4842,1.125E-1); -#4844=CARTESIAN_POINT('',(5.75E0,1.55E0,7.450000071526E0)); -#4845=LINE('',#4844,#4843); -#4846=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4847=VECTOR('',#4846,2.978723347187E-1); -#4848=CARTESIAN_POINT('',(5.75E0,1.55E0,7.337500071526E0)); -#4849=LINE('',#4848,#4847); -#4850=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4851=VECTOR('',#4850,1.875001430511E-1); -#4852=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.337500071526E0)); -#4853=LINE('',#4852,#4851); -#4854=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4855=VECTOR('',#4854,1.276595890522E-1); -#4856=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.149999928474E0)); -#4857=LINE('',#4856,#4855); -#4858=DIRECTION('',(0.E0,0.E0,1.E0)); -#4859=VECTOR('',#4858,1.875001430511E-1); -#4860=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.149999928474E0)); -#4861=LINE('',#4860,#4859); -#4862=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4863=VECTOR('',#4862,5.744680762291E-1); -#4864=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.337500071526E0)); -#4865=LINE('',#4864,#4863); -#4866=DIRECTION('',(0.E0,0.E0,1.E0)); -#4867=VECTOR('',#4866,1.125E-1); -#4868=CARTESIAN_POINT('',(4.75E0,1.55E0,7.337500071526E0)); -#4869=LINE('',#4868,#4867); -#4870=DIRECTION('',(-7.852596483189E-1,0.E0,-6.191666049797E-1)); -#4871=VECTOR('',#4870,5.148046654734E-1); -#4872=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.768749928474E0)); -#4873=LINE('',#4872,#4871); -#4874=DIRECTION('',(1.E0,0.E0,0.E0)); -#4875=VECTOR('',#4874,4.042553305626E-1); -#4876=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,7.450000071526E0)); -#4877=LINE('',#4876,#4875); -#4878=DIRECTION('',(0.E0,0.E0,1.E0)); -#4879=VECTOR('',#4878,3.187498569489E-1); -#4880=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.450000071526E0)); -#4881=LINE('',#4880,#4879); -#4882=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4883=VECTOR('',#4882,1.E0); -#4884=CARTESIAN_POINT('',(5.75E0,1.55E0,6.774999856949E0)); -#4885=LINE('',#4884,#4883); -#4886=DIRECTION('',(0.E0,0.E0,1.E0)); -#4887=VECTOR('',#4886,1.125002145767E-1); -#4888=CARTESIAN_POINT('',(4.75E0,1.55E0,6.774999856949E0)); -#4889=LINE('',#4888,#4887); -#4890=DIRECTION('',(7.979434329020E-1,0.E0,6.027323434897E-1)); -#4891=VECTOR('',#4890,1.866500134183E-1); -#4892=CARTESIAN_POINT('',(4.75E0,1.55E0,6.887500071526E0)); -#4893=LINE('',#4892,#4891); -#4894=DIRECTION('',(1.E0,0.E0,-1.565414103161E-14)); -#4895=VECTOR('',#4894,1.702128052711E-1); -#4896=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,7.000000071526E0)); -#4897=LINE('',#4896,#4895); -#4898=DIRECTION('',(-7.979435489134E-1,0.E0,-6.027321899048E-1)); -#4899=VECTOR('',#4898,1.866500609794E-1); -#4900=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,7.000000071526E0)); -#4901=LINE('',#4900,#4899); -#4902=DIRECTION('',(1.E0,0.E0,0.E0)); -#4903=VECTOR('',#4902,8.297872543335E-1); -#4904=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.887500071526E0)); -#4905=LINE('',#4904,#4903); -#4906=DIRECTION('',(0.E0,0.E0,-1.E0)); -#4907=VECTOR('',#4906,1.125002145767E-1); -#4908=CARTESIAN_POINT('',(5.75E0,1.55E0,6.887500071526E0)); -#4909=LINE('',#4908,#4907); -#4910=DIRECTION('',(1.E0,0.E0,0.E0)); -#4911=VECTOR('',#4910,1.914893388748E-1); -#4912=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.625E0)); -#4913=LINE('',#4912,#4911); -#4914=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#4915=VECTOR('',#4914,1.080227275584E-1); -#4916=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,6.625E0)); -#4917=LINE('',#4916,#4915); -#4918=DIRECTION('',(9.594620882388E-1,0.E0,-2.818377214504E-1)); -#4919=VECTOR('',#4918,6.652663029355E-2); -#4920=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.606249856949E0)); -#4921=LINE('',#4920,#4919); -#4922=DIRECTION('',(9.151029443877E-1,0.E0,-4.032202886425E-1)); -#4923=VECTOR('',#4922,9.300198218831E-2); -#4924=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,6.587500143051E0)); -#4925=LINE('',#4924,#4923); -#4926=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#4927=VECTOR('',#4926,8.507822411232E-2); -#4928=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.549999856949E0)); -#4929=LINE('',#4928,#4927); -#4930=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#4931=VECTOR('',#4930,1.134163884024E-1); -#4932=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.493749856949E0)); -#4933=LINE('',#4932,#4931); -#4934=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#4935=VECTOR('',#4934,1.144942946081E-1); -#4936=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.4E0)); -#4937=LINE('',#4936,#4935); -#4938=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#4939=VECTOR('',#4938,1.144942946081E-1); -#4940=CARTESIAN_POINT('',(5.75E0,1.55E0,6.2875E0)); -#4941=LINE('',#4940,#4939); -#4942=DIRECTION('',(-5.627915516617E-1,0.E0,-8.265988563857E-1)); -#4943=VECTOR('',#4942,1.134163884024E-1); -#4944=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.175E0)); -#4945=LINE('',#4944,#4943); -#4946=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#4947=VECTOR('',#4946,8.507822411232E-2); -#4948=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.081250143051E0)); -#4949=LINE('',#4948,#4947); -#4950=DIRECTION('',(-9.151029443877E-1,0.E0,-4.032202886425E-1)); -#4951=VECTOR('',#4950,9.300198218831E-2); -#4952=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.025000143051E0)); -#4953=LINE('',#4952,#4951); -#4954=DIRECTION('',(-9.594620882389E-1,0.E0,-2.818377214504E-1)); -#4955=VECTOR('',#4954,6.652663029354E-2); -#4956=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.987499856949E0)); -#4957=LINE('',#4956,#4955); -#4958=DIRECTION('',(-9.848204933204E-1,0.E0,-1.735759082829E-1)); -#4959=VECTOR('',#4958,1.080227275584E-1); -#4960=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.968750143051E0)); -#4961=LINE('',#4960,#4959); -#4962=DIRECTION('',(-1.E0,0.E0,0.E0)); -#4963=VECTOR('',#4962,1.914893388748E-1); -#4964=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.95E0)); -#4965=LINE('',#4964,#4963); -#4966=DIRECTION('',(-9.848204850082E-1,0.E0,1.735759554437E-1)); -#4967=VECTOR('',#4966,1.080226982085E-1); -#4968=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.95E0)); -#4969=LINE('',#4968,#4967); -#4970=DIRECTION('',(-9.594621594064E-1,0.E0,2.818374791739E-1)); -#4971=VECTOR('',#4970,6.652668748195E-2); -#4972=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.968750143051E0)); -#4973=LINE('',#4972,#4971); -#4974=DIRECTION('',(-9.151029183374E-1,0.E0,4.032203477633E-1)); -#4975=VECTOR('',#4974,9.300196855221E-2); -#4976=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.987499856949E0)); -#4977=LINE('',#4976,#4975); -#4978=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#4979=VECTOR('',#4978,8.507821852254E-2); -#4980=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.025000143051E0)); -#4981=LINE('',#4980,#4979); -#4982=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#4983=VECTOR('',#4982,1.134163852576E-1); -#4984=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.081250143051E0)); -#4985=LINE('',#4984,#4983); -#4986=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#4987=VECTOR('',#4986,1.144942942620E-1); -#4988=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.175E0)); -#4989=LINE('',#4988,#4987); -#4990=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#4991=VECTOR('',#4990,1.144942942620E-1); -#4992=CARTESIAN_POINT('',(4.75E0,1.55E0,6.2875E0)); -#4993=LINE('',#4992,#4991); -#4994=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#4995=VECTOR('',#4994,1.134163852576E-1); -#4996=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.4E0)); -#4997=LINE('',#4996,#4995); -#4998=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#4999=VECTOR('',#4998,8.507821852254E-2); -#5000=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.493749856949E0)); -#5001=LINE('',#5000,#4999); -#5002=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#5003=VECTOR('',#5002,9.300196855221E-2); -#5004=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.549999856949E0)); -#5005=LINE('',#5004,#5003); -#5006=DIRECTION('',(9.594621594064E-1,0.E0,2.818374791740E-1)); -#5007=VECTOR('',#5006,6.652668748194E-2); -#5008=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,6.587500143051E0)); -#5009=LINE('',#5008,#5007); -#5010=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554437E-1)); -#5011=VECTOR('',#5010,1.080226982085E-1); -#5012=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.606249856949E0)); -#5013=LINE('',#5012,#5011); -#5014=DIRECTION('',(-9.893851372145E-1,0.E0,-1.453170680242E-1)); -#5015=VECTOR('',#5014,1.290291863584E-1); -#5016=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.531250143051E0)); -#5017=LINE('',#5016,#5015); -#5018=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#5019=VECTOR('',#5018,1.480607974576E-1); -#5020=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.5125E0)); -#5021=LINE('',#5020,#5019); -#5022=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865771E-1)); -#5023=VECTOR('',#5022,7.053251855852E-2); -#5024=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.437499856949E0)); -#5025=LINE('',#5024,#5023); -#5026=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#5027=VECTOR('',#5026,9.613391231237E-2); -#5028=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.381249856949E0)); -#5029=LINE('',#5028,#5027); -#5030=DIRECTION('',(2.213224521559E-1,0.E0,-9.752006830246E-1)); -#5031=VECTOR('',#5030,9.613391231237E-2); -#5032=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.2875E0)); -#5033=LINE('',#5032,#5031); -#5034=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#5035=VECTOR('',#5034,7.053251855852E-2); -#5036=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.193750143051E0)); -#5037=LINE('',#5036,#5035); -#5038=DIRECTION('',(8.622108015533E-1,0.E0,-5.065496359537E-1)); -#5039=VECTOR('',#5038,1.480607974576E-1); -#5040=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.137500143051E0)); -#5041=LINE('',#5040,#5039); -#5042=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#5043=VECTOR('',#5042,1.290291863584E-1); -#5044=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.0625E0)); -#5045=LINE('',#5044,#5043); -#5046=DIRECTION('',(1.E0,0.E0,0.E0)); -#5047=VECTOR('',#5046,1.489361524582E-1); -#5048=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.043749856949E0)); -#5049=LINE('',#5048,#5047); -#5050=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#5051=VECTOR('',#5050,1.290292158444E-1); -#5052=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.043749856949E0)); -#5053=LINE('',#5052,#5051); -#5054=DIRECTION('',(8.622107240812E-1,0.E0,5.065497678209E-1)); -#5055=VECTOR('',#5054,1.480607589138E-1); -#5056=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.0625E0)); -#5057=LINE('',#5056,#5055); -#5058=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#5059=VECTOR('',#5058,7.053251855852E-2); -#5060=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.137500143051E0)); -#5061=LINE('',#5060,#5059); -#5062=DIRECTION('',(2.213224521559E-1,0.E0,9.752006830246E-1)); -#5063=VECTOR('',#5062,9.613391231237E-2); -#5064=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.193750143051E0)); -#5065=LINE('',#5064,#5063); -#5066=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#5067=VECTOR('',#5066,9.613391231237E-2); -#5068=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,6.2875E0)); -#5069=LINE('',#5068,#5067); -#5070=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865771E-1)); -#5071=VECTOR('',#5070,7.053251855852E-2); -#5072=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.381249856949E0)); -#5073=LINE('',#5072,#5071); -#5074=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#5075=VECTOR('',#5074,1.480607589138E-1); -#5076=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.437499856949E0)); -#5077=LINE('',#5076,#5075); -#5078=DIRECTION('',(-9.893851420919E-1,0.E0,1.453170348161E-1)); -#5079=VECTOR('',#5078,1.290292158444E-1); -#5080=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.5125E0)); -#5081=LINE('',#5080,#5079); -#5082=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5083=VECTOR('',#5082,1.489361524582E-1); -#5084=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.531250143051E0)); -#5085=LINE('',#5084,#5083); -#5086=DIRECTION('',(1.E0,0.E0,0.E0)); -#5087=VECTOR('',#5086,1.914893388748E-1); -#5088=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.800000143051E0)); -#5089=LINE('',#5088,#5087); -#5090=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#5091=VECTOR('',#5090,1.080227275584E-1); -#5092=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.800000143051E0)); -#5093=LINE('',#5092,#5091); -#5094=DIRECTION('',(9.594603438319E-1,0.E0,-2.818436598788E-1)); -#5095=VECTOR('',#5094,6.652675124645E-2); -#5096=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.78125E0)); -#5097=LINE('',#5096,#5095); -#5098=DIRECTION('',(9.151046470615E-1,0.E0,-4.032164244255E-1)); -#5099=VECTOR('',#5098,9.300180914576E-2); -#5100=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.762499856949E0)); -#5101=LINE('',#5100,#5099); -#5102=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#5103=VECTOR('',#5102,8.507822411232E-2); -#5104=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.725E0)); -#5105=LINE('',#5104,#5103); -#5106=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#5107=VECTOR('',#5106,1.134163884024E-1); -#5108=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.66875E0)); -#5109=LINE('',#5108,#5107); -#5110=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#5111=VECTOR('',#5110,1.144942946081E-1); -#5112=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.575000143051E0)); -#5113=LINE('',#5112,#5111); -#5114=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#5115=VECTOR('',#5114,1.144942946081E-1); -#5116=CARTESIAN_POINT('',(5.75E0,1.55E0,5.462500143051E0)); -#5117=LINE('',#5116,#5115); -#5118=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#5119=VECTOR('',#5118,1.134167431404E-1); -#5120=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.350000143051E0)); -#5121=LINE('',#5120,#5119); -#5122=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#5123=VECTOR('',#5122,8.507822411232E-2); -#5124=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.256249856949E0)); -#5125=LINE('',#5124,#5123); -#5126=DIRECTION('',(-9.151046470615E-1,0.E0,-4.032164244255E-1)); -#5127=VECTOR('',#5126,9.300180914576E-2); -#5128=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.199999856949E0)); -#5129=LINE('',#5128,#5127); -#5130=DIRECTION('',(-9.594603438319E-1,0.E0,-2.818436598788E-1)); -#5131=VECTOR('',#5130,6.652675124645E-2); -#5132=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.1625E0)); -#5133=LINE('',#5132,#5131); -#5134=DIRECTION('',(-9.848211724293E-1,0.E0,-1.735720551671E-1)); -#5135=VECTOR('',#5134,1.080226530685E-1); -#5136=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.143749856949E0)); -#5137=LINE('',#5136,#5135); -#5138=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5139=VECTOR('',#5138,1.914893388748E-1); -#5140=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.125000143051E0)); -#5141=LINE('',#5140,#5139); -#5142=DIRECTION('',(-9.848211641175E-1,0.E0,1.735721023269E-1)); -#5143=VECTOR('',#5142,1.080226237186E-1); -#5144=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.125000143051E0)); -#5145=LINE('',#5144,#5143); -#5146=DIRECTION('',(-9.594604150024E-1,0.E0,2.818434175982E-1)); -#5147=VECTOR('',#5146,6.652680843474E-2); -#5148=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.143749856949E0)); -#5149=LINE('',#5148,#5147); -#5150=DIRECTION('',(-9.151046210116E-1,0.E0,4.032164835459E-1)); -#5151=VECTOR('',#5150,9.300179550964E-2); -#5152=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.1625E0)); -#5153=LINE('',#5152,#5151); -#5154=DIRECTION('',(-7.502481919979E-1,0.E0,6.611562980142E-1)); -#5155=VECTOR('',#5154,8.507821852254E-2); -#5156=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.199999856949E0)); -#5157=LINE('',#5156,#5155); -#5158=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#5159=VECTOR('',#5158,1.134167399956E-1); -#5160=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.256249856949E0)); -#5161=LINE('',#5160,#5159); -#5162=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#5163=VECTOR('',#5162,1.144942942620E-1); -#5164=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.350000143051E0)); -#5165=LINE('',#5164,#5163); -#5166=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#5167=VECTOR('',#5166,1.144942942620E-1); -#5168=CARTESIAN_POINT('',(4.75E0,1.55E0,5.462500143051E0)); -#5169=LINE('',#5168,#5167); -#5170=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#5171=VECTOR('',#5170,1.134163852576E-1); -#5172=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.575000143051E0)); -#5173=LINE('',#5172,#5171); -#5174=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#5175=VECTOR('',#5174,8.507821852253E-2); -#5176=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.66875E0)); -#5177=LINE('',#5176,#5175); -#5178=DIRECTION('',(9.151046210117E-1,0.E0,4.032164835459E-1)); -#5179=VECTOR('',#5178,9.300179550964E-2); -#5180=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.725E0)); -#5181=LINE('',#5180,#5179); -#5182=DIRECTION('',(9.594604150024E-1,0.E0,2.818434175982E-1)); -#5183=VECTOR('',#5182,6.652680843474E-2); -#5184=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.762499856949E0)); -#5185=LINE('',#5184,#5183); -#5186=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554438E-1)); -#5187=VECTOR('',#5186,1.080226982085E-1); -#5188=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.78125E0)); -#5189=LINE('',#5188,#5187); -#5190=DIRECTION('',(-9.893856154061E-1,0.E0,-1.453138122392E-1)); -#5191=VECTOR('',#5190,1.290291239958E-1); -#5192=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.706249856949E0)); -#5193=LINE('',#5192,#5191); -#5194=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#5195=VECTOR('',#5194,1.480607974576E-1); -#5196=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.687500143051E0)); -#5197=LINE('',#5196,#5195); -#5198=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#5199=VECTOR('',#5198,7.053251855852E-2); -#5200=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.6125E0)); -#5201=LINE('',#5200,#5199); -#5202=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#5203=VECTOR('',#5202,9.613391231237E-2); -#5204=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.55625E0)); -#5205=LINE('',#5204,#5203); -#5206=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#5207=VECTOR('',#5206,9.613433082315E-2); -#5208=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,5.462500143051E0)); -#5209=LINE('',#5208,#5207); -#5210=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#5211=VECTOR('',#5210,7.053251855852E-2); -#5212=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.368749856949E0)); -#5213=LINE('',#5212,#5211); -#5214=DIRECTION('',(8.622120674775E-1,0.E0,-5.065474811863E-1)); -#5215=VECTOR('',#5214,1.480605800705E-1); -#5216=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.312499856949E0)); -#5217=LINE('',#5216,#5215); -#5218=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#5219=VECTOR('',#5218,1.290291863584E-1); -#5220=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.237500143051E0)); -#5221=LINE('',#5220,#5219); -#5222=DIRECTION('',(1.E0,0.E0,0.E0)); -#5223=VECTOR('',#5222,1.489361524582E-1); -#5224=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.21875E0)); -#5225=LINE('',#5224,#5223); -#5226=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#5227=VECTOR('',#5226,1.290292158444E-1); -#5228=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.21875E0)); -#5229=LINE('',#5228,#5227); -#5230=DIRECTION('',(8.622119900059E-1,0.E0,5.065476130533E-1)); -#5231=VECTOR('',#5230,1.480605415266E-1); -#5232=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.237500143051E0)); -#5233=LINE('',#5232,#5231); -#5234=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#5235=VECTOR('',#5234,7.053251855852E-2); -#5236=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.312499856949E0)); -#5237=LINE('',#5236,#5235); -#5238=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#5239=VECTOR('',#5238,9.613433082314E-2); -#5240=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.368749856949E0)); -#5241=LINE('',#5240,#5239); -#5242=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#5243=VECTOR('',#5242,9.613391231237E-2); -#5244=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.462500143051E0)); -#5245=LINE('',#5244,#5243); -#5246=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865770E-1)); -#5247=VECTOR('',#5246,7.053251855852E-2); -#5248=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.55625E0)); -#5249=LINE('',#5248,#5247); -#5250=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#5251=VECTOR('',#5250,1.480607589138E-1); -#5252=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.6125E0)); -#5253=LINE('',#5252,#5251); -#5254=DIRECTION('',(-9.893856202834E-1,0.E0,1.453137790318E-1)); -#5255=VECTOR('',#5254,1.290291534818E-1); -#5256=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.687500143051E0)); -#5257=LINE('',#5256,#5255); -#5258=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5259=VECTOR('',#5258,1.489361524582E-1); -#5260=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.706249856949E0)); -#5261=LINE('',#5260,#5259); -#5262=DIRECTION('',(0.E0,0.E0,1.E0)); -#5263=VECTOR('',#5262,1.500002861023E-1); -#5264=CARTESIAN_POINT('',(4.75E0,1.55E0,4.524999856949E0)); -#5265=LINE('',#5264,#5263); -#5266=DIRECTION('',(9.578263606440E-1,0.E0,2.873476341569E-1)); -#5267=VECTOR('',#5266,1.044030568680E0); -#5268=CARTESIAN_POINT('',(4.75E0,1.55E0,4.675000143051E0)); -#5269=LINE('',#5268,#5267); -#5270=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5271=VECTOR('',#5270,1.125E-1); -#5272=CARTESIAN_POINT('',(5.75E0,1.55E0,4.974999856949E0)); -#5273=LINE('',#5272,#5271); -#5274=DIRECTION('',(-9.594612249353E-1,0.E0,-2.818406603838E-1)); -#5275=VECTOR('',#5274,2.661067916729E-1); -#5276=CARTESIAN_POINT('',(5.75E0,1.55E0,4.862499856949E0)); -#5277=LINE('',#5276,#5275); -#5278=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5279=VECTOR('',#5278,3.750002861023E-1); -#5280=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.787500143051E0)); -#5281=LINE('',#5280,#5279); -#5282=DIRECTION('',(9.594612249353E-1,0.E0,-2.818406603838E-1)); -#5283=VECTOR('',#5282,2.661067916729E-1); -#5284=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.412499856949E0)); -#5285=LINE('',#5284,#5283); -#5286=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5287=VECTOR('',#5286,1.125E-1); -#5288=CARTESIAN_POINT('',(5.75E0,1.55E0,4.337500143051E0)); -#5289=LINE('',#5288,#5287); -#5290=DIRECTION('',(-9.578263606440E-1,0.E0,2.873476341569E-1)); -#5291=VECTOR('',#5290,1.044030568680E0); -#5292=CARTESIAN_POINT('',(5.75E0,1.55E0,4.225000143051E0)); -#5293=LINE('',#5292,#5291); -#5294=DIRECTION('',(9.594609371659E-1,0.E0,-2.818416400264E-1)); -#5295=VECTOR('',#5294,5.987404841393E-1); -#5296=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,4.6E0)); -#5297=LINE('',#5296,#5295); -#5298=DIRECTION('',(0.E0,0.E0,1.E0)); -#5299=VECTOR('',#5298,3.375E-1); -#5300=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.43125E0)); -#5301=LINE('',#5300,#5299); -#5302=DIRECTION('',(-9.594609371659E-1,0.E0,-2.818416400264E-1)); -#5303=VECTOR('',#5302,5.987404841393E-1); -#5304=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.76875E0)); -#5305=LINE('',#5304,#5303); -#5306=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5307=VECTOR('',#5306,1.063829958439E-1); -#5308=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,3.8125E0)); -#5309=LINE('',#5308,#5307); -#5310=DIRECTION('',(0.E0,0.E0,1.E0)); -#5311=VECTOR('',#5310,2.624998569489E-1); -#5312=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,3.8125E0)); -#5313=LINE('',#5312,#5311); -#5314=DIRECTION('',(1.E0,0.E0,0.E0)); -#5315=VECTOR('',#5314,1.063829958439E-1); -#5316=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,4.074999856949E0)); -#5317=LINE('',#5316,#5315); -#5318=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5319=VECTOR('',#5318,2.624998569489E-1); -#5320=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,4.074999856949E0)); -#5321=LINE('',#5320,#5319); -#5322=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#5323=VECTOR('',#5322,4.311571495761E-2); -#5324=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,3.08125E0)); -#5325=LINE('',#5324,#5323); -#5326=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#5327=VECTOR('',#5326,1.020154752811E-1); -#5328=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,3.043749713898E0)); -#5329=LINE('',#5328,#5327); -#5330=DIRECTION('',(-9.594620882388E-1,0.E0,-2.818377214504E-1)); -#5331=VECTOR('',#5330,6.652663029355E-2); -#5332=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,2.987499713898E0)); -#5333=LINE('',#5332,#5331); -#5334=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5335=VECTOR('',#5334,8.510643243790E-2); -#5336=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,2.96875E0)); -#5337=LINE('',#5336,#5335); -#5338=DIRECTION('',(-9.594620882388E-1,0.E0,2.818377214504E-1)); -#5339=VECTOR('',#5338,6.652663029355E-2); -#5340=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.96875E0)); -#5341=LINE('',#5340,#5339); -#5342=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#5343=VECTOR('',#5342,1.020154752811E-1); -#5344=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,2.987499713898E0)); -#5345=LINE('',#5344,#5343); -#5346=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#5347=VECTOR('',#5346,9.848515927785E-2); -#5348=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,3.043749713898E0)); -#5349=LINE('',#5348,#5347); -#5350=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#5351=VECTOR('',#5350,9.613349380169E-2); -#5352=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,3.118750286102E0)); -#5353=LINE('',#5352,#5351); -#5354=DIRECTION('',(0.E0,0.E0,1.E0)); -#5355=VECTOR('',#5354,4.500004291534E-1); -#5356=CARTESIAN_POINT('',(4.75E0,1.55E0,3.212499713898E0)); -#5357=LINE('',#5356,#5355); -#5358=DIRECTION('',(1.E0,0.E0,0.E0)); -#5359=VECTOR('',#5358,1.E0); -#5360=CARTESIAN_POINT('',(4.75E0,1.55E0,3.662500143051E0)); -#5361=LINE('',#5360,#5359); -#5362=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5363=VECTOR('',#5362,4.500004291534E-1); -#5364=CARTESIAN_POINT('',(5.75E0,1.55E0,3.662500143051E0)); -#5365=LINE('',#5364,#5363); -#5366=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#5367=VECTOR('',#5366,9.613349421393E-2); -#5368=CARTESIAN_POINT('',(5.75E0,1.55E0,3.212499713898E0)); -#5369=LINE('',#5368,#5367); -#5370=DIRECTION('',(-6.481157499635E-1,0.E0,-7.615418403799E-1)); -#5371=VECTOR('',#5370,9.848516289948E-2); -#5372=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,3.118750286102E0)); -#5373=LINE('',#5372,#5371); -#5374=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#5375=VECTOR('',#5374,1.020154814968E-1); -#5376=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,3.043749713898E0)); -#5377=LINE('',#5376,#5375); -#5378=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#5379=VECTOR('',#5378,6.652664459064E-2); -#5380=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,2.987499713898E0)); -#5381=LINE('',#5380,#5379); -#5382=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5383=VECTOR('',#5382,1.063829660416E-1); -#5384=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,2.96875E0)); -#5385=LINE('',#5384,#5383); -#5386=DIRECTION('',(-9.594621238227E-1,0.E0,2.818376003121E-1)); -#5387=VECTOR('',#5386,6.652665888774E-2); -#5388=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,2.96875E0)); -#5389=LINE('',#5388,#5387); -#5390=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#5391=VECTOR('',#5390,1.020154752811E-1); -#5392=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,2.987499713898E0)); -#5393=LINE('',#5392,#5391); -#5394=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#5395=VECTOR('',#5394,4.311571495761E-2); -#5396=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,3.043749713898E0)); -#5397=LINE('',#5396,#5395); -#5398=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5399=VECTOR('',#5398,3.562501430511E-1); -#5400=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.550000143051E0)); -#5401=LINE('',#5400,#5399); -#5402=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#5403=VECTOR('',#5402,6.013947055430E-2); -#5404=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.19375E0)); -#5405=LINE('',#5404,#5403); -#5406=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#5407=VECTOR('',#5406,5.671900150710E-2); -#5408=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,3.1375E0)); -#5409=LINE('',#5408,#5407); -#5410=DIRECTION('',(9.594621594064E-1,0.E0,-2.818374791740E-1)); -#5411=VECTOR('',#5410,6.652668748194E-2); -#5412=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,3.099999713898E0)); -#5413=LINE('',#5412,#5411); -#5414=DIRECTION('',(1.E0,0.E0,0.E0)); -#5415=VECTOR('',#5414,4.255318641663E-2); -#5416=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,3.08125E0)); -#5417=LINE('',#5416,#5415); -#5418=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#5419=VECTOR('',#5418,6.652663029355E-2); -#5420=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,3.08125E0)); -#5421=LINE('',#5420,#5419); -#5422=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#5423=VECTOR('',#5422,5.671900150710E-2); -#5424=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,3.099999713898E0)); -#5425=LINE('',#5424,#5423); -#5426=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#5427=VECTOR('',#5426,6.013947055430E-2); -#5428=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,3.1375E0)); -#5429=LINE('',#5428,#5427); -#5430=DIRECTION('',(0.E0,0.E0,1.E0)); -#5431=VECTOR('',#5430,3.562501430511E-1); -#5432=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.19375E0)); -#5433=LINE('',#5432,#5431); -#5434=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5435=VECTOR('',#5434,2.978723645210E-1); -#5436=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.550000143051E0)); -#5437=LINE('',#5436,#5435); -#5438=DIRECTION('',(1.E0,0.E0,0.E0)); -#5439=VECTOR('',#5438,6.382977962494E-2); -#5440=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,3.08125E0)); -#5441=LINE('',#5440,#5439); -#5442=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#5443=VECTOR('',#5442,6.652663029355E-2); -#5444=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,3.08125E0)); -#5445=LINE('',#5444,#5443); -#5446=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#5447=VECTOR('',#5446,5.671901268663E-2); -#5448=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,3.099999713898E0)); -#5449=LINE('',#5448,#5447); -#5450=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#5451=VECTOR('',#5450,6.013947055430E-2); -#5452=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,3.1375E0)); -#5453=LINE('',#5452,#5451); -#5454=DIRECTION('',(0.E0,0.E0,1.E0)); -#5455=VECTOR('',#5454,3.562501430511E-1); -#5456=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.19375E0)); -#5457=LINE('',#5456,#5455); -#5458=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5459=VECTOR('',#5458,3.191489428282E-1); -#5460=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.550000143051E0)); -#5461=LINE('',#5460,#5459); -#5462=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5463=VECTOR('',#5462,3.562501430511E-1); -#5464=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.550000143051E0)); -#5465=LINE('',#5464,#5463); -#5466=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#5467=VECTOR('',#5466,6.013947055430E-2); -#5468=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.19375E0)); -#5469=LINE('',#5468,#5467); -#5470=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#5471=VECTOR('',#5470,5.671900150710E-2); -#5472=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,3.1375E0)); -#5473=LINE('',#5472,#5471); -#5474=DIRECTION('',(9.594621238227E-1,0.E0,-2.818376003121E-1)); -#5475=VECTOR('',#5474,6.652665888774E-2); -#5476=CARTESIAN_POINT('',(5.367021262646E0,1.55E0,3.099999713898E0)); -#5477=LINE('',#5476,#5475); -#5478=DIRECTION('',(0.E0,0.E0,1.E0)); -#5479=VECTOR('',#5478,7.124994277954E-1); -#5480=CARTESIAN_POINT('',(4.75E0,1.55E0,2.106250286102E0)); -#5481=LINE('',#5480,#5479); -#5482=DIRECTION('',(1.E0,0.E0,0.E0)); -#5483=VECTOR('',#5482,1.063829660416E-1); -#5484=CARTESIAN_POINT('',(4.75E0,1.55E0,2.818749713898E0)); -#5485=LINE('',#5484,#5483); -#5486=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5487=VECTOR('',#5486,2.999997138977E-1); -#5488=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.818749713898E0)); -#5489=LINE('',#5488,#5487); -#5490=DIRECTION('',(1.E0,0.E0,0.E0)); -#5491=VECTOR('',#5490,8.936170339584E-1); -#5492=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.51875E0)); -#5493=LINE('',#5492,#5491); -#5494=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5495=VECTOR('',#5494,1.125E-1); -#5496=CARTESIAN_POINT('',(5.75E0,1.55E0,2.51875E0)); -#5497=LINE('',#5496,#5495); -#5498=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5499=VECTOR('',#5498,8.936170339584E-1); -#5500=CARTESIAN_POINT('',(5.75E0,1.55E0,2.40625E0)); -#5501=LINE('',#5500,#5499); -#5502=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5503=VECTOR('',#5502,2.999997138977E-1); -#5504=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.40625E0)); -#5505=LINE('',#5504,#5503); -#5506=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5507=VECTOR('',#5506,1.063829660416E-1); -#5508=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.106250286102E0)); -#5509=LINE('',#5508,#5507); -#5510=DIRECTION('',(4.934765254208E-1,0.E0,8.697591154214E-1)); -#5511=VECTOR('',#5510,4.311571495761E-2); -#5512=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.806249713898E0)); -#5513=LINE('',#5512,#5511); -#5514=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#5515=VECTOR('',#5514,9.848450564280E-2); -#5516=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.84375E0)); -#5517=LINE('',#5516,#5515); -#5518=DIRECTION('',(9.431200684716E-1,0.E0,3.324523070247E-1)); -#5519=VECTOR('',#5518,1.127989949533E-1); -#5520=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.918749713898E0)); -#5521=LINE('',#5520,#5519); -#5522=DIRECTION('',(1.E0,0.E0,0.E0)); -#5523=VECTOR('',#5522,6.382977962494E-2); -#5524=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.95625E0)); -#5525=LINE('',#5524,#5523); -#5526=DIRECTION('',(9.431200538709E-1,0.E0,-3.324523484448E-1)); -#5527=VECTOR('',#5526,1.127989808997E-1); -#5528=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.95625E0)); -#5529=LINE('',#5528,#5527); -#5530=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#5531=VECTOR('',#5530,8.507822411232E-2); -#5532=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.918749713898E0)); -#5533=LINE('',#5532,#5531); -#5534=DIRECTION('',(5.627933119354E-1,0.E0,-8.265976578970E-1)); -#5535=VECTOR('',#5534,1.134160336649E-1); -#5536=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.862499713898E0)); -#5537=LINE('',#5536,#5535); -#5538=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#5539=VECTOR('',#5538,9.613433123539E-2); -#5540=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.768750286102E0)); -#5541=LINE('',#5540,#5539); -#5542=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5543=VECTOR('',#5542,1.125E-1); -#5544=CARTESIAN_POINT('',(5.75E0,1.55E0,1.675E0)); -#5545=LINE('',#5544,#5543); -#5546=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#5547=VECTOR('',#5546,9.613433123539E-2); -#5548=CARTESIAN_POINT('',(5.75E0,1.55E0,1.5625E0)); -#5549=LINE('',#5548,#5547); -#5550=DIRECTION('',(-5.627933119354E-1,0.E0,-8.265976578970E-1)); -#5551=VECTOR('',#5550,1.134160336649E-1); -#5552=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.468749713898E0)); -#5553=LINE('',#5552,#5551); -#5554=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#5555=VECTOR('',#5554,8.507822411232E-2); -#5556=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.375000286102E0)); -#5557=LINE('',#5556,#5555); -#5558=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#5559=VECTOR('',#5558,1.127989808997E-1); -#5560=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.318750286102E0)); -#5561=LINE('',#5560,#5559); -#5562=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5563=VECTOR('',#5562,6.382977962494E-2); -#5564=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.28125E0)); -#5565=LINE('',#5564,#5563); -#5566=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#5567=VECTOR('',#5566,1.127989949533E-1); -#5568=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.28125E0)); -#5569=LINE('',#5568,#5567); -#5570=DIRECTION('',(-6.481200185585E-1,0.E0,7.615382075403E-1)); -#5571=VECTOR('',#5570,9.848450564280E-2); -#5572=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.318750286102E0)); -#5573=LINE('',#5572,#5571); -#5574=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#5575=VECTOR('',#5574,4.311571495761E-2); -#5576=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.39375E0)); -#5577=LINE('',#5576,#5575); -#5578=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#5579=VECTOR('',#5578,4.311571495761E-2); -#5580=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.431250286102E0)); -#5581=LINE('',#5580,#5579); -#5582=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#5583=VECTOR('',#5582,8.507821852253E-2); -#5584=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.39375E0)); -#5585=LINE('',#5584,#5583); -#5586=DIRECTION('',(-9.151029183374E-1,0.E0,-4.032203477633E-1)); -#5587=VECTOR('',#5586,9.300196855221E-2); -#5588=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.3375E0)); -#5589=LINE('',#5588,#5587); -#5590=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5591=VECTOR('',#5590,6.382977962494E-2); -#5592=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.299999713898E0)); -#5593=LINE('',#5592,#5591); -#5594=DIRECTION('',(-9.431200976730E-1,0.E0,3.324522241845E-1)); -#5595=VECTOR('',#5594,1.127990230605E-1); -#5596=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.299999713898E0)); -#5597=LINE('',#5596,#5595); -#5598=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#5599=VECTOR('',#5598,8.507821852254E-2); -#5600=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.3375E0)); -#5601=LINE('',#5600,#5599); -#5602=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#5603=VECTOR('',#5602,1.134167399956E-1); -#5604=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.39375E0)); -#5605=LINE('',#5604,#5603); -#5606=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#5607=VECTOR('',#5606,9.613349380168E-2); -#5608=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.487500286102E0)); -#5609=LINE('',#5608,#5607); -#5610=DIRECTION('',(0.E0,0.E0,1.E0)); -#5611=VECTOR('',#5610,7.500057220459E-2); -#5612=CARTESIAN_POINT('',(4.75E0,1.55E0,1.581249713898E0)); -#5613=LINE('',#5612,#5611); -#5614=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#5615=VECTOR('',#5614,9.613349380169E-2); -#5616=CARTESIAN_POINT('',(4.75E0,1.55E0,1.656250286102E0)); -#5617=LINE('',#5616,#5615); -#5618=DIRECTION('',(5.627897577325E-1,0.E0,8.266000777833E-1)); -#5619=VECTOR('',#5618,1.134167399956E-1); -#5620=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.749999713898E0)); -#5621=LINE('',#5620,#5619); -#5622=DIRECTION('',(7.502481919979E-1,0.E0,6.611562980142E-1)); -#5623=VECTOR('',#5622,8.507821852254E-2); -#5624=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.84375E0)); -#5625=LINE('',#5624,#5623); -#5626=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#5627=VECTOR('',#5626,1.127990230605E-1); -#5628=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.9E0)); -#5629=LINE('',#5628,#5627); -#5630=DIRECTION('',(1.E0,0.E0,0.E0)); -#5631=VECTOR('',#5630,6.382977962494E-2); -#5632=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.937500286102E0)); -#5633=LINE('',#5632,#5631); -#5634=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#5635=VECTOR('',#5634,9.300196855221E-2); -#5636=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.937500286102E0)); -#5637=LINE('',#5636,#5635); -#5638=DIRECTION('',(7.502481919979E-1,0.E0,-6.611562980142E-1)); -#5639=VECTOR('',#5638,8.507821852254E-2); -#5640=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.9E0)); -#5641=LINE('',#5640,#5639); -#5642=DIRECTION('',(4.934765254207E-1,0.E0,-8.697591154214E-1)); -#5643=VECTOR('',#5642,4.311571495761E-2); -#5644=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.84375E0)); -#5645=LINE('',#5644,#5643); -#5646=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#5647=VECTOR('',#5646,7.795928747295E-2); -#5648=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.656250286102E0)); -#5649=LINE('',#5648,#5647); -#5650=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#5651=VECTOR('',#5650,8.623068339603E-2); -#5652=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.73125E0)); -#5653=LINE('',#5652,#5651); -#5654=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654784E-1)); -#5655=VECTOR('',#5654,1.020154877124E-1); -#5656=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.806249713898E0)); -#5657=LINE('',#5656,#5655); -#5658=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5659=VECTOR('',#5658,6.382977962494E-2); -#5660=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.862499713898E0)); -#5661=LINE('',#5660,#5659); -#5662=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#5663=VECTOR('',#5662,1.020155001437E-1); -#5664=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.862499713898E0)); -#5665=LINE('',#5664,#5663); -#5666=DIRECTION('',(-4.934807975624E-1,0.E0,-8.697566915162E-1)); -#5667=VECTOR('',#5666,8.623068339603E-2); -#5668=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.806249713898E0)); -#5669=LINE('',#5668,#5667); -#5670=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#5671=VECTOR('',#5670,7.795928747295E-2); -#5672=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.73125E0)); -#5673=LINE('',#5672,#5671); -#5674=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5675=VECTOR('',#5674,7.500057220459E-2); -#5676=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.656250286102E0)); -#5677=LINE('',#5676,#5675); -#5678=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#5679=VECTOR('',#5678,7.795928747295E-2); -#5680=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.581249713898E0)); -#5681=LINE('',#5680,#5679); -#5682=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#5683=VECTOR('',#5682,8.623068339603E-2); -#5684=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.50625E0)); -#5685=LINE('',#5684,#5683); -#5686=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#5687=VECTOR('',#5686,1.020155001437E-1); -#5688=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.431250286102E0)); -#5689=LINE('',#5688,#5687); -#5690=DIRECTION('',(1.E0,0.E0,0.E0)); -#5691=VECTOR('',#5690,6.382977962494E-2); -#5692=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.375000286102E0)); -#5693=LINE('',#5692,#5691); -#5694=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#5695=VECTOR('',#5694,1.020154877124E-1); -#5696=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.375000286102E0)); -#5697=LINE('',#5696,#5695); -#5698=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#5699=VECTOR('',#5698,8.623068339603E-2); -#5700=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.431250286102E0)); -#5701=LINE('',#5700,#5699); -#5702=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#5703=VECTOR('',#5702,7.795928747295E-2); -#5704=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.50625E0)); -#5705=LINE('',#5704,#5703); -#5706=DIRECTION('',(0.E0,0.E0,1.E0)); -#5707=VECTOR('',#5706,7.500057220459E-2); -#5708=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.581249713898E0)); -#5709=LINE('',#5708,#5707); -#5710=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#5711=VECTOR('',#5710,7.795928747295E-2); -#5712=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.581249713898E0)); -#5713=LINE('',#5712,#5711); -#5714=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#5715=VECTOR('',#5714,9.848450564280E-2); -#5716=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.50625E0)); -#5717=LINE('',#5716,#5715); -#5718=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#5719=VECTOR('',#5718,7.403053311863E-2); -#5720=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.431250286102E0)); -#5721=LINE('',#5720,#5719); -#5722=DIRECTION('',(1.E0,0.E0,0.E0)); -#5723=VECTOR('',#5722,4.255318641663E-2); -#5724=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.39375E0)); -#5725=LINE('',#5724,#5723); -#5726=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#5727=VECTOR('',#5726,7.403048172694E-2); -#5728=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.39375E0)); -#5729=LINE('',#5728,#5727); -#5730=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#5731=VECTOR('',#5730,9.848450564280E-2); -#5732=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.431250286102E0)); -#5733=LINE('',#5732,#5731); -#5734=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#5735=VECTOR('',#5734,7.795928747295E-2); -#5736=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.50625E0)); -#5737=LINE('',#5736,#5735); -#5738=DIRECTION('',(0.E0,0.E0,1.E0)); -#5739=VECTOR('',#5738,7.500057220459E-2); -#5740=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.581249713898E0)); -#5741=LINE('',#5740,#5739); -#5742=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#5743=VECTOR('',#5742,7.795928747295E-2); -#5744=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.656250286102E0)); -#5745=LINE('',#5744,#5743); -#5746=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#5747=VECTOR('',#5746,9.848450564280E-2); -#5748=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.73125E0)); -#5749=LINE('',#5748,#5747); -#5750=DIRECTION('',(-8.622094323306E-1,0.E0,5.065519665347E-1)); -#5751=VECTOR('',#5750,7.403048172694E-2); -#5752=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.806249713898E0)); -#5753=LINE('',#5752,#5751); -#5754=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5755=VECTOR('',#5754,4.255318641663E-2); -#5756=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.84375E0)); -#5757=LINE('',#5756,#5755); -#5758=DIRECTION('',(-8.622096389243E-1,0.E0,-5.065516148884E-1)); -#5759=VECTOR('',#5758,7.403053311863E-2); -#5760=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.84375E0)); -#5761=LINE('',#5760,#5759); -#5762=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#5763=VECTOR('',#5762,9.848450564280E-2); -#5764=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.806249713898E0)); -#5765=LINE('',#5764,#5763); -#5766=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#5767=VECTOR('',#5766,7.795928747295E-2); -#5768=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.73125E0)); -#5769=LINE('',#5768,#5767); -#5770=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5771=VECTOR('',#5770,7.500057220459E-2); -#5772=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.656250286102E0)); -#5773=LINE('',#5772,#5771); -#5774=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#5775=VECTOR('',#5774,7.403004695359E-2); -#5776=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.124997138977E-1)); -#5777=LINE('',#5776,#5775); -#5778=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#5779=VECTOR('',#5778,6.652688649895E-2); -#5780=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,4.750002861023E-1)); -#5781=LINE('',#5780,#5779); -#5782=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5783=VECTOR('',#5782,8.510637283325E-2); -#5784=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,4.562497138977E-1)); -#5785=LINE('',#5784,#5783); -#5786=DIRECTION('',(-9.765790138025E-1,0.E0,2.151590802187E-1)); -#5787=VECTOR('',#5786,8.714748262324E-2); -#5788=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,4.562497138977E-1)); -#5789=LINE('',#5788,#5787); -#5790=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#5791=VECTOR('',#5790,7.403004695359E-2); -#5792=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,4.750002861023E-1)); -#5793=LINE('',#5792,#5791); -#5794=DIRECTION('',(-4.133152317521E-1,0.E0,9.105880073896E-1)); -#5795=VECTOR('',#5794,1.029557663197E-1); -#5796=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,5.124997138977E-1)); -#5797=LINE('',#5796,#5795); -#5798=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#5799=VECTOR('',#5798,9.848450564280E-2); -#5800=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,6.0625E-1)); -#5801=LINE('',#5800,#5799); -#5802=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#5803=VECTOR('',#5802,7.403048172694E-2); -#5804=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.312502861023E-1)); -#5805=LINE('',#5804,#5803); -#5806=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#5807=VECTOR('',#5806,8.714726885037E-2); -#5808=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,4.9375E-1)); -#5809=LINE('',#5808,#5807); -#5810=DIRECTION('',(-1.E0,0.E0,0.E0)); -#5811=VECTOR('',#5810,4.255324602127E-2); -#5812=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,4.750002861023E-1)); -#5813=LINE('',#5812,#5811); -#5814=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#5815=VECTOR('',#5814,8.714726885037E-2); -#5816=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,4.750002861023E-1)); -#5817=LINE('',#5816,#5815); -#5818=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#5819=VECTOR('',#5818,1.134374355386E-1); -#5820=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,4.9375E-1)); -#5821=LINE('',#5820,#5819); -#5822=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#5823=VECTOR('',#5822,8.623142991522E-2); -#5824=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,5.687497138977E-1)); -#5825=LINE('',#5824,#5823); -#5826=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#5827=VECTOR('',#5826,1.329630806532E-1); -#5828=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.437502861023E-1)); -#5829=LINE('',#5828,#5827); -#5830=DIRECTION('',(0.E0,0.E0,1.E0)); -#5831=VECTOR('',#5830,3.750028610230E-2); -#5832=CARTESIAN_POINT('',(4.75E0,1.55E0,7.75E-1)); -#5833=LINE('',#5832,#5831); -#5834=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#5835=VECTOR('',#5834,1.329630806532E-1); -#5836=CARTESIAN_POINT('',(4.75E0,1.55E0,8.125002861023E-1)); -#5837=LINE('',#5836,#5835); -#5838=DIRECTION('',(4.934807975625E-1,0.E0,8.697566915162E-1)); -#5839=VECTOR('',#5838,8.623068339603E-2); -#5840=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.4375E-1)); -#5841=LINE('',#5840,#5839); -#5842=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#5843=VECTOR('',#5842,1.134380030142E-1); -#5844=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.018749713898E0)); -#5845=LINE('',#5844,#5843); -#5846=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#5847=VECTOR('',#5846,8.714726885037E-2); -#5848=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.093750286102E0)); -#5849=LINE('',#5848,#5847); -#5850=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5851=VECTOR('',#5850,9.375028610230E-2); -#5852=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.1125E0)); -#5853=LINE('',#5852,#5851); -#5854=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#5855=VECTOR('',#5854,7.403004695359E-2); -#5856=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.018749713898E0)); -#5857=LINE('',#5856,#5855); -#5858=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#5859=VECTOR('',#5858,7.053251855852E-2); -#5860=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,9.812502861023E-1)); -#5861=LINE('',#5860,#5859); -#5862=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#5863=VECTOR('',#5862,9.613433082315E-2); -#5864=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.250002861023E-1)); -#5865=LINE('',#5864,#5863); -#5866=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5867=VECTOR('',#5866,7.499971389771E-2); -#5868=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,8.3125E-1)); -#5869=LINE('',#5868,#5867); -#5870=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#5871=VECTOR('',#5870,9.613433082315E-2); -#5872=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,7.562502861023E-1)); -#5873=LINE('',#5872,#5871); -#5874=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#5875=VECTOR('',#5874,7.053251855852E-2); -#5876=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.625E-1)); -#5877=LINE('',#5876,#5875); -#5878=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#5879=VECTOR('',#5878,7.403048172694E-2); -#5880=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.0625E-1)); -#5881=LINE('',#5880,#5879); -#5882=DIRECTION('',(1.E0,0.E0,0.E0)); -#5883=VECTOR('',#5882,4.255324602127E-2); -#5884=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.687497138977E-1)); -#5885=LINE('',#5884,#5883); -#5886=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#5887=VECTOR('',#5886,9.300196855221E-2); -#5888=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,5.687497138977E-1)); -#5889=LINE('',#5888,#5887); -#5890=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#5891=VECTOR('',#5890,5.671900150710E-2); -#5892=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,6.0625E-1)); -#5893=LINE('',#5892,#5891); -#5894=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#5895=VECTOR('',#5894,1.202789411086E-1); -#5896=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.437502861023E-1)); -#5897=LINE('',#5896,#5895); -#5898=DIRECTION('',(0.E0,0.E0,1.E0)); -#5899=VECTOR('',#5898,7.499971389771E-2); -#5900=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,7.562502861023E-1)); -#5901=LINE('',#5900,#5899); -#5902=DIRECTION('',(1.E0,0.E0,0.E0)); -#5903=VECTOR('',#5902,8.510637283325E-2); -#5904=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,8.3125E-1)); -#5905=LINE('',#5904,#5903); -#5906=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5907=VECTOR('',#5906,7.499971389771E-2); -#5908=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,8.3125E-1)); -#5909=LINE('',#5908,#5907); -#5910=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#5911=VECTOR('',#5910,1.144942942620E-1); -#5912=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,7.562502861023E-1)); -#5913=LINE('',#5912,#5911); -#5914=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#5915=VECTOR('',#5914,7.053251855852E-2); -#5916=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,6.437502861023E-1)); -#5917=LINE('',#5916,#5915); -#5918=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#5919=VECTOR('',#5918,9.300199582440E-2); -#5920=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.875002861023E-1)); -#5921=LINE('',#5920,#5919); -#5922=DIRECTION('',(1.E0,0.E0,0.E0)); -#5923=VECTOR('',#5922,8.510637283325E-2); -#5924=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,5.5E-1)); -#5925=LINE('',#5924,#5923); -#5926=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#5927=VECTOR('',#5926,4.650081123436E-2); -#5928=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.5E-1)); -#5929=LINE('',#5928,#5927); -#5930=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#5931=VECTOR('',#5930,5.671901268663E-2); -#5932=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,5.687497138977E-1)); -#5933=LINE('',#5932,#5931); -#5934=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#5935=VECTOR('',#5934,4.311571495761E-2); -#5936=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.0625E-1)); -#5937=LINE('',#5936,#5935); -#5938=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#5939=VECTOR('',#5938,9.613349380168E-2); -#5940=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.437502861023E-1)); -#5941=LINE('',#5940,#5939); -#5942=DIRECTION('',(0.E0,0.E0,1.E0)); -#5943=VECTOR('',#5942,1.125E-1); -#5944=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,7.374997138977E-1)); -#5945=LINE('',#5944,#5943); -#5946=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#5947=VECTOR('',#5946,9.613433082315E-2); -#5948=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.499997138977E-1)); -#5949=LINE('',#5948,#5947); -#5950=DIRECTION('',(-4.934765254208E-1,0.E0,8.697591154214E-1)); -#5951=VECTOR('',#5950,4.311571495761E-2); -#5952=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.4375E-1)); -#5953=LINE('',#5952,#5951); -#5954=DIRECTION('',(-7.502533110351E-1,0.E0,6.611504891330E-1)); -#5955=VECTOR('',#5954,5.671844521296E-2); -#5956=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.812502861023E-1)); -#5957=LINE('',#5956,#5955); -#5958=DIRECTION('',(-9.150995129590E-1,0.E0,4.032280761334E-1)); -#5959=VECTOR('',#5958,4.650115732116E-2); -#5960=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.018749713898E0)); -#5961=LINE('',#5960,#5959); -#5962=DIRECTION('',(0.E0,0.E0,1.E0)); -#5963=VECTOR('',#5962,9.374942779541E-2); -#5964=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.037500286102E0)); -#5965=LINE('',#5964,#5963); -#5966=DIRECTION('',(9.594621060308E-1,0.E0,-2.818376608812E-1)); -#5967=VECTOR('',#5966,6.652664459064E-2); -#5968=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.131249713898E0)); -#5969=LINE('',#5968,#5967); -#5970=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#5971=VECTOR('',#5970,7.403048172694E-2); -#5972=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.1125E0)); -#5973=LINE('',#5972,#5971); -#5974=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#5975=VECTOR('',#5974,7.053252305355E-2); -#5976=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.074999713898E0)); -#5977=LINE('',#5976,#5975); -#5978=DIRECTION('',(4.934808465838E-1,0.E0,-8.697566637025E-1)); -#5979=VECTOR('',#5978,8.623068615356E-2); -#5980=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.018749713898E0)); -#5981=LINE('',#5980,#5979); -#5982=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#5983=VECTOR('',#5982,7.795928798130E-2); -#5984=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.4375E-1)); -#5985=LINE('',#5984,#5983); -#5986=DIRECTION('',(0.E0,0.E0,-1.E0)); -#5987=VECTOR('',#5986,1.500002861023E-1); -#5988=CARTESIAN_POINT('',(5.75E0,1.55E0,8.687502861023E-1)); -#5989=LINE('',#5988,#5987); -#5990=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#5991=VECTOR('',#5990,7.795928798130E-2); -#5992=CARTESIAN_POINT('',(5.75E0,1.55E0,7.1875E-1)); -#5993=LINE('',#5992,#5991); -#5994=DIRECTION('',(-4.934765744419E-1,0.E0,-8.697590876082E-1)); -#5995=VECTOR('',#5994,8.623143267274E-2); -#5996=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.437502861023E-1)); -#5997=LINE('',#5996,#5995); -#5998=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#5999=VECTOR('',#5998,7.053252305355E-2); -#6000=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,5.687497138977E-1)); -#6001=LINE('',#6000,#5999); -#6002=DIRECTION('',(1.E0,0.E0,0.E0)); -#6003=VECTOR('',#6002,1.063829809427E-1); -#6004=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,3.062502861023E-1)); -#6005=LINE('',#6004,#6003); -#6006=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6007=VECTOR('',#6006,6.75E-1); -#6008=CARTESIAN_POINT('',(5.75E0,1.55E0,3.062502861023E-1)); -#6009=LINE('',#6008,#6007); -#6010=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6011=VECTOR('',#6010,1.063829809427E-1); -#6012=CARTESIAN_POINT('',(5.75E0,1.55E0,-3.687497138977E-1)); -#6013=LINE('',#6012,#6011); -#6014=DIRECTION('',(0.E0,0.E0,1.E0)); -#6015=VECTOR('',#6014,5.249997138977E-1); -#6016=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,-3.687497138977E-1)); -#6017=LINE('',#6016,#6015); -#6018=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#6019=VECTOR('',#6018,6.624424131262E-1); -#6020=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.5625E-1)); -#6021=LINE('',#6020,#6019); -#6022=DIRECTION('',(-8.622094323306E-1,0.E0,-5.065519665348E-1)); -#6023=VECTOR('',#6022,7.403048172694E-2); -#6024=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,-3.124997138977E-1)); -#6025=LINE('',#6024,#6023); -#6026=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#6027=VECTOR('',#6026,8.714726885037E-2); -#6028=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-3.5E-1)); -#6029=LINE('',#6028,#6027); -#6030=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6031=VECTOR('',#6030,4.255324602127E-2); -#6032=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-3.687497138977E-1)); -#6033=LINE('',#6032,#6031); -#6034=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#6035=VECTOR('',#6034,8.714726885037E-2); -#6036=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-3.687497138977E-1)); -#6037=LINE('',#6036,#6035); -#6038=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#6039=VECTOR('',#6038,1.134374355386E-1); -#6040=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,-3.5E-1)); -#6041=LINE('',#6040,#6039); -#6042=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#6043=VECTOR('',#6042,8.623142991522E-2); -#6044=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,-2.750002861023E-1)); -#6045=LINE('',#6044,#6043); -#6046=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#6047=VECTOR('',#6046,1.144942942620E-1); -#6048=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,-1.999997138977E-1)); -#6049=LINE('',#6048,#6047); -#6050=DIRECTION('',(0.E0,0.E0,1.E0)); -#6051=VECTOR('',#6050,7.499971389771E-2); -#6052=CARTESIAN_POINT('',(4.75E0,1.55E0,-8.749971389771E-2)); -#6053=LINE('',#6052,#6051); -#6054=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#6055=VECTOR('',#6054,1.329630806532E-1); -#6056=CARTESIAN_POINT('',(4.75E0,1.55E0,-1.25E-2)); -#6057=LINE('',#6056,#6055); -#6058=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#6059=VECTOR('',#6058,8.623142991522E-2); -#6060=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.187497138977E-1)); -#6061=LINE('',#6060,#6059); -#6062=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#6063=VECTOR('',#6062,1.134374355386E-1); -#6064=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.937502861023E-1)); -#6065=LINE('',#6064,#6063); -#6066=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#6067=VECTOR('',#6066,8.714726885037E-2); -#6068=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,2.6875E-1)); -#6069=LINE('',#6068,#6067); -#6070=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6071=VECTOR('',#6070,9.374942779541E-2); -#6072=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.874997138977E-1)); -#6073=LINE('',#6072,#6071); -#6074=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#6075=VECTOR('',#6074,7.403048172694E-2); -#6076=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.937502861023E-1)); -#6077=LINE('',#6076,#6075); -#6078=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#6079=VECTOR('',#6078,7.053251855852E-2); -#6080=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,1.5625E-1)); -#6081=LINE('',#6080,#6079); -#6082=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#6083=VECTOR('',#6082,9.613433082315E-2); -#6084=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.E-1)); -#6085=LINE('',#6084,#6083); -#6086=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6087=VECTOR('',#6086,7.499971389771E-2); -#6088=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.249713897704E-3)); -#6089=LINE('',#6088,#6087); -#6090=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#6091=VECTOR('',#6090,9.613433082315E-2); -#6092=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,-6.875E-2)); -#6093=LINE('',#6092,#6091); -#6094=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#6095=VECTOR('',#6094,7.053251855852E-2); -#6096=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,-1.625002861023E-1)); -#6097=LINE('',#6096,#6095); -#6098=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#6099=VECTOR('',#6098,7.403004695359E-2); -#6100=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,-2.187502861023E-1)); -#6101=LINE('',#6100,#6099); -#6102=DIRECTION('',(1.E0,0.E0,0.E0)); -#6103=VECTOR('',#6102,4.255324602127E-2); -#6104=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-2.562497138977E-1)); -#6105=LINE('',#6104,#6103); -#6106=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#6107=VECTOR('',#6106,9.300162246873E-2); -#6108=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-2.562497138977E-1)); -#6109=LINE('',#6108,#6107); -#6110=DIRECTION('',(7.117174186007E-1,0.E0,7.024658824885E-1)); -#6111=VECTOR('',#6110,7.473680719479E-1); -#6112=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-2.187502861023E-1)); -#6113=LINE('',#6112,#6111); -#6114=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6115=VECTOR('',#6114,6.607553893797E-1); -#6116=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,7.509479917553E-1)); -#6117=LINE('',#6116,#6115); -#6118=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,9.019260237562E-2)); -#6119=CARTESIAN_POINT('',(-2.322772147471E0,1.55E0,8.938882588201E-2)); -#6120=CARTESIAN_POINT('',(-2.349448326548E0,1.55E0,8.804870970072E-2)); -#6121=CARTESIAN_POINT('',(-2.389501970825E0,1.55E0,8.684238554311E-2)); -#6122=CARTESIAN_POINT('',(-2.416210448397E0,1.55E0,8.657467796390E-2)); -#6123=CARTESIAN_POINT('',(-2.429572153713E0,1.55E0,8.657433522519E-2)); -#6125=CARTESIAN_POINT('',(-2.429572153713E0,1.55E0,8.657433522519E-2)); -#6126=CARTESIAN_POINT('',(-2.546324832949E0,1.55E0,8.770091901078E-2)); -#6127=CARTESIAN_POINT('',(-2.774383252738E0,1.55E0,1.062811465330E-1)); -#6128=CARTESIAN_POINT('',(-3.108900823435E0,1.55E0,1.949327331270E-1)); -#6129=CARTESIAN_POINT('',(-3.316229164484E0,1.55E0,2.917357635001E-1)); -#6130=CARTESIAN_POINT('',(-3.418216415891E0,1.55E0,3.485781583319E-1)); -#6132=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,7.509479917553E-1)); -#6133=CARTESIAN_POINT('',(-2.679028565125E0,1.55E0,6.168247139475E-1)); -#6134=CARTESIAN_POINT('',(-3.048622490508E0,1.55E0,4.827014361397E-1)); -#6135=CARTESIAN_POINT('',(-3.418216415891E0,1.55E0,3.485781583319E-1)); -#6137=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.765777389509E0)); -#6138=CARTESIAN_POINT('',(-1.238595103198E0,1.55E0,3.688808300316E0)); -#6139=CARTESIAN_POINT('',(-1.022070928953E0,1.55E0,3.519467320563E0)); -#6140=CARTESIAN_POINT('',(-7.622795865223E-1,1.55E0,3.204305359310E0)); -#6141=CARTESIAN_POINT('',(-5.737617442267E-1,1.55E0,2.852856095504E0)); -#6142=CARTESIAN_POINT('',(-4.587233502244E-1,1.55E0,2.473154193031E0)); -#6143=CARTESIAN_POINT('',(-4.206251047483E-1,1.55E0,2.080943871044E0)); -#6144=CARTESIAN_POINT('',(-4.594562146907E-1,1.55E0,1.688998689711E0)); -#6145=CARTESIAN_POINT('',(-5.749895968984E-1,1.55E0,1.309952967809E0)); -#6146=CARTESIAN_POINT('',(-7.636677122414E-1,1.55E0,9.594500467100E-1)); -#6147=CARTESIAN_POINT('',(-1.023079524938E0,1.55E0,6.453710459650E-1)); -#6148=CARTESIAN_POINT('',(-1.238984642817E0,1.55E0,4.765898563533E-1)); -#6149=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.999217256483E-1)); -#6151=DIRECTION('',(0.E0,0.E0,1.E0)); -#6152=VECTOR('',#6151,3.365855663861E0); -#6153=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.999217256483E-1)); -#6154=LINE('',#6153,#6152); -#6155=CARTESIAN_POINT('',(-2.705883122562E0,1.55E0,4.059909751877E0)); -#6156=CARTESIAN_POINT('',(-2.732942410469E0,1.55E0,4.071744299724E0)); -#6157=CARTESIAN_POINT('',(-2.786478319988E0,1.55E0,4.111684285312E0)); -#6158=CARTESIAN_POINT('',(-2.842964704605E0,1.55E0,4.194760630358E0)); -#6159=CARTESIAN_POINT('',(-2.884363683665E0,1.55E0,4.287845204590E0)); -#6160=CARTESIAN_POINT('',(-2.914885019781E0,1.55E0,4.375596147512E0)); -#6161=CARTESIAN_POINT('',(-2.940504397788E0,1.55E0,4.455778808010E0)); -#6162=CARTESIAN_POINT('',(-2.963736274210E0,1.55E0,4.525419954314E0)); -#6163=CARTESIAN_POINT('',(-2.990108794848E0,1.55E0,4.586877566231E0)); -#6164=CARTESIAN_POINT('',(-3.022737030265E0,1.55E0,4.636243139881E0)); -#6165=CARTESIAN_POINT('',(-3.065917078232E0,1.55E0,4.670416877497E0)); -#6166=CARTESIAN_POINT('',(-3.116627615079E0,1.55E0,4.679212470761E0)); -#6167=CARTESIAN_POINT('',(-3.164716940033E0,1.55E0,4.662778200878E0)); -#6168=CARTESIAN_POINT('',(-3.207010146779E0,1.55E0,4.629197867869E0)); -#6169=CARTESIAN_POINT('',(-3.240627301698E0,1.55E0,4.585360822888E0)); -#6170=CARTESIAN_POINT('',(-3.263425109942E0,1.55E0,4.536678364466E0)); -#6171=CARTESIAN_POINT('',(-3.272148755802E0,1.55E0,4.489539165406E0)); -#6172=CARTESIAN_POINT('',(-3.263041702391E0,1.55E0,4.445753294666E0)); -#6173=CARTESIAN_POINT('',(-3.233551737216E0,1.55E0,4.418493178925E0)); -#6174=CARTESIAN_POINT('',(-3.196008723068E0,1.55E0,4.409848993101E0)); -#6175=CARTESIAN_POINT('',(-3.170701330978E0,1.55E0,4.410834700981E0)); -#6176=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,4.412619339018E0)); -#6178=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6179=VECTOR('',#6178,4.708180158703E-1); -#6180=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,4.412619339018E0)); -#6181=LINE('',#6180,#6179); -#6182=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.941801323147E0)); -#6183=CARTESIAN_POINT('',(-3.108507370770E0,1.55E0,3.960770940436E0)); -#6184=CARTESIAN_POINT('',(-3.010566019986E0,1.55E0,3.994843097695E0)); -#6185=CARTESIAN_POINT('',(-2.859684165553E0,1.55E0,4.034330233211E0)); -#6186=CARTESIAN_POINT('',(-2.757608330667E0,1.55E0,4.052604368656E0)); -#6187=CARTESIAN_POINT('',(-2.705883122562E0,1.55E0,4.059909751877E0)); -#6189=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.111585449519E0)); -#6190=CARTESIAN_POINT('',(-3.221502667931E0,1.55E0,6.114320057001E0)); -#6191=CARTESIAN_POINT('',(-2.898564208026E0,1.55E0,6.117054664482E0)); -#6192=CARTESIAN_POINT('',(-2.575625748121E0,1.55E0,6.119789271963E0)); -#6194=DIRECTION('',(0.E0,0.E0,1.E0)); -#6195=VECTOR('',#6194,7.867771456628E-1); -#6196=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.111585449519E0)); -#6197=LINE('',#6196,#6195); -#6198=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,7.489725709329E0)); -#6199=CARTESIAN_POINT('',(-2.463642722499E0,1.55E0,7.292604671280E0)); -#6200=CARTESIAN_POINT('',(-3.004041925168E0,1.55E0,7.095483633231E0)); -#6201=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.898362595182E0)); -#6203=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6204=VECTOR('',#6203,5.221379787490E-1); -#6205=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,7.489725709329E0)); -#6206=LINE('',#6205,#6204); -#6207=CARTESIAN_POINT('',(-2.874810490240E0,1.55E0,6.616961294258E0)); -#6208=CARTESIAN_POINT('',(-2.557621500104E0,1.55E0,6.733836773032E0)); -#6209=CARTESIAN_POINT('',(-2.240432509967E0,1.55E0,6.850712251806E0)); -#6210=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,6.967587730580E0)); -#6212=DIRECTION('',(9.999979297889E-1,0.E0,-2.034801677749E-3)); -#6213=VECTOR('',#6212,9.515944181204E-1); -#6214=CARTESIAN_POINT('',(-2.874810490240E0,1.55E0,6.616961294258E0)); -#6215=LINE('',#6214,#6213); -#6216=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6217=VECTOR('',#6216,7.896418426795E-1); -#6218=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,6.615024988339E0)); -#6219=LINE('',#6218,#6217); -#6220=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.239527664520E0)); -#6221=CARTESIAN_POINT('',(-3.004041925168E0,1.55E0,5.434812824900E0)); -#6222=CARTESIAN_POINT('',(-2.463629983644E0,1.55E0,5.630097985280E0)); -#6223=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,5.825383145660E0)); -#6225=DIRECTION('',(0.E0,0.E0,1.E0)); -#6226=VECTOR('',#6225,5.170593332799E-1); -#6227=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.239527664520E0)); -#6228=LINE('',#6227,#6226); -#6229=CARTESIAN_POINT('',(-2.575625748121E0,1.55E0,6.119789271963E0)); -#6230=CARTESIAN_POINT('',(-2.898568454311E0,1.55E0,5.998721847242E0)); -#6231=CARTESIAN_POINT('',(-3.221511160501E0,1.55E0,5.877654422521E0)); -#6232=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.756586997800E0)); -#6234=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.067463319291E0)); -#6235=CARTESIAN_POINT('',(-2.740738290526E0,1.55E0,8.015512579589E0)); -#6236=CARTESIAN_POINT('',(-2.990233006644E0,1.55E0,7.963561839887E0)); -#6237=CARTESIAN_POINT('',(-3.239727722762E0,1.55E0,7.911611100185E0)); -#6239=DIRECTION('',(0.E0,0.E0,1.E0)); -#6240=VECTOR('',#6239,2.451848855720E-1); -#6241=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.067463319291E0)); -#6242=LINE('',#6241,#6240); -#6243=CARTESIAN_POINT('',(-3.239727722762E0,1.55E0,7.911611100185E0)); -#6244=CARTESIAN_POINT('',(-2.990233006644E0,1.55E0,8.045290135078E0)); -#6245=CARTESIAN_POINT('',(-2.740738290526E0,1.55E0,8.178969169970E0)); -#6246=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.312648204863E0)); -#6248=DIRECTION('',(-1.577221316427E-3,0.E0,-9.999987561857E-1)); -#6249=VECTOR('',#6248,6.299881052683E-1); -#6250=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,9.242286387282E0)); -#6251=LINE('',#6250,#6249); -#6252=CARTESIAN_POINT('',(-2.177281760801E0,1.55E0,8.477445549459E0)); -#6253=CARTESIAN_POINT('',(-2.092933557367E0,1.55E0,8.522396721507E0)); -#6254=CARTESIAN_POINT('',(-2.008585353933E0,1.55E0,8.567347893554E0)); -#6255=CARTESIAN_POINT('',(-1.924237150499E0,1.55E0,8.612299065602E0)); -#6257=DIRECTION('',(6.593263280460E-3,0.E0,-9.999782642034E-1)); -#6258=VECTOR('',#6257,3.361856835150E-1); -#6259=CARTESIAN_POINT('',(-2.177281760801E0,1.55E0,8.477445549459E0)); -#6260=LINE('',#6259,#6258); -#6261=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,8.187006604870E0)); -#6262=CARTESIAN_POINT('',(-2.007226542762E0,1.55E0,8.171760127649E0)); -#6263=CARTESIAN_POINT('',(-2.091145871421E0,1.55E0,8.156513650429E0)); -#6264=CARTESIAN_POINT('',(-2.175065200079E0,1.55E0,8.141267173208E0)); -#6266=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6267=VECTOR('',#6266,6.267625716583E-1); -#6268=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,8.187006604870E0)); -#6269=LINE('',#6268,#6267); -#6270=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,7.391589548398E0)); -#6271=CARTESIAN_POINT('',(-3.004054664022E0,1.55E0,7.447807710003E0)); -#6272=CARTESIAN_POINT('',(-2.463680939063E0,1.55E0,7.504025871607E0)); -#6273=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,7.560244033212E0)); -#6275=DIRECTION('',(0.E0,0.E0,1.E0)); -#6276=VECTOR('',#6275,8.351823564918E-1); -#6277=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,7.391589548398E0)); -#6278=LINE('',#6277,#6276); -#6279=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,9.242286387282E0)); -#6280=CARTESIAN_POINT('',(-2.463638476214E0,1.55E0,8.903781559818E0)); -#6281=CARTESIAN_POINT('',(-3.004033432598E0,1.55E0,8.565276732354E0)); -#6282=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,8.226771904890E0)); -#6284=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6285=VECTOR('',#6284,6.119283121188E-1); -#6286=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,1.037838840728E1)); -#6287=LINE('',#6286,#6285); -#6288=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,9.528323510344E0)); -#6289=CARTESIAN_POINT('',(-2.355464368156E0,1.55E0,9.607702371948E0)); -#6290=CARTESIAN_POINT('',(-2.139328466284E0,1.55E0,9.687081233552E0)); -#6291=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,9.766460095156E0)); -#6293=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6294=VECTOR('',#6293,5.877696361310E-1); -#6295=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,9.528323510344E0)); -#6296=LINE('',#6295,#6294); -#6297=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,8.815613659747E0)); -#6298=CARTESIAN_POINT('',(-2.802216003439E0,1.55E0,8.857260397902E0)); -#6299=CARTESIAN_POINT('',(-2.686908136734E0,1.55E0,8.898907136057E0)); -#6300=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,8.940553874213E0)); -#6302=DIRECTION('',(0.E0,0.E0,1.E0)); -#6303=VECTOR('',#6302,5.863925654006E-1); -#6304=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,8.815613659747E0)); -#6305=LINE('',#6304,#6303); -#6306=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,9.305944961207E0)); -#6307=CARTESIAN_POINT('',(-3.077141719877E0,1.55E0,9.337965382520E0)); -#6308=CARTESIAN_POINT('',(-2.997332795011E0,1.55E0,9.369985803834E0)); -#6309=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,9.402006225147E0)); -#6311=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6312=VECTOR('',#6311,6.280568557938E-1); -#6313=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,9.305944961207E0)); -#6314=LINE('',#6313,#6312); -#6315=CARTESIAN_POINT('',(-3.543727751972E0,1.55E0,8.534948739698E0)); -#6316=CARTESIAN_POINT('',(-3.414802049562E0,1.55E0,8.582595194936E0)); -#6317=CARTESIAN_POINT('',(-3.285876347153E0,1.55E0,8.630241650174E0)); -#6318=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,8.677888105413E0)); -#6320=DIRECTION('',(-5.670519560576E-4,0.E0,9.999998392260E-1)); -#6321=VECTOR('',#6320,1.258043212979E0); -#6322=CARTESIAN_POINT('',(-3.543727751972E0,1.55E0,8.534948739698E0)); -#6323=LINE('',#6322,#6321); -#6324=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,1.037838840728E1)); -#6325=CARTESIAN_POINT('',(-2.463608752220E0,1.55E0,1.018325618832E1)); -#6326=CARTESIAN_POINT('',(-3.004024940028E0,1.55E0,9.988123969370E0)); -#6327=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,9.792991750417E0)); -#6329=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,2.746647257959E-1)); -#6330=CARTESIAN_POINT('',(-1.620212713253E0,1.55E0,2.575906108458E-1)); -#6331=CARTESIAN_POINT('',(-1.693965805827E0,1.55E0,2.257354205418E-1)); -#6332=CARTESIAN_POINT('',(-1.807475495311E0,1.55E0,1.846964118506E-1)); -#6333=CARTESIAN_POINT('',(-1.884547613063E0,1.55E0,1.620213048244E-1)); -#6334=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.517666047689E-1)); -#6336=DIRECTION('',(0.E0,0.E0,1.E0)); -#6337=VECTOR('',#6336,1.355894835493E0); -#6338=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.517666047689E-1)); -#6339=LINE('',#6338,#6337); -#6340=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,9.180817657764E-1)); -#6341=CARTESIAN_POINT('',(-3.004254239413E0,1.55E0,1.114608323938E0)); -#6342=CARTESIAN_POINT('',(-2.463914484733E0,1.55E0,1.311134882100E0)); -#6343=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.507661440262E0)); -#6345=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6346=VECTOR('',#6345,4.910827627040E-1); -#6347=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,9.180817657764E-1)); -#6348=LINE('',#6347,#6346); -#6349=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,4.269990030724E-1)); -#6350=CARTESIAN_POINT('',(-3.669915187426E0,1.55E0,5.141501928736E-1)); -#6351=CARTESIAN_POINT('',(-3.899289232098E0,1.55E0,7.055000952881E-1)); -#6352=CARTESIAN_POINT('',(-4.161825236093E0,1.55E0,1.061164382636E0)); -#6353=CARTESIAN_POINT('',(-4.339964395968E0,1.55E0,1.453086385463E0)); -#6354=CARTESIAN_POINT('',(-4.429747574789E0,1.55E0,1.872154618193E0)); -#6355=CARTESIAN_POINT('',(-4.429103562739E0,1.55E0,2.299374203780E0)); -#6356=CARTESIAN_POINT('',(-4.338255535641E0,1.55E0,2.717599764232E0)); -#6357=CARTESIAN_POINT('',(-4.159649836747E0,1.55E0,3.108029094254E0)); -#6358=CARTESIAN_POINT('',(-3.897535141638E0,1.55E0,3.461802933253E0)); -#6359=CARTESIAN_POINT('',(-3.669133359728E0,1.55E0,3.652168495713E0)); -#6360=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,3.738820191946E0)); -#6362=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6363=VECTOR('',#6362,1.329451658673E0); -#6364=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,3.738820191946E0)); -#6365=LINE('',#6364,#6363); -#6366=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.550046587517E0)); -#6367=CARTESIAN_POINT('',(-3.285986750560E0,1.55E0,2.503153902770E0)); -#6368=CARTESIAN_POINT('',(-3.415201200344E0,1.55E0,2.456261218022E0)); -#6369=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,2.409368533274E0)); -#6371=DIRECTION('',(0.E0,0.E0,1.E0)); -#6372=VECTOR('',#6371,3.563665795030E-1); -#6373=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.550046587517E0)); -#6374=LINE('',#6373,#6372); -#6375=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.353966319546E0)); -#6376=CARTESIAN_POINT('',(-2.334606616682E0,1.55E0,3.204781935371E0)); -#6377=CARTESIAN_POINT('',(-2.745689458730E0,1.55E0,3.055597551196E0)); -#6378=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.906413167021E0)); -#6380=DIRECTION('',(0.E0,0.E0,1.E0)); -#6381=VECTOR('',#6380,6.113768855300E-1); -#6382=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.353966319546E0)); -#6383=LINE('',#6382,#6381); -#6384=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.519017541968E0)); -#6385=CARTESIAN_POINT('',(-2.745961220964E0,1.55E0,3.667792763004E0)); -#6386=CARTESIAN_POINT('',(-2.334742497799E0,1.55E0,3.816567984040E0)); -#6387=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.965343205076E0)); -#6389=DIRECTION('',(0.E0,0.E0,1.E0)); -#6390=VECTOR('',#6389,3.277524033064E-1); -#6391=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.519017541968E0)); -#6392=LINE('',#6391,#6390); -#6393=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.846769945275E0)); -#6394=CARTESIAN_POINT('',(-3.196821703419E0,1.55E0,3.836507874776E0)); -#6395=CARTESIAN_POINT('',(-3.267617117925E0,1.55E0,3.822281418096E0)); -#6396=CARTESIAN_POINT('',(-3.370278241467E0,1.55E0,3.826282414398E0)); -#6397=CARTESIAN_POINT('',(-3.453260400186E0,1.55E0,3.867724004155E0)); -#6398=CARTESIAN_POINT('',(-3.511026376279E0,1.55E0,3.940034077793E0)); -#6399=CARTESIAN_POINT('',(-3.550364059428E0,1.55E0,4.029588719334E0)); -#6400=CARTESIAN_POINT('',(-3.577434871114E0,1.55E0,4.137522770088E0)); -#6401=CARTESIAN_POINT('',(-3.592297876928E0,1.55E0,4.257412996233E0)); -#6402=CARTESIAN_POINT('',(-3.597137623280E0,1.55E0,4.394677155528E0)); -#6403=CARTESIAN_POINT('',(-3.591459875117E0,1.55E0,4.548170182436E0)); -#6404=CARTESIAN_POINT('',(-3.565880503959E0,1.55E0,4.725559501087E0)); -#6405=CARTESIAN_POINT('',(-3.504733918915E0,1.55E0,4.906399271463E0)); -#6406=CARTESIAN_POINT('',(-3.404203980925E0,1.55E0,5.067285385785E0)); -#6407=CARTESIAN_POINT('',(-3.277927727304E0,1.55E0,5.184843953642E0)); -#6408=CARTESIAN_POINT('',(-3.146454375608E0,1.55E0,5.266292111941E0)); -#6409=CARTESIAN_POINT('',(-3.021323460579E0,1.55E0,5.318959135186E0)); -#6410=CARTESIAN_POINT('',(-2.902969091898E0,1.55E0,5.346238958632E0)); -#6411=CARTESIAN_POINT('',(-2.793470908436E0,1.55E0,5.335332773683E0)); -#6412=CARTESIAN_POINT('',(-2.706455277582E0,1.55E0,5.280752382903E0)); -#6413=CARTESIAN_POINT('',(-2.647376471162E0,1.55E0,5.200835725455E0)); -#6414=CARTESIAN_POINT('',(-2.606034861335E0,1.55E0,5.109276993079E0)); -#6415=CARTESIAN_POINT('',(-2.577408899502E0,1.55E0,5.016216268724E0)); -#6416=CARTESIAN_POINT('',(-2.552947439405E0,1.55E0,4.928707344134E0)); -#6417=CARTESIAN_POINT('',(-2.528912753293E0,1.55E0,4.853786914811E0)); -#6418=CARTESIAN_POINT('',(-2.500086764451E0,1.55E0,4.789120278580E0)); -#6419=CARTESIAN_POINT('',(-2.463120703018E0,1.55E0,4.738216599066E0)); -#6420=CARTESIAN_POINT('',(-2.410785388690E0,1.55E0,4.708244416815E0)); -#6421=CARTESIAN_POINT('',(-2.352252012731E0,1.55E0,4.707222226833E0)); -#6422=CARTESIAN_POINT('',(-2.297253761183E0,1.55E0,4.727364871983E0)); -#6423=CARTESIAN_POINT('',(-2.249156763479E0,1.55E0,4.760285720910E0)); -#6424=CARTESIAN_POINT('',(-2.212441387626E0,1.55E0,4.800791762064E0)); -#6425=CARTESIAN_POINT('',(-2.188882518371E0,1.55E0,4.843663234200E0)); -#6426=CARTESIAN_POINT('',(-2.176387898204E0,1.55E0,4.885152520707E0)); -#6427=CARTESIAN_POINT('',(-2.174846630662E0,1.55E0,4.924165320916E0)); -#6428=CARTESIAN_POINT('',(-2.185509917337E0,1.55E0,4.957357257822E0)); -#6429=CARTESIAN_POINT('',(-2.207120652336E0,1.55E0,4.981741170427E0)); -#6430=CARTESIAN_POINT('',(-2.237930535033E0,1.55E0,4.992162334842E0)); -#6431=CARTESIAN_POINT('',(-2.272095552519E0,1.55E0,4.991007103051E0)); -#6432=CARTESIAN_POINT('',(-2.308504002543E0,1.55E0,4.982975727737E0)); -#6433=CARTESIAN_POINT('',(-2.348530748896E0,1.55E0,4.972754816942E0)); -#6434=CARTESIAN_POINT('',(-2.376416001770E0,1.55E0,4.965263453483E0)); -#6435=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,4.961181115669E0)); -#6437=DIRECTION('',(0.E0,0.E0,1.E0)); -#6438=VECTOR('',#6437,6.033030721040E-1); -#6439=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,4.961181115669E0)); -#6440=LINE('',#6439,#6438); -#6441=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,5.564484187773E0)); -#6442=CARTESIAN_POINT('',(-2.354357830985E0,1.55E0,5.576340476556E0)); -#6443=CARTESIAN_POINT('',(-2.288186642157E0,1.55E0,5.595380433702E0)); -#6444=CARTESIAN_POINT('',(-2.195357407806E0,1.55E0,5.616171505428E0)); -#6445=CARTESIAN_POINT('',(-2.111831957201E0,1.55E0,5.615418602152E0)); -#6446=CARTESIAN_POINT('',(-2.034076197603E0,1.55E0,5.584015125337E0)); -#6447=CARTESIAN_POINT('',(-1.972781047368E0,1.55E0,5.522551309388E0)); -#6448=CARTESIAN_POINT('',(-1.928054092846E0,1.55E0,5.439259103573E0)); -#6449=CARTESIAN_POINT('',(-1.899213171976E0,1.55E0,5.342449947031E0)); -#6450=CARTESIAN_POINT('',(-1.881113379202E0,1.55E0,5.230631831318E0)); -#6451=CARTESIAN_POINT('',(-1.872089472513E0,1.55E0,5.108584671973E0)); -#6452=CARTESIAN_POINT('',(-1.870102284188E0,1.55E0,4.971852350578E0)); -#6453=CARTESIAN_POINT('',(-1.877519906028E0,1.55E0,4.821002474585E0)); -#6454=CARTESIAN_POINT('',(-1.904720895203E0,1.55E0,4.652729311598E0)); -#6455=CARTESIAN_POINT('',(-1.965755743454E0,1.55E0,4.476901127391E0)); -#6456=CARTESIAN_POINT('',(-2.068548958876E0,1.55E0,4.310937031155E0)); -#6457=CARTESIAN_POINT('',(-2.217764594764E0,1.55E0,4.168967262148E0)); -#6458=CARTESIAN_POINT('',(-2.342435255587E0,1.55E0,4.106354389812E0)); -#6459=CARTESIAN_POINT('',(-2.410366337802E0,1.55E0,4.079032389891E0)); -#6461=CARTESIAN_POINT('',(-2.410366337802E0,1.55E0,4.079032389891E0)); -#6462=CARTESIAN_POINT('',(-2.340114457097E0,1.55E0,4.078120253680E0)); -#6463=CARTESIAN_POINT('',(-2.201678909058E0,1.55E0,4.069780563810E0)); -#6464=CARTESIAN_POINT('',(-1.995544695180E0,1.55E0,4.035143162476E0)); -#6465=CARTESIAN_POINT('',(-1.861986253924E0,1.55E0,3.997778819083E0)); -#6466=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,3.975679865447E0)); -#6468=DIRECTION('',(0.E0,0.E0,1.E0)); -#6469=VECTOR('',#6468,6.425621784628E0); -#6470=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,3.975679865447E0)); -#6471=LINE('',#6470,#6469); -#6472=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,1.043163682004E1)); -#6473=CARTESIAN_POINT('',(-1.654198907992E0,1.55E0,1.042152509672E1)); -#6474=CARTESIAN_POINT('',(-1.724746685471E0,1.55E0,1.041141337340E1)); -#6475=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,1.040130165008E1)); -#6477=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6478=VECTOR('',#6477,1.015697209424E1); -#6479=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,1.043163682004E1)); -#6480=LINE('',#6479,#6478); -#6481=DIRECTION('',(0.E0,0.E0,1.E0)); -#6482=VECTOR('',#6481,5.948581024751E-1); -#6483=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,1.452272899908E0)); -#6484=LINE('',#6483,#6482); -#6485=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,2.139253857638E0)); -#6486=CARTESIAN_POINT('',(-2.397485603616E0,1.55E0,2.108546239219E0)); -#6487=CARTESIAN_POINT('',(-2.484441025984E0,1.55E0,2.077838620801E0)); -#6488=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,2.047131002383E0)); -#6490=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6491=VECTOR('',#6490,6.414537746874E-1); -#6492=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,2.139253857638E0)); -#6493=LINE('',#6492,#6491); -#6494=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,1.636145592944E0)); -#6495=CARTESIAN_POINT('',(-2.052593850731E0,1.55E0,1.590030422946E0)); -#6496=CARTESIAN_POINT('',(-2.181562015989E0,1.55E0,1.543915252948E0)); -#6497=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,1.497800082950E0)); -#6499=DIRECTION('',(0.E0,0.E0,1.E0)); -#6500=VECTOR('',#6499,1.256509610971E0); -#6501=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,1.636145592944E0)); -#6502=LINE('',#6501,#6500); -#6503=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,2.304655147416E0)); -#6504=CARTESIAN_POINT('',(-3.003795640643E0,1.55E0,2.500655166249E0)); -#6505=CARTESIAN_POINT('',(-2.463710663058E0,1.55E0,2.696655185082E0)); -#6506=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,2.892655203915E0)); -#6508=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6509=VECTOR('',#6508,1.255996263269E0); -#6510=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,2.304655147416E0)); -#6511=LINE('',#6510,#6509); -#6512=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.187063609591E0)); -#6513=CARTESIAN_POINT('',(-3.285833884304E0,1.55E0,1.140928701110E0)); -#6514=CARTESIAN_POINT('',(-3.414857251266E0,1.55E0,1.094793792628E0)); -#6515=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,1.048658884147E0)); -#6517=DIRECTION('',(0.E0,0.E0,1.E0)); -#6518=VECTOR('',#6517,6.464951434009E-1); -#6519=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.187063609591E0)); -#6520=LINE('',#6519,#6518); -#6521=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.918446335862E0)); -#6522=CARTESIAN_POINT('',(-2.997158697330E0,1.55E0,1.890150474905E0)); -#6523=CARTESIAN_POINT('',(-3.076984607336E0,1.55E0,1.861854613949E0)); -#6524=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.833558752992E0)); -#6526=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6527=VECTOR('',#6526,5.881607088224E-1); -#6528=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.918446335862E0)); -#6529=LINE('',#6528,#6527); -#6530=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,1.452272899908E0)); -#6531=CARTESIAN_POINT('',(-2.686708561343E0,1.55E0,1.411610475618E0)); -#6532=CARTESIAN_POINT('',(-2.802020674334E0,1.55E0,1.370948051329E0)); -#6533=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.330285627040E0)); -#6535=DIRECTION('',(1.E0,0.E0,0.E0)); -#6536=VECTOR('',#6535,1.E0); -#6537=CARTESIAN_POINT('',(-4.9E-1,1.4E0,1.342E1)); -#6538=LINE('',#6537,#6536); -#6539=DIRECTION('',(0.E0,1.E0,0.E0)); -#6540=VECTOR('',#6539,1.1E0); -#6541=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.342E1)); -#6542=LINE('',#6541,#6540); -#6543=DIRECTION('',(0.E0,1.E0,0.E0)); -#6544=VECTOR('',#6543,1.25E0); -#6545=CARTESIAN_POINT('',(-5.4E0,3.E-1,1.342E1)); -#6546=LINE('',#6545,#6544); -#6547=DIRECTION('',(0.E0,1.E0,0.E0)); -#6548=VECTOR('',#6547,1.1E0); -#6549=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.342E1)); -#6550=LINE('',#6549,#6548); -#6551=DIRECTION('',(0.E0,1.E0,0.E0)); -#6552=VECTOR('',#6551,1.1E0); -#6553=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.327E1)); -#6554=LINE('',#6553,#6552); -#6555=DIRECTION('',(0.E0,1.E0,0.E0)); -#6556=VECTOR('',#6555,1.1E0); -#6557=CARTESIAN_POINT('',(-5.25E0,3.E-1,1.327E1)); -#6558=LINE('',#6557,#6556); -#6559=DIRECTION('',(0.E0,1.E0,0.E0)); -#6560=VECTOR('',#6559,1.1E0); -#6561=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.757618014356E0)); -#6562=LINE('',#6561,#6560); -#6563=DIRECTION('',(0.E0,1.E0,0.E0)); -#6564=VECTOR('',#6563,1.1E0); -#6565=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.327E1)); -#6566=LINE('',#6565,#6564); -#6567=DIRECTION('',(0.E0,1.E0,0.E0)); -#6568=VECTOR('',#6567,1.1E0); -#6569=CARTESIAN_POINT('',(6.65E0,3.E-1,1.327E1)); -#6570=LINE('',#6569,#6568); -#6571=DIRECTION('',(0.E0,1.E0,0.E0)); -#6572=VECTOR('',#6571,1.1E0); -#6573=CARTESIAN_POINT('',(6.65E0,3.E-1,8.039068448582E0)); -#6574=LINE('',#6573,#6572); -#6575=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6576=VECTOR('',#6575,5.E-2); -#6577=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,8.126726183650E0)); -#6578=LINE('',#6577,#6576); -#6579=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6580=VECTOR('',#6579,5.E-2); -#6581=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,8.070385908836E0)); -#6582=LINE('',#6581,#6580); -#6583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6584=VECTOR('',#6583,5.E-2); -#6585=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,7.985875536912E0)); -#6586=LINE('',#6585,#6584); -#6587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6588=VECTOR('',#6587,5.E-2); -#6589=CARTESIAN_POINT('',(1.319148957729E0,1.55E0,7.957705439802E0)); -#6590=LINE('',#6589,#6588); -#6591=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6592=VECTOR('',#6591,5.E-2); -#6593=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,7.957705439802E0)); -#6594=LINE('',#6593,#6592); -#6595=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6596=VECTOR('',#6595,5.E-2); -#6597=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,7.985875536912E0)); -#6598=LINE('',#6597,#6596); -#6599=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6600=VECTOR('',#6599,5.E-2); -#6601=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,8.070385908836E0)); -#6602=LINE('',#6601,#6600); -#6603=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6604=VECTOR('',#6603,5.E-2); -#6605=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,8.183066377870E0)); -#6606=LINE('',#6605,#6604); -#6607=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6608=VECTOR('',#6607,5.E-2); -#6609=CARTESIAN_POINT('',(2.E0,1.55E0,8.323917024608E0)); -#6610=LINE('',#6609,#6608); -#6611=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6612=VECTOR('',#6611,5.E-2); -#6613=CARTESIAN_POINT('',(2.E0,1.55E0,9.E0)); -#6614=LINE('',#6613,#6612); -#6615=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6616=VECTOR('',#6615,5.E-2); -#6617=CARTESIAN_POINT('',(0.E0,1.55E0,9.E0)); -#6618=LINE('',#6617,#6616); -#6619=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6620=VECTOR('',#6619,5.E-2); -#6621=CARTESIAN_POINT('',(0.E0,1.55E0,8.323917024608E0)); -#6622=LINE('',#6621,#6620); -#6623=DIRECTION('',(-1.360023205166E-14,-1.E0,3.552713678800E-14)); -#6624=VECTOR('',#6623,5.E-2); -#6625=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,8.183066377870E0)); -#6626=LINE('',#6625,#6624); -#6627=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6628=VECTOR('',#6627,5.E-2); -#6629=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,8.070385908836E0)); -#6630=LINE('',#6629,#6628); -#6631=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6632=VECTOR('',#6631,5.E-2); -#6633=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,7.985875536912E0)); -#6634=LINE('',#6633,#6632); -#6635=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6636=VECTOR('',#6635,5.E-2); -#6637=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,7.957705439802E0)); -#6638=LINE('',#6637,#6636); -#6639=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6640=VECTOR('',#6639,5.E-2); -#6641=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,7.957705439802E0)); -#6642=LINE('',#6641,#6640); -#6643=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6644=VECTOR('',#6643,5.E-2); -#6645=CARTESIAN_POINT('',(7.659574747086E-1,1.55E0,7.985875536912E0)); -#6646=LINE('',#6645,#6644); -#6647=DIRECTION('',(0.E0,-1.E0,0.E0)); -#6648=VECTOR('',#6647,5.E-2); -#6649=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,8.070385908836E0)); -#6650=LINE('',#6649,#6648); -#6651=DIRECTION('',(-6.026976445372E-1,0.E0,-7.979696418218E-1)); -#6652=VECTOR('',#6651,7.060453413469E-2); -#6653=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,8.126726183650E0)); -#6654=LINE('',#6653,#6652); -#6655=DIRECTION('',(-6.026976445372E-1,0.E0,7.979696418218E-1)); -#6656=VECTOR('',#6655,7.060453413469E-2); -#6657=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,8.070385908836E0)); -#6658=LINE('',#6657,#6656); -#6659=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#6660=VECTOR('',#6659,1.900378429420E-1); -#6661=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,7.985875536912E0)); -#6662=LINE('',#6661,#6660); -#6663=DIRECTION('',(-9.765078619901E-1,0.E0,2.154817752655E-1)); -#6664=VECTOR('',#6663,1.307307640047E-1); -#6665=CARTESIAN_POINT('',(1.319148957729E0,1.5E0,7.957705439802E0)); -#6666=LINE('',#6665,#6664); -#6667=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6668=VECTOR('',#6667,2.127659320831E-1); -#6669=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,7.957705439802E0)); -#6670=LINE('',#6669,#6668); -#6671=DIRECTION('',(-9.765078514050E-1,0.E0,-2.154818232343E-1)); -#6672=VECTOR('',#6671,1.307307349025E-1); -#6673=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,7.985875536912E0)); -#6674=LINE('',#6673,#6672); -#6675=DIRECTION('',(-8.956781764003E-1,0.E0,-4.447028269758E-1)); -#6676=VECTOR('',#6675,1.900378562887E-1); -#6677=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,8.070385908836E0)); -#6678=LINE('',#6677,#6676); -#6679=DIRECTION('',(-7.497222583060E-1,0.E0,-6.617526240224E-1)); -#6680=VECTOR('',#6679,1.702758174930E-1); -#6681=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,8.183066377870E0)); -#6682=LINE('',#6681,#6680); -#6683=DIRECTION('',(-2.892053991362E-1,0.E0,-9.572670667637E-1)); -#6684=VECTOR('',#6683,1.471382977946E-1); -#6685=CARTESIAN_POINT('',(2.E0,1.5E0,8.323917024608E0)); -#6686=LINE('',#6685,#6684); -#6687=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6688=VECTOR('',#6687,6.760829753920E-1); -#6689=CARTESIAN_POINT('',(2.E0,1.5E0,9.E0)); -#6690=LINE('',#6689,#6688); -#6691=DIRECTION('',(1.E0,0.E0,0.E0)); -#6692=VECTOR('',#6691,2.E0); -#6693=CARTESIAN_POINT('',(0.E0,1.5E0,9.E0)); -#6694=LINE('',#6693,#6692); -#6695=DIRECTION('',(0.E0,0.E0,1.E0)); -#6696=VECTOR('',#6695,6.760829753920E-1); -#6697=CARTESIAN_POINT('',(0.E0,1.5E0,8.323917024608E0)); -#6698=LINE('',#6697,#6696); -#6699=DIRECTION('',(-2.892053759356E-1,0.E0,9.572670737730E-1)); -#6700=VECTOR('',#6699,1.471382967172E-1); -#6701=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,8.183066377870E0)); -#6702=LINE('',#6701,#6700); -#6703=DIRECTION('',(-7.497222295638E-1,0.E0,6.617526565854E-1)); -#6704=VECTOR('',#6703,1.702758091142E-1); -#6705=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,8.070385908836E0)); -#6706=LINE('',#6705,#6704); -#6707=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#6708=VECTOR('',#6707,1.900378429420E-1); -#6709=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,7.985875536912E0)); -#6710=LINE('',#6709,#6708); -#6711=DIRECTION('',(-9.765078408199E-1,0.E0,2.154818712031E-1)); -#6712=VECTOR('',#6711,1.307307058003E-1); -#6713=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,7.957705439802E0)); -#6714=LINE('',#6713,#6712); -#6715=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6716=VECTOR('',#6715,1.702128648758E-1); -#6717=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,7.957705439802E0)); -#6718=LINE('',#6717,#6716); -#6719=DIRECTION('',(-9.765078408199E-1,0.E0,-2.154818712031E-1)); -#6720=VECTOR('',#6719,1.307307058003E-1); -#6721=CARTESIAN_POINT('',(7.659574747086E-1,1.5E0,7.985875536912E0)); -#6722=LINE('',#6721,#6720); -#6723=DIRECTION('',(-8.956781608936E-1,0.E0,-4.447028582079E-1)); -#6724=VECTOR('',#6723,1.900378429420E-1); -#6725=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,8.070385908836E0)); -#6726=LINE('',#6725,#6724); -#6727=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6728=VECTOR('',#6727,5.352323286535E-1); -#6729=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,8.830979256152E0)); -#6730=LINE('',#6729,#6728); -#6731=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6732=VECTOR('',#6731,5.957447290421E-1); -#6733=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,8.830979256152E0)); -#6734=LINE('',#6733,#6732); -#6735=DIRECTION('',(0.E0,0.E0,1.E0)); -#6736=VECTOR('',#6735,5.352323286535E-1); -#6737=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,8.295746927498E0)); -#6738=LINE('',#6737,#6736); -#6739=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#6740=VECTOR('',#6739,9.461911348634E-2); -#6741=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,8.211236555574E0)); -#6742=LINE('',#6741,#6740); -#6743=DIRECTION('',(8.338425497604E-1,0.E0,5.520023570683E-1)); -#6744=VECTOR('',#6743,1.020652794196E-1); -#6745=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,8.154896280760E0)); -#6746=LINE('',#6745,#6744); -#6747=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#6748=VECTOR('',#6747,1.307307058003E-1); -#6749=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,8.126726183650E0)); -#6750=LINE('',#6749,#6748); -#6751=DIRECTION('',(1.E0,0.E0,0.E0)); -#6752=VECTOR('',#6751,8.510637283325E-2); -#6753=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,8.126726183650E0)); -#6754=LINE('',#6753,#6752); -#6755=DIRECTION('',(9.765078831602E-1,0.E0,-2.154816793280E-1)); -#6756=VECTOR('',#6755,1.307308222091E-1); -#6757=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,8.154896280760E0)); -#6758=LINE('',#6757,#6756); -#6759=DIRECTION('',(8.338425497604E-1,0.E0,-5.520023570683E-1)); -#6760=VECTOR('',#6759,1.020652794196E-1); -#6761=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,8.211236555574E0)); -#6762=LINE('',#6761,#6760); -#6763=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#6764=VECTOR('',#6763,9.461911348634E-2); -#6765=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,8.295746927498E0)); -#6766=LINE('',#6765,#6764); -#6767=DIRECTION('',(1.E0,0.E0,0.E0)); -#6768=VECTOR('',#6767,1.276595592499E-1); -#6769=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,8.126726183650E0)); -#6770=LINE('',#6769,#6768); -#6771=DIRECTION('',(9.765078619901E-1,0.E0,-2.154817752655E-1)); -#6772=VECTOR('',#6771,1.307307640047E-1); -#6773=CARTESIAN_POINT('',(1.234042525291E0,1.5E0,8.154896280760E0)); -#6774=LINE('',#6773,#6772); -#6775=DIRECTION('',(8.338425497604E-1,0.E0,-5.520023570683E-1)); -#6776=VECTOR('',#6775,1.020652794196E-1); -#6777=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,8.211236555574E0)); -#6778=LINE('',#6777,#6776); -#6779=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#6780=VECTOR('',#6779,9.461911348634E-2); -#6781=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,8.295746927498E0)); -#6782=LINE('',#6781,#6780); -#6783=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6784=VECTOR('',#6783,5.352323286535E-1); -#6785=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,8.830979256152E0)); -#6786=LINE('',#6785,#6784); -#6787=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6788=VECTOR('',#6787,6.382978856564E-1); -#6789=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,8.830979256152E0)); -#6790=LINE('',#6789,#6788); -#6791=DIRECTION('',(0.E0,0.E0,1.E0)); -#6792=VECTOR('',#6791,5.352323286535E-1); -#6793=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,8.295746927498E0)); -#6794=LINE('',#6793,#6792); -#6795=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#6796=VECTOR('',#6795,9.461911348634E-2); -#6797=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,8.211236555574E0)); -#6798=LINE('',#6797,#6796); -#6799=DIRECTION('',(8.338426387325E-1,0.E0,5.520022226690E-1)); -#6800=VECTOR('',#6799,1.020653042700E-1); -#6801=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,8.154896280760E0)); -#6802=LINE('',#6801,#6800); -#6803=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#6804=VECTOR('',#6803,1.307307058003E-1); -#6805=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,8.126726183650E0)); -#6806=LINE('',#6805,#6804); -#6807=DIRECTION('',(0.E0,0.E0,1.E0)); -#6808=VECTOR('',#6807,1.070464657307E0); -#6809=CARTESIAN_POINT('',(0.E0,1.5E0,6.661879763833E0)); -#6810=LINE('',#6809,#6808); -#6811=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6812=VECTOR('',#6811,2.127659320831E-1); -#6813=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,6.661879763833E0)); -#6814=LINE('',#6813,#6812); -#6815=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6816=VECTOR('',#6815,4.507218761342E-1); -#6817=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.112601639967E0)); -#6818=LINE('',#6817,#6816); -#6819=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6820=VECTOR('',#6819,1.787234067917E0); -#6821=CARTESIAN_POINT('',(2.E0,1.5E0,7.112601639967E0)); -#6822=LINE('',#6821,#6820); -#6823=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6824=VECTOR('',#6823,1.690207438480E-1); -#6825=CARTESIAN_POINT('',(2.E0,1.5E0,7.281622383815E0)); -#6826=LINE('',#6825,#6824); -#6827=DIRECTION('',(1.E0,0.E0,0.E0)); -#6828=VECTOR('',#6827,1.787234067917E0); -#6829=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.281622383815E0)); -#6830=LINE('',#6829,#6828); -#6831=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6832=VECTOR('',#6831,4.507220373249E-1); -#6833=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.732344421140E0)); -#6834=LINE('',#6833,#6832); -#6835=DIRECTION('',(1.E0,0.E0,0.E0)); -#6836=VECTOR('',#6835,2.127659320831E-1); -#6837=CARTESIAN_POINT('',(0.E0,1.5E0,7.732344421140E0)); -#6838=LINE('',#6837,#6836); -#6839=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#6840=VECTOR('',#6839,7.060459844736E-2); -#6841=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,6.211157726508E0)); -#6842=LINE('',#6841,#6840); -#6843=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#6844=VECTOR('',#6843,7.060459844736E-2); -#6845=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,6.267498081918E0)); -#6846=LINE('',#6845,#6844); -#6847=DIRECTION('',(8.338431555277E-1,0.E0,-5.520014420087E-1)); -#6848=VECTOR('',#6847,1.530978079074E-1); -#6849=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,6.352008292651E0)); -#6850=LINE('',#6849,#6848); -#6851=DIRECTION('',(9.493458507973E-1,0.E0,-3.142331229740E-1)); -#6852=VECTOR('',#6851,1.792947696812E-1); -#6853=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,6.408348648061E0)); -#6854=LINE('',#6853,#6852); -#6855=DIRECTION('',(1.E0,0.E0,0.E0)); -#6856=VECTOR('',#6855,1.276595592499E-1); -#6857=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,6.408348648061E0)); -#6858=LINE('',#6857,#6856); -#6859=DIRECTION('',(9.666828244595E-1,0.E0,2.559771804186E-1)); -#6860=VECTOR('',#6859,2.200991327340E-1); -#6861=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,6.352008292651E0)); -#6862=LINE('',#6861,#6860); -#6863=DIRECTION('',(8.338431555277E-1,0.E0,5.520014420087E-1)); -#6864=VECTOR('',#6863,1.530978079074E-1); -#6865=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,6.267498081918E0)); -#6866=LINE('',#6865,#6864); -#6867=DIRECTION('',(6.715586697255E-1,0.E0,7.409513837740E-1)); -#6868=VECTOR('',#6867,1.900944251112E-1); -#6869=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,6.126647354584E0)); -#6870=LINE('',#6869,#6868); -#6871=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#6872=VECTOR('',#6871,1.471383738685E-1); -#6873=CARTESIAN_POINT('',(0.E0,1.5E0,5.985796627250E0)); -#6874=LINE('',#6873,#6872); -#6875=DIRECTION('',(0.E0,0.E0,1.E0)); -#6876=VECTOR('',#6875,1.126803884382E-1); -#6877=CARTESIAN_POINT('',(0.E0,1.5E0,5.873116238812E0)); -#6878=LINE('',#6877,#6876); -#6879=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#6880=VECTOR('',#6879,1.471383738685E-1); -#6881=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,5.732265511478E0)); -#6882=LINE('',#6881,#6880); -#6883=DIRECTION('',(-6.715595135938E-1,0.E0,7.409506189360E-1)); -#6884=VECTOR('',#6883,1.900941862423E-1); -#6885=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,5.591415106526E0)); -#6886=LINE('',#6885,#6884); -#6887=DIRECTION('',(-8.338426709139E-1,0.E0,5.520021740566E-1)); -#6888=VECTOR('',#6887,1.530978968850E-1); -#6889=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,5.506904734602E0)); -#6890=LINE('',#6889,#6888); -#6891=DIRECTION('',(-9.666828244595E-1,0.E0,2.559771804186E-1)); -#6892=VECTOR('',#6891,2.200991327340E-1); -#6893=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,5.450564379192E0)); -#6894=LINE('',#6893,#6892); -#6895=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6896=VECTOR('',#6895,1.276595592499E-1); -#6897=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,5.450564379192E0)); -#6898=LINE('',#6897,#6896); -#6899=DIRECTION('',(-9.493458507973E-1,0.E0,-3.142331229740E-1)); -#6900=VECTOR('',#6899,1.792947696812E-1); -#6901=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,5.506904734602E0)); -#6902=LINE('',#6901,#6900); -#6903=DIRECTION('',(-8.338426709139E-1,0.E0,-5.520021740566E-1)); -#6904=VECTOR('',#6903,1.530978968850E-1); -#6905=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,5.591415106526E0)); -#6906=LINE('',#6905,#6904); -#6907=DIRECTION('',(-6.026992915064E-1,0.E0,-7.979683978816E-1)); -#6908=VECTOR('',#6907,7.060434119686E-2); -#6909=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,5.647755139554E0)); -#6910=LINE('',#6909,#6908); -#6911=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#6912=VECTOR('',#6911,7.060434119686E-2); -#6913=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,5.591415106526E0)); -#6914=LINE('',#6913,#6912); -#6915=DIRECTION('',(-7.497215250747E-1,0.E0,6.617534547244E-1)); -#6916=VECTOR('',#6915,1.702759691169E-1); -#6917=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,5.478734395706E0)); -#6918=LINE('',#6917,#6916); -#6919=DIRECTION('',(-9.666831691551E-1,0.E0,2.559758786924E-1)); -#6920=VECTOR('',#6919,2.200989925931E-1); -#6921=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,5.422394362678E0)); -#6922=LINE('',#6921,#6920); -#6923=DIRECTION('',(-1.E0,0.E0,0.E0)); -#6924=VECTOR('',#6923,1.276595592499E-1); -#6925=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,5.422394362678E0)); -#6926=LINE('',#6925,#6924); -#6927=DIRECTION('',(-9.666831602829E-1,0.E0,-2.559759121978E-1)); -#6928=VECTOR('',#6927,2.200989637837E-1); -#6929=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,5.478734395706E0)); -#6930=LINE('',#6929,#6928); -#6931=DIRECTION('',(-8.338427005713E-1,0.E0,-5.520021292568E-1)); -#6932=VECTOR('',#6931,1.530979093102E-1); -#6933=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,5.563244767630E0)); -#6934=LINE('',#6933,#6932); -#6935=DIRECTION('',(-6.715587020024E-1,0.E0,-7.409513545199E-1)); -#6936=VECTOR('',#6935,1.900944326164E-1); -#6937=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,5.704095494964E0)); -#6938=LINE('',#6937,#6936); -#6939=DIRECTION('',(-2.892052474928E-1,0.E0,-9.572671125776E-1)); -#6940=VECTOR('',#6939,1.471383749459E-1); -#6941=CARTESIAN_POINT('',(2.E0,1.5E0,5.844946222298E0)); -#6942=LINE('',#6941,#6940); -#6943=DIRECTION('',(0.E0,0.E0,-1.E0)); -#6944=VECTOR('',#6943,1.690207438480E-1); -#6945=CARTESIAN_POINT('',(2.E0,1.5E0,6.013966966146E0)); -#6946=LINE('',#6945,#6944); -#6947=DIRECTION('',(2.892058540675E-1,0.E0,-9.572669293217E-1)); -#6948=VECTOR('',#6947,1.471380663407E-1); -#6949=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,6.154817371098E0)); -#6950=LINE('',#6949,#6948); -#6951=DIRECTION('',(6.715587020024E-1,0.E0,-7.409513545199E-1)); -#6952=VECTOR('',#6951,1.900944326164E-1); -#6953=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,6.295668098432E0)); -#6954=LINE('',#6953,#6952); -#6955=DIRECTION('',(8.338427005713E-1,0.E0,-5.520021292568E-1)); -#6956=VECTOR('',#6955,1.530979093102E-1); -#6957=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,6.380178470356E0)); -#6958=LINE('',#6957,#6956); -#6959=DIRECTION('',(9.666829790630E-1,0.E0,-2.559765965668E-1)); -#6960=VECTOR('',#6959,2.200990050447E-1); -#6961=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,6.436518664575E0)); -#6962=LINE('',#6961,#6960); -#6963=DIRECTION('',(1.E0,0.E0,0.E0)); -#6964=VECTOR('',#6963,1.276595592499E-1); -#6965=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,6.436518664575E0)); -#6966=LINE('',#6965,#6964); -#6967=DIRECTION('',(9.666829879352E-1,0.E0,2.559765630612E-1)); -#6968=VECTOR('',#6967,2.200990338541E-1); -#6969=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,6.380178470356E0)); -#6970=LINE('',#6969,#6968); -#6971=DIRECTION('',(7.497224643937E-1,0.E0,6.617523905385E-1)); -#6972=VECTOR('',#6971,1.702757557800E-1); -#6973=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,6.267498081918E0)); -#6974=LINE('',#6973,#6972); -#6975=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#6976=VECTOR('',#6975,1.204479815731E-1); -#6977=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.985796627250E0)); -#6978=LINE('',#6977,#6976); -#6979=DIRECTION('',(0.E0,0.E0,1.E0)); -#6980=VECTOR('',#6979,1.126803884382E-1); -#6981=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.873116238812E0)); -#6982=LINE('',#6981,#6980); -#6983=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#6984=VECTOR('',#6983,1.204476799809E-1); -#6985=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,5.760435850374E0)); -#6986=LINE('',#6985,#6984); -#6987=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#6988=VECTOR('',#6987,1.412091968947E-1); -#6989=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,5.647755139554E0)); -#6990=LINE('',#6989,#6988); -#6991=DIRECTION('',(8.956781919070E-1,0.E0,4.447027957437E-1)); -#6992=VECTOR('',#6991,1.900378696353E-1); -#6993=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,5.563244767630E0)); -#6994=LINE('',#6993,#6992); -#6995=DIRECTION('',(1.E0,0.E0,0.E0)); -#6996=VECTOR('',#6995,1.276595592499E-1); -#6997=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,5.563244767630E0)); -#6998=LINE('',#6997,#6996); -#6999=DIRECTION('',(8.956782229204E-1,0.E0,-4.447027332794E-1)); -#7000=VECTOR('',#6999,1.900378963286E-1); -#7001=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,5.647755139554E0)); -#7002=LINE('',#7001,#7000); -#7003=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#7004=VECTOR('',#7003,1.412091968947E-1); -#7005=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,5.760435850374E0)); -#7006=LINE('',#7005,#7004); -#7007=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#7008=VECTOR('',#7007,1.204476799809E-1); -#7009=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,5.873116238812E0)); -#7010=LINE('',#7009,#7008); -#7011=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7012=VECTOR('',#7011,1.126803884382E-1); -#7013=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,5.985796627250E0)); -#7014=LINE('',#7013,#7012); -#7015=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#7016=VECTOR('',#7015,1.204479815731E-1); -#7017=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,6.098477338070E0)); -#7018=LINE('',#7017,#7016); -#7019=DIRECTION('',(-6.026981935262E-1,0.E0,-7.979692271762E-1)); -#7020=VECTOR('',#7019,1.412089396441E-1); -#7021=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,6.211157726508E0)); -#7022=LINE('',#7021,#7020); -#7023=DIRECTION('',(-8.956782229204E-1,0.E0,-4.447027332794E-1)); -#7024=VECTOR('',#7023,1.900378963286E-1); -#7025=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,6.295668098432E0)); -#7026=LINE('',#7025,#7024); -#7027=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7028=VECTOR('',#7027,1.276595592499E-1); -#7029=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,6.295668098432E0)); -#7030=LINE('',#7029,#7028); -#7031=DIRECTION('',(-8.956781919070E-1,0.E0,4.447027957437E-1)); -#7032=VECTOR('',#7031,1.900378696353E-1); -#7033=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,6.211157726508E0)); -#7034=LINE('',#7033,#7032); -#7035=DIRECTION('',(-6.026981935262E-1,0.E0,7.979692271762E-1)); -#7036=VECTOR('',#7035,1.412089396441E-1); -#7037=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,6.098477338070E0)); -#7038=LINE('',#7037,#7036); -#7039=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#7040=VECTOR('',#7039,1.204476799809E-1); -#7041=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,5.873116238812E0)); -#7042=LINE('',#7041,#7040); -#7043=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7044=VECTOR('',#7043,1.126803884382E-1); -#7045=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,5.985796627250E0)); -#7046=LINE('',#7045,#7044); -#7047=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#7048=VECTOR('',#7047,1.204479815731E-1); -#7049=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,6.098477338070E0)); -#7050=LINE('',#7049,#7048); -#7051=DIRECTION('',(-7.497224643937E-1,0.E0,-6.617523905385E-1)); -#7052=VECTOR('',#7051,1.702757557800E-1); -#7053=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,6.211157726508E0)); -#7054=LINE('',#7053,#7052); -#7055=DIRECTION('',(-9.148651035675E-1,0.E0,-4.037596342805E-1)); -#7056=VECTOR('',#7055,1.395393462505E-1); -#7057=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,6.267498081918E0)); -#7058=LINE('',#7057,#7056); -#7059=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7060=VECTOR('',#7059,8.510637283325E-2); -#7061=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,6.267498081918E0)); -#7062=LINE('',#7061,#7060); -#7063=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498490E-1)); -#7064=VECTOR('',#7063,1.395392371900E-1); -#7065=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,6.211157726508E0)); -#7066=LINE('',#7065,#7064); -#7067=DIRECTION('',(-7.497224643937E-1,0.E0,6.617523905385E-1)); -#7068=VECTOR('',#7067,1.702757557800E-1); -#7069=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,6.098477338070E0)); -#7070=LINE('',#7069,#7068); -#7071=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#7072=VECTOR('',#7071,1.204479815731E-1); -#7073=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,5.985796627250E0)); -#7074=LINE('',#7073,#7072); -#7075=DIRECTION('',(0.E0,0.E0,1.E0)); -#7076=VECTOR('',#7075,1.126803884382E-1); -#7077=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,5.873116238812E0)); -#7078=LINE('',#7077,#7076); -#7079=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#7080=VECTOR('',#7079,1.204476799809E-1); -#7081=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,5.760435850374E0)); -#7082=LINE('',#7081,#7080); -#7083=DIRECTION('',(7.497215250746E-1,0.E0,6.617534547244E-1)); -#7084=VECTOR('',#7083,1.702759691169E-1); -#7085=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,5.647755139554E0)); -#7086=LINE('',#7085,#7084); -#7087=DIRECTION('',(9.148658176982E-1,0.E0,4.037580161524E-1)); -#7088=VECTOR('',#7087,1.395391070256E-1); -#7089=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,5.591415106526E0)); -#7090=LINE('',#7089,#7088); -#7091=DIRECTION('',(1.E0,0.E0,0.E0)); -#7092=VECTOR('',#7091,8.510637283325E-2); -#7093=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,5.591415106526E0)); -#7094=LINE('',#7093,#7092); -#7095=DIRECTION('',(9.148659569677E-1,0.E0,-4.037577005848E-1)); -#7096=VECTOR('',#7095,1.395392160861E-1); -#7097=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,5.647755139554E0)); -#7098=LINE('',#7097,#7096); -#7099=DIRECTION('',(7.497215250746E-1,0.E0,-6.617534547244E-1)); -#7100=VECTOR('',#7099,1.702759691169E-1); -#7101=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,5.760435850374E0)); -#7102=LINE('',#7101,#7100); -#7103=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498490E-1)); -#7104=VECTOR('',#7103,1.395392371900E-1); -#7105=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.267419172256E0)); -#7106=LINE('',#7105,#7104); -#7107=DIRECTION('',(-7.095871007418E-1,0.E0,-7.046177307313E-1)); -#7108=VECTOR('',#7107,1.199379014154E-1); -#7109=CARTESIAN_POINT('',(1.872340425849E0,1.5E0,4.351929544180E0)); -#7110=LINE('',#7109,#7108); -#7111=DIRECTION('',(-6.026982439217E-1,0.E0,-7.979691891130E-1)); -#7112=VECTOR('',#7111,1.412089463798E-1); -#7113=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,4.464609932618E0)); -#7114=LINE('',#7113,#7112); -#7115=DIRECTION('',(-3.532910151020E-1,0.E0,-9.355134732585E-1)); -#7116=VECTOR('',#7115,1.204479828892E-1); -#7117=CARTESIAN_POINT('',(2.E0,1.5E0,4.577290643438E0)); -#7118=LINE('',#7117,#7116); -#7119=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7120=VECTOR('',#7119,2.253607768763E-1); -#7121=CARTESIAN_POINT('',(2.E0,1.5E0,4.802651420314E0)); -#7122=LINE('',#7121,#7120); -#7123=DIRECTION('',(3.532910151020E-1,0.E0,-9.355134732585E-1)); -#7124=VECTOR('',#7123,1.204479828892E-1); -#7125=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,4.915332131134E0)); -#7126=LINE('',#7125,#7124); -#7127=DIRECTION('',(6.026982439217E-1,0.E0,-7.979691891130E-1)); -#7128=VECTOR('',#7127,1.412089463798E-1); -#7129=CARTESIAN_POINT('',(1.872340425849E0,1.5E0,5.028012519572E0)); -#7130=LINE('',#7129,#7128); -#7131=DIRECTION('',(7.095871007418E-1,0.E0,-7.046177307313E-1)); -#7132=VECTOR('',#7131,1.199379014154E-1); -#7133=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.112522891496E0)); -#7134=LINE('',#7133,#7132); -#7135=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#7136=VECTOR('',#7135,1.395392371900E-1); -#7137=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,5.168863246906E0)); -#7138=LINE('',#7137,#7136); -#7139=DIRECTION('',(9.765079811284E-1,0.E0,-2.154812353607E-1)); -#7140=VECTOR('',#7139,1.307307175356E-1); -#7141=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,5.197033263420E0)); -#7142=LINE('',#7141,#7140); -#7143=DIRECTION('',(0.E0,0.E0,1.E0)); -#7144=VECTOR('',#7143,1.408507273338E-1); -#7145=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,5.056182536086E0)); -#7146=LINE('',#7145,#7144); -#7147=DIRECTION('',(-9.493463871840E-1,0.E0,3.142315024639E-1)); -#7148=VECTOR('',#7147,8.964733418926E-2); -#7149=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,5.028012519572E0)); -#7150=LINE('',#7149,#7148); -#7151=DIRECTION('',(-8.338422752723E-1,0.E0,5.520027717038E-1)); -#7152=VECTOR('',#7151,1.020653487589E-1); -#7153=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,4.971672164162E0)); -#7154=LINE('',#7153,#7152); -#7155=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#7156=VECTOR('',#7155,7.060434119686E-2); -#7157=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,4.915332131134E0)); -#7158=LINE('',#7157,#7156); -#7159=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#7160=VECTOR('',#7159,1.471383738685E-1); -#7161=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.774481403800E0)); -#7162=LINE('',#7161,#7160); -#7163=DIRECTION('',(0.E0,0.E0,1.E0)); -#7164=VECTOR('',#7163,1.690207438480E-1); -#7165=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.605460659952E0)); -#7166=LINE('',#7165,#7164); -#7167=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#7168=VECTOR('',#7167,1.471383738685E-1); -#7169=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,4.464609932618E0)); -#7170=LINE('',#7169,#7168); -#7171=DIRECTION('',(6.026992915064E-1,0.E0,7.979683978816E-1)); -#7172=VECTOR('',#7171,7.060434119686E-2); -#7173=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,4.408269899590E0)); -#7174=LINE('',#7173,#7172); -#7175=DIRECTION('',(8.338422752723E-1,0.E0,5.520027717038E-1)); -#7176=VECTOR('',#7175,1.020653487589E-1); -#7177=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,4.351929544180E0)); -#7178=LINE('',#7177,#7176); -#7179=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#7180=VECTOR('',#7179,8.964733418926E-2); -#7181=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,4.323759527666E0)); -#7182=LINE('',#7181,#7180); -#7183=DIRECTION('',(1.E0,0.E0,0.E0)); -#7184=VECTOR('',#7183,1.702127456665E-1); -#7185=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,4.323759527666E0)); -#7186=LINE('',#7185,#7184); -#7187=DIRECTION('',(9.493464200095E-1,0.E0,-3.142314032923E-1)); -#7188=VECTOR('',#7187,1.792947249640E-1); -#7189=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,4.380099560694E0)); -#7190=LINE('',#7189,#7188); -#7191=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#7192=VECTOR('',#7191,1.199378908417E-1); -#7193=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,4.464609932618E0)); -#7194=LINE('',#7193,#7192); -#7195=DIRECTION('',(2.441444645688E-1,0.E0,-9.697388722849E-1)); -#7196=VECTOR('',#7195,1.742951104453E-1); -#7197=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.633630676466E0)); -#7198=LINE('',#7197,#7196); -#7199=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7200=VECTOR('',#7199,1.126807108197E-1); -#7201=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.746311387286E0)); -#7202=LINE('',#7201,#7200); -#7203=DIRECTION('',(1.E0,0.E0,0.E0)); -#7204=VECTOR('',#7203,1.702127456665E-1); -#7205=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,4.746311387286E0)); -#7206=LINE('',#7205,#7204); -#7207=DIRECTION('',(0.E0,0.E0,1.E0)); -#7208=VECTOR('',#7207,1.126807108197E-1); -#7209=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,4.633630676466E0)); -#7210=LINE('',#7209,#7208); -#7211=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#7212=VECTOR('',#7211,1.892382269727E-1); -#7213=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,4.464609932618E0)); -#7214=LINE('',#7213,#7212); -#7215=DIRECTION('',(8.338436401413E-1,0.E0,5.520007099595E-1)); -#7216=VECTOR('',#7215,1.020651459533E-1); -#7217=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,4.408269899590E0)); -#7218=LINE('',#7217,#7216); -#7219=DIRECTION('',(9.493458507973E-1,0.E0,3.142331229740E-1)); -#7220=VECTOR('',#7219,1.792947696812E-1); -#7221=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,4.351929544180E0)); -#7222=LINE('',#7221,#7220); -#7223=DIRECTION('',(1.E0,0.E0,0.E0)); -#7224=VECTOR('',#7223,8.510649204254E-2); -#7225=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,4.351929544180E0)); -#7226=LINE('',#7225,#7224); -#7227=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#7228=VECTOR('',#7227,1.395392371900E-1); -#7229=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,4.408269899590E0)); -#7230=LINE('',#7229,#7228); -#7231=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#7232=VECTOR('',#7231,1.199378908417E-1); -#7233=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,4.492780271514E0)); -#7234=LINE('',#7233,#7232); -#7235=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#7236=VECTOR('',#7235,1.471380652634E-1); -#7237=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,4.633630676466E0)); -#7238=LINE('',#7237,#7236); -#7239=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7240=VECTOR('',#7239,1.126807108197E-1); -#7241=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,4.746311387286E0)); -#7242=LINE('',#7241,#7240); -#7243=DIRECTION('',(-2.892058308668E-1,0.E0,-9.572669363311E-1)); -#7244=VECTOR('',#7243,1.471380652634E-1); -#7245=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,4.887161792238E0)); -#7246=LINE('',#7245,#7244); -#7247=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#7248=VECTOR('',#7247,1.199378908417E-1); -#7249=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,4.971672164162E0)); -#7250=LINE('',#7249,#7248); -#7251=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498491E-1)); -#7252=VECTOR('',#7251,1.395392371900E-1); -#7253=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,5.028012519572E0)); -#7254=LINE('',#7253,#7252); -#7255=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7256=VECTOR('',#7255,1.408507273338E-1); -#7257=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,5.168863246906E0)); -#7258=LINE('',#7257,#7256); -#7259=DIRECTION('',(9.865798174491E-1,0.E0,1.632797103197E-1)); -#7260=VECTOR('',#7259,1.725281043217E-1); -#7261=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,5.140692908010E0)); -#7262=LINE('',#7261,#7260); -#7263=DIRECTION('',(8.338429132208E-1,0.E0,5.520018080328E-1)); -#7264=VECTOR('',#7263,2.041304698616E-1); -#7265=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,5.028012519572E0)); -#7266=LINE('',#7265,#7264); -#7267=DIRECTION('',(6.026981935262E-1,0.E0,7.979692271762E-1)); -#7268=VECTOR('',#7267,1.412089396441E-1); -#7269=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,4.915332131134E0)); -#7270=LINE('',#7269,#7268); -#7271=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#7272=VECTOR('',#7271,2.017302574921E-1); -#7273=CARTESIAN_POINT('',(0.E0,1.5E0,4.718141048390E0)); -#7274=LINE('',#7273,#7272); -#7275=DIRECTION('',(0.E0,0.E0,1.E0)); -#7276=VECTOR('',#7275,5.634003302834E-2); -#7277=CARTESIAN_POINT('',(0.E0,1.5E0,4.661801015362E0)); -#7278=LINE('',#7277,#7276); -#7279=DIRECTION('',(-2.109410206761E-1,0.E0,9.774987906878E-1)); -#7280=VECTOR('',#7279,2.017302574921E-1); -#7281=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,4.464609932618E0)); -#7282=LINE('',#7281,#7280); -#7283=DIRECTION('',(-6.026981935262E-1,0.E0,7.979692271762E-1)); -#7284=VECTOR('',#7283,1.412089396441E-1); -#7285=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,4.351929544180E0)); -#7286=LINE('',#7285,#7284); -#7287=DIRECTION('',(-8.338429132208E-1,0.E0,5.520018080328E-1)); -#7288=VECTOR('',#7287,2.041304698616E-1); -#7289=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,4.239249155742E0)); -#7290=LINE('',#7289,#7288); -#7291=DIRECTION('',(-9.865798174491E-1,0.E0,1.632797103197E-1)); -#7292=VECTOR('',#7291,1.725281043217E-1); -#7293=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,4.211078816846E0)); -#7294=LINE('',#7293,#7292); -#7295=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7296=VECTOR('',#7295,8.510649204254E-2); -#7297=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,4.211078816846E0)); -#7298=LINE('',#7297,#7296); -#7299=DIRECTION('',(-9.865798174491E-1,0.E0,-1.632797103197E-1)); -#7300=VECTOR('',#7299,1.725281043217E-1); -#7301=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,4.239249155742E0)); -#7302=LINE('',#7301,#7300); -#7303=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#7304=VECTOR('',#7303,1.395391070256E-1); -#7305=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,4.295589188770E0)); -#7306=LINE('',#7305,#7304); -#7307=DIRECTION('',(-7.497215250747E-1,0.E0,-6.617534547244E-1)); -#7308=VECTOR('',#7307,1.702759691169E-1); -#7309=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,4.408269899590E0)); -#7310=LINE('',#7309,#7308); -#7311=DIRECTION('',(-5.171559642137E-1,0.E0,8.558911780584E-1)); -#7312=VECTOR('',#7311,1.645661632514E-1); -#7313=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.267419172256E0)); -#7314=LINE('',#7313,#7312); -#7315=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498490E-1)); -#7316=VECTOR('',#7315,1.395392371900E-1); -#7317=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,4.211078816846E0)); -#7318=LINE('',#7317,#7316); -#7319=DIRECTION('',(-9.865801276635E-1,0.E0,1.632778359099E-1)); -#7320=VECTOR('',#7319,1.725281104884E-1); -#7321=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,4.182908800332E0)); -#7322=LINE('',#7321,#7320); -#7323=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7324=VECTOR('',#7323,1.702127456665E-1); -#7325=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,4.182908800332E0)); -#7326=LINE('',#7325,#7324); -#7327=DIRECTION('',(-9.765079811284E-1,0.E0,-2.154812353607E-1)); -#7328=VECTOR('',#7327,1.307307175356E-1); -#7329=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,4.211078816846E0)); -#7330=LINE('',#7329,#7328); -#7331=DIRECTION('',(1.E0,0.E0,0.E0)); -#7332=VECTOR('',#7331,2.127659618855E-1); -#7333=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,3.957547701074E0)); -#7334=LINE('',#7333,#7332); -#7335=DIRECTION('',(8.032893743823E-1,0.E0,5.955889362677E-1)); -#7336=VECTOR('',#7335,1.324341867015E0); -#7337=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,3.168784337244E0)); -#7338=LINE('',#7337,#7336); -#7339=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#7340=VECTOR('',#7339,1.792946683785E-1); -#7341=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,3.112444304216E0)); -#7342=LINE('',#7341,#7340); -#7343=DIRECTION('',(1.E0,0.E0,0.E0)); -#7344=VECTOR('',#7343,8.510649204254E-2); -#7345=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.112444304216E0)); -#7346=LINE('',#7345,#7344); -#7347=DIRECTION('',(9.148658176982E-1,0.E0,-4.037580161524E-1)); -#7348=VECTOR('',#7347,1.395391070256E-1); -#7349=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,3.168784337244E0)); -#7350=LINE('',#7349,#7348); -#7351=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#7352=VECTOR('',#7351,1.199378908417E-1); -#7353=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,3.253294709168E0)); -#7354=LINE('',#7353,#7352); -#7355=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#7356=VECTOR('',#7355,1.471380652634E-1); -#7357=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,3.394145114120E0)); -#7358=LINE('',#7357,#7356); -#7359=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7360=VECTOR('',#7359,1.126807108197E-1); -#7361=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,3.506825824940E0)); -#7362=LINE('',#7361,#7360); -#7363=DIRECTION('',(-2.892052242921E-1,0.E0,-9.572671195869E-1)); -#7364=VECTOR('',#7363,1.471383738685E-1); -#7365=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,3.647676552274E0)); -#7366=LINE('',#7365,#7364); -#7367=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#7368=VECTOR('',#7367,1.199378908417E-1); -#7369=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,3.732186924198E0)); -#7370=LINE('',#7369,#7368); -#7371=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#7372=VECTOR('',#7371,1.395391070256E-1); -#7373=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.788526957226E0)); -#7374=LINE('',#7373,#7372); -#7375=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7376=VECTOR('',#7375,1.408507273338E-1); -#7377=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.929377684560E0)); -#7378=LINE('',#7377,#7376); -#7379=DIRECTION('',(9.865801184532E-1,0.E0,1.632778915618E-1)); -#7380=VECTOR('',#7379,1.725280516836E-1); -#7381=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,3.901207668046E0)); -#7382=LINE('',#7381,#7380); -#7383=DIRECTION('',(8.338421863001E-1,0.E0,5.520029061031E-1)); -#7384=VECTOR('',#7383,2.041306478169E-1); -#7385=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,3.788526957226E0)); -#7386=LINE('',#7385,#7384); -#7387=DIRECTION('',(6.026981935263E-1,0.E0,7.979692271762E-1)); -#7388=VECTOR('',#7387,1.412089396441E-1); -#7389=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,3.675846568788E0)); -#7390=LINE('',#7389,#7388); -#7391=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#7392=VECTOR('',#7391,2.017302574921E-1); -#7393=CARTESIAN_POINT('',(0.E0,1.5E0,3.478655486044E0)); -#7394=LINE('',#7393,#7392); -#7395=DIRECTION('',(0.E0,0.E0,1.E0)); -#7396=VECTOR('',#7395,1.126800660567E-1); -#7397=CARTESIAN_POINT('',(0.E0,1.5E0,3.365975419988E0)); -#7398=LINE('',#7397,#7396); -#7399=DIRECTION('',(-2.441444645688E-1,0.E0,9.697388722849E-1)); -#7400=VECTOR('',#7399,1.742951104453E-1); -#7401=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,3.196954676140E0)); -#7402=LINE('',#7401,#7400); -#7403=DIRECTION('',(-6.026970955489E-1,0.E0,7.979700564663E-1)); -#7404=VECTOR('',#7403,1.412091968947E-1); -#7405=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,3.084273965320E0)); -#7406=LINE('',#7405,#7404); -#7407=DIRECTION('',(-8.338421863001E-1,0.E0,5.520029061031E-1)); -#7408=VECTOR('',#7407,2.041306478169E-1); -#7409=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,2.971593254501E0)); -#7410=LINE('',#7409,#7408); -#7411=DIRECTION('',(-9.865804194541E-1,0.E0,1.632760728023E-1)); -#7412=VECTOR('',#7411,1.725279990461E-1); -#7413=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,2.943423560368E0)); -#7414=LINE('',#7413,#7412); -#7415=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7416=VECTOR('',#7415,8.510649204254E-2); -#7417=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,2.943423560368E0)); -#7418=LINE('',#7417,#7416); -#7419=DIRECTION('',(-9.865804194541E-1,0.E0,-1.632760728023E-1)); -#7420=VECTOR('',#7419,1.725279990461E-1); -#7421=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,2.971593254501E0)); -#7422=LINE('',#7421,#7420); -#7423=DIRECTION('',(-9.148641108930E-1,0.E0,-4.037618835403E-1)); -#7424=VECTOR('',#7423,1.395393673551E-1); -#7425=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,3.027933932292E0)); -#7426=LINE('',#7425,#7424); -#7427=DIRECTION('',(-7.991283277492E-1,0.E0,-6.011604742403E-1)); -#7428=VECTOR('',#7427,1.171489181480E0); -#7429=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,3.732186924198E0)); -#7430=LINE('',#7429,#7428); -#7431=DIRECTION('',(0.E0,0.E0,1.E0)); -#7432=VECTOR('',#7431,7.887633638302E-1); -#7433=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,2.943423560368E0)); -#7434=LINE('',#7433,#7432); -#7435=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7436=VECTOR('',#7435,2.127659618855E-1); -#7437=CARTESIAN_POINT('',(2.E0,1.5E0,2.943423560368E0)); -#7438=LINE('',#7437,#7436); -#7439=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7440=VECTOR('',#7439,1.014124140706E0); -#7441=CARTESIAN_POINT('',(2.E0,1.5E0,3.957547701074E0)); -#7442=LINE('',#7441,#7440); -#7443=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7444=VECTOR('',#7443,1.690207438480E-1); -#7445=CARTESIAN_POINT('',(2.E0,1.5E0,1.760278353432E0)); -#7446=LINE('',#7445,#7444); -#7447=DIRECTION('',(8.987745446082E-1,0.E0,-4.384111289239E-1)); -#7448=VECTOR('',#7447,8.995700489911E-1); -#7449=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,2.154659874156E0)); -#7450=LINE('',#7449,#7448); -#7451=DIRECTION('',(-8.987745446082E-1,0.E0,-4.384111289239E-1)); -#7452=VECTOR('',#7451,8.995700489911E-1); -#7453=CARTESIAN_POINT('',(2.E0,1.5E0,2.549041394881E0)); -#7454=LINE('',#7453,#7452); -#7455=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7456=VECTOR('',#7455,1.690207438480E-1); -#7457=CARTESIAN_POINT('',(2.E0,1.5E0,2.718062138729E0)); -#7458=LINE('',#7457,#7456); -#7459=DIRECTION('',(9.054015226808E-1,0.E0,4.245563363410E-1)); -#7460=VECTOR('',#7459,1.127981970015E0); -#7461=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,2.239170246080E0)); -#7462=LINE('',#7461,#7460); -#7463=DIRECTION('',(8.982376862285E-1,0.E0,-4.395100215454E-1)); -#7464=VECTOR('',#7463,1.089604034430E0); -#7465=CARTESIAN_POINT('',(0.E0,1.5E0,2.718062138729E0)); -#7466=LINE('',#7465,#7464); -#7467=DIRECTION('',(0.E0,0.E0,1.E0)); -#7468=VECTOR('',#7467,1.690207438480E-1); -#7469=CARTESIAN_POINT('',(0.E0,1.5E0,2.549041394881E0)); -#7470=LINE('',#7469,#7468); -#7471=DIRECTION('',(-8.987745446082E-1,0.E0,4.384111289239E-1)); -#7472=VECTOR('',#7471,8.995700489911E-1); -#7473=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,2.154659874156E0)); -#7474=LINE('',#7473,#7472); -#7475=DIRECTION('',(8.987745446082E-1,0.E0,4.384111289239E-1)); -#7476=VECTOR('',#7475,8.995700489911E-1); -#7477=CARTESIAN_POINT('',(0.E0,1.5E0,1.760278353432E0)); -#7478=LINE('',#7477,#7476); -#7479=DIRECTION('',(0.E0,0.E0,1.E0)); -#7480=VECTOR('',#7479,1.690207438480E-1); -#7481=CARTESIAN_POINT('',(0.E0,1.5E0,1.591257609584E0)); -#7482=LINE('',#7481,#7480); -#7483=DIRECTION('',(-8.982376862285E-1,0.E0,-4.395100215454E-1)); -#7484=VECTOR('',#7483,1.089604034430E0); -#7485=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,2.070149502232E0)); -#7486=LINE('',#7485,#7484); -#7487=DIRECTION('',(-9.054015226808E-1,0.E0,4.245563363410E-1)); -#7488=VECTOR('',#7487,1.127981970015E0); -#7489=CARTESIAN_POINT('',(2.E0,1.5E0,1.591257609584E0)); -#7490=LINE('',#7489,#7488); -#7491=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7492=VECTOR('',#7491,4.680851101875E-1); -#7493=CARTESIAN_POINT('',(4.E0,1.5E0,1.03375E1)); -#7494=LINE('',#7493,#7492); -#7495=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7496=VECTOR('',#7495,1.125E-1); -#7497=CARTESIAN_POINT('',(4.E0,1.5E0,1.045E1)); -#7498=LINE('',#7497,#7496); -#7499=DIRECTION('',(1.E0,0.E0,0.E0)); -#7500=VECTOR('',#7499,1.E0); -#7501=CARTESIAN_POINT('',(3.E0,1.5E0,1.045E1)); -#7502=LINE('',#7501,#7500); -#7503=DIRECTION('',(0.E0,0.E0,1.E0)); -#7504=VECTOR('',#7503,6.75E-1); -#7505=CARTESIAN_POINT('',(3.E0,1.5E0,9.775E0)); -#7506=LINE('',#7505,#7504); -#7507=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7508=VECTOR('',#7507,1.276595592499E-1); -#7509=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.775E0)); -#7510=LINE('',#7509,#7508); -#7511=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7512=VECTOR('',#7511,5.625E-1); -#7513=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.03375E1)); -#7514=LINE('',#7513,#7512); -#7515=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7516=VECTOR('',#7515,2.765957713127E-1); -#7517=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.03375E1)); -#7518=LINE('',#7517,#7516); -#7519=DIRECTION('',(0.E0,0.E0,1.E0)); -#7520=VECTOR('',#7519,4.875000178814E-1); -#7521=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,9.849999982119E0)); -#7522=LINE('',#7521,#7520); -#7523=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7524=VECTOR('',#7523,1.276595592499E-1); -#7525=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,9.849999982119E0)); -#7526=LINE('',#7525,#7524); -#7527=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7528=VECTOR('',#7527,4.875000178814E-1); -#7529=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.03375E1)); -#7530=LINE('',#7529,#7528); -#7531=DIRECTION('',(0.E0,0.E0,1.E0)); -#7532=VECTOR('',#7531,1.125E-1); -#7533=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.893750035763E0)); -#7534=LINE('',#7533,#7532); -#7535=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#7536=VECTOR('',#7535,1.080226756383E-1); -#7537=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.912499964237E0)); -#7538=LINE('',#7537,#7536); -#7539=DIRECTION('',(-7.502480643278E-1,0.E0,-6.611564428881E-1)); -#7540=VECTOR('',#7539,1.134376539313E-1); -#7541=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.9875E0)); -#7542=LINE('',#7541,#7540); -#7543=DIRECTION('',(-4.934792445233E-1,0.E0,-8.697575726745E-1)); -#7544=VECTOR('',#7543,8.623096609801E-2); -#7545=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.062500035763E0)); -#7546=LINE('',#7545,#7544); -#7547=DIRECTION('',(-2.213222297055E-1,0.E0,-9.752007335099E-1)); -#7548=VECTOR('',#7547,9.613401735230E-2); -#7549=CARTESIAN_POINT('',(4.E0,1.5E0,9.15625E0)); -#7550=LINE('',#7549,#7548); -#7551=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7552=VECTOR('',#7551,1.6875E-1); -#7553=CARTESIAN_POINT('',(4.E0,1.5E0,9.325E0)); -#7554=LINE('',#7553,#7552); -#7555=DIRECTION('',(2.213222297055E-1,0.E0,-9.752007335099E-1)); -#7556=VECTOR('',#7555,9.613401735230E-2); -#7557=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.418749964237E0)); -#7558=LINE('',#7557,#7556); -#7559=DIRECTION('',(4.934792445233E-1,0.E0,-8.697575726745E-1)); -#7560=VECTOR('',#7559,8.623096609801E-2); -#7561=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,9.49375E0)); -#7562=LINE('',#7561,#7560); -#7563=DIRECTION('',(7.502482988989E-1,0.E0,-6.611561767082E-1)); -#7564=VECTOR('',#7563,1.134376184641E-1); -#7565=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.568749982119E0)); -#7566=LINE('',#7565,#7564); -#7567=DIRECTION('',(9.151040085600E-1,0.E0,-4.032178735094E-1)); -#7568=VECTOR('',#7567,9.300187403652E-2); -#7569=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,9.60625E0)); -#7570=LINE('',#7569,#7568); -#7571=DIRECTION('',(9.848207396759E-1,0.E0,-1.735745105259E-1)); -#7572=VECTOR('',#7571,1.080226702746E-1); -#7573=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,9.624999982119E0)); -#7574=LINE('',#7573,#7572); -#7575=DIRECTION('',(1.E0,0.E0,0.E0)); -#7576=VECTOR('',#7575,3.191489279270E-1); -#7577=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,9.624999982119E0)); -#7578=LINE('',#7577,#7576); -#7579=DIRECTION('',(9.848207562999E-1,0.E0,1.735744162049E-1)); -#7580=VECTOR('',#7579,1.080227289745E-1); -#7581=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,9.60625E0)); -#7582=LINE('',#7581,#7580); -#7583=DIRECTION('',(9.151039825100E-1,0.E0,4.032179326300E-1)); -#7584=VECTOR('',#7583,9.300186040041E-2); -#7585=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.568749982119E0)); -#7586=LINE('',#7585,#7584); -#7587=DIRECTION('',(7.502482701883E-1,0.E0,6.611562092875E-1)); -#7588=VECTOR('',#7587,1.134376128743E-1); -#7589=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,9.49375E0)); -#7590=LINE('',#7589,#7588); -#7591=DIRECTION('',(4.934791955020E-1,0.E0,8.697576004880E-1)); -#7592=VECTOR('',#7591,8.623096334048E-2); -#7593=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.418749964237E0)); -#7594=LINE('',#7593,#7592); -#7595=DIRECTION('',(2.213222112791E-1,0.E0,9.752007376918E-1)); -#7596=VECTOR('',#7595,9.613401694006E-2); -#7597=CARTESIAN_POINT('',(3.E0,1.5E0,9.325E0)); -#7598=LINE('',#7597,#7596); -#7599=DIRECTION('',(0.E0,0.E0,1.E0)); -#7600=VECTOR('',#7599,1.6875E-1); -#7601=CARTESIAN_POINT('',(3.E0,1.5E0,9.15625E0)); -#7602=LINE('',#7601,#7600); -#7603=DIRECTION('',(-2.213222112791E-1,0.E0,9.752007376918E-1)); -#7604=VECTOR('',#7603,9.613401694006E-2); -#7605=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.062500035763E0)); -#7606=LINE('',#7605,#7604); -#7607=DIRECTION('',(-4.934791955020E-1,0.E0,8.697576004880E-1)); -#7608=VECTOR('',#7607,8.623096334048E-2); -#7609=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.9875E0)); -#7610=LINE('',#7609,#7608); -#7611=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#7612=VECTOR('',#7611,1.134376483415E-1); -#7613=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.912499964237E0)); -#7614=LINE('',#7613,#7612); -#7615=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#7616=VECTOR('',#7615,1.080227196632E-1); -#7617=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.893750035763E0)); -#7618=LINE('',#7617,#7616); -#7619=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7620=VECTOR('',#7619,1.125E-1); -#7621=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,9.006250035763E0)); -#7622=LINE('',#7621,#7620); -#7623=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#7624=VECTOR('',#7623,6.652674795802E-2); -#7625=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,9.024999964237E0)); -#7626=LINE('',#7625,#7624); -#7627=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#7628=VECTOR('',#7627,7.053251855852E-2); -#7629=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.081249964237E0)); -#7630=LINE('',#7629,#7628); -#7631=DIRECTION('',(2.729182037179E-1,0.E0,-9.620372415242E-1)); -#7632=VECTOR('',#7631,7.795959711909E-2); -#7633=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.15625E0)); -#7634=LINE('',#7633,#7632); -#7635=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7636=VECTOR('',#7635,1.6875E-1); -#7637=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.325E0)); -#7638=LINE('',#7637,#7636); -#7639=DIRECTION('',(-2.729182037179E-1,0.E0,-9.620372415242E-1)); -#7640=VECTOR('',#7639,7.795959711909E-2); -#7641=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.400000035763E0)); -#7642=LINE('',#7641,#7640); -#7643=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#7644=VECTOR('',#7643,7.053251855852E-2); -#7645=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,9.456250035763E0)); -#7646=LINE('',#7645,#7644); -#7647=DIRECTION('',(-8.622115378113E-1,0.E0,-5.065483827484E-1)); -#7648=VECTOR('',#7647,7.403037007787E-2); -#7649=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,9.49375E0)); -#7650=LINE('',#7649,#7648); -#7651=DIRECTION('',(-9.765802913621E-1,0.E0,-2.151532814604E-1)); -#7652=VECTOR('',#7651,8.714733810013E-2); -#7653=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,9.512500035763E0)); -#7654=LINE('',#7653,#7652); -#7655=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7656=VECTOR('',#7655,3.191489279270E-1); -#7657=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,9.512500035763E0)); -#7658=LINE('',#7657,#7656); -#7659=DIRECTION('',(-9.765802913621E-1,0.E0,2.151532814604E-1)); -#7660=VECTOR('',#7659,8.714733810013E-2); -#7661=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,9.49375E0)); -#7662=LINE('',#7661,#7660); -#7663=DIRECTION('',(-8.622113312198E-1,0.E0,5.065487343940E-1)); -#7664=VECTOR('',#7663,7.403031868607E-2); -#7665=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,9.456250035763E0)); -#7666=LINE('',#7665,#7664); -#7667=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#7668=VECTOR('',#7667,7.053252754859E-2); -#7669=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.400000035763E0)); -#7670=LINE('',#7669,#7668); -#7671=DIRECTION('',(-2.729182037179E-1,0.E0,9.620372415242E-1)); -#7672=VECTOR('',#7671,7.795959711909E-2); -#7673=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.325E0)); -#7674=LINE('',#7673,#7672); -#7675=DIRECTION('',(0.E0,0.E0,1.E0)); -#7676=VECTOR('',#7675,1.6875E-1); -#7677=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.15625E0)); -#7678=LINE('',#7677,#7676); -#7679=DIRECTION('',(2.729182037179E-1,0.E0,9.620372415242E-1)); -#7680=VECTOR('',#7679,7.795959711909E-2); -#7681=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.081249964237E0)); -#7682=LINE('',#7681,#7680); -#7683=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#7684=VECTOR('',#7683,7.053252754859E-2); -#7685=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,9.024999964237E0)); -#7686=LINE('',#7685,#7684); -#7687=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906686E-1)); -#7688=VECTOR('',#7687,6.652669076968E-2); -#7689=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,9.006250035763E0)); -#7690=LINE('',#7689,#7688); -#7691=DIRECTION('',(0.E0,0.E0,1.E0)); -#7692=VECTOR('',#7691,1.125E-1); -#7693=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.012500071526E0)); -#7694=LINE('',#7693,#7692); -#7695=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#7696=VECTOR('',#7695,1.080226756383E-1); -#7697=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.03125E0)); -#7698=LINE('',#7697,#7696); -#7699=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#7700=VECTOR('',#7699,1.134375829969E-1); -#7701=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.106249928474E0)); -#7702=LINE('',#7701,#7700); -#7703=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#7704=VECTOR('',#7703,8.623105941289E-2); -#7705=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,8.181250071526E0)); -#7706=LINE('',#7705,#7704); -#7707=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#7708=VECTOR('',#7707,9.613391272461E-2); -#7709=CARTESIAN_POINT('',(4.E0,1.5E0,8.274999928474E0)); -#7710=LINE('',#7709,#7708); -#7711=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7712=VECTOR('',#7711,1.6875E-1); -#7713=CARTESIAN_POINT('',(4.E0,1.5E0,8.443749928474E0)); -#7714=LINE('',#7713,#7712); -#7715=DIRECTION('',(2.213219888292E-1,0.E0,-9.752007881768E-1)); -#7716=VECTOR('',#7715,9.613412197999E-2); -#7717=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,8.5375E0)); -#7718=LINE('',#7717,#7716); -#7719=DIRECTION('',(4.934797785425E-1,0.E0,-8.697572696849E-1)); -#7720=VECTOR('',#7719,8.623087278316E-2); -#7721=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.612499928474E0)); -#7722=LINE('',#7721,#7720); -#7723=DIRECTION('',(7.502480643277E-1,0.E0,-6.611564428881E-1)); -#7724=VECTOR('',#7723,1.134376539313E-1); -#7725=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.687499964237E0)); -#7726=LINE('',#7725,#7724); -#7727=DIRECTION('',(9.151037957258E-1,0.E0,-4.032183565367E-1)); -#7728=VECTOR('',#7727,9.300189566683E-2); -#7729=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,8.725000035763E0)); -#7730=LINE('',#7729,#7728); -#7731=DIRECTION('',(9.848208245646E-1,0.E0,-1.735740288863E-1)); -#7732=VECTOR('',#7731,1.080226609633E-1); -#7733=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,8.743749964237E0)); -#7734=LINE('',#7733,#7732); -#7735=DIRECTION('',(1.E0,0.E0,0.E0)); -#7736=VECTOR('',#7735,3.191489279270E-1); -#7737=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,8.743749964237E0)); -#7738=LINE('',#7737,#7736); -#7739=DIRECTION('',(9.848208411886E-1,0.E0,1.735739345656E-1)); -#7740=VECTOR('',#7739,1.080227196632E-1); -#7741=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,8.725000035763E0)); -#7742=LINE('',#7741,#7740); -#7743=DIRECTION('',(9.151037696758E-1,0.E0,4.032184156573E-1)); -#7744=VECTOR('',#7743,9.300188203072E-2); -#7745=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.687499964237E0)); -#7746=LINE('',#7745,#7744); -#7747=DIRECTION('',(7.502480356172E-1,0.E0,6.611564754674E-1)); -#7748=VECTOR('',#7747,1.134376483415E-1); -#7749=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.612499928474E0)); -#7750=LINE('',#7749,#7748); -#7751=DIRECTION('',(4.934797295212E-1,0.E0,8.697572974984E-1)); -#7752=VECTOR('',#7751,8.623087002563E-2); -#7753=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,8.5375E0)); -#7754=LINE('',#7753,#7752); -#7755=DIRECTION('',(2.213219704028E-1,0.E0,9.752007923587E-1)); -#7756=VECTOR('',#7755,9.613412156775E-2); -#7757=CARTESIAN_POINT('',(3.E0,1.5E0,8.443749928474E0)); -#7758=LINE('',#7757,#7756); -#7759=DIRECTION('',(0.E0,0.E0,1.E0)); -#7760=VECTOR('',#7759,1.6875E-1); -#7761=CARTESIAN_POINT('',(3.E0,1.5E0,8.274999928474E0)); -#7762=LINE('',#7761,#7760); -#7763=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#7764=VECTOR('',#7763,9.613391231237E-2); -#7765=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,8.181250071526E0)); -#7766=LINE('',#7765,#7764); -#7767=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#7768=VECTOR('',#7767,8.623105665536E-2); -#7769=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.106249928474E0)); -#7770=LINE('',#7769,#7768); -#7771=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#7772=VECTOR('',#7771,1.134375774071E-1); -#7773=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.03125E0)); -#7774=LINE('',#7773,#7772); -#7775=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#7776=VECTOR('',#7775,1.080227196632E-1); -#7777=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.012500071526E0)); -#7778=LINE('',#7777,#7776); -#7779=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7780=VECTOR('',#7779,1.125E-1); -#7781=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.125000071526E0)); -#7782=LINE('',#7781,#7780); -#7783=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#7784=VECTOR('',#7783,6.652674795802E-2); -#7785=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,8.14375E0)); -#7786=LINE('',#7785,#7784); -#7787=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#7788=VECTOR('',#7787,7.053251855852E-2); -#7789=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.2E0)); -#7790=LINE('',#7789,#7788); -#7791=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#7792=VECTOR('',#7791,7.795949390370E-2); -#7793=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,8.274999928474E0)); -#7794=LINE('',#7793,#7792); -#7795=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7796=VECTOR('',#7795,1.6875E-1); -#7797=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,8.443749928474E0)); -#7798=LINE('',#7797,#7796); -#7799=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#7800=VECTOR('',#7799,7.795970033450E-2); -#7801=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.518750071526E0)); -#7802=LINE('',#7801,#7800); -#7803=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#7804=VECTOR('',#7803,7.053251855852E-2); -#7805=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,8.575000071526E0)); -#7806=LINE('',#7805,#7804); -#7807=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#7808=VECTOR('',#7807,7.403031573119E-2); -#7809=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.612499928474E0)); -#7810=LINE('',#7809,#7808); -#7811=DIRECTION('',(-9.765800326865E-1,0.E0,-2.151544555851E-1)); -#7812=VECTOR('',#7811,8.714736118363E-2); -#7813=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,8.631250071526E0)); -#7814=LINE('',#7813,#7812); -#7815=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7816=VECTOR('',#7815,3.191489279270E-1); -#7817=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,8.631250071526E0)); -#7818=LINE('',#7817,#7816); -#7819=DIRECTION('',(-9.765800326865E-1,0.E0,2.151544555851E-1)); -#7820=VECTOR('',#7819,8.714736118363E-2); -#7821=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.612499928474E0)); -#7822=LINE('',#7821,#7820); -#7823=DIRECTION('',(-8.622119641820E-1,0.E0,5.065476570090E-1)); -#7824=VECTOR('',#7823,7.403026433934E-2); -#7825=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,8.575000071526E0)); -#7826=LINE('',#7825,#7824); -#7827=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#7828=VECTOR('',#7827,7.053252754859E-2); -#7829=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.518750071526E0)); -#7830=LINE('',#7829,#7828); -#7831=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#7832=VECTOR('',#7831,7.795970033450E-2); -#7833=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,8.443749928474E0)); -#7834=LINE('',#7833,#7832); -#7835=DIRECTION('',(0.E0,0.E0,1.E0)); -#7836=VECTOR('',#7835,1.6875E-1); -#7837=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,8.274999928474E0)); -#7838=LINE('',#7837,#7836); -#7839=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#7840=VECTOR('',#7839,7.795949390370E-2); -#7841=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.2E0)); -#7842=LINE('',#7841,#7840); -#7843=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#7844=VECTOR('',#7843,7.053252754859E-2); -#7845=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,8.14375E0)); -#7846=LINE('',#7845,#7844); -#7847=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906686E-1)); -#7848=VECTOR('',#7847,6.652669076968E-2); -#7849=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.125000071526E0)); -#7850=LINE('',#7849,#7848); -#7851=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7852=VECTOR('',#7851,1.E0); -#7853=CARTESIAN_POINT('',(4.E0,1.5E0,7.75E0)); -#7854=LINE('',#7853,#7852); -#7855=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7856=VECTOR('',#7855,1.125E-1); -#7857=CARTESIAN_POINT('',(4.E0,1.5E0,7.8625E0)); -#7858=LINE('',#7857,#7856); -#7859=DIRECTION('',(1.E0,0.E0,0.E0)); -#7860=VECTOR('',#7859,1.E0); -#7861=CARTESIAN_POINT('',(3.E0,1.5E0,7.8625E0)); -#7862=LINE('',#7861,#7860); -#7863=DIRECTION('',(0.E0,0.E0,1.E0)); -#7864=VECTOR('',#7863,1.125E-1); -#7865=CARTESIAN_POINT('',(3.E0,1.5E0,7.75E0)); -#7866=LINE('',#7865,#7864); -#7867=DIRECTION('',(0.E0,0.E0,1.E0)); -#7868=VECTOR('',#7867,4.5E-1); -#7869=CARTESIAN_POINT('',(3.E0,1.5E0,7.149999928474E0)); -#7870=LINE('',#7869,#7868); -#7871=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#7872=VECTOR('',#7871,9.613391231237E-2); -#7873=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,7.056250071526E0)); -#7874=LINE('',#7873,#7872); -#7875=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#7876=VECTOR('',#7875,8.623105665537E-2); -#7877=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,6.981249928474E0)); -#7878=LINE('',#7877,#7876); -#7879=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#7880=VECTOR('',#7879,1.134375774071E-1); -#7881=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,6.90625E0)); -#7882=LINE('',#7881,#7880); -#7883=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#7884=VECTOR('',#7883,9.300188203072E-2); -#7885=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,6.868749928474E0)); -#7886=LINE('',#7885,#7884); -#7887=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345656E-1)); -#7888=VECTOR('',#7887,1.080227196632E-1); -#7889=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,6.85E0)); -#7890=LINE('',#7889,#7888); -#7891=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7892=VECTOR('',#7891,3.191489279270E-1); -#7893=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,6.85E0)); -#7894=LINE('',#7893,#7892); -#7895=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#7896=VECTOR('',#7895,1.080226609633E-1); -#7897=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,6.868749928474E0)); -#7898=LINE('',#7897,#7896); -#7899=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#7900=VECTOR('',#7899,9.300189566683E-2); -#7901=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,6.90625E0)); -#7902=LINE('',#7901,#7900); -#7903=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#7904=VECTOR('',#7903,1.134375829969E-1); -#7905=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,6.981249928474E0)); -#7906=LINE('',#7905,#7904); -#7907=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#7908=VECTOR('',#7907,8.623105941289E-2); -#7909=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,7.056250071526E0)); -#7910=LINE('',#7909,#7908); -#7911=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#7912=VECTOR('',#7911,9.613391272461E-2); -#7913=CARTESIAN_POINT('',(4.E0,1.5E0,7.149999928474E0)); -#7914=LINE('',#7913,#7912); -#7915=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7916=VECTOR('',#7915,4.5E-1); -#7917=CARTESIAN_POINT('',(4.E0,1.5E0,7.599999928474E0)); -#7918=LINE('',#7917,#7916); -#7919=DIRECTION('',(1.E0,0.E0,0.E0)); -#7920=VECTOR('',#7919,1.E0); -#7921=CARTESIAN_POINT('',(3.E0,1.5E0,7.599999928474E0)); -#7922=LINE('',#7921,#7920); -#7923=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7924=VECTOR('',#7923,3.375E-1); -#7925=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,7.487499928474E0)); -#7926=LINE('',#7925,#7924); -#7927=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7928=VECTOR('',#7927,7.446808665991E-1); -#7929=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,7.487499928474E0)); -#7930=LINE('',#7929,#7928); -#7931=DIRECTION('',(0.E0,0.E0,1.E0)); -#7932=VECTOR('',#7931,3.375E-1); -#7933=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,7.149999928474E0)); -#7934=LINE('',#7933,#7932); -#7935=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#7936=VECTOR('',#7935,7.795949390370E-2); -#7937=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,7.075E0)); -#7938=LINE('',#7937,#7936); -#7939=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#7940=VECTOR('',#7939,7.053252754859E-2); -#7941=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,7.01875E0)); -#7942=LINE('',#7941,#7940); -#7943=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117766E-1)); -#7944=VECTOR('',#7943,7.403037303291E-2); -#7945=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,6.981249928474E0)); -#7946=LINE('',#7945,#7944); -#7947=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#7948=VECTOR('',#7947,8.714731501675E-2); -#7949=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,6.9625E0)); -#7950=LINE('',#7949,#7948); -#7951=DIRECTION('',(1.E0,0.E0,0.E0)); -#7952=VECTOR('',#7951,3.191489279270E-1); -#7953=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,6.9625E0)); -#7954=LINE('',#7953,#7952); -#7955=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#7956=VECTOR('',#7955,8.714731501675E-2); -#7957=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,6.981249928474E0)); -#7958=LINE('',#7957,#7956); -#7959=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#7960=VECTOR('',#7959,7.403042442468E-2); -#7961=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,7.01875E0)); -#7962=LINE('',#7961,#7960); -#7963=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#7964=VECTOR('',#7963,7.053251855852E-2); -#7965=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,7.075E0)); -#7966=LINE('',#7965,#7964); -#7967=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#7968=VECTOR('',#7967,7.795949390370E-2); -#7969=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,7.149999928474E0)); -#7970=LINE('',#7969,#7968); -#7971=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7972=VECTOR('',#7971,1.063829809427E-1); -#7973=CARTESIAN_POINT('',(4.E0,1.5E0,6.606249856949E0)); -#7974=LINE('',#7973,#7972); -#7975=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7976=VECTOR('',#7975,9.375028610230E-2); -#7977=CARTESIAN_POINT('',(4.E0,1.5E0,6.700000143051E0)); -#7978=LINE('',#7977,#7976); -#7979=DIRECTION('',(1.E0,0.E0,0.E0)); -#7980=VECTOR('',#7979,1.063829809427E-1); -#7981=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,6.700000143051E0)); -#7982=LINE('',#7981,#7980); -#7983=DIRECTION('',(0.E0,0.E0,1.E0)); -#7984=VECTOR('',#7983,9.375028610230E-2); -#7985=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,6.606249856949E0)); -#7986=LINE('',#7985,#7984); -#7987=DIRECTION('',(-1.E0,0.E0,0.E0)); -#7988=VECTOR('',#7987,1.063829660416E-1); -#7989=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.606249856949E0)); -#7990=LINE('',#7989,#7988); -#7991=DIRECTION('',(0.E0,0.E0,-1.E0)); -#7992=VECTOR('',#7991,9.375028610230E-2); -#7993=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.700000143051E0)); -#7994=LINE('',#7993,#7992); -#7995=DIRECTION('',(1.E0,0.E0,0.E0)); -#7996=VECTOR('',#7995,1.063829660416E-1); -#7997=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,6.700000143051E0)); -#7998=LINE('',#7997,#7996); -#7999=DIRECTION('',(0.E0,0.E0,1.E0)); -#8000=VECTOR('',#7999,9.375028610230E-2); -#8001=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,6.606249856949E0)); -#8002=LINE('',#8001,#8000); -#8003=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8004=VECTOR('',#8003,1.125E-1); -#8005=CARTESIAN_POINT('',(4.E0,1.5E0,5.818749856949E0)); -#8006=LINE('',#8005,#8004); -#8007=DIRECTION('',(8.386953909536E-1,0.E0,-5.446008090273E-1)); -#8008=VECTOR('',#8007,4.820049506925E-1); -#8009=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,6.081250143051E0)); -#8010=LINE('',#8009,#8008); -#8011=DIRECTION('',(-8.386957976250E-1,0.E0,-5.446001827453E-1)); -#8012=VECTOR('',#8011,4.820047169753E-1); -#8013=CARTESIAN_POINT('',(4.E0,1.5E0,6.34375E0)); -#8014=LINE('',#8013,#8012); -#8015=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8016=VECTOR('',#8015,1.125E-1); -#8017=CARTESIAN_POINT('',(4.E0,1.5E0,6.45625E0)); -#8018=LINE('',#8017,#8016); -#8019=DIRECTION('',(8.482961329975E-1,0.E0,5.295221154414E-1)); -#8020=VECTOR('',#8019,6.019575909179E-1); -#8021=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.137500143051E0)); -#8022=LINE('',#8021,#8020); -#8023=DIRECTION('',(8.379231265752E-1,0.E0,-5.457882684251E-1)); -#8024=VECTOR('',#8023,5.840174210205E-1); -#8025=CARTESIAN_POINT('',(3.E0,1.5E0,6.45625E0)); -#8026=LINE('',#8025,#8024); -#8027=DIRECTION('',(0.E0,0.E0,1.E0)); -#8028=VECTOR('',#8027,1.125E-1); -#8029=CARTESIAN_POINT('',(3.E0,1.5E0,6.34375E0)); -#8030=LINE('',#8029,#8028); -#8031=DIRECTION('',(-8.386957976250E-1,0.E0,5.446001827453E-1)); -#8032=VECTOR('',#8031,4.820047169753E-1); -#8033=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,6.081250143051E0)); -#8034=LINE('',#8033,#8032); -#8035=DIRECTION('',(8.386953909536E-1,0.E0,5.446008090273E-1)); -#8036=VECTOR('',#8035,4.820049506925E-1); -#8037=CARTESIAN_POINT('',(3.E0,1.5E0,5.818749856949E0)); -#8038=LINE('',#8037,#8036); -#8039=DIRECTION('',(0.E0,0.E0,1.E0)); -#8040=VECTOR('',#8039,1.125E-1); -#8041=CARTESIAN_POINT('',(3.E0,1.5E0,5.706249856949E0)); -#8042=LINE('',#8041,#8040); -#8043=DIRECTION('',(-8.379227905164E-1,0.E0,-5.457887843600E-1)); -#8044=VECTOR('',#8043,5.840176552475E-1); -#8045=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.025000143051E0)); -#8046=LINE('',#8045,#8044); -#8047=DIRECTION('',(-8.482958127554E-1,0.E0,5.295226284698E-1)); -#8048=VECTOR('',#8047,6.019578181643E-1); -#8049=CARTESIAN_POINT('',(4.E0,1.5E0,5.706249856949E0)); -#8050=LINE('',#8049,#8048); -#8051=DIRECTION('',(4.934807975625E-1,0.E0,8.697566915162E-1)); -#8052=VECTOR('',#8051,4.311534169801E-2); -#8053=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,5.406250143051E0)); -#8054=LINE('',#8053,#8052); -#8055=DIRECTION('',(4.934807975625E-1,0.E0,-8.697566915162E-1)); -#8056=VECTOR('',#8055,4.311534169801E-2); -#8057=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,5.44375E0)); -#8058=LINE('',#8057,#8056); -#8059=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#8060=VECTOR('',#8059,8.507821852253E-2); -#8061=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,5.5E0)); -#8062=LINE('',#8061,#8060); -#8063=DIRECTION('',(9.151046210116E-1,0.E0,-4.032164835459E-1)); -#8064=VECTOR('',#8063,9.300179550964E-2); -#8065=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,5.537499856949E0)); -#8066=LINE('',#8065,#8064); -#8067=DIRECTION('',(1.E0,0.E0,0.E0)); -#8068=VECTOR('',#8067,6.382977962494E-2); -#8069=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,5.537499856949E0)); -#8070=LINE('',#8069,#8068); -#8071=DIRECTION('',(9.431212905670E-1,0.E0,3.324488400931E-1)); -#8072=VECTOR('',#8071,1.127988803882E-1); -#8073=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,5.5E0)); -#8074=LINE('',#8073,#8072); -#8075=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#8076=VECTOR('',#8075,8.507821852253E-2); -#8077=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,5.44375E0)); -#8078=LINE('',#8077,#8076); -#8079=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#8080=VECTOR('',#8079,1.134163852576E-1); -#8081=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,5.350000143051E0)); -#8082=LINE('',#8081,#8080); -#8083=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#8084=VECTOR('',#8083,9.613433082315E-2); -#8085=CARTESIAN_POINT('',(3.E0,1.5E0,5.256249856949E0)); -#8086=LINE('',#8085,#8084); -#8087=DIRECTION('',(0.E0,0.E0,1.E0)); -#8088=VECTOR('',#8087,7.499971389771E-2); -#8089=CARTESIAN_POINT('',(3.E0,1.5E0,5.181250143051E0)); -#8090=LINE('',#8089,#8088); -#8091=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#8092=VECTOR('',#8091,9.613433082315E-2); -#8093=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,5.087499856949E0)); -#8094=LINE('',#8093,#8092); -#8095=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#8096=VECTOR('',#8095,1.134163852576E-1); -#8097=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,4.99375E0)); -#8098=LINE('',#8097,#8096); -#8099=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#8100=VECTOR('',#8099,8.507821852253E-2); -#8101=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,4.9375E0)); -#8102=LINE('',#8101,#8100); -#8103=DIRECTION('',(-9.431212905670E-1,0.E0,3.324488400931E-1)); -#8104=VECTOR('',#8103,1.127988803882E-1); -#8105=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,4.900000143051E0)); -#8106=LINE('',#8105,#8104); -#8107=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8108=VECTOR('',#8107,6.382977962494E-2); -#8109=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,4.900000143051E0)); -#8110=LINE('',#8109,#8108); -#8111=DIRECTION('',(-9.151046210116E-1,0.E0,-4.032164835459E-1)); -#8112=VECTOR('',#8111,9.300179550964E-2); -#8113=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,4.9375E0)); -#8114=LINE('',#8113,#8112); -#8115=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#8116=VECTOR('',#8115,8.507821852253E-2); -#8117=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,4.99375E0)); -#8118=LINE('',#8117,#8116); -#8119=DIRECTION('',(-4.934807975625E-1,0.E0,-8.697566915162E-1)); -#8120=VECTOR('',#8119,4.311534169801E-2); -#8121=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,5.031249856949E0)); -#8122=LINE('',#8121,#8120); -#8123=DIRECTION('',(-4.934807975625E-1,0.E0,8.697566915162E-1)); -#8124=VECTOR('',#8123,4.311534169801E-2); -#8125=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,4.99375E0)); -#8126=LINE('',#8125,#8124); -#8127=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#8128=VECTOR('',#8127,9.848483245993E-2); -#8129=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,4.918749856949E0)); -#8130=LINE('',#8129,#8128); -#8131=DIRECTION('',(-9.431212613662E-1,0.E0,3.324489229327E-1)); -#8132=VECTOR('',#8131,1.127988522810E-1); -#8133=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.88125E0)); -#8134=LINE('',#8133,#8132); -#8135=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8136=VECTOR('',#8135,6.382977962494E-2); -#8137=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,4.88125E0)); -#8138=LINE('',#8137,#8136); -#8139=DIRECTION('',(-9.431212467657E-1,0.E0,-3.324489643525E-1)); -#8140=VECTOR('',#8139,1.127988382274E-1); -#8141=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,4.918749856949E0)); -#8142=LINE('',#8141,#8140); -#8143=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#8144=VECTOR('',#8143,8.507822411232E-2); -#8145=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,4.974999856949E0)); -#8146=LINE('',#8145,#8144); -#8147=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#8148=VECTOR('',#8147,1.134167431404E-1); -#8149=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,5.068750143051E0)); -#8150=LINE('',#8149,#8148); -#8151=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#8152=VECTOR('',#8151,9.613391272461E-2); -#8153=CARTESIAN_POINT('',(4.E0,1.5E0,5.1625E0)); -#8154=LINE('',#8153,#8152); -#8155=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8156=VECTOR('',#8155,1.125E-1); -#8157=CARTESIAN_POINT('',(4.E0,1.5E0,5.275E0)); -#8158=LINE('',#8157,#8156); -#8159=DIRECTION('',(2.213224705823E-1,0.E0,-9.752006788427E-1)); -#8160=VECTOR('',#8159,9.613391272461E-2); -#8161=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,5.368749856949E0)); -#8162=LINE('',#8161,#8160); -#8163=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#8164=VECTOR('',#8163,1.134167431404E-1); -#8165=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,5.462500143051E0)); -#8166=LINE('',#8165,#8164); -#8167=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#8168=VECTOR('',#8167,8.507822411232E-2); -#8169=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,5.518750143051E0)); -#8170=LINE('',#8169,#8168); -#8171=DIRECTION('',(9.431212467657E-1,0.E0,-3.324489643525E-1)); -#8172=VECTOR('',#8171,1.127988382274E-1); -#8173=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,5.55625E0)); -#8174=LINE('',#8173,#8172); -#8175=DIRECTION('',(1.E0,0.E0,0.E0)); -#8176=VECTOR('',#8175,6.382977962494E-2); -#8177=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.55625E0)); -#8178=LINE('',#8177,#8176); -#8179=DIRECTION('',(9.431212613662E-1,0.E0,3.324489229327E-1)); -#8180=VECTOR('',#8179,1.127988522810E-1); -#8181=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,5.518750143051E0)); -#8182=LINE('',#8181,#8180); -#8183=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#8184=VECTOR('',#8183,9.848483245993E-2); -#8185=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,5.44375E0)); -#8186=LINE('',#8185,#8184); -#8187=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#8188=VECTOR('',#8187,7.795970033450E-2); -#8189=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.256249856949E0)); -#8190=LINE('',#8189,#8188); -#8191=DIRECTION('',(0.E0,0.E0,1.E0)); -#8192=VECTOR('',#8191,7.499971389771E-2); -#8193=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.181250143051E0)); -#8194=LINE('',#8193,#8192); -#8195=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#8196=VECTOR('',#8195,7.795970033450E-2); -#8197=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,5.10625E0)); -#8198=LINE('',#8197,#8196); -#8199=DIRECTION('',(4.934786614838E-1,0.E0,8.697579034767E-1)); -#8200=VECTOR('',#8199,8.623105665537E-2); -#8201=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,5.031249856949E0)); -#8202=LINE('',#8201,#8200); -#8203=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654784E-1)); -#8204=VECTOR('',#8203,1.020154877124E-1); -#8205=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,4.974999856949E0)); -#8206=LINE('',#8205,#8204); -#8207=DIRECTION('',(1.E0,0.E0,0.E0)); -#8208=VECTOR('',#8207,6.382977962494E-2); -#8209=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.974999856949E0)); -#8210=LINE('',#8209,#8208); -#8211=DIRECTION('',(8.342497220099E-1,0.E0,-5.513867982882E-1)); -#8212=VECTOR('',#8211,1.020155001437E-1); -#8213=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,5.031249856949E0)); -#8214=LINE('',#8213,#8212); -#8215=DIRECTION('',(4.934786614838E-1,0.E0,-8.697579034767E-1)); -#8216=VECTOR('',#8215,8.623105665537E-2); -#8217=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,5.10625E0)); -#8218=LINE('',#8217,#8216); -#8219=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#8220=VECTOR('',#8219,7.795970033450E-2); -#8221=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.181250143051E0)); -#8222=LINE('',#8221,#8220); -#8223=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8224=VECTOR('',#8223,7.499971389771E-2); -#8225=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.256249856949E0)); -#8226=LINE('',#8225,#8224); -#8227=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#8228=VECTOR('',#8227,7.795970033450E-2); -#8229=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,5.33125E0)); -#8230=LINE('',#8229,#8228); -#8231=DIRECTION('',(-4.934786614838E-1,0.E0,-8.697579034767E-1)); -#8232=VECTOR('',#8231,8.623105665537E-2); -#8233=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,5.406250143051E0)); -#8234=LINE('',#8233,#8232); -#8235=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#8236=VECTOR('',#8235,1.020155001437E-1); -#8237=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.462500143051E0)); -#8238=LINE('',#8237,#8236); -#8239=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8240=VECTOR('',#8239,6.382977962494E-2); -#8241=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,5.462500143051E0)); -#8242=LINE('',#8241,#8240); -#8243=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654784E-1)); -#8244=VECTOR('',#8243,1.020154877124E-1); -#8245=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,5.406250143051E0)); -#8246=LINE('',#8245,#8244); -#8247=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#8248=VECTOR('',#8247,8.623105665537E-2); -#8249=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,5.33125E0)); -#8250=LINE('',#8249,#8248); -#8251=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#8252=VECTOR('',#8251,7.795970033450E-2); -#8253=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,5.181250143051E0)); -#8254=LINE('',#8253,#8252); -#8255=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8256=VECTOR('',#8255,7.499971389771E-2); -#8257=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,5.256249856949E0)); -#8258=LINE('',#8257,#8256); -#8259=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#8260=VECTOR('',#8259,7.795970033450E-2); -#8261=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,5.33125E0)); -#8262=LINE('',#8261,#8260); -#8263=DIRECTION('',(-6.481178678037E-1,0.E0,-7.615400379714E-1)); -#8264=VECTOR('',#8263,9.848483245993E-2); -#8265=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,5.406250143051E0)); -#8266=LINE('',#8265,#8264); -#8267=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#8268=VECTOR('',#8267,7.403031573118E-2); -#8269=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,5.44375E0)); -#8270=LINE('',#8269,#8268); -#8271=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8272=VECTOR('',#8271,4.255318641663E-2); -#8273=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,5.44375E0)); -#8274=LINE('',#8273,#8272); -#8275=DIRECTION('',(-8.622119641820E-1,0.E0,5.065476570090E-1)); -#8276=VECTOR('',#8275,7.403026433934E-2); -#8277=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.406250143051E0)); -#8278=LINE('',#8277,#8276); -#8279=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#8280=VECTOR('',#8279,9.848483245993E-2); -#8281=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.33125E0)); -#8282=LINE('',#8281,#8280); -#8283=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#8284=VECTOR('',#8283,7.795970033450E-2); -#8285=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,5.256249856949E0)); -#8286=LINE('',#8285,#8284); -#8287=DIRECTION('',(0.E0,0.E0,1.E0)); -#8288=VECTOR('',#8287,7.499971389771E-2); -#8289=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,5.181250143051E0)); -#8290=LINE('',#8289,#8288); -#8291=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#8292=VECTOR('',#8291,7.795970033450E-2); -#8293=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.10625E0)); -#8294=LINE('',#8293,#8292); -#8295=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#8296=VECTOR('',#8295,9.848483245993E-2); -#8297=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.031249856949E0)); -#8298=LINE('',#8297,#8296); -#8299=DIRECTION('',(8.622119641820E-1,0.E0,5.065476570090E-1)); -#8300=VECTOR('',#8299,7.403026433934E-2); -#8301=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,4.99375E0)); -#8302=LINE('',#8301,#8300); -#8303=DIRECTION('',(1.E0,0.E0,0.E0)); -#8304=VECTOR('',#8303,4.255318641663E-2); -#8305=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,4.99375E0)); -#8306=LINE('',#8305,#8304); -#8307=DIRECTION('',(8.622121707728E-1,0.E0,-5.065473053637E-1)); -#8308=VECTOR('',#8307,7.403031573118E-2); -#8309=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,5.031249856949E0)); -#8310=LINE('',#8309,#8308); -#8311=DIRECTION('',(6.481178678037E-1,0.E0,-7.615400379714E-1)); -#8312=VECTOR('',#8311,9.848483245993E-2); -#8313=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,5.10625E0)); -#8314=LINE('',#8313,#8312); -#8315=DIRECTION('',(-9.832219306424E-1,0.E0,-1.824133632822E-1)); -#8316=VECTOR('',#8315,8.223073915743E-1); -#8317=CARTESIAN_POINT('',(4.E0,1.5E0,4.43125E0)); -#8318=LINE('',#8317,#8316); -#8319=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8320=VECTOR('',#8319,1.499998569489E-1); -#8321=CARTESIAN_POINT('',(4.E0,1.5E0,4.581249856949E0)); -#8322=LINE('',#8321,#8320); -#8323=DIRECTION('',(9.889363113616E-1,0.E0,-1.483407296412E-1)); -#8324=VECTOR('',#8323,1.011187463248E0); -#8325=CARTESIAN_POINT('',(3.E0,1.5E0,4.731250143051E0)); -#8326=LINE('',#8325,#8324); -#8327=DIRECTION('',(0.E0,0.E0,1.E0)); -#8328=VECTOR('',#8327,1.125E-1); -#8329=CARTESIAN_POINT('',(3.E0,1.5E0,4.618750143051E0)); -#8330=LINE('',#8329,#8328); -#8331=DIRECTION('',(-9.893852990515E-1,0.E0,1.453159661591E-1)); -#8332=VECTOR('',#8331,7.741750818822E-1); -#8333=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.506250143051E0)); -#8334=LINE('',#8333,#8332); -#8335=DIRECTION('',(9.813590695907E-1,0.E0,1.921831848318E-1)); -#8336=VECTOR('',#8335,7.805068181881E-1); -#8337=CARTESIAN_POINT('',(3.E0,1.5E0,4.356249856949E0)); -#8338=LINE('',#8337,#8336); -#8339=DIRECTION('',(0.E0,0.E0,1.E0)); -#8340=VECTOR('',#8339,1.499998569489E-1); -#8341=CARTESIAN_POINT('',(3.E0,1.5E0,4.20625E0)); -#8342=LINE('',#8341,#8340); -#8343=DIRECTION('',(-9.813591732907E-1,0.E0,1.921826553002E-1)); -#8344=VECTOR('',#8343,7.805067357121E-1); -#8345=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.056250143051E0)); -#8346=LINE('',#8345,#8344); -#8347=DIRECTION('',(9.893852990515E-1,0.E0,1.453159661591E-1)); -#8348=VECTOR('',#8347,7.741750818822E-1); -#8349=CARTESIAN_POINT('',(3.E0,1.5E0,3.943750143051E0)); -#8350=LINE('',#8349,#8348); -#8351=DIRECTION('',(0.E0,0.E0,1.E0)); -#8352=VECTOR('',#8351,1.125E-1); -#8353=CARTESIAN_POINT('',(3.E0,1.5E0,3.831250143051E0)); -#8354=LINE('',#8353,#8352); -#8355=DIRECTION('',(-9.889363736216E-1,0.E0,-1.483403145748E-1)); -#8356=VECTOR('',#8355,1.011187399588E0); -#8357=CARTESIAN_POINT('',(4.E0,1.5E0,3.98125E0)); -#8358=LINE('',#8357,#8356); -#8359=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8360=VECTOR('',#8359,1.499998569489E-1); -#8361=CARTESIAN_POINT('',(4.E0,1.5E0,4.131249856949E0)); -#8362=LINE('',#8361,#8360); -#8363=DIRECTION('',(9.832218370399E-1,0.E0,-1.824138678057E-1)); -#8364=VECTOR('',#8363,8.223074698577E-1); -#8365=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,4.281250143051E0)); -#8366=LINE('',#8365,#8364); -#8367=DIRECTION('',(-4.934850697662E-1,0.E0,-8.697542675479E-1)); -#8368=VECTOR('',#8367,4.311496843946E-2); -#8369=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,3.099999713898E0)); -#8370=LINE('',#8369,#8368); -#8371=DIRECTION('',(-4.934850697662E-1,0.E0,8.697542675479E-1)); -#8372=VECTOR('',#8371,4.311496843946E-2); -#8373=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,3.062500286102E0)); -#8374=LINE('',#8373,#8372); -#8375=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#8376=VECTOR('',#8375,1.020154752811E-1); -#8377=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,3.006250286102E0)); -#8378=LINE('',#8377,#8376); -#8379=DIRECTION('',(-9.594586349813E-1,0.E0,2.818494771324E-1)); -#8380=VECTOR('',#8379,6.652690079599E-2); -#8381=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,2.987499713898E0)); -#8382=LINE('',#8381,#8380); -#8383=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8384=VECTOR('',#8383,1.063829660416E-1); -#8385=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,2.987499713898E0)); -#8386=LINE('',#8385,#8384); -#8387=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#8388=VECTOR('',#8387,6.652688649895E-2); -#8389=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,3.006250286102E0)); -#8390=LINE('',#8389,#8388); -#8391=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#8392=VECTOR('',#8391,1.020154814968E-1); -#8393=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,3.062500286102E0)); -#8394=LINE('',#8393,#8392); -#8395=DIRECTION('',(-6.481200514639E-1,0.E0,-7.615381795356E-1)); -#8396=VECTOR('',#8395,9.848450926445E-2); -#8397=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,3.1375E0)); -#8398=LINE('',#8397,#8396); -#8399=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#8400=VECTOR('',#8399,9.613433123539E-2); -#8401=CARTESIAN_POINT('',(4.E0,1.5E0,3.231250286102E0)); -#8402=LINE('',#8401,#8400); -#8403=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8404=VECTOR('',#8403,4.499995708466E-1); -#8405=CARTESIAN_POINT('',(4.E0,1.5E0,3.681249856949E0)); -#8406=LINE('',#8405,#8404); -#8407=DIRECTION('',(1.E0,0.E0,0.E0)); -#8408=VECTOR('',#8407,1.E0); -#8409=CARTESIAN_POINT('',(3.E0,1.5E0,3.681249856949E0)); -#8410=LINE('',#8409,#8408); -#8411=DIRECTION('',(0.E0,0.E0,1.E0)); -#8412=VECTOR('',#8411,4.499995708466E-1); -#8413=CARTESIAN_POINT('',(3.E0,1.5E0,3.231250286102E0)); -#8414=LINE('',#8413,#8412); -#8415=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#8416=VECTOR('',#8415,9.613433082315E-2); -#8417=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,3.1375E0)); -#8418=LINE('',#8417,#8416); -#8419=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#8420=VECTOR('',#8419,9.848450564280E-2); -#8421=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,3.062500286102E0)); -#8422=LINE('',#8421,#8420); -#8423=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#8424=VECTOR('',#8423,1.020154752811E-1); -#8425=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,3.006250286102E0)); -#8426=LINE('',#8425,#8424); -#8427=DIRECTION('',(-9.594585993946E-1,0.E0,2.818495982749E-1)); -#8428=VECTOR('',#8427,6.652687220190E-2); -#8429=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,2.987499713898E0)); -#8430=LINE('',#8429,#8428); -#8431=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8432=VECTOR('',#8431,8.510643243790E-2); -#8433=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,2.987499713898E0)); -#8434=LINE('',#8433,#8432); -#8435=DIRECTION('',(-9.594585993946E-1,0.E0,-2.818495982749E-1)); -#8436=VECTOR('',#8435,6.652687220190E-2); -#8437=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,3.006250286102E0)); -#8438=LINE('',#8437,#8436); -#8439=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#8440=VECTOR('',#8439,1.020154752811E-1); -#8441=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,3.062500286102E0)); -#8442=LINE('',#8441,#8440); -#8443=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8444=VECTOR('',#8443,3.562501430511E-1); -#8445=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,3.568749856949E0)); -#8446=LINE('',#8445,#8444); -#8447=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8448=VECTOR('',#8447,2.978723645210E-1); -#8449=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,3.568749856949E0)); -#8450=LINE('',#8449,#8448); -#8451=DIRECTION('',(0.E0,0.E0,1.E0)); -#8452=VECTOR('',#8451,3.562501430511E-1); -#8453=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,3.212499713898E0)); -#8454=LINE('',#8453,#8452); -#8455=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#8456=VECTOR('',#8455,6.013947055430E-2); -#8457=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,3.156249713898E0)); -#8458=LINE('',#8457,#8456); -#8459=DIRECTION('',(7.502531961943E-1,0.E0,6.611506194509E-1)); -#8460=VECTOR('',#8459,5.671843403331E-2); -#8461=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,3.118750286102E0)); -#8462=LINE('',#8461,#8460); -#8463=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#8464=VECTOR('',#8463,6.652687220190E-2); -#8465=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,3.099999713898E0)); -#8466=LINE('',#8465,#8464); -#8467=DIRECTION('',(1.E0,0.E0,0.E0)); -#8468=VECTOR('',#8467,4.255318641663E-2); -#8469=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,3.099999713898E0)); -#8470=LINE('',#8469,#8468); -#8471=DIRECTION('',(9.594586705679E-1,0.E0,-2.818493559900E-1)); -#8472=VECTOR('',#8471,6.652692939009E-2); -#8473=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,3.118750286102E0)); -#8474=LINE('',#8473,#8472); -#8475=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#8476=VECTOR('',#8475,5.671843403331E-2); -#8477=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,3.156249713898E0)); -#8478=LINE('',#8477,#8476); -#8479=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#8480=VECTOR('',#8479,6.013947055430E-2); -#8481=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,3.212499713898E0)); -#8482=LINE('',#8481,#8480); -#8483=DIRECTION('',(1.E0,0.E0,0.E0)); -#8484=VECTOR('',#8483,6.382977962494E-2); -#8485=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,3.099999713898E0)); -#8486=LINE('',#8485,#8484); -#8487=DIRECTION('',(9.594586349813E-1,0.E0,-2.818494771324E-1)); -#8488=VECTOR('',#8487,6.652690079599E-2); -#8489=CARTESIAN_POINT('',(3.617021262646E0,1.5E0,3.118750286102E0)); -#8490=LINE('',#8489,#8488); -#8491=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#8492=VECTOR('',#8491,5.671843403331E-2); -#8493=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,3.156249713898E0)); -#8494=LINE('',#8493,#8492); -#8495=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#8496=VECTOR('',#8495,6.013947055430E-2); -#8497=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,3.212499713898E0)); -#8498=LINE('',#8497,#8496); -#8499=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8500=VECTOR('',#8499,3.562501430511E-1); -#8501=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,3.568749856949E0)); -#8502=LINE('',#8501,#8500); -#8503=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8504=VECTOR('',#8503,3.191489428282E-1); -#8505=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,3.568749856949E0)); -#8506=LINE('',#8505,#8504); -#8507=DIRECTION('',(0.E0,0.E0,1.E0)); -#8508=VECTOR('',#8507,3.562501430511E-1); -#8509=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,3.212499713898E0)); -#8510=LINE('',#8509,#8508); -#8511=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#8512=VECTOR('',#8511,6.013947055430E-2); -#8513=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,3.156249713898E0)); -#8514=LINE('',#8513,#8512); -#8515=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#8516=VECTOR('',#8515,5.671844521296E-2); -#8517=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,3.118750286102E0)); -#8518=LINE('',#8517,#8516); -#8519=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#8520=VECTOR('',#8519,6.652687220190E-2); -#8521=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,3.099999713898E0)); -#8522=LINE('',#8521,#8520); -#8523=DIRECTION('',(0.E0,0.E0,1.E0)); -#8524=VECTOR('',#8523,7.125002861023E-1); -#8525=CARTESIAN_POINT('',(3.E0,1.5E0,2.125E0)); -#8526=LINE('',#8525,#8524); -#8527=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8528=VECTOR('',#8527,1.063829660416E-1); -#8529=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.125E0)); -#8530=LINE('',#8529,#8528); -#8531=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8532=VECTOR('',#8531,2.999997138977E-1); -#8533=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.424999713898E0)); -#8534=LINE('',#8533,#8532); -#8535=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8536=VECTOR('',#8535,8.936170339584E-1); -#8537=CARTESIAN_POINT('',(4.E0,1.5E0,2.424999713898E0)); -#8538=LINE('',#8537,#8536); -#8539=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8540=VECTOR('',#8539,1.125E-1); -#8541=CARTESIAN_POINT('',(4.E0,1.5E0,2.537499713898E0)); -#8542=LINE('',#8541,#8540); -#8543=DIRECTION('',(1.E0,0.E0,0.E0)); -#8544=VECTOR('',#8543,8.936170339584E-1); -#8545=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.537499713898E0)); -#8546=LINE('',#8545,#8544); -#8547=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8548=VECTOR('',#8547,3.000005722046E-1); -#8549=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.837500286102E0)); -#8550=LINE('',#8549,#8548); -#8551=DIRECTION('',(1.E0,0.E0,0.E0)); -#8552=VECTOR('',#8551,1.063829660416E-1); -#8553=CARTESIAN_POINT('',(3.E0,1.5E0,2.837500286102E0)); -#8554=LINE('',#8553,#8552); -#8555=DIRECTION('',(4.934850697662E-1,0.E0,8.697542675479E-1)); -#8556=VECTOR('',#8555,4.311496843946E-2); -#8557=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,1.825000286102E0)); -#8558=LINE('',#8557,#8556); -#8559=DIRECTION('',(4.934850697662E-1,0.E0,-8.697542675479E-1)); -#8560=VECTOR('',#8559,4.311496843946E-2); -#8561=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,1.862499713898E0)); -#8562=LINE('',#8561,#8560); -#8563=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#8564=VECTOR('',#8563,8.507821852254E-2); -#8565=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.918749713898E0)); -#8566=LINE('',#8565,#8564); -#8567=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#8568=VECTOR('',#8567,9.300196855221E-2); -#8569=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,1.95625E0)); -#8570=LINE('',#8569,#8568); -#8571=DIRECTION('',(1.E0,0.E0,0.E0)); -#8572=VECTOR('',#8571,6.382977962494E-2); -#8573=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.95625E0)); -#8574=LINE('',#8573,#8572); -#8575=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#8576=VECTOR('',#8575,1.127990230605E-1); -#8577=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.918749713898E0)); -#8578=LINE('',#8577,#8576); -#8579=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#8580=VECTOR('',#8579,8.507821852254E-2); -#8581=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,1.862499713898E0)); -#8582=LINE('',#8581,#8580); -#8583=DIRECTION('',(5.627932782715E-1,0.E0,8.265976808173E-1)); -#8584=VECTOR('',#8583,1.134160305201E-1); -#8585=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.768750286102E0)); -#8586=LINE('',#8585,#8584); -#8587=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#8588=VECTOR('',#8587,9.613433082315E-2); -#8589=CARTESIAN_POINT('',(3.E0,1.5E0,1.675E0)); -#8590=LINE('',#8589,#8588); -#8591=DIRECTION('',(0.E0,0.E0,1.E0)); -#8592=VECTOR('',#8591,7.499971389771E-2); -#8593=CARTESIAN_POINT('',(3.E0,1.5E0,1.600000286102E0)); -#8594=LINE('',#8593,#8592); -#8595=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#8596=VECTOR('',#8595,9.613433082315E-2); -#8597=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.50625E0)); -#8598=LINE('',#8597,#8596); -#8599=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#8600=VECTOR('',#8599,1.134167399956E-1); -#8601=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,1.412499713898E0)); -#8602=LINE('',#8601,#8600); -#8603=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#8604=VECTOR('',#8603,8.507821852254E-2); -#8605=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.356249713898E0)); -#8606=LINE('',#8605,#8604); -#8607=DIRECTION('',(-9.431224834518E-1,0.E0,3.324454559889E-1)); -#8608=VECTOR('',#8607,1.127987377173E-1); -#8609=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.318750286102E0)); -#8610=LINE('',#8609,#8608); -#8611=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8612=VECTOR('',#8611,6.382977962494E-2); -#8613=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,1.318750286102E0)); -#8614=LINE('',#8613,#8612); -#8615=DIRECTION('',(-9.151063236759E-1,0.E0,-4.032126193069E-1)); -#8616=VECTOR('',#8615,9.300162246873E-2); -#8617=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.356249713898E0)); -#8618=LINE('',#8617,#8616); -#8619=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#8620=VECTOR('',#8619,8.507821852254E-2); -#8621=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,1.412499713898E0)); -#8622=LINE('',#8621,#8620); -#8623=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#8624=VECTOR('',#8623,4.311571495761E-2); -#8625=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,1.45E0)); -#8626=LINE('',#8625,#8624); -#8627=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#8628=VECTOR('',#8627,4.311571495761E-2); -#8629=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,1.412499713898E0)); -#8630=LINE('',#8629,#8628); -#8631=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#8632=VECTOR('',#8631,9.848450564280E-2); -#8633=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,1.3375E0)); -#8634=LINE('',#8633,#8632); -#8635=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#8636=VECTOR('',#8635,1.127989949533E-1); -#8637=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.299999713898E0)); -#8638=LINE('',#8637,#8636); -#8639=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8640=VECTOR('',#8639,6.382977962494E-2); -#8641=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.299999713898E0)); -#8642=LINE('',#8641,#8640); -#8643=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#8644=VECTOR('',#8643,1.127989808997E-1); -#8645=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.3375E0)); -#8646=LINE('',#8645,#8644); -#8647=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#8648=VECTOR('',#8647,8.507822411232E-2); -#8649=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,1.39375E0)); -#8650=LINE('',#8649,#8648); -#8651=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#8652=VECTOR('',#8651,1.134167431404E-1); -#8653=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,1.487500286102E0)); -#8654=LINE('',#8653,#8652); -#8655=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#8656=VECTOR('',#8655,9.613349421393E-2); -#8657=CARTESIAN_POINT('',(4.E0,1.5E0,1.581249713898E0)); -#8658=LINE('',#8657,#8656); -#8659=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8660=VECTOR('',#8659,1.125E-1); -#8661=CARTESIAN_POINT('',(4.E0,1.5E0,1.693749713898E0)); -#8662=LINE('',#8661,#8660); -#8663=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#8664=VECTOR('',#8663,9.613433123539E-2); -#8665=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,1.7875E0)); -#8666=LINE('',#8665,#8664); -#8667=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#8668=VECTOR('',#8667,1.134167431404E-1); -#8669=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,1.881250286102E0)); -#8670=LINE('',#8669,#8668); -#8671=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#8672=VECTOR('',#8671,8.507822411232E-2); -#8673=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.937500286102E0)); -#8674=LINE('',#8673,#8672); -#8675=DIRECTION('',(9.431224396514E-1,0.E0,-3.324455802473E-1)); -#8676=VECTOR('',#8675,1.127986955565E-1); -#8677=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.974999713898E0)); -#8678=LINE('',#8677,#8676); -#8679=DIRECTION('',(1.E0,0.E0,0.E0)); -#8680=VECTOR('',#8679,6.382977962494E-2); -#8681=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.974999713898E0)); -#8682=LINE('',#8681,#8680); -#8683=DIRECTION('',(9.431224542516E-1,0.E0,3.324455388278E-1)); -#8684=VECTOR('',#8683,1.127987096101E-1); -#8685=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,1.937500286102E0)); -#8686=LINE('',#8685,#8684); -#8687=DIRECTION('',(6.481157170580E-1,0.E0,7.615418683844E-1)); -#8688=VECTOR('',#8687,9.848515927785E-2); -#8689=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,1.862499713898E0)); -#8690=LINE('',#8689,#8688); -#8691=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#8692=VECTOR('',#8691,7.795928747295E-2); -#8693=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.675E0)); -#8694=LINE('',#8693,#8692); -#8695=DIRECTION('',(0.E0,0.E0,1.E0)); -#8696=VECTOR('',#8695,7.499971389771E-2); -#8697=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.600000286102E0)); -#8698=LINE('',#8697,#8696); -#8699=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#8700=VECTOR('',#8699,7.796011319622E-2); -#8701=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,1.524999713898E0)); -#8702=LINE('',#8701,#8700); -#8703=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#8704=VECTOR('',#8703,8.623068339603E-2); -#8705=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.45E0)); -#8706=LINE('',#8705,#8704); -#8707=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#8708=VECTOR('',#8707,1.020154877124E-1); -#8709=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.39375E0)); -#8710=LINE('',#8709,#8708); -#8711=DIRECTION('',(1.E0,0.E0,0.E0)); -#8712=VECTOR('',#8711,6.382977962494E-2); -#8713=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.39375E0)); -#8714=LINE('',#8713,#8712); -#8715=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#8716=VECTOR('',#8715,1.020155001437E-1); -#8717=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,1.45E0)); -#8718=LINE('',#8717,#8716); -#8719=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#8720=VECTOR('',#8719,8.623068339603E-2); -#8721=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,1.524999713898E0)); -#8722=LINE('',#8721,#8720); -#8723=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#8724=VECTOR('',#8723,7.796011319622E-2); -#8725=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.600000286102E0)); -#8726=LINE('',#8725,#8724); -#8727=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8728=VECTOR('',#8727,7.499971389771E-2); -#8729=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.675E0)); -#8730=LINE('',#8729,#8728); -#8731=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#8732=VECTOR('',#8731,7.795928747295E-2); -#8733=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,1.749999713898E0)); -#8734=LINE('',#8733,#8732); -#8735=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#8736=VECTOR('',#8735,8.623142991522E-2); -#8737=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,1.825000286102E0)); -#8738=LINE('',#8737,#8736); -#8739=DIRECTION('',(-8.342497220098E-1,0.E0,-5.513867982882E-1)); -#8740=VECTOR('',#8739,1.020155001437E-1); -#8741=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.881250286102E0)); -#8742=LINE('',#8741,#8740); -#8743=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8744=VECTOR('',#8743,6.382977962494E-2); -#8745=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.881250286102E0)); -#8746=LINE('',#8745,#8744); -#8747=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654785E-1)); -#8748=VECTOR('',#8747,1.020154877124E-1); -#8749=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.825000286102E0)); -#8750=LINE('',#8749,#8748); -#8751=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#8752=VECTOR('',#8751,8.623142991522E-2); -#8753=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,1.749999713898E0)); -#8754=LINE('',#8753,#8752); -#8755=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#8756=VECTOR('',#8755,7.796011319622E-2); -#8757=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,1.600000286102E0)); -#8758=LINE('',#8757,#8756); -#8759=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8760=VECTOR('',#8759,7.499971389771E-2); -#8761=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,1.675E0)); -#8762=LINE('',#8761,#8760); -#8763=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#8764=VECTOR('',#8763,7.795928747295E-2); -#8765=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.749999713898E0)); -#8766=LINE('',#8765,#8764); -#8767=DIRECTION('',(-6.481157170580E-1,0.E0,-7.615418683844E-1)); -#8768=VECTOR('',#8767,9.848515927785E-2); -#8769=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,1.825000286102E0)); -#8770=LINE('',#8769,#8768); -#8771=DIRECTION('',(-8.622147026148E-1,0.E0,-5.065429958009E-1)); -#8772=VECTOR('',#8771,7.403009834559E-2); -#8773=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.862499713898E0)); -#8774=LINE('',#8773,#8772); -#8775=DIRECTION('',(-1.E0,0.E0,0.E0)); -#8776=VECTOR('',#8775,4.255318641663E-2); -#8777=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,1.862499713898E0)); -#8778=LINE('',#8777,#8776); -#8779=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#8780=VECTOR('',#8779,7.403004695359E-2); -#8781=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,1.825000286102E0)); -#8782=LINE('',#8781,#8780); -#8783=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#8784=VECTOR('',#8783,9.848515927785E-2); -#8785=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,1.749999713898E0)); -#8786=LINE('',#8785,#8784); -#8787=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#8788=VECTOR('',#8787,7.795928747295E-2); -#8789=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,1.675E0)); -#8790=LINE('',#8789,#8788); -#8791=DIRECTION('',(0.E0,0.E0,1.E0)); -#8792=VECTOR('',#8791,7.499971389771E-2); -#8793=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,1.600000286102E0)); -#8794=LINE('',#8793,#8792); -#8795=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#8796=VECTOR('',#8795,7.796011319622E-2); -#8797=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,1.524999713898E0)); -#8798=LINE('',#8797,#8796); -#8799=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#8800=VECTOR('',#8799,9.848450564280E-2); -#8801=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,1.45E0)); -#8802=LINE('',#8801,#8800); -#8803=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#8804=VECTOR('',#8803,7.403048172694E-2); -#8805=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,1.412499713898E0)); -#8806=LINE('',#8805,#8804); -#8807=DIRECTION('',(1.E0,0.E0,0.E0)); -#8808=VECTOR('',#8807,4.255318641663E-2); -#8809=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.412499713898E0)); -#8810=LINE('',#8809,#8808); -#8811=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#8812=VECTOR('',#8811,7.403053311863E-2); -#8813=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,1.45E0)); -#8814=LINE('',#8813,#8812); -#8815=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#8816=VECTOR('',#8815,9.848450564280E-2); -#8817=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.524999713898E0)); -#8818=LINE('',#8817,#8816); -#8819=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#8820=VECTOR('',#8819,7.403048172694E-2); -#8821=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.312502861023E-1)); -#8822=LINE('',#8821,#8820); -#8823=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#8824=VECTOR('',#8823,7.053252305355E-2); -#8825=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,5.875002861023E-1)); -#8826=LINE('',#8825,#8824); -#8827=DIRECTION('',(-4.934808465838E-1,0.E0,-8.697566637025E-1)); -#8828=VECTOR('',#8827,8.623068615357E-2); -#8829=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,6.625E-1)); -#8830=LINE('',#8829,#8828); -#8831=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#8832=VECTOR('',#8831,7.795928798130E-2); -#8833=CARTESIAN_POINT('',(4.E0,1.5E0,7.374997138977E-1)); -#8834=LINE('',#8833,#8832); -#8835=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8836=VECTOR('',#8835,1.500002861023E-1); -#8837=CARTESIAN_POINT('',(4.E0,1.5E0,8.875E-1)); -#8838=LINE('',#8837,#8836); -#8839=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#8840=VECTOR('',#8839,7.795928798130E-2); -#8841=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.624997138977E-1)); -#8842=LINE('',#8841,#8840); -#8843=DIRECTION('',(4.934765744419E-1,0.E0,-8.697590876082E-1)); -#8844=VECTOR('',#8843,8.623143267274E-2); -#8845=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,1.037500286102E0)); -#8846=LINE('',#8845,#8844); -#8847=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#8848=VECTOR('',#8847,7.053252305355E-2); -#8849=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.093750286102E0)); -#8850=LINE('',#8849,#8848); -#8851=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#8852=VECTOR('',#8851,7.403004695359E-2); -#8853=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.131249713898E0)); -#8854=LINE('',#8853,#8852); -#8855=DIRECTION('',(9.594586171880E-1,0.E0,-2.818495377036E-1)); -#8856=VECTOR('',#8855,6.652688649895E-2); -#8857=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,1.150000286102E0)); -#8858=LINE('',#8857,#8856); -#8859=DIRECTION('',(0.E0,0.E0,1.E0)); -#8860=VECTOR('',#8859,9.375028610230E-2); -#8861=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,1.05625E0)); -#8862=LINE('',#8861,#8860); -#8863=DIRECTION('',(-9.151063236759E-1,0.E0,4.032126193069E-1)); -#8864=VECTOR('',#8863,4.650081123436E-2); -#8865=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,1.037500286102E0)); -#8866=LINE('',#8865,#8864); -#8867=DIRECTION('',(-7.502458047514E-1,0.E0,6.611590069362E-1)); -#8868=VECTOR('',#8867,5.671901268663E-2); -#8869=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.E0)); -#8870=LINE('',#8869,#8868); -#8871=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#8872=VECTOR('',#8871,4.311571495761E-2); -#8873=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.624997138977E-1)); -#8874=LINE('',#8873,#8872); -#8875=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#8876=VECTOR('',#8875,9.613349380169E-2); -#8877=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,8.687502861023E-1)); -#8878=LINE('',#8877,#8876); -#8879=DIRECTION('',(0.E0,0.E0,1.E0)); -#8880=VECTOR('',#8879,1.125E-1); -#8881=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,7.562502861023E-1)); -#8882=LINE('',#8881,#8880); -#8883=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#8884=VECTOR('',#8883,9.613433082315E-2); -#8885=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,6.625E-1)); -#8886=LINE('',#8885,#8884); -#8887=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#8888=VECTOR('',#8887,4.311571495761E-2); -#8889=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,6.249997138977E-1)); -#8890=LINE('',#8889,#8888); -#8891=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#8892=VECTOR('',#8891,5.671844521296E-2); -#8893=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,5.875002861023E-1)); -#8894=LINE('',#8893,#8892); -#8895=DIRECTION('',(9.150995129590E-1,0.E0,4.032280761334E-1)); -#8896=VECTOR('',#8895,4.650115732116E-2); -#8897=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,5.687497138977E-1)); -#8898=LINE('',#8897,#8896); -#8899=DIRECTION('',(1.E0,0.E0,0.E0)); -#8900=VECTOR('',#8899,8.510637283325E-2); -#8901=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.687497138977E-1)); -#8902=LINE('',#8901,#8900); -#8903=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#8904=VECTOR('',#8903,9.300199582440E-2); -#8905=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,6.0625E-1)); -#8906=LINE('',#8905,#8904); -#8907=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#8908=VECTOR('',#8907,7.053251855852E-2); -#8909=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,6.625E-1)); -#8910=LINE('',#8909,#8908); -#8911=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#8912=VECTOR('',#8911,1.144942942620E-1); -#8913=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,7.75E-1)); -#8914=LINE('',#8913,#8912); -#8915=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8916=VECTOR('',#8915,7.499971389770E-2); -#8917=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,8.499997138977E-1)); -#8918=LINE('',#8917,#8916); -#8919=DIRECTION('',(1.E0,0.E0,0.E0)); -#8920=VECTOR('',#8919,8.510637283325E-2); -#8921=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,8.499997138977E-1)); -#8922=LINE('',#8921,#8920); -#8923=DIRECTION('',(0.E0,0.E0,1.E0)); -#8924=VECTOR('',#8923,7.499971389770E-2); -#8925=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,7.75E-1)); -#8926=LINE('',#8925,#8924); -#8927=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#8928=VECTOR('',#8927,1.202789411086E-1); -#8929=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,6.625E-1)); -#8930=LINE('',#8929,#8928); -#8931=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#8932=VECTOR('',#8931,5.671900150710E-2); -#8933=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,6.249997138977E-1)); -#8934=LINE('',#8933,#8932); -#8935=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#8936=VECTOR('',#8935,9.300162246873E-2); -#8937=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,5.875002861023E-1)); -#8938=LINE('',#8937,#8936); -#8939=DIRECTION('',(1.E0,0.E0,0.E0)); -#8940=VECTOR('',#8939,4.255324602127E-2); -#8941=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,5.875002861023E-1)); -#8942=LINE('',#8941,#8940); -#8943=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#8944=VECTOR('',#8943,7.403004695359E-2); -#8945=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,6.249997138977E-1)); -#8946=LINE('',#8945,#8944); -#8947=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#8948=VECTOR('',#8947,7.053251855852E-2); -#8949=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,6.812497138977E-1)); -#8950=LINE('',#8949,#8948); -#8951=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#8952=VECTOR('',#8951,9.613433082315E-2); -#8953=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,7.75E-1)); -#8954=LINE('',#8953,#8952); -#8955=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8956=VECTOR('',#8955,7.499971389770E-2); -#8957=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,8.499997138977E-1)); -#8958=LINE('',#8957,#8956); -#8959=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#8960=VECTOR('',#8959,9.613433082315E-2); -#8961=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.4375E-1)); -#8962=LINE('',#8961,#8960); -#8963=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865771E-1)); -#8964=VECTOR('',#8963,7.053251855852E-2); -#8965=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,1.E0)); -#8966=LINE('',#8965,#8964); -#8967=DIRECTION('',(-8.622094323306E-1,0.E0,-5.065519665348E-1)); -#8968=VECTOR('',#8967,7.403048172694E-2); -#8969=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,1.037500286102E0)); -#8970=LINE('',#8969,#8968); -#8971=DIRECTION('',(0.E0,0.E0,-1.E0)); -#8972=VECTOR('',#8971,9.374942779541E-2); -#8973=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,1.131249713898E0)); -#8974=LINE('',#8973,#8972); -#8975=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#8976=VECTOR('',#8975,8.714726885037E-2); -#8977=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.1125E0)); -#8978=LINE('',#8977,#8976); -#8979=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#8980=VECTOR('',#8979,1.134374355386E-1); -#8981=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,1.037500286102E0)); -#8982=LINE('',#8981,#8980); -#8983=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#8984=VECTOR('',#8983,8.623142991522E-2); -#8985=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.624997138977E-1)); -#8986=LINE('',#8985,#8984); -#8987=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#8988=VECTOR('',#8987,1.329630806532E-1); -#8989=CARTESIAN_POINT('',(3.E0,1.5E0,8.3125E-1)); -#8990=LINE('',#8989,#8988); -#8991=DIRECTION('',(0.E0,0.E0,1.E0)); -#8992=VECTOR('',#8991,3.750028610230E-2); -#8993=CARTESIAN_POINT('',(3.E0,1.5E0,7.937497138977E-1)); -#8994=LINE('',#8993,#8992); -#8995=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#8996=VECTOR('',#8995,1.329630806532E-1); -#8997=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,6.625E-1)); -#8998=LINE('',#8997,#8996); -#8999=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#9000=VECTOR('',#8999,8.623068339603E-2); -#9001=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,5.875002861023E-1)); -#9002=LINE('',#9001,#9000); -#9003=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#9004=VECTOR('',#9003,1.134380030142E-1); -#9005=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,5.124997138977E-1)); -#9006=LINE('',#9005,#9004); -#9007=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#9008=VECTOR('',#9007,8.714726885037E-2); -#9009=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,4.9375E-1)); -#9010=LINE('',#9009,#9008); -#9011=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9012=VECTOR('',#9011,4.255324602127E-2); -#9013=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,4.9375E-1)); -#9014=LINE('',#9013,#9012); -#9015=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#9016=VECTOR('',#9015,8.714726885037E-2); -#9017=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.124997138977E-1)); -#9018=LINE('',#9017,#9016); -#9019=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#9020=VECTOR('',#9019,7.403048172694E-2); -#9021=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.5E-1)); -#9022=LINE('',#9021,#9020); -#9023=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#9024=VECTOR('',#9023,9.848450564280E-2); -#9025=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.249997138977E-1)); -#9026=LINE('',#9025,#9024); -#9027=DIRECTION('',(-4.133183693567E-1,0.E0,9.105865832266E-1)); -#9028=VECTOR('',#9027,1.029549847563E-1); -#9029=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.312502861023E-1)); -#9030=LINE('',#9029,#9028); -#9031=DIRECTION('',(-8.622094323305E-1,0.E0,5.065519665348E-1)); -#9032=VECTOR('',#9031,7.403048172694E-2); -#9033=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,4.9375E-1)); -#9034=LINE('',#9033,#9032); -#9035=DIRECTION('',(-9.765810832111E-1,0.E0,2.151496872277E-1)); -#9036=VECTOR('',#9035,8.714729795475E-2); -#9037=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.750002861023E-1)); -#9038=LINE('',#9037,#9036); -#9039=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9040=VECTOR('',#9039,8.510637283325E-2); -#9041=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.750002861023E-1)); -#9042=LINE('',#9041,#9040); -#9043=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#9044=VECTOR('',#9043,6.652664459064E-2); -#9045=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,4.9375E-1)); -#9046=LINE('',#9045,#9044); -#9047=DIRECTION('',(1.E0,0.E0,0.E0)); -#9048=VECTOR('',#9047,1.063829809427E-1); -#9049=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,3.25E-1)); -#9050=LINE('',#9049,#9048); -#9051=DIRECTION('',(7.117179927714E-1,0.E0,7.024653007554E-1)); -#9052=VECTOR('',#9051,7.473674690168E-1); -#9053=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,-1.999997138977E-1)); -#9054=LINE('',#9053,#9052); -#9055=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#9056=VECTOR('',#9055,9.300196855221E-2); -#9057=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,-2.375E-1)); -#9058=LINE('',#9057,#9056); -#9059=DIRECTION('',(1.E0,0.E0,0.E0)); -#9060=VECTOR('',#9059,4.255324602127E-2); -#9061=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,-2.375E-1)); -#9062=LINE('',#9061,#9060); -#9063=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#9064=VECTOR('',#9063,7.403048172694E-2); -#9065=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,-1.999997138977E-1)); -#9066=LINE('',#9065,#9064); -#9067=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865770E-1)); -#9068=VECTOR('',#9067,7.053251855852E-2); -#9069=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,-1.437497138977E-1)); -#9070=LINE('',#9069,#9068); -#9071=DIRECTION('',(2.213234156683E-1,0.E0,-9.752004643543E-1)); -#9072=VECTOR('',#9071,9.613349380169E-2); -#9073=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,-5.000028610230E-2)); -#9074=LINE('',#9073,#9072); -#9075=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9076=VECTOR('',#9075,7.500057220459E-2); -#9077=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.500028610229E-2)); -#9078=LINE('',#9077,#9076); -#9079=DIRECTION('',(-2.213234156683E-1,0.E0,-9.752004643543E-1)); -#9080=VECTOR('',#9079,9.613349380169E-2); -#9081=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.187497138977E-1)); -#9082=LINE('',#9081,#9080); -#9083=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#9084=VECTOR('',#9083,7.053251855852E-2); -#9085=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,1.749997138977E-1)); -#9086=LINE('',#9085,#9084); -#9087=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#9088=VECTOR('',#9087,7.403048172694E-2); -#9089=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,2.125E-1)); -#9090=LINE('',#9089,#9088); -#9091=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9092=VECTOR('',#9091,9.375028610230E-2); -#9093=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,3.062502861023E-1)); -#9094=LINE('',#9093,#9092); -#9095=DIRECTION('',(9.765789979713E-1,0.E0,2.151591520746E-1)); -#9096=VECTOR('',#9095,8.714745351892E-2); -#9097=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,2.874997138977E-1)); -#9098=LINE('',#9097,#9096); -#9099=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#9100=VECTOR('',#9099,1.134374355386E-1); -#9101=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,2.125E-1)); -#9102=LINE('',#9101,#9100); -#9103=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#9104=VECTOR('',#9103,8.623068339603E-2); -#9105=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.375002861023E-1)); -#9106=LINE('',#9105,#9104); -#9107=DIRECTION('',(1.600177848561E-1,0.E0,9.871141314609E-1)); -#9108=VECTOR('',#9107,1.329639279E-1); -#9109=CARTESIAN_POINT('',(3.E0,1.5E0,6.249713897704E-3)); -#9110=LINE('',#9109,#9108); -#9111=DIRECTION('',(0.E0,0.E0,1.E0)); -#9112=VECTOR('',#9111,7.499971389771E-2); -#9113=CARTESIAN_POINT('',(3.E0,1.5E0,-6.875E-2)); -#9114=LINE('',#9113,#9112); -#9115=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#9116=VECTOR('',#9115,1.144942942620E-1); -#9117=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,-1.8125E-1)); -#9118=LINE('',#9117,#9116); -#9119=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#9120=VECTOR('',#9119,8.623068339603E-2); -#9121=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,-2.562497138977E-1)); -#9122=LINE('',#9121,#9120); -#9123=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#9124=VECTOR('',#9123,1.134380030142E-1); -#9125=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,-3.312502861023E-1)); -#9126=LINE('',#9125,#9124); -#9127=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#9128=VECTOR('',#9127,8.714726885037E-2); -#9129=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,-3.5E-1)); -#9130=LINE('',#9129,#9128); -#9131=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9132=VECTOR('',#9131,4.255324602127E-2); -#9133=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,-3.5E-1)); -#9134=LINE('',#9133,#9132); -#9135=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#9136=VECTOR('',#9135,8.714726885037E-2); -#9137=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,-3.312502861023E-1)); -#9138=LINE('',#9137,#9136); -#9139=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#9140=VECTOR('',#9139,7.403048172694E-2); -#9141=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,-2.9375E-1)); -#9142=LINE('',#9141,#9140); -#9143=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#9144=VECTOR('',#9143,6.624424131262E-1); -#9145=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.749997138977E-1)); -#9146=LINE('',#9145,#9144); -#9147=DIRECTION('',(0.E0,0.E0,1.E0)); -#9148=VECTOR('',#9147,5.249997138977E-1); -#9149=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,-3.5E-1)); -#9150=LINE('',#9149,#9148); -#9151=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9152=VECTOR('',#9151,1.063829809427E-1); -#9153=CARTESIAN_POINT('',(4.E0,1.5E0,-3.5E-1)); -#9154=LINE('',#9153,#9152); -#9155=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9156=VECTOR('',#9155,6.75E-1); -#9157=CARTESIAN_POINT('',(4.E0,1.5E0,3.25E-1)); -#9158=LINE('',#9157,#9156); -#9159=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9160=VECTOR('',#9159,1.E0); -#9161=CARTESIAN_POINT('',(5.75E0,1.5E0,1.03375E1)); -#9162=LINE('',#9161,#9160); -#9163=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9164=VECTOR('',#9163,1.125E-1); -#9165=CARTESIAN_POINT('',(5.75E0,1.5E0,1.045E1)); -#9166=LINE('',#9165,#9164); -#9167=DIRECTION('',(1.E0,0.E0,0.E0)); -#9168=VECTOR('',#9167,1.E0); -#9169=CARTESIAN_POINT('',(4.75E0,1.5E0,1.045E1)); -#9170=LINE('',#9169,#9168); -#9171=DIRECTION('',(0.E0,0.E0,1.E0)); -#9172=VECTOR('',#9171,1.125E-1); -#9173=CARTESIAN_POINT('',(4.75E0,1.5E0,1.03375E1)); -#9174=LINE('',#9173,#9172); -#9175=DIRECTION('',(0.E0,0.E0,1.E0)); -#9176=VECTOR('',#9175,1.124999463558E-1); -#9177=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,9.456250035763E0)); -#9178=LINE('',#9177,#9176); -#9179=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#9180=VECTOR('',#9179,1.080226756383E-1); -#9181=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.474999964237E0)); -#9182=LINE('',#9181,#9180); -#9183=DIRECTION('',(-7.502480643278E-1,0.E0,-6.611564428881E-1)); -#9184=VECTOR('',#9183,1.134376539313E-1); -#9185=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,9.55E0)); -#9186=LINE('',#9185,#9184); -#9187=DIRECTION('',(-4.934795115328E-1,0.E0,-8.697574211798E-1)); -#9188=VECTOR('',#9187,8.623091944059E-2); -#9189=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.624999982119E0)); -#9190=LINE('',#9189,#9188); -#9191=DIRECTION('',(-2.213221092673E-1,0.E0,-9.752007608434E-1)); -#9192=VECTOR('',#9191,9.613406966615E-2); -#9193=CARTESIAN_POINT('',(5.75E0,1.5E0,9.71875E0)); -#9194=LINE('',#9193,#9192); -#9195=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9196=VECTOR('',#9195,1.6875E-1); -#9197=CARTESIAN_POINT('',(5.75E0,1.5E0,9.8875E0)); -#9198=LINE('',#9197,#9196); -#9199=DIRECTION('',(2.213221092673E-1,0.E0,-9.752007608434E-1)); -#9200=VECTOR('',#9199,9.613406966615E-2); -#9201=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.981250017881E0)); -#9202=LINE('',#9201,#9200); -#9203=DIRECTION('',(4.934795115328E-1,0.E0,-8.697574211798E-1)); -#9204=VECTOR('',#9203,8.623091944058E-2); -#9205=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,1.005625E1)); -#9206=LINE('',#9205,#9204); -#9207=DIRECTION('',(7.502481816133E-1,0.E0,-6.611563097982E-1)); -#9208=VECTOR('',#9207,1.134376361977E-1); -#9209=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.013125000894E1)); -#9210=LINE('',#9209,#9208); -#9211=DIRECTION('',(9.151041149770E-1,0.E0,-4.032176319956E-1)); -#9212=VECTOR('',#9211,9.300186322138E-2); -#9213=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.016875E1)); -#9214=LINE('',#9213,#9212); -#9215=DIRECTION('',(9.848206972314E-1,0.E0,-1.735747513456E-1)); -#9216=VECTOR('',#9215,1.080226749302E-1); -#9217=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,1.018750000894E1)); -#9218=LINE('',#9217,#9216); -#9219=DIRECTION('',(1.E0,0.E0,0.E0)); -#9220=VECTOR('',#9219,3.191489279270E-1); -#9221=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,1.018750000894E1)); -#9222=LINE('',#9221,#9220); -#9223=DIRECTION('',(9.848207138555E-1,0.E0,1.735746570245E-1)); -#9224=VECTOR('',#9223,1.080227336301E-1); -#9225=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.016875E1)); -#9226=LINE('',#9225,#9224); -#9227=DIRECTION('',(9.151040889270E-1,0.E0,4.032176911162E-1)); -#9228=VECTOR('',#9227,9.300184958527E-2); -#9229=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.013125000894E1)); -#9230=LINE('',#9229,#9228); -#9231=DIRECTION('',(7.502481529028E-1,0.E0,6.611563423775E-1)); -#9232=VECTOR('',#9231,1.134376306079E-1); -#9233=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.005625E1)); -#9234=LINE('',#9233,#9232); -#9235=DIRECTION('',(4.934794625115E-1,0.E0,8.697574489933E-1)); -#9236=VECTOR('',#9235,8.623091668305E-2); -#9237=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.981250017881E0)); -#9238=LINE('',#9237,#9236); -#9239=DIRECTION('',(2.213220908409E-1,0.E0,9.752007650252E-1)); -#9240=VECTOR('',#9239,9.613406925390E-2); -#9241=CARTESIAN_POINT('',(4.75E0,1.5E0,9.8875E0)); -#9242=LINE('',#9241,#9240); -#9243=DIRECTION('',(0.E0,0.E0,1.E0)); -#9244=VECTOR('',#9243,1.6875E-1); -#9245=CARTESIAN_POINT('',(4.75E0,1.5E0,9.71875E0)); -#9246=LINE('',#9245,#9244); -#9247=DIRECTION('',(-2.213220908409E-1,0.E0,9.752007650252E-1)); -#9248=VECTOR('',#9247,9.613406925390E-2); -#9249=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.624999982119E0)); -#9250=LINE('',#9249,#9248); -#9251=DIRECTION('',(-4.934794625115E-1,0.E0,8.697574489933E-1)); -#9252=VECTOR('',#9251,8.623091668305E-2); -#9253=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,9.55E0)); -#9254=LINE('',#9253,#9252); -#9255=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#9256=VECTOR('',#9255,1.134376483415E-1); -#9257=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.474999964237E0)); -#9258=LINE('',#9257,#9256); -#9259=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#9260=VECTOR('',#9259,1.080227196632E-1); -#9261=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,9.456250035763E0)); -#9262=LINE('',#9261,#9260); -#9263=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9264=VECTOR('',#9263,1.124999463558E-1); -#9265=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,9.568749982119E0)); -#9266=LINE('',#9265,#9264); -#9267=DIRECTION('',(9.594608511063E-1,0.E0,-2.818419329952E-1)); -#9268=VECTOR('',#9267,6.652677819631E-2); -#9269=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,9.587500017881E0)); -#9270=LINE('',#9269,#9268); -#9271=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#9272=VECTOR('',#9271,7.053251855852E-2); -#9273=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.643750017881E0)); -#9274=LINE('',#9273,#9272); -#9275=DIRECTION('',(2.729183843844E-1,0.E0,-9.620371902713E-1)); -#9276=VECTOR('',#9275,7.795954551140E-2); -#9277=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.71875E0)); -#9278=LINE('',#9277,#9276); -#9279=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9280=VECTOR('',#9279,1.6875E-1); -#9281=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.8875E0)); -#9282=LINE('',#9281,#9280); -#9283=DIRECTION('',(-2.729183843844E-1,0.E0,-9.620371902713E-1)); -#9284=VECTOR('',#9283,7.795954551140E-2); -#9285=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.962499982119E0)); -#9286=LINE('',#9285,#9284); -#9287=DIRECTION('',(-6.033128318821E-1,0.E0,-7.975046249937E-1)); -#9288=VECTOR('',#9287,7.053253994926E-2); -#9289=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.001875000894E1)); -#9290=LINE('',#9289,#9288); -#9291=DIRECTION('',(-8.622113795709E-1,0.E0,-5.065486520942E-1)); -#9292=VECTOR('',#9291,7.403038366456E-2); -#9293=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.005625E1)); -#9294=LINE('',#9293,#9292); -#9295=DIRECTION('',(-9.765803560308E-1,0.E0,-2.151529879292E-1)); -#9296=VECTOR('',#9295,8.714733232927E-2); -#9297=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,1.007500000894E1)); -#9298=LINE('',#9297,#9296); -#9299=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9300=VECTOR('',#9299,3.191489279270E-1); -#9301=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,1.007500000894E1)); -#9302=LINE('',#9301,#9300); -#9303=DIRECTION('',(-9.765803560308E-1,0.E0,2.151529879292E-1)); -#9304=VECTOR('',#9303,8.714733232927E-2); -#9305=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.005625E1)); -#9306=LINE('',#9305,#9304); -#9307=DIRECTION('',(-8.622111729792E-1,0.E0,5.065490037399E-1)); -#9308=VECTOR('',#9307,7.403033227277E-2); -#9309=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,1.001875000894E1)); -#9310=LINE('',#9309,#9308); -#9311=DIRECTION('',(-6.033129662504E-1,0.E0,7.975045233440E-1)); -#9312=VECTOR('',#9311,7.053254893932E-2); -#9313=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.962499982119E0)); -#9314=LINE('',#9313,#9312); -#9315=DIRECTION('',(-2.729183843844E-1,0.E0,9.620371902713E-1)); -#9316=VECTOR('',#9315,7.795954551140E-2); -#9317=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.8875E0)); -#9318=LINE('',#9317,#9316); -#9319=DIRECTION('',(0.E0,0.E0,1.E0)); -#9320=VECTOR('',#9319,1.6875E-1); -#9321=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.71875E0)); -#9322=LINE('',#9321,#9320); -#9323=DIRECTION('',(2.729183843844E-1,0.E0,9.620371902713E-1)); -#9324=VECTOR('',#9323,7.795954551140E-2); -#9325=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.643750017881E0)); -#9326=LINE('',#9325,#9324); -#9327=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#9328=VECTOR('',#9327,7.053252754859E-2); -#9329=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,9.587500017881E0)); -#9330=LINE('',#9329,#9328); -#9331=DIRECTION('',(9.594607799365E-1,0.E0,2.818421752748E-1)); -#9332=VECTOR('',#9331,6.652672100798E-2); -#9333=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,9.568749982119E0)); -#9334=LINE('',#9333,#9332); -#9335=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9336=VECTOR('',#9335,1.E0); -#9337=CARTESIAN_POINT('',(5.75E0,1.5E0,9.193749964237E0)); -#9338=LINE('',#9337,#9336); -#9339=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9340=VECTOR('',#9339,1.125E-1); -#9341=CARTESIAN_POINT('',(5.75E0,1.5E0,9.306249964237E0)); -#9342=LINE('',#9341,#9340); -#9343=DIRECTION('',(1.E0,0.E0,0.E0)); -#9344=VECTOR('',#9343,1.E0); -#9345=CARTESIAN_POINT('',(4.75E0,1.5E0,9.306249964237E0)); -#9346=LINE('',#9345,#9344); -#9347=DIRECTION('',(0.E0,0.E0,1.E0)); -#9348=VECTOR('',#9347,1.125E-1); -#9349=CARTESIAN_POINT('',(4.75E0,1.5E0,9.193749964237E0)); -#9350=LINE('',#9349,#9348); -#9351=DIRECTION('',(0.E0,0.E0,1.E0)); -#9352=VECTOR('',#9351,4.5E-1); -#9353=CARTESIAN_POINT('',(4.75E0,1.5E0,8.59375E0)); -#9354=LINE('',#9353,#9352); -#9355=DIRECTION('',(-2.213219704028E-1,0.E0,9.752007923587E-1)); -#9356=VECTOR('',#9355,9.613412156775E-2); -#9357=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,8.499999928474E0)); -#9358=LINE('',#9357,#9356); -#9359=DIRECTION('',(-4.934797295212E-1,0.E0,8.697572974984E-1)); -#9360=VECTOR('',#9359,8.623087002563E-2); -#9361=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,8.425E0)); -#9362=LINE('',#9361,#9360); -#9363=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#9364=VECTOR('',#9363,1.134375774071E-1); -#9365=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,8.350000071526E0)); -#9366=LINE('',#9365,#9364); -#9367=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#9368=VECTOR('',#9367,9.300188203072E-2); -#9369=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,8.3125E0)); -#9370=LINE('',#9369,#9368); -#9371=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#9372=VECTOR('',#9371,1.080227196632E-1); -#9373=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,8.293750071526E0)); -#9374=LINE('',#9373,#9372); -#9375=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9376=VECTOR('',#9375,3.191489279270E-1); -#9377=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,8.293750071526E0)); -#9378=LINE('',#9377,#9376); -#9379=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#9380=VECTOR('',#9379,1.080226609633E-1); -#9381=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,8.3125E0)); -#9382=LINE('',#9381,#9380); -#9383=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#9384=VECTOR('',#9383,9.300189566683E-2); -#9385=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,8.350000071526E0)); -#9386=LINE('',#9385,#9384); -#9387=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#9388=VECTOR('',#9387,1.134375829969E-1); -#9389=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,8.425E0)); -#9390=LINE('',#9389,#9388); -#9391=DIRECTION('',(-4.934797785425E-1,0.E0,-8.697572696849E-1)); -#9392=VECTOR('',#9391,8.623087278316E-2); -#9393=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,8.499999928474E0)); -#9394=LINE('',#9393,#9392); -#9395=DIRECTION('',(-2.213219888292E-1,0.E0,-9.752007881768E-1)); -#9396=VECTOR('',#9395,9.613412197999E-2); -#9397=CARTESIAN_POINT('',(5.75E0,1.5E0,8.59375E0)); -#9398=LINE('',#9397,#9396); -#9399=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9400=VECTOR('',#9399,4.5E-1); -#9401=CARTESIAN_POINT('',(5.75E0,1.5E0,9.04375E0)); -#9402=LINE('',#9401,#9400); -#9403=DIRECTION('',(1.E0,0.E0,0.E0)); -#9404=VECTOR('',#9403,1.E0); -#9405=CARTESIAN_POINT('',(4.75E0,1.5E0,9.04375E0)); -#9406=LINE('',#9405,#9404); -#9407=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9408=VECTOR('',#9407,3.375E-1); -#9409=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,8.93125E0)); -#9410=LINE('',#9409,#9408); -#9411=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9412=VECTOR('',#9411,7.446808665991E-1); -#9413=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,8.93125E0)); -#9414=LINE('',#9413,#9412); -#9415=DIRECTION('',(0.E0,0.E0,1.E0)); -#9416=VECTOR('',#9415,3.375E-1); -#9417=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,8.59375E0)); -#9418=LINE('',#9417,#9416); -#9419=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#9420=VECTOR('',#9419,7.795949390370E-2); -#9421=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,8.518750071526E0)); -#9422=LINE('',#9421,#9420); -#9423=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#9424=VECTOR('',#9423,7.053252754859E-2); -#9425=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,8.462500071526E0)); -#9426=LINE('',#9425,#9424); -#9427=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117767E-1)); -#9428=VECTOR('',#9427,7.403037303291E-2); -#9429=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,8.425E0)); -#9430=LINE('',#9429,#9428); -#9431=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#9432=VECTOR('',#9431,8.714731501675E-2); -#9433=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,8.406250071526E0)); -#9434=LINE('',#9433,#9432); -#9435=DIRECTION('',(1.E0,0.E0,0.E0)); -#9436=VECTOR('',#9435,3.191489279270E-1); -#9437=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,8.406250071526E0)); -#9438=LINE('',#9437,#9436); -#9439=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#9440=VECTOR('',#9439,8.714731501675E-2); -#9441=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,8.425E0)); -#9442=LINE('',#9441,#9440); -#9443=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#9444=VECTOR('',#9443,7.403042442468E-2); -#9445=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,8.462500071526E0)); -#9446=LINE('',#9445,#9444); -#9447=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#9448=VECTOR('',#9447,7.053251855852E-2); -#9449=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,8.518750071526E0)); -#9450=LINE('',#9449,#9448); -#9451=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#9452=VECTOR('',#9451,7.795949390370E-2); -#9453=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,8.59375E0)); -#9454=LINE('',#9453,#9452); -#9455=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9456=VECTOR('',#9455,1.063829809427E-1); -#9457=CARTESIAN_POINT('',(5.75E0,1.5E0,8.049999928474E0)); -#9458=LINE('',#9457,#9456); -#9459=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9460=VECTOR('',#9459,9.375007152557E-2); -#9461=CARTESIAN_POINT('',(5.75E0,1.5E0,8.14375E0)); -#9462=LINE('',#9461,#9460); -#9463=DIRECTION('',(1.E0,0.E0,0.E0)); -#9464=VECTOR('',#9463,1.063829809427E-1); -#9465=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.14375E0)); -#9466=LINE('',#9465,#9464); -#9467=DIRECTION('',(0.E0,0.E0,1.E0)); -#9468=VECTOR('',#9467,9.375007152557E-2); -#9469=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.049999928474E0)); -#9470=LINE('',#9469,#9468); -#9471=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9472=VECTOR('',#9471,1.063829660416E-1); -#9473=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,8.049999928474E0)); -#9474=LINE('',#9473,#9472); -#9475=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9476=VECTOR('',#9475,9.375007152557E-2); -#9477=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,8.14375E0)); -#9478=LINE('',#9477,#9476); -#9479=DIRECTION('',(1.E0,0.E0,0.E0)); -#9480=VECTOR('',#9479,1.063829660416E-1); -#9481=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,8.14375E0)); -#9482=LINE('',#9481,#9480); -#9483=DIRECTION('',(0.E0,0.E0,1.E0)); -#9484=VECTOR('',#9483,9.375007152557E-2); -#9485=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,8.049999928474E0)); -#9486=LINE('',#9485,#9484); -#9487=DIRECTION('',(7.872280489029E-1,0.E0,6.166619811700E-1)); -#9488=VECTOR('',#9487,7.297352743333E-1); -#9489=CARTESIAN_POINT('',(4.75E0,1.5E0,7.450000071526E0)); -#9490=LINE('',#9489,#9488); -#9491=DIRECTION('',(0.E0,0.E0,1.E0)); -#9492=VECTOR('',#9491,1.125E-1); -#9493=CARTESIAN_POINT('',(4.75E0,1.5E0,7.337500071526E0)); -#9494=LINE('',#9493,#9492); -#9495=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9496=VECTOR('',#9495,5.744680762291E-1); -#9497=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.337500071526E0)); -#9498=LINE('',#9497,#9496); -#9499=DIRECTION('',(0.E0,0.E0,1.E0)); -#9500=VECTOR('',#9499,1.875001430511E-1); -#9501=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.149999928474E0)); -#9502=LINE('',#9501,#9500); -#9503=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9504=VECTOR('',#9503,1.276595890522E-1); -#9505=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.149999928474E0)); -#9506=LINE('',#9505,#9504); -#9507=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9508=VECTOR('',#9507,1.875001430511E-1); -#9509=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.337500071526E0)); -#9510=LINE('',#9509,#9508); -#9511=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9512=VECTOR('',#9511,2.978723347187E-1); -#9513=CARTESIAN_POINT('',(5.75E0,1.5E0,7.337500071526E0)); -#9514=LINE('',#9513,#9512); -#9515=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9516=VECTOR('',#9515,1.125E-1); -#9517=CARTESIAN_POINT('',(5.75E0,1.5E0,7.450000071526E0)); -#9518=LINE('',#9517,#9516); -#9519=DIRECTION('',(1.E0,0.E0,0.E0)); -#9520=VECTOR('',#9519,2.978723347187E-1); -#9521=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.450000071526E0)); -#9522=LINE('',#9521,#9520); -#9523=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9524=VECTOR('',#9523,4.5E-1); -#9525=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.900000071526E0)); -#9526=LINE('',#9525,#9524); -#9527=DIRECTION('',(1.E0,0.E0,0.E0)); -#9528=VECTOR('',#9527,1.276595890522E-1); -#9529=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.900000071526E0)); -#9530=LINE('',#9529,#9528); -#9531=DIRECTION('',(-7.852596483189E-1,0.E0,-6.191666049797E-1)); -#9532=VECTOR('',#9531,5.148046654734E-1); -#9533=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.768749928474E0)); -#9534=LINE('',#9533,#9532); -#9535=DIRECTION('',(0.E0,0.E0,1.E0)); -#9536=VECTOR('',#9535,3.187498569489E-1); -#9537=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.450000071526E0)); -#9538=LINE('',#9537,#9536); -#9539=DIRECTION('',(1.E0,0.E0,0.E0)); -#9540=VECTOR('',#9539,4.042553305626E-1); -#9541=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,7.450000071526E0)); -#9542=LINE('',#9541,#9540); -#9543=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9544=VECTOR('',#9543,1.E0); -#9545=CARTESIAN_POINT('',(5.75E0,1.5E0,6.774999856949E0)); -#9546=LINE('',#9545,#9544); -#9547=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9548=VECTOR('',#9547,1.125002145767E-1); -#9549=CARTESIAN_POINT('',(5.75E0,1.5E0,6.887500071526E0)); -#9550=LINE('',#9549,#9548); -#9551=DIRECTION('',(1.E0,0.E0,0.E0)); -#9552=VECTOR('',#9551,8.297872543335E-1); -#9553=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.887500071526E0)); -#9554=LINE('',#9553,#9552); -#9555=DIRECTION('',(-7.979435489134E-1,0.E0,-6.027321899048E-1)); -#9556=VECTOR('',#9555,1.866500609794E-1); -#9557=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,7.000000071526E0)); -#9558=LINE('',#9557,#9556); -#9559=DIRECTION('',(1.E0,0.E0,0.E0)); -#9560=VECTOR('',#9559,1.702128052711E-1); -#9561=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,7.000000071526E0)); -#9562=LINE('',#9561,#9560); -#9563=DIRECTION('',(7.979434329020E-1,0.E0,6.027323434897E-1)); -#9564=VECTOR('',#9563,1.866500134183E-1); -#9565=CARTESIAN_POINT('',(4.75E0,1.5E0,6.887500071526E0)); -#9566=LINE('',#9565,#9564); -#9567=DIRECTION('',(0.E0,0.E0,1.E0)); -#9568=VECTOR('',#9567,1.125002145767E-1); -#9569=CARTESIAN_POINT('',(4.75E0,1.5E0,6.774999856949E0)); -#9570=LINE('',#9569,#9568); -#9571=DIRECTION('',(1.E0,0.E0,0.E0)); -#9572=VECTOR('',#9571,1.914893388748E-1); -#9573=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,6.625E0)); -#9574=LINE('',#9573,#9572); -#9575=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554437E-1)); -#9576=VECTOR('',#9575,1.080226982085E-1); -#9577=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.606249856949E0)); -#9578=LINE('',#9577,#9576); -#9579=DIRECTION('',(9.594621594064E-1,0.E0,2.818374791740E-1)); -#9580=VECTOR('',#9579,6.652668748194E-2); -#9581=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,6.587500143051E0)); -#9582=LINE('',#9581,#9580); -#9583=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#9584=VECTOR('',#9583,9.300196855221E-2); -#9585=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,6.549999856949E0)); -#9586=LINE('',#9585,#9584); -#9587=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#9588=VECTOR('',#9587,8.507821852254E-2); -#9589=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,6.493749856949E0)); -#9590=LINE('',#9589,#9588); -#9591=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#9592=VECTOR('',#9591,1.134163852576E-1); -#9593=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.4E0)); -#9594=LINE('',#9593,#9592); -#9595=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#9596=VECTOR('',#9595,1.144942942620E-1); -#9597=CARTESIAN_POINT('',(4.75E0,1.5E0,6.2875E0)); -#9598=LINE('',#9597,#9596); -#9599=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#9600=VECTOR('',#9599,1.144942942620E-1); -#9601=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.175E0)); -#9602=LINE('',#9601,#9600); -#9603=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#9604=VECTOR('',#9603,1.134163852576E-1); -#9605=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,6.081250143051E0)); -#9606=LINE('',#9605,#9604); -#9607=DIRECTION('',(-7.502481919979E-1,0.E0,6.611562980142E-1)); -#9608=VECTOR('',#9607,8.507821852254E-2); -#9609=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,6.025000143051E0)); -#9610=LINE('',#9609,#9608); -#9611=DIRECTION('',(-9.151029183374E-1,0.E0,4.032203477633E-1)); -#9612=VECTOR('',#9611,9.300196855221E-2); -#9613=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.987499856949E0)); -#9614=LINE('',#9613,#9612); -#9615=DIRECTION('',(-9.594621594064E-1,0.E0,2.818374791740E-1)); -#9616=VECTOR('',#9615,6.652668748194E-2); -#9617=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.968750143051E0)); -#9618=LINE('',#9617,#9616); -#9619=DIRECTION('',(-9.848204850082E-1,0.E0,1.735759554437E-1)); -#9620=VECTOR('',#9619,1.080226982085E-1); -#9621=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.95E0)); -#9622=LINE('',#9621,#9620); -#9623=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9624=VECTOR('',#9623,1.914893388748E-1); -#9625=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.95E0)); -#9626=LINE('',#9625,#9624); -#9627=DIRECTION('',(-9.848204933204E-1,0.E0,-1.735759082829E-1)); -#9628=VECTOR('',#9627,1.080227275584E-1); -#9629=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.968750143051E0)); -#9630=LINE('',#9629,#9628); -#9631=DIRECTION('',(-9.594620882388E-1,0.E0,-2.818377214504E-1)); -#9632=VECTOR('',#9631,6.652663029355E-2); -#9633=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.987499856949E0)); -#9634=LINE('',#9633,#9632); -#9635=DIRECTION('',(-9.151029443877E-1,0.E0,-4.032202886425E-1)); -#9636=VECTOR('',#9635,9.300198218831E-2); -#9637=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.025000143051E0)); -#9638=LINE('',#9637,#9636); -#9639=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#9640=VECTOR('',#9639,8.507822411232E-2); -#9641=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,6.081250143051E0)); -#9642=LINE('',#9641,#9640); -#9643=DIRECTION('',(-5.627915516617E-1,0.E0,-8.265988563857E-1)); -#9644=VECTOR('',#9643,1.134163884024E-1); -#9645=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.175E0)); -#9646=LINE('',#9645,#9644); -#9647=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#9648=VECTOR('',#9647,1.144942946081E-1); -#9649=CARTESIAN_POINT('',(5.75E0,1.5E0,6.2875E0)); -#9650=LINE('',#9649,#9648); -#9651=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#9652=VECTOR('',#9651,1.144942946081E-1); -#9653=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.4E0)); -#9654=LINE('',#9653,#9652); -#9655=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#9656=VECTOR('',#9655,1.134163884024E-1); -#9657=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,6.493749856949E0)); -#9658=LINE('',#9657,#9656); -#9659=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#9660=VECTOR('',#9659,8.507822411232E-2); -#9661=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.549999856949E0)); -#9662=LINE('',#9661,#9660); -#9663=DIRECTION('',(9.151029443877E-1,0.E0,-4.032202886425E-1)); -#9664=VECTOR('',#9663,9.300198218831E-2); -#9665=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,6.587500143051E0)); -#9666=LINE('',#9665,#9664); -#9667=DIRECTION('',(9.594620882388E-1,0.E0,-2.818377214504E-1)); -#9668=VECTOR('',#9667,6.652663029355E-2); -#9669=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.606249856949E0)); -#9670=LINE('',#9669,#9668); -#9671=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#9672=VECTOR('',#9671,1.080227275584E-1); -#9673=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,6.625E0)); -#9674=LINE('',#9673,#9672); -#9675=DIRECTION('',(-9.893851372145E-1,0.E0,-1.453170680242E-1)); -#9676=VECTOR('',#9675,1.290291863584E-1); -#9677=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,6.531250143051E0)); -#9678=LINE('',#9677,#9676); -#9679=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9680=VECTOR('',#9679,1.489361524582E-1); -#9681=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,6.531250143051E0)); -#9682=LINE('',#9681,#9680); -#9683=DIRECTION('',(-9.893851420919E-1,0.E0,1.453170348161E-1)); -#9684=VECTOR('',#9683,1.290292158444E-1); -#9685=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.5125E0)); -#9686=LINE('',#9685,#9684); -#9687=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#9688=VECTOR('',#9687,1.480607589138E-1); -#9689=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,6.437499856949E0)); -#9690=LINE('',#9689,#9688); -#9691=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865771E-1)); -#9692=VECTOR('',#9691,7.053251855852E-2); -#9693=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.381249856949E0)); -#9694=LINE('',#9693,#9692); -#9695=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#9696=VECTOR('',#9695,9.613391231237E-2); -#9697=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,6.2875E0)); -#9698=LINE('',#9697,#9696); -#9699=DIRECTION('',(2.213224521559E-1,0.E0,9.752006830246E-1)); -#9700=VECTOR('',#9699,9.613391231237E-2); -#9701=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.193750143051E0)); -#9702=LINE('',#9701,#9700); -#9703=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#9704=VECTOR('',#9703,7.053251855852E-2); -#9705=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,6.137500143051E0)); -#9706=LINE('',#9705,#9704); -#9707=DIRECTION('',(8.622107240812E-1,0.E0,5.065497678209E-1)); -#9708=VECTOR('',#9707,1.480607589138E-1); -#9709=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.0625E0)); -#9710=LINE('',#9709,#9708); -#9711=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#9712=VECTOR('',#9711,1.290292158444E-1); -#9713=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,6.043749856949E0)); -#9714=LINE('',#9713,#9712); -#9715=DIRECTION('',(1.E0,0.E0,0.E0)); -#9716=VECTOR('',#9715,1.489361524582E-1); -#9717=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,6.043749856949E0)); -#9718=LINE('',#9717,#9716); -#9719=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#9720=VECTOR('',#9719,1.290291863584E-1); -#9721=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.0625E0)); -#9722=LINE('',#9721,#9720); -#9723=DIRECTION('',(8.622108015533E-1,0.E0,-5.065496359537E-1)); -#9724=VECTOR('',#9723,1.480607974576E-1); -#9725=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.137500143051E0)); -#9726=LINE('',#9725,#9724); -#9727=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#9728=VECTOR('',#9727,7.053251855852E-2); -#9729=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.193750143051E0)); -#9730=LINE('',#9729,#9728); -#9731=DIRECTION('',(2.213224521559E-1,0.E0,-9.752006830246E-1)); -#9732=VECTOR('',#9731,9.613391231237E-2); -#9733=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,6.2875E0)); -#9734=LINE('',#9733,#9732); -#9735=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#9736=VECTOR('',#9735,9.613391231237E-2); -#9737=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.381249856949E0)); -#9738=LINE('',#9737,#9736); -#9739=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865771E-1)); -#9740=VECTOR('',#9739,7.053251855852E-2); -#9741=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.437499856949E0)); -#9742=LINE('',#9741,#9740); -#9743=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#9744=VECTOR('',#9743,1.480607974576E-1); -#9745=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.5125E0)); -#9746=LINE('',#9745,#9744); -#9747=DIRECTION('',(1.E0,0.E0,0.E0)); -#9748=VECTOR('',#9747,1.914893388748E-1); -#9749=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.800000143051E0)); -#9750=LINE('',#9749,#9748); -#9751=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554438E-1)); -#9752=VECTOR('',#9751,1.080226982085E-1); -#9753=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.78125E0)); -#9754=LINE('',#9753,#9752); -#9755=DIRECTION('',(9.594604150024E-1,0.E0,2.818434175982E-1)); -#9756=VECTOR('',#9755,6.652680843474E-2); -#9757=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.762499856949E0)); -#9758=LINE('',#9757,#9756); -#9759=DIRECTION('',(9.151046210117E-1,0.E0,4.032164835459E-1)); -#9760=VECTOR('',#9759,9.300179550964E-2); -#9761=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,5.725E0)); -#9762=LINE('',#9761,#9760); -#9763=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#9764=VECTOR('',#9763,8.507821852253E-2); -#9765=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,5.66875E0)); -#9766=LINE('',#9765,#9764); -#9767=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#9768=VECTOR('',#9767,1.134163852576E-1); -#9769=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,5.575000143051E0)); -#9770=LINE('',#9769,#9768); -#9771=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#9772=VECTOR('',#9771,1.144942942620E-1); -#9773=CARTESIAN_POINT('',(4.75E0,1.5E0,5.462500143051E0)); -#9774=LINE('',#9773,#9772); -#9775=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#9776=VECTOR('',#9775,1.144942942620E-1); -#9777=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,5.350000143051E0)); -#9778=LINE('',#9777,#9776); -#9779=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#9780=VECTOR('',#9779,1.134167399956E-1); -#9781=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,5.256249856949E0)); -#9782=LINE('',#9781,#9780); -#9783=DIRECTION('',(-7.502481919979E-1,0.E0,6.611562980142E-1)); -#9784=VECTOR('',#9783,8.507821852254E-2); -#9785=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,5.199999856949E0)); -#9786=LINE('',#9785,#9784); -#9787=DIRECTION('',(-9.151046210116E-1,0.E0,4.032164835459E-1)); -#9788=VECTOR('',#9787,9.300179550964E-2); -#9789=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.1625E0)); -#9790=LINE('',#9789,#9788); -#9791=DIRECTION('',(-9.594604150024E-1,0.E0,2.818434175982E-1)); -#9792=VECTOR('',#9791,6.652680843474E-2); -#9793=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.143749856949E0)); -#9794=LINE('',#9793,#9792); -#9795=DIRECTION('',(-9.848211641175E-1,0.E0,1.735721023269E-1)); -#9796=VECTOR('',#9795,1.080226237186E-1); -#9797=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.125000143051E0)); -#9798=LINE('',#9797,#9796); -#9799=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9800=VECTOR('',#9799,1.914893388748E-1); -#9801=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.125000143051E0)); -#9802=LINE('',#9801,#9800); -#9803=DIRECTION('',(-9.848211724293E-1,0.E0,-1.735720551671E-1)); -#9804=VECTOR('',#9803,1.080226530685E-1); -#9805=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.143749856949E0)); -#9806=LINE('',#9805,#9804); -#9807=DIRECTION('',(-9.594603438319E-1,0.E0,-2.818436598788E-1)); -#9808=VECTOR('',#9807,6.652675124645E-2); -#9809=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.1625E0)); -#9810=LINE('',#9809,#9808); -#9811=DIRECTION('',(-9.151046470615E-1,0.E0,-4.032164244255E-1)); -#9812=VECTOR('',#9811,9.300180914576E-2); -#9813=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,5.199999856949E0)); -#9814=LINE('',#9813,#9812); -#9815=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#9816=VECTOR('',#9815,8.507822411232E-2); -#9817=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,5.256249856949E0)); -#9818=LINE('',#9817,#9816); -#9819=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#9820=VECTOR('',#9819,1.134167431404E-1); -#9821=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,5.350000143051E0)); -#9822=LINE('',#9821,#9820); -#9823=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#9824=VECTOR('',#9823,1.144942946081E-1); -#9825=CARTESIAN_POINT('',(5.75E0,1.5E0,5.462500143051E0)); -#9826=LINE('',#9825,#9824); -#9827=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#9828=VECTOR('',#9827,1.144942946081E-1); -#9829=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,5.575000143051E0)); -#9830=LINE('',#9829,#9828); -#9831=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#9832=VECTOR('',#9831,1.134163884024E-1); -#9833=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,5.66875E0)); -#9834=LINE('',#9833,#9832); -#9835=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#9836=VECTOR('',#9835,8.507822411232E-2); -#9837=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,5.725E0)); -#9838=LINE('',#9837,#9836); -#9839=DIRECTION('',(9.151046470615E-1,0.E0,-4.032164244254E-1)); -#9840=VECTOR('',#9839,9.300180914576E-2); -#9841=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.762499856949E0)); -#9842=LINE('',#9841,#9840); -#9843=DIRECTION('',(9.594603438319E-1,0.E0,-2.818436598788E-1)); -#9844=VECTOR('',#9843,6.652675124645E-2); -#9845=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.78125E0)); -#9846=LINE('',#9845,#9844); -#9847=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#9848=VECTOR('',#9847,1.080227275584E-1); -#9849=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.800000143051E0)); -#9850=LINE('',#9849,#9848); -#9851=DIRECTION('',(-9.893856154061E-1,0.E0,-1.453138122392E-1)); -#9852=VECTOR('',#9851,1.290291239958E-1); -#9853=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.706249856949E0)); -#9854=LINE('',#9853,#9852); -#9855=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9856=VECTOR('',#9855,1.489361524582E-1); -#9857=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,5.706249856949E0)); -#9858=LINE('',#9857,#9856); -#9859=DIRECTION('',(-9.893856202834E-1,0.E0,1.453137790318E-1)); -#9860=VECTOR('',#9859,1.290291534818E-1); -#9861=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.687500143051E0)); -#9862=LINE('',#9861,#9860); -#9863=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#9864=VECTOR('',#9863,1.480607589138E-1); -#9865=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,5.6125E0)); -#9866=LINE('',#9865,#9864); -#9867=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865770E-1)); -#9868=VECTOR('',#9867,7.053251855852E-2); -#9869=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,5.55625E0)); -#9870=LINE('',#9869,#9868); -#9871=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#9872=VECTOR('',#9871,9.613391231237E-2); -#9873=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,5.462500143051E0)); -#9874=LINE('',#9873,#9872); -#9875=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#9876=VECTOR('',#9875,9.613433082315E-2); -#9877=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,5.368749856949E0)); -#9878=LINE('',#9877,#9876); -#9879=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#9880=VECTOR('',#9879,7.053251855852E-2); -#9881=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,5.312499856949E0)); -#9882=LINE('',#9881,#9880); -#9883=DIRECTION('',(8.622119900059E-1,0.E0,5.065476130533E-1)); -#9884=VECTOR('',#9883,1.480605415266E-1); -#9885=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.237500143051E0)); -#9886=LINE('',#9885,#9884); -#9887=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#9888=VECTOR('',#9887,1.290292158444E-1); -#9889=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,5.21875E0)); -#9890=LINE('',#9889,#9888); -#9891=DIRECTION('',(1.E0,0.E0,0.E0)); -#9892=VECTOR('',#9891,1.489361524582E-1); -#9893=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.21875E0)); -#9894=LINE('',#9893,#9892); -#9895=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#9896=VECTOR('',#9895,1.290291863584E-1); -#9897=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.237500143051E0)); -#9898=LINE('',#9897,#9896); -#9899=DIRECTION('',(8.622120674775E-1,0.E0,-5.065474811863E-1)); -#9900=VECTOR('',#9899,1.480605800705E-1); -#9901=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,5.312499856949E0)); -#9902=LINE('',#9901,#9900); -#9903=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#9904=VECTOR('',#9903,7.053251855852E-2); -#9905=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,5.368749856949E0)); -#9906=LINE('',#9905,#9904); -#9907=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#9908=VECTOR('',#9907,9.613433082315E-2); -#9909=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,5.462500143051E0)); -#9910=LINE('',#9909,#9908); -#9911=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#9912=VECTOR('',#9911,9.613391231237E-2); -#9913=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,5.55625E0)); -#9914=LINE('',#9913,#9912); -#9915=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#9916=VECTOR('',#9915,7.053251855852E-2); -#9917=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,5.6125E0)); -#9918=LINE('',#9917,#9916); -#9919=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#9920=VECTOR('',#9919,1.480607974576E-1); -#9921=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.687500143051E0)); -#9922=LINE('',#9921,#9920); -#9923=DIRECTION('',(0.E0,0.E0,1.E0)); -#9924=VECTOR('',#9923,1.500002861023E-1); -#9925=CARTESIAN_POINT('',(4.75E0,1.5E0,4.524999856949E0)); -#9926=LINE('',#9925,#9924); -#9927=DIRECTION('',(-9.578263606440E-1,0.E0,2.873476341569E-1)); -#9928=VECTOR('',#9927,1.044030568680E0); -#9929=CARTESIAN_POINT('',(5.75E0,1.5E0,4.225000143051E0)); -#9930=LINE('',#9929,#9928); -#9931=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9932=VECTOR('',#9931,1.125E-1); -#9933=CARTESIAN_POINT('',(5.75E0,1.5E0,4.337500143051E0)); -#9934=LINE('',#9933,#9932); -#9935=DIRECTION('',(9.594612249353E-1,0.E0,-2.818406603838E-1)); -#9936=VECTOR('',#9935,2.661067916729E-1); -#9937=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,4.412499856949E0)); -#9938=LINE('',#9937,#9936); -#9939=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9940=VECTOR('',#9939,3.750002861023E-1); -#9941=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,4.787500143051E0)); -#9942=LINE('',#9941,#9940); -#9943=DIRECTION('',(-9.594612249353E-1,0.E0,-2.818406603838E-1)); -#9944=VECTOR('',#9943,2.661067916729E-1); -#9945=CARTESIAN_POINT('',(5.75E0,1.5E0,4.862499856949E0)); -#9946=LINE('',#9945,#9944); -#9947=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9948=VECTOR('',#9947,1.125E-1); -#9949=CARTESIAN_POINT('',(5.75E0,1.5E0,4.974999856949E0)); -#9950=LINE('',#9949,#9948); -#9951=DIRECTION('',(9.578263606440E-1,0.E0,2.873476341569E-1)); -#9952=VECTOR('',#9951,1.044030568680E0); -#9953=CARTESIAN_POINT('',(4.75E0,1.5E0,4.675000143051E0)); -#9954=LINE('',#9953,#9952); -#9955=DIRECTION('',(9.594609371659E-1,0.E0,-2.818416400264E-1)); -#9956=VECTOR('',#9955,5.987404841393E-1); -#9957=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,4.6E0)); -#9958=LINE('',#9957,#9956); -#9959=DIRECTION('',(-9.594609371659E-1,0.E0,-2.818416400264E-1)); -#9960=VECTOR('',#9959,5.987404841393E-1); -#9961=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,4.76875E0)); -#9962=LINE('',#9961,#9960); -#9963=DIRECTION('',(0.E0,0.E0,1.E0)); -#9964=VECTOR('',#9963,3.375E-1); -#9965=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,4.43125E0)); -#9966=LINE('',#9965,#9964); -#9967=DIRECTION('',(-1.E0,0.E0,0.E0)); -#9968=VECTOR('',#9967,1.063829958439E-1); -#9969=CARTESIAN_POINT('',(5.388297885656E0,1.5E0,3.8125E0)); -#9970=LINE('',#9969,#9968); -#9971=DIRECTION('',(0.E0,0.E0,-1.E0)); -#9972=VECTOR('',#9971,2.624998569489E-1); -#9973=CARTESIAN_POINT('',(5.388297885656E0,1.5E0,4.074999856949E0)); -#9974=LINE('',#9973,#9972); -#9975=DIRECTION('',(1.E0,0.E0,0.E0)); -#9976=VECTOR('',#9975,1.063829958439E-1); -#9977=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,4.074999856949E0)); -#9978=LINE('',#9977,#9976); -#9979=DIRECTION('',(0.E0,0.E0,1.E0)); -#9980=VECTOR('',#9979,2.624998569489E-1); -#9981=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,3.8125E0)); -#9982=LINE('',#9981,#9980); -#9983=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#9984=VECTOR('',#9983,4.311571495761E-2); -#9985=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,3.08125E0)); -#9986=LINE('',#9985,#9984); -#9987=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#9988=VECTOR('',#9987,4.311571495761E-2); -#9989=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,3.043749713898E0)); -#9990=LINE('',#9989,#9988); -#9991=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#9992=VECTOR('',#9991,1.020154752811E-1); -#9993=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,2.987499713898E0)); -#9994=LINE('',#9993,#9992); -#9995=DIRECTION('',(-9.594621238227E-1,0.E0,2.818376003121E-1)); -#9996=VECTOR('',#9995,6.652665888774E-2); -#9997=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,2.96875E0)); -#9998=LINE('',#9997,#9996); -#9999=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10000=VECTOR('',#9999,1.063829660416E-1); -#10001=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,2.96875E0)); -#10002=LINE('',#10001,#10000); -#10003=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#10004=VECTOR('',#10003,6.652664459064E-2); -#10005=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,2.987499713898E0)); -#10006=LINE('',#10005,#10004); -#10007=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#10008=VECTOR('',#10007,1.020154814968E-1); -#10009=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,3.043749713898E0)); -#10010=LINE('',#10009,#10008); -#10011=DIRECTION('',(-6.481157499635E-1,0.E0,-7.615418403799E-1)); -#10012=VECTOR('',#10011,9.848516289948E-2); -#10013=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,3.118750286102E0)); -#10014=LINE('',#10013,#10012); -#10015=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#10016=VECTOR('',#10015,9.613349421393E-2); -#10017=CARTESIAN_POINT('',(5.75E0,1.5E0,3.212499713898E0)); -#10018=LINE('',#10017,#10016); -#10019=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10020=VECTOR('',#10019,4.500004291534E-1); -#10021=CARTESIAN_POINT('',(5.75E0,1.5E0,3.662500143051E0)); -#10022=LINE('',#10021,#10020); -#10023=DIRECTION('',(1.E0,0.E0,0.E0)); -#10024=VECTOR('',#10023,1.E0); -#10025=CARTESIAN_POINT('',(4.75E0,1.5E0,3.662500143051E0)); -#10026=LINE('',#10025,#10024); -#10027=DIRECTION('',(0.E0,0.E0,1.E0)); -#10028=VECTOR('',#10027,4.500004291534E-1); -#10029=CARTESIAN_POINT('',(4.75E0,1.5E0,3.212499713898E0)); -#10030=LINE('',#10029,#10028); -#10031=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#10032=VECTOR('',#10031,9.613349380169E-2); -#10033=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,3.118750286102E0)); -#10034=LINE('',#10033,#10032); -#10035=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#10036=VECTOR('',#10035,9.848515927785E-2); -#10037=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,3.043749713898E0)); -#10038=LINE('',#10037,#10036); -#10039=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#10040=VECTOR('',#10039,1.020154752811E-1); -#10041=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,2.987499713898E0)); -#10042=LINE('',#10041,#10040); -#10043=DIRECTION('',(-9.594620882388E-1,0.E0,2.818377214504E-1)); -#10044=VECTOR('',#10043,6.652663029355E-2); -#10045=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,2.96875E0)); -#10046=LINE('',#10045,#10044); -#10047=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10048=VECTOR('',#10047,8.510643243790E-2); -#10049=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,2.96875E0)); -#10050=LINE('',#10049,#10048); -#10051=DIRECTION('',(-9.594620882388E-1,0.E0,-2.818377214504E-1)); -#10052=VECTOR('',#10051,6.652663029355E-2); -#10053=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,2.987499713898E0)); -#10054=LINE('',#10053,#10052); -#10055=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#10056=VECTOR('',#10055,1.020154752811E-1); -#10057=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,3.043749713898E0)); -#10058=LINE('',#10057,#10056); -#10059=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10060=VECTOR('',#10059,3.562501430511E-1); -#10061=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,3.550000143051E0)); -#10062=LINE('',#10061,#10060); -#10063=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10064=VECTOR('',#10063,2.978723645210E-1); -#10065=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,3.550000143051E0)); -#10066=LINE('',#10065,#10064); -#10067=DIRECTION('',(0.E0,0.E0,1.E0)); -#10068=VECTOR('',#10067,3.562501430511E-1); -#10069=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,3.19375E0)); -#10070=LINE('',#10069,#10068); -#10071=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#10072=VECTOR('',#10071,6.013947055430E-2); -#10073=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,3.1375E0)); -#10074=LINE('',#10073,#10072); -#10075=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#10076=VECTOR('',#10075,5.671900150710E-2); -#10077=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,3.099999713898E0)); -#10078=LINE('',#10077,#10076); -#10079=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#10080=VECTOR('',#10079,6.652663029355E-2); -#10081=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,3.08125E0)); -#10082=LINE('',#10081,#10080); -#10083=DIRECTION('',(1.E0,0.E0,0.E0)); -#10084=VECTOR('',#10083,4.255318641663E-2); -#10085=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,3.08125E0)); -#10086=LINE('',#10085,#10084); -#10087=DIRECTION('',(9.594621594064E-1,0.E0,-2.818374791740E-1)); -#10088=VECTOR('',#10087,6.652668748194E-2); -#10089=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,3.099999713898E0)); -#10090=LINE('',#10089,#10088); -#10091=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#10092=VECTOR('',#10091,5.671900150710E-2); -#10093=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,3.1375E0)); -#10094=LINE('',#10093,#10092); -#10095=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#10096=VECTOR('',#10095,6.013947055430E-2); -#10097=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,3.19375E0)); -#10098=LINE('',#10097,#10096); -#10099=DIRECTION('',(1.E0,0.E0,0.E0)); -#10100=VECTOR('',#10099,6.382977962494E-2); -#10101=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,3.08125E0)); -#10102=LINE('',#10101,#10100); -#10103=DIRECTION('',(9.594621238227E-1,0.E0,-2.818376003121E-1)); -#10104=VECTOR('',#10103,6.652665888774E-2); -#10105=CARTESIAN_POINT('',(5.367021262646E0,1.5E0,3.099999713898E0)); -#10106=LINE('',#10105,#10104); -#10107=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#10108=VECTOR('',#10107,5.671900150710E-2); -#10109=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,3.1375E0)); -#10110=LINE('',#10109,#10108); -#10111=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#10112=VECTOR('',#10111,6.013947055430E-2); -#10113=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,3.19375E0)); -#10114=LINE('',#10113,#10112); -#10115=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10116=VECTOR('',#10115,3.562501430511E-1); -#10117=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,3.550000143051E0)); -#10118=LINE('',#10117,#10116); -#10119=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10120=VECTOR('',#10119,3.191489428282E-1); -#10121=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,3.550000143051E0)); -#10122=LINE('',#10121,#10120); -#10123=DIRECTION('',(0.E0,0.E0,1.E0)); -#10124=VECTOR('',#10123,3.562501430511E-1); -#10125=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,3.19375E0)); -#10126=LINE('',#10125,#10124); -#10127=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#10128=VECTOR('',#10127,6.013947055430E-2); -#10129=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,3.1375E0)); -#10130=LINE('',#10129,#10128); -#10131=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#10132=VECTOR('',#10131,5.671901268663E-2); -#10133=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,3.099999713898E0)); -#10134=LINE('',#10133,#10132); -#10135=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#10136=VECTOR('',#10135,6.652663029355E-2); -#10137=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,3.08125E0)); -#10138=LINE('',#10137,#10136); -#10139=DIRECTION('',(0.E0,0.E0,1.E0)); -#10140=VECTOR('',#10139,7.124994277954E-1); -#10141=CARTESIAN_POINT('',(4.75E0,1.5E0,2.106250286102E0)); -#10142=LINE('',#10141,#10140); -#10143=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10144=VECTOR('',#10143,1.063829660416E-1); -#10145=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.106250286102E0)); -#10146=LINE('',#10145,#10144); -#10147=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10148=VECTOR('',#10147,2.999997138977E-1); -#10149=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.40625E0)); -#10150=LINE('',#10149,#10148); -#10151=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10152=VECTOR('',#10151,8.936170339584E-1); -#10153=CARTESIAN_POINT('',(5.75E0,1.5E0,2.40625E0)); -#10154=LINE('',#10153,#10152); -#10155=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10156=VECTOR('',#10155,1.125E-1); -#10157=CARTESIAN_POINT('',(5.75E0,1.5E0,2.51875E0)); -#10158=LINE('',#10157,#10156); -#10159=DIRECTION('',(1.E0,0.E0,0.E0)); -#10160=VECTOR('',#10159,8.936170339584E-1); -#10161=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.51875E0)); -#10162=LINE('',#10161,#10160); -#10163=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10164=VECTOR('',#10163,2.999997138977E-1); -#10165=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.818749713898E0)); -#10166=LINE('',#10165,#10164); -#10167=DIRECTION('',(1.E0,0.E0,0.E0)); -#10168=VECTOR('',#10167,1.063829660416E-1); -#10169=CARTESIAN_POINT('',(4.75E0,1.5E0,2.818749713898E0)); -#10170=LINE('',#10169,#10168); -#10171=DIRECTION('',(4.934765254208E-1,0.E0,8.697591154214E-1)); -#10172=VECTOR('',#10171,4.311571495761E-2); -#10173=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,1.806249713898E0)); -#10174=LINE('',#10173,#10172); -#10175=DIRECTION('',(4.934765254207E-1,0.E0,-8.697591154214E-1)); -#10176=VECTOR('',#10175,4.311571495761E-2); -#10177=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,1.84375E0)); -#10178=LINE('',#10177,#10176); -#10179=DIRECTION('',(7.502481919979E-1,0.E0,-6.611562980142E-1)); -#10180=VECTOR('',#10179,8.507821852254E-2); -#10181=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,1.9E0)); -#10182=LINE('',#10181,#10180); -#10183=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#10184=VECTOR('',#10183,9.300196855221E-2); -#10185=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,1.937500286102E0)); -#10186=LINE('',#10185,#10184); -#10187=DIRECTION('',(1.E0,0.E0,0.E0)); -#10188=VECTOR('',#10187,6.382977962494E-2); -#10189=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.937500286102E0)); -#10190=LINE('',#10189,#10188); -#10191=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#10192=VECTOR('',#10191,1.127990230605E-1); -#10193=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.9E0)); -#10194=LINE('',#10193,#10192); -#10195=DIRECTION('',(7.502481919979E-1,0.E0,6.611562980142E-1)); -#10196=VECTOR('',#10195,8.507821852254E-2); -#10197=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,1.84375E0)); -#10198=LINE('',#10197,#10196); -#10199=DIRECTION('',(5.627897577325E-1,0.E0,8.266000777833E-1)); -#10200=VECTOR('',#10199,1.134167399956E-1); -#10201=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.749999713898E0)); -#10202=LINE('',#10201,#10200); -#10203=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#10204=VECTOR('',#10203,9.613349380169E-2); -#10205=CARTESIAN_POINT('',(4.75E0,1.5E0,1.656250286102E0)); -#10206=LINE('',#10205,#10204); -#10207=DIRECTION('',(0.E0,0.E0,1.E0)); -#10208=VECTOR('',#10207,7.500057220459E-2); -#10209=CARTESIAN_POINT('',(4.75E0,1.5E0,1.581249713898E0)); -#10210=LINE('',#10209,#10208); -#10211=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#10212=VECTOR('',#10211,9.613349380168E-2); -#10213=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.487500286102E0)); -#10214=LINE('',#10213,#10212); -#10215=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#10216=VECTOR('',#10215,1.134167399956E-1); -#10217=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,1.39375E0)); -#10218=LINE('',#10217,#10216); -#10219=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#10220=VECTOR('',#10219,8.507821852254E-2); -#10221=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.3375E0)); -#10222=LINE('',#10221,#10220); -#10223=DIRECTION('',(-9.431200976730E-1,0.E0,3.324522241845E-1)); -#10224=VECTOR('',#10223,1.127990230605E-1); -#10225=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.299999713898E0)); -#10226=LINE('',#10225,#10224); -#10227=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10228=VECTOR('',#10227,6.382977962494E-2); -#10229=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,1.299999713898E0)); -#10230=LINE('',#10229,#10228); -#10231=DIRECTION('',(-9.151029183374E-1,0.E0,-4.032203477633E-1)); -#10232=VECTOR('',#10231,9.300196855221E-2); -#10233=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,1.3375E0)); -#10234=LINE('',#10233,#10232); -#10235=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#10236=VECTOR('',#10235,8.507821852253E-2); -#10237=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,1.39375E0)); -#10238=LINE('',#10237,#10236); -#10239=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#10240=VECTOR('',#10239,4.311571495761E-2); -#10241=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,1.431250286102E0)); -#10242=LINE('',#10241,#10240); -#10243=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#10244=VECTOR('',#10243,4.311571495761E-2); -#10245=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,1.39375E0)); -#10246=LINE('',#10245,#10244); -#10247=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#10248=VECTOR('',#10247,9.848450564280E-2); -#10249=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,1.318750286102E0)); -#10250=LINE('',#10249,#10248); -#10251=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#10252=VECTOR('',#10251,1.127989949533E-1); -#10253=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.28125E0)); -#10254=LINE('',#10253,#10252); -#10255=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10256=VECTOR('',#10255,6.382977962494E-2); -#10257=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.28125E0)); -#10258=LINE('',#10257,#10256); -#10259=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#10260=VECTOR('',#10259,1.127989808997E-1); -#10261=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.318750286102E0)); -#10262=LINE('',#10261,#10260); -#10263=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#10264=VECTOR('',#10263,8.507822411232E-2); -#10265=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,1.375000286102E0)); -#10266=LINE('',#10265,#10264); -#10267=DIRECTION('',(-5.627933119354E-1,0.E0,-8.265976578970E-1)); -#10268=VECTOR('',#10267,1.134160336649E-1); -#10269=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,1.468749713898E0)); -#10270=LINE('',#10269,#10268); -#10271=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#10272=VECTOR('',#10271,9.613433123539E-2); -#10273=CARTESIAN_POINT('',(5.75E0,1.5E0,1.5625E0)); -#10274=LINE('',#10273,#10272); -#10275=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10276=VECTOR('',#10275,1.125E-1); -#10277=CARTESIAN_POINT('',(5.75E0,1.5E0,1.675E0)); -#10278=LINE('',#10277,#10276); -#10279=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#10280=VECTOR('',#10279,9.613433123539E-2); -#10281=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,1.768750286102E0)); -#10282=LINE('',#10281,#10280); -#10283=DIRECTION('',(5.627933119354E-1,0.E0,-8.265976578970E-1)); -#10284=VECTOR('',#10283,1.134160336649E-1); -#10285=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,1.862499713898E0)); -#10286=LINE('',#10285,#10284); -#10287=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#10288=VECTOR('',#10287,8.507822411232E-2); -#10289=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.918749713898E0)); -#10290=LINE('',#10289,#10288); -#10291=DIRECTION('',(9.431200538709E-1,0.E0,-3.324523484448E-1)); -#10292=VECTOR('',#10291,1.127989808997E-1); -#10293=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.95625E0)); -#10294=LINE('',#10293,#10292); -#10295=DIRECTION('',(1.E0,0.E0,0.E0)); -#10296=VECTOR('',#10295,6.382977962494E-2); -#10297=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.95625E0)); -#10298=LINE('',#10297,#10296); -#10299=DIRECTION('',(9.431200684716E-1,0.E0,3.324523070247E-1)); -#10300=VECTOR('',#10299,1.127989949533E-1); -#10301=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,1.918749713898E0)); -#10302=LINE('',#10301,#10300); -#10303=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#10304=VECTOR('',#10303,9.848450564280E-2); -#10305=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,1.84375E0)); -#10306=LINE('',#10305,#10304); -#10307=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#10308=VECTOR('',#10307,7.795928747295E-2); -#10309=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.656250286102E0)); -#10310=LINE('',#10309,#10308); -#10311=DIRECTION('',(0.E0,0.E0,1.E0)); -#10312=VECTOR('',#10311,7.500057220459E-2); -#10313=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.581249713898E0)); -#10314=LINE('',#10313,#10312); -#10315=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#10316=VECTOR('',#10315,7.795928747295E-2); -#10317=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,1.50625E0)); -#10318=LINE('',#10317,#10316); -#10319=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#10320=VECTOR('',#10319,8.623068339603E-2); -#10321=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.431250286102E0)); -#10322=LINE('',#10321,#10320); -#10323=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#10324=VECTOR('',#10323,1.020154877124E-1); -#10325=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.375000286102E0)); -#10326=LINE('',#10325,#10324); -#10327=DIRECTION('',(1.E0,0.E0,0.E0)); -#10328=VECTOR('',#10327,6.382977962494E-2); -#10329=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.375000286102E0)); -#10330=LINE('',#10329,#10328); -#10331=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#10332=VECTOR('',#10331,1.020155001437E-1); -#10333=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,1.431250286102E0)); -#10334=LINE('',#10333,#10332); -#10335=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#10336=VECTOR('',#10335,8.623068339603E-2); -#10337=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,1.50625E0)); -#10338=LINE('',#10337,#10336); -#10339=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#10340=VECTOR('',#10339,7.795928747295E-2); -#10341=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,1.581249713898E0)); -#10342=LINE('',#10341,#10340); -#10343=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10344=VECTOR('',#10343,7.500057220459E-2); -#10345=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,1.656250286102E0)); -#10346=LINE('',#10345,#10344); -#10347=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#10348=VECTOR('',#10347,7.795928747295E-2); -#10349=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,1.73125E0)); -#10350=LINE('',#10349,#10348); -#10351=DIRECTION('',(-4.934807975624E-1,0.E0,-8.697566915162E-1)); -#10352=VECTOR('',#10351,8.623068339603E-2); -#10353=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,1.806249713898E0)); -#10354=LINE('',#10353,#10352); -#10355=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#10356=VECTOR('',#10355,1.020155001437E-1); -#10357=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.862499713898E0)); -#10358=LINE('',#10357,#10356); -#10359=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10360=VECTOR('',#10359,6.382977962494E-2); -#10361=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.862499713898E0)); -#10362=LINE('',#10361,#10360); -#10363=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654784E-1)); -#10364=VECTOR('',#10363,1.020154877124E-1); -#10365=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.806249713898E0)); -#10366=LINE('',#10365,#10364); -#10367=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#10368=VECTOR('',#10367,8.623068339603E-2); -#10369=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,1.73125E0)); -#10370=LINE('',#10369,#10368); -#10371=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#10372=VECTOR('',#10371,7.795928747295E-2); -#10373=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,1.581249713898E0)); -#10374=LINE('',#10373,#10372); -#10375=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10376=VECTOR('',#10375,7.500057220459E-2); -#10377=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,1.656250286102E0)); -#10378=LINE('',#10377,#10376); -#10379=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#10380=VECTOR('',#10379,7.795928747295E-2); -#10381=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.73125E0)); -#10382=LINE('',#10381,#10380); -#10383=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#10384=VECTOR('',#10383,9.848450564280E-2); -#10385=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.806249713898E0)); -#10386=LINE('',#10385,#10384); -#10387=DIRECTION('',(-8.622096389243E-1,0.E0,-5.065516148884E-1)); -#10388=VECTOR('',#10387,7.403053311863E-2); -#10389=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.84375E0)); -#10390=LINE('',#10389,#10388); -#10391=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10392=VECTOR('',#10391,4.255318641663E-2); -#10393=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,1.84375E0)); -#10394=LINE('',#10393,#10392); -#10395=DIRECTION('',(-8.622094323306E-1,0.E0,5.065519665347E-1)); -#10396=VECTOR('',#10395,7.403048172694E-2); -#10397=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,1.806249713898E0)); -#10398=LINE('',#10397,#10396); -#10399=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#10400=VECTOR('',#10399,9.848450564280E-2); -#10401=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,1.73125E0)); -#10402=LINE('',#10401,#10400); -#10403=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#10404=VECTOR('',#10403,7.795928747295E-2); -#10405=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,1.656250286102E0)); -#10406=LINE('',#10405,#10404); -#10407=DIRECTION('',(0.E0,0.E0,1.E0)); -#10408=VECTOR('',#10407,7.500057220459E-2); -#10409=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,1.581249713898E0)); -#10410=LINE('',#10409,#10408); -#10411=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#10412=VECTOR('',#10411,7.795928747295E-2); -#10413=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,1.50625E0)); -#10414=LINE('',#10413,#10412); -#10415=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#10416=VECTOR('',#10415,9.848450564280E-2); -#10417=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,1.431250286102E0)); -#10418=LINE('',#10417,#10416); -#10419=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#10420=VECTOR('',#10419,7.403048172694E-2); -#10421=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,1.39375E0)); -#10422=LINE('',#10421,#10420); -#10423=DIRECTION('',(1.E0,0.E0,0.E0)); -#10424=VECTOR('',#10423,4.255318641663E-2); -#10425=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.39375E0)); -#10426=LINE('',#10425,#10424); -#10427=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#10428=VECTOR('',#10427,7.403053311863E-2); -#10429=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.431250286102E0)); -#10430=LINE('',#10429,#10428); -#10431=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#10432=VECTOR('',#10431,9.848450564280E-2); -#10433=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.50625E0)); -#10434=LINE('',#10433,#10432); -#10435=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#10436=VECTOR('',#10435,7.403004695359E-2); -#10437=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,5.124997138977E-1)); -#10438=LINE('',#10437,#10436); -#10439=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#10440=VECTOR('',#10439,7.053252305355E-2); -#10441=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,5.687497138977E-1)); -#10442=LINE('',#10441,#10440); -#10443=DIRECTION('',(-4.934765744419E-1,0.E0,-8.697590876082E-1)); -#10444=VECTOR('',#10443,8.623143267274E-2); -#10445=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.437502861023E-1)); -#10446=LINE('',#10445,#10444); -#10447=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#10448=VECTOR('',#10447,7.795928798130E-2); -#10449=CARTESIAN_POINT('',(5.75E0,1.5E0,7.1875E-1)); -#10450=LINE('',#10449,#10448); -#10451=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10452=VECTOR('',#10451,1.500002861023E-1); -#10453=CARTESIAN_POINT('',(5.75E0,1.5E0,8.687502861023E-1)); -#10454=LINE('',#10453,#10452); -#10455=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#10456=VECTOR('',#10455,7.795928798130E-2); -#10457=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.4375E-1)); -#10458=LINE('',#10457,#10456); -#10459=DIRECTION('',(4.934808465838E-1,0.E0,-8.697566637025E-1)); -#10460=VECTOR('',#10459,8.623068615356E-2); -#10461=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,1.018749713898E0)); -#10462=LINE('',#10461,#10460); -#10463=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#10464=VECTOR('',#10463,7.053252305355E-2); -#10465=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.074999713898E0)); -#10466=LINE('',#10465,#10464); -#10467=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#10468=VECTOR('',#10467,7.403048172694E-2); -#10469=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.1125E0)); -#10470=LINE('',#10469,#10468); -#10471=DIRECTION('',(9.594621060308E-1,0.E0,-2.818376608812E-1)); -#10472=VECTOR('',#10471,6.652664459064E-2); -#10473=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.131249713898E0)); -#10474=LINE('',#10473,#10472); -#10475=DIRECTION('',(0.E0,0.E0,1.E0)); -#10476=VECTOR('',#10475,9.374942779541E-2); -#10477=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.037500286102E0)); -#10478=LINE('',#10477,#10476); -#10479=DIRECTION('',(-9.150995129590E-1,0.E0,4.032280761334E-1)); -#10480=VECTOR('',#10479,4.650115732116E-2); -#10481=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,1.018749713898E0)); -#10482=LINE('',#10481,#10480); -#10483=DIRECTION('',(-7.502533110351E-1,0.E0,6.611504891330E-1)); -#10484=VECTOR('',#10483,5.671844521296E-2); -#10485=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.812502861023E-1)); -#10486=LINE('',#10485,#10484); -#10487=DIRECTION('',(-4.934765254208E-1,0.E0,8.697591154214E-1)); -#10488=VECTOR('',#10487,4.311571495761E-2); -#10489=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.4375E-1)); -#10490=LINE('',#10489,#10488); -#10491=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#10492=VECTOR('',#10491,9.613433082315E-2); -#10493=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.499997138977E-1)); -#10494=LINE('',#10493,#10492); -#10495=DIRECTION('',(0.E0,0.E0,1.E0)); -#10496=VECTOR('',#10495,1.125E-1); -#10497=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,7.374997138977E-1)); -#10498=LINE('',#10497,#10496); -#10499=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#10500=VECTOR('',#10499,9.613349380168E-2); -#10501=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.437502861023E-1)); -#10502=LINE('',#10501,#10500); -#10503=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#10504=VECTOR('',#10503,4.311571495761E-2); -#10505=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.0625E-1)); -#10506=LINE('',#10505,#10504); -#10507=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#10508=VECTOR('',#10507,5.671901268663E-2); -#10509=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,5.687497138977E-1)); -#10510=LINE('',#10509,#10508); -#10511=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#10512=VECTOR('',#10511,4.650081123436E-2); -#10513=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.5E-1)); -#10514=LINE('',#10513,#10512); -#10515=DIRECTION('',(1.E0,0.E0,0.E0)); -#10516=VECTOR('',#10515,8.510637283325E-2); -#10517=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,5.5E-1)); -#10518=LINE('',#10517,#10516); -#10519=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#10520=VECTOR('',#10519,9.300199582440E-2); -#10521=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.875002861023E-1)); -#10522=LINE('',#10521,#10520); -#10523=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#10524=VECTOR('',#10523,7.053251855852E-2); -#10525=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,6.437502861023E-1)); -#10526=LINE('',#10525,#10524); -#10527=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#10528=VECTOR('',#10527,1.144942942620E-1); -#10529=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,7.562502861023E-1)); -#10530=LINE('',#10529,#10528); -#10531=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10532=VECTOR('',#10531,7.499971389771E-2); -#10533=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,8.3125E-1)); -#10534=LINE('',#10533,#10532); -#10535=DIRECTION('',(1.E0,0.E0,0.E0)); -#10536=VECTOR('',#10535,8.510637283325E-2); -#10537=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,8.3125E-1)); -#10538=LINE('',#10537,#10536); -#10539=DIRECTION('',(0.E0,0.E0,1.E0)); -#10540=VECTOR('',#10539,7.499971389771E-2); -#10541=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,7.562502861023E-1)); -#10542=LINE('',#10541,#10540); -#10543=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#10544=VECTOR('',#10543,1.202789411086E-1); -#10545=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,6.437502861023E-1)); -#10546=LINE('',#10545,#10544); -#10547=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#10548=VECTOR('',#10547,5.671900150710E-2); -#10549=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,6.0625E-1)); -#10550=LINE('',#10549,#10548); -#10551=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#10552=VECTOR('',#10551,9.300196855221E-2); -#10553=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,5.687497138977E-1)); -#10554=LINE('',#10553,#10552); -#10555=DIRECTION('',(1.E0,0.E0,0.E0)); -#10556=VECTOR('',#10555,4.255324602127E-2); -#10557=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.687497138977E-1)); -#10558=LINE('',#10557,#10556); -#10559=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#10560=VECTOR('',#10559,7.403048172694E-2); -#10561=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.0625E-1)); -#10562=LINE('',#10561,#10560); -#10563=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#10564=VECTOR('',#10563,7.053251855852E-2); -#10565=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.625E-1)); -#10566=LINE('',#10565,#10564); -#10567=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#10568=VECTOR('',#10567,9.613433082315E-2); -#10569=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,7.562502861023E-1)); -#10570=LINE('',#10569,#10568); -#10571=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10572=VECTOR('',#10571,7.499971389771E-2); -#10573=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,8.3125E-1)); -#10574=LINE('',#10573,#10572); -#10575=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#10576=VECTOR('',#10575,9.613433082315E-2); -#10577=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.250002861023E-1)); -#10578=LINE('',#10577,#10576); -#10579=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#10580=VECTOR('',#10579,7.053251855852E-2); -#10581=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,9.812502861023E-1)); -#10582=LINE('',#10581,#10580); -#10583=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#10584=VECTOR('',#10583,7.403004695359E-2); -#10585=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.018749713898E0)); -#10586=LINE('',#10585,#10584); -#10587=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10588=VECTOR('',#10587,9.375028610230E-2); -#10589=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.1125E0)); -#10590=LINE('',#10589,#10588); -#10591=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#10592=VECTOR('',#10591,8.714726885037E-2); -#10593=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.093750286102E0)); -#10594=LINE('',#10593,#10592); -#10595=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#10596=VECTOR('',#10595,1.134380030142E-1); -#10597=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.018749713898E0)); -#10598=LINE('',#10597,#10596); -#10599=DIRECTION('',(4.934807975625E-1,0.E0,8.697566915162E-1)); -#10600=VECTOR('',#10599,8.623068339603E-2); -#10601=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.4375E-1)); -#10602=LINE('',#10601,#10600); -#10603=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#10604=VECTOR('',#10603,1.329630806532E-1); -#10605=CARTESIAN_POINT('',(4.75E0,1.5E0,8.125002861023E-1)); -#10606=LINE('',#10605,#10604); -#10607=DIRECTION('',(0.E0,0.E0,1.E0)); -#10608=VECTOR('',#10607,3.750028610229E-2); -#10609=CARTESIAN_POINT('',(4.75E0,1.5E0,7.75E-1)); -#10610=LINE('',#10609,#10608); -#10611=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#10612=VECTOR('',#10611,1.329630806532E-1); -#10613=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.437502861023E-1)); -#10614=LINE('',#10613,#10612); -#10615=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#10616=VECTOR('',#10615,8.623142991522E-2); -#10617=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,5.687497138977E-1)); -#10618=LINE('',#10617,#10616); -#10619=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#10620=VECTOR('',#10619,1.134374355386E-1); -#10621=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,4.9375E-1)); -#10622=LINE('',#10621,#10620); -#10623=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#10624=VECTOR('',#10623,8.714726885037E-2); -#10625=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,4.750002861023E-1)); -#10626=LINE('',#10625,#10624); -#10627=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10628=VECTOR('',#10627,4.255324602127E-2); -#10629=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,4.750002861023E-1)); -#10630=LINE('',#10629,#10628); -#10631=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#10632=VECTOR('',#10631,8.714726885037E-2); -#10633=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,4.9375E-1)); -#10634=LINE('',#10633,#10632); -#10635=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#10636=VECTOR('',#10635,7.403048172694E-2); -#10637=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.312502861023E-1)); -#10638=LINE('',#10637,#10636); -#10639=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#10640=VECTOR('',#10639,9.848450564280E-2); -#10641=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,6.0625E-1)); -#10642=LINE('',#10641,#10640); -#10643=DIRECTION('',(-4.133152317521E-1,0.E0,9.105880073896E-1)); -#10644=VECTOR('',#10643,1.029557663197E-1); -#10645=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,5.124997138977E-1)); -#10646=LINE('',#10645,#10644); -#10647=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#10648=VECTOR('',#10647,7.403004695359E-2); -#10649=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,4.750002861023E-1)); -#10650=LINE('',#10649,#10648); -#10651=DIRECTION('',(-9.765790138025E-1,0.E0,2.151590802187E-1)); -#10652=VECTOR('',#10651,8.714748262324E-2); -#10653=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,4.562497138977E-1)); -#10654=LINE('',#10653,#10652); -#10655=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10656=VECTOR('',#10655,8.510637283325E-2); -#10657=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,4.562497138977E-1)); -#10658=LINE('',#10657,#10656); -#10659=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#10660=VECTOR('',#10659,6.652688649895E-2); -#10661=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,4.750002861023E-1)); -#10662=LINE('',#10661,#10660); -#10663=DIRECTION('',(1.E0,0.E0,0.E0)); -#10664=VECTOR('',#10663,1.063829809427E-1); -#10665=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,3.062502861023E-1)); -#10666=LINE('',#10665,#10664); -#10667=DIRECTION('',(7.117174186007E-1,0.E0,7.024658824885E-1)); -#10668=VECTOR('',#10667,7.473680719479E-1); -#10669=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,-2.187502861023E-1)); -#10670=LINE('',#10669,#10668); -#10671=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#10672=VECTOR('',#10671,9.300162246873E-2); -#10673=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,-2.562497138977E-1)); -#10674=LINE('',#10673,#10672); -#10675=DIRECTION('',(1.E0,0.E0,0.E0)); -#10676=VECTOR('',#10675,4.255324602127E-2); -#10677=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,-2.562497138977E-1)); -#10678=LINE('',#10677,#10676); -#10679=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#10680=VECTOR('',#10679,7.403004695359E-2); -#10681=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,-2.187502861023E-1)); -#10682=LINE('',#10681,#10680); -#10683=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#10684=VECTOR('',#10683,7.053251855852E-2); -#10685=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,-1.625002861023E-1)); -#10686=LINE('',#10685,#10684); -#10687=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#10688=VECTOR('',#10687,9.613433082315E-2); -#10689=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,-6.875E-2)); -#10690=LINE('',#10689,#10688); -#10691=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10692=VECTOR('',#10691,7.499971389771E-2); -#10693=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,6.249713897704E-3)); -#10694=LINE('',#10693,#10692); -#10695=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#10696=VECTOR('',#10695,9.613433082315E-2); -#10697=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.E-1)); -#10698=LINE('',#10697,#10696); -#10699=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#10700=VECTOR('',#10699,7.053251855852E-2); -#10701=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,1.5625E-1)); -#10702=LINE('',#10701,#10700); -#10703=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#10704=VECTOR('',#10703,7.403048172694E-2); -#10705=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.937502861023E-1)); -#10706=LINE('',#10705,#10704); -#10707=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10708=VECTOR('',#10707,9.374942779541E-2); -#10709=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,2.874997138977E-1)); -#10710=LINE('',#10709,#10708); -#10711=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#10712=VECTOR('',#10711,8.714726885037E-2); -#10713=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,2.6875E-1)); -#10714=LINE('',#10713,#10712); -#10715=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#10716=VECTOR('',#10715,1.134374355386E-1); -#10717=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.937502861023E-1)); -#10718=LINE('',#10717,#10716); -#10719=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#10720=VECTOR('',#10719,8.623142991522E-2); -#10721=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.187497138977E-1)); -#10722=LINE('',#10721,#10720); -#10723=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#10724=VECTOR('',#10723,1.329630806532E-1); -#10725=CARTESIAN_POINT('',(4.75E0,1.5E0,-1.25E-2)); -#10726=LINE('',#10725,#10724); -#10727=DIRECTION('',(0.E0,0.E0,1.E0)); -#10728=VECTOR('',#10727,7.499971389771E-2); -#10729=CARTESIAN_POINT('',(4.75E0,1.5E0,-8.749971389771E-2)); -#10730=LINE('',#10729,#10728); -#10731=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#10732=VECTOR('',#10731,1.144942942620E-1); -#10733=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,-1.999997138977E-1)); -#10734=LINE('',#10733,#10732); -#10735=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#10736=VECTOR('',#10735,8.623142991522E-2); -#10737=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,-2.750002861023E-1)); -#10738=LINE('',#10737,#10736); -#10739=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#10740=VECTOR('',#10739,1.134374355386E-1); -#10741=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,-3.5E-1)); -#10742=LINE('',#10741,#10740); -#10743=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#10744=VECTOR('',#10743,8.714726885037E-2); -#10745=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,-3.687497138977E-1)); -#10746=LINE('',#10745,#10744); -#10747=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10748=VECTOR('',#10747,4.255324602127E-2); -#10749=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,-3.687497138977E-1)); -#10750=LINE('',#10749,#10748); -#10751=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#10752=VECTOR('',#10751,8.714726885037E-2); -#10753=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,-3.5E-1)); -#10754=LINE('',#10753,#10752); -#10755=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#10756=VECTOR('',#10755,7.403048172694E-2); -#10757=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,-3.124997138977E-1)); -#10758=LINE('',#10757,#10756); -#10759=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#10760=VECTOR('',#10759,6.624424131262E-1); -#10761=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.5625E-1)); -#10762=LINE('',#10761,#10760); -#10763=DIRECTION('',(0.E0,0.E0,1.E0)); -#10764=VECTOR('',#10763,5.249997138977E-1); -#10765=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,-3.687497138977E-1)); -#10766=LINE('',#10765,#10764); -#10767=DIRECTION('',(-1.E0,0.E0,0.E0)); -#10768=VECTOR('',#10767,1.063829809427E-1); -#10769=CARTESIAN_POINT('',(5.75E0,1.5E0,-3.687497138977E-1)); -#10770=LINE('',#10769,#10768); -#10771=DIRECTION('',(0.E0,0.E0,-1.E0)); -#10772=VECTOR('',#10771,6.75E-1); -#10773=CARTESIAN_POINT('',(5.75E0,1.5E0,3.062502861023E-1)); -#10774=LINE('',#10773,#10772); -#10775=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10776=VECTOR('',#10775,5.E-2); -#10777=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.830979256152E0)); -#10778=LINE('',#10777,#10776); -#10779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10780=VECTOR('',#10779,5.E-2); -#10781=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.830979256152E0)); -#10782=LINE('',#10781,#10780); -#10783=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10784=VECTOR('',#10783,5.E-2); -#10785=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.295746927498E0)); -#10786=LINE('',#10785,#10784); -#10787=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10788=VECTOR('',#10787,5.E-2); -#10789=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,8.211236555574E0)); -#10790=LINE('',#10789,#10788); -#10791=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10792=VECTOR('',#10791,5.E-2); -#10793=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,8.154896280760E0)); -#10794=LINE('',#10793,#10792); -#10795=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10796=VECTOR('',#10795,5.E-2); -#10797=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,8.126726183650E0)); -#10798=LINE('',#10797,#10796); -#10799=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10800=VECTOR('',#10799,5.E-2); -#10801=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,8.126726183650E0)); -#10802=LINE('',#10801,#10800); -#10803=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10804=VECTOR('',#10803,5.E-2); -#10805=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,8.154896280760E0)); -#10806=LINE('',#10805,#10804); -#10807=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10808=VECTOR('',#10807,5.E-2); -#10809=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,8.211236555574E0)); -#10810=LINE('',#10809,#10808); -#10811=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10812=VECTOR('',#10811,5.E-2); -#10813=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.295746927498E0)); -#10814=LINE('',#10813,#10812); -#10815=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10816=VECTOR('',#10815,5.E-2); -#10817=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,8.126726183650E0)); -#10818=LINE('',#10817,#10816); -#10819=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10820=VECTOR('',#10819,5.E-2); -#10821=CARTESIAN_POINT('',(1.234042525291E0,1.55E0,8.154896280760E0)); -#10822=LINE('',#10821,#10820); -#10823=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10824=VECTOR('',#10823,5.E-2); -#10825=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,8.211236555574E0)); -#10826=LINE('',#10825,#10824); -#10827=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10828=VECTOR('',#10827,5.E-2); -#10829=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.295746927498E0)); -#10830=LINE('',#10829,#10828); -#10831=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10832=VECTOR('',#10831,5.E-2); -#10833=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.830979256152E0)); -#10834=LINE('',#10833,#10832); -#10835=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10836=VECTOR('',#10835,5.E-2); -#10837=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.830979256152E0)); -#10838=LINE('',#10837,#10836); -#10839=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10840=VECTOR('',#10839,5.E-2); -#10841=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.295746927498E0)); -#10842=LINE('',#10841,#10840); -#10843=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10844=VECTOR('',#10843,5.E-2); -#10845=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,8.211236555574E0)); -#10846=LINE('',#10845,#10844); -#10847=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10848=VECTOR('',#10847,5.E-2); -#10849=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,8.154896280760E0)); -#10850=LINE('',#10849,#10848); -#10851=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10852=VECTOR('',#10851,5.E-2); -#10853=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,8.126726183650E0)); -#10854=LINE('',#10853,#10852); -#10855=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10856=VECTOR('',#10855,5.E-2); -#10857=CARTESIAN_POINT('',(0.E0,1.55E0,6.661879763833E0)); -#10858=LINE('',#10857,#10856); -#10859=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10860=VECTOR('',#10859,5.E-2); -#10861=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,6.661879763833E0)); -#10862=LINE('',#10861,#10860); -#10863=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10864=VECTOR('',#10863,5.E-2); -#10865=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.112601639967E0)); -#10866=LINE('',#10865,#10864); -#10867=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10868=VECTOR('',#10867,5.E-2); -#10869=CARTESIAN_POINT('',(2.E0,1.55E0,7.112601639967E0)); -#10870=LINE('',#10869,#10868); -#10871=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10872=VECTOR('',#10871,5.E-2); -#10873=CARTESIAN_POINT('',(2.E0,1.55E0,7.281622383815E0)); -#10874=LINE('',#10873,#10872); -#10875=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10876=VECTOR('',#10875,5.E-2); -#10877=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.281622383815E0)); -#10878=LINE('',#10877,#10876); -#10879=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10880=VECTOR('',#10879,5.E-2); -#10881=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.732344421140E0)); -#10882=LINE('',#10881,#10880); -#10883=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10884=VECTOR('',#10883,5.E-2); -#10885=CARTESIAN_POINT('',(0.E0,1.55E0,7.732344421140E0)); -#10886=LINE('',#10885,#10884); -#10887=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10888=VECTOR('',#10887,5.E-2); -#10889=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,6.211157726508E0)); -#10890=LINE('',#10889,#10888); -#10891=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#10892=VECTOR('',#10891,5.E-2); -#10893=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,6.267498081918E0)); -#10894=LINE('',#10893,#10892); -#10895=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10896=VECTOR('',#10895,5.E-2); -#10897=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,6.352008292651E0)); -#10898=LINE('',#10897,#10896); -#10899=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10900=VECTOR('',#10899,5.E-2); -#10901=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,6.408348648061E0)); -#10902=LINE('',#10901,#10900); -#10903=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10904=VECTOR('',#10903,5.E-2); -#10905=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.408348648061E0)); -#10906=LINE('',#10905,#10904); -#10907=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10908=VECTOR('',#10907,5.E-2); -#10909=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,6.352008292651E0)); -#10910=LINE('',#10909,#10908); -#10911=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#10912=VECTOR('',#10911,5.E-2); -#10913=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,6.267498081918E0)); -#10914=LINE('',#10913,#10912); -#10915=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10916=VECTOR('',#10915,5.E-2); -#10917=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,6.126647354584E0)); -#10918=LINE('',#10917,#10916); -#10919=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10920=VECTOR('',#10919,5.E-2); -#10921=CARTESIAN_POINT('',(0.E0,1.55E0,5.985796627250E0)); -#10922=LINE('',#10921,#10920); -#10923=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10924=VECTOR('',#10923,5.E-2); -#10925=CARTESIAN_POINT('',(0.E0,1.55E0,5.873116238812E0)); -#10926=LINE('',#10925,#10924); -#10927=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10928=VECTOR('',#10927,5.E-2); -#10929=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,5.732265511478E0)); -#10930=LINE('',#10929,#10928); -#10931=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10932=VECTOR('',#10931,5.E-2); -#10933=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,5.591415106526E0)); -#10934=LINE('',#10933,#10932); -#10935=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10936=VECTOR('',#10935,5.E-2); -#10937=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.506904734602E0)); -#10938=LINE('',#10937,#10936); -#10939=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10940=VECTOR('',#10939,5.E-2); -#10941=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.450564379192E0)); -#10942=LINE('',#10941,#10940); -#10943=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10944=VECTOR('',#10943,5.E-2); -#10945=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,5.450564379192E0)); -#10946=LINE('',#10945,#10944); -#10947=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10948=VECTOR('',#10947,5.E-2); -#10949=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,5.506904734602E0)); -#10950=LINE('',#10949,#10948); -#10951=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10952=VECTOR('',#10951,5.E-2); -#10953=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,5.591415106526E0)); -#10954=LINE('',#10953,#10952); -#10955=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#10956=VECTOR('',#10955,5.E-2); -#10957=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,5.647755139554E0)); -#10958=LINE('',#10957,#10956); -#10959=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10960=VECTOR('',#10959,5.E-2); -#10961=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,5.591415106526E0)); -#10962=LINE('',#10961,#10960); -#10963=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10964=VECTOR('',#10963,5.E-2); -#10965=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,5.478734395706E0)); -#10966=LINE('',#10965,#10964); -#10967=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10968=VECTOR('',#10967,5.E-2); -#10969=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.422394362678E0)); -#10970=LINE('',#10969,#10968); -#10971=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10972=VECTOR('',#10971,5.E-2); -#10973=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.422394362678E0)); -#10974=LINE('',#10973,#10972); -#10975=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10976=VECTOR('',#10975,5.E-2); -#10977=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,5.478734395706E0)); -#10978=LINE('',#10977,#10976); -#10979=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10980=VECTOR('',#10979,5.E-2); -#10981=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,5.563244767630E0)); -#10982=LINE('',#10981,#10980); -#10983=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10984=VECTOR('',#10983,5.E-2); -#10985=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,5.704095494964E0)); -#10986=LINE('',#10985,#10984); -#10987=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10988=VECTOR('',#10987,5.E-2); -#10989=CARTESIAN_POINT('',(2.E0,1.55E0,5.844946222298E0)); -#10990=LINE('',#10989,#10988); -#10991=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10992=VECTOR('',#10991,5.E-2); -#10993=CARTESIAN_POINT('',(2.E0,1.55E0,6.013966966146E0)); -#10994=LINE('',#10993,#10992); -#10995=DIRECTION('',(0.E0,-1.E0,0.E0)); -#10996=VECTOR('',#10995,5.E-2); -#10997=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,6.154817371098E0)); -#10998=LINE('',#10997,#10996); -#10999=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#11000=VECTOR('',#10999,5.E-2); -#11001=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,6.295668098432E0)); -#11002=LINE('',#11001,#11000); -#11003=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11004=VECTOR('',#11003,5.E-2); -#11005=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,6.380178470356E0)); -#11006=LINE('',#11005,#11004); -#11007=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11008=VECTOR('',#11007,5.E-2); -#11009=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.436518664575E0)); -#11010=LINE('',#11009,#11008); -#11011=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11012=VECTOR('',#11011,5.E-2); -#11013=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.436518664575E0)); -#11014=LINE('',#11013,#11012); -#11015=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11016=VECTOR('',#11015,5.E-2); -#11017=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,6.380178470356E0)); -#11018=LINE('',#11017,#11016); -#11019=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11020=VECTOR('',#11019,5.E-2); -#11021=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,6.267498081918E0)); -#11022=LINE('',#11021,#11020); -#11023=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11024=VECTOR('',#11023,5.E-2); -#11025=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.985796627250E0)); -#11026=LINE('',#11025,#11024); -#11027=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11028=VECTOR('',#11027,5.E-2); -#11029=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.873116238812E0)); -#11030=LINE('',#11029,#11028); -#11031=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11032=VECTOR('',#11031,5.E-2); -#11033=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,5.760435850374E0)); -#11034=LINE('',#11033,#11032); -#11035=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11036=VECTOR('',#11035,5.E-2); -#11037=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.647755139554E0)); -#11038=LINE('',#11037,#11036); -#11039=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11040=VECTOR('',#11039,5.E-2); -#11041=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.563244767630E0)); -#11042=LINE('',#11041,#11040); -#11043=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11044=VECTOR('',#11043,5.E-2); -#11045=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.563244767630E0)); -#11046=LINE('',#11045,#11044); -#11047=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11048=VECTOR('',#11047,5.E-2); -#11049=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,5.647755139554E0)); -#11050=LINE('',#11049,#11048); -#11051=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11052=VECTOR('',#11051,5.E-2); -#11053=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,5.760435850374E0)); -#11054=LINE('',#11053,#11052); -#11055=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11056=VECTOR('',#11055,5.E-2); -#11057=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.873116238812E0)); -#11058=LINE('',#11057,#11056); -#11059=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11060=VECTOR('',#11059,5.E-2); -#11061=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.985796627250E0)); -#11062=LINE('',#11061,#11060); -#11063=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11064=VECTOR('',#11063,5.E-2); -#11065=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,6.098477338070E0)); -#11066=LINE('',#11065,#11064); -#11067=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11068=VECTOR('',#11067,5.E-2); -#11069=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,6.211157726508E0)); -#11070=LINE('',#11069,#11068); -#11071=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11072=VECTOR('',#11071,5.E-2); -#11073=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.295668098432E0)); -#11074=LINE('',#11073,#11072); -#11075=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11076=VECTOR('',#11075,5.E-2); -#11077=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.295668098432E0)); -#11078=LINE('',#11077,#11076); -#11079=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11080=VECTOR('',#11079,5.E-2); -#11081=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,6.211157726508E0)); -#11082=LINE('',#11081,#11080); -#11083=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11084=VECTOR('',#11083,5.E-2); -#11085=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,6.098477338070E0)); -#11086=LINE('',#11085,#11084); -#11087=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11088=VECTOR('',#11087,5.E-2); -#11089=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.873116238812E0)); -#11090=LINE('',#11089,#11088); -#11091=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11092=VECTOR('',#11091,5.E-2); -#11093=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.985796627250E0)); -#11094=LINE('',#11093,#11092); -#11095=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11096=VECTOR('',#11095,5.E-2); -#11097=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,6.098477338070E0)); -#11098=LINE('',#11097,#11096); -#11099=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11100=VECTOR('',#11099,5.E-2); -#11101=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,6.211157726508E0)); -#11102=LINE('',#11101,#11100); -#11103=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11104=VECTOR('',#11103,5.E-2); -#11105=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.267498081918E0)); -#11106=LINE('',#11105,#11104); -#11107=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11108=VECTOR('',#11107,5.E-2); -#11109=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,6.267498081918E0)); -#11110=LINE('',#11109,#11108); -#11111=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11112=VECTOR('',#11111,5.E-2); -#11113=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,6.211157726508E0)); -#11114=LINE('',#11113,#11112); -#11115=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#11116=VECTOR('',#11115,5.E-2); -#11117=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,6.098477338070E0)); -#11118=LINE('',#11117,#11116); -#11119=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11120=VECTOR('',#11119,5.E-2); -#11121=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.985796627250E0)); -#11122=LINE('',#11121,#11120); -#11123=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11124=VECTOR('',#11123,5.E-2); -#11125=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.873116238812E0)); -#11126=LINE('',#11125,#11124); -#11127=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11128=VECTOR('',#11127,5.E-2); -#11129=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,5.760435850374E0)); -#11130=LINE('',#11129,#11128); -#11131=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11132=VECTOR('',#11131,5.E-2); -#11133=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,5.647755139554E0)); -#11134=LINE('',#11133,#11132); -#11135=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11136=VECTOR('',#11135,5.E-2); -#11137=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,5.591415106526E0)); -#11138=LINE('',#11137,#11136); -#11139=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11140=VECTOR('',#11139,5.E-2); -#11141=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.591415106526E0)); -#11142=LINE('',#11141,#11140); -#11143=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11144=VECTOR('',#11143,5.E-2); -#11145=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,5.647755139554E0)); -#11146=LINE('',#11145,#11144); -#11147=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11148=VECTOR('',#11147,5.E-2); -#11149=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,5.760435850374E0)); -#11150=LINE('',#11149,#11148); -#11151=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11152=VECTOR('',#11151,5.E-2); -#11153=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.267419172256E0)); -#11154=LINE('',#11153,#11152); -#11155=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11156=VECTOR('',#11155,5.E-2); -#11157=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,4.351929544180E0)); -#11158=LINE('',#11157,#11156); -#11159=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11160=VECTOR('',#11159,5.E-2); -#11161=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.464609932618E0)); -#11162=LINE('',#11161,#11160); -#11163=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11164=VECTOR('',#11163,5.E-2); -#11165=CARTESIAN_POINT('',(2.E0,1.55E0,4.577290643438E0)); -#11166=LINE('',#11165,#11164); -#11167=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11168=VECTOR('',#11167,5.E-2); -#11169=CARTESIAN_POINT('',(2.E0,1.55E0,4.802651420314E0)); -#11170=LINE('',#11169,#11168); -#11171=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11172=VECTOR('',#11171,5.E-2); -#11173=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.915332131134E0)); -#11174=LINE('',#11173,#11172); -#11175=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11176=VECTOR('',#11175,5.E-2); -#11177=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,5.028012519572E0)); -#11178=LINE('',#11177,#11176); -#11179=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11180=VECTOR('',#11179,5.E-2); -#11181=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.112522891496E0)); -#11182=LINE('',#11181,#11180); -#11183=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11184=VECTOR('',#11183,5.E-2); -#11185=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.168863246906E0)); -#11186=LINE('',#11185,#11184); -#11187=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11188=VECTOR('',#11187,5.E-2); -#11189=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.197033263420E0)); -#11190=LINE('',#11189,#11188); -#11191=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11192=VECTOR('',#11191,5.E-2); -#11193=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.056182536086E0)); -#11194=LINE('',#11193,#11192); -#11195=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11196=VECTOR('',#11195,5.E-2); -#11197=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,5.028012519572E0)); -#11198=LINE('',#11197,#11196); -#11199=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11200=VECTOR('',#11199,5.E-2); -#11201=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.971672164162E0)); -#11202=LINE('',#11201,#11200); -#11203=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11204=VECTOR('',#11203,5.E-2); -#11205=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.915332131134E0)); -#11206=LINE('',#11205,#11204); -#11207=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11208=VECTOR('',#11207,5.E-2); -#11209=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.774481403800E0)); -#11210=LINE('',#11209,#11208); -#11211=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11212=VECTOR('',#11211,5.E-2); -#11213=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.605460659952E0)); -#11214=LINE('',#11213,#11212); -#11215=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11216=VECTOR('',#11215,5.E-2); -#11217=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.464609932618E0)); -#11218=LINE('',#11217,#11216); -#11219=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#11220=VECTOR('',#11219,5.E-2); -#11221=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.408269899590E0)); -#11222=LINE('',#11221,#11220); -#11223=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11224=VECTOR('',#11223,5.E-2); -#11225=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,4.351929544180E0)); -#11226=LINE('',#11225,#11224); -#11227=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11228=VECTOR('',#11227,5.E-2); -#11229=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.323759527666E0)); -#11230=LINE('',#11229,#11228); -#11231=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11232=VECTOR('',#11231,5.E-2); -#11233=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.323759527666E0)); -#11234=LINE('',#11233,#11232); -#11235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11236=VECTOR('',#11235,5.E-2); -#11237=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.380099560694E0)); -#11238=LINE('',#11237,#11236); -#11239=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11240=VECTOR('',#11239,5.E-2); -#11241=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,4.464609932618E0)); -#11242=LINE('',#11241,#11240); -#11243=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11244=VECTOR('',#11243,5.E-2); -#11245=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.633630676466E0)); -#11246=LINE('',#11245,#11244); -#11247=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11248=VECTOR('',#11247,5.E-2); -#11249=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.746311387286E0)); -#11250=LINE('',#11249,#11248); -#11251=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11252=VECTOR('',#11251,5.E-2); -#11253=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.746311387286E0)); -#11254=LINE('',#11253,#11252); -#11255=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11256=VECTOR('',#11255,5.E-2); -#11257=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.633630676466E0)); -#11258=LINE('',#11257,#11256); -#11259=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11260=VECTOR('',#11259,5.E-2); -#11261=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,4.464609932618E0)); -#11262=LINE('',#11261,#11260); -#11263=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11264=VECTOR('',#11263,5.E-2); -#11265=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.408269899590E0)); -#11266=LINE('',#11265,#11264); -#11267=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11268=VECTOR('',#11267,5.E-2); -#11269=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.351929544180E0)); -#11270=LINE('',#11269,#11268); -#11271=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11272=VECTOR('',#11271,5.E-2); -#11273=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.351929544180E0)); -#11274=LINE('',#11273,#11272); -#11275=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11276=VECTOR('',#11275,5.E-2); -#11277=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.408269899590E0)); -#11278=LINE('',#11277,#11276); -#11279=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11280=VECTOR('',#11279,5.E-2); -#11281=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.492780271514E0)); -#11282=LINE('',#11281,#11280); -#11283=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11284=VECTOR('',#11283,5.E-2); -#11285=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.633630676466E0)); -#11286=LINE('',#11285,#11284); -#11287=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11288=VECTOR('',#11287,5.E-2); -#11289=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.746311387286E0)); -#11290=LINE('',#11289,#11288); -#11291=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11292=VECTOR('',#11291,5.E-2); -#11293=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.887161792238E0)); -#11294=LINE('',#11293,#11292); -#11295=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11296=VECTOR('',#11295,5.E-2); -#11297=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.971672164162E0)); -#11298=LINE('',#11297,#11296); -#11299=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#11300=VECTOR('',#11299,5.E-2); -#11301=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.028012519572E0)); -#11302=LINE('',#11301,#11300); -#11303=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11304=VECTOR('',#11303,5.E-2); -#11305=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.168863246906E0)); -#11306=LINE('',#11305,#11304); -#11307=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11308=VECTOR('',#11307,5.E-2); -#11309=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.140692908010E0)); -#11310=LINE('',#11309,#11308); -#11311=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11312=VECTOR('',#11311,5.E-2); -#11313=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,5.028012519572E0)); -#11314=LINE('',#11313,#11312); -#11315=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11316=VECTOR('',#11315,5.E-2); -#11317=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.915332131134E0)); -#11318=LINE('',#11317,#11316); -#11319=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11320=VECTOR('',#11319,5.E-2); -#11321=CARTESIAN_POINT('',(0.E0,1.55E0,4.718141048390E0)); -#11322=LINE('',#11321,#11320); -#11323=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11324=VECTOR('',#11323,5.E-2); -#11325=CARTESIAN_POINT('',(0.E0,1.55E0,4.661801015362E0)); -#11326=LINE('',#11325,#11324); -#11327=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11328=VECTOR('',#11327,5.E-2); -#11329=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.464609932618E0)); -#11330=LINE('',#11329,#11328); -#11331=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11332=VECTOR('',#11331,5.E-2); -#11333=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,4.351929544180E0)); -#11334=LINE('',#11333,#11332); -#11335=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11336=VECTOR('',#11335,5.E-2); -#11337=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,4.239249155742E0)); -#11338=LINE('',#11337,#11336); -#11339=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11340=VECTOR('',#11339,5.E-2); -#11341=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.211078816846E0)); -#11342=LINE('',#11341,#11340); -#11343=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11344=VECTOR('',#11343,5.E-2); -#11345=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.211078816846E0)); -#11346=LINE('',#11345,#11344); -#11347=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11348=VECTOR('',#11347,5.E-2); -#11349=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.239249155742E0)); -#11350=LINE('',#11349,#11348); -#11351=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#11352=VECTOR('',#11351,5.E-2); -#11353=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,4.295589188770E0)); -#11354=LINE('',#11353,#11352); -#11355=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11356=VECTOR('',#11355,5.E-2); -#11357=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,4.408269899590E0)); -#11358=LINE('',#11357,#11356); -#11359=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11360=VECTOR('',#11359,5.E-2); -#11361=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.267419172256E0)); -#11362=LINE('',#11361,#11360); -#11363=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11364=VECTOR('',#11363,5.E-2); -#11365=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.211078816846E0)); -#11366=LINE('',#11365,#11364); -#11367=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11368=VECTOR('',#11367,5.E-2); -#11369=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.182908800332E0)); -#11370=LINE('',#11369,#11368); -#11371=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11372=VECTOR('',#11371,5.E-2); -#11373=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.182908800332E0)); -#11374=LINE('',#11373,#11372); -#11375=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11376=VECTOR('',#11375,5.E-2); -#11377=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,4.211078816846E0)); -#11378=LINE('',#11377,#11376); -#11379=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11380=VECTOR('',#11379,5.E-2); -#11381=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.957547701074E0)); -#11382=LINE('',#11381,#11380); -#11383=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11384=VECTOR('',#11383,5.E-2); -#11385=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,3.168784337244E0)); -#11386=LINE('',#11385,#11384); -#11387=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11388=VECTOR('',#11387,5.E-2); -#11389=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,3.112444304216E0)); -#11390=LINE('',#11389,#11388); -#11391=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11392=VECTOR('',#11391,5.E-2); -#11393=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.112444304216E0)); -#11394=LINE('',#11393,#11392); -#11395=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11396=VECTOR('',#11395,5.E-2); -#11397=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.168784337244E0)); -#11398=LINE('',#11397,#11396); -#11399=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11400=VECTOR('',#11399,5.E-2); -#11401=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.253294709168E0)); -#11402=LINE('',#11401,#11400); -#11403=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11404=VECTOR('',#11403,5.E-2); -#11405=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.394145114120E0)); -#11406=LINE('',#11405,#11404); -#11407=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11408=VECTOR('',#11407,5.E-2); -#11409=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.506825824940E0)); -#11410=LINE('',#11409,#11408); -#11411=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11412=VECTOR('',#11411,5.E-2); -#11413=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.647676552274E0)); -#11414=LINE('',#11413,#11412); -#11415=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11416=VECTOR('',#11415,5.E-2); -#11417=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.732186924198E0)); -#11418=LINE('',#11417,#11416); -#11419=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11420=VECTOR('',#11419,5.E-2); -#11421=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.788526957226E0)); -#11422=LINE('',#11421,#11420); -#11423=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11424=VECTOR('',#11423,5.E-2); -#11425=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.929377684560E0)); -#11426=LINE('',#11425,#11424); -#11427=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11428=VECTOR('',#11427,5.E-2); -#11429=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,3.901207668046E0)); -#11430=LINE('',#11429,#11428); -#11431=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11432=VECTOR('',#11431,5.E-2); -#11433=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.788526957226E0)); -#11434=LINE('',#11433,#11432); -#11435=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11436=VECTOR('',#11435,5.E-2); -#11437=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.675846568788E0)); -#11438=LINE('',#11437,#11436); -#11439=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11440=VECTOR('',#11439,5.E-2); -#11441=CARTESIAN_POINT('',(0.E0,1.55E0,3.478655486044E0)); -#11442=LINE('',#11441,#11440); -#11443=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11444=VECTOR('',#11443,5.E-2); -#11445=CARTESIAN_POINT('',(0.E0,1.55E0,3.365975419988E0)); -#11446=LINE('',#11445,#11444); -#11447=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11448=VECTOR('',#11447,5.E-2); -#11449=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.196954676140E0)); -#11450=LINE('',#11449,#11448); -#11451=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11452=VECTOR('',#11451,5.E-2); -#11453=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.084273965320E0)); -#11454=LINE('',#11453,#11452); -#11455=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11456=VECTOR('',#11455,5.E-2); -#11457=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,2.971593254501E0)); -#11458=LINE('',#11457,#11456); -#11459=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11460=VECTOR('',#11459,5.E-2); -#11461=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,2.943423560368E0)); -#11462=LINE('',#11461,#11460); -#11463=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11464=VECTOR('',#11463,5.E-2); -#11465=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,2.943423560368E0)); -#11466=LINE('',#11465,#11464); -#11467=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11468=VECTOR('',#11467,5.E-2); -#11469=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,2.971593254501E0)); -#11470=LINE('',#11469,#11468); -#11471=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11472=VECTOR('',#11471,5.E-2); -#11473=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,3.027933932292E0)); -#11474=LINE('',#11473,#11472); -#11475=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11476=VECTOR('',#11475,5.E-2); -#11477=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.732186924198E0)); -#11478=LINE('',#11477,#11476); -#11479=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11480=VECTOR('',#11479,5.E-2); -#11481=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,2.943423560368E0)); -#11482=LINE('',#11481,#11480); -#11483=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11484=VECTOR('',#11483,5.E-2); -#11485=CARTESIAN_POINT('',(2.E0,1.55E0,2.943423560368E0)); -#11486=LINE('',#11485,#11484); -#11487=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11488=VECTOR('',#11487,5.E-2); -#11489=CARTESIAN_POINT('',(2.E0,1.55E0,3.957547701074E0)); -#11490=LINE('',#11489,#11488); -#11491=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11492=VECTOR('',#11491,5.E-2); -#11493=CARTESIAN_POINT('',(2.E0,1.55E0,1.760278353432E0)); -#11494=LINE('',#11493,#11492); -#11495=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11496=VECTOR('',#11495,5.E-2); -#11497=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,2.154659874156E0)); -#11498=LINE('',#11497,#11496); -#11499=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11500=VECTOR('',#11499,5.E-2); -#11501=CARTESIAN_POINT('',(2.E0,1.55E0,2.549041394881E0)); -#11502=LINE('',#11501,#11500); -#11503=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11504=VECTOR('',#11503,5.E-2); -#11505=CARTESIAN_POINT('',(2.E0,1.55E0,2.718062138729E0)); -#11506=LINE('',#11505,#11504); -#11507=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11508=VECTOR('',#11507,5.E-2); -#11509=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.239170246080E0)); -#11510=LINE('',#11509,#11508); -#11511=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11512=VECTOR('',#11511,5.E-2); -#11513=CARTESIAN_POINT('',(0.E0,1.55E0,2.718062138729E0)); -#11514=LINE('',#11513,#11512); -#11515=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11516=VECTOR('',#11515,5.E-2); -#11517=CARTESIAN_POINT('',(0.E0,1.55E0,2.549041394881E0)); -#11518=LINE('',#11517,#11516); -#11519=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11520=VECTOR('',#11519,5.E-2); -#11521=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,2.154659874156E0)); -#11522=LINE('',#11521,#11520); -#11523=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11524=VECTOR('',#11523,5.E-2); -#11525=CARTESIAN_POINT('',(0.E0,1.55E0,1.760278353432E0)); -#11526=LINE('',#11525,#11524); -#11527=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11528=VECTOR('',#11527,5.E-2); -#11529=CARTESIAN_POINT('',(0.E0,1.55E0,1.591257609584E0)); -#11530=LINE('',#11529,#11528); -#11531=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11532=VECTOR('',#11531,5.E-2); -#11533=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.070149502232E0)); -#11534=LINE('',#11533,#11532); -#11535=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11536=VECTOR('',#11535,5.E-2); -#11537=CARTESIAN_POINT('',(2.E0,1.55E0,1.591257609584E0)); -#11538=LINE('',#11537,#11536); -#11539=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11540=VECTOR('',#11539,5.E-2); -#11541=CARTESIAN_POINT('',(4.E0,1.55E0,1.03375E1)); -#11542=LINE('',#11541,#11540); -#11543=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11544=VECTOR('',#11543,5.E-2); -#11545=CARTESIAN_POINT('',(4.E0,1.55E0,1.045E1)); -#11546=LINE('',#11545,#11544); -#11547=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11548=VECTOR('',#11547,5.E-2); -#11549=CARTESIAN_POINT('',(3.E0,1.55E0,1.045E1)); -#11550=LINE('',#11549,#11548); -#11551=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11552=VECTOR('',#11551,5.E-2); -#11553=CARTESIAN_POINT('',(3.E0,1.55E0,9.775E0)); -#11554=LINE('',#11553,#11552); -#11555=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11556=VECTOR('',#11555,5.E-2); -#11557=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.775E0)); -#11558=LINE('',#11557,#11556); -#11559=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11560=VECTOR('',#11559,5.E-2); -#11561=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.03375E1)); -#11562=LINE('',#11561,#11560); -#11563=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11564=VECTOR('',#11563,5.E-2); -#11565=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.03375E1)); -#11566=LINE('',#11565,#11564); -#11567=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11568=VECTOR('',#11567,5.E-2); -#11569=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,9.849999982119E0)); -#11570=LINE('',#11569,#11568); -#11571=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11572=VECTOR('',#11571,5.E-2); -#11573=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,9.849999982119E0)); -#11574=LINE('',#11573,#11572); -#11575=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11576=VECTOR('',#11575,5.E-2); -#11577=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.03375E1)); -#11578=LINE('',#11577,#11576); -#11579=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11580=VECTOR('',#11579,5.E-2); -#11581=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.893750035763E0)); -#11582=LINE('',#11581,#11580); -#11583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11584=VECTOR('',#11583,5.E-2); -#11585=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.912499964237E0)); -#11586=LINE('',#11585,#11584); -#11587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11588=VECTOR('',#11587,5.E-2); -#11589=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.9875E0)); -#11590=LINE('',#11589,#11588); -#11591=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11592=VECTOR('',#11591,5.E-2); -#11593=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.062500035763E0)); -#11594=LINE('',#11593,#11592); -#11595=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11596=VECTOR('',#11595,5.E-2); -#11597=CARTESIAN_POINT('',(4.E0,1.55E0,9.15625E0)); -#11598=LINE('',#11597,#11596); -#11599=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11600=VECTOR('',#11599,5.E-2); -#11601=CARTESIAN_POINT('',(4.E0,1.55E0,9.325E0)); -#11602=LINE('',#11601,#11600); -#11603=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11604=VECTOR('',#11603,5.E-2); -#11605=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.418749964237E0)); -#11606=LINE('',#11605,#11604); -#11607=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11608=VECTOR('',#11607,5.E-2); -#11609=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,9.49375E0)); -#11610=LINE('',#11609,#11608); -#11611=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11612=VECTOR('',#11611,5.E-2); -#11613=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.568749982119E0)); -#11614=LINE('',#11613,#11612); -#11615=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11616=VECTOR('',#11615,5.E-2); -#11617=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,9.60625E0)); -#11618=LINE('',#11617,#11616); -#11619=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11620=VECTOR('',#11619,5.E-2); -#11621=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.624999982119E0)); -#11622=LINE('',#11621,#11620); -#11623=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11624=VECTOR('',#11623,5.E-2); -#11625=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.624999982119E0)); -#11626=LINE('',#11625,#11624); -#11627=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11628=VECTOR('',#11627,5.E-2); -#11629=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,9.60625E0)); -#11630=LINE('',#11629,#11628); -#11631=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11632=VECTOR('',#11631,5.E-2); -#11633=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.568749982119E0)); -#11634=LINE('',#11633,#11632); -#11635=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11636=VECTOR('',#11635,5.E-2); -#11637=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,9.49375E0)); -#11638=LINE('',#11637,#11636); -#11639=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11640=VECTOR('',#11639,5.E-2); -#11641=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.418749964237E0)); -#11642=LINE('',#11641,#11640); -#11643=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11644=VECTOR('',#11643,5.E-2); -#11645=CARTESIAN_POINT('',(3.E0,1.55E0,9.325E0)); -#11646=LINE('',#11645,#11644); -#11647=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11648=VECTOR('',#11647,5.E-2); -#11649=CARTESIAN_POINT('',(3.E0,1.55E0,9.15625E0)); -#11650=LINE('',#11649,#11648); -#11651=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11652=VECTOR('',#11651,5.E-2); -#11653=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.062500035763E0)); -#11654=LINE('',#11653,#11652); -#11655=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11656=VECTOR('',#11655,5.E-2); -#11657=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.9875E0)); -#11658=LINE('',#11657,#11656); -#11659=DIRECTION('',(2.664535259100E-14,-1.E0,0.E0)); -#11660=VECTOR('',#11659,5.E-2); -#11661=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.912499964237E0)); -#11662=LINE('',#11661,#11660); -#11663=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11664=VECTOR('',#11663,5.E-2); -#11665=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.893750035763E0)); -#11666=LINE('',#11665,#11664); -#11667=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11668=VECTOR('',#11667,5.E-2); -#11669=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.006250035763E0)); -#11670=LINE('',#11669,#11668); -#11671=DIRECTION('',(-5.329070518201E-14,-1.E0,0.E0)); -#11672=VECTOR('',#11671,5.E-2); -#11673=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.024999964237E0)); -#11674=LINE('',#11673,#11672); -#11675=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11676=VECTOR('',#11675,5.E-2); -#11677=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.081249964237E0)); -#11678=LINE('',#11677,#11676); -#11679=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11680=VECTOR('',#11679,5.E-2); -#11681=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.15625E0)); -#11682=LINE('',#11681,#11680); -#11683=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11684=VECTOR('',#11683,5.E-2); -#11685=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.325E0)); -#11686=LINE('',#11685,#11684); -#11687=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11688=VECTOR('',#11687,5.E-2); -#11689=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.400000035763E0)); -#11690=LINE('',#11689,#11688); -#11691=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11692=VECTOR('',#11691,5.E-2); -#11693=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.456250035763E0)); -#11694=LINE('',#11693,#11692); -#11695=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11696=VECTOR('',#11695,5.E-2); -#11697=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.49375E0)); -#11698=LINE('',#11697,#11696); -#11699=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11700=VECTOR('',#11699,5.E-2); -#11701=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.512500035763E0)); -#11702=LINE('',#11701,#11700); -#11703=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11704=VECTOR('',#11703,5.E-2); -#11705=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.512500035763E0)); -#11706=LINE('',#11705,#11704); -#11707=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#11708=VECTOR('',#11707,5.E-2); -#11709=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.49375E0)); -#11710=LINE('',#11709,#11708); -#11711=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11712=VECTOR('',#11711,5.E-2); -#11713=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.456250035763E0)); -#11714=LINE('',#11713,#11712); -#11715=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11716=VECTOR('',#11715,5.E-2); -#11717=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.400000035763E0)); -#11718=LINE('',#11717,#11716); -#11719=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11720=VECTOR('',#11719,5.E-2); -#11721=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.325E0)); -#11722=LINE('',#11721,#11720); -#11723=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11724=VECTOR('',#11723,5.E-2); -#11725=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.15625E0)); -#11726=LINE('',#11725,#11724); -#11727=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11728=VECTOR('',#11727,5.E-2); -#11729=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.081249964237E0)); -#11730=LINE('',#11729,#11728); -#11731=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11732=VECTOR('',#11731,5.E-2); -#11733=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.024999964237E0)); -#11734=LINE('',#11733,#11732); -#11735=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11736=VECTOR('',#11735,5.E-2); -#11737=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.006250035763E0)); -#11738=LINE('',#11737,#11736); -#11739=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11740=VECTOR('',#11739,5.E-2); -#11741=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.012500071526E0)); -#11742=LINE('',#11741,#11740); -#11743=DIRECTION('',(2.664535259100E-14,-1.E0,0.E0)); -#11744=VECTOR('',#11743,5.E-2); -#11745=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.03125E0)); -#11746=LINE('',#11745,#11744); -#11747=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11748=VECTOR('',#11747,5.E-2); -#11749=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.106249928474E0)); -#11750=LINE('',#11749,#11748); -#11751=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11752=VECTOR('',#11751,5.E-2); -#11753=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.181250071526E0)); -#11754=LINE('',#11753,#11752); -#11755=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11756=VECTOR('',#11755,5.E-2); -#11757=CARTESIAN_POINT('',(4.E0,1.55E0,8.274999928474E0)); -#11758=LINE('',#11757,#11756); -#11759=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11760=VECTOR('',#11759,5.E-2); -#11761=CARTESIAN_POINT('',(4.E0,1.55E0,8.443749928474E0)); -#11762=LINE('',#11761,#11760); -#11763=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11764=VECTOR('',#11763,5.E-2); -#11765=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.5375E0)); -#11766=LINE('',#11765,#11764); -#11767=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11768=VECTOR('',#11767,5.E-2); -#11769=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.612499928474E0)); -#11770=LINE('',#11769,#11768); -#11771=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11772=VECTOR('',#11771,5.E-2); -#11773=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.687499964237E0)); -#11774=LINE('',#11773,#11772); -#11775=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11776=VECTOR('',#11775,5.E-2); -#11777=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,8.725000035763E0)); -#11778=LINE('',#11777,#11776); -#11779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11780=VECTOR('',#11779,5.E-2); -#11781=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.743749964237E0)); -#11782=LINE('',#11781,#11780); -#11783=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11784=VECTOR('',#11783,5.E-2); -#11785=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.743749964237E0)); -#11786=LINE('',#11785,#11784); -#11787=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#11788=VECTOR('',#11787,5.E-2); -#11789=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,8.725000035763E0)); -#11790=LINE('',#11789,#11788); -#11791=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11792=VECTOR('',#11791,5.E-2); -#11793=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.687499964237E0)); -#11794=LINE('',#11793,#11792); -#11795=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11796=VECTOR('',#11795,5.E-2); -#11797=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.612499928474E0)); -#11798=LINE('',#11797,#11796); -#11799=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11800=VECTOR('',#11799,5.E-2); -#11801=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.5375E0)); -#11802=LINE('',#11801,#11800); -#11803=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11804=VECTOR('',#11803,5.E-2); -#11805=CARTESIAN_POINT('',(3.E0,1.55E0,8.443749928474E0)); -#11806=LINE('',#11805,#11804); -#11807=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11808=VECTOR('',#11807,5.E-2); -#11809=CARTESIAN_POINT('',(3.E0,1.55E0,8.274999928474E0)); -#11810=LINE('',#11809,#11808); -#11811=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11812=VECTOR('',#11811,5.E-2); -#11813=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.181250071526E0)); -#11814=LINE('',#11813,#11812); -#11815=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11816=VECTOR('',#11815,5.E-2); -#11817=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.106249928474E0)); -#11818=LINE('',#11817,#11816); -#11819=DIRECTION('',(-1.776356839400E-14,-1.E0,0.E0)); -#11820=VECTOR('',#11819,5.E-2); -#11821=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.03125E0)); -#11822=LINE('',#11821,#11820); -#11823=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11824=VECTOR('',#11823,5.E-2); -#11825=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.012500071526E0)); -#11826=LINE('',#11825,#11824); -#11827=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11828=VECTOR('',#11827,5.E-2); -#11829=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.125000071526E0)); -#11830=LINE('',#11829,#11828); -#11831=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11832=VECTOR('',#11831,5.E-2); -#11833=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.14375E0)); -#11834=LINE('',#11833,#11832); -#11835=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11836=VECTOR('',#11835,5.E-2); -#11837=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.2E0)); -#11838=LINE('',#11837,#11836); -#11839=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11840=VECTOR('',#11839,5.E-2); -#11841=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.274999928474E0)); -#11842=LINE('',#11841,#11840); -#11843=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11844=VECTOR('',#11843,5.E-2); -#11845=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.443749928474E0)); -#11846=LINE('',#11845,#11844); -#11847=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11848=VECTOR('',#11847,5.E-2); -#11849=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.518750071526E0)); -#11850=LINE('',#11849,#11848); -#11851=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11852=VECTOR('',#11851,5.E-2); -#11853=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.575000071526E0)); -#11854=LINE('',#11853,#11852); -#11855=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11856=VECTOR('',#11855,5.E-2); -#11857=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.612499928474E0)); -#11858=LINE('',#11857,#11856); -#11859=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11860=VECTOR('',#11859,5.E-2); -#11861=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.631250071526E0)); -#11862=LINE('',#11861,#11860); -#11863=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11864=VECTOR('',#11863,5.E-2); -#11865=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.631250071526E0)); -#11866=LINE('',#11865,#11864); -#11867=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11868=VECTOR('',#11867,5.E-2); -#11869=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.612499928474E0)); -#11870=LINE('',#11869,#11868); -#11871=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11872=VECTOR('',#11871,5.E-2); -#11873=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.575000071526E0)); -#11874=LINE('',#11873,#11872); -#11875=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11876=VECTOR('',#11875,5.E-2); -#11877=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.518750071526E0)); -#11878=LINE('',#11877,#11876); -#11879=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11880=VECTOR('',#11879,5.E-2); -#11881=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.443749928474E0)); -#11882=LINE('',#11881,#11880); -#11883=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11884=VECTOR('',#11883,5.E-2); -#11885=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.274999928474E0)); -#11886=LINE('',#11885,#11884); -#11887=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11888=VECTOR('',#11887,5.E-2); -#11889=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.2E0)); -#11890=LINE('',#11889,#11888); -#11891=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11892=VECTOR('',#11891,5.E-2); -#11893=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.14375E0)); -#11894=LINE('',#11893,#11892); -#11895=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11896=VECTOR('',#11895,5.E-2); -#11897=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.125000071526E0)); -#11898=LINE('',#11897,#11896); -#11899=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11900=VECTOR('',#11899,5.E-2); -#11901=CARTESIAN_POINT('',(4.E0,1.55E0,7.75E0)); -#11902=LINE('',#11901,#11900); -#11903=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11904=VECTOR('',#11903,5.E-2); -#11905=CARTESIAN_POINT('',(4.E0,1.55E0,7.8625E0)); -#11906=LINE('',#11905,#11904); -#11907=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11908=VECTOR('',#11907,5.E-2); -#11909=CARTESIAN_POINT('',(3.E0,1.55E0,7.8625E0)); -#11910=LINE('',#11909,#11908); -#11911=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11912=VECTOR('',#11911,5.E-2); -#11913=CARTESIAN_POINT('',(3.E0,1.55E0,7.75E0)); -#11914=LINE('',#11913,#11912); -#11915=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11916=VECTOR('',#11915,5.E-2); -#11917=CARTESIAN_POINT('',(3.E0,1.55E0,7.149999928474E0)); -#11918=LINE('',#11917,#11916); -#11919=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11920=VECTOR('',#11919,5.E-2); -#11921=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,7.056250071526E0)); -#11922=LINE('',#11921,#11920); -#11923=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11924=VECTOR('',#11923,5.E-2); -#11925=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,6.981249928474E0)); -#11926=LINE('',#11925,#11924); -#11927=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11928=VECTOR('',#11927,5.E-2); -#11929=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,6.90625E0)); -#11930=LINE('',#11929,#11928); -#11931=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11932=VECTOR('',#11931,5.E-2); -#11933=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,6.868749928474E0)); -#11934=LINE('',#11933,#11932); -#11935=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11936=VECTOR('',#11935,5.E-2); -#11937=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.85E0)); -#11938=LINE('',#11937,#11936); -#11939=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11940=VECTOR('',#11939,5.E-2); -#11941=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.85E0)); -#11942=LINE('',#11941,#11940); -#11943=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11944=VECTOR('',#11943,5.E-2); -#11945=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,6.868749928474E0)); -#11946=LINE('',#11945,#11944); -#11947=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#11948=VECTOR('',#11947,5.E-2); -#11949=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.90625E0)); -#11950=LINE('',#11949,#11948); -#11951=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#11952=VECTOR('',#11951,5.E-2); -#11953=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,6.981249928474E0)); -#11954=LINE('',#11953,#11952); -#11955=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11956=VECTOR('',#11955,5.E-2); -#11957=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,7.056250071526E0)); -#11958=LINE('',#11957,#11956); -#11959=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#11960=VECTOR('',#11959,5.E-2); -#11961=CARTESIAN_POINT('',(4.E0,1.55E0,7.149999928474E0)); -#11962=LINE('',#11961,#11960); -#11963=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11964=VECTOR('',#11963,5.E-2); -#11965=CARTESIAN_POINT('',(4.E0,1.55E0,7.599999928474E0)); -#11966=LINE('',#11965,#11964); -#11967=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11968=VECTOR('',#11967,5.E-2); -#11969=CARTESIAN_POINT('',(3.E0,1.55E0,7.599999928474E0)); -#11970=LINE('',#11969,#11968); -#11971=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11972=VECTOR('',#11971,5.E-2); -#11973=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.487499928474E0)); -#11974=LINE('',#11973,#11972); -#11975=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11976=VECTOR('',#11975,5.E-2); -#11977=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.487499928474E0)); -#11978=LINE('',#11977,#11976); -#11979=DIRECTION('',(0.E0,-1.E0,5.329070518201E-14)); -#11980=VECTOR('',#11979,5.E-2); -#11981=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.149999928474E0)); -#11982=LINE('',#11981,#11980); -#11983=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11984=VECTOR('',#11983,5.E-2); -#11985=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,7.075E0)); -#11986=LINE('',#11985,#11984); -#11987=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11988=VECTOR('',#11987,5.E-2); -#11989=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,7.01875E0)); -#11990=LINE('',#11989,#11988); -#11991=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11992=VECTOR('',#11991,5.E-2); -#11993=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,6.981249928474E0)); -#11994=LINE('',#11993,#11992); -#11995=DIRECTION('',(0.E0,-1.E0,0.E0)); -#11996=VECTOR('',#11995,5.E-2); -#11997=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.9625E0)); -#11998=LINE('',#11997,#11996); -#11999=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12000=VECTOR('',#11999,5.E-2); -#12001=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.9625E0)); -#12002=LINE('',#12001,#12000); -#12003=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12004=VECTOR('',#12003,5.E-2); -#12005=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,6.981249928474E0)); -#12006=LINE('',#12005,#12004); -#12007=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12008=VECTOR('',#12007,5.E-2); -#12009=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,7.01875E0)); -#12010=LINE('',#12009,#12008); -#12011=DIRECTION('',(0.E0,-1.E0,5.329070518201E-14)); -#12012=VECTOR('',#12011,5.E-2); -#12013=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,7.075E0)); -#12014=LINE('',#12013,#12012); -#12015=DIRECTION('',(0.E0,-1.E0,5.329070518201E-14)); -#12016=VECTOR('',#12015,5.E-2); -#12017=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.149999928474E0)); -#12018=LINE('',#12017,#12016); -#12019=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12020=VECTOR('',#12019,5.E-2); -#12021=CARTESIAN_POINT('',(4.E0,1.55E0,6.606249856949E0)); -#12022=LINE('',#12021,#12020); -#12023=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12024=VECTOR('',#12023,5.E-2); -#12025=CARTESIAN_POINT('',(4.E0,1.55E0,6.700000143051E0)); -#12026=LINE('',#12025,#12024); -#12027=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12028=VECTOR('',#12027,5.E-2); -#12029=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.700000143051E0)); -#12030=LINE('',#12029,#12028); -#12031=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12032=VECTOR('',#12031,5.E-2); -#12033=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.606249856949E0)); -#12034=LINE('',#12033,#12032); -#12035=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12036=VECTOR('',#12035,5.E-2); -#12037=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.606249856949E0)); -#12038=LINE('',#12037,#12036); -#12039=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12040=VECTOR('',#12039,5.E-2); -#12041=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.700000143051E0)); -#12042=LINE('',#12041,#12040); -#12043=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12044=VECTOR('',#12043,5.E-2); -#12045=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.700000143051E0)); -#12046=LINE('',#12045,#12044); -#12047=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12048=VECTOR('',#12047,5.E-2); -#12049=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.606249856949E0)); -#12050=LINE('',#12049,#12048); -#12051=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12052=VECTOR('',#12051,5.E-2); -#12053=CARTESIAN_POINT('',(4.E0,1.55E0,5.818749856949E0)); -#12054=LINE('',#12053,#12052); -#12055=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#12056=VECTOR('',#12055,5.E-2); -#12057=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.081250143051E0)); -#12058=LINE('',#12057,#12056); -#12059=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12060=VECTOR('',#12059,5.E-2); -#12061=CARTESIAN_POINT('',(4.E0,1.55E0,6.34375E0)); -#12062=LINE('',#12061,#12060); -#12063=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12064=VECTOR('',#12063,5.E-2); -#12065=CARTESIAN_POINT('',(4.E0,1.55E0,6.45625E0)); -#12066=LINE('',#12065,#12064); -#12067=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12068=VECTOR('',#12067,5.E-2); -#12069=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.137500143051E0)); -#12070=LINE('',#12069,#12068); -#12071=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12072=VECTOR('',#12071,5.E-2); -#12073=CARTESIAN_POINT('',(3.E0,1.55E0,6.45625E0)); -#12074=LINE('',#12073,#12072); -#12075=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#12076=VECTOR('',#12075,5.E-2); -#12077=CARTESIAN_POINT('',(3.E0,1.55E0,6.34375E0)); -#12078=LINE('',#12077,#12076); -#12079=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12080=VECTOR('',#12079,5.E-2); -#12081=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.081250143051E0)); -#12082=LINE('',#12081,#12080); -#12083=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12084=VECTOR('',#12083,5.E-2); -#12085=CARTESIAN_POINT('',(3.E0,1.55E0,5.818749856949E0)); -#12086=LINE('',#12085,#12084); -#12087=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#12088=VECTOR('',#12087,5.E-2); -#12089=CARTESIAN_POINT('',(3.E0,1.55E0,5.706249856949E0)); -#12090=LINE('',#12089,#12088); -#12091=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12092=VECTOR('',#12091,5.E-2); -#12093=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.025000143051E0)); -#12094=LINE('',#12093,#12092); -#12095=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12096=VECTOR('',#12095,5.E-2); -#12097=CARTESIAN_POINT('',(4.E0,1.55E0,5.706249856949E0)); -#12098=LINE('',#12097,#12096); -#12099=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#12100=VECTOR('',#12099,5.E-2); -#12101=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.406250143051E0)); -#12102=LINE('',#12101,#12100); -#12103=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12104=VECTOR('',#12103,5.E-2); -#12105=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,5.44375E0)); -#12106=LINE('',#12105,#12104); -#12107=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12108=VECTOR('',#12107,5.E-2); -#12109=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,5.5E0)); -#12110=LINE('',#12109,#12108); -#12111=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12112=VECTOR('',#12111,5.E-2); -#12113=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,5.537499856949E0)); -#12114=LINE('',#12113,#12112); -#12115=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12116=VECTOR('',#12115,5.E-2); -#12117=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.537499856949E0)); -#12118=LINE('',#12117,#12116); -#12119=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12120=VECTOR('',#12119,5.E-2); -#12121=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.5E0)); -#12122=LINE('',#12121,#12120); -#12123=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12124=VECTOR('',#12123,5.E-2); -#12125=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,5.44375E0)); -#12126=LINE('',#12125,#12124); -#12127=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12128=VECTOR('',#12127,5.E-2); -#12129=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.350000143051E0)); -#12130=LINE('',#12129,#12128); -#12131=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12132=VECTOR('',#12131,5.E-2); -#12133=CARTESIAN_POINT('',(3.E0,1.55E0,5.256249856949E0)); -#12134=LINE('',#12133,#12132); -#12135=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12136=VECTOR('',#12135,5.E-2); -#12137=CARTESIAN_POINT('',(3.E0,1.55E0,5.181250143051E0)); -#12138=LINE('',#12137,#12136); -#12139=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12140=VECTOR('',#12139,5.E-2); -#12141=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.087499856949E0)); -#12142=LINE('',#12141,#12140); -#12143=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12144=VECTOR('',#12143,5.E-2); -#12145=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,4.99375E0)); -#12146=LINE('',#12145,#12144); -#12147=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12148=VECTOR('',#12147,5.E-2); -#12149=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,4.9375E0)); -#12150=LINE('',#12149,#12148); -#12151=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12152=VECTOR('',#12151,5.E-2); -#12153=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.900000143051E0)); -#12154=LINE('',#12153,#12152); -#12155=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12156=VECTOR('',#12155,5.E-2); -#12157=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,4.900000143051E0)); -#12158=LINE('',#12157,#12156); -#12159=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12160=VECTOR('',#12159,5.E-2); -#12161=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,4.9375E0)); -#12162=LINE('',#12161,#12160); -#12163=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12164=VECTOR('',#12163,5.E-2); -#12165=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,4.99375E0)); -#12166=LINE('',#12165,#12164); -#12167=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12168=VECTOR('',#12167,5.E-2); -#12169=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.031249856949E0)); -#12170=LINE('',#12169,#12168); -#12171=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12172=VECTOR('',#12171,5.E-2); -#12173=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,4.99375E0)); -#12174=LINE('',#12173,#12172); -#12175=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12176=VECTOR('',#12175,5.E-2); -#12177=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,4.918749856949E0)); -#12178=LINE('',#12177,#12176); -#12179=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12180=VECTOR('',#12179,5.E-2); -#12181=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.88125E0)); -#12182=LINE('',#12181,#12180); -#12183=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12184=VECTOR('',#12183,5.E-2); -#12185=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.88125E0)); -#12186=LINE('',#12185,#12184); -#12187=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12188=VECTOR('',#12187,5.E-2); -#12189=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,4.918749856949E0)); -#12190=LINE('',#12189,#12188); -#12191=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12192=VECTOR('',#12191,5.E-2); -#12193=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,4.974999856949E0)); -#12194=LINE('',#12193,#12192); -#12195=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12196=VECTOR('',#12195,5.E-2); -#12197=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.068750143051E0)); -#12198=LINE('',#12197,#12196); -#12199=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12200=VECTOR('',#12199,5.E-2); -#12201=CARTESIAN_POINT('',(4.E0,1.55E0,5.1625E0)); -#12202=LINE('',#12201,#12200); -#12203=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12204=VECTOR('',#12203,5.E-2); -#12205=CARTESIAN_POINT('',(4.E0,1.55E0,5.275E0)); -#12206=LINE('',#12205,#12204); -#12207=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12208=VECTOR('',#12207,5.E-2); -#12209=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.368749856949E0)); -#12210=LINE('',#12209,#12208); -#12211=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12212=VECTOR('',#12211,5.E-2); -#12213=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,5.462500143051E0)); -#12214=LINE('',#12213,#12212); -#12215=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12216=VECTOR('',#12215,5.E-2); -#12217=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,5.518750143051E0)); -#12218=LINE('',#12217,#12216); -#12219=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12220=VECTOR('',#12219,5.E-2); -#12221=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.55625E0)); -#12222=LINE('',#12221,#12220); -#12223=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12224=VECTOR('',#12223,5.E-2); -#12225=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.55625E0)); -#12226=LINE('',#12225,#12224); -#12227=DIRECTION('',(2.664535259100E-14,-1.E0,3.552713678800E-14)); -#12228=VECTOR('',#12227,5.E-2); -#12229=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,5.518750143051E0)); -#12230=LINE('',#12229,#12228); -#12231=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12232=VECTOR('',#12231,5.E-2); -#12233=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,5.44375E0)); -#12234=LINE('',#12233,#12232); -#12235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12236=VECTOR('',#12235,5.E-2); -#12237=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.256249856949E0)); -#12238=LINE('',#12237,#12236); -#12239=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12240=VECTOR('',#12239,5.E-2); -#12241=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.181250143051E0)); -#12242=LINE('',#12241,#12240); -#12243=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12244=VECTOR('',#12243,5.E-2); -#12245=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.10625E0)); -#12246=LINE('',#12245,#12244); -#12247=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12248=VECTOR('',#12247,5.E-2); -#12249=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.031249856949E0)); -#12250=LINE('',#12249,#12248); -#12251=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12252=VECTOR('',#12251,5.E-2); -#12253=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.974999856949E0)); -#12254=LINE('',#12253,#12252); -#12255=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#12256=VECTOR('',#12255,5.E-2); -#12257=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.974999856949E0)); -#12258=LINE('',#12257,#12256); -#12259=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12260=VECTOR('',#12259,5.E-2); -#12261=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.031249856949E0)); -#12262=LINE('',#12261,#12260); -#12263=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12264=VECTOR('',#12263,5.E-2); -#12265=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.10625E0)); -#12266=LINE('',#12265,#12264); -#12267=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12268=VECTOR('',#12267,5.E-2); -#12269=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.181250143051E0)); -#12270=LINE('',#12269,#12268); -#12271=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12272=VECTOR('',#12271,5.E-2); -#12273=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.256249856949E0)); -#12274=LINE('',#12273,#12272); -#12275=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12276=VECTOR('',#12275,5.E-2); -#12277=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.33125E0)); -#12278=LINE('',#12277,#12276); -#12279=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12280=VECTOR('',#12279,5.E-2); -#12281=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.406250143051E0)); -#12282=LINE('',#12281,#12280); -#12283=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12284=VECTOR('',#12283,5.E-2); -#12285=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.462500143051E0)); -#12286=LINE('',#12285,#12284); -#12287=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12288=VECTOR('',#12287,5.E-2); -#12289=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.462500143051E0)); -#12290=LINE('',#12289,#12288); -#12291=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12292=VECTOR('',#12291,5.E-2); -#12293=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.406250143051E0)); -#12294=LINE('',#12293,#12292); -#12295=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12296=VECTOR('',#12295,5.E-2); -#12297=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.33125E0)); -#12298=LINE('',#12297,#12296); -#12299=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12300=VECTOR('',#12299,5.E-2); -#12301=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.181250143051E0)); -#12302=LINE('',#12301,#12300); -#12303=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12304=VECTOR('',#12303,5.E-2); -#12305=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.256249856949E0)); -#12306=LINE('',#12305,#12304); -#12307=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#12308=VECTOR('',#12307,5.E-2); -#12309=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.33125E0)); -#12310=LINE('',#12309,#12308); -#12311=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12312=VECTOR('',#12311,5.E-2); -#12313=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.406250143051E0)); -#12314=LINE('',#12313,#12312); -#12315=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12316=VECTOR('',#12315,5.E-2); -#12317=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.44375E0)); -#12318=LINE('',#12317,#12316); -#12319=DIRECTION('',(-1.776356839400E-14,-1.E0,1.776356839400E-14)); -#12320=VECTOR('',#12319,5.E-2); -#12321=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,5.44375E0)); -#12322=LINE('',#12321,#12320); -#12323=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12324=VECTOR('',#12323,5.E-2); -#12325=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.406250143051E0)); -#12326=LINE('',#12325,#12324); -#12327=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#12328=VECTOR('',#12327,5.E-2); -#12329=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.33125E0)); -#12330=LINE('',#12329,#12328); -#12331=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12332=VECTOR('',#12331,5.E-2); -#12333=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.256249856949E0)); -#12334=LINE('',#12333,#12332); -#12335=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12336=VECTOR('',#12335,5.E-2); -#12337=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.181250143051E0)); -#12338=LINE('',#12337,#12336); -#12339=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12340=VECTOR('',#12339,5.E-2); -#12341=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.10625E0)); -#12342=LINE('',#12341,#12340); -#12343=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12344=VECTOR('',#12343,5.E-2); -#12345=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.031249856949E0)); -#12346=LINE('',#12345,#12344); -#12347=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12348=VECTOR('',#12347,5.E-2); -#12349=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,4.99375E0)); -#12350=LINE('',#12349,#12348); -#12351=DIRECTION('',(2.664535259100E-14,-1.E0,-1.776356839400E-14)); -#12352=VECTOR('',#12351,5.E-2); -#12353=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.99375E0)); -#12354=LINE('',#12353,#12352); -#12355=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12356=VECTOR('',#12355,5.E-2); -#12357=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.031249856949E0)); -#12358=LINE('',#12357,#12356); -#12359=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12360=VECTOR('',#12359,5.E-2); -#12361=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.10625E0)); -#12362=LINE('',#12361,#12360); -#12363=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12364=VECTOR('',#12363,5.E-2); -#12365=CARTESIAN_POINT('',(4.E0,1.55E0,4.43125E0)); -#12366=LINE('',#12365,#12364); -#12367=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12368=VECTOR('',#12367,5.E-2); -#12369=CARTESIAN_POINT('',(4.E0,1.55E0,4.581249856949E0)); -#12370=LINE('',#12369,#12368); -#12371=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12372=VECTOR('',#12371,5.E-2); -#12373=CARTESIAN_POINT('',(3.E0,1.55E0,4.731250143051E0)); -#12374=LINE('',#12373,#12372); -#12375=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#12376=VECTOR('',#12375,5.E-2); -#12377=CARTESIAN_POINT('',(3.E0,1.55E0,4.618750143051E0)); -#12378=LINE('',#12377,#12376); -#12379=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12380=VECTOR('',#12379,5.E-2); -#12381=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.506250143051E0)); -#12382=LINE('',#12381,#12380); -#12383=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12384=VECTOR('',#12383,5.E-2); -#12385=CARTESIAN_POINT('',(3.E0,1.55E0,4.356249856949E0)); -#12386=LINE('',#12385,#12384); -#12387=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12388=VECTOR('',#12387,5.E-2); -#12389=CARTESIAN_POINT('',(3.E0,1.55E0,4.20625E0)); -#12390=LINE('',#12389,#12388); -#12391=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12392=VECTOR('',#12391,5.E-2); -#12393=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.056250143051E0)); -#12394=LINE('',#12393,#12392); -#12395=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12396=VECTOR('',#12395,5.E-2); -#12397=CARTESIAN_POINT('',(3.E0,1.55E0,3.943750143051E0)); -#12398=LINE('',#12397,#12396); -#12399=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12400=VECTOR('',#12399,5.E-2); -#12401=CARTESIAN_POINT('',(3.E0,1.55E0,3.831250143051E0)); -#12402=LINE('',#12401,#12400); -#12403=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12404=VECTOR('',#12403,5.E-2); -#12405=CARTESIAN_POINT('',(4.E0,1.55E0,3.98125E0)); -#12406=LINE('',#12405,#12404); -#12407=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12408=VECTOR('',#12407,5.E-2); -#12409=CARTESIAN_POINT('',(4.E0,1.55E0,4.131249856949E0)); -#12410=LINE('',#12409,#12408); -#12411=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12412=VECTOR('',#12411,5.E-2); -#12413=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,4.281250143051E0)); -#12414=LINE('',#12413,#12412); -#12415=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#12416=VECTOR('',#12415,5.E-2); -#12417=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,3.099999713898E0)); -#12418=LINE('',#12417,#12416); -#12419=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12420=VECTOR('',#12419,5.E-2); -#12421=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,3.062500286102E0)); -#12422=LINE('',#12421,#12420); -#12423=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12424=VECTOR('',#12423,5.E-2); -#12425=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,3.006250286102E0)); -#12426=LINE('',#12425,#12424); -#12427=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12428=VECTOR('',#12427,5.E-2); -#12429=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,2.987499713898E0)); -#12430=LINE('',#12429,#12428); -#12431=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12432=VECTOR('',#12431,5.E-2); -#12433=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,2.987499713898E0)); -#12434=LINE('',#12433,#12432); -#12435=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12436=VECTOR('',#12435,5.E-2); -#12437=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,3.006250286102E0)); -#12438=LINE('',#12437,#12436); -#12439=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#12440=VECTOR('',#12439,5.E-2); -#12441=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,3.062500286102E0)); -#12442=LINE('',#12441,#12440); -#12443=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12444=VECTOR('',#12443,5.E-2); -#12445=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,3.1375E0)); -#12446=LINE('',#12445,#12444); -#12447=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12448=VECTOR('',#12447,5.E-2); -#12449=CARTESIAN_POINT('',(4.E0,1.55E0,3.231250286102E0)); -#12450=LINE('',#12449,#12448); -#12451=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12452=VECTOR('',#12451,5.E-2); -#12453=CARTESIAN_POINT('',(4.E0,1.55E0,3.681249856949E0)); -#12454=LINE('',#12453,#12452); -#12455=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12456=VECTOR('',#12455,5.E-2); -#12457=CARTESIAN_POINT('',(3.E0,1.55E0,3.681249856949E0)); -#12458=LINE('',#12457,#12456); -#12459=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12460=VECTOR('',#12459,5.E-2); -#12461=CARTESIAN_POINT('',(3.E0,1.55E0,3.231250286102E0)); -#12462=LINE('',#12461,#12460); -#12463=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12464=VECTOR('',#12463,5.E-2); -#12465=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,3.1375E0)); -#12466=LINE('',#12465,#12464); -#12467=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12468=VECTOR('',#12467,5.E-2); -#12469=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,3.062500286102E0)); -#12470=LINE('',#12469,#12468); -#12471=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12472=VECTOR('',#12471,5.E-2); -#12473=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,3.006250286102E0)); -#12474=LINE('',#12473,#12472); -#12475=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12476=VECTOR('',#12475,5.E-2); -#12477=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.987499713898E0)); -#12478=LINE('',#12477,#12476); -#12479=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12480=VECTOR('',#12479,5.E-2); -#12481=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,2.987499713898E0)); -#12482=LINE('',#12481,#12480); -#12483=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12484=VECTOR('',#12483,5.E-2); -#12485=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,3.006250286102E0)); -#12486=LINE('',#12485,#12484); -#12487=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#12488=VECTOR('',#12487,5.E-2); -#12489=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,3.062500286102E0)); -#12490=LINE('',#12489,#12488); -#12491=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12492=VECTOR('',#12491,5.E-2); -#12493=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.568749856949E0)); -#12494=LINE('',#12493,#12492); -#12495=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12496=VECTOR('',#12495,5.E-2); -#12497=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.568749856949E0)); -#12498=LINE('',#12497,#12496); -#12499=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12500=VECTOR('',#12499,5.E-2); -#12501=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.212499713898E0)); -#12502=LINE('',#12501,#12500); -#12503=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12504=VECTOR('',#12503,5.E-2); -#12505=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,3.156249713898E0)); -#12506=LINE('',#12505,#12504); -#12507=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12508=VECTOR('',#12507,5.E-2); -#12509=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,3.118750286102E0)); -#12510=LINE('',#12509,#12508); -#12511=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12512=VECTOR('',#12511,5.E-2); -#12513=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,3.099999713898E0)); -#12514=LINE('',#12513,#12512); -#12515=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12516=VECTOR('',#12515,5.E-2); -#12517=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,3.099999713898E0)); -#12518=LINE('',#12517,#12516); -#12519=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12520=VECTOR('',#12519,5.E-2); -#12521=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,3.118750286102E0)); -#12522=LINE('',#12521,#12520); -#12523=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12524=VECTOR('',#12523,5.E-2); -#12525=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,3.156249713898E0)); -#12526=LINE('',#12525,#12524); -#12527=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12528=VECTOR('',#12527,5.E-2); -#12529=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.212499713898E0)); -#12530=LINE('',#12529,#12528); -#12531=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12532=VECTOR('',#12531,5.E-2); -#12533=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,3.099999713898E0)); -#12534=LINE('',#12533,#12532); -#12535=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12536=VECTOR('',#12535,5.E-2); -#12537=CARTESIAN_POINT('',(3.617021262646E0,1.55E0,3.118750286102E0)); -#12538=LINE('',#12537,#12536); -#12539=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12540=VECTOR('',#12539,5.E-2); -#12541=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,3.156249713898E0)); -#12542=LINE('',#12541,#12540); -#12543=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12544=VECTOR('',#12543,5.E-2); -#12545=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.212499713898E0)); -#12546=LINE('',#12545,#12544); -#12547=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12548=VECTOR('',#12547,5.E-2); -#12549=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.568749856949E0)); -#12550=LINE('',#12549,#12548); -#12551=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12552=VECTOR('',#12551,5.E-2); -#12553=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.568749856949E0)); -#12554=LINE('',#12553,#12552); -#12555=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12556=VECTOR('',#12555,5.E-2); -#12557=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.212499713898E0)); -#12558=LINE('',#12557,#12556); -#12559=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12560=VECTOR('',#12559,5.E-2); -#12561=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,3.156249713898E0)); -#12562=LINE('',#12561,#12560); -#12563=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12564=VECTOR('',#12563,5.E-2); -#12565=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,3.118750286102E0)); -#12566=LINE('',#12565,#12564); -#12567=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12568=VECTOR('',#12567,5.E-2); -#12569=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,3.099999713898E0)); -#12570=LINE('',#12569,#12568); -#12571=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12572=VECTOR('',#12571,5.E-2); -#12573=CARTESIAN_POINT('',(3.E0,1.55E0,2.125E0)); -#12574=LINE('',#12573,#12572); -#12575=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12576=VECTOR('',#12575,5.E-2); -#12577=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.125E0)); -#12578=LINE('',#12577,#12576); -#12579=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12580=VECTOR('',#12579,5.E-2); -#12581=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.424999713898E0)); -#12582=LINE('',#12581,#12580); -#12583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12584=VECTOR('',#12583,5.E-2); -#12585=CARTESIAN_POINT('',(4.E0,1.55E0,2.424999713898E0)); -#12586=LINE('',#12585,#12584); -#12587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12588=VECTOR('',#12587,5.E-2); -#12589=CARTESIAN_POINT('',(4.E0,1.55E0,2.537499713898E0)); -#12590=LINE('',#12589,#12588); -#12591=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12592=VECTOR('',#12591,5.E-2); -#12593=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.537499713898E0)); -#12594=LINE('',#12593,#12592); -#12595=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12596=VECTOR('',#12595,5.E-2); -#12597=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.837500286102E0)); -#12598=LINE('',#12597,#12596); -#12599=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12600=VECTOR('',#12599,5.E-2); -#12601=CARTESIAN_POINT('',(3.E0,1.55E0,2.837500286102E0)); -#12602=LINE('',#12601,#12600); -#12603=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12604=VECTOR('',#12603,5.E-2); -#12605=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.825000286102E0)); -#12606=LINE('',#12605,#12604); -#12607=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12608=VECTOR('',#12607,5.E-2); -#12609=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.862499713898E0)); -#12610=LINE('',#12609,#12608); -#12611=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12612=VECTOR('',#12611,5.E-2); -#12613=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.918749713898E0)); -#12614=LINE('',#12613,#12612); -#12615=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12616=VECTOR('',#12615,5.E-2); -#12617=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.95625E0)); -#12618=LINE('',#12617,#12616); -#12619=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12620=VECTOR('',#12619,5.E-2); -#12621=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.95625E0)); -#12622=LINE('',#12621,#12620); -#12623=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12624=VECTOR('',#12623,5.E-2); -#12625=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.918749713898E0)); -#12626=LINE('',#12625,#12624); -#12627=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12628=VECTOR('',#12627,5.E-2); -#12629=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.862499713898E0)); -#12630=LINE('',#12629,#12628); -#12631=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12632=VECTOR('',#12631,5.E-2); -#12633=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.768750286102E0)); -#12634=LINE('',#12633,#12632); -#12635=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12636=VECTOR('',#12635,5.E-2); -#12637=CARTESIAN_POINT('',(3.E0,1.55E0,1.675E0)); -#12638=LINE('',#12637,#12636); -#12639=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12640=VECTOR('',#12639,5.E-2); -#12641=CARTESIAN_POINT('',(3.E0,1.55E0,1.600000286102E0)); -#12642=LINE('',#12641,#12640); -#12643=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12644=VECTOR('',#12643,5.E-2); -#12645=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.50625E0)); -#12646=LINE('',#12645,#12644); -#12647=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12648=VECTOR('',#12647,5.E-2); -#12649=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.412499713898E0)); -#12650=LINE('',#12649,#12648); -#12651=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12652=VECTOR('',#12651,5.E-2); -#12653=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.356249713898E0)); -#12654=LINE('',#12653,#12652); -#12655=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12656=VECTOR('',#12655,5.E-2); -#12657=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.318750286102E0)); -#12658=LINE('',#12657,#12656); -#12659=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12660=VECTOR('',#12659,5.E-2); -#12661=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.318750286102E0)); -#12662=LINE('',#12661,#12660); -#12663=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12664=VECTOR('',#12663,5.E-2); -#12665=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.356249713898E0)); -#12666=LINE('',#12665,#12664); -#12667=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12668=VECTOR('',#12667,5.E-2); -#12669=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.412499713898E0)); -#12670=LINE('',#12669,#12668); -#12671=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12672=VECTOR('',#12671,5.E-2); -#12673=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.45E0)); -#12674=LINE('',#12673,#12672); -#12675=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12676=VECTOR('',#12675,5.E-2); -#12677=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.412499713898E0)); -#12678=LINE('',#12677,#12676); -#12679=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12680=VECTOR('',#12679,5.E-2); -#12681=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.3375E0)); -#12682=LINE('',#12681,#12680); -#12683=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12684=VECTOR('',#12683,5.E-2); -#12685=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.299999713898E0)); -#12686=LINE('',#12685,#12684); -#12687=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12688=VECTOR('',#12687,5.E-2); -#12689=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.299999713898E0)); -#12690=LINE('',#12689,#12688); -#12691=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12692=VECTOR('',#12691,5.E-2); -#12693=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.3375E0)); -#12694=LINE('',#12693,#12692); -#12695=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12696=VECTOR('',#12695,5.E-2); -#12697=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.39375E0)); -#12698=LINE('',#12697,#12696); -#12699=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12700=VECTOR('',#12699,5.E-2); -#12701=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.487500286102E0)); -#12702=LINE('',#12701,#12700); -#12703=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12704=VECTOR('',#12703,5.E-2); -#12705=CARTESIAN_POINT('',(4.E0,1.55E0,1.581249713898E0)); -#12706=LINE('',#12705,#12704); -#12707=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12708=VECTOR('',#12707,5.E-2); -#12709=CARTESIAN_POINT('',(4.E0,1.55E0,1.693749713898E0)); -#12710=LINE('',#12709,#12708); -#12711=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12712=VECTOR('',#12711,5.E-2); -#12713=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.7875E0)); -#12714=LINE('',#12713,#12712); -#12715=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12716=VECTOR('',#12715,5.E-2); -#12717=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.881250286102E0)); -#12718=LINE('',#12717,#12716); -#12719=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12720=VECTOR('',#12719,5.E-2); -#12721=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.937500286102E0)); -#12722=LINE('',#12721,#12720); -#12723=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12724=VECTOR('',#12723,5.E-2); -#12725=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.974999713898E0)); -#12726=LINE('',#12725,#12724); -#12727=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12728=VECTOR('',#12727,5.E-2); -#12729=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.974999713898E0)); -#12730=LINE('',#12729,#12728); -#12731=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12732=VECTOR('',#12731,5.E-2); -#12733=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.937500286102E0)); -#12734=LINE('',#12733,#12732); -#12735=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12736=VECTOR('',#12735,5.E-2); -#12737=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.862499713898E0)); -#12738=LINE('',#12737,#12736); -#12739=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12740=VECTOR('',#12739,5.E-2); -#12741=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.675E0)); -#12742=LINE('',#12741,#12740); -#12743=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12744=VECTOR('',#12743,5.E-2); -#12745=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.600000286102E0)); -#12746=LINE('',#12745,#12744); -#12747=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12748=VECTOR('',#12747,5.E-2); -#12749=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.524999713898E0)); -#12750=LINE('',#12749,#12748); -#12751=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12752=VECTOR('',#12751,5.E-2); -#12753=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.45E0)); -#12754=LINE('',#12753,#12752); -#12755=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12756=VECTOR('',#12755,5.E-2); -#12757=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.39375E0)); -#12758=LINE('',#12757,#12756); -#12759=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#12760=VECTOR('',#12759,5.E-2); -#12761=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.39375E0)); -#12762=LINE('',#12761,#12760); -#12763=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12764=VECTOR('',#12763,5.E-2); -#12765=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.45E0)); -#12766=LINE('',#12765,#12764); -#12767=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12768=VECTOR('',#12767,5.E-2); -#12769=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.524999713898E0)); -#12770=LINE('',#12769,#12768); -#12771=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12772=VECTOR('',#12771,5.E-2); -#12773=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.600000286102E0)); -#12774=LINE('',#12773,#12772); -#12775=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12776=VECTOR('',#12775,5.E-2); -#12777=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.675E0)); -#12778=LINE('',#12777,#12776); -#12779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12780=VECTOR('',#12779,5.E-2); -#12781=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.749999713898E0)); -#12782=LINE('',#12781,#12780); -#12783=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12784=VECTOR('',#12783,5.E-2); -#12785=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.825000286102E0)); -#12786=LINE('',#12785,#12784); -#12787=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12788=VECTOR('',#12787,5.E-2); -#12789=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.881250286102E0)); -#12790=LINE('',#12789,#12788); -#12791=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12792=VECTOR('',#12791,5.E-2); -#12793=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.881250286102E0)); -#12794=LINE('',#12793,#12792); -#12795=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12796=VECTOR('',#12795,5.E-2); -#12797=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.825000286102E0)); -#12798=LINE('',#12797,#12796); -#12799=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12800=VECTOR('',#12799,5.E-2); -#12801=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.749999713898E0)); -#12802=LINE('',#12801,#12800); -#12803=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12804=VECTOR('',#12803,5.E-2); -#12805=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.600000286102E0)); -#12806=LINE('',#12805,#12804); -#12807=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12808=VECTOR('',#12807,5.E-2); -#12809=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.675E0)); -#12810=LINE('',#12809,#12808); -#12811=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12812=VECTOR('',#12811,5.E-2); -#12813=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.749999713898E0)); -#12814=LINE('',#12813,#12812); -#12815=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12816=VECTOR('',#12815,5.E-2); -#12817=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.825000286102E0)); -#12818=LINE('',#12817,#12816); -#12819=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12820=VECTOR('',#12819,5.E-2); -#12821=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.862499713898E0)); -#12822=LINE('',#12821,#12820); -#12823=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12824=VECTOR('',#12823,5.E-2); -#12825=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.862499713898E0)); -#12826=LINE('',#12825,#12824); -#12827=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12828=VECTOR('',#12827,5.E-2); -#12829=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.825000286102E0)); -#12830=LINE('',#12829,#12828); -#12831=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12832=VECTOR('',#12831,5.E-2); -#12833=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.749999713898E0)); -#12834=LINE('',#12833,#12832); -#12835=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12836=VECTOR('',#12835,5.E-2); -#12837=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.675E0)); -#12838=LINE('',#12837,#12836); -#12839=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12840=VECTOR('',#12839,5.E-2); -#12841=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.600000286102E0)); -#12842=LINE('',#12841,#12840); -#12843=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12844=VECTOR('',#12843,5.E-2); -#12845=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.524999713898E0)); -#12846=LINE('',#12845,#12844); -#12847=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12848=VECTOR('',#12847,5.E-2); -#12849=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.45E0)); -#12850=LINE('',#12849,#12848); -#12851=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12852=VECTOR('',#12851,5.E-2); -#12853=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.412499713898E0)); -#12854=LINE('',#12853,#12852); -#12855=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12856=VECTOR('',#12855,5.E-2); -#12857=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.412499713898E0)); -#12858=LINE('',#12857,#12856); -#12859=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12860=VECTOR('',#12859,5.E-2); -#12861=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.45E0)); -#12862=LINE('',#12861,#12860); -#12863=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12864=VECTOR('',#12863,5.E-2); -#12865=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.524999713898E0)); -#12866=LINE('',#12865,#12864); -#12867=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12868=VECTOR('',#12867,5.E-2); -#12869=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.312502861023E-1)); -#12870=LINE('',#12869,#12868); -#12871=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12872=VECTOR('',#12871,5.E-2); -#12873=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,5.875002861023E-1)); -#12874=LINE('',#12873,#12872); -#12875=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12876=VECTOR('',#12875,5.E-2); -#12877=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,6.625E-1)); -#12878=LINE('',#12877,#12876); -#12879=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12880=VECTOR('',#12879,5.E-2); -#12881=CARTESIAN_POINT('',(4.E0,1.55E0,7.374997138977E-1)); -#12882=LINE('',#12881,#12880); -#12883=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12884=VECTOR('',#12883,5.E-2); -#12885=CARTESIAN_POINT('',(4.E0,1.55E0,8.875E-1)); -#12886=LINE('',#12885,#12884); -#12887=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12888=VECTOR('',#12887,5.E-2); -#12889=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.624997138977E-1)); -#12890=LINE('',#12889,#12888); -#12891=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12892=VECTOR('',#12891,5.E-2); -#12893=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,1.037500286102E0)); -#12894=LINE('',#12893,#12892); -#12895=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12896=VECTOR('',#12895,5.E-2); -#12897=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.093750286102E0)); -#12898=LINE('',#12897,#12896); -#12899=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12900=VECTOR('',#12899,5.E-2); -#12901=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.131249713898E0)); -#12902=LINE('',#12901,#12900); -#12903=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12904=VECTOR('',#12903,5.E-2); -#12905=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.150000286102E0)); -#12906=LINE('',#12905,#12904); -#12907=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12908=VECTOR('',#12907,5.E-2); -#12909=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.05625E0)); -#12910=LINE('',#12909,#12908); -#12911=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12912=VECTOR('',#12911,5.E-2); -#12913=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,1.037500286102E0)); -#12914=LINE('',#12913,#12912); -#12915=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12916=VECTOR('',#12915,5.E-2); -#12917=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.E0)); -#12918=LINE('',#12917,#12916); -#12919=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12920=VECTOR('',#12919,5.E-2); -#12921=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.624997138977E-1)); -#12922=LINE('',#12921,#12920); -#12923=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12924=VECTOR('',#12923,5.E-2); -#12925=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,8.687502861023E-1)); -#12926=LINE('',#12925,#12924); -#12927=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12928=VECTOR('',#12927,5.E-2); -#12929=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,7.562502861023E-1)); -#12930=LINE('',#12929,#12928); -#12931=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12932=VECTOR('',#12931,5.E-2); -#12933=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,6.625E-1)); -#12934=LINE('',#12933,#12932); -#12935=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12936=VECTOR('',#12935,5.E-2); -#12937=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.249997138977E-1)); -#12938=LINE('',#12937,#12936); -#12939=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12940=VECTOR('',#12939,5.E-2); -#12941=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,5.875002861023E-1)); -#12942=LINE('',#12941,#12940); -#12943=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12944=VECTOR('',#12943,5.E-2); -#12945=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,5.687497138977E-1)); -#12946=LINE('',#12945,#12944); -#12947=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12948=VECTOR('',#12947,5.E-2); -#12949=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.687497138977E-1)); -#12950=LINE('',#12949,#12948); -#12951=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12952=VECTOR('',#12951,5.E-2); -#12953=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.0625E-1)); -#12954=LINE('',#12953,#12952); -#12955=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12956=VECTOR('',#12955,5.E-2); -#12957=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,6.625E-1)); -#12958=LINE('',#12957,#12956); -#12959=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12960=VECTOR('',#12959,5.E-2); -#12961=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,7.75E-1)); -#12962=LINE('',#12961,#12960); -#12963=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12964=VECTOR('',#12963,5.E-2); -#12965=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,8.499997138977E-1)); -#12966=LINE('',#12965,#12964); -#12967=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12968=VECTOR('',#12967,5.E-2); -#12969=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,8.499997138977E-1)); -#12970=LINE('',#12969,#12968); -#12971=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12972=VECTOR('',#12971,5.E-2); -#12973=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,7.75E-1)); -#12974=LINE('',#12973,#12972); -#12975=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12976=VECTOR('',#12975,5.E-2); -#12977=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.625E-1)); -#12978=LINE('',#12977,#12976); -#12979=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12980=VECTOR('',#12979,5.E-2); -#12981=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,6.249997138977E-1)); -#12982=LINE('',#12981,#12980); -#12983=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12984=VECTOR('',#12983,5.E-2); -#12985=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,5.875002861023E-1)); -#12986=LINE('',#12985,#12984); -#12987=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12988=VECTOR('',#12987,5.E-2); -#12989=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,5.875002861023E-1)); -#12990=LINE('',#12989,#12988); -#12991=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12992=VECTOR('',#12991,5.E-2); -#12993=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,6.249997138977E-1)); -#12994=LINE('',#12993,#12992); -#12995=DIRECTION('',(0.E0,-1.E0,0.E0)); -#12996=VECTOR('',#12995,5.E-2); -#12997=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,6.812497138977E-1)); -#12998=LINE('',#12997,#12996); -#12999=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13000=VECTOR('',#12999,5.E-2); -#13001=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,7.75E-1)); -#13002=LINE('',#13001,#13000); -#13003=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13004=VECTOR('',#13003,5.E-2); -#13005=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,8.499997138977E-1)); -#13006=LINE('',#13005,#13004); -#13007=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13008=VECTOR('',#13007,5.E-2); -#13009=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.4375E-1)); -#13010=LINE('',#13009,#13008); -#13011=DIRECTION('',(0.E0,-1.E0,1.110223024625E-14)); -#13012=VECTOR('',#13011,5.E-2); -#13013=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.E0)); -#13014=LINE('',#13013,#13012); -#13015=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13016=VECTOR('',#13015,5.E-2); -#13017=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.037500286102E0)); -#13018=LINE('',#13017,#13016); -#13019=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13020=VECTOR('',#13019,5.E-2); -#13021=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.131249713898E0)); -#13022=LINE('',#13021,#13020); -#13023=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13024=VECTOR('',#13023,5.E-2); -#13025=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.1125E0)); -#13026=LINE('',#13025,#13024); -#13027=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13028=VECTOR('',#13027,5.E-2); -#13029=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,1.037500286102E0)); -#13030=LINE('',#13029,#13028); -#13031=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13032=VECTOR('',#13031,5.E-2); -#13033=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.624997138977E-1)); -#13034=LINE('',#13033,#13032); -#13035=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13036=VECTOR('',#13035,5.E-2); -#13037=CARTESIAN_POINT('',(3.E0,1.55E0,8.3125E-1)); -#13038=LINE('',#13037,#13036); -#13039=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13040=VECTOR('',#13039,5.E-2); -#13041=CARTESIAN_POINT('',(3.E0,1.55E0,7.937497138977E-1)); -#13042=LINE('',#13041,#13040); -#13043=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13044=VECTOR('',#13043,5.E-2); -#13045=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,6.625E-1)); -#13046=LINE('',#13045,#13044); -#13047=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13048=VECTOR('',#13047,5.E-2); -#13049=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,5.875002861023E-1)); -#13050=LINE('',#13049,#13048); -#13051=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13052=VECTOR('',#13051,5.E-2); -#13053=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.124997138977E-1)); -#13054=LINE('',#13053,#13052); -#13055=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13056=VECTOR('',#13055,5.E-2); -#13057=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,4.9375E-1)); -#13058=LINE('',#13057,#13056); -#13059=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13060=VECTOR('',#13059,5.E-2); -#13061=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,4.9375E-1)); -#13062=LINE('',#13061,#13060); -#13063=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13064=VECTOR('',#13063,5.E-2); -#13065=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.124997138977E-1)); -#13066=LINE('',#13065,#13064); -#13067=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13068=VECTOR('',#13067,5.E-2); -#13069=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.5E-1)); -#13070=LINE('',#13069,#13068); -#13071=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13072=VECTOR('',#13071,5.E-2); -#13073=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.249997138977E-1)); -#13074=LINE('',#13073,#13072); -#13075=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13076=VECTOR('',#13075,5.E-2); -#13077=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.312502861023E-1)); -#13078=LINE('',#13077,#13076); -#13079=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13080=VECTOR('',#13079,5.E-2); -#13081=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,4.9375E-1)); -#13082=LINE('',#13081,#13080); -#13083=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13084=VECTOR('',#13083,5.E-2); -#13085=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.750002861023E-1)); -#13086=LINE('',#13085,#13084); -#13087=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13088=VECTOR('',#13087,5.E-2); -#13089=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.750002861023E-1)); -#13090=LINE('',#13089,#13088); -#13091=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13092=VECTOR('',#13091,5.E-2); -#13093=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,4.9375E-1)); -#13094=LINE('',#13093,#13092); -#13095=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13096=VECTOR('',#13095,5.E-2); -#13097=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,3.25E-1)); -#13098=LINE('',#13097,#13096); -#13099=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13100=VECTOR('',#13099,5.E-2); -#13101=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-1.999997138977E-1)); -#13102=LINE('',#13101,#13100); -#13103=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13104=VECTOR('',#13103,5.E-2); -#13105=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-2.375E-1)); -#13106=LINE('',#13105,#13104); -#13107=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13108=VECTOR('',#13107,5.E-2); -#13109=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-2.375E-1)); -#13110=LINE('',#13109,#13108); -#13111=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13112=VECTOR('',#13111,5.E-2); -#13113=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,-1.999997138977E-1)); -#13114=LINE('',#13113,#13112); -#13115=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13116=VECTOR('',#13115,5.E-2); -#13117=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,-1.437497138977E-1)); -#13118=LINE('',#13117,#13116); -#13119=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13120=VECTOR('',#13119,5.E-2); -#13121=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,-5.000028610230E-2)); -#13122=LINE('',#13121,#13120); -#13123=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13124=VECTOR('',#13123,5.E-2); -#13125=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.500028610229E-2)); -#13126=LINE('',#13125,#13124); -#13127=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13128=VECTOR('',#13127,5.E-2); -#13129=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.187497138977E-1)); -#13130=LINE('',#13129,#13128); -#13131=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13132=VECTOR('',#13131,5.E-2); -#13133=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.749997138977E-1)); -#13134=LINE('',#13133,#13132); -#13135=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13136=VECTOR('',#13135,5.E-2); -#13137=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.125E-1)); -#13138=LINE('',#13137,#13136); -#13139=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13140=VECTOR('',#13139,5.E-2); -#13141=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,3.062502861023E-1)); -#13142=LINE('',#13141,#13140); -#13143=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13144=VECTOR('',#13143,5.E-2); -#13145=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,2.874997138977E-1)); -#13146=LINE('',#13145,#13144); -#13147=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13148=VECTOR('',#13147,5.E-2); -#13149=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,2.125E-1)); -#13150=LINE('',#13149,#13148); -#13151=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13152=VECTOR('',#13151,5.E-2); -#13153=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.375002861023E-1)); -#13154=LINE('',#13153,#13152); -#13155=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13156=VECTOR('',#13155,5.E-2); -#13157=CARTESIAN_POINT('',(3.E0,1.55E0,6.249713897704E-3)); -#13158=LINE('',#13157,#13156); -#13159=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13160=VECTOR('',#13159,5.E-2); -#13161=CARTESIAN_POINT('',(3.E0,1.55E0,-6.875E-2)); -#13162=LINE('',#13161,#13160); -#13163=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13164=VECTOR('',#13163,5.E-2); -#13165=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,-1.8125E-1)); -#13166=LINE('',#13165,#13164); -#13167=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13168=VECTOR('',#13167,5.E-2); -#13169=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,-2.562497138977E-1)); -#13170=LINE('',#13169,#13168); -#13171=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13172=VECTOR('',#13171,5.E-2); -#13173=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,-3.312502861023E-1)); -#13174=LINE('',#13173,#13172); -#13175=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13176=VECTOR('',#13175,5.E-2); -#13177=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-3.5E-1)); -#13178=LINE('',#13177,#13176); -#13179=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13180=VECTOR('',#13179,5.E-2); -#13181=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-3.5E-1)); -#13182=LINE('',#13181,#13180); -#13183=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13184=VECTOR('',#13183,5.E-2); -#13185=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-3.312502861023E-1)); -#13186=LINE('',#13185,#13184); -#13187=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13188=VECTOR('',#13187,5.E-2); -#13189=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,-2.9375E-1)); -#13190=LINE('',#13189,#13188); -#13191=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13192=VECTOR('',#13191,5.E-2); -#13193=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.749997138977E-1)); -#13194=LINE('',#13193,#13192); -#13195=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13196=VECTOR('',#13195,5.E-2); -#13197=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,-3.5E-1)); -#13198=LINE('',#13197,#13196); -#13199=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13200=VECTOR('',#13199,5.E-2); -#13201=CARTESIAN_POINT('',(4.E0,1.55E0,-3.5E-1)); -#13202=LINE('',#13201,#13200); -#13203=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13204=VECTOR('',#13203,5.E-2); -#13205=CARTESIAN_POINT('',(4.E0,1.55E0,3.25E-1)); -#13206=LINE('',#13205,#13204); -#13207=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13208=VECTOR('',#13207,5.E-2); -#13209=CARTESIAN_POINT('',(5.75E0,1.55E0,1.03375E1)); -#13210=LINE('',#13209,#13208); -#13211=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13212=VECTOR('',#13211,5.E-2); -#13213=CARTESIAN_POINT('',(5.75E0,1.55E0,1.045E1)); -#13214=LINE('',#13213,#13212); -#13215=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13216=VECTOR('',#13215,5.E-2); -#13217=CARTESIAN_POINT('',(4.75E0,1.55E0,1.045E1)); -#13218=LINE('',#13217,#13216); -#13219=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13220=VECTOR('',#13219,5.E-2); -#13221=CARTESIAN_POINT('',(4.75E0,1.55E0,1.03375E1)); -#13222=LINE('',#13221,#13220); -#13223=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13224=VECTOR('',#13223,5.E-2); -#13225=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.456250035763E0)); -#13226=LINE('',#13225,#13224); -#13227=DIRECTION('',(-1.776356839400E-14,-1.E0,0.E0)); -#13228=VECTOR('',#13227,5.E-2); -#13229=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.474999964237E0)); -#13230=LINE('',#13229,#13228); -#13231=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13232=VECTOR('',#13231,5.E-2); -#13233=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,9.55E0)); -#13234=LINE('',#13233,#13232); -#13235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13236=VECTOR('',#13235,5.E-2); -#13237=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.624999982119E0)); -#13238=LINE('',#13237,#13236); -#13239=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13240=VECTOR('',#13239,5.E-2); -#13241=CARTESIAN_POINT('',(5.75E0,1.55E0,9.71875E0)); -#13242=LINE('',#13241,#13240); -#13243=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13244=VECTOR('',#13243,5.E-2); -#13245=CARTESIAN_POINT('',(5.75E0,1.55E0,9.8875E0)); -#13246=LINE('',#13245,#13244); -#13247=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13248=VECTOR('',#13247,5.E-2); -#13249=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.981250017881E0)); -#13250=LINE('',#13249,#13248); -#13251=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13252=VECTOR('',#13251,5.E-2); -#13253=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.005625E1)); -#13254=LINE('',#13253,#13252); -#13255=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13256=VECTOR('',#13255,5.E-2); -#13257=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.013125000894E1)); -#13258=LINE('',#13257,#13256); -#13259=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13260=VECTOR('',#13259,5.E-2); -#13261=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.016875E1)); -#13262=LINE('',#13261,#13260); -#13263=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13264=VECTOR('',#13263,5.E-2); -#13265=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.018750000894E1)); -#13266=LINE('',#13265,#13264); -#13267=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13268=VECTOR('',#13267,5.E-2); -#13269=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.018750000894E1)); -#13270=LINE('',#13269,#13268); -#13271=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13272=VECTOR('',#13271,5.E-2); -#13273=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.016875E1)); -#13274=LINE('',#13273,#13272); -#13275=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13276=VECTOR('',#13275,5.E-2); -#13277=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.013125000894E1)); -#13278=LINE('',#13277,#13276); -#13279=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13280=VECTOR('',#13279,5.E-2); -#13281=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.005625E1)); -#13282=LINE('',#13281,#13280); -#13283=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13284=VECTOR('',#13283,5.E-2); -#13285=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.981250017881E0)); -#13286=LINE('',#13285,#13284); -#13287=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#13288=VECTOR('',#13287,5.E-2); -#13289=CARTESIAN_POINT('',(4.75E0,1.55E0,9.8875E0)); -#13290=LINE('',#13289,#13288); -#13291=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13292=VECTOR('',#13291,5.E-2); -#13293=CARTESIAN_POINT('',(4.75E0,1.55E0,9.71875E0)); -#13294=LINE('',#13293,#13292); -#13295=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13296=VECTOR('',#13295,5.E-2); -#13297=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.624999982119E0)); -#13298=LINE('',#13297,#13296); -#13299=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13300=VECTOR('',#13299,5.E-2); -#13301=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,9.55E0)); -#13302=LINE('',#13301,#13300); -#13303=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#13304=VECTOR('',#13303,5.E-2); -#13305=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.474999964237E0)); -#13306=LINE('',#13305,#13304); -#13307=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13308=VECTOR('',#13307,5.E-2); -#13309=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.456250035763E0)); -#13310=LINE('',#13309,#13308); -#13311=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13312=VECTOR('',#13311,5.E-2); -#13313=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.568749982119E0)); -#13314=LINE('',#13313,#13312); -#13315=DIRECTION('',(5.329070518201E-14,-1.E0,-7.105427357601E-14)); -#13316=VECTOR('',#13315,5.E-2); -#13317=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,9.587500017881E0)); -#13318=LINE('',#13317,#13316); -#13319=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13320=VECTOR('',#13319,5.E-2); -#13321=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.643750017881E0)); -#13322=LINE('',#13321,#13320); -#13323=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13324=VECTOR('',#13323,5.E-2); -#13325=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.71875E0)); -#13326=LINE('',#13325,#13324); -#13327=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#13328=VECTOR('',#13327,5.E-2); -#13329=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.8875E0)); -#13330=LINE('',#13329,#13328); -#13331=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13332=VECTOR('',#13331,5.E-2); -#13333=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.962499982119E0)); -#13334=LINE('',#13333,#13332); -#13335=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13336=VECTOR('',#13335,5.E-2); -#13337=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.001875000894E1)); -#13338=LINE('',#13337,#13336); -#13339=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13340=VECTOR('',#13339,5.E-2); -#13341=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.005625E1)); -#13342=LINE('',#13341,#13340); -#13343=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13344=VECTOR('',#13343,5.E-2); -#13345=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.007500000894E1)); -#13346=LINE('',#13345,#13344); -#13347=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13348=VECTOR('',#13347,5.E-2); -#13349=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.007500000894E1)); -#13350=LINE('',#13349,#13348); -#13351=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13352=VECTOR('',#13351,5.E-2); -#13353=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.005625E1)); -#13354=LINE('',#13353,#13352); -#13355=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13356=VECTOR('',#13355,5.E-2); -#13357=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.001875000894E1)); -#13358=LINE('',#13357,#13356); -#13359=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13360=VECTOR('',#13359,5.E-2); -#13361=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.962499982119E0)); -#13362=LINE('',#13361,#13360); -#13363=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#13364=VECTOR('',#13363,5.E-2); -#13365=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.8875E0)); -#13366=LINE('',#13365,#13364); -#13367=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13368=VECTOR('',#13367,5.E-2); -#13369=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.71875E0)); -#13370=LINE('',#13369,#13368); -#13371=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13372=VECTOR('',#13371,5.E-2); -#13373=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.643750017881E0)); -#13374=LINE('',#13373,#13372); -#13375=DIRECTION('',(3.552713678800E-14,-1.E0,3.552713678800E-14)); -#13376=VECTOR('',#13375,5.E-2); -#13377=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,9.587500017881E0)); -#13378=LINE('',#13377,#13376); -#13379=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13380=VECTOR('',#13379,5.E-2); -#13381=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.568749982119E0)); -#13382=LINE('',#13381,#13380); -#13383=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13384=VECTOR('',#13383,5.E-2); -#13385=CARTESIAN_POINT('',(5.75E0,1.55E0,9.193749964237E0)); -#13386=LINE('',#13385,#13384); -#13387=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13388=VECTOR('',#13387,5.E-2); -#13389=CARTESIAN_POINT('',(5.75E0,1.55E0,9.306249964237E0)); -#13390=LINE('',#13389,#13388); -#13391=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13392=VECTOR('',#13391,5.E-2); -#13393=CARTESIAN_POINT('',(4.75E0,1.55E0,9.306249964237E0)); -#13394=LINE('',#13393,#13392); -#13395=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13396=VECTOR('',#13395,5.E-2); -#13397=CARTESIAN_POINT('',(4.75E0,1.55E0,9.193749964237E0)); -#13398=LINE('',#13397,#13396); -#13399=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13400=VECTOR('',#13399,5.E-2); -#13401=CARTESIAN_POINT('',(4.75E0,1.55E0,8.59375E0)); -#13402=LINE('',#13401,#13400); -#13403=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13404=VECTOR('',#13403,5.E-2); -#13405=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,8.499999928474E0)); -#13406=LINE('',#13405,#13404); -#13407=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13408=VECTOR('',#13407,5.E-2); -#13409=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,8.425E0)); -#13410=LINE('',#13409,#13408); -#13411=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13412=VECTOR('',#13411,5.E-2); -#13413=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.350000071526E0)); -#13414=LINE('',#13413,#13412); -#13415=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13416=VECTOR('',#13415,5.E-2); -#13417=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,8.3125E0)); -#13418=LINE('',#13417,#13416); -#13419=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13420=VECTOR('',#13419,5.E-2); -#13421=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.293750071526E0)); -#13422=LINE('',#13421,#13420); -#13423=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13424=VECTOR('',#13423,5.E-2); -#13425=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.293750071526E0)); -#13426=LINE('',#13425,#13424); -#13427=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13428=VECTOR('',#13427,5.E-2); -#13429=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,8.3125E0)); -#13430=LINE('',#13429,#13428); -#13431=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13432=VECTOR('',#13431,5.E-2); -#13433=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.350000071526E0)); -#13434=LINE('',#13433,#13432); -#13435=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13436=VECTOR('',#13435,5.E-2); -#13437=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,8.425E0)); -#13438=LINE('',#13437,#13436); -#13439=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13440=VECTOR('',#13439,5.E-2); -#13441=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,8.499999928474E0)); -#13442=LINE('',#13441,#13440); -#13443=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13444=VECTOR('',#13443,5.E-2); -#13445=CARTESIAN_POINT('',(5.75E0,1.55E0,8.59375E0)); -#13446=LINE('',#13445,#13444); -#13447=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13448=VECTOR('',#13447,5.E-2); -#13449=CARTESIAN_POINT('',(5.75E0,1.55E0,9.04375E0)); -#13450=LINE('',#13449,#13448); -#13451=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13452=VECTOR('',#13451,5.E-2); -#13453=CARTESIAN_POINT('',(4.75E0,1.55E0,9.04375E0)); -#13454=LINE('',#13453,#13452); -#13455=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13456=VECTOR('',#13455,5.E-2); -#13457=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.93125E0)); -#13458=LINE('',#13457,#13456); -#13459=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13460=VECTOR('',#13459,5.E-2); -#13461=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.93125E0)); -#13462=LINE('',#13461,#13460); -#13463=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13464=VECTOR('',#13463,5.E-2); -#13465=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.59375E0)); -#13466=LINE('',#13465,#13464); -#13467=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13468=VECTOR('',#13467,5.E-2); -#13469=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.518750071526E0)); -#13470=LINE('',#13469,#13468); -#13471=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13472=VECTOR('',#13471,5.E-2); -#13473=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,8.462500071526E0)); -#13474=LINE('',#13473,#13472); -#13475=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13476=VECTOR('',#13475,5.E-2); -#13477=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,8.425E0)); -#13478=LINE('',#13477,#13476); -#13479=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13480=VECTOR('',#13479,5.E-2); -#13481=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.406250071526E0)); -#13482=LINE('',#13481,#13480); -#13483=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13484=VECTOR('',#13483,5.E-2); -#13485=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.406250071526E0)); -#13486=LINE('',#13485,#13484); -#13487=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13488=VECTOR('',#13487,5.E-2); -#13489=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,8.425E0)); -#13490=LINE('',#13489,#13488); -#13491=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13492=VECTOR('',#13491,5.E-2); -#13493=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,8.462500071526E0)); -#13494=LINE('',#13493,#13492); -#13495=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13496=VECTOR('',#13495,5.E-2); -#13497=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.518750071526E0)); -#13498=LINE('',#13497,#13496); -#13499=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13500=VECTOR('',#13499,5.E-2); -#13501=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.59375E0)); -#13502=LINE('',#13501,#13500); -#13503=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13504=VECTOR('',#13503,5.E-2); -#13505=CARTESIAN_POINT('',(5.75E0,1.55E0,8.049999928474E0)); -#13506=LINE('',#13505,#13504); -#13507=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13508=VECTOR('',#13507,5.E-2); -#13509=CARTESIAN_POINT('',(5.75E0,1.55E0,8.14375E0)); -#13510=LINE('',#13509,#13508); -#13511=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13512=VECTOR('',#13511,5.E-2); -#13513=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.14375E0)); -#13514=LINE('',#13513,#13512); -#13515=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13516=VECTOR('',#13515,5.E-2); -#13517=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.049999928474E0)); -#13518=LINE('',#13517,#13516); -#13519=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13520=VECTOR('',#13519,5.E-2); -#13521=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.049999928474E0)); -#13522=LINE('',#13521,#13520); -#13523=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13524=VECTOR('',#13523,5.E-2); -#13525=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.14375E0)); -#13526=LINE('',#13525,#13524); -#13527=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13528=VECTOR('',#13527,5.E-2); -#13529=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.14375E0)); -#13530=LINE('',#13529,#13528); -#13531=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13532=VECTOR('',#13531,5.E-2); -#13533=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.049999928474E0)); -#13534=LINE('',#13533,#13532); -#13535=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13536=VECTOR('',#13535,5.E-2); -#13537=CARTESIAN_POINT('',(4.75E0,1.55E0,7.450000071526E0)); -#13538=LINE('',#13537,#13536); -#13539=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13540=VECTOR('',#13539,5.E-2); -#13541=CARTESIAN_POINT('',(4.75E0,1.55E0,7.337500071526E0)); -#13542=LINE('',#13541,#13540); -#13543=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13544=VECTOR('',#13543,5.E-2); -#13545=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.337500071526E0)); -#13546=LINE('',#13545,#13544); -#13547=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13548=VECTOR('',#13547,5.E-2); -#13549=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.149999928474E0)); -#13550=LINE('',#13549,#13548); -#13551=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13552=VECTOR('',#13551,5.E-2); -#13553=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.149999928474E0)); -#13554=LINE('',#13553,#13552); -#13555=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13556=VECTOR('',#13555,5.E-2); -#13557=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.337500071526E0)); -#13558=LINE('',#13557,#13556); -#13559=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13560=VECTOR('',#13559,5.E-2); -#13561=CARTESIAN_POINT('',(5.75E0,1.55E0,7.337500071526E0)); -#13562=LINE('',#13561,#13560); -#13563=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13564=VECTOR('',#13563,5.E-2); -#13565=CARTESIAN_POINT('',(5.75E0,1.55E0,7.450000071526E0)); -#13566=LINE('',#13565,#13564); -#13567=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13568=VECTOR('',#13567,5.E-2); -#13569=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.450000071526E0)); -#13570=LINE('',#13569,#13568); -#13571=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13572=VECTOR('',#13571,5.E-2); -#13573=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.900000071526E0)); -#13574=LINE('',#13573,#13572); -#13575=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13576=VECTOR('',#13575,5.E-2); -#13577=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.900000071526E0)); -#13578=LINE('',#13577,#13576); -#13579=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13580=VECTOR('',#13579,5.E-2); -#13581=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.768749928474E0)); -#13582=LINE('',#13581,#13580); -#13583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13584=VECTOR('',#13583,5.E-2); -#13585=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.450000071526E0)); -#13586=LINE('',#13585,#13584); -#13587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13588=VECTOR('',#13587,5.E-2); -#13589=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,7.450000071526E0)); -#13590=LINE('',#13589,#13588); -#13591=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13592=VECTOR('',#13591,5.E-2); -#13593=CARTESIAN_POINT('',(5.75E0,1.55E0,6.774999856949E0)); -#13594=LINE('',#13593,#13592); -#13595=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13596=VECTOR('',#13595,5.E-2); -#13597=CARTESIAN_POINT('',(5.75E0,1.55E0,6.887500071526E0)); -#13598=LINE('',#13597,#13596); -#13599=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13600=VECTOR('',#13599,5.E-2); -#13601=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.887500071526E0)); -#13602=LINE('',#13601,#13600); -#13603=DIRECTION('',(3.552713678800E-14,-1.E0,1.776356839400E-14)); -#13604=VECTOR('',#13603,5.E-2); -#13605=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,7.000000071526E0)); -#13606=LINE('',#13605,#13604); -#13607=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13608=VECTOR('',#13607,5.E-2); -#13609=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,7.000000071526E0)); -#13610=LINE('',#13609,#13608); -#13611=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13612=VECTOR('',#13611,5.E-2); -#13613=CARTESIAN_POINT('',(4.75E0,1.55E0,6.887500071526E0)); -#13614=LINE('',#13613,#13612); -#13615=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13616=VECTOR('',#13615,5.E-2); -#13617=CARTESIAN_POINT('',(4.75E0,1.55E0,6.774999856949E0)); -#13618=LINE('',#13617,#13616); -#13619=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13620=VECTOR('',#13619,5.E-2); -#13621=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.625E0)); -#13622=LINE('',#13621,#13620); -#13623=DIRECTION('',(3.552713678800E-14,-1.E0,0.E0)); -#13624=VECTOR('',#13623,5.E-2); -#13625=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.606249856949E0)); -#13626=LINE('',#13625,#13624); -#13627=DIRECTION('',(-1.776356839400E-14,-1.E0,0.E0)); -#13628=VECTOR('',#13627,5.E-2); -#13629=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,6.587500143051E0)); -#13630=LINE('',#13629,#13628); -#13631=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13632=VECTOR('',#13631,5.E-2); -#13633=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.549999856949E0)); -#13634=LINE('',#13633,#13632); -#13635=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13636=VECTOR('',#13635,5.E-2); -#13637=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.493749856949E0)); -#13638=LINE('',#13637,#13636); -#13639=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13640=VECTOR('',#13639,5.E-2); -#13641=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.4E0)); -#13642=LINE('',#13641,#13640); -#13643=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13644=VECTOR('',#13643,5.E-2); -#13645=CARTESIAN_POINT('',(4.75E0,1.55E0,6.2875E0)); -#13646=LINE('',#13645,#13644); -#13647=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13648=VECTOR('',#13647,5.E-2); -#13649=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.175E0)); -#13650=LINE('',#13649,#13648); -#13651=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13652=VECTOR('',#13651,5.E-2); -#13653=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.081250143051E0)); -#13654=LINE('',#13653,#13652); -#13655=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#13656=VECTOR('',#13655,5.E-2); -#13657=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.025000143051E0)); -#13658=LINE('',#13657,#13656); -#13659=DIRECTION('',(3.552713678800E-14,-1.E0,0.E0)); -#13660=VECTOR('',#13659,5.E-2); -#13661=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.987499856949E0)); -#13662=LINE('',#13661,#13660); -#13663=DIRECTION('',(-1.776356839400E-14,-1.E0,0.E0)); -#13664=VECTOR('',#13663,5.E-2); -#13665=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.968750143051E0)); -#13666=LINE('',#13665,#13664); -#13667=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13668=VECTOR('',#13667,5.E-2); -#13669=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.95E0)); -#13670=LINE('',#13669,#13668); -#13671=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13672=VECTOR('',#13671,5.E-2); -#13673=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.95E0)); -#13674=LINE('',#13673,#13672); -#13675=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13676=VECTOR('',#13675,5.E-2); -#13677=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.968750143051E0)); -#13678=LINE('',#13677,#13676); -#13679=DIRECTION('',(3.552713678800E-14,-1.E0,1.776356839400E-14)); -#13680=VECTOR('',#13679,5.E-2); -#13681=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.987499856949E0)); -#13682=LINE('',#13681,#13680); -#13683=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13684=VECTOR('',#13683,5.E-2); -#13685=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.025000143051E0)); -#13686=LINE('',#13685,#13684); -#13687=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13688=VECTOR('',#13687,5.E-2); -#13689=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.081250143051E0)); -#13690=LINE('',#13689,#13688); -#13691=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13692=VECTOR('',#13691,5.E-2); -#13693=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.175E0)); -#13694=LINE('',#13693,#13692); -#13695=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13696=VECTOR('',#13695,5.E-2); -#13697=CARTESIAN_POINT('',(5.75E0,1.55E0,6.2875E0)); -#13698=LINE('',#13697,#13696); -#13699=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13700=VECTOR('',#13699,5.E-2); -#13701=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.4E0)); -#13702=LINE('',#13701,#13700); -#13703=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13704=VECTOR('',#13703,5.E-2); -#13705=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.493749856949E0)); -#13706=LINE('',#13705,#13704); -#13707=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13708=VECTOR('',#13707,5.E-2); -#13709=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.549999856949E0)); -#13710=LINE('',#13709,#13708); -#13711=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13712=VECTOR('',#13711,5.E-2); -#13713=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,6.587500143051E0)); -#13714=LINE('',#13713,#13712); -#13715=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13716=VECTOR('',#13715,5.E-2); -#13717=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.606249856949E0)); -#13718=LINE('',#13717,#13716); -#13719=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13720=VECTOR('',#13719,5.E-2); -#13721=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,6.625E0)); -#13722=LINE('',#13721,#13720); -#13723=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13724=VECTOR('',#13723,5.E-2); -#13725=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.531250143051E0)); -#13726=LINE('',#13725,#13724); -#13727=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13728=VECTOR('',#13727,5.E-2); -#13729=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.531250143051E0)); -#13730=LINE('',#13729,#13728); -#13731=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13732=VECTOR('',#13731,5.E-2); -#13733=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.5125E0)); -#13734=LINE('',#13733,#13732); -#13735=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13736=VECTOR('',#13735,5.E-2); -#13737=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.437499856949E0)); -#13738=LINE('',#13737,#13736); -#13739=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13740=VECTOR('',#13739,5.E-2); -#13741=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.381249856949E0)); -#13742=LINE('',#13741,#13740); -#13743=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13744=VECTOR('',#13743,5.E-2); -#13745=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,6.2875E0)); -#13746=LINE('',#13745,#13744); -#13747=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#13748=VECTOR('',#13747,5.E-2); -#13749=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.193750143051E0)); -#13750=LINE('',#13749,#13748); -#13751=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13752=VECTOR('',#13751,5.E-2); -#13753=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.137500143051E0)); -#13754=LINE('',#13753,#13752); -#13755=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13756=VECTOR('',#13755,5.E-2); -#13757=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.0625E0)); -#13758=LINE('',#13757,#13756); -#13759=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13760=VECTOR('',#13759,5.E-2); -#13761=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.043749856949E0)); -#13762=LINE('',#13761,#13760); -#13763=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13764=VECTOR('',#13763,5.E-2); -#13765=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.043749856949E0)); -#13766=LINE('',#13765,#13764); -#13767=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13768=VECTOR('',#13767,5.E-2); -#13769=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.0625E0)); -#13770=LINE('',#13769,#13768); -#13771=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13772=VECTOR('',#13771,5.E-2); -#13773=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.137500143051E0)); -#13774=LINE('',#13773,#13772); -#13775=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13776=VECTOR('',#13775,5.E-2); -#13777=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.193750143051E0)); -#13778=LINE('',#13777,#13776); -#13779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13780=VECTOR('',#13779,5.E-2); -#13781=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.2875E0)); -#13782=LINE('',#13781,#13780); -#13783=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13784=VECTOR('',#13783,5.E-2); -#13785=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.381249856949E0)); -#13786=LINE('',#13785,#13784); -#13787=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13788=VECTOR('',#13787,5.E-2); -#13789=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.437499856949E0)); -#13790=LINE('',#13789,#13788); -#13791=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13792=VECTOR('',#13791,5.E-2); -#13793=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.5125E0)); -#13794=LINE('',#13793,#13792); -#13795=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13796=VECTOR('',#13795,5.E-2); -#13797=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.800000143051E0)); -#13798=LINE('',#13797,#13796); -#13799=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13800=VECTOR('',#13799,5.E-2); -#13801=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.78125E0)); -#13802=LINE('',#13801,#13800); -#13803=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#13804=VECTOR('',#13803,5.E-2); -#13805=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.762499856949E0)); -#13806=LINE('',#13805,#13804); -#13807=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13808=VECTOR('',#13807,5.E-2); -#13809=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.725E0)); -#13810=LINE('',#13809,#13808); -#13811=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13812=VECTOR('',#13811,5.E-2); -#13813=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.66875E0)); -#13814=LINE('',#13813,#13812); -#13815=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13816=VECTOR('',#13815,5.E-2); -#13817=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.575000143051E0)); -#13818=LINE('',#13817,#13816); -#13819=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13820=VECTOR('',#13819,5.E-2); -#13821=CARTESIAN_POINT('',(4.75E0,1.55E0,5.462500143051E0)); -#13822=LINE('',#13821,#13820); -#13823=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13824=VECTOR('',#13823,5.E-2); -#13825=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.350000143051E0)); -#13826=LINE('',#13825,#13824); -#13827=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13828=VECTOR('',#13827,5.E-2); -#13829=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.256249856949E0)); -#13830=LINE('',#13829,#13828); -#13831=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13832=VECTOR('',#13831,5.E-2); -#13833=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.199999856949E0)); -#13834=LINE('',#13833,#13832); -#13835=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13836=VECTOR('',#13835,5.E-2); -#13837=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.1625E0)); -#13838=LINE('',#13837,#13836); -#13839=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13840=VECTOR('',#13839,5.E-2); -#13841=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.143749856949E0)); -#13842=LINE('',#13841,#13840); -#13843=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13844=VECTOR('',#13843,5.E-2); -#13845=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.125000143051E0)); -#13846=LINE('',#13845,#13844); -#13847=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13848=VECTOR('',#13847,5.E-2); -#13849=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.125000143051E0)); -#13850=LINE('',#13849,#13848); -#13851=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13852=VECTOR('',#13851,5.E-2); -#13853=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.143749856949E0)); -#13854=LINE('',#13853,#13852); -#13855=DIRECTION('',(-1.776356839400E-14,-1.E0,0.E0)); -#13856=VECTOR('',#13855,5.E-2); -#13857=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.1625E0)); -#13858=LINE('',#13857,#13856); -#13859=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13860=VECTOR('',#13859,5.E-2); -#13861=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.199999856949E0)); -#13862=LINE('',#13861,#13860); -#13863=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13864=VECTOR('',#13863,5.E-2); -#13865=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.256249856949E0)); -#13866=LINE('',#13865,#13864); -#13867=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#13868=VECTOR('',#13867,5.E-2); -#13869=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.350000143051E0)); -#13870=LINE('',#13869,#13868); -#13871=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13872=VECTOR('',#13871,5.E-2); -#13873=CARTESIAN_POINT('',(5.75E0,1.55E0,5.462500143051E0)); -#13874=LINE('',#13873,#13872); -#13875=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13876=VECTOR('',#13875,5.E-2); -#13877=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.575000143051E0)); -#13878=LINE('',#13877,#13876); -#13879=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13880=VECTOR('',#13879,5.E-2); -#13881=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.66875E0)); -#13882=LINE('',#13881,#13880); -#13883=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13884=VECTOR('',#13883,5.E-2); -#13885=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.725E0)); -#13886=LINE('',#13885,#13884); -#13887=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#13888=VECTOR('',#13887,5.E-2); -#13889=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.762499856949E0)); -#13890=LINE('',#13889,#13888); -#13891=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13892=VECTOR('',#13891,5.E-2); -#13893=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.78125E0)); -#13894=LINE('',#13893,#13892); -#13895=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13896=VECTOR('',#13895,5.E-2); -#13897=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.800000143051E0)); -#13898=LINE('',#13897,#13896); -#13899=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13900=VECTOR('',#13899,5.E-2); -#13901=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.706249856949E0)); -#13902=LINE('',#13901,#13900); -#13903=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13904=VECTOR('',#13903,5.E-2); -#13905=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.706249856949E0)); -#13906=LINE('',#13905,#13904); -#13907=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13908=VECTOR('',#13907,5.E-2); -#13909=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.687500143051E0)); -#13910=LINE('',#13909,#13908); -#13911=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13912=VECTOR('',#13911,5.E-2); -#13913=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.6125E0)); -#13914=LINE('',#13913,#13912); -#13915=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13916=VECTOR('',#13915,5.E-2); -#13917=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.55625E0)); -#13918=LINE('',#13917,#13916); -#13919=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13920=VECTOR('',#13919,5.E-2); -#13921=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.462500143051E0)); -#13922=LINE('',#13921,#13920); -#13923=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#13924=VECTOR('',#13923,5.E-2); -#13925=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.368749856949E0)); -#13926=LINE('',#13925,#13924); -#13927=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13928=VECTOR('',#13927,5.E-2); -#13929=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.312499856949E0)); -#13930=LINE('',#13929,#13928); -#13931=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13932=VECTOR('',#13931,5.E-2); -#13933=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.237500143051E0)); -#13934=LINE('',#13933,#13932); -#13935=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13936=VECTOR('',#13935,5.E-2); -#13937=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.21875E0)); -#13938=LINE('',#13937,#13936); -#13939=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13940=VECTOR('',#13939,5.E-2); -#13941=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.21875E0)); -#13942=LINE('',#13941,#13940); -#13943=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13944=VECTOR('',#13943,5.E-2); -#13945=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.237500143051E0)); -#13946=LINE('',#13945,#13944); -#13947=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13948=VECTOR('',#13947,5.E-2); -#13949=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.312499856949E0)); -#13950=LINE('',#13949,#13948); -#13951=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13952=VECTOR('',#13951,5.E-2); -#13953=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.368749856949E0)); -#13954=LINE('',#13953,#13952); -#13955=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13956=VECTOR('',#13955,5.E-2); -#13957=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,5.462500143051E0)); -#13958=LINE('',#13957,#13956); -#13959=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13960=VECTOR('',#13959,5.E-2); -#13961=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.55625E0)); -#13962=LINE('',#13961,#13960); -#13963=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13964=VECTOR('',#13963,5.E-2); -#13965=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.6125E0)); -#13966=LINE('',#13965,#13964); -#13967=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13968=VECTOR('',#13967,5.E-2); -#13969=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.687500143051E0)); -#13970=LINE('',#13969,#13968); -#13971=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#13972=VECTOR('',#13971,5.E-2); -#13973=CARTESIAN_POINT('',(4.75E0,1.55E0,4.524999856949E0)); -#13974=LINE('',#13973,#13972); -#13975=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#13976=VECTOR('',#13975,5.E-2); -#13977=CARTESIAN_POINT('',(5.75E0,1.55E0,4.225000143051E0)); -#13978=LINE('',#13977,#13976); -#13979=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13980=VECTOR('',#13979,5.E-2); -#13981=CARTESIAN_POINT('',(5.75E0,1.55E0,4.337500143051E0)); -#13982=LINE('',#13981,#13980); -#13983=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13984=VECTOR('',#13983,5.E-2); -#13985=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.412499856949E0)); -#13986=LINE('',#13985,#13984); -#13987=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13988=VECTOR('',#13987,5.E-2); -#13989=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.787500143051E0)); -#13990=LINE('',#13989,#13988); -#13991=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13992=VECTOR('',#13991,5.E-2); -#13993=CARTESIAN_POINT('',(5.75E0,1.55E0,4.862499856949E0)); -#13994=LINE('',#13993,#13992); -#13995=DIRECTION('',(0.E0,-1.E0,0.E0)); -#13996=VECTOR('',#13995,5.E-2); -#13997=CARTESIAN_POINT('',(5.75E0,1.55E0,4.974999856949E0)); -#13998=LINE('',#13997,#13996); -#13999=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14000=VECTOR('',#13999,5.E-2); -#14001=CARTESIAN_POINT('',(4.75E0,1.55E0,4.675000143051E0)); -#14002=LINE('',#14001,#14000); -#14003=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14004=VECTOR('',#14003,5.E-2); -#14005=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,4.6E0)); -#14006=LINE('',#14005,#14004); -#14007=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#14008=VECTOR('',#14007,5.E-2); -#14009=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.76875E0)); -#14010=LINE('',#14009,#14008); -#14011=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14012=VECTOR('',#14011,5.E-2); -#14013=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.43125E0)); -#14014=LINE('',#14013,#14012); -#14015=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14016=VECTOR('',#14015,5.E-2); -#14017=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,3.8125E0)); -#14018=LINE('',#14017,#14016); -#14019=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14020=VECTOR('',#14019,5.E-2); -#14021=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,4.074999856949E0)); -#14022=LINE('',#14021,#14020); -#14023=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14024=VECTOR('',#14023,5.E-2); -#14025=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,4.074999856949E0)); -#14026=LINE('',#14025,#14024); -#14027=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14028=VECTOR('',#14027,5.E-2); -#14029=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,3.8125E0)); -#14030=LINE('',#14029,#14028); -#14031=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14032=VECTOR('',#14031,5.E-2); -#14033=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,3.08125E0)); -#14034=LINE('',#14033,#14032); -#14035=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14036=VECTOR('',#14035,5.E-2); -#14037=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,3.043749713898E0)); -#14038=LINE('',#14037,#14036); -#14039=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14040=VECTOR('',#14039,5.E-2); -#14041=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,2.987499713898E0)); -#14042=LINE('',#14041,#14040); -#14043=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14044=VECTOR('',#14043,5.E-2); -#14045=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,2.96875E0)); -#14046=LINE('',#14045,#14044); -#14047=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14048=VECTOR('',#14047,5.E-2); -#14049=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,2.96875E0)); -#14050=LINE('',#14049,#14048); -#14051=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14052=VECTOR('',#14051,5.E-2); -#14053=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,2.987499713898E0)); -#14054=LINE('',#14053,#14052); -#14055=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14056=VECTOR('',#14055,5.E-2); -#14057=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,3.043749713898E0)); -#14058=LINE('',#14057,#14056); -#14059=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14060=VECTOR('',#14059,5.E-2); -#14061=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,3.118750286102E0)); -#14062=LINE('',#14061,#14060); -#14063=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14064=VECTOR('',#14063,5.E-2); -#14065=CARTESIAN_POINT('',(5.75E0,1.55E0,3.212499713898E0)); -#14066=LINE('',#14065,#14064); -#14067=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14068=VECTOR('',#14067,5.E-2); -#14069=CARTESIAN_POINT('',(5.75E0,1.55E0,3.662500143051E0)); -#14070=LINE('',#14069,#14068); -#14071=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14072=VECTOR('',#14071,5.E-2); -#14073=CARTESIAN_POINT('',(4.75E0,1.55E0,3.662500143051E0)); -#14074=LINE('',#14073,#14072); -#14075=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14076=VECTOR('',#14075,5.E-2); -#14077=CARTESIAN_POINT('',(4.75E0,1.55E0,3.212499713898E0)); -#14078=LINE('',#14077,#14076); -#14079=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14080=VECTOR('',#14079,5.E-2); -#14081=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,3.118750286102E0)); -#14082=LINE('',#14081,#14080); -#14083=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14084=VECTOR('',#14083,5.E-2); -#14085=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,3.043749713898E0)); -#14086=LINE('',#14085,#14084); -#14087=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14088=VECTOR('',#14087,5.E-2); -#14089=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,2.987499713898E0)); -#14090=LINE('',#14089,#14088); -#14091=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14092=VECTOR('',#14091,5.E-2); -#14093=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.96875E0)); -#14094=LINE('',#14093,#14092); -#14095=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14096=VECTOR('',#14095,5.E-2); -#14097=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,2.96875E0)); -#14098=LINE('',#14097,#14096); -#14099=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14100=VECTOR('',#14099,5.E-2); -#14101=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,2.987499713898E0)); -#14102=LINE('',#14101,#14100); -#14103=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14104=VECTOR('',#14103,5.E-2); -#14105=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,3.043749713898E0)); -#14106=LINE('',#14105,#14104); -#14107=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14108=VECTOR('',#14107,5.E-2); -#14109=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.550000143051E0)); -#14110=LINE('',#14109,#14108); -#14111=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14112=VECTOR('',#14111,5.E-2); -#14113=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.550000143051E0)); -#14114=LINE('',#14113,#14112); -#14115=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14116=VECTOR('',#14115,5.E-2); -#14117=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.19375E0)); -#14118=LINE('',#14117,#14116); -#14119=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14120=VECTOR('',#14119,5.E-2); -#14121=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,3.1375E0)); -#14122=LINE('',#14121,#14120); -#14123=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14124=VECTOR('',#14123,5.E-2); -#14125=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,3.099999713898E0)); -#14126=LINE('',#14125,#14124); -#14127=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14128=VECTOR('',#14127,5.E-2); -#14129=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,3.08125E0)); -#14130=LINE('',#14129,#14128); -#14131=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14132=VECTOR('',#14131,5.E-2); -#14133=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,3.08125E0)); -#14134=LINE('',#14133,#14132); -#14135=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14136=VECTOR('',#14135,5.E-2); -#14137=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,3.099999713898E0)); -#14138=LINE('',#14137,#14136); -#14139=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14140=VECTOR('',#14139,5.E-2); -#14141=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,3.1375E0)); -#14142=LINE('',#14141,#14140); -#14143=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14144=VECTOR('',#14143,5.E-2); -#14145=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.19375E0)); -#14146=LINE('',#14145,#14144); -#14147=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14148=VECTOR('',#14147,5.E-2); -#14149=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,3.08125E0)); -#14150=LINE('',#14149,#14148); -#14151=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14152=VECTOR('',#14151,5.E-2); -#14153=CARTESIAN_POINT('',(5.367021262646E0,1.55E0,3.099999713898E0)); -#14154=LINE('',#14153,#14152); -#14155=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14156=VECTOR('',#14155,5.E-2); -#14157=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,3.1375E0)); -#14158=LINE('',#14157,#14156); -#14159=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14160=VECTOR('',#14159,5.E-2); -#14161=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.19375E0)); -#14162=LINE('',#14161,#14160); -#14163=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14164=VECTOR('',#14163,5.E-2); -#14165=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.550000143051E0)); -#14166=LINE('',#14165,#14164); -#14167=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14168=VECTOR('',#14167,5.E-2); -#14169=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.550000143051E0)); -#14170=LINE('',#14169,#14168); -#14171=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14172=VECTOR('',#14171,5.E-2); -#14173=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.19375E0)); -#14174=LINE('',#14173,#14172); -#14175=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14176=VECTOR('',#14175,5.E-2); -#14177=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,3.1375E0)); -#14178=LINE('',#14177,#14176); -#14179=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14180=VECTOR('',#14179,5.E-2); -#14181=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,3.099999713898E0)); -#14182=LINE('',#14181,#14180); -#14183=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14184=VECTOR('',#14183,5.E-2); -#14185=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,3.08125E0)); -#14186=LINE('',#14185,#14184); -#14187=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14188=VECTOR('',#14187,5.E-2); -#14189=CARTESIAN_POINT('',(4.75E0,1.55E0,2.106250286102E0)); -#14190=LINE('',#14189,#14188); -#14191=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14192=VECTOR('',#14191,5.E-2); -#14193=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.106250286102E0)); -#14194=LINE('',#14193,#14192); -#14195=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14196=VECTOR('',#14195,5.E-2); -#14197=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.40625E0)); -#14198=LINE('',#14197,#14196); -#14199=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14200=VECTOR('',#14199,5.E-2); -#14201=CARTESIAN_POINT('',(5.75E0,1.55E0,2.40625E0)); -#14202=LINE('',#14201,#14200); -#14203=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14204=VECTOR('',#14203,5.E-2); -#14205=CARTESIAN_POINT('',(5.75E0,1.55E0,2.51875E0)); -#14206=LINE('',#14205,#14204); -#14207=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14208=VECTOR('',#14207,5.E-2); -#14209=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.51875E0)); -#14210=LINE('',#14209,#14208); -#14211=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14212=VECTOR('',#14211,5.E-2); -#14213=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.818749713898E0)); -#14214=LINE('',#14213,#14212); -#14215=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14216=VECTOR('',#14215,5.E-2); -#14217=CARTESIAN_POINT('',(4.75E0,1.55E0,2.818749713898E0)); -#14218=LINE('',#14217,#14216); -#14219=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14220=VECTOR('',#14219,5.E-2); -#14221=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.806249713898E0)); -#14222=LINE('',#14221,#14220); -#14223=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14224=VECTOR('',#14223,5.E-2); -#14225=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.84375E0)); -#14226=LINE('',#14225,#14224); -#14227=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14228=VECTOR('',#14227,5.E-2); -#14229=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.9E0)); -#14230=LINE('',#14229,#14228); -#14231=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14232=VECTOR('',#14231,5.E-2); -#14233=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.937500286102E0)); -#14234=LINE('',#14233,#14232); -#14235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14236=VECTOR('',#14235,5.E-2); -#14237=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.937500286102E0)); -#14238=LINE('',#14237,#14236); -#14239=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14240=VECTOR('',#14239,5.E-2); -#14241=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.9E0)); -#14242=LINE('',#14241,#14240); -#14243=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14244=VECTOR('',#14243,5.E-2); -#14245=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.84375E0)); -#14246=LINE('',#14245,#14244); -#14247=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14248=VECTOR('',#14247,5.E-2); -#14249=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.749999713898E0)); -#14250=LINE('',#14249,#14248); -#14251=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14252=VECTOR('',#14251,5.E-2); -#14253=CARTESIAN_POINT('',(4.75E0,1.55E0,1.656250286102E0)); -#14254=LINE('',#14253,#14252); -#14255=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14256=VECTOR('',#14255,5.E-2); -#14257=CARTESIAN_POINT('',(4.75E0,1.55E0,1.581249713898E0)); -#14258=LINE('',#14257,#14256); -#14259=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14260=VECTOR('',#14259,5.E-2); -#14261=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.487500286102E0)); -#14262=LINE('',#14261,#14260); -#14263=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14264=VECTOR('',#14263,5.E-2); -#14265=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.39375E0)); -#14266=LINE('',#14265,#14264); -#14267=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14268=VECTOR('',#14267,5.E-2); -#14269=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.3375E0)); -#14270=LINE('',#14269,#14268); -#14271=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14272=VECTOR('',#14271,5.E-2); -#14273=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.299999713898E0)); -#14274=LINE('',#14273,#14272); -#14275=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14276=VECTOR('',#14275,5.E-2); -#14277=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.299999713898E0)); -#14278=LINE('',#14277,#14276); -#14279=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14280=VECTOR('',#14279,5.E-2); -#14281=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.3375E0)); -#14282=LINE('',#14281,#14280); -#14283=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14284=VECTOR('',#14283,5.E-2); -#14285=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.39375E0)); -#14286=LINE('',#14285,#14284); -#14287=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14288=VECTOR('',#14287,5.E-2); -#14289=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.431250286102E0)); -#14290=LINE('',#14289,#14288); -#14291=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14292=VECTOR('',#14291,5.E-2); -#14293=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.39375E0)); -#14294=LINE('',#14293,#14292); -#14295=DIRECTION('',(3.552713678800E-14,-1.E0,0.E0)); -#14296=VECTOR('',#14295,5.E-2); -#14297=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.318750286102E0)); -#14298=LINE('',#14297,#14296); -#14299=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14300=VECTOR('',#14299,5.E-2); -#14301=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.28125E0)); -#14302=LINE('',#14301,#14300); -#14303=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14304=VECTOR('',#14303,5.E-2); -#14305=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.28125E0)); -#14306=LINE('',#14305,#14304); -#14307=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14308=VECTOR('',#14307,5.E-2); -#14309=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.318750286102E0)); -#14310=LINE('',#14309,#14308); -#14311=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14312=VECTOR('',#14311,5.E-2); -#14313=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.375000286102E0)); -#14314=LINE('',#14313,#14312); -#14315=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14316=VECTOR('',#14315,5.E-2); -#14317=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.468749713898E0)); -#14318=LINE('',#14317,#14316); -#14319=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14320=VECTOR('',#14319,5.E-2); -#14321=CARTESIAN_POINT('',(5.75E0,1.55E0,1.5625E0)); -#14322=LINE('',#14321,#14320); -#14323=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14324=VECTOR('',#14323,5.E-2); -#14325=CARTESIAN_POINT('',(5.75E0,1.55E0,1.675E0)); -#14326=LINE('',#14325,#14324); -#14327=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14328=VECTOR('',#14327,5.E-2); -#14329=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.768750286102E0)); -#14330=LINE('',#14329,#14328); -#14331=DIRECTION('',(0.E0,-1.E0,1.332267629550E-14)); -#14332=VECTOR('',#14331,5.E-2); -#14333=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.862499713898E0)); -#14334=LINE('',#14333,#14332); -#14335=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14336=VECTOR('',#14335,5.E-2); -#14337=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.918749713898E0)); -#14338=LINE('',#14337,#14336); -#14339=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14340=VECTOR('',#14339,5.E-2); -#14341=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.95625E0)); -#14342=LINE('',#14341,#14340); -#14343=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14344=VECTOR('',#14343,5.E-2); -#14345=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.95625E0)); -#14346=LINE('',#14345,#14344); -#14347=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14348=VECTOR('',#14347,5.E-2); -#14349=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.918749713898E0)); -#14350=LINE('',#14349,#14348); -#14351=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14352=VECTOR('',#14351,5.E-2); -#14353=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.84375E0)); -#14354=LINE('',#14353,#14352); -#14355=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14356=VECTOR('',#14355,5.E-2); -#14357=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.656250286102E0)); -#14358=LINE('',#14357,#14356); -#14359=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14360=VECTOR('',#14359,5.E-2); -#14361=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.581249713898E0)); -#14362=LINE('',#14361,#14360); -#14363=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14364=VECTOR('',#14363,5.E-2); -#14365=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.50625E0)); -#14366=LINE('',#14365,#14364); -#14367=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14368=VECTOR('',#14367,5.E-2); -#14369=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.431250286102E0)); -#14370=LINE('',#14369,#14368); -#14371=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14372=VECTOR('',#14371,5.E-2); -#14373=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.375000286102E0)); -#14374=LINE('',#14373,#14372); -#14375=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14376=VECTOR('',#14375,5.E-2); -#14377=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.375000286102E0)); -#14378=LINE('',#14377,#14376); -#14379=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14380=VECTOR('',#14379,5.E-2); -#14381=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.431250286102E0)); -#14382=LINE('',#14381,#14380); -#14383=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14384=VECTOR('',#14383,5.E-2); -#14385=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.50625E0)); -#14386=LINE('',#14385,#14384); -#14387=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14388=VECTOR('',#14387,5.E-2); -#14389=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.581249713898E0)); -#14390=LINE('',#14389,#14388); -#14391=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14392=VECTOR('',#14391,5.E-2); -#14393=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.656250286102E0)); -#14394=LINE('',#14393,#14392); -#14395=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14396=VECTOR('',#14395,5.E-2); -#14397=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.73125E0)); -#14398=LINE('',#14397,#14396); -#14399=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14400=VECTOR('',#14399,5.E-2); -#14401=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.806249713898E0)); -#14402=LINE('',#14401,#14400); -#14403=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14404=VECTOR('',#14403,5.E-2); -#14405=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.862499713898E0)); -#14406=LINE('',#14405,#14404); -#14407=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14408=VECTOR('',#14407,5.E-2); -#14409=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.862499713898E0)); -#14410=LINE('',#14409,#14408); -#14411=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14412=VECTOR('',#14411,5.E-2); -#14413=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.806249713898E0)); -#14414=LINE('',#14413,#14412); -#14415=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14416=VECTOR('',#14415,5.E-2); -#14417=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.73125E0)); -#14418=LINE('',#14417,#14416); -#14419=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14420=VECTOR('',#14419,5.E-2); -#14421=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.581249713898E0)); -#14422=LINE('',#14421,#14420); -#14423=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14424=VECTOR('',#14423,5.E-2); -#14425=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.656250286102E0)); -#14426=LINE('',#14425,#14424); -#14427=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14428=VECTOR('',#14427,5.E-2); -#14429=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.73125E0)); -#14430=LINE('',#14429,#14428); -#14431=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14432=VECTOR('',#14431,5.E-2); -#14433=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.806249713898E0)); -#14434=LINE('',#14433,#14432); -#14435=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14436=VECTOR('',#14435,5.E-2); -#14437=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.84375E0)); -#14438=LINE('',#14437,#14436); -#14439=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14440=VECTOR('',#14439,5.E-2); -#14441=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.84375E0)); -#14442=LINE('',#14441,#14440); -#14443=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14444=VECTOR('',#14443,5.E-2); -#14445=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.806249713898E0)); -#14446=LINE('',#14445,#14444); -#14447=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14448=VECTOR('',#14447,5.E-2); -#14449=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.73125E0)); -#14450=LINE('',#14449,#14448); -#14451=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14452=VECTOR('',#14451,5.E-2); -#14453=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.656250286102E0)); -#14454=LINE('',#14453,#14452); -#14455=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14456=VECTOR('',#14455,5.E-2); -#14457=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.581249713898E0)); -#14458=LINE('',#14457,#14456); -#14459=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14460=VECTOR('',#14459,5.E-2); -#14461=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.50625E0)); -#14462=LINE('',#14461,#14460); -#14463=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14464=VECTOR('',#14463,5.E-2); -#14465=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.431250286102E0)); -#14466=LINE('',#14465,#14464); -#14467=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14468=VECTOR('',#14467,5.E-2); -#14469=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.39375E0)); -#14470=LINE('',#14469,#14468); -#14471=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14472=VECTOR('',#14471,5.E-2); -#14473=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.39375E0)); -#14474=LINE('',#14473,#14472); -#14475=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14476=VECTOR('',#14475,5.E-2); -#14477=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.431250286102E0)); -#14478=LINE('',#14477,#14476); -#14479=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14480=VECTOR('',#14479,5.E-2); -#14481=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.50625E0)); -#14482=LINE('',#14481,#14480); -#14483=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14484=VECTOR('',#14483,5.E-2); -#14485=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.124997138977E-1)); -#14486=LINE('',#14485,#14484); -#14487=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14488=VECTOR('',#14487,5.E-2); -#14489=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,5.687497138977E-1)); -#14490=LINE('',#14489,#14488); -#14491=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14492=VECTOR('',#14491,5.E-2); -#14493=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.437502861023E-1)); -#14494=LINE('',#14493,#14492); -#14495=DIRECTION('',(0.E0,-1.E0,1.110223024625E-14)); -#14496=VECTOR('',#14495,5.E-2); -#14497=CARTESIAN_POINT('',(5.75E0,1.55E0,7.1875E-1)); -#14498=LINE('',#14497,#14496); -#14499=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14500=VECTOR('',#14499,5.E-2); -#14501=CARTESIAN_POINT('',(5.75E0,1.55E0,8.687502861023E-1)); -#14502=LINE('',#14501,#14500); -#14503=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14504=VECTOR('',#14503,5.E-2); -#14505=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.4375E-1)); -#14506=LINE('',#14505,#14504); -#14507=DIRECTION('',(0.E0,-1.E0,1.332267629550E-14)); -#14508=VECTOR('',#14507,5.E-2); -#14509=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.018749713898E0)); -#14510=LINE('',#14509,#14508); -#14511=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14512=VECTOR('',#14511,5.E-2); -#14513=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.074999713898E0)); -#14514=LINE('',#14513,#14512); -#14515=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14516=VECTOR('',#14515,5.E-2); -#14517=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.1125E0)); -#14518=LINE('',#14517,#14516); -#14519=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14520=VECTOR('',#14519,5.E-2); -#14521=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.131249713898E0)); -#14522=LINE('',#14521,#14520); -#14523=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14524=VECTOR('',#14523,5.E-2); -#14525=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.037500286102E0)); -#14526=LINE('',#14525,#14524); -#14527=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14528=VECTOR('',#14527,5.E-2); -#14529=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.018749713898E0)); -#14530=LINE('',#14529,#14528); -#14531=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14532=VECTOR('',#14531,5.E-2); -#14533=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.812502861023E-1)); -#14534=LINE('',#14533,#14532); -#14535=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14536=VECTOR('',#14535,5.E-2); -#14537=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.4375E-1)); -#14538=LINE('',#14537,#14536); -#14539=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14540=VECTOR('',#14539,5.E-2); -#14541=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.499997138977E-1)); -#14542=LINE('',#14541,#14540); -#14543=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14544=VECTOR('',#14543,5.E-2); -#14545=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,7.374997138977E-1)); -#14546=LINE('',#14545,#14544); -#14547=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14548=VECTOR('',#14547,5.E-2); -#14549=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.437502861023E-1)); -#14550=LINE('',#14549,#14548); -#14551=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14552=VECTOR('',#14551,5.E-2); -#14553=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.0625E-1)); -#14554=LINE('',#14553,#14552); -#14555=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14556=VECTOR('',#14555,5.E-2); -#14557=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,5.687497138977E-1)); -#14558=LINE('',#14557,#14556); -#14559=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14560=VECTOR('',#14559,5.E-2); -#14561=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.5E-1)); -#14562=LINE('',#14561,#14560); -#14563=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14564=VECTOR('',#14563,5.E-2); -#14565=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,5.5E-1)); -#14566=LINE('',#14565,#14564); -#14567=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14568=VECTOR('',#14567,5.E-2); -#14569=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.875002861023E-1)); -#14570=LINE('',#14569,#14568); -#14571=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14572=VECTOR('',#14571,5.E-2); -#14573=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,6.437502861023E-1)); -#14574=LINE('',#14573,#14572); -#14575=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14576=VECTOR('',#14575,5.E-2); -#14577=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,7.562502861023E-1)); -#14578=LINE('',#14577,#14576); -#14579=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14580=VECTOR('',#14579,5.E-2); -#14581=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,8.3125E-1)); -#14582=LINE('',#14581,#14580); -#14583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14584=VECTOR('',#14583,5.E-2); -#14585=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,8.3125E-1)); -#14586=LINE('',#14585,#14584); -#14587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14588=VECTOR('',#14587,5.E-2); -#14589=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,7.562502861023E-1)); -#14590=LINE('',#14589,#14588); -#14591=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14592=VECTOR('',#14591,5.E-2); -#14593=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.437502861023E-1)); -#14594=LINE('',#14593,#14592); -#14595=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14596=VECTOR('',#14595,5.E-2); -#14597=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,6.0625E-1)); -#14598=LINE('',#14597,#14596); -#14599=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14600=VECTOR('',#14599,5.E-2); -#14601=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,5.687497138977E-1)); -#14602=LINE('',#14601,#14600); -#14603=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#14604=VECTOR('',#14603,5.E-2); -#14605=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.687497138977E-1)); -#14606=LINE('',#14605,#14604); -#14607=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14608=VECTOR('',#14607,5.E-2); -#14609=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.0625E-1)); -#14610=LINE('',#14609,#14608); -#14611=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14612=VECTOR('',#14611,5.E-2); -#14613=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.625E-1)); -#14614=LINE('',#14613,#14612); -#14615=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14616=VECTOR('',#14615,5.E-2); -#14617=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,7.562502861023E-1)); -#14618=LINE('',#14617,#14616); -#14619=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14620=VECTOR('',#14619,5.E-2); -#14621=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,8.3125E-1)); -#14622=LINE('',#14621,#14620); -#14623=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14624=VECTOR('',#14623,5.E-2); -#14625=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.250002861023E-1)); -#14626=LINE('',#14625,#14624); -#14627=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14628=VECTOR('',#14627,5.E-2); -#14629=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,9.812502861023E-1)); -#14630=LINE('',#14629,#14628); -#14631=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14632=VECTOR('',#14631,5.E-2); -#14633=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.018749713898E0)); -#14634=LINE('',#14633,#14632); -#14635=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14636=VECTOR('',#14635,5.E-2); -#14637=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.1125E0)); -#14638=LINE('',#14637,#14636); -#14639=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14640=VECTOR('',#14639,5.E-2); -#14641=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.093750286102E0)); -#14642=LINE('',#14641,#14640); -#14643=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14644=VECTOR('',#14643,5.E-2); -#14645=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.018749713898E0)); -#14646=LINE('',#14645,#14644); -#14647=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14648=VECTOR('',#14647,5.E-2); -#14649=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.4375E-1)); -#14650=LINE('',#14649,#14648); -#14651=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14652=VECTOR('',#14651,5.E-2); -#14653=CARTESIAN_POINT('',(4.75E0,1.55E0,8.125002861023E-1)); -#14654=LINE('',#14653,#14652); -#14655=DIRECTION('',(0.E0,-1.E0,1.332267629550E-14)); -#14656=VECTOR('',#14655,5.E-2); -#14657=CARTESIAN_POINT('',(4.75E0,1.55E0,7.75E-1)); -#14658=LINE('',#14657,#14656); -#14659=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14660=VECTOR('',#14659,5.E-2); -#14661=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.437502861023E-1)); -#14662=LINE('',#14661,#14660); -#14663=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14664=VECTOR('',#14663,5.E-2); -#14665=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,5.687497138977E-1)); -#14666=LINE('',#14665,#14664); -#14667=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14668=VECTOR('',#14667,5.E-2); -#14669=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,4.9375E-1)); -#14670=LINE('',#14669,#14668); -#14671=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14672=VECTOR('',#14671,5.E-2); -#14673=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,4.750002861023E-1)); -#14674=LINE('',#14673,#14672); -#14675=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14676=VECTOR('',#14675,5.E-2); -#14677=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,4.750002861023E-1)); -#14678=LINE('',#14677,#14676); -#14679=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14680=VECTOR('',#14679,5.E-2); -#14681=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,4.9375E-1)); -#14682=LINE('',#14681,#14680); -#14683=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14684=VECTOR('',#14683,5.E-2); -#14685=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.312502861023E-1)); -#14686=LINE('',#14685,#14684); -#14687=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14688=VECTOR('',#14687,5.E-2); -#14689=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,6.0625E-1)); -#14690=LINE('',#14689,#14688); -#14691=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14692=VECTOR('',#14691,5.E-2); -#14693=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,5.124997138977E-1)); -#14694=LINE('',#14693,#14692); -#14695=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14696=VECTOR('',#14695,5.E-2); -#14697=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,4.750002861023E-1)); -#14698=LINE('',#14697,#14696); -#14699=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14700=VECTOR('',#14699,5.E-2); -#14701=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,4.562497138977E-1)); -#14702=LINE('',#14701,#14700); -#14703=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14704=VECTOR('',#14703,5.E-2); -#14705=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,4.562497138977E-1)); -#14706=LINE('',#14705,#14704); -#14707=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14708=VECTOR('',#14707,5.E-2); -#14709=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,4.750002861023E-1)); -#14710=LINE('',#14709,#14708); -#14711=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14712=VECTOR('',#14711,5.E-2); -#14713=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,3.062502861023E-1)); -#14714=LINE('',#14713,#14712); -#14715=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14716=VECTOR('',#14715,5.E-2); -#14717=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-2.187502861023E-1)); -#14718=LINE('',#14717,#14716); -#14719=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14720=VECTOR('',#14719,5.E-2); -#14721=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-2.562497138977E-1)); -#14722=LINE('',#14721,#14720); -#14723=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14724=VECTOR('',#14723,5.E-2); -#14725=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-2.562497138977E-1)); -#14726=LINE('',#14725,#14724); -#14727=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14728=VECTOR('',#14727,5.E-2); -#14729=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,-2.187502861023E-1)); -#14730=LINE('',#14729,#14728); -#14731=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14732=VECTOR('',#14731,5.E-2); -#14733=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,-1.625002861023E-1)); -#14734=LINE('',#14733,#14732); -#14735=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14736=VECTOR('',#14735,5.E-2); -#14737=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,-6.875E-2)); -#14738=LINE('',#14737,#14736); -#14739=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14740=VECTOR('',#14739,5.E-2); -#14741=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.249713897704E-3)); -#14742=LINE('',#14741,#14740); -#14743=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14744=VECTOR('',#14743,5.E-2); -#14745=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.E-1)); -#14746=LINE('',#14745,#14744); -#14747=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14748=VECTOR('',#14747,5.E-2); -#14749=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,1.5625E-1)); -#14750=LINE('',#14749,#14748); -#14751=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14752=VECTOR('',#14751,5.E-2); -#14753=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.937502861023E-1)); -#14754=LINE('',#14753,#14752); -#14755=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14756=VECTOR('',#14755,5.E-2); -#14757=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.874997138977E-1)); -#14758=LINE('',#14757,#14756); -#14759=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14760=VECTOR('',#14759,5.E-2); -#14761=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,2.6875E-1)); -#14762=LINE('',#14761,#14760); -#14763=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14764=VECTOR('',#14763,5.E-2); -#14765=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.937502861023E-1)); -#14766=LINE('',#14765,#14764); -#14767=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14768=VECTOR('',#14767,5.E-2); -#14769=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.187497138977E-1)); -#14770=LINE('',#14769,#14768); -#14771=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14772=VECTOR('',#14771,5.E-2); -#14773=CARTESIAN_POINT('',(4.75E0,1.55E0,-1.25E-2)); -#14774=LINE('',#14773,#14772); -#14775=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14776=VECTOR('',#14775,5.E-2); -#14777=CARTESIAN_POINT('',(4.75E0,1.55E0,-8.749971389771E-2)); -#14778=LINE('',#14777,#14776); -#14779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14780=VECTOR('',#14779,5.E-2); -#14781=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,-1.999997138977E-1)); -#14782=LINE('',#14781,#14780); -#14783=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14784=VECTOR('',#14783,5.E-2); -#14785=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,-2.750002861023E-1)); -#14786=LINE('',#14785,#14784); -#14787=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14788=VECTOR('',#14787,5.E-2); -#14789=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,-3.5E-1)); -#14790=LINE('',#14789,#14788); -#14791=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14792=VECTOR('',#14791,5.E-2); -#14793=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-3.687497138977E-1)); -#14794=LINE('',#14793,#14792); -#14795=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14796=VECTOR('',#14795,5.E-2); -#14797=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-3.687497138977E-1)); -#14798=LINE('',#14797,#14796); -#14799=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14800=VECTOR('',#14799,5.E-2); -#14801=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-3.5E-1)); -#14802=LINE('',#14801,#14800); -#14803=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14804=VECTOR('',#14803,5.E-2); -#14805=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,-3.124997138977E-1)); -#14806=LINE('',#14805,#14804); -#14807=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14808=VECTOR('',#14807,5.E-2); -#14809=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.5625E-1)); -#14810=LINE('',#14809,#14808); -#14811=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14812=VECTOR('',#14811,5.E-2); -#14813=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,-3.687497138977E-1)); -#14814=LINE('',#14813,#14812); -#14815=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14816=VECTOR('',#14815,5.E-2); -#14817=CARTESIAN_POINT('',(5.75E0,1.55E0,-3.687497138977E-1)); -#14818=LINE('',#14817,#14816); -#14819=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14820=VECTOR('',#14819,5.E-2); -#14821=CARTESIAN_POINT('',(5.75E0,1.55E0,3.062502861023E-1)); -#14822=LINE('',#14821,#14820); -#14823=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14824=VECTOR('',#14823,1.E-2); -#14825=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,7.509479917553E-1)); -#14826=LINE('',#14825,#14824); -#14827=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14828=VECTOR('',#14827,1.E-2); -#14829=CARTESIAN_POINT('',(-3.418216415891E0,1.55E0,3.485781583319E-1)); -#14830=LINE('',#14829,#14828); -#14831=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14832=VECTOR('',#14831,1.E-2); -#14833=CARTESIAN_POINT('',(-2.429572153713E0,1.55E0,8.657433522519E-2)); -#14834=LINE('',#14833,#14832); -#14835=DIRECTION('',(0.E0,-1.E0,0.E0)); -#14836=VECTOR('',#14835,1.E-2); -#14837=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,9.019260237562E-2)); -#14838=LINE('',#14837,#14836); -#14839=DIRECTION('',(0.E0,0.E0,-1.E0)); -#14840=VECTOR('',#14839,6.607553893797E-1); -#14841=CARTESIAN_POINT('',(-2.309434639741E0,1.54E0,7.509479917553E-1)); -#14842=LINE('',#14841,#14840); -#14843=CARTESIAN_POINT('',(-3.418216415891E0,1.54E0,3.485781583319E-1)); -#14844=CARTESIAN_POINT('',(-3.048622490508E0,1.54E0,4.827014361397E-1)); -#14845=CARTESIAN_POINT('',(-2.679028565125E0,1.54E0,6.168247139475E-1)); -#14846=CARTESIAN_POINT('',(-2.309434639741E0,1.54E0,7.509479917553E-1)); -#14848=CARTESIAN_POINT('',(-2.429572153713E0,1.54E0,8.657433522519E-2)); -#14849=CARTESIAN_POINT('',(-2.546324832949E0,1.54E0,8.770091901078E-2)); -#14850=CARTESIAN_POINT('',(-2.774383252738E0,1.54E0,1.062811465330E-1)); -#14851=CARTESIAN_POINT('',(-3.108900823435E0,1.54E0,1.949327331270E-1)); -#14852=CARTESIAN_POINT('',(-3.316229164484E0,1.54E0,2.917357635001E-1)); -#14853=CARTESIAN_POINT('',(-3.418216415891E0,1.54E0,3.485781583319E-1)); -#14855=CARTESIAN_POINT('',(-2.309434639741E0,1.54E0,9.019260237562E-2)); -#14856=CARTESIAN_POINT('',(-2.322772147471E0,1.54E0,8.938882588201E-2)); -#14857=CARTESIAN_POINT('',(-2.349448326548E0,1.54E0,8.804870970072E-2)); -#14858=CARTESIAN_POINT('',(-2.389501970825E0,1.54E0,8.684238554311E-2)); -#14859=CARTESIAN_POINT('',(-2.416210448397E0,1.54E0,8.657467796390E-2)); -#14860=CARTESIAN_POINT('',(-2.429572153713E0,1.54E0,8.657433522519E-2)); -#14862=CARTESIAN_POINT('',(-1.355854930280E0,1.54E0,3.765777389509E0)); -#14863=CARTESIAN_POINT('',(-1.238595103198E0,1.54E0,3.688808300316E0)); -#14864=CARTESIAN_POINT('',(-1.022070928953E0,1.54E0,3.519467320563E0)); -#14865=CARTESIAN_POINT('',(-7.622795865223E-1,1.54E0,3.204305359310E0)); -#14866=CARTESIAN_POINT('',(-5.737617442267E-1,1.54E0,2.852856095504E0)); -#14867=CARTESIAN_POINT('',(-4.587233502244E-1,1.54E0,2.473154193031E0)); -#14868=CARTESIAN_POINT('',(-4.206251047483E-1,1.54E0,2.080943871044E0)); -#14869=CARTESIAN_POINT('',(-4.594562146907E-1,1.54E0,1.688998689711E0)); -#14870=CARTESIAN_POINT('',(-5.749895968984E-1,1.54E0,1.309952967809E0)); -#14871=CARTESIAN_POINT('',(-7.636677122414E-1,1.54E0,9.594500467100E-1)); -#14872=CARTESIAN_POINT('',(-1.023079524938E0,1.54E0,6.453710459650E-1)); -#14873=CARTESIAN_POINT('',(-1.238984642817E0,1.54E0,4.765898563533E-1)); -#14874=CARTESIAN_POINT('',(-1.355854930280E0,1.54E0,3.999217256483E-1)); -#14876=DIRECTION('',(0.E0,0.E0,1.E0)); -#14877=VECTOR('',#14876,3.365855663861E0); -#14878=CARTESIAN_POINT('',(-1.355854930280E0,1.54E0,3.999217256483E-1)); -#14879=LINE('',#14878,#14877); -#14880=CARTESIAN_POINT('',(-2.705883122562E0,1.54E0,4.059909751877E0)); -#14881=CARTESIAN_POINT('',(-2.732942410469E0,1.54E0,4.071744299724E0)); -#14882=CARTESIAN_POINT('',(-2.786478319988E0,1.54E0,4.111684285312E0)); -#14883=CARTESIAN_POINT('',(-2.842964704605E0,1.54E0,4.194760630358E0)); -#14884=CARTESIAN_POINT('',(-2.884363683665E0,1.54E0,4.287845204590E0)); -#14885=CARTESIAN_POINT('',(-2.914885019781E0,1.54E0,4.375596147512E0)); -#14886=CARTESIAN_POINT('',(-2.940504397788E0,1.54E0,4.455778808010E0)); -#14887=CARTESIAN_POINT('',(-2.963736274210E0,1.54E0,4.525419954314E0)); -#14888=CARTESIAN_POINT('',(-2.990108794848E0,1.54E0,4.586877566231E0)); -#14889=CARTESIAN_POINT('',(-3.022737030265E0,1.54E0,4.636243139881E0)); -#14890=CARTESIAN_POINT('',(-3.065917078232E0,1.54E0,4.670416877497E0)); -#14891=CARTESIAN_POINT('',(-3.116627615079E0,1.54E0,4.679212470761E0)); -#14892=CARTESIAN_POINT('',(-3.164716940033E0,1.54E0,4.662778200878E0)); -#14893=CARTESIAN_POINT('',(-3.207010146779E0,1.54E0,4.629197867869E0)); -#14894=CARTESIAN_POINT('',(-3.240627301698E0,1.54E0,4.585360822888E0)); -#14895=CARTESIAN_POINT('',(-3.263425109942E0,1.54E0,4.536678364466E0)); -#14896=CARTESIAN_POINT('',(-3.272148755802E0,1.54E0,4.489539165406E0)); -#14897=CARTESIAN_POINT('',(-3.263041702391E0,1.54E0,4.445753294666E0)); -#14898=CARTESIAN_POINT('',(-3.233551737216E0,1.54E0,4.418493178925E0)); -#14899=CARTESIAN_POINT('',(-3.196008723068E0,1.54E0,4.409848993101E0)); -#14900=CARTESIAN_POINT('',(-3.170701330978E0,1.54E0,4.410834700981E0)); -#14901=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,4.412619339018E0)); -#14903=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.941801323147E0)); -#14904=CARTESIAN_POINT('',(-3.108507370770E0,1.54E0,3.960770940436E0)); -#14905=CARTESIAN_POINT('',(-3.010566019986E0,1.54E0,3.994843097695E0)); -#14906=CARTESIAN_POINT('',(-2.859684165553E0,1.54E0,4.034330233211E0)); -#14907=CARTESIAN_POINT('',(-2.757608330667E0,1.54E0,4.052604368656E0)); -#14908=CARTESIAN_POINT('',(-2.705883122562E0,1.54E0,4.059909751877E0)); -#14910=DIRECTION('',(0.E0,0.E0,-1.E0)); -#14911=VECTOR('',#14910,4.708180158703E-1); -#14912=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,4.412619339018E0)); -#14913=LINE('',#14912,#14911); -#14914=CARTESIAN_POINT('',(-2.575625748121E0,1.54E0,6.119789271963E0)); -#14915=CARTESIAN_POINT('',(-2.898564208026E0,1.54E0,6.117054664482E0)); -#14916=CARTESIAN_POINT('',(-3.221502667931E0,1.54E0,6.114320057001E0)); -#14917=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,6.111585449519E0)); -#14919=CARTESIAN_POINT('',(-3.544453866691E0,1.54E0,5.756586997800E0)); -#14920=CARTESIAN_POINT('',(-3.221511160501E0,1.54E0,5.877654422521E0)); -#14921=CARTESIAN_POINT('',(-2.898568454311E0,1.54E0,5.998721847242E0)); -#14922=CARTESIAN_POINT('',(-2.575625748121E0,1.54E0,6.119789271963E0)); -#14924=DIRECTION('',(0.E0,0.E0,1.E0)); -#14925=VECTOR('',#14924,5.170593332799E-1); -#14926=CARTESIAN_POINT('',(-3.544453866691E0,1.54E0,5.239527664520E0)); -#14927=LINE('',#14926,#14925); -#14928=CARTESIAN_POINT('',(-1.923218042121E0,1.54E0,5.825383145660E0)); -#14929=CARTESIAN_POINT('',(-2.463629983644E0,1.54E0,5.630097985280E0)); -#14930=CARTESIAN_POINT('',(-3.004041925168E0,1.54E0,5.434812824900E0)); -#14931=CARTESIAN_POINT('',(-3.544453866691E0,1.54E0,5.239527664520E0)); -#14933=DIRECTION('',(0.E0,0.E0,-1.E0)); -#14934=VECTOR('',#14933,7.896418426795E-1); -#14935=CARTESIAN_POINT('',(-1.923218042121E0,1.54E0,6.615024988339E0)); -#14936=LINE('',#14935,#14934); -#14937=DIRECTION('',(9.999979297889E-1,0.E0,-2.034801677748E-3)); -#14938=VECTOR('',#14937,9.515944181204E-1); -#14939=CARTESIAN_POINT('',(-2.874810490240E0,1.54E0,6.616961294258E0)); -#14940=LINE('',#14939,#14938); -#14941=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,6.967587730580E0)); -#14942=CARTESIAN_POINT('',(-2.240432509967E0,1.54E0,6.850712251806E0)); -#14943=CARTESIAN_POINT('',(-2.557621500104E0,1.54E0,6.733836773032E0)); -#14944=CARTESIAN_POINT('',(-2.874810490240E0,1.54E0,6.616961294258E0)); -#14946=DIRECTION('',(0.E0,0.E0,-1.E0)); -#14947=VECTOR('',#14946,5.221379787490E-1); -#14948=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,7.489725709329E0)); -#14949=LINE('',#14948,#14947); -#14950=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,6.898362595182E0)); -#14951=CARTESIAN_POINT('',(-3.004041925168E0,1.54E0,7.095483633231E0)); -#14952=CARTESIAN_POINT('',(-2.463642722499E0,1.54E0,7.292604671280E0)); -#14953=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,7.489725709329E0)); -#14955=DIRECTION('',(0.E0,0.E0,1.E0)); -#14956=VECTOR('',#14955,7.867771456628E-1); -#14957=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,6.111585449519E0)); -#14958=LINE('',#14957,#14956); -#14959=CARTESIAN_POINT('',(-3.239727722762E0,1.54E0,7.911611100185E0)); -#14960=CARTESIAN_POINT('',(-2.990233006644E0,1.54E0,7.963561839887E0)); -#14961=CARTESIAN_POINT('',(-2.740738290526E0,1.54E0,8.015512579589E0)); -#14962=CARTESIAN_POINT('',(-2.491243574408E0,1.54E0,8.067463319291E0)); -#14964=CARTESIAN_POINT('',(-2.491243574408E0,1.54E0,8.312648204863E0)); -#14965=CARTESIAN_POINT('',(-2.740738290526E0,1.54E0,8.178969169970E0)); -#14966=CARTESIAN_POINT('',(-2.990233006644E0,1.54E0,8.045290135078E0)); -#14967=CARTESIAN_POINT('',(-3.239727722762E0,1.54E0,7.911611100185E0)); -#14969=DIRECTION('',(0.E0,0.E0,1.E0)); -#14970=VECTOR('',#14969,2.451848855720E-1); -#14971=CARTESIAN_POINT('',(-2.491243574408E0,1.54E0,8.067463319291E0)); -#14972=LINE('',#14971,#14970); -#14973=DIRECTION('',(-1.577221316427E-3,0.E0,-9.999987561857E-1)); -#14974=VECTOR('',#14973,6.299881052683E-1); -#14975=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,9.242286387282E0)); -#14976=LINE('',#14975,#14974); -#14977=CARTESIAN_POINT('',(-3.544428388982E0,1.54E0,8.226771904890E0)); -#14978=CARTESIAN_POINT('',(-3.004033432598E0,1.54E0,8.565276732354E0)); -#14979=CARTESIAN_POINT('',(-2.463638476214E0,1.54E0,8.903781559818E0)); -#14980=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,9.242286387282E0)); -#14982=DIRECTION('',(0.E0,0.E0,1.E0)); -#14983=VECTOR('',#14982,8.351823564918E-1); -#14984=CARTESIAN_POINT('',(-3.544428388982E0,1.54E0,7.391589548398E0)); -#14985=LINE('',#14984,#14983); -#14986=CARTESIAN_POINT('',(-1.923307214104E0,1.54E0,7.560244033212E0)); -#14987=CARTESIAN_POINT('',(-2.463680939063E0,1.54E0,7.504025871607E0)); -#14988=CARTESIAN_POINT('',(-3.004054664022E0,1.54E0,7.447807710003E0)); -#14989=CARTESIAN_POINT('',(-3.544428388982E0,1.54E0,7.391589548398E0)); -#14991=DIRECTION('',(0.E0,0.E0,-1.E0)); -#14992=VECTOR('',#14991,6.267625716583E-1); -#14993=CARTESIAN_POINT('',(-1.923307214104E0,1.54E0,8.187006604870E0)); -#14994=LINE('',#14993,#14992); -#14995=CARTESIAN_POINT('',(-2.175065200079E0,1.54E0,8.141267173208E0)); -#14996=CARTESIAN_POINT('',(-2.091145871421E0,1.54E0,8.156513650429E0)); -#14997=CARTESIAN_POINT('',(-2.007226542762E0,1.54E0,8.171760127649E0)); -#14998=CARTESIAN_POINT('',(-1.923307214104E0,1.54E0,8.187006604870E0)); -#15000=DIRECTION('',(6.593263280459E-3,0.E0,-9.999782642034E-1)); -#15001=VECTOR('',#15000,3.361856835150E-1); -#15002=CARTESIAN_POINT('',(-2.177281760801E0,1.54E0,8.477445549459E0)); -#15003=LINE('',#15002,#15001); -#15004=CARTESIAN_POINT('',(-1.924237150499E0,1.54E0,8.612299065602E0)); -#15005=CARTESIAN_POINT('',(-2.008585353933E0,1.54E0,8.567347893554E0)); -#15006=CARTESIAN_POINT('',(-2.092933557367E0,1.54E0,8.522396721507E0)); -#15007=CARTESIAN_POINT('',(-2.177281760801E0,1.54E0,8.477445549459E0)); -#15009=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15010=VECTOR('',#15009,6.119283121188E-1); -#15011=CARTESIAN_POINT('',(-1.923192564412E0,1.54E0,1.037838840728E1)); -#15012=LINE('',#15011,#15010); -#15013=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,9.792991750417E0)); -#15014=CARTESIAN_POINT('',(-3.004024940028E0,1.54E0,9.988123969370E0)); -#15015=CARTESIAN_POINT('',(-2.463608752220E0,1.54E0,1.018325618832E1)); -#15016=CARTESIAN_POINT('',(-1.923192564412E0,1.54E0,1.037838840728E1)); -#15018=DIRECTION('',(-5.670519560583E-4,0.E0,9.999998392260E-1)); -#15019=VECTOR('',#15018,1.258043212979E0); -#15020=CARTESIAN_POINT('',(-3.543727751972E0,1.54E0,8.534948739698E0)); -#15021=LINE('',#15020,#15019); -#15022=CARTESIAN_POINT('',(-3.156950644744E0,1.54E0,8.677888105413E0)); -#15023=CARTESIAN_POINT('',(-3.285876347153E0,1.54E0,8.630241650174E0)); -#15024=CARTESIAN_POINT('',(-3.414802049562E0,1.54E0,8.582595194936E0)); -#15025=CARTESIAN_POINT('',(-3.543727751972E0,1.54E0,8.534948739698E0)); -#15027=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15028=VECTOR('',#15027,6.280568557938E-1); -#15029=CARTESIAN_POINT('',(-3.156950644744E0,1.54E0,9.305944961207E0)); -#15030=LINE('',#15029,#15028); -#15031=CARTESIAN_POINT('',(-2.917523870145E0,1.54E0,9.402006225147E0)); -#15032=CARTESIAN_POINT('',(-2.997332795011E0,1.54E0,9.369985803834E0)); -#15033=CARTESIAN_POINT('',(-3.077141719877E0,1.54E0,9.337965382520E0)); -#15034=CARTESIAN_POINT('',(-3.156950644744E0,1.54E0,9.305944961207E0)); -#15036=DIRECTION('',(0.E0,0.E0,1.E0)); -#15037=VECTOR('',#15036,5.863925654006E-1); -#15038=CARTESIAN_POINT('',(-2.917523870145E0,1.54E0,8.815613659747E0)); -#15039=LINE('',#15038,#15037); -#15040=CARTESIAN_POINT('',(-2.571600270028E0,1.54E0,8.940553874213E0)); -#15041=CARTESIAN_POINT('',(-2.686908136734E0,1.54E0,8.898907136057E0)); -#15042=CARTESIAN_POINT('',(-2.802216003439E0,1.54E0,8.857260397902E0)); -#15043=CARTESIAN_POINT('',(-2.917523870145E0,1.54E0,8.815613659747E0)); -#15045=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15046=VECTOR('',#15045,5.877696361310E-1); -#15047=CARTESIAN_POINT('',(-2.571600270028E0,1.54E0,9.528323510344E0)); -#15048=LINE('',#15047,#15046); -#15049=CARTESIAN_POINT('',(-1.923192564412E0,1.54E0,9.766460095156E0)); -#15050=CARTESIAN_POINT('',(-2.139328466284E0,1.54E0,9.687081233552E0)); -#15051=CARTESIAN_POINT('',(-2.355464368156E0,1.54E0,9.607702371948E0)); -#15052=CARTESIAN_POINT('',(-2.571600270028E0,1.54E0,9.528323510344E0)); -#15054=CARTESIAN_POINT('',(-1.583651130512E0,1.54E0,2.746647257959E-1)); -#15055=CARTESIAN_POINT('',(-1.620212713253E0,1.54E0,2.575906108458E-1)); -#15056=CARTESIAN_POINT('',(-1.693965805827E0,1.54E0,2.257354205418E-1)); -#15057=CARTESIAN_POINT('',(-1.807475495311E0,1.54E0,1.846964118506E-1)); -#15058=CARTESIAN_POINT('',(-1.884547613063E0,1.54E0,1.620213048244E-1)); -#15059=CARTESIAN_POINT('',(-1.923574730054E0,1.54E0,1.517666047689E-1)); -#15061=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15062=VECTOR('',#15061,1.015697209424E1); -#15063=CARTESIAN_POINT('',(-1.583651130512E0,1.54E0,1.043163682004E1)); -#15064=LINE('',#15063,#15062); -#15065=CARTESIAN_POINT('',(-1.795294462950E0,1.54E0,1.040130165008E1)); -#15066=CARTESIAN_POINT('',(-1.724746685471E0,1.54E0,1.041141337340E1)); -#15067=CARTESIAN_POINT('',(-1.654198907992E0,1.54E0,1.042152509672E1)); -#15068=CARTESIAN_POINT('',(-1.583651130512E0,1.54E0,1.043163682004E1)); -#15070=DIRECTION('',(0.E0,0.E0,1.E0)); -#15071=VECTOR('',#15070,6.425621784628E0); -#15072=CARTESIAN_POINT('',(-1.795294462950E0,1.54E0,3.975679865447E0)); -#15073=LINE('',#15072,#15071); -#15074=CARTESIAN_POINT('',(-2.410366337802E0,1.54E0,4.079032389891E0)); -#15075=CARTESIAN_POINT('',(-2.340114457097E0,1.54E0,4.078120253680E0)); -#15076=CARTESIAN_POINT('',(-2.201678909058E0,1.54E0,4.069780563810E0)); -#15077=CARTESIAN_POINT('',(-1.995544695180E0,1.54E0,4.035143162476E0)); -#15078=CARTESIAN_POINT('',(-1.861986253924E0,1.54E0,3.997778819083E0)); -#15079=CARTESIAN_POINT('',(-1.795294462950E0,1.54E0,3.975679865447E0)); -#15081=CARTESIAN_POINT('',(-2.391205348235E0,1.54E0,5.564484187773E0)); -#15082=CARTESIAN_POINT('',(-2.354357830985E0,1.54E0,5.576340476556E0)); -#15083=CARTESIAN_POINT('',(-2.288186642157E0,1.54E0,5.595380433702E0)); -#15084=CARTESIAN_POINT('',(-2.195357407806E0,1.54E0,5.616171505428E0)); -#15085=CARTESIAN_POINT('',(-2.111831957201E0,1.54E0,5.615418602152E0)); -#15086=CARTESIAN_POINT('',(-2.034076197603E0,1.54E0,5.584015125337E0)); -#15087=CARTESIAN_POINT('',(-1.972781047368E0,1.54E0,5.522551309388E0)); -#15088=CARTESIAN_POINT('',(-1.928054092846E0,1.54E0,5.439259103573E0)); -#15089=CARTESIAN_POINT('',(-1.899213171976E0,1.54E0,5.342449947031E0)); -#15090=CARTESIAN_POINT('',(-1.881113379202E0,1.54E0,5.230631831318E0)); -#15091=CARTESIAN_POINT('',(-1.872089472513E0,1.54E0,5.108584671973E0)); -#15092=CARTESIAN_POINT('',(-1.870102284188E0,1.54E0,4.971852350578E0)); -#15093=CARTESIAN_POINT('',(-1.877519906028E0,1.54E0,4.821002474585E0)); -#15094=CARTESIAN_POINT('',(-1.904720895203E0,1.54E0,4.652729311598E0)); -#15095=CARTESIAN_POINT('',(-1.965755743454E0,1.54E0,4.476901127391E0)); -#15096=CARTESIAN_POINT('',(-2.068548958876E0,1.54E0,4.310937031155E0)); -#15097=CARTESIAN_POINT('',(-2.217764594764E0,1.54E0,4.168967262148E0)); -#15098=CARTESIAN_POINT('',(-2.342435255587E0,1.54E0,4.106354389812E0)); -#15099=CARTESIAN_POINT('',(-2.410366337802E0,1.54E0,4.079032389891E0)); -#15101=DIRECTION('',(0.E0,0.E0,1.E0)); -#15102=VECTOR('',#15101,6.033030721040E-1); -#15103=CARTESIAN_POINT('',(-2.391205348235E0,1.54E0,4.961181115669E0)); -#15104=LINE('',#15103,#15102); -#15105=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.846769945275E0)); -#15106=CARTESIAN_POINT('',(-3.196821703419E0,1.54E0,3.836507874776E0)); -#15107=CARTESIAN_POINT('',(-3.267617117925E0,1.54E0,3.822281418096E0)); -#15108=CARTESIAN_POINT('',(-3.370278241467E0,1.54E0,3.826282414398E0)); -#15109=CARTESIAN_POINT('',(-3.453260400186E0,1.54E0,3.867724004155E0)); -#15110=CARTESIAN_POINT('',(-3.511026376279E0,1.54E0,3.940034077793E0)); -#15111=CARTESIAN_POINT('',(-3.550364059428E0,1.54E0,4.029588719334E0)); -#15112=CARTESIAN_POINT('',(-3.577434871114E0,1.54E0,4.137522770088E0)); -#15113=CARTESIAN_POINT('',(-3.592297876928E0,1.54E0,4.257412996233E0)); -#15114=CARTESIAN_POINT('',(-3.597137623280E0,1.54E0,4.394677155528E0)); -#15115=CARTESIAN_POINT('',(-3.591459875117E0,1.54E0,4.548170182436E0)); -#15116=CARTESIAN_POINT('',(-3.565880503959E0,1.54E0,4.725559501087E0)); -#15117=CARTESIAN_POINT('',(-3.504733918915E0,1.54E0,4.906399271463E0)); -#15118=CARTESIAN_POINT('',(-3.404203980925E0,1.54E0,5.067285385785E0)); -#15119=CARTESIAN_POINT('',(-3.277927727304E0,1.54E0,5.184843953642E0)); -#15120=CARTESIAN_POINT('',(-3.146454375608E0,1.54E0,5.266292111941E0)); -#15121=CARTESIAN_POINT('',(-3.021323460579E0,1.54E0,5.318959135186E0)); -#15122=CARTESIAN_POINT('',(-2.902969091898E0,1.54E0,5.346238958632E0)); -#15123=CARTESIAN_POINT('',(-2.793470908436E0,1.54E0,5.335332773683E0)); -#15124=CARTESIAN_POINT('',(-2.706455277582E0,1.54E0,5.280752382903E0)); -#15125=CARTESIAN_POINT('',(-2.647376471162E0,1.54E0,5.200835725455E0)); -#15126=CARTESIAN_POINT('',(-2.606034861335E0,1.54E0,5.109276993079E0)); -#15127=CARTESIAN_POINT('',(-2.577408899502E0,1.54E0,5.016216268724E0)); -#15128=CARTESIAN_POINT('',(-2.552947439405E0,1.54E0,4.928707344134E0)); -#15129=CARTESIAN_POINT('',(-2.528912753293E0,1.54E0,4.853786914811E0)); -#15130=CARTESIAN_POINT('',(-2.500086764451E0,1.54E0,4.789120278580E0)); -#15131=CARTESIAN_POINT('',(-2.463120703018E0,1.54E0,4.738216599066E0)); -#15132=CARTESIAN_POINT('',(-2.410785388690E0,1.54E0,4.708244416815E0)); -#15133=CARTESIAN_POINT('',(-2.352252012731E0,1.54E0,4.707222226833E0)); -#15134=CARTESIAN_POINT('',(-2.297253761183E0,1.54E0,4.727364871983E0)); -#15135=CARTESIAN_POINT('',(-2.249156763479E0,1.54E0,4.760285720910E0)); -#15136=CARTESIAN_POINT('',(-2.212441387626E0,1.54E0,4.800791762064E0)); -#15137=CARTESIAN_POINT('',(-2.188882518371E0,1.54E0,4.843663234200E0)); -#15138=CARTESIAN_POINT('',(-2.176387898204E0,1.54E0,4.885152520707E0)); -#15139=CARTESIAN_POINT('',(-2.174846630662E0,1.54E0,4.924165320916E0)); -#15140=CARTESIAN_POINT('',(-2.185509917337E0,1.54E0,4.957357257822E0)); -#15141=CARTESIAN_POINT('',(-2.207120652336E0,1.54E0,4.981741170427E0)); -#15142=CARTESIAN_POINT('',(-2.237930535033E0,1.54E0,4.992162334842E0)); -#15143=CARTESIAN_POINT('',(-2.272095552519E0,1.54E0,4.991007103051E0)); -#15144=CARTESIAN_POINT('',(-2.308504002543E0,1.54E0,4.982975727737E0)); -#15145=CARTESIAN_POINT('',(-2.348530748896E0,1.54E0,4.972754816942E0)); -#15146=CARTESIAN_POINT('',(-2.376416001770E0,1.54E0,4.965263453483E0)); -#15147=CARTESIAN_POINT('',(-2.391205348235E0,1.54E0,4.961181115669E0)); -#15149=DIRECTION('',(0.E0,0.E0,1.E0)); -#15150=VECTOR('',#15149,3.277524033064E-1); -#15151=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.519017541968E0)); -#15152=LINE('',#15151,#15150); -#15153=CARTESIAN_POINT('',(-1.923523774635E0,1.54E0,3.965343205076E0)); -#15154=CARTESIAN_POINT('',(-2.334742497799E0,1.54E0,3.816567984040E0)); -#15155=CARTESIAN_POINT('',(-2.745961220964E0,1.54E0,3.667792763004E0)); -#15156=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.519017541968E0)); -#15158=DIRECTION('',(0.E0,0.E0,1.E0)); -#15159=VECTOR('',#15158,6.113768855300E-1); -#15160=CARTESIAN_POINT('',(-1.923523774635E0,1.54E0,3.353966319546E0)); -#15161=LINE('',#15160,#15159); -#15162=CARTESIAN_POINT('',(-3.156772300777E0,1.54E0,2.906413167021E0)); -#15163=CARTESIAN_POINT('',(-2.745689458730E0,1.54E0,3.055597551196E0)); -#15164=CARTESIAN_POINT('',(-2.334606616682E0,1.54E0,3.204781935371E0)); -#15165=CARTESIAN_POINT('',(-1.923523774635E0,1.54E0,3.353966319546E0)); -#15167=DIRECTION('',(0.E0,0.E0,1.E0)); -#15168=VECTOR('',#15167,3.563665795030E-1); -#15169=CARTESIAN_POINT('',(-3.156772300777E0,1.54E0,2.550046587517E0)); -#15170=LINE('',#15169,#15168); -#15171=CARTESIAN_POINT('',(-3.544415650127E0,1.54E0,2.409368533274E0)); -#15172=CARTESIAN_POINT('',(-3.415201200344E0,1.54E0,2.456261218022E0)); -#15173=CARTESIAN_POINT('',(-3.285986750560E0,1.54E0,2.503153902770E0)); -#15174=CARTESIAN_POINT('',(-3.156772300777E0,1.54E0,2.550046587517E0)); -#15176=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15177=VECTOR('',#15176,1.329451658673E0); -#15178=CARTESIAN_POINT('',(-3.544415650127E0,1.54E0,3.738820191946E0)); -#15179=LINE('',#15178,#15177); -#15180=CARTESIAN_POINT('',(-3.544593994093E0,1.54E0,4.269990030724E-1)); -#15181=CARTESIAN_POINT('',(-3.669915187426E0,1.54E0,5.141501928736E-1)); -#15182=CARTESIAN_POINT('',(-3.899289232098E0,1.54E0,7.055000952881E-1)); -#15183=CARTESIAN_POINT('',(-4.161825236093E0,1.54E0,1.061164382636E0)); -#15184=CARTESIAN_POINT('',(-4.339964395968E0,1.54E0,1.453086385463E0)); -#15185=CARTESIAN_POINT('',(-4.429747574789E0,1.54E0,1.872154618193E0)); -#15186=CARTESIAN_POINT('',(-4.429103562739E0,1.54E0,2.299374203780E0)); -#15187=CARTESIAN_POINT('',(-4.338255535641E0,1.54E0,2.717599764232E0)); -#15188=CARTESIAN_POINT('',(-4.159649836747E0,1.54E0,3.108029094254E0)); -#15189=CARTESIAN_POINT('',(-3.897535141638E0,1.54E0,3.461802933253E0)); -#15190=CARTESIAN_POINT('',(-3.669133359728E0,1.54E0,3.652168495713E0)); -#15191=CARTESIAN_POINT('',(-3.544415650127E0,1.54E0,3.738820191946E0)); -#15193=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15194=VECTOR('',#15193,4.910827627040E-1); -#15195=CARTESIAN_POINT('',(-3.544593994093E0,1.54E0,9.180817657764E-1)); -#15196=LINE('',#15195,#15194); -#15197=CARTESIAN_POINT('',(-1.923574730054E0,1.54E0,1.507661440262E0)); -#15198=CARTESIAN_POINT('',(-2.463914484733E0,1.54E0,1.311134882100E0)); -#15199=CARTESIAN_POINT('',(-3.004254239413E0,1.54E0,1.114608323938E0)); -#15200=CARTESIAN_POINT('',(-3.544593994093E0,1.54E0,9.180817657764E-1)); -#15202=DIRECTION('',(0.E0,0.E0,1.E0)); -#15203=VECTOR('',#15202,1.355894835493E0); -#15204=CARTESIAN_POINT('',(-1.923574730054E0,1.54E0,1.517666047689E-1)); -#15205=LINE('',#15204,#15203); -#15206=DIRECTION('',(0.E0,0.E0,1.E0)); -#15207=VECTOR('',#15206,5.948581024751E-1); -#15208=CARTESIAN_POINT('',(-2.571396448352E0,1.54E0,1.452272899908E0)); -#15209=LINE('',#15208,#15207); -#15210=CARTESIAN_POINT('',(-2.917332787324E0,1.54E0,1.330285627040E0)); -#15211=CARTESIAN_POINT('',(-2.802020674334E0,1.54E0,1.370948051329E0)); -#15212=CARTESIAN_POINT('',(-2.686708561343E0,1.54E0,1.411610475618E0)); -#15213=CARTESIAN_POINT('',(-2.571396448352E0,1.54E0,1.452272899908E0)); -#15215=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15216=VECTOR('',#15215,5.881607088224E-1); -#15217=CARTESIAN_POINT('',(-2.917332787324E0,1.54E0,1.918446335862E0)); -#15218=LINE('',#15217,#15216); -#15219=CARTESIAN_POINT('',(-3.156810517342E0,1.54E0,1.833558752992E0)); -#15220=CARTESIAN_POINT('',(-3.076984607336E0,1.54E0,1.861854613949E0)); -#15221=CARTESIAN_POINT('',(-2.997158697330E0,1.54E0,1.890150474905E0)); -#15222=CARTESIAN_POINT('',(-2.917332787324E0,1.54E0,1.918446335862E0)); -#15224=DIRECTION('',(0.E0,0.E0,1.E0)); -#15225=VECTOR('',#15224,6.464951434009E-1); -#15226=CARTESIAN_POINT('',(-3.156810517342E0,1.54E0,1.187063609591E0)); -#15227=LINE('',#15226,#15225); -#15228=CARTESIAN_POINT('',(-3.543880618228E0,1.54E0,1.048658884147E0)); -#15229=CARTESIAN_POINT('',(-3.414857251266E0,1.54E0,1.094793792628E0)); -#15230=CARTESIAN_POINT('',(-3.285833884304E0,1.54E0,1.140928701110E0)); -#15231=CARTESIAN_POINT('',(-3.156810517342E0,1.54E0,1.187063609591E0)); -#15233=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15234=VECTOR('',#15233,1.255996263269E0); -#15235=CARTESIAN_POINT('',(-3.543880618228E0,1.54E0,2.304655147416E0)); -#15236=LINE('',#15235,#15234); -#15237=CARTESIAN_POINT('',(-1.923625685473E0,1.54E0,2.892655203915E0)); -#15238=CARTESIAN_POINT('',(-2.463710663058E0,1.54E0,2.696655185082E0)); -#15239=CARTESIAN_POINT('',(-3.003795640643E0,1.54E0,2.500655166249E0)); -#15240=CARTESIAN_POINT('',(-3.543880618228E0,1.54E0,2.304655147416E0)); -#15242=DIRECTION('',(0.E0,0.E0,1.E0)); -#15243=VECTOR('',#15242,1.256509610971E0); -#15244=CARTESIAN_POINT('',(-1.923625685473E0,1.54E0,1.636145592944E0)); -#15245=LINE('',#15244,#15243); -#15246=CARTESIAN_POINT('',(-2.310530181248E0,1.54E0,1.497800082950E0)); -#15247=CARTESIAN_POINT('',(-2.181562015989E0,1.54E0,1.543915252948E0)); -#15248=CARTESIAN_POINT('',(-2.052593850731E0,1.54E0,1.590030422946E0)); -#15249=CARTESIAN_POINT('',(-1.923625685473E0,1.54E0,1.636145592944E0)); -#15251=DIRECTION('',(0.E0,0.E0,-1.E0)); -#15252=VECTOR('',#15251,6.414537746874E-1); -#15253=CARTESIAN_POINT('',(-2.310530181248E0,1.54E0,2.139253857638E0)); -#15254=LINE('',#15253,#15252); -#15255=CARTESIAN_POINT('',(-2.571396448352E0,1.54E0,2.047131002383E0)); -#15256=CARTESIAN_POINT('',(-2.484441025984E0,1.54E0,2.077838620801E0)); -#15257=CARTESIAN_POINT('',(-2.397485603616E0,1.54E0,2.108546239219E0)); -#15258=CARTESIAN_POINT('',(-2.310530181248E0,1.54E0,2.139253857638E0)); -#15260=DIRECTION('',(-2.220446049250E-14,-1.E0,0.E0)); -#15261=VECTOR('',#15260,1.E-2); -#15262=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.765777389509E0)); -#15263=LINE('',#15262,#15261); -#15264=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15265=VECTOR('',#15264,1.E-2); -#15266=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.999217256483E-1)); -#15267=LINE('',#15266,#15265); -#15268=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15269=VECTOR('',#15268,1.E-2); -#15270=CARTESIAN_POINT('',(-2.705883122562E0,1.55E0,4.059909751877E0)); -#15271=LINE('',#15270,#15269); -#15272=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15273=VECTOR('',#15272,1.E-2); -#15274=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.941801323147E0)); -#15275=LINE('',#15274,#15273); -#15276=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15277=VECTOR('',#15276,1.E-2); -#15278=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,4.412619339018E0)); -#15279=LINE('',#15278,#15277); -#15280=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15281=VECTOR('',#15280,1.E-2); -#15282=CARTESIAN_POINT('',(-2.575625748121E0,1.55E0,6.119789271963E0)); -#15283=LINE('',#15282,#15281); -#15284=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15285=VECTOR('',#15284,1.E-2); -#15286=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.756586997800E0)); -#15287=LINE('',#15286,#15285); -#15288=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15289=VECTOR('',#15288,1.E-2); -#15290=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.239527664520E0)); -#15291=LINE('',#15290,#15289); -#15292=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15293=VECTOR('',#15292,1.E-2); -#15294=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,5.825383145660E0)); -#15295=LINE('',#15294,#15293); -#15296=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15297=VECTOR('',#15296,1.E-2); -#15298=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,6.615024988339E0)); -#15299=LINE('',#15298,#15297); -#15300=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15301=VECTOR('',#15300,1.E-2); -#15302=CARTESIAN_POINT('',(-2.874810490240E0,1.55E0,6.616961294258E0)); -#15303=LINE('',#15302,#15301); -#15304=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15305=VECTOR('',#15304,1.E-2); -#15306=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,6.967587730580E0)); -#15307=LINE('',#15306,#15305); -#15308=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15309=VECTOR('',#15308,1.E-2); -#15310=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,7.489725709329E0)); -#15311=LINE('',#15310,#15309); -#15312=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15313=VECTOR('',#15312,1.E-2); -#15314=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.898362595182E0)); -#15315=LINE('',#15314,#15313); -#15316=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15317=VECTOR('',#15316,1.E-2); -#15318=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.111585449519E0)); -#15319=LINE('',#15318,#15317); -#15320=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15321=VECTOR('',#15320,1.E-2); -#15322=CARTESIAN_POINT('',(-3.239727722762E0,1.55E0,7.911611100185E0)); -#15323=LINE('',#15322,#15321); -#15324=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15325=VECTOR('',#15324,1.E-2); -#15326=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.312648204863E0)); -#15327=LINE('',#15326,#15325); -#15328=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15329=VECTOR('',#15328,1.E-2); -#15330=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.067463319291E0)); -#15331=LINE('',#15330,#15329); -#15332=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-13)); -#15333=VECTOR('',#15332,1.E-2); -#15334=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,9.242286387282E0)); -#15335=LINE('',#15334,#15333); -#15336=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15337=VECTOR('',#15336,1.E-2); -#15338=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,8.226771904890E0)); -#15339=LINE('',#15338,#15337); -#15340=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15341=VECTOR('',#15340,1.E-2); -#15342=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,7.391589548398E0)); -#15343=LINE('',#15342,#15341); -#15344=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15345=VECTOR('',#15344,1.E-2); -#15346=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,7.560244033212E0)); -#15347=LINE('',#15346,#15345); -#15348=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15349=VECTOR('',#15348,1.E-2); -#15350=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,8.187006604870E0)); -#15351=LINE('',#15350,#15349); -#15352=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15353=VECTOR('',#15352,1.E-2); -#15354=CARTESIAN_POINT('',(-2.175065200079E0,1.55E0,8.141267173208E0)); -#15355=LINE('',#15354,#15353); -#15356=DIRECTION('',(4.440892098501E-14,-1.E0,0.E0)); -#15357=VECTOR('',#15356,1.E-2); -#15358=CARTESIAN_POINT('',(-2.177281760801E0,1.55E0,8.477445549459E0)); -#15359=LINE('',#15358,#15357); -#15360=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15361=VECTOR('',#15360,1.E-2); -#15362=CARTESIAN_POINT('',(-1.924237150499E0,1.55E0,8.612299065602E0)); -#15363=LINE('',#15362,#15361); -#15364=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15365=VECTOR('',#15364,1.E-2); -#15366=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,1.037838840728E1)); -#15367=LINE('',#15366,#15365); -#15368=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15369=VECTOR('',#15368,1.E-2); -#15370=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,9.792991750417E0)); -#15371=LINE('',#15370,#15369); -#15372=DIRECTION('',(4.440892098501E-14,-1.E0,0.E0)); -#15373=VECTOR('',#15372,1.E-2); -#15374=CARTESIAN_POINT('',(-3.543727751972E0,1.55E0,8.534948739698E0)); -#15375=LINE('',#15374,#15373); -#15376=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15377=VECTOR('',#15376,1.E-2); -#15378=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,8.677888105413E0)); -#15379=LINE('',#15378,#15377); -#15380=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15381=VECTOR('',#15380,1.E-2); -#15382=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,9.305944961207E0)); -#15383=LINE('',#15382,#15381); -#15384=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-13)); -#15385=VECTOR('',#15384,1.E-2); -#15386=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,9.402006225147E0)); -#15387=LINE('',#15386,#15385); -#15388=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15389=VECTOR('',#15388,1.E-2); -#15390=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,8.815613659747E0)); -#15391=LINE('',#15390,#15389); -#15392=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15393=VECTOR('',#15392,1.E-2); -#15394=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,8.940553874213E0)); -#15395=LINE('',#15394,#15393); -#15396=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-13)); -#15397=VECTOR('',#15396,1.E-2); -#15398=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,9.528323510344E0)); -#15399=LINE('',#15398,#15397); -#15400=DIRECTION('',(2.220446049250E-14,-1.E0,1.776356839400E-13)); -#15401=VECTOR('',#15400,1.E-2); -#15402=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,9.766460095156E0)); -#15403=LINE('',#15402,#15401); -#15404=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15405=VECTOR('',#15404,1.E-2); -#15406=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,2.746647257959E-1)); -#15407=LINE('',#15406,#15405); -#15408=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-13)); -#15409=VECTOR('',#15408,1.E-2); -#15410=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,1.043163682004E1)); -#15411=LINE('',#15410,#15409); -#15412=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15413=VECTOR('',#15412,1.E-2); -#15414=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,1.040130165008E1)); -#15415=LINE('',#15414,#15413); -#15416=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15417=VECTOR('',#15416,1.E-2); -#15418=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,3.975679865447E0)); -#15419=LINE('',#15418,#15417); -#15420=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15421=VECTOR('',#15420,1.E-2); -#15422=CARTESIAN_POINT('',(-2.410366337802E0,1.55E0,4.079032389891E0)); -#15423=LINE('',#15422,#15421); -#15424=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15425=VECTOR('',#15424,1.E-2); -#15426=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,5.564484187773E0)); -#15427=LINE('',#15426,#15425); -#15428=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15429=VECTOR('',#15428,1.E-2); -#15430=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,4.961181115669E0)); -#15431=LINE('',#15430,#15429); -#15432=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15433=VECTOR('',#15432,1.E-2); -#15434=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.846769945275E0)); -#15435=LINE('',#15434,#15433); -#15436=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15437=VECTOR('',#15436,1.E-2); -#15438=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.519017541968E0)); -#15439=LINE('',#15438,#15437); -#15440=DIRECTION('',(0.E0,-1.E0,-4.440892098501E-14)); -#15441=VECTOR('',#15440,1.E-2); -#15442=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.965343205076E0)); -#15443=LINE('',#15442,#15441); -#15444=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15445=VECTOR('',#15444,1.E-2); -#15446=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.353966319546E0)); -#15447=LINE('',#15446,#15445); -#15448=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15449=VECTOR('',#15448,1.E-2); -#15450=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.906413167021E0)); -#15451=LINE('',#15450,#15449); -#15452=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15453=VECTOR('',#15452,1.E-2); -#15454=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.550046587517E0)); -#15455=LINE('',#15454,#15453); -#15456=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15457=VECTOR('',#15456,1.E-2); -#15458=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,2.409368533274E0)); -#15459=LINE('',#15458,#15457); -#15460=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15461=VECTOR('',#15460,1.E-2); -#15462=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,3.738820191946E0)); -#15463=LINE('',#15462,#15461); -#15464=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15465=VECTOR('',#15464,1.E-2); -#15466=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,4.269990030724E-1)); -#15467=LINE('',#15466,#15465); -#15468=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15469=VECTOR('',#15468,1.E-2); -#15470=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,9.180817657764E-1)); -#15471=LINE('',#15470,#15469); -#15472=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15473=VECTOR('',#15472,1.E-2); -#15474=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.507661440262E0)); -#15475=LINE('',#15474,#15473); -#15476=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15477=VECTOR('',#15476,1.E-2); -#15478=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.517666047689E-1)); -#15479=LINE('',#15478,#15477); -#15480=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15481=VECTOR('',#15480,1.E-2); -#15482=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,1.452272899908E0)); -#15483=LINE('',#15482,#15481); -#15484=DIRECTION('',(8.881784197001E-14,-1.E0,0.E0)); -#15485=VECTOR('',#15484,1.E-2); -#15486=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.330285627040E0)); -#15487=LINE('',#15486,#15485); -#15488=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15489=VECTOR('',#15488,1.E-2); -#15490=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.918446335862E0)); -#15491=LINE('',#15490,#15489); -#15492=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15493=VECTOR('',#15492,1.E-2); -#15494=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.833558752992E0)); -#15495=LINE('',#15494,#15493); -#15496=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15497=VECTOR('',#15496,1.E-2); -#15498=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.187063609591E0)); -#15499=LINE('',#15498,#15497); -#15500=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15501=VECTOR('',#15500,1.E-2); -#15502=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,1.048658884147E0)); -#15503=LINE('',#15502,#15501); -#15504=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15505=VECTOR('',#15504,1.E-2); -#15506=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,2.304655147416E0)); -#15507=LINE('',#15506,#15505); -#15508=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15509=VECTOR('',#15508,1.E-2); -#15510=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,2.892655203915E0)); -#15511=LINE('',#15510,#15509); -#15512=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15513=VECTOR('',#15512,1.E-2); -#15514=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,1.636145592944E0)); -#15515=LINE('',#15514,#15513); -#15516=DIRECTION('',(0.E0,-1.E0,-4.440892098501E-14)); -#15517=VECTOR('',#15516,1.E-2); -#15518=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,1.497800082950E0)); -#15519=LINE('',#15518,#15517); -#15520=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15521=VECTOR('',#15520,1.E-2); -#15522=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,2.139253857638E0)); -#15523=LINE('',#15522,#15521); -#15524=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15525=VECTOR('',#15524,1.E-2); -#15526=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,2.047131002383E0)); -#15527=LINE('',#15526,#15525); -#15528=DIRECTION('',(0.E0,1.E0,0.E0)); -#15529=VECTOR('',#15528,1.1E0); -#15530=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.83E0)); -#15531=LINE('',#15530,#15529); -#15532=DIRECTION('',(0.E0,1.E0,0.E0)); -#15533=VECTOR('',#15532,1.1E0); -#15534=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.83E0)); -#15535=LINE('',#15534,#15533); -#15536=DIRECTION('',(0.E0,1.E0,0.E0)); -#15537=VECTOR('',#15536,1.1E0); -#15538=CARTESIAN_POINT('',(-5.25E0,3.E-1,6.861069017863E0)); -#15539=LINE('',#15538,#15537); -#15540=DIRECTION('',(0.E0,1.E0,0.E0)); -#15541=VECTOR('',#15540,1.1E0); -#15542=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.628565170500E-1)); -#15543=LINE('',#15542,#15541); -#15544=DIRECTION('',(0.E0,1.E0,0.E0)); -#15545=VECTOR('',#15544,1.1E0); -#15546=CARTESIAN_POINT('',(6.65E0,3.E-1,5.639068448582E0)); -#15547=LINE('',#15546,#15545); -#15548=DIRECTION('',(0.E0,1.E0,0.E0)); -#15549=VECTOR('',#15548,1.1E0); -#15550=CARTESIAN_POINT('',(6.65E0,3.E-1,9.156381348264E-1)); -#15551=LINE('',#15550,#15549); -#15552=DIRECTION('',(0.E0,1.E0,0.E0)); -#15553=VECTOR('',#15552,1.1E0); -#15554=CARTESIAN_POINT('',(6.65E0,3.E-1,-8.436186517363E-2)); -#15555=LINE('',#15554,#15553); -#15556=DIRECTION('',(0.E0,1.E0,0.E0)); -#15557=VECTOR('',#15556,1.1E0); -#15558=CARTESIAN_POINT('',(6.65E0,3.E-1,-1.58E0)); -#15559=LINE('',#15558,#15557); -#15560=CARTESIAN_POINT('',(-7.55E0,-2.5E-1,-1.3735E1)); -#15561=DIRECTION('',(0.E0,1.E0,0.E0)); -#15562=DIRECTION('',(2.E-1,0.E0,9.797958971133E-1)); -#15563=AXIS2_PLACEMENT_3D('',#15560,#15561,#15562); -#15565=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.3735E1)); -#15566=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15567=DIRECTION('',(2.E-1,0.E0,-9.797958971133E-1)); -#15568=AXIS2_PLACEMENT_3D('',#15565,#15566,#15567); -#15570=DIRECTION('',(0.E0,1.E0,0.E0)); -#15571=VECTOR('',#15570,6.E-1); -#15572=CARTESIAN_POINT('',(7.5E0,-3.E-1,-1.43E1)); -#15573=LINE('',#15572,#15571); -#15574=DIRECTION('',(0.E0,1.E0,0.E0)); -#15575=VECTOR('',#15574,5.E-2); -#15576=CARTESIAN_POINT('',(7.5E0,2.5E-1,4.55E0)); -#15577=LINE('',#15576,#15575); -#15578=DIRECTION('',(0.E0,1.E0,0.E0)); -#15579=VECTOR('',#15578,5.E-2); -#15580=CARTESIAN_POINT('',(7.5E0,-3.E-1,4.55E0)); -#15581=LINE('',#15580,#15579); -#15582=DIRECTION('',(0.E0,1.E0,0.E0)); -#15583=VECTOR('',#15582,5.E-1); -#15584=CARTESIAN_POINT('',(7.5E0,-2.5E-1,4.55E0)); -#15585=LINE('',#15584,#15583); -#15586=DIRECTION('',(0.E0,1.E0,-1.776356839400E-14)); -#15587=VECTOR('',#15586,5.E-2); -#15588=CARTESIAN_POINT('',(7.5E0,2.5E-1,5.65E0)); -#15589=LINE('',#15588,#15587); -#15590=DIRECTION('',(0.E0,1.E0,0.E0)); -#15591=VECTOR('',#15590,5.E-2); -#15592=CARTESIAN_POINT('',(7.5E0,2.5E-1,5.25E0)); -#15593=LINE('',#15592,#15591); -#15594=DIRECTION('',(0.E0,1.E0,0.E0)); -#15595=VECTOR('',#15594,5.E-1); -#15596=CARTESIAN_POINT('',(7.5E0,-2.5E-1,5.25E0)); -#15597=LINE('',#15596,#15595); -#15598=DIRECTION('',(0.E0,1.E0,0.E0)); -#15599=VECTOR('',#15598,5.E-2); -#15600=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.25E0)); -#15601=LINE('',#15600,#15599); -#15602=DIRECTION('',(0.E0,1.E0,1.776356839400E-14)); -#15603=VECTOR('',#15602,5.E-2); -#15604=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.65E0)); -#15605=LINE('',#15604,#15603); -#15606=DIRECTION('',(0.E0,1.E0,0.E0)); -#15607=VECTOR('',#15606,5.E-1); -#15608=CARTESIAN_POINT('',(7.5E0,-2.5E-1,5.65E0)); -#15609=LINE('',#15608,#15607); -#15610=DIRECTION('',(0.E0,1.E0,0.E0)); -#15611=VECTOR('',#15610,5.E-2); -#15612=CARTESIAN_POINT('',(7.5E0,2.5E-1,6.75E0)); -#15613=LINE('',#15612,#15611); -#15614=DIRECTION('',(0.E0,1.E0,1.776356839400E-14)); -#15615=VECTOR('',#15614,5.E-2); -#15616=CARTESIAN_POINT('',(7.5E0,2.5E-1,6.35E0)); -#15617=LINE('',#15616,#15615); -#15618=DIRECTION('',(0.E0,1.E0,0.E0)); -#15619=VECTOR('',#15618,5.E-1); -#15620=CARTESIAN_POINT('',(7.5E0,-2.5E-1,6.35E0)); -#15621=LINE('',#15620,#15619); -#15622=DIRECTION('',(0.E0,1.E0,-3.552713678801E-14)); -#15623=VECTOR('',#15622,5.E-2); -#15624=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.35E0)); -#15625=LINE('',#15624,#15623); -#15626=DIRECTION('',(0.E0,1.E0,0.E0)); -#15627=VECTOR('',#15626,5.E-2); -#15628=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.75E0)); -#15629=LINE('',#15628,#15627); -#15630=DIRECTION('',(0.E0,1.E0,0.E0)); -#15631=VECTOR('',#15630,5.E-1); -#15632=CARTESIAN_POINT('',(7.5E0,-2.5E-1,6.75E0)); -#15633=LINE('',#15632,#15631); -#15634=DIRECTION('',(0.E0,1.E0,-1.776356839400E-14)); -#15635=VECTOR('',#15634,5.E-2); -#15636=CARTESIAN_POINT('',(7.5E0,2.5E-1,7.85E0)); -#15637=LINE('',#15636,#15635); -#15638=DIRECTION('',(0.E0,1.E0,1.776356839400E-14)); -#15639=VECTOR('',#15638,5.E-2); -#15640=CARTESIAN_POINT('',(7.5E0,2.5E-1,7.45E0)); -#15641=LINE('',#15640,#15639); -#15642=DIRECTION('',(0.E0,1.E0,0.E0)); -#15643=VECTOR('',#15642,5.E-1); -#15644=CARTESIAN_POINT('',(7.5E0,-2.5E-1,7.45E0)); -#15645=LINE('',#15644,#15643); -#15646=DIRECTION('',(0.E0,1.E0,-3.552713678801E-14)); -#15647=VECTOR('',#15646,5.E-2); -#15648=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.45E0)); -#15649=LINE('',#15648,#15647); -#15650=DIRECTION('',(0.E0,1.E0,1.776356839400E-14)); -#15651=VECTOR('',#15650,5.E-2); -#15652=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.85E0)); -#15653=LINE('',#15652,#15651); -#15654=DIRECTION('',(0.E0,1.E0,0.E0)); -#15655=VECTOR('',#15654,5.E-1); -#15656=CARTESIAN_POINT('',(7.5E0,-2.5E-1,7.85E0)); -#15657=LINE('',#15656,#15655); -#15658=DIRECTION('',(0.E0,1.E0,0.E0)); -#15659=VECTOR('',#15658,5.E-2); -#15660=CARTESIAN_POINT('',(7.5E0,2.5E-1,8.95E0)); -#15661=LINE('',#15660,#15659); -#15662=DIRECTION('',(0.E0,1.E0,0.E0)); -#15663=VECTOR('',#15662,5.E-2); -#15664=CARTESIAN_POINT('',(7.5E0,2.5E-1,8.55E0)); -#15665=LINE('',#15664,#15663); -#15666=DIRECTION('',(0.E0,1.E0,0.E0)); -#15667=VECTOR('',#15666,5.E-1); -#15668=CARTESIAN_POINT('',(7.5E0,-2.5E-1,8.55E0)); -#15669=LINE('',#15668,#15667); -#15670=DIRECTION('',(0.E0,1.E0,0.E0)); -#15671=VECTOR('',#15670,5.E-2); -#15672=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.55E0)); -#15673=LINE('',#15672,#15671); -#15674=DIRECTION('',(0.E0,1.E0,-3.552713678801E-14)); -#15675=VECTOR('',#15674,5.E-2); -#15676=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.95E0)); -#15677=LINE('',#15676,#15675); -#15678=DIRECTION('',(0.E0,1.E0,0.E0)); -#15679=VECTOR('',#15678,5.E-1); -#15680=CARTESIAN_POINT('',(7.5E0,-2.5E-1,8.95E0)); -#15681=LINE('',#15680,#15679); -#15682=DIRECTION('',(0.E0,1.E0,7.105427357601E-14)); -#15683=VECTOR('',#15682,5.E-2); -#15684=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.005E1)); -#15685=LINE('',#15684,#15683); -#15686=DIRECTION('',(0.E0,1.E0,-7.105427357601E-14)); -#15687=VECTOR('',#15686,5.E-2); -#15688=CARTESIAN_POINT('',(7.5E0,2.5E-1,9.65E0)); -#15689=LINE('',#15688,#15687); -#15690=DIRECTION('',(0.E0,1.E0,0.E0)); -#15691=VECTOR('',#15690,5.E-1); -#15692=CARTESIAN_POINT('',(7.5E0,-2.5E-1,9.65E0)); -#15693=LINE('',#15692,#15691); -#15694=DIRECTION('',(0.E0,1.E0,3.552713678801E-14)); -#15695=VECTOR('',#15694,5.E-2); -#15696=CARTESIAN_POINT('',(7.5E0,-3.E-1,9.65E0)); -#15697=LINE('',#15696,#15695); -#15698=DIRECTION('',(0.E0,1.E0,-7.105427357601E-14)); -#15699=VECTOR('',#15698,5.E-2); -#15700=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.005E1)); -#15701=LINE('',#15700,#15699); -#15702=DIRECTION('',(0.E0,1.E0,0.E0)); -#15703=VECTOR('',#15702,5.E-1); -#15704=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.005E1)); -#15705=LINE('',#15704,#15703); -#15706=DIRECTION('',(0.E0,1.E0,0.E0)); -#15707=VECTOR('',#15706,5.E-2); -#15708=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.115E1)); -#15709=LINE('',#15708,#15707); -#15710=DIRECTION('',(0.E0,1.E0,-3.552713678801E-14)); -#15711=VECTOR('',#15710,5.E-2); -#15712=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.075E1)); -#15713=LINE('',#15712,#15711); -#15714=DIRECTION('',(0.E0,1.E0,0.E0)); -#15715=VECTOR('',#15714,5.E-1); -#15716=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.075E1)); -#15717=LINE('',#15716,#15715); -#15718=DIRECTION('',(0.E0,1.E0,3.552713678801E-14)); -#15719=VECTOR('',#15718,5.E-2); -#15720=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.075E1)); -#15721=LINE('',#15720,#15719); -#15722=DIRECTION('',(0.E0,1.E0,0.E0)); -#15723=VECTOR('',#15722,5.E-2); -#15724=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.115E1)); -#15725=LINE('',#15724,#15723); -#15726=DIRECTION('',(0.E0,1.E0,0.E0)); -#15727=VECTOR('',#15726,5.E-1); -#15728=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.115E1)); -#15729=LINE('',#15728,#15727); -#15730=DIRECTION('',(0.E0,1.E0,0.E0)); -#15731=VECTOR('',#15730,5.E-2); -#15732=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.225E1)); -#15733=LINE('',#15732,#15731); -#15734=DIRECTION('',(0.E0,1.E0,0.E0)); -#15735=VECTOR('',#15734,5.E-2); -#15736=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.185E1)); -#15737=LINE('',#15736,#15735); -#15738=DIRECTION('',(0.E0,1.E0,0.E0)); -#15739=VECTOR('',#15738,5.E-1); -#15740=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.185E1)); -#15741=LINE('',#15740,#15739); -#15742=DIRECTION('',(0.E0,1.E0,0.E0)); -#15743=VECTOR('',#15742,5.E-2); -#15744=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.185E1)); -#15745=LINE('',#15744,#15743); -#15746=DIRECTION('',(0.E0,1.E0,3.552713678801E-14)); -#15747=VECTOR('',#15746,5.E-2); -#15748=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.225E1)); -#15749=LINE('',#15748,#15747); -#15750=DIRECTION('',(0.E0,1.E0,0.E0)); -#15751=VECTOR('',#15750,5.E-1); -#15752=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.225E1)); -#15753=LINE('',#15752,#15751); -#15754=DIRECTION('',(0.E0,1.E0,7.105427357601E-14)); -#15755=VECTOR('',#15754,5.E-2); -#15756=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.295E1)); -#15757=LINE('',#15756,#15755); -#15758=DIRECTION('',(0.E0,1.E0,0.E0)); -#15759=VECTOR('',#15758,6.E-1); -#15760=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#15761=LINE('',#15760,#15759); -#15762=DIRECTION('',(0.E0,1.E0,-3.552713678801E-14)); -#15763=VECTOR('',#15762,5.E-2); -#15764=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.295E1)); -#15765=LINE('',#15764,#15763); -#15766=DIRECTION('',(0.E0,1.E0,0.E0)); -#15767=VECTOR('',#15766,5.E-1); -#15768=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.295E1)); -#15769=LINE('',#15768,#15767); -#15770=DIRECTION('',(-1.E0,0.E0,0.E0)); -#15771=VECTOR('',#15770,6.E-1); -#15772=CARTESIAN_POINT('',(7.5E0,-2.5E-1,4.55E0)); -#15773=LINE('',#15772,#15771); -#15774=DIRECTION('',(-1.E0,0.E0,0.E0)); -#15775=VECTOR('',#15774,6.E-1); -#15776=CARTESIAN_POINT('',(7.5E0,2.5E-1,4.55E0)); -#15777=LINE('',#15776,#15775); -#15778=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,4.9E0)); -#15779=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15780=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#15781=AXIS2_PLACEMENT_3D('',#15778,#15779,#15780); -#15783=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,4.9E0)); -#15784=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15785=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#15786=AXIS2_PLACEMENT_3D('',#15783,#15784,#15785); -#15788=DIRECTION('',(1.E0,0.E0,0.E0)); -#15789=VECTOR('',#15788,6.E-1); -#15790=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,5.25E0)); -#15791=LINE('',#15790,#15789); -#15792=DIRECTION('',(1.E0,0.E0,0.E0)); -#15793=VECTOR('',#15792,6.E-1); -#15794=CARTESIAN_POINT('',(-6.5E0,2.5E-1,5.25E0)); -#15795=LINE('',#15794,#15793); -#15796=DIRECTION('',(-1.776356839400E-14,1.E0,1.776356839400E-14)); -#15797=VECTOR('',#15796,5.E-2); -#15798=CARTESIAN_POINT('',(-6.5E0,-3.E-1,4.55E0)); -#15799=LINE('',#15798,#15797); -#15800=DIRECTION('',(0.E0,1.E0,0.E0)); -#15801=VECTOR('',#15800,6.E-1); -#15802=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#15803=LINE('',#15802,#15801); -#15804=DIRECTION('',(1.776356839400E-14,1.E0,-1.776356839400E-14)); -#15805=VECTOR('',#15804,5.E-2); -#15806=CARTESIAN_POINT('',(-6.5E0,2.5E-1,4.55E0)); -#15807=LINE('',#15806,#15805); -#15808=DIRECTION('',(0.E0,1.E0,0.E0)); -#15809=VECTOR('',#15808,5.E-1); -#15810=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,4.55E0)); -#15811=LINE('',#15810,#15809); -#15812=DIRECTION('',(-1.776356839400E-14,1.E0,1.776356839400E-14)); -#15813=VECTOR('',#15812,5.E-2); -#15814=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.65E0)); -#15815=LINE('',#15814,#15813); -#15816=DIRECTION('',(-1.776356839400E-14,1.E0,-1.776356839400E-14)); -#15817=VECTOR('',#15816,5.E-2); -#15818=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.25E0)); -#15819=LINE('',#15818,#15817); -#15820=DIRECTION('',(0.E0,1.E0,0.E0)); -#15821=VECTOR('',#15820,5.E-1); -#15822=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,5.25E0)); -#15823=LINE('',#15822,#15821); -#15824=DIRECTION('',(1.776356839400E-14,1.E0,1.776356839400E-14)); -#15825=VECTOR('',#15824,5.E-2); -#15826=CARTESIAN_POINT('',(-6.5E0,2.5E-1,5.25E0)); -#15827=LINE('',#15826,#15825); -#15828=DIRECTION('',(1.776356839400E-14,1.E0,-1.776356839400E-14)); -#15829=VECTOR('',#15828,5.E-2); -#15830=CARTESIAN_POINT('',(-6.5E0,2.5E-1,5.65E0)); -#15831=LINE('',#15830,#15829); -#15832=DIRECTION('',(0.E0,1.E0,0.E0)); -#15833=VECTOR('',#15832,5.E-1); -#15834=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,5.65E0)); -#15835=LINE('',#15834,#15833); -#15836=DIRECTION('',(-1.776356839400E-14,1.E0,0.E0)); -#15837=VECTOR('',#15836,5.E-2); -#15838=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.75E0)); -#15839=LINE('',#15838,#15837); -#15840=DIRECTION('',(-3.552713678801E-14,1.E0,-1.776356839400E-14)); -#15841=VECTOR('',#15840,5.E-2); -#15842=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.35E0)); -#15843=LINE('',#15842,#15841); -#15844=DIRECTION('',(0.E0,1.E0,0.E0)); -#15845=VECTOR('',#15844,5.E-1); -#15846=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,6.35E0)); -#15847=LINE('',#15846,#15845); -#15848=DIRECTION('',(3.552713678801E-14,1.E0,3.552713678801E-14)); -#15849=VECTOR('',#15848,5.E-2); -#15850=CARTESIAN_POINT('',(-6.5E0,2.5E-1,6.35E0)); -#15851=LINE('',#15850,#15849); -#15852=DIRECTION('',(1.776356839400E-14,1.E0,0.E0)); -#15853=VECTOR('',#15852,5.E-2); -#15854=CARTESIAN_POINT('',(-6.5E0,2.5E-1,6.75E0)); -#15855=LINE('',#15854,#15853); -#15856=DIRECTION('',(0.E0,1.E0,0.E0)); -#15857=VECTOR('',#15856,5.E-1); -#15858=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,6.75E0)); -#15859=LINE('',#15858,#15857); -#15860=DIRECTION('',(-3.552713678801E-14,1.E0,1.776356839400E-14)); -#15861=VECTOR('',#15860,5.E-2); -#15862=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.85E0)); -#15863=LINE('',#15862,#15861); -#15864=DIRECTION('',(-1.776356839400E-14,1.E0,-1.776356839400E-14)); -#15865=VECTOR('',#15864,5.E-2); -#15866=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.45E0)); -#15867=LINE('',#15866,#15865); -#15868=DIRECTION('',(0.E0,1.E0,0.E0)); -#15869=VECTOR('',#15868,5.E-1); -#15870=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,7.45E0)); -#15871=LINE('',#15870,#15869); -#15872=DIRECTION('',(1.776356839400E-14,1.E0,3.552713678801E-14)); -#15873=VECTOR('',#15872,5.E-2); -#15874=CARTESIAN_POINT('',(-6.5E0,2.5E-1,7.45E0)); -#15875=LINE('',#15874,#15873); -#15876=DIRECTION('',(3.552713678801E-14,1.E0,-1.776356839400E-14)); -#15877=VECTOR('',#15876,5.E-2); -#15878=CARTESIAN_POINT('',(-6.5E0,2.5E-1,7.85E0)); -#15879=LINE('',#15878,#15877); -#15880=DIRECTION('',(0.E0,1.E0,0.E0)); -#15881=VECTOR('',#15880,5.E-1); -#15882=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,7.85E0)); -#15883=LINE('',#15882,#15881); -#15884=DIRECTION('',(-1.776356839400E-14,1.E0,0.E0)); -#15885=VECTOR('',#15884,5.E-2); -#15886=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.95E0)); -#15887=LINE('',#15886,#15885); -#15888=DIRECTION('',(-1.776356839400E-14,1.E0,3.552713678801E-14)); -#15889=VECTOR('',#15888,5.E-2); -#15890=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.55E0)); -#15891=LINE('',#15890,#15889); -#15892=DIRECTION('',(0.E0,1.E0,0.E0)); -#15893=VECTOR('',#15892,5.E-1); -#15894=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,8.55E0)); -#15895=LINE('',#15894,#15893); -#15896=DIRECTION('',(1.776356839400E-14,1.E0,0.E0)); -#15897=VECTOR('',#15896,5.E-2); -#15898=CARTESIAN_POINT('',(-6.5E0,2.5E-1,8.55E0)); -#15899=LINE('',#15898,#15897); -#15900=DIRECTION('',(1.776356839400E-14,1.E0,0.E0)); -#15901=VECTOR('',#15900,5.E-2); -#15902=CARTESIAN_POINT('',(-6.5E0,2.5E-1,8.95E0)); -#15903=LINE('',#15902,#15901); -#15904=DIRECTION('',(0.E0,1.E0,0.E0)); -#15905=VECTOR('',#15904,5.E-1); -#15906=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,8.95E0)); -#15907=LINE('',#15906,#15905); -#15908=DIRECTION('',(-1.776356839400E-14,1.E0,-3.552713678801E-14)); -#15909=VECTOR('',#15908,5.E-2); -#15910=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.005E1)); -#15911=LINE('',#15910,#15909); -#15912=DIRECTION('',(-1.776356839400E-14,1.E0,3.552713678801E-14)); -#15913=VECTOR('',#15912,5.E-2); -#15914=CARTESIAN_POINT('',(-6.5E0,-3.E-1,9.65E0)); -#15915=LINE('',#15914,#15913); -#15916=DIRECTION('',(0.E0,1.E0,0.E0)); -#15917=VECTOR('',#15916,5.E-1); -#15918=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,9.65E0)); -#15919=LINE('',#15918,#15917); -#15920=DIRECTION('',(1.776356839400E-14,1.E0,-3.552713678801E-14)); -#15921=VECTOR('',#15920,5.E-2); -#15922=CARTESIAN_POINT('',(-6.5E0,2.5E-1,9.65E0)); -#15923=LINE('',#15922,#15921); -#15924=DIRECTION('',(1.776356839400E-14,1.E0,0.E0)); -#15925=VECTOR('',#15924,5.E-2); -#15926=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.005E1)); -#15927=LINE('',#15926,#15925); -#15928=DIRECTION('',(0.E0,1.E0,0.E0)); -#15929=VECTOR('',#15928,5.E-1); -#15930=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.005E1)); -#15931=LINE('',#15930,#15929); -#15932=DIRECTION('',(-3.552713678801E-14,1.E0,0.E0)); -#15933=VECTOR('',#15932,5.E-2); -#15934=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.115E1)); -#15935=LINE('',#15934,#15933); -#15936=DIRECTION('',(-3.552713678801E-14,1.E0,0.E0)); -#15937=VECTOR('',#15936,5.E-2); -#15938=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.075E1)); -#15939=LINE('',#15938,#15937); -#15940=DIRECTION('',(0.E0,1.E0,0.E0)); -#15941=VECTOR('',#15940,5.E-1); -#15942=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.075E1)); -#15943=LINE('',#15942,#15941); -#15944=DIRECTION('',(3.552713678801E-14,1.E0,-3.552713678801E-14)); -#15945=VECTOR('',#15944,5.E-2); -#15946=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.075E1)); -#15947=LINE('',#15946,#15945); -#15948=DIRECTION('',(3.552713678801E-14,1.E0,0.E0)); -#15949=VECTOR('',#15948,5.E-2); -#15950=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.115E1)); -#15951=LINE('',#15950,#15949); -#15952=DIRECTION('',(0.E0,1.E0,0.E0)); -#15953=VECTOR('',#15952,5.E-1); -#15954=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.115E1)); -#15955=LINE('',#15954,#15953); -#15956=DIRECTION('',(-1.776356839400E-14,1.E0,0.E0)); -#15957=VECTOR('',#15956,5.E-2); -#15958=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.225E1)); -#15959=LINE('',#15958,#15957); -#15960=DIRECTION('',(-3.552713678801E-14,1.E0,0.E0)); -#15961=VECTOR('',#15960,5.E-2); -#15962=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.185E1)); -#15963=LINE('',#15962,#15961); -#15964=DIRECTION('',(0.E0,1.E0,0.E0)); -#15965=VECTOR('',#15964,5.E-1); -#15966=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.185E1)); -#15967=LINE('',#15966,#15965); -#15968=DIRECTION('',(3.552713678801E-14,1.E0,0.E0)); -#15969=VECTOR('',#15968,5.E-2); -#15970=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.185E1)); -#15971=LINE('',#15970,#15969); -#15972=DIRECTION('',(1.776356839400E-14,1.E0,0.E0)); -#15973=VECTOR('',#15972,5.E-2); -#15974=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.225E1)); -#15975=LINE('',#15974,#15973); -#15976=DIRECTION('',(0.E0,1.E0,0.E0)); -#15977=VECTOR('',#15976,5.E-1); -#15978=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.225E1)); -#15979=LINE('',#15978,#15977); -#15980=DIRECTION('',(3.552713678801E-14,1.E0,3.552713678801E-14)); -#15981=VECTOR('',#15980,5.E-2); -#15982=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.295E1)); -#15983=LINE('',#15982,#15981); -#15984=DIRECTION('',(-3.552713678801E-14,1.E0,3.552713678801E-14)); -#15985=VECTOR('',#15984,5.E-2); -#15986=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.295E1)); -#15987=LINE('',#15986,#15985); -#15988=DIRECTION('',(0.E0,1.E0,0.E0)); -#15989=VECTOR('',#15988,5.E-1); -#15990=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.295E1)); -#15991=LINE('',#15990,#15989); -#15992=DIRECTION('',(-1.E0,0.E0,0.E0)); -#15993=VECTOR('',#15992,6.E-1); -#15994=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,4.55E0)); -#15995=LINE('',#15994,#15993); -#15996=DIRECTION('',(0.E0,-1.E0,0.E0)); -#15997=VECTOR('',#15996,5.E-2); -#15998=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,4.55E0)); -#15999=LINE('',#15998,#15997); -#16000=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16001=VECTOR('',#16000,6.E-1); -#16002=CARTESIAN_POINT('',(-5.9E0,2.5E-1,4.55E0)); -#16003=LINE('',#16002,#16001); -#16004=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#16005=VECTOR('',#16004,5.E-2); -#16006=CARTESIAN_POINT('',(-5.9E0,3.E-1,4.55E0)); -#16007=LINE('',#16006,#16005); -#16008=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16009=VECTOR('',#16008,7.E-1); -#16010=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.25E0)); -#16011=LINE('',#16010,#16009); -#16012=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16013=VECTOR('',#16012,5.E-2); -#16014=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.25E0)); -#16015=LINE('',#16014,#16013); -#16016=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16017=VECTOR('',#16016,7.E-1); -#16018=CARTESIAN_POINT('',(-5.9E0,2.5E-1,5.25E0)); -#16019=LINE('',#16018,#16017); -#16020=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16021=VECTOR('',#16020,5.E-2); -#16022=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.25E0)); -#16023=LINE('',#16022,#16021); -#16024=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,4.9E0)); -#16025=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16026=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16027=AXIS2_PLACEMENT_3D('',#16024,#16025,#16026); -#16029=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,4.9E0)); -#16030=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16031=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16032=AXIS2_PLACEMENT_3D('',#16029,#16030,#16031); -#16034=DIRECTION('',(1.E0,0.E0,0.E0)); -#16035=VECTOR('',#16034,6.E-1); -#16036=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.25E0)); -#16037=LINE('',#16036,#16035); -#16038=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16039=VECTOR('',#16038,5.E-2); -#16040=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.25E0)); -#16041=LINE('',#16040,#16039); -#16042=DIRECTION('',(1.E0,0.E0,0.E0)); -#16043=VECTOR('',#16042,6.E-1); -#16044=CARTESIAN_POINT('',(6.9E0,2.5E-1,5.25E0)); -#16045=LINE('',#16044,#16043); -#16046=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16047=VECTOR('',#16046,5.E-2); -#16048=CARTESIAN_POINT('',(6.9E0,3.E-1,5.25E0)); -#16049=LINE('',#16048,#16047); -#16050=DIRECTION('',(0.E0,0.E0,1.E0)); -#16051=VECTOR('',#16050,7.E-1); -#16052=CARTESIAN_POINT('',(6.9E0,-2.5E-1,4.55E0)); -#16053=LINE('',#16052,#16051); -#16054=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16055=VECTOR('',#16054,5.E-2); -#16056=CARTESIAN_POINT('',(6.9E0,-2.5E-1,4.55E0)); -#16057=LINE('',#16056,#16055); -#16058=DIRECTION('',(0.E0,0.E0,1.E0)); -#16059=VECTOR('',#16058,7.E-1); -#16060=CARTESIAN_POINT('',(6.9E0,2.5E-1,4.55E0)); -#16061=LINE('',#16060,#16059); -#16062=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16063=VECTOR('',#16062,5.E-2); -#16064=CARTESIAN_POINT('',(6.9E0,3.E-1,4.55E0)); -#16065=LINE('',#16064,#16063); -#16066=DIRECTION('',(0.E0,1.E0,0.E0)); -#16067=VECTOR('',#16066,6.E-1); -#16068=CARTESIAN_POINT('',(-7.5E0,-3.E-1,1.E0)); -#16069=LINE('',#16068,#16067); -#16070=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16071=VECTOR('',#16070,6.E-1); -#16072=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.65E0)); -#16073=LINE('',#16072,#16071); -#16074=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16075=VECTOR('',#16074,5.E-2); -#16076=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.65E0)); -#16077=LINE('',#16076,#16075); -#16078=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16079=VECTOR('',#16078,6.E-1); -#16080=CARTESIAN_POINT('',(-5.9E0,2.5E-1,5.65E0)); -#16081=LINE('',#16080,#16079); -#16082=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16083=VECTOR('',#16082,5.E-2); -#16084=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.65E0)); -#16085=LINE('',#16084,#16083); -#16086=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,6.E0)); -#16087=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16088=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16089=AXIS2_PLACEMENT_3D('',#16086,#16087,#16088); -#16091=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,6.E0)); -#16092=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16093=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16094=AXIS2_PLACEMENT_3D('',#16091,#16092,#16093); -#16096=DIRECTION('',(1.E0,0.E0,0.E0)); -#16097=VECTOR('',#16096,6.E-1); -#16098=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,6.35E0)); -#16099=LINE('',#16098,#16097); -#16100=DIRECTION('',(1.E0,0.E0,0.E0)); -#16101=VECTOR('',#16100,6.E-1); -#16102=CARTESIAN_POINT('',(-6.5E0,2.5E-1,6.35E0)); -#16103=LINE('',#16102,#16101); -#16104=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16105=VECTOR('',#16104,7.E-1); -#16106=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.35E0)); -#16107=LINE('',#16106,#16105); -#16108=DIRECTION('',(0.E0,-1.E0,1.776356839400E-14)); -#16109=VECTOR('',#16108,5.E-2); -#16110=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.35E0)); -#16111=LINE('',#16110,#16109); -#16112=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16113=VECTOR('',#16112,7.E-1); -#16114=CARTESIAN_POINT('',(-5.9E0,2.5E-1,6.35E0)); -#16115=LINE('',#16114,#16113); -#16116=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#16117=VECTOR('',#16116,5.E-2); -#16118=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.35E0)); -#16119=LINE('',#16118,#16117); -#16120=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,6.E0)); -#16121=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16122=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16123=AXIS2_PLACEMENT_3D('',#16120,#16121,#16122); -#16125=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,6.E0)); -#16126=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16127=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16128=AXIS2_PLACEMENT_3D('',#16125,#16126,#16127); -#16130=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16131=VECTOR('',#16130,6.E-1); -#16132=CARTESIAN_POINT('',(7.5E0,-2.5E-1,5.65E0)); -#16133=LINE('',#16132,#16131); -#16134=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16135=VECTOR('',#16134,6.E-1); -#16136=CARTESIAN_POINT('',(7.5E0,2.5E-1,5.65E0)); -#16137=LINE('',#16136,#16135); -#16138=DIRECTION('',(0.E0,0.E0,1.E0)); -#16139=VECTOR('',#16138,7.E-1); -#16140=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.65E0)); -#16141=LINE('',#16140,#16139); -#16142=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16143=VECTOR('',#16142,5.E-2); -#16144=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.65E0)); -#16145=LINE('',#16144,#16143); -#16146=DIRECTION('',(0.E0,0.E0,1.E0)); -#16147=VECTOR('',#16146,7.E-1); -#16148=CARTESIAN_POINT('',(6.9E0,2.5E-1,5.65E0)); -#16149=LINE('',#16148,#16147); -#16150=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16151=VECTOR('',#16150,5.E-2); -#16152=CARTESIAN_POINT('',(6.9E0,3.E-1,5.65E0)); -#16153=LINE('',#16152,#16151); -#16154=DIRECTION('',(1.E0,0.E0,0.E0)); -#16155=VECTOR('',#16154,6.E-1); -#16156=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.35E0)); -#16157=LINE('',#16156,#16155); -#16158=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16159=VECTOR('',#16158,5.E-2); -#16160=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.35E0)); -#16161=LINE('',#16160,#16159); -#16162=DIRECTION('',(1.E0,0.E0,0.E0)); -#16163=VECTOR('',#16162,6.E-1); -#16164=CARTESIAN_POINT('',(6.9E0,2.5E-1,6.35E0)); -#16165=LINE('',#16164,#16163); -#16166=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16167=VECTOR('',#16166,5.E-2); -#16168=CARTESIAN_POINT('',(6.9E0,3.E-1,6.35E0)); -#16169=LINE('',#16168,#16167); -#16170=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16171=VECTOR('',#16170,6.E-1); -#16172=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.75E0)); -#16173=LINE('',#16172,#16171); -#16174=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16175=VECTOR('',#16174,5.E-2); -#16176=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.75E0)); -#16177=LINE('',#16176,#16175); -#16178=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16179=VECTOR('',#16178,6.E-1); -#16180=CARTESIAN_POINT('',(-5.9E0,2.5E-1,6.75E0)); -#16181=LINE('',#16180,#16179); -#16182=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16183=VECTOR('',#16182,5.E-2); -#16184=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.75E0)); -#16185=LINE('',#16184,#16183); -#16186=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,7.1E0)); -#16187=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16188=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16189=AXIS2_PLACEMENT_3D('',#16186,#16187,#16188); -#16191=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,7.1E0)); -#16192=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16193=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16194=AXIS2_PLACEMENT_3D('',#16191,#16192,#16193); -#16196=DIRECTION('',(1.E0,0.E0,0.E0)); -#16197=VECTOR('',#16196,6.E-1); -#16198=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,7.45E0)); -#16199=LINE('',#16198,#16197); -#16200=DIRECTION('',(1.E0,0.E0,0.E0)); -#16201=VECTOR('',#16200,6.E-1); -#16202=CARTESIAN_POINT('',(-6.5E0,2.5E-1,7.45E0)); -#16203=LINE('',#16202,#16201); -#16204=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16205=VECTOR('',#16204,7.E-1); -#16206=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.45E0)); -#16207=LINE('',#16206,#16205); -#16208=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16209=VECTOR('',#16208,5.E-2); -#16210=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.45E0)); -#16211=LINE('',#16210,#16209); -#16212=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16213=VECTOR('',#16212,7.E-1); -#16214=CARTESIAN_POINT('',(-5.9E0,2.5E-1,7.45E0)); -#16215=LINE('',#16214,#16213); -#16216=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16217=VECTOR('',#16216,5.E-2); -#16218=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.45E0)); -#16219=LINE('',#16218,#16217); -#16220=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,7.1E0)); -#16221=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16222=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16223=AXIS2_PLACEMENT_3D('',#16220,#16221,#16222); -#16225=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,7.1E0)); -#16226=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16227=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16228=AXIS2_PLACEMENT_3D('',#16225,#16226,#16227); -#16230=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16231=VECTOR('',#16230,6.E-1); -#16232=CARTESIAN_POINT('',(7.5E0,-2.5E-1,6.75E0)); -#16233=LINE('',#16232,#16231); -#16234=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16235=VECTOR('',#16234,6.E-1); -#16236=CARTESIAN_POINT('',(7.5E0,2.5E-1,6.75E0)); -#16237=LINE('',#16236,#16235); -#16238=DIRECTION('',(0.E0,0.E0,1.E0)); -#16239=VECTOR('',#16238,7.E-1); -#16240=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.75E0)); -#16241=LINE('',#16240,#16239); -#16242=DIRECTION('',(1.776356839400E-14,-1.E0,0.E0)); -#16243=VECTOR('',#16242,5.E-2); -#16244=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.75E0)); -#16245=LINE('',#16244,#16243); -#16246=DIRECTION('',(0.E0,0.E0,1.E0)); -#16247=VECTOR('',#16246,7.E-1); -#16248=CARTESIAN_POINT('',(6.9E0,2.5E-1,6.75E0)); -#16249=LINE('',#16248,#16247); -#16250=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16251=VECTOR('',#16250,5.E-2); -#16252=CARTESIAN_POINT('',(6.9E0,3.E-1,6.75E0)); -#16253=LINE('',#16252,#16251); -#16254=DIRECTION('',(1.E0,0.E0,0.E0)); -#16255=VECTOR('',#16254,6.E-1); -#16256=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.45E0)); -#16257=LINE('',#16256,#16255); -#16258=DIRECTION('',(0.E0,-1.E0,-1.776356839400E-14)); -#16259=VECTOR('',#16258,5.E-2); -#16260=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.45E0)); -#16261=LINE('',#16260,#16259); -#16262=DIRECTION('',(1.E0,0.E0,0.E0)); -#16263=VECTOR('',#16262,6.E-1); -#16264=CARTESIAN_POINT('',(6.9E0,2.5E-1,7.45E0)); -#16265=LINE('',#16264,#16263); -#16266=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16267=VECTOR('',#16266,5.E-2); -#16268=CARTESIAN_POINT('',(6.9E0,3.E-1,7.45E0)); -#16269=LINE('',#16268,#16267); -#16270=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16271=VECTOR('',#16270,6.E-1); -#16272=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.85E0)); -#16273=LINE('',#16272,#16271); -#16274=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16275=VECTOR('',#16274,5.E-2); -#16276=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.85E0)); -#16277=LINE('',#16276,#16275); -#16278=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16279=VECTOR('',#16278,6.E-1); -#16280=CARTESIAN_POINT('',(-5.9E0,2.5E-1,7.85E0)); -#16281=LINE('',#16280,#16279); -#16282=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16283=VECTOR('',#16282,5.E-2); -#16284=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.85E0)); -#16285=LINE('',#16284,#16283); -#16286=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,8.2E0)); -#16287=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16288=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16289=AXIS2_PLACEMENT_3D('',#16286,#16287,#16288); -#16291=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,8.2E0)); -#16292=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16293=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16294=AXIS2_PLACEMENT_3D('',#16291,#16292,#16293); -#16296=DIRECTION('',(1.E0,0.E0,0.E0)); -#16297=VECTOR('',#16296,6.E-1); -#16298=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,8.55E0)); -#16299=LINE('',#16298,#16297); -#16300=DIRECTION('',(1.E0,0.E0,0.E0)); -#16301=VECTOR('',#16300,6.E-1); -#16302=CARTESIAN_POINT('',(-6.5E0,2.5E-1,8.55E0)); -#16303=LINE('',#16302,#16301); -#16304=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16305=VECTOR('',#16304,7.E-1); -#16306=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.55E0)); -#16307=LINE('',#16306,#16305); -#16308=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16309=VECTOR('',#16308,5.E-2); -#16310=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.55E0)); -#16311=LINE('',#16310,#16309); -#16312=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16313=VECTOR('',#16312,7.E-1); -#16314=CARTESIAN_POINT('',(-5.9E0,2.5E-1,8.55E0)); -#16315=LINE('',#16314,#16313); -#16316=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16317=VECTOR('',#16316,5.E-2); -#16318=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.55E0)); -#16319=LINE('',#16318,#16317); -#16320=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,8.2E0)); -#16321=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16322=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16323=AXIS2_PLACEMENT_3D('',#16320,#16321,#16322); -#16325=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,8.2E0)); -#16326=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16327=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16328=AXIS2_PLACEMENT_3D('',#16325,#16326,#16327); -#16330=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16331=VECTOR('',#16330,6.E-1); -#16332=CARTESIAN_POINT('',(7.5E0,-2.5E-1,7.85E0)); -#16333=LINE('',#16332,#16331); -#16334=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16335=VECTOR('',#16334,6.E-1); -#16336=CARTESIAN_POINT('',(7.5E0,2.5E-1,7.85E0)); -#16337=LINE('',#16336,#16335); -#16338=DIRECTION('',(0.E0,0.E0,1.E0)); -#16339=VECTOR('',#16338,7.E-1); -#16340=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.85E0)); -#16341=LINE('',#16340,#16339); -#16342=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16343=VECTOR('',#16342,5.E-2); -#16344=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.85E0)); -#16345=LINE('',#16344,#16343); -#16346=DIRECTION('',(0.E0,0.E0,1.E0)); -#16347=VECTOR('',#16346,7.E-1); -#16348=CARTESIAN_POINT('',(6.9E0,2.5E-1,7.85E0)); -#16349=LINE('',#16348,#16347); -#16350=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16351=VECTOR('',#16350,5.E-2); -#16352=CARTESIAN_POINT('',(6.9E0,3.E-1,7.85E0)); -#16353=LINE('',#16352,#16351); -#16354=DIRECTION('',(1.E0,0.E0,0.E0)); -#16355=VECTOR('',#16354,6.E-1); -#16356=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.55E0)); -#16357=LINE('',#16356,#16355); -#16358=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16359=VECTOR('',#16358,5.E-2); -#16360=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.55E0)); -#16361=LINE('',#16360,#16359); -#16362=DIRECTION('',(1.E0,0.E0,0.E0)); -#16363=VECTOR('',#16362,6.E-1); -#16364=CARTESIAN_POINT('',(6.9E0,2.5E-1,8.55E0)); -#16365=LINE('',#16364,#16363); -#16366=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16367=VECTOR('',#16366,5.E-2); -#16368=CARTESIAN_POINT('',(6.9E0,3.E-1,8.55E0)); -#16369=LINE('',#16368,#16367); -#16370=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16371=VECTOR('',#16370,6.E-1); -#16372=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.95E0)); -#16373=LINE('',#16372,#16371); -#16374=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#16375=VECTOR('',#16374,5.E-2); -#16376=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.95E0)); -#16377=LINE('',#16376,#16375); -#16378=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16379=VECTOR('',#16378,6.E-1); -#16380=CARTESIAN_POINT('',(-5.9E0,2.5E-1,8.95E0)); -#16381=LINE('',#16380,#16379); -#16382=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16383=VECTOR('',#16382,5.E-2); -#16384=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.95E0)); -#16385=LINE('',#16384,#16383); -#16386=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,9.3E0)); -#16387=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16388=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16389=AXIS2_PLACEMENT_3D('',#16386,#16387,#16388); -#16391=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,9.3E0)); -#16392=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16393=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16394=AXIS2_PLACEMENT_3D('',#16391,#16392,#16393); -#16396=DIRECTION('',(1.E0,0.E0,0.E0)); -#16397=VECTOR('',#16396,6.E-1); -#16398=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,9.65E0)); -#16399=LINE('',#16398,#16397); -#16400=DIRECTION('',(1.E0,0.E0,0.E0)); -#16401=VECTOR('',#16400,6.E-1); -#16402=CARTESIAN_POINT('',(-6.5E0,2.5E-1,9.65E0)); -#16403=LINE('',#16402,#16401); -#16404=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16405=VECTOR('',#16404,7.E-1); -#16406=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,9.65E0)); -#16407=LINE('',#16406,#16405); -#16408=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16409=VECTOR('',#16408,5.E-2); -#16410=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,9.65E0)); -#16411=LINE('',#16410,#16409); -#16412=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16413=VECTOR('',#16412,7.E-1); -#16414=CARTESIAN_POINT('',(-5.9E0,2.5E-1,9.65E0)); -#16415=LINE('',#16414,#16413); -#16416=DIRECTION('',(0.E0,-1.E0,3.552713678801E-14)); -#16417=VECTOR('',#16416,5.E-2); -#16418=CARTESIAN_POINT('',(-5.9E0,3.E-1,9.65E0)); -#16419=LINE('',#16418,#16417); -#16420=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,9.3E0)); -#16421=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16422=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16423=AXIS2_PLACEMENT_3D('',#16420,#16421,#16422); -#16425=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,9.3E0)); -#16426=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16427=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16428=AXIS2_PLACEMENT_3D('',#16425,#16426,#16427); -#16430=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16431=VECTOR('',#16430,6.E-1); -#16432=CARTESIAN_POINT('',(7.5E0,-2.5E-1,8.95E0)); -#16433=LINE('',#16432,#16431); -#16434=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16435=VECTOR('',#16434,6.E-1); -#16436=CARTESIAN_POINT('',(7.5E0,2.5E-1,8.95E0)); -#16437=LINE('',#16436,#16435); -#16438=DIRECTION('',(0.E0,0.E0,1.E0)); -#16439=VECTOR('',#16438,7.E-1); -#16440=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.95E0)); -#16441=LINE('',#16440,#16439); -#16442=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16443=VECTOR('',#16442,5.E-2); -#16444=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.95E0)); -#16445=LINE('',#16444,#16443); -#16446=DIRECTION('',(0.E0,0.E0,1.E0)); -#16447=VECTOR('',#16446,7.E-1); -#16448=CARTESIAN_POINT('',(6.9E0,2.5E-1,8.95E0)); -#16449=LINE('',#16448,#16447); -#16450=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16451=VECTOR('',#16450,5.E-2); -#16452=CARTESIAN_POINT('',(6.9E0,3.E-1,8.95E0)); -#16453=LINE('',#16452,#16451); -#16454=DIRECTION('',(1.E0,0.E0,0.E0)); -#16455=VECTOR('',#16454,6.E-1); -#16456=CARTESIAN_POINT('',(6.9E0,-2.5E-1,9.65E0)); -#16457=LINE('',#16456,#16455); -#16458=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16459=VECTOR('',#16458,5.E-2); -#16460=CARTESIAN_POINT('',(6.9E0,-2.5E-1,9.65E0)); -#16461=LINE('',#16460,#16459); -#16462=DIRECTION('',(1.E0,0.E0,0.E0)); -#16463=VECTOR('',#16462,6.E-1); -#16464=CARTESIAN_POINT('',(6.9E0,2.5E-1,9.65E0)); -#16465=LINE('',#16464,#16463); -#16466=DIRECTION('',(0.E0,-1.E0,3.552713678801E-14)); -#16467=VECTOR('',#16466,5.E-2); -#16468=CARTESIAN_POINT('',(6.9E0,3.E-1,9.65E0)); -#16469=LINE('',#16468,#16467); -#16470=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16471=VECTOR('',#16470,6.E-1); -#16472=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.005E1)); -#16473=LINE('',#16472,#16471); -#16474=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#16475=VECTOR('',#16474,5.E-2); -#16476=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.005E1)); -#16477=LINE('',#16476,#16475); -#16478=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16479=VECTOR('',#16478,6.E-1); -#16480=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.005E1)); -#16481=LINE('',#16480,#16479); -#16482=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16483=VECTOR('',#16482,5.E-2); -#16484=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.005E1)); -#16485=LINE('',#16484,#16483); -#16486=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.04E1)); -#16487=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16488=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16489=AXIS2_PLACEMENT_3D('',#16486,#16487,#16488); -#16491=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.04E1)); -#16492=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16493=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16494=AXIS2_PLACEMENT_3D('',#16491,#16492,#16493); -#16496=DIRECTION('',(1.E0,0.E0,0.E0)); -#16497=VECTOR('',#16496,6.E-1); -#16498=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.075E1)); -#16499=LINE('',#16498,#16497); -#16500=DIRECTION('',(1.E0,0.E0,0.E0)); -#16501=VECTOR('',#16500,6.E-1); -#16502=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.075E1)); -#16503=LINE('',#16502,#16501); -#16504=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16505=VECTOR('',#16504,7.E-1); -#16506=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.075E1)); -#16507=LINE('',#16506,#16505); -#16508=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16509=VECTOR('',#16508,5.E-2); -#16510=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.075E1)); -#16511=LINE('',#16510,#16509); -#16512=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16513=VECTOR('',#16512,7.E-1); -#16514=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.075E1)); -#16515=LINE('',#16514,#16513); -#16516=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16517=VECTOR('',#16516,5.E-2); -#16518=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.075E1)); -#16519=LINE('',#16518,#16517); -#16520=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,1.04E1)); -#16521=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16522=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16523=AXIS2_PLACEMENT_3D('',#16520,#16521,#16522); -#16525=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,1.04E1)); -#16526=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16527=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16528=AXIS2_PLACEMENT_3D('',#16525,#16526,#16527); -#16530=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16531=VECTOR('',#16530,6.E-1); -#16532=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.005E1)); -#16533=LINE('',#16532,#16531); -#16534=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16535=VECTOR('',#16534,6.E-1); -#16536=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.005E1)); -#16537=LINE('',#16536,#16535); -#16538=DIRECTION('',(0.E0,0.E0,1.E0)); -#16539=VECTOR('',#16538,7.E-1); -#16540=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.005E1)); -#16541=LINE('',#16540,#16539); -#16542=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#16543=VECTOR('',#16542,5.E-2); -#16544=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.005E1)); -#16545=LINE('',#16544,#16543); -#16546=DIRECTION('',(0.E0,0.E0,1.E0)); -#16547=VECTOR('',#16546,7.E-1); -#16548=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.005E1)); -#16549=LINE('',#16548,#16547); -#16550=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16551=VECTOR('',#16550,5.E-2); -#16552=CARTESIAN_POINT('',(6.9E0,3.E-1,1.005E1)); -#16553=LINE('',#16552,#16551); -#16554=DIRECTION('',(1.E0,0.E0,0.E0)); -#16555=VECTOR('',#16554,6.E-1); -#16556=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.075E1)); -#16557=LINE('',#16556,#16555); -#16558=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16559=VECTOR('',#16558,5.E-2); -#16560=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.075E1)); -#16561=LINE('',#16560,#16559); -#16562=DIRECTION('',(1.E0,0.E0,0.E0)); -#16563=VECTOR('',#16562,6.E-1); -#16564=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.075E1)); -#16565=LINE('',#16564,#16563); -#16566=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16567=VECTOR('',#16566,5.E-2); -#16568=CARTESIAN_POINT('',(6.9E0,3.E-1,1.075E1)); -#16569=LINE('',#16568,#16567); -#16570=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16571=VECTOR('',#16570,6.E-1); -#16572=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.115E1)); -#16573=LINE('',#16572,#16571); -#16574=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#16575=VECTOR('',#16574,5.E-2); -#16576=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.115E1)); -#16577=LINE('',#16576,#16575); -#16578=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16579=VECTOR('',#16578,6.E-1); -#16580=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.115E1)); -#16581=LINE('',#16580,#16579); -#16582=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16583=VECTOR('',#16582,5.E-2); -#16584=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.115E1)); -#16585=LINE('',#16584,#16583); -#16586=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.15E1)); -#16587=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16588=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16589=AXIS2_PLACEMENT_3D('',#16586,#16587,#16588); -#16591=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.15E1)); -#16592=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16593=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16594=AXIS2_PLACEMENT_3D('',#16591,#16592,#16593); -#16596=DIRECTION('',(1.E0,0.E0,0.E0)); -#16597=VECTOR('',#16596,6.E-1); -#16598=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.185E1)); -#16599=LINE('',#16598,#16597); -#16600=DIRECTION('',(1.E0,0.E0,0.E0)); -#16601=VECTOR('',#16600,6.E-1); -#16602=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.185E1)); -#16603=LINE('',#16602,#16601); -#16604=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16605=VECTOR('',#16604,7.E-1); -#16606=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.185E1)); -#16607=LINE('',#16606,#16605); -#16608=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16609=VECTOR('',#16608,5.E-2); -#16610=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.185E1)); -#16611=LINE('',#16610,#16609); -#16612=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16613=VECTOR('',#16612,7.E-1); -#16614=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.185E1)); -#16615=LINE('',#16614,#16613); -#16616=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16617=VECTOR('',#16616,5.E-2); -#16618=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.185E1)); -#16619=LINE('',#16618,#16617); -#16620=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,1.15E1)); -#16621=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16622=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16623=AXIS2_PLACEMENT_3D('',#16620,#16621,#16622); -#16625=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,1.15E1)); -#16626=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16627=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16628=AXIS2_PLACEMENT_3D('',#16625,#16626,#16627); -#16630=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16631=VECTOR('',#16630,6.E-1); -#16632=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.115E1)); -#16633=LINE('',#16632,#16631); -#16634=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16635=VECTOR('',#16634,6.E-1); -#16636=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.115E1)); -#16637=LINE('',#16636,#16635); -#16638=DIRECTION('',(0.E0,0.E0,1.E0)); -#16639=VECTOR('',#16638,7.E-1); -#16640=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.115E1)); -#16641=LINE('',#16640,#16639); -#16642=DIRECTION('',(0.E0,-1.E0,3.552713678800E-14)); -#16643=VECTOR('',#16642,5.E-2); -#16644=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.115E1)); -#16645=LINE('',#16644,#16643); -#16646=DIRECTION('',(0.E0,0.E0,1.E0)); -#16647=VECTOR('',#16646,7.E-1); -#16648=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.115E1)); -#16649=LINE('',#16648,#16647); -#16650=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16651=VECTOR('',#16650,5.E-2); -#16652=CARTESIAN_POINT('',(6.9E0,3.E-1,1.115E1)); -#16653=LINE('',#16652,#16651); -#16654=DIRECTION('',(1.E0,0.E0,0.E0)); -#16655=VECTOR('',#16654,6.E-1); -#16656=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.185E1)); -#16657=LINE('',#16656,#16655); -#16658=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16659=VECTOR('',#16658,5.E-2); -#16660=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.185E1)); -#16661=LINE('',#16660,#16659); -#16662=DIRECTION('',(1.E0,0.E0,0.E0)); -#16663=VECTOR('',#16662,6.E-1); -#16664=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.185E1)); -#16665=LINE('',#16664,#16663); -#16666=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16667=VECTOR('',#16666,5.E-2); -#16668=CARTESIAN_POINT('',(6.9E0,3.E-1,1.185E1)); -#16669=LINE('',#16668,#16667); -#16670=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16671=VECTOR('',#16670,6.E-1); -#16672=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.225E1)); -#16673=LINE('',#16672,#16671); -#16674=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16675=VECTOR('',#16674,5.E-2); -#16676=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.225E1)); -#16677=LINE('',#16676,#16675); -#16678=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16679=VECTOR('',#16678,6.E-1); -#16680=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.225E1)); -#16681=LINE('',#16680,#16679); -#16682=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16683=VECTOR('',#16682,5.E-2); -#16684=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.225E1)); -#16685=LINE('',#16684,#16683); -#16686=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.26E1)); -#16687=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16688=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16689=AXIS2_PLACEMENT_3D('',#16686,#16687,#16688); -#16691=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.26E1)); -#16692=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16693=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16694=AXIS2_PLACEMENT_3D('',#16691,#16692,#16693); -#16696=DIRECTION('',(1.E0,0.E0,0.E0)); -#16697=VECTOR('',#16696,6.E-1); -#16698=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.295E1)); -#16699=LINE('',#16698,#16697); -#16700=DIRECTION('',(1.E0,0.E0,0.E0)); -#16701=VECTOR('',#16700,6.E-1); -#16702=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.295E1)); -#16703=LINE('',#16702,#16701); -#16704=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16705=VECTOR('',#16704,7.E-1); -#16706=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.295E1)); -#16707=LINE('',#16706,#16705); -#16708=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16709=VECTOR('',#16708,5.E-2); -#16710=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.295E1)); -#16711=LINE('',#16710,#16709); -#16712=DIRECTION('',(0.E0,0.E0,-1.E0)); -#16713=VECTOR('',#16712,7.E-1); -#16714=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.295E1)); -#16715=LINE('',#16714,#16713); -#16716=DIRECTION('',(0.E0,-1.E0,3.552713678801E-14)); -#16717=VECTOR('',#16716,5.E-2); -#16718=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.295E1)); -#16719=LINE('',#16718,#16717); -#16720=CARTESIAN_POINT('',(-6.693649167310E0,2.5E-1,1.26E1)); -#16721=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16722=DIRECTION('',(4.841229182759E-1,0.E0,-8.75E-1)); -#16723=AXIS2_PLACEMENT_3D('',#16720,#16721,#16722); -#16725=CARTESIAN_POINT('',(7.693649167310E0,2.5E-1,1.26E1)); -#16726=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16727=DIRECTION('',(-4.841229182759E-1,0.E0,8.75E-1)); -#16728=AXIS2_PLACEMENT_3D('',#16725,#16726,#16727); -#16730=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16731=VECTOR('',#16730,6.E-1); -#16732=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.225E1)); -#16733=LINE('',#16732,#16731); -#16734=DIRECTION('',(-1.E0,0.E0,0.E0)); -#16735=VECTOR('',#16734,6.E-1); -#16736=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.225E1)); -#16737=LINE('',#16736,#16735); -#16738=DIRECTION('',(0.E0,0.E0,1.E0)); -#16739=VECTOR('',#16738,7.E-1); -#16740=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.225E1)); -#16741=LINE('',#16740,#16739); -#16742=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16743=VECTOR('',#16742,5.E-2); -#16744=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.225E1)); -#16745=LINE('',#16744,#16743); -#16746=DIRECTION('',(0.E0,0.E0,1.E0)); -#16747=VECTOR('',#16746,7.E-1); -#16748=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.225E1)); -#16749=LINE('',#16748,#16747); -#16750=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16751=VECTOR('',#16750,5.E-2); -#16752=CARTESIAN_POINT('',(6.9E0,3.E-1,1.225E1)); -#16753=LINE('',#16752,#16751); -#16754=DIRECTION('',(1.E0,0.E0,0.E0)); -#16755=VECTOR('',#16754,6.E-1); -#16756=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.295E1)); -#16757=LINE('',#16756,#16755); -#16758=DIRECTION('',(0.E0,-1.E0,-3.552713678800E-14)); -#16759=VECTOR('',#16758,5.E-2); -#16760=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.295E1)); -#16761=LINE('',#16760,#16759); -#16762=DIRECTION('',(1.E0,0.E0,0.E0)); -#16763=VECTOR('',#16762,6.E-1); -#16764=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.295E1)); -#16765=LINE('',#16764,#16763); -#16766=DIRECTION('',(0.E0,-1.E0,-3.552713678801E-14)); -#16767=VECTOR('',#16766,5.E-2); -#16768=CARTESIAN_POINT('',(6.9E0,3.E-1,1.295E1)); -#16769=LINE('',#16768,#16767); -#16770=DIRECTION('',(0.E0,1.E0,0.E0)); -#16771=VECTOR('',#16770,6.E-1); -#16772=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.37E1)); -#16773=LINE('',#16772,#16771); -#16774=CARTESIAN_POINT('',(-7.55E0,-2.5E-1,-1.2635E1)); -#16775=DIRECTION('',(0.E0,1.E0,0.E0)); -#16776=DIRECTION('',(2.E-1,0.E0,9.797958971133E-1)); -#16777=AXIS2_PLACEMENT_3D('',#16774,#16775,#16776); -#16779=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.2635E1)); -#16780=DIRECTION('',(0.E0,-1.E0,0.E0)); -#16781=DIRECTION('',(2.E-1,0.E0,-9.797958971133E-1)); -#16782=AXIS2_PLACEMENT_3D('',#16779,#16780,#16781); -#16784=DIRECTION('',(0.E0,1.E0,0.E0)); -#16785=VECTOR('',#16784,5.E-2); -#16786=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2335E1)); -#16787=LINE('',#16786,#16785); -#16788=DIRECTION('',(0.E0,1.E0,0.E0)); -#16789=VECTOR('',#16788,5.E-2); -#16790=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2935E1)); -#16791=LINE('',#16790,#16789); -#16792=DIRECTION('',(0.E0,1.E0,0.E0)); -#16793=VECTOR('',#16792,5.E-2); -#16794=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.3435E1)); -#16795=LINE('',#16794,#16793); -#16796=CARTESIAN_POINT('',(-7.5E0,-3.E-1,1.E0)); -#16797=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#16798=VERTEX_POINT('',#16796); -#16799=VERTEX_POINT('',#16797); -#16800=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.37E1)); -#16801=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#16802=VERTEX_POINT('',#16800); -#16803=VERTEX_POINT('',#16801); -#16804=CARTESIAN_POINT('',(7.5E0,-3.E-1,-1.43E1)); -#16805=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#16806=VERTEX_POINT('',#16804); -#16807=VERTEX_POINT('',#16805); -#16808=CARTESIAN_POINT('',(-7.5E0,3.E-1,1.E0)); -#16809=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.E0)); -#16810=VERTEX_POINT('',#16808); -#16811=VERTEX_POINT('',#16809); -#16812=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.37E1)); -#16813=CARTESIAN_POINT('',(7.5E0,3.E-1,1.37E1)); -#16814=VERTEX_POINT('',#16812); -#16815=VERTEX_POINT('',#16813); -#16816=CARTESIAN_POINT('',(7.5E0,3.E-1,-1.43E1)); -#16817=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.43E1)); -#16818=VERTEX_POINT('',#16816); -#16819=VERTEX_POINT('',#16817); -#16820=CARTESIAN_POINT('',(-5.4E0,1.55E0,1.342E1)); -#16821=CARTESIAN_POINT('',(-5.4E0,1.55E0,-3.98E0)); -#16822=VERTEX_POINT('',#16820); -#16823=VERTEX_POINT('',#16821); -#16824=CARTESIAN_POINT('',(6.8E0,1.55E0,1.342E1)); -#16825=VERTEX_POINT('',#16824); -#16826=CARTESIAN_POINT('',(6.8E0,1.55E0,-3.98E0)); -#16827=VERTEX_POINT('',#16826); -#16828=CARTESIAN_POINT('',(-5.4E0,3.E-1,-3.98E0)); -#16829=VERTEX_POINT('',#16828); -#16830=CARTESIAN_POINT('',(-5.4E0,3.E-1,1.342E1)); -#16831=VERTEX_POINT('',#16830); -#16832=CARTESIAN_POINT('',(6.8E0,3.E-1,1.342E1)); -#16833=VERTEX_POINT('',#16832); -#16834=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.327E1)); -#16835=CARTESIAN_POINT('',(6.65E0,3.E-1,1.327E1)); -#16836=VERTEX_POINT('',#16834); -#16837=VERTEX_POINT('',#16835); -#16838=CARTESIAN_POINT('',(6.65E0,3.E-1,-8.436186517363E-2)); -#16839=CARTESIAN_POINT('',(6.65E0,3.E-1,-1.58E0)); -#16840=VERTEX_POINT('',#16838); -#16841=VERTEX_POINT('',#16839); -#16842=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.83E0)); -#16843=CARTESIAN_POINT('',(-5.25E0,3.E-1,-3.83E0)); -#16844=VERTEX_POINT('',#16842); -#16845=VERTEX_POINT('',#16843); -#16846=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.757618014356E0)); -#16847=CARTESIAN_POINT('',(-5.25E0,3.E-1,1.327E1)); -#16848=VERTEX_POINT('',#16846); -#16849=VERTEX_POINT('',#16847); -#16850=CARTESIAN_POINT('',(5.1E-1,1.4E0,1.327E1)); -#16851=CARTESIAN_POINT('',(6.65E0,1.4E0,1.327E1)); -#16852=VERTEX_POINT('',#16850); -#16853=VERTEX_POINT('',#16851); -#16854=CARTESIAN_POINT('',(6.65E0,1.4E0,-8.436186517363E-2)); -#16855=CARTESIAN_POINT('',(6.65E0,1.4E0,-1.58E0)); -#16856=VERTEX_POINT('',#16854); -#16857=VERTEX_POINT('',#16855); -#16858=CARTESIAN_POINT('',(-5.E-2,1.4E0,-3.83E0)); -#16859=CARTESIAN_POINT('',(-5.25E0,1.4E0,-3.83E0)); -#16860=VERTEX_POINT('',#16858); -#16861=VERTEX_POINT('',#16859); -#16862=CARTESIAN_POINT('',(-5.25E0,1.4E0,8.757618014356E0)); -#16863=CARTESIAN_POINT('',(-5.25E0,1.4E0,1.327E1)); -#16864=VERTEX_POINT('',#16862); -#16865=VERTEX_POINT('',#16863); -#16866=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.327E1)); -#16867=VERTEX_POINT('',#16866); -#16868=CARTESIAN_POINT('',(6.65E0,3.E-1,8.039068448582E0)); -#16869=VERTEX_POINT('',#16868); -#16870=CARTESIAN_POINT('',(6.65E0,3.E-1,5.639068448582E0)); -#16871=CARTESIAN_POINT('',(6.65E0,3.E-1,9.156381348264E-1)); -#16872=VERTEX_POINT('',#16870); -#16873=VERTEX_POINT('',#16871); -#16874=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.83E0)); -#16875=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.83E0)); -#16876=VERTEX_POINT('',#16874); -#16877=VERTEX_POINT('',#16875); -#16878=CARTESIAN_POINT('',(-5.25E0,3.E-1,-7.266321657252E-1)); -#16879=VERTEX_POINT('',#16878); -#16880=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.628565170500E-1)); -#16881=CARTESIAN_POINT('',(-5.25E0,3.E-1,6.861069017863E0)); -#16882=VERTEX_POINT('',#16880); -#16883=VERTEX_POINT('',#16881); -#16884=CARTESIAN_POINT('',(-4.9E-1,1.4E0,1.327E1)); -#16885=VERTEX_POINT('',#16884); -#16886=CARTESIAN_POINT('',(6.65E0,1.4E0,8.039068448582E0)); -#16887=VERTEX_POINT('',#16886); -#16888=CARTESIAN_POINT('',(6.65E0,1.4E0,5.639068448582E0)); -#16889=CARTESIAN_POINT('',(6.65E0,1.4E0,9.156381348264E-1)); -#16890=VERTEX_POINT('',#16888); -#16891=VERTEX_POINT('',#16889); -#16892=CARTESIAN_POINT('',(5.1E0,1.4E0,-3.83E0)); -#16893=CARTESIAN_POINT('',(6.E-1,1.4E0,-3.83E0)); -#16894=VERTEX_POINT('',#16892); -#16895=VERTEX_POINT('',#16893); -#16896=CARTESIAN_POINT('',(-5.25E0,1.4E0,-7.266321657252E-1)); -#16897=VERTEX_POINT('',#16896); -#16898=CARTESIAN_POINT('',(-5.25E0,1.4E0,8.628565170500E-1)); -#16899=CARTESIAN_POINT('',(-5.25E0,1.4E0,6.861069017863E0)); -#16900=VERTEX_POINT('',#16898); -#16901=VERTEX_POINT('',#16899); -#16902=CARTESIAN_POINT('',(-5.4E0,1.4E0,-7.266321657252E-1)); -#16903=CARTESIAN_POINT('',(-5.4E0,1.4E0,8.628565170500E-1)); -#16904=VERTEX_POINT('',#16902); -#16905=VERTEX_POINT('',#16903); -#16906=CARTESIAN_POINT('',(-5.4E0,1.4E0,6.861069017863E0)); -#16907=CARTESIAN_POINT('',(-5.4E0,1.4E0,8.757618014356E0)); -#16908=VERTEX_POINT('',#16906); -#16909=VERTEX_POINT('',#16907); -#16910=CARTESIAN_POINT('',(-5.4E0,3.E-1,-7.266321657252E-1)); -#16911=VERTEX_POINT('',#16910); -#16912=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.628565170500E-1)); -#16913=VERTEX_POINT('',#16912); -#16914=CARTESIAN_POINT('',(-5.4E0,3.E-1,6.861069017863E0)); -#16915=VERTEX_POINT('',#16914); -#16916=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.757618014356E0)); -#16917=VERTEX_POINT('',#16916); -#16918=CARTESIAN_POINT('',(-4.9E-1,1.4E0,1.342E1)); -#16919=CARTESIAN_POINT('',(5.1E-1,1.4E0,1.342E1)); -#16920=VERTEX_POINT('',#16918); -#16921=VERTEX_POINT('',#16919); -#16922=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.342E1)); -#16923=VERTEX_POINT('',#16922); -#16924=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.342E1)); -#16925=VERTEX_POINT('',#16924); -#16926=CARTESIAN_POINT('',(6.8E0,1.4E0,8.039068448582E0)); -#16927=CARTESIAN_POINT('',(6.8E0,1.4E0,5.639068448582E0)); -#16928=VERTEX_POINT('',#16926); -#16929=VERTEX_POINT('',#16927); -#16930=CARTESIAN_POINT('',(6.8E0,1.4E0,9.156381348264E-1)); -#16931=CARTESIAN_POINT('',(6.8E0,1.4E0,-8.436186517363E-2)); -#16932=VERTEX_POINT('',#16930); -#16933=VERTEX_POINT('',#16931); -#16934=CARTESIAN_POINT('',(6.8E0,1.4E0,-1.58E0)); -#16935=CARTESIAN_POINT('',(6.8E0,1.4E0,-3.98E0)); -#16936=VERTEX_POINT('',#16934); -#16937=VERTEX_POINT('',#16935); -#16938=CARTESIAN_POINT('',(6.8E0,3.E-1,8.039068448582E0)); -#16939=VERTEX_POINT('',#16938); -#16940=CARTESIAN_POINT('',(6.8E0,3.E-1,5.639068448582E0)); -#16941=VERTEX_POINT('',#16940); -#16942=CARTESIAN_POINT('',(6.8E0,3.E-1,9.156381348264E-1)); -#16943=VERTEX_POINT('',#16942); -#16944=CARTESIAN_POINT('',(6.8E0,3.E-1,-8.436186517363E-2)); -#16945=VERTEX_POINT('',#16944); -#16946=CARTESIAN_POINT('',(6.8E0,3.E-1,-1.58E0)); -#16947=VERTEX_POINT('',#16946); -#16948=CARTESIAN_POINT('',(5.1E0,1.4E0,-3.98E0)); -#16949=VERTEX_POINT('',#16948); -#16950=CARTESIAN_POINT('',(6.E-1,1.4E0,-3.98E0)); -#16951=CARTESIAN_POINT('',(-5.E-2,1.4E0,-3.98E0)); -#16952=VERTEX_POINT('',#16950); -#16953=VERTEX_POINT('',#16951); -#16954=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.98E0)); -#16955=VERTEX_POINT('',#16954); -#16956=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.98E0)); -#16957=VERTEX_POINT('',#16956); -#16958=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.98E0)); -#16959=VERTEX_POINT('',#16958); -#16960=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.295E1)); -#16961=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.295E1)); -#16962=VERTEX_POINT('',#16960); -#16963=VERTEX_POINT('',#16961); -#16964=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.225E1)); -#16965=VERTEX_POINT('',#16964); -#16966=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.225E1)); -#16967=VERTEX_POINT('',#16966); -#16968=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.225E1)); -#16969=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.225E1)); -#16970=VERTEX_POINT('',#16968); -#16971=VERTEX_POINT('',#16969); -#16972=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.295E1)); -#16973=VERTEX_POINT('',#16972); -#16974=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.295E1)); -#16975=VERTEX_POINT('',#16974); -#16976=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.295E1)); -#16977=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.295E1)); -#16978=VERTEX_POINT('',#16976); -#16979=VERTEX_POINT('',#16977); -#16980=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.225E1)); -#16981=VERTEX_POINT('',#16980); -#16982=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.225E1)); -#16983=VERTEX_POINT('',#16982); -#16984=CARTESIAN_POINT('',(7.5E0,3.E-1,1.225E1)); -#16985=CARTESIAN_POINT('',(6.9E0,3.E-1,1.225E1)); -#16986=VERTEX_POINT('',#16984); -#16987=VERTEX_POINT('',#16985); -#16988=CARTESIAN_POINT('',(7.5E0,3.E-1,1.295E1)); -#16989=CARTESIAN_POINT('',(6.9E0,3.E-1,1.295E1)); -#16990=VERTEX_POINT('',#16988); -#16991=VERTEX_POINT('',#16989); -#16992=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.185E1)); -#16993=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.185E1)); -#16994=VERTEX_POINT('',#16992); -#16995=VERTEX_POINT('',#16993); -#16996=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.115E1)); -#16997=VERTEX_POINT('',#16996); -#16998=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.115E1)); -#16999=VERTEX_POINT('',#16998); -#17000=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.115E1)); -#17001=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.115E1)); -#17002=VERTEX_POINT('',#17000); -#17003=VERTEX_POINT('',#17001); -#17004=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.185E1)); -#17005=VERTEX_POINT('',#17004); -#17006=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.185E1)); -#17007=VERTEX_POINT('',#17006); -#17008=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.185E1)); -#17009=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.185E1)); -#17010=VERTEX_POINT('',#17008); -#17011=VERTEX_POINT('',#17009); -#17012=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.115E1)); -#17013=VERTEX_POINT('',#17012); -#17014=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.115E1)); -#17015=VERTEX_POINT('',#17014); -#17016=CARTESIAN_POINT('',(7.5E0,3.E-1,1.115E1)); -#17017=CARTESIAN_POINT('',(6.9E0,3.E-1,1.115E1)); -#17018=VERTEX_POINT('',#17016); -#17019=VERTEX_POINT('',#17017); -#17020=CARTESIAN_POINT('',(6.9E0,3.E-1,1.185E1)); -#17021=VERTEX_POINT('',#17020); -#17022=CARTESIAN_POINT('',(7.5E0,3.E-1,1.185E1)); -#17023=VERTEX_POINT('',#17022); -#17024=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.075E1)); -#17025=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.075E1)); -#17026=VERTEX_POINT('',#17024); -#17027=VERTEX_POINT('',#17025); -#17028=CARTESIAN_POINT('',(-5.9E0,-3.E-1,1.005E1)); -#17029=VERTEX_POINT('',#17028); -#17030=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.005E1)); -#17031=VERTEX_POINT('',#17030); -#17032=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.005E1)); -#17033=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.005E1)); -#17034=VERTEX_POINT('',#17032); -#17035=VERTEX_POINT('',#17033); -#17036=CARTESIAN_POINT('',(6.9E0,-3.E-1,1.075E1)); -#17037=VERTEX_POINT('',#17036); -#17038=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.075E1)); -#17039=VERTEX_POINT('',#17038); -#17040=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.075E1)); -#17041=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.075E1)); -#17042=VERTEX_POINT('',#17040); -#17043=VERTEX_POINT('',#17041); -#17044=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.005E1)); -#17045=VERTEX_POINT('',#17044); -#17046=CARTESIAN_POINT('',(-6.5E0,3.E-1,1.005E1)); -#17047=VERTEX_POINT('',#17046); -#17048=CARTESIAN_POINT('',(7.5E0,3.E-1,1.005E1)); -#17049=CARTESIAN_POINT('',(6.9E0,3.E-1,1.005E1)); -#17050=VERTEX_POINT('',#17048); -#17051=VERTEX_POINT('',#17049); -#17052=CARTESIAN_POINT('',(6.9E0,3.E-1,1.075E1)); -#17053=VERTEX_POINT('',#17052); -#17054=CARTESIAN_POINT('',(7.5E0,3.E-1,1.075E1)); -#17055=VERTEX_POINT('',#17054); -#17056=CARTESIAN_POINT('',(-6.5E0,-3.E-1,9.65E0)); -#17057=CARTESIAN_POINT('',(-5.9E0,-3.E-1,9.65E0)); -#17058=VERTEX_POINT('',#17056); -#17059=VERTEX_POINT('',#17057); -#17060=CARTESIAN_POINT('',(-5.9E0,-3.E-1,8.95E0)); -#17061=VERTEX_POINT('',#17060); -#17062=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.95E0)); -#17063=VERTEX_POINT('',#17062); -#17064=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.95E0)); -#17065=CARTESIAN_POINT('',(6.9E0,-3.E-1,8.95E0)); -#17066=VERTEX_POINT('',#17064); -#17067=VERTEX_POINT('',#17065); -#17068=CARTESIAN_POINT('',(6.9E0,-3.E-1,9.65E0)); -#17069=VERTEX_POINT('',#17068); -#17070=CARTESIAN_POINT('',(7.5E0,-3.E-1,9.65E0)); -#17071=VERTEX_POINT('',#17070); -#17072=CARTESIAN_POINT('',(-6.5E0,3.E-1,9.65E0)); -#17073=CARTESIAN_POINT('',(-5.9E0,3.E-1,9.65E0)); -#17074=VERTEX_POINT('',#17072); -#17075=VERTEX_POINT('',#17073); -#17076=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.95E0)); -#17077=VERTEX_POINT('',#17076); -#17078=CARTESIAN_POINT('',(-6.5E0,3.E-1,8.95E0)); -#17079=VERTEX_POINT('',#17078); -#17080=CARTESIAN_POINT('',(7.5E0,3.E-1,8.95E0)); -#17081=CARTESIAN_POINT('',(6.9E0,3.E-1,8.95E0)); -#17082=VERTEX_POINT('',#17080); -#17083=VERTEX_POINT('',#17081); -#17084=CARTESIAN_POINT('',(6.9E0,3.E-1,9.65E0)); -#17085=VERTEX_POINT('',#17084); -#17086=CARTESIAN_POINT('',(7.5E0,3.E-1,9.65E0)); -#17087=VERTEX_POINT('',#17086); -#17088=CARTESIAN_POINT('',(-6.5E0,-3.E-1,8.55E0)); -#17089=CARTESIAN_POINT('',(-5.9E0,-3.E-1,8.55E0)); -#17090=VERTEX_POINT('',#17088); -#17091=VERTEX_POINT('',#17089); -#17092=CARTESIAN_POINT('',(-5.9E0,-3.E-1,7.85E0)); -#17093=VERTEX_POINT('',#17092); -#17094=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.85E0)); -#17095=VERTEX_POINT('',#17094); -#17096=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.85E0)); -#17097=CARTESIAN_POINT('',(6.9E0,-3.E-1,7.85E0)); -#17098=VERTEX_POINT('',#17096); -#17099=VERTEX_POINT('',#17097); -#17100=CARTESIAN_POINT('',(6.9E0,-3.E-1,8.55E0)); -#17101=VERTEX_POINT('',#17100); -#17102=CARTESIAN_POINT('',(7.5E0,-3.E-1,8.55E0)); -#17103=VERTEX_POINT('',#17102); -#17104=CARTESIAN_POINT('',(-6.5E0,3.E-1,8.55E0)); -#17105=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.55E0)); -#17106=VERTEX_POINT('',#17104); -#17107=VERTEX_POINT('',#17105); -#17108=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.85E0)); -#17109=VERTEX_POINT('',#17108); -#17110=CARTESIAN_POINT('',(-6.5E0,3.E-1,7.85E0)); -#17111=VERTEX_POINT('',#17110); -#17112=CARTESIAN_POINT('',(7.5E0,3.E-1,7.85E0)); -#17113=CARTESIAN_POINT('',(6.9E0,3.E-1,7.85E0)); -#17114=VERTEX_POINT('',#17112); -#17115=VERTEX_POINT('',#17113); -#17116=CARTESIAN_POINT('',(6.9E0,3.E-1,8.55E0)); -#17117=VERTEX_POINT('',#17116); -#17118=CARTESIAN_POINT('',(7.5E0,3.E-1,8.55E0)); -#17119=VERTEX_POINT('',#17118); -#17120=CARTESIAN_POINT('',(-6.5E0,-3.E-1,7.45E0)); -#17121=CARTESIAN_POINT('',(-5.9E0,-3.E-1,7.45E0)); -#17122=VERTEX_POINT('',#17120); -#17123=VERTEX_POINT('',#17121); -#17124=CARTESIAN_POINT('',(-5.9E0,-3.E-1,6.75E0)); -#17125=VERTEX_POINT('',#17124); -#17126=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.75E0)); -#17127=VERTEX_POINT('',#17126); -#17128=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.75E0)); -#17129=CARTESIAN_POINT('',(6.9E0,-3.E-1,6.75E0)); -#17130=VERTEX_POINT('',#17128); -#17131=VERTEX_POINT('',#17129); -#17132=CARTESIAN_POINT('',(6.9E0,-3.E-1,7.45E0)); -#17133=VERTEX_POINT('',#17132); -#17134=CARTESIAN_POINT('',(7.5E0,-3.E-1,7.45E0)); -#17135=VERTEX_POINT('',#17134); -#17136=CARTESIAN_POINT('',(-6.5E0,3.E-1,7.45E0)); -#17137=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.45E0)); -#17138=VERTEX_POINT('',#17136); -#17139=VERTEX_POINT('',#17137); -#17140=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.75E0)); -#17141=VERTEX_POINT('',#17140); -#17142=CARTESIAN_POINT('',(-6.5E0,3.E-1,6.75E0)); -#17143=VERTEX_POINT('',#17142); -#17144=CARTESIAN_POINT('',(7.5E0,3.E-1,6.75E0)); -#17145=CARTESIAN_POINT('',(6.9E0,3.E-1,6.75E0)); -#17146=VERTEX_POINT('',#17144); -#17147=VERTEX_POINT('',#17145); -#17148=CARTESIAN_POINT('',(6.9E0,3.E-1,7.45E0)); -#17149=VERTEX_POINT('',#17148); -#17150=CARTESIAN_POINT('',(7.5E0,3.E-1,7.45E0)); -#17151=VERTEX_POINT('',#17150); -#17152=CARTESIAN_POINT('',(-6.5E0,-3.E-1,6.35E0)); -#17153=CARTESIAN_POINT('',(-5.9E0,-3.E-1,6.35E0)); -#17154=VERTEX_POINT('',#17152); -#17155=VERTEX_POINT('',#17153); -#17156=CARTESIAN_POINT('',(-5.9E0,-3.E-1,5.65E0)); -#17157=VERTEX_POINT('',#17156); -#17158=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.65E0)); -#17159=VERTEX_POINT('',#17158); -#17160=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.65E0)); -#17161=CARTESIAN_POINT('',(6.9E0,-3.E-1,5.65E0)); -#17162=VERTEX_POINT('',#17160); -#17163=VERTEX_POINT('',#17161); -#17164=CARTESIAN_POINT('',(6.9E0,-3.E-1,6.35E0)); -#17165=VERTEX_POINT('',#17164); -#17166=CARTESIAN_POINT('',(7.5E0,-3.E-1,6.35E0)); -#17167=VERTEX_POINT('',#17166); -#17168=CARTESIAN_POINT('',(-6.5E0,3.E-1,6.35E0)); -#17169=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.35E0)); -#17170=VERTEX_POINT('',#17168); -#17171=VERTEX_POINT('',#17169); -#17172=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.65E0)); -#17173=VERTEX_POINT('',#17172); -#17174=CARTESIAN_POINT('',(-6.5E0,3.E-1,5.65E0)); -#17175=VERTEX_POINT('',#17174); -#17176=CARTESIAN_POINT('',(7.5E0,3.E-1,5.65E0)); -#17177=CARTESIAN_POINT('',(6.9E0,3.E-1,5.65E0)); -#17178=VERTEX_POINT('',#17176); -#17179=VERTEX_POINT('',#17177); -#17180=CARTESIAN_POINT('',(6.9E0,3.E-1,6.35E0)); -#17181=VERTEX_POINT('',#17180); -#17182=CARTESIAN_POINT('',(7.5E0,3.E-1,6.35E0)); -#17183=VERTEX_POINT('',#17182); -#17184=CARTESIAN_POINT('',(-6.5E0,-3.E-1,5.25E0)); -#17185=CARTESIAN_POINT('',(-5.9E0,-3.E-1,5.25E0)); -#17186=VERTEX_POINT('',#17184); -#17187=VERTEX_POINT('',#17185); -#17188=CARTESIAN_POINT('',(-5.9E0,-3.E-1,4.55E0)); -#17189=VERTEX_POINT('',#17188); -#17190=CARTESIAN_POINT('',(-6.5E0,-3.E-1,4.55E0)); -#17191=VERTEX_POINT('',#17190); -#17192=CARTESIAN_POINT('',(7.5E0,-3.E-1,4.55E0)); -#17193=CARTESIAN_POINT('',(6.9E0,-3.E-1,4.55E0)); -#17194=VERTEX_POINT('',#17192); -#17195=VERTEX_POINT('',#17193); -#17196=CARTESIAN_POINT('',(6.9E0,-3.E-1,5.25E0)); -#17197=VERTEX_POINT('',#17196); -#17198=CARTESIAN_POINT('',(7.5E0,-3.E-1,5.25E0)); -#17199=VERTEX_POINT('',#17198); -#17200=CARTESIAN_POINT('',(-6.5E0,3.E-1,5.25E0)); -#17201=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.25E0)); -#17202=VERTEX_POINT('',#17200); -#17203=VERTEX_POINT('',#17201); -#17204=CARTESIAN_POINT('',(-5.9E0,3.E-1,4.55E0)); -#17205=VERTEX_POINT('',#17204); -#17206=CARTESIAN_POINT('',(-6.5E0,3.E-1,4.55E0)); -#17207=VERTEX_POINT('',#17206); -#17208=CARTESIAN_POINT('',(7.5E0,3.E-1,4.55E0)); -#17209=CARTESIAN_POINT('',(6.9E0,3.E-1,4.55E0)); -#17210=VERTEX_POINT('',#17208); -#17211=VERTEX_POINT('',#17209); -#17212=CARTESIAN_POINT('',(6.9E0,3.E-1,5.25E0)); -#17213=VERTEX_POINT('',#17212); -#17214=CARTESIAN_POINT('',(7.5E0,3.E-1,5.25E0)); -#17215=VERTEX_POINT('',#17214); -#17216=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,4.55E0)); -#17217=CARTESIAN_POINT('',(-6.5E0,2.5E-1,4.55E0)); -#17218=VERTEX_POINT('',#17216); -#17219=VERTEX_POINT('',#17217); -#17220=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,5.25E0)); -#17221=CARTESIAN_POINT('',(-6.5E0,2.5E-1,5.25E0)); -#17222=VERTEX_POINT('',#17220); -#17223=VERTEX_POINT('',#17221); -#17224=CARTESIAN_POINT('',(7.5E0,-2.5E-1,4.55E0)); -#17225=CARTESIAN_POINT('',(7.5E0,2.5E-1,4.55E0)); -#17226=VERTEX_POINT('',#17224); -#17227=VERTEX_POINT('',#17225); -#17228=CARTESIAN_POINT('',(7.5E0,-2.5E-1,5.25E0)); -#17229=CARTESIAN_POINT('',(7.5E0,2.5E-1,5.25E0)); -#17230=VERTEX_POINT('',#17228); -#17231=VERTEX_POINT('',#17229); -#17232=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.25E0)); -#17233=VERTEX_POINT('',#17232); -#17234=CARTESIAN_POINT('',(-5.9E0,2.5E-1,5.25E0)); -#17235=VERTEX_POINT('',#17234); -#17236=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,4.55E0)); -#17237=VERTEX_POINT('',#17236); -#17238=CARTESIAN_POINT('',(-5.9E0,2.5E-1,4.55E0)); -#17239=VERTEX_POINT('',#17238); -#17240=CARTESIAN_POINT('',(6.9E0,-2.5E-1,4.55E0)); -#17241=VERTEX_POINT('',#17240); -#17242=CARTESIAN_POINT('',(6.9E0,2.5E-1,4.55E0)); -#17243=VERTEX_POINT('',#17242); -#17244=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.25E0)); -#17245=VERTEX_POINT('',#17244); -#17246=CARTESIAN_POINT('',(6.9E0,2.5E-1,5.25E0)); -#17247=VERTEX_POINT('',#17246); -#17248=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,5.65E0)); -#17249=CARTESIAN_POINT('',(-6.5E0,2.5E-1,5.65E0)); -#17250=VERTEX_POINT('',#17248); -#17251=VERTEX_POINT('',#17249); -#17252=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,6.35E0)); -#17253=CARTESIAN_POINT('',(-6.5E0,2.5E-1,6.35E0)); -#17254=VERTEX_POINT('',#17252); -#17255=VERTEX_POINT('',#17253); -#17256=CARTESIAN_POINT('',(7.5E0,-2.5E-1,5.65E0)); -#17257=CARTESIAN_POINT('',(7.5E0,2.5E-1,5.65E0)); -#17258=VERTEX_POINT('',#17256); -#17259=VERTEX_POINT('',#17257); -#17260=CARTESIAN_POINT('',(7.5E0,-2.5E-1,6.35E0)); -#17261=CARTESIAN_POINT('',(7.5E0,2.5E-1,6.35E0)); -#17262=VERTEX_POINT('',#17260); -#17263=VERTEX_POINT('',#17261); -#17264=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.35E0)); -#17265=VERTEX_POINT('',#17264); -#17266=CARTESIAN_POINT('',(-5.9E0,2.5E-1,6.35E0)); -#17267=VERTEX_POINT('',#17266); -#17268=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,5.65E0)); -#17269=VERTEX_POINT('',#17268); -#17270=CARTESIAN_POINT('',(-5.9E0,2.5E-1,5.65E0)); -#17271=VERTEX_POINT('',#17270); -#17272=CARTESIAN_POINT('',(6.9E0,-2.5E-1,5.65E0)); -#17273=VERTEX_POINT('',#17272); -#17274=CARTESIAN_POINT('',(6.9E0,2.5E-1,5.65E0)); -#17275=VERTEX_POINT('',#17274); -#17276=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.35E0)); -#17277=VERTEX_POINT('',#17276); -#17278=CARTESIAN_POINT('',(6.9E0,2.5E-1,6.35E0)); -#17279=VERTEX_POINT('',#17278); -#17280=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,6.75E0)); -#17281=CARTESIAN_POINT('',(-6.5E0,2.5E-1,6.75E0)); -#17282=VERTEX_POINT('',#17280); -#17283=VERTEX_POINT('',#17281); -#17284=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,7.45E0)); -#17285=CARTESIAN_POINT('',(-6.5E0,2.5E-1,7.45E0)); -#17286=VERTEX_POINT('',#17284); -#17287=VERTEX_POINT('',#17285); -#17288=CARTESIAN_POINT('',(7.5E0,-2.5E-1,6.75E0)); -#17289=CARTESIAN_POINT('',(7.5E0,2.5E-1,6.75E0)); -#17290=VERTEX_POINT('',#17288); -#17291=VERTEX_POINT('',#17289); -#17292=CARTESIAN_POINT('',(7.5E0,-2.5E-1,7.45E0)); -#17293=CARTESIAN_POINT('',(7.5E0,2.5E-1,7.45E0)); -#17294=VERTEX_POINT('',#17292); -#17295=VERTEX_POINT('',#17293); -#17296=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.45E0)); -#17297=VERTEX_POINT('',#17296); -#17298=CARTESIAN_POINT('',(-5.9E0,2.5E-1,7.45E0)); -#17299=VERTEX_POINT('',#17298); -#17300=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,6.75E0)); -#17301=VERTEX_POINT('',#17300); -#17302=CARTESIAN_POINT('',(-5.9E0,2.5E-1,6.75E0)); -#17303=VERTEX_POINT('',#17302); -#17304=CARTESIAN_POINT('',(6.9E0,-2.5E-1,6.75E0)); -#17305=VERTEX_POINT('',#17304); -#17306=CARTESIAN_POINT('',(6.9E0,2.5E-1,6.75E0)); -#17307=VERTEX_POINT('',#17306); -#17308=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.45E0)); -#17309=VERTEX_POINT('',#17308); -#17310=CARTESIAN_POINT('',(6.9E0,2.5E-1,7.45E0)); -#17311=VERTEX_POINT('',#17310); -#17312=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,7.85E0)); -#17313=CARTESIAN_POINT('',(-6.5E0,2.5E-1,7.85E0)); -#17314=VERTEX_POINT('',#17312); -#17315=VERTEX_POINT('',#17313); -#17316=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,8.55E0)); -#17317=CARTESIAN_POINT('',(-6.5E0,2.5E-1,8.55E0)); -#17318=VERTEX_POINT('',#17316); -#17319=VERTEX_POINT('',#17317); -#17320=CARTESIAN_POINT('',(7.5E0,-2.5E-1,7.85E0)); -#17321=CARTESIAN_POINT('',(7.5E0,2.5E-1,7.85E0)); -#17322=VERTEX_POINT('',#17320); -#17323=VERTEX_POINT('',#17321); -#17324=CARTESIAN_POINT('',(7.5E0,-2.5E-1,8.55E0)); -#17325=CARTESIAN_POINT('',(7.5E0,2.5E-1,8.55E0)); -#17326=VERTEX_POINT('',#17324); -#17327=VERTEX_POINT('',#17325); -#17328=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.55E0)); -#17329=VERTEX_POINT('',#17328); -#17330=CARTESIAN_POINT('',(-5.9E0,2.5E-1,8.55E0)); -#17331=VERTEX_POINT('',#17330); -#17332=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,7.85E0)); -#17333=VERTEX_POINT('',#17332); -#17334=CARTESIAN_POINT('',(-5.9E0,2.5E-1,7.85E0)); -#17335=VERTEX_POINT('',#17334); -#17336=CARTESIAN_POINT('',(6.9E0,-2.5E-1,7.85E0)); -#17337=VERTEX_POINT('',#17336); -#17338=CARTESIAN_POINT('',(6.9E0,2.5E-1,7.85E0)); -#17339=VERTEX_POINT('',#17338); -#17340=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.55E0)); -#17341=VERTEX_POINT('',#17340); -#17342=CARTESIAN_POINT('',(6.9E0,2.5E-1,8.55E0)); -#17343=VERTEX_POINT('',#17342); -#17344=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,8.95E0)); -#17345=CARTESIAN_POINT('',(-6.5E0,2.5E-1,8.95E0)); -#17346=VERTEX_POINT('',#17344); -#17347=VERTEX_POINT('',#17345); -#17348=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,9.65E0)); -#17349=CARTESIAN_POINT('',(-6.5E0,2.5E-1,9.65E0)); -#17350=VERTEX_POINT('',#17348); -#17351=VERTEX_POINT('',#17349); -#17352=CARTESIAN_POINT('',(7.5E0,-2.5E-1,8.95E0)); -#17353=CARTESIAN_POINT('',(7.5E0,2.5E-1,8.95E0)); -#17354=VERTEX_POINT('',#17352); -#17355=VERTEX_POINT('',#17353); -#17356=CARTESIAN_POINT('',(7.5E0,-2.5E-1,9.65E0)); -#17357=CARTESIAN_POINT('',(7.5E0,2.5E-1,9.65E0)); -#17358=VERTEX_POINT('',#17356); -#17359=VERTEX_POINT('',#17357); -#17360=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,9.65E0)); -#17361=VERTEX_POINT('',#17360); -#17362=CARTESIAN_POINT('',(-5.9E0,2.5E-1,9.65E0)); -#17363=VERTEX_POINT('',#17362); -#17364=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,8.95E0)); -#17365=VERTEX_POINT('',#17364); -#17366=CARTESIAN_POINT('',(-5.9E0,2.5E-1,8.95E0)); -#17367=VERTEX_POINT('',#17366); -#17368=CARTESIAN_POINT('',(6.9E0,-2.5E-1,8.95E0)); -#17369=VERTEX_POINT('',#17368); -#17370=CARTESIAN_POINT('',(6.9E0,2.5E-1,8.95E0)); -#17371=VERTEX_POINT('',#17370); -#17372=CARTESIAN_POINT('',(6.9E0,-2.5E-1,9.65E0)); -#17373=VERTEX_POINT('',#17372); -#17374=CARTESIAN_POINT('',(6.9E0,2.5E-1,9.65E0)); -#17375=VERTEX_POINT('',#17374); -#17376=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.005E1)); -#17377=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.005E1)); -#17378=VERTEX_POINT('',#17376); -#17379=VERTEX_POINT('',#17377); -#17380=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.075E1)); -#17381=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.075E1)); -#17382=VERTEX_POINT('',#17380); -#17383=VERTEX_POINT('',#17381); -#17384=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.005E1)); -#17385=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.005E1)); -#17386=VERTEX_POINT('',#17384); -#17387=VERTEX_POINT('',#17385); -#17388=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.075E1)); -#17389=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.075E1)); -#17390=VERTEX_POINT('',#17388); -#17391=VERTEX_POINT('',#17389); -#17392=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.075E1)); -#17393=VERTEX_POINT('',#17392); -#17394=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.075E1)); -#17395=VERTEX_POINT('',#17394); -#17396=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.005E1)); -#17397=VERTEX_POINT('',#17396); -#17398=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.005E1)); -#17399=VERTEX_POINT('',#17398); -#17400=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.005E1)); -#17401=VERTEX_POINT('',#17400); -#17402=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.005E1)); -#17403=VERTEX_POINT('',#17402); -#17404=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.075E1)); -#17405=VERTEX_POINT('',#17404); -#17406=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.075E1)); -#17407=VERTEX_POINT('',#17406); -#17408=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.115E1)); -#17409=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.115E1)); -#17410=VERTEX_POINT('',#17408); -#17411=VERTEX_POINT('',#17409); -#17412=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.185E1)); -#17413=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.185E1)); -#17414=VERTEX_POINT('',#17412); -#17415=VERTEX_POINT('',#17413); -#17416=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.115E1)); -#17417=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.115E1)); -#17418=VERTEX_POINT('',#17416); -#17419=VERTEX_POINT('',#17417); -#17420=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.185E1)); -#17421=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.185E1)); -#17422=VERTEX_POINT('',#17420); -#17423=VERTEX_POINT('',#17421); -#17424=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.185E1)); -#17425=VERTEX_POINT('',#17424); -#17426=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.185E1)); -#17427=VERTEX_POINT('',#17426); -#17428=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.115E1)); -#17429=VERTEX_POINT('',#17428); -#17430=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.115E1)); -#17431=VERTEX_POINT('',#17430); -#17432=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.115E1)); -#17433=VERTEX_POINT('',#17432); -#17434=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.115E1)); -#17435=VERTEX_POINT('',#17434); -#17436=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.185E1)); -#17437=VERTEX_POINT('',#17436); -#17438=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.185E1)); -#17439=VERTEX_POINT('',#17438); -#17440=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.225E1)); -#17441=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.225E1)); -#17442=VERTEX_POINT('',#17440); -#17443=VERTEX_POINT('',#17441); -#17444=CARTESIAN_POINT('',(-6.5E0,-2.5E-1,1.295E1)); -#17445=CARTESIAN_POINT('',(-6.5E0,2.5E-1,1.295E1)); -#17446=VERTEX_POINT('',#17444); -#17447=VERTEX_POINT('',#17445); -#17448=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.225E1)); -#17449=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.225E1)); -#17450=VERTEX_POINT('',#17448); -#17451=VERTEX_POINT('',#17449); -#17452=CARTESIAN_POINT('',(7.5E0,-2.5E-1,1.295E1)); -#17453=CARTESIAN_POINT('',(7.5E0,2.5E-1,1.295E1)); -#17454=VERTEX_POINT('',#17452); -#17455=VERTEX_POINT('',#17453); -#17456=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.295E1)); -#17457=VERTEX_POINT('',#17456); -#17458=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.295E1)); -#17459=VERTEX_POINT('',#17458); -#17460=CARTESIAN_POINT('',(-5.9E0,-2.5E-1,1.225E1)); -#17461=VERTEX_POINT('',#17460); -#17462=CARTESIAN_POINT('',(-5.9E0,2.5E-1,1.225E1)); -#17463=VERTEX_POINT('',#17462); -#17464=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.225E1)); -#17465=VERTEX_POINT('',#17464); -#17466=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.225E1)); -#17467=VERTEX_POINT('',#17466); -#17468=CARTESIAN_POINT('',(6.9E0,-2.5E-1,1.295E1)); -#17469=VERTEX_POINT('',#17468); -#17470=CARTESIAN_POINT('',(6.9E0,2.5E-1,1.295E1)); -#17471=VERTEX_POINT('',#17470); -#17472=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.397994897428E1)); -#17473=VERTEX_POINT('',#17472); -#17474=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.349005102572E1)); -#17475=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.287994897428E1)); -#17476=VERTEX_POINT('',#17474); -#17477=VERTEX_POINT('',#17475); -#17478=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.239005102572E1)); -#17479=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.177994897428E1)); -#17480=VERTEX_POINT('',#17478); -#17481=VERTEX_POINT('',#17479); -#17482=CARTESIAN_POINT('',(-7.5E0,3.E-1,-1.129005102572E1)); -#17483=VERTEX_POINT('',#17482); -#17484=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.4035E1)); -#17485=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.3435E1)); -#17486=VERTEX_POINT('',#17484); -#17487=VERTEX_POINT('',#17485); -#17488=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.2935E1)); -#17489=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.2335E1)); -#17490=VERTEX_POINT('',#17488); -#17491=VERTEX_POINT('',#17489); -#17492=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.1835E1)); -#17493=CARTESIAN_POINT('',(-7.15E0,-2.5E-1,-1.1235E1)); -#17494=VERTEX_POINT('',#17492); -#17495=VERTEX_POINT('',#17493); -#17496=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.4035E1)); -#17497=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.3435E1)); -#17498=VERTEX_POINT('',#17496); -#17499=VERTEX_POINT('',#17497); -#17500=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.3435E1)); -#17501=VERTEX_POINT('',#17500); -#17502=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.4035E1)); -#17503=VERTEX_POINT('',#17502); -#17504=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2935E1)); -#17505=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2335E1)); -#17506=VERTEX_POINT('',#17504); -#17507=VERTEX_POINT('',#17505); -#17508=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2335E1)); -#17509=VERTEX_POINT('',#17508); -#17510=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.2935E1)); -#17511=VERTEX_POINT('',#17510); -#17512=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1835E1)); -#17513=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1235E1)); -#17514=VERTEX_POINT('',#17512); -#17515=VERTEX_POINT('',#17513); -#17516=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1235E1)); -#17517=VERTEX_POINT('',#17516); -#17518=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.1835E1)); -#17519=VERTEX_POINT('',#17518); -#17520=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.1235E1)); -#17521=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.129005102572E1)); -#17522=VERTEX_POINT('',#17520); -#17523=VERTEX_POINT('',#17521); -#17524=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.177994897428E1)); -#17525=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.1835E1)); -#17526=VERTEX_POINT('',#17524); -#17527=VERTEX_POINT('',#17525); -#17528=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.2335E1)); -#17529=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.239005102572E1)); -#17530=VERTEX_POINT('',#17528); -#17531=VERTEX_POINT('',#17529); -#17532=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.287994897428E1)); -#17533=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.2935E1)); -#17534=VERTEX_POINT('',#17532); -#17535=VERTEX_POINT('',#17533); -#17536=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.3435E1)); -#17537=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.349005102572E1)); -#17538=VERTEX_POINT('',#17536); -#17539=VERTEX_POINT('',#17537); -#17540=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.397994897428E1)); -#17541=CARTESIAN_POINT('',(-7.5E0,-2.5E-1,-1.4035E1)); -#17542=VERTEX_POINT('',#17540); -#17543=VERTEX_POINT('',#17541); -#17544=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,8.126726183650E0)); -#17545=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,8.070385908836E0)); -#17546=VERTEX_POINT('',#17544); -#17547=VERTEX_POINT('',#17545); -#17548=CARTESIAN_POINT('',(7.659574747086E-1,1.5E0,7.985875536912E0)); -#17549=VERTEX_POINT('',#17548); -#17550=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,7.957705439802E0)); -#17551=VERTEX_POINT('',#17550); -#17552=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,7.957705439802E0)); -#17553=VERTEX_POINT('',#17552); -#17554=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,7.985875536912E0)); -#17555=VERTEX_POINT('',#17554); -#17556=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,8.070385908836E0)); -#17557=VERTEX_POINT('',#17556); -#17558=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,8.183066377870E0)); -#17559=VERTEX_POINT('',#17558); -#17560=CARTESIAN_POINT('',(0.E0,1.5E0,8.323917024608E0)); -#17561=VERTEX_POINT('',#17560); -#17562=CARTESIAN_POINT('',(0.E0,1.5E0,9.E0)); -#17563=VERTEX_POINT('',#17562); -#17564=CARTESIAN_POINT('',(2.E0,1.5E0,9.E0)); -#17565=VERTEX_POINT('',#17564); -#17566=CARTESIAN_POINT('',(2.E0,1.5E0,8.323917024608E0)); -#17567=VERTEX_POINT('',#17566); -#17568=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,8.183066377870E0)); -#17569=VERTEX_POINT('',#17568); -#17570=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,8.070385908836E0)); -#17571=VERTEX_POINT('',#17570); -#17572=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,7.985875536912E0)); -#17573=VERTEX_POINT('',#17572); -#17574=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,7.957705439802E0)); -#17575=VERTEX_POINT('',#17574); -#17576=CARTESIAN_POINT('',(1.319148957729E0,1.5E0,7.957705439802E0)); -#17577=VERTEX_POINT('',#17576); -#17578=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,7.985875536912E0)); -#17579=VERTEX_POINT('',#17578); -#17580=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,8.070385908836E0)); -#17581=VERTEX_POINT('',#17580); -#17582=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,8.830979256152E0)); -#17583=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,8.295746927498E0)); -#17584=VERTEX_POINT('',#17582); -#17585=VERTEX_POINT('',#17583); -#17586=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,8.211236555574E0)); -#17587=VERTEX_POINT('',#17586); -#17588=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,8.154896280760E0)); -#17589=VERTEX_POINT('',#17588); -#17590=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,8.126726183650E0)); -#17591=VERTEX_POINT('',#17590); -#17592=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,8.126726183650E0)); -#17593=VERTEX_POINT('',#17592); -#17594=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,8.154896280760E0)); -#17595=VERTEX_POINT('',#17594); -#17596=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,8.211236555574E0)); -#17597=VERTEX_POINT('',#17596); -#17598=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,8.295746927498E0)); -#17599=VERTEX_POINT('',#17598); -#17600=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,8.830979256152E0)); -#17601=VERTEX_POINT('',#17600); -#17602=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,8.126726183650E0)); -#17603=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,8.126726183650E0)); -#17604=VERTEX_POINT('',#17602); -#17605=VERTEX_POINT('',#17603); -#17606=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,8.154896280760E0)); -#17607=VERTEX_POINT('',#17606); -#17608=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,8.211236555574E0)); -#17609=VERTEX_POINT('',#17608); -#17610=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,8.295746927498E0)); -#17611=VERTEX_POINT('',#17610); -#17612=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,8.830979256152E0)); -#17613=VERTEX_POINT('',#17612); -#17614=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,8.830979256152E0)); -#17615=VERTEX_POINT('',#17614); -#17616=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,8.295746927498E0)); -#17617=VERTEX_POINT('',#17616); -#17618=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,8.211236555574E0)); -#17619=VERTEX_POINT('',#17618); -#17620=CARTESIAN_POINT('',(1.234042525291E0,1.5E0,8.154896280760E0)); -#17621=VERTEX_POINT('',#17620); -#17622=CARTESIAN_POINT('',(0.E0,1.5E0,6.661879763833E0)); -#17623=CARTESIAN_POINT('',(0.E0,1.5E0,7.732344421140E0)); -#17624=VERTEX_POINT('',#17622); -#17625=VERTEX_POINT('',#17623); -#17626=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.732344421140E0)); -#17627=VERTEX_POINT('',#17626); -#17628=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.281622383815E0)); -#17629=VERTEX_POINT('',#17628); -#17630=CARTESIAN_POINT('',(2.E0,1.5E0,7.281622383815E0)); -#17631=VERTEX_POINT('',#17630); -#17632=CARTESIAN_POINT('',(2.E0,1.5E0,7.112601639967E0)); -#17633=VERTEX_POINT('',#17632); -#17634=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,7.112601639967E0)); -#17635=VERTEX_POINT('',#17634); -#17636=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,6.661879763833E0)); -#17637=VERTEX_POINT('',#17636); -#17638=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,6.211157726508E0)); -#17639=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,6.267498081918E0)); -#17640=VERTEX_POINT('',#17638); -#17641=VERTEX_POINT('',#17639); -#17642=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,6.380178470356E0)); -#17643=VERTEX_POINT('',#17642); -#17644=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,6.436518664575E0)); -#17645=VERTEX_POINT('',#17644); -#17646=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,6.436518664575E0)); -#17647=VERTEX_POINT('',#17646); -#17648=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,6.380178470356E0)); -#17649=VERTEX_POINT('',#17648); -#17650=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,6.295668098432E0)); -#17651=VERTEX_POINT('',#17650); -#17652=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,6.154817371098E0)); -#17653=VERTEX_POINT('',#17652); -#17654=CARTESIAN_POINT('',(2.E0,1.5E0,6.013966966146E0)); -#17655=VERTEX_POINT('',#17654); -#17656=CARTESIAN_POINT('',(2.E0,1.5E0,5.844946222298E0)); -#17657=VERTEX_POINT('',#17656); -#17658=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,5.704095494964E0)); -#17659=VERTEX_POINT('',#17658); -#17660=CARTESIAN_POINT('',(1.829787239432E0,1.5E0,5.563244767630E0)); -#17661=VERTEX_POINT('',#17660); -#17662=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,5.478734395706E0)); -#17663=VERTEX_POINT('',#17662); -#17664=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,5.422394362678E0)); -#17665=VERTEX_POINT('',#17664); -#17666=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,5.422394362678E0)); -#17667=VERTEX_POINT('',#17666); -#17668=CARTESIAN_POINT('',(1.148936152458E0,1.5E0,5.478734395706E0)); -#17669=VERTEX_POINT('',#17668); -#17670=CARTESIAN_POINT('',(1.021276593208E0,1.5E0,5.591415106526E0)); -#17671=VERTEX_POINT('',#17670); -#17672=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,5.647755139554E0)); -#17673=VERTEX_POINT('',#17672); -#17674=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,5.591415106526E0)); -#17675=VERTEX_POINT('',#17674); -#17676=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,5.506904734602E0)); -#17677=VERTEX_POINT('',#17676); -#17678=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,5.450564379192E0)); -#17679=VERTEX_POINT('',#17678); -#17680=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,5.450564379192E0)); -#17681=VERTEX_POINT('',#17680); -#17682=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,5.506904734602E0)); -#17683=VERTEX_POINT('',#17682); -#17684=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,5.591415106526E0)); -#17685=VERTEX_POINT('',#17684); -#17686=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,5.732265511478E0)); -#17687=VERTEX_POINT('',#17686); -#17688=CARTESIAN_POINT('',(0.E0,1.5E0,5.873116238812E0)); -#17689=VERTEX_POINT('',#17688); -#17690=CARTESIAN_POINT('',(0.E0,1.5E0,5.985796627250E0)); -#17691=VERTEX_POINT('',#17690); -#17692=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,6.126647354584E0)); -#17693=VERTEX_POINT('',#17692); -#17694=CARTESIAN_POINT('',(1.702127456665E-1,1.5E0,6.267498081918E0)); -#17695=VERTEX_POINT('',#17694); -#17696=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,6.352008292651E0)); -#17697=VERTEX_POINT('',#17696); -#17698=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,6.408348648061E0)); -#17699=VERTEX_POINT('',#17698); -#17700=CARTESIAN_POINT('',(6.382979154587E-1,1.5E0,6.408348648061E0)); -#17701=VERTEX_POINT('',#17700); -#17702=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,6.352008292651E0)); -#17703=VERTEX_POINT('',#17702); -#17704=CARTESIAN_POINT('',(9.361702203751E-1,1.5E0,6.267498081918E0)); -#17705=VERTEX_POINT('',#17704); -#17706=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.985796627250E0)); -#17707=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,6.098477338070E0)); -#17708=VERTEX_POINT('',#17706); -#17709=VERTEX_POINT('',#17707); -#17710=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,6.211157726508E0)); -#17711=VERTEX_POINT('',#17710); -#17712=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,6.295668098432E0)); -#17713=VERTEX_POINT('',#17712); -#17714=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,6.295668098432E0)); -#17715=VERTEX_POINT('',#17714); -#17716=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,6.211157726508E0)); -#17717=VERTEX_POINT('',#17716); -#17718=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,6.098477338070E0)); -#17719=VERTEX_POINT('',#17718); -#17720=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,5.985796627250E0)); -#17721=VERTEX_POINT('',#17720); -#17722=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,5.873116238812E0)); -#17723=VERTEX_POINT('',#17722); -#17724=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,5.760435850374E0)); -#17725=VERTEX_POINT('',#17724); -#17726=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,5.647755139554E0)); -#17727=VERTEX_POINT('',#17726); -#17728=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,5.563244767630E0)); -#17729=VERTEX_POINT('',#17728); -#17730=CARTESIAN_POINT('',(1.489361703396E0,1.5E0,5.563244767630E0)); -#17731=VERTEX_POINT('',#17730); -#17732=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,5.647755139554E0)); -#17733=VERTEX_POINT('',#17732); -#17734=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,5.760435850374E0)); -#17735=VERTEX_POINT('',#17734); -#17736=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.873116238812E0)); -#17737=VERTEX_POINT('',#17736); -#17738=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,5.873116238812E0)); -#17739=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,5.760435850374E0)); -#17740=VERTEX_POINT('',#17738); -#17741=VERTEX_POINT('',#17739); -#17742=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,5.647755139554E0)); -#17743=VERTEX_POINT('',#17742); -#17744=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,5.591415106526E0)); -#17745=VERTEX_POINT('',#17744); -#17746=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,5.591415106526E0)); -#17747=VERTEX_POINT('',#17746); -#17748=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,5.647755139554E0)); -#17749=VERTEX_POINT('',#17748); -#17750=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,5.760435850374E0)); -#17751=VERTEX_POINT('',#17750); -#17752=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,5.873116238812E0)); -#17753=VERTEX_POINT('',#17752); -#17754=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,5.985796627250E0)); -#17755=VERTEX_POINT('',#17754); -#17756=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,6.098477338070E0)); -#17757=VERTEX_POINT('',#17756); -#17758=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,6.211157726508E0)); -#17759=VERTEX_POINT('',#17758); -#17760=CARTESIAN_POINT('',(5.957447290421E-1,1.5E0,6.267498081918E0)); -#17761=VERTEX_POINT('',#17760); -#17762=CARTESIAN_POINT('',(5.106383562088E-1,1.5E0,6.267498081918E0)); -#17763=VERTEX_POINT('',#17762); -#17764=CARTESIAN_POINT('',(3.829786777496E-1,1.5E0,6.211157726508E0)); -#17765=VERTEX_POINT('',#17764); -#17766=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,6.098477338070E0)); -#17767=VERTEX_POINT('',#17766); -#17768=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,5.985796627250E0)); -#17769=VERTEX_POINT('',#17768); -#17770=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.267419172256E0)); -#17771=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,4.211078816846E0)); -#17772=VERTEX_POINT('',#17770); -#17773=VERTEX_POINT('',#17771); -#17774=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,4.182908800332E0)); -#17775=VERTEX_POINT('',#17774); -#17776=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,4.182908800332E0)); -#17777=VERTEX_POINT('',#17776); -#17778=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,4.211078816846E0)); -#17779=VERTEX_POINT('',#17778); -#17780=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.267419172256E0)); -#17781=VERTEX_POINT('',#17780); -#17782=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,4.408269899590E0)); -#17783=VERTEX_POINT('',#17782); -#17784=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,4.295589188770E0)); -#17785=VERTEX_POINT('',#17784); -#17786=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,4.239249155742E0)); -#17787=VERTEX_POINT('',#17786); -#17788=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,4.211078816846E0)); -#17789=VERTEX_POINT('',#17788); -#17790=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,4.211078816846E0)); -#17791=VERTEX_POINT('',#17790); -#17792=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,4.239249155742E0)); -#17793=VERTEX_POINT('',#17792); -#17794=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,4.351929544180E0)); -#17795=VERTEX_POINT('',#17794); -#17796=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,4.464609932618E0)); -#17797=VERTEX_POINT('',#17796); -#17798=CARTESIAN_POINT('',(0.E0,1.5E0,4.661801015362E0)); -#17799=VERTEX_POINT('',#17798); -#17800=CARTESIAN_POINT('',(0.E0,1.5E0,4.718141048390E0)); -#17801=VERTEX_POINT('',#17800); -#17802=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,4.915332131134E0)); -#17803=VERTEX_POINT('',#17802); -#17804=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,5.028012519572E0)); -#17805=VERTEX_POINT('',#17804); -#17806=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,5.140692908010E0)); -#17807=VERTEX_POINT('',#17806); -#17808=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,5.168863246906E0)); -#17809=VERTEX_POINT('',#17808); -#17810=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,5.028012519572E0)); -#17811=VERTEX_POINT('',#17810); -#17812=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,4.971672164162E0)); -#17813=VERTEX_POINT('',#17812); -#17814=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,4.887161792238E0)); -#17815=VERTEX_POINT('',#17814); -#17816=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,4.746311387286E0)); -#17817=VERTEX_POINT('',#17816); -#17818=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,4.633630676466E0)); -#17819=VERTEX_POINT('',#17818); -#17820=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,4.492780271514E0)); -#17821=VERTEX_POINT('',#17820); -#17822=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,4.408269899590E0)); -#17823=VERTEX_POINT('',#17822); -#17824=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,4.351929544180E0)); -#17825=VERTEX_POINT('',#17824); -#17826=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,4.351929544180E0)); -#17827=VERTEX_POINT('',#17826); -#17828=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,4.408269899590E0)); -#17829=VERTEX_POINT('',#17828); -#17830=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,4.464609932618E0)); -#17831=VERTEX_POINT('',#17830); -#17832=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,4.633630676466E0)); -#17833=VERTEX_POINT('',#17832); -#17834=CARTESIAN_POINT('',(8.936170339584E-1,1.5E0,4.746311387286E0)); -#17835=VERTEX_POINT('',#17834); -#17836=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.746311387286E0)); -#17837=VERTEX_POINT('',#17836); -#17838=CARTESIAN_POINT('',(1.063829779625E0,1.5E0,4.633630676466E0)); -#17839=VERTEX_POINT('',#17838); -#17840=CARTESIAN_POINT('',(1.106382966042E0,1.5E0,4.464609932618E0)); -#17841=VERTEX_POINT('',#17840); -#17842=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,4.380099560694E0)); -#17843=VERTEX_POINT('',#17842); -#17844=CARTESIAN_POINT('',(1.361702144146E0,1.5E0,4.323759527666E0)); -#17845=VERTEX_POINT('',#17844); -#17846=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,4.323759527666E0)); -#17847=VERTEX_POINT('',#17846); -#17848=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,4.351929544180E0)); -#17849=VERTEX_POINT('',#17848); -#17850=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,4.408269899590E0)); -#17851=VERTEX_POINT('',#17850); -#17852=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,4.464609932618E0)); -#17853=VERTEX_POINT('',#17852); -#17854=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.605460659952E0)); -#17855=VERTEX_POINT('',#17854); -#17856=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,4.774481403800E0)); -#17857=VERTEX_POINT('',#17856); -#17858=CARTESIAN_POINT('',(1.744680851698E0,1.5E0,4.915332131134E0)); -#17859=VERTEX_POINT('',#17858); -#17860=CARTESIAN_POINT('',(1.702127665281E0,1.5E0,4.971672164162E0)); -#17861=VERTEX_POINT('',#17860); -#17862=CARTESIAN_POINT('',(1.617021262646E0,1.5E0,5.028012519572E0)); -#17863=VERTEX_POINT('',#17862); -#17864=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,5.056182536086E0)); -#17865=VERTEX_POINT('',#17864); -#17866=CARTESIAN_POINT('',(1.531914889812E0,1.5E0,5.197033263420E0)); -#17867=VERTEX_POINT('',#17866); -#17868=CARTESIAN_POINT('',(1.659574478865E0,1.5E0,5.168863246906E0)); -#17869=VERTEX_POINT('',#17868); -#17870=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,5.112522891496E0)); -#17871=VERTEX_POINT('',#17870); -#17872=CARTESIAN_POINT('',(1.872340425849E0,1.5E0,5.028012519572E0)); -#17873=VERTEX_POINT('',#17872); -#17874=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,4.915332131134E0)); -#17875=VERTEX_POINT('',#17874); -#17876=CARTESIAN_POINT('',(2.E0,1.5E0,4.802651420314E0)); -#17877=VERTEX_POINT('',#17876); -#17878=CARTESIAN_POINT('',(2.E0,1.5E0,4.577290643438E0)); -#17879=VERTEX_POINT('',#17878); -#17880=CARTESIAN_POINT('',(1.957446809858E0,1.5E0,4.464609932618E0)); -#17881=VERTEX_POINT('',#17880); -#17882=CARTESIAN_POINT('',(1.872340425849E0,1.5E0,4.351929544180E0)); -#17883=VERTEX_POINT('',#17882); -#17884=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,3.957547701074E0)); -#17885=CARTESIAN_POINT('',(2.E0,1.5E0,3.957547701074E0)); -#17886=VERTEX_POINT('',#17884); -#17887=VERTEX_POINT('',#17885); -#17888=CARTESIAN_POINT('',(2.E0,1.5E0,2.943423560368E0)); -#17889=VERTEX_POINT('',#17888); -#17890=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,2.943423560368E0)); -#17891=VERTEX_POINT('',#17890); -#17892=CARTESIAN_POINT('',(1.787234038115E0,1.5E0,3.732186924198E0)); -#17893=VERTEX_POINT('',#17892); -#17894=CARTESIAN_POINT('',(8.510638475418E-1,1.5E0,3.027933932292E0)); -#17895=VERTEX_POINT('',#17894); -#17896=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,2.971593254501E0)); -#17897=VERTEX_POINT('',#17896); -#17898=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,2.943423560368E0)); -#17899=VERTEX_POINT('',#17898); -#17900=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,2.943423560368E0)); -#17901=VERTEX_POINT('',#17900); -#17902=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,2.971593254501E0)); -#17903=VERTEX_POINT('',#17902); -#17904=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,3.084273965320E0)); -#17905=VERTEX_POINT('',#17904); -#17906=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,3.196954676140E0)); -#17907=VERTEX_POINT('',#17906); -#17908=CARTESIAN_POINT('',(0.E0,1.5E0,3.365975419988E0)); -#17909=VERTEX_POINT('',#17908); -#17910=CARTESIAN_POINT('',(0.E0,1.5E0,3.478655486044E0)); -#17911=VERTEX_POINT('',#17910); -#17912=CARTESIAN_POINT('',(4.255318641663E-2,1.5E0,3.675846568788E0)); -#17913=VERTEX_POINT('',#17912); -#17914=CARTESIAN_POINT('',(1.276595592499E-1,1.5E0,3.788526957226E0)); -#17915=VERTEX_POINT('',#17914); -#17916=CARTESIAN_POINT('',(2.978723049164E-1,1.5E0,3.901207668046E0)); -#17917=VERTEX_POINT('',#17916); -#17918=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.929377684560E0)); -#17919=VERTEX_POINT('',#17918); -#17920=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.788526957226E0)); -#17921=VERTEX_POINT('',#17920); -#17922=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,3.732186924198E0)); -#17923=VERTEX_POINT('',#17922); -#17924=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,3.647676552274E0)); -#17925=VERTEX_POINT('',#17924); -#17926=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,3.506825824940E0)); -#17927=VERTEX_POINT('',#17926); -#17928=CARTESIAN_POINT('',(2.127659320831E-1,1.5E0,3.394145114120E0)); -#17929=VERTEX_POINT('',#17928); -#17930=CARTESIAN_POINT('',(2.553191184998E-1,1.5E0,3.253294709168E0)); -#17931=VERTEX_POINT('',#17930); -#17932=CARTESIAN_POINT('',(3.404254913330E-1,1.5E0,3.168784337244E0)); -#17933=VERTEX_POINT('',#17932); -#17934=CARTESIAN_POINT('',(4.680850505829E-1,1.5E0,3.112444304216E0)); -#17935=VERTEX_POINT('',#17934); -#17936=CARTESIAN_POINT('',(5.531915426254E-1,1.5E0,3.112444304216E0)); -#17937=VERTEX_POINT('',#17936); -#17938=CARTESIAN_POINT('',(7.234042882919E-1,1.5E0,3.168784337244E0)); -#17939=VERTEX_POINT('',#17938); -#17940=CARTESIAN_POINT('',(2.E0,1.5E0,1.760278353432E0)); -#17941=CARTESIAN_POINT('',(2.E0,1.5E0,1.591257609584E0)); -#17942=VERTEX_POINT('',#17940); -#17943=VERTEX_POINT('',#17941); -#17944=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,2.070149502232E0)); -#17945=VERTEX_POINT('',#17944); -#17946=CARTESIAN_POINT('',(0.E0,1.5E0,1.591257609584E0)); -#17947=VERTEX_POINT('',#17946); -#17948=CARTESIAN_POINT('',(0.E0,1.5E0,1.760278353432E0)); -#17949=VERTEX_POINT('',#17948); -#17950=CARTESIAN_POINT('',(8.085106611252E-1,1.5E0,2.154659874156E0)); -#17951=VERTEX_POINT('',#17950); -#17952=CARTESIAN_POINT('',(0.E0,1.5E0,2.549041394881E0)); -#17953=VERTEX_POINT('',#17952); -#17954=CARTESIAN_POINT('',(0.E0,1.5E0,2.718062138729E0)); -#17955=VERTEX_POINT('',#17954); -#17956=CARTESIAN_POINT('',(9.787234067917E-1,1.5E0,2.239170246080E0)); -#17957=VERTEX_POINT('',#17956); -#17958=CARTESIAN_POINT('',(2.E0,1.5E0,2.718062138729E0)); -#17959=VERTEX_POINT('',#17958); -#17960=CARTESIAN_POINT('',(2.E0,1.5E0,2.549041394881E0)); -#17961=VERTEX_POINT('',#17960); -#17962=CARTESIAN_POINT('',(1.191489338875E0,1.5E0,2.154659874156E0)); -#17963=VERTEX_POINT('',#17962); -#17964=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,8.126726183650E0)); -#17965=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,8.070385908836E0)); -#17966=VERTEX_POINT('',#17964); -#17967=VERTEX_POINT('',#17965); -#17968=CARTESIAN_POINT('',(7.659574747086E-1,1.55E0,7.985875536912E0)); -#17969=VERTEX_POINT('',#17968); -#17970=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,7.957705439802E0)); -#17971=VERTEX_POINT('',#17970); -#17972=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,7.957705439802E0)); -#17973=VERTEX_POINT('',#17972); -#17974=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,7.985875536912E0)); -#17975=VERTEX_POINT('',#17974); -#17976=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,8.070385908836E0)); -#17977=VERTEX_POINT('',#17976); -#17978=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,8.183066377870E0)); -#17979=VERTEX_POINT('',#17978); -#17980=CARTESIAN_POINT('',(0.E0,1.55E0,8.323917024608E0)); -#17981=VERTEX_POINT('',#17980); -#17982=CARTESIAN_POINT('',(0.E0,1.55E0,9.E0)); -#17983=VERTEX_POINT('',#17982); -#17984=CARTESIAN_POINT('',(2.E0,1.55E0,9.E0)); -#17985=VERTEX_POINT('',#17984); -#17986=CARTESIAN_POINT('',(2.E0,1.55E0,8.323917024608E0)); -#17987=VERTEX_POINT('',#17986); -#17988=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,8.183066377870E0)); -#17989=VERTEX_POINT('',#17988); -#17990=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,8.070385908836E0)); -#17991=VERTEX_POINT('',#17990); -#17992=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,7.985875536912E0)); -#17993=VERTEX_POINT('',#17992); -#17994=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,7.957705439802E0)); -#17995=VERTEX_POINT('',#17994); -#17996=CARTESIAN_POINT('',(1.319148957729E0,1.55E0,7.957705439802E0)); -#17997=VERTEX_POINT('',#17996); -#17998=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,7.985875536912E0)); -#17999=VERTEX_POINT('',#17998); -#18000=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,8.070385908836E0)); -#18001=VERTEX_POINT('',#18000); -#18002=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.830979256152E0)); -#18003=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.295746927498E0)); -#18004=VERTEX_POINT('',#18002); -#18005=VERTEX_POINT('',#18003); -#18006=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,8.211236555574E0)); -#18007=VERTEX_POINT('',#18006); -#18008=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,8.154896280760E0)); -#18009=VERTEX_POINT('',#18008); -#18010=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,8.126726183650E0)); -#18011=VERTEX_POINT('',#18010); -#18012=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,8.126726183650E0)); -#18013=VERTEX_POINT('',#18012); -#18014=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,8.154896280760E0)); -#18015=VERTEX_POINT('',#18014); -#18016=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,8.211236555574E0)); -#18017=VERTEX_POINT('',#18016); -#18018=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.295746927498E0)); -#18019=VERTEX_POINT('',#18018); -#18020=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.830979256152E0)); -#18021=VERTEX_POINT('',#18020); -#18022=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,8.126726183650E0)); -#18023=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,8.126726183650E0)); -#18024=VERTEX_POINT('',#18022); -#18025=VERTEX_POINT('',#18023); -#18026=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,8.154896280760E0)); -#18027=VERTEX_POINT('',#18026); -#18028=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,8.211236555574E0)); -#18029=VERTEX_POINT('',#18028); -#18030=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.295746927498E0)); -#18031=VERTEX_POINT('',#18030); -#18032=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.830979256152E0)); -#18033=VERTEX_POINT('',#18032); -#18034=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.830979256152E0)); -#18035=VERTEX_POINT('',#18034); -#18036=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.295746927498E0)); -#18037=VERTEX_POINT('',#18036); -#18038=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,8.211236555574E0)); -#18039=VERTEX_POINT('',#18038); -#18040=CARTESIAN_POINT('',(1.234042525291E0,1.55E0,8.154896280760E0)); -#18041=VERTEX_POINT('',#18040); -#18042=CARTESIAN_POINT('',(0.E0,1.55E0,6.661879763833E0)); -#18043=CARTESIAN_POINT('',(0.E0,1.55E0,7.732344421140E0)); -#18044=VERTEX_POINT('',#18042); -#18045=VERTEX_POINT('',#18043); -#18046=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.732344421140E0)); -#18047=VERTEX_POINT('',#18046); -#18048=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.281622383815E0)); -#18049=VERTEX_POINT('',#18048); -#18050=CARTESIAN_POINT('',(2.E0,1.55E0,7.281622383815E0)); -#18051=VERTEX_POINT('',#18050); -#18052=CARTESIAN_POINT('',(2.E0,1.55E0,7.112601639967E0)); -#18053=VERTEX_POINT('',#18052); -#18054=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.112601639967E0)); -#18055=VERTEX_POINT('',#18054); -#18056=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,6.661879763833E0)); -#18057=VERTEX_POINT('',#18056); -#18058=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,6.211157726508E0)); -#18059=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,6.267498081918E0)); -#18060=VERTEX_POINT('',#18058); -#18061=VERTEX_POINT('',#18059); -#18062=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,6.380178470356E0)); -#18063=VERTEX_POINT('',#18062); -#18064=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.436518664575E0)); -#18065=VERTEX_POINT('',#18064); -#18066=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.436518664575E0)); -#18067=VERTEX_POINT('',#18066); -#18068=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,6.380178470356E0)); -#18069=VERTEX_POINT('',#18068); -#18070=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,6.295668098432E0)); -#18071=VERTEX_POINT('',#18070); -#18072=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,6.154817371098E0)); -#18073=VERTEX_POINT('',#18072); -#18074=CARTESIAN_POINT('',(2.E0,1.55E0,6.013966966146E0)); -#18075=VERTEX_POINT('',#18074); -#18076=CARTESIAN_POINT('',(2.E0,1.55E0,5.844946222298E0)); -#18077=VERTEX_POINT('',#18076); -#18078=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,5.704095494964E0)); -#18079=VERTEX_POINT('',#18078); -#18080=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,5.563244767630E0)); -#18081=VERTEX_POINT('',#18080); -#18082=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,5.478734395706E0)); -#18083=VERTEX_POINT('',#18082); -#18084=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.422394362678E0)); -#18085=VERTEX_POINT('',#18084); -#18086=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.422394362678E0)); -#18087=VERTEX_POINT('',#18086); -#18088=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,5.478734395706E0)); -#18089=VERTEX_POINT('',#18088); -#18090=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,5.591415106526E0)); -#18091=VERTEX_POINT('',#18090); -#18092=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,5.647755139554E0)); -#18093=VERTEX_POINT('',#18092); -#18094=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,5.591415106526E0)); -#18095=VERTEX_POINT('',#18094); -#18096=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,5.506904734602E0)); -#18097=VERTEX_POINT('',#18096); -#18098=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,5.450564379192E0)); -#18099=VERTEX_POINT('',#18098); -#18100=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.450564379192E0)); -#18101=VERTEX_POINT('',#18100); -#18102=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.506904734602E0)); -#18103=VERTEX_POINT('',#18102); -#18104=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,5.591415106526E0)); -#18105=VERTEX_POINT('',#18104); -#18106=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,5.732265511478E0)); -#18107=VERTEX_POINT('',#18106); -#18108=CARTESIAN_POINT('',(0.E0,1.55E0,5.873116238812E0)); -#18109=VERTEX_POINT('',#18108); -#18110=CARTESIAN_POINT('',(0.E0,1.55E0,5.985796627250E0)); -#18111=VERTEX_POINT('',#18110); -#18112=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,6.126647354584E0)); -#18113=VERTEX_POINT('',#18112); -#18114=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,6.267498081918E0)); -#18115=VERTEX_POINT('',#18114); -#18116=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,6.352008292651E0)); -#18117=VERTEX_POINT('',#18116); -#18118=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.408348648061E0)); -#18119=VERTEX_POINT('',#18118); -#18120=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,6.408348648061E0)); -#18121=VERTEX_POINT('',#18120); -#18122=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,6.352008292651E0)); -#18123=VERTEX_POINT('',#18122); -#18124=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,6.267498081918E0)); -#18125=VERTEX_POINT('',#18124); -#18126=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.985796627250E0)); -#18127=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,6.098477338070E0)); -#18128=VERTEX_POINT('',#18126); -#18129=VERTEX_POINT('',#18127); -#18130=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,6.211157726508E0)); -#18131=VERTEX_POINT('',#18130); -#18132=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.295668098432E0)); -#18133=VERTEX_POINT('',#18132); -#18134=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.295668098432E0)); -#18135=VERTEX_POINT('',#18134); -#18136=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,6.211157726508E0)); -#18137=VERTEX_POINT('',#18136); -#18138=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,6.098477338070E0)); -#18139=VERTEX_POINT('',#18138); -#18140=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.985796627250E0)); -#18141=VERTEX_POINT('',#18140); -#18142=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.873116238812E0)); -#18143=VERTEX_POINT('',#18142); -#18144=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,5.760435850374E0)); -#18145=VERTEX_POINT('',#18144); -#18146=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,5.647755139554E0)); -#18147=VERTEX_POINT('',#18146); -#18148=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.563244767630E0)); -#18149=VERTEX_POINT('',#18148); -#18150=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.563244767630E0)); -#18151=VERTEX_POINT('',#18150); -#18152=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.647755139554E0)); -#18153=VERTEX_POINT('',#18152); -#18154=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,5.760435850374E0)); -#18155=VERTEX_POINT('',#18154); -#18156=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.873116238812E0)); -#18157=VERTEX_POINT('',#18156); -#18158=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.873116238812E0)); -#18159=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,5.760435850374E0)); -#18160=VERTEX_POINT('',#18158); -#18161=VERTEX_POINT('',#18159); -#18162=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,5.647755139554E0)); -#18163=VERTEX_POINT('',#18162); -#18164=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.591415106526E0)); -#18165=VERTEX_POINT('',#18164); -#18166=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,5.591415106526E0)); -#18167=VERTEX_POINT('',#18166); -#18168=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,5.647755139554E0)); -#18169=VERTEX_POINT('',#18168); -#18170=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,5.760435850374E0)); -#18171=VERTEX_POINT('',#18170); -#18172=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.873116238812E0)); -#18173=VERTEX_POINT('',#18172); -#18174=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.985796627250E0)); -#18175=VERTEX_POINT('',#18174); -#18176=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,6.098477338070E0)); -#18177=VERTEX_POINT('',#18176); -#18178=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,6.211157726508E0)); -#18179=VERTEX_POINT('',#18178); -#18180=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,6.267498081918E0)); -#18181=VERTEX_POINT('',#18180); -#18182=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.267498081918E0)); -#18183=VERTEX_POINT('',#18182); -#18184=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,6.211157726508E0)); -#18185=VERTEX_POINT('',#18184); -#18186=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,6.098477338070E0)); -#18187=VERTEX_POINT('',#18186); -#18188=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.985796627250E0)); -#18189=VERTEX_POINT('',#18188); -#18190=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.267419172256E0)); -#18191=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,4.211078816846E0)); -#18192=VERTEX_POINT('',#18190); -#18193=VERTEX_POINT('',#18191); -#18194=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.182908800332E0)); -#18195=VERTEX_POINT('',#18194); -#18196=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.182908800332E0)); -#18197=VERTEX_POINT('',#18196); -#18198=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.211078816846E0)); -#18199=VERTEX_POINT('',#18198); -#18200=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.267419172256E0)); -#18201=VERTEX_POINT('',#18200); -#18202=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,4.408269899590E0)); -#18203=VERTEX_POINT('',#18202); -#18204=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,4.295589188770E0)); -#18205=VERTEX_POINT('',#18204); -#18206=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.239249155742E0)); -#18207=VERTEX_POINT('',#18206); -#18208=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.211078816846E0)); -#18209=VERTEX_POINT('',#18208); -#18210=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.211078816846E0)); -#18211=VERTEX_POINT('',#18210); -#18212=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,4.239249155742E0)); -#18213=VERTEX_POINT('',#18212); -#18214=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,4.351929544180E0)); -#18215=VERTEX_POINT('',#18214); -#18216=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.464609932618E0)); -#18217=VERTEX_POINT('',#18216); -#18218=CARTESIAN_POINT('',(0.E0,1.55E0,4.661801015362E0)); -#18219=VERTEX_POINT('',#18218); -#18220=CARTESIAN_POINT('',(0.E0,1.55E0,4.718141048390E0)); -#18221=VERTEX_POINT('',#18220); -#18222=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.915332131134E0)); -#18223=VERTEX_POINT('',#18222); -#18224=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,5.028012519572E0)); -#18225=VERTEX_POINT('',#18224); -#18226=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.140692908010E0)); -#18227=VERTEX_POINT('',#18226); -#18228=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.168863246906E0)); -#18229=VERTEX_POINT('',#18228); -#18230=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.028012519572E0)); -#18231=VERTEX_POINT('',#18230); -#18232=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.971672164162E0)); -#18233=VERTEX_POINT('',#18232); -#18234=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.887161792238E0)); -#18235=VERTEX_POINT('',#18234); -#18236=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.746311387286E0)); -#18237=VERTEX_POINT('',#18236); -#18238=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.633630676466E0)); -#18239=VERTEX_POINT('',#18238); -#18240=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.492780271514E0)); -#18241=VERTEX_POINT('',#18240); -#18242=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.408269899590E0)); -#18243=VERTEX_POINT('',#18242); -#18244=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.351929544180E0)); -#18245=VERTEX_POINT('',#18244); -#18246=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.351929544180E0)); -#18247=VERTEX_POINT('',#18246); -#18248=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.408269899590E0)); -#18249=VERTEX_POINT('',#18248); -#18250=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,4.464609932618E0)); -#18251=VERTEX_POINT('',#18250); -#18252=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.633630676466E0)); -#18253=VERTEX_POINT('',#18252); -#18254=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.746311387286E0)); -#18255=VERTEX_POINT('',#18254); -#18256=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.746311387286E0)); -#18257=VERTEX_POINT('',#18256); -#18258=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.633630676466E0)); -#18259=VERTEX_POINT('',#18258); -#18260=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,4.464609932618E0)); -#18261=VERTEX_POINT('',#18260); -#18262=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.380099560694E0)); -#18263=VERTEX_POINT('',#18262); -#18264=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.323759527666E0)); -#18265=VERTEX_POINT('',#18264); -#18266=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.323759527666E0)); -#18267=VERTEX_POINT('',#18266); -#18268=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,4.351929544180E0)); -#18269=VERTEX_POINT('',#18268); -#18270=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.408269899590E0)); -#18271=VERTEX_POINT('',#18270); -#18272=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.464609932618E0)); -#18273=VERTEX_POINT('',#18272); -#18274=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.605460659952E0)); -#18275=VERTEX_POINT('',#18274); -#18276=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.774481403800E0)); -#18277=VERTEX_POINT('',#18276); -#18278=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.915332131134E0)); -#18279=VERTEX_POINT('',#18278); -#18280=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.971672164162E0)); -#18281=VERTEX_POINT('',#18280); -#18282=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,5.028012519572E0)); -#18283=VERTEX_POINT('',#18282); -#18284=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.056182536086E0)); -#18285=VERTEX_POINT('',#18284); -#18286=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.197033263420E0)); -#18287=VERTEX_POINT('',#18286); -#18288=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.168863246906E0)); -#18289=VERTEX_POINT('',#18288); -#18290=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.112522891496E0)); -#18291=VERTEX_POINT('',#18290); -#18292=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,5.028012519572E0)); -#18293=VERTEX_POINT('',#18292); -#18294=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.915332131134E0)); -#18295=VERTEX_POINT('',#18294); -#18296=CARTESIAN_POINT('',(2.E0,1.55E0,4.802651420314E0)); -#18297=VERTEX_POINT('',#18296); -#18298=CARTESIAN_POINT('',(2.E0,1.55E0,4.577290643438E0)); -#18299=VERTEX_POINT('',#18298); -#18300=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.464609932618E0)); -#18301=VERTEX_POINT('',#18300); -#18302=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,4.351929544180E0)); -#18303=VERTEX_POINT('',#18302); -#18304=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.957547701074E0)); -#18305=CARTESIAN_POINT('',(2.E0,1.55E0,3.957547701074E0)); -#18306=VERTEX_POINT('',#18304); -#18307=VERTEX_POINT('',#18305); -#18308=CARTESIAN_POINT('',(2.E0,1.55E0,2.943423560368E0)); -#18309=VERTEX_POINT('',#18308); -#18310=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,2.943423560368E0)); -#18311=VERTEX_POINT('',#18310); -#18312=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.732186924198E0)); -#18313=VERTEX_POINT('',#18312); -#18314=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,3.027933932292E0)); -#18315=VERTEX_POINT('',#18314); -#18316=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,2.971593254501E0)); -#18317=VERTEX_POINT('',#18316); -#18318=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,2.943423560368E0)); -#18319=VERTEX_POINT('',#18318); -#18320=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,2.943423560368E0)); -#18321=VERTEX_POINT('',#18320); -#18322=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,2.971593254501E0)); -#18323=VERTEX_POINT('',#18322); -#18324=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.084273965320E0)); -#18325=VERTEX_POINT('',#18324); -#18326=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.196954676140E0)); -#18327=VERTEX_POINT('',#18326); -#18328=CARTESIAN_POINT('',(0.E0,1.55E0,3.365975419988E0)); -#18329=VERTEX_POINT('',#18328); -#18330=CARTESIAN_POINT('',(0.E0,1.55E0,3.478655486044E0)); -#18331=VERTEX_POINT('',#18330); -#18332=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.675846568788E0)); -#18333=VERTEX_POINT('',#18332); -#18334=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.788526957226E0)); -#18335=VERTEX_POINT('',#18334); -#18336=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,3.901207668046E0)); -#18337=VERTEX_POINT('',#18336); -#18338=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.929377684560E0)); -#18339=VERTEX_POINT('',#18338); -#18340=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.788526957226E0)); -#18341=VERTEX_POINT('',#18340); -#18342=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.732186924198E0)); -#18343=VERTEX_POINT('',#18342); -#18344=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.647676552274E0)); -#18345=VERTEX_POINT('',#18344); -#18346=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.506825824940E0)); -#18347=VERTEX_POINT('',#18346); -#18348=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.394145114120E0)); -#18349=VERTEX_POINT('',#18348); -#18350=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.253294709168E0)); -#18351=VERTEX_POINT('',#18350); -#18352=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.168784337244E0)); -#18353=VERTEX_POINT('',#18352); -#18354=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.112444304216E0)); -#18355=VERTEX_POINT('',#18354); -#18356=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,3.112444304216E0)); -#18357=VERTEX_POINT('',#18356); -#18358=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,3.168784337244E0)); -#18359=VERTEX_POINT('',#18358); -#18360=CARTESIAN_POINT('',(2.E0,1.55E0,1.760278353432E0)); -#18361=CARTESIAN_POINT('',(2.E0,1.55E0,1.591257609584E0)); -#18362=VERTEX_POINT('',#18360); -#18363=VERTEX_POINT('',#18361); -#18364=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.070149502232E0)); -#18365=VERTEX_POINT('',#18364); -#18366=CARTESIAN_POINT('',(0.E0,1.55E0,1.591257609584E0)); -#18367=VERTEX_POINT('',#18366); -#18368=CARTESIAN_POINT('',(0.E0,1.55E0,1.760278353432E0)); -#18369=VERTEX_POINT('',#18368); -#18370=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,2.154659874156E0)); -#18371=VERTEX_POINT('',#18370); -#18372=CARTESIAN_POINT('',(0.E0,1.55E0,2.549041394881E0)); -#18373=VERTEX_POINT('',#18372); -#18374=CARTESIAN_POINT('',(0.E0,1.55E0,2.718062138729E0)); -#18375=VERTEX_POINT('',#18374); -#18376=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.239170246080E0)); -#18377=VERTEX_POINT('',#18376); -#18378=CARTESIAN_POINT('',(2.E0,1.55E0,2.718062138729E0)); -#18379=VERTEX_POINT('',#18378); -#18380=CARTESIAN_POINT('',(2.E0,1.55E0,2.549041394881E0)); -#18381=VERTEX_POINT('',#18380); -#18382=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,2.154659874156E0)); -#18383=VERTEX_POINT('',#18382); -#18384=CARTESIAN_POINT('',(3.05E0,-2.5E-1,1.17E1)); -#18385=CARTESIAN_POINT('',(2.45E0,-2.5E-1,1.17E1)); -#18386=VERTEX_POINT('',#18384); -#18387=VERTEX_POINT('',#18385); -#18388=CARTESIAN_POINT('',(1.55E0,-2.5E-1,1.17E1)); -#18389=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,1.17E1)); -#18390=VERTEX_POINT('',#18388); -#18391=VERTEX_POINT('',#18389); -#18392=CARTESIAN_POINT('',(5.E-2,-2.5E-1,1.17E1)); -#18393=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,1.17E1)); -#18394=VERTEX_POINT('',#18392); -#18395=VERTEX_POINT('',#18393); -#18396=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,1.17E1)); -#18397=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,1.17E1)); -#18398=VERTEX_POINT('',#18396); -#18399=VERTEX_POINT('',#18397); -#18400=CARTESIAN_POINT('',(2.45E0,-3.E-1,1.17E1)); -#18401=CARTESIAN_POINT('',(3.05E0,-3.E-1,1.17E1)); -#18402=VERTEX_POINT('',#18400); -#18403=VERTEX_POINT('',#18401); -#18404=CARTESIAN_POINT('',(9.5E-1,-3.E-1,1.17E1)); -#18405=CARTESIAN_POINT('',(1.55E0,-3.E-1,1.17E1)); -#18406=VERTEX_POINT('',#18404); -#18407=VERTEX_POINT('',#18405); -#18408=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,1.17E1)); -#18409=CARTESIAN_POINT('',(5.E-2,-3.E-1,1.17E1)); -#18410=VERTEX_POINT('',#18408); -#18411=VERTEX_POINT('',#18409); -#18412=CARTESIAN_POINT('',(-2.05E0,-3.E-1,1.17E1)); -#18413=CARTESIAN_POINT('',(-1.45E0,-3.E-1,1.17E1)); -#18414=VERTEX_POINT('',#18412); -#18415=VERTEX_POINT('',#18413); -#18416=CARTESIAN_POINT('',(2.45E0,-2.5E-1,1.05E1)); -#18417=CARTESIAN_POINT('',(3.05E0,-2.5E-1,1.05E1)); -#18418=VERTEX_POINT('',#18416); -#18419=VERTEX_POINT('',#18417); -#18420=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,1.05E1)); -#18421=CARTESIAN_POINT('',(1.55E0,-2.5E-1,1.05E1)); -#18422=VERTEX_POINT('',#18420); -#18423=VERTEX_POINT('',#18421); -#18424=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,1.05E1)); -#18425=CARTESIAN_POINT('',(5.E-2,-2.5E-1,1.05E1)); -#18426=VERTEX_POINT('',#18424); -#18427=VERTEX_POINT('',#18425); -#18428=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,1.05E1)); -#18429=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,1.05E1)); -#18430=VERTEX_POINT('',#18428); -#18431=VERTEX_POINT('',#18429); -#18432=CARTESIAN_POINT('',(2.45E0,-3.E-1,1.05E1)); -#18433=CARTESIAN_POINT('',(3.05E0,-3.E-1,1.05E1)); -#18434=VERTEX_POINT('',#18432); -#18435=VERTEX_POINT('',#18433); -#18436=CARTESIAN_POINT('',(9.5E-1,-3.E-1,1.05E1)); -#18437=CARTESIAN_POINT('',(1.55E0,-3.E-1,1.05E1)); -#18438=VERTEX_POINT('',#18436); -#18439=VERTEX_POINT('',#18437); -#18440=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,1.05E1)); -#18441=CARTESIAN_POINT('',(5.E-2,-3.E-1,1.05E1)); -#18442=VERTEX_POINT('',#18440); -#18443=VERTEX_POINT('',#18441); -#18444=CARTESIAN_POINT('',(-2.05E0,-3.E-1,1.05E1)); -#18445=CARTESIAN_POINT('',(-1.45E0,-3.E-1,1.05E1)); -#18446=VERTEX_POINT('',#18444); -#18447=VERTEX_POINT('',#18445); -#18448=CARTESIAN_POINT('',(2.45E0,-2.5E-1,9.3E0)); -#18449=CARTESIAN_POINT('',(3.05E0,-2.5E-1,9.3E0)); -#18450=VERTEX_POINT('',#18448); -#18451=VERTEX_POINT('',#18449); -#18452=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,9.3E0)); -#18453=CARTESIAN_POINT('',(1.55E0,-2.5E-1,9.3E0)); -#18454=VERTEX_POINT('',#18452); -#18455=VERTEX_POINT('',#18453); -#18456=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,9.3E0)); -#18457=CARTESIAN_POINT('',(5.E-2,-2.5E-1,9.3E0)); -#18458=VERTEX_POINT('',#18456); -#18459=VERTEX_POINT('',#18457); -#18460=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,9.3E0)); -#18461=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,9.3E0)); -#18462=VERTEX_POINT('',#18460); -#18463=VERTEX_POINT('',#18461); -#18464=CARTESIAN_POINT('',(2.45E0,-3.E-1,9.3E0)); -#18465=CARTESIAN_POINT('',(3.05E0,-3.E-1,9.3E0)); -#18466=VERTEX_POINT('',#18464); -#18467=VERTEX_POINT('',#18465); -#18468=CARTESIAN_POINT('',(9.5E-1,-3.E-1,9.3E0)); -#18469=CARTESIAN_POINT('',(1.55E0,-3.E-1,9.3E0)); -#18470=VERTEX_POINT('',#18468); -#18471=VERTEX_POINT('',#18469); -#18472=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,9.3E0)); -#18473=CARTESIAN_POINT('',(5.E-2,-3.E-1,9.3E0)); -#18474=VERTEX_POINT('',#18472); -#18475=VERTEX_POINT('',#18473); -#18476=CARTESIAN_POINT('',(-2.05E0,-3.E-1,9.3E0)); -#18477=CARTESIAN_POINT('',(-1.45E0,-3.E-1,9.3E0)); -#18478=VERTEX_POINT('',#18476); -#18479=VERTEX_POINT('',#18477); -#18480=CARTESIAN_POINT('',(2.45E0,-2.5E-1,8.1E0)); -#18481=CARTESIAN_POINT('',(3.05E0,-2.5E-1,8.1E0)); -#18482=VERTEX_POINT('',#18480); -#18483=VERTEX_POINT('',#18481); -#18484=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,8.1E0)); -#18485=CARTESIAN_POINT('',(1.55E0,-2.5E-1,8.1E0)); -#18486=VERTEX_POINT('',#18484); -#18487=VERTEX_POINT('',#18485); -#18488=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,8.1E0)); -#18489=CARTESIAN_POINT('',(5.E-2,-2.5E-1,8.1E0)); -#18490=VERTEX_POINT('',#18488); -#18491=VERTEX_POINT('',#18489); -#18492=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,8.1E0)); -#18493=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,8.1E0)); -#18494=VERTEX_POINT('',#18492); -#18495=VERTEX_POINT('',#18493); -#18496=CARTESIAN_POINT('',(2.45E0,-3.E-1,8.1E0)); -#18497=CARTESIAN_POINT('',(3.05E0,-3.E-1,8.1E0)); -#18498=VERTEX_POINT('',#18496); -#18499=VERTEX_POINT('',#18497); -#18500=CARTESIAN_POINT('',(9.5E-1,-3.E-1,8.1E0)); -#18501=CARTESIAN_POINT('',(1.55E0,-3.E-1,8.1E0)); -#18502=VERTEX_POINT('',#18500); -#18503=VERTEX_POINT('',#18501); -#18504=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,8.1E0)); -#18505=CARTESIAN_POINT('',(5.E-2,-3.E-1,8.1E0)); -#18506=VERTEX_POINT('',#18504); -#18507=VERTEX_POINT('',#18505); -#18508=CARTESIAN_POINT('',(-2.05E0,-3.E-1,8.1E0)); -#18509=CARTESIAN_POINT('',(-1.45E0,-3.E-1,8.1E0)); -#18510=VERTEX_POINT('',#18508); -#18511=VERTEX_POINT('',#18509); -#18512=CARTESIAN_POINT('',(2.45E0,-2.5E-1,6.9E0)); -#18513=CARTESIAN_POINT('',(3.05E0,-2.5E-1,6.9E0)); -#18514=VERTEX_POINT('',#18512); -#18515=VERTEX_POINT('',#18513); -#18516=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,6.9E0)); -#18517=CARTESIAN_POINT('',(1.55E0,-2.5E-1,6.9E0)); -#18518=VERTEX_POINT('',#18516); -#18519=VERTEX_POINT('',#18517); -#18520=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,6.9E0)); -#18521=CARTESIAN_POINT('',(5.E-2,-2.5E-1,6.9E0)); -#18522=VERTEX_POINT('',#18520); -#18523=VERTEX_POINT('',#18521); -#18524=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,6.9E0)); -#18525=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,6.9E0)); -#18526=VERTEX_POINT('',#18524); -#18527=VERTEX_POINT('',#18525); -#18528=CARTESIAN_POINT('',(2.45E0,-3.E-1,6.9E0)); -#18529=CARTESIAN_POINT('',(3.05E0,-3.E-1,6.9E0)); -#18530=VERTEX_POINT('',#18528); -#18531=VERTEX_POINT('',#18529); -#18532=CARTESIAN_POINT('',(9.5E-1,-3.E-1,6.9E0)); -#18533=CARTESIAN_POINT('',(1.55E0,-3.E-1,6.9E0)); -#18534=VERTEX_POINT('',#18532); -#18535=VERTEX_POINT('',#18533); -#18536=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,6.9E0)); -#18537=CARTESIAN_POINT('',(5.E-2,-3.E-1,6.9E0)); -#18538=VERTEX_POINT('',#18536); -#18539=VERTEX_POINT('',#18537); -#18540=CARTESIAN_POINT('',(-2.05E0,-3.E-1,6.9E0)); -#18541=CARTESIAN_POINT('',(-1.45E0,-3.E-1,6.9E0)); -#18542=VERTEX_POINT('',#18540); -#18543=VERTEX_POINT('',#18541); -#18544=CARTESIAN_POINT('',(2.45E0,-2.5E-1,5.7E0)); -#18545=CARTESIAN_POINT('',(3.05E0,-2.5E-1,5.7E0)); -#18546=VERTEX_POINT('',#18544); -#18547=VERTEX_POINT('',#18545); -#18548=CARTESIAN_POINT('',(9.5E-1,-2.5E-1,5.7E0)); -#18549=CARTESIAN_POINT('',(1.55E0,-2.5E-1,5.7E0)); -#18550=VERTEX_POINT('',#18548); -#18551=VERTEX_POINT('',#18549); -#18552=CARTESIAN_POINT('',(-5.5E-1,-2.5E-1,5.7E0)); -#18553=CARTESIAN_POINT('',(5.E-2,-2.5E-1,5.7E0)); -#18554=VERTEX_POINT('',#18552); -#18555=VERTEX_POINT('',#18553); -#18556=CARTESIAN_POINT('',(-2.05E0,-2.5E-1,5.7E0)); -#18557=CARTESIAN_POINT('',(-1.45E0,-2.5E-1,5.7E0)); -#18558=VERTEX_POINT('',#18556); -#18559=VERTEX_POINT('',#18557); -#18560=CARTESIAN_POINT('',(2.45E0,-3.E-1,5.7E0)); -#18561=CARTESIAN_POINT('',(3.05E0,-3.E-1,5.7E0)); -#18562=VERTEX_POINT('',#18560); -#18563=VERTEX_POINT('',#18561); -#18564=CARTESIAN_POINT('',(9.5E-1,-3.E-1,5.7E0)); -#18565=CARTESIAN_POINT('',(1.55E0,-3.E-1,5.7E0)); -#18566=VERTEX_POINT('',#18564); -#18567=VERTEX_POINT('',#18565); -#18568=CARTESIAN_POINT('',(-5.5E-1,-3.E-1,5.7E0)); -#18569=CARTESIAN_POINT('',(5.E-2,-3.E-1,5.7E0)); -#18570=VERTEX_POINT('',#18568); -#18571=VERTEX_POINT('',#18569); -#18572=CARTESIAN_POINT('',(-2.05E0,-3.E-1,5.7E0)); -#18573=CARTESIAN_POINT('',(-1.45E0,-3.E-1,5.7E0)); -#18574=VERTEX_POINT('',#18572); -#18575=VERTEX_POINT('',#18573); -#18576=CARTESIAN_POINT('',(4.625E0,-2.5E-1,2.95E0)); -#18577=CARTESIAN_POINT('',(4.625E0,-2.5E-1,4.45E0)); -#18578=VERTEX_POINT('',#18576); -#18579=VERTEX_POINT('',#18577); -#18580=CARTESIAN_POINT('',(3.125E0,-2.5E-1,4.45E0)); -#18581=VERTEX_POINT('',#18580); -#18582=CARTESIAN_POINT('',(3.125E0,-2.5E-1,2.95E0)); -#18583=VERTEX_POINT('',#18582); -#18584=CARTESIAN_POINT('',(2.375E0,-2.5E-1,2.95E0)); -#18585=CARTESIAN_POINT('',(2.375E0,-2.5E-1,4.45E0)); -#18586=VERTEX_POINT('',#18584); -#18587=VERTEX_POINT('',#18585); -#18588=CARTESIAN_POINT('',(8.75E-1,-2.5E-1,4.45E0)); -#18589=VERTEX_POINT('',#18588); -#18590=CARTESIAN_POINT('',(8.75E-1,-2.5E-1,2.95E0)); -#18591=VERTEX_POINT('',#18590); -#18592=CARTESIAN_POINT('',(-3.625E0,-2.5E-1,2.95E0)); -#18593=CARTESIAN_POINT('',(-2.125E0,-2.5E-1,2.95E0)); -#18594=VERTEX_POINT('',#18592); -#18595=VERTEX_POINT('',#18593); -#18596=CARTESIAN_POINT('',(-2.125E0,-2.5E-1,4.45E0)); -#18597=VERTEX_POINT('',#18596); -#18598=CARTESIAN_POINT('',(-3.625E0,-2.5E-1,4.45E0)); -#18599=VERTEX_POINT('',#18598); -#18600=CARTESIAN_POINT('',(-1.375E0,-2.5E-1,2.95E0)); -#18601=CARTESIAN_POINT('',(1.25E-1,-2.5E-1,2.95E0)); -#18602=VERTEX_POINT('',#18600); -#18603=VERTEX_POINT('',#18601); -#18604=CARTESIAN_POINT('',(1.25E-1,-2.5E-1,4.45E0)); -#18605=VERTEX_POINT('',#18604); -#18606=CARTESIAN_POINT('',(-1.375E0,-2.5E-1,4.45E0)); -#18607=VERTEX_POINT('',#18606); -#18608=CARTESIAN_POINT('',(4.625E0,-3.E-1,2.95E0)); -#18609=CARTESIAN_POINT('',(4.625E0,-3.E-1,4.45E0)); -#18610=VERTEX_POINT('',#18608); -#18611=VERTEX_POINT('',#18609); -#18612=CARTESIAN_POINT('',(3.125E0,-3.E-1,4.45E0)); -#18613=VERTEX_POINT('',#18612); -#18614=CARTESIAN_POINT('',(3.125E0,-3.E-1,2.95E0)); -#18615=VERTEX_POINT('',#18614); -#18616=CARTESIAN_POINT('',(2.375E0,-3.E-1,2.95E0)); -#18617=CARTESIAN_POINT('',(2.375E0,-3.E-1,4.45E0)); -#18618=VERTEX_POINT('',#18616); -#18619=VERTEX_POINT('',#18617); -#18620=CARTESIAN_POINT('',(8.75E-1,-3.E-1,4.45E0)); -#18621=VERTEX_POINT('',#18620); -#18622=CARTESIAN_POINT('',(8.75E-1,-3.E-1,2.95E0)); -#18623=VERTEX_POINT('',#18622); -#18624=CARTESIAN_POINT('',(-3.625E0,-3.E-1,2.95E0)); -#18625=CARTESIAN_POINT('',(-2.125E0,-3.E-1,2.95E0)); -#18626=VERTEX_POINT('',#18624); -#18627=VERTEX_POINT('',#18625); -#18628=CARTESIAN_POINT('',(-2.125E0,-3.E-1,4.45E0)); -#18629=VERTEX_POINT('',#18628); -#18630=CARTESIAN_POINT('',(-3.625E0,-3.E-1,4.45E0)); -#18631=VERTEX_POINT('',#18630); -#18632=CARTESIAN_POINT('',(-1.375E0,-3.E-1,2.95E0)); -#18633=CARTESIAN_POINT('',(1.25E-1,-3.E-1,2.95E0)); -#18634=VERTEX_POINT('',#18632); -#18635=VERTEX_POINT('',#18633); -#18636=CARTESIAN_POINT('',(1.25E-1,-3.E-1,4.45E0)); -#18637=VERTEX_POINT('',#18636); -#18638=CARTESIAN_POINT('',(-1.375E0,-3.E-1,4.45E0)); -#18639=VERTEX_POINT('',#18638); -#18640=CARTESIAN_POINT('',(4.E0,1.5E0,1.03375E1)); -#18641=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.03375E1)); -#18642=VERTEX_POINT('',#18640); -#18643=VERTEX_POINT('',#18641); -#18644=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,9.849999982119E0)); -#18645=VERTEX_POINT('',#18644); -#18646=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,9.849999982119E0)); -#18647=VERTEX_POINT('',#18646); -#18648=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.03375E1)); -#18649=VERTEX_POINT('',#18648); -#18650=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.03375E1)); -#18651=VERTEX_POINT('',#18650); -#18652=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.775E0)); -#18653=VERTEX_POINT('',#18652); -#18654=CARTESIAN_POINT('',(3.E0,1.5E0,9.775E0)); -#18655=VERTEX_POINT('',#18654); -#18656=CARTESIAN_POINT('',(3.E0,1.5E0,1.045E1)); -#18657=VERTEX_POINT('',#18656); -#18658=CARTESIAN_POINT('',(4.E0,1.5E0,1.045E1)); -#18659=VERTEX_POINT('',#18658); -#18660=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.893750035763E0)); -#18661=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,9.006250035763E0)); -#18662=VERTEX_POINT('',#18660); -#18663=VERTEX_POINT('',#18661); -#18664=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,9.024999964237E0)); -#18665=VERTEX_POINT('',#18664); -#18666=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.081249964237E0)); -#18667=VERTEX_POINT('',#18666); -#18668=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.15625E0)); -#18669=VERTEX_POINT('',#18668); -#18670=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.325E0)); -#18671=VERTEX_POINT('',#18670); -#18672=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.400000035763E0)); -#18673=VERTEX_POINT('',#18672); -#18674=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,9.456250035763E0)); -#18675=VERTEX_POINT('',#18674); -#18676=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,9.49375E0)); -#18677=VERTEX_POINT('',#18676); -#18678=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,9.512500035763E0)); -#18679=VERTEX_POINT('',#18678); -#18680=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,9.512500035763E0)); -#18681=VERTEX_POINT('',#18680); -#18682=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,9.49375E0)); -#18683=VERTEX_POINT('',#18682); -#18684=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,9.456250035763E0)); -#18685=VERTEX_POINT('',#18684); -#18686=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.400000035763E0)); -#18687=VERTEX_POINT('',#18686); -#18688=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.325E0)); -#18689=VERTEX_POINT('',#18688); -#18690=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.15625E0)); -#18691=VERTEX_POINT('',#18690); -#18692=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.081249964237E0)); -#18693=VERTEX_POINT('',#18692); -#18694=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,9.024999964237E0)); -#18695=VERTEX_POINT('',#18694); -#18696=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,9.006250035763E0)); -#18697=VERTEX_POINT('',#18696); -#18698=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.893750035763E0)); -#18699=VERTEX_POINT('',#18698); -#18700=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.912499964237E0)); -#18701=VERTEX_POINT('',#18700); -#18702=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.9875E0)); -#18703=VERTEX_POINT('',#18702); -#18704=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.062500035763E0)); -#18705=VERTEX_POINT('',#18704); -#18706=CARTESIAN_POINT('',(3.E0,1.5E0,9.15625E0)); -#18707=VERTEX_POINT('',#18706); -#18708=CARTESIAN_POINT('',(3.E0,1.5E0,9.325E0)); -#18709=VERTEX_POINT('',#18708); -#18710=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.418749964237E0)); -#18711=VERTEX_POINT('',#18710); -#18712=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,9.49375E0)); -#18713=VERTEX_POINT('',#18712); -#18714=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,9.568749982119E0)); -#18715=VERTEX_POINT('',#18714); -#18716=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,9.60625E0)); -#18717=VERTEX_POINT('',#18716); -#18718=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,9.624999982119E0)); -#18719=VERTEX_POINT('',#18718); -#18720=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,9.624999982119E0)); -#18721=VERTEX_POINT('',#18720); -#18722=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,9.60625E0)); -#18723=VERTEX_POINT('',#18722); -#18724=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,9.568749982119E0)); -#18725=VERTEX_POINT('',#18724); -#18726=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,9.49375E0)); -#18727=VERTEX_POINT('',#18726); -#18728=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.418749964237E0)); -#18729=VERTEX_POINT('',#18728); -#18730=CARTESIAN_POINT('',(4.E0,1.5E0,9.325E0)); -#18731=VERTEX_POINT('',#18730); -#18732=CARTESIAN_POINT('',(4.E0,1.5E0,9.15625E0)); -#18733=VERTEX_POINT('',#18732); -#18734=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.062500035763E0)); -#18735=VERTEX_POINT('',#18734); -#18736=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.9875E0)); -#18737=VERTEX_POINT('',#18736); -#18738=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.912499964237E0)); -#18739=VERTEX_POINT('',#18738); -#18740=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.012500071526E0)); -#18741=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.125000071526E0)); -#18742=VERTEX_POINT('',#18740); -#18743=VERTEX_POINT('',#18741); -#18744=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,8.14375E0)); -#18745=VERTEX_POINT('',#18744); -#18746=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.2E0)); -#18747=VERTEX_POINT('',#18746); -#18748=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,8.274999928474E0)); -#18749=VERTEX_POINT('',#18748); -#18750=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,8.443749928474E0)); -#18751=VERTEX_POINT('',#18750); -#18752=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.518750071526E0)); -#18753=VERTEX_POINT('',#18752); -#18754=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,8.575000071526E0)); -#18755=VERTEX_POINT('',#18754); -#18756=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,8.612499928474E0)); -#18757=VERTEX_POINT('',#18756); -#18758=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,8.631250071526E0)); -#18759=VERTEX_POINT('',#18758); -#18760=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,8.631250071526E0)); -#18761=VERTEX_POINT('',#18760); -#18762=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.612499928474E0)); -#18763=VERTEX_POINT('',#18762); -#18764=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,8.575000071526E0)); -#18765=VERTEX_POINT('',#18764); -#18766=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.518750071526E0)); -#18767=VERTEX_POINT('',#18766); -#18768=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,8.443749928474E0)); -#18769=VERTEX_POINT('',#18768); -#18770=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,8.274999928474E0)); -#18771=VERTEX_POINT('',#18770); -#18772=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.2E0)); -#18773=VERTEX_POINT('',#18772); -#18774=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,8.14375E0)); -#18775=VERTEX_POINT('',#18774); -#18776=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.125000071526E0)); -#18777=VERTEX_POINT('',#18776); -#18778=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,8.012500071526E0)); -#18779=VERTEX_POINT('',#18778); -#18780=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.03125E0)); -#18781=VERTEX_POINT('',#18780); -#18782=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.106249928474E0)); -#18783=VERTEX_POINT('',#18782); -#18784=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,8.181250071526E0)); -#18785=VERTEX_POINT('',#18784); -#18786=CARTESIAN_POINT('',(3.E0,1.5E0,8.274999928474E0)); -#18787=VERTEX_POINT('',#18786); -#18788=CARTESIAN_POINT('',(3.E0,1.5E0,8.443749928474E0)); -#18789=VERTEX_POINT('',#18788); -#18790=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,8.5375E0)); -#18791=VERTEX_POINT('',#18790); -#18792=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,8.612499928474E0)); -#18793=VERTEX_POINT('',#18792); -#18794=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,8.687499964237E0)); -#18795=VERTEX_POINT('',#18794); -#18796=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,8.725000035763E0)); -#18797=VERTEX_POINT('',#18796); -#18798=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,8.743749964237E0)); -#18799=VERTEX_POINT('',#18798); -#18800=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,8.743749964237E0)); -#18801=VERTEX_POINT('',#18800); -#18802=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,8.725000035763E0)); -#18803=VERTEX_POINT('',#18802); -#18804=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.687499964237E0)); -#18805=VERTEX_POINT('',#18804); -#18806=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.612499928474E0)); -#18807=VERTEX_POINT('',#18806); -#18808=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,8.5375E0)); -#18809=VERTEX_POINT('',#18808); -#18810=CARTESIAN_POINT('',(4.E0,1.5E0,8.443749928474E0)); -#18811=VERTEX_POINT('',#18810); -#18812=CARTESIAN_POINT('',(4.E0,1.5E0,8.274999928474E0)); -#18813=VERTEX_POINT('',#18812); -#18814=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,8.181250071526E0)); -#18815=VERTEX_POINT('',#18814); -#18816=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,8.106249928474E0)); -#18817=VERTEX_POINT('',#18816); -#18818=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,8.03125E0)); -#18819=VERTEX_POINT('',#18818); -#18820=CARTESIAN_POINT('',(4.E0,1.5E0,7.75E0)); -#18821=CARTESIAN_POINT('',(3.E0,1.5E0,7.75E0)); -#18822=VERTEX_POINT('',#18820); -#18823=VERTEX_POINT('',#18821); -#18824=CARTESIAN_POINT('',(3.E0,1.5E0,7.8625E0)); -#18825=VERTEX_POINT('',#18824); -#18826=CARTESIAN_POINT('',(4.E0,1.5E0,7.8625E0)); -#18827=VERTEX_POINT('',#18826); -#18828=CARTESIAN_POINT('',(3.E0,1.5E0,7.149999928474E0)); -#18829=CARTESIAN_POINT('',(3.E0,1.5E0,7.599999928474E0)); -#18830=VERTEX_POINT('',#18828); -#18831=VERTEX_POINT('',#18829); -#18832=CARTESIAN_POINT('',(4.E0,1.5E0,7.599999928474E0)); -#18833=VERTEX_POINT('',#18832); -#18834=CARTESIAN_POINT('',(4.E0,1.5E0,7.149999928474E0)); -#18835=VERTEX_POINT('',#18834); -#18836=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,7.056250071526E0)); -#18837=VERTEX_POINT('',#18836); -#18838=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,6.981249928474E0)); -#18839=VERTEX_POINT('',#18838); -#18840=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,6.90625E0)); -#18841=VERTEX_POINT('',#18840); -#18842=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,6.868749928474E0)); -#18843=VERTEX_POINT('',#18842); -#18844=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,6.85E0)); -#18845=VERTEX_POINT('',#18844); -#18846=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,6.85E0)); -#18847=VERTEX_POINT('',#18846); -#18848=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,6.868749928474E0)); -#18849=VERTEX_POINT('',#18848); -#18850=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,6.90625E0)); -#18851=VERTEX_POINT('',#18850); -#18852=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,6.981249928474E0)); -#18853=VERTEX_POINT('',#18852); -#18854=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,7.056250071526E0)); -#18855=VERTEX_POINT('',#18854); -#18856=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,7.487499928474E0)); -#18857=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,7.149999928474E0)); -#18858=VERTEX_POINT('',#18856); -#18859=VERTEX_POINT('',#18857); -#18860=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,7.075E0)); -#18861=VERTEX_POINT('',#18860); -#18862=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,7.01875E0)); -#18863=VERTEX_POINT('',#18862); -#18864=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,6.981249928474E0)); -#18865=VERTEX_POINT('',#18864); -#18866=CARTESIAN_POINT('',(3.340425550938E0,1.5E0,6.9625E0)); -#18867=VERTEX_POINT('',#18866); -#18868=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,6.9625E0)); -#18869=VERTEX_POINT('',#18868); -#18870=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,6.981249928474E0)); -#18871=VERTEX_POINT('',#18870); -#18872=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,7.01875E0)); -#18873=VERTEX_POINT('',#18872); -#18874=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,7.075E0)); -#18875=VERTEX_POINT('',#18874); -#18876=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,7.149999928474E0)); -#18877=VERTEX_POINT('',#18876); -#18878=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,7.487499928474E0)); -#18879=VERTEX_POINT('',#18878); -#18880=CARTESIAN_POINT('',(4.E0,1.5E0,6.606249856949E0)); -#18881=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,6.606249856949E0)); -#18882=VERTEX_POINT('',#18880); -#18883=VERTEX_POINT('',#18881); -#18884=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,6.700000143051E0)); -#18885=VERTEX_POINT('',#18884); -#18886=CARTESIAN_POINT('',(4.E0,1.5E0,6.700000143051E0)); -#18887=VERTEX_POINT('',#18886); -#18888=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.606249856949E0)); -#18889=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,6.606249856949E0)); -#18890=VERTEX_POINT('',#18888); -#18891=VERTEX_POINT('',#18889); -#18892=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,6.700000143051E0)); -#18893=VERTEX_POINT('',#18892); -#18894=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.700000143051E0)); -#18895=VERTEX_POINT('',#18894); -#18896=CARTESIAN_POINT('',(4.E0,1.5E0,5.818749856949E0)); -#18897=CARTESIAN_POINT('',(4.E0,1.5E0,5.706249856949E0)); -#18898=VERTEX_POINT('',#18896); -#18899=VERTEX_POINT('',#18897); -#18900=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.025000143051E0)); -#18901=VERTEX_POINT('',#18900); -#18902=CARTESIAN_POINT('',(3.E0,1.5E0,5.706249856949E0)); -#18903=VERTEX_POINT('',#18902); -#18904=CARTESIAN_POINT('',(3.E0,1.5E0,5.818749856949E0)); -#18905=VERTEX_POINT('',#18904); -#18906=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,6.081250143051E0)); -#18907=VERTEX_POINT('',#18906); -#18908=CARTESIAN_POINT('',(3.E0,1.5E0,6.34375E0)); -#18909=VERTEX_POINT('',#18908); -#18910=CARTESIAN_POINT('',(3.E0,1.5E0,6.45625E0)); -#18911=VERTEX_POINT('',#18910); -#18912=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.137500143051E0)); -#18913=VERTEX_POINT('',#18912); -#18914=CARTESIAN_POINT('',(4.E0,1.5E0,6.45625E0)); -#18915=VERTEX_POINT('',#18914); -#18916=CARTESIAN_POINT('',(4.E0,1.5E0,6.34375E0)); -#18917=VERTEX_POINT('',#18916); -#18918=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,6.081250143051E0)); -#18919=VERTEX_POINT('',#18918); -#18920=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,5.406250143051E0)); -#18921=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,5.44375E0)); -#18922=VERTEX_POINT('',#18920); -#18923=VERTEX_POINT('',#18921); -#18924=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,5.518750143051E0)); -#18925=VERTEX_POINT('',#18924); -#18926=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.55625E0)); -#18927=VERTEX_POINT('',#18926); -#18928=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,5.55625E0)); -#18929=VERTEX_POINT('',#18928); -#18930=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,5.518750143051E0)); -#18931=VERTEX_POINT('',#18930); -#18932=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,5.462500143051E0)); -#18933=VERTEX_POINT('',#18932); -#18934=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,5.368749856949E0)); -#18935=VERTEX_POINT('',#18934); -#18936=CARTESIAN_POINT('',(4.E0,1.5E0,5.275E0)); -#18937=VERTEX_POINT('',#18936); -#18938=CARTESIAN_POINT('',(4.E0,1.5E0,5.1625E0)); -#18939=VERTEX_POINT('',#18938); -#18940=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,5.068750143051E0)); -#18941=VERTEX_POINT('',#18940); -#18942=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,4.974999856949E0)); -#18943=VERTEX_POINT('',#18942); -#18944=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,4.918749856949E0)); -#18945=VERTEX_POINT('',#18944); -#18946=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,4.88125E0)); -#18947=VERTEX_POINT('',#18946); -#18948=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.88125E0)); -#18949=VERTEX_POINT('',#18948); -#18950=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,4.918749856949E0)); -#18951=VERTEX_POINT('',#18950); -#18952=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,4.99375E0)); -#18953=VERTEX_POINT('',#18952); -#18954=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,5.031249856949E0)); -#18955=VERTEX_POINT('',#18954); -#18956=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,4.99375E0)); -#18957=VERTEX_POINT('',#18956); -#18958=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,4.9375E0)); -#18959=VERTEX_POINT('',#18958); -#18960=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,4.900000143051E0)); -#18961=VERTEX_POINT('',#18960); -#18962=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,4.900000143051E0)); -#18963=VERTEX_POINT('',#18962); -#18964=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,4.9375E0)); -#18965=VERTEX_POINT('',#18964); -#18966=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,4.99375E0)); -#18967=VERTEX_POINT('',#18966); -#18968=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,5.087499856949E0)); -#18969=VERTEX_POINT('',#18968); -#18970=CARTESIAN_POINT('',(3.E0,1.5E0,5.181250143051E0)); -#18971=VERTEX_POINT('',#18970); -#18972=CARTESIAN_POINT('',(3.E0,1.5E0,5.256249856949E0)); -#18973=VERTEX_POINT('',#18972); -#18974=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,5.350000143051E0)); -#18975=VERTEX_POINT('',#18974); -#18976=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,5.44375E0)); -#18977=VERTEX_POINT('',#18976); -#18978=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,5.5E0)); -#18979=VERTEX_POINT('',#18978); -#18980=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,5.537499856949E0)); -#18981=VERTEX_POINT('',#18980); -#18982=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,5.537499856949E0)); -#18983=VERTEX_POINT('',#18982); -#18984=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,5.5E0)); -#18985=VERTEX_POINT('',#18984); -#18986=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,5.44375E0)); -#18987=VERTEX_POINT('',#18986); -#18988=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.256249856949E0)); -#18989=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,5.33125E0)); -#18990=VERTEX_POINT('',#18988); -#18991=VERTEX_POINT('',#18989); -#18992=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,5.406250143051E0)); -#18993=VERTEX_POINT('',#18992); -#18994=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,5.462500143051E0)); -#18995=VERTEX_POINT('',#18994); -#18996=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.462500143051E0)); -#18997=VERTEX_POINT('',#18996); -#18998=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,5.406250143051E0)); -#18999=VERTEX_POINT('',#18998); -#19000=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,5.33125E0)); -#19001=VERTEX_POINT('',#19000); -#19002=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.256249856949E0)); -#19003=VERTEX_POINT('',#19002); -#19004=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.181250143051E0)); -#19005=VERTEX_POINT('',#19004); -#19006=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,5.10625E0)); -#19007=VERTEX_POINT('',#19006); -#19008=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,5.031249856949E0)); -#19009=VERTEX_POINT('',#19008); -#19010=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.974999856949E0)); -#19011=VERTEX_POINT('',#19010); -#19012=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,4.974999856949E0)); -#19013=VERTEX_POINT('',#19012); -#19014=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,5.031249856949E0)); -#19015=VERTEX_POINT('',#19014); -#19016=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,5.10625E0)); -#19017=VERTEX_POINT('',#19016); -#19018=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.181250143051E0)); -#19019=VERTEX_POINT('',#19018); -#19020=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,5.181250143051E0)); -#19021=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,5.10625E0)); -#19022=VERTEX_POINT('',#19020); -#19023=VERTEX_POINT('',#19021); -#19024=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,5.031249856949E0)); -#19025=VERTEX_POINT('',#19024); -#19026=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,4.99375E0)); -#19027=VERTEX_POINT('',#19026); -#19028=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,4.99375E0)); -#19029=VERTEX_POINT('',#19028); -#19030=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.031249856949E0)); -#19031=VERTEX_POINT('',#19030); -#19032=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.10625E0)); -#19033=VERTEX_POINT('',#19032); -#19034=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,5.181250143051E0)); -#19035=VERTEX_POINT('',#19034); -#19036=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,5.256249856949E0)); -#19037=VERTEX_POINT('',#19036); -#19038=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.33125E0)); -#19039=VERTEX_POINT('',#19038); -#19040=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.406250143051E0)); -#19041=VERTEX_POINT('',#19040); -#19042=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,5.44375E0)); -#19043=VERTEX_POINT('',#19042); -#19044=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,5.44375E0)); -#19045=VERTEX_POINT('',#19044); -#19046=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,5.406250143051E0)); -#19047=VERTEX_POINT('',#19046); -#19048=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,5.33125E0)); -#19049=VERTEX_POINT('',#19048); -#19050=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,5.256249856949E0)); -#19051=VERTEX_POINT('',#19050); -#19052=CARTESIAN_POINT('',(4.E0,1.5E0,4.43125E0)); -#19053=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,4.281250143051E0)); -#19054=VERTEX_POINT('',#19052); -#19055=VERTEX_POINT('',#19053); -#19056=CARTESIAN_POINT('',(4.E0,1.5E0,4.131249856949E0)); -#19057=VERTEX_POINT('',#19056); -#19058=CARTESIAN_POINT('',(4.E0,1.5E0,3.98125E0)); -#19059=VERTEX_POINT('',#19058); -#19060=CARTESIAN_POINT('',(3.E0,1.5E0,3.831250143051E0)); -#19061=VERTEX_POINT('',#19060); -#19062=CARTESIAN_POINT('',(3.E0,1.5E0,3.943750143051E0)); -#19063=VERTEX_POINT('',#19062); -#19064=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.056250143051E0)); -#19065=VERTEX_POINT('',#19064); -#19066=CARTESIAN_POINT('',(3.E0,1.5E0,4.20625E0)); -#19067=VERTEX_POINT('',#19066); -#19068=CARTESIAN_POINT('',(3.E0,1.5E0,4.356249856949E0)); -#19069=VERTEX_POINT('',#19068); -#19070=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.506250143051E0)); -#19071=VERTEX_POINT('',#19070); -#19072=CARTESIAN_POINT('',(3.E0,1.5E0,4.618750143051E0)); -#19073=VERTEX_POINT('',#19072); -#19074=CARTESIAN_POINT('',(3.E0,1.5E0,4.731250143051E0)); -#19075=VERTEX_POINT('',#19074); -#19076=CARTESIAN_POINT('',(4.E0,1.5E0,4.581249856949E0)); -#19077=VERTEX_POINT('',#19076); -#19078=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,3.099999713898E0)); -#19079=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,3.062500286102E0)); -#19080=VERTEX_POINT('',#19078); -#19081=VERTEX_POINT('',#19079); -#19082=CARTESIAN_POINT('',(3.382978737354E0,1.5E0,3.006250286102E0)); -#19083=VERTEX_POINT('',#19082); -#19084=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,2.987499713898E0)); -#19085=VERTEX_POINT('',#19084); -#19086=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,2.987499713898E0)); -#19087=VERTEX_POINT('',#19086); -#19088=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,3.006250286102E0)); -#19089=VERTEX_POINT('',#19088); -#19090=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,3.062500286102E0)); -#19091=VERTEX_POINT('',#19090); -#19092=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,3.1375E0)); -#19093=VERTEX_POINT('',#19092); -#19094=CARTESIAN_POINT('',(3.E0,1.5E0,3.231250286102E0)); -#19095=VERTEX_POINT('',#19094); -#19096=CARTESIAN_POINT('',(3.E0,1.5E0,3.681249856949E0)); -#19097=VERTEX_POINT('',#19096); -#19098=CARTESIAN_POINT('',(4.E0,1.5E0,3.681249856949E0)); -#19099=VERTEX_POINT('',#19098); -#19100=CARTESIAN_POINT('',(4.E0,1.5E0,3.231250286102E0)); -#19101=VERTEX_POINT('',#19100); -#19102=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,3.1375E0)); -#19103=VERTEX_POINT('',#19102); -#19104=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,3.062500286102E0)); -#19105=VERTEX_POINT('',#19104); -#19106=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,3.006250286102E0)); -#19107=VERTEX_POINT('',#19106); -#19108=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,2.987499713898E0)); -#19109=VERTEX_POINT('',#19108); -#19110=CARTESIAN_POINT('',(3.659574478865E0,1.5E0,2.987499713898E0)); -#19111=VERTEX_POINT('',#19110); -#19112=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,3.006250286102E0)); -#19113=VERTEX_POINT('',#19112); -#19114=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,3.062500286102E0)); -#19115=VERTEX_POINT('',#19114); -#19116=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,3.568749856949E0)); -#19117=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,3.212499713898E0)); -#19118=VERTEX_POINT('',#19116); -#19119=VERTEX_POINT('',#19117); -#19120=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,3.156249713898E0)); -#19121=VERTEX_POINT('',#19120); -#19122=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,3.118750286102E0)); -#19123=VERTEX_POINT('',#19122); -#19124=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,3.099999713898E0)); -#19125=VERTEX_POINT('',#19124); -#19126=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,3.099999713898E0)); -#19127=VERTEX_POINT('',#19126); -#19128=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,3.118750286102E0)); -#19129=VERTEX_POINT('',#19128); -#19130=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,3.156249713898E0)); -#19131=VERTEX_POINT('',#19130); -#19132=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,3.212499713898E0)); -#19133=VERTEX_POINT('',#19132); -#19134=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,3.568749856949E0)); -#19135=VERTEX_POINT('',#19134); -#19136=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,3.099999713898E0)); -#19137=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,3.099999713898E0)); -#19138=VERTEX_POINT('',#19136); -#19139=VERTEX_POINT('',#19137); -#19140=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,3.118750286102E0)); -#19141=VERTEX_POINT('',#19140); -#19142=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,3.156249713898E0)); -#19143=VERTEX_POINT('',#19142); -#19144=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,3.212499713898E0)); -#19145=VERTEX_POINT('',#19144); -#19146=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,3.568749856949E0)); -#19147=VERTEX_POINT('',#19146); -#19148=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,3.568749856949E0)); -#19149=VERTEX_POINT('',#19148); -#19150=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,3.212499713898E0)); -#19151=VERTEX_POINT('',#19150); -#19152=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,3.156249713898E0)); -#19153=VERTEX_POINT('',#19152); -#19154=CARTESIAN_POINT('',(3.617021262646E0,1.5E0,3.118750286102E0)); -#19155=VERTEX_POINT('',#19154); -#19156=CARTESIAN_POINT('',(3.E0,1.5E0,2.125E0)); -#19157=CARTESIAN_POINT('',(3.E0,1.5E0,2.837500286102E0)); -#19158=VERTEX_POINT('',#19156); -#19159=VERTEX_POINT('',#19157); -#19160=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.837500286102E0)); -#19161=VERTEX_POINT('',#19160); -#19162=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.537499713898E0)); -#19163=VERTEX_POINT('',#19162); -#19164=CARTESIAN_POINT('',(4.E0,1.5E0,2.537499713898E0)); -#19165=VERTEX_POINT('',#19164); -#19166=CARTESIAN_POINT('',(4.E0,1.5E0,2.424999713898E0)); -#19167=VERTEX_POINT('',#19166); -#19168=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.424999713898E0)); -#19169=VERTEX_POINT('',#19168); -#19170=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.125E0)); -#19171=VERTEX_POINT('',#19170); -#19172=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,1.825000286102E0)); -#19173=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,1.862499713898E0)); -#19174=VERTEX_POINT('',#19172); -#19175=VERTEX_POINT('',#19173); -#19176=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,1.937500286102E0)); -#19177=VERTEX_POINT('',#19176); -#19178=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.974999713898E0)); -#19179=VERTEX_POINT('',#19178); -#19180=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.974999713898E0)); -#19181=VERTEX_POINT('',#19180); -#19182=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.937500286102E0)); -#19183=VERTEX_POINT('',#19182); -#19184=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,1.881250286102E0)); -#19185=VERTEX_POINT('',#19184); -#19186=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,1.7875E0)); -#19187=VERTEX_POINT('',#19186); -#19188=CARTESIAN_POINT('',(4.E0,1.5E0,1.693749713898E0)); -#19189=VERTEX_POINT('',#19188); -#19190=CARTESIAN_POINT('',(4.E0,1.5E0,1.581249713898E0)); -#19191=VERTEX_POINT('',#19190); -#19192=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,1.487500286102E0)); -#19193=VERTEX_POINT('',#19192); -#19194=CARTESIAN_POINT('',(3.914893619716E0,1.5E0,1.39375E0)); -#19195=VERTEX_POINT('',#19194); -#19196=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.3375E0)); -#19197=VERTEX_POINT('',#19196); -#19198=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.299999713898E0)); -#19199=VERTEX_POINT('',#19198); -#19200=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.299999713898E0)); -#19201=VERTEX_POINT('',#19200); -#19202=CARTESIAN_POINT('',(3.574468076229E0,1.5E0,1.3375E0)); -#19203=VERTEX_POINT('',#19202); -#19204=CARTESIAN_POINT('',(3.510638296604E0,1.5E0,1.412499713898E0)); -#19205=VERTEX_POINT('',#19204); -#19206=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,1.45E0)); -#19207=VERTEX_POINT('',#19206); -#19208=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,1.412499713898E0)); -#19209=VERTEX_POINT('',#19208); -#19210=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.356249713898E0)); -#19211=VERTEX_POINT('',#19210); -#19212=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,1.318750286102E0)); -#19213=VERTEX_POINT('',#19212); -#19214=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.318750286102E0)); -#19215=VERTEX_POINT('',#19214); -#19216=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.356249713898E0)); -#19217=VERTEX_POINT('',#19216); -#19218=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,1.412499713898E0)); -#19219=VERTEX_POINT('',#19218); -#19220=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.50625E0)); -#19221=VERTEX_POINT('',#19220); -#19222=CARTESIAN_POINT('',(3.E0,1.5E0,1.600000286102E0)); -#19223=VERTEX_POINT('',#19222); -#19224=CARTESIAN_POINT('',(3.E0,1.5E0,1.675E0)); -#19225=VERTEX_POINT('',#19224); -#19226=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.768750286102E0)); -#19227=VERTEX_POINT('',#19226); -#19228=CARTESIAN_POINT('',(3.085106372833E0,1.5E0,1.862499713898E0)); -#19229=VERTEX_POINT('',#19228); -#19230=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.918749713898E0)); -#19231=VERTEX_POINT('',#19230); -#19232=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.95625E0)); -#19233=VERTEX_POINT('',#19232); -#19234=CARTESIAN_POINT('',(3.319148957729E0,1.5E0,1.95625E0)); -#19235=VERTEX_POINT('',#19234); -#19236=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,1.918749713898E0)); -#19237=VERTEX_POINT('',#19236); -#19238=CARTESIAN_POINT('',(3.468085110188E0,1.5E0,1.862499713898E0)); -#19239=VERTEX_POINT('',#19238); -#19240=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.675E0)); -#19241=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,1.749999713898E0)); -#19242=VERTEX_POINT('',#19240); -#19243=VERTEX_POINT('',#19241); -#19244=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.825000286102E0)); -#19245=VERTEX_POINT('',#19244); -#19246=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.881250286102E0)); -#19247=VERTEX_POINT('',#19246); -#19248=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.881250286102E0)); -#19249=VERTEX_POINT('',#19248); -#19250=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,1.825000286102E0)); -#19251=VERTEX_POINT('',#19250); -#19252=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,1.749999713898E0)); -#19253=VERTEX_POINT('',#19252); -#19254=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.675E0)); -#19255=VERTEX_POINT('',#19254); -#19256=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,1.600000286102E0)); -#19257=VERTEX_POINT('',#19256); -#19258=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,1.524999713898E0)); -#19259=VERTEX_POINT('',#19258); -#19260=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,1.45E0)); -#19261=VERTEX_POINT('',#19260); -#19262=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,1.39375E0)); -#19263=VERTEX_POINT('',#19262); -#19264=CARTESIAN_POINT('',(3.744680851698E0,1.5E0,1.39375E0)); -#19265=VERTEX_POINT('',#19264); -#19266=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.45E0)); -#19267=VERTEX_POINT('',#19266); -#19268=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,1.524999713898E0)); -#19269=VERTEX_POINT('',#19268); -#19270=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.600000286102E0)); -#19271=VERTEX_POINT('',#19270); -#19272=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,1.600000286102E0)); -#19273=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.524999713898E0)); -#19274=VERTEX_POINT('',#19272); -#19275=VERTEX_POINT('',#19273); -#19276=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,1.45E0)); -#19277=VERTEX_POINT('',#19276); -#19278=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.412499713898E0)); -#19279=VERTEX_POINT('',#19278); -#19280=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,1.412499713898E0)); -#19281=VERTEX_POINT('',#19280); -#19282=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,1.45E0)); -#19283=VERTEX_POINT('',#19282); -#19284=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,1.524999713898E0)); -#19285=VERTEX_POINT('',#19284); -#19286=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,1.600000286102E0)); -#19287=VERTEX_POINT('',#19286); -#19288=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,1.675E0)); -#19289=VERTEX_POINT('',#19288); -#19290=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,1.749999713898E0)); -#19291=VERTEX_POINT('',#19290); -#19292=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,1.825000286102E0)); -#19293=VERTEX_POINT('',#19292); -#19294=CARTESIAN_POINT('',(3.297872364521E0,1.5E0,1.862499713898E0)); -#19295=VERTEX_POINT('',#19294); -#19296=CARTESIAN_POINT('',(3.255319178104E0,1.5E0,1.862499713898E0)); -#19297=VERTEX_POINT('',#19296); -#19298=CARTESIAN_POINT('',(3.191489338875E0,1.5E0,1.825000286102E0)); -#19299=VERTEX_POINT('',#19298); -#19300=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.749999713898E0)); -#19301=VERTEX_POINT('',#19300); -#19302=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,1.675E0)); -#19303=VERTEX_POINT('',#19302); -#19304=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,5.312502861023E-1)); -#19305=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,4.9375E-1)); -#19306=VERTEX_POINT('',#19304); -#19307=VERTEX_POINT('',#19305); -#19308=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,4.750002861023E-1)); -#19309=VERTEX_POINT('',#19308); -#19310=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,4.750002861023E-1)); -#19311=VERTEX_POINT('',#19310); -#19312=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,4.9375E-1)); -#19313=VERTEX_POINT('',#19312); -#19314=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,5.312502861023E-1)); -#19315=VERTEX_POINT('',#19314); -#19316=CARTESIAN_POINT('',(3.489361703396E0,1.5E0,6.249997138977E-1)); -#19317=VERTEX_POINT('',#19316); -#19318=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,5.5E-1)); -#19319=VERTEX_POINT('',#19318); -#19320=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,5.124997138977E-1)); -#19321=VERTEX_POINT('',#19320); -#19322=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,4.9375E-1)); -#19323=VERTEX_POINT('',#19322); -#19324=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,4.9375E-1)); -#19325=VERTEX_POINT('',#19324); -#19326=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,5.124997138977E-1)); -#19327=VERTEX_POINT('',#19326); -#19328=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,5.875002861023E-1)); -#19329=VERTEX_POINT('',#19328); -#19330=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,6.625E-1)); -#19331=VERTEX_POINT('',#19330); -#19332=CARTESIAN_POINT('',(3.E0,1.5E0,7.937497138977E-1)); -#19333=VERTEX_POINT('',#19332); -#19334=CARTESIAN_POINT('',(3.E0,1.5E0,8.3125E-1)); -#19335=VERTEX_POINT('',#19334); -#19336=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,9.624997138977E-1)); -#19337=VERTEX_POINT('',#19336); -#19338=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,1.037500286102E0)); -#19339=VERTEX_POINT('',#19338); -#19340=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,1.1125E0)); -#19341=VERTEX_POINT('',#19340); -#19342=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,1.131249713898E0)); -#19343=VERTEX_POINT('',#19342); -#19344=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,1.037500286102E0)); -#19345=VERTEX_POINT('',#19344); -#19346=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,1.E0)); -#19347=VERTEX_POINT('',#19346); -#19348=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,9.4375E-1)); -#19349=VERTEX_POINT('',#19348); -#19350=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,8.499997138977E-1)); -#19351=VERTEX_POINT('',#19350); -#19352=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,7.75E-1)); -#19353=VERTEX_POINT('',#19352); -#19354=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,6.812497138977E-1)); -#19355=VERTEX_POINT('',#19354); -#19356=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,6.249997138977E-1)); -#19357=VERTEX_POINT('',#19356); -#19358=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,5.875002861023E-1)); -#19359=VERTEX_POINT('',#19358); -#19360=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,5.875002861023E-1)); -#19361=VERTEX_POINT('',#19360); -#19362=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,6.249997138977E-1)); -#19363=VERTEX_POINT('',#19362); -#19364=CARTESIAN_POINT('',(3.404255330563E0,1.5E0,6.625E-1)); -#19365=VERTEX_POINT('',#19364); -#19366=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,7.75E-1)); -#19367=VERTEX_POINT('',#19366); -#19368=CARTESIAN_POINT('',(3.446808516979E0,1.5E0,8.499997138977E-1)); -#19369=VERTEX_POINT('',#19368); -#19370=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,8.499997138977E-1)); -#19371=VERTEX_POINT('',#19370); -#19372=CARTESIAN_POINT('',(3.531914889812E0,1.5E0,7.75E-1)); -#19373=VERTEX_POINT('',#19372); -#19374=CARTESIAN_POINT('',(3.553191483021E0,1.5E0,6.625E-1)); -#19375=VERTEX_POINT('',#19374); -#19376=CARTESIAN_POINT('',(3.595744669437E0,1.5E0,6.0625E-1)); -#19377=VERTEX_POINT('',#19376); -#19378=CARTESIAN_POINT('',(3.680851072073E0,1.5E0,5.687497138977E-1)); -#19379=VERTEX_POINT('',#19378); -#19380=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,5.687497138977E-1)); -#19381=VERTEX_POINT('',#19380); -#19382=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,5.875002861023E-1)); -#19383=VERTEX_POINT('',#19382); -#19384=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,6.249997138977E-1)); -#19385=VERTEX_POINT('',#19384); -#19386=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,6.625E-1)); -#19387=VERTEX_POINT('',#19386); -#19388=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,7.562502861023E-1)); -#19389=VERTEX_POINT('',#19388); -#19390=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,8.687502861023E-1)); -#19391=VERTEX_POINT('',#19390); -#19392=CARTESIAN_POINT('',(3.872340425849E0,1.5E0,9.624997138977E-1)); -#19393=VERTEX_POINT('',#19392); -#19394=CARTESIAN_POINT('',(3.851063832641E0,1.5E0,1.E0)); -#19395=VERTEX_POINT('',#19394); -#19396=CARTESIAN_POINT('',(3.808510631323E0,1.5E0,1.037500286102E0)); -#19397=VERTEX_POINT('',#19396); -#19398=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,1.05625E0)); -#19399=VERTEX_POINT('',#19398); -#19400=CARTESIAN_POINT('',(3.765957444906E0,1.5E0,1.150000286102E0)); -#19401=VERTEX_POINT('',#19400); -#19402=CARTESIAN_POINT('',(3.829787239432E0,1.5E0,1.131249713898E0)); -#19403=VERTEX_POINT('',#19402); -#19404=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.093750286102E0)); -#19405=VERTEX_POINT('',#19404); -#19406=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,1.037500286102E0)); -#19407=VERTEX_POINT('',#19406); -#19408=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,9.624997138977E-1)); -#19409=VERTEX_POINT('',#19408); -#19410=CARTESIAN_POINT('',(4.E0,1.5E0,8.875E-1)); -#19411=VERTEX_POINT('',#19410); -#19412=CARTESIAN_POINT('',(4.E0,1.5E0,7.374997138977E-1)); -#19413=VERTEX_POINT('',#19412); -#19414=CARTESIAN_POINT('',(3.978723404929E0,1.5E0,6.625E-1)); -#19415=VERTEX_POINT('',#19414); -#19416=CARTESIAN_POINT('',(3.936170212924E0,1.5E0,5.875002861023E-1)); -#19417=VERTEX_POINT('',#19416); -#19418=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,3.25E-1)); -#19419=CARTESIAN_POINT('',(4.E0,1.5E0,3.25E-1)); -#19420=VERTEX_POINT('',#19418); -#19421=VERTEX_POINT('',#19419); -#19422=CARTESIAN_POINT('',(4.E0,1.5E0,-3.5E-1)); -#19423=VERTEX_POINT('',#19422); -#19424=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,-3.5E-1)); -#19425=VERTEX_POINT('',#19424); -#19426=CARTESIAN_POINT('',(3.893617019057E0,1.5E0,1.749997138977E-1)); -#19427=VERTEX_POINT('',#19426); -#19428=CARTESIAN_POINT('',(3.425531923771E0,1.5E0,-2.9375E-1)); -#19429=VERTEX_POINT('',#19428); -#19430=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,-3.312502861023E-1)); -#19431=VERTEX_POINT('',#19430); -#19432=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,-3.5E-1)); -#19433=VERTEX_POINT('',#19432); -#19434=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,-3.5E-1)); -#19435=VERTEX_POINT('',#19434); -#19436=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,-3.312502861023E-1)); -#19437=VERTEX_POINT('',#19436); -#19438=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,-2.562497138977E-1)); -#19439=VERTEX_POINT('',#19438); -#19440=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,-1.8125E-1)); -#19441=VERTEX_POINT('',#19440); -#19442=CARTESIAN_POINT('',(3.E0,1.5E0,-6.875E-2)); -#19443=VERTEX_POINT('',#19442); -#19444=CARTESIAN_POINT('',(3.E0,1.5E0,6.249713897704E-3)); -#19445=VERTEX_POINT('',#19444); -#19446=CARTESIAN_POINT('',(3.021276593208E0,1.5E0,1.375002861023E-1)); -#19447=VERTEX_POINT('',#19446); -#19448=CARTESIAN_POINT('',(3.063829779625E0,1.5E0,2.125E-1)); -#19449=VERTEX_POINT('',#19448); -#19450=CARTESIAN_POINT('',(3.148936152458E0,1.5E0,2.874997138977E-1)); -#19451=VERTEX_POINT('',#19450); -#19452=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,3.062502861023E-1)); -#19453=VERTEX_POINT('',#19452); -#19454=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,2.125E-1)); -#19455=VERTEX_POINT('',#19454); -#19456=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,1.749997138977E-1)); -#19457=VERTEX_POINT('',#19456); -#19458=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,1.187497138977E-1)); -#19459=VERTEX_POINT('',#19458); -#19460=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,2.500028610229E-2)); -#19461=VERTEX_POINT('',#19460); -#19462=CARTESIAN_POINT('',(3.106382966042E0,1.5E0,-5.000028610230E-2)); -#19463=VERTEX_POINT('',#19462); -#19464=CARTESIAN_POINT('',(3.127659559250E0,1.5E0,-1.437497138977E-1)); -#19465=VERTEX_POINT('',#19464); -#19466=CARTESIAN_POINT('',(3.170212745667E0,1.5E0,-1.999997138977E-1)); -#19467=VERTEX_POINT('',#19466); -#19468=CARTESIAN_POINT('',(3.234042525291E0,1.5E0,-2.375E-1)); -#19469=VERTEX_POINT('',#19468); -#19470=CARTESIAN_POINT('',(3.276595771313E0,1.5E0,-2.375E-1)); -#19471=VERTEX_POINT('',#19470); -#19472=CARTESIAN_POINT('',(3.361702144146E0,1.5E0,-1.999997138977E-1)); -#19473=VERTEX_POINT('',#19472); -#19474=CARTESIAN_POINT('',(5.75E0,1.5E0,1.03375E1)); -#19475=CARTESIAN_POINT('',(4.75E0,1.5E0,1.03375E1)); -#19476=VERTEX_POINT('',#19474); -#19477=VERTEX_POINT('',#19475); -#19478=CARTESIAN_POINT('',(4.75E0,1.5E0,1.045E1)); -#19479=VERTEX_POINT('',#19478); -#19480=CARTESIAN_POINT('',(5.75E0,1.5E0,1.045E1)); -#19481=VERTEX_POINT('',#19480); -#19482=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,9.456250035763E0)); -#19483=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,9.568749982119E0)); -#19484=VERTEX_POINT('',#19482); -#19485=VERTEX_POINT('',#19483); -#19486=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,9.587500017881E0)); -#19487=VERTEX_POINT('',#19486); -#19488=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.643750017881E0)); -#19489=VERTEX_POINT('',#19488); -#19490=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.71875E0)); -#19491=VERTEX_POINT('',#19490); -#19492=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.8875E0)); -#19493=VERTEX_POINT('',#19492); -#19494=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.962499982119E0)); -#19495=VERTEX_POINT('',#19494); -#19496=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,1.001875000894E1)); -#19497=VERTEX_POINT('',#19496); -#19498=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.005625E1)); -#19499=VERTEX_POINT('',#19498); -#19500=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,1.007500000894E1)); -#19501=VERTEX_POINT('',#19500); -#19502=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,1.007500000894E1)); -#19503=VERTEX_POINT('',#19502); -#19504=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.005625E1)); -#19505=VERTEX_POINT('',#19504); -#19506=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.001875000894E1)); -#19507=VERTEX_POINT('',#19506); -#19508=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.962499982119E0)); -#19509=VERTEX_POINT('',#19508); -#19510=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.8875E0)); -#19511=VERTEX_POINT('',#19510); -#19512=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.71875E0)); -#19513=VERTEX_POINT('',#19512); -#19514=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.643750017881E0)); -#19515=VERTEX_POINT('',#19514); -#19516=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,9.587500017881E0)); -#19517=VERTEX_POINT('',#19516); -#19518=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,9.568749982119E0)); -#19519=VERTEX_POINT('',#19518); -#19520=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,9.456250035763E0)); -#19521=VERTEX_POINT('',#19520); -#19522=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,9.474999964237E0)); -#19523=VERTEX_POINT('',#19522); -#19524=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,9.55E0)); -#19525=VERTEX_POINT('',#19524); -#19526=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.624999982119E0)); -#19527=VERTEX_POINT('',#19526); -#19528=CARTESIAN_POINT('',(4.75E0,1.5E0,9.71875E0)); -#19529=VERTEX_POINT('',#19528); -#19530=CARTESIAN_POINT('',(4.75E0,1.5E0,9.8875E0)); -#19531=VERTEX_POINT('',#19530); -#19532=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.981250017881E0)); -#19533=VERTEX_POINT('',#19532); -#19534=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.005625E1)); -#19535=VERTEX_POINT('',#19534); -#19536=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.013125000894E1)); -#19537=VERTEX_POINT('',#19536); -#19538=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.016875E1)); -#19539=VERTEX_POINT('',#19538); -#19540=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,1.018750000894E1)); -#19541=VERTEX_POINT('',#19540); -#19542=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,1.018750000894E1)); -#19543=VERTEX_POINT('',#19542); -#19544=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.016875E1)); -#19545=VERTEX_POINT('',#19544); -#19546=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.013125000894E1)); -#19547=VERTEX_POINT('',#19546); -#19548=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,1.005625E1)); -#19549=VERTEX_POINT('',#19548); -#19550=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.981250017881E0)); -#19551=VERTEX_POINT('',#19550); -#19552=CARTESIAN_POINT('',(5.75E0,1.5E0,9.8875E0)); -#19553=VERTEX_POINT('',#19552); -#19554=CARTESIAN_POINT('',(5.75E0,1.5E0,9.71875E0)); -#19555=VERTEX_POINT('',#19554); -#19556=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.624999982119E0)); -#19557=VERTEX_POINT('',#19556); -#19558=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,9.55E0)); -#19559=VERTEX_POINT('',#19558); -#19560=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.474999964237E0)); -#19561=VERTEX_POINT('',#19560); -#19562=CARTESIAN_POINT('',(5.75E0,1.5E0,9.193749964237E0)); -#19563=CARTESIAN_POINT('',(4.75E0,1.5E0,9.193749964237E0)); -#19564=VERTEX_POINT('',#19562); -#19565=VERTEX_POINT('',#19563); -#19566=CARTESIAN_POINT('',(4.75E0,1.5E0,9.306249964237E0)); -#19567=VERTEX_POINT('',#19566); -#19568=CARTESIAN_POINT('',(5.75E0,1.5E0,9.306249964237E0)); -#19569=VERTEX_POINT('',#19568); -#19570=CARTESIAN_POINT('',(4.75E0,1.5E0,8.59375E0)); -#19571=CARTESIAN_POINT('',(4.75E0,1.5E0,9.04375E0)); -#19572=VERTEX_POINT('',#19570); -#19573=VERTEX_POINT('',#19571); -#19574=CARTESIAN_POINT('',(5.75E0,1.5E0,9.04375E0)); -#19575=VERTEX_POINT('',#19574); -#19576=CARTESIAN_POINT('',(5.75E0,1.5E0,8.59375E0)); -#19577=VERTEX_POINT('',#19576); -#19578=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,8.499999928474E0)); -#19579=VERTEX_POINT('',#19578); -#19580=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,8.425E0)); -#19581=VERTEX_POINT('',#19580); -#19582=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,8.350000071526E0)); -#19583=VERTEX_POINT('',#19582); -#19584=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,8.3125E0)); -#19585=VERTEX_POINT('',#19584); -#19586=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,8.293750071526E0)); -#19587=VERTEX_POINT('',#19586); -#19588=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,8.293750071526E0)); -#19589=VERTEX_POINT('',#19588); -#19590=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,8.3125E0)); -#19591=VERTEX_POINT('',#19590); -#19592=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,8.350000071526E0)); -#19593=VERTEX_POINT('',#19592); -#19594=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,8.425E0)); -#19595=VERTEX_POINT('',#19594); -#19596=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,8.499999928474E0)); -#19597=VERTEX_POINT('',#19596); -#19598=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,8.93125E0)); -#19599=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,8.59375E0)); -#19600=VERTEX_POINT('',#19598); -#19601=VERTEX_POINT('',#19599); -#19602=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,8.518750071526E0)); -#19603=VERTEX_POINT('',#19602); -#19604=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,8.462500071526E0)); -#19605=VERTEX_POINT('',#19604); -#19606=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,8.425E0)); -#19607=VERTEX_POINT('',#19606); -#19608=CARTESIAN_POINT('',(5.090425550938E0,1.5E0,8.406250071526E0)); -#19609=VERTEX_POINT('',#19608); -#19610=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,8.406250071526E0)); -#19611=VERTEX_POINT('',#19610); -#19612=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,8.425E0)); -#19613=VERTEX_POINT('',#19612); -#19614=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,8.462500071526E0)); -#19615=VERTEX_POINT('',#19614); -#19616=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,8.518750071526E0)); -#19617=VERTEX_POINT('',#19616); -#19618=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,8.59375E0)); -#19619=VERTEX_POINT('',#19618); -#19620=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,8.93125E0)); -#19621=VERTEX_POINT('',#19620); -#19622=CARTESIAN_POINT('',(5.75E0,1.5E0,8.049999928474E0)); -#19623=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.049999928474E0)); -#19624=VERTEX_POINT('',#19622); -#19625=VERTEX_POINT('',#19623); -#19626=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.14375E0)); -#19627=VERTEX_POINT('',#19626); -#19628=CARTESIAN_POINT('',(5.75E0,1.5E0,8.14375E0)); -#19629=VERTEX_POINT('',#19628); -#19630=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,8.049999928474E0)); -#19631=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,8.049999928474E0)); -#19632=VERTEX_POINT('',#19630); -#19633=VERTEX_POINT('',#19631); -#19634=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,8.14375E0)); -#19635=VERTEX_POINT('',#19634); -#19636=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,8.14375E0)); -#19637=VERTEX_POINT('',#19636); -#19638=CARTESIAN_POINT('',(4.75E0,1.5E0,7.450000071526E0)); -#19639=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.900000071526E0)); -#19640=VERTEX_POINT('',#19638); -#19641=VERTEX_POINT('',#19639); -#19642=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.900000071526E0)); -#19643=VERTEX_POINT('',#19642); -#19644=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.450000071526E0)); -#19645=VERTEX_POINT('',#19644); -#19646=CARTESIAN_POINT('',(5.75E0,1.5E0,7.450000071526E0)); -#19647=VERTEX_POINT('',#19646); -#19648=CARTESIAN_POINT('',(5.75E0,1.5E0,7.337500071526E0)); -#19649=VERTEX_POINT('',#19648); -#19650=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.337500071526E0)); -#19651=VERTEX_POINT('',#19650); -#19652=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,7.149999928474E0)); -#19653=VERTEX_POINT('',#19652); -#19654=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.149999928474E0)); -#19655=VERTEX_POINT('',#19654); -#19656=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.337500071526E0)); -#19657=VERTEX_POINT('',#19656); -#19658=CARTESIAN_POINT('',(4.75E0,1.5E0,7.337500071526E0)); -#19659=VERTEX_POINT('',#19658); -#19660=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.768749928474E0)); -#19661=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,7.450000071526E0)); -#19662=VERTEX_POINT('',#19660); -#19663=VERTEX_POINT('',#19661); -#19664=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,7.450000071526E0)); -#19665=VERTEX_POINT('',#19664); -#19666=CARTESIAN_POINT('',(5.75E0,1.5E0,6.774999856949E0)); -#19667=CARTESIAN_POINT('',(4.75E0,1.5E0,6.774999856949E0)); -#19668=VERTEX_POINT('',#19666); -#19669=VERTEX_POINT('',#19667); -#19670=CARTESIAN_POINT('',(4.75E0,1.5E0,6.887500071526E0)); -#19671=VERTEX_POINT('',#19670); -#19672=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,7.000000071526E0)); -#19673=VERTEX_POINT('',#19672); -#19674=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,7.000000071526E0)); -#19675=VERTEX_POINT('',#19674); -#19676=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.887500071526E0)); -#19677=VERTEX_POINT('',#19676); -#19678=CARTESIAN_POINT('',(5.75E0,1.5E0,6.887500071526E0)); -#19679=VERTEX_POINT('',#19678); -#19680=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,6.625E0)); -#19681=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,6.625E0)); -#19682=VERTEX_POINT('',#19680); -#19683=VERTEX_POINT('',#19681); -#19684=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.606249856949E0)); -#19685=VERTEX_POINT('',#19684); -#19686=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,6.587500143051E0)); -#19687=VERTEX_POINT('',#19686); -#19688=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.549999856949E0)); -#19689=VERTEX_POINT('',#19688); -#19690=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,6.493749856949E0)); -#19691=VERTEX_POINT('',#19690); -#19692=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.4E0)); -#19693=VERTEX_POINT('',#19692); -#19694=CARTESIAN_POINT('',(5.75E0,1.5E0,6.2875E0)); -#19695=VERTEX_POINT('',#19694); -#19696=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.175E0)); -#19697=VERTEX_POINT('',#19696); -#19698=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,6.081250143051E0)); -#19699=VERTEX_POINT('',#19698); -#19700=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.025000143051E0)); -#19701=VERTEX_POINT('',#19700); -#19702=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.987499856949E0)); -#19703=VERTEX_POINT('',#19702); -#19704=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.968750143051E0)); -#19705=VERTEX_POINT('',#19704); -#19706=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.95E0)); -#19707=VERTEX_POINT('',#19706); -#19708=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.95E0)); -#19709=VERTEX_POINT('',#19708); -#19710=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.968750143051E0)); -#19711=VERTEX_POINT('',#19710); -#19712=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.987499856949E0)); -#19713=VERTEX_POINT('',#19712); -#19714=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,6.025000143051E0)); -#19715=VERTEX_POINT('',#19714); -#19716=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,6.081250143051E0)); -#19717=VERTEX_POINT('',#19716); -#19718=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.175E0)); -#19719=VERTEX_POINT('',#19718); -#19720=CARTESIAN_POINT('',(4.75E0,1.5E0,6.2875E0)); -#19721=VERTEX_POINT('',#19720); -#19722=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.4E0)); -#19723=VERTEX_POINT('',#19722); -#19724=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,6.493749856949E0)); -#19725=VERTEX_POINT('',#19724); -#19726=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,6.549999856949E0)); -#19727=VERTEX_POINT('',#19726); -#19728=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,6.587500143051E0)); -#19729=VERTEX_POINT('',#19728); -#19730=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.606249856949E0)); -#19731=VERTEX_POINT('',#19730); -#19732=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,6.531250143051E0)); -#19733=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.5125E0)); -#19734=VERTEX_POINT('',#19732); -#19735=VERTEX_POINT('',#19733); -#19736=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.437499856949E0)); -#19737=VERTEX_POINT('',#19736); -#19738=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.381249856949E0)); -#19739=VERTEX_POINT('',#19738); -#19740=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,6.2875E0)); -#19741=VERTEX_POINT('',#19740); -#19742=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.193750143051E0)); -#19743=VERTEX_POINT('',#19742); -#19744=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.137500143051E0)); -#19745=VERTEX_POINT('',#19744); -#19746=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,6.0625E0)); -#19747=VERTEX_POINT('',#19746); -#19748=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,6.043749856949E0)); -#19749=VERTEX_POINT('',#19748); -#19750=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,6.043749856949E0)); -#19751=VERTEX_POINT('',#19750); -#19752=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.0625E0)); -#19753=VERTEX_POINT('',#19752); -#19754=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,6.137500143051E0)); -#19755=VERTEX_POINT('',#19754); -#19756=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.193750143051E0)); -#19757=VERTEX_POINT('',#19756); -#19758=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,6.2875E0)); -#19759=VERTEX_POINT('',#19758); -#19760=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.381249856949E0)); -#19761=VERTEX_POINT('',#19760); -#19762=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,6.437499856949E0)); -#19763=VERTEX_POINT('',#19762); -#19764=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,6.5125E0)); -#19765=VERTEX_POINT('',#19764); -#19766=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,6.531250143051E0)); -#19767=VERTEX_POINT('',#19766); -#19768=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.800000143051E0)); -#19769=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.800000143051E0)); -#19770=VERTEX_POINT('',#19768); -#19771=VERTEX_POINT('',#19769); -#19772=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.78125E0)); -#19773=VERTEX_POINT('',#19772); -#19774=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.762499856949E0)); -#19775=VERTEX_POINT('',#19774); -#19776=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,5.725E0)); -#19777=VERTEX_POINT('',#19776); -#19778=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,5.66875E0)); -#19779=VERTEX_POINT('',#19778); -#19780=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,5.575000143051E0)); -#19781=VERTEX_POINT('',#19780); -#19782=CARTESIAN_POINT('',(5.75E0,1.5E0,5.462500143051E0)); -#19783=VERTEX_POINT('',#19782); -#19784=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,5.350000143051E0)); -#19785=VERTEX_POINT('',#19784); -#19786=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,5.256249856949E0)); -#19787=VERTEX_POINT('',#19786); -#19788=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,5.199999856949E0)); -#19789=VERTEX_POINT('',#19788); -#19790=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.1625E0)); -#19791=VERTEX_POINT('',#19790); -#19792=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.143749856949E0)); -#19793=VERTEX_POINT('',#19792); -#19794=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.125000143051E0)); -#19795=VERTEX_POINT('',#19794); -#19796=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,5.125000143051E0)); -#19797=VERTEX_POINT('',#19796); -#19798=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.143749856949E0)); -#19799=VERTEX_POINT('',#19798); -#19800=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.1625E0)); -#19801=VERTEX_POINT('',#19800); -#19802=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,5.199999856949E0)); -#19803=VERTEX_POINT('',#19802); -#19804=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,5.256249856949E0)); -#19805=VERTEX_POINT('',#19804); -#19806=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,5.350000143051E0)); -#19807=VERTEX_POINT('',#19806); -#19808=CARTESIAN_POINT('',(4.75E0,1.5E0,5.462500143051E0)); -#19809=VERTEX_POINT('',#19808); -#19810=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,5.575000143051E0)); -#19811=VERTEX_POINT('',#19810); -#19812=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,5.66875E0)); -#19813=VERTEX_POINT('',#19812); -#19814=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,5.725E0)); -#19815=VERTEX_POINT('',#19814); -#19816=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.762499856949E0)); -#19817=VERTEX_POINT('',#19816); -#19818=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.78125E0)); -#19819=VERTEX_POINT('',#19818); -#19820=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.706249856949E0)); -#19821=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.687500143051E0)); -#19822=VERTEX_POINT('',#19820); -#19823=VERTEX_POINT('',#19821); -#19824=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,5.6125E0)); -#19825=VERTEX_POINT('',#19824); -#19826=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,5.55625E0)); -#19827=VERTEX_POINT('',#19826); -#19828=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,5.462500143051E0)); -#19829=VERTEX_POINT('',#19828); -#19830=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,5.368749856949E0)); -#19831=VERTEX_POINT('',#19830); -#19832=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,5.312499856949E0)); -#19833=VERTEX_POINT('',#19832); -#19834=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,5.237500143051E0)); -#19835=VERTEX_POINT('',#19834); -#19836=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.21875E0)); -#19837=VERTEX_POINT('',#19836); -#19838=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,5.21875E0)); -#19839=VERTEX_POINT('',#19838); -#19840=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.237500143051E0)); -#19841=VERTEX_POINT('',#19840); -#19842=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,5.312499856949E0)); -#19843=VERTEX_POINT('',#19842); -#19844=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,5.368749856949E0)); -#19845=VERTEX_POINT('',#19844); -#19846=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,5.462500143051E0)); -#19847=VERTEX_POINT('',#19846); -#19848=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,5.55625E0)); -#19849=VERTEX_POINT('',#19848); -#19850=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,5.6125E0)); -#19851=VERTEX_POINT('',#19850); -#19852=CARTESIAN_POINT('',(5.452127665281E0,1.5E0,5.687500143051E0)); -#19853=VERTEX_POINT('',#19852); -#19854=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,5.706249856949E0)); -#19855=VERTEX_POINT('',#19854); -#19856=CARTESIAN_POINT('',(4.75E0,1.5E0,4.524999856949E0)); -#19857=CARTESIAN_POINT('',(4.75E0,1.5E0,4.675000143051E0)); -#19858=VERTEX_POINT('',#19856); -#19859=VERTEX_POINT('',#19857); -#19860=CARTESIAN_POINT('',(5.75E0,1.5E0,4.974999856949E0)); -#19861=VERTEX_POINT('',#19860); -#19862=CARTESIAN_POINT('',(5.75E0,1.5E0,4.862499856949E0)); -#19863=VERTEX_POINT('',#19862); -#19864=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,4.787500143051E0)); -#19865=VERTEX_POINT('',#19864); -#19866=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,4.412499856949E0)); -#19867=VERTEX_POINT('',#19866); -#19868=CARTESIAN_POINT('',(5.75E0,1.5E0,4.337500143051E0)); -#19869=VERTEX_POINT('',#19868); -#19870=CARTESIAN_POINT('',(5.75E0,1.5E0,4.225000143051E0)); -#19871=VERTEX_POINT('',#19870); -#19872=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,4.6E0)); -#19873=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,4.43125E0)); -#19874=VERTEX_POINT('',#19872); -#19875=VERTEX_POINT('',#19873); -#19876=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,4.76875E0)); -#19877=VERTEX_POINT('',#19876); -#19878=CARTESIAN_POINT('',(5.388297885656E0,1.5E0,3.8125E0)); -#19879=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,3.8125E0)); -#19880=VERTEX_POINT('',#19878); -#19881=VERTEX_POINT('',#19879); -#19882=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,4.074999856949E0)); -#19883=VERTEX_POINT('',#19882); -#19884=CARTESIAN_POINT('',(5.388297885656E0,1.5E0,4.074999856949E0)); -#19885=VERTEX_POINT('',#19884); -#19886=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,3.08125E0)); -#19887=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,3.043749713898E0)); -#19888=VERTEX_POINT('',#19886); -#19889=VERTEX_POINT('',#19887); -#19890=CARTESIAN_POINT('',(5.132978737354E0,1.5E0,2.987499713898E0)); -#19891=VERTEX_POINT('',#19890); -#19892=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,2.96875E0)); -#19893=VERTEX_POINT('',#19892); -#19894=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,2.96875E0)); -#19895=VERTEX_POINT('',#19894); -#19896=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,2.987499713898E0)); -#19897=VERTEX_POINT('',#19896); -#19898=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,3.043749713898E0)); -#19899=VERTEX_POINT('',#19898); -#19900=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,3.118750286102E0)); -#19901=VERTEX_POINT('',#19900); -#19902=CARTESIAN_POINT('',(4.75E0,1.5E0,3.212499713898E0)); -#19903=VERTEX_POINT('',#19902); -#19904=CARTESIAN_POINT('',(4.75E0,1.5E0,3.662500143051E0)); -#19905=VERTEX_POINT('',#19904); -#19906=CARTESIAN_POINT('',(5.75E0,1.5E0,3.662500143051E0)); -#19907=VERTEX_POINT('',#19906); -#19908=CARTESIAN_POINT('',(5.75E0,1.5E0,3.212499713898E0)); -#19909=VERTEX_POINT('',#19908); -#19910=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,3.118750286102E0)); -#19911=VERTEX_POINT('',#19910); -#19912=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,3.043749713898E0)); -#19913=VERTEX_POINT('',#19912); -#19914=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,2.987499713898E0)); -#19915=VERTEX_POINT('',#19914); -#19916=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,2.96875E0)); -#19917=VERTEX_POINT('',#19916); -#19918=CARTESIAN_POINT('',(5.409574478865E0,1.5E0,2.96875E0)); -#19919=VERTEX_POINT('',#19918); -#19920=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,2.987499713898E0)); -#19921=VERTEX_POINT('',#19920); -#19922=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,3.043749713898E0)); -#19923=VERTEX_POINT('',#19922); -#19924=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,3.550000143051E0)); -#19925=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,3.19375E0)); -#19926=VERTEX_POINT('',#19924); -#19927=VERTEX_POINT('',#19925); -#19928=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,3.1375E0)); -#19929=VERTEX_POINT('',#19928); -#19930=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,3.099999713898E0)); -#19931=VERTEX_POINT('',#19930); -#19932=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,3.08125E0)); -#19933=VERTEX_POINT('',#19932); -#19934=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,3.08125E0)); -#19935=VERTEX_POINT('',#19934); -#19936=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,3.099999713898E0)); -#19937=VERTEX_POINT('',#19936); -#19938=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,3.1375E0)); -#19939=VERTEX_POINT('',#19938); -#19940=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,3.19375E0)); -#19941=VERTEX_POINT('',#19940); -#19942=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,3.550000143051E0)); -#19943=VERTEX_POINT('',#19942); -#19944=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,3.08125E0)); -#19945=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,3.08125E0)); -#19946=VERTEX_POINT('',#19944); -#19947=VERTEX_POINT('',#19945); -#19948=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,3.099999713898E0)); -#19949=VERTEX_POINT('',#19948); -#19950=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,3.1375E0)); -#19951=VERTEX_POINT('',#19950); -#19952=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,3.19375E0)); -#19953=VERTEX_POINT('',#19952); -#19954=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,3.550000143051E0)); -#19955=VERTEX_POINT('',#19954); -#19956=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,3.550000143051E0)); -#19957=VERTEX_POINT('',#19956); -#19958=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,3.19375E0)); -#19959=VERTEX_POINT('',#19958); -#19960=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,3.1375E0)); -#19961=VERTEX_POINT('',#19960); -#19962=CARTESIAN_POINT('',(5.367021262646E0,1.5E0,3.099999713898E0)); -#19963=VERTEX_POINT('',#19962); -#19964=CARTESIAN_POINT('',(4.75E0,1.5E0,2.106250286102E0)); -#19965=CARTESIAN_POINT('',(4.75E0,1.5E0,2.818749713898E0)); -#19966=VERTEX_POINT('',#19964); -#19967=VERTEX_POINT('',#19965); -#19968=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.818749713898E0)); -#19969=VERTEX_POINT('',#19968); -#19970=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.51875E0)); -#19971=VERTEX_POINT('',#19970); -#19972=CARTESIAN_POINT('',(5.75E0,1.5E0,2.51875E0)); -#19973=VERTEX_POINT('',#19972); -#19974=CARTESIAN_POINT('',(5.75E0,1.5E0,2.40625E0)); -#19975=VERTEX_POINT('',#19974); -#19976=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.40625E0)); -#19977=VERTEX_POINT('',#19976); -#19978=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,2.106250286102E0)); -#19979=VERTEX_POINT('',#19978); -#19980=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,1.806249713898E0)); -#19981=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,1.84375E0)); -#19982=VERTEX_POINT('',#19980); -#19983=VERTEX_POINT('',#19981); -#19984=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,1.918749713898E0)); -#19985=VERTEX_POINT('',#19984); -#19986=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.95625E0)); -#19987=VERTEX_POINT('',#19986); -#19988=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.95625E0)); -#19989=VERTEX_POINT('',#19988); -#19990=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.918749713898E0)); -#19991=VERTEX_POINT('',#19990); -#19992=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,1.862499713898E0)); -#19993=VERTEX_POINT('',#19992); -#19994=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,1.768750286102E0)); -#19995=VERTEX_POINT('',#19994); -#19996=CARTESIAN_POINT('',(5.75E0,1.5E0,1.675E0)); -#19997=VERTEX_POINT('',#19996); -#19998=CARTESIAN_POINT('',(5.75E0,1.5E0,1.5625E0)); -#19999=VERTEX_POINT('',#19998); -#20000=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,1.468749713898E0)); -#20001=VERTEX_POINT('',#20000); -#20002=CARTESIAN_POINT('',(5.664893619716E0,1.5E0,1.375000286102E0)); -#20003=VERTEX_POINT('',#20002); -#20004=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,1.318750286102E0)); -#20005=VERTEX_POINT('',#20004); -#20006=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.28125E0)); -#20007=VERTEX_POINT('',#20006); -#20008=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.28125E0)); -#20009=VERTEX_POINT('',#20008); -#20010=CARTESIAN_POINT('',(5.324468076229E0,1.5E0,1.318750286102E0)); -#20011=VERTEX_POINT('',#20010); -#20012=CARTESIAN_POINT('',(5.260638296604E0,1.5E0,1.39375E0)); -#20013=VERTEX_POINT('',#20012); -#20014=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,1.431250286102E0)); -#20015=VERTEX_POINT('',#20014); -#20016=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,1.39375E0)); -#20017=VERTEX_POINT('',#20016); -#20018=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,1.3375E0)); -#20019=VERTEX_POINT('',#20018); -#20020=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,1.299999713898E0)); -#20021=VERTEX_POINT('',#20020); -#20022=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.299999713898E0)); -#20023=VERTEX_POINT('',#20022); -#20024=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.3375E0)); -#20025=VERTEX_POINT('',#20024); -#20026=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,1.39375E0)); -#20027=VERTEX_POINT('',#20026); -#20028=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.487500286102E0)); -#20029=VERTEX_POINT('',#20028); -#20030=CARTESIAN_POINT('',(4.75E0,1.5E0,1.581249713898E0)); -#20031=VERTEX_POINT('',#20030); -#20032=CARTESIAN_POINT('',(4.75E0,1.5E0,1.656250286102E0)); -#20033=VERTEX_POINT('',#20032); -#20034=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.749999713898E0)); -#20035=VERTEX_POINT('',#20034); -#20036=CARTESIAN_POINT('',(4.835106372833E0,1.5E0,1.84375E0)); -#20037=VERTEX_POINT('',#20036); -#20038=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.9E0)); -#20039=VERTEX_POINT('',#20038); -#20040=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.937500286102E0)); -#20041=VERTEX_POINT('',#20040); -#20042=CARTESIAN_POINT('',(5.069148957729E0,1.5E0,1.937500286102E0)); -#20043=VERTEX_POINT('',#20042); -#20044=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,1.9E0)); -#20045=VERTEX_POINT('',#20044); -#20046=CARTESIAN_POINT('',(5.218085110188E0,1.5E0,1.84375E0)); -#20047=VERTEX_POINT('',#20046); -#20048=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.656250286102E0)); -#20049=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,1.73125E0)); -#20050=VERTEX_POINT('',#20048); -#20051=VERTEX_POINT('',#20049); -#20052=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.806249713898E0)); -#20053=VERTEX_POINT('',#20052); -#20054=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.862499713898E0)); -#20055=VERTEX_POINT('',#20054); -#20056=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.862499713898E0)); -#20057=VERTEX_POINT('',#20056); -#20058=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,1.806249713898E0)); -#20059=VERTEX_POINT('',#20058); -#20060=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,1.73125E0)); -#20061=VERTEX_POINT('',#20060); -#20062=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,1.656250286102E0)); -#20063=VERTEX_POINT('',#20062); -#20064=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,1.581249713898E0)); -#20065=VERTEX_POINT('',#20064); -#20066=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,1.50625E0)); -#20067=VERTEX_POINT('',#20066); -#20068=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,1.431250286102E0)); -#20069=VERTEX_POINT('',#20068); -#20070=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,1.375000286102E0)); -#20071=VERTEX_POINT('',#20070); -#20072=CARTESIAN_POINT('',(5.494680851698E0,1.5E0,1.375000286102E0)); -#20073=VERTEX_POINT('',#20072); -#20074=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.431250286102E0)); -#20075=VERTEX_POINT('',#20074); -#20076=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,1.50625E0)); -#20077=VERTEX_POINT('',#20076); -#20078=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.581249713898E0)); -#20079=VERTEX_POINT('',#20078); -#20080=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,1.581249713898E0)); -#20081=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.50625E0)); -#20082=VERTEX_POINT('',#20080); -#20083=VERTEX_POINT('',#20081); -#20084=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.431250286102E0)); -#20085=VERTEX_POINT('',#20084); -#20086=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.39375E0)); -#20087=VERTEX_POINT('',#20086); -#20088=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,1.39375E0)); -#20089=VERTEX_POINT('',#20088); -#20090=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,1.431250286102E0)); -#20091=VERTEX_POINT('',#20090); -#20092=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,1.50625E0)); -#20093=VERTEX_POINT('',#20092); -#20094=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,1.581249713898E0)); -#20095=VERTEX_POINT('',#20094); -#20096=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,1.656250286102E0)); -#20097=VERTEX_POINT('',#20096); -#20098=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,1.73125E0)); -#20099=VERTEX_POINT('',#20098); -#20100=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,1.806249713898E0)); -#20101=VERTEX_POINT('',#20100); -#20102=CARTESIAN_POINT('',(5.047872364521E0,1.5E0,1.84375E0)); -#20103=VERTEX_POINT('',#20102); -#20104=CARTESIAN_POINT('',(5.005319178104E0,1.5E0,1.84375E0)); -#20105=VERTEX_POINT('',#20104); -#20106=CARTESIAN_POINT('',(4.941489338875E0,1.5E0,1.806249713898E0)); -#20107=VERTEX_POINT('',#20106); -#20108=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.73125E0)); -#20109=VERTEX_POINT('',#20108); -#20110=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,1.656250286102E0)); -#20111=VERTEX_POINT('',#20110); -#20112=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,5.124997138977E-1)); -#20113=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,4.750002861023E-1)); -#20114=VERTEX_POINT('',#20112); -#20115=VERTEX_POINT('',#20113); -#20116=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,4.562497138977E-1)); -#20117=VERTEX_POINT('',#20116); -#20118=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,4.562497138977E-1)); -#20119=VERTEX_POINT('',#20118); -#20120=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,4.750002861023E-1)); -#20121=VERTEX_POINT('',#20120); -#20122=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,5.124997138977E-1)); -#20123=VERTEX_POINT('',#20122); -#20124=CARTESIAN_POINT('',(5.239361703396E0,1.5E0,6.0625E-1)); -#20125=VERTEX_POINT('',#20124); -#20126=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,5.312502861023E-1)); -#20127=VERTEX_POINT('',#20126); -#20128=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,4.9375E-1)); -#20129=VERTEX_POINT('',#20128); -#20130=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,4.750002861023E-1)); -#20131=VERTEX_POINT('',#20130); -#20132=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,4.750002861023E-1)); -#20133=VERTEX_POINT('',#20132); -#20134=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,4.9375E-1)); -#20135=VERTEX_POINT('',#20134); -#20136=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,5.687497138977E-1)); -#20137=VERTEX_POINT('',#20136); -#20138=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,6.437502861023E-1)); -#20139=VERTEX_POINT('',#20138); -#20140=CARTESIAN_POINT('',(4.75E0,1.5E0,7.75E-1)); -#20141=VERTEX_POINT('',#20140); -#20142=CARTESIAN_POINT('',(4.75E0,1.5E0,8.125002861023E-1)); -#20143=VERTEX_POINT('',#20142); -#20144=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,9.4375E-1)); -#20145=VERTEX_POINT('',#20144); -#20146=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.018749713898E0)); -#20147=VERTEX_POINT('',#20146); -#20148=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,1.093750286102E0)); -#20149=VERTEX_POINT('',#20148); -#20150=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.1125E0)); -#20151=VERTEX_POINT('',#20150); -#20152=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.018749713898E0)); -#20153=VERTEX_POINT('',#20152); -#20154=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,9.812502861023E-1)); -#20155=VERTEX_POINT('',#20154); -#20156=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,9.250002861023E-1)); -#20157=VERTEX_POINT('',#20156); -#20158=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,8.3125E-1)); -#20159=VERTEX_POINT('',#20158); -#20160=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,7.562502861023E-1)); -#20161=VERTEX_POINT('',#20160); -#20162=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,6.625E-1)); -#20163=VERTEX_POINT('',#20162); -#20164=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,6.0625E-1)); -#20165=VERTEX_POINT('',#20164); -#20166=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,5.687497138977E-1)); -#20167=VERTEX_POINT('',#20166); -#20168=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,5.687497138977E-1)); -#20169=VERTEX_POINT('',#20168); -#20170=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,6.0625E-1)); -#20171=VERTEX_POINT('',#20170); -#20172=CARTESIAN_POINT('',(5.154255330563E0,1.5E0,6.437502861023E-1)); -#20173=VERTEX_POINT('',#20172); -#20174=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,7.562502861023E-1)); -#20175=VERTEX_POINT('',#20174); -#20176=CARTESIAN_POINT('',(5.196808516979E0,1.5E0,8.3125E-1)); -#20177=VERTEX_POINT('',#20176); -#20178=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,8.3125E-1)); -#20179=VERTEX_POINT('',#20178); -#20180=CARTESIAN_POINT('',(5.281914889812E0,1.5E0,7.562502861023E-1)); -#20181=VERTEX_POINT('',#20180); -#20182=CARTESIAN_POINT('',(5.303191483021E0,1.5E0,6.437502861023E-1)); -#20183=VERTEX_POINT('',#20182); -#20184=CARTESIAN_POINT('',(5.345744669437E0,1.5E0,5.875002861023E-1)); -#20185=VERTEX_POINT('',#20184); -#20186=CARTESIAN_POINT('',(5.430851072073E0,1.5E0,5.5E-1)); -#20187=VERTEX_POINT('',#20186); -#20188=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,5.5E-1)); -#20189=VERTEX_POINT('',#20188); -#20190=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,5.687497138977E-1)); -#20191=VERTEX_POINT('',#20190); -#20192=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,6.0625E-1)); -#20193=VERTEX_POINT('',#20192); -#20194=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,6.437502861023E-1)); -#20195=VERTEX_POINT('',#20194); -#20196=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,7.374997138977E-1)); -#20197=VERTEX_POINT('',#20196); -#20198=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,8.499997138977E-1)); -#20199=VERTEX_POINT('',#20198); -#20200=CARTESIAN_POINT('',(5.622340425849E0,1.5E0,9.4375E-1)); -#20201=VERTEX_POINT('',#20200); -#20202=CARTESIAN_POINT('',(5.601063832641E0,1.5E0,9.812502861023E-1)); -#20203=VERTEX_POINT('',#20202); -#20204=CARTESIAN_POINT('',(5.558510631323E0,1.5E0,1.018749713898E0)); -#20205=VERTEX_POINT('',#20204); -#20206=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.037500286102E0)); -#20207=VERTEX_POINT('',#20206); -#20208=CARTESIAN_POINT('',(5.515957444906E0,1.5E0,1.131249713898E0)); -#20209=VERTEX_POINT('',#20208); -#20210=CARTESIAN_POINT('',(5.579787239432E0,1.5E0,1.1125E0)); -#20211=VERTEX_POINT('',#20210); -#20212=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.074999713898E0)); -#20213=VERTEX_POINT('',#20212); -#20214=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,1.018749713898E0)); -#20215=VERTEX_POINT('',#20214); -#20216=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,9.4375E-1)); -#20217=VERTEX_POINT('',#20216); -#20218=CARTESIAN_POINT('',(5.75E0,1.5E0,8.687502861023E-1)); -#20219=VERTEX_POINT('',#20218); -#20220=CARTESIAN_POINT('',(5.75E0,1.5E0,7.1875E-1)); -#20221=VERTEX_POINT('',#20220); -#20222=CARTESIAN_POINT('',(5.728723404929E0,1.5E0,6.437502861023E-1)); -#20223=VERTEX_POINT('',#20222); -#20224=CARTESIAN_POINT('',(5.686170212924E0,1.5E0,5.687497138977E-1)); -#20225=VERTEX_POINT('',#20224); -#20226=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,3.062502861023E-1)); -#20227=CARTESIAN_POINT('',(5.75E0,1.5E0,3.062502861023E-1)); -#20228=VERTEX_POINT('',#20226); -#20229=VERTEX_POINT('',#20227); -#20230=CARTESIAN_POINT('',(5.75E0,1.5E0,-3.687497138977E-1)); -#20231=VERTEX_POINT('',#20230); -#20232=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,-3.687497138977E-1)); -#20233=VERTEX_POINT('',#20232); -#20234=CARTESIAN_POINT('',(5.643617019057E0,1.5E0,1.5625E-1)); -#20235=VERTEX_POINT('',#20234); -#20236=CARTESIAN_POINT('',(5.175531923771E0,1.5E0,-3.124997138977E-1)); -#20237=VERTEX_POINT('',#20236); -#20238=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,-3.5E-1)); -#20239=VERTEX_POINT('',#20238); -#20240=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,-3.687497138977E-1)); -#20241=VERTEX_POINT('',#20240); -#20242=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,-3.687497138977E-1)); -#20243=VERTEX_POINT('',#20242); -#20244=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,-3.5E-1)); -#20245=VERTEX_POINT('',#20244); -#20246=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,-2.750002861023E-1)); -#20247=VERTEX_POINT('',#20246); -#20248=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,-1.999997138977E-1)); -#20249=VERTEX_POINT('',#20248); -#20250=CARTESIAN_POINT('',(4.75E0,1.5E0,-8.749971389771E-2)); -#20251=VERTEX_POINT('',#20250); -#20252=CARTESIAN_POINT('',(4.75E0,1.5E0,-1.25E-2)); -#20253=VERTEX_POINT('',#20252); -#20254=CARTESIAN_POINT('',(4.771276593208E0,1.5E0,1.187497138977E-1)); -#20255=VERTEX_POINT('',#20254); -#20256=CARTESIAN_POINT('',(4.813829779625E0,1.5E0,1.937502861023E-1)); -#20257=VERTEX_POINT('',#20256); -#20258=CARTESIAN_POINT('',(4.898936152458E0,1.5E0,2.6875E-1)); -#20259=VERTEX_POINT('',#20258); -#20260=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,2.874997138977E-1)); -#20261=VERTEX_POINT('',#20260); -#20262=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,1.937502861023E-1)); -#20263=VERTEX_POINT('',#20262); -#20264=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,1.5625E-1)); -#20265=VERTEX_POINT('',#20264); -#20266=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,1.E-1)); -#20267=VERTEX_POINT('',#20266); -#20268=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,6.249713897704E-3)); -#20269=VERTEX_POINT('',#20268); -#20270=CARTESIAN_POINT('',(4.856382966042E0,1.5E0,-6.875E-2)); -#20271=VERTEX_POINT('',#20270); -#20272=CARTESIAN_POINT('',(4.877659559250E0,1.5E0,-1.625002861023E-1)); -#20273=VERTEX_POINT('',#20272); -#20274=CARTESIAN_POINT('',(4.920212745667E0,1.5E0,-2.187502861023E-1)); -#20275=VERTEX_POINT('',#20274); -#20276=CARTESIAN_POINT('',(4.984042525291E0,1.5E0,-2.562497138977E-1)); -#20277=VERTEX_POINT('',#20276); -#20278=CARTESIAN_POINT('',(5.026595771313E0,1.5E0,-2.562497138977E-1)); -#20279=VERTEX_POINT('',#20278); -#20280=CARTESIAN_POINT('',(5.111702144146E0,1.5E0,-2.187502861023E-1)); -#20281=VERTEX_POINT('',#20280); -#20282=CARTESIAN_POINT('',(4.E0,1.55E0,1.03375E1)); -#20283=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.03375E1)); -#20284=VERTEX_POINT('',#20282); -#20285=VERTEX_POINT('',#20283); -#20286=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,9.849999982119E0)); -#20287=VERTEX_POINT('',#20286); -#20288=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,9.849999982119E0)); -#20289=VERTEX_POINT('',#20288); -#20290=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.03375E1)); -#20291=VERTEX_POINT('',#20290); -#20292=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.03375E1)); -#20293=VERTEX_POINT('',#20292); -#20294=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.775E0)); -#20295=VERTEX_POINT('',#20294); -#20296=CARTESIAN_POINT('',(3.E0,1.55E0,9.775E0)); -#20297=VERTEX_POINT('',#20296); -#20298=CARTESIAN_POINT('',(3.E0,1.55E0,1.045E1)); -#20299=VERTEX_POINT('',#20298); -#20300=CARTESIAN_POINT('',(4.E0,1.55E0,1.045E1)); -#20301=VERTEX_POINT('',#20300); -#20302=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.893750035763E0)); -#20303=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.006250035763E0)); -#20304=VERTEX_POINT('',#20302); -#20305=VERTEX_POINT('',#20303); -#20306=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.024999964237E0)); -#20307=VERTEX_POINT('',#20306); -#20308=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.081249964237E0)); -#20309=VERTEX_POINT('',#20308); -#20310=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.15625E0)); -#20311=VERTEX_POINT('',#20310); -#20312=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.325E0)); -#20313=VERTEX_POINT('',#20312); -#20314=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.400000035763E0)); -#20315=VERTEX_POINT('',#20314); -#20316=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.456250035763E0)); -#20317=VERTEX_POINT('',#20316); -#20318=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.49375E0)); -#20319=VERTEX_POINT('',#20318); -#20320=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.512500035763E0)); -#20321=VERTEX_POINT('',#20320); -#20322=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.512500035763E0)); -#20323=VERTEX_POINT('',#20322); -#20324=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.49375E0)); -#20325=VERTEX_POINT('',#20324); -#20326=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.456250035763E0)); -#20327=VERTEX_POINT('',#20326); -#20328=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.400000035763E0)); -#20329=VERTEX_POINT('',#20328); -#20330=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.325E0)); -#20331=VERTEX_POINT('',#20330); -#20332=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.15625E0)); -#20333=VERTEX_POINT('',#20332); -#20334=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.081249964237E0)); -#20335=VERTEX_POINT('',#20334); -#20336=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.024999964237E0)); -#20337=VERTEX_POINT('',#20336); -#20338=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.006250035763E0)); -#20339=VERTEX_POINT('',#20338); -#20340=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.893750035763E0)); -#20341=VERTEX_POINT('',#20340); -#20342=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.912499964237E0)); -#20343=VERTEX_POINT('',#20342); -#20344=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.9875E0)); -#20345=VERTEX_POINT('',#20344); -#20346=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.062500035763E0)); -#20347=VERTEX_POINT('',#20346); -#20348=CARTESIAN_POINT('',(3.E0,1.55E0,9.15625E0)); -#20349=VERTEX_POINT('',#20348); -#20350=CARTESIAN_POINT('',(3.E0,1.55E0,9.325E0)); -#20351=VERTEX_POINT('',#20350); -#20352=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.418749964237E0)); -#20353=VERTEX_POINT('',#20352); -#20354=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,9.49375E0)); -#20355=VERTEX_POINT('',#20354); -#20356=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.568749982119E0)); -#20357=VERTEX_POINT('',#20356); -#20358=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,9.60625E0)); -#20359=VERTEX_POINT('',#20358); -#20360=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.624999982119E0)); -#20361=VERTEX_POINT('',#20360); -#20362=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.624999982119E0)); -#20363=VERTEX_POINT('',#20362); -#20364=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,9.60625E0)); -#20365=VERTEX_POINT('',#20364); -#20366=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.568749982119E0)); -#20367=VERTEX_POINT('',#20366); -#20368=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,9.49375E0)); -#20369=VERTEX_POINT('',#20368); -#20370=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.418749964237E0)); -#20371=VERTEX_POINT('',#20370); -#20372=CARTESIAN_POINT('',(4.E0,1.55E0,9.325E0)); -#20373=VERTEX_POINT('',#20372); -#20374=CARTESIAN_POINT('',(4.E0,1.55E0,9.15625E0)); -#20375=VERTEX_POINT('',#20374); -#20376=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.062500035763E0)); -#20377=VERTEX_POINT('',#20376); -#20378=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.9875E0)); -#20379=VERTEX_POINT('',#20378); -#20380=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.912499964237E0)); -#20381=VERTEX_POINT('',#20380); -#20382=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.012500071526E0)); -#20383=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.125000071526E0)); -#20384=VERTEX_POINT('',#20382); -#20385=VERTEX_POINT('',#20383); -#20386=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.14375E0)); -#20387=VERTEX_POINT('',#20386); -#20388=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.2E0)); -#20389=VERTEX_POINT('',#20388); -#20390=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.274999928474E0)); -#20391=VERTEX_POINT('',#20390); -#20392=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.443749928474E0)); -#20393=VERTEX_POINT('',#20392); -#20394=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.518750071526E0)); -#20395=VERTEX_POINT('',#20394); -#20396=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.575000071526E0)); -#20397=VERTEX_POINT('',#20396); -#20398=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.612499928474E0)); -#20399=VERTEX_POINT('',#20398); -#20400=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.631250071526E0)); -#20401=VERTEX_POINT('',#20400); -#20402=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.631250071526E0)); -#20403=VERTEX_POINT('',#20402); -#20404=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.612499928474E0)); -#20405=VERTEX_POINT('',#20404); -#20406=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.575000071526E0)); -#20407=VERTEX_POINT('',#20406); -#20408=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.518750071526E0)); -#20409=VERTEX_POINT('',#20408); -#20410=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.443749928474E0)); -#20411=VERTEX_POINT('',#20410); -#20412=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.274999928474E0)); -#20413=VERTEX_POINT('',#20412); -#20414=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.2E0)); -#20415=VERTEX_POINT('',#20414); -#20416=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.14375E0)); -#20417=VERTEX_POINT('',#20416); -#20418=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.125000071526E0)); -#20419=VERTEX_POINT('',#20418); -#20420=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.012500071526E0)); -#20421=VERTEX_POINT('',#20420); -#20422=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.03125E0)); -#20423=VERTEX_POINT('',#20422); -#20424=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.106249928474E0)); -#20425=VERTEX_POINT('',#20424); -#20426=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.181250071526E0)); -#20427=VERTEX_POINT('',#20426); -#20428=CARTESIAN_POINT('',(3.E0,1.55E0,8.274999928474E0)); -#20429=VERTEX_POINT('',#20428); -#20430=CARTESIAN_POINT('',(3.E0,1.55E0,8.443749928474E0)); -#20431=VERTEX_POINT('',#20430); -#20432=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.5375E0)); -#20433=VERTEX_POINT('',#20432); -#20434=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.612499928474E0)); -#20435=VERTEX_POINT('',#20434); -#20436=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.687499964237E0)); -#20437=VERTEX_POINT('',#20436); -#20438=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,8.725000035763E0)); -#20439=VERTEX_POINT('',#20438); -#20440=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.743749964237E0)); -#20441=VERTEX_POINT('',#20440); -#20442=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.743749964237E0)); -#20443=VERTEX_POINT('',#20442); -#20444=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,8.725000035763E0)); -#20445=VERTEX_POINT('',#20444); -#20446=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.687499964237E0)); -#20447=VERTEX_POINT('',#20446); -#20448=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.612499928474E0)); -#20449=VERTEX_POINT('',#20448); -#20450=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.5375E0)); -#20451=VERTEX_POINT('',#20450); -#20452=CARTESIAN_POINT('',(4.E0,1.55E0,8.443749928474E0)); -#20453=VERTEX_POINT('',#20452); -#20454=CARTESIAN_POINT('',(4.E0,1.55E0,8.274999928474E0)); -#20455=VERTEX_POINT('',#20454); -#20456=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.181250071526E0)); -#20457=VERTEX_POINT('',#20456); -#20458=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.106249928474E0)); -#20459=VERTEX_POINT('',#20458); -#20460=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.03125E0)); -#20461=VERTEX_POINT('',#20460); -#20462=CARTESIAN_POINT('',(4.E0,1.55E0,7.75E0)); -#20463=CARTESIAN_POINT('',(3.E0,1.55E0,7.75E0)); -#20464=VERTEX_POINT('',#20462); -#20465=VERTEX_POINT('',#20463); -#20466=CARTESIAN_POINT('',(3.E0,1.55E0,7.8625E0)); -#20467=VERTEX_POINT('',#20466); -#20468=CARTESIAN_POINT('',(4.E0,1.55E0,7.8625E0)); -#20469=VERTEX_POINT('',#20468); -#20470=CARTESIAN_POINT('',(3.E0,1.55E0,7.149999928474E0)); -#20471=CARTESIAN_POINT('',(3.E0,1.55E0,7.599999928474E0)); -#20472=VERTEX_POINT('',#20470); -#20473=VERTEX_POINT('',#20471); -#20474=CARTESIAN_POINT('',(4.E0,1.55E0,7.599999928474E0)); -#20475=VERTEX_POINT('',#20474); -#20476=CARTESIAN_POINT('',(4.E0,1.55E0,7.149999928474E0)); -#20477=VERTEX_POINT('',#20476); -#20478=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,7.056250071526E0)); -#20479=VERTEX_POINT('',#20478); -#20480=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,6.981249928474E0)); -#20481=VERTEX_POINT('',#20480); -#20482=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.90625E0)); -#20483=VERTEX_POINT('',#20482); -#20484=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,6.868749928474E0)); -#20485=VERTEX_POINT('',#20484); -#20486=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.85E0)); -#20487=VERTEX_POINT('',#20486); -#20488=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.85E0)); -#20489=VERTEX_POINT('',#20488); -#20490=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,6.868749928474E0)); -#20491=VERTEX_POINT('',#20490); -#20492=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,6.90625E0)); -#20493=VERTEX_POINT('',#20492); -#20494=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,6.981249928474E0)); -#20495=VERTEX_POINT('',#20494); -#20496=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,7.056250071526E0)); -#20497=VERTEX_POINT('',#20496); -#20498=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.487499928474E0)); -#20499=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.149999928474E0)); -#20500=VERTEX_POINT('',#20498); -#20501=VERTEX_POINT('',#20499); -#20502=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,7.075E0)); -#20503=VERTEX_POINT('',#20502); -#20504=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,7.01875E0)); -#20505=VERTEX_POINT('',#20504); -#20506=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,6.981249928474E0)); -#20507=VERTEX_POINT('',#20506); -#20508=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.9625E0)); -#20509=VERTEX_POINT('',#20508); -#20510=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.9625E0)); -#20511=VERTEX_POINT('',#20510); -#20512=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,6.981249928474E0)); -#20513=VERTEX_POINT('',#20512); -#20514=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,7.01875E0)); -#20515=VERTEX_POINT('',#20514); -#20516=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,7.075E0)); -#20517=VERTEX_POINT('',#20516); -#20518=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.149999928474E0)); -#20519=VERTEX_POINT('',#20518); -#20520=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.487499928474E0)); -#20521=VERTEX_POINT('',#20520); -#20522=CARTESIAN_POINT('',(4.E0,1.55E0,6.606249856949E0)); -#20523=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.606249856949E0)); -#20524=VERTEX_POINT('',#20522); -#20525=VERTEX_POINT('',#20523); -#20526=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.700000143051E0)); -#20527=VERTEX_POINT('',#20526); -#20528=CARTESIAN_POINT('',(4.E0,1.55E0,6.700000143051E0)); -#20529=VERTEX_POINT('',#20528); -#20530=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.606249856949E0)); -#20531=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.606249856949E0)); -#20532=VERTEX_POINT('',#20530); -#20533=VERTEX_POINT('',#20531); -#20534=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.700000143051E0)); -#20535=VERTEX_POINT('',#20534); -#20536=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.700000143051E0)); -#20537=VERTEX_POINT('',#20536); -#20538=CARTESIAN_POINT('',(4.E0,1.55E0,5.818749856949E0)); -#20539=CARTESIAN_POINT('',(4.E0,1.55E0,5.706249856949E0)); -#20540=VERTEX_POINT('',#20538); -#20541=VERTEX_POINT('',#20539); -#20542=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.025000143051E0)); -#20543=VERTEX_POINT('',#20542); -#20544=CARTESIAN_POINT('',(3.E0,1.55E0,5.706249856949E0)); -#20545=VERTEX_POINT('',#20544); -#20546=CARTESIAN_POINT('',(3.E0,1.55E0,5.818749856949E0)); -#20547=VERTEX_POINT('',#20546); -#20548=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.081250143051E0)); -#20549=VERTEX_POINT('',#20548); -#20550=CARTESIAN_POINT('',(3.E0,1.55E0,6.34375E0)); -#20551=VERTEX_POINT('',#20550); -#20552=CARTESIAN_POINT('',(3.E0,1.55E0,6.45625E0)); -#20553=VERTEX_POINT('',#20552); -#20554=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.137500143051E0)); -#20555=VERTEX_POINT('',#20554); -#20556=CARTESIAN_POINT('',(4.E0,1.55E0,6.45625E0)); -#20557=VERTEX_POINT('',#20556); -#20558=CARTESIAN_POINT('',(4.E0,1.55E0,6.34375E0)); -#20559=VERTEX_POINT('',#20558); -#20560=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.081250143051E0)); -#20561=VERTEX_POINT('',#20560); -#20562=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.406250143051E0)); -#20563=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,5.44375E0)); -#20564=VERTEX_POINT('',#20562); -#20565=VERTEX_POINT('',#20563); -#20566=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,5.518750143051E0)); -#20567=VERTEX_POINT('',#20566); -#20568=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.55625E0)); -#20569=VERTEX_POINT('',#20568); -#20570=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.55625E0)); -#20571=VERTEX_POINT('',#20570); -#20572=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,5.518750143051E0)); -#20573=VERTEX_POINT('',#20572); -#20574=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,5.462500143051E0)); -#20575=VERTEX_POINT('',#20574); -#20576=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.368749856949E0)); -#20577=VERTEX_POINT('',#20576); -#20578=CARTESIAN_POINT('',(4.E0,1.55E0,5.275E0)); -#20579=VERTEX_POINT('',#20578); -#20580=CARTESIAN_POINT('',(4.E0,1.55E0,5.1625E0)); -#20581=VERTEX_POINT('',#20580); -#20582=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.068750143051E0)); -#20583=VERTEX_POINT('',#20582); -#20584=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,4.974999856949E0)); -#20585=VERTEX_POINT('',#20584); -#20586=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,4.918749856949E0)); -#20587=VERTEX_POINT('',#20586); -#20588=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.88125E0)); -#20589=VERTEX_POINT('',#20588); -#20590=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.88125E0)); -#20591=VERTEX_POINT('',#20590); -#20592=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,4.918749856949E0)); -#20593=VERTEX_POINT('',#20592); -#20594=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,4.99375E0)); -#20595=VERTEX_POINT('',#20594); -#20596=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.031249856949E0)); -#20597=VERTEX_POINT('',#20596); -#20598=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,4.99375E0)); -#20599=VERTEX_POINT('',#20598); -#20600=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,4.9375E0)); -#20601=VERTEX_POINT('',#20600); -#20602=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,4.900000143051E0)); -#20603=VERTEX_POINT('',#20602); -#20604=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.900000143051E0)); -#20605=VERTEX_POINT('',#20604); -#20606=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,4.9375E0)); -#20607=VERTEX_POINT('',#20606); -#20608=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,4.99375E0)); -#20609=VERTEX_POINT('',#20608); -#20610=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.087499856949E0)); -#20611=VERTEX_POINT('',#20610); -#20612=CARTESIAN_POINT('',(3.E0,1.55E0,5.181250143051E0)); -#20613=VERTEX_POINT('',#20612); -#20614=CARTESIAN_POINT('',(3.E0,1.55E0,5.256249856949E0)); -#20615=VERTEX_POINT('',#20614); -#20616=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.350000143051E0)); -#20617=VERTEX_POINT('',#20616); -#20618=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,5.44375E0)); -#20619=VERTEX_POINT('',#20618); -#20620=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.5E0)); -#20621=VERTEX_POINT('',#20620); -#20622=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.537499856949E0)); -#20623=VERTEX_POINT('',#20622); -#20624=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,5.537499856949E0)); -#20625=VERTEX_POINT('',#20624); -#20626=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,5.5E0)); -#20627=VERTEX_POINT('',#20626); -#20628=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,5.44375E0)); -#20629=VERTEX_POINT('',#20628); -#20630=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.256249856949E0)); -#20631=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.33125E0)); -#20632=VERTEX_POINT('',#20630); -#20633=VERTEX_POINT('',#20631); -#20634=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.406250143051E0)); -#20635=VERTEX_POINT('',#20634); -#20636=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.462500143051E0)); -#20637=VERTEX_POINT('',#20636); -#20638=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.462500143051E0)); -#20639=VERTEX_POINT('',#20638); -#20640=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.406250143051E0)); -#20641=VERTEX_POINT('',#20640); -#20642=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.33125E0)); -#20643=VERTEX_POINT('',#20642); -#20644=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.256249856949E0)); -#20645=VERTEX_POINT('',#20644); -#20646=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.181250143051E0)); -#20647=VERTEX_POINT('',#20646); -#20648=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.10625E0)); -#20649=VERTEX_POINT('',#20648); -#20650=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.031249856949E0)); -#20651=VERTEX_POINT('',#20650); -#20652=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.974999856949E0)); -#20653=VERTEX_POINT('',#20652); -#20654=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.974999856949E0)); -#20655=VERTEX_POINT('',#20654); -#20656=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.031249856949E0)); -#20657=VERTEX_POINT('',#20656); -#20658=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.10625E0)); -#20659=VERTEX_POINT('',#20658); -#20660=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.181250143051E0)); -#20661=VERTEX_POINT('',#20660); -#20662=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.181250143051E0)); -#20663=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.10625E0)); -#20664=VERTEX_POINT('',#20662); -#20665=VERTEX_POINT('',#20663); -#20666=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.031249856949E0)); -#20667=VERTEX_POINT('',#20666); -#20668=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.99375E0)); -#20669=VERTEX_POINT('',#20668); -#20670=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,4.99375E0)); -#20671=VERTEX_POINT('',#20670); -#20672=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.031249856949E0)); -#20673=VERTEX_POINT('',#20672); -#20674=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.10625E0)); -#20675=VERTEX_POINT('',#20674); -#20676=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.181250143051E0)); -#20677=VERTEX_POINT('',#20676); -#20678=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.256249856949E0)); -#20679=VERTEX_POINT('',#20678); -#20680=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.33125E0)); -#20681=VERTEX_POINT('',#20680); -#20682=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.406250143051E0)); -#20683=VERTEX_POINT('',#20682); -#20684=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,5.44375E0)); -#20685=VERTEX_POINT('',#20684); -#20686=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.44375E0)); -#20687=VERTEX_POINT('',#20686); -#20688=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.406250143051E0)); -#20689=VERTEX_POINT('',#20688); -#20690=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.33125E0)); -#20691=VERTEX_POINT('',#20690); -#20692=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.256249856949E0)); -#20693=VERTEX_POINT('',#20692); -#20694=CARTESIAN_POINT('',(4.E0,1.55E0,4.43125E0)); -#20695=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,4.281250143051E0)); -#20696=VERTEX_POINT('',#20694); -#20697=VERTEX_POINT('',#20695); -#20698=CARTESIAN_POINT('',(4.E0,1.55E0,4.131249856949E0)); -#20699=VERTEX_POINT('',#20698); -#20700=CARTESIAN_POINT('',(4.E0,1.55E0,3.98125E0)); -#20701=VERTEX_POINT('',#20700); -#20702=CARTESIAN_POINT('',(3.E0,1.55E0,3.831250143051E0)); -#20703=VERTEX_POINT('',#20702); -#20704=CARTESIAN_POINT('',(3.E0,1.55E0,3.943750143051E0)); -#20705=VERTEX_POINT('',#20704); -#20706=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.056250143051E0)); -#20707=VERTEX_POINT('',#20706); -#20708=CARTESIAN_POINT('',(3.E0,1.55E0,4.20625E0)); -#20709=VERTEX_POINT('',#20708); -#20710=CARTESIAN_POINT('',(3.E0,1.55E0,4.356249856949E0)); -#20711=VERTEX_POINT('',#20710); -#20712=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.506250143051E0)); -#20713=VERTEX_POINT('',#20712); -#20714=CARTESIAN_POINT('',(3.E0,1.55E0,4.618750143051E0)); -#20715=VERTEX_POINT('',#20714); -#20716=CARTESIAN_POINT('',(3.E0,1.55E0,4.731250143051E0)); -#20717=VERTEX_POINT('',#20716); -#20718=CARTESIAN_POINT('',(4.E0,1.55E0,4.581249856949E0)); -#20719=VERTEX_POINT('',#20718); -#20720=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,3.099999713898E0)); -#20721=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,3.062500286102E0)); -#20722=VERTEX_POINT('',#20720); -#20723=VERTEX_POINT('',#20721); -#20724=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,3.006250286102E0)); -#20725=VERTEX_POINT('',#20724); -#20726=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,2.987499713898E0)); -#20727=VERTEX_POINT('',#20726); -#20728=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.987499713898E0)); -#20729=VERTEX_POINT('',#20728); -#20730=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,3.006250286102E0)); -#20731=VERTEX_POINT('',#20730); -#20732=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,3.062500286102E0)); -#20733=VERTEX_POINT('',#20732); -#20734=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,3.1375E0)); -#20735=VERTEX_POINT('',#20734); -#20736=CARTESIAN_POINT('',(3.E0,1.55E0,3.231250286102E0)); -#20737=VERTEX_POINT('',#20736); -#20738=CARTESIAN_POINT('',(3.E0,1.55E0,3.681249856949E0)); -#20739=VERTEX_POINT('',#20738); -#20740=CARTESIAN_POINT('',(4.E0,1.55E0,3.681249856949E0)); -#20741=VERTEX_POINT('',#20740); -#20742=CARTESIAN_POINT('',(4.E0,1.55E0,3.231250286102E0)); -#20743=VERTEX_POINT('',#20742); -#20744=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,3.1375E0)); -#20745=VERTEX_POINT('',#20744); -#20746=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,3.062500286102E0)); -#20747=VERTEX_POINT('',#20746); -#20748=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,3.006250286102E0)); -#20749=VERTEX_POINT('',#20748); -#20750=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,2.987499713898E0)); -#20751=VERTEX_POINT('',#20750); -#20752=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,2.987499713898E0)); -#20753=VERTEX_POINT('',#20752); -#20754=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,3.006250286102E0)); -#20755=VERTEX_POINT('',#20754); -#20756=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,3.062500286102E0)); -#20757=VERTEX_POINT('',#20756); -#20758=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.568749856949E0)); -#20759=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.212499713898E0)); -#20760=VERTEX_POINT('',#20758); -#20761=VERTEX_POINT('',#20759); -#20762=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,3.156249713898E0)); -#20763=VERTEX_POINT('',#20762); -#20764=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,3.118750286102E0)); -#20765=VERTEX_POINT('',#20764); -#20766=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,3.099999713898E0)); -#20767=VERTEX_POINT('',#20766); -#20768=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,3.099999713898E0)); -#20769=VERTEX_POINT('',#20768); -#20770=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,3.118750286102E0)); -#20771=VERTEX_POINT('',#20770); -#20772=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,3.156249713898E0)); -#20773=VERTEX_POINT('',#20772); -#20774=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.212499713898E0)); -#20775=VERTEX_POINT('',#20774); -#20776=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.568749856949E0)); -#20777=VERTEX_POINT('',#20776); -#20778=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,3.099999713898E0)); -#20779=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,3.099999713898E0)); -#20780=VERTEX_POINT('',#20778); -#20781=VERTEX_POINT('',#20779); -#20782=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,3.118750286102E0)); -#20783=VERTEX_POINT('',#20782); -#20784=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,3.156249713898E0)); -#20785=VERTEX_POINT('',#20784); -#20786=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.212499713898E0)); -#20787=VERTEX_POINT('',#20786); -#20788=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.568749856949E0)); -#20789=VERTEX_POINT('',#20788); -#20790=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.568749856949E0)); -#20791=VERTEX_POINT('',#20790); -#20792=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.212499713898E0)); -#20793=VERTEX_POINT('',#20792); -#20794=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,3.156249713898E0)); -#20795=VERTEX_POINT('',#20794); -#20796=CARTESIAN_POINT('',(3.617021262646E0,1.55E0,3.118750286102E0)); -#20797=VERTEX_POINT('',#20796); -#20798=CARTESIAN_POINT('',(3.E0,1.55E0,2.125E0)); -#20799=CARTESIAN_POINT('',(3.E0,1.55E0,2.837500286102E0)); -#20800=VERTEX_POINT('',#20798); -#20801=VERTEX_POINT('',#20799); -#20802=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.837500286102E0)); -#20803=VERTEX_POINT('',#20802); -#20804=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.537499713898E0)); -#20805=VERTEX_POINT('',#20804); -#20806=CARTESIAN_POINT('',(4.E0,1.55E0,2.537499713898E0)); -#20807=VERTEX_POINT('',#20806); -#20808=CARTESIAN_POINT('',(4.E0,1.55E0,2.424999713898E0)); -#20809=VERTEX_POINT('',#20808); -#20810=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.424999713898E0)); -#20811=VERTEX_POINT('',#20810); -#20812=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.125E0)); -#20813=VERTEX_POINT('',#20812); -#20814=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.825000286102E0)); -#20815=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.862499713898E0)); -#20816=VERTEX_POINT('',#20814); -#20817=VERTEX_POINT('',#20815); -#20818=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.937500286102E0)); -#20819=VERTEX_POINT('',#20818); -#20820=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.974999713898E0)); -#20821=VERTEX_POINT('',#20820); -#20822=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.974999713898E0)); -#20823=VERTEX_POINT('',#20822); -#20824=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.937500286102E0)); -#20825=VERTEX_POINT('',#20824); -#20826=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.881250286102E0)); -#20827=VERTEX_POINT('',#20826); -#20828=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.7875E0)); -#20829=VERTEX_POINT('',#20828); -#20830=CARTESIAN_POINT('',(4.E0,1.55E0,1.693749713898E0)); -#20831=VERTEX_POINT('',#20830); -#20832=CARTESIAN_POINT('',(4.E0,1.55E0,1.581249713898E0)); -#20833=VERTEX_POINT('',#20832); -#20834=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.487500286102E0)); -#20835=VERTEX_POINT('',#20834); -#20836=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.39375E0)); -#20837=VERTEX_POINT('',#20836); -#20838=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.3375E0)); -#20839=VERTEX_POINT('',#20838); -#20840=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.299999713898E0)); -#20841=VERTEX_POINT('',#20840); -#20842=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.299999713898E0)); -#20843=VERTEX_POINT('',#20842); -#20844=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.3375E0)); -#20845=VERTEX_POINT('',#20844); -#20846=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.412499713898E0)); -#20847=VERTEX_POINT('',#20846); -#20848=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.45E0)); -#20849=VERTEX_POINT('',#20848); -#20850=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.412499713898E0)); -#20851=VERTEX_POINT('',#20850); -#20852=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.356249713898E0)); -#20853=VERTEX_POINT('',#20852); -#20854=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.318750286102E0)); -#20855=VERTEX_POINT('',#20854); -#20856=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.318750286102E0)); -#20857=VERTEX_POINT('',#20856); -#20858=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.356249713898E0)); -#20859=VERTEX_POINT('',#20858); -#20860=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.412499713898E0)); -#20861=VERTEX_POINT('',#20860); -#20862=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.50625E0)); -#20863=VERTEX_POINT('',#20862); -#20864=CARTESIAN_POINT('',(3.E0,1.55E0,1.600000286102E0)); -#20865=VERTEX_POINT('',#20864); -#20866=CARTESIAN_POINT('',(3.E0,1.55E0,1.675E0)); -#20867=VERTEX_POINT('',#20866); -#20868=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.768750286102E0)); -#20869=VERTEX_POINT('',#20868); -#20870=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.862499713898E0)); -#20871=VERTEX_POINT('',#20870); -#20872=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.918749713898E0)); -#20873=VERTEX_POINT('',#20872); -#20874=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.95625E0)); -#20875=VERTEX_POINT('',#20874); -#20876=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.95625E0)); -#20877=VERTEX_POINT('',#20876); -#20878=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.918749713898E0)); -#20879=VERTEX_POINT('',#20878); -#20880=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.862499713898E0)); -#20881=VERTEX_POINT('',#20880); -#20882=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.675E0)); -#20883=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.749999713898E0)); -#20884=VERTEX_POINT('',#20882); -#20885=VERTEX_POINT('',#20883); -#20886=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.825000286102E0)); -#20887=VERTEX_POINT('',#20886); -#20888=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.881250286102E0)); -#20889=VERTEX_POINT('',#20888); -#20890=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.881250286102E0)); -#20891=VERTEX_POINT('',#20890); -#20892=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.825000286102E0)); -#20893=VERTEX_POINT('',#20892); -#20894=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.749999713898E0)); -#20895=VERTEX_POINT('',#20894); -#20896=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.675E0)); -#20897=VERTEX_POINT('',#20896); -#20898=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.600000286102E0)); -#20899=VERTEX_POINT('',#20898); -#20900=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.524999713898E0)); -#20901=VERTEX_POINT('',#20900); -#20902=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.45E0)); -#20903=VERTEX_POINT('',#20902); -#20904=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.39375E0)); -#20905=VERTEX_POINT('',#20904); -#20906=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.39375E0)); -#20907=VERTEX_POINT('',#20906); -#20908=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.45E0)); -#20909=VERTEX_POINT('',#20908); -#20910=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.524999713898E0)); -#20911=VERTEX_POINT('',#20910); -#20912=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.600000286102E0)); -#20913=VERTEX_POINT('',#20912); -#20914=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.600000286102E0)); -#20915=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.524999713898E0)); -#20916=VERTEX_POINT('',#20914); -#20917=VERTEX_POINT('',#20915); -#20918=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.45E0)); -#20919=VERTEX_POINT('',#20918); -#20920=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.412499713898E0)); -#20921=VERTEX_POINT('',#20920); -#20922=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.412499713898E0)); -#20923=VERTEX_POINT('',#20922); -#20924=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.45E0)); -#20925=VERTEX_POINT('',#20924); -#20926=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.524999713898E0)); -#20927=VERTEX_POINT('',#20926); -#20928=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.600000286102E0)); -#20929=VERTEX_POINT('',#20928); -#20930=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.675E0)); -#20931=VERTEX_POINT('',#20930); -#20932=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.749999713898E0)); -#20933=VERTEX_POINT('',#20932); -#20934=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.825000286102E0)); -#20935=VERTEX_POINT('',#20934); -#20936=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.862499713898E0)); -#20937=VERTEX_POINT('',#20936); -#20938=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.862499713898E0)); -#20939=VERTEX_POINT('',#20938); -#20940=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.825000286102E0)); -#20941=VERTEX_POINT('',#20940); -#20942=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.749999713898E0)); -#20943=VERTEX_POINT('',#20942); -#20944=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.675E0)); -#20945=VERTEX_POINT('',#20944); -#20946=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.312502861023E-1)); -#20947=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,4.9375E-1)); -#20948=VERTEX_POINT('',#20946); -#20949=VERTEX_POINT('',#20947); -#20950=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.750002861023E-1)); -#20951=VERTEX_POINT('',#20950); -#20952=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.750002861023E-1)); -#20953=VERTEX_POINT('',#20952); -#20954=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,4.9375E-1)); -#20955=VERTEX_POINT('',#20954); -#20956=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.312502861023E-1)); -#20957=VERTEX_POINT('',#20956); -#20958=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.249997138977E-1)); -#20959=VERTEX_POINT('',#20958); -#20960=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.5E-1)); -#20961=VERTEX_POINT('',#20960); -#20962=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.124997138977E-1)); -#20963=VERTEX_POINT('',#20962); -#20964=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,4.9375E-1)); -#20965=VERTEX_POINT('',#20964); -#20966=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,4.9375E-1)); -#20967=VERTEX_POINT('',#20966); -#20968=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.124997138977E-1)); -#20969=VERTEX_POINT('',#20968); -#20970=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,5.875002861023E-1)); -#20971=VERTEX_POINT('',#20970); -#20972=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,6.625E-1)); -#20973=VERTEX_POINT('',#20972); -#20974=CARTESIAN_POINT('',(3.E0,1.55E0,7.937497138977E-1)); -#20975=VERTEX_POINT('',#20974); -#20976=CARTESIAN_POINT('',(3.E0,1.55E0,8.3125E-1)); -#20977=VERTEX_POINT('',#20976); -#20978=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.624997138977E-1)); -#20979=VERTEX_POINT('',#20978); -#20980=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,1.037500286102E0)); -#20981=VERTEX_POINT('',#20980); -#20982=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.1125E0)); -#20983=VERTEX_POINT('',#20982); -#20984=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.131249713898E0)); -#20985=VERTEX_POINT('',#20984); -#20986=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.037500286102E0)); -#20987=VERTEX_POINT('',#20986); -#20988=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.E0)); -#20989=VERTEX_POINT('',#20988); -#20990=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.4375E-1)); -#20991=VERTEX_POINT('',#20990); -#20992=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,8.499997138977E-1)); -#20993=VERTEX_POINT('',#20992); -#20994=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,7.75E-1)); -#20995=VERTEX_POINT('',#20994); -#20996=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,6.812497138977E-1)); -#20997=VERTEX_POINT('',#20996); -#20998=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,6.249997138977E-1)); -#20999=VERTEX_POINT('',#20998); -#21000=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,5.875002861023E-1)); -#21001=VERTEX_POINT('',#21000); -#21002=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,5.875002861023E-1)); -#21003=VERTEX_POINT('',#21002); -#21004=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,6.249997138977E-1)); -#21005=VERTEX_POINT('',#21004); -#21006=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.625E-1)); -#21007=VERTEX_POINT('',#21006); -#21008=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,7.75E-1)); -#21009=VERTEX_POINT('',#21008); -#21010=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,8.499997138977E-1)); -#21011=VERTEX_POINT('',#21010); -#21012=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,8.499997138977E-1)); -#21013=VERTEX_POINT('',#21012); -#21014=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,7.75E-1)); -#21015=VERTEX_POINT('',#21014); -#21016=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,6.625E-1)); -#21017=VERTEX_POINT('',#21016); -#21018=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.0625E-1)); -#21019=VERTEX_POINT('',#21018); -#21020=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.687497138977E-1)); -#21021=VERTEX_POINT('',#21020); -#21022=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,5.687497138977E-1)); -#21023=VERTEX_POINT('',#21022); -#21024=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,5.875002861023E-1)); -#21025=VERTEX_POINT('',#21024); -#21026=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.249997138977E-1)); -#21027=VERTEX_POINT('',#21026); -#21028=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,6.625E-1)); -#21029=VERTEX_POINT('',#21028); -#21030=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,7.562502861023E-1)); -#21031=VERTEX_POINT('',#21030); -#21032=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,8.687502861023E-1)); -#21033=VERTEX_POINT('',#21032); -#21034=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.624997138977E-1)); -#21035=VERTEX_POINT('',#21034); -#21036=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.E0)); -#21037=VERTEX_POINT('',#21036); -#21038=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,1.037500286102E0)); -#21039=VERTEX_POINT('',#21038); -#21040=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.05625E0)); -#21041=VERTEX_POINT('',#21040); -#21042=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.150000286102E0)); -#21043=VERTEX_POINT('',#21042); -#21044=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.131249713898E0)); -#21045=VERTEX_POINT('',#21044); -#21046=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.093750286102E0)); -#21047=VERTEX_POINT('',#21046); -#21048=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,1.037500286102E0)); -#21049=VERTEX_POINT('',#21048); -#21050=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.624997138977E-1)); -#21051=VERTEX_POINT('',#21050); -#21052=CARTESIAN_POINT('',(4.E0,1.55E0,8.875E-1)); -#21053=VERTEX_POINT('',#21052); -#21054=CARTESIAN_POINT('',(4.E0,1.55E0,7.374997138977E-1)); -#21055=VERTEX_POINT('',#21054); -#21056=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,6.625E-1)); -#21057=VERTEX_POINT('',#21056); -#21058=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,5.875002861023E-1)); -#21059=VERTEX_POINT('',#21058); -#21060=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,3.25E-1)); -#21061=CARTESIAN_POINT('',(4.E0,1.55E0,3.25E-1)); -#21062=VERTEX_POINT('',#21060); -#21063=VERTEX_POINT('',#21061); -#21064=CARTESIAN_POINT('',(4.E0,1.55E0,-3.5E-1)); -#21065=VERTEX_POINT('',#21064); -#21066=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,-3.5E-1)); -#21067=VERTEX_POINT('',#21066); -#21068=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.749997138977E-1)); -#21069=VERTEX_POINT('',#21068); -#21070=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,-2.9375E-1)); -#21071=VERTEX_POINT('',#21070); -#21072=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-3.312502861023E-1)); -#21073=VERTEX_POINT('',#21072); -#21074=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-3.5E-1)); -#21075=VERTEX_POINT('',#21074); -#21076=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-3.5E-1)); -#21077=VERTEX_POINT('',#21076); -#21078=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,-3.312502861023E-1)); -#21079=VERTEX_POINT('',#21078); -#21080=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,-2.562497138977E-1)); -#21081=VERTEX_POINT('',#21080); -#21082=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,-1.8125E-1)); -#21083=VERTEX_POINT('',#21082); -#21084=CARTESIAN_POINT('',(3.E0,1.55E0,-6.875E-2)); -#21085=VERTEX_POINT('',#21084); -#21086=CARTESIAN_POINT('',(3.E0,1.55E0,6.249713897704E-3)); -#21087=VERTEX_POINT('',#21086); -#21088=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.375002861023E-1)); -#21089=VERTEX_POINT('',#21088); -#21090=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,2.125E-1)); -#21091=VERTEX_POINT('',#21090); -#21092=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,2.874997138977E-1)); -#21093=VERTEX_POINT('',#21092); -#21094=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,3.062502861023E-1)); -#21095=VERTEX_POINT('',#21094); -#21096=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.125E-1)); -#21097=VERTEX_POINT('',#21096); -#21098=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.749997138977E-1)); -#21099=VERTEX_POINT('',#21098); -#21100=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.187497138977E-1)); -#21101=VERTEX_POINT('',#21100); -#21102=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.500028610229E-2)); -#21103=VERTEX_POINT('',#21102); -#21104=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,-5.000028610230E-2)); -#21105=VERTEX_POINT('',#21104); -#21106=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,-1.437497138977E-1)); -#21107=VERTEX_POINT('',#21106); -#21108=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,-1.999997138977E-1)); -#21109=VERTEX_POINT('',#21108); -#21110=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-2.375E-1)); -#21111=VERTEX_POINT('',#21110); -#21112=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-2.375E-1)); -#21113=VERTEX_POINT('',#21112); -#21114=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-1.999997138977E-1)); -#21115=VERTEX_POINT('',#21114); -#21116=CARTESIAN_POINT('',(5.75E0,1.55E0,1.03375E1)); -#21117=CARTESIAN_POINT('',(4.75E0,1.55E0,1.03375E1)); -#21118=VERTEX_POINT('',#21116); -#21119=VERTEX_POINT('',#21117); -#21120=CARTESIAN_POINT('',(4.75E0,1.55E0,1.045E1)); -#21121=VERTEX_POINT('',#21120); -#21122=CARTESIAN_POINT('',(5.75E0,1.55E0,1.045E1)); -#21123=VERTEX_POINT('',#21122); -#21124=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.456250035763E0)); -#21125=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.568749982119E0)); -#21126=VERTEX_POINT('',#21124); -#21127=VERTEX_POINT('',#21125); -#21128=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,9.587500017881E0)); -#21129=VERTEX_POINT('',#21128); -#21130=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.643750017881E0)); -#21131=VERTEX_POINT('',#21130); -#21132=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.71875E0)); -#21133=VERTEX_POINT('',#21132); -#21134=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.8875E0)); -#21135=VERTEX_POINT('',#21134); -#21136=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.962499982119E0)); -#21137=VERTEX_POINT('',#21136); -#21138=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.001875000894E1)); -#21139=VERTEX_POINT('',#21138); -#21140=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.005625E1)); -#21141=VERTEX_POINT('',#21140); -#21142=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.007500000894E1)); -#21143=VERTEX_POINT('',#21142); -#21144=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.007500000894E1)); -#21145=VERTEX_POINT('',#21144); -#21146=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.005625E1)); -#21147=VERTEX_POINT('',#21146); -#21148=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.001875000894E1)); -#21149=VERTEX_POINT('',#21148); -#21150=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.962499982119E0)); -#21151=VERTEX_POINT('',#21150); -#21152=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.8875E0)); -#21153=VERTEX_POINT('',#21152); -#21154=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.71875E0)); -#21155=VERTEX_POINT('',#21154); -#21156=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.643750017881E0)); -#21157=VERTEX_POINT('',#21156); -#21158=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,9.587500017881E0)); -#21159=VERTEX_POINT('',#21158); -#21160=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.568749982119E0)); -#21161=VERTEX_POINT('',#21160); -#21162=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.456250035763E0)); -#21163=VERTEX_POINT('',#21162); -#21164=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.474999964237E0)); -#21165=VERTEX_POINT('',#21164); -#21166=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,9.55E0)); -#21167=VERTEX_POINT('',#21166); -#21168=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.624999982119E0)); -#21169=VERTEX_POINT('',#21168); -#21170=CARTESIAN_POINT('',(4.75E0,1.55E0,9.71875E0)); -#21171=VERTEX_POINT('',#21170); -#21172=CARTESIAN_POINT('',(4.75E0,1.55E0,9.8875E0)); -#21173=VERTEX_POINT('',#21172); -#21174=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.981250017881E0)); -#21175=VERTEX_POINT('',#21174); -#21176=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.005625E1)); -#21177=VERTEX_POINT('',#21176); -#21178=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.013125000894E1)); -#21179=VERTEX_POINT('',#21178); -#21180=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.016875E1)); -#21181=VERTEX_POINT('',#21180); -#21182=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.018750000894E1)); -#21183=VERTEX_POINT('',#21182); -#21184=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.018750000894E1)); -#21185=VERTEX_POINT('',#21184); -#21186=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.016875E1)); -#21187=VERTEX_POINT('',#21186); -#21188=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.013125000894E1)); -#21189=VERTEX_POINT('',#21188); -#21190=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.005625E1)); -#21191=VERTEX_POINT('',#21190); -#21192=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.981250017881E0)); -#21193=VERTEX_POINT('',#21192); -#21194=CARTESIAN_POINT('',(5.75E0,1.55E0,9.8875E0)); -#21195=VERTEX_POINT('',#21194); -#21196=CARTESIAN_POINT('',(5.75E0,1.55E0,9.71875E0)); -#21197=VERTEX_POINT('',#21196); -#21198=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.624999982119E0)); -#21199=VERTEX_POINT('',#21198); -#21200=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,9.55E0)); -#21201=VERTEX_POINT('',#21200); -#21202=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.474999964237E0)); -#21203=VERTEX_POINT('',#21202); -#21204=CARTESIAN_POINT('',(5.75E0,1.55E0,9.193749964237E0)); -#21205=CARTESIAN_POINT('',(4.75E0,1.55E0,9.193749964237E0)); -#21206=VERTEX_POINT('',#21204); -#21207=VERTEX_POINT('',#21205); -#21208=CARTESIAN_POINT('',(4.75E0,1.55E0,9.306249964237E0)); -#21209=VERTEX_POINT('',#21208); -#21210=CARTESIAN_POINT('',(5.75E0,1.55E0,9.306249964237E0)); -#21211=VERTEX_POINT('',#21210); -#21212=CARTESIAN_POINT('',(4.75E0,1.55E0,8.59375E0)); -#21213=CARTESIAN_POINT('',(4.75E0,1.55E0,9.04375E0)); -#21214=VERTEX_POINT('',#21212); -#21215=VERTEX_POINT('',#21213); -#21216=CARTESIAN_POINT('',(5.75E0,1.55E0,9.04375E0)); -#21217=VERTEX_POINT('',#21216); -#21218=CARTESIAN_POINT('',(5.75E0,1.55E0,8.59375E0)); -#21219=VERTEX_POINT('',#21218); -#21220=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,8.499999928474E0)); -#21221=VERTEX_POINT('',#21220); -#21222=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,8.425E0)); -#21223=VERTEX_POINT('',#21222); -#21224=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.350000071526E0)); -#21225=VERTEX_POINT('',#21224); -#21226=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,8.3125E0)); -#21227=VERTEX_POINT('',#21226); -#21228=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.293750071526E0)); -#21229=VERTEX_POINT('',#21228); -#21230=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.293750071526E0)); -#21231=VERTEX_POINT('',#21230); -#21232=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,8.3125E0)); -#21233=VERTEX_POINT('',#21232); -#21234=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.350000071526E0)); -#21235=VERTEX_POINT('',#21234); -#21236=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,8.425E0)); -#21237=VERTEX_POINT('',#21236); -#21238=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,8.499999928474E0)); -#21239=VERTEX_POINT('',#21238); -#21240=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.93125E0)); -#21241=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.59375E0)); -#21242=VERTEX_POINT('',#21240); -#21243=VERTEX_POINT('',#21241); -#21244=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.518750071526E0)); -#21245=VERTEX_POINT('',#21244); -#21246=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,8.462500071526E0)); -#21247=VERTEX_POINT('',#21246); -#21248=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,8.425E0)); -#21249=VERTEX_POINT('',#21248); -#21250=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.406250071526E0)); -#21251=VERTEX_POINT('',#21250); -#21252=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.406250071526E0)); -#21253=VERTEX_POINT('',#21252); -#21254=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,8.425E0)); -#21255=VERTEX_POINT('',#21254); -#21256=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,8.462500071526E0)); -#21257=VERTEX_POINT('',#21256); -#21258=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.518750071526E0)); -#21259=VERTEX_POINT('',#21258); -#21260=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.59375E0)); -#21261=VERTEX_POINT('',#21260); -#21262=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.93125E0)); -#21263=VERTEX_POINT('',#21262); -#21264=CARTESIAN_POINT('',(5.75E0,1.55E0,8.049999928474E0)); -#21265=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.049999928474E0)); -#21266=VERTEX_POINT('',#21264); -#21267=VERTEX_POINT('',#21265); -#21268=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.14375E0)); -#21269=VERTEX_POINT('',#21268); -#21270=CARTESIAN_POINT('',(5.75E0,1.55E0,8.14375E0)); -#21271=VERTEX_POINT('',#21270); -#21272=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.049999928474E0)); -#21273=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.049999928474E0)); -#21274=VERTEX_POINT('',#21272); -#21275=VERTEX_POINT('',#21273); -#21276=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.14375E0)); -#21277=VERTEX_POINT('',#21276); -#21278=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.14375E0)); -#21279=VERTEX_POINT('',#21278); -#21280=CARTESIAN_POINT('',(4.75E0,1.55E0,7.450000071526E0)); -#21281=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.900000071526E0)); -#21282=VERTEX_POINT('',#21280); -#21283=VERTEX_POINT('',#21281); -#21284=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.900000071526E0)); -#21285=VERTEX_POINT('',#21284); -#21286=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.450000071526E0)); -#21287=VERTEX_POINT('',#21286); -#21288=CARTESIAN_POINT('',(5.75E0,1.55E0,7.450000071526E0)); -#21289=VERTEX_POINT('',#21288); -#21290=CARTESIAN_POINT('',(5.75E0,1.55E0,7.337500071526E0)); -#21291=VERTEX_POINT('',#21290); -#21292=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.337500071526E0)); -#21293=VERTEX_POINT('',#21292); -#21294=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.149999928474E0)); -#21295=VERTEX_POINT('',#21294); -#21296=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.149999928474E0)); -#21297=VERTEX_POINT('',#21296); -#21298=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.337500071526E0)); -#21299=VERTEX_POINT('',#21298); -#21300=CARTESIAN_POINT('',(4.75E0,1.55E0,7.337500071526E0)); -#21301=VERTEX_POINT('',#21300); -#21302=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.768749928474E0)); -#21303=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,7.450000071526E0)); -#21304=VERTEX_POINT('',#21302); -#21305=VERTEX_POINT('',#21303); -#21306=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.450000071526E0)); -#21307=VERTEX_POINT('',#21306); -#21308=CARTESIAN_POINT('',(5.75E0,1.55E0,6.774999856949E0)); -#21309=CARTESIAN_POINT('',(4.75E0,1.55E0,6.774999856949E0)); -#21310=VERTEX_POINT('',#21308); -#21311=VERTEX_POINT('',#21309); -#21312=CARTESIAN_POINT('',(4.75E0,1.55E0,6.887500071526E0)); -#21313=VERTEX_POINT('',#21312); -#21314=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,7.000000071526E0)); -#21315=VERTEX_POINT('',#21314); -#21316=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,7.000000071526E0)); -#21317=VERTEX_POINT('',#21316); -#21318=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.887500071526E0)); -#21319=VERTEX_POINT('',#21318); -#21320=CARTESIAN_POINT('',(5.75E0,1.55E0,6.887500071526E0)); -#21321=VERTEX_POINT('',#21320); -#21322=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.625E0)); -#21323=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,6.625E0)); -#21324=VERTEX_POINT('',#21322); -#21325=VERTEX_POINT('',#21323); -#21326=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.606249856949E0)); -#21327=VERTEX_POINT('',#21326); -#21328=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,6.587500143051E0)); -#21329=VERTEX_POINT('',#21328); -#21330=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.549999856949E0)); -#21331=VERTEX_POINT('',#21330); -#21332=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.493749856949E0)); -#21333=VERTEX_POINT('',#21332); -#21334=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.4E0)); -#21335=VERTEX_POINT('',#21334); -#21336=CARTESIAN_POINT('',(5.75E0,1.55E0,6.2875E0)); -#21337=VERTEX_POINT('',#21336); -#21338=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.175E0)); -#21339=VERTEX_POINT('',#21338); -#21340=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.081250143051E0)); -#21341=VERTEX_POINT('',#21340); -#21342=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.025000143051E0)); -#21343=VERTEX_POINT('',#21342); -#21344=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.987499856949E0)); -#21345=VERTEX_POINT('',#21344); -#21346=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.968750143051E0)); -#21347=VERTEX_POINT('',#21346); -#21348=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.95E0)); -#21349=VERTEX_POINT('',#21348); -#21350=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.95E0)); -#21351=VERTEX_POINT('',#21350); -#21352=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.968750143051E0)); -#21353=VERTEX_POINT('',#21352); -#21354=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.987499856949E0)); -#21355=VERTEX_POINT('',#21354); -#21356=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.025000143051E0)); -#21357=VERTEX_POINT('',#21356); -#21358=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.081250143051E0)); -#21359=VERTEX_POINT('',#21358); -#21360=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.175E0)); -#21361=VERTEX_POINT('',#21360); -#21362=CARTESIAN_POINT('',(4.75E0,1.55E0,6.2875E0)); -#21363=VERTEX_POINT('',#21362); -#21364=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.4E0)); -#21365=VERTEX_POINT('',#21364); -#21366=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.493749856949E0)); -#21367=VERTEX_POINT('',#21366); -#21368=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.549999856949E0)); -#21369=VERTEX_POINT('',#21368); -#21370=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,6.587500143051E0)); -#21371=VERTEX_POINT('',#21370); -#21372=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.606249856949E0)); -#21373=VERTEX_POINT('',#21372); -#21374=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.531250143051E0)); -#21375=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.5125E0)); -#21376=VERTEX_POINT('',#21374); -#21377=VERTEX_POINT('',#21375); -#21378=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.437499856949E0)); -#21379=VERTEX_POINT('',#21378); -#21380=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.381249856949E0)); -#21381=VERTEX_POINT('',#21380); -#21382=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.2875E0)); -#21383=VERTEX_POINT('',#21382); -#21384=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.193750143051E0)); -#21385=VERTEX_POINT('',#21384); -#21386=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.137500143051E0)); -#21387=VERTEX_POINT('',#21386); -#21388=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.0625E0)); -#21389=VERTEX_POINT('',#21388); -#21390=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.043749856949E0)); -#21391=VERTEX_POINT('',#21390); -#21392=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.043749856949E0)); -#21393=VERTEX_POINT('',#21392); -#21394=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.0625E0)); -#21395=VERTEX_POINT('',#21394); -#21396=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.137500143051E0)); -#21397=VERTEX_POINT('',#21396); -#21398=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.193750143051E0)); -#21399=VERTEX_POINT('',#21398); -#21400=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,6.2875E0)); -#21401=VERTEX_POINT('',#21400); -#21402=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.381249856949E0)); -#21403=VERTEX_POINT('',#21402); -#21404=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.437499856949E0)); -#21405=VERTEX_POINT('',#21404); -#21406=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.5125E0)); -#21407=VERTEX_POINT('',#21406); -#21408=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.531250143051E0)); -#21409=VERTEX_POINT('',#21408); -#21410=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.800000143051E0)); -#21411=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.800000143051E0)); -#21412=VERTEX_POINT('',#21410); -#21413=VERTEX_POINT('',#21411); -#21414=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.78125E0)); -#21415=VERTEX_POINT('',#21414); -#21416=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.762499856949E0)); -#21417=VERTEX_POINT('',#21416); -#21418=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.725E0)); -#21419=VERTEX_POINT('',#21418); -#21420=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.66875E0)); -#21421=VERTEX_POINT('',#21420); -#21422=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.575000143051E0)); -#21423=VERTEX_POINT('',#21422); -#21424=CARTESIAN_POINT('',(5.75E0,1.55E0,5.462500143051E0)); -#21425=VERTEX_POINT('',#21424); -#21426=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.350000143051E0)); -#21427=VERTEX_POINT('',#21426); -#21428=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.256249856949E0)); -#21429=VERTEX_POINT('',#21428); -#21430=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.199999856949E0)); -#21431=VERTEX_POINT('',#21430); -#21432=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.1625E0)); -#21433=VERTEX_POINT('',#21432); -#21434=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.143749856949E0)); -#21435=VERTEX_POINT('',#21434); -#21436=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.125000143051E0)); -#21437=VERTEX_POINT('',#21436); -#21438=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.125000143051E0)); -#21439=VERTEX_POINT('',#21438); -#21440=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.143749856949E0)); -#21441=VERTEX_POINT('',#21440); -#21442=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.1625E0)); -#21443=VERTEX_POINT('',#21442); -#21444=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.199999856949E0)); -#21445=VERTEX_POINT('',#21444); -#21446=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.256249856949E0)); -#21447=VERTEX_POINT('',#21446); -#21448=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.350000143051E0)); -#21449=VERTEX_POINT('',#21448); -#21450=CARTESIAN_POINT('',(4.75E0,1.55E0,5.462500143051E0)); -#21451=VERTEX_POINT('',#21450); -#21452=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.575000143051E0)); -#21453=VERTEX_POINT('',#21452); -#21454=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.66875E0)); -#21455=VERTEX_POINT('',#21454); -#21456=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.725E0)); -#21457=VERTEX_POINT('',#21456); -#21458=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.762499856949E0)); -#21459=VERTEX_POINT('',#21458); -#21460=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.78125E0)); -#21461=VERTEX_POINT('',#21460); -#21462=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.706249856949E0)); -#21463=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.687500143051E0)); -#21464=VERTEX_POINT('',#21462); -#21465=VERTEX_POINT('',#21463); -#21466=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.6125E0)); -#21467=VERTEX_POINT('',#21466); -#21468=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.55625E0)); -#21469=VERTEX_POINT('',#21468); -#21470=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,5.462500143051E0)); -#21471=VERTEX_POINT('',#21470); -#21472=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.368749856949E0)); -#21473=VERTEX_POINT('',#21472); -#21474=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.312499856949E0)); -#21475=VERTEX_POINT('',#21474); -#21476=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.237500143051E0)); -#21477=VERTEX_POINT('',#21476); -#21478=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.21875E0)); -#21479=VERTEX_POINT('',#21478); -#21480=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.21875E0)); -#21481=VERTEX_POINT('',#21480); -#21482=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.237500143051E0)); -#21483=VERTEX_POINT('',#21482); -#21484=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.312499856949E0)); -#21485=VERTEX_POINT('',#21484); -#21486=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.368749856949E0)); -#21487=VERTEX_POINT('',#21486); -#21488=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.462500143051E0)); -#21489=VERTEX_POINT('',#21488); -#21490=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.55625E0)); -#21491=VERTEX_POINT('',#21490); -#21492=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.6125E0)); -#21493=VERTEX_POINT('',#21492); -#21494=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.687500143051E0)); -#21495=VERTEX_POINT('',#21494); -#21496=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.706249856949E0)); -#21497=VERTEX_POINT('',#21496); -#21498=CARTESIAN_POINT('',(4.75E0,1.55E0,4.524999856949E0)); -#21499=CARTESIAN_POINT('',(4.75E0,1.55E0,4.675000143051E0)); -#21500=VERTEX_POINT('',#21498); -#21501=VERTEX_POINT('',#21499); -#21502=CARTESIAN_POINT('',(5.75E0,1.55E0,4.974999856949E0)); -#21503=VERTEX_POINT('',#21502); -#21504=CARTESIAN_POINT('',(5.75E0,1.55E0,4.862499856949E0)); -#21505=VERTEX_POINT('',#21504); -#21506=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.787500143051E0)); -#21507=VERTEX_POINT('',#21506); -#21508=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.412499856949E0)); -#21509=VERTEX_POINT('',#21508); -#21510=CARTESIAN_POINT('',(5.75E0,1.55E0,4.337500143051E0)); -#21511=VERTEX_POINT('',#21510); -#21512=CARTESIAN_POINT('',(5.75E0,1.55E0,4.225000143051E0)); -#21513=VERTEX_POINT('',#21512); -#21514=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,4.6E0)); -#21515=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.43125E0)); -#21516=VERTEX_POINT('',#21514); -#21517=VERTEX_POINT('',#21515); -#21518=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.76875E0)); -#21519=VERTEX_POINT('',#21518); -#21520=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,3.8125E0)); -#21521=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,3.8125E0)); -#21522=VERTEX_POINT('',#21520); -#21523=VERTEX_POINT('',#21521); -#21524=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,4.074999856949E0)); -#21525=VERTEX_POINT('',#21524); -#21526=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,4.074999856949E0)); -#21527=VERTEX_POINT('',#21526); -#21528=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,3.08125E0)); -#21529=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,3.043749713898E0)); -#21530=VERTEX_POINT('',#21528); -#21531=VERTEX_POINT('',#21529); -#21532=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,2.987499713898E0)); -#21533=VERTEX_POINT('',#21532); -#21534=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,2.96875E0)); -#21535=VERTEX_POINT('',#21534); -#21536=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.96875E0)); -#21537=VERTEX_POINT('',#21536); -#21538=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,2.987499713898E0)); -#21539=VERTEX_POINT('',#21538); -#21540=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,3.043749713898E0)); -#21541=VERTEX_POINT('',#21540); -#21542=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,3.118750286102E0)); -#21543=VERTEX_POINT('',#21542); -#21544=CARTESIAN_POINT('',(4.75E0,1.55E0,3.212499713898E0)); -#21545=VERTEX_POINT('',#21544); -#21546=CARTESIAN_POINT('',(4.75E0,1.55E0,3.662500143051E0)); -#21547=VERTEX_POINT('',#21546); -#21548=CARTESIAN_POINT('',(5.75E0,1.55E0,3.662500143051E0)); -#21549=VERTEX_POINT('',#21548); -#21550=CARTESIAN_POINT('',(5.75E0,1.55E0,3.212499713898E0)); -#21551=VERTEX_POINT('',#21550); -#21552=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,3.118750286102E0)); -#21553=VERTEX_POINT('',#21552); -#21554=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,3.043749713898E0)); -#21555=VERTEX_POINT('',#21554); -#21556=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,2.987499713898E0)); -#21557=VERTEX_POINT('',#21556); -#21558=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,2.96875E0)); -#21559=VERTEX_POINT('',#21558); -#21560=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,2.96875E0)); -#21561=VERTEX_POINT('',#21560); -#21562=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,2.987499713898E0)); -#21563=VERTEX_POINT('',#21562); -#21564=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,3.043749713898E0)); -#21565=VERTEX_POINT('',#21564); -#21566=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.550000143051E0)); -#21567=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.19375E0)); -#21568=VERTEX_POINT('',#21566); -#21569=VERTEX_POINT('',#21567); -#21570=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,3.1375E0)); -#21571=VERTEX_POINT('',#21570); -#21572=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,3.099999713898E0)); -#21573=VERTEX_POINT('',#21572); -#21574=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,3.08125E0)); -#21575=VERTEX_POINT('',#21574); -#21576=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,3.08125E0)); -#21577=VERTEX_POINT('',#21576); -#21578=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,3.099999713898E0)); -#21579=VERTEX_POINT('',#21578); -#21580=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,3.1375E0)); -#21581=VERTEX_POINT('',#21580); -#21582=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.19375E0)); -#21583=VERTEX_POINT('',#21582); -#21584=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.550000143051E0)); -#21585=VERTEX_POINT('',#21584); -#21586=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,3.08125E0)); -#21587=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,3.08125E0)); -#21588=VERTEX_POINT('',#21586); -#21589=VERTEX_POINT('',#21587); -#21590=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,3.099999713898E0)); -#21591=VERTEX_POINT('',#21590); -#21592=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,3.1375E0)); -#21593=VERTEX_POINT('',#21592); -#21594=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.19375E0)); -#21595=VERTEX_POINT('',#21594); -#21596=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.550000143051E0)); -#21597=VERTEX_POINT('',#21596); -#21598=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.550000143051E0)); -#21599=VERTEX_POINT('',#21598); -#21600=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.19375E0)); -#21601=VERTEX_POINT('',#21600); -#21602=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,3.1375E0)); -#21603=VERTEX_POINT('',#21602); -#21604=CARTESIAN_POINT('',(5.367021262646E0,1.55E0,3.099999713898E0)); -#21605=VERTEX_POINT('',#21604); -#21606=CARTESIAN_POINT('',(4.75E0,1.55E0,2.106250286102E0)); -#21607=CARTESIAN_POINT('',(4.75E0,1.55E0,2.818749713898E0)); -#21608=VERTEX_POINT('',#21606); -#21609=VERTEX_POINT('',#21607); -#21610=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.818749713898E0)); -#21611=VERTEX_POINT('',#21610); -#21612=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.51875E0)); -#21613=VERTEX_POINT('',#21612); -#21614=CARTESIAN_POINT('',(5.75E0,1.55E0,2.51875E0)); -#21615=VERTEX_POINT('',#21614); -#21616=CARTESIAN_POINT('',(5.75E0,1.55E0,2.40625E0)); -#21617=VERTEX_POINT('',#21616); -#21618=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.40625E0)); -#21619=VERTEX_POINT('',#21618); -#21620=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.106250286102E0)); -#21621=VERTEX_POINT('',#21620); -#21622=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.806249713898E0)); -#21623=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.84375E0)); -#21624=VERTEX_POINT('',#21622); -#21625=VERTEX_POINT('',#21623); -#21626=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.918749713898E0)); -#21627=VERTEX_POINT('',#21626); -#21628=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.95625E0)); -#21629=VERTEX_POINT('',#21628); -#21630=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.95625E0)); -#21631=VERTEX_POINT('',#21630); -#21632=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.918749713898E0)); -#21633=VERTEX_POINT('',#21632); -#21634=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.862499713898E0)); -#21635=VERTEX_POINT('',#21634); -#21636=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.768750286102E0)); -#21637=VERTEX_POINT('',#21636); -#21638=CARTESIAN_POINT('',(5.75E0,1.55E0,1.675E0)); -#21639=VERTEX_POINT('',#21638); -#21640=CARTESIAN_POINT('',(5.75E0,1.55E0,1.5625E0)); -#21641=VERTEX_POINT('',#21640); -#21642=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.468749713898E0)); -#21643=VERTEX_POINT('',#21642); -#21644=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.375000286102E0)); -#21645=VERTEX_POINT('',#21644); -#21646=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.318750286102E0)); -#21647=VERTEX_POINT('',#21646); -#21648=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.28125E0)); -#21649=VERTEX_POINT('',#21648); -#21650=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.28125E0)); -#21651=VERTEX_POINT('',#21650); -#21652=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.318750286102E0)); -#21653=VERTEX_POINT('',#21652); -#21654=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.39375E0)); -#21655=VERTEX_POINT('',#21654); -#21656=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.431250286102E0)); -#21657=VERTEX_POINT('',#21656); -#21658=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.39375E0)); -#21659=VERTEX_POINT('',#21658); -#21660=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.3375E0)); -#21661=VERTEX_POINT('',#21660); -#21662=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.299999713898E0)); -#21663=VERTEX_POINT('',#21662); -#21664=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.299999713898E0)); -#21665=VERTEX_POINT('',#21664); -#21666=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.3375E0)); -#21667=VERTEX_POINT('',#21666); -#21668=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.39375E0)); -#21669=VERTEX_POINT('',#21668); -#21670=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.487500286102E0)); -#21671=VERTEX_POINT('',#21670); -#21672=CARTESIAN_POINT('',(4.75E0,1.55E0,1.581249713898E0)); -#21673=VERTEX_POINT('',#21672); -#21674=CARTESIAN_POINT('',(4.75E0,1.55E0,1.656250286102E0)); -#21675=VERTEX_POINT('',#21674); -#21676=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.749999713898E0)); -#21677=VERTEX_POINT('',#21676); -#21678=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.84375E0)); -#21679=VERTEX_POINT('',#21678); -#21680=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.9E0)); -#21681=VERTEX_POINT('',#21680); -#21682=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.937500286102E0)); -#21683=VERTEX_POINT('',#21682); -#21684=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.937500286102E0)); -#21685=VERTEX_POINT('',#21684); -#21686=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.9E0)); -#21687=VERTEX_POINT('',#21686); -#21688=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.84375E0)); -#21689=VERTEX_POINT('',#21688); -#21690=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.656250286102E0)); -#21691=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.73125E0)); -#21692=VERTEX_POINT('',#21690); -#21693=VERTEX_POINT('',#21691); -#21694=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.806249713898E0)); -#21695=VERTEX_POINT('',#21694); -#21696=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.862499713898E0)); -#21697=VERTEX_POINT('',#21696); -#21698=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.862499713898E0)); -#21699=VERTEX_POINT('',#21698); -#21700=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.806249713898E0)); -#21701=VERTEX_POINT('',#21700); -#21702=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.73125E0)); -#21703=VERTEX_POINT('',#21702); -#21704=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.656250286102E0)); -#21705=VERTEX_POINT('',#21704); -#21706=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.581249713898E0)); -#21707=VERTEX_POINT('',#21706); -#21708=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.50625E0)); -#21709=VERTEX_POINT('',#21708); -#21710=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.431250286102E0)); -#21711=VERTEX_POINT('',#21710); -#21712=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.375000286102E0)); -#21713=VERTEX_POINT('',#21712); -#21714=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.375000286102E0)); -#21715=VERTEX_POINT('',#21714); -#21716=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.431250286102E0)); -#21717=VERTEX_POINT('',#21716); -#21718=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.50625E0)); -#21719=VERTEX_POINT('',#21718); -#21720=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.581249713898E0)); -#21721=VERTEX_POINT('',#21720); -#21722=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.581249713898E0)); -#21723=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.50625E0)); -#21724=VERTEX_POINT('',#21722); -#21725=VERTEX_POINT('',#21723); -#21726=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.431250286102E0)); -#21727=VERTEX_POINT('',#21726); -#21728=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.39375E0)); -#21729=VERTEX_POINT('',#21728); -#21730=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.39375E0)); -#21731=VERTEX_POINT('',#21730); -#21732=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.431250286102E0)); -#21733=VERTEX_POINT('',#21732); -#21734=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.50625E0)); -#21735=VERTEX_POINT('',#21734); -#21736=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.581249713898E0)); -#21737=VERTEX_POINT('',#21736); -#21738=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.656250286102E0)); -#21739=VERTEX_POINT('',#21738); -#21740=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.73125E0)); -#21741=VERTEX_POINT('',#21740); -#21742=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.806249713898E0)); -#21743=VERTEX_POINT('',#21742); -#21744=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.84375E0)); -#21745=VERTEX_POINT('',#21744); -#21746=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.84375E0)); -#21747=VERTEX_POINT('',#21746); -#21748=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.806249713898E0)); -#21749=VERTEX_POINT('',#21748); -#21750=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.73125E0)); -#21751=VERTEX_POINT('',#21750); -#21752=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.656250286102E0)); -#21753=VERTEX_POINT('',#21752); -#21754=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.124997138977E-1)); -#21755=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,4.750002861023E-1)); -#21756=VERTEX_POINT('',#21754); -#21757=VERTEX_POINT('',#21755); -#21758=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,4.562497138977E-1)); -#21759=VERTEX_POINT('',#21758); -#21760=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,4.562497138977E-1)); -#21761=VERTEX_POINT('',#21760); -#21762=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,4.750002861023E-1)); -#21763=VERTEX_POINT('',#21762); -#21764=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,5.124997138977E-1)); -#21765=VERTEX_POINT('',#21764); -#21766=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,6.0625E-1)); -#21767=VERTEX_POINT('',#21766); -#21768=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.312502861023E-1)); -#21769=VERTEX_POINT('',#21768); -#21770=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,4.9375E-1)); -#21771=VERTEX_POINT('',#21770); -#21772=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,4.750002861023E-1)); -#21773=VERTEX_POINT('',#21772); -#21774=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,4.750002861023E-1)); -#21775=VERTEX_POINT('',#21774); -#21776=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,4.9375E-1)); -#21777=VERTEX_POINT('',#21776); -#21778=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,5.687497138977E-1)); -#21779=VERTEX_POINT('',#21778); -#21780=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.437502861023E-1)); -#21781=VERTEX_POINT('',#21780); -#21782=CARTESIAN_POINT('',(4.75E0,1.55E0,7.75E-1)); -#21783=VERTEX_POINT('',#21782); -#21784=CARTESIAN_POINT('',(4.75E0,1.55E0,8.125002861023E-1)); -#21785=VERTEX_POINT('',#21784); -#21786=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.4375E-1)); -#21787=VERTEX_POINT('',#21786); -#21788=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.018749713898E0)); -#21789=VERTEX_POINT('',#21788); -#21790=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.093750286102E0)); -#21791=VERTEX_POINT('',#21790); -#21792=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.1125E0)); -#21793=VERTEX_POINT('',#21792); -#21794=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.018749713898E0)); -#21795=VERTEX_POINT('',#21794); -#21796=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,9.812502861023E-1)); -#21797=VERTEX_POINT('',#21796); -#21798=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.250002861023E-1)); -#21799=VERTEX_POINT('',#21798); -#21800=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,8.3125E-1)); -#21801=VERTEX_POINT('',#21800); -#21802=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,7.562502861023E-1)); -#21803=VERTEX_POINT('',#21802); -#21804=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.625E-1)); -#21805=VERTEX_POINT('',#21804); -#21806=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.0625E-1)); -#21807=VERTEX_POINT('',#21806); -#21808=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.687497138977E-1)); -#21809=VERTEX_POINT('',#21808); -#21810=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,5.687497138977E-1)); -#21811=VERTEX_POINT('',#21810); -#21812=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,6.0625E-1)); -#21813=VERTEX_POINT('',#21812); -#21814=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.437502861023E-1)); -#21815=VERTEX_POINT('',#21814); -#21816=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,7.562502861023E-1)); -#21817=VERTEX_POINT('',#21816); -#21818=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,8.3125E-1)); -#21819=VERTEX_POINT('',#21818); -#21820=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,8.3125E-1)); -#21821=VERTEX_POINT('',#21820); -#21822=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,7.562502861023E-1)); -#21823=VERTEX_POINT('',#21822); -#21824=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,6.437502861023E-1)); -#21825=VERTEX_POINT('',#21824); -#21826=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.875002861023E-1)); -#21827=VERTEX_POINT('',#21826); -#21828=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,5.5E-1)); -#21829=VERTEX_POINT('',#21828); -#21830=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.5E-1)); -#21831=VERTEX_POINT('',#21830); -#21832=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,5.687497138977E-1)); -#21833=VERTEX_POINT('',#21832); -#21834=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.0625E-1)); -#21835=VERTEX_POINT('',#21834); -#21836=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.437502861023E-1)); -#21837=VERTEX_POINT('',#21836); -#21838=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,7.374997138977E-1)); -#21839=VERTEX_POINT('',#21838); -#21840=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.499997138977E-1)); -#21841=VERTEX_POINT('',#21840); -#21842=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.4375E-1)); -#21843=VERTEX_POINT('',#21842); -#21844=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.812502861023E-1)); -#21845=VERTEX_POINT('',#21844); -#21846=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.018749713898E0)); -#21847=VERTEX_POINT('',#21846); -#21848=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.037500286102E0)); -#21849=VERTEX_POINT('',#21848); -#21850=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.131249713898E0)); -#21851=VERTEX_POINT('',#21850); -#21852=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.1125E0)); -#21853=VERTEX_POINT('',#21852); -#21854=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.074999713898E0)); -#21855=VERTEX_POINT('',#21854); -#21856=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.018749713898E0)); -#21857=VERTEX_POINT('',#21856); -#21858=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.4375E-1)); -#21859=VERTEX_POINT('',#21858); -#21860=CARTESIAN_POINT('',(5.75E0,1.55E0,8.687502861023E-1)); -#21861=VERTEX_POINT('',#21860); -#21862=CARTESIAN_POINT('',(5.75E0,1.55E0,7.1875E-1)); -#21863=VERTEX_POINT('',#21862); -#21864=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.437502861023E-1)); -#21865=VERTEX_POINT('',#21864); -#21866=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,5.687497138977E-1)); -#21867=VERTEX_POINT('',#21866); -#21868=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,3.062502861023E-1)); -#21869=CARTESIAN_POINT('',(5.75E0,1.55E0,3.062502861023E-1)); -#21870=VERTEX_POINT('',#21868); -#21871=VERTEX_POINT('',#21869); -#21872=CARTESIAN_POINT('',(5.75E0,1.55E0,-3.687497138977E-1)); -#21873=VERTEX_POINT('',#21872); -#21874=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,-3.687497138977E-1)); -#21875=VERTEX_POINT('',#21874); -#21876=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.5625E-1)); -#21877=VERTEX_POINT('',#21876); -#21878=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,-3.124997138977E-1)); -#21879=VERTEX_POINT('',#21878); -#21880=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-3.5E-1)); -#21881=VERTEX_POINT('',#21880); -#21882=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-3.687497138977E-1)); -#21883=VERTEX_POINT('',#21882); -#21884=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-3.687497138977E-1)); -#21885=VERTEX_POINT('',#21884); -#21886=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,-3.5E-1)); -#21887=VERTEX_POINT('',#21886); -#21888=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,-2.750002861023E-1)); -#21889=VERTEX_POINT('',#21888); -#21890=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,-1.999997138977E-1)); -#21891=VERTEX_POINT('',#21890); -#21892=CARTESIAN_POINT('',(4.75E0,1.55E0,-8.749971389771E-2)); -#21893=VERTEX_POINT('',#21892); -#21894=CARTESIAN_POINT('',(4.75E0,1.55E0,-1.25E-2)); -#21895=VERTEX_POINT('',#21894); -#21896=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.187497138977E-1)); -#21897=VERTEX_POINT('',#21896); -#21898=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.937502861023E-1)); -#21899=VERTEX_POINT('',#21898); -#21900=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,2.6875E-1)); -#21901=VERTEX_POINT('',#21900); -#21902=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.874997138977E-1)); -#21903=VERTEX_POINT('',#21902); -#21904=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.937502861023E-1)); -#21905=VERTEX_POINT('',#21904); -#21906=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,1.5625E-1)); -#21907=VERTEX_POINT('',#21906); -#21908=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.E-1)); -#21909=VERTEX_POINT('',#21908); -#21910=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.249713897704E-3)); -#21911=VERTEX_POINT('',#21910); -#21912=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,-6.875E-2)); -#21913=VERTEX_POINT('',#21912); -#21914=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,-1.625002861023E-1)); -#21915=VERTEX_POINT('',#21914); -#21916=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,-2.187502861023E-1)); -#21917=VERTEX_POINT('',#21916); -#21918=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-2.562497138977E-1)); -#21919=VERTEX_POINT('',#21918); -#21920=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-2.562497138977E-1)); -#21921=VERTEX_POINT('',#21920); -#21922=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-2.187502861023E-1)); -#21923=VERTEX_POINT('',#21922); -#21924=CARTESIAN_POINT('',(-2.309434639741E0,1.54E0,7.509479917553E-1)); -#21925=CARTESIAN_POINT('',(-2.309434639741E0,1.54E0,9.019260237562E-2)); -#21926=VERTEX_POINT('',#21924); -#21927=VERTEX_POINT('',#21925); -#21928=VERTEX_POINT('',#14860); -#21929=VERTEX_POINT('',#14853); -#21930=VERTEX_POINT('',#14862); -#21931=VERTEX_POINT('',#14874); -#21932=VERTEX_POINT('',#14880); -#21933=VERTEX_POINT('',#14901); -#21934=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.941801323147E0)); -#21935=VERTEX_POINT('',#21934); -#21936=VERTEX_POINT('',#14914); -#21937=VERTEX_POINT('',#14917); -#21938=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,6.898362595182E0)); -#21939=VERTEX_POINT('',#21938); -#21940=VERTEX_POINT('',#14953); -#21941=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,6.967587730580E0)); -#21942=VERTEX_POINT('',#21941); -#21943=VERTEX_POINT('',#14944); -#21944=CARTESIAN_POINT('',(-1.923218042121E0,1.54E0,6.615024988339E0)); -#21945=VERTEX_POINT('',#21944); -#21946=CARTESIAN_POINT('',(-1.923218042121E0,1.54E0,5.825383145660E0)); -#21947=VERTEX_POINT('',#21946); -#21948=VERTEX_POINT('',#14931); -#21949=CARTESIAN_POINT('',(-3.544453866691E0,1.54E0,5.756586997800E0)); -#21950=VERTEX_POINT('',#21949); -#21951=VERTEX_POINT('',#14959); -#21952=VERTEX_POINT('',#14962); -#21953=CARTESIAN_POINT('',(-2.491243574408E0,1.54E0,8.312648204863E0)); -#21954=VERTEX_POINT('',#21953); -#21955=CARTESIAN_POINT('',(-1.923243519831E0,1.54E0,9.242286387282E0)); -#21956=CARTESIAN_POINT('',(-1.924237150499E0,1.54E0,8.612299065602E0)); -#21957=VERTEX_POINT('',#21955); -#21958=VERTEX_POINT('',#21956); -#21959=VERTEX_POINT('',#15007); -#21960=CARTESIAN_POINT('',(-2.175065200079E0,1.54E0,8.141267173208E0)); -#21961=VERTEX_POINT('',#21960); -#21962=VERTEX_POINT('',#14998); -#21963=CARTESIAN_POINT('',(-1.923307214104E0,1.54E0,7.560244033212E0)); -#21964=VERTEX_POINT('',#21963); -#21965=VERTEX_POINT('',#14989); -#21966=CARTESIAN_POINT('',(-3.544428388982E0,1.54E0,8.226771904890E0)); -#21967=VERTEX_POINT('',#21966); -#21968=CARTESIAN_POINT('',(-1.923192564412E0,1.54E0,1.037838840728E1)); -#21969=CARTESIAN_POINT('',(-1.923192564412E0,1.54E0,9.766460095156E0)); -#21970=VERTEX_POINT('',#21968); -#21971=VERTEX_POINT('',#21969); -#21972=VERTEX_POINT('',#15052); -#21973=CARTESIAN_POINT('',(-2.571600270028E0,1.54E0,8.940553874213E0)); -#21974=VERTEX_POINT('',#21973); -#21975=VERTEX_POINT('',#15043); -#21976=CARTESIAN_POINT('',(-2.917523870145E0,1.54E0,9.402006225147E0)); -#21977=VERTEX_POINT('',#21976); -#21978=VERTEX_POINT('',#15034); -#21979=CARTESIAN_POINT('',(-3.156950644744E0,1.54E0,8.677888105413E0)); -#21980=VERTEX_POINT('',#21979); -#21981=VERTEX_POINT('',#15025); -#21982=CARTESIAN_POINT('',(-3.544441127836E0,1.54E0,9.792991750417E0)); -#21983=VERTEX_POINT('',#21982); -#21984=VERTEX_POINT('',#15054); -#21985=VERTEX_POINT('',#15059); -#21986=CARTESIAN_POINT('',(-1.923574730054E0,1.54E0,1.507661440262E0)); -#21987=VERTEX_POINT('',#21986); -#21988=VERTEX_POINT('',#15200); -#21989=CARTESIAN_POINT('',(-3.544593994093E0,1.54E0,4.269990030724E-1)); -#21990=VERTEX_POINT('',#21989); -#21991=VERTEX_POINT('',#15191); -#21992=CARTESIAN_POINT('',(-3.544415650127E0,1.54E0,2.409368533274E0)); -#21993=VERTEX_POINT('',#21992); -#21994=VERTEX_POINT('',#15174); -#21995=CARTESIAN_POINT('',(-3.156772300777E0,1.54E0,2.906413167021E0)); -#21996=VERTEX_POINT('',#21995); -#21997=VERTEX_POINT('',#15165); -#21998=CARTESIAN_POINT('',(-1.923523774635E0,1.54E0,3.965343205076E0)); -#21999=VERTEX_POINT('',#21998); -#22000=VERTEX_POINT('',#15156); -#22001=CARTESIAN_POINT('',(-3.157179944129E0,1.54E0,3.846769945275E0)); -#22002=VERTEX_POINT('',#22001); -#22003=VERTEX_POINT('',#15147); -#22004=CARTESIAN_POINT('',(-2.391205348235E0,1.54E0,5.564484187773E0)); -#22005=VERTEX_POINT('',#22004); -#22006=VERTEX_POINT('',#15099); -#22007=VERTEX_POINT('',#15079); -#22008=CARTESIAN_POINT('',(-1.795294462950E0,1.54E0,1.040130165008E1)); -#22009=VERTEX_POINT('',#22008); -#22010=VERTEX_POINT('',#15068); -#22011=CARTESIAN_POINT('',(-2.571396448352E0,1.54E0,1.452272899908E0)); -#22012=CARTESIAN_POINT('',(-2.571396448352E0,1.54E0,2.047131002383E0)); -#22013=VERTEX_POINT('',#22011); -#22014=VERTEX_POINT('',#22012); -#22015=VERTEX_POINT('',#15258); -#22016=CARTESIAN_POINT('',(-2.310530181248E0,1.54E0,1.497800082950E0)); -#22017=VERTEX_POINT('',#22016); -#22018=VERTEX_POINT('',#15249); -#22019=CARTESIAN_POINT('',(-1.923625685473E0,1.54E0,2.892655203915E0)); -#22020=VERTEX_POINT('',#22019); -#22021=VERTEX_POINT('',#15240); -#22022=CARTESIAN_POINT('',(-3.543880618228E0,1.54E0,1.048658884147E0)); -#22023=VERTEX_POINT('',#22022); -#22024=VERTEX_POINT('',#15231); -#22025=CARTESIAN_POINT('',(-3.156810517342E0,1.54E0,1.833558752992E0)); -#22026=VERTEX_POINT('',#22025); -#22027=VERTEX_POINT('',#15222); -#22028=CARTESIAN_POINT('',(-2.917332787324E0,1.54E0,1.330285627040E0)); -#22029=VERTEX_POINT('',#22028); -#22030=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,7.509479917553E-1)); -#22031=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,9.019260237562E-2)); -#22032=VERTEX_POINT('',#22030); -#22033=VERTEX_POINT('',#22031); -#22034=VERTEX_POINT('',#6123); -#22035=VERTEX_POINT('',#6130); -#22036=VERTEX_POINT('',#6137); -#22037=VERTEX_POINT('',#6149); -#22038=VERTEX_POINT('',#6155); -#22039=VERTEX_POINT('',#6176); -#22040=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.941801323147E0)); -#22041=VERTEX_POINT('',#22040); -#22042=VERTEX_POINT('',#6189); -#22043=VERTEX_POINT('',#6192); -#22044=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.898362595182E0)); -#22045=VERTEX_POINT('',#22044); -#22046=VERTEX_POINT('',#6198); -#22047=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,6.967587730580E0)); -#22048=VERTEX_POINT('',#22047); -#22049=VERTEX_POINT('',#6207); -#22050=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,6.615024988339E0)); -#22051=VERTEX_POINT('',#22050); -#22052=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,5.825383145660E0)); -#22053=VERTEX_POINT('',#22052); -#22054=VERTEX_POINT('',#6220); -#22055=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.756586997800E0)); -#22056=VERTEX_POINT('',#22055); -#22057=VERTEX_POINT('',#6234); -#22058=VERTEX_POINT('',#6237); -#22059=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.312648204863E0)); -#22060=VERTEX_POINT('',#22059); -#22061=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,9.242286387282E0)); -#22062=CARTESIAN_POINT('',(-1.924237150499E0,1.55E0,8.612299065602E0)); -#22063=VERTEX_POINT('',#22061); -#22064=VERTEX_POINT('',#22062); -#22065=VERTEX_POINT('',#6252); -#22066=CARTESIAN_POINT('',(-2.175065200079E0,1.55E0,8.141267173208E0)); -#22067=VERTEX_POINT('',#22066); -#22068=VERTEX_POINT('',#6261); -#22069=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,7.560244033212E0)); -#22070=VERTEX_POINT('',#22069); -#22071=VERTEX_POINT('',#6270); -#22072=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,8.226771904890E0)); -#22073=VERTEX_POINT('',#22072); -#22074=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,1.037838840728E1)); -#22075=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,9.766460095156E0)); -#22076=VERTEX_POINT('',#22074); -#22077=VERTEX_POINT('',#22075); -#22078=VERTEX_POINT('',#6288); -#22079=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,8.940553874213E0)); -#22080=VERTEX_POINT('',#22079); -#22081=VERTEX_POINT('',#6297); -#22082=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,9.402006225147E0)); -#22083=VERTEX_POINT('',#22082); -#22084=VERTEX_POINT('',#6306); -#22085=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,8.677888105413E0)); -#22086=VERTEX_POINT('',#22085); -#22087=VERTEX_POINT('',#6315); -#22088=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,9.792991750417E0)); -#22089=VERTEX_POINT('',#22088); -#22090=VERTEX_POINT('',#6329); -#22091=VERTEX_POINT('',#6334); -#22092=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.507661440262E0)); -#22093=VERTEX_POINT('',#22092); -#22094=VERTEX_POINT('',#6340); -#22095=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,4.269990030724E-1)); -#22096=VERTEX_POINT('',#22095); -#22097=VERTEX_POINT('',#6360); -#22098=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,2.409368533274E0)); -#22099=VERTEX_POINT('',#22098); -#22100=VERTEX_POINT('',#6366); -#22101=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.906413167021E0)); -#22102=VERTEX_POINT('',#22101); -#22103=VERTEX_POINT('',#6375); -#22104=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.965343205076E0)); -#22105=VERTEX_POINT('',#22104); -#22106=VERTEX_POINT('',#6384); -#22107=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.846769945275E0)); -#22108=VERTEX_POINT('',#22107); -#22109=VERTEX_POINT('',#6435); -#22110=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,5.564484187773E0)); -#22111=VERTEX_POINT('',#22110); -#22112=VERTEX_POINT('',#6459); -#22113=VERTEX_POINT('',#6466); -#22114=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,1.040130165008E1)); -#22115=VERTEX_POINT('',#22114); -#22116=VERTEX_POINT('',#6472); -#22117=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,1.452272899908E0)); -#22118=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,2.047131002383E0)); -#22119=VERTEX_POINT('',#22117); -#22120=VERTEX_POINT('',#22118); -#22121=VERTEX_POINT('',#6485); -#22122=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,1.497800082950E0)); -#22123=VERTEX_POINT('',#22122); -#22124=VERTEX_POINT('',#6494); -#22125=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,2.892655203915E0)); -#22126=VERTEX_POINT('',#22125); -#22127=VERTEX_POINT('',#6503); -#22128=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,1.048658884147E0)); -#22129=VERTEX_POINT('',#22128); -#22130=VERTEX_POINT('',#6512); -#22131=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.833558752992E0)); -#22132=VERTEX_POINT('',#22131); -#22133=VERTEX_POINT('',#6521); -#22134=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.330285627040E0)); -#22135=VERTEX_POINT('',#22134); -#22136=CARTESIAN_POINT('',(0.E0,-3.E-1,0.E0)); -#22137=DIRECTION('',(0.E0,1.E0,0.E0)); -#22138=DIRECTION('',(1.E0,0.E0,0.E0)); -#22139=AXIS2_PLACEMENT_3D('',#22136,#22137,#22138); -#22140=PLANE('',#22139); -#22142=ORIENTED_EDGE('',*,*,#22141,.T.); -#22144=ORIENTED_EDGE('',*,*,#22143,.F.); -#22146=ORIENTED_EDGE('',*,*,#22145,.T.); -#22148=ORIENTED_EDGE('',*,*,#22147,.T.); -#22150=ORIENTED_EDGE('',*,*,#22149,.T.); -#22152=ORIENTED_EDGE('',*,*,#22151,.F.); -#22154=ORIENTED_EDGE('',*,*,#22153,.T.); -#22156=ORIENTED_EDGE('',*,*,#22155,.T.); -#22158=ORIENTED_EDGE('',*,*,#22157,.T.); -#22160=ORIENTED_EDGE('',*,*,#22159,.F.); -#22162=ORIENTED_EDGE('',*,*,#22161,.T.); -#22164=ORIENTED_EDGE('',*,*,#22163,.T.); -#22166=ORIENTED_EDGE('',*,*,#22165,.T.); -#22168=ORIENTED_EDGE('',*,*,#22167,.F.); -#22170=ORIENTED_EDGE('',*,*,#22169,.F.); -#22172=ORIENTED_EDGE('',*,*,#22171,.F.); -#22174=ORIENTED_EDGE('',*,*,#22173,.T.); -#22176=ORIENTED_EDGE('',*,*,#22175,.F.); -#22178=ORIENTED_EDGE('',*,*,#22177,.F.); -#22180=ORIENTED_EDGE('',*,*,#22179,.F.); -#22182=ORIENTED_EDGE('',*,*,#22181,.T.); -#22184=ORIENTED_EDGE('',*,*,#22183,.F.); -#22186=ORIENTED_EDGE('',*,*,#22185,.F.); -#22188=ORIENTED_EDGE('',*,*,#22187,.F.); -#22190=ORIENTED_EDGE('',*,*,#22189,.T.); -#22192=ORIENTED_EDGE('',*,*,#22191,.F.); -#22194=ORIENTED_EDGE('',*,*,#22193,.F.); -#22196=ORIENTED_EDGE('',*,*,#22195,.F.); -#22198=ORIENTED_EDGE('',*,*,#22197,.T.); -#22200=ORIENTED_EDGE('',*,*,#22199,.F.); -#22202=ORIENTED_EDGE('',*,*,#22201,.F.); -#22204=ORIENTED_EDGE('',*,*,#22203,.F.); -#22206=ORIENTED_EDGE('',*,*,#22205,.T.); -#22208=ORIENTED_EDGE('',*,*,#22207,.F.); -#22210=ORIENTED_EDGE('',*,*,#22209,.F.); -#22212=ORIENTED_EDGE('',*,*,#22211,.F.); -#22214=ORIENTED_EDGE('',*,*,#22213,.T.); -#22216=ORIENTED_EDGE('',*,*,#22215,.F.); -#22218=ORIENTED_EDGE('',*,*,#22217,.F.); -#22220=ORIENTED_EDGE('',*,*,#22219,.F.); -#22222=ORIENTED_EDGE('',*,*,#22221,.T.); -#22224=ORIENTED_EDGE('',*,*,#22223,.F.); -#22226=ORIENTED_EDGE('',*,*,#22225,.F.); -#22228=ORIENTED_EDGE('',*,*,#22227,.F.); -#22230=ORIENTED_EDGE('',*,*,#22229,.T.); -#22232=ORIENTED_EDGE('',*,*,#22231,.T.); -#22234=ORIENTED_EDGE('',*,*,#22233,.T.); -#22236=ORIENTED_EDGE('',*,*,#22235,.T.); -#22238=ORIENTED_EDGE('',*,*,#22237,.F.); -#22240=ORIENTED_EDGE('',*,*,#22239,.F.); -#22242=ORIENTED_EDGE('',*,*,#22241,.T.); -#22244=ORIENTED_EDGE('',*,*,#22243,.T.); -#22246=ORIENTED_EDGE('',*,*,#22245,.F.); -#22248=ORIENTED_EDGE('',*,*,#22247,.F.); -#22250=ORIENTED_EDGE('',*,*,#22249,.T.); -#22252=ORIENTED_EDGE('',*,*,#22251,.T.); -#22254=ORIENTED_EDGE('',*,*,#22253,.F.); -#22256=ORIENTED_EDGE('',*,*,#22255,.F.); -#22258=ORIENTED_EDGE('',*,*,#22257,.T.); -#22260=ORIENTED_EDGE('',*,*,#22259,.T.); -#22262=ORIENTED_EDGE('',*,*,#22261,.F.); -#22264=ORIENTED_EDGE('',*,*,#22263,.F.); -#22266=ORIENTED_EDGE('',*,*,#22265,.T.); -#22268=ORIENTED_EDGE('',*,*,#22267,.T.); -#22270=ORIENTED_EDGE('',*,*,#22269,.F.); -#22272=ORIENTED_EDGE('',*,*,#22271,.F.); -#22274=ORIENTED_EDGE('',*,*,#22273,.T.); -#22276=ORIENTED_EDGE('',*,*,#22275,.T.); -#22278=ORIENTED_EDGE('',*,*,#22277,.F.); -#22280=ORIENTED_EDGE('',*,*,#22279,.F.); -#22282=ORIENTED_EDGE('',*,*,#22281,.T.); -#22284=ORIENTED_EDGE('',*,*,#22283,.T.); -#22286=ORIENTED_EDGE('',*,*,#22285,.F.); -#22288=ORIENTED_EDGE('',*,*,#22287,.F.); -#22290=ORIENTED_EDGE('',*,*,#22289,.T.); -#22292=ORIENTED_EDGE('',*,*,#22291,.T.); -#22294=ORIENTED_EDGE('',*,*,#22293,.F.); -#22296=ORIENTED_EDGE('',*,*,#22295,.F.); -#22298=ORIENTED_EDGE('',*,*,#22297,.T.); -#22300=ORIENTED_EDGE('',*,*,#22299,.T.); -#22302=ORIENTED_EDGE('',*,*,#22301,.T.); -#22304=ORIENTED_EDGE('',*,*,#22303,.T.); -#22305=EDGE_LOOP('',(#22142,#22144,#22146,#22148,#22150,#22152,#22154,#22156, -#22158,#22160,#22162,#22164,#22166,#22168,#22170,#22172,#22174,#22176,#22178, -#22180,#22182,#22184,#22186,#22188,#22190,#22192,#22194,#22196,#22198,#22200, -#22202,#22204,#22206,#22208,#22210,#22212,#22214,#22216,#22218,#22220,#22222, -#22224,#22226,#22228,#22230,#22232,#22234,#22236,#22238,#22240,#22242,#22244, -#22246,#22248,#22250,#22252,#22254,#22256,#22258,#22260,#22262,#22264,#22266, -#22268,#22270,#22272,#22274,#22276,#22278,#22280,#22282,#22284,#22286,#22288, -#22290,#22292,#22294,#22296,#22298,#22300,#22302,#22304)); -#22306=FACE_OUTER_BOUND('',#22305,.F.); -#22308=ORIENTED_EDGE('',*,*,#22307,.T.); -#22310=ORIENTED_EDGE('',*,*,#22309,.T.); -#22311=EDGE_LOOP('',(#22308,#22310)); -#22312=FACE_BOUND('',#22311,.F.); -#22314=ORIENTED_EDGE('',*,*,#22313,.T.); -#22316=ORIENTED_EDGE('',*,*,#22315,.T.); -#22317=EDGE_LOOP('',(#22314,#22316)); -#22318=FACE_BOUND('',#22317,.F.); -#22320=ORIENTED_EDGE('',*,*,#22319,.T.); -#22322=ORIENTED_EDGE('',*,*,#22321,.T.); -#22323=EDGE_LOOP('',(#22320,#22322)); -#22324=FACE_BOUND('',#22323,.F.); -#22326=ORIENTED_EDGE('',*,*,#22325,.T.); -#22328=ORIENTED_EDGE('',*,*,#22327,.T.); -#22329=EDGE_LOOP('',(#22326,#22328)); -#22330=FACE_BOUND('',#22329,.F.); -#22332=ORIENTED_EDGE('',*,*,#22331,.T.); -#22334=ORIENTED_EDGE('',*,*,#22333,.T.); -#22335=EDGE_LOOP('',(#22332,#22334)); -#22336=FACE_BOUND('',#22335,.F.); -#22338=ORIENTED_EDGE('',*,*,#22337,.T.); -#22340=ORIENTED_EDGE('',*,*,#22339,.T.); -#22341=EDGE_LOOP('',(#22338,#22340)); -#22342=FACE_BOUND('',#22341,.F.); -#22344=ORIENTED_EDGE('',*,*,#22343,.T.); -#22346=ORIENTED_EDGE('',*,*,#22345,.T.); -#22347=EDGE_LOOP('',(#22344,#22346)); -#22348=FACE_BOUND('',#22347,.F.); -#22350=ORIENTED_EDGE('',*,*,#22349,.T.); -#22352=ORIENTED_EDGE('',*,*,#22351,.T.); -#22353=EDGE_LOOP('',(#22350,#22352)); -#22354=FACE_BOUND('',#22353,.F.); -#22356=ORIENTED_EDGE('',*,*,#22355,.T.); -#22358=ORIENTED_EDGE('',*,*,#22357,.T.); -#22359=EDGE_LOOP('',(#22356,#22358)); -#22360=FACE_BOUND('',#22359,.F.); -#22362=ORIENTED_EDGE('',*,*,#22361,.T.); -#22364=ORIENTED_EDGE('',*,*,#22363,.T.); -#22365=EDGE_LOOP('',(#22362,#22364)); -#22366=FACE_BOUND('',#22365,.F.); -#22368=ORIENTED_EDGE('',*,*,#22367,.T.); -#22370=ORIENTED_EDGE('',*,*,#22369,.T.); -#22371=EDGE_LOOP('',(#22368,#22370)); -#22372=FACE_BOUND('',#22371,.F.); -#22374=ORIENTED_EDGE('',*,*,#22373,.T.); -#22376=ORIENTED_EDGE('',*,*,#22375,.T.); -#22377=EDGE_LOOP('',(#22374,#22376)); -#22378=FACE_BOUND('',#22377,.F.); -#22380=ORIENTED_EDGE('',*,*,#22379,.T.); -#22382=ORIENTED_EDGE('',*,*,#22381,.T.); -#22383=EDGE_LOOP('',(#22380,#22382)); -#22384=FACE_BOUND('',#22383,.F.); -#22386=ORIENTED_EDGE('',*,*,#22385,.T.); -#22388=ORIENTED_EDGE('',*,*,#22387,.T.); -#22389=EDGE_LOOP('',(#22386,#22388)); -#22390=FACE_BOUND('',#22389,.F.); -#22392=ORIENTED_EDGE('',*,*,#22391,.T.); -#22394=ORIENTED_EDGE('',*,*,#22393,.T.); -#22395=EDGE_LOOP('',(#22392,#22394)); -#22396=FACE_BOUND('',#22395,.F.); -#22398=ORIENTED_EDGE('',*,*,#22397,.T.); -#22400=ORIENTED_EDGE('',*,*,#22399,.T.); -#22401=EDGE_LOOP('',(#22398,#22400)); -#22402=FACE_BOUND('',#22401,.F.); -#22404=ORIENTED_EDGE('',*,*,#22403,.T.); -#22406=ORIENTED_EDGE('',*,*,#22405,.T.); -#22407=EDGE_LOOP('',(#22404,#22406)); -#22408=FACE_BOUND('',#22407,.F.); -#22410=ORIENTED_EDGE('',*,*,#22409,.T.); -#22412=ORIENTED_EDGE('',*,*,#22411,.T.); -#22413=EDGE_LOOP('',(#22410,#22412)); -#22414=FACE_BOUND('',#22413,.F.); -#22416=ORIENTED_EDGE('',*,*,#22415,.T.); -#22418=ORIENTED_EDGE('',*,*,#22417,.T.); -#22419=EDGE_LOOP('',(#22416,#22418)); -#22420=FACE_BOUND('',#22419,.F.); -#22422=ORIENTED_EDGE('',*,*,#22421,.T.); -#22424=ORIENTED_EDGE('',*,*,#22423,.T.); -#22425=EDGE_LOOP('',(#22422,#22424)); -#22426=FACE_BOUND('',#22425,.F.); -#22428=ORIENTED_EDGE('',*,*,#22427,.T.); -#22430=ORIENTED_EDGE('',*,*,#22429,.T.); -#22431=EDGE_LOOP('',(#22428,#22430)); -#22432=FACE_BOUND('',#22431,.F.); -#22434=ORIENTED_EDGE('',*,*,#22433,.T.); -#22436=ORIENTED_EDGE('',*,*,#22435,.T.); -#22437=EDGE_LOOP('',(#22434,#22436)); -#22438=FACE_BOUND('',#22437,.F.); -#22440=ORIENTED_EDGE('',*,*,#22439,.T.); -#22442=ORIENTED_EDGE('',*,*,#22441,.T.); -#22443=EDGE_LOOP('',(#22440,#22442)); -#22444=FACE_BOUND('',#22443,.F.); -#22446=ORIENTED_EDGE('',*,*,#22445,.T.); -#22448=ORIENTED_EDGE('',*,*,#22447,.T.); -#22450=ORIENTED_EDGE('',*,*,#22449,.T.); -#22452=ORIENTED_EDGE('',*,*,#22451,.T.); -#22453=EDGE_LOOP('',(#22446,#22448,#22450,#22452)); -#22454=FACE_BOUND('',#22453,.F.); -#22456=ORIENTED_EDGE('',*,*,#22455,.T.); -#22458=ORIENTED_EDGE('',*,*,#22457,.T.); -#22460=ORIENTED_EDGE('',*,*,#22459,.T.); -#22462=ORIENTED_EDGE('',*,*,#22461,.T.); -#22463=EDGE_LOOP('',(#22456,#22458,#22460,#22462)); -#22464=FACE_BOUND('',#22463,.F.); -#22466=ORIENTED_EDGE('',*,*,#22465,.T.); -#22468=ORIENTED_EDGE('',*,*,#22467,.T.); -#22470=ORIENTED_EDGE('',*,*,#22469,.T.); -#22472=ORIENTED_EDGE('',*,*,#22471,.T.); -#22473=EDGE_LOOP('',(#22466,#22468,#22470,#22472)); -#22474=FACE_BOUND('',#22473,.F.); -#22476=ORIENTED_EDGE('',*,*,#22475,.T.); -#22478=ORIENTED_EDGE('',*,*,#22477,.T.); -#22480=ORIENTED_EDGE('',*,*,#22479,.T.); -#22482=ORIENTED_EDGE('',*,*,#22481,.T.); -#22483=EDGE_LOOP('',(#22476,#22478,#22480,#22482)); -#22484=FACE_BOUND('',#22483,.F.); -#22486=ORIENTED_EDGE('',*,*,#22485,.T.); -#22488=ORIENTED_EDGE('',*,*,#22487,.T.); -#22489=EDGE_LOOP('',(#22486,#22488)); -#22490=FACE_BOUND('',#22489,.F.); -#22492=FILL_AREA_STYLE_COLOUR('',#4); -#22493=FILL_AREA_STYLE('',(#22492)); -#22494=SURFACE_STYLE_FILL_AREA(#22493); -#22495=SURFACE_SIDE_STYLE('',(#22494)); -#22496=SURFACE_STYLE_USAGE(.NEGATIVE.,#22495); -#22497=PRESENTATION_STYLE_ASSIGNMENT((#22496)); -#22498=STYLED_ITEM('',(#22497),#22491); -#22499=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.17E1)); -#22500=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22501=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22502=AXIS2_PLACEMENT_3D('',#22499,#22500,#22501); -#22503=CYLINDRICAL_SURFACE('',#22502,3.E-1); -#22504=ORIENTED_EDGE('',*,*,#22485,.F.); -#22506=ORIENTED_EDGE('',*,*,#22505,.T.); -#22508=ORIENTED_EDGE('',*,*,#22507,.F.); -#22510=ORIENTED_EDGE('',*,*,#22509,.F.); -#22511=EDGE_LOOP('',(#22504,#22506,#22508,#22510)); -#22512=FACE_OUTER_BOUND('',#22511,.F.); -#22514=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.17E1)); -#22515=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22516=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22517=AXIS2_PLACEMENT_3D('',#22514,#22515,#22516); -#22518=CYLINDRICAL_SURFACE('',#22517,3.E-1); -#22519=ORIENTED_EDGE('',*,*,#22487,.F.); -#22520=ORIENTED_EDGE('',*,*,#22509,.T.); -#22522=ORIENTED_EDGE('',*,*,#22521,.F.); -#22523=ORIENTED_EDGE('',*,*,#22505,.F.); -#22524=EDGE_LOOP('',(#22519,#22520,#22522,#22523)); -#22525=FACE_OUTER_BOUND('',#22524,.F.); -#22527=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22528=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22529=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22530=AXIS2_PLACEMENT_3D('',#22527,#22528,#22529); -#22531=PLANE('',#22530); -#22532=ORIENTED_EDGE('',*,*,#22507,.T.); -#22533=ORIENTED_EDGE('',*,*,#22521,.T.); -#22534=EDGE_LOOP('',(#22532,#22533)); -#22535=FACE_OUTER_BOUND('',#22534,.F.); -#22537=FILL_AREA_STYLE_COLOUR('',#15); -#22538=FILL_AREA_STYLE('',(#22537)); -#22539=SURFACE_STYLE_FILL_AREA(#22538); -#22540=SURFACE_SIDE_STYLE('',(#22539)); -#22541=SURFACE_STYLE_USAGE(.POSITIVE.,#22540); -#22542=PRESENTATION_STYLE_ASSIGNMENT((#22541)); -#22543=STYLED_ITEM('',(#22542),#22536); -#22544=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22545=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22546=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22547=AXIS2_PLACEMENT_3D('',#22544,#22545,#22546); -#22548=PLANE('',#22547); -#22550=ORIENTED_EDGE('',*,*,#22549,.T.); -#22552=ORIENTED_EDGE('',*,*,#22551,.T.); -#22553=EDGE_LOOP('',(#22550,#22552)); -#22554=FACE_OUTER_BOUND('',#22553,.F.); -#22556=FILL_AREA_STYLE_COLOUR('',#15); -#22557=FILL_AREA_STYLE('',(#22556)); -#22558=SURFACE_STYLE_FILL_AREA(#22557); -#22559=SURFACE_SIDE_STYLE('',(#22558)); -#22560=SURFACE_STYLE_USAGE(.POSITIVE.,#22559); -#22561=PRESENTATION_STYLE_ASSIGNMENT((#22560)); -#22562=STYLED_ITEM('',(#22561),#22555); -#22563=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22564=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22565=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22566=AXIS2_PLACEMENT_3D('',#22563,#22564,#22565); -#22567=PLANE('',#22566); -#22569=ORIENTED_EDGE('',*,*,#22568,.T.); -#22571=ORIENTED_EDGE('',*,*,#22570,.T.); -#22572=EDGE_LOOP('',(#22569,#22571)); -#22573=FACE_OUTER_BOUND('',#22572,.F.); -#22575=FILL_AREA_STYLE_COLOUR('',#15); -#22576=FILL_AREA_STYLE('',(#22575)); -#22577=SURFACE_STYLE_FILL_AREA(#22576); -#22578=SURFACE_SIDE_STYLE('',(#22577)); -#22579=SURFACE_STYLE_USAGE(.POSITIVE.,#22578); -#22580=PRESENTATION_STYLE_ASSIGNMENT((#22579)); -#22581=STYLED_ITEM('',(#22580),#22574); -#22582=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22583=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22584=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22585=AXIS2_PLACEMENT_3D('',#22582,#22583,#22584); -#22586=PLANE('',#22585); -#22588=ORIENTED_EDGE('',*,*,#22587,.T.); -#22590=ORIENTED_EDGE('',*,*,#22589,.T.); -#22591=EDGE_LOOP('',(#22588,#22590)); -#22592=FACE_OUTER_BOUND('',#22591,.F.); -#22594=FILL_AREA_STYLE_COLOUR('',#15); -#22595=FILL_AREA_STYLE('',(#22594)); -#22596=SURFACE_STYLE_FILL_AREA(#22595); -#22597=SURFACE_SIDE_STYLE('',(#22596)); -#22598=SURFACE_STYLE_USAGE(.POSITIVE.,#22597); -#22599=PRESENTATION_STYLE_ASSIGNMENT((#22598)); -#22600=STYLED_ITEM('',(#22599),#22593); -#22601=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.17E1)); -#22602=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22603=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22604=AXIS2_PLACEMENT_3D('',#22601,#22602,#22603); -#22605=CYLINDRICAL_SURFACE('',#22604,3.E-1); -#22606=ORIENTED_EDGE('',*,*,#22307,.F.); -#22608=ORIENTED_EDGE('',*,*,#22607,.T.); -#22609=ORIENTED_EDGE('',*,*,#22549,.F.); -#22611=ORIENTED_EDGE('',*,*,#22610,.F.); -#22612=EDGE_LOOP('',(#22606,#22608,#22609,#22611)); -#22613=FACE_OUTER_BOUND('',#22612,.F.); -#22615=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.17E1)); -#22616=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22617=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22618=AXIS2_PLACEMENT_3D('',#22615,#22616,#22617); -#22619=CYLINDRICAL_SURFACE('',#22618,3.E-1); -#22620=ORIENTED_EDGE('',*,*,#22309,.F.); -#22621=ORIENTED_EDGE('',*,*,#22610,.T.); -#22622=ORIENTED_EDGE('',*,*,#22551,.F.); -#22623=ORIENTED_EDGE('',*,*,#22607,.F.); -#22624=EDGE_LOOP('',(#22620,#22621,#22622,#22623)); -#22625=FACE_OUTER_BOUND('',#22624,.F.); -#22627=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.17E1)); -#22628=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22629=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22630=AXIS2_PLACEMENT_3D('',#22627,#22628,#22629); -#22631=CYLINDRICAL_SURFACE('',#22630,3.E-1); -#22632=ORIENTED_EDGE('',*,*,#22313,.F.); -#22634=ORIENTED_EDGE('',*,*,#22633,.T.); -#22635=ORIENTED_EDGE('',*,*,#22568,.F.); -#22637=ORIENTED_EDGE('',*,*,#22636,.F.); -#22638=EDGE_LOOP('',(#22632,#22634,#22635,#22637)); -#22639=FACE_OUTER_BOUND('',#22638,.F.); -#22641=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.17E1)); -#22642=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22643=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22644=AXIS2_PLACEMENT_3D('',#22641,#22642,#22643); -#22645=CYLINDRICAL_SURFACE('',#22644,3.E-1); -#22646=ORIENTED_EDGE('',*,*,#22315,.F.); -#22647=ORIENTED_EDGE('',*,*,#22636,.T.); -#22648=ORIENTED_EDGE('',*,*,#22570,.F.); -#22649=ORIENTED_EDGE('',*,*,#22633,.F.); -#22650=EDGE_LOOP('',(#22646,#22647,#22648,#22649)); -#22651=FACE_OUTER_BOUND('',#22650,.F.); -#22653=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.17E1)); -#22654=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22655=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22656=AXIS2_PLACEMENT_3D('',#22653,#22654,#22655); -#22657=CYLINDRICAL_SURFACE('',#22656,3.E-1); -#22658=ORIENTED_EDGE('',*,*,#22319,.F.); -#22660=ORIENTED_EDGE('',*,*,#22659,.T.); -#22661=ORIENTED_EDGE('',*,*,#22587,.F.); -#22663=ORIENTED_EDGE('',*,*,#22662,.F.); -#22664=EDGE_LOOP('',(#22658,#22660,#22661,#22663)); -#22665=FACE_OUTER_BOUND('',#22664,.F.); -#22667=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.17E1)); -#22668=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22669=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22670=AXIS2_PLACEMENT_3D('',#22667,#22668,#22669); -#22671=CYLINDRICAL_SURFACE('',#22670,3.E-1); -#22672=ORIENTED_EDGE('',*,*,#22321,.F.); -#22673=ORIENTED_EDGE('',*,*,#22662,.T.); -#22674=ORIENTED_EDGE('',*,*,#22589,.F.); -#22675=ORIENTED_EDGE('',*,*,#22659,.F.); -#22676=EDGE_LOOP('',(#22672,#22673,#22674,#22675)); -#22677=FACE_OUTER_BOUND('',#22676,.F.); -#22679=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.05E1)); -#22680=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22681=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22682=AXIS2_PLACEMENT_3D('',#22679,#22680,#22681); -#22683=CYLINDRICAL_SURFACE('',#22682,3.E-1); -#22684=ORIENTED_EDGE('',*,*,#22325,.F.); -#22686=ORIENTED_EDGE('',*,*,#22685,.T.); -#22688=ORIENTED_EDGE('',*,*,#22687,.T.); -#22690=ORIENTED_EDGE('',*,*,#22689,.F.); -#22691=EDGE_LOOP('',(#22684,#22686,#22688,#22690)); -#22692=FACE_OUTER_BOUND('',#22691,.F.); -#22694=CARTESIAN_POINT('',(2.75E0,-3.E-1,1.05E1)); -#22695=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22696=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22697=AXIS2_PLACEMENT_3D('',#22694,#22695,#22696); -#22698=CYLINDRICAL_SURFACE('',#22697,3.E-1); -#22699=ORIENTED_EDGE('',*,*,#22327,.F.); -#22700=ORIENTED_EDGE('',*,*,#22689,.T.); -#22702=ORIENTED_EDGE('',*,*,#22701,.T.); -#22703=ORIENTED_EDGE('',*,*,#22685,.F.); -#22704=EDGE_LOOP('',(#22699,#22700,#22702,#22703)); -#22705=FACE_OUTER_BOUND('',#22704,.F.); -#22707=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22708=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22709=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22710=AXIS2_PLACEMENT_3D('',#22707,#22708,#22709); -#22711=PLANE('',#22710); -#22712=ORIENTED_EDGE('',*,*,#22687,.F.); -#22713=ORIENTED_EDGE('',*,*,#22701,.F.); -#22714=EDGE_LOOP('',(#22712,#22713)); -#22715=FACE_OUTER_BOUND('',#22714,.F.); -#22717=FILL_AREA_STYLE_COLOUR('',#15); -#22718=FILL_AREA_STYLE('',(#22717)); -#22719=SURFACE_STYLE_FILL_AREA(#22718); -#22720=SURFACE_SIDE_STYLE('',(#22719)); -#22721=SURFACE_STYLE_USAGE(.POSITIVE.,#22720); -#22722=PRESENTATION_STYLE_ASSIGNMENT((#22721)); -#22723=STYLED_ITEM('',(#22722),#22716); -#22724=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22725=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22726=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22727=AXIS2_PLACEMENT_3D('',#22724,#22725,#22726); -#22728=PLANE('',#22727); -#22730=ORIENTED_EDGE('',*,*,#22729,.F.); -#22732=ORIENTED_EDGE('',*,*,#22731,.F.); -#22733=EDGE_LOOP('',(#22730,#22732)); -#22734=FACE_OUTER_BOUND('',#22733,.F.); -#22736=FILL_AREA_STYLE_COLOUR('',#15); -#22737=FILL_AREA_STYLE('',(#22736)); -#22738=SURFACE_STYLE_FILL_AREA(#22737); -#22739=SURFACE_SIDE_STYLE('',(#22738)); -#22740=SURFACE_STYLE_USAGE(.POSITIVE.,#22739); -#22741=PRESENTATION_STYLE_ASSIGNMENT((#22740)); -#22742=STYLED_ITEM('',(#22741),#22735); -#22743=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22744=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22745=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22746=AXIS2_PLACEMENT_3D('',#22743,#22744,#22745); -#22747=PLANE('',#22746); -#22749=ORIENTED_EDGE('',*,*,#22748,.F.); -#22751=ORIENTED_EDGE('',*,*,#22750,.F.); -#22752=EDGE_LOOP('',(#22749,#22751)); -#22753=FACE_OUTER_BOUND('',#22752,.F.); -#22755=FILL_AREA_STYLE_COLOUR('',#15); -#22756=FILL_AREA_STYLE('',(#22755)); -#22757=SURFACE_STYLE_FILL_AREA(#22756); -#22758=SURFACE_SIDE_STYLE('',(#22757)); -#22759=SURFACE_STYLE_USAGE(.POSITIVE.,#22758); -#22760=PRESENTATION_STYLE_ASSIGNMENT((#22759)); -#22761=STYLED_ITEM('',(#22760),#22754); -#22762=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22763=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22764=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22765=AXIS2_PLACEMENT_3D('',#22762,#22763,#22764); -#22766=PLANE('',#22765); -#22768=ORIENTED_EDGE('',*,*,#22767,.F.); -#22770=ORIENTED_EDGE('',*,*,#22769,.F.); -#22771=EDGE_LOOP('',(#22768,#22770)); -#22772=FACE_OUTER_BOUND('',#22771,.F.); -#22774=FILL_AREA_STYLE_COLOUR('',#15); -#22775=FILL_AREA_STYLE('',(#22774)); -#22776=SURFACE_STYLE_FILL_AREA(#22775); -#22777=SURFACE_SIDE_STYLE('',(#22776)); -#22778=SURFACE_STYLE_USAGE(.POSITIVE.,#22777); -#22779=PRESENTATION_STYLE_ASSIGNMENT((#22778)); -#22780=STYLED_ITEM('',(#22779),#22773); -#22781=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.05E1)); -#22782=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22783=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22784=AXIS2_PLACEMENT_3D('',#22781,#22782,#22783); -#22785=CYLINDRICAL_SURFACE('',#22784,3.E-1); -#22786=ORIENTED_EDGE('',*,*,#22331,.F.); -#22788=ORIENTED_EDGE('',*,*,#22787,.T.); -#22789=ORIENTED_EDGE('',*,*,#22729,.T.); -#22791=ORIENTED_EDGE('',*,*,#22790,.F.); -#22792=EDGE_LOOP('',(#22786,#22788,#22789,#22791)); -#22793=FACE_OUTER_BOUND('',#22792,.F.); -#22795=CARTESIAN_POINT('',(1.25E0,-3.E-1,1.05E1)); -#22796=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22797=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22798=AXIS2_PLACEMENT_3D('',#22795,#22796,#22797); -#22799=CYLINDRICAL_SURFACE('',#22798,3.E-1); -#22800=ORIENTED_EDGE('',*,*,#22333,.F.); -#22801=ORIENTED_EDGE('',*,*,#22790,.T.); -#22802=ORIENTED_EDGE('',*,*,#22731,.T.); -#22803=ORIENTED_EDGE('',*,*,#22787,.F.); -#22804=EDGE_LOOP('',(#22800,#22801,#22802,#22803)); -#22805=FACE_OUTER_BOUND('',#22804,.F.); -#22807=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.05E1)); -#22808=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22809=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22810=AXIS2_PLACEMENT_3D('',#22807,#22808,#22809); -#22811=CYLINDRICAL_SURFACE('',#22810,3.E-1); -#22812=ORIENTED_EDGE('',*,*,#22337,.F.); -#22814=ORIENTED_EDGE('',*,*,#22813,.T.); -#22815=ORIENTED_EDGE('',*,*,#22748,.T.); -#22817=ORIENTED_EDGE('',*,*,#22816,.F.); -#22818=EDGE_LOOP('',(#22812,#22814,#22815,#22817)); -#22819=FACE_OUTER_BOUND('',#22818,.F.); -#22821=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,1.05E1)); -#22822=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22823=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22824=AXIS2_PLACEMENT_3D('',#22821,#22822,#22823); -#22825=CYLINDRICAL_SURFACE('',#22824,3.E-1); -#22826=ORIENTED_EDGE('',*,*,#22339,.F.); -#22827=ORIENTED_EDGE('',*,*,#22816,.T.); -#22828=ORIENTED_EDGE('',*,*,#22750,.T.); -#22829=ORIENTED_EDGE('',*,*,#22813,.F.); -#22830=EDGE_LOOP('',(#22826,#22827,#22828,#22829)); -#22831=FACE_OUTER_BOUND('',#22830,.F.); -#22833=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.05E1)); -#22834=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22835=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22836=AXIS2_PLACEMENT_3D('',#22833,#22834,#22835); -#22837=CYLINDRICAL_SURFACE('',#22836,3.E-1); -#22838=ORIENTED_EDGE('',*,*,#22343,.F.); -#22840=ORIENTED_EDGE('',*,*,#22839,.T.); -#22841=ORIENTED_EDGE('',*,*,#22767,.T.); -#22843=ORIENTED_EDGE('',*,*,#22842,.F.); -#22844=EDGE_LOOP('',(#22838,#22840,#22841,#22843)); -#22845=FACE_OUTER_BOUND('',#22844,.F.); -#22847=CARTESIAN_POINT('',(-1.75E0,-3.E-1,1.05E1)); -#22848=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22849=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22850=AXIS2_PLACEMENT_3D('',#22847,#22848,#22849); -#22851=CYLINDRICAL_SURFACE('',#22850,3.E-1); -#22852=ORIENTED_EDGE('',*,*,#22345,.F.); -#22853=ORIENTED_EDGE('',*,*,#22842,.T.); -#22854=ORIENTED_EDGE('',*,*,#22769,.T.); -#22855=ORIENTED_EDGE('',*,*,#22839,.F.); -#22856=EDGE_LOOP('',(#22852,#22853,#22854,#22855)); -#22857=FACE_OUTER_BOUND('',#22856,.F.); -#22859=CARTESIAN_POINT('',(2.75E0,-3.E-1,9.3E0)); -#22860=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22861=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22862=AXIS2_PLACEMENT_3D('',#22859,#22860,#22861); -#22863=CYLINDRICAL_SURFACE('',#22862,3.E-1); -#22864=ORIENTED_EDGE('',*,*,#22349,.F.); -#22866=ORIENTED_EDGE('',*,*,#22865,.T.); -#22868=ORIENTED_EDGE('',*,*,#22867,.T.); -#22870=ORIENTED_EDGE('',*,*,#22869,.F.); -#22871=EDGE_LOOP('',(#22864,#22866,#22868,#22870)); -#22872=FACE_OUTER_BOUND('',#22871,.F.); -#22874=CARTESIAN_POINT('',(2.75E0,-3.E-1,9.3E0)); -#22875=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22876=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22877=AXIS2_PLACEMENT_3D('',#22874,#22875,#22876); -#22878=CYLINDRICAL_SURFACE('',#22877,3.E-1); -#22879=ORIENTED_EDGE('',*,*,#22351,.F.); -#22880=ORIENTED_EDGE('',*,*,#22869,.T.); -#22882=ORIENTED_EDGE('',*,*,#22881,.T.); -#22883=ORIENTED_EDGE('',*,*,#22865,.F.); -#22884=EDGE_LOOP('',(#22879,#22880,#22882,#22883)); -#22885=FACE_OUTER_BOUND('',#22884,.F.); -#22887=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22888=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22889=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22890=AXIS2_PLACEMENT_3D('',#22887,#22888,#22889); -#22891=PLANE('',#22890); -#22892=ORIENTED_EDGE('',*,*,#22867,.F.); -#22893=ORIENTED_EDGE('',*,*,#22881,.F.); -#22894=EDGE_LOOP('',(#22892,#22893)); -#22895=FACE_OUTER_BOUND('',#22894,.F.); -#22897=FILL_AREA_STYLE_COLOUR('',#15); -#22898=FILL_AREA_STYLE('',(#22897)); -#22899=SURFACE_STYLE_FILL_AREA(#22898); -#22900=SURFACE_SIDE_STYLE('',(#22899)); -#22901=SURFACE_STYLE_USAGE(.POSITIVE.,#22900); -#22902=PRESENTATION_STYLE_ASSIGNMENT((#22901)); -#22903=STYLED_ITEM('',(#22902),#22896); -#22904=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22905=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22906=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22907=AXIS2_PLACEMENT_3D('',#22904,#22905,#22906); -#22908=PLANE('',#22907); -#22910=ORIENTED_EDGE('',*,*,#22909,.F.); -#22912=ORIENTED_EDGE('',*,*,#22911,.F.); -#22913=EDGE_LOOP('',(#22910,#22912)); -#22914=FACE_OUTER_BOUND('',#22913,.F.); -#22916=FILL_AREA_STYLE_COLOUR('',#15); -#22917=FILL_AREA_STYLE('',(#22916)); -#22918=SURFACE_STYLE_FILL_AREA(#22917); -#22919=SURFACE_SIDE_STYLE('',(#22918)); -#22920=SURFACE_STYLE_USAGE(.POSITIVE.,#22919); -#22921=PRESENTATION_STYLE_ASSIGNMENT((#22920)); -#22922=STYLED_ITEM('',(#22921),#22915); -#22923=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22924=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22925=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22926=AXIS2_PLACEMENT_3D('',#22923,#22924,#22925); -#22927=PLANE('',#22926); -#22929=ORIENTED_EDGE('',*,*,#22928,.F.); -#22931=ORIENTED_EDGE('',*,*,#22930,.F.); -#22932=EDGE_LOOP('',(#22929,#22931)); -#22933=FACE_OUTER_BOUND('',#22932,.F.); -#22935=FILL_AREA_STYLE_COLOUR('',#15); -#22936=FILL_AREA_STYLE('',(#22935)); -#22937=SURFACE_STYLE_FILL_AREA(#22936); -#22938=SURFACE_SIDE_STYLE('',(#22937)); -#22939=SURFACE_STYLE_USAGE(.POSITIVE.,#22938); -#22940=PRESENTATION_STYLE_ASSIGNMENT((#22939)); -#22941=STYLED_ITEM('',(#22940),#22934); -#22942=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#22943=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22944=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22945=AXIS2_PLACEMENT_3D('',#22942,#22943,#22944); -#22946=PLANE('',#22945); -#22948=ORIENTED_EDGE('',*,*,#22947,.F.); -#22950=ORIENTED_EDGE('',*,*,#22949,.F.); -#22951=EDGE_LOOP('',(#22948,#22950)); -#22952=FACE_OUTER_BOUND('',#22951,.F.); -#22954=FILL_AREA_STYLE_COLOUR('',#15); -#22955=FILL_AREA_STYLE('',(#22954)); -#22956=SURFACE_STYLE_FILL_AREA(#22955); -#22957=SURFACE_SIDE_STYLE('',(#22956)); -#22958=SURFACE_STYLE_USAGE(.POSITIVE.,#22957); -#22959=PRESENTATION_STYLE_ASSIGNMENT((#22958)); -#22960=STYLED_ITEM('',(#22959),#22953); -#22961=CARTESIAN_POINT('',(1.25E0,-3.E-1,9.3E0)); -#22962=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22963=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22964=AXIS2_PLACEMENT_3D('',#22961,#22962,#22963); -#22965=CYLINDRICAL_SURFACE('',#22964,3.E-1); -#22966=ORIENTED_EDGE('',*,*,#22355,.F.); -#22968=ORIENTED_EDGE('',*,*,#22967,.T.); -#22969=ORIENTED_EDGE('',*,*,#22909,.T.); -#22971=ORIENTED_EDGE('',*,*,#22970,.F.); -#22972=EDGE_LOOP('',(#22966,#22968,#22969,#22971)); -#22973=FACE_OUTER_BOUND('',#22972,.F.); -#22975=CARTESIAN_POINT('',(1.25E0,-3.E-1,9.3E0)); -#22976=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22977=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22978=AXIS2_PLACEMENT_3D('',#22975,#22976,#22977); -#22979=CYLINDRICAL_SURFACE('',#22978,3.E-1); -#22980=ORIENTED_EDGE('',*,*,#22357,.F.); -#22981=ORIENTED_EDGE('',*,*,#22970,.T.); -#22982=ORIENTED_EDGE('',*,*,#22911,.T.); -#22983=ORIENTED_EDGE('',*,*,#22967,.F.); -#22984=EDGE_LOOP('',(#22980,#22981,#22982,#22983)); -#22985=FACE_OUTER_BOUND('',#22984,.F.); -#22987=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,9.3E0)); -#22988=DIRECTION('',(0.E0,-1.E0,0.E0)); -#22989=DIRECTION('',(-1.E0,0.E0,0.E0)); -#22990=AXIS2_PLACEMENT_3D('',#22987,#22988,#22989); -#22991=CYLINDRICAL_SURFACE('',#22990,3.E-1); -#22992=ORIENTED_EDGE('',*,*,#22361,.F.); -#22994=ORIENTED_EDGE('',*,*,#22993,.T.); -#22995=ORIENTED_EDGE('',*,*,#22928,.T.); -#22997=ORIENTED_EDGE('',*,*,#22996,.F.); -#22998=EDGE_LOOP('',(#22992,#22994,#22995,#22997)); -#22999=FACE_OUTER_BOUND('',#22998,.F.); -#23001=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,9.3E0)); -#23002=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23003=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23004=AXIS2_PLACEMENT_3D('',#23001,#23002,#23003); -#23005=CYLINDRICAL_SURFACE('',#23004,3.E-1); -#23006=ORIENTED_EDGE('',*,*,#22363,.F.); -#23007=ORIENTED_EDGE('',*,*,#22996,.T.); -#23008=ORIENTED_EDGE('',*,*,#22930,.T.); -#23009=ORIENTED_EDGE('',*,*,#22993,.F.); -#23010=EDGE_LOOP('',(#23006,#23007,#23008,#23009)); -#23011=FACE_OUTER_BOUND('',#23010,.F.); -#23013=CARTESIAN_POINT('',(-1.75E0,-3.E-1,9.3E0)); -#23014=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23015=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23016=AXIS2_PLACEMENT_3D('',#23013,#23014,#23015); -#23017=CYLINDRICAL_SURFACE('',#23016,3.E-1); -#23018=ORIENTED_EDGE('',*,*,#22367,.F.); -#23020=ORIENTED_EDGE('',*,*,#23019,.T.); -#23021=ORIENTED_EDGE('',*,*,#22947,.T.); -#23023=ORIENTED_EDGE('',*,*,#23022,.F.); -#23024=EDGE_LOOP('',(#23018,#23020,#23021,#23023)); -#23025=FACE_OUTER_BOUND('',#23024,.F.); -#23027=CARTESIAN_POINT('',(-1.75E0,-3.E-1,9.3E0)); -#23028=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23029=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23030=AXIS2_PLACEMENT_3D('',#23027,#23028,#23029); -#23031=CYLINDRICAL_SURFACE('',#23030,3.E-1); -#23032=ORIENTED_EDGE('',*,*,#22369,.F.); -#23033=ORIENTED_EDGE('',*,*,#23022,.T.); -#23034=ORIENTED_EDGE('',*,*,#22949,.T.); -#23035=ORIENTED_EDGE('',*,*,#23019,.F.); -#23036=EDGE_LOOP('',(#23032,#23033,#23034,#23035)); -#23037=FACE_OUTER_BOUND('',#23036,.F.); -#23039=CARTESIAN_POINT('',(2.75E0,-3.E-1,8.1E0)); -#23040=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23041=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23042=AXIS2_PLACEMENT_3D('',#23039,#23040,#23041); -#23043=CYLINDRICAL_SURFACE('',#23042,3.E-1); -#23044=ORIENTED_EDGE('',*,*,#22373,.F.); -#23046=ORIENTED_EDGE('',*,*,#23045,.T.); -#23048=ORIENTED_EDGE('',*,*,#23047,.T.); -#23050=ORIENTED_EDGE('',*,*,#23049,.F.); -#23051=EDGE_LOOP('',(#23044,#23046,#23048,#23050)); -#23052=FACE_OUTER_BOUND('',#23051,.F.); -#23054=CARTESIAN_POINT('',(2.75E0,-3.E-1,8.1E0)); -#23055=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23056=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23057=AXIS2_PLACEMENT_3D('',#23054,#23055,#23056); -#23058=CYLINDRICAL_SURFACE('',#23057,3.E-1); -#23059=ORIENTED_EDGE('',*,*,#22375,.F.); -#23060=ORIENTED_EDGE('',*,*,#23049,.T.); -#23062=ORIENTED_EDGE('',*,*,#23061,.T.); -#23063=ORIENTED_EDGE('',*,*,#23045,.F.); -#23064=EDGE_LOOP('',(#23059,#23060,#23062,#23063)); -#23065=FACE_OUTER_BOUND('',#23064,.F.); -#23067=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23068=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23069=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23070=AXIS2_PLACEMENT_3D('',#23067,#23068,#23069); -#23071=PLANE('',#23070); -#23072=ORIENTED_EDGE('',*,*,#23047,.F.); -#23073=ORIENTED_EDGE('',*,*,#23061,.F.); -#23074=EDGE_LOOP('',(#23072,#23073)); -#23075=FACE_OUTER_BOUND('',#23074,.F.); -#23077=FILL_AREA_STYLE_COLOUR('',#15); -#23078=FILL_AREA_STYLE('',(#23077)); -#23079=SURFACE_STYLE_FILL_AREA(#23078); -#23080=SURFACE_SIDE_STYLE('',(#23079)); -#23081=SURFACE_STYLE_USAGE(.POSITIVE.,#23080); -#23082=PRESENTATION_STYLE_ASSIGNMENT((#23081)); -#23083=STYLED_ITEM('',(#23082),#23076); -#23084=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23085=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23086=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23087=AXIS2_PLACEMENT_3D('',#23084,#23085,#23086); -#23088=PLANE('',#23087); -#23090=ORIENTED_EDGE('',*,*,#23089,.F.); -#23092=ORIENTED_EDGE('',*,*,#23091,.F.); -#23093=EDGE_LOOP('',(#23090,#23092)); -#23094=FACE_OUTER_BOUND('',#23093,.F.); -#23096=FILL_AREA_STYLE_COLOUR('',#15); -#23097=FILL_AREA_STYLE('',(#23096)); -#23098=SURFACE_STYLE_FILL_AREA(#23097); -#23099=SURFACE_SIDE_STYLE('',(#23098)); -#23100=SURFACE_STYLE_USAGE(.POSITIVE.,#23099); -#23101=PRESENTATION_STYLE_ASSIGNMENT((#23100)); -#23102=STYLED_ITEM('',(#23101),#23095); -#23103=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23104=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23105=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23106=AXIS2_PLACEMENT_3D('',#23103,#23104,#23105); -#23107=PLANE('',#23106); -#23109=ORIENTED_EDGE('',*,*,#23108,.F.); -#23111=ORIENTED_EDGE('',*,*,#23110,.F.); -#23112=EDGE_LOOP('',(#23109,#23111)); -#23113=FACE_OUTER_BOUND('',#23112,.F.); -#23115=FILL_AREA_STYLE_COLOUR('',#15); -#23116=FILL_AREA_STYLE('',(#23115)); -#23117=SURFACE_STYLE_FILL_AREA(#23116); -#23118=SURFACE_SIDE_STYLE('',(#23117)); -#23119=SURFACE_STYLE_USAGE(.POSITIVE.,#23118); -#23120=PRESENTATION_STYLE_ASSIGNMENT((#23119)); -#23121=STYLED_ITEM('',(#23120),#23114); -#23122=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23123=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23124=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23125=AXIS2_PLACEMENT_3D('',#23122,#23123,#23124); -#23126=PLANE('',#23125); -#23128=ORIENTED_EDGE('',*,*,#23127,.F.); -#23130=ORIENTED_EDGE('',*,*,#23129,.F.); -#23131=EDGE_LOOP('',(#23128,#23130)); -#23132=FACE_OUTER_BOUND('',#23131,.F.); -#23134=FILL_AREA_STYLE_COLOUR('',#15); -#23135=FILL_AREA_STYLE('',(#23134)); -#23136=SURFACE_STYLE_FILL_AREA(#23135); -#23137=SURFACE_SIDE_STYLE('',(#23136)); -#23138=SURFACE_STYLE_USAGE(.POSITIVE.,#23137); -#23139=PRESENTATION_STYLE_ASSIGNMENT((#23138)); -#23140=STYLED_ITEM('',(#23139),#23133); -#23141=CARTESIAN_POINT('',(1.25E0,-3.E-1,8.1E0)); -#23142=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23143=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23144=AXIS2_PLACEMENT_3D('',#23141,#23142,#23143); -#23145=CYLINDRICAL_SURFACE('',#23144,3.E-1); -#23146=ORIENTED_EDGE('',*,*,#22379,.F.); -#23148=ORIENTED_EDGE('',*,*,#23147,.T.); -#23149=ORIENTED_EDGE('',*,*,#23089,.T.); -#23151=ORIENTED_EDGE('',*,*,#23150,.F.); -#23152=EDGE_LOOP('',(#23146,#23148,#23149,#23151)); -#23153=FACE_OUTER_BOUND('',#23152,.F.); -#23155=CARTESIAN_POINT('',(1.25E0,-3.E-1,8.1E0)); -#23156=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23157=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23158=AXIS2_PLACEMENT_3D('',#23155,#23156,#23157); -#23159=CYLINDRICAL_SURFACE('',#23158,3.E-1); -#23160=ORIENTED_EDGE('',*,*,#22381,.F.); -#23161=ORIENTED_EDGE('',*,*,#23150,.T.); -#23162=ORIENTED_EDGE('',*,*,#23091,.T.); -#23163=ORIENTED_EDGE('',*,*,#23147,.F.); -#23164=EDGE_LOOP('',(#23160,#23161,#23162,#23163)); -#23165=FACE_OUTER_BOUND('',#23164,.F.); -#23167=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,8.1E0)); -#23168=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23169=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23170=AXIS2_PLACEMENT_3D('',#23167,#23168,#23169); -#23171=CYLINDRICAL_SURFACE('',#23170,3.E-1); -#23172=ORIENTED_EDGE('',*,*,#22385,.F.); -#23174=ORIENTED_EDGE('',*,*,#23173,.T.); -#23175=ORIENTED_EDGE('',*,*,#23108,.T.); -#23177=ORIENTED_EDGE('',*,*,#23176,.F.); -#23178=EDGE_LOOP('',(#23172,#23174,#23175,#23177)); -#23179=FACE_OUTER_BOUND('',#23178,.F.); -#23181=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,8.1E0)); -#23182=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23183=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23184=AXIS2_PLACEMENT_3D('',#23181,#23182,#23183); -#23185=CYLINDRICAL_SURFACE('',#23184,3.E-1); -#23186=ORIENTED_EDGE('',*,*,#22387,.F.); -#23187=ORIENTED_EDGE('',*,*,#23176,.T.); -#23188=ORIENTED_EDGE('',*,*,#23110,.T.); -#23189=ORIENTED_EDGE('',*,*,#23173,.F.); -#23190=EDGE_LOOP('',(#23186,#23187,#23188,#23189)); -#23191=FACE_OUTER_BOUND('',#23190,.F.); -#23193=CARTESIAN_POINT('',(-1.75E0,-3.E-1,8.1E0)); -#23194=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23195=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23196=AXIS2_PLACEMENT_3D('',#23193,#23194,#23195); -#23197=CYLINDRICAL_SURFACE('',#23196,3.E-1); -#23198=ORIENTED_EDGE('',*,*,#22391,.F.); -#23200=ORIENTED_EDGE('',*,*,#23199,.T.); -#23201=ORIENTED_EDGE('',*,*,#23127,.T.); -#23203=ORIENTED_EDGE('',*,*,#23202,.F.); -#23204=EDGE_LOOP('',(#23198,#23200,#23201,#23203)); -#23205=FACE_OUTER_BOUND('',#23204,.F.); -#23207=CARTESIAN_POINT('',(-1.75E0,-3.E-1,8.1E0)); -#23208=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23209=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23210=AXIS2_PLACEMENT_3D('',#23207,#23208,#23209); -#23211=CYLINDRICAL_SURFACE('',#23210,3.E-1); -#23212=ORIENTED_EDGE('',*,*,#22393,.F.); -#23213=ORIENTED_EDGE('',*,*,#23202,.T.); -#23214=ORIENTED_EDGE('',*,*,#23129,.T.); -#23215=ORIENTED_EDGE('',*,*,#23199,.F.); -#23216=EDGE_LOOP('',(#23212,#23213,#23214,#23215)); -#23217=FACE_OUTER_BOUND('',#23216,.F.); -#23219=CARTESIAN_POINT('',(2.75E0,-3.E-1,6.9E0)); -#23220=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23221=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23222=AXIS2_PLACEMENT_3D('',#23219,#23220,#23221); -#23223=CYLINDRICAL_SURFACE('',#23222,3.E-1); -#23224=ORIENTED_EDGE('',*,*,#22397,.F.); -#23226=ORIENTED_EDGE('',*,*,#23225,.T.); -#23228=ORIENTED_EDGE('',*,*,#23227,.T.); -#23230=ORIENTED_EDGE('',*,*,#23229,.F.); -#23231=EDGE_LOOP('',(#23224,#23226,#23228,#23230)); -#23232=FACE_OUTER_BOUND('',#23231,.F.); -#23234=CARTESIAN_POINT('',(2.75E0,-3.E-1,6.9E0)); -#23235=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23236=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23237=AXIS2_PLACEMENT_3D('',#23234,#23235,#23236); -#23238=CYLINDRICAL_SURFACE('',#23237,3.E-1); -#23239=ORIENTED_EDGE('',*,*,#22399,.F.); -#23240=ORIENTED_EDGE('',*,*,#23229,.T.); -#23242=ORIENTED_EDGE('',*,*,#23241,.T.); -#23243=ORIENTED_EDGE('',*,*,#23225,.F.); -#23244=EDGE_LOOP('',(#23239,#23240,#23242,#23243)); -#23245=FACE_OUTER_BOUND('',#23244,.F.); -#23247=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23248=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23249=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23250=AXIS2_PLACEMENT_3D('',#23247,#23248,#23249); -#23251=PLANE('',#23250); -#23252=ORIENTED_EDGE('',*,*,#23227,.F.); -#23253=ORIENTED_EDGE('',*,*,#23241,.F.); -#23254=EDGE_LOOP('',(#23252,#23253)); -#23255=FACE_OUTER_BOUND('',#23254,.F.); -#23257=FILL_AREA_STYLE_COLOUR('',#15); -#23258=FILL_AREA_STYLE('',(#23257)); -#23259=SURFACE_STYLE_FILL_AREA(#23258); -#23260=SURFACE_SIDE_STYLE('',(#23259)); -#23261=SURFACE_STYLE_USAGE(.POSITIVE.,#23260); -#23262=PRESENTATION_STYLE_ASSIGNMENT((#23261)); -#23263=STYLED_ITEM('',(#23262),#23256); -#23264=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23265=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23266=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23267=AXIS2_PLACEMENT_3D('',#23264,#23265,#23266); -#23268=PLANE('',#23267); -#23270=ORIENTED_EDGE('',*,*,#23269,.F.); -#23272=ORIENTED_EDGE('',*,*,#23271,.F.); -#23273=EDGE_LOOP('',(#23270,#23272)); -#23274=FACE_OUTER_BOUND('',#23273,.F.); -#23276=FILL_AREA_STYLE_COLOUR('',#15); -#23277=FILL_AREA_STYLE('',(#23276)); -#23278=SURFACE_STYLE_FILL_AREA(#23277); -#23279=SURFACE_SIDE_STYLE('',(#23278)); -#23280=SURFACE_STYLE_USAGE(.POSITIVE.,#23279); -#23281=PRESENTATION_STYLE_ASSIGNMENT((#23280)); -#23282=STYLED_ITEM('',(#23281),#23275); -#23283=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23284=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23285=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23286=AXIS2_PLACEMENT_3D('',#23283,#23284,#23285); -#23287=PLANE('',#23286); -#23289=ORIENTED_EDGE('',*,*,#23288,.F.); -#23291=ORIENTED_EDGE('',*,*,#23290,.F.); -#23292=EDGE_LOOP('',(#23289,#23291)); -#23293=FACE_OUTER_BOUND('',#23292,.F.); -#23295=FILL_AREA_STYLE_COLOUR('',#15); -#23296=FILL_AREA_STYLE('',(#23295)); -#23297=SURFACE_STYLE_FILL_AREA(#23296); -#23298=SURFACE_SIDE_STYLE('',(#23297)); -#23299=SURFACE_STYLE_USAGE(.POSITIVE.,#23298); -#23300=PRESENTATION_STYLE_ASSIGNMENT((#23299)); -#23301=STYLED_ITEM('',(#23300),#23294); -#23302=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23303=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23304=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23305=AXIS2_PLACEMENT_3D('',#23302,#23303,#23304); -#23306=PLANE('',#23305); -#23308=ORIENTED_EDGE('',*,*,#23307,.F.); -#23310=ORIENTED_EDGE('',*,*,#23309,.F.); -#23311=EDGE_LOOP('',(#23308,#23310)); -#23312=FACE_OUTER_BOUND('',#23311,.F.); -#23314=FILL_AREA_STYLE_COLOUR('',#15); -#23315=FILL_AREA_STYLE('',(#23314)); -#23316=SURFACE_STYLE_FILL_AREA(#23315); -#23317=SURFACE_SIDE_STYLE('',(#23316)); -#23318=SURFACE_STYLE_USAGE(.POSITIVE.,#23317); -#23319=PRESENTATION_STYLE_ASSIGNMENT((#23318)); -#23320=STYLED_ITEM('',(#23319),#23313); -#23321=CARTESIAN_POINT('',(1.25E0,-3.E-1,6.9E0)); -#23322=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23323=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23324=AXIS2_PLACEMENT_3D('',#23321,#23322,#23323); -#23325=CYLINDRICAL_SURFACE('',#23324,3.E-1); -#23326=ORIENTED_EDGE('',*,*,#22403,.F.); -#23328=ORIENTED_EDGE('',*,*,#23327,.T.); -#23329=ORIENTED_EDGE('',*,*,#23269,.T.); -#23331=ORIENTED_EDGE('',*,*,#23330,.F.); -#23332=EDGE_LOOP('',(#23326,#23328,#23329,#23331)); -#23333=FACE_OUTER_BOUND('',#23332,.F.); -#23335=CARTESIAN_POINT('',(1.25E0,-3.E-1,6.9E0)); -#23336=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23337=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23338=AXIS2_PLACEMENT_3D('',#23335,#23336,#23337); -#23339=CYLINDRICAL_SURFACE('',#23338,3.E-1); -#23340=ORIENTED_EDGE('',*,*,#22405,.F.); -#23341=ORIENTED_EDGE('',*,*,#23330,.T.); -#23342=ORIENTED_EDGE('',*,*,#23271,.T.); -#23343=ORIENTED_EDGE('',*,*,#23327,.F.); -#23344=EDGE_LOOP('',(#23340,#23341,#23342,#23343)); -#23345=FACE_OUTER_BOUND('',#23344,.F.); -#23347=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,6.9E0)); -#23348=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23349=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23350=AXIS2_PLACEMENT_3D('',#23347,#23348,#23349); -#23351=CYLINDRICAL_SURFACE('',#23350,3.E-1); -#23352=ORIENTED_EDGE('',*,*,#22409,.F.); -#23354=ORIENTED_EDGE('',*,*,#23353,.T.); -#23355=ORIENTED_EDGE('',*,*,#23288,.T.); -#23357=ORIENTED_EDGE('',*,*,#23356,.F.); -#23358=EDGE_LOOP('',(#23352,#23354,#23355,#23357)); -#23359=FACE_OUTER_BOUND('',#23358,.F.); -#23361=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,6.9E0)); -#23362=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23363=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23364=AXIS2_PLACEMENT_3D('',#23361,#23362,#23363); -#23365=CYLINDRICAL_SURFACE('',#23364,3.E-1); -#23366=ORIENTED_EDGE('',*,*,#22411,.F.); -#23367=ORIENTED_EDGE('',*,*,#23356,.T.); -#23368=ORIENTED_EDGE('',*,*,#23290,.T.); -#23369=ORIENTED_EDGE('',*,*,#23353,.F.); -#23370=EDGE_LOOP('',(#23366,#23367,#23368,#23369)); -#23371=FACE_OUTER_BOUND('',#23370,.F.); -#23373=CARTESIAN_POINT('',(-1.75E0,-3.E-1,6.9E0)); -#23374=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23375=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23376=AXIS2_PLACEMENT_3D('',#23373,#23374,#23375); -#23377=CYLINDRICAL_SURFACE('',#23376,3.E-1); -#23378=ORIENTED_EDGE('',*,*,#22415,.F.); -#23380=ORIENTED_EDGE('',*,*,#23379,.T.); -#23381=ORIENTED_EDGE('',*,*,#23307,.T.); -#23383=ORIENTED_EDGE('',*,*,#23382,.F.); -#23384=EDGE_LOOP('',(#23378,#23380,#23381,#23383)); -#23385=FACE_OUTER_BOUND('',#23384,.F.); -#23387=CARTESIAN_POINT('',(-1.75E0,-3.E-1,6.9E0)); -#23388=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23389=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23390=AXIS2_PLACEMENT_3D('',#23387,#23388,#23389); -#23391=CYLINDRICAL_SURFACE('',#23390,3.E-1); -#23392=ORIENTED_EDGE('',*,*,#22417,.F.); -#23393=ORIENTED_EDGE('',*,*,#23382,.T.); -#23394=ORIENTED_EDGE('',*,*,#23309,.T.); -#23395=ORIENTED_EDGE('',*,*,#23379,.F.); -#23396=EDGE_LOOP('',(#23392,#23393,#23394,#23395)); -#23397=FACE_OUTER_BOUND('',#23396,.F.); -#23399=CARTESIAN_POINT('',(2.75E0,-3.E-1,5.7E0)); -#23400=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23401=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23402=AXIS2_PLACEMENT_3D('',#23399,#23400,#23401); -#23403=CYLINDRICAL_SURFACE('',#23402,3.E-1); -#23404=ORIENTED_EDGE('',*,*,#22421,.F.); -#23406=ORIENTED_EDGE('',*,*,#23405,.T.); -#23408=ORIENTED_EDGE('',*,*,#23407,.T.); -#23410=ORIENTED_EDGE('',*,*,#23409,.F.); -#23411=EDGE_LOOP('',(#23404,#23406,#23408,#23410)); -#23412=FACE_OUTER_BOUND('',#23411,.F.); -#23414=CARTESIAN_POINT('',(2.75E0,-3.E-1,5.7E0)); -#23415=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23416=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23417=AXIS2_PLACEMENT_3D('',#23414,#23415,#23416); -#23418=CYLINDRICAL_SURFACE('',#23417,3.E-1); -#23419=ORIENTED_EDGE('',*,*,#22423,.F.); -#23420=ORIENTED_EDGE('',*,*,#23409,.T.); -#23422=ORIENTED_EDGE('',*,*,#23421,.T.); -#23423=ORIENTED_EDGE('',*,*,#23405,.F.); -#23424=EDGE_LOOP('',(#23419,#23420,#23422,#23423)); -#23425=FACE_OUTER_BOUND('',#23424,.F.); -#23427=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23428=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23429=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23430=AXIS2_PLACEMENT_3D('',#23427,#23428,#23429); -#23431=PLANE('',#23430); -#23432=ORIENTED_EDGE('',*,*,#23407,.F.); -#23433=ORIENTED_EDGE('',*,*,#23421,.F.); -#23434=EDGE_LOOP('',(#23432,#23433)); -#23435=FACE_OUTER_BOUND('',#23434,.F.); -#23437=FILL_AREA_STYLE_COLOUR('',#15); -#23438=FILL_AREA_STYLE('',(#23437)); -#23439=SURFACE_STYLE_FILL_AREA(#23438); -#23440=SURFACE_SIDE_STYLE('',(#23439)); -#23441=SURFACE_STYLE_USAGE(.POSITIVE.,#23440); -#23442=PRESENTATION_STYLE_ASSIGNMENT((#23441)); -#23443=STYLED_ITEM('',(#23442),#23436); -#23444=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23445=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23446=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23447=AXIS2_PLACEMENT_3D('',#23444,#23445,#23446); -#23448=PLANE('',#23447); -#23450=ORIENTED_EDGE('',*,*,#23449,.F.); -#23452=ORIENTED_EDGE('',*,*,#23451,.F.); -#23453=EDGE_LOOP('',(#23450,#23452)); -#23454=FACE_OUTER_BOUND('',#23453,.F.); -#23456=FILL_AREA_STYLE_COLOUR('',#15); -#23457=FILL_AREA_STYLE('',(#23456)); -#23458=SURFACE_STYLE_FILL_AREA(#23457); -#23459=SURFACE_SIDE_STYLE('',(#23458)); -#23460=SURFACE_STYLE_USAGE(.POSITIVE.,#23459); -#23461=PRESENTATION_STYLE_ASSIGNMENT((#23460)); -#23462=STYLED_ITEM('',(#23461),#23455); -#23463=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23464=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23465=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23466=AXIS2_PLACEMENT_3D('',#23463,#23464,#23465); -#23467=PLANE('',#23466); -#23469=ORIENTED_EDGE('',*,*,#23468,.F.); -#23471=ORIENTED_EDGE('',*,*,#23470,.F.); -#23472=EDGE_LOOP('',(#23469,#23471)); -#23473=FACE_OUTER_BOUND('',#23472,.F.); -#23475=FILL_AREA_STYLE_COLOUR('',#15); -#23476=FILL_AREA_STYLE('',(#23475)); -#23477=SURFACE_STYLE_FILL_AREA(#23476); -#23478=SURFACE_SIDE_STYLE('',(#23477)); -#23479=SURFACE_STYLE_USAGE(.POSITIVE.,#23478); -#23480=PRESENTATION_STYLE_ASSIGNMENT((#23479)); -#23481=STYLED_ITEM('',(#23480),#23474); -#23482=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23483=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23484=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23485=AXIS2_PLACEMENT_3D('',#23482,#23483,#23484); -#23486=PLANE('',#23485); -#23488=ORIENTED_EDGE('',*,*,#23487,.F.); -#23490=ORIENTED_EDGE('',*,*,#23489,.F.); -#23491=EDGE_LOOP('',(#23488,#23490)); -#23492=FACE_OUTER_BOUND('',#23491,.F.); -#23494=FILL_AREA_STYLE_COLOUR('',#15); -#23495=FILL_AREA_STYLE('',(#23494)); -#23496=SURFACE_STYLE_FILL_AREA(#23495); -#23497=SURFACE_SIDE_STYLE('',(#23496)); -#23498=SURFACE_STYLE_USAGE(.POSITIVE.,#23497); -#23499=PRESENTATION_STYLE_ASSIGNMENT((#23498)); -#23500=STYLED_ITEM('',(#23499),#23493); -#23501=CARTESIAN_POINT('',(1.25E0,-3.E-1,5.7E0)); -#23502=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23503=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23504=AXIS2_PLACEMENT_3D('',#23501,#23502,#23503); -#23505=CYLINDRICAL_SURFACE('',#23504,3.E-1); -#23506=ORIENTED_EDGE('',*,*,#22427,.F.); -#23508=ORIENTED_EDGE('',*,*,#23507,.T.); -#23509=ORIENTED_EDGE('',*,*,#23449,.T.); -#23511=ORIENTED_EDGE('',*,*,#23510,.F.); -#23512=EDGE_LOOP('',(#23506,#23508,#23509,#23511)); -#23513=FACE_OUTER_BOUND('',#23512,.F.); -#23515=CARTESIAN_POINT('',(1.25E0,-3.E-1,5.7E0)); -#23516=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23517=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23518=AXIS2_PLACEMENT_3D('',#23515,#23516,#23517); -#23519=CYLINDRICAL_SURFACE('',#23518,3.E-1); -#23520=ORIENTED_EDGE('',*,*,#22429,.F.); -#23521=ORIENTED_EDGE('',*,*,#23510,.T.); -#23522=ORIENTED_EDGE('',*,*,#23451,.T.); -#23523=ORIENTED_EDGE('',*,*,#23507,.F.); -#23524=EDGE_LOOP('',(#23520,#23521,#23522,#23523)); -#23525=FACE_OUTER_BOUND('',#23524,.F.); -#23527=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,5.7E0)); -#23528=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23529=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23530=AXIS2_PLACEMENT_3D('',#23527,#23528,#23529); -#23531=CYLINDRICAL_SURFACE('',#23530,3.E-1); -#23532=ORIENTED_EDGE('',*,*,#22433,.F.); -#23534=ORIENTED_EDGE('',*,*,#23533,.T.); -#23535=ORIENTED_EDGE('',*,*,#23468,.T.); -#23537=ORIENTED_EDGE('',*,*,#23536,.F.); -#23538=EDGE_LOOP('',(#23532,#23534,#23535,#23537)); -#23539=FACE_OUTER_BOUND('',#23538,.F.); -#23541=CARTESIAN_POINT('',(-2.5E-1,-3.E-1,5.7E0)); -#23542=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23543=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23544=AXIS2_PLACEMENT_3D('',#23541,#23542,#23543); -#23545=CYLINDRICAL_SURFACE('',#23544,3.E-1); -#23546=ORIENTED_EDGE('',*,*,#22435,.F.); -#23547=ORIENTED_EDGE('',*,*,#23536,.T.); -#23548=ORIENTED_EDGE('',*,*,#23470,.T.); -#23549=ORIENTED_EDGE('',*,*,#23533,.F.); -#23550=EDGE_LOOP('',(#23546,#23547,#23548,#23549)); -#23551=FACE_OUTER_BOUND('',#23550,.F.); -#23553=CARTESIAN_POINT('',(-1.75E0,-3.E-1,5.7E0)); -#23554=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23555=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23556=AXIS2_PLACEMENT_3D('',#23553,#23554,#23555); -#23557=CYLINDRICAL_SURFACE('',#23556,3.E-1); -#23558=ORIENTED_EDGE('',*,*,#22439,.F.); -#23560=ORIENTED_EDGE('',*,*,#23559,.T.); -#23561=ORIENTED_EDGE('',*,*,#23487,.T.); -#23563=ORIENTED_EDGE('',*,*,#23562,.F.); -#23564=EDGE_LOOP('',(#23558,#23560,#23561,#23563)); -#23565=FACE_OUTER_BOUND('',#23564,.F.); -#23567=CARTESIAN_POINT('',(-1.75E0,-3.E-1,5.7E0)); -#23568=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23569=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23570=AXIS2_PLACEMENT_3D('',#23567,#23568,#23569); -#23571=CYLINDRICAL_SURFACE('',#23570,3.E-1); -#23572=ORIENTED_EDGE('',*,*,#22441,.F.); -#23573=ORIENTED_EDGE('',*,*,#23562,.T.); -#23574=ORIENTED_EDGE('',*,*,#23489,.T.); -#23575=ORIENTED_EDGE('',*,*,#23559,.F.); -#23576=EDGE_LOOP('',(#23572,#23573,#23574,#23575)); -#23577=FACE_OUTER_BOUND('',#23576,.F.); -#23579=CARTESIAN_POINT('',(4.625E0,-3.E-1,2.95E0)); -#23580=DIRECTION('',(1.E0,0.E0,0.E0)); -#23581=DIRECTION('',(0.E0,0.E0,1.E0)); -#23582=AXIS2_PLACEMENT_3D('',#23579,#23580,#23581); -#23583=PLANE('',#23582); -#23584=ORIENTED_EDGE('',*,*,#22445,.F.); -#23586=ORIENTED_EDGE('',*,*,#23585,.T.); -#23588=ORIENTED_EDGE('',*,*,#23587,.T.); -#23590=ORIENTED_EDGE('',*,*,#23589,.F.); -#23591=EDGE_LOOP('',(#23584,#23586,#23588,#23590)); -#23592=FACE_OUTER_BOUND('',#23591,.F.); -#23594=CARTESIAN_POINT('',(3.125E0,-3.E-1,2.95E0)); -#23595=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23596=DIRECTION('',(1.E0,0.E0,0.E0)); -#23597=AXIS2_PLACEMENT_3D('',#23594,#23595,#23596); -#23598=PLANE('',#23597); -#23599=ORIENTED_EDGE('',*,*,#22451,.F.); -#23601=ORIENTED_EDGE('',*,*,#23600,.T.); -#23603=ORIENTED_EDGE('',*,*,#23602,.T.); -#23604=ORIENTED_EDGE('',*,*,#23585,.F.); -#23605=EDGE_LOOP('',(#23599,#23601,#23603,#23604)); -#23606=FACE_OUTER_BOUND('',#23605,.F.); -#23608=CARTESIAN_POINT('',(3.125E0,-3.E-1,4.45E0)); -#23609=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23610=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23611=AXIS2_PLACEMENT_3D('',#23608,#23609,#23610); -#23612=PLANE('',#23611); -#23613=ORIENTED_EDGE('',*,*,#22449,.F.); -#23615=ORIENTED_EDGE('',*,*,#23614,.T.); -#23617=ORIENTED_EDGE('',*,*,#23616,.T.); -#23618=ORIENTED_EDGE('',*,*,#23600,.F.); -#23619=EDGE_LOOP('',(#23613,#23615,#23617,#23618)); -#23620=FACE_OUTER_BOUND('',#23619,.F.); -#23622=CARTESIAN_POINT('',(4.625E0,-3.E-1,4.45E0)); -#23623=DIRECTION('',(0.E0,0.E0,1.E0)); -#23624=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23625=AXIS2_PLACEMENT_3D('',#23622,#23623,#23624); -#23626=PLANE('',#23625); -#23627=ORIENTED_EDGE('',*,*,#22447,.F.); -#23628=ORIENTED_EDGE('',*,*,#23589,.T.); -#23630=ORIENTED_EDGE('',*,*,#23629,.T.); -#23631=ORIENTED_EDGE('',*,*,#23614,.F.); -#23632=EDGE_LOOP('',(#23627,#23628,#23630,#23631)); -#23633=FACE_OUTER_BOUND('',#23632,.F.); -#23635=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23636=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23637=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23638=AXIS2_PLACEMENT_3D('',#23635,#23636,#23637); -#23639=PLANE('',#23638); -#23640=ORIENTED_EDGE('',*,*,#23587,.F.); -#23641=ORIENTED_EDGE('',*,*,#23602,.F.); -#23642=ORIENTED_EDGE('',*,*,#23616,.F.); -#23643=ORIENTED_EDGE('',*,*,#23629,.F.); -#23644=EDGE_LOOP('',(#23640,#23641,#23642,#23643)); -#23645=FACE_OUTER_BOUND('',#23644,.F.); -#23647=FILL_AREA_STYLE_COLOUR('',#15); -#23648=FILL_AREA_STYLE('',(#23647)); -#23649=SURFACE_STYLE_FILL_AREA(#23648); -#23650=SURFACE_SIDE_STYLE('',(#23649)); -#23651=SURFACE_STYLE_USAGE(.POSITIVE.,#23650); -#23652=PRESENTATION_STYLE_ASSIGNMENT((#23651)); -#23653=STYLED_ITEM('',(#23652),#23646); -#23654=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23655=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23656=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23657=AXIS2_PLACEMENT_3D('',#23654,#23655,#23656); -#23658=PLANE('',#23657); -#23660=ORIENTED_EDGE('',*,*,#23659,.F.); -#23662=ORIENTED_EDGE('',*,*,#23661,.F.); -#23664=ORIENTED_EDGE('',*,*,#23663,.F.); -#23666=ORIENTED_EDGE('',*,*,#23665,.F.); -#23667=EDGE_LOOP('',(#23660,#23662,#23664,#23666)); -#23668=FACE_OUTER_BOUND('',#23667,.F.); -#23670=FILL_AREA_STYLE_COLOUR('',#15); -#23671=FILL_AREA_STYLE('',(#23670)); -#23672=SURFACE_STYLE_FILL_AREA(#23671); -#23673=SURFACE_SIDE_STYLE('',(#23672)); -#23674=SURFACE_STYLE_USAGE(.POSITIVE.,#23673); -#23675=PRESENTATION_STYLE_ASSIGNMENT((#23674)); -#23676=STYLED_ITEM('',(#23675),#23669); -#23677=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23678=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23679=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23680=AXIS2_PLACEMENT_3D('',#23677,#23678,#23679); -#23681=PLANE('',#23680); -#23683=ORIENTED_EDGE('',*,*,#23682,.F.); -#23685=ORIENTED_EDGE('',*,*,#23684,.F.); -#23687=ORIENTED_EDGE('',*,*,#23686,.F.); -#23689=ORIENTED_EDGE('',*,*,#23688,.F.); -#23690=EDGE_LOOP('',(#23683,#23685,#23687,#23689)); -#23691=FACE_OUTER_BOUND('',#23690,.F.); -#23693=FILL_AREA_STYLE_COLOUR('',#15); -#23694=FILL_AREA_STYLE('',(#23693)); -#23695=SURFACE_STYLE_FILL_AREA(#23694); -#23696=SURFACE_SIDE_STYLE('',(#23695)); -#23697=SURFACE_STYLE_USAGE(.POSITIVE.,#23696); -#23698=PRESENTATION_STYLE_ASSIGNMENT((#23697)); -#23699=STYLED_ITEM('',(#23698),#23692); -#23700=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23701=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23702=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23703=AXIS2_PLACEMENT_3D('',#23700,#23701,#23702); -#23704=PLANE('',#23703); -#23706=ORIENTED_EDGE('',*,*,#23705,.F.); -#23708=ORIENTED_EDGE('',*,*,#23707,.F.); -#23710=ORIENTED_EDGE('',*,*,#23709,.F.); -#23712=ORIENTED_EDGE('',*,*,#23711,.F.); -#23713=EDGE_LOOP('',(#23706,#23708,#23710,#23712)); -#23714=FACE_OUTER_BOUND('',#23713,.F.); -#23716=FILL_AREA_STYLE_COLOUR('',#15); -#23717=FILL_AREA_STYLE('',(#23716)); -#23718=SURFACE_STYLE_FILL_AREA(#23717); -#23719=SURFACE_SIDE_STYLE('',(#23718)); -#23720=SURFACE_STYLE_USAGE(.POSITIVE.,#23719); -#23721=PRESENTATION_STYLE_ASSIGNMENT((#23720)); -#23722=STYLED_ITEM('',(#23721),#23715); -#23723=CARTESIAN_POINT('',(2.375E0,-3.E-1,2.95E0)); -#23724=DIRECTION('',(1.E0,0.E0,0.E0)); -#23725=DIRECTION('',(0.E0,0.E0,1.E0)); -#23726=AXIS2_PLACEMENT_3D('',#23723,#23724,#23725); -#23727=PLANE('',#23726); -#23728=ORIENTED_EDGE('',*,*,#22455,.F.); -#23730=ORIENTED_EDGE('',*,*,#23729,.T.); -#23731=ORIENTED_EDGE('',*,*,#23659,.T.); -#23733=ORIENTED_EDGE('',*,*,#23732,.F.); -#23734=EDGE_LOOP('',(#23728,#23730,#23731,#23733)); -#23735=FACE_OUTER_BOUND('',#23734,.F.); -#23737=CARTESIAN_POINT('',(8.75E-1,-3.E-1,2.95E0)); -#23738=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23739=DIRECTION('',(1.E0,0.E0,0.E0)); -#23740=AXIS2_PLACEMENT_3D('',#23737,#23738,#23739); -#23741=PLANE('',#23740); -#23742=ORIENTED_EDGE('',*,*,#22461,.F.); -#23744=ORIENTED_EDGE('',*,*,#23743,.T.); -#23745=ORIENTED_EDGE('',*,*,#23661,.T.); -#23746=ORIENTED_EDGE('',*,*,#23729,.F.); -#23747=EDGE_LOOP('',(#23742,#23744,#23745,#23746)); -#23748=FACE_OUTER_BOUND('',#23747,.F.); -#23750=CARTESIAN_POINT('',(8.75E-1,-3.E-1,4.45E0)); -#23751=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23752=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23753=AXIS2_PLACEMENT_3D('',#23750,#23751,#23752); -#23754=PLANE('',#23753); -#23755=ORIENTED_EDGE('',*,*,#22459,.F.); -#23757=ORIENTED_EDGE('',*,*,#23756,.T.); -#23758=ORIENTED_EDGE('',*,*,#23663,.T.); -#23759=ORIENTED_EDGE('',*,*,#23743,.F.); -#23760=EDGE_LOOP('',(#23755,#23757,#23758,#23759)); -#23761=FACE_OUTER_BOUND('',#23760,.F.); -#23763=CARTESIAN_POINT('',(2.375E0,-3.E-1,4.45E0)); -#23764=DIRECTION('',(0.E0,0.E0,1.E0)); -#23765=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23766=AXIS2_PLACEMENT_3D('',#23763,#23764,#23765); -#23767=PLANE('',#23766); -#23768=ORIENTED_EDGE('',*,*,#22457,.F.); -#23769=ORIENTED_EDGE('',*,*,#23732,.T.); -#23770=ORIENTED_EDGE('',*,*,#23665,.T.); -#23771=ORIENTED_EDGE('',*,*,#23756,.F.); -#23772=EDGE_LOOP('',(#23768,#23769,#23770,#23771)); -#23773=FACE_OUTER_BOUND('',#23772,.F.); -#23775=CARTESIAN_POINT('',(-3.625E0,-3.E-1,2.95E0)); -#23776=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23777=DIRECTION('',(1.E0,0.E0,0.E0)); -#23778=AXIS2_PLACEMENT_3D('',#23775,#23776,#23777); -#23779=PLANE('',#23778); -#23780=ORIENTED_EDGE('',*,*,#22465,.F.); -#23782=ORIENTED_EDGE('',*,*,#23781,.T.); -#23783=ORIENTED_EDGE('',*,*,#23682,.T.); -#23785=ORIENTED_EDGE('',*,*,#23784,.F.); -#23786=EDGE_LOOP('',(#23780,#23782,#23783,#23785)); -#23787=FACE_OUTER_BOUND('',#23786,.F.); -#23789=CARTESIAN_POINT('',(-3.625E0,-3.E-1,4.45E0)); -#23790=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23791=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23792=AXIS2_PLACEMENT_3D('',#23789,#23790,#23791); -#23793=PLANE('',#23792); -#23794=ORIENTED_EDGE('',*,*,#22471,.F.); -#23796=ORIENTED_EDGE('',*,*,#23795,.T.); -#23797=ORIENTED_EDGE('',*,*,#23684,.T.); -#23798=ORIENTED_EDGE('',*,*,#23781,.F.); -#23799=EDGE_LOOP('',(#23794,#23796,#23797,#23798)); -#23800=FACE_OUTER_BOUND('',#23799,.F.); -#23802=CARTESIAN_POINT('',(-2.125E0,-3.E-1,4.45E0)); -#23803=DIRECTION('',(0.E0,0.E0,1.E0)); -#23804=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23805=AXIS2_PLACEMENT_3D('',#23802,#23803,#23804); -#23806=PLANE('',#23805); -#23807=ORIENTED_EDGE('',*,*,#22469,.F.); -#23809=ORIENTED_EDGE('',*,*,#23808,.T.); -#23810=ORIENTED_EDGE('',*,*,#23686,.T.); -#23811=ORIENTED_EDGE('',*,*,#23795,.F.); -#23812=EDGE_LOOP('',(#23807,#23809,#23810,#23811)); -#23813=FACE_OUTER_BOUND('',#23812,.F.); -#23815=CARTESIAN_POINT('',(-2.125E0,-3.E-1,2.95E0)); -#23816=DIRECTION('',(1.E0,0.E0,0.E0)); -#23817=DIRECTION('',(0.E0,0.E0,1.E0)); -#23818=AXIS2_PLACEMENT_3D('',#23815,#23816,#23817); -#23819=PLANE('',#23818); -#23820=ORIENTED_EDGE('',*,*,#22467,.F.); -#23821=ORIENTED_EDGE('',*,*,#23784,.T.); -#23822=ORIENTED_EDGE('',*,*,#23688,.T.); -#23823=ORIENTED_EDGE('',*,*,#23808,.F.); -#23824=EDGE_LOOP('',(#23820,#23821,#23822,#23823)); -#23825=FACE_OUTER_BOUND('',#23824,.F.); -#23827=CARTESIAN_POINT('',(-1.375E0,-3.E-1,2.95E0)); -#23828=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23829=DIRECTION('',(1.E0,0.E0,0.E0)); -#23830=AXIS2_PLACEMENT_3D('',#23827,#23828,#23829); -#23831=PLANE('',#23830); -#23832=ORIENTED_EDGE('',*,*,#22475,.F.); -#23834=ORIENTED_EDGE('',*,*,#23833,.T.); -#23835=ORIENTED_EDGE('',*,*,#23705,.T.); -#23837=ORIENTED_EDGE('',*,*,#23836,.F.); -#23838=EDGE_LOOP('',(#23832,#23834,#23835,#23837)); -#23839=FACE_OUTER_BOUND('',#23838,.F.); -#23841=CARTESIAN_POINT('',(-1.375E0,-3.E-1,4.45E0)); -#23842=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23843=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23844=AXIS2_PLACEMENT_3D('',#23841,#23842,#23843); -#23845=PLANE('',#23844); -#23846=ORIENTED_EDGE('',*,*,#22481,.F.); -#23848=ORIENTED_EDGE('',*,*,#23847,.T.); -#23849=ORIENTED_EDGE('',*,*,#23707,.T.); -#23850=ORIENTED_EDGE('',*,*,#23833,.F.); -#23851=EDGE_LOOP('',(#23846,#23848,#23849,#23850)); -#23852=FACE_OUTER_BOUND('',#23851,.F.); -#23854=CARTESIAN_POINT('',(1.25E-1,-3.E-1,4.45E0)); -#23855=DIRECTION('',(0.E0,0.E0,1.E0)); -#23856=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23857=AXIS2_PLACEMENT_3D('',#23854,#23855,#23856); -#23858=PLANE('',#23857); -#23859=ORIENTED_EDGE('',*,*,#22479,.F.); -#23861=ORIENTED_EDGE('',*,*,#23860,.T.); -#23862=ORIENTED_EDGE('',*,*,#23709,.T.); -#23863=ORIENTED_EDGE('',*,*,#23847,.F.); -#23864=EDGE_LOOP('',(#23859,#23861,#23862,#23863)); -#23865=FACE_OUTER_BOUND('',#23864,.F.); -#23867=CARTESIAN_POINT('',(1.25E-1,-3.E-1,2.95E0)); -#23868=DIRECTION('',(1.E0,0.E0,0.E0)); -#23869=DIRECTION('',(0.E0,0.E0,1.E0)); -#23870=AXIS2_PLACEMENT_3D('',#23867,#23868,#23869); -#23871=PLANE('',#23870); -#23872=ORIENTED_EDGE('',*,*,#22477,.F.); -#23873=ORIENTED_EDGE('',*,*,#23836,.T.); -#23874=ORIENTED_EDGE('',*,*,#23711,.T.); -#23875=ORIENTED_EDGE('',*,*,#23860,.F.); -#23876=EDGE_LOOP('',(#23872,#23873,#23874,#23875)); -#23877=FACE_OUTER_BOUND('',#23876,.F.); -#23879=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.4035E1)); -#23880=DIRECTION('',(1.E0,0.E0,0.E0)); -#23881=DIRECTION('',(0.E0,0.E0,1.E0)); -#23882=AXIS2_PLACEMENT_3D('',#23879,#23880,#23881); -#23883=PLANE('',#23882); -#23884=ORIENTED_EDGE('',*,*,#22141,.F.); -#23886=ORIENTED_EDGE('',*,*,#23885,.T.); -#23888=ORIENTED_EDGE('',*,*,#23887,.T.); -#23890=ORIENTED_EDGE('',*,*,#23889,.F.); -#23891=EDGE_LOOP('',(#23884,#23886,#23888,#23890)); -#23892=FACE_OUTER_BOUND('',#23891,.F.); -#23894=CARTESIAN_POINT('',(-7.64E0,-3.E-1,-1.4035E1)); -#23895=DIRECTION('',(0.E0,0.E0,-1.E0)); -#23896=DIRECTION('',(1.E0,0.E0,0.E0)); -#23897=AXIS2_PLACEMENT_3D('',#23894,#23895,#23896); -#23898=PLANE('',#23897); -#23899=ORIENTED_EDGE('',*,*,#22303,.F.); -#23901=ORIENTED_EDGE('',*,*,#23900,.T.); -#23903=ORIENTED_EDGE('',*,*,#23902,.T.); -#23904=ORIENTED_EDGE('',*,*,#23885,.F.); -#23905=EDGE_LOOP('',(#23899,#23901,#23903,#23904)); -#23906=FACE_OUTER_BOUND('',#23905,.F.); -#23908=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#23909=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23910=DIRECTION('',(0.E0,0.E0,1.E0)); -#23911=AXIS2_PLACEMENT_3D('',#23908,#23909,#23910); -#23912=PLANE('',#23911); -#23914=ORIENTED_EDGE('',*,*,#23913,.T.); -#23916=ORIENTED_EDGE('',*,*,#23915,.T.); -#23918=ORIENTED_EDGE('',*,*,#23917,.T.); -#23920=ORIENTED_EDGE('',*,*,#23919,.F.); -#23921=ORIENTED_EDGE('',*,*,#22161,.F.); -#23923=ORIENTED_EDGE('',*,*,#23922,.T.); -#23924=EDGE_LOOP('',(#23914,#23916,#23918,#23920,#23921,#23923)); -#23925=FACE_OUTER_BOUND('',#23924,.F.); -#23927=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#23928=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23929=DIRECTION('',(0.E0,0.E0,1.E0)); -#23930=AXIS2_PLACEMENT_3D('',#23927,#23928,#23929); -#23931=PLANE('',#23930); -#23933=ORIENTED_EDGE('',*,*,#23932,.T.); -#23935=ORIENTED_EDGE('',*,*,#23934,.F.); -#23936=ORIENTED_EDGE('',*,*,#22153,.F.); -#23938=ORIENTED_EDGE('',*,*,#23937,.T.); -#23940=ORIENTED_EDGE('',*,*,#23939,.T.); -#23942=ORIENTED_EDGE('',*,*,#23941,.T.); -#23944=ORIENTED_EDGE('',*,*,#23943,.T.); -#23946=ORIENTED_EDGE('',*,*,#23945,.F.); -#23947=EDGE_LOOP('',(#23933,#23935,#23936,#23938,#23940,#23942,#23944,#23946)); -#23948=FACE_OUTER_BOUND('',#23947,.F.); -#23950=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#23951=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23952=DIRECTION('',(0.E0,0.E0,1.E0)); -#23953=AXIS2_PLACEMENT_3D('',#23950,#23951,#23952); -#23954=PLANE('',#23953); -#23956=ORIENTED_EDGE('',*,*,#23955,.T.); -#23958=ORIENTED_EDGE('',*,*,#23957,.F.); -#23959=ORIENTED_EDGE('',*,*,#22145,.F.); -#23961=ORIENTED_EDGE('',*,*,#23960,.T.); -#23963=ORIENTED_EDGE('',*,*,#23962,.T.); -#23965=ORIENTED_EDGE('',*,*,#23964,.T.); -#23967=ORIENTED_EDGE('',*,*,#23966,.T.); -#23969=ORIENTED_EDGE('',*,*,#23968,.F.); -#23970=EDGE_LOOP('',(#23956,#23958,#23959,#23961,#23963,#23965,#23967,#23969)); -#23971=FACE_OUTER_BOUND('',#23970,.F.); -#23973=CARTESIAN_POINT('',(-7.5E0,-3.E-1,-1.43E1)); -#23974=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23975=DIRECTION('',(0.E0,0.E0,1.E0)); -#23976=AXIS2_PLACEMENT_3D('',#23973,#23974,#23975); -#23977=PLANE('',#23976); -#23979=ORIENTED_EDGE('',*,*,#23978,.T.); -#23980=ORIENTED_EDGE('',*,*,#23900,.F.); -#23981=ORIENTED_EDGE('',*,*,#22301,.F.); -#23983=ORIENTED_EDGE('',*,*,#23982,.T.); -#23985=ORIENTED_EDGE('',*,*,#23984,.T.); -#23987=ORIENTED_EDGE('',*,*,#23986,.F.); -#23988=EDGE_LOOP('',(#23979,#23980,#23981,#23983,#23985,#23987)); -#23989=FACE_OUTER_BOUND('',#23988,.F.); -#23991=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#23992=DIRECTION('',(0.E0,-1.E0,0.E0)); -#23993=DIRECTION('',(-1.E0,0.E0,0.E0)); -#23994=AXIS2_PLACEMENT_3D('',#23991,#23992,#23993); -#23995=PLANE('',#23994); -#23996=ORIENTED_EDGE('',*,*,#23913,.F.); -#23998=ORIENTED_EDGE('',*,*,#23997,.F.); -#24000=ORIENTED_EDGE('',*,*,#23999,.F.); -#24002=ORIENTED_EDGE('',*,*,#24001,.F.); -#24003=ORIENTED_EDGE('',*,*,#23932,.F.); -#24005=ORIENTED_EDGE('',*,*,#24004,.F.); -#24006=EDGE_LOOP('',(#23996,#23998,#24000,#24002,#24003,#24005)); -#24007=FACE_OUTER_BOUND('',#24006,.F.); -#24009=FILL_AREA_STYLE_COLOUR('',#15); -#24010=FILL_AREA_STYLE('',(#24009)); -#24011=SURFACE_STYLE_FILL_AREA(#24010); -#24012=SURFACE_SIDE_STYLE('',(#24011)); -#24013=SURFACE_STYLE_USAGE(.POSITIVE.,#24012); -#24014=PRESENTATION_STYLE_ASSIGNMENT((#24013)); -#24015=STYLED_ITEM('',(#24014),#24008); -#24016=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#24017=DIRECTION('',(0.E0,-1.E0,0.E0)); -#24018=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24019=AXIS2_PLACEMENT_3D('',#24016,#24017,#24018); -#24020=PLANE('',#24019); -#24021=ORIENTED_EDGE('',*,*,#23939,.F.); -#24023=ORIENTED_EDGE('',*,*,#24022,.F.); -#24025=ORIENTED_EDGE('',*,*,#24024,.F.); -#24027=ORIENTED_EDGE('',*,*,#24026,.F.); -#24028=ORIENTED_EDGE('',*,*,#23955,.F.); -#24030=ORIENTED_EDGE('',*,*,#24029,.F.); -#24031=EDGE_LOOP('',(#24021,#24023,#24025,#24027,#24028,#24030)); -#24032=FACE_OUTER_BOUND('',#24031,.F.); -#24034=FILL_AREA_STYLE_COLOUR('',#15); -#24035=FILL_AREA_STYLE('',(#24034)); -#24036=SURFACE_STYLE_FILL_AREA(#24035); -#24037=SURFACE_SIDE_STYLE('',(#24036)); -#24038=SURFACE_STYLE_USAGE(.POSITIVE.,#24037); -#24039=PRESENTATION_STYLE_ASSIGNMENT((#24038)); -#24040=STYLED_ITEM('',(#24039),#24033); -#24041=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#24042=DIRECTION('',(0.E0,-1.E0,0.E0)); -#24043=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24044=AXIS2_PLACEMENT_3D('',#24041,#24042,#24043); -#24045=PLANE('',#24044); -#24046=ORIENTED_EDGE('',*,*,#23962,.F.); -#24048=ORIENTED_EDGE('',*,*,#24047,.F.); -#24049=ORIENTED_EDGE('',*,*,#23887,.F.); -#24050=ORIENTED_EDGE('',*,*,#23902,.F.); -#24051=ORIENTED_EDGE('',*,*,#23978,.F.); -#24053=ORIENTED_EDGE('',*,*,#24052,.F.); -#24054=EDGE_LOOP('',(#24046,#24048,#24049,#24050,#24051,#24053)); -#24055=FACE_OUTER_BOUND('',#24054,.F.); -#24057=FILL_AREA_STYLE_COLOUR('',#15); -#24058=FILL_AREA_STYLE('',(#24057)); -#24059=SURFACE_STYLE_FILL_AREA(#24058); -#24060=SURFACE_SIDE_STYLE('',(#24059)); -#24061=SURFACE_STYLE_USAGE(.POSITIVE.,#24060); -#24062=PRESENTATION_STYLE_ASSIGNMENT((#24061)); -#24063=STYLED_ITEM('',(#24062),#24056); -#24064=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1235E1)); -#24065=DIRECTION('',(0.E0,0.E0,1.E0)); -#24066=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24067=AXIS2_PLACEMENT_3D('',#24064,#24065,#24066); -#24068=PLANE('',#24067); -#24069=ORIENTED_EDGE('',*,*,#22159,.T.); -#24071=ORIENTED_EDGE('',*,*,#24070,.T.); -#24072=ORIENTED_EDGE('',*,*,#23997,.T.); -#24073=ORIENTED_EDGE('',*,*,#23922,.F.); -#24074=EDGE_LOOP('',(#24069,#24071,#24072,#24073)); -#24075=FACE_OUTER_BOUND('',#24074,.F.); -#24077=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.1835E1)); -#24078=DIRECTION('',(1.E0,0.E0,0.E0)); -#24079=DIRECTION('',(0.E0,0.E0,1.E0)); -#24080=AXIS2_PLACEMENT_3D('',#24077,#24078,#24079); -#24081=PLANE('',#24080); -#24082=ORIENTED_EDGE('',*,*,#22157,.F.); -#24084=ORIENTED_EDGE('',*,*,#24083,.T.); -#24085=ORIENTED_EDGE('',*,*,#23999,.T.); -#24086=ORIENTED_EDGE('',*,*,#24070,.F.); -#24087=EDGE_LOOP('',(#24082,#24084,#24085,#24086)); -#24088=FACE_OUTER_BOUND('',#24087,.F.); -#24090=CARTESIAN_POINT('',(-7.640579250739E0,-3.E-1,-1.1835E1)); -#24091=DIRECTION('',(0.E0,0.E0,-1.E0)); -#24092=DIRECTION('',(1.E0,0.E0,0.E0)); -#24093=AXIS2_PLACEMENT_3D('',#24090,#24091,#24092); -#24094=PLANE('',#24093); -#24095=ORIENTED_EDGE('',*,*,#22155,.F.); -#24096=ORIENTED_EDGE('',*,*,#23934,.T.); -#24097=ORIENTED_EDGE('',*,*,#24001,.T.); -#24098=ORIENTED_EDGE('',*,*,#24083,.F.); -#24099=EDGE_LOOP('',(#24095,#24096,#24097,#24098)); -#24100=FACE_OUTER_BOUND('',#24099,.F.); -#24102=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.1535E1)); -#24103=DIRECTION('',(0.E0,1.E0,0.E0)); -#24104=DIRECTION('',(1.E0,0.E0,0.E0)); -#24105=AXIS2_PLACEMENT_3D('',#24102,#24103,#24104); -#24106=CYLINDRICAL_SURFACE('',#24105,2.5E-1); -#24107=ORIENTED_EDGE('',*,*,#24004,.T.); -#24108=ORIENTED_EDGE('',*,*,#23945,.T.); -#24110=ORIENTED_EDGE('',*,*,#24109,.T.); -#24111=ORIENTED_EDGE('',*,*,#23915,.F.); -#24112=EDGE_LOOP('',(#24107,#24108,#24110,#24111)); -#24113=FACE_OUTER_BOUND('',#24112,.F.); -#24115=FILL_AREA_STYLE_COLOUR('',#15); -#24116=FILL_AREA_STYLE('',(#24115)); -#24117=SURFACE_STYLE_FILL_AREA(#24116); -#24118=SURFACE_SIDE_STYLE('',(#24117)); -#24119=SURFACE_STYLE_USAGE(.NEGATIVE.,#24118); -#24120=PRESENTATION_STYLE_ASSIGNMENT((#24119)); -#24121=STYLED_ITEM('',(#24120),#24114); -#24122=CARTESIAN_POINT('',(0.E0,3.E-1,0.E0)); -#24123=DIRECTION('',(0.E0,1.E0,0.E0)); -#24124=DIRECTION('',(1.E0,0.E0,0.E0)); -#24125=AXIS2_PLACEMENT_3D('',#24122,#24123,#24124); -#24126=PLANE('',#24125); -#24128=ORIENTED_EDGE('',*,*,#24127,.F.); -#24129=ORIENTED_EDGE('',*,*,#23984,.F.); -#24131=ORIENTED_EDGE('',*,*,#24130,.F.); -#24133=ORIENTED_EDGE('',*,*,#24132,.F.); -#24135=ORIENTED_EDGE('',*,*,#24134,.T.); -#24137=ORIENTED_EDGE('',*,*,#24136,.T.); -#24139=ORIENTED_EDGE('',*,*,#24138,.F.); -#24141=ORIENTED_EDGE('',*,*,#24140,.F.); -#24143=ORIENTED_EDGE('',*,*,#24142,.T.); -#24145=ORIENTED_EDGE('',*,*,#24144,.T.); -#24147=ORIENTED_EDGE('',*,*,#24146,.F.); -#24149=ORIENTED_EDGE('',*,*,#24148,.F.); -#24151=ORIENTED_EDGE('',*,*,#24150,.T.); -#24153=ORIENTED_EDGE('',*,*,#24152,.T.); -#24155=ORIENTED_EDGE('',*,*,#24154,.F.); -#24157=ORIENTED_EDGE('',*,*,#24156,.F.); -#24159=ORIENTED_EDGE('',*,*,#24158,.T.); -#24161=ORIENTED_EDGE('',*,*,#24160,.T.); -#24163=ORIENTED_EDGE('',*,*,#24162,.F.); -#24165=ORIENTED_EDGE('',*,*,#24164,.F.); -#24167=ORIENTED_EDGE('',*,*,#24166,.T.); -#24169=ORIENTED_EDGE('',*,*,#24168,.T.); -#24171=ORIENTED_EDGE('',*,*,#24170,.F.); -#24173=ORIENTED_EDGE('',*,*,#24172,.F.); -#24175=ORIENTED_EDGE('',*,*,#24174,.T.); -#24177=ORIENTED_EDGE('',*,*,#24176,.T.); -#24179=ORIENTED_EDGE('',*,*,#24178,.F.); -#24181=ORIENTED_EDGE('',*,*,#24180,.F.); -#24183=ORIENTED_EDGE('',*,*,#24182,.T.); -#24185=ORIENTED_EDGE('',*,*,#24184,.T.); -#24187=ORIENTED_EDGE('',*,*,#24186,.F.); -#24189=ORIENTED_EDGE('',*,*,#24188,.F.); -#24191=ORIENTED_EDGE('',*,*,#24190,.T.); -#24193=ORIENTED_EDGE('',*,*,#24192,.T.); -#24195=ORIENTED_EDGE('',*,*,#24194,.F.); -#24197=ORIENTED_EDGE('',*,*,#24196,.F.); -#24199=ORIENTED_EDGE('',*,*,#24198,.F.); -#24201=ORIENTED_EDGE('',*,*,#24200,.F.); -#24203=ORIENTED_EDGE('',*,*,#24202,.T.); -#24205=ORIENTED_EDGE('',*,*,#24204,.T.); -#24207=ORIENTED_EDGE('',*,*,#24206,.T.); -#24209=ORIENTED_EDGE('',*,*,#24208,.F.); -#24211=ORIENTED_EDGE('',*,*,#24210,.T.); -#24213=ORIENTED_EDGE('',*,*,#24212,.T.); -#24215=ORIENTED_EDGE('',*,*,#24214,.T.); -#24217=ORIENTED_EDGE('',*,*,#24216,.F.); -#24219=ORIENTED_EDGE('',*,*,#24218,.T.); -#24221=ORIENTED_EDGE('',*,*,#24220,.T.); -#24223=ORIENTED_EDGE('',*,*,#24222,.T.); -#24225=ORIENTED_EDGE('',*,*,#24224,.F.); -#24227=ORIENTED_EDGE('',*,*,#24226,.T.); -#24229=ORIENTED_EDGE('',*,*,#24228,.T.); -#24231=ORIENTED_EDGE('',*,*,#24230,.T.); -#24233=ORIENTED_EDGE('',*,*,#24232,.F.); -#24235=ORIENTED_EDGE('',*,*,#24234,.T.); -#24237=ORIENTED_EDGE('',*,*,#24236,.T.); -#24239=ORIENTED_EDGE('',*,*,#24238,.T.); -#24241=ORIENTED_EDGE('',*,*,#24240,.F.); -#24243=ORIENTED_EDGE('',*,*,#24242,.T.); -#24245=ORIENTED_EDGE('',*,*,#24244,.T.); -#24247=ORIENTED_EDGE('',*,*,#24246,.T.); -#24249=ORIENTED_EDGE('',*,*,#24248,.F.); -#24251=ORIENTED_EDGE('',*,*,#24250,.T.); -#24253=ORIENTED_EDGE('',*,*,#24252,.T.); -#24255=ORIENTED_EDGE('',*,*,#24254,.T.); -#24257=ORIENTED_EDGE('',*,*,#24256,.F.); -#24259=ORIENTED_EDGE('',*,*,#24258,.T.); -#24261=ORIENTED_EDGE('',*,*,#24260,.T.); -#24263=ORIENTED_EDGE('',*,*,#24262,.T.); -#24265=ORIENTED_EDGE('',*,*,#24264,.F.); -#24267=ORIENTED_EDGE('',*,*,#24266,.F.); -#24268=ORIENTED_EDGE('',*,*,#23917,.F.); -#24269=ORIENTED_EDGE('',*,*,#24109,.F.); -#24270=ORIENTED_EDGE('',*,*,#23943,.F.); -#24272=ORIENTED_EDGE('',*,*,#24271,.F.); -#24273=ORIENTED_EDGE('',*,*,#23966,.F.); -#24274=EDGE_LOOP('',(#24128,#24129,#24131,#24133,#24135,#24137,#24139,#24141, -#24143,#24145,#24147,#24149,#24151,#24153,#24155,#24157,#24159,#24161,#24163, -#24165,#24167,#24169,#24171,#24173,#24175,#24177,#24179,#24181,#24183,#24185, -#24187,#24189,#24191,#24193,#24195,#24197,#24199,#24201,#24203,#24205,#24207, -#24209,#24211,#24213,#24215,#24217,#24219,#24221,#24223,#24225,#24227,#24229, -#24231,#24233,#24235,#24237,#24239,#24241,#24243,#24245,#24247,#24249,#24251, -#24253,#24255,#24257,#24259,#24261,#24263,#24265,#24267,#24268,#24269,#24270, -#24272,#24273)); -#24275=FACE_OUTER_BOUND('',#24274,.F.); -#24277=ORIENTED_EDGE('',*,*,#24276,.T.); -#24279=ORIENTED_EDGE('',*,*,#24278,.F.); -#24281=ORIENTED_EDGE('',*,*,#24280,.F.); -#24283=ORIENTED_EDGE('',*,*,#24282,.F.); -#24284=EDGE_LOOP('',(#24277,#24279,#24281,#24283)); -#24285=FACE_BOUND('',#24284,.F.); -#24287=ORIENTED_EDGE('',*,*,#24286,.T.); -#24289=ORIENTED_EDGE('',*,*,#24288,.F.); -#24291=ORIENTED_EDGE('',*,*,#24290,.F.); -#24293=ORIENTED_EDGE('',*,*,#24292,.F.); -#24294=EDGE_LOOP('',(#24287,#24289,#24291,#24293)); -#24295=FACE_BOUND('',#24294,.F.); -#24297=ORIENTED_EDGE('',*,*,#24296,.T.); -#24299=ORIENTED_EDGE('',*,*,#24298,.F.); -#24301=ORIENTED_EDGE('',*,*,#24300,.F.); -#24303=ORIENTED_EDGE('',*,*,#24302,.F.); -#24304=EDGE_LOOP('',(#24297,#24299,#24301,#24303)); -#24305=FACE_BOUND('',#24304,.F.); -#24307=ORIENTED_EDGE('',*,*,#24306,.T.); -#24309=ORIENTED_EDGE('',*,*,#24308,.F.); -#24311=ORIENTED_EDGE('',*,*,#24310,.F.); -#24313=ORIENTED_EDGE('',*,*,#24312,.F.); -#24315=ORIENTED_EDGE('',*,*,#24314,.F.); -#24317=ORIENTED_EDGE('',*,*,#24316,.T.); -#24318=EDGE_LOOP('',(#24307,#24309,#24311,#24313,#24315,#24317)); -#24319=FACE_BOUND('',#24318,.F.); -#24321=ORIENTED_EDGE('',*,*,#24320,.T.); -#24323=ORIENTED_EDGE('',*,*,#24322,.F.); -#24325=ORIENTED_EDGE('',*,*,#24324,.F.); -#24327=ORIENTED_EDGE('',*,*,#24326,.F.); -#24328=EDGE_LOOP('',(#24321,#24323,#24325,#24327)); -#24329=FACE_BOUND('',#24328,.F.); -#24331=ORIENTED_EDGE('',*,*,#24330,.T.); -#24333=ORIENTED_EDGE('',*,*,#24332,.F.); -#24335=ORIENTED_EDGE('',*,*,#24334,.F.); -#24337=ORIENTED_EDGE('',*,*,#24336,.F.); -#24339=ORIENTED_EDGE('',*,*,#24338,.F.); -#24341=ORIENTED_EDGE('',*,*,#24340,.T.); -#24342=EDGE_LOOP('',(#24331,#24333,#24335,#24337,#24339,#24341)); -#24343=FACE_BOUND('',#24342,.F.); -#24345=ORIENTED_EDGE('',*,*,#24344,.T.); -#24347=ORIENTED_EDGE('',*,*,#24346,.F.); -#24349=ORIENTED_EDGE('',*,*,#24348,.F.); -#24351=ORIENTED_EDGE('',*,*,#24350,.F.); -#24353=ORIENTED_EDGE('',*,*,#24352,.F.); -#24355=ORIENTED_EDGE('',*,*,#24354,.T.); -#24356=EDGE_LOOP('',(#24345,#24347,#24349,#24351,#24353,#24355)); -#24357=FACE_BOUND('',#24356,.F.); -#24359=FILL_AREA_STYLE_COLOUR('',#3); -#24360=FILL_AREA_STYLE('',(#24359)); -#24361=SURFACE_STYLE_FILL_AREA(#24360); -#24362=SURFACE_SIDE_STYLE('',(#24361)); -#24363=SURFACE_STYLE_USAGE(.POSITIVE.,#24362); -#24364=PRESENTATION_STYLE_ASSIGNMENT((#24363)); -#24365=STYLED_ITEM('',(#24364),#24358); -#24366=CARTESIAN_POINT('',(6.8E0,3.E-1,1.342E1)); -#24367=DIRECTION('',(1.E0,0.E0,0.E0)); -#24368=DIRECTION('',(0.E0,0.E0,-1.E0)); -#24369=AXIS2_PLACEMENT_3D('',#24366,#24367,#24368); -#24370=PLANE('',#24369); -#24372=ORIENTED_EDGE('',*,*,#24371,.F.); -#24374=ORIENTED_EDGE('',*,*,#24373,.F.); -#24375=ORIENTED_EDGE('',*,*,#24344,.F.); -#24377=ORIENTED_EDGE('',*,*,#24376,.T.); -#24379=ORIENTED_EDGE('',*,*,#24378,.F.); -#24381=ORIENTED_EDGE('',*,*,#24380,.F.); -#24383=ORIENTED_EDGE('',*,*,#24382,.F.); -#24385=ORIENTED_EDGE('',*,*,#24384,.F.); -#24386=ORIENTED_EDGE('',*,*,#24286,.F.); -#24388=ORIENTED_EDGE('',*,*,#24387,.T.); -#24390=ORIENTED_EDGE('',*,*,#24389,.F.); -#24392=ORIENTED_EDGE('',*,*,#24391,.F.); -#24393=ORIENTED_EDGE('',*,*,#24276,.F.); -#24395=ORIENTED_EDGE('',*,*,#24394,.T.); -#24396=EDGE_LOOP('',(#24372,#24374,#24375,#24377,#24379,#24381,#24383,#24385, -#24386,#24388,#24390,#24392,#24393,#24395)); -#24397=FACE_OUTER_BOUND('',#24396,.F.); -#24399=CARTESIAN_POINT('',(0.E0,1.4E0,0.E0)); -#24400=DIRECTION('',(0.E0,1.E0,0.E0)); -#24401=DIRECTION('',(1.E0,0.E0,0.E0)); -#24402=AXIS2_PLACEMENT_3D('',#24399,#24400,#24401); -#24403=PLANE('',#24402); -#24405=ORIENTED_EDGE('',*,*,#24404,.T.); -#24407=ORIENTED_EDGE('',*,*,#24406,.T.); -#24409=ORIENTED_EDGE('',*,*,#24408,.T.); -#24411=ORIENTED_EDGE('',*,*,#24410,.T.); -#24413=ORIENTED_EDGE('',*,*,#24412,.T.); -#24415=ORIENTED_EDGE('',*,*,#24414,.T.); -#24417=ORIENTED_EDGE('',*,*,#24416,.T.); -#24419=ORIENTED_EDGE('',*,*,#24418,.T.); -#24421=ORIENTED_EDGE('',*,*,#24420,.T.); -#24423=ORIENTED_EDGE('',*,*,#24422,.T.); -#24425=ORIENTED_EDGE('',*,*,#24424,.T.); -#24427=ORIENTED_EDGE('',*,*,#24426,.T.); -#24429=ORIENTED_EDGE('',*,*,#24428,.T.); -#24431=ORIENTED_EDGE('',*,*,#24430,.T.); -#24432=ORIENTED_EDGE('',*,*,#24371,.T.); -#24434=ORIENTED_EDGE('',*,*,#24433,.T.); -#24436=ORIENTED_EDGE('',*,*,#24435,.T.); -#24438=ORIENTED_EDGE('',*,*,#24437,.T.); -#24439=ORIENTED_EDGE('',*,*,#24389,.T.); -#24441=ORIENTED_EDGE('',*,*,#24440,.T.); -#24443=ORIENTED_EDGE('',*,*,#24442,.T.); -#24445=ORIENTED_EDGE('',*,*,#24444,.T.); -#24446=ORIENTED_EDGE('',*,*,#24382,.T.); -#24448=ORIENTED_EDGE('',*,*,#24447,.T.); -#24450=ORIENTED_EDGE('',*,*,#24449,.T.); -#24452=ORIENTED_EDGE('',*,*,#24451,.T.); -#24454=ORIENTED_EDGE('',*,*,#24453,.T.); -#24456=ORIENTED_EDGE('',*,*,#24455,.T.); -#24458=ORIENTED_EDGE('',*,*,#24457,.T.); -#24460=ORIENTED_EDGE('',*,*,#24459,.T.); -#24462=ORIENTED_EDGE('',*,*,#24461,.T.); -#24464=ORIENTED_EDGE('',*,*,#24463,.T.); -#24465=EDGE_LOOP('',(#24405,#24407,#24409,#24411,#24413,#24415,#24417,#24419, -#24421,#24423,#24425,#24427,#24429,#24431,#24432,#24434,#24436,#24438,#24439, -#24441,#24443,#24445,#24446,#24448,#24450,#24452,#24454,#24456,#24458,#24460, -#24462,#24464)); -#24466=FACE_OUTER_BOUND('',#24465,.F.); -#24468=CARTESIAN_POINT('',(-5.4E0,3.E-1,-3.98E0)); -#24469=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24470=DIRECTION('',(0.E0,0.E0,1.E0)); -#24471=AXIS2_PLACEMENT_3D('',#24468,#24469,#24470); -#24472=PLANE('',#24471); -#24473=ORIENTED_EDGE('',*,*,#24404,.F.); -#24475=ORIENTED_EDGE('',*,*,#24474,.F.); -#24476=ORIENTED_EDGE('',*,*,#24306,.F.); -#24478=ORIENTED_EDGE('',*,*,#24477,.T.); -#24480=ORIENTED_EDGE('',*,*,#24479,.F.); -#24482=ORIENTED_EDGE('',*,*,#24481,.F.); -#24483=ORIENTED_EDGE('',*,*,#24340,.F.); -#24485=ORIENTED_EDGE('',*,*,#24484,.T.); -#24486=ORIENTED_EDGE('',*,*,#24412,.F.); -#24488=ORIENTED_EDGE('',*,*,#24487,.F.); -#24489=ORIENTED_EDGE('',*,*,#24320,.F.); -#24491=ORIENTED_EDGE('',*,*,#24490,.T.); -#24492=EDGE_LOOP('',(#24473,#24475,#24476,#24478,#24480,#24482,#24483,#24485, -#24486,#24488,#24489,#24491)); -#24493=FACE_OUTER_BOUND('',#24492,.F.); -#24495=CARTESIAN_POINT('',(-5.25E0,3.E-1,-7.266321657252E-1)); -#24496=DIRECTION('',(0.E0,0.E0,-1.E0)); -#24497=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24498=AXIS2_PLACEMENT_3D('',#24495,#24496,#24497); -#24499=PLANE('',#24498); -#24500=ORIENTED_EDGE('',*,*,#24474,.T.); -#24501=ORIENTED_EDGE('',*,*,#24463,.F.); -#24503=ORIENTED_EDGE('',*,*,#24502,.F.); -#24504=ORIENTED_EDGE('',*,*,#24308,.T.); -#24505=EDGE_LOOP('',(#24500,#24501,#24503,#24504)); -#24506=FACE_OUTER_BOUND('',#24505,.F.); -#24508=CARTESIAN_POINT('',(-5.25E0,3.E-1,-3.83E0)); -#24509=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24510=DIRECTION('',(0.E0,0.E0,1.E0)); -#24511=AXIS2_PLACEMENT_3D('',#24508,#24509,#24510); -#24512=PLANE('',#24511); -#24513=ORIENTED_EDGE('',*,*,#24310,.T.); -#24514=ORIENTED_EDGE('',*,*,#24502,.T.); -#24515=ORIENTED_EDGE('',*,*,#24461,.F.); -#24517=ORIENTED_EDGE('',*,*,#24516,.F.); -#24518=EDGE_LOOP('',(#24513,#24514,#24515,#24517)); -#24519=FACE_OUTER_BOUND('',#24518,.F.); -#24521=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.83E0)); -#24522=DIRECTION('',(0.E0,0.E0,-1.E0)); -#24523=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24524=AXIS2_PLACEMENT_3D('',#24521,#24522,#24523); -#24525=PLANE('',#24524); -#24526=ORIENTED_EDGE('',*,*,#24312,.T.); -#24527=ORIENTED_EDGE('',*,*,#24516,.T.); -#24528=ORIENTED_EDGE('',*,*,#24459,.F.); -#24530=ORIENTED_EDGE('',*,*,#24529,.F.); -#24531=EDGE_LOOP('',(#24526,#24527,#24528,#24530)); -#24532=FACE_OUTER_BOUND('',#24531,.F.); -#24534=CARTESIAN_POINT('',(-5.E-2,3.E-1,-3.98E0)); -#24535=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24536=DIRECTION('',(0.E0,0.E0,1.E0)); -#24537=AXIS2_PLACEMENT_3D('',#24534,#24535,#24536); -#24538=PLANE('',#24537); -#24540=ORIENTED_EDGE('',*,*,#24539,.F.); -#24541=ORIENTED_EDGE('',*,*,#24314,.T.); -#24542=ORIENTED_EDGE('',*,*,#24529,.T.); -#24543=ORIENTED_EDGE('',*,*,#24457,.F.); -#24544=EDGE_LOOP('',(#24540,#24541,#24542,#24543)); -#24545=FACE_OUTER_BOUND('',#24544,.F.); -#24547=CARTESIAN_POINT('',(6.8E0,3.E-1,-3.98E0)); -#24548=DIRECTION('',(0.E0,0.E0,-1.E0)); -#24549=DIRECTION('',(-1.E0,0.E0,0.E0)); -#24550=AXIS2_PLACEMENT_3D('',#24547,#24548,#24549); -#24551=PLANE('',#24550); -#24552=ORIENTED_EDGE('',*,*,#24447,.F.); -#24553=ORIENTED_EDGE('',*,*,#24380,.T.); -#24555=ORIENTED_EDGE('',*,*,#24554,.F.); -#24556=ORIENTED_EDGE('',*,*,#24477,.F.); -#24557=ORIENTED_EDGE('',*,*,#24316,.F.); -#24558=ORIENTED_EDGE('',*,*,#24539,.T.); -#24559=ORIENTED_EDGE('',*,*,#24455,.F.); -#24561=ORIENTED_EDGE('',*,*,#24560,.F.); -#24562=ORIENTED_EDGE('',*,*,#24296,.F.); -#24564=ORIENTED_EDGE('',*,*,#24563,.T.); -#24565=EDGE_LOOP('',(#24552,#24553,#24555,#24556,#24557,#24558,#24559,#24561, -#24562,#24564)); -#24566=FACE_OUTER_BOUND('',#24565,.F.); -#24568=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#24569=DIRECTION('',(0.E0,1.E0,0.E0)); -#24570=DIRECTION('',(1.E0,0.E0,0.E0)); -#24571=AXIS2_PLACEMENT_3D('',#24568,#24569,#24570); -#24572=PLANE('',#24571); -#24573=ORIENTED_EDGE('',*,*,#24479,.T.); -#24574=ORIENTED_EDGE('',*,*,#24554,.T.); -#24575=ORIENTED_EDGE('',*,*,#24378,.T.); -#24577=ORIENTED_EDGE('',*,*,#24576,.T.); -#24578=EDGE_LOOP('',(#24573,#24574,#24575,#24577)); -#24579=FACE_OUTER_BOUND('',#24578,.F.); -#24581=ORIENTED_EDGE('',*,*,#24580,.T.); -#24583=ORIENTED_EDGE('',*,*,#24582,.T.); -#24585=ORIENTED_EDGE('',*,*,#24584,.T.); -#24587=ORIENTED_EDGE('',*,*,#24586,.T.); -#24589=ORIENTED_EDGE('',*,*,#24588,.T.); -#24591=ORIENTED_EDGE('',*,*,#24590,.T.); -#24593=ORIENTED_EDGE('',*,*,#24592,.T.); -#24595=ORIENTED_EDGE('',*,*,#24594,.T.); -#24597=ORIENTED_EDGE('',*,*,#24596,.T.); -#24599=ORIENTED_EDGE('',*,*,#24598,.T.); -#24601=ORIENTED_EDGE('',*,*,#24600,.T.); -#24603=ORIENTED_EDGE('',*,*,#24602,.T.); -#24605=ORIENTED_EDGE('',*,*,#24604,.T.); -#24607=ORIENTED_EDGE('',*,*,#24606,.T.); -#24609=ORIENTED_EDGE('',*,*,#24608,.T.); -#24611=ORIENTED_EDGE('',*,*,#24610,.T.); -#24613=ORIENTED_EDGE('',*,*,#24612,.T.); -#24615=ORIENTED_EDGE('',*,*,#24614,.T.); -#24617=ORIENTED_EDGE('',*,*,#24616,.T.); -#24618=EDGE_LOOP('',(#24581,#24583,#24585,#24587,#24589,#24591,#24593,#24595, -#24597,#24599,#24601,#24603,#24605,#24607,#24609,#24611,#24613,#24615,#24617)); -#24619=FACE_BOUND('',#24618,.F.); -#24621=ORIENTED_EDGE('',*,*,#24620,.T.); -#24623=ORIENTED_EDGE('',*,*,#24622,.T.); -#24625=ORIENTED_EDGE('',*,*,#24624,.T.); -#24627=ORIENTED_EDGE('',*,*,#24626,.T.); -#24629=ORIENTED_EDGE('',*,*,#24628,.T.); -#24631=ORIENTED_EDGE('',*,*,#24630,.T.); -#24633=ORIENTED_EDGE('',*,*,#24632,.T.); -#24635=ORIENTED_EDGE('',*,*,#24634,.T.); -#24636=EDGE_LOOP('',(#24621,#24623,#24625,#24627,#24629,#24631,#24633,#24635)); -#24637=FACE_BOUND('',#24636,.F.); -#24639=ORIENTED_EDGE('',*,*,#24638,.T.); -#24641=ORIENTED_EDGE('',*,*,#24640,.T.); -#24643=ORIENTED_EDGE('',*,*,#24642,.T.); -#24645=ORIENTED_EDGE('',*,*,#24644,.T.); -#24647=ORIENTED_EDGE('',*,*,#24646,.T.); -#24649=ORIENTED_EDGE('',*,*,#24648,.T.); -#24651=ORIENTED_EDGE('',*,*,#24650,.T.); -#24653=ORIENTED_EDGE('',*,*,#24652,.T.); -#24655=ORIENTED_EDGE('',*,*,#24654,.T.); -#24657=ORIENTED_EDGE('',*,*,#24656,.T.); -#24659=ORIENTED_EDGE('',*,*,#24658,.T.); -#24661=ORIENTED_EDGE('',*,*,#24660,.T.); -#24663=ORIENTED_EDGE('',*,*,#24662,.T.); -#24665=ORIENTED_EDGE('',*,*,#24664,.T.); -#24667=ORIENTED_EDGE('',*,*,#24666,.T.); -#24669=ORIENTED_EDGE('',*,*,#24668,.T.); -#24671=ORIENTED_EDGE('',*,*,#24670,.T.); -#24673=ORIENTED_EDGE('',*,*,#24672,.T.); -#24675=ORIENTED_EDGE('',*,*,#24674,.T.); -#24677=ORIENTED_EDGE('',*,*,#24676,.T.); -#24679=ORIENTED_EDGE('',*,*,#24678,.T.); -#24681=ORIENTED_EDGE('',*,*,#24680,.T.); -#24683=ORIENTED_EDGE('',*,*,#24682,.T.); -#24685=ORIENTED_EDGE('',*,*,#24684,.T.); -#24687=ORIENTED_EDGE('',*,*,#24686,.T.); -#24689=ORIENTED_EDGE('',*,*,#24688,.T.); -#24691=ORIENTED_EDGE('',*,*,#24690,.T.); -#24693=ORIENTED_EDGE('',*,*,#24692,.T.); -#24695=ORIENTED_EDGE('',*,*,#24694,.T.); -#24697=ORIENTED_EDGE('',*,*,#24696,.T.); -#24699=ORIENTED_EDGE('',*,*,#24698,.T.); -#24701=ORIENTED_EDGE('',*,*,#24700,.T.); -#24703=ORIENTED_EDGE('',*,*,#24702,.T.); -#24705=ORIENTED_EDGE('',*,*,#24704,.T.); -#24706=EDGE_LOOP('',(#24639,#24641,#24643,#24645,#24647,#24649,#24651,#24653, -#24655,#24657,#24659,#24661,#24663,#24665,#24667,#24669,#24671,#24673,#24675, -#24677,#24679,#24681,#24683,#24685,#24687,#24689,#24691,#24693,#24695,#24697, -#24699,#24701,#24703,#24705)); -#24707=FACE_BOUND('',#24706,.F.); -#24709=ORIENTED_EDGE('',*,*,#24708,.T.); -#24711=ORIENTED_EDGE('',*,*,#24710,.T.); -#24713=ORIENTED_EDGE('',*,*,#24712,.T.); -#24715=ORIENTED_EDGE('',*,*,#24714,.T.); -#24717=ORIENTED_EDGE('',*,*,#24716,.T.); -#24719=ORIENTED_EDGE('',*,*,#24718,.T.); -#24721=ORIENTED_EDGE('',*,*,#24720,.T.); -#24723=ORIENTED_EDGE('',*,*,#24722,.T.); -#24725=ORIENTED_EDGE('',*,*,#24724,.T.); -#24727=ORIENTED_EDGE('',*,*,#24726,.T.); -#24729=ORIENTED_EDGE('',*,*,#24728,.T.); -#24731=ORIENTED_EDGE('',*,*,#24730,.T.); -#24733=ORIENTED_EDGE('',*,*,#24732,.T.); -#24735=ORIENTED_EDGE('',*,*,#24734,.T.); -#24737=ORIENTED_EDGE('',*,*,#24736,.T.); -#24739=ORIENTED_EDGE('',*,*,#24738,.T.); -#24741=ORIENTED_EDGE('',*,*,#24740,.T.); -#24743=ORIENTED_EDGE('',*,*,#24742,.T.); -#24745=ORIENTED_EDGE('',*,*,#24744,.T.); -#24747=ORIENTED_EDGE('',*,*,#24746,.T.); -#24749=ORIENTED_EDGE('',*,*,#24748,.T.); -#24751=ORIENTED_EDGE('',*,*,#24750,.T.); -#24753=ORIENTED_EDGE('',*,*,#24752,.T.); -#24755=ORIENTED_EDGE('',*,*,#24754,.T.); -#24757=ORIENTED_EDGE('',*,*,#24756,.T.); -#24759=ORIENTED_EDGE('',*,*,#24758,.T.); -#24761=ORIENTED_EDGE('',*,*,#24760,.T.); -#24763=ORIENTED_EDGE('',*,*,#24762,.T.); -#24765=ORIENTED_EDGE('',*,*,#24764,.T.); -#24767=ORIENTED_EDGE('',*,*,#24766,.T.); -#24769=ORIENTED_EDGE('',*,*,#24768,.T.); -#24771=ORIENTED_EDGE('',*,*,#24770,.T.); -#24773=ORIENTED_EDGE('',*,*,#24772,.T.); -#24775=ORIENTED_EDGE('',*,*,#24774,.T.); -#24777=ORIENTED_EDGE('',*,*,#24776,.T.); -#24779=ORIENTED_EDGE('',*,*,#24778,.T.); -#24781=ORIENTED_EDGE('',*,*,#24780,.T.); -#24783=ORIENTED_EDGE('',*,*,#24782,.T.); -#24785=ORIENTED_EDGE('',*,*,#24784,.T.); -#24787=ORIENTED_EDGE('',*,*,#24786,.T.); -#24789=ORIENTED_EDGE('',*,*,#24788,.T.); -#24791=ORIENTED_EDGE('',*,*,#24790,.T.); -#24793=ORIENTED_EDGE('',*,*,#24792,.T.); -#24795=ORIENTED_EDGE('',*,*,#24794,.T.); -#24797=ORIENTED_EDGE('',*,*,#24796,.T.); -#24799=ORIENTED_EDGE('',*,*,#24798,.T.); -#24801=ORIENTED_EDGE('',*,*,#24800,.T.); -#24803=ORIENTED_EDGE('',*,*,#24802,.T.); -#24805=ORIENTED_EDGE('',*,*,#24804,.T.); -#24807=ORIENTED_EDGE('',*,*,#24806,.T.); -#24809=ORIENTED_EDGE('',*,*,#24808,.T.); -#24811=ORIENTED_EDGE('',*,*,#24810,.T.); -#24813=ORIENTED_EDGE('',*,*,#24812,.T.); -#24815=ORIENTED_EDGE('',*,*,#24814,.T.); -#24817=ORIENTED_EDGE('',*,*,#24816,.T.); -#24819=ORIENTED_EDGE('',*,*,#24818,.T.); -#24821=ORIENTED_EDGE('',*,*,#24820,.T.); -#24822=EDGE_LOOP('',(#24709,#24711,#24713,#24715,#24717,#24719,#24721,#24723, -#24725,#24727,#24729,#24731,#24733,#24735,#24737,#24739,#24741,#24743,#24745, -#24747,#24749,#24751,#24753,#24755,#24757,#24759,#24761,#24763,#24765,#24767, -#24769,#24771,#24773,#24775,#24777,#24779,#24781,#24783,#24785,#24787,#24789, -#24791,#24793,#24795,#24797,#24799,#24801,#24803,#24805,#24807,#24809,#24811, -#24813,#24815,#24817,#24819,#24821)); -#24823=FACE_BOUND('',#24822,.F.); -#24825=ORIENTED_EDGE('',*,*,#24824,.T.); -#24827=ORIENTED_EDGE('',*,*,#24826,.T.); -#24829=ORIENTED_EDGE('',*,*,#24828,.T.); -#24831=ORIENTED_EDGE('',*,*,#24830,.T.); -#24833=ORIENTED_EDGE('',*,*,#24832,.T.); -#24835=ORIENTED_EDGE('',*,*,#24834,.T.); -#24837=ORIENTED_EDGE('',*,*,#24836,.T.); -#24839=ORIENTED_EDGE('',*,*,#24838,.T.); -#24841=ORIENTED_EDGE('',*,*,#24840,.T.); -#24843=ORIENTED_EDGE('',*,*,#24842,.T.); -#24845=ORIENTED_EDGE('',*,*,#24844,.T.); -#24847=ORIENTED_EDGE('',*,*,#24846,.T.); -#24849=ORIENTED_EDGE('',*,*,#24848,.T.); -#24851=ORIENTED_EDGE('',*,*,#24850,.T.); -#24853=ORIENTED_EDGE('',*,*,#24852,.T.); -#24855=ORIENTED_EDGE('',*,*,#24854,.T.); -#24857=ORIENTED_EDGE('',*,*,#24856,.T.); -#24859=ORIENTED_EDGE('',*,*,#24858,.T.); -#24861=ORIENTED_EDGE('',*,*,#24860,.T.); -#24863=ORIENTED_EDGE('',*,*,#24862,.T.); -#24865=ORIENTED_EDGE('',*,*,#24864,.T.); -#24867=ORIENTED_EDGE('',*,*,#24866,.T.); -#24869=ORIENTED_EDGE('',*,*,#24868,.T.); -#24871=ORIENTED_EDGE('',*,*,#24870,.T.); -#24873=ORIENTED_EDGE('',*,*,#24872,.T.); -#24875=ORIENTED_EDGE('',*,*,#24874,.T.); -#24877=ORIENTED_EDGE('',*,*,#24876,.T.); -#24879=ORIENTED_EDGE('',*,*,#24878,.T.); -#24880=EDGE_LOOP('',(#24825,#24827,#24829,#24831,#24833,#24835,#24837,#24839, -#24841,#24843,#24845,#24847,#24849,#24851,#24853,#24855,#24857,#24859,#24861, -#24863,#24865,#24867,#24869,#24871,#24873,#24875,#24877,#24879)); -#24881=FACE_BOUND('',#24880,.F.); -#24883=ORIENTED_EDGE('',*,*,#24882,.T.); -#24885=ORIENTED_EDGE('',*,*,#24884,.T.); -#24887=ORIENTED_EDGE('',*,*,#24886,.T.); -#24889=ORIENTED_EDGE('',*,*,#24888,.T.); -#24891=ORIENTED_EDGE('',*,*,#24890,.T.); -#24893=ORIENTED_EDGE('',*,*,#24892,.T.); -#24895=ORIENTED_EDGE('',*,*,#24894,.T.); -#24897=ORIENTED_EDGE('',*,*,#24896,.T.); -#24899=ORIENTED_EDGE('',*,*,#24898,.T.); -#24901=ORIENTED_EDGE('',*,*,#24900,.T.); -#24903=ORIENTED_EDGE('',*,*,#24902,.T.); -#24905=ORIENTED_EDGE('',*,*,#24904,.T.); -#24906=EDGE_LOOP('',(#24883,#24885,#24887,#24889,#24891,#24893,#24895,#24897, -#24899,#24901,#24903,#24905)); -#24907=FACE_BOUND('',#24906,.F.); -#24909=ORIENTED_EDGE('',*,*,#24908,.T.); -#24911=ORIENTED_EDGE('',*,*,#24910,.T.); -#24913=ORIENTED_EDGE('',*,*,#24912,.T.); -#24915=ORIENTED_EDGE('',*,*,#24914,.T.); -#24917=ORIENTED_EDGE('',*,*,#24916,.T.); -#24919=ORIENTED_EDGE('',*,*,#24918,.T.); -#24921=ORIENTED_EDGE('',*,*,#24920,.T.); -#24923=ORIENTED_EDGE('',*,*,#24922,.T.); -#24925=ORIENTED_EDGE('',*,*,#24924,.T.); -#24927=ORIENTED_EDGE('',*,*,#24926,.T.); -#24928=EDGE_LOOP('',(#24909,#24911,#24913,#24915,#24917,#24919,#24921,#24923, -#24925,#24927)); -#24929=FACE_BOUND('',#24928,.F.); -#24931=ORIENTED_EDGE('',*,*,#24930,.T.); -#24933=ORIENTED_EDGE('',*,*,#24932,.T.); -#24935=ORIENTED_EDGE('',*,*,#24934,.T.); -#24937=ORIENTED_EDGE('',*,*,#24936,.T.); -#24939=ORIENTED_EDGE('',*,*,#24938,.T.); -#24941=ORIENTED_EDGE('',*,*,#24940,.T.); -#24943=ORIENTED_EDGE('',*,*,#24942,.T.); -#24945=ORIENTED_EDGE('',*,*,#24944,.T.); -#24947=ORIENTED_EDGE('',*,*,#24946,.T.); -#24949=ORIENTED_EDGE('',*,*,#24948,.T.); -#24951=ORIENTED_EDGE('',*,*,#24950,.T.); -#24953=ORIENTED_EDGE('',*,*,#24952,.T.); -#24955=ORIENTED_EDGE('',*,*,#24954,.T.); -#24957=ORIENTED_EDGE('',*,*,#24956,.T.); -#24959=ORIENTED_EDGE('',*,*,#24958,.T.); -#24961=ORIENTED_EDGE('',*,*,#24960,.T.); -#24963=ORIENTED_EDGE('',*,*,#24962,.T.); -#24965=ORIENTED_EDGE('',*,*,#24964,.T.); -#24967=ORIENTED_EDGE('',*,*,#24966,.T.); -#24969=ORIENTED_EDGE('',*,*,#24968,.T.); -#24971=ORIENTED_EDGE('',*,*,#24970,.T.); -#24973=ORIENTED_EDGE('',*,*,#24972,.T.); -#24975=ORIENTED_EDGE('',*,*,#24974,.T.); -#24977=ORIENTED_EDGE('',*,*,#24976,.T.); -#24979=ORIENTED_EDGE('',*,*,#24978,.T.); -#24981=ORIENTED_EDGE('',*,*,#24980,.T.); -#24983=ORIENTED_EDGE('',*,*,#24982,.T.); -#24985=ORIENTED_EDGE('',*,*,#24984,.T.); -#24987=ORIENTED_EDGE('',*,*,#24986,.T.); -#24989=ORIENTED_EDGE('',*,*,#24988,.T.); -#24991=ORIENTED_EDGE('',*,*,#24990,.T.); -#24993=ORIENTED_EDGE('',*,*,#24992,.T.); -#24995=ORIENTED_EDGE('',*,*,#24994,.T.); -#24997=ORIENTED_EDGE('',*,*,#24996,.T.); -#24999=ORIENTED_EDGE('',*,*,#24998,.T.); -#25001=ORIENTED_EDGE('',*,*,#25000,.T.); -#25003=ORIENTED_EDGE('',*,*,#25002,.T.); -#25005=ORIENTED_EDGE('',*,*,#25004,.T.); -#25007=ORIENTED_EDGE('',*,*,#25006,.T.); -#25009=ORIENTED_EDGE('',*,*,#25008,.T.); -#25010=EDGE_LOOP('',(#24931,#24933,#24935,#24937,#24939,#24941,#24943,#24945, -#24947,#24949,#24951,#24953,#24955,#24957,#24959,#24961,#24963,#24965,#24967, -#24969,#24971,#24973,#24975,#24977,#24979,#24981,#24983,#24985,#24987,#24989, -#24991,#24993,#24995,#24997,#24999,#25001,#25003,#25005,#25007,#25009)); -#25011=FACE_BOUND('',#25010,.F.); -#25013=ORIENTED_EDGE('',*,*,#25012,.T.); -#25015=ORIENTED_EDGE('',*,*,#25014,.T.); -#25017=ORIENTED_EDGE('',*,*,#25016,.T.); -#25019=ORIENTED_EDGE('',*,*,#25018,.T.); -#25021=ORIENTED_EDGE('',*,*,#25020,.T.); -#25023=ORIENTED_EDGE('',*,*,#25022,.T.); -#25025=ORIENTED_EDGE('',*,*,#25024,.T.); -#25027=ORIENTED_EDGE('',*,*,#25026,.T.); -#25029=ORIENTED_EDGE('',*,*,#25028,.T.); -#25031=ORIENTED_EDGE('',*,*,#25030,.T.); -#25033=ORIENTED_EDGE('',*,*,#25032,.T.); -#25035=ORIENTED_EDGE('',*,*,#25034,.T.); -#25037=ORIENTED_EDGE('',*,*,#25036,.T.); -#25039=ORIENTED_EDGE('',*,*,#25038,.T.); -#25041=ORIENTED_EDGE('',*,*,#25040,.T.); -#25043=ORIENTED_EDGE('',*,*,#25042,.T.); -#25045=ORIENTED_EDGE('',*,*,#25044,.T.); -#25047=ORIENTED_EDGE('',*,*,#25046,.T.); -#25049=ORIENTED_EDGE('',*,*,#25048,.T.); -#25051=ORIENTED_EDGE('',*,*,#25050,.T.); -#25053=ORIENTED_EDGE('',*,*,#25052,.T.); -#25055=ORIENTED_EDGE('',*,*,#25054,.T.); -#25057=ORIENTED_EDGE('',*,*,#25056,.T.); -#25059=ORIENTED_EDGE('',*,*,#25058,.T.); -#25061=ORIENTED_EDGE('',*,*,#25060,.T.); -#25063=ORIENTED_EDGE('',*,*,#25062,.T.); -#25065=ORIENTED_EDGE('',*,*,#25064,.T.); -#25067=ORIENTED_EDGE('',*,*,#25066,.T.); -#25069=ORIENTED_EDGE('',*,*,#25068,.T.); -#25071=ORIENTED_EDGE('',*,*,#25070,.T.); -#25073=ORIENTED_EDGE('',*,*,#25072,.T.); -#25075=ORIENTED_EDGE('',*,*,#25074,.T.); -#25077=ORIENTED_EDGE('',*,*,#25076,.T.); -#25079=ORIENTED_EDGE('',*,*,#25078,.T.); -#25081=ORIENTED_EDGE('',*,*,#25080,.T.); -#25083=ORIENTED_EDGE('',*,*,#25082,.T.); -#25085=ORIENTED_EDGE('',*,*,#25084,.T.); -#25087=ORIENTED_EDGE('',*,*,#25086,.T.); -#25089=ORIENTED_EDGE('',*,*,#25088,.T.); -#25091=ORIENTED_EDGE('',*,*,#25090,.T.); -#25092=EDGE_LOOP('',(#25013,#25015,#25017,#25019,#25021,#25023,#25025,#25027, -#25029,#25031,#25033,#25035,#25037,#25039,#25041,#25043,#25045,#25047,#25049, -#25051,#25053,#25055,#25057,#25059,#25061,#25063,#25065,#25067,#25069,#25071, -#25073,#25075,#25077,#25079,#25081,#25083,#25085,#25087,#25089,#25091)); -#25093=FACE_BOUND('',#25092,.F.); -#25095=ORIENTED_EDGE('',*,*,#25094,.T.); -#25097=ORIENTED_EDGE('',*,*,#25096,.T.); -#25099=ORIENTED_EDGE('',*,*,#25098,.T.); -#25101=ORIENTED_EDGE('',*,*,#25100,.T.); -#25102=EDGE_LOOP('',(#25095,#25097,#25099,#25101)); -#25103=FACE_BOUND('',#25102,.F.); -#25105=ORIENTED_EDGE('',*,*,#25104,.T.); -#25107=ORIENTED_EDGE('',*,*,#25106,.T.); -#25109=ORIENTED_EDGE('',*,*,#25108,.T.); -#25111=ORIENTED_EDGE('',*,*,#25110,.T.); -#25113=ORIENTED_EDGE('',*,*,#25112,.T.); -#25115=ORIENTED_EDGE('',*,*,#25114,.T.); -#25117=ORIENTED_EDGE('',*,*,#25116,.T.); -#25119=ORIENTED_EDGE('',*,*,#25118,.T.); -#25121=ORIENTED_EDGE('',*,*,#25120,.T.); -#25123=ORIENTED_EDGE('',*,*,#25122,.T.); -#25125=ORIENTED_EDGE('',*,*,#25124,.T.); -#25127=ORIENTED_EDGE('',*,*,#25126,.T.); -#25129=ORIENTED_EDGE('',*,*,#25128,.T.); -#25131=ORIENTED_EDGE('',*,*,#25130,.T.); -#25132=EDGE_LOOP('',(#25105,#25107,#25109,#25111,#25113,#25115,#25117,#25119, -#25121,#25123,#25125,#25127,#25129,#25131)); -#25133=FACE_BOUND('',#25132,.F.); -#25135=ORIENTED_EDGE('',*,*,#25134,.T.); -#25137=ORIENTED_EDGE('',*,*,#25136,.T.); -#25139=ORIENTED_EDGE('',*,*,#25138,.T.); -#25141=ORIENTED_EDGE('',*,*,#25140,.T.); -#25142=EDGE_LOOP('',(#25135,#25137,#25139,#25141)); -#25143=FACE_BOUND('',#25142,.F.); -#25145=ORIENTED_EDGE('',*,*,#25144,.T.); -#25147=ORIENTED_EDGE('',*,*,#25146,.T.); -#25149=ORIENTED_EDGE('',*,*,#25148,.T.); -#25151=ORIENTED_EDGE('',*,*,#25150,.T.); -#25152=EDGE_LOOP('',(#25145,#25147,#25149,#25151)); -#25153=FACE_BOUND('',#25152,.F.); -#25155=ORIENTED_EDGE('',*,*,#25154,.T.); -#25157=ORIENTED_EDGE('',*,*,#25156,.T.); -#25159=ORIENTED_EDGE('',*,*,#25158,.T.); -#25161=ORIENTED_EDGE('',*,*,#25160,.T.); -#25163=ORIENTED_EDGE('',*,*,#25162,.T.); -#25165=ORIENTED_EDGE('',*,*,#25164,.T.); -#25167=ORIENTED_EDGE('',*,*,#25166,.T.); -#25169=ORIENTED_EDGE('',*,*,#25168,.T.); -#25171=ORIENTED_EDGE('',*,*,#25170,.T.); -#25173=ORIENTED_EDGE('',*,*,#25172,.T.); -#25175=ORIENTED_EDGE('',*,*,#25174,.T.); -#25177=ORIENTED_EDGE('',*,*,#25176,.T.); -#25178=EDGE_LOOP('',(#25155,#25157,#25159,#25161,#25163,#25165,#25167,#25169, -#25171,#25173,#25175,#25177)); -#25179=FACE_BOUND('',#25178,.F.); -#25181=ORIENTED_EDGE('',*,*,#25180,.T.); -#25183=ORIENTED_EDGE('',*,*,#25182,.T.); -#25185=ORIENTED_EDGE('',*,*,#25184,.T.); -#25187=ORIENTED_EDGE('',*,*,#25186,.T.); -#25189=ORIENTED_EDGE('',*,*,#25188,.T.); -#25191=ORIENTED_EDGE('',*,*,#25190,.T.); -#25193=ORIENTED_EDGE('',*,*,#25192,.T.); -#25195=ORIENTED_EDGE('',*,*,#25194,.T.); -#25197=ORIENTED_EDGE('',*,*,#25196,.T.); -#25199=ORIENTED_EDGE('',*,*,#25198,.T.); -#25201=ORIENTED_EDGE('',*,*,#25200,.T.); -#25203=ORIENTED_EDGE('',*,*,#25202,.T.); -#25205=ORIENTED_EDGE('',*,*,#25204,.T.); -#25207=ORIENTED_EDGE('',*,*,#25206,.T.); -#25209=ORIENTED_EDGE('',*,*,#25208,.T.); -#25211=ORIENTED_EDGE('',*,*,#25210,.T.); -#25213=ORIENTED_EDGE('',*,*,#25212,.T.); -#25215=ORIENTED_EDGE('',*,*,#25214,.T.); -#25217=ORIENTED_EDGE('',*,*,#25216,.T.); -#25219=ORIENTED_EDGE('',*,*,#25218,.T.); -#25221=ORIENTED_EDGE('',*,*,#25220,.T.); -#25223=ORIENTED_EDGE('',*,*,#25222,.T.); -#25225=ORIENTED_EDGE('',*,*,#25224,.T.); -#25227=ORIENTED_EDGE('',*,*,#25226,.T.); -#25229=ORIENTED_EDGE('',*,*,#25228,.T.); -#25231=ORIENTED_EDGE('',*,*,#25230,.T.); -#25233=ORIENTED_EDGE('',*,*,#25232,.T.); -#25235=ORIENTED_EDGE('',*,*,#25234,.T.); -#25237=ORIENTED_EDGE('',*,*,#25236,.T.); -#25239=ORIENTED_EDGE('',*,*,#25238,.T.); -#25241=ORIENTED_EDGE('',*,*,#25240,.T.); -#25243=ORIENTED_EDGE('',*,*,#25242,.T.); -#25245=ORIENTED_EDGE('',*,*,#25244,.T.); -#25247=ORIENTED_EDGE('',*,*,#25246,.T.); -#25248=EDGE_LOOP('',(#25181,#25183,#25185,#25187,#25189,#25191,#25193,#25195, -#25197,#25199,#25201,#25203,#25205,#25207,#25209,#25211,#25213,#25215,#25217, -#25219,#25221,#25223,#25225,#25227,#25229,#25231,#25233,#25235,#25237,#25239, -#25241,#25243,#25245,#25247)); -#25249=FACE_BOUND('',#25248,.F.); -#25251=ORIENTED_EDGE('',*,*,#25250,.T.); -#25253=ORIENTED_EDGE('',*,*,#25252,.T.); -#25255=ORIENTED_EDGE('',*,*,#25254,.T.); -#25257=ORIENTED_EDGE('',*,*,#25256,.T.); -#25259=ORIENTED_EDGE('',*,*,#25258,.T.); -#25261=ORIENTED_EDGE('',*,*,#25260,.T.); -#25263=ORIENTED_EDGE('',*,*,#25262,.T.); -#25265=ORIENTED_EDGE('',*,*,#25264,.T.); -#25267=ORIENTED_EDGE('',*,*,#25266,.T.); -#25269=ORIENTED_EDGE('',*,*,#25268,.T.); -#25271=ORIENTED_EDGE('',*,*,#25270,.T.); -#25273=ORIENTED_EDGE('',*,*,#25272,.T.); -#25275=ORIENTED_EDGE('',*,*,#25274,.T.); -#25276=EDGE_LOOP('',(#25251,#25253,#25255,#25257,#25259,#25261,#25263,#25265, -#25267,#25269,#25271,#25273,#25275)); -#25277=FACE_BOUND('',#25276,.F.); -#25279=ORIENTED_EDGE('',*,*,#25278,.T.); -#25281=ORIENTED_EDGE('',*,*,#25280,.T.); -#25283=ORIENTED_EDGE('',*,*,#25282,.T.); -#25285=ORIENTED_EDGE('',*,*,#25284,.T.); -#25287=ORIENTED_EDGE('',*,*,#25286,.T.); -#25289=ORIENTED_EDGE('',*,*,#25288,.T.); -#25291=ORIENTED_EDGE('',*,*,#25290,.T.); -#25293=ORIENTED_EDGE('',*,*,#25292,.T.); -#25295=ORIENTED_EDGE('',*,*,#25294,.T.); -#25297=ORIENTED_EDGE('',*,*,#25296,.T.); -#25299=ORIENTED_EDGE('',*,*,#25298,.T.); -#25301=ORIENTED_EDGE('',*,*,#25300,.T.); -#25303=ORIENTED_EDGE('',*,*,#25302,.T.); -#25305=ORIENTED_EDGE('',*,*,#25304,.T.); -#25307=ORIENTED_EDGE('',*,*,#25306,.T.); -#25309=ORIENTED_EDGE('',*,*,#25308,.T.); -#25311=ORIENTED_EDGE('',*,*,#25310,.T.); -#25313=ORIENTED_EDGE('',*,*,#25312,.T.); -#25315=ORIENTED_EDGE('',*,*,#25314,.T.); -#25316=EDGE_LOOP('',(#25279,#25281,#25283,#25285,#25287,#25289,#25291,#25293, -#25295,#25297,#25299,#25301,#25303,#25305,#25307,#25309,#25311,#25313,#25315)); -#25317=FACE_BOUND('',#25316,.F.); -#25319=ORIENTED_EDGE('',*,*,#25318,.T.); -#25321=ORIENTED_EDGE('',*,*,#25320,.T.); -#25323=ORIENTED_EDGE('',*,*,#25322,.T.); -#25325=ORIENTED_EDGE('',*,*,#25324,.T.); -#25327=ORIENTED_EDGE('',*,*,#25326,.T.); -#25329=ORIENTED_EDGE('',*,*,#25328,.T.); -#25331=ORIENTED_EDGE('',*,*,#25330,.T.); -#25333=ORIENTED_EDGE('',*,*,#25332,.T.); -#25334=EDGE_LOOP('',(#25319,#25321,#25323,#25325,#25327,#25329,#25331,#25333)); -#25335=FACE_BOUND('',#25334,.F.); -#25337=ORIENTED_EDGE('',*,*,#25336,.T.); -#25339=ORIENTED_EDGE('',*,*,#25338,.T.); -#25341=ORIENTED_EDGE('',*,*,#25340,.T.); -#25343=ORIENTED_EDGE('',*,*,#25342,.T.); -#25345=ORIENTED_EDGE('',*,*,#25344,.T.); -#25347=ORIENTED_EDGE('',*,*,#25346,.T.); -#25349=ORIENTED_EDGE('',*,*,#25348,.T.); -#25351=ORIENTED_EDGE('',*,*,#25350,.T.); -#25353=ORIENTED_EDGE('',*,*,#25352,.T.); -#25355=ORIENTED_EDGE('',*,*,#25354,.T.); -#25357=ORIENTED_EDGE('',*,*,#25356,.T.); -#25359=ORIENTED_EDGE('',*,*,#25358,.T.); -#25361=ORIENTED_EDGE('',*,*,#25360,.T.); -#25363=ORIENTED_EDGE('',*,*,#25362,.T.); -#25365=ORIENTED_EDGE('',*,*,#25364,.T.); -#25367=ORIENTED_EDGE('',*,*,#25366,.T.); -#25369=ORIENTED_EDGE('',*,*,#25368,.T.); -#25371=ORIENTED_EDGE('',*,*,#25370,.T.); -#25373=ORIENTED_EDGE('',*,*,#25372,.T.); -#25375=ORIENTED_EDGE('',*,*,#25374,.T.); -#25377=ORIENTED_EDGE('',*,*,#25376,.T.); -#25379=ORIENTED_EDGE('',*,*,#25378,.T.); -#25381=ORIENTED_EDGE('',*,*,#25380,.T.); -#25383=ORIENTED_EDGE('',*,*,#25382,.T.); -#25385=ORIENTED_EDGE('',*,*,#25384,.T.); -#25387=ORIENTED_EDGE('',*,*,#25386,.T.); -#25389=ORIENTED_EDGE('',*,*,#25388,.T.); -#25391=ORIENTED_EDGE('',*,*,#25390,.T.); -#25393=ORIENTED_EDGE('',*,*,#25392,.T.); -#25395=ORIENTED_EDGE('',*,*,#25394,.T.); -#25397=ORIENTED_EDGE('',*,*,#25396,.T.); -#25399=ORIENTED_EDGE('',*,*,#25398,.T.); -#25401=ORIENTED_EDGE('',*,*,#25400,.T.); -#25403=ORIENTED_EDGE('',*,*,#25402,.T.); -#25404=EDGE_LOOP('',(#25337,#25339,#25341,#25343,#25345,#25347,#25349,#25351, -#25353,#25355,#25357,#25359,#25361,#25363,#25365,#25367,#25369,#25371,#25373, -#25375,#25377,#25379,#25381,#25383,#25385,#25387,#25389,#25391,#25393,#25395, -#25397,#25399,#25401,#25403)); -#25405=FACE_BOUND('',#25404,.F.); -#25407=ORIENTED_EDGE('',*,*,#25406,.T.); -#25409=ORIENTED_EDGE('',*,*,#25408,.T.); -#25411=ORIENTED_EDGE('',*,*,#25410,.T.); -#25413=ORIENTED_EDGE('',*,*,#25412,.T.); -#25415=ORIENTED_EDGE('',*,*,#25414,.T.); -#25417=ORIENTED_EDGE('',*,*,#25416,.T.); -#25419=ORIENTED_EDGE('',*,*,#25418,.T.); -#25421=ORIENTED_EDGE('',*,*,#25420,.T.); -#25423=ORIENTED_EDGE('',*,*,#25422,.T.); -#25425=ORIENTED_EDGE('',*,*,#25424,.T.); -#25427=ORIENTED_EDGE('',*,*,#25426,.T.); -#25429=ORIENTED_EDGE('',*,*,#25428,.T.); -#25431=ORIENTED_EDGE('',*,*,#25430,.T.); -#25433=ORIENTED_EDGE('',*,*,#25432,.T.); -#25435=ORIENTED_EDGE('',*,*,#25434,.T.); -#25437=ORIENTED_EDGE('',*,*,#25436,.T.); -#25439=ORIENTED_EDGE('',*,*,#25438,.T.); -#25441=ORIENTED_EDGE('',*,*,#25440,.T.); -#25443=ORIENTED_EDGE('',*,*,#25442,.T.); -#25445=ORIENTED_EDGE('',*,*,#25444,.T.); -#25447=ORIENTED_EDGE('',*,*,#25446,.T.); -#25449=ORIENTED_EDGE('',*,*,#25448,.T.); -#25451=ORIENTED_EDGE('',*,*,#25450,.T.); -#25453=ORIENTED_EDGE('',*,*,#25452,.T.); -#25455=ORIENTED_EDGE('',*,*,#25454,.T.); -#25457=ORIENTED_EDGE('',*,*,#25456,.T.); -#25459=ORIENTED_EDGE('',*,*,#25458,.T.); -#25461=ORIENTED_EDGE('',*,*,#25460,.T.); -#25463=ORIENTED_EDGE('',*,*,#25462,.T.); -#25465=ORIENTED_EDGE('',*,*,#25464,.T.); -#25467=ORIENTED_EDGE('',*,*,#25466,.T.); -#25469=ORIENTED_EDGE('',*,*,#25468,.T.); -#25471=ORIENTED_EDGE('',*,*,#25470,.T.); -#25473=ORIENTED_EDGE('',*,*,#25472,.T.); -#25475=ORIENTED_EDGE('',*,*,#25474,.T.); -#25477=ORIENTED_EDGE('',*,*,#25476,.T.); -#25479=ORIENTED_EDGE('',*,*,#25478,.T.); -#25481=ORIENTED_EDGE('',*,*,#25480,.T.); -#25483=ORIENTED_EDGE('',*,*,#25482,.T.); -#25485=ORIENTED_EDGE('',*,*,#25484,.T.); -#25487=ORIENTED_EDGE('',*,*,#25486,.T.); -#25489=ORIENTED_EDGE('',*,*,#25488,.T.); -#25491=ORIENTED_EDGE('',*,*,#25490,.T.); -#25493=ORIENTED_EDGE('',*,*,#25492,.T.); -#25495=ORIENTED_EDGE('',*,*,#25494,.T.); -#25497=ORIENTED_EDGE('',*,*,#25496,.T.); -#25499=ORIENTED_EDGE('',*,*,#25498,.T.); -#25501=ORIENTED_EDGE('',*,*,#25500,.T.); -#25503=ORIENTED_EDGE('',*,*,#25502,.T.); -#25505=ORIENTED_EDGE('',*,*,#25504,.T.); -#25507=ORIENTED_EDGE('',*,*,#25506,.T.); -#25509=ORIENTED_EDGE('',*,*,#25508,.T.); -#25511=ORIENTED_EDGE('',*,*,#25510,.T.); -#25513=ORIENTED_EDGE('',*,*,#25512,.T.); -#25515=ORIENTED_EDGE('',*,*,#25514,.T.); -#25517=ORIENTED_EDGE('',*,*,#25516,.T.); -#25519=ORIENTED_EDGE('',*,*,#25518,.T.); -#25520=EDGE_LOOP('',(#25407,#25409,#25411,#25413,#25415,#25417,#25419,#25421, -#25423,#25425,#25427,#25429,#25431,#25433,#25435,#25437,#25439,#25441,#25443, -#25445,#25447,#25449,#25451,#25453,#25455,#25457,#25459,#25461,#25463,#25465, -#25467,#25469,#25471,#25473,#25475,#25477,#25479,#25481,#25483,#25485,#25487, -#25489,#25491,#25493,#25495,#25497,#25499,#25501,#25503,#25505,#25507,#25509, -#25511,#25513,#25515,#25517,#25519)); -#25521=FACE_BOUND('',#25520,.F.); -#25523=ORIENTED_EDGE('',*,*,#25522,.T.); -#25525=ORIENTED_EDGE('',*,*,#25524,.T.); -#25527=ORIENTED_EDGE('',*,*,#25526,.T.); -#25529=ORIENTED_EDGE('',*,*,#25528,.T.); -#25531=ORIENTED_EDGE('',*,*,#25530,.T.); -#25533=ORIENTED_EDGE('',*,*,#25532,.T.); -#25535=ORIENTED_EDGE('',*,*,#25534,.T.); -#25537=ORIENTED_EDGE('',*,*,#25536,.T.); -#25539=ORIENTED_EDGE('',*,*,#25538,.T.); -#25541=ORIENTED_EDGE('',*,*,#25540,.T.); -#25543=ORIENTED_EDGE('',*,*,#25542,.T.); -#25545=ORIENTED_EDGE('',*,*,#25544,.T.); -#25547=ORIENTED_EDGE('',*,*,#25546,.T.); -#25549=ORIENTED_EDGE('',*,*,#25548,.T.); -#25551=ORIENTED_EDGE('',*,*,#25550,.T.); -#25553=ORIENTED_EDGE('',*,*,#25552,.T.); -#25555=ORIENTED_EDGE('',*,*,#25554,.T.); -#25557=ORIENTED_EDGE('',*,*,#25556,.T.); -#25559=ORIENTED_EDGE('',*,*,#25558,.T.); -#25561=ORIENTED_EDGE('',*,*,#25560,.T.); -#25563=ORIENTED_EDGE('',*,*,#25562,.T.); -#25565=ORIENTED_EDGE('',*,*,#25564,.T.); -#25567=ORIENTED_EDGE('',*,*,#25566,.T.); -#25569=ORIENTED_EDGE('',*,*,#25568,.T.); -#25571=ORIENTED_EDGE('',*,*,#25570,.T.); -#25573=ORIENTED_EDGE('',*,*,#25572,.T.); -#25575=ORIENTED_EDGE('',*,*,#25574,.T.); -#25577=ORIENTED_EDGE('',*,*,#25576,.T.); -#25578=EDGE_LOOP('',(#25523,#25525,#25527,#25529,#25531,#25533,#25535,#25537, -#25539,#25541,#25543,#25545,#25547,#25549,#25551,#25553,#25555,#25557,#25559, -#25561,#25563,#25565,#25567,#25569,#25571,#25573,#25575,#25577)); -#25579=FACE_BOUND('',#25578,.F.); -#25581=ORIENTED_EDGE('',*,*,#25580,.T.); -#25583=ORIENTED_EDGE('',*,*,#25582,.T.); -#25585=ORIENTED_EDGE('',*,*,#25584,.T.); -#25587=ORIENTED_EDGE('',*,*,#25586,.T.); -#25588=EDGE_LOOP('',(#25581,#25583,#25585,#25587)); -#25589=FACE_BOUND('',#25588,.F.); -#25591=ORIENTED_EDGE('',*,*,#25590,.T.); -#25593=ORIENTED_EDGE('',*,*,#25592,.T.); -#25595=ORIENTED_EDGE('',*,*,#25594,.T.); -#25597=ORIENTED_EDGE('',*,*,#25596,.T.); -#25599=ORIENTED_EDGE('',*,*,#25598,.T.); -#25601=ORIENTED_EDGE('',*,*,#25600,.T.); -#25603=ORIENTED_EDGE('',*,*,#25602,.T.); -#25605=ORIENTED_EDGE('',*,*,#25604,.T.); -#25607=ORIENTED_EDGE('',*,*,#25606,.T.); -#25609=ORIENTED_EDGE('',*,*,#25608,.T.); -#25611=ORIENTED_EDGE('',*,*,#25610,.T.); -#25613=ORIENTED_EDGE('',*,*,#25612,.T.); -#25615=ORIENTED_EDGE('',*,*,#25614,.T.); -#25617=ORIENTED_EDGE('',*,*,#25616,.T.); -#25619=ORIENTED_EDGE('',*,*,#25618,.T.); -#25621=ORIENTED_EDGE('',*,*,#25620,.T.); -#25623=ORIENTED_EDGE('',*,*,#25622,.T.); -#25625=ORIENTED_EDGE('',*,*,#25624,.T.); -#25627=ORIENTED_EDGE('',*,*,#25626,.T.); -#25629=ORIENTED_EDGE('',*,*,#25628,.T.); -#25631=ORIENTED_EDGE('',*,*,#25630,.T.); -#25633=ORIENTED_EDGE('',*,*,#25632,.T.); -#25635=ORIENTED_EDGE('',*,*,#25634,.T.); -#25637=ORIENTED_EDGE('',*,*,#25636,.T.); -#25639=ORIENTED_EDGE('',*,*,#25638,.T.); -#25641=ORIENTED_EDGE('',*,*,#25640,.T.); -#25643=ORIENTED_EDGE('',*,*,#25642,.T.); -#25645=ORIENTED_EDGE('',*,*,#25644,.T.); -#25647=ORIENTED_EDGE('',*,*,#25646,.T.); -#25649=ORIENTED_EDGE('',*,*,#25648,.T.); -#25651=ORIENTED_EDGE('',*,*,#25650,.T.); -#25653=ORIENTED_EDGE('',*,*,#25652,.T.); -#25655=ORIENTED_EDGE('',*,*,#25654,.T.); -#25657=ORIENTED_EDGE('',*,*,#25656,.T.); -#25659=ORIENTED_EDGE('',*,*,#25658,.T.); -#25661=ORIENTED_EDGE('',*,*,#25660,.T.); -#25663=ORIENTED_EDGE('',*,*,#25662,.T.); -#25665=ORIENTED_EDGE('',*,*,#25664,.T.); -#25667=ORIENTED_EDGE('',*,*,#25666,.T.); -#25669=ORIENTED_EDGE('',*,*,#25668,.T.); -#25670=EDGE_LOOP('',(#25591,#25593,#25595,#25597,#25599,#25601,#25603,#25605, -#25607,#25609,#25611,#25613,#25615,#25617,#25619,#25621,#25623,#25625,#25627, -#25629,#25631,#25633,#25635,#25637,#25639,#25641,#25643,#25645,#25647,#25649, -#25651,#25653,#25655,#25657,#25659,#25661,#25663,#25665,#25667,#25669)); -#25671=FACE_BOUND('',#25670,.F.); -#25673=ORIENTED_EDGE('',*,*,#25672,.T.); -#25675=ORIENTED_EDGE('',*,*,#25674,.T.); -#25677=ORIENTED_EDGE('',*,*,#25676,.T.); -#25679=ORIENTED_EDGE('',*,*,#25678,.T.); -#25680=EDGE_LOOP('',(#25673,#25675,#25677,#25679)); -#25681=FACE_BOUND('',#25680,.F.); -#25683=ORIENTED_EDGE('',*,*,#25682,.T.); -#25685=ORIENTED_EDGE('',*,*,#25684,.T.); -#25687=ORIENTED_EDGE('',*,*,#25686,.T.); -#25689=ORIENTED_EDGE('',*,*,#25688,.T.); -#25691=ORIENTED_EDGE('',*,*,#25690,.T.); -#25693=ORIENTED_EDGE('',*,*,#25692,.T.); -#25695=ORIENTED_EDGE('',*,*,#25694,.T.); -#25697=ORIENTED_EDGE('',*,*,#25696,.T.); -#25699=ORIENTED_EDGE('',*,*,#25698,.T.); -#25701=ORIENTED_EDGE('',*,*,#25700,.T.); -#25703=ORIENTED_EDGE('',*,*,#25702,.T.); -#25705=ORIENTED_EDGE('',*,*,#25704,.T.); -#25707=ORIENTED_EDGE('',*,*,#25706,.T.); -#25709=ORIENTED_EDGE('',*,*,#25708,.T.); -#25710=EDGE_LOOP('',(#25683,#25685,#25687,#25689,#25691,#25693,#25695,#25697, -#25699,#25701,#25703,#25705,#25707,#25709)); -#25711=FACE_BOUND('',#25710,.F.); -#25713=ORIENTED_EDGE('',*,*,#25712,.T.); -#25715=ORIENTED_EDGE('',*,*,#25714,.T.); -#25717=ORIENTED_EDGE('',*,*,#25716,.T.); -#25719=ORIENTED_EDGE('',*,*,#25718,.T.); -#25720=EDGE_LOOP('',(#25713,#25715,#25717,#25719)); -#25721=FACE_BOUND('',#25720,.F.); -#25723=ORIENTED_EDGE('',*,*,#25722,.T.); -#25725=ORIENTED_EDGE('',*,*,#25724,.T.); -#25727=ORIENTED_EDGE('',*,*,#25726,.T.); -#25729=ORIENTED_EDGE('',*,*,#25728,.T.); -#25730=EDGE_LOOP('',(#25723,#25725,#25727,#25729)); -#25731=FACE_BOUND('',#25730,.F.); -#25733=ORIENTED_EDGE('',*,*,#25732,.T.); -#25735=ORIENTED_EDGE('',*,*,#25734,.T.); -#25737=ORIENTED_EDGE('',*,*,#25736,.T.); -#25739=ORIENTED_EDGE('',*,*,#25738,.T.); -#25741=ORIENTED_EDGE('',*,*,#25740,.T.); -#25743=ORIENTED_EDGE('',*,*,#25742,.T.); -#25745=ORIENTED_EDGE('',*,*,#25744,.T.); -#25747=ORIENTED_EDGE('',*,*,#25746,.T.); -#25749=ORIENTED_EDGE('',*,*,#25748,.T.); -#25751=ORIENTED_EDGE('',*,*,#25750,.T.); -#25753=ORIENTED_EDGE('',*,*,#25752,.T.); -#25754=EDGE_LOOP('',(#25733,#25735,#25737,#25739,#25741,#25743,#25745,#25747, -#25749,#25751,#25753)); -#25755=FACE_BOUND('',#25754,.F.); -#25757=ORIENTED_EDGE('',*,*,#25756,.T.); -#25759=ORIENTED_EDGE('',*,*,#25758,.T.); -#25761=ORIENTED_EDGE('',*,*,#25760,.T.); -#25763=ORIENTED_EDGE('',*,*,#25762,.T.); -#25765=ORIENTED_EDGE('',*,*,#25764,.T.); -#25767=ORIENTED_EDGE('',*,*,#25766,.T.); -#25769=ORIENTED_EDGE('',*,*,#25768,.T.); -#25770=EDGE_LOOP('',(#25757,#25759,#25761,#25763,#25765,#25767,#25769)); -#25771=FACE_BOUND('',#25770,.F.); -#25773=ORIENTED_EDGE('',*,*,#25772,.T.); -#25775=ORIENTED_EDGE('',*,*,#25774,.T.); -#25777=ORIENTED_EDGE('',*,*,#25776,.T.); -#25779=ORIENTED_EDGE('',*,*,#25778,.T.); -#25781=ORIENTED_EDGE('',*,*,#25780,.T.); -#25783=ORIENTED_EDGE('',*,*,#25782,.T.); -#25785=ORIENTED_EDGE('',*,*,#25784,.T.); -#25787=ORIENTED_EDGE('',*,*,#25786,.T.); -#25789=ORIENTED_EDGE('',*,*,#25788,.T.); -#25791=ORIENTED_EDGE('',*,*,#25790,.T.); -#25793=ORIENTED_EDGE('',*,*,#25792,.T.); -#25795=ORIENTED_EDGE('',*,*,#25794,.T.); -#25797=ORIENTED_EDGE('',*,*,#25796,.T.); -#25799=ORIENTED_EDGE('',*,*,#25798,.T.); -#25801=ORIENTED_EDGE('',*,*,#25800,.T.); -#25803=ORIENTED_EDGE('',*,*,#25802,.T.); -#25805=ORIENTED_EDGE('',*,*,#25804,.T.); -#25807=ORIENTED_EDGE('',*,*,#25806,.T.); -#25809=ORIENTED_EDGE('',*,*,#25808,.T.); -#25811=ORIENTED_EDGE('',*,*,#25810,.T.); -#25813=ORIENTED_EDGE('',*,*,#25812,.T.); -#25815=ORIENTED_EDGE('',*,*,#25814,.T.); -#25817=ORIENTED_EDGE('',*,*,#25816,.T.); -#25819=ORIENTED_EDGE('',*,*,#25818,.T.); -#25821=ORIENTED_EDGE('',*,*,#25820,.T.); -#25823=ORIENTED_EDGE('',*,*,#25822,.T.); -#25824=EDGE_LOOP('',(#25773,#25775,#25777,#25779,#25781,#25783,#25785,#25787, -#25789,#25791,#25793,#25795,#25797,#25799,#25801,#25803,#25805,#25807,#25809, -#25811,#25813,#25815,#25817,#25819,#25821,#25823)); -#25825=FACE_BOUND('',#25824,.F.); -#25827=ORIENTED_EDGE('',*,*,#25826,.T.); -#25829=ORIENTED_EDGE('',*,*,#25828,.T.); -#25831=ORIENTED_EDGE('',*,*,#25830,.T.); -#25833=ORIENTED_EDGE('',*,*,#25832,.T.); -#25835=ORIENTED_EDGE('',*,*,#25834,.T.); -#25837=ORIENTED_EDGE('',*,*,#25836,.T.); -#25839=ORIENTED_EDGE('',*,*,#25838,.T.); -#25841=ORIENTED_EDGE('',*,*,#25840,.T.); -#25843=ORIENTED_EDGE('',*,*,#25842,.T.); -#25845=ORIENTED_EDGE('',*,*,#25844,.T.); -#25847=ORIENTED_EDGE('',*,*,#25846,.T.); -#25849=ORIENTED_EDGE('',*,*,#25848,.T.); -#25851=ORIENTED_EDGE('',*,*,#25850,.T.); -#25853=ORIENTED_EDGE('',*,*,#25852,.T.); -#25855=ORIENTED_EDGE('',*,*,#25854,.T.); -#25857=ORIENTED_EDGE('',*,*,#25856,.T.); -#25859=ORIENTED_EDGE('',*,*,#25858,.T.); -#25861=ORIENTED_EDGE('',*,*,#25860,.T.); -#25863=ORIENTED_EDGE('',*,*,#25862,.T.); -#25865=ORIENTED_EDGE('',*,*,#25864,.T.); -#25867=ORIENTED_EDGE('',*,*,#25866,.T.); -#25869=ORIENTED_EDGE('',*,*,#25868,.T.); -#25871=ORIENTED_EDGE('',*,*,#25870,.T.); -#25873=ORIENTED_EDGE('',*,*,#25872,.T.); -#25875=ORIENTED_EDGE('',*,*,#25874,.T.); -#25877=ORIENTED_EDGE('',*,*,#25876,.T.); -#25878=EDGE_LOOP('',(#25827,#25829,#25831,#25833,#25835,#25837,#25839,#25841, -#25843,#25845,#25847,#25849,#25851,#25853,#25855,#25857,#25859,#25861,#25863, -#25865,#25867,#25869,#25871,#25873,#25875,#25877)); -#25879=FACE_BOUND('',#25878,.F.); -#25881=ORIENTED_EDGE('',*,*,#25880,.T.); -#25883=ORIENTED_EDGE('',*,*,#25882,.T.); -#25885=ORIENTED_EDGE('',*,*,#25884,.T.); -#25887=ORIENTED_EDGE('',*,*,#25886,.T.); -#25889=ORIENTED_EDGE('',*,*,#25888,.T.); -#25891=ORIENTED_EDGE('',*,*,#25890,.T.); -#25893=ORIENTED_EDGE('',*,*,#25892,.T.); -#25895=ORIENTED_EDGE('',*,*,#25894,.T.); -#25896=EDGE_LOOP('',(#25881,#25883,#25885,#25887,#25889,#25891,#25893,#25895)); -#25897=FACE_BOUND('',#25896,.F.); -#25899=ORIENTED_EDGE('',*,*,#25898,.T.); -#25901=ORIENTED_EDGE('',*,*,#25900,.T.); -#25903=ORIENTED_EDGE('',*,*,#25902,.T.); -#25905=ORIENTED_EDGE('',*,*,#25904,.T.); -#25906=EDGE_LOOP('',(#25899,#25901,#25903,#25905)); -#25907=FACE_BOUND('',#25906,.F.); -#25909=ORIENTED_EDGE('',*,*,#25908,.T.); -#25911=ORIENTED_EDGE('',*,*,#25910,.T.); -#25913=ORIENTED_EDGE('',*,*,#25912,.T.); -#25915=ORIENTED_EDGE('',*,*,#25914,.T.); -#25917=ORIENTED_EDGE('',*,*,#25916,.T.); -#25919=ORIENTED_EDGE('',*,*,#25918,.T.); -#25921=ORIENTED_EDGE('',*,*,#25920,.T.); -#25923=ORIENTED_EDGE('',*,*,#25922,.T.); -#25925=ORIENTED_EDGE('',*,*,#25924,.T.); -#25927=ORIENTED_EDGE('',*,*,#25926,.T.); -#25929=ORIENTED_EDGE('',*,*,#25928,.T.); -#25931=ORIENTED_EDGE('',*,*,#25930,.T.); -#25933=ORIENTED_EDGE('',*,*,#25932,.T.); -#25935=ORIENTED_EDGE('',*,*,#25934,.T.); -#25937=ORIENTED_EDGE('',*,*,#25936,.T.); -#25939=ORIENTED_EDGE('',*,*,#25938,.T.); -#25941=ORIENTED_EDGE('',*,*,#25940,.T.); -#25943=ORIENTED_EDGE('',*,*,#25942,.T.); -#25945=ORIENTED_EDGE('',*,*,#25944,.T.); -#25946=EDGE_LOOP('',(#25909,#25911,#25913,#25915,#25917,#25919,#25921,#25923, -#25925,#25927,#25929,#25931,#25933,#25935,#25937,#25939,#25941,#25943,#25945)); -#25947=FACE_BOUND('',#25946,.F.); -#25949=ORIENTED_EDGE('',*,*,#25948,.T.); -#25951=ORIENTED_EDGE('',*,*,#25950,.T.); -#25953=ORIENTED_EDGE('',*,*,#25952,.T.); -#25955=ORIENTED_EDGE('',*,*,#25954,.T.); -#25957=ORIENTED_EDGE('',*,*,#25956,.T.); -#25959=ORIENTED_EDGE('',*,*,#25958,.T.); -#25961=ORIENTED_EDGE('',*,*,#25960,.T.); -#25963=ORIENTED_EDGE('',*,*,#25962,.T.); -#25964=EDGE_LOOP('',(#25949,#25951,#25953,#25955,#25957,#25959,#25961,#25963)); -#25965=FACE_BOUND('',#25964,.F.); -#25967=ORIENTED_EDGE('',*,*,#25966,.T.); -#25969=ORIENTED_EDGE('',*,*,#25968,.T.); -#25971=ORIENTED_EDGE('',*,*,#25970,.T.); -#25973=ORIENTED_EDGE('',*,*,#25972,.T.); -#25975=ORIENTED_EDGE('',*,*,#25974,.T.); -#25977=ORIENTED_EDGE('',*,*,#25976,.T.); -#25979=ORIENTED_EDGE('',*,*,#25978,.T.); -#25981=ORIENTED_EDGE('',*,*,#25980,.T.); -#25983=ORIENTED_EDGE('',*,*,#25982,.T.); -#25985=ORIENTED_EDGE('',*,*,#25984,.T.); -#25987=ORIENTED_EDGE('',*,*,#25986,.T.); -#25989=ORIENTED_EDGE('',*,*,#25988,.T.); -#25991=ORIENTED_EDGE('',*,*,#25990,.T.); -#25993=ORIENTED_EDGE('',*,*,#25992,.T.); -#25995=ORIENTED_EDGE('',*,*,#25994,.T.); -#25997=ORIENTED_EDGE('',*,*,#25996,.T.); -#25999=ORIENTED_EDGE('',*,*,#25998,.T.); -#26001=ORIENTED_EDGE('',*,*,#26000,.T.); -#26003=ORIENTED_EDGE('',*,*,#26002,.T.); -#26005=ORIENTED_EDGE('',*,*,#26004,.T.); -#26007=ORIENTED_EDGE('',*,*,#26006,.T.); -#26009=ORIENTED_EDGE('',*,*,#26008,.T.); -#26011=ORIENTED_EDGE('',*,*,#26010,.T.); -#26013=ORIENTED_EDGE('',*,*,#26012,.T.); -#26015=ORIENTED_EDGE('',*,*,#26014,.T.); -#26017=ORIENTED_EDGE('',*,*,#26016,.T.); -#26019=ORIENTED_EDGE('',*,*,#26018,.T.); -#26021=ORIENTED_EDGE('',*,*,#26020,.T.); -#26023=ORIENTED_EDGE('',*,*,#26022,.T.); -#26025=ORIENTED_EDGE('',*,*,#26024,.T.); -#26027=ORIENTED_EDGE('',*,*,#26026,.T.); -#26029=ORIENTED_EDGE('',*,*,#26028,.T.); -#26031=ORIENTED_EDGE('',*,*,#26030,.T.); -#26033=ORIENTED_EDGE('',*,*,#26032,.T.); -#26034=EDGE_LOOP('',(#25967,#25969,#25971,#25973,#25975,#25977,#25979,#25981, -#25983,#25985,#25987,#25989,#25991,#25993,#25995,#25997,#25999,#26001,#26003, -#26005,#26007,#26009,#26011,#26013,#26015,#26017,#26019,#26021,#26023,#26025, -#26027,#26029,#26031,#26033)); -#26035=FACE_BOUND('',#26034,.F.); -#26037=ORIENTED_EDGE('',*,*,#26036,.T.); -#26039=ORIENTED_EDGE('',*,*,#26038,.T.); -#26041=ORIENTED_EDGE('',*,*,#26040,.T.); -#26043=ORIENTED_EDGE('',*,*,#26042,.T.); -#26045=ORIENTED_EDGE('',*,*,#26044,.T.); -#26047=ORIENTED_EDGE('',*,*,#26046,.T.); -#26049=ORIENTED_EDGE('',*,*,#26048,.T.); -#26051=ORIENTED_EDGE('',*,*,#26050,.T.); -#26053=ORIENTED_EDGE('',*,*,#26052,.T.); -#26055=ORIENTED_EDGE('',*,*,#26054,.T.); -#26057=ORIENTED_EDGE('',*,*,#26056,.T.); -#26059=ORIENTED_EDGE('',*,*,#26058,.T.); -#26061=ORIENTED_EDGE('',*,*,#26060,.T.); -#26063=ORIENTED_EDGE('',*,*,#26062,.T.); -#26065=ORIENTED_EDGE('',*,*,#26064,.T.); -#26067=ORIENTED_EDGE('',*,*,#26066,.T.); -#26069=ORIENTED_EDGE('',*,*,#26068,.T.); -#26071=ORIENTED_EDGE('',*,*,#26070,.T.); -#26073=ORIENTED_EDGE('',*,*,#26072,.T.); -#26075=ORIENTED_EDGE('',*,*,#26074,.T.); -#26077=ORIENTED_EDGE('',*,*,#26076,.T.); -#26079=ORIENTED_EDGE('',*,*,#26078,.T.); -#26081=ORIENTED_EDGE('',*,*,#26080,.T.); -#26083=ORIENTED_EDGE('',*,*,#26082,.T.); -#26085=ORIENTED_EDGE('',*,*,#26084,.T.); -#26087=ORIENTED_EDGE('',*,*,#26086,.T.); -#26089=ORIENTED_EDGE('',*,*,#26088,.T.); -#26091=ORIENTED_EDGE('',*,*,#26090,.T.); -#26093=ORIENTED_EDGE('',*,*,#26092,.T.); -#26095=ORIENTED_EDGE('',*,*,#26094,.T.); -#26097=ORIENTED_EDGE('',*,*,#26096,.T.); -#26099=ORIENTED_EDGE('',*,*,#26098,.T.); -#26101=ORIENTED_EDGE('',*,*,#26100,.T.); -#26103=ORIENTED_EDGE('',*,*,#26102,.T.); -#26105=ORIENTED_EDGE('',*,*,#26104,.T.); -#26107=ORIENTED_EDGE('',*,*,#26106,.T.); -#26109=ORIENTED_EDGE('',*,*,#26108,.T.); -#26111=ORIENTED_EDGE('',*,*,#26110,.T.); -#26113=ORIENTED_EDGE('',*,*,#26112,.T.); -#26115=ORIENTED_EDGE('',*,*,#26114,.T.); -#26117=ORIENTED_EDGE('',*,*,#26116,.T.); -#26119=ORIENTED_EDGE('',*,*,#26118,.T.); -#26121=ORIENTED_EDGE('',*,*,#26120,.T.); -#26123=ORIENTED_EDGE('',*,*,#26122,.T.); -#26125=ORIENTED_EDGE('',*,*,#26124,.T.); -#26127=ORIENTED_EDGE('',*,*,#26126,.T.); -#26129=ORIENTED_EDGE('',*,*,#26128,.T.); -#26131=ORIENTED_EDGE('',*,*,#26130,.T.); -#26133=ORIENTED_EDGE('',*,*,#26132,.T.); -#26135=ORIENTED_EDGE('',*,*,#26134,.T.); -#26137=ORIENTED_EDGE('',*,*,#26136,.T.); -#26139=ORIENTED_EDGE('',*,*,#26138,.T.); -#26141=ORIENTED_EDGE('',*,*,#26140,.T.); -#26143=ORIENTED_EDGE('',*,*,#26142,.T.); -#26145=ORIENTED_EDGE('',*,*,#26144,.T.); -#26147=ORIENTED_EDGE('',*,*,#26146,.T.); -#26149=ORIENTED_EDGE('',*,*,#26148,.T.); -#26150=EDGE_LOOP('',(#26037,#26039,#26041,#26043,#26045,#26047,#26049,#26051, -#26053,#26055,#26057,#26059,#26061,#26063,#26065,#26067,#26069,#26071,#26073, -#26075,#26077,#26079,#26081,#26083,#26085,#26087,#26089,#26091,#26093,#26095, -#26097,#26099,#26101,#26103,#26105,#26107,#26109,#26111,#26113,#26115,#26117, -#26119,#26121,#26123,#26125,#26127,#26129,#26131,#26133,#26135,#26137,#26139, -#26141,#26143,#26145,#26147,#26149)); -#26151=FACE_BOUND('',#26150,.F.); -#26153=ORIENTED_EDGE('',*,*,#26152,.T.); -#26155=ORIENTED_EDGE('',*,*,#26154,.T.); -#26157=ORIENTED_EDGE('',*,*,#26156,.T.); -#26159=ORIENTED_EDGE('',*,*,#26158,.T.); -#26161=ORIENTED_EDGE('',*,*,#26160,.T.); -#26163=ORIENTED_EDGE('',*,*,#26162,.T.); -#26165=ORIENTED_EDGE('',*,*,#26164,.T.); -#26167=ORIENTED_EDGE('',*,*,#26166,.T.); -#26169=ORIENTED_EDGE('',*,*,#26168,.T.); -#26171=ORIENTED_EDGE('',*,*,#26170,.T.); -#26173=ORIENTED_EDGE('',*,*,#26172,.T.); -#26175=ORIENTED_EDGE('',*,*,#26174,.T.); -#26177=ORIENTED_EDGE('',*,*,#26176,.T.); -#26179=ORIENTED_EDGE('',*,*,#26178,.T.); -#26181=ORIENTED_EDGE('',*,*,#26180,.T.); -#26183=ORIENTED_EDGE('',*,*,#26182,.T.); -#26185=ORIENTED_EDGE('',*,*,#26184,.T.); -#26187=ORIENTED_EDGE('',*,*,#26186,.T.); -#26189=ORIENTED_EDGE('',*,*,#26188,.T.); -#26191=ORIENTED_EDGE('',*,*,#26190,.T.); -#26193=ORIENTED_EDGE('',*,*,#26192,.T.); -#26195=ORIENTED_EDGE('',*,*,#26194,.T.); -#26197=ORIENTED_EDGE('',*,*,#26196,.T.); -#26199=ORIENTED_EDGE('',*,*,#26198,.T.); -#26201=ORIENTED_EDGE('',*,*,#26200,.T.); -#26203=ORIENTED_EDGE('',*,*,#26202,.T.); -#26205=ORIENTED_EDGE('',*,*,#26204,.T.); -#26207=ORIENTED_EDGE('',*,*,#26206,.T.); -#26208=EDGE_LOOP('',(#26153,#26155,#26157,#26159,#26161,#26163,#26165,#26167, -#26169,#26171,#26173,#26175,#26177,#26179,#26181,#26183,#26185,#26187,#26189, -#26191,#26193,#26195,#26197,#26199,#26201,#26203,#26205,#26207)); -#26209=FACE_BOUND('',#26208,.F.); -#26211=ORIENTED_EDGE('',*,*,#26210,.T.); -#26213=ORIENTED_EDGE('',*,*,#26212,.T.); -#26215=ORIENTED_EDGE('',*,*,#26214,.T.); -#26217=ORIENTED_EDGE('',*,*,#26216,.F.); -#26218=EDGE_LOOP('',(#26211,#26213,#26215,#26217)); -#26219=FACE_BOUND('',#26218,.F.); -#26221=ORIENTED_EDGE('',*,*,#26220,.T.); -#26223=ORIENTED_EDGE('',*,*,#26222,.T.); -#26224=EDGE_LOOP('',(#26221,#26223)); -#26225=FACE_BOUND('',#26224,.F.); -#26227=ORIENTED_EDGE('',*,*,#26226,.F.); -#26229=ORIENTED_EDGE('',*,*,#26228,.T.); -#26231=ORIENTED_EDGE('',*,*,#26230,.F.); -#26233=ORIENTED_EDGE('',*,*,#26232,.T.); -#26235=ORIENTED_EDGE('',*,*,#26234,.F.); -#26237=ORIENTED_EDGE('',*,*,#26236,.T.); -#26239=ORIENTED_EDGE('',*,*,#26238,.T.); -#26241=ORIENTED_EDGE('',*,*,#26240,.F.); -#26243=ORIENTED_EDGE('',*,*,#26242,.T.); -#26245=ORIENTED_EDGE('',*,*,#26244,.F.); -#26246=EDGE_LOOP('',(#26227,#26229,#26231,#26233,#26235,#26237,#26239,#26241, -#26243,#26245)); -#26247=FACE_BOUND('',#26246,.F.); -#26249=ORIENTED_EDGE('',*,*,#26248,.T.); -#26251=ORIENTED_EDGE('',*,*,#26250,.F.); -#26253=ORIENTED_EDGE('',*,*,#26252,.T.); -#26255=ORIENTED_EDGE('',*,*,#26254,.F.); -#26257=ORIENTED_EDGE('',*,*,#26256,.T.); -#26259=ORIENTED_EDGE('',*,*,#26258,.F.); -#26261=ORIENTED_EDGE('',*,*,#26260,.T.); -#26263=ORIENTED_EDGE('',*,*,#26262,.F.); -#26264=EDGE_LOOP('',(#26249,#26251,#26253,#26255,#26257,#26259,#26261,#26263)); -#26265=FACE_BOUND('',#26264,.F.); -#26267=ORIENTED_EDGE('',*,*,#26266,.T.); -#26269=ORIENTED_EDGE('',*,*,#26268,.F.); -#26271=ORIENTED_EDGE('',*,*,#26270,.T.); -#26273=ORIENTED_EDGE('',*,*,#26272,.F.); -#26275=ORIENTED_EDGE('',*,*,#26274,.T.); -#26277=ORIENTED_EDGE('',*,*,#26276,.F.); -#26279=ORIENTED_EDGE('',*,*,#26278,.T.); -#26281=ORIENTED_EDGE('',*,*,#26280,.F.); -#26283=ORIENTED_EDGE('',*,*,#26282,.T.); -#26285=ORIENTED_EDGE('',*,*,#26284,.F.); -#26286=EDGE_LOOP('',(#26267,#26269,#26271,#26273,#26275,#26277,#26279,#26281, -#26283,#26285)); -#26287=FACE_BOUND('',#26286,.F.); -#26289=ORIENTED_EDGE('',*,*,#26288,.T.); -#26291=ORIENTED_EDGE('',*,*,#26290,.T.); -#26293=ORIENTED_EDGE('',*,*,#26292,.F.); -#26295=ORIENTED_EDGE('',*,*,#26294,.T.); -#26297=ORIENTED_EDGE('',*,*,#26296,.T.); -#26299=ORIENTED_EDGE('',*,*,#26298,.T.); -#26301=ORIENTED_EDGE('',*,*,#26300,.F.); -#26303=ORIENTED_EDGE('',*,*,#26302,.T.); -#26305=ORIENTED_EDGE('',*,*,#26304,.F.); -#26307=ORIENTED_EDGE('',*,*,#26306,.T.); -#26309=ORIENTED_EDGE('',*,*,#26308,.F.); -#26311=ORIENTED_EDGE('',*,*,#26310,.T.); -#26313=ORIENTED_EDGE('',*,*,#26312,.T.); -#26315=ORIENTED_EDGE('',*,*,#26314,.T.); -#26317=ORIENTED_EDGE('',*,*,#26316,.T.); -#26319=ORIENTED_EDGE('',*,*,#26318,.T.); -#26321=ORIENTED_EDGE('',*,*,#26320,.T.); -#26323=ORIENTED_EDGE('',*,*,#26322,.F.); -#26325=ORIENTED_EDGE('',*,*,#26324,.T.); -#26326=EDGE_LOOP('',(#26289,#26291,#26293,#26295,#26297,#26299,#26301,#26303, -#26305,#26307,#26309,#26311,#26313,#26315,#26317,#26319,#26321,#26323,#26325)); -#26327=FACE_BOUND('',#26326,.F.); -#26329=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26330=DIRECTION('',(0.E0,1.E0,0.E0)); -#26331=DIRECTION('',(1.E0,0.E0,0.E0)); -#26332=AXIS2_PLACEMENT_3D('',#26329,#26330,#26331); -#26333=PLANE('',#26332); -#26335=ORIENTED_EDGE('',*,*,#26334,.T.); -#26337=ORIENTED_EDGE('',*,*,#26336,.T.); -#26339=ORIENTED_EDGE('',*,*,#26338,.T.); -#26341=ORIENTED_EDGE('',*,*,#26340,.T.); -#26343=ORIENTED_EDGE('',*,*,#26342,.T.); -#26345=ORIENTED_EDGE('',*,*,#26344,.T.); -#26347=ORIENTED_EDGE('',*,*,#26346,.T.); -#26349=ORIENTED_EDGE('',*,*,#26348,.T.); -#26351=ORIENTED_EDGE('',*,*,#26350,.T.); -#26353=ORIENTED_EDGE('',*,*,#26352,.T.); -#26354=EDGE_LOOP('',(#26335,#26337,#26339,#26341,#26343,#26345,#26347,#26349, -#26351,#26353)); -#26355=FACE_OUTER_BOUND('',#26354,.F.); -#26357=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26358=DIRECTION('',(0.E0,1.E0,0.E0)); -#26359=DIRECTION('',(1.E0,0.E0,0.E0)); -#26360=AXIS2_PLACEMENT_3D('',#26357,#26358,#26359); -#26361=PLANE('',#26360); -#26363=ORIENTED_EDGE('',*,*,#26362,.T.); -#26365=ORIENTED_EDGE('',*,*,#26364,.T.); -#26367=ORIENTED_EDGE('',*,*,#26366,.T.); -#26369=ORIENTED_EDGE('',*,*,#26368,.T.); -#26371=ORIENTED_EDGE('',*,*,#26370,.T.); -#26373=ORIENTED_EDGE('',*,*,#26372,.T.); -#26375=ORIENTED_EDGE('',*,*,#26374,.T.); -#26377=ORIENTED_EDGE('',*,*,#26376,.T.); -#26379=ORIENTED_EDGE('',*,*,#26378,.T.); -#26381=ORIENTED_EDGE('',*,*,#26380,.T.); -#26382=EDGE_LOOP('',(#26363,#26365,#26367,#26369,#26371,#26373,#26375,#26377, -#26379,#26381)); -#26383=FACE_OUTER_BOUND('',#26382,.F.); -#26385=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26386=DIRECTION('',(0.E0,1.E0,0.E0)); -#26387=DIRECTION('',(1.E0,0.E0,0.E0)); -#26388=AXIS2_PLACEMENT_3D('',#26385,#26386,#26387); -#26389=PLANE('',#26388); -#26391=ORIENTED_EDGE('',*,*,#26390,.T.); -#26393=ORIENTED_EDGE('',*,*,#26392,.T.); -#26395=ORIENTED_EDGE('',*,*,#26394,.T.); -#26397=ORIENTED_EDGE('',*,*,#26396,.T.); -#26399=ORIENTED_EDGE('',*,*,#26398,.T.); -#26401=ORIENTED_EDGE('',*,*,#26400,.T.); -#26403=ORIENTED_EDGE('',*,*,#26402,.T.); -#26405=ORIENTED_EDGE('',*,*,#26404,.T.); -#26407=ORIENTED_EDGE('',*,*,#26406,.T.); -#26409=ORIENTED_EDGE('',*,*,#26408,.T.); -#26411=ORIENTED_EDGE('',*,*,#26410,.T.); -#26413=ORIENTED_EDGE('',*,*,#26412,.T.); -#26415=ORIENTED_EDGE('',*,*,#26414,.T.); -#26417=ORIENTED_EDGE('',*,*,#26416,.T.); -#26419=ORIENTED_EDGE('',*,*,#26418,.T.); -#26421=ORIENTED_EDGE('',*,*,#26420,.T.); -#26422=EDGE_LOOP('',(#26391,#26393,#26395,#26397,#26399,#26401,#26403,#26405, -#26407,#26409,#26411,#26413,#26415,#26417,#26419,#26421)); -#26423=FACE_OUTER_BOUND('',#26422,.F.); -#26425=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26426=DIRECTION('',(0.E0,1.E0,0.E0)); -#26427=DIRECTION('',(1.E0,0.E0,0.E0)); -#26428=AXIS2_PLACEMENT_3D('',#26425,#26426,#26427); -#26429=PLANE('',#26428); -#26431=ORIENTED_EDGE('',*,*,#26430,.T.); -#26433=ORIENTED_EDGE('',*,*,#26432,.T.); -#26435=ORIENTED_EDGE('',*,*,#26434,.T.); -#26437=ORIENTED_EDGE('',*,*,#26436,.T.); -#26439=ORIENTED_EDGE('',*,*,#26438,.T.); -#26441=ORIENTED_EDGE('',*,*,#26440,.T.); -#26443=ORIENTED_EDGE('',*,*,#26442,.T.); -#26445=ORIENTED_EDGE('',*,*,#26444,.T.); -#26447=ORIENTED_EDGE('',*,*,#26446,.T.); -#26449=ORIENTED_EDGE('',*,*,#26448,.T.); -#26451=ORIENTED_EDGE('',*,*,#26450,.T.); -#26453=ORIENTED_EDGE('',*,*,#26452,.T.); -#26455=ORIENTED_EDGE('',*,*,#26454,.T.); -#26457=ORIENTED_EDGE('',*,*,#26456,.T.); -#26459=ORIENTED_EDGE('',*,*,#26458,.T.); -#26461=ORIENTED_EDGE('',*,*,#26460,.T.); -#26462=EDGE_LOOP('',(#26431,#26433,#26435,#26437,#26439,#26441,#26443,#26445, -#26447,#26449,#26451,#26453,#26455,#26457,#26459,#26461)); -#26463=FACE_OUTER_BOUND('',#26462,.F.); -#26465=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26466=DIRECTION('',(0.E0,1.E0,0.E0)); -#26467=DIRECTION('',(1.E0,0.E0,0.E0)); -#26468=AXIS2_PLACEMENT_3D('',#26465,#26466,#26467); -#26469=PLANE('',#26468); -#26471=ORIENTED_EDGE('',*,*,#26470,.T.); -#26473=ORIENTED_EDGE('',*,*,#26472,.T.); -#26475=ORIENTED_EDGE('',*,*,#26474,.T.); -#26477=ORIENTED_EDGE('',*,*,#26476,.T.); -#26479=ORIENTED_EDGE('',*,*,#26478,.T.); -#26481=ORIENTED_EDGE('',*,*,#26480,.T.); -#26483=ORIENTED_EDGE('',*,*,#26482,.T.); -#26485=ORIENTED_EDGE('',*,*,#26484,.T.); -#26487=ORIENTED_EDGE('',*,*,#26486,.T.); -#26489=ORIENTED_EDGE('',*,*,#26488,.T.); -#26491=ORIENTED_EDGE('',*,*,#26490,.T.); -#26493=ORIENTED_EDGE('',*,*,#26492,.T.); -#26494=EDGE_LOOP('',(#26471,#26473,#26475,#26477,#26479,#26481,#26483,#26485, -#26487,#26489,#26491,#26493)); -#26495=FACE_OUTER_BOUND('',#26494,.F.); -#26497=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26498=DIRECTION('',(0.E0,1.E0,0.E0)); -#26499=DIRECTION('',(1.E0,0.E0,0.E0)); -#26500=AXIS2_PLACEMENT_3D('',#26497,#26498,#26499); -#26501=PLANE('',#26500); -#26503=ORIENTED_EDGE('',*,*,#26502,.T.); -#26505=ORIENTED_EDGE('',*,*,#26504,.T.); -#26507=ORIENTED_EDGE('',*,*,#26506,.T.); -#26509=ORIENTED_EDGE('',*,*,#26508,.T.); -#26511=ORIENTED_EDGE('',*,*,#26510,.T.); -#26513=ORIENTED_EDGE('',*,*,#26512,.T.); -#26515=ORIENTED_EDGE('',*,*,#26514,.T.); -#26517=ORIENTED_EDGE('',*,*,#26516,.T.); -#26519=ORIENTED_EDGE('',*,*,#26518,.T.); -#26521=ORIENTED_EDGE('',*,*,#26520,.T.); -#26523=ORIENTED_EDGE('',*,*,#26522,.T.); -#26525=ORIENTED_EDGE('',*,*,#26524,.T.); -#26527=ORIENTED_EDGE('',*,*,#26526,.T.); -#26529=ORIENTED_EDGE('',*,*,#26528,.T.); -#26531=ORIENTED_EDGE('',*,*,#26530,.T.); -#26533=ORIENTED_EDGE('',*,*,#26532,.T.); -#26534=EDGE_LOOP('',(#26503,#26505,#26507,#26509,#26511,#26513,#26515,#26517, -#26519,#26521,#26523,#26525,#26527,#26529,#26531,#26533)); -#26535=FACE_OUTER_BOUND('',#26534,.F.); -#26537=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26538=DIRECTION('',(0.E0,1.E0,0.E0)); -#26539=DIRECTION('',(1.E0,0.E0,0.E0)); -#26540=AXIS2_PLACEMENT_3D('',#26537,#26538,#26539); -#26541=PLANE('',#26540); -#26543=ORIENTED_EDGE('',*,*,#26542,.T.); -#26545=ORIENTED_EDGE('',*,*,#26544,.T.); -#26547=ORIENTED_EDGE('',*,*,#26546,.T.); -#26549=ORIENTED_EDGE('',*,*,#26548,.T.); -#26551=ORIENTED_EDGE('',*,*,#26550,.T.); -#26553=ORIENTED_EDGE('',*,*,#26552,.T.); -#26555=ORIENTED_EDGE('',*,*,#26554,.T.); -#26557=ORIENTED_EDGE('',*,*,#26556,.T.); -#26559=ORIENTED_EDGE('',*,*,#26558,.T.); -#26561=ORIENTED_EDGE('',*,*,#26560,.T.); -#26563=ORIENTED_EDGE('',*,*,#26562,.T.); -#26565=ORIENTED_EDGE('',*,*,#26564,.T.); -#26567=ORIENTED_EDGE('',*,*,#26566,.T.); -#26569=ORIENTED_EDGE('',*,*,#26568,.T.); -#26571=ORIENTED_EDGE('',*,*,#26570,.T.); -#26573=ORIENTED_EDGE('',*,*,#26572,.T.); -#26574=EDGE_LOOP('',(#26543,#26545,#26547,#26549,#26551,#26553,#26555,#26557, -#26559,#26561,#26563,#26565,#26567,#26569,#26571,#26573)); -#26575=FACE_OUTER_BOUND('',#26574,.F.); -#26577=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26578=DIRECTION('',(0.E0,1.E0,0.E0)); -#26579=DIRECTION('',(1.E0,0.E0,0.E0)); -#26580=AXIS2_PLACEMENT_3D('',#26577,#26578,#26579); -#26581=PLANE('',#26580); -#26583=ORIENTED_EDGE('',*,*,#26582,.T.); -#26585=ORIENTED_EDGE('',*,*,#26584,.T.); -#26587=ORIENTED_EDGE('',*,*,#26586,.T.); -#26589=ORIENTED_EDGE('',*,*,#26588,.T.); -#26591=ORIENTED_EDGE('',*,*,#26590,.T.); -#26593=ORIENTED_EDGE('',*,*,#26592,.T.); -#26595=ORIENTED_EDGE('',*,*,#26594,.T.); -#26597=ORIENTED_EDGE('',*,*,#26596,.T.); -#26599=ORIENTED_EDGE('',*,*,#26598,.T.); -#26601=ORIENTED_EDGE('',*,*,#26600,.T.); -#26602=EDGE_LOOP('',(#26583,#26585,#26587,#26589,#26591,#26593,#26595,#26597, -#26599,#26601)); -#26603=FACE_OUTER_BOUND('',#26602,.F.); -#26605=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26606=DIRECTION('',(0.E0,1.E0,0.E0)); -#26607=DIRECTION('',(1.E0,0.E0,0.E0)); -#26608=AXIS2_PLACEMENT_3D('',#26605,#26606,#26607); -#26609=PLANE('',#26608); -#26611=ORIENTED_EDGE('',*,*,#26610,.T.); -#26613=ORIENTED_EDGE('',*,*,#26612,.T.); -#26615=ORIENTED_EDGE('',*,*,#26614,.T.); -#26617=ORIENTED_EDGE('',*,*,#26616,.T.); -#26619=ORIENTED_EDGE('',*,*,#26618,.T.); -#26621=ORIENTED_EDGE('',*,*,#26620,.T.); -#26623=ORIENTED_EDGE('',*,*,#26622,.T.); -#26625=ORIENTED_EDGE('',*,*,#26624,.T.); -#26627=ORIENTED_EDGE('',*,*,#26626,.T.); -#26629=ORIENTED_EDGE('',*,*,#26628,.T.); -#26630=EDGE_LOOP('',(#26611,#26613,#26615,#26617,#26619,#26621,#26623,#26625, -#26627,#26629)); -#26631=FACE_OUTER_BOUND('',#26630,.F.); -#26633=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26634=DIRECTION('',(0.E0,1.E0,0.E0)); -#26635=DIRECTION('',(1.E0,0.E0,0.E0)); -#26636=AXIS2_PLACEMENT_3D('',#26633,#26634,#26635); -#26637=PLANE('',#26636); -#26639=ORIENTED_EDGE('',*,*,#26638,.T.); -#26641=ORIENTED_EDGE('',*,*,#26640,.T.); -#26643=ORIENTED_EDGE('',*,*,#26642,.T.); -#26645=ORIENTED_EDGE('',*,*,#26644,.T.); -#26647=ORIENTED_EDGE('',*,*,#26646,.T.); -#26649=ORIENTED_EDGE('',*,*,#26648,.T.); -#26651=ORIENTED_EDGE('',*,*,#26650,.T.); -#26653=ORIENTED_EDGE('',*,*,#26652,.T.); -#26655=ORIENTED_EDGE('',*,*,#26654,.T.); -#26657=ORIENTED_EDGE('',*,*,#26656,.T.); -#26659=ORIENTED_EDGE('',*,*,#26658,.T.); -#26661=ORIENTED_EDGE('',*,*,#26660,.T.); -#26663=ORIENTED_EDGE('',*,*,#26662,.T.); -#26665=ORIENTED_EDGE('',*,*,#26664,.T.); -#26667=ORIENTED_EDGE('',*,*,#26666,.T.); -#26669=ORIENTED_EDGE('',*,*,#26668,.T.); -#26670=EDGE_LOOP('',(#26639,#26641,#26643,#26645,#26647,#26649,#26651,#26653, -#26655,#26657,#26659,#26661,#26663,#26665,#26667,#26669)); -#26671=FACE_OUTER_BOUND('',#26670,.F.); -#26673=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26674=DIRECTION('',(0.E0,1.E0,0.E0)); -#26675=DIRECTION('',(1.E0,0.E0,0.E0)); -#26676=AXIS2_PLACEMENT_3D('',#26673,#26674,#26675); -#26677=PLANE('',#26676); -#26679=ORIENTED_EDGE('',*,*,#26678,.T.); -#26681=ORIENTED_EDGE('',*,*,#26680,.T.); -#26683=ORIENTED_EDGE('',*,*,#26682,.T.); -#26685=ORIENTED_EDGE('',*,*,#26684,.T.); -#26687=ORIENTED_EDGE('',*,*,#26686,.T.); -#26689=ORIENTED_EDGE('',*,*,#26688,.T.); -#26691=ORIENTED_EDGE('',*,*,#26690,.T.); -#26693=ORIENTED_EDGE('',*,*,#26692,.T.); -#26695=ORIENTED_EDGE('',*,*,#26694,.T.); -#26697=ORIENTED_EDGE('',*,*,#26696,.T.); -#26699=ORIENTED_EDGE('',*,*,#26698,.T.); -#26701=ORIENTED_EDGE('',*,*,#26700,.T.); -#26703=ORIENTED_EDGE('',*,*,#26702,.T.); -#26705=ORIENTED_EDGE('',*,*,#26704,.T.); -#26707=ORIENTED_EDGE('',*,*,#26706,.T.); -#26709=ORIENTED_EDGE('',*,*,#26708,.T.); -#26710=EDGE_LOOP('',(#26679,#26681,#26683,#26685,#26687,#26689,#26691,#26693, -#26695,#26697,#26699,#26701,#26703,#26705,#26707,#26709)); -#26711=FACE_OUTER_BOUND('',#26710,.F.); -#26713=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26714=DIRECTION('',(0.E0,1.E0,0.E0)); -#26715=DIRECTION('',(1.E0,0.E0,0.E0)); -#26716=AXIS2_PLACEMENT_3D('',#26713,#26714,#26715); -#26717=PLANE('',#26716); -#26719=ORIENTED_EDGE('',*,*,#26718,.T.); -#26721=ORIENTED_EDGE('',*,*,#26720,.T.); -#26723=ORIENTED_EDGE('',*,*,#26722,.T.); -#26725=ORIENTED_EDGE('',*,*,#26724,.T.); -#26727=ORIENTED_EDGE('',*,*,#26726,.T.); -#26729=ORIENTED_EDGE('',*,*,#26728,.T.); -#26731=ORIENTED_EDGE('',*,*,#26730,.T.); -#26733=ORIENTED_EDGE('',*,*,#26732,.T.); -#26735=ORIENTED_EDGE('',*,*,#26734,.T.); -#26737=ORIENTED_EDGE('',*,*,#26736,.T.); -#26739=ORIENTED_EDGE('',*,*,#26738,.T.); -#26741=ORIENTED_EDGE('',*,*,#26740,.T.); -#26742=EDGE_LOOP('',(#26719,#26721,#26723,#26725,#26727,#26729,#26731,#26733, -#26735,#26737,#26739,#26741)); -#26743=FACE_OUTER_BOUND('',#26742,.F.); -#26745=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26746=DIRECTION('',(0.E0,1.E0,0.E0)); -#26747=DIRECTION('',(1.E0,0.E0,0.E0)); -#26748=AXIS2_PLACEMENT_3D('',#26745,#26746,#26747); -#26749=PLANE('',#26748); -#26751=ORIENTED_EDGE('',*,*,#26750,.T.); -#26753=ORIENTED_EDGE('',*,*,#26752,.T.); -#26755=ORIENTED_EDGE('',*,*,#26754,.T.); -#26756=EDGE_LOOP('',(#26751,#26753,#26755)); -#26757=FACE_OUTER_BOUND('',#26756,.F.); -#26759=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26760=DIRECTION('',(0.E0,1.E0,0.E0)); -#26761=DIRECTION('',(1.E0,0.E0,0.E0)); -#26762=AXIS2_PLACEMENT_3D('',#26759,#26760,#26761); -#26763=PLANE('',#26762); -#26765=ORIENTED_EDGE('',*,*,#26764,.T.); -#26767=ORIENTED_EDGE('',*,*,#26766,.T.); -#26769=ORIENTED_EDGE('',*,*,#26768,.T.); -#26771=ORIENTED_EDGE('',*,*,#26770,.T.); -#26773=ORIENTED_EDGE('',*,*,#26772,.T.); -#26775=ORIENTED_EDGE('',*,*,#26774,.T.); -#26777=ORIENTED_EDGE('',*,*,#26776,.T.); -#26779=ORIENTED_EDGE('',*,*,#26778,.T.); -#26781=ORIENTED_EDGE('',*,*,#26780,.T.); -#26783=ORIENTED_EDGE('',*,*,#26782,.T.); -#26785=ORIENTED_EDGE('',*,*,#26784,.T.); -#26787=ORIENTED_EDGE('',*,*,#26786,.T.); -#26789=ORIENTED_EDGE('',*,*,#26788,.T.); -#26791=ORIENTED_EDGE('',*,*,#26790,.T.); -#26793=ORIENTED_EDGE('',*,*,#26792,.T.); -#26795=ORIENTED_EDGE('',*,*,#26794,.T.); -#26797=ORIENTED_EDGE('',*,*,#26796,.T.); -#26799=ORIENTED_EDGE('',*,*,#26798,.T.); -#26800=EDGE_LOOP('',(#26765,#26767,#26769,#26771,#26773,#26775,#26777,#26779, -#26781,#26783,#26785,#26787,#26789,#26791,#26793,#26795,#26797,#26799)); -#26801=FACE_OUTER_BOUND('',#26800,.F.); -#26803=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26804=DIRECTION('',(0.E0,1.E0,0.E0)); -#26805=DIRECTION('',(1.E0,0.E0,0.E0)); -#26806=AXIS2_PLACEMENT_3D('',#26803,#26804,#26805); -#26807=PLANE('',#26806); -#26809=ORIENTED_EDGE('',*,*,#26808,.T.); -#26811=ORIENTED_EDGE('',*,*,#26810,.T.); -#26813=ORIENTED_EDGE('',*,*,#26812,.T.); -#26815=ORIENTED_EDGE('',*,*,#26814,.T.); -#26817=ORIENTED_EDGE('',*,*,#26816,.T.); -#26819=ORIENTED_EDGE('',*,*,#26818,.T.); -#26821=ORIENTED_EDGE('',*,*,#26820,.T.); -#26823=ORIENTED_EDGE('',*,*,#26822,.T.); -#26825=ORIENTED_EDGE('',*,*,#26824,.T.); -#26827=ORIENTED_EDGE('',*,*,#26826,.T.); -#26829=ORIENTED_EDGE('',*,*,#26828,.T.); -#26831=ORIENTED_EDGE('',*,*,#26830,.T.); -#26833=ORIENTED_EDGE('',*,*,#26832,.T.); -#26835=ORIENTED_EDGE('',*,*,#26834,.T.); -#26837=ORIENTED_EDGE('',*,*,#26836,.T.); -#26839=ORIENTED_EDGE('',*,*,#26838,.T.); -#26841=ORIENTED_EDGE('',*,*,#26840,.T.); -#26843=ORIENTED_EDGE('',*,*,#26842,.T.); -#26844=EDGE_LOOP('',(#26809,#26811,#26813,#26815,#26817,#26819,#26821,#26823, -#26825,#26827,#26829,#26831,#26833,#26835,#26837,#26839,#26841,#26843)); -#26845=FACE_OUTER_BOUND('',#26844,.F.); -#26847=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26848=DIRECTION('',(0.E0,1.E0,0.E0)); -#26849=DIRECTION('',(1.E0,0.E0,0.E0)); -#26850=AXIS2_PLACEMENT_3D('',#26847,#26848,#26849); -#26851=PLANE('',#26850); -#26853=ORIENTED_EDGE('',*,*,#26852,.T.); -#26855=ORIENTED_EDGE('',*,*,#26854,.T.); -#26857=ORIENTED_EDGE('',*,*,#26856,.T.); -#26858=EDGE_LOOP('',(#26853,#26855,#26857)); -#26859=FACE_OUTER_BOUND('',#26858,.F.); -#26861=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26862=DIRECTION('',(0.E0,1.E0,0.E0)); -#26863=DIRECTION('',(1.E0,0.E0,0.E0)); -#26864=AXIS2_PLACEMENT_3D('',#26861,#26862,#26863); -#26865=PLANE('',#26864); -#26867=ORIENTED_EDGE('',*,*,#26866,.T.); -#26869=ORIENTED_EDGE('',*,*,#26868,.T.); -#26871=ORIENTED_EDGE('',*,*,#26870,.T.); -#26873=ORIENTED_EDGE('',*,*,#26872,.T.); -#26875=ORIENTED_EDGE('',*,*,#26874,.T.); -#26877=ORIENTED_EDGE('',*,*,#26876,.T.); -#26879=ORIENTED_EDGE('',*,*,#26878,.T.); -#26881=ORIENTED_EDGE('',*,*,#26880,.T.); -#26883=ORIENTED_EDGE('',*,*,#26882,.T.); -#26885=ORIENTED_EDGE('',*,*,#26884,.T.); -#26886=EDGE_LOOP('',(#26867,#26869,#26871,#26873,#26875,#26877,#26879,#26881, -#26883,#26885)); -#26887=FACE_OUTER_BOUND('',#26886,.F.); -#26889=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26890=DIRECTION('',(0.E0,1.E0,0.E0)); -#26891=DIRECTION('',(1.E0,0.E0,0.E0)); -#26892=AXIS2_PLACEMENT_3D('',#26889,#26890,#26891); -#26893=PLANE('',#26892); -#26895=ORIENTED_EDGE('',*,*,#26894,.T.); -#26897=ORIENTED_EDGE('',*,*,#26896,.T.); -#26899=ORIENTED_EDGE('',*,*,#26898,.T.); -#26901=ORIENTED_EDGE('',*,*,#26900,.T.); -#26903=ORIENTED_EDGE('',*,*,#26902,.T.); -#26905=ORIENTED_EDGE('',*,*,#26904,.T.); -#26907=ORIENTED_EDGE('',*,*,#26906,.T.); -#26909=ORIENTED_EDGE('',*,*,#26908,.T.); -#26911=ORIENTED_EDGE('',*,*,#26910,.T.); -#26913=ORIENTED_EDGE('',*,*,#26912,.T.); -#26914=EDGE_LOOP('',(#26895,#26897,#26899,#26901,#26903,#26905,#26907,#26909, -#26911,#26913)); -#26915=FACE_OUTER_BOUND('',#26914,.F.); -#26917=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26918=DIRECTION('',(0.E0,1.E0,0.E0)); -#26919=DIRECTION('',(1.E0,0.E0,0.E0)); -#26920=AXIS2_PLACEMENT_3D('',#26917,#26918,#26919); -#26921=PLANE('',#26920); -#26923=ORIENTED_EDGE('',*,*,#26922,.T.); -#26925=ORIENTED_EDGE('',*,*,#26924,.T.); -#26927=ORIENTED_EDGE('',*,*,#26926,.T.); -#26929=ORIENTED_EDGE('',*,*,#26928,.T.); -#26931=ORIENTED_EDGE('',*,*,#26930,.T.); -#26933=ORIENTED_EDGE('',*,*,#26932,.T.); -#26935=ORIENTED_EDGE('',*,*,#26934,.T.); -#26937=ORIENTED_EDGE('',*,*,#26936,.T.); -#26939=ORIENTED_EDGE('',*,*,#26938,.T.); -#26941=ORIENTED_EDGE('',*,*,#26940,.T.); -#26943=ORIENTED_EDGE('',*,*,#26942,.T.); -#26945=ORIENTED_EDGE('',*,*,#26944,.T.); -#26947=ORIENTED_EDGE('',*,*,#26946,.T.); -#26949=ORIENTED_EDGE('',*,*,#26948,.T.); -#26951=ORIENTED_EDGE('',*,*,#26950,.T.); -#26953=ORIENTED_EDGE('',*,*,#26952,.T.); -#26954=EDGE_LOOP('',(#26923,#26925,#26927,#26929,#26931,#26933,#26935,#26937, -#26939,#26941,#26943,#26945,#26947,#26949,#26951,#26953)); -#26955=FACE_OUTER_BOUND('',#26954,.F.); -#26957=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26958=DIRECTION('',(0.E0,1.E0,0.E0)); -#26959=DIRECTION('',(1.E0,0.E0,0.E0)); -#26960=AXIS2_PLACEMENT_3D('',#26957,#26958,#26959); -#26961=PLANE('',#26960); -#26963=ORIENTED_EDGE('',*,*,#26962,.T.); -#26965=ORIENTED_EDGE('',*,*,#26964,.T.); -#26967=ORIENTED_EDGE('',*,*,#26966,.T.); -#26969=ORIENTED_EDGE('',*,*,#26968,.T.); -#26971=ORIENTED_EDGE('',*,*,#26970,.T.); -#26973=ORIENTED_EDGE('',*,*,#26972,.T.); -#26975=ORIENTED_EDGE('',*,*,#26974,.T.); -#26977=ORIENTED_EDGE('',*,*,#26976,.T.); -#26979=ORIENTED_EDGE('',*,*,#26978,.T.); -#26981=ORIENTED_EDGE('',*,*,#26980,.T.); -#26983=ORIENTED_EDGE('',*,*,#26982,.T.); -#26985=ORIENTED_EDGE('',*,*,#26984,.T.); -#26987=ORIENTED_EDGE('',*,*,#26986,.T.); -#26989=ORIENTED_EDGE('',*,*,#26988,.T.); -#26991=ORIENTED_EDGE('',*,*,#26990,.T.); -#26993=ORIENTED_EDGE('',*,*,#26992,.T.); -#26994=EDGE_LOOP('',(#26963,#26965,#26967,#26969,#26971,#26973,#26975,#26977, -#26979,#26981,#26983,#26985,#26987,#26989,#26991,#26993)); -#26995=FACE_OUTER_BOUND('',#26994,.F.); -#26997=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#26998=DIRECTION('',(0.E0,1.E0,0.E0)); -#26999=DIRECTION('',(1.E0,0.E0,0.E0)); -#27000=AXIS2_PLACEMENT_3D('',#26997,#26998,#26999); -#27001=PLANE('',#27000); -#27003=ORIENTED_EDGE('',*,*,#27002,.T.); -#27005=ORIENTED_EDGE('',*,*,#27004,.T.); -#27007=ORIENTED_EDGE('',*,*,#27006,.T.); -#27008=EDGE_LOOP('',(#27003,#27005,#27007)); -#27009=FACE_OUTER_BOUND('',#27008,.F.); -#27011=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#27012=DIRECTION('',(0.E0,1.E0,0.E0)); -#27013=DIRECTION('',(1.E0,0.E0,0.E0)); -#27014=AXIS2_PLACEMENT_3D('',#27011,#27012,#27013); -#27015=PLANE('',#27014); -#27017=ORIENTED_EDGE('',*,*,#27016,.F.); -#27019=ORIENTED_EDGE('',*,*,#27018,.T.); -#27021=ORIENTED_EDGE('',*,*,#27020,.F.); -#27022=EDGE_LOOP('',(#27017,#27019,#27021)); -#27023=FACE_OUTER_BOUND('',#27022,.F.); -#27025=CARTESIAN_POINT('',(0.E0,1.55E0,0.E0)); -#27026=DIRECTION('',(0.E0,1.E0,0.E0)); -#27027=DIRECTION('',(1.E0,0.E0,0.E0)); -#27028=AXIS2_PLACEMENT_3D('',#27025,#27026,#27027); -#27029=PLANE('',#27028); -#27031=ORIENTED_EDGE('',*,*,#27030,.T.); -#27033=ORIENTED_EDGE('',*,*,#27032,.F.); -#27035=ORIENTED_EDGE('',*,*,#27034,.T.); -#27037=ORIENTED_EDGE('',*,*,#27036,.F.); -#27039=ORIENTED_EDGE('',*,*,#27038,.T.); -#27041=ORIENTED_EDGE('',*,*,#27040,.F.); -#27043=ORIENTED_EDGE('',*,*,#27042,.T.); -#27045=ORIENTED_EDGE('',*,*,#27044,.F.); -#27047=ORIENTED_EDGE('',*,*,#27046,.T.); -#27049=ORIENTED_EDGE('',*,*,#27048,.F.); -#27051=ORIENTED_EDGE('',*,*,#27050,.T.); -#27053=ORIENTED_EDGE('',*,*,#27052,.F.); -#27054=EDGE_LOOP('',(#27031,#27033,#27035,#27037,#27039,#27041,#27043,#27045, -#27047,#27049,#27051,#27053)); -#27055=FACE_OUTER_BOUND('',#27054,.F.); -#27057=CARTESIAN_POINT('',(-5.4E0,3.E-1,1.342E1)); -#27058=DIRECTION('',(0.E0,0.E0,1.E0)); -#27059=DIRECTION('',(1.E0,0.E0,0.E0)); -#27060=AXIS2_PLACEMENT_3D('',#27057,#27058,#27059); -#27061=PLANE('',#27060); -#27062=ORIENTED_EDGE('',*,*,#24422,.F.); -#27064=ORIENTED_EDGE('',*,*,#27063,.F.); -#27065=ORIENTED_EDGE('',*,*,#24330,.F.); -#27066=ORIENTED_EDGE('',*,*,#24481,.T.); -#27067=ORIENTED_EDGE('',*,*,#24576,.F.); -#27068=ORIENTED_EDGE('',*,*,#24376,.F.); -#27069=ORIENTED_EDGE('',*,*,#24354,.F.); -#27071=ORIENTED_EDGE('',*,*,#27070,.T.); -#27072=EDGE_LOOP('',(#27062,#27064,#27065,#27066,#27067,#27068,#27069,#27071)); -#27073=FACE_OUTER_BOUND('',#27072,.F.); -#27075=CARTESIAN_POINT('',(-4.9E-1,3.E-1,1.327E1)); -#27076=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27077=DIRECTION('',(0.E0,0.E0,1.E0)); -#27078=AXIS2_PLACEMENT_3D('',#27075,#27076,#27077); -#27079=PLANE('',#27078); -#27080=ORIENTED_EDGE('',*,*,#27063,.T.); -#27081=ORIENTED_EDGE('',*,*,#24420,.F.); -#27083=ORIENTED_EDGE('',*,*,#27082,.F.); -#27084=ORIENTED_EDGE('',*,*,#24332,.T.); -#27085=EDGE_LOOP('',(#27080,#27081,#27083,#27084)); -#27086=FACE_OUTER_BOUND('',#27085,.F.); -#27088=CARTESIAN_POINT('',(-5.25E0,3.E-1,1.327E1)); -#27089=DIRECTION('',(0.E0,0.E0,1.E0)); -#27090=DIRECTION('',(1.E0,0.E0,0.E0)); -#27091=AXIS2_PLACEMENT_3D('',#27088,#27089,#27090); -#27092=PLANE('',#27091); -#27093=ORIENTED_EDGE('',*,*,#24334,.T.); -#27094=ORIENTED_EDGE('',*,*,#27082,.T.); -#27095=ORIENTED_EDGE('',*,*,#24418,.F.); -#27097=ORIENTED_EDGE('',*,*,#27096,.F.); -#27098=EDGE_LOOP('',(#27093,#27094,#27095,#27097)); -#27099=FACE_OUTER_BOUND('',#27098,.F.); -#27101=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.757618014356E0)); -#27102=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27103=DIRECTION('',(0.E0,0.E0,1.E0)); -#27104=AXIS2_PLACEMENT_3D('',#27101,#27102,#27103); -#27105=PLANE('',#27104); -#27106=ORIENTED_EDGE('',*,*,#24336,.T.); -#27107=ORIENTED_EDGE('',*,*,#27096,.T.); -#27108=ORIENTED_EDGE('',*,*,#24416,.F.); -#27110=ORIENTED_EDGE('',*,*,#27109,.F.); -#27111=EDGE_LOOP('',(#27106,#27107,#27108,#27110)); -#27112=FACE_OUTER_BOUND('',#27111,.F.); -#27114=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.757618014356E0)); -#27115=DIRECTION('',(0.E0,0.E0,1.E0)); -#27116=DIRECTION('',(1.E0,0.E0,0.E0)); -#27117=AXIS2_PLACEMENT_3D('',#27114,#27115,#27116); -#27118=PLANE('',#27117); -#27119=ORIENTED_EDGE('',*,*,#24484,.F.); -#27120=ORIENTED_EDGE('',*,*,#24338,.T.); -#27121=ORIENTED_EDGE('',*,*,#27109,.T.); -#27122=ORIENTED_EDGE('',*,*,#24414,.F.); -#27123=EDGE_LOOP('',(#27119,#27120,#27121,#27122)); -#27124=FACE_OUTER_BOUND('',#27123,.F.); -#27126=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.342E1)); -#27127=DIRECTION('',(1.E0,0.E0,0.E0)); -#27128=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27129=AXIS2_PLACEMENT_3D('',#27126,#27127,#27128); -#27130=PLANE('',#27129); -#27131=ORIENTED_EDGE('',*,*,#27070,.F.); -#27132=ORIENTED_EDGE('',*,*,#24352,.T.); -#27134=ORIENTED_EDGE('',*,*,#27133,.T.); -#27135=ORIENTED_EDGE('',*,*,#24424,.F.); -#27136=EDGE_LOOP('',(#27131,#27132,#27134,#27135)); -#27137=FACE_OUTER_BOUND('',#27136,.F.); -#27139=CARTESIAN_POINT('',(5.1E-1,3.E-1,1.327E1)); -#27140=DIRECTION('',(0.E0,0.E0,1.E0)); -#27141=DIRECTION('',(1.E0,0.E0,0.E0)); -#27142=AXIS2_PLACEMENT_3D('',#27139,#27140,#27141); -#27143=PLANE('',#27142); -#27144=ORIENTED_EDGE('',*,*,#24350,.T.); -#27146=ORIENTED_EDGE('',*,*,#27145,.T.); -#27147=ORIENTED_EDGE('',*,*,#24426,.F.); -#27148=ORIENTED_EDGE('',*,*,#27133,.F.); -#27149=EDGE_LOOP('',(#27144,#27146,#27147,#27148)); -#27150=FACE_OUTER_BOUND('',#27149,.F.); -#27152=CARTESIAN_POINT('',(6.65E0,3.E-1,1.327E1)); -#27153=DIRECTION('',(1.E0,0.E0,0.E0)); -#27154=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27155=AXIS2_PLACEMENT_3D('',#27152,#27153,#27154); -#27156=PLANE('',#27155); -#27157=ORIENTED_EDGE('',*,*,#24348,.T.); -#27159=ORIENTED_EDGE('',*,*,#27158,.T.); -#27160=ORIENTED_EDGE('',*,*,#24428,.F.); -#27161=ORIENTED_EDGE('',*,*,#27145,.F.); -#27162=EDGE_LOOP('',(#27157,#27159,#27160,#27161)); -#27163=FACE_OUTER_BOUND('',#27162,.F.); -#27165=CARTESIAN_POINT('',(6.65E0,3.E-1,8.039068448582E0)); -#27166=DIRECTION('',(0.E0,0.E0,1.E0)); -#27167=DIRECTION('',(1.E0,0.E0,0.E0)); -#27168=AXIS2_PLACEMENT_3D('',#27165,#27166,#27167); -#27169=PLANE('',#27168); -#27170=ORIENTED_EDGE('',*,*,#24373,.T.); -#27171=ORIENTED_EDGE('',*,*,#24430,.F.); -#27172=ORIENTED_EDGE('',*,*,#27158,.F.); -#27173=ORIENTED_EDGE('',*,*,#24346,.T.); -#27174=EDGE_LOOP('',(#27170,#27171,#27172,#27173)); -#27175=FACE_OUTER_BOUND('',#27174,.F.); -#27177=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,8.126726183650E0)); -#27178=DIRECTION('',(7.979696418218E-1,0.E0,-6.026976445372E-1)); -#27179=DIRECTION('',(-6.026976445372E-1,0.E0,-7.979696418218E-1)); -#27180=AXIS2_PLACEMENT_3D('',#27177,#27178,#27179); -#27181=PLANE('',#27180); -#27182=ORIENTED_EDGE('',*,*,#24580,.F.); -#27184=ORIENTED_EDGE('',*,*,#27183,.T.); -#27186=ORIENTED_EDGE('',*,*,#27185,.T.); -#27188=ORIENTED_EDGE('',*,*,#27187,.F.); -#27189=EDGE_LOOP('',(#27182,#27184,#27186,#27188)); -#27190=FACE_OUTER_BOUND('',#27189,.F.); -#27192=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,8.070385908836E0)); -#27193=DIRECTION('',(-7.979696418218E-1,0.E0,-6.026976445372E-1)); -#27194=DIRECTION('',(-6.026976445372E-1,0.E0,7.979696418218E-1)); -#27195=AXIS2_PLACEMENT_3D('',#27192,#27193,#27194); -#27196=PLANE('',#27195); -#27197=ORIENTED_EDGE('',*,*,#24616,.F.); -#27199=ORIENTED_EDGE('',*,*,#27198,.T.); -#27201=ORIENTED_EDGE('',*,*,#27200,.T.); -#27202=ORIENTED_EDGE('',*,*,#27183,.F.); -#27203=EDGE_LOOP('',(#27197,#27199,#27201,#27202)); -#27204=FACE_OUTER_BOUND('',#27203,.F.); -#27206=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,7.985875536912E0)); -#27207=DIRECTION('',(-4.447028582079E-1,0.E0,-8.956781608936E-1)); -#27208=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#27209=AXIS2_PLACEMENT_3D('',#27206,#27207,#27208); -#27210=PLANE('',#27209); -#27211=ORIENTED_EDGE('',*,*,#24614,.F.); -#27213=ORIENTED_EDGE('',*,*,#27212,.T.); -#27215=ORIENTED_EDGE('',*,*,#27214,.T.); -#27216=ORIENTED_EDGE('',*,*,#27198,.F.); -#27217=EDGE_LOOP('',(#27211,#27213,#27215,#27216)); -#27218=FACE_OUTER_BOUND('',#27217,.F.); -#27220=CARTESIAN_POINT('',(1.319148957729E0,1.55E0,7.957705439802E0)); -#27221=DIRECTION('',(-2.154817752655E-1,0.E0,-9.765078619901E-1)); -#27222=DIRECTION('',(-9.765078619901E-1,0.E0,2.154817752655E-1)); -#27223=AXIS2_PLACEMENT_3D('',#27220,#27221,#27222); -#27224=PLANE('',#27223); -#27225=ORIENTED_EDGE('',*,*,#24612,.F.); -#27227=ORIENTED_EDGE('',*,*,#27226,.T.); -#27229=ORIENTED_EDGE('',*,*,#27228,.T.); -#27230=ORIENTED_EDGE('',*,*,#27212,.F.); -#27231=EDGE_LOOP('',(#27225,#27227,#27229,#27230)); -#27232=FACE_OUTER_BOUND('',#27231,.F.); -#27234=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,7.957705439802E0)); -#27235=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27236=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27237=AXIS2_PLACEMENT_3D('',#27234,#27235,#27236); -#27238=PLANE('',#27237); -#27239=ORIENTED_EDGE('',*,*,#24610,.F.); -#27241=ORIENTED_EDGE('',*,*,#27240,.T.); -#27243=ORIENTED_EDGE('',*,*,#27242,.T.); -#27244=ORIENTED_EDGE('',*,*,#27226,.F.); -#27245=EDGE_LOOP('',(#27239,#27241,#27243,#27244)); -#27246=FACE_OUTER_BOUND('',#27245,.F.); -#27248=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,7.985875536912E0)); -#27249=DIRECTION('',(2.154818232343E-1,0.E0,-9.765078514050E-1)); -#27250=DIRECTION('',(-9.765078514050E-1,0.E0,-2.154818232343E-1)); -#27251=AXIS2_PLACEMENT_3D('',#27248,#27249,#27250); -#27252=PLANE('',#27251); -#27253=ORIENTED_EDGE('',*,*,#24608,.F.); -#27255=ORIENTED_EDGE('',*,*,#27254,.T.); -#27257=ORIENTED_EDGE('',*,*,#27256,.T.); -#27258=ORIENTED_EDGE('',*,*,#27240,.F.); -#27259=EDGE_LOOP('',(#27253,#27255,#27257,#27258)); -#27260=FACE_OUTER_BOUND('',#27259,.F.); -#27262=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,8.070385908836E0)); -#27263=DIRECTION('',(4.447028269758E-1,0.E0,-8.956781764003E-1)); -#27264=DIRECTION('',(-8.956781764003E-1,0.E0,-4.447028269758E-1)); -#27265=AXIS2_PLACEMENT_3D('',#27262,#27263,#27264); -#27266=PLANE('',#27265); -#27267=ORIENTED_EDGE('',*,*,#24606,.F.); -#27269=ORIENTED_EDGE('',*,*,#27268,.T.); -#27271=ORIENTED_EDGE('',*,*,#27270,.T.); -#27272=ORIENTED_EDGE('',*,*,#27254,.F.); -#27273=EDGE_LOOP('',(#27267,#27269,#27271,#27272)); -#27274=FACE_OUTER_BOUND('',#27273,.F.); -#27276=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,8.183066377870E0)); -#27277=DIRECTION('',(6.617526240224E-1,0.E0,-7.497222583060E-1)); -#27278=DIRECTION('',(-7.497222583060E-1,0.E0,-6.617526240224E-1)); -#27279=AXIS2_PLACEMENT_3D('',#27276,#27277,#27278); -#27280=PLANE('',#27279); -#27281=ORIENTED_EDGE('',*,*,#24604,.F.); -#27283=ORIENTED_EDGE('',*,*,#27282,.T.); -#27285=ORIENTED_EDGE('',*,*,#27284,.T.); -#27286=ORIENTED_EDGE('',*,*,#27268,.F.); -#27287=EDGE_LOOP('',(#27281,#27283,#27285,#27286)); -#27288=FACE_OUTER_BOUND('',#27287,.F.); -#27290=CARTESIAN_POINT('',(2.E0,1.55E0,8.323917024608E0)); -#27291=DIRECTION('',(9.572670667637E-1,0.E0,-2.892053991362E-1)); -#27292=DIRECTION('',(-2.892053991362E-1,0.E0,-9.572670667637E-1)); -#27293=AXIS2_PLACEMENT_3D('',#27290,#27291,#27292); -#27294=PLANE('',#27293); -#27295=ORIENTED_EDGE('',*,*,#24602,.F.); -#27297=ORIENTED_EDGE('',*,*,#27296,.T.); -#27299=ORIENTED_EDGE('',*,*,#27298,.T.); -#27300=ORIENTED_EDGE('',*,*,#27282,.F.); -#27301=EDGE_LOOP('',(#27295,#27297,#27299,#27300)); -#27302=FACE_OUTER_BOUND('',#27301,.F.); -#27304=CARTESIAN_POINT('',(2.E0,1.55E0,9.E0)); -#27305=DIRECTION('',(1.E0,0.E0,0.E0)); -#27306=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27307=AXIS2_PLACEMENT_3D('',#27304,#27305,#27306); -#27308=PLANE('',#27307); -#27309=ORIENTED_EDGE('',*,*,#24600,.F.); -#27311=ORIENTED_EDGE('',*,*,#27310,.T.); -#27313=ORIENTED_EDGE('',*,*,#27312,.T.); -#27314=ORIENTED_EDGE('',*,*,#27296,.F.); -#27315=EDGE_LOOP('',(#27309,#27311,#27313,#27314)); -#27316=FACE_OUTER_BOUND('',#27315,.F.); -#27318=CARTESIAN_POINT('',(0.E0,1.55E0,9.E0)); -#27319=DIRECTION('',(0.E0,0.E0,1.E0)); -#27320=DIRECTION('',(1.E0,0.E0,0.E0)); -#27321=AXIS2_PLACEMENT_3D('',#27318,#27319,#27320); -#27322=PLANE('',#27321); -#27323=ORIENTED_EDGE('',*,*,#24598,.F.); -#27325=ORIENTED_EDGE('',*,*,#27324,.T.); -#27327=ORIENTED_EDGE('',*,*,#27326,.T.); -#27328=ORIENTED_EDGE('',*,*,#27310,.F.); -#27329=EDGE_LOOP('',(#27323,#27325,#27327,#27328)); -#27330=FACE_OUTER_BOUND('',#27329,.F.); -#27332=CARTESIAN_POINT('',(0.E0,1.55E0,8.323917024608E0)); -#27333=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27334=DIRECTION('',(0.E0,0.E0,1.E0)); -#27335=AXIS2_PLACEMENT_3D('',#27332,#27333,#27334); -#27336=PLANE('',#27335); -#27337=ORIENTED_EDGE('',*,*,#24596,.F.); -#27339=ORIENTED_EDGE('',*,*,#27338,.T.); -#27341=ORIENTED_EDGE('',*,*,#27340,.T.); -#27342=ORIENTED_EDGE('',*,*,#27324,.F.); -#27343=EDGE_LOOP('',(#27337,#27339,#27341,#27342)); -#27344=FACE_OUTER_BOUND('',#27343,.F.); -#27346=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,8.183066377870E0)); -#27347=DIRECTION('',(-9.572670737730E-1,0.E0,-2.892053759356E-1)); -#27348=DIRECTION('',(-2.892053759356E-1,0.E0,9.572670737730E-1)); -#27349=AXIS2_PLACEMENT_3D('',#27346,#27347,#27348); -#27350=PLANE('',#27349); -#27351=ORIENTED_EDGE('',*,*,#24594,.F.); -#27353=ORIENTED_EDGE('',*,*,#27352,.T.); -#27355=ORIENTED_EDGE('',*,*,#27354,.T.); -#27356=ORIENTED_EDGE('',*,*,#27338,.F.); -#27357=EDGE_LOOP('',(#27351,#27353,#27355,#27356)); -#27358=FACE_OUTER_BOUND('',#27357,.F.); -#27360=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,8.070385908836E0)); -#27361=DIRECTION('',(-6.617526565854E-1,0.E0,-7.497222295638E-1)); -#27362=DIRECTION('',(-7.497222295638E-1,0.E0,6.617526565854E-1)); -#27363=AXIS2_PLACEMENT_3D('',#27360,#27361,#27362); -#27364=PLANE('',#27363); -#27365=ORIENTED_EDGE('',*,*,#24592,.F.); -#27367=ORIENTED_EDGE('',*,*,#27366,.T.); -#27369=ORIENTED_EDGE('',*,*,#27368,.T.); -#27370=ORIENTED_EDGE('',*,*,#27352,.F.); -#27371=EDGE_LOOP('',(#27365,#27367,#27369,#27370)); -#27372=FACE_OUTER_BOUND('',#27371,.F.); -#27374=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,7.985875536912E0)); -#27375=DIRECTION('',(-4.447028582079E-1,0.E0,-8.956781608936E-1)); -#27376=DIRECTION('',(-8.956781608936E-1,0.E0,4.447028582079E-1)); -#27377=AXIS2_PLACEMENT_3D('',#27374,#27375,#27376); -#27378=PLANE('',#27377); -#27379=ORIENTED_EDGE('',*,*,#24590,.F.); -#27381=ORIENTED_EDGE('',*,*,#27380,.T.); -#27383=ORIENTED_EDGE('',*,*,#27382,.T.); -#27384=ORIENTED_EDGE('',*,*,#27366,.F.); -#27385=EDGE_LOOP('',(#27379,#27381,#27383,#27384)); -#27386=FACE_OUTER_BOUND('',#27385,.F.); -#27388=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,7.957705439802E0)); -#27389=DIRECTION('',(-2.154818712031E-1,0.E0,-9.765078408199E-1)); -#27390=DIRECTION('',(-9.765078408199E-1,0.E0,2.154818712031E-1)); -#27391=AXIS2_PLACEMENT_3D('',#27388,#27389,#27390); -#27392=PLANE('',#27391); -#27393=ORIENTED_EDGE('',*,*,#24588,.F.); -#27395=ORIENTED_EDGE('',*,*,#27394,.T.); -#27397=ORIENTED_EDGE('',*,*,#27396,.T.); -#27398=ORIENTED_EDGE('',*,*,#27380,.F.); -#27399=EDGE_LOOP('',(#27393,#27395,#27397,#27398)); -#27400=FACE_OUTER_BOUND('',#27399,.F.); -#27402=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,7.957705439802E0)); -#27403=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27404=DIRECTION('',(-1.E0,0.E0,0.E0)); -#27405=AXIS2_PLACEMENT_3D('',#27402,#27403,#27404); -#27406=PLANE('',#27405); -#27407=ORIENTED_EDGE('',*,*,#24586,.F.); -#27409=ORIENTED_EDGE('',*,*,#27408,.T.); -#27411=ORIENTED_EDGE('',*,*,#27410,.T.); -#27412=ORIENTED_EDGE('',*,*,#27394,.F.); -#27413=EDGE_LOOP('',(#27407,#27409,#27411,#27412)); -#27414=FACE_OUTER_BOUND('',#27413,.F.); -#27416=CARTESIAN_POINT('',(7.659574747086E-1,1.55E0,7.985875536912E0)); -#27417=DIRECTION('',(2.154818712031E-1,0.E0,-9.765078408199E-1)); -#27418=DIRECTION('',(-9.765078408199E-1,0.E0,-2.154818712031E-1)); -#27419=AXIS2_PLACEMENT_3D('',#27416,#27417,#27418); -#27420=PLANE('',#27419); -#27421=ORIENTED_EDGE('',*,*,#24584,.F.); -#27423=ORIENTED_EDGE('',*,*,#27422,.T.); -#27425=ORIENTED_EDGE('',*,*,#27424,.T.); -#27426=ORIENTED_EDGE('',*,*,#27408,.F.); -#27427=EDGE_LOOP('',(#27421,#27423,#27425,#27426)); -#27428=FACE_OUTER_BOUND('',#27427,.F.); -#27430=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,8.070385908836E0)); -#27431=DIRECTION('',(4.447028582079E-1,0.E0,-8.956781608936E-1)); -#27432=DIRECTION('',(-8.956781608936E-1,0.E0,-4.447028582079E-1)); -#27433=AXIS2_PLACEMENT_3D('',#27430,#27431,#27432); -#27434=PLANE('',#27433); -#27435=ORIENTED_EDGE('',*,*,#24582,.F.); -#27436=ORIENTED_EDGE('',*,*,#27187,.T.); -#27438=ORIENTED_EDGE('',*,*,#27437,.T.); -#27439=ORIENTED_EDGE('',*,*,#27422,.F.); -#27440=EDGE_LOOP('',(#27435,#27436,#27438,#27439)); -#27441=FACE_OUTER_BOUND('',#27440,.F.); -#27443=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27444=DIRECTION('',(0.E0,1.E0,0.E0)); -#27445=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27446=AXIS2_PLACEMENT_3D('',#27443,#27444,#27445); -#27447=PLANE('',#27446); -#27448=ORIENTED_EDGE('',*,*,#27185,.F.); -#27449=ORIENTED_EDGE('',*,*,#27200,.F.); -#27450=ORIENTED_EDGE('',*,*,#27214,.F.); -#27451=ORIENTED_EDGE('',*,*,#27228,.F.); -#27452=ORIENTED_EDGE('',*,*,#27242,.F.); -#27453=ORIENTED_EDGE('',*,*,#27256,.F.); -#27454=ORIENTED_EDGE('',*,*,#27270,.F.); -#27455=ORIENTED_EDGE('',*,*,#27284,.F.); -#27456=ORIENTED_EDGE('',*,*,#27298,.F.); -#27457=ORIENTED_EDGE('',*,*,#27312,.F.); -#27458=ORIENTED_EDGE('',*,*,#27326,.F.); -#27459=ORIENTED_EDGE('',*,*,#27340,.F.); -#27460=ORIENTED_EDGE('',*,*,#27354,.F.); -#27461=ORIENTED_EDGE('',*,*,#27368,.F.); -#27462=ORIENTED_EDGE('',*,*,#27382,.F.); -#27463=ORIENTED_EDGE('',*,*,#27396,.F.); -#27464=ORIENTED_EDGE('',*,*,#27410,.F.); -#27465=ORIENTED_EDGE('',*,*,#27424,.F.); -#27466=ORIENTED_EDGE('',*,*,#27437,.F.); -#27467=EDGE_LOOP('',(#27448,#27449,#27450,#27451,#27452,#27453,#27454,#27455, -#27456,#27457,#27458,#27459,#27460,#27461,#27462,#27463,#27464,#27465,#27466)); -#27468=FACE_OUTER_BOUND('',#27467,.F.); -#27470=ORIENTED_EDGE('',*,*,#27469,.F.); -#27472=ORIENTED_EDGE('',*,*,#27471,.F.); -#27474=ORIENTED_EDGE('',*,*,#27473,.F.); -#27476=ORIENTED_EDGE('',*,*,#27475,.F.); -#27478=ORIENTED_EDGE('',*,*,#27477,.F.); -#27480=ORIENTED_EDGE('',*,*,#27479,.F.); -#27482=ORIENTED_EDGE('',*,*,#27481,.F.); -#27484=ORIENTED_EDGE('',*,*,#27483,.F.); -#27486=ORIENTED_EDGE('',*,*,#27485,.F.); -#27488=ORIENTED_EDGE('',*,*,#27487,.F.); -#27489=EDGE_LOOP('',(#27470,#27472,#27474,#27476,#27478,#27480,#27482,#27484, -#27486,#27488)); -#27490=FACE_BOUND('',#27489,.F.); -#27492=ORIENTED_EDGE('',*,*,#27491,.F.); -#27494=ORIENTED_EDGE('',*,*,#27493,.F.); -#27496=ORIENTED_EDGE('',*,*,#27495,.F.); -#27498=ORIENTED_EDGE('',*,*,#27497,.F.); -#27500=ORIENTED_EDGE('',*,*,#27499,.F.); -#27502=ORIENTED_EDGE('',*,*,#27501,.F.); -#27504=ORIENTED_EDGE('',*,*,#27503,.F.); -#27506=ORIENTED_EDGE('',*,*,#27505,.F.); -#27508=ORIENTED_EDGE('',*,*,#27507,.F.); -#27510=ORIENTED_EDGE('',*,*,#27509,.F.); -#27511=EDGE_LOOP('',(#27492,#27494,#27496,#27498,#27500,#27502,#27504,#27506, -#27508,#27510)); -#27512=FACE_BOUND('',#27511,.F.); -#27514=FILL_AREA_STYLE_COLOUR('',#17); -#27515=FILL_AREA_STYLE('',(#27514)); -#27516=SURFACE_STYLE_FILL_AREA(#27515); -#27517=SURFACE_SIDE_STYLE('',(#27516)); -#27518=SURFACE_STYLE_USAGE(.POSITIVE.,#27517); -#27519=PRESENTATION_STYLE_ASSIGNMENT((#27518)); -#27520=STYLED_ITEM('',(#27519),#27513); -#27521=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27522=DIRECTION('',(0.E0,1.E0,0.E0)); -#27523=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27524=AXIS2_PLACEMENT_3D('',#27521,#27522,#27523); -#27525=PLANE('',#27524); -#27527=ORIENTED_EDGE('',*,*,#27526,.F.); -#27529=ORIENTED_EDGE('',*,*,#27528,.F.); -#27531=ORIENTED_EDGE('',*,*,#27530,.F.); -#27533=ORIENTED_EDGE('',*,*,#27532,.F.); -#27535=ORIENTED_EDGE('',*,*,#27534,.F.); -#27537=ORIENTED_EDGE('',*,*,#27536,.F.); -#27539=ORIENTED_EDGE('',*,*,#27538,.F.); -#27541=ORIENTED_EDGE('',*,*,#27540,.F.); -#27542=EDGE_LOOP('',(#27527,#27529,#27531,#27533,#27535,#27537,#27539,#27541)); -#27543=FACE_OUTER_BOUND('',#27542,.F.); -#27545=FILL_AREA_STYLE_COLOUR('',#17); -#27546=FILL_AREA_STYLE('',(#27545)); -#27547=SURFACE_STYLE_FILL_AREA(#27546); -#27548=SURFACE_SIDE_STYLE('',(#27547)); -#27549=SURFACE_STYLE_USAGE(.POSITIVE.,#27548); -#27550=PRESENTATION_STYLE_ASSIGNMENT((#27549)); -#27551=STYLED_ITEM('',(#27550),#27544); -#27552=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27553=DIRECTION('',(0.E0,1.E0,0.E0)); -#27554=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27555=AXIS2_PLACEMENT_3D('',#27552,#27553,#27554); -#27556=PLANE('',#27555); -#27558=ORIENTED_EDGE('',*,*,#27557,.F.); -#27560=ORIENTED_EDGE('',*,*,#27559,.F.); -#27562=ORIENTED_EDGE('',*,*,#27561,.F.); -#27564=ORIENTED_EDGE('',*,*,#27563,.F.); -#27566=ORIENTED_EDGE('',*,*,#27565,.F.); -#27568=ORIENTED_EDGE('',*,*,#27567,.F.); -#27570=ORIENTED_EDGE('',*,*,#27569,.F.); -#27572=ORIENTED_EDGE('',*,*,#27571,.F.); -#27574=ORIENTED_EDGE('',*,*,#27573,.F.); -#27576=ORIENTED_EDGE('',*,*,#27575,.F.); -#27578=ORIENTED_EDGE('',*,*,#27577,.F.); -#27580=ORIENTED_EDGE('',*,*,#27579,.F.); -#27582=ORIENTED_EDGE('',*,*,#27581,.F.); -#27584=ORIENTED_EDGE('',*,*,#27583,.F.); -#27586=ORIENTED_EDGE('',*,*,#27585,.F.); -#27588=ORIENTED_EDGE('',*,*,#27587,.F.); -#27590=ORIENTED_EDGE('',*,*,#27589,.F.); -#27592=ORIENTED_EDGE('',*,*,#27591,.F.); -#27594=ORIENTED_EDGE('',*,*,#27593,.F.); -#27596=ORIENTED_EDGE('',*,*,#27595,.F.); -#27598=ORIENTED_EDGE('',*,*,#27597,.F.); -#27600=ORIENTED_EDGE('',*,*,#27599,.F.); -#27602=ORIENTED_EDGE('',*,*,#27601,.F.); -#27604=ORIENTED_EDGE('',*,*,#27603,.F.); -#27606=ORIENTED_EDGE('',*,*,#27605,.F.); -#27608=ORIENTED_EDGE('',*,*,#27607,.F.); -#27610=ORIENTED_EDGE('',*,*,#27609,.F.); -#27612=ORIENTED_EDGE('',*,*,#27611,.F.); -#27614=ORIENTED_EDGE('',*,*,#27613,.F.); -#27616=ORIENTED_EDGE('',*,*,#27615,.F.); -#27618=ORIENTED_EDGE('',*,*,#27617,.F.); -#27620=ORIENTED_EDGE('',*,*,#27619,.F.); -#27622=ORIENTED_EDGE('',*,*,#27621,.F.); -#27624=ORIENTED_EDGE('',*,*,#27623,.F.); -#27625=EDGE_LOOP('',(#27558,#27560,#27562,#27564,#27566,#27568,#27570,#27572, -#27574,#27576,#27578,#27580,#27582,#27584,#27586,#27588,#27590,#27592,#27594, -#27596,#27598,#27600,#27602,#27604,#27606,#27608,#27610,#27612,#27614,#27616, -#27618,#27620,#27622,#27624)); -#27626=FACE_OUTER_BOUND('',#27625,.F.); -#27628=ORIENTED_EDGE('',*,*,#27627,.F.); -#27630=ORIENTED_EDGE('',*,*,#27629,.F.); -#27632=ORIENTED_EDGE('',*,*,#27631,.F.); -#27634=ORIENTED_EDGE('',*,*,#27633,.F.); -#27636=ORIENTED_EDGE('',*,*,#27635,.F.); -#27638=ORIENTED_EDGE('',*,*,#27637,.F.); -#27640=ORIENTED_EDGE('',*,*,#27639,.F.); -#27642=ORIENTED_EDGE('',*,*,#27641,.F.); -#27644=ORIENTED_EDGE('',*,*,#27643,.F.); -#27646=ORIENTED_EDGE('',*,*,#27645,.F.); -#27648=ORIENTED_EDGE('',*,*,#27647,.F.); -#27650=ORIENTED_EDGE('',*,*,#27649,.F.); -#27652=ORIENTED_EDGE('',*,*,#27651,.F.); -#27654=ORIENTED_EDGE('',*,*,#27653,.F.); -#27656=ORIENTED_EDGE('',*,*,#27655,.F.); -#27658=ORIENTED_EDGE('',*,*,#27657,.F.); -#27659=EDGE_LOOP('',(#27628,#27630,#27632,#27634,#27636,#27638,#27640,#27642, -#27644,#27646,#27648,#27650,#27652,#27654,#27656,#27658)); -#27660=FACE_BOUND('',#27659,.F.); -#27662=ORIENTED_EDGE('',*,*,#27661,.F.); -#27664=ORIENTED_EDGE('',*,*,#27663,.F.); -#27666=ORIENTED_EDGE('',*,*,#27665,.F.); -#27668=ORIENTED_EDGE('',*,*,#27667,.F.); -#27670=ORIENTED_EDGE('',*,*,#27669,.F.); -#27672=ORIENTED_EDGE('',*,*,#27671,.F.); -#27674=ORIENTED_EDGE('',*,*,#27673,.F.); -#27676=ORIENTED_EDGE('',*,*,#27675,.F.); -#27678=ORIENTED_EDGE('',*,*,#27677,.F.); -#27680=ORIENTED_EDGE('',*,*,#27679,.F.); -#27682=ORIENTED_EDGE('',*,*,#27681,.F.); -#27684=ORIENTED_EDGE('',*,*,#27683,.F.); -#27686=ORIENTED_EDGE('',*,*,#27685,.F.); -#27688=ORIENTED_EDGE('',*,*,#27687,.F.); -#27690=ORIENTED_EDGE('',*,*,#27689,.F.); -#27692=ORIENTED_EDGE('',*,*,#27691,.F.); -#27693=EDGE_LOOP('',(#27662,#27664,#27666,#27668,#27670,#27672,#27674,#27676, -#27678,#27680,#27682,#27684,#27686,#27688,#27690,#27692)); -#27694=FACE_BOUND('',#27693,.F.); -#27696=FILL_AREA_STYLE_COLOUR('',#17); -#27697=FILL_AREA_STYLE('',(#27696)); -#27698=SURFACE_STYLE_FILL_AREA(#27697); -#27699=SURFACE_SIDE_STYLE('',(#27698)); -#27700=SURFACE_STYLE_USAGE(.POSITIVE.,#27699); -#27701=PRESENTATION_STYLE_ASSIGNMENT((#27700)); -#27702=STYLED_ITEM('',(#27701),#27695); -#27703=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27704=DIRECTION('',(0.E0,1.E0,0.E0)); -#27705=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27706=AXIS2_PLACEMENT_3D('',#27703,#27704,#27705); -#27707=PLANE('',#27706); -#27709=ORIENTED_EDGE('',*,*,#27708,.F.); -#27711=ORIENTED_EDGE('',*,*,#27710,.F.); -#27713=ORIENTED_EDGE('',*,*,#27712,.F.); -#27715=ORIENTED_EDGE('',*,*,#27714,.F.); -#27717=ORIENTED_EDGE('',*,*,#27716,.F.); -#27719=ORIENTED_EDGE('',*,*,#27718,.F.); -#27721=ORIENTED_EDGE('',*,*,#27720,.F.); -#27723=ORIENTED_EDGE('',*,*,#27722,.F.); -#27725=ORIENTED_EDGE('',*,*,#27724,.F.); -#27727=ORIENTED_EDGE('',*,*,#27726,.F.); -#27729=ORIENTED_EDGE('',*,*,#27728,.F.); -#27731=ORIENTED_EDGE('',*,*,#27730,.F.); -#27733=ORIENTED_EDGE('',*,*,#27732,.F.); -#27735=ORIENTED_EDGE('',*,*,#27734,.F.); -#27737=ORIENTED_EDGE('',*,*,#27736,.F.); -#27739=ORIENTED_EDGE('',*,*,#27738,.F.); -#27741=ORIENTED_EDGE('',*,*,#27740,.F.); -#27743=ORIENTED_EDGE('',*,*,#27742,.F.); -#27745=ORIENTED_EDGE('',*,*,#27744,.F.); -#27747=ORIENTED_EDGE('',*,*,#27746,.F.); -#27749=ORIENTED_EDGE('',*,*,#27748,.F.); -#27751=ORIENTED_EDGE('',*,*,#27750,.F.); -#27753=ORIENTED_EDGE('',*,*,#27752,.F.); -#27755=ORIENTED_EDGE('',*,*,#27754,.F.); -#27757=ORIENTED_EDGE('',*,*,#27756,.F.); -#27759=ORIENTED_EDGE('',*,*,#27758,.F.); -#27761=ORIENTED_EDGE('',*,*,#27760,.F.); -#27763=ORIENTED_EDGE('',*,*,#27762,.F.); -#27765=ORIENTED_EDGE('',*,*,#27764,.F.); -#27767=ORIENTED_EDGE('',*,*,#27766,.F.); -#27769=ORIENTED_EDGE('',*,*,#27768,.F.); -#27771=ORIENTED_EDGE('',*,*,#27770,.F.); -#27773=ORIENTED_EDGE('',*,*,#27772,.F.); -#27775=ORIENTED_EDGE('',*,*,#27774,.F.); -#27777=ORIENTED_EDGE('',*,*,#27776,.F.); -#27779=ORIENTED_EDGE('',*,*,#27778,.F.); -#27781=ORIENTED_EDGE('',*,*,#27780,.F.); -#27783=ORIENTED_EDGE('',*,*,#27782,.F.); -#27785=ORIENTED_EDGE('',*,*,#27784,.F.); -#27787=ORIENTED_EDGE('',*,*,#27786,.F.); -#27789=ORIENTED_EDGE('',*,*,#27788,.F.); -#27791=ORIENTED_EDGE('',*,*,#27790,.F.); -#27793=ORIENTED_EDGE('',*,*,#27792,.F.); -#27795=ORIENTED_EDGE('',*,*,#27794,.F.); -#27797=ORIENTED_EDGE('',*,*,#27796,.F.); -#27799=ORIENTED_EDGE('',*,*,#27798,.F.); -#27801=ORIENTED_EDGE('',*,*,#27800,.F.); -#27803=ORIENTED_EDGE('',*,*,#27802,.F.); -#27805=ORIENTED_EDGE('',*,*,#27804,.F.); -#27807=ORIENTED_EDGE('',*,*,#27806,.F.); -#27809=ORIENTED_EDGE('',*,*,#27808,.F.); -#27811=ORIENTED_EDGE('',*,*,#27810,.F.); -#27813=ORIENTED_EDGE('',*,*,#27812,.F.); -#27815=ORIENTED_EDGE('',*,*,#27814,.F.); -#27817=ORIENTED_EDGE('',*,*,#27816,.F.); -#27819=ORIENTED_EDGE('',*,*,#27818,.F.); -#27821=ORIENTED_EDGE('',*,*,#27820,.F.); -#27822=EDGE_LOOP('',(#27709,#27711,#27713,#27715,#27717,#27719,#27721,#27723, -#27725,#27727,#27729,#27731,#27733,#27735,#27737,#27739,#27741,#27743,#27745, -#27747,#27749,#27751,#27753,#27755,#27757,#27759,#27761,#27763,#27765,#27767, -#27769,#27771,#27773,#27775,#27777,#27779,#27781,#27783,#27785,#27787,#27789, -#27791,#27793,#27795,#27797,#27799,#27801,#27803,#27805,#27807,#27809,#27811, -#27813,#27815,#27817,#27819,#27821)); -#27823=FACE_OUTER_BOUND('',#27822,.F.); -#27825=FILL_AREA_STYLE_COLOUR('',#17); -#27826=FILL_AREA_STYLE('',(#27825)); -#27827=SURFACE_STYLE_FILL_AREA(#27826); -#27828=SURFACE_SIDE_STYLE('',(#27827)); -#27829=SURFACE_STYLE_USAGE(.POSITIVE.,#27828); -#27830=PRESENTATION_STYLE_ASSIGNMENT((#27829)); -#27831=STYLED_ITEM('',(#27830),#27824); -#27832=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27833=DIRECTION('',(0.E0,1.E0,0.E0)); -#27834=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27835=AXIS2_PLACEMENT_3D('',#27832,#27833,#27834); -#27836=PLANE('',#27835); -#27838=ORIENTED_EDGE('',*,*,#27837,.F.); -#27840=ORIENTED_EDGE('',*,*,#27839,.F.); -#27842=ORIENTED_EDGE('',*,*,#27841,.F.); -#27844=ORIENTED_EDGE('',*,*,#27843,.F.); -#27846=ORIENTED_EDGE('',*,*,#27845,.F.); -#27848=ORIENTED_EDGE('',*,*,#27847,.F.); -#27850=ORIENTED_EDGE('',*,*,#27849,.F.); -#27852=ORIENTED_EDGE('',*,*,#27851,.F.); -#27854=ORIENTED_EDGE('',*,*,#27853,.F.); -#27856=ORIENTED_EDGE('',*,*,#27855,.F.); -#27858=ORIENTED_EDGE('',*,*,#27857,.F.); -#27860=ORIENTED_EDGE('',*,*,#27859,.F.); -#27862=ORIENTED_EDGE('',*,*,#27861,.F.); -#27864=ORIENTED_EDGE('',*,*,#27863,.F.); -#27866=ORIENTED_EDGE('',*,*,#27865,.F.); -#27868=ORIENTED_EDGE('',*,*,#27867,.F.); -#27870=ORIENTED_EDGE('',*,*,#27869,.F.); -#27872=ORIENTED_EDGE('',*,*,#27871,.F.); -#27874=ORIENTED_EDGE('',*,*,#27873,.F.); -#27876=ORIENTED_EDGE('',*,*,#27875,.F.); -#27878=ORIENTED_EDGE('',*,*,#27877,.F.); -#27880=ORIENTED_EDGE('',*,*,#27879,.F.); -#27882=ORIENTED_EDGE('',*,*,#27881,.F.); -#27884=ORIENTED_EDGE('',*,*,#27883,.F.); -#27886=ORIENTED_EDGE('',*,*,#27885,.F.); -#27888=ORIENTED_EDGE('',*,*,#27887,.F.); -#27890=ORIENTED_EDGE('',*,*,#27889,.F.); -#27892=ORIENTED_EDGE('',*,*,#27891,.F.); -#27893=EDGE_LOOP('',(#27838,#27840,#27842,#27844,#27846,#27848,#27850,#27852, -#27854,#27856,#27858,#27860,#27862,#27864,#27866,#27868,#27870,#27872,#27874, -#27876,#27878,#27880,#27882,#27884,#27886,#27888,#27890,#27892)); -#27894=FACE_OUTER_BOUND('',#27893,.F.); -#27896=FILL_AREA_STYLE_COLOUR('',#17); -#27897=FILL_AREA_STYLE('',(#27896)); -#27898=SURFACE_STYLE_FILL_AREA(#27897); -#27899=SURFACE_SIDE_STYLE('',(#27898)); -#27900=SURFACE_STYLE_USAGE(.POSITIVE.,#27899); -#27901=PRESENTATION_STYLE_ASSIGNMENT((#27900)); -#27902=STYLED_ITEM('',(#27901),#27895); -#27903=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27904=DIRECTION('',(0.E0,1.E0,0.E0)); -#27905=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27906=AXIS2_PLACEMENT_3D('',#27903,#27904,#27905); -#27907=PLANE('',#27906); -#27909=ORIENTED_EDGE('',*,*,#27908,.F.); -#27911=ORIENTED_EDGE('',*,*,#27910,.F.); -#27913=ORIENTED_EDGE('',*,*,#27912,.F.); -#27915=ORIENTED_EDGE('',*,*,#27914,.F.); -#27917=ORIENTED_EDGE('',*,*,#27916,.F.); -#27919=ORIENTED_EDGE('',*,*,#27918,.F.); -#27921=ORIENTED_EDGE('',*,*,#27920,.F.); -#27923=ORIENTED_EDGE('',*,*,#27922,.F.); -#27925=ORIENTED_EDGE('',*,*,#27924,.F.); -#27927=ORIENTED_EDGE('',*,*,#27926,.F.); -#27929=ORIENTED_EDGE('',*,*,#27928,.F.); -#27931=ORIENTED_EDGE('',*,*,#27930,.F.); -#27932=EDGE_LOOP('',(#27909,#27911,#27913,#27915,#27917,#27919,#27921,#27923, -#27925,#27927,#27929,#27931)); -#27933=FACE_OUTER_BOUND('',#27932,.F.); -#27935=FILL_AREA_STYLE_COLOUR('',#17); -#27936=FILL_AREA_STYLE('',(#27935)); -#27937=SURFACE_STYLE_FILL_AREA(#27936); -#27938=SURFACE_SIDE_STYLE('',(#27937)); -#27939=SURFACE_STYLE_USAGE(.POSITIVE.,#27938); -#27940=PRESENTATION_STYLE_ASSIGNMENT((#27939)); -#27941=STYLED_ITEM('',(#27940),#27934); -#27942=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27943=DIRECTION('',(0.E0,1.E0,0.E0)); -#27944=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27945=AXIS2_PLACEMENT_3D('',#27942,#27943,#27944); -#27946=PLANE('',#27945); -#27948=ORIENTED_EDGE('',*,*,#27947,.F.); -#27950=ORIENTED_EDGE('',*,*,#27949,.F.); -#27952=ORIENTED_EDGE('',*,*,#27951,.F.); -#27954=ORIENTED_EDGE('',*,*,#27953,.F.); -#27956=ORIENTED_EDGE('',*,*,#27955,.F.); -#27958=ORIENTED_EDGE('',*,*,#27957,.F.); -#27960=ORIENTED_EDGE('',*,*,#27959,.F.); -#27962=ORIENTED_EDGE('',*,*,#27961,.F.); -#27964=ORIENTED_EDGE('',*,*,#27963,.F.); -#27966=ORIENTED_EDGE('',*,*,#27965,.F.); -#27967=EDGE_LOOP('',(#27948,#27950,#27952,#27954,#27956,#27958,#27960,#27962, -#27964,#27966)); -#27968=FACE_OUTER_BOUND('',#27967,.F.); -#27970=FILL_AREA_STYLE_COLOUR('',#17); -#27971=FILL_AREA_STYLE('',(#27970)); -#27972=SURFACE_STYLE_FILL_AREA(#27971); -#27973=SURFACE_SIDE_STYLE('',(#27972)); -#27974=SURFACE_STYLE_USAGE(.POSITIVE.,#27973); -#27975=PRESENTATION_STYLE_ASSIGNMENT((#27974)); -#27976=STYLED_ITEM('',(#27975),#27969); -#27977=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#27978=DIRECTION('',(0.E0,1.E0,0.E0)); -#27979=DIRECTION('',(0.E0,0.E0,-1.E0)); -#27980=AXIS2_PLACEMENT_3D('',#27977,#27978,#27979); -#27981=PLANE('',#27980); -#27983=ORIENTED_EDGE('',*,*,#27982,.F.); -#27985=ORIENTED_EDGE('',*,*,#27984,.F.); -#27987=ORIENTED_EDGE('',*,*,#27986,.F.); -#27989=ORIENTED_EDGE('',*,*,#27988,.F.); -#27991=ORIENTED_EDGE('',*,*,#27990,.F.); -#27993=ORIENTED_EDGE('',*,*,#27992,.F.); -#27995=ORIENTED_EDGE('',*,*,#27994,.F.); -#27997=ORIENTED_EDGE('',*,*,#27996,.F.); -#27999=ORIENTED_EDGE('',*,*,#27998,.F.); -#28001=ORIENTED_EDGE('',*,*,#28000,.F.); -#28003=ORIENTED_EDGE('',*,*,#28002,.F.); -#28005=ORIENTED_EDGE('',*,*,#28004,.F.); -#28007=ORIENTED_EDGE('',*,*,#28006,.F.); -#28009=ORIENTED_EDGE('',*,*,#28008,.F.); -#28011=ORIENTED_EDGE('',*,*,#28010,.F.); -#28013=ORIENTED_EDGE('',*,*,#28012,.F.); -#28015=ORIENTED_EDGE('',*,*,#28014,.F.); -#28017=ORIENTED_EDGE('',*,*,#28016,.F.); -#28019=ORIENTED_EDGE('',*,*,#28018,.F.); -#28021=ORIENTED_EDGE('',*,*,#28020,.F.); -#28023=ORIENTED_EDGE('',*,*,#28022,.F.); -#28025=ORIENTED_EDGE('',*,*,#28024,.F.); -#28027=ORIENTED_EDGE('',*,*,#28026,.F.); -#28029=ORIENTED_EDGE('',*,*,#28028,.F.); -#28031=ORIENTED_EDGE('',*,*,#28030,.F.); -#28033=ORIENTED_EDGE('',*,*,#28032,.F.); -#28035=ORIENTED_EDGE('',*,*,#28034,.F.); -#28037=ORIENTED_EDGE('',*,*,#28036,.F.); -#28039=ORIENTED_EDGE('',*,*,#28038,.F.); -#28041=ORIENTED_EDGE('',*,*,#28040,.F.); -#28043=ORIENTED_EDGE('',*,*,#28042,.F.); -#28045=ORIENTED_EDGE('',*,*,#28044,.F.); -#28047=ORIENTED_EDGE('',*,*,#28046,.F.); -#28049=ORIENTED_EDGE('',*,*,#28048,.F.); -#28051=ORIENTED_EDGE('',*,*,#28050,.F.); -#28053=ORIENTED_EDGE('',*,*,#28052,.F.); -#28055=ORIENTED_EDGE('',*,*,#28054,.F.); -#28057=ORIENTED_EDGE('',*,*,#28056,.F.); -#28059=ORIENTED_EDGE('',*,*,#28058,.F.); -#28061=ORIENTED_EDGE('',*,*,#28060,.F.); -#28062=EDGE_LOOP('',(#27983,#27985,#27987,#27989,#27991,#27993,#27995,#27997, -#27999,#28001,#28003,#28005,#28007,#28009,#28011,#28013,#28015,#28017,#28019, -#28021,#28023,#28025,#28027,#28029,#28031,#28033,#28035,#28037,#28039,#28041, -#28043,#28045,#28047,#28049,#28051,#28053,#28055,#28057,#28059,#28061)); -#28063=FACE_OUTER_BOUND('',#28062,.F.); -#28065=FILL_AREA_STYLE_COLOUR('',#17); -#28066=FILL_AREA_STYLE('',(#28065)); -#28067=SURFACE_STYLE_FILL_AREA(#28066); -#28068=SURFACE_SIDE_STYLE('',(#28067)); -#28069=SURFACE_STYLE_USAGE(.POSITIVE.,#28068); -#28070=PRESENTATION_STYLE_ASSIGNMENT((#28069)); -#28071=STYLED_ITEM('',(#28070),#28064); -#28072=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28073=DIRECTION('',(0.E0,1.E0,0.E0)); -#28074=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28075=AXIS2_PLACEMENT_3D('',#28072,#28073,#28074); -#28076=PLANE('',#28075); -#28078=ORIENTED_EDGE('',*,*,#28077,.F.); -#28080=ORIENTED_EDGE('',*,*,#28079,.F.); -#28082=ORIENTED_EDGE('',*,*,#28081,.F.); -#28084=ORIENTED_EDGE('',*,*,#28083,.F.); -#28086=ORIENTED_EDGE('',*,*,#28085,.F.); -#28088=ORIENTED_EDGE('',*,*,#28087,.F.); -#28090=ORIENTED_EDGE('',*,*,#28089,.F.); -#28092=ORIENTED_EDGE('',*,*,#28091,.F.); -#28094=ORIENTED_EDGE('',*,*,#28093,.F.); -#28096=ORIENTED_EDGE('',*,*,#28095,.F.); -#28098=ORIENTED_EDGE('',*,*,#28097,.F.); -#28100=ORIENTED_EDGE('',*,*,#28099,.F.); -#28102=ORIENTED_EDGE('',*,*,#28101,.F.); -#28104=ORIENTED_EDGE('',*,*,#28103,.F.); -#28106=ORIENTED_EDGE('',*,*,#28105,.F.); -#28108=ORIENTED_EDGE('',*,*,#28107,.F.); -#28110=ORIENTED_EDGE('',*,*,#28109,.F.); -#28112=ORIENTED_EDGE('',*,*,#28111,.F.); -#28114=ORIENTED_EDGE('',*,*,#28113,.F.); -#28116=ORIENTED_EDGE('',*,*,#28115,.F.); -#28118=ORIENTED_EDGE('',*,*,#28117,.F.); -#28120=ORIENTED_EDGE('',*,*,#28119,.F.); -#28122=ORIENTED_EDGE('',*,*,#28121,.F.); -#28124=ORIENTED_EDGE('',*,*,#28123,.F.); -#28126=ORIENTED_EDGE('',*,*,#28125,.F.); -#28128=ORIENTED_EDGE('',*,*,#28127,.F.); -#28130=ORIENTED_EDGE('',*,*,#28129,.F.); -#28132=ORIENTED_EDGE('',*,*,#28131,.F.); -#28134=ORIENTED_EDGE('',*,*,#28133,.F.); -#28136=ORIENTED_EDGE('',*,*,#28135,.F.); -#28138=ORIENTED_EDGE('',*,*,#28137,.F.); -#28140=ORIENTED_EDGE('',*,*,#28139,.F.); -#28142=ORIENTED_EDGE('',*,*,#28141,.F.); -#28144=ORIENTED_EDGE('',*,*,#28143,.F.); -#28146=ORIENTED_EDGE('',*,*,#28145,.F.); -#28148=ORIENTED_EDGE('',*,*,#28147,.F.); -#28150=ORIENTED_EDGE('',*,*,#28149,.F.); -#28152=ORIENTED_EDGE('',*,*,#28151,.F.); -#28154=ORIENTED_EDGE('',*,*,#28153,.F.); -#28156=ORIENTED_EDGE('',*,*,#28155,.F.); -#28157=EDGE_LOOP('',(#28078,#28080,#28082,#28084,#28086,#28088,#28090,#28092, -#28094,#28096,#28098,#28100,#28102,#28104,#28106,#28108,#28110,#28112,#28114, -#28116,#28118,#28120,#28122,#28124,#28126,#28128,#28130,#28132,#28134,#28136, -#28138,#28140,#28142,#28144,#28146,#28148,#28150,#28152,#28154,#28156)); -#28158=FACE_OUTER_BOUND('',#28157,.F.); -#28160=FILL_AREA_STYLE_COLOUR('',#17); -#28161=FILL_AREA_STYLE('',(#28160)); -#28162=SURFACE_STYLE_FILL_AREA(#28161); -#28163=SURFACE_SIDE_STYLE('',(#28162)); -#28164=SURFACE_STYLE_USAGE(.POSITIVE.,#28163); -#28165=PRESENTATION_STYLE_ASSIGNMENT((#28164)); -#28166=STYLED_ITEM('',(#28165),#28159); -#28167=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28168=DIRECTION('',(0.E0,1.E0,0.E0)); -#28169=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28170=AXIS2_PLACEMENT_3D('',#28167,#28168,#28169); -#28171=PLANE('',#28170); -#28173=ORIENTED_EDGE('',*,*,#28172,.F.); -#28175=ORIENTED_EDGE('',*,*,#28174,.F.); -#28177=ORIENTED_EDGE('',*,*,#28176,.F.); -#28179=ORIENTED_EDGE('',*,*,#28178,.F.); -#28180=EDGE_LOOP('',(#28173,#28175,#28177,#28179)); -#28181=FACE_OUTER_BOUND('',#28180,.F.); -#28183=FILL_AREA_STYLE_COLOUR('',#17); -#28184=FILL_AREA_STYLE('',(#28183)); -#28185=SURFACE_STYLE_FILL_AREA(#28184); -#28186=SURFACE_SIDE_STYLE('',(#28185)); -#28187=SURFACE_STYLE_USAGE(.POSITIVE.,#28186); -#28188=PRESENTATION_STYLE_ASSIGNMENT((#28187)); -#28189=STYLED_ITEM('',(#28188),#28182); -#28190=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28191=DIRECTION('',(0.E0,1.E0,0.E0)); -#28192=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28193=AXIS2_PLACEMENT_3D('',#28190,#28191,#28192); -#28194=PLANE('',#28193); -#28196=ORIENTED_EDGE('',*,*,#28195,.F.); -#28198=ORIENTED_EDGE('',*,*,#28197,.F.); -#28200=ORIENTED_EDGE('',*,*,#28199,.F.); -#28202=ORIENTED_EDGE('',*,*,#28201,.F.); -#28204=ORIENTED_EDGE('',*,*,#28203,.F.); -#28206=ORIENTED_EDGE('',*,*,#28205,.F.); -#28208=ORIENTED_EDGE('',*,*,#28207,.F.); -#28210=ORIENTED_EDGE('',*,*,#28209,.F.); -#28212=ORIENTED_EDGE('',*,*,#28211,.F.); -#28214=ORIENTED_EDGE('',*,*,#28213,.F.); -#28216=ORIENTED_EDGE('',*,*,#28215,.F.); -#28218=ORIENTED_EDGE('',*,*,#28217,.F.); -#28220=ORIENTED_EDGE('',*,*,#28219,.F.); -#28222=ORIENTED_EDGE('',*,*,#28221,.F.); -#28223=EDGE_LOOP('',(#28196,#28198,#28200,#28202,#28204,#28206,#28208,#28210, -#28212,#28214,#28216,#28218,#28220,#28222)); -#28224=FACE_OUTER_BOUND('',#28223,.F.); -#28226=ORIENTED_EDGE('',*,*,#28225,.F.); -#28228=ORIENTED_EDGE('',*,*,#28227,.F.); -#28230=ORIENTED_EDGE('',*,*,#28229,.F.); -#28232=ORIENTED_EDGE('',*,*,#28231,.F.); -#28234=ORIENTED_EDGE('',*,*,#28233,.F.); -#28236=ORIENTED_EDGE('',*,*,#28235,.F.); -#28238=ORIENTED_EDGE('',*,*,#28237,.F.); -#28240=ORIENTED_EDGE('',*,*,#28239,.F.); -#28242=ORIENTED_EDGE('',*,*,#28241,.F.); -#28244=ORIENTED_EDGE('',*,*,#28243,.F.); -#28246=ORIENTED_EDGE('',*,*,#28245,.F.); -#28248=ORIENTED_EDGE('',*,*,#28247,.F.); -#28249=EDGE_LOOP('',(#28226,#28228,#28230,#28232,#28234,#28236,#28238,#28240, -#28242,#28244,#28246,#28248)); -#28250=FACE_BOUND('',#28249,.F.); -#28252=FILL_AREA_STYLE_COLOUR('',#17); -#28253=FILL_AREA_STYLE('',(#28252)); -#28254=SURFACE_STYLE_FILL_AREA(#28253); -#28255=SURFACE_SIDE_STYLE('',(#28254)); -#28256=SURFACE_STYLE_USAGE(.POSITIVE.,#28255); -#28257=PRESENTATION_STYLE_ASSIGNMENT((#28256)); -#28258=STYLED_ITEM('',(#28257),#28251); -#28259=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28260=DIRECTION('',(0.E0,1.E0,0.E0)); -#28261=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28262=AXIS2_PLACEMENT_3D('',#28259,#28260,#28261); -#28263=PLANE('',#28262); -#28265=ORIENTED_EDGE('',*,*,#28264,.F.); -#28267=ORIENTED_EDGE('',*,*,#28266,.F.); -#28269=ORIENTED_EDGE('',*,*,#28268,.F.); -#28271=ORIENTED_EDGE('',*,*,#28270,.F.); -#28272=EDGE_LOOP('',(#28265,#28267,#28269,#28271)); -#28273=FACE_OUTER_BOUND('',#28272,.F.); -#28275=FILL_AREA_STYLE_COLOUR('',#17); -#28276=FILL_AREA_STYLE('',(#28275)); -#28277=SURFACE_STYLE_FILL_AREA(#28276); -#28278=SURFACE_SIDE_STYLE('',(#28277)); -#28279=SURFACE_STYLE_USAGE(.POSITIVE.,#28278); -#28280=PRESENTATION_STYLE_ASSIGNMENT((#28279)); -#28281=STYLED_ITEM('',(#28280),#28274); -#28282=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28283=DIRECTION('',(0.E0,1.E0,0.E0)); -#28284=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28285=AXIS2_PLACEMENT_3D('',#28282,#28283,#28284); -#28286=PLANE('',#28285); -#28288=ORIENTED_EDGE('',*,*,#28287,.F.); -#28290=ORIENTED_EDGE('',*,*,#28289,.F.); -#28292=ORIENTED_EDGE('',*,*,#28291,.F.); -#28294=ORIENTED_EDGE('',*,*,#28293,.F.); -#28295=EDGE_LOOP('',(#28288,#28290,#28292,#28294)); -#28296=FACE_OUTER_BOUND('',#28295,.F.); -#28298=FILL_AREA_STYLE_COLOUR('',#17); -#28299=FILL_AREA_STYLE('',(#28298)); -#28300=SURFACE_STYLE_FILL_AREA(#28299); -#28301=SURFACE_SIDE_STYLE('',(#28300)); -#28302=SURFACE_STYLE_USAGE(.POSITIVE.,#28301); -#28303=PRESENTATION_STYLE_ASSIGNMENT((#28302)); -#28304=STYLED_ITEM('',(#28303),#28297); -#28305=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28306=DIRECTION('',(0.E0,1.E0,0.E0)); -#28307=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28308=AXIS2_PLACEMENT_3D('',#28305,#28306,#28307); -#28309=PLANE('',#28308); -#28311=ORIENTED_EDGE('',*,*,#28310,.F.); -#28313=ORIENTED_EDGE('',*,*,#28312,.F.); -#28315=ORIENTED_EDGE('',*,*,#28314,.F.); -#28317=ORIENTED_EDGE('',*,*,#28316,.F.); -#28319=ORIENTED_EDGE('',*,*,#28318,.F.); -#28321=ORIENTED_EDGE('',*,*,#28320,.F.); -#28323=ORIENTED_EDGE('',*,*,#28322,.F.); -#28325=ORIENTED_EDGE('',*,*,#28324,.F.); -#28327=ORIENTED_EDGE('',*,*,#28326,.F.); -#28329=ORIENTED_EDGE('',*,*,#28328,.F.); -#28331=ORIENTED_EDGE('',*,*,#28330,.F.); -#28333=ORIENTED_EDGE('',*,*,#28332,.F.); -#28334=EDGE_LOOP('',(#28311,#28313,#28315,#28317,#28319,#28321,#28323,#28325, -#28327,#28329,#28331,#28333)); -#28335=FACE_OUTER_BOUND('',#28334,.F.); -#28337=FILL_AREA_STYLE_COLOUR('',#17); -#28338=FILL_AREA_STYLE('',(#28337)); -#28339=SURFACE_STYLE_FILL_AREA(#28338); -#28340=SURFACE_SIDE_STYLE('',(#28339)); -#28341=SURFACE_STYLE_USAGE(.POSITIVE.,#28340); -#28342=PRESENTATION_STYLE_ASSIGNMENT((#28341)); -#28343=STYLED_ITEM('',(#28342),#28336); -#28344=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28345=DIRECTION('',(0.E0,1.E0,0.E0)); -#28346=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28347=AXIS2_PLACEMENT_3D('',#28344,#28345,#28346); -#28348=PLANE('',#28347); -#28350=ORIENTED_EDGE('',*,*,#28349,.F.); -#28352=ORIENTED_EDGE('',*,*,#28351,.F.); -#28354=ORIENTED_EDGE('',*,*,#28353,.F.); -#28356=ORIENTED_EDGE('',*,*,#28355,.F.); -#28358=ORIENTED_EDGE('',*,*,#28357,.F.); -#28360=ORIENTED_EDGE('',*,*,#28359,.F.); -#28362=ORIENTED_EDGE('',*,*,#28361,.F.); -#28364=ORIENTED_EDGE('',*,*,#28363,.F.); -#28366=ORIENTED_EDGE('',*,*,#28365,.F.); -#28368=ORIENTED_EDGE('',*,*,#28367,.F.); -#28370=ORIENTED_EDGE('',*,*,#28369,.F.); -#28372=ORIENTED_EDGE('',*,*,#28371,.F.); -#28374=ORIENTED_EDGE('',*,*,#28373,.F.); -#28376=ORIENTED_EDGE('',*,*,#28375,.F.); -#28378=ORIENTED_EDGE('',*,*,#28377,.F.); -#28380=ORIENTED_EDGE('',*,*,#28379,.F.); -#28382=ORIENTED_EDGE('',*,*,#28381,.F.); -#28384=ORIENTED_EDGE('',*,*,#28383,.F.); -#28386=ORIENTED_EDGE('',*,*,#28385,.F.); -#28388=ORIENTED_EDGE('',*,*,#28387,.F.); -#28390=ORIENTED_EDGE('',*,*,#28389,.F.); -#28392=ORIENTED_EDGE('',*,*,#28391,.F.); -#28394=ORIENTED_EDGE('',*,*,#28393,.F.); -#28396=ORIENTED_EDGE('',*,*,#28395,.F.); -#28398=ORIENTED_EDGE('',*,*,#28397,.F.); -#28400=ORIENTED_EDGE('',*,*,#28399,.F.); -#28402=ORIENTED_EDGE('',*,*,#28401,.F.); -#28404=ORIENTED_EDGE('',*,*,#28403,.F.); -#28406=ORIENTED_EDGE('',*,*,#28405,.F.); -#28408=ORIENTED_EDGE('',*,*,#28407,.F.); -#28410=ORIENTED_EDGE('',*,*,#28409,.F.); -#28412=ORIENTED_EDGE('',*,*,#28411,.F.); -#28414=ORIENTED_EDGE('',*,*,#28413,.F.); -#28416=ORIENTED_EDGE('',*,*,#28415,.F.); -#28417=EDGE_LOOP('',(#28350,#28352,#28354,#28356,#28358,#28360,#28362,#28364, -#28366,#28368,#28370,#28372,#28374,#28376,#28378,#28380,#28382,#28384,#28386, -#28388,#28390,#28392,#28394,#28396,#28398,#28400,#28402,#28404,#28406,#28408, -#28410,#28412,#28414,#28416)); -#28418=FACE_OUTER_BOUND('',#28417,.F.); -#28420=ORIENTED_EDGE('',*,*,#28419,.F.); -#28422=ORIENTED_EDGE('',*,*,#28421,.F.); -#28424=ORIENTED_EDGE('',*,*,#28423,.F.); -#28426=ORIENTED_EDGE('',*,*,#28425,.F.); -#28428=ORIENTED_EDGE('',*,*,#28427,.F.); -#28430=ORIENTED_EDGE('',*,*,#28429,.F.); -#28432=ORIENTED_EDGE('',*,*,#28431,.F.); -#28434=ORIENTED_EDGE('',*,*,#28433,.F.); -#28436=ORIENTED_EDGE('',*,*,#28435,.F.); -#28438=ORIENTED_EDGE('',*,*,#28437,.F.); -#28440=ORIENTED_EDGE('',*,*,#28439,.F.); -#28442=ORIENTED_EDGE('',*,*,#28441,.F.); -#28444=ORIENTED_EDGE('',*,*,#28443,.F.); -#28446=ORIENTED_EDGE('',*,*,#28445,.F.); -#28448=ORIENTED_EDGE('',*,*,#28447,.F.); -#28450=ORIENTED_EDGE('',*,*,#28449,.F.); -#28451=EDGE_LOOP('',(#28420,#28422,#28424,#28426,#28428,#28430,#28432,#28434, -#28436,#28438,#28440,#28442,#28444,#28446,#28448,#28450)); -#28452=FACE_BOUND('',#28451,.F.); -#28454=ORIENTED_EDGE('',*,*,#28453,.F.); -#28456=ORIENTED_EDGE('',*,*,#28455,.F.); -#28458=ORIENTED_EDGE('',*,*,#28457,.F.); -#28460=ORIENTED_EDGE('',*,*,#28459,.F.); -#28462=ORIENTED_EDGE('',*,*,#28461,.F.); -#28464=ORIENTED_EDGE('',*,*,#28463,.F.); -#28466=ORIENTED_EDGE('',*,*,#28465,.F.); -#28468=ORIENTED_EDGE('',*,*,#28467,.F.); -#28470=ORIENTED_EDGE('',*,*,#28469,.F.); -#28472=ORIENTED_EDGE('',*,*,#28471,.F.); -#28474=ORIENTED_EDGE('',*,*,#28473,.F.); -#28476=ORIENTED_EDGE('',*,*,#28475,.F.); -#28478=ORIENTED_EDGE('',*,*,#28477,.F.); -#28480=ORIENTED_EDGE('',*,*,#28479,.F.); -#28482=ORIENTED_EDGE('',*,*,#28481,.F.); -#28484=ORIENTED_EDGE('',*,*,#28483,.F.); -#28485=EDGE_LOOP('',(#28454,#28456,#28458,#28460,#28462,#28464,#28466,#28468, -#28470,#28472,#28474,#28476,#28478,#28480,#28482,#28484)); -#28486=FACE_BOUND('',#28485,.F.); -#28488=FILL_AREA_STYLE_COLOUR('',#17); -#28489=FILL_AREA_STYLE('',(#28488)); -#28490=SURFACE_STYLE_FILL_AREA(#28489); -#28491=SURFACE_SIDE_STYLE('',(#28490)); -#28492=SURFACE_STYLE_USAGE(.POSITIVE.,#28491); -#28493=PRESENTATION_STYLE_ASSIGNMENT((#28492)); -#28494=STYLED_ITEM('',(#28493),#28487); -#28495=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28496=DIRECTION('',(0.E0,1.E0,0.E0)); -#28497=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28498=AXIS2_PLACEMENT_3D('',#28495,#28496,#28497); -#28499=PLANE('',#28498); -#28501=ORIENTED_EDGE('',*,*,#28500,.F.); -#28503=ORIENTED_EDGE('',*,*,#28502,.F.); -#28505=ORIENTED_EDGE('',*,*,#28504,.F.); -#28507=ORIENTED_EDGE('',*,*,#28506,.F.); -#28509=ORIENTED_EDGE('',*,*,#28508,.F.); -#28511=ORIENTED_EDGE('',*,*,#28510,.F.); -#28513=ORIENTED_EDGE('',*,*,#28512,.F.); -#28515=ORIENTED_EDGE('',*,*,#28514,.F.); -#28517=ORIENTED_EDGE('',*,*,#28516,.F.); -#28519=ORIENTED_EDGE('',*,*,#28518,.F.); -#28521=ORIENTED_EDGE('',*,*,#28520,.F.); -#28523=ORIENTED_EDGE('',*,*,#28522,.F.); -#28525=ORIENTED_EDGE('',*,*,#28524,.F.); -#28526=EDGE_LOOP('',(#28501,#28503,#28505,#28507,#28509,#28511,#28513,#28515, -#28517,#28519,#28521,#28523,#28525)); -#28527=FACE_OUTER_BOUND('',#28526,.F.); -#28529=FILL_AREA_STYLE_COLOUR('',#17); -#28530=FILL_AREA_STYLE('',(#28529)); -#28531=SURFACE_STYLE_FILL_AREA(#28530); -#28532=SURFACE_SIDE_STYLE('',(#28531)); -#28533=SURFACE_STYLE_USAGE(.POSITIVE.,#28532); -#28534=PRESENTATION_STYLE_ASSIGNMENT((#28533)); -#28535=STYLED_ITEM('',(#28534),#28528); -#28536=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28537=DIRECTION('',(0.E0,1.E0,0.E0)); -#28538=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28539=AXIS2_PLACEMENT_3D('',#28536,#28537,#28538); -#28540=PLANE('',#28539); -#28542=ORIENTED_EDGE('',*,*,#28541,.F.); -#28544=ORIENTED_EDGE('',*,*,#28543,.F.); -#28546=ORIENTED_EDGE('',*,*,#28545,.F.); -#28548=ORIENTED_EDGE('',*,*,#28547,.F.); -#28550=ORIENTED_EDGE('',*,*,#28549,.F.); -#28552=ORIENTED_EDGE('',*,*,#28551,.F.); -#28554=ORIENTED_EDGE('',*,*,#28553,.F.); -#28556=ORIENTED_EDGE('',*,*,#28555,.F.); -#28558=ORIENTED_EDGE('',*,*,#28557,.F.); -#28560=ORIENTED_EDGE('',*,*,#28559,.F.); -#28562=ORIENTED_EDGE('',*,*,#28561,.F.); -#28564=ORIENTED_EDGE('',*,*,#28563,.F.); -#28566=ORIENTED_EDGE('',*,*,#28565,.F.); -#28568=ORIENTED_EDGE('',*,*,#28567,.F.); -#28570=ORIENTED_EDGE('',*,*,#28569,.F.); -#28572=ORIENTED_EDGE('',*,*,#28571,.F.); -#28574=ORIENTED_EDGE('',*,*,#28573,.F.); -#28576=ORIENTED_EDGE('',*,*,#28575,.F.); -#28578=ORIENTED_EDGE('',*,*,#28577,.F.); -#28579=EDGE_LOOP('',(#28542,#28544,#28546,#28548,#28550,#28552,#28554,#28556, -#28558,#28560,#28562,#28564,#28566,#28568,#28570,#28572,#28574,#28576,#28578)); -#28580=FACE_OUTER_BOUND('',#28579,.F.); -#28582=ORIENTED_EDGE('',*,*,#28581,.F.); -#28584=ORIENTED_EDGE('',*,*,#28583,.F.); -#28586=ORIENTED_EDGE('',*,*,#28585,.F.); -#28588=ORIENTED_EDGE('',*,*,#28587,.F.); -#28590=ORIENTED_EDGE('',*,*,#28589,.F.); -#28592=ORIENTED_EDGE('',*,*,#28591,.F.); -#28594=ORIENTED_EDGE('',*,*,#28593,.F.); -#28596=ORIENTED_EDGE('',*,*,#28595,.F.); -#28598=ORIENTED_EDGE('',*,*,#28597,.F.); -#28600=ORIENTED_EDGE('',*,*,#28599,.F.); -#28601=EDGE_LOOP('',(#28582,#28584,#28586,#28588,#28590,#28592,#28594,#28596, -#28598,#28600)); -#28602=FACE_BOUND('',#28601,.F.); -#28604=ORIENTED_EDGE('',*,*,#28603,.F.); -#28606=ORIENTED_EDGE('',*,*,#28605,.F.); -#28608=ORIENTED_EDGE('',*,*,#28607,.F.); -#28610=ORIENTED_EDGE('',*,*,#28609,.F.); -#28612=ORIENTED_EDGE('',*,*,#28611,.F.); -#28614=ORIENTED_EDGE('',*,*,#28613,.F.); -#28616=ORIENTED_EDGE('',*,*,#28615,.F.); -#28618=ORIENTED_EDGE('',*,*,#28617,.F.); -#28620=ORIENTED_EDGE('',*,*,#28619,.F.); -#28622=ORIENTED_EDGE('',*,*,#28621,.F.); -#28623=EDGE_LOOP('',(#28604,#28606,#28608,#28610,#28612,#28614,#28616,#28618, -#28620,#28622)); -#28624=FACE_BOUND('',#28623,.F.); -#28626=FILL_AREA_STYLE_COLOUR('',#17); -#28627=FILL_AREA_STYLE('',(#28626)); -#28628=SURFACE_STYLE_FILL_AREA(#28627); -#28629=SURFACE_SIDE_STYLE('',(#28628)); -#28630=SURFACE_STYLE_USAGE(.POSITIVE.,#28629); -#28631=PRESENTATION_STYLE_ASSIGNMENT((#28630)); -#28632=STYLED_ITEM('',(#28631),#28625); -#28633=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28634=DIRECTION('',(0.E0,1.E0,0.E0)); -#28635=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28636=AXIS2_PLACEMENT_3D('',#28633,#28634,#28635); -#28637=PLANE('',#28636); -#28639=ORIENTED_EDGE('',*,*,#28638,.F.); -#28641=ORIENTED_EDGE('',*,*,#28640,.F.); -#28643=ORIENTED_EDGE('',*,*,#28642,.F.); -#28645=ORIENTED_EDGE('',*,*,#28644,.F.); -#28647=ORIENTED_EDGE('',*,*,#28646,.F.); -#28649=ORIENTED_EDGE('',*,*,#28648,.F.); -#28651=ORIENTED_EDGE('',*,*,#28650,.F.); -#28653=ORIENTED_EDGE('',*,*,#28652,.F.); -#28654=EDGE_LOOP('',(#28639,#28641,#28643,#28645,#28647,#28649,#28651,#28653)); -#28655=FACE_OUTER_BOUND('',#28654,.F.); -#28657=FILL_AREA_STYLE_COLOUR('',#17); -#28658=FILL_AREA_STYLE('',(#28657)); -#28659=SURFACE_STYLE_FILL_AREA(#28658); -#28660=SURFACE_SIDE_STYLE('',(#28659)); -#28661=SURFACE_STYLE_USAGE(.POSITIVE.,#28660); -#28662=PRESENTATION_STYLE_ASSIGNMENT((#28661)); -#28663=STYLED_ITEM('',(#28662),#28656); -#28664=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28665=DIRECTION('',(0.E0,1.E0,0.E0)); -#28666=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28667=AXIS2_PLACEMENT_3D('',#28664,#28665,#28666); -#28668=PLANE('',#28667); -#28670=ORIENTED_EDGE('',*,*,#28669,.F.); -#28672=ORIENTED_EDGE('',*,*,#28671,.F.); -#28674=ORIENTED_EDGE('',*,*,#28673,.F.); -#28676=ORIENTED_EDGE('',*,*,#28675,.F.); -#28678=ORIENTED_EDGE('',*,*,#28677,.F.); -#28680=ORIENTED_EDGE('',*,*,#28679,.F.); -#28682=ORIENTED_EDGE('',*,*,#28681,.F.); -#28684=ORIENTED_EDGE('',*,*,#28683,.F.); -#28686=ORIENTED_EDGE('',*,*,#28685,.F.); -#28688=ORIENTED_EDGE('',*,*,#28687,.F.); -#28690=ORIENTED_EDGE('',*,*,#28689,.F.); -#28692=ORIENTED_EDGE('',*,*,#28691,.F.); -#28694=ORIENTED_EDGE('',*,*,#28693,.F.); -#28696=ORIENTED_EDGE('',*,*,#28695,.F.); -#28698=ORIENTED_EDGE('',*,*,#28697,.F.); -#28700=ORIENTED_EDGE('',*,*,#28699,.F.); -#28702=ORIENTED_EDGE('',*,*,#28701,.F.); -#28704=ORIENTED_EDGE('',*,*,#28703,.F.); -#28706=ORIENTED_EDGE('',*,*,#28705,.F.); -#28708=ORIENTED_EDGE('',*,*,#28707,.F.); -#28710=ORIENTED_EDGE('',*,*,#28709,.F.); -#28712=ORIENTED_EDGE('',*,*,#28711,.F.); -#28714=ORIENTED_EDGE('',*,*,#28713,.F.); -#28716=ORIENTED_EDGE('',*,*,#28715,.F.); -#28718=ORIENTED_EDGE('',*,*,#28717,.F.); -#28720=ORIENTED_EDGE('',*,*,#28719,.F.); -#28722=ORIENTED_EDGE('',*,*,#28721,.F.); -#28724=ORIENTED_EDGE('',*,*,#28723,.F.); -#28726=ORIENTED_EDGE('',*,*,#28725,.F.); -#28728=ORIENTED_EDGE('',*,*,#28727,.F.); -#28730=ORIENTED_EDGE('',*,*,#28729,.F.); -#28732=ORIENTED_EDGE('',*,*,#28731,.F.); -#28734=ORIENTED_EDGE('',*,*,#28733,.F.); -#28736=ORIENTED_EDGE('',*,*,#28735,.F.); -#28737=EDGE_LOOP('',(#28670,#28672,#28674,#28676,#28678,#28680,#28682,#28684, -#28686,#28688,#28690,#28692,#28694,#28696,#28698,#28700,#28702,#28704,#28706, -#28708,#28710,#28712,#28714,#28716,#28718,#28720,#28722,#28724,#28726,#28728, -#28730,#28732,#28734,#28736)); -#28738=FACE_OUTER_BOUND('',#28737,.F.); -#28740=ORIENTED_EDGE('',*,*,#28739,.F.); -#28742=ORIENTED_EDGE('',*,*,#28741,.F.); -#28744=ORIENTED_EDGE('',*,*,#28743,.F.); -#28746=ORIENTED_EDGE('',*,*,#28745,.F.); -#28748=ORIENTED_EDGE('',*,*,#28747,.F.); -#28750=ORIENTED_EDGE('',*,*,#28749,.F.); -#28752=ORIENTED_EDGE('',*,*,#28751,.F.); -#28754=ORIENTED_EDGE('',*,*,#28753,.F.); -#28756=ORIENTED_EDGE('',*,*,#28755,.F.); -#28758=ORIENTED_EDGE('',*,*,#28757,.F.); -#28760=ORIENTED_EDGE('',*,*,#28759,.F.); -#28762=ORIENTED_EDGE('',*,*,#28761,.F.); -#28764=ORIENTED_EDGE('',*,*,#28763,.F.); -#28766=ORIENTED_EDGE('',*,*,#28765,.F.); -#28768=ORIENTED_EDGE('',*,*,#28767,.F.); -#28770=ORIENTED_EDGE('',*,*,#28769,.F.); -#28771=EDGE_LOOP('',(#28740,#28742,#28744,#28746,#28748,#28750,#28752,#28754, -#28756,#28758,#28760,#28762,#28764,#28766,#28768,#28770)); -#28772=FACE_BOUND('',#28771,.F.); -#28774=ORIENTED_EDGE('',*,*,#28773,.F.); -#28776=ORIENTED_EDGE('',*,*,#28775,.F.); -#28778=ORIENTED_EDGE('',*,*,#28777,.F.); -#28780=ORIENTED_EDGE('',*,*,#28779,.F.); -#28782=ORIENTED_EDGE('',*,*,#28781,.F.); -#28784=ORIENTED_EDGE('',*,*,#28783,.F.); -#28786=ORIENTED_EDGE('',*,*,#28785,.F.); -#28788=ORIENTED_EDGE('',*,*,#28787,.F.); -#28790=ORIENTED_EDGE('',*,*,#28789,.F.); -#28792=ORIENTED_EDGE('',*,*,#28791,.F.); -#28794=ORIENTED_EDGE('',*,*,#28793,.F.); -#28796=ORIENTED_EDGE('',*,*,#28795,.F.); -#28798=ORIENTED_EDGE('',*,*,#28797,.F.); -#28800=ORIENTED_EDGE('',*,*,#28799,.F.); -#28802=ORIENTED_EDGE('',*,*,#28801,.F.); -#28804=ORIENTED_EDGE('',*,*,#28803,.F.); -#28805=EDGE_LOOP('',(#28774,#28776,#28778,#28780,#28782,#28784,#28786,#28788, -#28790,#28792,#28794,#28796,#28798,#28800,#28802,#28804)); -#28806=FACE_BOUND('',#28805,.F.); -#28808=FILL_AREA_STYLE_COLOUR('',#17); -#28809=FILL_AREA_STYLE('',(#28808)); -#28810=SURFACE_STYLE_FILL_AREA(#28809); -#28811=SURFACE_SIDE_STYLE('',(#28810)); -#28812=SURFACE_STYLE_USAGE(.POSITIVE.,#28811); -#28813=PRESENTATION_STYLE_ASSIGNMENT((#28812)); -#28814=STYLED_ITEM('',(#28813),#28807); -#28815=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28816=DIRECTION('',(0.E0,1.E0,0.E0)); -#28817=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28818=AXIS2_PLACEMENT_3D('',#28815,#28816,#28817); -#28819=PLANE('',#28818); -#28821=ORIENTED_EDGE('',*,*,#28820,.F.); -#28823=ORIENTED_EDGE('',*,*,#28822,.F.); -#28825=ORIENTED_EDGE('',*,*,#28824,.F.); -#28827=ORIENTED_EDGE('',*,*,#28826,.F.); -#28829=ORIENTED_EDGE('',*,*,#28828,.F.); -#28831=ORIENTED_EDGE('',*,*,#28830,.F.); -#28833=ORIENTED_EDGE('',*,*,#28832,.F.); -#28835=ORIENTED_EDGE('',*,*,#28834,.F.); -#28837=ORIENTED_EDGE('',*,*,#28836,.F.); -#28839=ORIENTED_EDGE('',*,*,#28838,.F.); -#28841=ORIENTED_EDGE('',*,*,#28840,.F.); -#28843=ORIENTED_EDGE('',*,*,#28842,.F.); -#28845=ORIENTED_EDGE('',*,*,#28844,.F.); -#28847=ORIENTED_EDGE('',*,*,#28846,.F.); -#28849=ORIENTED_EDGE('',*,*,#28848,.F.); -#28851=ORIENTED_EDGE('',*,*,#28850,.F.); -#28853=ORIENTED_EDGE('',*,*,#28852,.F.); -#28855=ORIENTED_EDGE('',*,*,#28854,.F.); -#28857=ORIENTED_EDGE('',*,*,#28856,.F.); -#28859=ORIENTED_EDGE('',*,*,#28858,.F.); -#28861=ORIENTED_EDGE('',*,*,#28860,.F.); -#28863=ORIENTED_EDGE('',*,*,#28862,.F.); -#28865=ORIENTED_EDGE('',*,*,#28864,.F.); -#28867=ORIENTED_EDGE('',*,*,#28866,.F.); -#28869=ORIENTED_EDGE('',*,*,#28868,.F.); -#28871=ORIENTED_EDGE('',*,*,#28870,.F.); -#28873=ORIENTED_EDGE('',*,*,#28872,.F.); -#28875=ORIENTED_EDGE('',*,*,#28874,.F.); -#28877=ORIENTED_EDGE('',*,*,#28876,.F.); -#28879=ORIENTED_EDGE('',*,*,#28878,.F.); -#28881=ORIENTED_EDGE('',*,*,#28880,.F.); -#28883=ORIENTED_EDGE('',*,*,#28882,.F.); -#28885=ORIENTED_EDGE('',*,*,#28884,.F.); -#28887=ORIENTED_EDGE('',*,*,#28886,.F.); -#28889=ORIENTED_EDGE('',*,*,#28888,.F.); -#28891=ORIENTED_EDGE('',*,*,#28890,.F.); -#28893=ORIENTED_EDGE('',*,*,#28892,.F.); -#28895=ORIENTED_EDGE('',*,*,#28894,.F.); -#28897=ORIENTED_EDGE('',*,*,#28896,.F.); -#28899=ORIENTED_EDGE('',*,*,#28898,.F.); -#28901=ORIENTED_EDGE('',*,*,#28900,.F.); -#28903=ORIENTED_EDGE('',*,*,#28902,.F.); -#28905=ORIENTED_EDGE('',*,*,#28904,.F.); -#28907=ORIENTED_EDGE('',*,*,#28906,.F.); -#28909=ORIENTED_EDGE('',*,*,#28908,.F.); -#28911=ORIENTED_EDGE('',*,*,#28910,.F.); -#28913=ORIENTED_EDGE('',*,*,#28912,.F.); -#28915=ORIENTED_EDGE('',*,*,#28914,.F.); -#28917=ORIENTED_EDGE('',*,*,#28916,.F.); -#28919=ORIENTED_EDGE('',*,*,#28918,.F.); -#28921=ORIENTED_EDGE('',*,*,#28920,.F.); -#28923=ORIENTED_EDGE('',*,*,#28922,.F.); -#28925=ORIENTED_EDGE('',*,*,#28924,.F.); -#28927=ORIENTED_EDGE('',*,*,#28926,.F.); -#28929=ORIENTED_EDGE('',*,*,#28928,.F.); -#28931=ORIENTED_EDGE('',*,*,#28930,.F.); -#28933=ORIENTED_EDGE('',*,*,#28932,.F.); -#28934=EDGE_LOOP('',(#28821,#28823,#28825,#28827,#28829,#28831,#28833,#28835, -#28837,#28839,#28841,#28843,#28845,#28847,#28849,#28851,#28853,#28855,#28857, -#28859,#28861,#28863,#28865,#28867,#28869,#28871,#28873,#28875,#28877,#28879, -#28881,#28883,#28885,#28887,#28889,#28891,#28893,#28895,#28897,#28899,#28901, -#28903,#28905,#28907,#28909,#28911,#28913,#28915,#28917,#28919,#28921,#28923, -#28925,#28927,#28929,#28931,#28933)); -#28935=FACE_OUTER_BOUND('',#28934,.F.); -#28937=FILL_AREA_STYLE_COLOUR('',#17); -#28938=FILL_AREA_STYLE('',(#28937)); -#28939=SURFACE_STYLE_FILL_AREA(#28938); -#28940=SURFACE_SIDE_STYLE('',(#28939)); -#28941=SURFACE_STYLE_USAGE(.POSITIVE.,#28940); -#28942=PRESENTATION_STYLE_ASSIGNMENT((#28941)); -#28943=STYLED_ITEM('',(#28942),#28936); -#28944=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#28945=DIRECTION('',(0.E0,1.E0,0.E0)); -#28946=DIRECTION('',(0.E0,0.E0,-1.E0)); -#28947=AXIS2_PLACEMENT_3D('',#28944,#28945,#28946); -#28948=PLANE('',#28947); -#28950=ORIENTED_EDGE('',*,*,#28949,.F.); -#28952=ORIENTED_EDGE('',*,*,#28951,.F.); -#28954=ORIENTED_EDGE('',*,*,#28953,.F.); -#28956=ORIENTED_EDGE('',*,*,#28955,.F.); -#28958=ORIENTED_EDGE('',*,*,#28957,.F.); -#28960=ORIENTED_EDGE('',*,*,#28959,.F.); -#28962=ORIENTED_EDGE('',*,*,#28961,.F.); -#28964=ORIENTED_EDGE('',*,*,#28963,.F.); -#28966=ORIENTED_EDGE('',*,*,#28965,.F.); -#28968=ORIENTED_EDGE('',*,*,#28967,.F.); -#28970=ORIENTED_EDGE('',*,*,#28969,.F.); -#28972=ORIENTED_EDGE('',*,*,#28971,.F.); -#28974=ORIENTED_EDGE('',*,*,#28973,.F.); -#28976=ORIENTED_EDGE('',*,*,#28975,.F.); -#28978=ORIENTED_EDGE('',*,*,#28977,.F.); -#28980=ORIENTED_EDGE('',*,*,#28979,.F.); -#28982=ORIENTED_EDGE('',*,*,#28981,.F.); -#28984=ORIENTED_EDGE('',*,*,#28983,.F.); -#28986=ORIENTED_EDGE('',*,*,#28985,.F.); -#28988=ORIENTED_EDGE('',*,*,#28987,.F.); -#28990=ORIENTED_EDGE('',*,*,#28989,.F.); -#28992=ORIENTED_EDGE('',*,*,#28991,.F.); -#28994=ORIENTED_EDGE('',*,*,#28993,.F.); -#28996=ORIENTED_EDGE('',*,*,#28995,.F.); -#28998=ORIENTED_EDGE('',*,*,#28997,.F.); -#29000=ORIENTED_EDGE('',*,*,#28999,.F.); -#29002=ORIENTED_EDGE('',*,*,#29001,.F.); -#29004=ORIENTED_EDGE('',*,*,#29003,.F.); -#29005=EDGE_LOOP('',(#28950,#28952,#28954,#28956,#28958,#28960,#28962,#28964, -#28966,#28968,#28970,#28972,#28974,#28976,#28978,#28980,#28982,#28984,#28986, -#28988,#28990,#28992,#28994,#28996,#28998,#29000,#29002,#29004)); -#29006=FACE_OUTER_BOUND('',#29005,.F.); -#29008=FILL_AREA_STYLE_COLOUR('',#17); -#29009=FILL_AREA_STYLE('',(#29008)); -#29010=SURFACE_STYLE_FILL_AREA(#29009); -#29011=SURFACE_SIDE_STYLE('',(#29010)); -#29012=SURFACE_STYLE_USAGE(.POSITIVE.,#29011); -#29013=PRESENTATION_STYLE_ASSIGNMENT((#29012)); -#29014=STYLED_ITEM('',(#29013),#29007); -#29015=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29016=DIRECTION('',(0.E0,1.E0,0.E0)); -#29017=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29018=AXIS2_PLACEMENT_3D('',#29015,#29016,#29017); -#29019=PLANE('',#29018); -#29021=ORIENTED_EDGE('',*,*,#29020,.F.); -#29023=ORIENTED_EDGE('',*,*,#29022,.F.); -#29025=ORIENTED_EDGE('',*,*,#29024,.F.); -#29027=ORIENTED_EDGE('',*,*,#29026,.F.); -#29028=EDGE_LOOP('',(#29021,#29023,#29025,#29027)); -#29029=FACE_OUTER_BOUND('',#29028,.F.); -#29031=FILL_AREA_STYLE_COLOUR('',#17); -#29032=FILL_AREA_STYLE('',(#29031)); -#29033=SURFACE_STYLE_FILL_AREA(#29032); -#29034=SURFACE_SIDE_STYLE('',(#29033)); -#29035=SURFACE_STYLE_USAGE(.POSITIVE.,#29034); -#29036=PRESENTATION_STYLE_ASSIGNMENT((#29035)); -#29037=STYLED_ITEM('',(#29036),#29030); -#29038=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29039=DIRECTION('',(0.E0,1.E0,0.E0)); -#29040=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29041=AXIS2_PLACEMENT_3D('',#29038,#29039,#29040); -#29042=PLANE('',#29041); -#29044=ORIENTED_EDGE('',*,*,#29043,.F.); -#29046=ORIENTED_EDGE('',*,*,#29045,.F.); -#29048=ORIENTED_EDGE('',*,*,#29047,.F.); -#29050=ORIENTED_EDGE('',*,*,#29049,.F.); -#29052=ORIENTED_EDGE('',*,*,#29051,.F.); -#29054=ORIENTED_EDGE('',*,*,#29053,.F.); -#29056=ORIENTED_EDGE('',*,*,#29055,.F.); -#29058=ORIENTED_EDGE('',*,*,#29057,.F.); -#29060=ORIENTED_EDGE('',*,*,#29059,.F.); -#29062=ORIENTED_EDGE('',*,*,#29061,.F.); -#29064=ORIENTED_EDGE('',*,*,#29063,.F.); -#29066=ORIENTED_EDGE('',*,*,#29065,.F.); -#29068=ORIENTED_EDGE('',*,*,#29067,.F.); -#29070=ORIENTED_EDGE('',*,*,#29069,.F.); -#29072=ORIENTED_EDGE('',*,*,#29071,.F.); -#29074=ORIENTED_EDGE('',*,*,#29073,.F.); -#29076=ORIENTED_EDGE('',*,*,#29075,.F.); -#29078=ORIENTED_EDGE('',*,*,#29077,.F.); -#29080=ORIENTED_EDGE('',*,*,#29079,.F.); -#29082=ORIENTED_EDGE('',*,*,#29081,.F.); -#29084=ORIENTED_EDGE('',*,*,#29083,.F.); -#29086=ORIENTED_EDGE('',*,*,#29085,.F.); -#29088=ORIENTED_EDGE('',*,*,#29087,.F.); -#29090=ORIENTED_EDGE('',*,*,#29089,.F.); -#29092=ORIENTED_EDGE('',*,*,#29091,.F.); -#29094=ORIENTED_EDGE('',*,*,#29093,.F.); -#29096=ORIENTED_EDGE('',*,*,#29095,.F.); -#29098=ORIENTED_EDGE('',*,*,#29097,.F.); -#29100=ORIENTED_EDGE('',*,*,#29099,.F.); -#29102=ORIENTED_EDGE('',*,*,#29101,.F.); -#29104=ORIENTED_EDGE('',*,*,#29103,.F.); -#29106=ORIENTED_EDGE('',*,*,#29105,.F.); -#29108=ORIENTED_EDGE('',*,*,#29107,.F.); -#29110=ORIENTED_EDGE('',*,*,#29109,.F.); -#29112=ORIENTED_EDGE('',*,*,#29111,.F.); -#29114=ORIENTED_EDGE('',*,*,#29113,.F.); -#29116=ORIENTED_EDGE('',*,*,#29115,.F.); -#29118=ORIENTED_EDGE('',*,*,#29117,.F.); -#29120=ORIENTED_EDGE('',*,*,#29119,.F.); -#29122=ORIENTED_EDGE('',*,*,#29121,.F.); -#29123=EDGE_LOOP('',(#29044,#29046,#29048,#29050,#29052,#29054,#29056,#29058, -#29060,#29062,#29064,#29066,#29068,#29070,#29072,#29074,#29076,#29078,#29080, -#29082,#29084,#29086,#29088,#29090,#29092,#29094,#29096,#29098,#29100,#29102, -#29104,#29106,#29108,#29110,#29112,#29114,#29116,#29118,#29120,#29122)); -#29124=FACE_OUTER_BOUND('',#29123,.F.); -#29126=FILL_AREA_STYLE_COLOUR('',#17); -#29127=FILL_AREA_STYLE('',(#29126)); -#29128=SURFACE_STYLE_FILL_AREA(#29127); -#29129=SURFACE_SIDE_STYLE('',(#29128)); -#29130=SURFACE_STYLE_USAGE(.POSITIVE.,#29129); -#29131=PRESENTATION_STYLE_ASSIGNMENT((#29130)); -#29132=STYLED_ITEM('',(#29131),#29125); -#29133=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29134=DIRECTION('',(0.E0,1.E0,0.E0)); -#29135=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29136=AXIS2_PLACEMENT_3D('',#29133,#29134,#29135); -#29137=PLANE('',#29136); -#29139=ORIENTED_EDGE('',*,*,#29138,.F.); -#29141=ORIENTED_EDGE('',*,*,#29140,.F.); -#29143=ORIENTED_EDGE('',*,*,#29142,.F.); -#29145=ORIENTED_EDGE('',*,*,#29144,.F.); -#29146=EDGE_LOOP('',(#29139,#29141,#29143,#29145)); -#29147=FACE_OUTER_BOUND('',#29146,.F.); -#29149=FILL_AREA_STYLE_COLOUR('',#17); -#29150=FILL_AREA_STYLE('',(#29149)); -#29151=SURFACE_STYLE_FILL_AREA(#29150); -#29152=SURFACE_SIDE_STYLE('',(#29151)); -#29153=SURFACE_STYLE_USAGE(.POSITIVE.,#29152); -#29154=PRESENTATION_STYLE_ASSIGNMENT((#29153)); -#29155=STYLED_ITEM('',(#29154),#29148); -#29156=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29157=DIRECTION('',(0.E0,1.E0,0.E0)); -#29158=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29159=AXIS2_PLACEMENT_3D('',#29156,#29157,#29158); -#29160=PLANE('',#29159); -#29162=ORIENTED_EDGE('',*,*,#29161,.F.); -#29164=ORIENTED_EDGE('',*,*,#29163,.F.); -#29166=ORIENTED_EDGE('',*,*,#29165,.F.); -#29168=ORIENTED_EDGE('',*,*,#29167,.F.); -#29170=ORIENTED_EDGE('',*,*,#29169,.F.); -#29172=ORIENTED_EDGE('',*,*,#29171,.F.); -#29174=ORIENTED_EDGE('',*,*,#29173,.F.); -#29176=ORIENTED_EDGE('',*,*,#29175,.F.); -#29178=ORIENTED_EDGE('',*,*,#29177,.F.); -#29180=ORIENTED_EDGE('',*,*,#29179,.F.); -#29182=ORIENTED_EDGE('',*,*,#29181,.F.); -#29184=ORIENTED_EDGE('',*,*,#29183,.F.); -#29186=ORIENTED_EDGE('',*,*,#29185,.F.); -#29188=ORIENTED_EDGE('',*,*,#29187,.F.); -#29189=EDGE_LOOP('',(#29162,#29164,#29166,#29168,#29170,#29172,#29174,#29176, -#29178,#29180,#29182,#29184,#29186,#29188)); -#29190=FACE_OUTER_BOUND('',#29189,.F.); -#29192=ORIENTED_EDGE('',*,*,#29191,.F.); -#29194=ORIENTED_EDGE('',*,*,#29193,.F.); -#29196=ORIENTED_EDGE('',*,*,#29195,.F.); -#29198=ORIENTED_EDGE('',*,*,#29197,.F.); -#29200=ORIENTED_EDGE('',*,*,#29199,.F.); -#29202=ORIENTED_EDGE('',*,*,#29201,.F.); -#29204=ORIENTED_EDGE('',*,*,#29203,.F.); -#29206=ORIENTED_EDGE('',*,*,#29205,.F.); -#29208=ORIENTED_EDGE('',*,*,#29207,.F.); -#29210=ORIENTED_EDGE('',*,*,#29209,.F.); -#29212=ORIENTED_EDGE('',*,*,#29211,.F.); -#29214=ORIENTED_EDGE('',*,*,#29213,.F.); -#29215=EDGE_LOOP('',(#29192,#29194,#29196,#29198,#29200,#29202,#29204,#29206, -#29208,#29210,#29212,#29214)); -#29216=FACE_BOUND('',#29215,.F.); -#29218=FILL_AREA_STYLE_COLOUR('',#17); -#29219=FILL_AREA_STYLE('',(#29218)); -#29220=SURFACE_STYLE_FILL_AREA(#29219); -#29221=SURFACE_SIDE_STYLE('',(#29220)); -#29222=SURFACE_STYLE_USAGE(.POSITIVE.,#29221); -#29223=PRESENTATION_STYLE_ASSIGNMENT((#29222)); -#29224=STYLED_ITEM('',(#29223),#29217); -#29225=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29226=DIRECTION('',(0.E0,1.E0,0.E0)); -#29227=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29228=AXIS2_PLACEMENT_3D('',#29225,#29226,#29227); -#29229=PLANE('',#29228); -#29231=ORIENTED_EDGE('',*,*,#29230,.F.); -#29233=ORIENTED_EDGE('',*,*,#29232,.F.); -#29235=ORIENTED_EDGE('',*,*,#29234,.F.); -#29237=ORIENTED_EDGE('',*,*,#29236,.F.); -#29238=EDGE_LOOP('',(#29231,#29233,#29235,#29237)); -#29239=FACE_OUTER_BOUND('',#29238,.F.); -#29241=FILL_AREA_STYLE_COLOUR('',#17); -#29242=FILL_AREA_STYLE('',(#29241)); -#29243=SURFACE_STYLE_FILL_AREA(#29242); -#29244=SURFACE_SIDE_STYLE('',(#29243)); -#29245=SURFACE_STYLE_USAGE(.POSITIVE.,#29244); -#29246=PRESENTATION_STYLE_ASSIGNMENT((#29245)); -#29247=STYLED_ITEM('',(#29246),#29240); -#29248=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29249=DIRECTION('',(0.E0,1.E0,0.E0)); -#29250=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29251=AXIS2_PLACEMENT_3D('',#29248,#29249,#29250); -#29252=PLANE('',#29251); -#29254=ORIENTED_EDGE('',*,*,#29253,.F.); -#29256=ORIENTED_EDGE('',*,*,#29255,.F.); -#29258=ORIENTED_EDGE('',*,*,#29257,.F.); -#29260=ORIENTED_EDGE('',*,*,#29259,.F.); -#29261=EDGE_LOOP('',(#29254,#29256,#29258,#29260)); -#29262=FACE_OUTER_BOUND('',#29261,.F.); -#29264=FILL_AREA_STYLE_COLOUR('',#17); -#29265=FILL_AREA_STYLE('',(#29264)); -#29266=SURFACE_STYLE_FILL_AREA(#29265); -#29267=SURFACE_SIDE_STYLE('',(#29266)); -#29268=SURFACE_STYLE_USAGE(.POSITIVE.,#29267); -#29269=PRESENTATION_STYLE_ASSIGNMENT((#29268)); -#29270=STYLED_ITEM('',(#29269),#29263); -#29271=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29272=DIRECTION('',(0.E0,1.E0,0.E0)); -#29273=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29274=AXIS2_PLACEMENT_3D('',#29271,#29272,#29273); -#29275=PLANE('',#29274); -#29277=ORIENTED_EDGE('',*,*,#29276,.F.); -#29279=ORIENTED_EDGE('',*,*,#29278,.F.); -#29281=ORIENTED_EDGE('',*,*,#29280,.F.); -#29283=ORIENTED_EDGE('',*,*,#29282,.F.); -#29285=ORIENTED_EDGE('',*,*,#29284,.F.); -#29287=ORIENTED_EDGE('',*,*,#29286,.F.); -#29289=ORIENTED_EDGE('',*,*,#29288,.F.); -#29291=ORIENTED_EDGE('',*,*,#29290,.F.); -#29293=ORIENTED_EDGE('',*,*,#29292,.F.); -#29295=ORIENTED_EDGE('',*,*,#29294,.F.); -#29297=ORIENTED_EDGE('',*,*,#29296,.F.); -#29298=EDGE_LOOP('',(#29277,#29279,#29281,#29283,#29285,#29287,#29289,#29291, -#29293,#29295,#29297)); -#29299=FACE_OUTER_BOUND('',#29298,.F.); -#29301=ORIENTED_EDGE('',*,*,#29300,.F.); -#29303=ORIENTED_EDGE('',*,*,#29302,.F.); -#29305=ORIENTED_EDGE('',*,*,#29304,.F.); -#29306=EDGE_LOOP('',(#29301,#29303,#29305)); -#29307=FACE_BOUND('',#29306,.F.); -#29309=FILL_AREA_STYLE_COLOUR('',#17); -#29310=FILL_AREA_STYLE('',(#29309)); -#29311=SURFACE_STYLE_FILL_AREA(#29310); -#29312=SURFACE_SIDE_STYLE('',(#29311)); -#29313=SURFACE_STYLE_USAGE(.POSITIVE.,#29312); -#29314=PRESENTATION_STYLE_ASSIGNMENT((#29313)); -#29315=STYLED_ITEM('',(#29314),#29308); -#29316=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29317=DIRECTION('',(0.E0,1.E0,0.E0)); -#29318=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29319=AXIS2_PLACEMENT_3D('',#29316,#29317,#29318); -#29320=PLANE('',#29319); -#29322=ORIENTED_EDGE('',*,*,#29321,.F.); -#29324=ORIENTED_EDGE('',*,*,#29323,.F.); -#29326=ORIENTED_EDGE('',*,*,#29325,.F.); -#29328=ORIENTED_EDGE('',*,*,#29327,.F.); -#29330=ORIENTED_EDGE('',*,*,#29329,.F.); -#29332=ORIENTED_EDGE('',*,*,#29331,.F.); -#29334=ORIENTED_EDGE('',*,*,#29333,.F.); -#29335=EDGE_LOOP('',(#29322,#29324,#29326,#29328,#29330,#29332,#29334)); -#29336=FACE_OUTER_BOUND('',#29335,.F.); -#29338=FILL_AREA_STYLE_COLOUR('',#17); -#29339=FILL_AREA_STYLE('',(#29338)); -#29340=SURFACE_STYLE_FILL_AREA(#29339); -#29341=SURFACE_SIDE_STYLE('',(#29340)); -#29342=SURFACE_STYLE_USAGE(.POSITIVE.,#29341); -#29343=PRESENTATION_STYLE_ASSIGNMENT((#29342)); -#29344=STYLED_ITEM('',(#29343),#29337); -#29345=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29346=DIRECTION('',(0.E0,1.E0,0.E0)); -#29347=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29348=AXIS2_PLACEMENT_3D('',#29345,#29346,#29347); -#29349=PLANE('',#29348); -#29351=ORIENTED_EDGE('',*,*,#29350,.F.); -#29353=ORIENTED_EDGE('',*,*,#29352,.F.); -#29355=ORIENTED_EDGE('',*,*,#29354,.F.); -#29357=ORIENTED_EDGE('',*,*,#29356,.F.); -#29359=ORIENTED_EDGE('',*,*,#29358,.F.); -#29361=ORIENTED_EDGE('',*,*,#29360,.F.); -#29363=ORIENTED_EDGE('',*,*,#29362,.F.); -#29365=ORIENTED_EDGE('',*,*,#29364,.F.); -#29367=ORIENTED_EDGE('',*,*,#29366,.F.); -#29369=ORIENTED_EDGE('',*,*,#29368,.F.); -#29371=ORIENTED_EDGE('',*,*,#29370,.F.); -#29373=ORIENTED_EDGE('',*,*,#29372,.F.); -#29375=ORIENTED_EDGE('',*,*,#29374,.F.); -#29377=ORIENTED_EDGE('',*,*,#29376,.F.); -#29379=ORIENTED_EDGE('',*,*,#29378,.F.); -#29381=ORIENTED_EDGE('',*,*,#29380,.F.); -#29383=ORIENTED_EDGE('',*,*,#29382,.F.); -#29385=ORIENTED_EDGE('',*,*,#29384,.F.); -#29387=ORIENTED_EDGE('',*,*,#29386,.F.); -#29389=ORIENTED_EDGE('',*,*,#29388,.F.); -#29391=ORIENTED_EDGE('',*,*,#29390,.F.); -#29393=ORIENTED_EDGE('',*,*,#29392,.F.); -#29395=ORIENTED_EDGE('',*,*,#29394,.F.); -#29397=ORIENTED_EDGE('',*,*,#29396,.F.); -#29399=ORIENTED_EDGE('',*,*,#29398,.F.); -#29401=ORIENTED_EDGE('',*,*,#29400,.F.); -#29402=EDGE_LOOP('',(#29351,#29353,#29355,#29357,#29359,#29361,#29363,#29365, -#29367,#29369,#29371,#29373,#29375,#29377,#29379,#29381,#29383,#29385,#29387, -#29389,#29391,#29393,#29395,#29397,#29399,#29401)); -#29403=FACE_OUTER_BOUND('',#29402,.F.); -#29405=ORIENTED_EDGE('',*,*,#29404,.F.); -#29407=ORIENTED_EDGE('',*,*,#29406,.F.); -#29409=ORIENTED_EDGE('',*,*,#29408,.F.); -#29411=ORIENTED_EDGE('',*,*,#29410,.F.); -#29413=ORIENTED_EDGE('',*,*,#29412,.F.); -#29415=ORIENTED_EDGE('',*,*,#29414,.F.); -#29417=ORIENTED_EDGE('',*,*,#29416,.F.); -#29419=ORIENTED_EDGE('',*,*,#29418,.F.); -#29421=ORIENTED_EDGE('',*,*,#29420,.F.); -#29423=ORIENTED_EDGE('',*,*,#29422,.F.); -#29425=ORIENTED_EDGE('',*,*,#29424,.F.); -#29427=ORIENTED_EDGE('',*,*,#29426,.F.); -#29429=ORIENTED_EDGE('',*,*,#29428,.F.); -#29431=ORIENTED_EDGE('',*,*,#29430,.F.); -#29433=ORIENTED_EDGE('',*,*,#29432,.F.); -#29435=ORIENTED_EDGE('',*,*,#29434,.F.); -#29437=ORIENTED_EDGE('',*,*,#29436,.F.); -#29439=ORIENTED_EDGE('',*,*,#29438,.F.); -#29440=EDGE_LOOP('',(#29405,#29407,#29409,#29411,#29413,#29415,#29417,#29419, -#29421,#29423,#29425,#29427,#29429,#29431,#29433,#29435,#29437,#29439)); -#29441=FACE_BOUND('',#29440,.F.); -#29443=FILL_AREA_STYLE_COLOUR('',#17); -#29444=FILL_AREA_STYLE('',(#29443)); -#29445=SURFACE_STYLE_FILL_AREA(#29444); -#29446=SURFACE_SIDE_STYLE('',(#29445)); -#29447=SURFACE_STYLE_USAGE(.POSITIVE.,#29446); -#29448=PRESENTATION_STYLE_ASSIGNMENT((#29447)); -#29449=STYLED_ITEM('',(#29448),#29442); -#29450=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29451=DIRECTION('',(0.E0,1.E0,0.E0)); -#29452=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29453=AXIS2_PLACEMENT_3D('',#29450,#29451,#29452); -#29454=PLANE('',#29453); -#29456=ORIENTED_EDGE('',*,*,#29455,.F.); -#29458=ORIENTED_EDGE('',*,*,#29457,.F.); -#29460=ORIENTED_EDGE('',*,*,#29459,.F.); -#29462=ORIENTED_EDGE('',*,*,#29461,.F.); -#29464=ORIENTED_EDGE('',*,*,#29463,.F.); -#29466=ORIENTED_EDGE('',*,*,#29465,.F.); -#29468=ORIENTED_EDGE('',*,*,#29467,.F.); -#29470=ORIENTED_EDGE('',*,*,#29469,.F.); -#29472=ORIENTED_EDGE('',*,*,#29471,.F.); -#29474=ORIENTED_EDGE('',*,*,#29473,.F.); -#29476=ORIENTED_EDGE('',*,*,#29475,.F.); -#29478=ORIENTED_EDGE('',*,*,#29477,.F.); -#29480=ORIENTED_EDGE('',*,*,#29479,.F.); -#29482=ORIENTED_EDGE('',*,*,#29481,.F.); -#29484=ORIENTED_EDGE('',*,*,#29483,.F.); -#29486=ORIENTED_EDGE('',*,*,#29485,.F.); -#29488=ORIENTED_EDGE('',*,*,#29487,.F.); -#29490=ORIENTED_EDGE('',*,*,#29489,.F.); -#29492=ORIENTED_EDGE('',*,*,#29491,.F.); -#29494=ORIENTED_EDGE('',*,*,#29493,.F.); -#29496=ORIENTED_EDGE('',*,*,#29495,.F.); -#29498=ORIENTED_EDGE('',*,*,#29497,.F.); -#29500=ORIENTED_EDGE('',*,*,#29499,.F.); -#29502=ORIENTED_EDGE('',*,*,#29501,.F.); -#29504=ORIENTED_EDGE('',*,*,#29503,.F.); -#29506=ORIENTED_EDGE('',*,*,#29505,.F.); -#29507=EDGE_LOOP('',(#29456,#29458,#29460,#29462,#29464,#29466,#29468,#29470, -#29472,#29474,#29476,#29478,#29480,#29482,#29484,#29486,#29488,#29490,#29492, -#29494,#29496,#29498,#29500,#29502,#29504,#29506)); -#29508=FACE_OUTER_BOUND('',#29507,.F.); -#29510=ORIENTED_EDGE('',*,*,#29509,.F.); -#29512=ORIENTED_EDGE('',*,*,#29511,.F.); -#29514=ORIENTED_EDGE('',*,*,#29513,.F.); -#29516=ORIENTED_EDGE('',*,*,#29515,.F.); -#29518=ORIENTED_EDGE('',*,*,#29517,.F.); -#29520=ORIENTED_EDGE('',*,*,#29519,.F.); -#29522=ORIENTED_EDGE('',*,*,#29521,.F.); -#29524=ORIENTED_EDGE('',*,*,#29523,.F.); -#29526=ORIENTED_EDGE('',*,*,#29525,.F.); -#29528=ORIENTED_EDGE('',*,*,#29527,.F.); -#29530=ORIENTED_EDGE('',*,*,#29529,.F.); -#29532=ORIENTED_EDGE('',*,*,#29531,.F.); -#29534=ORIENTED_EDGE('',*,*,#29533,.F.); -#29536=ORIENTED_EDGE('',*,*,#29535,.F.); -#29538=ORIENTED_EDGE('',*,*,#29537,.F.); -#29540=ORIENTED_EDGE('',*,*,#29539,.F.); -#29542=ORIENTED_EDGE('',*,*,#29541,.F.); -#29544=ORIENTED_EDGE('',*,*,#29543,.F.); -#29545=EDGE_LOOP('',(#29510,#29512,#29514,#29516,#29518,#29520,#29522,#29524, -#29526,#29528,#29530,#29532,#29534,#29536,#29538,#29540,#29542,#29544)); -#29546=FACE_BOUND('',#29545,.F.); -#29548=FILL_AREA_STYLE_COLOUR('',#17); -#29549=FILL_AREA_STYLE('',(#29548)); -#29550=SURFACE_STYLE_FILL_AREA(#29549); -#29551=SURFACE_SIDE_STYLE('',(#29550)); -#29552=SURFACE_STYLE_USAGE(.POSITIVE.,#29551); -#29553=PRESENTATION_STYLE_ASSIGNMENT((#29552)); -#29554=STYLED_ITEM('',(#29553),#29547); -#29555=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29556=DIRECTION('',(0.E0,1.E0,0.E0)); -#29557=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29558=AXIS2_PLACEMENT_3D('',#29555,#29556,#29557); -#29559=PLANE('',#29558); -#29561=ORIENTED_EDGE('',*,*,#29560,.F.); -#29563=ORIENTED_EDGE('',*,*,#29562,.F.); -#29565=ORIENTED_EDGE('',*,*,#29564,.F.); -#29567=ORIENTED_EDGE('',*,*,#29566,.F.); -#29569=ORIENTED_EDGE('',*,*,#29568,.F.); -#29571=ORIENTED_EDGE('',*,*,#29570,.F.); -#29573=ORIENTED_EDGE('',*,*,#29572,.F.); -#29575=ORIENTED_EDGE('',*,*,#29574,.F.); -#29576=EDGE_LOOP('',(#29561,#29563,#29565,#29567,#29569,#29571,#29573,#29575)); -#29577=FACE_OUTER_BOUND('',#29576,.F.); -#29579=ORIENTED_EDGE('',*,*,#29578,.F.); -#29581=ORIENTED_EDGE('',*,*,#29580,.F.); -#29583=ORIENTED_EDGE('',*,*,#29582,.F.); -#29584=EDGE_LOOP('',(#29579,#29581,#29583)); -#29585=FACE_BOUND('',#29584,.F.); -#29587=FILL_AREA_STYLE_COLOUR('',#17); -#29588=FILL_AREA_STYLE('',(#29587)); -#29589=SURFACE_STYLE_FILL_AREA(#29588); -#29590=SURFACE_SIDE_STYLE('',(#29589)); -#29591=SURFACE_STYLE_USAGE(.POSITIVE.,#29590); -#29592=PRESENTATION_STYLE_ASSIGNMENT((#29591)); -#29593=STYLED_ITEM('',(#29592),#29586); -#29594=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29595=DIRECTION('',(0.E0,1.E0,0.E0)); -#29596=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29597=AXIS2_PLACEMENT_3D('',#29594,#29595,#29596); -#29598=PLANE('',#29597); -#29600=ORIENTED_EDGE('',*,*,#29599,.F.); -#29602=ORIENTED_EDGE('',*,*,#29601,.F.); -#29604=ORIENTED_EDGE('',*,*,#29603,.F.); -#29606=ORIENTED_EDGE('',*,*,#29605,.F.); -#29607=EDGE_LOOP('',(#29600,#29602,#29604,#29606)); -#29608=FACE_OUTER_BOUND('',#29607,.F.); -#29610=FILL_AREA_STYLE_COLOUR('',#17); -#29611=FILL_AREA_STYLE('',(#29610)); -#29612=SURFACE_STYLE_FILL_AREA(#29611); -#29613=SURFACE_SIDE_STYLE('',(#29612)); -#29614=SURFACE_STYLE_USAGE(.POSITIVE.,#29613); -#29615=PRESENTATION_STYLE_ASSIGNMENT((#29614)); -#29616=STYLED_ITEM('',(#29615),#29609); -#29617=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29618=DIRECTION('',(0.E0,1.E0,0.E0)); -#29619=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29620=AXIS2_PLACEMENT_3D('',#29617,#29618,#29619); -#29621=PLANE('',#29620); -#29623=ORIENTED_EDGE('',*,*,#29622,.F.); -#29625=ORIENTED_EDGE('',*,*,#29624,.F.); -#29627=ORIENTED_EDGE('',*,*,#29626,.F.); -#29629=ORIENTED_EDGE('',*,*,#29628,.F.); -#29631=ORIENTED_EDGE('',*,*,#29630,.F.); -#29633=ORIENTED_EDGE('',*,*,#29632,.F.); -#29635=ORIENTED_EDGE('',*,*,#29634,.F.); -#29637=ORIENTED_EDGE('',*,*,#29636,.F.); -#29639=ORIENTED_EDGE('',*,*,#29638,.F.); -#29641=ORIENTED_EDGE('',*,*,#29640,.F.); -#29643=ORIENTED_EDGE('',*,*,#29642,.F.); -#29645=ORIENTED_EDGE('',*,*,#29644,.F.); -#29647=ORIENTED_EDGE('',*,*,#29646,.F.); -#29649=ORIENTED_EDGE('',*,*,#29648,.F.); -#29651=ORIENTED_EDGE('',*,*,#29650,.F.); -#29653=ORIENTED_EDGE('',*,*,#29652,.F.); -#29655=ORIENTED_EDGE('',*,*,#29654,.F.); -#29657=ORIENTED_EDGE('',*,*,#29656,.F.); -#29659=ORIENTED_EDGE('',*,*,#29658,.F.); -#29660=EDGE_LOOP('',(#29623,#29625,#29627,#29629,#29631,#29633,#29635,#29637, -#29639,#29641,#29643,#29645,#29647,#29649,#29651,#29653,#29655,#29657,#29659)); -#29661=FACE_OUTER_BOUND('',#29660,.F.); -#29663=ORIENTED_EDGE('',*,*,#29662,.F.); -#29665=ORIENTED_EDGE('',*,*,#29664,.F.); -#29667=ORIENTED_EDGE('',*,*,#29666,.F.); -#29669=ORIENTED_EDGE('',*,*,#29668,.F.); -#29671=ORIENTED_EDGE('',*,*,#29670,.F.); -#29673=ORIENTED_EDGE('',*,*,#29672,.F.); -#29675=ORIENTED_EDGE('',*,*,#29674,.F.); -#29677=ORIENTED_EDGE('',*,*,#29676,.F.); -#29679=ORIENTED_EDGE('',*,*,#29678,.F.); -#29681=ORIENTED_EDGE('',*,*,#29680,.F.); -#29682=EDGE_LOOP('',(#29663,#29665,#29667,#29669,#29671,#29673,#29675,#29677, -#29679,#29681)); -#29683=FACE_BOUND('',#29682,.F.); -#29685=ORIENTED_EDGE('',*,*,#29684,.F.); -#29687=ORIENTED_EDGE('',*,*,#29686,.F.); -#29689=ORIENTED_EDGE('',*,*,#29688,.F.); -#29691=ORIENTED_EDGE('',*,*,#29690,.F.); -#29693=ORIENTED_EDGE('',*,*,#29692,.F.); -#29695=ORIENTED_EDGE('',*,*,#29694,.F.); -#29697=ORIENTED_EDGE('',*,*,#29696,.F.); -#29699=ORIENTED_EDGE('',*,*,#29698,.F.); -#29701=ORIENTED_EDGE('',*,*,#29700,.F.); -#29703=ORIENTED_EDGE('',*,*,#29702,.F.); -#29704=EDGE_LOOP('',(#29685,#29687,#29689,#29691,#29693,#29695,#29697,#29699, -#29701,#29703)); -#29705=FACE_BOUND('',#29704,.F.); -#29707=FILL_AREA_STYLE_COLOUR('',#17); -#29708=FILL_AREA_STYLE('',(#29707)); -#29709=SURFACE_STYLE_FILL_AREA(#29708); -#29710=SURFACE_SIDE_STYLE('',(#29709)); -#29711=SURFACE_STYLE_USAGE(.POSITIVE.,#29710); -#29712=PRESENTATION_STYLE_ASSIGNMENT((#29711)); -#29713=STYLED_ITEM('',(#29712),#29706); -#29714=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29715=DIRECTION('',(0.E0,1.E0,0.E0)); -#29716=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29717=AXIS2_PLACEMENT_3D('',#29714,#29715,#29716); -#29718=PLANE('',#29717); -#29720=ORIENTED_EDGE('',*,*,#29719,.F.); -#29722=ORIENTED_EDGE('',*,*,#29721,.F.); -#29724=ORIENTED_EDGE('',*,*,#29723,.F.); -#29726=ORIENTED_EDGE('',*,*,#29725,.F.); -#29728=ORIENTED_EDGE('',*,*,#29727,.F.); -#29730=ORIENTED_EDGE('',*,*,#29729,.F.); -#29732=ORIENTED_EDGE('',*,*,#29731,.F.); -#29734=ORIENTED_EDGE('',*,*,#29733,.F.); -#29735=EDGE_LOOP('',(#29720,#29722,#29724,#29726,#29728,#29730,#29732,#29734)); -#29736=FACE_OUTER_BOUND('',#29735,.F.); -#29738=FILL_AREA_STYLE_COLOUR('',#17); -#29739=FILL_AREA_STYLE('',(#29738)); -#29740=SURFACE_STYLE_FILL_AREA(#29739); -#29741=SURFACE_SIDE_STYLE('',(#29740)); -#29742=SURFACE_STYLE_USAGE(.POSITIVE.,#29741); -#29743=PRESENTATION_STYLE_ASSIGNMENT((#29742)); -#29744=STYLED_ITEM('',(#29743),#29737); -#29745=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29746=DIRECTION('',(0.E0,1.E0,0.E0)); -#29747=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29748=AXIS2_PLACEMENT_3D('',#29745,#29746,#29747); -#29749=PLANE('',#29748); -#29751=ORIENTED_EDGE('',*,*,#29750,.F.); -#29753=ORIENTED_EDGE('',*,*,#29752,.F.); -#29755=ORIENTED_EDGE('',*,*,#29754,.F.); -#29757=ORIENTED_EDGE('',*,*,#29756,.F.); -#29759=ORIENTED_EDGE('',*,*,#29758,.F.); -#29761=ORIENTED_EDGE('',*,*,#29760,.F.); -#29763=ORIENTED_EDGE('',*,*,#29762,.F.); -#29765=ORIENTED_EDGE('',*,*,#29764,.F.); -#29767=ORIENTED_EDGE('',*,*,#29766,.F.); -#29769=ORIENTED_EDGE('',*,*,#29768,.F.); -#29771=ORIENTED_EDGE('',*,*,#29770,.F.); -#29773=ORIENTED_EDGE('',*,*,#29772,.F.); -#29775=ORIENTED_EDGE('',*,*,#29774,.F.); -#29777=ORIENTED_EDGE('',*,*,#29776,.F.); -#29779=ORIENTED_EDGE('',*,*,#29778,.F.); -#29781=ORIENTED_EDGE('',*,*,#29780,.F.); -#29783=ORIENTED_EDGE('',*,*,#29782,.F.); -#29785=ORIENTED_EDGE('',*,*,#29784,.F.); -#29787=ORIENTED_EDGE('',*,*,#29786,.F.); -#29789=ORIENTED_EDGE('',*,*,#29788,.F.); -#29791=ORIENTED_EDGE('',*,*,#29790,.F.); -#29793=ORIENTED_EDGE('',*,*,#29792,.F.); -#29795=ORIENTED_EDGE('',*,*,#29794,.F.); -#29797=ORIENTED_EDGE('',*,*,#29796,.F.); -#29799=ORIENTED_EDGE('',*,*,#29798,.F.); -#29801=ORIENTED_EDGE('',*,*,#29800,.F.); -#29803=ORIENTED_EDGE('',*,*,#29802,.F.); -#29805=ORIENTED_EDGE('',*,*,#29804,.F.); -#29807=ORIENTED_EDGE('',*,*,#29806,.F.); -#29809=ORIENTED_EDGE('',*,*,#29808,.F.); -#29811=ORIENTED_EDGE('',*,*,#29810,.F.); -#29813=ORIENTED_EDGE('',*,*,#29812,.F.); -#29815=ORIENTED_EDGE('',*,*,#29814,.F.); -#29817=ORIENTED_EDGE('',*,*,#29816,.F.); -#29818=EDGE_LOOP('',(#29751,#29753,#29755,#29757,#29759,#29761,#29763,#29765, -#29767,#29769,#29771,#29773,#29775,#29777,#29779,#29781,#29783,#29785,#29787, -#29789,#29791,#29793,#29795,#29797,#29799,#29801,#29803,#29805,#29807,#29809, -#29811,#29813,#29815,#29817)); -#29819=FACE_OUTER_BOUND('',#29818,.F.); -#29821=ORIENTED_EDGE('',*,*,#29820,.F.); -#29823=ORIENTED_EDGE('',*,*,#29822,.F.); -#29825=ORIENTED_EDGE('',*,*,#29824,.F.); -#29827=ORIENTED_EDGE('',*,*,#29826,.F.); -#29829=ORIENTED_EDGE('',*,*,#29828,.F.); -#29831=ORIENTED_EDGE('',*,*,#29830,.F.); -#29833=ORIENTED_EDGE('',*,*,#29832,.F.); -#29835=ORIENTED_EDGE('',*,*,#29834,.F.); -#29837=ORIENTED_EDGE('',*,*,#29836,.F.); -#29839=ORIENTED_EDGE('',*,*,#29838,.F.); -#29841=ORIENTED_EDGE('',*,*,#29840,.F.); -#29843=ORIENTED_EDGE('',*,*,#29842,.F.); -#29845=ORIENTED_EDGE('',*,*,#29844,.F.); -#29847=ORIENTED_EDGE('',*,*,#29846,.F.); -#29849=ORIENTED_EDGE('',*,*,#29848,.F.); -#29851=ORIENTED_EDGE('',*,*,#29850,.F.); -#29852=EDGE_LOOP('',(#29821,#29823,#29825,#29827,#29829,#29831,#29833,#29835, -#29837,#29839,#29841,#29843,#29845,#29847,#29849,#29851)); -#29853=FACE_BOUND('',#29852,.F.); -#29855=ORIENTED_EDGE('',*,*,#29854,.F.); -#29857=ORIENTED_EDGE('',*,*,#29856,.F.); -#29859=ORIENTED_EDGE('',*,*,#29858,.F.); -#29861=ORIENTED_EDGE('',*,*,#29860,.F.); -#29863=ORIENTED_EDGE('',*,*,#29862,.F.); -#29865=ORIENTED_EDGE('',*,*,#29864,.F.); -#29867=ORIENTED_EDGE('',*,*,#29866,.F.); -#29869=ORIENTED_EDGE('',*,*,#29868,.F.); -#29871=ORIENTED_EDGE('',*,*,#29870,.F.); -#29873=ORIENTED_EDGE('',*,*,#29872,.F.); -#29875=ORIENTED_EDGE('',*,*,#29874,.F.); -#29877=ORIENTED_EDGE('',*,*,#29876,.F.); -#29879=ORIENTED_EDGE('',*,*,#29878,.F.); -#29881=ORIENTED_EDGE('',*,*,#29880,.F.); -#29883=ORIENTED_EDGE('',*,*,#29882,.F.); -#29885=ORIENTED_EDGE('',*,*,#29884,.F.); -#29886=EDGE_LOOP('',(#29855,#29857,#29859,#29861,#29863,#29865,#29867,#29869, -#29871,#29873,#29875,#29877,#29879,#29881,#29883,#29885)); -#29887=FACE_BOUND('',#29886,.F.); -#29889=FILL_AREA_STYLE_COLOUR('',#17); -#29890=FILL_AREA_STYLE('',(#29889)); -#29891=SURFACE_STYLE_FILL_AREA(#29890); -#29892=SURFACE_SIDE_STYLE('',(#29891)); -#29893=SURFACE_STYLE_USAGE(.POSITIVE.,#29892); -#29894=PRESENTATION_STYLE_ASSIGNMENT((#29893)); -#29895=STYLED_ITEM('',(#29894),#29888); -#29896=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#29897=DIRECTION('',(0.E0,1.E0,0.E0)); -#29898=DIRECTION('',(0.E0,0.E0,-1.E0)); -#29899=AXIS2_PLACEMENT_3D('',#29896,#29897,#29898); -#29900=PLANE('',#29899); -#29902=ORIENTED_EDGE('',*,*,#29901,.F.); -#29904=ORIENTED_EDGE('',*,*,#29903,.F.); -#29906=ORIENTED_EDGE('',*,*,#29905,.F.); -#29908=ORIENTED_EDGE('',*,*,#29907,.F.); -#29910=ORIENTED_EDGE('',*,*,#29909,.F.); -#29912=ORIENTED_EDGE('',*,*,#29911,.F.); -#29914=ORIENTED_EDGE('',*,*,#29913,.F.); -#29916=ORIENTED_EDGE('',*,*,#29915,.F.); -#29918=ORIENTED_EDGE('',*,*,#29917,.F.); -#29920=ORIENTED_EDGE('',*,*,#29919,.F.); -#29922=ORIENTED_EDGE('',*,*,#29921,.F.); -#29924=ORIENTED_EDGE('',*,*,#29923,.F.); -#29926=ORIENTED_EDGE('',*,*,#29925,.F.); -#29928=ORIENTED_EDGE('',*,*,#29927,.F.); -#29930=ORIENTED_EDGE('',*,*,#29929,.F.); -#29932=ORIENTED_EDGE('',*,*,#29931,.F.); -#29934=ORIENTED_EDGE('',*,*,#29933,.F.); -#29936=ORIENTED_EDGE('',*,*,#29935,.F.); -#29938=ORIENTED_EDGE('',*,*,#29937,.F.); -#29940=ORIENTED_EDGE('',*,*,#29939,.F.); -#29942=ORIENTED_EDGE('',*,*,#29941,.F.); -#29944=ORIENTED_EDGE('',*,*,#29943,.F.); -#29946=ORIENTED_EDGE('',*,*,#29945,.F.); -#29948=ORIENTED_EDGE('',*,*,#29947,.F.); -#29950=ORIENTED_EDGE('',*,*,#29949,.F.); -#29952=ORIENTED_EDGE('',*,*,#29951,.F.); -#29954=ORIENTED_EDGE('',*,*,#29953,.F.); -#29956=ORIENTED_EDGE('',*,*,#29955,.F.); -#29958=ORIENTED_EDGE('',*,*,#29957,.F.); -#29960=ORIENTED_EDGE('',*,*,#29959,.F.); -#29962=ORIENTED_EDGE('',*,*,#29961,.F.); -#29964=ORIENTED_EDGE('',*,*,#29963,.F.); -#29966=ORIENTED_EDGE('',*,*,#29965,.F.); -#29968=ORIENTED_EDGE('',*,*,#29967,.F.); -#29970=ORIENTED_EDGE('',*,*,#29969,.F.); -#29972=ORIENTED_EDGE('',*,*,#29971,.F.); -#29974=ORIENTED_EDGE('',*,*,#29973,.F.); -#29976=ORIENTED_EDGE('',*,*,#29975,.F.); -#29978=ORIENTED_EDGE('',*,*,#29977,.F.); -#29980=ORIENTED_EDGE('',*,*,#29979,.F.); -#29982=ORIENTED_EDGE('',*,*,#29981,.F.); -#29984=ORIENTED_EDGE('',*,*,#29983,.F.); -#29986=ORIENTED_EDGE('',*,*,#29985,.F.); -#29988=ORIENTED_EDGE('',*,*,#29987,.F.); -#29990=ORIENTED_EDGE('',*,*,#29989,.F.); -#29992=ORIENTED_EDGE('',*,*,#29991,.F.); -#29994=ORIENTED_EDGE('',*,*,#29993,.F.); -#29996=ORIENTED_EDGE('',*,*,#29995,.F.); -#29998=ORIENTED_EDGE('',*,*,#29997,.F.); -#30000=ORIENTED_EDGE('',*,*,#29999,.F.); -#30002=ORIENTED_EDGE('',*,*,#30001,.F.); -#30004=ORIENTED_EDGE('',*,*,#30003,.F.); -#30006=ORIENTED_EDGE('',*,*,#30005,.F.); -#30008=ORIENTED_EDGE('',*,*,#30007,.F.); -#30010=ORIENTED_EDGE('',*,*,#30009,.F.); -#30012=ORIENTED_EDGE('',*,*,#30011,.F.); -#30014=ORIENTED_EDGE('',*,*,#30013,.F.); -#30015=EDGE_LOOP('',(#29902,#29904,#29906,#29908,#29910,#29912,#29914,#29916, -#29918,#29920,#29922,#29924,#29926,#29928,#29930,#29932,#29934,#29936,#29938, -#29940,#29942,#29944,#29946,#29948,#29950,#29952,#29954,#29956,#29958,#29960, -#29962,#29964,#29966,#29968,#29970,#29972,#29974,#29976,#29978,#29980,#29982, -#29984,#29986,#29988,#29990,#29992,#29994,#29996,#29998,#30000,#30002,#30004, -#30006,#30008,#30010,#30012,#30014)); -#30016=FACE_OUTER_BOUND('',#30015,.F.); -#30018=FILL_AREA_STYLE_COLOUR('',#17); -#30019=FILL_AREA_STYLE('',(#30018)); -#30020=SURFACE_STYLE_FILL_AREA(#30019); -#30021=SURFACE_SIDE_STYLE('',(#30020)); -#30022=SURFACE_STYLE_USAGE(.POSITIVE.,#30021); -#30023=PRESENTATION_STYLE_ASSIGNMENT((#30022)); -#30024=STYLED_ITEM('',(#30023),#30017); -#30025=CARTESIAN_POINT('',(0.E0,1.5E0,0.E0)); -#30026=DIRECTION('',(0.E0,1.E0,0.E0)); -#30027=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30028=AXIS2_PLACEMENT_3D('',#30025,#30026,#30027); -#30029=PLANE('',#30028); -#30031=ORIENTED_EDGE('',*,*,#30030,.F.); -#30033=ORIENTED_EDGE('',*,*,#30032,.F.); -#30035=ORIENTED_EDGE('',*,*,#30034,.F.); -#30037=ORIENTED_EDGE('',*,*,#30036,.F.); -#30039=ORIENTED_EDGE('',*,*,#30038,.F.); -#30041=ORIENTED_EDGE('',*,*,#30040,.F.); -#30043=ORIENTED_EDGE('',*,*,#30042,.F.); -#30045=ORIENTED_EDGE('',*,*,#30044,.F.); -#30047=ORIENTED_EDGE('',*,*,#30046,.F.); -#30049=ORIENTED_EDGE('',*,*,#30048,.F.); -#30051=ORIENTED_EDGE('',*,*,#30050,.F.); -#30053=ORIENTED_EDGE('',*,*,#30052,.F.); -#30055=ORIENTED_EDGE('',*,*,#30054,.F.); -#30057=ORIENTED_EDGE('',*,*,#30056,.F.); -#30059=ORIENTED_EDGE('',*,*,#30058,.F.); -#30061=ORIENTED_EDGE('',*,*,#30060,.F.); -#30063=ORIENTED_EDGE('',*,*,#30062,.F.); -#30065=ORIENTED_EDGE('',*,*,#30064,.F.); -#30067=ORIENTED_EDGE('',*,*,#30066,.F.); -#30069=ORIENTED_EDGE('',*,*,#30068,.F.); -#30071=ORIENTED_EDGE('',*,*,#30070,.F.); -#30073=ORIENTED_EDGE('',*,*,#30072,.F.); -#30075=ORIENTED_EDGE('',*,*,#30074,.F.); -#30077=ORIENTED_EDGE('',*,*,#30076,.F.); -#30079=ORIENTED_EDGE('',*,*,#30078,.F.); -#30081=ORIENTED_EDGE('',*,*,#30080,.F.); -#30083=ORIENTED_EDGE('',*,*,#30082,.F.); -#30085=ORIENTED_EDGE('',*,*,#30084,.F.); -#30086=EDGE_LOOP('',(#30031,#30033,#30035,#30037,#30039,#30041,#30043,#30045, -#30047,#30049,#30051,#30053,#30055,#30057,#30059,#30061,#30063,#30065,#30067, -#30069,#30071,#30073,#30075,#30077,#30079,#30081,#30083,#30085)); -#30087=FACE_OUTER_BOUND('',#30086,.F.); -#30089=FILL_AREA_STYLE_COLOUR('',#17); -#30090=FILL_AREA_STYLE('',(#30089)); -#30091=SURFACE_STYLE_FILL_AREA(#30090); -#30092=SURFACE_SIDE_STYLE('',(#30091)); -#30093=SURFACE_STYLE_USAGE(.POSITIVE.,#30092); -#30094=PRESENTATION_STYLE_ASSIGNMENT((#30093)); -#30095=STYLED_ITEM('',(#30094),#30088); -#30096=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.830979256152E0)); -#30097=DIRECTION('',(1.E0,0.E0,0.E0)); -#30098=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30099=AXIS2_PLACEMENT_3D('',#30096,#30097,#30098); -#30100=PLANE('',#30099); -#30101=ORIENTED_EDGE('',*,*,#26334,.F.); -#30103=ORIENTED_EDGE('',*,*,#30102,.T.); -#30104=ORIENTED_EDGE('',*,*,#27469,.T.); -#30106=ORIENTED_EDGE('',*,*,#30105,.F.); -#30107=EDGE_LOOP('',(#30101,#30103,#30104,#30106)); -#30108=FACE_OUTER_BOUND('',#30107,.F.); -#30110=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.830979256152E0)); -#30111=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30112=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30113=AXIS2_PLACEMENT_3D('',#30110,#30111,#30112); -#30114=PLANE('',#30113); -#30115=ORIENTED_EDGE('',*,*,#26352,.F.); -#30117=ORIENTED_EDGE('',*,*,#30116,.T.); -#30118=ORIENTED_EDGE('',*,*,#27471,.T.); -#30119=ORIENTED_EDGE('',*,*,#30102,.F.); -#30120=EDGE_LOOP('',(#30115,#30117,#30118,#30119)); -#30121=FACE_OUTER_BOUND('',#30120,.F.); -#30123=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,8.295746927498E0)); -#30124=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30125=DIRECTION('',(0.E0,0.E0,1.E0)); -#30126=AXIS2_PLACEMENT_3D('',#30123,#30124,#30125); -#30127=PLANE('',#30126); -#30128=ORIENTED_EDGE('',*,*,#26350,.F.); -#30130=ORIENTED_EDGE('',*,*,#30129,.T.); -#30131=ORIENTED_EDGE('',*,*,#27473,.T.); -#30132=ORIENTED_EDGE('',*,*,#30116,.F.); -#30133=EDGE_LOOP('',(#30128,#30130,#30131,#30132)); -#30134=FACE_OUTER_BOUND('',#30133,.F.); -#30136=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,8.211236555574E0)); -#30137=DIRECTION('',(-8.931638525254E-1,0.E0,4.497314004403E-1)); -#30138=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#30139=AXIS2_PLACEMENT_3D('',#30136,#30137,#30138); -#30140=PLANE('',#30139); -#30141=ORIENTED_EDGE('',*,*,#26348,.F.); -#30143=ORIENTED_EDGE('',*,*,#30142,.T.); -#30144=ORIENTED_EDGE('',*,*,#27475,.T.); -#30145=ORIENTED_EDGE('',*,*,#30129,.F.); -#30146=EDGE_LOOP('',(#30141,#30143,#30144,#30145)); -#30147=FACE_OUTER_BOUND('',#30146,.F.); -#30149=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,8.154896280760E0)); -#30150=DIRECTION('',(-5.520023570683E-1,0.E0,8.338425497605E-1)); -#30151=DIRECTION('',(8.338425497605E-1,0.E0,5.520023570683E-1)); -#30152=AXIS2_PLACEMENT_3D('',#30149,#30150,#30151); -#30153=PLANE('',#30152); -#30154=ORIENTED_EDGE('',*,*,#26346,.F.); -#30156=ORIENTED_EDGE('',*,*,#30155,.T.); -#30157=ORIENTED_EDGE('',*,*,#27477,.T.); -#30158=ORIENTED_EDGE('',*,*,#30142,.F.); -#30159=EDGE_LOOP('',(#30154,#30156,#30157,#30158)); -#30160=FACE_OUTER_BOUND('',#30159,.F.); -#30162=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,8.126726183650E0)); -#30163=DIRECTION('',(-2.154818712031E-1,0.E0,9.765078408199E-1)); -#30164=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#30165=AXIS2_PLACEMENT_3D('',#30162,#30163,#30164); -#30166=PLANE('',#30165); -#30167=ORIENTED_EDGE('',*,*,#26344,.F.); -#30169=ORIENTED_EDGE('',*,*,#30168,.T.); -#30170=ORIENTED_EDGE('',*,*,#27479,.T.); -#30171=ORIENTED_EDGE('',*,*,#30155,.F.); -#30172=EDGE_LOOP('',(#30167,#30169,#30170,#30171)); -#30173=FACE_OUTER_BOUND('',#30172,.F.); -#30175=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,8.126726183650E0)); -#30176=DIRECTION('',(0.E0,0.E0,1.E0)); -#30177=DIRECTION('',(1.E0,0.E0,0.E0)); -#30178=AXIS2_PLACEMENT_3D('',#30175,#30176,#30177); -#30179=PLANE('',#30178); -#30180=ORIENTED_EDGE('',*,*,#26342,.F.); -#30182=ORIENTED_EDGE('',*,*,#30181,.T.); -#30183=ORIENTED_EDGE('',*,*,#27481,.T.); -#30184=ORIENTED_EDGE('',*,*,#30168,.F.); -#30185=EDGE_LOOP('',(#30180,#30182,#30183,#30184)); -#30186=FACE_OUTER_BOUND('',#30185,.F.); -#30188=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,8.154896280760E0)); -#30189=DIRECTION('',(2.154816793280E-1,0.E0,9.765078831602E-1)); -#30190=DIRECTION('',(9.765078831602E-1,0.E0,-2.154816793280E-1)); -#30191=AXIS2_PLACEMENT_3D('',#30188,#30189,#30190); -#30192=PLANE('',#30191); -#30193=ORIENTED_EDGE('',*,*,#26340,.F.); -#30195=ORIENTED_EDGE('',*,*,#30194,.T.); -#30196=ORIENTED_EDGE('',*,*,#27483,.T.); -#30197=ORIENTED_EDGE('',*,*,#30181,.F.); -#30198=EDGE_LOOP('',(#30193,#30195,#30196,#30197)); -#30199=FACE_OUTER_BOUND('',#30198,.F.); -#30201=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,8.211236555574E0)); -#30202=DIRECTION('',(5.520023570683E-1,0.E0,8.338425497605E-1)); -#30203=DIRECTION('',(8.338425497605E-1,0.E0,-5.520023570683E-1)); -#30204=AXIS2_PLACEMENT_3D('',#30201,#30202,#30203); -#30205=PLANE('',#30204); -#30206=ORIENTED_EDGE('',*,*,#26338,.F.); -#30208=ORIENTED_EDGE('',*,*,#30207,.T.); -#30209=ORIENTED_EDGE('',*,*,#27485,.T.); -#30210=ORIENTED_EDGE('',*,*,#30194,.F.); -#30211=EDGE_LOOP('',(#30206,#30208,#30209,#30210)); -#30212=FACE_OUTER_BOUND('',#30211,.F.); -#30214=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,8.295746927498E0)); -#30215=DIRECTION('',(8.931638525254E-1,0.E0,4.497314004403E-1)); -#30216=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#30217=AXIS2_PLACEMENT_3D('',#30214,#30215,#30216); -#30218=PLANE('',#30217); -#30219=ORIENTED_EDGE('',*,*,#26336,.F.); -#30220=ORIENTED_EDGE('',*,*,#30105,.T.); -#30221=ORIENTED_EDGE('',*,*,#27487,.T.); -#30222=ORIENTED_EDGE('',*,*,#30207,.F.); -#30223=EDGE_LOOP('',(#30219,#30220,#30221,#30222)); -#30224=FACE_OUTER_BOUND('',#30223,.F.); -#30226=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,8.126726183650E0)); -#30227=DIRECTION('',(0.E0,0.E0,1.E0)); -#30228=DIRECTION('',(1.E0,0.E0,0.E0)); -#30229=AXIS2_PLACEMENT_3D('',#30226,#30227,#30228); -#30230=PLANE('',#30229); -#30231=ORIENTED_EDGE('',*,*,#26362,.F.); -#30233=ORIENTED_EDGE('',*,*,#30232,.T.); -#30234=ORIENTED_EDGE('',*,*,#27491,.T.); -#30236=ORIENTED_EDGE('',*,*,#30235,.F.); -#30237=EDGE_LOOP('',(#30231,#30233,#30234,#30236)); -#30238=FACE_OUTER_BOUND('',#30237,.F.); -#30240=CARTESIAN_POINT('',(1.234042525291E0,1.55E0,8.154896280760E0)); -#30241=DIRECTION('',(2.154817752655E-1,0.E0,9.765078619901E-1)); -#30242=DIRECTION('',(9.765078619901E-1,0.E0,-2.154817752655E-1)); -#30243=AXIS2_PLACEMENT_3D('',#30240,#30241,#30242); -#30244=PLANE('',#30243); -#30245=ORIENTED_EDGE('',*,*,#26380,.F.); -#30247=ORIENTED_EDGE('',*,*,#30246,.T.); -#30248=ORIENTED_EDGE('',*,*,#27493,.T.); -#30249=ORIENTED_EDGE('',*,*,#30232,.F.); -#30250=EDGE_LOOP('',(#30245,#30247,#30248,#30249)); -#30251=FACE_OUTER_BOUND('',#30250,.F.); -#30253=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,8.211236555574E0)); -#30254=DIRECTION('',(5.520023570683E-1,0.E0,8.338425497605E-1)); -#30255=DIRECTION('',(8.338425497605E-1,0.E0,-5.520023570683E-1)); -#30256=AXIS2_PLACEMENT_3D('',#30253,#30254,#30255); -#30257=PLANE('',#30256); -#30258=ORIENTED_EDGE('',*,*,#26378,.F.); -#30260=ORIENTED_EDGE('',*,*,#30259,.T.); -#30261=ORIENTED_EDGE('',*,*,#27495,.T.); -#30262=ORIENTED_EDGE('',*,*,#30246,.F.); -#30263=EDGE_LOOP('',(#30258,#30260,#30261,#30262)); -#30264=FACE_OUTER_BOUND('',#30263,.F.); -#30266=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.295746927498E0)); -#30267=DIRECTION('',(8.931638525254E-1,0.E0,4.497314004403E-1)); -#30268=DIRECTION('',(4.497314004403E-1,0.E0,-8.931638525254E-1)); -#30269=AXIS2_PLACEMENT_3D('',#30266,#30267,#30268); -#30270=PLANE('',#30269); -#30271=ORIENTED_EDGE('',*,*,#26376,.F.); -#30273=ORIENTED_EDGE('',*,*,#30272,.T.); -#30274=ORIENTED_EDGE('',*,*,#27497,.T.); -#30275=ORIENTED_EDGE('',*,*,#30259,.F.); -#30276=EDGE_LOOP('',(#30271,#30273,#30274,#30275)); -#30277=FACE_OUTER_BOUND('',#30276,.F.); -#30279=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,8.830979256152E0)); -#30280=DIRECTION('',(1.E0,0.E0,0.E0)); -#30281=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30282=AXIS2_PLACEMENT_3D('',#30279,#30280,#30281); -#30283=PLANE('',#30282); -#30284=ORIENTED_EDGE('',*,*,#26374,.F.); -#30286=ORIENTED_EDGE('',*,*,#30285,.T.); -#30287=ORIENTED_EDGE('',*,*,#27499,.T.); -#30288=ORIENTED_EDGE('',*,*,#30272,.F.); -#30289=EDGE_LOOP('',(#30284,#30286,#30287,#30288)); -#30290=FACE_OUTER_BOUND('',#30289,.F.); -#30292=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.830979256152E0)); -#30293=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30294=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30295=AXIS2_PLACEMENT_3D('',#30292,#30293,#30294); -#30296=PLANE('',#30295); -#30297=ORIENTED_EDGE('',*,*,#26372,.F.); -#30299=ORIENTED_EDGE('',*,*,#30298,.T.); -#30300=ORIENTED_EDGE('',*,*,#27501,.T.); -#30301=ORIENTED_EDGE('',*,*,#30285,.F.); -#30302=EDGE_LOOP('',(#30297,#30299,#30300,#30301)); -#30303=FACE_OUTER_BOUND('',#30302,.F.); -#30305=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,8.295746927498E0)); -#30306=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30307=DIRECTION('',(0.E0,0.E0,1.E0)); -#30308=AXIS2_PLACEMENT_3D('',#30305,#30306,#30307); -#30309=PLANE('',#30308); -#30310=ORIENTED_EDGE('',*,*,#26370,.F.); -#30312=ORIENTED_EDGE('',*,*,#30311,.T.); -#30313=ORIENTED_EDGE('',*,*,#27503,.T.); -#30314=ORIENTED_EDGE('',*,*,#30298,.F.); -#30315=EDGE_LOOP('',(#30310,#30312,#30313,#30314)); -#30316=FACE_OUTER_BOUND('',#30315,.F.); -#30318=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,8.211236555574E0)); -#30319=DIRECTION('',(-8.931638525254E-1,0.E0,4.497314004403E-1)); -#30320=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#30321=AXIS2_PLACEMENT_3D('',#30318,#30319,#30320); -#30322=PLANE('',#30321); -#30323=ORIENTED_EDGE('',*,*,#26368,.F.); -#30325=ORIENTED_EDGE('',*,*,#30324,.T.); -#30326=ORIENTED_EDGE('',*,*,#27505,.T.); -#30327=ORIENTED_EDGE('',*,*,#30311,.F.); -#30328=EDGE_LOOP('',(#30323,#30325,#30326,#30327)); -#30329=FACE_OUTER_BOUND('',#30328,.F.); -#30331=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,8.154896280760E0)); -#30332=DIRECTION('',(-5.520022226690E-1,0.E0,8.338426387325E-1)); -#30333=DIRECTION('',(8.338426387325E-1,0.E0,5.520022226690E-1)); -#30334=AXIS2_PLACEMENT_3D('',#30331,#30332,#30333); -#30335=PLANE('',#30334); -#30336=ORIENTED_EDGE('',*,*,#26366,.F.); -#30338=ORIENTED_EDGE('',*,*,#30337,.T.); -#30339=ORIENTED_EDGE('',*,*,#27507,.T.); -#30340=ORIENTED_EDGE('',*,*,#30324,.F.); -#30341=EDGE_LOOP('',(#30336,#30338,#30339,#30340)); -#30342=FACE_OUTER_BOUND('',#30341,.F.); -#30344=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,8.126726183650E0)); -#30345=DIRECTION('',(-2.154818712031E-1,0.E0,9.765078408199E-1)); -#30346=DIRECTION('',(9.765078408199E-1,0.E0,2.154818712031E-1)); -#30347=AXIS2_PLACEMENT_3D('',#30344,#30345,#30346); -#30348=PLANE('',#30347); -#30349=ORIENTED_EDGE('',*,*,#26364,.F.); -#30350=ORIENTED_EDGE('',*,*,#30235,.T.); -#30351=ORIENTED_EDGE('',*,*,#27509,.T.); -#30352=ORIENTED_EDGE('',*,*,#30337,.F.); -#30353=EDGE_LOOP('',(#30349,#30350,#30351,#30352)); -#30354=FACE_OUTER_BOUND('',#30353,.F.); -#30356=CARTESIAN_POINT('',(0.E0,1.55E0,6.661879763833E0)); -#30357=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30358=DIRECTION('',(0.E0,0.E0,1.E0)); -#30359=AXIS2_PLACEMENT_3D('',#30356,#30357,#30358); -#30360=PLANE('',#30359); -#30361=ORIENTED_EDGE('',*,*,#24620,.F.); -#30363=ORIENTED_EDGE('',*,*,#30362,.T.); -#30364=ORIENTED_EDGE('',*,*,#27526,.T.); -#30366=ORIENTED_EDGE('',*,*,#30365,.F.); -#30367=EDGE_LOOP('',(#30361,#30363,#30364,#30366)); -#30368=FACE_OUTER_BOUND('',#30367,.F.); -#30370=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,6.661879763833E0)); -#30371=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30372=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30373=AXIS2_PLACEMENT_3D('',#30370,#30371,#30372); -#30374=PLANE('',#30373); -#30375=ORIENTED_EDGE('',*,*,#24634,.F.); -#30377=ORIENTED_EDGE('',*,*,#30376,.T.); -#30378=ORIENTED_EDGE('',*,*,#27528,.T.); -#30379=ORIENTED_EDGE('',*,*,#30362,.F.); -#30380=EDGE_LOOP('',(#30375,#30377,#30378,#30379)); -#30381=FACE_OUTER_BOUND('',#30380,.F.); -#30383=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.112601639967E0)); -#30384=DIRECTION('',(1.E0,0.E0,0.E0)); -#30385=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30386=AXIS2_PLACEMENT_3D('',#30383,#30384,#30385); -#30387=PLANE('',#30386); -#30388=ORIENTED_EDGE('',*,*,#24632,.F.); -#30390=ORIENTED_EDGE('',*,*,#30389,.T.); -#30391=ORIENTED_EDGE('',*,*,#27530,.T.); -#30392=ORIENTED_EDGE('',*,*,#30376,.F.); -#30393=EDGE_LOOP('',(#30388,#30390,#30391,#30392)); -#30394=FACE_OUTER_BOUND('',#30393,.F.); -#30396=CARTESIAN_POINT('',(2.E0,1.55E0,7.112601639967E0)); -#30397=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30398=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30399=AXIS2_PLACEMENT_3D('',#30396,#30397,#30398); -#30400=PLANE('',#30399); -#30401=ORIENTED_EDGE('',*,*,#24630,.F.); -#30403=ORIENTED_EDGE('',*,*,#30402,.T.); -#30404=ORIENTED_EDGE('',*,*,#27532,.T.); -#30405=ORIENTED_EDGE('',*,*,#30389,.F.); -#30406=EDGE_LOOP('',(#30401,#30403,#30404,#30405)); -#30407=FACE_OUTER_BOUND('',#30406,.F.); -#30409=CARTESIAN_POINT('',(2.E0,1.55E0,7.281622383815E0)); -#30410=DIRECTION('',(1.E0,0.E0,0.E0)); -#30411=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30412=AXIS2_PLACEMENT_3D('',#30409,#30410,#30411); -#30413=PLANE('',#30412); -#30414=ORIENTED_EDGE('',*,*,#24628,.F.); -#30416=ORIENTED_EDGE('',*,*,#30415,.T.); -#30417=ORIENTED_EDGE('',*,*,#27534,.T.); -#30418=ORIENTED_EDGE('',*,*,#30402,.F.); -#30419=EDGE_LOOP('',(#30414,#30416,#30417,#30418)); -#30420=FACE_OUTER_BOUND('',#30419,.F.); -#30422=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.281622383815E0)); -#30423=DIRECTION('',(0.E0,0.E0,1.E0)); -#30424=DIRECTION('',(1.E0,0.E0,0.E0)); -#30425=AXIS2_PLACEMENT_3D('',#30422,#30423,#30424); -#30426=PLANE('',#30425); -#30427=ORIENTED_EDGE('',*,*,#24626,.F.); -#30429=ORIENTED_EDGE('',*,*,#30428,.T.); -#30430=ORIENTED_EDGE('',*,*,#27536,.T.); -#30431=ORIENTED_EDGE('',*,*,#30415,.F.); -#30432=EDGE_LOOP('',(#30427,#30429,#30430,#30431)); -#30433=FACE_OUTER_BOUND('',#30432,.F.); -#30435=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,7.732344421140E0)); -#30436=DIRECTION('',(1.E0,0.E0,0.E0)); -#30437=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30438=AXIS2_PLACEMENT_3D('',#30435,#30436,#30437); -#30439=PLANE('',#30438); -#30440=ORIENTED_EDGE('',*,*,#24624,.F.); -#30442=ORIENTED_EDGE('',*,*,#30441,.T.); -#30443=ORIENTED_EDGE('',*,*,#27538,.T.); -#30444=ORIENTED_EDGE('',*,*,#30428,.F.); -#30445=EDGE_LOOP('',(#30440,#30442,#30443,#30444)); -#30446=FACE_OUTER_BOUND('',#30445,.F.); -#30448=CARTESIAN_POINT('',(0.E0,1.55E0,7.732344421140E0)); -#30449=DIRECTION('',(0.E0,0.E0,1.E0)); -#30450=DIRECTION('',(1.E0,0.E0,0.E0)); -#30451=AXIS2_PLACEMENT_3D('',#30448,#30449,#30450); -#30452=PLANE('',#30451); -#30453=ORIENTED_EDGE('',*,*,#24622,.F.); -#30454=ORIENTED_EDGE('',*,*,#30365,.T.); -#30455=ORIENTED_EDGE('',*,*,#27540,.T.); -#30456=ORIENTED_EDGE('',*,*,#30441,.F.); -#30457=EDGE_LOOP('',(#30453,#30454,#30455,#30456)); -#30458=FACE_OUTER_BOUND('',#30457,.F.); -#30460=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,6.211157726508E0)); -#30461=DIRECTION('',(-7.979700564663E-1,0.E0,6.026970955489E-1)); -#30462=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#30463=AXIS2_PLACEMENT_3D('',#30460,#30461,#30462); -#30464=PLANE('',#30463); -#30465=ORIENTED_EDGE('',*,*,#24638,.F.); -#30467=ORIENTED_EDGE('',*,*,#30466,.T.); -#30468=ORIENTED_EDGE('',*,*,#27557,.T.); -#30470=ORIENTED_EDGE('',*,*,#30469,.F.); -#30471=EDGE_LOOP('',(#30465,#30467,#30468,#30470)); -#30472=FACE_OUTER_BOUND('',#30471,.F.); -#30474=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,6.267498081918E0)); -#30475=DIRECTION('',(7.979700564663E-1,0.E0,6.026970955489E-1)); -#30476=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#30477=AXIS2_PLACEMENT_3D('',#30474,#30475,#30476); -#30478=PLANE('',#30477); -#30479=ORIENTED_EDGE('',*,*,#24704,.F.); -#30481=ORIENTED_EDGE('',*,*,#30480,.T.); -#30482=ORIENTED_EDGE('',*,*,#27559,.T.); -#30483=ORIENTED_EDGE('',*,*,#30466,.F.); -#30484=EDGE_LOOP('',(#30479,#30481,#30482,#30483)); -#30485=FACE_OUTER_BOUND('',#30484,.F.); -#30487=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,6.352008292651E0)); -#30488=DIRECTION('',(5.520014420087E-1,0.E0,8.338431555277E-1)); -#30489=DIRECTION('',(8.338431555277E-1,0.E0,-5.520014420087E-1)); -#30490=AXIS2_PLACEMENT_3D('',#30487,#30488,#30489); -#30491=PLANE('',#30490); -#30492=ORIENTED_EDGE('',*,*,#24702,.F.); -#30494=ORIENTED_EDGE('',*,*,#30493,.T.); -#30495=ORIENTED_EDGE('',*,*,#27561,.T.); -#30496=ORIENTED_EDGE('',*,*,#30480,.F.); -#30497=EDGE_LOOP('',(#30492,#30494,#30495,#30496)); -#30498=FACE_OUTER_BOUND('',#30497,.F.); -#30500=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,6.408348648061E0)); -#30501=DIRECTION('',(3.142331229740E-1,0.E0,9.493458507973E-1)); -#30502=DIRECTION('',(9.493458507973E-1,0.E0,-3.142331229740E-1)); -#30503=AXIS2_PLACEMENT_3D('',#30500,#30501,#30502); -#30504=PLANE('',#30503); -#30505=ORIENTED_EDGE('',*,*,#24700,.F.); -#30507=ORIENTED_EDGE('',*,*,#30506,.T.); -#30508=ORIENTED_EDGE('',*,*,#27563,.T.); -#30509=ORIENTED_EDGE('',*,*,#30493,.F.); -#30510=EDGE_LOOP('',(#30505,#30507,#30508,#30509)); -#30511=FACE_OUTER_BOUND('',#30510,.F.); -#30513=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.408348648061E0)); -#30514=DIRECTION('',(0.E0,0.E0,1.E0)); -#30515=DIRECTION('',(1.E0,0.E0,0.E0)); -#30516=AXIS2_PLACEMENT_3D('',#30513,#30514,#30515); -#30517=PLANE('',#30516); -#30518=ORIENTED_EDGE('',*,*,#24698,.F.); -#30520=ORIENTED_EDGE('',*,*,#30519,.T.); -#30521=ORIENTED_EDGE('',*,*,#27565,.T.); -#30522=ORIENTED_EDGE('',*,*,#30506,.F.); -#30523=EDGE_LOOP('',(#30518,#30520,#30521,#30522)); -#30524=FACE_OUTER_BOUND('',#30523,.F.); -#30526=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,6.352008292651E0)); -#30527=DIRECTION('',(-2.559771804186E-1,0.E0,9.666828244595E-1)); -#30528=DIRECTION('',(9.666828244595E-1,0.E0,2.559771804186E-1)); -#30529=AXIS2_PLACEMENT_3D('',#30526,#30527,#30528); -#30530=PLANE('',#30529); -#30531=ORIENTED_EDGE('',*,*,#24696,.F.); -#30533=ORIENTED_EDGE('',*,*,#30532,.T.); -#30534=ORIENTED_EDGE('',*,*,#27567,.T.); -#30535=ORIENTED_EDGE('',*,*,#30519,.F.); -#30536=EDGE_LOOP('',(#30531,#30533,#30534,#30535)); -#30537=FACE_OUTER_BOUND('',#30536,.F.); -#30539=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,6.267498081918E0)); -#30540=DIRECTION('',(-5.520014420087E-1,0.E0,8.338431555277E-1)); -#30541=DIRECTION('',(8.338431555277E-1,0.E0,5.520014420087E-1)); -#30542=AXIS2_PLACEMENT_3D('',#30539,#30540,#30541); -#30543=PLANE('',#30542); -#30544=ORIENTED_EDGE('',*,*,#24694,.F.); -#30546=ORIENTED_EDGE('',*,*,#30545,.T.); -#30547=ORIENTED_EDGE('',*,*,#27569,.T.); -#30548=ORIENTED_EDGE('',*,*,#30532,.F.); -#30549=EDGE_LOOP('',(#30544,#30546,#30547,#30548)); -#30550=FACE_OUTER_BOUND('',#30549,.F.); -#30552=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,6.126647354584E0)); -#30553=DIRECTION('',(-7.409513837740E-1,0.E0,6.715586697255E-1)); -#30554=DIRECTION('',(6.715586697255E-1,0.E0,7.409513837740E-1)); -#30555=AXIS2_PLACEMENT_3D('',#30552,#30553,#30554); -#30556=PLANE('',#30555); -#30557=ORIENTED_EDGE('',*,*,#24692,.F.); -#30559=ORIENTED_EDGE('',*,*,#30558,.T.); -#30560=ORIENTED_EDGE('',*,*,#27571,.T.); -#30561=ORIENTED_EDGE('',*,*,#30545,.F.); -#30562=EDGE_LOOP('',(#30557,#30559,#30560,#30561)); -#30563=FACE_OUTER_BOUND('',#30562,.F.); -#30565=CARTESIAN_POINT('',(0.E0,1.55E0,5.985796627250E0)); -#30566=DIRECTION('',(-9.572671195869E-1,0.E0,2.892052242921E-1)); -#30567=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#30568=AXIS2_PLACEMENT_3D('',#30565,#30566,#30567); -#30569=PLANE('',#30568); -#30570=ORIENTED_EDGE('',*,*,#24690,.F.); -#30572=ORIENTED_EDGE('',*,*,#30571,.T.); -#30573=ORIENTED_EDGE('',*,*,#27573,.T.); -#30574=ORIENTED_EDGE('',*,*,#30558,.F.); -#30575=EDGE_LOOP('',(#30570,#30572,#30573,#30574)); -#30576=FACE_OUTER_BOUND('',#30575,.F.); -#30578=CARTESIAN_POINT('',(0.E0,1.55E0,5.873116238812E0)); -#30579=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30580=DIRECTION('',(0.E0,0.E0,1.E0)); -#30581=AXIS2_PLACEMENT_3D('',#30578,#30579,#30580); -#30582=PLANE('',#30581); -#30583=ORIENTED_EDGE('',*,*,#24688,.F.); -#30585=ORIENTED_EDGE('',*,*,#30584,.T.); -#30586=ORIENTED_EDGE('',*,*,#27575,.T.); -#30587=ORIENTED_EDGE('',*,*,#30571,.F.); -#30588=EDGE_LOOP('',(#30583,#30585,#30586,#30587)); -#30589=FACE_OUTER_BOUND('',#30588,.F.); -#30591=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,5.732265511478E0)); -#30592=DIRECTION('',(-9.572671195869E-1,0.E0,-2.892052242921E-1)); -#30593=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#30594=AXIS2_PLACEMENT_3D('',#30591,#30592,#30593); -#30595=PLANE('',#30594); -#30596=ORIENTED_EDGE('',*,*,#24686,.F.); -#30598=ORIENTED_EDGE('',*,*,#30597,.T.); -#30599=ORIENTED_EDGE('',*,*,#27577,.T.); -#30600=ORIENTED_EDGE('',*,*,#30584,.F.); -#30601=EDGE_LOOP('',(#30596,#30598,#30599,#30600)); -#30602=FACE_OUTER_BOUND('',#30601,.F.); -#30604=CARTESIAN_POINT('',(1.702127456665E-1,1.55E0,5.591415106526E0)); -#30605=DIRECTION('',(-7.409506189360E-1,0.E0,-6.715595135938E-1)); -#30606=DIRECTION('',(-6.715595135938E-1,0.E0,7.409506189360E-1)); -#30607=AXIS2_PLACEMENT_3D('',#30604,#30605,#30606); -#30608=PLANE('',#30607); -#30609=ORIENTED_EDGE('',*,*,#24684,.F.); -#30611=ORIENTED_EDGE('',*,*,#30610,.T.); -#30612=ORIENTED_EDGE('',*,*,#27579,.T.); -#30613=ORIENTED_EDGE('',*,*,#30597,.F.); -#30614=EDGE_LOOP('',(#30609,#30611,#30612,#30613)); -#30615=FACE_OUTER_BOUND('',#30614,.F.); -#30617=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.506904734602E0)); -#30618=DIRECTION('',(-5.520021740566E-1,0.E0,-8.338426709139E-1)); -#30619=DIRECTION('',(-8.338426709139E-1,0.E0,5.520021740566E-1)); -#30620=AXIS2_PLACEMENT_3D('',#30617,#30618,#30619); -#30621=PLANE('',#30620); -#30622=ORIENTED_EDGE('',*,*,#24682,.F.); -#30624=ORIENTED_EDGE('',*,*,#30623,.T.); -#30625=ORIENTED_EDGE('',*,*,#27581,.T.); -#30626=ORIENTED_EDGE('',*,*,#30610,.F.); -#30627=EDGE_LOOP('',(#30622,#30624,#30625,#30626)); -#30628=FACE_OUTER_BOUND('',#30627,.F.); -#30630=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.450564379192E0)); -#30631=DIRECTION('',(-2.559771804186E-1,0.E0,-9.666828244595E-1)); -#30632=DIRECTION('',(-9.666828244595E-1,0.E0,2.559771804186E-1)); -#30633=AXIS2_PLACEMENT_3D('',#30630,#30631,#30632); -#30634=PLANE('',#30633); -#30635=ORIENTED_EDGE('',*,*,#24680,.F.); -#30637=ORIENTED_EDGE('',*,*,#30636,.T.); -#30638=ORIENTED_EDGE('',*,*,#27583,.T.); -#30639=ORIENTED_EDGE('',*,*,#30623,.F.); -#30640=EDGE_LOOP('',(#30635,#30637,#30638,#30639)); -#30641=FACE_OUTER_BOUND('',#30640,.F.); -#30643=CARTESIAN_POINT('',(6.382979154587E-1,1.55E0,5.450564379192E0)); -#30644=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30645=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30646=AXIS2_PLACEMENT_3D('',#30643,#30644,#30645); -#30647=PLANE('',#30646); -#30648=ORIENTED_EDGE('',*,*,#24678,.F.); -#30650=ORIENTED_EDGE('',*,*,#30649,.T.); -#30651=ORIENTED_EDGE('',*,*,#27585,.T.); -#30652=ORIENTED_EDGE('',*,*,#30636,.F.); -#30653=EDGE_LOOP('',(#30648,#30650,#30651,#30652)); -#30654=FACE_OUTER_BOUND('',#30653,.F.); -#30656=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,5.506904734602E0)); -#30657=DIRECTION('',(3.142331229740E-1,0.E0,-9.493458507973E-1)); -#30658=DIRECTION('',(-9.493458507973E-1,0.E0,-3.142331229740E-1)); -#30659=AXIS2_PLACEMENT_3D('',#30656,#30657,#30658); -#30660=PLANE('',#30659); -#30661=ORIENTED_EDGE('',*,*,#24676,.F.); -#30663=ORIENTED_EDGE('',*,*,#30662,.T.); -#30664=ORIENTED_EDGE('',*,*,#27587,.T.); -#30665=ORIENTED_EDGE('',*,*,#30649,.F.); -#30666=EDGE_LOOP('',(#30661,#30663,#30664,#30665)); -#30667=FACE_OUTER_BOUND('',#30666,.F.); -#30669=CARTESIAN_POINT('',(9.361702203751E-1,1.55E0,5.591415106526E0)); -#30670=DIRECTION('',(5.520021740566E-1,0.E0,-8.338426709139E-1)); -#30671=DIRECTION('',(-8.338426709139E-1,0.E0,-5.520021740566E-1)); -#30672=AXIS2_PLACEMENT_3D('',#30669,#30670,#30671); -#30673=PLANE('',#30672); -#30674=ORIENTED_EDGE('',*,*,#24674,.F.); -#30676=ORIENTED_EDGE('',*,*,#30675,.T.); -#30677=ORIENTED_EDGE('',*,*,#27589,.T.); -#30678=ORIENTED_EDGE('',*,*,#30662,.F.); -#30679=EDGE_LOOP('',(#30674,#30676,#30677,#30678)); -#30680=FACE_OUTER_BOUND('',#30679,.F.); -#30682=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,5.647755139554E0)); -#30683=DIRECTION('',(7.979683978816E-1,0.E0,-6.026992915064E-1)); -#30684=DIRECTION('',(-6.026992915064E-1,0.E0,-7.979683978816E-1)); -#30685=AXIS2_PLACEMENT_3D('',#30682,#30683,#30684); -#30686=PLANE('',#30685); -#30687=ORIENTED_EDGE('',*,*,#24672,.F.); -#30689=ORIENTED_EDGE('',*,*,#30688,.T.); -#30690=ORIENTED_EDGE('',*,*,#27591,.T.); -#30691=ORIENTED_EDGE('',*,*,#30675,.F.); -#30692=EDGE_LOOP('',(#30687,#30689,#30690,#30691)); -#30693=FACE_OUTER_BOUND('',#30692,.F.); -#30695=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,5.591415106526E0)); -#30696=DIRECTION('',(-7.979683978816E-1,0.E0,-6.026992915064E-1)); -#30697=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#30698=AXIS2_PLACEMENT_3D('',#30695,#30696,#30697); -#30699=PLANE('',#30698); -#30700=ORIENTED_EDGE('',*,*,#24670,.F.); -#30702=ORIENTED_EDGE('',*,*,#30701,.T.); -#30703=ORIENTED_EDGE('',*,*,#27593,.T.); -#30704=ORIENTED_EDGE('',*,*,#30688,.F.); -#30705=EDGE_LOOP('',(#30700,#30702,#30703,#30704)); -#30706=FACE_OUTER_BOUND('',#30705,.F.); -#30708=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,5.478734395706E0)); -#30709=DIRECTION('',(-6.617534547244E-1,0.E0,-7.497215250747E-1)); -#30710=DIRECTION('',(-7.497215250747E-1,0.E0,6.617534547244E-1)); -#30711=AXIS2_PLACEMENT_3D('',#30708,#30709,#30710); -#30712=PLANE('',#30711); -#30713=ORIENTED_EDGE('',*,*,#24668,.F.); -#30715=ORIENTED_EDGE('',*,*,#30714,.T.); -#30716=ORIENTED_EDGE('',*,*,#27595,.T.); -#30717=ORIENTED_EDGE('',*,*,#30701,.F.); -#30718=EDGE_LOOP('',(#30713,#30715,#30716,#30717)); -#30719=FACE_OUTER_BOUND('',#30718,.F.); -#30721=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.422394362678E0)); -#30722=DIRECTION('',(-2.559758786924E-1,0.E0,-9.666831691551E-1)); -#30723=DIRECTION('',(-9.666831691551E-1,0.E0,2.559758786924E-1)); -#30724=AXIS2_PLACEMENT_3D('',#30721,#30722,#30723); -#30725=PLANE('',#30724); -#30726=ORIENTED_EDGE('',*,*,#24666,.F.); -#30728=ORIENTED_EDGE('',*,*,#30727,.T.); -#30729=ORIENTED_EDGE('',*,*,#27597,.T.); -#30730=ORIENTED_EDGE('',*,*,#30714,.F.); -#30731=EDGE_LOOP('',(#30726,#30728,#30729,#30730)); -#30732=FACE_OUTER_BOUND('',#30731,.F.); -#30734=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.422394362678E0)); -#30735=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30736=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30737=AXIS2_PLACEMENT_3D('',#30734,#30735,#30736); -#30738=PLANE('',#30737); -#30739=ORIENTED_EDGE('',*,*,#24664,.F.); -#30741=ORIENTED_EDGE('',*,*,#30740,.T.); -#30742=ORIENTED_EDGE('',*,*,#27599,.T.); -#30743=ORIENTED_EDGE('',*,*,#30727,.F.); -#30744=EDGE_LOOP('',(#30739,#30741,#30742,#30743)); -#30745=FACE_OUTER_BOUND('',#30744,.F.); -#30747=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,5.478734395706E0)); -#30748=DIRECTION('',(2.559759121978E-1,0.E0,-9.666831602829E-1)); -#30749=DIRECTION('',(-9.666831602829E-1,0.E0,-2.559759121978E-1)); -#30750=AXIS2_PLACEMENT_3D('',#30747,#30748,#30749); -#30751=PLANE('',#30750); -#30752=ORIENTED_EDGE('',*,*,#24662,.F.); -#30754=ORIENTED_EDGE('',*,*,#30753,.T.); -#30755=ORIENTED_EDGE('',*,*,#27601,.T.); -#30756=ORIENTED_EDGE('',*,*,#30740,.F.); -#30757=EDGE_LOOP('',(#30752,#30754,#30755,#30756)); -#30758=FACE_OUTER_BOUND('',#30757,.F.); -#30760=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,5.563244767630E0)); -#30761=DIRECTION('',(5.520021292568E-1,0.E0,-8.338427005713E-1)); -#30762=DIRECTION('',(-8.338427005713E-1,0.E0,-5.520021292568E-1)); -#30763=AXIS2_PLACEMENT_3D('',#30760,#30761,#30762); -#30764=PLANE('',#30763); -#30765=ORIENTED_EDGE('',*,*,#24660,.F.); -#30767=ORIENTED_EDGE('',*,*,#30766,.T.); -#30768=ORIENTED_EDGE('',*,*,#27603,.T.); -#30769=ORIENTED_EDGE('',*,*,#30753,.F.); -#30770=EDGE_LOOP('',(#30765,#30767,#30768,#30769)); -#30771=FACE_OUTER_BOUND('',#30770,.F.); -#30773=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,5.704095494964E0)); -#30774=DIRECTION('',(7.409513545199E-1,0.E0,-6.715587020024E-1)); -#30775=DIRECTION('',(-6.715587020024E-1,0.E0,-7.409513545199E-1)); -#30776=AXIS2_PLACEMENT_3D('',#30773,#30774,#30775); -#30777=PLANE('',#30776); -#30778=ORIENTED_EDGE('',*,*,#24658,.F.); -#30780=ORIENTED_EDGE('',*,*,#30779,.T.); -#30781=ORIENTED_EDGE('',*,*,#27605,.T.); -#30782=ORIENTED_EDGE('',*,*,#30766,.F.); -#30783=EDGE_LOOP('',(#30778,#30780,#30781,#30782)); -#30784=FACE_OUTER_BOUND('',#30783,.F.); -#30786=CARTESIAN_POINT('',(2.E0,1.55E0,5.844946222298E0)); -#30787=DIRECTION('',(9.572671125776E-1,0.E0,-2.892052474928E-1)); -#30788=DIRECTION('',(-2.892052474928E-1,0.E0,-9.572671125776E-1)); -#30789=AXIS2_PLACEMENT_3D('',#30786,#30787,#30788); -#30790=PLANE('',#30789); -#30791=ORIENTED_EDGE('',*,*,#24656,.F.); -#30793=ORIENTED_EDGE('',*,*,#30792,.T.); -#30794=ORIENTED_EDGE('',*,*,#27607,.T.); -#30795=ORIENTED_EDGE('',*,*,#30779,.F.); -#30796=EDGE_LOOP('',(#30791,#30793,#30794,#30795)); -#30797=FACE_OUTER_BOUND('',#30796,.F.); -#30799=CARTESIAN_POINT('',(2.E0,1.55E0,6.013966966146E0)); -#30800=DIRECTION('',(1.E0,0.E0,0.E0)); -#30801=DIRECTION('',(0.E0,0.E0,-1.E0)); -#30802=AXIS2_PLACEMENT_3D('',#30799,#30800,#30801); -#30803=PLANE('',#30802); -#30804=ORIENTED_EDGE('',*,*,#24654,.F.); -#30806=ORIENTED_EDGE('',*,*,#30805,.T.); -#30807=ORIENTED_EDGE('',*,*,#27609,.T.); -#30808=ORIENTED_EDGE('',*,*,#30792,.F.); -#30809=EDGE_LOOP('',(#30804,#30806,#30807,#30808)); -#30810=FACE_OUTER_BOUND('',#30809,.F.); -#30812=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,6.154817371098E0)); -#30813=DIRECTION('',(9.572669293217E-1,0.E0,2.892058540675E-1)); -#30814=DIRECTION('',(2.892058540675E-1,0.E0,-9.572669293217E-1)); -#30815=AXIS2_PLACEMENT_3D('',#30812,#30813,#30814); -#30816=PLANE('',#30815); -#30817=ORIENTED_EDGE('',*,*,#24652,.F.); -#30819=ORIENTED_EDGE('',*,*,#30818,.T.); -#30820=ORIENTED_EDGE('',*,*,#27611,.T.); -#30821=ORIENTED_EDGE('',*,*,#30805,.F.); -#30822=EDGE_LOOP('',(#30817,#30819,#30820,#30821)); -#30823=FACE_OUTER_BOUND('',#30822,.F.); -#30825=CARTESIAN_POINT('',(1.829787239432E0,1.55E0,6.295668098432E0)); -#30826=DIRECTION('',(7.409513545199E-1,0.E0,6.715587020024E-1)); -#30827=DIRECTION('',(6.715587020024E-1,0.E0,-7.409513545199E-1)); -#30828=AXIS2_PLACEMENT_3D('',#30825,#30826,#30827); -#30829=PLANE('',#30828); -#30830=ORIENTED_EDGE('',*,*,#24650,.F.); -#30832=ORIENTED_EDGE('',*,*,#30831,.T.); -#30833=ORIENTED_EDGE('',*,*,#27613,.T.); -#30834=ORIENTED_EDGE('',*,*,#30818,.F.); -#30835=EDGE_LOOP('',(#30830,#30832,#30833,#30834)); -#30836=FACE_OUTER_BOUND('',#30835,.F.); -#30838=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,6.380178470356E0)); -#30839=DIRECTION('',(5.520021292568E-1,0.E0,8.338427005713E-1)); -#30840=DIRECTION('',(8.338427005713E-1,0.E0,-5.520021292568E-1)); -#30841=AXIS2_PLACEMENT_3D('',#30838,#30839,#30840); -#30842=PLANE('',#30841); -#30843=ORIENTED_EDGE('',*,*,#24648,.F.); -#30845=ORIENTED_EDGE('',*,*,#30844,.T.); -#30846=ORIENTED_EDGE('',*,*,#27615,.T.); -#30847=ORIENTED_EDGE('',*,*,#30831,.F.); -#30848=EDGE_LOOP('',(#30843,#30845,#30846,#30847)); -#30849=FACE_OUTER_BOUND('',#30848,.F.); -#30851=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.436518664575E0)); -#30852=DIRECTION('',(2.559765965668E-1,0.E0,9.666829790630E-1)); -#30853=DIRECTION('',(9.666829790630E-1,0.E0,-2.559765965668E-1)); -#30854=AXIS2_PLACEMENT_3D('',#30851,#30852,#30853); -#30855=PLANE('',#30854); -#30856=ORIENTED_EDGE('',*,*,#24646,.F.); -#30858=ORIENTED_EDGE('',*,*,#30857,.T.); -#30859=ORIENTED_EDGE('',*,*,#27617,.T.); -#30860=ORIENTED_EDGE('',*,*,#30844,.F.); -#30861=EDGE_LOOP('',(#30856,#30858,#30859,#30860)); -#30862=FACE_OUTER_BOUND('',#30861,.F.); -#30864=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.436518664575E0)); -#30865=DIRECTION('',(0.E0,0.E0,1.E0)); -#30866=DIRECTION('',(1.E0,0.E0,0.E0)); -#30867=AXIS2_PLACEMENT_3D('',#30864,#30865,#30866); -#30868=PLANE('',#30867); -#30869=ORIENTED_EDGE('',*,*,#24644,.F.); -#30871=ORIENTED_EDGE('',*,*,#30870,.T.); -#30872=ORIENTED_EDGE('',*,*,#27619,.T.); -#30873=ORIENTED_EDGE('',*,*,#30857,.F.); -#30874=EDGE_LOOP('',(#30869,#30871,#30872,#30873)); -#30875=FACE_OUTER_BOUND('',#30874,.F.); -#30877=CARTESIAN_POINT('',(1.148936152458E0,1.55E0,6.380178470356E0)); -#30878=DIRECTION('',(-2.559765630612E-1,0.E0,9.666829879352E-1)); -#30879=DIRECTION('',(9.666829879352E-1,0.E0,2.559765630612E-1)); -#30880=AXIS2_PLACEMENT_3D('',#30877,#30878,#30879); -#30881=PLANE('',#30880); -#30882=ORIENTED_EDGE('',*,*,#24642,.F.); -#30884=ORIENTED_EDGE('',*,*,#30883,.T.); -#30885=ORIENTED_EDGE('',*,*,#27621,.T.); -#30886=ORIENTED_EDGE('',*,*,#30870,.F.); -#30887=EDGE_LOOP('',(#30882,#30884,#30885,#30886)); -#30888=FACE_OUTER_BOUND('',#30887,.F.); -#30890=CARTESIAN_POINT('',(1.021276593208E0,1.55E0,6.267498081918E0)); -#30891=DIRECTION('',(-6.617523905385E-1,0.E0,7.497224643937E-1)); -#30892=DIRECTION('',(7.497224643937E-1,0.E0,6.617523905385E-1)); -#30893=AXIS2_PLACEMENT_3D('',#30890,#30891,#30892); -#30894=PLANE('',#30893); -#30895=ORIENTED_EDGE('',*,*,#24640,.F.); -#30896=ORIENTED_EDGE('',*,*,#30469,.T.); -#30897=ORIENTED_EDGE('',*,*,#27623,.T.); -#30898=ORIENTED_EDGE('',*,*,#30883,.F.); -#30899=EDGE_LOOP('',(#30895,#30896,#30897,#30898)); -#30900=FACE_OUTER_BOUND('',#30899,.F.); -#30902=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.985796627250E0)); -#30903=DIRECTION('',(-9.355134834807E-1,0.E0,-3.532909880337E-1)); -#30904=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#30905=AXIS2_PLACEMENT_3D('',#30902,#30903,#30904); -#30906=PLANE('',#30905); -#30907=ORIENTED_EDGE('',*,*,#26390,.F.); -#30909=ORIENTED_EDGE('',*,*,#30908,.T.); -#30910=ORIENTED_EDGE('',*,*,#27627,.T.); -#30912=ORIENTED_EDGE('',*,*,#30911,.F.); -#30913=EDGE_LOOP('',(#30907,#30909,#30910,#30912)); -#30914=FACE_OUTER_BOUND('',#30913,.F.); -#30916=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.873116238812E0)); -#30917=DIRECTION('',(-1.E0,0.E0,0.E0)); -#30918=DIRECTION('',(0.E0,0.E0,1.E0)); -#30919=AXIS2_PLACEMENT_3D('',#30916,#30917,#30918); -#30920=PLANE('',#30919); -#30921=ORIENTED_EDGE('',*,*,#26420,.F.); -#30923=ORIENTED_EDGE('',*,*,#30922,.T.); -#30924=ORIENTED_EDGE('',*,*,#27629,.T.); -#30925=ORIENTED_EDGE('',*,*,#30908,.F.); -#30926=EDGE_LOOP('',(#30921,#30923,#30924,#30925)); -#30927=FACE_OUTER_BOUND('',#30926,.F.); -#30929=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,5.760435850374E0)); -#30930=DIRECTION('',(-9.355131494108E-1,0.E0,3.532918726485E-1)); -#30931=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#30932=AXIS2_PLACEMENT_3D('',#30929,#30930,#30931); -#30933=PLANE('',#30932); -#30934=ORIENTED_EDGE('',*,*,#26418,.F.); -#30936=ORIENTED_EDGE('',*,*,#30935,.T.); -#30937=ORIENTED_EDGE('',*,*,#27631,.T.); -#30938=ORIENTED_EDGE('',*,*,#30922,.F.); -#30939=EDGE_LOOP('',(#30934,#30936,#30937,#30938)); -#30940=FACE_OUTER_BOUND('',#30939,.F.); -#30942=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.647755139554E0)); -#30943=DIRECTION('',(-7.979700564663E-1,0.E0,6.026970955489E-1)); -#30944=DIRECTION('',(6.026970955489E-1,0.E0,7.979700564663E-1)); -#30945=AXIS2_PLACEMENT_3D('',#30942,#30943,#30944); -#30946=PLANE('',#30945); -#30947=ORIENTED_EDGE('',*,*,#26416,.F.); -#30949=ORIENTED_EDGE('',*,*,#30948,.T.); -#30950=ORIENTED_EDGE('',*,*,#27633,.T.); -#30951=ORIENTED_EDGE('',*,*,#30935,.F.); -#30952=EDGE_LOOP('',(#30947,#30949,#30950,#30951)); -#30953=FACE_OUTER_BOUND('',#30952,.F.); -#30955=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,5.563244767630E0)); -#30956=DIRECTION('',(-4.447027957437E-1,0.E0,8.956781919070E-1)); -#30957=DIRECTION('',(8.956781919070E-1,0.E0,4.447027957437E-1)); -#30958=AXIS2_PLACEMENT_3D('',#30955,#30956,#30957); -#30959=PLANE('',#30958); -#30960=ORIENTED_EDGE('',*,*,#26414,.F.); -#30962=ORIENTED_EDGE('',*,*,#30961,.T.); -#30963=ORIENTED_EDGE('',*,*,#27635,.T.); -#30964=ORIENTED_EDGE('',*,*,#30948,.F.); -#30965=EDGE_LOOP('',(#30960,#30962,#30963,#30964)); -#30966=FACE_OUTER_BOUND('',#30965,.F.); -#30968=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,5.563244767630E0)); -#30969=DIRECTION('',(0.E0,0.E0,1.E0)); -#30970=DIRECTION('',(1.E0,0.E0,0.E0)); -#30971=AXIS2_PLACEMENT_3D('',#30968,#30969,#30970); -#30972=PLANE('',#30971); -#30973=ORIENTED_EDGE('',*,*,#26412,.F.); -#30975=ORIENTED_EDGE('',*,*,#30974,.T.); -#30976=ORIENTED_EDGE('',*,*,#27637,.T.); -#30977=ORIENTED_EDGE('',*,*,#30961,.F.); -#30978=EDGE_LOOP('',(#30973,#30975,#30976,#30977)); -#30979=FACE_OUTER_BOUND('',#30978,.F.); -#30981=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,5.647755139554E0)); -#30982=DIRECTION('',(4.447027332794E-1,0.E0,8.956782229204E-1)); -#30983=DIRECTION('',(8.956782229204E-1,0.E0,-4.447027332794E-1)); -#30984=AXIS2_PLACEMENT_3D('',#30981,#30982,#30983); -#30985=PLANE('',#30984); -#30986=ORIENTED_EDGE('',*,*,#26410,.F.); -#30988=ORIENTED_EDGE('',*,*,#30987,.T.); -#30989=ORIENTED_EDGE('',*,*,#27639,.T.); -#30990=ORIENTED_EDGE('',*,*,#30974,.F.); -#30991=EDGE_LOOP('',(#30986,#30988,#30989,#30990)); -#30992=FACE_OUTER_BOUND('',#30991,.F.); -#30994=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,5.760435850374E0)); -#30995=DIRECTION('',(7.979700564663E-1,0.E0,6.026970955489E-1)); -#30996=DIRECTION('',(6.026970955489E-1,0.E0,-7.979700564663E-1)); -#30997=AXIS2_PLACEMENT_3D('',#30994,#30995,#30996); -#30998=PLANE('',#30997); -#30999=ORIENTED_EDGE('',*,*,#26408,.F.); -#31001=ORIENTED_EDGE('',*,*,#31000,.T.); -#31002=ORIENTED_EDGE('',*,*,#27641,.T.); -#31003=ORIENTED_EDGE('',*,*,#30987,.F.); -#31004=EDGE_LOOP('',(#30999,#31001,#31002,#31003)); -#31005=FACE_OUTER_BOUND('',#31004,.F.); -#31007=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.873116238812E0)); -#31008=DIRECTION('',(9.355131494108E-1,0.E0,3.532918726485E-1)); -#31009=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#31010=AXIS2_PLACEMENT_3D('',#31007,#31008,#31009); -#31011=PLANE('',#31010); -#31012=ORIENTED_EDGE('',*,*,#26406,.F.); -#31014=ORIENTED_EDGE('',*,*,#31013,.T.); -#31015=ORIENTED_EDGE('',*,*,#27643,.T.); -#31016=ORIENTED_EDGE('',*,*,#31000,.F.); -#31017=EDGE_LOOP('',(#31012,#31014,#31015,#31016)); -#31018=FACE_OUTER_BOUND('',#31017,.F.); -#31020=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,5.985796627250E0)); -#31021=DIRECTION('',(1.E0,0.E0,0.E0)); -#31022=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31023=AXIS2_PLACEMENT_3D('',#31020,#31021,#31022); -#31024=PLANE('',#31023); -#31025=ORIENTED_EDGE('',*,*,#26404,.F.); -#31027=ORIENTED_EDGE('',*,*,#31026,.T.); -#31028=ORIENTED_EDGE('',*,*,#27645,.T.); -#31029=ORIENTED_EDGE('',*,*,#31013,.F.); -#31030=EDGE_LOOP('',(#31025,#31027,#31028,#31029)); -#31031=FACE_OUTER_BOUND('',#31030,.F.); -#31033=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,6.098477338070E0)); -#31034=DIRECTION('',(9.355134834807E-1,0.E0,-3.532909880337E-1)); -#31035=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#31036=AXIS2_PLACEMENT_3D('',#31033,#31034,#31035); -#31037=PLANE('',#31036); -#31038=ORIENTED_EDGE('',*,*,#26402,.F.); -#31040=ORIENTED_EDGE('',*,*,#31039,.T.); -#31041=ORIENTED_EDGE('',*,*,#27647,.T.); -#31042=ORIENTED_EDGE('',*,*,#31026,.F.); -#31043=EDGE_LOOP('',(#31038,#31040,#31041,#31042)); -#31044=FACE_OUTER_BOUND('',#31043,.F.); -#31046=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,6.211157726508E0)); -#31047=DIRECTION('',(7.979692271762E-1,0.E0,-6.026981935263E-1)); -#31048=DIRECTION('',(-6.026981935263E-1,0.E0,-7.979692271762E-1)); -#31049=AXIS2_PLACEMENT_3D('',#31046,#31047,#31048); -#31050=PLANE('',#31049); -#31051=ORIENTED_EDGE('',*,*,#26400,.F.); -#31053=ORIENTED_EDGE('',*,*,#31052,.T.); -#31054=ORIENTED_EDGE('',*,*,#27649,.T.); -#31055=ORIENTED_EDGE('',*,*,#31039,.F.); -#31056=EDGE_LOOP('',(#31051,#31053,#31054,#31055)); -#31057=FACE_OUTER_BOUND('',#31056,.F.); -#31059=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,6.295668098432E0)); -#31060=DIRECTION('',(4.447027332794E-1,0.E0,-8.956782229204E-1)); -#31061=DIRECTION('',(-8.956782229204E-1,0.E0,-4.447027332794E-1)); -#31062=AXIS2_PLACEMENT_3D('',#31059,#31060,#31061); -#31063=PLANE('',#31062); -#31064=ORIENTED_EDGE('',*,*,#26398,.F.); -#31066=ORIENTED_EDGE('',*,*,#31065,.T.); -#31067=ORIENTED_EDGE('',*,*,#27651,.T.); -#31068=ORIENTED_EDGE('',*,*,#31052,.F.); -#31069=EDGE_LOOP('',(#31064,#31066,#31067,#31068)); -#31070=FACE_OUTER_BOUND('',#31069,.F.); -#31072=CARTESIAN_POINT('',(1.489361703396E0,1.55E0,6.295668098432E0)); -#31073=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31074=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31075=AXIS2_PLACEMENT_3D('',#31072,#31073,#31074); -#31076=PLANE('',#31075); -#31077=ORIENTED_EDGE('',*,*,#26396,.F.); -#31079=ORIENTED_EDGE('',*,*,#31078,.T.); -#31080=ORIENTED_EDGE('',*,*,#27653,.T.); -#31081=ORIENTED_EDGE('',*,*,#31065,.F.); -#31082=EDGE_LOOP('',(#31077,#31079,#31080,#31081)); -#31083=FACE_OUTER_BOUND('',#31082,.F.); -#31085=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,6.211157726508E0)); -#31086=DIRECTION('',(-4.447027957437E-1,0.E0,-8.956781919070E-1)); -#31087=DIRECTION('',(-8.956781919070E-1,0.E0,4.447027957437E-1)); -#31088=AXIS2_PLACEMENT_3D('',#31085,#31086,#31087); -#31089=PLANE('',#31088); -#31090=ORIENTED_EDGE('',*,*,#26394,.F.); -#31092=ORIENTED_EDGE('',*,*,#31091,.T.); -#31093=ORIENTED_EDGE('',*,*,#27655,.T.); -#31094=ORIENTED_EDGE('',*,*,#31078,.F.); -#31095=EDGE_LOOP('',(#31090,#31092,#31093,#31094)); -#31096=FACE_OUTER_BOUND('',#31095,.F.); -#31098=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,6.098477338070E0)); -#31099=DIRECTION('',(-7.979692271762E-1,0.E0,-6.026981935263E-1)); -#31100=DIRECTION('',(-6.026981935263E-1,0.E0,7.979692271762E-1)); -#31101=AXIS2_PLACEMENT_3D('',#31098,#31099,#31100); -#31102=PLANE('',#31101); -#31103=ORIENTED_EDGE('',*,*,#26392,.F.); -#31104=ORIENTED_EDGE('',*,*,#30911,.T.); -#31105=ORIENTED_EDGE('',*,*,#27657,.T.); -#31106=ORIENTED_EDGE('',*,*,#31091,.F.); -#31107=EDGE_LOOP('',(#31103,#31104,#31105,#31106)); -#31108=FACE_OUTER_BOUND('',#31107,.F.); -#31110=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.873116238812E0)); -#31111=DIRECTION('',(9.355131494108E-1,0.E0,3.532918726485E-1)); -#31112=DIRECTION('',(3.532918726485E-1,0.E0,-9.355131494108E-1)); -#31113=AXIS2_PLACEMENT_3D('',#31110,#31111,#31112); -#31114=PLANE('',#31113); -#31115=ORIENTED_EDGE('',*,*,#26430,.F.); -#31117=ORIENTED_EDGE('',*,*,#31116,.T.); -#31118=ORIENTED_EDGE('',*,*,#27661,.T.); -#31120=ORIENTED_EDGE('',*,*,#31119,.F.); -#31121=EDGE_LOOP('',(#31115,#31117,#31118,#31120)); -#31122=FACE_OUTER_BOUND('',#31121,.F.); -#31124=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,5.985796627250E0)); -#31125=DIRECTION('',(1.E0,0.E0,0.E0)); -#31126=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31127=AXIS2_PLACEMENT_3D('',#31124,#31125,#31126); -#31128=PLANE('',#31127); -#31129=ORIENTED_EDGE('',*,*,#26460,.F.); -#31131=ORIENTED_EDGE('',*,*,#31130,.T.); -#31132=ORIENTED_EDGE('',*,*,#27663,.T.); -#31133=ORIENTED_EDGE('',*,*,#31116,.F.); -#31134=EDGE_LOOP('',(#31129,#31131,#31132,#31133)); -#31135=FACE_OUTER_BOUND('',#31134,.F.); -#31137=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,6.098477338070E0)); -#31138=DIRECTION('',(9.355134834807E-1,0.E0,-3.532909880337E-1)); -#31139=DIRECTION('',(-3.532909880337E-1,0.E0,-9.355134834807E-1)); -#31140=AXIS2_PLACEMENT_3D('',#31137,#31138,#31139); -#31141=PLANE('',#31140); -#31142=ORIENTED_EDGE('',*,*,#26458,.F.); -#31144=ORIENTED_EDGE('',*,*,#31143,.T.); -#31145=ORIENTED_EDGE('',*,*,#27665,.T.); -#31146=ORIENTED_EDGE('',*,*,#31130,.F.); -#31147=EDGE_LOOP('',(#31142,#31144,#31145,#31146)); -#31148=FACE_OUTER_BOUND('',#31147,.F.); -#31150=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,6.211157726508E0)); -#31151=DIRECTION('',(6.617523905385E-1,0.E0,-7.497224643937E-1)); -#31152=DIRECTION('',(-7.497224643937E-1,0.E0,-6.617523905385E-1)); -#31153=AXIS2_PLACEMENT_3D('',#31150,#31151,#31152); -#31154=PLANE('',#31153); -#31155=ORIENTED_EDGE('',*,*,#26456,.F.); -#31157=ORIENTED_EDGE('',*,*,#31156,.T.); -#31158=ORIENTED_EDGE('',*,*,#27667,.T.); -#31159=ORIENTED_EDGE('',*,*,#31143,.F.); -#31160=EDGE_LOOP('',(#31155,#31157,#31158,#31159)); -#31161=FACE_OUTER_BOUND('',#31160,.F.); -#31163=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,6.267498081918E0)); -#31164=DIRECTION('',(4.037596342805E-1,0.E0,-9.148651035675E-1)); -#31165=DIRECTION('',(-9.148651035675E-1,0.E0,-4.037596342805E-1)); -#31166=AXIS2_PLACEMENT_3D('',#31163,#31164,#31165); -#31167=PLANE('',#31166); -#31168=ORIENTED_EDGE('',*,*,#26454,.F.); -#31170=ORIENTED_EDGE('',*,*,#31169,.T.); -#31171=ORIENTED_EDGE('',*,*,#27669,.T.); -#31172=ORIENTED_EDGE('',*,*,#31156,.F.); -#31173=EDGE_LOOP('',(#31168,#31170,#31171,#31172)); -#31174=FACE_OUTER_BOUND('',#31173,.F.); -#31176=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,6.267498081918E0)); -#31177=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31178=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31179=AXIS2_PLACEMENT_3D('',#31176,#31177,#31178); -#31180=PLANE('',#31179); -#31181=ORIENTED_EDGE('',*,*,#26452,.F.); -#31183=ORIENTED_EDGE('',*,*,#31182,.T.); -#31184=ORIENTED_EDGE('',*,*,#27671,.T.); -#31185=ORIENTED_EDGE('',*,*,#31169,.F.); -#31186=EDGE_LOOP('',(#31181,#31183,#31184,#31185)); -#31187=FACE_OUTER_BOUND('',#31186,.F.); -#31189=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,6.211157726508E0)); -#31190=DIRECTION('',(-4.037599498491E-1,0.E0,-9.148649642969E-1)); -#31191=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498491E-1)); -#31192=AXIS2_PLACEMENT_3D('',#31189,#31190,#31191); -#31193=PLANE('',#31192); -#31194=ORIENTED_EDGE('',*,*,#26450,.F.); -#31196=ORIENTED_EDGE('',*,*,#31195,.T.); -#31197=ORIENTED_EDGE('',*,*,#27673,.T.); -#31198=ORIENTED_EDGE('',*,*,#31182,.F.); -#31199=EDGE_LOOP('',(#31194,#31196,#31197,#31198)); -#31200=FACE_OUTER_BOUND('',#31199,.F.); -#31202=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,6.098477338070E0)); -#31203=DIRECTION('',(-6.617523905385E-1,0.E0,-7.497224643937E-1)); -#31204=DIRECTION('',(-7.497224643937E-1,0.E0,6.617523905385E-1)); -#31205=AXIS2_PLACEMENT_3D('',#31202,#31203,#31204); -#31206=PLANE('',#31205); -#31207=ORIENTED_EDGE('',*,*,#26448,.F.); -#31209=ORIENTED_EDGE('',*,*,#31208,.T.); -#31210=ORIENTED_EDGE('',*,*,#27675,.T.); -#31211=ORIENTED_EDGE('',*,*,#31195,.F.); -#31212=EDGE_LOOP('',(#31207,#31209,#31210,#31211)); -#31213=FACE_OUTER_BOUND('',#31212,.F.); -#31215=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.985796627250E0)); -#31216=DIRECTION('',(-9.355134834807E-1,0.E0,-3.532909880337E-1)); -#31217=DIRECTION('',(-3.532909880337E-1,0.E0,9.355134834807E-1)); -#31218=AXIS2_PLACEMENT_3D('',#31215,#31216,#31217); -#31219=PLANE('',#31218); -#31220=ORIENTED_EDGE('',*,*,#26446,.F.); -#31222=ORIENTED_EDGE('',*,*,#31221,.T.); -#31223=ORIENTED_EDGE('',*,*,#27677,.T.); -#31224=ORIENTED_EDGE('',*,*,#31208,.F.); -#31225=EDGE_LOOP('',(#31220,#31222,#31223,#31224)); -#31226=FACE_OUTER_BOUND('',#31225,.F.); -#31228=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,5.873116238812E0)); -#31229=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31230=DIRECTION('',(0.E0,0.E0,1.E0)); -#31231=AXIS2_PLACEMENT_3D('',#31228,#31229,#31230); -#31232=PLANE('',#31231); -#31233=ORIENTED_EDGE('',*,*,#26444,.F.); -#31235=ORIENTED_EDGE('',*,*,#31234,.T.); -#31236=ORIENTED_EDGE('',*,*,#27679,.T.); -#31237=ORIENTED_EDGE('',*,*,#31221,.F.); -#31238=EDGE_LOOP('',(#31233,#31235,#31236,#31237)); -#31239=FACE_OUTER_BOUND('',#31238,.F.); -#31241=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,5.760435850374E0)); -#31242=DIRECTION('',(-9.355131494108E-1,0.E0,3.532918726485E-1)); -#31243=DIRECTION('',(3.532918726485E-1,0.E0,9.355131494108E-1)); -#31244=AXIS2_PLACEMENT_3D('',#31241,#31242,#31243); -#31245=PLANE('',#31244); -#31246=ORIENTED_EDGE('',*,*,#26442,.F.); -#31248=ORIENTED_EDGE('',*,*,#31247,.T.); -#31249=ORIENTED_EDGE('',*,*,#27681,.T.); -#31250=ORIENTED_EDGE('',*,*,#31234,.F.); -#31251=EDGE_LOOP('',(#31246,#31248,#31249,#31250)); -#31252=FACE_OUTER_BOUND('',#31251,.F.); -#31254=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,5.647755139554E0)); -#31255=DIRECTION('',(-6.617534547244E-1,0.E0,7.497215250747E-1)); -#31256=DIRECTION('',(7.497215250747E-1,0.E0,6.617534547244E-1)); -#31257=AXIS2_PLACEMENT_3D('',#31254,#31255,#31256); -#31258=PLANE('',#31257); -#31259=ORIENTED_EDGE('',*,*,#26440,.F.); -#31261=ORIENTED_EDGE('',*,*,#31260,.T.); -#31262=ORIENTED_EDGE('',*,*,#27683,.T.); -#31263=ORIENTED_EDGE('',*,*,#31247,.F.); -#31264=EDGE_LOOP('',(#31259,#31261,#31262,#31263)); -#31265=FACE_OUTER_BOUND('',#31264,.F.); -#31267=CARTESIAN_POINT('',(5.957447290421E-1,1.55E0,5.591415106526E0)); -#31268=DIRECTION('',(-4.037580161524E-1,0.E0,9.148658176982E-1)); -#31269=DIRECTION('',(9.148658176982E-1,0.E0,4.037580161524E-1)); -#31270=AXIS2_PLACEMENT_3D('',#31267,#31268,#31269); -#31271=PLANE('',#31270); -#31272=ORIENTED_EDGE('',*,*,#26438,.F.); -#31274=ORIENTED_EDGE('',*,*,#31273,.T.); -#31275=ORIENTED_EDGE('',*,*,#27685,.T.); -#31276=ORIENTED_EDGE('',*,*,#31260,.F.); -#31277=EDGE_LOOP('',(#31272,#31274,#31275,#31276)); -#31278=FACE_OUTER_BOUND('',#31277,.F.); -#31280=CARTESIAN_POINT('',(5.106383562088E-1,1.55E0,5.591415106526E0)); -#31281=DIRECTION('',(0.E0,0.E0,1.E0)); -#31282=DIRECTION('',(1.E0,0.E0,0.E0)); -#31283=AXIS2_PLACEMENT_3D('',#31280,#31281,#31282); -#31284=PLANE('',#31283); -#31285=ORIENTED_EDGE('',*,*,#26436,.F.); -#31287=ORIENTED_EDGE('',*,*,#31286,.T.); -#31288=ORIENTED_EDGE('',*,*,#27687,.T.); -#31289=ORIENTED_EDGE('',*,*,#31273,.F.); -#31290=EDGE_LOOP('',(#31285,#31287,#31288,#31289)); -#31291=FACE_OUTER_BOUND('',#31290,.F.); -#31293=CARTESIAN_POINT('',(3.829786777496E-1,1.55E0,5.647755139554E0)); -#31294=DIRECTION('',(4.037577005848E-1,0.E0,9.148659569677E-1)); -#31295=DIRECTION('',(9.148659569677E-1,0.E0,-4.037577005848E-1)); -#31296=AXIS2_PLACEMENT_3D('',#31293,#31294,#31295); -#31297=PLANE('',#31296); -#31298=ORIENTED_EDGE('',*,*,#26434,.F.); -#31300=ORIENTED_EDGE('',*,*,#31299,.T.); -#31301=ORIENTED_EDGE('',*,*,#27689,.T.); -#31302=ORIENTED_EDGE('',*,*,#31286,.F.); -#31303=EDGE_LOOP('',(#31298,#31300,#31301,#31302)); -#31304=FACE_OUTER_BOUND('',#31303,.F.); -#31306=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,5.760435850374E0)); -#31307=DIRECTION('',(6.617534547244E-1,0.E0,7.497215250747E-1)); -#31308=DIRECTION('',(7.497215250747E-1,0.E0,-6.617534547244E-1)); -#31309=AXIS2_PLACEMENT_3D('',#31306,#31307,#31308); -#31310=PLANE('',#31309); -#31311=ORIENTED_EDGE('',*,*,#26432,.F.); -#31312=ORIENTED_EDGE('',*,*,#31119,.T.); -#31313=ORIENTED_EDGE('',*,*,#27691,.T.); -#31314=ORIENTED_EDGE('',*,*,#31299,.F.); -#31315=EDGE_LOOP('',(#31311,#31312,#31313,#31314)); -#31316=FACE_OUTER_BOUND('',#31315,.F.); -#31318=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.267419172256E0)); -#31319=DIRECTION('',(4.037599498491E-1,0.E0,-9.148649642969E-1)); -#31320=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498491E-1)); -#31321=AXIS2_PLACEMENT_3D('',#31318,#31319,#31320); -#31322=PLANE('',#31321); -#31323=ORIENTED_EDGE('',*,*,#24708,.F.); -#31325=ORIENTED_EDGE('',*,*,#31324,.T.); -#31326=ORIENTED_EDGE('',*,*,#27708,.T.); -#31328=ORIENTED_EDGE('',*,*,#31327,.F.); -#31329=EDGE_LOOP('',(#31323,#31325,#31326,#31328)); -#31330=FACE_OUTER_BOUND('',#31329,.F.); -#31332=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,4.351929544180E0)); -#31333=DIRECTION('',(7.046177307313E-1,0.E0,-7.095871007418E-1)); -#31334=DIRECTION('',(-7.095871007418E-1,0.E0,-7.046177307313E-1)); -#31335=AXIS2_PLACEMENT_3D('',#31332,#31333,#31334); -#31336=PLANE('',#31335); -#31337=ORIENTED_EDGE('',*,*,#24820,.F.); -#31339=ORIENTED_EDGE('',*,*,#31338,.T.); -#31340=ORIENTED_EDGE('',*,*,#27710,.T.); -#31341=ORIENTED_EDGE('',*,*,#31324,.F.); -#31342=EDGE_LOOP('',(#31337,#31339,#31340,#31341)); -#31343=FACE_OUTER_BOUND('',#31342,.F.); -#31345=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.464609932618E0)); -#31346=DIRECTION('',(7.979691891130E-1,0.E0,-6.026982439217E-1)); -#31347=DIRECTION('',(-6.026982439217E-1,0.E0,-7.979691891130E-1)); -#31348=AXIS2_PLACEMENT_3D('',#31345,#31346,#31347); -#31349=PLANE('',#31348); -#31350=ORIENTED_EDGE('',*,*,#24818,.F.); -#31352=ORIENTED_EDGE('',*,*,#31351,.T.); -#31353=ORIENTED_EDGE('',*,*,#27712,.T.); -#31354=ORIENTED_EDGE('',*,*,#31338,.F.); -#31355=EDGE_LOOP('',(#31350,#31352,#31353,#31354)); -#31356=FACE_OUTER_BOUND('',#31355,.F.); -#31358=CARTESIAN_POINT('',(2.E0,1.55E0,4.577290643438E0)); -#31359=DIRECTION('',(9.355134732585E-1,0.E0,-3.532910151020E-1)); -#31360=DIRECTION('',(-3.532910151020E-1,0.E0,-9.355134732585E-1)); -#31361=AXIS2_PLACEMENT_3D('',#31358,#31359,#31360); -#31362=PLANE('',#31361); -#31363=ORIENTED_EDGE('',*,*,#24816,.F.); -#31365=ORIENTED_EDGE('',*,*,#31364,.T.); -#31366=ORIENTED_EDGE('',*,*,#27714,.T.); -#31367=ORIENTED_EDGE('',*,*,#31351,.F.); -#31368=EDGE_LOOP('',(#31363,#31365,#31366,#31367)); -#31369=FACE_OUTER_BOUND('',#31368,.F.); -#31371=CARTESIAN_POINT('',(2.E0,1.55E0,4.802651420314E0)); -#31372=DIRECTION('',(1.E0,0.E0,0.E0)); -#31373=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31374=AXIS2_PLACEMENT_3D('',#31371,#31372,#31373); -#31375=PLANE('',#31374); -#31376=ORIENTED_EDGE('',*,*,#24814,.F.); -#31378=ORIENTED_EDGE('',*,*,#31377,.T.); -#31379=ORIENTED_EDGE('',*,*,#27716,.T.); -#31380=ORIENTED_EDGE('',*,*,#31364,.F.); -#31381=EDGE_LOOP('',(#31376,#31378,#31379,#31380)); -#31382=FACE_OUTER_BOUND('',#31381,.F.); -#31384=CARTESIAN_POINT('',(1.957446809858E0,1.55E0,4.915332131134E0)); -#31385=DIRECTION('',(9.355134732585E-1,0.E0,3.532910151020E-1)); -#31386=DIRECTION('',(3.532910151020E-1,0.E0,-9.355134732585E-1)); -#31387=AXIS2_PLACEMENT_3D('',#31384,#31385,#31386); -#31388=PLANE('',#31387); -#31389=ORIENTED_EDGE('',*,*,#24812,.F.); -#31391=ORIENTED_EDGE('',*,*,#31390,.T.); -#31392=ORIENTED_EDGE('',*,*,#27718,.T.); -#31393=ORIENTED_EDGE('',*,*,#31377,.F.); -#31394=EDGE_LOOP('',(#31389,#31391,#31392,#31393)); -#31395=FACE_OUTER_BOUND('',#31394,.F.); -#31397=CARTESIAN_POINT('',(1.872340425849E0,1.55E0,5.028012519572E0)); -#31398=DIRECTION('',(7.979691891130E-1,0.E0,6.026982439217E-1)); -#31399=DIRECTION('',(6.026982439217E-1,0.E0,-7.979691891130E-1)); -#31400=AXIS2_PLACEMENT_3D('',#31397,#31398,#31399); -#31401=PLANE('',#31400); -#31402=ORIENTED_EDGE('',*,*,#24810,.F.); -#31404=ORIENTED_EDGE('',*,*,#31403,.T.); -#31405=ORIENTED_EDGE('',*,*,#27720,.T.); -#31406=ORIENTED_EDGE('',*,*,#31390,.F.); -#31407=EDGE_LOOP('',(#31402,#31404,#31405,#31406)); -#31408=FACE_OUTER_BOUND('',#31407,.F.); -#31410=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,5.112522891496E0)); -#31411=DIRECTION('',(7.046177307313E-1,0.E0,7.095871007418E-1)); -#31412=DIRECTION('',(7.095871007418E-1,0.E0,-7.046177307313E-1)); -#31413=AXIS2_PLACEMENT_3D('',#31410,#31411,#31412); -#31414=PLANE('',#31413); -#31415=ORIENTED_EDGE('',*,*,#24808,.F.); -#31417=ORIENTED_EDGE('',*,*,#31416,.T.); -#31418=ORIENTED_EDGE('',*,*,#27722,.T.); -#31419=ORIENTED_EDGE('',*,*,#31403,.F.); -#31420=EDGE_LOOP('',(#31415,#31417,#31418,#31419)); -#31421=FACE_OUTER_BOUND('',#31420,.F.); -#31423=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,5.168863246906E0)); -#31424=DIRECTION('',(4.037599498491E-1,0.E0,9.148649642969E-1)); -#31425=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#31426=AXIS2_PLACEMENT_3D('',#31423,#31424,#31425); -#31427=PLANE('',#31426); -#31428=ORIENTED_EDGE('',*,*,#24806,.F.); -#31430=ORIENTED_EDGE('',*,*,#31429,.T.); -#31431=ORIENTED_EDGE('',*,*,#27724,.T.); -#31432=ORIENTED_EDGE('',*,*,#31416,.F.); -#31433=EDGE_LOOP('',(#31428,#31430,#31431,#31432)); -#31434=FACE_OUTER_BOUND('',#31433,.F.); -#31436=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.197033263420E0)); -#31437=DIRECTION('',(2.154812353607E-1,0.E0,9.765079811284E-1)); -#31438=DIRECTION('',(9.765079811284E-1,0.E0,-2.154812353607E-1)); -#31439=AXIS2_PLACEMENT_3D('',#31436,#31437,#31438); -#31440=PLANE('',#31439); -#31441=ORIENTED_EDGE('',*,*,#24804,.F.); -#31443=ORIENTED_EDGE('',*,*,#31442,.T.); -#31444=ORIENTED_EDGE('',*,*,#27726,.T.); -#31445=ORIENTED_EDGE('',*,*,#31429,.F.); -#31446=EDGE_LOOP('',(#31441,#31443,#31444,#31445)); -#31447=FACE_OUTER_BOUND('',#31446,.F.); -#31449=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,5.056182536086E0)); -#31450=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31451=DIRECTION('',(0.E0,0.E0,1.E0)); -#31452=AXIS2_PLACEMENT_3D('',#31449,#31450,#31451); -#31453=PLANE('',#31452); -#31454=ORIENTED_EDGE('',*,*,#24802,.F.); -#31456=ORIENTED_EDGE('',*,*,#31455,.T.); -#31457=ORIENTED_EDGE('',*,*,#27728,.T.); -#31458=ORIENTED_EDGE('',*,*,#31442,.F.); -#31459=EDGE_LOOP('',(#31454,#31456,#31457,#31458)); -#31460=FACE_OUTER_BOUND('',#31459,.F.); -#31462=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,5.028012519572E0)); -#31463=DIRECTION('',(-3.142315024639E-1,0.E0,-9.493463871840E-1)); -#31464=DIRECTION('',(-9.493463871840E-1,0.E0,3.142315024639E-1)); -#31465=AXIS2_PLACEMENT_3D('',#31462,#31463,#31464); -#31466=PLANE('',#31465); -#31467=ORIENTED_EDGE('',*,*,#24800,.F.); -#31469=ORIENTED_EDGE('',*,*,#31468,.T.); -#31470=ORIENTED_EDGE('',*,*,#27730,.T.); -#31471=ORIENTED_EDGE('',*,*,#31455,.F.); -#31472=EDGE_LOOP('',(#31467,#31469,#31470,#31471)); -#31473=FACE_OUTER_BOUND('',#31472,.F.); -#31475=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.971672164162E0)); -#31476=DIRECTION('',(-5.520027717038E-1,0.E0,-8.338422752723E-1)); -#31477=DIRECTION('',(-8.338422752723E-1,0.E0,5.520027717038E-1)); -#31478=AXIS2_PLACEMENT_3D('',#31475,#31476,#31477); -#31479=PLANE('',#31478); -#31480=ORIENTED_EDGE('',*,*,#24798,.F.); -#31482=ORIENTED_EDGE('',*,*,#31481,.T.); -#31483=ORIENTED_EDGE('',*,*,#27732,.T.); -#31484=ORIENTED_EDGE('',*,*,#31468,.F.); -#31485=EDGE_LOOP('',(#31480,#31482,#31483,#31484)); -#31486=FACE_OUTER_BOUND('',#31485,.F.); -#31488=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.915332131134E0)); -#31489=DIRECTION('',(-7.979683978816E-1,0.E0,-6.026992915064E-1)); -#31490=DIRECTION('',(-6.026992915064E-1,0.E0,7.979683978816E-1)); -#31491=AXIS2_PLACEMENT_3D('',#31488,#31489,#31490); -#31492=PLANE('',#31491); -#31493=ORIENTED_EDGE('',*,*,#24796,.F.); -#31495=ORIENTED_EDGE('',*,*,#31494,.T.); -#31496=ORIENTED_EDGE('',*,*,#27734,.T.); -#31497=ORIENTED_EDGE('',*,*,#31481,.F.); -#31498=EDGE_LOOP('',(#31493,#31495,#31496,#31497)); -#31499=FACE_OUTER_BOUND('',#31498,.F.); -#31501=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.774481403800E0)); -#31502=DIRECTION('',(-9.572671195869E-1,0.E0,-2.892052242921E-1)); -#31503=DIRECTION('',(-2.892052242921E-1,0.E0,9.572671195869E-1)); -#31504=AXIS2_PLACEMENT_3D('',#31501,#31502,#31503); -#31505=PLANE('',#31504); -#31506=ORIENTED_EDGE('',*,*,#24794,.F.); -#31508=ORIENTED_EDGE('',*,*,#31507,.T.); -#31509=ORIENTED_EDGE('',*,*,#27736,.T.); -#31510=ORIENTED_EDGE('',*,*,#31494,.F.); -#31511=EDGE_LOOP('',(#31506,#31508,#31509,#31510)); -#31512=FACE_OUTER_BOUND('',#31511,.F.); -#31514=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,4.605460659952E0)); -#31515=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31516=DIRECTION('',(0.E0,0.E0,1.E0)); -#31517=AXIS2_PLACEMENT_3D('',#31514,#31515,#31516); -#31518=PLANE('',#31517); -#31519=ORIENTED_EDGE('',*,*,#24792,.F.); -#31521=ORIENTED_EDGE('',*,*,#31520,.T.); -#31522=ORIENTED_EDGE('',*,*,#27738,.T.); -#31523=ORIENTED_EDGE('',*,*,#31507,.F.); -#31524=EDGE_LOOP('',(#31519,#31521,#31522,#31523)); -#31525=FACE_OUTER_BOUND('',#31524,.F.); -#31527=CARTESIAN_POINT('',(1.744680851698E0,1.55E0,4.464609932618E0)); -#31528=DIRECTION('',(-9.572671195869E-1,0.E0,2.892052242921E-1)); -#31529=DIRECTION('',(2.892052242921E-1,0.E0,9.572671195869E-1)); -#31530=AXIS2_PLACEMENT_3D('',#31527,#31528,#31529); -#31531=PLANE('',#31530); -#31532=ORIENTED_EDGE('',*,*,#24790,.F.); -#31534=ORIENTED_EDGE('',*,*,#31533,.T.); -#31535=ORIENTED_EDGE('',*,*,#27740,.T.); -#31536=ORIENTED_EDGE('',*,*,#31520,.F.); -#31537=EDGE_LOOP('',(#31532,#31534,#31535,#31536)); -#31538=FACE_OUTER_BOUND('',#31537,.F.); -#31540=CARTESIAN_POINT('',(1.702127665281E0,1.55E0,4.408269899590E0)); -#31541=DIRECTION('',(-7.979683978816E-1,0.E0,6.026992915064E-1)); -#31542=DIRECTION('',(6.026992915064E-1,0.E0,7.979683978816E-1)); -#31543=AXIS2_PLACEMENT_3D('',#31540,#31541,#31542); -#31544=PLANE('',#31543); -#31545=ORIENTED_EDGE('',*,*,#24788,.F.); -#31547=ORIENTED_EDGE('',*,*,#31546,.T.); -#31548=ORIENTED_EDGE('',*,*,#27742,.T.); -#31549=ORIENTED_EDGE('',*,*,#31533,.F.); -#31550=EDGE_LOOP('',(#31545,#31547,#31548,#31549)); -#31551=FACE_OUTER_BOUND('',#31550,.F.); -#31553=CARTESIAN_POINT('',(1.617021262646E0,1.55E0,4.351929544180E0)); -#31554=DIRECTION('',(-5.520027717038E-1,0.E0,8.338422752723E-1)); -#31555=DIRECTION('',(8.338422752723E-1,0.E0,5.520027717038E-1)); -#31556=AXIS2_PLACEMENT_3D('',#31553,#31554,#31555); -#31557=PLANE('',#31556); -#31558=ORIENTED_EDGE('',*,*,#24786,.F.); -#31560=ORIENTED_EDGE('',*,*,#31559,.T.); -#31561=ORIENTED_EDGE('',*,*,#27744,.T.); -#31562=ORIENTED_EDGE('',*,*,#31546,.F.); -#31563=EDGE_LOOP('',(#31558,#31560,#31561,#31562)); -#31564=FACE_OUTER_BOUND('',#31563,.F.); -#31566=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.323759527666E0)); -#31567=DIRECTION('',(-3.142315024639E-1,0.E0,9.493463871840E-1)); -#31568=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#31569=AXIS2_PLACEMENT_3D('',#31566,#31567,#31568); -#31570=PLANE('',#31569); -#31571=ORIENTED_EDGE('',*,*,#24784,.F.); -#31573=ORIENTED_EDGE('',*,*,#31572,.T.); -#31574=ORIENTED_EDGE('',*,*,#27746,.T.); -#31575=ORIENTED_EDGE('',*,*,#31559,.F.); -#31576=EDGE_LOOP('',(#31571,#31573,#31574,#31575)); -#31577=FACE_OUTER_BOUND('',#31576,.F.); -#31579=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.323759527666E0)); -#31580=DIRECTION('',(0.E0,0.E0,1.E0)); -#31581=DIRECTION('',(1.E0,0.E0,0.E0)); -#31582=AXIS2_PLACEMENT_3D('',#31579,#31580,#31581); -#31583=PLANE('',#31582); -#31584=ORIENTED_EDGE('',*,*,#24782,.F.); -#31586=ORIENTED_EDGE('',*,*,#31585,.T.); -#31587=ORIENTED_EDGE('',*,*,#27748,.T.); -#31588=ORIENTED_EDGE('',*,*,#31572,.F.); -#31589=EDGE_LOOP('',(#31584,#31586,#31587,#31588)); -#31590=FACE_OUTER_BOUND('',#31589,.F.); -#31592=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.380099560694E0)); -#31593=DIRECTION('',(3.142314032923E-1,0.E0,9.493464200095E-1)); -#31594=DIRECTION('',(9.493464200095E-1,0.E0,-3.142314032923E-1)); -#31595=AXIS2_PLACEMENT_3D('',#31592,#31593,#31594); -#31596=PLANE('',#31595); -#31597=ORIENTED_EDGE('',*,*,#24780,.F.); -#31599=ORIENTED_EDGE('',*,*,#31598,.T.); -#31600=ORIENTED_EDGE('',*,*,#27750,.T.); -#31601=ORIENTED_EDGE('',*,*,#31585,.F.); -#31602=EDGE_LOOP('',(#31597,#31599,#31600,#31601)); -#31603=FACE_OUTER_BOUND('',#31602,.F.); -#31605=CARTESIAN_POINT('',(1.106382966042E0,1.55E0,4.464609932618E0)); -#31606=DIRECTION('',(7.046177928501E-1,0.E0,7.095870390580E-1)); -#31607=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#31608=AXIS2_PLACEMENT_3D('',#31605,#31606,#31607); -#31609=PLANE('',#31608); -#31610=ORIENTED_EDGE('',*,*,#24778,.F.); -#31612=ORIENTED_EDGE('',*,*,#31611,.T.); -#31613=ORIENTED_EDGE('',*,*,#27752,.T.); -#31614=ORIENTED_EDGE('',*,*,#31598,.F.); -#31615=EDGE_LOOP('',(#31610,#31612,#31613,#31614)); -#31616=FACE_OUTER_BOUND('',#31615,.F.); -#31618=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.633630676466E0)); -#31619=DIRECTION('',(9.697388722849E-1,0.E0,2.441444645688E-1)); -#31620=DIRECTION('',(2.441444645688E-1,0.E0,-9.697388722849E-1)); -#31621=AXIS2_PLACEMENT_3D('',#31618,#31619,#31620); -#31622=PLANE('',#31621); -#31623=ORIENTED_EDGE('',*,*,#24776,.F.); -#31625=ORIENTED_EDGE('',*,*,#31624,.T.); -#31626=ORIENTED_EDGE('',*,*,#27754,.T.); -#31627=ORIENTED_EDGE('',*,*,#31611,.F.); -#31628=EDGE_LOOP('',(#31623,#31625,#31626,#31627)); -#31629=FACE_OUTER_BOUND('',#31628,.F.); -#31631=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.746311387286E0)); -#31632=DIRECTION('',(1.E0,0.E0,0.E0)); -#31633=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31634=AXIS2_PLACEMENT_3D('',#31631,#31632,#31633); -#31635=PLANE('',#31634); -#31636=ORIENTED_EDGE('',*,*,#24774,.F.); -#31638=ORIENTED_EDGE('',*,*,#31637,.T.); -#31639=ORIENTED_EDGE('',*,*,#27756,.T.); -#31640=ORIENTED_EDGE('',*,*,#31624,.F.); -#31641=EDGE_LOOP('',(#31636,#31638,#31639,#31640)); -#31642=FACE_OUTER_BOUND('',#31641,.F.); -#31644=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.746311387286E0)); -#31645=DIRECTION('',(0.E0,0.E0,1.E0)); -#31646=DIRECTION('',(1.E0,0.E0,0.E0)); -#31647=AXIS2_PLACEMENT_3D('',#31644,#31645,#31646); -#31648=PLANE('',#31647); -#31649=ORIENTED_EDGE('',*,*,#24772,.F.); -#31651=ORIENTED_EDGE('',*,*,#31650,.T.); -#31652=ORIENTED_EDGE('',*,*,#27758,.T.); -#31653=ORIENTED_EDGE('',*,*,#31637,.F.); -#31654=EDGE_LOOP('',(#31649,#31651,#31652,#31653)); -#31655=FACE_OUTER_BOUND('',#31654,.F.); -#31657=CARTESIAN_POINT('',(8.936170339584E-1,1.55E0,4.633630676466E0)); -#31658=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31659=DIRECTION('',(0.E0,0.E0,1.E0)); -#31660=AXIS2_PLACEMENT_3D('',#31657,#31658,#31659); -#31661=PLANE('',#31660); -#31662=ORIENTED_EDGE('',*,*,#24770,.F.); -#31664=ORIENTED_EDGE('',*,*,#31663,.T.); -#31665=ORIENTED_EDGE('',*,*,#27760,.T.); -#31666=ORIENTED_EDGE('',*,*,#31650,.F.); -#31667=EDGE_LOOP('',(#31662,#31664,#31665,#31666)); -#31668=FACE_OUTER_BOUND('',#31667,.F.); -#31670=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,4.464609932618E0)); -#31671=DIRECTION('',(-8.931638525254E-1,0.E0,4.497314004403E-1)); -#31672=DIRECTION('',(4.497314004403E-1,0.E0,8.931638525254E-1)); -#31673=AXIS2_PLACEMENT_3D('',#31670,#31671,#31672); -#31674=PLANE('',#31673); -#31675=ORIENTED_EDGE('',*,*,#24768,.F.); -#31677=ORIENTED_EDGE('',*,*,#31676,.T.); -#31678=ORIENTED_EDGE('',*,*,#27762,.T.); -#31679=ORIENTED_EDGE('',*,*,#31663,.F.); -#31680=EDGE_LOOP('',(#31675,#31677,#31678,#31679)); -#31681=FACE_OUTER_BOUND('',#31680,.F.); -#31683=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.408269899590E0)); -#31684=DIRECTION('',(-5.520007099595E-1,0.E0,8.338436401413E-1)); -#31685=DIRECTION('',(8.338436401413E-1,0.E0,5.520007099595E-1)); -#31686=AXIS2_PLACEMENT_3D('',#31683,#31684,#31685); -#31687=PLANE('',#31686); -#31688=ORIENTED_EDGE('',*,*,#24766,.F.); -#31690=ORIENTED_EDGE('',*,*,#31689,.T.); -#31691=ORIENTED_EDGE('',*,*,#27764,.T.); -#31692=ORIENTED_EDGE('',*,*,#31676,.F.); -#31693=EDGE_LOOP('',(#31688,#31690,#31691,#31692)); -#31694=FACE_OUTER_BOUND('',#31693,.F.); -#31696=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.351929544180E0)); -#31697=DIRECTION('',(-3.142331229740E-1,0.E0,9.493458507973E-1)); -#31698=DIRECTION('',(9.493458507973E-1,0.E0,3.142331229740E-1)); -#31699=AXIS2_PLACEMENT_3D('',#31696,#31697,#31698); -#31700=PLANE('',#31699); -#31701=ORIENTED_EDGE('',*,*,#24764,.F.); -#31703=ORIENTED_EDGE('',*,*,#31702,.T.); -#31704=ORIENTED_EDGE('',*,*,#27766,.T.); -#31705=ORIENTED_EDGE('',*,*,#31689,.F.); -#31706=EDGE_LOOP('',(#31701,#31703,#31704,#31705)); -#31707=FACE_OUTER_BOUND('',#31706,.F.); -#31709=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.351929544180E0)); -#31710=DIRECTION('',(0.E0,0.E0,1.E0)); -#31711=DIRECTION('',(1.E0,0.E0,0.E0)); -#31712=AXIS2_PLACEMENT_3D('',#31709,#31710,#31711); -#31713=PLANE('',#31712); -#31714=ORIENTED_EDGE('',*,*,#24762,.F.); -#31716=ORIENTED_EDGE('',*,*,#31715,.T.); -#31717=ORIENTED_EDGE('',*,*,#27768,.T.); -#31718=ORIENTED_EDGE('',*,*,#31702,.F.); -#31719=EDGE_LOOP('',(#31714,#31716,#31717,#31718)); -#31720=FACE_OUTER_BOUND('',#31719,.F.); -#31722=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.408269899590E0)); -#31723=DIRECTION('',(4.037599498491E-1,0.E0,9.148649642969E-1)); -#31724=DIRECTION('',(9.148649642969E-1,0.E0,-4.037599498491E-1)); -#31725=AXIS2_PLACEMENT_3D('',#31722,#31723,#31724); -#31726=PLANE('',#31725); -#31727=ORIENTED_EDGE('',*,*,#24760,.F.); -#31729=ORIENTED_EDGE('',*,*,#31728,.T.); -#31730=ORIENTED_EDGE('',*,*,#27770,.T.); -#31731=ORIENTED_EDGE('',*,*,#31715,.F.); -#31732=EDGE_LOOP('',(#31727,#31729,#31730,#31731)); -#31733=FACE_OUTER_BOUND('',#31732,.F.); -#31735=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.492780271514E0)); -#31736=DIRECTION('',(7.046177928501E-1,0.E0,7.095870390580E-1)); -#31737=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#31738=AXIS2_PLACEMENT_3D('',#31735,#31736,#31737); -#31739=PLANE('',#31738); -#31740=ORIENTED_EDGE('',*,*,#24758,.F.); -#31742=ORIENTED_EDGE('',*,*,#31741,.T.); -#31743=ORIENTED_EDGE('',*,*,#27772,.T.); -#31744=ORIENTED_EDGE('',*,*,#31728,.F.); -#31745=EDGE_LOOP('',(#31740,#31742,#31743,#31744)); -#31746=FACE_OUTER_BOUND('',#31745,.F.); -#31748=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.633630676466E0)); -#31749=DIRECTION('',(9.572669363311E-1,0.E0,2.892058308668E-1)); -#31750=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#31751=AXIS2_PLACEMENT_3D('',#31748,#31749,#31750); -#31752=PLANE('',#31751); -#31753=ORIENTED_EDGE('',*,*,#24756,.F.); -#31755=ORIENTED_EDGE('',*,*,#31754,.T.); -#31756=ORIENTED_EDGE('',*,*,#27774,.T.); -#31757=ORIENTED_EDGE('',*,*,#31741,.F.); -#31758=EDGE_LOOP('',(#31753,#31755,#31756,#31757)); -#31759=FACE_OUTER_BOUND('',#31758,.F.); -#31761=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,4.746311387286E0)); -#31762=DIRECTION('',(1.E0,0.E0,0.E0)); -#31763=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31764=AXIS2_PLACEMENT_3D('',#31761,#31762,#31763); -#31765=PLANE('',#31764); -#31766=ORIENTED_EDGE('',*,*,#24754,.F.); -#31768=ORIENTED_EDGE('',*,*,#31767,.T.); -#31769=ORIENTED_EDGE('',*,*,#27776,.T.); -#31770=ORIENTED_EDGE('',*,*,#31754,.F.); -#31771=EDGE_LOOP('',(#31766,#31768,#31769,#31770)); -#31772=FACE_OUTER_BOUND('',#31771,.F.); -#31774=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,4.887161792238E0)); -#31775=DIRECTION('',(9.572669363311E-1,0.E0,-2.892058308668E-1)); -#31776=DIRECTION('',(-2.892058308668E-1,0.E0,-9.572669363311E-1)); -#31777=AXIS2_PLACEMENT_3D('',#31774,#31775,#31776); -#31778=PLANE('',#31777); -#31779=ORIENTED_EDGE('',*,*,#24752,.F.); -#31781=ORIENTED_EDGE('',*,*,#31780,.T.); -#31782=ORIENTED_EDGE('',*,*,#27778,.T.); -#31783=ORIENTED_EDGE('',*,*,#31767,.F.); -#31784=EDGE_LOOP('',(#31779,#31781,#31782,#31783)); -#31785=FACE_OUTER_BOUND('',#31784,.F.); -#31787=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,4.971672164162E0)); -#31788=DIRECTION('',(7.046177928501E-1,0.E0,-7.095870390580E-1)); -#31789=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#31790=AXIS2_PLACEMENT_3D('',#31787,#31788,#31789); -#31791=PLANE('',#31790); -#31792=ORIENTED_EDGE('',*,*,#24750,.F.); -#31794=ORIENTED_EDGE('',*,*,#31793,.T.); -#31795=ORIENTED_EDGE('',*,*,#27780,.T.); -#31796=ORIENTED_EDGE('',*,*,#31780,.F.); -#31797=EDGE_LOOP('',(#31792,#31794,#31795,#31796)); -#31798=FACE_OUTER_BOUND('',#31797,.F.); -#31800=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.028012519572E0)); -#31801=DIRECTION('',(4.037599498491E-1,0.E0,-9.148649642969E-1)); -#31802=DIRECTION('',(-9.148649642969E-1,0.E0,-4.037599498491E-1)); -#31803=AXIS2_PLACEMENT_3D('',#31800,#31801,#31802); -#31804=PLANE('',#31803); -#31805=ORIENTED_EDGE('',*,*,#24748,.F.); -#31807=ORIENTED_EDGE('',*,*,#31806,.T.); -#31808=ORIENTED_EDGE('',*,*,#27782,.T.); -#31809=ORIENTED_EDGE('',*,*,#31793,.F.); -#31810=EDGE_LOOP('',(#31805,#31807,#31808,#31809)); -#31811=FACE_OUTER_BOUND('',#31810,.F.); -#31813=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,5.168863246906E0)); -#31814=DIRECTION('',(1.E0,0.E0,0.E0)); -#31815=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31816=AXIS2_PLACEMENT_3D('',#31813,#31814,#31815); -#31817=PLANE('',#31816); -#31818=ORIENTED_EDGE('',*,*,#24746,.F.); -#31820=ORIENTED_EDGE('',*,*,#31819,.T.); -#31821=ORIENTED_EDGE('',*,*,#27784,.T.); -#31822=ORIENTED_EDGE('',*,*,#31806,.F.); -#31823=EDGE_LOOP('',(#31818,#31820,#31821,#31822)); -#31824=FACE_OUTER_BOUND('',#31823,.F.); -#31826=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,5.140692908010E0)); -#31827=DIRECTION('',(-1.632797103197E-1,0.E0,9.865798174491E-1)); -#31828=DIRECTION('',(9.865798174491E-1,0.E0,1.632797103197E-1)); -#31829=AXIS2_PLACEMENT_3D('',#31826,#31827,#31828); -#31830=PLANE('',#31829); -#31831=ORIENTED_EDGE('',*,*,#24744,.F.); -#31833=ORIENTED_EDGE('',*,*,#31832,.T.); -#31834=ORIENTED_EDGE('',*,*,#27786,.T.); -#31835=ORIENTED_EDGE('',*,*,#31819,.F.); -#31836=EDGE_LOOP('',(#31831,#31833,#31834,#31835)); -#31837=FACE_OUTER_BOUND('',#31836,.F.); -#31839=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,5.028012519572E0)); -#31840=DIRECTION('',(-5.520018080328E-1,0.E0,8.338429132208E-1)); -#31841=DIRECTION('',(8.338429132208E-1,0.E0,5.520018080328E-1)); -#31842=AXIS2_PLACEMENT_3D('',#31839,#31840,#31841); -#31843=PLANE('',#31842); -#31844=ORIENTED_EDGE('',*,*,#24742,.F.); -#31846=ORIENTED_EDGE('',*,*,#31845,.T.); -#31847=ORIENTED_EDGE('',*,*,#27788,.T.); -#31848=ORIENTED_EDGE('',*,*,#31832,.F.); -#31849=EDGE_LOOP('',(#31844,#31846,#31847,#31848)); -#31850=FACE_OUTER_BOUND('',#31849,.F.); -#31852=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.915332131134E0)); -#31853=DIRECTION('',(-7.979692271762E-1,0.E0,6.026981935262E-1)); -#31854=DIRECTION('',(6.026981935262E-1,0.E0,7.979692271762E-1)); -#31855=AXIS2_PLACEMENT_3D('',#31852,#31853,#31854); -#31856=PLANE('',#31855); -#31857=ORIENTED_EDGE('',*,*,#24740,.F.); -#31859=ORIENTED_EDGE('',*,*,#31858,.T.); -#31860=ORIENTED_EDGE('',*,*,#27790,.T.); -#31861=ORIENTED_EDGE('',*,*,#31845,.F.); -#31862=EDGE_LOOP('',(#31857,#31859,#31860,#31861)); -#31863=FACE_OUTER_BOUND('',#31862,.F.); -#31865=CARTESIAN_POINT('',(0.E0,1.55E0,4.718141048390E0)); -#31866=DIRECTION('',(-9.774987906878E-1,0.E0,2.109410206761E-1)); -#31867=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#31868=AXIS2_PLACEMENT_3D('',#31865,#31866,#31867); -#31869=PLANE('',#31868); -#31870=ORIENTED_EDGE('',*,*,#24738,.F.); -#31872=ORIENTED_EDGE('',*,*,#31871,.T.); -#31873=ORIENTED_EDGE('',*,*,#27792,.T.); -#31874=ORIENTED_EDGE('',*,*,#31858,.F.); -#31875=EDGE_LOOP('',(#31870,#31872,#31873,#31874)); -#31876=FACE_OUTER_BOUND('',#31875,.F.); -#31878=CARTESIAN_POINT('',(0.E0,1.55E0,4.661801015362E0)); -#31879=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31880=DIRECTION('',(0.E0,0.E0,1.E0)); -#31881=AXIS2_PLACEMENT_3D('',#31878,#31879,#31880); -#31882=PLANE('',#31881); -#31883=ORIENTED_EDGE('',*,*,#24736,.F.); -#31885=ORIENTED_EDGE('',*,*,#31884,.T.); -#31886=ORIENTED_EDGE('',*,*,#27794,.T.); -#31887=ORIENTED_EDGE('',*,*,#31871,.F.); -#31888=EDGE_LOOP('',(#31883,#31885,#31886,#31887)); -#31889=FACE_OUTER_BOUND('',#31888,.F.); -#31891=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,4.464609932618E0)); -#31892=DIRECTION('',(-9.774987906878E-1,0.E0,-2.109410206761E-1)); -#31893=DIRECTION('',(-2.109410206761E-1,0.E0,9.774987906878E-1)); -#31894=AXIS2_PLACEMENT_3D('',#31891,#31892,#31893); -#31895=PLANE('',#31894); -#31896=ORIENTED_EDGE('',*,*,#24734,.F.); -#31898=ORIENTED_EDGE('',*,*,#31897,.T.); -#31899=ORIENTED_EDGE('',*,*,#27796,.T.); -#31900=ORIENTED_EDGE('',*,*,#31884,.F.); -#31901=EDGE_LOOP('',(#31896,#31898,#31899,#31900)); -#31902=FACE_OUTER_BOUND('',#31901,.F.); -#31904=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,4.351929544180E0)); -#31905=DIRECTION('',(-7.979692271762E-1,0.E0,-6.026981935262E-1)); -#31906=DIRECTION('',(-6.026981935262E-1,0.E0,7.979692271762E-1)); -#31907=AXIS2_PLACEMENT_3D('',#31904,#31905,#31906); -#31908=PLANE('',#31907); -#31909=ORIENTED_EDGE('',*,*,#24732,.F.); -#31911=ORIENTED_EDGE('',*,*,#31910,.T.); -#31912=ORIENTED_EDGE('',*,*,#27798,.T.); -#31913=ORIENTED_EDGE('',*,*,#31897,.F.); -#31914=EDGE_LOOP('',(#31909,#31911,#31912,#31913)); -#31915=FACE_OUTER_BOUND('',#31914,.F.); -#31917=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,4.239249155742E0)); -#31918=DIRECTION('',(-5.520018080328E-1,0.E0,-8.338429132208E-1)); -#31919=DIRECTION('',(-8.338429132208E-1,0.E0,5.520018080328E-1)); -#31920=AXIS2_PLACEMENT_3D('',#31917,#31918,#31919); -#31921=PLANE('',#31920); -#31922=ORIENTED_EDGE('',*,*,#24730,.F.); -#31924=ORIENTED_EDGE('',*,*,#31923,.T.); -#31925=ORIENTED_EDGE('',*,*,#27800,.T.); -#31926=ORIENTED_EDGE('',*,*,#31910,.F.); -#31927=EDGE_LOOP('',(#31922,#31924,#31925,#31926)); -#31928=FACE_OUTER_BOUND('',#31927,.F.); -#31930=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,4.211078816846E0)); -#31931=DIRECTION('',(-1.632797103197E-1,0.E0,-9.865798174491E-1)); -#31932=DIRECTION('',(-9.865798174491E-1,0.E0,1.632797103197E-1)); -#31933=AXIS2_PLACEMENT_3D('',#31930,#31931,#31932); -#31934=PLANE('',#31933); -#31935=ORIENTED_EDGE('',*,*,#24728,.F.); -#31937=ORIENTED_EDGE('',*,*,#31936,.T.); -#31938=ORIENTED_EDGE('',*,*,#27802,.T.); -#31939=ORIENTED_EDGE('',*,*,#31923,.F.); -#31940=EDGE_LOOP('',(#31935,#31937,#31938,#31939)); -#31941=FACE_OUTER_BOUND('',#31940,.F.); -#31943=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,4.211078816846E0)); -#31944=DIRECTION('',(0.E0,0.E0,-1.E0)); -#31945=DIRECTION('',(-1.E0,0.E0,0.E0)); -#31946=AXIS2_PLACEMENT_3D('',#31943,#31944,#31945); -#31947=PLANE('',#31946); -#31948=ORIENTED_EDGE('',*,*,#24726,.F.); -#31950=ORIENTED_EDGE('',*,*,#31949,.T.); -#31951=ORIENTED_EDGE('',*,*,#27804,.T.); -#31952=ORIENTED_EDGE('',*,*,#31936,.F.); -#31953=EDGE_LOOP('',(#31948,#31950,#31951,#31952)); -#31954=FACE_OUTER_BOUND('',#31953,.F.); -#31956=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,4.239249155742E0)); -#31957=DIRECTION('',(1.632797103197E-1,0.E0,-9.865798174491E-1)); -#31958=DIRECTION('',(-9.865798174491E-1,0.E0,-1.632797103197E-1)); -#31959=AXIS2_PLACEMENT_3D('',#31956,#31957,#31958); -#31960=PLANE('',#31959); -#31961=ORIENTED_EDGE('',*,*,#24724,.F.); -#31963=ORIENTED_EDGE('',*,*,#31962,.T.); -#31964=ORIENTED_EDGE('',*,*,#27806,.T.); -#31965=ORIENTED_EDGE('',*,*,#31949,.F.); -#31966=EDGE_LOOP('',(#31961,#31963,#31964,#31965)); -#31967=FACE_OUTER_BOUND('',#31966,.F.); -#31969=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,4.295589188770E0)); -#31970=DIRECTION('',(4.037580161524E-1,0.E0,-9.148658176982E-1)); -#31971=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#31972=AXIS2_PLACEMENT_3D('',#31969,#31970,#31971); -#31973=PLANE('',#31972); -#31974=ORIENTED_EDGE('',*,*,#24722,.F.); -#31976=ORIENTED_EDGE('',*,*,#31975,.T.); -#31977=ORIENTED_EDGE('',*,*,#27808,.T.); -#31978=ORIENTED_EDGE('',*,*,#31962,.F.); -#31979=EDGE_LOOP('',(#31974,#31976,#31977,#31978)); -#31980=FACE_OUTER_BOUND('',#31979,.F.); -#31982=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,4.408269899590E0)); -#31983=DIRECTION('',(6.617534547244E-1,0.E0,-7.497215250747E-1)); -#31984=DIRECTION('',(-7.497215250747E-1,0.E0,-6.617534547244E-1)); -#31985=AXIS2_PLACEMENT_3D('',#31982,#31983,#31984); -#31986=PLANE('',#31985); -#31987=ORIENTED_EDGE('',*,*,#24720,.F.); -#31989=ORIENTED_EDGE('',*,*,#31988,.T.); -#31990=ORIENTED_EDGE('',*,*,#27810,.T.); -#31991=ORIENTED_EDGE('',*,*,#31975,.F.); -#31992=EDGE_LOOP('',(#31987,#31989,#31990,#31991)); -#31993=FACE_OUTER_BOUND('',#31992,.F.); -#31995=CARTESIAN_POINT('',(1.063829779625E0,1.55E0,4.267419172256E0)); -#31996=DIRECTION('',(-8.558911780584E-1,0.E0,-5.171559642137E-1)); -#31997=DIRECTION('',(-5.171559642137E-1,0.E0,8.558911780584E-1)); -#31998=AXIS2_PLACEMENT_3D('',#31995,#31996,#31997); -#31999=PLANE('',#31998); -#32000=ORIENTED_EDGE('',*,*,#24718,.F.); -#32002=ORIENTED_EDGE('',*,*,#32001,.T.); -#32003=ORIENTED_EDGE('',*,*,#27812,.T.); -#32004=ORIENTED_EDGE('',*,*,#31988,.F.); -#32005=EDGE_LOOP('',(#32000,#32002,#32003,#32004)); -#32006=FACE_OUTER_BOUND('',#32005,.F.); -#32008=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,4.211078816846E0)); -#32009=DIRECTION('',(-4.037599498491E-1,0.E0,-9.148649642969E-1)); -#32010=DIRECTION('',(-9.148649642969E-1,0.E0,4.037599498491E-1)); -#32011=AXIS2_PLACEMENT_3D('',#32008,#32009,#32010); -#32012=PLANE('',#32011); -#32013=ORIENTED_EDGE('',*,*,#24716,.F.); -#32015=ORIENTED_EDGE('',*,*,#32014,.T.); -#32016=ORIENTED_EDGE('',*,*,#27814,.T.); -#32017=ORIENTED_EDGE('',*,*,#32001,.F.); -#32018=EDGE_LOOP('',(#32013,#32015,#32016,#32017)); -#32019=FACE_OUTER_BOUND('',#32018,.F.); -#32021=CARTESIAN_POINT('',(1.361702144146E0,1.55E0,4.182908800332E0)); -#32022=DIRECTION('',(-1.632778359099E-1,0.E0,-9.865801276635E-1)); -#32023=DIRECTION('',(-9.865801276635E-1,0.E0,1.632778359099E-1)); -#32024=AXIS2_PLACEMENT_3D('',#32021,#32022,#32023); -#32025=PLANE('',#32024); -#32026=ORIENTED_EDGE('',*,*,#24714,.F.); -#32028=ORIENTED_EDGE('',*,*,#32027,.T.); -#32029=ORIENTED_EDGE('',*,*,#27816,.T.); -#32030=ORIENTED_EDGE('',*,*,#32014,.F.); -#32031=EDGE_LOOP('',(#32026,#32028,#32029,#32030)); -#32032=FACE_OUTER_BOUND('',#32031,.F.); -#32034=CARTESIAN_POINT('',(1.531914889812E0,1.55E0,4.182908800332E0)); -#32035=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32036=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32037=AXIS2_PLACEMENT_3D('',#32034,#32035,#32036); -#32038=PLANE('',#32037); -#32039=ORIENTED_EDGE('',*,*,#24712,.F.); -#32041=ORIENTED_EDGE('',*,*,#32040,.T.); -#32042=ORIENTED_EDGE('',*,*,#27818,.T.); -#32043=ORIENTED_EDGE('',*,*,#32027,.F.); -#32044=EDGE_LOOP('',(#32039,#32041,#32042,#32043)); -#32045=FACE_OUTER_BOUND('',#32044,.F.); -#32047=CARTESIAN_POINT('',(1.659574478865E0,1.55E0,4.211078816846E0)); -#32048=DIRECTION('',(2.154812353607E-1,0.E0,-9.765079811284E-1)); -#32049=DIRECTION('',(-9.765079811284E-1,0.E0,-2.154812353607E-1)); -#32050=AXIS2_PLACEMENT_3D('',#32047,#32048,#32049); -#32051=PLANE('',#32050); -#32052=ORIENTED_EDGE('',*,*,#24710,.F.); -#32053=ORIENTED_EDGE('',*,*,#31327,.T.); -#32054=ORIENTED_EDGE('',*,*,#27820,.T.); -#32055=ORIENTED_EDGE('',*,*,#32040,.F.); -#32056=EDGE_LOOP('',(#32052,#32053,#32054,#32055)); -#32057=FACE_OUTER_BOUND('',#32056,.F.); -#32059=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.957547701074E0)); -#32060=DIRECTION('',(0.E0,0.E0,1.E0)); -#32061=DIRECTION('',(1.E0,0.E0,0.E0)); -#32062=AXIS2_PLACEMENT_3D('',#32059,#32060,#32061); -#32063=PLANE('',#32062); -#32064=ORIENTED_EDGE('',*,*,#24824,.F.); -#32066=ORIENTED_EDGE('',*,*,#32065,.T.); -#32067=ORIENTED_EDGE('',*,*,#27837,.T.); -#32069=ORIENTED_EDGE('',*,*,#32068,.F.); -#32070=EDGE_LOOP('',(#32064,#32066,#32067,#32069)); -#32071=FACE_OUTER_BOUND('',#32070,.F.); -#32073=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,3.168784337244E0)); -#32074=DIRECTION('',(-5.955889362677E-1,0.E0,8.032893743823E-1)); -#32075=DIRECTION('',(8.032893743823E-1,0.E0,5.955889362677E-1)); -#32076=AXIS2_PLACEMENT_3D('',#32073,#32074,#32075); -#32077=PLANE('',#32076); -#32078=ORIENTED_EDGE('',*,*,#24878,.F.); -#32080=ORIENTED_EDGE('',*,*,#32079,.T.); -#32081=ORIENTED_EDGE('',*,*,#27839,.T.); -#32082=ORIENTED_EDGE('',*,*,#32065,.F.); -#32083=EDGE_LOOP('',(#32078,#32080,#32081,#32082)); -#32084=FACE_OUTER_BOUND('',#32083,.F.); -#32086=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,3.112444304216E0)); -#32087=DIRECTION('',(-3.142315024639E-1,0.E0,9.493463871840E-1)); -#32088=DIRECTION('',(9.493463871840E-1,0.E0,3.142315024639E-1)); -#32089=AXIS2_PLACEMENT_3D('',#32086,#32087,#32088); -#32090=PLANE('',#32089); -#32091=ORIENTED_EDGE('',*,*,#24876,.F.); -#32093=ORIENTED_EDGE('',*,*,#32092,.T.); -#32094=ORIENTED_EDGE('',*,*,#27841,.T.); -#32095=ORIENTED_EDGE('',*,*,#32079,.F.); -#32096=EDGE_LOOP('',(#32091,#32093,#32094,#32095)); -#32097=FACE_OUTER_BOUND('',#32096,.F.); -#32099=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.112444304216E0)); -#32100=DIRECTION('',(0.E0,0.E0,1.E0)); -#32101=DIRECTION('',(1.E0,0.E0,0.E0)); -#32102=AXIS2_PLACEMENT_3D('',#32099,#32100,#32101); -#32103=PLANE('',#32102); -#32104=ORIENTED_EDGE('',*,*,#24874,.F.); -#32106=ORIENTED_EDGE('',*,*,#32105,.T.); -#32107=ORIENTED_EDGE('',*,*,#27843,.T.); -#32108=ORIENTED_EDGE('',*,*,#32092,.F.); -#32109=EDGE_LOOP('',(#32104,#32106,#32107,#32108)); -#32110=FACE_OUTER_BOUND('',#32109,.F.); -#32112=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.168784337244E0)); -#32113=DIRECTION('',(4.037580161524E-1,0.E0,9.148658176982E-1)); -#32114=DIRECTION('',(9.148658176982E-1,0.E0,-4.037580161524E-1)); -#32115=AXIS2_PLACEMENT_3D('',#32112,#32113,#32114); -#32116=PLANE('',#32115); -#32117=ORIENTED_EDGE('',*,*,#24872,.F.); -#32119=ORIENTED_EDGE('',*,*,#32118,.T.); -#32120=ORIENTED_EDGE('',*,*,#27845,.T.); -#32121=ORIENTED_EDGE('',*,*,#32105,.F.); -#32122=EDGE_LOOP('',(#32117,#32119,#32120,#32121)); -#32123=FACE_OUTER_BOUND('',#32122,.F.); -#32125=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.253294709168E0)); -#32126=DIRECTION('',(7.046177928501E-1,0.E0,7.095870390580E-1)); -#32127=DIRECTION('',(7.095870390580E-1,0.E0,-7.046177928501E-1)); -#32128=AXIS2_PLACEMENT_3D('',#32125,#32126,#32127); -#32129=PLANE('',#32128); -#32130=ORIENTED_EDGE('',*,*,#24870,.F.); -#32132=ORIENTED_EDGE('',*,*,#32131,.T.); -#32133=ORIENTED_EDGE('',*,*,#27847,.T.); -#32134=ORIENTED_EDGE('',*,*,#32118,.F.); -#32135=EDGE_LOOP('',(#32130,#32132,#32133,#32134)); -#32136=FACE_OUTER_BOUND('',#32135,.F.); -#32138=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.394145114120E0)); -#32139=DIRECTION('',(9.572669363311E-1,0.E0,2.892058308668E-1)); -#32140=DIRECTION('',(2.892058308668E-1,0.E0,-9.572669363311E-1)); -#32141=AXIS2_PLACEMENT_3D('',#32138,#32139,#32140); -#32142=PLANE('',#32141); -#32143=ORIENTED_EDGE('',*,*,#24868,.F.); -#32145=ORIENTED_EDGE('',*,*,#32144,.T.); -#32146=ORIENTED_EDGE('',*,*,#27849,.T.); -#32147=ORIENTED_EDGE('',*,*,#32131,.F.); -#32148=EDGE_LOOP('',(#32143,#32145,#32146,#32147)); -#32149=FACE_OUTER_BOUND('',#32148,.F.); -#32151=CARTESIAN_POINT('',(2.127659320831E-1,1.55E0,3.506825824940E0)); -#32152=DIRECTION('',(1.E0,0.E0,0.E0)); -#32153=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32154=AXIS2_PLACEMENT_3D('',#32151,#32152,#32153); -#32155=PLANE('',#32154); -#32156=ORIENTED_EDGE('',*,*,#24866,.F.); -#32158=ORIENTED_EDGE('',*,*,#32157,.T.); -#32159=ORIENTED_EDGE('',*,*,#27851,.T.); -#32160=ORIENTED_EDGE('',*,*,#32144,.F.); -#32161=EDGE_LOOP('',(#32156,#32158,#32159,#32160)); -#32162=FACE_OUTER_BOUND('',#32161,.F.); -#32164=CARTESIAN_POINT('',(2.553191184998E-1,1.55E0,3.647676552274E0)); -#32165=DIRECTION('',(9.572671195869E-1,0.E0,-2.892052242921E-1)); -#32166=DIRECTION('',(-2.892052242921E-1,0.E0,-9.572671195869E-1)); -#32167=AXIS2_PLACEMENT_3D('',#32164,#32165,#32166); -#32168=PLANE('',#32167); -#32169=ORIENTED_EDGE('',*,*,#24864,.F.); -#32171=ORIENTED_EDGE('',*,*,#32170,.T.); -#32172=ORIENTED_EDGE('',*,*,#27853,.T.); -#32173=ORIENTED_EDGE('',*,*,#32157,.F.); -#32174=EDGE_LOOP('',(#32169,#32171,#32172,#32173)); -#32175=FACE_OUTER_BOUND('',#32174,.F.); -#32177=CARTESIAN_POINT('',(3.404254913330E-1,1.55E0,3.732186924198E0)); -#32178=DIRECTION('',(7.046177928501E-1,0.E0,-7.095870390580E-1)); -#32179=DIRECTION('',(-7.095870390580E-1,0.E0,-7.046177928501E-1)); -#32180=AXIS2_PLACEMENT_3D('',#32177,#32178,#32179); -#32181=PLANE('',#32180); -#32182=ORIENTED_EDGE('',*,*,#24862,.F.); -#32184=ORIENTED_EDGE('',*,*,#32183,.T.); -#32185=ORIENTED_EDGE('',*,*,#27855,.T.); -#32186=ORIENTED_EDGE('',*,*,#32170,.F.); -#32187=EDGE_LOOP('',(#32182,#32184,#32185,#32186)); -#32188=FACE_OUTER_BOUND('',#32187,.F.); -#32190=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.788526957226E0)); -#32191=DIRECTION('',(4.037580161524E-1,0.E0,-9.148658176982E-1)); -#32192=DIRECTION('',(-9.148658176982E-1,0.E0,-4.037580161524E-1)); -#32193=AXIS2_PLACEMENT_3D('',#32190,#32191,#32192); -#32194=PLANE('',#32193); -#32195=ORIENTED_EDGE('',*,*,#24860,.F.); -#32197=ORIENTED_EDGE('',*,*,#32196,.T.); -#32198=ORIENTED_EDGE('',*,*,#27857,.T.); -#32199=ORIENTED_EDGE('',*,*,#32183,.F.); -#32200=EDGE_LOOP('',(#32195,#32197,#32198,#32199)); -#32201=FACE_OUTER_BOUND('',#32200,.F.); -#32203=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,3.929377684560E0)); -#32204=DIRECTION('',(1.E0,0.E0,0.E0)); -#32205=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32206=AXIS2_PLACEMENT_3D('',#32203,#32204,#32205); -#32207=PLANE('',#32206); -#32208=ORIENTED_EDGE('',*,*,#24858,.F.); -#32210=ORIENTED_EDGE('',*,*,#32209,.T.); -#32211=ORIENTED_EDGE('',*,*,#27859,.T.); -#32212=ORIENTED_EDGE('',*,*,#32196,.F.); -#32213=EDGE_LOOP('',(#32208,#32210,#32211,#32212)); -#32214=FACE_OUTER_BOUND('',#32213,.F.); -#32216=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,3.901207668046E0)); -#32217=DIRECTION('',(-1.632778915618E-1,0.E0,9.865801184532E-1)); -#32218=DIRECTION('',(9.865801184532E-1,0.E0,1.632778915618E-1)); -#32219=AXIS2_PLACEMENT_3D('',#32216,#32217,#32218); -#32220=PLANE('',#32219); -#32221=ORIENTED_EDGE('',*,*,#24856,.F.); -#32223=ORIENTED_EDGE('',*,*,#32222,.T.); -#32224=ORIENTED_EDGE('',*,*,#27861,.T.); -#32225=ORIENTED_EDGE('',*,*,#32209,.F.); -#32226=EDGE_LOOP('',(#32221,#32223,#32224,#32225)); -#32227=FACE_OUTER_BOUND('',#32226,.F.); -#32229=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.788526957226E0)); -#32230=DIRECTION('',(-5.520029061031E-1,0.E0,8.338421863001E-1)); -#32231=DIRECTION('',(8.338421863001E-1,0.E0,5.520029061031E-1)); -#32232=AXIS2_PLACEMENT_3D('',#32229,#32230,#32231); -#32233=PLANE('',#32232); -#32234=ORIENTED_EDGE('',*,*,#24854,.F.); -#32236=ORIENTED_EDGE('',*,*,#32235,.T.); -#32237=ORIENTED_EDGE('',*,*,#27863,.T.); -#32238=ORIENTED_EDGE('',*,*,#32222,.F.); -#32239=EDGE_LOOP('',(#32234,#32236,#32237,#32238)); -#32240=FACE_OUTER_BOUND('',#32239,.F.); -#32242=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.675846568788E0)); -#32243=DIRECTION('',(-7.979692271762E-1,0.E0,6.026981935263E-1)); -#32244=DIRECTION('',(6.026981935263E-1,0.E0,7.979692271762E-1)); -#32245=AXIS2_PLACEMENT_3D('',#32242,#32243,#32244); -#32246=PLANE('',#32245); -#32247=ORIENTED_EDGE('',*,*,#24852,.F.); -#32249=ORIENTED_EDGE('',*,*,#32248,.T.); -#32250=ORIENTED_EDGE('',*,*,#27865,.T.); -#32251=ORIENTED_EDGE('',*,*,#32235,.F.); -#32252=EDGE_LOOP('',(#32247,#32249,#32250,#32251)); -#32253=FACE_OUTER_BOUND('',#32252,.F.); -#32255=CARTESIAN_POINT('',(0.E0,1.55E0,3.478655486044E0)); -#32256=DIRECTION('',(-9.774987906878E-1,0.E0,2.109410206761E-1)); -#32257=DIRECTION('',(2.109410206761E-1,0.E0,9.774987906878E-1)); -#32258=AXIS2_PLACEMENT_3D('',#32255,#32256,#32257); -#32259=PLANE('',#32258); -#32260=ORIENTED_EDGE('',*,*,#24850,.F.); -#32262=ORIENTED_EDGE('',*,*,#32261,.T.); -#32263=ORIENTED_EDGE('',*,*,#27867,.T.); -#32264=ORIENTED_EDGE('',*,*,#32248,.F.); -#32265=EDGE_LOOP('',(#32260,#32262,#32263,#32264)); -#32266=FACE_OUTER_BOUND('',#32265,.F.); -#32268=CARTESIAN_POINT('',(0.E0,1.55E0,3.365975419988E0)); -#32269=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32270=DIRECTION('',(0.E0,0.E0,1.E0)); -#32271=AXIS2_PLACEMENT_3D('',#32268,#32269,#32270); -#32272=PLANE('',#32271); -#32273=ORIENTED_EDGE('',*,*,#24848,.F.); -#32275=ORIENTED_EDGE('',*,*,#32274,.T.); -#32276=ORIENTED_EDGE('',*,*,#27869,.T.); -#32277=ORIENTED_EDGE('',*,*,#32261,.F.); -#32278=EDGE_LOOP('',(#32273,#32275,#32276,#32277)); -#32279=FACE_OUTER_BOUND('',#32278,.F.); -#32281=CARTESIAN_POINT('',(4.255318641663E-2,1.55E0,3.196954676140E0)); -#32282=DIRECTION('',(-9.697388722849E-1,0.E0,-2.441444645688E-1)); -#32283=DIRECTION('',(-2.441444645688E-1,0.E0,9.697388722849E-1)); -#32284=AXIS2_PLACEMENT_3D('',#32281,#32282,#32283); -#32285=PLANE('',#32284); -#32286=ORIENTED_EDGE('',*,*,#24846,.F.); -#32288=ORIENTED_EDGE('',*,*,#32287,.T.); -#32289=ORIENTED_EDGE('',*,*,#27871,.T.); -#32290=ORIENTED_EDGE('',*,*,#32274,.F.); -#32291=EDGE_LOOP('',(#32286,#32288,#32289,#32290)); -#32292=FACE_OUTER_BOUND('',#32291,.F.); -#32294=CARTESIAN_POINT('',(1.276595592499E-1,1.55E0,3.084273965320E0)); -#32295=DIRECTION('',(-7.979700564663E-1,0.E0,-6.026970955489E-1)); -#32296=DIRECTION('',(-6.026970955489E-1,0.E0,7.979700564663E-1)); -#32297=AXIS2_PLACEMENT_3D('',#32294,#32295,#32296); -#32298=PLANE('',#32297); -#32299=ORIENTED_EDGE('',*,*,#24844,.F.); -#32301=ORIENTED_EDGE('',*,*,#32300,.T.); -#32302=ORIENTED_EDGE('',*,*,#27873,.T.); -#32303=ORIENTED_EDGE('',*,*,#32287,.F.); -#32304=EDGE_LOOP('',(#32299,#32301,#32302,#32303)); -#32305=FACE_OUTER_BOUND('',#32304,.F.); -#32307=CARTESIAN_POINT('',(2.978723049164E-1,1.55E0,2.971593254501E0)); -#32308=DIRECTION('',(-5.520029061031E-1,0.E0,-8.338421863001E-1)); -#32309=DIRECTION('',(-8.338421863001E-1,0.E0,5.520029061031E-1)); -#32310=AXIS2_PLACEMENT_3D('',#32307,#32308,#32309); -#32311=PLANE('',#32310); -#32312=ORIENTED_EDGE('',*,*,#24842,.F.); -#32314=ORIENTED_EDGE('',*,*,#32313,.T.); -#32315=ORIENTED_EDGE('',*,*,#27875,.T.); -#32316=ORIENTED_EDGE('',*,*,#32300,.F.); -#32317=EDGE_LOOP('',(#32312,#32314,#32315,#32316)); -#32318=FACE_OUTER_BOUND('',#32317,.F.); -#32320=CARTESIAN_POINT('',(4.680850505829E-1,1.55E0,2.943423560368E0)); -#32321=DIRECTION('',(-1.632760728023E-1,0.E0,-9.865804194541E-1)); -#32322=DIRECTION('',(-9.865804194541E-1,0.E0,1.632760728023E-1)); -#32323=AXIS2_PLACEMENT_3D('',#32320,#32321,#32322); -#32324=PLANE('',#32323); -#32325=ORIENTED_EDGE('',*,*,#24840,.F.); -#32327=ORIENTED_EDGE('',*,*,#32326,.T.); -#32328=ORIENTED_EDGE('',*,*,#27877,.T.); -#32329=ORIENTED_EDGE('',*,*,#32313,.F.); -#32330=EDGE_LOOP('',(#32325,#32327,#32328,#32329)); -#32331=FACE_OUTER_BOUND('',#32330,.F.); -#32333=CARTESIAN_POINT('',(5.531915426254E-1,1.55E0,2.943423560368E0)); -#32334=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32335=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32336=AXIS2_PLACEMENT_3D('',#32333,#32334,#32335); -#32337=PLANE('',#32336); -#32338=ORIENTED_EDGE('',*,*,#24838,.F.); -#32340=ORIENTED_EDGE('',*,*,#32339,.T.); -#32341=ORIENTED_EDGE('',*,*,#27879,.T.); -#32342=ORIENTED_EDGE('',*,*,#32326,.F.); -#32343=EDGE_LOOP('',(#32338,#32340,#32341,#32342)); -#32344=FACE_OUTER_BOUND('',#32343,.F.); -#32346=CARTESIAN_POINT('',(7.234042882919E-1,1.55E0,2.971593254501E0)); -#32347=DIRECTION('',(1.632760728023E-1,0.E0,-9.865804194541E-1)); -#32348=DIRECTION('',(-9.865804194541E-1,0.E0,-1.632760728023E-1)); -#32349=AXIS2_PLACEMENT_3D('',#32346,#32347,#32348); -#32350=PLANE('',#32349); -#32351=ORIENTED_EDGE('',*,*,#24836,.F.); -#32353=ORIENTED_EDGE('',*,*,#32352,.T.); -#32354=ORIENTED_EDGE('',*,*,#27881,.T.); -#32355=ORIENTED_EDGE('',*,*,#32339,.F.); -#32356=EDGE_LOOP('',(#32351,#32353,#32354,#32355)); -#32357=FACE_OUTER_BOUND('',#32356,.F.); -#32359=CARTESIAN_POINT('',(8.510638475418E-1,1.55E0,3.027933932292E0)); -#32360=DIRECTION('',(4.037618835403E-1,0.E0,-9.148641108930E-1)); -#32361=DIRECTION('',(-9.148641108930E-1,0.E0,-4.037618835403E-1)); -#32362=AXIS2_PLACEMENT_3D('',#32359,#32360,#32361); -#32363=PLANE('',#32362); -#32364=ORIENTED_EDGE('',*,*,#24834,.F.); -#32366=ORIENTED_EDGE('',*,*,#32365,.T.); -#32367=ORIENTED_EDGE('',*,*,#27883,.T.); -#32368=ORIENTED_EDGE('',*,*,#32352,.F.); -#32369=EDGE_LOOP('',(#32364,#32366,#32367,#32368)); -#32370=FACE_OUTER_BOUND('',#32369,.F.); -#32372=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,3.732186924198E0)); -#32373=DIRECTION('',(6.011604742403E-1,0.E0,-7.991283277492E-1)); -#32374=DIRECTION('',(-7.991283277492E-1,0.E0,-6.011604742403E-1)); -#32375=AXIS2_PLACEMENT_3D('',#32372,#32373,#32374); -#32376=PLANE('',#32375); -#32377=ORIENTED_EDGE('',*,*,#24832,.F.); -#32379=ORIENTED_EDGE('',*,*,#32378,.T.); -#32380=ORIENTED_EDGE('',*,*,#27885,.T.); -#32381=ORIENTED_EDGE('',*,*,#32365,.F.); -#32382=EDGE_LOOP('',(#32377,#32379,#32380,#32381)); -#32383=FACE_OUTER_BOUND('',#32382,.F.); -#32385=CARTESIAN_POINT('',(1.787234038115E0,1.55E0,2.943423560368E0)); -#32386=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32387=DIRECTION('',(0.E0,0.E0,1.E0)); -#32388=AXIS2_PLACEMENT_3D('',#32385,#32386,#32387); -#32389=PLANE('',#32388); -#32390=ORIENTED_EDGE('',*,*,#24830,.F.); -#32392=ORIENTED_EDGE('',*,*,#32391,.T.); -#32393=ORIENTED_EDGE('',*,*,#27887,.T.); -#32394=ORIENTED_EDGE('',*,*,#32378,.F.); -#32395=EDGE_LOOP('',(#32390,#32392,#32393,#32394)); -#32396=FACE_OUTER_BOUND('',#32395,.F.); -#32398=CARTESIAN_POINT('',(2.E0,1.55E0,2.943423560368E0)); -#32399=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32400=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32401=AXIS2_PLACEMENT_3D('',#32398,#32399,#32400); -#32402=PLANE('',#32401); -#32403=ORIENTED_EDGE('',*,*,#24828,.F.); -#32405=ORIENTED_EDGE('',*,*,#32404,.T.); -#32406=ORIENTED_EDGE('',*,*,#27889,.T.); -#32407=ORIENTED_EDGE('',*,*,#32391,.F.); -#32408=EDGE_LOOP('',(#32403,#32405,#32406,#32407)); -#32409=FACE_OUTER_BOUND('',#32408,.F.); -#32411=CARTESIAN_POINT('',(2.E0,1.55E0,3.957547701074E0)); -#32412=DIRECTION('',(1.E0,0.E0,0.E0)); -#32413=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32414=AXIS2_PLACEMENT_3D('',#32411,#32412,#32413); -#32415=PLANE('',#32414); -#32416=ORIENTED_EDGE('',*,*,#24826,.F.); -#32417=ORIENTED_EDGE('',*,*,#32068,.T.); -#32418=ORIENTED_EDGE('',*,*,#27891,.T.); -#32419=ORIENTED_EDGE('',*,*,#32404,.F.); -#32420=EDGE_LOOP('',(#32416,#32417,#32418,#32419)); -#32421=FACE_OUTER_BOUND('',#32420,.F.); -#32423=CARTESIAN_POINT('',(2.E0,1.55E0,1.760278353432E0)); -#32424=DIRECTION('',(1.E0,0.E0,0.E0)); -#32425=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32426=AXIS2_PLACEMENT_3D('',#32423,#32424,#32425); -#32427=PLANE('',#32426); -#32428=ORIENTED_EDGE('',*,*,#24882,.F.); -#32430=ORIENTED_EDGE('',*,*,#32429,.T.); -#32431=ORIENTED_EDGE('',*,*,#27908,.T.); -#32433=ORIENTED_EDGE('',*,*,#32432,.F.); -#32434=EDGE_LOOP('',(#32428,#32430,#32431,#32433)); -#32435=FACE_OUTER_BOUND('',#32434,.F.); -#32437=CARTESIAN_POINT('',(1.191489338875E0,1.55E0,2.154659874156E0)); -#32438=DIRECTION('',(4.384111289239E-1,0.E0,8.987745446082E-1)); -#32439=DIRECTION('',(8.987745446082E-1,0.E0,-4.384111289239E-1)); -#32440=AXIS2_PLACEMENT_3D('',#32437,#32438,#32439); -#32441=PLANE('',#32440); -#32442=ORIENTED_EDGE('',*,*,#24904,.F.); -#32444=ORIENTED_EDGE('',*,*,#32443,.T.); -#32445=ORIENTED_EDGE('',*,*,#27910,.T.); -#32446=ORIENTED_EDGE('',*,*,#32429,.F.); -#32447=EDGE_LOOP('',(#32442,#32444,#32445,#32446)); -#32448=FACE_OUTER_BOUND('',#32447,.F.); -#32450=CARTESIAN_POINT('',(2.E0,1.55E0,2.549041394881E0)); -#32451=DIRECTION('',(4.384111289239E-1,0.E0,-8.987745446082E-1)); -#32452=DIRECTION('',(-8.987745446082E-1,0.E0,-4.384111289239E-1)); -#32453=AXIS2_PLACEMENT_3D('',#32450,#32451,#32452); -#32454=PLANE('',#32453); -#32455=ORIENTED_EDGE('',*,*,#24902,.F.); -#32457=ORIENTED_EDGE('',*,*,#32456,.T.); -#32458=ORIENTED_EDGE('',*,*,#27912,.T.); -#32459=ORIENTED_EDGE('',*,*,#32443,.F.); -#32460=EDGE_LOOP('',(#32455,#32457,#32458,#32459)); -#32461=FACE_OUTER_BOUND('',#32460,.F.); -#32463=CARTESIAN_POINT('',(2.E0,1.55E0,2.718062138729E0)); -#32464=DIRECTION('',(1.E0,0.E0,0.E0)); -#32465=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32466=AXIS2_PLACEMENT_3D('',#32463,#32464,#32465); -#32467=PLANE('',#32466); -#32468=ORIENTED_EDGE('',*,*,#24900,.F.); -#32470=ORIENTED_EDGE('',*,*,#32469,.T.); -#32471=ORIENTED_EDGE('',*,*,#27914,.T.); -#32472=ORIENTED_EDGE('',*,*,#32456,.F.); -#32473=EDGE_LOOP('',(#32468,#32470,#32471,#32472)); -#32474=FACE_OUTER_BOUND('',#32473,.F.); -#32476=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.239170246080E0)); -#32477=DIRECTION('',(-4.245563363410E-1,0.E0,9.054015226808E-1)); -#32478=DIRECTION('',(9.054015226808E-1,0.E0,4.245563363410E-1)); -#32479=AXIS2_PLACEMENT_3D('',#32476,#32477,#32478); -#32480=PLANE('',#32479); -#32481=ORIENTED_EDGE('',*,*,#24898,.F.); -#32483=ORIENTED_EDGE('',*,*,#32482,.T.); -#32484=ORIENTED_EDGE('',*,*,#27916,.T.); -#32485=ORIENTED_EDGE('',*,*,#32469,.F.); -#32486=EDGE_LOOP('',(#32481,#32483,#32484,#32485)); -#32487=FACE_OUTER_BOUND('',#32486,.F.); -#32489=CARTESIAN_POINT('',(0.E0,1.55E0,2.718062138729E0)); -#32490=DIRECTION('',(4.395100215454E-1,0.E0,8.982376862285E-1)); -#32491=DIRECTION('',(8.982376862285E-1,0.E0,-4.395100215454E-1)); -#32492=AXIS2_PLACEMENT_3D('',#32489,#32490,#32491); -#32493=PLANE('',#32492); -#32494=ORIENTED_EDGE('',*,*,#24896,.F.); -#32496=ORIENTED_EDGE('',*,*,#32495,.T.); -#32497=ORIENTED_EDGE('',*,*,#27918,.T.); -#32498=ORIENTED_EDGE('',*,*,#32482,.F.); -#32499=EDGE_LOOP('',(#32494,#32496,#32497,#32498)); -#32500=FACE_OUTER_BOUND('',#32499,.F.); -#32502=CARTESIAN_POINT('',(0.E0,1.55E0,2.549041394881E0)); -#32503=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32504=DIRECTION('',(0.E0,0.E0,1.E0)); -#32505=AXIS2_PLACEMENT_3D('',#32502,#32503,#32504); -#32506=PLANE('',#32505); -#32507=ORIENTED_EDGE('',*,*,#24894,.F.); -#32509=ORIENTED_EDGE('',*,*,#32508,.T.); -#32510=ORIENTED_EDGE('',*,*,#27920,.T.); -#32511=ORIENTED_EDGE('',*,*,#32495,.F.); -#32512=EDGE_LOOP('',(#32507,#32509,#32510,#32511)); -#32513=FACE_OUTER_BOUND('',#32512,.F.); -#32515=CARTESIAN_POINT('',(8.085106611252E-1,1.55E0,2.154659874156E0)); -#32516=DIRECTION('',(-4.384111289239E-1,0.E0,-8.987745446082E-1)); -#32517=DIRECTION('',(-8.987745446082E-1,0.E0,4.384111289239E-1)); -#32518=AXIS2_PLACEMENT_3D('',#32515,#32516,#32517); -#32519=PLANE('',#32518); -#32520=ORIENTED_EDGE('',*,*,#24892,.F.); -#32522=ORIENTED_EDGE('',*,*,#32521,.T.); -#32523=ORIENTED_EDGE('',*,*,#27922,.T.); -#32524=ORIENTED_EDGE('',*,*,#32508,.F.); -#32525=EDGE_LOOP('',(#32520,#32522,#32523,#32524)); -#32526=FACE_OUTER_BOUND('',#32525,.F.); -#32528=CARTESIAN_POINT('',(0.E0,1.55E0,1.760278353432E0)); -#32529=DIRECTION('',(-4.384111289239E-1,0.E0,8.987745446082E-1)); -#32530=DIRECTION('',(8.987745446082E-1,0.E0,4.384111289239E-1)); -#32531=AXIS2_PLACEMENT_3D('',#32528,#32529,#32530); -#32532=PLANE('',#32531); -#32533=ORIENTED_EDGE('',*,*,#24890,.F.); -#32535=ORIENTED_EDGE('',*,*,#32534,.T.); -#32536=ORIENTED_EDGE('',*,*,#27924,.T.); -#32537=ORIENTED_EDGE('',*,*,#32521,.F.); -#32538=EDGE_LOOP('',(#32533,#32535,#32536,#32537)); -#32539=FACE_OUTER_BOUND('',#32538,.F.); -#32541=CARTESIAN_POINT('',(0.E0,1.55E0,1.591257609584E0)); -#32542=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32543=DIRECTION('',(0.E0,0.E0,1.E0)); -#32544=AXIS2_PLACEMENT_3D('',#32541,#32542,#32543); -#32545=PLANE('',#32544); -#32546=ORIENTED_EDGE('',*,*,#24888,.F.); -#32548=ORIENTED_EDGE('',*,*,#32547,.T.); -#32549=ORIENTED_EDGE('',*,*,#27926,.T.); -#32550=ORIENTED_EDGE('',*,*,#32534,.F.); -#32551=EDGE_LOOP('',(#32546,#32548,#32549,#32550)); -#32552=FACE_OUTER_BOUND('',#32551,.F.); -#32554=CARTESIAN_POINT('',(9.787234067917E-1,1.55E0,2.070149502232E0)); -#32555=DIRECTION('',(4.395100215454E-1,0.E0,-8.982376862285E-1)); -#32556=DIRECTION('',(-8.982376862285E-1,0.E0,-4.395100215454E-1)); -#32557=AXIS2_PLACEMENT_3D('',#32554,#32555,#32556); -#32558=PLANE('',#32557); -#32559=ORIENTED_EDGE('',*,*,#24886,.F.); -#32561=ORIENTED_EDGE('',*,*,#32560,.T.); -#32562=ORIENTED_EDGE('',*,*,#27928,.T.); -#32563=ORIENTED_EDGE('',*,*,#32547,.F.); -#32564=EDGE_LOOP('',(#32559,#32561,#32562,#32563)); -#32565=FACE_OUTER_BOUND('',#32564,.F.); -#32567=CARTESIAN_POINT('',(2.E0,1.55E0,1.591257609584E0)); -#32568=DIRECTION('',(-4.245563363410E-1,0.E0,-9.054015226808E-1)); -#32569=DIRECTION('',(-9.054015226808E-1,0.E0,4.245563363410E-1)); -#32570=AXIS2_PLACEMENT_3D('',#32567,#32568,#32569); -#32571=PLANE('',#32570); -#32572=ORIENTED_EDGE('',*,*,#24884,.F.); -#32573=ORIENTED_EDGE('',*,*,#32432,.T.); -#32574=ORIENTED_EDGE('',*,*,#27930,.T.); -#32575=ORIENTED_EDGE('',*,*,#32560,.F.); -#32576=EDGE_LOOP('',(#32572,#32573,#32574,#32575)); -#32577=FACE_OUTER_BOUND('',#32576,.F.); -#32579=CARTESIAN_POINT('',(4.E0,1.55E0,1.03375E1)); -#32580=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32581=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32582=AXIS2_PLACEMENT_3D('',#32579,#32580,#32581); -#32583=PLANE('',#32582); -#32584=ORIENTED_EDGE('',*,*,#24908,.F.); -#32586=ORIENTED_EDGE('',*,*,#32585,.T.); -#32587=ORIENTED_EDGE('',*,*,#27947,.T.); -#32589=ORIENTED_EDGE('',*,*,#32588,.F.); -#32590=EDGE_LOOP('',(#32584,#32586,#32587,#32589)); -#32591=FACE_OUTER_BOUND('',#32590,.F.); -#32593=CARTESIAN_POINT('',(4.E0,1.55E0,1.045E1)); -#32594=DIRECTION('',(1.E0,0.E0,0.E0)); -#32595=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32596=AXIS2_PLACEMENT_3D('',#32593,#32594,#32595); -#32597=PLANE('',#32596); -#32598=ORIENTED_EDGE('',*,*,#24926,.F.); -#32600=ORIENTED_EDGE('',*,*,#32599,.T.); -#32601=ORIENTED_EDGE('',*,*,#27949,.T.); -#32602=ORIENTED_EDGE('',*,*,#32585,.F.); -#32603=EDGE_LOOP('',(#32598,#32600,#32601,#32602)); -#32604=FACE_OUTER_BOUND('',#32603,.F.); -#32606=CARTESIAN_POINT('',(3.E0,1.55E0,1.045E1)); -#32607=DIRECTION('',(0.E0,0.E0,1.E0)); -#32608=DIRECTION('',(1.E0,0.E0,0.E0)); -#32609=AXIS2_PLACEMENT_3D('',#32606,#32607,#32608); -#32610=PLANE('',#32609); -#32611=ORIENTED_EDGE('',*,*,#24924,.F.); -#32613=ORIENTED_EDGE('',*,*,#32612,.T.); -#32614=ORIENTED_EDGE('',*,*,#27951,.T.); -#32615=ORIENTED_EDGE('',*,*,#32599,.F.); -#32616=EDGE_LOOP('',(#32611,#32613,#32614,#32615)); -#32617=FACE_OUTER_BOUND('',#32616,.F.); -#32619=CARTESIAN_POINT('',(3.E0,1.55E0,9.775E0)); -#32620=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32621=DIRECTION('',(0.E0,0.E0,1.E0)); -#32622=AXIS2_PLACEMENT_3D('',#32619,#32620,#32621); -#32623=PLANE('',#32622); -#32624=ORIENTED_EDGE('',*,*,#24922,.F.); -#32626=ORIENTED_EDGE('',*,*,#32625,.T.); -#32627=ORIENTED_EDGE('',*,*,#27953,.T.); -#32628=ORIENTED_EDGE('',*,*,#32612,.F.); -#32629=EDGE_LOOP('',(#32624,#32626,#32627,#32628)); -#32630=FACE_OUTER_BOUND('',#32629,.F.); -#32632=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.775E0)); -#32633=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32634=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32635=AXIS2_PLACEMENT_3D('',#32632,#32633,#32634); -#32636=PLANE('',#32635); -#32637=ORIENTED_EDGE('',*,*,#24920,.F.); -#32639=ORIENTED_EDGE('',*,*,#32638,.T.); -#32640=ORIENTED_EDGE('',*,*,#27955,.T.); -#32641=ORIENTED_EDGE('',*,*,#32625,.F.); -#32642=EDGE_LOOP('',(#32637,#32639,#32640,#32641)); -#32643=FACE_OUTER_BOUND('',#32642,.F.); -#32645=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.03375E1)); -#32646=DIRECTION('',(1.E0,0.E0,0.E0)); -#32647=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32648=AXIS2_PLACEMENT_3D('',#32645,#32646,#32647); -#32649=PLANE('',#32648); -#32650=ORIENTED_EDGE('',*,*,#24918,.F.); -#32652=ORIENTED_EDGE('',*,*,#32651,.T.); -#32653=ORIENTED_EDGE('',*,*,#27957,.T.); -#32654=ORIENTED_EDGE('',*,*,#32638,.F.); -#32655=EDGE_LOOP('',(#32650,#32652,#32653,#32654)); -#32656=FACE_OUTER_BOUND('',#32655,.F.); -#32658=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.03375E1)); -#32659=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32660=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32661=AXIS2_PLACEMENT_3D('',#32658,#32659,#32660); -#32662=PLANE('',#32661); -#32663=ORIENTED_EDGE('',*,*,#24916,.F.); -#32665=ORIENTED_EDGE('',*,*,#32664,.T.); -#32666=ORIENTED_EDGE('',*,*,#27959,.T.); -#32667=ORIENTED_EDGE('',*,*,#32651,.F.); -#32668=EDGE_LOOP('',(#32663,#32665,#32666,#32667)); -#32669=FACE_OUTER_BOUND('',#32668,.F.); -#32671=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,9.849999982119E0)); -#32672=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32673=DIRECTION('',(0.E0,0.E0,1.E0)); -#32674=AXIS2_PLACEMENT_3D('',#32671,#32672,#32673); -#32675=PLANE('',#32674); -#32676=ORIENTED_EDGE('',*,*,#24914,.F.); -#32678=ORIENTED_EDGE('',*,*,#32677,.T.); -#32679=ORIENTED_EDGE('',*,*,#27961,.T.); -#32680=ORIENTED_EDGE('',*,*,#32664,.F.); -#32681=EDGE_LOOP('',(#32676,#32678,#32679,#32680)); -#32682=FACE_OUTER_BOUND('',#32681,.F.); -#32684=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,9.849999982119E0)); -#32685=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32686=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32687=AXIS2_PLACEMENT_3D('',#32684,#32685,#32686); -#32688=PLANE('',#32687); -#32689=ORIENTED_EDGE('',*,*,#24912,.F.); -#32691=ORIENTED_EDGE('',*,*,#32690,.T.); -#32692=ORIENTED_EDGE('',*,*,#27963,.T.); -#32693=ORIENTED_EDGE('',*,*,#32677,.F.); -#32694=EDGE_LOOP('',(#32689,#32691,#32692,#32693)); -#32695=FACE_OUTER_BOUND('',#32694,.F.); -#32697=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.03375E1)); -#32698=DIRECTION('',(1.E0,0.E0,0.E0)); -#32699=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32700=AXIS2_PLACEMENT_3D('',#32697,#32698,#32699); -#32701=PLANE('',#32700); -#32702=ORIENTED_EDGE('',*,*,#24910,.F.); -#32703=ORIENTED_EDGE('',*,*,#32588,.T.); -#32704=ORIENTED_EDGE('',*,*,#27965,.T.); -#32705=ORIENTED_EDGE('',*,*,#32690,.F.); -#32706=EDGE_LOOP('',(#32702,#32703,#32704,#32705)); -#32707=FACE_OUTER_BOUND('',#32706,.F.); -#32709=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.893750035763E0)); -#32710=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32711=DIRECTION('',(0.E0,0.E0,1.E0)); -#32712=AXIS2_PLACEMENT_3D('',#32709,#32710,#32711); -#32713=PLANE('',#32712); -#32714=ORIENTED_EDGE('',*,*,#24930,.F.); -#32716=ORIENTED_EDGE('',*,*,#32715,.T.); -#32717=ORIENTED_EDGE('',*,*,#27982,.T.); -#32719=ORIENTED_EDGE('',*,*,#32718,.F.); -#32720=EDGE_LOOP('',(#32714,#32716,#32717,#32719)); -#32721=FACE_OUTER_BOUND('',#32720,.F.); -#32723=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.912499964237E0)); -#32724=DIRECTION('',(1.735740053062E-1,0.E0,-9.848208287206E-1)); -#32725=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#32726=AXIS2_PLACEMENT_3D('',#32723,#32724,#32725); -#32727=PLANE('',#32726); -#32728=ORIENTED_EDGE('',*,*,#25008,.F.); -#32730=ORIENTED_EDGE('',*,*,#32729,.T.); -#32731=ORIENTED_EDGE('',*,*,#27984,.T.); -#32732=ORIENTED_EDGE('',*,*,#32715,.F.); -#32733=EDGE_LOOP('',(#32728,#32730,#32731,#32732)); -#32734=FACE_OUTER_BOUND('',#32733,.F.); -#32736=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.9875E0)); -#32737=DIRECTION('',(6.611564428881E-1,0.E0,-7.502480643277E-1)); -#32738=DIRECTION('',(-7.502480643277E-1,0.E0,-6.611564428881E-1)); -#32739=AXIS2_PLACEMENT_3D('',#32736,#32737,#32738); -#32740=PLANE('',#32739); -#32741=ORIENTED_EDGE('',*,*,#25006,.F.); -#32743=ORIENTED_EDGE('',*,*,#32742,.T.); -#32744=ORIENTED_EDGE('',*,*,#27986,.T.); -#32745=ORIENTED_EDGE('',*,*,#32729,.F.); -#32746=EDGE_LOOP('',(#32741,#32743,#32744,#32745)); -#32747=FACE_OUTER_BOUND('',#32746,.F.); -#32749=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.062500035763E0)); -#32750=DIRECTION('',(8.697575726745E-1,0.E0,-4.934792445233E-1)); -#32751=DIRECTION('',(-4.934792445233E-1,0.E0,-8.697575726745E-1)); -#32752=AXIS2_PLACEMENT_3D('',#32749,#32750,#32751); -#32753=PLANE('',#32752); -#32754=ORIENTED_EDGE('',*,*,#25004,.F.); -#32756=ORIENTED_EDGE('',*,*,#32755,.T.); -#32757=ORIENTED_EDGE('',*,*,#27988,.T.); -#32758=ORIENTED_EDGE('',*,*,#32742,.F.); -#32759=EDGE_LOOP('',(#32754,#32756,#32757,#32758)); -#32760=FACE_OUTER_BOUND('',#32759,.F.); -#32762=CARTESIAN_POINT('',(4.E0,1.55E0,9.15625E0)); -#32763=DIRECTION('',(9.752007335099E-1,0.E0,-2.213222297055E-1)); -#32764=DIRECTION('',(-2.213222297055E-1,0.E0,-9.752007335099E-1)); -#32765=AXIS2_PLACEMENT_3D('',#32762,#32763,#32764); -#32766=PLANE('',#32765); -#32767=ORIENTED_EDGE('',*,*,#25002,.F.); -#32769=ORIENTED_EDGE('',*,*,#32768,.T.); -#32770=ORIENTED_EDGE('',*,*,#27990,.T.); -#32771=ORIENTED_EDGE('',*,*,#32755,.F.); -#32772=EDGE_LOOP('',(#32767,#32769,#32770,#32771)); -#32773=FACE_OUTER_BOUND('',#32772,.F.); -#32775=CARTESIAN_POINT('',(4.E0,1.55E0,9.325E0)); -#32776=DIRECTION('',(1.E0,0.E0,0.E0)); -#32777=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32778=AXIS2_PLACEMENT_3D('',#32775,#32776,#32777); -#32779=PLANE('',#32778); -#32780=ORIENTED_EDGE('',*,*,#25000,.F.); -#32782=ORIENTED_EDGE('',*,*,#32781,.T.); -#32783=ORIENTED_EDGE('',*,*,#27992,.T.); -#32784=ORIENTED_EDGE('',*,*,#32768,.F.); -#32785=EDGE_LOOP('',(#32780,#32782,#32783,#32784)); -#32786=FACE_OUTER_BOUND('',#32785,.F.); -#32788=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.418749964237E0)); -#32789=DIRECTION('',(9.752007335099E-1,0.E0,2.213222297055E-1)); -#32790=DIRECTION('',(2.213222297055E-1,0.E0,-9.752007335099E-1)); -#32791=AXIS2_PLACEMENT_3D('',#32788,#32789,#32790); -#32792=PLANE('',#32791); -#32793=ORIENTED_EDGE('',*,*,#24998,.F.); -#32795=ORIENTED_EDGE('',*,*,#32794,.T.); -#32796=ORIENTED_EDGE('',*,*,#27994,.T.); -#32797=ORIENTED_EDGE('',*,*,#32781,.F.); -#32798=EDGE_LOOP('',(#32793,#32795,#32796,#32797)); -#32799=FACE_OUTER_BOUND('',#32798,.F.); -#32801=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,9.49375E0)); -#32802=DIRECTION('',(8.697575726745E-1,0.E0,4.934792445233E-1)); -#32803=DIRECTION('',(4.934792445233E-1,0.E0,-8.697575726745E-1)); -#32804=AXIS2_PLACEMENT_3D('',#32801,#32802,#32803); -#32805=PLANE('',#32804); -#32806=ORIENTED_EDGE('',*,*,#24996,.F.); -#32808=ORIENTED_EDGE('',*,*,#32807,.T.); -#32809=ORIENTED_EDGE('',*,*,#27996,.T.); -#32810=ORIENTED_EDGE('',*,*,#32794,.F.); -#32811=EDGE_LOOP('',(#32806,#32808,#32809,#32810)); -#32812=FACE_OUTER_BOUND('',#32811,.F.); -#32814=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.568749982119E0)); -#32815=DIRECTION('',(6.611561767082E-1,0.E0,7.502482988989E-1)); -#32816=DIRECTION('',(7.502482988989E-1,0.E0,-6.611561767082E-1)); -#32817=AXIS2_PLACEMENT_3D('',#32814,#32815,#32816); -#32818=PLANE('',#32817); -#32819=ORIENTED_EDGE('',*,*,#24994,.F.); -#32821=ORIENTED_EDGE('',*,*,#32820,.T.); -#32822=ORIENTED_EDGE('',*,*,#27998,.T.); -#32823=ORIENTED_EDGE('',*,*,#32807,.F.); -#32824=EDGE_LOOP('',(#32819,#32821,#32822,#32823)); -#32825=FACE_OUTER_BOUND('',#32824,.F.); -#32827=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,9.60625E0)); -#32828=DIRECTION('',(4.032178735094E-1,0.E0,9.151040085600E-1)); -#32829=DIRECTION('',(9.151040085600E-1,0.E0,-4.032178735094E-1)); -#32830=AXIS2_PLACEMENT_3D('',#32827,#32828,#32829); -#32831=PLANE('',#32830); -#32832=ORIENTED_EDGE('',*,*,#24992,.F.); -#32834=ORIENTED_EDGE('',*,*,#32833,.T.); -#32835=ORIENTED_EDGE('',*,*,#28000,.T.); -#32836=ORIENTED_EDGE('',*,*,#32820,.F.); -#32837=EDGE_LOOP('',(#32832,#32834,#32835,#32836)); -#32838=FACE_OUTER_BOUND('',#32837,.F.); -#32840=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.624999982119E0)); -#32841=DIRECTION('',(1.735745105259E-1,0.E0,9.848207396759E-1)); -#32842=DIRECTION('',(9.848207396759E-1,0.E0,-1.735745105259E-1)); -#32843=AXIS2_PLACEMENT_3D('',#32840,#32841,#32842); -#32844=PLANE('',#32843); -#32845=ORIENTED_EDGE('',*,*,#24990,.F.); -#32847=ORIENTED_EDGE('',*,*,#32846,.T.); -#32848=ORIENTED_EDGE('',*,*,#28002,.T.); -#32849=ORIENTED_EDGE('',*,*,#32833,.F.); -#32850=EDGE_LOOP('',(#32845,#32847,#32848,#32849)); -#32851=FACE_OUTER_BOUND('',#32850,.F.); -#32853=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.624999982119E0)); -#32854=DIRECTION('',(0.E0,0.E0,1.E0)); -#32855=DIRECTION('',(1.E0,0.E0,0.E0)); -#32856=AXIS2_PLACEMENT_3D('',#32853,#32854,#32855); -#32857=PLANE('',#32856); -#32858=ORIENTED_EDGE('',*,*,#24988,.F.); -#32860=ORIENTED_EDGE('',*,*,#32859,.T.); -#32861=ORIENTED_EDGE('',*,*,#28004,.T.); -#32862=ORIENTED_EDGE('',*,*,#32846,.F.); -#32863=EDGE_LOOP('',(#32858,#32860,#32861,#32862)); -#32864=FACE_OUTER_BOUND('',#32863,.F.); -#32866=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,9.60625E0)); -#32867=DIRECTION('',(-1.735744162049E-1,0.E0,9.848207562999E-1)); -#32868=DIRECTION('',(9.848207562999E-1,0.E0,1.735744162049E-1)); -#32869=AXIS2_PLACEMENT_3D('',#32866,#32867,#32868); -#32870=PLANE('',#32869); -#32871=ORIENTED_EDGE('',*,*,#24986,.F.); -#32873=ORIENTED_EDGE('',*,*,#32872,.T.); -#32874=ORIENTED_EDGE('',*,*,#28006,.T.); -#32875=ORIENTED_EDGE('',*,*,#32859,.F.); -#32876=EDGE_LOOP('',(#32871,#32873,#32874,#32875)); -#32877=FACE_OUTER_BOUND('',#32876,.F.); -#32879=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.568749982119E0)); -#32880=DIRECTION('',(-4.032179326300E-1,0.E0,9.151039825100E-1)); -#32881=DIRECTION('',(9.151039825100E-1,0.E0,4.032179326300E-1)); -#32882=AXIS2_PLACEMENT_3D('',#32879,#32880,#32881); -#32883=PLANE('',#32882); -#32884=ORIENTED_EDGE('',*,*,#24984,.F.); -#32886=ORIENTED_EDGE('',*,*,#32885,.T.); -#32887=ORIENTED_EDGE('',*,*,#28008,.T.); -#32888=ORIENTED_EDGE('',*,*,#32872,.F.); -#32889=EDGE_LOOP('',(#32884,#32886,#32887,#32888)); -#32890=FACE_OUTER_BOUND('',#32889,.F.); -#32892=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,9.49375E0)); -#32893=DIRECTION('',(-6.611562092875E-1,0.E0,7.502482701883E-1)); -#32894=DIRECTION('',(7.502482701883E-1,0.E0,6.611562092875E-1)); -#32895=AXIS2_PLACEMENT_3D('',#32892,#32893,#32894); -#32896=PLANE('',#32895); -#32897=ORIENTED_EDGE('',*,*,#24982,.F.); -#32899=ORIENTED_EDGE('',*,*,#32898,.T.); -#32900=ORIENTED_EDGE('',*,*,#28010,.T.); -#32901=ORIENTED_EDGE('',*,*,#32885,.F.); -#32902=EDGE_LOOP('',(#32897,#32899,#32900,#32901)); -#32903=FACE_OUTER_BOUND('',#32902,.F.); -#32905=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.418749964237E0)); -#32906=DIRECTION('',(-8.697576004880E-1,0.E0,4.934791955020E-1)); -#32907=DIRECTION('',(4.934791955020E-1,0.E0,8.697576004880E-1)); -#32908=AXIS2_PLACEMENT_3D('',#32905,#32906,#32907); -#32909=PLANE('',#32908); -#32910=ORIENTED_EDGE('',*,*,#24980,.F.); -#32912=ORIENTED_EDGE('',*,*,#32911,.T.); -#32913=ORIENTED_EDGE('',*,*,#28012,.T.); -#32914=ORIENTED_EDGE('',*,*,#32898,.F.); -#32915=EDGE_LOOP('',(#32910,#32912,#32913,#32914)); -#32916=FACE_OUTER_BOUND('',#32915,.F.); -#32918=CARTESIAN_POINT('',(3.E0,1.55E0,9.325E0)); -#32919=DIRECTION('',(-9.752007376918E-1,0.E0,2.213222112791E-1)); -#32920=DIRECTION('',(2.213222112791E-1,0.E0,9.752007376918E-1)); -#32921=AXIS2_PLACEMENT_3D('',#32918,#32919,#32920); -#32922=PLANE('',#32921); -#32923=ORIENTED_EDGE('',*,*,#24978,.F.); -#32925=ORIENTED_EDGE('',*,*,#32924,.T.); -#32926=ORIENTED_EDGE('',*,*,#28014,.T.); -#32927=ORIENTED_EDGE('',*,*,#32911,.F.); -#32928=EDGE_LOOP('',(#32923,#32925,#32926,#32927)); -#32929=FACE_OUTER_BOUND('',#32928,.F.); -#32931=CARTESIAN_POINT('',(3.E0,1.55E0,9.15625E0)); -#32932=DIRECTION('',(-1.E0,0.E0,0.E0)); -#32933=DIRECTION('',(0.E0,0.E0,1.E0)); -#32934=AXIS2_PLACEMENT_3D('',#32931,#32932,#32933); -#32935=PLANE('',#32934); -#32936=ORIENTED_EDGE('',*,*,#24976,.F.); -#32938=ORIENTED_EDGE('',*,*,#32937,.T.); -#32939=ORIENTED_EDGE('',*,*,#28016,.T.); -#32940=ORIENTED_EDGE('',*,*,#32924,.F.); -#32941=EDGE_LOOP('',(#32936,#32938,#32939,#32940)); -#32942=FACE_OUTER_BOUND('',#32941,.F.); -#32944=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.062500035763E0)); -#32945=DIRECTION('',(-9.752007376918E-1,0.E0,-2.213222112791E-1)); -#32946=DIRECTION('',(-2.213222112791E-1,0.E0,9.752007376918E-1)); -#32947=AXIS2_PLACEMENT_3D('',#32944,#32945,#32946); -#32948=PLANE('',#32947); -#32949=ORIENTED_EDGE('',*,*,#24974,.F.); -#32951=ORIENTED_EDGE('',*,*,#32950,.T.); -#32952=ORIENTED_EDGE('',*,*,#28018,.T.); -#32953=ORIENTED_EDGE('',*,*,#32937,.F.); -#32954=EDGE_LOOP('',(#32949,#32951,#32952,#32953)); -#32955=FACE_OUTER_BOUND('',#32954,.F.); -#32957=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.9875E0)); -#32958=DIRECTION('',(-8.697576004880E-1,0.E0,-4.934791955020E-1)); -#32959=DIRECTION('',(-4.934791955020E-1,0.E0,8.697576004880E-1)); -#32960=AXIS2_PLACEMENT_3D('',#32957,#32958,#32959); -#32961=PLANE('',#32960); -#32962=ORIENTED_EDGE('',*,*,#24972,.F.); -#32964=ORIENTED_EDGE('',*,*,#32963,.T.); -#32965=ORIENTED_EDGE('',*,*,#28020,.T.); -#32966=ORIENTED_EDGE('',*,*,#32950,.F.); -#32967=EDGE_LOOP('',(#32962,#32964,#32965,#32966)); -#32968=FACE_OUTER_BOUND('',#32967,.F.); -#32970=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.912499964237E0)); -#32971=DIRECTION('',(-6.611564754674E-1,0.E0,-7.502480356172E-1)); -#32972=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#32973=AXIS2_PLACEMENT_3D('',#32970,#32971,#32972); -#32974=PLANE('',#32973); -#32975=ORIENTED_EDGE('',*,*,#24970,.F.); -#32977=ORIENTED_EDGE('',*,*,#32976,.T.); -#32978=ORIENTED_EDGE('',*,*,#28022,.T.); -#32979=ORIENTED_EDGE('',*,*,#32963,.F.); -#32980=EDGE_LOOP('',(#32975,#32977,#32978,#32979)); -#32981=FACE_OUTER_BOUND('',#32980,.F.); -#32983=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.893750035763E0)); -#32984=DIRECTION('',(-1.735739345657E-1,0.E0,-9.848208411886E-1)); -#32985=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#32986=AXIS2_PLACEMENT_3D('',#32983,#32984,#32985); -#32987=PLANE('',#32986); -#32988=ORIENTED_EDGE('',*,*,#24968,.F.); -#32990=ORIENTED_EDGE('',*,*,#32989,.T.); -#32991=ORIENTED_EDGE('',*,*,#28024,.T.); -#32992=ORIENTED_EDGE('',*,*,#32976,.F.); -#32993=EDGE_LOOP('',(#32988,#32990,#32991,#32992)); -#32994=FACE_OUTER_BOUND('',#32993,.F.); -#32996=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.006250035763E0)); -#32997=DIRECTION('',(1.E0,0.E0,0.E0)); -#32998=DIRECTION('',(0.E0,0.E0,-1.E0)); -#32999=AXIS2_PLACEMENT_3D('',#32996,#32997,#32998); -#33000=PLANE('',#32999); -#33001=ORIENTED_EDGE('',*,*,#24966,.F.); -#33003=ORIENTED_EDGE('',*,*,#33002,.T.); -#33004=ORIENTED_EDGE('',*,*,#28026,.T.); -#33005=ORIENTED_EDGE('',*,*,#32989,.F.); -#33006=EDGE_LOOP('',(#33001,#33003,#33004,#33005)); -#33007=FACE_OUTER_BOUND('',#33006,.F.); -#33009=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.024999964237E0)); -#33010=DIRECTION('',(2.818404483901E-1,0.E0,9.594612872082E-1)); -#33011=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#33012=AXIS2_PLACEMENT_3D('',#33009,#33010,#33011); -#33013=PLANE('',#33012); -#33014=ORIENTED_EDGE('',*,*,#24964,.F.); -#33016=ORIENTED_EDGE('',*,*,#33015,.T.); -#33017=ORIENTED_EDGE('',*,*,#28028,.T.); -#33018=ORIENTED_EDGE('',*,*,#33002,.F.); -#33019=EDGE_LOOP('',(#33014,#33016,#33017,#33018)); -#33020=FACE_OUTER_BOUND('',#33019,.F.); -#33022=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.081249964237E0)); -#33023=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#33024=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#33025=AXIS2_PLACEMENT_3D('',#33022,#33023,#33024); -#33026=PLANE('',#33025); -#33027=ORIENTED_EDGE('',*,*,#24962,.F.); -#33029=ORIENTED_EDGE('',*,*,#33028,.T.); -#33030=ORIENTED_EDGE('',*,*,#28030,.T.); -#33031=ORIENTED_EDGE('',*,*,#33015,.F.); -#33032=EDGE_LOOP('',(#33027,#33029,#33030,#33031)); -#33033=FACE_OUTER_BOUND('',#33032,.F.); -#33035=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.15625E0)); -#33036=DIRECTION('',(9.620372415242E-1,0.E0,2.729182037179E-1)); -#33037=DIRECTION('',(2.729182037179E-1,0.E0,-9.620372415242E-1)); -#33038=AXIS2_PLACEMENT_3D('',#33035,#33036,#33037); -#33039=PLANE('',#33038); -#33040=ORIENTED_EDGE('',*,*,#24960,.F.); -#33042=ORIENTED_EDGE('',*,*,#33041,.T.); -#33043=ORIENTED_EDGE('',*,*,#28032,.T.); -#33044=ORIENTED_EDGE('',*,*,#33028,.F.); -#33045=EDGE_LOOP('',(#33040,#33042,#33043,#33044)); -#33046=FACE_OUTER_BOUND('',#33045,.F.); -#33048=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.325E0)); -#33049=DIRECTION('',(1.E0,0.E0,0.E0)); -#33050=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33051=AXIS2_PLACEMENT_3D('',#33048,#33049,#33050); -#33052=PLANE('',#33051); -#33053=ORIENTED_EDGE('',*,*,#24958,.F.); -#33055=ORIENTED_EDGE('',*,*,#33054,.T.); -#33056=ORIENTED_EDGE('',*,*,#28034,.T.); -#33057=ORIENTED_EDGE('',*,*,#33041,.F.); -#33058=EDGE_LOOP('',(#33053,#33055,#33056,#33057)); -#33059=FACE_OUTER_BOUND('',#33058,.F.); -#33061=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,9.400000035763E0)); -#33062=DIRECTION('',(9.620372415242E-1,0.E0,-2.729182037179E-1)); -#33063=DIRECTION('',(-2.729182037179E-1,0.E0,-9.620372415242E-1)); -#33064=AXIS2_PLACEMENT_3D('',#33061,#33062,#33063); -#33065=PLANE('',#33064); -#33066=ORIENTED_EDGE('',*,*,#24956,.F.); -#33068=ORIENTED_EDGE('',*,*,#33067,.T.); -#33069=ORIENTED_EDGE('',*,*,#28036,.T.); -#33070=ORIENTED_EDGE('',*,*,#33054,.F.); -#33071=EDGE_LOOP('',(#33066,#33068,#33069,#33070)); -#33072=FACE_OUTER_BOUND('',#33071,.F.); -#33074=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,9.456250035763E0)); -#33075=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#33076=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#33077=AXIS2_PLACEMENT_3D('',#33074,#33075,#33076); -#33078=PLANE('',#33077); -#33079=ORIENTED_EDGE('',*,*,#24954,.F.); -#33081=ORIENTED_EDGE('',*,*,#33080,.T.); -#33082=ORIENTED_EDGE('',*,*,#28038,.T.); -#33083=ORIENTED_EDGE('',*,*,#33067,.F.); -#33084=EDGE_LOOP('',(#33079,#33081,#33082,#33083)); -#33085=FACE_OUTER_BOUND('',#33084,.F.); -#33087=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,9.49375E0)); -#33088=DIRECTION('',(5.065483827484E-1,0.E0,-8.622115378113E-1)); -#33089=DIRECTION('',(-8.622115378113E-1,0.E0,-5.065483827484E-1)); -#33090=AXIS2_PLACEMENT_3D('',#33087,#33088,#33089); -#33091=PLANE('',#33090); -#33092=ORIENTED_EDGE('',*,*,#24952,.F.); -#33094=ORIENTED_EDGE('',*,*,#33093,.T.); -#33095=ORIENTED_EDGE('',*,*,#28040,.T.); -#33096=ORIENTED_EDGE('',*,*,#33080,.F.); -#33097=EDGE_LOOP('',(#33092,#33094,#33095,#33096)); -#33098=FACE_OUTER_BOUND('',#33097,.F.); -#33100=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,9.512500035763E0)); -#33101=DIRECTION('',(2.151532814605E-1,0.E0,-9.765802913621E-1)); -#33102=DIRECTION('',(-9.765802913621E-1,0.E0,-2.151532814605E-1)); -#33103=AXIS2_PLACEMENT_3D('',#33100,#33101,#33102); -#33104=PLANE('',#33103); -#33105=ORIENTED_EDGE('',*,*,#24950,.F.); -#33107=ORIENTED_EDGE('',*,*,#33106,.T.); -#33108=ORIENTED_EDGE('',*,*,#28042,.T.); -#33109=ORIENTED_EDGE('',*,*,#33093,.F.); -#33110=EDGE_LOOP('',(#33105,#33107,#33108,#33109)); -#33111=FACE_OUTER_BOUND('',#33110,.F.); -#33113=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,9.512500035763E0)); -#33114=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33115=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33116=AXIS2_PLACEMENT_3D('',#33113,#33114,#33115); -#33117=PLANE('',#33116); -#33118=ORIENTED_EDGE('',*,*,#24948,.F.); -#33120=ORIENTED_EDGE('',*,*,#33119,.T.); -#33121=ORIENTED_EDGE('',*,*,#28044,.T.); -#33122=ORIENTED_EDGE('',*,*,#33106,.F.); -#33123=EDGE_LOOP('',(#33118,#33120,#33121,#33122)); -#33124=FACE_OUTER_BOUND('',#33123,.F.); -#33126=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.49375E0)); -#33127=DIRECTION('',(-2.151532814605E-1,0.E0,-9.765802913621E-1)); -#33128=DIRECTION('',(-9.765802913621E-1,0.E0,2.151532814605E-1)); -#33129=AXIS2_PLACEMENT_3D('',#33126,#33127,#33128); -#33130=PLANE('',#33129); -#33131=ORIENTED_EDGE('',*,*,#24946,.F.); -#33133=ORIENTED_EDGE('',*,*,#33132,.T.); -#33134=ORIENTED_EDGE('',*,*,#28046,.T.); -#33135=ORIENTED_EDGE('',*,*,#33119,.F.); -#33136=EDGE_LOOP('',(#33131,#33133,#33134,#33135)); -#33137=FACE_OUTER_BOUND('',#33136,.F.); -#33139=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.456250035763E0)); -#33140=DIRECTION('',(-5.065487343940E-1,0.E0,-8.622113312198E-1)); -#33141=DIRECTION('',(-8.622113312198E-1,0.E0,5.065487343940E-1)); -#33142=AXIS2_PLACEMENT_3D('',#33139,#33140,#33141); -#33143=PLANE('',#33142); -#33144=ORIENTED_EDGE('',*,*,#24944,.F.); -#33146=ORIENTED_EDGE('',*,*,#33145,.T.); -#33147=ORIENTED_EDGE('',*,*,#28048,.T.); -#33148=ORIENTED_EDGE('',*,*,#33132,.F.); -#33149=EDGE_LOOP('',(#33144,#33146,#33147,#33148)); -#33150=FACE_OUTER_BOUND('',#33149,.F.); -#33152=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.400000035763E0)); -#33153=DIRECTION('',(-7.975043849272E-1,0.E0,-6.033131492201E-1)); -#33154=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#33155=AXIS2_PLACEMENT_3D('',#33152,#33153,#33154); -#33156=PLANE('',#33155); -#33157=ORIENTED_EDGE('',*,*,#24942,.F.); -#33159=ORIENTED_EDGE('',*,*,#33158,.T.); -#33160=ORIENTED_EDGE('',*,*,#28050,.T.); -#33161=ORIENTED_EDGE('',*,*,#33145,.F.); -#33162=EDGE_LOOP('',(#33157,#33159,#33160,#33161)); -#33163=FACE_OUTER_BOUND('',#33162,.F.); -#33165=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.325E0)); -#33166=DIRECTION('',(-9.620372415242E-1,0.E0,-2.729182037179E-1)); -#33167=DIRECTION('',(-2.729182037179E-1,0.E0,9.620372415242E-1)); -#33168=AXIS2_PLACEMENT_3D('',#33165,#33166,#33167); -#33169=PLANE('',#33168); -#33170=ORIENTED_EDGE('',*,*,#24940,.F.); -#33172=ORIENTED_EDGE('',*,*,#33171,.T.); -#33173=ORIENTED_EDGE('',*,*,#28052,.T.); -#33174=ORIENTED_EDGE('',*,*,#33158,.F.); -#33175=EDGE_LOOP('',(#33170,#33172,#33173,#33174)); -#33176=FACE_OUTER_BOUND('',#33175,.F.); -#33178=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.15625E0)); -#33179=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33180=DIRECTION('',(0.E0,0.E0,1.E0)); -#33181=AXIS2_PLACEMENT_3D('',#33178,#33179,#33180); -#33182=PLANE('',#33181); -#33183=ORIENTED_EDGE('',*,*,#24938,.F.); -#33185=ORIENTED_EDGE('',*,*,#33184,.T.); -#33186=ORIENTED_EDGE('',*,*,#28054,.T.); -#33187=ORIENTED_EDGE('',*,*,#33171,.F.); -#33188=EDGE_LOOP('',(#33183,#33185,#33186,#33187)); -#33189=FACE_OUTER_BOUND('',#33188,.F.); -#33191=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,9.081249964237E0)); -#33192=DIRECTION('',(-9.620372415242E-1,0.E0,2.729182037179E-1)); -#33193=DIRECTION('',(2.729182037179E-1,0.E0,9.620372415242E-1)); -#33194=AXIS2_PLACEMENT_3D('',#33191,#33192,#33193); -#33195=PLANE('',#33194); -#33196=ORIENTED_EDGE('',*,*,#24936,.F.); -#33198=ORIENTED_EDGE('',*,*,#33197,.T.); -#33199=ORIENTED_EDGE('',*,*,#28056,.T.); -#33200=ORIENTED_EDGE('',*,*,#33184,.F.); -#33201=EDGE_LOOP('',(#33196,#33198,#33199,#33200)); -#33202=FACE_OUTER_BOUND('',#33201,.F.); -#33204=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,9.024999964237E0)); -#33205=DIRECTION('',(-7.975043849273E-1,0.E0,6.033131492200E-1)); -#33206=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#33207=AXIS2_PLACEMENT_3D('',#33204,#33205,#33206); -#33208=PLANE('',#33207); -#33209=ORIENTED_EDGE('',*,*,#24934,.F.); -#33211=ORIENTED_EDGE('',*,*,#33210,.T.); -#33212=ORIENTED_EDGE('',*,*,#28058,.T.); -#33213=ORIENTED_EDGE('',*,*,#33197,.F.); -#33214=EDGE_LOOP('',(#33209,#33211,#33212,#33213)); -#33215=FACE_OUTER_BOUND('',#33214,.F.); -#33217=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,9.006250035763E0)); -#33218=DIRECTION('',(-2.818406906687E-1,0.E0,9.594612160392E-1)); -#33219=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906687E-1)); -#33220=AXIS2_PLACEMENT_3D('',#33217,#33218,#33219); -#33221=PLANE('',#33220); -#33222=ORIENTED_EDGE('',*,*,#24932,.F.); -#33223=ORIENTED_EDGE('',*,*,#32718,.T.); -#33224=ORIENTED_EDGE('',*,*,#28060,.T.); -#33225=ORIENTED_EDGE('',*,*,#33210,.F.); -#33226=EDGE_LOOP('',(#33222,#33223,#33224,#33225)); -#33227=FACE_OUTER_BOUND('',#33226,.F.); -#33229=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.012500071526E0)); -#33230=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33231=DIRECTION('',(0.E0,0.E0,1.E0)); -#33232=AXIS2_PLACEMENT_3D('',#33229,#33230,#33231); -#33233=PLANE('',#33232); -#33234=ORIENTED_EDGE('',*,*,#25012,.F.); -#33236=ORIENTED_EDGE('',*,*,#33235,.T.); -#33237=ORIENTED_EDGE('',*,*,#28077,.T.); -#33239=ORIENTED_EDGE('',*,*,#33238,.F.); -#33240=EDGE_LOOP('',(#33234,#33236,#33237,#33239)); -#33241=FACE_OUTER_BOUND('',#33240,.F.); -#33243=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.03125E0)); -#33244=DIRECTION('',(1.735740053062E-1,0.E0,-9.848208287206E-1)); -#33245=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#33246=AXIS2_PLACEMENT_3D('',#33243,#33244,#33245); -#33247=PLANE('',#33246); -#33248=ORIENTED_EDGE('',*,*,#25090,.F.); -#33250=ORIENTED_EDGE('',*,*,#33249,.T.); -#33251=ORIENTED_EDGE('',*,*,#28079,.T.); -#33252=ORIENTED_EDGE('',*,*,#33235,.F.); -#33253=EDGE_LOOP('',(#33248,#33250,#33251,#33252)); -#33254=FACE_OUTER_BOUND('',#33253,.F.); -#33256=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.106249928474E0)); -#33257=DIRECTION('',(6.611559105280E-1,0.E0,-7.502485334700E-1)); -#33258=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#33259=AXIS2_PLACEMENT_3D('',#33256,#33257,#33258); -#33260=PLANE('',#33259); -#33261=ORIENTED_EDGE('',*,*,#25088,.F.); -#33263=ORIENTED_EDGE('',*,*,#33262,.T.); -#33264=ORIENTED_EDGE('',*,*,#28081,.T.); -#33265=ORIENTED_EDGE('',*,*,#33249,.F.); -#33266=EDGE_LOOP('',(#33261,#33263,#33264,#33265)); -#33267=FACE_OUTER_BOUND('',#33266,.F.); -#33269=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.181250071526E0)); -#33270=DIRECTION('',(8.697578756632E-1,0.E0,-4.934787105051E-1)); -#33271=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#33272=AXIS2_PLACEMENT_3D('',#33269,#33270,#33271); -#33273=PLANE('',#33272); -#33274=ORIENTED_EDGE('',*,*,#25086,.F.); -#33276=ORIENTED_EDGE('',*,*,#33275,.T.); -#33277=ORIENTED_EDGE('',*,*,#28083,.T.); -#33278=ORIENTED_EDGE('',*,*,#33262,.F.); -#33279=EDGE_LOOP('',(#33274,#33276,#33277,#33278)); -#33280=FACE_OUTER_BOUND('',#33279,.F.); -#33282=CARTESIAN_POINT('',(4.E0,1.55E0,8.274999928474E0)); -#33283=DIRECTION('',(9.752006788427E-1,0.E0,-2.213224705823E-1)); -#33284=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#33285=AXIS2_PLACEMENT_3D('',#33282,#33283,#33284); -#33286=PLANE('',#33285); -#33287=ORIENTED_EDGE('',*,*,#25084,.F.); -#33289=ORIENTED_EDGE('',*,*,#33288,.T.); -#33290=ORIENTED_EDGE('',*,*,#28085,.T.); -#33291=ORIENTED_EDGE('',*,*,#33275,.F.); -#33292=EDGE_LOOP('',(#33287,#33289,#33290,#33291)); -#33293=FACE_OUTER_BOUND('',#33292,.F.); -#33295=CARTESIAN_POINT('',(4.E0,1.55E0,8.443749928474E0)); -#33296=DIRECTION('',(1.E0,0.E0,0.E0)); -#33297=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33298=AXIS2_PLACEMENT_3D('',#33295,#33296,#33297); -#33299=PLANE('',#33298); -#33300=ORIENTED_EDGE('',*,*,#25082,.F.); -#33302=ORIENTED_EDGE('',*,*,#33301,.T.); -#33303=ORIENTED_EDGE('',*,*,#28087,.T.); -#33304=ORIENTED_EDGE('',*,*,#33288,.F.); -#33305=EDGE_LOOP('',(#33300,#33302,#33303,#33304)); -#33306=FACE_OUTER_BOUND('',#33305,.F.); -#33308=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,8.5375E0)); -#33309=DIRECTION('',(9.752007881768E-1,0.E0,2.213219888292E-1)); -#33310=DIRECTION('',(2.213219888292E-1,0.E0,-9.752007881768E-1)); -#33311=AXIS2_PLACEMENT_3D('',#33308,#33309,#33310); -#33312=PLANE('',#33311); -#33313=ORIENTED_EDGE('',*,*,#25080,.F.); -#33315=ORIENTED_EDGE('',*,*,#33314,.T.); -#33316=ORIENTED_EDGE('',*,*,#28089,.T.); -#33317=ORIENTED_EDGE('',*,*,#33301,.F.); -#33318=EDGE_LOOP('',(#33313,#33315,#33316,#33317)); -#33319=FACE_OUTER_BOUND('',#33318,.F.); -#33321=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,8.612499928474E0)); -#33322=DIRECTION('',(8.697572696849E-1,0.E0,4.934797785425E-1)); -#33323=DIRECTION('',(4.934797785425E-1,0.E0,-8.697572696849E-1)); -#33324=AXIS2_PLACEMENT_3D('',#33321,#33322,#33323); -#33325=PLANE('',#33324); -#33326=ORIENTED_EDGE('',*,*,#25078,.F.); -#33328=ORIENTED_EDGE('',*,*,#33327,.T.); -#33329=ORIENTED_EDGE('',*,*,#28091,.T.); -#33330=ORIENTED_EDGE('',*,*,#33314,.F.); -#33331=EDGE_LOOP('',(#33326,#33328,#33329,#33330)); -#33332=FACE_OUTER_BOUND('',#33331,.F.); -#33334=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.687499964237E0)); -#33335=DIRECTION('',(6.611564428881E-1,0.E0,7.502480643277E-1)); -#33336=DIRECTION('',(7.502480643277E-1,0.E0,-6.611564428881E-1)); -#33337=AXIS2_PLACEMENT_3D('',#33334,#33335,#33336); -#33338=PLANE('',#33337); -#33339=ORIENTED_EDGE('',*,*,#25076,.F.); -#33341=ORIENTED_EDGE('',*,*,#33340,.T.); -#33342=ORIENTED_EDGE('',*,*,#28093,.T.); -#33343=ORIENTED_EDGE('',*,*,#33327,.F.); -#33344=EDGE_LOOP('',(#33339,#33341,#33342,#33343)); -#33345=FACE_OUTER_BOUND('',#33344,.F.); -#33347=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,8.725000035763E0)); -#33348=DIRECTION('',(4.032183565367E-1,0.E0,9.151037957258E-1)); -#33349=DIRECTION('',(9.151037957258E-1,0.E0,-4.032183565367E-1)); -#33350=AXIS2_PLACEMENT_3D('',#33347,#33348,#33349); -#33351=PLANE('',#33350); -#33352=ORIENTED_EDGE('',*,*,#25074,.F.); -#33354=ORIENTED_EDGE('',*,*,#33353,.T.); -#33355=ORIENTED_EDGE('',*,*,#28095,.T.); -#33356=ORIENTED_EDGE('',*,*,#33340,.F.); -#33357=EDGE_LOOP('',(#33352,#33354,#33355,#33356)); -#33358=FACE_OUTER_BOUND('',#33357,.F.); -#33360=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.743749964237E0)); -#33361=DIRECTION('',(1.735740288863E-1,0.E0,9.848208245646E-1)); -#33362=DIRECTION('',(9.848208245646E-1,0.E0,-1.735740288863E-1)); -#33363=AXIS2_PLACEMENT_3D('',#33360,#33361,#33362); -#33364=PLANE('',#33363); -#33365=ORIENTED_EDGE('',*,*,#25072,.F.); -#33367=ORIENTED_EDGE('',*,*,#33366,.T.); -#33368=ORIENTED_EDGE('',*,*,#28097,.T.); -#33369=ORIENTED_EDGE('',*,*,#33353,.F.); -#33370=EDGE_LOOP('',(#33365,#33367,#33368,#33369)); -#33371=FACE_OUTER_BOUND('',#33370,.F.); -#33373=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.743749964237E0)); -#33374=DIRECTION('',(0.E0,0.E0,1.E0)); -#33375=DIRECTION('',(1.E0,0.E0,0.E0)); -#33376=AXIS2_PLACEMENT_3D('',#33373,#33374,#33375); -#33377=PLANE('',#33376); -#33378=ORIENTED_EDGE('',*,*,#25070,.F.); -#33380=ORIENTED_EDGE('',*,*,#33379,.T.); -#33381=ORIENTED_EDGE('',*,*,#28099,.T.); -#33382=ORIENTED_EDGE('',*,*,#33366,.F.); -#33383=EDGE_LOOP('',(#33378,#33380,#33381,#33382)); -#33384=FACE_OUTER_BOUND('',#33383,.F.); -#33386=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,8.725000035763E0)); -#33387=DIRECTION('',(-1.735739345656E-1,0.E0,9.848208411886E-1)); -#33388=DIRECTION('',(9.848208411886E-1,0.E0,1.735739345656E-1)); -#33389=AXIS2_PLACEMENT_3D('',#33386,#33387,#33388); -#33390=PLANE('',#33389); -#33391=ORIENTED_EDGE('',*,*,#25068,.F.); -#33393=ORIENTED_EDGE('',*,*,#33392,.T.); -#33394=ORIENTED_EDGE('',*,*,#28101,.T.); -#33395=ORIENTED_EDGE('',*,*,#33379,.F.); -#33396=EDGE_LOOP('',(#33391,#33393,#33394,#33395)); -#33397=FACE_OUTER_BOUND('',#33396,.F.); -#33399=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.687499964237E0)); -#33400=DIRECTION('',(-4.032184156573E-1,0.E0,9.151037696758E-1)); -#33401=DIRECTION('',(9.151037696758E-1,0.E0,4.032184156573E-1)); -#33402=AXIS2_PLACEMENT_3D('',#33399,#33400,#33401); -#33403=PLANE('',#33402); -#33404=ORIENTED_EDGE('',*,*,#25066,.F.); -#33406=ORIENTED_EDGE('',*,*,#33405,.T.); -#33407=ORIENTED_EDGE('',*,*,#28103,.T.); -#33408=ORIENTED_EDGE('',*,*,#33392,.F.); -#33409=EDGE_LOOP('',(#33404,#33406,#33407,#33408)); -#33410=FACE_OUTER_BOUND('',#33409,.F.); -#33412=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.612499928474E0)); -#33413=DIRECTION('',(-6.611564754674E-1,0.E0,7.502480356172E-1)); -#33414=DIRECTION('',(7.502480356172E-1,0.E0,6.611564754674E-1)); -#33415=AXIS2_PLACEMENT_3D('',#33412,#33413,#33414); -#33416=PLANE('',#33415); -#33417=ORIENTED_EDGE('',*,*,#25064,.F.); -#33419=ORIENTED_EDGE('',*,*,#33418,.T.); -#33420=ORIENTED_EDGE('',*,*,#28105,.T.); -#33421=ORIENTED_EDGE('',*,*,#33405,.F.); -#33422=EDGE_LOOP('',(#33417,#33419,#33420,#33421)); -#33423=FACE_OUTER_BOUND('',#33422,.F.); -#33425=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.5375E0)); -#33426=DIRECTION('',(-8.697572974984E-1,0.E0,4.934797295212E-1)); -#33427=DIRECTION('',(4.934797295212E-1,0.E0,8.697572974984E-1)); -#33428=AXIS2_PLACEMENT_3D('',#33425,#33426,#33427); -#33429=PLANE('',#33428); -#33430=ORIENTED_EDGE('',*,*,#25062,.F.); -#33432=ORIENTED_EDGE('',*,*,#33431,.T.); -#33433=ORIENTED_EDGE('',*,*,#28107,.T.); -#33434=ORIENTED_EDGE('',*,*,#33418,.F.); -#33435=EDGE_LOOP('',(#33430,#33432,#33433,#33434)); -#33436=FACE_OUTER_BOUND('',#33435,.F.); -#33438=CARTESIAN_POINT('',(3.E0,1.55E0,8.443749928474E0)); -#33439=DIRECTION('',(-9.752007923587E-1,0.E0,2.213219704028E-1)); -#33440=DIRECTION('',(2.213219704028E-1,0.E0,9.752007923587E-1)); -#33441=AXIS2_PLACEMENT_3D('',#33438,#33439,#33440); -#33442=PLANE('',#33441); -#33443=ORIENTED_EDGE('',*,*,#25060,.F.); -#33445=ORIENTED_EDGE('',*,*,#33444,.T.); -#33446=ORIENTED_EDGE('',*,*,#28109,.T.); -#33447=ORIENTED_EDGE('',*,*,#33431,.F.); -#33448=EDGE_LOOP('',(#33443,#33445,#33446,#33447)); -#33449=FACE_OUTER_BOUND('',#33448,.F.); -#33451=CARTESIAN_POINT('',(3.E0,1.55E0,8.274999928474E0)); -#33452=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33453=DIRECTION('',(0.E0,0.E0,1.E0)); -#33454=AXIS2_PLACEMENT_3D('',#33451,#33452,#33453); -#33455=PLANE('',#33454); -#33456=ORIENTED_EDGE('',*,*,#25058,.F.); -#33458=ORIENTED_EDGE('',*,*,#33457,.T.); -#33459=ORIENTED_EDGE('',*,*,#28111,.T.); -#33460=ORIENTED_EDGE('',*,*,#33444,.F.); -#33461=EDGE_LOOP('',(#33456,#33458,#33459,#33460)); -#33462=FACE_OUTER_BOUND('',#33461,.F.); -#33464=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,8.181250071526E0)); -#33465=DIRECTION('',(-9.752006830246E-1,0.E0,-2.213224521559E-1)); -#33466=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#33467=AXIS2_PLACEMENT_3D('',#33464,#33465,#33466); -#33468=PLANE('',#33467); -#33469=ORIENTED_EDGE('',*,*,#25056,.F.); -#33471=ORIENTED_EDGE('',*,*,#33470,.T.); -#33472=ORIENTED_EDGE('',*,*,#28113,.T.); -#33473=ORIENTED_EDGE('',*,*,#33457,.F.); -#33474=EDGE_LOOP('',(#33469,#33471,#33472,#33473)); -#33475=FACE_OUTER_BOUND('',#33474,.F.); -#33477=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,8.106249928474E0)); -#33478=DIRECTION('',(-8.697579034767E-1,0.E0,-4.934786614838E-1)); -#33479=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#33480=AXIS2_PLACEMENT_3D('',#33477,#33478,#33479); -#33481=PLANE('',#33480); -#33482=ORIENTED_EDGE('',*,*,#25054,.F.); -#33484=ORIENTED_EDGE('',*,*,#33483,.T.); -#33485=ORIENTED_EDGE('',*,*,#28115,.T.); -#33486=ORIENTED_EDGE('',*,*,#33470,.F.); -#33487=EDGE_LOOP('',(#33482,#33484,#33485,#33486)); -#33488=FACE_OUTER_BOUND('',#33487,.F.); -#33490=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.03125E0)); -#33491=DIRECTION('',(-6.611559431073E-1,0.E0,-7.502485047595E-1)); -#33492=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#33493=AXIS2_PLACEMENT_3D('',#33490,#33491,#33492); -#33494=PLANE('',#33493); -#33495=ORIENTED_EDGE('',*,*,#25052,.F.); -#33497=ORIENTED_EDGE('',*,*,#33496,.T.); -#33498=ORIENTED_EDGE('',*,*,#28117,.T.); -#33499=ORIENTED_EDGE('',*,*,#33483,.F.); -#33500=EDGE_LOOP('',(#33495,#33497,#33498,#33499)); -#33501=FACE_OUTER_BOUND('',#33500,.F.); -#33503=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.012500071526E0)); -#33504=DIRECTION('',(-1.735739345657E-1,0.E0,-9.848208411886E-1)); -#33505=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#33506=AXIS2_PLACEMENT_3D('',#33503,#33504,#33505); -#33507=PLANE('',#33506); -#33508=ORIENTED_EDGE('',*,*,#25050,.F.); -#33510=ORIENTED_EDGE('',*,*,#33509,.T.); -#33511=ORIENTED_EDGE('',*,*,#28119,.T.); -#33512=ORIENTED_EDGE('',*,*,#33496,.F.); -#33513=EDGE_LOOP('',(#33508,#33510,#33511,#33512)); -#33514=FACE_OUTER_BOUND('',#33513,.F.); -#33516=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.125000071526E0)); -#33517=DIRECTION('',(1.E0,0.E0,0.E0)); -#33518=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33519=AXIS2_PLACEMENT_3D('',#33516,#33517,#33518); -#33520=PLANE('',#33519); -#33521=ORIENTED_EDGE('',*,*,#25048,.F.); -#33523=ORIENTED_EDGE('',*,*,#33522,.T.); -#33524=ORIENTED_EDGE('',*,*,#28121,.T.); -#33525=ORIENTED_EDGE('',*,*,#33509,.F.); -#33526=EDGE_LOOP('',(#33521,#33523,#33524,#33525)); -#33527=FACE_OUTER_BOUND('',#33526,.F.); -#33529=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.14375E0)); -#33530=DIRECTION('',(2.818404483901E-1,0.E0,9.594612872082E-1)); -#33531=DIRECTION('',(9.594612872082E-1,0.E0,-2.818404483901E-1)); -#33532=AXIS2_PLACEMENT_3D('',#33529,#33530,#33531); -#33533=PLANE('',#33532); -#33534=ORIENTED_EDGE('',*,*,#25046,.F.); -#33536=ORIENTED_EDGE('',*,*,#33535,.T.); -#33537=ORIENTED_EDGE('',*,*,#28123,.T.); -#33538=ORIENTED_EDGE('',*,*,#33522,.F.); -#33539=EDGE_LOOP('',(#33534,#33536,#33537,#33538)); -#33540=FACE_OUTER_BOUND('',#33539,.F.); -#33542=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.2E0)); -#33543=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#33544=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#33545=AXIS2_PLACEMENT_3D('',#33542,#33543,#33544); -#33546=PLANE('',#33545); -#33547=ORIENTED_EDGE('',*,*,#25044,.F.); -#33549=ORIENTED_EDGE('',*,*,#33548,.T.); -#33550=ORIENTED_EDGE('',*,*,#28125,.T.); -#33551=ORIENTED_EDGE('',*,*,#33535,.F.); -#33552=EDGE_LOOP('',(#33547,#33549,#33550,#33551)); -#33553=FACE_OUTER_BOUND('',#33552,.F.); -#33555=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.274999928474E0)); -#33556=DIRECTION('',(9.620371390182E-1,0.E0,2.729185650512E-1)); -#33557=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#33558=AXIS2_PLACEMENT_3D('',#33555,#33556,#33557); -#33559=PLANE('',#33558); -#33560=ORIENTED_EDGE('',*,*,#25042,.F.); -#33562=ORIENTED_EDGE('',*,*,#33561,.T.); -#33563=ORIENTED_EDGE('',*,*,#28127,.T.); -#33564=ORIENTED_EDGE('',*,*,#33548,.F.); -#33565=EDGE_LOOP('',(#33560,#33562,#33563,#33564)); -#33566=FACE_OUTER_BOUND('',#33565,.F.); -#33568=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,8.443749928474E0)); -#33569=DIRECTION('',(1.E0,0.E0,0.E0)); -#33570=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33571=AXIS2_PLACEMENT_3D('',#33568,#33569,#33570); -#33572=PLANE('',#33571); -#33573=ORIENTED_EDGE('',*,*,#25040,.F.); -#33575=ORIENTED_EDGE('',*,*,#33574,.T.); -#33576=ORIENTED_EDGE('',*,*,#28129,.T.); -#33577=ORIENTED_EDGE('',*,*,#33561,.F.); -#33578=EDGE_LOOP('',(#33573,#33575,#33576,#33577)); -#33579=FACE_OUTER_BOUND('',#33578,.F.); -#33581=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,8.518750071526E0)); -#33582=DIRECTION('',(9.620373440297E-1,0.E0,-2.729178423855E-1)); -#33583=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#33584=AXIS2_PLACEMENT_3D('',#33581,#33582,#33583); -#33585=PLANE('',#33584); -#33586=ORIENTED_EDGE('',*,*,#25038,.F.); -#33588=ORIENTED_EDGE('',*,*,#33587,.T.); -#33589=ORIENTED_EDGE('',*,*,#28131,.T.); -#33590=ORIENTED_EDGE('',*,*,#33574,.F.); -#33591=EDGE_LOOP('',(#33586,#33588,#33589,#33590)); -#33592=FACE_OUTER_BOUND('',#33591,.F.); -#33594=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,8.575000071526E0)); -#33595=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#33596=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#33597=AXIS2_PLACEMENT_3D('',#33594,#33595,#33596); -#33598=PLANE('',#33597); -#33599=ORIENTED_EDGE('',*,*,#25036,.F.); -#33601=ORIENTED_EDGE('',*,*,#33600,.T.); -#33602=ORIENTED_EDGE('',*,*,#28133,.T.); -#33603=ORIENTED_EDGE('',*,*,#33587,.F.); -#33604=EDGE_LOOP('',(#33599,#33601,#33602,#33603)); -#33605=FACE_OUTER_BOUND('',#33604,.F.); -#33607=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,8.612499928474E0)); -#33608=DIRECTION('',(5.065473053637E-1,0.E0,-8.622121707728E-1)); -#33609=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#33610=AXIS2_PLACEMENT_3D('',#33607,#33608,#33609); -#33611=PLANE('',#33610); -#33612=ORIENTED_EDGE('',*,*,#25034,.F.); -#33614=ORIENTED_EDGE('',*,*,#33613,.T.); -#33615=ORIENTED_EDGE('',*,*,#28135,.T.); -#33616=ORIENTED_EDGE('',*,*,#33600,.F.); -#33617=EDGE_LOOP('',(#33612,#33614,#33615,#33616)); -#33618=FACE_OUTER_BOUND('',#33617,.F.); -#33620=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,8.631250071526E0)); -#33621=DIRECTION('',(2.151544555851E-1,0.E0,-9.765800326864E-1)); -#33622=DIRECTION('',(-9.765800326864E-1,0.E0,-2.151544555851E-1)); -#33623=AXIS2_PLACEMENT_3D('',#33620,#33621,#33622); -#33624=PLANE('',#33623); -#33625=ORIENTED_EDGE('',*,*,#25032,.F.); -#33627=ORIENTED_EDGE('',*,*,#33626,.T.); -#33628=ORIENTED_EDGE('',*,*,#28137,.T.); -#33629=ORIENTED_EDGE('',*,*,#33613,.F.); -#33630=EDGE_LOOP('',(#33625,#33627,#33628,#33629)); -#33631=FACE_OUTER_BOUND('',#33630,.F.); -#33633=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,8.631250071526E0)); -#33634=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33635=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33636=AXIS2_PLACEMENT_3D('',#33633,#33634,#33635); -#33637=PLANE('',#33636); -#33638=ORIENTED_EDGE('',*,*,#25030,.F.); -#33640=ORIENTED_EDGE('',*,*,#33639,.T.); -#33641=ORIENTED_EDGE('',*,*,#28139,.T.); -#33642=ORIENTED_EDGE('',*,*,#33626,.F.); -#33643=EDGE_LOOP('',(#33638,#33640,#33641,#33642)); -#33644=FACE_OUTER_BOUND('',#33643,.F.); -#33646=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.612499928474E0)); -#33647=DIRECTION('',(-2.151544555851E-1,0.E0,-9.765800326864E-1)); -#33648=DIRECTION('',(-9.765800326864E-1,0.E0,2.151544555851E-1)); -#33649=AXIS2_PLACEMENT_3D('',#33646,#33647,#33648); -#33650=PLANE('',#33649); -#33651=ORIENTED_EDGE('',*,*,#25028,.F.); -#33653=ORIENTED_EDGE('',*,*,#33652,.T.); -#33654=ORIENTED_EDGE('',*,*,#28141,.T.); -#33655=ORIENTED_EDGE('',*,*,#33639,.F.); -#33656=EDGE_LOOP('',(#33651,#33653,#33654,#33655)); -#33657=FACE_OUTER_BOUND('',#33656,.F.); -#33659=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.575000071526E0)); -#33660=DIRECTION('',(-5.065476570090E-1,0.E0,-8.622119641820E-1)); -#33661=DIRECTION('',(-8.622119641820E-1,0.E0,5.065476570090E-1)); -#33662=AXIS2_PLACEMENT_3D('',#33659,#33660,#33661); -#33663=PLANE('',#33662); -#33664=ORIENTED_EDGE('',*,*,#25026,.F.); -#33666=ORIENTED_EDGE('',*,*,#33665,.T.); -#33667=ORIENTED_EDGE('',*,*,#28143,.T.); -#33668=ORIENTED_EDGE('',*,*,#33652,.F.); -#33669=EDGE_LOOP('',(#33664,#33666,#33667,#33668)); -#33670=FACE_OUTER_BOUND('',#33669,.F.); -#33672=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.518750071526E0)); -#33673=DIRECTION('',(-7.975043849272E-1,0.E0,-6.033131492201E-1)); -#33674=DIRECTION('',(-6.033131492201E-1,0.E0,7.975043849272E-1)); -#33675=AXIS2_PLACEMENT_3D('',#33672,#33673,#33674); -#33676=PLANE('',#33675); -#33677=ORIENTED_EDGE('',*,*,#25024,.F.); -#33679=ORIENTED_EDGE('',*,*,#33678,.T.); -#33680=ORIENTED_EDGE('',*,*,#28145,.T.); -#33681=ORIENTED_EDGE('',*,*,#33665,.F.); -#33682=EDGE_LOOP('',(#33677,#33679,#33680,#33681)); -#33683=FACE_OUTER_BOUND('',#33682,.F.); -#33685=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.443749928474E0)); -#33686=DIRECTION('',(-9.620373440297E-1,0.E0,-2.729178423855E-1)); -#33687=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#33688=AXIS2_PLACEMENT_3D('',#33685,#33686,#33687); -#33689=PLANE('',#33688); -#33690=ORIENTED_EDGE('',*,*,#25022,.F.); -#33692=ORIENTED_EDGE('',*,*,#33691,.T.); -#33693=ORIENTED_EDGE('',*,*,#28147,.T.); -#33694=ORIENTED_EDGE('',*,*,#33678,.F.); -#33695=EDGE_LOOP('',(#33690,#33692,#33693,#33694)); -#33696=FACE_OUTER_BOUND('',#33695,.F.); -#33698=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,8.274999928474E0)); -#33699=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33700=DIRECTION('',(0.E0,0.E0,1.E0)); -#33701=AXIS2_PLACEMENT_3D('',#33698,#33699,#33700); -#33702=PLANE('',#33701); -#33703=ORIENTED_EDGE('',*,*,#25020,.F.); -#33705=ORIENTED_EDGE('',*,*,#33704,.T.); -#33706=ORIENTED_EDGE('',*,*,#28149,.T.); -#33707=ORIENTED_EDGE('',*,*,#33691,.F.); -#33708=EDGE_LOOP('',(#33703,#33705,#33706,#33707)); -#33709=FACE_OUTER_BOUND('',#33708,.F.); -#33711=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,8.2E0)); -#33712=DIRECTION('',(-9.620371390182E-1,0.E0,2.729185650512E-1)); -#33713=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#33714=AXIS2_PLACEMENT_3D('',#33711,#33712,#33713); -#33715=PLANE('',#33714); -#33716=ORIENTED_EDGE('',*,*,#25018,.F.); -#33718=ORIENTED_EDGE('',*,*,#33717,.T.); -#33719=ORIENTED_EDGE('',*,*,#28151,.T.); -#33720=ORIENTED_EDGE('',*,*,#33704,.F.); -#33721=EDGE_LOOP('',(#33716,#33718,#33719,#33720)); -#33722=FACE_OUTER_BOUND('',#33721,.F.); -#33724=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,8.14375E0)); -#33725=DIRECTION('',(-7.975043849273E-1,0.E0,6.033131492200E-1)); -#33726=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#33727=AXIS2_PLACEMENT_3D('',#33724,#33725,#33726); -#33728=PLANE('',#33727); -#33729=ORIENTED_EDGE('',*,*,#25016,.F.); -#33731=ORIENTED_EDGE('',*,*,#33730,.T.); -#33732=ORIENTED_EDGE('',*,*,#28153,.T.); -#33733=ORIENTED_EDGE('',*,*,#33717,.F.); -#33734=EDGE_LOOP('',(#33729,#33731,#33732,#33733)); -#33735=FACE_OUTER_BOUND('',#33734,.F.); -#33737=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,8.125000071526E0)); -#33738=DIRECTION('',(-2.818406906687E-1,0.E0,9.594612160392E-1)); -#33739=DIRECTION('',(9.594612160392E-1,0.E0,2.818406906687E-1)); -#33740=AXIS2_PLACEMENT_3D('',#33737,#33738,#33739); -#33741=PLANE('',#33740); -#33742=ORIENTED_EDGE('',*,*,#25014,.F.); -#33743=ORIENTED_EDGE('',*,*,#33238,.T.); -#33744=ORIENTED_EDGE('',*,*,#28155,.T.); -#33745=ORIENTED_EDGE('',*,*,#33730,.F.); -#33746=EDGE_LOOP('',(#33742,#33743,#33744,#33745)); -#33747=FACE_OUTER_BOUND('',#33746,.F.); -#33749=CARTESIAN_POINT('',(4.E0,1.55E0,7.75E0)); -#33750=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33751=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33752=AXIS2_PLACEMENT_3D('',#33749,#33750,#33751); -#33753=PLANE('',#33752); -#33754=ORIENTED_EDGE('',*,*,#25094,.F.); -#33756=ORIENTED_EDGE('',*,*,#33755,.T.); -#33757=ORIENTED_EDGE('',*,*,#28172,.T.); -#33759=ORIENTED_EDGE('',*,*,#33758,.F.); -#33760=EDGE_LOOP('',(#33754,#33756,#33757,#33759)); -#33761=FACE_OUTER_BOUND('',#33760,.F.); -#33763=CARTESIAN_POINT('',(4.E0,1.55E0,7.8625E0)); -#33764=DIRECTION('',(1.E0,0.E0,0.E0)); -#33765=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33766=AXIS2_PLACEMENT_3D('',#33763,#33764,#33765); -#33767=PLANE('',#33766); -#33768=ORIENTED_EDGE('',*,*,#25100,.F.); -#33770=ORIENTED_EDGE('',*,*,#33769,.T.); -#33771=ORIENTED_EDGE('',*,*,#28174,.T.); -#33772=ORIENTED_EDGE('',*,*,#33755,.F.); -#33773=EDGE_LOOP('',(#33768,#33770,#33771,#33772)); -#33774=FACE_OUTER_BOUND('',#33773,.F.); -#33776=CARTESIAN_POINT('',(3.E0,1.55E0,7.8625E0)); -#33777=DIRECTION('',(0.E0,0.E0,1.E0)); -#33778=DIRECTION('',(1.E0,0.E0,0.E0)); -#33779=AXIS2_PLACEMENT_3D('',#33776,#33777,#33778); -#33780=PLANE('',#33779); -#33781=ORIENTED_EDGE('',*,*,#25098,.F.); -#33783=ORIENTED_EDGE('',*,*,#33782,.T.); -#33784=ORIENTED_EDGE('',*,*,#28176,.T.); -#33785=ORIENTED_EDGE('',*,*,#33769,.F.); -#33786=EDGE_LOOP('',(#33781,#33783,#33784,#33785)); -#33787=FACE_OUTER_BOUND('',#33786,.F.); -#33789=CARTESIAN_POINT('',(3.E0,1.55E0,7.75E0)); -#33790=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33791=DIRECTION('',(0.E0,0.E0,1.E0)); -#33792=AXIS2_PLACEMENT_3D('',#33789,#33790,#33791); -#33793=PLANE('',#33792); -#33794=ORIENTED_EDGE('',*,*,#25096,.F.); -#33795=ORIENTED_EDGE('',*,*,#33758,.T.); -#33796=ORIENTED_EDGE('',*,*,#28178,.T.); -#33797=ORIENTED_EDGE('',*,*,#33782,.F.); -#33798=EDGE_LOOP('',(#33794,#33795,#33796,#33797)); -#33799=FACE_OUTER_BOUND('',#33798,.F.); -#33801=CARTESIAN_POINT('',(3.E0,1.55E0,7.149999928474E0)); -#33802=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33803=DIRECTION('',(0.E0,0.E0,1.E0)); -#33804=AXIS2_PLACEMENT_3D('',#33801,#33802,#33803); -#33805=PLANE('',#33804); -#33806=ORIENTED_EDGE('',*,*,#25104,.F.); -#33808=ORIENTED_EDGE('',*,*,#33807,.T.); -#33809=ORIENTED_EDGE('',*,*,#28195,.T.); -#33811=ORIENTED_EDGE('',*,*,#33810,.F.); -#33812=EDGE_LOOP('',(#33806,#33808,#33809,#33811)); -#33813=FACE_OUTER_BOUND('',#33812,.F.); -#33815=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,7.056250071526E0)); -#33816=DIRECTION('',(-9.752006830246E-1,0.E0,-2.213224521559E-1)); -#33817=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#33818=AXIS2_PLACEMENT_3D('',#33815,#33816,#33817); -#33819=PLANE('',#33818); -#33820=ORIENTED_EDGE('',*,*,#25130,.F.); -#33822=ORIENTED_EDGE('',*,*,#33821,.T.); -#33823=ORIENTED_EDGE('',*,*,#28197,.T.); -#33824=ORIENTED_EDGE('',*,*,#33807,.F.); -#33825=EDGE_LOOP('',(#33820,#33822,#33823,#33824)); -#33826=FACE_OUTER_BOUND('',#33825,.F.); -#33828=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,6.981249928474E0)); -#33829=DIRECTION('',(-8.697579034767E-1,0.E0,-4.934786614838E-1)); -#33830=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#33831=AXIS2_PLACEMENT_3D('',#33828,#33829,#33830); -#33832=PLANE('',#33831); -#33833=ORIENTED_EDGE('',*,*,#25128,.F.); -#33835=ORIENTED_EDGE('',*,*,#33834,.T.); -#33836=ORIENTED_EDGE('',*,*,#28199,.T.); -#33837=ORIENTED_EDGE('',*,*,#33821,.F.); -#33838=EDGE_LOOP('',(#33833,#33835,#33836,#33837)); -#33839=FACE_OUTER_BOUND('',#33838,.F.); -#33841=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,6.90625E0)); -#33842=DIRECTION('',(-6.611559431073E-1,0.E0,-7.502485047595E-1)); -#33843=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#33844=AXIS2_PLACEMENT_3D('',#33841,#33842,#33843); -#33845=PLANE('',#33844); -#33846=ORIENTED_EDGE('',*,*,#25126,.F.); -#33848=ORIENTED_EDGE('',*,*,#33847,.T.); -#33849=ORIENTED_EDGE('',*,*,#28201,.T.); -#33850=ORIENTED_EDGE('',*,*,#33834,.F.); -#33851=EDGE_LOOP('',(#33846,#33848,#33849,#33850)); -#33852=FACE_OUTER_BOUND('',#33851,.F.); -#33854=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,6.868749928474E0)); -#33855=DIRECTION('',(-4.032184156573E-1,0.E0,-9.151037696758E-1)); -#33856=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#33857=AXIS2_PLACEMENT_3D('',#33854,#33855,#33856); -#33858=PLANE('',#33857); -#33859=ORIENTED_EDGE('',*,*,#25124,.F.); -#33861=ORIENTED_EDGE('',*,*,#33860,.T.); -#33862=ORIENTED_EDGE('',*,*,#28203,.T.); -#33863=ORIENTED_EDGE('',*,*,#33847,.F.); -#33864=EDGE_LOOP('',(#33859,#33861,#33862,#33863)); -#33865=FACE_OUTER_BOUND('',#33864,.F.); -#33867=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.85E0)); -#33868=DIRECTION('',(-1.735739345656E-1,0.E0,-9.848208411886E-1)); -#33869=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345656E-1)); -#33870=AXIS2_PLACEMENT_3D('',#33867,#33868,#33869); -#33871=PLANE('',#33870); -#33872=ORIENTED_EDGE('',*,*,#25122,.F.); -#33874=ORIENTED_EDGE('',*,*,#33873,.T.); -#33875=ORIENTED_EDGE('',*,*,#28205,.T.); -#33876=ORIENTED_EDGE('',*,*,#33860,.F.); -#33877=EDGE_LOOP('',(#33872,#33874,#33875,#33876)); -#33878=FACE_OUTER_BOUND('',#33877,.F.); -#33880=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.85E0)); -#33881=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33882=DIRECTION('',(-1.E0,0.E0,0.E0)); -#33883=AXIS2_PLACEMENT_3D('',#33880,#33881,#33882); -#33884=PLANE('',#33883); -#33885=ORIENTED_EDGE('',*,*,#25120,.F.); -#33887=ORIENTED_EDGE('',*,*,#33886,.T.); -#33888=ORIENTED_EDGE('',*,*,#28207,.T.); -#33889=ORIENTED_EDGE('',*,*,#33873,.F.); -#33890=EDGE_LOOP('',(#33885,#33887,#33888,#33889)); -#33891=FACE_OUTER_BOUND('',#33890,.F.); -#33893=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,6.868749928474E0)); -#33894=DIRECTION('',(1.735740288863E-1,0.E0,-9.848208245646E-1)); -#33895=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#33896=AXIS2_PLACEMENT_3D('',#33893,#33894,#33895); -#33897=PLANE('',#33896); -#33898=ORIENTED_EDGE('',*,*,#25118,.F.); -#33900=ORIENTED_EDGE('',*,*,#33899,.T.); -#33901=ORIENTED_EDGE('',*,*,#28209,.T.); -#33902=ORIENTED_EDGE('',*,*,#33886,.F.); -#33903=EDGE_LOOP('',(#33898,#33900,#33901,#33902)); -#33904=FACE_OUTER_BOUND('',#33903,.F.); -#33906=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.90625E0)); -#33907=DIRECTION('',(4.032183565367E-1,0.E0,-9.151037957259E-1)); -#33908=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#33909=AXIS2_PLACEMENT_3D('',#33906,#33907,#33908); -#33910=PLANE('',#33909); -#33911=ORIENTED_EDGE('',*,*,#25116,.F.); -#33913=ORIENTED_EDGE('',*,*,#33912,.T.); -#33914=ORIENTED_EDGE('',*,*,#28211,.T.); -#33915=ORIENTED_EDGE('',*,*,#33899,.F.); -#33916=EDGE_LOOP('',(#33911,#33913,#33914,#33915)); -#33917=FACE_OUTER_BOUND('',#33916,.F.); -#33919=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,6.981249928474E0)); -#33920=DIRECTION('',(6.611559105280E-1,0.E0,-7.502485334700E-1)); -#33921=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#33922=AXIS2_PLACEMENT_3D('',#33919,#33920,#33921); -#33923=PLANE('',#33922); -#33924=ORIENTED_EDGE('',*,*,#25114,.F.); -#33926=ORIENTED_EDGE('',*,*,#33925,.T.); -#33927=ORIENTED_EDGE('',*,*,#28213,.T.); -#33928=ORIENTED_EDGE('',*,*,#33912,.F.); -#33929=EDGE_LOOP('',(#33924,#33926,#33927,#33928)); -#33930=FACE_OUTER_BOUND('',#33929,.F.); -#33932=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,7.056250071526E0)); -#33933=DIRECTION('',(8.697578756632E-1,0.E0,-4.934787105051E-1)); -#33934=DIRECTION('',(-4.934787105051E-1,0.E0,-8.697578756632E-1)); -#33935=AXIS2_PLACEMENT_3D('',#33932,#33933,#33934); -#33936=PLANE('',#33935); -#33937=ORIENTED_EDGE('',*,*,#25112,.F.); -#33939=ORIENTED_EDGE('',*,*,#33938,.T.); -#33940=ORIENTED_EDGE('',*,*,#28215,.T.); -#33941=ORIENTED_EDGE('',*,*,#33925,.F.); -#33942=EDGE_LOOP('',(#33937,#33939,#33940,#33941)); -#33943=FACE_OUTER_BOUND('',#33942,.F.); -#33945=CARTESIAN_POINT('',(4.E0,1.55E0,7.149999928474E0)); -#33946=DIRECTION('',(9.752006788427E-1,0.E0,-2.213224705823E-1)); -#33947=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#33948=AXIS2_PLACEMENT_3D('',#33945,#33946,#33947); -#33949=PLANE('',#33948); -#33950=ORIENTED_EDGE('',*,*,#25110,.F.); -#33952=ORIENTED_EDGE('',*,*,#33951,.T.); -#33953=ORIENTED_EDGE('',*,*,#28217,.T.); -#33954=ORIENTED_EDGE('',*,*,#33938,.F.); -#33955=EDGE_LOOP('',(#33950,#33952,#33953,#33954)); -#33956=FACE_OUTER_BOUND('',#33955,.F.); -#33958=CARTESIAN_POINT('',(4.E0,1.55E0,7.599999928474E0)); -#33959=DIRECTION('',(1.E0,0.E0,0.E0)); -#33960=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33961=AXIS2_PLACEMENT_3D('',#33958,#33959,#33960); -#33962=PLANE('',#33961); -#33963=ORIENTED_EDGE('',*,*,#25108,.F.); -#33965=ORIENTED_EDGE('',*,*,#33964,.T.); -#33966=ORIENTED_EDGE('',*,*,#28219,.T.); -#33967=ORIENTED_EDGE('',*,*,#33951,.F.); -#33968=EDGE_LOOP('',(#33963,#33965,#33966,#33967)); -#33969=FACE_OUTER_BOUND('',#33968,.F.); -#33971=CARTESIAN_POINT('',(3.E0,1.55E0,7.599999928474E0)); -#33972=DIRECTION('',(0.E0,0.E0,1.E0)); -#33973=DIRECTION('',(1.E0,0.E0,0.E0)); -#33974=AXIS2_PLACEMENT_3D('',#33971,#33972,#33973); -#33975=PLANE('',#33974); -#33976=ORIENTED_EDGE('',*,*,#25106,.F.); -#33977=ORIENTED_EDGE('',*,*,#33810,.T.); -#33978=ORIENTED_EDGE('',*,*,#28221,.T.); -#33979=ORIENTED_EDGE('',*,*,#33964,.F.); -#33980=EDGE_LOOP('',(#33976,#33977,#33978,#33979)); -#33981=FACE_OUTER_BOUND('',#33980,.F.); -#33983=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.487499928474E0)); -#33984=DIRECTION('',(1.E0,0.E0,0.E0)); -#33985=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33986=AXIS2_PLACEMENT_3D('',#33983,#33984,#33985); -#33987=PLANE('',#33986); -#33988=ORIENTED_EDGE('',*,*,#26470,.F.); -#33990=ORIENTED_EDGE('',*,*,#33989,.T.); -#33991=ORIENTED_EDGE('',*,*,#28225,.T.); -#33993=ORIENTED_EDGE('',*,*,#33992,.F.); -#33994=EDGE_LOOP('',(#33988,#33990,#33991,#33993)); -#33995=FACE_OUTER_BOUND('',#33994,.F.); -#33997=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.487499928474E0)); -#33998=DIRECTION('',(0.E0,0.E0,-1.E0)); -#33999=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34000=AXIS2_PLACEMENT_3D('',#33997,#33998,#33999); -#34001=PLANE('',#34000); -#34002=ORIENTED_EDGE('',*,*,#26492,.F.); -#34004=ORIENTED_EDGE('',*,*,#34003,.T.); -#34005=ORIENTED_EDGE('',*,*,#28227,.T.); -#34006=ORIENTED_EDGE('',*,*,#33989,.F.); -#34007=EDGE_LOOP('',(#34002,#34004,#34005,#34006)); -#34008=FACE_OUTER_BOUND('',#34007,.F.); -#34010=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,7.149999928474E0)); -#34011=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34012=DIRECTION('',(0.E0,0.E0,1.E0)); -#34013=AXIS2_PLACEMENT_3D('',#34010,#34011,#34012); -#34014=PLANE('',#34013); -#34015=ORIENTED_EDGE('',*,*,#26490,.F.); -#34017=ORIENTED_EDGE('',*,*,#34016,.T.); -#34018=ORIENTED_EDGE('',*,*,#28229,.T.); -#34019=ORIENTED_EDGE('',*,*,#34003,.F.); -#34020=EDGE_LOOP('',(#34015,#34017,#34018,#34019)); -#34021=FACE_OUTER_BOUND('',#34020,.F.); -#34023=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,7.075E0)); -#34024=DIRECTION('',(-9.620371390182E-1,0.E0,2.729185650512E-1)); -#34025=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#34026=AXIS2_PLACEMENT_3D('',#34023,#34024,#34025); -#34027=PLANE('',#34026); -#34028=ORIENTED_EDGE('',*,*,#26488,.F.); -#34030=ORIENTED_EDGE('',*,*,#34029,.T.); -#34031=ORIENTED_EDGE('',*,*,#28231,.T.); -#34032=ORIENTED_EDGE('',*,*,#34016,.F.); -#34033=EDGE_LOOP('',(#34028,#34030,#34031,#34032)); -#34034=FACE_OUTER_BOUND('',#34033,.F.); -#34036=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,7.01875E0)); -#34037=DIRECTION('',(-7.975043849273E-1,0.E0,6.033131492200E-1)); -#34038=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#34039=AXIS2_PLACEMENT_3D('',#34036,#34037,#34038); -#34040=PLANE('',#34039); -#34041=ORIENTED_EDGE('',*,*,#26486,.F.); -#34043=ORIENTED_EDGE('',*,*,#34042,.T.); -#34044=ORIENTED_EDGE('',*,*,#28233,.T.); -#34045=ORIENTED_EDGE('',*,*,#34029,.F.); -#34046=EDGE_LOOP('',(#34041,#34043,#34044,#34045)); -#34047=FACE_OUTER_BOUND('',#34046,.F.); -#34049=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,6.981249928474E0)); -#34050=DIRECTION('',(-5.065498117766E-1,0.E0,8.622106982571E-1)); -#34051=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117766E-1)); -#34052=AXIS2_PLACEMENT_3D('',#34049,#34050,#34051); -#34053=PLANE('',#34052); -#34054=ORIENTED_EDGE('',*,*,#26484,.F.); -#34056=ORIENTED_EDGE('',*,*,#34055,.T.); -#34057=ORIENTED_EDGE('',*,*,#28235,.T.); -#34058=ORIENTED_EDGE('',*,*,#34042,.F.); -#34059=EDGE_LOOP('',(#34054,#34056,#34057,#34058)); -#34060=FACE_OUTER_BOUND('',#34059,.F.); -#34062=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,6.9625E0)); -#34063=DIRECTION('',(-2.151521073348E-1,0.E0,9.765805500364E-1)); -#34064=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#34065=AXIS2_PLACEMENT_3D('',#34062,#34063,#34064); -#34066=PLANE('',#34065); -#34067=ORIENTED_EDGE('',*,*,#26482,.F.); -#34069=ORIENTED_EDGE('',*,*,#34068,.T.); -#34070=ORIENTED_EDGE('',*,*,#28237,.T.); -#34071=ORIENTED_EDGE('',*,*,#34055,.F.); -#34072=EDGE_LOOP('',(#34067,#34069,#34070,#34071)); -#34073=FACE_OUTER_BOUND('',#34072,.F.); -#34075=CARTESIAN_POINT('',(3.340425550938E0,1.55E0,6.9625E0)); -#34076=DIRECTION('',(0.E0,0.E0,1.E0)); -#34077=DIRECTION('',(1.E0,0.E0,0.E0)); -#34078=AXIS2_PLACEMENT_3D('',#34075,#34076,#34077); -#34079=PLANE('',#34078); -#34080=ORIENTED_EDGE('',*,*,#26480,.F.); -#34082=ORIENTED_EDGE('',*,*,#34081,.T.); -#34083=ORIENTED_EDGE('',*,*,#28239,.T.); -#34084=ORIENTED_EDGE('',*,*,#34068,.F.); -#34085=EDGE_LOOP('',(#34080,#34082,#34083,#34084)); -#34086=FACE_OUTER_BOUND('',#34085,.F.); -#34088=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,6.981249928474E0)); -#34089=DIRECTION('',(2.151521073348E-1,0.E0,9.765805500364E-1)); -#34090=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#34091=AXIS2_PLACEMENT_3D('',#34088,#34089,#34090); -#34092=PLANE('',#34091); -#34093=ORIENTED_EDGE('',*,*,#26478,.F.); -#34095=ORIENTED_EDGE('',*,*,#34094,.T.); -#34096=ORIENTED_EDGE('',*,*,#28241,.T.); -#34097=ORIENTED_EDGE('',*,*,#34081,.F.); -#34098=EDGE_LOOP('',(#34093,#34095,#34096,#34097)); -#34099=FACE_OUTER_BOUND('',#34098,.F.); -#34101=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,7.01875E0)); -#34102=DIRECTION('',(5.065494601308E-1,0.E0,8.622109048494E-1)); -#34103=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#34104=AXIS2_PLACEMENT_3D('',#34101,#34102,#34103); -#34105=PLANE('',#34104); -#34106=ORIENTED_EDGE('',*,*,#26476,.F.); -#34108=ORIENTED_EDGE('',*,*,#34107,.T.); -#34109=ORIENTED_EDGE('',*,*,#28243,.T.); -#34110=ORIENTED_EDGE('',*,*,#34094,.F.); -#34111=EDGE_LOOP('',(#34106,#34108,#34109,#34110)); -#34112=FACE_OUTER_BOUND('',#34111,.F.); -#34114=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,7.075E0)); -#34115=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#34116=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#34117=AXIS2_PLACEMENT_3D('',#34114,#34115,#34116); -#34118=PLANE('',#34117); -#34119=ORIENTED_EDGE('',*,*,#26474,.F.); -#34121=ORIENTED_EDGE('',*,*,#34120,.T.); -#34122=ORIENTED_EDGE('',*,*,#28245,.T.); -#34123=ORIENTED_EDGE('',*,*,#34107,.F.); -#34124=EDGE_LOOP('',(#34119,#34121,#34122,#34123)); -#34125=FACE_OUTER_BOUND('',#34124,.F.); -#34127=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,7.149999928474E0)); -#34128=DIRECTION('',(9.620371390182E-1,0.E0,2.729185650512E-1)); -#34129=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#34130=AXIS2_PLACEMENT_3D('',#34127,#34128,#34129); -#34131=PLANE('',#34130); -#34132=ORIENTED_EDGE('',*,*,#26472,.F.); -#34133=ORIENTED_EDGE('',*,*,#33992,.T.); -#34134=ORIENTED_EDGE('',*,*,#28247,.T.); -#34135=ORIENTED_EDGE('',*,*,#34120,.F.); -#34136=EDGE_LOOP('',(#34132,#34133,#34134,#34135)); -#34137=FACE_OUTER_BOUND('',#34136,.F.); -#34139=CARTESIAN_POINT('',(4.E0,1.55E0,6.606249856949E0)); -#34140=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34141=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34142=AXIS2_PLACEMENT_3D('',#34139,#34140,#34141); -#34143=PLANE('',#34142); -#34144=ORIENTED_EDGE('',*,*,#25134,.F.); -#34146=ORIENTED_EDGE('',*,*,#34145,.T.); -#34147=ORIENTED_EDGE('',*,*,#28264,.T.); -#34149=ORIENTED_EDGE('',*,*,#34148,.F.); -#34150=EDGE_LOOP('',(#34144,#34146,#34147,#34149)); -#34151=FACE_OUTER_BOUND('',#34150,.F.); -#34153=CARTESIAN_POINT('',(4.E0,1.55E0,6.700000143051E0)); -#34154=DIRECTION('',(1.E0,0.E0,0.E0)); -#34155=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34156=AXIS2_PLACEMENT_3D('',#34153,#34154,#34155); -#34157=PLANE('',#34156); -#34158=ORIENTED_EDGE('',*,*,#25140,.F.); -#34160=ORIENTED_EDGE('',*,*,#34159,.T.); -#34161=ORIENTED_EDGE('',*,*,#28266,.T.); -#34162=ORIENTED_EDGE('',*,*,#34145,.F.); -#34163=EDGE_LOOP('',(#34158,#34160,#34161,#34162)); -#34164=FACE_OUTER_BOUND('',#34163,.F.); -#34166=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.700000143051E0)); -#34167=DIRECTION('',(0.E0,0.E0,1.E0)); -#34168=DIRECTION('',(1.E0,0.E0,0.E0)); -#34169=AXIS2_PLACEMENT_3D('',#34166,#34167,#34168); -#34170=PLANE('',#34169); -#34171=ORIENTED_EDGE('',*,*,#25138,.F.); -#34173=ORIENTED_EDGE('',*,*,#34172,.T.); -#34174=ORIENTED_EDGE('',*,*,#28268,.T.); -#34175=ORIENTED_EDGE('',*,*,#34159,.F.); -#34176=EDGE_LOOP('',(#34171,#34173,#34174,#34175)); -#34177=FACE_OUTER_BOUND('',#34176,.F.); -#34179=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,6.606249856949E0)); -#34180=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34181=DIRECTION('',(0.E0,0.E0,1.E0)); -#34182=AXIS2_PLACEMENT_3D('',#34179,#34180,#34181); -#34183=PLANE('',#34182); -#34184=ORIENTED_EDGE('',*,*,#25136,.F.); -#34185=ORIENTED_EDGE('',*,*,#34148,.T.); -#34186=ORIENTED_EDGE('',*,*,#28270,.T.); -#34187=ORIENTED_EDGE('',*,*,#34172,.F.); -#34188=EDGE_LOOP('',(#34184,#34185,#34186,#34187)); -#34189=FACE_OUTER_BOUND('',#34188,.F.); -#34191=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.606249856949E0)); -#34192=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34193=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34194=AXIS2_PLACEMENT_3D('',#34191,#34192,#34193); -#34195=PLANE('',#34194); -#34196=ORIENTED_EDGE('',*,*,#25144,.F.); -#34198=ORIENTED_EDGE('',*,*,#34197,.T.); -#34199=ORIENTED_EDGE('',*,*,#28287,.T.); -#34201=ORIENTED_EDGE('',*,*,#34200,.F.); -#34202=EDGE_LOOP('',(#34196,#34198,#34199,#34201)); -#34203=FACE_OUTER_BOUND('',#34202,.F.); -#34205=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.700000143051E0)); -#34206=DIRECTION('',(1.E0,0.E0,0.E0)); -#34207=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34208=AXIS2_PLACEMENT_3D('',#34205,#34206,#34207); -#34209=PLANE('',#34208); -#34210=ORIENTED_EDGE('',*,*,#25150,.F.); -#34212=ORIENTED_EDGE('',*,*,#34211,.T.); -#34213=ORIENTED_EDGE('',*,*,#28289,.T.); -#34214=ORIENTED_EDGE('',*,*,#34197,.F.); -#34215=EDGE_LOOP('',(#34210,#34212,#34213,#34214)); -#34216=FACE_OUTER_BOUND('',#34215,.F.); -#34218=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.700000143051E0)); -#34219=DIRECTION('',(0.E0,0.E0,1.E0)); -#34220=DIRECTION('',(1.E0,0.E0,0.E0)); -#34221=AXIS2_PLACEMENT_3D('',#34218,#34219,#34220); -#34222=PLANE('',#34221); -#34223=ORIENTED_EDGE('',*,*,#25148,.F.); -#34225=ORIENTED_EDGE('',*,*,#34224,.T.); -#34226=ORIENTED_EDGE('',*,*,#28291,.T.); -#34227=ORIENTED_EDGE('',*,*,#34211,.F.); -#34228=EDGE_LOOP('',(#34223,#34225,#34226,#34227)); -#34229=FACE_OUTER_BOUND('',#34228,.F.); -#34231=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,6.606249856949E0)); -#34232=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34233=DIRECTION('',(0.E0,0.E0,1.E0)); -#34234=AXIS2_PLACEMENT_3D('',#34231,#34232,#34233); -#34235=PLANE('',#34234); -#34236=ORIENTED_EDGE('',*,*,#25146,.F.); -#34237=ORIENTED_EDGE('',*,*,#34200,.T.); -#34238=ORIENTED_EDGE('',*,*,#28293,.T.); -#34239=ORIENTED_EDGE('',*,*,#34224,.F.); -#34240=EDGE_LOOP('',(#34236,#34237,#34238,#34239)); -#34241=FACE_OUTER_BOUND('',#34240,.F.); -#34243=CARTESIAN_POINT('',(4.E0,1.55E0,5.818749856949E0)); -#34244=DIRECTION('',(1.E0,0.E0,0.E0)); -#34245=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34246=AXIS2_PLACEMENT_3D('',#34243,#34244,#34245); -#34247=PLANE('',#34246); -#34248=ORIENTED_EDGE('',*,*,#25154,.F.); -#34250=ORIENTED_EDGE('',*,*,#34249,.T.); -#34251=ORIENTED_EDGE('',*,*,#28310,.T.); -#34253=ORIENTED_EDGE('',*,*,#34252,.F.); -#34254=EDGE_LOOP('',(#34248,#34250,#34251,#34253)); -#34255=FACE_OUTER_BOUND('',#34254,.F.); -#34257=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.081250143051E0)); -#34258=DIRECTION('',(5.446008090273E-1,0.E0,8.386953909536E-1)); -#34259=DIRECTION('',(8.386953909536E-1,0.E0,-5.446008090273E-1)); -#34260=AXIS2_PLACEMENT_3D('',#34257,#34258,#34259); -#34261=PLANE('',#34260); -#34262=ORIENTED_EDGE('',*,*,#25176,.F.); -#34264=ORIENTED_EDGE('',*,*,#34263,.T.); -#34265=ORIENTED_EDGE('',*,*,#28312,.T.); -#34266=ORIENTED_EDGE('',*,*,#34249,.F.); -#34267=EDGE_LOOP('',(#34262,#34264,#34265,#34266)); -#34268=FACE_OUTER_BOUND('',#34267,.F.); -#34270=CARTESIAN_POINT('',(4.E0,1.55E0,6.34375E0)); -#34271=DIRECTION('',(5.446001827453E-1,0.E0,-8.386957976250E-1)); -#34272=DIRECTION('',(-8.386957976250E-1,0.E0,-5.446001827453E-1)); -#34273=AXIS2_PLACEMENT_3D('',#34270,#34271,#34272); -#34274=PLANE('',#34273); -#34275=ORIENTED_EDGE('',*,*,#25174,.F.); -#34277=ORIENTED_EDGE('',*,*,#34276,.T.); -#34278=ORIENTED_EDGE('',*,*,#28314,.T.); -#34279=ORIENTED_EDGE('',*,*,#34263,.F.); -#34280=EDGE_LOOP('',(#34275,#34277,#34278,#34279)); -#34281=FACE_OUTER_BOUND('',#34280,.F.); -#34283=CARTESIAN_POINT('',(4.E0,1.55E0,6.45625E0)); -#34284=DIRECTION('',(1.E0,0.E0,0.E0)); -#34285=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34286=AXIS2_PLACEMENT_3D('',#34283,#34284,#34285); -#34287=PLANE('',#34286); -#34288=ORIENTED_EDGE('',*,*,#25172,.F.); -#34290=ORIENTED_EDGE('',*,*,#34289,.T.); -#34291=ORIENTED_EDGE('',*,*,#28316,.T.); -#34292=ORIENTED_EDGE('',*,*,#34276,.F.); -#34293=EDGE_LOOP('',(#34288,#34290,#34291,#34292)); -#34294=FACE_OUTER_BOUND('',#34293,.F.); -#34296=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.137500143051E0)); -#34297=DIRECTION('',(-5.295221154414E-1,0.E0,8.482961329975E-1)); -#34298=DIRECTION('',(8.482961329975E-1,0.E0,5.295221154414E-1)); -#34299=AXIS2_PLACEMENT_3D('',#34296,#34297,#34298); -#34300=PLANE('',#34299); -#34301=ORIENTED_EDGE('',*,*,#25170,.F.); -#34303=ORIENTED_EDGE('',*,*,#34302,.T.); -#34304=ORIENTED_EDGE('',*,*,#28318,.T.); -#34305=ORIENTED_EDGE('',*,*,#34289,.F.); -#34306=EDGE_LOOP('',(#34301,#34303,#34304,#34305)); -#34307=FACE_OUTER_BOUND('',#34306,.F.); -#34309=CARTESIAN_POINT('',(3.E0,1.55E0,6.45625E0)); -#34310=DIRECTION('',(5.457882684251E-1,0.E0,8.379231265752E-1)); -#34311=DIRECTION('',(8.379231265752E-1,0.E0,-5.457882684251E-1)); -#34312=AXIS2_PLACEMENT_3D('',#34309,#34310,#34311); -#34313=PLANE('',#34312); -#34314=ORIENTED_EDGE('',*,*,#25168,.F.); -#34316=ORIENTED_EDGE('',*,*,#34315,.T.); -#34317=ORIENTED_EDGE('',*,*,#28320,.T.); -#34318=ORIENTED_EDGE('',*,*,#34302,.F.); -#34319=EDGE_LOOP('',(#34314,#34316,#34317,#34318)); -#34320=FACE_OUTER_BOUND('',#34319,.F.); -#34322=CARTESIAN_POINT('',(3.E0,1.55E0,6.34375E0)); -#34323=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34324=DIRECTION('',(0.E0,0.E0,1.E0)); -#34325=AXIS2_PLACEMENT_3D('',#34322,#34323,#34324); -#34326=PLANE('',#34325); -#34327=ORIENTED_EDGE('',*,*,#25166,.F.); -#34329=ORIENTED_EDGE('',*,*,#34328,.T.); -#34330=ORIENTED_EDGE('',*,*,#28322,.T.); -#34331=ORIENTED_EDGE('',*,*,#34315,.F.); -#34332=EDGE_LOOP('',(#34327,#34329,#34330,#34331)); -#34333=FACE_OUTER_BOUND('',#34332,.F.); -#34335=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.081250143051E0)); -#34336=DIRECTION('',(-5.446001827453E-1,0.E0,-8.386957976250E-1)); -#34337=DIRECTION('',(-8.386957976250E-1,0.E0,5.446001827453E-1)); -#34338=AXIS2_PLACEMENT_3D('',#34335,#34336,#34337); -#34339=PLANE('',#34338); -#34340=ORIENTED_EDGE('',*,*,#25164,.F.); -#34342=ORIENTED_EDGE('',*,*,#34341,.T.); -#34343=ORIENTED_EDGE('',*,*,#28324,.T.); -#34344=ORIENTED_EDGE('',*,*,#34328,.F.); -#34345=EDGE_LOOP('',(#34340,#34342,#34343,#34344)); -#34346=FACE_OUTER_BOUND('',#34345,.F.); -#34348=CARTESIAN_POINT('',(3.E0,1.55E0,5.818749856949E0)); -#34349=DIRECTION('',(-5.446008090273E-1,0.E0,8.386953909536E-1)); -#34350=DIRECTION('',(8.386953909536E-1,0.E0,5.446008090273E-1)); -#34351=AXIS2_PLACEMENT_3D('',#34348,#34349,#34350); -#34352=PLANE('',#34351); -#34353=ORIENTED_EDGE('',*,*,#25162,.F.); -#34355=ORIENTED_EDGE('',*,*,#34354,.T.); -#34356=ORIENTED_EDGE('',*,*,#28326,.T.); -#34357=ORIENTED_EDGE('',*,*,#34341,.F.); -#34358=EDGE_LOOP('',(#34353,#34355,#34356,#34357)); -#34359=FACE_OUTER_BOUND('',#34358,.F.); -#34361=CARTESIAN_POINT('',(3.E0,1.55E0,5.706249856949E0)); -#34362=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34363=DIRECTION('',(0.E0,0.E0,1.E0)); -#34364=AXIS2_PLACEMENT_3D('',#34361,#34362,#34363); -#34365=PLANE('',#34364); -#34366=ORIENTED_EDGE('',*,*,#25160,.F.); -#34368=ORIENTED_EDGE('',*,*,#34367,.T.); -#34369=ORIENTED_EDGE('',*,*,#28328,.T.); -#34370=ORIENTED_EDGE('',*,*,#34354,.F.); -#34371=EDGE_LOOP('',(#34366,#34368,#34369,#34370)); -#34372=FACE_OUTER_BOUND('',#34371,.F.); -#34374=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.025000143051E0)); -#34375=DIRECTION('',(5.457887843600E-1,0.E0,-8.379227905164E-1)); -#34376=DIRECTION('',(-8.379227905164E-1,0.E0,-5.457887843600E-1)); -#34377=AXIS2_PLACEMENT_3D('',#34374,#34375,#34376); -#34378=PLANE('',#34377); -#34379=ORIENTED_EDGE('',*,*,#25158,.F.); -#34381=ORIENTED_EDGE('',*,*,#34380,.T.); -#34382=ORIENTED_EDGE('',*,*,#28330,.T.); -#34383=ORIENTED_EDGE('',*,*,#34367,.F.); -#34384=EDGE_LOOP('',(#34379,#34381,#34382,#34383)); -#34385=FACE_OUTER_BOUND('',#34384,.F.); -#34387=CARTESIAN_POINT('',(4.E0,1.55E0,5.706249856949E0)); -#34388=DIRECTION('',(-5.295226284698E-1,0.E0,-8.482958127554E-1)); -#34389=DIRECTION('',(-8.482958127554E-1,0.E0,5.295226284698E-1)); -#34390=AXIS2_PLACEMENT_3D('',#34387,#34388,#34389); -#34391=PLANE('',#34390); -#34392=ORIENTED_EDGE('',*,*,#25156,.F.); -#34393=ORIENTED_EDGE('',*,*,#34252,.T.); -#34394=ORIENTED_EDGE('',*,*,#28332,.T.); -#34395=ORIENTED_EDGE('',*,*,#34380,.F.); -#34396=EDGE_LOOP('',(#34392,#34393,#34394,#34395)); -#34397=FACE_OUTER_BOUND('',#34396,.F.); -#34399=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.406250143051E0)); -#34400=DIRECTION('',(-8.697566915162E-1,0.E0,4.934807975625E-1)); -#34401=DIRECTION('',(4.934807975625E-1,0.E0,8.697566915162E-1)); -#34402=AXIS2_PLACEMENT_3D('',#34399,#34400,#34401); -#34403=PLANE('',#34402); -#34404=ORIENTED_EDGE('',*,*,#25180,.F.); -#34406=ORIENTED_EDGE('',*,*,#34405,.T.); -#34407=ORIENTED_EDGE('',*,*,#28349,.T.); -#34409=ORIENTED_EDGE('',*,*,#34408,.F.); -#34410=EDGE_LOOP('',(#34404,#34406,#34407,#34409)); -#34411=FACE_OUTER_BOUND('',#34410,.F.); -#34413=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,5.44375E0)); -#34414=DIRECTION('',(8.697566915162E-1,0.E0,4.934807975625E-1)); -#34415=DIRECTION('',(4.934807975625E-1,0.E0,-8.697566915162E-1)); -#34416=AXIS2_PLACEMENT_3D('',#34413,#34414,#34415); -#34417=PLANE('',#34416); -#34418=ORIENTED_EDGE('',*,*,#25246,.F.); -#34420=ORIENTED_EDGE('',*,*,#34419,.T.); -#34421=ORIENTED_EDGE('',*,*,#28351,.T.); -#34422=ORIENTED_EDGE('',*,*,#34405,.F.); -#34423=EDGE_LOOP('',(#34418,#34420,#34421,#34422)); -#34424=FACE_OUTER_BOUND('',#34423,.F.); -#34426=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,5.5E0)); -#34427=DIRECTION('',(6.611562980142E-1,0.E0,7.502481919980E-1)); -#34428=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#34429=AXIS2_PLACEMENT_3D('',#34426,#34427,#34428); -#34430=PLANE('',#34429); -#34431=ORIENTED_EDGE('',*,*,#25244,.F.); -#34433=ORIENTED_EDGE('',*,*,#34432,.T.); -#34434=ORIENTED_EDGE('',*,*,#28353,.T.); -#34435=ORIENTED_EDGE('',*,*,#34419,.F.); -#34436=EDGE_LOOP('',(#34431,#34433,#34434,#34435)); -#34437=FACE_OUTER_BOUND('',#34436,.F.); -#34439=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,5.537499856949E0)); -#34440=DIRECTION('',(4.032164835459E-1,0.E0,9.151046210116E-1)); -#34441=DIRECTION('',(9.151046210116E-1,0.E0,-4.032164835459E-1)); -#34442=AXIS2_PLACEMENT_3D('',#34439,#34440,#34441); -#34443=PLANE('',#34442); -#34444=ORIENTED_EDGE('',*,*,#25242,.F.); -#34446=ORIENTED_EDGE('',*,*,#34445,.T.); -#34447=ORIENTED_EDGE('',*,*,#28355,.T.); -#34448=ORIENTED_EDGE('',*,*,#34432,.F.); -#34449=EDGE_LOOP('',(#34444,#34446,#34447,#34448)); -#34450=FACE_OUTER_BOUND('',#34449,.F.); -#34452=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.537499856949E0)); -#34453=DIRECTION('',(0.E0,0.E0,1.E0)); -#34454=DIRECTION('',(1.E0,0.E0,0.E0)); -#34455=AXIS2_PLACEMENT_3D('',#34452,#34453,#34454); -#34456=PLANE('',#34455); -#34457=ORIENTED_EDGE('',*,*,#25240,.F.); -#34459=ORIENTED_EDGE('',*,*,#34458,.T.); -#34460=ORIENTED_EDGE('',*,*,#28357,.T.); -#34461=ORIENTED_EDGE('',*,*,#34445,.F.); -#34462=EDGE_LOOP('',(#34457,#34459,#34460,#34461)); -#34463=FACE_OUTER_BOUND('',#34462,.F.); -#34465=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.5E0)); -#34466=DIRECTION('',(-3.324488400931E-1,0.E0,9.431212905670E-1)); -#34467=DIRECTION('',(9.431212905670E-1,0.E0,3.324488400931E-1)); -#34468=AXIS2_PLACEMENT_3D('',#34465,#34466,#34467); -#34469=PLANE('',#34468); -#34470=ORIENTED_EDGE('',*,*,#25238,.F.); -#34472=ORIENTED_EDGE('',*,*,#34471,.T.); -#34473=ORIENTED_EDGE('',*,*,#28359,.T.); -#34474=ORIENTED_EDGE('',*,*,#34458,.F.); -#34475=EDGE_LOOP('',(#34470,#34472,#34473,#34474)); -#34476=FACE_OUTER_BOUND('',#34475,.F.); -#34478=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,5.44375E0)); -#34479=DIRECTION('',(-6.611562980142E-1,0.E0,7.502481919980E-1)); -#34480=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#34481=AXIS2_PLACEMENT_3D('',#34478,#34479,#34480); -#34482=PLANE('',#34481); -#34483=ORIENTED_EDGE('',*,*,#25236,.F.); -#34485=ORIENTED_EDGE('',*,*,#34484,.T.); -#34486=ORIENTED_EDGE('',*,*,#28361,.T.); -#34487=ORIENTED_EDGE('',*,*,#34471,.F.); -#34488=EDGE_LOOP('',(#34483,#34485,#34486,#34487)); -#34489=FACE_OUTER_BOUND('',#34488,.F.); -#34491=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.350000143051E0)); -#34492=DIRECTION('',(-8.265988793059E-1,0.E0,5.627915179978E-1)); -#34493=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#34494=AXIS2_PLACEMENT_3D('',#34491,#34492,#34493); -#34495=PLANE('',#34494); -#34496=ORIENTED_EDGE('',*,*,#25234,.F.); -#34498=ORIENTED_EDGE('',*,*,#34497,.T.); -#34499=ORIENTED_EDGE('',*,*,#28363,.T.); -#34500=ORIENTED_EDGE('',*,*,#34484,.F.); -#34501=EDGE_LOOP('',(#34496,#34498,#34499,#34500)); -#34502=FACE_OUTER_BOUND('',#34501,.F.); -#34504=CARTESIAN_POINT('',(3.E0,1.55E0,5.256249856949E0)); -#34505=DIRECTION('',(-9.752009016921E-1,0.E0,2.213214886517E-1)); -#34506=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#34507=AXIS2_PLACEMENT_3D('',#34504,#34505,#34506); -#34508=PLANE('',#34507); -#34509=ORIENTED_EDGE('',*,*,#25232,.F.); -#34511=ORIENTED_EDGE('',*,*,#34510,.T.); -#34512=ORIENTED_EDGE('',*,*,#28365,.T.); -#34513=ORIENTED_EDGE('',*,*,#34497,.F.); -#34514=EDGE_LOOP('',(#34509,#34511,#34512,#34513)); -#34515=FACE_OUTER_BOUND('',#34514,.F.); -#34517=CARTESIAN_POINT('',(3.E0,1.55E0,5.181250143051E0)); -#34518=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34519=DIRECTION('',(0.E0,0.E0,1.E0)); -#34520=AXIS2_PLACEMENT_3D('',#34517,#34518,#34519); -#34521=PLANE('',#34520); -#34522=ORIENTED_EDGE('',*,*,#25230,.F.); -#34524=ORIENTED_EDGE('',*,*,#34523,.T.); -#34525=ORIENTED_EDGE('',*,*,#28367,.T.); -#34526=ORIENTED_EDGE('',*,*,#34510,.F.); -#34527=EDGE_LOOP('',(#34522,#34524,#34525,#34526)); -#34528=FACE_OUTER_BOUND('',#34527,.F.); -#34530=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,5.087499856949E0)); -#34531=DIRECTION('',(-9.752009016921E-1,0.E0,-2.213214886517E-1)); -#34532=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#34533=AXIS2_PLACEMENT_3D('',#34530,#34531,#34532); -#34534=PLANE('',#34533); -#34535=ORIENTED_EDGE('',*,*,#25228,.F.); -#34537=ORIENTED_EDGE('',*,*,#34536,.T.); -#34538=ORIENTED_EDGE('',*,*,#28369,.T.); -#34539=ORIENTED_EDGE('',*,*,#34523,.F.); -#34540=EDGE_LOOP('',(#34535,#34537,#34538,#34539)); -#34541=FACE_OUTER_BOUND('',#34540,.F.); -#34543=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,4.99375E0)); -#34544=DIRECTION('',(-8.265988793059E-1,0.E0,-5.627915179978E-1)); -#34545=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#34546=AXIS2_PLACEMENT_3D('',#34543,#34544,#34545); -#34547=PLANE('',#34546); -#34548=ORIENTED_EDGE('',*,*,#25226,.F.); -#34550=ORIENTED_EDGE('',*,*,#34549,.T.); -#34551=ORIENTED_EDGE('',*,*,#28371,.T.); -#34552=ORIENTED_EDGE('',*,*,#34536,.F.); -#34553=EDGE_LOOP('',(#34548,#34550,#34551,#34552)); -#34554=FACE_OUTER_BOUND('',#34553,.F.); -#34556=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,4.9375E0)); -#34557=DIRECTION('',(-6.611562980142E-1,0.E0,-7.502481919980E-1)); -#34558=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#34559=AXIS2_PLACEMENT_3D('',#34556,#34557,#34558); -#34560=PLANE('',#34559); -#34561=ORIENTED_EDGE('',*,*,#25224,.F.); -#34563=ORIENTED_EDGE('',*,*,#34562,.T.); -#34564=ORIENTED_EDGE('',*,*,#28373,.T.); -#34565=ORIENTED_EDGE('',*,*,#34549,.F.); -#34566=EDGE_LOOP('',(#34561,#34563,#34564,#34565)); -#34567=FACE_OUTER_BOUND('',#34566,.F.); -#34569=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.900000143051E0)); -#34570=DIRECTION('',(-3.324488400931E-1,0.E0,-9.431212905670E-1)); -#34571=DIRECTION('',(-9.431212905670E-1,0.E0,3.324488400931E-1)); -#34572=AXIS2_PLACEMENT_3D('',#34569,#34570,#34571); -#34573=PLANE('',#34572); -#34574=ORIENTED_EDGE('',*,*,#25222,.F.); -#34576=ORIENTED_EDGE('',*,*,#34575,.T.); -#34577=ORIENTED_EDGE('',*,*,#28375,.T.); -#34578=ORIENTED_EDGE('',*,*,#34562,.F.); -#34579=EDGE_LOOP('',(#34574,#34576,#34577,#34578)); -#34580=FACE_OUTER_BOUND('',#34579,.F.); -#34582=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,4.900000143051E0)); -#34583=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34584=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34585=AXIS2_PLACEMENT_3D('',#34582,#34583,#34584); -#34586=PLANE('',#34585); -#34587=ORIENTED_EDGE('',*,*,#25220,.F.); -#34589=ORIENTED_EDGE('',*,*,#34588,.T.); -#34590=ORIENTED_EDGE('',*,*,#28377,.T.); -#34591=ORIENTED_EDGE('',*,*,#34575,.F.); -#34592=EDGE_LOOP('',(#34587,#34589,#34590,#34591)); -#34593=FACE_OUTER_BOUND('',#34592,.F.); -#34595=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,4.9375E0)); -#34596=DIRECTION('',(4.032164835459E-1,0.E0,-9.151046210116E-1)); -#34597=DIRECTION('',(-9.151046210116E-1,0.E0,-4.032164835459E-1)); -#34598=AXIS2_PLACEMENT_3D('',#34595,#34596,#34597); -#34599=PLANE('',#34598); -#34600=ORIENTED_EDGE('',*,*,#25218,.F.); -#34602=ORIENTED_EDGE('',*,*,#34601,.T.); -#34603=ORIENTED_EDGE('',*,*,#28379,.T.); -#34604=ORIENTED_EDGE('',*,*,#34588,.F.); -#34605=EDGE_LOOP('',(#34600,#34602,#34603,#34604)); -#34606=FACE_OUTER_BOUND('',#34605,.F.); -#34608=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,4.99375E0)); -#34609=DIRECTION('',(6.611562980142E-1,0.E0,-7.502481919980E-1)); -#34610=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#34611=AXIS2_PLACEMENT_3D('',#34608,#34609,#34610); -#34612=PLANE('',#34611); -#34613=ORIENTED_EDGE('',*,*,#25216,.F.); -#34615=ORIENTED_EDGE('',*,*,#34614,.T.); -#34616=ORIENTED_EDGE('',*,*,#28381,.T.); -#34617=ORIENTED_EDGE('',*,*,#34601,.F.); -#34618=EDGE_LOOP('',(#34613,#34615,#34616,#34617)); -#34619=FACE_OUTER_BOUND('',#34618,.F.); -#34621=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,5.031249856949E0)); -#34622=DIRECTION('',(8.697566915162E-1,0.E0,-4.934807975625E-1)); -#34623=DIRECTION('',(-4.934807975625E-1,0.E0,-8.697566915162E-1)); -#34624=AXIS2_PLACEMENT_3D('',#34621,#34622,#34623); -#34625=PLANE('',#34624); -#34626=ORIENTED_EDGE('',*,*,#25214,.F.); -#34628=ORIENTED_EDGE('',*,*,#34627,.T.); -#34629=ORIENTED_EDGE('',*,*,#28383,.T.); -#34630=ORIENTED_EDGE('',*,*,#34614,.F.); -#34631=EDGE_LOOP('',(#34626,#34628,#34629,#34630)); -#34632=FACE_OUTER_BOUND('',#34631,.F.); -#34634=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,4.99375E0)); -#34635=DIRECTION('',(-8.697566915162E-1,0.E0,-4.934807975625E-1)); -#34636=DIRECTION('',(-4.934807975625E-1,0.E0,8.697566915162E-1)); -#34637=AXIS2_PLACEMENT_3D('',#34634,#34635,#34636); -#34638=PLANE('',#34637); -#34639=ORIENTED_EDGE('',*,*,#25212,.F.); -#34641=ORIENTED_EDGE('',*,*,#34640,.T.); -#34642=ORIENTED_EDGE('',*,*,#28385,.T.); -#34643=ORIENTED_EDGE('',*,*,#34627,.F.); -#34644=EDGE_LOOP('',(#34639,#34641,#34642,#34643)); -#34645=FACE_OUTER_BOUND('',#34644,.F.); -#34647=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,4.918749856949E0)); -#34648=DIRECTION('',(-7.615400379714E-1,0.E0,-6.481178678037E-1)); -#34649=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#34650=AXIS2_PLACEMENT_3D('',#34647,#34648,#34649); -#34651=PLANE('',#34650); -#34652=ORIENTED_EDGE('',*,*,#25210,.F.); -#34654=ORIENTED_EDGE('',*,*,#34653,.T.); -#34655=ORIENTED_EDGE('',*,*,#28387,.T.); -#34656=ORIENTED_EDGE('',*,*,#34640,.F.); -#34657=EDGE_LOOP('',(#34652,#34654,#34655,#34656)); -#34658=FACE_OUTER_BOUND('',#34657,.F.); -#34660=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.88125E0)); -#34661=DIRECTION('',(-3.324489229327E-1,0.E0,-9.431212613662E-1)); -#34662=DIRECTION('',(-9.431212613662E-1,0.E0,3.324489229327E-1)); -#34663=AXIS2_PLACEMENT_3D('',#34660,#34661,#34662); -#34664=PLANE('',#34663); -#34665=ORIENTED_EDGE('',*,*,#25208,.F.); -#34667=ORIENTED_EDGE('',*,*,#34666,.T.); -#34668=ORIENTED_EDGE('',*,*,#28389,.T.); -#34669=ORIENTED_EDGE('',*,*,#34653,.F.); -#34670=EDGE_LOOP('',(#34665,#34667,#34668,#34669)); -#34671=FACE_OUTER_BOUND('',#34670,.F.); -#34673=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.88125E0)); -#34674=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34675=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34676=AXIS2_PLACEMENT_3D('',#34673,#34674,#34675); -#34677=PLANE('',#34676); -#34678=ORIENTED_EDGE('',*,*,#25206,.F.); -#34680=ORIENTED_EDGE('',*,*,#34679,.T.); -#34681=ORIENTED_EDGE('',*,*,#28391,.T.); -#34682=ORIENTED_EDGE('',*,*,#34666,.F.); -#34683=EDGE_LOOP('',(#34678,#34680,#34681,#34682)); -#34684=FACE_OUTER_BOUND('',#34683,.F.); -#34686=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,4.918749856949E0)); -#34687=DIRECTION('',(3.324489643525E-1,0.E0,-9.431212467657E-1)); -#34688=DIRECTION('',(-9.431212467657E-1,0.E0,-3.324489643525E-1)); -#34689=AXIS2_PLACEMENT_3D('',#34686,#34687,#34688); -#34690=PLANE('',#34689); -#34691=ORIENTED_EDGE('',*,*,#25204,.F.); -#34693=ORIENTED_EDGE('',*,*,#34692,.T.); -#34694=ORIENTED_EDGE('',*,*,#28393,.T.); -#34695=ORIENTED_EDGE('',*,*,#34679,.F.); -#34696=EDGE_LOOP('',(#34691,#34693,#34694,#34695)); -#34697=FACE_OUTER_BOUND('',#34696,.F.); -#34699=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,4.974999856949E0)); -#34700=DIRECTION('',(6.611562545751E-1,0.E0,-7.502482302787E-1)); -#34701=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#34702=AXIS2_PLACEMENT_3D('',#34699,#34700,#34701); -#34703=PLANE('',#34702); -#34704=ORIENTED_EDGE('',*,*,#25202,.F.); -#34706=ORIENTED_EDGE('',*,*,#34705,.T.); -#34707=ORIENTED_EDGE('',*,*,#28395,.T.); -#34708=ORIENTED_EDGE('',*,*,#34692,.F.); -#34709=EDGE_LOOP('',(#34704,#34706,#34707,#34708)); -#34710=FACE_OUTER_BOUND('',#34709,.F.); -#34712=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.068750143051E0)); -#34713=DIRECTION('',(8.266000548632E-1,0.E0,-5.627897913965E-1)); -#34714=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#34715=AXIS2_PLACEMENT_3D('',#34712,#34713,#34714); -#34716=PLANE('',#34715); -#34717=ORIENTED_EDGE('',*,*,#25200,.F.); -#34719=ORIENTED_EDGE('',*,*,#34718,.T.); -#34720=ORIENTED_EDGE('',*,*,#28397,.T.); -#34721=ORIENTED_EDGE('',*,*,#34705,.F.); -#34722=EDGE_LOOP('',(#34717,#34719,#34720,#34721)); -#34723=FACE_OUTER_BOUND('',#34722,.F.); -#34725=CARTESIAN_POINT('',(4.E0,1.55E0,5.1625E0)); -#34726=DIRECTION('',(9.752006788427E-1,0.E0,-2.213224705823E-1)); -#34727=DIRECTION('',(-2.213224705823E-1,0.E0,-9.752006788427E-1)); -#34728=AXIS2_PLACEMENT_3D('',#34725,#34726,#34727); -#34729=PLANE('',#34728); -#34730=ORIENTED_EDGE('',*,*,#25198,.F.); -#34732=ORIENTED_EDGE('',*,*,#34731,.T.); -#34733=ORIENTED_EDGE('',*,*,#28399,.T.); -#34734=ORIENTED_EDGE('',*,*,#34718,.F.); -#34735=EDGE_LOOP('',(#34730,#34732,#34733,#34734)); -#34736=FACE_OUTER_BOUND('',#34735,.F.); -#34738=CARTESIAN_POINT('',(4.E0,1.55E0,5.275E0)); -#34739=DIRECTION('',(1.E0,0.E0,0.E0)); -#34740=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34741=AXIS2_PLACEMENT_3D('',#34738,#34739,#34740); -#34742=PLANE('',#34741); -#34743=ORIENTED_EDGE('',*,*,#25196,.F.); -#34745=ORIENTED_EDGE('',*,*,#34744,.T.); -#34746=ORIENTED_EDGE('',*,*,#28401,.T.); -#34747=ORIENTED_EDGE('',*,*,#34731,.F.); -#34748=EDGE_LOOP('',(#34743,#34745,#34746,#34747)); -#34749=FACE_OUTER_BOUND('',#34748,.F.); -#34751=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,5.368749856949E0)); -#34752=DIRECTION('',(9.752006788427E-1,0.E0,2.213224705823E-1)); -#34753=DIRECTION('',(2.213224705823E-1,0.E0,-9.752006788427E-1)); -#34754=AXIS2_PLACEMENT_3D('',#34751,#34752,#34753); -#34755=PLANE('',#34754); -#34756=ORIENTED_EDGE('',*,*,#25194,.F.); -#34758=ORIENTED_EDGE('',*,*,#34757,.T.); -#34759=ORIENTED_EDGE('',*,*,#28403,.T.); -#34760=ORIENTED_EDGE('',*,*,#34744,.F.); -#34761=EDGE_LOOP('',(#34756,#34758,#34759,#34760)); -#34762=FACE_OUTER_BOUND('',#34761,.F.); -#34764=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,5.462500143051E0)); -#34765=DIRECTION('',(8.266000548632E-1,0.E0,5.627897913965E-1)); -#34766=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#34767=AXIS2_PLACEMENT_3D('',#34764,#34765,#34766); -#34768=PLANE('',#34767); -#34769=ORIENTED_EDGE('',*,*,#25192,.F.); -#34771=ORIENTED_EDGE('',*,*,#34770,.T.); -#34772=ORIENTED_EDGE('',*,*,#28405,.T.); -#34773=ORIENTED_EDGE('',*,*,#34757,.F.); -#34774=EDGE_LOOP('',(#34769,#34771,#34772,#34773)); -#34775=FACE_OUTER_BOUND('',#34774,.F.); -#34777=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,5.518750143051E0)); -#34778=DIRECTION('',(6.611562545751E-1,0.E0,7.502482302787E-1)); -#34779=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#34780=AXIS2_PLACEMENT_3D('',#34777,#34778,#34779); -#34781=PLANE('',#34780); -#34782=ORIENTED_EDGE('',*,*,#25190,.F.); -#34784=ORIENTED_EDGE('',*,*,#34783,.T.); -#34785=ORIENTED_EDGE('',*,*,#28407,.T.); -#34786=ORIENTED_EDGE('',*,*,#34770,.F.); -#34787=EDGE_LOOP('',(#34782,#34784,#34785,#34786)); -#34788=FACE_OUTER_BOUND('',#34787,.F.); -#34790=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.55625E0)); -#34791=DIRECTION('',(3.324489643525E-1,0.E0,9.431212467657E-1)); -#34792=DIRECTION('',(9.431212467657E-1,0.E0,-3.324489643525E-1)); -#34793=AXIS2_PLACEMENT_3D('',#34790,#34791,#34792); -#34794=PLANE('',#34793); -#34795=ORIENTED_EDGE('',*,*,#25188,.F.); -#34797=ORIENTED_EDGE('',*,*,#34796,.T.); -#34798=ORIENTED_EDGE('',*,*,#28409,.T.); -#34799=ORIENTED_EDGE('',*,*,#34783,.F.); -#34800=EDGE_LOOP('',(#34795,#34797,#34798,#34799)); -#34801=FACE_OUTER_BOUND('',#34800,.F.); -#34803=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.55625E0)); -#34804=DIRECTION('',(0.E0,0.E0,1.E0)); -#34805=DIRECTION('',(1.E0,0.E0,0.E0)); -#34806=AXIS2_PLACEMENT_3D('',#34803,#34804,#34805); -#34807=PLANE('',#34806); -#34808=ORIENTED_EDGE('',*,*,#25186,.F.); -#34810=ORIENTED_EDGE('',*,*,#34809,.T.); -#34811=ORIENTED_EDGE('',*,*,#28411,.T.); -#34812=ORIENTED_EDGE('',*,*,#34796,.F.); -#34813=EDGE_LOOP('',(#34808,#34810,#34811,#34812)); -#34814=FACE_OUTER_BOUND('',#34813,.F.); -#34816=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,5.518750143051E0)); -#34817=DIRECTION('',(-3.324489229327E-1,0.E0,9.431212613662E-1)); -#34818=DIRECTION('',(9.431212613662E-1,0.E0,3.324489229327E-1)); -#34819=AXIS2_PLACEMENT_3D('',#34816,#34817,#34818); -#34820=PLANE('',#34819); -#34821=ORIENTED_EDGE('',*,*,#25184,.F.); -#34823=ORIENTED_EDGE('',*,*,#34822,.T.); -#34824=ORIENTED_EDGE('',*,*,#28413,.T.); -#34825=ORIENTED_EDGE('',*,*,#34809,.F.); -#34826=EDGE_LOOP('',(#34821,#34823,#34824,#34825)); -#34827=FACE_OUTER_BOUND('',#34826,.F.); -#34829=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,5.44375E0)); -#34830=DIRECTION('',(-7.615400379714E-1,0.E0,6.481178678037E-1)); -#34831=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#34832=AXIS2_PLACEMENT_3D('',#34829,#34830,#34831); -#34833=PLANE('',#34832); -#34834=ORIENTED_EDGE('',*,*,#25182,.F.); -#34835=ORIENTED_EDGE('',*,*,#34408,.T.); -#34836=ORIENTED_EDGE('',*,*,#28415,.T.); -#34837=ORIENTED_EDGE('',*,*,#34822,.F.); -#34838=EDGE_LOOP('',(#34834,#34835,#34836,#34837)); -#34839=FACE_OUTER_BOUND('',#34838,.F.); -#34841=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.256249856949E0)); -#34842=DIRECTION('',(-9.620373440297E-1,0.E0,-2.729178423855E-1)); -#34843=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#34844=AXIS2_PLACEMENT_3D('',#34841,#34842,#34843); -#34845=PLANE('',#34844); -#34846=ORIENTED_EDGE('',*,*,#26502,.F.); -#34848=ORIENTED_EDGE('',*,*,#34847,.T.); -#34849=ORIENTED_EDGE('',*,*,#28419,.T.); -#34851=ORIENTED_EDGE('',*,*,#34850,.F.); -#34852=EDGE_LOOP('',(#34846,#34848,#34849,#34851)); -#34853=FACE_OUTER_BOUND('',#34852,.F.); -#34855=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.181250143051E0)); -#34856=DIRECTION('',(-1.E0,0.E0,0.E0)); -#34857=DIRECTION('',(0.E0,0.E0,1.E0)); -#34858=AXIS2_PLACEMENT_3D('',#34855,#34856,#34857); -#34859=PLANE('',#34858); -#34860=ORIENTED_EDGE('',*,*,#26532,.F.); -#34862=ORIENTED_EDGE('',*,*,#34861,.T.); -#34863=ORIENTED_EDGE('',*,*,#28421,.T.); -#34864=ORIENTED_EDGE('',*,*,#34847,.F.); -#34865=EDGE_LOOP('',(#34860,#34862,#34863,#34864)); -#34866=FACE_OUTER_BOUND('',#34865,.F.); -#34868=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.10625E0)); -#34869=DIRECTION('',(-9.620373440297E-1,0.E0,2.729178423855E-1)); -#34870=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#34871=AXIS2_PLACEMENT_3D('',#34868,#34869,#34870); -#34872=PLANE('',#34871); -#34873=ORIENTED_EDGE('',*,*,#26530,.F.); -#34875=ORIENTED_EDGE('',*,*,#34874,.T.); -#34876=ORIENTED_EDGE('',*,*,#28423,.T.); -#34877=ORIENTED_EDGE('',*,*,#34861,.F.); -#34878=EDGE_LOOP('',(#34873,#34875,#34876,#34877)); -#34879=FACE_OUTER_BOUND('',#34878,.F.); -#34881=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.031249856949E0)); -#34882=DIRECTION('',(-8.697579034767E-1,0.E0,4.934786614838E-1)); -#34883=DIRECTION('',(4.934786614838E-1,0.E0,8.697579034767E-1)); -#34884=AXIS2_PLACEMENT_3D('',#34881,#34882,#34883); -#34885=PLANE('',#34884); -#34886=ORIENTED_EDGE('',*,*,#26528,.F.); -#34888=ORIENTED_EDGE('',*,*,#34887,.T.); -#34889=ORIENTED_EDGE('',*,*,#28425,.T.); -#34890=ORIENTED_EDGE('',*,*,#34874,.F.); -#34891=EDGE_LOOP('',(#34886,#34888,#34889,#34890)); -#34892=FACE_OUTER_BOUND('',#34891,.F.); -#34894=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,4.974999856949E0)); -#34895=DIRECTION('',(-5.513868654785E-1,0.E0,8.342496776013E-1)); -#34896=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#34897=AXIS2_PLACEMENT_3D('',#34894,#34895,#34896); -#34898=PLANE('',#34897); -#34899=ORIENTED_EDGE('',*,*,#26526,.F.); -#34901=ORIENTED_EDGE('',*,*,#34900,.T.); -#34902=ORIENTED_EDGE('',*,*,#28427,.T.); -#34903=ORIENTED_EDGE('',*,*,#34887,.F.); -#34904=EDGE_LOOP('',(#34899,#34901,#34902,#34903)); -#34905=FACE_OUTER_BOUND('',#34904,.F.); -#34907=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.974999856949E0)); -#34908=DIRECTION('',(0.E0,0.E0,1.E0)); -#34909=DIRECTION('',(1.E0,0.E0,0.E0)); -#34910=AXIS2_PLACEMENT_3D('',#34907,#34908,#34909); -#34911=PLANE('',#34910); -#34912=ORIENTED_EDGE('',*,*,#26524,.F.); -#34914=ORIENTED_EDGE('',*,*,#34913,.T.); -#34915=ORIENTED_EDGE('',*,*,#28429,.T.); -#34916=ORIENTED_EDGE('',*,*,#34900,.F.); -#34917=EDGE_LOOP('',(#34912,#34914,#34915,#34916)); -#34918=FACE_OUTER_BOUND('',#34917,.F.); -#34920=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.031249856949E0)); -#34921=DIRECTION('',(5.513867982882E-1,0.E0,8.342497220099E-1)); -#34922=DIRECTION('',(8.342497220099E-1,0.E0,-5.513867982882E-1)); -#34923=AXIS2_PLACEMENT_3D('',#34920,#34921,#34922); -#34924=PLANE('',#34923); -#34925=ORIENTED_EDGE('',*,*,#26522,.F.); -#34927=ORIENTED_EDGE('',*,*,#34926,.T.); -#34928=ORIENTED_EDGE('',*,*,#28431,.T.); -#34929=ORIENTED_EDGE('',*,*,#34913,.F.); -#34930=EDGE_LOOP('',(#34925,#34927,#34928,#34929)); -#34931=FACE_OUTER_BOUND('',#34930,.F.); -#34933=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.10625E0)); -#34934=DIRECTION('',(8.697579034767E-1,0.E0,4.934786614838E-1)); -#34935=DIRECTION('',(4.934786614838E-1,0.E0,-8.697579034767E-1)); -#34936=AXIS2_PLACEMENT_3D('',#34933,#34934,#34935); -#34937=PLANE('',#34936); -#34938=ORIENTED_EDGE('',*,*,#26520,.F.); -#34940=ORIENTED_EDGE('',*,*,#34939,.T.); -#34941=ORIENTED_EDGE('',*,*,#28433,.T.); -#34942=ORIENTED_EDGE('',*,*,#34926,.F.); -#34943=EDGE_LOOP('',(#34938,#34940,#34941,#34942)); -#34944=FACE_OUTER_BOUND('',#34943,.F.); -#34946=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.181250143051E0)); -#34947=DIRECTION('',(9.620373440297E-1,0.E0,2.729178423855E-1)); -#34948=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#34949=AXIS2_PLACEMENT_3D('',#34946,#34947,#34948); -#34950=PLANE('',#34949); -#34951=ORIENTED_EDGE('',*,*,#26518,.F.); -#34953=ORIENTED_EDGE('',*,*,#34952,.T.); -#34954=ORIENTED_EDGE('',*,*,#28435,.T.); -#34955=ORIENTED_EDGE('',*,*,#34939,.F.); -#34956=EDGE_LOOP('',(#34951,#34953,#34954,#34955)); -#34957=FACE_OUTER_BOUND('',#34956,.F.); -#34959=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.256249856949E0)); -#34960=DIRECTION('',(1.E0,0.E0,0.E0)); -#34961=DIRECTION('',(0.E0,0.E0,-1.E0)); -#34962=AXIS2_PLACEMENT_3D('',#34959,#34960,#34961); -#34963=PLANE('',#34962); -#34964=ORIENTED_EDGE('',*,*,#26516,.F.); -#34966=ORIENTED_EDGE('',*,*,#34965,.T.); -#34967=ORIENTED_EDGE('',*,*,#28437,.T.); -#34968=ORIENTED_EDGE('',*,*,#34952,.F.); -#34969=EDGE_LOOP('',(#34964,#34966,#34967,#34968)); -#34970=FACE_OUTER_BOUND('',#34969,.F.); -#34972=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,5.33125E0)); -#34973=DIRECTION('',(9.620373440297E-1,0.E0,-2.729178423855E-1)); -#34974=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#34975=AXIS2_PLACEMENT_3D('',#34972,#34973,#34974); -#34976=PLANE('',#34975); -#34977=ORIENTED_EDGE('',*,*,#26514,.F.); -#34979=ORIENTED_EDGE('',*,*,#34978,.T.); -#34980=ORIENTED_EDGE('',*,*,#28439,.T.); -#34981=ORIENTED_EDGE('',*,*,#34965,.F.); -#34982=EDGE_LOOP('',(#34977,#34979,#34980,#34981)); -#34983=FACE_OUTER_BOUND('',#34982,.F.); -#34985=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,5.406250143051E0)); -#34986=DIRECTION('',(8.697579034767E-1,0.E0,-4.934786614838E-1)); -#34987=DIRECTION('',(-4.934786614838E-1,0.E0,-8.697579034767E-1)); -#34988=AXIS2_PLACEMENT_3D('',#34985,#34986,#34987); -#34989=PLANE('',#34988); -#34990=ORIENTED_EDGE('',*,*,#26512,.F.); -#34992=ORIENTED_EDGE('',*,*,#34991,.T.); -#34993=ORIENTED_EDGE('',*,*,#28441,.T.); -#34994=ORIENTED_EDGE('',*,*,#34978,.F.); -#34995=EDGE_LOOP('',(#34990,#34992,#34993,#34994)); -#34996=FACE_OUTER_BOUND('',#34995,.F.); -#34998=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.462500143051E0)); -#34999=DIRECTION('',(5.513867982882E-1,0.E0,-8.342497220099E-1)); -#35000=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#35001=AXIS2_PLACEMENT_3D('',#34998,#34999,#35000); -#35002=PLANE('',#35001); -#35003=ORIENTED_EDGE('',*,*,#26510,.F.); -#35005=ORIENTED_EDGE('',*,*,#35004,.T.); -#35006=ORIENTED_EDGE('',*,*,#28443,.T.); -#35007=ORIENTED_EDGE('',*,*,#34991,.F.); -#35008=EDGE_LOOP('',(#35003,#35005,#35006,#35007)); -#35009=FACE_OUTER_BOUND('',#35008,.F.); -#35011=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,5.462500143051E0)); -#35012=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35013=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35014=AXIS2_PLACEMENT_3D('',#35011,#35012,#35013); -#35015=PLANE('',#35014); -#35016=ORIENTED_EDGE('',*,*,#26508,.F.); -#35018=ORIENTED_EDGE('',*,*,#35017,.T.); -#35019=ORIENTED_EDGE('',*,*,#28445,.T.); -#35020=ORIENTED_EDGE('',*,*,#35004,.F.); -#35021=EDGE_LOOP('',(#35016,#35018,#35019,#35020)); -#35022=FACE_OUTER_BOUND('',#35021,.F.); -#35024=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,5.406250143051E0)); -#35025=DIRECTION('',(-5.513868654785E-1,0.E0,-8.342496776013E-1)); -#35026=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654785E-1)); -#35027=AXIS2_PLACEMENT_3D('',#35024,#35025,#35026); -#35028=PLANE('',#35027); -#35029=ORIENTED_EDGE('',*,*,#26506,.F.); -#35031=ORIENTED_EDGE('',*,*,#35030,.T.); -#35032=ORIENTED_EDGE('',*,*,#28447,.T.); -#35033=ORIENTED_EDGE('',*,*,#35017,.F.); -#35034=EDGE_LOOP('',(#35029,#35031,#35032,#35033)); -#35035=FACE_OUTER_BOUND('',#35034,.F.); -#35037=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,5.33125E0)); -#35038=DIRECTION('',(-8.697579034767E-1,0.E0,-4.934786614838E-1)); -#35039=DIRECTION('',(-4.934786614838E-1,0.E0,8.697579034767E-1)); -#35040=AXIS2_PLACEMENT_3D('',#35037,#35038,#35039); -#35041=PLANE('',#35040); -#35042=ORIENTED_EDGE('',*,*,#26504,.F.); -#35043=ORIENTED_EDGE('',*,*,#34850,.T.); -#35044=ORIENTED_EDGE('',*,*,#28449,.T.); -#35045=ORIENTED_EDGE('',*,*,#35030,.F.); -#35046=EDGE_LOOP('',(#35042,#35043,#35044,#35045)); -#35047=FACE_OUTER_BOUND('',#35046,.F.); -#35049=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.181250143051E0)); -#35050=DIRECTION('',(9.620373440297E-1,0.E0,2.729178423855E-1)); -#35051=DIRECTION('',(2.729178423855E-1,0.E0,-9.620373440297E-1)); -#35052=AXIS2_PLACEMENT_3D('',#35049,#35050,#35051); -#35053=PLANE('',#35052); -#35054=ORIENTED_EDGE('',*,*,#26542,.F.); -#35056=ORIENTED_EDGE('',*,*,#35055,.T.); -#35057=ORIENTED_EDGE('',*,*,#28453,.T.); -#35059=ORIENTED_EDGE('',*,*,#35058,.F.); -#35060=EDGE_LOOP('',(#35054,#35056,#35057,#35059)); -#35061=FACE_OUTER_BOUND('',#35060,.F.); -#35063=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,5.256249856949E0)); -#35064=DIRECTION('',(1.E0,0.E0,0.E0)); -#35065=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35066=AXIS2_PLACEMENT_3D('',#35063,#35064,#35065); -#35067=PLANE('',#35066); -#35068=ORIENTED_EDGE('',*,*,#26572,.F.); -#35070=ORIENTED_EDGE('',*,*,#35069,.T.); -#35071=ORIENTED_EDGE('',*,*,#28455,.T.); -#35072=ORIENTED_EDGE('',*,*,#35055,.F.); -#35073=EDGE_LOOP('',(#35068,#35070,#35071,#35072)); -#35074=FACE_OUTER_BOUND('',#35073,.F.); -#35076=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.33125E0)); -#35077=DIRECTION('',(9.620373440297E-1,0.E0,-2.729178423855E-1)); -#35078=DIRECTION('',(-2.729178423855E-1,0.E0,-9.620373440297E-1)); -#35079=AXIS2_PLACEMENT_3D('',#35076,#35077,#35078); -#35080=PLANE('',#35079); -#35081=ORIENTED_EDGE('',*,*,#26570,.F.); -#35083=ORIENTED_EDGE('',*,*,#35082,.T.); -#35084=ORIENTED_EDGE('',*,*,#28457,.T.); -#35085=ORIENTED_EDGE('',*,*,#35069,.F.); -#35086=EDGE_LOOP('',(#35081,#35083,#35084,#35085)); -#35087=FACE_OUTER_BOUND('',#35086,.F.); -#35089=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.406250143051E0)); -#35090=DIRECTION('',(7.615400379714E-1,0.E0,-6.481178678037E-1)); -#35091=DIRECTION('',(-6.481178678037E-1,0.E0,-7.615400379714E-1)); -#35092=AXIS2_PLACEMENT_3D('',#35089,#35090,#35091); -#35093=PLANE('',#35092); -#35094=ORIENTED_EDGE('',*,*,#26568,.F.); -#35096=ORIENTED_EDGE('',*,*,#35095,.T.); -#35097=ORIENTED_EDGE('',*,*,#28459,.T.); -#35098=ORIENTED_EDGE('',*,*,#35082,.F.); -#35099=EDGE_LOOP('',(#35094,#35096,#35097,#35098)); -#35100=FACE_OUTER_BOUND('',#35099,.F.); -#35102=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,5.44375E0)); -#35103=DIRECTION('',(5.065473053637E-1,0.E0,-8.622121707728E-1)); -#35104=DIRECTION('',(-8.622121707728E-1,0.E0,-5.065473053637E-1)); -#35105=AXIS2_PLACEMENT_3D('',#35102,#35103,#35104); -#35106=PLANE('',#35105); -#35107=ORIENTED_EDGE('',*,*,#26566,.F.); -#35109=ORIENTED_EDGE('',*,*,#35108,.T.); -#35110=ORIENTED_EDGE('',*,*,#28461,.T.); -#35111=ORIENTED_EDGE('',*,*,#35095,.F.); -#35112=EDGE_LOOP('',(#35107,#35109,#35110,#35111)); -#35113=FACE_OUTER_BOUND('',#35112,.F.); -#35115=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,5.44375E0)); -#35116=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35117=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35118=AXIS2_PLACEMENT_3D('',#35115,#35116,#35117); -#35119=PLANE('',#35118); -#35120=ORIENTED_EDGE('',*,*,#26564,.F.); -#35122=ORIENTED_EDGE('',*,*,#35121,.T.); -#35123=ORIENTED_EDGE('',*,*,#28463,.T.); -#35124=ORIENTED_EDGE('',*,*,#35108,.F.); -#35125=EDGE_LOOP('',(#35120,#35122,#35123,#35124)); -#35126=FACE_OUTER_BOUND('',#35125,.F.); -#35128=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.406250143051E0)); -#35129=DIRECTION('',(-5.065476570090E-1,0.E0,-8.622119641820E-1)); -#35130=DIRECTION('',(-8.622119641820E-1,0.E0,5.065476570090E-1)); -#35131=AXIS2_PLACEMENT_3D('',#35128,#35129,#35130); -#35132=PLANE('',#35131); -#35133=ORIENTED_EDGE('',*,*,#26562,.F.); -#35135=ORIENTED_EDGE('',*,*,#35134,.T.); -#35136=ORIENTED_EDGE('',*,*,#28465,.T.); -#35137=ORIENTED_EDGE('',*,*,#35121,.F.); -#35138=EDGE_LOOP('',(#35133,#35135,#35136,#35137)); -#35139=FACE_OUTER_BOUND('',#35138,.F.); -#35141=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.33125E0)); -#35142=DIRECTION('',(-7.615400379714E-1,0.E0,-6.481178678037E-1)); -#35143=DIRECTION('',(-6.481178678037E-1,0.E0,7.615400379714E-1)); -#35144=AXIS2_PLACEMENT_3D('',#35141,#35142,#35143); -#35145=PLANE('',#35144); -#35146=ORIENTED_EDGE('',*,*,#26560,.F.); -#35148=ORIENTED_EDGE('',*,*,#35147,.T.); -#35149=ORIENTED_EDGE('',*,*,#28467,.T.); -#35150=ORIENTED_EDGE('',*,*,#35134,.F.); -#35151=EDGE_LOOP('',(#35146,#35148,#35149,#35150)); -#35152=FACE_OUTER_BOUND('',#35151,.F.); -#35154=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.256249856949E0)); -#35155=DIRECTION('',(-9.620373440297E-1,0.E0,-2.729178423855E-1)); -#35156=DIRECTION('',(-2.729178423855E-1,0.E0,9.620373440297E-1)); -#35157=AXIS2_PLACEMENT_3D('',#35154,#35155,#35156); -#35158=PLANE('',#35157); -#35159=ORIENTED_EDGE('',*,*,#26558,.F.); -#35161=ORIENTED_EDGE('',*,*,#35160,.T.); -#35162=ORIENTED_EDGE('',*,*,#28469,.T.); -#35163=ORIENTED_EDGE('',*,*,#35147,.F.); -#35164=EDGE_LOOP('',(#35159,#35161,#35162,#35163)); -#35165=FACE_OUTER_BOUND('',#35164,.F.); -#35167=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,5.181250143051E0)); -#35168=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35169=DIRECTION('',(0.E0,0.E0,1.E0)); -#35170=AXIS2_PLACEMENT_3D('',#35167,#35168,#35169); -#35171=PLANE('',#35170); -#35172=ORIENTED_EDGE('',*,*,#26556,.F.); -#35174=ORIENTED_EDGE('',*,*,#35173,.T.); -#35175=ORIENTED_EDGE('',*,*,#28471,.T.); -#35176=ORIENTED_EDGE('',*,*,#35160,.F.); -#35177=EDGE_LOOP('',(#35172,#35174,#35175,#35176)); -#35178=FACE_OUTER_BOUND('',#35177,.F.); -#35180=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.10625E0)); -#35181=DIRECTION('',(-9.620373440297E-1,0.E0,2.729178423855E-1)); -#35182=DIRECTION('',(2.729178423855E-1,0.E0,9.620373440297E-1)); -#35183=AXIS2_PLACEMENT_3D('',#35180,#35181,#35182); -#35184=PLANE('',#35183); -#35185=ORIENTED_EDGE('',*,*,#26554,.F.); -#35187=ORIENTED_EDGE('',*,*,#35186,.T.); -#35188=ORIENTED_EDGE('',*,*,#28473,.T.); -#35189=ORIENTED_EDGE('',*,*,#35173,.F.); -#35190=EDGE_LOOP('',(#35185,#35187,#35188,#35189)); -#35191=FACE_OUTER_BOUND('',#35190,.F.); -#35193=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.031249856949E0)); -#35194=DIRECTION('',(-7.615400379714E-1,0.E0,6.481178678037E-1)); -#35195=DIRECTION('',(6.481178678037E-1,0.E0,7.615400379714E-1)); -#35196=AXIS2_PLACEMENT_3D('',#35193,#35194,#35195); -#35197=PLANE('',#35196); -#35198=ORIENTED_EDGE('',*,*,#26552,.F.); -#35200=ORIENTED_EDGE('',*,*,#35199,.T.); -#35201=ORIENTED_EDGE('',*,*,#28475,.T.); -#35202=ORIENTED_EDGE('',*,*,#35186,.F.); -#35203=EDGE_LOOP('',(#35198,#35200,#35201,#35202)); -#35204=FACE_OUTER_BOUND('',#35203,.F.); -#35206=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,4.99375E0)); -#35207=DIRECTION('',(-5.065476570090E-1,0.E0,8.622119641820E-1)); -#35208=DIRECTION('',(8.622119641820E-1,0.E0,5.065476570090E-1)); -#35209=AXIS2_PLACEMENT_3D('',#35206,#35207,#35208); -#35210=PLANE('',#35209); -#35211=ORIENTED_EDGE('',*,*,#26550,.F.); -#35213=ORIENTED_EDGE('',*,*,#35212,.T.); -#35214=ORIENTED_EDGE('',*,*,#28477,.T.); -#35215=ORIENTED_EDGE('',*,*,#35199,.F.); -#35216=EDGE_LOOP('',(#35211,#35213,#35214,#35215)); -#35217=FACE_OUTER_BOUND('',#35216,.F.); -#35219=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,4.99375E0)); -#35220=DIRECTION('',(0.E0,0.E0,1.E0)); -#35221=DIRECTION('',(1.E0,0.E0,0.E0)); -#35222=AXIS2_PLACEMENT_3D('',#35219,#35220,#35221); -#35223=PLANE('',#35222); -#35224=ORIENTED_EDGE('',*,*,#26548,.F.); -#35226=ORIENTED_EDGE('',*,*,#35225,.T.); -#35227=ORIENTED_EDGE('',*,*,#28479,.T.); -#35228=ORIENTED_EDGE('',*,*,#35212,.F.); -#35229=EDGE_LOOP('',(#35224,#35226,#35227,#35228)); -#35230=FACE_OUTER_BOUND('',#35229,.F.); -#35232=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,5.031249856949E0)); -#35233=DIRECTION('',(5.065473053637E-1,0.E0,8.622121707728E-1)); -#35234=DIRECTION('',(8.622121707728E-1,0.E0,-5.065473053637E-1)); -#35235=AXIS2_PLACEMENT_3D('',#35232,#35233,#35234); -#35236=PLANE('',#35235); -#35237=ORIENTED_EDGE('',*,*,#26546,.F.); -#35239=ORIENTED_EDGE('',*,*,#35238,.T.); -#35240=ORIENTED_EDGE('',*,*,#28481,.T.); -#35241=ORIENTED_EDGE('',*,*,#35225,.F.); -#35242=EDGE_LOOP('',(#35237,#35239,#35240,#35241)); -#35243=FACE_OUTER_BOUND('',#35242,.F.); -#35245=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,5.10625E0)); -#35246=DIRECTION('',(7.615400379714E-1,0.E0,6.481178678037E-1)); -#35247=DIRECTION('',(6.481178678037E-1,0.E0,-7.615400379714E-1)); -#35248=AXIS2_PLACEMENT_3D('',#35245,#35246,#35247); -#35249=PLANE('',#35248); -#35250=ORIENTED_EDGE('',*,*,#26544,.F.); -#35251=ORIENTED_EDGE('',*,*,#35058,.T.); -#35252=ORIENTED_EDGE('',*,*,#28483,.T.); -#35253=ORIENTED_EDGE('',*,*,#35238,.F.); -#35254=EDGE_LOOP('',(#35250,#35251,#35252,#35253)); -#35255=FACE_OUTER_BOUND('',#35254,.F.); -#35257=CARTESIAN_POINT('',(4.E0,1.55E0,4.43125E0)); -#35258=DIRECTION('',(1.824133632822E-1,0.E0,-9.832219306424E-1)); -#35259=DIRECTION('',(-9.832219306424E-1,0.E0,-1.824133632822E-1)); -#35260=AXIS2_PLACEMENT_3D('',#35257,#35258,#35259); -#35261=PLANE('',#35260); -#35262=ORIENTED_EDGE('',*,*,#25250,.F.); -#35264=ORIENTED_EDGE('',*,*,#35263,.T.); -#35265=ORIENTED_EDGE('',*,*,#28500,.T.); -#35267=ORIENTED_EDGE('',*,*,#35266,.F.); -#35268=EDGE_LOOP('',(#35262,#35264,#35265,#35267)); -#35269=FACE_OUTER_BOUND('',#35268,.F.); -#35271=CARTESIAN_POINT('',(4.E0,1.55E0,4.581249856949E0)); -#35272=DIRECTION('',(1.E0,0.E0,0.E0)); -#35273=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35274=AXIS2_PLACEMENT_3D('',#35271,#35272,#35273); -#35275=PLANE('',#35274); -#35276=ORIENTED_EDGE('',*,*,#25274,.F.); -#35278=ORIENTED_EDGE('',*,*,#35277,.T.); -#35279=ORIENTED_EDGE('',*,*,#28502,.T.); -#35280=ORIENTED_EDGE('',*,*,#35263,.F.); -#35281=EDGE_LOOP('',(#35276,#35278,#35279,#35280)); -#35282=FACE_OUTER_BOUND('',#35281,.F.); -#35284=CARTESIAN_POINT('',(3.E0,1.55E0,4.731250143051E0)); -#35285=DIRECTION('',(1.483407296412E-1,0.E0,9.889363113616E-1)); -#35286=DIRECTION('',(9.889363113616E-1,0.E0,-1.483407296412E-1)); -#35287=AXIS2_PLACEMENT_3D('',#35284,#35285,#35286); -#35288=PLANE('',#35287); -#35289=ORIENTED_EDGE('',*,*,#25272,.F.); -#35291=ORIENTED_EDGE('',*,*,#35290,.T.); -#35292=ORIENTED_EDGE('',*,*,#28504,.T.); -#35293=ORIENTED_EDGE('',*,*,#35277,.F.); -#35294=EDGE_LOOP('',(#35289,#35291,#35292,#35293)); -#35295=FACE_OUTER_BOUND('',#35294,.F.); -#35297=CARTESIAN_POINT('',(3.E0,1.55E0,4.618750143051E0)); -#35298=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35299=DIRECTION('',(0.E0,0.E0,1.E0)); -#35300=AXIS2_PLACEMENT_3D('',#35297,#35298,#35299); -#35301=PLANE('',#35300); -#35302=ORIENTED_EDGE('',*,*,#25270,.F.); -#35304=ORIENTED_EDGE('',*,*,#35303,.T.); -#35305=ORIENTED_EDGE('',*,*,#28506,.T.); -#35306=ORIENTED_EDGE('',*,*,#35290,.F.); -#35307=EDGE_LOOP('',(#35302,#35304,#35305,#35306)); -#35308=FACE_OUTER_BOUND('',#35307,.F.); -#35310=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.506250143051E0)); -#35311=DIRECTION('',(-1.453159661591E-1,0.E0,-9.893852990515E-1)); -#35312=DIRECTION('',(-9.893852990515E-1,0.E0,1.453159661591E-1)); -#35313=AXIS2_PLACEMENT_3D('',#35310,#35311,#35312); -#35314=PLANE('',#35313); -#35315=ORIENTED_EDGE('',*,*,#25268,.F.); -#35317=ORIENTED_EDGE('',*,*,#35316,.T.); -#35318=ORIENTED_EDGE('',*,*,#28508,.T.); -#35319=ORIENTED_EDGE('',*,*,#35303,.F.); -#35320=EDGE_LOOP('',(#35315,#35317,#35318,#35319)); -#35321=FACE_OUTER_BOUND('',#35320,.F.); -#35323=CARTESIAN_POINT('',(3.E0,1.55E0,4.356249856949E0)); -#35324=DIRECTION('',(-1.921831848318E-1,0.E0,9.813590695907E-1)); -#35325=DIRECTION('',(9.813590695907E-1,0.E0,1.921831848318E-1)); -#35326=AXIS2_PLACEMENT_3D('',#35323,#35324,#35325); -#35327=PLANE('',#35326); -#35328=ORIENTED_EDGE('',*,*,#25266,.F.); -#35330=ORIENTED_EDGE('',*,*,#35329,.T.); -#35331=ORIENTED_EDGE('',*,*,#28510,.T.); -#35332=ORIENTED_EDGE('',*,*,#35316,.F.); -#35333=EDGE_LOOP('',(#35328,#35330,#35331,#35332)); -#35334=FACE_OUTER_BOUND('',#35333,.F.); -#35336=CARTESIAN_POINT('',(3.E0,1.55E0,4.20625E0)); -#35337=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35338=DIRECTION('',(0.E0,0.E0,1.E0)); -#35339=AXIS2_PLACEMENT_3D('',#35336,#35337,#35338); -#35340=PLANE('',#35339); -#35341=ORIENTED_EDGE('',*,*,#25264,.F.); -#35343=ORIENTED_EDGE('',*,*,#35342,.T.); -#35344=ORIENTED_EDGE('',*,*,#28512,.T.); -#35345=ORIENTED_EDGE('',*,*,#35329,.F.); -#35346=EDGE_LOOP('',(#35341,#35343,#35344,#35345)); -#35347=FACE_OUTER_BOUND('',#35346,.F.); -#35349=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.056250143051E0)); -#35350=DIRECTION('',(-1.921826553002E-1,0.E0,-9.813591732907E-1)); -#35351=DIRECTION('',(-9.813591732907E-1,0.E0,1.921826553002E-1)); -#35352=AXIS2_PLACEMENT_3D('',#35349,#35350,#35351); -#35353=PLANE('',#35352); -#35354=ORIENTED_EDGE('',*,*,#25262,.F.); -#35356=ORIENTED_EDGE('',*,*,#35355,.T.); -#35357=ORIENTED_EDGE('',*,*,#28514,.T.); -#35358=ORIENTED_EDGE('',*,*,#35342,.F.); -#35359=EDGE_LOOP('',(#35354,#35356,#35357,#35358)); -#35360=FACE_OUTER_BOUND('',#35359,.F.); -#35362=CARTESIAN_POINT('',(3.E0,1.55E0,3.943750143051E0)); -#35363=DIRECTION('',(-1.453159661591E-1,0.E0,9.893852990515E-1)); -#35364=DIRECTION('',(9.893852990515E-1,0.E0,1.453159661591E-1)); -#35365=AXIS2_PLACEMENT_3D('',#35362,#35363,#35364); -#35366=PLANE('',#35365); -#35367=ORIENTED_EDGE('',*,*,#25260,.F.); -#35369=ORIENTED_EDGE('',*,*,#35368,.T.); -#35370=ORIENTED_EDGE('',*,*,#28516,.T.); -#35371=ORIENTED_EDGE('',*,*,#35355,.F.); -#35372=EDGE_LOOP('',(#35367,#35369,#35370,#35371)); -#35373=FACE_OUTER_BOUND('',#35372,.F.); -#35375=CARTESIAN_POINT('',(3.E0,1.55E0,3.831250143051E0)); -#35376=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35377=DIRECTION('',(0.E0,0.E0,1.E0)); -#35378=AXIS2_PLACEMENT_3D('',#35375,#35376,#35377); -#35379=PLANE('',#35378); -#35380=ORIENTED_EDGE('',*,*,#25258,.F.); -#35382=ORIENTED_EDGE('',*,*,#35381,.T.); -#35383=ORIENTED_EDGE('',*,*,#28518,.T.); -#35384=ORIENTED_EDGE('',*,*,#35368,.F.); -#35385=EDGE_LOOP('',(#35380,#35382,#35383,#35384)); -#35386=FACE_OUTER_BOUND('',#35385,.F.); -#35388=CARTESIAN_POINT('',(4.E0,1.55E0,3.98125E0)); -#35389=DIRECTION('',(1.483403145748E-1,0.E0,-9.889363736216E-1)); -#35390=DIRECTION('',(-9.889363736216E-1,0.E0,-1.483403145748E-1)); -#35391=AXIS2_PLACEMENT_3D('',#35388,#35389,#35390); -#35392=PLANE('',#35391); -#35393=ORIENTED_EDGE('',*,*,#25256,.F.); -#35395=ORIENTED_EDGE('',*,*,#35394,.T.); -#35396=ORIENTED_EDGE('',*,*,#28520,.T.); -#35397=ORIENTED_EDGE('',*,*,#35381,.F.); -#35398=EDGE_LOOP('',(#35393,#35395,#35396,#35397)); -#35399=FACE_OUTER_BOUND('',#35398,.F.); -#35401=CARTESIAN_POINT('',(4.E0,1.55E0,4.131249856949E0)); -#35402=DIRECTION('',(1.E0,0.E0,0.E0)); -#35403=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35404=AXIS2_PLACEMENT_3D('',#35401,#35402,#35403); -#35405=PLANE('',#35404); -#35406=ORIENTED_EDGE('',*,*,#25254,.F.); -#35408=ORIENTED_EDGE('',*,*,#35407,.T.); -#35409=ORIENTED_EDGE('',*,*,#28522,.T.); -#35410=ORIENTED_EDGE('',*,*,#35394,.F.); -#35411=EDGE_LOOP('',(#35406,#35408,#35409,#35410)); -#35412=FACE_OUTER_BOUND('',#35411,.F.); -#35414=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,4.281250143051E0)); -#35415=DIRECTION('',(1.824138678057E-1,0.E0,9.832218370399E-1)); -#35416=DIRECTION('',(9.832218370399E-1,0.E0,-1.824138678057E-1)); -#35417=AXIS2_PLACEMENT_3D('',#35414,#35415,#35416); -#35418=PLANE('',#35417); -#35419=ORIENTED_EDGE('',*,*,#25252,.F.); -#35420=ORIENTED_EDGE('',*,*,#35266,.T.); -#35421=ORIENTED_EDGE('',*,*,#28524,.T.); -#35422=ORIENTED_EDGE('',*,*,#35407,.F.); -#35423=EDGE_LOOP('',(#35419,#35420,#35421,#35422)); -#35424=FACE_OUTER_BOUND('',#35423,.F.); -#35426=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,3.099999713898E0)); -#35427=DIRECTION('',(8.697542675479E-1,0.E0,-4.934850697662E-1)); -#35428=DIRECTION('',(-4.934850697662E-1,0.E0,-8.697542675479E-1)); -#35429=AXIS2_PLACEMENT_3D('',#35426,#35427,#35428); -#35430=PLANE('',#35429); -#35431=ORIENTED_EDGE('',*,*,#25278,.F.); -#35433=ORIENTED_EDGE('',*,*,#35432,.T.); -#35434=ORIENTED_EDGE('',*,*,#28541,.T.); -#35436=ORIENTED_EDGE('',*,*,#35435,.F.); -#35437=EDGE_LOOP('',(#35431,#35433,#35434,#35436)); -#35438=FACE_OUTER_BOUND('',#35437,.F.); -#35440=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,3.062500286102E0)); -#35441=DIRECTION('',(-8.697542675479E-1,0.E0,-4.934850697662E-1)); -#35442=DIRECTION('',(-4.934850697662E-1,0.E0,8.697542675479E-1)); -#35443=AXIS2_PLACEMENT_3D('',#35440,#35441,#35442); -#35444=PLANE('',#35443); -#35445=ORIENTED_EDGE('',*,*,#25314,.F.); -#35447=ORIENTED_EDGE('',*,*,#35446,.T.); -#35448=ORIENTED_EDGE('',*,*,#28543,.T.); -#35449=ORIENTED_EDGE('',*,*,#35432,.F.); -#35450=EDGE_LOOP('',(#35445,#35447,#35448,#35449)); -#35451=FACE_OUTER_BOUND('',#35450,.F.); -#35453=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,3.006250286102E0)); -#35454=DIRECTION('',(-5.513869326687E-1,0.E0,-8.342496331927E-1)); -#35455=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#35456=AXIS2_PLACEMENT_3D('',#35453,#35454,#35455); -#35457=PLANE('',#35456); -#35458=ORIENTED_EDGE('',*,*,#25312,.F.); -#35460=ORIENTED_EDGE('',*,*,#35459,.T.); -#35461=ORIENTED_EDGE('',*,*,#28545,.T.); -#35462=ORIENTED_EDGE('',*,*,#35446,.F.); -#35463=EDGE_LOOP('',(#35458,#35460,#35461,#35462)); -#35464=FACE_OUTER_BOUND('',#35463,.F.); -#35466=CARTESIAN_POINT('',(3.659574478865E0,1.55E0,2.987499713898E0)); -#35467=DIRECTION('',(-2.818494771324E-1,0.E0,-9.594586349813E-1)); -#35468=DIRECTION('',(-9.594586349813E-1,0.E0,2.818494771324E-1)); -#35469=AXIS2_PLACEMENT_3D('',#35466,#35467,#35468); -#35470=PLANE('',#35469); -#35471=ORIENTED_EDGE('',*,*,#25310,.F.); -#35473=ORIENTED_EDGE('',*,*,#35472,.T.); -#35474=ORIENTED_EDGE('',*,*,#28547,.T.); -#35475=ORIENTED_EDGE('',*,*,#35459,.F.); -#35476=EDGE_LOOP('',(#35471,#35473,#35474,#35475)); -#35477=FACE_OUTER_BOUND('',#35476,.F.); -#35479=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,2.987499713898E0)); -#35480=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35481=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35482=AXIS2_PLACEMENT_3D('',#35479,#35480,#35481); -#35483=PLANE('',#35482); -#35484=ORIENTED_EDGE('',*,*,#25308,.F.); -#35486=ORIENTED_EDGE('',*,*,#35485,.T.); -#35487=ORIENTED_EDGE('',*,*,#28549,.T.); -#35488=ORIENTED_EDGE('',*,*,#35472,.F.); -#35489=EDGE_LOOP('',(#35484,#35486,#35487,#35488)); -#35490=FACE_OUTER_BOUND('',#35489,.F.); -#35492=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,3.006250286102E0)); -#35493=DIRECTION('',(2.818495377036E-1,0.E0,-9.594586171880E-1)); -#35494=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#35495=AXIS2_PLACEMENT_3D('',#35492,#35493,#35494); -#35496=PLANE('',#35495); -#35497=ORIENTED_EDGE('',*,*,#25306,.F.); -#35499=ORIENTED_EDGE('',*,*,#35498,.T.); -#35500=ORIENTED_EDGE('',*,*,#28551,.T.); -#35501=ORIENTED_EDGE('',*,*,#35485,.F.); -#35502=EDGE_LOOP('',(#35497,#35499,#35500,#35501)); -#35503=FACE_OUTER_BOUND('',#35502,.F.); -#35505=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,3.062500286102E0)); -#35506=DIRECTION('',(5.513868990736E-1,0.E0,-8.342496553970E-1)); -#35507=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#35508=AXIS2_PLACEMENT_3D('',#35505,#35506,#35507); -#35509=PLANE('',#35508); -#35510=ORIENTED_EDGE('',*,*,#25304,.F.); -#35512=ORIENTED_EDGE('',*,*,#35511,.T.); -#35513=ORIENTED_EDGE('',*,*,#28553,.T.); -#35514=ORIENTED_EDGE('',*,*,#35498,.F.); -#35515=EDGE_LOOP('',(#35510,#35512,#35513,#35514)); -#35516=FACE_OUTER_BOUND('',#35515,.F.); -#35518=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,3.1375E0)); -#35519=DIRECTION('',(7.615381795356E-1,0.E0,-6.481200514639E-1)); -#35520=DIRECTION('',(-6.481200514639E-1,0.E0,-7.615381795356E-1)); -#35521=AXIS2_PLACEMENT_3D('',#35518,#35519,#35520); -#35522=PLANE('',#35521); -#35523=ORIENTED_EDGE('',*,*,#25302,.F.); -#35525=ORIENTED_EDGE('',*,*,#35524,.T.); -#35526=ORIENTED_EDGE('',*,*,#28555,.T.); -#35527=ORIENTED_EDGE('',*,*,#35511,.F.); -#35528=EDGE_LOOP('',(#35523,#35525,#35526,#35527)); -#35529=FACE_OUTER_BOUND('',#35528,.F.); -#35531=CARTESIAN_POINT('',(4.E0,1.55E0,3.231250286102E0)); -#35532=DIRECTION('',(9.752008975102E-1,0.E0,-2.213215070781E-1)); -#35533=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#35534=AXIS2_PLACEMENT_3D('',#35531,#35532,#35533); -#35535=PLANE('',#35534); -#35536=ORIENTED_EDGE('',*,*,#25300,.F.); -#35538=ORIENTED_EDGE('',*,*,#35537,.T.); -#35539=ORIENTED_EDGE('',*,*,#28557,.T.); -#35540=ORIENTED_EDGE('',*,*,#35524,.F.); -#35541=EDGE_LOOP('',(#35536,#35538,#35539,#35540)); -#35542=FACE_OUTER_BOUND('',#35541,.F.); -#35544=CARTESIAN_POINT('',(4.E0,1.55E0,3.681249856949E0)); -#35545=DIRECTION('',(1.E0,0.E0,0.E0)); -#35546=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35547=AXIS2_PLACEMENT_3D('',#35544,#35545,#35546); -#35548=PLANE('',#35547); -#35549=ORIENTED_EDGE('',*,*,#25298,.F.); -#35551=ORIENTED_EDGE('',*,*,#35550,.T.); -#35552=ORIENTED_EDGE('',*,*,#28559,.T.); -#35553=ORIENTED_EDGE('',*,*,#35537,.F.); -#35554=EDGE_LOOP('',(#35549,#35551,#35552,#35553)); -#35555=FACE_OUTER_BOUND('',#35554,.F.); -#35557=CARTESIAN_POINT('',(3.E0,1.55E0,3.681249856949E0)); -#35558=DIRECTION('',(0.E0,0.E0,1.E0)); -#35559=DIRECTION('',(1.E0,0.E0,0.E0)); -#35560=AXIS2_PLACEMENT_3D('',#35557,#35558,#35559); -#35561=PLANE('',#35560); -#35562=ORIENTED_EDGE('',*,*,#25296,.F.); -#35564=ORIENTED_EDGE('',*,*,#35563,.T.); -#35565=ORIENTED_EDGE('',*,*,#28561,.T.); -#35566=ORIENTED_EDGE('',*,*,#35550,.F.); -#35567=EDGE_LOOP('',(#35562,#35564,#35565,#35566)); -#35568=FACE_OUTER_BOUND('',#35567,.F.); -#35570=CARTESIAN_POINT('',(3.E0,1.55E0,3.231250286102E0)); -#35571=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35572=DIRECTION('',(0.E0,0.E0,1.E0)); -#35573=AXIS2_PLACEMENT_3D('',#35570,#35571,#35572); -#35574=PLANE('',#35573); -#35575=ORIENTED_EDGE('',*,*,#25294,.F.); -#35577=ORIENTED_EDGE('',*,*,#35576,.T.); -#35578=ORIENTED_EDGE('',*,*,#28563,.T.); -#35579=ORIENTED_EDGE('',*,*,#35563,.F.); -#35580=EDGE_LOOP('',(#35575,#35577,#35578,#35579)); -#35581=FACE_OUTER_BOUND('',#35580,.F.); -#35583=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,3.1375E0)); -#35584=DIRECTION('',(-9.752009016921E-1,0.E0,-2.213214886517E-1)); -#35585=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#35586=AXIS2_PLACEMENT_3D('',#35583,#35584,#35585); -#35587=PLANE('',#35586); -#35588=ORIENTED_EDGE('',*,*,#25292,.F.); -#35590=ORIENTED_EDGE('',*,*,#35589,.T.); -#35591=ORIENTED_EDGE('',*,*,#28565,.T.); -#35592=ORIENTED_EDGE('',*,*,#35576,.F.); -#35593=EDGE_LOOP('',(#35588,#35590,#35591,#35592)); -#35594=FACE_OUTER_BOUND('',#35593,.F.); -#35596=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,3.062500286102E0)); -#35597=DIRECTION('',(-7.615382075403E-1,0.E0,-6.481200185586E-1)); -#35598=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#35599=AXIS2_PLACEMENT_3D('',#35596,#35597,#35598); -#35600=PLANE('',#35599); -#35601=ORIENTED_EDGE('',*,*,#25290,.F.); -#35603=ORIENTED_EDGE('',*,*,#35602,.T.); -#35604=ORIENTED_EDGE('',*,*,#28567,.T.); -#35605=ORIENTED_EDGE('',*,*,#35589,.F.); -#35606=EDGE_LOOP('',(#35601,#35603,#35604,#35605)); -#35607=FACE_OUTER_BOUND('',#35606,.F.); -#35609=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,3.006250286102E0)); -#35610=DIRECTION('',(-5.513869326687E-1,0.E0,-8.342496331927E-1)); -#35611=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#35612=AXIS2_PLACEMENT_3D('',#35609,#35610,#35611); -#35613=PLANE('',#35612); -#35614=ORIENTED_EDGE('',*,*,#25288,.F.); -#35616=ORIENTED_EDGE('',*,*,#35615,.T.); -#35617=ORIENTED_EDGE('',*,*,#28569,.T.); -#35618=ORIENTED_EDGE('',*,*,#35602,.F.); -#35619=EDGE_LOOP('',(#35614,#35616,#35617,#35618)); -#35620=FACE_OUTER_BOUND('',#35619,.F.); -#35622=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.987499713898E0)); -#35623=DIRECTION('',(-2.818495982749E-1,0.E0,-9.594585993946E-1)); -#35624=DIRECTION('',(-9.594585993946E-1,0.E0,2.818495982749E-1)); -#35625=AXIS2_PLACEMENT_3D('',#35622,#35623,#35624); -#35626=PLANE('',#35625); -#35627=ORIENTED_EDGE('',*,*,#25286,.F.); -#35629=ORIENTED_EDGE('',*,*,#35628,.T.); -#35630=ORIENTED_EDGE('',*,*,#28571,.T.); -#35631=ORIENTED_EDGE('',*,*,#35615,.F.); -#35632=EDGE_LOOP('',(#35627,#35629,#35630,#35631)); -#35633=FACE_OUTER_BOUND('',#35632,.F.); -#35635=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,2.987499713898E0)); -#35636=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35637=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35638=AXIS2_PLACEMENT_3D('',#35635,#35636,#35637); -#35639=PLANE('',#35638); -#35640=ORIENTED_EDGE('',*,*,#25284,.F.); -#35642=ORIENTED_EDGE('',*,*,#35641,.T.); -#35643=ORIENTED_EDGE('',*,*,#28573,.T.); -#35644=ORIENTED_EDGE('',*,*,#35628,.F.); -#35645=EDGE_LOOP('',(#35640,#35642,#35643,#35644)); -#35646=FACE_OUTER_BOUND('',#35645,.F.); -#35648=CARTESIAN_POINT('',(3.382978737354E0,1.55E0,3.006250286102E0)); -#35649=DIRECTION('',(2.818495982749E-1,0.E0,-9.594585993946E-1)); -#35650=DIRECTION('',(-9.594585993946E-1,0.E0,-2.818495982749E-1)); -#35651=AXIS2_PLACEMENT_3D('',#35648,#35649,#35650); -#35652=PLANE('',#35651); -#35653=ORIENTED_EDGE('',*,*,#25282,.F.); -#35655=ORIENTED_EDGE('',*,*,#35654,.T.); -#35656=ORIENTED_EDGE('',*,*,#28575,.T.); -#35657=ORIENTED_EDGE('',*,*,#35641,.F.); -#35658=EDGE_LOOP('',(#35653,#35655,#35656,#35657)); -#35659=FACE_OUTER_BOUND('',#35658,.F.); -#35661=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,3.062500286102E0)); -#35662=DIRECTION('',(5.513869326687E-1,0.E0,-8.342496331927E-1)); -#35663=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#35664=AXIS2_PLACEMENT_3D('',#35661,#35662,#35663); -#35665=PLANE('',#35664); -#35666=ORIENTED_EDGE('',*,*,#25280,.F.); -#35667=ORIENTED_EDGE('',*,*,#35435,.T.); -#35668=ORIENTED_EDGE('',*,*,#28577,.T.); -#35669=ORIENTED_EDGE('',*,*,#35654,.F.); -#35670=EDGE_LOOP('',(#35666,#35667,#35668,#35669)); -#35671=FACE_OUTER_BOUND('',#35670,.F.); -#35673=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.568749856949E0)); -#35674=DIRECTION('',(1.E0,0.E0,0.E0)); -#35675=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35676=AXIS2_PLACEMENT_3D('',#35673,#35674,#35675); -#35677=PLANE('',#35676); -#35678=ORIENTED_EDGE('',*,*,#26582,.F.); -#35680=ORIENTED_EDGE('',*,*,#35679,.T.); -#35681=ORIENTED_EDGE('',*,*,#28581,.T.); -#35683=ORIENTED_EDGE('',*,*,#35682,.F.); -#35684=EDGE_LOOP('',(#35678,#35680,#35681,#35683)); -#35685=FACE_OUTER_BOUND('',#35684,.F.); -#35687=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.568749856949E0)); -#35688=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35689=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35690=AXIS2_PLACEMENT_3D('',#35687,#35688,#35689); -#35691=PLANE('',#35690); -#35692=ORIENTED_EDGE('',*,*,#26600,.F.); -#35694=ORIENTED_EDGE('',*,*,#35693,.T.); -#35695=ORIENTED_EDGE('',*,*,#28583,.T.); -#35696=ORIENTED_EDGE('',*,*,#35679,.F.); -#35697=EDGE_LOOP('',(#35692,#35694,#35695,#35696)); -#35698=FACE_OUTER_BOUND('',#35697,.F.); -#35700=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,3.212499713898E0)); -#35701=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35702=DIRECTION('',(0.E0,0.E0,1.E0)); -#35703=AXIS2_PLACEMENT_3D('',#35700,#35701,#35702); -#35704=PLANE('',#35703); -#35705=ORIENTED_EDGE('',*,*,#26598,.F.); -#35707=ORIENTED_EDGE('',*,*,#35706,.T.); -#35708=ORIENTED_EDGE('',*,*,#28585,.T.); -#35709=ORIENTED_EDGE('',*,*,#35693,.F.); -#35710=EDGE_LOOP('',(#35705,#35707,#35708,#35709)); -#35711=FACE_OUTER_BOUND('',#35710,.F.); -#35713=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,3.156249713898E0)); -#35714=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#35715=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#35716=AXIS2_PLACEMENT_3D('',#35713,#35714,#35715); -#35717=PLANE('',#35716); -#35718=ORIENTED_EDGE('',*,*,#26596,.F.); -#35720=ORIENTED_EDGE('',*,*,#35719,.T.); -#35721=ORIENTED_EDGE('',*,*,#28587,.T.); -#35722=ORIENTED_EDGE('',*,*,#35706,.F.); -#35723=EDGE_LOOP('',(#35718,#35720,#35721,#35722)); -#35724=FACE_OUTER_BOUND('',#35723,.F.); -#35726=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,3.118750286102E0)); -#35727=DIRECTION('',(-6.611506194509E-1,0.E0,7.502531961943E-1)); -#35728=DIRECTION('',(7.502531961943E-1,0.E0,6.611506194509E-1)); -#35729=AXIS2_PLACEMENT_3D('',#35726,#35727,#35728); -#35730=PLANE('',#35729); -#35731=ORIENTED_EDGE('',*,*,#26594,.F.); -#35733=ORIENTED_EDGE('',*,*,#35732,.T.); -#35734=ORIENTED_EDGE('',*,*,#28589,.T.); -#35735=ORIENTED_EDGE('',*,*,#35719,.F.); -#35736=EDGE_LOOP('',(#35731,#35733,#35734,#35735)); -#35737=FACE_OUTER_BOUND('',#35736,.F.); -#35739=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,3.099999713898E0)); -#35740=DIRECTION('',(-2.818495982749E-1,0.E0,9.594585993946E-1)); -#35741=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#35742=AXIS2_PLACEMENT_3D('',#35739,#35740,#35741); -#35743=PLANE('',#35742); -#35744=ORIENTED_EDGE('',*,*,#26592,.F.); -#35746=ORIENTED_EDGE('',*,*,#35745,.T.); -#35747=ORIENTED_EDGE('',*,*,#28591,.T.); -#35748=ORIENTED_EDGE('',*,*,#35732,.F.); -#35749=EDGE_LOOP('',(#35744,#35746,#35747,#35748)); -#35750=FACE_OUTER_BOUND('',#35749,.F.); -#35752=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,3.099999713898E0)); -#35753=DIRECTION('',(0.E0,0.E0,1.E0)); -#35754=DIRECTION('',(1.E0,0.E0,0.E0)); -#35755=AXIS2_PLACEMENT_3D('',#35752,#35753,#35754); -#35756=PLANE('',#35755); -#35757=ORIENTED_EDGE('',*,*,#26590,.F.); -#35759=ORIENTED_EDGE('',*,*,#35758,.T.); -#35760=ORIENTED_EDGE('',*,*,#28593,.T.); -#35761=ORIENTED_EDGE('',*,*,#35745,.F.); -#35762=EDGE_LOOP('',(#35757,#35759,#35760,#35761)); -#35763=FACE_OUTER_BOUND('',#35762,.F.); -#35765=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,3.118750286102E0)); -#35766=DIRECTION('',(2.818493559900E-1,0.E0,9.594586705679E-1)); -#35767=DIRECTION('',(9.594586705679E-1,0.E0,-2.818493559900E-1)); -#35768=AXIS2_PLACEMENT_3D('',#35765,#35766,#35767); -#35769=PLANE('',#35768); -#35770=ORIENTED_EDGE('',*,*,#26588,.F.); -#35772=ORIENTED_EDGE('',*,*,#35771,.T.); -#35773=ORIENTED_EDGE('',*,*,#28595,.T.); -#35774=ORIENTED_EDGE('',*,*,#35758,.F.); -#35775=EDGE_LOOP('',(#35770,#35772,#35773,#35774)); -#35776=FACE_OUTER_BOUND('',#35775,.F.); -#35778=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,3.156249713898E0)); -#35779=DIRECTION('',(6.611506194509E-1,0.E0,7.502531961943E-1)); -#35780=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#35781=AXIS2_PLACEMENT_3D('',#35778,#35779,#35780); -#35782=PLANE('',#35781); -#35783=ORIENTED_EDGE('',*,*,#26586,.F.); -#35785=ORIENTED_EDGE('',*,*,#35784,.T.); -#35786=ORIENTED_EDGE('',*,*,#28597,.T.); -#35787=ORIENTED_EDGE('',*,*,#35771,.F.); -#35788=EDGE_LOOP('',(#35783,#35785,#35786,#35787)); -#35789=FACE_OUTER_BOUND('',#35788,.F.); -#35791=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,3.212499713898E0)); -#35792=DIRECTION('',(9.353258264754E-1,0.E0,3.537875044826E-1)); -#35793=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#35794=AXIS2_PLACEMENT_3D('',#35791,#35792,#35793); -#35795=PLANE('',#35794); -#35796=ORIENTED_EDGE('',*,*,#26584,.F.); -#35797=ORIENTED_EDGE('',*,*,#35682,.T.); -#35798=ORIENTED_EDGE('',*,*,#28599,.T.); -#35799=ORIENTED_EDGE('',*,*,#35784,.F.); -#35800=EDGE_LOOP('',(#35796,#35797,#35798,#35799)); -#35801=FACE_OUTER_BOUND('',#35800,.F.); -#35803=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,3.099999713898E0)); -#35804=DIRECTION('',(0.E0,0.E0,1.E0)); -#35805=DIRECTION('',(1.E0,0.E0,0.E0)); -#35806=AXIS2_PLACEMENT_3D('',#35803,#35804,#35805); -#35807=PLANE('',#35806); -#35808=ORIENTED_EDGE('',*,*,#26610,.F.); -#35810=ORIENTED_EDGE('',*,*,#35809,.T.); -#35811=ORIENTED_EDGE('',*,*,#28603,.T.); -#35813=ORIENTED_EDGE('',*,*,#35812,.F.); -#35814=EDGE_LOOP('',(#35808,#35810,#35811,#35813)); -#35815=FACE_OUTER_BOUND('',#35814,.F.); -#35817=CARTESIAN_POINT('',(3.617021262646E0,1.55E0,3.118750286102E0)); -#35818=DIRECTION('',(2.818494771324E-1,0.E0,9.594586349813E-1)); -#35819=DIRECTION('',(9.594586349813E-1,0.E0,-2.818494771324E-1)); -#35820=AXIS2_PLACEMENT_3D('',#35817,#35818,#35819); -#35821=PLANE('',#35820); -#35822=ORIENTED_EDGE('',*,*,#26628,.F.); -#35824=ORIENTED_EDGE('',*,*,#35823,.T.); -#35825=ORIENTED_EDGE('',*,*,#28605,.T.); -#35826=ORIENTED_EDGE('',*,*,#35809,.F.); -#35827=EDGE_LOOP('',(#35822,#35824,#35825,#35826)); -#35828=FACE_OUTER_BOUND('',#35827,.F.); -#35830=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,3.156249713898E0)); -#35831=DIRECTION('',(6.611506194509E-1,0.E0,7.502531961943E-1)); -#35832=DIRECTION('',(7.502531961943E-1,0.E0,-6.611506194509E-1)); -#35833=AXIS2_PLACEMENT_3D('',#35830,#35831,#35832); -#35834=PLANE('',#35833); -#35835=ORIENTED_EDGE('',*,*,#26626,.F.); -#35837=ORIENTED_EDGE('',*,*,#35836,.T.); -#35838=ORIENTED_EDGE('',*,*,#28607,.T.); -#35839=ORIENTED_EDGE('',*,*,#35823,.F.); -#35840=EDGE_LOOP('',(#35835,#35837,#35838,#35839)); -#35841=FACE_OUTER_BOUND('',#35840,.F.); -#35843=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.212499713898E0)); -#35844=DIRECTION('',(9.353258264754E-1,0.E0,3.537875044826E-1)); -#35845=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#35846=AXIS2_PLACEMENT_3D('',#35843,#35844,#35845); -#35847=PLANE('',#35846); -#35848=ORIENTED_EDGE('',*,*,#26624,.F.); -#35850=ORIENTED_EDGE('',*,*,#35849,.T.); -#35851=ORIENTED_EDGE('',*,*,#28609,.T.); -#35852=ORIENTED_EDGE('',*,*,#35836,.F.); -#35853=EDGE_LOOP('',(#35848,#35850,#35851,#35852)); -#35854=FACE_OUTER_BOUND('',#35853,.F.); -#35856=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,3.568749856949E0)); -#35857=DIRECTION('',(1.E0,0.E0,0.E0)); -#35858=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35859=AXIS2_PLACEMENT_3D('',#35856,#35857,#35858); -#35860=PLANE('',#35859); -#35861=ORIENTED_EDGE('',*,*,#26622,.F.); -#35863=ORIENTED_EDGE('',*,*,#35862,.T.); -#35864=ORIENTED_EDGE('',*,*,#28611,.T.); -#35865=ORIENTED_EDGE('',*,*,#35849,.F.); -#35866=EDGE_LOOP('',(#35861,#35863,#35864,#35865)); -#35867=FACE_OUTER_BOUND('',#35866,.F.); -#35869=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.568749856949E0)); -#35870=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35871=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35872=AXIS2_PLACEMENT_3D('',#35869,#35870,#35871); -#35873=PLANE('',#35872); -#35874=ORIENTED_EDGE('',*,*,#26620,.F.); -#35876=ORIENTED_EDGE('',*,*,#35875,.T.); -#35877=ORIENTED_EDGE('',*,*,#28613,.T.); -#35878=ORIENTED_EDGE('',*,*,#35862,.F.); -#35879=EDGE_LOOP('',(#35874,#35876,#35877,#35878)); -#35880=FACE_OUTER_BOUND('',#35879,.F.); -#35882=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,3.212499713898E0)); -#35883=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35884=DIRECTION('',(0.E0,0.E0,1.E0)); -#35885=AXIS2_PLACEMENT_3D('',#35882,#35883,#35884); -#35886=PLANE('',#35885); -#35887=ORIENTED_EDGE('',*,*,#26618,.F.); -#35889=ORIENTED_EDGE('',*,*,#35888,.T.); -#35890=ORIENTED_EDGE('',*,*,#28615,.T.); -#35891=ORIENTED_EDGE('',*,*,#35875,.F.); -#35892=EDGE_LOOP('',(#35887,#35889,#35890,#35891)); -#35893=FACE_OUTER_BOUND('',#35892,.F.); -#35895=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,3.156249713898E0)); -#35896=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#35897=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#35898=AXIS2_PLACEMENT_3D('',#35895,#35896,#35897); -#35899=PLANE('',#35898); -#35900=ORIENTED_EDGE('',*,*,#26616,.F.); -#35902=ORIENTED_EDGE('',*,*,#35901,.T.); -#35903=ORIENTED_EDGE('',*,*,#28617,.T.); -#35904=ORIENTED_EDGE('',*,*,#35888,.F.); -#35905=EDGE_LOOP('',(#35900,#35902,#35903,#35904)); -#35906=FACE_OUTER_BOUND('',#35905,.F.); -#35908=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,3.118750286102E0)); -#35909=DIRECTION('',(-6.611504891330E-1,0.E0,7.502533110351E-1)); -#35910=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#35911=AXIS2_PLACEMENT_3D('',#35908,#35909,#35910); -#35912=PLANE('',#35911); -#35913=ORIENTED_EDGE('',*,*,#26614,.F.); -#35915=ORIENTED_EDGE('',*,*,#35914,.T.); -#35916=ORIENTED_EDGE('',*,*,#28619,.T.); -#35917=ORIENTED_EDGE('',*,*,#35901,.F.); -#35918=EDGE_LOOP('',(#35913,#35915,#35916,#35917)); -#35919=FACE_OUTER_BOUND('',#35918,.F.); -#35921=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,3.099999713898E0)); -#35922=DIRECTION('',(-2.818495982749E-1,0.E0,9.594585993946E-1)); -#35923=DIRECTION('',(9.594585993946E-1,0.E0,2.818495982749E-1)); -#35924=AXIS2_PLACEMENT_3D('',#35921,#35922,#35923); -#35925=PLANE('',#35924); -#35926=ORIENTED_EDGE('',*,*,#26612,.F.); -#35927=ORIENTED_EDGE('',*,*,#35812,.T.); -#35928=ORIENTED_EDGE('',*,*,#28621,.T.); -#35929=ORIENTED_EDGE('',*,*,#35914,.F.); -#35930=EDGE_LOOP('',(#35926,#35927,#35928,#35929)); -#35931=FACE_OUTER_BOUND('',#35930,.F.); -#35933=CARTESIAN_POINT('',(3.E0,1.55E0,2.125E0)); -#35934=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35935=DIRECTION('',(0.E0,0.E0,1.E0)); -#35936=AXIS2_PLACEMENT_3D('',#35933,#35934,#35935); -#35937=PLANE('',#35936); -#35938=ORIENTED_EDGE('',*,*,#25318,.F.); -#35940=ORIENTED_EDGE('',*,*,#35939,.T.); -#35941=ORIENTED_EDGE('',*,*,#28638,.T.); -#35943=ORIENTED_EDGE('',*,*,#35942,.F.); -#35944=EDGE_LOOP('',(#35938,#35940,#35941,#35943)); -#35945=FACE_OUTER_BOUND('',#35944,.F.); -#35947=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.125E0)); -#35948=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35949=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35950=AXIS2_PLACEMENT_3D('',#35947,#35948,#35949); -#35951=PLANE('',#35950); -#35952=ORIENTED_EDGE('',*,*,#25332,.F.); -#35954=ORIENTED_EDGE('',*,*,#35953,.T.); -#35955=ORIENTED_EDGE('',*,*,#28640,.T.); -#35956=ORIENTED_EDGE('',*,*,#35939,.F.); -#35957=EDGE_LOOP('',(#35952,#35954,#35955,#35956)); -#35958=FACE_OUTER_BOUND('',#35957,.F.); -#35960=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.424999713898E0)); -#35961=DIRECTION('',(1.E0,0.E0,0.E0)); -#35962=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35963=AXIS2_PLACEMENT_3D('',#35960,#35961,#35962); -#35964=PLANE('',#35963); -#35965=ORIENTED_EDGE('',*,*,#25330,.F.); -#35967=ORIENTED_EDGE('',*,*,#35966,.T.); -#35968=ORIENTED_EDGE('',*,*,#28642,.T.); -#35969=ORIENTED_EDGE('',*,*,#35953,.F.); -#35970=EDGE_LOOP('',(#35965,#35967,#35968,#35969)); -#35971=FACE_OUTER_BOUND('',#35970,.F.); -#35973=CARTESIAN_POINT('',(4.E0,1.55E0,2.424999713898E0)); -#35974=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35975=DIRECTION('',(-1.E0,0.E0,0.E0)); -#35976=AXIS2_PLACEMENT_3D('',#35973,#35974,#35975); -#35977=PLANE('',#35976); -#35978=ORIENTED_EDGE('',*,*,#25328,.F.); -#35980=ORIENTED_EDGE('',*,*,#35979,.T.); -#35981=ORIENTED_EDGE('',*,*,#28644,.T.); -#35982=ORIENTED_EDGE('',*,*,#35966,.F.); -#35983=EDGE_LOOP('',(#35978,#35980,#35981,#35982)); -#35984=FACE_OUTER_BOUND('',#35983,.F.); -#35986=CARTESIAN_POINT('',(4.E0,1.55E0,2.537499713898E0)); -#35987=DIRECTION('',(1.E0,0.E0,0.E0)); -#35988=DIRECTION('',(0.E0,0.E0,-1.E0)); -#35989=AXIS2_PLACEMENT_3D('',#35986,#35987,#35988); -#35990=PLANE('',#35989); -#35991=ORIENTED_EDGE('',*,*,#25326,.F.); -#35993=ORIENTED_EDGE('',*,*,#35992,.T.); -#35994=ORIENTED_EDGE('',*,*,#28646,.T.); -#35995=ORIENTED_EDGE('',*,*,#35979,.F.); -#35996=EDGE_LOOP('',(#35991,#35993,#35994,#35995)); -#35997=FACE_OUTER_BOUND('',#35996,.F.); -#35999=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.537499713898E0)); -#36000=DIRECTION('',(0.E0,0.E0,1.E0)); -#36001=DIRECTION('',(1.E0,0.E0,0.E0)); -#36002=AXIS2_PLACEMENT_3D('',#35999,#36000,#36001); -#36003=PLANE('',#36002); -#36004=ORIENTED_EDGE('',*,*,#25324,.F.); -#36006=ORIENTED_EDGE('',*,*,#36005,.T.); -#36007=ORIENTED_EDGE('',*,*,#28648,.T.); -#36008=ORIENTED_EDGE('',*,*,#35992,.F.); -#36009=EDGE_LOOP('',(#36004,#36006,#36007,#36008)); -#36010=FACE_OUTER_BOUND('',#36009,.F.); -#36012=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.837500286102E0)); -#36013=DIRECTION('',(1.E0,0.E0,0.E0)); -#36014=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36015=AXIS2_PLACEMENT_3D('',#36012,#36013,#36014); -#36016=PLANE('',#36015); -#36017=ORIENTED_EDGE('',*,*,#25322,.F.); -#36019=ORIENTED_EDGE('',*,*,#36018,.T.); -#36020=ORIENTED_EDGE('',*,*,#28650,.T.); -#36021=ORIENTED_EDGE('',*,*,#36005,.F.); -#36022=EDGE_LOOP('',(#36017,#36019,#36020,#36021)); -#36023=FACE_OUTER_BOUND('',#36022,.F.); -#36025=CARTESIAN_POINT('',(3.E0,1.55E0,2.837500286102E0)); -#36026=DIRECTION('',(0.E0,0.E0,1.E0)); -#36027=DIRECTION('',(1.E0,0.E0,0.E0)); -#36028=AXIS2_PLACEMENT_3D('',#36025,#36026,#36027); -#36029=PLANE('',#36028); -#36030=ORIENTED_EDGE('',*,*,#25320,.F.); -#36031=ORIENTED_EDGE('',*,*,#35942,.T.); -#36032=ORIENTED_EDGE('',*,*,#28652,.T.); -#36033=ORIENTED_EDGE('',*,*,#36018,.F.); -#36034=EDGE_LOOP('',(#36030,#36031,#36032,#36033)); -#36035=FACE_OUTER_BOUND('',#36034,.F.); -#36037=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.825000286102E0)); -#36038=DIRECTION('',(-8.697542675479E-1,0.E0,4.934850697662E-1)); -#36039=DIRECTION('',(4.934850697662E-1,0.E0,8.697542675479E-1)); -#36040=AXIS2_PLACEMENT_3D('',#36037,#36038,#36039); -#36041=PLANE('',#36040); -#36042=ORIENTED_EDGE('',*,*,#25336,.F.); -#36044=ORIENTED_EDGE('',*,*,#36043,.T.); -#36045=ORIENTED_EDGE('',*,*,#28669,.T.); -#36047=ORIENTED_EDGE('',*,*,#36046,.F.); -#36048=EDGE_LOOP('',(#36042,#36044,#36045,#36047)); -#36049=FACE_OUTER_BOUND('',#36048,.F.); -#36051=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.862499713898E0)); -#36052=DIRECTION('',(8.697542675479E-1,0.E0,4.934850697662E-1)); -#36053=DIRECTION('',(4.934850697662E-1,0.E0,-8.697542675479E-1)); -#36054=AXIS2_PLACEMENT_3D('',#36051,#36052,#36053); -#36055=PLANE('',#36054); -#36056=ORIENTED_EDGE('',*,*,#25402,.F.); -#36058=ORIENTED_EDGE('',*,*,#36057,.T.); -#36059=ORIENTED_EDGE('',*,*,#28671,.T.); -#36060=ORIENTED_EDGE('',*,*,#36043,.F.); -#36061=EDGE_LOOP('',(#36056,#36058,#36059,#36060)); -#36062=FACE_OUTER_BOUND('',#36061,.F.); -#36064=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.918749713898E0)); -#36065=DIRECTION('',(6.611562980142E-1,0.E0,7.502481919980E-1)); -#36066=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#36067=AXIS2_PLACEMENT_3D('',#36064,#36065,#36066); -#36068=PLANE('',#36067); -#36069=ORIENTED_EDGE('',*,*,#25400,.F.); -#36071=ORIENTED_EDGE('',*,*,#36070,.T.); -#36072=ORIENTED_EDGE('',*,*,#28673,.T.); -#36073=ORIENTED_EDGE('',*,*,#36057,.F.); -#36074=EDGE_LOOP('',(#36069,#36071,#36072,#36073)); -#36075=FACE_OUTER_BOUND('',#36074,.F.); -#36077=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.95625E0)); -#36078=DIRECTION('',(4.032203477633E-1,0.E0,9.151029183374E-1)); -#36079=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#36080=AXIS2_PLACEMENT_3D('',#36077,#36078,#36079); -#36081=PLANE('',#36080); -#36082=ORIENTED_EDGE('',*,*,#25398,.F.); -#36084=ORIENTED_EDGE('',*,*,#36083,.T.); -#36085=ORIENTED_EDGE('',*,*,#28675,.T.); -#36086=ORIENTED_EDGE('',*,*,#36070,.F.); -#36087=EDGE_LOOP('',(#36082,#36084,#36085,#36086)); -#36088=FACE_OUTER_BOUND('',#36087,.F.); -#36090=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.95625E0)); -#36091=DIRECTION('',(0.E0,0.E0,1.E0)); -#36092=DIRECTION('',(1.E0,0.E0,0.E0)); -#36093=AXIS2_PLACEMENT_3D('',#36090,#36091,#36092); -#36094=PLANE('',#36093); -#36095=ORIENTED_EDGE('',*,*,#25396,.F.); -#36097=ORIENTED_EDGE('',*,*,#36096,.T.); -#36098=ORIENTED_EDGE('',*,*,#28677,.T.); -#36099=ORIENTED_EDGE('',*,*,#36083,.F.); -#36100=EDGE_LOOP('',(#36095,#36097,#36098,#36099)); -#36101=FACE_OUTER_BOUND('',#36100,.F.); -#36103=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.918749713898E0)); -#36104=DIRECTION('',(-3.324522241845E-1,0.E0,9.431200976730E-1)); -#36105=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#36106=AXIS2_PLACEMENT_3D('',#36103,#36104,#36105); -#36107=PLANE('',#36106); -#36108=ORIENTED_EDGE('',*,*,#25394,.F.); -#36110=ORIENTED_EDGE('',*,*,#36109,.T.); -#36111=ORIENTED_EDGE('',*,*,#28679,.T.); -#36112=ORIENTED_EDGE('',*,*,#36096,.F.); -#36113=EDGE_LOOP('',(#36108,#36110,#36111,#36112)); -#36114=FACE_OUTER_BOUND('',#36113,.F.); -#36116=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.862499713898E0)); -#36117=DIRECTION('',(-6.611562980142E-1,0.E0,7.502481919980E-1)); -#36118=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#36119=AXIS2_PLACEMENT_3D('',#36116,#36117,#36118); -#36120=PLANE('',#36119); -#36121=ORIENTED_EDGE('',*,*,#25392,.F.); -#36123=ORIENTED_EDGE('',*,*,#36122,.T.); -#36124=ORIENTED_EDGE('',*,*,#28681,.T.); -#36125=ORIENTED_EDGE('',*,*,#36109,.F.); -#36126=EDGE_LOOP('',(#36121,#36123,#36124,#36125)); -#36127=FACE_OUTER_BOUND('',#36126,.F.); -#36129=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.768750286102E0)); -#36130=DIRECTION('',(-8.265976808173E-1,0.E0,5.627932782715E-1)); -#36131=DIRECTION('',(5.627932782715E-1,0.E0,8.265976808173E-1)); -#36132=AXIS2_PLACEMENT_3D('',#36129,#36130,#36131); -#36133=PLANE('',#36132); -#36134=ORIENTED_EDGE('',*,*,#25390,.F.); -#36136=ORIENTED_EDGE('',*,*,#36135,.T.); -#36137=ORIENTED_EDGE('',*,*,#28683,.T.); -#36138=ORIENTED_EDGE('',*,*,#36122,.F.); -#36139=EDGE_LOOP('',(#36134,#36136,#36137,#36138)); -#36140=FACE_OUTER_BOUND('',#36139,.F.); -#36142=CARTESIAN_POINT('',(3.E0,1.55E0,1.675E0)); -#36143=DIRECTION('',(-9.752009016921E-1,0.E0,2.213214886517E-1)); -#36144=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#36145=AXIS2_PLACEMENT_3D('',#36142,#36143,#36144); -#36146=PLANE('',#36145); -#36147=ORIENTED_EDGE('',*,*,#25388,.F.); -#36149=ORIENTED_EDGE('',*,*,#36148,.T.); -#36150=ORIENTED_EDGE('',*,*,#28685,.T.); -#36151=ORIENTED_EDGE('',*,*,#36135,.F.); -#36152=EDGE_LOOP('',(#36147,#36149,#36150,#36151)); -#36153=FACE_OUTER_BOUND('',#36152,.F.); -#36155=CARTESIAN_POINT('',(3.E0,1.55E0,1.600000286102E0)); -#36156=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36157=DIRECTION('',(0.E0,0.E0,1.E0)); -#36158=AXIS2_PLACEMENT_3D('',#36155,#36156,#36157); -#36159=PLANE('',#36158); -#36160=ORIENTED_EDGE('',*,*,#25386,.F.); -#36162=ORIENTED_EDGE('',*,*,#36161,.T.); -#36163=ORIENTED_EDGE('',*,*,#28687,.T.); -#36164=ORIENTED_EDGE('',*,*,#36148,.F.); -#36165=EDGE_LOOP('',(#36160,#36162,#36163,#36164)); -#36166=FACE_OUTER_BOUND('',#36165,.F.); -#36168=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.50625E0)); -#36169=DIRECTION('',(-9.752009016921E-1,0.E0,-2.213214886517E-1)); -#36170=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#36171=AXIS2_PLACEMENT_3D('',#36168,#36169,#36170); -#36172=PLANE('',#36171); -#36173=ORIENTED_EDGE('',*,*,#25384,.F.); -#36175=ORIENTED_EDGE('',*,*,#36174,.T.); -#36176=ORIENTED_EDGE('',*,*,#28689,.T.); -#36177=ORIENTED_EDGE('',*,*,#36161,.F.); -#36178=EDGE_LOOP('',(#36173,#36175,#36176,#36177)); -#36179=FACE_OUTER_BOUND('',#36178,.F.); -#36181=CARTESIAN_POINT('',(3.085106372833E0,1.55E0,1.412499713898E0)); -#36182=DIRECTION('',(-8.266000777833E-1,0.E0,-5.627897577325E-1)); -#36183=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#36184=AXIS2_PLACEMENT_3D('',#36181,#36182,#36183); -#36185=PLANE('',#36184); -#36186=ORIENTED_EDGE('',*,*,#25382,.F.); -#36188=ORIENTED_EDGE('',*,*,#36187,.T.); -#36189=ORIENTED_EDGE('',*,*,#28691,.T.); -#36190=ORIENTED_EDGE('',*,*,#36174,.F.); -#36191=EDGE_LOOP('',(#36186,#36188,#36189,#36190)); -#36192=FACE_OUTER_BOUND('',#36191,.F.); -#36194=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.356249713898E0)); -#36195=DIRECTION('',(-6.611562980142E-1,0.E0,-7.502481919980E-1)); -#36196=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#36197=AXIS2_PLACEMENT_3D('',#36194,#36195,#36196); -#36198=PLANE('',#36197); -#36199=ORIENTED_EDGE('',*,*,#25380,.F.); -#36201=ORIENTED_EDGE('',*,*,#36200,.T.); -#36202=ORIENTED_EDGE('',*,*,#28693,.T.); -#36203=ORIENTED_EDGE('',*,*,#36187,.F.); -#36204=EDGE_LOOP('',(#36199,#36201,#36202,#36203)); -#36205=FACE_OUTER_BOUND('',#36204,.F.); -#36207=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.318750286102E0)); -#36208=DIRECTION('',(-3.324454559889E-1,0.E0,-9.431224834518E-1)); -#36209=DIRECTION('',(-9.431224834518E-1,0.E0,3.324454559889E-1)); -#36210=AXIS2_PLACEMENT_3D('',#36207,#36208,#36209); -#36211=PLANE('',#36210); -#36212=ORIENTED_EDGE('',*,*,#25378,.F.); -#36214=ORIENTED_EDGE('',*,*,#36213,.T.); -#36215=ORIENTED_EDGE('',*,*,#28695,.T.); -#36216=ORIENTED_EDGE('',*,*,#36200,.F.); -#36217=EDGE_LOOP('',(#36212,#36214,#36215,#36216)); -#36218=FACE_OUTER_BOUND('',#36217,.F.); -#36220=CARTESIAN_POINT('',(3.319148957729E0,1.55E0,1.318750286102E0)); -#36221=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36222=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36223=AXIS2_PLACEMENT_3D('',#36220,#36221,#36222); -#36224=PLANE('',#36223); -#36225=ORIENTED_EDGE('',*,*,#25376,.F.); -#36227=ORIENTED_EDGE('',*,*,#36226,.T.); -#36228=ORIENTED_EDGE('',*,*,#28697,.T.); -#36229=ORIENTED_EDGE('',*,*,#36213,.F.); -#36230=EDGE_LOOP('',(#36225,#36227,#36228,#36229)); -#36231=FACE_OUTER_BOUND('',#36230,.F.); -#36233=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,1.356249713898E0)); -#36234=DIRECTION('',(4.032126193069E-1,0.E0,-9.151063236759E-1)); -#36235=DIRECTION('',(-9.151063236759E-1,0.E0,-4.032126193069E-1)); -#36236=AXIS2_PLACEMENT_3D('',#36233,#36234,#36235); -#36237=PLANE('',#36236); -#36238=ORIENTED_EDGE('',*,*,#25374,.F.); -#36240=ORIENTED_EDGE('',*,*,#36239,.T.); -#36241=ORIENTED_EDGE('',*,*,#28699,.T.); -#36242=ORIENTED_EDGE('',*,*,#36226,.F.); -#36243=EDGE_LOOP('',(#36238,#36240,#36241,#36242)); -#36244=FACE_OUTER_BOUND('',#36243,.F.); -#36246=CARTESIAN_POINT('',(3.468085110188E0,1.55E0,1.412499713898E0)); -#36247=DIRECTION('',(6.611562980142E-1,0.E0,-7.502481919980E-1)); -#36248=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#36249=AXIS2_PLACEMENT_3D('',#36246,#36247,#36248); -#36250=PLANE('',#36249); -#36251=ORIENTED_EDGE('',*,*,#25372,.F.); -#36253=ORIENTED_EDGE('',*,*,#36252,.T.); -#36254=ORIENTED_EDGE('',*,*,#28701,.T.); -#36255=ORIENTED_EDGE('',*,*,#36239,.F.); -#36256=EDGE_LOOP('',(#36251,#36253,#36254,#36255)); -#36257=FACE_OUTER_BOUND('',#36256,.F.); -#36259=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,1.45E0)); -#36260=DIRECTION('',(8.697591154214E-1,0.E0,-4.934765254207E-1)); -#36261=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#36262=AXIS2_PLACEMENT_3D('',#36259,#36260,#36261); -#36263=PLANE('',#36262); -#36264=ORIENTED_EDGE('',*,*,#25370,.F.); -#36266=ORIENTED_EDGE('',*,*,#36265,.T.); -#36267=ORIENTED_EDGE('',*,*,#28703,.T.); -#36268=ORIENTED_EDGE('',*,*,#36252,.F.); -#36269=EDGE_LOOP('',(#36264,#36266,#36267,#36268)); -#36270=FACE_OUTER_BOUND('',#36269,.F.); -#36272=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.412499713898E0)); -#36273=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#36274=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#36275=AXIS2_PLACEMENT_3D('',#36272,#36273,#36274); -#36276=PLANE('',#36275); -#36277=ORIENTED_EDGE('',*,*,#25368,.F.); -#36279=ORIENTED_EDGE('',*,*,#36278,.T.); -#36280=ORIENTED_EDGE('',*,*,#28705,.T.); -#36281=ORIENTED_EDGE('',*,*,#36265,.F.); -#36282=EDGE_LOOP('',(#36277,#36279,#36280,#36281)); -#36283=FACE_OUTER_BOUND('',#36282,.F.); -#36285=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.3375E0)); -#36286=DIRECTION('',(-7.615382075403E-1,0.E0,-6.481200185586E-1)); -#36287=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#36288=AXIS2_PLACEMENT_3D('',#36285,#36286,#36287); -#36289=PLANE('',#36288); -#36290=ORIENTED_EDGE('',*,*,#25366,.F.); -#36292=ORIENTED_EDGE('',*,*,#36291,.T.); -#36293=ORIENTED_EDGE('',*,*,#28707,.T.); -#36294=ORIENTED_EDGE('',*,*,#36278,.F.); -#36295=EDGE_LOOP('',(#36290,#36292,#36293,#36294)); -#36296=FACE_OUTER_BOUND('',#36295,.F.); -#36298=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.299999713898E0)); -#36299=DIRECTION('',(-3.324523070247E-1,0.E0,-9.431200684716E-1)); -#36300=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#36301=AXIS2_PLACEMENT_3D('',#36298,#36299,#36300); -#36302=PLANE('',#36301); -#36303=ORIENTED_EDGE('',*,*,#25364,.F.); -#36305=ORIENTED_EDGE('',*,*,#36304,.T.); -#36306=ORIENTED_EDGE('',*,*,#28709,.T.); -#36307=ORIENTED_EDGE('',*,*,#36291,.F.); -#36308=EDGE_LOOP('',(#36303,#36305,#36306,#36307)); -#36309=FACE_OUTER_BOUND('',#36308,.F.); -#36311=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.299999713898E0)); -#36312=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36313=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36314=AXIS2_PLACEMENT_3D('',#36311,#36312,#36313); -#36315=PLANE('',#36314); -#36316=ORIENTED_EDGE('',*,*,#25362,.F.); -#36318=ORIENTED_EDGE('',*,*,#36317,.T.); -#36319=ORIENTED_EDGE('',*,*,#28711,.T.); -#36320=ORIENTED_EDGE('',*,*,#36304,.F.); -#36321=EDGE_LOOP('',(#36316,#36318,#36319,#36320)); -#36322=FACE_OUTER_BOUND('',#36321,.F.); -#36324=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.3375E0)); -#36325=DIRECTION('',(3.324523484448E-1,0.E0,-9.431200538709E-1)); -#36326=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#36327=AXIS2_PLACEMENT_3D('',#36324,#36325,#36326); -#36328=PLANE('',#36327); -#36329=ORIENTED_EDGE('',*,*,#25360,.F.); -#36331=ORIENTED_EDGE('',*,*,#36330,.T.); -#36332=ORIENTED_EDGE('',*,*,#28713,.T.); -#36333=ORIENTED_EDGE('',*,*,#36317,.F.); -#36334=EDGE_LOOP('',(#36329,#36331,#36332,#36333)); -#36335=FACE_OUTER_BOUND('',#36334,.F.); -#36337=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.39375E0)); -#36338=DIRECTION('',(6.611562545751E-1,0.E0,-7.502482302787E-1)); -#36339=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#36340=AXIS2_PLACEMENT_3D('',#36337,#36338,#36339); -#36341=PLANE('',#36340); -#36342=ORIENTED_EDGE('',*,*,#25358,.F.); -#36344=ORIENTED_EDGE('',*,*,#36343,.T.); -#36345=ORIENTED_EDGE('',*,*,#28715,.T.); -#36346=ORIENTED_EDGE('',*,*,#36330,.F.); -#36347=EDGE_LOOP('',(#36342,#36344,#36345,#36346)); -#36348=FACE_OUTER_BOUND('',#36347,.F.); -#36350=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.487500286102E0)); -#36351=DIRECTION('',(8.266000548632E-1,0.E0,-5.627897913965E-1)); -#36352=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#36353=AXIS2_PLACEMENT_3D('',#36350,#36351,#36352); -#36354=PLANE('',#36353); -#36355=ORIENTED_EDGE('',*,*,#25356,.F.); -#36357=ORIENTED_EDGE('',*,*,#36356,.T.); -#36358=ORIENTED_EDGE('',*,*,#28717,.T.); -#36359=ORIENTED_EDGE('',*,*,#36343,.F.); -#36360=EDGE_LOOP('',(#36355,#36357,#36358,#36359)); -#36361=FACE_OUTER_BOUND('',#36360,.F.); -#36363=CARTESIAN_POINT('',(4.E0,1.55E0,1.581249713898E0)); -#36364=DIRECTION('',(9.752004601724E-1,0.E0,-2.213234340948E-1)); -#36365=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#36366=AXIS2_PLACEMENT_3D('',#36363,#36364,#36365); -#36367=PLANE('',#36366); -#36368=ORIENTED_EDGE('',*,*,#25354,.F.); -#36370=ORIENTED_EDGE('',*,*,#36369,.T.); -#36371=ORIENTED_EDGE('',*,*,#28719,.T.); -#36372=ORIENTED_EDGE('',*,*,#36356,.F.); -#36373=EDGE_LOOP('',(#36368,#36370,#36371,#36372)); -#36374=FACE_OUTER_BOUND('',#36373,.F.); -#36376=CARTESIAN_POINT('',(4.E0,1.55E0,1.693749713898E0)); -#36377=DIRECTION('',(1.E0,0.E0,0.E0)); -#36378=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36379=AXIS2_PLACEMENT_3D('',#36376,#36377,#36378); -#36380=PLANE('',#36379); -#36381=ORIENTED_EDGE('',*,*,#25352,.F.); -#36383=ORIENTED_EDGE('',*,*,#36382,.T.); -#36384=ORIENTED_EDGE('',*,*,#28721,.T.); -#36385=ORIENTED_EDGE('',*,*,#36369,.F.); -#36386=EDGE_LOOP('',(#36381,#36383,#36384,#36385)); -#36387=FACE_OUTER_BOUND('',#36386,.F.); -#36389=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,1.7875E0)); -#36390=DIRECTION('',(9.752008975102E-1,0.E0,2.213215070781E-1)); -#36391=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#36392=AXIS2_PLACEMENT_3D('',#36389,#36390,#36391); -#36393=PLANE('',#36392); -#36394=ORIENTED_EDGE('',*,*,#25350,.F.); -#36396=ORIENTED_EDGE('',*,*,#36395,.T.); -#36397=ORIENTED_EDGE('',*,*,#28723,.T.); -#36398=ORIENTED_EDGE('',*,*,#36382,.F.); -#36399=EDGE_LOOP('',(#36394,#36396,#36397,#36398)); -#36400=FACE_OUTER_BOUND('',#36399,.F.); -#36402=CARTESIAN_POINT('',(3.914893619716E0,1.55E0,1.881250286102E0)); -#36403=DIRECTION('',(8.266000548632E-1,0.E0,5.627897913965E-1)); -#36404=DIRECTION('',(5.627897913965E-1,0.E0,-8.266000548632E-1)); -#36405=AXIS2_PLACEMENT_3D('',#36402,#36403,#36404); -#36406=PLANE('',#36405); -#36407=ORIENTED_EDGE('',*,*,#25348,.F.); -#36409=ORIENTED_EDGE('',*,*,#36408,.T.); -#36410=ORIENTED_EDGE('',*,*,#28725,.T.); -#36411=ORIENTED_EDGE('',*,*,#36395,.F.); -#36412=EDGE_LOOP('',(#36407,#36409,#36410,#36411)); -#36413=FACE_OUTER_BOUND('',#36412,.F.); -#36415=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.937500286102E0)); -#36416=DIRECTION('',(6.611562545751E-1,0.E0,7.502482302787E-1)); -#36417=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#36418=AXIS2_PLACEMENT_3D('',#36415,#36416,#36417); -#36419=PLANE('',#36418); -#36420=ORIENTED_EDGE('',*,*,#25346,.F.); -#36422=ORIENTED_EDGE('',*,*,#36421,.T.); -#36423=ORIENTED_EDGE('',*,*,#28727,.T.); -#36424=ORIENTED_EDGE('',*,*,#36408,.F.); -#36425=EDGE_LOOP('',(#36420,#36422,#36423,#36424)); -#36426=FACE_OUTER_BOUND('',#36425,.F.); -#36428=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.974999713898E0)); -#36429=DIRECTION('',(3.324455802473E-1,0.E0,9.431224396514E-1)); -#36430=DIRECTION('',(9.431224396514E-1,0.E0,-3.324455802473E-1)); -#36431=AXIS2_PLACEMENT_3D('',#36428,#36429,#36430); -#36432=PLANE('',#36431); -#36433=ORIENTED_EDGE('',*,*,#25344,.F.); -#36435=ORIENTED_EDGE('',*,*,#36434,.T.); -#36436=ORIENTED_EDGE('',*,*,#28729,.T.); -#36437=ORIENTED_EDGE('',*,*,#36421,.F.); -#36438=EDGE_LOOP('',(#36433,#36435,#36436,#36437)); -#36439=FACE_OUTER_BOUND('',#36438,.F.); -#36441=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.974999713898E0)); -#36442=DIRECTION('',(0.E0,0.E0,1.E0)); -#36443=DIRECTION('',(1.E0,0.E0,0.E0)); -#36444=AXIS2_PLACEMENT_3D('',#36441,#36442,#36443); -#36445=PLANE('',#36444); -#36446=ORIENTED_EDGE('',*,*,#25342,.F.); -#36448=ORIENTED_EDGE('',*,*,#36447,.T.); -#36449=ORIENTED_EDGE('',*,*,#28731,.T.); -#36450=ORIENTED_EDGE('',*,*,#36434,.F.); -#36451=EDGE_LOOP('',(#36446,#36448,#36449,#36450)); -#36452=FACE_OUTER_BOUND('',#36451,.F.); -#36454=CARTESIAN_POINT('',(3.574468076229E0,1.55E0,1.937500286102E0)); -#36455=DIRECTION('',(-3.324455388278E-1,0.E0,9.431224542516E-1)); -#36456=DIRECTION('',(9.431224542516E-1,0.E0,3.324455388278E-1)); -#36457=AXIS2_PLACEMENT_3D('',#36454,#36455,#36456); -#36458=PLANE('',#36457); -#36459=ORIENTED_EDGE('',*,*,#25340,.F.); -#36461=ORIENTED_EDGE('',*,*,#36460,.T.); -#36462=ORIENTED_EDGE('',*,*,#28733,.T.); -#36463=ORIENTED_EDGE('',*,*,#36447,.F.); -#36464=EDGE_LOOP('',(#36459,#36461,#36462,#36463)); -#36465=FACE_OUTER_BOUND('',#36464,.F.); -#36467=CARTESIAN_POINT('',(3.510638296604E0,1.55E0,1.862499713898E0)); -#36468=DIRECTION('',(-7.615418683844E-1,0.E0,6.481157170580E-1)); -#36469=DIRECTION('',(6.481157170580E-1,0.E0,7.615418683844E-1)); -#36470=AXIS2_PLACEMENT_3D('',#36467,#36468,#36469); -#36471=PLANE('',#36470); -#36472=ORIENTED_EDGE('',*,*,#25338,.F.); -#36473=ORIENTED_EDGE('',*,*,#36046,.T.); -#36474=ORIENTED_EDGE('',*,*,#28735,.T.); -#36475=ORIENTED_EDGE('',*,*,#36460,.F.); -#36476=EDGE_LOOP('',(#36472,#36473,#36474,#36475)); -#36477=FACE_OUTER_BOUND('',#36476,.F.); -#36479=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.675E0)); -#36480=DIRECTION('',(-9.620369340052E-1,0.E0,-2.729192877205E-1)); -#36481=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#36482=AXIS2_PLACEMENT_3D('',#36479,#36480,#36481); -#36483=PLANE('',#36482); -#36484=ORIENTED_EDGE('',*,*,#26638,.F.); -#36486=ORIENTED_EDGE('',*,*,#36485,.T.); -#36487=ORIENTED_EDGE('',*,*,#28739,.T.); -#36489=ORIENTED_EDGE('',*,*,#36488,.F.); -#36490=EDGE_LOOP('',(#36484,#36486,#36487,#36489)); -#36491=FACE_OUTER_BOUND('',#36490,.F.); -#36493=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.600000286102E0)); -#36494=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36495=DIRECTION('',(0.E0,0.E0,1.E0)); -#36496=AXIS2_PLACEMENT_3D('',#36493,#36494,#36495); -#36497=PLANE('',#36496); -#36498=ORIENTED_EDGE('',*,*,#26668,.F.); -#36500=ORIENTED_EDGE('',*,*,#36499,.T.); -#36501=ORIENTED_EDGE('',*,*,#28741,.T.); -#36502=ORIENTED_EDGE('',*,*,#36485,.F.); -#36503=EDGE_LOOP('',(#36498,#36500,#36501,#36502)); -#36504=FACE_OUTER_BOUND('',#36503,.F.); -#36506=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.524999713898E0)); -#36507=DIRECTION('',(-9.620377540476E-1,0.E0,2.729163970653E-1)); -#36508=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#36509=AXIS2_PLACEMENT_3D('',#36506,#36507,#36508); -#36510=PLANE('',#36509); -#36511=ORIENTED_EDGE('',*,*,#26666,.F.); -#36513=ORIENTED_EDGE('',*,*,#36512,.T.); -#36514=ORIENTED_EDGE('',*,*,#28743,.T.); -#36515=ORIENTED_EDGE('',*,*,#36499,.F.); -#36516=EDGE_LOOP('',(#36511,#36513,#36514,#36515)); -#36517=FACE_OUTER_BOUND('',#36516,.F.); -#36519=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.45E0)); -#36520=DIRECTION('',(-8.697566915162E-1,0.E0,4.934807975624E-1)); -#36521=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#36522=AXIS2_PLACEMENT_3D('',#36519,#36520,#36521); -#36523=PLANE('',#36522); -#36524=ORIENTED_EDGE('',*,*,#26664,.F.); -#36526=ORIENTED_EDGE('',*,*,#36525,.T.); -#36527=ORIENTED_EDGE('',*,*,#28745,.T.); -#36528=ORIENTED_EDGE('',*,*,#36512,.F.); -#36529=EDGE_LOOP('',(#36524,#36526,#36527,#36528)); -#36530=FACE_OUTER_BOUND('',#36529,.F.); -#36532=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.39375E0)); -#36533=DIRECTION('',(-5.513868654785E-1,0.E0,8.342496776013E-1)); -#36534=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#36535=AXIS2_PLACEMENT_3D('',#36532,#36533,#36534); -#36536=PLANE('',#36535); -#36537=ORIENTED_EDGE('',*,*,#26662,.F.); -#36539=ORIENTED_EDGE('',*,*,#36538,.T.); -#36540=ORIENTED_EDGE('',*,*,#28747,.T.); -#36541=ORIENTED_EDGE('',*,*,#36525,.F.); -#36542=EDGE_LOOP('',(#36537,#36539,#36540,#36541)); -#36543=FACE_OUTER_BOUND('',#36542,.F.); -#36545=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.39375E0)); -#36546=DIRECTION('',(0.E0,0.E0,1.E0)); -#36547=DIRECTION('',(1.E0,0.E0,0.E0)); -#36548=AXIS2_PLACEMENT_3D('',#36545,#36546,#36547); -#36549=PLANE('',#36548); -#36550=ORIENTED_EDGE('',*,*,#26660,.F.); -#36552=ORIENTED_EDGE('',*,*,#36551,.T.); -#36553=ORIENTED_EDGE('',*,*,#28749,.T.); -#36554=ORIENTED_EDGE('',*,*,#36538,.F.); -#36555=EDGE_LOOP('',(#36550,#36552,#36553,#36554)); -#36556=FACE_OUTER_BOUND('',#36555,.F.); -#36558=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.45E0)); -#36559=DIRECTION('',(5.513867982882E-1,0.E0,8.342497220098E-1)); -#36560=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#36561=AXIS2_PLACEMENT_3D('',#36558,#36559,#36560); -#36562=PLANE('',#36561); -#36563=ORIENTED_EDGE('',*,*,#26658,.F.); -#36565=ORIENTED_EDGE('',*,*,#36564,.T.); -#36566=ORIENTED_EDGE('',*,*,#28751,.T.); -#36567=ORIENTED_EDGE('',*,*,#36551,.F.); -#36568=EDGE_LOOP('',(#36563,#36565,#36566,#36567)); -#36569=FACE_OUTER_BOUND('',#36568,.F.); -#36571=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.524999713898E0)); -#36572=DIRECTION('',(8.697566915162E-1,0.E0,4.934807975624E-1)); -#36573=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#36574=AXIS2_PLACEMENT_3D('',#36571,#36572,#36573); -#36575=PLANE('',#36574); -#36576=ORIENTED_EDGE('',*,*,#26656,.F.); -#36578=ORIENTED_EDGE('',*,*,#36577,.T.); -#36579=ORIENTED_EDGE('',*,*,#28753,.T.); -#36580=ORIENTED_EDGE('',*,*,#36564,.F.); -#36581=EDGE_LOOP('',(#36576,#36578,#36579,#36580)); -#36582=FACE_OUTER_BOUND('',#36581,.F.); -#36584=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.600000286102E0)); -#36585=DIRECTION('',(9.620377540476E-1,0.E0,2.729163970653E-1)); -#36586=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#36587=AXIS2_PLACEMENT_3D('',#36584,#36585,#36586); -#36588=PLANE('',#36587); -#36589=ORIENTED_EDGE('',*,*,#26654,.F.); -#36591=ORIENTED_EDGE('',*,*,#36590,.T.); -#36592=ORIENTED_EDGE('',*,*,#28755,.T.); -#36593=ORIENTED_EDGE('',*,*,#36577,.F.); -#36594=EDGE_LOOP('',(#36589,#36591,#36592,#36593)); -#36595=FACE_OUTER_BOUND('',#36594,.F.); -#36597=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,1.675E0)); -#36598=DIRECTION('',(1.E0,0.E0,0.E0)); -#36599=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36600=AXIS2_PLACEMENT_3D('',#36597,#36598,#36599); -#36601=PLANE('',#36600); -#36602=ORIENTED_EDGE('',*,*,#26652,.F.); -#36604=ORIENTED_EDGE('',*,*,#36603,.T.); -#36605=ORIENTED_EDGE('',*,*,#28757,.T.); -#36606=ORIENTED_EDGE('',*,*,#36590,.F.); -#36607=EDGE_LOOP('',(#36602,#36604,#36605,#36606)); -#36608=FACE_OUTER_BOUND('',#36607,.F.); -#36610=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,1.749999713898E0)); -#36611=DIRECTION('',(9.620369340052E-1,0.E0,-2.729192877205E-1)); -#36612=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#36613=AXIS2_PLACEMENT_3D('',#36610,#36611,#36612); -#36614=PLANE('',#36613); -#36615=ORIENTED_EDGE('',*,*,#26650,.F.); -#36617=ORIENTED_EDGE('',*,*,#36616,.T.); -#36618=ORIENTED_EDGE('',*,*,#28759,.T.); -#36619=ORIENTED_EDGE('',*,*,#36603,.F.); -#36620=EDGE_LOOP('',(#36615,#36617,#36618,#36619)); -#36621=FACE_OUTER_BOUND('',#36620,.F.); -#36623=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,1.825000286102E0)); -#36624=DIRECTION('',(8.697591154214E-1,0.E0,-4.934765254207E-1)); -#36625=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#36626=AXIS2_PLACEMENT_3D('',#36623,#36624,#36625); -#36627=PLANE('',#36626); -#36628=ORIENTED_EDGE('',*,*,#26648,.F.); -#36630=ORIENTED_EDGE('',*,*,#36629,.T.); -#36631=ORIENTED_EDGE('',*,*,#28761,.T.); -#36632=ORIENTED_EDGE('',*,*,#36616,.F.); -#36633=EDGE_LOOP('',(#36628,#36630,#36631,#36632)); -#36634=FACE_OUTER_BOUND('',#36633,.F.); -#36636=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,1.881250286102E0)); -#36637=DIRECTION('',(5.513867982882E-1,0.E0,-8.342497220098E-1)); -#36638=DIRECTION('',(-8.342497220098E-1,0.E0,-5.513867982882E-1)); -#36639=AXIS2_PLACEMENT_3D('',#36636,#36637,#36638); -#36640=PLANE('',#36639); -#36641=ORIENTED_EDGE('',*,*,#26646,.F.); -#36643=ORIENTED_EDGE('',*,*,#36642,.T.); -#36644=ORIENTED_EDGE('',*,*,#28763,.T.); -#36645=ORIENTED_EDGE('',*,*,#36629,.F.); -#36646=EDGE_LOOP('',(#36641,#36643,#36644,#36645)); -#36647=FACE_OUTER_BOUND('',#36646,.F.); -#36649=CARTESIAN_POINT('',(3.744680851698E0,1.55E0,1.881250286102E0)); -#36650=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36651=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36652=AXIS2_PLACEMENT_3D('',#36649,#36650,#36651); -#36653=PLANE('',#36652); -#36654=ORIENTED_EDGE('',*,*,#26644,.F.); -#36656=ORIENTED_EDGE('',*,*,#36655,.T.); -#36657=ORIENTED_EDGE('',*,*,#28765,.T.); -#36658=ORIENTED_EDGE('',*,*,#36642,.F.); -#36659=EDGE_LOOP('',(#36654,#36656,#36657,#36658)); -#36660=FACE_OUTER_BOUND('',#36659,.F.); -#36662=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.825000286102E0)); -#36663=DIRECTION('',(-5.513868654785E-1,0.E0,-8.342496776013E-1)); -#36664=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654785E-1)); -#36665=AXIS2_PLACEMENT_3D('',#36662,#36663,#36664); -#36666=PLANE('',#36665); -#36667=ORIENTED_EDGE('',*,*,#26642,.F.); -#36669=ORIENTED_EDGE('',*,*,#36668,.T.); -#36670=ORIENTED_EDGE('',*,*,#28767,.T.); -#36671=ORIENTED_EDGE('',*,*,#36655,.F.); -#36672=EDGE_LOOP('',(#36667,#36669,#36670,#36671)); -#36673=FACE_OUTER_BOUND('',#36672,.F.); -#36675=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,1.749999713898E0)); -#36676=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#36677=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#36678=AXIS2_PLACEMENT_3D('',#36675,#36676,#36677); -#36679=PLANE('',#36678); -#36680=ORIENTED_EDGE('',*,*,#26640,.F.); -#36681=ORIENTED_EDGE('',*,*,#36488,.T.); -#36682=ORIENTED_EDGE('',*,*,#28769,.T.); -#36683=ORIENTED_EDGE('',*,*,#36668,.F.); -#36684=EDGE_LOOP('',(#36680,#36681,#36682,#36683)); -#36685=FACE_OUTER_BOUND('',#36684,.F.); -#36687=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.600000286102E0)); -#36688=DIRECTION('',(9.620377540476E-1,0.E0,2.729163970653E-1)); -#36689=DIRECTION('',(2.729163970653E-1,0.E0,-9.620377540476E-1)); -#36690=AXIS2_PLACEMENT_3D('',#36687,#36688,#36689); -#36691=PLANE('',#36690); -#36692=ORIENTED_EDGE('',*,*,#26678,.F.); -#36694=ORIENTED_EDGE('',*,*,#36693,.T.); -#36695=ORIENTED_EDGE('',*,*,#28773,.T.); -#36697=ORIENTED_EDGE('',*,*,#36696,.F.); -#36698=EDGE_LOOP('',(#36692,#36694,#36695,#36697)); -#36699=FACE_OUTER_BOUND('',#36698,.F.); -#36701=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,1.675E0)); -#36702=DIRECTION('',(1.E0,0.E0,0.E0)); -#36703=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36704=AXIS2_PLACEMENT_3D('',#36701,#36702,#36703); -#36705=PLANE('',#36704); -#36706=ORIENTED_EDGE('',*,*,#26708,.F.); -#36708=ORIENTED_EDGE('',*,*,#36707,.T.); -#36709=ORIENTED_EDGE('',*,*,#28775,.T.); -#36710=ORIENTED_EDGE('',*,*,#36693,.F.); -#36711=EDGE_LOOP('',(#36706,#36708,#36709,#36710)); -#36712=FACE_OUTER_BOUND('',#36711,.F.); -#36714=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.749999713898E0)); -#36715=DIRECTION('',(9.620369340052E-1,0.E0,-2.729192877205E-1)); -#36716=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#36717=AXIS2_PLACEMENT_3D('',#36714,#36715,#36716); -#36718=PLANE('',#36717); -#36719=ORIENTED_EDGE('',*,*,#26706,.F.); -#36721=ORIENTED_EDGE('',*,*,#36720,.T.); -#36722=ORIENTED_EDGE('',*,*,#28777,.T.); -#36723=ORIENTED_EDGE('',*,*,#36707,.F.); -#36724=EDGE_LOOP('',(#36719,#36721,#36722,#36723)); -#36725=FACE_OUTER_BOUND('',#36724,.F.); -#36727=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.825000286102E0)); -#36728=DIRECTION('',(7.615418683844E-1,0.E0,-6.481157170580E-1)); -#36729=DIRECTION('',(-6.481157170580E-1,0.E0,-7.615418683844E-1)); -#36730=AXIS2_PLACEMENT_3D('',#36727,#36728,#36729); -#36731=PLANE('',#36730); -#36732=ORIENTED_EDGE('',*,*,#26704,.F.); -#36734=ORIENTED_EDGE('',*,*,#36733,.T.); -#36735=ORIENTED_EDGE('',*,*,#28779,.T.); -#36736=ORIENTED_EDGE('',*,*,#36720,.F.); -#36737=EDGE_LOOP('',(#36732,#36734,#36735,#36736)); -#36738=FACE_OUTER_BOUND('',#36737,.F.); -#36740=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.862499713898E0)); -#36741=DIRECTION('',(5.065429958009E-1,0.E0,-8.622147026148E-1)); -#36742=DIRECTION('',(-8.622147026148E-1,0.E0,-5.065429958009E-1)); -#36743=AXIS2_PLACEMENT_3D('',#36740,#36741,#36742); -#36744=PLANE('',#36743); -#36745=ORIENTED_EDGE('',*,*,#26702,.F.); -#36747=ORIENTED_EDGE('',*,*,#36746,.T.); -#36748=ORIENTED_EDGE('',*,*,#28781,.T.); -#36749=ORIENTED_EDGE('',*,*,#36733,.F.); -#36750=EDGE_LOOP('',(#36745,#36747,#36748,#36749)); -#36751=FACE_OUTER_BOUND('',#36750,.F.); -#36753=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.862499713898E0)); -#36754=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36755=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36756=AXIS2_PLACEMENT_3D('',#36753,#36754,#36755); -#36757=PLANE('',#36756); -#36758=ORIENTED_EDGE('',*,*,#26700,.F.); -#36760=ORIENTED_EDGE('',*,*,#36759,.T.); -#36761=ORIENTED_EDGE('',*,*,#28783,.T.); -#36762=ORIENTED_EDGE('',*,*,#36746,.F.); -#36763=EDGE_LOOP('',(#36758,#36760,#36761,#36762)); -#36764=FACE_OUTER_BOUND('',#36763,.F.); -#36766=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.825000286102E0)); -#36767=DIRECTION('',(-5.065433474453E-1,0.E0,-8.622144960269E-1)); -#36768=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#36769=AXIS2_PLACEMENT_3D('',#36766,#36767,#36768); -#36770=PLANE('',#36769); -#36771=ORIENTED_EDGE('',*,*,#26698,.F.); -#36773=ORIENTED_EDGE('',*,*,#36772,.T.); -#36774=ORIENTED_EDGE('',*,*,#28785,.T.); -#36775=ORIENTED_EDGE('',*,*,#36759,.F.); -#36776=EDGE_LOOP('',(#36771,#36773,#36774,#36775)); -#36777=FACE_OUTER_BOUND('',#36776,.F.); -#36779=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.749999713898E0)); -#36780=DIRECTION('',(-7.615418683844E-1,0.E0,-6.481157170580E-1)); -#36781=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#36782=AXIS2_PLACEMENT_3D('',#36779,#36780,#36781); -#36783=PLANE('',#36782); -#36784=ORIENTED_EDGE('',*,*,#26696,.F.); -#36786=ORIENTED_EDGE('',*,*,#36785,.T.); -#36787=ORIENTED_EDGE('',*,*,#28787,.T.); -#36788=ORIENTED_EDGE('',*,*,#36772,.F.); -#36789=EDGE_LOOP('',(#36784,#36786,#36787,#36788)); -#36790=FACE_OUTER_BOUND('',#36789,.F.); -#36792=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.675E0)); -#36793=DIRECTION('',(-9.620369340052E-1,0.E0,-2.729192877205E-1)); -#36794=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#36795=AXIS2_PLACEMENT_3D('',#36792,#36793,#36794); -#36796=PLANE('',#36795); -#36797=ORIENTED_EDGE('',*,*,#26694,.F.); -#36799=ORIENTED_EDGE('',*,*,#36798,.T.); -#36800=ORIENTED_EDGE('',*,*,#28789,.T.); -#36801=ORIENTED_EDGE('',*,*,#36785,.F.); -#36802=EDGE_LOOP('',(#36797,#36799,#36800,#36801)); -#36803=FACE_OUTER_BOUND('',#36802,.F.); -#36805=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,1.600000286102E0)); -#36806=DIRECTION('',(-1.E0,0.E0,0.E0)); -#36807=DIRECTION('',(0.E0,0.E0,1.E0)); -#36808=AXIS2_PLACEMENT_3D('',#36805,#36806,#36807); -#36809=PLANE('',#36808); -#36810=ORIENTED_EDGE('',*,*,#26692,.F.); -#36812=ORIENTED_EDGE('',*,*,#36811,.T.); -#36813=ORIENTED_EDGE('',*,*,#28791,.T.); -#36814=ORIENTED_EDGE('',*,*,#36798,.F.); -#36815=EDGE_LOOP('',(#36810,#36812,#36813,#36814)); -#36816=FACE_OUTER_BOUND('',#36815,.F.); -#36818=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,1.524999713898E0)); -#36819=DIRECTION('',(-9.620377540476E-1,0.E0,2.729163970653E-1)); -#36820=DIRECTION('',(2.729163970653E-1,0.E0,9.620377540476E-1)); -#36821=AXIS2_PLACEMENT_3D('',#36818,#36819,#36820); -#36822=PLANE('',#36821); -#36823=ORIENTED_EDGE('',*,*,#26690,.F.); -#36825=ORIENTED_EDGE('',*,*,#36824,.T.); -#36826=ORIENTED_EDGE('',*,*,#28793,.T.); -#36827=ORIENTED_EDGE('',*,*,#36811,.F.); -#36828=EDGE_LOOP('',(#36823,#36825,#36826,#36827)); -#36829=FACE_OUTER_BOUND('',#36828,.F.); -#36831=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,1.45E0)); -#36832=DIRECTION('',(-7.615382075403E-1,0.E0,6.481200185586E-1)); -#36833=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#36834=AXIS2_PLACEMENT_3D('',#36831,#36832,#36833); -#36835=PLANE('',#36834); -#36836=ORIENTED_EDGE('',*,*,#26688,.F.); -#36838=ORIENTED_EDGE('',*,*,#36837,.T.); -#36839=ORIENTED_EDGE('',*,*,#28795,.T.); -#36840=ORIENTED_EDGE('',*,*,#36824,.F.); -#36841=EDGE_LOOP('',(#36836,#36838,#36839,#36840)); -#36842=FACE_OUTER_BOUND('',#36841,.F.); -#36844=CARTESIAN_POINT('',(3.297872364521E0,1.55E0,1.412499713898E0)); -#36845=DIRECTION('',(-5.065519665348E-1,0.E0,8.622094323305E-1)); -#36846=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#36847=AXIS2_PLACEMENT_3D('',#36844,#36845,#36846); -#36848=PLANE('',#36847); -#36849=ORIENTED_EDGE('',*,*,#26686,.F.); -#36851=ORIENTED_EDGE('',*,*,#36850,.T.); -#36852=ORIENTED_EDGE('',*,*,#28797,.T.); -#36853=ORIENTED_EDGE('',*,*,#36837,.F.); -#36854=EDGE_LOOP('',(#36849,#36851,#36852,#36853)); -#36855=FACE_OUTER_BOUND('',#36854,.F.); -#36857=CARTESIAN_POINT('',(3.255319178104E0,1.55E0,1.412499713898E0)); -#36858=DIRECTION('',(0.E0,0.E0,1.E0)); -#36859=DIRECTION('',(1.E0,0.E0,0.E0)); -#36860=AXIS2_PLACEMENT_3D('',#36857,#36858,#36859); -#36861=PLANE('',#36860); -#36862=ORIENTED_EDGE('',*,*,#26684,.F.); -#36864=ORIENTED_EDGE('',*,*,#36863,.T.); -#36865=ORIENTED_EDGE('',*,*,#28799,.T.); -#36866=ORIENTED_EDGE('',*,*,#36850,.F.); -#36867=EDGE_LOOP('',(#36862,#36864,#36865,#36866)); -#36868=FACE_OUTER_BOUND('',#36867,.F.); -#36870=CARTESIAN_POINT('',(3.191489338875E0,1.55E0,1.45E0)); -#36871=DIRECTION('',(5.065516148885E-1,0.E0,8.622096389243E-1)); -#36872=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#36873=AXIS2_PLACEMENT_3D('',#36870,#36871,#36872); -#36874=PLANE('',#36873); -#36875=ORIENTED_EDGE('',*,*,#26682,.F.); -#36877=ORIENTED_EDGE('',*,*,#36876,.T.); -#36878=ORIENTED_EDGE('',*,*,#28801,.T.); -#36879=ORIENTED_EDGE('',*,*,#36863,.F.); -#36880=EDGE_LOOP('',(#36875,#36877,#36878,#36879)); -#36881=FACE_OUTER_BOUND('',#36880,.F.); -#36883=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.524999713898E0)); -#36884=DIRECTION('',(7.615382075403E-1,0.E0,6.481200185586E-1)); -#36885=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#36886=AXIS2_PLACEMENT_3D('',#36883,#36884,#36885); -#36887=PLANE('',#36886); -#36888=ORIENTED_EDGE('',*,*,#26680,.F.); -#36889=ORIENTED_EDGE('',*,*,#36696,.T.); -#36890=ORIENTED_EDGE('',*,*,#28803,.T.); -#36891=ORIENTED_EDGE('',*,*,#36876,.F.); -#36892=EDGE_LOOP('',(#36888,#36889,#36890,#36891)); -#36893=FACE_OUTER_BOUND('',#36892,.F.); -#36895=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,5.312502861023E-1)); -#36896=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#36897=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#36898=AXIS2_PLACEMENT_3D('',#36895,#36896,#36897); -#36899=PLANE('',#36898); -#36900=ORIENTED_EDGE('',*,*,#25406,.F.); -#36902=ORIENTED_EDGE('',*,*,#36901,.T.); -#36903=ORIENTED_EDGE('',*,*,#28820,.T.); -#36905=ORIENTED_EDGE('',*,*,#36904,.F.); -#36906=EDGE_LOOP('',(#36900,#36902,#36903,#36905)); -#36907=FACE_OUTER_BOUND('',#36906,.F.); -#36909=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,5.875002861023E-1)); -#36910=DIRECTION('',(7.975044357522E-1,0.E0,-6.033130820359E-1)); -#36911=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#36912=AXIS2_PLACEMENT_3D('',#36909,#36910,#36911); -#36913=PLANE('',#36912); -#36914=ORIENTED_EDGE('',*,*,#25518,.F.); -#36916=ORIENTED_EDGE('',*,*,#36915,.T.); -#36917=ORIENTED_EDGE('',*,*,#28822,.T.); -#36918=ORIENTED_EDGE('',*,*,#36901,.F.); -#36919=EDGE_LOOP('',(#36914,#36916,#36917,#36918)); -#36920=FACE_OUTER_BOUND('',#36919,.F.); -#36922=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,6.625E-1)); -#36923=DIRECTION('',(8.697566637025E-1,0.E0,-4.934808465838E-1)); -#36924=DIRECTION('',(-4.934808465838E-1,0.E0,-8.697566637025E-1)); -#36925=AXIS2_PLACEMENT_3D('',#36922,#36923,#36924); -#36926=PLANE('',#36925); -#36927=ORIENTED_EDGE('',*,*,#25516,.F.); -#36929=ORIENTED_EDGE('',*,*,#36928,.T.); -#36930=ORIENTED_EDGE('',*,*,#28824,.T.); -#36931=ORIENTED_EDGE('',*,*,#36915,.F.); -#36932=EDGE_LOOP('',(#36927,#36929,#36930,#36931)); -#36933=FACE_OUTER_BOUND('',#36932,.F.); -#36935=CARTESIAN_POINT('',(4.E0,1.55E0,7.374997138977E-1)); -#36936=DIRECTION('',(9.620369277320E-1,0.E0,-2.729193098334E-1)); -#36937=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#36938=AXIS2_PLACEMENT_3D('',#36935,#36936,#36937); -#36939=PLANE('',#36938); -#36940=ORIENTED_EDGE('',*,*,#25514,.F.); -#36942=ORIENTED_EDGE('',*,*,#36941,.T.); -#36943=ORIENTED_EDGE('',*,*,#28826,.T.); -#36944=ORIENTED_EDGE('',*,*,#36928,.F.); -#36945=EDGE_LOOP('',(#36940,#36942,#36943,#36944)); -#36946=FACE_OUTER_BOUND('',#36945,.F.); -#36948=CARTESIAN_POINT('',(4.E0,1.55E0,8.875E-1)); -#36949=DIRECTION('',(1.E0,0.E0,0.E0)); -#36950=DIRECTION('',(0.E0,0.E0,-1.E0)); -#36951=AXIS2_PLACEMENT_3D('',#36948,#36949,#36950); -#36952=PLANE('',#36951); -#36953=ORIENTED_EDGE('',*,*,#25512,.F.); -#36955=ORIENTED_EDGE('',*,*,#36954,.T.); -#36956=ORIENTED_EDGE('',*,*,#28828,.T.); -#36957=ORIENTED_EDGE('',*,*,#36941,.F.); -#36958=EDGE_LOOP('',(#36953,#36955,#36956,#36957)); -#36959=FACE_OUTER_BOUND('',#36958,.F.); -#36961=CARTESIAN_POINT('',(3.978723404929E0,1.55E0,9.624997138977E-1)); -#36962=DIRECTION('',(9.620369277320E-1,0.E0,2.729193098334E-1)); -#36963=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#36964=AXIS2_PLACEMENT_3D('',#36961,#36962,#36963); -#36965=PLANE('',#36964); -#36966=ORIENTED_EDGE('',*,*,#25510,.F.); -#36968=ORIENTED_EDGE('',*,*,#36967,.T.); -#36969=ORIENTED_EDGE('',*,*,#28830,.T.); -#36970=ORIENTED_EDGE('',*,*,#36954,.F.); -#36971=EDGE_LOOP('',(#36966,#36968,#36969,#36970)); -#36972=FACE_OUTER_BOUND('',#36971,.F.); -#36974=CARTESIAN_POINT('',(3.936170212924E0,1.55E0,1.037500286102E0)); -#36975=DIRECTION('',(8.697590876082E-1,0.E0,4.934765744419E-1)); -#36976=DIRECTION('',(4.934765744419E-1,0.E0,-8.697590876082E-1)); -#36977=AXIS2_PLACEMENT_3D('',#36974,#36975,#36976); -#36978=PLANE('',#36977); -#36979=ORIENTED_EDGE('',*,*,#25508,.F.); -#36981=ORIENTED_EDGE('',*,*,#36980,.T.); -#36982=ORIENTED_EDGE('',*,*,#28832,.T.); -#36983=ORIENTED_EDGE('',*,*,#36967,.F.); -#36984=EDGE_LOOP('',(#36979,#36981,#36982,#36983)); -#36985=FACE_OUTER_BOUND('',#36984,.F.); -#36987=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.093750286102E0)); -#36988=DIRECTION('',(7.975044357522E-1,0.E0,6.033130820359E-1)); -#36989=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#36990=AXIS2_PLACEMENT_3D('',#36987,#36988,#36989); -#36991=PLANE('',#36990); -#36992=ORIENTED_EDGE('',*,*,#25506,.F.); -#36994=ORIENTED_EDGE('',*,*,#36993,.T.); -#36995=ORIENTED_EDGE('',*,*,#28834,.T.); -#36996=ORIENTED_EDGE('',*,*,#36980,.F.); -#36997=EDGE_LOOP('',(#36992,#36994,#36995,#36996)); -#36998=FACE_OUTER_BOUND('',#36997,.F.); -#37000=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,1.131249713898E0)); -#37001=DIRECTION('',(5.065433474453E-1,0.E0,8.622144960269E-1)); -#37002=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#37003=AXIS2_PLACEMENT_3D('',#37000,#37001,#37002); -#37004=PLANE('',#37003); -#37005=ORIENTED_EDGE('',*,*,#25504,.F.); -#37007=ORIENTED_EDGE('',*,*,#37006,.T.); -#37008=ORIENTED_EDGE('',*,*,#28836,.T.); -#37009=ORIENTED_EDGE('',*,*,#36993,.F.); -#37010=EDGE_LOOP('',(#37005,#37007,#37008,#37009)); -#37011=FACE_OUTER_BOUND('',#37010,.F.); -#37013=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.150000286102E0)); -#37014=DIRECTION('',(2.818495377036E-1,0.E0,9.594586171880E-1)); -#37015=DIRECTION('',(9.594586171880E-1,0.E0,-2.818495377036E-1)); -#37016=AXIS2_PLACEMENT_3D('',#37013,#37014,#37015); -#37017=PLANE('',#37016); -#37018=ORIENTED_EDGE('',*,*,#25502,.F.); -#37020=ORIENTED_EDGE('',*,*,#37019,.T.); -#37021=ORIENTED_EDGE('',*,*,#28838,.T.); -#37022=ORIENTED_EDGE('',*,*,#37006,.F.); -#37023=EDGE_LOOP('',(#37018,#37020,#37021,#37022)); -#37024=FACE_OUTER_BOUND('',#37023,.F.); -#37026=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,1.05625E0)); -#37027=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37028=DIRECTION('',(0.E0,0.E0,1.E0)); -#37029=AXIS2_PLACEMENT_3D('',#37026,#37027,#37028); -#37030=PLANE('',#37029); -#37031=ORIENTED_EDGE('',*,*,#25500,.F.); -#37033=ORIENTED_EDGE('',*,*,#37032,.T.); -#37034=ORIENTED_EDGE('',*,*,#28840,.T.); -#37035=ORIENTED_EDGE('',*,*,#37019,.F.); -#37036=EDGE_LOOP('',(#37031,#37033,#37034,#37035)); -#37037=FACE_OUTER_BOUND('',#37036,.F.); -#37039=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,1.037500286102E0)); -#37040=DIRECTION('',(-4.032126193069E-1,0.E0,-9.151063236759E-1)); -#37041=DIRECTION('',(-9.151063236759E-1,0.E0,4.032126193069E-1)); -#37042=AXIS2_PLACEMENT_3D('',#37039,#37040,#37041); -#37043=PLANE('',#37042); -#37044=ORIENTED_EDGE('',*,*,#25498,.F.); -#37046=ORIENTED_EDGE('',*,*,#37045,.T.); -#37047=ORIENTED_EDGE('',*,*,#28842,.T.); -#37048=ORIENTED_EDGE('',*,*,#37032,.F.); -#37049=EDGE_LOOP('',(#37044,#37046,#37047,#37048)); -#37050=FACE_OUTER_BOUND('',#37049,.F.); -#37052=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,1.E0)); -#37053=DIRECTION('',(-6.611590069362E-1,0.E0,-7.502458047514E-1)); -#37054=DIRECTION('',(-7.502458047514E-1,0.E0,6.611590069362E-1)); -#37055=AXIS2_PLACEMENT_3D('',#37052,#37053,#37054); -#37056=PLANE('',#37055); -#37057=ORIENTED_EDGE('',*,*,#25496,.F.); -#37059=ORIENTED_EDGE('',*,*,#37058,.T.); -#37060=ORIENTED_EDGE('',*,*,#28844,.T.); -#37061=ORIENTED_EDGE('',*,*,#37045,.F.); -#37062=EDGE_LOOP('',(#37057,#37059,#37060,#37061)); -#37063=FACE_OUTER_BOUND('',#37062,.F.); -#37065=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,9.624997138977E-1)); -#37066=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254208E-1)); -#37067=DIRECTION('',(-4.934765254208E-1,0.E0,8.697591154214E-1)); -#37068=AXIS2_PLACEMENT_3D('',#37065,#37066,#37067); -#37069=PLANE('',#37068); -#37070=ORIENTED_EDGE('',*,*,#25494,.F.); -#37072=ORIENTED_EDGE('',*,*,#37071,.T.); -#37073=ORIENTED_EDGE('',*,*,#28846,.T.); -#37074=ORIENTED_EDGE('',*,*,#37058,.F.); -#37075=EDGE_LOOP('',(#37070,#37072,#37073,#37074)); -#37076=FACE_OUTER_BOUND('',#37075,.F.); -#37078=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,8.687502861023E-1)); -#37079=DIRECTION('',(-9.752004643543E-1,0.E0,-2.213234156683E-1)); -#37080=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#37081=AXIS2_PLACEMENT_3D('',#37078,#37079,#37080); -#37082=PLANE('',#37081); -#37083=ORIENTED_EDGE('',*,*,#25492,.F.); -#37085=ORIENTED_EDGE('',*,*,#37084,.T.); -#37086=ORIENTED_EDGE('',*,*,#28848,.T.); -#37087=ORIENTED_EDGE('',*,*,#37071,.F.); -#37088=EDGE_LOOP('',(#37083,#37085,#37086,#37087)); -#37089=FACE_OUTER_BOUND('',#37088,.F.); -#37091=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,7.562502861023E-1)); -#37092=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37093=DIRECTION('',(0.E0,0.E0,1.E0)); -#37094=AXIS2_PLACEMENT_3D('',#37091,#37092,#37093); -#37095=PLANE('',#37094); -#37096=ORIENTED_EDGE('',*,*,#25490,.F.); -#37098=ORIENTED_EDGE('',*,*,#37097,.T.); -#37099=ORIENTED_EDGE('',*,*,#28850,.T.); -#37100=ORIENTED_EDGE('',*,*,#37084,.F.); -#37101=EDGE_LOOP('',(#37096,#37098,#37099,#37100)); -#37102=FACE_OUTER_BOUND('',#37101,.F.); -#37104=CARTESIAN_POINT('',(3.872340425849E0,1.55E0,6.625E-1)); -#37105=DIRECTION('',(-9.752009016921E-1,0.E0,2.213214886517E-1)); -#37106=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#37107=AXIS2_PLACEMENT_3D('',#37104,#37105,#37106); -#37108=PLANE('',#37107); -#37109=ORIENTED_EDGE('',*,*,#25488,.F.); -#37111=ORIENTED_EDGE('',*,*,#37110,.T.); -#37112=ORIENTED_EDGE('',*,*,#28852,.T.); -#37113=ORIENTED_EDGE('',*,*,#37097,.F.); -#37114=EDGE_LOOP('',(#37109,#37111,#37112,#37113)); -#37115=FACE_OUTER_BOUND('',#37114,.F.); -#37117=CARTESIAN_POINT('',(3.851063832641E0,1.55E0,6.249997138977E-1)); -#37118=DIRECTION('',(-8.697591154214E-1,0.E0,4.934765254207E-1)); -#37119=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#37120=AXIS2_PLACEMENT_3D('',#37117,#37118,#37119); -#37121=PLANE('',#37120); -#37122=ORIENTED_EDGE('',*,*,#25486,.F.); -#37124=ORIENTED_EDGE('',*,*,#37123,.T.); -#37125=ORIENTED_EDGE('',*,*,#28854,.T.); -#37126=ORIENTED_EDGE('',*,*,#37110,.F.); -#37127=EDGE_LOOP('',(#37122,#37124,#37125,#37126)); -#37128=FACE_OUTER_BOUND('',#37127,.F.); -#37130=CARTESIAN_POINT('',(3.808510631323E0,1.55E0,5.875002861023E-1)); -#37131=DIRECTION('',(-6.611504891330E-1,0.E0,7.502533110351E-1)); -#37132=DIRECTION('',(7.502533110351E-1,0.E0,6.611504891330E-1)); -#37133=AXIS2_PLACEMENT_3D('',#37130,#37131,#37132); -#37134=PLANE('',#37133); -#37135=ORIENTED_EDGE('',*,*,#25484,.F.); -#37137=ORIENTED_EDGE('',*,*,#37136,.T.); -#37138=ORIENTED_EDGE('',*,*,#28856,.T.); -#37139=ORIENTED_EDGE('',*,*,#37123,.F.); -#37140=EDGE_LOOP('',(#37135,#37137,#37138,#37139)); -#37141=FACE_OUTER_BOUND('',#37140,.F.); -#37143=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,5.687497138977E-1)); -#37144=DIRECTION('',(-4.032280761334E-1,0.E0,9.150995129590E-1)); -#37145=DIRECTION('',(9.150995129590E-1,0.E0,4.032280761334E-1)); -#37146=AXIS2_PLACEMENT_3D('',#37143,#37144,#37145); -#37147=PLANE('',#37146); -#37148=ORIENTED_EDGE('',*,*,#25482,.F.); -#37150=ORIENTED_EDGE('',*,*,#37149,.T.); -#37151=ORIENTED_EDGE('',*,*,#28858,.T.); -#37152=ORIENTED_EDGE('',*,*,#37136,.F.); -#37153=EDGE_LOOP('',(#37148,#37150,#37151,#37152)); -#37154=FACE_OUTER_BOUND('',#37153,.F.); -#37156=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,5.687497138977E-1)); -#37157=DIRECTION('',(0.E0,0.E0,1.E0)); -#37158=DIRECTION('',(1.E0,0.E0,0.E0)); -#37159=AXIS2_PLACEMENT_3D('',#37156,#37157,#37158); -#37160=PLANE('',#37159); -#37161=ORIENTED_EDGE('',*,*,#25480,.F.); -#37163=ORIENTED_EDGE('',*,*,#37162,.T.); -#37164=ORIENTED_EDGE('',*,*,#28860,.T.); -#37165=ORIENTED_EDGE('',*,*,#37149,.F.); -#37166=EDGE_LOOP('',(#37161,#37163,#37164,#37165)); -#37167=FACE_OUTER_BOUND('',#37166,.F.); -#37169=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,6.0625E-1)); -#37170=DIRECTION('',(4.032202295217E-1,0.E0,9.151029704380E-1)); -#37171=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#37172=AXIS2_PLACEMENT_3D('',#37169,#37170,#37171); -#37173=PLANE('',#37172); -#37174=ORIENTED_EDGE('',*,*,#25478,.F.); -#37176=ORIENTED_EDGE('',*,*,#37175,.T.); -#37177=ORIENTED_EDGE('',*,*,#28862,.T.); -#37178=ORIENTED_EDGE('',*,*,#37162,.F.); -#37179=EDGE_LOOP('',(#37174,#37176,#37177,#37178)); -#37180=FACE_OUTER_BOUND('',#37179,.F.); -#37182=CARTESIAN_POINT('',(3.553191483021E0,1.55E0,6.625E-1)); -#37183=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#37184=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#37185=AXIS2_PLACEMENT_3D('',#37182,#37183,#37184); -#37186=PLANE('',#37185); -#37187=ORIENTED_EDGE('',*,*,#25476,.F.); -#37189=ORIENTED_EDGE('',*,*,#37188,.T.); -#37190=ORIENTED_EDGE('',*,*,#28864,.T.); -#37191=ORIENTED_EDGE('',*,*,#37175,.F.); -#37192=EDGE_LOOP('',(#37187,#37189,#37190,#37191)); -#37193=FACE_OUTER_BOUND('',#37192,.F.); -#37195=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,7.75E-1)); -#37196=DIRECTION('',(9.825817148807E-1,0.E0,1.858310350350E-1)); -#37197=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#37198=AXIS2_PLACEMENT_3D('',#37195,#37196,#37197); -#37199=PLANE('',#37198); -#37200=ORIENTED_EDGE('',*,*,#25474,.F.); -#37202=ORIENTED_EDGE('',*,*,#37201,.T.); -#37203=ORIENTED_EDGE('',*,*,#28866,.T.); -#37204=ORIENTED_EDGE('',*,*,#37188,.F.); -#37205=EDGE_LOOP('',(#37200,#37202,#37203,#37204)); -#37206=FACE_OUTER_BOUND('',#37205,.F.); -#37208=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,8.499997138977E-1)); -#37209=DIRECTION('',(1.E0,0.E0,0.E0)); -#37210=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37211=AXIS2_PLACEMENT_3D('',#37208,#37209,#37210); -#37212=PLANE('',#37211); -#37213=ORIENTED_EDGE('',*,*,#25472,.F.); -#37215=ORIENTED_EDGE('',*,*,#37214,.T.); -#37216=ORIENTED_EDGE('',*,*,#28868,.T.); -#37217=ORIENTED_EDGE('',*,*,#37201,.F.); -#37218=EDGE_LOOP('',(#37213,#37215,#37216,#37217)); -#37219=FACE_OUTER_BOUND('',#37218,.F.); -#37221=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,8.499997138977E-1)); -#37222=DIRECTION('',(0.E0,0.E0,1.E0)); -#37223=DIRECTION('',(1.E0,0.E0,0.E0)); -#37224=AXIS2_PLACEMENT_3D('',#37221,#37222,#37223); -#37225=PLANE('',#37224); -#37226=ORIENTED_EDGE('',*,*,#25470,.F.); -#37228=ORIENTED_EDGE('',*,*,#37227,.T.); -#37229=ORIENTED_EDGE('',*,*,#28870,.T.); -#37230=ORIENTED_EDGE('',*,*,#37214,.F.); -#37231=EDGE_LOOP('',(#37226,#37228,#37229,#37230)); -#37232=FACE_OUTER_BOUND('',#37231,.F.); -#37234=CARTESIAN_POINT('',(3.446808516979E0,1.55E0,7.75E-1)); -#37235=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37236=DIRECTION('',(0.E0,0.E0,1.E0)); -#37237=AXIS2_PLACEMENT_3D('',#37234,#37235,#37236); -#37238=PLANE('',#37237); -#37239=ORIENTED_EDGE('',*,*,#25468,.F.); -#37241=ORIENTED_EDGE('',*,*,#37240,.T.); -#37242=ORIENTED_EDGE('',*,*,#28872,.T.); -#37243=ORIENTED_EDGE('',*,*,#37227,.F.); -#37244=EDGE_LOOP('',(#37239,#37241,#37242,#37243)); -#37245=FACE_OUTER_BOUND('',#37244,.F.); -#37247=CARTESIAN_POINT('',(3.404255330563E0,1.55E0,6.625E-1)); -#37248=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#37249=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#37250=AXIS2_PLACEMENT_3D('',#37247,#37248,#37249); -#37251=PLANE('',#37250); -#37252=ORIENTED_EDGE('',*,*,#25466,.F.); -#37254=ORIENTED_EDGE('',*,*,#37253,.T.); -#37255=ORIENTED_EDGE('',*,*,#28874,.T.); -#37256=ORIENTED_EDGE('',*,*,#37240,.F.); -#37257=EDGE_LOOP('',(#37252,#37254,#37255,#37256)); -#37258=FACE_OUTER_BOUND('',#37257,.F.); -#37260=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,6.249997138977E-1)); -#37261=DIRECTION('',(-6.611591372532E-1,0.E0,7.502456899087E-1)); -#37262=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#37263=AXIS2_PLACEMENT_3D('',#37260,#37261,#37262); -#37264=PLANE('',#37263); -#37265=ORIENTED_EDGE('',*,*,#25464,.F.); -#37267=ORIENTED_EDGE('',*,*,#37266,.T.); -#37268=ORIENTED_EDGE('',*,*,#28876,.T.); -#37269=ORIENTED_EDGE('',*,*,#37253,.F.); -#37270=EDGE_LOOP('',(#37265,#37267,#37268,#37269)); -#37271=FACE_OUTER_BOUND('',#37270,.F.); -#37273=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,5.875002861023E-1)); -#37274=DIRECTION('',(-4.032126193069E-1,0.E0,9.151063236759E-1)); -#37275=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#37276=AXIS2_PLACEMENT_3D('',#37273,#37274,#37275); -#37277=PLANE('',#37276); -#37278=ORIENTED_EDGE('',*,*,#25462,.F.); -#37280=ORIENTED_EDGE('',*,*,#37279,.T.); -#37281=ORIENTED_EDGE('',*,*,#28878,.T.); -#37282=ORIENTED_EDGE('',*,*,#37266,.F.); -#37283=EDGE_LOOP('',(#37278,#37280,#37281,#37282)); -#37284=FACE_OUTER_BOUND('',#37283,.F.); -#37286=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,5.875002861023E-1)); -#37287=DIRECTION('',(0.E0,0.E0,1.E0)); -#37288=DIRECTION('',(1.E0,0.E0,0.E0)); -#37289=AXIS2_PLACEMENT_3D('',#37286,#37287,#37288); -#37290=PLANE('',#37289); -#37291=ORIENTED_EDGE('',*,*,#25460,.F.); -#37293=ORIENTED_EDGE('',*,*,#37292,.T.); -#37294=ORIENTED_EDGE('',*,*,#28880,.T.); -#37295=ORIENTED_EDGE('',*,*,#37279,.F.); -#37296=EDGE_LOOP('',(#37291,#37293,#37294,#37295)); -#37297=FACE_OUTER_BOUND('',#37296,.F.); -#37299=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,6.249997138977E-1)); -#37300=DIRECTION('',(5.065433474453E-1,0.E0,8.622144960269E-1)); -#37301=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#37302=AXIS2_PLACEMENT_3D('',#37299,#37300,#37301); -#37303=PLANE('',#37302); -#37304=ORIENTED_EDGE('',*,*,#25458,.F.); -#37306=ORIENTED_EDGE('',*,*,#37305,.T.); -#37307=ORIENTED_EDGE('',*,*,#28882,.T.); -#37308=ORIENTED_EDGE('',*,*,#37292,.F.); -#37309=EDGE_LOOP('',(#37304,#37306,#37307,#37308)); -#37310=FACE_OUTER_BOUND('',#37309,.F.); -#37312=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,6.812497138977E-1)); -#37313=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#37314=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#37315=AXIS2_PLACEMENT_3D('',#37312,#37313,#37314); -#37316=PLANE('',#37315); -#37317=ORIENTED_EDGE('',*,*,#25456,.F.); -#37319=ORIENTED_EDGE('',*,*,#37318,.T.); -#37320=ORIENTED_EDGE('',*,*,#28884,.T.); -#37321=ORIENTED_EDGE('',*,*,#37305,.F.); -#37322=EDGE_LOOP('',(#37317,#37319,#37320,#37321)); -#37323=FACE_OUTER_BOUND('',#37322,.F.); -#37325=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,7.75E-1)); -#37326=DIRECTION('',(9.752009016921E-1,0.E0,2.213214886517E-1)); -#37327=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#37328=AXIS2_PLACEMENT_3D('',#37325,#37326,#37327); -#37329=PLANE('',#37328); -#37330=ORIENTED_EDGE('',*,*,#25454,.F.); -#37332=ORIENTED_EDGE('',*,*,#37331,.T.); -#37333=ORIENTED_EDGE('',*,*,#28886,.T.); -#37334=ORIENTED_EDGE('',*,*,#37318,.F.); -#37335=EDGE_LOOP('',(#37330,#37332,#37333,#37334)); -#37336=FACE_OUTER_BOUND('',#37335,.F.); -#37338=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,8.499997138977E-1)); -#37339=DIRECTION('',(1.E0,0.E0,0.E0)); -#37340=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37341=AXIS2_PLACEMENT_3D('',#37338,#37339,#37340); -#37342=PLANE('',#37341); -#37343=ORIENTED_EDGE('',*,*,#25452,.F.); -#37345=ORIENTED_EDGE('',*,*,#37344,.T.); -#37346=ORIENTED_EDGE('',*,*,#28888,.T.); -#37347=ORIENTED_EDGE('',*,*,#37331,.F.); -#37348=EDGE_LOOP('',(#37343,#37345,#37346,#37347)); -#37349=FACE_OUTER_BOUND('',#37348,.F.); -#37351=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,9.4375E-1)); -#37352=DIRECTION('',(9.752009016921E-1,0.E0,-2.213214886517E-1)); -#37353=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#37354=AXIS2_PLACEMENT_3D('',#37351,#37352,#37353); -#37355=PLANE('',#37354); -#37356=ORIENTED_EDGE('',*,*,#25450,.F.); -#37358=ORIENTED_EDGE('',*,*,#37357,.T.); -#37359=ORIENTED_EDGE('',*,*,#28890,.T.); -#37360=ORIENTED_EDGE('',*,*,#37344,.F.); -#37361=EDGE_LOOP('',(#37356,#37358,#37359,#37360)); -#37362=FACE_OUTER_BOUND('',#37361,.F.); -#37364=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.E0)); -#37365=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#37366=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#37367=AXIS2_PLACEMENT_3D('',#37364,#37365,#37366); -#37368=PLANE('',#37367); -#37369=ORIENTED_EDGE('',*,*,#25448,.F.); -#37371=ORIENTED_EDGE('',*,*,#37370,.T.); -#37372=ORIENTED_EDGE('',*,*,#28892,.T.); -#37373=ORIENTED_EDGE('',*,*,#37357,.F.); -#37374=EDGE_LOOP('',(#37369,#37371,#37372,#37373)); -#37375=FACE_OUTER_BOUND('',#37374,.F.); -#37377=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.037500286102E0)); -#37378=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#37379=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#37380=AXIS2_PLACEMENT_3D('',#37377,#37378,#37379); -#37381=PLANE('',#37380); -#37382=ORIENTED_EDGE('',*,*,#25446,.F.); -#37384=ORIENTED_EDGE('',*,*,#37383,.T.); -#37385=ORIENTED_EDGE('',*,*,#28894,.T.); -#37386=ORIENTED_EDGE('',*,*,#37370,.F.); -#37387=EDGE_LOOP('',(#37382,#37384,#37385,#37386)); -#37388=FACE_OUTER_BOUND('',#37387,.F.); -#37390=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,1.131249713898E0)); -#37391=DIRECTION('',(1.E0,0.E0,0.E0)); -#37392=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37393=AXIS2_PLACEMENT_3D('',#37390,#37391,#37392); -#37394=PLANE('',#37393); -#37395=ORIENTED_EDGE('',*,*,#25444,.F.); -#37397=ORIENTED_EDGE('',*,*,#37396,.T.); -#37398=ORIENTED_EDGE('',*,*,#28896,.T.); -#37399=ORIENTED_EDGE('',*,*,#37383,.F.); -#37400=EDGE_LOOP('',(#37395,#37397,#37398,#37399)); -#37401=FACE_OUTER_BOUND('',#37400,.F.); -#37403=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,1.1125E0)); -#37404=DIRECTION('',(-2.151497590808E-1,0.E0,9.765810673812E-1)); -#37405=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#37406=AXIS2_PLACEMENT_3D('',#37403,#37404,#37405); -#37407=PLANE('',#37406); -#37408=ORIENTED_EDGE('',*,*,#25442,.F.); -#37410=ORIENTED_EDGE('',*,*,#37409,.T.); -#37411=ORIENTED_EDGE('',*,*,#28898,.T.); -#37412=ORIENTED_EDGE('',*,*,#37396,.F.); -#37413=EDGE_LOOP('',(#37408,#37410,#37411,#37412)); -#37414=FACE_OUTER_BOUND('',#37413,.F.); -#37416=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,1.037500286102E0)); -#37417=DIRECTION('',(-6.611548783840E-1,0.E0,7.502494430448E-1)); -#37418=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#37419=AXIS2_PLACEMENT_3D('',#37416,#37417,#37418); -#37420=PLANE('',#37419); -#37421=ORIENTED_EDGE('',*,*,#25440,.F.); -#37423=ORIENTED_EDGE('',*,*,#37422,.T.); -#37424=ORIENTED_EDGE('',*,*,#28900,.T.); -#37425=ORIENTED_EDGE('',*,*,#37409,.F.); -#37426=EDGE_LOOP('',(#37421,#37423,#37424,#37425)); -#37427=FACE_OUTER_BOUND('',#37426,.F.); -#37429=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,9.624997138977E-1)); -#37430=DIRECTION('',(-8.697591154214E-1,0.E0,4.934765254207E-1)); -#37431=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#37432=AXIS2_PLACEMENT_3D('',#37429,#37430,#37431); -#37433=PLANE('',#37432); -#37434=ORIENTED_EDGE('',*,*,#25438,.F.); -#37436=ORIENTED_EDGE('',*,*,#37435,.T.); -#37437=ORIENTED_EDGE('',*,*,#28902,.T.); -#37438=ORIENTED_EDGE('',*,*,#37422,.F.); -#37439=EDGE_LOOP('',(#37434,#37436,#37437,#37438)); -#37440=FACE_OUTER_BOUND('',#37439,.F.); -#37442=CARTESIAN_POINT('',(3.E0,1.55E0,8.3125E-1)); -#37443=DIRECTION('',(-9.871139661698E-1,0.E0,1.600188044967E-1)); -#37444=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#37445=AXIS2_PLACEMENT_3D('',#37442,#37443,#37444); -#37446=PLANE('',#37445); -#37447=ORIENTED_EDGE('',*,*,#25436,.F.); -#37449=ORIENTED_EDGE('',*,*,#37448,.T.); -#37450=ORIENTED_EDGE('',*,*,#28904,.T.); -#37451=ORIENTED_EDGE('',*,*,#37435,.F.); -#37452=EDGE_LOOP('',(#37447,#37449,#37450,#37451)); -#37453=FACE_OUTER_BOUND('',#37452,.F.); -#37455=CARTESIAN_POINT('',(3.E0,1.55E0,7.937497138977E-1)); -#37456=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37457=DIRECTION('',(0.E0,0.E0,1.E0)); -#37458=AXIS2_PLACEMENT_3D('',#37455,#37456,#37457); -#37459=PLANE('',#37458); -#37460=ORIENTED_EDGE('',*,*,#25434,.F.); -#37462=ORIENTED_EDGE('',*,*,#37461,.T.); -#37463=ORIENTED_EDGE('',*,*,#28906,.T.); -#37464=ORIENTED_EDGE('',*,*,#37448,.F.); -#37465=EDGE_LOOP('',(#37460,#37462,#37463,#37464)); -#37466=FACE_OUTER_BOUND('',#37465,.F.); -#37468=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,6.625E-1)); -#37469=DIRECTION('',(-9.871139661698E-1,0.E0,-1.600188044967E-1)); -#37470=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#37471=AXIS2_PLACEMENT_3D('',#37468,#37469,#37470); -#37472=PLANE('',#37471); -#37473=ORIENTED_EDGE('',*,*,#25432,.F.); -#37475=ORIENTED_EDGE('',*,*,#37474,.T.); -#37476=ORIENTED_EDGE('',*,*,#28908,.T.); -#37477=ORIENTED_EDGE('',*,*,#37461,.F.); -#37478=EDGE_LOOP('',(#37473,#37475,#37476,#37477)); -#37479=FACE_OUTER_BOUND('',#37478,.F.); -#37481=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,5.875002861023E-1)); -#37482=DIRECTION('',(-8.697566915162E-1,0.E0,-4.934807975624E-1)); -#37483=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#37484=AXIS2_PLACEMENT_3D('',#37481,#37482,#37483); -#37485=PLANE('',#37484); -#37486=ORIENTED_EDGE('',*,*,#25430,.F.); -#37488=ORIENTED_EDGE('',*,*,#37487,.T.); -#37489=ORIENTED_EDGE('',*,*,#28910,.T.); -#37490=ORIENTED_EDGE('',*,*,#37474,.F.); -#37491=EDGE_LOOP('',(#37486,#37488,#37489,#37490)); -#37492=FACE_OUTER_BOUND('',#37491,.F.); -#37494=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,5.124997138977E-1)); -#37495=DIRECTION('',(-6.611591372532E-1,0.E0,-7.502456899087E-1)); -#37496=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#37497=AXIS2_PLACEMENT_3D('',#37494,#37495,#37496); -#37498=PLANE('',#37497); -#37499=ORIENTED_EDGE('',*,*,#25428,.F.); -#37501=ORIENTED_EDGE('',*,*,#37500,.T.); -#37502=ORIENTED_EDGE('',*,*,#28912,.T.); -#37503=ORIENTED_EDGE('',*,*,#37487,.F.); -#37504=EDGE_LOOP('',(#37499,#37501,#37502,#37503)); -#37505=FACE_OUTER_BOUND('',#37504,.F.); -#37507=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,4.9375E-1)); -#37508=DIRECTION('',(-2.151497590808E-1,0.E0,-9.765810673812E-1)); -#37509=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#37510=AXIS2_PLACEMENT_3D('',#37507,#37508,#37509); -#37511=PLANE('',#37510); -#37512=ORIENTED_EDGE('',*,*,#25426,.F.); -#37514=ORIENTED_EDGE('',*,*,#37513,.T.); -#37515=ORIENTED_EDGE('',*,*,#28914,.T.); -#37516=ORIENTED_EDGE('',*,*,#37500,.F.); -#37517=EDGE_LOOP('',(#37512,#37514,#37515,#37516)); -#37518=FACE_OUTER_BOUND('',#37517,.F.); -#37520=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,4.9375E-1)); -#37521=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37522=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37523=AXIS2_PLACEMENT_3D('',#37520,#37521,#37522); -#37524=PLANE('',#37523); -#37525=ORIENTED_EDGE('',*,*,#25424,.F.); -#37527=ORIENTED_EDGE('',*,*,#37526,.T.); -#37528=ORIENTED_EDGE('',*,*,#28916,.T.); -#37529=ORIENTED_EDGE('',*,*,#37513,.F.); -#37530=EDGE_LOOP('',(#37525,#37527,#37528,#37529)); -#37531=FACE_OUTER_BOUND('',#37530,.F.); -#37533=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,5.124997138977E-1)); -#37534=DIRECTION('',(2.151497590808E-1,0.E0,-9.765810673812E-1)); -#37535=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#37536=AXIS2_PLACEMENT_3D('',#37533,#37534,#37535); -#37537=PLANE('',#37536); -#37538=ORIENTED_EDGE('',*,*,#25422,.F.); -#37540=ORIENTED_EDGE('',*,*,#37539,.T.); -#37541=ORIENTED_EDGE('',*,*,#28918,.T.); -#37542=ORIENTED_EDGE('',*,*,#37526,.F.); -#37543=EDGE_LOOP('',(#37538,#37540,#37541,#37542)); -#37544=FACE_OUTER_BOUND('',#37543,.F.); -#37546=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,5.5E-1)); -#37547=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#37548=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#37549=AXIS2_PLACEMENT_3D('',#37546,#37547,#37548); -#37550=PLANE('',#37549); -#37551=ORIENTED_EDGE('',*,*,#25420,.F.); -#37553=ORIENTED_EDGE('',*,*,#37552,.T.); -#37554=ORIENTED_EDGE('',*,*,#28920,.T.); -#37555=ORIENTED_EDGE('',*,*,#37539,.F.); -#37556=EDGE_LOOP('',(#37551,#37553,#37554,#37555)); -#37557=FACE_OUTER_BOUND('',#37556,.F.); -#37559=CARTESIAN_POINT('',(3.489361703396E0,1.55E0,6.249997138977E-1)); -#37560=DIRECTION('',(7.615382075403E-1,0.E0,-6.481200185586E-1)); -#37561=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#37562=AXIS2_PLACEMENT_3D('',#37559,#37560,#37561); -#37563=PLANE('',#37562); -#37564=ORIENTED_EDGE('',*,*,#25418,.F.); -#37566=ORIENTED_EDGE('',*,*,#37565,.T.); -#37567=ORIENTED_EDGE('',*,*,#28922,.T.); -#37568=ORIENTED_EDGE('',*,*,#37552,.F.); -#37569=EDGE_LOOP('',(#37564,#37566,#37567,#37568)); -#37570=FACE_OUTER_BOUND('',#37569,.F.); -#37572=CARTESIAN_POINT('',(3.531914889812E0,1.55E0,5.312502861023E-1)); -#37573=DIRECTION('',(-9.105865832266E-1,0.E0,-4.133183693567E-1)); -#37574=DIRECTION('',(-4.133183693567E-1,0.E0,9.105865832266E-1)); -#37575=AXIS2_PLACEMENT_3D('',#37572,#37573,#37574); -#37576=PLANE('',#37575); -#37577=ORIENTED_EDGE('',*,*,#25416,.F.); -#37579=ORIENTED_EDGE('',*,*,#37578,.T.); -#37580=ORIENTED_EDGE('',*,*,#28924,.T.); -#37581=ORIENTED_EDGE('',*,*,#37565,.F.); -#37582=EDGE_LOOP('',(#37577,#37579,#37580,#37581)); -#37583=FACE_OUTER_BOUND('',#37582,.F.); -#37585=CARTESIAN_POINT('',(3.595744669437E0,1.55E0,4.9375E-1)); -#37586=DIRECTION('',(-5.065519665348E-1,0.E0,-8.622094323305E-1)); -#37587=DIRECTION('',(-8.622094323305E-1,0.E0,5.065519665348E-1)); -#37588=AXIS2_PLACEMENT_3D('',#37585,#37586,#37587); -#37589=PLANE('',#37588); -#37590=ORIENTED_EDGE('',*,*,#25414,.F.); -#37592=ORIENTED_EDGE('',*,*,#37591,.T.); -#37593=ORIENTED_EDGE('',*,*,#28926,.T.); -#37594=ORIENTED_EDGE('',*,*,#37578,.F.); -#37595=EDGE_LOOP('',(#37590,#37592,#37593,#37594)); -#37596=FACE_OUTER_BOUND('',#37595,.F.); -#37598=CARTESIAN_POINT('',(3.680851072073E0,1.55E0,4.750002861023E-1)); -#37599=DIRECTION('',(-2.151496872277E-1,0.E0,-9.765810832111E-1)); -#37600=DIRECTION('',(-9.765810832111E-1,0.E0,2.151496872277E-1)); -#37601=AXIS2_PLACEMENT_3D('',#37598,#37599,#37600); -#37602=PLANE('',#37601); -#37603=ORIENTED_EDGE('',*,*,#25412,.F.); -#37605=ORIENTED_EDGE('',*,*,#37604,.T.); -#37606=ORIENTED_EDGE('',*,*,#28928,.T.); -#37607=ORIENTED_EDGE('',*,*,#37591,.F.); -#37608=EDGE_LOOP('',(#37603,#37605,#37606,#37607)); -#37609=FACE_OUTER_BOUND('',#37608,.F.); -#37611=CARTESIAN_POINT('',(3.765957444906E0,1.55E0,4.750002861023E-1)); -#37612=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37613=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37614=AXIS2_PLACEMENT_3D('',#37611,#37612,#37613); -#37615=PLANE('',#37614); -#37616=ORIENTED_EDGE('',*,*,#25410,.F.); -#37618=ORIENTED_EDGE('',*,*,#37617,.T.); -#37619=ORIENTED_EDGE('',*,*,#28930,.T.); -#37620=ORIENTED_EDGE('',*,*,#37604,.F.); -#37621=EDGE_LOOP('',(#37616,#37618,#37619,#37620)); -#37622=FACE_OUTER_BOUND('',#37621,.F.); -#37624=CARTESIAN_POINT('',(3.829787239432E0,1.55E0,4.9375E-1)); -#37625=DIRECTION('',(2.818376608812E-1,0.E0,-9.594621060308E-1)); -#37626=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#37627=AXIS2_PLACEMENT_3D('',#37624,#37625,#37626); -#37628=PLANE('',#37627); -#37629=ORIENTED_EDGE('',*,*,#25408,.F.); -#37630=ORIENTED_EDGE('',*,*,#36904,.T.); -#37631=ORIENTED_EDGE('',*,*,#28932,.T.); -#37632=ORIENTED_EDGE('',*,*,#37617,.F.); -#37633=EDGE_LOOP('',(#37629,#37630,#37631,#37632)); -#37634=FACE_OUTER_BOUND('',#37633,.F.); -#37636=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,3.25E-1)); -#37637=DIRECTION('',(0.E0,0.E0,1.E0)); -#37638=DIRECTION('',(1.E0,0.E0,0.E0)); -#37639=AXIS2_PLACEMENT_3D('',#37636,#37637,#37638); -#37640=PLANE('',#37639); -#37641=ORIENTED_EDGE('',*,*,#25522,.F.); -#37643=ORIENTED_EDGE('',*,*,#37642,.T.); -#37644=ORIENTED_EDGE('',*,*,#28949,.T.); -#37646=ORIENTED_EDGE('',*,*,#37645,.F.); -#37647=EDGE_LOOP('',(#37641,#37643,#37644,#37646)); -#37648=FACE_OUTER_BOUND('',#37647,.F.); -#37650=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-1.999997138977E-1)); -#37651=DIRECTION('',(-7.024653007554E-1,0.E0,7.117179927714E-1)); -#37652=DIRECTION('',(7.117179927714E-1,0.E0,7.024653007554E-1)); -#37653=AXIS2_PLACEMENT_3D('',#37650,#37651,#37652); -#37654=PLANE('',#37653); -#37655=ORIENTED_EDGE('',*,*,#25576,.F.); -#37657=ORIENTED_EDGE('',*,*,#37656,.T.); -#37658=ORIENTED_EDGE('',*,*,#28951,.T.); -#37659=ORIENTED_EDGE('',*,*,#37642,.F.); -#37660=EDGE_LOOP('',(#37655,#37657,#37658,#37659)); -#37661=FACE_OUTER_BOUND('',#37660,.F.); -#37663=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-2.375E-1)); -#37664=DIRECTION('',(-4.032203477633E-1,0.E0,9.151029183374E-1)); -#37665=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#37666=AXIS2_PLACEMENT_3D('',#37663,#37664,#37665); -#37667=PLANE('',#37666); -#37668=ORIENTED_EDGE('',*,*,#25574,.F.); -#37670=ORIENTED_EDGE('',*,*,#37669,.T.); -#37671=ORIENTED_EDGE('',*,*,#28953,.T.); -#37672=ORIENTED_EDGE('',*,*,#37656,.F.); -#37673=EDGE_LOOP('',(#37668,#37670,#37671,#37672)); -#37674=FACE_OUTER_BOUND('',#37673,.F.); -#37676=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-2.375E-1)); -#37677=DIRECTION('',(0.E0,0.E0,1.E0)); -#37678=DIRECTION('',(1.E0,0.E0,0.E0)); -#37679=AXIS2_PLACEMENT_3D('',#37676,#37677,#37678); -#37680=PLANE('',#37679); -#37681=ORIENTED_EDGE('',*,*,#25572,.F.); -#37683=ORIENTED_EDGE('',*,*,#37682,.T.); -#37684=ORIENTED_EDGE('',*,*,#28955,.T.); -#37685=ORIENTED_EDGE('',*,*,#37669,.F.); -#37686=EDGE_LOOP('',(#37681,#37683,#37684,#37685)); -#37687=FACE_OUTER_BOUND('',#37686,.F.); -#37689=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,-1.999997138977E-1)); -#37690=DIRECTION('',(5.065519665348E-1,0.E0,8.622094323305E-1)); -#37691=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#37692=AXIS2_PLACEMENT_3D('',#37689,#37690,#37691); -#37693=PLANE('',#37692); -#37694=ORIENTED_EDGE('',*,*,#25570,.F.); -#37696=ORIENTED_EDGE('',*,*,#37695,.T.); -#37697=ORIENTED_EDGE('',*,*,#28957,.T.); -#37698=ORIENTED_EDGE('',*,*,#37682,.F.); -#37699=EDGE_LOOP('',(#37694,#37696,#37697,#37698)); -#37700=FACE_OUTER_BOUND('',#37699,.F.); -#37702=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,-1.437497138977E-1)); -#37703=DIRECTION('',(7.975044865770E-1,0.E0,6.033130148517E-1)); -#37704=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865770E-1)); -#37705=AXIS2_PLACEMENT_3D('',#37702,#37703,#37704); -#37706=PLANE('',#37705); -#37707=ORIENTED_EDGE('',*,*,#25568,.F.); -#37709=ORIENTED_EDGE('',*,*,#37708,.T.); -#37710=ORIENTED_EDGE('',*,*,#28959,.T.); -#37711=ORIENTED_EDGE('',*,*,#37695,.F.); -#37712=EDGE_LOOP('',(#37707,#37709,#37710,#37711)); -#37713=FACE_OUTER_BOUND('',#37712,.F.); -#37715=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,-5.000028610230E-2)); -#37716=DIRECTION('',(9.752004643543E-1,0.E0,2.213234156683E-1)); -#37717=DIRECTION('',(2.213234156683E-1,0.E0,-9.752004643543E-1)); -#37718=AXIS2_PLACEMENT_3D('',#37715,#37716,#37717); -#37719=PLANE('',#37718); -#37720=ORIENTED_EDGE('',*,*,#25566,.F.); -#37722=ORIENTED_EDGE('',*,*,#37721,.T.); -#37723=ORIENTED_EDGE('',*,*,#28961,.T.); -#37724=ORIENTED_EDGE('',*,*,#37708,.F.); -#37725=EDGE_LOOP('',(#37720,#37722,#37723,#37724)); -#37726=FACE_OUTER_BOUND('',#37725,.F.); -#37728=CARTESIAN_POINT('',(3.106382966042E0,1.55E0,2.500028610229E-2)); -#37729=DIRECTION('',(1.E0,0.E0,0.E0)); -#37730=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37731=AXIS2_PLACEMENT_3D('',#37728,#37729,#37730); -#37732=PLANE('',#37731); -#37733=ORIENTED_EDGE('',*,*,#25564,.F.); -#37735=ORIENTED_EDGE('',*,*,#37734,.T.); -#37736=ORIENTED_EDGE('',*,*,#28963,.T.); -#37737=ORIENTED_EDGE('',*,*,#37721,.F.); -#37738=EDGE_LOOP('',(#37733,#37735,#37736,#37737)); -#37739=FACE_OUTER_BOUND('',#37738,.F.); -#37741=CARTESIAN_POINT('',(3.127659559250E0,1.55E0,1.187497138977E-1)); -#37742=DIRECTION('',(9.752004643543E-1,0.E0,-2.213234156683E-1)); -#37743=DIRECTION('',(-2.213234156683E-1,0.E0,-9.752004643543E-1)); -#37744=AXIS2_PLACEMENT_3D('',#37741,#37742,#37743); -#37745=PLANE('',#37744); -#37746=ORIENTED_EDGE('',*,*,#25562,.F.); -#37748=ORIENTED_EDGE('',*,*,#37747,.T.); -#37749=ORIENTED_EDGE('',*,*,#28965,.T.); -#37750=ORIENTED_EDGE('',*,*,#37734,.F.); -#37751=EDGE_LOOP('',(#37746,#37748,#37749,#37750)); -#37752=FACE_OUTER_BOUND('',#37751,.F.); -#37754=CARTESIAN_POINT('',(3.170212745667E0,1.55E0,1.749997138977E-1)); -#37755=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#37756=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#37757=AXIS2_PLACEMENT_3D('',#37754,#37755,#37756); -#37758=PLANE('',#37757); -#37759=ORIENTED_EDGE('',*,*,#25560,.F.); -#37761=ORIENTED_EDGE('',*,*,#37760,.T.); -#37762=ORIENTED_EDGE('',*,*,#28967,.T.); -#37763=ORIENTED_EDGE('',*,*,#37747,.F.); -#37764=EDGE_LOOP('',(#37759,#37761,#37762,#37763)); -#37765=FACE_OUTER_BOUND('',#37764,.F.); -#37767=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,2.125E-1)); -#37768=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#37769=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#37770=AXIS2_PLACEMENT_3D('',#37767,#37768,#37769); -#37771=PLANE('',#37770); -#37772=ORIENTED_EDGE('',*,*,#25558,.F.); -#37774=ORIENTED_EDGE('',*,*,#37773,.T.); -#37775=ORIENTED_EDGE('',*,*,#28969,.T.); -#37776=ORIENTED_EDGE('',*,*,#37760,.F.); -#37777=EDGE_LOOP('',(#37772,#37774,#37775,#37776)); -#37778=FACE_OUTER_BOUND('',#37777,.F.); -#37780=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,3.062502861023E-1)); -#37781=DIRECTION('',(1.E0,0.E0,0.E0)); -#37782=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37783=AXIS2_PLACEMENT_3D('',#37780,#37781,#37782); -#37784=PLANE('',#37783); -#37785=ORIENTED_EDGE('',*,*,#25556,.F.); -#37787=ORIENTED_EDGE('',*,*,#37786,.T.); -#37788=ORIENTED_EDGE('',*,*,#28971,.T.); -#37789=ORIENTED_EDGE('',*,*,#37773,.F.); -#37790=EDGE_LOOP('',(#37785,#37787,#37788,#37789)); -#37791=FACE_OUTER_BOUND('',#37790,.F.); -#37793=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,2.874997138977E-1)); -#37794=DIRECTION('',(-2.151591520746E-1,0.E0,9.765789979713E-1)); -#37795=DIRECTION('',(9.765789979713E-1,0.E0,2.151591520746E-1)); -#37796=AXIS2_PLACEMENT_3D('',#37793,#37794,#37795); -#37797=PLANE('',#37796); -#37798=ORIENTED_EDGE('',*,*,#25554,.F.); -#37800=ORIENTED_EDGE('',*,*,#37799,.T.); -#37801=ORIENTED_EDGE('',*,*,#28973,.T.); -#37802=ORIENTED_EDGE('',*,*,#37786,.F.); -#37803=EDGE_LOOP('',(#37798,#37800,#37801,#37802)); -#37804=FACE_OUTER_BOUND('',#37803,.F.); -#37806=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,2.125E-1)); -#37807=DIRECTION('',(-6.611548783840E-1,0.E0,7.502494430448E-1)); -#37808=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#37809=AXIS2_PLACEMENT_3D('',#37806,#37807,#37808); -#37810=PLANE('',#37809); -#37811=ORIENTED_EDGE('',*,*,#25552,.F.); -#37813=ORIENTED_EDGE('',*,*,#37812,.T.); -#37814=ORIENTED_EDGE('',*,*,#28975,.T.); -#37815=ORIENTED_EDGE('',*,*,#37799,.F.); -#37816=EDGE_LOOP('',(#37811,#37813,#37814,#37815)); -#37817=FACE_OUTER_BOUND('',#37816,.F.); -#37819=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,1.375002861023E-1)); -#37820=DIRECTION('',(-8.697566915162E-1,0.E0,4.934807975624E-1)); -#37821=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#37822=AXIS2_PLACEMENT_3D('',#37819,#37820,#37821); -#37823=PLANE('',#37822); -#37824=ORIENTED_EDGE('',*,*,#25550,.F.); -#37826=ORIENTED_EDGE('',*,*,#37825,.T.); -#37827=ORIENTED_EDGE('',*,*,#28977,.T.); -#37828=ORIENTED_EDGE('',*,*,#37812,.F.); -#37829=EDGE_LOOP('',(#37824,#37826,#37827,#37828)); -#37830=FACE_OUTER_BOUND('',#37829,.F.); -#37832=CARTESIAN_POINT('',(3.E0,1.55E0,6.249713897704E-3)); -#37833=DIRECTION('',(-9.871141314609E-1,0.E0,1.600177848561E-1)); -#37834=DIRECTION('',(1.600177848561E-1,0.E0,9.871141314609E-1)); -#37835=AXIS2_PLACEMENT_3D('',#37832,#37833,#37834); -#37836=PLANE('',#37835); -#37837=ORIENTED_EDGE('',*,*,#25548,.F.); -#37839=ORIENTED_EDGE('',*,*,#37838,.T.); -#37840=ORIENTED_EDGE('',*,*,#28979,.T.); -#37841=ORIENTED_EDGE('',*,*,#37825,.F.); -#37842=EDGE_LOOP('',(#37837,#37839,#37840,#37841)); -#37843=FACE_OUTER_BOUND('',#37842,.F.); -#37845=CARTESIAN_POINT('',(3.E0,1.55E0,-6.875E-2)); -#37846=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37847=DIRECTION('',(0.E0,0.E0,1.E0)); -#37848=AXIS2_PLACEMENT_3D('',#37845,#37846,#37847); -#37849=PLANE('',#37848); -#37850=ORIENTED_EDGE('',*,*,#25546,.F.); -#37852=ORIENTED_EDGE('',*,*,#37851,.T.); -#37853=ORIENTED_EDGE('',*,*,#28981,.T.); -#37854=ORIENTED_EDGE('',*,*,#37838,.F.); -#37855=EDGE_LOOP('',(#37850,#37852,#37853,#37854)); -#37856=FACE_OUTER_BOUND('',#37855,.F.); -#37858=CARTESIAN_POINT('',(3.021276593208E0,1.55E0,-1.8125E-1)); -#37859=DIRECTION('',(-9.825817148807E-1,0.E0,-1.858310350350E-1)); -#37860=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#37861=AXIS2_PLACEMENT_3D('',#37858,#37859,#37860); -#37862=PLANE('',#37861); -#37863=ORIENTED_EDGE('',*,*,#25544,.F.); -#37865=ORIENTED_EDGE('',*,*,#37864,.T.); -#37866=ORIENTED_EDGE('',*,*,#28983,.T.); -#37867=ORIENTED_EDGE('',*,*,#37851,.F.); -#37868=EDGE_LOOP('',(#37863,#37865,#37866,#37867)); -#37869=FACE_OUTER_BOUND('',#37868,.F.); -#37871=CARTESIAN_POINT('',(3.063829779625E0,1.55E0,-2.562497138977E-1)); -#37872=DIRECTION('',(-8.697566915162E-1,0.E0,-4.934807975624E-1)); -#37873=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#37874=AXIS2_PLACEMENT_3D('',#37871,#37872,#37873); -#37875=PLANE('',#37874); -#37876=ORIENTED_EDGE('',*,*,#25542,.F.); -#37878=ORIENTED_EDGE('',*,*,#37877,.T.); -#37879=ORIENTED_EDGE('',*,*,#28985,.T.); -#37880=ORIENTED_EDGE('',*,*,#37864,.F.); -#37881=EDGE_LOOP('',(#37876,#37878,#37879,#37880)); -#37882=FACE_OUTER_BOUND('',#37881,.F.); -#37884=CARTESIAN_POINT('',(3.148936152458E0,1.55E0,-3.312502861023E-1)); -#37885=DIRECTION('',(-6.611591372532E-1,0.E0,-7.502456899087E-1)); -#37886=DIRECTION('',(-7.502456899087E-1,0.E0,6.611591372532E-1)); -#37887=AXIS2_PLACEMENT_3D('',#37884,#37885,#37886); -#37888=PLANE('',#37887); -#37889=ORIENTED_EDGE('',*,*,#25540,.F.); -#37891=ORIENTED_EDGE('',*,*,#37890,.T.); -#37892=ORIENTED_EDGE('',*,*,#28987,.T.); -#37893=ORIENTED_EDGE('',*,*,#37877,.F.); -#37894=EDGE_LOOP('',(#37889,#37891,#37892,#37893)); -#37895=FACE_OUTER_BOUND('',#37894,.F.); -#37897=CARTESIAN_POINT('',(3.234042525291E0,1.55E0,-3.5E-1)); -#37898=DIRECTION('',(-2.151497590808E-1,0.E0,-9.765810673812E-1)); -#37899=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#37900=AXIS2_PLACEMENT_3D('',#37897,#37898,#37899); -#37901=PLANE('',#37900); -#37902=ORIENTED_EDGE('',*,*,#25538,.F.); -#37904=ORIENTED_EDGE('',*,*,#37903,.T.); -#37905=ORIENTED_EDGE('',*,*,#28989,.T.); -#37906=ORIENTED_EDGE('',*,*,#37890,.F.); -#37907=EDGE_LOOP('',(#37902,#37904,#37905,#37906)); -#37908=FACE_OUTER_BOUND('',#37907,.F.); -#37910=CARTESIAN_POINT('',(3.276595771313E0,1.55E0,-3.5E-1)); -#37911=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37912=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37913=AXIS2_PLACEMENT_3D('',#37910,#37911,#37912); -#37914=PLANE('',#37913); -#37915=ORIENTED_EDGE('',*,*,#25536,.F.); -#37917=ORIENTED_EDGE('',*,*,#37916,.T.); -#37918=ORIENTED_EDGE('',*,*,#28991,.T.); -#37919=ORIENTED_EDGE('',*,*,#37903,.F.); -#37920=EDGE_LOOP('',(#37915,#37917,#37918,#37919)); -#37921=FACE_OUTER_BOUND('',#37920,.F.); -#37923=CARTESIAN_POINT('',(3.361702144146E0,1.55E0,-3.312502861023E-1)); -#37924=DIRECTION('',(2.151497590808E-1,0.E0,-9.765810673812E-1)); -#37925=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#37926=AXIS2_PLACEMENT_3D('',#37923,#37924,#37925); -#37927=PLANE('',#37926); -#37928=ORIENTED_EDGE('',*,*,#25534,.F.); -#37930=ORIENTED_EDGE('',*,*,#37929,.T.); -#37931=ORIENTED_EDGE('',*,*,#28993,.T.); -#37932=ORIENTED_EDGE('',*,*,#37916,.F.); -#37933=EDGE_LOOP('',(#37928,#37930,#37931,#37932)); -#37934=FACE_OUTER_BOUND('',#37933,.F.); -#37936=CARTESIAN_POINT('',(3.425531923771E0,1.55E0,-2.9375E-1)); -#37937=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#37938=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#37939=AXIS2_PLACEMENT_3D('',#37936,#37937,#37938); -#37940=PLANE('',#37939); -#37941=ORIENTED_EDGE('',*,*,#25532,.F.); -#37943=ORIENTED_EDGE('',*,*,#37942,.T.); -#37944=ORIENTED_EDGE('',*,*,#28995,.T.); -#37945=ORIENTED_EDGE('',*,*,#37929,.F.); -#37946=EDGE_LOOP('',(#37941,#37943,#37944,#37945)); -#37947=FACE_OUTER_BOUND('',#37946,.F.); -#37949=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,1.749997138977E-1)); -#37950=DIRECTION('',(7.076082458030E-1,0.E0,-7.066049606899E-1)); -#37951=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#37952=AXIS2_PLACEMENT_3D('',#37949,#37950,#37951); -#37953=PLANE('',#37952); -#37954=ORIENTED_EDGE('',*,*,#25530,.F.); -#37956=ORIENTED_EDGE('',*,*,#37955,.T.); -#37957=ORIENTED_EDGE('',*,*,#28997,.T.); -#37958=ORIENTED_EDGE('',*,*,#37942,.F.); -#37959=EDGE_LOOP('',(#37954,#37956,#37957,#37958)); -#37960=FACE_OUTER_BOUND('',#37959,.F.); -#37962=CARTESIAN_POINT('',(3.893617019057E0,1.55E0,-3.5E-1)); -#37963=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37964=DIRECTION('',(0.E0,0.E0,1.E0)); -#37965=AXIS2_PLACEMENT_3D('',#37962,#37963,#37964); -#37966=PLANE('',#37965); -#37967=ORIENTED_EDGE('',*,*,#25528,.F.); -#37969=ORIENTED_EDGE('',*,*,#37968,.T.); -#37970=ORIENTED_EDGE('',*,*,#28999,.T.); -#37971=ORIENTED_EDGE('',*,*,#37955,.F.); -#37972=EDGE_LOOP('',(#37967,#37969,#37970,#37971)); -#37973=FACE_OUTER_BOUND('',#37972,.F.); -#37975=CARTESIAN_POINT('',(4.E0,1.55E0,-3.5E-1)); -#37976=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37977=DIRECTION('',(-1.E0,0.E0,0.E0)); -#37978=AXIS2_PLACEMENT_3D('',#37975,#37976,#37977); -#37979=PLANE('',#37978); -#37980=ORIENTED_EDGE('',*,*,#25526,.F.); -#37982=ORIENTED_EDGE('',*,*,#37981,.T.); -#37983=ORIENTED_EDGE('',*,*,#29001,.T.); -#37984=ORIENTED_EDGE('',*,*,#37968,.F.); -#37985=EDGE_LOOP('',(#37980,#37982,#37983,#37984)); -#37986=FACE_OUTER_BOUND('',#37985,.F.); -#37988=CARTESIAN_POINT('',(4.E0,1.55E0,3.25E-1)); -#37989=DIRECTION('',(1.E0,0.E0,0.E0)); -#37990=DIRECTION('',(0.E0,0.E0,-1.E0)); -#37991=AXIS2_PLACEMENT_3D('',#37988,#37989,#37990); -#37992=PLANE('',#37991); -#37993=ORIENTED_EDGE('',*,*,#25524,.F.); -#37994=ORIENTED_EDGE('',*,*,#37645,.T.); -#37995=ORIENTED_EDGE('',*,*,#29003,.T.); -#37996=ORIENTED_EDGE('',*,*,#37981,.F.); -#37997=EDGE_LOOP('',(#37993,#37994,#37995,#37996)); -#37998=FACE_OUTER_BOUND('',#37997,.F.); -#38000=CARTESIAN_POINT('',(5.75E0,1.55E0,1.03375E1)); -#38001=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38002=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38003=AXIS2_PLACEMENT_3D('',#38000,#38001,#38002); -#38004=PLANE('',#38003); -#38005=ORIENTED_EDGE('',*,*,#25580,.F.); -#38007=ORIENTED_EDGE('',*,*,#38006,.T.); -#38008=ORIENTED_EDGE('',*,*,#29020,.T.); -#38010=ORIENTED_EDGE('',*,*,#38009,.F.); -#38011=EDGE_LOOP('',(#38005,#38007,#38008,#38010)); -#38012=FACE_OUTER_BOUND('',#38011,.F.); -#38014=CARTESIAN_POINT('',(5.75E0,1.55E0,1.045E1)); -#38015=DIRECTION('',(1.E0,0.E0,0.E0)); -#38016=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38017=AXIS2_PLACEMENT_3D('',#38014,#38015,#38016); -#38018=PLANE('',#38017); -#38019=ORIENTED_EDGE('',*,*,#25586,.F.); -#38021=ORIENTED_EDGE('',*,*,#38020,.T.); -#38022=ORIENTED_EDGE('',*,*,#29022,.T.); -#38023=ORIENTED_EDGE('',*,*,#38006,.F.); -#38024=EDGE_LOOP('',(#38019,#38021,#38022,#38023)); -#38025=FACE_OUTER_BOUND('',#38024,.F.); -#38027=CARTESIAN_POINT('',(4.75E0,1.55E0,1.045E1)); -#38028=DIRECTION('',(0.E0,0.E0,1.E0)); -#38029=DIRECTION('',(1.E0,0.E0,0.E0)); -#38030=AXIS2_PLACEMENT_3D('',#38027,#38028,#38029); -#38031=PLANE('',#38030); -#38032=ORIENTED_EDGE('',*,*,#25584,.F.); -#38034=ORIENTED_EDGE('',*,*,#38033,.T.); -#38035=ORIENTED_EDGE('',*,*,#29024,.T.); -#38036=ORIENTED_EDGE('',*,*,#38020,.F.); -#38037=EDGE_LOOP('',(#38032,#38034,#38035,#38036)); -#38038=FACE_OUTER_BOUND('',#38037,.F.); -#38040=CARTESIAN_POINT('',(4.75E0,1.55E0,1.03375E1)); -#38041=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38042=DIRECTION('',(0.E0,0.E0,1.E0)); -#38043=AXIS2_PLACEMENT_3D('',#38040,#38041,#38042); -#38044=PLANE('',#38043); -#38045=ORIENTED_EDGE('',*,*,#25582,.F.); -#38046=ORIENTED_EDGE('',*,*,#38009,.T.); -#38047=ORIENTED_EDGE('',*,*,#29026,.T.); -#38048=ORIENTED_EDGE('',*,*,#38033,.F.); -#38049=EDGE_LOOP('',(#38045,#38046,#38047,#38048)); -#38050=FACE_OUTER_BOUND('',#38049,.F.); -#38052=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.456250035763E0)); -#38053=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38054=DIRECTION('',(0.E0,0.E0,1.E0)); -#38055=AXIS2_PLACEMENT_3D('',#38052,#38053,#38054); -#38056=PLANE('',#38055); -#38057=ORIENTED_EDGE('',*,*,#25590,.F.); -#38059=ORIENTED_EDGE('',*,*,#38058,.T.); -#38060=ORIENTED_EDGE('',*,*,#29043,.T.); -#38062=ORIENTED_EDGE('',*,*,#38061,.F.); -#38063=EDGE_LOOP('',(#38057,#38059,#38060,#38062)); -#38064=FACE_OUTER_BOUND('',#38063,.F.); -#38066=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.474999964237E0)); -#38067=DIRECTION('',(1.735740053062E-1,0.E0,-9.848208287206E-1)); -#38068=DIRECTION('',(-9.848208287206E-1,0.E0,-1.735740053062E-1)); -#38069=AXIS2_PLACEMENT_3D('',#38066,#38067,#38068); -#38070=PLANE('',#38069); -#38071=ORIENTED_EDGE('',*,*,#25668,.F.); -#38073=ORIENTED_EDGE('',*,*,#38072,.T.); -#38074=ORIENTED_EDGE('',*,*,#29045,.T.); -#38075=ORIENTED_EDGE('',*,*,#38058,.F.); -#38076=EDGE_LOOP('',(#38071,#38073,#38074,#38075)); -#38077=FACE_OUTER_BOUND('',#38076,.F.); -#38079=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,9.55E0)); -#38080=DIRECTION('',(6.611564428881E-1,0.E0,-7.502480643277E-1)); -#38081=DIRECTION('',(-7.502480643277E-1,0.E0,-6.611564428881E-1)); -#38082=AXIS2_PLACEMENT_3D('',#38079,#38080,#38081); -#38083=PLANE('',#38082); -#38084=ORIENTED_EDGE('',*,*,#25666,.F.); -#38086=ORIENTED_EDGE('',*,*,#38085,.T.); -#38087=ORIENTED_EDGE('',*,*,#29047,.T.); -#38088=ORIENTED_EDGE('',*,*,#38072,.F.); -#38089=EDGE_LOOP('',(#38084,#38086,#38087,#38088)); -#38090=FACE_OUTER_BOUND('',#38089,.F.); -#38092=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.624999982119E0)); -#38093=DIRECTION('',(8.697574211798E-1,0.E0,-4.934795115328E-1)); -#38094=DIRECTION('',(-4.934795115328E-1,0.E0,-8.697574211798E-1)); -#38095=AXIS2_PLACEMENT_3D('',#38092,#38093,#38094); -#38096=PLANE('',#38095); -#38097=ORIENTED_EDGE('',*,*,#25664,.F.); -#38099=ORIENTED_EDGE('',*,*,#38098,.T.); -#38100=ORIENTED_EDGE('',*,*,#29049,.T.); -#38101=ORIENTED_EDGE('',*,*,#38085,.F.); -#38102=EDGE_LOOP('',(#38097,#38099,#38100,#38101)); -#38103=FACE_OUTER_BOUND('',#38102,.F.); -#38105=CARTESIAN_POINT('',(5.75E0,1.55E0,9.71875E0)); -#38106=DIRECTION('',(9.752007608434E-1,0.E0,-2.213221092673E-1)); -#38107=DIRECTION('',(-2.213221092673E-1,0.E0,-9.752007608434E-1)); -#38108=AXIS2_PLACEMENT_3D('',#38105,#38106,#38107); -#38109=PLANE('',#38108); -#38110=ORIENTED_EDGE('',*,*,#25662,.F.); -#38112=ORIENTED_EDGE('',*,*,#38111,.T.); -#38113=ORIENTED_EDGE('',*,*,#29051,.T.); -#38114=ORIENTED_EDGE('',*,*,#38098,.F.); -#38115=EDGE_LOOP('',(#38110,#38112,#38113,#38114)); -#38116=FACE_OUTER_BOUND('',#38115,.F.); -#38118=CARTESIAN_POINT('',(5.75E0,1.55E0,9.8875E0)); -#38119=DIRECTION('',(1.E0,0.E0,0.E0)); -#38120=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38121=AXIS2_PLACEMENT_3D('',#38118,#38119,#38120); -#38122=PLANE('',#38121); -#38123=ORIENTED_EDGE('',*,*,#25660,.F.); -#38125=ORIENTED_EDGE('',*,*,#38124,.T.); -#38126=ORIENTED_EDGE('',*,*,#29053,.T.); -#38127=ORIENTED_EDGE('',*,*,#38111,.F.); -#38128=EDGE_LOOP('',(#38123,#38125,#38126,#38127)); -#38129=FACE_OUTER_BOUND('',#38128,.F.); -#38131=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.981250017881E0)); -#38132=DIRECTION('',(9.752007608434E-1,0.E0,2.213221092673E-1)); -#38133=DIRECTION('',(2.213221092673E-1,0.E0,-9.752007608434E-1)); -#38134=AXIS2_PLACEMENT_3D('',#38131,#38132,#38133); -#38135=PLANE('',#38134); -#38136=ORIENTED_EDGE('',*,*,#25658,.F.); -#38138=ORIENTED_EDGE('',*,*,#38137,.T.); -#38139=ORIENTED_EDGE('',*,*,#29055,.T.); -#38140=ORIENTED_EDGE('',*,*,#38124,.F.); -#38141=EDGE_LOOP('',(#38136,#38138,#38139,#38140)); -#38142=FACE_OUTER_BOUND('',#38141,.F.); -#38144=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.005625E1)); -#38145=DIRECTION('',(8.697574211798E-1,0.E0,4.934795115328E-1)); -#38146=DIRECTION('',(4.934795115328E-1,0.E0,-8.697574211798E-1)); -#38147=AXIS2_PLACEMENT_3D('',#38144,#38145,#38146); -#38148=PLANE('',#38147); -#38149=ORIENTED_EDGE('',*,*,#25656,.F.); -#38151=ORIENTED_EDGE('',*,*,#38150,.T.); -#38152=ORIENTED_EDGE('',*,*,#29057,.T.); -#38153=ORIENTED_EDGE('',*,*,#38137,.F.); -#38154=EDGE_LOOP('',(#38149,#38151,#38152,#38153)); -#38155=FACE_OUTER_BOUND('',#38154,.F.); -#38157=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.013125000894E1)); -#38158=DIRECTION('',(6.611563097982E-1,0.E0,7.502481816133E-1)); -#38159=DIRECTION('',(7.502481816133E-1,0.E0,-6.611563097982E-1)); -#38160=AXIS2_PLACEMENT_3D('',#38157,#38158,#38159); -#38161=PLANE('',#38160); -#38162=ORIENTED_EDGE('',*,*,#25654,.F.); -#38164=ORIENTED_EDGE('',*,*,#38163,.T.); -#38165=ORIENTED_EDGE('',*,*,#29059,.T.); -#38166=ORIENTED_EDGE('',*,*,#38150,.F.); -#38167=EDGE_LOOP('',(#38162,#38164,#38165,#38166)); -#38168=FACE_OUTER_BOUND('',#38167,.F.); -#38170=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.016875E1)); -#38171=DIRECTION('',(4.032176319956E-1,0.E0,9.151041149770E-1)); -#38172=DIRECTION('',(9.151041149770E-1,0.E0,-4.032176319956E-1)); -#38173=AXIS2_PLACEMENT_3D('',#38170,#38171,#38172); -#38174=PLANE('',#38173); -#38175=ORIENTED_EDGE('',*,*,#25652,.F.); -#38177=ORIENTED_EDGE('',*,*,#38176,.T.); -#38178=ORIENTED_EDGE('',*,*,#29061,.T.); -#38179=ORIENTED_EDGE('',*,*,#38163,.F.); -#38180=EDGE_LOOP('',(#38175,#38177,#38178,#38179)); -#38181=FACE_OUTER_BOUND('',#38180,.F.); -#38183=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.018750000894E1)); -#38184=DIRECTION('',(1.735747513456E-1,0.E0,9.848206972314E-1)); -#38185=DIRECTION('',(9.848206972314E-1,0.E0,-1.735747513456E-1)); -#38186=AXIS2_PLACEMENT_3D('',#38183,#38184,#38185); -#38187=PLANE('',#38186); -#38188=ORIENTED_EDGE('',*,*,#25650,.F.); -#38190=ORIENTED_EDGE('',*,*,#38189,.T.); -#38191=ORIENTED_EDGE('',*,*,#29063,.T.); -#38192=ORIENTED_EDGE('',*,*,#38176,.F.); -#38193=EDGE_LOOP('',(#38188,#38190,#38191,#38192)); -#38194=FACE_OUTER_BOUND('',#38193,.F.); -#38196=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.018750000894E1)); -#38197=DIRECTION('',(0.E0,0.E0,1.E0)); -#38198=DIRECTION('',(1.E0,0.E0,0.E0)); -#38199=AXIS2_PLACEMENT_3D('',#38196,#38197,#38198); -#38200=PLANE('',#38199); -#38201=ORIENTED_EDGE('',*,*,#25648,.F.); -#38203=ORIENTED_EDGE('',*,*,#38202,.T.); -#38204=ORIENTED_EDGE('',*,*,#29065,.T.); -#38205=ORIENTED_EDGE('',*,*,#38189,.F.); -#38206=EDGE_LOOP('',(#38201,#38203,#38204,#38205)); -#38207=FACE_OUTER_BOUND('',#38206,.F.); -#38209=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.016875E1)); -#38210=DIRECTION('',(-1.735746570245E-1,0.E0,9.848207138555E-1)); -#38211=DIRECTION('',(9.848207138555E-1,0.E0,1.735746570245E-1)); -#38212=AXIS2_PLACEMENT_3D('',#38209,#38210,#38211); -#38213=PLANE('',#38212); -#38214=ORIENTED_EDGE('',*,*,#25646,.F.); -#38216=ORIENTED_EDGE('',*,*,#38215,.T.); -#38217=ORIENTED_EDGE('',*,*,#29067,.T.); -#38218=ORIENTED_EDGE('',*,*,#38202,.F.); -#38219=EDGE_LOOP('',(#38214,#38216,#38217,#38218)); -#38220=FACE_OUTER_BOUND('',#38219,.F.); -#38222=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.013125000894E1)); -#38223=DIRECTION('',(-4.032176911162E-1,0.E0,9.151040889270E-1)); -#38224=DIRECTION('',(9.151040889270E-1,0.E0,4.032176911162E-1)); -#38225=AXIS2_PLACEMENT_3D('',#38222,#38223,#38224); -#38226=PLANE('',#38225); -#38227=ORIENTED_EDGE('',*,*,#25644,.F.); -#38229=ORIENTED_EDGE('',*,*,#38228,.T.); -#38230=ORIENTED_EDGE('',*,*,#29069,.T.); -#38231=ORIENTED_EDGE('',*,*,#38215,.F.); -#38232=EDGE_LOOP('',(#38227,#38229,#38230,#38231)); -#38233=FACE_OUTER_BOUND('',#38232,.F.); -#38235=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.005625E1)); -#38236=DIRECTION('',(-6.611563423775E-1,0.E0,7.502481529028E-1)); -#38237=DIRECTION('',(7.502481529028E-1,0.E0,6.611563423775E-1)); -#38238=AXIS2_PLACEMENT_3D('',#38235,#38236,#38237); -#38239=PLANE('',#38238); -#38240=ORIENTED_EDGE('',*,*,#25642,.F.); -#38242=ORIENTED_EDGE('',*,*,#38241,.T.); -#38243=ORIENTED_EDGE('',*,*,#29071,.T.); -#38244=ORIENTED_EDGE('',*,*,#38228,.F.); -#38245=EDGE_LOOP('',(#38240,#38242,#38243,#38244)); -#38246=FACE_OUTER_BOUND('',#38245,.F.); -#38248=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.981250017881E0)); -#38249=DIRECTION('',(-8.697574489933E-1,0.E0,4.934794625115E-1)); -#38250=DIRECTION('',(4.934794625115E-1,0.E0,8.697574489933E-1)); -#38251=AXIS2_PLACEMENT_3D('',#38248,#38249,#38250); -#38252=PLANE('',#38251); -#38253=ORIENTED_EDGE('',*,*,#25640,.F.); -#38255=ORIENTED_EDGE('',*,*,#38254,.T.); -#38256=ORIENTED_EDGE('',*,*,#29073,.T.); -#38257=ORIENTED_EDGE('',*,*,#38241,.F.); -#38258=EDGE_LOOP('',(#38253,#38255,#38256,#38257)); -#38259=FACE_OUTER_BOUND('',#38258,.F.); -#38261=CARTESIAN_POINT('',(4.75E0,1.55E0,9.8875E0)); -#38262=DIRECTION('',(-9.752007650252E-1,0.E0,2.213220908409E-1)); -#38263=DIRECTION('',(2.213220908409E-1,0.E0,9.752007650252E-1)); -#38264=AXIS2_PLACEMENT_3D('',#38261,#38262,#38263); -#38265=PLANE('',#38264); -#38266=ORIENTED_EDGE('',*,*,#25638,.F.); -#38268=ORIENTED_EDGE('',*,*,#38267,.T.); -#38269=ORIENTED_EDGE('',*,*,#29075,.T.); -#38270=ORIENTED_EDGE('',*,*,#38254,.F.); -#38271=EDGE_LOOP('',(#38266,#38268,#38269,#38270)); -#38272=FACE_OUTER_BOUND('',#38271,.F.); -#38274=CARTESIAN_POINT('',(4.75E0,1.55E0,9.71875E0)); -#38275=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38276=DIRECTION('',(0.E0,0.E0,1.E0)); -#38277=AXIS2_PLACEMENT_3D('',#38274,#38275,#38276); -#38278=PLANE('',#38277); -#38279=ORIENTED_EDGE('',*,*,#25636,.F.); -#38281=ORIENTED_EDGE('',*,*,#38280,.T.); -#38282=ORIENTED_EDGE('',*,*,#29077,.T.); -#38283=ORIENTED_EDGE('',*,*,#38267,.F.); -#38284=EDGE_LOOP('',(#38279,#38281,#38282,#38283)); -#38285=FACE_OUTER_BOUND('',#38284,.F.); -#38287=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.624999982119E0)); -#38288=DIRECTION('',(-9.752007650252E-1,0.E0,-2.213220908409E-1)); -#38289=DIRECTION('',(-2.213220908409E-1,0.E0,9.752007650252E-1)); -#38290=AXIS2_PLACEMENT_3D('',#38287,#38288,#38289); -#38291=PLANE('',#38290); -#38292=ORIENTED_EDGE('',*,*,#25634,.F.); -#38294=ORIENTED_EDGE('',*,*,#38293,.T.); -#38295=ORIENTED_EDGE('',*,*,#29079,.T.); -#38296=ORIENTED_EDGE('',*,*,#38280,.F.); -#38297=EDGE_LOOP('',(#38292,#38294,#38295,#38296)); -#38298=FACE_OUTER_BOUND('',#38297,.F.); -#38300=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,9.55E0)); -#38301=DIRECTION('',(-8.697574489933E-1,0.E0,-4.934794625115E-1)); -#38302=DIRECTION('',(-4.934794625115E-1,0.E0,8.697574489933E-1)); -#38303=AXIS2_PLACEMENT_3D('',#38300,#38301,#38302); -#38304=PLANE('',#38303); -#38305=ORIENTED_EDGE('',*,*,#25632,.F.); -#38307=ORIENTED_EDGE('',*,*,#38306,.T.); -#38308=ORIENTED_EDGE('',*,*,#29081,.T.); -#38309=ORIENTED_EDGE('',*,*,#38293,.F.); -#38310=EDGE_LOOP('',(#38305,#38307,#38308,#38309)); -#38311=FACE_OUTER_BOUND('',#38310,.F.); -#38313=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.474999964237E0)); -#38314=DIRECTION('',(-6.611564754674E-1,0.E0,-7.502480356172E-1)); -#38315=DIRECTION('',(-7.502480356172E-1,0.E0,6.611564754674E-1)); -#38316=AXIS2_PLACEMENT_3D('',#38313,#38314,#38315); -#38317=PLANE('',#38316); -#38318=ORIENTED_EDGE('',*,*,#25630,.F.); -#38320=ORIENTED_EDGE('',*,*,#38319,.T.); -#38321=ORIENTED_EDGE('',*,*,#29083,.T.); -#38322=ORIENTED_EDGE('',*,*,#38306,.F.); -#38323=EDGE_LOOP('',(#38318,#38320,#38321,#38322)); -#38324=FACE_OUTER_BOUND('',#38323,.F.); -#38326=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.456250035763E0)); -#38327=DIRECTION('',(-1.735739345657E-1,0.E0,-9.848208411886E-1)); -#38328=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#38329=AXIS2_PLACEMENT_3D('',#38326,#38327,#38328); -#38330=PLANE('',#38329); -#38331=ORIENTED_EDGE('',*,*,#25628,.F.); -#38333=ORIENTED_EDGE('',*,*,#38332,.T.); -#38334=ORIENTED_EDGE('',*,*,#29085,.T.); -#38335=ORIENTED_EDGE('',*,*,#38319,.F.); -#38336=EDGE_LOOP('',(#38331,#38333,#38334,#38335)); -#38337=FACE_OUTER_BOUND('',#38336,.F.); -#38339=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,9.568749982119E0)); -#38340=DIRECTION('',(1.E0,0.E0,0.E0)); -#38341=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38342=AXIS2_PLACEMENT_3D('',#38339,#38340,#38341); -#38343=PLANE('',#38342); -#38344=ORIENTED_EDGE('',*,*,#25626,.F.); -#38346=ORIENTED_EDGE('',*,*,#38345,.T.); -#38347=ORIENTED_EDGE('',*,*,#29087,.T.); -#38348=ORIENTED_EDGE('',*,*,#38332,.F.); -#38349=EDGE_LOOP('',(#38344,#38346,#38347,#38348)); -#38350=FACE_OUTER_BOUND('',#38349,.F.); -#38352=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,9.587500017881E0)); -#38353=DIRECTION('',(2.818419329952E-1,0.E0,9.594608511063E-1)); -#38354=DIRECTION('',(9.594608511063E-1,0.E0,-2.818419329952E-1)); -#38355=AXIS2_PLACEMENT_3D('',#38352,#38353,#38354); -#38356=PLANE('',#38355); -#38357=ORIENTED_EDGE('',*,*,#25624,.F.); -#38359=ORIENTED_EDGE('',*,*,#38358,.T.); -#38360=ORIENTED_EDGE('',*,*,#29089,.T.); -#38361=ORIENTED_EDGE('',*,*,#38345,.F.); -#38362=EDGE_LOOP('',(#38357,#38359,#38360,#38361)); -#38363=FACE_OUTER_BOUND('',#38362,.F.); -#38365=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.643750017881E0)); -#38366=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#38367=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#38368=AXIS2_PLACEMENT_3D('',#38365,#38366,#38367); -#38369=PLANE('',#38368); -#38370=ORIENTED_EDGE('',*,*,#25622,.F.); -#38372=ORIENTED_EDGE('',*,*,#38371,.T.); -#38373=ORIENTED_EDGE('',*,*,#29091,.T.); -#38374=ORIENTED_EDGE('',*,*,#38358,.F.); -#38375=EDGE_LOOP('',(#38370,#38372,#38373,#38374)); -#38376=FACE_OUTER_BOUND('',#38375,.F.); -#38378=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.71875E0)); -#38379=DIRECTION('',(9.620371902713E-1,0.E0,2.729183843844E-1)); -#38380=DIRECTION('',(2.729183843844E-1,0.E0,-9.620371902713E-1)); -#38381=AXIS2_PLACEMENT_3D('',#38378,#38379,#38380); -#38382=PLANE('',#38381); -#38383=ORIENTED_EDGE('',*,*,#25620,.F.); -#38385=ORIENTED_EDGE('',*,*,#38384,.T.); -#38386=ORIENTED_EDGE('',*,*,#29093,.T.); -#38387=ORIENTED_EDGE('',*,*,#38371,.F.); -#38388=EDGE_LOOP('',(#38383,#38385,#38386,#38387)); -#38389=FACE_OUTER_BOUND('',#38388,.F.); -#38391=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.8875E0)); -#38392=DIRECTION('',(1.E0,0.E0,0.E0)); -#38393=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38394=AXIS2_PLACEMENT_3D('',#38391,#38392,#38393); -#38395=PLANE('',#38394); -#38396=ORIENTED_EDGE('',*,*,#25618,.F.); -#38398=ORIENTED_EDGE('',*,*,#38397,.T.); -#38399=ORIENTED_EDGE('',*,*,#29095,.T.); -#38400=ORIENTED_EDGE('',*,*,#38384,.F.); -#38401=EDGE_LOOP('',(#38396,#38398,#38399,#38400)); -#38402=FACE_OUTER_BOUND('',#38401,.F.); -#38404=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,9.962499982119E0)); -#38405=DIRECTION('',(9.620371902713E-1,0.E0,-2.729183843844E-1)); -#38406=DIRECTION('',(-2.729183843844E-1,0.E0,-9.620371902713E-1)); -#38407=AXIS2_PLACEMENT_3D('',#38404,#38405,#38406); -#38408=PLANE('',#38407); -#38409=ORIENTED_EDGE('',*,*,#25616,.F.); -#38411=ORIENTED_EDGE('',*,*,#38410,.T.); -#38412=ORIENTED_EDGE('',*,*,#29097,.T.); -#38413=ORIENTED_EDGE('',*,*,#38397,.F.); -#38414=EDGE_LOOP('',(#38409,#38411,#38412,#38413)); -#38415=FACE_OUTER_BOUND('',#38414,.F.); -#38417=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.001875000894E1)); -#38418=DIRECTION('',(7.975046249937E-1,0.E0,-6.033128318821E-1)); -#38419=DIRECTION('',(-6.033128318821E-1,0.E0,-7.975046249937E-1)); -#38420=AXIS2_PLACEMENT_3D('',#38417,#38418,#38419); -#38421=PLANE('',#38420); -#38422=ORIENTED_EDGE('',*,*,#25614,.F.); -#38424=ORIENTED_EDGE('',*,*,#38423,.T.); -#38425=ORIENTED_EDGE('',*,*,#29099,.T.); -#38426=ORIENTED_EDGE('',*,*,#38410,.F.); -#38427=EDGE_LOOP('',(#38422,#38424,#38425,#38426)); -#38428=FACE_OUTER_BOUND('',#38427,.F.); -#38430=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.005625E1)); -#38431=DIRECTION('',(5.065486520942E-1,0.E0,-8.622113795709E-1)); -#38432=DIRECTION('',(-8.622113795709E-1,0.E0,-5.065486520942E-1)); -#38433=AXIS2_PLACEMENT_3D('',#38430,#38431,#38432); -#38434=PLANE('',#38433); -#38435=ORIENTED_EDGE('',*,*,#25612,.F.); -#38437=ORIENTED_EDGE('',*,*,#38436,.T.); -#38438=ORIENTED_EDGE('',*,*,#29101,.T.); -#38439=ORIENTED_EDGE('',*,*,#38423,.F.); -#38440=EDGE_LOOP('',(#38435,#38437,#38438,#38439)); -#38441=FACE_OUTER_BOUND('',#38440,.F.); -#38443=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,1.007500000894E1)); -#38444=DIRECTION('',(2.151529879292E-1,0.E0,-9.765803560308E-1)); -#38445=DIRECTION('',(-9.765803560308E-1,0.E0,-2.151529879292E-1)); -#38446=AXIS2_PLACEMENT_3D('',#38443,#38444,#38445); -#38447=PLANE('',#38446); -#38448=ORIENTED_EDGE('',*,*,#25610,.F.); -#38450=ORIENTED_EDGE('',*,*,#38449,.T.); -#38451=ORIENTED_EDGE('',*,*,#29103,.T.); -#38452=ORIENTED_EDGE('',*,*,#38436,.F.); -#38453=EDGE_LOOP('',(#38448,#38450,#38451,#38452)); -#38454=FACE_OUTER_BOUND('',#38453,.F.); -#38456=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,1.007500000894E1)); -#38457=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38458=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38459=AXIS2_PLACEMENT_3D('',#38456,#38457,#38458); -#38460=PLANE('',#38459); -#38461=ORIENTED_EDGE('',*,*,#25608,.F.); -#38463=ORIENTED_EDGE('',*,*,#38462,.T.); -#38464=ORIENTED_EDGE('',*,*,#29105,.T.); -#38465=ORIENTED_EDGE('',*,*,#38449,.F.); -#38466=EDGE_LOOP('',(#38461,#38463,#38464,#38465)); -#38467=FACE_OUTER_BOUND('',#38466,.F.); -#38469=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.005625E1)); -#38470=DIRECTION('',(-2.151529879292E-1,0.E0,-9.765803560308E-1)); -#38471=DIRECTION('',(-9.765803560308E-1,0.E0,2.151529879292E-1)); -#38472=AXIS2_PLACEMENT_3D('',#38469,#38470,#38471); -#38473=PLANE('',#38472); -#38474=ORIENTED_EDGE('',*,*,#25606,.F.); -#38476=ORIENTED_EDGE('',*,*,#38475,.T.); -#38477=ORIENTED_EDGE('',*,*,#29107,.T.); -#38478=ORIENTED_EDGE('',*,*,#38462,.F.); -#38479=EDGE_LOOP('',(#38474,#38476,#38477,#38478)); -#38480=FACE_OUTER_BOUND('',#38479,.F.); -#38482=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.001875000894E1)); -#38483=DIRECTION('',(-5.065490037399E-1,0.E0,-8.622111729792E-1)); -#38484=DIRECTION('',(-8.622111729792E-1,0.E0,5.065490037399E-1)); -#38485=AXIS2_PLACEMENT_3D('',#38482,#38483,#38484); -#38486=PLANE('',#38485); -#38487=ORIENTED_EDGE('',*,*,#25604,.F.); -#38489=ORIENTED_EDGE('',*,*,#38488,.T.); -#38490=ORIENTED_EDGE('',*,*,#29109,.T.); -#38491=ORIENTED_EDGE('',*,*,#38475,.F.); -#38492=EDGE_LOOP('',(#38487,#38489,#38490,#38491)); -#38493=FACE_OUTER_BOUND('',#38492,.F.); -#38495=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.962499982119E0)); -#38496=DIRECTION('',(-7.975045233440E-1,0.E0,-6.033129662504E-1)); -#38497=DIRECTION('',(-6.033129662504E-1,0.E0,7.975045233440E-1)); -#38498=AXIS2_PLACEMENT_3D('',#38495,#38496,#38497); -#38499=PLANE('',#38498); -#38500=ORIENTED_EDGE('',*,*,#25602,.F.); -#38502=ORIENTED_EDGE('',*,*,#38501,.T.); -#38503=ORIENTED_EDGE('',*,*,#29111,.T.); -#38504=ORIENTED_EDGE('',*,*,#38488,.F.); -#38505=EDGE_LOOP('',(#38500,#38502,#38503,#38504)); -#38506=FACE_OUTER_BOUND('',#38505,.F.); -#38508=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.8875E0)); -#38509=DIRECTION('',(-9.620371902713E-1,0.E0,-2.729183843844E-1)); -#38510=DIRECTION('',(-2.729183843844E-1,0.E0,9.620371902713E-1)); -#38511=AXIS2_PLACEMENT_3D('',#38508,#38509,#38510); -#38512=PLANE('',#38511); -#38513=ORIENTED_EDGE('',*,*,#25600,.F.); -#38515=ORIENTED_EDGE('',*,*,#38514,.T.); -#38516=ORIENTED_EDGE('',*,*,#29113,.T.); -#38517=ORIENTED_EDGE('',*,*,#38501,.F.); -#38518=EDGE_LOOP('',(#38513,#38515,#38516,#38517)); -#38519=FACE_OUTER_BOUND('',#38518,.F.); -#38521=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.71875E0)); -#38522=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38523=DIRECTION('',(0.E0,0.E0,1.E0)); -#38524=AXIS2_PLACEMENT_3D('',#38521,#38522,#38523); -#38525=PLANE('',#38524); -#38526=ORIENTED_EDGE('',*,*,#25598,.F.); -#38528=ORIENTED_EDGE('',*,*,#38527,.T.); -#38529=ORIENTED_EDGE('',*,*,#29115,.T.); -#38530=ORIENTED_EDGE('',*,*,#38514,.F.); -#38531=EDGE_LOOP('',(#38526,#38528,#38529,#38530)); -#38532=FACE_OUTER_BOUND('',#38531,.F.); -#38534=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.643750017881E0)); -#38535=DIRECTION('',(-9.620371902713E-1,0.E0,2.729183843844E-1)); -#38536=DIRECTION('',(2.729183843844E-1,0.E0,9.620371902713E-1)); -#38537=AXIS2_PLACEMENT_3D('',#38534,#38535,#38536); -#38538=PLANE('',#38537); -#38539=ORIENTED_EDGE('',*,*,#25596,.F.); -#38541=ORIENTED_EDGE('',*,*,#38540,.T.); -#38542=ORIENTED_EDGE('',*,*,#29117,.T.); -#38543=ORIENTED_EDGE('',*,*,#38527,.F.); -#38544=EDGE_LOOP('',(#38539,#38541,#38542,#38543)); -#38545=FACE_OUTER_BOUND('',#38544,.F.); -#38547=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,9.587500017881E0)); -#38548=DIRECTION('',(-7.975043849273E-1,0.E0,6.033131492200E-1)); -#38549=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#38550=AXIS2_PLACEMENT_3D('',#38547,#38548,#38549); -#38551=PLANE('',#38550); -#38552=ORIENTED_EDGE('',*,*,#25594,.F.); -#38554=ORIENTED_EDGE('',*,*,#38553,.T.); -#38555=ORIENTED_EDGE('',*,*,#29119,.T.); -#38556=ORIENTED_EDGE('',*,*,#38540,.F.); -#38557=EDGE_LOOP('',(#38552,#38554,#38555,#38556)); -#38558=FACE_OUTER_BOUND('',#38557,.F.); -#38560=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,9.568749982119E0)); -#38561=DIRECTION('',(-2.818421752748E-1,0.E0,9.594607799365E-1)); -#38562=DIRECTION('',(9.594607799365E-1,0.E0,2.818421752748E-1)); -#38563=AXIS2_PLACEMENT_3D('',#38560,#38561,#38562); -#38564=PLANE('',#38563); -#38565=ORIENTED_EDGE('',*,*,#25592,.F.); -#38566=ORIENTED_EDGE('',*,*,#38061,.T.); -#38567=ORIENTED_EDGE('',*,*,#29121,.T.); -#38568=ORIENTED_EDGE('',*,*,#38553,.F.); -#38569=EDGE_LOOP('',(#38565,#38566,#38567,#38568)); -#38570=FACE_OUTER_BOUND('',#38569,.F.); -#38572=CARTESIAN_POINT('',(5.75E0,1.55E0,9.193749964237E0)); -#38573=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38574=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38575=AXIS2_PLACEMENT_3D('',#38572,#38573,#38574); -#38576=PLANE('',#38575); -#38577=ORIENTED_EDGE('',*,*,#25672,.F.); -#38579=ORIENTED_EDGE('',*,*,#38578,.T.); -#38580=ORIENTED_EDGE('',*,*,#29138,.T.); -#38582=ORIENTED_EDGE('',*,*,#38581,.F.); -#38583=EDGE_LOOP('',(#38577,#38579,#38580,#38582)); -#38584=FACE_OUTER_BOUND('',#38583,.F.); -#38586=CARTESIAN_POINT('',(5.75E0,1.55E0,9.306249964237E0)); -#38587=DIRECTION('',(1.E0,0.E0,0.E0)); -#38588=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38589=AXIS2_PLACEMENT_3D('',#38586,#38587,#38588); -#38590=PLANE('',#38589); -#38591=ORIENTED_EDGE('',*,*,#25678,.F.); -#38593=ORIENTED_EDGE('',*,*,#38592,.T.); -#38594=ORIENTED_EDGE('',*,*,#29140,.T.); -#38595=ORIENTED_EDGE('',*,*,#38578,.F.); -#38596=EDGE_LOOP('',(#38591,#38593,#38594,#38595)); -#38597=FACE_OUTER_BOUND('',#38596,.F.); -#38599=CARTESIAN_POINT('',(4.75E0,1.55E0,9.306249964237E0)); -#38600=DIRECTION('',(0.E0,0.E0,1.E0)); -#38601=DIRECTION('',(1.E0,0.E0,0.E0)); -#38602=AXIS2_PLACEMENT_3D('',#38599,#38600,#38601); -#38603=PLANE('',#38602); -#38604=ORIENTED_EDGE('',*,*,#25676,.F.); -#38606=ORIENTED_EDGE('',*,*,#38605,.T.); -#38607=ORIENTED_EDGE('',*,*,#29142,.T.); -#38608=ORIENTED_EDGE('',*,*,#38592,.F.); -#38609=EDGE_LOOP('',(#38604,#38606,#38607,#38608)); -#38610=FACE_OUTER_BOUND('',#38609,.F.); -#38612=CARTESIAN_POINT('',(4.75E0,1.55E0,9.193749964237E0)); -#38613=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38614=DIRECTION('',(0.E0,0.E0,1.E0)); -#38615=AXIS2_PLACEMENT_3D('',#38612,#38613,#38614); -#38616=PLANE('',#38615); -#38617=ORIENTED_EDGE('',*,*,#25674,.F.); -#38618=ORIENTED_EDGE('',*,*,#38581,.T.); -#38619=ORIENTED_EDGE('',*,*,#29144,.T.); -#38620=ORIENTED_EDGE('',*,*,#38605,.F.); -#38621=EDGE_LOOP('',(#38617,#38618,#38619,#38620)); -#38622=FACE_OUTER_BOUND('',#38621,.F.); -#38624=CARTESIAN_POINT('',(4.75E0,1.55E0,8.59375E0)); -#38625=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38626=DIRECTION('',(0.E0,0.E0,1.E0)); -#38627=AXIS2_PLACEMENT_3D('',#38624,#38625,#38626); -#38628=PLANE('',#38627); -#38629=ORIENTED_EDGE('',*,*,#25682,.F.); -#38631=ORIENTED_EDGE('',*,*,#38630,.T.); -#38632=ORIENTED_EDGE('',*,*,#29161,.T.); -#38634=ORIENTED_EDGE('',*,*,#38633,.F.); -#38635=EDGE_LOOP('',(#38629,#38631,#38632,#38634)); -#38636=FACE_OUTER_BOUND('',#38635,.F.); -#38638=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,8.499999928474E0)); -#38639=DIRECTION('',(-9.752007923587E-1,0.E0,-2.213219704028E-1)); -#38640=DIRECTION('',(-2.213219704028E-1,0.E0,9.752007923587E-1)); -#38641=AXIS2_PLACEMENT_3D('',#38638,#38639,#38640); -#38642=PLANE('',#38641); -#38643=ORIENTED_EDGE('',*,*,#25708,.F.); -#38645=ORIENTED_EDGE('',*,*,#38644,.T.); -#38646=ORIENTED_EDGE('',*,*,#29163,.T.); -#38647=ORIENTED_EDGE('',*,*,#38630,.F.); -#38648=EDGE_LOOP('',(#38643,#38645,#38646,#38647)); -#38649=FACE_OUTER_BOUND('',#38648,.F.); -#38651=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,8.425E0)); -#38652=DIRECTION('',(-8.697572974984E-1,0.E0,-4.934797295212E-1)); -#38653=DIRECTION('',(-4.934797295212E-1,0.E0,8.697572974984E-1)); -#38654=AXIS2_PLACEMENT_3D('',#38651,#38652,#38653); -#38655=PLANE('',#38654); -#38656=ORIENTED_EDGE('',*,*,#25706,.F.); -#38658=ORIENTED_EDGE('',*,*,#38657,.T.); -#38659=ORIENTED_EDGE('',*,*,#29165,.T.); -#38660=ORIENTED_EDGE('',*,*,#38644,.F.); -#38661=EDGE_LOOP('',(#38656,#38658,#38659,#38660)); -#38662=FACE_OUTER_BOUND('',#38661,.F.); -#38664=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.350000071526E0)); -#38665=DIRECTION('',(-6.611559431073E-1,0.E0,-7.502485047595E-1)); -#38666=DIRECTION('',(-7.502485047595E-1,0.E0,6.611559431073E-1)); -#38667=AXIS2_PLACEMENT_3D('',#38664,#38665,#38666); -#38668=PLANE('',#38667); -#38669=ORIENTED_EDGE('',*,*,#25704,.F.); -#38671=ORIENTED_EDGE('',*,*,#38670,.T.); -#38672=ORIENTED_EDGE('',*,*,#29167,.T.); -#38673=ORIENTED_EDGE('',*,*,#38657,.F.); -#38674=EDGE_LOOP('',(#38669,#38671,#38672,#38673)); -#38675=FACE_OUTER_BOUND('',#38674,.F.); -#38677=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,8.3125E0)); -#38678=DIRECTION('',(-4.032184156573E-1,0.E0,-9.151037696758E-1)); -#38679=DIRECTION('',(-9.151037696758E-1,0.E0,4.032184156573E-1)); -#38680=AXIS2_PLACEMENT_3D('',#38677,#38678,#38679); -#38681=PLANE('',#38680); -#38682=ORIENTED_EDGE('',*,*,#25702,.F.); -#38684=ORIENTED_EDGE('',*,*,#38683,.T.); -#38685=ORIENTED_EDGE('',*,*,#29169,.T.); -#38686=ORIENTED_EDGE('',*,*,#38670,.F.); -#38687=EDGE_LOOP('',(#38682,#38684,#38685,#38686)); -#38688=FACE_OUTER_BOUND('',#38687,.F.); -#38690=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.293750071526E0)); -#38691=DIRECTION('',(-1.735739345657E-1,0.E0,-9.848208411886E-1)); -#38692=DIRECTION('',(-9.848208411886E-1,0.E0,1.735739345657E-1)); -#38693=AXIS2_PLACEMENT_3D('',#38690,#38691,#38692); -#38694=PLANE('',#38693); -#38695=ORIENTED_EDGE('',*,*,#25700,.F.); -#38697=ORIENTED_EDGE('',*,*,#38696,.T.); -#38698=ORIENTED_EDGE('',*,*,#29171,.T.); -#38699=ORIENTED_EDGE('',*,*,#38683,.F.); -#38700=EDGE_LOOP('',(#38695,#38697,#38698,#38699)); -#38701=FACE_OUTER_BOUND('',#38700,.F.); -#38703=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.293750071526E0)); -#38704=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38705=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38706=AXIS2_PLACEMENT_3D('',#38703,#38704,#38705); -#38707=PLANE('',#38706); -#38708=ORIENTED_EDGE('',*,*,#25698,.F.); -#38710=ORIENTED_EDGE('',*,*,#38709,.T.); -#38711=ORIENTED_EDGE('',*,*,#29173,.T.); -#38712=ORIENTED_EDGE('',*,*,#38696,.F.); -#38713=EDGE_LOOP('',(#38708,#38710,#38711,#38712)); -#38714=FACE_OUTER_BOUND('',#38713,.F.); -#38716=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,8.3125E0)); -#38717=DIRECTION('',(1.735740288863E-1,0.E0,-9.848208245646E-1)); -#38718=DIRECTION('',(-9.848208245646E-1,0.E0,-1.735740288863E-1)); -#38719=AXIS2_PLACEMENT_3D('',#38716,#38717,#38718); -#38720=PLANE('',#38719); -#38721=ORIENTED_EDGE('',*,*,#25696,.F.); -#38723=ORIENTED_EDGE('',*,*,#38722,.T.); -#38724=ORIENTED_EDGE('',*,*,#29175,.T.); -#38725=ORIENTED_EDGE('',*,*,#38709,.F.); -#38726=EDGE_LOOP('',(#38721,#38723,#38724,#38725)); -#38727=FACE_OUTER_BOUND('',#38726,.F.); -#38729=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.350000071526E0)); -#38730=DIRECTION('',(4.032183565367E-1,0.E0,-9.151037957259E-1)); -#38731=DIRECTION('',(-9.151037957259E-1,0.E0,-4.032183565367E-1)); -#38732=AXIS2_PLACEMENT_3D('',#38729,#38730,#38731); -#38733=PLANE('',#38732); -#38734=ORIENTED_EDGE('',*,*,#25694,.F.); -#38736=ORIENTED_EDGE('',*,*,#38735,.T.); -#38737=ORIENTED_EDGE('',*,*,#29177,.T.); -#38738=ORIENTED_EDGE('',*,*,#38722,.F.); -#38739=EDGE_LOOP('',(#38734,#38736,#38737,#38738)); -#38740=FACE_OUTER_BOUND('',#38739,.F.); -#38742=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,8.425E0)); -#38743=DIRECTION('',(6.611559105280E-1,0.E0,-7.502485334700E-1)); -#38744=DIRECTION('',(-7.502485334700E-1,0.E0,-6.611559105280E-1)); -#38745=AXIS2_PLACEMENT_3D('',#38742,#38743,#38744); -#38746=PLANE('',#38745); -#38747=ORIENTED_EDGE('',*,*,#25692,.F.); -#38749=ORIENTED_EDGE('',*,*,#38748,.T.); -#38750=ORIENTED_EDGE('',*,*,#29179,.T.); -#38751=ORIENTED_EDGE('',*,*,#38735,.F.); -#38752=EDGE_LOOP('',(#38747,#38749,#38750,#38751)); -#38753=FACE_OUTER_BOUND('',#38752,.F.); -#38755=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,8.499999928474E0)); -#38756=DIRECTION('',(8.697572696849E-1,0.E0,-4.934797785425E-1)); -#38757=DIRECTION('',(-4.934797785425E-1,0.E0,-8.697572696849E-1)); -#38758=AXIS2_PLACEMENT_3D('',#38755,#38756,#38757); -#38759=PLANE('',#38758); -#38760=ORIENTED_EDGE('',*,*,#25690,.F.); -#38762=ORIENTED_EDGE('',*,*,#38761,.T.); -#38763=ORIENTED_EDGE('',*,*,#29181,.T.); -#38764=ORIENTED_EDGE('',*,*,#38748,.F.); -#38765=EDGE_LOOP('',(#38760,#38762,#38763,#38764)); -#38766=FACE_OUTER_BOUND('',#38765,.F.); -#38768=CARTESIAN_POINT('',(5.75E0,1.55E0,8.59375E0)); -#38769=DIRECTION('',(9.752007881768E-1,0.E0,-2.213219888292E-1)); -#38770=DIRECTION('',(-2.213219888292E-1,0.E0,-9.752007881768E-1)); -#38771=AXIS2_PLACEMENT_3D('',#38768,#38769,#38770); -#38772=PLANE('',#38771); -#38773=ORIENTED_EDGE('',*,*,#25688,.F.); -#38775=ORIENTED_EDGE('',*,*,#38774,.T.); -#38776=ORIENTED_EDGE('',*,*,#29183,.T.); -#38777=ORIENTED_EDGE('',*,*,#38761,.F.); -#38778=EDGE_LOOP('',(#38773,#38775,#38776,#38777)); -#38779=FACE_OUTER_BOUND('',#38778,.F.); -#38781=CARTESIAN_POINT('',(5.75E0,1.55E0,9.04375E0)); -#38782=DIRECTION('',(1.E0,0.E0,0.E0)); -#38783=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38784=AXIS2_PLACEMENT_3D('',#38781,#38782,#38783); -#38785=PLANE('',#38784); -#38786=ORIENTED_EDGE('',*,*,#25686,.F.); -#38788=ORIENTED_EDGE('',*,*,#38787,.T.); -#38789=ORIENTED_EDGE('',*,*,#29185,.T.); -#38790=ORIENTED_EDGE('',*,*,#38774,.F.); -#38791=EDGE_LOOP('',(#38786,#38788,#38789,#38790)); -#38792=FACE_OUTER_BOUND('',#38791,.F.); -#38794=CARTESIAN_POINT('',(4.75E0,1.55E0,9.04375E0)); -#38795=DIRECTION('',(0.E0,0.E0,1.E0)); -#38796=DIRECTION('',(1.E0,0.E0,0.E0)); -#38797=AXIS2_PLACEMENT_3D('',#38794,#38795,#38796); -#38798=PLANE('',#38797); -#38799=ORIENTED_EDGE('',*,*,#25684,.F.); -#38800=ORIENTED_EDGE('',*,*,#38633,.T.); -#38801=ORIENTED_EDGE('',*,*,#29187,.T.); -#38802=ORIENTED_EDGE('',*,*,#38787,.F.); -#38803=EDGE_LOOP('',(#38799,#38800,#38801,#38802)); -#38804=FACE_OUTER_BOUND('',#38803,.F.); -#38806=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.93125E0)); -#38807=DIRECTION('',(1.E0,0.E0,0.E0)); -#38808=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38809=AXIS2_PLACEMENT_3D('',#38806,#38807,#38808); -#38810=PLANE('',#38809); -#38811=ORIENTED_EDGE('',*,*,#26718,.F.); -#38813=ORIENTED_EDGE('',*,*,#38812,.T.); -#38814=ORIENTED_EDGE('',*,*,#29191,.T.); -#38816=ORIENTED_EDGE('',*,*,#38815,.F.); -#38817=EDGE_LOOP('',(#38811,#38813,#38814,#38816)); -#38818=FACE_OUTER_BOUND('',#38817,.F.); -#38820=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.93125E0)); -#38821=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38822=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38823=AXIS2_PLACEMENT_3D('',#38820,#38821,#38822); -#38824=PLANE('',#38823); -#38825=ORIENTED_EDGE('',*,*,#26740,.F.); -#38827=ORIENTED_EDGE('',*,*,#38826,.T.); -#38828=ORIENTED_EDGE('',*,*,#29193,.T.); -#38829=ORIENTED_EDGE('',*,*,#38812,.F.); -#38830=EDGE_LOOP('',(#38825,#38827,#38828,#38829)); -#38831=FACE_OUTER_BOUND('',#38830,.F.); -#38833=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,8.59375E0)); -#38834=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38835=DIRECTION('',(0.E0,0.E0,1.E0)); -#38836=AXIS2_PLACEMENT_3D('',#38833,#38834,#38835); -#38837=PLANE('',#38836); -#38838=ORIENTED_EDGE('',*,*,#26738,.F.); -#38840=ORIENTED_EDGE('',*,*,#38839,.T.); -#38841=ORIENTED_EDGE('',*,*,#29195,.T.); -#38842=ORIENTED_EDGE('',*,*,#38826,.F.); -#38843=EDGE_LOOP('',(#38838,#38840,#38841,#38842)); -#38844=FACE_OUTER_BOUND('',#38843,.F.); -#38846=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,8.518750071526E0)); -#38847=DIRECTION('',(-9.620371390182E-1,0.E0,2.729185650512E-1)); -#38848=DIRECTION('',(2.729185650512E-1,0.E0,9.620371390182E-1)); -#38849=AXIS2_PLACEMENT_3D('',#38846,#38847,#38848); -#38850=PLANE('',#38849); -#38851=ORIENTED_EDGE('',*,*,#26736,.F.); -#38853=ORIENTED_EDGE('',*,*,#38852,.T.); -#38854=ORIENTED_EDGE('',*,*,#29197,.T.); -#38855=ORIENTED_EDGE('',*,*,#38839,.F.); -#38856=EDGE_LOOP('',(#38851,#38853,#38854,#38855)); -#38857=FACE_OUTER_BOUND('',#38856,.F.); -#38859=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,8.462500071526E0)); -#38860=DIRECTION('',(-7.975043849273E-1,0.E0,6.033131492200E-1)); -#38861=DIRECTION('',(6.033131492200E-1,0.E0,7.975043849273E-1)); -#38862=AXIS2_PLACEMENT_3D('',#38859,#38860,#38861); -#38863=PLANE('',#38862); -#38864=ORIENTED_EDGE('',*,*,#26734,.F.); -#38866=ORIENTED_EDGE('',*,*,#38865,.T.); -#38867=ORIENTED_EDGE('',*,*,#29199,.T.); -#38868=ORIENTED_EDGE('',*,*,#38852,.F.); -#38869=EDGE_LOOP('',(#38864,#38866,#38867,#38868)); -#38870=FACE_OUTER_BOUND('',#38869,.F.); -#38872=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,8.425E0)); -#38873=DIRECTION('',(-5.065498117766E-1,0.E0,8.622106982571E-1)); -#38874=DIRECTION('',(8.622106982571E-1,0.E0,5.065498117766E-1)); -#38875=AXIS2_PLACEMENT_3D('',#38872,#38873,#38874); -#38876=PLANE('',#38875); -#38877=ORIENTED_EDGE('',*,*,#26732,.F.); -#38879=ORIENTED_EDGE('',*,*,#38878,.T.); -#38880=ORIENTED_EDGE('',*,*,#29201,.T.); -#38881=ORIENTED_EDGE('',*,*,#38865,.F.); -#38882=EDGE_LOOP('',(#38877,#38879,#38880,#38881)); -#38883=FACE_OUTER_BOUND('',#38882,.F.); -#38885=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,8.406250071526E0)); -#38886=DIRECTION('',(-2.151521073348E-1,0.E0,9.765805500364E-1)); -#38887=DIRECTION('',(9.765805500364E-1,0.E0,2.151521073348E-1)); -#38888=AXIS2_PLACEMENT_3D('',#38885,#38886,#38887); -#38889=PLANE('',#38888); -#38890=ORIENTED_EDGE('',*,*,#26730,.F.); -#38892=ORIENTED_EDGE('',*,*,#38891,.T.); -#38893=ORIENTED_EDGE('',*,*,#29203,.T.); -#38894=ORIENTED_EDGE('',*,*,#38878,.F.); -#38895=EDGE_LOOP('',(#38890,#38892,#38893,#38894)); -#38896=FACE_OUTER_BOUND('',#38895,.F.); -#38898=CARTESIAN_POINT('',(5.090425550938E0,1.55E0,8.406250071526E0)); -#38899=DIRECTION('',(0.E0,0.E0,1.E0)); -#38900=DIRECTION('',(1.E0,0.E0,0.E0)); -#38901=AXIS2_PLACEMENT_3D('',#38898,#38899,#38900); -#38902=PLANE('',#38901); -#38903=ORIENTED_EDGE('',*,*,#26728,.F.); -#38905=ORIENTED_EDGE('',*,*,#38904,.T.); -#38906=ORIENTED_EDGE('',*,*,#29205,.T.); -#38907=ORIENTED_EDGE('',*,*,#38891,.F.); -#38908=EDGE_LOOP('',(#38903,#38905,#38906,#38907)); -#38909=FACE_OUTER_BOUND('',#38908,.F.); -#38911=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,8.425E0)); -#38912=DIRECTION('',(2.151521073348E-1,0.E0,9.765805500364E-1)); -#38913=DIRECTION('',(9.765805500364E-1,0.E0,-2.151521073348E-1)); -#38914=AXIS2_PLACEMENT_3D('',#38911,#38912,#38913); -#38915=PLANE('',#38914); -#38916=ORIENTED_EDGE('',*,*,#26726,.F.); -#38918=ORIENTED_EDGE('',*,*,#38917,.T.); -#38919=ORIENTED_EDGE('',*,*,#29207,.T.); -#38920=ORIENTED_EDGE('',*,*,#38904,.F.); -#38921=EDGE_LOOP('',(#38916,#38918,#38919,#38920)); -#38922=FACE_OUTER_BOUND('',#38921,.F.); -#38924=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,8.462500071526E0)); -#38925=DIRECTION('',(5.065494601308E-1,0.E0,8.622109048494E-1)); -#38926=DIRECTION('',(8.622109048494E-1,0.E0,-5.065494601308E-1)); -#38927=AXIS2_PLACEMENT_3D('',#38924,#38925,#38926); -#38928=PLANE('',#38927); -#38929=ORIENTED_EDGE('',*,*,#26724,.F.); -#38931=ORIENTED_EDGE('',*,*,#38930,.T.); -#38932=ORIENTED_EDGE('',*,*,#29209,.T.); -#38933=ORIENTED_EDGE('',*,*,#38917,.F.); -#38934=EDGE_LOOP('',(#38929,#38931,#38932,#38933)); -#38935=FACE_OUTER_BOUND('',#38934,.F.); -#38937=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,8.518750071526E0)); -#38938=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#38939=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#38940=AXIS2_PLACEMENT_3D('',#38937,#38938,#38939); -#38941=PLANE('',#38940); -#38942=ORIENTED_EDGE('',*,*,#26722,.F.); -#38944=ORIENTED_EDGE('',*,*,#38943,.T.); -#38945=ORIENTED_EDGE('',*,*,#29211,.T.); -#38946=ORIENTED_EDGE('',*,*,#38930,.F.); -#38947=EDGE_LOOP('',(#38942,#38944,#38945,#38946)); -#38948=FACE_OUTER_BOUND('',#38947,.F.); -#38950=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,8.59375E0)); -#38951=DIRECTION('',(9.620371390182E-1,0.E0,2.729185650512E-1)); -#38952=DIRECTION('',(2.729185650512E-1,0.E0,-9.620371390182E-1)); -#38953=AXIS2_PLACEMENT_3D('',#38950,#38951,#38952); -#38954=PLANE('',#38953); -#38955=ORIENTED_EDGE('',*,*,#26720,.F.); -#38956=ORIENTED_EDGE('',*,*,#38815,.T.); -#38957=ORIENTED_EDGE('',*,*,#29213,.T.); -#38958=ORIENTED_EDGE('',*,*,#38943,.F.); -#38959=EDGE_LOOP('',(#38955,#38956,#38957,#38958)); -#38960=FACE_OUTER_BOUND('',#38959,.F.); -#38962=CARTESIAN_POINT('',(5.75E0,1.55E0,8.049999928474E0)); -#38963=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38964=DIRECTION('',(-1.E0,0.E0,0.E0)); -#38965=AXIS2_PLACEMENT_3D('',#38962,#38963,#38964); -#38966=PLANE('',#38965); -#38967=ORIENTED_EDGE('',*,*,#25712,.F.); -#38969=ORIENTED_EDGE('',*,*,#38968,.T.); -#38970=ORIENTED_EDGE('',*,*,#29230,.T.); -#38972=ORIENTED_EDGE('',*,*,#38971,.F.); -#38973=EDGE_LOOP('',(#38967,#38969,#38970,#38972)); -#38974=FACE_OUTER_BOUND('',#38973,.F.); -#38976=CARTESIAN_POINT('',(5.75E0,1.55E0,8.14375E0)); -#38977=DIRECTION('',(1.E0,0.E0,0.E0)); -#38978=DIRECTION('',(0.E0,0.E0,-1.E0)); -#38979=AXIS2_PLACEMENT_3D('',#38976,#38977,#38978); -#38980=PLANE('',#38979); -#38981=ORIENTED_EDGE('',*,*,#25718,.F.); -#38983=ORIENTED_EDGE('',*,*,#38982,.T.); -#38984=ORIENTED_EDGE('',*,*,#29232,.T.); -#38985=ORIENTED_EDGE('',*,*,#38968,.F.); -#38986=EDGE_LOOP('',(#38981,#38983,#38984,#38985)); -#38987=FACE_OUTER_BOUND('',#38986,.F.); -#38989=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.14375E0)); -#38990=DIRECTION('',(0.E0,0.E0,1.E0)); -#38991=DIRECTION('',(1.E0,0.E0,0.E0)); -#38992=AXIS2_PLACEMENT_3D('',#38989,#38990,#38991); -#38993=PLANE('',#38992); -#38994=ORIENTED_EDGE('',*,*,#25716,.F.); -#38996=ORIENTED_EDGE('',*,*,#38995,.T.); -#38997=ORIENTED_EDGE('',*,*,#29234,.T.); -#38998=ORIENTED_EDGE('',*,*,#38982,.F.); -#38999=EDGE_LOOP('',(#38994,#38996,#38997,#38998)); -#39000=FACE_OUTER_BOUND('',#38999,.F.); -#39002=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.049999928474E0)); -#39003=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39004=DIRECTION('',(0.E0,0.E0,1.E0)); -#39005=AXIS2_PLACEMENT_3D('',#39002,#39003,#39004); -#39006=PLANE('',#39005); -#39007=ORIENTED_EDGE('',*,*,#25714,.F.); -#39008=ORIENTED_EDGE('',*,*,#38971,.T.); -#39009=ORIENTED_EDGE('',*,*,#29236,.T.); -#39010=ORIENTED_EDGE('',*,*,#38995,.F.); -#39011=EDGE_LOOP('',(#39007,#39008,#39009,#39010)); -#39012=FACE_OUTER_BOUND('',#39011,.F.); -#39014=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.049999928474E0)); -#39015=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39016=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39017=AXIS2_PLACEMENT_3D('',#39014,#39015,#39016); -#39018=PLANE('',#39017); -#39019=ORIENTED_EDGE('',*,*,#25722,.F.); -#39021=ORIENTED_EDGE('',*,*,#39020,.T.); -#39022=ORIENTED_EDGE('',*,*,#29253,.T.); -#39024=ORIENTED_EDGE('',*,*,#39023,.F.); -#39025=EDGE_LOOP('',(#39019,#39021,#39022,#39024)); -#39026=FACE_OUTER_BOUND('',#39025,.F.); -#39028=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,8.14375E0)); -#39029=DIRECTION('',(1.E0,0.E0,0.E0)); -#39030=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39031=AXIS2_PLACEMENT_3D('',#39028,#39029,#39030); -#39032=PLANE('',#39031); -#39033=ORIENTED_EDGE('',*,*,#25728,.F.); -#39035=ORIENTED_EDGE('',*,*,#39034,.T.); -#39036=ORIENTED_EDGE('',*,*,#29255,.T.); -#39037=ORIENTED_EDGE('',*,*,#39020,.F.); -#39038=EDGE_LOOP('',(#39033,#39035,#39036,#39037)); -#39039=FACE_OUTER_BOUND('',#39038,.F.); -#39041=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.14375E0)); -#39042=DIRECTION('',(0.E0,0.E0,1.E0)); -#39043=DIRECTION('',(1.E0,0.E0,0.E0)); -#39044=AXIS2_PLACEMENT_3D('',#39041,#39042,#39043); -#39045=PLANE('',#39044); -#39046=ORIENTED_EDGE('',*,*,#25726,.F.); -#39048=ORIENTED_EDGE('',*,*,#39047,.T.); -#39049=ORIENTED_EDGE('',*,*,#29257,.T.); -#39050=ORIENTED_EDGE('',*,*,#39034,.F.); -#39051=EDGE_LOOP('',(#39046,#39048,#39049,#39050)); -#39052=FACE_OUTER_BOUND('',#39051,.F.); -#39054=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,8.049999928474E0)); -#39055=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39056=DIRECTION('',(0.E0,0.E0,1.E0)); -#39057=AXIS2_PLACEMENT_3D('',#39054,#39055,#39056); -#39058=PLANE('',#39057); -#39059=ORIENTED_EDGE('',*,*,#25724,.F.); -#39060=ORIENTED_EDGE('',*,*,#39023,.T.); -#39061=ORIENTED_EDGE('',*,*,#29259,.T.); -#39062=ORIENTED_EDGE('',*,*,#39047,.F.); -#39063=EDGE_LOOP('',(#39059,#39060,#39061,#39062)); -#39064=FACE_OUTER_BOUND('',#39063,.F.); -#39066=CARTESIAN_POINT('',(4.75E0,1.55E0,7.450000071526E0)); -#39067=DIRECTION('',(-6.166619811700E-1,0.E0,7.872280489029E-1)); -#39068=DIRECTION('',(7.872280489029E-1,0.E0,6.166619811700E-1)); -#39069=AXIS2_PLACEMENT_3D('',#39066,#39067,#39068); -#39070=PLANE('',#39069); -#39071=ORIENTED_EDGE('',*,*,#25732,.F.); -#39073=ORIENTED_EDGE('',*,*,#39072,.T.); -#39074=ORIENTED_EDGE('',*,*,#29276,.T.); -#39076=ORIENTED_EDGE('',*,*,#39075,.F.); -#39077=EDGE_LOOP('',(#39071,#39073,#39074,#39076)); -#39078=FACE_OUTER_BOUND('',#39077,.F.); -#39080=CARTESIAN_POINT('',(4.75E0,1.55E0,7.337500071526E0)); -#39081=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39082=DIRECTION('',(0.E0,0.E0,1.E0)); -#39083=AXIS2_PLACEMENT_3D('',#39080,#39081,#39082); -#39084=PLANE('',#39083); -#39085=ORIENTED_EDGE('',*,*,#25752,.F.); -#39087=ORIENTED_EDGE('',*,*,#39086,.T.); -#39088=ORIENTED_EDGE('',*,*,#29278,.T.); -#39089=ORIENTED_EDGE('',*,*,#39072,.F.); -#39090=EDGE_LOOP('',(#39085,#39087,#39088,#39089)); -#39091=FACE_OUTER_BOUND('',#39090,.F.); -#39093=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.337500071526E0)); -#39094=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39095=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39096=AXIS2_PLACEMENT_3D('',#39093,#39094,#39095); -#39097=PLANE('',#39096); -#39098=ORIENTED_EDGE('',*,*,#25750,.F.); -#39100=ORIENTED_EDGE('',*,*,#39099,.T.); -#39101=ORIENTED_EDGE('',*,*,#29280,.T.); -#39102=ORIENTED_EDGE('',*,*,#39086,.F.); -#39103=EDGE_LOOP('',(#39098,#39100,#39101,#39102)); -#39104=FACE_OUTER_BOUND('',#39103,.F.); -#39106=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.149999928474E0)); -#39107=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39108=DIRECTION('',(0.E0,0.E0,1.E0)); -#39109=AXIS2_PLACEMENT_3D('',#39106,#39107,#39108); -#39110=PLANE('',#39109); -#39111=ORIENTED_EDGE('',*,*,#25748,.F.); -#39113=ORIENTED_EDGE('',*,*,#39112,.T.); -#39114=ORIENTED_EDGE('',*,*,#29282,.T.); -#39115=ORIENTED_EDGE('',*,*,#39099,.F.); -#39116=EDGE_LOOP('',(#39111,#39113,#39114,#39115)); -#39117=FACE_OUTER_BOUND('',#39116,.F.); -#39119=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.149999928474E0)); -#39120=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39121=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39122=AXIS2_PLACEMENT_3D('',#39119,#39120,#39121); -#39123=PLANE('',#39122); -#39124=ORIENTED_EDGE('',*,*,#25746,.F.); -#39126=ORIENTED_EDGE('',*,*,#39125,.T.); -#39127=ORIENTED_EDGE('',*,*,#29284,.T.); -#39128=ORIENTED_EDGE('',*,*,#39112,.F.); -#39129=EDGE_LOOP('',(#39124,#39126,#39127,#39128)); -#39130=FACE_OUTER_BOUND('',#39129,.F.); -#39132=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.337500071526E0)); -#39133=DIRECTION('',(1.E0,0.E0,0.E0)); -#39134=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39135=AXIS2_PLACEMENT_3D('',#39132,#39133,#39134); -#39136=PLANE('',#39135); -#39137=ORIENTED_EDGE('',*,*,#25744,.F.); -#39139=ORIENTED_EDGE('',*,*,#39138,.T.); -#39140=ORIENTED_EDGE('',*,*,#29286,.T.); -#39141=ORIENTED_EDGE('',*,*,#39125,.F.); -#39142=EDGE_LOOP('',(#39137,#39139,#39140,#39141)); -#39143=FACE_OUTER_BOUND('',#39142,.F.); -#39145=CARTESIAN_POINT('',(5.75E0,1.55E0,7.337500071526E0)); -#39146=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39147=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39148=AXIS2_PLACEMENT_3D('',#39145,#39146,#39147); -#39149=PLANE('',#39148); -#39150=ORIENTED_EDGE('',*,*,#25742,.F.); -#39152=ORIENTED_EDGE('',*,*,#39151,.T.); -#39153=ORIENTED_EDGE('',*,*,#29288,.T.); -#39154=ORIENTED_EDGE('',*,*,#39138,.F.); -#39155=EDGE_LOOP('',(#39150,#39152,#39153,#39154)); -#39156=FACE_OUTER_BOUND('',#39155,.F.); -#39158=CARTESIAN_POINT('',(5.75E0,1.55E0,7.450000071526E0)); -#39159=DIRECTION('',(1.E0,0.E0,0.E0)); -#39160=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39161=AXIS2_PLACEMENT_3D('',#39158,#39159,#39160); -#39162=PLANE('',#39161); -#39163=ORIENTED_EDGE('',*,*,#25740,.F.); -#39165=ORIENTED_EDGE('',*,*,#39164,.T.); -#39166=ORIENTED_EDGE('',*,*,#29290,.T.); -#39167=ORIENTED_EDGE('',*,*,#39151,.F.); -#39168=EDGE_LOOP('',(#39163,#39165,#39166,#39167)); -#39169=FACE_OUTER_BOUND('',#39168,.F.); -#39171=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.450000071526E0)); -#39172=DIRECTION('',(0.E0,0.E0,1.E0)); -#39173=DIRECTION('',(1.E0,0.E0,0.E0)); -#39174=AXIS2_PLACEMENT_3D('',#39171,#39172,#39173); -#39175=PLANE('',#39174); -#39176=ORIENTED_EDGE('',*,*,#25738,.F.); -#39178=ORIENTED_EDGE('',*,*,#39177,.T.); -#39179=ORIENTED_EDGE('',*,*,#29292,.T.); -#39180=ORIENTED_EDGE('',*,*,#39164,.F.); -#39181=EDGE_LOOP('',(#39176,#39178,#39179,#39180)); -#39182=FACE_OUTER_BOUND('',#39181,.F.); -#39184=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,7.900000071526E0)); -#39185=DIRECTION('',(1.E0,0.E0,0.E0)); -#39186=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39187=AXIS2_PLACEMENT_3D('',#39184,#39185,#39186); -#39188=PLANE('',#39187); -#39189=ORIENTED_EDGE('',*,*,#25736,.F.); -#39191=ORIENTED_EDGE('',*,*,#39190,.T.); -#39192=ORIENTED_EDGE('',*,*,#29294,.T.); -#39193=ORIENTED_EDGE('',*,*,#39177,.F.); -#39194=EDGE_LOOP('',(#39189,#39191,#39192,#39193)); -#39195=FACE_OUTER_BOUND('',#39194,.F.); -#39197=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.900000071526E0)); -#39198=DIRECTION('',(0.E0,0.E0,1.E0)); -#39199=DIRECTION('',(1.E0,0.E0,0.E0)); -#39200=AXIS2_PLACEMENT_3D('',#39197,#39198,#39199); -#39201=PLANE('',#39200); -#39202=ORIENTED_EDGE('',*,*,#25734,.F.); -#39203=ORIENTED_EDGE('',*,*,#39075,.T.); -#39204=ORIENTED_EDGE('',*,*,#29296,.T.); -#39205=ORIENTED_EDGE('',*,*,#39190,.F.); -#39206=EDGE_LOOP('',(#39202,#39203,#39204,#39205)); -#39207=FACE_OUTER_BOUND('',#39206,.F.); -#39209=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.768749928474E0)); -#39210=DIRECTION('',(6.191666049797E-1,0.E0,-7.852596483189E-1)); -#39211=DIRECTION('',(-7.852596483189E-1,0.E0,-6.191666049797E-1)); -#39212=AXIS2_PLACEMENT_3D('',#39209,#39210,#39211); -#39213=PLANE('',#39212); -#39214=ORIENTED_EDGE('',*,*,#26750,.F.); -#39216=ORIENTED_EDGE('',*,*,#39215,.T.); -#39217=ORIENTED_EDGE('',*,*,#29300,.T.); -#39219=ORIENTED_EDGE('',*,*,#39218,.F.); -#39220=EDGE_LOOP('',(#39214,#39216,#39217,#39219)); -#39221=FACE_OUTER_BOUND('',#39220,.F.); -#39223=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,7.450000071526E0)); -#39224=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39225=DIRECTION('',(0.E0,0.E0,1.E0)); -#39226=AXIS2_PLACEMENT_3D('',#39223,#39224,#39225); -#39227=PLANE('',#39226); -#39228=ORIENTED_EDGE('',*,*,#26754,.F.); -#39230=ORIENTED_EDGE('',*,*,#39229,.T.); -#39231=ORIENTED_EDGE('',*,*,#29302,.T.); -#39232=ORIENTED_EDGE('',*,*,#39215,.F.); -#39233=EDGE_LOOP('',(#39228,#39230,#39231,#39232)); -#39234=FACE_OUTER_BOUND('',#39233,.F.); -#39236=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,7.450000071526E0)); -#39237=DIRECTION('',(0.E0,0.E0,1.E0)); -#39238=DIRECTION('',(1.E0,0.E0,0.E0)); -#39239=AXIS2_PLACEMENT_3D('',#39236,#39237,#39238); -#39240=PLANE('',#39239); -#39241=ORIENTED_EDGE('',*,*,#26752,.F.); -#39242=ORIENTED_EDGE('',*,*,#39218,.T.); -#39243=ORIENTED_EDGE('',*,*,#29304,.T.); -#39244=ORIENTED_EDGE('',*,*,#39229,.F.); -#39245=EDGE_LOOP('',(#39241,#39242,#39243,#39244)); -#39246=FACE_OUTER_BOUND('',#39245,.F.); -#39248=CARTESIAN_POINT('',(5.75E0,1.55E0,6.774999856949E0)); -#39249=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39250=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39251=AXIS2_PLACEMENT_3D('',#39248,#39249,#39250); -#39252=PLANE('',#39251); -#39253=ORIENTED_EDGE('',*,*,#25756,.F.); -#39255=ORIENTED_EDGE('',*,*,#39254,.T.); -#39256=ORIENTED_EDGE('',*,*,#29321,.T.); -#39258=ORIENTED_EDGE('',*,*,#39257,.F.); -#39259=EDGE_LOOP('',(#39253,#39255,#39256,#39258)); -#39260=FACE_OUTER_BOUND('',#39259,.F.); -#39262=CARTESIAN_POINT('',(5.75E0,1.55E0,6.887500071526E0)); -#39263=DIRECTION('',(1.E0,0.E0,0.E0)); -#39264=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39265=AXIS2_PLACEMENT_3D('',#39262,#39263,#39264); -#39266=PLANE('',#39265); -#39267=ORIENTED_EDGE('',*,*,#25768,.F.); -#39269=ORIENTED_EDGE('',*,*,#39268,.T.); -#39270=ORIENTED_EDGE('',*,*,#29323,.T.); -#39271=ORIENTED_EDGE('',*,*,#39254,.F.); -#39272=EDGE_LOOP('',(#39267,#39269,#39270,#39271)); -#39273=FACE_OUTER_BOUND('',#39272,.F.); -#39275=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.887500071526E0)); -#39276=DIRECTION('',(0.E0,0.E0,1.E0)); -#39277=DIRECTION('',(1.E0,0.E0,0.E0)); -#39278=AXIS2_PLACEMENT_3D('',#39275,#39276,#39277); -#39279=PLANE('',#39278); -#39280=ORIENTED_EDGE('',*,*,#25766,.F.); -#39282=ORIENTED_EDGE('',*,*,#39281,.T.); -#39283=ORIENTED_EDGE('',*,*,#29325,.T.); -#39284=ORIENTED_EDGE('',*,*,#39268,.F.); -#39285=EDGE_LOOP('',(#39280,#39282,#39283,#39284)); -#39286=FACE_OUTER_BOUND('',#39285,.F.); -#39288=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,7.000000071526E0)); -#39289=DIRECTION('',(6.027321899048E-1,0.E0,-7.979435489134E-1)); -#39290=DIRECTION('',(-7.979435489134E-1,0.E0,-6.027321899048E-1)); -#39291=AXIS2_PLACEMENT_3D('',#39288,#39289,#39290); -#39292=PLANE('',#39291); -#39293=ORIENTED_EDGE('',*,*,#25764,.F.); -#39295=ORIENTED_EDGE('',*,*,#39294,.T.); -#39296=ORIENTED_EDGE('',*,*,#29327,.T.); -#39297=ORIENTED_EDGE('',*,*,#39281,.F.); -#39298=EDGE_LOOP('',(#39293,#39295,#39296,#39297)); -#39299=FACE_OUTER_BOUND('',#39298,.F.); -#39301=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,7.000000071526E0)); -#39302=DIRECTION('',(0.E0,0.E0,1.E0)); -#39303=DIRECTION('',(1.E0,0.E0,0.E0)); -#39304=AXIS2_PLACEMENT_3D('',#39301,#39302,#39303); -#39305=PLANE('',#39304); -#39306=ORIENTED_EDGE('',*,*,#25762,.F.); -#39308=ORIENTED_EDGE('',*,*,#39307,.T.); -#39309=ORIENTED_EDGE('',*,*,#29329,.T.); -#39310=ORIENTED_EDGE('',*,*,#39294,.F.); -#39311=EDGE_LOOP('',(#39306,#39308,#39309,#39310)); -#39312=FACE_OUTER_BOUND('',#39311,.F.); -#39314=CARTESIAN_POINT('',(4.75E0,1.55E0,6.887500071526E0)); -#39315=DIRECTION('',(-6.027323434897E-1,0.E0,7.979434329020E-1)); -#39316=DIRECTION('',(7.979434329020E-1,0.E0,6.027323434897E-1)); -#39317=AXIS2_PLACEMENT_3D('',#39314,#39315,#39316); -#39318=PLANE('',#39317); -#39319=ORIENTED_EDGE('',*,*,#25760,.F.); -#39321=ORIENTED_EDGE('',*,*,#39320,.T.); -#39322=ORIENTED_EDGE('',*,*,#29331,.T.); -#39323=ORIENTED_EDGE('',*,*,#39307,.F.); -#39324=EDGE_LOOP('',(#39319,#39321,#39322,#39323)); -#39325=FACE_OUTER_BOUND('',#39324,.F.); -#39327=CARTESIAN_POINT('',(4.75E0,1.55E0,6.774999856949E0)); -#39328=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39329=DIRECTION('',(0.E0,0.E0,1.E0)); -#39330=AXIS2_PLACEMENT_3D('',#39327,#39328,#39329); -#39331=PLANE('',#39330); -#39332=ORIENTED_EDGE('',*,*,#25758,.F.); -#39333=ORIENTED_EDGE('',*,*,#39257,.T.); -#39334=ORIENTED_EDGE('',*,*,#29333,.T.); -#39335=ORIENTED_EDGE('',*,*,#39320,.F.); -#39336=EDGE_LOOP('',(#39332,#39333,#39334,#39335)); -#39337=FACE_OUTER_BOUND('',#39336,.F.); -#39339=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.625E0)); -#39340=DIRECTION('',(0.E0,0.E0,1.E0)); -#39341=DIRECTION('',(1.E0,0.E0,0.E0)); -#39342=AXIS2_PLACEMENT_3D('',#39339,#39340,#39341); -#39343=PLANE('',#39342); -#39344=ORIENTED_EDGE('',*,*,#25772,.F.); -#39346=ORIENTED_EDGE('',*,*,#39345,.T.); -#39347=ORIENTED_EDGE('',*,*,#29350,.T.); -#39349=ORIENTED_EDGE('',*,*,#39348,.F.); -#39350=EDGE_LOOP('',(#39344,#39346,#39347,#39349)); -#39351=FACE_OUTER_BOUND('',#39350,.F.); -#39353=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.606249856949E0)); -#39354=DIRECTION('',(-1.735759554437E-1,0.E0,9.848204850082E-1)); -#39355=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554437E-1)); -#39356=AXIS2_PLACEMENT_3D('',#39353,#39354,#39355); -#39357=PLANE('',#39356); -#39358=ORIENTED_EDGE('',*,*,#25822,.F.); -#39360=ORIENTED_EDGE('',*,*,#39359,.T.); -#39361=ORIENTED_EDGE('',*,*,#29352,.T.); -#39362=ORIENTED_EDGE('',*,*,#39345,.F.); -#39363=EDGE_LOOP('',(#39358,#39360,#39361,#39362)); -#39364=FACE_OUTER_BOUND('',#39363,.F.); -#39366=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,6.587500143051E0)); -#39367=DIRECTION('',(-2.818374791740E-1,0.E0,9.594621594064E-1)); -#39368=DIRECTION('',(9.594621594064E-1,0.E0,2.818374791740E-1)); -#39369=AXIS2_PLACEMENT_3D('',#39366,#39367,#39368); -#39370=PLANE('',#39369); -#39371=ORIENTED_EDGE('',*,*,#25820,.F.); -#39373=ORIENTED_EDGE('',*,*,#39372,.T.); -#39374=ORIENTED_EDGE('',*,*,#29354,.T.); -#39375=ORIENTED_EDGE('',*,*,#39359,.F.); -#39376=EDGE_LOOP('',(#39371,#39373,#39374,#39375)); -#39377=FACE_OUTER_BOUND('',#39376,.F.); -#39379=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.549999856949E0)); -#39380=DIRECTION('',(-4.032203477633E-1,0.E0,9.151029183374E-1)); -#39381=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#39382=AXIS2_PLACEMENT_3D('',#39379,#39380,#39381); -#39383=PLANE('',#39382); -#39384=ORIENTED_EDGE('',*,*,#25818,.F.); -#39386=ORIENTED_EDGE('',*,*,#39385,.T.); -#39387=ORIENTED_EDGE('',*,*,#29356,.T.); -#39388=ORIENTED_EDGE('',*,*,#39372,.F.); -#39389=EDGE_LOOP('',(#39384,#39386,#39387,#39388)); -#39390=FACE_OUTER_BOUND('',#39389,.F.); -#39392=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.493749856949E0)); -#39393=DIRECTION('',(-6.611562980142E-1,0.E0,7.502481919980E-1)); -#39394=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#39395=AXIS2_PLACEMENT_3D('',#39392,#39393,#39394); -#39396=PLANE('',#39395); -#39397=ORIENTED_EDGE('',*,*,#25816,.F.); -#39399=ORIENTED_EDGE('',*,*,#39398,.T.); -#39400=ORIENTED_EDGE('',*,*,#29358,.T.); -#39401=ORIENTED_EDGE('',*,*,#39385,.F.); -#39402=EDGE_LOOP('',(#39397,#39399,#39400,#39401)); -#39403=FACE_OUTER_BOUND('',#39402,.F.); -#39405=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.4E0)); -#39406=DIRECTION('',(-8.265988793059E-1,0.E0,5.627915179978E-1)); -#39407=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#39408=AXIS2_PLACEMENT_3D('',#39405,#39406,#39407); -#39409=PLANE('',#39408); -#39410=ORIENTED_EDGE('',*,*,#25814,.F.); -#39412=ORIENTED_EDGE('',*,*,#39411,.T.); -#39413=ORIENTED_EDGE('',*,*,#29360,.T.); -#39414=ORIENTED_EDGE('',*,*,#39398,.F.); -#39415=EDGE_LOOP('',(#39410,#39412,#39413,#39414)); -#39416=FACE_OUTER_BOUND('',#39415,.F.); -#39418=CARTESIAN_POINT('',(4.75E0,1.55E0,6.2875E0)); -#39419=DIRECTION('',(-9.825817148807E-1,0.E0,1.858310350350E-1)); -#39420=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#39421=AXIS2_PLACEMENT_3D('',#39418,#39419,#39420); -#39422=PLANE('',#39421); -#39423=ORIENTED_EDGE('',*,*,#25812,.F.); -#39425=ORIENTED_EDGE('',*,*,#39424,.T.); -#39426=ORIENTED_EDGE('',*,*,#29362,.T.); -#39427=ORIENTED_EDGE('',*,*,#39411,.F.); -#39428=EDGE_LOOP('',(#39423,#39425,#39426,#39427)); -#39429=FACE_OUTER_BOUND('',#39428,.F.); -#39431=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.175E0)); -#39432=DIRECTION('',(-9.825817148807E-1,0.E0,-1.858310350350E-1)); -#39433=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#39434=AXIS2_PLACEMENT_3D('',#39431,#39432,#39433); -#39435=PLANE('',#39434); -#39436=ORIENTED_EDGE('',*,*,#25810,.F.); -#39438=ORIENTED_EDGE('',*,*,#39437,.T.); -#39439=ORIENTED_EDGE('',*,*,#29364,.T.); -#39440=ORIENTED_EDGE('',*,*,#39424,.F.); -#39441=EDGE_LOOP('',(#39436,#39438,#39439,#39440)); -#39442=FACE_OUTER_BOUND('',#39441,.F.); -#39444=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,6.081250143051E0)); -#39445=DIRECTION('',(-8.265988793059E-1,0.E0,-5.627915179978E-1)); -#39446=DIRECTION('',(-5.627915179978E-1,0.E0,8.265988793059E-1)); -#39447=AXIS2_PLACEMENT_3D('',#39444,#39445,#39446); -#39448=PLANE('',#39447); -#39449=ORIENTED_EDGE('',*,*,#25808,.F.); -#39451=ORIENTED_EDGE('',*,*,#39450,.T.); -#39452=ORIENTED_EDGE('',*,*,#29366,.T.); -#39453=ORIENTED_EDGE('',*,*,#39437,.F.); -#39454=EDGE_LOOP('',(#39449,#39451,#39452,#39453)); -#39455=FACE_OUTER_BOUND('',#39454,.F.); -#39457=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,6.025000143051E0)); -#39458=DIRECTION('',(-6.611562980142E-1,0.E0,-7.502481919980E-1)); -#39459=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#39460=AXIS2_PLACEMENT_3D('',#39457,#39458,#39459); -#39461=PLANE('',#39460); -#39462=ORIENTED_EDGE('',*,*,#25806,.F.); -#39464=ORIENTED_EDGE('',*,*,#39463,.T.); -#39465=ORIENTED_EDGE('',*,*,#29368,.T.); -#39466=ORIENTED_EDGE('',*,*,#39450,.F.); -#39467=EDGE_LOOP('',(#39462,#39464,#39465,#39466)); -#39468=FACE_OUTER_BOUND('',#39467,.F.); -#39470=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.987499856949E0)); -#39471=DIRECTION('',(-4.032203477633E-1,0.E0,-9.151029183374E-1)); -#39472=DIRECTION('',(-9.151029183374E-1,0.E0,4.032203477633E-1)); -#39473=AXIS2_PLACEMENT_3D('',#39470,#39471,#39472); -#39474=PLANE('',#39473); -#39475=ORIENTED_EDGE('',*,*,#25804,.F.); -#39477=ORIENTED_EDGE('',*,*,#39476,.T.); -#39478=ORIENTED_EDGE('',*,*,#29370,.T.); -#39479=ORIENTED_EDGE('',*,*,#39463,.F.); -#39480=EDGE_LOOP('',(#39475,#39477,#39478,#39479)); -#39481=FACE_OUTER_BOUND('',#39480,.F.); -#39483=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.968750143051E0)); -#39484=DIRECTION('',(-2.818374791740E-1,0.E0,-9.594621594064E-1)); -#39485=DIRECTION('',(-9.594621594064E-1,0.E0,2.818374791740E-1)); -#39486=AXIS2_PLACEMENT_3D('',#39483,#39484,#39485); -#39487=PLANE('',#39486); -#39488=ORIENTED_EDGE('',*,*,#25802,.F.); -#39490=ORIENTED_EDGE('',*,*,#39489,.T.); -#39491=ORIENTED_EDGE('',*,*,#29372,.T.); -#39492=ORIENTED_EDGE('',*,*,#39476,.F.); -#39493=EDGE_LOOP('',(#39488,#39490,#39491,#39492)); -#39494=FACE_OUTER_BOUND('',#39493,.F.); -#39496=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.95E0)); -#39497=DIRECTION('',(-1.735759554437E-1,0.E0,-9.848204850082E-1)); -#39498=DIRECTION('',(-9.848204850082E-1,0.E0,1.735759554437E-1)); -#39499=AXIS2_PLACEMENT_3D('',#39496,#39497,#39498); -#39500=PLANE('',#39499); -#39501=ORIENTED_EDGE('',*,*,#25800,.F.); -#39503=ORIENTED_EDGE('',*,*,#39502,.T.); -#39504=ORIENTED_EDGE('',*,*,#29374,.T.); -#39505=ORIENTED_EDGE('',*,*,#39489,.F.); -#39506=EDGE_LOOP('',(#39501,#39503,#39504,#39505)); -#39507=FACE_OUTER_BOUND('',#39506,.F.); -#39509=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.95E0)); -#39510=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39511=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39512=AXIS2_PLACEMENT_3D('',#39509,#39510,#39511); -#39513=PLANE('',#39512); -#39514=ORIENTED_EDGE('',*,*,#25798,.F.); -#39516=ORIENTED_EDGE('',*,*,#39515,.T.); -#39517=ORIENTED_EDGE('',*,*,#29376,.T.); -#39518=ORIENTED_EDGE('',*,*,#39502,.F.); -#39519=EDGE_LOOP('',(#39514,#39516,#39517,#39518)); -#39520=FACE_OUTER_BOUND('',#39519,.F.); -#39522=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.968750143051E0)); -#39523=DIRECTION('',(1.735759082829E-1,0.E0,-9.848204933204E-1)); -#39524=DIRECTION('',(-9.848204933204E-1,0.E0,-1.735759082829E-1)); -#39525=AXIS2_PLACEMENT_3D('',#39522,#39523,#39524); -#39526=PLANE('',#39525); -#39527=ORIENTED_EDGE('',*,*,#25796,.F.); -#39529=ORIENTED_EDGE('',*,*,#39528,.T.); -#39530=ORIENTED_EDGE('',*,*,#29378,.T.); -#39531=ORIENTED_EDGE('',*,*,#39515,.F.); -#39532=EDGE_LOOP('',(#39527,#39529,#39530,#39531)); -#39533=FACE_OUTER_BOUND('',#39532,.F.); -#39535=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.987499856949E0)); -#39536=DIRECTION('',(2.818377214504E-1,0.E0,-9.594620882388E-1)); -#39537=DIRECTION('',(-9.594620882388E-1,0.E0,-2.818377214504E-1)); -#39538=AXIS2_PLACEMENT_3D('',#39535,#39536,#39537); -#39539=PLANE('',#39538); -#39540=ORIENTED_EDGE('',*,*,#25794,.F.); -#39542=ORIENTED_EDGE('',*,*,#39541,.T.); -#39543=ORIENTED_EDGE('',*,*,#29380,.T.); -#39544=ORIENTED_EDGE('',*,*,#39528,.F.); -#39545=EDGE_LOOP('',(#39540,#39542,#39543,#39544)); -#39546=FACE_OUTER_BOUND('',#39545,.F.); -#39548=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.025000143051E0)); -#39549=DIRECTION('',(4.032202886425E-1,0.E0,-9.151029443877E-1)); -#39550=DIRECTION('',(-9.151029443877E-1,0.E0,-4.032202886425E-1)); -#39551=AXIS2_PLACEMENT_3D('',#39548,#39549,#39550); -#39552=PLANE('',#39551); -#39553=ORIENTED_EDGE('',*,*,#25792,.F.); -#39555=ORIENTED_EDGE('',*,*,#39554,.T.); -#39556=ORIENTED_EDGE('',*,*,#29382,.T.); -#39557=ORIENTED_EDGE('',*,*,#39541,.F.); -#39558=EDGE_LOOP('',(#39553,#39555,#39556,#39557)); -#39559=FACE_OUTER_BOUND('',#39558,.F.); -#39561=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.081250143051E0)); -#39562=DIRECTION('',(6.611562545751E-1,0.E0,-7.502482302787E-1)); -#39563=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#39564=AXIS2_PLACEMENT_3D('',#39561,#39562,#39563); -#39565=PLANE('',#39564); -#39566=ORIENTED_EDGE('',*,*,#25790,.F.); -#39568=ORIENTED_EDGE('',*,*,#39567,.T.); -#39569=ORIENTED_EDGE('',*,*,#29384,.T.); -#39570=ORIENTED_EDGE('',*,*,#39554,.F.); -#39571=EDGE_LOOP('',(#39566,#39568,#39569,#39570)); -#39572=FACE_OUTER_BOUND('',#39571,.F.); -#39574=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.175E0)); -#39575=DIRECTION('',(8.265988563857E-1,0.E0,-5.627915516617E-1)); -#39576=DIRECTION('',(-5.627915516617E-1,0.E0,-8.265988563857E-1)); -#39577=AXIS2_PLACEMENT_3D('',#39574,#39575,#39576); -#39578=PLANE('',#39577); -#39579=ORIENTED_EDGE('',*,*,#25788,.F.); -#39581=ORIENTED_EDGE('',*,*,#39580,.T.); -#39582=ORIENTED_EDGE('',*,*,#29386,.T.); -#39583=ORIENTED_EDGE('',*,*,#39567,.F.); -#39584=EDGE_LOOP('',(#39579,#39581,#39582,#39583)); -#39585=FACE_OUTER_BOUND('',#39584,.F.); -#39587=CARTESIAN_POINT('',(5.75E0,1.55E0,6.2875E0)); -#39588=DIRECTION('',(9.825817119101E-1,0.E0,-1.858310507417E-1)); -#39589=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#39590=AXIS2_PLACEMENT_3D('',#39587,#39588,#39589); -#39591=PLANE('',#39590); -#39592=ORIENTED_EDGE('',*,*,#25786,.F.); -#39594=ORIENTED_EDGE('',*,*,#39593,.T.); -#39595=ORIENTED_EDGE('',*,*,#29388,.T.); -#39596=ORIENTED_EDGE('',*,*,#39580,.F.); -#39597=EDGE_LOOP('',(#39592,#39594,#39595,#39596)); -#39598=FACE_OUTER_BOUND('',#39597,.F.); -#39600=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.4E0)); -#39601=DIRECTION('',(9.825817119101E-1,0.E0,1.858310507417E-1)); -#39602=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#39603=AXIS2_PLACEMENT_3D('',#39600,#39601,#39602); -#39604=PLANE('',#39603); -#39605=ORIENTED_EDGE('',*,*,#25784,.F.); -#39607=ORIENTED_EDGE('',*,*,#39606,.T.); -#39608=ORIENTED_EDGE('',*,*,#29390,.T.); -#39609=ORIENTED_EDGE('',*,*,#39593,.F.); -#39610=EDGE_LOOP('',(#39605,#39607,#39608,#39609)); -#39611=FACE_OUTER_BOUND('',#39610,.F.); -#39613=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,6.493749856949E0)); -#39614=DIRECTION('',(8.265988563857E-1,0.E0,5.627915516617E-1)); -#39615=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#39616=AXIS2_PLACEMENT_3D('',#39613,#39614,#39615); -#39617=PLANE('',#39616); -#39618=ORIENTED_EDGE('',*,*,#25782,.F.); -#39620=ORIENTED_EDGE('',*,*,#39619,.T.); -#39621=ORIENTED_EDGE('',*,*,#29392,.T.); -#39622=ORIENTED_EDGE('',*,*,#39606,.F.); -#39623=EDGE_LOOP('',(#39618,#39620,#39621,#39622)); -#39624=FACE_OUTER_BOUND('',#39623,.F.); -#39626=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.549999856949E0)); -#39627=DIRECTION('',(6.611562545751E-1,0.E0,7.502482302787E-1)); -#39628=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#39629=AXIS2_PLACEMENT_3D('',#39626,#39627,#39628); -#39630=PLANE('',#39629); -#39631=ORIENTED_EDGE('',*,*,#25780,.F.); -#39633=ORIENTED_EDGE('',*,*,#39632,.T.); -#39634=ORIENTED_EDGE('',*,*,#29394,.T.); -#39635=ORIENTED_EDGE('',*,*,#39619,.F.); -#39636=EDGE_LOOP('',(#39631,#39633,#39634,#39635)); -#39637=FACE_OUTER_BOUND('',#39636,.F.); -#39639=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,6.587500143051E0)); -#39640=DIRECTION('',(4.032202886425E-1,0.E0,9.151029443877E-1)); -#39641=DIRECTION('',(9.151029443877E-1,0.E0,-4.032202886425E-1)); -#39642=AXIS2_PLACEMENT_3D('',#39639,#39640,#39641); -#39643=PLANE('',#39642); -#39644=ORIENTED_EDGE('',*,*,#25778,.F.); -#39646=ORIENTED_EDGE('',*,*,#39645,.T.); -#39647=ORIENTED_EDGE('',*,*,#29396,.T.); -#39648=ORIENTED_EDGE('',*,*,#39632,.F.); -#39649=EDGE_LOOP('',(#39644,#39646,#39647,#39648)); -#39650=FACE_OUTER_BOUND('',#39649,.F.); -#39652=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.606249856949E0)); -#39653=DIRECTION('',(2.818377214504E-1,0.E0,9.594620882388E-1)); -#39654=DIRECTION('',(9.594620882388E-1,0.E0,-2.818377214504E-1)); -#39655=AXIS2_PLACEMENT_3D('',#39652,#39653,#39654); -#39656=PLANE('',#39655); -#39657=ORIENTED_EDGE('',*,*,#25776,.F.); -#39659=ORIENTED_EDGE('',*,*,#39658,.T.); -#39660=ORIENTED_EDGE('',*,*,#29398,.T.); -#39661=ORIENTED_EDGE('',*,*,#39645,.F.); -#39662=EDGE_LOOP('',(#39657,#39659,#39660,#39661)); -#39663=FACE_OUTER_BOUND('',#39662,.F.); -#39665=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,6.625E0)); -#39666=DIRECTION('',(1.735759082829E-1,0.E0,9.848204933204E-1)); -#39667=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#39668=AXIS2_PLACEMENT_3D('',#39665,#39666,#39667); -#39669=PLANE('',#39668); -#39670=ORIENTED_EDGE('',*,*,#25774,.F.); -#39671=ORIENTED_EDGE('',*,*,#39348,.T.); -#39672=ORIENTED_EDGE('',*,*,#29400,.T.); -#39673=ORIENTED_EDGE('',*,*,#39658,.F.); -#39674=EDGE_LOOP('',(#39670,#39671,#39672,#39673)); -#39675=FACE_OUTER_BOUND('',#39674,.F.); -#39677=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.531250143051E0)); -#39678=DIRECTION('',(1.453170680242E-1,0.E0,-9.893851372145E-1)); -#39679=DIRECTION('',(-9.893851372145E-1,0.E0,-1.453170680242E-1)); -#39680=AXIS2_PLACEMENT_3D('',#39677,#39678,#39679); -#39681=PLANE('',#39680); -#39682=ORIENTED_EDGE('',*,*,#26764,.F.); -#39684=ORIENTED_EDGE('',*,*,#39683,.T.); -#39685=ORIENTED_EDGE('',*,*,#29404,.T.); -#39687=ORIENTED_EDGE('',*,*,#39686,.F.); -#39688=EDGE_LOOP('',(#39682,#39684,#39685,#39687)); -#39689=FACE_OUTER_BOUND('',#39688,.F.); -#39691=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.531250143051E0)); -#39692=DIRECTION('',(0.E0,0.E0,-1.E0)); -#39693=DIRECTION('',(-1.E0,0.E0,0.E0)); -#39694=AXIS2_PLACEMENT_3D('',#39691,#39692,#39693); -#39695=PLANE('',#39694); -#39696=ORIENTED_EDGE('',*,*,#26798,.F.); -#39698=ORIENTED_EDGE('',*,*,#39697,.T.); -#39699=ORIENTED_EDGE('',*,*,#29406,.T.); -#39700=ORIENTED_EDGE('',*,*,#39683,.F.); -#39701=EDGE_LOOP('',(#39696,#39698,#39699,#39700)); -#39702=FACE_OUTER_BOUND('',#39701,.F.); -#39704=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.5125E0)); -#39705=DIRECTION('',(-1.453170348161E-1,0.E0,-9.893851420919E-1)); -#39706=DIRECTION('',(-9.893851420919E-1,0.E0,1.453170348161E-1)); -#39707=AXIS2_PLACEMENT_3D('',#39704,#39705,#39706); -#39708=PLANE('',#39707); -#39709=ORIENTED_EDGE('',*,*,#26796,.F.); -#39711=ORIENTED_EDGE('',*,*,#39710,.T.); -#39712=ORIENTED_EDGE('',*,*,#29408,.T.); -#39713=ORIENTED_EDGE('',*,*,#39697,.F.); -#39714=EDGE_LOOP('',(#39709,#39711,#39712,#39713)); -#39715=FACE_OUTER_BOUND('',#39714,.F.); -#39717=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.437499856949E0)); -#39718=DIRECTION('',(-5.065497678209E-1,0.E0,-8.622107240812E-1)); -#39719=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#39720=AXIS2_PLACEMENT_3D('',#39717,#39718,#39719); -#39721=PLANE('',#39720); -#39722=ORIENTED_EDGE('',*,*,#26794,.F.); -#39724=ORIENTED_EDGE('',*,*,#39723,.T.); -#39725=ORIENTED_EDGE('',*,*,#29410,.T.); -#39726=ORIENTED_EDGE('',*,*,#39710,.F.); -#39727=EDGE_LOOP('',(#39722,#39724,#39725,#39726)); -#39728=FACE_OUTER_BOUND('',#39727,.F.); -#39730=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.381249856949E0)); -#39731=DIRECTION('',(-7.975044865771E-1,0.E0,-6.033130148517E-1)); -#39732=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865771E-1)); -#39733=AXIS2_PLACEMENT_3D('',#39730,#39731,#39732); -#39734=PLANE('',#39733); -#39735=ORIENTED_EDGE('',*,*,#26792,.F.); -#39737=ORIENTED_EDGE('',*,*,#39736,.T.); -#39738=ORIENTED_EDGE('',*,*,#29412,.T.); -#39739=ORIENTED_EDGE('',*,*,#39723,.F.); -#39740=EDGE_LOOP('',(#39735,#39737,#39738,#39739)); -#39741=FACE_OUTER_BOUND('',#39740,.F.); -#39743=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,6.2875E0)); -#39744=DIRECTION('',(-9.752006830246E-1,0.E0,-2.213224521559E-1)); -#39745=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#39746=AXIS2_PLACEMENT_3D('',#39743,#39744,#39745); -#39747=PLANE('',#39746); -#39748=ORIENTED_EDGE('',*,*,#26790,.F.); -#39750=ORIENTED_EDGE('',*,*,#39749,.T.); -#39751=ORIENTED_EDGE('',*,*,#29414,.T.); -#39752=ORIENTED_EDGE('',*,*,#39736,.F.); -#39753=EDGE_LOOP('',(#39748,#39750,#39751,#39752)); -#39754=FACE_OUTER_BOUND('',#39753,.F.); -#39756=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.193750143051E0)); -#39757=DIRECTION('',(-9.752006830246E-1,0.E0,2.213224521559E-1)); -#39758=DIRECTION('',(2.213224521559E-1,0.E0,9.752006830246E-1)); -#39759=AXIS2_PLACEMENT_3D('',#39756,#39757,#39758); -#39760=PLANE('',#39759); -#39761=ORIENTED_EDGE('',*,*,#26788,.F.); -#39763=ORIENTED_EDGE('',*,*,#39762,.T.); -#39764=ORIENTED_EDGE('',*,*,#29416,.T.); -#39765=ORIENTED_EDGE('',*,*,#39749,.F.); -#39766=EDGE_LOOP('',(#39761,#39763,#39764,#39765)); -#39767=FACE_OUTER_BOUND('',#39766,.F.); -#39769=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,6.137500143051E0)); -#39770=DIRECTION('',(-7.975044865771E-1,0.E0,6.033130148517E-1)); -#39771=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#39772=AXIS2_PLACEMENT_3D('',#39769,#39770,#39771); -#39773=PLANE('',#39772); -#39774=ORIENTED_EDGE('',*,*,#26786,.F.); -#39776=ORIENTED_EDGE('',*,*,#39775,.T.); -#39777=ORIENTED_EDGE('',*,*,#29418,.T.); -#39778=ORIENTED_EDGE('',*,*,#39762,.F.); -#39779=EDGE_LOOP('',(#39774,#39776,#39777,#39778)); -#39780=FACE_OUTER_BOUND('',#39779,.F.); -#39782=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,6.0625E0)); -#39783=DIRECTION('',(-5.065497678209E-1,0.E0,8.622107240812E-1)); -#39784=DIRECTION('',(8.622107240812E-1,0.E0,5.065497678209E-1)); -#39785=AXIS2_PLACEMENT_3D('',#39782,#39783,#39784); -#39786=PLANE('',#39785); -#39787=ORIENTED_EDGE('',*,*,#26784,.F.); -#39789=ORIENTED_EDGE('',*,*,#39788,.T.); -#39790=ORIENTED_EDGE('',*,*,#29420,.T.); -#39791=ORIENTED_EDGE('',*,*,#39775,.F.); -#39792=EDGE_LOOP('',(#39787,#39789,#39790,#39791)); -#39793=FACE_OUTER_BOUND('',#39792,.F.); -#39795=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,6.043749856949E0)); -#39796=DIRECTION('',(-1.453170348161E-1,0.E0,9.893851420919E-1)); -#39797=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#39798=AXIS2_PLACEMENT_3D('',#39795,#39796,#39797); -#39799=PLANE('',#39798); -#39800=ORIENTED_EDGE('',*,*,#26782,.F.); -#39802=ORIENTED_EDGE('',*,*,#39801,.T.); -#39803=ORIENTED_EDGE('',*,*,#29422,.T.); -#39804=ORIENTED_EDGE('',*,*,#39788,.F.); -#39805=EDGE_LOOP('',(#39800,#39802,#39803,#39804)); -#39806=FACE_OUTER_BOUND('',#39805,.F.); -#39808=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,6.043749856949E0)); -#39809=DIRECTION('',(0.E0,0.E0,1.E0)); -#39810=DIRECTION('',(1.E0,0.E0,0.E0)); -#39811=AXIS2_PLACEMENT_3D('',#39808,#39809,#39810); -#39812=PLANE('',#39811); -#39813=ORIENTED_EDGE('',*,*,#26780,.F.); -#39815=ORIENTED_EDGE('',*,*,#39814,.T.); -#39816=ORIENTED_EDGE('',*,*,#29424,.T.); -#39817=ORIENTED_EDGE('',*,*,#39801,.F.); -#39818=EDGE_LOOP('',(#39813,#39815,#39816,#39817)); -#39819=FACE_OUTER_BOUND('',#39818,.F.); -#39821=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.0625E0)); -#39822=DIRECTION('',(1.453170680242E-1,0.E0,9.893851372145E-1)); -#39823=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#39824=AXIS2_PLACEMENT_3D('',#39821,#39822,#39823); -#39825=PLANE('',#39824); -#39826=ORIENTED_EDGE('',*,*,#26778,.F.); -#39828=ORIENTED_EDGE('',*,*,#39827,.T.); -#39829=ORIENTED_EDGE('',*,*,#29426,.T.); -#39830=ORIENTED_EDGE('',*,*,#39814,.F.); -#39831=EDGE_LOOP('',(#39826,#39828,#39829,#39830)); -#39832=FACE_OUTER_BOUND('',#39831,.F.); -#39834=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.137500143051E0)); -#39835=DIRECTION('',(5.065496359537E-1,0.E0,8.622108015533E-1)); -#39836=DIRECTION('',(8.622108015533E-1,0.E0,-5.065496359537E-1)); -#39837=AXIS2_PLACEMENT_3D('',#39834,#39835,#39836); -#39838=PLANE('',#39837); -#39839=ORIENTED_EDGE('',*,*,#26776,.F.); -#39841=ORIENTED_EDGE('',*,*,#39840,.T.); -#39842=ORIENTED_EDGE('',*,*,#29428,.T.); -#39843=ORIENTED_EDGE('',*,*,#39827,.F.); -#39844=EDGE_LOOP('',(#39839,#39841,#39842,#39843)); -#39845=FACE_OUTER_BOUND('',#39844,.F.); -#39847=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.193750143051E0)); -#39848=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#39849=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#39850=AXIS2_PLACEMENT_3D('',#39847,#39848,#39849); -#39851=PLANE('',#39850); -#39852=ORIENTED_EDGE('',*,*,#26774,.F.); -#39854=ORIENTED_EDGE('',*,*,#39853,.T.); -#39855=ORIENTED_EDGE('',*,*,#29430,.T.); -#39856=ORIENTED_EDGE('',*,*,#39840,.F.); -#39857=EDGE_LOOP('',(#39852,#39854,#39855,#39856)); -#39858=FACE_OUTER_BOUND('',#39857,.F.); -#39860=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.2875E0)); -#39861=DIRECTION('',(9.752006830246E-1,0.E0,2.213224521559E-1)); -#39862=DIRECTION('',(2.213224521559E-1,0.E0,-9.752006830246E-1)); -#39863=AXIS2_PLACEMENT_3D('',#39860,#39861,#39862); -#39864=PLANE('',#39863); -#39865=ORIENTED_EDGE('',*,*,#26772,.F.); -#39867=ORIENTED_EDGE('',*,*,#39866,.T.); -#39868=ORIENTED_EDGE('',*,*,#29432,.T.); -#39869=ORIENTED_EDGE('',*,*,#39853,.F.); -#39870=EDGE_LOOP('',(#39865,#39867,#39868,#39869)); -#39871=FACE_OUTER_BOUND('',#39870,.F.); -#39873=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.381249856949E0)); -#39874=DIRECTION('',(9.752006830246E-1,0.E0,-2.213224521559E-1)); -#39875=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#39876=AXIS2_PLACEMENT_3D('',#39873,#39874,#39875); -#39877=PLANE('',#39876); -#39878=ORIENTED_EDGE('',*,*,#26770,.F.); -#39880=ORIENTED_EDGE('',*,*,#39879,.T.); -#39881=ORIENTED_EDGE('',*,*,#29434,.T.); -#39882=ORIENTED_EDGE('',*,*,#39866,.F.); -#39883=EDGE_LOOP('',(#39878,#39880,#39881,#39882)); -#39884=FACE_OUTER_BOUND('',#39883,.F.); -#39886=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.437499856949E0)); -#39887=DIRECTION('',(7.975044865771E-1,0.E0,-6.033130148517E-1)); -#39888=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865771E-1)); -#39889=AXIS2_PLACEMENT_3D('',#39886,#39887,#39888); -#39890=PLANE('',#39889); -#39891=ORIENTED_EDGE('',*,*,#26768,.F.); -#39893=ORIENTED_EDGE('',*,*,#39892,.T.); -#39894=ORIENTED_EDGE('',*,*,#29436,.T.); -#39895=ORIENTED_EDGE('',*,*,#39879,.F.); -#39896=EDGE_LOOP('',(#39891,#39893,#39894,#39895)); -#39897=FACE_OUTER_BOUND('',#39896,.F.); -#39899=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,6.5125E0)); -#39900=DIRECTION('',(5.065496359537E-1,0.E0,-8.622108015533E-1)); -#39901=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#39902=AXIS2_PLACEMENT_3D('',#39899,#39900,#39901); -#39903=PLANE('',#39902); -#39904=ORIENTED_EDGE('',*,*,#26766,.F.); -#39905=ORIENTED_EDGE('',*,*,#39686,.T.); -#39906=ORIENTED_EDGE('',*,*,#29438,.T.); -#39907=ORIENTED_EDGE('',*,*,#39892,.F.); -#39908=EDGE_LOOP('',(#39904,#39905,#39906,#39907)); -#39909=FACE_OUTER_BOUND('',#39908,.F.); -#39911=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.800000143051E0)); -#39912=DIRECTION('',(0.E0,0.E0,1.E0)); -#39913=DIRECTION('',(1.E0,0.E0,0.E0)); -#39914=AXIS2_PLACEMENT_3D('',#39911,#39912,#39913); -#39915=PLANE('',#39914); -#39916=ORIENTED_EDGE('',*,*,#25826,.F.); -#39918=ORIENTED_EDGE('',*,*,#39917,.T.); -#39919=ORIENTED_EDGE('',*,*,#29455,.T.); -#39921=ORIENTED_EDGE('',*,*,#39920,.F.); -#39922=EDGE_LOOP('',(#39916,#39918,#39919,#39921)); -#39923=FACE_OUTER_BOUND('',#39922,.F.); -#39925=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.78125E0)); -#39926=DIRECTION('',(-1.735759554437E-1,0.E0,9.848204850082E-1)); -#39927=DIRECTION('',(9.848204850082E-1,0.E0,1.735759554437E-1)); -#39928=AXIS2_PLACEMENT_3D('',#39925,#39926,#39927); -#39929=PLANE('',#39928); -#39930=ORIENTED_EDGE('',*,*,#25876,.F.); -#39932=ORIENTED_EDGE('',*,*,#39931,.T.); -#39933=ORIENTED_EDGE('',*,*,#29457,.T.); -#39934=ORIENTED_EDGE('',*,*,#39917,.F.); -#39935=EDGE_LOOP('',(#39930,#39932,#39933,#39934)); -#39936=FACE_OUTER_BOUND('',#39935,.F.); -#39938=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.762499856949E0)); -#39939=DIRECTION('',(-2.818434175982E-1,0.E0,9.594604150024E-1)); -#39940=DIRECTION('',(9.594604150024E-1,0.E0,2.818434175982E-1)); -#39941=AXIS2_PLACEMENT_3D('',#39938,#39939,#39940); -#39942=PLANE('',#39941); -#39943=ORIENTED_EDGE('',*,*,#25874,.F.); -#39945=ORIENTED_EDGE('',*,*,#39944,.T.); -#39946=ORIENTED_EDGE('',*,*,#29459,.T.); -#39947=ORIENTED_EDGE('',*,*,#39931,.F.); -#39948=EDGE_LOOP('',(#39943,#39945,#39946,#39947)); -#39949=FACE_OUTER_BOUND('',#39948,.F.); -#39951=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.725E0)); -#39952=DIRECTION('',(-4.032164835459E-1,0.E0,9.151046210116E-1)); -#39953=DIRECTION('',(9.151046210116E-1,0.E0,4.032164835459E-1)); -#39954=AXIS2_PLACEMENT_3D('',#39951,#39952,#39953); -#39955=PLANE('',#39954); -#39956=ORIENTED_EDGE('',*,*,#25872,.F.); -#39958=ORIENTED_EDGE('',*,*,#39957,.T.); -#39959=ORIENTED_EDGE('',*,*,#29461,.T.); -#39960=ORIENTED_EDGE('',*,*,#39944,.F.); -#39961=EDGE_LOOP('',(#39956,#39958,#39959,#39960)); -#39962=FACE_OUTER_BOUND('',#39961,.F.); -#39964=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.66875E0)); -#39965=DIRECTION('',(-6.611562980142E-1,0.E0,7.502481919980E-1)); -#39966=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#39967=AXIS2_PLACEMENT_3D('',#39964,#39965,#39966); -#39968=PLANE('',#39967); -#39969=ORIENTED_EDGE('',*,*,#25870,.F.); -#39971=ORIENTED_EDGE('',*,*,#39970,.T.); -#39972=ORIENTED_EDGE('',*,*,#29463,.T.); -#39973=ORIENTED_EDGE('',*,*,#39957,.F.); -#39974=EDGE_LOOP('',(#39969,#39971,#39972,#39973)); -#39975=FACE_OUTER_BOUND('',#39974,.F.); -#39977=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.575000143051E0)); -#39978=DIRECTION('',(-8.265988793059E-1,0.E0,5.627915179978E-1)); -#39979=DIRECTION('',(5.627915179978E-1,0.E0,8.265988793059E-1)); -#39980=AXIS2_PLACEMENT_3D('',#39977,#39978,#39979); -#39981=PLANE('',#39980); -#39982=ORIENTED_EDGE('',*,*,#25868,.F.); -#39984=ORIENTED_EDGE('',*,*,#39983,.T.); -#39985=ORIENTED_EDGE('',*,*,#29465,.T.); -#39986=ORIENTED_EDGE('',*,*,#39970,.F.); -#39987=EDGE_LOOP('',(#39982,#39984,#39985,#39986)); -#39988=FACE_OUTER_BOUND('',#39987,.F.); -#39990=CARTESIAN_POINT('',(4.75E0,1.55E0,5.462500143051E0)); -#39991=DIRECTION('',(-9.825817148807E-1,0.E0,1.858310350350E-1)); -#39992=DIRECTION('',(1.858310350350E-1,0.E0,9.825817148807E-1)); -#39993=AXIS2_PLACEMENT_3D('',#39990,#39991,#39992); -#39994=PLANE('',#39993); -#39995=ORIENTED_EDGE('',*,*,#25866,.F.); -#39997=ORIENTED_EDGE('',*,*,#39996,.T.); -#39998=ORIENTED_EDGE('',*,*,#29467,.T.); -#39999=ORIENTED_EDGE('',*,*,#39983,.F.); -#40000=EDGE_LOOP('',(#39995,#39997,#39998,#39999)); -#40001=FACE_OUTER_BOUND('',#40000,.F.); -#40003=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,5.350000143051E0)); -#40004=DIRECTION('',(-9.825817148807E-1,0.E0,-1.858310350350E-1)); -#40005=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#40006=AXIS2_PLACEMENT_3D('',#40003,#40004,#40005); -#40007=PLANE('',#40006); -#40008=ORIENTED_EDGE('',*,*,#25864,.F.); -#40010=ORIENTED_EDGE('',*,*,#40009,.T.); -#40011=ORIENTED_EDGE('',*,*,#29469,.T.); -#40012=ORIENTED_EDGE('',*,*,#39996,.F.); -#40013=EDGE_LOOP('',(#40008,#40010,#40011,#40012)); -#40014=FACE_OUTER_BOUND('',#40013,.F.); -#40016=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,5.256249856949E0)); -#40017=DIRECTION('',(-8.266000777833E-1,0.E0,-5.627897577325E-1)); -#40018=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#40019=AXIS2_PLACEMENT_3D('',#40016,#40017,#40018); -#40020=PLANE('',#40019); -#40021=ORIENTED_EDGE('',*,*,#25862,.F.); -#40023=ORIENTED_EDGE('',*,*,#40022,.T.); -#40024=ORIENTED_EDGE('',*,*,#29471,.T.); -#40025=ORIENTED_EDGE('',*,*,#40009,.F.); -#40026=EDGE_LOOP('',(#40021,#40023,#40024,#40025)); -#40027=FACE_OUTER_BOUND('',#40026,.F.); -#40029=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,5.199999856949E0)); -#40030=DIRECTION('',(-6.611562980142E-1,0.E0,-7.502481919980E-1)); -#40031=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#40032=AXIS2_PLACEMENT_3D('',#40029,#40030,#40031); -#40033=PLANE('',#40032); -#40034=ORIENTED_EDGE('',*,*,#25860,.F.); -#40036=ORIENTED_EDGE('',*,*,#40035,.T.); -#40037=ORIENTED_EDGE('',*,*,#29473,.T.); -#40038=ORIENTED_EDGE('',*,*,#40022,.F.); -#40039=EDGE_LOOP('',(#40034,#40036,#40037,#40038)); -#40040=FACE_OUTER_BOUND('',#40039,.F.); -#40042=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.1625E0)); -#40043=DIRECTION('',(-4.032164835459E-1,0.E0,-9.151046210116E-1)); -#40044=DIRECTION('',(-9.151046210116E-1,0.E0,4.032164835459E-1)); -#40045=AXIS2_PLACEMENT_3D('',#40042,#40043,#40044); -#40046=PLANE('',#40045); -#40047=ORIENTED_EDGE('',*,*,#25858,.F.); -#40049=ORIENTED_EDGE('',*,*,#40048,.T.); -#40050=ORIENTED_EDGE('',*,*,#29475,.T.); -#40051=ORIENTED_EDGE('',*,*,#40035,.F.); -#40052=EDGE_LOOP('',(#40047,#40049,#40050,#40051)); -#40053=FACE_OUTER_BOUND('',#40052,.F.); -#40055=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.143749856949E0)); -#40056=DIRECTION('',(-2.818434175982E-1,0.E0,-9.594604150024E-1)); -#40057=DIRECTION('',(-9.594604150024E-1,0.E0,2.818434175982E-1)); -#40058=AXIS2_PLACEMENT_3D('',#40055,#40056,#40057); -#40059=PLANE('',#40058); -#40060=ORIENTED_EDGE('',*,*,#25856,.F.); -#40062=ORIENTED_EDGE('',*,*,#40061,.T.); -#40063=ORIENTED_EDGE('',*,*,#29477,.T.); -#40064=ORIENTED_EDGE('',*,*,#40048,.F.); -#40065=EDGE_LOOP('',(#40060,#40062,#40063,#40064)); -#40066=FACE_OUTER_BOUND('',#40065,.F.); -#40068=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,5.125000143051E0)); -#40069=DIRECTION('',(-1.735721023269E-1,0.E0,-9.848211641175E-1)); -#40070=DIRECTION('',(-9.848211641175E-1,0.E0,1.735721023269E-1)); -#40071=AXIS2_PLACEMENT_3D('',#40068,#40069,#40070); -#40072=PLANE('',#40071); -#40073=ORIENTED_EDGE('',*,*,#25854,.F.); -#40075=ORIENTED_EDGE('',*,*,#40074,.T.); -#40076=ORIENTED_EDGE('',*,*,#29479,.T.); -#40077=ORIENTED_EDGE('',*,*,#40061,.F.); -#40078=EDGE_LOOP('',(#40073,#40075,#40076,#40077)); -#40079=FACE_OUTER_BOUND('',#40078,.F.); -#40081=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.125000143051E0)); -#40082=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40083=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40084=AXIS2_PLACEMENT_3D('',#40081,#40082,#40083); -#40085=PLANE('',#40084); -#40086=ORIENTED_EDGE('',*,*,#25852,.F.); -#40088=ORIENTED_EDGE('',*,*,#40087,.T.); -#40089=ORIENTED_EDGE('',*,*,#29481,.T.); -#40090=ORIENTED_EDGE('',*,*,#40074,.F.); -#40091=EDGE_LOOP('',(#40086,#40088,#40089,#40090)); -#40092=FACE_OUTER_BOUND('',#40091,.F.); -#40094=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.143749856949E0)); -#40095=DIRECTION('',(1.735720551671E-1,0.E0,-9.848211724293E-1)); -#40096=DIRECTION('',(-9.848211724293E-1,0.E0,-1.735720551671E-1)); -#40097=AXIS2_PLACEMENT_3D('',#40094,#40095,#40096); -#40098=PLANE('',#40097); -#40099=ORIENTED_EDGE('',*,*,#25850,.F.); -#40101=ORIENTED_EDGE('',*,*,#40100,.T.); -#40102=ORIENTED_EDGE('',*,*,#29483,.T.); -#40103=ORIENTED_EDGE('',*,*,#40087,.F.); -#40104=EDGE_LOOP('',(#40099,#40101,#40102,#40103)); -#40105=FACE_OUTER_BOUND('',#40104,.F.); -#40107=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.1625E0)); -#40108=DIRECTION('',(2.818436598788E-1,0.E0,-9.594603438319E-1)); -#40109=DIRECTION('',(-9.594603438319E-1,0.E0,-2.818436598788E-1)); -#40110=AXIS2_PLACEMENT_3D('',#40107,#40108,#40109); -#40111=PLANE('',#40110); -#40112=ORIENTED_EDGE('',*,*,#25848,.F.); -#40114=ORIENTED_EDGE('',*,*,#40113,.T.); -#40115=ORIENTED_EDGE('',*,*,#29485,.T.); -#40116=ORIENTED_EDGE('',*,*,#40100,.F.); -#40117=EDGE_LOOP('',(#40112,#40114,#40115,#40116)); -#40118=FACE_OUTER_BOUND('',#40117,.F.); -#40120=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.199999856949E0)); -#40121=DIRECTION('',(4.032164244255E-1,0.E0,-9.151046470615E-1)); -#40122=DIRECTION('',(-9.151046470615E-1,0.E0,-4.032164244255E-1)); -#40123=AXIS2_PLACEMENT_3D('',#40120,#40121,#40122); -#40124=PLANE('',#40123); -#40125=ORIENTED_EDGE('',*,*,#25846,.F.); -#40127=ORIENTED_EDGE('',*,*,#40126,.T.); -#40128=ORIENTED_EDGE('',*,*,#29487,.T.); -#40129=ORIENTED_EDGE('',*,*,#40113,.F.); -#40130=EDGE_LOOP('',(#40125,#40127,#40128,#40129)); -#40131=FACE_OUTER_BOUND('',#40130,.F.); -#40133=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.256249856949E0)); -#40134=DIRECTION('',(6.611562545751E-1,0.E0,-7.502482302787E-1)); -#40135=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#40136=AXIS2_PLACEMENT_3D('',#40133,#40134,#40135); -#40137=PLANE('',#40136); -#40138=ORIENTED_EDGE('',*,*,#25844,.F.); -#40140=ORIENTED_EDGE('',*,*,#40139,.T.); -#40141=ORIENTED_EDGE('',*,*,#29489,.T.); -#40142=ORIENTED_EDGE('',*,*,#40126,.F.); -#40143=EDGE_LOOP('',(#40138,#40140,#40141,#40142)); -#40144=FACE_OUTER_BOUND('',#40143,.F.); -#40146=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.350000143051E0)); -#40147=DIRECTION('',(8.266000548632E-1,0.E0,-5.627897913965E-1)); -#40148=DIRECTION('',(-5.627897913965E-1,0.E0,-8.266000548632E-1)); -#40149=AXIS2_PLACEMENT_3D('',#40146,#40147,#40148); -#40150=PLANE('',#40149); -#40151=ORIENTED_EDGE('',*,*,#25842,.F.); -#40153=ORIENTED_EDGE('',*,*,#40152,.T.); -#40154=ORIENTED_EDGE('',*,*,#29491,.T.); -#40155=ORIENTED_EDGE('',*,*,#40139,.F.); -#40156=EDGE_LOOP('',(#40151,#40153,#40154,#40155)); -#40157=FACE_OUTER_BOUND('',#40156,.F.); -#40159=CARTESIAN_POINT('',(5.75E0,1.55E0,5.462500143051E0)); -#40160=DIRECTION('',(9.825817119101E-1,0.E0,-1.858310507417E-1)); -#40161=DIRECTION('',(-1.858310507417E-1,0.E0,-9.825817119101E-1)); -#40162=AXIS2_PLACEMENT_3D('',#40159,#40160,#40161); -#40163=PLANE('',#40162); -#40164=ORIENTED_EDGE('',*,*,#25840,.F.); -#40166=ORIENTED_EDGE('',*,*,#40165,.T.); -#40167=ORIENTED_EDGE('',*,*,#29493,.T.); -#40168=ORIENTED_EDGE('',*,*,#40152,.F.); -#40169=EDGE_LOOP('',(#40164,#40166,#40167,#40168)); -#40170=FACE_OUTER_BOUND('',#40169,.F.); -#40172=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,5.575000143051E0)); -#40173=DIRECTION('',(9.825817119101E-1,0.E0,1.858310507417E-1)); -#40174=DIRECTION('',(1.858310507417E-1,0.E0,-9.825817119101E-1)); -#40175=AXIS2_PLACEMENT_3D('',#40172,#40173,#40174); -#40176=PLANE('',#40175); -#40177=ORIENTED_EDGE('',*,*,#25838,.F.); -#40179=ORIENTED_EDGE('',*,*,#40178,.T.); -#40180=ORIENTED_EDGE('',*,*,#29495,.T.); -#40181=ORIENTED_EDGE('',*,*,#40165,.F.); -#40182=EDGE_LOOP('',(#40177,#40179,#40180,#40181)); -#40183=FACE_OUTER_BOUND('',#40182,.F.); -#40185=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,5.66875E0)); -#40186=DIRECTION('',(8.265988563857E-1,0.E0,5.627915516617E-1)); -#40187=DIRECTION('',(5.627915516617E-1,0.E0,-8.265988563857E-1)); -#40188=AXIS2_PLACEMENT_3D('',#40185,#40186,#40187); -#40189=PLANE('',#40188); -#40190=ORIENTED_EDGE('',*,*,#25836,.F.); -#40192=ORIENTED_EDGE('',*,*,#40191,.T.); -#40193=ORIENTED_EDGE('',*,*,#29497,.T.); -#40194=ORIENTED_EDGE('',*,*,#40178,.F.); -#40195=EDGE_LOOP('',(#40190,#40192,#40193,#40194)); -#40196=FACE_OUTER_BOUND('',#40195,.F.); -#40198=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,5.725E0)); -#40199=DIRECTION('',(6.611562545751E-1,0.E0,7.502482302787E-1)); -#40200=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#40201=AXIS2_PLACEMENT_3D('',#40198,#40199,#40200); -#40202=PLANE('',#40201); -#40203=ORIENTED_EDGE('',*,*,#25834,.F.); -#40205=ORIENTED_EDGE('',*,*,#40204,.T.); -#40206=ORIENTED_EDGE('',*,*,#29499,.T.); -#40207=ORIENTED_EDGE('',*,*,#40191,.F.); -#40208=EDGE_LOOP('',(#40203,#40205,#40206,#40207)); -#40209=FACE_OUTER_BOUND('',#40208,.F.); -#40211=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.762499856949E0)); -#40212=DIRECTION('',(4.032164244255E-1,0.E0,9.151046470615E-1)); -#40213=DIRECTION('',(9.151046470615E-1,0.E0,-4.032164244255E-1)); -#40214=AXIS2_PLACEMENT_3D('',#40211,#40212,#40213); -#40215=PLANE('',#40214); -#40216=ORIENTED_EDGE('',*,*,#25832,.F.); -#40218=ORIENTED_EDGE('',*,*,#40217,.T.); -#40219=ORIENTED_EDGE('',*,*,#29501,.T.); -#40220=ORIENTED_EDGE('',*,*,#40204,.F.); -#40221=EDGE_LOOP('',(#40216,#40218,#40219,#40220)); -#40222=FACE_OUTER_BOUND('',#40221,.F.); -#40224=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.78125E0)); -#40225=DIRECTION('',(2.818436598788E-1,0.E0,9.594603438319E-1)); -#40226=DIRECTION('',(9.594603438319E-1,0.E0,-2.818436598788E-1)); -#40227=AXIS2_PLACEMENT_3D('',#40224,#40225,#40226); -#40228=PLANE('',#40227); -#40229=ORIENTED_EDGE('',*,*,#25830,.F.); -#40231=ORIENTED_EDGE('',*,*,#40230,.T.); -#40232=ORIENTED_EDGE('',*,*,#29503,.T.); -#40233=ORIENTED_EDGE('',*,*,#40217,.F.); -#40234=EDGE_LOOP('',(#40229,#40231,#40232,#40233)); -#40235=FACE_OUTER_BOUND('',#40234,.F.); -#40237=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.800000143051E0)); -#40238=DIRECTION('',(1.735759082829E-1,0.E0,9.848204933204E-1)); -#40239=DIRECTION('',(9.848204933204E-1,0.E0,-1.735759082829E-1)); -#40240=AXIS2_PLACEMENT_3D('',#40237,#40238,#40239); -#40241=PLANE('',#40240); -#40242=ORIENTED_EDGE('',*,*,#25828,.F.); -#40243=ORIENTED_EDGE('',*,*,#39920,.T.); -#40244=ORIENTED_EDGE('',*,*,#29505,.T.); -#40245=ORIENTED_EDGE('',*,*,#40230,.F.); -#40246=EDGE_LOOP('',(#40242,#40243,#40244,#40245)); -#40247=FACE_OUTER_BOUND('',#40246,.F.); -#40249=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.706249856949E0)); -#40250=DIRECTION('',(1.453138122392E-1,0.E0,-9.893856154061E-1)); -#40251=DIRECTION('',(-9.893856154061E-1,0.E0,-1.453138122392E-1)); -#40252=AXIS2_PLACEMENT_3D('',#40249,#40250,#40251); -#40253=PLANE('',#40252); -#40254=ORIENTED_EDGE('',*,*,#26808,.F.); -#40256=ORIENTED_EDGE('',*,*,#40255,.T.); -#40257=ORIENTED_EDGE('',*,*,#29509,.T.); -#40259=ORIENTED_EDGE('',*,*,#40258,.F.); -#40260=EDGE_LOOP('',(#40254,#40256,#40257,#40259)); -#40261=FACE_OUTER_BOUND('',#40260,.F.); -#40263=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.706249856949E0)); -#40264=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40265=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40266=AXIS2_PLACEMENT_3D('',#40263,#40264,#40265); -#40267=PLANE('',#40266); -#40268=ORIENTED_EDGE('',*,*,#26842,.F.); -#40270=ORIENTED_EDGE('',*,*,#40269,.T.); -#40271=ORIENTED_EDGE('',*,*,#29511,.T.); -#40272=ORIENTED_EDGE('',*,*,#40255,.F.); -#40273=EDGE_LOOP('',(#40268,#40270,#40271,#40272)); -#40274=FACE_OUTER_BOUND('',#40273,.F.); -#40276=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.687500143051E0)); -#40277=DIRECTION('',(-1.453137790318E-1,0.E0,-9.893856202834E-1)); -#40278=DIRECTION('',(-9.893856202834E-1,0.E0,1.453137790318E-1)); -#40279=AXIS2_PLACEMENT_3D('',#40276,#40277,#40278); -#40280=PLANE('',#40279); -#40281=ORIENTED_EDGE('',*,*,#26840,.F.); -#40283=ORIENTED_EDGE('',*,*,#40282,.T.); -#40284=ORIENTED_EDGE('',*,*,#29513,.T.); -#40285=ORIENTED_EDGE('',*,*,#40269,.F.); -#40286=EDGE_LOOP('',(#40281,#40283,#40284,#40285)); -#40287=FACE_OUTER_BOUND('',#40286,.F.); -#40289=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.6125E0)); -#40290=DIRECTION('',(-5.065497678209E-1,0.E0,-8.622107240812E-1)); -#40291=DIRECTION('',(-8.622107240812E-1,0.E0,5.065497678209E-1)); -#40292=AXIS2_PLACEMENT_3D('',#40289,#40290,#40291); -#40293=PLANE('',#40292); -#40294=ORIENTED_EDGE('',*,*,#26838,.F.); -#40296=ORIENTED_EDGE('',*,*,#40295,.T.); -#40297=ORIENTED_EDGE('',*,*,#29515,.T.); -#40298=ORIENTED_EDGE('',*,*,#40282,.F.); -#40299=EDGE_LOOP('',(#40294,#40296,#40297,#40298)); -#40300=FACE_OUTER_BOUND('',#40299,.F.); -#40302=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.55625E0)); -#40303=DIRECTION('',(-7.975044865771E-1,0.E0,-6.033130148517E-1)); -#40304=DIRECTION('',(-6.033130148517E-1,0.E0,7.975044865771E-1)); -#40305=AXIS2_PLACEMENT_3D('',#40302,#40303,#40304); -#40306=PLANE('',#40305); -#40307=ORIENTED_EDGE('',*,*,#26836,.F.); -#40309=ORIENTED_EDGE('',*,*,#40308,.T.); -#40310=ORIENTED_EDGE('',*,*,#29517,.T.); -#40311=ORIENTED_EDGE('',*,*,#40295,.F.); -#40312=EDGE_LOOP('',(#40307,#40309,#40310,#40311)); -#40313=FACE_OUTER_BOUND('',#40312,.F.); -#40315=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.462500143051E0)); -#40316=DIRECTION('',(-9.752006830246E-1,0.E0,-2.213224521559E-1)); -#40317=DIRECTION('',(-2.213224521559E-1,0.E0,9.752006830246E-1)); -#40318=AXIS2_PLACEMENT_3D('',#40315,#40316,#40317); -#40319=PLANE('',#40318); -#40320=ORIENTED_EDGE('',*,*,#26834,.F.); -#40322=ORIENTED_EDGE('',*,*,#40321,.T.); -#40323=ORIENTED_EDGE('',*,*,#29519,.T.); -#40324=ORIENTED_EDGE('',*,*,#40308,.F.); -#40325=EDGE_LOOP('',(#40320,#40322,#40323,#40324)); -#40326=FACE_OUTER_BOUND('',#40325,.F.); -#40328=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,5.368749856949E0)); -#40329=DIRECTION('',(-9.752009016921E-1,0.E0,2.213214886517E-1)); -#40330=DIRECTION('',(2.213214886517E-1,0.E0,9.752009016921E-1)); -#40331=AXIS2_PLACEMENT_3D('',#40328,#40329,#40330); -#40332=PLANE('',#40331); -#40333=ORIENTED_EDGE('',*,*,#26832,.F.); -#40335=ORIENTED_EDGE('',*,*,#40334,.T.); -#40336=ORIENTED_EDGE('',*,*,#29521,.T.); -#40337=ORIENTED_EDGE('',*,*,#40321,.F.); -#40338=EDGE_LOOP('',(#40333,#40335,#40336,#40337)); -#40339=FACE_OUTER_BOUND('',#40338,.F.); -#40341=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,5.312499856949E0)); -#40342=DIRECTION('',(-7.975044865771E-1,0.E0,6.033130148517E-1)); -#40343=DIRECTION('',(6.033130148517E-1,0.E0,7.975044865771E-1)); -#40344=AXIS2_PLACEMENT_3D('',#40341,#40342,#40343); -#40345=PLANE('',#40344); -#40346=ORIENTED_EDGE('',*,*,#26830,.F.); -#40348=ORIENTED_EDGE('',*,*,#40347,.T.); -#40349=ORIENTED_EDGE('',*,*,#29523,.T.); -#40350=ORIENTED_EDGE('',*,*,#40334,.F.); -#40351=EDGE_LOOP('',(#40346,#40348,#40349,#40350)); -#40352=FACE_OUTER_BOUND('',#40351,.F.); -#40354=CARTESIAN_POINT('',(5.452127665281E0,1.55E0,5.237500143051E0)); -#40355=DIRECTION('',(-5.065476130533E-1,0.E0,8.622119900059E-1)); -#40356=DIRECTION('',(8.622119900059E-1,0.E0,5.065476130533E-1)); -#40357=AXIS2_PLACEMENT_3D('',#40354,#40355,#40356); -#40358=PLANE('',#40357); -#40359=ORIENTED_EDGE('',*,*,#26828,.F.); -#40361=ORIENTED_EDGE('',*,*,#40360,.T.); -#40362=ORIENTED_EDGE('',*,*,#29525,.T.); -#40363=ORIENTED_EDGE('',*,*,#40347,.F.); -#40364=EDGE_LOOP('',(#40359,#40361,#40362,#40363)); -#40365=FACE_OUTER_BOUND('',#40364,.F.); -#40367=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,5.21875E0)); -#40368=DIRECTION('',(-1.453170348161E-1,0.E0,9.893851420919E-1)); -#40369=DIRECTION('',(9.893851420919E-1,0.E0,1.453170348161E-1)); -#40370=AXIS2_PLACEMENT_3D('',#40367,#40368,#40369); -#40371=PLANE('',#40370); -#40372=ORIENTED_EDGE('',*,*,#26826,.F.); -#40374=ORIENTED_EDGE('',*,*,#40373,.T.); -#40375=ORIENTED_EDGE('',*,*,#29527,.T.); -#40376=ORIENTED_EDGE('',*,*,#40360,.F.); -#40377=EDGE_LOOP('',(#40372,#40374,#40375,#40376)); -#40378=FACE_OUTER_BOUND('',#40377,.F.); -#40380=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.21875E0)); -#40381=DIRECTION('',(0.E0,0.E0,1.E0)); -#40382=DIRECTION('',(1.E0,0.E0,0.E0)); -#40383=AXIS2_PLACEMENT_3D('',#40380,#40381,#40382); -#40384=PLANE('',#40383); -#40385=ORIENTED_EDGE('',*,*,#26824,.F.); -#40387=ORIENTED_EDGE('',*,*,#40386,.T.); -#40388=ORIENTED_EDGE('',*,*,#29529,.T.); -#40389=ORIENTED_EDGE('',*,*,#40373,.F.); -#40390=EDGE_LOOP('',(#40385,#40387,#40388,#40389)); -#40391=FACE_OUTER_BOUND('',#40390,.F.); -#40393=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.237500143051E0)); -#40394=DIRECTION('',(1.453170680242E-1,0.E0,9.893851372145E-1)); -#40395=DIRECTION('',(9.893851372145E-1,0.E0,-1.453170680242E-1)); -#40396=AXIS2_PLACEMENT_3D('',#40393,#40394,#40395); -#40397=PLANE('',#40396); -#40398=ORIENTED_EDGE('',*,*,#26822,.F.); -#40400=ORIENTED_EDGE('',*,*,#40399,.T.); -#40401=ORIENTED_EDGE('',*,*,#29531,.T.); -#40402=ORIENTED_EDGE('',*,*,#40386,.F.); -#40403=EDGE_LOOP('',(#40398,#40400,#40401,#40402)); -#40404=FACE_OUTER_BOUND('',#40403,.F.); -#40406=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.312499856949E0)); -#40407=DIRECTION('',(5.065474811863E-1,0.E0,8.622120674775E-1)); -#40408=DIRECTION('',(8.622120674775E-1,0.E0,-5.065474811863E-1)); -#40409=AXIS2_PLACEMENT_3D('',#40406,#40407,#40408); -#40410=PLANE('',#40409); -#40411=ORIENTED_EDGE('',*,*,#26820,.F.); -#40413=ORIENTED_EDGE('',*,*,#40412,.T.); -#40414=ORIENTED_EDGE('',*,*,#29533,.T.); -#40415=ORIENTED_EDGE('',*,*,#40399,.F.); -#40416=EDGE_LOOP('',(#40411,#40413,#40414,#40415)); -#40417=FACE_OUTER_BOUND('',#40416,.F.); -#40419=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.368749856949E0)); -#40420=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#40421=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#40422=AXIS2_PLACEMENT_3D('',#40419,#40420,#40421); -#40423=PLANE('',#40422); -#40424=ORIENTED_EDGE('',*,*,#26818,.F.); -#40426=ORIENTED_EDGE('',*,*,#40425,.T.); -#40427=ORIENTED_EDGE('',*,*,#29535,.T.); -#40428=ORIENTED_EDGE('',*,*,#40412,.F.); -#40429=EDGE_LOOP('',(#40424,#40426,#40427,#40428)); -#40430=FACE_OUTER_BOUND('',#40429,.F.); -#40432=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,5.462500143051E0)); -#40433=DIRECTION('',(9.752009016921E-1,0.E0,2.213214886517E-1)); -#40434=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#40435=AXIS2_PLACEMENT_3D('',#40432,#40433,#40434); -#40436=PLANE('',#40435); -#40437=ORIENTED_EDGE('',*,*,#26816,.F.); -#40439=ORIENTED_EDGE('',*,*,#40438,.T.); -#40440=ORIENTED_EDGE('',*,*,#29537,.T.); -#40441=ORIENTED_EDGE('',*,*,#40425,.F.); -#40442=EDGE_LOOP('',(#40437,#40439,#40440,#40441)); -#40443=FACE_OUTER_BOUND('',#40442,.F.); -#40445=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,5.55625E0)); -#40446=DIRECTION('',(9.752006830246E-1,0.E0,-2.213224521559E-1)); -#40447=DIRECTION('',(-2.213224521559E-1,0.E0,-9.752006830246E-1)); -#40448=AXIS2_PLACEMENT_3D('',#40445,#40446,#40447); -#40449=PLANE('',#40448); -#40450=ORIENTED_EDGE('',*,*,#26814,.F.); -#40452=ORIENTED_EDGE('',*,*,#40451,.T.); -#40453=ORIENTED_EDGE('',*,*,#29539,.T.); -#40454=ORIENTED_EDGE('',*,*,#40438,.F.); -#40455=EDGE_LOOP('',(#40450,#40452,#40453,#40454)); -#40456=FACE_OUTER_BOUND('',#40455,.F.); -#40458=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,5.6125E0)); -#40459=DIRECTION('',(7.975044865771E-1,0.E0,-6.033130148517E-1)); -#40460=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865771E-1)); -#40461=AXIS2_PLACEMENT_3D('',#40458,#40459,#40460); -#40462=PLANE('',#40461); -#40463=ORIENTED_EDGE('',*,*,#26812,.F.); -#40465=ORIENTED_EDGE('',*,*,#40464,.T.); -#40466=ORIENTED_EDGE('',*,*,#29541,.T.); -#40467=ORIENTED_EDGE('',*,*,#40451,.F.); -#40468=EDGE_LOOP('',(#40463,#40465,#40466,#40467)); -#40469=FACE_OUTER_BOUND('',#40468,.F.); -#40471=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,5.687500143051E0)); -#40472=DIRECTION('',(5.065496359537E-1,0.E0,-8.622108015533E-1)); -#40473=DIRECTION('',(-8.622108015533E-1,0.E0,-5.065496359537E-1)); -#40474=AXIS2_PLACEMENT_3D('',#40471,#40472,#40473); -#40475=PLANE('',#40474); -#40476=ORIENTED_EDGE('',*,*,#26810,.F.); -#40477=ORIENTED_EDGE('',*,*,#40258,.T.); -#40478=ORIENTED_EDGE('',*,*,#29543,.T.); -#40479=ORIENTED_EDGE('',*,*,#40464,.F.); -#40480=EDGE_LOOP('',(#40476,#40477,#40478,#40479)); -#40481=FACE_OUTER_BOUND('',#40480,.F.); -#40483=CARTESIAN_POINT('',(4.75E0,1.55E0,4.524999856949E0)); -#40484=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40485=DIRECTION('',(0.E0,0.E0,1.E0)); -#40486=AXIS2_PLACEMENT_3D('',#40483,#40484,#40485); -#40487=PLANE('',#40486); -#40488=ORIENTED_EDGE('',*,*,#25880,.F.); -#40490=ORIENTED_EDGE('',*,*,#40489,.T.); -#40491=ORIENTED_EDGE('',*,*,#29560,.T.); -#40493=ORIENTED_EDGE('',*,*,#40492,.F.); -#40494=EDGE_LOOP('',(#40488,#40490,#40491,#40493)); -#40495=FACE_OUTER_BOUND('',#40494,.F.); -#40497=CARTESIAN_POINT('',(5.75E0,1.55E0,4.225000143051E0)); -#40498=DIRECTION('',(-2.873476341569E-1,0.E0,-9.578263606440E-1)); -#40499=DIRECTION('',(-9.578263606440E-1,0.E0,2.873476341569E-1)); -#40500=AXIS2_PLACEMENT_3D('',#40497,#40498,#40499); -#40501=PLANE('',#40500); -#40502=ORIENTED_EDGE('',*,*,#25894,.F.); -#40504=ORIENTED_EDGE('',*,*,#40503,.T.); -#40505=ORIENTED_EDGE('',*,*,#29562,.T.); -#40506=ORIENTED_EDGE('',*,*,#40489,.F.); -#40507=EDGE_LOOP('',(#40502,#40504,#40505,#40506)); -#40508=FACE_OUTER_BOUND('',#40507,.F.); -#40510=CARTESIAN_POINT('',(5.75E0,1.55E0,4.337500143051E0)); -#40511=DIRECTION('',(1.E0,0.E0,0.E0)); -#40512=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40513=AXIS2_PLACEMENT_3D('',#40510,#40511,#40512); -#40514=PLANE('',#40513); -#40515=ORIENTED_EDGE('',*,*,#25892,.F.); -#40517=ORIENTED_EDGE('',*,*,#40516,.T.); -#40518=ORIENTED_EDGE('',*,*,#29564,.T.); -#40519=ORIENTED_EDGE('',*,*,#40503,.F.); -#40520=EDGE_LOOP('',(#40515,#40517,#40518,#40519)); -#40521=FACE_OUTER_BOUND('',#40520,.F.); -#40523=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.412499856949E0)); -#40524=DIRECTION('',(2.818406603838E-1,0.E0,9.594612249353E-1)); -#40525=DIRECTION('',(9.594612249353E-1,0.E0,-2.818406603838E-1)); -#40526=AXIS2_PLACEMENT_3D('',#40523,#40524,#40525); -#40527=PLANE('',#40526); -#40528=ORIENTED_EDGE('',*,*,#25890,.F.); -#40530=ORIENTED_EDGE('',*,*,#40529,.T.); -#40531=ORIENTED_EDGE('',*,*,#29566,.T.); -#40532=ORIENTED_EDGE('',*,*,#40516,.F.); -#40533=EDGE_LOOP('',(#40528,#40530,#40531,#40532)); -#40534=FACE_OUTER_BOUND('',#40533,.F.); -#40536=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,4.787500143051E0)); -#40537=DIRECTION('',(1.E0,0.E0,0.E0)); -#40538=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40539=AXIS2_PLACEMENT_3D('',#40536,#40537,#40538); -#40540=PLANE('',#40539); -#40541=ORIENTED_EDGE('',*,*,#25888,.F.); -#40543=ORIENTED_EDGE('',*,*,#40542,.T.); -#40544=ORIENTED_EDGE('',*,*,#29568,.T.); -#40545=ORIENTED_EDGE('',*,*,#40529,.F.); -#40546=EDGE_LOOP('',(#40541,#40543,#40544,#40545)); -#40547=FACE_OUTER_BOUND('',#40546,.F.); -#40549=CARTESIAN_POINT('',(5.75E0,1.55E0,4.862499856949E0)); -#40550=DIRECTION('',(2.818406603838E-1,0.E0,-9.594612249353E-1)); -#40551=DIRECTION('',(-9.594612249353E-1,0.E0,-2.818406603838E-1)); -#40552=AXIS2_PLACEMENT_3D('',#40549,#40550,#40551); -#40553=PLANE('',#40552); -#40554=ORIENTED_EDGE('',*,*,#25886,.F.); -#40556=ORIENTED_EDGE('',*,*,#40555,.T.); -#40557=ORIENTED_EDGE('',*,*,#29570,.T.); -#40558=ORIENTED_EDGE('',*,*,#40542,.F.); -#40559=EDGE_LOOP('',(#40554,#40556,#40557,#40558)); -#40560=FACE_OUTER_BOUND('',#40559,.F.); -#40562=CARTESIAN_POINT('',(5.75E0,1.55E0,4.974999856949E0)); -#40563=DIRECTION('',(1.E0,0.E0,0.E0)); -#40564=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40565=AXIS2_PLACEMENT_3D('',#40562,#40563,#40564); -#40566=PLANE('',#40565); -#40567=ORIENTED_EDGE('',*,*,#25884,.F.); -#40569=ORIENTED_EDGE('',*,*,#40568,.T.); -#40570=ORIENTED_EDGE('',*,*,#29572,.T.); -#40571=ORIENTED_EDGE('',*,*,#40555,.F.); -#40572=EDGE_LOOP('',(#40567,#40569,#40570,#40571)); -#40573=FACE_OUTER_BOUND('',#40572,.F.); -#40575=CARTESIAN_POINT('',(4.75E0,1.55E0,4.675000143051E0)); -#40576=DIRECTION('',(-2.873476341569E-1,0.E0,9.578263606440E-1)); -#40577=DIRECTION('',(9.578263606440E-1,0.E0,2.873476341569E-1)); -#40578=AXIS2_PLACEMENT_3D('',#40575,#40576,#40577); -#40579=PLANE('',#40578); -#40580=ORIENTED_EDGE('',*,*,#25882,.F.); -#40581=ORIENTED_EDGE('',*,*,#40492,.T.); -#40582=ORIENTED_EDGE('',*,*,#29574,.T.); -#40583=ORIENTED_EDGE('',*,*,#40568,.F.); -#40584=EDGE_LOOP('',(#40580,#40581,#40582,#40583)); -#40585=FACE_OUTER_BOUND('',#40584,.F.); -#40587=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,4.6E0)); -#40588=DIRECTION('',(2.818416400264E-1,0.E0,9.594609371659E-1)); -#40589=DIRECTION('',(9.594609371659E-1,0.E0,-2.818416400264E-1)); -#40590=AXIS2_PLACEMENT_3D('',#40587,#40588,#40589); -#40591=PLANE('',#40590); -#40592=ORIENTED_EDGE('',*,*,#26852,.F.); -#40594=ORIENTED_EDGE('',*,*,#40593,.T.); -#40595=ORIENTED_EDGE('',*,*,#29578,.T.); -#40597=ORIENTED_EDGE('',*,*,#40596,.F.); -#40598=EDGE_LOOP('',(#40592,#40594,#40595,#40597)); -#40599=FACE_OUTER_BOUND('',#40598,.F.); -#40601=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.76875E0)); -#40602=DIRECTION('',(2.818416400264E-1,0.E0,-9.594609371659E-1)); -#40603=DIRECTION('',(-9.594609371659E-1,0.E0,-2.818416400264E-1)); -#40604=AXIS2_PLACEMENT_3D('',#40601,#40602,#40603); -#40605=PLANE('',#40604); -#40606=ORIENTED_EDGE('',*,*,#26856,.F.); -#40608=ORIENTED_EDGE('',*,*,#40607,.T.); -#40609=ORIENTED_EDGE('',*,*,#29580,.T.); -#40610=ORIENTED_EDGE('',*,*,#40593,.F.); -#40611=EDGE_LOOP('',(#40606,#40608,#40609,#40610)); -#40612=FACE_OUTER_BOUND('',#40611,.F.); -#40614=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,4.43125E0)); -#40615=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40616=DIRECTION('',(0.E0,0.E0,1.E0)); -#40617=AXIS2_PLACEMENT_3D('',#40614,#40615,#40616); -#40618=PLANE('',#40617); -#40619=ORIENTED_EDGE('',*,*,#26854,.F.); -#40620=ORIENTED_EDGE('',*,*,#40596,.T.); -#40621=ORIENTED_EDGE('',*,*,#29582,.T.); -#40622=ORIENTED_EDGE('',*,*,#40607,.F.); -#40623=EDGE_LOOP('',(#40619,#40620,#40621,#40622)); -#40624=FACE_OUTER_BOUND('',#40623,.F.); -#40626=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,3.8125E0)); -#40627=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40628=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40629=AXIS2_PLACEMENT_3D('',#40626,#40627,#40628); -#40630=PLANE('',#40629); -#40631=ORIENTED_EDGE('',*,*,#25898,.F.); -#40633=ORIENTED_EDGE('',*,*,#40632,.T.); -#40634=ORIENTED_EDGE('',*,*,#29599,.T.); -#40636=ORIENTED_EDGE('',*,*,#40635,.F.); -#40637=EDGE_LOOP('',(#40631,#40633,#40634,#40636)); -#40638=FACE_OUTER_BOUND('',#40637,.F.); -#40640=CARTESIAN_POINT('',(5.388297885656E0,1.55E0,4.074999856949E0)); -#40641=DIRECTION('',(1.E0,0.E0,0.E0)); -#40642=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40643=AXIS2_PLACEMENT_3D('',#40640,#40641,#40642); -#40644=PLANE('',#40643); -#40645=ORIENTED_EDGE('',*,*,#25904,.F.); -#40647=ORIENTED_EDGE('',*,*,#40646,.T.); -#40648=ORIENTED_EDGE('',*,*,#29601,.T.); -#40649=ORIENTED_EDGE('',*,*,#40632,.F.); -#40650=EDGE_LOOP('',(#40645,#40647,#40648,#40649)); -#40651=FACE_OUTER_BOUND('',#40650,.F.); -#40653=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,4.074999856949E0)); -#40654=DIRECTION('',(0.E0,0.E0,1.E0)); -#40655=DIRECTION('',(1.E0,0.E0,0.E0)); -#40656=AXIS2_PLACEMENT_3D('',#40653,#40654,#40655); -#40657=PLANE('',#40656); -#40658=ORIENTED_EDGE('',*,*,#25902,.F.); -#40660=ORIENTED_EDGE('',*,*,#40659,.T.); -#40661=ORIENTED_EDGE('',*,*,#29603,.T.); -#40662=ORIENTED_EDGE('',*,*,#40646,.F.); -#40663=EDGE_LOOP('',(#40658,#40660,#40661,#40662)); -#40664=FACE_OUTER_BOUND('',#40663,.F.); -#40666=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,3.8125E0)); -#40667=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40668=DIRECTION('',(0.E0,0.E0,1.E0)); -#40669=AXIS2_PLACEMENT_3D('',#40666,#40667,#40668); -#40670=PLANE('',#40669); -#40671=ORIENTED_EDGE('',*,*,#25900,.F.); -#40672=ORIENTED_EDGE('',*,*,#40635,.T.); -#40673=ORIENTED_EDGE('',*,*,#29605,.T.); -#40674=ORIENTED_EDGE('',*,*,#40659,.F.); -#40675=EDGE_LOOP('',(#40671,#40672,#40673,#40674)); -#40676=FACE_OUTER_BOUND('',#40675,.F.); -#40678=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,3.08125E0)); -#40679=DIRECTION('',(8.697591154214E-1,0.E0,-4.934765254207E-1)); -#40680=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#40681=AXIS2_PLACEMENT_3D('',#40678,#40679,#40680); -#40682=PLANE('',#40681); -#40683=ORIENTED_EDGE('',*,*,#25908,.F.); -#40685=ORIENTED_EDGE('',*,*,#40684,.T.); -#40686=ORIENTED_EDGE('',*,*,#29622,.T.); -#40688=ORIENTED_EDGE('',*,*,#40687,.F.); -#40689=EDGE_LOOP('',(#40683,#40685,#40686,#40688)); -#40690=FACE_OUTER_BOUND('',#40689,.F.); -#40692=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,3.043749713898E0)); -#40693=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#40694=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#40695=AXIS2_PLACEMENT_3D('',#40692,#40693,#40694); -#40696=PLANE('',#40695); -#40697=ORIENTED_EDGE('',*,*,#25944,.F.); -#40699=ORIENTED_EDGE('',*,*,#40698,.T.); -#40700=ORIENTED_EDGE('',*,*,#29624,.T.); -#40701=ORIENTED_EDGE('',*,*,#40684,.F.); -#40702=EDGE_LOOP('',(#40697,#40699,#40700,#40701)); -#40703=FACE_OUTER_BOUND('',#40702,.F.); -#40705=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,2.987499713898E0)); -#40706=DIRECTION('',(-5.513869326687E-1,0.E0,-8.342496331927E-1)); -#40707=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#40708=AXIS2_PLACEMENT_3D('',#40705,#40706,#40707); -#40709=PLANE('',#40708); -#40710=ORIENTED_EDGE('',*,*,#25942,.F.); -#40712=ORIENTED_EDGE('',*,*,#40711,.T.); -#40713=ORIENTED_EDGE('',*,*,#29626,.T.); -#40714=ORIENTED_EDGE('',*,*,#40698,.F.); -#40715=EDGE_LOOP('',(#40710,#40712,#40713,#40714)); -#40716=FACE_OUTER_BOUND('',#40715,.F.); -#40718=CARTESIAN_POINT('',(5.409574478865E0,1.55E0,2.96875E0)); -#40719=DIRECTION('',(-2.818376003121E-1,0.E0,-9.594621238227E-1)); -#40720=DIRECTION('',(-9.594621238227E-1,0.E0,2.818376003121E-1)); -#40721=AXIS2_PLACEMENT_3D('',#40718,#40719,#40720); -#40722=PLANE('',#40721); -#40723=ORIENTED_EDGE('',*,*,#25940,.F.); -#40725=ORIENTED_EDGE('',*,*,#40724,.T.); -#40726=ORIENTED_EDGE('',*,*,#29628,.T.); -#40727=ORIENTED_EDGE('',*,*,#40711,.F.); -#40728=EDGE_LOOP('',(#40723,#40725,#40726,#40727)); -#40729=FACE_OUTER_BOUND('',#40728,.F.); -#40731=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,2.96875E0)); -#40732=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40733=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40734=AXIS2_PLACEMENT_3D('',#40731,#40732,#40733); -#40735=PLANE('',#40734); -#40736=ORIENTED_EDGE('',*,*,#25938,.F.); -#40738=ORIENTED_EDGE('',*,*,#40737,.T.); -#40739=ORIENTED_EDGE('',*,*,#29630,.T.); -#40740=ORIENTED_EDGE('',*,*,#40724,.F.); -#40741=EDGE_LOOP('',(#40736,#40738,#40739,#40740)); -#40742=FACE_OUTER_BOUND('',#40741,.F.); -#40744=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,2.987499713898E0)); -#40745=DIRECTION('',(2.818376608812E-1,0.E0,-9.594621060308E-1)); -#40746=DIRECTION('',(-9.594621060308E-1,0.E0,-2.818376608812E-1)); -#40747=AXIS2_PLACEMENT_3D('',#40744,#40745,#40746); -#40748=PLANE('',#40747); -#40749=ORIENTED_EDGE('',*,*,#25936,.F.); -#40751=ORIENTED_EDGE('',*,*,#40750,.T.); -#40752=ORIENTED_EDGE('',*,*,#29632,.T.); -#40753=ORIENTED_EDGE('',*,*,#40737,.F.); -#40754=EDGE_LOOP('',(#40749,#40751,#40752,#40753)); -#40755=FACE_OUTER_BOUND('',#40754,.F.); -#40757=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,3.043749713898E0)); -#40758=DIRECTION('',(5.513868990736E-1,0.E0,-8.342496553970E-1)); -#40759=DIRECTION('',(-8.342496553970E-1,0.E0,-5.513868990736E-1)); -#40760=AXIS2_PLACEMENT_3D('',#40757,#40758,#40759); -#40761=PLANE('',#40760); -#40762=ORIENTED_EDGE('',*,*,#25934,.F.); -#40764=ORIENTED_EDGE('',*,*,#40763,.T.); -#40765=ORIENTED_EDGE('',*,*,#29634,.T.); -#40766=ORIENTED_EDGE('',*,*,#40750,.F.); -#40767=EDGE_LOOP('',(#40762,#40764,#40765,#40766)); -#40768=FACE_OUTER_BOUND('',#40767,.F.); -#40770=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,3.118750286102E0)); -#40771=DIRECTION('',(7.615418403799E-1,0.E0,-6.481157499635E-1)); -#40772=DIRECTION('',(-6.481157499635E-1,0.E0,-7.615418403799E-1)); -#40773=AXIS2_PLACEMENT_3D('',#40770,#40771,#40772); -#40774=PLANE('',#40773); -#40775=ORIENTED_EDGE('',*,*,#25932,.F.); -#40777=ORIENTED_EDGE('',*,*,#40776,.T.); -#40778=ORIENTED_EDGE('',*,*,#29636,.T.); -#40779=ORIENTED_EDGE('',*,*,#40763,.F.); -#40780=EDGE_LOOP('',(#40775,#40777,#40778,#40779)); -#40781=FACE_OUTER_BOUND('',#40780,.F.); -#40783=CARTESIAN_POINT('',(5.75E0,1.55E0,3.212499713898E0)); -#40784=DIRECTION('',(9.752004601724E-1,0.E0,-2.213234340948E-1)); -#40785=DIRECTION('',(-2.213234340948E-1,0.E0,-9.752004601724E-1)); -#40786=AXIS2_PLACEMENT_3D('',#40783,#40784,#40785); -#40787=PLANE('',#40786); -#40788=ORIENTED_EDGE('',*,*,#25930,.F.); -#40790=ORIENTED_EDGE('',*,*,#40789,.T.); -#40791=ORIENTED_EDGE('',*,*,#29638,.T.); -#40792=ORIENTED_EDGE('',*,*,#40776,.F.); -#40793=EDGE_LOOP('',(#40788,#40790,#40791,#40792)); -#40794=FACE_OUTER_BOUND('',#40793,.F.); -#40796=CARTESIAN_POINT('',(5.75E0,1.55E0,3.662500143051E0)); -#40797=DIRECTION('',(1.E0,0.E0,0.E0)); -#40798=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40799=AXIS2_PLACEMENT_3D('',#40796,#40797,#40798); -#40800=PLANE('',#40799); -#40801=ORIENTED_EDGE('',*,*,#25928,.F.); -#40803=ORIENTED_EDGE('',*,*,#40802,.T.); -#40804=ORIENTED_EDGE('',*,*,#29640,.T.); -#40805=ORIENTED_EDGE('',*,*,#40789,.F.); -#40806=EDGE_LOOP('',(#40801,#40803,#40804,#40805)); -#40807=FACE_OUTER_BOUND('',#40806,.F.); -#40809=CARTESIAN_POINT('',(4.75E0,1.55E0,3.662500143051E0)); -#40810=DIRECTION('',(0.E0,0.E0,1.E0)); -#40811=DIRECTION('',(1.E0,0.E0,0.E0)); -#40812=AXIS2_PLACEMENT_3D('',#40809,#40810,#40811); -#40813=PLANE('',#40812); -#40814=ORIENTED_EDGE('',*,*,#25926,.F.); -#40816=ORIENTED_EDGE('',*,*,#40815,.T.); -#40817=ORIENTED_EDGE('',*,*,#29642,.T.); -#40818=ORIENTED_EDGE('',*,*,#40802,.F.); -#40819=EDGE_LOOP('',(#40814,#40816,#40817,#40818)); -#40820=FACE_OUTER_BOUND('',#40819,.F.); -#40822=CARTESIAN_POINT('',(4.75E0,1.55E0,3.212499713898E0)); -#40823=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40824=DIRECTION('',(0.E0,0.E0,1.E0)); -#40825=AXIS2_PLACEMENT_3D('',#40822,#40823,#40824); -#40826=PLANE('',#40825); -#40827=ORIENTED_EDGE('',*,*,#25924,.F.); -#40829=ORIENTED_EDGE('',*,*,#40828,.T.); -#40830=ORIENTED_EDGE('',*,*,#29644,.T.); -#40831=ORIENTED_EDGE('',*,*,#40815,.F.); -#40832=EDGE_LOOP('',(#40827,#40829,#40830,#40831)); -#40833=FACE_OUTER_BOUND('',#40832,.F.); -#40835=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,3.118750286102E0)); -#40836=DIRECTION('',(-9.752004643543E-1,0.E0,-2.213234156683E-1)); -#40837=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#40838=AXIS2_PLACEMENT_3D('',#40835,#40836,#40837); -#40839=PLANE('',#40838); -#40840=ORIENTED_EDGE('',*,*,#25922,.F.); -#40842=ORIENTED_EDGE('',*,*,#40841,.T.); -#40843=ORIENTED_EDGE('',*,*,#29646,.T.); -#40844=ORIENTED_EDGE('',*,*,#40828,.F.); -#40845=EDGE_LOOP('',(#40840,#40842,#40843,#40844)); -#40846=FACE_OUTER_BOUND('',#40845,.F.); -#40848=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,3.043749713898E0)); -#40849=DIRECTION('',(-7.615418683844E-1,0.E0,-6.481157170580E-1)); -#40850=DIRECTION('',(-6.481157170580E-1,0.E0,7.615418683844E-1)); -#40851=AXIS2_PLACEMENT_3D('',#40848,#40849,#40850); -#40852=PLANE('',#40851); -#40853=ORIENTED_EDGE('',*,*,#25920,.F.); -#40855=ORIENTED_EDGE('',*,*,#40854,.T.); -#40856=ORIENTED_EDGE('',*,*,#29648,.T.); -#40857=ORIENTED_EDGE('',*,*,#40841,.F.); -#40858=EDGE_LOOP('',(#40853,#40855,#40856,#40857)); -#40859=FACE_OUTER_BOUND('',#40858,.F.); -#40861=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,2.987499713898E0)); -#40862=DIRECTION('',(-5.513869326687E-1,0.E0,-8.342496331927E-1)); -#40863=DIRECTION('',(-8.342496331927E-1,0.E0,5.513869326687E-1)); -#40864=AXIS2_PLACEMENT_3D('',#40861,#40862,#40863); -#40865=PLANE('',#40864); -#40866=ORIENTED_EDGE('',*,*,#25918,.F.); -#40868=ORIENTED_EDGE('',*,*,#40867,.T.); -#40869=ORIENTED_EDGE('',*,*,#29650,.T.); -#40870=ORIENTED_EDGE('',*,*,#40854,.F.); -#40871=EDGE_LOOP('',(#40866,#40868,#40869,#40870)); -#40872=FACE_OUTER_BOUND('',#40871,.F.); -#40874=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.96875E0)); -#40875=DIRECTION('',(-2.818377214504E-1,0.E0,-9.594620882388E-1)); -#40876=DIRECTION('',(-9.594620882388E-1,0.E0,2.818377214504E-1)); -#40877=AXIS2_PLACEMENT_3D('',#40874,#40875,#40876); -#40878=PLANE('',#40877); -#40879=ORIENTED_EDGE('',*,*,#25916,.F.); -#40881=ORIENTED_EDGE('',*,*,#40880,.T.); -#40882=ORIENTED_EDGE('',*,*,#29652,.T.); -#40883=ORIENTED_EDGE('',*,*,#40867,.F.); -#40884=EDGE_LOOP('',(#40879,#40881,#40882,#40883)); -#40885=FACE_OUTER_BOUND('',#40884,.F.); -#40887=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,2.96875E0)); -#40888=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40889=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40890=AXIS2_PLACEMENT_3D('',#40887,#40888,#40889); -#40891=PLANE('',#40890); -#40892=ORIENTED_EDGE('',*,*,#25914,.F.); -#40894=ORIENTED_EDGE('',*,*,#40893,.T.); -#40895=ORIENTED_EDGE('',*,*,#29654,.T.); -#40896=ORIENTED_EDGE('',*,*,#40880,.F.); -#40897=EDGE_LOOP('',(#40892,#40894,#40895,#40896)); -#40898=FACE_OUTER_BOUND('',#40897,.F.); -#40900=CARTESIAN_POINT('',(5.132978737354E0,1.55E0,2.987499713898E0)); -#40901=DIRECTION('',(2.818377214504E-1,0.E0,-9.594620882388E-1)); -#40902=DIRECTION('',(-9.594620882388E-1,0.E0,-2.818377214504E-1)); -#40903=AXIS2_PLACEMENT_3D('',#40900,#40901,#40902); -#40904=PLANE('',#40903); -#40905=ORIENTED_EDGE('',*,*,#25912,.F.); -#40907=ORIENTED_EDGE('',*,*,#40906,.T.); -#40908=ORIENTED_EDGE('',*,*,#29656,.T.); -#40909=ORIENTED_EDGE('',*,*,#40893,.F.); -#40910=EDGE_LOOP('',(#40905,#40907,#40908,#40909)); -#40911=FACE_OUTER_BOUND('',#40910,.F.); -#40913=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,3.043749713898E0)); -#40914=DIRECTION('',(5.513869326687E-1,0.E0,-8.342496331927E-1)); -#40915=DIRECTION('',(-8.342496331927E-1,0.E0,-5.513869326687E-1)); -#40916=AXIS2_PLACEMENT_3D('',#40913,#40914,#40915); -#40917=PLANE('',#40916); -#40918=ORIENTED_EDGE('',*,*,#25910,.F.); -#40919=ORIENTED_EDGE('',*,*,#40687,.T.); -#40920=ORIENTED_EDGE('',*,*,#29658,.T.); -#40921=ORIENTED_EDGE('',*,*,#40906,.F.); -#40922=EDGE_LOOP('',(#40918,#40919,#40920,#40921)); -#40923=FACE_OUTER_BOUND('',#40922,.F.); -#40925=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.550000143051E0)); -#40926=DIRECTION('',(1.E0,0.E0,0.E0)); -#40927=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40928=AXIS2_PLACEMENT_3D('',#40925,#40926,#40927); -#40929=PLANE('',#40928); -#40930=ORIENTED_EDGE('',*,*,#26866,.F.); -#40932=ORIENTED_EDGE('',*,*,#40931,.T.); -#40933=ORIENTED_EDGE('',*,*,#29662,.T.); -#40935=ORIENTED_EDGE('',*,*,#40934,.F.); -#40936=EDGE_LOOP('',(#40930,#40932,#40933,#40935)); -#40937=FACE_OUTER_BOUND('',#40936,.F.); -#40939=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.550000143051E0)); -#40940=DIRECTION('',(0.E0,0.E0,-1.E0)); -#40941=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40942=AXIS2_PLACEMENT_3D('',#40939,#40940,#40941); -#40943=PLANE('',#40942); -#40944=ORIENTED_EDGE('',*,*,#26884,.F.); -#40946=ORIENTED_EDGE('',*,*,#40945,.T.); -#40947=ORIENTED_EDGE('',*,*,#29664,.T.); -#40948=ORIENTED_EDGE('',*,*,#40931,.F.); -#40949=EDGE_LOOP('',(#40944,#40946,#40947,#40948)); -#40950=FACE_OUTER_BOUND('',#40949,.F.); -#40952=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,3.19375E0)); -#40953=DIRECTION('',(-1.E0,0.E0,0.E0)); -#40954=DIRECTION('',(0.E0,0.E0,1.E0)); -#40955=AXIS2_PLACEMENT_3D('',#40952,#40953,#40954); -#40956=PLANE('',#40955); -#40957=ORIENTED_EDGE('',*,*,#26882,.F.); -#40959=ORIENTED_EDGE('',*,*,#40958,.T.); -#40960=ORIENTED_EDGE('',*,*,#29666,.T.); -#40961=ORIENTED_EDGE('',*,*,#40945,.F.); -#40962=EDGE_LOOP('',(#40957,#40959,#40960,#40961)); -#40963=FACE_OUTER_BOUND('',#40962,.F.); -#40965=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,3.1375E0)); -#40966=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#40967=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#40968=AXIS2_PLACEMENT_3D('',#40965,#40966,#40967); -#40969=PLANE('',#40968); -#40970=ORIENTED_EDGE('',*,*,#26880,.F.); -#40972=ORIENTED_EDGE('',*,*,#40971,.T.); -#40973=ORIENTED_EDGE('',*,*,#29668,.T.); -#40974=ORIENTED_EDGE('',*,*,#40958,.F.); -#40975=EDGE_LOOP('',(#40970,#40972,#40973,#40974)); -#40976=FACE_OUTER_BOUND('',#40975,.F.); -#40978=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,3.099999713898E0)); -#40979=DIRECTION('',(-6.611591372532E-1,0.E0,7.502456899087E-1)); -#40980=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#40981=AXIS2_PLACEMENT_3D('',#40978,#40979,#40980); -#40982=PLANE('',#40981); -#40983=ORIENTED_EDGE('',*,*,#26878,.F.); -#40985=ORIENTED_EDGE('',*,*,#40984,.T.); -#40986=ORIENTED_EDGE('',*,*,#29670,.T.); -#40987=ORIENTED_EDGE('',*,*,#40971,.F.); -#40988=EDGE_LOOP('',(#40983,#40985,#40986,#40987)); -#40989=FACE_OUTER_BOUND('',#40988,.F.); -#40991=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,3.08125E0)); -#40992=DIRECTION('',(-2.818377214504E-1,0.E0,9.594620882388E-1)); -#40993=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#40994=AXIS2_PLACEMENT_3D('',#40991,#40992,#40993); -#40995=PLANE('',#40994); -#40996=ORIENTED_EDGE('',*,*,#26876,.F.); -#40998=ORIENTED_EDGE('',*,*,#40997,.T.); -#40999=ORIENTED_EDGE('',*,*,#29672,.T.); -#41000=ORIENTED_EDGE('',*,*,#40984,.F.); -#41001=EDGE_LOOP('',(#40996,#40998,#40999,#41000)); -#41002=FACE_OUTER_BOUND('',#41001,.F.); -#41004=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,3.08125E0)); -#41005=DIRECTION('',(0.E0,0.E0,1.E0)); -#41006=DIRECTION('',(1.E0,0.E0,0.E0)); -#41007=AXIS2_PLACEMENT_3D('',#41004,#41005,#41006); -#41008=PLANE('',#41007); -#41009=ORIENTED_EDGE('',*,*,#26874,.F.); -#41011=ORIENTED_EDGE('',*,*,#41010,.T.); -#41012=ORIENTED_EDGE('',*,*,#29674,.T.); -#41013=ORIENTED_EDGE('',*,*,#40997,.F.); -#41014=EDGE_LOOP('',(#41009,#41011,#41012,#41013)); -#41015=FACE_OUTER_BOUND('',#41014,.F.); -#41017=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,3.099999713898E0)); -#41018=DIRECTION('',(2.818374791740E-1,0.E0,9.594621594064E-1)); -#41019=DIRECTION('',(9.594621594064E-1,0.E0,-2.818374791740E-1)); -#41020=AXIS2_PLACEMENT_3D('',#41017,#41018,#41019); -#41021=PLANE('',#41020); -#41022=ORIENTED_EDGE('',*,*,#26872,.F.); -#41024=ORIENTED_EDGE('',*,*,#41023,.T.); -#41025=ORIENTED_EDGE('',*,*,#29676,.T.); -#41026=ORIENTED_EDGE('',*,*,#41010,.F.); -#41027=EDGE_LOOP('',(#41022,#41024,#41025,#41026)); -#41028=FACE_OUTER_BOUND('',#41027,.F.); -#41030=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,3.1375E0)); -#41031=DIRECTION('',(6.611591372532E-1,0.E0,7.502456899087E-1)); -#41032=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#41033=AXIS2_PLACEMENT_3D('',#41030,#41031,#41032); -#41034=PLANE('',#41033); -#41035=ORIENTED_EDGE('',*,*,#26870,.F.); -#41037=ORIENTED_EDGE('',*,*,#41036,.T.); -#41038=ORIENTED_EDGE('',*,*,#29678,.T.); -#41039=ORIENTED_EDGE('',*,*,#41023,.F.); -#41040=EDGE_LOOP('',(#41035,#41037,#41038,#41039)); -#41041=FACE_OUTER_BOUND('',#41040,.F.); -#41043=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,3.19375E0)); -#41044=DIRECTION('',(9.353258264754E-1,0.E0,3.537875044826E-1)); -#41045=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#41046=AXIS2_PLACEMENT_3D('',#41043,#41044,#41045); -#41047=PLANE('',#41046); -#41048=ORIENTED_EDGE('',*,*,#26868,.F.); -#41049=ORIENTED_EDGE('',*,*,#40934,.T.); -#41050=ORIENTED_EDGE('',*,*,#29680,.T.); -#41051=ORIENTED_EDGE('',*,*,#41036,.F.); -#41052=EDGE_LOOP('',(#41048,#41049,#41050,#41051)); -#41053=FACE_OUTER_BOUND('',#41052,.F.); -#41055=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,3.08125E0)); -#41056=DIRECTION('',(0.E0,0.E0,1.E0)); -#41057=DIRECTION('',(1.E0,0.E0,0.E0)); -#41058=AXIS2_PLACEMENT_3D('',#41055,#41056,#41057); -#41059=PLANE('',#41058); -#41060=ORIENTED_EDGE('',*,*,#26894,.F.); -#41062=ORIENTED_EDGE('',*,*,#41061,.T.); -#41063=ORIENTED_EDGE('',*,*,#29684,.T.); -#41065=ORIENTED_EDGE('',*,*,#41064,.F.); -#41066=EDGE_LOOP('',(#41060,#41062,#41063,#41065)); -#41067=FACE_OUTER_BOUND('',#41066,.F.); -#41069=CARTESIAN_POINT('',(5.367021262646E0,1.55E0,3.099999713898E0)); -#41070=DIRECTION('',(2.818376003121E-1,0.E0,9.594621238227E-1)); -#41071=DIRECTION('',(9.594621238227E-1,0.E0,-2.818376003121E-1)); -#41072=AXIS2_PLACEMENT_3D('',#41069,#41070,#41071); -#41073=PLANE('',#41072); -#41074=ORIENTED_EDGE('',*,*,#26912,.F.); -#41076=ORIENTED_EDGE('',*,*,#41075,.T.); -#41077=ORIENTED_EDGE('',*,*,#29686,.T.); -#41078=ORIENTED_EDGE('',*,*,#41061,.F.); -#41079=EDGE_LOOP('',(#41074,#41076,#41077,#41078)); -#41080=FACE_OUTER_BOUND('',#41079,.F.); -#41082=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,3.1375E0)); -#41083=DIRECTION('',(6.611591372532E-1,0.E0,7.502456899087E-1)); -#41084=DIRECTION('',(7.502456899087E-1,0.E0,-6.611591372532E-1)); -#41085=AXIS2_PLACEMENT_3D('',#41082,#41083,#41084); -#41086=PLANE('',#41085); -#41087=ORIENTED_EDGE('',*,*,#26910,.F.); -#41089=ORIENTED_EDGE('',*,*,#41088,.T.); -#41090=ORIENTED_EDGE('',*,*,#29688,.T.); -#41091=ORIENTED_EDGE('',*,*,#41075,.F.); -#41092=EDGE_LOOP('',(#41087,#41089,#41090,#41091)); -#41093=FACE_OUTER_BOUND('',#41092,.F.); -#41095=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.19375E0)); -#41096=DIRECTION('',(9.353258264754E-1,0.E0,3.537875044826E-1)); -#41097=DIRECTION('',(3.537875044826E-1,0.E0,-9.353258264754E-1)); -#41098=AXIS2_PLACEMENT_3D('',#41095,#41096,#41097); -#41099=PLANE('',#41098); -#41100=ORIENTED_EDGE('',*,*,#26908,.F.); -#41102=ORIENTED_EDGE('',*,*,#41101,.T.); -#41103=ORIENTED_EDGE('',*,*,#29690,.T.); -#41104=ORIENTED_EDGE('',*,*,#41088,.F.); -#41105=EDGE_LOOP('',(#41100,#41102,#41103,#41104)); -#41106=FACE_OUTER_BOUND('',#41105,.F.); -#41108=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,3.550000143051E0)); -#41109=DIRECTION('',(1.E0,0.E0,0.E0)); -#41110=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41111=AXIS2_PLACEMENT_3D('',#41108,#41109,#41110); -#41112=PLANE('',#41111); -#41113=ORIENTED_EDGE('',*,*,#26906,.F.); -#41115=ORIENTED_EDGE('',*,*,#41114,.T.); -#41116=ORIENTED_EDGE('',*,*,#29692,.T.); -#41117=ORIENTED_EDGE('',*,*,#41101,.F.); -#41118=EDGE_LOOP('',(#41113,#41115,#41116,#41117)); -#41119=FACE_OUTER_BOUND('',#41118,.F.); -#41121=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.550000143051E0)); -#41122=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41123=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41124=AXIS2_PLACEMENT_3D('',#41121,#41122,#41123); -#41125=PLANE('',#41124); -#41126=ORIENTED_EDGE('',*,*,#26904,.F.); -#41128=ORIENTED_EDGE('',*,*,#41127,.T.); -#41129=ORIENTED_EDGE('',*,*,#29694,.T.); -#41130=ORIENTED_EDGE('',*,*,#41114,.F.); -#41131=EDGE_LOOP('',(#41126,#41128,#41129,#41130)); -#41132=FACE_OUTER_BOUND('',#41131,.F.); -#41134=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,3.19375E0)); -#41135=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41136=DIRECTION('',(0.E0,0.E0,1.E0)); -#41137=AXIS2_PLACEMENT_3D('',#41134,#41135,#41136); -#41138=PLANE('',#41137); -#41139=ORIENTED_EDGE('',*,*,#26902,.F.); -#41141=ORIENTED_EDGE('',*,*,#41140,.T.); -#41142=ORIENTED_EDGE('',*,*,#29696,.T.); -#41143=ORIENTED_EDGE('',*,*,#41127,.F.); -#41144=EDGE_LOOP('',(#41139,#41141,#41142,#41143)); -#41145=FACE_OUTER_BOUND('',#41144,.F.); -#41147=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,3.1375E0)); -#41148=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#41149=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#41150=AXIS2_PLACEMENT_3D('',#41147,#41148,#41149); -#41151=PLANE('',#41150); -#41152=ORIENTED_EDGE('',*,*,#26900,.F.); -#41154=ORIENTED_EDGE('',*,*,#41153,.T.); -#41155=ORIENTED_EDGE('',*,*,#29698,.T.); -#41156=ORIENTED_EDGE('',*,*,#41140,.F.); -#41157=EDGE_LOOP('',(#41152,#41154,#41155,#41156)); -#41158=FACE_OUTER_BOUND('',#41157,.F.); -#41160=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,3.099999713898E0)); -#41161=DIRECTION('',(-6.611590069362E-1,0.E0,7.502458047514E-1)); -#41162=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#41163=AXIS2_PLACEMENT_3D('',#41160,#41161,#41162); -#41164=PLANE('',#41163); -#41165=ORIENTED_EDGE('',*,*,#26898,.F.); -#41167=ORIENTED_EDGE('',*,*,#41166,.T.); -#41168=ORIENTED_EDGE('',*,*,#29700,.T.); -#41169=ORIENTED_EDGE('',*,*,#41153,.F.); -#41170=EDGE_LOOP('',(#41165,#41167,#41168,#41169)); -#41171=FACE_OUTER_BOUND('',#41170,.F.); -#41173=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,3.08125E0)); -#41174=DIRECTION('',(-2.818377214504E-1,0.E0,9.594620882388E-1)); -#41175=DIRECTION('',(9.594620882388E-1,0.E0,2.818377214504E-1)); -#41176=AXIS2_PLACEMENT_3D('',#41173,#41174,#41175); -#41177=PLANE('',#41176); -#41178=ORIENTED_EDGE('',*,*,#26896,.F.); -#41179=ORIENTED_EDGE('',*,*,#41064,.T.); -#41180=ORIENTED_EDGE('',*,*,#29702,.T.); -#41181=ORIENTED_EDGE('',*,*,#41166,.F.); -#41182=EDGE_LOOP('',(#41178,#41179,#41180,#41181)); -#41183=FACE_OUTER_BOUND('',#41182,.F.); -#41185=CARTESIAN_POINT('',(4.75E0,1.55E0,2.106250286102E0)); -#41186=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41187=DIRECTION('',(0.E0,0.E0,1.E0)); -#41188=AXIS2_PLACEMENT_3D('',#41185,#41186,#41187); -#41189=PLANE('',#41188); -#41190=ORIENTED_EDGE('',*,*,#25948,.F.); -#41192=ORIENTED_EDGE('',*,*,#41191,.T.); -#41193=ORIENTED_EDGE('',*,*,#29719,.T.); -#41195=ORIENTED_EDGE('',*,*,#41194,.F.); -#41196=EDGE_LOOP('',(#41190,#41192,#41193,#41195)); -#41197=FACE_OUTER_BOUND('',#41196,.F.); -#41199=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.106250286102E0)); -#41200=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41201=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41202=AXIS2_PLACEMENT_3D('',#41199,#41200,#41201); -#41203=PLANE('',#41202); -#41204=ORIENTED_EDGE('',*,*,#25962,.F.); -#41206=ORIENTED_EDGE('',*,*,#41205,.T.); -#41207=ORIENTED_EDGE('',*,*,#29721,.T.); -#41208=ORIENTED_EDGE('',*,*,#41191,.F.); -#41209=EDGE_LOOP('',(#41204,#41206,#41207,#41208)); -#41210=FACE_OUTER_BOUND('',#41209,.F.); -#41212=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.40625E0)); -#41213=DIRECTION('',(1.E0,0.E0,0.E0)); -#41214=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41215=AXIS2_PLACEMENT_3D('',#41212,#41213,#41214); -#41216=PLANE('',#41215); -#41217=ORIENTED_EDGE('',*,*,#25960,.F.); -#41219=ORIENTED_EDGE('',*,*,#41218,.T.); -#41220=ORIENTED_EDGE('',*,*,#29723,.T.); -#41221=ORIENTED_EDGE('',*,*,#41205,.F.); -#41222=EDGE_LOOP('',(#41217,#41219,#41220,#41221)); -#41223=FACE_OUTER_BOUND('',#41222,.F.); -#41225=CARTESIAN_POINT('',(5.75E0,1.55E0,2.40625E0)); -#41226=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41227=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41228=AXIS2_PLACEMENT_3D('',#41225,#41226,#41227); -#41229=PLANE('',#41228); -#41230=ORIENTED_EDGE('',*,*,#25958,.F.); -#41232=ORIENTED_EDGE('',*,*,#41231,.T.); -#41233=ORIENTED_EDGE('',*,*,#29725,.T.); -#41234=ORIENTED_EDGE('',*,*,#41218,.F.); -#41235=EDGE_LOOP('',(#41230,#41232,#41233,#41234)); -#41236=FACE_OUTER_BOUND('',#41235,.F.); -#41238=CARTESIAN_POINT('',(5.75E0,1.55E0,2.51875E0)); -#41239=DIRECTION('',(1.E0,0.E0,0.E0)); -#41240=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41241=AXIS2_PLACEMENT_3D('',#41238,#41239,#41240); -#41242=PLANE('',#41241); -#41243=ORIENTED_EDGE('',*,*,#25956,.F.); -#41245=ORIENTED_EDGE('',*,*,#41244,.T.); -#41246=ORIENTED_EDGE('',*,*,#29727,.T.); -#41247=ORIENTED_EDGE('',*,*,#41231,.F.); -#41248=EDGE_LOOP('',(#41243,#41245,#41246,#41247)); -#41249=FACE_OUTER_BOUND('',#41248,.F.); -#41251=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.51875E0)); -#41252=DIRECTION('',(0.E0,0.E0,1.E0)); -#41253=DIRECTION('',(1.E0,0.E0,0.E0)); -#41254=AXIS2_PLACEMENT_3D('',#41251,#41252,#41253); -#41255=PLANE('',#41254); -#41256=ORIENTED_EDGE('',*,*,#25954,.F.); -#41258=ORIENTED_EDGE('',*,*,#41257,.T.); -#41259=ORIENTED_EDGE('',*,*,#29729,.T.); -#41260=ORIENTED_EDGE('',*,*,#41244,.F.); -#41261=EDGE_LOOP('',(#41256,#41258,#41259,#41260)); -#41262=FACE_OUTER_BOUND('',#41261,.F.); -#41264=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,2.818749713898E0)); -#41265=DIRECTION('',(1.E0,0.E0,0.E0)); -#41266=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41267=AXIS2_PLACEMENT_3D('',#41264,#41265,#41266); -#41268=PLANE('',#41267); -#41269=ORIENTED_EDGE('',*,*,#25952,.F.); -#41271=ORIENTED_EDGE('',*,*,#41270,.T.); -#41272=ORIENTED_EDGE('',*,*,#29731,.T.); -#41273=ORIENTED_EDGE('',*,*,#41257,.F.); -#41274=EDGE_LOOP('',(#41269,#41271,#41272,#41273)); -#41275=FACE_OUTER_BOUND('',#41274,.F.); -#41277=CARTESIAN_POINT('',(4.75E0,1.55E0,2.818749713898E0)); -#41278=DIRECTION('',(0.E0,0.E0,1.E0)); -#41279=DIRECTION('',(1.E0,0.E0,0.E0)); -#41280=AXIS2_PLACEMENT_3D('',#41277,#41278,#41279); -#41281=PLANE('',#41280); -#41282=ORIENTED_EDGE('',*,*,#25950,.F.); -#41283=ORIENTED_EDGE('',*,*,#41194,.T.); -#41284=ORIENTED_EDGE('',*,*,#29733,.T.); -#41285=ORIENTED_EDGE('',*,*,#41270,.F.); -#41286=EDGE_LOOP('',(#41282,#41283,#41284,#41285)); -#41287=FACE_OUTER_BOUND('',#41286,.F.); -#41289=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.806249713898E0)); -#41290=DIRECTION('',(-8.697591154214E-1,0.E0,4.934765254208E-1)); -#41291=DIRECTION('',(4.934765254208E-1,0.E0,8.697591154214E-1)); -#41292=AXIS2_PLACEMENT_3D('',#41289,#41290,#41291); -#41293=PLANE('',#41292); -#41294=ORIENTED_EDGE('',*,*,#25966,.F.); -#41296=ORIENTED_EDGE('',*,*,#41295,.T.); -#41297=ORIENTED_EDGE('',*,*,#29750,.T.); -#41299=ORIENTED_EDGE('',*,*,#41298,.F.); -#41300=EDGE_LOOP('',(#41294,#41296,#41297,#41299)); -#41301=FACE_OUTER_BOUND('',#41300,.F.); -#41303=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.84375E0)); -#41304=DIRECTION('',(8.697591154214E-1,0.E0,4.934765254208E-1)); -#41305=DIRECTION('',(4.934765254208E-1,0.E0,-8.697591154214E-1)); -#41306=AXIS2_PLACEMENT_3D('',#41303,#41304,#41305); -#41307=PLANE('',#41306); -#41308=ORIENTED_EDGE('',*,*,#26032,.F.); -#41310=ORIENTED_EDGE('',*,*,#41309,.T.); -#41311=ORIENTED_EDGE('',*,*,#29752,.T.); -#41312=ORIENTED_EDGE('',*,*,#41295,.F.); -#41313=EDGE_LOOP('',(#41308,#41310,#41311,#41312)); -#41314=FACE_OUTER_BOUND('',#41313,.F.); -#41316=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.9E0)); -#41317=DIRECTION('',(6.611562980142E-1,0.E0,7.502481919980E-1)); -#41318=DIRECTION('',(7.502481919980E-1,0.E0,-6.611562980142E-1)); -#41319=AXIS2_PLACEMENT_3D('',#41316,#41317,#41318); -#41320=PLANE('',#41319); -#41321=ORIENTED_EDGE('',*,*,#26030,.F.); -#41323=ORIENTED_EDGE('',*,*,#41322,.T.); -#41324=ORIENTED_EDGE('',*,*,#29754,.T.); -#41325=ORIENTED_EDGE('',*,*,#41309,.F.); -#41326=EDGE_LOOP('',(#41321,#41323,#41324,#41325)); -#41327=FACE_OUTER_BOUND('',#41326,.F.); -#41329=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.937500286102E0)); -#41330=DIRECTION('',(4.032203477633E-1,0.E0,9.151029183374E-1)); -#41331=DIRECTION('',(9.151029183374E-1,0.E0,-4.032203477633E-1)); -#41332=AXIS2_PLACEMENT_3D('',#41329,#41330,#41331); -#41333=PLANE('',#41332); -#41334=ORIENTED_EDGE('',*,*,#26028,.F.); -#41336=ORIENTED_EDGE('',*,*,#41335,.T.); -#41337=ORIENTED_EDGE('',*,*,#29756,.T.); -#41338=ORIENTED_EDGE('',*,*,#41322,.F.); -#41339=EDGE_LOOP('',(#41334,#41336,#41337,#41338)); -#41340=FACE_OUTER_BOUND('',#41339,.F.); -#41342=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.937500286102E0)); -#41343=DIRECTION('',(0.E0,0.E0,1.E0)); -#41344=DIRECTION('',(1.E0,0.E0,0.E0)); -#41345=AXIS2_PLACEMENT_3D('',#41342,#41343,#41344); -#41346=PLANE('',#41345); -#41347=ORIENTED_EDGE('',*,*,#26026,.F.); -#41349=ORIENTED_EDGE('',*,*,#41348,.T.); -#41350=ORIENTED_EDGE('',*,*,#29758,.T.); -#41351=ORIENTED_EDGE('',*,*,#41335,.F.); -#41352=EDGE_LOOP('',(#41347,#41349,#41350,#41351)); -#41353=FACE_OUTER_BOUND('',#41352,.F.); -#41355=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.9E0)); -#41356=DIRECTION('',(-3.324522241845E-1,0.E0,9.431200976730E-1)); -#41357=DIRECTION('',(9.431200976730E-1,0.E0,3.324522241845E-1)); -#41358=AXIS2_PLACEMENT_3D('',#41355,#41356,#41357); -#41359=PLANE('',#41358); -#41360=ORIENTED_EDGE('',*,*,#26024,.F.); -#41362=ORIENTED_EDGE('',*,*,#41361,.T.); -#41363=ORIENTED_EDGE('',*,*,#29760,.T.); -#41364=ORIENTED_EDGE('',*,*,#41348,.F.); -#41365=EDGE_LOOP('',(#41360,#41362,#41363,#41364)); -#41366=FACE_OUTER_BOUND('',#41365,.F.); -#41368=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.84375E0)); -#41369=DIRECTION('',(-6.611562980142E-1,0.E0,7.502481919980E-1)); -#41370=DIRECTION('',(7.502481919980E-1,0.E0,6.611562980142E-1)); -#41371=AXIS2_PLACEMENT_3D('',#41368,#41369,#41370); -#41372=PLANE('',#41371); -#41373=ORIENTED_EDGE('',*,*,#26022,.F.); -#41375=ORIENTED_EDGE('',*,*,#41374,.T.); -#41376=ORIENTED_EDGE('',*,*,#29762,.T.); -#41377=ORIENTED_EDGE('',*,*,#41361,.F.); -#41378=EDGE_LOOP('',(#41373,#41375,#41376,#41377)); -#41379=FACE_OUTER_BOUND('',#41378,.F.); -#41381=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.749999713898E0)); -#41382=DIRECTION('',(-8.266000777833E-1,0.E0,5.627897577325E-1)); -#41383=DIRECTION('',(5.627897577325E-1,0.E0,8.266000777833E-1)); -#41384=AXIS2_PLACEMENT_3D('',#41381,#41382,#41383); -#41385=PLANE('',#41384); -#41386=ORIENTED_EDGE('',*,*,#26020,.F.); -#41388=ORIENTED_EDGE('',*,*,#41387,.T.); -#41389=ORIENTED_EDGE('',*,*,#29764,.T.); -#41390=ORIENTED_EDGE('',*,*,#41374,.F.); -#41391=EDGE_LOOP('',(#41386,#41388,#41389,#41390)); -#41392=FACE_OUTER_BOUND('',#41391,.F.); -#41394=CARTESIAN_POINT('',(4.75E0,1.55E0,1.656250286102E0)); -#41395=DIRECTION('',(-9.752004643543E-1,0.E0,2.213234156683E-1)); -#41396=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#41397=AXIS2_PLACEMENT_3D('',#41394,#41395,#41396); -#41398=PLANE('',#41397); -#41399=ORIENTED_EDGE('',*,*,#26018,.F.); -#41401=ORIENTED_EDGE('',*,*,#41400,.T.); -#41402=ORIENTED_EDGE('',*,*,#29766,.T.); -#41403=ORIENTED_EDGE('',*,*,#41387,.F.); -#41404=EDGE_LOOP('',(#41399,#41401,#41402,#41403)); -#41405=FACE_OUTER_BOUND('',#41404,.F.); -#41407=CARTESIAN_POINT('',(4.75E0,1.55E0,1.581249713898E0)); -#41408=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41409=DIRECTION('',(0.E0,0.E0,1.E0)); -#41410=AXIS2_PLACEMENT_3D('',#41407,#41408,#41409); -#41411=PLANE('',#41410); -#41412=ORIENTED_EDGE('',*,*,#26016,.F.); -#41414=ORIENTED_EDGE('',*,*,#41413,.T.); -#41415=ORIENTED_EDGE('',*,*,#29768,.T.); -#41416=ORIENTED_EDGE('',*,*,#41400,.F.); -#41417=EDGE_LOOP('',(#41412,#41414,#41415,#41416)); -#41418=FACE_OUTER_BOUND('',#41417,.F.); -#41420=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.487500286102E0)); -#41421=DIRECTION('',(-9.752004643543E-1,0.E0,-2.213234156683E-1)); -#41422=DIRECTION('',(-2.213234156683E-1,0.E0,9.752004643543E-1)); -#41423=AXIS2_PLACEMENT_3D('',#41420,#41421,#41422); -#41424=PLANE('',#41423); -#41425=ORIENTED_EDGE('',*,*,#26014,.F.); -#41427=ORIENTED_EDGE('',*,*,#41426,.T.); -#41428=ORIENTED_EDGE('',*,*,#29770,.T.); -#41429=ORIENTED_EDGE('',*,*,#41413,.F.); -#41430=EDGE_LOOP('',(#41425,#41427,#41428,#41429)); -#41431=FACE_OUTER_BOUND('',#41430,.F.); -#41433=CARTESIAN_POINT('',(4.835106372833E0,1.55E0,1.39375E0)); -#41434=DIRECTION('',(-8.266000777833E-1,0.E0,-5.627897577325E-1)); -#41435=DIRECTION('',(-5.627897577325E-1,0.E0,8.266000777833E-1)); -#41436=AXIS2_PLACEMENT_3D('',#41433,#41434,#41435); -#41437=PLANE('',#41436); -#41438=ORIENTED_EDGE('',*,*,#26012,.F.); -#41440=ORIENTED_EDGE('',*,*,#41439,.T.); -#41441=ORIENTED_EDGE('',*,*,#29772,.T.); -#41442=ORIENTED_EDGE('',*,*,#41426,.F.); -#41443=EDGE_LOOP('',(#41438,#41440,#41441,#41442)); -#41444=FACE_OUTER_BOUND('',#41443,.F.); -#41446=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.3375E0)); -#41447=DIRECTION('',(-6.611562980142E-1,0.E0,-7.502481919980E-1)); -#41448=DIRECTION('',(-7.502481919980E-1,0.E0,6.611562980142E-1)); -#41449=AXIS2_PLACEMENT_3D('',#41446,#41447,#41448); -#41450=PLANE('',#41449); -#41451=ORIENTED_EDGE('',*,*,#26010,.F.); -#41453=ORIENTED_EDGE('',*,*,#41452,.T.); -#41454=ORIENTED_EDGE('',*,*,#29774,.T.); -#41455=ORIENTED_EDGE('',*,*,#41439,.F.); -#41456=EDGE_LOOP('',(#41451,#41453,#41454,#41455)); -#41457=FACE_OUTER_BOUND('',#41456,.F.); -#41459=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.299999713898E0)); -#41460=DIRECTION('',(-3.324522241845E-1,0.E0,-9.431200976730E-1)); -#41461=DIRECTION('',(-9.431200976730E-1,0.E0,3.324522241845E-1)); -#41462=AXIS2_PLACEMENT_3D('',#41459,#41460,#41461); -#41463=PLANE('',#41462); -#41464=ORIENTED_EDGE('',*,*,#26008,.F.); -#41466=ORIENTED_EDGE('',*,*,#41465,.T.); -#41467=ORIENTED_EDGE('',*,*,#29776,.T.); -#41468=ORIENTED_EDGE('',*,*,#41452,.F.); -#41469=EDGE_LOOP('',(#41464,#41466,#41467,#41468)); -#41470=FACE_OUTER_BOUND('',#41469,.F.); -#41472=CARTESIAN_POINT('',(5.069148957729E0,1.55E0,1.299999713898E0)); -#41473=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41474=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41475=AXIS2_PLACEMENT_3D('',#41472,#41473,#41474); -#41476=PLANE('',#41475); -#41477=ORIENTED_EDGE('',*,*,#26006,.F.); -#41479=ORIENTED_EDGE('',*,*,#41478,.T.); -#41480=ORIENTED_EDGE('',*,*,#29778,.T.); -#41481=ORIENTED_EDGE('',*,*,#41465,.F.); -#41482=EDGE_LOOP('',(#41477,#41479,#41480,#41481)); -#41483=FACE_OUTER_BOUND('',#41482,.F.); -#41485=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,1.3375E0)); -#41486=DIRECTION('',(4.032203477633E-1,0.E0,-9.151029183374E-1)); -#41487=DIRECTION('',(-9.151029183374E-1,0.E0,-4.032203477633E-1)); -#41488=AXIS2_PLACEMENT_3D('',#41485,#41486,#41487); -#41489=PLANE('',#41488); -#41490=ORIENTED_EDGE('',*,*,#26004,.F.); -#41492=ORIENTED_EDGE('',*,*,#41491,.T.); -#41493=ORIENTED_EDGE('',*,*,#29780,.T.); -#41494=ORIENTED_EDGE('',*,*,#41478,.F.); -#41495=EDGE_LOOP('',(#41490,#41492,#41493,#41494)); -#41496=FACE_OUTER_BOUND('',#41495,.F.); -#41498=CARTESIAN_POINT('',(5.218085110188E0,1.55E0,1.39375E0)); -#41499=DIRECTION('',(6.611562980142E-1,0.E0,-7.502481919980E-1)); -#41500=DIRECTION('',(-7.502481919980E-1,0.E0,-6.611562980142E-1)); -#41501=AXIS2_PLACEMENT_3D('',#41498,#41499,#41500); -#41502=PLANE('',#41501); -#41503=ORIENTED_EDGE('',*,*,#26002,.F.); -#41505=ORIENTED_EDGE('',*,*,#41504,.T.); -#41506=ORIENTED_EDGE('',*,*,#29782,.T.); -#41507=ORIENTED_EDGE('',*,*,#41491,.F.); -#41508=EDGE_LOOP('',(#41503,#41505,#41506,#41507)); -#41509=FACE_OUTER_BOUND('',#41508,.F.); -#41511=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,1.431250286102E0)); -#41512=DIRECTION('',(8.697591154214E-1,0.E0,-4.934765254207E-1)); -#41513=DIRECTION('',(-4.934765254207E-1,0.E0,-8.697591154214E-1)); -#41514=AXIS2_PLACEMENT_3D('',#41511,#41512,#41513); -#41515=PLANE('',#41514); -#41516=ORIENTED_EDGE('',*,*,#26000,.F.); -#41518=ORIENTED_EDGE('',*,*,#41517,.T.); -#41519=ORIENTED_EDGE('',*,*,#29784,.T.); -#41520=ORIENTED_EDGE('',*,*,#41504,.F.); -#41521=EDGE_LOOP('',(#41516,#41518,#41519,#41520)); -#41522=FACE_OUTER_BOUND('',#41521,.F.); -#41524=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.39375E0)); -#41525=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#41526=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#41527=AXIS2_PLACEMENT_3D('',#41524,#41525,#41526); -#41528=PLANE('',#41527); -#41529=ORIENTED_EDGE('',*,*,#25998,.F.); -#41531=ORIENTED_EDGE('',*,*,#41530,.T.); -#41532=ORIENTED_EDGE('',*,*,#29786,.T.); -#41533=ORIENTED_EDGE('',*,*,#41517,.F.); -#41534=EDGE_LOOP('',(#41529,#41531,#41532,#41533)); -#41535=FACE_OUTER_BOUND('',#41534,.F.); -#41537=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.318750286102E0)); -#41538=DIRECTION('',(-7.615382075403E-1,0.E0,-6.481200185586E-1)); -#41539=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#41540=AXIS2_PLACEMENT_3D('',#41537,#41538,#41539); -#41541=PLANE('',#41540); -#41542=ORIENTED_EDGE('',*,*,#25996,.F.); -#41544=ORIENTED_EDGE('',*,*,#41543,.T.); -#41545=ORIENTED_EDGE('',*,*,#29788,.T.); -#41546=ORIENTED_EDGE('',*,*,#41530,.F.); -#41547=EDGE_LOOP('',(#41542,#41544,#41545,#41546)); -#41548=FACE_OUTER_BOUND('',#41547,.F.); -#41550=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.28125E0)); -#41551=DIRECTION('',(-3.324523070247E-1,0.E0,-9.431200684716E-1)); -#41552=DIRECTION('',(-9.431200684716E-1,0.E0,3.324523070247E-1)); -#41553=AXIS2_PLACEMENT_3D('',#41550,#41551,#41552); -#41554=PLANE('',#41553); -#41555=ORIENTED_EDGE('',*,*,#25994,.F.); -#41557=ORIENTED_EDGE('',*,*,#41556,.T.); -#41558=ORIENTED_EDGE('',*,*,#29790,.T.); -#41559=ORIENTED_EDGE('',*,*,#41543,.F.); -#41560=EDGE_LOOP('',(#41555,#41557,#41558,#41559)); -#41561=FACE_OUTER_BOUND('',#41560,.F.); -#41563=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.28125E0)); -#41564=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41565=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41566=AXIS2_PLACEMENT_3D('',#41563,#41564,#41565); -#41567=PLANE('',#41566); -#41568=ORIENTED_EDGE('',*,*,#25992,.F.); -#41570=ORIENTED_EDGE('',*,*,#41569,.T.); -#41571=ORIENTED_EDGE('',*,*,#29792,.T.); -#41572=ORIENTED_EDGE('',*,*,#41556,.F.); -#41573=EDGE_LOOP('',(#41568,#41570,#41571,#41572)); -#41574=FACE_OUTER_BOUND('',#41573,.F.); -#41576=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.318750286102E0)); -#41577=DIRECTION('',(3.324523484448E-1,0.E0,-9.431200538709E-1)); -#41578=DIRECTION('',(-9.431200538709E-1,0.E0,-3.324523484448E-1)); -#41579=AXIS2_PLACEMENT_3D('',#41576,#41577,#41578); -#41580=PLANE('',#41579); -#41581=ORIENTED_EDGE('',*,*,#25990,.F.); -#41583=ORIENTED_EDGE('',*,*,#41582,.T.); -#41584=ORIENTED_EDGE('',*,*,#29794,.T.); -#41585=ORIENTED_EDGE('',*,*,#41569,.F.); -#41586=EDGE_LOOP('',(#41581,#41583,#41584,#41585)); -#41587=FACE_OUTER_BOUND('',#41586,.F.); -#41589=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.375000286102E0)); -#41590=DIRECTION('',(6.611562545751E-1,0.E0,-7.502482302787E-1)); -#41591=DIRECTION('',(-7.502482302787E-1,0.E0,-6.611562545751E-1)); -#41592=AXIS2_PLACEMENT_3D('',#41589,#41590,#41591); -#41593=PLANE('',#41592); -#41594=ORIENTED_EDGE('',*,*,#25988,.F.); -#41596=ORIENTED_EDGE('',*,*,#41595,.T.); -#41597=ORIENTED_EDGE('',*,*,#29796,.T.); -#41598=ORIENTED_EDGE('',*,*,#41582,.F.); -#41599=EDGE_LOOP('',(#41594,#41596,#41597,#41598)); -#41600=FACE_OUTER_BOUND('',#41599,.F.); -#41602=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.468749713898E0)); -#41603=DIRECTION('',(8.265976578970E-1,0.E0,-5.627933119354E-1)); -#41604=DIRECTION('',(-5.627933119354E-1,0.E0,-8.265976578970E-1)); -#41605=AXIS2_PLACEMENT_3D('',#41602,#41603,#41604); -#41606=PLANE('',#41605); -#41607=ORIENTED_EDGE('',*,*,#25986,.F.); -#41609=ORIENTED_EDGE('',*,*,#41608,.T.); -#41610=ORIENTED_EDGE('',*,*,#29798,.T.); -#41611=ORIENTED_EDGE('',*,*,#41595,.F.); -#41612=EDGE_LOOP('',(#41607,#41609,#41610,#41611)); -#41613=FACE_OUTER_BOUND('',#41612,.F.); -#41615=CARTESIAN_POINT('',(5.75E0,1.55E0,1.5625E0)); -#41616=DIRECTION('',(9.752008975102E-1,0.E0,-2.213215070781E-1)); -#41617=DIRECTION('',(-2.213215070781E-1,0.E0,-9.752008975102E-1)); -#41618=AXIS2_PLACEMENT_3D('',#41615,#41616,#41617); -#41619=PLANE('',#41618); -#41620=ORIENTED_EDGE('',*,*,#25984,.F.); -#41622=ORIENTED_EDGE('',*,*,#41621,.T.); -#41623=ORIENTED_EDGE('',*,*,#29800,.T.); -#41624=ORIENTED_EDGE('',*,*,#41608,.F.); -#41625=EDGE_LOOP('',(#41620,#41622,#41623,#41624)); -#41626=FACE_OUTER_BOUND('',#41625,.F.); -#41628=CARTESIAN_POINT('',(5.75E0,1.55E0,1.675E0)); -#41629=DIRECTION('',(1.E0,0.E0,0.E0)); -#41630=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41631=AXIS2_PLACEMENT_3D('',#41628,#41629,#41630); -#41632=PLANE('',#41631); -#41633=ORIENTED_EDGE('',*,*,#25982,.F.); -#41635=ORIENTED_EDGE('',*,*,#41634,.T.); -#41636=ORIENTED_EDGE('',*,*,#29802,.T.); -#41637=ORIENTED_EDGE('',*,*,#41621,.F.); -#41638=EDGE_LOOP('',(#41633,#41635,#41636,#41637)); -#41639=FACE_OUTER_BOUND('',#41638,.F.); -#41641=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,1.768750286102E0)); -#41642=DIRECTION('',(9.752008975102E-1,0.E0,2.213215070781E-1)); -#41643=DIRECTION('',(2.213215070781E-1,0.E0,-9.752008975102E-1)); -#41644=AXIS2_PLACEMENT_3D('',#41641,#41642,#41643); -#41645=PLANE('',#41644); -#41646=ORIENTED_EDGE('',*,*,#25980,.F.); -#41648=ORIENTED_EDGE('',*,*,#41647,.T.); -#41649=ORIENTED_EDGE('',*,*,#29804,.T.); -#41650=ORIENTED_EDGE('',*,*,#41634,.F.); -#41651=EDGE_LOOP('',(#41646,#41648,#41649,#41650)); -#41652=FACE_OUTER_BOUND('',#41651,.F.); -#41654=CARTESIAN_POINT('',(5.664893619716E0,1.55E0,1.862499713898E0)); -#41655=DIRECTION('',(8.265976578970E-1,0.E0,5.627933119354E-1)); -#41656=DIRECTION('',(5.627933119354E-1,0.E0,-8.265976578970E-1)); -#41657=AXIS2_PLACEMENT_3D('',#41654,#41655,#41656); -#41658=PLANE('',#41657); -#41659=ORIENTED_EDGE('',*,*,#25978,.F.); -#41661=ORIENTED_EDGE('',*,*,#41660,.T.); -#41662=ORIENTED_EDGE('',*,*,#29806,.T.); -#41663=ORIENTED_EDGE('',*,*,#41647,.F.); -#41664=EDGE_LOOP('',(#41659,#41661,#41662,#41663)); -#41665=FACE_OUTER_BOUND('',#41664,.F.); -#41667=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,1.918749713898E0)); -#41668=DIRECTION('',(6.611562545751E-1,0.E0,7.502482302787E-1)); -#41669=DIRECTION('',(7.502482302787E-1,0.E0,-6.611562545751E-1)); -#41670=AXIS2_PLACEMENT_3D('',#41667,#41668,#41669); -#41671=PLANE('',#41670); -#41672=ORIENTED_EDGE('',*,*,#25976,.F.); -#41674=ORIENTED_EDGE('',*,*,#41673,.T.); -#41675=ORIENTED_EDGE('',*,*,#29808,.T.); -#41676=ORIENTED_EDGE('',*,*,#41660,.F.); -#41677=EDGE_LOOP('',(#41672,#41674,#41675,#41676)); -#41678=FACE_OUTER_BOUND('',#41677,.F.); -#41680=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.95625E0)); -#41681=DIRECTION('',(3.324523484448E-1,0.E0,9.431200538709E-1)); -#41682=DIRECTION('',(9.431200538709E-1,0.E0,-3.324523484448E-1)); -#41683=AXIS2_PLACEMENT_3D('',#41680,#41681,#41682); -#41684=PLANE('',#41683); -#41685=ORIENTED_EDGE('',*,*,#25974,.F.); -#41687=ORIENTED_EDGE('',*,*,#41686,.T.); -#41688=ORIENTED_EDGE('',*,*,#29810,.T.); -#41689=ORIENTED_EDGE('',*,*,#41673,.F.); -#41690=EDGE_LOOP('',(#41685,#41687,#41688,#41689)); -#41691=FACE_OUTER_BOUND('',#41690,.F.); -#41693=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.95625E0)); -#41694=DIRECTION('',(0.E0,0.E0,1.E0)); -#41695=DIRECTION('',(1.E0,0.E0,0.E0)); -#41696=AXIS2_PLACEMENT_3D('',#41693,#41694,#41695); -#41697=PLANE('',#41696); -#41698=ORIENTED_EDGE('',*,*,#25972,.F.); -#41700=ORIENTED_EDGE('',*,*,#41699,.T.); -#41701=ORIENTED_EDGE('',*,*,#29812,.T.); -#41702=ORIENTED_EDGE('',*,*,#41686,.F.); -#41703=EDGE_LOOP('',(#41698,#41700,#41701,#41702)); -#41704=FACE_OUTER_BOUND('',#41703,.F.); -#41706=CARTESIAN_POINT('',(5.324468076229E0,1.55E0,1.918749713898E0)); -#41707=DIRECTION('',(-3.324523070247E-1,0.E0,9.431200684716E-1)); -#41708=DIRECTION('',(9.431200684716E-1,0.E0,3.324523070247E-1)); -#41709=AXIS2_PLACEMENT_3D('',#41706,#41707,#41708); -#41710=PLANE('',#41709); -#41711=ORIENTED_EDGE('',*,*,#25970,.F.); -#41713=ORIENTED_EDGE('',*,*,#41712,.T.); -#41714=ORIENTED_EDGE('',*,*,#29814,.T.); -#41715=ORIENTED_EDGE('',*,*,#41699,.F.); -#41716=EDGE_LOOP('',(#41711,#41713,#41714,#41715)); -#41717=FACE_OUTER_BOUND('',#41716,.F.); -#41719=CARTESIAN_POINT('',(5.260638296604E0,1.55E0,1.84375E0)); -#41720=DIRECTION('',(-7.615382075403E-1,0.E0,6.481200185586E-1)); -#41721=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#41722=AXIS2_PLACEMENT_3D('',#41719,#41720,#41721); -#41723=PLANE('',#41722); -#41724=ORIENTED_EDGE('',*,*,#25968,.F.); -#41725=ORIENTED_EDGE('',*,*,#41298,.T.); -#41726=ORIENTED_EDGE('',*,*,#29816,.T.); -#41727=ORIENTED_EDGE('',*,*,#41712,.F.); -#41728=EDGE_LOOP('',(#41724,#41725,#41726,#41727)); -#41729=FACE_OUTER_BOUND('',#41728,.F.); -#41731=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.656250286102E0)); -#41732=DIRECTION('',(-9.620369340052E-1,0.E0,-2.729192877205E-1)); -#41733=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#41734=AXIS2_PLACEMENT_3D('',#41731,#41732,#41733); -#41735=PLANE('',#41734); -#41736=ORIENTED_EDGE('',*,*,#26922,.F.); -#41738=ORIENTED_EDGE('',*,*,#41737,.T.); -#41739=ORIENTED_EDGE('',*,*,#29820,.T.); -#41741=ORIENTED_EDGE('',*,*,#41740,.F.); -#41742=EDGE_LOOP('',(#41736,#41738,#41739,#41741)); -#41743=FACE_OUTER_BOUND('',#41742,.F.); -#41745=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.581249713898E0)); -#41746=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41747=DIRECTION('',(0.E0,0.E0,1.E0)); -#41748=AXIS2_PLACEMENT_3D('',#41745,#41746,#41747); -#41749=PLANE('',#41748); -#41750=ORIENTED_EDGE('',*,*,#26952,.F.); -#41752=ORIENTED_EDGE('',*,*,#41751,.T.); -#41753=ORIENTED_EDGE('',*,*,#29822,.T.); -#41754=ORIENTED_EDGE('',*,*,#41737,.F.); -#41755=EDGE_LOOP('',(#41750,#41752,#41753,#41754)); -#41756=FACE_OUTER_BOUND('',#41755,.F.); -#41758=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.50625E0)); -#41759=DIRECTION('',(-9.620369340052E-1,0.E0,2.729192877205E-1)); -#41760=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#41761=AXIS2_PLACEMENT_3D('',#41758,#41759,#41760); -#41762=PLANE('',#41761); -#41763=ORIENTED_EDGE('',*,*,#26950,.F.); -#41765=ORIENTED_EDGE('',*,*,#41764,.T.); -#41766=ORIENTED_EDGE('',*,*,#29824,.T.); -#41767=ORIENTED_EDGE('',*,*,#41751,.F.); -#41768=EDGE_LOOP('',(#41763,#41765,#41766,#41767)); -#41769=FACE_OUTER_BOUND('',#41768,.F.); -#41771=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.431250286102E0)); -#41772=DIRECTION('',(-8.697566915162E-1,0.E0,4.934807975624E-1)); -#41773=DIRECTION('',(4.934807975624E-1,0.E0,8.697566915162E-1)); -#41774=AXIS2_PLACEMENT_3D('',#41771,#41772,#41773); -#41775=PLANE('',#41774); -#41776=ORIENTED_EDGE('',*,*,#26948,.F.); -#41778=ORIENTED_EDGE('',*,*,#41777,.T.); -#41779=ORIENTED_EDGE('',*,*,#29826,.T.); -#41780=ORIENTED_EDGE('',*,*,#41764,.F.); -#41781=EDGE_LOOP('',(#41776,#41778,#41779,#41780)); -#41782=FACE_OUTER_BOUND('',#41781,.F.); -#41784=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.375000286102E0)); -#41785=DIRECTION('',(-5.513868654785E-1,0.E0,8.342496776013E-1)); -#41786=DIRECTION('',(8.342496776013E-1,0.E0,5.513868654785E-1)); -#41787=AXIS2_PLACEMENT_3D('',#41784,#41785,#41786); -#41788=PLANE('',#41787); -#41789=ORIENTED_EDGE('',*,*,#26946,.F.); -#41791=ORIENTED_EDGE('',*,*,#41790,.T.); -#41792=ORIENTED_EDGE('',*,*,#29828,.T.); -#41793=ORIENTED_EDGE('',*,*,#41777,.F.); -#41794=EDGE_LOOP('',(#41789,#41791,#41792,#41793)); -#41795=FACE_OUTER_BOUND('',#41794,.F.); -#41797=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.375000286102E0)); -#41798=DIRECTION('',(0.E0,0.E0,1.E0)); -#41799=DIRECTION('',(1.E0,0.E0,0.E0)); -#41800=AXIS2_PLACEMENT_3D('',#41797,#41798,#41799); -#41801=PLANE('',#41800); -#41802=ORIENTED_EDGE('',*,*,#26944,.F.); -#41804=ORIENTED_EDGE('',*,*,#41803,.T.); -#41805=ORIENTED_EDGE('',*,*,#29830,.T.); -#41806=ORIENTED_EDGE('',*,*,#41790,.F.); -#41807=EDGE_LOOP('',(#41802,#41804,#41805,#41806)); -#41808=FACE_OUTER_BOUND('',#41807,.F.); -#41810=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.431250286102E0)); -#41811=DIRECTION('',(5.513867982882E-1,0.E0,8.342497220098E-1)); -#41812=DIRECTION('',(8.342497220098E-1,0.E0,-5.513867982882E-1)); -#41813=AXIS2_PLACEMENT_3D('',#41810,#41811,#41812); -#41814=PLANE('',#41813); -#41815=ORIENTED_EDGE('',*,*,#26942,.F.); -#41817=ORIENTED_EDGE('',*,*,#41816,.T.); -#41818=ORIENTED_EDGE('',*,*,#29832,.T.); -#41819=ORIENTED_EDGE('',*,*,#41803,.F.); -#41820=EDGE_LOOP('',(#41815,#41817,#41818,#41819)); -#41821=FACE_OUTER_BOUND('',#41820,.F.); -#41823=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.50625E0)); -#41824=DIRECTION('',(8.697566915162E-1,0.E0,4.934807975624E-1)); -#41825=DIRECTION('',(4.934807975624E-1,0.E0,-8.697566915162E-1)); -#41826=AXIS2_PLACEMENT_3D('',#41823,#41824,#41825); -#41827=PLANE('',#41826); -#41828=ORIENTED_EDGE('',*,*,#26940,.F.); -#41830=ORIENTED_EDGE('',*,*,#41829,.T.); -#41831=ORIENTED_EDGE('',*,*,#29834,.T.); -#41832=ORIENTED_EDGE('',*,*,#41816,.F.); -#41833=EDGE_LOOP('',(#41828,#41830,#41831,#41832)); -#41834=FACE_OUTER_BOUND('',#41833,.F.); -#41836=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.581249713898E0)); -#41837=DIRECTION('',(9.620369340052E-1,0.E0,2.729192877205E-1)); -#41838=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#41839=AXIS2_PLACEMENT_3D('',#41836,#41837,#41838); -#41840=PLANE('',#41839); -#41841=ORIENTED_EDGE('',*,*,#26938,.F.); -#41843=ORIENTED_EDGE('',*,*,#41842,.T.); -#41844=ORIENTED_EDGE('',*,*,#29836,.T.); -#41845=ORIENTED_EDGE('',*,*,#41829,.F.); -#41846=EDGE_LOOP('',(#41841,#41843,#41844,#41845)); -#41847=FACE_OUTER_BOUND('',#41846,.F.); -#41849=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,1.656250286102E0)); -#41850=DIRECTION('',(1.E0,0.E0,0.E0)); -#41851=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41852=AXIS2_PLACEMENT_3D('',#41849,#41850,#41851); -#41853=PLANE('',#41852); -#41854=ORIENTED_EDGE('',*,*,#26936,.F.); -#41856=ORIENTED_EDGE('',*,*,#41855,.T.); -#41857=ORIENTED_EDGE('',*,*,#29838,.T.); -#41858=ORIENTED_EDGE('',*,*,#41842,.F.); -#41859=EDGE_LOOP('',(#41854,#41856,#41857,#41858)); -#41860=FACE_OUTER_BOUND('',#41859,.F.); -#41862=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,1.73125E0)); -#41863=DIRECTION('',(9.620369340052E-1,0.E0,-2.729192877205E-1)); -#41864=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#41865=AXIS2_PLACEMENT_3D('',#41862,#41863,#41864); -#41866=PLANE('',#41865); -#41867=ORIENTED_EDGE('',*,*,#26934,.F.); -#41869=ORIENTED_EDGE('',*,*,#41868,.T.); -#41870=ORIENTED_EDGE('',*,*,#29840,.T.); -#41871=ORIENTED_EDGE('',*,*,#41855,.F.); -#41872=EDGE_LOOP('',(#41867,#41869,#41870,#41871)); -#41873=FACE_OUTER_BOUND('',#41872,.F.); -#41875=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,1.806249713898E0)); -#41876=DIRECTION('',(8.697566915162E-1,0.E0,-4.934807975624E-1)); -#41877=DIRECTION('',(-4.934807975624E-1,0.E0,-8.697566915162E-1)); -#41878=AXIS2_PLACEMENT_3D('',#41875,#41876,#41877); -#41879=PLANE('',#41878); -#41880=ORIENTED_EDGE('',*,*,#26932,.F.); -#41882=ORIENTED_EDGE('',*,*,#41881,.T.); -#41883=ORIENTED_EDGE('',*,*,#29842,.T.); -#41884=ORIENTED_EDGE('',*,*,#41868,.F.); -#41885=EDGE_LOOP('',(#41880,#41882,#41883,#41884)); -#41886=FACE_OUTER_BOUND('',#41885,.F.); -#41888=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,1.862499713898E0)); -#41889=DIRECTION('',(5.513867982882E-1,0.E0,-8.342497220099E-1)); -#41890=DIRECTION('',(-8.342497220099E-1,0.E0,-5.513867982882E-1)); -#41891=AXIS2_PLACEMENT_3D('',#41888,#41889,#41890); -#41892=PLANE('',#41891); -#41893=ORIENTED_EDGE('',*,*,#26930,.F.); -#41895=ORIENTED_EDGE('',*,*,#41894,.T.); -#41896=ORIENTED_EDGE('',*,*,#29844,.T.); -#41897=ORIENTED_EDGE('',*,*,#41881,.F.); -#41898=EDGE_LOOP('',(#41893,#41895,#41896,#41897)); -#41899=FACE_OUTER_BOUND('',#41898,.F.); -#41901=CARTESIAN_POINT('',(5.494680851698E0,1.55E0,1.862499713898E0)); -#41902=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41903=DIRECTION('',(-1.E0,0.E0,0.E0)); -#41904=AXIS2_PLACEMENT_3D('',#41901,#41902,#41903); -#41905=PLANE('',#41904); -#41906=ORIENTED_EDGE('',*,*,#26928,.F.); -#41908=ORIENTED_EDGE('',*,*,#41907,.T.); -#41909=ORIENTED_EDGE('',*,*,#29846,.T.); -#41910=ORIENTED_EDGE('',*,*,#41894,.F.); -#41911=EDGE_LOOP('',(#41906,#41908,#41909,#41910)); -#41912=FACE_OUTER_BOUND('',#41911,.F.); -#41914=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.806249713898E0)); -#41915=DIRECTION('',(-5.513868654784E-1,0.E0,-8.342496776013E-1)); -#41916=DIRECTION('',(-8.342496776013E-1,0.E0,5.513868654784E-1)); -#41917=AXIS2_PLACEMENT_3D('',#41914,#41915,#41916); -#41918=PLANE('',#41917); -#41919=ORIENTED_EDGE('',*,*,#26926,.F.); -#41921=ORIENTED_EDGE('',*,*,#41920,.T.); -#41922=ORIENTED_EDGE('',*,*,#29848,.T.); -#41923=ORIENTED_EDGE('',*,*,#41907,.F.); -#41924=EDGE_LOOP('',(#41919,#41921,#41922,#41923)); -#41925=FACE_OUTER_BOUND('',#41924,.F.); -#41927=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,1.73125E0)); -#41928=DIRECTION('',(-8.697566915162E-1,0.E0,-4.934807975624E-1)); -#41929=DIRECTION('',(-4.934807975624E-1,0.E0,8.697566915162E-1)); -#41930=AXIS2_PLACEMENT_3D('',#41927,#41928,#41929); -#41931=PLANE('',#41930); -#41932=ORIENTED_EDGE('',*,*,#26924,.F.); -#41933=ORIENTED_EDGE('',*,*,#41740,.T.); -#41934=ORIENTED_EDGE('',*,*,#29850,.T.); -#41935=ORIENTED_EDGE('',*,*,#41920,.F.); -#41936=EDGE_LOOP('',(#41932,#41933,#41934,#41935)); -#41937=FACE_OUTER_BOUND('',#41936,.F.); -#41939=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.581249713898E0)); -#41940=DIRECTION('',(9.620369340052E-1,0.E0,2.729192877205E-1)); -#41941=DIRECTION('',(2.729192877205E-1,0.E0,-9.620369340052E-1)); -#41942=AXIS2_PLACEMENT_3D('',#41939,#41940,#41941); -#41943=PLANE('',#41942); -#41944=ORIENTED_EDGE('',*,*,#26962,.F.); -#41946=ORIENTED_EDGE('',*,*,#41945,.T.); -#41947=ORIENTED_EDGE('',*,*,#29854,.T.); -#41949=ORIENTED_EDGE('',*,*,#41948,.F.); -#41950=EDGE_LOOP('',(#41944,#41946,#41947,#41949)); -#41951=FACE_OUTER_BOUND('',#41950,.F.); -#41953=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,1.656250286102E0)); -#41954=DIRECTION('',(1.E0,0.E0,0.E0)); -#41955=DIRECTION('',(0.E0,0.E0,-1.E0)); -#41956=AXIS2_PLACEMENT_3D('',#41953,#41954,#41955); -#41957=PLANE('',#41956); -#41958=ORIENTED_EDGE('',*,*,#26992,.F.); -#41960=ORIENTED_EDGE('',*,*,#41959,.T.); -#41961=ORIENTED_EDGE('',*,*,#29856,.T.); -#41962=ORIENTED_EDGE('',*,*,#41945,.F.); -#41963=EDGE_LOOP('',(#41958,#41960,#41961,#41962)); -#41964=FACE_OUTER_BOUND('',#41963,.F.); -#41966=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.73125E0)); -#41967=DIRECTION('',(9.620369340052E-1,0.E0,-2.729192877205E-1)); -#41968=DIRECTION('',(-2.729192877205E-1,0.E0,-9.620369340052E-1)); -#41969=AXIS2_PLACEMENT_3D('',#41966,#41967,#41968); -#41970=PLANE('',#41969); -#41971=ORIENTED_EDGE('',*,*,#26990,.F.); -#41973=ORIENTED_EDGE('',*,*,#41972,.T.); -#41974=ORIENTED_EDGE('',*,*,#29858,.T.); -#41975=ORIENTED_EDGE('',*,*,#41959,.F.); -#41976=EDGE_LOOP('',(#41971,#41973,#41974,#41975)); -#41977=FACE_OUTER_BOUND('',#41976,.F.); -#41979=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.806249713898E0)); -#41980=DIRECTION('',(7.615382075403E-1,0.E0,-6.481200185586E-1)); -#41981=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#41982=AXIS2_PLACEMENT_3D('',#41979,#41980,#41981); -#41983=PLANE('',#41982); -#41984=ORIENTED_EDGE('',*,*,#26988,.F.); -#41986=ORIENTED_EDGE('',*,*,#41985,.T.); -#41987=ORIENTED_EDGE('',*,*,#29860,.T.); -#41988=ORIENTED_EDGE('',*,*,#41972,.F.); -#41989=EDGE_LOOP('',(#41984,#41986,#41987,#41988)); -#41990=FACE_OUTER_BOUND('',#41989,.F.); -#41992=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.84375E0)); -#41993=DIRECTION('',(5.065516148884E-1,0.E0,-8.622096389243E-1)); -#41994=DIRECTION('',(-8.622096389243E-1,0.E0,-5.065516148884E-1)); -#41995=AXIS2_PLACEMENT_3D('',#41992,#41993,#41994); -#41996=PLANE('',#41995); -#41997=ORIENTED_EDGE('',*,*,#26986,.F.); -#41999=ORIENTED_EDGE('',*,*,#41998,.T.); -#42000=ORIENTED_EDGE('',*,*,#29862,.T.); -#42001=ORIENTED_EDGE('',*,*,#41985,.F.); -#42002=EDGE_LOOP('',(#41997,#41999,#42000,#42001)); -#42003=FACE_OUTER_BOUND('',#42002,.F.); -#42005=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.84375E0)); -#42006=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42007=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42008=AXIS2_PLACEMENT_3D('',#42005,#42006,#42007); -#42009=PLANE('',#42008); -#42010=ORIENTED_EDGE('',*,*,#26984,.F.); -#42012=ORIENTED_EDGE('',*,*,#42011,.T.); -#42013=ORIENTED_EDGE('',*,*,#29864,.T.); -#42014=ORIENTED_EDGE('',*,*,#41998,.F.); -#42015=EDGE_LOOP('',(#42010,#42012,#42013,#42014)); -#42016=FACE_OUTER_BOUND('',#42015,.F.); -#42018=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.806249713898E0)); -#42019=DIRECTION('',(-5.065519665347E-1,0.E0,-8.622094323306E-1)); -#42020=DIRECTION('',(-8.622094323306E-1,0.E0,5.065519665347E-1)); -#42021=AXIS2_PLACEMENT_3D('',#42018,#42019,#42020); -#42022=PLANE('',#42021); -#42023=ORIENTED_EDGE('',*,*,#26982,.F.); -#42025=ORIENTED_EDGE('',*,*,#42024,.T.); -#42026=ORIENTED_EDGE('',*,*,#29866,.T.); -#42027=ORIENTED_EDGE('',*,*,#42011,.F.); -#42028=EDGE_LOOP('',(#42023,#42025,#42026,#42027)); -#42029=FACE_OUTER_BOUND('',#42028,.F.); -#42031=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.73125E0)); -#42032=DIRECTION('',(-7.615382075403E-1,0.E0,-6.481200185586E-1)); -#42033=DIRECTION('',(-6.481200185586E-1,0.E0,7.615382075403E-1)); -#42034=AXIS2_PLACEMENT_3D('',#42031,#42032,#42033); -#42035=PLANE('',#42034); -#42036=ORIENTED_EDGE('',*,*,#26980,.F.); -#42038=ORIENTED_EDGE('',*,*,#42037,.T.); -#42039=ORIENTED_EDGE('',*,*,#29868,.T.); -#42040=ORIENTED_EDGE('',*,*,#42024,.F.); -#42041=EDGE_LOOP('',(#42036,#42038,#42039,#42040)); -#42042=FACE_OUTER_BOUND('',#42041,.F.); -#42044=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.656250286102E0)); -#42045=DIRECTION('',(-9.620369340052E-1,0.E0,-2.729192877205E-1)); -#42046=DIRECTION('',(-2.729192877205E-1,0.E0,9.620369340052E-1)); -#42047=AXIS2_PLACEMENT_3D('',#42044,#42045,#42046); -#42048=PLANE('',#42047); -#42049=ORIENTED_EDGE('',*,*,#26978,.F.); -#42051=ORIENTED_EDGE('',*,*,#42050,.T.); -#42052=ORIENTED_EDGE('',*,*,#29870,.T.); -#42053=ORIENTED_EDGE('',*,*,#42037,.F.); -#42054=EDGE_LOOP('',(#42049,#42051,#42052,#42053)); -#42055=FACE_OUTER_BOUND('',#42054,.F.); -#42057=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,1.581249713898E0)); -#42058=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42059=DIRECTION('',(0.E0,0.E0,1.E0)); -#42060=AXIS2_PLACEMENT_3D('',#42057,#42058,#42059); -#42061=PLANE('',#42060); -#42062=ORIENTED_EDGE('',*,*,#26976,.F.); -#42064=ORIENTED_EDGE('',*,*,#42063,.T.); -#42065=ORIENTED_EDGE('',*,*,#29872,.T.); -#42066=ORIENTED_EDGE('',*,*,#42050,.F.); -#42067=EDGE_LOOP('',(#42062,#42064,#42065,#42066)); -#42068=FACE_OUTER_BOUND('',#42067,.F.); -#42070=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,1.50625E0)); -#42071=DIRECTION('',(-9.620369340052E-1,0.E0,2.729192877205E-1)); -#42072=DIRECTION('',(2.729192877205E-1,0.E0,9.620369340052E-1)); -#42073=AXIS2_PLACEMENT_3D('',#42070,#42071,#42072); -#42074=PLANE('',#42073); -#42075=ORIENTED_EDGE('',*,*,#26974,.F.); -#42077=ORIENTED_EDGE('',*,*,#42076,.T.); -#42078=ORIENTED_EDGE('',*,*,#29874,.T.); -#42079=ORIENTED_EDGE('',*,*,#42063,.F.); -#42080=EDGE_LOOP('',(#42075,#42077,#42078,#42079)); -#42081=FACE_OUTER_BOUND('',#42080,.F.); -#42083=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,1.431250286102E0)); -#42084=DIRECTION('',(-7.615382075403E-1,0.E0,6.481200185586E-1)); -#42085=DIRECTION('',(6.481200185586E-1,0.E0,7.615382075403E-1)); -#42086=AXIS2_PLACEMENT_3D('',#42083,#42084,#42085); -#42087=PLANE('',#42086); -#42088=ORIENTED_EDGE('',*,*,#26972,.F.); -#42090=ORIENTED_EDGE('',*,*,#42089,.T.); -#42091=ORIENTED_EDGE('',*,*,#29876,.T.); -#42092=ORIENTED_EDGE('',*,*,#42076,.F.); -#42093=EDGE_LOOP('',(#42088,#42090,#42091,#42092)); -#42094=FACE_OUTER_BOUND('',#42093,.F.); -#42096=CARTESIAN_POINT('',(5.047872364521E0,1.55E0,1.39375E0)); -#42097=DIRECTION('',(-5.065519665348E-1,0.E0,8.622094323305E-1)); -#42098=DIRECTION('',(8.622094323305E-1,0.E0,5.065519665348E-1)); -#42099=AXIS2_PLACEMENT_3D('',#42096,#42097,#42098); -#42100=PLANE('',#42099); -#42101=ORIENTED_EDGE('',*,*,#26970,.F.); -#42103=ORIENTED_EDGE('',*,*,#42102,.T.); -#42104=ORIENTED_EDGE('',*,*,#29878,.T.); -#42105=ORIENTED_EDGE('',*,*,#42089,.F.); -#42106=EDGE_LOOP('',(#42101,#42103,#42104,#42105)); -#42107=FACE_OUTER_BOUND('',#42106,.F.); -#42109=CARTESIAN_POINT('',(5.005319178104E0,1.55E0,1.39375E0)); -#42110=DIRECTION('',(0.E0,0.E0,1.E0)); -#42111=DIRECTION('',(1.E0,0.E0,0.E0)); -#42112=AXIS2_PLACEMENT_3D('',#42109,#42110,#42111); -#42113=PLANE('',#42112); -#42114=ORIENTED_EDGE('',*,*,#26968,.F.); -#42116=ORIENTED_EDGE('',*,*,#42115,.T.); -#42117=ORIENTED_EDGE('',*,*,#29880,.T.); -#42118=ORIENTED_EDGE('',*,*,#42102,.F.); -#42119=EDGE_LOOP('',(#42114,#42116,#42117,#42118)); -#42120=FACE_OUTER_BOUND('',#42119,.F.); -#42122=CARTESIAN_POINT('',(4.941489338875E0,1.55E0,1.431250286102E0)); -#42123=DIRECTION('',(5.065516148885E-1,0.E0,8.622096389243E-1)); -#42124=DIRECTION('',(8.622096389243E-1,0.E0,-5.065516148885E-1)); -#42125=AXIS2_PLACEMENT_3D('',#42122,#42123,#42124); -#42126=PLANE('',#42125); -#42127=ORIENTED_EDGE('',*,*,#26966,.F.); -#42129=ORIENTED_EDGE('',*,*,#42128,.T.); -#42130=ORIENTED_EDGE('',*,*,#29882,.T.); -#42131=ORIENTED_EDGE('',*,*,#42115,.F.); -#42132=EDGE_LOOP('',(#42127,#42129,#42130,#42131)); -#42133=FACE_OUTER_BOUND('',#42132,.F.); -#42135=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.50625E0)); -#42136=DIRECTION('',(7.615382075403E-1,0.E0,6.481200185586E-1)); -#42137=DIRECTION('',(6.481200185586E-1,0.E0,-7.615382075403E-1)); -#42138=AXIS2_PLACEMENT_3D('',#42135,#42136,#42137); -#42139=PLANE('',#42138); -#42140=ORIENTED_EDGE('',*,*,#26964,.F.); -#42141=ORIENTED_EDGE('',*,*,#41948,.T.); -#42142=ORIENTED_EDGE('',*,*,#29884,.T.); -#42143=ORIENTED_EDGE('',*,*,#42128,.F.); -#42144=EDGE_LOOP('',(#42140,#42141,#42142,#42143)); -#42145=FACE_OUTER_BOUND('',#42144,.F.); -#42147=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,5.124997138977E-1)); -#42148=DIRECTION('',(5.065433474453E-1,0.E0,-8.622144960269E-1)); -#42149=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#42150=AXIS2_PLACEMENT_3D('',#42147,#42148,#42149); -#42151=PLANE('',#42150); -#42152=ORIENTED_EDGE('',*,*,#26036,.F.); -#42154=ORIENTED_EDGE('',*,*,#42153,.T.); -#42155=ORIENTED_EDGE('',*,*,#29901,.T.); -#42157=ORIENTED_EDGE('',*,*,#42156,.F.); -#42158=EDGE_LOOP('',(#42152,#42154,#42155,#42157)); -#42159=FACE_OUTER_BOUND('',#42158,.F.); -#42161=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,5.687497138977E-1)); -#42162=DIRECTION('',(7.975044357522E-1,0.E0,-6.033130820359E-1)); -#42163=DIRECTION('',(-6.033130820359E-1,0.E0,-7.975044357522E-1)); -#42164=AXIS2_PLACEMENT_3D('',#42161,#42162,#42163); -#42165=PLANE('',#42164); -#42166=ORIENTED_EDGE('',*,*,#26148,.F.); -#42168=ORIENTED_EDGE('',*,*,#42167,.T.); -#42169=ORIENTED_EDGE('',*,*,#29903,.T.); -#42170=ORIENTED_EDGE('',*,*,#42153,.F.); -#42171=EDGE_LOOP('',(#42166,#42168,#42169,#42170)); -#42172=FACE_OUTER_BOUND('',#42171,.F.); -#42174=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,6.437502861023E-1)); -#42175=DIRECTION('',(8.697590876082E-1,0.E0,-4.934765744419E-1)); -#42176=DIRECTION('',(-4.934765744419E-1,0.E0,-8.697590876082E-1)); -#42177=AXIS2_PLACEMENT_3D('',#42174,#42175,#42176); -#42178=PLANE('',#42177); -#42179=ORIENTED_EDGE('',*,*,#26146,.F.); -#42181=ORIENTED_EDGE('',*,*,#42180,.T.); -#42182=ORIENTED_EDGE('',*,*,#29905,.T.); -#42183=ORIENTED_EDGE('',*,*,#42167,.F.); -#42184=EDGE_LOOP('',(#42179,#42181,#42182,#42183)); -#42185=FACE_OUTER_BOUND('',#42184,.F.); -#42187=CARTESIAN_POINT('',(5.75E0,1.55E0,7.1875E-1)); -#42188=DIRECTION('',(9.620369277320E-1,0.E0,-2.729193098334E-1)); -#42189=DIRECTION('',(-2.729193098334E-1,0.E0,-9.620369277320E-1)); -#42190=AXIS2_PLACEMENT_3D('',#42187,#42188,#42189); -#42191=PLANE('',#42190); -#42192=ORIENTED_EDGE('',*,*,#26144,.F.); -#42194=ORIENTED_EDGE('',*,*,#42193,.T.); -#42195=ORIENTED_EDGE('',*,*,#29907,.T.); -#42196=ORIENTED_EDGE('',*,*,#42180,.F.); -#42197=EDGE_LOOP('',(#42192,#42194,#42195,#42196)); -#42198=FACE_OUTER_BOUND('',#42197,.F.); -#42200=CARTESIAN_POINT('',(5.75E0,1.55E0,8.687502861023E-1)); -#42201=DIRECTION('',(1.E0,0.E0,0.E0)); -#42202=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42203=AXIS2_PLACEMENT_3D('',#42200,#42201,#42202); -#42204=PLANE('',#42203); -#42205=ORIENTED_EDGE('',*,*,#26142,.F.); -#42207=ORIENTED_EDGE('',*,*,#42206,.T.); -#42208=ORIENTED_EDGE('',*,*,#29909,.T.); -#42209=ORIENTED_EDGE('',*,*,#42193,.F.); -#42210=EDGE_LOOP('',(#42205,#42207,#42208,#42209)); -#42211=FACE_OUTER_BOUND('',#42210,.F.); -#42213=CARTESIAN_POINT('',(5.728723404929E0,1.55E0,9.4375E-1)); -#42214=DIRECTION('',(9.620369277320E-1,0.E0,2.729193098334E-1)); -#42215=DIRECTION('',(2.729193098334E-1,0.E0,-9.620369277320E-1)); -#42216=AXIS2_PLACEMENT_3D('',#42213,#42214,#42215); -#42217=PLANE('',#42216); -#42218=ORIENTED_EDGE('',*,*,#26140,.F.); -#42220=ORIENTED_EDGE('',*,*,#42219,.T.); -#42221=ORIENTED_EDGE('',*,*,#29911,.T.); -#42222=ORIENTED_EDGE('',*,*,#42206,.F.); -#42223=EDGE_LOOP('',(#42218,#42220,#42221,#42222)); -#42224=FACE_OUTER_BOUND('',#42223,.F.); -#42226=CARTESIAN_POINT('',(5.686170212924E0,1.55E0,1.018749713898E0)); -#42227=DIRECTION('',(8.697566637025E-1,0.E0,4.934808465838E-1)); -#42228=DIRECTION('',(4.934808465838E-1,0.E0,-8.697566637025E-1)); -#42229=AXIS2_PLACEMENT_3D('',#42226,#42227,#42228); -#42230=PLANE('',#42229); -#42231=ORIENTED_EDGE('',*,*,#26138,.F.); -#42233=ORIENTED_EDGE('',*,*,#42232,.T.); -#42234=ORIENTED_EDGE('',*,*,#29913,.T.); -#42235=ORIENTED_EDGE('',*,*,#42219,.F.); -#42236=EDGE_LOOP('',(#42231,#42233,#42234,#42235)); -#42237=FACE_OUTER_BOUND('',#42236,.F.); -#42239=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.074999713898E0)); -#42240=DIRECTION('',(7.975044357522E-1,0.E0,6.033130820359E-1)); -#42241=DIRECTION('',(6.033130820359E-1,0.E0,-7.975044357522E-1)); -#42242=AXIS2_PLACEMENT_3D('',#42239,#42240,#42241); -#42243=PLANE('',#42242); -#42244=ORIENTED_EDGE('',*,*,#26136,.F.); -#42246=ORIENTED_EDGE('',*,*,#42245,.T.); -#42247=ORIENTED_EDGE('',*,*,#29915,.T.); -#42248=ORIENTED_EDGE('',*,*,#42232,.F.); -#42249=EDGE_LOOP('',(#42244,#42246,#42247,#42248)); -#42250=FACE_OUTER_BOUND('',#42249,.F.); -#42252=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,1.1125E0)); -#42253=DIRECTION('',(5.065519665348E-1,0.E0,8.622094323305E-1)); -#42254=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#42255=AXIS2_PLACEMENT_3D('',#42252,#42253,#42254); -#42256=PLANE('',#42255); -#42257=ORIENTED_EDGE('',*,*,#26134,.F.); -#42259=ORIENTED_EDGE('',*,*,#42258,.T.); -#42260=ORIENTED_EDGE('',*,*,#29917,.T.); -#42261=ORIENTED_EDGE('',*,*,#42245,.F.); -#42262=EDGE_LOOP('',(#42257,#42259,#42260,#42261)); -#42263=FACE_OUTER_BOUND('',#42262,.F.); -#42265=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.131249713898E0)); -#42266=DIRECTION('',(2.818376608812E-1,0.E0,9.594621060308E-1)); -#42267=DIRECTION('',(9.594621060308E-1,0.E0,-2.818376608812E-1)); -#42268=AXIS2_PLACEMENT_3D('',#42265,#42266,#42267); -#42269=PLANE('',#42268); -#42270=ORIENTED_EDGE('',*,*,#26132,.F.); -#42272=ORIENTED_EDGE('',*,*,#42271,.T.); -#42273=ORIENTED_EDGE('',*,*,#29919,.T.); -#42274=ORIENTED_EDGE('',*,*,#42258,.F.); -#42275=EDGE_LOOP('',(#42270,#42272,#42273,#42274)); -#42276=FACE_OUTER_BOUND('',#42275,.F.); -#42278=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,1.037500286102E0)); -#42279=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42280=DIRECTION('',(0.E0,0.E0,1.E0)); -#42281=AXIS2_PLACEMENT_3D('',#42278,#42279,#42280); -#42282=PLANE('',#42281); -#42283=ORIENTED_EDGE('',*,*,#26130,.F.); -#42285=ORIENTED_EDGE('',*,*,#42284,.T.); -#42286=ORIENTED_EDGE('',*,*,#29921,.T.); -#42287=ORIENTED_EDGE('',*,*,#42271,.F.); -#42288=EDGE_LOOP('',(#42283,#42285,#42286,#42287)); -#42289=FACE_OUTER_BOUND('',#42288,.F.); -#42291=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,1.018749713898E0)); -#42292=DIRECTION('',(-4.032280761334E-1,0.E0,-9.150995129590E-1)); -#42293=DIRECTION('',(-9.150995129590E-1,0.E0,4.032280761334E-1)); -#42294=AXIS2_PLACEMENT_3D('',#42291,#42292,#42293); -#42295=PLANE('',#42294); -#42296=ORIENTED_EDGE('',*,*,#26128,.F.); -#42298=ORIENTED_EDGE('',*,*,#42297,.T.); -#42299=ORIENTED_EDGE('',*,*,#29923,.T.); -#42300=ORIENTED_EDGE('',*,*,#42284,.F.); -#42301=EDGE_LOOP('',(#42296,#42298,#42299,#42300)); -#42302=FACE_OUTER_BOUND('',#42301,.F.); -#42304=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,9.812502861023E-1)); -#42305=DIRECTION('',(-6.611504891330E-1,0.E0,-7.502533110351E-1)); -#42306=DIRECTION('',(-7.502533110351E-1,0.E0,6.611504891330E-1)); -#42307=AXIS2_PLACEMENT_3D('',#42304,#42305,#42306); -#42308=PLANE('',#42307); -#42309=ORIENTED_EDGE('',*,*,#26126,.F.); -#42311=ORIENTED_EDGE('',*,*,#42310,.T.); -#42312=ORIENTED_EDGE('',*,*,#29925,.T.); -#42313=ORIENTED_EDGE('',*,*,#42297,.F.); -#42314=EDGE_LOOP('',(#42309,#42311,#42312,#42313)); -#42315=FACE_OUTER_BOUND('',#42314,.F.); -#42317=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,9.4375E-1)); -#42318=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254208E-1)); -#42319=DIRECTION('',(-4.934765254208E-1,0.E0,8.697591154214E-1)); -#42320=AXIS2_PLACEMENT_3D('',#42317,#42318,#42319); -#42321=PLANE('',#42320); -#42322=ORIENTED_EDGE('',*,*,#26124,.F.); -#42324=ORIENTED_EDGE('',*,*,#42323,.T.); -#42325=ORIENTED_EDGE('',*,*,#29927,.T.); -#42326=ORIENTED_EDGE('',*,*,#42310,.F.); -#42327=EDGE_LOOP('',(#42322,#42324,#42325,#42326)); -#42328=FACE_OUTER_BOUND('',#42327,.F.); -#42330=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,8.499997138977E-1)); -#42331=DIRECTION('',(-9.752009016921E-1,0.E0,-2.213214886517E-1)); -#42332=DIRECTION('',(-2.213214886517E-1,0.E0,9.752009016921E-1)); -#42333=AXIS2_PLACEMENT_3D('',#42330,#42331,#42332); -#42334=PLANE('',#42333); -#42335=ORIENTED_EDGE('',*,*,#26122,.F.); -#42337=ORIENTED_EDGE('',*,*,#42336,.T.); -#42338=ORIENTED_EDGE('',*,*,#29929,.T.); -#42339=ORIENTED_EDGE('',*,*,#42323,.F.); -#42340=EDGE_LOOP('',(#42335,#42337,#42338,#42339)); -#42341=FACE_OUTER_BOUND('',#42340,.F.); -#42343=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,7.374997138977E-1)); -#42344=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42345=DIRECTION('',(0.E0,0.E0,1.E0)); -#42346=AXIS2_PLACEMENT_3D('',#42343,#42344,#42345); -#42347=PLANE('',#42346); -#42348=ORIENTED_EDGE('',*,*,#26120,.F.); -#42350=ORIENTED_EDGE('',*,*,#42349,.T.); -#42351=ORIENTED_EDGE('',*,*,#29931,.T.); -#42352=ORIENTED_EDGE('',*,*,#42336,.F.); -#42353=EDGE_LOOP('',(#42348,#42350,#42351,#42352)); -#42354=FACE_OUTER_BOUND('',#42353,.F.); -#42356=CARTESIAN_POINT('',(5.622340425849E0,1.55E0,6.437502861023E-1)); -#42357=DIRECTION('',(-9.752004643543E-1,0.E0,2.213234156683E-1)); -#42358=DIRECTION('',(2.213234156683E-1,0.E0,9.752004643543E-1)); -#42359=AXIS2_PLACEMENT_3D('',#42356,#42357,#42358); -#42360=PLANE('',#42359); -#42361=ORIENTED_EDGE('',*,*,#26118,.F.); -#42363=ORIENTED_EDGE('',*,*,#42362,.T.); -#42364=ORIENTED_EDGE('',*,*,#29933,.T.); -#42365=ORIENTED_EDGE('',*,*,#42349,.F.); -#42366=EDGE_LOOP('',(#42361,#42363,#42364,#42365)); -#42367=FACE_OUTER_BOUND('',#42366,.F.); -#42369=CARTESIAN_POINT('',(5.601063832641E0,1.55E0,6.0625E-1)); -#42370=DIRECTION('',(-8.697591154214E-1,0.E0,4.934765254207E-1)); -#42371=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#42372=AXIS2_PLACEMENT_3D('',#42369,#42370,#42371); -#42373=PLANE('',#42372); -#42374=ORIENTED_EDGE('',*,*,#26116,.F.); -#42376=ORIENTED_EDGE('',*,*,#42375,.T.); -#42377=ORIENTED_EDGE('',*,*,#29935,.T.); -#42378=ORIENTED_EDGE('',*,*,#42362,.F.); -#42379=EDGE_LOOP('',(#42374,#42376,#42377,#42378)); -#42380=FACE_OUTER_BOUND('',#42379,.F.); -#42382=CARTESIAN_POINT('',(5.558510631323E0,1.55E0,5.687497138977E-1)); -#42383=DIRECTION('',(-6.611590069362E-1,0.E0,7.502458047514E-1)); -#42384=DIRECTION('',(7.502458047514E-1,0.E0,6.611590069362E-1)); -#42385=AXIS2_PLACEMENT_3D('',#42382,#42383,#42384); -#42386=PLANE('',#42385); -#42387=ORIENTED_EDGE('',*,*,#26114,.F.); -#42389=ORIENTED_EDGE('',*,*,#42388,.T.); -#42390=ORIENTED_EDGE('',*,*,#29937,.T.); -#42391=ORIENTED_EDGE('',*,*,#42375,.F.); -#42392=EDGE_LOOP('',(#42387,#42389,#42390,#42391)); -#42393=FACE_OUTER_BOUND('',#42392,.F.); -#42395=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,5.5E-1)); -#42396=DIRECTION('',(-4.032126193069E-1,0.E0,9.151063236759E-1)); -#42397=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#42398=AXIS2_PLACEMENT_3D('',#42395,#42396,#42397); -#42399=PLANE('',#42398); -#42400=ORIENTED_EDGE('',*,*,#26112,.F.); -#42402=ORIENTED_EDGE('',*,*,#42401,.T.); -#42403=ORIENTED_EDGE('',*,*,#29939,.T.); -#42404=ORIENTED_EDGE('',*,*,#42388,.F.); -#42405=EDGE_LOOP('',(#42400,#42402,#42403,#42404)); -#42406=FACE_OUTER_BOUND('',#42405,.F.); -#42408=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,5.5E-1)); -#42409=DIRECTION('',(0.E0,0.E0,1.E0)); -#42410=DIRECTION('',(1.E0,0.E0,0.E0)); -#42411=AXIS2_PLACEMENT_3D('',#42408,#42409,#42410); -#42412=PLANE('',#42411); -#42413=ORIENTED_EDGE('',*,*,#26110,.F.); -#42415=ORIENTED_EDGE('',*,*,#42414,.T.); -#42416=ORIENTED_EDGE('',*,*,#29941,.T.); -#42417=ORIENTED_EDGE('',*,*,#42401,.F.); -#42418=EDGE_LOOP('',(#42413,#42415,#42416,#42417)); -#42419=FACE_OUTER_BOUND('',#42418,.F.); -#42421=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,5.875002861023E-1)); -#42422=DIRECTION('',(4.032202295217E-1,0.E0,9.151029704380E-1)); -#42423=DIRECTION('',(9.151029704380E-1,0.E0,-4.032202295217E-1)); -#42424=AXIS2_PLACEMENT_3D('',#42421,#42422,#42423); -#42425=PLANE('',#42424); -#42426=ORIENTED_EDGE('',*,*,#26108,.F.); -#42428=ORIENTED_EDGE('',*,*,#42427,.T.); -#42429=ORIENTED_EDGE('',*,*,#29943,.T.); -#42430=ORIENTED_EDGE('',*,*,#42414,.F.); -#42431=EDGE_LOOP('',(#42426,#42428,#42429,#42430)); -#42432=FACE_OUTER_BOUND('',#42431,.F.); -#42434=CARTESIAN_POINT('',(5.303191483021E0,1.55E0,6.437502861023E-1)); -#42435=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#42436=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#42437=AXIS2_PLACEMENT_3D('',#42434,#42435,#42436); -#42438=PLANE('',#42437); -#42439=ORIENTED_EDGE('',*,*,#26106,.F.); -#42441=ORIENTED_EDGE('',*,*,#42440,.T.); -#42442=ORIENTED_EDGE('',*,*,#29945,.T.); -#42443=ORIENTED_EDGE('',*,*,#42427,.F.); -#42444=EDGE_LOOP('',(#42439,#42441,#42442,#42443)); -#42445=FACE_OUTER_BOUND('',#42444,.F.); -#42447=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,7.562502861023E-1)); -#42448=DIRECTION('',(9.825817148807E-1,0.E0,1.858310350350E-1)); -#42449=DIRECTION('',(1.858310350350E-1,0.E0,-9.825817148807E-1)); -#42450=AXIS2_PLACEMENT_3D('',#42447,#42448,#42449); -#42451=PLANE('',#42450); -#42452=ORIENTED_EDGE('',*,*,#26104,.F.); -#42454=ORIENTED_EDGE('',*,*,#42453,.T.); -#42455=ORIENTED_EDGE('',*,*,#29947,.T.); -#42456=ORIENTED_EDGE('',*,*,#42440,.F.); -#42457=EDGE_LOOP('',(#42452,#42454,#42455,#42456)); -#42458=FACE_OUTER_BOUND('',#42457,.F.); -#42460=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,8.3125E-1)); -#42461=DIRECTION('',(1.E0,0.E0,0.E0)); -#42462=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42463=AXIS2_PLACEMENT_3D('',#42460,#42461,#42462); -#42464=PLANE('',#42463); -#42465=ORIENTED_EDGE('',*,*,#26102,.F.); -#42467=ORIENTED_EDGE('',*,*,#42466,.T.); -#42468=ORIENTED_EDGE('',*,*,#29949,.T.); -#42469=ORIENTED_EDGE('',*,*,#42453,.F.); -#42470=EDGE_LOOP('',(#42465,#42467,#42468,#42469)); -#42471=FACE_OUTER_BOUND('',#42470,.F.); -#42473=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,8.3125E-1)); -#42474=DIRECTION('',(0.E0,0.E0,1.E0)); -#42475=DIRECTION('',(1.E0,0.E0,0.E0)); -#42476=AXIS2_PLACEMENT_3D('',#42473,#42474,#42475); -#42477=PLANE('',#42476); -#42478=ORIENTED_EDGE('',*,*,#26100,.F.); -#42480=ORIENTED_EDGE('',*,*,#42479,.T.); -#42481=ORIENTED_EDGE('',*,*,#29951,.T.); -#42482=ORIENTED_EDGE('',*,*,#42466,.F.); -#42483=EDGE_LOOP('',(#42478,#42480,#42481,#42482)); -#42484=FACE_OUTER_BOUND('',#42483,.F.); -#42486=CARTESIAN_POINT('',(5.196808516979E0,1.55E0,7.562502861023E-1)); -#42487=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42488=DIRECTION('',(0.E0,0.E0,1.E0)); -#42489=AXIS2_PLACEMENT_3D('',#42486,#42487,#42488); -#42490=PLANE('',#42489); -#42491=ORIENTED_EDGE('',*,*,#26098,.F.); -#42493=ORIENTED_EDGE('',*,*,#42492,.T.); -#42494=ORIENTED_EDGE('',*,*,#29953,.T.); -#42495=ORIENTED_EDGE('',*,*,#42479,.F.); -#42496=EDGE_LOOP('',(#42491,#42493,#42494,#42495)); -#42497=FACE_OUTER_BOUND('',#42496,.F.); -#42499=CARTESIAN_POINT('',(5.154255330563E0,1.55E0,6.437502861023E-1)); -#42500=DIRECTION('',(-9.353258264754E-1,0.E0,3.537875044826E-1)); -#42501=DIRECTION('',(3.537875044826E-1,0.E0,9.353258264754E-1)); -#42502=AXIS2_PLACEMENT_3D('',#42499,#42500,#42501); -#42503=PLANE('',#42502); -#42504=ORIENTED_EDGE('',*,*,#26096,.F.); -#42506=ORIENTED_EDGE('',*,*,#42505,.T.); -#42507=ORIENTED_EDGE('',*,*,#29955,.T.); -#42508=ORIENTED_EDGE('',*,*,#42492,.F.); -#42509=EDGE_LOOP('',(#42504,#42506,#42507,#42508)); -#42510=FACE_OUTER_BOUND('',#42509,.F.); -#42512=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,6.0625E-1)); -#42513=DIRECTION('',(-6.611591372532E-1,0.E0,7.502456899087E-1)); -#42514=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#42515=AXIS2_PLACEMENT_3D('',#42512,#42513,#42514); -#42516=PLANE('',#42515); -#42517=ORIENTED_EDGE('',*,*,#26094,.F.); -#42519=ORIENTED_EDGE('',*,*,#42518,.T.); -#42520=ORIENTED_EDGE('',*,*,#29957,.T.); -#42521=ORIENTED_EDGE('',*,*,#42505,.F.); -#42522=EDGE_LOOP('',(#42517,#42519,#42520,#42521)); -#42523=FACE_OUTER_BOUND('',#42522,.F.); -#42525=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,5.687497138977E-1)); -#42526=DIRECTION('',(-4.032203477633E-1,0.E0,9.151029183374E-1)); -#42527=DIRECTION('',(9.151029183374E-1,0.E0,4.032203477633E-1)); -#42528=AXIS2_PLACEMENT_3D('',#42525,#42526,#42527); -#42529=PLANE('',#42528); -#42530=ORIENTED_EDGE('',*,*,#26092,.F.); -#42532=ORIENTED_EDGE('',*,*,#42531,.T.); -#42533=ORIENTED_EDGE('',*,*,#29959,.T.); -#42534=ORIENTED_EDGE('',*,*,#42518,.F.); -#42535=EDGE_LOOP('',(#42530,#42532,#42533,#42534)); -#42536=FACE_OUTER_BOUND('',#42535,.F.); -#42538=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,5.687497138977E-1)); -#42539=DIRECTION('',(0.E0,0.E0,1.E0)); -#42540=DIRECTION('',(1.E0,0.E0,0.E0)); -#42541=AXIS2_PLACEMENT_3D('',#42538,#42539,#42540); -#42542=PLANE('',#42541); -#42543=ORIENTED_EDGE('',*,*,#26090,.F.); -#42545=ORIENTED_EDGE('',*,*,#42544,.T.); -#42546=ORIENTED_EDGE('',*,*,#29961,.T.); -#42547=ORIENTED_EDGE('',*,*,#42531,.F.); -#42548=EDGE_LOOP('',(#42543,#42545,#42546,#42547)); -#42549=FACE_OUTER_BOUND('',#42548,.F.); -#42551=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,6.0625E-1)); -#42552=DIRECTION('',(5.065519665348E-1,0.E0,8.622094323305E-1)); -#42553=DIRECTION('',(8.622094323305E-1,0.E0,-5.065519665348E-1)); -#42554=AXIS2_PLACEMENT_3D('',#42551,#42552,#42553); -#42555=PLANE('',#42554); -#42556=ORIENTED_EDGE('',*,*,#26088,.F.); -#42558=ORIENTED_EDGE('',*,*,#42557,.T.); -#42559=ORIENTED_EDGE('',*,*,#29963,.T.); -#42560=ORIENTED_EDGE('',*,*,#42544,.F.); -#42561=EDGE_LOOP('',(#42556,#42558,#42559,#42560)); -#42562=FACE_OUTER_BOUND('',#42561,.F.); -#42564=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,6.625E-1)); -#42565=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#42566=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#42567=AXIS2_PLACEMENT_3D('',#42564,#42565,#42566); -#42568=PLANE('',#42567); -#42569=ORIENTED_EDGE('',*,*,#26086,.F.); -#42571=ORIENTED_EDGE('',*,*,#42570,.T.); -#42572=ORIENTED_EDGE('',*,*,#29965,.T.); -#42573=ORIENTED_EDGE('',*,*,#42557,.F.); -#42574=EDGE_LOOP('',(#42569,#42571,#42572,#42573)); -#42575=FACE_OUTER_BOUND('',#42574,.F.); -#42577=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,7.562502861023E-1)); -#42578=DIRECTION('',(9.752009016921E-1,0.E0,2.213214886517E-1)); -#42579=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#42580=AXIS2_PLACEMENT_3D('',#42577,#42578,#42579); -#42581=PLANE('',#42580); -#42582=ORIENTED_EDGE('',*,*,#26084,.F.); -#42584=ORIENTED_EDGE('',*,*,#42583,.T.); -#42585=ORIENTED_EDGE('',*,*,#29967,.T.); -#42586=ORIENTED_EDGE('',*,*,#42570,.F.); -#42587=EDGE_LOOP('',(#42582,#42584,#42585,#42586)); -#42588=FACE_OUTER_BOUND('',#42587,.F.); -#42590=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,8.3125E-1)); -#42591=DIRECTION('',(1.E0,0.E0,0.E0)); -#42592=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42593=AXIS2_PLACEMENT_3D('',#42590,#42591,#42592); -#42594=PLANE('',#42593); -#42595=ORIENTED_EDGE('',*,*,#26082,.F.); -#42597=ORIENTED_EDGE('',*,*,#42596,.T.); -#42598=ORIENTED_EDGE('',*,*,#29969,.T.); -#42599=ORIENTED_EDGE('',*,*,#42583,.F.); -#42600=EDGE_LOOP('',(#42595,#42597,#42598,#42599)); -#42601=FACE_OUTER_BOUND('',#42600,.F.); -#42603=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,9.250002861023E-1)); -#42604=DIRECTION('',(9.752009016921E-1,0.E0,-2.213214886517E-1)); -#42605=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#42606=AXIS2_PLACEMENT_3D('',#42603,#42604,#42605); -#42607=PLANE('',#42606); -#42608=ORIENTED_EDGE('',*,*,#26080,.F.); -#42610=ORIENTED_EDGE('',*,*,#42609,.T.); -#42611=ORIENTED_EDGE('',*,*,#29971,.T.); -#42612=ORIENTED_EDGE('',*,*,#42596,.F.); -#42613=EDGE_LOOP('',(#42608,#42610,#42611,#42612)); -#42614=FACE_OUTER_BOUND('',#42613,.F.); -#42616=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,9.812502861023E-1)); -#42617=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#42618=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#42619=AXIS2_PLACEMENT_3D('',#42616,#42617,#42618); -#42620=PLANE('',#42619); -#42621=ORIENTED_EDGE('',*,*,#26078,.F.); -#42623=ORIENTED_EDGE('',*,*,#42622,.T.); -#42624=ORIENTED_EDGE('',*,*,#29973,.T.); -#42625=ORIENTED_EDGE('',*,*,#42609,.F.); -#42626=EDGE_LOOP('',(#42621,#42623,#42624,#42625)); -#42627=FACE_OUTER_BOUND('',#42626,.F.); -#42629=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.018749713898E0)); -#42630=DIRECTION('',(5.065433474453E-1,0.E0,-8.622144960269E-1)); -#42631=DIRECTION('',(-8.622144960269E-1,0.E0,-5.065433474453E-1)); -#42632=AXIS2_PLACEMENT_3D('',#42629,#42630,#42631); -#42633=PLANE('',#42632); -#42634=ORIENTED_EDGE('',*,*,#26076,.F.); -#42636=ORIENTED_EDGE('',*,*,#42635,.T.); -#42637=ORIENTED_EDGE('',*,*,#29975,.T.); -#42638=ORIENTED_EDGE('',*,*,#42622,.F.); -#42639=EDGE_LOOP('',(#42634,#42636,#42637,#42638)); -#42640=FACE_OUTER_BOUND('',#42639,.F.); -#42642=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.1125E0)); -#42643=DIRECTION('',(1.E0,0.E0,0.E0)); -#42644=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42645=AXIS2_PLACEMENT_3D('',#42642,#42643,#42644); -#42646=PLANE('',#42645); -#42647=ORIENTED_EDGE('',*,*,#26074,.F.); -#42649=ORIENTED_EDGE('',*,*,#42648,.T.); -#42650=ORIENTED_EDGE('',*,*,#29977,.T.); -#42651=ORIENTED_EDGE('',*,*,#42635,.F.); -#42652=EDGE_LOOP('',(#42647,#42649,#42650,#42651)); -#42653=FACE_OUTER_BOUND('',#42652,.F.); -#42655=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,1.093750286102E0)); -#42656=DIRECTION('',(-2.151497590808E-1,0.E0,9.765810673812E-1)); -#42657=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#42658=AXIS2_PLACEMENT_3D('',#42655,#42656,#42657); -#42659=PLANE('',#42658); -#42660=ORIENTED_EDGE('',*,*,#26072,.F.); -#42662=ORIENTED_EDGE('',*,*,#42661,.T.); -#42663=ORIENTED_EDGE('',*,*,#29979,.T.); -#42664=ORIENTED_EDGE('',*,*,#42648,.F.); -#42665=EDGE_LOOP('',(#42660,#42662,#42663,#42664)); -#42666=FACE_OUTER_BOUND('',#42665,.F.); -#42668=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.018749713898E0)); -#42669=DIRECTION('',(-6.611591372532E-1,0.E0,7.502456899087E-1)); -#42670=DIRECTION('',(7.502456899087E-1,0.E0,6.611591372532E-1)); -#42671=AXIS2_PLACEMENT_3D('',#42668,#42669,#42670); -#42672=PLANE('',#42671); -#42673=ORIENTED_EDGE('',*,*,#26070,.F.); -#42675=ORIENTED_EDGE('',*,*,#42674,.T.); -#42676=ORIENTED_EDGE('',*,*,#29981,.T.); -#42677=ORIENTED_EDGE('',*,*,#42661,.F.); -#42678=EDGE_LOOP('',(#42673,#42675,#42676,#42677)); -#42679=FACE_OUTER_BOUND('',#42678,.F.); -#42681=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,9.4375E-1)); -#42682=DIRECTION('',(-8.697566915162E-1,0.E0,4.934807975625E-1)); -#42683=DIRECTION('',(4.934807975625E-1,0.E0,8.697566915162E-1)); -#42684=AXIS2_PLACEMENT_3D('',#42681,#42682,#42683); -#42685=PLANE('',#42684); -#42686=ORIENTED_EDGE('',*,*,#26068,.F.); -#42688=ORIENTED_EDGE('',*,*,#42687,.T.); -#42689=ORIENTED_EDGE('',*,*,#29983,.T.); -#42690=ORIENTED_EDGE('',*,*,#42674,.F.); -#42691=EDGE_LOOP('',(#42686,#42688,#42689,#42690)); -#42692=FACE_OUTER_BOUND('',#42691,.F.); -#42694=CARTESIAN_POINT('',(4.75E0,1.55E0,8.125002861023E-1)); -#42695=DIRECTION('',(-9.871139661698E-1,0.E0,1.600188044967E-1)); -#42696=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#42697=AXIS2_PLACEMENT_3D('',#42694,#42695,#42696); -#42698=PLANE('',#42697); -#42699=ORIENTED_EDGE('',*,*,#26066,.F.); -#42701=ORIENTED_EDGE('',*,*,#42700,.T.); -#42702=ORIENTED_EDGE('',*,*,#29985,.T.); -#42703=ORIENTED_EDGE('',*,*,#42687,.F.); -#42704=EDGE_LOOP('',(#42699,#42701,#42702,#42703)); -#42705=FACE_OUTER_BOUND('',#42704,.F.); -#42707=CARTESIAN_POINT('',(4.75E0,1.55E0,7.75E-1)); -#42708=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42709=DIRECTION('',(0.E0,0.E0,1.E0)); -#42710=AXIS2_PLACEMENT_3D('',#42707,#42708,#42709); -#42711=PLANE('',#42710); -#42712=ORIENTED_EDGE('',*,*,#26064,.F.); -#42714=ORIENTED_EDGE('',*,*,#42713,.T.); -#42715=ORIENTED_EDGE('',*,*,#29987,.T.); -#42716=ORIENTED_EDGE('',*,*,#42700,.F.); -#42717=EDGE_LOOP('',(#42712,#42714,#42715,#42716)); -#42718=FACE_OUTER_BOUND('',#42717,.F.); -#42720=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,6.437502861023E-1)); -#42721=DIRECTION('',(-9.871139661698E-1,0.E0,-1.600188044967E-1)); -#42722=DIRECTION('',(-1.600188044967E-1,0.E0,9.871139661698E-1)); -#42723=AXIS2_PLACEMENT_3D('',#42720,#42721,#42722); -#42724=PLANE('',#42723); -#42725=ORIENTED_EDGE('',*,*,#26062,.F.); -#42727=ORIENTED_EDGE('',*,*,#42726,.T.); -#42728=ORIENTED_EDGE('',*,*,#29989,.T.); -#42729=ORIENTED_EDGE('',*,*,#42713,.F.); -#42730=EDGE_LOOP('',(#42725,#42727,#42728,#42729)); -#42731=FACE_OUTER_BOUND('',#42730,.F.); -#42733=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,5.687497138977E-1)); -#42734=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#42735=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#42736=AXIS2_PLACEMENT_3D('',#42733,#42734,#42735); -#42737=PLANE('',#42736); -#42738=ORIENTED_EDGE('',*,*,#26060,.F.); -#42740=ORIENTED_EDGE('',*,*,#42739,.T.); -#42741=ORIENTED_EDGE('',*,*,#29991,.T.); -#42742=ORIENTED_EDGE('',*,*,#42726,.F.); -#42743=EDGE_LOOP('',(#42738,#42740,#42741,#42742)); -#42744=FACE_OUTER_BOUND('',#42743,.F.); -#42746=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,4.9375E-1)); -#42747=DIRECTION('',(-6.611548783840E-1,0.E0,-7.502494430448E-1)); -#42748=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#42749=AXIS2_PLACEMENT_3D('',#42746,#42747,#42748); -#42750=PLANE('',#42749); -#42751=ORIENTED_EDGE('',*,*,#26058,.F.); -#42753=ORIENTED_EDGE('',*,*,#42752,.T.); -#42754=ORIENTED_EDGE('',*,*,#29993,.T.); -#42755=ORIENTED_EDGE('',*,*,#42739,.F.); -#42756=EDGE_LOOP('',(#42751,#42753,#42754,#42755)); -#42757=FACE_OUTER_BOUND('',#42756,.F.); -#42759=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,4.750002861023E-1)); -#42760=DIRECTION('',(-2.151497590808E-1,0.E0,-9.765810673812E-1)); -#42761=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#42762=AXIS2_PLACEMENT_3D('',#42759,#42760,#42761); -#42763=PLANE('',#42762); -#42764=ORIENTED_EDGE('',*,*,#26056,.F.); -#42766=ORIENTED_EDGE('',*,*,#42765,.T.); -#42767=ORIENTED_EDGE('',*,*,#29995,.T.); -#42768=ORIENTED_EDGE('',*,*,#42752,.F.); -#42769=EDGE_LOOP('',(#42764,#42766,#42767,#42768)); -#42770=FACE_OUTER_BOUND('',#42769,.F.); -#42772=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,4.750002861023E-1)); -#42773=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42774=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42775=AXIS2_PLACEMENT_3D('',#42772,#42773,#42774); -#42776=PLANE('',#42775); -#42777=ORIENTED_EDGE('',*,*,#26054,.F.); -#42779=ORIENTED_EDGE('',*,*,#42778,.T.); -#42780=ORIENTED_EDGE('',*,*,#29997,.T.); -#42781=ORIENTED_EDGE('',*,*,#42765,.F.); -#42782=EDGE_LOOP('',(#42777,#42779,#42780,#42781)); -#42783=FACE_OUTER_BOUND('',#42782,.F.); -#42785=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,4.9375E-1)); -#42786=DIRECTION('',(2.151497590808E-1,0.E0,-9.765810673812E-1)); -#42787=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#42788=AXIS2_PLACEMENT_3D('',#42785,#42786,#42787); -#42789=PLANE('',#42788); -#42790=ORIENTED_EDGE('',*,*,#26052,.F.); -#42792=ORIENTED_EDGE('',*,*,#42791,.T.); -#42793=ORIENTED_EDGE('',*,*,#29999,.T.); -#42794=ORIENTED_EDGE('',*,*,#42778,.F.); -#42795=EDGE_LOOP('',(#42790,#42792,#42793,#42794)); -#42796=FACE_OUTER_BOUND('',#42795,.F.); -#42798=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,5.312502861023E-1)); -#42799=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#42800=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#42801=AXIS2_PLACEMENT_3D('',#42798,#42799,#42800); -#42802=PLANE('',#42801); -#42803=ORIENTED_EDGE('',*,*,#26050,.F.); -#42805=ORIENTED_EDGE('',*,*,#42804,.T.); -#42806=ORIENTED_EDGE('',*,*,#30001,.T.); -#42807=ORIENTED_EDGE('',*,*,#42791,.F.); -#42808=EDGE_LOOP('',(#42803,#42805,#42806,#42807)); -#42809=FACE_OUTER_BOUND('',#42808,.F.); -#42811=CARTESIAN_POINT('',(5.239361703396E0,1.55E0,6.0625E-1)); -#42812=DIRECTION('',(7.615382075403E-1,0.E0,-6.481200185586E-1)); -#42813=DIRECTION('',(-6.481200185586E-1,0.E0,-7.615382075403E-1)); -#42814=AXIS2_PLACEMENT_3D('',#42811,#42812,#42813); -#42815=PLANE('',#42814); -#42816=ORIENTED_EDGE('',*,*,#26048,.F.); -#42818=ORIENTED_EDGE('',*,*,#42817,.T.); -#42819=ORIENTED_EDGE('',*,*,#30003,.T.); -#42820=ORIENTED_EDGE('',*,*,#42804,.F.); -#42821=EDGE_LOOP('',(#42816,#42818,#42819,#42820)); -#42822=FACE_OUTER_BOUND('',#42821,.F.); -#42824=CARTESIAN_POINT('',(5.281914889812E0,1.55E0,5.124997138977E-1)); -#42825=DIRECTION('',(-9.105880073896E-1,0.E0,-4.133152317521E-1)); -#42826=DIRECTION('',(-4.133152317521E-1,0.E0,9.105880073896E-1)); -#42827=AXIS2_PLACEMENT_3D('',#42824,#42825,#42826); -#42828=PLANE('',#42827); -#42829=ORIENTED_EDGE('',*,*,#26046,.F.); -#42831=ORIENTED_EDGE('',*,*,#42830,.T.); -#42832=ORIENTED_EDGE('',*,*,#30005,.T.); -#42833=ORIENTED_EDGE('',*,*,#42817,.F.); -#42834=EDGE_LOOP('',(#42829,#42831,#42832,#42833)); -#42835=FACE_OUTER_BOUND('',#42834,.F.); -#42837=CARTESIAN_POINT('',(5.345744669437E0,1.55E0,4.750002861023E-1)); -#42838=DIRECTION('',(-5.065433474453E-1,0.E0,-8.622144960269E-1)); -#42839=DIRECTION('',(-8.622144960269E-1,0.E0,5.065433474453E-1)); -#42840=AXIS2_PLACEMENT_3D('',#42837,#42838,#42839); -#42841=PLANE('',#42840); -#42842=ORIENTED_EDGE('',*,*,#26044,.F.); -#42844=ORIENTED_EDGE('',*,*,#42843,.T.); -#42845=ORIENTED_EDGE('',*,*,#30007,.T.); -#42846=ORIENTED_EDGE('',*,*,#42830,.F.); -#42847=EDGE_LOOP('',(#42842,#42844,#42845,#42846)); -#42848=FACE_OUTER_BOUND('',#42847,.F.); -#42850=CARTESIAN_POINT('',(5.430851072073E0,1.55E0,4.562497138977E-1)); -#42851=DIRECTION('',(-2.151590802187E-1,0.E0,-9.765790138025E-1)); -#42852=DIRECTION('',(-9.765790138025E-1,0.E0,2.151590802187E-1)); -#42853=AXIS2_PLACEMENT_3D('',#42850,#42851,#42852); -#42854=PLANE('',#42853); -#42855=ORIENTED_EDGE('',*,*,#26042,.F.); -#42857=ORIENTED_EDGE('',*,*,#42856,.T.); -#42858=ORIENTED_EDGE('',*,*,#30009,.T.); -#42859=ORIENTED_EDGE('',*,*,#42843,.F.); -#42860=EDGE_LOOP('',(#42855,#42857,#42858,#42859)); -#42861=FACE_OUTER_BOUND('',#42860,.F.); -#42863=CARTESIAN_POINT('',(5.515957444906E0,1.55E0,4.562497138977E-1)); -#42864=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42865=DIRECTION('',(-1.E0,0.E0,0.E0)); -#42866=AXIS2_PLACEMENT_3D('',#42863,#42864,#42865); -#42867=PLANE('',#42866); -#42868=ORIENTED_EDGE('',*,*,#26040,.F.); -#42870=ORIENTED_EDGE('',*,*,#42869,.T.); -#42871=ORIENTED_EDGE('',*,*,#30011,.T.); -#42872=ORIENTED_EDGE('',*,*,#42856,.F.); -#42873=EDGE_LOOP('',(#42868,#42870,#42871,#42872)); -#42874=FACE_OUTER_BOUND('',#42873,.F.); -#42876=CARTESIAN_POINT('',(5.579787239432E0,1.55E0,4.750002861023E-1)); -#42877=DIRECTION('',(2.818495377036E-1,0.E0,-9.594586171880E-1)); -#42878=DIRECTION('',(-9.594586171880E-1,0.E0,-2.818495377036E-1)); -#42879=AXIS2_PLACEMENT_3D('',#42876,#42877,#42878); -#42880=PLANE('',#42879); -#42881=ORIENTED_EDGE('',*,*,#26038,.F.); -#42882=ORIENTED_EDGE('',*,*,#42156,.T.); -#42883=ORIENTED_EDGE('',*,*,#30013,.T.); -#42884=ORIENTED_EDGE('',*,*,#42869,.F.); -#42885=EDGE_LOOP('',(#42881,#42882,#42883,#42884)); -#42886=FACE_OUTER_BOUND('',#42885,.F.); -#42888=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,3.062502861023E-1)); -#42889=DIRECTION('',(0.E0,0.E0,1.E0)); -#42890=DIRECTION('',(1.E0,0.E0,0.E0)); -#42891=AXIS2_PLACEMENT_3D('',#42888,#42889,#42890); -#42892=PLANE('',#42891); -#42893=ORIENTED_EDGE('',*,*,#26152,.F.); -#42895=ORIENTED_EDGE('',*,*,#42894,.T.); -#42896=ORIENTED_EDGE('',*,*,#30030,.T.); -#42898=ORIENTED_EDGE('',*,*,#42897,.F.); -#42899=EDGE_LOOP('',(#42893,#42895,#42896,#42898)); -#42900=FACE_OUTER_BOUND('',#42899,.F.); -#42902=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-2.187502861023E-1)); -#42903=DIRECTION('',(-7.024658824885E-1,0.E0,7.117174186007E-1)); -#42904=DIRECTION('',(7.117174186007E-1,0.E0,7.024658824885E-1)); -#42905=AXIS2_PLACEMENT_3D('',#42902,#42903,#42904); -#42906=PLANE('',#42905); -#42907=ORIENTED_EDGE('',*,*,#26206,.F.); -#42909=ORIENTED_EDGE('',*,*,#42908,.T.); -#42910=ORIENTED_EDGE('',*,*,#30032,.T.); -#42911=ORIENTED_EDGE('',*,*,#42894,.F.); -#42912=EDGE_LOOP('',(#42907,#42909,#42910,#42911)); -#42913=FACE_OUTER_BOUND('',#42912,.F.); -#42915=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-2.562497138977E-1)); -#42916=DIRECTION('',(-4.032126193069E-1,0.E0,9.151063236759E-1)); -#42917=DIRECTION('',(9.151063236759E-1,0.E0,4.032126193069E-1)); -#42918=AXIS2_PLACEMENT_3D('',#42915,#42916,#42917); -#42919=PLANE('',#42918); -#42920=ORIENTED_EDGE('',*,*,#26204,.F.); -#42922=ORIENTED_EDGE('',*,*,#42921,.T.); -#42923=ORIENTED_EDGE('',*,*,#30034,.T.); -#42924=ORIENTED_EDGE('',*,*,#42908,.F.); -#42925=EDGE_LOOP('',(#42920,#42922,#42923,#42924)); -#42926=FACE_OUTER_BOUND('',#42925,.F.); -#42928=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-2.562497138977E-1)); -#42929=DIRECTION('',(0.E0,0.E0,1.E0)); -#42930=DIRECTION('',(1.E0,0.E0,0.E0)); -#42931=AXIS2_PLACEMENT_3D('',#42928,#42929,#42930); -#42932=PLANE('',#42931); -#42933=ORIENTED_EDGE('',*,*,#26202,.F.); -#42935=ORIENTED_EDGE('',*,*,#42934,.T.); -#42936=ORIENTED_EDGE('',*,*,#30036,.T.); -#42937=ORIENTED_EDGE('',*,*,#42921,.F.); -#42938=EDGE_LOOP('',(#42933,#42935,#42936,#42937)); -#42939=FACE_OUTER_BOUND('',#42938,.F.); -#42941=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,-2.187502861023E-1)); -#42942=DIRECTION('',(5.065433474453E-1,0.E0,8.622144960269E-1)); -#42943=DIRECTION('',(8.622144960269E-1,0.E0,-5.065433474453E-1)); -#42944=AXIS2_PLACEMENT_3D('',#42941,#42942,#42943); -#42945=PLANE('',#42944); -#42946=ORIENTED_EDGE('',*,*,#26200,.F.); -#42948=ORIENTED_EDGE('',*,*,#42947,.T.); -#42949=ORIENTED_EDGE('',*,*,#30038,.T.); -#42950=ORIENTED_EDGE('',*,*,#42934,.F.); -#42951=EDGE_LOOP('',(#42946,#42948,#42949,#42950)); -#42952=FACE_OUTER_BOUND('',#42951,.F.); -#42954=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,-1.625002861023E-1)); -#42955=DIRECTION('',(7.975044865771E-1,0.E0,6.033130148517E-1)); -#42956=DIRECTION('',(6.033130148517E-1,0.E0,-7.975044865771E-1)); -#42957=AXIS2_PLACEMENT_3D('',#42954,#42955,#42956); -#42958=PLANE('',#42957); -#42959=ORIENTED_EDGE('',*,*,#26198,.F.); -#42961=ORIENTED_EDGE('',*,*,#42960,.T.); -#42962=ORIENTED_EDGE('',*,*,#30040,.T.); -#42963=ORIENTED_EDGE('',*,*,#42947,.F.); -#42964=EDGE_LOOP('',(#42959,#42961,#42962,#42963)); -#42965=FACE_OUTER_BOUND('',#42964,.F.); -#42967=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,-6.875E-2)); -#42968=DIRECTION('',(9.752009016921E-1,0.E0,2.213214886517E-1)); -#42969=DIRECTION('',(2.213214886517E-1,0.E0,-9.752009016921E-1)); -#42970=AXIS2_PLACEMENT_3D('',#42967,#42968,#42969); -#42971=PLANE('',#42970); -#42972=ORIENTED_EDGE('',*,*,#26196,.F.); -#42974=ORIENTED_EDGE('',*,*,#42973,.T.); -#42975=ORIENTED_EDGE('',*,*,#30042,.T.); -#42976=ORIENTED_EDGE('',*,*,#42960,.F.); -#42977=EDGE_LOOP('',(#42972,#42974,#42975,#42976)); -#42978=FACE_OUTER_BOUND('',#42977,.F.); -#42980=CARTESIAN_POINT('',(4.856382966042E0,1.55E0,6.249713897704E-3)); -#42981=DIRECTION('',(1.E0,0.E0,0.E0)); -#42982=DIRECTION('',(0.E0,0.E0,-1.E0)); -#42983=AXIS2_PLACEMENT_3D('',#42980,#42981,#42982); -#42984=PLANE('',#42983); -#42985=ORIENTED_EDGE('',*,*,#26194,.F.); -#42987=ORIENTED_EDGE('',*,*,#42986,.T.); -#42988=ORIENTED_EDGE('',*,*,#30044,.T.); -#42989=ORIENTED_EDGE('',*,*,#42973,.F.); -#42990=EDGE_LOOP('',(#42985,#42987,#42988,#42989)); -#42991=FACE_OUTER_BOUND('',#42990,.F.); -#42993=CARTESIAN_POINT('',(4.877659559250E0,1.55E0,1.E-1)); -#42994=DIRECTION('',(9.752009016921E-1,0.E0,-2.213214886517E-1)); -#42995=DIRECTION('',(-2.213214886517E-1,0.E0,-9.752009016921E-1)); -#42996=AXIS2_PLACEMENT_3D('',#42993,#42994,#42995); -#42997=PLANE('',#42996); -#42998=ORIENTED_EDGE('',*,*,#26192,.F.); -#43000=ORIENTED_EDGE('',*,*,#42999,.T.); -#43001=ORIENTED_EDGE('',*,*,#30046,.T.); -#43002=ORIENTED_EDGE('',*,*,#42986,.F.); -#43003=EDGE_LOOP('',(#42998,#43000,#43001,#43002)); -#43004=FACE_OUTER_BOUND('',#43003,.F.); -#43006=CARTESIAN_POINT('',(4.920212745667E0,1.55E0,1.5625E-1)); -#43007=DIRECTION('',(7.975044865770E-1,0.E0,-6.033130148517E-1)); -#43008=DIRECTION('',(-6.033130148517E-1,0.E0,-7.975044865770E-1)); -#43009=AXIS2_PLACEMENT_3D('',#43006,#43007,#43008); -#43010=PLANE('',#43009); -#43011=ORIENTED_EDGE('',*,*,#26190,.F.); -#43013=ORIENTED_EDGE('',*,*,#43012,.T.); -#43014=ORIENTED_EDGE('',*,*,#30048,.T.); -#43015=ORIENTED_EDGE('',*,*,#42999,.F.); -#43016=EDGE_LOOP('',(#43011,#43013,#43014,#43015)); -#43017=FACE_OUTER_BOUND('',#43016,.F.); -#43019=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,1.937502861023E-1)); -#43020=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#43021=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#43022=AXIS2_PLACEMENT_3D('',#43019,#43020,#43021); -#43023=PLANE('',#43022); -#43024=ORIENTED_EDGE('',*,*,#26188,.F.); -#43026=ORIENTED_EDGE('',*,*,#43025,.T.); -#43027=ORIENTED_EDGE('',*,*,#30050,.T.); -#43028=ORIENTED_EDGE('',*,*,#43012,.F.); -#43029=EDGE_LOOP('',(#43024,#43026,#43027,#43028)); -#43030=FACE_OUTER_BOUND('',#43029,.F.); -#43032=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,2.874997138977E-1)); -#43033=DIRECTION('',(1.E0,0.E0,0.E0)); -#43034=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43035=AXIS2_PLACEMENT_3D('',#43032,#43033,#43034); -#43036=PLANE('',#43035); -#43037=ORIENTED_EDGE('',*,*,#26186,.F.); -#43039=ORIENTED_EDGE('',*,*,#43038,.T.); -#43040=ORIENTED_EDGE('',*,*,#30052,.T.); -#43041=ORIENTED_EDGE('',*,*,#43025,.F.); -#43042=EDGE_LOOP('',(#43037,#43039,#43040,#43041)); -#43043=FACE_OUTER_BOUND('',#43042,.F.); -#43045=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,2.6875E-1)); -#43046=DIRECTION('',(-2.151497590808E-1,0.E0,9.765810673812E-1)); -#43047=DIRECTION('',(9.765810673812E-1,0.E0,2.151497590808E-1)); -#43048=AXIS2_PLACEMENT_3D('',#43045,#43046,#43047); -#43049=PLANE('',#43048); -#43050=ORIENTED_EDGE('',*,*,#26184,.F.); -#43052=ORIENTED_EDGE('',*,*,#43051,.T.); -#43053=ORIENTED_EDGE('',*,*,#30054,.T.); -#43054=ORIENTED_EDGE('',*,*,#43038,.F.); -#43055=EDGE_LOOP('',(#43050,#43052,#43053,#43054)); -#43056=FACE_OUTER_BOUND('',#43055,.F.); -#43058=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,1.937502861023E-1)); -#43059=DIRECTION('',(-6.611548783840E-1,0.E0,7.502494430448E-1)); -#43060=DIRECTION('',(7.502494430448E-1,0.E0,6.611548783840E-1)); -#43061=AXIS2_PLACEMENT_3D('',#43058,#43059,#43060); -#43062=PLANE('',#43061); -#43063=ORIENTED_EDGE('',*,*,#26182,.F.); -#43065=ORIENTED_EDGE('',*,*,#43064,.T.); -#43066=ORIENTED_EDGE('',*,*,#30056,.T.); -#43067=ORIENTED_EDGE('',*,*,#43051,.F.); -#43068=EDGE_LOOP('',(#43063,#43065,#43066,#43067)); -#43069=FACE_OUTER_BOUND('',#43068,.F.); -#43071=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,1.187497138977E-1)); -#43072=DIRECTION('',(-8.697591154214E-1,0.E0,4.934765254207E-1)); -#43073=DIRECTION('',(4.934765254207E-1,0.E0,8.697591154214E-1)); -#43074=AXIS2_PLACEMENT_3D('',#43071,#43072,#43073); -#43075=PLANE('',#43074); -#43076=ORIENTED_EDGE('',*,*,#26180,.F.); -#43078=ORIENTED_EDGE('',*,*,#43077,.T.); -#43079=ORIENTED_EDGE('',*,*,#30058,.T.); -#43080=ORIENTED_EDGE('',*,*,#43064,.F.); -#43081=EDGE_LOOP('',(#43076,#43078,#43079,#43080)); -#43082=FACE_OUTER_BOUND('',#43081,.F.); -#43084=CARTESIAN_POINT('',(4.75E0,1.55E0,-1.25E-2)); -#43085=DIRECTION('',(-9.871139661698E-1,0.E0,1.600188044967E-1)); -#43086=DIRECTION('',(1.600188044967E-1,0.E0,9.871139661698E-1)); -#43087=AXIS2_PLACEMENT_3D('',#43084,#43085,#43086); -#43088=PLANE('',#43087); -#43089=ORIENTED_EDGE('',*,*,#26178,.F.); -#43091=ORIENTED_EDGE('',*,*,#43090,.T.); -#43092=ORIENTED_EDGE('',*,*,#30060,.T.); -#43093=ORIENTED_EDGE('',*,*,#43077,.F.); -#43094=EDGE_LOOP('',(#43089,#43091,#43092,#43093)); -#43095=FACE_OUTER_BOUND('',#43094,.F.); -#43097=CARTESIAN_POINT('',(4.75E0,1.55E0,-8.749971389771E-2)); -#43098=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43099=DIRECTION('',(0.E0,0.E0,1.E0)); -#43100=AXIS2_PLACEMENT_3D('',#43097,#43098,#43099); -#43101=PLANE('',#43100); -#43102=ORIENTED_EDGE('',*,*,#26176,.F.); -#43104=ORIENTED_EDGE('',*,*,#43103,.T.); -#43105=ORIENTED_EDGE('',*,*,#30062,.T.); -#43106=ORIENTED_EDGE('',*,*,#43090,.F.); -#43107=EDGE_LOOP('',(#43102,#43104,#43105,#43106)); -#43108=FACE_OUTER_BOUND('',#43107,.F.); -#43110=CARTESIAN_POINT('',(4.771276593208E0,1.55E0,-1.999997138977E-1)); -#43111=DIRECTION('',(-9.825817148807E-1,0.E0,-1.858310350350E-1)); -#43112=DIRECTION('',(-1.858310350350E-1,0.E0,9.825817148807E-1)); -#43113=AXIS2_PLACEMENT_3D('',#43110,#43111,#43112); -#43114=PLANE('',#43113); -#43115=ORIENTED_EDGE('',*,*,#26174,.F.); -#43117=ORIENTED_EDGE('',*,*,#43116,.T.); -#43118=ORIENTED_EDGE('',*,*,#30064,.T.); -#43119=ORIENTED_EDGE('',*,*,#43103,.F.); -#43120=EDGE_LOOP('',(#43115,#43117,#43118,#43119)); -#43121=FACE_OUTER_BOUND('',#43120,.F.); -#43123=CARTESIAN_POINT('',(4.813829779625E0,1.55E0,-2.750002861023E-1)); -#43124=DIRECTION('',(-8.697591154214E-1,0.E0,-4.934765254207E-1)); -#43125=DIRECTION('',(-4.934765254207E-1,0.E0,8.697591154214E-1)); -#43126=AXIS2_PLACEMENT_3D('',#43123,#43124,#43125); -#43127=PLANE('',#43126); -#43128=ORIENTED_EDGE('',*,*,#26172,.F.); -#43130=ORIENTED_EDGE('',*,*,#43129,.T.); -#43131=ORIENTED_EDGE('',*,*,#30066,.T.); -#43132=ORIENTED_EDGE('',*,*,#43116,.F.); -#43133=EDGE_LOOP('',(#43128,#43130,#43131,#43132)); -#43134=FACE_OUTER_BOUND('',#43133,.F.); -#43136=CARTESIAN_POINT('',(4.898936152458E0,1.55E0,-3.5E-1)); -#43137=DIRECTION('',(-6.611548783840E-1,0.E0,-7.502494430448E-1)); -#43138=DIRECTION('',(-7.502494430448E-1,0.E0,6.611548783840E-1)); -#43139=AXIS2_PLACEMENT_3D('',#43136,#43137,#43138); -#43140=PLANE('',#43139); -#43141=ORIENTED_EDGE('',*,*,#26170,.F.); -#43143=ORIENTED_EDGE('',*,*,#43142,.T.); -#43144=ORIENTED_EDGE('',*,*,#30068,.T.); -#43145=ORIENTED_EDGE('',*,*,#43129,.F.); -#43146=EDGE_LOOP('',(#43141,#43143,#43144,#43145)); -#43147=FACE_OUTER_BOUND('',#43146,.F.); -#43149=CARTESIAN_POINT('',(4.984042525291E0,1.55E0,-3.687497138977E-1)); -#43150=DIRECTION('',(-2.151497590808E-1,0.E0,-9.765810673812E-1)); -#43151=DIRECTION('',(-9.765810673812E-1,0.E0,2.151497590808E-1)); -#43152=AXIS2_PLACEMENT_3D('',#43149,#43150,#43151); -#43153=PLANE('',#43152); -#43154=ORIENTED_EDGE('',*,*,#26168,.F.); -#43156=ORIENTED_EDGE('',*,*,#43155,.T.); -#43157=ORIENTED_EDGE('',*,*,#30070,.T.); -#43158=ORIENTED_EDGE('',*,*,#43142,.F.); -#43159=EDGE_LOOP('',(#43154,#43156,#43157,#43158)); -#43160=FACE_OUTER_BOUND('',#43159,.F.); -#43162=CARTESIAN_POINT('',(5.026595771313E0,1.55E0,-3.687497138977E-1)); -#43163=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43164=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43165=AXIS2_PLACEMENT_3D('',#43162,#43163,#43164); -#43166=PLANE('',#43165); -#43167=ORIENTED_EDGE('',*,*,#26166,.F.); -#43169=ORIENTED_EDGE('',*,*,#43168,.T.); -#43170=ORIENTED_EDGE('',*,*,#30072,.T.); -#43171=ORIENTED_EDGE('',*,*,#43155,.F.); -#43172=EDGE_LOOP('',(#43167,#43169,#43170,#43171)); -#43173=FACE_OUTER_BOUND('',#43172,.F.); -#43175=CARTESIAN_POINT('',(5.111702144146E0,1.55E0,-3.5E-1)); -#43176=DIRECTION('',(2.151497590808E-1,0.E0,-9.765810673812E-1)); -#43177=DIRECTION('',(-9.765810673812E-1,0.E0,-2.151497590808E-1)); -#43178=AXIS2_PLACEMENT_3D('',#43175,#43176,#43177); -#43179=PLANE('',#43178); -#43180=ORIENTED_EDGE('',*,*,#26164,.F.); -#43182=ORIENTED_EDGE('',*,*,#43181,.T.); -#43183=ORIENTED_EDGE('',*,*,#30074,.T.); -#43184=ORIENTED_EDGE('',*,*,#43168,.F.); -#43185=EDGE_LOOP('',(#43180,#43182,#43183,#43184)); -#43186=FACE_OUTER_BOUND('',#43185,.F.); -#43188=CARTESIAN_POINT('',(5.175531923771E0,1.55E0,-3.124997138977E-1)); -#43189=DIRECTION('',(5.065519665348E-1,0.E0,-8.622094323305E-1)); -#43190=DIRECTION('',(-8.622094323305E-1,0.E0,-5.065519665348E-1)); -#43191=AXIS2_PLACEMENT_3D('',#43188,#43189,#43190); -#43192=PLANE('',#43191); -#43193=ORIENTED_EDGE('',*,*,#26162,.F.); -#43195=ORIENTED_EDGE('',*,*,#43194,.T.); -#43196=ORIENTED_EDGE('',*,*,#30076,.T.); -#43197=ORIENTED_EDGE('',*,*,#43181,.F.); -#43198=EDGE_LOOP('',(#43193,#43195,#43196,#43197)); -#43199=FACE_OUTER_BOUND('',#43198,.F.); -#43201=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,1.5625E-1)); -#43202=DIRECTION('',(7.076082458030E-1,0.E0,-7.066049606899E-1)); -#43203=DIRECTION('',(-7.066049606899E-1,0.E0,-7.076082458030E-1)); -#43204=AXIS2_PLACEMENT_3D('',#43201,#43202,#43203); -#43205=PLANE('',#43204); -#43206=ORIENTED_EDGE('',*,*,#26160,.F.); -#43208=ORIENTED_EDGE('',*,*,#43207,.T.); -#43209=ORIENTED_EDGE('',*,*,#30078,.T.); -#43210=ORIENTED_EDGE('',*,*,#43194,.F.); -#43211=EDGE_LOOP('',(#43206,#43208,#43209,#43210)); -#43212=FACE_OUTER_BOUND('',#43211,.F.); -#43214=CARTESIAN_POINT('',(5.643617019057E0,1.55E0,-3.687497138977E-1)); -#43215=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43216=DIRECTION('',(0.E0,0.E0,1.E0)); -#43217=AXIS2_PLACEMENT_3D('',#43214,#43215,#43216); -#43218=PLANE('',#43217); -#43219=ORIENTED_EDGE('',*,*,#26158,.F.); -#43221=ORIENTED_EDGE('',*,*,#43220,.T.); -#43222=ORIENTED_EDGE('',*,*,#30080,.T.); -#43223=ORIENTED_EDGE('',*,*,#43207,.F.); -#43224=EDGE_LOOP('',(#43219,#43221,#43222,#43223)); -#43225=FACE_OUTER_BOUND('',#43224,.F.); -#43227=CARTESIAN_POINT('',(5.75E0,1.55E0,-3.687497138977E-1)); -#43228=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43229=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43230=AXIS2_PLACEMENT_3D('',#43227,#43228,#43229); -#43231=PLANE('',#43230); -#43232=ORIENTED_EDGE('',*,*,#26156,.F.); -#43234=ORIENTED_EDGE('',*,*,#43233,.T.); -#43235=ORIENTED_EDGE('',*,*,#30082,.T.); -#43236=ORIENTED_EDGE('',*,*,#43220,.F.); -#43237=EDGE_LOOP('',(#43232,#43234,#43235,#43236)); -#43238=FACE_OUTER_BOUND('',#43237,.F.); -#43240=CARTESIAN_POINT('',(5.75E0,1.55E0,3.062502861023E-1)); -#43241=DIRECTION('',(1.E0,0.E0,0.E0)); -#43242=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43243=AXIS2_PLACEMENT_3D('',#43240,#43241,#43242); -#43244=PLANE('',#43243); -#43245=ORIENTED_EDGE('',*,*,#26154,.F.); -#43246=ORIENTED_EDGE('',*,*,#42897,.T.); -#43247=ORIENTED_EDGE('',*,*,#30084,.T.); -#43248=ORIENTED_EDGE('',*,*,#43233,.F.); -#43249=EDGE_LOOP('',(#43245,#43246,#43247,#43248)); -#43250=FACE_OUTER_BOUND('',#43249,.F.); -#43252=CARTESIAN_POINT('',(-2.309434639741E0,1.55E0,7.509479917553E-1)); -#43253=DIRECTION('',(1.E0,0.E0,0.E0)); -#43254=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43255=AXIS2_PLACEMENT_3D('',#43252,#43253,#43254); -#43256=PLANE('',#43255); -#43257=ORIENTED_EDGE('',*,*,#26210,.F.); -#43259=ORIENTED_EDGE('',*,*,#43258,.T.); -#43261=ORIENTED_EDGE('',*,*,#43260,.T.); -#43263=ORIENTED_EDGE('',*,*,#43262,.F.); -#43264=EDGE_LOOP('',(#43257,#43259,#43261,#43263)); -#43265=FACE_OUTER_BOUND('',#43264,.F.); -#43267=CARTESIAN_POINT('',(-3.480176327753E0,1.55E0,3.260933015718E-1)); -#43268=CARTESIAN_POINT('',(-3.459523023799E0,1.55E0,3.335882538252E-1)); -#43269=CARTESIAN_POINT('',(-3.254072757153E0,1.55E0,4.081448449824E-1)); -#43270=CARTESIAN_POINT('',(-2.863825527816E0,1.55E0,5.497630750436E-1)); -#43271=CARTESIAN_POINT('',(-2.473578298479E0,1.55E0,6.913813051047E-1)); -#43272=CARTESIAN_POINT('',(-2.268128031833E0,1.55E0,7.659378962620E-1)); -#43273=CARTESIAN_POINT('',(-2.247474727879E0,1.55E0,7.734328485153E-1)); -#43275=DIRECTION('',(0.E0,1.E0,0.E0)); -#43276=VECTOR('',#43275,1.E0); -#43277=SURFACE_OF_LINEAR_EXTRUSION('',#43274,#43276); -#43278=ORIENTED_EDGE('',*,*,#26216,.T.); -#43280=ORIENTED_EDGE('',*,*,#43279,.T.); -#43282=ORIENTED_EDGE('',*,*,#43281,.T.); -#43283=ORIENTED_EDGE('',*,*,#43258,.F.); -#43284=EDGE_LOOP('',(#43278,#43280,#43282,#43283)); -#43285=FACE_OUTER_BOUND('',#43284,.F.); -#43287=CARTESIAN_POINT('',(-2.396578567136E0,1.55E0,8.647798500532E-2)); -#43288=CARTESIAN_POINT('',(-2.407573044989E0,1.55E0,8.643666223647E-2)); -#43289=CARTESIAN_POINT('',(-2.535300585901E0,1.55E0,8.680275871221E-2)); -#43290=CARTESIAN_POINT('',(-2.774383252738E0,1.55E0,1.062811465330E-1)); -#43291=CARTESIAN_POINT('',(-3.108900823435E0,1.55E0,1.949327331270E-1)); -#43292=CARTESIAN_POINT('',(-3.326245971089E0,1.55E0,2.964126794930E-1)); -#43293=CARTESIAN_POINT('',(-3.437386172126E0,1.55E0,3.593476974370E-1)); -#43294=CARTESIAN_POINT('',(-3.446912147603E0,1.55E0,3.648255558272E-1)); -#43296=DIRECTION('',(0.E0,1.E0,0.E0)); -#43297=VECTOR('',#43296,1.E0); -#43298=SURFACE_OF_LINEAR_EXTRUSION('',#43295,#43297); -#43299=ORIENTED_EDGE('',*,*,#26214,.F.); -#43301=ORIENTED_EDGE('',*,*,#43300,.T.); -#43303=ORIENTED_EDGE('',*,*,#43302,.T.); -#43304=ORIENTED_EDGE('',*,*,#43279,.F.); -#43305=EDGE_LOOP('',(#43299,#43301,#43303,#43304)); -#43306=FACE_OUTER_BOUND('',#43305,.F.); -#43308=CARTESIAN_POINT('',(-2.276555009126E0,1.55E0,9.244512809789E-2)); -#43309=CARTESIAN_POINT('',(-2.287507999264E0,1.55E0,9.160447111621E-2)); -#43310=CARTESIAN_POINT('',(-2.311799032873E0,1.55E0,8.994007605876E-2)); -#43311=CARTESIAN_POINT('',(-2.349448326548E0,1.55E0,8.804870970072E-2)); -#43312=CARTESIAN_POINT('',(-2.389501970825E0,1.55E0,8.684238554311E-2)); -#43313=CARTESIAN_POINT('',(-2.427196299307E0,1.55E0,8.646456328047E-2)); -#43314=CARTESIAN_POINT('',(-2.451542920430E0,1.55E0,8.666407235621E-2)); -#43315=CARTESIAN_POINT('',(-2.462526100441E0,1.55E0,8.684402752506E-2)); -#43317=DIRECTION('',(0.E0,1.E0,0.E0)); -#43318=VECTOR('',#43317,1.E0); -#43319=SURFACE_OF_LINEAR_EXTRUSION('',#43316,#43318); -#43320=ORIENTED_EDGE('',*,*,#26212,.F.); -#43321=ORIENTED_EDGE('',*,*,#43262,.T.); -#43323=ORIENTED_EDGE('',*,*,#43322,.T.); -#43324=ORIENTED_EDGE('',*,*,#43300,.F.); -#43325=EDGE_LOOP('',(#43320,#43321,#43323,#43324)); -#43326=FACE_OUTER_BOUND('',#43325,.F.); -#43328=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43329=DIRECTION('',(0.E0,1.E0,0.E0)); -#43330=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43331=AXIS2_PLACEMENT_3D('',#43328,#43329,#43330); -#43332=PLANE('',#43331); -#43333=ORIENTED_EDGE('',*,*,#43260,.F.); -#43334=ORIENTED_EDGE('',*,*,#43281,.F.); -#43335=ORIENTED_EDGE('',*,*,#43302,.F.); -#43336=ORIENTED_EDGE('',*,*,#43322,.F.); -#43337=EDGE_LOOP('',(#43333,#43334,#43335,#43336)); -#43338=FACE_OUTER_BOUND('',#43337,.F.); -#43340=FILL_AREA_STYLE_COLOUR('',#17); -#43341=FILL_AREA_STYLE('',(#43340)); -#43342=SURFACE_STYLE_FILL_AREA(#43341); -#43343=SURFACE_SIDE_STYLE('',(#43342)); -#43344=SURFACE_STYLE_USAGE(.POSITIVE.,#43343); -#43345=PRESENTATION_STYLE_ASSIGNMENT((#43344)); -#43346=STYLED_ITEM('',(#43345),#43339); -#43347=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43348=DIRECTION('',(0.E0,1.E0,0.E0)); -#43349=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43350=AXIS2_PLACEMENT_3D('',#43347,#43348,#43349); -#43351=PLANE('',#43350); -#43353=ORIENTED_EDGE('',*,*,#43352,.F.); -#43355=ORIENTED_EDGE('',*,*,#43354,.F.); -#43356=EDGE_LOOP('',(#43353,#43355)); -#43357=FACE_OUTER_BOUND('',#43356,.F.); -#43359=FILL_AREA_STYLE_COLOUR('',#17); -#43360=FILL_AREA_STYLE('',(#43359)); -#43361=SURFACE_STYLE_FILL_AREA(#43360); -#43362=SURFACE_SIDE_STYLE('',(#43361)); -#43363=SURFACE_STYLE_USAGE(.POSITIVE.,#43362); -#43364=PRESENTATION_STYLE_ASSIGNMENT((#43363)); -#43365=STYLED_ITEM('',(#43364),#43358); -#43366=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43367=DIRECTION('',(0.E0,1.E0,0.E0)); -#43368=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43369=AXIS2_PLACEMENT_3D('',#43366,#43367,#43368); -#43370=PLANE('',#43369); -#43372=ORIENTED_EDGE('',*,*,#43371,.F.); -#43374=ORIENTED_EDGE('',*,*,#43373,.F.); -#43376=ORIENTED_EDGE('',*,*,#43375,.F.); -#43378=ORIENTED_EDGE('',*,*,#43377,.F.); -#43380=ORIENTED_EDGE('',*,*,#43379,.F.); -#43382=ORIENTED_EDGE('',*,*,#43381,.F.); -#43384=ORIENTED_EDGE('',*,*,#43383,.F.); -#43386=ORIENTED_EDGE('',*,*,#43385,.F.); -#43388=ORIENTED_EDGE('',*,*,#43387,.F.); -#43390=ORIENTED_EDGE('',*,*,#43389,.F.); -#43391=EDGE_LOOP('',(#43372,#43374,#43376,#43378,#43380,#43382,#43384,#43386, -#43388,#43390)); -#43392=FACE_OUTER_BOUND('',#43391,.F.); -#43394=FILL_AREA_STYLE_COLOUR('',#17); -#43395=FILL_AREA_STYLE('',(#43394)); -#43396=SURFACE_STYLE_FILL_AREA(#43395); -#43397=SURFACE_SIDE_STYLE('',(#43396)); -#43398=SURFACE_STYLE_USAGE(.POSITIVE.,#43397); -#43399=PRESENTATION_STYLE_ASSIGNMENT((#43398)); -#43400=STYLED_ITEM('',(#43399),#43393); -#43401=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43402=DIRECTION('',(0.E0,1.E0,0.E0)); -#43403=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43404=AXIS2_PLACEMENT_3D('',#43401,#43402,#43403); -#43405=PLANE('',#43404); -#43407=ORIENTED_EDGE('',*,*,#43406,.F.); -#43409=ORIENTED_EDGE('',*,*,#43408,.F.); -#43411=ORIENTED_EDGE('',*,*,#43410,.F.); -#43413=ORIENTED_EDGE('',*,*,#43412,.F.); -#43415=ORIENTED_EDGE('',*,*,#43414,.F.); -#43417=ORIENTED_EDGE('',*,*,#43416,.F.); -#43419=ORIENTED_EDGE('',*,*,#43418,.F.); -#43421=ORIENTED_EDGE('',*,*,#43420,.F.); -#43422=EDGE_LOOP('',(#43407,#43409,#43411,#43413,#43415,#43417,#43419,#43421)); -#43423=FACE_OUTER_BOUND('',#43422,.F.); -#43425=ORIENTED_EDGE('',*,*,#43424,.F.); -#43427=ORIENTED_EDGE('',*,*,#43426,.F.); -#43429=ORIENTED_EDGE('',*,*,#43428,.F.); -#43430=EDGE_LOOP('',(#43425,#43427,#43429)); -#43431=FACE_BOUND('',#43430,.F.); -#43433=FILL_AREA_STYLE_COLOUR('',#17); -#43434=FILL_AREA_STYLE('',(#43433)); -#43435=SURFACE_STYLE_FILL_AREA(#43434); -#43436=SURFACE_SIDE_STYLE('',(#43435)); -#43437=SURFACE_STYLE_USAGE(.POSITIVE.,#43436); -#43438=PRESENTATION_STYLE_ASSIGNMENT((#43437)); -#43439=STYLED_ITEM('',(#43438),#43432); -#43440=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43441=DIRECTION('',(0.E0,1.E0,0.E0)); -#43442=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43443=AXIS2_PLACEMENT_3D('',#43440,#43441,#43442); -#43444=PLANE('',#43443); -#43446=ORIENTED_EDGE('',*,*,#43445,.F.); -#43448=ORIENTED_EDGE('',*,*,#43447,.F.); -#43450=ORIENTED_EDGE('',*,*,#43449,.F.); -#43452=ORIENTED_EDGE('',*,*,#43451,.F.); -#43454=ORIENTED_EDGE('',*,*,#43453,.F.); -#43456=ORIENTED_EDGE('',*,*,#43455,.F.); -#43458=ORIENTED_EDGE('',*,*,#43457,.F.); -#43460=ORIENTED_EDGE('',*,*,#43459,.F.); -#43462=ORIENTED_EDGE('',*,*,#43461,.F.); -#43464=ORIENTED_EDGE('',*,*,#43463,.F.); -#43465=EDGE_LOOP('',(#43446,#43448,#43450,#43452,#43454,#43456,#43458,#43460, -#43462,#43464)); -#43466=FACE_OUTER_BOUND('',#43465,.F.); -#43468=FILL_AREA_STYLE_COLOUR('',#17); -#43469=FILL_AREA_STYLE('',(#43468)); -#43470=SURFACE_STYLE_FILL_AREA(#43469); -#43471=SURFACE_SIDE_STYLE('',(#43470)); -#43472=SURFACE_STYLE_USAGE(.POSITIVE.,#43471); -#43473=PRESENTATION_STYLE_ASSIGNMENT((#43472)); -#43474=STYLED_ITEM('',(#43473),#43467); -#43475=CARTESIAN_POINT('',(0.E0,1.54E0,0.E0)); -#43476=DIRECTION('',(0.E0,1.E0,0.E0)); -#43477=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43478=AXIS2_PLACEMENT_3D('',#43475,#43476,#43477); -#43479=PLANE('',#43478); -#43481=ORIENTED_EDGE('',*,*,#43480,.F.); -#43483=ORIENTED_EDGE('',*,*,#43482,.F.); -#43485=ORIENTED_EDGE('',*,*,#43484,.F.); -#43487=ORIENTED_EDGE('',*,*,#43486,.F.); -#43489=ORIENTED_EDGE('',*,*,#43488,.F.); -#43491=ORIENTED_EDGE('',*,*,#43490,.F.); -#43493=ORIENTED_EDGE('',*,*,#43492,.F.); -#43495=ORIENTED_EDGE('',*,*,#43494,.F.); -#43497=ORIENTED_EDGE('',*,*,#43496,.F.); -#43499=ORIENTED_EDGE('',*,*,#43498,.F.); -#43501=ORIENTED_EDGE('',*,*,#43500,.F.); -#43503=ORIENTED_EDGE('',*,*,#43502,.F.); -#43505=ORIENTED_EDGE('',*,*,#43504,.F.); -#43507=ORIENTED_EDGE('',*,*,#43506,.F.); -#43509=ORIENTED_EDGE('',*,*,#43508,.F.); -#43511=ORIENTED_EDGE('',*,*,#43510,.F.); -#43513=ORIENTED_EDGE('',*,*,#43512,.F.); -#43515=ORIENTED_EDGE('',*,*,#43514,.F.); -#43517=ORIENTED_EDGE('',*,*,#43516,.F.); -#43518=EDGE_LOOP('',(#43481,#43483,#43485,#43487,#43489,#43491,#43493,#43495, -#43497,#43499,#43501,#43503,#43505,#43507,#43509,#43511,#43513,#43515,#43517)); -#43519=FACE_OUTER_BOUND('',#43518,.F.); -#43521=ORIENTED_EDGE('',*,*,#43520,.F.); -#43523=ORIENTED_EDGE('',*,*,#43522,.F.); -#43525=ORIENTED_EDGE('',*,*,#43524,.F.); -#43526=EDGE_LOOP('',(#43521,#43523,#43525)); -#43527=FACE_BOUND('',#43526,.F.); -#43529=ORIENTED_EDGE('',*,*,#43528,.F.); -#43531=ORIENTED_EDGE('',*,*,#43530,.F.); -#43533=ORIENTED_EDGE('',*,*,#43532,.F.); -#43535=ORIENTED_EDGE('',*,*,#43534,.F.); -#43537=ORIENTED_EDGE('',*,*,#43536,.F.); -#43539=ORIENTED_EDGE('',*,*,#43538,.F.); -#43541=ORIENTED_EDGE('',*,*,#43540,.F.); -#43543=ORIENTED_EDGE('',*,*,#43542,.F.); -#43545=ORIENTED_EDGE('',*,*,#43544,.F.); -#43547=ORIENTED_EDGE('',*,*,#43546,.F.); -#43549=ORIENTED_EDGE('',*,*,#43548,.F.); -#43551=ORIENTED_EDGE('',*,*,#43550,.F.); -#43552=EDGE_LOOP('',(#43529,#43531,#43533,#43535,#43537,#43539,#43541,#43543, -#43545,#43547,#43549,#43551)); -#43553=FACE_BOUND('',#43552,.F.); -#43555=FILL_AREA_STYLE_COLOUR('',#17); -#43556=FILL_AREA_STYLE('',(#43555)); -#43557=SURFACE_STYLE_FILL_AREA(#43556); -#43558=SURFACE_SIDE_STYLE('',(#43557)); -#43559=SURFACE_STYLE_USAGE(.POSITIVE.,#43558); -#43560=PRESENTATION_STYLE_ASSIGNMENT((#43559)); -#43561=STYLED_ITEM('',(#43560),#43554); -#43562=CARTESIAN_POINT('',(-1.389496191562E0,1.55E0,3.787482826744E0)); -#43563=CARTESIAN_POINT('',(-1.378232068275E0,1.55E0,3.780338853499E0)); -#43564=CARTESIAN_POINT('',(-1.249196525254E0,1.55E0,3.697099546335E0)); -#43565=CARTESIAN_POINT('',(-1.022070928953E0,1.55E0,3.519467320563E0)); -#43566=CARTESIAN_POINT('',(-7.622795865223E-1,1.55E0,3.204305359310E0)); -#43567=CARTESIAN_POINT('',(-5.737617442267E-1,1.55E0,2.852856095504E0)); -#43568=CARTESIAN_POINT('',(-4.587233502244E-1,1.55E0,2.473154193031E0)); -#43569=CARTESIAN_POINT('',(-4.206251047483E-1,1.55E0,2.080943871044E0)); -#43570=CARTESIAN_POINT('',(-4.594562146907E-1,1.55E0,1.688998689711E0)); -#43571=CARTESIAN_POINT('',(-5.749895968984E-1,1.55E0,1.309952967809E0)); -#43572=CARTESIAN_POINT('',(-7.636677122414E-1,1.55E0,9.594500467100E-1)); -#43573=CARTESIAN_POINT('',(-1.023079524938E0,1.55E0,6.453710459650E-1)); -#43574=CARTESIAN_POINT('',(-1.249578313816E0,1.55E0,4.683083834030E-1)); -#43575=CARTESIAN_POINT('',(-1.378216910845E0,1.55E0,3.853791520158E-1)); -#43576=CARTESIAN_POINT('',(-1.389473710008E0,1.55E0,3.782449602728E-1)); -#43578=DIRECTION('',(0.E0,1.E0,0.E0)); -#43579=VECTOR('',#43578,1.E0); -#43580=SURFACE_OF_LINEAR_EXTRUSION('',#43577,#43579); -#43581=ORIENTED_EDGE('',*,*,#26220,.F.); -#43583=ORIENTED_EDGE('',*,*,#43582,.T.); -#43584=ORIENTED_EDGE('',*,*,#43352,.T.); -#43586=ORIENTED_EDGE('',*,*,#43585,.F.); -#43587=EDGE_LOOP('',(#43581,#43583,#43584,#43586)); -#43588=FACE_OUTER_BOUND('',#43587,.F.); -#43590=CARTESIAN_POINT('',(-1.355854930280E0,1.55E0,3.999217256483E-1)); -#43591=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43592=DIRECTION('',(0.E0,0.E0,1.E0)); -#43593=AXIS2_PLACEMENT_3D('',#43590,#43591,#43592); -#43594=PLANE('',#43593); -#43595=ORIENTED_EDGE('',*,*,#26222,.F.); -#43596=ORIENTED_EDGE('',*,*,#43585,.T.); -#43597=ORIENTED_EDGE('',*,*,#43354,.T.); -#43598=ORIENTED_EDGE('',*,*,#43582,.F.); -#43599=EDGE_LOOP('',(#43595,#43596,#43597,#43598)); -#43600=FACE_OUTER_BOUND('',#43599,.F.); -#43602=CARTESIAN_POINT('',(-2.674462348563E0,1.55E0,4.049478312834E0)); -#43603=CARTESIAN_POINT('',(-2.685284782285E0,1.55E0,4.051951362286E0)); -#43604=CARTESIAN_POINT('',(-2.723835877721E0,1.55E0,4.064950452567E0)); -#43605=CARTESIAN_POINT('',(-2.786478319988E0,1.55E0,4.111684285312E0)); -#43606=CARTESIAN_POINT('',(-2.842964704605E0,1.55E0,4.194760630358E0)); -#43607=CARTESIAN_POINT('',(-2.884363683665E0,1.55E0,4.287845204590E0)); -#43608=CARTESIAN_POINT('',(-2.914885019781E0,1.55E0,4.375596147512E0)); -#43609=CARTESIAN_POINT('',(-2.940504397788E0,1.55E0,4.455778808010E0)); -#43610=CARTESIAN_POINT('',(-2.963736274210E0,1.55E0,4.525419954314E0)); -#43611=CARTESIAN_POINT('',(-2.990108794848E0,1.55E0,4.586877566231E0)); -#43612=CARTESIAN_POINT('',(-3.022737030265E0,1.55E0,4.636243139881E0)); -#43613=CARTESIAN_POINT('',(-3.065917078232E0,1.55E0,4.670416877497E0)); -#43614=CARTESIAN_POINT('',(-3.116627615079E0,1.55E0,4.679212470761E0)); -#43615=CARTESIAN_POINT('',(-3.164716940033E0,1.55E0,4.662778200878E0)); -#43616=CARTESIAN_POINT('',(-3.207010146779E0,1.55E0,4.629197867869E0)); -#43617=CARTESIAN_POINT('',(-3.240627301698E0,1.55E0,4.585360822888E0)); -#43618=CARTESIAN_POINT('',(-3.263425109942E0,1.55E0,4.536678364466E0)); -#43619=CARTESIAN_POINT('',(-3.272148755802E0,1.55E0,4.489539165406E0)); -#43620=CARTESIAN_POINT('',(-3.263041702391E0,1.55E0,4.445753294666E0)); -#43621=CARTESIAN_POINT('',(-3.233551737216E0,1.55E0,4.418493178925E0)); -#43622=CARTESIAN_POINT('',(-3.196008723068E0,1.55E0,4.409848993101E0)); -#43623=CARTESIAN_POINT('',(-3.159630339500E0,1.55E0,4.411265909518E0)); -#43624=CARTESIAN_POINT('',(-3.135514945296E0,1.55E0,4.416309222825E0)); -#43625=CARTESIAN_POINT('',(-3.125039898605E0,1.55E0,4.418985970783E0)); -#43627=DIRECTION('',(0.E0,1.E0,0.E0)); -#43628=VECTOR('',#43627,1.E0); -#43629=SURFACE_OF_LINEAR_EXTRUSION('',#43626,#43628); -#43630=ORIENTED_EDGE('',*,*,#27002,.F.); -#43632=ORIENTED_EDGE('',*,*,#43631,.T.); -#43633=ORIENTED_EDGE('',*,*,#43520,.T.); -#43635=ORIENTED_EDGE('',*,*,#43634,.F.); -#43636=EDGE_LOOP('',(#43630,#43632,#43633,#43635)); -#43637=FACE_OUTER_BOUND('',#43636,.F.); -#43639=CARTESIAN_POINT('',(-3.187800517669E0,1.55E0,3.929594230961E0)); -#43640=CARTESIAN_POINT('',(-3.177626470124E0,1.55E0,3.933741006526E0)); -#43641=CARTESIAN_POINT('',(-3.118898938820E0,1.55E0,3.957155887774E0)); -#43642=CARTESIAN_POINT('',(-3.010566019986E0,1.55E0,3.994843097695E0)); -#43643=CARTESIAN_POINT('',(-2.859684165553E0,1.55E0,4.034330233211E0)); -#43644=CARTESIAN_POINT('',(-2.746780373681E0,1.55E0,4.054542844621E0)); -#43645=CARTESIAN_POINT('',(-2.684113998093E0,1.55E0,4.062898238491E0)); -#43646=CARTESIAN_POINT('',(-2.673215220493E0,1.55E0,4.064266758876E0)); -#43648=DIRECTION('',(0.E0,1.E0,0.E0)); -#43649=VECTOR('',#43648,1.E0); -#43650=SURFACE_OF_LINEAR_EXTRUSION('',#43647,#43649); -#43651=ORIENTED_EDGE('',*,*,#27006,.F.); -#43653=ORIENTED_EDGE('',*,*,#43652,.T.); -#43654=ORIENTED_EDGE('',*,*,#43522,.T.); -#43655=ORIENTED_EDGE('',*,*,#43631,.F.); -#43656=EDGE_LOOP('',(#43651,#43653,#43654,#43655)); -#43657=FACE_OUTER_BOUND('',#43656,.F.); -#43659=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,4.412619339018E0)); -#43660=DIRECTION('',(1.E0,0.E0,0.E0)); -#43661=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43662=AXIS2_PLACEMENT_3D('',#43659,#43660,#43661); -#43663=PLANE('',#43662); -#43664=ORIENTED_EDGE('',*,*,#27004,.F.); -#43665=ORIENTED_EDGE('',*,*,#43634,.T.); -#43666=ORIENTED_EDGE('',*,*,#43524,.T.); -#43667=ORIENTED_EDGE('',*,*,#43652,.F.); -#43668=EDGE_LOOP('',(#43664,#43665,#43666,#43667)); -#43669=FACE_OUTER_BOUND('',#43668,.F.); -#43671=CARTESIAN_POINT('',(-2.509714535467E0,1.55E0,6.120347400888E0)); -#43672=CARTESIAN_POINT('',(-2.531684939685E0,1.55E0,6.120161357913E0)); -#43673=CARTESIAN_POINT('',(-2.715124573856E0,1.55E0,6.118608011197E0)); -#43674=CARTESIAN_POINT('',(-3.060033437979E0,1.55E0,6.115687360741E0)); -#43675=CARTESIAN_POINT('',(-3.404942302102E0,1.55E0,6.112766710285E0)); -#43676=CARTESIAN_POINT('',(-3.588381936273E0,1.55E0,6.111213363570E0)); -#43677=CARTESIAN_POINT('',(-3.610352340491E0,1.55E0,6.111027320595E0)); -#43679=DIRECTION('',(0.E0,1.E0,0.E0)); -#43680=VECTOR('',#43679,1.E0); -#43681=SURFACE_OF_LINEAR_EXTRUSION('',#43678,#43680); -#43682=ORIENTED_EDGE('',*,*,#26226,.T.); -#43684=ORIENTED_EDGE('',*,*,#43683,.T.); -#43685=ORIENTED_EDGE('',*,*,#43371,.T.); -#43687=ORIENTED_EDGE('',*,*,#43686,.F.); -#43688=EDGE_LOOP('',(#43682,#43684,#43685,#43687)); -#43689=FACE_OUTER_BOUND('',#43688,.F.); -#43691=CARTESIAN_POINT('',(-3.606172938140E0,1.55E0,5.733449243352E0)); -#43692=CARTESIAN_POINT('',(-3.585599914324E0,1.55E0,5.741161828168E0)); -#43693=CARTESIAN_POINT('',(-3.403555537413E0,1.55E0,5.809408125344E0)); -#43694=CARTESIAN_POINT('',(-3.060039807406E0,1.55E0,5.938188134882E0)); -#43695=CARTESIAN_POINT('',(-2.716524077400E0,1.55E0,6.066968144419E0)); -#43696=CARTESIAN_POINT('',(-2.534479700488E0,1.55E0,6.135214441595E0)); -#43697=CARTESIAN_POINT('',(-2.513906676672E0,1.55E0,6.142927026411E0)); -#43699=DIRECTION('',(0.E0,1.E0,0.E0)); -#43700=VECTOR('',#43699,1.E0); -#43701=SURFACE_OF_LINEAR_EXTRUSION('',#43698,#43700); -#43702=ORIENTED_EDGE('',*,*,#26244,.T.); -#43704=ORIENTED_EDGE('',*,*,#43703,.T.); -#43705=ORIENTED_EDGE('',*,*,#43373,.T.); -#43706=ORIENTED_EDGE('',*,*,#43683,.F.); -#43707=EDGE_LOOP('',(#43702,#43704,#43705,#43706)); -#43708=FACE_OUTER_BOUND('',#43707,.F.); -#43710=CARTESIAN_POINT('',(-3.544453866691E0,1.55E0,5.239527664520E0)); -#43711=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43712=DIRECTION('',(0.E0,0.E0,1.E0)); -#43713=AXIS2_PLACEMENT_3D('',#43710,#43711,#43712); -#43714=PLANE('',#43713); -#43715=ORIENTED_EDGE('',*,*,#26242,.F.); -#43717=ORIENTED_EDGE('',*,*,#43716,.T.); -#43718=ORIENTED_EDGE('',*,*,#43375,.T.); -#43719=ORIENTED_EDGE('',*,*,#43703,.F.); -#43720=EDGE_LOOP('',(#43715,#43717,#43718,#43719)); -#43721=FACE_OUTER_BOUND('',#43720,.F.); -#43723=CARTESIAN_POINT('',(-1.861227771423E0,1.55E0,5.847784167963E0)); -#43724=CARTESIAN_POINT('',(-1.881891194989E0,1.55E0,5.840317160529E0)); -#43725=CARTESIAN_POINT('',(-2.172760589317E0,1.55E0,5.735207572904E0)); -#43726=CARTESIAN_POINT('',(-2.733835954406E0,1.55E0,5.532455405090E0)); -#43727=CARTESIAN_POINT('',(-3.294911319495E0,1.55E0,5.329703237275E0)); -#43728=CARTESIAN_POINT('',(-3.585780713823E0,1.55E0,5.224593649651E0)); -#43729=CARTESIAN_POINT('',(-3.606444137389E0,1.55E0,5.217126642216E0)); -#43731=DIRECTION('',(0.E0,1.E0,0.E0)); -#43732=VECTOR('',#43731,1.E0); -#43733=SURFACE_OF_LINEAR_EXTRUSION('',#43730,#43732); -#43734=ORIENTED_EDGE('',*,*,#26240,.T.); -#43736=ORIENTED_EDGE('',*,*,#43735,.T.); -#43737=ORIENTED_EDGE('',*,*,#43377,.T.); -#43738=ORIENTED_EDGE('',*,*,#43716,.F.); -#43739=EDGE_LOOP('',(#43734,#43736,#43737,#43738)); -#43740=FACE_OUTER_BOUND('',#43739,.F.); -#43742=CARTESIAN_POINT('',(-1.923218042121E0,1.55E0,6.615024988339E0)); -#43743=DIRECTION('',(1.E0,0.E0,0.E0)); -#43744=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43745=AXIS2_PLACEMENT_3D('',#43742,#43743,#43744); -#43746=PLANE('',#43745); -#43747=ORIENTED_EDGE('',*,*,#26238,.F.); -#43749=ORIENTED_EDGE('',*,*,#43748,.T.); -#43750=ORIENTED_EDGE('',*,*,#43379,.T.); -#43751=ORIENTED_EDGE('',*,*,#43735,.F.); -#43752=EDGE_LOOP('',(#43747,#43749,#43750,#43751)); -#43753=FACE_OUTER_BOUND('',#43752,.F.); -#43755=CARTESIAN_POINT('',(-2.874810490240E0,1.55E0,6.616961294258E0)); -#43756=DIRECTION('',(2.034801677748E-3,0.E0,9.999979297889E-1)); -#43757=DIRECTION('',(9.999979297889E-1,0.E0,-2.034801677748E-3)); -#43758=AXIS2_PLACEMENT_3D('',#43755,#43756,#43757); -#43759=PLANE('',#43758); -#43760=ORIENTED_EDGE('',*,*,#26236,.F.); -#43762=ORIENTED_EDGE('',*,*,#43761,.T.); -#43763=ORIENTED_EDGE('',*,*,#43381,.T.); -#43764=ORIENTED_EDGE('',*,*,#43748,.F.); -#43765=EDGE_LOOP('',(#43760,#43762,#43763,#43764)); -#43766=FACE_OUTER_BOUND('',#43765,.F.); -#43768=CARTESIAN_POINT('',(-1.861395005731E0,1.55E0,6.990377218619E0)); -#43769=CARTESIAN_POINT('',(-1.882011177097E0,1.55E0,6.982780722606E0)); -#43770=CARTESIAN_POINT('',(-2.061221843532E0,1.55E0,6.916746487206E0)); -#43771=CARTESIAN_POINT('',(-2.399027005036E0,1.55E0,6.792274512419E0)); -#43772=CARTESIAN_POINT('',(-2.736832166539E0,1.55E0,6.667802537632E0)); -#43773=CARTESIAN_POINT('',(-2.916042832974E0,1.55E0,6.601768302231E0)); -#43774=CARTESIAN_POINT('',(-2.936659004340E0,1.55E0,6.594171806218E0)); -#43776=DIRECTION('',(0.E0,1.E0,0.E0)); -#43777=VECTOR('',#43776,1.E0); -#43778=SURFACE_OF_LINEAR_EXTRUSION('',#43775,#43777); -#43779=ORIENTED_EDGE('',*,*,#26234,.T.); -#43781=ORIENTED_EDGE('',*,*,#43780,.T.); -#43782=ORIENTED_EDGE('',*,*,#43383,.T.); -#43783=ORIENTED_EDGE('',*,*,#43761,.F.); -#43784=EDGE_LOOP('',(#43779,#43781,#43782,#43783)); -#43785=FACE_OUTER_BOUND('',#43784,.F.); -#43787=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,7.489725709329E0)); -#43788=DIRECTION('',(1.E0,0.E0,0.E0)); -#43789=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43790=AXIS2_PLACEMENT_3D('',#43787,#43788,#43789); -#43791=PLANE('',#43790); -#43792=ORIENTED_EDGE('',*,*,#26232,.F.); -#43794=ORIENTED_EDGE('',*,*,#43793,.T.); -#43795=ORIENTED_EDGE('',*,*,#43385,.T.); -#43796=ORIENTED_EDGE('',*,*,#43780,.F.); -#43797=EDGE_LOOP('',(#43792,#43794,#43795,#43796)); -#43798=FACE_OUTER_BOUND('',#43797,.F.); -#43800=CARTESIAN_POINT('',(-3.606363710516E0,1.55E0,6.875775138138E0)); -#43801=CARTESIAN_POINT('',(-3.585722849623E0,1.55E0,6.883304290486E0)); -#43802=CARTESIAN_POINT('',(-3.294882387395E0,1.55E0,6.989393961859E0)); -#43803=CARTESIAN_POINT('',(-2.733842323833E0,1.55E0,7.194044152256E0)); -#43804=CARTESIAN_POINT('',(-2.172802260272E0,1.55E0,7.398694342652E0)); -#43805=CARTESIAN_POINT('',(-1.881961798044E0,1.55E0,7.504784014025E0)); -#43806=CARTESIAN_POINT('',(-1.861320937150E0,1.55E0,7.512313166373E0)); -#43808=DIRECTION('',(0.E0,1.E0,0.E0)); -#43809=VECTOR('',#43808,1.E0); -#43810=SURFACE_OF_LINEAR_EXTRUSION('',#43807,#43809); -#43811=ORIENTED_EDGE('',*,*,#26230,.T.); -#43813=ORIENTED_EDGE('',*,*,#43812,.T.); -#43814=ORIENTED_EDGE('',*,*,#43387,.T.); -#43815=ORIENTED_EDGE('',*,*,#43793,.F.); -#43816=EDGE_LOOP('',(#43811,#43813,#43814,#43815)); -#43817=FACE_OUTER_BOUND('',#43816,.F.); -#43819=CARTESIAN_POINT('',(-3.544441127836E0,1.55E0,6.111585449519E0)); -#43820=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43821=DIRECTION('',(0.E0,0.E0,1.E0)); -#43822=AXIS2_PLACEMENT_3D('',#43819,#43820,#43821); -#43823=PLANE('',#43822); -#43824=ORIENTED_EDGE('',*,*,#26228,.F.); -#43825=ORIENTED_EDGE('',*,*,#43686,.T.); -#43826=ORIENTED_EDGE('',*,*,#43389,.T.); -#43827=ORIENTED_EDGE('',*,*,#43812,.F.); -#43828=EDGE_LOOP('',(#43824,#43825,#43826,#43827)); -#43829=FACE_OUTER_BOUND('',#43828,.F.); -#43831=CARTESIAN_POINT('',(-3.304257233591E0,1.55E0,7.898174519754E0)); -#43832=CARTESIAN_POINT('',(-3.282747396648E0,1.55E0,7.902653379898E0)); -#43833=CARTESIAN_POINT('',(-3.136490201646E0,1.55E0,7.933107609892E0)); -#43834=CARTESIAN_POINT('',(-2.865485648585E0,1.55E0,7.989537209738E0)); -#43835=CARTESIAN_POINT('',(-2.594481095524E0,1.55E0,8.045966809583E0)); -#43836=CARTESIAN_POINT('',(-2.448223900522E0,1.55E0,8.076421039578E0)); -#43837=CARTESIAN_POINT('',(-2.426714063579E0,1.55E0,8.080899899721E0)); -#43839=DIRECTION('',(0.E0,1.E0,0.E0)); -#43840=VECTOR('',#43839,1.E0); -#43841=SURFACE_OF_LINEAR_EXTRUSION('',#43838,#43840); -#43842=ORIENTED_EDGE('',*,*,#27016,.T.); -#43844=ORIENTED_EDGE('',*,*,#43843,.T.); -#43845=ORIENTED_EDGE('',*,*,#43424,.T.); -#43847=ORIENTED_EDGE('',*,*,#43846,.F.); -#43848=EDGE_LOOP('',(#43842,#43844,#43845,#43847)); -#43849=FACE_OUTER_BOUND('',#43848,.F.); -#43851=CARTESIAN_POINT('',(-2.433144128044E0,1.55E0,8.343777833733E0)); -#43852=CARTESIAN_POINT('',(-2.452510610165E0,1.55E0,8.333401290776E0)); -#43853=CARTESIAN_POINT('',(-2.596624450346E0,1.55E0,8.256185230373E0)); -#43854=CARTESIAN_POINT('',(-2.865485648585E0,1.55E0,8.112129652524E0)); -#43855=CARTESIAN_POINT('',(-3.134346846825E0,1.55E0,7.968074074675E0)); -#43856=CARTESIAN_POINT('',(-3.278460687006E0,1.55E0,7.890858014272E0)); -#43857=CARTESIAN_POINT('',(-3.297827169127E0,1.55E0,7.880481471315E0)); -#43859=DIRECTION('',(0.E0,1.E0,0.E0)); -#43860=VECTOR('',#43859,1.E0); -#43861=SURFACE_OF_LINEAR_EXTRUSION('',#43858,#43860); -#43862=ORIENTED_EDGE('',*,*,#27020,.T.); -#43864=ORIENTED_EDGE('',*,*,#43863,.T.); -#43865=ORIENTED_EDGE('',*,*,#43426,.T.); -#43866=ORIENTED_EDGE('',*,*,#43843,.F.); -#43867=EDGE_LOOP('',(#43862,#43864,#43865,#43866)); -#43868=FACE_OUTER_BOUND('',#43867,.F.); -#43870=CARTESIAN_POINT('',(-2.491243574408E0,1.55E0,8.067463319291E0)); -#43871=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43872=DIRECTION('',(0.E0,0.E0,1.E0)); -#43873=AXIS2_PLACEMENT_3D('',#43870,#43871,#43872); -#43874=PLANE('',#43873); -#43875=ORIENTED_EDGE('',*,*,#27018,.F.); -#43876=ORIENTED_EDGE('',*,*,#43846,.T.); -#43877=ORIENTED_EDGE('',*,*,#43428,.T.); -#43878=ORIENTED_EDGE('',*,*,#43863,.F.); -#43879=EDGE_LOOP('',(#43875,#43876,#43877,#43878)); -#43880=FACE_OUTER_BOUND('',#43879,.F.); -#43882=CARTESIAN_POINT('',(-1.923243519831E0,1.55E0,9.242286387282E0)); -#43883=DIRECTION('',(9.999987561857E-1,0.E0,-1.577221316427E-3)); -#43884=DIRECTION('',(-1.577221316427E-3,0.E0,-9.999987561857E-1)); -#43885=AXIS2_PLACEMENT_3D('',#43882,#43883,#43884); -#43886=PLANE('',#43885); -#43887=ORIENTED_EDGE('',*,*,#26248,.F.); -#43889=ORIENTED_EDGE('',*,*,#43888,.T.); -#43890=ORIENTED_EDGE('',*,*,#43406,.T.); -#43892=ORIENTED_EDGE('',*,*,#43891,.F.); -#43893=EDGE_LOOP('',(#43887,#43889,#43890,#43892)); -#43894=FACE_OUTER_BOUND('',#43893,.F.); -#43896=CARTESIAN_POINT('',(-3.600287747243E0,1.55E0,8.191781455391E0)); -#43897=CARTESIAN_POINT('',(-3.581667961156E0,1.55E0,8.203444938557E0)); -#43898=CARTESIAN_POINT('',(-3.292850696877E0,1.55E0,8.384360835456E0)); -#43899=CARTESIAN_POINT('',(-2.733835954406E0,1.55E0,8.734529146086E0)); -#43900=CARTESIAN_POINT('',(-2.174821211935E0,1.55E0,9.084697456716E0)); -#43901=CARTESIAN_POINT('',(-1.886003947656E0,1.55E0,9.265613353614E0)); -#43902=CARTESIAN_POINT('',(-1.867384161569E0,1.55E0,9.277276836780E0)); -#43904=DIRECTION('',(0.E0,1.E0,0.E0)); -#43905=VECTOR('',#43904,1.E0); -#43906=SURFACE_OF_LINEAR_EXTRUSION('',#43903,#43905); -#43907=ORIENTED_EDGE('',*,*,#26262,.T.); -#43909=ORIENTED_EDGE('',*,*,#43908,.T.); -#43910=ORIENTED_EDGE('',*,*,#43408,.T.); -#43911=ORIENTED_EDGE('',*,*,#43888,.F.); -#43912=EDGE_LOOP('',(#43907,#43909,#43910,#43911)); -#43913=FACE_OUTER_BOUND('',#43912,.F.); -#43915=CARTESIAN_POINT('',(-3.544428388982E0,1.55E0,7.391589548398E0)); -#43916=DIRECTION('',(-1.E0,0.E0,0.E0)); -#43917=DIRECTION('',(0.E0,0.E0,1.E0)); -#43918=AXIS2_PLACEMENT_3D('',#43915,#43916,#43917); -#43919=PLANE('',#43918); -#43920=ORIENTED_EDGE('',*,*,#26260,.F.); -#43922=ORIENTED_EDGE('',*,*,#43921,.T.); -#43923=ORIENTED_EDGE('',*,*,#43410,.T.); -#43924=ORIENTED_EDGE('',*,*,#43908,.F.); -#43925=EDGE_LOOP('',(#43920,#43922,#43923,#43924)); -#43926=FACE_OUTER_BOUND('',#43925,.F.); -#43928=CARTESIAN_POINT('',(-1.857747474115E0,1.55E0,7.567064587001E0)); -#43929=CARTESIAN_POINT('',(-1.879600720778E0,1.55E0,7.564791069072E0)); -#43930=CARTESIAN_POINT('',(-2.171640829921E0,1.55E0,7.534408470339E0)); -#43931=CARTESIAN_POINT('',(-2.733867801543E0,1.55E0,7.475916790805E0)); -#43932=CARTESIAN_POINT('',(-3.296094773165E0,1.55E0,7.417425111270E0)); -#43933=CARTESIAN_POINT('',(-3.588134882308E0,1.55E0,7.387042512538E0)); -#43934=CARTESIAN_POINT('',(-3.609988128971E0,1.55E0,7.384768994608E0)); -#43936=DIRECTION('',(0.E0,1.E0,0.E0)); -#43937=VECTOR('',#43936,1.E0); -#43938=SURFACE_OF_LINEAR_EXTRUSION('',#43935,#43937); -#43939=ORIENTED_EDGE('',*,*,#26258,.T.); -#43941=ORIENTED_EDGE('',*,*,#43940,.T.); -#43942=ORIENTED_EDGE('',*,*,#43412,.T.); -#43943=ORIENTED_EDGE('',*,*,#43921,.F.); -#43944=EDGE_LOOP('',(#43939,#43941,#43942,#43943)); -#43945=FACE_OUTER_BOUND('',#43944,.F.); -#43947=CARTESIAN_POINT('',(-1.923307214104E0,1.55E0,8.187006604870E0)); -#43948=DIRECTION('',(1.E0,0.E0,0.E0)); -#43949=DIRECTION('',(0.E0,0.E0,-1.E0)); -#43950=AXIS2_PLACEMENT_3D('',#43947,#43948,#43949); -#43951=PLANE('',#43950); -#43952=ORIENTED_EDGE('',*,*,#26256,.F.); -#43954=ORIENTED_EDGE('',*,*,#43953,.T.); -#43955=ORIENTED_EDGE('',*,*,#43414,.T.); -#43956=ORIENTED_EDGE('',*,*,#43940,.F.); -#43957=EDGE_LOOP('',(#43952,#43954,#43955,#43956)); -#43958=FACE_OUTER_BOUND('',#43957,.F.); -#43960=CARTESIAN_POINT('',(-2.239917158649E0,1.55E0,8.129484858872E0)); -#43961=CARTESIAN_POINT('',(-2.218299839125E0,1.55E0,8.133412296984E0)); -#43962=CARTESIAN_POINT('',(-2.154722855273E0,1.55E0,8.144962973706E0)); -#43963=CARTESIAN_POINT('',(-2.049186207091E0,1.55E0,8.164136889039E0)); -#43964=CARTESIAN_POINT('',(-1.943649558910E0,1.55E0,8.183310804372E0)); -#43965=CARTESIAN_POINT('',(-1.880072575058E0,1.55E0,8.194861481094E0)); -#43966=CARTESIAN_POINT('',(-1.858455255534E0,1.55E0,8.198788919206E0)); -#43968=DIRECTION('',(0.E0,1.E0,0.E0)); -#43969=VECTOR('',#43968,1.E0); -#43970=SURFACE_OF_LINEAR_EXTRUSION('',#43967,#43969); -#43971=ORIENTED_EDGE('',*,*,#26254,.T.); -#43973=ORIENTED_EDGE('',*,*,#43972,.T.); -#43974=ORIENTED_EDGE('',*,*,#43416,.T.); -#43975=ORIENTED_EDGE('',*,*,#43953,.F.); -#43976=EDGE_LOOP('',(#43971,#43973,#43974,#43975)); -#43977=FACE_OUTER_BOUND('',#43976,.F.); -#43979=CARTESIAN_POINT('',(-2.177281760801E0,1.55E0,8.477445549459E0)); -#43980=DIRECTION('',(9.999782642034E-1,0.E0,6.593263280460E-3)); -#43981=DIRECTION('',(6.593263280460E-3,0.E0,-9.999782642034E-1)); -#43982=AXIS2_PLACEMENT_3D('',#43979,#43980,#43981); -#43983=PLANE('',#43982); -#43984=ORIENTED_EDGE('',*,*,#26252,.F.); -#43986=ORIENTED_EDGE('',*,*,#43985,.T.); -#43987=ORIENTED_EDGE('',*,*,#43418,.T.); -#43988=ORIENTED_EDGE('',*,*,#43972,.F.); -#43989=EDGE_LOOP('',(#43984,#43986,#43987,#43988)); -#43990=FACE_OUTER_BOUND('',#43989,.F.); -#43992=CARTESIAN_POINT('',(-1.866068226529E0,1.55E0,8.643298674399E0)); -#43993=CARTESIAN_POINT('',(-1.885457867852E0,1.55E0,8.632965471467E0)); -#43994=CARTESIAN_POINT('',(-1.947021610893E0,1.55E0,8.600156682510E0)); -#43995=CARTESIAN_POINT('',(-2.050759455650E0,1.55E0,8.544872307530E0)); -#43996=CARTESIAN_POINT('',(-2.154497300408E0,1.55E0,8.489587932551E0)); -#43997=CARTESIAN_POINT('',(-2.216061043448E0,1.55E0,8.456779143594E0)); -#43998=CARTESIAN_POINT('',(-2.235450684772E0,1.55E0,8.446445940662E0)); -#44000=DIRECTION('',(0.E0,1.E0,0.E0)); -#44001=VECTOR('',#44000,1.E0); -#44002=SURFACE_OF_LINEAR_EXTRUSION('',#43999,#44001); -#44003=ORIENTED_EDGE('',*,*,#26250,.T.); -#44004=ORIENTED_EDGE('',*,*,#43891,.T.); -#44005=ORIENTED_EDGE('',*,*,#43420,.T.); -#44006=ORIENTED_EDGE('',*,*,#43985,.F.); -#44007=EDGE_LOOP('',(#44003,#44004,#44005,#44006)); -#44008=FACE_OUTER_BOUND('',#44007,.F.); -#44010=CARTESIAN_POINT('',(-1.923192564412E0,1.55E0,1.037838840728E1)); -#44011=DIRECTION('',(1.E0,0.E0,0.E0)); -#44012=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44013=AXIS2_PLACEMENT_3D('',#44010,#44011,#44012); -#44014=PLANE('',#44013); -#44015=ORIENTED_EDGE('',*,*,#26266,.F.); -#44017=ORIENTED_EDGE('',*,*,#44016,.T.); -#44018=ORIENTED_EDGE('',*,*,#43445,.T.); -#44020=ORIENTED_EDGE('',*,*,#44019,.F.); -#44021=EDGE_LOOP('',(#44015,#44017,#44018,#44020)); -#44022=FACE_OUTER_BOUND('',#44021,.F.); -#44024=CARTESIAN_POINT('',(-3.606437060734E0,1.55E0,9.770606403298E0)); -#44025=CARTESIAN_POINT('',(-3.585771749768E0,1.55E0,9.778068185671E0)); -#44026=CARTESIAN_POINT('',(-3.294898344898E0,1.55E0,9.883096077520E0)); -#44027=CARTESIAN_POINT('',(-2.733816846124E0,1.55E0,1.008569007885E1)); -#44028=CARTESIAN_POINT('',(-2.172735347350E0,1.55E0,1.028828408017E1)); -#44029=CARTESIAN_POINT('',(-1.881861942480E0,1.55E0,1.039331197202E1)); -#44030=CARTESIAN_POINT('',(-1.861196631514E0,1.55E0,1.040077375439E1)); -#44032=DIRECTION('',(0.E0,1.E0,0.E0)); -#44033=VECTOR('',#44032,1.E0); -#44034=SURFACE_OF_LINEAR_EXTRUSION('',#44031,#44033); -#44035=ORIENTED_EDGE('',*,*,#26284,.T.); -#44037=ORIENTED_EDGE('',*,*,#44036,.T.); -#44038=ORIENTED_EDGE('',*,*,#43447,.T.); -#44039=ORIENTED_EDGE('',*,*,#44016,.F.); -#44040=EDGE_LOOP('',(#44035,#44037,#44038,#44039)); -#44041=FACE_OUTER_BOUND('',#44040,.F.); -#44043=CARTESIAN_POINT('',(-3.543727751972E0,1.55E0,8.534948739698E0)); -#44044=DIRECTION('',(-9.999998392260E-1,0.E0,-5.670519560586E-4)); -#44045=DIRECTION('',(-5.670519560586E-4,0.E0,9.999998392260E-1)); -#44046=AXIS2_PLACEMENT_3D('',#44043,#44044,#44045); -#44047=PLANE('',#44046); -#44048=ORIENTED_EDGE('',*,*,#26282,.F.); -#44050=ORIENTED_EDGE('',*,*,#44049,.T.); -#44051=ORIENTED_EDGE('',*,*,#43449,.T.); -#44052=ORIENTED_EDGE('',*,*,#44036,.F.); -#44053=EDGE_LOOP('',(#44048,#44050,#44051,#44052)); -#44054=FACE_OUTER_BOUND('',#44053,.F.); -#44056=CARTESIAN_POINT('',(-3.095124073339E0,1.55E0,8.700737055714E0)); -#44057=CARTESIAN_POINT('',(-3.115732930474E0,1.55E0,8.693120738947E0)); -#44058=CARTESIAN_POINT('',(-3.200804638813E0,1.55E0,8.661681194561E0)); -#44059=CARTESIAN_POINT('',(-3.350339198358E0,1.55E0,8.606418422555E0)); -#44060=CARTESIAN_POINT('',(-3.499873757902E0,1.55E0,8.551155650550E0)); -#44061=CARTESIAN_POINT('',(-3.584945466241E0,1.55E0,8.519716106164E0)); -#44062=CARTESIAN_POINT('',(-3.605554323376E0,1.55E0,8.512099789396E0)); -#44064=DIRECTION('',(0.E0,1.E0,0.E0)); -#44065=VECTOR('',#44064,1.E0); -#44066=SURFACE_OF_LINEAR_EXTRUSION('',#44063,#44065); -#44067=ORIENTED_EDGE('',*,*,#26280,.T.); -#44069=ORIENTED_EDGE('',*,*,#44068,.T.); -#44070=ORIENTED_EDGE('',*,*,#43451,.T.); -#44071=ORIENTED_EDGE('',*,*,#44049,.F.); -#44072=EDGE_LOOP('',(#44067,#44069,#44070,#44071)); -#44073=FACE_OUTER_BOUND('',#44072,.F.); -#44075=CARTESIAN_POINT('',(-3.156950644744E0,1.55E0,9.305944961207E0)); -#44076=DIRECTION('',(1.E0,0.E0,0.E0)); -#44077=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44078=AXIS2_PLACEMENT_3D('',#44075,#44076,#44077); -#44079=PLANE('',#44078); -#44080=ORIENTED_EDGE('',*,*,#26278,.F.); -#44082=ORIENTED_EDGE('',*,*,#44081,.T.); -#44083=ORIENTED_EDGE('',*,*,#43453,.T.); -#44084=ORIENTED_EDGE('',*,*,#44068,.F.); -#44085=EDGE_LOOP('',(#44080,#44082,#44083,#44084)); -#44086=FACE_OUTER_BOUND('',#44085,.F.); -#44088=CARTESIAN_POINT('',(-2.856350283794E0,1.55E0,9.426549896316E0)); -#44089=CARTESIAN_POINT('',(-2.876741479245E0,1.55E0,9.418368672593E0)); -#44090=CARTESIAN_POINT('',(-2.937037137128E0,1.55E0,9.394177238213E0)); -#44091=CARTESIAN_POINT('',(-3.037237257444E0,1.55E0,9.353975593177E0)); -#44092=CARTESIAN_POINT('',(-3.137437377761E0,1.55E0,9.313773948140E0)); -#44093=CARTESIAN_POINT('',(-3.197733035644E0,1.55E0,9.289582513761E0)); -#44094=CARTESIAN_POINT('',(-3.218124231095E0,1.55E0,9.281401290038E0)); -#44096=DIRECTION('',(0.E0,1.E0,0.E0)); -#44097=VECTOR('',#44096,1.E0); -#44098=SURFACE_OF_LINEAR_EXTRUSION('',#44095,#44097); -#44099=ORIENTED_EDGE('',*,*,#26276,.T.); -#44101=ORIENTED_EDGE('',*,*,#44100,.T.); -#44102=ORIENTED_EDGE('',*,*,#43455,.T.); -#44103=ORIENTED_EDGE('',*,*,#44081,.F.); -#44104=EDGE_LOOP('',(#44099,#44101,#44102,#44103)); -#44105=FACE_OUTER_BOUND('',#44104,.F.); -#44107=CARTESIAN_POINT('',(-2.917523870145E0,1.55E0,8.815613659747E0)); -#44108=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44109=DIRECTION('',(0.E0,0.E0,1.E0)); -#44110=AXIS2_PLACEMENT_3D('',#44107,#44108,#44109); -#44111=PLANE('',#44110); -#44112=ORIENTED_EDGE('',*,*,#26274,.F.); -#44114=ORIENTED_EDGE('',*,*,#44113,.T.); -#44115=ORIENTED_EDGE('',*,*,#43457,.T.); -#44116=ORIENTED_EDGE('',*,*,#44100,.F.); -#44117=EDGE_LOOP('',(#44112,#44114,#44115,#44116)); -#44118=FACE_OUTER_BOUND('',#44117,.F.); -#44120=CARTESIAN_POINT('',(-2.509606336772E0,1.55E0,8.962944758541E0)); -#44121=CARTESIAN_POINT('',(-2.530270981191E0,1.55E0,8.955481130431E0)); -#44122=CARTESIAN_POINT('',(-2.608589558962E0,1.55E0,8.927194133244E0)); -#44123=CARTESIAN_POINT('',(-2.744562070086E0,1.55E0,8.878083766980E0)); -#44124=CARTESIAN_POINT('',(-2.880534581211E0,1.55E0,8.828973400715E0)); -#44125=CARTESIAN_POINT('',(-2.958853158982E0,1.55E0,8.800686403528E0)); -#44126=CARTESIAN_POINT('',(-2.979517803401E0,1.55E0,8.793222775419E0)); -#44128=DIRECTION('',(0.E0,1.E0,0.E0)); -#44129=VECTOR('',#44128,1.E0); -#44130=SURFACE_OF_LINEAR_EXTRUSION('',#44127,#44129); -#44131=ORIENTED_EDGE('',*,*,#26272,.T.); -#44133=ORIENTED_EDGE('',*,*,#44132,.T.); -#44134=ORIENTED_EDGE('',*,*,#43459,.T.); -#44135=ORIENTED_EDGE('',*,*,#44113,.F.); -#44136=EDGE_LOOP('',(#44131,#44133,#44134,#44135)); -#44137=FACE_OUTER_BOUND('',#44136,.F.); -#44139=CARTESIAN_POINT('',(-2.571600270028E0,1.55E0,9.528323510344E0)); -#44140=DIRECTION('',(1.E0,0.E0,0.E0)); -#44141=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44142=AXIS2_PLACEMENT_3D('',#44139,#44140,#44141); -#44143=PLANE('',#44142); -#44144=ORIENTED_EDGE('',*,*,#26270,.F.); -#44146=ORIENTED_EDGE('',*,*,#44145,.T.); -#44147=ORIENTED_EDGE('',*,*,#43461,.T.); -#44148=ORIENTED_EDGE('',*,*,#44132,.F.); -#44149=EDGE_LOOP('',(#44144,#44146,#44147,#44148)); -#44150=FACE_OUTER_BOUND('',#44149,.F.); -#44152=CARTESIAN_POINT('',(-1.861319816487E0,1.55E0,9.789183706792E0)); -#44153=CARTESIAN_POINT('',(-1.881944065795E0,1.55E0,9.781609169580E0)); -#44154=CARTESIAN_POINT('',(-2.010636266040E0,1.55E0,9.734345201566E0)); -#44155=CARTESIAN_POINT('',(-2.247396417220E0,1.55E0,9.647391802750E0)); -#44156=CARTESIAN_POINT('',(-2.484156568400E0,1.55E0,9.560438403934E0)); -#44157=CARTESIAN_POINT('',(-2.612848768644E0,1.55E0,9.513174435920E0)); -#44158=CARTESIAN_POINT('',(-2.633473017952E0,1.55E0,9.505599898709E0)); -#44160=DIRECTION('',(0.E0,1.E0,0.E0)); -#44161=VECTOR('',#44160,1.E0); -#44162=SURFACE_OF_LINEAR_EXTRUSION('',#44159,#44161); -#44163=ORIENTED_EDGE('',*,*,#26268,.T.); -#44164=ORIENTED_EDGE('',*,*,#44019,.T.); -#44165=ORIENTED_EDGE('',*,*,#43463,.T.); -#44166=ORIENTED_EDGE('',*,*,#44145,.F.); -#44167=EDGE_LOOP('',(#44163,#44164,#44165,#44166)); -#44168=FACE_OUTER_BOUND('',#44167,.F.); -#44170=CARTESIAN_POINT('',(-1.553897644718E0,1.55E0,2.888475891570E-1)); -#44171=CARTESIAN_POINT('',(-1.563776943451E0,1.55E0,2.840423201853E-1)); -#44172=CARTESIAN_POINT('',(-1.610118094645E0,1.55E0,2.619506449218E-1)); -#44173=CARTESIAN_POINT('',(-1.693965805827E0,1.55E0,2.257354205418E-1)); -#44174=CARTESIAN_POINT('',(-1.807475495311E0,1.55E0,1.846964118506E-1)); -#44175=CARTESIAN_POINT('',(-1.895094843040E0,1.55E0,1.589182427116E-1)); -#44176=CARTESIAN_POINT('',(-1.944847438686E0,1.55E0,1.462673304933E-1)); -#44177=CARTESIAN_POINT('',(-1.955513835391E0,1.55E0,1.436441557568E-1)); -#44179=DIRECTION('',(0.E0,1.E0,0.E0)); -#44180=VECTOR('',#44179,1.E0); -#44181=SURFACE_OF_LINEAR_EXTRUSION('',#44178,#44180); -#44182=ORIENTED_EDGE('',*,*,#26288,.F.); -#44184=ORIENTED_EDGE('',*,*,#44183,.T.); -#44185=ORIENTED_EDGE('',*,*,#43480,.T.); -#44187=ORIENTED_EDGE('',*,*,#44186,.F.); -#44188=EDGE_LOOP('',(#44182,#44184,#44185,#44187)); -#44189=FACE_OUTER_BOUND('',#44188,.F.); -#44191=CARTESIAN_POINT('',(-1.583651130512E0,1.55E0,1.043163682004E1)); -#44192=DIRECTION('',(1.E0,0.E0,0.E0)); -#44193=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44194=AXIS2_PLACEMENT_3D('',#44191,#44192,#44193); -#44195=PLANE('',#44194); -#44196=ORIENTED_EDGE('',*,*,#26324,.F.); -#44198=ORIENTED_EDGE('',*,*,#44197,.T.); -#44199=ORIENTED_EDGE('',*,*,#43482,.T.); -#44200=ORIENTED_EDGE('',*,*,#44183,.F.); -#44201=EDGE_LOOP('',(#44196,#44198,#44199,#44200)); -#44202=FACE_OUTER_BOUND('',#44201,.F.); -#44204=CARTESIAN_POINT('',(-1.860541233161E0,1.55E0,1.039194972842E1)); -#44205=CARTESIAN_POINT('',(-1.838792309757E0,1.55E0,1.039506703564E1)); -#44206=CARTESIAN_POINT('',(-1.781769497614E0,1.55E0,1.040324020452E1)); -#44207=CARTESIAN_POINT('',(-1.689472796731E0,1.55E0,1.041646923506E1)); -#44208=CARTESIAN_POINT('',(-1.597176095849E0,1.55E0,1.042969826559E1)); -#44209=CARTESIAN_POINT('',(-1.540153283706E0,1.55E0,1.043787143447E1)); -#44210=CARTESIAN_POINT('',(-1.518404360302E0,1.55E0,1.044098874169E1)); -#44212=DIRECTION('',(0.E0,1.E0,0.E0)); -#44213=VECTOR('',#44212,1.E0); -#44214=SURFACE_OF_LINEAR_EXTRUSION('',#44211,#44213); -#44215=ORIENTED_EDGE('',*,*,#26322,.T.); -#44217=ORIENTED_EDGE('',*,*,#44216,.T.); -#44218=ORIENTED_EDGE('',*,*,#43484,.T.); -#44219=ORIENTED_EDGE('',*,*,#44197,.F.); -#44220=EDGE_LOOP('',(#44215,#44217,#44218,#44219)); -#44221=FACE_OUTER_BOUND('',#44220,.F.); -#44223=CARTESIAN_POINT('',(-1.795294462950E0,1.55E0,3.975679865447E0)); -#44224=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44225=DIRECTION('',(0.E0,0.E0,1.E0)); -#44226=AXIS2_PLACEMENT_3D('',#44223,#44224,#44225); -#44227=PLANE('',#44226); -#44228=ORIENTED_EDGE('',*,*,#26320,.F.); -#44230=ORIENTED_EDGE('',*,*,#44229,.T.); -#44231=ORIENTED_EDGE('',*,*,#43486,.T.); -#44232=ORIENTED_EDGE('',*,*,#44216,.F.); -#44233=EDGE_LOOP('',(#44228,#44230,#44231,#44232)); -#44234=FACE_OUTER_BOUND('',#44233,.F.); -#44236=CARTESIAN_POINT('',(-2.443336081977E0,1.55E0,4.079218330546E0)); -#44237=CARTESIAN_POINT('',(-2.432347935132E0,1.55E0,4.079236501804E0)); -#44238=CARTESIAN_POINT('',(-2.351109270456E0,1.55E0,4.078782607641E0)); -#44239=CARTESIAN_POINT('',(-2.201678909058E0,1.55E0,4.069780563810E0)); -#44240=CARTESIAN_POINT('',(-1.995544695180E0,1.55E0,4.035143162476E0)); -#44241=CARTESIAN_POINT('',(-1.851381950045E0,1.55E0,3.994812156341E0)); -#44242=CARTESIAN_POINT('',(-1.774459577689E0,1.55E0,3.968690448621E0)); -#44243=CARTESIAN_POINT('',(-1.764083910845E0,1.55E0,3.965083049072E0)); -#44245=DIRECTION('',(0.E0,1.E0,0.E0)); -#44246=VECTOR('',#44245,1.E0); -#44247=SURFACE_OF_LINEAR_EXTRUSION('',#44244,#44246); -#44248=ORIENTED_EDGE('',*,*,#26318,.F.); -#44250=ORIENTED_EDGE('',*,*,#44249,.T.); -#44251=ORIENTED_EDGE('',*,*,#43488,.T.); -#44252=ORIENTED_EDGE('',*,*,#44229,.F.); -#44253=EDGE_LOOP('',(#44248,#44250,#44251,#44252)); -#44254=FACE_OUTER_BOUND('',#44253,.F.); -#44256=CARTESIAN_POINT('',(-2.422545173927E0,1.55E0,5.554095565776E0)); -#44257=CARTESIAN_POINT('',(-2.412126885362E0,1.55E0,5.557650036599E0)); -#44258=CARTESIAN_POINT('',(-2.364933551604E0,1.55E0,5.573297441197E0)); -#44259=CARTESIAN_POINT('',(-2.288186642157E0,1.55E0,5.595380433702E0)); -#44260=CARTESIAN_POINT('',(-2.195357407806E0,1.55E0,5.616171505428E0)); -#44261=CARTESIAN_POINT('',(-2.111831957201E0,1.55E0,5.615418602152E0)); -#44262=CARTESIAN_POINT('',(-2.034076197603E0,1.55E0,5.584015125337E0)); -#44263=CARTESIAN_POINT('',(-1.972781047368E0,1.55E0,5.522551309388E0)); -#44264=CARTESIAN_POINT('',(-1.928054092846E0,1.55E0,5.439259103573E0)); -#44265=CARTESIAN_POINT('',(-1.899213171976E0,1.55E0,5.342449947031E0)); -#44266=CARTESIAN_POINT('',(-1.881113379202E0,1.55E0,5.230631831318E0)); -#44267=CARTESIAN_POINT('',(-1.872089472513E0,1.55E0,5.108584671973E0)); -#44268=CARTESIAN_POINT('',(-1.870102284188E0,1.55E0,4.971852350578E0)); -#44269=CARTESIAN_POINT('',(-1.877519906028E0,1.55E0,4.821002474585E0)); -#44270=CARTESIAN_POINT('',(-1.904720895203E0,1.55E0,4.652729311598E0)); -#44271=CARTESIAN_POINT('',(-1.965755743454E0,1.55E0,4.476901127391E0)); -#44272=CARTESIAN_POINT('',(-2.068548958876E0,1.55E0,4.310937031155E0)); -#44273=CARTESIAN_POINT('',(-2.217764594764E0,1.55E0,4.168967262148E0)); -#44274=CARTESIAN_POINT('',(-2.352383278675E0,1.55E0,4.101358231971E0)); -#44275=CARTESIAN_POINT('',(-2.430795239267E0,1.55E0,4.070965197545E0)); -#44276=CARTESIAN_POINT('',(-2.441048494023E0,1.55E0,4.067121309826E0)); -#44278=DIRECTION('',(0.E0,1.E0,0.E0)); -#44279=VECTOR('',#44278,1.E0); -#44280=SURFACE_OF_LINEAR_EXTRUSION('',#44277,#44279); -#44281=ORIENTED_EDGE('',*,*,#26316,.F.); -#44283=ORIENTED_EDGE('',*,*,#44282,.T.); -#44284=ORIENTED_EDGE('',*,*,#43490,.T.); -#44285=ORIENTED_EDGE('',*,*,#44249,.F.); -#44286=EDGE_LOOP('',(#44281,#44283,#44284,#44285)); -#44287=FACE_OUTER_BOUND('',#44286,.F.); -#44289=CARTESIAN_POINT('',(-2.391205348235E0,1.55E0,4.961181115669E0)); -#44290=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44291=DIRECTION('',(0.E0,0.E0,1.E0)); -#44292=AXIS2_PLACEMENT_3D('',#44289,#44290,#44291); -#44293=PLANE('',#44292); -#44294=ORIENTED_EDGE('',*,*,#26314,.F.); -#44296=ORIENTED_EDGE('',*,*,#44295,.T.); -#44297=ORIENTED_EDGE('',*,*,#43492,.T.); -#44298=ORIENTED_EDGE('',*,*,#44282,.F.); -#44299=EDGE_LOOP('',(#44294,#44296,#44297,#44298)); -#44300=FACE_OUTER_BOUND('',#44299,.F.); -#44302=CARTESIAN_POINT('',(-3.122190003142E0,1.55E0,3.856352554656E0)); -#44303=CARTESIAN_POINT('',(-3.133794827161E0,1.55E0,3.853027887770E0)); -#44304=CARTESIAN_POINT('',(-3.184897156699E0,1.55E0,3.838904132338E0)); -#44305=CARTESIAN_POINT('',(-3.267617117925E0,1.55E0,3.822281418096E0)); -#44306=CARTESIAN_POINT('',(-3.370278241467E0,1.55E0,3.826282414398E0)); -#44307=CARTESIAN_POINT('',(-3.453260400186E0,1.55E0,3.867724004155E0)); -#44308=CARTESIAN_POINT('',(-3.511026376279E0,1.55E0,3.940034077793E0)); -#44309=CARTESIAN_POINT('',(-3.550364059428E0,1.55E0,4.029588719334E0)); -#44310=CARTESIAN_POINT('',(-3.577434871114E0,1.55E0,4.137522770088E0)); -#44311=CARTESIAN_POINT('',(-3.592297876928E0,1.55E0,4.257412996233E0)); -#44312=CARTESIAN_POINT('',(-3.597137623280E0,1.55E0,4.394677155528E0)); -#44313=CARTESIAN_POINT('',(-3.591459875117E0,1.55E0,4.548170182436E0)); -#44314=CARTESIAN_POINT('',(-3.565880503959E0,1.55E0,4.725559501087E0)); -#44315=CARTESIAN_POINT('',(-3.504733918915E0,1.55E0,4.906399271463E0)); -#44316=CARTESIAN_POINT('',(-3.404203980925E0,1.55E0,5.067285385785E0)); -#44317=CARTESIAN_POINT('',(-3.277927727304E0,1.55E0,5.184843953642E0)); -#44318=CARTESIAN_POINT('',(-3.146454375608E0,1.55E0,5.266292111941E0)); -#44319=CARTESIAN_POINT('',(-3.021323460579E0,1.55E0,5.318959135186E0)); -#44320=CARTESIAN_POINT('',(-2.902969091898E0,1.55E0,5.346238958632E0)); -#44321=CARTESIAN_POINT('',(-2.793470908436E0,1.55E0,5.335332773683E0)); -#44322=CARTESIAN_POINT('',(-2.706455277582E0,1.55E0,5.280752382903E0)); -#44323=CARTESIAN_POINT('',(-2.647376471162E0,1.55E0,5.200835725455E0)); -#44324=CARTESIAN_POINT('',(-2.606034861335E0,1.55E0,5.109276993079E0)); -#44325=CARTESIAN_POINT('',(-2.577408899502E0,1.55E0,5.016216268724E0)); -#44326=CARTESIAN_POINT('',(-2.552947439405E0,1.55E0,4.928707344134E0)); -#44327=CARTESIAN_POINT('',(-2.528912753293E0,1.55E0,4.853786914811E0)); -#44328=CARTESIAN_POINT('',(-2.500086764451E0,1.55E0,4.789120278580E0)); -#44329=CARTESIAN_POINT('',(-2.463120703018E0,1.55E0,4.738216599066E0)); -#44330=CARTESIAN_POINT('',(-2.410785388690E0,1.55E0,4.708244416815E0)); -#44331=CARTESIAN_POINT('',(-2.352252012731E0,1.55E0,4.707222226833E0)); -#44332=CARTESIAN_POINT('',(-2.297253761183E0,1.55E0,4.727364871983E0)); -#44333=CARTESIAN_POINT('',(-2.249156763479E0,1.55E0,4.760285720910E0)); -#44334=CARTESIAN_POINT('',(-2.212441387626E0,1.55E0,4.800791762064E0)); -#44335=CARTESIAN_POINT('',(-2.188882518371E0,1.55E0,4.843663234200E0)); -#44336=CARTESIAN_POINT('',(-2.176387898204E0,1.55E0,4.885152520707E0)); -#44337=CARTESIAN_POINT('',(-2.174846630662E0,1.55E0,4.924165320916E0)); -#44338=CARTESIAN_POINT('',(-2.185509917337E0,1.55E0,4.957357257822E0)); -#44339=CARTESIAN_POINT('',(-2.207120652336E0,1.55E0,4.981741170427E0)); -#44340=CARTESIAN_POINT('',(-2.237930535033E0,1.55E0,4.992162334842E0)); -#44341=CARTESIAN_POINT('',(-2.272095552519E0,1.55E0,4.991007103051E0)); -#44342=CARTESIAN_POINT('',(-2.308504002543E0,1.55E0,4.982975727737E0)); -#44343=CARTESIAN_POINT('',(-2.348530748896E0,1.55E0,4.972754816942E0)); -#44344=CARTESIAN_POINT('',(-2.388100531370E0,1.55E0,4.962124408681E0)); -#44345=CARTESIAN_POINT('',(-2.414509559857E0,1.55E0,4.954680381983E0)); -#44346=CARTESIAN_POINT('',(-2.426131023729E0,1.55E0,4.951334384974E0)); -#44348=DIRECTION('',(0.E0,1.E0,0.E0)); -#44349=VECTOR('',#44348,1.E0); -#44350=SURFACE_OF_LINEAR_EXTRUSION('',#44347,#44349); -#44351=ORIENTED_EDGE('',*,*,#26312,.F.); -#44353=ORIENTED_EDGE('',*,*,#44352,.T.); -#44354=ORIENTED_EDGE('',*,*,#43494,.T.); -#44355=ORIENTED_EDGE('',*,*,#44295,.F.); -#44356=EDGE_LOOP('',(#44351,#44353,#44354,#44355)); -#44357=FACE_OUTER_BOUND('',#44356,.F.); -#44359=CARTESIAN_POINT('',(-3.157179944129E0,1.55E0,3.519017541968E0)); -#44360=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44361=DIRECTION('',(0.E0,0.E0,1.E0)); -#44362=AXIS2_PLACEMENT_3D('',#44359,#44360,#44361); -#44363=PLANE('',#44362); -#44364=ORIENTED_EDGE('',*,*,#26310,.F.); -#44366=ORIENTED_EDGE('',*,*,#44365,.T.); -#44367=ORIENTED_EDGE('',*,*,#43496,.T.); -#44368=ORIENTED_EDGE('',*,*,#44352,.F.); -#44369=EDGE_LOOP('',(#44364,#44366,#44367,#44368)); -#44370=FACE_OUTER_BOUND('',#44369,.F.); -#44372=CARTESIAN_POINT('',(-1.861541976619E0,1.55E0,3.987767659947E0)); -#44373=CARTESIAN_POINT('',(-1.882202575958E0,1.55E0,3.980292841657E0)); -#44374=CARTESIAN_POINT('',(-2.108472536879E0,1.55E0,3.898430412848E0)); -#44375=CARTESIAN_POINT('',(-2.540351859382E0,1.55E0,3.742180373522E0)); -#44376=CARTESIAN_POINT('',(-2.972231181885E0,1.55E0,3.585930334196E0)); -#44377=CARTESIAN_POINT('',(-3.198501142805E0,1.55E0,3.504067905387E0)); -#44378=CARTESIAN_POINT('',(-3.219161742144E0,1.55E0,3.496593087097E0)); -#44380=DIRECTION('',(0.E0,1.E0,0.E0)); -#44381=VECTOR('',#44380,1.E0); -#44382=SURFACE_OF_LINEAR_EXTRUSION('',#44379,#44381); -#44383=ORIENTED_EDGE('',*,*,#26308,.T.); -#44385=ORIENTED_EDGE('',*,*,#44384,.T.); -#44386=ORIENTED_EDGE('',*,*,#43498,.T.); -#44387=ORIENTED_EDGE('',*,*,#44365,.F.); -#44388=EDGE_LOOP('',(#44383,#44385,#44386,#44387)); -#44389=FACE_OUTER_BOUND('',#44388,.F.); -#44391=CARTESIAN_POINT('',(-1.923523774635E0,1.55E0,3.353966319546E0)); -#44392=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44393=DIRECTION('',(0.E0,0.E0,1.E0)); -#44394=AXIS2_PLACEMENT_3D('',#44391,#44392,#44393); -#44395=PLANE('',#44394); -#44396=ORIENTED_EDGE('',*,*,#26306,.F.); -#44398=ORIENTED_EDGE('',*,*,#44397,.T.); -#44399=ORIENTED_EDGE('',*,*,#43500,.T.); -#44400=ORIENTED_EDGE('',*,*,#44384,.F.); -#44401=EDGE_LOOP('',(#44396,#44398,#44399,#44400)); -#44402=FACE_OUTER_BOUND('',#44401,.F.); -#44404=CARTESIAN_POINT('',(-3.218731968891E0,1.55E0,2.883927638592E0)); -#44405=CARTESIAN_POINT('',(-3.198078746187E0,1.55E0,2.891422814735E0)); -#44406=CARTESIAN_POINT('',(-2.971884102458E0,1.55E0,2.973510182965E0)); -#44407=CARTESIAN_POINT('',(-2.540148037706E0,1.55E0,3.130189743283E0)); -#44408=CARTESIAN_POINT('',(-2.108411972954E0,1.55E0,3.286869303601E0)); -#44409=CARTESIAN_POINT('',(-1.882217329225E0,1.55E0,3.368956671831E0)); -#44410=CARTESIAN_POINT('',(-1.861564106521E0,1.55E0,3.376451847974E0)); -#44412=DIRECTION('',(0.E0,1.E0,0.E0)); -#44413=VECTOR('',#44412,1.E0); -#44414=SURFACE_OF_LINEAR_EXTRUSION('',#44411,#44413); -#44415=ORIENTED_EDGE('',*,*,#26304,.T.); -#44417=ORIENTED_EDGE('',*,*,#44416,.T.); -#44418=ORIENTED_EDGE('',*,*,#43502,.T.); -#44419=ORIENTED_EDGE('',*,*,#44397,.F.); -#44420=EDGE_LOOP('',(#44415,#44417,#44418,#44419)); -#44421=FACE_OUTER_BOUND('',#44420,.F.); -#44423=CARTESIAN_POINT('',(-3.156772300777E0,1.55E0,2.550046587517E0)); -#44424=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44425=DIRECTION('',(0.E0,0.E0,1.E0)); -#44426=AXIS2_PLACEMENT_3D('',#44423,#44424,#44425); -#44427=PLANE('',#44426); -#44428=ORIENTED_EDGE('',*,*,#26302,.F.); -#44430=ORIENTED_EDGE('',*,*,#44429,.T.); -#44431=ORIENTED_EDGE('',*,*,#43504,.T.); -#44432=ORIENTED_EDGE('',*,*,#44416,.F.); -#44433=EDGE_LOOP('',(#44428,#44430,#44431,#44432)); -#44434=FACE_OUTER_BOUND('',#44433,.F.); -#44436=CARTESIAN_POINT('',(-3.606375318241E0,1.55E0,2.386883004845E0)); -#44437=CARTESIAN_POINT('',(-3.585722095536E0,1.55E0,2.394378180988E0)); -#44438=CARTESIAN_POINT('',(-3.500461647940E0,1.55E0,2.425319699505E0)); -#44439=CARTESIAN_POINT('',(-3.350593975452E0,1.55E0,2.479707560396E0)); -#44440=CARTESIAN_POINT('',(-3.200726302964E0,1.55E0,2.534095421286E0)); -#44441=CARTESIAN_POINT('',(-3.115465855368E0,1.55E0,2.565036939803E0)); -#44442=CARTESIAN_POINT('',(-3.094812632663E0,1.55E0,2.572532115946E0)); -#44444=DIRECTION('',(0.E0,1.E0,0.E0)); -#44445=VECTOR('',#44444,1.E0); -#44446=SURFACE_OF_LINEAR_EXTRUSION('',#44443,#44445); -#44447=ORIENTED_EDGE('',*,*,#26300,.T.); -#44449=ORIENTED_EDGE('',*,*,#44448,.T.); -#44450=ORIENTED_EDGE('',*,*,#43506,.T.); -#44451=ORIENTED_EDGE('',*,*,#44429,.F.); -#44452=EDGE_LOOP('',(#44447,#44449,#44450,#44451)); -#44453=FACE_OUTER_BOUND('',#44452,.F.); -#44455=CARTESIAN_POINT('',(-3.544415650127E0,1.55E0,3.738820191946E0)); -#44456=DIRECTION('',(1.E0,0.E0,0.E0)); -#44457=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44458=AXIS2_PLACEMENT_3D('',#44455,#44456,#44457); -#44459=PLANE('',#44458); -#44460=ORIENTED_EDGE('',*,*,#26298,.F.); -#44462=ORIENTED_EDGE('',*,*,#44461,.T.); -#44463=ORIENTED_EDGE('',*,*,#43508,.T.); -#44464=ORIENTED_EDGE('',*,*,#44448,.F.); -#44465=EDGE_LOOP('',(#44460,#44462,#44463,#44464)); -#44466=FACE_OUTER_BOUND('',#44465,.F.); -#44468=CARTESIAN_POINT('',(-3.512369106765E0,1.55E0,4.049439446477E-1)); -#44469=CARTESIAN_POINT('',(-3.523158709695E0,1.55E0,4.122119889022E-1)); -#44470=CARTESIAN_POINT('',(-3.659818797392E0,1.55E0,5.057275169314E-1)); -#44471=CARTESIAN_POINT('',(-3.899289232098E0,1.55E0,7.055000952881E-1)); -#44472=CARTESIAN_POINT('',(-4.161825236093E0,1.55E0,1.061164382636E0)); -#44473=CARTESIAN_POINT('',(-4.339964395968E0,1.55E0,1.453086385463E0)); -#44474=CARTESIAN_POINT('',(-4.429747574789E0,1.55E0,1.872154618193E0)); -#44475=CARTESIAN_POINT('',(-4.429103562739E0,1.55E0,2.299374203780E0)); -#44476=CARTESIAN_POINT('',(-4.338255535641E0,1.55E0,2.717599764232E0)); -#44477=CARTESIAN_POINT('',(-4.159649836747E0,1.55E0,3.108029094254E0)); -#44478=CARTESIAN_POINT('',(-3.897535141638E0,1.55E0,3.461802933253E0)); -#44479=CARTESIAN_POINT('',(-3.659043827867E0,1.55E0,3.660577797039E0)); -#44480=CARTESIAN_POINT('',(-3.522994492077E0,1.55E0,3.753583359029E0)); -#44481=CARTESIAN_POINT('',(-3.512211639844E0,1.55E0,3.760839123805E0)); -#44483=DIRECTION('',(0.E0,1.E0,0.E0)); -#44484=VECTOR('',#44483,1.E0); -#44485=SURFACE_OF_LINEAR_EXTRUSION('',#44482,#44484); -#44486=ORIENTED_EDGE('',*,*,#26296,.F.); -#44488=ORIENTED_EDGE('',*,*,#44487,.T.); -#44489=ORIENTED_EDGE('',*,*,#43510,.T.); -#44490=ORIENTED_EDGE('',*,*,#44461,.F.); -#44491=EDGE_LOOP('',(#44486,#44488,#44489,#44490)); -#44492=FACE_OUTER_BOUND('',#44491,.F.); -#44494=CARTESIAN_POINT('',(-3.544593994093E0,1.55E0,9.180817657764E-1)); -#44495=DIRECTION('',(1.E0,0.E0,0.E0)); -#44496=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44497=AXIS2_PLACEMENT_3D('',#44494,#44495,#44496); -#44498=PLANE('',#44497); -#44499=ORIENTED_EDGE('',*,*,#26294,.F.); -#44501=ORIENTED_EDGE('',*,*,#44500,.T.); -#44502=ORIENTED_EDGE('',*,*,#43512,.T.); -#44503=ORIENTED_EDGE('',*,*,#44487,.F.); -#44504=EDGE_LOOP('',(#44499,#44501,#44502,#44503)); -#44505=FACE_OUTER_BOUND('',#44504,.F.); -#44507=CARTESIAN_POINT('',(-1.861631034924E0,1.55E0,1.530190934156E0)); -#44508=CARTESIAN_POINT('',(-1.882278933300E0,1.55E0,1.522681102858E0)); -#44509=CARTESIAN_POINT('',(-2.173096709017E0,1.55E0,1.416907992479E0)); -#44510=CARTESIAN_POINT('',(-2.734084362073E0,1.55E0,1.212871603019E0)); -#44511=CARTESIAN_POINT('',(-3.295072015130E0,1.55E0,1.008835213559E0)); -#44512=CARTESIAN_POINT('',(-3.585889790846E0,1.55E0,9.030621031804E-1)); -#44513=CARTESIAN_POINT('',(-3.606537689223E0,1.55E0,8.955522718824E-1)); -#44515=DIRECTION('',(0.E0,1.E0,0.E0)); -#44516=VECTOR('',#44515,1.E0); -#44517=SURFACE_OF_LINEAR_EXTRUSION('',#44514,#44516); -#44518=ORIENTED_EDGE('',*,*,#26292,.T.); -#44520=ORIENTED_EDGE('',*,*,#44519,.T.); -#44521=ORIENTED_EDGE('',*,*,#43514,.T.); -#44522=ORIENTED_EDGE('',*,*,#44500,.F.); -#44523=EDGE_LOOP('',(#44518,#44520,#44521,#44522)); -#44524=FACE_OUTER_BOUND('',#44523,.F.); -#44526=CARTESIAN_POINT('',(-1.923574730054E0,1.55E0,1.517666047689E-1)); -#44527=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44528=DIRECTION('',(0.E0,0.E0,1.E0)); -#44529=AXIS2_PLACEMENT_3D('',#44526,#44527,#44528); -#44530=PLANE('',#44529); -#44531=ORIENTED_EDGE('',*,*,#26290,.F.); -#44532=ORIENTED_EDGE('',*,*,#44186,.T.); -#44533=ORIENTED_EDGE('',*,*,#43516,.T.); -#44534=ORIENTED_EDGE('',*,*,#44519,.F.); -#44535=EDGE_LOOP('',(#44531,#44532,#44533,#44534)); -#44536=FACE_OUTER_BOUND('',#44535,.F.); -#44538=CARTESIAN_POINT('',(-2.571396448352E0,1.55E0,1.452272899908E0)); -#44539=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44540=DIRECTION('',(0.E0,0.E0,1.E0)); -#44541=AXIS2_PLACEMENT_3D('',#44538,#44539,#44540); -#44542=PLANE('',#44541); -#44543=ORIENTED_EDGE('',*,*,#27030,.F.); -#44545=ORIENTED_EDGE('',*,*,#44544,.T.); -#44546=ORIENTED_EDGE('',*,*,#43528,.T.); -#44548=ORIENTED_EDGE('',*,*,#44547,.F.); -#44549=EDGE_LOOP('',(#44543,#44545,#44546,#44548)); -#44550=FACE_OUTER_BOUND('',#44549,.F.); -#44552=CARTESIAN_POINT('',(-2.979494735070E0,1.55E0,1.308365505829E0)); -#44553=CARTESIAN_POINT('',(-2.958774085822E0,1.55E0,1.315672212899E0)); -#44554=CARTESIAN_POINT('',(-2.880397380078E0,1.55E0,1.343310132114E0)); -#44555=CARTESIAN_POINT('',(-2.744364617838E0,1.55E0,1.391279263474E0)); -#44556=CARTESIAN_POINT('',(-2.608331855599E0,1.55E0,1.439248394834E0)); -#44557=CARTESIAN_POINT('',(-2.529955149855E0,1.55E0,1.466886314049E0)); -#44558=CARTESIAN_POINT('',(-2.509234500606E0,1.55E0,1.474193021119E0)); -#44560=DIRECTION('',(0.E0,1.E0,0.E0)); -#44561=VECTOR('',#44560,1.E0); -#44562=SURFACE_OF_LINEAR_EXTRUSION('',#44559,#44561); -#44563=ORIENTED_EDGE('',*,*,#27052,.T.); -#44565=ORIENTED_EDGE('',*,*,#44564,.T.); -#44566=ORIENTED_EDGE('',*,*,#43530,.T.); -#44567=ORIENTED_EDGE('',*,*,#44544,.F.); -#44568=EDGE_LOOP('',(#44563,#44565,#44566,#44567)); -#44569=FACE_OUTER_BOUND('',#44568,.F.); -#44571=CARTESIAN_POINT('',(-2.917332787324E0,1.55E0,1.918446335862E0)); -#44572=DIRECTION('',(1.E0,0.E0,0.E0)); -#44573=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44574=AXIS2_PLACEMENT_3D('',#44571,#44572,#44573); -#44575=PLANE('',#44574); -#44576=ORIENTED_EDGE('',*,*,#27050,.F.); -#44578=ORIENTED_EDGE('',*,*,#44577,.T.); -#44579=ORIENTED_EDGE('',*,*,#43532,.T.); -#44580=ORIENTED_EDGE('',*,*,#44564,.F.); -#44581=EDGE_LOOP('',(#44576,#44578,#44579,#44580)); -#44582=FACE_OUTER_BOUND('',#44581,.F.); -#44584=CARTESIAN_POINT('',(-3.218936522882E0,1.55E0,1.811536970660E0)); -#44585=CARTESIAN_POINT('',(-3.198227854369E0,1.55E0,1.818877564770E0)); -#44586=CARTESIAN_POINT('',(-3.137606230852E0,1.55E0,1.840366089359E0)); -#44587=CARTESIAN_POINT('',(-3.037071652333E0,1.55E0,1.876002544427E0)); -#44588=CARTESIAN_POINT('',(-2.936537073814E0,1.55E0,1.911638999494E0)); -#44589=CARTESIAN_POINT('',(-2.875915450297E0,1.55E0,1.933127524084E0)); -#44590=CARTESIAN_POINT('',(-2.855206781784E0,1.55E0,1.940468118194E0)); -#44592=DIRECTION('',(0.E0,1.E0,0.E0)); -#44593=VECTOR('',#44592,1.E0); -#44594=SURFACE_OF_LINEAR_EXTRUSION('',#44591,#44593); -#44595=ORIENTED_EDGE('',*,*,#27048,.T.); -#44597=ORIENTED_EDGE('',*,*,#44596,.T.); -#44598=ORIENTED_EDGE('',*,*,#43534,.T.); -#44599=ORIENTED_EDGE('',*,*,#44577,.F.); -#44600=EDGE_LOOP('',(#44595,#44597,#44598,#44599)); -#44601=FACE_OUTER_BOUND('',#44600,.F.); -#44603=CARTESIAN_POINT('',(-3.156810517342E0,1.55E0,1.187063609591E0)); -#44604=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44605=DIRECTION('',(0.E0,0.E0,1.E0)); -#44606=AXIS2_PLACEMENT_3D('',#44603,#44604,#44605); -#44607=PLANE('',#44606); -#44608=ORIENTED_EDGE('',*,*,#27046,.F.); -#44610=ORIENTED_EDGE('',*,*,#44609,.T.); -#44611=ORIENTED_EDGE('',*,*,#43536,.T.); -#44612=ORIENTED_EDGE('',*,*,#44596,.F.); -#44613=EDGE_LOOP('',(#44608,#44610,#44611,#44612)); -#44614=FACE_OUTER_BOUND('',#44613,.F.); -#44616=CARTESIAN_POINT('',(-3.605945789970E0,1.55E0,1.026466229548E0)); -#44617=CARTESIAN_POINT('',(-3.585257399389E0,1.55E0,1.033863781081E0)); -#44618=CARTESIAN_POINT('',(-3.500057325328E0,1.55E0,1.064328786855E0)); -#44619=CARTESIAN_POINT('',(-3.350345567785E0,1.55E0,1.117861246869E0)); -#44620=CARTESIAN_POINT('',(-3.200633810242E0,1.55E0,1.171393706883E0)); -#44621=CARTESIAN_POINT('',(-3.115433736180E0,1.55E0,1.201858712657E0)); -#44622=CARTESIAN_POINT('',(-3.094745345600E0,1.55E0,1.209256264190E0)); -#44624=DIRECTION('',(0.E0,1.E0,0.E0)); -#44625=VECTOR('',#44624,1.E0); -#44626=SURFACE_OF_LINEAR_EXTRUSION('',#44623,#44625); -#44627=ORIENTED_EDGE('',*,*,#27044,.T.); -#44629=ORIENTED_EDGE('',*,*,#44628,.T.); -#44630=ORIENTED_EDGE('',*,*,#43538,.T.); -#44631=ORIENTED_EDGE('',*,*,#44609,.F.); -#44632=EDGE_LOOP('',(#44627,#44629,#44630,#44631)); -#44633=FACE_OUTER_BOUND('',#44632,.F.); -#44635=CARTESIAN_POINT('',(-3.543880618228E0,1.55E0,2.304655147416E0)); -#44636=DIRECTION('',(1.E0,0.E0,0.E0)); -#44637=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44638=AXIS2_PLACEMENT_3D('',#44635,#44636,#44637); -#44639=PLANE('',#44638); -#44640=ORIENTED_EDGE('',*,*,#27042,.F.); -#44642=ORIENTED_EDGE('',*,*,#44641,.T.); -#44643=ORIENTED_EDGE('',*,*,#43540,.T.); -#44644=ORIENTED_EDGE('',*,*,#44628,.F.); -#44645=EDGE_LOOP('',(#44640,#44642,#44643,#44644)); -#44646=FACE_OUTER_BOUND('',#44645,.F.); -#44648=CARTESIAN_POINT('',(-1.861666017359E0,1.55E0,2.915140732343E0)); -#44649=CARTESIAN_POINT('',(-1.882319240063E0,1.55E0,2.907645556201E0)); -#44650=CARTESIAN_POINT('',(-2.173014951561E0,1.55E0,2.802150370641E0)); -#44651=CARTESIAN_POINT('',(-2.733753151850E0,1.55E0,2.598655175665E0)); -#44652=CARTESIAN_POINT('',(-3.294491352140E0,1.55E0,2.395159980690E0)); -#44653=CARTESIAN_POINT('',(-3.585187063637E0,1.55E0,2.289664795130E0)); -#44654=CARTESIAN_POINT('',(-3.605840286342E0,1.55E0,2.282169618988E0)); -#44656=DIRECTION('',(0.E0,1.E0,0.E0)); -#44657=VECTOR('',#44656,1.E0); -#44658=SURFACE_OF_LINEAR_EXTRUSION('',#44655,#44657); -#44659=ORIENTED_EDGE('',*,*,#27040,.T.); -#44661=ORIENTED_EDGE('',*,*,#44660,.T.); -#44662=ORIENTED_EDGE('',*,*,#43542,.T.); -#44663=ORIENTED_EDGE('',*,*,#44641,.F.); -#44664=EDGE_LOOP('',(#44659,#44661,#44662,#44663)); -#44665=FACE_OUTER_BOUND('',#44664,.F.); -#44667=CARTESIAN_POINT('',(-1.923625685473E0,1.55E0,1.636145592944E0)); -#44668=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44669=DIRECTION('',(0.E0,0.E0,1.E0)); -#44670=AXIS2_PLACEMENT_3D('',#44667,#44668,#44669); -#44671=PLANE('',#44670); -#44672=ORIENTED_EDGE('',*,*,#27038,.F.); -#44674=ORIENTED_EDGE('',*,*,#44673,.T.); -#44675=ORIENTED_EDGE('',*,*,#43544,.T.); -#44676=ORIENTED_EDGE('',*,*,#44660,.F.); -#44677=EDGE_LOOP('',(#44672,#44674,#44675,#44676)); -#44678=FACE_OUTER_BOUND('',#44677,.F.); -#44680=CARTESIAN_POINT('',(-2.372595352990E0,1.55E0,1.475607428351E0)); -#44681=CARTESIAN_POINT('',(-2.351906962409E0,1.55E0,1.483004979884E0)); -#44682=CARTESIAN_POINT('',(-2.266734489199E0,1.55E0,1.513460116416E0)); -#44683=CARTESIAN_POINT('',(-2.117077933360E0,1.55E0,1.566972837947E0)); -#44684=CARTESIAN_POINT('',(-1.967421377521E0,1.55E0,1.620485559478E0)); -#44685=CARTESIAN_POINT('',(-1.882248904311E0,1.55E0,1.650940696010E0)); -#44686=CARTESIAN_POINT('',(-1.861560513731E0,1.55E0,1.658338247543E0)); -#44688=DIRECTION('',(0.E0,1.E0,0.E0)); -#44689=VECTOR('',#44688,1.E0); -#44690=SURFACE_OF_LINEAR_EXTRUSION('',#44687,#44689); -#44691=ORIENTED_EDGE('',*,*,#27036,.T.); -#44693=ORIENTED_EDGE('',*,*,#44692,.T.); -#44694=ORIENTED_EDGE('',*,*,#43546,.T.); -#44695=ORIENTED_EDGE('',*,*,#44673,.F.); -#44696=EDGE_LOOP('',(#44691,#44693,#44694,#44695)); -#44697=FACE_OUTER_BOUND('',#44696,.F.); -#44699=CARTESIAN_POINT('',(-2.310530181248E0,1.55E0,2.139253857638E0)); -#44700=DIRECTION('',(1.E0,0.E0,0.E0)); -#44701=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44702=AXIS2_PLACEMENT_3D('',#44699,#44700,#44701); -#44703=PLANE('',#44702); -#44704=ORIENTED_EDGE('',*,*,#27034,.F.); -#44706=ORIENTED_EDGE('',*,*,#44705,.T.); -#44707=ORIENTED_EDGE('',*,*,#43548,.T.); -#44708=ORIENTED_EDGE('',*,*,#44692,.F.); -#44709=EDGE_LOOP('',(#44704,#44706,#44707,#44708)); -#44710=FACE_OUTER_BOUND('',#44709,.F.); -#44712=CARTESIAN_POINT('',(-2.633548393311E0,1.55E0,2.025182535481E0)); -#44713=CARTESIAN_POINT('',(-2.612831078325E0,1.55E0,2.032498691115E0)); -#44714=CARTESIAN_POINT('',(-2.548636052154E0,1.55E0,2.055168655958E0)); -#44715=CARTESIAN_POINT('',(-2.440963314800E0,1.55E0,2.093192430010E0)); -#44716=CARTESIAN_POINT('',(-2.333290577446E0,1.55E0,2.131216204062E0)); -#44717=CARTESIAN_POINT('',(-2.269095551275E0,1.55E0,2.153886168905E0)); -#44718=CARTESIAN_POINT('',(-2.248378236289E0,1.55E0,2.161202324539E0)); -#44720=DIRECTION('',(0.E0,1.E0,0.E0)); -#44721=VECTOR('',#44720,1.E0); -#44722=SURFACE_OF_LINEAR_EXTRUSION('',#44719,#44721); -#44723=ORIENTED_EDGE('',*,*,#27032,.T.); -#44724=ORIENTED_EDGE('',*,*,#44547,.T.); -#44725=ORIENTED_EDGE('',*,*,#43550,.T.); -#44726=ORIENTED_EDGE('',*,*,#44705,.F.); -#44727=EDGE_LOOP('',(#44723,#44724,#44725,#44726)); -#44728=FACE_OUTER_BOUND('',#44727,.F.); -#44730=CARTESIAN_POINT('',(6.E-1,3.E-1,-3.83E0)); -#44731=DIRECTION('',(1.E0,0.E0,0.E0)); -#44732=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44733=AXIS2_PLACEMENT_3D('',#44730,#44731,#44732); -#44734=PLANE('',#44733); -#44735=ORIENTED_EDGE('',*,*,#24560,.T.); -#44736=ORIENTED_EDGE('',*,*,#24453,.F.); -#44738=ORIENTED_EDGE('',*,*,#44737,.F.); -#44739=ORIENTED_EDGE('',*,*,#24298,.T.); -#44740=EDGE_LOOP('',(#44735,#44736,#44738,#44739)); -#44741=FACE_OUTER_BOUND('',#44740,.F.); -#44743=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.83E0)); -#44744=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44745=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44746=AXIS2_PLACEMENT_3D('',#44743,#44744,#44745); -#44747=PLANE('',#44746); -#44748=ORIENTED_EDGE('',*,*,#24300,.T.); -#44749=ORIENTED_EDGE('',*,*,#44737,.T.); -#44750=ORIENTED_EDGE('',*,*,#24451,.F.); -#44752=ORIENTED_EDGE('',*,*,#44751,.F.); -#44753=EDGE_LOOP('',(#44748,#44749,#44750,#44752)); -#44754=FACE_OUTER_BOUND('',#44753,.F.); -#44756=CARTESIAN_POINT('',(5.1E0,3.E-1,-3.98E0)); -#44757=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44758=DIRECTION('',(0.E0,0.E0,1.E0)); -#44759=AXIS2_PLACEMENT_3D('',#44756,#44757,#44758); -#44760=PLANE('',#44759); -#44761=ORIENTED_EDGE('',*,*,#24563,.F.); -#44762=ORIENTED_EDGE('',*,*,#24302,.T.); -#44763=ORIENTED_EDGE('',*,*,#44751,.T.); -#44764=ORIENTED_EDGE('',*,*,#24449,.F.); -#44765=EDGE_LOOP('',(#44761,#44762,#44763,#44764)); -#44766=FACE_OUTER_BOUND('',#44765,.F.); -#44768=CARTESIAN_POINT('',(-5.25E0,3.E-1,6.861069017863E0)); -#44769=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44770=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44771=AXIS2_PLACEMENT_3D('',#44768,#44769,#44770); -#44772=PLANE('',#44771); -#44773=ORIENTED_EDGE('',*,*,#24487,.T.); -#44774=ORIENTED_EDGE('',*,*,#24410,.F.); -#44776=ORIENTED_EDGE('',*,*,#44775,.F.); -#44777=ORIENTED_EDGE('',*,*,#24322,.T.); -#44778=EDGE_LOOP('',(#44773,#44774,#44776,#44777)); -#44779=FACE_OUTER_BOUND('',#44778,.F.); -#44781=CARTESIAN_POINT('',(-5.25E0,3.E-1,8.628565170500E-1)); -#44782=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44783=DIRECTION('',(0.E0,0.E0,1.E0)); -#44784=AXIS2_PLACEMENT_3D('',#44781,#44782,#44783); -#44785=PLANE('',#44784); -#44786=ORIENTED_EDGE('',*,*,#24324,.T.); -#44787=ORIENTED_EDGE('',*,*,#44775,.T.); -#44788=ORIENTED_EDGE('',*,*,#24408,.F.); -#44790=ORIENTED_EDGE('',*,*,#44789,.F.); -#44791=EDGE_LOOP('',(#44786,#44787,#44788,#44790)); -#44792=FACE_OUTER_BOUND('',#44791,.F.); -#44794=CARTESIAN_POINT('',(-5.4E0,3.E-1,8.628565170500E-1)); -#44795=DIRECTION('',(0.E0,0.E0,1.E0)); -#44796=DIRECTION('',(1.E0,0.E0,0.E0)); -#44797=AXIS2_PLACEMENT_3D('',#44794,#44795,#44796); -#44798=PLANE('',#44797); -#44799=ORIENTED_EDGE('',*,*,#24490,.F.); -#44800=ORIENTED_EDGE('',*,*,#24326,.T.); -#44801=ORIENTED_EDGE('',*,*,#44789,.T.); -#44802=ORIENTED_EDGE('',*,*,#24406,.F.); -#44803=EDGE_LOOP('',(#44799,#44800,#44801,#44802)); -#44804=FACE_OUTER_BOUND('',#44803,.F.); -#44806=CARTESIAN_POINT('',(6.8E0,3.E-1,5.639068448582E0)); -#44807=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44808=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44809=AXIS2_PLACEMENT_3D('',#44806,#44807,#44808); -#44810=PLANE('',#44809); -#44811=ORIENTED_EDGE('',*,*,#24394,.F.); -#44812=ORIENTED_EDGE('',*,*,#24282,.T.); -#44814=ORIENTED_EDGE('',*,*,#44813,.T.); -#44815=ORIENTED_EDGE('',*,*,#24433,.F.); -#44816=EDGE_LOOP('',(#44811,#44812,#44814,#44815)); -#44817=FACE_OUTER_BOUND('',#44816,.F.); -#44819=CARTESIAN_POINT('',(6.65E0,3.E-1,5.639068448582E0)); -#44820=DIRECTION('',(1.E0,0.E0,0.E0)); -#44821=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44822=AXIS2_PLACEMENT_3D('',#44819,#44820,#44821); -#44823=PLANE('',#44822); -#44824=ORIENTED_EDGE('',*,*,#24280,.T.); -#44826=ORIENTED_EDGE('',*,*,#44825,.T.); -#44827=ORIENTED_EDGE('',*,*,#24435,.F.); -#44828=ORIENTED_EDGE('',*,*,#44813,.F.); -#44829=EDGE_LOOP('',(#44824,#44826,#44827,#44828)); -#44830=FACE_OUTER_BOUND('',#44829,.F.); -#44832=CARTESIAN_POINT('',(6.65E0,3.E-1,9.156381348264E-1)); -#44833=DIRECTION('',(0.E0,0.E0,1.E0)); -#44834=DIRECTION('',(1.E0,0.E0,0.E0)); -#44835=AXIS2_PLACEMENT_3D('',#44832,#44833,#44834); -#44836=PLANE('',#44835); -#44837=ORIENTED_EDGE('',*,*,#24391,.T.); -#44838=ORIENTED_EDGE('',*,*,#24437,.F.); -#44839=ORIENTED_EDGE('',*,*,#44825,.F.); -#44840=ORIENTED_EDGE('',*,*,#24278,.T.); -#44841=EDGE_LOOP('',(#44837,#44838,#44839,#44840)); -#44842=FACE_OUTER_BOUND('',#44841,.F.); -#44844=CARTESIAN_POINT('',(6.8E0,3.E-1,-8.436186517363E-2)); -#44845=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44846=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44847=AXIS2_PLACEMENT_3D('',#44844,#44845,#44846); -#44848=PLANE('',#44847); -#44849=ORIENTED_EDGE('',*,*,#24387,.F.); -#44850=ORIENTED_EDGE('',*,*,#24292,.T.); -#44852=ORIENTED_EDGE('',*,*,#44851,.T.); -#44853=ORIENTED_EDGE('',*,*,#24440,.F.); -#44854=EDGE_LOOP('',(#44849,#44850,#44852,#44853)); -#44855=FACE_OUTER_BOUND('',#44854,.F.); -#44857=CARTESIAN_POINT('',(6.65E0,3.E-1,-8.436186517363E-2)); -#44858=DIRECTION('',(1.E0,0.E0,0.E0)); -#44859=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44860=AXIS2_PLACEMENT_3D('',#44857,#44858,#44859); -#44861=PLANE('',#44860); -#44862=ORIENTED_EDGE('',*,*,#24290,.T.); -#44864=ORIENTED_EDGE('',*,*,#44863,.T.); -#44865=ORIENTED_EDGE('',*,*,#24442,.F.); -#44866=ORIENTED_EDGE('',*,*,#44851,.F.); -#44867=EDGE_LOOP('',(#44862,#44864,#44865,#44866)); -#44868=FACE_OUTER_BOUND('',#44867,.F.); -#44870=CARTESIAN_POINT('',(6.65E0,3.E-1,-1.58E0)); -#44871=DIRECTION('',(0.E0,0.E0,1.E0)); -#44872=DIRECTION('',(1.E0,0.E0,0.E0)); -#44873=AXIS2_PLACEMENT_3D('',#44870,#44871,#44872); -#44874=PLANE('',#44873); -#44875=ORIENTED_EDGE('',*,*,#24384,.T.); -#44876=ORIENTED_EDGE('',*,*,#24444,.F.); -#44877=ORIENTED_EDGE('',*,*,#44863,.F.); -#44878=ORIENTED_EDGE('',*,*,#24288,.T.); -#44879=EDGE_LOOP('',(#44875,#44876,#44877,#44878)); -#44880=FACE_OUTER_BOUND('',#44879,.F.); -#44882=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.3735E1)); -#44883=DIRECTION('',(0.E0,1.E0,0.E0)); -#44884=DIRECTION('',(1.E0,0.E0,0.E0)); -#44885=AXIS2_PLACEMENT_3D('',#44882,#44883,#44884); -#44886=CYLINDRICAL_SURFACE('',#44885,2.5E-1); -#44887=ORIENTED_EDGE('',*,*,#24052,.T.); -#44888=ORIENTED_EDGE('',*,*,#23986,.T.); -#44889=ORIENTED_EDGE('',*,*,#24127,.T.); -#44890=ORIENTED_EDGE('',*,*,#23964,.F.); -#44891=EDGE_LOOP('',(#44887,#44888,#44889,#44890)); -#44892=FACE_OUTER_BOUND('',#44891,.F.); -#44894=FILL_AREA_STYLE_COLOUR('',#15); -#44895=FILL_AREA_STYLE('',(#44894)); -#44896=SURFACE_STYLE_FILL_AREA(#44895); -#44897=SURFACE_SIDE_STYLE('',(#44896)); -#44898=SURFACE_STYLE_USAGE(.NEGATIVE.,#44897); -#44899=PRESENTATION_STYLE_ASSIGNMENT((#44898)); -#44900=STYLED_ITEM('',(#44899),#44893); -#44901=CARTESIAN_POINT('',(7.5E0,-3.E-1,-1.43E1)); -#44902=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44903=DIRECTION('',(-1.E0,0.E0,0.E0)); -#44904=AXIS2_PLACEMENT_3D('',#44901,#44902,#44903); -#44905=PLANE('',#44904); -#44906=ORIENTED_EDGE('',*,*,#22299,.F.); -#44908=ORIENTED_EDGE('',*,*,#44907,.T.); -#44909=ORIENTED_EDGE('',*,*,#24130,.T.); -#44910=ORIENTED_EDGE('',*,*,#23982,.F.); -#44911=EDGE_LOOP('',(#44906,#44908,#44909,#44910)); -#44912=FACE_OUTER_BOUND('',#44911,.F.); -#44914=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#44915=DIRECTION('',(1.E0,0.E0,0.E0)); -#44916=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44917=AXIS2_PLACEMENT_3D('',#44914,#44915,#44916); -#44918=PLANE('',#44917); -#44920=ORIENTED_EDGE('',*,*,#44919,.T.); -#44921=ORIENTED_EDGE('',*,*,#24132,.T.); -#44922=ORIENTED_EDGE('',*,*,#44907,.F.); -#44923=ORIENTED_EDGE('',*,*,#22297,.F.); -#44925=ORIENTED_EDGE('',*,*,#44924,.T.); -#44927=ORIENTED_EDGE('',*,*,#44926,.T.); -#44928=EDGE_LOOP('',(#44920,#44921,#44922,#44923,#44925,#44927)); -#44929=FACE_OUTER_BOUND('',#44928,.F.); -#44931=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#44932=DIRECTION('',(1.E0,0.E0,0.E0)); -#44933=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44934=AXIS2_PLACEMENT_3D('',#44931,#44932,#44933); -#44935=PLANE('',#44934); -#44937=ORIENTED_EDGE('',*,*,#44936,.T.); -#44938=ORIENTED_EDGE('',*,*,#24140,.T.); -#44940=ORIENTED_EDGE('',*,*,#44939,.F.); -#44942=ORIENTED_EDGE('',*,*,#44941,.F.); -#44944=ORIENTED_EDGE('',*,*,#44943,.F.); -#44945=ORIENTED_EDGE('',*,*,#22289,.F.); -#44947=ORIENTED_EDGE('',*,*,#44946,.T.); -#44949=ORIENTED_EDGE('',*,*,#44948,.T.); -#44950=EDGE_LOOP('',(#44937,#44938,#44940,#44942,#44944,#44945,#44947,#44949)); -#44951=FACE_OUTER_BOUND('',#44950,.F.); -#44953=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#44954=DIRECTION('',(1.E0,0.E0,0.E0)); -#44955=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44956=AXIS2_PLACEMENT_3D('',#44953,#44954,#44955); -#44957=PLANE('',#44956); -#44959=ORIENTED_EDGE('',*,*,#44958,.T.); -#44960=ORIENTED_EDGE('',*,*,#24148,.T.); -#44962=ORIENTED_EDGE('',*,*,#44961,.F.); -#44964=ORIENTED_EDGE('',*,*,#44963,.F.); -#44966=ORIENTED_EDGE('',*,*,#44965,.F.); -#44967=ORIENTED_EDGE('',*,*,#22281,.F.); -#44969=ORIENTED_EDGE('',*,*,#44968,.T.); -#44971=ORIENTED_EDGE('',*,*,#44970,.T.); -#44972=EDGE_LOOP('',(#44959,#44960,#44962,#44964,#44966,#44967,#44969,#44971)); -#44973=FACE_OUTER_BOUND('',#44972,.F.); -#44975=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#44976=DIRECTION('',(1.E0,0.E0,0.E0)); -#44977=DIRECTION('',(0.E0,0.E0,-1.E0)); -#44978=AXIS2_PLACEMENT_3D('',#44975,#44976,#44977); -#44979=PLANE('',#44978); -#44981=ORIENTED_EDGE('',*,*,#44980,.T.); -#44982=ORIENTED_EDGE('',*,*,#24156,.T.); -#44984=ORIENTED_EDGE('',*,*,#44983,.F.); -#44986=ORIENTED_EDGE('',*,*,#44985,.F.); -#44988=ORIENTED_EDGE('',*,*,#44987,.F.); -#44989=ORIENTED_EDGE('',*,*,#22273,.F.); -#44991=ORIENTED_EDGE('',*,*,#44990,.T.); -#44993=ORIENTED_EDGE('',*,*,#44992,.T.); -#44994=EDGE_LOOP('',(#44981,#44982,#44984,#44986,#44988,#44989,#44991,#44993)); -#44995=FACE_OUTER_BOUND('',#44994,.F.); -#44997=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#44998=DIRECTION('',(1.E0,0.E0,0.E0)); -#44999=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45000=AXIS2_PLACEMENT_3D('',#44997,#44998,#44999); -#45001=PLANE('',#45000); -#45003=ORIENTED_EDGE('',*,*,#45002,.T.); -#45004=ORIENTED_EDGE('',*,*,#24164,.T.); -#45006=ORIENTED_EDGE('',*,*,#45005,.F.); -#45008=ORIENTED_EDGE('',*,*,#45007,.F.); -#45010=ORIENTED_EDGE('',*,*,#45009,.F.); -#45011=ORIENTED_EDGE('',*,*,#22265,.F.); -#45013=ORIENTED_EDGE('',*,*,#45012,.T.); -#45015=ORIENTED_EDGE('',*,*,#45014,.T.); -#45016=EDGE_LOOP('',(#45003,#45004,#45006,#45008,#45010,#45011,#45013,#45015)); -#45017=FACE_OUTER_BOUND('',#45016,.F.); -#45019=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#45020=DIRECTION('',(1.E0,0.E0,0.E0)); -#45021=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45022=AXIS2_PLACEMENT_3D('',#45019,#45020,#45021); -#45023=PLANE('',#45022); -#45025=ORIENTED_EDGE('',*,*,#45024,.T.); -#45026=ORIENTED_EDGE('',*,*,#24172,.T.); -#45028=ORIENTED_EDGE('',*,*,#45027,.F.); -#45030=ORIENTED_EDGE('',*,*,#45029,.F.); -#45032=ORIENTED_EDGE('',*,*,#45031,.F.); -#45033=ORIENTED_EDGE('',*,*,#22257,.F.); -#45035=ORIENTED_EDGE('',*,*,#45034,.T.); -#45037=ORIENTED_EDGE('',*,*,#45036,.T.); -#45038=EDGE_LOOP('',(#45025,#45026,#45028,#45030,#45032,#45033,#45035,#45037)); -#45039=FACE_OUTER_BOUND('',#45038,.F.); -#45041=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#45042=DIRECTION('',(1.E0,0.E0,0.E0)); -#45043=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45044=AXIS2_PLACEMENT_3D('',#45041,#45042,#45043); -#45045=PLANE('',#45044); -#45047=ORIENTED_EDGE('',*,*,#45046,.T.); -#45048=ORIENTED_EDGE('',*,*,#24180,.T.); -#45050=ORIENTED_EDGE('',*,*,#45049,.F.); -#45052=ORIENTED_EDGE('',*,*,#45051,.F.); -#45054=ORIENTED_EDGE('',*,*,#45053,.F.); -#45055=ORIENTED_EDGE('',*,*,#22249,.F.); -#45057=ORIENTED_EDGE('',*,*,#45056,.T.); -#45059=ORIENTED_EDGE('',*,*,#45058,.T.); -#45060=EDGE_LOOP('',(#45047,#45048,#45050,#45052,#45054,#45055,#45057,#45059)); -#45061=FACE_OUTER_BOUND('',#45060,.F.); -#45063=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#45064=DIRECTION('',(1.E0,0.E0,0.E0)); -#45065=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45066=AXIS2_PLACEMENT_3D('',#45063,#45064,#45065); -#45067=PLANE('',#45066); -#45069=ORIENTED_EDGE('',*,*,#45068,.T.); -#45070=ORIENTED_EDGE('',*,*,#24188,.T.); -#45072=ORIENTED_EDGE('',*,*,#45071,.F.); -#45074=ORIENTED_EDGE('',*,*,#45073,.F.); -#45076=ORIENTED_EDGE('',*,*,#45075,.F.); -#45077=ORIENTED_EDGE('',*,*,#22241,.F.); -#45079=ORIENTED_EDGE('',*,*,#45078,.T.); -#45081=ORIENTED_EDGE('',*,*,#45080,.T.); -#45082=EDGE_LOOP('',(#45069,#45070,#45072,#45074,#45076,#45077,#45079,#45081)); -#45083=FACE_OUTER_BOUND('',#45082,.F.); -#45085=CARTESIAN_POINT('',(7.5E0,-3.E-1,1.37E1)); -#45086=DIRECTION('',(1.E0,0.E0,0.E0)); -#45087=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45088=AXIS2_PLACEMENT_3D('',#45085,#45086,#45087); -#45089=PLANE('',#45088); -#45091=ORIENTED_EDGE('',*,*,#45090,.F.); -#45092=ORIENTED_EDGE('',*,*,#22233,.F.); -#45094=ORIENTED_EDGE('',*,*,#45093,.T.); -#45095=ORIENTED_EDGE('',*,*,#24196,.T.); -#45097=ORIENTED_EDGE('',*,*,#45096,.F.); -#45099=ORIENTED_EDGE('',*,*,#45098,.F.); -#45100=EDGE_LOOP('',(#45091,#45092,#45094,#45095,#45097,#45099)); -#45101=FACE_OUTER_BOUND('',#45100,.F.); -#45103=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,4.55E0)); -#45104=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45105=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45106=AXIS2_PLACEMENT_3D('',#45103,#45104,#45105); -#45107=PLANE('',#45106); -#45109=ORIENTED_EDGE('',*,*,#45108,.F.); -#45110=ORIENTED_EDGE('',*,*,#44924,.F.); -#45111=ORIENTED_EDGE('',*,*,#22295,.T.); -#45113=ORIENTED_EDGE('',*,*,#45112,.F.); -#45114=EDGE_LOOP('',(#45109,#45110,#45111,#45113)); -#45115=FACE_OUTER_BOUND('',#45114,.F.); -#45117=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,4.55E0)); -#45118=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45119=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45120=AXIS2_PLACEMENT_3D('',#45117,#45118,#45119); -#45121=PLANE('',#45120); -#45123=ORIENTED_EDGE('',*,*,#45122,.T.); -#45125=ORIENTED_EDGE('',*,*,#45124,.F.); -#45126=ORIENTED_EDGE('',*,*,#24134,.F.); -#45127=ORIENTED_EDGE('',*,*,#44919,.F.); -#45128=EDGE_LOOP('',(#45123,#45125,#45126,#45127)); -#45129=FACE_OUTER_BOUND('',#45128,.F.); -#45131=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#45132=DIRECTION('',(0.E0,1.E0,0.E0)); -#45133=DIRECTION('',(1.E0,0.E0,0.E0)); -#45134=AXIS2_PLACEMENT_3D('',#45131,#45132,#45133); -#45135=PLANE('',#45134); -#45137=ORIENTED_EDGE('',*,*,#45136,.T.); -#45139=ORIENTED_EDGE('',*,*,#45138,.T.); -#45141=ORIENTED_EDGE('',*,*,#45140,.T.); -#45143=ORIENTED_EDGE('',*,*,#45142,.T.); -#45144=EDGE_LOOP('',(#45137,#45139,#45141,#45143)); -#45145=FACE_OUTER_BOUND('',#45144,.F.); -#45147=FILL_AREA_STYLE_COLOUR('',#15); -#45148=FILL_AREA_STYLE('',(#45147)); -#45149=SURFACE_STYLE_FILL_AREA(#45148); -#45150=SURFACE_SIDE_STYLE('',(#45149)); -#45151=SURFACE_STYLE_USAGE(.NEGATIVE.,#45150); -#45152=PRESENTATION_STYLE_ASSIGNMENT((#45151)); -#45153=STYLED_ITEM('',(#45152),#45146); -#45154=CARTESIAN_POINT('',(0.E0,-2.5E-1,0.E0)); -#45155=DIRECTION('',(0.E0,1.E0,0.E0)); -#45156=DIRECTION('',(1.E0,0.E0,0.E0)); -#45157=AXIS2_PLACEMENT_3D('',#45154,#45155,#45156); -#45158=PLANE('',#45157); -#45159=ORIENTED_EDGE('',*,*,#45108,.T.); -#45161=ORIENTED_EDGE('',*,*,#45160,.T.); -#45163=ORIENTED_EDGE('',*,*,#45162,.T.); -#45165=ORIENTED_EDGE('',*,*,#45164,.T.); -#45166=EDGE_LOOP('',(#45159,#45161,#45163,#45165)); -#45167=FACE_OUTER_BOUND('',#45166,.F.); -#45169=FILL_AREA_STYLE_COLOUR('',#15); -#45170=FILL_AREA_STYLE('',(#45169)); -#45171=SURFACE_STYLE_FILL_AREA(#45170); -#45172=SURFACE_SIDE_STYLE('',(#45171)); -#45173=SURFACE_STYLE_USAGE(.NEGATIVE.,#45172); -#45174=PRESENTATION_STYLE_ASSIGNMENT((#45173)); -#45175=STYLED_ITEM('',(#45174),#45168); -#45176=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,5.25E0)); -#45177=DIRECTION('',(0.E0,0.E0,1.E0)); -#45178=DIRECTION('',(1.E0,0.E0,0.E0)); -#45179=AXIS2_PLACEMENT_3D('',#45176,#45177,#45178); -#45180=PLANE('',#45179); -#45181=ORIENTED_EDGE('',*,*,#45136,.F.); -#45183=ORIENTED_EDGE('',*,*,#45182,.F.); -#45184=ORIENTED_EDGE('',*,*,#22171,.T.); -#45186=ORIENTED_EDGE('',*,*,#45185,.F.); -#45187=EDGE_LOOP('',(#45181,#45183,#45184,#45186)); -#45188=FACE_OUTER_BOUND('',#45187,.F.); -#45190=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,5.25E0)); -#45191=DIRECTION('',(0.E0,0.E0,1.E0)); -#45192=DIRECTION('',(1.E0,0.E0,0.E0)); -#45193=AXIS2_PLACEMENT_3D('',#45190,#45191,#45192); -#45194=PLANE('',#45193); -#45196=ORIENTED_EDGE('',*,*,#45195,.T.); -#45198=ORIENTED_EDGE('',*,*,#45197,.F.); -#45199=ORIENTED_EDGE('',*,*,#24258,.F.); -#45201=ORIENTED_EDGE('',*,*,#45200,.F.); -#45202=EDGE_LOOP('',(#45196,#45198,#45199,#45201)); -#45203=FACE_OUTER_BOUND('',#45202,.F.); -#45205=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45206=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45207=DIRECTION('',(0.E0,0.E0,1.E0)); -#45208=AXIS2_PLACEMENT_3D('',#45205,#45206,#45207); -#45209=PLANE('',#45208); -#45211=ORIENTED_EDGE('',*,*,#45210,.F.); -#45212=ORIENTED_EDGE('',*,*,#22165,.F.); -#45214=ORIENTED_EDGE('',*,*,#45213,.T.); -#45215=ORIENTED_EDGE('',*,*,#24264,.T.); -#45217=ORIENTED_EDGE('',*,*,#45216,.F.); -#45219=ORIENTED_EDGE('',*,*,#45218,.F.); -#45220=EDGE_LOOP('',(#45211,#45212,#45214,#45215,#45217,#45219)); -#45221=FACE_OUTER_BOUND('',#45220,.F.); -#45223=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45224=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45225=DIRECTION('',(0.E0,0.E0,1.E0)); -#45226=AXIS2_PLACEMENT_3D('',#45223,#45224,#45225); -#45227=PLANE('',#45226); -#45229=ORIENTED_EDGE('',*,*,#45228,.F.); -#45230=ORIENTED_EDGE('',*,*,#22173,.F.); -#45231=ORIENTED_EDGE('',*,*,#45182,.T.); -#45233=ORIENTED_EDGE('',*,*,#45232,.T.); -#45234=ORIENTED_EDGE('',*,*,#45200,.T.); -#45235=ORIENTED_EDGE('',*,*,#24256,.T.); -#45237=ORIENTED_EDGE('',*,*,#45236,.F.); -#45239=ORIENTED_EDGE('',*,*,#45238,.F.); -#45240=EDGE_LOOP('',(#45229,#45230,#45231,#45233,#45234,#45235,#45237,#45239)); -#45241=FACE_OUTER_BOUND('',#45240,.F.); -#45243=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45244=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45245=DIRECTION('',(0.E0,0.E0,1.E0)); -#45246=AXIS2_PLACEMENT_3D('',#45243,#45244,#45245); -#45247=PLANE('',#45246); -#45249=ORIENTED_EDGE('',*,*,#45248,.F.); -#45250=ORIENTED_EDGE('',*,*,#22181,.F.); -#45252=ORIENTED_EDGE('',*,*,#45251,.T.); -#45254=ORIENTED_EDGE('',*,*,#45253,.T.); -#45256=ORIENTED_EDGE('',*,*,#45255,.T.); -#45257=ORIENTED_EDGE('',*,*,#24248,.T.); -#45259=ORIENTED_EDGE('',*,*,#45258,.F.); -#45261=ORIENTED_EDGE('',*,*,#45260,.F.); -#45262=EDGE_LOOP('',(#45249,#45250,#45252,#45254,#45256,#45257,#45259,#45261)); -#45263=FACE_OUTER_BOUND('',#45262,.F.); -#45265=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45266=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45267=DIRECTION('',(0.E0,0.E0,1.E0)); -#45268=AXIS2_PLACEMENT_3D('',#45265,#45266,#45267); -#45269=PLANE('',#45268); -#45271=ORIENTED_EDGE('',*,*,#45270,.F.); -#45272=ORIENTED_EDGE('',*,*,#22189,.F.); -#45274=ORIENTED_EDGE('',*,*,#45273,.T.); -#45276=ORIENTED_EDGE('',*,*,#45275,.T.); -#45278=ORIENTED_EDGE('',*,*,#45277,.T.); -#45279=ORIENTED_EDGE('',*,*,#24240,.T.); -#45281=ORIENTED_EDGE('',*,*,#45280,.F.); -#45283=ORIENTED_EDGE('',*,*,#45282,.F.); -#45284=EDGE_LOOP('',(#45271,#45272,#45274,#45276,#45278,#45279,#45281,#45283)); -#45285=FACE_OUTER_BOUND('',#45284,.F.); -#45287=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45288=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45289=DIRECTION('',(0.E0,0.E0,1.E0)); -#45290=AXIS2_PLACEMENT_3D('',#45287,#45288,#45289); -#45291=PLANE('',#45290); -#45293=ORIENTED_EDGE('',*,*,#45292,.F.); -#45294=ORIENTED_EDGE('',*,*,#22197,.F.); -#45296=ORIENTED_EDGE('',*,*,#45295,.T.); -#45298=ORIENTED_EDGE('',*,*,#45297,.T.); -#45300=ORIENTED_EDGE('',*,*,#45299,.T.); -#45301=ORIENTED_EDGE('',*,*,#24232,.T.); -#45303=ORIENTED_EDGE('',*,*,#45302,.F.); -#45305=ORIENTED_EDGE('',*,*,#45304,.F.); -#45306=EDGE_LOOP('',(#45293,#45294,#45296,#45298,#45300,#45301,#45303,#45305)); -#45307=FACE_OUTER_BOUND('',#45306,.F.); -#45309=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45310=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45311=DIRECTION('',(0.E0,0.E0,1.E0)); -#45312=AXIS2_PLACEMENT_3D('',#45309,#45310,#45311); -#45313=PLANE('',#45312); -#45315=ORIENTED_EDGE('',*,*,#45314,.F.); -#45316=ORIENTED_EDGE('',*,*,#22205,.F.); -#45318=ORIENTED_EDGE('',*,*,#45317,.T.); -#45320=ORIENTED_EDGE('',*,*,#45319,.T.); -#45322=ORIENTED_EDGE('',*,*,#45321,.T.); -#45323=ORIENTED_EDGE('',*,*,#24224,.T.); -#45325=ORIENTED_EDGE('',*,*,#45324,.F.); -#45327=ORIENTED_EDGE('',*,*,#45326,.F.); -#45328=EDGE_LOOP('',(#45315,#45316,#45318,#45320,#45322,#45323,#45325,#45327)); -#45329=FACE_OUTER_BOUND('',#45328,.F.); -#45331=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45332=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45333=DIRECTION('',(0.E0,0.E0,1.E0)); -#45334=AXIS2_PLACEMENT_3D('',#45331,#45332,#45333); -#45335=PLANE('',#45334); -#45337=ORIENTED_EDGE('',*,*,#45336,.F.); -#45338=ORIENTED_EDGE('',*,*,#22213,.F.); -#45340=ORIENTED_EDGE('',*,*,#45339,.T.); -#45342=ORIENTED_EDGE('',*,*,#45341,.T.); -#45344=ORIENTED_EDGE('',*,*,#45343,.T.); -#45345=ORIENTED_EDGE('',*,*,#24216,.T.); -#45347=ORIENTED_EDGE('',*,*,#45346,.F.); -#45349=ORIENTED_EDGE('',*,*,#45348,.F.); -#45350=EDGE_LOOP('',(#45337,#45338,#45340,#45342,#45344,#45345,#45347,#45349)); -#45351=FACE_OUTER_BOUND('',#45350,.F.); -#45353=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45354=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45355=DIRECTION('',(0.E0,0.E0,1.E0)); -#45356=AXIS2_PLACEMENT_3D('',#45353,#45354,#45355); -#45357=PLANE('',#45356); -#45359=ORIENTED_EDGE('',*,*,#45358,.F.); -#45360=ORIENTED_EDGE('',*,*,#22221,.F.); -#45362=ORIENTED_EDGE('',*,*,#45361,.T.); -#45364=ORIENTED_EDGE('',*,*,#45363,.T.); -#45366=ORIENTED_EDGE('',*,*,#45365,.T.); -#45367=ORIENTED_EDGE('',*,*,#24208,.T.); -#45369=ORIENTED_EDGE('',*,*,#45368,.F.); -#45371=ORIENTED_EDGE('',*,*,#45370,.F.); -#45372=EDGE_LOOP('',(#45359,#45360,#45362,#45364,#45366,#45367,#45369,#45371)); -#45373=FACE_OUTER_BOUND('',#45372,.F.); -#45375=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.E0)); -#45376=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45377=DIRECTION('',(0.E0,0.E0,1.E0)); -#45378=AXIS2_PLACEMENT_3D('',#45375,#45376,#45377); -#45379=PLANE('',#45378); -#45381=ORIENTED_EDGE('',*,*,#45380,.T.); -#45382=ORIENTED_EDGE('',*,*,#24200,.T.); -#45384=ORIENTED_EDGE('',*,*,#45383,.F.); -#45385=ORIENTED_EDGE('',*,*,#22229,.F.); -#45387=ORIENTED_EDGE('',*,*,#45386,.T.); -#45389=ORIENTED_EDGE('',*,*,#45388,.T.); -#45390=EDGE_LOOP('',(#45381,#45382,#45384,#45385,#45387,#45389)); -#45391=FACE_OUTER_BOUND('',#45390,.F.); -#45393=CARTESIAN_POINT('',(-5.9E0,3.E-1,4.55E0)); -#45394=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45395=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45396=AXIS2_PLACEMENT_3D('',#45393,#45394,#45395); -#45397=PLANE('',#45396); -#45398=ORIENTED_EDGE('',*,*,#45140,.F.); -#45400=ORIENTED_EDGE('',*,*,#45399,.T.); -#45401=ORIENTED_EDGE('',*,*,#22167,.T.); -#45402=ORIENTED_EDGE('',*,*,#45210,.T.); -#45403=EDGE_LOOP('',(#45398,#45400,#45401,#45402)); -#45404=FACE_OUTER_BOUND('',#45403,.F.); -#45406=CARTESIAN_POINT('',(-5.9E0,3.E-1,4.55E0)); -#45407=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45408=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45409=AXIS2_PLACEMENT_3D('',#45406,#45407,#45408); -#45410=PLANE('',#45409); -#45412=ORIENTED_EDGE('',*,*,#45411,.T.); -#45413=ORIENTED_EDGE('',*,*,#45216,.T.); -#45414=ORIENTED_EDGE('',*,*,#24262,.F.); -#45416=ORIENTED_EDGE('',*,*,#45415,.T.); -#45417=EDGE_LOOP('',(#45412,#45413,#45414,#45416)); -#45418=FACE_OUTER_BOUND('',#45417,.F.); -#45420=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.25E0)); -#45421=DIRECTION('',(1.E0,0.E0,0.E0)); -#45422=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45423=AXIS2_PLACEMENT_3D('',#45420,#45421,#45422); -#45424=PLANE('',#45423); -#45425=ORIENTED_EDGE('',*,*,#45138,.F.); -#45426=ORIENTED_EDGE('',*,*,#45185,.T.); -#45427=ORIENTED_EDGE('',*,*,#22169,.T.); -#45428=ORIENTED_EDGE('',*,*,#45399,.F.); -#45429=EDGE_LOOP('',(#45425,#45426,#45427,#45428)); -#45430=FACE_OUTER_BOUND('',#45429,.F.); -#45432=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.25E0)); -#45433=DIRECTION('',(1.E0,0.E0,0.E0)); -#45434=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45435=AXIS2_PLACEMENT_3D('',#45432,#45433,#45434); -#45436=PLANE('',#45435); -#45438=ORIENTED_EDGE('',*,*,#45437,.T.); -#45439=ORIENTED_EDGE('',*,*,#45415,.F.); -#45440=ORIENTED_EDGE('',*,*,#24260,.F.); -#45441=ORIENTED_EDGE('',*,*,#45197,.T.); -#45442=EDGE_LOOP('',(#45438,#45439,#45440,#45441)); -#45443=FACE_OUTER_BOUND('',#45442,.F.); -#45445=CARTESIAN_POINT('',(0.E0,2.5E-1,0.E0)); -#45446=DIRECTION('',(0.E0,1.E0,0.E0)); -#45447=DIRECTION('',(1.E0,0.E0,0.E0)); -#45448=AXIS2_PLACEMENT_3D('',#45445,#45446,#45447); -#45449=PLANE('',#45448); -#45450=ORIENTED_EDGE('',*,*,#45195,.F.); -#45452=ORIENTED_EDGE('',*,*,#45451,.F.); -#45453=ORIENTED_EDGE('',*,*,#45411,.F.); -#45454=ORIENTED_EDGE('',*,*,#45437,.F.); -#45455=EDGE_LOOP('',(#45450,#45452,#45453,#45454)); -#45456=FACE_OUTER_BOUND('',#45455,.F.); -#45458=FILL_AREA_STYLE_COLOUR('',#15); -#45459=FILL_AREA_STYLE('',(#45458)); -#45460=SURFACE_STYLE_FILL_AREA(#45459); -#45461=SURFACE_SIDE_STYLE('',(#45460)); -#45462=SURFACE_STYLE_USAGE(.POSITIVE.,#45461); -#45463=PRESENTATION_STYLE_ASSIGNMENT((#45462)); -#45464=STYLED_ITEM('',(#45463),#45457); -#45465=CARTESIAN_POINT('',(0.E0,2.5E-1,0.E0)); -#45466=DIRECTION('',(0.E0,1.E0,0.E0)); -#45467=DIRECTION('',(1.E0,0.E0,0.E0)); -#45468=AXIS2_PLACEMENT_3D('',#45465,#45466,#45467); -#45469=PLANE('',#45468); -#45470=ORIENTED_EDGE('',*,*,#45122,.F.); -#45472=ORIENTED_EDGE('',*,*,#45471,.F.); -#45474=ORIENTED_EDGE('',*,*,#45473,.F.); -#45476=ORIENTED_EDGE('',*,*,#45475,.F.); -#45477=EDGE_LOOP('',(#45470,#45472,#45474,#45476)); -#45478=FACE_OUTER_BOUND('',#45477,.F.); -#45480=FILL_AREA_STYLE_COLOUR('',#15); -#45481=FILL_AREA_STYLE('',(#45480)); -#45482=SURFACE_STYLE_FILL_AREA(#45481); -#45483=SURFACE_SIDE_STYLE('',(#45482)); -#45484=SURFACE_STYLE_USAGE(.POSITIVE.,#45483); -#45485=PRESENTATION_STYLE_ASSIGNMENT((#45484)); -#45486=STYLED_ITEM('',(#45485),#45479); -#45487=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,4.9E0)); -#45488=DIRECTION('',(0.E0,1.E0,0.E0)); -#45489=DIRECTION('',(1.E0,0.E0,0.E0)); -#45490=AXIS2_PLACEMENT_3D('',#45487,#45488,#45489); -#45491=CYLINDRICAL_SURFACE('',#45490,4.E-1); -#45492=ORIENTED_EDGE('',*,*,#45218,.T.); -#45493=ORIENTED_EDGE('',*,*,#45451,.T.); -#45494=ORIENTED_EDGE('',*,*,#45232,.F.); -#45495=ORIENTED_EDGE('',*,*,#45142,.F.); -#45496=EDGE_LOOP('',(#45492,#45493,#45494,#45495)); -#45497=FACE_OUTER_BOUND('',#45496,.F.); -#45499=FILL_AREA_STYLE_COLOUR('',#15); -#45500=FILL_AREA_STYLE('',(#45499)); -#45501=SURFACE_STYLE_FILL_AREA(#45500); -#45502=SURFACE_SIDE_STYLE('',(#45501)); -#45503=SURFACE_STYLE_USAGE(.NEGATIVE.,#45502); -#45504=PRESENTATION_STYLE_ASSIGNMENT((#45503)); -#45505=STYLED_ITEM('',(#45504),#45498); -#45506=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,4.9E0)); -#45507=DIRECTION('',(0.E0,1.E0,0.E0)); -#45508=DIRECTION('',(1.E0,0.E0,0.E0)); -#45509=AXIS2_PLACEMENT_3D('',#45506,#45507,#45508); -#45510=CYLINDRICAL_SURFACE('',#45509,4.E-1); -#45511=ORIENTED_EDGE('',*,*,#44926,.F.); -#45512=ORIENTED_EDGE('',*,*,#45164,.F.); -#45513=ORIENTED_EDGE('',*,*,#44941,.T.); -#45514=ORIENTED_EDGE('',*,*,#45471,.T.); -#45515=EDGE_LOOP('',(#45511,#45512,#45513,#45514)); -#45516=FACE_OUTER_BOUND('',#45515,.F.); -#45518=FILL_AREA_STYLE_COLOUR('',#15); -#45519=FILL_AREA_STYLE('',(#45518)); -#45520=SURFACE_STYLE_FILL_AREA(#45519); -#45521=SURFACE_SIDE_STYLE('',(#45520)); -#45522=SURFACE_STYLE_USAGE(.NEGATIVE.,#45521); -#45523=PRESENTATION_STYLE_ASSIGNMENT((#45522)); -#45524=STYLED_ITEM('',(#45523),#45517); -#45525=CARTESIAN_POINT('',(6.9E0,3.E-1,5.25E0)); -#45526=DIRECTION('',(0.E0,0.E0,1.E0)); -#45527=DIRECTION('',(1.E0,0.E0,0.E0)); -#45528=AXIS2_PLACEMENT_3D('',#45525,#45526,#45527); -#45529=PLANE('',#45528); -#45530=ORIENTED_EDGE('',*,*,#45162,.F.); -#45532=ORIENTED_EDGE('',*,*,#45531,.T.); -#45533=ORIENTED_EDGE('',*,*,#22291,.F.); -#45534=ORIENTED_EDGE('',*,*,#44943,.T.); -#45535=EDGE_LOOP('',(#45530,#45532,#45533,#45534)); -#45536=FACE_OUTER_BOUND('',#45535,.F.); -#45538=CARTESIAN_POINT('',(6.9E0,3.E-1,5.25E0)); -#45539=DIRECTION('',(0.E0,0.E0,1.E0)); -#45540=DIRECTION('',(1.E0,0.E0,0.E0)); -#45541=AXIS2_PLACEMENT_3D('',#45538,#45539,#45540); -#45542=PLANE('',#45541); -#45543=ORIENTED_EDGE('',*,*,#45473,.T.); -#45544=ORIENTED_EDGE('',*,*,#44939,.T.); -#45545=ORIENTED_EDGE('',*,*,#24138,.T.); -#45547=ORIENTED_EDGE('',*,*,#45546,.T.); -#45548=EDGE_LOOP('',(#45543,#45544,#45545,#45547)); -#45549=FACE_OUTER_BOUND('',#45548,.F.); -#45551=CARTESIAN_POINT('',(6.9E0,3.E-1,4.55E0)); -#45552=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45553=DIRECTION('',(0.E0,0.E0,1.E0)); -#45554=AXIS2_PLACEMENT_3D('',#45551,#45552,#45553); -#45555=PLANE('',#45554); -#45556=ORIENTED_EDGE('',*,*,#45160,.F.); -#45557=ORIENTED_EDGE('',*,*,#45112,.T.); -#45558=ORIENTED_EDGE('',*,*,#22293,.T.); -#45559=ORIENTED_EDGE('',*,*,#45531,.F.); -#45560=EDGE_LOOP('',(#45556,#45557,#45558,#45559)); -#45561=FACE_OUTER_BOUND('',#45560,.F.); -#45563=CARTESIAN_POINT('',(6.9E0,3.E-1,4.55E0)); -#45564=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45565=DIRECTION('',(0.E0,0.E0,1.E0)); -#45566=AXIS2_PLACEMENT_3D('',#45563,#45564,#45565); -#45567=PLANE('',#45566); -#45568=ORIENTED_EDGE('',*,*,#45475,.T.); -#45569=ORIENTED_EDGE('',*,*,#45546,.F.); -#45570=ORIENTED_EDGE('',*,*,#24136,.F.); -#45571=ORIENTED_EDGE('',*,*,#45124,.T.); -#45572=EDGE_LOOP('',(#45568,#45569,#45570,#45571)); -#45573=FACE_OUTER_BOUND('',#45572,.F.); -#45575=CARTESIAN_POINT('',(-7.5E0,-3.E-1,1.E0)); -#45576=DIRECTION('',(0.E0,0.E0,1.E0)); -#45577=DIRECTION('',(1.E0,0.E0,0.E0)); -#45578=AXIS2_PLACEMENT_3D('',#45575,#45576,#45577); -#45579=PLANE('',#45578); -#45580=ORIENTED_EDGE('',*,*,#22163,.F.); -#45581=ORIENTED_EDGE('',*,*,#23919,.T.); -#45582=ORIENTED_EDGE('',*,*,#24266,.T.); -#45583=ORIENTED_EDGE('',*,*,#45213,.F.); -#45584=EDGE_LOOP('',(#45580,#45581,#45582,#45583)); -#45585=FACE_OUTER_BOUND('',#45584,.F.); -#45587=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.65E0)); -#45588=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45589=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45590=AXIS2_PLACEMENT_3D('',#45587,#45588,#45589); -#45591=PLANE('',#45590); -#45593=ORIENTED_EDGE('',*,*,#45592,.F.); -#45595=ORIENTED_EDGE('',*,*,#45594,.T.); -#45596=ORIENTED_EDGE('',*,*,#22175,.T.); -#45597=ORIENTED_EDGE('',*,*,#45228,.T.); -#45598=EDGE_LOOP('',(#45593,#45595,#45596,#45597)); -#45599=FACE_OUTER_BOUND('',#45598,.F.); -#45601=CARTESIAN_POINT('',(-5.9E0,3.E-1,5.65E0)); -#45602=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45603=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45604=AXIS2_PLACEMENT_3D('',#45601,#45602,#45603); -#45605=PLANE('',#45604); -#45607=ORIENTED_EDGE('',*,*,#45606,.T.); -#45608=ORIENTED_EDGE('',*,*,#45236,.T.); -#45609=ORIENTED_EDGE('',*,*,#24254,.F.); -#45611=ORIENTED_EDGE('',*,*,#45610,.T.); -#45612=EDGE_LOOP('',(#45607,#45608,#45609,#45611)); -#45613=FACE_OUTER_BOUND('',#45612,.F.); -#45615=CARTESIAN_POINT('',(0.E0,-2.5E-1,1.1E0)); -#45616=DIRECTION('',(0.E0,1.E0,0.E0)); -#45617=DIRECTION('',(1.E0,0.E0,0.E0)); -#45618=AXIS2_PLACEMENT_3D('',#45615,#45616,#45617); -#45619=PLANE('',#45618); -#45621=ORIENTED_EDGE('',*,*,#45620,.T.); -#45623=ORIENTED_EDGE('',*,*,#45622,.T.); -#45624=ORIENTED_EDGE('',*,*,#45592,.T.); -#45626=ORIENTED_EDGE('',*,*,#45625,.T.); -#45627=EDGE_LOOP('',(#45621,#45623,#45624,#45626)); -#45628=FACE_OUTER_BOUND('',#45627,.F.); -#45630=FILL_AREA_STYLE_COLOUR('',#15); -#45631=FILL_AREA_STYLE('',(#45630)); -#45632=SURFACE_STYLE_FILL_AREA(#45631); -#45633=SURFACE_SIDE_STYLE('',(#45632)); -#45634=SURFACE_STYLE_USAGE(.NEGATIVE.,#45633); -#45635=PRESENTATION_STYLE_ASSIGNMENT((#45634)); -#45636=STYLED_ITEM('',(#45635),#45629); -#45637=CARTESIAN_POINT('',(0.E0,-2.5E-1,1.1E0)); -#45638=DIRECTION('',(0.E0,1.E0,0.E0)); -#45639=DIRECTION('',(1.E0,0.E0,0.E0)); -#45640=AXIS2_PLACEMENT_3D('',#45637,#45638,#45639); -#45641=PLANE('',#45640); -#45643=ORIENTED_EDGE('',*,*,#45642,.T.); -#45645=ORIENTED_EDGE('',*,*,#45644,.T.); -#45647=ORIENTED_EDGE('',*,*,#45646,.T.); -#45649=ORIENTED_EDGE('',*,*,#45648,.T.); -#45650=EDGE_LOOP('',(#45643,#45645,#45647,#45649)); -#45651=FACE_OUTER_BOUND('',#45650,.F.); -#45653=FILL_AREA_STYLE_COLOUR('',#15); -#45654=FILL_AREA_STYLE('',(#45653)); -#45655=SURFACE_STYLE_FILL_AREA(#45654); -#45656=SURFACE_SIDE_STYLE('',(#45655)); -#45657=SURFACE_STYLE_USAGE(.NEGATIVE.,#45656); -#45658=PRESENTATION_STYLE_ASSIGNMENT((#45657)); -#45659=STYLED_ITEM('',(#45658),#45652); -#45660=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,6.35E0)); -#45661=DIRECTION('',(0.E0,0.E0,1.E0)); -#45662=DIRECTION('',(1.E0,0.E0,0.E0)); -#45663=AXIS2_PLACEMENT_3D('',#45660,#45661,#45662); -#45664=PLANE('',#45663); -#45665=ORIENTED_EDGE('',*,*,#45620,.F.); -#45666=ORIENTED_EDGE('',*,*,#45251,.F.); -#45667=ORIENTED_EDGE('',*,*,#22179,.T.); -#45669=ORIENTED_EDGE('',*,*,#45668,.F.); -#45670=EDGE_LOOP('',(#45665,#45666,#45667,#45669)); -#45671=FACE_OUTER_BOUND('',#45670,.F.); -#45673=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,6.35E0)); -#45674=DIRECTION('',(0.E0,0.E0,1.E0)); -#45675=DIRECTION('',(1.E0,0.E0,0.E0)); -#45676=AXIS2_PLACEMENT_3D('',#45673,#45674,#45675); -#45677=PLANE('',#45676); -#45679=ORIENTED_EDGE('',*,*,#45678,.T.); -#45681=ORIENTED_EDGE('',*,*,#45680,.F.); -#45682=ORIENTED_EDGE('',*,*,#24250,.F.); -#45683=ORIENTED_EDGE('',*,*,#45255,.F.); -#45684=EDGE_LOOP('',(#45679,#45681,#45682,#45683)); -#45685=FACE_OUTER_BOUND('',#45684,.F.); -#45687=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.35E0)); -#45688=DIRECTION('',(1.E0,0.E0,0.E0)); -#45689=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45690=AXIS2_PLACEMENT_3D('',#45687,#45688,#45689); -#45691=PLANE('',#45690); -#45692=ORIENTED_EDGE('',*,*,#45622,.F.); -#45693=ORIENTED_EDGE('',*,*,#45668,.T.); -#45694=ORIENTED_EDGE('',*,*,#22177,.T.); -#45695=ORIENTED_EDGE('',*,*,#45594,.F.); -#45696=EDGE_LOOP('',(#45692,#45693,#45694,#45695)); -#45697=FACE_OUTER_BOUND('',#45696,.F.); -#45699=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.35E0)); -#45700=DIRECTION('',(1.E0,0.E0,0.E0)); -#45701=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45702=AXIS2_PLACEMENT_3D('',#45699,#45700,#45701); -#45703=PLANE('',#45702); -#45705=ORIENTED_EDGE('',*,*,#45704,.T.); -#45706=ORIENTED_EDGE('',*,*,#45610,.F.); -#45707=ORIENTED_EDGE('',*,*,#24252,.F.); -#45708=ORIENTED_EDGE('',*,*,#45680,.T.); -#45709=EDGE_LOOP('',(#45705,#45706,#45707,#45708)); -#45710=FACE_OUTER_BOUND('',#45709,.F.); -#45712=CARTESIAN_POINT('',(0.E0,2.5E-1,1.1E0)); -#45713=DIRECTION('',(0.E0,1.E0,0.E0)); -#45714=DIRECTION('',(1.E0,0.E0,0.E0)); -#45715=AXIS2_PLACEMENT_3D('',#45712,#45713,#45714); -#45716=PLANE('',#45715); -#45717=ORIENTED_EDGE('',*,*,#45678,.F.); -#45719=ORIENTED_EDGE('',*,*,#45718,.F.); -#45720=ORIENTED_EDGE('',*,*,#45606,.F.); -#45721=ORIENTED_EDGE('',*,*,#45704,.F.); -#45722=EDGE_LOOP('',(#45717,#45719,#45720,#45721)); -#45723=FACE_OUTER_BOUND('',#45722,.F.); -#45725=FILL_AREA_STYLE_COLOUR('',#15); -#45726=FILL_AREA_STYLE('',(#45725)); -#45727=SURFACE_STYLE_FILL_AREA(#45726); -#45728=SURFACE_SIDE_STYLE('',(#45727)); -#45729=SURFACE_STYLE_USAGE(.POSITIVE.,#45728); -#45730=PRESENTATION_STYLE_ASSIGNMENT((#45729)); -#45731=STYLED_ITEM('',(#45730),#45724); -#45732=CARTESIAN_POINT('',(0.E0,2.5E-1,1.1E0)); -#45733=DIRECTION('',(0.E0,1.E0,0.E0)); -#45734=DIRECTION('',(1.E0,0.E0,0.E0)); -#45735=AXIS2_PLACEMENT_3D('',#45732,#45733,#45734); -#45736=PLANE('',#45735); -#45738=ORIENTED_EDGE('',*,*,#45737,.F.); -#45740=ORIENTED_EDGE('',*,*,#45739,.F.); -#45742=ORIENTED_EDGE('',*,*,#45741,.F.); -#45744=ORIENTED_EDGE('',*,*,#45743,.F.); -#45745=EDGE_LOOP('',(#45738,#45740,#45742,#45744)); -#45746=FACE_OUTER_BOUND('',#45745,.F.); -#45748=FILL_AREA_STYLE_COLOUR('',#15); -#45749=FILL_AREA_STYLE('',(#45748)); -#45750=SURFACE_STYLE_FILL_AREA(#45749); -#45751=SURFACE_SIDE_STYLE('',(#45750)); -#45752=SURFACE_STYLE_USAGE(.POSITIVE.,#45751); -#45753=PRESENTATION_STYLE_ASSIGNMENT((#45752)); -#45754=STYLED_ITEM('',(#45753),#45747); -#45755=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,6.E0)); -#45756=DIRECTION('',(0.E0,1.E0,0.E0)); -#45757=DIRECTION('',(1.E0,0.E0,0.E0)); -#45758=AXIS2_PLACEMENT_3D('',#45755,#45756,#45757); -#45759=CYLINDRICAL_SURFACE('',#45758,4.E-1); -#45760=ORIENTED_EDGE('',*,*,#45238,.T.); -#45761=ORIENTED_EDGE('',*,*,#45718,.T.); -#45762=ORIENTED_EDGE('',*,*,#45253,.F.); -#45763=ORIENTED_EDGE('',*,*,#45625,.F.); -#45764=EDGE_LOOP('',(#45760,#45761,#45762,#45763)); -#45765=FACE_OUTER_BOUND('',#45764,.F.); -#45767=FILL_AREA_STYLE_COLOUR('',#15); -#45768=FILL_AREA_STYLE('',(#45767)); -#45769=SURFACE_STYLE_FILL_AREA(#45768); -#45770=SURFACE_SIDE_STYLE('',(#45769)); -#45771=SURFACE_STYLE_USAGE(.NEGATIVE.,#45770); -#45772=PRESENTATION_STYLE_ASSIGNMENT((#45771)); -#45773=STYLED_ITEM('',(#45772),#45766); -#45774=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,5.65E0)); -#45775=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45776=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45777=AXIS2_PLACEMENT_3D('',#45774,#45775,#45776); -#45778=PLANE('',#45777); -#45779=ORIENTED_EDGE('',*,*,#45642,.F.); -#45780=ORIENTED_EDGE('',*,*,#44946,.F.); -#45781=ORIENTED_EDGE('',*,*,#22287,.T.); -#45783=ORIENTED_EDGE('',*,*,#45782,.F.); -#45784=EDGE_LOOP('',(#45779,#45780,#45781,#45783)); -#45785=FACE_OUTER_BOUND('',#45784,.F.); -#45787=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,5.65E0)); -#45788=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45789=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45790=AXIS2_PLACEMENT_3D('',#45787,#45788,#45789); -#45791=PLANE('',#45790); -#45792=ORIENTED_EDGE('',*,*,#45737,.T.); -#45794=ORIENTED_EDGE('',*,*,#45793,.F.); -#45795=ORIENTED_EDGE('',*,*,#24142,.F.); -#45796=ORIENTED_EDGE('',*,*,#44936,.F.); -#45797=EDGE_LOOP('',(#45792,#45794,#45795,#45796)); -#45798=FACE_OUTER_BOUND('',#45797,.F.); -#45800=CARTESIAN_POINT('',(6.9E0,3.E-1,5.65E0)); -#45801=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45802=DIRECTION('',(0.E0,0.E0,1.E0)); -#45803=AXIS2_PLACEMENT_3D('',#45800,#45801,#45802); -#45804=PLANE('',#45803); -#45805=ORIENTED_EDGE('',*,*,#45644,.F.); -#45806=ORIENTED_EDGE('',*,*,#45782,.T.); -#45807=ORIENTED_EDGE('',*,*,#22285,.T.); -#45809=ORIENTED_EDGE('',*,*,#45808,.F.); -#45810=EDGE_LOOP('',(#45805,#45806,#45807,#45809)); -#45811=FACE_OUTER_BOUND('',#45810,.F.); -#45813=CARTESIAN_POINT('',(6.9E0,3.E-1,5.65E0)); -#45814=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45815=DIRECTION('',(0.E0,0.E0,1.E0)); -#45816=AXIS2_PLACEMENT_3D('',#45813,#45814,#45815); -#45817=PLANE('',#45816); -#45818=ORIENTED_EDGE('',*,*,#45743,.T.); -#45820=ORIENTED_EDGE('',*,*,#45819,.F.); -#45821=ORIENTED_EDGE('',*,*,#24144,.F.); -#45822=ORIENTED_EDGE('',*,*,#45793,.T.); -#45823=EDGE_LOOP('',(#45818,#45820,#45821,#45822)); -#45824=FACE_OUTER_BOUND('',#45823,.F.); -#45826=CARTESIAN_POINT('',(6.9E0,3.E-1,6.35E0)); -#45827=DIRECTION('',(0.E0,0.E0,1.E0)); -#45828=DIRECTION('',(1.E0,0.E0,0.E0)); -#45829=AXIS2_PLACEMENT_3D('',#45826,#45827,#45828); -#45830=PLANE('',#45829); -#45831=ORIENTED_EDGE('',*,*,#45646,.F.); -#45832=ORIENTED_EDGE('',*,*,#45808,.T.); -#45833=ORIENTED_EDGE('',*,*,#22283,.F.); -#45834=ORIENTED_EDGE('',*,*,#44965,.T.); -#45835=EDGE_LOOP('',(#45831,#45832,#45833,#45834)); -#45836=FACE_OUTER_BOUND('',#45835,.F.); -#45838=CARTESIAN_POINT('',(6.9E0,3.E-1,6.35E0)); -#45839=DIRECTION('',(0.E0,0.E0,1.E0)); -#45840=DIRECTION('',(1.E0,0.E0,0.E0)); -#45841=AXIS2_PLACEMENT_3D('',#45838,#45839,#45840); -#45842=PLANE('',#45841); -#45843=ORIENTED_EDGE('',*,*,#45741,.T.); -#45844=ORIENTED_EDGE('',*,*,#44961,.T.); -#45845=ORIENTED_EDGE('',*,*,#24146,.T.); -#45846=ORIENTED_EDGE('',*,*,#45819,.T.); -#45847=EDGE_LOOP('',(#45843,#45844,#45845,#45846)); -#45848=FACE_OUTER_BOUND('',#45847,.F.); -#45850=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,6.E0)); -#45851=DIRECTION('',(0.E0,1.E0,0.E0)); -#45852=DIRECTION('',(1.E0,0.E0,0.E0)); -#45853=AXIS2_PLACEMENT_3D('',#45850,#45851,#45852); -#45854=CYLINDRICAL_SURFACE('',#45853,4.E-1); -#45855=ORIENTED_EDGE('',*,*,#44948,.F.); -#45856=ORIENTED_EDGE('',*,*,#45648,.F.); -#45857=ORIENTED_EDGE('',*,*,#44963,.T.); -#45858=ORIENTED_EDGE('',*,*,#45739,.T.); -#45859=EDGE_LOOP('',(#45855,#45856,#45857,#45858)); -#45860=FACE_OUTER_BOUND('',#45859,.F.); -#45862=FILL_AREA_STYLE_COLOUR('',#15); -#45863=FILL_AREA_STYLE('',(#45862)); -#45864=SURFACE_STYLE_FILL_AREA(#45863); -#45865=SURFACE_SIDE_STYLE('',(#45864)); -#45866=SURFACE_STYLE_USAGE(.NEGATIVE.,#45865); -#45867=PRESENTATION_STYLE_ASSIGNMENT((#45866)); -#45868=STYLED_ITEM('',(#45867),#45861); -#45869=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.75E0)); -#45870=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45871=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45872=AXIS2_PLACEMENT_3D('',#45869,#45870,#45871); -#45873=PLANE('',#45872); -#45875=ORIENTED_EDGE('',*,*,#45874,.F.); -#45877=ORIENTED_EDGE('',*,*,#45876,.T.); -#45878=ORIENTED_EDGE('',*,*,#22183,.T.); -#45879=ORIENTED_EDGE('',*,*,#45248,.T.); -#45880=EDGE_LOOP('',(#45875,#45877,#45878,#45879)); -#45881=FACE_OUTER_BOUND('',#45880,.F.); -#45883=CARTESIAN_POINT('',(-5.9E0,3.E-1,6.75E0)); -#45884=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45885=DIRECTION('',(-1.E0,0.E0,0.E0)); -#45886=AXIS2_PLACEMENT_3D('',#45883,#45884,#45885); -#45887=PLANE('',#45886); -#45889=ORIENTED_EDGE('',*,*,#45888,.T.); -#45890=ORIENTED_EDGE('',*,*,#45258,.T.); -#45891=ORIENTED_EDGE('',*,*,#24246,.F.); -#45893=ORIENTED_EDGE('',*,*,#45892,.T.); -#45894=EDGE_LOOP('',(#45889,#45890,#45891,#45893)); -#45895=FACE_OUTER_BOUND('',#45894,.F.); -#45897=CARTESIAN_POINT('',(0.E0,-2.5E-1,2.2E0)); -#45898=DIRECTION('',(0.E0,1.E0,0.E0)); -#45899=DIRECTION('',(1.E0,0.E0,0.E0)); -#45900=AXIS2_PLACEMENT_3D('',#45897,#45898,#45899); -#45901=PLANE('',#45900); -#45903=ORIENTED_EDGE('',*,*,#45902,.T.); -#45905=ORIENTED_EDGE('',*,*,#45904,.T.); -#45906=ORIENTED_EDGE('',*,*,#45874,.T.); -#45908=ORIENTED_EDGE('',*,*,#45907,.T.); -#45909=EDGE_LOOP('',(#45903,#45905,#45906,#45908)); -#45910=FACE_OUTER_BOUND('',#45909,.F.); -#45912=FILL_AREA_STYLE_COLOUR('',#15); -#45913=FILL_AREA_STYLE('',(#45912)); -#45914=SURFACE_STYLE_FILL_AREA(#45913); -#45915=SURFACE_SIDE_STYLE('',(#45914)); -#45916=SURFACE_STYLE_USAGE(.NEGATIVE.,#45915); -#45917=PRESENTATION_STYLE_ASSIGNMENT((#45916)); -#45918=STYLED_ITEM('',(#45917),#45911); -#45919=CARTESIAN_POINT('',(0.E0,-2.5E-1,2.2E0)); -#45920=DIRECTION('',(0.E0,1.E0,0.E0)); -#45921=DIRECTION('',(1.E0,0.E0,0.E0)); -#45922=AXIS2_PLACEMENT_3D('',#45919,#45920,#45921); -#45923=PLANE('',#45922); -#45925=ORIENTED_EDGE('',*,*,#45924,.T.); -#45927=ORIENTED_EDGE('',*,*,#45926,.T.); -#45929=ORIENTED_EDGE('',*,*,#45928,.T.); -#45931=ORIENTED_EDGE('',*,*,#45930,.T.); -#45932=EDGE_LOOP('',(#45925,#45927,#45929,#45931)); -#45933=FACE_OUTER_BOUND('',#45932,.F.); -#45935=FILL_AREA_STYLE_COLOUR('',#15); -#45936=FILL_AREA_STYLE('',(#45935)); -#45937=SURFACE_STYLE_FILL_AREA(#45936); -#45938=SURFACE_SIDE_STYLE('',(#45937)); -#45939=SURFACE_STYLE_USAGE(.NEGATIVE.,#45938); -#45940=PRESENTATION_STYLE_ASSIGNMENT((#45939)); -#45941=STYLED_ITEM('',(#45940),#45934); -#45942=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,7.45E0)); -#45943=DIRECTION('',(0.E0,0.E0,1.E0)); -#45944=DIRECTION('',(1.E0,0.E0,0.E0)); -#45945=AXIS2_PLACEMENT_3D('',#45942,#45943,#45944); -#45946=PLANE('',#45945); -#45947=ORIENTED_EDGE('',*,*,#45902,.F.); -#45948=ORIENTED_EDGE('',*,*,#45273,.F.); -#45949=ORIENTED_EDGE('',*,*,#22187,.T.); -#45951=ORIENTED_EDGE('',*,*,#45950,.F.); -#45952=EDGE_LOOP('',(#45947,#45948,#45949,#45951)); -#45953=FACE_OUTER_BOUND('',#45952,.F.); -#45955=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,7.45E0)); -#45956=DIRECTION('',(0.E0,0.E0,1.E0)); -#45957=DIRECTION('',(1.E0,0.E0,0.E0)); -#45958=AXIS2_PLACEMENT_3D('',#45955,#45956,#45957); -#45959=PLANE('',#45958); -#45961=ORIENTED_EDGE('',*,*,#45960,.T.); -#45963=ORIENTED_EDGE('',*,*,#45962,.F.); -#45964=ORIENTED_EDGE('',*,*,#24242,.F.); -#45965=ORIENTED_EDGE('',*,*,#45277,.F.); -#45966=EDGE_LOOP('',(#45961,#45963,#45964,#45965)); -#45967=FACE_OUTER_BOUND('',#45966,.F.); -#45969=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.45E0)); -#45970=DIRECTION('',(1.E0,0.E0,0.E0)); -#45971=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45972=AXIS2_PLACEMENT_3D('',#45969,#45970,#45971); -#45973=PLANE('',#45972); -#45974=ORIENTED_EDGE('',*,*,#45904,.F.); -#45975=ORIENTED_EDGE('',*,*,#45950,.T.); -#45976=ORIENTED_EDGE('',*,*,#22185,.T.); -#45977=ORIENTED_EDGE('',*,*,#45876,.F.); -#45978=EDGE_LOOP('',(#45974,#45975,#45976,#45977)); -#45979=FACE_OUTER_BOUND('',#45978,.F.); -#45981=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.45E0)); -#45982=DIRECTION('',(1.E0,0.E0,0.E0)); -#45983=DIRECTION('',(0.E0,0.E0,-1.E0)); -#45984=AXIS2_PLACEMENT_3D('',#45981,#45982,#45983); -#45985=PLANE('',#45984); -#45987=ORIENTED_EDGE('',*,*,#45986,.T.); -#45988=ORIENTED_EDGE('',*,*,#45892,.F.); -#45989=ORIENTED_EDGE('',*,*,#24244,.F.); -#45990=ORIENTED_EDGE('',*,*,#45962,.T.); -#45991=EDGE_LOOP('',(#45987,#45988,#45989,#45990)); -#45992=FACE_OUTER_BOUND('',#45991,.F.); -#45994=CARTESIAN_POINT('',(0.E0,2.5E-1,2.2E0)); -#45995=DIRECTION('',(0.E0,1.E0,0.E0)); -#45996=DIRECTION('',(1.E0,0.E0,0.E0)); -#45997=AXIS2_PLACEMENT_3D('',#45994,#45995,#45996); -#45998=PLANE('',#45997); -#45999=ORIENTED_EDGE('',*,*,#45960,.F.); -#46001=ORIENTED_EDGE('',*,*,#46000,.F.); -#46002=ORIENTED_EDGE('',*,*,#45888,.F.); -#46003=ORIENTED_EDGE('',*,*,#45986,.F.); -#46004=EDGE_LOOP('',(#45999,#46001,#46002,#46003)); -#46005=FACE_OUTER_BOUND('',#46004,.F.); -#46007=FILL_AREA_STYLE_COLOUR('',#15); -#46008=FILL_AREA_STYLE('',(#46007)); -#46009=SURFACE_STYLE_FILL_AREA(#46008); -#46010=SURFACE_SIDE_STYLE('',(#46009)); -#46011=SURFACE_STYLE_USAGE(.POSITIVE.,#46010); -#46012=PRESENTATION_STYLE_ASSIGNMENT((#46011)); -#46013=STYLED_ITEM('',(#46012),#46006); -#46014=CARTESIAN_POINT('',(0.E0,2.5E-1,2.2E0)); -#46015=DIRECTION('',(0.E0,1.E0,0.E0)); -#46016=DIRECTION('',(1.E0,0.E0,0.E0)); -#46017=AXIS2_PLACEMENT_3D('',#46014,#46015,#46016); -#46018=PLANE('',#46017); -#46020=ORIENTED_EDGE('',*,*,#46019,.F.); -#46022=ORIENTED_EDGE('',*,*,#46021,.F.); -#46024=ORIENTED_EDGE('',*,*,#46023,.F.); -#46026=ORIENTED_EDGE('',*,*,#46025,.F.); -#46027=EDGE_LOOP('',(#46020,#46022,#46024,#46026)); -#46028=FACE_OUTER_BOUND('',#46027,.F.); -#46030=FILL_AREA_STYLE_COLOUR('',#15); -#46031=FILL_AREA_STYLE('',(#46030)); -#46032=SURFACE_STYLE_FILL_AREA(#46031); -#46033=SURFACE_SIDE_STYLE('',(#46032)); -#46034=SURFACE_STYLE_USAGE(.POSITIVE.,#46033); -#46035=PRESENTATION_STYLE_ASSIGNMENT((#46034)); -#46036=STYLED_ITEM('',(#46035),#46029); -#46037=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,7.1E0)); -#46038=DIRECTION('',(0.E0,1.E0,0.E0)); -#46039=DIRECTION('',(1.E0,0.E0,0.E0)); -#46040=AXIS2_PLACEMENT_3D('',#46037,#46038,#46039); -#46041=CYLINDRICAL_SURFACE('',#46040,4.E-1); -#46042=ORIENTED_EDGE('',*,*,#45260,.T.); -#46043=ORIENTED_EDGE('',*,*,#46000,.T.); -#46044=ORIENTED_EDGE('',*,*,#45275,.F.); -#46045=ORIENTED_EDGE('',*,*,#45907,.F.); -#46046=EDGE_LOOP('',(#46042,#46043,#46044,#46045)); -#46047=FACE_OUTER_BOUND('',#46046,.F.); -#46049=FILL_AREA_STYLE_COLOUR('',#15); -#46050=FILL_AREA_STYLE('',(#46049)); -#46051=SURFACE_STYLE_FILL_AREA(#46050); -#46052=SURFACE_SIDE_STYLE('',(#46051)); -#46053=SURFACE_STYLE_USAGE(.NEGATIVE.,#46052); -#46054=PRESENTATION_STYLE_ASSIGNMENT((#46053)); -#46055=STYLED_ITEM('',(#46054),#46048); -#46056=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,6.75E0)); -#46057=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46058=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46059=AXIS2_PLACEMENT_3D('',#46056,#46057,#46058); -#46060=PLANE('',#46059); -#46061=ORIENTED_EDGE('',*,*,#45924,.F.); -#46062=ORIENTED_EDGE('',*,*,#44968,.F.); -#46063=ORIENTED_EDGE('',*,*,#22279,.T.); -#46065=ORIENTED_EDGE('',*,*,#46064,.F.); -#46066=EDGE_LOOP('',(#46061,#46062,#46063,#46065)); -#46067=FACE_OUTER_BOUND('',#46066,.F.); -#46069=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,6.75E0)); -#46070=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46071=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46072=AXIS2_PLACEMENT_3D('',#46069,#46070,#46071); -#46073=PLANE('',#46072); -#46074=ORIENTED_EDGE('',*,*,#46019,.T.); -#46076=ORIENTED_EDGE('',*,*,#46075,.F.); -#46077=ORIENTED_EDGE('',*,*,#24150,.F.); -#46078=ORIENTED_EDGE('',*,*,#44958,.F.); -#46079=EDGE_LOOP('',(#46074,#46076,#46077,#46078)); -#46080=FACE_OUTER_BOUND('',#46079,.F.); -#46082=CARTESIAN_POINT('',(6.9E0,3.E-1,6.75E0)); -#46083=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46084=DIRECTION('',(0.E0,0.E0,1.E0)); -#46085=AXIS2_PLACEMENT_3D('',#46082,#46083,#46084); -#46086=PLANE('',#46085); -#46087=ORIENTED_EDGE('',*,*,#45926,.F.); -#46088=ORIENTED_EDGE('',*,*,#46064,.T.); -#46089=ORIENTED_EDGE('',*,*,#22277,.T.); -#46091=ORIENTED_EDGE('',*,*,#46090,.F.); -#46092=EDGE_LOOP('',(#46087,#46088,#46089,#46091)); -#46093=FACE_OUTER_BOUND('',#46092,.F.); -#46095=CARTESIAN_POINT('',(6.9E0,3.E-1,6.75E0)); -#46096=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46097=DIRECTION('',(0.E0,0.E0,1.E0)); -#46098=AXIS2_PLACEMENT_3D('',#46095,#46096,#46097); -#46099=PLANE('',#46098); -#46100=ORIENTED_EDGE('',*,*,#46025,.T.); -#46102=ORIENTED_EDGE('',*,*,#46101,.F.); -#46103=ORIENTED_EDGE('',*,*,#24152,.F.); -#46104=ORIENTED_EDGE('',*,*,#46075,.T.); -#46105=EDGE_LOOP('',(#46100,#46102,#46103,#46104)); -#46106=FACE_OUTER_BOUND('',#46105,.F.); -#46108=CARTESIAN_POINT('',(6.9E0,3.E-1,7.45E0)); -#46109=DIRECTION('',(0.E0,0.E0,1.E0)); -#46110=DIRECTION('',(1.E0,0.E0,0.E0)); -#46111=AXIS2_PLACEMENT_3D('',#46108,#46109,#46110); -#46112=PLANE('',#46111); -#46113=ORIENTED_EDGE('',*,*,#45928,.F.); -#46114=ORIENTED_EDGE('',*,*,#46090,.T.); -#46115=ORIENTED_EDGE('',*,*,#22275,.F.); -#46116=ORIENTED_EDGE('',*,*,#44987,.T.); -#46117=EDGE_LOOP('',(#46113,#46114,#46115,#46116)); -#46118=FACE_OUTER_BOUND('',#46117,.F.); -#46120=CARTESIAN_POINT('',(6.9E0,3.E-1,7.45E0)); -#46121=DIRECTION('',(0.E0,0.E0,1.E0)); -#46122=DIRECTION('',(1.E0,0.E0,0.E0)); -#46123=AXIS2_PLACEMENT_3D('',#46120,#46121,#46122); -#46124=PLANE('',#46123); -#46125=ORIENTED_EDGE('',*,*,#46023,.T.); -#46126=ORIENTED_EDGE('',*,*,#44983,.T.); -#46127=ORIENTED_EDGE('',*,*,#24154,.T.); -#46128=ORIENTED_EDGE('',*,*,#46101,.T.); -#46129=EDGE_LOOP('',(#46125,#46126,#46127,#46128)); -#46130=FACE_OUTER_BOUND('',#46129,.F.); -#46132=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,7.1E0)); -#46133=DIRECTION('',(0.E0,1.E0,0.E0)); -#46134=DIRECTION('',(1.E0,0.E0,0.E0)); -#46135=AXIS2_PLACEMENT_3D('',#46132,#46133,#46134); -#46136=CYLINDRICAL_SURFACE('',#46135,4.E-1); -#46137=ORIENTED_EDGE('',*,*,#44970,.F.); -#46138=ORIENTED_EDGE('',*,*,#45930,.F.); -#46139=ORIENTED_EDGE('',*,*,#44985,.T.); -#46140=ORIENTED_EDGE('',*,*,#46021,.T.); -#46141=EDGE_LOOP('',(#46137,#46138,#46139,#46140)); -#46142=FACE_OUTER_BOUND('',#46141,.F.); -#46144=FILL_AREA_STYLE_COLOUR('',#15); -#46145=FILL_AREA_STYLE('',(#46144)); -#46146=SURFACE_STYLE_FILL_AREA(#46145); -#46147=SURFACE_SIDE_STYLE('',(#46146)); -#46148=SURFACE_STYLE_USAGE(.NEGATIVE.,#46147); -#46149=PRESENTATION_STYLE_ASSIGNMENT((#46148)); -#46150=STYLED_ITEM('',(#46149),#46143); -#46151=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.85E0)); -#46152=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46153=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46154=AXIS2_PLACEMENT_3D('',#46151,#46152,#46153); -#46155=PLANE('',#46154); -#46157=ORIENTED_EDGE('',*,*,#46156,.F.); -#46159=ORIENTED_EDGE('',*,*,#46158,.T.); -#46160=ORIENTED_EDGE('',*,*,#22191,.T.); -#46161=ORIENTED_EDGE('',*,*,#45270,.T.); -#46162=EDGE_LOOP('',(#46157,#46159,#46160,#46161)); -#46163=FACE_OUTER_BOUND('',#46162,.F.); -#46165=CARTESIAN_POINT('',(-5.9E0,3.E-1,7.85E0)); -#46166=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46167=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46168=AXIS2_PLACEMENT_3D('',#46165,#46166,#46167); -#46169=PLANE('',#46168); -#46171=ORIENTED_EDGE('',*,*,#46170,.T.); -#46172=ORIENTED_EDGE('',*,*,#45280,.T.); -#46173=ORIENTED_EDGE('',*,*,#24238,.F.); -#46175=ORIENTED_EDGE('',*,*,#46174,.T.); -#46176=EDGE_LOOP('',(#46171,#46172,#46173,#46175)); -#46177=FACE_OUTER_BOUND('',#46176,.F.); -#46179=CARTESIAN_POINT('',(0.E0,-2.5E-1,3.3E0)); -#46180=DIRECTION('',(0.E0,1.E0,0.E0)); -#46181=DIRECTION('',(1.E0,0.E0,0.E0)); -#46182=AXIS2_PLACEMENT_3D('',#46179,#46180,#46181); -#46183=PLANE('',#46182); -#46185=ORIENTED_EDGE('',*,*,#46184,.T.); -#46187=ORIENTED_EDGE('',*,*,#46186,.T.); -#46188=ORIENTED_EDGE('',*,*,#46156,.T.); -#46190=ORIENTED_EDGE('',*,*,#46189,.T.); -#46191=EDGE_LOOP('',(#46185,#46187,#46188,#46190)); -#46192=FACE_OUTER_BOUND('',#46191,.F.); -#46194=FILL_AREA_STYLE_COLOUR('',#15); -#46195=FILL_AREA_STYLE('',(#46194)); -#46196=SURFACE_STYLE_FILL_AREA(#46195); -#46197=SURFACE_SIDE_STYLE('',(#46196)); -#46198=SURFACE_STYLE_USAGE(.NEGATIVE.,#46197); -#46199=PRESENTATION_STYLE_ASSIGNMENT((#46198)); -#46200=STYLED_ITEM('',(#46199),#46193); -#46201=CARTESIAN_POINT('',(0.E0,-2.5E-1,3.3E0)); -#46202=DIRECTION('',(0.E0,1.E0,0.E0)); -#46203=DIRECTION('',(1.E0,0.E0,0.E0)); -#46204=AXIS2_PLACEMENT_3D('',#46201,#46202,#46203); -#46205=PLANE('',#46204); -#46207=ORIENTED_EDGE('',*,*,#46206,.T.); -#46209=ORIENTED_EDGE('',*,*,#46208,.T.); -#46211=ORIENTED_EDGE('',*,*,#46210,.T.); -#46213=ORIENTED_EDGE('',*,*,#46212,.T.); -#46214=EDGE_LOOP('',(#46207,#46209,#46211,#46213)); -#46215=FACE_OUTER_BOUND('',#46214,.F.); -#46217=FILL_AREA_STYLE_COLOUR('',#15); -#46218=FILL_AREA_STYLE('',(#46217)); -#46219=SURFACE_STYLE_FILL_AREA(#46218); -#46220=SURFACE_SIDE_STYLE('',(#46219)); -#46221=SURFACE_STYLE_USAGE(.NEGATIVE.,#46220); -#46222=PRESENTATION_STYLE_ASSIGNMENT((#46221)); -#46223=STYLED_ITEM('',(#46222),#46216); -#46224=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,8.55E0)); -#46225=DIRECTION('',(0.E0,0.E0,1.E0)); -#46226=DIRECTION('',(1.E0,0.E0,0.E0)); -#46227=AXIS2_PLACEMENT_3D('',#46224,#46225,#46226); -#46228=PLANE('',#46227); -#46229=ORIENTED_EDGE('',*,*,#46184,.F.); -#46230=ORIENTED_EDGE('',*,*,#45295,.F.); -#46231=ORIENTED_EDGE('',*,*,#22195,.T.); -#46233=ORIENTED_EDGE('',*,*,#46232,.F.); -#46234=EDGE_LOOP('',(#46229,#46230,#46231,#46233)); -#46235=FACE_OUTER_BOUND('',#46234,.F.); -#46237=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,8.55E0)); -#46238=DIRECTION('',(0.E0,0.E0,1.E0)); -#46239=DIRECTION('',(1.E0,0.E0,0.E0)); -#46240=AXIS2_PLACEMENT_3D('',#46237,#46238,#46239); -#46241=PLANE('',#46240); -#46243=ORIENTED_EDGE('',*,*,#46242,.T.); -#46245=ORIENTED_EDGE('',*,*,#46244,.F.); -#46246=ORIENTED_EDGE('',*,*,#24234,.F.); -#46247=ORIENTED_EDGE('',*,*,#45299,.F.); -#46248=EDGE_LOOP('',(#46243,#46245,#46246,#46247)); -#46249=FACE_OUTER_BOUND('',#46248,.F.); -#46251=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.55E0)); -#46252=DIRECTION('',(1.E0,0.E0,0.E0)); -#46253=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46254=AXIS2_PLACEMENT_3D('',#46251,#46252,#46253); -#46255=PLANE('',#46254); -#46256=ORIENTED_EDGE('',*,*,#46186,.F.); -#46257=ORIENTED_EDGE('',*,*,#46232,.T.); -#46258=ORIENTED_EDGE('',*,*,#22193,.T.); -#46259=ORIENTED_EDGE('',*,*,#46158,.F.); -#46260=EDGE_LOOP('',(#46256,#46257,#46258,#46259)); -#46261=FACE_OUTER_BOUND('',#46260,.F.); -#46263=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.55E0)); -#46264=DIRECTION('',(1.E0,0.E0,0.E0)); -#46265=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46266=AXIS2_PLACEMENT_3D('',#46263,#46264,#46265); -#46267=PLANE('',#46266); -#46269=ORIENTED_EDGE('',*,*,#46268,.T.); -#46270=ORIENTED_EDGE('',*,*,#46174,.F.); -#46271=ORIENTED_EDGE('',*,*,#24236,.F.); -#46272=ORIENTED_EDGE('',*,*,#46244,.T.); -#46273=EDGE_LOOP('',(#46269,#46270,#46271,#46272)); -#46274=FACE_OUTER_BOUND('',#46273,.F.); -#46276=CARTESIAN_POINT('',(0.E0,2.5E-1,3.3E0)); -#46277=DIRECTION('',(0.E0,1.E0,0.E0)); -#46278=DIRECTION('',(1.E0,0.E0,0.E0)); -#46279=AXIS2_PLACEMENT_3D('',#46276,#46277,#46278); -#46280=PLANE('',#46279); -#46281=ORIENTED_EDGE('',*,*,#46242,.F.); -#46283=ORIENTED_EDGE('',*,*,#46282,.F.); -#46284=ORIENTED_EDGE('',*,*,#46170,.F.); -#46285=ORIENTED_EDGE('',*,*,#46268,.F.); -#46286=EDGE_LOOP('',(#46281,#46283,#46284,#46285)); -#46287=FACE_OUTER_BOUND('',#46286,.F.); -#46289=FILL_AREA_STYLE_COLOUR('',#15); -#46290=FILL_AREA_STYLE('',(#46289)); -#46291=SURFACE_STYLE_FILL_AREA(#46290); -#46292=SURFACE_SIDE_STYLE('',(#46291)); -#46293=SURFACE_STYLE_USAGE(.POSITIVE.,#46292); -#46294=PRESENTATION_STYLE_ASSIGNMENT((#46293)); -#46295=STYLED_ITEM('',(#46294),#46288); -#46296=CARTESIAN_POINT('',(0.E0,2.5E-1,3.3E0)); -#46297=DIRECTION('',(0.E0,1.E0,0.E0)); -#46298=DIRECTION('',(1.E0,0.E0,0.E0)); -#46299=AXIS2_PLACEMENT_3D('',#46296,#46297,#46298); -#46300=PLANE('',#46299); -#46302=ORIENTED_EDGE('',*,*,#46301,.F.); -#46304=ORIENTED_EDGE('',*,*,#46303,.F.); -#46306=ORIENTED_EDGE('',*,*,#46305,.F.); -#46308=ORIENTED_EDGE('',*,*,#46307,.F.); -#46309=EDGE_LOOP('',(#46302,#46304,#46306,#46308)); -#46310=FACE_OUTER_BOUND('',#46309,.F.); -#46312=FILL_AREA_STYLE_COLOUR('',#15); -#46313=FILL_AREA_STYLE('',(#46312)); -#46314=SURFACE_STYLE_FILL_AREA(#46313); -#46315=SURFACE_SIDE_STYLE('',(#46314)); -#46316=SURFACE_STYLE_USAGE(.POSITIVE.,#46315); -#46317=PRESENTATION_STYLE_ASSIGNMENT((#46316)); -#46318=STYLED_ITEM('',(#46317),#46311); -#46319=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,8.2E0)); -#46320=DIRECTION('',(0.E0,1.E0,0.E0)); -#46321=DIRECTION('',(1.E0,0.E0,0.E0)); -#46322=AXIS2_PLACEMENT_3D('',#46319,#46320,#46321); -#46323=CYLINDRICAL_SURFACE('',#46322,4.E-1); -#46324=ORIENTED_EDGE('',*,*,#45282,.T.); -#46325=ORIENTED_EDGE('',*,*,#46282,.T.); -#46326=ORIENTED_EDGE('',*,*,#45297,.F.); -#46327=ORIENTED_EDGE('',*,*,#46189,.F.); -#46328=EDGE_LOOP('',(#46324,#46325,#46326,#46327)); -#46329=FACE_OUTER_BOUND('',#46328,.F.); -#46331=FILL_AREA_STYLE_COLOUR('',#15); -#46332=FILL_AREA_STYLE('',(#46331)); -#46333=SURFACE_STYLE_FILL_AREA(#46332); -#46334=SURFACE_SIDE_STYLE('',(#46333)); -#46335=SURFACE_STYLE_USAGE(.NEGATIVE.,#46334); -#46336=PRESENTATION_STYLE_ASSIGNMENT((#46335)); -#46337=STYLED_ITEM('',(#46336),#46330); -#46338=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,7.85E0)); -#46339=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46340=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46341=AXIS2_PLACEMENT_3D('',#46338,#46339,#46340); -#46342=PLANE('',#46341); -#46343=ORIENTED_EDGE('',*,*,#46206,.F.); -#46344=ORIENTED_EDGE('',*,*,#44990,.F.); -#46345=ORIENTED_EDGE('',*,*,#22271,.T.); -#46347=ORIENTED_EDGE('',*,*,#46346,.F.); -#46348=EDGE_LOOP('',(#46343,#46344,#46345,#46347)); -#46349=FACE_OUTER_BOUND('',#46348,.F.); -#46351=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,7.85E0)); -#46352=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46353=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46354=AXIS2_PLACEMENT_3D('',#46351,#46352,#46353); -#46355=PLANE('',#46354); -#46356=ORIENTED_EDGE('',*,*,#46301,.T.); -#46358=ORIENTED_EDGE('',*,*,#46357,.F.); -#46359=ORIENTED_EDGE('',*,*,#24158,.F.); -#46360=ORIENTED_EDGE('',*,*,#44980,.F.); -#46361=EDGE_LOOP('',(#46356,#46358,#46359,#46360)); -#46362=FACE_OUTER_BOUND('',#46361,.F.); -#46364=CARTESIAN_POINT('',(6.9E0,3.E-1,7.85E0)); -#46365=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46366=DIRECTION('',(0.E0,0.E0,1.E0)); -#46367=AXIS2_PLACEMENT_3D('',#46364,#46365,#46366); -#46368=PLANE('',#46367); -#46369=ORIENTED_EDGE('',*,*,#46208,.F.); -#46370=ORIENTED_EDGE('',*,*,#46346,.T.); -#46371=ORIENTED_EDGE('',*,*,#22269,.T.); -#46373=ORIENTED_EDGE('',*,*,#46372,.F.); -#46374=EDGE_LOOP('',(#46369,#46370,#46371,#46373)); -#46375=FACE_OUTER_BOUND('',#46374,.F.); -#46377=CARTESIAN_POINT('',(6.9E0,3.E-1,7.85E0)); -#46378=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46379=DIRECTION('',(0.E0,0.E0,1.E0)); -#46380=AXIS2_PLACEMENT_3D('',#46377,#46378,#46379); -#46381=PLANE('',#46380); -#46382=ORIENTED_EDGE('',*,*,#46307,.T.); -#46384=ORIENTED_EDGE('',*,*,#46383,.F.); -#46385=ORIENTED_EDGE('',*,*,#24160,.F.); -#46386=ORIENTED_EDGE('',*,*,#46357,.T.); -#46387=EDGE_LOOP('',(#46382,#46384,#46385,#46386)); -#46388=FACE_OUTER_BOUND('',#46387,.F.); -#46390=CARTESIAN_POINT('',(6.9E0,3.E-1,8.55E0)); -#46391=DIRECTION('',(0.E0,0.E0,1.E0)); -#46392=DIRECTION('',(1.E0,0.E0,0.E0)); -#46393=AXIS2_PLACEMENT_3D('',#46390,#46391,#46392); -#46394=PLANE('',#46393); -#46395=ORIENTED_EDGE('',*,*,#46210,.F.); -#46396=ORIENTED_EDGE('',*,*,#46372,.T.); -#46397=ORIENTED_EDGE('',*,*,#22267,.F.); -#46398=ORIENTED_EDGE('',*,*,#45009,.T.); -#46399=EDGE_LOOP('',(#46395,#46396,#46397,#46398)); -#46400=FACE_OUTER_BOUND('',#46399,.F.); -#46402=CARTESIAN_POINT('',(6.9E0,3.E-1,8.55E0)); -#46403=DIRECTION('',(0.E0,0.E0,1.E0)); -#46404=DIRECTION('',(1.E0,0.E0,0.E0)); -#46405=AXIS2_PLACEMENT_3D('',#46402,#46403,#46404); -#46406=PLANE('',#46405); -#46407=ORIENTED_EDGE('',*,*,#46305,.T.); -#46408=ORIENTED_EDGE('',*,*,#45005,.T.); -#46409=ORIENTED_EDGE('',*,*,#24162,.T.); -#46410=ORIENTED_EDGE('',*,*,#46383,.T.); -#46411=EDGE_LOOP('',(#46407,#46408,#46409,#46410)); -#46412=FACE_OUTER_BOUND('',#46411,.F.); -#46414=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,8.2E0)); -#46415=DIRECTION('',(0.E0,1.E0,0.E0)); -#46416=DIRECTION('',(1.E0,0.E0,0.E0)); -#46417=AXIS2_PLACEMENT_3D('',#46414,#46415,#46416); -#46418=CYLINDRICAL_SURFACE('',#46417,4.E-1); -#46419=ORIENTED_EDGE('',*,*,#44992,.F.); -#46420=ORIENTED_EDGE('',*,*,#46212,.F.); -#46421=ORIENTED_EDGE('',*,*,#45007,.T.); -#46422=ORIENTED_EDGE('',*,*,#46303,.T.); -#46423=EDGE_LOOP('',(#46419,#46420,#46421,#46422)); -#46424=FACE_OUTER_BOUND('',#46423,.F.); -#46426=FILL_AREA_STYLE_COLOUR('',#15); -#46427=FILL_AREA_STYLE('',(#46426)); -#46428=SURFACE_STYLE_FILL_AREA(#46427); -#46429=SURFACE_SIDE_STYLE('',(#46428)); -#46430=SURFACE_STYLE_USAGE(.NEGATIVE.,#46429); -#46431=PRESENTATION_STYLE_ASSIGNMENT((#46430)); -#46432=STYLED_ITEM('',(#46431),#46425); -#46433=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.95E0)); -#46434=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46435=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46436=AXIS2_PLACEMENT_3D('',#46433,#46434,#46435); -#46437=PLANE('',#46436); -#46439=ORIENTED_EDGE('',*,*,#46438,.F.); -#46441=ORIENTED_EDGE('',*,*,#46440,.T.); -#46442=ORIENTED_EDGE('',*,*,#22199,.T.); -#46443=ORIENTED_EDGE('',*,*,#45292,.T.); -#46444=EDGE_LOOP('',(#46439,#46441,#46442,#46443)); -#46445=FACE_OUTER_BOUND('',#46444,.F.); -#46447=CARTESIAN_POINT('',(-5.9E0,3.E-1,8.95E0)); -#46448=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46449=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46450=AXIS2_PLACEMENT_3D('',#46447,#46448,#46449); -#46451=PLANE('',#46450); -#46453=ORIENTED_EDGE('',*,*,#46452,.T.); -#46454=ORIENTED_EDGE('',*,*,#45302,.T.); -#46455=ORIENTED_EDGE('',*,*,#24230,.F.); -#46457=ORIENTED_EDGE('',*,*,#46456,.T.); -#46458=EDGE_LOOP('',(#46453,#46454,#46455,#46457)); -#46459=FACE_OUTER_BOUND('',#46458,.F.); -#46461=CARTESIAN_POINT('',(0.E0,-2.5E-1,4.4E0)); -#46462=DIRECTION('',(0.E0,1.E0,0.E0)); -#46463=DIRECTION('',(1.E0,0.E0,0.E0)); -#46464=AXIS2_PLACEMENT_3D('',#46461,#46462,#46463); -#46465=PLANE('',#46464); -#46467=ORIENTED_EDGE('',*,*,#46466,.T.); -#46469=ORIENTED_EDGE('',*,*,#46468,.T.); -#46470=ORIENTED_EDGE('',*,*,#46438,.T.); -#46472=ORIENTED_EDGE('',*,*,#46471,.T.); -#46473=EDGE_LOOP('',(#46467,#46469,#46470,#46472)); -#46474=FACE_OUTER_BOUND('',#46473,.F.); -#46476=FILL_AREA_STYLE_COLOUR('',#15); -#46477=FILL_AREA_STYLE('',(#46476)); -#46478=SURFACE_STYLE_FILL_AREA(#46477); -#46479=SURFACE_SIDE_STYLE('',(#46478)); -#46480=SURFACE_STYLE_USAGE(.NEGATIVE.,#46479); -#46481=PRESENTATION_STYLE_ASSIGNMENT((#46480)); -#46482=STYLED_ITEM('',(#46481),#46475); -#46483=CARTESIAN_POINT('',(0.E0,-2.5E-1,4.4E0)); -#46484=DIRECTION('',(0.E0,1.E0,0.E0)); -#46485=DIRECTION('',(1.E0,0.E0,0.E0)); -#46486=AXIS2_PLACEMENT_3D('',#46483,#46484,#46485); -#46487=PLANE('',#46486); -#46489=ORIENTED_EDGE('',*,*,#46488,.T.); -#46491=ORIENTED_EDGE('',*,*,#46490,.T.); -#46493=ORIENTED_EDGE('',*,*,#46492,.T.); -#46495=ORIENTED_EDGE('',*,*,#46494,.T.); -#46496=EDGE_LOOP('',(#46489,#46491,#46493,#46495)); -#46497=FACE_OUTER_BOUND('',#46496,.F.); -#46499=FILL_AREA_STYLE_COLOUR('',#15); -#46500=FILL_AREA_STYLE('',(#46499)); -#46501=SURFACE_STYLE_FILL_AREA(#46500); -#46502=SURFACE_SIDE_STYLE('',(#46501)); -#46503=SURFACE_STYLE_USAGE(.NEGATIVE.,#46502); -#46504=PRESENTATION_STYLE_ASSIGNMENT((#46503)); -#46505=STYLED_ITEM('',(#46504),#46498); -#46506=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,9.65E0)); -#46507=DIRECTION('',(0.E0,0.E0,1.E0)); -#46508=DIRECTION('',(1.E0,0.E0,0.E0)); -#46509=AXIS2_PLACEMENT_3D('',#46506,#46507,#46508); -#46510=PLANE('',#46509); -#46511=ORIENTED_EDGE('',*,*,#46466,.F.); -#46512=ORIENTED_EDGE('',*,*,#45317,.F.); -#46513=ORIENTED_EDGE('',*,*,#22203,.T.); -#46515=ORIENTED_EDGE('',*,*,#46514,.F.); -#46516=EDGE_LOOP('',(#46511,#46512,#46513,#46515)); -#46517=FACE_OUTER_BOUND('',#46516,.F.); -#46519=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,9.65E0)); -#46520=DIRECTION('',(0.E0,0.E0,1.E0)); -#46521=DIRECTION('',(1.E0,0.E0,0.E0)); -#46522=AXIS2_PLACEMENT_3D('',#46519,#46520,#46521); -#46523=PLANE('',#46522); -#46525=ORIENTED_EDGE('',*,*,#46524,.T.); -#46527=ORIENTED_EDGE('',*,*,#46526,.F.); -#46528=ORIENTED_EDGE('',*,*,#24226,.F.); -#46529=ORIENTED_EDGE('',*,*,#45321,.F.); -#46530=EDGE_LOOP('',(#46525,#46527,#46528,#46529)); -#46531=FACE_OUTER_BOUND('',#46530,.F.); -#46533=CARTESIAN_POINT('',(-5.9E0,3.E-1,9.65E0)); -#46534=DIRECTION('',(1.E0,0.E0,0.E0)); -#46535=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46536=AXIS2_PLACEMENT_3D('',#46533,#46534,#46535); -#46537=PLANE('',#46536); -#46538=ORIENTED_EDGE('',*,*,#46468,.F.); -#46539=ORIENTED_EDGE('',*,*,#46514,.T.); -#46540=ORIENTED_EDGE('',*,*,#22201,.T.); -#46541=ORIENTED_EDGE('',*,*,#46440,.F.); -#46542=EDGE_LOOP('',(#46538,#46539,#46540,#46541)); -#46543=FACE_OUTER_BOUND('',#46542,.F.); -#46545=CARTESIAN_POINT('',(-5.9E0,3.E-1,9.65E0)); -#46546=DIRECTION('',(1.E0,0.E0,0.E0)); -#46547=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46548=AXIS2_PLACEMENT_3D('',#46545,#46546,#46547); -#46549=PLANE('',#46548); -#46551=ORIENTED_EDGE('',*,*,#46550,.T.); -#46552=ORIENTED_EDGE('',*,*,#46456,.F.); -#46553=ORIENTED_EDGE('',*,*,#24228,.F.); -#46554=ORIENTED_EDGE('',*,*,#46526,.T.); -#46555=EDGE_LOOP('',(#46551,#46552,#46553,#46554)); -#46556=FACE_OUTER_BOUND('',#46555,.F.); -#46558=CARTESIAN_POINT('',(0.E0,2.5E-1,4.4E0)); -#46559=DIRECTION('',(0.E0,1.E0,0.E0)); -#46560=DIRECTION('',(1.E0,0.E0,0.E0)); -#46561=AXIS2_PLACEMENT_3D('',#46558,#46559,#46560); -#46562=PLANE('',#46561); -#46563=ORIENTED_EDGE('',*,*,#46524,.F.); -#46565=ORIENTED_EDGE('',*,*,#46564,.F.); -#46566=ORIENTED_EDGE('',*,*,#46452,.F.); -#46567=ORIENTED_EDGE('',*,*,#46550,.F.); -#46568=EDGE_LOOP('',(#46563,#46565,#46566,#46567)); -#46569=FACE_OUTER_BOUND('',#46568,.F.); -#46571=FILL_AREA_STYLE_COLOUR('',#15); -#46572=FILL_AREA_STYLE('',(#46571)); -#46573=SURFACE_STYLE_FILL_AREA(#46572); -#46574=SURFACE_SIDE_STYLE('',(#46573)); -#46575=SURFACE_STYLE_USAGE(.POSITIVE.,#46574); -#46576=PRESENTATION_STYLE_ASSIGNMENT((#46575)); -#46577=STYLED_ITEM('',(#46576),#46570); -#46578=CARTESIAN_POINT('',(0.E0,2.5E-1,4.4E0)); -#46579=DIRECTION('',(0.E0,1.E0,0.E0)); -#46580=DIRECTION('',(1.E0,0.E0,0.E0)); -#46581=AXIS2_PLACEMENT_3D('',#46578,#46579,#46580); -#46582=PLANE('',#46581); -#46584=ORIENTED_EDGE('',*,*,#46583,.F.); -#46586=ORIENTED_EDGE('',*,*,#46585,.F.); -#46588=ORIENTED_EDGE('',*,*,#46587,.F.); -#46590=ORIENTED_EDGE('',*,*,#46589,.F.); -#46591=EDGE_LOOP('',(#46584,#46586,#46588,#46590)); -#46592=FACE_OUTER_BOUND('',#46591,.F.); -#46594=FILL_AREA_STYLE_COLOUR('',#15); -#46595=FILL_AREA_STYLE('',(#46594)); -#46596=SURFACE_STYLE_FILL_AREA(#46595); -#46597=SURFACE_SIDE_STYLE('',(#46596)); -#46598=SURFACE_STYLE_USAGE(.POSITIVE.,#46597); -#46599=PRESENTATION_STYLE_ASSIGNMENT((#46598)); -#46600=STYLED_ITEM('',(#46599),#46593); -#46601=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,9.3E0)); -#46602=DIRECTION('',(0.E0,1.E0,0.E0)); -#46603=DIRECTION('',(1.E0,0.E0,0.E0)); -#46604=AXIS2_PLACEMENT_3D('',#46601,#46602,#46603); -#46605=CYLINDRICAL_SURFACE('',#46604,4.E-1); -#46606=ORIENTED_EDGE('',*,*,#45304,.T.); -#46607=ORIENTED_EDGE('',*,*,#46564,.T.); -#46608=ORIENTED_EDGE('',*,*,#45319,.F.); -#46609=ORIENTED_EDGE('',*,*,#46471,.F.); -#46610=EDGE_LOOP('',(#46606,#46607,#46608,#46609)); -#46611=FACE_OUTER_BOUND('',#46610,.F.); -#46613=FILL_AREA_STYLE_COLOUR('',#15); -#46614=FILL_AREA_STYLE('',(#46613)); -#46615=SURFACE_STYLE_FILL_AREA(#46614); -#46616=SURFACE_SIDE_STYLE('',(#46615)); -#46617=SURFACE_STYLE_USAGE(.NEGATIVE.,#46616); -#46618=PRESENTATION_STYLE_ASSIGNMENT((#46617)); -#46619=STYLED_ITEM('',(#46618),#46612); -#46620=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,8.95E0)); -#46621=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46622=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46623=AXIS2_PLACEMENT_3D('',#46620,#46621,#46622); -#46624=PLANE('',#46623); -#46625=ORIENTED_EDGE('',*,*,#46488,.F.); -#46626=ORIENTED_EDGE('',*,*,#45012,.F.); -#46627=ORIENTED_EDGE('',*,*,#22263,.T.); -#46629=ORIENTED_EDGE('',*,*,#46628,.F.); -#46630=EDGE_LOOP('',(#46625,#46626,#46627,#46629)); -#46631=FACE_OUTER_BOUND('',#46630,.F.); -#46633=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,8.95E0)); -#46634=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46635=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46636=AXIS2_PLACEMENT_3D('',#46633,#46634,#46635); -#46637=PLANE('',#46636); -#46638=ORIENTED_EDGE('',*,*,#46583,.T.); -#46640=ORIENTED_EDGE('',*,*,#46639,.F.); -#46641=ORIENTED_EDGE('',*,*,#24166,.F.); -#46642=ORIENTED_EDGE('',*,*,#45002,.F.); -#46643=EDGE_LOOP('',(#46638,#46640,#46641,#46642)); -#46644=FACE_OUTER_BOUND('',#46643,.F.); -#46646=CARTESIAN_POINT('',(6.9E0,3.E-1,8.95E0)); -#46647=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46648=DIRECTION('',(0.E0,0.E0,1.E0)); -#46649=AXIS2_PLACEMENT_3D('',#46646,#46647,#46648); -#46650=PLANE('',#46649); -#46651=ORIENTED_EDGE('',*,*,#46490,.F.); -#46652=ORIENTED_EDGE('',*,*,#46628,.T.); -#46653=ORIENTED_EDGE('',*,*,#22261,.T.); -#46655=ORIENTED_EDGE('',*,*,#46654,.F.); -#46656=EDGE_LOOP('',(#46651,#46652,#46653,#46655)); -#46657=FACE_OUTER_BOUND('',#46656,.F.); -#46659=CARTESIAN_POINT('',(6.9E0,3.E-1,8.95E0)); -#46660=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46661=DIRECTION('',(0.E0,0.E0,1.E0)); -#46662=AXIS2_PLACEMENT_3D('',#46659,#46660,#46661); -#46663=PLANE('',#46662); -#46664=ORIENTED_EDGE('',*,*,#46589,.T.); -#46666=ORIENTED_EDGE('',*,*,#46665,.F.); -#46667=ORIENTED_EDGE('',*,*,#24168,.F.); -#46668=ORIENTED_EDGE('',*,*,#46639,.T.); -#46669=EDGE_LOOP('',(#46664,#46666,#46667,#46668)); -#46670=FACE_OUTER_BOUND('',#46669,.F.); -#46672=CARTESIAN_POINT('',(6.9E0,3.E-1,9.65E0)); -#46673=DIRECTION('',(0.E0,0.E0,1.E0)); -#46674=DIRECTION('',(1.E0,0.E0,0.E0)); -#46675=AXIS2_PLACEMENT_3D('',#46672,#46673,#46674); -#46676=PLANE('',#46675); -#46677=ORIENTED_EDGE('',*,*,#46492,.F.); -#46678=ORIENTED_EDGE('',*,*,#46654,.T.); -#46679=ORIENTED_EDGE('',*,*,#22259,.F.); -#46680=ORIENTED_EDGE('',*,*,#45031,.T.); -#46681=EDGE_LOOP('',(#46677,#46678,#46679,#46680)); -#46682=FACE_OUTER_BOUND('',#46681,.F.); -#46684=CARTESIAN_POINT('',(6.9E0,3.E-1,9.65E0)); -#46685=DIRECTION('',(0.E0,0.E0,1.E0)); -#46686=DIRECTION('',(1.E0,0.E0,0.E0)); -#46687=AXIS2_PLACEMENT_3D('',#46684,#46685,#46686); -#46688=PLANE('',#46687); -#46689=ORIENTED_EDGE('',*,*,#46587,.T.); -#46690=ORIENTED_EDGE('',*,*,#45027,.T.); -#46691=ORIENTED_EDGE('',*,*,#24170,.T.); -#46692=ORIENTED_EDGE('',*,*,#46665,.T.); -#46693=EDGE_LOOP('',(#46689,#46690,#46691,#46692)); -#46694=FACE_OUTER_BOUND('',#46693,.F.); -#46696=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,9.3E0)); -#46697=DIRECTION('',(0.E0,1.E0,0.E0)); -#46698=DIRECTION('',(1.E0,0.E0,0.E0)); -#46699=AXIS2_PLACEMENT_3D('',#46696,#46697,#46698); -#46700=CYLINDRICAL_SURFACE('',#46699,4.E-1); -#46701=ORIENTED_EDGE('',*,*,#45014,.F.); -#46702=ORIENTED_EDGE('',*,*,#46494,.F.); -#46703=ORIENTED_EDGE('',*,*,#45029,.T.); -#46704=ORIENTED_EDGE('',*,*,#46585,.T.); -#46705=EDGE_LOOP('',(#46701,#46702,#46703,#46704)); -#46706=FACE_OUTER_BOUND('',#46705,.F.); -#46708=FILL_AREA_STYLE_COLOUR('',#15); -#46709=FILL_AREA_STYLE('',(#46708)); -#46710=SURFACE_STYLE_FILL_AREA(#46709); -#46711=SURFACE_SIDE_STYLE('',(#46710)); -#46712=SURFACE_STYLE_USAGE(.NEGATIVE.,#46711); -#46713=PRESENTATION_STYLE_ASSIGNMENT((#46712)); -#46714=STYLED_ITEM('',(#46713),#46707); -#46715=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.005E1)); -#46716=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46717=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46718=AXIS2_PLACEMENT_3D('',#46715,#46716,#46717); -#46719=PLANE('',#46718); -#46721=ORIENTED_EDGE('',*,*,#46720,.F.); -#46723=ORIENTED_EDGE('',*,*,#46722,.T.); -#46724=ORIENTED_EDGE('',*,*,#22207,.T.); -#46725=ORIENTED_EDGE('',*,*,#45314,.T.); -#46726=EDGE_LOOP('',(#46721,#46723,#46724,#46725)); -#46727=FACE_OUTER_BOUND('',#46726,.F.); -#46729=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.005E1)); -#46730=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46731=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46732=AXIS2_PLACEMENT_3D('',#46729,#46730,#46731); -#46733=PLANE('',#46732); -#46735=ORIENTED_EDGE('',*,*,#46734,.T.); -#46736=ORIENTED_EDGE('',*,*,#45324,.T.); -#46737=ORIENTED_EDGE('',*,*,#24222,.F.); -#46739=ORIENTED_EDGE('',*,*,#46738,.T.); -#46740=EDGE_LOOP('',(#46735,#46736,#46737,#46739)); -#46741=FACE_OUTER_BOUND('',#46740,.F.); -#46743=CARTESIAN_POINT('',(0.E0,-2.5E-1,5.5E0)); -#46744=DIRECTION('',(0.E0,1.E0,0.E0)); -#46745=DIRECTION('',(1.E0,0.E0,0.E0)); -#46746=AXIS2_PLACEMENT_3D('',#46743,#46744,#46745); -#46747=PLANE('',#46746); -#46749=ORIENTED_EDGE('',*,*,#46748,.T.); -#46751=ORIENTED_EDGE('',*,*,#46750,.T.); -#46752=ORIENTED_EDGE('',*,*,#46720,.T.); -#46754=ORIENTED_EDGE('',*,*,#46753,.T.); -#46755=EDGE_LOOP('',(#46749,#46751,#46752,#46754)); -#46756=FACE_OUTER_BOUND('',#46755,.F.); -#46758=FILL_AREA_STYLE_COLOUR('',#15); -#46759=FILL_AREA_STYLE('',(#46758)); -#46760=SURFACE_STYLE_FILL_AREA(#46759); -#46761=SURFACE_SIDE_STYLE('',(#46760)); -#46762=SURFACE_STYLE_USAGE(.NEGATIVE.,#46761); -#46763=PRESENTATION_STYLE_ASSIGNMENT((#46762)); -#46764=STYLED_ITEM('',(#46763),#46757); -#46765=CARTESIAN_POINT('',(0.E0,-2.5E-1,5.5E0)); -#46766=DIRECTION('',(0.E0,1.E0,0.E0)); -#46767=DIRECTION('',(1.E0,0.E0,0.E0)); -#46768=AXIS2_PLACEMENT_3D('',#46765,#46766,#46767); -#46769=PLANE('',#46768); -#46771=ORIENTED_EDGE('',*,*,#46770,.T.); -#46773=ORIENTED_EDGE('',*,*,#46772,.T.); -#46775=ORIENTED_EDGE('',*,*,#46774,.T.); -#46777=ORIENTED_EDGE('',*,*,#46776,.T.); -#46778=EDGE_LOOP('',(#46771,#46773,#46775,#46777)); -#46779=FACE_OUTER_BOUND('',#46778,.F.); -#46781=FILL_AREA_STYLE_COLOUR('',#15); -#46782=FILL_AREA_STYLE('',(#46781)); -#46783=SURFACE_STYLE_FILL_AREA(#46782); -#46784=SURFACE_SIDE_STYLE('',(#46783)); -#46785=SURFACE_STYLE_USAGE(.NEGATIVE.,#46784); -#46786=PRESENTATION_STYLE_ASSIGNMENT((#46785)); -#46787=STYLED_ITEM('',(#46786),#46780); -#46788=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.075E1)); -#46789=DIRECTION('',(0.E0,0.E0,1.E0)); -#46790=DIRECTION('',(1.E0,0.E0,0.E0)); -#46791=AXIS2_PLACEMENT_3D('',#46788,#46789,#46790); -#46792=PLANE('',#46791); -#46793=ORIENTED_EDGE('',*,*,#46748,.F.); -#46794=ORIENTED_EDGE('',*,*,#45339,.F.); -#46795=ORIENTED_EDGE('',*,*,#22211,.T.); -#46797=ORIENTED_EDGE('',*,*,#46796,.F.); -#46798=EDGE_LOOP('',(#46793,#46794,#46795,#46797)); -#46799=FACE_OUTER_BOUND('',#46798,.F.); -#46801=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.075E1)); -#46802=DIRECTION('',(0.E0,0.E0,1.E0)); -#46803=DIRECTION('',(1.E0,0.E0,0.E0)); -#46804=AXIS2_PLACEMENT_3D('',#46801,#46802,#46803); -#46805=PLANE('',#46804); -#46807=ORIENTED_EDGE('',*,*,#46806,.T.); -#46809=ORIENTED_EDGE('',*,*,#46808,.F.); -#46810=ORIENTED_EDGE('',*,*,#24218,.F.); -#46811=ORIENTED_EDGE('',*,*,#45343,.F.); -#46812=EDGE_LOOP('',(#46807,#46809,#46810,#46811)); -#46813=FACE_OUTER_BOUND('',#46812,.F.); -#46815=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.075E1)); -#46816=DIRECTION('',(1.E0,0.E0,0.E0)); -#46817=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46818=AXIS2_PLACEMENT_3D('',#46815,#46816,#46817); -#46819=PLANE('',#46818); -#46820=ORIENTED_EDGE('',*,*,#46750,.F.); -#46821=ORIENTED_EDGE('',*,*,#46796,.T.); -#46822=ORIENTED_EDGE('',*,*,#22209,.T.); -#46823=ORIENTED_EDGE('',*,*,#46722,.F.); -#46824=EDGE_LOOP('',(#46820,#46821,#46822,#46823)); -#46825=FACE_OUTER_BOUND('',#46824,.F.); -#46827=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.075E1)); -#46828=DIRECTION('',(1.E0,0.E0,0.E0)); -#46829=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46830=AXIS2_PLACEMENT_3D('',#46827,#46828,#46829); -#46831=PLANE('',#46830); -#46833=ORIENTED_EDGE('',*,*,#46832,.T.); -#46834=ORIENTED_EDGE('',*,*,#46738,.F.); -#46835=ORIENTED_EDGE('',*,*,#24220,.F.); -#46836=ORIENTED_EDGE('',*,*,#46808,.T.); -#46837=EDGE_LOOP('',(#46833,#46834,#46835,#46836)); -#46838=FACE_OUTER_BOUND('',#46837,.F.); -#46840=CARTESIAN_POINT('',(0.E0,2.5E-1,5.5E0)); -#46841=DIRECTION('',(0.E0,1.E0,0.E0)); -#46842=DIRECTION('',(1.E0,0.E0,0.E0)); -#46843=AXIS2_PLACEMENT_3D('',#46840,#46841,#46842); -#46844=PLANE('',#46843); -#46845=ORIENTED_EDGE('',*,*,#46806,.F.); -#46847=ORIENTED_EDGE('',*,*,#46846,.F.); -#46848=ORIENTED_EDGE('',*,*,#46734,.F.); -#46849=ORIENTED_EDGE('',*,*,#46832,.F.); -#46850=EDGE_LOOP('',(#46845,#46847,#46848,#46849)); -#46851=FACE_OUTER_BOUND('',#46850,.F.); -#46853=FILL_AREA_STYLE_COLOUR('',#15); -#46854=FILL_AREA_STYLE('',(#46853)); -#46855=SURFACE_STYLE_FILL_AREA(#46854); -#46856=SURFACE_SIDE_STYLE('',(#46855)); -#46857=SURFACE_STYLE_USAGE(.POSITIVE.,#46856); -#46858=PRESENTATION_STYLE_ASSIGNMENT((#46857)); -#46859=STYLED_ITEM('',(#46858),#46852); -#46860=CARTESIAN_POINT('',(0.E0,2.5E-1,5.5E0)); -#46861=DIRECTION('',(0.E0,1.E0,0.E0)); -#46862=DIRECTION('',(1.E0,0.E0,0.E0)); -#46863=AXIS2_PLACEMENT_3D('',#46860,#46861,#46862); -#46864=PLANE('',#46863); -#46866=ORIENTED_EDGE('',*,*,#46865,.F.); -#46868=ORIENTED_EDGE('',*,*,#46867,.F.); -#46870=ORIENTED_EDGE('',*,*,#46869,.F.); -#46872=ORIENTED_EDGE('',*,*,#46871,.F.); -#46873=EDGE_LOOP('',(#46866,#46868,#46870,#46872)); -#46874=FACE_OUTER_BOUND('',#46873,.F.); -#46876=FILL_AREA_STYLE_COLOUR('',#15); -#46877=FILL_AREA_STYLE('',(#46876)); -#46878=SURFACE_STYLE_FILL_AREA(#46877); -#46879=SURFACE_SIDE_STYLE('',(#46878)); -#46880=SURFACE_STYLE_USAGE(.POSITIVE.,#46879); -#46881=PRESENTATION_STYLE_ASSIGNMENT((#46880)); -#46882=STYLED_ITEM('',(#46881),#46875); -#46883=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.04E1)); -#46884=DIRECTION('',(0.E0,1.E0,0.E0)); -#46885=DIRECTION('',(1.E0,0.E0,0.E0)); -#46886=AXIS2_PLACEMENT_3D('',#46883,#46884,#46885); -#46887=CYLINDRICAL_SURFACE('',#46886,4.E-1); -#46888=ORIENTED_EDGE('',*,*,#45326,.T.); -#46889=ORIENTED_EDGE('',*,*,#46846,.T.); -#46890=ORIENTED_EDGE('',*,*,#45341,.F.); -#46891=ORIENTED_EDGE('',*,*,#46753,.F.); -#46892=EDGE_LOOP('',(#46888,#46889,#46890,#46891)); -#46893=FACE_OUTER_BOUND('',#46892,.F.); -#46895=FILL_AREA_STYLE_COLOUR('',#15); -#46896=FILL_AREA_STYLE('',(#46895)); -#46897=SURFACE_STYLE_FILL_AREA(#46896); -#46898=SURFACE_SIDE_STYLE('',(#46897)); -#46899=SURFACE_STYLE_USAGE(.NEGATIVE.,#46898); -#46900=PRESENTATION_STYLE_ASSIGNMENT((#46899)); -#46901=STYLED_ITEM('',(#46900),#46894); -#46902=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.005E1)); -#46903=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46904=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46905=AXIS2_PLACEMENT_3D('',#46902,#46903,#46904); -#46906=PLANE('',#46905); -#46907=ORIENTED_EDGE('',*,*,#46770,.F.); -#46908=ORIENTED_EDGE('',*,*,#45034,.F.); -#46909=ORIENTED_EDGE('',*,*,#22255,.T.); -#46911=ORIENTED_EDGE('',*,*,#46910,.F.); -#46912=EDGE_LOOP('',(#46907,#46908,#46909,#46911)); -#46913=FACE_OUTER_BOUND('',#46912,.F.); -#46915=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.005E1)); -#46916=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46917=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46918=AXIS2_PLACEMENT_3D('',#46915,#46916,#46917); -#46919=PLANE('',#46918); -#46920=ORIENTED_EDGE('',*,*,#46865,.T.); -#46922=ORIENTED_EDGE('',*,*,#46921,.F.); -#46923=ORIENTED_EDGE('',*,*,#24174,.F.); -#46924=ORIENTED_EDGE('',*,*,#45024,.F.); -#46925=EDGE_LOOP('',(#46920,#46922,#46923,#46924)); -#46926=FACE_OUTER_BOUND('',#46925,.F.); -#46928=CARTESIAN_POINT('',(6.9E0,3.E-1,1.005E1)); -#46929=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46930=DIRECTION('',(0.E0,0.E0,1.E0)); -#46931=AXIS2_PLACEMENT_3D('',#46928,#46929,#46930); -#46932=PLANE('',#46931); -#46933=ORIENTED_EDGE('',*,*,#46772,.F.); -#46934=ORIENTED_EDGE('',*,*,#46910,.T.); -#46935=ORIENTED_EDGE('',*,*,#22253,.T.); -#46937=ORIENTED_EDGE('',*,*,#46936,.F.); -#46938=EDGE_LOOP('',(#46933,#46934,#46935,#46937)); -#46939=FACE_OUTER_BOUND('',#46938,.F.); -#46941=CARTESIAN_POINT('',(6.9E0,3.E-1,1.005E1)); -#46942=DIRECTION('',(-1.E0,0.E0,0.E0)); -#46943=DIRECTION('',(0.E0,0.E0,1.E0)); -#46944=AXIS2_PLACEMENT_3D('',#46941,#46942,#46943); -#46945=PLANE('',#46944); -#46946=ORIENTED_EDGE('',*,*,#46871,.T.); -#46948=ORIENTED_EDGE('',*,*,#46947,.F.); -#46949=ORIENTED_EDGE('',*,*,#24176,.F.); -#46950=ORIENTED_EDGE('',*,*,#46921,.T.); -#46951=EDGE_LOOP('',(#46946,#46948,#46949,#46950)); -#46952=FACE_OUTER_BOUND('',#46951,.F.); -#46954=CARTESIAN_POINT('',(6.9E0,3.E-1,1.075E1)); -#46955=DIRECTION('',(0.E0,0.E0,1.E0)); -#46956=DIRECTION('',(1.E0,0.E0,0.E0)); -#46957=AXIS2_PLACEMENT_3D('',#46954,#46955,#46956); -#46958=PLANE('',#46957); -#46959=ORIENTED_EDGE('',*,*,#46774,.F.); -#46960=ORIENTED_EDGE('',*,*,#46936,.T.); -#46961=ORIENTED_EDGE('',*,*,#22251,.F.); -#46962=ORIENTED_EDGE('',*,*,#45053,.T.); -#46963=EDGE_LOOP('',(#46959,#46960,#46961,#46962)); -#46964=FACE_OUTER_BOUND('',#46963,.F.); -#46966=CARTESIAN_POINT('',(6.9E0,3.E-1,1.075E1)); -#46967=DIRECTION('',(0.E0,0.E0,1.E0)); -#46968=DIRECTION('',(1.E0,0.E0,0.E0)); -#46969=AXIS2_PLACEMENT_3D('',#46966,#46967,#46968); -#46970=PLANE('',#46969); -#46971=ORIENTED_EDGE('',*,*,#46869,.T.); -#46972=ORIENTED_EDGE('',*,*,#45049,.T.); -#46973=ORIENTED_EDGE('',*,*,#24178,.T.); -#46974=ORIENTED_EDGE('',*,*,#46947,.T.); -#46975=EDGE_LOOP('',(#46971,#46972,#46973,#46974)); -#46976=FACE_OUTER_BOUND('',#46975,.F.); -#46978=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.04E1)); -#46979=DIRECTION('',(0.E0,1.E0,0.E0)); -#46980=DIRECTION('',(1.E0,0.E0,0.E0)); -#46981=AXIS2_PLACEMENT_3D('',#46978,#46979,#46980); -#46982=CYLINDRICAL_SURFACE('',#46981,4.E-1); -#46983=ORIENTED_EDGE('',*,*,#45036,.F.); -#46984=ORIENTED_EDGE('',*,*,#46776,.F.); -#46985=ORIENTED_EDGE('',*,*,#45051,.T.); -#46986=ORIENTED_EDGE('',*,*,#46867,.T.); -#46987=EDGE_LOOP('',(#46983,#46984,#46985,#46986)); -#46988=FACE_OUTER_BOUND('',#46987,.F.); -#46990=FILL_AREA_STYLE_COLOUR('',#15); -#46991=FILL_AREA_STYLE('',(#46990)); -#46992=SURFACE_STYLE_FILL_AREA(#46991); -#46993=SURFACE_SIDE_STYLE('',(#46992)); -#46994=SURFACE_STYLE_USAGE(.NEGATIVE.,#46993); -#46995=PRESENTATION_STYLE_ASSIGNMENT((#46994)); -#46996=STYLED_ITEM('',(#46995),#46989); -#46997=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.115E1)); -#46998=DIRECTION('',(0.E0,0.E0,-1.E0)); -#46999=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47000=AXIS2_PLACEMENT_3D('',#46997,#46998,#46999); -#47001=PLANE('',#47000); -#47003=ORIENTED_EDGE('',*,*,#47002,.F.); -#47005=ORIENTED_EDGE('',*,*,#47004,.T.); -#47006=ORIENTED_EDGE('',*,*,#22215,.T.); -#47007=ORIENTED_EDGE('',*,*,#45336,.T.); -#47008=EDGE_LOOP('',(#47003,#47005,#47006,#47007)); -#47009=FACE_OUTER_BOUND('',#47008,.F.); -#47011=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.115E1)); -#47012=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47013=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47014=AXIS2_PLACEMENT_3D('',#47011,#47012,#47013); -#47015=PLANE('',#47014); -#47017=ORIENTED_EDGE('',*,*,#47016,.T.); -#47018=ORIENTED_EDGE('',*,*,#45346,.T.); -#47019=ORIENTED_EDGE('',*,*,#24214,.F.); -#47021=ORIENTED_EDGE('',*,*,#47020,.T.); -#47022=EDGE_LOOP('',(#47017,#47018,#47019,#47021)); -#47023=FACE_OUTER_BOUND('',#47022,.F.); -#47025=CARTESIAN_POINT('',(0.E0,-2.5E-1,6.6E0)); -#47026=DIRECTION('',(0.E0,1.E0,0.E0)); -#47027=DIRECTION('',(1.E0,0.E0,0.E0)); -#47028=AXIS2_PLACEMENT_3D('',#47025,#47026,#47027); -#47029=PLANE('',#47028); -#47031=ORIENTED_EDGE('',*,*,#47030,.T.); -#47033=ORIENTED_EDGE('',*,*,#47032,.T.); -#47034=ORIENTED_EDGE('',*,*,#47002,.T.); -#47036=ORIENTED_EDGE('',*,*,#47035,.T.); -#47037=EDGE_LOOP('',(#47031,#47033,#47034,#47036)); -#47038=FACE_OUTER_BOUND('',#47037,.F.); -#47040=FILL_AREA_STYLE_COLOUR('',#15); -#47041=FILL_AREA_STYLE('',(#47040)); -#47042=SURFACE_STYLE_FILL_AREA(#47041); -#47043=SURFACE_SIDE_STYLE('',(#47042)); -#47044=SURFACE_STYLE_USAGE(.NEGATIVE.,#47043); -#47045=PRESENTATION_STYLE_ASSIGNMENT((#47044)); -#47046=STYLED_ITEM('',(#47045),#47039); -#47047=CARTESIAN_POINT('',(0.E0,-2.5E-1,6.6E0)); -#47048=DIRECTION('',(0.E0,1.E0,0.E0)); -#47049=DIRECTION('',(1.E0,0.E0,0.E0)); -#47050=AXIS2_PLACEMENT_3D('',#47047,#47048,#47049); -#47051=PLANE('',#47050); -#47053=ORIENTED_EDGE('',*,*,#47052,.T.); -#47055=ORIENTED_EDGE('',*,*,#47054,.T.); -#47057=ORIENTED_EDGE('',*,*,#47056,.T.); -#47059=ORIENTED_EDGE('',*,*,#47058,.T.); -#47060=EDGE_LOOP('',(#47053,#47055,#47057,#47059)); -#47061=FACE_OUTER_BOUND('',#47060,.F.); -#47063=FILL_AREA_STYLE_COLOUR('',#15); -#47064=FILL_AREA_STYLE('',(#47063)); -#47065=SURFACE_STYLE_FILL_AREA(#47064); -#47066=SURFACE_SIDE_STYLE('',(#47065)); -#47067=SURFACE_STYLE_USAGE(.NEGATIVE.,#47066); -#47068=PRESENTATION_STYLE_ASSIGNMENT((#47067)); -#47069=STYLED_ITEM('',(#47068),#47062); -#47070=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.185E1)); -#47071=DIRECTION('',(0.E0,0.E0,1.E0)); -#47072=DIRECTION('',(1.E0,0.E0,0.E0)); -#47073=AXIS2_PLACEMENT_3D('',#47070,#47071,#47072); -#47074=PLANE('',#47073); -#47075=ORIENTED_EDGE('',*,*,#47030,.F.); -#47076=ORIENTED_EDGE('',*,*,#45361,.F.); -#47077=ORIENTED_EDGE('',*,*,#22219,.T.); -#47079=ORIENTED_EDGE('',*,*,#47078,.F.); -#47080=EDGE_LOOP('',(#47075,#47076,#47077,#47079)); -#47081=FACE_OUTER_BOUND('',#47080,.F.); -#47083=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.185E1)); -#47084=DIRECTION('',(0.E0,0.E0,1.E0)); -#47085=DIRECTION('',(1.E0,0.E0,0.E0)); -#47086=AXIS2_PLACEMENT_3D('',#47083,#47084,#47085); -#47087=PLANE('',#47086); -#47089=ORIENTED_EDGE('',*,*,#47088,.T.); -#47091=ORIENTED_EDGE('',*,*,#47090,.F.); -#47092=ORIENTED_EDGE('',*,*,#24210,.F.); -#47093=ORIENTED_EDGE('',*,*,#45365,.F.); -#47094=EDGE_LOOP('',(#47089,#47091,#47092,#47093)); -#47095=FACE_OUTER_BOUND('',#47094,.F.); -#47097=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.185E1)); -#47098=DIRECTION('',(1.E0,0.E0,0.E0)); -#47099=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47100=AXIS2_PLACEMENT_3D('',#47097,#47098,#47099); -#47101=PLANE('',#47100); -#47102=ORIENTED_EDGE('',*,*,#47032,.F.); -#47103=ORIENTED_EDGE('',*,*,#47078,.T.); -#47104=ORIENTED_EDGE('',*,*,#22217,.T.); -#47105=ORIENTED_EDGE('',*,*,#47004,.F.); -#47106=EDGE_LOOP('',(#47102,#47103,#47104,#47105)); -#47107=FACE_OUTER_BOUND('',#47106,.F.); -#47109=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.185E1)); -#47110=DIRECTION('',(1.E0,0.E0,0.E0)); -#47111=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47112=AXIS2_PLACEMENT_3D('',#47109,#47110,#47111); -#47113=PLANE('',#47112); -#47115=ORIENTED_EDGE('',*,*,#47114,.T.); -#47116=ORIENTED_EDGE('',*,*,#47020,.F.); -#47117=ORIENTED_EDGE('',*,*,#24212,.F.); -#47118=ORIENTED_EDGE('',*,*,#47090,.T.); -#47119=EDGE_LOOP('',(#47115,#47116,#47117,#47118)); -#47120=FACE_OUTER_BOUND('',#47119,.F.); -#47122=CARTESIAN_POINT('',(0.E0,2.5E-1,6.6E0)); -#47123=DIRECTION('',(0.E0,1.E0,0.E0)); -#47124=DIRECTION('',(1.E0,0.E0,0.E0)); -#47125=AXIS2_PLACEMENT_3D('',#47122,#47123,#47124); -#47126=PLANE('',#47125); -#47127=ORIENTED_EDGE('',*,*,#47088,.F.); -#47129=ORIENTED_EDGE('',*,*,#47128,.F.); -#47130=ORIENTED_EDGE('',*,*,#47016,.F.); -#47131=ORIENTED_EDGE('',*,*,#47114,.F.); -#47132=EDGE_LOOP('',(#47127,#47129,#47130,#47131)); -#47133=FACE_OUTER_BOUND('',#47132,.F.); -#47135=FILL_AREA_STYLE_COLOUR('',#15); -#47136=FILL_AREA_STYLE('',(#47135)); -#47137=SURFACE_STYLE_FILL_AREA(#47136); -#47138=SURFACE_SIDE_STYLE('',(#47137)); -#47139=SURFACE_STYLE_USAGE(.POSITIVE.,#47138); -#47140=PRESENTATION_STYLE_ASSIGNMENT((#47139)); -#47141=STYLED_ITEM('',(#47140),#47134); -#47142=CARTESIAN_POINT('',(0.E0,2.5E-1,6.6E0)); -#47143=DIRECTION('',(0.E0,1.E0,0.E0)); -#47144=DIRECTION('',(1.E0,0.E0,0.E0)); -#47145=AXIS2_PLACEMENT_3D('',#47142,#47143,#47144); -#47146=PLANE('',#47145); -#47148=ORIENTED_EDGE('',*,*,#47147,.F.); -#47150=ORIENTED_EDGE('',*,*,#47149,.F.); -#47152=ORIENTED_EDGE('',*,*,#47151,.F.); -#47154=ORIENTED_EDGE('',*,*,#47153,.F.); -#47155=EDGE_LOOP('',(#47148,#47150,#47152,#47154)); -#47156=FACE_OUTER_BOUND('',#47155,.F.); -#47158=FILL_AREA_STYLE_COLOUR('',#15); -#47159=FILL_AREA_STYLE('',(#47158)); -#47160=SURFACE_STYLE_FILL_AREA(#47159); -#47161=SURFACE_SIDE_STYLE('',(#47160)); -#47162=SURFACE_STYLE_USAGE(.POSITIVE.,#47161); -#47163=PRESENTATION_STYLE_ASSIGNMENT((#47162)); -#47164=STYLED_ITEM('',(#47163),#47157); -#47165=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.15E1)); -#47166=DIRECTION('',(0.E0,1.E0,0.E0)); -#47167=DIRECTION('',(1.E0,0.E0,0.E0)); -#47168=AXIS2_PLACEMENT_3D('',#47165,#47166,#47167); -#47169=CYLINDRICAL_SURFACE('',#47168,4.E-1); -#47170=ORIENTED_EDGE('',*,*,#45348,.T.); -#47171=ORIENTED_EDGE('',*,*,#47128,.T.); -#47172=ORIENTED_EDGE('',*,*,#45363,.F.); -#47173=ORIENTED_EDGE('',*,*,#47035,.F.); -#47174=EDGE_LOOP('',(#47170,#47171,#47172,#47173)); -#47175=FACE_OUTER_BOUND('',#47174,.F.); -#47177=FILL_AREA_STYLE_COLOUR('',#15); -#47178=FILL_AREA_STYLE('',(#47177)); -#47179=SURFACE_STYLE_FILL_AREA(#47178); -#47180=SURFACE_SIDE_STYLE('',(#47179)); -#47181=SURFACE_STYLE_USAGE(.NEGATIVE.,#47180); -#47182=PRESENTATION_STYLE_ASSIGNMENT((#47181)); -#47183=STYLED_ITEM('',(#47182),#47176); -#47184=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.115E1)); -#47185=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47186=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47187=AXIS2_PLACEMENT_3D('',#47184,#47185,#47186); -#47188=PLANE('',#47187); -#47189=ORIENTED_EDGE('',*,*,#47052,.F.); -#47190=ORIENTED_EDGE('',*,*,#45056,.F.); -#47191=ORIENTED_EDGE('',*,*,#22247,.T.); -#47193=ORIENTED_EDGE('',*,*,#47192,.F.); -#47194=EDGE_LOOP('',(#47189,#47190,#47191,#47193)); -#47195=FACE_OUTER_BOUND('',#47194,.F.); -#47197=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.115E1)); -#47198=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47199=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47200=AXIS2_PLACEMENT_3D('',#47197,#47198,#47199); -#47201=PLANE('',#47200); -#47202=ORIENTED_EDGE('',*,*,#47147,.T.); -#47204=ORIENTED_EDGE('',*,*,#47203,.F.); -#47205=ORIENTED_EDGE('',*,*,#24182,.F.); -#47206=ORIENTED_EDGE('',*,*,#45046,.F.); -#47207=EDGE_LOOP('',(#47202,#47204,#47205,#47206)); -#47208=FACE_OUTER_BOUND('',#47207,.F.); -#47210=CARTESIAN_POINT('',(6.9E0,3.E-1,1.115E1)); -#47211=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47212=DIRECTION('',(0.E0,0.E0,1.E0)); -#47213=AXIS2_PLACEMENT_3D('',#47210,#47211,#47212); -#47214=PLANE('',#47213); -#47215=ORIENTED_EDGE('',*,*,#47054,.F.); -#47216=ORIENTED_EDGE('',*,*,#47192,.T.); -#47217=ORIENTED_EDGE('',*,*,#22245,.T.); -#47219=ORIENTED_EDGE('',*,*,#47218,.F.); -#47220=EDGE_LOOP('',(#47215,#47216,#47217,#47219)); -#47221=FACE_OUTER_BOUND('',#47220,.F.); -#47223=CARTESIAN_POINT('',(6.9E0,3.E-1,1.115E1)); -#47224=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47225=DIRECTION('',(0.E0,0.E0,1.E0)); -#47226=AXIS2_PLACEMENT_3D('',#47223,#47224,#47225); -#47227=PLANE('',#47226); -#47228=ORIENTED_EDGE('',*,*,#47153,.T.); -#47230=ORIENTED_EDGE('',*,*,#47229,.F.); -#47231=ORIENTED_EDGE('',*,*,#24184,.F.); -#47232=ORIENTED_EDGE('',*,*,#47203,.T.); -#47233=EDGE_LOOP('',(#47228,#47230,#47231,#47232)); -#47234=FACE_OUTER_BOUND('',#47233,.F.); -#47236=CARTESIAN_POINT('',(6.9E0,3.E-1,1.185E1)); -#47237=DIRECTION('',(0.E0,0.E0,1.E0)); -#47238=DIRECTION('',(1.E0,0.E0,0.E0)); -#47239=AXIS2_PLACEMENT_3D('',#47236,#47237,#47238); -#47240=PLANE('',#47239); -#47241=ORIENTED_EDGE('',*,*,#47056,.F.); -#47242=ORIENTED_EDGE('',*,*,#47218,.T.); -#47243=ORIENTED_EDGE('',*,*,#22243,.F.); -#47244=ORIENTED_EDGE('',*,*,#45075,.T.); -#47245=EDGE_LOOP('',(#47241,#47242,#47243,#47244)); -#47246=FACE_OUTER_BOUND('',#47245,.F.); -#47248=CARTESIAN_POINT('',(6.9E0,3.E-1,1.185E1)); -#47249=DIRECTION('',(0.E0,0.E0,1.E0)); -#47250=DIRECTION('',(1.E0,0.E0,0.E0)); -#47251=AXIS2_PLACEMENT_3D('',#47248,#47249,#47250); -#47252=PLANE('',#47251); -#47253=ORIENTED_EDGE('',*,*,#47151,.T.); -#47254=ORIENTED_EDGE('',*,*,#45071,.T.); -#47255=ORIENTED_EDGE('',*,*,#24186,.T.); -#47256=ORIENTED_EDGE('',*,*,#47229,.T.); -#47257=EDGE_LOOP('',(#47253,#47254,#47255,#47256)); -#47258=FACE_OUTER_BOUND('',#47257,.F.); -#47260=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.15E1)); -#47261=DIRECTION('',(0.E0,1.E0,0.E0)); -#47262=DIRECTION('',(1.E0,0.E0,0.E0)); -#47263=AXIS2_PLACEMENT_3D('',#47260,#47261,#47262); -#47264=CYLINDRICAL_SURFACE('',#47263,4.E-1); -#47265=ORIENTED_EDGE('',*,*,#45058,.F.); -#47266=ORIENTED_EDGE('',*,*,#47058,.F.); -#47267=ORIENTED_EDGE('',*,*,#45073,.T.); -#47268=ORIENTED_EDGE('',*,*,#47149,.T.); -#47269=EDGE_LOOP('',(#47265,#47266,#47267,#47268)); -#47270=FACE_OUTER_BOUND('',#47269,.F.); -#47272=FILL_AREA_STYLE_COLOUR('',#15); -#47273=FILL_AREA_STYLE('',(#47272)); -#47274=SURFACE_STYLE_FILL_AREA(#47273); -#47275=SURFACE_SIDE_STYLE('',(#47274)); -#47276=SURFACE_STYLE_USAGE(.NEGATIVE.,#47275); -#47277=PRESENTATION_STYLE_ASSIGNMENT((#47276)); -#47278=STYLED_ITEM('',(#47277),#47271); -#47279=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.225E1)); -#47280=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47281=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47282=AXIS2_PLACEMENT_3D('',#47279,#47280,#47281); -#47283=PLANE('',#47282); -#47285=ORIENTED_EDGE('',*,*,#47284,.F.); -#47287=ORIENTED_EDGE('',*,*,#47286,.T.); -#47288=ORIENTED_EDGE('',*,*,#22223,.T.); -#47289=ORIENTED_EDGE('',*,*,#45358,.T.); -#47290=EDGE_LOOP('',(#47285,#47287,#47288,#47289)); -#47291=FACE_OUTER_BOUND('',#47290,.F.); -#47293=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.225E1)); -#47294=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47295=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47296=AXIS2_PLACEMENT_3D('',#47293,#47294,#47295); -#47297=PLANE('',#47296); -#47299=ORIENTED_EDGE('',*,*,#47298,.T.); -#47300=ORIENTED_EDGE('',*,*,#45368,.T.); -#47301=ORIENTED_EDGE('',*,*,#24206,.F.); -#47303=ORIENTED_EDGE('',*,*,#47302,.T.); -#47304=EDGE_LOOP('',(#47299,#47300,#47301,#47303)); -#47305=FACE_OUTER_BOUND('',#47304,.F.); -#47307=CARTESIAN_POINT('',(0.E0,-2.5E-1,7.7E0)); -#47308=DIRECTION('',(0.E0,1.E0,0.E0)); -#47309=DIRECTION('',(1.E0,0.E0,0.E0)); -#47310=AXIS2_PLACEMENT_3D('',#47307,#47308,#47309); -#47311=PLANE('',#47310); -#47313=ORIENTED_EDGE('',*,*,#47312,.T.); -#47315=ORIENTED_EDGE('',*,*,#47314,.T.); -#47316=ORIENTED_EDGE('',*,*,#47284,.T.); -#47318=ORIENTED_EDGE('',*,*,#47317,.T.); -#47319=EDGE_LOOP('',(#47313,#47315,#47316,#47318)); -#47320=FACE_OUTER_BOUND('',#47319,.F.); -#47322=FILL_AREA_STYLE_COLOUR('',#15); -#47323=FILL_AREA_STYLE('',(#47322)); -#47324=SURFACE_STYLE_FILL_AREA(#47323); -#47325=SURFACE_SIDE_STYLE('',(#47324)); -#47326=SURFACE_STYLE_USAGE(.NEGATIVE.,#47325); -#47327=PRESENTATION_STYLE_ASSIGNMENT((#47326)); -#47328=STYLED_ITEM('',(#47327),#47321); -#47329=CARTESIAN_POINT('',(0.E0,-2.5E-1,7.7E0)); -#47330=DIRECTION('',(0.E0,1.E0,0.E0)); -#47331=DIRECTION('',(1.E0,0.E0,0.E0)); -#47332=AXIS2_PLACEMENT_3D('',#47329,#47330,#47331); -#47333=PLANE('',#47332); -#47335=ORIENTED_EDGE('',*,*,#47334,.T.); -#47337=ORIENTED_EDGE('',*,*,#47336,.T.); -#47339=ORIENTED_EDGE('',*,*,#47338,.T.); -#47341=ORIENTED_EDGE('',*,*,#47340,.T.); -#47342=EDGE_LOOP('',(#47335,#47337,#47339,#47341)); -#47343=FACE_OUTER_BOUND('',#47342,.F.); -#47345=FILL_AREA_STYLE_COLOUR('',#15); -#47346=FILL_AREA_STYLE('',(#47345)); -#47347=SURFACE_STYLE_FILL_AREA(#47346); -#47348=SURFACE_SIDE_STYLE('',(#47347)); -#47349=SURFACE_STYLE_USAGE(.NEGATIVE.,#47348); -#47350=PRESENTATION_STYLE_ASSIGNMENT((#47349)); -#47351=STYLED_ITEM('',(#47350),#47344); -#47352=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.295E1)); -#47353=DIRECTION('',(0.E0,0.E0,1.E0)); -#47354=DIRECTION('',(1.E0,0.E0,0.E0)); -#47355=AXIS2_PLACEMENT_3D('',#47352,#47353,#47354); -#47356=PLANE('',#47355); -#47357=ORIENTED_EDGE('',*,*,#47312,.F.); -#47358=ORIENTED_EDGE('',*,*,#45386,.F.); -#47359=ORIENTED_EDGE('',*,*,#22227,.T.); -#47361=ORIENTED_EDGE('',*,*,#47360,.F.); -#47362=EDGE_LOOP('',(#47357,#47358,#47359,#47361)); -#47363=FACE_OUTER_BOUND('',#47362,.F.); -#47365=CARTESIAN_POINT('',(-6.887409636269E0,3.E-1,1.295E1)); -#47366=DIRECTION('',(0.E0,0.E0,1.E0)); -#47367=DIRECTION('',(1.E0,0.E0,0.E0)); -#47368=AXIS2_PLACEMENT_3D('',#47365,#47366,#47367); -#47369=PLANE('',#47368); -#47371=ORIENTED_EDGE('',*,*,#47370,.T.); -#47373=ORIENTED_EDGE('',*,*,#47372,.F.); -#47374=ORIENTED_EDGE('',*,*,#24202,.F.); -#47375=ORIENTED_EDGE('',*,*,#45380,.F.); -#47376=EDGE_LOOP('',(#47371,#47373,#47374,#47375)); -#47377=FACE_OUTER_BOUND('',#47376,.F.); -#47379=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.295E1)); -#47380=DIRECTION('',(1.E0,0.E0,0.E0)); -#47381=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47382=AXIS2_PLACEMENT_3D('',#47379,#47380,#47381); -#47383=PLANE('',#47382); -#47384=ORIENTED_EDGE('',*,*,#47314,.F.); -#47385=ORIENTED_EDGE('',*,*,#47360,.T.); -#47386=ORIENTED_EDGE('',*,*,#22225,.T.); -#47387=ORIENTED_EDGE('',*,*,#47286,.F.); -#47388=EDGE_LOOP('',(#47384,#47385,#47386,#47387)); -#47389=FACE_OUTER_BOUND('',#47388,.F.); -#47391=CARTESIAN_POINT('',(-5.9E0,3.E-1,1.295E1)); -#47392=DIRECTION('',(1.E0,0.E0,0.E0)); -#47393=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47394=AXIS2_PLACEMENT_3D('',#47391,#47392,#47393); -#47395=PLANE('',#47394); -#47397=ORIENTED_EDGE('',*,*,#47396,.T.); -#47398=ORIENTED_EDGE('',*,*,#47302,.F.); -#47399=ORIENTED_EDGE('',*,*,#24204,.F.); -#47400=ORIENTED_EDGE('',*,*,#47372,.T.); -#47401=EDGE_LOOP('',(#47397,#47398,#47399,#47400)); -#47402=FACE_OUTER_BOUND('',#47401,.F.); -#47404=CARTESIAN_POINT('',(0.E0,2.5E-1,7.7E0)); -#47405=DIRECTION('',(0.E0,1.E0,0.E0)); -#47406=DIRECTION('',(1.E0,0.E0,0.E0)); -#47407=AXIS2_PLACEMENT_3D('',#47404,#47405,#47406); -#47408=PLANE('',#47407); -#47409=ORIENTED_EDGE('',*,*,#47370,.F.); -#47411=ORIENTED_EDGE('',*,*,#47410,.F.); -#47412=ORIENTED_EDGE('',*,*,#47298,.F.); -#47413=ORIENTED_EDGE('',*,*,#47396,.F.); -#47414=EDGE_LOOP('',(#47409,#47411,#47412,#47413)); -#47415=FACE_OUTER_BOUND('',#47414,.F.); -#47417=FILL_AREA_STYLE_COLOUR('',#15); -#47418=FILL_AREA_STYLE('',(#47417)); -#47419=SURFACE_STYLE_FILL_AREA(#47418); -#47420=SURFACE_SIDE_STYLE('',(#47419)); -#47421=SURFACE_STYLE_USAGE(.POSITIVE.,#47420); -#47422=PRESENTATION_STYLE_ASSIGNMENT((#47421)); -#47423=STYLED_ITEM('',(#47422),#47416); -#47424=CARTESIAN_POINT('',(0.E0,2.5E-1,7.7E0)); -#47425=DIRECTION('',(0.E0,1.E0,0.E0)); -#47426=DIRECTION('',(1.E0,0.E0,0.E0)); -#47427=AXIS2_PLACEMENT_3D('',#47424,#47425,#47426); -#47428=PLANE('',#47427); -#47430=ORIENTED_EDGE('',*,*,#47429,.F.); -#47432=ORIENTED_EDGE('',*,*,#47431,.F.); -#47434=ORIENTED_EDGE('',*,*,#47433,.F.); -#47436=ORIENTED_EDGE('',*,*,#47435,.F.); -#47437=EDGE_LOOP('',(#47430,#47432,#47434,#47436)); -#47438=FACE_OUTER_BOUND('',#47437,.F.); -#47440=FILL_AREA_STYLE_COLOUR('',#15); -#47441=FILL_AREA_STYLE('',(#47440)); -#47442=SURFACE_STYLE_FILL_AREA(#47441); -#47443=SURFACE_SIDE_STYLE('',(#47442)); -#47444=SURFACE_STYLE_USAGE(.POSITIVE.,#47443); -#47445=PRESENTATION_STYLE_ASSIGNMENT((#47444)); -#47446=STYLED_ITEM('',(#47445),#47439); -#47447=CARTESIAN_POINT('',(-6.693649167310E0,-2.5E-1,1.26E1)); -#47448=DIRECTION('',(0.E0,1.E0,0.E0)); -#47449=DIRECTION('',(1.E0,0.E0,0.E0)); -#47450=AXIS2_PLACEMENT_3D('',#47447,#47448,#47449); -#47451=CYLINDRICAL_SURFACE('',#47450,4.E-1); -#47452=ORIENTED_EDGE('',*,*,#45370,.T.); -#47453=ORIENTED_EDGE('',*,*,#47410,.T.); -#47454=ORIENTED_EDGE('',*,*,#45388,.F.); -#47455=ORIENTED_EDGE('',*,*,#47317,.F.); -#47456=EDGE_LOOP('',(#47452,#47453,#47454,#47455)); -#47457=FACE_OUTER_BOUND('',#47456,.F.); -#47459=FILL_AREA_STYLE_COLOUR('',#15); -#47460=FILL_AREA_STYLE('',(#47459)); -#47461=SURFACE_STYLE_FILL_AREA(#47460); -#47462=SURFACE_SIDE_STYLE('',(#47461)); -#47463=SURFACE_STYLE_USAGE(.NEGATIVE.,#47462); -#47464=PRESENTATION_STYLE_ASSIGNMENT((#47463)); -#47465=STYLED_ITEM('',(#47464),#47458); -#47466=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.225E1)); -#47467=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47468=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47469=AXIS2_PLACEMENT_3D('',#47466,#47467,#47468); -#47470=PLANE('',#47469); -#47471=ORIENTED_EDGE('',*,*,#47334,.F.); -#47472=ORIENTED_EDGE('',*,*,#45078,.F.); -#47473=ORIENTED_EDGE('',*,*,#22239,.T.); -#47475=ORIENTED_EDGE('',*,*,#47474,.F.); -#47476=EDGE_LOOP('',(#47471,#47472,#47473,#47475)); -#47477=FACE_OUTER_BOUND('',#47476,.F.); -#47479=CARTESIAN_POINT('',(7.887409636269E0,3.E-1,1.225E1)); -#47480=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47481=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47482=AXIS2_PLACEMENT_3D('',#47479,#47480,#47481); -#47483=PLANE('',#47482); -#47484=ORIENTED_EDGE('',*,*,#47429,.T.); -#47486=ORIENTED_EDGE('',*,*,#47485,.F.); -#47487=ORIENTED_EDGE('',*,*,#24190,.F.); -#47488=ORIENTED_EDGE('',*,*,#45068,.F.); -#47489=EDGE_LOOP('',(#47484,#47486,#47487,#47488)); -#47490=FACE_OUTER_BOUND('',#47489,.F.); -#47492=CARTESIAN_POINT('',(6.9E0,3.E-1,1.225E1)); -#47493=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47494=DIRECTION('',(0.E0,0.E0,1.E0)); -#47495=AXIS2_PLACEMENT_3D('',#47492,#47493,#47494); -#47496=PLANE('',#47495); -#47497=ORIENTED_EDGE('',*,*,#47336,.F.); -#47498=ORIENTED_EDGE('',*,*,#47474,.T.); -#47499=ORIENTED_EDGE('',*,*,#22237,.T.); -#47501=ORIENTED_EDGE('',*,*,#47500,.F.); -#47502=EDGE_LOOP('',(#47497,#47498,#47499,#47501)); -#47503=FACE_OUTER_BOUND('',#47502,.F.); -#47505=CARTESIAN_POINT('',(6.9E0,3.E-1,1.225E1)); -#47506=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47507=DIRECTION('',(0.E0,0.E0,1.E0)); -#47508=AXIS2_PLACEMENT_3D('',#47505,#47506,#47507); -#47509=PLANE('',#47508); -#47510=ORIENTED_EDGE('',*,*,#47435,.T.); -#47512=ORIENTED_EDGE('',*,*,#47511,.F.); -#47513=ORIENTED_EDGE('',*,*,#24192,.F.); -#47514=ORIENTED_EDGE('',*,*,#47485,.T.); -#47515=EDGE_LOOP('',(#47510,#47512,#47513,#47514)); -#47516=FACE_OUTER_BOUND('',#47515,.F.); -#47518=CARTESIAN_POINT('',(6.9E0,3.E-1,1.295E1)); -#47519=DIRECTION('',(0.E0,0.E0,1.E0)); -#47520=DIRECTION('',(1.E0,0.E0,0.E0)); -#47521=AXIS2_PLACEMENT_3D('',#47518,#47519,#47520); -#47522=PLANE('',#47521); -#47523=ORIENTED_EDGE('',*,*,#47338,.F.); -#47524=ORIENTED_EDGE('',*,*,#47500,.T.); -#47525=ORIENTED_EDGE('',*,*,#22235,.F.); -#47526=ORIENTED_EDGE('',*,*,#45090,.T.); -#47527=EDGE_LOOP('',(#47523,#47524,#47525,#47526)); -#47528=FACE_OUTER_BOUND('',#47527,.F.); -#47530=CARTESIAN_POINT('',(6.9E0,3.E-1,1.295E1)); -#47531=DIRECTION('',(0.E0,0.E0,1.E0)); -#47532=DIRECTION('',(1.E0,0.E0,0.E0)); -#47533=AXIS2_PLACEMENT_3D('',#47530,#47531,#47532); -#47534=PLANE('',#47533); -#47535=ORIENTED_EDGE('',*,*,#47433,.T.); -#47536=ORIENTED_EDGE('',*,*,#45096,.T.); -#47537=ORIENTED_EDGE('',*,*,#24194,.T.); -#47538=ORIENTED_EDGE('',*,*,#47511,.T.); -#47539=EDGE_LOOP('',(#47535,#47536,#47537,#47538)); -#47540=FACE_OUTER_BOUND('',#47539,.F.); -#47542=CARTESIAN_POINT('',(7.693649167310E0,-2.5E-1,1.26E1)); -#47543=DIRECTION('',(0.E0,1.E0,0.E0)); -#47544=DIRECTION('',(1.E0,0.E0,0.E0)); -#47545=AXIS2_PLACEMENT_3D('',#47542,#47543,#47544); -#47546=CYLINDRICAL_SURFACE('',#47545,4.E-1); -#47547=ORIENTED_EDGE('',*,*,#45080,.F.); -#47548=ORIENTED_EDGE('',*,*,#47340,.F.); -#47549=ORIENTED_EDGE('',*,*,#45098,.T.); -#47550=ORIENTED_EDGE('',*,*,#47431,.T.); -#47551=EDGE_LOOP('',(#47547,#47548,#47549,#47550)); -#47552=FACE_OUTER_BOUND('',#47551,.F.); -#47554=FILL_AREA_STYLE_COLOUR('',#15); -#47555=FILL_AREA_STYLE('',(#47554)); -#47556=SURFACE_STYLE_FILL_AREA(#47555); -#47557=SURFACE_SIDE_STYLE('',(#47556)); -#47558=SURFACE_STYLE_USAGE(.NEGATIVE.,#47557); -#47559=PRESENTATION_STYLE_ASSIGNMENT((#47558)); -#47560=STYLED_ITEM('',(#47559),#47553); -#47561=CARTESIAN_POINT('',(-6.5E0,-3.E-1,1.37E1)); -#47562=DIRECTION('',(0.E0,0.E0,1.E0)); -#47563=DIRECTION('',(1.E0,0.E0,0.E0)); -#47564=AXIS2_PLACEMENT_3D('',#47561,#47562,#47563); -#47565=PLANE('',#47564); -#47566=ORIENTED_EDGE('',*,*,#22231,.F.); -#47567=ORIENTED_EDGE('',*,*,#45383,.T.); -#47568=ORIENTED_EDGE('',*,*,#24198,.T.); -#47569=ORIENTED_EDGE('',*,*,#45093,.F.); -#47570=EDGE_LOOP('',(#47566,#47567,#47568,#47569)); -#47571=FACE_OUTER_BOUND('',#47570,.F.); -#47573=CARTESIAN_POINT('',(-7.55E0,3.E-1,-1.2635E1)); -#47574=DIRECTION('',(0.E0,1.E0,0.E0)); -#47575=DIRECTION('',(1.E0,0.E0,0.E0)); -#47576=AXIS2_PLACEMENT_3D('',#47573,#47574,#47575); -#47577=CYLINDRICAL_SURFACE('',#47576,2.5E-1); -#47578=ORIENTED_EDGE('',*,*,#24029,.T.); -#47579=ORIENTED_EDGE('',*,*,#23968,.T.); -#47580=ORIENTED_EDGE('',*,*,#24271,.T.); -#47581=ORIENTED_EDGE('',*,*,#23941,.F.); -#47582=EDGE_LOOP('',(#47578,#47579,#47580,#47581)); -#47583=FACE_OUTER_BOUND('',#47582,.F.); -#47585=FILL_AREA_STYLE_COLOUR('',#15); -#47586=FILL_AREA_STYLE('',(#47585)); -#47587=SURFACE_STYLE_FILL_AREA(#47586); -#47588=SURFACE_SIDE_STYLE('',(#47587)); -#47589=SURFACE_STYLE_USAGE(.NEGATIVE.,#47588); -#47590=PRESENTATION_STYLE_ASSIGNMENT((#47589)); -#47591=STYLED_ITEM('',(#47590),#47584); -#47592=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2335E1)); -#47593=DIRECTION('',(0.E0,0.E0,1.E0)); -#47594=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47595=AXIS2_PLACEMENT_3D('',#47592,#47593,#47594); -#47596=PLANE('',#47595); -#47597=ORIENTED_EDGE('',*,*,#22151,.T.); -#47599=ORIENTED_EDGE('',*,*,#47598,.T.); -#47600=ORIENTED_EDGE('',*,*,#24022,.T.); -#47601=ORIENTED_EDGE('',*,*,#23937,.F.); -#47602=EDGE_LOOP('',(#47597,#47599,#47600,#47601)); -#47603=FACE_OUTER_BOUND('',#47602,.F.); -#47605=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.2935E1)); -#47606=DIRECTION('',(1.E0,0.E0,0.E0)); -#47607=DIRECTION('',(0.E0,0.E0,1.E0)); -#47608=AXIS2_PLACEMENT_3D('',#47605,#47606,#47607); -#47609=PLANE('',#47608); -#47610=ORIENTED_EDGE('',*,*,#22149,.F.); -#47612=ORIENTED_EDGE('',*,*,#47611,.T.); -#47613=ORIENTED_EDGE('',*,*,#24024,.T.); -#47614=ORIENTED_EDGE('',*,*,#47598,.F.); -#47615=EDGE_LOOP('',(#47610,#47612,#47613,#47614)); -#47616=FACE_OUTER_BOUND('',#47615,.F.); -#47618=CARTESIAN_POINT('',(-7.640579250739E0,-3.E-1,-1.2935E1)); -#47619=DIRECTION('',(0.E0,0.E0,-1.E0)); -#47620=DIRECTION('',(1.E0,0.E0,0.E0)); -#47621=AXIS2_PLACEMENT_3D('',#47618,#47619,#47620); -#47622=PLANE('',#47621); -#47623=ORIENTED_EDGE('',*,*,#22147,.F.); -#47624=ORIENTED_EDGE('',*,*,#23957,.T.); -#47625=ORIENTED_EDGE('',*,*,#24026,.T.); -#47626=ORIENTED_EDGE('',*,*,#47611,.F.); -#47627=EDGE_LOOP('',(#47623,#47624,#47625,#47626)); -#47628=FACE_OUTER_BOUND('',#47627,.F.); -#47630=CARTESIAN_POINT('',(-7.15E0,-3.E-1,-1.3435E1)); -#47631=DIRECTION('',(0.E0,0.E0,1.E0)); -#47632=DIRECTION('',(-1.E0,0.E0,0.E0)); -#47633=AXIS2_PLACEMENT_3D('',#47630,#47631,#47632); -#47634=PLANE('',#47633); -#47635=ORIENTED_EDGE('',*,*,#22143,.T.); -#47636=ORIENTED_EDGE('',*,*,#23889,.T.); -#47637=ORIENTED_EDGE('',*,*,#24047,.T.); -#47638=ORIENTED_EDGE('',*,*,#23960,.F.); -#47639=EDGE_LOOP('',(#47635,#47636,#47637,#47638)); -#47640=FACE_OUTER_BOUND('',#47639,.F.); -#47642=CLOSED_SHELL('',(#22491,#22513,#22526,#22536,#22555,#22574,#22593,#22614, -#22626,#22640,#22652,#22666,#22678,#22693,#22706,#22716,#22735,#22754,#22773, -#22794,#22806,#22820,#22832,#22846,#22858,#22873,#22886,#22896,#22915,#22934, -#22953,#22974,#22986,#23000,#23012,#23026,#23038,#23053,#23066,#23076,#23095, -#23114,#23133,#23154,#23166,#23180,#23192,#23206,#23218,#23233,#23246,#23256, -#23275,#23294,#23313,#23334,#23346,#23360,#23372,#23386,#23398,#23413,#23426, -#23436,#23455,#23474,#23493,#23514,#23526,#23540,#23552,#23566,#23578,#23593, -#23607,#23621,#23634,#23646,#23669,#23692,#23715,#23736,#23749,#23762,#23774, -#23788,#23801,#23814,#23826,#23840,#23853,#23866,#23878,#23893,#23907,#23926, -#23949,#23972,#23990,#24008,#24033,#24056,#24076,#24089,#24101,#24114,#24358, -#24398,#24467,#24494,#24507,#24520,#24533,#24546,#24567,#26328,#26356,#26384, -#26424,#26464,#26496,#26536,#26576,#26604,#26632,#26672,#26712,#26744,#26758, -#26802,#26846,#26860,#26888,#26916,#26956,#26996,#27010,#27024,#27056,#27074, -#27087,#27100,#27113,#27125,#27138,#27151,#27164,#27176,#27191,#27205,#27219, -#27233,#27247,#27261,#27275,#27289,#27303,#27317,#27331,#27345,#27359,#27373, -#27387,#27401,#27415,#27429,#27442,#27513,#27544,#27695,#27824,#27895,#27934, -#27969,#28064,#28159,#28182,#28251,#28274,#28297,#28336,#28487,#28528,#28625, -#28656,#28807,#28936,#29007,#29030,#29125,#29148,#29217,#29240,#29263,#29308, -#29337,#29442,#29547,#29586,#29609,#29706,#29737,#29888,#30017,#30088,#30109, -#30122,#30135,#30148,#30161,#30174,#30187,#30200,#30213,#30225,#30239,#30252, -#30265,#30278,#30291,#30304,#30317,#30330,#30343,#30355,#30369,#30382,#30395, -#30408,#30421,#30434,#30447,#30459,#30473,#30486,#30499,#30512,#30525,#30538, -#30551,#30564,#30577,#30590,#30603,#30616,#30629,#30642,#30655,#30668,#30681, -#30694,#30707,#30720,#30733,#30746,#30759,#30772,#30785,#30798,#30811,#30824, -#30837,#30850,#30863,#30876,#30889,#30901,#30915,#30928,#30941,#30954,#30967, -#30980,#30993,#31006,#31019,#31032,#31045,#31058,#31071,#31084,#31097,#31109, -#31123,#31136,#31149,#31162,#31175,#31188,#31201,#31214,#31227,#31240,#31253, -#31266,#31279,#31292,#31305,#31317,#31331,#31344,#31357,#31370,#31383,#31396, -#31409,#31422,#31435,#31448,#31461,#31474,#31487,#31500,#31513,#31526,#31539, -#31552,#31565,#31578,#31591,#31604,#31617,#31630,#31643,#31656,#31669,#31682, -#31695,#31708,#31721,#31734,#31747,#31760,#31773,#31786,#31799,#31812,#31825, -#31838,#31851,#31864,#31877,#31890,#31903,#31916,#31929,#31942,#31955,#31968, -#31981,#31994,#32007,#32020,#32033,#32046,#32058,#32072,#32085,#32098,#32111, -#32124,#32137,#32150,#32163,#32176,#32189,#32202,#32215,#32228,#32241,#32254, -#32267,#32280,#32293,#32306,#32319,#32332,#32345,#32358,#32371,#32384,#32397, -#32410,#32422,#32436,#32449,#32462,#32475,#32488,#32501,#32514,#32527,#32540, -#32553,#32566,#32578,#32592,#32605,#32618,#32631,#32644,#32657,#32670,#32683, -#32696,#32708,#32722,#32735,#32748,#32761,#32774,#32787,#32800,#32813,#32826, -#32839,#32852,#32865,#32878,#32891,#32904,#32917,#32930,#32943,#32956,#32969, -#32982,#32995,#33008,#33021,#33034,#33047,#33060,#33073,#33086,#33099,#33112, -#33125,#33138,#33151,#33164,#33177,#33190,#33203,#33216,#33228,#33242,#33255, -#33268,#33281,#33294,#33307,#33320,#33333,#33346,#33359,#33372,#33385,#33398, -#33411,#33424,#33437,#33450,#33463,#33476,#33489,#33502,#33515,#33528,#33541, -#33554,#33567,#33580,#33593,#33606,#33619,#33632,#33645,#33658,#33671,#33684, -#33697,#33710,#33723,#33736,#33748,#33762,#33775,#33788,#33800,#33814,#33827, -#33840,#33853,#33866,#33879,#33892,#33905,#33918,#33931,#33944,#33957,#33970, -#33982,#33996,#34009,#34022,#34035,#34048,#34061,#34074,#34087,#34100,#34113, -#34126,#34138,#34152,#34165,#34178,#34190,#34204,#34217,#34230,#34242,#34256, -#34269,#34282,#34295,#34308,#34321,#34334,#34347,#34360,#34373,#34386,#34398, -#34412,#34425,#34438,#34451,#34464,#34477,#34490,#34503,#34516,#34529,#34542, -#34555,#34568,#34581,#34594,#34607,#34620,#34633,#34646,#34659,#34672,#34685, -#34698,#34711,#34724,#34737,#34750,#34763,#34776,#34789,#34802,#34815,#34828, -#34840,#34854,#34867,#34880,#34893,#34906,#34919,#34932,#34945,#34958,#34971, -#34984,#34997,#35010,#35023,#35036,#35048,#35062,#35075,#35088,#35101,#35114, -#35127,#35140,#35153,#35166,#35179,#35192,#35205,#35218,#35231,#35244,#35256, -#35270,#35283,#35296,#35309,#35322,#35335,#35348,#35361,#35374,#35387,#35400, -#35413,#35425,#35439,#35452,#35465,#35478,#35491,#35504,#35517,#35530,#35543, -#35556,#35569,#35582,#35595,#35608,#35621,#35634,#35647,#35660,#35672,#35686, -#35699,#35712,#35725,#35738,#35751,#35764,#35777,#35790,#35802,#35816,#35829, -#35842,#35855,#35868,#35881,#35894,#35907,#35920,#35932,#35946,#35959,#35972, -#35985,#35998,#36011,#36024,#36036,#36050,#36063,#36076,#36089,#36102,#36115, -#36128,#36141,#36154,#36167,#36180,#36193,#36206,#36219,#36232,#36245,#36258, -#36271,#36284,#36297,#36310,#36323,#36336,#36349,#36362,#36375,#36388,#36401, -#36414,#36427,#36440,#36453,#36466,#36478,#36492,#36505,#36518,#36531,#36544, -#36557,#36570,#36583,#36596,#36609,#36622,#36635,#36648,#36661,#36674,#36686, -#36700,#36713,#36726,#36739,#36752,#36765,#36778,#36791,#36804,#36817,#36830, -#36843,#36856,#36869,#36882,#36894,#36908,#36921,#36934,#36947,#36960,#36973, -#36986,#36999,#37012,#37025,#37038,#37051,#37064,#37077,#37090,#37103,#37116, -#37129,#37142,#37155,#37168,#37181,#37194,#37207,#37220,#37233,#37246,#37259, -#37272,#37285,#37298,#37311,#37324,#37337,#37350,#37363,#37376,#37389,#37402, -#37415,#37428,#37441,#37454,#37467,#37480,#37493,#37506,#37519,#37532,#37545, -#37558,#37571,#37584,#37597,#37610,#37623,#37635,#37649,#37662,#37675,#37688, -#37701,#37714,#37727,#37740,#37753,#37766,#37779,#37792,#37805,#37818,#37831, -#37844,#37857,#37870,#37883,#37896,#37909,#37922,#37935,#37948,#37961,#37974, -#37987,#37999,#38013,#38026,#38039,#38051,#38065,#38078,#38091,#38104,#38117, -#38130,#38143,#38156,#38169,#38182,#38195,#38208,#38221,#38234,#38247,#38260, -#38273,#38286,#38299,#38312,#38325,#38338,#38351,#38364,#38377,#38390,#38403, -#38416,#38429,#38442,#38455,#38468,#38481,#38494,#38507,#38520,#38533,#38546, -#38559,#38571,#38585,#38598,#38611,#38623,#38637,#38650,#38663,#38676,#38689, -#38702,#38715,#38728,#38741,#38754,#38767,#38780,#38793,#38805,#38819,#38832, -#38845,#38858,#38871,#38884,#38897,#38910,#38923,#38936,#38949,#38961,#38975, -#38988,#39001,#39013,#39027,#39040,#39053,#39065,#39079,#39092,#39105,#39118, -#39131,#39144,#39157,#39170,#39183,#39196,#39208,#39222,#39235,#39247,#39261, -#39274,#39287,#39300,#39313,#39326,#39338,#39352,#39365,#39378,#39391,#39404, -#39417,#39430,#39443,#39456,#39469,#39482,#39495,#39508,#39521,#39534,#39547, -#39560,#39573,#39586,#39599,#39612,#39625,#39638,#39651,#39664,#39676,#39690, -#39703,#39716,#39729,#39742,#39755,#39768,#39781,#39794,#39807,#39820,#39833, -#39846,#39859,#39872,#39885,#39898,#39910,#39924,#39937,#39950,#39963,#39976, -#39989,#40002,#40015,#40028,#40041,#40054,#40067,#40080,#40093,#40106,#40119, -#40132,#40145,#40158,#40171,#40184,#40197,#40210,#40223,#40236,#40248,#40262, -#40275,#40288,#40301,#40314,#40327,#40340,#40353,#40366,#40379,#40392,#40405, -#40418,#40431,#40444,#40457,#40470,#40482,#40496,#40509,#40522,#40535,#40548, -#40561,#40574,#40586,#40600,#40613,#40625,#40639,#40652,#40665,#40677,#40691, -#40704,#40717,#40730,#40743,#40756,#40769,#40782,#40795,#40808,#40821,#40834, -#40847,#40860,#40873,#40886,#40899,#40912,#40924,#40938,#40951,#40964,#40977, -#40990,#41003,#41016,#41029,#41042,#41054,#41068,#41081,#41094,#41107,#41120, -#41133,#41146,#41159,#41172,#41184,#41198,#41211,#41224,#41237,#41250,#41263, -#41276,#41288,#41302,#41315,#41328,#41341,#41354,#41367,#41380,#41393,#41406, -#41419,#41432,#41445,#41458,#41471,#41484,#41497,#41510,#41523,#41536,#41549, -#41562,#41575,#41588,#41601,#41614,#41627,#41640,#41653,#41666,#41679,#41692, -#41705,#41718,#41730,#41744,#41757,#41770,#41783,#41796,#41809,#41822,#41835, -#41848,#41861,#41874,#41887,#41900,#41913,#41926,#41938,#41952,#41965,#41978, -#41991,#42004,#42017,#42030,#42043,#42056,#42069,#42082,#42095,#42108,#42121, -#42134,#42146,#42160,#42173,#42186,#42199,#42212,#42225,#42238,#42251,#42264, -#42277,#42290,#42303,#42316,#42329,#42342,#42355,#42368,#42381,#42394,#42407, -#42420,#42433,#42446,#42459,#42472,#42485,#42498,#42511,#42524,#42537,#42550, -#42563,#42576,#42589,#42602,#42615,#42628,#42641,#42654,#42667,#42680,#42693, -#42706,#42719,#42732,#42745,#42758,#42771,#42784,#42797,#42810,#42823,#42836, -#42849,#42862,#42875,#42887,#42901,#42914,#42927,#42940,#42953,#42966,#42979, -#42992,#43005,#43018,#43031,#43044,#43057,#43070,#43083,#43096,#43109,#43122, -#43135,#43148,#43161,#43174,#43187,#43200,#43213,#43226,#43239,#43251,#43266, -#43286,#43307,#43327,#43339,#43358,#43393,#43432,#43467,#43554,#43589,#43601, -#43638,#43658,#43670,#43690,#43709,#43722,#43741,#43754,#43767,#43786,#43799, -#43818,#43830,#43850,#43869,#43881,#43895,#43914,#43927,#43946,#43959,#43978, -#43991,#44009,#44023,#44042,#44055,#44074,#44087,#44106,#44119,#44138,#44151, -#44169,#44190,#44203,#44222,#44235,#44255,#44288,#44301,#44358,#44371,#44390, -#44403,#44422,#44435,#44454,#44467,#44493,#44506,#44525,#44537,#44551,#44570, -#44583,#44602,#44615,#44634,#44647,#44666,#44679,#44698,#44711,#44729,#44742, -#44755,#44767,#44780,#44793,#44805,#44818,#44831,#44843,#44856,#44869,#44881, -#44893,#44913,#44930,#44952,#44974,#44996,#45018,#45040,#45062,#45084,#45102, -#45116,#45130,#45146,#45168,#45189,#45204,#45222,#45242,#45264,#45286,#45308, -#45330,#45352,#45374,#45392,#45405,#45419,#45431,#45444,#45457,#45479,#45498, -#45517,#45537,#45550,#45562,#45574,#45586,#45600,#45614,#45629,#45652,#45672, -#45686,#45698,#45711,#45724,#45747,#45766,#45786,#45799,#45812,#45825,#45837, -#45849,#45861,#45882,#45896,#45911,#45934,#45954,#45968,#45980,#45993,#46006, -#46029,#46048,#46068,#46081,#46094,#46107,#46119,#46131,#46143,#46164,#46178, -#46193,#46216,#46236,#46250,#46262,#46275,#46288,#46311,#46330,#46350,#46363, -#46376,#46389,#46401,#46413,#46425,#46446,#46460,#46475,#46498,#46518,#46532, -#46544,#46557,#46570,#46593,#46612,#46632,#46645,#46658,#46671,#46683,#46695, -#46707,#46728,#46742,#46757,#46780,#46800,#46814,#46826,#46839,#46852,#46875, -#46894,#46914,#46927,#46940,#46953,#46965,#46977,#46989,#47010,#47024,#47039, -#47062,#47082,#47096,#47108,#47121,#47134,#47157,#47176,#47196,#47209,#47222, -#47235,#47247,#47259,#47271,#47292,#47306,#47321,#47344,#47364,#47378,#47390, -#47403,#47416,#47439,#47458,#47478,#47491,#47504,#47517,#47529,#47541,#47553, -#47572,#47584,#47604,#47617,#47629,#47641)); -#47643=MANIFOLD_SOLID_BREP('',#47642); -#47645=DIMENSIONAL_EXPONENTS(0.E0,0.E0,0.E0,0.E0,0.E0,0.E0,0.E0); -#47647=PLANE_ANGLE_MEASURE_WITH_UNIT(PLANE_ANGLE_MEASURE(1.745329251994E-2), -#47646); -#47648=(CONVERSION_BASED_UNIT('DEGREE',#47647)NAMED_UNIT(*)PLANE_ANGLE_UNIT()); -#47650=UNCERTAINTY_MEASURE_WITH_UNIT(LENGTH_MEASURE(5.492578263035E-3),#47644, -'closure', -'Maximum model space distance between geometric entities at asserted connectivities'); -#47653=MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION('',(#22498, -#22543,#22562,#22581,#22600,#22723,#22742,#22761,#22780,#22903,#22922,#22941, -#22960,#23083,#23102,#23121,#23140,#23263,#23282,#23301,#23320,#23443,#23462, -#23481,#23500,#23653,#23676,#23699,#23722,#24015,#24040,#24063,#24121,#24365, -#27520,#27551,#27702,#27831,#27902,#27941,#27976,#28071,#28166,#28189,#28258, -#28281,#28304,#28343,#28494,#28535,#28632,#28663,#28814,#28943,#29014,#29037, -#29132,#29155,#29224,#29247,#29270,#29315,#29344,#29449,#29554,#29593,#29616, -#29713,#29744,#29895,#30024,#30095,#43346,#43365,#43400,#43439,#43474,#43561, -#44900,#45153,#45175,#45464,#45486,#45505,#45524,#45636,#45659,#45731,#45754, -#45773,#45868,#45918,#45941,#46013,#46036,#46055,#46150,#46200,#46223,#46295, -#46318,#46337,#46432,#46482,#46505,#46577,#46600,#46619,#46714,#46764,#46787, -#46859,#46882,#46901,#46996,#47046,#47069,#47141,#47164,#47183,#47278,#47328, -#47351,#47423,#47446,#47465,#47560,#47591),#47651); -#47654=APPLICATION_CONTEXT( -'CONFIGURATION CONTROLLED 3D DESIGNS OF MECHANICAL PARTS AND ASSEMBLIES'); -#47655=APPLICATION_PROTOCOL_DEFINITION('international standard', -'config_control_design',1994,#47654); -#47656=DESIGN_CONTEXT('',#47654,'design'); -#47657=MECHANICAL_CONTEXT('',#47654,'mechanical'); -#47658=PRODUCT('BT832X','BT832X','NOT SPECIFIED',(#47657)); -#47659=PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE('13','LAST_VERSION', -#47658,.MADE.); -#47663=PRODUCT_CATEGORY('part',''); -#47664=PRODUCT_RELATED_PRODUCT_CATEGORY('detail','',(#47658)); -#47665=PRODUCT_CATEGORY_RELATIONSHIP('','',#47663,#47664); -#47666=SECURITY_CLASSIFICATION_LEVEL('unclassified'); -#47667=SECURITY_CLASSIFICATION('','',#47666); -#47668=CC_DESIGN_SECURITY_CLASSIFICATION(#47667,(#47659)); -#47669=APPROVAL_STATUS('approved'); -#47670=APPROVAL(#47669,''); -#47671=CC_DESIGN_APPROVAL(#47670,(#47667,#47659,#47660)); -#47672=CALENDAR_DATE(118,11,12); -#47673=COORDINATED_UNIVERSAL_TIME_OFFSET(8,0,.AHEAD.); -#47674=LOCAL_TIME(15,4,2.E1,#47673); -#47675=DATE_AND_TIME(#47672,#47674); -#47676=APPROVAL_DATE_TIME(#47675,#47670); -#47677=DATE_TIME_ROLE('creation_date'); -#47678=CC_DESIGN_DATE_AND_TIME_ASSIGNMENT(#47675,#47677,(#47660)); -#47679=DATE_TIME_ROLE('classification_date'); -#47680=CC_DESIGN_DATE_AND_TIME_ASSIGNMENT(#47675,#47679,(#47667)); -#47681=PERSON('UNSPECIFIED','UNSPECIFIED',$,$,$,$); -#47682=ORGANIZATION('UNSPECIFIED','UNSPECIFIED','UNSPECIFIED'); -#47683=PERSON_AND_ORGANIZATION(#47681,#47682); -#47684=APPROVAL_ROLE('approver'); -#47685=APPROVAL_PERSON_ORGANIZATION(#47683,#47670,#47684); -#47686=PERSON_AND_ORGANIZATION_ROLE('creator'); -#47687=CC_DESIGN_PERSON_AND_ORGANIZATION_ASSIGNMENT(#47683,#47686,(#47659, -#47660)); -#47688=PERSON_AND_ORGANIZATION_ROLE('design_supplier'); -#47689=CC_DESIGN_PERSON_AND_ORGANIZATION_ASSIGNMENT(#47683,#47688,(#47659)); -#47690=PERSON_AND_ORGANIZATION_ROLE('classification_officer'); -#47691=CC_DESIGN_PERSON_AND_ORGANIZATION_ASSIGNMENT(#47683,#47690,(#47667)); -#47692=PERSON_AND_ORGANIZATION_ROLE('design_owner'); -#47693=CC_DESIGN_PERSON_AND_ORGANIZATION_ASSIGNMENT(#47683,#47692,(#47658)); -#1=COLOUR_RGB('',0.E0,0.E0,5.019607843137E-1); -#2=COLOUR_RGB('',0.E0,3.75E-1,5.E-1); -#3=DRAUGHTING_PRE_DEFINED_COLOUR('green'); -#4=COLOUR_RGB('',1.1E-2,1.2E-2,1.E0); -#5=COLOUR_RGB('',1.1E-1,1.1E-1,1.1E-1); -#6=COLOUR_RGB('',2.E-1,2.E-1,2.E-1); -#7=COLOUR_RGB('',3.92E-1,1.2E-2,1.2E-2); -#8=COLOUR_RGB('',4.1E-1,0.E0,2.2E-1); -#9=COLOUR_RGB('',5.019607843137E-1,0.E0,0.E0); -#10=COLOUR_RGB('',5.019607843137E-1,5.019607843137E-1,2.509803921569E-1); -#11=COLOUR_RGB('',5.019607843137E-1,5.019607843137E-1,1.E0); -#12=COLOUR_RGB('',6.E-1,3.019607843137E-1,0.E0); -#13=COLOUR_RGB('',8.392156862745E-1,8.392156862745E-1,8.392156862745E-1); -#14=COLOUR_RGB('',8.784E-1,9.49E-1,1.E0); -#15=COLOUR_RGB('',9.4902E-1,7.56863E-1,1.76471E-1); -#16=COLOUR_RGB('',9.6E-1,9.6E-1,9.6E-1); -#17=COLOUR_RGB('',9.6E-1,9.6E-1,9.6E-1); -#18=COLOUR_RGB('',9.8E-1,6.27E-1,0.E0); -#19=DRAUGHTING_PRE_DEFINED_COLOUR('red'); -#20=DRAUGHTING_PRE_DEFINED_COLOUR('magenta'); -#21=DRAUGHTING_PRE_DEFINED_COLOUR('yellow'); -#22=COLOUR_RGB('',1.E0,1.E0,9.49E-1); -#23=DRAUGHTING_PRE_DEFINED_COLOUR('white'); -#28=CIRCLE('',#27,3.E-1); -#33=CIRCLE('',#32,3.E-1); -#38=CIRCLE('',#37,3.E-1); -#43=CIRCLE('',#42,3.E-1); -#48=CIRCLE('',#47,3.E-1); -#53=CIRCLE('',#52,3.E-1); -#58=CIRCLE('',#57,3.E-1); -#63=CIRCLE('',#62,3.E-1); -#68=CIRCLE('',#67,3.E-1); -#73=CIRCLE('',#72,3.E-1); -#78=CIRCLE('',#77,3.E-1); -#83=CIRCLE('',#82,3.E-1); -#88=CIRCLE('',#87,3.E-1); -#93=CIRCLE('',#92,3.E-1); -#98=CIRCLE('',#97,3.E-1); -#103=CIRCLE('',#102,3.E-1); -#108=CIRCLE('',#107,3.E-1); -#113=CIRCLE('',#112,3.E-1); -#118=CIRCLE('',#117,3.E-1); -#123=CIRCLE('',#122,3.E-1); -#128=CIRCLE('',#127,3.E-1); -#133=CIRCLE('',#132,3.E-1); -#138=CIRCLE('',#137,3.E-1); -#143=CIRCLE('',#142,3.E-1); -#148=CIRCLE('',#147,3.E-1); -#153=CIRCLE('',#152,3.E-1); -#158=CIRCLE('',#157,3.E-1); -#163=CIRCLE('',#162,3.E-1); -#168=CIRCLE('',#167,3.E-1); -#173=CIRCLE('',#172,3.E-1); -#178=CIRCLE('',#177,3.E-1); -#183=CIRCLE('',#182,3.E-1); -#188=CIRCLE('',#187,3.E-1); -#193=CIRCLE('',#192,3.E-1); -#198=CIRCLE('',#197,3.E-1); -#203=CIRCLE('',#202,3.E-1); -#208=CIRCLE('',#207,3.E-1); -#213=CIRCLE('',#212,3.E-1); -#218=CIRCLE('',#217,3.E-1); -#223=CIRCLE('',#222,3.E-1); -#228=CIRCLE('',#227,3.E-1); -#233=CIRCLE('',#232,3.E-1); -#238=CIRCLE('',#237,3.E-1); -#243=CIRCLE('',#242,3.E-1); -#248=CIRCLE('',#247,3.E-1); -#253=CIRCLE('',#252,3.E-1); -#258=CIRCLE('',#257,3.E-1); -#263=CIRCLE('',#262,3.E-1); -#668=CIRCLE('',#667,3.E-1); -#673=CIRCLE('',#672,3.E-1); -#678=CIRCLE('',#677,3.E-1); -#683=CIRCLE('',#682,3.E-1); -#688=CIRCLE('',#687,3.E-1); -#693=CIRCLE('',#692,3.E-1); -#698=CIRCLE('',#697,3.E-1); -#703=CIRCLE('',#702,3.E-1); -#740=CIRCLE('',#739,3.E-1); -#745=CIRCLE('',#744,3.E-1); -#750=CIRCLE('',#749,3.E-1); -#755=CIRCLE('',#754,3.E-1); -#760=CIRCLE('',#759,3.E-1); -#765=CIRCLE('',#764,3.E-1); -#770=CIRCLE('',#769,3.E-1); -#775=CIRCLE('',#774,3.E-1); -#812=CIRCLE('',#811,3.E-1); -#817=CIRCLE('',#816,3.E-1); -#822=CIRCLE('',#821,3.E-1); -#827=CIRCLE('',#826,3.E-1); -#832=CIRCLE('',#831,3.E-1); -#837=CIRCLE('',#836,3.E-1); -#842=CIRCLE('',#841,3.E-1); -#847=CIRCLE('',#846,3.E-1); -#884=CIRCLE('',#883,3.E-1); -#889=CIRCLE('',#888,3.E-1); -#894=CIRCLE('',#893,3.E-1); -#899=CIRCLE('',#898,3.E-1); -#904=CIRCLE('',#903,3.E-1); -#909=CIRCLE('',#908,3.E-1); -#914=CIRCLE('',#913,3.E-1); -#919=CIRCLE('',#918,3.E-1); -#956=CIRCLE('',#955,3.E-1); -#961=CIRCLE('',#960,3.E-1); -#966=CIRCLE('',#965,3.E-1); -#971=CIRCLE('',#970,3.E-1); -#976=CIRCLE('',#975,3.E-1); -#981=CIRCLE('',#980,3.E-1); -#986=CIRCLE('',#985,3.E-1); -#991=CIRCLE('',#990,3.E-1); -#1028=CIRCLE('',#1027,3.E-1); -#1033=CIRCLE('',#1032,3.E-1); -#1038=CIRCLE('',#1037,3.E-1); -#1043=CIRCLE('',#1042,3.E-1); -#1048=CIRCLE('',#1047,3.E-1); -#1053=CIRCLE('',#1052,3.E-1); -#1058=CIRCLE('',#1057,3.E-1); -#1063=CIRCLE('',#1062,3.E-1); -#1344=CIRCLE('',#1343,2.5E-1); -#1349=CIRCLE('',#1348,2.5E-1); -#6124=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6118,#6119,#6120,#6121,#6122,#6123), -.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.334642613559E-1,6.665357386497E-1,1.E0), -.UNSPECIFIED.); -#6131=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6125,#6126,#6127,#6128,#6129,#6130), -.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.390786838150E-1,6.609213161849E-1,1.E0), -.UNSPECIFIED.); -#6136=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6132,#6133,#6134,#6135),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6150=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6137,#6138,#6139,#6140,#6141,#6142,#6143, -#6144,#6145,#6146,#6147,#6148,#6149),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1, -4),(0.E0,1.052706058146E-1,2.046623773364E-1,3.043975717067E-1, -4.026733828993E-1,5.004840316358E-1,5.982547988397E-1,6.963900106079E-1, -7.959497445438E-1,8.950977436735E-1,1.E0),.UNSPECIFIED.); -#6177=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6155,#6156,#6157,#6158,#6159,#6160,#6161, -#6162,#6163,#6164,#6165,#6166,#6167,#6168,#6169,#6170,#6171,#6172,#6173,#6174, -#6175,#6176),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,4),( -0.E0,7.452102549414E-2,1.637067914881E-1,2.508762869762E-1,3.310475071878E-1, -3.980380134526E-1,4.632870319512E-1,5.162497987040E-1,5.663752923082E-1, -6.113661267213E-1,6.510922663256E-1,6.905656038668E-1,7.358492893007E-1, -7.856597008070E-1,8.286974312854E-1,8.704349301340E-1,9.049072803385E-1, -9.365789321279E-1,9.655866536222E-1,1.E0),.UNSPECIFIED.); -#6188=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6182,#6183,#6184,#6185,#6186,#6187), -.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.352599494522E-1,6.647400505432E-1,1.E0), -.UNSPECIFIED.); -#6193=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6189,#6190,#6191,#6192),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6202=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6198,#6199,#6200,#6201),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6211=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6207,#6208,#6209,#6210),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6224=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6220,#6221,#6222,#6223),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6233=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6229,#6230,#6231,#6232),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6238=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6234,#6235,#6236,#6237),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6247=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6243,#6244,#6245,#6246),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6256=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6252,#6253,#6254,#6255),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6265=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6261,#6262,#6263,#6264),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6274=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6270,#6271,#6272,#6273),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6283=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6279,#6280,#6281,#6282),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6292=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6288,#6289,#6290,#6291),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6301=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6297,#6298,#6299,#6300),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6310=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6306,#6307,#6308,#6309),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6319=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6315,#6316,#6317,#6318),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6328=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6324,#6325,#6326,#6327),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6335=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6329,#6330,#6331,#6332,#6333,#6334), -.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.345015310528E-1,6.654984689528E-1,1.E0), -.UNSPECIFIED.); -#6344=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6340,#6341,#6342,#6343),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6361=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6349,#6350,#6351,#6352,#6353,#6354,#6355, -#6356,#6357,#6358,#6359,#6360),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,4), -(0.E0,1.174888978136E-1,2.277290966675E-1,3.374615345415E-1,4.464350365856E-1, -5.550456732220E-1,6.638625954523E-1,7.733019360617E-1,8.831119336622E-1,1.E0), -.UNSPECIFIED.); -#6370=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6366,#6367,#6368,#6369),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6379=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6375,#6376,#6377,#6378),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6388=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6384,#6385,#6386,#6387),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6436=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6393,#6394,#6395,#6396,#6397,#6398,#6399, -#6400,#6401,#6402,#6403,#6404,#6405,#6406,#6407,#6408,#6409,#6410,#6411,#6412, -#6413,#6414,#6415,#6416,#6417,#6418,#6419,#6420,#6421,#6422,#6423,#6424,#6425, -#6426,#6427,#6428,#6429,#6430,#6431,#6432,#6433,#6434,#6435),.UNSPECIFIED.,.F., -.F.,(4,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1, -1,1,1,4),(0.E0,3.392548409266E-2,5.955996456901E-2,8.361137397839E-2, -1.081555982961E-1,1.346489540612E-1,1.641910687550E-1,2.000383494332E-1, -2.345436857876E-1,2.778951082966E-1,3.271565094075E-1,3.825458830477E-1, -4.348298977932E-1,4.825835697265E-1,5.241351068659E-1,5.623989598172E-1, -5.946478452418E-1,6.239452147939E-1,6.509535357706E-1,6.770381017133E-1, -7.052148012084E-1,7.338477991810E-1,7.576239573623E-1,7.805208560009E-1, -7.989547941342E-1,8.161626595409E-1,8.317721007740E-1,8.469816269373E-1, -8.630631457017E-1,8.796204666296E-1,8.948333156101E-1,9.079189984713E-1, -9.198344474191E-1,9.304564974072E-1,9.397651666902E-1,9.480587866902E-1, -9.564390535544E-1,9.657668652110E-1,9.760810158386E-1,9.872889228658E-1,1.E0), -.UNSPECIFIED.); -#6460=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6441,#6442,#6443,#6444,#6445,#6446,#6447, -#6448,#6449,#6450,#6451,#6452,#6453,#6454,#6455,#6456,#6457,#6458,#6459), -.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,4),(0.E0, -5.449694518511E-2,9.693486628817E-2,1.336032132913E-1,1.702749230036E-1, -2.118948954319E-1,2.530249884847E-1,3.023202253882E-1,3.533949149693E-1, -4.122765594469E-1,4.744581273751E-1,5.458393444364E-1,6.246793173534E-1, -7.136712487188E-1,8.060983315365E-1,8.969141469835E-1,1.E0),.UNSPECIFIED.); -#6467=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6461,#6462,#6463,#6464,#6465,#6466), -.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.367125022686E-1,6.632874977327E-1,1.E0), -.UNSPECIFIED.); -#6476=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6472,#6473,#6474,#6475),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6489=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6485,#6486,#6487,#6488),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6498=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6494,#6495,#6496,#6497),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6507=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6503,#6504,#6505,#6506),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6516=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6512,#6513,#6514,#6515),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6525=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6521,#6522,#6523,#6524),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#6534=B_SPLINE_CURVE_WITH_KNOTS('',3,(#6530,#6531,#6532,#6533),.UNSPECIFIED., -.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14847=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14843,#14844,#14845,#14846), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14854=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14848,#14849,#14850,#14851,#14852, -#14853),.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.390786838150E-1, -6.609213161849E-1,1.E0),.UNSPECIFIED.); -#14861=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14855,#14856,#14857,#14858,#14859, -#14860),.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.334642613559E-1, -6.665357386497E-1,1.E0),.UNSPECIFIED.); -#14875=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14862,#14863,#14864,#14865,#14866, -#14867,#14868,#14869,#14870,#14871,#14872,#14873,#14874),.UNSPECIFIED.,.F.,.F.,( -4,1,1,1,1,1,1,1,1,1,4),(0.E0,1.052706058146E-1,2.046623773364E-1, -3.043975717067E-1,4.026733828993E-1,5.004840316358E-1,5.982547988397E-1, -6.963900106079E-1,7.959497445438E-1,8.950977436735E-1,1.E0),.UNSPECIFIED.); -#14902=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14880,#14881,#14882,#14883,#14884, -#14885,#14886,#14887,#14888,#14889,#14890,#14891,#14892,#14893,#14894,#14895, -#14896,#14897,#14898,#14899,#14900,#14901),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1, -1,1,1,1,1,1,1,1,1,1,1,1,4),(0.E0,7.452102549414E-2,1.637067914881E-1, -2.508762869762E-1,3.310475071878E-1,3.980380134526E-1,4.632870319512E-1, -5.162497987040E-1,5.663752923082E-1,6.113661267213E-1,6.510922663256E-1, -6.905656038668E-1,7.358492893007E-1,7.856597008070E-1,8.286974312854E-1, -8.704349301340E-1,9.049072803385E-1,9.365789321279E-1,9.655866536222E-1,1.E0), -.UNSPECIFIED.); -#14909=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14903,#14904,#14905,#14906,#14907, -#14908),.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.352599494522E-1, -6.647400505432E-1,1.E0),.UNSPECIFIED.); -#14918=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14914,#14915,#14916,#14917), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14923=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14919,#14920,#14921,#14922), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14932=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14928,#14929,#14930,#14931), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14945=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14941,#14942,#14943,#14944), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14954=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14950,#14951,#14952,#14953), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14963=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14959,#14960,#14961,#14962), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14968=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14964,#14965,#14966,#14967), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14981=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14977,#14978,#14979,#14980), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14990=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14986,#14987,#14988,#14989), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#14999=B_SPLINE_CURVE_WITH_KNOTS('',3,(#14995,#14996,#14997,#14998), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15008=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15004,#15005,#15006,#15007), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15017=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15013,#15014,#15015,#15016), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15026=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15022,#15023,#15024,#15025), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15035=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15031,#15032,#15033,#15034), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15044=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15040,#15041,#15042,#15043), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15053=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15049,#15050,#15051,#15052), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15060=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15054,#15055,#15056,#15057,#15058, -#15059),.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.345015310528E-1, -6.654984689528E-1,1.E0),.UNSPECIFIED.); -#15069=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15065,#15066,#15067,#15068), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15080=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15074,#15075,#15076,#15077,#15078, -#15079),.UNSPECIFIED.,.F.,.F.,(4,1,1,4),(0.E0,3.367125022686E-1, -6.632874977327E-1,1.E0),.UNSPECIFIED.); -#15100=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15081,#15082,#15083,#15084,#15085, -#15086,#15087,#15088,#15089,#15090,#15091,#15092,#15093,#15094,#15095,#15096, -#15097,#15098,#15099),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,4), -(0.E0,5.449694518511E-2,9.693486628817E-2,1.336032132913E-1,1.702749230036E-1, -2.118948954319E-1,2.530249884847E-1,3.023202253882E-1,3.533949149693E-1, -4.122765594469E-1,4.744581273751E-1,5.458393444364E-1,6.246793173534E-1, -7.136712487188E-1,8.060983315365E-1,8.969141469835E-1,1.E0),.UNSPECIFIED.); -#15148=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15105,#15106,#15107,#15108,#15109, -#15110,#15111,#15112,#15113,#15114,#15115,#15116,#15117,#15118,#15119,#15120, -#15121,#15122,#15123,#15124,#15125,#15126,#15127,#15128,#15129,#15130,#15131, -#15132,#15133,#15134,#15135,#15136,#15137,#15138,#15139,#15140,#15141,#15142, -#15143,#15144,#15145,#15146,#15147),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1, -1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,4),(0.E0, -3.392548409266E-2,5.955996456901E-2,8.361137397839E-2,1.081555982961E-1, -1.346489540612E-1,1.641910687550E-1,2.000383494332E-1,2.345436857876E-1, -2.778951082966E-1,3.271565094075E-1,3.825458830477E-1,4.348298977932E-1, -4.825835697265E-1,5.241351068659E-1,5.623989598172E-1,5.946478452418E-1, -6.239452147939E-1,6.509535357706E-1,6.770381017133E-1,7.052148012084E-1, -7.338477991810E-1,7.576239573623E-1,7.805208560009E-1,7.989547941342E-1, -8.161626595409E-1,8.317721007740E-1,8.469816269373E-1,8.630631457017E-1, -8.796204666296E-1,8.948333156101E-1,9.079189984713E-1,9.198344474191E-1, -9.304564974072E-1,9.397651666902E-1,9.480587866902E-1,9.564390535544E-1, -9.657668652110E-1,9.760810158386E-1,9.872889228658E-1,1.E0),.UNSPECIFIED.); -#15157=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15153,#15154,#15155,#15156), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15166=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15162,#15163,#15164,#15165), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15175=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15171,#15172,#15173,#15174), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15192=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15180,#15181,#15182,#15183,#15184, -#15185,#15186,#15187,#15188,#15189,#15190,#15191),.UNSPECIFIED.,.F.,.F.,(4,1,1, -1,1,1,1,1,1,4),(0.E0,1.174888978136E-1,2.277290966675E-1,3.374615345415E-1, -4.464350365856E-1,5.550456732220E-1,6.638625954523E-1,7.733019360617E-1, -8.831119336622E-1,1.E0),.UNSPECIFIED.); -#15201=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15197,#15198,#15199,#15200), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15214=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15210,#15211,#15212,#15213), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15223=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15219,#15220,#15221,#15222), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15232=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15228,#15229,#15230,#15231), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15241=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15237,#15238,#15239,#15240), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15250=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15246,#15247,#15248,#15249), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15259=B_SPLINE_CURVE_WITH_KNOTS('',3,(#15255,#15256,#15257,#15258), -.UNSPECIFIED.,.F.,.F.,(4,4),(0.E0,1.E0),.UNSPECIFIED.); -#15564=CIRCLE('',#15563,2.5E-1); -#15569=CIRCLE('',#15568,2.5E-1); -#15782=CIRCLE('',#15781,4.E-1); -#15787=CIRCLE('',#15786,4.E-1); -#16028=CIRCLE('',#16027,4.E-1); -#16033=CIRCLE('',#16032,4.E-1); -#16090=CIRCLE('',#16089,4.E-1); -#16095=CIRCLE('',#16094,4.E-1); -#16124=CIRCLE('',#16123,4.E-1); -#16129=CIRCLE('',#16128,4.E-1); -#16190=CIRCLE('',#16189,4.E-1); -#16195=CIRCLE('',#16194,4.E-1); -#16224=CIRCLE('',#16223,4.E-1); -#16229=CIRCLE('',#16228,4.E-1); -#16290=CIRCLE('',#16289,4.E-1); -#16295=CIRCLE('',#16294,4.E-1); -#16324=CIRCLE('',#16323,4.E-1); -#16329=CIRCLE('',#16328,4.E-1); -#16390=CIRCLE('',#16389,4.E-1); -#16395=CIRCLE('',#16394,4.E-1); -#16424=CIRCLE('',#16423,4.E-1); -#16429=CIRCLE('',#16428,4.E-1); -#16490=CIRCLE('',#16489,4.E-1); -#16495=CIRCLE('',#16494,4.E-1); -#16524=CIRCLE('',#16523,4.E-1); -#16529=CIRCLE('',#16528,4.E-1); -#16590=CIRCLE('',#16589,4.E-1); -#16595=CIRCLE('',#16594,4.E-1); -#16624=CIRCLE('',#16623,4.E-1); -#16629=CIRCLE('',#16628,4.E-1); -#16690=CIRCLE('',#16689,4.E-1); -#16695=CIRCLE('',#16694,4.E-1); -#16724=CIRCLE('',#16723,4.E-1); -#16729=CIRCLE('',#16728,4.E-1); -#16778=CIRCLE('',#16777,2.5E-1); -#16783=CIRCLE('',#16782,2.5E-1); -#22141=EDGE_CURVE('',#17498,#17499,#331,.T.); -#22143=EDGE_CURVE('',#17501,#17499,#335,.T.); -#22145=EDGE_CURVE('',#17501,#17511,#339,.T.); -#22147=EDGE_CURVE('',#17511,#17506,#343,.T.); -#22149=EDGE_CURVE('',#17506,#17507,#347,.T.); -#22151=EDGE_CURVE('',#17509,#17507,#351,.T.); -#22153=EDGE_CURVE('',#17509,#17519,#355,.T.); -#22155=EDGE_CURVE('',#17519,#17514,#359,.T.); -#22157=EDGE_CURVE('',#17514,#17515,#363,.T.); -#22159=EDGE_CURVE('',#17517,#17515,#367,.T.); -#22161=EDGE_CURVE('',#17517,#16798,#371,.T.); -#22163=EDGE_CURVE('',#16798,#16799,#375,.T.); -#22165=EDGE_CURVE('',#16799,#17191,#379,.T.); -#22167=EDGE_CURVE('',#17189,#17191,#383,.T.); -#22169=EDGE_CURVE('',#17187,#17189,#387,.T.); -#22171=EDGE_CURVE('',#17186,#17187,#391,.T.); -#22173=EDGE_CURVE('',#17186,#17159,#395,.T.); -#22175=EDGE_CURVE('',#17157,#17159,#399,.T.); -#22177=EDGE_CURVE('',#17155,#17157,#403,.T.); -#22179=EDGE_CURVE('',#17154,#17155,#407,.T.); -#22181=EDGE_CURVE('',#17154,#17127,#411,.T.); -#22183=EDGE_CURVE('',#17125,#17127,#415,.T.); -#22185=EDGE_CURVE('',#17123,#17125,#419,.T.); -#22187=EDGE_CURVE('',#17122,#17123,#423,.T.); -#22189=EDGE_CURVE('',#17122,#17095,#427,.T.); -#22191=EDGE_CURVE('',#17093,#17095,#431,.T.); -#22193=EDGE_CURVE('',#17091,#17093,#435,.T.); -#22195=EDGE_CURVE('',#17090,#17091,#439,.T.); -#22197=EDGE_CURVE('',#17090,#17063,#443,.T.); -#22199=EDGE_CURVE('',#17061,#17063,#447,.T.); -#22201=EDGE_CURVE('',#17059,#17061,#451,.T.); -#22203=EDGE_CURVE('',#17058,#17059,#455,.T.); -#22205=EDGE_CURVE('',#17058,#17031,#459,.T.); -#22207=EDGE_CURVE('',#17029,#17031,#463,.T.); -#22209=EDGE_CURVE('',#17027,#17029,#467,.T.); -#22211=EDGE_CURVE('',#17026,#17027,#471,.T.); -#22213=EDGE_CURVE('',#17026,#16999,#475,.T.); -#22215=EDGE_CURVE('',#16997,#16999,#479,.T.); -#22217=EDGE_CURVE('',#16995,#16997,#483,.T.); -#22219=EDGE_CURVE('',#16994,#16995,#487,.T.); -#22221=EDGE_CURVE('',#16994,#16967,#491,.T.); -#22223=EDGE_CURVE('',#16965,#16967,#495,.T.); -#22225=EDGE_CURVE('',#16963,#16965,#499,.T.); -#22227=EDGE_CURVE('',#16962,#16963,#503,.T.); -#22229=EDGE_CURVE('',#16962,#16802,#507,.T.); -#22231=EDGE_CURVE('',#16802,#16803,#511,.T.); -#22233=EDGE_CURVE('',#16803,#16975,#515,.T.); -#22235=EDGE_CURVE('',#16975,#16973,#519,.T.); -#22237=EDGE_CURVE('',#16971,#16973,#523,.T.); -#22239=EDGE_CURVE('',#16970,#16971,#527,.T.); -#22241=EDGE_CURVE('',#16970,#17007,#531,.T.); -#22243=EDGE_CURVE('',#17007,#17005,#535,.T.); -#22245=EDGE_CURVE('',#17003,#17005,#539,.T.); -#22247=EDGE_CURVE('',#17002,#17003,#543,.T.); -#22249=EDGE_CURVE('',#17002,#17039,#547,.T.); -#22251=EDGE_CURVE('',#17039,#17037,#551,.T.); -#22253=EDGE_CURVE('',#17035,#17037,#555,.T.); -#22255=EDGE_CURVE('',#17034,#17035,#559,.T.); -#22257=EDGE_CURVE('',#17034,#17071,#563,.T.); -#22259=EDGE_CURVE('',#17071,#17069,#567,.T.); -#22261=EDGE_CURVE('',#17067,#17069,#571,.T.); -#22263=EDGE_CURVE('',#17066,#17067,#575,.T.); -#22265=EDGE_CURVE('',#17066,#17103,#579,.T.); -#22267=EDGE_CURVE('',#17103,#17101,#583,.T.); -#22269=EDGE_CURVE('',#17099,#17101,#587,.T.); -#22271=EDGE_CURVE('',#17098,#17099,#591,.T.); -#22273=EDGE_CURVE('',#17098,#17135,#595,.T.); -#22275=EDGE_CURVE('',#17135,#17133,#599,.T.); -#22277=EDGE_CURVE('',#17131,#17133,#603,.T.); -#22279=EDGE_CURVE('',#17130,#17131,#607,.T.); -#22281=EDGE_CURVE('',#17130,#17167,#611,.T.); -#22283=EDGE_CURVE('',#17167,#17165,#615,.T.); -#22285=EDGE_CURVE('',#17163,#17165,#619,.T.); -#22287=EDGE_CURVE('',#17162,#17163,#623,.T.); -#22289=EDGE_CURVE('',#17162,#17199,#627,.T.); -#22291=EDGE_CURVE('',#17199,#17197,#631,.T.); -#22293=EDGE_CURVE('',#17195,#17197,#635,.T.); -#22295=EDGE_CURVE('',#17194,#17195,#639,.T.); -#22297=EDGE_CURVE('',#17194,#16806,#643,.T.); -#22299=EDGE_CURVE('',#16806,#16807,#647,.T.); -#22301=EDGE_CURVE('',#16807,#17503,#651,.T.); -#22303=EDGE_CURVE('',#17503,#17498,#655,.T.); -#22307=EDGE_CURVE('',#18406,#18407,#38,.T.); -#22309=EDGE_CURVE('',#18407,#18406,#43,.T.); -#22313=EDGE_CURVE('',#18410,#18411,#48,.T.); -#22315=EDGE_CURVE('',#18411,#18410,#53,.T.); -#22319=EDGE_CURVE('',#18414,#18415,#58,.T.); -#22321=EDGE_CURVE('',#18415,#18414,#63,.T.); -#22325=EDGE_CURVE('',#18434,#18435,#68,.T.); -#22327=EDGE_CURVE('',#18435,#18434,#73,.T.); -#22331=EDGE_CURVE('',#18438,#18439,#78,.T.); -#22333=EDGE_CURVE('',#18439,#18438,#83,.T.); -#22337=EDGE_CURVE('',#18442,#18443,#88,.T.); -#22339=EDGE_CURVE('',#18443,#18442,#93,.T.); -#22343=EDGE_CURVE('',#18446,#18447,#98,.T.); -#22345=EDGE_CURVE('',#18447,#18446,#103,.T.); -#22349=EDGE_CURVE('',#18466,#18467,#108,.T.); -#22351=EDGE_CURVE('',#18467,#18466,#113,.T.); -#22355=EDGE_CURVE('',#18470,#18471,#118,.T.); -#22357=EDGE_CURVE('',#18471,#18470,#123,.T.); -#22361=EDGE_CURVE('',#18474,#18475,#128,.T.); -#22363=EDGE_CURVE('',#18475,#18474,#133,.T.); -#22367=EDGE_CURVE('',#18478,#18479,#138,.T.); -#22369=EDGE_CURVE('',#18479,#18478,#143,.T.); -#22373=EDGE_CURVE('',#18498,#18499,#148,.T.); -#22375=EDGE_CURVE('',#18499,#18498,#153,.T.); -#22379=EDGE_CURVE('',#18502,#18503,#158,.T.); -#22381=EDGE_CURVE('',#18503,#18502,#163,.T.); -#22385=EDGE_CURVE('',#18506,#18507,#168,.T.); -#22387=EDGE_CURVE('',#18507,#18506,#173,.T.); -#22391=EDGE_CURVE('',#18510,#18511,#178,.T.); -#22393=EDGE_CURVE('',#18511,#18510,#183,.T.); -#22397=EDGE_CURVE('',#18530,#18531,#188,.T.); -#22399=EDGE_CURVE('',#18531,#18530,#193,.T.); -#22403=EDGE_CURVE('',#18534,#18535,#198,.T.); -#22405=EDGE_CURVE('',#18535,#18534,#203,.T.); -#22409=EDGE_CURVE('',#18538,#18539,#208,.T.); -#22411=EDGE_CURVE('',#18539,#18538,#213,.T.); -#22415=EDGE_CURVE('',#18542,#18543,#218,.T.); -#22417=EDGE_CURVE('',#18543,#18542,#223,.T.); -#22421=EDGE_CURVE('',#18562,#18563,#228,.T.); -#22423=EDGE_CURVE('',#18563,#18562,#233,.T.); -#22427=EDGE_CURVE('',#18566,#18567,#238,.T.); -#22429=EDGE_CURVE('',#18567,#18566,#243,.T.); -#22433=EDGE_CURVE('',#18570,#18571,#248,.T.); -#22435=EDGE_CURVE('',#18571,#18570,#253,.T.); -#22439=EDGE_CURVE('',#18574,#18575,#258,.T.); -#22441=EDGE_CURVE('',#18575,#18574,#263,.T.); -#22445=EDGE_CURVE('',#18610,#18611,#267,.T.); -#22447=EDGE_CURVE('',#18611,#18613,#271,.T.); -#22449=EDGE_CURVE('',#18613,#18615,#275,.T.); -#22451=EDGE_CURVE('',#18615,#18610,#279,.T.); -#22455=EDGE_CURVE('',#18618,#18619,#283,.T.); -#22457=EDGE_CURVE('',#18619,#18621,#287,.T.); -#22459=EDGE_CURVE('',#18621,#18623,#291,.T.); -#22461=EDGE_CURVE('',#18623,#18618,#295,.T.); -#22465=EDGE_CURVE('',#18626,#18627,#299,.T.); -#22467=EDGE_CURVE('',#18627,#18629,#303,.T.); -#22469=EDGE_CURVE('',#18629,#18631,#307,.T.); -#22471=EDGE_CURVE('',#18631,#18626,#311,.T.); -#22475=EDGE_CURVE('',#18634,#18635,#315,.T.); -#22477=EDGE_CURVE('',#18635,#18637,#319,.T.); -#22479=EDGE_CURVE('',#18637,#18639,#323,.T.); -#22481=EDGE_CURVE('',#18639,#18634,#327,.T.); -#22485=EDGE_CURVE('',#18402,#18403,#28,.T.); -#22487=EDGE_CURVE('',#18403,#18402,#33,.T.); -#22491=ADVANCED_FACE('',(#22306,#22312,#22318,#22324,#22330,#22336,#22342, -#22348,#22354,#22360,#22366,#22372,#22378,#22384,#22390,#22396,#22402,#22408, -#22414,#22420,#22426,#22432,#22438,#22444,#22454,#22464,#22474,#22484,#22490), -#22140,.F.); -#22505=EDGE_CURVE('',#18402,#18387,#659,.T.); -#22507=EDGE_CURVE('',#18386,#18387,#668,.T.); -#22509=EDGE_CURVE('',#18403,#18386,#663,.T.); -#22513=ADVANCED_FACE('',(#22512),#22503,.F.); -#22521=EDGE_CURVE('',#18387,#18386,#673,.T.); -#22526=ADVANCED_FACE('',(#22525),#22518,.F.); -#22536=ADVANCED_FACE('',(#22535),#22531,.T.); -#22549=EDGE_CURVE('',#18390,#18391,#678,.T.); -#22551=EDGE_CURVE('',#18391,#18390,#683,.T.); -#22555=ADVANCED_FACE('',(#22554),#22548,.T.); -#22568=EDGE_CURVE('',#18394,#18395,#688,.T.); -#22570=EDGE_CURVE('',#18395,#18394,#693,.T.); -#22574=ADVANCED_FACE('',(#22573),#22567,.T.); -#22587=EDGE_CURVE('',#18398,#18399,#698,.T.); -#22589=EDGE_CURVE('',#18399,#18398,#703,.T.); -#22593=ADVANCED_FACE('',(#22592),#22586,.T.); -#22607=EDGE_CURVE('',#18406,#18391,#707,.T.); -#22610=EDGE_CURVE('',#18407,#18390,#711,.T.); -#22614=ADVANCED_FACE('',(#22613),#22605,.F.); -#22626=ADVANCED_FACE('',(#22625),#22619,.F.); -#22633=EDGE_CURVE('',#18410,#18395,#715,.T.); -#22636=EDGE_CURVE('',#18411,#18394,#719,.T.); -#22640=ADVANCED_FACE('',(#22639),#22631,.F.); -#22652=ADVANCED_FACE('',(#22651),#22645,.F.); -#22659=EDGE_CURVE('',#18414,#18399,#723,.T.); -#22662=EDGE_CURVE('',#18415,#18398,#727,.T.); -#22666=ADVANCED_FACE('',(#22665),#22657,.F.); -#22678=ADVANCED_FACE('',(#22677),#22671,.F.); -#22685=EDGE_CURVE('',#18434,#18418,#731,.T.); -#22687=EDGE_CURVE('',#18418,#18419,#740,.T.); -#22689=EDGE_CURVE('',#18435,#18419,#735,.T.); -#22693=ADVANCED_FACE('',(#22692),#22683,.F.); -#22701=EDGE_CURVE('',#18419,#18418,#745,.T.); -#22706=ADVANCED_FACE('',(#22705),#22698,.F.); -#22716=ADVANCED_FACE('',(#22715),#22711,.T.); -#22729=EDGE_CURVE('',#18422,#18423,#750,.T.); -#22731=EDGE_CURVE('',#18423,#18422,#755,.T.); -#22735=ADVANCED_FACE('',(#22734),#22728,.T.); -#22748=EDGE_CURVE('',#18426,#18427,#760,.T.); -#22750=EDGE_CURVE('',#18427,#18426,#765,.T.); -#22754=ADVANCED_FACE('',(#22753),#22747,.T.); -#22767=EDGE_CURVE('',#18430,#18431,#770,.T.); -#22769=EDGE_CURVE('',#18431,#18430,#775,.T.); -#22773=ADVANCED_FACE('',(#22772),#22766,.T.); -#22787=EDGE_CURVE('',#18438,#18422,#779,.T.); -#22790=EDGE_CURVE('',#18439,#18423,#783,.T.); -#22794=ADVANCED_FACE('',(#22793),#22785,.F.); -#22806=ADVANCED_FACE('',(#22805),#22799,.F.); -#22813=EDGE_CURVE('',#18442,#18426,#787,.T.); -#22816=EDGE_CURVE('',#18443,#18427,#791,.T.); -#22820=ADVANCED_FACE('',(#22819),#22811,.F.); -#22832=ADVANCED_FACE('',(#22831),#22825,.F.); -#22839=EDGE_CURVE('',#18446,#18430,#795,.T.); -#22842=EDGE_CURVE('',#18447,#18431,#799,.T.); -#22846=ADVANCED_FACE('',(#22845),#22837,.F.); -#22858=ADVANCED_FACE('',(#22857),#22851,.F.); -#22865=EDGE_CURVE('',#18466,#18450,#803,.T.); -#22867=EDGE_CURVE('',#18450,#18451,#812,.T.); -#22869=EDGE_CURVE('',#18467,#18451,#807,.T.); -#22873=ADVANCED_FACE('',(#22872),#22863,.F.); -#22881=EDGE_CURVE('',#18451,#18450,#817,.T.); -#22886=ADVANCED_FACE('',(#22885),#22878,.F.); -#22896=ADVANCED_FACE('',(#22895),#22891,.T.); -#22909=EDGE_CURVE('',#18454,#18455,#822,.T.); -#22911=EDGE_CURVE('',#18455,#18454,#827,.T.); -#22915=ADVANCED_FACE('',(#22914),#22908,.T.); -#22928=EDGE_CURVE('',#18458,#18459,#832,.T.); -#22930=EDGE_CURVE('',#18459,#18458,#837,.T.); -#22934=ADVANCED_FACE('',(#22933),#22927,.T.); -#22947=EDGE_CURVE('',#18462,#18463,#842,.T.); -#22949=EDGE_CURVE('',#18463,#18462,#847,.T.); -#22953=ADVANCED_FACE('',(#22952),#22946,.T.); -#22967=EDGE_CURVE('',#18470,#18454,#851,.T.); -#22970=EDGE_CURVE('',#18471,#18455,#855,.T.); -#22974=ADVANCED_FACE('',(#22973),#22965,.F.); -#22986=ADVANCED_FACE('',(#22985),#22979,.F.); -#22993=EDGE_CURVE('',#18474,#18458,#859,.T.); -#22996=EDGE_CURVE('',#18475,#18459,#863,.T.); -#23000=ADVANCED_FACE('',(#22999),#22991,.F.); -#23012=ADVANCED_FACE('',(#23011),#23005,.F.); -#23019=EDGE_CURVE('',#18478,#18462,#867,.T.); -#23022=EDGE_CURVE('',#18479,#18463,#871,.T.); -#23026=ADVANCED_FACE('',(#23025),#23017,.F.); -#23038=ADVANCED_FACE('',(#23037),#23031,.F.); -#23045=EDGE_CURVE('',#18498,#18482,#875,.T.); -#23047=EDGE_CURVE('',#18482,#18483,#884,.T.); -#23049=EDGE_CURVE('',#18499,#18483,#879,.T.); -#23053=ADVANCED_FACE('',(#23052),#23043,.F.); -#23061=EDGE_CURVE('',#18483,#18482,#889,.T.); -#23066=ADVANCED_FACE('',(#23065),#23058,.F.); -#23076=ADVANCED_FACE('',(#23075),#23071,.T.); -#23089=EDGE_CURVE('',#18486,#18487,#894,.T.); -#23091=EDGE_CURVE('',#18487,#18486,#899,.T.); -#23095=ADVANCED_FACE('',(#23094),#23088,.T.); -#23108=EDGE_CURVE('',#18490,#18491,#904,.T.); -#23110=EDGE_CURVE('',#18491,#18490,#909,.T.); -#23114=ADVANCED_FACE('',(#23113),#23107,.T.); -#23127=EDGE_CURVE('',#18494,#18495,#914,.T.); -#23129=EDGE_CURVE('',#18495,#18494,#919,.T.); -#23133=ADVANCED_FACE('',(#23132),#23126,.T.); -#23147=EDGE_CURVE('',#18502,#18486,#923,.T.); -#23150=EDGE_CURVE('',#18503,#18487,#927,.T.); -#23154=ADVANCED_FACE('',(#23153),#23145,.F.); -#23166=ADVANCED_FACE('',(#23165),#23159,.F.); -#23173=EDGE_CURVE('',#18506,#18490,#931,.T.); -#23176=EDGE_CURVE('',#18507,#18491,#935,.T.); -#23180=ADVANCED_FACE('',(#23179),#23171,.F.); -#23192=ADVANCED_FACE('',(#23191),#23185,.F.); -#23199=EDGE_CURVE('',#18510,#18494,#939,.T.); -#23202=EDGE_CURVE('',#18511,#18495,#943,.T.); -#23206=ADVANCED_FACE('',(#23205),#23197,.F.); -#23218=ADVANCED_FACE('',(#23217),#23211,.F.); -#23225=EDGE_CURVE('',#18530,#18514,#947,.T.); -#23227=EDGE_CURVE('',#18514,#18515,#956,.T.); -#23229=EDGE_CURVE('',#18531,#18515,#951,.T.); -#23233=ADVANCED_FACE('',(#23232),#23223,.F.); -#23241=EDGE_CURVE('',#18515,#18514,#961,.T.); -#23246=ADVANCED_FACE('',(#23245),#23238,.F.); -#23256=ADVANCED_FACE('',(#23255),#23251,.T.); -#23269=EDGE_CURVE('',#18518,#18519,#966,.T.); -#23271=EDGE_CURVE('',#18519,#18518,#971,.T.); -#23275=ADVANCED_FACE('',(#23274),#23268,.T.); -#23288=EDGE_CURVE('',#18522,#18523,#976,.T.); -#23290=EDGE_CURVE('',#18523,#18522,#981,.T.); -#23294=ADVANCED_FACE('',(#23293),#23287,.T.); -#23307=EDGE_CURVE('',#18526,#18527,#986,.T.); -#23309=EDGE_CURVE('',#18527,#18526,#991,.T.); -#23313=ADVANCED_FACE('',(#23312),#23306,.T.); -#23327=EDGE_CURVE('',#18534,#18518,#995,.T.); -#23330=EDGE_CURVE('',#18535,#18519,#999,.T.); -#23334=ADVANCED_FACE('',(#23333),#23325,.F.); -#23346=ADVANCED_FACE('',(#23345),#23339,.F.); -#23353=EDGE_CURVE('',#18538,#18522,#1003,.T.); -#23356=EDGE_CURVE('',#18539,#18523,#1007,.T.); -#23360=ADVANCED_FACE('',(#23359),#23351,.F.); -#23372=ADVANCED_FACE('',(#23371),#23365,.F.); -#23379=EDGE_CURVE('',#18542,#18526,#1011,.T.); -#23382=EDGE_CURVE('',#18543,#18527,#1015,.T.); -#23386=ADVANCED_FACE('',(#23385),#23377,.F.); -#23398=ADVANCED_FACE('',(#23397),#23391,.F.); -#23405=EDGE_CURVE('',#18562,#18546,#1019,.T.); -#23407=EDGE_CURVE('',#18546,#18547,#1028,.T.); -#23409=EDGE_CURVE('',#18563,#18547,#1023,.T.); -#23413=ADVANCED_FACE('',(#23412),#23403,.F.); -#23421=EDGE_CURVE('',#18547,#18546,#1033,.T.); -#23426=ADVANCED_FACE('',(#23425),#23418,.F.); -#23436=ADVANCED_FACE('',(#23435),#23431,.T.); -#23449=EDGE_CURVE('',#18550,#18551,#1038,.T.); -#23451=EDGE_CURVE('',#18551,#18550,#1043,.T.); -#23455=ADVANCED_FACE('',(#23454),#23448,.T.); -#23468=EDGE_CURVE('',#18554,#18555,#1048,.T.); -#23470=EDGE_CURVE('',#18555,#18554,#1053,.T.); -#23474=ADVANCED_FACE('',(#23473),#23467,.T.); -#23487=EDGE_CURVE('',#18558,#18559,#1058,.T.); -#23489=EDGE_CURVE('',#18559,#18558,#1063,.T.); -#23493=ADVANCED_FACE('',(#23492),#23486,.T.); -#23507=EDGE_CURVE('',#18566,#18550,#1067,.T.); -#23510=EDGE_CURVE('',#18567,#18551,#1071,.T.); -#23514=ADVANCED_FACE('',(#23513),#23505,.F.); -#23526=ADVANCED_FACE('',(#23525),#23519,.F.); -#23533=EDGE_CURVE('',#18570,#18554,#1075,.T.); -#23536=EDGE_CURVE('',#18571,#18555,#1079,.T.); -#23540=ADVANCED_FACE('',(#23539),#23531,.F.); -#23552=ADVANCED_FACE('',(#23551),#23545,.F.); -#23559=EDGE_CURVE('',#18574,#18558,#1083,.T.); -#23562=EDGE_CURVE('',#18575,#18559,#1087,.T.); -#23566=ADVANCED_FACE('',(#23565),#23557,.F.); -#23578=ADVANCED_FACE('',(#23577),#23571,.F.); -#23585=EDGE_CURVE('',#18610,#18578,#1091,.T.); -#23587=EDGE_CURVE('',#18578,#18579,#1107,.T.); -#23589=EDGE_CURVE('',#18611,#18579,#1103,.T.); -#23593=ADVANCED_FACE('',(#23592),#23583,.F.); -#23600=EDGE_CURVE('',#18615,#18583,#1095,.T.); -#23602=EDGE_CURVE('',#18583,#18578,#1111,.T.); -#23607=ADVANCED_FACE('',(#23606),#23598,.F.); -#23614=EDGE_CURVE('',#18613,#18581,#1099,.T.); -#23616=EDGE_CURVE('',#18581,#18583,#1115,.T.); -#23621=ADVANCED_FACE('',(#23620),#23612,.F.); -#23629=EDGE_CURVE('',#18579,#18581,#1119,.T.); -#23634=ADVANCED_FACE('',(#23633),#23626,.F.); -#23646=ADVANCED_FACE('',(#23645),#23639,.T.); -#23659=EDGE_CURVE('',#18586,#18587,#1123,.T.); -#23661=EDGE_CURVE('',#18591,#18586,#1127,.T.); -#23663=EDGE_CURVE('',#18589,#18591,#1131,.T.); -#23665=EDGE_CURVE('',#18587,#18589,#1135,.T.); -#23669=ADVANCED_FACE('',(#23668),#23658,.T.); -#23682=EDGE_CURVE('',#18594,#18595,#1139,.T.); -#23684=EDGE_CURVE('',#18599,#18594,#1143,.T.); -#23686=EDGE_CURVE('',#18597,#18599,#1147,.T.); -#23688=EDGE_CURVE('',#18595,#18597,#1151,.T.); -#23692=ADVANCED_FACE('',(#23691),#23681,.T.); -#23705=EDGE_CURVE('',#18602,#18603,#1155,.T.); -#23707=EDGE_CURVE('',#18607,#18602,#1159,.T.); -#23709=EDGE_CURVE('',#18605,#18607,#1163,.T.); -#23711=EDGE_CURVE('',#18603,#18605,#1167,.T.); -#23715=ADVANCED_FACE('',(#23714),#23704,.T.); -#23729=EDGE_CURVE('',#18618,#18586,#1171,.T.); -#23732=EDGE_CURVE('',#18619,#18587,#1183,.T.); -#23736=ADVANCED_FACE('',(#23735),#23727,.F.); -#23743=EDGE_CURVE('',#18623,#18591,#1175,.T.); -#23749=ADVANCED_FACE('',(#23748),#23741,.F.); -#23756=EDGE_CURVE('',#18621,#18589,#1179,.T.); -#23762=ADVANCED_FACE('',(#23761),#23754,.F.); -#23774=ADVANCED_FACE('',(#23773),#23767,.F.); -#23781=EDGE_CURVE('',#18626,#18594,#1187,.T.); -#23784=EDGE_CURVE('',#18627,#18595,#1199,.T.); -#23788=ADVANCED_FACE('',(#23787),#23779,.F.); -#23795=EDGE_CURVE('',#18631,#18599,#1191,.T.); -#23801=ADVANCED_FACE('',(#23800),#23793,.F.); -#23808=EDGE_CURVE('',#18629,#18597,#1195,.T.); -#23814=ADVANCED_FACE('',(#23813),#23806,.F.); -#23826=ADVANCED_FACE('',(#23825),#23819,.F.); -#23833=EDGE_CURVE('',#18634,#18602,#1203,.T.); -#23836=EDGE_CURVE('',#18635,#18603,#1215,.T.); -#23840=ADVANCED_FACE('',(#23839),#23831,.F.); -#23847=EDGE_CURVE('',#18639,#18607,#1207,.T.); -#23853=ADVANCED_FACE('',(#23852),#23845,.F.); -#23860=EDGE_CURVE('',#18637,#18605,#1211,.T.); -#23866=ADVANCED_FACE('',(#23865),#23858,.F.); -#23878=ADVANCED_FACE('',(#23877),#23871,.F.); -#23885=EDGE_CURVE('',#17498,#17486,#1219,.T.); -#23887=EDGE_CURVE('',#17486,#17487,#1327,.T.); -#23889=EDGE_CURVE('',#17499,#17487,#16795,.T.); -#23893=ADVANCED_FACE('',(#23892),#23883,.F.); -#23900=EDGE_CURVE('',#17503,#17543,#1287,.T.); -#23902=EDGE_CURVE('',#17543,#17486,#1331,.T.); -#23907=ADVANCED_FACE('',(#23906),#23898,.F.); -#23913=EDGE_CURVE('',#17522,#17523,#1223,.T.); -#23915=EDGE_CURVE('',#17523,#17483,#1227,.T.); -#23917=EDGE_CURVE('',#17483,#16810,#1769,.T.); -#23919=EDGE_CURVE('',#16798,#16810,#16069,.T.); -#23922=EDGE_CURVE('',#17517,#17522,#1231,.T.); -#23926=ADVANCED_FACE('',(#23925),#23912,.T.); -#23932=EDGE_CURVE('',#17526,#17527,#1235,.T.); -#23934=EDGE_CURVE('',#17519,#17527,#1239,.T.); -#23937=EDGE_CURVE('',#17509,#17530,#1243,.T.); -#23939=EDGE_CURVE('',#17530,#17531,#1247,.T.); -#23941=EDGE_CURVE('',#17531,#17480,#1251,.T.); -#23943=EDGE_CURVE('',#17480,#17481,#1773,.T.); -#23945=EDGE_CURVE('',#17526,#17481,#1255,.T.); -#23949=ADVANCED_FACE('',(#23948),#23931,.T.); -#23955=EDGE_CURVE('',#17534,#17535,#1259,.T.); -#23957=EDGE_CURVE('',#17511,#17535,#1263,.T.); -#23960=EDGE_CURVE('',#17501,#17538,#1267,.T.); -#23962=EDGE_CURVE('',#17538,#17539,#1271,.T.); -#23964=EDGE_CURVE('',#17539,#17476,#1275,.T.); -#23966=EDGE_CURVE('',#17476,#17477,#1777,.T.); -#23968=EDGE_CURVE('',#17534,#17477,#1279,.T.); -#23972=ADVANCED_FACE('',(#23971),#23954,.T.); -#23978=EDGE_CURVE('',#17542,#17543,#1283,.T.); -#23982=EDGE_CURVE('',#16807,#16819,#1291,.T.); -#23984=EDGE_CURVE('',#16819,#17473,#1489,.T.); -#23986=EDGE_CURVE('',#17542,#17473,#1295,.T.); -#23990=ADVANCED_FACE('',(#23989),#23977,.T.); -#23997=EDGE_CURVE('',#17495,#17522,#1299,.T.); -#23999=EDGE_CURVE('',#17494,#17495,#1303,.T.); -#24001=EDGE_CURVE('',#17527,#17494,#1307,.T.); -#24004=EDGE_CURVE('',#17523,#17526,#1344,.T.); -#24008=ADVANCED_FACE('',(#24007),#23995,.T.); -#24022=EDGE_CURVE('',#17491,#17530,#1311,.T.); -#24024=EDGE_CURVE('',#17490,#17491,#1315,.T.); -#24026=EDGE_CURVE('',#17535,#17490,#1319,.T.); -#24029=EDGE_CURVE('',#17531,#17534,#16778,.T.); -#24033=ADVANCED_FACE('',(#24032),#24020,.T.); -#24047=EDGE_CURVE('',#17487,#17538,#1323,.T.); -#24052=EDGE_CURVE('',#17539,#17542,#15564,.T.); -#24056=ADVANCED_FACE('',(#24055),#24045,.T.); -#24070=EDGE_CURVE('',#17515,#17495,#1335,.T.); -#24076=ADVANCED_FACE('',(#24075),#24068,.F.); -#24083=EDGE_CURVE('',#17514,#17494,#1339,.T.); -#24089=ADVANCED_FACE('',(#24088),#24081,.F.); -#24101=ADVANCED_FACE('',(#24100),#24094,.F.); -#24109=EDGE_CURVE('',#17481,#17483,#1349,.T.); -#24114=ADVANCED_FACE('',(#24113),#24106,.F.); -#24127=EDGE_CURVE('',#17473,#17476,#15569,.T.); -#24130=EDGE_CURVE('',#16818,#16819,#1493,.T.); -#24132=EDGE_CURVE('',#17210,#16818,#1497,.T.); -#24134=EDGE_CURVE('',#17210,#17211,#1501,.T.); -#24136=EDGE_CURVE('',#17211,#17213,#1505,.T.); -#24138=EDGE_CURVE('',#17215,#17213,#1509,.T.); -#24140=EDGE_CURVE('',#17178,#17215,#1513,.T.); -#24142=EDGE_CURVE('',#17178,#17179,#1517,.T.); -#24144=EDGE_CURVE('',#17179,#17181,#1521,.T.); -#24146=EDGE_CURVE('',#17183,#17181,#1525,.T.); -#24148=EDGE_CURVE('',#17146,#17183,#1529,.T.); -#24150=EDGE_CURVE('',#17146,#17147,#1533,.T.); -#24152=EDGE_CURVE('',#17147,#17149,#1537,.T.); -#24154=EDGE_CURVE('',#17151,#17149,#1541,.T.); -#24156=EDGE_CURVE('',#17114,#17151,#1545,.T.); -#24158=EDGE_CURVE('',#17114,#17115,#1549,.T.); -#24160=EDGE_CURVE('',#17115,#17117,#1553,.T.); -#24162=EDGE_CURVE('',#17119,#17117,#1557,.T.); -#24164=EDGE_CURVE('',#17082,#17119,#1561,.T.); -#24166=EDGE_CURVE('',#17082,#17083,#1565,.T.); -#24168=EDGE_CURVE('',#17083,#17085,#1569,.T.); -#24170=EDGE_CURVE('',#17087,#17085,#1573,.T.); -#24172=EDGE_CURVE('',#17050,#17087,#1577,.T.); -#24174=EDGE_CURVE('',#17050,#17051,#1581,.T.); -#24176=EDGE_CURVE('',#17051,#17053,#1585,.T.); -#24178=EDGE_CURVE('',#17055,#17053,#1589,.T.); -#24180=EDGE_CURVE('',#17018,#17055,#1593,.T.); -#24182=EDGE_CURVE('',#17018,#17019,#1597,.T.); -#24184=EDGE_CURVE('',#17019,#17021,#1601,.T.); -#24186=EDGE_CURVE('',#17023,#17021,#1605,.T.); -#24188=EDGE_CURVE('',#16986,#17023,#1609,.T.); -#24190=EDGE_CURVE('',#16986,#16987,#1613,.T.); -#24192=EDGE_CURVE('',#16987,#16991,#1617,.T.); -#24194=EDGE_CURVE('',#16990,#16991,#1621,.T.); -#24196=EDGE_CURVE('',#16815,#16990,#1625,.T.); -#24198=EDGE_CURVE('',#16814,#16815,#1629,.T.); -#24200=EDGE_CURVE('',#16978,#16814,#1633,.T.); -#24202=EDGE_CURVE('',#16978,#16979,#1637,.T.); -#24204=EDGE_CURVE('',#16979,#16981,#1641,.T.); -#24206=EDGE_CURVE('',#16981,#16983,#1645,.T.); -#24208=EDGE_CURVE('',#17010,#16983,#1649,.T.); -#24210=EDGE_CURVE('',#17010,#17011,#1653,.T.); -#24212=EDGE_CURVE('',#17011,#17013,#1657,.T.); -#24214=EDGE_CURVE('',#17013,#17015,#1661,.T.); -#24216=EDGE_CURVE('',#17042,#17015,#1665,.T.); -#24218=EDGE_CURVE('',#17042,#17043,#1669,.T.); -#24220=EDGE_CURVE('',#17043,#17045,#1673,.T.); -#24222=EDGE_CURVE('',#17045,#17047,#1677,.T.); -#24224=EDGE_CURVE('',#17074,#17047,#1681,.T.); -#24226=EDGE_CURVE('',#17074,#17075,#1685,.T.); -#24228=EDGE_CURVE('',#17075,#17077,#1689,.T.); -#24230=EDGE_CURVE('',#17077,#17079,#1693,.T.); -#24232=EDGE_CURVE('',#17106,#17079,#1697,.T.); -#24234=EDGE_CURVE('',#17106,#17107,#1701,.T.); -#24236=EDGE_CURVE('',#17107,#17109,#1705,.T.); -#24238=EDGE_CURVE('',#17109,#17111,#1709,.T.); -#24240=EDGE_CURVE('',#17138,#17111,#1713,.T.); -#24242=EDGE_CURVE('',#17138,#17139,#1717,.T.); -#24244=EDGE_CURVE('',#17139,#17141,#1721,.T.); -#24246=EDGE_CURVE('',#17141,#17143,#1725,.T.); -#24248=EDGE_CURVE('',#17170,#17143,#1729,.T.); -#24250=EDGE_CURVE('',#17170,#17171,#1733,.T.); -#24252=EDGE_CURVE('',#17171,#17173,#1737,.T.); -#24254=EDGE_CURVE('',#17173,#17175,#1741,.T.); -#24256=EDGE_CURVE('',#17202,#17175,#1745,.T.); -#24258=EDGE_CURVE('',#17202,#17203,#1749,.T.); -#24260=EDGE_CURVE('',#17203,#17205,#1753,.T.); -#24262=EDGE_CURVE('',#17205,#17207,#1757,.T.); -#24264=EDGE_CURVE('',#16811,#17207,#1761,.T.); -#24266=EDGE_CURVE('',#16810,#16811,#1765,.T.); -#24271=EDGE_CURVE('',#17477,#17480,#16783,.T.); -#24276=EDGE_CURVE('',#16941,#16943,#1377,.T.); -#24278=EDGE_CURVE('',#16873,#16943,#1381,.T.); -#24280=EDGE_CURVE('',#16872,#16873,#1385,.T.); -#24282=EDGE_CURVE('',#16941,#16872,#1389,.T.); -#24286=EDGE_CURVE('',#16945,#16947,#1393,.T.); -#24288=EDGE_CURVE('',#16841,#16947,#1397,.T.); -#24290=EDGE_CURVE('',#16840,#16841,#1401,.T.); -#24292=EDGE_CURVE('',#16945,#16840,#1405,.T.); -#24296=EDGE_CURVE('',#16955,#16957,#1409,.T.); -#24298=EDGE_CURVE('',#16877,#16957,#1413,.T.); -#24300=EDGE_CURVE('',#16876,#16877,#1417,.T.); -#24302=EDGE_CURVE('',#16955,#16876,#1421,.T.); -#24306=EDGE_CURVE('',#16829,#16911,#1425,.T.); -#24308=EDGE_CURVE('',#16879,#16911,#1429,.T.); -#24310=EDGE_CURVE('',#16845,#16879,#1433,.T.); -#24312=EDGE_CURVE('',#16844,#16845,#1437,.T.); -#24314=EDGE_CURVE('',#16959,#16844,#1441,.T.); -#24316=EDGE_CURVE('',#16959,#16829,#1445,.T.); -#24320=EDGE_CURVE('',#16913,#16915,#1449,.T.); -#24322=EDGE_CURVE('',#16883,#16915,#1453,.T.); -#24324=EDGE_CURVE('',#16882,#16883,#1457,.T.); -#24326=EDGE_CURVE('',#16913,#16882,#1461,.T.); -#24330=EDGE_CURVE('',#16831,#16923,#1465,.T.); -#24332=EDGE_CURVE('',#16867,#16923,#1469,.T.); -#24334=EDGE_CURVE('',#16849,#16867,#1473,.T.); -#24336=EDGE_CURVE('',#16848,#16849,#1477,.T.); -#24338=EDGE_CURVE('',#16917,#16848,#1481,.T.); -#24340=EDGE_CURVE('',#16917,#16831,#1485,.T.); -#24344=EDGE_CURVE('',#16833,#16939,#1353,.T.); -#24346=EDGE_CURVE('',#16869,#16939,#1357,.T.); -#24348=EDGE_CURVE('',#16837,#16869,#1361,.T.); -#24350=EDGE_CURVE('',#16836,#16837,#1365,.T.); -#24352=EDGE_CURVE('',#16925,#16836,#1369,.T.); -#24354=EDGE_CURVE('',#16925,#16833,#1373,.T.); -#24358=ADVANCED_FACE('',(#24275,#24285,#24295,#24305,#24319,#24329,#24343, -#24357),#24126,.T.); -#24371=EDGE_CURVE('',#16928,#16929,#1781,.T.); -#24373=EDGE_CURVE('',#16939,#16928,#1785,.T.); -#24376=EDGE_CURVE('',#16833,#16825,#1789,.T.); -#24378=EDGE_CURVE('',#16827,#16825,#1985,.T.); -#24380=EDGE_CURVE('',#16937,#16827,#1957,.T.); -#24382=EDGE_CURVE('',#16936,#16937,#1793,.T.); -#24384=EDGE_CURVE('',#16947,#16936,#1797,.T.); -#24387=EDGE_CURVE('',#16945,#16933,#1801,.T.); -#24389=EDGE_CURVE('',#16932,#16933,#1805,.T.); -#24391=EDGE_CURVE('',#16943,#16932,#1809,.T.); -#24394=EDGE_CURVE('',#16941,#16929,#1813,.T.); -#24398=ADVANCED_FACE('',(#24397),#24370,.T.); -#24404=EDGE_CURVE('',#16904,#16905,#1913,.T.); -#24406=EDGE_CURVE('',#16905,#16900,#1817,.T.); -#24408=EDGE_CURVE('',#16900,#16901,#1821,.T.); -#24410=EDGE_CURVE('',#16901,#16908,#1825,.T.); -#24412=EDGE_CURVE('',#16908,#16909,#1929,.T.); -#24414=EDGE_CURVE('',#16909,#16864,#1829,.T.); -#24416=EDGE_CURVE('',#16864,#16865,#1833,.T.); -#24418=EDGE_CURVE('',#16865,#16885,#1837,.T.); -#24420=EDGE_CURVE('',#16885,#16920,#1841,.T.); -#24422=EDGE_CURVE('',#16920,#16921,#6538,.T.); -#24424=EDGE_CURVE('',#16921,#16852,#1845,.T.); -#24426=EDGE_CURVE('',#16852,#16853,#1849,.T.); -#24428=EDGE_CURVE('',#16853,#16887,#1853,.T.); -#24430=EDGE_CURVE('',#16887,#16928,#1857,.T.); -#24433=EDGE_CURVE('',#16929,#16890,#1861,.T.); -#24435=EDGE_CURVE('',#16890,#16891,#1865,.T.); -#24437=EDGE_CURVE('',#16891,#16932,#1869,.T.); -#24440=EDGE_CURVE('',#16933,#16856,#1873,.T.); -#24442=EDGE_CURVE('',#16856,#16857,#1877,.T.); -#24444=EDGE_CURVE('',#16857,#16936,#1881,.T.); -#24447=EDGE_CURVE('',#16937,#16949,#1953,.T.); -#24449=EDGE_CURVE('',#16949,#16894,#1885,.T.); -#24451=EDGE_CURVE('',#16894,#16895,#1889,.T.); -#24453=EDGE_CURVE('',#16895,#16952,#1893,.T.); -#24455=EDGE_CURVE('',#16952,#16953,#1965,.T.); -#24457=EDGE_CURVE('',#16953,#16860,#1897,.T.); -#24459=EDGE_CURVE('',#16860,#16861,#1901,.T.); -#24461=EDGE_CURVE('',#16861,#16897,#1905,.T.); -#24463=EDGE_CURVE('',#16897,#16904,#1909,.T.); -#24467=ADVANCED_FACE('',(#24466),#24403,.F.); -#24474=EDGE_CURVE('',#16911,#16904,#1917,.T.); -#24477=EDGE_CURVE('',#16829,#16823,#1921,.T.); -#24479=EDGE_CURVE('',#16822,#16823,#1977,.T.); -#24481=EDGE_CURVE('',#16831,#16822,#6546,.T.); -#24484=EDGE_CURVE('',#16917,#16909,#1925,.T.); -#24487=EDGE_CURVE('',#16915,#16908,#1933,.T.); -#24490=EDGE_CURVE('',#16913,#16905,#1937,.T.); -#24494=ADVANCED_FACE('',(#24493),#24472,.T.); -#24502=EDGE_CURVE('',#16879,#16897,#1941,.T.); -#24507=ADVANCED_FACE('',(#24506),#24499,.F.); -#24516=EDGE_CURVE('',#16845,#16861,#1945,.T.); -#24520=ADVANCED_FACE('',(#24519),#24512,.F.); -#24529=EDGE_CURVE('',#16844,#16860,#1949,.T.); -#24533=ADVANCED_FACE('',(#24532),#24525,.F.); -#24539=EDGE_CURVE('',#16959,#16953,#1961,.T.); -#24546=ADVANCED_FACE('',(#24545),#24538,.F.); -#24554=EDGE_CURVE('',#16823,#16827,#1981,.T.); -#24560=EDGE_CURVE('',#16957,#16952,#1969,.T.); -#24563=EDGE_CURVE('',#16955,#16949,#1973,.T.); -#24567=ADVANCED_FACE('',(#24566),#24551,.T.); -#24576=EDGE_CURVE('',#16825,#16822,#1989,.T.); -#24580=EDGE_CURVE('',#17966,#17967,#1993,.T.); -#24582=EDGE_CURVE('',#17967,#17969,#1997,.T.); -#24584=EDGE_CURVE('',#17969,#17971,#2001,.T.); -#24586=EDGE_CURVE('',#17971,#17973,#2005,.T.); -#24588=EDGE_CURVE('',#17973,#17975,#2009,.T.); -#24590=EDGE_CURVE('',#17975,#17977,#2013,.T.); -#24592=EDGE_CURVE('',#17977,#17979,#2017,.T.); -#24594=EDGE_CURVE('',#17979,#17981,#2021,.T.); -#24596=EDGE_CURVE('',#17981,#17983,#2025,.T.); -#24598=EDGE_CURVE('',#17983,#17985,#2029,.T.); -#24600=EDGE_CURVE('',#17985,#17987,#2033,.T.); -#24602=EDGE_CURVE('',#17987,#17989,#2037,.T.); -#24604=EDGE_CURVE('',#17989,#17991,#2041,.T.); -#24606=EDGE_CURVE('',#17991,#17993,#2045,.T.); -#24608=EDGE_CURVE('',#17993,#17995,#2049,.T.); -#24610=EDGE_CURVE('',#17995,#17997,#2053,.T.); -#24612=EDGE_CURVE('',#17997,#17999,#2057,.T.); -#24614=EDGE_CURVE('',#17999,#18001,#2061,.T.); -#24616=EDGE_CURVE('',#18001,#17966,#2065,.T.); -#24620=EDGE_CURVE('',#18044,#18045,#2149,.T.); -#24622=EDGE_CURVE('',#18045,#18047,#2153,.T.); -#24624=EDGE_CURVE('',#18047,#18049,#2157,.T.); -#24626=EDGE_CURVE('',#18049,#18051,#2161,.T.); -#24628=EDGE_CURVE('',#18051,#18053,#2165,.T.); -#24630=EDGE_CURVE('',#18053,#18055,#2169,.T.); -#24632=EDGE_CURVE('',#18055,#18057,#2173,.T.); -#24634=EDGE_CURVE('',#18057,#18044,#2177,.T.); -#24638=EDGE_CURVE('',#18060,#18061,#2181,.T.); -#24640=EDGE_CURVE('',#18061,#18063,#2185,.T.); -#24642=EDGE_CURVE('',#18063,#18065,#2189,.T.); -#24644=EDGE_CURVE('',#18065,#18067,#2193,.T.); -#24646=EDGE_CURVE('',#18067,#18069,#2197,.T.); -#24648=EDGE_CURVE('',#18069,#18071,#2201,.T.); -#24650=EDGE_CURVE('',#18071,#18073,#2205,.T.); -#24652=EDGE_CURVE('',#18073,#18075,#2209,.T.); -#24654=EDGE_CURVE('',#18075,#18077,#2213,.T.); -#24656=EDGE_CURVE('',#18077,#18079,#2217,.T.); -#24658=EDGE_CURVE('',#18079,#18081,#2221,.T.); -#24660=EDGE_CURVE('',#18081,#18083,#2225,.T.); -#24662=EDGE_CURVE('',#18083,#18085,#2229,.T.); -#24664=EDGE_CURVE('',#18085,#18087,#2233,.T.); -#24666=EDGE_CURVE('',#18087,#18089,#2237,.T.); -#24668=EDGE_CURVE('',#18089,#18091,#2241,.T.); -#24670=EDGE_CURVE('',#18091,#18093,#2245,.T.); -#24672=EDGE_CURVE('',#18093,#18095,#2249,.T.); -#24674=EDGE_CURVE('',#18095,#18097,#2253,.T.); -#24676=EDGE_CURVE('',#18097,#18099,#2257,.T.); -#24678=EDGE_CURVE('',#18099,#18101,#2261,.T.); -#24680=EDGE_CURVE('',#18101,#18103,#2265,.T.); -#24682=EDGE_CURVE('',#18103,#18105,#2269,.T.); -#24684=EDGE_CURVE('',#18105,#18107,#2273,.T.); -#24686=EDGE_CURVE('',#18107,#18109,#2277,.T.); -#24688=EDGE_CURVE('',#18109,#18111,#2281,.T.); -#24690=EDGE_CURVE('',#18111,#18113,#2285,.T.); -#24692=EDGE_CURVE('',#18113,#18115,#2289,.T.); -#24694=EDGE_CURVE('',#18115,#18117,#2293,.T.); -#24696=EDGE_CURVE('',#18117,#18119,#2297,.T.); -#24698=EDGE_CURVE('',#18119,#18121,#2301,.T.); -#24700=EDGE_CURVE('',#18121,#18123,#2305,.T.); -#24702=EDGE_CURVE('',#18123,#18125,#2309,.T.); -#24704=EDGE_CURVE('',#18125,#18060,#2313,.T.); -#24708=EDGE_CURVE('',#18192,#18193,#2445,.T.); -#24710=EDGE_CURVE('',#18193,#18195,#2449,.T.); -#24712=EDGE_CURVE('',#18195,#18197,#2453,.T.); -#24714=EDGE_CURVE('',#18197,#18199,#2457,.T.); -#24716=EDGE_CURVE('',#18199,#18201,#2461,.T.); -#24718=EDGE_CURVE('',#18201,#18203,#2465,.T.); -#24720=EDGE_CURVE('',#18203,#18205,#2469,.T.); -#24722=EDGE_CURVE('',#18205,#18207,#2473,.T.); -#24724=EDGE_CURVE('',#18207,#18209,#2477,.T.); -#24726=EDGE_CURVE('',#18209,#18211,#2481,.T.); -#24728=EDGE_CURVE('',#18211,#18213,#2485,.T.); -#24730=EDGE_CURVE('',#18213,#18215,#2489,.T.); -#24732=EDGE_CURVE('',#18215,#18217,#2493,.T.); -#24734=EDGE_CURVE('',#18217,#18219,#2497,.T.); -#24736=EDGE_CURVE('',#18219,#18221,#2501,.T.); -#24738=EDGE_CURVE('',#18221,#18223,#2505,.T.); -#24740=EDGE_CURVE('',#18223,#18225,#2509,.T.); -#24742=EDGE_CURVE('',#18225,#18227,#2513,.T.); -#24744=EDGE_CURVE('',#18227,#18229,#2517,.T.); -#24746=EDGE_CURVE('',#18229,#18231,#2521,.T.); -#24748=EDGE_CURVE('',#18231,#18233,#2525,.T.); -#24750=EDGE_CURVE('',#18233,#18235,#2529,.T.); -#24752=EDGE_CURVE('',#18235,#18237,#2533,.T.); -#24754=EDGE_CURVE('',#18237,#18239,#2537,.T.); -#24756=EDGE_CURVE('',#18239,#18241,#2541,.T.); -#24758=EDGE_CURVE('',#18241,#18243,#2545,.T.); -#24760=EDGE_CURVE('',#18243,#18245,#2549,.T.); -#24762=EDGE_CURVE('',#18245,#18247,#2553,.T.); -#24764=EDGE_CURVE('',#18247,#18249,#2557,.T.); -#24766=EDGE_CURVE('',#18249,#18251,#2561,.T.); -#24768=EDGE_CURVE('',#18251,#18253,#2565,.T.); -#24770=EDGE_CURVE('',#18253,#18255,#2569,.T.); -#24772=EDGE_CURVE('',#18255,#18257,#2573,.T.); -#24774=EDGE_CURVE('',#18257,#18259,#2577,.T.); -#24776=EDGE_CURVE('',#18259,#18261,#2581,.T.); -#24778=EDGE_CURVE('',#18261,#18263,#2585,.T.); -#24780=EDGE_CURVE('',#18263,#18265,#2589,.T.); -#24782=EDGE_CURVE('',#18265,#18267,#2593,.T.); -#24784=EDGE_CURVE('',#18267,#18269,#2597,.T.); -#24786=EDGE_CURVE('',#18269,#18271,#2601,.T.); -#24788=EDGE_CURVE('',#18271,#18273,#2605,.T.); -#24790=EDGE_CURVE('',#18273,#18275,#2609,.T.); -#24792=EDGE_CURVE('',#18275,#18277,#2613,.T.); -#24794=EDGE_CURVE('',#18277,#18279,#2617,.T.); -#24796=EDGE_CURVE('',#18279,#18281,#2621,.T.); -#24798=EDGE_CURVE('',#18281,#18283,#2625,.T.); -#24800=EDGE_CURVE('',#18283,#18285,#2629,.T.); -#24802=EDGE_CURVE('',#18285,#18287,#2633,.T.); -#24804=EDGE_CURVE('',#18287,#18289,#2637,.T.); -#24806=EDGE_CURVE('',#18289,#18291,#2641,.T.); -#24808=EDGE_CURVE('',#18291,#18293,#2645,.T.); -#24810=EDGE_CURVE('',#18293,#18295,#2649,.T.); -#24812=EDGE_CURVE('',#18295,#18297,#2653,.T.); -#24814=EDGE_CURVE('',#18297,#18299,#2657,.T.); -#24816=EDGE_CURVE('',#18299,#18301,#2661,.T.); -#24818=EDGE_CURVE('',#18301,#18303,#2665,.T.); -#24820=EDGE_CURVE('',#18303,#18192,#2669,.T.); -#24824=EDGE_CURVE('',#18306,#18307,#2673,.T.); -#24826=EDGE_CURVE('',#18307,#18309,#2677,.T.); -#24828=EDGE_CURVE('',#18309,#18311,#2681,.T.); -#24830=EDGE_CURVE('',#18311,#18313,#2685,.T.); -#24832=EDGE_CURVE('',#18313,#18315,#2689,.T.); -#24834=EDGE_CURVE('',#18315,#18317,#2693,.T.); -#24836=EDGE_CURVE('',#18317,#18319,#2697,.T.); -#24838=EDGE_CURVE('',#18319,#18321,#2701,.T.); -#24840=EDGE_CURVE('',#18321,#18323,#2705,.T.); -#24842=EDGE_CURVE('',#18323,#18325,#2709,.T.); -#24844=EDGE_CURVE('',#18325,#18327,#2713,.T.); -#24846=EDGE_CURVE('',#18327,#18329,#2717,.T.); -#24848=EDGE_CURVE('',#18329,#18331,#2721,.T.); -#24850=EDGE_CURVE('',#18331,#18333,#2725,.T.); -#24852=EDGE_CURVE('',#18333,#18335,#2729,.T.); -#24854=EDGE_CURVE('',#18335,#18337,#2733,.T.); -#24856=EDGE_CURVE('',#18337,#18339,#2737,.T.); -#24858=EDGE_CURVE('',#18339,#18341,#2741,.T.); -#24860=EDGE_CURVE('',#18341,#18343,#2745,.T.); -#24862=EDGE_CURVE('',#18343,#18345,#2749,.T.); -#24864=EDGE_CURVE('',#18345,#18347,#2753,.T.); -#24866=EDGE_CURVE('',#18347,#18349,#2757,.T.); -#24868=EDGE_CURVE('',#18349,#18351,#2761,.T.); -#24870=EDGE_CURVE('',#18351,#18353,#2765,.T.); -#24872=EDGE_CURVE('',#18353,#18355,#2769,.T.); -#24874=EDGE_CURVE('',#18355,#18357,#2773,.T.); -#24876=EDGE_CURVE('',#18357,#18359,#2777,.T.); -#24878=EDGE_CURVE('',#18359,#18306,#2781,.T.); -#24882=EDGE_CURVE('',#18362,#18363,#2785,.T.); -#24884=EDGE_CURVE('',#18363,#18365,#2789,.T.); -#24886=EDGE_CURVE('',#18365,#18367,#2793,.T.); -#24888=EDGE_CURVE('',#18367,#18369,#2797,.T.); -#24890=EDGE_CURVE('',#18369,#18371,#2801,.T.); -#24892=EDGE_CURVE('',#18371,#18373,#2805,.T.); -#24894=EDGE_CURVE('',#18373,#18375,#2809,.T.); -#24896=EDGE_CURVE('',#18375,#18377,#2813,.T.); -#24898=EDGE_CURVE('',#18377,#18379,#2817,.T.); -#24900=EDGE_CURVE('',#18379,#18381,#2821,.T.); -#24902=EDGE_CURVE('',#18381,#18383,#2825,.T.); -#24904=EDGE_CURVE('',#18383,#18362,#2829,.T.); -#24908=EDGE_CURVE('',#20284,#20285,#2833,.T.); -#24910=EDGE_CURVE('',#20285,#20287,#2837,.T.); -#24912=EDGE_CURVE('',#20287,#20289,#2841,.T.); -#24914=EDGE_CURVE('',#20289,#20291,#2845,.T.); -#24916=EDGE_CURVE('',#20291,#20293,#2849,.T.); -#24918=EDGE_CURVE('',#20293,#20295,#2853,.T.); -#24920=EDGE_CURVE('',#20295,#20297,#2857,.T.); -#24922=EDGE_CURVE('',#20297,#20299,#2861,.T.); -#24924=EDGE_CURVE('',#20299,#20301,#2865,.T.); -#24926=EDGE_CURVE('',#20301,#20284,#2869,.T.); -#24930=EDGE_CURVE('',#20304,#20305,#2873,.T.); -#24932=EDGE_CURVE('',#20305,#20307,#2877,.T.); -#24934=EDGE_CURVE('',#20307,#20309,#2881,.T.); -#24936=EDGE_CURVE('',#20309,#20311,#2885,.T.); -#24938=EDGE_CURVE('',#20311,#20313,#2889,.T.); -#24940=EDGE_CURVE('',#20313,#20315,#2893,.T.); -#24942=EDGE_CURVE('',#20315,#20317,#2897,.T.); -#24944=EDGE_CURVE('',#20317,#20319,#2901,.T.); -#24946=EDGE_CURVE('',#20319,#20321,#2905,.T.); -#24948=EDGE_CURVE('',#20321,#20323,#2909,.T.); -#24950=EDGE_CURVE('',#20323,#20325,#2913,.T.); -#24952=EDGE_CURVE('',#20325,#20327,#2917,.T.); -#24954=EDGE_CURVE('',#20327,#20329,#2921,.T.); -#24956=EDGE_CURVE('',#20329,#20331,#2925,.T.); -#24958=EDGE_CURVE('',#20331,#20333,#2929,.T.); -#24960=EDGE_CURVE('',#20333,#20335,#2933,.T.); -#24962=EDGE_CURVE('',#20335,#20337,#2937,.T.); -#24964=EDGE_CURVE('',#20337,#20339,#2941,.T.); -#24966=EDGE_CURVE('',#20339,#20341,#2945,.T.); -#24968=EDGE_CURVE('',#20341,#20343,#2949,.T.); -#24970=EDGE_CURVE('',#20343,#20345,#2953,.T.); -#24972=EDGE_CURVE('',#20345,#20347,#2957,.T.); -#24974=EDGE_CURVE('',#20347,#20349,#2961,.T.); -#24976=EDGE_CURVE('',#20349,#20351,#2965,.T.); -#24978=EDGE_CURVE('',#20351,#20353,#2969,.T.); -#24980=EDGE_CURVE('',#20353,#20355,#2973,.T.); -#24982=EDGE_CURVE('',#20355,#20357,#2977,.T.); -#24984=EDGE_CURVE('',#20357,#20359,#2981,.T.); -#24986=EDGE_CURVE('',#20359,#20361,#2985,.T.); -#24988=EDGE_CURVE('',#20361,#20363,#2989,.T.); -#24990=EDGE_CURVE('',#20363,#20365,#2993,.T.); -#24992=EDGE_CURVE('',#20365,#20367,#2997,.T.); -#24994=EDGE_CURVE('',#20367,#20369,#3001,.T.); -#24996=EDGE_CURVE('',#20369,#20371,#3005,.T.); -#24998=EDGE_CURVE('',#20371,#20373,#3009,.T.); -#25000=EDGE_CURVE('',#20373,#20375,#3013,.T.); -#25002=EDGE_CURVE('',#20375,#20377,#3017,.T.); -#25004=EDGE_CURVE('',#20377,#20379,#3021,.T.); -#25006=EDGE_CURVE('',#20379,#20381,#3025,.T.); -#25008=EDGE_CURVE('',#20381,#20304,#3029,.T.); -#25012=EDGE_CURVE('',#20384,#20385,#3033,.T.); -#25014=EDGE_CURVE('',#20385,#20387,#3037,.T.); -#25016=EDGE_CURVE('',#20387,#20389,#3041,.T.); -#25018=EDGE_CURVE('',#20389,#20391,#3045,.T.); -#25020=EDGE_CURVE('',#20391,#20393,#3049,.T.); -#25022=EDGE_CURVE('',#20393,#20395,#3053,.T.); -#25024=EDGE_CURVE('',#20395,#20397,#3057,.T.); -#25026=EDGE_CURVE('',#20397,#20399,#3061,.T.); -#25028=EDGE_CURVE('',#20399,#20401,#3065,.T.); -#25030=EDGE_CURVE('',#20401,#20403,#3069,.T.); -#25032=EDGE_CURVE('',#20403,#20405,#3073,.T.); -#25034=EDGE_CURVE('',#20405,#20407,#3077,.T.); -#25036=EDGE_CURVE('',#20407,#20409,#3081,.T.); -#25038=EDGE_CURVE('',#20409,#20411,#3085,.T.); -#25040=EDGE_CURVE('',#20411,#20413,#3089,.T.); -#25042=EDGE_CURVE('',#20413,#20415,#3093,.T.); -#25044=EDGE_CURVE('',#20415,#20417,#3097,.T.); -#25046=EDGE_CURVE('',#20417,#20419,#3101,.T.); -#25048=EDGE_CURVE('',#20419,#20421,#3105,.T.); -#25050=EDGE_CURVE('',#20421,#20423,#3109,.T.); -#25052=EDGE_CURVE('',#20423,#20425,#3113,.T.); -#25054=EDGE_CURVE('',#20425,#20427,#3117,.T.); -#25056=EDGE_CURVE('',#20427,#20429,#3121,.T.); -#25058=EDGE_CURVE('',#20429,#20431,#3125,.T.); -#25060=EDGE_CURVE('',#20431,#20433,#3129,.T.); -#25062=EDGE_CURVE('',#20433,#20435,#3133,.T.); -#25064=EDGE_CURVE('',#20435,#20437,#3137,.T.); -#25066=EDGE_CURVE('',#20437,#20439,#3141,.T.); -#25068=EDGE_CURVE('',#20439,#20441,#3145,.T.); -#25070=EDGE_CURVE('',#20441,#20443,#3149,.T.); -#25072=EDGE_CURVE('',#20443,#20445,#3153,.T.); -#25074=EDGE_CURVE('',#20445,#20447,#3157,.T.); -#25076=EDGE_CURVE('',#20447,#20449,#3161,.T.); -#25078=EDGE_CURVE('',#20449,#20451,#3165,.T.); -#25080=EDGE_CURVE('',#20451,#20453,#3169,.T.); -#25082=EDGE_CURVE('',#20453,#20455,#3173,.T.); -#25084=EDGE_CURVE('',#20455,#20457,#3177,.T.); -#25086=EDGE_CURVE('',#20457,#20459,#3181,.T.); -#25088=EDGE_CURVE('',#20459,#20461,#3185,.T.); -#25090=EDGE_CURVE('',#20461,#20384,#3189,.T.); -#25094=EDGE_CURVE('',#20464,#20465,#3193,.T.); -#25096=EDGE_CURVE('',#20465,#20467,#3197,.T.); -#25098=EDGE_CURVE('',#20467,#20469,#3201,.T.); -#25100=EDGE_CURVE('',#20469,#20464,#3205,.T.); -#25104=EDGE_CURVE('',#20472,#20473,#3209,.T.); -#25106=EDGE_CURVE('',#20473,#20475,#3213,.T.); -#25108=EDGE_CURVE('',#20475,#20477,#3217,.T.); -#25110=EDGE_CURVE('',#20477,#20479,#3221,.T.); -#25112=EDGE_CURVE('',#20479,#20481,#3225,.T.); -#25114=EDGE_CURVE('',#20481,#20483,#3229,.T.); -#25116=EDGE_CURVE('',#20483,#20485,#3233,.T.); -#25118=EDGE_CURVE('',#20485,#20487,#3237,.T.); -#25120=EDGE_CURVE('',#20487,#20489,#3241,.T.); -#25122=EDGE_CURVE('',#20489,#20491,#3245,.T.); -#25124=EDGE_CURVE('',#20491,#20493,#3249,.T.); -#25126=EDGE_CURVE('',#20493,#20495,#3253,.T.); -#25128=EDGE_CURVE('',#20495,#20497,#3257,.T.); -#25130=EDGE_CURVE('',#20497,#20472,#3261,.T.); -#25134=EDGE_CURVE('',#20524,#20525,#3313,.T.); -#25136=EDGE_CURVE('',#20525,#20527,#3317,.T.); -#25138=EDGE_CURVE('',#20527,#20529,#3321,.T.); -#25140=EDGE_CURVE('',#20529,#20524,#3325,.T.); -#25144=EDGE_CURVE('',#20532,#20533,#3329,.T.); -#25146=EDGE_CURVE('',#20533,#20535,#3333,.T.); -#25148=EDGE_CURVE('',#20535,#20537,#3337,.T.); -#25150=EDGE_CURVE('',#20537,#20532,#3341,.T.); -#25154=EDGE_CURVE('',#20540,#20541,#3345,.T.); -#25156=EDGE_CURVE('',#20541,#20543,#3349,.T.); -#25158=EDGE_CURVE('',#20543,#20545,#3353,.T.); -#25160=EDGE_CURVE('',#20545,#20547,#3357,.T.); -#25162=EDGE_CURVE('',#20547,#20549,#3361,.T.); -#25164=EDGE_CURVE('',#20549,#20551,#3365,.T.); -#25166=EDGE_CURVE('',#20551,#20553,#3369,.T.); -#25168=EDGE_CURVE('',#20553,#20555,#3373,.T.); -#25170=EDGE_CURVE('',#20555,#20557,#3377,.T.); -#25172=EDGE_CURVE('',#20557,#20559,#3381,.T.); -#25174=EDGE_CURVE('',#20559,#20561,#3385,.T.); -#25176=EDGE_CURVE('',#20561,#20540,#3389,.T.); -#25180=EDGE_CURVE('',#20564,#20565,#3393,.T.); -#25182=EDGE_CURVE('',#20565,#20567,#3397,.T.); -#25184=EDGE_CURVE('',#20567,#20569,#3401,.T.); -#25186=EDGE_CURVE('',#20569,#20571,#3405,.T.); -#25188=EDGE_CURVE('',#20571,#20573,#3409,.T.); -#25190=EDGE_CURVE('',#20573,#20575,#3413,.T.); -#25192=EDGE_CURVE('',#20575,#20577,#3417,.T.); -#25194=EDGE_CURVE('',#20577,#20579,#3421,.T.); -#25196=EDGE_CURVE('',#20579,#20581,#3425,.T.); -#25198=EDGE_CURVE('',#20581,#20583,#3429,.T.); -#25200=EDGE_CURVE('',#20583,#20585,#3433,.T.); -#25202=EDGE_CURVE('',#20585,#20587,#3437,.T.); -#25204=EDGE_CURVE('',#20587,#20589,#3441,.T.); -#25206=EDGE_CURVE('',#20589,#20591,#3445,.T.); -#25208=EDGE_CURVE('',#20591,#20593,#3449,.T.); -#25210=EDGE_CURVE('',#20593,#20595,#3453,.T.); -#25212=EDGE_CURVE('',#20595,#20597,#3457,.T.); -#25214=EDGE_CURVE('',#20597,#20599,#3461,.T.); -#25216=EDGE_CURVE('',#20599,#20601,#3465,.T.); -#25218=EDGE_CURVE('',#20601,#20603,#3469,.T.); -#25220=EDGE_CURVE('',#20603,#20605,#3473,.T.); -#25222=EDGE_CURVE('',#20605,#20607,#3477,.T.); -#25224=EDGE_CURVE('',#20607,#20609,#3481,.T.); -#25226=EDGE_CURVE('',#20609,#20611,#3485,.T.); -#25228=EDGE_CURVE('',#20611,#20613,#3489,.T.); -#25230=EDGE_CURVE('',#20613,#20615,#3493,.T.); -#25232=EDGE_CURVE('',#20615,#20617,#3497,.T.); -#25234=EDGE_CURVE('',#20617,#20619,#3501,.T.); -#25236=EDGE_CURVE('',#20619,#20621,#3505,.T.); -#25238=EDGE_CURVE('',#20621,#20623,#3509,.T.); -#25240=EDGE_CURVE('',#20623,#20625,#3513,.T.); -#25242=EDGE_CURVE('',#20625,#20627,#3517,.T.); -#25244=EDGE_CURVE('',#20627,#20629,#3521,.T.); -#25246=EDGE_CURVE('',#20629,#20564,#3525,.T.); -#25250=EDGE_CURVE('',#20696,#20697,#3657,.T.); -#25252=EDGE_CURVE('',#20697,#20699,#3661,.T.); -#25254=EDGE_CURVE('',#20699,#20701,#3665,.T.); -#25256=EDGE_CURVE('',#20701,#20703,#3669,.T.); -#25258=EDGE_CURVE('',#20703,#20705,#3673,.T.); -#25260=EDGE_CURVE('',#20705,#20707,#3677,.T.); -#25262=EDGE_CURVE('',#20707,#20709,#3681,.T.); -#25264=EDGE_CURVE('',#20709,#20711,#3685,.T.); -#25266=EDGE_CURVE('',#20711,#20713,#3689,.T.); -#25268=EDGE_CURVE('',#20713,#20715,#3693,.T.); -#25270=EDGE_CURVE('',#20715,#20717,#3697,.T.); -#25272=EDGE_CURVE('',#20717,#20719,#3701,.T.); -#25274=EDGE_CURVE('',#20719,#20696,#3705,.T.); -#25278=EDGE_CURVE('',#20722,#20723,#3709,.T.); -#25280=EDGE_CURVE('',#20723,#20725,#3713,.T.); -#25282=EDGE_CURVE('',#20725,#20727,#3717,.T.); -#25284=EDGE_CURVE('',#20727,#20729,#3721,.T.); -#25286=EDGE_CURVE('',#20729,#20731,#3725,.T.); -#25288=EDGE_CURVE('',#20731,#20733,#3729,.T.); -#25290=EDGE_CURVE('',#20733,#20735,#3733,.T.); -#25292=EDGE_CURVE('',#20735,#20737,#3737,.T.); -#25294=EDGE_CURVE('',#20737,#20739,#3741,.T.); -#25296=EDGE_CURVE('',#20739,#20741,#3745,.T.); -#25298=EDGE_CURVE('',#20741,#20743,#3749,.T.); -#25300=EDGE_CURVE('',#20743,#20745,#3753,.T.); -#25302=EDGE_CURVE('',#20745,#20747,#3757,.T.); -#25304=EDGE_CURVE('',#20747,#20749,#3761,.T.); -#25306=EDGE_CURVE('',#20749,#20751,#3765,.T.); -#25308=EDGE_CURVE('',#20751,#20753,#3769,.T.); -#25310=EDGE_CURVE('',#20753,#20755,#3773,.T.); -#25312=EDGE_CURVE('',#20755,#20757,#3777,.T.); -#25314=EDGE_CURVE('',#20757,#20722,#3781,.T.); -#25318=EDGE_CURVE('',#20800,#20801,#3865,.T.); -#25320=EDGE_CURVE('',#20801,#20803,#3869,.T.); -#25322=EDGE_CURVE('',#20803,#20805,#3873,.T.); -#25324=EDGE_CURVE('',#20805,#20807,#3877,.T.); -#25326=EDGE_CURVE('',#20807,#20809,#3881,.T.); -#25328=EDGE_CURVE('',#20809,#20811,#3885,.T.); -#25330=EDGE_CURVE('',#20811,#20813,#3889,.T.); -#25332=EDGE_CURVE('',#20813,#20800,#3893,.T.); -#25336=EDGE_CURVE('',#20816,#20817,#3897,.T.); -#25338=EDGE_CURVE('',#20817,#20819,#3901,.T.); -#25340=EDGE_CURVE('',#20819,#20821,#3905,.T.); -#25342=EDGE_CURVE('',#20821,#20823,#3909,.T.); -#25344=EDGE_CURVE('',#20823,#20825,#3913,.T.); -#25346=EDGE_CURVE('',#20825,#20827,#3917,.T.); -#25348=EDGE_CURVE('',#20827,#20829,#3921,.T.); -#25350=EDGE_CURVE('',#20829,#20831,#3925,.T.); -#25352=EDGE_CURVE('',#20831,#20833,#3929,.T.); -#25354=EDGE_CURVE('',#20833,#20835,#3933,.T.); -#25356=EDGE_CURVE('',#20835,#20837,#3937,.T.); -#25358=EDGE_CURVE('',#20837,#20839,#3941,.T.); -#25360=EDGE_CURVE('',#20839,#20841,#3945,.T.); -#25362=EDGE_CURVE('',#20841,#20843,#3949,.T.); -#25364=EDGE_CURVE('',#20843,#20845,#3953,.T.); -#25366=EDGE_CURVE('',#20845,#20847,#3957,.T.); -#25368=EDGE_CURVE('',#20847,#20849,#3961,.T.); -#25370=EDGE_CURVE('',#20849,#20851,#3965,.T.); -#25372=EDGE_CURVE('',#20851,#20853,#3969,.T.); -#25374=EDGE_CURVE('',#20853,#20855,#3973,.T.); -#25376=EDGE_CURVE('',#20855,#20857,#3977,.T.); -#25378=EDGE_CURVE('',#20857,#20859,#3981,.T.); -#25380=EDGE_CURVE('',#20859,#20861,#3985,.T.); -#25382=EDGE_CURVE('',#20861,#20863,#3989,.T.); -#25384=EDGE_CURVE('',#20863,#20865,#3993,.T.); -#25386=EDGE_CURVE('',#20865,#20867,#3997,.T.); -#25388=EDGE_CURVE('',#20867,#20869,#4001,.T.); -#25390=EDGE_CURVE('',#20869,#20871,#4005,.T.); -#25392=EDGE_CURVE('',#20871,#20873,#4009,.T.); -#25394=EDGE_CURVE('',#20873,#20875,#4013,.T.); -#25396=EDGE_CURVE('',#20875,#20877,#4017,.T.); -#25398=EDGE_CURVE('',#20877,#20879,#4021,.T.); -#25400=EDGE_CURVE('',#20879,#20881,#4025,.T.); -#25402=EDGE_CURVE('',#20881,#20816,#4029,.T.); -#25406=EDGE_CURVE('',#20948,#20949,#4161,.T.); -#25408=EDGE_CURVE('',#20949,#20951,#4165,.T.); -#25410=EDGE_CURVE('',#20951,#20953,#4169,.T.); -#25412=EDGE_CURVE('',#20953,#20955,#4173,.T.); -#25414=EDGE_CURVE('',#20955,#20957,#4177,.T.); -#25416=EDGE_CURVE('',#20957,#20959,#4181,.T.); -#25418=EDGE_CURVE('',#20959,#20961,#4185,.T.); -#25420=EDGE_CURVE('',#20961,#20963,#4189,.T.); -#25422=EDGE_CURVE('',#20963,#20965,#4193,.T.); -#25424=EDGE_CURVE('',#20965,#20967,#4197,.T.); -#25426=EDGE_CURVE('',#20967,#20969,#4201,.T.); -#25428=EDGE_CURVE('',#20969,#20971,#4205,.T.); -#25430=EDGE_CURVE('',#20971,#20973,#4209,.T.); -#25432=EDGE_CURVE('',#20973,#20975,#4213,.T.); -#25434=EDGE_CURVE('',#20975,#20977,#4217,.T.); -#25436=EDGE_CURVE('',#20977,#20979,#4221,.T.); -#25438=EDGE_CURVE('',#20979,#20981,#4225,.T.); -#25440=EDGE_CURVE('',#20981,#20983,#4229,.T.); -#25442=EDGE_CURVE('',#20983,#20985,#4233,.T.); -#25444=EDGE_CURVE('',#20985,#20987,#4237,.T.); -#25446=EDGE_CURVE('',#20987,#20989,#4241,.T.); -#25448=EDGE_CURVE('',#20989,#20991,#4245,.T.); -#25450=EDGE_CURVE('',#20991,#20993,#4249,.T.); -#25452=EDGE_CURVE('',#20993,#20995,#4253,.T.); -#25454=EDGE_CURVE('',#20995,#20997,#4257,.T.); -#25456=EDGE_CURVE('',#20997,#20999,#4261,.T.); -#25458=EDGE_CURVE('',#20999,#21001,#4265,.T.); -#25460=EDGE_CURVE('',#21001,#21003,#4269,.T.); -#25462=EDGE_CURVE('',#21003,#21005,#4273,.T.); -#25464=EDGE_CURVE('',#21005,#21007,#4277,.T.); -#25466=EDGE_CURVE('',#21007,#21009,#4281,.T.); -#25468=EDGE_CURVE('',#21009,#21011,#4285,.T.); -#25470=EDGE_CURVE('',#21011,#21013,#4289,.T.); -#25472=EDGE_CURVE('',#21013,#21015,#4293,.T.); -#25474=EDGE_CURVE('',#21015,#21017,#4297,.T.); -#25476=EDGE_CURVE('',#21017,#21019,#4301,.T.); -#25478=EDGE_CURVE('',#21019,#21021,#4305,.T.); -#25480=EDGE_CURVE('',#21021,#21023,#4309,.T.); -#25482=EDGE_CURVE('',#21023,#21025,#4313,.T.); -#25484=EDGE_CURVE('',#21025,#21027,#4317,.T.); -#25486=EDGE_CURVE('',#21027,#21029,#4321,.T.); -#25488=EDGE_CURVE('',#21029,#21031,#4325,.T.); -#25490=EDGE_CURVE('',#21031,#21033,#4329,.T.); -#25492=EDGE_CURVE('',#21033,#21035,#4333,.T.); -#25494=EDGE_CURVE('',#21035,#21037,#4337,.T.); -#25496=EDGE_CURVE('',#21037,#21039,#4341,.T.); -#25498=EDGE_CURVE('',#21039,#21041,#4345,.T.); -#25500=EDGE_CURVE('',#21041,#21043,#4349,.T.); -#25502=EDGE_CURVE('',#21043,#21045,#4353,.T.); -#25504=EDGE_CURVE('',#21045,#21047,#4357,.T.); -#25506=EDGE_CURVE('',#21047,#21049,#4361,.T.); -#25508=EDGE_CURVE('',#21049,#21051,#4365,.T.); -#25510=EDGE_CURVE('',#21051,#21053,#4369,.T.); -#25512=EDGE_CURVE('',#21053,#21055,#4373,.T.); -#25514=EDGE_CURVE('',#21055,#21057,#4377,.T.); -#25516=EDGE_CURVE('',#21057,#21059,#4381,.T.); -#25518=EDGE_CURVE('',#21059,#20948,#4385,.T.); -#25522=EDGE_CURVE('',#21062,#21063,#4389,.T.); -#25524=EDGE_CURVE('',#21063,#21065,#4393,.T.); -#25526=EDGE_CURVE('',#21065,#21067,#4397,.T.); -#25528=EDGE_CURVE('',#21067,#21069,#4401,.T.); -#25530=EDGE_CURVE('',#21069,#21071,#4405,.T.); -#25532=EDGE_CURVE('',#21071,#21073,#4409,.T.); -#25534=EDGE_CURVE('',#21073,#21075,#4413,.T.); -#25536=EDGE_CURVE('',#21075,#21077,#4417,.T.); -#25538=EDGE_CURVE('',#21077,#21079,#4421,.T.); -#25540=EDGE_CURVE('',#21079,#21081,#4425,.T.); -#25542=EDGE_CURVE('',#21081,#21083,#4429,.T.); -#25544=EDGE_CURVE('',#21083,#21085,#4433,.T.); -#25546=EDGE_CURVE('',#21085,#21087,#4437,.T.); -#25548=EDGE_CURVE('',#21087,#21089,#4441,.T.); -#25550=EDGE_CURVE('',#21089,#21091,#4445,.T.); -#25552=EDGE_CURVE('',#21091,#21093,#4449,.T.); -#25554=EDGE_CURVE('',#21093,#21095,#4453,.T.); -#25556=EDGE_CURVE('',#21095,#21097,#4457,.T.); -#25558=EDGE_CURVE('',#21097,#21099,#4461,.T.); -#25560=EDGE_CURVE('',#21099,#21101,#4465,.T.); -#25562=EDGE_CURVE('',#21101,#21103,#4469,.T.); -#25564=EDGE_CURVE('',#21103,#21105,#4473,.T.); -#25566=EDGE_CURVE('',#21105,#21107,#4477,.T.); -#25568=EDGE_CURVE('',#21107,#21109,#4481,.T.); -#25570=EDGE_CURVE('',#21109,#21111,#4485,.T.); -#25572=EDGE_CURVE('',#21111,#21113,#4489,.T.); -#25574=EDGE_CURVE('',#21113,#21115,#4493,.T.); -#25576=EDGE_CURVE('',#21115,#21062,#4497,.T.); -#25580=EDGE_CURVE('',#21118,#21119,#4501,.T.); -#25582=EDGE_CURVE('',#21119,#21121,#4505,.T.); -#25584=EDGE_CURVE('',#21121,#21123,#4509,.T.); -#25586=EDGE_CURVE('',#21123,#21118,#4513,.T.); -#25590=EDGE_CURVE('',#21126,#21127,#4517,.T.); -#25592=EDGE_CURVE('',#21127,#21129,#4521,.T.); -#25594=EDGE_CURVE('',#21129,#21131,#4525,.T.); -#25596=EDGE_CURVE('',#21131,#21133,#4529,.T.); -#25598=EDGE_CURVE('',#21133,#21135,#4533,.T.); -#25600=EDGE_CURVE('',#21135,#21137,#4537,.T.); -#25602=EDGE_CURVE('',#21137,#21139,#4541,.T.); -#25604=EDGE_CURVE('',#21139,#21141,#4545,.T.); -#25606=EDGE_CURVE('',#21141,#21143,#4549,.T.); -#25608=EDGE_CURVE('',#21143,#21145,#4553,.T.); -#25610=EDGE_CURVE('',#21145,#21147,#4557,.T.); -#25612=EDGE_CURVE('',#21147,#21149,#4561,.T.); -#25614=EDGE_CURVE('',#21149,#21151,#4565,.T.); -#25616=EDGE_CURVE('',#21151,#21153,#4569,.T.); -#25618=EDGE_CURVE('',#21153,#21155,#4573,.T.); -#25620=EDGE_CURVE('',#21155,#21157,#4577,.T.); -#25622=EDGE_CURVE('',#21157,#21159,#4581,.T.); -#25624=EDGE_CURVE('',#21159,#21161,#4585,.T.); -#25626=EDGE_CURVE('',#21161,#21163,#4589,.T.); -#25628=EDGE_CURVE('',#21163,#21165,#4593,.T.); -#25630=EDGE_CURVE('',#21165,#21167,#4597,.T.); -#25632=EDGE_CURVE('',#21167,#21169,#4601,.T.); -#25634=EDGE_CURVE('',#21169,#21171,#4605,.T.); -#25636=EDGE_CURVE('',#21171,#21173,#4609,.T.); -#25638=EDGE_CURVE('',#21173,#21175,#4613,.T.); -#25640=EDGE_CURVE('',#21175,#21177,#4617,.T.); -#25642=EDGE_CURVE('',#21177,#21179,#4621,.T.); -#25644=EDGE_CURVE('',#21179,#21181,#4625,.T.); -#25646=EDGE_CURVE('',#21181,#21183,#4629,.T.); -#25648=EDGE_CURVE('',#21183,#21185,#4633,.T.); -#25650=EDGE_CURVE('',#21185,#21187,#4637,.T.); -#25652=EDGE_CURVE('',#21187,#21189,#4641,.T.); -#25654=EDGE_CURVE('',#21189,#21191,#4645,.T.); -#25656=EDGE_CURVE('',#21191,#21193,#4649,.T.); -#25658=EDGE_CURVE('',#21193,#21195,#4653,.T.); -#25660=EDGE_CURVE('',#21195,#21197,#4657,.T.); -#25662=EDGE_CURVE('',#21197,#21199,#4661,.T.); -#25664=EDGE_CURVE('',#21199,#21201,#4665,.T.); -#25666=EDGE_CURVE('',#21201,#21203,#4669,.T.); -#25668=EDGE_CURVE('',#21203,#21126,#4673,.T.); -#25672=EDGE_CURVE('',#21206,#21207,#4677,.T.); -#25674=EDGE_CURVE('',#21207,#21209,#4681,.T.); -#25676=EDGE_CURVE('',#21209,#21211,#4685,.T.); -#25678=EDGE_CURVE('',#21211,#21206,#4689,.T.); -#25682=EDGE_CURVE('',#21214,#21215,#4693,.T.); -#25684=EDGE_CURVE('',#21215,#21217,#4697,.T.); -#25686=EDGE_CURVE('',#21217,#21219,#4701,.T.); -#25688=EDGE_CURVE('',#21219,#21221,#4705,.T.); -#25690=EDGE_CURVE('',#21221,#21223,#4709,.T.); -#25692=EDGE_CURVE('',#21223,#21225,#4713,.T.); -#25694=EDGE_CURVE('',#21225,#21227,#4717,.T.); -#25696=EDGE_CURVE('',#21227,#21229,#4721,.T.); -#25698=EDGE_CURVE('',#21229,#21231,#4725,.T.); -#25700=EDGE_CURVE('',#21231,#21233,#4729,.T.); -#25702=EDGE_CURVE('',#21233,#21235,#4733,.T.); -#25704=EDGE_CURVE('',#21235,#21237,#4737,.T.); -#25706=EDGE_CURVE('',#21237,#21239,#4741,.T.); -#25708=EDGE_CURVE('',#21239,#21214,#4745,.T.); -#25712=EDGE_CURVE('',#21266,#21267,#4797,.T.); -#25714=EDGE_CURVE('',#21267,#21269,#4801,.T.); -#25716=EDGE_CURVE('',#21269,#21271,#4805,.T.); -#25718=EDGE_CURVE('',#21271,#21266,#4809,.T.); -#25722=EDGE_CURVE('',#21274,#21275,#4813,.T.); -#25724=EDGE_CURVE('',#21275,#21277,#4817,.T.); -#25726=EDGE_CURVE('',#21277,#21279,#4821,.T.); -#25728=EDGE_CURVE('',#21279,#21274,#4825,.T.); -#25732=EDGE_CURVE('',#21282,#21283,#4829,.T.); -#25734=EDGE_CURVE('',#21283,#21285,#4833,.T.); -#25736=EDGE_CURVE('',#21285,#21287,#4837,.T.); -#25738=EDGE_CURVE('',#21287,#21289,#4841,.T.); -#25740=EDGE_CURVE('',#21289,#21291,#4845,.T.); -#25742=EDGE_CURVE('',#21291,#21293,#4849,.T.); -#25744=EDGE_CURVE('',#21293,#21295,#4853,.T.); -#25746=EDGE_CURVE('',#21295,#21297,#4857,.T.); -#25748=EDGE_CURVE('',#21297,#21299,#4861,.T.); -#25750=EDGE_CURVE('',#21299,#21301,#4865,.T.); -#25752=EDGE_CURVE('',#21301,#21282,#4869,.T.); -#25756=EDGE_CURVE('',#21310,#21311,#4885,.T.); -#25758=EDGE_CURVE('',#21311,#21313,#4889,.T.); -#25760=EDGE_CURVE('',#21313,#21315,#4893,.T.); -#25762=EDGE_CURVE('',#21315,#21317,#4897,.T.); -#25764=EDGE_CURVE('',#21317,#21319,#4901,.T.); -#25766=EDGE_CURVE('',#21319,#21321,#4905,.T.); -#25768=EDGE_CURVE('',#21321,#21310,#4909,.T.); -#25772=EDGE_CURVE('',#21324,#21325,#4913,.T.); -#25774=EDGE_CURVE('',#21325,#21327,#4917,.T.); -#25776=EDGE_CURVE('',#21327,#21329,#4921,.T.); -#25778=EDGE_CURVE('',#21329,#21331,#4925,.T.); -#25780=EDGE_CURVE('',#21331,#21333,#4929,.T.); -#25782=EDGE_CURVE('',#21333,#21335,#4933,.T.); -#25784=EDGE_CURVE('',#21335,#21337,#4937,.T.); -#25786=EDGE_CURVE('',#21337,#21339,#4941,.T.); -#25788=EDGE_CURVE('',#21339,#21341,#4945,.T.); -#25790=EDGE_CURVE('',#21341,#21343,#4949,.T.); -#25792=EDGE_CURVE('',#21343,#21345,#4953,.T.); -#25794=EDGE_CURVE('',#21345,#21347,#4957,.T.); -#25796=EDGE_CURVE('',#21347,#21349,#4961,.T.); -#25798=EDGE_CURVE('',#21349,#21351,#4965,.T.); -#25800=EDGE_CURVE('',#21351,#21353,#4969,.T.); -#25802=EDGE_CURVE('',#21353,#21355,#4973,.T.); -#25804=EDGE_CURVE('',#21355,#21357,#4977,.T.); -#25806=EDGE_CURVE('',#21357,#21359,#4981,.T.); -#25808=EDGE_CURVE('',#21359,#21361,#4985,.T.); -#25810=EDGE_CURVE('',#21361,#21363,#4989,.T.); -#25812=EDGE_CURVE('',#21363,#21365,#4993,.T.); -#25814=EDGE_CURVE('',#21365,#21367,#4997,.T.); -#25816=EDGE_CURVE('',#21367,#21369,#5001,.T.); -#25818=EDGE_CURVE('',#21369,#21371,#5005,.T.); -#25820=EDGE_CURVE('',#21371,#21373,#5009,.T.); -#25822=EDGE_CURVE('',#21373,#21324,#5013,.T.); -#25826=EDGE_CURVE('',#21412,#21413,#5089,.T.); -#25828=EDGE_CURVE('',#21413,#21415,#5093,.T.); -#25830=EDGE_CURVE('',#21415,#21417,#5097,.T.); -#25832=EDGE_CURVE('',#21417,#21419,#5101,.T.); -#25834=EDGE_CURVE('',#21419,#21421,#5105,.T.); -#25836=EDGE_CURVE('',#21421,#21423,#5109,.T.); -#25838=EDGE_CURVE('',#21423,#21425,#5113,.T.); -#25840=EDGE_CURVE('',#21425,#21427,#5117,.T.); -#25842=EDGE_CURVE('',#21427,#21429,#5121,.T.); -#25844=EDGE_CURVE('',#21429,#21431,#5125,.T.); -#25846=EDGE_CURVE('',#21431,#21433,#5129,.T.); -#25848=EDGE_CURVE('',#21433,#21435,#5133,.T.); -#25850=EDGE_CURVE('',#21435,#21437,#5137,.T.); -#25852=EDGE_CURVE('',#21437,#21439,#5141,.T.); -#25854=EDGE_CURVE('',#21439,#21441,#5145,.T.); -#25856=EDGE_CURVE('',#21441,#21443,#5149,.T.); -#25858=EDGE_CURVE('',#21443,#21445,#5153,.T.); -#25860=EDGE_CURVE('',#21445,#21447,#5157,.T.); -#25862=EDGE_CURVE('',#21447,#21449,#5161,.T.); -#25864=EDGE_CURVE('',#21449,#21451,#5165,.T.); -#25866=EDGE_CURVE('',#21451,#21453,#5169,.T.); -#25868=EDGE_CURVE('',#21453,#21455,#5173,.T.); -#25870=EDGE_CURVE('',#21455,#21457,#5177,.T.); -#25872=EDGE_CURVE('',#21457,#21459,#5181,.T.); -#25874=EDGE_CURVE('',#21459,#21461,#5185,.T.); -#25876=EDGE_CURVE('',#21461,#21412,#5189,.T.); -#25880=EDGE_CURVE('',#21500,#21501,#5265,.T.); -#25882=EDGE_CURVE('',#21501,#21503,#5269,.T.); -#25884=EDGE_CURVE('',#21503,#21505,#5273,.T.); -#25886=EDGE_CURVE('',#21505,#21507,#5277,.T.); -#25888=EDGE_CURVE('',#21507,#21509,#5281,.T.); -#25890=EDGE_CURVE('',#21509,#21511,#5285,.T.); -#25892=EDGE_CURVE('',#21511,#21513,#5289,.T.); -#25894=EDGE_CURVE('',#21513,#21500,#5293,.T.); -#25898=EDGE_CURVE('',#21522,#21523,#5309,.T.); -#25900=EDGE_CURVE('',#21523,#21525,#5313,.T.); -#25902=EDGE_CURVE('',#21525,#21527,#5317,.T.); -#25904=EDGE_CURVE('',#21527,#21522,#5321,.T.); -#25908=EDGE_CURVE('',#21530,#21531,#5325,.T.); -#25910=EDGE_CURVE('',#21531,#21533,#5329,.T.); -#25912=EDGE_CURVE('',#21533,#21535,#5333,.T.); -#25914=EDGE_CURVE('',#21535,#21537,#5337,.T.); -#25916=EDGE_CURVE('',#21537,#21539,#5341,.T.); -#25918=EDGE_CURVE('',#21539,#21541,#5345,.T.); -#25920=EDGE_CURVE('',#21541,#21543,#5349,.T.); -#25922=EDGE_CURVE('',#21543,#21545,#5353,.T.); -#25924=EDGE_CURVE('',#21545,#21547,#5357,.T.); -#25926=EDGE_CURVE('',#21547,#21549,#5361,.T.); -#25928=EDGE_CURVE('',#21549,#21551,#5365,.T.); -#25930=EDGE_CURVE('',#21551,#21553,#5369,.T.); -#25932=EDGE_CURVE('',#21553,#21555,#5373,.T.); -#25934=EDGE_CURVE('',#21555,#21557,#5377,.T.); -#25936=EDGE_CURVE('',#21557,#21559,#5381,.T.); -#25938=EDGE_CURVE('',#21559,#21561,#5385,.T.); -#25940=EDGE_CURVE('',#21561,#21563,#5389,.T.); -#25942=EDGE_CURVE('',#21563,#21565,#5393,.T.); -#25944=EDGE_CURVE('',#21565,#21530,#5397,.T.); -#25948=EDGE_CURVE('',#21608,#21609,#5481,.T.); -#25950=EDGE_CURVE('',#21609,#21611,#5485,.T.); -#25952=EDGE_CURVE('',#21611,#21613,#5489,.T.); -#25954=EDGE_CURVE('',#21613,#21615,#5493,.T.); -#25956=EDGE_CURVE('',#21615,#21617,#5497,.T.); -#25958=EDGE_CURVE('',#21617,#21619,#5501,.T.); -#25960=EDGE_CURVE('',#21619,#21621,#5505,.T.); -#25962=EDGE_CURVE('',#21621,#21608,#5509,.T.); -#25966=EDGE_CURVE('',#21624,#21625,#5513,.T.); -#25968=EDGE_CURVE('',#21625,#21627,#5517,.T.); -#25970=EDGE_CURVE('',#21627,#21629,#5521,.T.); -#25972=EDGE_CURVE('',#21629,#21631,#5525,.T.); -#25974=EDGE_CURVE('',#21631,#21633,#5529,.T.); -#25976=EDGE_CURVE('',#21633,#21635,#5533,.T.); -#25978=EDGE_CURVE('',#21635,#21637,#5537,.T.); -#25980=EDGE_CURVE('',#21637,#21639,#5541,.T.); -#25982=EDGE_CURVE('',#21639,#21641,#5545,.T.); -#25984=EDGE_CURVE('',#21641,#21643,#5549,.T.); -#25986=EDGE_CURVE('',#21643,#21645,#5553,.T.); -#25988=EDGE_CURVE('',#21645,#21647,#5557,.T.); -#25990=EDGE_CURVE('',#21647,#21649,#5561,.T.); -#25992=EDGE_CURVE('',#21649,#21651,#5565,.T.); -#25994=EDGE_CURVE('',#21651,#21653,#5569,.T.); -#25996=EDGE_CURVE('',#21653,#21655,#5573,.T.); -#25998=EDGE_CURVE('',#21655,#21657,#5577,.T.); -#26000=EDGE_CURVE('',#21657,#21659,#5581,.T.); -#26002=EDGE_CURVE('',#21659,#21661,#5585,.T.); -#26004=EDGE_CURVE('',#21661,#21663,#5589,.T.); -#26006=EDGE_CURVE('',#21663,#21665,#5593,.T.); -#26008=EDGE_CURVE('',#21665,#21667,#5597,.T.); -#26010=EDGE_CURVE('',#21667,#21669,#5601,.T.); -#26012=EDGE_CURVE('',#21669,#21671,#5605,.T.); -#26014=EDGE_CURVE('',#21671,#21673,#5609,.T.); -#26016=EDGE_CURVE('',#21673,#21675,#5613,.T.); -#26018=EDGE_CURVE('',#21675,#21677,#5617,.T.); -#26020=EDGE_CURVE('',#21677,#21679,#5621,.T.); -#26022=EDGE_CURVE('',#21679,#21681,#5625,.T.); -#26024=EDGE_CURVE('',#21681,#21683,#5629,.T.); -#26026=EDGE_CURVE('',#21683,#21685,#5633,.T.); -#26028=EDGE_CURVE('',#21685,#21687,#5637,.T.); -#26030=EDGE_CURVE('',#21687,#21689,#5641,.T.); -#26032=EDGE_CURVE('',#21689,#21624,#5645,.T.); -#26036=EDGE_CURVE('',#21756,#21757,#5777,.T.); -#26038=EDGE_CURVE('',#21757,#21759,#5781,.T.); -#26040=EDGE_CURVE('',#21759,#21761,#5785,.T.); -#26042=EDGE_CURVE('',#21761,#21763,#5789,.T.); -#26044=EDGE_CURVE('',#21763,#21765,#5793,.T.); -#26046=EDGE_CURVE('',#21765,#21767,#5797,.T.); -#26048=EDGE_CURVE('',#21767,#21769,#5801,.T.); -#26050=EDGE_CURVE('',#21769,#21771,#5805,.T.); -#26052=EDGE_CURVE('',#21771,#21773,#5809,.T.); -#26054=EDGE_CURVE('',#21773,#21775,#5813,.T.); -#26056=EDGE_CURVE('',#21775,#21777,#5817,.T.); -#26058=EDGE_CURVE('',#21777,#21779,#5821,.T.); -#26060=EDGE_CURVE('',#21779,#21781,#5825,.T.); -#26062=EDGE_CURVE('',#21781,#21783,#5829,.T.); -#26064=EDGE_CURVE('',#21783,#21785,#5833,.T.); -#26066=EDGE_CURVE('',#21785,#21787,#5837,.T.); -#26068=EDGE_CURVE('',#21787,#21789,#5841,.T.); -#26070=EDGE_CURVE('',#21789,#21791,#5845,.T.); -#26072=EDGE_CURVE('',#21791,#21793,#5849,.T.); -#26074=EDGE_CURVE('',#21793,#21795,#5853,.T.); -#26076=EDGE_CURVE('',#21795,#21797,#5857,.T.); -#26078=EDGE_CURVE('',#21797,#21799,#5861,.T.); -#26080=EDGE_CURVE('',#21799,#21801,#5865,.T.); -#26082=EDGE_CURVE('',#21801,#21803,#5869,.T.); -#26084=EDGE_CURVE('',#21803,#21805,#5873,.T.); -#26086=EDGE_CURVE('',#21805,#21807,#5877,.T.); -#26088=EDGE_CURVE('',#21807,#21809,#5881,.T.); -#26090=EDGE_CURVE('',#21809,#21811,#5885,.T.); -#26092=EDGE_CURVE('',#21811,#21813,#5889,.T.); -#26094=EDGE_CURVE('',#21813,#21815,#5893,.T.); -#26096=EDGE_CURVE('',#21815,#21817,#5897,.T.); -#26098=EDGE_CURVE('',#21817,#21819,#5901,.T.); -#26100=EDGE_CURVE('',#21819,#21821,#5905,.T.); -#26102=EDGE_CURVE('',#21821,#21823,#5909,.T.); -#26104=EDGE_CURVE('',#21823,#21825,#5913,.T.); -#26106=EDGE_CURVE('',#21825,#21827,#5917,.T.); -#26108=EDGE_CURVE('',#21827,#21829,#5921,.T.); -#26110=EDGE_CURVE('',#21829,#21831,#5925,.T.); -#26112=EDGE_CURVE('',#21831,#21833,#5929,.T.); -#26114=EDGE_CURVE('',#21833,#21835,#5933,.T.); -#26116=EDGE_CURVE('',#21835,#21837,#5937,.T.); -#26118=EDGE_CURVE('',#21837,#21839,#5941,.T.); -#26120=EDGE_CURVE('',#21839,#21841,#5945,.T.); -#26122=EDGE_CURVE('',#21841,#21843,#5949,.T.); -#26124=EDGE_CURVE('',#21843,#21845,#5953,.T.); -#26126=EDGE_CURVE('',#21845,#21847,#5957,.T.); -#26128=EDGE_CURVE('',#21847,#21849,#5961,.T.); -#26130=EDGE_CURVE('',#21849,#21851,#5965,.T.); -#26132=EDGE_CURVE('',#21851,#21853,#5969,.T.); -#26134=EDGE_CURVE('',#21853,#21855,#5973,.T.); -#26136=EDGE_CURVE('',#21855,#21857,#5977,.T.); -#26138=EDGE_CURVE('',#21857,#21859,#5981,.T.); -#26140=EDGE_CURVE('',#21859,#21861,#5985,.T.); -#26142=EDGE_CURVE('',#21861,#21863,#5989,.T.); -#26144=EDGE_CURVE('',#21863,#21865,#5993,.T.); -#26146=EDGE_CURVE('',#21865,#21867,#5997,.T.); -#26148=EDGE_CURVE('',#21867,#21756,#6001,.T.); -#26152=EDGE_CURVE('',#21870,#21871,#6005,.T.); -#26154=EDGE_CURVE('',#21871,#21873,#6009,.T.); -#26156=EDGE_CURVE('',#21873,#21875,#6013,.T.); -#26158=EDGE_CURVE('',#21875,#21877,#6017,.T.); -#26160=EDGE_CURVE('',#21877,#21879,#6021,.T.); -#26162=EDGE_CURVE('',#21879,#21881,#6025,.T.); -#26164=EDGE_CURVE('',#21881,#21883,#6029,.T.); -#26166=EDGE_CURVE('',#21883,#21885,#6033,.T.); -#26168=EDGE_CURVE('',#21885,#21887,#6037,.T.); -#26170=EDGE_CURVE('',#21887,#21889,#6041,.T.); -#26172=EDGE_CURVE('',#21889,#21891,#6045,.T.); -#26174=EDGE_CURVE('',#21891,#21893,#6049,.T.); -#26176=EDGE_CURVE('',#21893,#21895,#6053,.T.); -#26178=EDGE_CURVE('',#21895,#21897,#6057,.T.); -#26180=EDGE_CURVE('',#21897,#21899,#6061,.T.); -#26182=EDGE_CURVE('',#21899,#21901,#6065,.T.); -#26184=EDGE_CURVE('',#21901,#21903,#6069,.T.); -#26186=EDGE_CURVE('',#21903,#21905,#6073,.T.); -#26188=EDGE_CURVE('',#21905,#21907,#6077,.T.); -#26190=EDGE_CURVE('',#21907,#21909,#6081,.T.); -#26192=EDGE_CURVE('',#21909,#21911,#6085,.T.); -#26194=EDGE_CURVE('',#21911,#21913,#6089,.T.); -#26196=EDGE_CURVE('',#21913,#21915,#6093,.T.); -#26198=EDGE_CURVE('',#21915,#21917,#6097,.T.); -#26200=EDGE_CURVE('',#21917,#21919,#6101,.T.); -#26202=EDGE_CURVE('',#21919,#21921,#6105,.T.); -#26204=EDGE_CURVE('',#21921,#21923,#6109,.T.); -#26206=EDGE_CURVE('',#21923,#21870,#6113,.T.); -#26210=EDGE_CURVE('',#22032,#22033,#6117,.T.); -#26212=EDGE_CURVE('',#22033,#22034,#6124,.T.); -#26214=EDGE_CURVE('',#22034,#22035,#6131,.T.); -#26216=EDGE_CURVE('',#22032,#22035,#6136,.T.); -#26220=EDGE_CURVE('',#22036,#22037,#6150,.T.); -#26222=EDGE_CURVE('',#22037,#22036,#6154,.T.); -#26226=EDGE_CURVE('',#22042,#22043,#6193,.T.); -#26228=EDGE_CURVE('',#22042,#22045,#6197,.T.); -#26230=EDGE_CURVE('',#22046,#22045,#6202,.T.); -#26232=EDGE_CURVE('',#22046,#22048,#6206,.T.); -#26234=EDGE_CURVE('',#22049,#22048,#6211,.T.); -#26236=EDGE_CURVE('',#22049,#22051,#6215,.T.); -#26238=EDGE_CURVE('',#22051,#22053,#6219,.T.); -#26240=EDGE_CURVE('',#22054,#22053,#6224,.T.); -#26242=EDGE_CURVE('',#22054,#22056,#6228,.T.); -#26244=EDGE_CURVE('',#22043,#22056,#6233,.T.); -#26248=EDGE_CURVE('',#22063,#22064,#6251,.T.); -#26250=EDGE_CURVE('',#22065,#22064,#6256,.T.); -#26252=EDGE_CURVE('',#22065,#22067,#6260,.T.); -#26254=EDGE_CURVE('',#22068,#22067,#6265,.T.); -#26256=EDGE_CURVE('',#22068,#22070,#6269,.T.); -#26258=EDGE_CURVE('',#22071,#22070,#6274,.T.); -#26260=EDGE_CURVE('',#22071,#22073,#6278,.T.); -#26262=EDGE_CURVE('',#22063,#22073,#6283,.T.); -#26266=EDGE_CURVE('',#22076,#22077,#6287,.T.); -#26268=EDGE_CURVE('',#22078,#22077,#6292,.T.); -#26270=EDGE_CURVE('',#22078,#22080,#6296,.T.); -#26272=EDGE_CURVE('',#22081,#22080,#6301,.T.); -#26274=EDGE_CURVE('',#22081,#22083,#6305,.T.); -#26276=EDGE_CURVE('',#22084,#22083,#6310,.T.); -#26278=EDGE_CURVE('',#22084,#22086,#6314,.T.); -#26280=EDGE_CURVE('',#22087,#22086,#6319,.T.); -#26282=EDGE_CURVE('',#22087,#22089,#6323,.T.); -#26284=EDGE_CURVE('',#22076,#22089,#6328,.T.); -#26288=EDGE_CURVE('',#22090,#22091,#6335,.T.); -#26290=EDGE_CURVE('',#22091,#22093,#6339,.T.); -#26292=EDGE_CURVE('',#22094,#22093,#6344,.T.); -#26294=EDGE_CURVE('',#22094,#22096,#6348,.T.); -#26296=EDGE_CURVE('',#22096,#22097,#6361,.T.); -#26298=EDGE_CURVE('',#22097,#22099,#6365,.T.); -#26300=EDGE_CURVE('',#22100,#22099,#6370,.T.); -#26302=EDGE_CURVE('',#22100,#22102,#6374,.T.); -#26304=EDGE_CURVE('',#22103,#22102,#6379,.T.); -#26306=EDGE_CURVE('',#22103,#22105,#6383,.T.); -#26308=EDGE_CURVE('',#22106,#22105,#6388,.T.); -#26310=EDGE_CURVE('',#22106,#22108,#6392,.T.); -#26312=EDGE_CURVE('',#22108,#22109,#6436,.T.); -#26314=EDGE_CURVE('',#22109,#22111,#6440,.T.); -#26316=EDGE_CURVE('',#22111,#22112,#6460,.T.); -#26318=EDGE_CURVE('',#22112,#22113,#6467,.T.); -#26320=EDGE_CURVE('',#22113,#22115,#6471,.T.); -#26322=EDGE_CURVE('',#22116,#22115,#6476,.T.); -#26324=EDGE_CURVE('',#22116,#22090,#6480,.T.); -#26328=ADVANCED_FACE('',(#24579,#24619,#24637,#24707,#24823,#24881,#24907, -#24929,#25011,#25093,#25103,#25133,#25143,#25153,#25179,#25249,#25277,#25317, -#25335,#25405,#25521,#25579,#25589,#25671,#25681,#25711,#25721,#25731,#25755, -#25771,#25825,#25879,#25897,#25907,#25947,#25965,#26035,#26151,#26209,#26219, -#26225,#26247,#26265,#26287,#26327),#24572,.T.); -#26334=EDGE_CURVE('',#18004,#18005,#2069,.T.); -#26336=EDGE_CURVE('',#18005,#18007,#2073,.T.); -#26338=EDGE_CURVE('',#18007,#18009,#2077,.T.); -#26340=EDGE_CURVE('',#18009,#18011,#2081,.T.); -#26342=EDGE_CURVE('',#18011,#18013,#2085,.T.); -#26344=EDGE_CURVE('',#18013,#18015,#2089,.T.); -#26346=EDGE_CURVE('',#18015,#18017,#2093,.T.); -#26348=EDGE_CURVE('',#18017,#18019,#2097,.T.); -#26350=EDGE_CURVE('',#18019,#18021,#2101,.T.); -#26352=EDGE_CURVE('',#18021,#18004,#2105,.T.); -#26356=ADVANCED_FACE('',(#26355),#26333,.T.); -#26362=EDGE_CURVE('',#18024,#18025,#2109,.T.); -#26364=EDGE_CURVE('',#18025,#18027,#2113,.T.); -#26366=EDGE_CURVE('',#18027,#18029,#2117,.T.); -#26368=EDGE_CURVE('',#18029,#18031,#2121,.T.); -#26370=EDGE_CURVE('',#18031,#18033,#2125,.T.); -#26372=EDGE_CURVE('',#18033,#18035,#2129,.T.); -#26374=EDGE_CURVE('',#18035,#18037,#2133,.T.); -#26376=EDGE_CURVE('',#18037,#18039,#2137,.T.); -#26378=EDGE_CURVE('',#18039,#18041,#2141,.T.); -#26380=EDGE_CURVE('',#18041,#18024,#2145,.T.); -#26384=ADVANCED_FACE('',(#26383),#26361,.T.); -#26390=EDGE_CURVE('',#18128,#18129,#2317,.T.); -#26392=EDGE_CURVE('',#18129,#18131,#2321,.T.); -#26394=EDGE_CURVE('',#18131,#18133,#2325,.T.); -#26396=EDGE_CURVE('',#18133,#18135,#2329,.T.); -#26398=EDGE_CURVE('',#18135,#18137,#2333,.T.); -#26400=EDGE_CURVE('',#18137,#18139,#2337,.T.); -#26402=EDGE_CURVE('',#18139,#18141,#2341,.T.); -#26404=EDGE_CURVE('',#18141,#18143,#2345,.T.); -#26406=EDGE_CURVE('',#18143,#18145,#2349,.T.); -#26408=EDGE_CURVE('',#18145,#18147,#2353,.T.); -#26410=EDGE_CURVE('',#18147,#18149,#2357,.T.); -#26412=EDGE_CURVE('',#18149,#18151,#2361,.T.); -#26414=EDGE_CURVE('',#18151,#18153,#2365,.T.); -#26416=EDGE_CURVE('',#18153,#18155,#2369,.T.); -#26418=EDGE_CURVE('',#18155,#18157,#2373,.T.); -#26420=EDGE_CURVE('',#18157,#18128,#2377,.T.); -#26424=ADVANCED_FACE('',(#26423),#26389,.T.); -#26430=EDGE_CURVE('',#18160,#18161,#2381,.T.); -#26432=EDGE_CURVE('',#18161,#18163,#2385,.T.); -#26434=EDGE_CURVE('',#18163,#18165,#2389,.T.); -#26436=EDGE_CURVE('',#18165,#18167,#2393,.T.); -#26438=EDGE_CURVE('',#18167,#18169,#2397,.T.); -#26440=EDGE_CURVE('',#18169,#18171,#2401,.T.); -#26442=EDGE_CURVE('',#18171,#18173,#2405,.T.); -#26444=EDGE_CURVE('',#18173,#18175,#2409,.T.); -#26446=EDGE_CURVE('',#18175,#18177,#2413,.T.); -#26448=EDGE_CURVE('',#18177,#18179,#2417,.T.); -#26450=EDGE_CURVE('',#18179,#18181,#2421,.T.); -#26452=EDGE_CURVE('',#18181,#18183,#2425,.T.); -#26454=EDGE_CURVE('',#18183,#18185,#2429,.T.); -#26456=EDGE_CURVE('',#18185,#18187,#2433,.T.); -#26458=EDGE_CURVE('',#18187,#18189,#2437,.T.); -#26460=EDGE_CURVE('',#18189,#18160,#2441,.T.); -#26464=ADVANCED_FACE('',(#26463),#26429,.T.); -#26470=EDGE_CURVE('',#20500,#20501,#3265,.T.); -#26472=EDGE_CURVE('',#20501,#20503,#3269,.T.); -#26474=EDGE_CURVE('',#20503,#20505,#3273,.T.); -#26476=EDGE_CURVE('',#20505,#20507,#3277,.T.); -#26478=EDGE_CURVE('',#20507,#20509,#3281,.T.); -#26480=EDGE_CURVE('',#20509,#20511,#3285,.T.); -#26482=EDGE_CURVE('',#20511,#20513,#3289,.T.); -#26484=EDGE_CURVE('',#20513,#20515,#3293,.T.); -#26486=EDGE_CURVE('',#20515,#20517,#3297,.T.); -#26488=EDGE_CURVE('',#20517,#20519,#3301,.T.); -#26490=EDGE_CURVE('',#20519,#20521,#3305,.T.); -#26492=EDGE_CURVE('',#20521,#20500,#3309,.T.); -#26496=ADVANCED_FACE('',(#26495),#26469,.T.); -#26502=EDGE_CURVE('',#20632,#20633,#3529,.T.); -#26504=EDGE_CURVE('',#20633,#20635,#3533,.T.); -#26506=EDGE_CURVE('',#20635,#20637,#3537,.T.); -#26508=EDGE_CURVE('',#20637,#20639,#3541,.T.); -#26510=EDGE_CURVE('',#20639,#20641,#3545,.T.); -#26512=EDGE_CURVE('',#20641,#20643,#3549,.T.); -#26514=EDGE_CURVE('',#20643,#20645,#3553,.T.); -#26516=EDGE_CURVE('',#20645,#20647,#3557,.T.); -#26518=EDGE_CURVE('',#20647,#20649,#3561,.T.); -#26520=EDGE_CURVE('',#20649,#20651,#3565,.T.); -#26522=EDGE_CURVE('',#20651,#20653,#3569,.T.); -#26524=EDGE_CURVE('',#20653,#20655,#3573,.T.); -#26526=EDGE_CURVE('',#20655,#20657,#3577,.T.); -#26528=EDGE_CURVE('',#20657,#20659,#3581,.T.); -#26530=EDGE_CURVE('',#20659,#20661,#3585,.T.); -#26532=EDGE_CURVE('',#20661,#20632,#3589,.T.); -#26536=ADVANCED_FACE('',(#26535),#26501,.T.); -#26542=EDGE_CURVE('',#20664,#20665,#3593,.T.); -#26544=EDGE_CURVE('',#20665,#20667,#3597,.T.); -#26546=EDGE_CURVE('',#20667,#20669,#3601,.T.); -#26548=EDGE_CURVE('',#20669,#20671,#3605,.T.); -#26550=EDGE_CURVE('',#20671,#20673,#3609,.T.); -#26552=EDGE_CURVE('',#20673,#20675,#3613,.T.); -#26554=EDGE_CURVE('',#20675,#20677,#3617,.T.); -#26556=EDGE_CURVE('',#20677,#20679,#3621,.T.); -#26558=EDGE_CURVE('',#20679,#20681,#3625,.T.); -#26560=EDGE_CURVE('',#20681,#20683,#3629,.T.); -#26562=EDGE_CURVE('',#20683,#20685,#3633,.T.); -#26564=EDGE_CURVE('',#20685,#20687,#3637,.T.); -#26566=EDGE_CURVE('',#20687,#20689,#3641,.T.); -#26568=EDGE_CURVE('',#20689,#20691,#3645,.T.); -#26570=EDGE_CURVE('',#20691,#20693,#3649,.T.); -#26572=EDGE_CURVE('',#20693,#20664,#3653,.T.); -#26576=ADVANCED_FACE('',(#26575),#26541,.T.); -#26582=EDGE_CURVE('',#20760,#20761,#3785,.T.); -#26584=EDGE_CURVE('',#20761,#20763,#3789,.T.); -#26586=EDGE_CURVE('',#20763,#20765,#3793,.T.); -#26588=EDGE_CURVE('',#20765,#20767,#3797,.T.); -#26590=EDGE_CURVE('',#20767,#20769,#3801,.T.); -#26592=EDGE_CURVE('',#20769,#20771,#3805,.T.); -#26594=EDGE_CURVE('',#20771,#20773,#3809,.T.); -#26596=EDGE_CURVE('',#20773,#20775,#3813,.T.); -#26598=EDGE_CURVE('',#20775,#20777,#3817,.T.); -#26600=EDGE_CURVE('',#20777,#20760,#3821,.T.); -#26604=ADVANCED_FACE('',(#26603),#26581,.T.); -#26610=EDGE_CURVE('',#20780,#20781,#3825,.T.); -#26612=EDGE_CURVE('',#20781,#20783,#3829,.T.); -#26614=EDGE_CURVE('',#20783,#20785,#3833,.T.); -#26616=EDGE_CURVE('',#20785,#20787,#3837,.T.); -#26618=EDGE_CURVE('',#20787,#20789,#3841,.T.); -#26620=EDGE_CURVE('',#20789,#20791,#3845,.T.); -#26622=EDGE_CURVE('',#20791,#20793,#3849,.T.); -#26624=EDGE_CURVE('',#20793,#20795,#3853,.T.); -#26626=EDGE_CURVE('',#20795,#20797,#3857,.T.); -#26628=EDGE_CURVE('',#20797,#20780,#3861,.T.); -#26632=ADVANCED_FACE('',(#26631),#26609,.T.); -#26638=EDGE_CURVE('',#20884,#20885,#4033,.T.); -#26640=EDGE_CURVE('',#20885,#20887,#4037,.T.); -#26642=EDGE_CURVE('',#20887,#20889,#4041,.T.); -#26644=EDGE_CURVE('',#20889,#20891,#4045,.T.); -#26646=EDGE_CURVE('',#20891,#20893,#4049,.T.); -#26648=EDGE_CURVE('',#20893,#20895,#4053,.T.); -#26650=EDGE_CURVE('',#20895,#20897,#4057,.T.); -#26652=EDGE_CURVE('',#20897,#20899,#4061,.T.); -#26654=EDGE_CURVE('',#20899,#20901,#4065,.T.); -#26656=EDGE_CURVE('',#20901,#20903,#4069,.T.); -#26658=EDGE_CURVE('',#20903,#20905,#4073,.T.); -#26660=EDGE_CURVE('',#20905,#20907,#4077,.T.); -#26662=EDGE_CURVE('',#20907,#20909,#4081,.T.); -#26664=EDGE_CURVE('',#20909,#20911,#4085,.T.); -#26666=EDGE_CURVE('',#20911,#20913,#4089,.T.); -#26668=EDGE_CURVE('',#20913,#20884,#4093,.T.); -#26672=ADVANCED_FACE('',(#26671),#26637,.T.); -#26678=EDGE_CURVE('',#20916,#20917,#4097,.T.); -#26680=EDGE_CURVE('',#20917,#20919,#4101,.T.); -#26682=EDGE_CURVE('',#20919,#20921,#4105,.T.); -#26684=EDGE_CURVE('',#20921,#20923,#4109,.T.); -#26686=EDGE_CURVE('',#20923,#20925,#4113,.T.); -#26688=EDGE_CURVE('',#20925,#20927,#4117,.T.); -#26690=EDGE_CURVE('',#20927,#20929,#4121,.T.); -#26692=EDGE_CURVE('',#20929,#20931,#4125,.T.); -#26694=EDGE_CURVE('',#20931,#20933,#4129,.T.); -#26696=EDGE_CURVE('',#20933,#20935,#4133,.T.); -#26698=EDGE_CURVE('',#20935,#20937,#4137,.T.); -#26700=EDGE_CURVE('',#20937,#20939,#4141,.T.); -#26702=EDGE_CURVE('',#20939,#20941,#4145,.T.); -#26704=EDGE_CURVE('',#20941,#20943,#4149,.T.); -#26706=EDGE_CURVE('',#20943,#20945,#4153,.T.); -#26708=EDGE_CURVE('',#20945,#20916,#4157,.T.); -#26712=ADVANCED_FACE('',(#26711),#26677,.T.); -#26718=EDGE_CURVE('',#21242,#21243,#4749,.T.); -#26720=EDGE_CURVE('',#21243,#21245,#4753,.T.); -#26722=EDGE_CURVE('',#21245,#21247,#4757,.T.); -#26724=EDGE_CURVE('',#21247,#21249,#4761,.T.); -#26726=EDGE_CURVE('',#21249,#21251,#4765,.T.); -#26728=EDGE_CURVE('',#21251,#21253,#4769,.T.); -#26730=EDGE_CURVE('',#21253,#21255,#4773,.T.); -#26732=EDGE_CURVE('',#21255,#21257,#4777,.T.); -#26734=EDGE_CURVE('',#21257,#21259,#4781,.T.); -#26736=EDGE_CURVE('',#21259,#21261,#4785,.T.); -#26738=EDGE_CURVE('',#21261,#21263,#4789,.T.); -#26740=EDGE_CURVE('',#21263,#21242,#4793,.T.); -#26744=ADVANCED_FACE('',(#26743),#26717,.T.); -#26750=EDGE_CURVE('',#21304,#21305,#4873,.T.); -#26752=EDGE_CURVE('',#21305,#21307,#4877,.T.); -#26754=EDGE_CURVE('',#21307,#21304,#4881,.T.); -#26758=ADVANCED_FACE('',(#26757),#26749,.T.); -#26764=EDGE_CURVE('',#21376,#21377,#5017,.T.); -#26766=EDGE_CURVE('',#21377,#21379,#5021,.T.); -#26768=EDGE_CURVE('',#21379,#21381,#5025,.T.); -#26770=EDGE_CURVE('',#21381,#21383,#5029,.T.); -#26772=EDGE_CURVE('',#21383,#21385,#5033,.T.); -#26774=EDGE_CURVE('',#21385,#21387,#5037,.T.); -#26776=EDGE_CURVE('',#21387,#21389,#5041,.T.); -#26778=EDGE_CURVE('',#21389,#21391,#5045,.T.); -#26780=EDGE_CURVE('',#21391,#21393,#5049,.T.); -#26782=EDGE_CURVE('',#21393,#21395,#5053,.T.); -#26784=EDGE_CURVE('',#21395,#21397,#5057,.T.); -#26786=EDGE_CURVE('',#21397,#21399,#5061,.T.); -#26788=EDGE_CURVE('',#21399,#21401,#5065,.T.); -#26790=EDGE_CURVE('',#21401,#21403,#5069,.T.); -#26792=EDGE_CURVE('',#21403,#21405,#5073,.T.); -#26794=EDGE_CURVE('',#21405,#21407,#5077,.T.); -#26796=EDGE_CURVE('',#21407,#21409,#5081,.T.); -#26798=EDGE_CURVE('',#21409,#21376,#5085,.T.); -#26802=ADVANCED_FACE('',(#26801),#26763,.T.); -#26808=EDGE_CURVE('',#21464,#21465,#5193,.T.); -#26810=EDGE_CURVE('',#21465,#21467,#5197,.T.); -#26812=EDGE_CURVE('',#21467,#21469,#5201,.T.); -#26814=EDGE_CURVE('',#21469,#21471,#5205,.T.); -#26816=EDGE_CURVE('',#21471,#21473,#5209,.T.); -#26818=EDGE_CURVE('',#21473,#21475,#5213,.T.); -#26820=EDGE_CURVE('',#21475,#21477,#5217,.T.); -#26822=EDGE_CURVE('',#21477,#21479,#5221,.T.); -#26824=EDGE_CURVE('',#21479,#21481,#5225,.T.); -#26826=EDGE_CURVE('',#21481,#21483,#5229,.T.); -#26828=EDGE_CURVE('',#21483,#21485,#5233,.T.); -#26830=EDGE_CURVE('',#21485,#21487,#5237,.T.); -#26832=EDGE_CURVE('',#21487,#21489,#5241,.T.); -#26834=EDGE_CURVE('',#21489,#21491,#5245,.T.); -#26836=EDGE_CURVE('',#21491,#21493,#5249,.T.); -#26838=EDGE_CURVE('',#21493,#21495,#5253,.T.); -#26840=EDGE_CURVE('',#21495,#21497,#5257,.T.); -#26842=EDGE_CURVE('',#21497,#21464,#5261,.T.); -#26846=ADVANCED_FACE('',(#26845),#26807,.T.); -#26852=EDGE_CURVE('',#21516,#21517,#5297,.T.); -#26854=EDGE_CURVE('',#21517,#21519,#5301,.T.); -#26856=EDGE_CURVE('',#21519,#21516,#5305,.T.); -#26860=ADVANCED_FACE('',(#26859),#26851,.T.); -#26866=EDGE_CURVE('',#21568,#21569,#5401,.T.); -#26868=EDGE_CURVE('',#21569,#21571,#5405,.T.); -#26870=EDGE_CURVE('',#21571,#21573,#5409,.T.); -#26872=EDGE_CURVE('',#21573,#21575,#5413,.T.); -#26874=EDGE_CURVE('',#21575,#21577,#5417,.T.); -#26876=EDGE_CURVE('',#21577,#21579,#5421,.T.); -#26878=EDGE_CURVE('',#21579,#21581,#5425,.T.); -#26880=EDGE_CURVE('',#21581,#21583,#5429,.T.); -#26882=EDGE_CURVE('',#21583,#21585,#5433,.T.); -#26884=EDGE_CURVE('',#21585,#21568,#5437,.T.); -#26888=ADVANCED_FACE('',(#26887),#26865,.T.); -#26894=EDGE_CURVE('',#21588,#21589,#5441,.T.); -#26896=EDGE_CURVE('',#21589,#21591,#5445,.T.); -#26898=EDGE_CURVE('',#21591,#21593,#5449,.T.); -#26900=EDGE_CURVE('',#21593,#21595,#5453,.T.); -#26902=EDGE_CURVE('',#21595,#21597,#5457,.T.); -#26904=EDGE_CURVE('',#21597,#21599,#5461,.T.); -#26906=EDGE_CURVE('',#21599,#21601,#5465,.T.); -#26908=EDGE_CURVE('',#21601,#21603,#5469,.T.); -#26910=EDGE_CURVE('',#21603,#21605,#5473,.T.); -#26912=EDGE_CURVE('',#21605,#21588,#5477,.T.); -#26916=ADVANCED_FACE('',(#26915),#26893,.T.); -#26922=EDGE_CURVE('',#21692,#21693,#5649,.T.); -#26924=EDGE_CURVE('',#21693,#21695,#5653,.T.); -#26926=EDGE_CURVE('',#21695,#21697,#5657,.T.); -#26928=EDGE_CURVE('',#21697,#21699,#5661,.T.); -#26930=EDGE_CURVE('',#21699,#21701,#5665,.T.); -#26932=EDGE_CURVE('',#21701,#21703,#5669,.T.); -#26934=EDGE_CURVE('',#21703,#21705,#5673,.T.); -#26936=EDGE_CURVE('',#21705,#21707,#5677,.T.); -#26938=EDGE_CURVE('',#21707,#21709,#5681,.T.); -#26940=EDGE_CURVE('',#21709,#21711,#5685,.T.); -#26942=EDGE_CURVE('',#21711,#21713,#5689,.T.); -#26944=EDGE_CURVE('',#21713,#21715,#5693,.T.); -#26946=EDGE_CURVE('',#21715,#21717,#5697,.T.); -#26948=EDGE_CURVE('',#21717,#21719,#5701,.T.); -#26950=EDGE_CURVE('',#21719,#21721,#5705,.T.); -#26952=EDGE_CURVE('',#21721,#21692,#5709,.T.); -#26956=ADVANCED_FACE('',(#26955),#26921,.T.); -#26962=EDGE_CURVE('',#21724,#21725,#5713,.T.); -#26964=EDGE_CURVE('',#21725,#21727,#5717,.T.); -#26966=EDGE_CURVE('',#21727,#21729,#5721,.T.); -#26968=EDGE_CURVE('',#21729,#21731,#5725,.T.); -#26970=EDGE_CURVE('',#21731,#21733,#5729,.T.); -#26972=EDGE_CURVE('',#21733,#21735,#5733,.T.); -#26974=EDGE_CURVE('',#21735,#21737,#5737,.T.); -#26976=EDGE_CURVE('',#21737,#21739,#5741,.T.); -#26978=EDGE_CURVE('',#21739,#21741,#5745,.T.); -#26980=EDGE_CURVE('',#21741,#21743,#5749,.T.); -#26982=EDGE_CURVE('',#21743,#21745,#5753,.T.); -#26984=EDGE_CURVE('',#21745,#21747,#5757,.T.); -#26986=EDGE_CURVE('',#21747,#21749,#5761,.T.); -#26988=EDGE_CURVE('',#21749,#21751,#5765,.T.); -#26990=EDGE_CURVE('',#21751,#21753,#5769,.T.); -#26992=EDGE_CURVE('',#21753,#21724,#5773,.T.); -#26996=ADVANCED_FACE('',(#26995),#26961,.T.); -#27002=EDGE_CURVE('',#22038,#22039,#6177,.T.); -#27004=EDGE_CURVE('',#22039,#22041,#6181,.T.); -#27006=EDGE_CURVE('',#22041,#22038,#6188,.T.); -#27010=ADVANCED_FACE('',(#27009),#27001,.T.); -#27016=EDGE_CURVE('',#22057,#22058,#6238,.T.); -#27018=EDGE_CURVE('',#22057,#22060,#6242,.T.); -#27020=EDGE_CURVE('',#22058,#22060,#6247,.T.); -#27024=ADVANCED_FACE('',(#27023),#27015,.T.); -#27030=EDGE_CURVE('',#22119,#22120,#6484,.T.); -#27032=EDGE_CURVE('',#22121,#22120,#6489,.T.); -#27034=EDGE_CURVE('',#22121,#22123,#6493,.T.); -#27036=EDGE_CURVE('',#22124,#22123,#6498,.T.); -#27038=EDGE_CURVE('',#22124,#22126,#6502,.T.); -#27040=EDGE_CURVE('',#22127,#22126,#6507,.T.); -#27042=EDGE_CURVE('',#22127,#22129,#6511,.T.); -#27044=EDGE_CURVE('',#22130,#22129,#6516,.T.); -#27046=EDGE_CURVE('',#22130,#22132,#6520,.T.); -#27048=EDGE_CURVE('',#22133,#22132,#6525,.T.); -#27050=EDGE_CURVE('',#22133,#22135,#6529,.T.); -#27052=EDGE_CURVE('',#22119,#22135,#6534,.T.); -#27056=ADVANCED_FACE('',(#27055),#27029,.T.); -#27063=EDGE_CURVE('',#16923,#16920,#6542,.T.); -#27070=EDGE_CURVE('',#16925,#16921,#6550,.T.); -#27074=ADVANCED_FACE('',(#27073),#27061,.T.); -#27082=EDGE_CURVE('',#16867,#16885,#6554,.T.); -#27087=ADVANCED_FACE('',(#27086),#27079,.F.); -#27096=EDGE_CURVE('',#16849,#16865,#6558,.T.); -#27100=ADVANCED_FACE('',(#27099),#27092,.F.); -#27109=EDGE_CURVE('',#16848,#16864,#6562,.T.); -#27113=ADVANCED_FACE('',(#27112),#27105,.F.); -#27125=ADVANCED_FACE('',(#27124),#27118,.F.); -#27133=EDGE_CURVE('',#16836,#16852,#6566,.T.); -#27138=ADVANCED_FACE('',(#27137),#27130,.F.); -#27145=EDGE_CURVE('',#16837,#16853,#6570,.T.); -#27151=ADVANCED_FACE('',(#27150),#27143,.F.); -#27158=EDGE_CURVE('',#16869,#16887,#6574,.T.); -#27164=ADVANCED_FACE('',(#27163),#27156,.F.); -#27176=ADVANCED_FACE('',(#27175),#27169,.F.); -#27183=EDGE_CURVE('',#17966,#17546,#6578,.T.); -#27185=EDGE_CURVE('',#17546,#17547,#6654,.T.); -#27187=EDGE_CURVE('',#17967,#17547,#6650,.T.); -#27191=ADVANCED_FACE('',(#27190),#27181,.F.); -#27198=EDGE_CURVE('',#18001,#17581,#6582,.T.); -#27200=EDGE_CURVE('',#17581,#17546,#6658,.T.); -#27205=ADVANCED_FACE('',(#27204),#27196,.F.); -#27212=EDGE_CURVE('',#17999,#17579,#6586,.T.); -#27214=EDGE_CURVE('',#17579,#17581,#6662,.T.); -#27219=ADVANCED_FACE('',(#27218),#27210,.F.); -#27226=EDGE_CURVE('',#17997,#17577,#6590,.T.); -#27228=EDGE_CURVE('',#17577,#17579,#6666,.T.); -#27233=ADVANCED_FACE('',(#27232),#27224,.F.); -#27240=EDGE_CURVE('',#17995,#17575,#6594,.T.); -#27242=EDGE_CURVE('',#17575,#17577,#6670,.T.); -#27247=ADVANCED_FACE('',(#27246),#27238,.F.); -#27254=EDGE_CURVE('',#17993,#17573,#6598,.T.); -#27256=EDGE_CURVE('',#17573,#17575,#6674,.T.); -#27261=ADVANCED_FACE('',(#27260),#27252,.F.); -#27268=EDGE_CURVE('',#17991,#17571,#6602,.T.); -#27270=EDGE_CURVE('',#17571,#17573,#6678,.T.); -#27275=ADVANCED_FACE('',(#27274),#27266,.F.); -#27282=EDGE_CURVE('',#17989,#17569,#6606,.T.); -#27284=EDGE_CURVE('',#17569,#17571,#6682,.T.); -#27289=ADVANCED_FACE('',(#27288),#27280,.F.); -#27296=EDGE_CURVE('',#17987,#17567,#6610,.T.); -#27298=EDGE_CURVE('',#17567,#17569,#6686,.T.); -#27303=ADVANCED_FACE('',(#27302),#27294,.F.); -#27310=EDGE_CURVE('',#17985,#17565,#6614,.T.); -#27312=EDGE_CURVE('',#17565,#17567,#6690,.T.); -#27317=ADVANCED_FACE('',(#27316),#27308,.F.); -#27324=EDGE_CURVE('',#17983,#17563,#6618,.T.); -#27326=EDGE_CURVE('',#17563,#17565,#6694,.T.); -#27331=ADVANCED_FACE('',(#27330),#27322,.F.); -#27338=EDGE_CURVE('',#17981,#17561,#6622,.T.); -#27340=EDGE_CURVE('',#17561,#17563,#6698,.T.); -#27345=ADVANCED_FACE('',(#27344),#27336,.F.); -#27352=EDGE_CURVE('',#17979,#17559,#6626,.T.); -#27354=EDGE_CURVE('',#17559,#17561,#6702,.T.); -#27359=ADVANCED_FACE('',(#27358),#27350,.F.); -#27366=EDGE_CURVE('',#17977,#17557,#6630,.T.); -#27368=EDGE_CURVE('',#17557,#17559,#6706,.T.); -#27373=ADVANCED_FACE('',(#27372),#27364,.F.); -#27380=EDGE_CURVE('',#17975,#17555,#6634,.T.); -#27382=EDGE_CURVE('',#17555,#17557,#6710,.T.); -#27387=ADVANCED_FACE('',(#27386),#27378,.F.); -#27394=EDGE_CURVE('',#17973,#17553,#6638,.T.); -#27396=EDGE_CURVE('',#17553,#17555,#6714,.T.); -#27401=ADVANCED_FACE('',(#27400),#27392,.F.); -#27408=EDGE_CURVE('',#17971,#17551,#6642,.T.); -#27410=EDGE_CURVE('',#17551,#17553,#6718,.T.); -#27415=ADVANCED_FACE('',(#27414),#27406,.F.); -#27422=EDGE_CURVE('',#17969,#17549,#6646,.T.); -#27424=EDGE_CURVE('',#17549,#17551,#6722,.T.); -#27429=ADVANCED_FACE('',(#27428),#27420,.F.); -#27437=EDGE_CURVE('',#17547,#17549,#6726,.T.); -#27442=ADVANCED_FACE('',(#27441),#27434,.F.); -#27469=EDGE_CURVE('',#17584,#17585,#6730,.T.); -#27471=EDGE_CURVE('',#17601,#17584,#6734,.T.); -#27473=EDGE_CURVE('',#17599,#17601,#6738,.T.); -#27475=EDGE_CURVE('',#17597,#17599,#6742,.T.); -#27477=EDGE_CURVE('',#17595,#17597,#6746,.T.); -#27479=EDGE_CURVE('',#17593,#17595,#6750,.T.); -#27481=EDGE_CURVE('',#17591,#17593,#6754,.T.); -#27483=EDGE_CURVE('',#17589,#17591,#6758,.T.); -#27485=EDGE_CURVE('',#17587,#17589,#6762,.T.); -#27487=EDGE_CURVE('',#17585,#17587,#6766,.T.); -#27491=EDGE_CURVE('',#17604,#17605,#6770,.T.); -#27493=EDGE_CURVE('',#17621,#17604,#6774,.T.); -#27495=EDGE_CURVE('',#17619,#17621,#6778,.T.); -#27497=EDGE_CURVE('',#17617,#17619,#6782,.T.); -#27499=EDGE_CURVE('',#17615,#17617,#6786,.T.); -#27501=EDGE_CURVE('',#17613,#17615,#6790,.T.); -#27503=EDGE_CURVE('',#17611,#17613,#6794,.T.); -#27505=EDGE_CURVE('',#17609,#17611,#6798,.T.); -#27507=EDGE_CURVE('',#17607,#17609,#6802,.T.); -#27509=EDGE_CURVE('',#17605,#17607,#6806,.T.); -#27513=ADVANCED_FACE('',(#27468,#27490,#27512),#27447,.T.); -#27526=EDGE_CURVE('',#17624,#17625,#6810,.T.); -#27528=EDGE_CURVE('',#17637,#17624,#6814,.T.); -#27530=EDGE_CURVE('',#17635,#17637,#6818,.T.); -#27532=EDGE_CURVE('',#17633,#17635,#6822,.T.); -#27534=EDGE_CURVE('',#17631,#17633,#6826,.T.); -#27536=EDGE_CURVE('',#17629,#17631,#6830,.T.); -#27538=EDGE_CURVE('',#17627,#17629,#6834,.T.); -#27540=EDGE_CURVE('',#17625,#17627,#6838,.T.); -#27544=ADVANCED_FACE('',(#27543),#27525,.T.); -#27557=EDGE_CURVE('',#17640,#17641,#6842,.T.); -#27559=EDGE_CURVE('',#17705,#17640,#6846,.T.); -#27561=EDGE_CURVE('',#17703,#17705,#6850,.T.); -#27563=EDGE_CURVE('',#17701,#17703,#6854,.T.); -#27565=EDGE_CURVE('',#17699,#17701,#6858,.T.); -#27567=EDGE_CURVE('',#17697,#17699,#6862,.T.); -#27569=EDGE_CURVE('',#17695,#17697,#6866,.T.); -#27571=EDGE_CURVE('',#17693,#17695,#6870,.T.); -#27573=EDGE_CURVE('',#17691,#17693,#6874,.T.); -#27575=EDGE_CURVE('',#17689,#17691,#6878,.T.); -#27577=EDGE_CURVE('',#17687,#17689,#6882,.T.); -#27579=EDGE_CURVE('',#17685,#17687,#6886,.T.); -#27581=EDGE_CURVE('',#17683,#17685,#6890,.T.); -#27583=EDGE_CURVE('',#17681,#17683,#6894,.T.); -#27585=EDGE_CURVE('',#17679,#17681,#6898,.T.); -#27587=EDGE_CURVE('',#17677,#17679,#6902,.T.); -#27589=EDGE_CURVE('',#17675,#17677,#6906,.T.); -#27591=EDGE_CURVE('',#17673,#17675,#6910,.T.); -#27593=EDGE_CURVE('',#17671,#17673,#6914,.T.); -#27595=EDGE_CURVE('',#17669,#17671,#6918,.T.); -#27597=EDGE_CURVE('',#17667,#17669,#6922,.T.); -#27599=EDGE_CURVE('',#17665,#17667,#6926,.T.); -#27601=EDGE_CURVE('',#17663,#17665,#6930,.T.); -#27603=EDGE_CURVE('',#17661,#17663,#6934,.T.); -#27605=EDGE_CURVE('',#17659,#17661,#6938,.T.); -#27607=EDGE_CURVE('',#17657,#17659,#6942,.T.); -#27609=EDGE_CURVE('',#17655,#17657,#6946,.T.); -#27611=EDGE_CURVE('',#17653,#17655,#6950,.T.); -#27613=EDGE_CURVE('',#17651,#17653,#6954,.T.); -#27615=EDGE_CURVE('',#17649,#17651,#6958,.T.); -#27617=EDGE_CURVE('',#17647,#17649,#6962,.T.); -#27619=EDGE_CURVE('',#17645,#17647,#6966,.T.); -#27621=EDGE_CURVE('',#17643,#17645,#6970,.T.); -#27623=EDGE_CURVE('',#17641,#17643,#6974,.T.); -#27627=EDGE_CURVE('',#17708,#17709,#6978,.T.); -#27629=EDGE_CURVE('',#17737,#17708,#6982,.T.); -#27631=EDGE_CURVE('',#17735,#17737,#6986,.T.); -#27633=EDGE_CURVE('',#17733,#17735,#6990,.T.); -#27635=EDGE_CURVE('',#17731,#17733,#6994,.T.); -#27637=EDGE_CURVE('',#17729,#17731,#6998,.T.); -#27639=EDGE_CURVE('',#17727,#17729,#7002,.T.); -#27641=EDGE_CURVE('',#17725,#17727,#7006,.T.); -#27643=EDGE_CURVE('',#17723,#17725,#7010,.T.); -#27645=EDGE_CURVE('',#17721,#17723,#7014,.T.); -#27647=EDGE_CURVE('',#17719,#17721,#7018,.T.); -#27649=EDGE_CURVE('',#17717,#17719,#7022,.T.); -#27651=EDGE_CURVE('',#17715,#17717,#7026,.T.); -#27653=EDGE_CURVE('',#17713,#17715,#7030,.T.); -#27655=EDGE_CURVE('',#17711,#17713,#7034,.T.); -#27657=EDGE_CURVE('',#17709,#17711,#7038,.T.); -#27661=EDGE_CURVE('',#17740,#17741,#7042,.T.); -#27663=EDGE_CURVE('',#17769,#17740,#7046,.T.); -#27665=EDGE_CURVE('',#17767,#17769,#7050,.T.); -#27667=EDGE_CURVE('',#17765,#17767,#7054,.T.); -#27669=EDGE_CURVE('',#17763,#17765,#7058,.T.); -#27671=EDGE_CURVE('',#17761,#17763,#7062,.T.); -#27673=EDGE_CURVE('',#17759,#17761,#7066,.T.); -#27675=EDGE_CURVE('',#17757,#17759,#7070,.T.); -#27677=EDGE_CURVE('',#17755,#17757,#7074,.T.); -#27679=EDGE_CURVE('',#17753,#17755,#7078,.T.); -#27681=EDGE_CURVE('',#17751,#17753,#7082,.T.); -#27683=EDGE_CURVE('',#17749,#17751,#7086,.T.); -#27685=EDGE_CURVE('',#17747,#17749,#7090,.T.); -#27687=EDGE_CURVE('',#17745,#17747,#7094,.T.); -#27689=EDGE_CURVE('',#17743,#17745,#7098,.T.); -#27691=EDGE_CURVE('',#17741,#17743,#7102,.T.); -#27695=ADVANCED_FACE('',(#27626,#27660,#27694),#27556,.T.); -#27708=EDGE_CURVE('',#17772,#17773,#7106,.T.); -#27710=EDGE_CURVE('',#17883,#17772,#7110,.T.); -#27712=EDGE_CURVE('',#17881,#17883,#7114,.T.); -#27714=EDGE_CURVE('',#17879,#17881,#7118,.T.); -#27716=EDGE_CURVE('',#17877,#17879,#7122,.T.); -#27718=EDGE_CURVE('',#17875,#17877,#7126,.T.); -#27720=EDGE_CURVE('',#17873,#17875,#7130,.T.); -#27722=EDGE_CURVE('',#17871,#17873,#7134,.T.); -#27724=EDGE_CURVE('',#17869,#17871,#7138,.T.); -#27726=EDGE_CURVE('',#17867,#17869,#7142,.T.); -#27728=EDGE_CURVE('',#17865,#17867,#7146,.T.); -#27730=EDGE_CURVE('',#17863,#17865,#7150,.T.); -#27732=EDGE_CURVE('',#17861,#17863,#7154,.T.); -#27734=EDGE_CURVE('',#17859,#17861,#7158,.T.); -#27736=EDGE_CURVE('',#17857,#17859,#7162,.T.); -#27738=EDGE_CURVE('',#17855,#17857,#7166,.T.); -#27740=EDGE_CURVE('',#17853,#17855,#7170,.T.); -#27742=EDGE_CURVE('',#17851,#17853,#7174,.T.); -#27744=EDGE_CURVE('',#17849,#17851,#7178,.T.); -#27746=EDGE_CURVE('',#17847,#17849,#7182,.T.); -#27748=EDGE_CURVE('',#17845,#17847,#7186,.T.); -#27750=EDGE_CURVE('',#17843,#17845,#7190,.T.); -#27752=EDGE_CURVE('',#17841,#17843,#7194,.T.); -#27754=EDGE_CURVE('',#17839,#17841,#7198,.T.); -#27756=EDGE_CURVE('',#17837,#17839,#7202,.T.); -#27758=EDGE_CURVE('',#17835,#17837,#7206,.T.); -#27760=EDGE_CURVE('',#17833,#17835,#7210,.T.); -#27762=EDGE_CURVE('',#17831,#17833,#7214,.T.); -#27764=EDGE_CURVE('',#17829,#17831,#7218,.T.); -#27766=EDGE_CURVE('',#17827,#17829,#7222,.T.); -#27768=EDGE_CURVE('',#17825,#17827,#7226,.T.); -#27770=EDGE_CURVE('',#17823,#17825,#7230,.T.); -#27772=EDGE_CURVE('',#17821,#17823,#7234,.T.); -#27774=EDGE_CURVE('',#17819,#17821,#7238,.T.); -#27776=EDGE_CURVE('',#17817,#17819,#7242,.T.); -#27778=EDGE_CURVE('',#17815,#17817,#7246,.T.); -#27780=EDGE_CURVE('',#17813,#17815,#7250,.T.); -#27782=EDGE_CURVE('',#17811,#17813,#7254,.T.); -#27784=EDGE_CURVE('',#17809,#17811,#7258,.T.); -#27786=EDGE_CURVE('',#17807,#17809,#7262,.T.); -#27788=EDGE_CURVE('',#17805,#17807,#7266,.T.); -#27790=EDGE_CURVE('',#17803,#17805,#7270,.T.); -#27792=EDGE_CURVE('',#17801,#17803,#7274,.T.); -#27794=EDGE_CURVE('',#17799,#17801,#7278,.T.); -#27796=EDGE_CURVE('',#17797,#17799,#7282,.T.); -#27798=EDGE_CURVE('',#17795,#17797,#7286,.T.); -#27800=EDGE_CURVE('',#17793,#17795,#7290,.T.); -#27802=EDGE_CURVE('',#17791,#17793,#7294,.T.); -#27804=EDGE_CURVE('',#17789,#17791,#7298,.T.); -#27806=EDGE_CURVE('',#17787,#17789,#7302,.T.); -#27808=EDGE_CURVE('',#17785,#17787,#7306,.T.); -#27810=EDGE_CURVE('',#17783,#17785,#7310,.T.); -#27812=EDGE_CURVE('',#17781,#17783,#7314,.T.); -#27814=EDGE_CURVE('',#17779,#17781,#7318,.T.); -#27816=EDGE_CURVE('',#17777,#17779,#7322,.T.); -#27818=EDGE_CURVE('',#17775,#17777,#7326,.T.); -#27820=EDGE_CURVE('',#17773,#17775,#7330,.T.); -#27824=ADVANCED_FACE('',(#27823),#27707,.T.); -#27837=EDGE_CURVE('',#17886,#17887,#7334,.T.); -#27839=EDGE_CURVE('',#17939,#17886,#7338,.T.); -#27841=EDGE_CURVE('',#17937,#17939,#7342,.T.); -#27843=EDGE_CURVE('',#17935,#17937,#7346,.T.); -#27845=EDGE_CURVE('',#17933,#17935,#7350,.T.); -#27847=EDGE_CURVE('',#17931,#17933,#7354,.T.); -#27849=EDGE_CURVE('',#17929,#17931,#7358,.T.); -#27851=EDGE_CURVE('',#17927,#17929,#7362,.T.); -#27853=EDGE_CURVE('',#17925,#17927,#7366,.T.); -#27855=EDGE_CURVE('',#17923,#17925,#7370,.T.); -#27857=EDGE_CURVE('',#17921,#17923,#7374,.T.); -#27859=EDGE_CURVE('',#17919,#17921,#7378,.T.); -#27861=EDGE_CURVE('',#17917,#17919,#7382,.T.); -#27863=EDGE_CURVE('',#17915,#17917,#7386,.T.); -#27865=EDGE_CURVE('',#17913,#17915,#7390,.T.); -#27867=EDGE_CURVE('',#17911,#17913,#7394,.T.); -#27869=EDGE_CURVE('',#17909,#17911,#7398,.T.); -#27871=EDGE_CURVE('',#17907,#17909,#7402,.T.); -#27873=EDGE_CURVE('',#17905,#17907,#7406,.T.); -#27875=EDGE_CURVE('',#17903,#17905,#7410,.T.); -#27877=EDGE_CURVE('',#17901,#17903,#7414,.T.); -#27879=EDGE_CURVE('',#17899,#17901,#7418,.T.); -#27881=EDGE_CURVE('',#17897,#17899,#7422,.T.); -#27883=EDGE_CURVE('',#17895,#17897,#7426,.T.); -#27885=EDGE_CURVE('',#17893,#17895,#7430,.T.); -#27887=EDGE_CURVE('',#17891,#17893,#7434,.T.); -#27889=EDGE_CURVE('',#17889,#17891,#7438,.T.); -#27891=EDGE_CURVE('',#17887,#17889,#7442,.T.); -#27895=ADVANCED_FACE('',(#27894),#27836,.T.); -#27908=EDGE_CURVE('',#17942,#17943,#7446,.T.); -#27910=EDGE_CURVE('',#17963,#17942,#7450,.T.); -#27912=EDGE_CURVE('',#17961,#17963,#7454,.T.); -#27914=EDGE_CURVE('',#17959,#17961,#7458,.T.); -#27916=EDGE_CURVE('',#17957,#17959,#7462,.T.); -#27918=EDGE_CURVE('',#17955,#17957,#7466,.T.); -#27920=EDGE_CURVE('',#17953,#17955,#7470,.T.); -#27922=EDGE_CURVE('',#17951,#17953,#7474,.T.); -#27924=EDGE_CURVE('',#17949,#17951,#7478,.T.); -#27926=EDGE_CURVE('',#17947,#17949,#7482,.T.); -#27928=EDGE_CURVE('',#17945,#17947,#7486,.T.); -#27930=EDGE_CURVE('',#17943,#17945,#7490,.T.); -#27934=ADVANCED_FACE('',(#27933),#27907,.T.); -#27947=EDGE_CURVE('',#18642,#18643,#7494,.T.); -#27949=EDGE_CURVE('',#18659,#18642,#7498,.T.); -#27951=EDGE_CURVE('',#18657,#18659,#7502,.T.); -#27953=EDGE_CURVE('',#18655,#18657,#7506,.T.); -#27955=EDGE_CURVE('',#18653,#18655,#7510,.T.); -#27957=EDGE_CURVE('',#18651,#18653,#7514,.T.); -#27959=EDGE_CURVE('',#18649,#18651,#7518,.T.); -#27961=EDGE_CURVE('',#18647,#18649,#7522,.T.); -#27963=EDGE_CURVE('',#18645,#18647,#7526,.T.); -#27965=EDGE_CURVE('',#18643,#18645,#7530,.T.); -#27969=ADVANCED_FACE('',(#27968),#27946,.T.); -#27982=EDGE_CURVE('',#18662,#18663,#7534,.T.); -#27984=EDGE_CURVE('',#18739,#18662,#7538,.T.); -#27986=EDGE_CURVE('',#18737,#18739,#7542,.T.); -#27988=EDGE_CURVE('',#18735,#18737,#7546,.T.); -#27990=EDGE_CURVE('',#18733,#18735,#7550,.T.); -#27992=EDGE_CURVE('',#18731,#18733,#7554,.T.); -#27994=EDGE_CURVE('',#18729,#18731,#7558,.T.); -#27996=EDGE_CURVE('',#18727,#18729,#7562,.T.); -#27998=EDGE_CURVE('',#18725,#18727,#7566,.T.); -#28000=EDGE_CURVE('',#18723,#18725,#7570,.T.); -#28002=EDGE_CURVE('',#18721,#18723,#7574,.T.); -#28004=EDGE_CURVE('',#18719,#18721,#7578,.T.); -#28006=EDGE_CURVE('',#18717,#18719,#7582,.T.); -#28008=EDGE_CURVE('',#18715,#18717,#7586,.T.); -#28010=EDGE_CURVE('',#18713,#18715,#7590,.T.); -#28012=EDGE_CURVE('',#18711,#18713,#7594,.T.); -#28014=EDGE_CURVE('',#18709,#18711,#7598,.T.); -#28016=EDGE_CURVE('',#18707,#18709,#7602,.T.); -#28018=EDGE_CURVE('',#18705,#18707,#7606,.T.); -#28020=EDGE_CURVE('',#18703,#18705,#7610,.T.); -#28022=EDGE_CURVE('',#18701,#18703,#7614,.T.); -#28024=EDGE_CURVE('',#18699,#18701,#7618,.T.); -#28026=EDGE_CURVE('',#18697,#18699,#7622,.T.); -#28028=EDGE_CURVE('',#18695,#18697,#7626,.T.); -#28030=EDGE_CURVE('',#18693,#18695,#7630,.T.); -#28032=EDGE_CURVE('',#18691,#18693,#7634,.T.); -#28034=EDGE_CURVE('',#18689,#18691,#7638,.T.); -#28036=EDGE_CURVE('',#18687,#18689,#7642,.T.); -#28038=EDGE_CURVE('',#18685,#18687,#7646,.T.); -#28040=EDGE_CURVE('',#18683,#18685,#7650,.T.); -#28042=EDGE_CURVE('',#18681,#18683,#7654,.T.); -#28044=EDGE_CURVE('',#18679,#18681,#7658,.T.); -#28046=EDGE_CURVE('',#18677,#18679,#7662,.T.); -#28048=EDGE_CURVE('',#18675,#18677,#7666,.T.); -#28050=EDGE_CURVE('',#18673,#18675,#7670,.T.); -#28052=EDGE_CURVE('',#18671,#18673,#7674,.T.); -#28054=EDGE_CURVE('',#18669,#18671,#7678,.T.); -#28056=EDGE_CURVE('',#18667,#18669,#7682,.T.); -#28058=EDGE_CURVE('',#18665,#18667,#7686,.T.); -#28060=EDGE_CURVE('',#18663,#18665,#7690,.T.); -#28064=ADVANCED_FACE('',(#28063),#27981,.T.); -#28077=EDGE_CURVE('',#18742,#18743,#7694,.T.); -#28079=EDGE_CURVE('',#18819,#18742,#7698,.T.); -#28081=EDGE_CURVE('',#18817,#18819,#7702,.T.); -#28083=EDGE_CURVE('',#18815,#18817,#7706,.T.); -#28085=EDGE_CURVE('',#18813,#18815,#7710,.T.); -#28087=EDGE_CURVE('',#18811,#18813,#7714,.T.); -#28089=EDGE_CURVE('',#18809,#18811,#7718,.T.); -#28091=EDGE_CURVE('',#18807,#18809,#7722,.T.); -#28093=EDGE_CURVE('',#18805,#18807,#7726,.T.); -#28095=EDGE_CURVE('',#18803,#18805,#7730,.T.); -#28097=EDGE_CURVE('',#18801,#18803,#7734,.T.); -#28099=EDGE_CURVE('',#18799,#18801,#7738,.T.); -#28101=EDGE_CURVE('',#18797,#18799,#7742,.T.); -#28103=EDGE_CURVE('',#18795,#18797,#7746,.T.); -#28105=EDGE_CURVE('',#18793,#18795,#7750,.T.); -#28107=EDGE_CURVE('',#18791,#18793,#7754,.T.); -#28109=EDGE_CURVE('',#18789,#18791,#7758,.T.); -#28111=EDGE_CURVE('',#18787,#18789,#7762,.T.); -#28113=EDGE_CURVE('',#18785,#18787,#7766,.T.); -#28115=EDGE_CURVE('',#18783,#18785,#7770,.T.); -#28117=EDGE_CURVE('',#18781,#18783,#7774,.T.); -#28119=EDGE_CURVE('',#18779,#18781,#7778,.T.); -#28121=EDGE_CURVE('',#18777,#18779,#7782,.T.); -#28123=EDGE_CURVE('',#18775,#18777,#7786,.T.); -#28125=EDGE_CURVE('',#18773,#18775,#7790,.T.); -#28127=EDGE_CURVE('',#18771,#18773,#7794,.T.); -#28129=EDGE_CURVE('',#18769,#18771,#7798,.T.); -#28131=EDGE_CURVE('',#18767,#18769,#7802,.T.); -#28133=EDGE_CURVE('',#18765,#18767,#7806,.T.); -#28135=EDGE_CURVE('',#18763,#18765,#7810,.T.); -#28137=EDGE_CURVE('',#18761,#18763,#7814,.T.); -#28139=EDGE_CURVE('',#18759,#18761,#7818,.T.); -#28141=EDGE_CURVE('',#18757,#18759,#7822,.T.); -#28143=EDGE_CURVE('',#18755,#18757,#7826,.T.); -#28145=EDGE_CURVE('',#18753,#18755,#7830,.T.); -#28147=EDGE_CURVE('',#18751,#18753,#7834,.T.); -#28149=EDGE_CURVE('',#18749,#18751,#7838,.T.); -#28151=EDGE_CURVE('',#18747,#18749,#7842,.T.); -#28153=EDGE_CURVE('',#18745,#18747,#7846,.T.); -#28155=EDGE_CURVE('',#18743,#18745,#7850,.T.); -#28159=ADVANCED_FACE('',(#28158),#28076,.T.); -#28172=EDGE_CURVE('',#18822,#18823,#7854,.T.); -#28174=EDGE_CURVE('',#18827,#18822,#7858,.T.); -#28176=EDGE_CURVE('',#18825,#18827,#7862,.T.); -#28178=EDGE_CURVE('',#18823,#18825,#7866,.T.); -#28182=ADVANCED_FACE('',(#28181),#28171,.T.); -#28195=EDGE_CURVE('',#18830,#18831,#7870,.T.); -#28197=EDGE_CURVE('',#18855,#18830,#7874,.T.); -#28199=EDGE_CURVE('',#18853,#18855,#7878,.T.); -#28201=EDGE_CURVE('',#18851,#18853,#7882,.T.); -#28203=EDGE_CURVE('',#18849,#18851,#7886,.T.); -#28205=EDGE_CURVE('',#18847,#18849,#7890,.T.); -#28207=EDGE_CURVE('',#18845,#18847,#7894,.T.); -#28209=EDGE_CURVE('',#18843,#18845,#7898,.T.); -#28211=EDGE_CURVE('',#18841,#18843,#7902,.T.); -#28213=EDGE_CURVE('',#18839,#18841,#7906,.T.); -#28215=EDGE_CURVE('',#18837,#18839,#7910,.T.); -#28217=EDGE_CURVE('',#18835,#18837,#7914,.T.); -#28219=EDGE_CURVE('',#18833,#18835,#7918,.T.); -#28221=EDGE_CURVE('',#18831,#18833,#7922,.T.); -#28225=EDGE_CURVE('',#18858,#18859,#7926,.T.); -#28227=EDGE_CURVE('',#18879,#18858,#7930,.T.); -#28229=EDGE_CURVE('',#18877,#18879,#7934,.T.); -#28231=EDGE_CURVE('',#18875,#18877,#7938,.T.); -#28233=EDGE_CURVE('',#18873,#18875,#7942,.T.); -#28235=EDGE_CURVE('',#18871,#18873,#7946,.T.); -#28237=EDGE_CURVE('',#18869,#18871,#7950,.T.); -#28239=EDGE_CURVE('',#18867,#18869,#7954,.T.); -#28241=EDGE_CURVE('',#18865,#18867,#7958,.T.); -#28243=EDGE_CURVE('',#18863,#18865,#7962,.T.); -#28245=EDGE_CURVE('',#18861,#18863,#7966,.T.); -#28247=EDGE_CURVE('',#18859,#18861,#7970,.T.); -#28251=ADVANCED_FACE('',(#28224,#28250),#28194,.T.); -#28264=EDGE_CURVE('',#18882,#18883,#7974,.T.); -#28266=EDGE_CURVE('',#18887,#18882,#7978,.T.); -#28268=EDGE_CURVE('',#18885,#18887,#7982,.T.); -#28270=EDGE_CURVE('',#18883,#18885,#7986,.T.); -#28274=ADVANCED_FACE('',(#28273),#28263,.T.); -#28287=EDGE_CURVE('',#18890,#18891,#7990,.T.); -#28289=EDGE_CURVE('',#18895,#18890,#7994,.T.); -#28291=EDGE_CURVE('',#18893,#18895,#7998,.T.); -#28293=EDGE_CURVE('',#18891,#18893,#8002,.T.); -#28297=ADVANCED_FACE('',(#28296),#28286,.T.); -#28310=EDGE_CURVE('',#18898,#18899,#8006,.T.); -#28312=EDGE_CURVE('',#18919,#18898,#8010,.T.); -#28314=EDGE_CURVE('',#18917,#18919,#8014,.T.); -#28316=EDGE_CURVE('',#18915,#18917,#8018,.T.); -#28318=EDGE_CURVE('',#18913,#18915,#8022,.T.); -#28320=EDGE_CURVE('',#18911,#18913,#8026,.T.); -#28322=EDGE_CURVE('',#18909,#18911,#8030,.T.); -#28324=EDGE_CURVE('',#18907,#18909,#8034,.T.); -#28326=EDGE_CURVE('',#18905,#18907,#8038,.T.); -#28328=EDGE_CURVE('',#18903,#18905,#8042,.T.); -#28330=EDGE_CURVE('',#18901,#18903,#8046,.T.); -#28332=EDGE_CURVE('',#18899,#18901,#8050,.T.); -#28336=ADVANCED_FACE('',(#28335),#28309,.T.); -#28349=EDGE_CURVE('',#18922,#18923,#8054,.T.); -#28351=EDGE_CURVE('',#18987,#18922,#8058,.T.); -#28353=EDGE_CURVE('',#18985,#18987,#8062,.T.); -#28355=EDGE_CURVE('',#18983,#18985,#8066,.T.); -#28357=EDGE_CURVE('',#18981,#18983,#8070,.T.); -#28359=EDGE_CURVE('',#18979,#18981,#8074,.T.); -#28361=EDGE_CURVE('',#18977,#18979,#8078,.T.); -#28363=EDGE_CURVE('',#18975,#18977,#8082,.T.); -#28365=EDGE_CURVE('',#18973,#18975,#8086,.T.); -#28367=EDGE_CURVE('',#18971,#18973,#8090,.T.); -#28369=EDGE_CURVE('',#18969,#18971,#8094,.T.); -#28371=EDGE_CURVE('',#18967,#18969,#8098,.T.); -#28373=EDGE_CURVE('',#18965,#18967,#8102,.T.); -#28375=EDGE_CURVE('',#18963,#18965,#8106,.T.); -#28377=EDGE_CURVE('',#18961,#18963,#8110,.T.); -#28379=EDGE_CURVE('',#18959,#18961,#8114,.T.); -#28381=EDGE_CURVE('',#18957,#18959,#8118,.T.); -#28383=EDGE_CURVE('',#18955,#18957,#8122,.T.); -#28385=EDGE_CURVE('',#18953,#18955,#8126,.T.); -#28387=EDGE_CURVE('',#18951,#18953,#8130,.T.); -#28389=EDGE_CURVE('',#18949,#18951,#8134,.T.); -#28391=EDGE_CURVE('',#18947,#18949,#8138,.T.); -#28393=EDGE_CURVE('',#18945,#18947,#8142,.T.); -#28395=EDGE_CURVE('',#18943,#18945,#8146,.T.); -#28397=EDGE_CURVE('',#18941,#18943,#8150,.T.); -#28399=EDGE_CURVE('',#18939,#18941,#8154,.T.); -#28401=EDGE_CURVE('',#18937,#18939,#8158,.T.); -#28403=EDGE_CURVE('',#18935,#18937,#8162,.T.); -#28405=EDGE_CURVE('',#18933,#18935,#8166,.T.); -#28407=EDGE_CURVE('',#18931,#18933,#8170,.T.); -#28409=EDGE_CURVE('',#18929,#18931,#8174,.T.); -#28411=EDGE_CURVE('',#18927,#18929,#8178,.T.); -#28413=EDGE_CURVE('',#18925,#18927,#8182,.T.); -#28415=EDGE_CURVE('',#18923,#18925,#8186,.T.); -#28419=EDGE_CURVE('',#18990,#18991,#8190,.T.); -#28421=EDGE_CURVE('',#19019,#18990,#8194,.T.); -#28423=EDGE_CURVE('',#19017,#19019,#8198,.T.); -#28425=EDGE_CURVE('',#19015,#19017,#8202,.T.); -#28427=EDGE_CURVE('',#19013,#19015,#8206,.T.); -#28429=EDGE_CURVE('',#19011,#19013,#8210,.T.); -#28431=EDGE_CURVE('',#19009,#19011,#8214,.T.); -#28433=EDGE_CURVE('',#19007,#19009,#8218,.T.); -#28435=EDGE_CURVE('',#19005,#19007,#8222,.T.); -#28437=EDGE_CURVE('',#19003,#19005,#8226,.T.); -#28439=EDGE_CURVE('',#19001,#19003,#8230,.T.); -#28441=EDGE_CURVE('',#18999,#19001,#8234,.T.); -#28443=EDGE_CURVE('',#18997,#18999,#8238,.T.); -#28445=EDGE_CURVE('',#18995,#18997,#8242,.T.); -#28447=EDGE_CURVE('',#18993,#18995,#8246,.T.); -#28449=EDGE_CURVE('',#18991,#18993,#8250,.T.); -#28453=EDGE_CURVE('',#19022,#19023,#8254,.T.); -#28455=EDGE_CURVE('',#19051,#19022,#8258,.T.); -#28457=EDGE_CURVE('',#19049,#19051,#8262,.T.); -#28459=EDGE_CURVE('',#19047,#19049,#8266,.T.); -#28461=EDGE_CURVE('',#19045,#19047,#8270,.T.); -#28463=EDGE_CURVE('',#19043,#19045,#8274,.T.); -#28465=EDGE_CURVE('',#19041,#19043,#8278,.T.); -#28467=EDGE_CURVE('',#19039,#19041,#8282,.T.); -#28469=EDGE_CURVE('',#19037,#19039,#8286,.T.); -#28471=EDGE_CURVE('',#19035,#19037,#8290,.T.); -#28473=EDGE_CURVE('',#19033,#19035,#8294,.T.); -#28475=EDGE_CURVE('',#19031,#19033,#8298,.T.); -#28477=EDGE_CURVE('',#19029,#19031,#8302,.T.); -#28479=EDGE_CURVE('',#19027,#19029,#8306,.T.); -#28481=EDGE_CURVE('',#19025,#19027,#8310,.T.); -#28483=EDGE_CURVE('',#19023,#19025,#8314,.T.); -#28487=ADVANCED_FACE('',(#28418,#28452,#28486),#28348,.T.); -#28500=EDGE_CURVE('',#19054,#19055,#8318,.T.); -#28502=EDGE_CURVE('',#19077,#19054,#8322,.T.); -#28504=EDGE_CURVE('',#19075,#19077,#8326,.T.); -#28506=EDGE_CURVE('',#19073,#19075,#8330,.T.); -#28508=EDGE_CURVE('',#19071,#19073,#8334,.T.); -#28510=EDGE_CURVE('',#19069,#19071,#8338,.T.); -#28512=EDGE_CURVE('',#19067,#19069,#8342,.T.); -#28514=EDGE_CURVE('',#19065,#19067,#8346,.T.); -#28516=EDGE_CURVE('',#19063,#19065,#8350,.T.); -#28518=EDGE_CURVE('',#19061,#19063,#8354,.T.); -#28520=EDGE_CURVE('',#19059,#19061,#8358,.T.); -#28522=EDGE_CURVE('',#19057,#19059,#8362,.T.); -#28524=EDGE_CURVE('',#19055,#19057,#8366,.T.); -#28528=ADVANCED_FACE('',(#28527),#28499,.T.); -#28541=EDGE_CURVE('',#19080,#19081,#8370,.T.); -#28543=EDGE_CURVE('',#19115,#19080,#8374,.T.); -#28545=EDGE_CURVE('',#19113,#19115,#8378,.T.); -#28547=EDGE_CURVE('',#19111,#19113,#8382,.T.); -#28549=EDGE_CURVE('',#19109,#19111,#8386,.T.); -#28551=EDGE_CURVE('',#19107,#19109,#8390,.T.); -#28553=EDGE_CURVE('',#19105,#19107,#8394,.T.); -#28555=EDGE_CURVE('',#19103,#19105,#8398,.T.); -#28557=EDGE_CURVE('',#19101,#19103,#8402,.T.); -#28559=EDGE_CURVE('',#19099,#19101,#8406,.T.); -#28561=EDGE_CURVE('',#19097,#19099,#8410,.T.); -#28563=EDGE_CURVE('',#19095,#19097,#8414,.T.); -#28565=EDGE_CURVE('',#19093,#19095,#8418,.T.); -#28567=EDGE_CURVE('',#19091,#19093,#8422,.T.); -#28569=EDGE_CURVE('',#19089,#19091,#8426,.T.); -#28571=EDGE_CURVE('',#19087,#19089,#8430,.T.); -#28573=EDGE_CURVE('',#19085,#19087,#8434,.T.); -#28575=EDGE_CURVE('',#19083,#19085,#8438,.T.); -#28577=EDGE_CURVE('',#19081,#19083,#8442,.T.); -#28581=EDGE_CURVE('',#19118,#19119,#8446,.T.); -#28583=EDGE_CURVE('',#19135,#19118,#8450,.T.); -#28585=EDGE_CURVE('',#19133,#19135,#8454,.T.); -#28587=EDGE_CURVE('',#19131,#19133,#8458,.T.); -#28589=EDGE_CURVE('',#19129,#19131,#8462,.T.); -#28591=EDGE_CURVE('',#19127,#19129,#8466,.T.); -#28593=EDGE_CURVE('',#19125,#19127,#8470,.T.); -#28595=EDGE_CURVE('',#19123,#19125,#8474,.T.); -#28597=EDGE_CURVE('',#19121,#19123,#8478,.T.); -#28599=EDGE_CURVE('',#19119,#19121,#8482,.T.); -#28603=EDGE_CURVE('',#19138,#19139,#8486,.T.); -#28605=EDGE_CURVE('',#19155,#19138,#8490,.T.); -#28607=EDGE_CURVE('',#19153,#19155,#8494,.T.); -#28609=EDGE_CURVE('',#19151,#19153,#8498,.T.); -#28611=EDGE_CURVE('',#19149,#19151,#8502,.T.); -#28613=EDGE_CURVE('',#19147,#19149,#8506,.T.); -#28615=EDGE_CURVE('',#19145,#19147,#8510,.T.); -#28617=EDGE_CURVE('',#19143,#19145,#8514,.T.); -#28619=EDGE_CURVE('',#19141,#19143,#8518,.T.); -#28621=EDGE_CURVE('',#19139,#19141,#8522,.T.); -#28625=ADVANCED_FACE('',(#28580,#28602,#28624),#28540,.T.); -#28638=EDGE_CURVE('',#19158,#19159,#8526,.T.); -#28640=EDGE_CURVE('',#19171,#19158,#8530,.T.); -#28642=EDGE_CURVE('',#19169,#19171,#8534,.T.); -#28644=EDGE_CURVE('',#19167,#19169,#8538,.T.); -#28646=EDGE_CURVE('',#19165,#19167,#8542,.T.); -#28648=EDGE_CURVE('',#19163,#19165,#8546,.T.); -#28650=EDGE_CURVE('',#19161,#19163,#8550,.T.); -#28652=EDGE_CURVE('',#19159,#19161,#8554,.T.); -#28656=ADVANCED_FACE('',(#28655),#28637,.T.); -#28669=EDGE_CURVE('',#19174,#19175,#8558,.T.); -#28671=EDGE_CURVE('',#19239,#19174,#8562,.T.); -#28673=EDGE_CURVE('',#19237,#19239,#8566,.T.); -#28675=EDGE_CURVE('',#19235,#19237,#8570,.T.); -#28677=EDGE_CURVE('',#19233,#19235,#8574,.T.); -#28679=EDGE_CURVE('',#19231,#19233,#8578,.T.); -#28681=EDGE_CURVE('',#19229,#19231,#8582,.T.); -#28683=EDGE_CURVE('',#19227,#19229,#8586,.T.); -#28685=EDGE_CURVE('',#19225,#19227,#8590,.T.); -#28687=EDGE_CURVE('',#19223,#19225,#8594,.T.); -#28689=EDGE_CURVE('',#19221,#19223,#8598,.T.); -#28691=EDGE_CURVE('',#19219,#19221,#8602,.T.); -#28693=EDGE_CURVE('',#19217,#19219,#8606,.T.); -#28695=EDGE_CURVE('',#19215,#19217,#8610,.T.); -#28697=EDGE_CURVE('',#19213,#19215,#8614,.T.); -#28699=EDGE_CURVE('',#19211,#19213,#8618,.T.); -#28701=EDGE_CURVE('',#19209,#19211,#8622,.T.); -#28703=EDGE_CURVE('',#19207,#19209,#8626,.T.); -#28705=EDGE_CURVE('',#19205,#19207,#8630,.T.); -#28707=EDGE_CURVE('',#19203,#19205,#8634,.T.); -#28709=EDGE_CURVE('',#19201,#19203,#8638,.T.); -#28711=EDGE_CURVE('',#19199,#19201,#8642,.T.); -#28713=EDGE_CURVE('',#19197,#19199,#8646,.T.); -#28715=EDGE_CURVE('',#19195,#19197,#8650,.T.); -#28717=EDGE_CURVE('',#19193,#19195,#8654,.T.); -#28719=EDGE_CURVE('',#19191,#19193,#8658,.T.); -#28721=EDGE_CURVE('',#19189,#19191,#8662,.T.); -#28723=EDGE_CURVE('',#19187,#19189,#8666,.T.); -#28725=EDGE_CURVE('',#19185,#19187,#8670,.T.); -#28727=EDGE_CURVE('',#19183,#19185,#8674,.T.); -#28729=EDGE_CURVE('',#19181,#19183,#8678,.T.); -#28731=EDGE_CURVE('',#19179,#19181,#8682,.T.); -#28733=EDGE_CURVE('',#19177,#19179,#8686,.T.); -#28735=EDGE_CURVE('',#19175,#19177,#8690,.T.); -#28739=EDGE_CURVE('',#19242,#19243,#8694,.T.); -#28741=EDGE_CURVE('',#19271,#19242,#8698,.T.); -#28743=EDGE_CURVE('',#19269,#19271,#8702,.T.); -#28745=EDGE_CURVE('',#19267,#19269,#8706,.T.); -#28747=EDGE_CURVE('',#19265,#19267,#8710,.T.); -#28749=EDGE_CURVE('',#19263,#19265,#8714,.T.); -#28751=EDGE_CURVE('',#19261,#19263,#8718,.T.); -#28753=EDGE_CURVE('',#19259,#19261,#8722,.T.); -#28755=EDGE_CURVE('',#19257,#19259,#8726,.T.); -#28757=EDGE_CURVE('',#19255,#19257,#8730,.T.); -#28759=EDGE_CURVE('',#19253,#19255,#8734,.T.); -#28761=EDGE_CURVE('',#19251,#19253,#8738,.T.); -#28763=EDGE_CURVE('',#19249,#19251,#8742,.T.); -#28765=EDGE_CURVE('',#19247,#19249,#8746,.T.); -#28767=EDGE_CURVE('',#19245,#19247,#8750,.T.); -#28769=EDGE_CURVE('',#19243,#19245,#8754,.T.); -#28773=EDGE_CURVE('',#19274,#19275,#8758,.T.); -#28775=EDGE_CURVE('',#19303,#19274,#8762,.T.); -#28777=EDGE_CURVE('',#19301,#19303,#8766,.T.); -#28779=EDGE_CURVE('',#19299,#19301,#8770,.T.); -#28781=EDGE_CURVE('',#19297,#19299,#8774,.T.); -#28783=EDGE_CURVE('',#19295,#19297,#8778,.T.); -#28785=EDGE_CURVE('',#19293,#19295,#8782,.T.); -#28787=EDGE_CURVE('',#19291,#19293,#8786,.T.); -#28789=EDGE_CURVE('',#19289,#19291,#8790,.T.); -#28791=EDGE_CURVE('',#19287,#19289,#8794,.T.); -#28793=EDGE_CURVE('',#19285,#19287,#8798,.T.); -#28795=EDGE_CURVE('',#19283,#19285,#8802,.T.); -#28797=EDGE_CURVE('',#19281,#19283,#8806,.T.); -#28799=EDGE_CURVE('',#19279,#19281,#8810,.T.); -#28801=EDGE_CURVE('',#19277,#19279,#8814,.T.); -#28803=EDGE_CURVE('',#19275,#19277,#8818,.T.); -#28807=ADVANCED_FACE('',(#28738,#28772,#28806),#28668,.T.); -#28820=EDGE_CURVE('',#19306,#19307,#8822,.T.); -#28822=EDGE_CURVE('',#19417,#19306,#8826,.T.); -#28824=EDGE_CURVE('',#19415,#19417,#8830,.T.); -#28826=EDGE_CURVE('',#19413,#19415,#8834,.T.); -#28828=EDGE_CURVE('',#19411,#19413,#8838,.T.); -#28830=EDGE_CURVE('',#19409,#19411,#8842,.T.); -#28832=EDGE_CURVE('',#19407,#19409,#8846,.T.); -#28834=EDGE_CURVE('',#19405,#19407,#8850,.T.); -#28836=EDGE_CURVE('',#19403,#19405,#8854,.T.); -#28838=EDGE_CURVE('',#19401,#19403,#8858,.T.); -#28840=EDGE_CURVE('',#19399,#19401,#8862,.T.); -#28842=EDGE_CURVE('',#19397,#19399,#8866,.T.); -#28844=EDGE_CURVE('',#19395,#19397,#8870,.T.); -#28846=EDGE_CURVE('',#19393,#19395,#8874,.T.); -#28848=EDGE_CURVE('',#19391,#19393,#8878,.T.); -#28850=EDGE_CURVE('',#19389,#19391,#8882,.T.); -#28852=EDGE_CURVE('',#19387,#19389,#8886,.T.); -#28854=EDGE_CURVE('',#19385,#19387,#8890,.T.); -#28856=EDGE_CURVE('',#19383,#19385,#8894,.T.); -#28858=EDGE_CURVE('',#19381,#19383,#8898,.T.); -#28860=EDGE_CURVE('',#19379,#19381,#8902,.T.); -#28862=EDGE_CURVE('',#19377,#19379,#8906,.T.); -#28864=EDGE_CURVE('',#19375,#19377,#8910,.T.); -#28866=EDGE_CURVE('',#19373,#19375,#8914,.T.); -#28868=EDGE_CURVE('',#19371,#19373,#8918,.T.); -#28870=EDGE_CURVE('',#19369,#19371,#8922,.T.); -#28872=EDGE_CURVE('',#19367,#19369,#8926,.T.); -#28874=EDGE_CURVE('',#19365,#19367,#8930,.T.); -#28876=EDGE_CURVE('',#19363,#19365,#8934,.T.); -#28878=EDGE_CURVE('',#19361,#19363,#8938,.T.); -#28880=EDGE_CURVE('',#19359,#19361,#8942,.T.); -#28882=EDGE_CURVE('',#19357,#19359,#8946,.T.); -#28884=EDGE_CURVE('',#19355,#19357,#8950,.T.); -#28886=EDGE_CURVE('',#19353,#19355,#8954,.T.); -#28888=EDGE_CURVE('',#19351,#19353,#8958,.T.); -#28890=EDGE_CURVE('',#19349,#19351,#8962,.T.); -#28892=EDGE_CURVE('',#19347,#19349,#8966,.T.); -#28894=EDGE_CURVE('',#19345,#19347,#8970,.T.); -#28896=EDGE_CURVE('',#19343,#19345,#8974,.T.); -#28898=EDGE_CURVE('',#19341,#19343,#8978,.T.); -#28900=EDGE_CURVE('',#19339,#19341,#8982,.T.); -#28902=EDGE_CURVE('',#19337,#19339,#8986,.T.); -#28904=EDGE_CURVE('',#19335,#19337,#8990,.T.); -#28906=EDGE_CURVE('',#19333,#19335,#8994,.T.); -#28908=EDGE_CURVE('',#19331,#19333,#8998,.T.); -#28910=EDGE_CURVE('',#19329,#19331,#9002,.T.); -#28912=EDGE_CURVE('',#19327,#19329,#9006,.T.); -#28914=EDGE_CURVE('',#19325,#19327,#9010,.T.); -#28916=EDGE_CURVE('',#19323,#19325,#9014,.T.); -#28918=EDGE_CURVE('',#19321,#19323,#9018,.T.); -#28920=EDGE_CURVE('',#19319,#19321,#9022,.T.); -#28922=EDGE_CURVE('',#19317,#19319,#9026,.T.); -#28924=EDGE_CURVE('',#19315,#19317,#9030,.T.); -#28926=EDGE_CURVE('',#19313,#19315,#9034,.T.); -#28928=EDGE_CURVE('',#19311,#19313,#9038,.T.); -#28930=EDGE_CURVE('',#19309,#19311,#9042,.T.); -#28932=EDGE_CURVE('',#19307,#19309,#9046,.T.); -#28936=ADVANCED_FACE('',(#28935),#28819,.T.); -#28949=EDGE_CURVE('',#19420,#19421,#9050,.T.); -#28951=EDGE_CURVE('',#19473,#19420,#9054,.T.); -#28953=EDGE_CURVE('',#19471,#19473,#9058,.T.); -#28955=EDGE_CURVE('',#19469,#19471,#9062,.T.); -#28957=EDGE_CURVE('',#19467,#19469,#9066,.T.); -#28959=EDGE_CURVE('',#19465,#19467,#9070,.T.); -#28961=EDGE_CURVE('',#19463,#19465,#9074,.T.); -#28963=EDGE_CURVE('',#19461,#19463,#9078,.T.); -#28965=EDGE_CURVE('',#19459,#19461,#9082,.T.); -#28967=EDGE_CURVE('',#19457,#19459,#9086,.T.); -#28969=EDGE_CURVE('',#19455,#19457,#9090,.T.); -#28971=EDGE_CURVE('',#19453,#19455,#9094,.T.); -#28973=EDGE_CURVE('',#19451,#19453,#9098,.T.); -#28975=EDGE_CURVE('',#19449,#19451,#9102,.T.); -#28977=EDGE_CURVE('',#19447,#19449,#9106,.T.); -#28979=EDGE_CURVE('',#19445,#19447,#9110,.T.); -#28981=EDGE_CURVE('',#19443,#19445,#9114,.T.); -#28983=EDGE_CURVE('',#19441,#19443,#9118,.T.); -#28985=EDGE_CURVE('',#19439,#19441,#9122,.T.); -#28987=EDGE_CURVE('',#19437,#19439,#9126,.T.); -#28989=EDGE_CURVE('',#19435,#19437,#9130,.T.); -#28991=EDGE_CURVE('',#19433,#19435,#9134,.T.); -#28993=EDGE_CURVE('',#19431,#19433,#9138,.T.); -#28995=EDGE_CURVE('',#19429,#19431,#9142,.T.); -#28997=EDGE_CURVE('',#19427,#19429,#9146,.T.); -#28999=EDGE_CURVE('',#19425,#19427,#9150,.T.); -#29001=EDGE_CURVE('',#19423,#19425,#9154,.T.); -#29003=EDGE_CURVE('',#19421,#19423,#9158,.T.); -#29007=ADVANCED_FACE('',(#29006),#28948,.T.); -#29020=EDGE_CURVE('',#19476,#19477,#9162,.T.); -#29022=EDGE_CURVE('',#19481,#19476,#9166,.T.); -#29024=EDGE_CURVE('',#19479,#19481,#9170,.T.); -#29026=EDGE_CURVE('',#19477,#19479,#9174,.T.); -#29030=ADVANCED_FACE('',(#29029),#29019,.T.); -#29043=EDGE_CURVE('',#19484,#19485,#9178,.T.); -#29045=EDGE_CURVE('',#19561,#19484,#9182,.T.); -#29047=EDGE_CURVE('',#19559,#19561,#9186,.T.); -#29049=EDGE_CURVE('',#19557,#19559,#9190,.T.); -#29051=EDGE_CURVE('',#19555,#19557,#9194,.T.); -#29053=EDGE_CURVE('',#19553,#19555,#9198,.T.); -#29055=EDGE_CURVE('',#19551,#19553,#9202,.T.); -#29057=EDGE_CURVE('',#19549,#19551,#9206,.T.); -#29059=EDGE_CURVE('',#19547,#19549,#9210,.T.); -#29061=EDGE_CURVE('',#19545,#19547,#9214,.T.); -#29063=EDGE_CURVE('',#19543,#19545,#9218,.T.); -#29065=EDGE_CURVE('',#19541,#19543,#9222,.T.); -#29067=EDGE_CURVE('',#19539,#19541,#9226,.T.); -#29069=EDGE_CURVE('',#19537,#19539,#9230,.T.); -#29071=EDGE_CURVE('',#19535,#19537,#9234,.T.); -#29073=EDGE_CURVE('',#19533,#19535,#9238,.T.); -#29075=EDGE_CURVE('',#19531,#19533,#9242,.T.); -#29077=EDGE_CURVE('',#19529,#19531,#9246,.T.); -#29079=EDGE_CURVE('',#19527,#19529,#9250,.T.); -#29081=EDGE_CURVE('',#19525,#19527,#9254,.T.); -#29083=EDGE_CURVE('',#19523,#19525,#9258,.T.); -#29085=EDGE_CURVE('',#19521,#19523,#9262,.T.); -#29087=EDGE_CURVE('',#19519,#19521,#9266,.T.); -#29089=EDGE_CURVE('',#19517,#19519,#9270,.T.); -#29091=EDGE_CURVE('',#19515,#19517,#9274,.T.); -#29093=EDGE_CURVE('',#19513,#19515,#9278,.T.); -#29095=EDGE_CURVE('',#19511,#19513,#9282,.T.); -#29097=EDGE_CURVE('',#19509,#19511,#9286,.T.); -#29099=EDGE_CURVE('',#19507,#19509,#9290,.T.); -#29101=EDGE_CURVE('',#19505,#19507,#9294,.T.); -#29103=EDGE_CURVE('',#19503,#19505,#9298,.T.); -#29105=EDGE_CURVE('',#19501,#19503,#9302,.T.); -#29107=EDGE_CURVE('',#19499,#19501,#9306,.T.); -#29109=EDGE_CURVE('',#19497,#19499,#9310,.T.); -#29111=EDGE_CURVE('',#19495,#19497,#9314,.T.); -#29113=EDGE_CURVE('',#19493,#19495,#9318,.T.); -#29115=EDGE_CURVE('',#19491,#19493,#9322,.T.); -#29117=EDGE_CURVE('',#19489,#19491,#9326,.T.); -#29119=EDGE_CURVE('',#19487,#19489,#9330,.T.); -#29121=EDGE_CURVE('',#19485,#19487,#9334,.T.); -#29125=ADVANCED_FACE('',(#29124),#29042,.T.); -#29138=EDGE_CURVE('',#19564,#19565,#9338,.T.); -#29140=EDGE_CURVE('',#19569,#19564,#9342,.T.); -#29142=EDGE_CURVE('',#19567,#19569,#9346,.T.); -#29144=EDGE_CURVE('',#19565,#19567,#9350,.T.); -#29148=ADVANCED_FACE('',(#29147),#29137,.T.); -#29161=EDGE_CURVE('',#19572,#19573,#9354,.T.); -#29163=EDGE_CURVE('',#19597,#19572,#9358,.T.); -#29165=EDGE_CURVE('',#19595,#19597,#9362,.T.); -#29167=EDGE_CURVE('',#19593,#19595,#9366,.T.); -#29169=EDGE_CURVE('',#19591,#19593,#9370,.T.); -#29171=EDGE_CURVE('',#19589,#19591,#9374,.T.); -#29173=EDGE_CURVE('',#19587,#19589,#9378,.T.); -#29175=EDGE_CURVE('',#19585,#19587,#9382,.T.); -#29177=EDGE_CURVE('',#19583,#19585,#9386,.T.); -#29179=EDGE_CURVE('',#19581,#19583,#9390,.T.); -#29181=EDGE_CURVE('',#19579,#19581,#9394,.T.); -#29183=EDGE_CURVE('',#19577,#19579,#9398,.T.); -#29185=EDGE_CURVE('',#19575,#19577,#9402,.T.); -#29187=EDGE_CURVE('',#19573,#19575,#9406,.T.); -#29191=EDGE_CURVE('',#19600,#19601,#9410,.T.); -#29193=EDGE_CURVE('',#19621,#19600,#9414,.T.); -#29195=EDGE_CURVE('',#19619,#19621,#9418,.T.); -#29197=EDGE_CURVE('',#19617,#19619,#9422,.T.); -#29199=EDGE_CURVE('',#19615,#19617,#9426,.T.); -#29201=EDGE_CURVE('',#19613,#19615,#9430,.T.); -#29203=EDGE_CURVE('',#19611,#19613,#9434,.T.); -#29205=EDGE_CURVE('',#19609,#19611,#9438,.T.); -#29207=EDGE_CURVE('',#19607,#19609,#9442,.T.); -#29209=EDGE_CURVE('',#19605,#19607,#9446,.T.); -#29211=EDGE_CURVE('',#19603,#19605,#9450,.T.); -#29213=EDGE_CURVE('',#19601,#19603,#9454,.T.); -#29217=ADVANCED_FACE('',(#29190,#29216),#29160,.T.); -#29230=EDGE_CURVE('',#19624,#19625,#9458,.T.); -#29232=EDGE_CURVE('',#19629,#19624,#9462,.T.); -#29234=EDGE_CURVE('',#19627,#19629,#9466,.T.); -#29236=EDGE_CURVE('',#19625,#19627,#9470,.T.); -#29240=ADVANCED_FACE('',(#29239),#29229,.T.); -#29253=EDGE_CURVE('',#19632,#19633,#9474,.T.); -#29255=EDGE_CURVE('',#19637,#19632,#9478,.T.); -#29257=EDGE_CURVE('',#19635,#19637,#9482,.T.); -#29259=EDGE_CURVE('',#19633,#19635,#9486,.T.); -#29263=ADVANCED_FACE('',(#29262),#29252,.T.); -#29276=EDGE_CURVE('',#19640,#19641,#9490,.T.); -#29278=EDGE_CURVE('',#19659,#19640,#9494,.T.); -#29280=EDGE_CURVE('',#19657,#19659,#9498,.T.); -#29282=EDGE_CURVE('',#19655,#19657,#9502,.T.); -#29284=EDGE_CURVE('',#19653,#19655,#9506,.T.); -#29286=EDGE_CURVE('',#19651,#19653,#9510,.T.); -#29288=EDGE_CURVE('',#19649,#19651,#9514,.T.); -#29290=EDGE_CURVE('',#19647,#19649,#9518,.T.); -#29292=EDGE_CURVE('',#19645,#19647,#9522,.T.); -#29294=EDGE_CURVE('',#19643,#19645,#9526,.T.); -#29296=EDGE_CURVE('',#19641,#19643,#9530,.T.); -#29300=EDGE_CURVE('',#19662,#19663,#9534,.T.); -#29302=EDGE_CURVE('',#19665,#19662,#9538,.T.); -#29304=EDGE_CURVE('',#19663,#19665,#9542,.T.); -#29308=ADVANCED_FACE('',(#29299,#29307),#29275,.T.); -#29321=EDGE_CURVE('',#19668,#19669,#9546,.T.); -#29323=EDGE_CURVE('',#19679,#19668,#9550,.T.); -#29325=EDGE_CURVE('',#19677,#19679,#9554,.T.); -#29327=EDGE_CURVE('',#19675,#19677,#9558,.T.); -#29329=EDGE_CURVE('',#19673,#19675,#9562,.T.); -#29331=EDGE_CURVE('',#19671,#19673,#9566,.T.); -#29333=EDGE_CURVE('',#19669,#19671,#9570,.T.); -#29337=ADVANCED_FACE('',(#29336),#29320,.T.); -#29350=EDGE_CURVE('',#19682,#19683,#9574,.T.); -#29352=EDGE_CURVE('',#19731,#19682,#9578,.T.); -#29354=EDGE_CURVE('',#19729,#19731,#9582,.T.); -#29356=EDGE_CURVE('',#19727,#19729,#9586,.T.); -#29358=EDGE_CURVE('',#19725,#19727,#9590,.T.); -#29360=EDGE_CURVE('',#19723,#19725,#9594,.T.); -#29362=EDGE_CURVE('',#19721,#19723,#9598,.T.); -#29364=EDGE_CURVE('',#19719,#19721,#9602,.T.); -#29366=EDGE_CURVE('',#19717,#19719,#9606,.T.); -#29368=EDGE_CURVE('',#19715,#19717,#9610,.T.); -#29370=EDGE_CURVE('',#19713,#19715,#9614,.T.); -#29372=EDGE_CURVE('',#19711,#19713,#9618,.T.); -#29374=EDGE_CURVE('',#19709,#19711,#9622,.T.); -#29376=EDGE_CURVE('',#19707,#19709,#9626,.T.); -#29378=EDGE_CURVE('',#19705,#19707,#9630,.T.); -#29380=EDGE_CURVE('',#19703,#19705,#9634,.T.); -#29382=EDGE_CURVE('',#19701,#19703,#9638,.T.); -#29384=EDGE_CURVE('',#19699,#19701,#9642,.T.); -#29386=EDGE_CURVE('',#19697,#19699,#9646,.T.); -#29388=EDGE_CURVE('',#19695,#19697,#9650,.T.); -#29390=EDGE_CURVE('',#19693,#19695,#9654,.T.); -#29392=EDGE_CURVE('',#19691,#19693,#9658,.T.); -#29394=EDGE_CURVE('',#19689,#19691,#9662,.T.); -#29396=EDGE_CURVE('',#19687,#19689,#9666,.T.); -#29398=EDGE_CURVE('',#19685,#19687,#9670,.T.); -#29400=EDGE_CURVE('',#19683,#19685,#9674,.T.); -#29404=EDGE_CURVE('',#19734,#19735,#9678,.T.); -#29406=EDGE_CURVE('',#19767,#19734,#9682,.T.); -#29408=EDGE_CURVE('',#19765,#19767,#9686,.T.); -#29410=EDGE_CURVE('',#19763,#19765,#9690,.T.); -#29412=EDGE_CURVE('',#19761,#19763,#9694,.T.); -#29414=EDGE_CURVE('',#19759,#19761,#9698,.T.); -#29416=EDGE_CURVE('',#19757,#19759,#9702,.T.); -#29418=EDGE_CURVE('',#19755,#19757,#9706,.T.); -#29420=EDGE_CURVE('',#19753,#19755,#9710,.T.); -#29422=EDGE_CURVE('',#19751,#19753,#9714,.T.); -#29424=EDGE_CURVE('',#19749,#19751,#9718,.T.); -#29426=EDGE_CURVE('',#19747,#19749,#9722,.T.); -#29428=EDGE_CURVE('',#19745,#19747,#9726,.T.); -#29430=EDGE_CURVE('',#19743,#19745,#9730,.T.); -#29432=EDGE_CURVE('',#19741,#19743,#9734,.T.); -#29434=EDGE_CURVE('',#19739,#19741,#9738,.T.); -#29436=EDGE_CURVE('',#19737,#19739,#9742,.T.); -#29438=EDGE_CURVE('',#19735,#19737,#9746,.T.); -#29442=ADVANCED_FACE('',(#29403,#29441),#29349,.T.); -#29455=EDGE_CURVE('',#19770,#19771,#9750,.T.); -#29457=EDGE_CURVE('',#19819,#19770,#9754,.T.); -#29459=EDGE_CURVE('',#19817,#19819,#9758,.T.); -#29461=EDGE_CURVE('',#19815,#19817,#9762,.T.); -#29463=EDGE_CURVE('',#19813,#19815,#9766,.T.); -#29465=EDGE_CURVE('',#19811,#19813,#9770,.T.); -#29467=EDGE_CURVE('',#19809,#19811,#9774,.T.); -#29469=EDGE_CURVE('',#19807,#19809,#9778,.T.); -#29471=EDGE_CURVE('',#19805,#19807,#9782,.T.); -#29473=EDGE_CURVE('',#19803,#19805,#9786,.T.); -#29475=EDGE_CURVE('',#19801,#19803,#9790,.T.); -#29477=EDGE_CURVE('',#19799,#19801,#9794,.T.); -#29479=EDGE_CURVE('',#19797,#19799,#9798,.T.); -#29481=EDGE_CURVE('',#19795,#19797,#9802,.T.); -#29483=EDGE_CURVE('',#19793,#19795,#9806,.T.); -#29485=EDGE_CURVE('',#19791,#19793,#9810,.T.); -#29487=EDGE_CURVE('',#19789,#19791,#9814,.T.); -#29489=EDGE_CURVE('',#19787,#19789,#9818,.T.); -#29491=EDGE_CURVE('',#19785,#19787,#9822,.T.); -#29493=EDGE_CURVE('',#19783,#19785,#9826,.T.); -#29495=EDGE_CURVE('',#19781,#19783,#9830,.T.); -#29497=EDGE_CURVE('',#19779,#19781,#9834,.T.); -#29499=EDGE_CURVE('',#19777,#19779,#9838,.T.); -#29501=EDGE_CURVE('',#19775,#19777,#9842,.T.); -#29503=EDGE_CURVE('',#19773,#19775,#9846,.T.); -#29505=EDGE_CURVE('',#19771,#19773,#9850,.T.); -#29509=EDGE_CURVE('',#19822,#19823,#9854,.T.); -#29511=EDGE_CURVE('',#19855,#19822,#9858,.T.); -#29513=EDGE_CURVE('',#19853,#19855,#9862,.T.); -#29515=EDGE_CURVE('',#19851,#19853,#9866,.T.); -#29517=EDGE_CURVE('',#19849,#19851,#9870,.T.); -#29519=EDGE_CURVE('',#19847,#19849,#9874,.T.); -#29521=EDGE_CURVE('',#19845,#19847,#9878,.T.); -#29523=EDGE_CURVE('',#19843,#19845,#9882,.T.); -#29525=EDGE_CURVE('',#19841,#19843,#9886,.T.); -#29527=EDGE_CURVE('',#19839,#19841,#9890,.T.); -#29529=EDGE_CURVE('',#19837,#19839,#9894,.T.); -#29531=EDGE_CURVE('',#19835,#19837,#9898,.T.); -#29533=EDGE_CURVE('',#19833,#19835,#9902,.T.); -#29535=EDGE_CURVE('',#19831,#19833,#9906,.T.); -#29537=EDGE_CURVE('',#19829,#19831,#9910,.T.); -#29539=EDGE_CURVE('',#19827,#19829,#9914,.T.); -#29541=EDGE_CURVE('',#19825,#19827,#9918,.T.); -#29543=EDGE_CURVE('',#19823,#19825,#9922,.T.); -#29547=ADVANCED_FACE('',(#29508,#29546),#29454,.T.); -#29560=EDGE_CURVE('',#19858,#19859,#9926,.T.); -#29562=EDGE_CURVE('',#19871,#19858,#9930,.T.); -#29564=EDGE_CURVE('',#19869,#19871,#9934,.T.); -#29566=EDGE_CURVE('',#19867,#19869,#9938,.T.); -#29568=EDGE_CURVE('',#19865,#19867,#9942,.T.); -#29570=EDGE_CURVE('',#19863,#19865,#9946,.T.); -#29572=EDGE_CURVE('',#19861,#19863,#9950,.T.); -#29574=EDGE_CURVE('',#19859,#19861,#9954,.T.); -#29578=EDGE_CURVE('',#19874,#19875,#9958,.T.); -#29580=EDGE_CURVE('',#19877,#19874,#9962,.T.); -#29582=EDGE_CURVE('',#19875,#19877,#9966,.T.); -#29586=ADVANCED_FACE('',(#29577,#29585),#29559,.T.); -#29599=EDGE_CURVE('',#19880,#19881,#9970,.T.); -#29601=EDGE_CURVE('',#19885,#19880,#9974,.T.); -#29603=EDGE_CURVE('',#19883,#19885,#9978,.T.); -#29605=EDGE_CURVE('',#19881,#19883,#9982,.T.); -#29609=ADVANCED_FACE('',(#29608),#29598,.T.); -#29622=EDGE_CURVE('',#19888,#19889,#9986,.T.); -#29624=EDGE_CURVE('',#19923,#19888,#9990,.T.); -#29626=EDGE_CURVE('',#19921,#19923,#9994,.T.); -#29628=EDGE_CURVE('',#19919,#19921,#9998,.T.); -#29630=EDGE_CURVE('',#19917,#19919,#10002,.T.); -#29632=EDGE_CURVE('',#19915,#19917,#10006,.T.); -#29634=EDGE_CURVE('',#19913,#19915,#10010,.T.); -#29636=EDGE_CURVE('',#19911,#19913,#10014,.T.); -#29638=EDGE_CURVE('',#19909,#19911,#10018,.T.); -#29640=EDGE_CURVE('',#19907,#19909,#10022,.T.); -#29642=EDGE_CURVE('',#19905,#19907,#10026,.T.); -#29644=EDGE_CURVE('',#19903,#19905,#10030,.T.); -#29646=EDGE_CURVE('',#19901,#19903,#10034,.T.); -#29648=EDGE_CURVE('',#19899,#19901,#10038,.T.); -#29650=EDGE_CURVE('',#19897,#19899,#10042,.T.); -#29652=EDGE_CURVE('',#19895,#19897,#10046,.T.); -#29654=EDGE_CURVE('',#19893,#19895,#10050,.T.); -#29656=EDGE_CURVE('',#19891,#19893,#10054,.T.); -#29658=EDGE_CURVE('',#19889,#19891,#10058,.T.); -#29662=EDGE_CURVE('',#19926,#19927,#10062,.T.); -#29664=EDGE_CURVE('',#19943,#19926,#10066,.T.); -#29666=EDGE_CURVE('',#19941,#19943,#10070,.T.); -#29668=EDGE_CURVE('',#19939,#19941,#10074,.T.); -#29670=EDGE_CURVE('',#19937,#19939,#10078,.T.); -#29672=EDGE_CURVE('',#19935,#19937,#10082,.T.); -#29674=EDGE_CURVE('',#19933,#19935,#10086,.T.); -#29676=EDGE_CURVE('',#19931,#19933,#10090,.T.); -#29678=EDGE_CURVE('',#19929,#19931,#10094,.T.); -#29680=EDGE_CURVE('',#19927,#19929,#10098,.T.); -#29684=EDGE_CURVE('',#19946,#19947,#10102,.T.); -#29686=EDGE_CURVE('',#19963,#19946,#10106,.T.); -#29688=EDGE_CURVE('',#19961,#19963,#10110,.T.); -#29690=EDGE_CURVE('',#19959,#19961,#10114,.T.); -#29692=EDGE_CURVE('',#19957,#19959,#10118,.T.); -#29694=EDGE_CURVE('',#19955,#19957,#10122,.T.); -#29696=EDGE_CURVE('',#19953,#19955,#10126,.T.); -#29698=EDGE_CURVE('',#19951,#19953,#10130,.T.); -#29700=EDGE_CURVE('',#19949,#19951,#10134,.T.); -#29702=EDGE_CURVE('',#19947,#19949,#10138,.T.); -#29706=ADVANCED_FACE('',(#29661,#29683,#29705),#29621,.T.); -#29719=EDGE_CURVE('',#19966,#19967,#10142,.T.); -#29721=EDGE_CURVE('',#19979,#19966,#10146,.T.); -#29723=EDGE_CURVE('',#19977,#19979,#10150,.T.); -#29725=EDGE_CURVE('',#19975,#19977,#10154,.T.); -#29727=EDGE_CURVE('',#19973,#19975,#10158,.T.); -#29729=EDGE_CURVE('',#19971,#19973,#10162,.T.); -#29731=EDGE_CURVE('',#19969,#19971,#10166,.T.); -#29733=EDGE_CURVE('',#19967,#19969,#10170,.T.); -#29737=ADVANCED_FACE('',(#29736),#29718,.T.); -#29750=EDGE_CURVE('',#19982,#19983,#10174,.T.); -#29752=EDGE_CURVE('',#20047,#19982,#10178,.T.); -#29754=EDGE_CURVE('',#20045,#20047,#10182,.T.); -#29756=EDGE_CURVE('',#20043,#20045,#10186,.T.); -#29758=EDGE_CURVE('',#20041,#20043,#10190,.T.); -#29760=EDGE_CURVE('',#20039,#20041,#10194,.T.); -#29762=EDGE_CURVE('',#20037,#20039,#10198,.T.); -#29764=EDGE_CURVE('',#20035,#20037,#10202,.T.); -#29766=EDGE_CURVE('',#20033,#20035,#10206,.T.); -#29768=EDGE_CURVE('',#20031,#20033,#10210,.T.); -#29770=EDGE_CURVE('',#20029,#20031,#10214,.T.); -#29772=EDGE_CURVE('',#20027,#20029,#10218,.T.); -#29774=EDGE_CURVE('',#20025,#20027,#10222,.T.); -#29776=EDGE_CURVE('',#20023,#20025,#10226,.T.); -#29778=EDGE_CURVE('',#20021,#20023,#10230,.T.); -#29780=EDGE_CURVE('',#20019,#20021,#10234,.T.); -#29782=EDGE_CURVE('',#20017,#20019,#10238,.T.); -#29784=EDGE_CURVE('',#20015,#20017,#10242,.T.); -#29786=EDGE_CURVE('',#20013,#20015,#10246,.T.); -#29788=EDGE_CURVE('',#20011,#20013,#10250,.T.); -#29790=EDGE_CURVE('',#20009,#20011,#10254,.T.); -#29792=EDGE_CURVE('',#20007,#20009,#10258,.T.); -#29794=EDGE_CURVE('',#20005,#20007,#10262,.T.); -#29796=EDGE_CURVE('',#20003,#20005,#10266,.T.); -#29798=EDGE_CURVE('',#20001,#20003,#10270,.T.); -#29800=EDGE_CURVE('',#19999,#20001,#10274,.T.); -#29802=EDGE_CURVE('',#19997,#19999,#10278,.T.); -#29804=EDGE_CURVE('',#19995,#19997,#10282,.T.); -#29806=EDGE_CURVE('',#19993,#19995,#10286,.T.); -#29808=EDGE_CURVE('',#19991,#19993,#10290,.T.); -#29810=EDGE_CURVE('',#19989,#19991,#10294,.T.); -#29812=EDGE_CURVE('',#19987,#19989,#10298,.T.); -#29814=EDGE_CURVE('',#19985,#19987,#10302,.T.); -#29816=EDGE_CURVE('',#19983,#19985,#10306,.T.); -#29820=EDGE_CURVE('',#20050,#20051,#10310,.T.); -#29822=EDGE_CURVE('',#20079,#20050,#10314,.T.); -#29824=EDGE_CURVE('',#20077,#20079,#10318,.T.); -#29826=EDGE_CURVE('',#20075,#20077,#10322,.T.); -#29828=EDGE_CURVE('',#20073,#20075,#10326,.T.); -#29830=EDGE_CURVE('',#20071,#20073,#10330,.T.); -#29832=EDGE_CURVE('',#20069,#20071,#10334,.T.); -#29834=EDGE_CURVE('',#20067,#20069,#10338,.T.); -#29836=EDGE_CURVE('',#20065,#20067,#10342,.T.); -#29838=EDGE_CURVE('',#20063,#20065,#10346,.T.); -#29840=EDGE_CURVE('',#20061,#20063,#10350,.T.); -#29842=EDGE_CURVE('',#20059,#20061,#10354,.T.); -#29844=EDGE_CURVE('',#20057,#20059,#10358,.T.); -#29846=EDGE_CURVE('',#20055,#20057,#10362,.T.); -#29848=EDGE_CURVE('',#20053,#20055,#10366,.T.); -#29850=EDGE_CURVE('',#20051,#20053,#10370,.T.); -#29854=EDGE_CURVE('',#20082,#20083,#10374,.T.); -#29856=EDGE_CURVE('',#20111,#20082,#10378,.T.); -#29858=EDGE_CURVE('',#20109,#20111,#10382,.T.); -#29860=EDGE_CURVE('',#20107,#20109,#10386,.T.); -#29862=EDGE_CURVE('',#20105,#20107,#10390,.T.); -#29864=EDGE_CURVE('',#20103,#20105,#10394,.T.); -#29866=EDGE_CURVE('',#20101,#20103,#10398,.T.); -#29868=EDGE_CURVE('',#20099,#20101,#10402,.T.); -#29870=EDGE_CURVE('',#20097,#20099,#10406,.T.); -#29872=EDGE_CURVE('',#20095,#20097,#10410,.T.); -#29874=EDGE_CURVE('',#20093,#20095,#10414,.T.); -#29876=EDGE_CURVE('',#20091,#20093,#10418,.T.); -#29878=EDGE_CURVE('',#20089,#20091,#10422,.T.); -#29880=EDGE_CURVE('',#20087,#20089,#10426,.T.); -#29882=EDGE_CURVE('',#20085,#20087,#10430,.T.); -#29884=EDGE_CURVE('',#20083,#20085,#10434,.T.); -#29888=ADVANCED_FACE('',(#29819,#29853,#29887),#29749,.T.); -#29901=EDGE_CURVE('',#20114,#20115,#10438,.T.); -#29903=EDGE_CURVE('',#20225,#20114,#10442,.T.); -#29905=EDGE_CURVE('',#20223,#20225,#10446,.T.); -#29907=EDGE_CURVE('',#20221,#20223,#10450,.T.); -#29909=EDGE_CURVE('',#20219,#20221,#10454,.T.); -#29911=EDGE_CURVE('',#20217,#20219,#10458,.T.); -#29913=EDGE_CURVE('',#20215,#20217,#10462,.T.); -#29915=EDGE_CURVE('',#20213,#20215,#10466,.T.); -#29917=EDGE_CURVE('',#20211,#20213,#10470,.T.); -#29919=EDGE_CURVE('',#20209,#20211,#10474,.T.); -#29921=EDGE_CURVE('',#20207,#20209,#10478,.T.); -#29923=EDGE_CURVE('',#20205,#20207,#10482,.T.); -#29925=EDGE_CURVE('',#20203,#20205,#10486,.T.); -#29927=EDGE_CURVE('',#20201,#20203,#10490,.T.); -#29929=EDGE_CURVE('',#20199,#20201,#10494,.T.); -#29931=EDGE_CURVE('',#20197,#20199,#10498,.T.); -#29933=EDGE_CURVE('',#20195,#20197,#10502,.T.); -#29935=EDGE_CURVE('',#20193,#20195,#10506,.T.); -#29937=EDGE_CURVE('',#20191,#20193,#10510,.T.); -#29939=EDGE_CURVE('',#20189,#20191,#10514,.T.); -#29941=EDGE_CURVE('',#20187,#20189,#10518,.T.); -#29943=EDGE_CURVE('',#20185,#20187,#10522,.T.); -#29945=EDGE_CURVE('',#20183,#20185,#10526,.T.); -#29947=EDGE_CURVE('',#20181,#20183,#10530,.T.); -#29949=EDGE_CURVE('',#20179,#20181,#10534,.T.); -#29951=EDGE_CURVE('',#20177,#20179,#10538,.T.); -#29953=EDGE_CURVE('',#20175,#20177,#10542,.T.); -#29955=EDGE_CURVE('',#20173,#20175,#10546,.T.); -#29957=EDGE_CURVE('',#20171,#20173,#10550,.T.); -#29959=EDGE_CURVE('',#20169,#20171,#10554,.T.); -#29961=EDGE_CURVE('',#20167,#20169,#10558,.T.); -#29963=EDGE_CURVE('',#20165,#20167,#10562,.T.); -#29965=EDGE_CURVE('',#20163,#20165,#10566,.T.); -#29967=EDGE_CURVE('',#20161,#20163,#10570,.T.); -#29969=EDGE_CURVE('',#20159,#20161,#10574,.T.); -#29971=EDGE_CURVE('',#20157,#20159,#10578,.T.); -#29973=EDGE_CURVE('',#20155,#20157,#10582,.T.); -#29975=EDGE_CURVE('',#20153,#20155,#10586,.T.); -#29977=EDGE_CURVE('',#20151,#20153,#10590,.T.); -#29979=EDGE_CURVE('',#20149,#20151,#10594,.T.); -#29981=EDGE_CURVE('',#20147,#20149,#10598,.T.); -#29983=EDGE_CURVE('',#20145,#20147,#10602,.T.); -#29985=EDGE_CURVE('',#20143,#20145,#10606,.T.); -#29987=EDGE_CURVE('',#20141,#20143,#10610,.T.); -#29989=EDGE_CURVE('',#20139,#20141,#10614,.T.); -#29991=EDGE_CURVE('',#20137,#20139,#10618,.T.); -#29993=EDGE_CURVE('',#20135,#20137,#10622,.T.); -#29995=EDGE_CURVE('',#20133,#20135,#10626,.T.); -#29997=EDGE_CURVE('',#20131,#20133,#10630,.T.); -#29999=EDGE_CURVE('',#20129,#20131,#10634,.T.); -#30001=EDGE_CURVE('',#20127,#20129,#10638,.T.); -#30003=EDGE_CURVE('',#20125,#20127,#10642,.T.); -#30005=EDGE_CURVE('',#20123,#20125,#10646,.T.); -#30007=EDGE_CURVE('',#20121,#20123,#10650,.T.); -#30009=EDGE_CURVE('',#20119,#20121,#10654,.T.); -#30011=EDGE_CURVE('',#20117,#20119,#10658,.T.); -#30013=EDGE_CURVE('',#20115,#20117,#10662,.T.); -#30017=ADVANCED_FACE('',(#30016),#29900,.T.); -#30030=EDGE_CURVE('',#20228,#20229,#10666,.T.); -#30032=EDGE_CURVE('',#20281,#20228,#10670,.T.); -#30034=EDGE_CURVE('',#20279,#20281,#10674,.T.); -#30036=EDGE_CURVE('',#20277,#20279,#10678,.T.); -#30038=EDGE_CURVE('',#20275,#20277,#10682,.T.); -#30040=EDGE_CURVE('',#20273,#20275,#10686,.T.); -#30042=EDGE_CURVE('',#20271,#20273,#10690,.T.); -#30044=EDGE_CURVE('',#20269,#20271,#10694,.T.); -#30046=EDGE_CURVE('',#20267,#20269,#10698,.T.); -#30048=EDGE_CURVE('',#20265,#20267,#10702,.T.); -#30050=EDGE_CURVE('',#20263,#20265,#10706,.T.); -#30052=EDGE_CURVE('',#20261,#20263,#10710,.T.); -#30054=EDGE_CURVE('',#20259,#20261,#10714,.T.); -#30056=EDGE_CURVE('',#20257,#20259,#10718,.T.); -#30058=EDGE_CURVE('',#20255,#20257,#10722,.T.); -#30060=EDGE_CURVE('',#20253,#20255,#10726,.T.); -#30062=EDGE_CURVE('',#20251,#20253,#10730,.T.); -#30064=EDGE_CURVE('',#20249,#20251,#10734,.T.); -#30066=EDGE_CURVE('',#20247,#20249,#10738,.T.); -#30068=EDGE_CURVE('',#20245,#20247,#10742,.T.); -#30070=EDGE_CURVE('',#20243,#20245,#10746,.T.); -#30072=EDGE_CURVE('',#20241,#20243,#10750,.T.); -#30074=EDGE_CURVE('',#20239,#20241,#10754,.T.); -#30076=EDGE_CURVE('',#20237,#20239,#10758,.T.); -#30078=EDGE_CURVE('',#20235,#20237,#10762,.T.); -#30080=EDGE_CURVE('',#20233,#20235,#10766,.T.); -#30082=EDGE_CURVE('',#20231,#20233,#10770,.T.); -#30084=EDGE_CURVE('',#20229,#20231,#10774,.T.); -#30088=ADVANCED_FACE('',(#30087),#30029,.T.); -#30102=EDGE_CURVE('',#18004,#17584,#10778,.T.); -#30105=EDGE_CURVE('',#18005,#17585,#10814,.T.); -#30109=ADVANCED_FACE('',(#30108),#30100,.F.); -#30116=EDGE_CURVE('',#18021,#17601,#10782,.T.); -#30122=ADVANCED_FACE('',(#30121),#30114,.F.); -#30129=EDGE_CURVE('',#18019,#17599,#10786,.T.); -#30135=ADVANCED_FACE('',(#30134),#30127,.F.); -#30142=EDGE_CURVE('',#18017,#17597,#10790,.T.); -#30148=ADVANCED_FACE('',(#30147),#30140,.F.); -#30155=EDGE_CURVE('',#18015,#17595,#10794,.T.); -#30161=ADVANCED_FACE('',(#30160),#30153,.F.); -#30168=EDGE_CURVE('',#18013,#17593,#10798,.T.); -#30174=ADVANCED_FACE('',(#30173),#30166,.F.); -#30181=EDGE_CURVE('',#18011,#17591,#10802,.T.); -#30187=ADVANCED_FACE('',(#30186),#30179,.F.); -#30194=EDGE_CURVE('',#18009,#17589,#10806,.T.); -#30200=ADVANCED_FACE('',(#30199),#30192,.F.); -#30207=EDGE_CURVE('',#18007,#17587,#10810,.T.); -#30213=ADVANCED_FACE('',(#30212),#30205,.F.); -#30225=ADVANCED_FACE('',(#30224),#30218,.F.); -#30232=EDGE_CURVE('',#18024,#17604,#10818,.T.); -#30235=EDGE_CURVE('',#18025,#17605,#10854,.T.); -#30239=ADVANCED_FACE('',(#30238),#30230,.F.); -#30246=EDGE_CURVE('',#18041,#17621,#10822,.T.); -#30252=ADVANCED_FACE('',(#30251),#30244,.F.); -#30259=EDGE_CURVE('',#18039,#17619,#10826,.T.); -#30265=ADVANCED_FACE('',(#30264),#30257,.F.); -#30272=EDGE_CURVE('',#18037,#17617,#10830,.T.); -#30278=ADVANCED_FACE('',(#30277),#30270,.F.); -#30285=EDGE_CURVE('',#18035,#17615,#10834,.T.); -#30291=ADVANCED_FACE('',(#30290),#30283,.F.); -#30298=EDGE_CURVE('',#18033,#17613,#10838,.T.); -#30304=ADVANCED_FACE('',(#30303),#30296,.F.); -#30311=EDGE_CURVE('',#18031,#17611,#10842,.T.); -#30317=ADVANCED_FACE('',(#30316),#30309,.F.); -#30324=EDGE_CURVE('',#18029,#17609,#10846,.T.); -#30330=ADVANCED_FACE('',(#30329),#30322,.F.); -#30337=EDGE_CURVE('',#18027,#17607,#10850,.T.); -#30343=ADVANCED_FACE('',(#30342),#30335,.F.); -#30355=ADVANCED_FACE('',(#30354),#30348,.F.); -#30362=EDGE_CURVE('',#18044,#17624,#10858,.T.); -#30365=EDGE_CURVE('',#18045,#17625,#10886,.T.); -#30369=ADVANCED_FACE('',(#30368),#30360,.F.); -#30376=EDGE_CURVE('',#18057,#17637,#10862,.T.); -#30382=ADVANCED_FACE('',(#30381),#30374,.F.); -#30389=EDGE_CURVE('',#18055,#17635,#10866,.T.); -#30395=ADVANCED_FACE('',(#30394),#30387,.F.); -#30402=EDGE_CURVE('',#18053,#17633,#10870,.T.); -#30408=ADVANCED_FACE('',(#30407),#30400,.F.); -#30415=EDGE_CURVE('',#18051,#17631,#10874,.T.); -#30421=ADVANCED_FACE('',(#30420),#30413,.F.); -#30428=EDGE_CURVE('',#18049,#17629,#10878,.T.); -#30434=ADVANCED_FACE('',(#30433),#30426,.F.); -#30441=EDGE_CURVE('',#18047,#17627,#10882,.T.); -#30447=ADVANCED_FACE('',(#30446),#30439,.F.); -#30459=ADVANCED_FACE('',(#30458),#30452,.F.); -#30466=EDGE_CURVE('',#18060,#17640,#10890,.T.); -#30469=EDGE_CURVE('',#18061,#17641,#11022,.T.); -#30473=ADVANCED_FACE('',(#30472),#30464,.F.); -#30480=EDGE_CURVE('',#18125,#17705,#10894,.T.); -#30486=ADVANCED_FACE('',(#30485),#30478,.F.); -#30493=EDGE_CURVE('',#18123,#17703,#10898,.T.); -#30499=ADVANCED_FACE('',(#30498),#30491,.F.); -#30506=EDGE_CURVE('',#18121,#17701,#10902,.T.); -#30512=ADVANCED_FACE('',(#30511),#30504,.F.); -#30519=EDGE_CURVE('',#18119,#17699,#10906,.T.); -#30525=ADVANCED_FACE('',(#30524),#30517,.F.); -#30532=EDGE_CURVE('',#18117,#17697,#10910,.T.); -#30538=ADVANCED_FACE('',(#30537),#30530,.F.); -#30545=EDGE_CURVE('',#18115,#17695,#10914,.T.); -#30551=ADVANCED_FACE('',(#30550),#30543,.F.); -#30558=EDGE_CURVE('',#18113,#17693,#10918,.T.); -#30564=ADVANCED_FACE('',(#30563),#30556,.F.); -#30571=EDGE_CURVE('',#18111,#17691,#10922,.T.); -#30577=ADVANCED_FACE('',(#30576),#30569,.F.); -#30584=EDGE_CURVE('',#18109,#17689,#10926,.T.); -#30590=ADVANCED_FACE('',(#30589),#30582,.F.); -#30597=EDGE_CURVE('',#18107,#17687,#10930,.T.); -#30603=ADVANCED_FACE('',(#30602),#30595,.F.); -#30610=EDGE_CURVE('',#18105,#17685,#10934,.T.); -#30616=ADVANCED_FACE('',(#30615),#30608,.F.); -#30623=EDGE_CURVE('',#18103,#17683,#10938,.T.); -#30629=ADVANCED_FACE('',(#30628),#30621,.F.); -#30636=EDGE_CURVE('',#18101,#17681,#10942,.T.); -#30642=ADVANCED_FACE('',(#30641),#30634,.F.); -#30649=EDGE_CURVE('',#18099,#17679,#10946,.T.); -#30655=ADVANCED_FACE('',(#30654),#30647,.F.); -#30662=EDGE_CURVE('',#18097,#17677,#10950,.T.); -#30668=ADVANCED_FACE('',(#30667),#30660,.F.); -#30675=EDGE_CURVE('',#18095,#17675,#10954,.T.); -#30681=ADVANCED_FACE('',(#30680),#30673,.F.); -#30688=EDGE_CURVE('',#18093,#17673,#10958,.T.); -#30694=ADVANCED_FACE('',(#30693),#30686,.F.); -#30701=EDGE_CURVE('',#18091,#17671,#10962,.T.); -#30707=ADVANCED_FACE('',(#30706),#30699,.F.); -#30714=EDGE_CURVE('',#18089,#17669,#10966,.T.); -#30720=ADVANCED_FACE('',(#30719),#30712,.F.); -#30727=EDGE_CURVE('',#18087,#17667,#10970,.T.); -#30733=ADVANCED_FACE('',(#30732),#30725,.F.); -#30740=EDGE_CURVE('',#18085,#17665,#10974,.T.); -#30746=ADVANCED_FACE('',(#30745),#30738,.F.); -#30753=EDGE_CURVE('',#18083,#17663,#10978,.T.); -#30759=ADVANCED_FACE('',(#30758),#30751,.F.); -#30766=EDGE_CURVE('',#18081,#17661,#10982,.T.); -#30772=ADVANCED_FACE('',(#30771),#30764,.F.); -#30779=EDGE_CURVE('',#18079,#17659,#10986,.T.); -#30785=ADVANCED_FACE('',(#30784),#30777,.F.); -#30792=EDGE_CURVE('',#18077,#17657,#10990,.T.); -#30798=ADVANCED_FACE('',(#30797),#30790,.F.); -#30805=EDGE_CURVE('',#18075,#17655,#10994,.T.); -#30811=ADVANCED_FACE('',(#30810),#30803,.F.); -#30818=EDGE_CURVE('',#18073,#17653,#10998,.T.); -#30824=ADVANCED_FACE('',(#30823),#30816,.F.); -#30831=EDGE_CURVE('',#18071,#17651,#11002,.T.); -#30837=ADVANCED_FACE('',(#30836),#30829,.F.); -#30844=EDGE_CURVE('',#18069,#17649,#11006,.T.); -#30850=ADVANCED_FACE('',(#30849),#30842,.F.); -#30857=EDGE_CURVE('',#18067,#17647,#11010,.T.); -#30863=ADVANCED_FACE('',(#30862),#30855,.F.); -#30870=EDGE_CURVE('',#18065,#17645,#11014,.T.); -#30876=ADVANCED_FACE('',(#30875),#30868,.F.); -#30883=EDGE_CURVE('',#18063,#17643,#11018,.T.); -#30889=ADVANCED_FACE('',(#30888),#30881,.F.); -#30901=ADVANCED_FACE('',(#30900),#30894,.F.); -#30908=EDGE_CURVE('',#18128,#17708,#11026,.T.); -#30911=EDGE_CURVE('',#18129,#17709,#11086,.T.); -#30915=ADVANCED_FACE('',(#30914),#30906,.F.); -#30922=EDGE_CURVE('',#18157,#17737,#11030,.T.); -#30928=ADVANCED_FACE('',(#30927),#30920,.F.); -#30935=EDGE_CURVE('',#18155,#17735,#11034,.T.); -#30941=ADVANCED_FACE('',(#30940),#30933,.F.); -#30948=EDGE_CURVE('',#18153,#17733,#11038,.T.); -#30954=ADVANCED_FACE('',(#30953),#30946,.F.); -#30961=EDGE_CURVE('',#18151,#17731,#11042,.T.); -#30967=ADVANCED_FACE('',(#30966),#30959,.F.); -#30974=EDGE_CURVE('',#18149,#17729,#11046,.T.); -#30980=ADVANCED_FACE('',(#30979),#30972,.F.); -#30987=EDGE_CURVE('',#18147,#17727,#11050,.T.); -#30993=ADVANCED_FACE('',(#30992),#30985,.F.); -#31000=EDGE_CURVE('',#18145,#17725,#11054,.T.); -#31006=ADVANCED_FACE('',(#31005),#30998,.F.); -#31013=EDGE_CURVE('',#18143,#17723,#11058,.T.); -#31019=ADVANCED_FACE('',(#31018),#31011,.F.); -#31026=EDGE_CURVE('',#18141,#17721,#11062,.T.); -#31032=ADVANCED_FACE('',(#31031),#31024,.F.); -#31039=EDGE_CURVE('',#18139,#17719,#11066,.T.); -#31045=ADVANCED_FACE('',(#31044),#31037,.F.); -#31052=EDGE_CURVE('',#18137,#17717,#11070,.T.); -#31058=ADVANCED_FACE('',(#31057),#31050,.F.); -#31065=EDGE_CURVE('',#18135,#17715,#11074,.T.); -#31071=ADVANCED_FACE('',(#31070),#31063,.F.); -#31078=EDGE_CURVE('',#18133,#17713,#11078,.T.); -#31084=ADVANCED_FACE('',(#31083),#31076,.F.); -#31091=EDGE_CURVE('',#18131,#17711,#11082,.T.); -#31097=ADVANCED_FACE('',(#31096),#31089,.F.); -#31109=ADVANCED_FACE('',(#31108),#31102,.F.); -#31116=EDGE_CURVE('',#18160,#17740,#11090,.T.); -#31119=EDGE_CURVE('',#18161,#17741,#11150,.T.); -#31123=ADVANCED_FACE('',(#31122),#31114,.F.); -#31130=EDGE_CURVE('',#18189,#17769,#11094,.T.); -#31136=ADVANCED_FACE('',(#31135),#31128,.F.); -#31143=EDGE_CURVE('',#18187,#17767,#11098,.T.); -#31149=ADVANCED_FACE('',(#31148),#31141,.F.); -#31156=EDGE_CURVE('',#18185,#17765,#11102,.T.); -#31162=ADVANCED_FACE('',(#31161),#31154,.F.); -#31169=EDGE_CURVE('',#18183,#17763,#11106,.T.); -#31175=ADVANCED_FACE('',(#31174),#31167,.F.); -#31182=EDGE_CURVE('',#18181,#17761,#11110,.T.); -#31188=ADVANCED_FACE('',(#31187),#31180,.F.); -#31195=EDGE_CURVE('',#18179,#17759,#11114,.T.); -#31201=ADVANCED_FACE('',(#31200),#31193,.F.); -#31208=EDGE_CURVE('',#18177,#17757,#11118,.T.); -#31214=ADVANCED_FACE('',(#31213),#31206,.F.); -#31221=EDGE_CURVE('',#18175,#17755,#11122,.T.); -#31227=ADVANCED_FACE('',(#31226),#31219,.F.); -#31234=EDGE_CURVE('',#18173,#17753,#11126,.T.); -#31240=ADVANCED_FACE('',(#31239),#31232,.F.); -#31247=EDGE_CURVE('',#18171,#17751,#11130,.T.); -#31253=ADVANCED_FACE('',(#31252),#31245,.F.); -#31260=EDGE_CURVE('',#18169,#17749,#11134,.T.); -#31266=ADVANCED_FACE('',(#31265),#31258,.F.); -#31273=EDGE_CURVE('',#18167,#17747,#11138,.T.); -#31279=ADVANCED_FACE('',(#31278),#31271,.F.); -#31286=EDGE_CURVE('',#18165,#17745,#11142,.T.); -#31292=ADVANCED_FACE('',(#31291),#31284,.F.); -#31299=EDGE_CURVE('',#18163,#17743,#11146,.T.); -#31305=ADVANCED_FACE('',(#31304),#31297,.F.); -#31317=ADVANCED_FACE('',(#31316),#31310,.F.); -#31324=EDGE_CURVE('',#18192,#17772,#11154,.T.); -#31327=EDGE_CURVE('',#18193,#17773,#11378,.T.); -#31331=ADVANCED_FACE('',(#31330),#31322,.F.); -#31338=EDGE_CURVE('',#18303,#17883,#11158,.T.); -#31344=ADVANCED_FACE('',(#31343),#31336,.F.); -#31351=EDGE_CURVE('',#18301,#17881,#11162,.T.); -#31357=ADVANCED_FACE('',(#31356),#31349,.F.); -#31364=EDGE_CURVE('',#18299,#17879,#11166,.T.); -#31370=ADVANCED_FACE('',(#31369),#31362,.F.); -#31377=EDGE_CURVE('',#18297,#17877,#11170,.T.); -#31383=ADVANCED_FACE('',(#31382),#31375,.F.); -#31390=EDGE_CURVE('',#18295,#17875,#11174,.T.); -#31396=ADVANCED_FACE('',(#31395),#31388,.F.); -#31403=EDGE_CURVE('',#18293,#17873,#11178,.T.); -#31409=ADVANCED_FACE('',(#31408),#31401,.F.); -#31416=EDGE_CURVE('',#18291,#17871,#11182,.T.); -#31422=ADVANCED_FACE('',(#31421),#31414,.F.); -#31429=EDGE_CURVE('',#18289,#17869,#11186,.T.); -#31435=ADVANCED_FACE('',(#31434),#31427,.F.); -#31442=EDGE_CURVE('',#18287,#17867,#11190,.T.); -#31448=ADVANCED_FACE('',(#31447),#31440,.F.); -#31455=EDGE_CURVE('',#18285,#17865,#11194,.T.); -#31461=ADVANCED_FACE('',(#31460),#31453,.F.); -#31468=EDGE_CURVE('',#18283,#17863,#11198,.T.); -#31474=ADVANCED_FACE('',(#31473),#31466,.F.); -#31481=EDGE_CURVE('',#18281,#17861,#11202,.T.); -#31487=ADVANCED_FACE('',(#31486),#31479,.F.); -#31494=EDGE_CURVE('',#18279,#17859,#11206,.T.); -#31500=ADVANCED_FACE('',(#31499),#31492,.F.); -#31507=EDGE_CURVE('',#18277,#17857,#11210,.T.); -#31513=ADVANCED_FACE('',(#31512),#31505,.F.); -#31520=EDGE_CURVE('',#18275,#17855,#11214,.T.); -#31526=ADVANCED_FACE('',(#31525),#31518,.F.); -#31533=EDGE_CURVE('',#18273,#17853,#11218,.T.); -#31539=ADVANCED_FACE('',(#31538),#31531,.F.); -#31546=EDGE_CURVE('',#18271,#17851,#11222,.T.); -#31552=ADVANCED_FACE('',(#31551),#31544,.F.); -#31559=EDGE_CURVE('',#18269,#17849,#11226,.T.); -#31565=ADVANCED_FACE('',(#31564),#31557,.F.); -#31572=EDGE_CURVE('',#18267,#17847,#11230,.T.); -#31578=ADVANCED_FACE('',(#31577),#31570,.F.); -#31585=EDGE_CURVE('',#18265,#17845,#11234,.T.); -#31591=ADVANCED_FACE('',(#31590),#31583,.F.); -#31598=EDGE_CURVE('',#18263,#17843,#11238,.T.); -#31604=ADVANCED_FACE('',(#31603),#31596,.F.); -#31611=EDGE_CURVE('',#18261,#17841,#11242,.T.); -#31617=ADVANCED_FACE('',(#31616),#31609,.F.); -#31624=EDGE_CURVE('',#18259,#17839,#11246,.T.); -#31630=ADVANCED_FACE('',(#31629),#31622,.F.); -#31637=EDGE_CURVE('',#18257,#17837,#11250,.T.); -#31643=ADVANCED_FACE('',(#31642),#31635,.F.); -#31650=EDGE_CURVE('',#18255,#17835,#11254,.T.); -#31656=ADVANCED_FACE('',(#31655),#31648,.F.); -#31663=EDGE_CURVE('',#18253,#17833,#11258,.T.); -#31669=ADVANCED_FACE('',(#31668),#31661,.F.); -#31676=EDGE_CURVE('',#18251,#17831,#11262,.T.); -#31682=ADVANCED_FACE('',(#31681),#31674,.F.); -#31689=EDGE_CURVE('',#18249,#17829,#11266,.T.); -#31695=ADVANCED_FACE('',(#31694),#31687,.F.); -#31702=EDGE_CURVE('',#18247,#17827,#11270,.T.); -#31708=ADVANCED_FACE('',(#31707),#31700,.F.); -#31715=EDGE_CURVE('',#18245,#17825,#11274,.T.); -#31721=ADVANCED_FACE('',(#31720),#31713,.F.); -#31728=EDGE_CURVE('',#18243,#17823,#11278,.T.); -#31734=ADVANCED_FACE('',(#31733),#31726,.F.); -#31741=EDGE_CURVE('',#18241,#17821,#11282,.T.); -#31747=ADVANCED_FACE('',(#31746),#31739,.F.); -#31754=EDGE_CURVE('',#18239,#17819,#11286,.T.); -#31760=ADVANCED_FACE('',(#31759),#31752,.F.); -#31767=EDGE_CURVE('',#18237,#17817,#11290,.T.); -#31773=ADVANCED_FACE('',(#31772),#31765,.F.); -#31780=EDGE_CURVE('',#18235,#17815,#11294,.T.); -#31786=ADVANCED_FACE('',(#31785),#31778,.F.); -#31793=EDGE_CURVE('',#18233,#17813,#11298,.T.); -#31799=ADVANCED_FACE('',(#31798),#31791,.F.); -#31806=EDGE_CURVE('',#18231,#17811,#11302,.T.); -#31812=ADVANCED_FACE('',(#31811),#31804,.F.); -#31819=EDGE_CURVE('',#18229,#17809,#11306,.T.); -#31825=ADVANCED_FACE('',(#31824),#31817,.F.); -#31832=EDGE_CURVE('',#18227,#17807,#11310,.T.); -#31838=ADVANCED_FACE('',(#31837),#31830,.F.); -#31845=EDGE_CURVE('',#18225,#17805,#11314,.T.); -#31851=ADVANCED_FACE('',(#31850),#31843,.F.); -#31858=EDGE_CURVE('',#18223,#17803,#11318,.T.); -#31864=ADVANCED_FACE('',(#31863),#31856,.F.); -#31871=EDGE_CURVE('',#18221,#17801,#11322,.T.); -#31877=ADVANCED_FACE('',(#31876),#31869,.F.); -#31884=EDGE_CURVE('',#18219,#17799,#11326,.T.); -#31890=ADVANCED_FACE('',(#31889),#31882,.F.); -#31897=EDGE_CURVE('',#18217,#17797,#11330,.T.); -#31903=ADVANCED_FACE('',(#31902),#31895,.F.); -#31910=EDGE_CURVE('',#18215,#17795,#11334,.T.); -#31916=ADVANCED_FACE('',(#31915),#31908,.F.); -#31923=EDGE_CURVE('',#18213,#17793,#11338,.T.); -#31929=ADVANCED_FACE('',(#31928),#31921,.F.); -#31936=EDGE_CURVE('',#18211,#17791,#11342,.T.); -#31942=ADVANCED_FACE('',(#31941),#31934,.F.); -#31949=EDGE_CURVE('',#18209,#17789,#11346,.T.); -#31955=ADVANCED_FACE('',(#31954),#31947,.F.); -#31962=EDGE_CURVE('',#18207,#17787,#11350,.T.); -#31968=ADVANCED_FACE('',(#31967),#31960,.F.); -#31975=EDGE_CURVE('',#18205,#17785,#11354,.T.); -#31981=ADVANCED_FACE('',(#31980),#31973,.F.); -#31988=EDGE_CURVE('',#18203,#17783,#11358,.T.); -#31994=ADVANCED_FACE('',(#31993),#31986,.F.); -#32001=EDGE_CURVE('',#18201,#17781,#11362,.T.); -#32007=ADVANCED_FACE('',(#32006),#31999,.F.); -#32014=EDGE_CURVE('',#18199,#17779,#11366,.T.); -#32020=ADVANCED_FACE('',(#32019),#32012,.F.); -#32027=EDGE_CURVE('',#18197,#17777,#11370,.T.); -#32033=ADVANCED_FACE('',(#32032),#32025,.F.); -#32040=EDGE_CURVE('',#18195,#17775,#11374,.T.); -#32046=ADVANCED_FACE('',(#32045),#32038,.F.); -#32058=ADVANCED_FACE('',(#32057),#32051,.F.); -#32065=EDGE_CURVE('',#18306,#17886,#11382,.T.); -#32068=EDGE_CURVE('',#18307,#17887,#11490,.T.); -#32072=ADVANCED_FACE('',(#32071),#32063,.F.); -#32079=EDGE_CURVE('',#18359,#17939,#11386,.T.); -#32085=ADVANCED_FACE('',(#32084),#32077,.F.); -#32092=EDGE_CURVE('',#18357,#17937,#11390,.T.); -#32098=ADVANCED_FACE('',(#32097),#32090,.F.); -#32105=EDGE_CURVE('',#18355,#17935,#11394,.T.); -#32111=ADVANCED_FACE('',(#32110),#32103,.F.); -#32118=EDGE_CURVE('',#18353,#17933,#11398,.T.); -#32124=ADVANCED_FACE('',(#32123),#32116,.F.); -#32131=EDGE_CURVE('',#18351,#17931,#11402,.T.); -#32137=ADVANCED_FACE('',(#32136),#32129,.F.); -#32144=EDGE_CURVE('',#18349,#17929,#11406,.T.); -#32150=ADVANCED_FACE('',(#32149),#32142,.F.); -#32157=EDGE_CURVE('',#18347,#17927,#11410,.T.); -#32163=ADVANCED_FACE('',(#32162),#32155,.F.); -#32170=EDGE_CURVE('',#18345,#17925,#11414,.T.); -#32176=ADVANCED_FACE('',(#32175),#32168,.F.); -#32183=EDGE_CURVE('',#18343,#17923,#11418,.T.); -#32189=ADVANCED_FACE('',(#32188),#32181,.F.); -#32196=EDGE_CURVE('',#18341,#17921,#11422,.T.); -#32202=ADVANCED_FACE('',(#32201),#32194,.F.); -#32209=EDGE_CURVE('',#18339,#17919,#11426,.T.); -#32215=ADVANCED_FACE('',(#32214),#32207,.F.); -#32222=EDGE_CURVE('',#18337,#17917,#11430,.T.); -#32228=ADVANCED_FACE('',(#32227),#32220,.F.); -#32235=EDGE_CURVE('',#18335,#17915,#11434,.T.); -#32241=ADVANCED_FACE('',(#32240),#32233,.F.); -#32248=EDGE_CURVE('',#18333,#17913,#11438,.T.); -#32254=ADVANCED_FACE('',(#32253),#32246,.F.); -#32261=EDGE_CURVE('',#18331,#17911,#11442,.T.); -#32267=ADVANCED_FACE('',(#32266),#32259,.F.); -#32274=EDGE_CURVE('',#18329,#17909,#11446,.T.); -#32280=ADVANCED_FACE('',(#32279),#32272,.F.); -#32287=EDGE_CURVE('',#18327,#17907,#11450,.T.); -#32293=ADVANCED_FACE('',(#32292),#32285,.F.); -#32300=EDGE_CURVE('',#18325,#17905,#11454,.T.); -#32306=ADVANCED_FACE('',(#32305),#32298,.F.); -#32313=EDGE_CURVE('',#18323,#17903,#11458,.T.); -#32319=ADVANCED_FACE('',(#32318),#32311,.F.); -#32326=EDGE_CURVE('',#18321,#17901,#11462,.T.); -#32332=ADVANCED_FACE('',(#32331),#32324,.F.); -#32339=EDGE_CURVE('',#18319,#17899,#11466,.T.); -#32345=ADVANCED_FACE('',(#32344),#32337,.F.); -#32352=EDGE_CURVE('',#18317,#17897,#11470,.T.); -#32358=ADVANCED_FACE('',(#32357),#32350,.F.); -#32365=EDGE_CURVE('',#18315,#17895,#11474,.T.); -#32371=ADVANCED_FACE('',(#32370),#32363,.F.); -#32378=EDGE_CURVE('',#18313,#17893,#11478,.T.); -#32384=ADVANCED_FACE('',(#32383),#32376,.F.); -#32391=EDGE_CURVE('',#18311,#17891,#11482,.T.); -#32397=ADVANCED_FACE('',(#32396),#32389,.F.); -#32404=EDGE_CURVE('',#18309,#17889,#11486,.T.); -#32410=ADVANCED_FACE('',(#32409),#32402,.F.); -#32422=ADVANCED_FACE('',(#32421),#32415,.F.); -#32429=EDGE_CURVE('',#18362,#17942,#11494,.T.); -#32432=EDGE_CURVE('',#18363,#17943,#11538,.T.); -#32436=ADVANCED_FACE('',(#32435),#32427,.F.); -#32443=EDGE_CURVE('',#18383,#17963,#11498,.T.); -#32449=ADVANCED_FACE('',(#32448),#32441,.F.); -#32456=EDGE_CURVE('',#18381,#17961,#11502,.T.); -#32462=ADVANCED_FACE('',(#32461),#32454,.F.); -#32469=EDGE_CURVE('',#18379,#17959,#11506,.T.); -#32475=ADVANCED_FACE('',(#32474),#32467,.F.); -#32482=EDGE_CURVE('',#18377,#17957,#11510,.T.); -#32488=ADVANCED_FACE('',(#32487),#32480,.F.); -#32495=EDGE_CURVE('',#18375,#17955,#11514,.T.); -#32501=ADVANCED_FACE('',(#32500),#32493,.F.); -#32508=EDGE_CURVE('',#18373,#17953,#11518,.T.); -#32514=ADVANCED_FACE('',(#32513),#32506,.F.); -#32521=EDGE_CURVE('',#18371,#17951,#11522,.T.); -#32527=ADVANCED_FACE('',(#32526),#32519,.F.); -#32534=EDGE_CURVE('',#18369,#17949,#11526,.T.); -#32540=ADVANCED_FACE('',(#32539),#32532,.F.); -#32547=EDGE_CURVE('',#18367,#17947,#11530,.T.); -#32553=ADVANCED_FACE('',(#32552),#32545,.F.); -#32560=EDGE_CURVE('',#18365,#17945,#11534,.T.); -#32566=ADVANCED_FACE('',(#32565),#32558,.F.); -#32578=ADVANCED_FACE('',(#32577),#32571,.F.); -#32585=EDGE_CURVE('',#20284,#18642,#11542,.T.); -#32588=EDGE_CURVE('',#20285,#18643,#11578,.T.); -#32592=ADVANCED_FACE('',(#32591),#32583,.F.); -#32599=EDGE_CURVE('',#20301,#18659,#11546,.T.); -#32605=ADVANCED_FACE('',(#32604),#32597,.F.); -#32612=EDGE_CURVE('',#20299,#18657,#11550,.T.); -#32618=ADVANCED_FACE('',(#32617),#32610,.F.); -#32625=EDGE_CURVE('',#20297,#18655,#11554,.T.); -#32631=ADVANCED_FACE('',(#32630),#32623,.F.); -#32638=EDGE_CURVE('',#20295,#18653,#11558,.T.); -#32644=ADVANCED_FACE('',(#32643),#32636,.F.); -#32651=EDGE_CURVE('',#20293,#18651,#11562,.T.); -#32657=ADVANCED_FACE('',(#32656),#32649,.F.); -#32664=EDGE_CURVE('',#20291,#18649,#11566,.T.); -#32670=ADVANCED_FACE('',(#32669),#32662,.F.); -#32677=EDGE_CURVE('',#20289,#18647,#11570,.T.); -#32683=ADVANCED_FACE('',(#32682),#32675,.F.); -#32690=EDGE_CURVE('',#20287,#18645,#11574,.T.); -#32696=ADVANCED_FACE('',(#32695),#32688,.F.); -#32708=ADVANCED_FACE('',(#32707),#32701,.F.); -#32715=EDGE_CURVE('',#20304,#18662,#11582,.T.); -#32718=EDGE_CURVE('',#20305,#18663,#11738,.T.); -#32722=ADVANCED_FACE('',(#32721),#32713,.F.); -#32729=EDGE_CURVE('',#20381,#18739,#11586,.T.); -#32735=ADVANCED_FACE('',(#32734),#32727,.F.); -#32742=EDGE_CURVE('',#20379,#18737,#11590,.T.); -#32748=ADVANCED_FACE('',(#32747),#32740,.F.); -#32755=EDGE_CURVE('',#20377,#18735,#11594,.T.); -#32761=ADVANCED_FACE('',(#32760),#32753,.F.); -#32768=EDGE_CURVE('',#20375,#18733,#11598,.T.); -#32774=ADVANCED_FACE('',(#32773),#32766,.F.); -#32781=EDGE_CURVE('',#20373,#18731,#11602,.T.); -#32787=ADVANCED_FACE('',(#32786),#32779,.F.); -#32794=EDGE_CURVE('',#20371,#18729,#11606,.T.); -#32800=ADVANCED_FACE('',(#32799),#32792,.F.); -#32807=EDGE_CURVE('',#20369,#18727,#11610,.T.); -#32813=ADVANCED_FACE('',(#32812),#32805,.F.); -#32820=EDGE_CURVE('',#20367,#18725,#11614,.T.); -#32826=ADVANCED_FACE('',(#32825),#32818,.F.); -#32833=EDGE_CURVE('',#20365,#18723,#11618,.T.); -#32839=ADVANCED_FACE('',(#32838),#32831,.F.); -#32846=EDGE_CURVE('',#20363,#18721,#11622,.T.); -#32852=ADVANCED_FACE('',(#32851),#32844,.F.); -#32859=EDGE_CURVE('',#20361,#18719,#11626,.T.); -#32865=ADVANCED_FACE('',(#32864),#32857,.F.); -#32872=EDGE_CURVE('',#20359,#18717,#11630,.T.); -#32878=ADVANCED_FACE('',(#32877),#32870,.F.); -#32885=EDGE_CURVE('',#20357,#18715,#11634,.T.); -#32891=ADVANCED_FACE('',(#32890),#32883,.F.); -#32898=EDGE_CURVE('',#20355,#18713,#11638,.T.); -#32904=ADVANCED_FACE('',(#32903),#32896,.F.); -#32911=EDGE_CURVE('',#20353,#18711,#11642,.T.); -#32917=ADVANCED_FACE('',(#32916),#32909,.F.); -#32924=EDGE_CURVE('',#20351,#18709,#11646,.T.); -#32930=ADVANCED_FACE('',(#32929),#32922,.F.); -#32937=EDGE_CURVE('',#20349,#18707,#11650,.T.); -#32943=ADVANCED_FACE('',(#32942),#32935,.F.); -#32950=EDGE_CURVE('',#20347,#18705,#11654,.T.); -#32956=ADVANCED_FACE('',(#32955),#32948,.F.); -#32963=EDGE_CURVE('',#20345,#18703,#11658,.T.); -#32969=ADVANCED_FACE('',(#32968),#32961,.F.); -#32976=EDGE_CURVE('',#20343,#18701,#11662,.T.); -#32982=ADVANCED_FACE('',(#32981),#32974,.F.); -#32989=EDGE_CURVE('',#20341,#18699,#11666,.T.); -#32995=ADVANCED_FACE('',(#32994),#32987,.F.); -#33002=EDGE_CURVE('',#20339,#18697,#11670,.T.); -#33008=ADVANCED_FACE('',(#33007),#33000,.F.); -#33015=EDGE_CURVE('',#20337,#18695,#11674,.T.); -#33021=ADVANCED_FACE('',(#33020),#33013,.F.); -#33028=EDGE_CURVE('',#20335,#18693,#11678,.T.); -#33034=ADVANCED_FACE('',(#33033),#33026,.F.); -#33041=EDGE_CURVE('',#20333,#18691,#11682,.T.); -#33047=ADVANCED_FACE('',(#33046),#33039,.F.); -#33054=EDGE_CURVE('',#20331,#18689,#11686,.T.); -#33060=ADVANCED_FACE('',(#33059),#33052,.F.); -#33067=EDGE_CURVE('',#20329,#18687,#11690,.T.); -#33073=ADVANCED_FACE('',(#33072),#33065,.F.); -#33080=EDGE_CURVE('',#20327,#18685,#11694,.T.); -#33086=ADVANCED_FACE('',(#33085),#33078,.F.); -#33093=EDGE_CURVE('',#20325,#18683,#11698,.T.); -#33099=ADVANCED_FACE('',(#33098),#33091,.F.); -#33106=EDGE_CURVE('',#20323,#18681,#11702,.T.); -#33112=ADVANCED_FACE('',(#33111),#33104,.F.); -#33119=EDGE_CURVE('',#20321,#18679,#11706,.T.); -#33125=ADVANCED_FACE('',(#33124),#33117,.F.); -#33132=EDGE_CURVE('',#20319,#18677,#11710,.T.); -#33138=ADVANCED_FACE('',(#33137),#33130,.F.); -#33145=EDGE_CURVE('',#20317,#18675,#11714,.T.); -#33151=ADVANCED_FACE('',(#33150),#33143,.F.); -#33158=EDGE_CURVE('',#20315,#18673,#11718,.T.); -#33164=ADVANCED_FACE('',(#33163),#33156,.F.); -#33171=EDGE_CURVE('',#20313,#18671,#11722,.T.); -#33177=ADVANCED_FACE('',(#33176),#33169,.F.); -#33184=EDGE_CURVE('',#20311,#18669,#11726,.T.); -#33190=ADVANCED_FACE('',(#33189),#33182,.F.); -#33197=EDGE_CURVE('',#20309,#18667,#11730,.T.); -#33203=ADVANCED_FACE('',(#33202),#33195,.F.); -#33210=EDGE_CURVE('',#20307,#18665,#11734,.T.); -#33216=ADVANCED_FACE('',(#33215),#33208,.F.); -#33228=ADVANCED_FACE('',(#33227),#33221,.F.); -#33235=EDGE_CURVE('',#20384,#18742,#11742,.T.); -#33238=EDGE_CURVE('',#20385,#18743,#11898,.T.); -#33242=ADVANCED_FACE('',(#33241),#33233,.F.); -#33249=EDGE_CURVE('',#20461,#18819,#11746,.T.); -#33255=ADVANCED_FACE('',(#33254),#33247,.F.); -#33262=EDGE_CURVE('',#20459,#18817,#11750,.T.); -#33268=ADVANCED_FACE('',(#33267),#33260,.F.); -#33275=EDGE_CURVE('',#20457,#18815,#11754,.T.); -#33281=ADVANCED_FACE('',(#33280),#33273,.F.); -#33288=EDGE_CURVE('',#20455,#18813,#11758,.T.); -#33294=ADVANCED_FACE('',(#33293),#33286,.F.); -#33301=EDGE_CURVE('',#20453,#18811,#11762,.T.); -#33307=ADVANCED_FACE('',(#33306),#33299,.F.); -#33314=EDGE_CURVE('',#20451,#18809,#11766,.T.); -#33320=ADVANCED_FACE('',(#33319),#33312,.F.); -#33327=EDGE_CURVE('',#20449,#18807,#11770,.T.); -#33333=ADVANCED_FACE('',(#33332),#33325,.F.); -#33340=EDGE_CURVE('',#20447,#18805,#11774,.T.); -#33346=ADVANCED_FACE('',(#33345),#33338,.F.); -#33353=EDGE_CURVE('',#20445,#18803,#11778,.T.); -#33359=ADVANCED_FACE('',(#33358),#33351,.F.); -#33366=EDGE_CURVE('',#20443,#18801,#11782,.T.); -#33372=ADVANCED_FACE('',(#33371),#33364,.F.); -#33379=EDGE_CURVE('',#20441,#18799,#11786,.T.); -#33385=ADVANCED_FACE('',(#33384),#33377,.F.); -#33392=EDGE_CURVE('',#20439,#18797,#11790,.T.); -#33398=ADVANCED_FACE('',(#33397),#33390,.F.); -#33405=EDGE_CURVE('',#20437,#18795,#11794,.T.); -#33411=ADVANCED_FACE('',(#33410),#33403,.F.); -#33418=EDGE_CURVE('',#20435,#18793,#11798,.T.); -#33424=ADVANCED_FACE('',(#33423),#33416,.F.); -#33431=EDGE_CURVE('',#20433,#18791,#11802,.T.); -#33437=ADVANCED_FACE('',(#33436),#33429,.F.); -#33444=EDGE_CURVE('',#20431,#18789,#11806,.T.); -#33450=ADVANCED_FACE('',(#33449),#33442,.F.); -#33457=EDGE_CURVE('',#20429,#18787,#11810,.T.); -#33463=ADVANCED_FACE('',(#33462),#33455,.F.); -#33470=EDGE_CURVE('',#20427,#18785,#11814,.T.); -#33476=ADVANCED_FACE('',(#33475),#33468,.F.); -#33483=EDGE_CURVE('',#20425,#18783,#11818,.T.); -#33489=ADVANCED_FACE('',(#33488),#33481,.F.); -#33496=EDGE_CURVE('',#20423,#18781,#11822,.T.); -#33502=ADVANCED_FACE('',(#33501),#33494,.F.); -#33509=EDGE_CURVE('',#20421,#18779,#11826,.T.); -#33515=ADVANCED_FACE('',(#33514),#33507,.F.); -#33522=EDGE_CURVE('',#20419,#18777,#11830,.T.); -#33528=ADVANCED_FACE('',(#33527),#33520,.F.); -#33535=EDGE_CURVE('',#20417,#18775,#11834,.T.); -#33541=ADVANCED_FACE('',(#33540),#33533,.F.); -#33548=EDGE_CURVE('',#20415,#18773,#11838,.T.); -#33554=ADVANCED_FACE('',(#33553),#33546,.F.); -#33561=EDGE_CURVE('',#20413,#18771,#11842,.T.); -#33567=ADVANCED_FACE('',(#33566),#33559,.F.); -#33574=EDGE_CURVE('',#20411,#18769,#11846,.T.); -#33580=ADVANCED_FACE('',(#33579),#33572,.F.); -#33587=EDGE_CURVE('',#20409,#18767,#11850,.T.); -#33593=ADVANCED_FACE('',(#33592),#33585,.F.); -#33600=EDGE_CURVE('',#20407,#18765,#11854,.T.); -#33606=ADVANCED_FACE('',(#33605),#33598,.F.); -#33613=EDGE_CURVE('',#20405,#18763,#11858,.T.); -#33619=ADVANCED_FACE('',(#33618),#33611,.F.); -#33626=EDGE_CURVE('',#20403,#18761,#11862,.T.); -#33632=ADVANCED_FACE('',(#33631),#33624,.F.); -#33639=EDGE_CURVE('',#20401,#18759,#11866,.T.); -#33645=ADVANCED_FACE('',(#33644),#33637,.F.); -#33652=EDGE_CURVE('',#20399,#18757,#11870,.T.); -#33658=ADVANCED_FACE('',(#33657),#33650,.F.); -#33665=EDGE_CURVE('',#20397,#18755,#11874,.T.); -#33671=ADVANCED_FACE('',(#33670),#33663,.F.); -#33678=EDGE_CURVE('',#20395,#18753,#11878,.T.); -#33684=ADVANCED_FACE('',(#33683),#33676,.F.); -#33691=EDGE_CURVE('',#20393,#18751,#11882,.T.); -#33697=ADVANCED_FACE('',(#33696),#33689,.F.); -#33704=EDGE_CURVE('',#20391,#18749,#11886,.T.); -#33710=ADVANCED_FACE('',(#33709),#33702,.F.); -#33717=EDGE_CURVE('',#20389,#18747,#11890,.T.); -#33723=ADVANCED_FACE('',(#33722),#33715,.F.); -#33730=EDGE_CURVE('',#20387,#18745,#11894,.T.); -#33736=ADVANCED_FACE('',(#33735),#33728,.F.); -#33748=ADVANCED_FACE('',(#33747),#33741,.F.); -#33755=EDGE_CURVE('',#20464,#18822,#11902,.T.); -#33758=EDGE_CURVE('',#20465,#18823,#11914,.T.); -#33762=ADVANCED_FACE('',(#33761),#33753,.F.); -#33769=EDGE_CURVE('',#20469,#18827,#11906,.T.); -#33775=ADVANCED_FACE('',(#33774),#33767,.F.); -#33782=EDGE_CURVE('',#20467,#18825,#11910,.T.); -#33788=ADVANCED_FACE('',(#33787),#33780,.F.); -#33800=ADVANCED_FACE('',(#33799),#33793,.F.); -#33807=EDGE_CURVE('',#20472,#18830,#11918,.T.); -#33810=EDGE_CURVE('',#20473,#18831,#11970,.T.); -#33814=ADVANCED_FACE('',(#33813),#33805,.F.); -#33821=EDGE_CURVE('',#20497,#18855,#11922,.T.); -#33827=ADVANCED_FACE('',(#33826),#33819,.F.); -#33834=EDGE_CURVE('',#20495,#18853,#11926,.T.); -#33840=ADVANCED_FACE('',(#33839),#33832,.F.); -#33847=EDGE_CURVE('',#20493,#18851,#11930,.T.); -#33853=ADVANCED_FACE('',(#33852),#33845,.F.); -#33860=EDGE_CURVE('',#20491,#18849,#11934,.T.); -#33866=ADVANCED_FACE('',(#33865),#33858,.F.); -#33873=EDGE_CURVE('',#20489,#18847,#11938,.T.); -#33879=ADVANCED_FACE('',(#33878),#33871,.F.); -#33886=EDGE_CURVE('',#20487,#18845,#11942,.T.); -#33892=ADVANCED_FACE('',(#33891),#33884,.F.); -#33899=EDGE_CURVE('',#20485,#18843,#11946,.T.); -#33905=ADVANCED_FACE('',(#33904),#33897,.F.); -#33912=EDGE_CURVE('',#20483,#18841,#11950,.T.); -#33918=ADVANCED_FACE('',(#33917),#33910,.F.); -#33925=EDGE_CURVE('',#20481,#18839,#11954,.T.); -#33931=ADVANCED_FACE('',(#33930),#33923,.F.); -#33938=EDGE_CURVE('',#20479,#18837,#11958,.T.); -#33944=ADVANCED_FACE('',(#33943),#33936,.F.); -#33951=EDGE_CURVE('',#20477,#18835,#11962,.T.); -#33957=ADVANCED_FACE('',(#33956),#33949,.F.); -#33964=EDGE_CURVE('',#20475,#18833,#11966,.T.); -#33970=ADVANCED_FACE('',(#33969),#33962,.F.); -#33982=ADVANCED_FACE('',(#33981),#33975,.F.); -#33989=EDGE_CURVE('',#20500,#18858,#11974,.T.); -#33992=EDGE_CURVE('',#20501,#18859,#12018,.T.); -#33996=ADVANCED_FACE('',(#33995),#33987,.F.); -#34003=EDGE_CURVE('',#20521,#18879,#11978,.T.); -#34009=ADVANCED_FACE('',(#34008),#34001,.F.); -#34016=EDGE_CURVE('',#20519,#18877,#11982,.T.); -#34022=ADVANCED_FACE('',(#34021),#34014,.F.); -#34029=EDGE_CURVE('',#20517,#18875,#11986,.T.); -#34035=ADVANCED_FACE('',(#34034),#34027,.F.); -#34042=EDGE_CURVE('',#20515,#18873,#11990,.T.); -#34048=ADVANCED_FACE('',(#34047),#34040,.F.); -#34055=EDGE_CURVE('',#20513,#18871,#11994,.T.); -#34061=ADVANCED_FACE('',(#34060),#34053,.F.); -#34068=EDGE_CURVE('',#20511,#18869,#11998,.T.); -#34074=ADVANCED_FACE('',(#34073),#34066,.F.); -#34081=EDGE_CURVE('',#20509,#18867,#12002,.T.); -#34087=ADVANCED_FACE('',(#34086),#34079,.F.); -#34094=EDGE_CURVE('',#20507,#18865,#12006,.T.); -#34100=ADVANCED_FACE('',(#34099),#34092,.F.); -#34107=EDGE_CURVE('',#20505,#18863,#12010,.T.); -#34113=ADVANCED_FACE('',(#34112),#34105,.F.); -#34120=EDGE_CURVE('',#20503,#18861,#12014,.T.); -#34126=ADVANCED_FACE('',(#34125),#34118,.F.); -#34138=ADVANCED_FACE('',(#34137),#34131,.F.); -#34145=EDGE_CURVE('',#20524,#18882,#12022,.T.); -#34148=EDGE_CURVE('',#20525,#18883,#12034,.T.); -#34152=ADVANCED_FACE('',(#34151),#34143,.F.); -#34159=EDGE_CURVE('',#20529,#18887,#12026,.T.); -#34165=ADVANCED_FACE('',(#34164),#34157,.F.); -#34172=EDGE_CURVE('',#20527,#18885,#12030,.T.); -#34178=ADVANCED_FACE('',(#34177),#34170,.F.); -#34190=ADVANCED_FACE('',(#34189),#34183,.F.); -#34197=EDGE_CURVE('',#20532,#18890,#12038,.T.); -#34200=EDGE_CURVE('',#20533,#18891,#12050,.T.); -#34204=ADVANCED_FACE('',(#34203),#34195,.F.); -#34211=EDGE_CURVE('',#20537,#18895,#12042,.T.); -#34217=ADVANCED_FACE('',(#34216),#34209,.F.); -#34224=EDGE_CURVE('',#20535,#18893,#12046,.T.); -#34230=ADVANCED_FACE('',(#34229),#34222,.F.); -#34242=ADVANCED_FACE('',(#34241),#34235,.F.); -#34249=EDGE_CURVE('',#20540,#18898,#12054,.T.); -#34252=EDGE_CURVE('',#20541,#18899,#12098,.T.); -#34256=ADVANCED_FACE('',(#34255),#34247,.F.); -#34263=EDGE_CURVE('',#20561,#18919,#12058,.T.); -#34269=ADVANCED_FACE('',(#34268),#34261,.F.); -#34276=EDGE_CURVE('',#20559,#18917,#12062,.T.); -#34282=ADVANCED_FACE('',(#34281),#34274,.F.); -#34289=EDGE_CURVE('',#20557,#18915,#12066,.T.); -#34295=ADVANCED_FACE('',(#34294),#34287,.F.); -#34302=EDGE_CURVE('',#20555,#18913,#12070,.T.); -#34308=ADVANCED_FACE('',(#34307),#34300,.F.); -#34315=EDGE_CURVE('',#20553,#18911,#12074,.T.); -#34321=ADVANCED_FACE('',(#34320),#34313,.F.); -#34328=EDGE_CURVE('',#20551,#18909,#12078,.T.); -#34334=ADVANCED_FACE('',(#34333),#34326,.F.); -#34341=EDGE_CURVE('',#20549,#18907,#12082,.T.); -#34347=ADVANCED_FACE('',(#34346),#34339,.F.); -#34354=EDGE_CURVE('',#20547,#18905,#12086,.T.); -#34360=ADVANCED_FACE('',(#34359),#34352,.F.); -#34367=EDGE_CURVE('',#20545,#18903,#12090,.T.); -#34373=ADVANCED_FACE('',(#34372),#34365,.F.); -#34380=EDGE_CURVE('',#20543,#18901,#12094,.T.); -#34386=ADVANCED_FACE('',(#34385),#34378,.F.); -#34398=ADVANCED_FACE('',(#34397),#34391,.F.); -#34405=EDGE_CURVE('',#20564,#18922,#12102,.T.); -#34408=EDGE_CURVE('',#20565,#18923,#12234,.T.); -#34412=ADVANCED_FACE('',(#34411),#34403,.F.); -#34419=EDGE_CURVE('',#20629,#18987,#12106,.T.); -#34425=ADVANCED_FACE('',(#34424),#34417,.F.); -#34432=EDGE_CURVE('',#20627,#18985,#12110,.T.); -#34438=ADVANCED_FACE('',(#34437),#34430,.F.); -#34445=EDGE_CURVE('',#20625,#18983,#12114,.T.); -#34451=ADVANCED_FACE('',(#34450),#34443,.F.); -#34458=EDGE_CURVE('',#20623,#18981,#12118,.T.); -#34464=ADVANCED_FACE('',(#34463),#34456,.F.); -#34471=EDGE_CURVE('',#20621,#18979,#12122,.T.); -#34477=ADVANCED_FACE('',(#34476),#34469,.F.); -#34484=EDGE_CURVE('',#20619,#18977,#12126,.T.); -#34490=ADVANCED_FACE('',(#34489),#34482,.F.); -#34497=EDGE_CURVE('',#20617,#18975,#12130,.T.); -#34503=ADVANCED_FACE('',(#34502),#34495,.F.); -#34510=EDGE_CURVE('',#20615,#18973,#12134,.T.); -#34516=ADVANCED_FACE('',(#34515),#34508,.F.); -#34523=EDGE_CURVE('',#20613,#18971,#12138,.T.); -#34529=ADVANCED_FACE('',(#34528),#34521,.F.); -#34536=EDGE_CURVE('',#20611,#18969,#12142,.T.); -#34542=ADVANCED_FACE('',(#34541),#34534,.F.); -#34549=EDGE_CURVE('',#20609,#18967,#12146,.T.); -#34555=ADVANCED_FACE('',(#34554),#34547,.F.); -#34562=EDGE_CURVE('',#20607,#18965,#12150,.T.); -#34568=ADVANCED_FACE('',(#34567),#34560,.F.); -#34575=EDGE_CURVE('',#20605,#18963,#12154,.T.); -#34581=ADVANCED_FACE('',(#34580),#34573,.F.); -#34588=EDGE_CURVE('',#20603,#18961,#12158,.T.); -#34594=ADVANCED_FACE('',(#34593),#34586,.F.); -#34601=EDGE_CURVE('',#20601,#18959,#12162,.T.); -#34607=ADVANCED_FACE('',(#34606),#34599,.F.); -#34614=EDGE_CURVE('',#20599,#18957,#12166,.T.); -#34620=ADVANCED_FACE('',(#34619),#34612,.F.); -#34627=EDGE_CURVE('',#20597,#18955,#12170,.T.); -#34633=ADVANCED_FACE('',(#34632),#34625,.F.); -#34640=EDGE_CURVE('',#20595,#18953,#12174,.T.); -#34646=ADVANCED_FACE('',(#34645),#34638,.F.); -#34653=EDGE_CURVE('',#20593,#18951,#12178,.T.); -#34659=ADVANCED_FACE('',(#34658),#34651,.F.); -#34666=EDGE_CURVE('',#20591,#18949,#12182,.T.); -#34672=ADVANCED_FACE('',(#34671),#34664,.F.); -#34679=EDGE_CURVE('',#20589,#18947,#12186,.T.); -#34685=ADVANCED_FACE('',(#34684),#34677,.F.); -#34692=EDGE_CURVE('',#20587,#18945,#12190,.T.); -#34698=ADVANCED_FACE('',(#34697),#34690,.F.); -#34705=EDGE_CURVE('',#20585,#18943,#12194,.T.); -#34711=ADVANCED_FACE('',(#34710),#34703,.F.); -#34718=EDGE_CURVE('',#20583,#18941,#12198,.T.); -#34724=ADVANCED_FACE('',(#34723),#34716,.F.); -#34731=EDGE_CURVE('',#20581,#18939,#12202,.T.); -#34737=ADVANCED_FACE('',(#34736),#34729,.F.); -#34744=EDGE_CURVE('',#20579,#18937,#12206,.T.); -#34750=ADVANCED_FACE('',(#34749),#34742,.F.); -#34757=EDGE_CURVE('',#20577,#18935,#12210,.T.); -#34763=ADVANCED_FACE('',(#34762),#34755,.F.); -#34770=EDGE_CURVE('',#20575,#18933,#12214,.T.); -#34776=ADVANCED_FACE('',(#34775),#34768,.F.); -#34783=EDGE_CURVE('',#20573,#18931,#12218,.T.); -#34789=ADVANCED_FACE('',(#34788),#34781,.F.); -#34796=EDGE_CURVE('',#20571,#18929,#12222,.T.); -#34802=ADVANCED_FACE('',(#34801),#34794,.F.); -#34809=EDGE_CURVE('',#20569,#18927,#12226,.T.); -#34815=ADVANCED_FACE('',(#34814),#34807,.F.); -#34822=EDGE_CURVE('',#20567,#18925,#12230,.T.); -#34828=ADVANCED_FACE('',(#34827),#34820,.F.); -#34840=ADVANCED_FACE('',(#34839),#34833,.F.); -#34847=EDGE_CURVE('',#20632,#18990,#12238,.T.); -#34850=EDGE_CURVE('',#20633,#18991,#12298,.T.); -#34854=ADVANCED_FACE('',(#34853),#34845,.F.); -#34861=EDGE_CURVE('',#20661,#19019,#12242,.T.); -#34867=ADVANCED_FACE('',(#34866),#34859,.F.); -#34874=EDGE_CURVE('',#20659,#19017,#12246,.T.); -#34880=ADVANCED_FACE('',(#34879),#34872,.F.); -#34887=EDGE_CURVE('',#20657,#19015,#12250,.T.); -#34893=ADVANCED_FACE('',(#34892),#34885,.F.); -#34900=EDGE_CURVE('',#20655,#19013,#12254,.T.); -#34906=ADVANCED_FACE('',(#34905),#34898,.F.); -#34913=EDGE_CURVE('',#20653,#19011,#12258,.T.); -#34919=ADVANCED_FACE('',(#34918),#34911,.F.); -#34926=EDGE_CURVE('',#20651,#19009,#12262,.T.); -#34932=ADVANCED_FACE('',(#34931),#34924,.F.); -#34939=EDGE_CURVE('',#20649,#19007,#12266,.T.); -#34945=ADVANCED_FACE('',(#34944),#34937,.F.); -#34952=EDGE_CURVE('',#20647,#19005,#12270,.T.); -#34958=ADVANCED_FACE('',(#34957),#34950,.F.); -#34965=EDGE_CURVE('',#20645,#19003,#12274,.T.); -#34971=ADVANCED_FACE('',(#34970),#34963,.F.); -#34978=EDGE_CURVE('',#20643,#19001,#12278,.T.); -#34984=ADVANCED_FACE('',(#34983),#34976,.F.); -#34991=EDGE_CURVE('',#20641,#18999,#12282,.T.); -#34997=ADVANCED_FACE('',(#34996),#34989,.F.); -#35004=EDGE_CURVE('',#20639,#18997,#12286,.T.); -#35010=ADVANCED_FACE('',(#35009),#35002,.F.); -#35017=EDGE_CURVE('',#20637,#18995,#12290,.T.); -#35023=ADVANCED_FACE('',(#35022),#35015,.F.); -#35030=EDGE_CURVE('',#20635,#18993,#12294,.T.); -#35036=ADVANCED_FACE('',(#35035),#35028,.F.); -#35048=ADVANCED_FACE('',(#35047),#35041,.F.); -#35055=EDGE_CURVE('',#20664,#19022,#12302,.T.); -#35058=EDGE_CURVE('',#20665,#19023,#12362,.T.); -#35062=ADVANCED_FACE('',(#35061),#35053,.F.); -#35069=EDGE_CURVE('',#20693,#19051,#12306,.T.); -#35075=ADVANCED_FACE('',(#35074),#35067,.F.); -#35082=EDGE_CURVE('',#20691,#19049,#12310,.T.); -#35088=ADVANCED_FACE('',(#35087),#35080,.F.); -#35095=EDGE_CURVE('',#20689,#19047,#12314,.T.); -#35101=ADVANCED_FACE('',(#35100),#35093,.F.); -#35108=EDGE_CURVE('',#20687,#19045,#12318,.T.); -#35114=ADVANCED_FACE('',(#35113),#35106,.F.); -#35121=EDGE_CURVE('',#20685,#19043,#12322,.T.); -#35127=ADVANCED_FACE('',(#35126),#35119,.F.); -#35134=EDGE_CURVE('',#20683,#19041,#12326,.T.); -#35140=ADVANCED_FACE('',(#35139),#35132,.F.); -#35147=EDGE_CURVE('',#20681,#19039,#12330,.T.); -#35153=ADVANCED_FACE('',(#35152),#35145,.F.); -#35160=EDGE_CURVE('',#20679,#19037,#12334,.T.); -#35166=ADVANCED_FACE('',(#35165),#35158,.F.); -#35173=EDGE_CURVE('',#20677,#19035,#12338,.T.); -#35179=ADVANCED_FACE('',(#35178),#35171,.F.); -#35186=EDGE_CURVE('',#20675,#19033,#12342,.T.); -#35192=ADVANCED_FACE('',(#35191),#35184,.F.); -#35199=EDGE_CURVE('',#20673,#19031,#12346,.T.); -#35205=ADVANCED_FACE('',(#35204),#35197,.F.); -#35212=EDGE_CURVE('',#20671,#19029,#12350,.T.); -#35218=ADVANCED_FACE('',(#35217),#35210,.F.); -#35225=EDGE_CURVE('',#20669,#19027,#12354,.T.); -#35231=ADVANCED_FACE('',(#35230),#35223,.F.); -#35238=EDGE_CURVE('',#20667,#19025,#12358,.T.); -#35244=ADVANCED_FACE('',(#35243),#35236,.F.); -#35256=ADVANCED_FACE('',(#35255),#35249,.F.); -#35263=EDGE_CURVE('',#20696,#19054,#12366,.T.); -#35266=EDGE_CURVE('',#20697,#19055,#12414,.T.); -#35270=ADVANCED_FACE('',(#35269),#35261,.F.); -#35277=EDGE_CURVE('',#20719,#19077,#12370,.T.); -#35283=ADVANCED_FACE('',(#35282),#35275,.F.); -#35290=EDGE_CURVE('',#20717,#19075,#12374,.T.); -#35296=ADVANCED_FACE('',(#35295),#35288,.F.); -#35303=EDGE_CURVE('',#20715,#19073,#12378,.T.); -#35309=ADVANCED_FACE('',(#35308),#35301,.F.); -#35316=EDGE_CURVE('',#20713,#19071,#12382,.T.); -#35322=ADVANCED_FACE('',(#35321),#35314,.F.); -#35329=EDGE_CURVE('',#20711,#19069,#12386,.T.); -#35335=ADVANCED_FACE('',(#35334),#35327,.F.); -#35342=EDGE_CURVE('',#20709,#19067,#12390,.T.); -#35348=ADVANCED_FACE('',(#35347),#35340,.F.); -#35355=EDGE_CURVE('',#20707,#19065,#12394,.T.); -#35361=ADVANCED_FACE('',(#35360),#35353,.F.); -#35368=EDGE_CURVE('',#20705,#19063,#12398,.T.); -#35374=ADVANCED_FACE('',(#35373),#35366,.F.); -#35381=EDGE_CURVE('',#20703,#19061,#12402,.T.); -#35387=ADVANCED_FACE('',(#35386),#35379,.F.); -#35394=EDGE_CURVE('',#20701,#19059,#12406,.T.); -#35400=ADVANCED_FACE('',(#35399),#35392,.F.); -#35407=EDGE_CURVE('',#20699,#19057,#12410,.T.); -#35413=ADVANCED_FACE('',(#35412),#35405,.F.); -#35425=ADVANCED_FACE('',(#35424),#35418,.F.); -#35432=EDGE_CURVE('',#20722,#19080,#12418,.T.); -#35435=EDGE_CURVE('',#20723,#19081,#12490,.T.); -#35439=ADVANCED_FACE('',(#35438),#35430,.F.); -#35446=EDGE_CURVE('',#20757,#19115,#12422,.T.); -#35452=ADVANCED_FACE('',(#35451),#35444,.F.); -#35459=EDGE_CURVE('',#20755,#19113,#12426,.T.); -#35465=ADVANCED_FACE('',(#35464),#35457,.F.); -#35472=EDGE_CURVE('',#20753,#19111,#12430,.T.); -#35478=ADVANCED_FACE('',(#35477),#35470,.F.); -#35485=EDGE_CURVE('',#20751,#19109,#12434,.T.); -#35491=ADVANCED_FACE('',(#35490),#35483,.F.); -#35498=EDGE_CURVE('',#20749,#19107,#12438,.T.); -#35504=ADVANCED_FACE('',(#35503),#35496,.F.); -#35511=EDGE_CURVE('',#20747,#19105,#12442,.T.); -#35517=ADVANCED_FACE('',(#35516),#35509,.F.); -#35524=EDGE_CURVE('',#20745,#19103,#12446,.T.); -#35530=ADVANCED_FACE('',(#35529),#35522,.F.); -#35537=EDGE_CURVE('',#20743,#19101,#12450,.T.); -#35543=ADVANCED_FACE('',(#35542),#35535,.F.); -#35550=EDGE_CURVE('',#20741,#19099,#12454,.T.); -#35556=ADVANCED_FACE('',(#35555),#35548,.F.); -#35563=EDGE_CURVE('',#20739,#19097,#12458,.T.); -#35569=ADVANCED_FACE('',(#35568),#35561,.F.); -#35576=EDGE_CURVE('',#20737,#19095,#12462,.T.); -#35582=ADVANCED_FACE('',(#35581),#35574,.F.); -#35589=EDGE_CURVE('',#20735,#19093,#12466,.T.); -#35595=ADVANCED_FACE('',(#35594),#35587,.F.); -#35602=EDGE_CURVE('',#20733,#19091,#12470,.T.); -#35608=ADVANCED_FACE('',(#35607),#35600,.F.); -#35615=EDGE_CURVE('',#20731,#19089,#12474,.T.); -#35621=ADVANCED_FACE('',(#35620),#35613,.F.); -#35628=EDGE_CURVE('',#20729,#19087,#12478,.T.); -#35634=ADVANCED_FACE('',(#35633),#35626,.F.); -#35641=EDGE_CURVE('',#20727,#19085,#12482,.T.); -#35647=ADVANCED_FACE('',(#35646),#35639,.F.); -#35654=EDGE_CURVE('',#20725,#19083,#12486,.T.); -#35660=ADVANCED_FACE('',(#35659),#35652,.F.); -#35672=ADVANCED_FACE('',(#35671),#35665,.F.); -#35679=EDGE_CURVE('',#20760,#19118,#12494,.T.); -#35682=EDGE_CURVE('',#20761,#19119,#12530,.T.); -#35686=ADVANCED_FACE('',(#35685),#35677,.F.); -#35693=EDGE_CURVE('',#20777,#19135,#12498,.T.); -#35699=ADVANCED_FACE('',(#35698),#35691,.F.); -#35706=EDGE_CURVE('',#20775,#19133,#12502,.T.); -#35712=ADVANCED_FACE('',(#35711),#35704,.F.); -#35719=EDGE_CURVE('',#20773,#19131,#12506,.T.); -#35725=ADVANCED_FACE('',(#35724),#35717,.F.); -#35732=EDGE_CURVE('',#20771,#19129,#12510,.T.); -#35738=ADVANCED_FACE('',(#35737),#35730,.F.); -#35745=EDGE_CURVE('',#20769,#19127,#12514,.T.); -#35751=ADVANCED_FACE('',(#35750),#35743,.F.); -#35758=EDGE_CURVE('',#20767,#19125,#12518,.T.); -#35764=ADVANCED_FACE('',(#35763),#35756,.F.); -#35771=EDGE_CURVE('',#20765,#19123,#12522,.T.); -#35777=ADVANCED_FACE('',(#35776),#35769,.F.); -#35784=EDGE_CURVE('',#20763,#19121,#12526,.T.); -#35790=ADVANCED_FACE('',(#35789),#35782,.F.); -#35802=ADVANCED_FACE('',(#35801),#35795,.F.); -#35809=EDGE_CURVE('',#20780,#19138,#12534,.T.); -#35812=EDGE_CURVE('',#20781,#19139,#12570,.T.); -#35816=ADVANCED_FACE('',(#35815),#35807,.F.); -#35823=EDGE_CURVE('',#20797,#19155,#12538,.T.); -#35829=ADVANCED_FACE('',(#35828),#35821,.F.); -#35836=EDGE_CURVE('',#20795,#19153,#12542,.T.); -#35842=ADVANCED_FACE('',(#35841),#35834,.F.); -#35849=EDGE_CURVE('',#20793,#19151,#12546,.T.); -#35855=ADVANCED_FACE('',(#35854),#35847,.F.); -#35862=EDGE_CURVE('',#20791,#19149,#12550,.T.); -#35868=ADVANCED_FACE('',(#35867),#35860,.F.); -#35875=EDGE_CURVE('',#20789,#19147,#12554,.T.); -#35881=ADVANCED_FACE('',(#35880),#35873,.F.); -#35888=EDGE_CURVE('',#20787,#19145,#12558,.T.); -#35894=ADVANCED_FACE('',(#35893),#35886,.F.); -#35901=EDGE_CURVE('',#20785,#19143,#12562,.T.); -#35907=ADVANCED_FACE('',(#35906),#35899,.F.); -#35914=EDGE_CURVE('',#20783,#19141,#12566,.T.); -#35920=ADVANCED_FACE('',(#35919),#35912,.F.); -#35932=ADVANCED_FACE('',(#35931),#35925,.F.); -#35939=EDGE_CURVE('',#20800,#19158,#12574,.T.); -#35942=EDGE_CURVE('',#20801,#19159,#12602,.T.); -#35946=ADVANCED_FACE('',(#35945),#35937,.F.); -#35953=EDGE_CURVE('',#20813,#19171,#12578,.T.); -#35959=ADVANCED_FACE('',(#35958),#35951,.F.); -#35966=EDGE_CURVE('',#20811,#19169,#12582,.T.); -#35972=ADVANCED_FACE('',(#35971),#35964,.F.); -#35979=EDGE_CURVE('',#20809,#19167,#12586,.T.); -#35985=ADVANCED_FACE('',(#35984),#35977,.F.); -#35992=EDGE_CURVE('',#20807,#19165,#12590,.T.); -#35998=ADVANCED_FACE('',(#35997),#35990,.F.); -#36005=EDGE_CURVE('',#20805,#19163,#12594,.T.); -#36011=ADVANCED_FACE('',(#36010),#36003,.F.); -#36018=EDGE_CURVE('',#20803,#19161,#12598,.T.); -#36024=ADVANCED_FACE('',(#36023),#36016,.F.); -#36036=ADVANCED_FACE('',(#36035),#36029,.F.); -#36043=EDGE_CURVE('',#20816,#19174,#12606,.T.); -#36046=EDGE_CURVE('',#20817,#19175,#12738,.T.); -#36050=ADVANCED_FACE('',(#36049),#36041,.F.); -#36057=EDGE_CURVE('',#20881,#19239,#12610,.T.); -#36063=ADVANCED_FACE('',(#36062),#36055,.F.); -#36070=EDGE_CURVE('',#20879,#19237,#12614,.T.); -#36076=ADVANCED_FACE('',(#36075),#36068,.F.); -#36083=EDGE_CURVE('',#20877,#19235,#12618,.T.); -#36089=ADVANCED_FACE('',(#36088),#36081,.F.); -#36096=EDGE_CURVE('',#20875,#19233,#12622,.T.); -#36102=ADVANCED_FACE('',(#36101),#36094,.F.); -#36109=EDGE_CURVE('',#20873,#19231,#12626,.T.); -#36115=ADVANCED_FACE('',(#36114),#36107,.F.); -#36122=EDGE_CURVE('',#20871,#19229,#12630,.T.); -#36128=ADVANCED_FACE('',(#36127),#36120,.F.); -#36135=EDGE_CURVE('',#20869,#19227,#12634,.T.); -#36141=ADVANCED_FACE('',(#36140),#36133,.F.); -#36148=EDGE_CURVE('',#20867,#19225,#12638,.T.); -#36154=ADVANCED_FACE('',(#36153),#36146,.F.); -#36161=EDGE_CURVE('',#20865,#19223,#12642,.T.); -#36167=ADVANCED_FACE('',(#36166),#36159,.F.); -#36174=EDGE_CURVE('',#20863,#19221,#12646,.T.); -#36180=ADVANCED_FACE('',(#36179),#36172,.F.); -#36187=EDGE_CURVE('',#20861,#19219,#12650,.T.); -#36193=ADVANCED_FACE('',(#36192),#36185,.F.); -#36200=EDGE_CURVE('',#20859,#19217,#12654,.T.); -#36206=ADVANCED_FACE('',(#36205),#36198,.F.); -#36213=EDGE_CURVE('',#20857,#19215,#12658,.T.); -#36219=ADVANCED_FACE('',(#36218),#36211,.F.); -#36226=EDGE_CURVE('',#20855,#19213,#12662,.T.); -#36232=ADVANCED_FACE('',(#36231),#36224,.F.); -#36239=EDGE_CURVE('',#20853,#19211,#12666,.T.); -#36245=ADVANCED_FACE('',(#36244),#36237,.F.); -#36252=EDGE_CURVE('',#20851,#19209,#12670,.T.); -#36258=ADVANCED_FACE('',(#36257),#36250,.F.); -#36265=EDGE_CURVE('',#20849,#19207,#12674,.T.); -#36271=ADVANCED_FACE('',(#36270),#36263,.F.); -#36278=EDGE_CURVE('',#20847,#19205,#12678,.T.); -#36284=ADVANCED_FACE('',(#36283),#36276,.F.); -#36291=EDGE_CURVE('',#20845,#19203,#12682,.T.); -#36297=ADVANCED_FACE('',(#36296),#36289,.F.); -#36304=EDGE_CURVE('',#20843,#19201,#12686,.T.); -#36310=ADVANCED_FACE('',(#36309),#36302,.F.); -#36317=EDGE_CURVE('',#20841,#19199,#12690,.T.); -#36323=ADVANCED_FACE('',(#36322),#36315,.F.); -#36330=EDGE_CURVE('',#20839,#19197,#12694,.T.); -#36336=ADVANCED_FACE('',(#36335),#36328,.F.); -#36343=EDGE_CURVE('',#20837,#19195,#12698,.T.); -#36349=ADVANCED_FACE('',(#36348),#36341,.F.); -#36356=EDGE_CURVE('',#20835,#19193,#12702,.T.); -#36362=ADVANCED_FACE('',(#36361),#36354,.F.); -#36369=EDGE_CURVE('',#20833,#19191,#12706,.T.); -#36375=ADVANCED_FACE('',(#36374),#36367,.F.); -#36382=EDGE_CURVE('',#20831,#19189,#12710,.T.); -#36388=ADVANCED_FACE('',(#36387),#36380,.F.); -#36395=EDGE_CURVE('',#20829,#19187,#12714,.T.); -#36401=ADVANCED_FACE('',(#36400),#36393,.F.); -#36408=EDGE_CURVE('',#20827,#19185,#12718,.T.); -#36414=ADVANCED_FACE('',(#36413),#36406,.F.); -#36421=EDGE_CURVE('',#20825,#19183,#12722,.T.); -#36427=ADVANCED_FACE('',(#36426),#36419,.F.); -#36434=EDGE_CURVE('',#20823,#19181,#12726,.T.); -#36440=ADVANCED_FACE('',(#36439),#36432,.F.); -#36447=EDGE_CURVE('',#20821,#19179,#12730,.T.); -#36453=ADVANCED_FACE('',(#36452),#36445,.F.); -#36460=EDGE_CURVE('',#20819,#19177,#12734,.T.); -#36466=ADVANCED_FACE('',(#36465),#36458,.F.); -#36478=ADVANCED_FACE('',(#36477),#36471,.F.); -#36485=EDGE_CURVE('',#20884,#19242,#12742,.T.); -#36488=EDGE_CURVE('',#20885,#19243,#12802,.T.); -#36492=ADVANCED_FACE('',(#36491),#36483,.F.); -#36499=EDGE_CURVE('',#20913,#19271,#12746,.T.); -#36505=ADVANCED_FACE('',(#36504),#36497,.F.); -#36512=EDGE_CURVE('',#20911,#19269,#12750,.T.); -#36518=ADVANCED_FACE('',(#36517),#36510,.F.); -#36525=EDGE_CURVE('',#20909,#19267,#12754,.T.); -#36531=ADVANCED_FACE('',(#36530),#36523,.F.); -#36538=EDGE_CURVE('',#20907,#19265,#12758,.T.); -#36544=ADVANCED_FACE('',(#36543),#36536,.F.); -#36551=EDGE_CURVE('',#20905,#19263,#12762,.T.); -#36557=ADVANCED_FACE('',(#36556),#36549,.F.); -#36564=EDGE_CURVE('',#20903,#19261,#12766,.T.); -#36570=ADVANCED_FACE('',(#36569),#36562,.F.); -#36577=EDGE_CURVE('',#20901,#19259,#12770,.T.); -#36583=ADVANCED_FACE('',(#36582),#36575,.F.); -#36590=EDGE_CURVE('',#20899,#19257,#12774,.T.); -#36596=ADVANCED_FACE('',(#36595),#36588,.F.); -#36603=EDGE_CURVE('',#20897,#19255,#12778,.T.); -#36609=ADVANCED_FACE('',(#36608),#36601,.F.); -#36616=EDGE_CURVE('',#20895,#19253,#12782,.T.); -#36622=ADVANCED_FACE('',(#36621),#36614,.F.); -#36629=EDGE_CURVE('',#20893,#19251,#12786,.T.); -#36635=ADVANCED_FACE('',(#36634),#36627,.F.); -#36642=EDGE_CURVE('',#20891,#19249,#12790,.T.); -#36648=ADVANCED_FACE('',(#36647),#36640,.F.); -#36655=EDGE_CURVE('',#20889,#19247,#12794,.T.); -#36661=ADVANCED_FACE('',(#36660),#36653,.F.); -#36668=EDGE_CURVE('',#20887,#19245,#12798,.T.); -#36674=ADVANCED_FACE('',(#36673),#36666,.F.); -#36686=ADVANCED_FACE('',(#36685),#36679,.F.); -#36693=EDGE_CURVE('',#20916,#19274,#12806,.T.); -#36696=EDGE_CURVE('',#20917,#19275,#12866,.T.); -#36700=ADVANCED_FACE('',(#36699),#36691,.F.); -#36707=EDGE_CURVE('',#20945,#19303,#12810,.T.); -#36713=ADVANCED_FACE('',(#36712),#36705,.F.); -#36720=EDGE_CURVE('',#20943,#19301,#12814,.T.); -#36726=ADVANCED_FACE('',(#36725),#36718,.F.); -#36733=EDGE_CURVE('',#20941,#19299,#12818,.T.); -#36739=ADVANCED_FACE('',(#36738),#36731,.F.); -#36746=EDGE_CURVE('',#20939,#19297,#12822,.T.); -#36752=ADVANCED_FACE('',(#36751),#36744,.F.); -#36759=EDGE_CURVE('',#20937,#19295,#12826,.T.); -#36765=ADVANCED_FACE('',(#36764),#36757,.F.); -#36772=EDGE_CURVE('',#20935,#19293,#12830,.T.); -#36778=ADVANCED_FACE('',(#36777),#36770,.F.); -#36785=EDGE_CURVE('',#20933,#19291,#12834,.T.); -#36791=ADVANCED_FACE('',(#36790),#36783,.F.); -#36798=EDGE_CURVE('',#20931,#19289,#12838,.T.); -#36804=ADVANCED_FACE('',(#36803),#36796,.F.); -#36811=EDGE_CURVE('',#20929,#19287,#12842,.T.); -#36817=ADVANCED_FACE('',(#36816),#36809,.F.); -#36824=EDGE_CURVE('',#20927,#19285,#12846,.T.); -#36830=ADVANCED_FACE('',(#36829),#36822,.F.); -#36837=EDGE_CURVE('',#20925,#19283,#12850,.T.); -#36843=ADVANCED_FACE('',(#36842),#36835,.F.); -#36850=EDGE_CURVE('',#20923,#19281,#12854,.T.); -#36856=ADVANCED_FACE('',(#36855),#36848,.F.); -#36863=EDGE_CURVE('',#20921,#19279,#12858,.T.); -#36869=ADVANCED_FACE('',(#36868),#36861,.F.); -#36876=EDGE_CURVE('',#20919,#19277,#12862,.T.); -#36882=ADVANCED_FACE('',(#36881),#36874,.F.); -#36894=ADVANCED_FACE('',(#36893),#36887,.F.); -#36901=EDGE_CURVE('',#20948,#19306,#12870,.T.); -#36904=EDGE_CURVE('',#20949,#19307,#13094,.T.); -#36908=ADVANCED_FACE('',(#36907),#36899,.F.); -#36915=EDGE_CURVE('',#21059,#19417,#12874,.T.); -#36921=ADVANCED_FACE('',(#36920),#36913,.F.); -#36928=EDGE_CURVE('',#21057,#19415,#12878,.T.); -#36934=ADVANCED_FACE('',(#36933),#36926,.F.); -#36941=EDGE_CURVE('',#21055,#19413,#12882,.T.); -#36947=ADVANCED_FACE('',(#36946),#36939,.F.); -#36954=EDGE_CURVE('',#21053,#19411,#12886,.T.); -#36960=ADVANCED_FACE('',(#36959),#36952,.F.); -#36967=EDGE_CURVE('',#21051,#19409,#12890,.T.); -#36973=ADVANCED_FACE('',(#36972),#36965,.F.); -#36980=EDGE_CURVE('',#21049,#19407,#12894,.T.); -#36986=ADVANCED_FACE('',(#36985),#36978,.F.); -#36993=EDGE_CURVE('',#21047,#19405,#12898,.T.); -#36999=ADVANCED_FACE('',(#36998),#36991,.F.); -#37006=EDGE_CURVE('',#21045,#19403,#12902,.T.); -#37012=ADVANCED_FACE('',(#37011),#37004,.F.); -#37019=EDGE_CURVE('',#21043,#19401,#12906,.T.); -#37025=ADVANCED_FACE('',(#37024),#37017,.F.); -#37032=EDGE_CURVE('',#21041,#19399,#12910,.T.); -#37038=ADVANCED_FACE('',(#37037),#37030,.F.); -#37045=EDGE_CURVE('',#21039,#19397,#12914,.T.); -#37051=ADVANCED_FACE('',(#37050),#37043,.F.); -#37058=EDGE_CURVE('',#21037,#19395,#12918,.T.); -#37064=ADVANCED_FACE('',(#37063),#37056,.F.); -#37071=EDGE_CURVE('',#21035,#19393,#12922,.T.); -#37077=ADVANCED_FACE('',(#37076),#37069,.F.); -#37084=EDGE_CURVE('',#21033,#19391,#12926,.T.); -#37090=ADVANCED_FACE('',(#37089),#37082,.F.); -#37097=EDGE_CURVE('',#21031,#19389,#12930,.T.); -#37103=ADVANCED_FACE('',(#37102),#37095,.F.); -#37110=EDGE_CURVE('',#21029,#19387,#12934,.T.); -#37116=ADVANCED_FACE('',(#37115),#37108,.F.); -#37123=EDGE_CURVE('',#21027,#19385,#12938,.T.); -#37129=ADVANCED_FACE('',(#37128),#37121,.F.); -#37136=EDGE_CURVE('',#21025,#19383,#12942,.T.); -#37142=ADVANCED_FACE('',(#37141),#37134,.F.); -#37149=EDGE_CURVE('',#21023,#19381,#12946,.T.); -#37155=ADVANCED_FACE('',(#37154),#37147,.F.); -#37162=EDGE_CURVE('',#21021,#19379,#12950,.T.); -#37168=ADVANCED_FACE('',(#37167),#37160,.F.); -#37175=EDGE_CURVE('',#21019,#19377,#12954,.T.); -#37181=ADVANCED_FACE('',(#37180),#37173,.F.); -#37188=EDGE_CURVE('',#21017,#19375,#12958,.T.); -#37194=ADVANCED_FACE('',(#37193),#37186,.F.); -#37201=EDGE_CURVE('',#21015,#19373,#12962,.T.); -#37207=ADVANCED_FACE('',(#37206),#37199,.F.); -#37214=EDGE_CURVE('',#21013,#19371,#12966,.T.); -#37220=ADVANCED_FACE('',(#37219),#37212,.F.); -#37227=EDGE_CURVE('',#21011,#19369,#12970,.T.); -#37233=ADVANCED_FACE('',(#37232),#37225,.F.); -#37240=EDGE_CURVE('',#21009,#19367,#12974,.T.); -#37246=ADVANCED_FACE('',(#37245),#37238,.F.); -#37253=EDGE_CURVE('',#21007,#19365,#12978,.T.); -#37259=ADVANCED_FACE('',(#37258),#37251,.F.); -#37266=EDGE_CURVE('',#21005,#19363,#12982,.T.); -#37272=ADVANCED_FACE('',(#37271),#37264,.F.); -#37279=EDGE_CURVE('',#21003,#19361,#12986,.T.); -#37285=ADVANCED_FACE('',(#37284),#37277,.F.); -#37292=EDGE_CURVE('',#21001,#19359,#12990,.T.); -#37298=ADVANCED_FACE('',(#37297),#37290,.F.); -#37305=EDGE_CURVE('',#20999,#19357,#12994,.T.); -#37311=ADVANCED_FACE('',(#37310),#37303,.F.); -#37318=EDGE_CURVE('',#20997,#19355,#12998,.T.); -#37324=ADVANCED_FACE('',(#37323),#37316,.F.); -#37331=EDGE_CURVE('',#20995,#19353,#13002,.T.); -#37337=ADVANCED_FACE('',(#37336),#37329,.F.); -#37344=EDGE_CURVE('',#20993,#19351,#13006,.T.); -#37350=ADVANCED_FACE('',(#37349),#37342,.F.); -#37357=EDGE_CURVE('',#20991,#19349,#13010,.T.); -#37363=ADVANCED_FACE('',(#37362),#37355,.F.); -#37370=EDGE_CURVE('',#20989,#19347,#13014,.T.); -#37376=ADVANCED_FACE('',(#37375),#37368,.F.); -#37383=EDGE_CURVE('',#20987,#19345,#13018,.T.); -#37389=ADVANCED_FACE('',(#37388),#37381,.F.); -#37396=EDGE_CURVE('',#20985,#19343,#13022,.T.); -#37402=ADVANCED_FACE('',(#37401),#37394,.F.); -#37409=EDGE_CURVE('',#20983,#19341,#13026,.T.); -#37415=ADVANCED_FACE('',(#37414),#37407,.F.); -#37422=EDGE_CURVE('',#20981,#19339,#13030,.T.); -#37428=ADVANCED_FACE('',(#37427),#37420,.F.); -#37435=EDGE_CURVE('',#20979,#19337,#13034,.T.); -#37441=ADVANCED_FACE('',(#37440),#37433,.F.); -#37448=EDGE_CURVE('',#20977,#19335,#13038,.T.); -#37454=ADVANCED_FACE('',(#37453),#37446,.F.); -#37461=EDGE_CURVE('',#20975,#19333,#13042,.T.); -#37467=ADVANCED_FACE('',(#37466),#37459,.F.); -#37474=EDGE_CURVE('',#20973,#19331,#13046,.T.); -#37480=ADVANCED_FACE('',(#37479),#37472,.F.); -#37487=EDGE_CURVE('',#20971,#19329,#13050,.T.); -#37493=ADVANCED_FACE('',(#37492),#37485,.F.); -#37500=EDGE_CURVE('',#20969,#19327,#13054,.T.); -#37506=ADVANCED_FACE('',(#37505),#37498,.F.); -#37513=EDGE_CURVE('',#20967,#19325,#13058,.T.); -#37519=ADVANCED_FACE('',(#37518),#37511,.F.); -#37526=EDGE_CURVE('',#20965,#19323,#13062,.T.); -#37532=ADVANCED_FACE('',(#37531),#37524,.F.); -#37539=EDGE_CURVE('',#20963,#19321,#13066,.T.); -#37545=ADVANCED_FACE('',(#37544),#37537,.F.); -#37552=EDGE_CURVE('',#20961,#19319,#13070,.T.); -#37558=ADVANCED_FACE('',(#37557),#37550,.F.); -#37565=EDGE_CURVE('',#20959,#19317,#13074,.T.); -#37571=ADVANCED_FACE('',(#37570),#37563,.F.); -#37578=EDGE_CURVE('',#20957,#19315,#13078,.T.); -#37584=ADVANCED_FACE('',(#37583),#37576,.F.); -#37591=EDGE_CURVE('',#20955,#19313,#13082,.T.); -#37597=ADVANCED_FACE('',(#37596),#37589,.F.); -#37604=EDGE_CURVE('',#20953,#19311,#13086,.T.); -#37610=ADVANCED_FACE('',(#37609),#37602,.F.); -#37617=EDGE_CURVE('',#20951,#19309,#13090,.T.); -#37623=ADVANCED_FACE('',(#37622),#37615,.F.); -#37635=ADVANCED_FACE('',(#37634),#37628,.F.); -#37642=EDGE_CURVE('',#21062,#19420,#13098,.T.); -#37645=EDGE_CURVE('',#21063,#19421,#13206,.T.); -#37649=ADVANCED_FACE('',(#37648),#37640,.F.); -#37656=EDGE_CURVE('',#21115,#19473,#13102,.T.); -#37662=ADVANCED_FACE('',(#37661),#37654,.F.); -#37669=EDGE_CURVE('',#21113,#19471,#13106,.T.); -#37675=ADVANCED_FACE('',(#37674),#37667,.F.); -#37682=EDGE_CURVE('',#21111,#19469,#13110,.T.); -#37688=ADVANCED_FACE('',(#37687),#37680,.F.); -#37695=EDGE_CURVE('',#21109,#19467,#13114,.T.); -#37701=ADVANCED_FACE('',(#37700),#37693,.F.); -#37708=EDGE_CURVE('',#21107,#19465,#13118,.T.); -#37714=ADVANCED_FACE('',(#37713),#37706,.F.); -#37721=EDGE_CURVE('',#21105,#19463,#13122,.T.); -#37727=ADVANCED_FACE('',(#37726),#37719,.F.); -#37734=EDGE_CURVE('',#21103,#19461,#13126,.T.); -#37740=ADVANCED_FACE('',(#37739),#37732,.F.); -#37747=EDGE_CURVE('',#21101,#19459,#13130,.T.); -#37753=ADVANCED_FACE('',(#37752),#37745,.F.); -#37760=EDGE_CURVE('',#21099,#19457,#13134,.T.); -#37766=ADVANCED_FACE('',(#37765),#37758,.F.); -#37773=EDGE_CURVE('',#21097,#19455,#13138,.T.); -#37779=ADVANCED_FACE('',(#37778),#37771,.F.); -#37786=EDGE_CURVE('',#21095,#19453,#13142,.T.); -#37792=ADVANCED_FACE('',(#37791),#37784,.F.); -#37799=EDGE_CURVE('',#21093,#19451,#13146,.T.); -#37805=ADVANCED_FACE('',(#37804),#37797,.F.); -#37812=EDGE_CURVE('',#21091,#19449,#13150,.T.); -#37818=ADVANCED_FACE('',(#37817),#37810,.F.); -#37825=EDGE_CURVE('',#21089,#19447,#13154,.T.); -#37831=ADVANCED_FACE('',(#37830),#37823,.F.); -#37838=EDGE_CURVE('',#21087,#19445,#13158,.T.); -#37844=ADVANCED_FACE('',(#37843),#37836,.F.); -#37851=EDGE_CURVE('',#21085,#19443,#13162,.T.); -#37857=ADVANCED_FACE('',(#37856),#37849,.F.); -#37864=EDGE_CURVE('',#21083,#19441,#13166,.T.); -#37870=ADVANCED_FACE('',(#37869),#37862,.F.); -#37877=EDGE_CURVE('',#21081,#19439,#13170,.T.); -#37883=ADVANCED_FACE('',(#37882),#37875,.F.); -#37890=EDGE_CURVE('',#21079,#19437,#13174,.T.); -#37896=ADVANCED_FACE('',(#37895),#37888,.F.); -#37903=EDGE_CURVE('',#21077,#19435,#13178,.T.); -#37909=ADVANCED_FACE('',(#37908),#37901,.F.); -#37916=EDGE_CURVE('',#21075,#19433,#13182,.T.); -#37922=ADVANCED_FACE('',(#37921),#37914,.F.); -#37929=EDGE_CURVE('',#21073,#19431,#13186,.T.); -#37935=ADVANCED_FACE('',(#37934),#37927,.F.); -#37942=EDGE_CURVE('',#21071,#19429,#13190,.T.); -#37948=ADVANCED_FACE('',(#37947),#37940,.F.); -#37955=EDGE_CURVE('',#21069,#19427,#13194,.T.); -#37961=ADVANCED_FACE('',(#37960),#37953,.F.); -#37968=EDGE_CURVE('',#21067,#19425,#13198,.T.); -#37974=ADVANCED_FACE('',(#37973),#37966,.F.); -#37981=EDGE_CURVE('',#21065,#19423,#13202,.T.); -#37987=ADVANCED_FACE('',(#37986),#37979,.F.); -#37999=ADVANCED_FACE('',(#37998),#37992,.F.); -#38006=EDGE_CURVE('',#21118,#19476,#13210,.T.); -#38009=EDGE_CURVE('',#21119,#19477,#13222,.T.); -#38013=ADVANCED_FACE('',(#38012),#38004,.F.); -#38020=EDGE_CURVE('',#21123,#19481,#13214,.T.); -#38026=ADVANCED_FACE('',(#38025),#38018,.F.); -#38033=EDGE_CURVE('',#21121,#19479,#13218,.T.); -#38039=ADVANCED_FACE('',(#38038),#38031,.F.); -#38051=ADVANCED_FACE('',(#38050),#38044,.F.); -#38058=EDGE_CURVE('',#21126,#19484,#13226,.T.); -#38061=EDGE_CURVE('',#21127,#19485,#13382,.T.); -#38065=ADVANCED_FACE('',(#38064),#38056,.F.); -#38072=EDGE_CURVE('',#21203,#19561,#13230,.T.); -#38078=ADVANCED_FACE('',(#38077),#38070,.F.); -#38085=EDGE_CURVE('',#21201,#19559,#13234,.T.); -#38091=ADVANCED_FACE('',(#38090),#38083,.F.); -#38098=EDGE_CURVE('',#21199,#19557,#13238,.T.); -#38104=ADVANCED_FACE('',(#38103),#38096,.F.); -#38111=EDGE_CURVE('',#21197,#19555,#13242,.T.); -#38117=ADVANCED_FACE('',(#38116),#38109,.F.); -#38124=EDGE_CURVE('',#21195,#19553,#13246,.T.); -#38130=ADVANCED_FACE('',(#38129),#38122,.F.); -#38137=EDGE_CURVE('',#21193,#19551,#13250,.T.); -#38143=ADVANCED_FACE('',(#38142),#38135,.F.); -#38150=EDGE_CURVE('',#21191,#19549,#13254,.T.); -#38156=ADVANCED_FACE('',(#38155),#38148,.F.); -#38163=EDGE_CURVE('',#21189,#19547,#13258,.T.); -#38169=ADVANCED_FACE('',(#38168),#38161,.F.); -#38176=EDGE_CURVE('',#21187,#19545,#13262,.T.); -#38182=ADVANCED_FACE('',(#38181),#38174,.F.); -#38189=EDGE_CURVE('',#21185,#19543,#13266,.T.); -#38195=ADVANCED_FACE('',(#38194),#38187,.F.); -#38202=EDGE_CURVE('',#21183,#19541,#13270,.T.); -#38208=ADVANCED_FACE('',(#38207),#38200,.F.); -#38215=EDGE_CURVE('',#21181,#19539,#13274,.T.); -#38221=ADVANCED_FACE('',(#38220),#38213,.F.); -#38228=EDGE_CURVE('',#21179,#19537,#13278,.T.); -#38234=ADVANCED_FACE('',(#38233),#38226,.F.); -#38241=EDGE_CURVE('',#21177,#19535,#13282,.T.); -#38247=ADVANCED_FACE('',(#38246),#38239,.F.); -#38254=EDGE_CURVE('',#21175,#19533,#13286,.T.); -#38260=ADVANCED_FACE('',(#38259),#38252,.F.); -#38267=EDGE_CURVE('',#21173,#19531,#13290,.T.); -#38273=ADVANCED_FACE('',(#38272),#38265,.F.); -#38280=EDGE_CURVE('',#21171,#19529,#13294,.T.); -#38286=ADVANCED_FACE('',(#38285),#38278,.F.); -#38293=EDGE_CURVE('',#21169,#19527,#13298,.T.); -#38299=ADVANCED_FACE('',(#38298),#38291,.F.); -#38306=EDGE_CURVE('',#21167,#19525,#13302,.T.); -#38312=ADVANCED_FACE('',(#38311),#38304,.F.); -#38319=EDGE_CURVE('',#21165,#19523,#13306,.T.); -#38325=ADVANCED_FACE('',(#38324),#38317,.F.); -#38332=EDGE_CURVE('',#21163,#19521,#13310,.T.); -#38338=ADVANCED_FACE('',(#38337),#38330,.F.); -#38345=EDGE_CURVE('',#21161,#19519,#13314,.T.); -#38351=ADVANCED_FACE('',(#38350),#38343,.F.); -#38358=EDGE_CURVE('',#21159,#19517,#13318,.T.); -#38364=ADVANCED_FACE('',(#38363),#38356,.F.); -#38371=EDGE_CURVE('',#21157,#19515,#13322,.T.); -#38377=ADVANCED_FACE('',(#38376),#38369,.F.); -#38384=EDGE_CURVE('',#21155,#19513,#13326,.T.); -#38390=ADVANCED_FACE('',(#38389),#38382,.F.); -#38397=EDGE_CURVE('',#21153,#19511,#13330,.T.); -#38403=ADVANCED_FACE('',(#38402),#38395,.F.); -#38410=EDGE_CURVE('',#21151,#19509,#13334,.T.); -#38416=ADVANCED_FACE('',(#38415),#38408,.F.); -#38423=EDGE_CURVE('',#21149,#19507,#13338,.T.); -#38429=ADVANCED_FACE('',(#38428),#38421,.F.); -#38436=EDGE_CURVE('',#21147,#19505,#13342,.T.); -#38442=ADVANCED_FACE('',(#38441),#38434,.F.); -#38449=EDGE_CURVE('',#21145,#19503,#13346,.T.); -#38455=ADVANCED_FACE('',(#38454),#38447,.F.); -#38462=EDGE_CURVE('',#21143,#19501,#13350,.T.); -#38468=ADVANCED_FACE('',(#38467),#38460,.F.); -#38475=EDGE_CURVE('',#21141,#19499,#13354,.T.); -#38481=ADVANCED_FACE('',(#38480),#38473,.F.); -#38488=EDGE_CURVE('',#21139,#19497,#13358,.T.); -#38494=ADVANCED_FACE('',(#38493),#38486,.F.); -#38501=EDGE_CURVE('',#21137,#19495,#13362,.T.); -#38507=ADVANCED_FACE('',(#38506),#38499,.F.); -#38514=EDGE_CURVE('',#21135,#19493,#13366,.T.); -#38520=ADVANCED_FACE('',(#38519),#38512,.F.); -#38527=EDGE_CURVE('',#21133,#19491,#13370,.T.); -#38533=ADVANCED_FACE('',(#38532),#38525,.F.); -#38540=EDGE_CURVE('',#21131,#19489,#13374,.T.); -#38546=ADVANCED_FACE('',(#38545),#38538,.F.); -#38553=EDGE_CURVE('',#21129,#19487,#13378,.T.); -#38559=ADVANCED_FACE('',(#38558),#38551,.F.); -#38571=ADVANCED_FACE('',(#38570),#38564,.F.); -#38578=EDGE_CURVE('',#21206,#19564,#13386,.T.); -#38581=EDGE_CURVE('',#21207,#19565,#13398,.T.); -#38585=ADVANCED_FACE('',(#38584),#38576,.F.); -#38592=EDGE_CURVE('',#21211,#19569,#13390,.T.); -#38598=ADVANCED_FACE('',(#38597),#38590,.F.); -#38605=EDGE_CURVE('',#21209,#19567,#13394,.T.); -#38611=ADVANCED_FACE('',(#38610),#38603,.F.); -#38623=ADVANCED_FACE('',(#38622),#38616,.F.); -#38630=EDGE_CURVE('',#21214,#19572,#13402,.T.); -#38633=EDGE_CURVE('',#21215,#19573,#13454,.T.); -#38637=ADVANCED_FACE('',(#38636),#38628,.F.); -#38644=EDGE_CURVE('',#21239,#19597,#13406,.T.); -#38650=ADVANCED_FACE('',(#38649),#38642,.F.); -#38657=EDGE_CURVE('',#21237,#19595,#13410,.T.); -#38663=ADVANCED_FACE('',(#38662),#38655,.F.); -#38670=EDGE_CURVE('',#21235,#19593,#13414,.T.); -#38676=ADVANCED_FACE('',(#38675),#38668,.F.); -#38683=EDGE_CURVE('',#21233,#19591,#13418,.T.); -#38689=ADVANCED_FACE('',(#38688),#38681,.F.); -#38696=EDGE_CURVE('',#21231,#19589,#13422,.T.); -#38702=ADVANCED_FACE('',(#38701),#38694,.F.); -#38709=EDGE_CURVE('',#21229,#19587,#13426,.T.); -#38715=ADVANCED_FACE('',(#38714),#38707,.F.); -#38722=EDGE_CURVE('',#21227,#19585,#13430,.T.); -#38728=ADVANCED_FACE('',(#38727),#38720,.F.); -#38735=EDGE_CURVE('',#21225,#19583,#13434,.T.); -#38741=ADVANCED_FACE('',(#38740),#38733,.F.); -#38748=EDGE_CURVE('',#21223,#19581,#13438,.T.); -#38754=ADVANCED_FACE('',(#38753),#38746,.F.); -#38761=EDGE_CURVE('',#21221,#19579,#13442,.T.); -#38767=ADVANCED_FACE('',(#38766),#38759,.F.); -#38774=EDGE_CURVE('',#21219,#19577,#13446,.T.); -#38780=ADVANCED_FACE('',(#38779),#38772,.F.); -#38787=EDGE_CURVE('',#21217,#19575,#13450,.T.); -#38793=ADVANCED_FACE('',(#38792),#38785,.F.); -#38805=ADVANCED_FACE('',(#38804),#38798,.F.); -#38812=EDGE_CURVE('',#21242,#19600,#13458,.T.); -#38815=EDGE_CURVE('',#21243,#19601,#13502,.T.); -#38819=ADVANCED_FACE('',(#38818),#38810,.F.); -#38826=EDGE_CURVE('',#21263,#19621,#13462,.T.); -#38832=ADVANCED_FACE('',(#38831),#38824,.F.); -#38839=EDGE_CURVE('',#21261,#19619,#13466,.T.); -#38845=ADVANCED_FACE('',(#38844),#38837,.F.); -#38852=EDGE_CURVE('',#21259,#19617,#13470,.T.); -#38858=ADVANCED_FACE('',(#38857),#38850,.F.); -#38865=EDGE_CURVE('',#21257,#19615,#13474,.T.); -#38871=ADVANCED_FACE('',(#38870),#38863,.F.); -#38878=EDGE_CURVE('',#21255,#19613,#13478,.T.); -#38884=ADVANCED_FACE('',(#38883),#38876,.F.); -#38891=EDGE_CURVE('',#21253,#19611,#13482,.T.); -#38897=ADVANCED_FACE('',(#38896),#38889,.F.); -#38904=EDGE_CURVE('',#21251,#19609,#13486,.T.); -#38910=ADVANCED_FACE('',(#38909),#38902,.F.); -#38917=EDGE_CURVE('',#21249,#19607,#13490,.T.); -#38923=ADVANCED_FACE('',(#38922),#38915,.F.); -#38930=EDGE_CURVE('',#21247,#19605,#13494,.T.); -#38936=ADVANCED_FACE('',(#38935),#38928,.F.); -#38943=EDGE_CURVE('',#21245,#19603,#13498,.T.); -#38949=ADVANCED_FACE('',(#38948),#38941,.F.); -#38961=ADVANCED_FACE('',(#38960),#38954,.F.); -#38968=EDGE_CURVE('',#21266,#19624,#13506,.T.); -#38971=EDGE_CURVE('',#21267,#19625,#13518,.T.); -#38975=ADVANCED_FACE('',(#38974),#38966,.F.); -#38982=EDGE_CURVE('',#21271,#19629,#13510,.T.); -#38988=ADVANCED_FACE('',(#38987),#38980,.F.); -#38995=EDGE_CURVE('',#21269,#19627,#13514,.T.); -#39001=ADVANCED_FACE('',(#39000),#38993,.F.); -#39013=ADVANCED_FACE('',(#39012),#39006,.F.); -#39020=EDGE_CURVE('',#21274,#19632,#13522,.T.); -#39023=EDGE_CURVE('',#21275,#19633,#13534,.T.); -#39027=ADVANCED_FACE('',(#39026),#39018,.F.); -#39034=EDGE_CURVE('',#21279,#19637,#13526,.T.); -#39040=ADVANCED_FACE('',(#39039),#39032,.F.); -#39047=EDGE_CURVE('',#21277,#19635,#13530,.T.); -#39053=ADVANCED_FACE('',(#39052),#39045,.F.); -#39065=ADVANCED_FACE('',(#39064),#39058,.F.); -#39072=EDGE_CURVE('',#21282,#19640,#13538,.T.); -#39075=EDGE_CURVE('',#21283,#19641,#13578,.T.); -#39079=ADVANCED_FACE('',(#39078),#39070,.F.); -#39086=EDGE_CURVE('',#21301,#19659,#13542,.T.); -#39092=ADVANCED_FACE('',(#39091),#39084,.F.); -#39099=EDGE_CURVE('',#21299,#19657,#13546,.T.); -#39105=ADVANCED_FACE('',(#39104),#39097,.F.); -#39112=EDGE_CURVE('',#21297,#19655,#13550,.T.); -#39118=ADVANCED_FACE('',(#39117),#39110,.F.); -#39125=EDGE_CURVE('',#21295,#19653,#13554,.T.); -#39131=ADVANCED_FACE('',(#39130),#39123,.F.); -#39138=EDGE_CURVE('',#21293,#19651,#13558,.T.); -#39144=ADVANCED_FACE('',(#39143),#39136,.F.); -#39151=EDGE_CURVE('',#21291,#19649,#13562,.T.); -#39157=ADVANCED_FACE('',(#39156),#39149,.F.); -#39164=EDGE_CURVE('',#21289,#19647,#13566,.T.); -#39170=ADVANCED_FACE('',(#39169),#39162,.F.); -#39177=EDGE_CURVE('',#21287,#19645,#13570,.T.); -#39183=ADVANCED_FACE('',(#39182),#39175,.F.); -#39190=EDGE_CURVE('',#21285,#19643,#13574,.T.); -#39196=ADVANCED_FACE('',(#39195),#39188,.F.); -#39208=ADVANCED_FACE('',(#39207),#39201,.F.); -#39215=EDGE_CURVE('',#21304,#19662,#13582,.T.); -#39218=EDGE_CURVE('',#21305,#19663,#13590,.T.); -#39222=ADVANCED_FACE('',(#39221),#39213,.F.); -#39229=EDGE_CURVE('',#21307,#19665,#13586,.T.); -#39235=ADVANCED_FACE('',(#39234),#39227,.F.); -#39247=ADVANCED_FACE('',(#39246),#39240,.F.); -#39254=EDGE_CURVE('',#21310,#19668,#13594,.T.); -#39257=EDGE_CURVE('',#21311,#19669,#13618,.T.); -#39261=ADVANCED_FACE('',(#39260),#39252,.F.); -#39268=EDGE_CURVE('',#21321,#19679,#13598,.T.); -#39274=ADVANCED_FACE('',(#39273),#39266,.F.); -#39281=EDGE_CURVE('',#21319,#19677,#13602,.T.); -#39287=ADVANCED_FACE('',(#39286),#39279,.F.); -#39294=EDGE_CURVE('',#21317,#19675,#13606,.T.); -#39300=ADVANCED_FACE('',(#39299),#39292,.F.); -#39307=EDGE_CURVE('',#21315,#19673,#13610,.T.); -#39313=ADVANCED_FACE('',(#39312),#39305,.F.); -#39320=EDGE_CURVE('',#21313,#19671,#13614,.T.); -#39326=ADVANCED_FACE('',(#39325),#39318,.F.); -#39338=ADVANCED_FACE('',(#39337),#39331,.F.); -#39345=EDGE_CURVE('',#21324,#19682,#13622,.T.); -#39348=EDGE_CURVE('',#21325,#19683,#13722,.T.); -#39352=ADVANCED_FACE('',(#39351),#39343,.F.); -#39359=EDGE_CURVE('',#21373,#19731,#13626,.T.); -#39365=ADVANCED_FACE('',(#39364),#39357,.F.); -#39372=EDGE_CURVE('',#21371,#19729,#13630,.T.); -#39378=ADVANCED_FACE('',(#39377),#39370,.F.); -#39385=EDGE_CURVE('',#21369,#19727,#13634,.T.); -#39391=ADVANCED_FACE('',(#39390),#39383,.F.); -#39398=EDGE_CURVE('',#21367,#19725,#13638,.T.); -#39404=ADVANCED_FACE('',(#39403),#39396,.F.); -#39411=EDGE_CURVE('',#21365,#19723,#13642,.T.); -#39417=ADVANCED_FACE('',(#39416),#39409,.F.); -#39424=EDGE_CURVE('',#21363,#19721,#13646,.T.); -#39430=ADVANCED_FACE('',(#39429),#39422,.F.); -#39437=EDGE_CURVE('',#21361,#19719,#13650,.T.); -#39443=ADVANCED_FACE('',(#39442),#39435,.F.); -#39450=EDGE_CURVE('',#21359,#19717,#13654,.T.); -#39456=ADVANCED_FACE('',(#39455),#39448,.F.); -#39463=EDGE_CURVE('',#21357,#19715,#13658,.T.); -#39469=ADVANCED_FACE('',(#39468),#39461,.F.); -#39476=EDGE_CURVE('',#21355,#19713,#13662,.T.); -#39482=ADVANCED_FACE('',(#39481),#39474,.F.); -#39489=EDGE_CURVE('',#21353,#19711,#13666,.T.); -#39495=ADVANCED_FACE('',(#39494),#39487,.F.); -#39502=EDGE_CURVE('',#21351,#19709,#13670,.T.); -#39508=ADVANCED_FACE('',(#39507),#39500,.F.); -#39515=EDGE_CURVE('',#21349,#19707,#13674,.T.); -#39521=ADVANCED_FACE('',(#39520),#39513,.F.); -#39528=EDGE_CURVE('',#21347,#19705,#13678,.T.); -#39534=ADVANCED_FACE('',(#39533),#39526,.F.); -#39541=EDGE_CURVE('',#21345,#19703,#13682,.T.); -#39547=ADVANCED_FACE('',(#39546),#39539,.F.); -#39554=EDGE_CURVE('',#21343,#19701,#13686,.T.); -#39560=ADVANCED_FACE('',(#39559),#39552,.F.); -#39567=EDGE_CURVE('',#21341,#19699,#13690,.T.); -#39573=ADVANCED_FACE('',(#39572),#39565,.F.); -#39580=EDGE_CURVE('',#21339,#19697,#13694,.T.); -#39586=ADVANCED_FACE('',(#39585),#39578,.F.); -#39593=EDGE_CURVE('',#21337,#19695,#13698,.T.); -#39599=ADVANCED_FACE('',(#39598),#39591,.F.); -#39606=EDGE_CURVE('',#21335,#19693,#13702,.T.); -#39612=ADVANCED_FACE('',(#39611),#39604,.F.); -#39619=EDGE_CURVE('',#21333,#19691,#13706,.T.); -#39625=ADVANCED_FACE('',(#39624),#39617,.F.); -#39632=EDGE_CURVE('',#21331,#19689,#13710,.T.); -#39638=ADVANCED_FACE('',(#39637),#39630,.F.); -#39645=EDGE_CURVE('',#21329,#19687,#13714,.T.); -#39651=ADVANCED_FACE('',(#39650),#39643,.F.); -#39658=EDGE_CURVE('',#21327,#19685,#13718,.T.); -#39664=ADVANCED_FACE('',(#39663),#39656,.F.); -#39676=ADVANCED_FACE('',(#39675),#39669,.F.); -#39683=EDGE_CURVE('',#21376,#19734,#13726,.T.); -#39686=EDGE_CURVE('',#21377,#19735,#13794,.T.); -#39690=ADVANCED_FACE('',(#39689),#39681,.F.); -#39697=EDGE_CURVE('',#21409,#19767,#13730,.T.); -#39703=ADVANCED_FACE('',(#39702),#39695,.F.); -#39710=EDGE_CURVE('',#21407,#19765,#13734,.T.); -#39716=ADVANCED_FACE('',(#39715),#39708,.F.); -#39723=EDGE_CURVE('',#21405,#19763,#13738,.T.); -#39729=ADVANCED_FACE('',(#39728),#39721,.F.); -#39736=EDGE_CURVE('',#21403,#19761,#13742,.T.); -#39742=ADVANCED_FACE('',(#39741),#39734,.F.); -#39749=EDGE_CURVE('',#21401,#19759,#13746,.T.); -#39755=ADVANCED_FACE('',(#39754),#39747,.F.); -#39762=EDGE_CURVE('',#21399,#19757,#13750,.T.); -#39768=ADVANCED_FACE('',(#39767),#39760,.F.); -#39775=EDGE_CURVE('',#21397,#19755,#13754,.T.); -#39781=ADVANCED_FACE('',(#39780),#39773,.F.); -#39788=EDGE_CURVE('',#21395,#19753,#13758,.T.); -#39794=ADVANCED_FACE('',(#39793),#39786,.F.); -#39801=EDGE_CURVE('',#21393,#19751,#13762,.T.); -#39807=ADVANCED_FACE('',(#39806),#39799,.F.); -#39814=EDGE_CURVE('',#21391,#19749,#13766,.T.); -#39820=ADVANCED_FACE('',(#39819),#39812,.F.); -#39827=EDGE_CURVE('',#21389,#19747,#13770,.T.); -#39833=ADVANCED_FACE('',(#39832),#39825,.F.); -#39840=EDGE_CURVE('',#21387,#19745,#13774,.T.); -#39846=ADVANCED_FACE('',(#39845),#39838,.F.); -#39853=EDGE_CURVE('',#21385,#19743,#13778,.T.); -#39859=ADVANCED_FACE('',(#39858),#39851,.F.); -#39866=EDGE_CURVE('',#21383,#19741,#13782,.T.); -#39872=ADVANCED_FACE('',(#39871),#39864,.F.); -#39879=EDGE_CURVE('',#21381,#19739,#13786,.T.); -#39885=ADVANCED_FACE('',(#39884),#39877,.F.); -#39892=EDGE_CURVE('',#21379,#19737,#13790,.T.); -#39898=ADVANCED_FACE('',(#39897),#39890,.F.); -#39910=ADVANCED_FACE('',(#39909),#39903,.F.); -#39917=EDGE_CURVE('',#21412,#19770,#13798,.T.); -#39920=EDGE_CURVE('',#21413,#19771,#13898,.T.); -#39924=ADVANCED_FACE('',(#39923),#39915,.F.); -#39931=EDGE_CURVE('',#21461,#19819,#13802,.T.); -#39937=ADVANCED_FACE('',(#39936),#39929,.F.); -#39944=EDGE_CURVE('',#21459,#19817,#13806,.T.); -#39950=ADVANCED_FACE('',(#39949),#39942,.F.); -#39957=EDGE_CURVE('',#21457,#19815,#13810,.T.); -#39963=ADVANCED_FACE('',(#39962),#39955,.F.); -#39970=EDGE_CURVE('',#21455,#19813,#13814,.T.); -#39976=ADVANCED_FACE('',(#39975),#39968,.F.); -#39983=EDGE_CURVE('',#21453,#19811,#13818,.T.); -#39989=ADVANCED_FACE('',(#39988),#39981,.F.); -#39996=EDGE_CURVE('',#21451,#19809,#13822,.T.); -#40002=ADVANCED_FACE('',(#40001),#39994,.F.); -#40009=EDGE_CURVE('',#21449,#19807,#13826,.T.); -#40015=ADVANCED_FACE('',(#40014),#40007,.F.); -#40022=EDGE_CURVE('',#21447,#19805,#13830,.T.); -#40028=ADVANCED_FACE('',(#40027),#40020,.F.); -#40035=EDGE_CURVE('',#21445,#19803,#13834,.T.); -#40041=ADVANCED_FACE('',(#40040),#40033,.F.); -#40048=EDGE_CURVE('',#21443,#19801,#13838,.T.); -#40054=ADVANCED_FACE('',(#40053),#40046,.F.); -#40061=EDGE_CURVE('',#21441,#19799,#13842,.T.); -#40067=ADVANCED_FACE('',(#40066),#40059,.F.); -#40074=EDGE_CURVE('',#21439,#19797,#13846,.T.); -#40080=ADVANCED_FACE('',(#40079),#40072,.F.); -#40087=EDGE_CURVE('',#21437,#19795,#13850,.T.); -#40093=ADVANCED_FACE('',(#40092),#40085,.F.); -#40100=EDGE_CURVE('',#21435,#19793,#13854,.T.); -#40106=ADVANCED_FACE('',(#40105),#40098,.F.); -#40113=EDGE_CURVE('',#21433,#19791,#13858,.T.); -#40119=ADVANCED_FACE('',(#40118),#40111,.F.); -#40126=EDGE_CURVE('',#21431,#19789,#13862,.T.); -#40132=ADVANCED_FACE('',(#40131),#40124,.F.); -#40139=EDGE_CURVE('',#21429,#19787,#13866,.T.); -#40145=ADVANCED_FACE('',(#40144),#40137,.F.); -#40152=EDGE_CURVE('',#21427,#19785,#13870,.T.); -#40158=ADVANCED_FACE('',(#40157),#40150,.F.); -#40165=EDGE_CURVE('',#21425,#19783,#13874,.T.); -#40171=ADVANCED_FACE('',(#40170),#40163,.F.); -#40178=EDGE_CURVE('',#21423,#19781,#13878,.T.); -#40184=ADVANCED_FACE('',(#40183),#40176,.F.); -#40191=EDGE_CURVE('',#21421,#19779,#13882,.T.); -#40197=ADVANCED_FACE('',(#40196),#40189,.F.); -#40204=EDGE_CURVE('',#21419,#19777,#13886,.T.); -#40210=ADVANCED_FACE('',(#40209),#40202,.F.); -#40217=EDGE_CURVE('',#21417,#19775,#13890,.T.); -#40223=ADVANCED_FACE('',(#40222),#40215,.F.); -#40230=EDGE_CURVE('',#21415,#19773,#13894,.T.); -#40236=ADVANCED_FACE('',(#40235),#40228,.F.); -#40248=ADVANCED_FACE('',(#40247),#40241,.F.); -#40255=EDGE_CURVE('',#21464,#19822,#13902,.T.); -#40258=EDGE_CURVE('',#21465,#19823,#13970,.T.); -#40262=ADVANCED_FACE('',(#40261),#40253,.F.); -#40269=EDGE_CURVE('',#21497,#19855,#13906,.T.); -#40275=ADVANCED_FACE('',(#40274),#40267,.F.); -#40282=EDGE_CURVE('',#21495,#19853,#13910,.T.); -#40288=ADVANCED_FACE('',(#40287),#40280,.F.); -#40295=EDGE_CURVE('',#21493,#19851,#13914,.T.); -#40301=ADVANCED_FACE('',(#40300),#40293,.F.); -#40308=EDGE_CURVE('',#21491,#19849,#13918,.T.); -#40314=ADVANCED_FACE('',(#40313),#40306,.F.); -#40321=EDGE_CURVE('',#21489,#19847,#13922,.T.); -#40327=ADVANCED_FACE('',(#40326),#40319,.F.); -#40334=EDGE_CURVE('',#21487,#19845,#13926,.T.); -#40340=ADVANCED_FACE('',(#40339),#40332,.F.); -#40347=EDGE_CURVE('',#21485,#19843,#13930,.T.); -#40353=ADVANCED_FACE('',(#40352),#40345,.F.); -#40360=EDGE_CURVE('',#21483,#19841,#13934,.T.); -#40366=ADVANCED_FACE('',(#40365),#40358,.F.); -#40373=EDGE_CURVE('',#21481,#19839,#13938,.T.); -#40379=ADVANCED_FACE('',(#40378),#40371,.F.); -#40386=EDGE_CURVE('',#21479,#19837,#13942,.T.); -#40392=ADVANCED_FACE('',(#40391),#40384,.F.); -#40399=EDGE_CURVE('',#21477,#19835,#13946,.T.); -#40405=ADVANCED_FACE('',(#40404),#40397,.F.); -#40412=EDGE_CURVE('',#21475,#19833,#13950,.T.); -#40418=ADVANCED_FACE('',(#40417),#40410,.F.); -#40425=EDGE_CURVE('',#21473,#19831,#13954,.T.); -#40431=ADVANCED_FACE('',(#40430),#40423,.F.); -#40438=EDGE_CURVE('',#21471,#19829,#13958,.T.); -#40444=ADVANCED_FACE('',(#40443),#40436,.F.); -#40451=EDGE_CURVE('',#21469,#19827,#13962,.T.); -#40457=ADVANCED_FACE('',(#40456),#40449,.F.); -#40464=EDGE_CURVE('',#21467,#19825,#13966,.T.); -#40470=ADVANCED_FACE('',(#40469),#40462,.F.); -#40482=ADVANCED_FACE('',(#40481),#40475,.F.); -#40489=EDGE_CURVE('',#21500,#19858,#13974,.T.); -#40492=EDGE_CURVE('',#21501,#19859,#14002,.T.); -#40496=ADVANCED_FACE('',(#40495),#40487,.F.); -#40503=EDGE_CURVE('',#21513,#19871,#13978,.T.); -#40509=ADVANCED_FACE('',(#40508),#40501,.F.); -#40516=EDGE_CURVE('',#21511,#19869,#13982,.T.); -#40522=ADVANCED_FACE('',(#40521),#40514,.F.); -#40529=EDGE_CURVE('',#21509,#19867,#13986,.T.); -#40535=ADVANCED_FACE('',(#40534),#40527,.F.); -#40542=EDGE_CURVE('',#21507,#19865,#13990,.T.); -#40548=ADVANCED_FACE('',(#40547),#40540,.F.); -#40555=EDGE_CURVE('',#21505,#19863,#13994,.T.); -#40561=ADVANCED_FACE('',(#40560),#40553,.F.); -#40568=EDGE_CURVE('',#21503,#19861,#13998,.T.); -#40574=ADVANCED_FACE('',(#40573),#40566,.F.); -#40586=ADVANCED_FACE('',(#40585),#40579,.F.); -#40593=EDGE_CURVE('',#21516,#19874,#14006,.T.); -#40596=EDGE_CURVE('',#21517,#19875,#14014,.T.); -#40600=ADVANCED_FACE('',(#40599),#40591,.F.); -#40607=EDGE_CURVE('',#21519,#19877,#14010,.T.); -#40613=ADVANCED_FACE('',(#40612),#40605,.F.); -#40625=ADVANCED_FACE('',(#40624),#40618,.F.); -#40632=EDGE_CURVE('',#21522,#19880,#14018,.T.); -#40635=EDGE_CURVE('',#21523,#19881,#14030,.T.); -#40639=ADVANCED_FACE('',(#40638),#40630,.F.); -#40646=EDGE_CURVE('',#21527,#19885,#14022,.T.); -#40652=ADVANCED_FACE('',(#40651),#40644,.F.); -#40659=EDGE_CURVE('',#21525,#19883,#14026,.T.); -#40665=ADVANCED_FACE('',(#40664),#40657,.F.); -#40677=ADVANCED_FACE('',(#40676),#40670,.F.); -#40684=EDGE_CURVE('',#21530,#19888,#14034,.T.); -#40687=EDGE_CURVE('',#21531,#19889,#14106,.T.); -#40691=ADVANCED_FACE('',(#40690),#40682,.F.); -#40698=EDGE_CURVE('',#21565,#19923,#14038,.T.); -#40704=ADVANCED_FACE('',(#40703),#40696,.F.); -#40711=EDGE_CURVE('',#21563,#19921,#14042,.T.); -#40717=ADVANCED_FACE('',(#40716),#40709,.F.); -#40724=EDGE_CURVE('',#21561,#19919,#14046,.T.); -#40730=ADVANCED_FACE('',(#40729),#40722,.F.); -#40737=EDGE_CURVE('',#21559,#19917,#14050,.T.); -#40743=ADVANCED_FACE('',(#40742),#40735,.F.); -#40750=EDGE_CURVE('',#21557,#19915,#14054,.T.); -#40756=ADVANCED_FACE('',(#40755),#40748,.F.); -#40763=EDGE_CURVE('',#21555,#19913,#14058,.T.); -#40769=ADVANCED_FACE('',(#40768),#40761,.F.); -#40776=EDGE_CURVE('',#21553,#19911,#14062,.T.); -#40782=ADVANCED_FACE('',(#40781),#40774,.F.); -#40789=EDGE_CURVE('',#21551,#19909,#14066,.T.); -#40795=ADVANCED_FACE('',(#40794),#40787,.F.); -#40802=EDGE_CURVE('',#21549,#19907,#14070,.T.); -#40808=ADVANCED_FACE('',(#40807),#40800,.F.); -#40815=EDGE_CURVE('',#21547,#19905,#14074,.T.); -#40821=ADVANCED_FACE('',(#40820),#40813,.F.); -#40828=EDGE_CURVE('',#21545,#19903,#14078,.T.); -#40834=ADVANCED_FACE('',(#40833),#40826,.F.); -#40841=EDGE_CURVE('',#21543,#19901,#14082,.T.); -#40847=ADVANCED_FACE('',(#40846),#40839,.F.); -#40854=EDGE_CURVE('',#21541,#19899,#14086,.T.); -#40860=ADVANCED_FACE('',(#40859),#40852,.F.); -#40867=EDGE_CURVE('',#21539,#19897,#14090,.T.); -#40873=ADVANCED_FACE('',(#40872),#40865,.F.); -#40880=EDGE_CURVE('',#21537,#19895,#14094,.T.); -#40886=ADVANCED_FACE('',(#40885),#40878,.F.); -#40893=EDGE_CURVE('',#21535,#19893,#14098,.T.); -#40899=ADVANCED_FACE('',(#40898),#40891,.F.); -#40906=EDGE_CURVE('',#21533,#19891,#14102,.T.); -#40912=ADVANCED_FACE('',(#40911),#40904,.F.); -#40924=ADVANCED_FACE('',(#40923),#40917,.F.); -#40931=EDGE_CURVE('',#21568,#19926,#14110,.T.); -#40934=EDGE_CURVE('',#21569,#19927,#14146,.T.); -#40938=ADVANCED_FACE('',(#40937),#40929,.F.); -#40945=EDGE_CURVE('',#21585,#19943,#14114,.T.); -#40951=ADVANCED_FACE('',(#40950),#40943,.F.); -#40958=EDGE_CURVE('',#21583,#19941,#14118,.T.); -#40964=ADVANCED_FACE('',(#40963),#40956,.F.); -#40971=EDGE_CURVE('',#21581,#19939,#14122,.T.); -#40977=ADVANCED_FACE('',(#40976),#40969,.F.); -#40984=EDGE_CURVE('',#21579,#19937,#14126,.T.); -#40990=ADVANCED_FACE('',(#40989),#40982,.F.); -#40997=EDGE_CURVE('',#21577,#19935,#14130,.T.); -#41003=ADVANCED_FACE('',(#41002),#40995,.F.); -#41010=EDGE_CURVE('',#21575,#19933,#14134,.T.); -#41016=ADVANCED_FACE('',(#41015),#41008,.F.); -#41023=EDGE_CURVE('',#21573,#19931,#14138,.T.); -#41029=ADVANCED_FACE('',(#41028),#41021,.F.); -#41036=EDGE_CURVE('',#21571,#19929,#14142,.T.); -#41042=ADVANCED_FACE('',(#41041),#41034,.F.); -#41054=ADVANCED_FACE('',(#41053),#41047,.F.); -#41061=EDGE_CURVE('',#21588,#19946,#14150,.T.); -#41064=EDGE_CURVE('',#21589,#19947,#14186,.T.); -#41068=ADVANCED_FACE('',(#41067),#41059,.F.); -#41075=EDGE_CURVE('',#21605,#19963,#14154,.T.); -#41081=ADVANCED_FACE('',(#41080),#41073,.F.); -#41088=EDGE_CURVE('',#21603,#19961,#14158,.T.); -#41094=ADVANCED_FACE('',(#41093),#41086,.F.); -#41101=EDGE_CURVE('',#21601,#19959,#14162,.T.); -#41107=ADVANCED_FACE('',(#41106),#41099,.F.); -#41114=EDGE_CURVE('',#21599,#19957,#14166,.T.); -#41120=ADVANCED_FACE('',(#41119),#41112,.F.); -#41127=EDGE_CURVE('',#21597,#19955,#14170,.T.); -#41133=ADVANCED_FACE('',(#41132),#41125,.F.); -#41140=EDGE_CURVE('',#21595,#19953,#14174,.T.); -#41146=ADVANCED_FACE('',(#41145),#41138,.F.); -#41153=EDGE_CURVE('',#21593,#19951,#14178,.T.); -#41159=ADVANCED_FACE('',(#41158),#41151,.F.); -#41166=EDGE_CURVE('',#21591,#19949,#14182,.T.); -#41172=ADVANCED_FACE('',(#41171),#41164,.F.); -#41184=ADVANCED_FACE('',(#41183),#41177,.F.); -#41191=EDGE_CURVE('',#21608,#19966,#14190,.T.); -#41194=EDGE_CURVE('',#21609,#19967,#14218,.T.); -#41198=ADVANCED_FACE('',(#41197),#41189,.F.); -#41205=EDGE_CURVE('',#21621,#19979,#14194,.T.); -#41211=ADVANCED_FACE('',(#41210),#41203,.F.); -#41218=EDGE_CURVE('',#21619,#19977,#14198,.T.); -#41224=ADVANCED_FACE('',(#41223),#41216,.F.); -#41231=EDGE_CURVE('',#21617,#19975,#14202,.T.); -#41237=ADVANCED_FACE('',(#41236),#41229,.F.); -#41244=EDGE_CURVE('',#21615,#19973,#14206,.T.); -#41250=ADVANCED_FACE('',(#41249),#41242,.F.); -#41257=EDGE_CURVE('',#21613,#19971,#14210,.T.); -#41263=ADVANCED_FACE('',(#41262),#41255,.F.); -#41270=EDGE_CURVE('',#21611,#19969,#14214,.T.); -#41276=ADVANCED_FACE('',(#41275),#41268,.F.); -#41288=ADVANCED_FACE('',(#41287),#41281,.F.); -#41295=EDGE_CURVE('',#21624,#19982,#14222,.T.); -#41298=EDGE_CURVE('',#21625,#19983,#14354,.T.); -#41302=ADVANCED_FACE('',(#41301),#41293,.F.); -#41309=EDGE_CURVE('',#21689,#20047,#14226,.T.); -#41315=ADVANCED_FACE('',(#41314),#41307,.F.); -#41322=EDGE_CURVE('',#21687,#20045,#14230,.T.); -#41328=ADVANCED_FACE('',(#41327),#41320,.F.); -#41335=EDGE_CURVE('',#21685,#20043,#14234,.T.); -#41341=ADVANCED_FACE('',(#41340),#41333,.F.); -#41348=EDGE_CURVE('',#21683,#20041,#14238,.T.); -#41354=ADVANCED_FACE('',(#41353),#41346,.F.); -#41361=EDGE_CURVE('',#21681,#20039,#14242,.T.); -#41367=ADVANCED_FACE('',(#41366),#41359,.F.); -#41374=EDGE_CURVE('',#21679,#20037,#14246,.T.); -#41380=ADVANCED_FACE('',(#41379),#41372,.F.); -#41387=EDGE_CURVE('',#21677,#20035,#14250,.T.); -#41393=ADVANCED_FACE('',(#41392),#41385,.F.); -#41400=EDGE_CURVE('',#21675,#20033,#14254,.T.); -#41406=ADVANCED_FACE('',(#41405),#41398,.F.); -#41413=EDGE_CURVE('',#21673,#20031,#14258,.T.); -#41419=ADVANCED_FACE('',(#41418),#41411,.F.); -#41426=EDGE_CURVE('',#21671,#20029,#14262,.T.); -#41432=ADVANCED_FACE('',(#41431),#41424,.F.); -#41439=EDGE_CURVE('',#21669,#20027,#14266,.T.); -#41445=ADVANCED_FACE('',(#41444),#41437,.F.); -#41452=EDGE_CURVE('',#21667,#20025,#14270,.T.); -#41458=ADVANCED_FACE('',(#41457),#41450,.F.); -#41465=EDGE_CURVE('',#21665,#20023,#14274,.T.); -#41471=ADVANCED_FACE('',(#41470),#41463,.F.); -#41478=EDGE_CURVE('',#21663,#20021,#14278,.T.); -#41484=ADVANCED_FACE('',(#41483),#41476,.F.); -#41491=EDGE_CURVE('',#21661,#20019,#14282,.T.); -#41497=ADVANCED_FACE('',(#41496),#41489,.F.); -#41504=EDGE_CURVE('',#21659,#20017,#14286,.T.); -#41510=ADVANCED_FACE('',(#41509),#41502,.F.); -#41517=EDGE_CURVE('',#21657,#20015,#14290,.T.); -#41523=ADVANCED_FACE('',(#41522),#41515,.F.); -#41530=EDGE_CURVE('',#21655,#20013,#14294,.T.); -#41536=ADVANCED_FACE('',(#41535),#41528,.F.); -#41543=EDGE_CURVE('',#21653,#20011,#14298,.T.); -#41549=ADVANCED_FACE('',(#41548),#41541,.F.); -#41556=EDGE_CURVE('',#21651,#20009,#14302,.T.); -#41562=ADVANCED_FACE('',(#41561),#41554,.F.); -#41569=EDGE_CURVE('',#21649,#20007,#14306,.T.); -#41575=ADVANCED_FACE('',(#41574),#41567,.F.); -#41582=EDGE_CURVE('',#21647,#20005,#14310,.T.); -#41588=ADVANCED_FACE('',(#41587),#41580,.F.); -#41595=EDGE_CURVE('',#21645,#20003,#14314,.T.); -#41601=ADVANCED_FACE('',(#41600),#41593,.F.); -#41608=EDGE_CURVE('',#21643,#20001,#14318,.T.); -#41614=ADVANCED_FACE('',(#41613),#41606,.F.); -#41621=EDGE_CURVE('',#21641,#19999,#14322,.T.); -#41627=ADVANCED_FACE('',(#41626),#41619,.F.); -#41634=EDGE_CURVE('',#21639,#19997,#14326,.T.); -#41640=ADVANCED_FACE('',(#41639),#41632,.F.); -#41647=EDGE_CURVE('',#21637,#19995,#14330,.T.); -#41653=ADVANCED_FACE('',(#41652),#41645,.F.); -#41660=EDGE_CURVE('',#21635,#19993,#14334,.T.); -#41666=ADVANCED_FACE('',(#41665),#41658,.F.); -#41673=EDGE_CURVE('',#21633,#19991,#14338,.T.); -#41679=ADVANCED_FACE('',(#41678),#41671,.F.); -#41686=EDGE_CURVE('',#21631,#19989,#14342,.T.); -#41692=ADVANCED_FACE('',(#41691),#41684,.F.); -#41699=EDGE_CURVE('',#21629,#19987,#14346,.T.); -#41705=ADVANCED_FACE('',(#41704),#41697,.F.); -#41712=EDGE_CURVE('',#21627,#19985,#14350,.T.); -#41718=ADVANCED_FACE('',(#41717),#41710,.F.); -#41730=ADVANCED_FACE('',(#41729),#41723,.F.); -#41737=EDGE_CURVE('',#21692,#20050,#14358,.T.); -#41740=EDGE_CURVE('',#21693,#20051,#14418,.T.); -#41744=ADVANCED_FACE('',(#41743),#41735,.F.); -#41751=EDGE_CURVE('',#21721,#20079,#14362,.T.); -#41757=ADVANCED_FACE('',(#41756),#41749,.F.); -#41764=EDGE_CURVE('',#21719,#20077,#14366,.T.); -#41770=ADVANCED_FACE('',(#41769),#41762,.F.); -#41777=EDGE_CURVE('',#21717,#20075,#14370,.T.); -#41783=ADVANCED_FACE('',(#41782),#41775,.F.); -#41790=EDGE_CURVE('',#21715,#20073,#14374,.T.); -#41796=ADVANCED_FACE('',(#41795),#41788,.F.); -#41803=EDGE_CURVE('',#21713,#20071,#14378,.T.); -#41809=ADVANCED_FACE('',(#41808),#41801,.F.); -#41816=EDGE_CURVE('',#21711,#20069,#14382,.T.); -#41822=ADVANCED_FACE('',(#41821),#41814,.F.); -#41829=EDGE_CURVE('',#21709,#20067,#14386,.T.); -#41835=ADVANCED_FACE('',(#41834),#41827,.F.); -#41842=EDGE_CURVE('',#21707,#20065,#14390,.T.); -#41848=ADVANCED_FACE('',(#41847),#41840,.F.); -#41855=EDGE_CURVE('',#21705,#20063,#14394,.T.); -#41861=ADVANCED_FACE('',(#41860),#41853,.F.); -#41868=EDGE_CURVE('',#21703,#20061,#14398,.T.); -#41874=ADVANCED_FACE('',(#41873),#41866,.F.); -#41881=EDGE_CURVE('',#21701,#20059,#14402,.T.); -#41887=ADVANCED_FACE('',(#41886),#41879,.F.); -#41894=EDGE_CURVE('',#21699,#20057,#14406,.T.); -#41900=ADVANCED_FACE('',(#41899),#41892,.F.); -#41907=EDGE_CURVE('',#21697,#20055,#14410,.T.); -#41913=ADVANCED_FACE('',(#41912),#41905,.F.); -#41920=EDGE_CURVE('',#21695,#20053,#14414,.T.); -#41926=ADVANCED_FACE('',(#41925),#41918,.F.); -#41938=ADVANCED_FACE('',(#41937),#41931,.F.); -#41945=EDGE_CURVE('',#21724,#20082,#14422,.T.); -#41948=EDGE_CURVE('',#21725,#20083,#14482,.T.); -#41952=ADVANCED_FACE('',(#41951),#41943,.F.); -#41959=EDGE_CURVE('',#21753,#20111,#14426,.T.); -#41965=ADVANCED_FACE('',(#41964),#41957,.F.); -#41972=EDGE_CURVE('',#21751,#20109,#14430,.T.); -#41978=ADVANCED_FACE('',(#41977),#41970,.F.); -#41985=EDGE_CURVE('',#21749,#20107,#14434,.T.); -#41991=ADVANCED_FACE('',(#41990),#41983,.F.); -#41998=EDGE_CURVE('',#21747,#20105,#14438,.T.); -#42004=ADVANCED_FACE('',(#42003),#41996,.F.); -#42011=EDGE_CURVE('',#21745,#20103,#14442,.T.); -#42017=ADVANCED_FACE('',(#42016),#42009,.F.); -#42024=EDGE_CURVE('',#21743,#20101,#14446,.T.); -#42030=ADVANCED_FACE('',(#42029),#42022,.F.); -#42037=EDGE_CURVE('',#21741,#20099,#14450,.T.); -#42043=ADVANCED_FACE('',(#42042),#42035,.F.); -#42050=EDGE_CURVE('',#21739,#20097,#14454,.T.); -#42056=ADVANCED_FACE('',(#42055),#42048,.F.); -#42063=EDGE_CURVE('',#21737,#20095,#14458,.T.); -#42069=ADVANCED_FACE('',(#42068),#42061,.F.); -#42076=EDGE_CURVE('',#21735,#20093,#14462,.T.); -#42082=ADVANCED_FACE('',(#42081),#42074,.F.); -#42089=EDGE_CURVE('',#21733,#20091,#14466,.T.); -#42095=ADVANCED_FACE('',(#42094),#42087,.F.); -#42102=EDGE_CURVE('',#21731,#20089,#14470,.T.); -#42108=ADVANCED_FACE('',(#42107),#42100,.F.); -#42115=EDGE_CURVE('',#21729,#20087,#14474,.T.); -#42121=ADVANCED_FACE('',(#42120),#42113,.F.); -#42128=EDGE_CURVE('',#21727,#20085,#14478,.T.); -#42134=ADVANCED_FACE('',(#42133),#42126,.F.); -#42146=ADVANCED_FACE('',(#42145),#42139,.F.); -#42153=EDGE_CURVE('',#21756,#20114,#14486,.T.); -#42156=EDGE_CURVE('',#21757,#20115,#14710,.T.); -#42160=ADVANCED_FACE('',(#42159),#42151,.F.); -#42167=EDGE_CURVE('',#21867,#20225,#14490,.T.); -#42173=ADVANCED_FACE('',(#42172),#42165,.F.); -#42180=EDGE_CURVE('',#21865,#20223,#14494,.T.); -#42186=ADVANCED_FACE('',(#42185),#42178,.F.); -#42193=EDGE_CURVE('',#21863,#20221,#14498,.T.); -#42199=ADVANCED_FACE('',(#42198),#42191,.F.); -#42206=EDGE_CURVE('',#21861,#20219,#14502,.T.); -#42212=ADVANCED_FACE('',(#42211),#42204,.F.); -#42219=EDGE_CURVE('',#21859,#20217,#14506,.T.); -#42225=ADVANCED_FACE('',(#42224),#42217,.F.); -#42232=EDGE_CURVE('',#21857,#20215,#14510,.T.); -#42238=ADVANCED_FACE('',(#42237),#42230,.F.); -#42245=EDGE_CURVE('',#21855,#20213,#14514,.T.); -#42251=ADVANCED_FACE('',(#42250),#42243,.F.); -#42258=EDGE_CURVE('',#21853,#20211,#14518,.T.); -#42264=ADVANCED_FACE('',(#42263),#42256,.F.); -#42271=EDGE_CURVE('',#21851,#20209,#14522,.T.); -#42277=ADVANCED_FACE('',(#42276),#42269,.F.); -#42284=EDGE_CURVE('',#21849,#20207,#14526,.T.); -#42290=ADVANCED_FACE('',(#42289),#42282,.F.); -#42297=EDGE_CURVE('',#21847,#20205,#14530,.T.); -#42303=ADVANCED_FACE('',(#42302),#42295,.F.); -#42310=EDGE_CURVE('',#21845,#20203,#14534,.T.); -#42316=ADVANCED_FACE('',(#42315),#42308,.F.); -#42323=EDGE_CURVE('',#21843,#20201,#14538,.T.); -#42329=ADVANCED_FACE('',(#42328),#42321,.F.); -#42336=EDGE_CURVE('',#21841,#20199,#14542,.T.); -#42342=ADVANCED_FACE('',(#42341),#42334,.F.); -#42349=EDGE_CURVE('',#21839,#20197,#14546,.T.); -#42355=ADVANCED_FACE('',(#42354),#42347,.F.); -#42362=EDGE_CURVE('',#21837,#20195,#14550,.T.); -#42368=ADVANCED_FACE('',(#42367),#42360,.F.); -#42375=EDGE_CURVE('',#21835,#20193,#14554,.T.); -#42381=ADVANCED_FACE('',(#42380),#42373,.F.); -#42388=EDGE_CURVE('',#21833,#20191,#14558,.T.); -#42394=ADVANCED_FACE('',(#42393),#42386,.F.); -#42401=EDGE_CURVE('',#21831,#20189,#14562,.T.); -#42407=ADVANCED_FACE('',(#42406),#42399,.F.); -#42414=EDGE_CURVE('',#21829,#20187,#14566,.T.); -#42420=ADVANCED_FACE('',(#42419),#42412,.F.); -#42427=EDGE_CURVE('',#21827,#20185,#14570,.T.); -#42433=ADVANCED_FACE('',(#42432),#42425,.F.); -#42440=EDGE_CURVE('',#21825,#20183,#14574,.T.); -#42446=ADVANCED_FACE('',(#42445),#42438,.F.); -#42453=EDGE_CURVE('',#21823,#20181,#14578,.T.); -#42459=ADVANCED_FACE('',(#42458),#42451,.F.); -#42466=EDGE_CURVE('',#21821,#20179,#14582,.T.); -#42472=ADVANCED_FACE('',(#42471),#42464,.F.); -#42479=EDGE_CURVE('',#21819,#20177,#14586,.T.); -#42485=ADVANCED_FACE('',(#42484),#42477,.F.); -#42492=EDGE_CURVE('',#21817,#20175,#14590,.T.); -#42498=ADVANCED_FACE('',(#42497),#42490,.F.); -#42505=EDGE_CURVE('',#21815,#20173,#14594,.T.); -#42511=ADVANCED_FACE('',(#42510),#42503,.F.); -#42518=EDGE_CURVE('',#21813,#20171,#14598,.T.); -#42524=ADVANCED_FACE('',(#42523),#42516,.F.); -#42531=EDGE_CURVE('',#21811,#20169,#14602,.T.); -#42537=ADVANCED_FACE('',(#42536),#42529,.F.); -#42544=EDGE_CURVE('',#21809,#20167,#14606,.T.); -#42550=ADVANCED_FACE('',(#42549),#42542,.F.); -#42557=EDGE_CURVE('',#21807,#20165,#14610,.T.); -#42563=ADVANCED_FACE('',(#42562),#42555,.F.); -#42570=EDGE_CURVE('',#21805,#20163,#14614,.T.); -#42576=ADVANCED_FACE('',(#42575),#42568,.F.); -#42583=EDGE_CURVE('',#21803,#20161,#14618,.T.); -#42589=ADVANCED_FACE('',(#42588),#42581,.F.); -#42596=EDGE_CURVE('',#21801,#20159,#14622,.T.); -#42602=ADVANCED_FACE('',(#42601),#42594,.F.); -#42609=EDGE_CURVE('',#21799,#20157,#14626,.T.); -#42615=ADVANCED_FACE('',(#42614),#42607,.F.); -#42622=EDGE_CURVE('',#21797,#20155,#14630,.T.); -#42628=ADVANCED_FACE('',(#42627),#42620,.F.); -#42635=EDGE_CURVE('',#21795,#20153,#14634,.T.); -#42641=ADVANCED_FACE('',(#42640),#42633,.F.); -#42648=EDGE_CURVE('',#21793,#20151,#14638,.T.); -#42654=ADVANCED_FACE('',(#42653),#42646,.F.); -#42661=EDGE_CURVE('',#21791,#20149,#14642,.T.); -#42667=ADVANCED_FACE('',(#42666),#42659,.F.); -#42674=EDGE_CURVE('',#21789,#20147,#14646,.T.); -#42680=ADVANCED_FACE('',(#42679),#42672,.F.); -#42687=EDGE_CURVE('',#21787,#20145,#14650,.T.); -#42693=ADVANCED_FACE('',(#42692),#42685,.F.); -#42700=EDGE_CURVE('',#21785,#20143,#14654,.T.); -#42706=ADVANCED_FACE('',(#42705),#42698,.F.); -#42713=EDGE_CURVE('',#21783,#20141,#14658,.T.); -#42719=ADVANCED_FACE('',(#42718),#42711,.F.); -#42726=EDGE_CURVE('',#21781,#20139,#14662,.T.); -#42732=ADVANCED_FACE('',(#42731),#42724,.F.); -#42739=EDGE_CURVE('',#21779,#20137,#14666,.T.); -#42745=ADVANCED_FACE('',(#42744),#42737,.F.); -#42752=EDGE_CURVE('',#21777,#20135,#14670,.T.); -#42758=ADVANCED_FACE('',(#42757),#42750,.F.); -#42765=EDGE_CURVE('',#21775,#20133,#14674,.T.); -#42771=ADVANCED_FACE('',(#42770),#42763,.F.); -#42778=EDGE_CURVE('',#21773,#20131,#14678,.T.); -#42784=ADVANCED_FACE('',(#42783),#42776,.F.); -#42791=EDGE_CURVE('',#21771,#20129,#14682,.T.); -#42797=ADVANCED_FACE('',(#42796),#42789,.F.); -#42804=EDGE_CURVE('',#21769,#20127,#14686,.T.); -#42810=ADVANCED_FACE('',(#42809),#42802,.F.); -#42817=EDGE_CURVE('',#21767,#20125,#14690,.T.); -#42823=ADVANCED_FACE('',(#42822),#42815,.F.); -#42830=EDGE_CURVE('',#21765,#20123,#14694,.T.); -#42836=ADVANCED_FACE('',(#42835),#42828,.F.); -#42843=EDGE_CURVE('',#21763,#20121,#14698,.T.); -#42849=ADVANCED_FACE('',(#42848),#42841,.F.); -#42856=EDGE_CURVE('',#21761,#20119,#14702,.T.); -#42862=ADVANCED_FACE('',(#42861),#42854,.F.); -#42869=EDGE_CURVE('',#21759,#20117,#14706,.T.); -#42875=ADVANCED_FACE('',(#42874),#42867,.F.); -#42887=ADVANCED_FACE('',(#42886),#42880,.F.); -#42894=EDGE_CURVE('',#21870,#20228,#14714,.T.); -#42897=EDGE_CURVE('',#21871,#20229,#14822,.T.); -#42901=ADVANCED_FACE('',(#42900),#42892,.F.); -#42908=EDGE_CURVE('',#21923,#20281,#14718,.T.); -#42914=ADVANCED_FACE('',(#42913),#42906,.F.); -#42921=EDGE_CURVE('',#21921,#20279,#14722,.T.); -#42927=ADVANCED_FACE('',(#42926),#42919,.F.); -#42934=EDGE_CURVE('',#21919,#20277,#14726,.T.); -#42940=ADVANCED_FACE('',(#42939),#42932,.F.); -#42947=EDGE_CURVE('',#21917,#20275,#14730,.T.); -#42953=ADVANCED_FACE('',(#42952),#42945,.F.); -#42960=EDGE_CURVE('',#21915,#20273,#14734,.T.); -#42966=ADVANCED_FACE('',(#42965),#42958,.F.); -#42973=EDGE_CURVE('',#21913,#20271,#14738,.T.); -#42979=ADVANCED_FACE('',(#42978),#42971,.F.); -#42986=EDGE_CURVE('',#21911,#20269,#14742,.T.); -#42992=ADVANCED_FACE('',(#42991),#42984,.F.); -#42999=EDGE_CURVE('',#21909,#20267,#14746,.T.); -#43005=ADVANCED_FACE('',(#43004),#42997,.F.); -#43012=EDGE_CURVE('',#21907,#20265,#14750,.T.); -#43018=ADVANCED_FACE('',(#43017),#43010,.F.); -#43025=EDGE_CURVE('',#21905,#20263,#14754,.T.); -#43031=ADVANCED_FACE('',(#43030),#43023,.F.); -#43038=EDGE_CURVE('',#21903,#20261,#14758,.T.); -#43044=ADVANCED_FACE('',(#43043),#43036,.F.); -#43051=EDGE_CURVE('',#21901,#20259,#14762,.T.); -#43057=ADVANCED_FACE('',(#43056),#43049,.F.); -#43064=EDGE_CURVE('',#21899,#20257,#14766,.T.); -#43070=ADVANCED_FACE('',(#43069),#43062,.F.); -#43077=EDGE_CURVE('',#21897,#20255,#14770,.T.); -#43083=ADVANCED_FACE('',(#43082),#43075,.F.); -#43090=EDGE_CURVE('',#21895,#20253,#14774,.T.); -#43096=ADVANCED_FACE('',(#43095),#43088,.F.); -#43103=EDGE_CURVE('',#21893,#20251,#14778,.T.); -#43109=ADVANCED_FACE('',(#43108),#43101,.F.); -#43116=EDGE_CURVE('',#21891,#20249,#14782,.T.); -#43122=ADVANCED_FACE('',(#43121),#43114,.F.); -#43129=EDGE_CURVE('',#21889,#20247,#14786,.T.); -#43135=ADVANCED_FACE('',(#43134),#43127,.F.); -#43142=EDGE_CURVE('',#21887,#20245,#14790,.T.); -#43148=ADVANCED_FACE('',(#43147),#43140,.F.); -#43155=EDGE_CURVE('',#21885,#20243,#14794,.T.); -#43161=ADVANCED_FACE('',(#43160),#43153,.F.); -#43168=EDGE_CURVE('',#21883,#20241,#14798,.T.); -#43174=ADVANCED_FACE('',(#43173),#43166,.F.); -#43181=EDGE_CURVE('',#21881,#20239,#14802,.T.); -#43187=ADVANCED_FACE('',(#43186),#43179,.F.); -#43194=EDGE_CURVE('',#21879,#20237,#14806,.T.); -#43200=ADVANCED_FACE('',(#43199),#43192,.F.); -#43207=EDGE_CURVE('',#21877,#20235,#14810,.T.); -#43213=ADVANCED_FACE('',(#43212),#43205,.F.); -#43220=EDGE_CURVE('',#21875,#20233,#14814,.T.); -#43226=ADVANCED_FACE('',(#43225),#43218,.F.); -#43233=EDGE_CURVE('',#21873,#20231,#14818,.T.); -#43239=ADVANCED_FACE('',(#43238),#43231,.F.); -#43251=ADVANCED_FACE('',(#43250),#43244,.F.); -#43258=EDGE_CURVE('',#22032,#21926,#14826,.T.); -#43260=EDGE_CURVE('',#21926,#21927,#14842,.T.); -#43262=EDGE_CURVE('',#22033,#21927,#14838,.T.); -#43266=ADVANCED_FACE('',(#43265),#43256,.F.); -#43274=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43267,#43268,#43269,#43270,#43271, -#43272,#43273),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,5.026351216587E-2,5.E-1, -9.497364878341E-1,1.E0),.UNSPECIFIED.); -#43279=EDGE_CURVE('',#22035,#21929,#14830,.T.); -#43281=EDGE_CURVE('',#21929,#21926,#14847,.T.); -#43286=ADVANCED_FACE('',(#43285),#43277,.F.); -#43295=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43287,#43288,#43289,#43290,#43291, -#43292,#43293,#43294),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,4),(0.E0, -3.003031208427E-2,3.487491615378E-1,6.512668908741E-1,9.699857403277E-1,1.E0), -.UNSPECIFIED.); -#43300=EDGE_CURVE('',#22034,#21928,#14834,.T.); -#43302=EDGE_CURVE('',#21928,#21929,#14854,.T.); -#43307=ADVANCED_FACE('',(#43306),#43298,.F.); -#43316=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43308,#43309,#43310,#43311,#43312, -#43313,#43314,#43315),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,4),(0.E0, -1.770776597802E-1,3.924467325861E-1,6.075621244159E-1,8.229311972182E-1,1.E0), -.UNSPECIFIED.); -#43322=EDGE_CURVE('',#21927,#21928,#14861,.T.); -#43327=ADVANCED_FACE('',(#43326),#43319,.F.); -#43339=ADVANCED_FACE('',(#43338),#43332,.T.); -#43352=EDGE_CURVE('',#21930,#21931,#14875,.T.); -#43354=EDGE_CURVE('',#21931,#21930,#14879,.T.); -#43358=ADVANCED_FACE('',(#43357),#43351,.T.); -#43371=EDGE_CURVE('',#21936,#21937,#14918,.T.); -#43373=EDGE_CURVE('',#21950,#21936,#14923,.T.); -#43375=EDGE_CURVE('',#21948,#21950,#14927,.T.); -#43377=EDGE_CURVE('',#21947,#21948,#14932,.T.); -#43379=EDGE_CURVE('',#21945,#21947,#14936,.T.); -#43381=EDGE_CURVE('',#21943,#21945,#14940,.T.); -#43383=EDGE_CURVE('',#21942,#21943,#14945,.T.); -#43385=EDGE_CURVE('',#21940,#21942,#14949,.T.); -#43387=EDGE_CURVE('',#21939,#21940,#14954,.T.); -#43389=EDGE_CURVE('',#21937,#21939,#14958,.T.); -#43393=ADVANCED_FACE('',(#43392),#43370,.T.); -#43406=EDGE_CURVE('',#21957,#21958,#14976,.T.); -#43408=EDGE_CURVE('',#21967,#21957,#14981,.T.); -#43410=EDGE_CURVE('',#21965,#21967,#14985,.T.); -#43412=EDGE_CURVE('',#21964,#21965,#14990,.T.); -#43414=EDGE_CURVE('',#21962,#21964,#14994,.T.); -#43416=EDGE_CURVE('',#21961,#21962,#14999,.T.); -#43418=EDGE_CURVE('',#21959,#21961,#15003,.T.); -#43420=EDGE_CURVE('',#21958,#21959,#15008,.T.); -#43424=EDGE_CURVE('',#21951,#21952,#14963,.T.); -#43426=EDGE_CURVE('',#21954,#21951,#14968,.T.); -#43428=EDGE_CURVE('',#21952,#21954,#14972,.T.); -#43432=ADVANCED_FACE('',(#43423,#43431),#43405,.T.); -#43445=EDGE_CURVE('',#21970,#21971,#15012,.T.); -#43447=EDGE_CURVE('',#21983,#21970,#15017,.T.); -#43449=EDGE_CURVE('',#21981,#21983,#15021,.T.); -#43451=EDGE_CURVE('',#21980,#21981,#15026,.T.); -#43453=EDGE_CURVE('',#21978,#21980,#15030,.T.); -#43455=EDGE_CURVE('',#21977,#21978,#15035,.T.); -#43457=EDGE_CURVE('',#21975,#21977,#15039,.T.); -#43459=EDGE_CURVE('',#21974,#21975,#15044,.T.); -#43461=EDGE_CURVE('',#21972,#21974,#15048,.T.); -#43463=EDGE_CURVE('',#21971,#21972,#15053,.T.); -#43467=ADVANCED_FACE('',(#43466),#43444,.T.); -#43480=EDGE_CURVE('',#21984,#21985,#15060,.T.); -#43482=EDGE_CURVE('',#22010,#21984,#15064,.T.); -#43484=EDGE_CURVE('',#22009,#22010,#15069,.T.); -#43486=EDGE_CURVE('',#22007,#22009,#15073,.T.); -#43488=EDGE_CURVE('',#22006,#22007,#15080,.T.); -#43490=EDGE_CURVE('',#22005,#22006,#15100,.T.); -#43492=EDGE_CURVE('',#22003,#22005,#15104,.T.); -#43494=EDGE_CURVE('',#22002,#22003,#15148,.T.); -#43496=EDGE_CURVE('',#22000,#22002,#15152,.T.); -#43498=EDGE_CURVE('',#21999,#22000,#15157,.T.); -#43500=EDGE_CURVE('',#21997,#21999,#15161,.T.); -#43502=EDGE_CURVE('',#21996,#21997,#15166,.T.); -#43504=EDGE_CURVE('',#21994,#21996,#15170,.T.); -#43506=EDGE_CURVE('',#21993,#21994,#15175,.T.); -#43508=EDGE_CURVE('',#21991,#21993,#15179,.T.); -#43510=EDGE_CURVE('',#21990,#21991,#15192,.T.); -#43512=EDGE_CURVE('',#21988,#21990,#15196,.T.); -#43514=EDGE_CURVE('',#21987,#21988,#15201,.T.); -#43516=EDGE_CURVE('',#21985,#21987,#15205,.T.); -#43520=EDGE_CURVE('',#21932,#21933,#14902,.T.); -#43522=EDGE_CURVE('',#21935,#21932,#14909,.T.); -#43524=EDGE_CURVE('',#21933,#21935,#14913,.T.); -#43528=EDGE_CURVE('',#22013,#22014,#15209,.T.); -#43530=EDGE_CURVE('',#22029,#22013,#15214,.T.); -#43532=EDGE_CURVE('',#22027,#22029,#15218,.T.); -#43534=EDGE_CURVE('',#22026,#22027,#15223,.T.); -#43536=EDGE_CURVE('',#22024,#22026,#15227,.T.); -#43538=EDGE_CURVE('',#22023,#22024,#15232,.T.); -#43540=EDGE_CURVE('',#22021,#22023,#15236,.T.); -#43542=EDGE_CURVE('',#22020,#22021,#15241,.T.); -#43544=EDGE_CURVE('',#22018,#22020,#15245,.T.); -#43546=EDGE_CURVE('',#22017,#22018,#15250,.T.); -#43548=EDGE_CURVE('',#22015,#22017,#15254,.T.); -#43550=EDGE_CURVE('',#22014,#22015,#15259,.T.); -#43554=ADVANCED_FACE('',(#43519,#43527,#43553),#43479,.T.); -#43577=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43562,#43563,#43564,#43565,#43566, -#43567,#43568,#43569,#43570,#43571,#43572,#43573,#43574,#43575,#43576), -.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1,1,1,4),(0.E0,9.823848988275E-3, -1.130270224621E-1,2.104668173494E-1,3.082432905291E-1,4.045890416750E-1, -5.004787657915E-1,5.963293916175E-1,6.925373046017E-1,7.901417632527E-1, -8.873425732469E-1,9.901846313284E-1,1.E0),.UNSPECIFIED.); -#43582=EDGE_CURVE('',#22036,#21930,#15263,.T.); -#43585=EDGE_CURVE('',#22037,#21931,#15267,.T.); -#43589=ADVANCED_FACE('',(#43588),#43580,.F.); -#43601=ADVANCED_FACE('',(#43600),#43594,.F.); -#43626=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43602,#43603,#43604,#43605,#43606, -#43607,#43608,#43609,#43610,#43611,#43612,#43613,#43614,#43615,#43616,#43617, -#43618,#43619,#43620,#43621,#43622,#43623,#43624,#43625),.UNSPECIFIED.,.F.,.F.,( -4,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,4),(0.E0,2.638024918130E-2, -9.697674602190E-2,1.814656886454E-1,2.640445443712E-1,3.399936776104E-1, -4.034562377740E-1,4.652690227933E-1,5.154425915404E-1,5.629283075165E-1, -6.055497727799E-1,6.431837998276E-1,6.805783382219E-1,7.234772319833E-1, -7.706644591479E-1,8.114356775201E-1,8.509751388475E-1,8.836320587725E-1, -9.136357745113E-1,9.411158515131E-1,9.737168749521E-1,1.E0),.UNSPECIFIED.); -#43631=EDGE_CURVE('',#22038,#21932,#15271,.T.); -#43634=EDGE_CURVE('',#22039,#21933,#15279,.T.); -#43638=ADVANCED_FACE('',(#43637),#43629,.F.); -#43647=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43639,#43640,#43641,#43642,#43643, -#43644,#43645,#43646),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,4),(0.E0, -6.181087353811E-2,3.556297638154E-1,6.443832454919E-1,9.382021357732E-1,1.E0), -.UNSPECIFIED.); -#43652=EDGE_CURVE('',#22041,#21935,#15275,.T.); -#43658=ADVANCED_FACE('',(#43657),#43650,.F.); -#43670=ADVANCED_FACE('',(#43669),#43663,.F.); -#43678=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43671,#43672,#43673,#43674,#43675, -#43676,#43677),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,5.988456180014E-2,5.E-1, -9.401154381999E-1,1.E0),.UNSPECIFIED.); -#43683=EDGE_CURVE('',#22043,#21936,#15283,.T.); -#43686=EDGE_CURVE('',#22042,#21937,#15319,.T.); -#43690=ADVANCED_FACE('',(#43689),#43681,.F.); -#43698=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43691,#43692,#43693,#43694,#43695, -#43696,#43697),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,5.650551850475E-2,5.E-1, -9.434944814953E-1,1.E0),.UNSPECIFIED.); -#43703=EDGE_CURVE('',#22056,#21950,#15287,.T.); -#43709=ADVANCED_FACE('',(#43708),#43701,.F.); -#43716=EDGE_CURVE('',#22054,#21948,#15291,.T.); -#43722=ADVANCED_FACE('',(#43721),#43714,.F.); -#43730=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43723,#43724,#43725,#43726,#43727, -#43728,#43729),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.552010622124E-2,5.E-1, -9.644798937788E-1,1.E0),.UNSPECIFIED.); -#43735=EDGE_CURVE('',#22053,#21947,#15295,.T.); -#43741=ADVANCED_FACE('',(#43740),#43733,.F.); -#43748=EDGE_CURVE('',#22051,#21945,#15299,.T.); -#43754=ADVANCED_FACE('',(#43753),#43746,.F.); -#43761=EDGE_CURVE('',#22049,#21943,#15303,.T.); -#43767=ADVANCED_FACE('',(#43766),#43759,.F.); -#43775=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43768,#43769,#43770,#43771,#43772, -#43773,#43774),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,5.751937587427E-2,5.E-1, -9.424806241257E-1,1.E0),.UNSPECIFIED.); -#43780=EDGE_CURVE('',#22048,#21942,#15307,.T.); -#43786=ADVANCED_FACE('',(#43785),#43778,.F.); -#43793=EDGE_CURVE('',#22046,#21940,#15311,.T.); -#43799=ADVANCED_FACE('',(#43798),#43791,.F.); -#43807=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43800,#43801,#43802,#43803,#43804, -#43805,#43806),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.548485093052E-2,5.E-1, -9.645151490695E-1,1.E0),.UNSPECIFIED.); -#43812=EDGE_CURVE('',#22045,#21939,#15315,.T.); -#43818=ADVANCED_FACE('',(#43817),#43810,.F.); -#43830=ADVANCED_FACE('',(#43829),#43823,.F.); -#43838=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43831,#43832,#43833,#43834,#43835, -#43836,#43837),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,7.353428644202E-2,5.E-1, -9.264657135580E-1,1.E0),.UNSPECIFIED.); -#43843=EDGE_CURVE('',#22058,#21951,#15323,.T.); -#43846=EDGE_CURVE('',#22057,#21952,#15331,.T.); -#43850=ADVANCED_FACE('',(#43849),#43841,.F.); -#43858=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43851,#43852,#43853,#43854,#43855, -#43856,#43857),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,6.719161080336E-2,5.E-1, -9.328083891966E-1,1.E0),.UNSPECIFIED.); -#43863=EDGE_CURVE('',#22060,#21954,#15327,.T.); -#43869=ADVANCED_FACE('',(#43868),#43861,.F.); -#43881=ADVANCED_FACE('',(#43880),#43874,.F.); -#43888=EDGE_CURVE('',#22063,#21957,#15335,.T.); -#43891=EDGE_CURVE('',#22064,#21958,#15363,.T.); -#43895=ADVANCED_FACE('',(#43894),#43886,.F.); -#43903=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43896,#43897,#43898,#43899,#43900, -#43901,#43902),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.223454479711E-2,5.E-1, -9.677654552029E-1,1.E0),.UNSPECIFIED.); -#43908=EDGE_CURVE('',#22073,#21967,#15339,.T.); -#43914=ADVANCED_FACE('',(#43913),#43906,.F.); -#43921=EDGE_CURVE('',#22071,#21965,#15343,.T.); -#43927=ADVANCED_FACE('',(#43926),#43919,.F.); -#43935=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43928,#43929,#43930,#43931,#43932, -#43933,#43934),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.741480361605E-2,5.E-1, -9.625851963839E-1,1.E0),.UNSPECIFIED.); -#43940=EDGE_CURVE('',#22070,#21964,#15347,.T.); -#43946=ADVANCED_FACE('',(#43945),#43938,.F.); -#43953=EDGE_CURVE('',#22068,#21962,#15351,.T.); -#43959=ADVANCED_FACE('',(#43958),#43951,.F.); -#43967=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43960,#43961,#43962,#43963,#43964, -#43965,#43966),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.700090049378E-1,5.E-1, -8.299909950622E-1,1.E0),.UNSPECIFIED.); -#43972=EDGE_CURVE('',#22067,#21961,#15355,.T.); -#43978=ADVANCED_FACE('',(#43977),#43970,.F.); -#43985=EDGE_CURVE('',#22065,#21959,#15359,.T.); -#43991=ADVANCED_FACE('',(#43990),#43983,.F.); -#43999=B_SPLINE_CURVE_WITH_KNOTS('',3,(#43992,#43993,#43994,#43995,#43996, -#43997,#43998),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.574761407114E-1,5.E-1, -8.425238592886E-1,1.E0),.UNSPECIFIED.); -#44009=ADVANCED_FACE('',(#44008),#44002,.F.); -#44016=EDGE_CURVE('',#22076,#21970,#15367,.T.); -#44019=EDGE_CURVE('',#22077,#21971,#15403,.T.); -#44023=ADVANCED_FACE('',(#44022),#44014,.F.); -#44031=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44024,#44025,#44026,#44027,#44028, -#44029,#44030),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.552286083906E-2,5.E-1, -9.644771391609E-1,1.E0),.UNSPECIFIED.); -#44036=EDGE_CURVE('',#22089,#21983,#15371,.T.); -#44042=ADVANCED_FACE('',(#44041),#44034,.F.); -#44049=EDGE_CURVE('',#22087,#21981,#15375,.T.); -#44055=ADVANCED_FACE('',(#44054),#44047,.F.); -#44063=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44056,#44057,#44058,#44059,#44060, -#44061,#44062),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.211263858281E-1,5.E-1, -8.788736141719E-1,1.E0),.UNSPECIFIED.); -#44068=EDGE_CURVE('',#22086,#21980,#15379,.T.); -#44074=ADVANCED_FACE('',(#44073),#44066,.F.); -#44081=EDGE_CURVE('',#22084,#21978,#15383,.T.); -#44087=ADVANCED_FACE('',(#44086),#44079,.F.); -#44095=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44088,#44089,#44090,#44091,#44092, -#44093,#44094),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.690933988132E-1,5.E-1, -8.309066011868E-1,1.E0),.UNSPECIFIED.); -#44100=EDGE_CURVE('',#22083,#21977,#15387,.T.); -#44106=ADVANCED_FACE('',(#44105),#44098,.F.); -#44113=EDGE_CURVE('',#22081,#21975,#15391,.T.); -#44119=ADVANCED_FACE('',(#44118),#44111,.F.); -#44127=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44120,#44121,#44122,#44123,#44124, -#44125,#44126),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.319268365599E-1,5.E-1, -8.680731634401E-1,1.E0),.UNSPECIFIED.); -#44132=EDGE_CURVE('',#22080,#21974,#15395,.T.); -#44138=ADVANCED_FACE('',(#44137),#44130,.F.); -#44145=EDGE_CURVE('',#22078,#21972,#15399,.T.); -#44151=ADVANCED_FACE('',(#44150),#44143,.F.); -#44159=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44152,#44153,#44154,#44155,#44156, -#44157,#44158),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,8.013014490799E-2,5.E-1, -9.198698550920E-1,1.E0),.UNSPECIFIED.); -#44169=ADVANCED_FACE('',(#44168),#44162,.F.); -#44178=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44170,#44171,#44172,#44173,#44174, -#44175,#44176,#44177),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,4),(0.E0, -7.705140566131E-2,3.600093786435E-1,6.400027835071E-1,9.229607564846E-1,1.E0), -.UNSPECIFIED.); -#44183=EDGE_CURVE('',#22090,#21984,#15407,.T.); -#44186=EDGE_CURVE('',#22091,#21985,#15479,.T.); -#44190=ADVANCED_FACE('',(#44189),#44181,.F.); -#44197=EDGE_CURVE('',#22116,#22010,#15411,.T.); -#44203=ADVANCED_FACE('',(#44202),#44195,.F.); -#44211=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44204,#44205,#44206,#44207,#44208, -#44209,#44210),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.907037077443E-1,5.E-1, -8.092962922557E-1,1.E0),.UNSPECIFIED.); -#44216=EDGE_CURVE('',#22115,#22009,#15415,.T.); -#44222=ADVANCED_FACE('',(#44221),#44214,.F.); -#44229=EDGE_CURVE('',#22113,#22007,#15419,.T.); -#44235=ADVANCED_FACE('',(#44234),#44227,.F.); -#44244=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44236,#44237,#44238,#44239,#44240, -#44241,#44242,#44243),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,4),(0.E0, -4.765898897564E-2,3.522815175884E-1,6.477326820973E-1,9.523552107088E-1,1.E0), -.UNSPECIFIED.); -#44249=EDGE_CURVE('',#22112,#22006,#15423,.T.); -#44255=ADVANCED_FACE('',(#44254),#44247,.F.); -#44277=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44256,#44257,#44258,#44259,#44260, -#44261,#44262,#44263,#44264,#44265,#44266,#44267,#44268,#44269,#44270,#44271, -#44272,#44273,#44274,#44275,#44276),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,1,1,1,1,1,1, -1,1,1,1,1,1,1,1,4),(0.E0,1.502717102866E-2,6.788731481766E-2,1.090506241370E-1, -1.446176469950E-1,1.801879315641E-1,2.205578590817E-1,2.604526206218E-1, -3.082672880676E-1,3.578079627982E-1,4.149211125913E-1,4.752350735031E-1, -5.444723745092E-1,6.209444096033E-1,7.072634917474E-1,7.969145514746E-1, -8.850027378222E-1,9.849924343924E-1,1.E0),.UNSPECIFIED.); -#44282=EDGE_CURVE('',#22111,#22005,#15427,.T.); -#44288=ADVANCED_FACE('',(#44287),#44280,.F.); -#44295=EDGE_CURVE('',#22109,#22003,#15431,.T.); -#44301=ADVANCED_FACE('',(#44300),#44293,.F.); -#44347=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44302,#44303,#44304,#44305,#44306, -#44307,#44308,#44309,#44310,#44311,#44312,#44313,#44314,#44315,#44316,#44317, -#44318,#44319,#44320,#44321,#44322,#44323,#44324,#44325,#44326,#44327,#44328, -#44329,#44330,#44331,#44332,#44333,#44334,#44335,#44336,#44337,#44338,#44339, -#44340,#44341,#44342,#44343,#44344,#44345,#44346),.UNSPECIFIED.,.F.,.F.,(4,1,1, -1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1, -4),(0.E0,9.834849914036E-3,4.309334614173E-2,6.822384302405E-2, -9.180239261608E-2,1.158640681887E-1,1.418365545464E-1,1.707978600775E-1, -2.059403696422E-1,2.397673180165E-1,2.822664351416E-1,3.305593384512E-1, -3.848597360295E-1,4.361158272450E-1,4.829306439036E-1,5.236652620871E-1, -5.611768331986E-1,5.927916933231E-1,6.215130654948E-1,6.479903926529E-1, -6.735621261508E-1,7.011848610633E-1,7.292549234523E-1,7.525636333596E-1, -7.750103702999E-1,7.930818902285E-1,8.099514424845E-1,8.252539961917E-1, -8.401644973107E-1,8.559298473261E-1,8.721616450542E-1,8.870754036626E-1, -8.999038170431E-1,9.115850037522E-1,9.219982202149E-1,9.311238775346E-1, -9.392544418246E-1,9.474699494686E-1,9.566143728156E-1,9.667257433358E-1, -9.777132986664E-1,9.901744712104E-1,1.E0),.UNSPECIFIED.); -#44352=EDGE_CURVE('',#22108,#22002,#15435,.T.); -#44358=ADVANCED_FACE('',(#44357),#44350,.F.); -#44365=EDGE_CURVE('',#22106,#22000,#15439,.T.); -#44371=ADVANCED_FACE('',(#44370),#44363,.F.); -#44379=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44372,#44373,#44374,#44375,#44376, -#44377,#44378),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,4.565475517462E-2,5.E-1, -9.543452448254E-1,1.E0),.UNSPECIFIED.); -#44384=EDGE_CURVE('',#22105,#21999,#15443,.T.); -#44390=ADVANCED_FACE('',(#44389),#44382,.F.); -#44397=EDGE_CURVE('',#22103,#21997,#15447,.T.); -#44403=ADVANCED_FACE('',(#44402),#44395,.F.); -#44411=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44404,#44405,#44406,#44407,#44408, -#44409,#44410),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,4.565365113029E-2,5.E-1, -9.543463488697E-1,1.E0),.UNSPECIFIED.); -#44416=EDGE_CURVE('',#22102,#21996,#15451,.T.); -#44422=ADVANCED_FACE('',(#44421),#44414,.F.); -#44429=EDGE_CURVE('',#22100,#21994,#15455,.T.); -#44435=ADVANCED_FACE('',(#44434),#44427,.F.); -#44443=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44436,#44437,#44438,#44439,#44440, -#44441,#44442),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.211184276351E-1,5.E-1, -8.788815723649E-1,1.E0),.UNSPECIFIED.); -#44448=EDGE_CURVE('',#22099,#21993,#15459,.T.); -#44454=ADVANCED_FACE('',(#44453),#44446,.F.); -#44461=EDGE_CURVE('',#22097,#21991,#15463,.T.); -#44467=ADVANCED_FACE('',(#44466),#44459,.F.); -#44482=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44468,#44469,#44470,#44471,#44472, -#44473,#44474,#44475,#44476,#44477,#44478,#44479,#44480,#44481),.UNSPECIFIED., -.F.,.F.,(4,1,1,1,1,1,1,1,1,1,1,4),(0.E0,9.827066850928E-3,1.250079409255E-1, -2.330825139146E-1,3.406593006908E-1,4.474920606366E-1,5.539690835245E-1, -6.606483396060E-1,7.679377868995E-1,8.755906097716E-1,9.901824554712E-1,1.E0), -.UNSPECIFIED.); -#44487=EDGE_CURVE('',#22096,#21990,#15467,.T.); -#44493=ADVANCED_FACE('',(#44492),#44485,.F.); -#44500=EDGE_CURVE('',#22094,#21988,#15471,.T.); -#44506=ADVANCED_FACE('',(#44505),#44498,.F.); -#44514=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44507,#44508,#44509,#44510,#44511, -#44512,#44513),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.549971855368E-2,5.E-1, -9.645002814463E-1,1.E0),.UNSPECIFIED.); -#44519=EDGE_CURVE('',#22093,#21987,#15475,.T.); -#44525=ADVANCED_FACE('',(#44524),#44517,.F.); -#44537=ADVANCED_FACE('',(#44536),#44530,.F.); -#44544=EDGE_CURVE('',#22119,#22013,#15483,.T.); -#44547=EDGE_CURVE('',#22120,#22014,#15527,.T.); -#44551=ADVANCED_FACE('',(#44550),#44542,.F.); -#44559=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44552,#44553,#44554,#44555,#44556, -#44557,#44558),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.321862730255E-1,5.E-1, -8.678137269745E-1,1.E0),.UNSPECIFIED.); -#44564=EDGE_CURVE('',#22135,#22029,#15487,.T.); -#44570=ADVANCED_FACE('',(#44569),#44562,.F.); -#44577=EDGE_CURVE('',#22133,#22027,#15491,.T.); -#44583=ADVANCED_FACE('',(#44582),#44575,.F.); -#44591=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44584,#44585,#44586,#44587,#44588, -#44589,#44590),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.708026551608E-1,5.E-1, -8.291973448392E-1,1.E0),.UNSPECIFIED.); -#44596=EDGE_CURVE('',#22132,#22026,#15495,.T.); -#44602=ADVANCED_FACE('',(#44601),#44594,.F.); -#44609=EDGE_CURVE('',#22130,#22024,#15499,.T.); -#44615=ADVANCED_FACE('',(#44614),#44607,.F.); -#44623=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44616,#44617,#44618,#44619,#44620, -#44621,#44622),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.214106373054E-1,5.E-1, -8.785893626946E-1,1.E0),.UNSPECIFIED.); -#44628=EDGE_CURVE('',#22129,#22023,#15503,.T.); -#44634=ADVANCED_FACE('',(#44633),#44626,.F.); -#44641=EDGE_CURVE('',#22127,#22021,#15507,.T.); -#44647=ADVANCED_FACE('',(#44646),#44639,.F.); -#44655=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44648,#44649,#44650,#44651,#44652, -#44653,#44654),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,3.552378292452E-2,5.E-1, -9.644762170755E-1,1.E0),.UNSPECIFIED.); -#44660=EDGE_CURVE('',#22126,#22020,#15511,.T.); -#44666=ADVANCED_FACE('',(#44665),#44658,.F.); -#44673=EDGE_CURVE('',#22124,#22018,#15515,.T.); -#44679=ADVANCED_FACE('',(#44678),#44671,.F.); -#44687=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44680,#44681,#44682,#44683,#44684, -#44685,#44686),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.214499814373E-1,5.E-1, -8.785500185627E-1,1.E0),.UNSPECIFIED.); -#44692=EDGE_CURVE('',#22123,#22017,#15519,.T.); -#44698=ADVANCED_FACE('',(#44697),#44690,.F.); -#44705=EDGE_CURVE('',#22121,#22015,#15523,.T.); -#44711=ADVANCED_FACE('',(#44710),#44703,.F.); -#44719=B_SPLINE_CURVE_WITH_KNOTS('',3,(#44712,#44713,#44714,#44715,#44716, -#44717,#44718),.UNSPECIFIED.,.F.,.F.,(4,1,1,1,4),(0.E0,1.613623065696E-1,5.E-1, -8.386376934304E-1,1.E0),.UNSPECIFIED.); -#44729=ADVANCED_FACE('',(#44728),#44722,.F.); -#44737=EDGE_CURVE('',#16877,#16895,#15531,.T.); -#44742=ADVANCED_FACE('',(#44741),#44734,.F.); -#44751=EDGE_CURVE('',#16876,#16894,#15535,.T.); -#44755=ADVANCED_FACE('',(#44754),#44747,.F.); -#44767=ADVANCED_FACE('',(#44766),#44760,.F.); -#44775=EDGE_CURVE('',#16883,#16901,#15539,.T.); -#44780=ADVANCED_FACE('',(#44779),#44772,.F.); -#44789=EDGE_CURVE('',#16882,#16900,#15543,.T.); -#44793=ADVANCED_FACE('',(#44792),#44785,.F.); -#44805=ADVANCED_FACE('',(#44804),#44798,.F.); -#44813=EDGE_CURVE('',#16872,#16890,#15547,.T.); -#44818=ADVANCED_FACE('',(#44817),#44810,.F.); -#44825=EDGE_CURVE('',#16873,#16891,#15551,.T.); -#44831=ADVANCED_FACE('',(#44830),#44823,.F.); -#44843=ADVANCED_FACE('',(#44842),#44836,.F.); -#44851=EDGE_CURVE('',#16840,#16856,#15555,.T.); -#44856=ADVANCED_FACE('',(#44855),#44848,.F.); -#44863=EDGE_CURVE('',#16841,#16857,#15559,.T.); -#44869=ADVANCED_FACE('',(#44868),#44861,.F.); -#44881=ADVANCED_FACE('',(#44880),#44874,.F.); -#44893=ADVANCED_FACE('',(#44892),#44886,.F.); -#44907=EDGE_CURVE('',#16806,#16818,#15573,.T.); -#44913=ADVANCED_FACE('',(#44912),#44905,.T.); -#44919=EDGE_CURVE('',#17227,#17210,#15577,.T.); -#44924=EDGE_CURVE('',#17194,#17226,#15581,.T.); -#44926=EDGE_CURVE('',#17226,#17227,#15585,.T.); -#44930=ADVANCED_FACE('',(#44929),#44918,.T.); -#44936=EDGE_CURVE('',#17259,#17178,#15589,.T.); -#44939=EDGE_CURVE('',#17231,#17215,#15593,.T.); -#44941=EDGE_CURVE('',#17230,#17231,#15597,.T.); -#44943=EDGE_CURVE('',#17199,#17230,#15601,.T.); -#44946=EDGE_CURVE('',#17162,#17258,#15605,.T.); -#44948=EDGE_CURVE('',#17258,#17259,#15609,.T.); -#44952=ADVANCED_FACE('',(#44951),#44935,.T.); -#44958=EDGE_CURVE('',#17291,#17146,#15613,.T.); -#44961=EDGE_CURVE('',#17263,#17183,#15617,.T.); -#44963=EDGE_CURVE('',#17262,#17263,#15621,.T.); -#44965=EDGE_CURVE('',#17167,#17262,#15625,.T.); -#44968=EDGE_CURVE('',#17130,#17290,#15629,.T.); -#44970=EDGE_CURVE('',#17290,#17291,#15633,.T.); -#44974=ADVANCED_FACE('',(#44973),#44957,.T.); -#44980=EDGE_CURVE('',#17323,#17114,#15637,.T.); -#44983=EDGE_CURVE('',#17295,#17151,#15641,.T.); -#44985=EDGE_CURVE('',#17294,#17295,#15645,.T.); -#44987=EDGE_CURVE('',#17135,#17294,#15649,.T.); -#44990=EDGE_CURVE('',#17098,#17322,#15653,.T.); -#44992=EDGE_CURVE('',#17322,#17323,#15657,.T.); -#44996=ADVANCED_FACE('',(#44995),#44979,.T.); -#45002=EDGE_CURVE('',#17355,#17082,#15661,.T.); -#45005=EDGE_CURVE('',#17327,#17119,#15665,.T.); -#45007=EDGE_CURVE('',#17326,#17327,#15669,.T.); -#45009=EDGE_CURVE('',#17103,#17326,#15673,.T.); -#45012=EDGE_CURVE('',#17066,#17354,#15677,.T.); -#45014=EDGE_CURVE('',#17354,#17355,#15681,.T.); -#45018=ADVANCED_FACE('',(#45017),#45001,.T.); -#45024=EDGE_CURVE('',#17387,#17050,#15685,.T.); -#45027=EDGE_CURVE('',#17359,#17087,#15689,.T.); -#45029=EDGE_CURVE('',#17358,#17359,#15693,.T.); -#45031=EDGE_CURVE('',#17071,#17358,#15697,.T.); -#45034=EDGE_CURVE('',#17034,#17386,#15701,.T.); -#45036=EDGE_CURVE('',#17386,#17387,#15705,.T.); -#45040=ADVANCED_FACE('',(#45039),#45023,.T.); -#45046=EDGE_CURVE('',#17419,#17018,#15709,.T.); -#45049=EDGE_CURVE('',#17391,#17055,#15713,.T.); -#45051=EDGE_CURVE('',#17390,#17391,#15717,.T.); -#45053=EDGE_CURVE('',#17039,#17390,#15721,.T.); -#45056=EDGE_CURVE('',#17002,#17418,#15725,.T.); -#45058=EDGE_CURVE('',#17418,#17419,#15729,.T.); -#45062=ADVANCED_FACE('',(#45061),#45045,.T.); -#45068=EDGE_CURVE('',#17451,#16986,#15733,.T.); -#45071=EDGE_CURVE('',#17423,#17023,#15737,.T.); -#45073=EDGE_CURVE('',#17422,#17423,#15741,.T.); -#45075=EDGE_CURVE('',#17007,#17422,#15745,.T.); -#45078=EDGE_CURVE('',#16970,#17450,#15749,.T.); -#45080=EDGE_CURVE('',#17450,#17451,#15753,.T.); -#45084=ADVANCED_FACE('',(#45083),#45067,.T.); -#45090=EDGE_CURVE('',#16975,#17454,#15757,.T.); -#45093=EDGE_CURVE('',#16803,#16815,#15761,.T.); -#45096=EDGE_CURVE('',#17455,#16990,#15765,.T.); -#45098=EDGE_CURVE('',#17454,#17455,#15769,.T.); -#45102=ADVANCED_FACE('',(#45101),#45089,.T.); -#45108=EDGE_CURVE('',#17226,#17241,#15773,.T.); -#45112=EDGE_CURVE('',#17241,#17195,#16057,.T.); -#45116=ADVANCED_FACE('',(#45115),#45107,.F.); -#45122=EDGE_CURVE('',#17227,#17243,#15777,.T.); -#45124=EDGE_CURVE('',#17211,#17243,#16065,.T.); -#45130=ADVANCED_FACE('',(#45129),#45121,.F.); -#45136=EDGE_CURVE('',#17222,#17233,#15791,.T.); -#45138=EDGE_CURVE('',#17233,#17237,#16011,.T.); -#45140=EDGE_CURVE('',#17237,#17218,#15995,.T.); -#45142=EDGE_CURVE('',#17218,#17222,#15782,.T.); -#45146=ADVANCED_FACE('',(#45145),#45135,.F.); -#45160=EDGE_CURVE('',#17241,#17245,#16053,.T.); -#45162=EDGE_CURVE('',#17245,#17230,#16037,.T.); -#45164=EDGE_CURVE('',#17230,#17226,#15787,.T.); -#45168=ADVANCED_FACE('',(#45167),#45158,.F.); -#45182=EDGE_CURVE('',#17186,#17222,#15819,.T.); -#45185=EDGE_CURVE('',#17233,#17187,#16015,.T.); -#45189=ADVANCED_FACE('',(#45188),#45180,.F.); -#45195=EDGE_CURVE('',#17223,#17235,#15795,.T.); -#45197=EDGE_CURVE('',#17203,#17235,#16023,.T.); -#45200=EDGE_CURVE('',#17223,#17202,#15827,.T.); -#45204=ADVANCED_FACE('',(#45203),#45194,.F.); -#45210=EDGE_CURVE('',#17191,#17218,#15799,.T.); -#45213=EDGE_CURVE('',#16799,#16811,#15803,.T.); -#45216=EDGE_CURVE('',#17219,#17207,#15807,.T.); -#45218=EDGE_CURVE('',#17218,#17219,#15811,.T.); -#45222=ADVANCED_FACE('',(#45221),#45209,.T.); -#45228=EDGE_CURVE('',#17159,#17250,#15815,.T.); -#45232=EDGE_CURVE('',#17222,#17223,#15823,.T.); -#45236=EDGE_CURVE('',#17251,#17175,#15831,.T.); -#45238=EDGE_CURVE('',#17250,#17251,#15835,.T.); -#45242=ADVANCED_FACE('',(#45241),#45227,.T.); -#45248=EDGE_CURVE('',#17127,#17282,#15839,.T.); -#45251=EDGE_CURVE('',#17154,#17254,#15843,.T.); -#45253=EDGE_CURVE('',#17254,#17255,#15847,.T.); -#45255=EDGE_CURVE('',#17255,#17170,#15851,.T.); -#45258=EDGE_CURVE('',#17283,#17143,#15855,.T.); -#45260=EDGE_CURVE('',#17282,#17283,#15859,.T.); -#45264=ADVANCED_FACE('',(#45263),#45247,.T.); -#45270=EDGE_CURVE('',#17095,#17314,#15863,.T.); -#45273=EDGE_CURVE('',#17122,#17286,#15867,.T.); -#45275=EDGE_CURVE('',#17286,#17287,#15871,.T.); -#45277=EDGE_CURVE('',#17287,#17138,#15875,.T.); -#45280=EDGE_CURVE('',#17315,#17111,#15879,.T.); -#45282=EDGE_CURVE('',#17314,#17315,#15883,.T.); -#45286=ADVANCED_FACE('',(#45285),#45269,.T.); -#45292=EDGE_CURVE('',#17063,#17346,#15887,.T.); -#45295=EDGE_CURVE('',#17090,#17318,#15891,.T.); -#45297=EDGE_CURVE('',#17318,#17319,#15895,.T.); -#45299=EDGE_CURVE('',#17319,#17106,#15899,.T.); -#45302=EDGE_CURVE('',#17347,#17079,#15903,.T.); -#45304=EDGE_CURVE('',#17346,#17347,#15907,.T.); -#45308=ADVANCED_FACE('',(#45307),#45291,.T.); -#45314=EDGE_CURVE('',#17031,#17378,#15911,.T.); -#45317=EDGE_CURVE('',#17058,#17350,#15915,.T.); -#45319=EDGE_CURVE('',#17350,#17351,#15919,.T.); -#45321=EDGE_CURVE('',#17351,#17074,#15923,.T.); -#45324=EDGE_CURVE('',#17379,#17047,#15927,.T.); -#45326=EDGE_CURVE('',#17378,#17379,#15931,.T.); -#45330=ADVANCED_FACE('',(#45329),#45313,.T.); -#45336=EDGE_CURVE('',#16999,#17410,#15935,.T.); -#45339=EDGE_CURVE('',#17026,#17382,#15939,.T.); -#45341=EDGE_CURVE('',#17382,#17383,#15943,.T.); -#45343=EDGE_CURVE('',#17383,#17042,#15947,.T.); -#45346=EDGE_CURVE('',#17411,#17015,#15951,.T.); -#45348=EDGE_CURVE('',#17410,#17411,#15955,.T.); -#45352=ADVANCED_FACE('',(#45351),#45335,.T.); -#45358=EDGE_CURVE('',#16967,#17442,#15959,.T.); -#45361=EDGE_CURVE('',#16994,#17414,#15963,.T.); -#45363=EDGE_CURVE('',#17414,#17415,#15967,.T.); -#45365=EDGE_CURVE('',#17415,#17010,#15971,.T.); -#45368=EDGE_CURVE('',#17443,#16983,#15975,.T.); -#45370=EDGE_CURVE('',#17442,#17443,#15979,.T.); -#45374=ADVANCED_FACE('',(#45373),#45357,.T.); -#45380=EDGE_CURVE('',#17447,#16978,#15983,.T.); -#45383=EDGE_CURVE('',#16802,#16814,#16773,.T.); -#45386=EDGE_CURVE('',#16962,#17446,#15987,.T.); -#45388=EDGE_CURVE('',#17446,#17447,#15991,.T.); -#45392=ADVANCED_FACE('',(#45391),#45379,.T.); -#45399=EDGE_CURVE('',#17237,#17189,#15999,.T.); -#45405=ADVANCED_FACE('',(#45404),#45397,.F.); -#45411=EDGE_CURVE('',#17239,#17219,#16003,.T.); -#45415=EDGE_CURVE('',#17205,#17239,#16007,.T.); -#45419=ADVANCED_FACE('',(#45418),#45410,.F.); -#45431=ADVANCED_FACE('',(#45430),#45424,.F.); -#45437=EDGE_CURVE('',#17235,#17239,#16019,.T.); -#45444=ADVANCED_FACE('',(#45443),#45436,.F.); -#45451=EDGE_CURVE('',#17219,#17223,#16028,.T.); -#45457=ADVANCED_FACE('',(#45456),#45449,.T.); -#45471=EDGE_CURVE('',#17231,#17227,#16033,.T.); -#45473=EDGE_CURVE('',#17247,#17231,#16045,.T.); -#45475=EDGE_CURVE('',#17243,#17247,#16061,.T.); -#45479=ADVANCED_FACE('',(#45478),#45469,.T.); -#45498=ADVANCED_FACE('',(#45497),#45491,.F.); -#45517=ADVANCED_FACE('',(#45516),#45510,.F.); -#45531=EDGE_CURVE('',#17245,#17197,#16041,.T.); -#45537=ADVANCED_FACE('',(#45536),#45529,.F.); -#45546=EDGE_CURVE('',#17213,#17247,#16049,.T.); -#45550=ADVANCED_FACE('',(#45549),#45542,.F.); -#45562=ADVANCED_FACE('',(#45561),#45555,.F.); -#45574=ADVANCED_FACE('',(#45573),#45567,.F.); -#45586=ADVANCED_FACE('',(#45585),#45579,.T.); -#45592=EDGE_CURVE('',#17269,#17250,#16073,.T.); -#45594=EDGE_CURVE('',#17269,#17157,#16077,.T.); -#45600=ADVANCED_FACE('',(#45599),#45591,.F.); -#45606=EDGE_CURVE('',#17271,#17251,#16081,.T.); -#45610=EDGE_CURVE('',#17173,#17271,#16085,.T.); -#45614=ADVANCED_FACE('',(#45613),#45605,.F.); -#45620=EDGE_CURVE('',#17254,#17265,#16099,.T.); -#45622=EDGE_CURVE('',#17265,#17269,#16107,.T.); -#45625=EDGE_CURVE('',#17250,#17254,#16090,.T.); -#45629=ADVANCED_FACE('',(#45628),#45619,.F.); -#45642=EDGE_CURVE('',#17258,#17273,#16133,.T.); -#45644=EDGE_CURVE('',#17273,#17277,#16141,.T.); -#45646=EDGE_CURVE('',#17277,#17262,#16157,.T.); -#45648=EDGE_CURVE('',#17262,#17258,#16095,.T.); -#45652=ADVANCED_FACE('',(#45651),#45641,.F.); -#45668=EDGE_CURVE('',#17265,#17155,#16111,.T.); -#45672=ADVANCED_FACE('',(#45671),#45664,.F.); -#45678=EDGE_CURVE('',#17255,#17267,#16103,.T.); -#45680=EDGE_CURVE('',#17171,#17267,#16119,.T.); -#45686=ADVANCED_FACE('',(#45685),#45677,.F.); -#45698=ADVANCED_FACE('',(#45697),#45691,.F.); -#45704=EDGE_CURVE('',#17267,#17271,#16115,.T.); -#45711=ADVANCED_FACE('',(#45710),#45703,.F.); -#45718=EDGE_CURVE('',#17251,#17255,#16124,.T.); -#45724=ADVANCED_FACE('',(#45723),#45716,.T.); -#45737=EDGE_CURVE('',#17259,#17275,#16137,.T.); -#45739=EDGE_CURVE('',#17263,#17259,#16129,.T.); -#45741=EDGE_CURVE('',#17279,#17263,#16165,.T.); -#45743=EDGE_CURVE('',#17275,#17279,#16149,.T.); -#45747=ADVANCED_FACE('',(#45746),#45736,.T.); -#45766=ADVANCED_FACE('',(#45765),#45759,.F.); -#45782=EDGE_CURVE('',#17273,#17163,#16145,.T.); -#45786=ADVANCED_FACE('',(#45785),#45778,.F.); -#45793=EDGE_CURVE('',#17179,#17275,#16153,.T.); -#45799=ADVANCED_FACE('',(#45798),#45791,.F.); -#45808=EDGE_CURVE('',#17277,#17165,#16161,.T.); -#45812=ADVANCED_FACE('',(#45811),#45804,.F.); -#45819=EDGE_CURVE('',#17181,#17279,#16169,.T.); -#45825=ADVANCED_FACE('',(#45824),#45817,.F.); -#45837=ADVANCED_FACE('',(#45836),#45830,.F.); -#45849=ADVANCED_FACE('',(#45848),#45842,.F.); -#45861=ADVANCED_FACE('',(#45860),#45854,.F.); -#45874=EDGE_CURVE('',#17301,#17282,#16173,.T.); -#45876=EDGE_CURVE('',#17301,#17125,#16177,.T.); -#45882=ADVANCED_FACE('',(#45881),#45873,.F.); -#45888=EDGE_CURVE('',#17303,#17283,#16181,.T.); -#45892=EDGE_CURVE('',#17141,#17303,#16185,.T.); -#45896=ADVANCED_FACE('',(#45895),#45887,.F.); -#45902=EDGE_CURVE('',#17286,#17297,#16199,.T.); -#45904=EDGE_CURVE('',#17297,#17301,#16207,.T.); -#45907=EDGE_CURVE('',#17282,#17286,#16190,.T.); -#45911=ADVANCED_FACE('',(#45910),#45901,.F.); -#45924=EDGE_CURVE('',#17290,#17305,#16233,.T.); -#45926=EDGE_CURVE('',#17305,#17309,#16241,.T.); -#45928=EDGE_CURVE('',#17309,#17294,#16257,.T.); -#45930=EDGE_CURVE('',#17294,#17290,#16195,.T.); -#45934=ADVANCED_FACE('',(#45933),#45923,.F.); -#45950=EDGE_CURVE('',#17297,#17123,#16211,.T.); -#45954=ADVANCED_FACE('',(#45953),#45946,.F.); -#45960=EDGE_CURVE('',#17287,#17299,#16203,.T.); -#45962=EDGE_CURVE('',#17139,#17299,#16219,.T.); -#45968=ADVANCED_FACE('',(#45967),#45959,.F.); -#45980=ADVANCED_FACE('',(#45979),#45973,.F.); -#45986=EDGE_CURVE('',#17299,#17303,#16215,.T.); -#45993=ADVANCED_FACE('',(#45992),#45985,.F.); -#46000=EDGE_CURVE('',#17283,#17287,#16224,.T.); -#46006=ADVANCED_FACE('',(#46005),#45998,.T.); -#46019=EDGE_CURVE('',#17291,#17307,#16237,.T.); -#46021=EDGE_CURVE('',#17295,#17291,#16229,.T.); -#46023=EDGE_CURVE('',#17311,#17295,#16265,.T.); -#46025=EDGE_CURVE('',#17307,#17311,#16249,.T.); -#46029=ADVANCED_FACE('',(#46028),#46018,.T.); -#46048=ADVANCED_FACE('',(#46047),#46041,.F.); -#46064=EDGE_CURVE('',#17305,#17131,#16245,.T.); -#46068=ADVANCED_FACE('',(#46067),#46060,.F.); -#46075=EDGE_CURVE('',#17147,#17307,#16253,.T.); -#46081=ADVANCED_FACE('',(#46080),#46073,.F.); -#46090=EDGE_CURVE('',#17309,#17133,#16261,.T.); -#46094=ADVANCED_FACE('',(#46093),#46086,.F.); -#46101=EDGE_CURVE('',#17149,#17311,#16269,.T.); -#46107=ADVANCED_FACE('',(#46106),#46099,.F.); -#46119=ADVANCED_FACE('',(#46118),#46112,.F.); -#46131=ADVANCED_FACE('',(#46130),#46124,.F.); -#46143=ADVANCED_FACE('',(#46142),#46136,.F.); -#46156=EDGE_CURVE('',#17333,#17314,#16273,.T.); -#46158=EDGE_CURVE('',#17333,#17093,#16277,.T.); -#46164=ADVANCED_FACE('',(#46163),#46155,.F.); -#46170=EDGE_CURVE('',#17335,#17315,#16281,.T.); -#46174=EDGE_CURVE('',#17109,#17335,#16285,.T.); -#46178=ADVANCED_FACE('',(#46177),#46169,.F.); -#46184=EDGE_CURVE('',#17318,#17329,#16299,.T.); -#46186=EDGE_CURVE('',#17329,#17333,#16307,.T.); -#46189=EDGE_CURVE('',#17314,#17318,#16290,.T.); -#46193=ADVANCED_FACE('',(#46192),#46183,.F.); -#46206=EDGE_CURVE('',#17322,#17337,#16333,.T.); -#46208=EDGE_CURVE('',#17337,#17341,#16341,.T.); -#46210=EDGE_CURVE('',#17341,#17326,#16357,.T.); -#46212=EDGE_CURVE('',#17326,#17322,#16295,.T.); -#46216=ADVANCED_FACE('',(#46215),#46205,.F.); -#46232=EDGE_CURVE('',#17329,#17091,#16311,.T.); -#46236=ADVANCED_FACE('',(#46235),#46228,.F.); -#46242=EDGE_CURVE('',#17319,#17331,#16303,.T.); -#46244=EDGE_CURVE('',#17107,#17331,#16319,.T.); -#46250=ADVANCED_FACE('',(#46249),#46241,.F.); -#46262=ADVANCED_FACE('',(#46261),#46255,.F.); -#46268=EDGE_CURVE('',#17331,#17335,#16315,.T.); -#46275=ADVANCED_FACE('',(#46274),#46267,.F.); -#46282=EDGE_CURVE('',#17315,#17319,#16324,.T.); -#46288=ADVANCED_FACE('',(#46287),#46280,.T.); -#46301=EDGE_CURVE('',#17323,#17339,#16337,.T.); -#46303=EDGE_CURVE('',#17327,#17323,#16329,.T.); -#46305=EDGE_CURVE('',#17343,#17327,#16365,.T.); -#46307=EDGE_CURVE('',#17339,#17343,#16349,.T.); -#46311=ADVANCED_FACE('',(#46310),#46300,.T.); -#46330=ADVANCED_FACE('',(#46329),#46323,.F.); -#46346=EDGE_CURVE('',#17337,#17099,#16345,.T.); -#46350=ADVANCED_FACE('',(#46349),#46342,.F.); -#46357=EDGE_CURVE('',#17115,#17339,#16353,.T.); -#46363=ADVANCED_FACE('',(#46362),#46355,.F.); -#46372=EDGE_CURVE('',#17341,#17101,#16361,.T.); -#46376=ADVANCED_FACE('',(#46375),#46368,.F.); -#46383=EDGE_CURVE('',#17117,#17343,#16369,.T.); -#46389=ADVANCED_FACE('',(#46388),#46381,.F.); -#46401=ADVANCED_FACE('',(#46400),#46394,.F.); -#46413=ADVANCED_FACE('',(#46412),#46406,.F.); -#46425=ADVANCED_FACE('',(#46424),#46418,.F.); -#46438=EDGE_CURVE('',#17365,#17346,#16373,.T.); -#46440=EDGE_CURVE('',#17365,#17061,#16377,.T.); -#46446=ADVANCED_FACE('',(#46445),#46437,.F.); -#46452=EDGE_CURVE('',#17367,#17347,#16381,.T.); -#46456=EDGE_CURVE('',#17077,#17367,#16385,.T.); -#46460=ADVANCED_FACE('',(#46459),#46451,.F.); -#46466=EDGE_CURVE('',#17350,#17361,#16399,.T.); -#46468=EDGE_CURVE('',#17361,#17365,#16407,.T.); -#46471=EDGE_CURVE('',#17346,#17350,#16390,.T.); -#46475=ADVANCED_FACE('',(#46474),#46465,.F.); -#46488=EDGE_CURVE('',#17354,#17369,#16433,.T.); -#46490=EDGE_CURVE('',#17369,#17373,#16441,.T.); -#46492=EDGE_CURVE('',#17373,#17358,#16457,.T.); -#46494=EDGE_CURVE('',#17358,#17354,#16395,.T.); -#46498=ADVANCED_FACE('',(#46497),#46487,.F.); -#46514=EDGE_CURVE('',#17361,#17059,#16411,.T.); -#46518=ADVANCED_FACE('',(#46517),#46510,.F.); -#46524=EDGE_CURVE('',#17351,#17363,#16403,.T.); -#46526=EDGE_CURVE('',#17075,#17363,#16419,.T.); -#46532=ADVANCED_FACE('',(#46531),#46523,.F.); -#46544=ADVANCED_FACE('',(#46543),#46537,.F.); -#46550=EDGE_CURVE('',#17363,#17367,#16415,.T.); -#46557=ADVANCED_FACE('',(#46556),#46549,.F.); -#46564=EDGE_CURVE('',#17347,#17351,#16424,.T.); -#46570=ADVANCED_FACE('',(#46569),#46562,.T.); -#46583=EDGE_CURVE('',#17355,#17371,#16437,.T.); -#46585=EDGE_CURVE('',#17359,#17355,#16429,.T.); -#46587=EDGE_CURVE('',#17375,#17359,#16465,.T.); -#46589=EDGE_CURVE('',#17371,#17375,#16449,.T.); -#46593=ADVANCED_FACE('',(#46592),#46582,.T.); -#46612=ADVANCED_FACE('',(#46611),#46605,.F.); -#46628=EDGE_CURVE('',#17369,#17067,#16445,.T.); -#46632=ADVANCED_FACE('',(#46631),#46624,.F.); -#46639=EDGE_CURVE('',#17083,#17371,#16453,.T.); -#46645=ADVANCED_FACE('',(#46644),#46637,.F.); -#46654=EDGE_CURVE('',#17373,#17069,#16461,.T.); -#46658=ADVANCED_FACE('',(#46657),#46650,.F.); -#46665=EDGE_CURVE('',#17085,#17375,#16469,.T.); -#46671=ADVANCED_FACE('',(#46670),#46663,.F.); -#46683=ADVANCED_FACE('',(#46682),#46676,.F.); -#46695=ADVANCED_FACE('',(#46694),#46688,.F.); -#46707=ADVANCED_FACE('',(#46706),#46700,.F.); -#46720=EDGE_CURVE('',#17397,#17378,#16473,.T.); -#46722=EDGE_CURVE('',#17397,#17029,#16477,.T.); -#46728=ADVANCED_FACE('',(#46727),#46719,.F.); -#46734=EDGE_CURVE('',#17399,#17379,#16481,.T.); -#46738=EDGE_CURVE('',#17045,#17399,#16485,.T.); -#46742=ADVANCED_FACE('',(#46741),#46733,.F.); -#46748=EDGE_CURVE('',#17382,#17393,#16499,.T.); -#46750=EDGE_CURVE('',#17393,#17397,#16507,.T.); -#46753=EDGE_CURVE('',#17378,#17382,#16490,.T.); -#46757=ADVANCED_FACE('',(#46756),#46747,.F.); -#46770=EDGE_CURVE('',#17386,#17401,#16533,.T.); -#46772=EDGE_CURVE('',#17401,#17405,#16541,.T.); -#46774=EDGE_CURVE('',#17405,#17390,#16557,.T.); -#46776=EDGE_CURVE('',#17390,#17386,#16495,.T.); -#46780=ADVANCED_FACE('',(#46779),#46769,.F.); -#46796=EDGE_CURVE('',#17393,#17027,#16511,.T.); -#46800=ADVANCED_FACE('',(#46799),#46792,.F.); -#46806=EDGE_CURVE('',#17383,#17395,#16503,.T.); -#46808=EDGE_CURVE('',#17043,#17395,#16519,.T.); -#46814=ADVANCED_FACE('',(#46813),#46805,.F.); -#46826=ADVANCED_FACE('',(#46825),#46819,.F.); -#46832=EDGE_CURVE('',#17395,#17399,#16515,.T.); -#46839=ADVANCED_FACE('',(#46838),#46831,.F.); -#46846=EDGE_CURVE('',#17379,#17383,#16524,.T.); -#46852=ADVANCED_FACE('',(#46851),#46844,.T.); -#46865=EDGE_CURVE('',#17387,#17403,#16537,.T.); -#46867=EDGE_CURVE('',#17391,#17387,#16529,.T.); -#46869=EDGE_CURVE('',#17407,#17391,#16565,.T.); -#46871=EDGE_CURVE('',#17403,#17407,#16549,.T.); -#46875=ADVANCED_FACE('',(#46874),#46864,.T.); -#46894=ADVANCED_FACE('',(#46893),#46887,.F.); -#46910=EDGE_CURVE('',#17401,#17035,#16545,.T.); -#46914=ADVANCED_FACE('',(#46913),#46906,.F.); -#46921=EDGE_CURVE('',#17051,#17403,#16553,.T.); -#46927=ADVANCED_FACE('',(#46926),#46919,.F.); -#46936=EDGE_CURVE('',#17405,#17037,#16561,.T.); -#46940=ADVANCED_FACE('',(#46939),#46932,.F.); -#46947=EDGE_CURVE('',#17053,#17407,#16569,.T.); -#46953=ADVANCED_FACE('',(#46952),#46945,.F.); -#46965=ADVANCED_FACE('',(#46964),#46958,.F.); -#46977=ADVANCED_FACE('',(#46976),#46970,.F.); -#46989=ADVANCED_FACE('',(#46988),#46982,.F.); -#47002=EDGE_CURVE('',#17429,#17410,#16573,.T.); -#47004=EDGE_CURVE('',#17429,#16997,#16577,.T.); -#47010=ADVANCED_FACE('',(#47009),#47001,.F.); -#47016=EDGE_CURVE('',#17431,#17411,#16581,.T.); -#47020=EDGE_CURVE('',#17013,#17431,#16585,.T.); -#47024=ADVANCED_FACE('',(#47023),#47015,.F.); -#47030=EDGE_CURVE('',#17414,#17425,#16599,.T.); -#47032=EDGE_CURVE('',#17425,#17429,#16607,.T.); -#47035=EDGE_CURVE('',#17410,#17414,#16590,.T.); -#47039=ADVANCED_FACE('',(#47038),#47029,.F.); -#47052=EDGE_CURVE('',#17418,#17433,#16633,.T.); -#47054=EDGE_CURVE('',#17433,#17437,#16641,.T.); -#47056=EDGE_CURVE('',#17437,#17422,#16657,.T.); -#47058=EDGE_CURVE('',#17422,#17418,#16595,.T.); -#47062=ADVANCED_FACE('',(#47061),#47051,.F.); -#47078=EDGE_CURVE('',#17425,#16995,#16611,.T.); -#47082=ADVANCED_FACE('',(#47081),#47074,.F.); -#47088=EDGE_CURVE('',#17415,#17427,#16603,.T.); -#47090=EDGE_CURVE('',#17011,#17427,#16619,.T.); -#47096=ADVANCED_FACE('',(#47095),#47087,.F.); -#47108=ADVANCED_FACE('',(#47107),#47101,.F.); -#47114=EDGE_CURVE('',#17427,#17431,#16615,.T.); -#47121=ADVANCED_FACE('',(#47120),#47113,.F.); -#47128=EDGE_CURVE('',#17411,#17415,#16624,.T.); -#47134=ADVANCED_FACE('',(#47133),#47126,.T.); -#47147=EDGE_CURVE('',#17419,#17435,#16637,.T.); -#47149=EDGE_CURVE('',#17423,#17419,#16629,.T.); -#47151=EDGE_CURVE('',#17439,#17423,#16665,.T.); -#47153=EDGE_CURVE('',#17435,#17439,#16649,.T.); -#47157=ADVANCED_FACE('',(#47156),#47146,.T.); -#47176=ADVANCED_FACE('',(#47175),#47169,.F.); -#47192=EDGE_CURVE('',#17433,#17003,#16645,.T.); -#47196=ADVANCED_FACE('',(#47195),#47188,.F.); -#47203=EDGE_CURVE('',#17019,#17435,#16653,.T.); -#47209=ADVANCED_FACE('',(#47208),#47201,.F.); -#47218=EDGE_CURVE('',#17437,#17005,#16661,.T.); -#47222=ADVANCED_FACE('',(#47221),#47214,.F.); -#47229=EDGE_CURVE('',#17021,#17439,#16669,.T.); -#47235=ADVANCED_FACE('',(#47234),#47227,.F.); -#47247=ADVANCED_FACE('',(#47246),#47240,.F.); -#47259=ADVANCED_FACE('',(#47258),#47252,.F.); -#47271=ADVANCED_FACE('',(#47270),#47264,.F.); -#47284=EDGE_CURVE('',#17461,#17442,#16673,.T.); -#47286=EDGE_CURVE('',#17461,#16965,#16677,.T.); -#47292=ADVANCED_FACE('',(#47291),#47283,.F.); -#47298=EDGE_CURVE('',#17463,#17443,#16681,.T.); -#47302=EDGE_CURVE('',#16981,#17463,#16685,.T.); -#47306=ADVANCED_FACE('',(#47305),#47297,.F.); -#47312=EDGE_CURVE('',#17446,#17457,#16699,.T.); -#47314=EDGE_CURVE('',#17457,#17461,#16707,.T.); -#47317=EDGE_CURVE('',#17442,#17446,#16690,.T.); -#47321=ADVANCED_FACE('',(#47320),#47311,.F.); -#47334=EDGE_CURVE('',#17450,#17465,#16733,.T.); -#47336=EDGE_CURVE('',#17465,#17469,#16741,.T.); -#47338=EDGE_CURVE('',#17469,#17454,#16757,.T.); -#47340=EDGE_CURVE('',#17454,#17450,#16695,.T.); -#47344=ADVANCED_FACE('',(#47343),#47333,.F.); -#47360=EDGE_CURVE('',#17457,#16963,#16711,.T.); -#47364=ADVANCED_FACE('',(#47363),#47356,.F.); -#47370=EDGE_CURVE('',#17447,#17459,#16703,.T.); -#47372=EDGE_CURVE('',#16979,#17459,#16719,.T.); -#47378=ADVANCED_FACE('',(#47377),#47369,.F.); -#47390=ADVANCED_FACE('',(#47389),#47383,.F.); -#47396=EDGE_CURVE('',#17459,#17463,#16715,.T.); -#47403=ADVANCED_FACE('',(#47402),#47395,.F.); -#47410=EDGE_CURVE('',#17443,#17447,#16724,.T.); -#47416=ADVANCED_FACE('',(#47415),#47408,.T.); -#47429=EDGE_CURVE('',#17451,#17467,#16737,.T.); -#47431=EDGE_CURVE('',#17455,#17451,#16729,.T.); -#47433=EDGE_CURVE('',#17471,#17455,#16765,.T.); -#47435=EDGE_CURVE('',#17467,#17471,#16749,.T.); -#47439=ADVANCED_FACE('',(#47438),#47428,.T.); -#47458=ADVANCED_FACE('',(#47457),#47451,.F.); -#47474=EDGE_CURVE('',#17465,#16971,#16745,.T.); -#47478=ADVANCED_FACE('',(#47477),#47470,.F.); -#47485=EDGE_CURVE('',#16987,#17467,#16753,.T.); -#47491=ADVANCED_FACE('',(#47490),#47483,.F.); -#47500=EDGE_CURVE('',#17469,#16973,#16761,.T.); -#47504=ADVANCED_FACE('',(#47503),#47496,.F.); -#47511=EDGE_CURVE('',#16991,#17471,#16769,.T.); -#47517=ADVANCED_FACE('',(#47516),#47509,.F.); -#47529=ADVANCED_FACE('',(#47528),#47522,.F.); -#47541=ADVANCED_FACE('',(#47540),#47534,.F.); -#47553=ADVANCED_FACE('',(#47552),#47546,.F.); -#47572=ADVANCED_FACE('',(#47571),#47565,.T.); -#47584=ADVANCED_FACE('',(#47583),#47577,.F.); -#47598=EDGE_CURVE('',#17507,#17491,#16787,.T.); -#47604=ADVANCED_FACE('',(#47603),#47596,.F.); -#47611=EDGE_CURVE('',#17506,#17490,#16791,.T.); -#47617=ADVANCED_FACE('',(#47616),#47609,.F.); -#47629=ADVANCED_FACE('',(#47628),#47622,.F.); -#47641=ADVANCED_FACE('',(#47640),#47634,.F.); -#47644=(LENGTH_UNIT()NAMED_UNIT(*)SI_UNIT(.MILLI.,.METRE.)); -#47646=(NAMED_UNIT(*)PLANE_ANGLE_UNIT()SI_UNIT($,.RADIAN.)); -#47649=(NAMED_UNIT(*)SI_UNIT($,.STERADIAN.)SOLID_ANGLE_UNIT()); -#47651=(GEOMETRIC_REPRESENTATION_CONTEXT(3)GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT(( -#47650))GLOBAL_UNIT_ASSIGNED_CONTEXT((#47644,#47648,#47649))REPRESENTATION_CONTEXT('ID1','3')); -#47652=ADVANCED_BREP_SHAPE_REPRESENTATION('',(#47643),#47651); -#47660=PRODUCT_DEFINITION('design','',#47659,#47656); -#47661=PRODUCT_DEFINITION_SHAPE('','SHAPE FOR BT832X.',#47660); -#47662=SHAPE_DEFINITION_REPRESENTATION(#47661,#47652); -ENDSEC; -END-ISO-10303-21; diff --git a/PCB/v2.x/libraries/3dmodels/ESP32-S3-MINI-1U.step b/PCB/v2.x/libraries/3dmodels/ESP32-S3-MINI-1U.step new file mode 100755 index 0000000..b83c8c3 --- /dev/null +++ b/PCB/v2.x/libraries/3dmodels/ESP32-S3-MINI-1U.step @@ -0,0 +1,105868 @@ +ISO-10303-21; +HEADER; +FILE_DESCRIPTION (( 'STEP AP214' ), + '1' ); +FILE_NAME ('ESP32-S3-MINI-1U_V1_3D.STEP', + '2023-12-27T08:50:49', + ( 'Windows User' ), + ( 'P R C' ), + 'SwSTEP 2.0', + 'SolidWorks 2022', + '' ); +FILE_SCHEMA (( 'AUTOMOTIVE_DESIGN' )); +ENDSEC; + +DATA; +#1 = ORIENTED_EDGE ( 'NONE', *, *, #23808, .F. ) ; +#2 = ORIENTED_EDGE ( 'NONE', *, *, #6333, .T. ) ; +#3 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43713, 'distance_accuracy_value', 'NONE'); +#4 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21229, 'distance_accuracy_value', 'NONE'); +#5 = STYLED_ITEM ( 'NONE', ( #94694 ), #44646 ) ; +#6 = LINE ( 'NONE', #37829, #85710 ) ; +#7 = FILL_AREA_STYLE_COLOUR ( '', #64299 ) ; +#8 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, 0.2399999999999999911 ) ) ; +#9 = PRESENTATION_STYLE_ASSIGNMENT (( #78630 ) ) ; +#10 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 2.438701000000000008, 0.8648700000000000276 ) ) ; +#11 = FILL_AREA_STYLE_COLOUR ( '', #65202 ) ; +#12 = ORIENTED_EDGE ( 'NONE', *, *, #20302, .F. ) ; +#13 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.09999999999999853451, 0.8299999999999999600 ) ) ; +#14 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#15 = SURFACE_STYLE_FILL_AREA ( #69964 ) ; +#16 = VERTEX_POINT ( 'NONE', #82607 ) ; +#17 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#18 = STYLED_ITEM ( 'NONE', ( #49919 ), #33371 ) ; +#19 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.1199999999999999956, -0.6500000000000001332 ) ) ; +#20 = ORIENTED_EDGE ( 'NONE', *, *, #32133, .T. ) ; +#21 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22 = EDGE_CURVE ( 'NONE', #42884, #42036, #90211, .T. ) ; +#23 = CARTESIAN_POINT ( 'NONE', ( 1.036940038338219905, -1.318596846191909977, 0.8299999999999999600 ) ) ; +#24 = FILL_AREA_STYLE_COLOUR ( '', #49572 ) ; +#25 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78908 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9912, #18133, #2867 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#28 = DIRECTION ( 'NONE', ( -0.7071067811865480168, -0.7071067811865470176, 0.000000000000000000 ) ) ; +#29 = CARTESIAN_POINT ( 'NONE', ( 1.841287855068439949, -1.152628822534790043, 0.8299999999999999600 ) ) ; +#30 = SURFACE_STYLE_USAGE ( .BOTH. , #54176 ) ; +#31 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33 = EDGE_LOOP ( 'NONE', ( #54585, #35149, #51993, #29981 ) ) ; +#32 = EDGE_LOOP ( 'NONE', ( #4081, #43053, #42481, #15473 ) ) ; +#34 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35 = EDGE_LOOP ( 'NONE', ( #96478, #72903, #60180, #34209 ) ) ; +#36 = EDGE_CURVE ( 'NONE', #79398, #26719, #2985, .T. ) ; +#38 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39 = EDGE_LOOP ( 'NONE', ( #51184, #37768, #2805, #63867 ) ) ; +#40 = EDGE_CURVE ( 'NONE', #43255, #93936, #22304, .T. ) ; +#41 = ORIENTED_EDGE ( 'NONE', *, *, #1715, .F. ) ; +#42 = EDGE_CURVE ( 'NONE', #38892, #93243, #37646, .T. ) ; +#43 = CARTESIAN_POINT ( 'NONE', ( 5.080897750250088052, 3.266015249749912197, 0.8648700000000000276 ) ) ; +#44 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#45 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6483 ), #83240 ) ; +#47 = SURFACE_STYLE_FILL_AREA ( #71534 ) ; +#48 = VECTOR ( 'NONE', #15017, 1000.000000000000000 ) ; +#49 = ORIENTED_EDGE ( 'NONE', *, *, #24117, .F. ) ; +#50 = EDGE_CURVE ( 'NONE', #27451, #89863, #22827, .T. ) ; +#51 = EDGE_LOOP ( 'NONE', ( #9621, #39596, #61903, #77433 ) ) ; +#52 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53 = ORIENTED_EDGE ( 'NONE', *, *, #34669, .F. ) ; +#54 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55 = VECTOR ( 'NONE', #72202, 1000.000000000000000 ) ; +#56 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58 = ORIENTED_EDGE ( 'NONE', *, *, #48320, .F. ) ; +#57 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.000000000000000000 ) ) ; +#59 = VECTOR ( 'NONE', #109, 1000.000000000000000 ) ; +#60 = ADVANCED_FACE ( 'NONE', ( #44269 ), #29468, .F. ) ; +#61 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 5.373192999999999664, 0.8991599999999999593 ) ) ; +#62 = SURFACE_STYLE_USAGE ( .BOTH. , #53203 ) ; +#63 = LINE ( 'NONE', #40923, #85660 ) ; +#64 = SURFACE_STYLE_FILL_AREA ( #53701 ) ; +#65 = EDGE_LOOP ( 'NONE', ( #12885, #36601, #20001, #30689 ) ) ; +#66 = SURFACE_STYLE_USAGE ( .BOTH. , #86352 ) ; +#67 = SURFACE_SIDE_STYLE ('',( #54212 ) ) ; +#68 = ORIENTED_EDGE ( 'NONE', *, *, #15583, .F. ) ; +#69 = EDGE_CURVE ( 'NONE', #21592, #97502, #95071, .T. ) ; +#70 = LINE ( 'NONE', #38890, #88911 ) ; +#71 = FILL_AREA_STYLE ('',( #46523 ) ) ; +#72 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73 = EDGE_LOOP ( 'NONE', ( #6544, #82933, #80333, #34998 ) ) ; +#74 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#76 = EDGE_CURVE ( 'NONE', #18215, #95021, #30433, .T. ) ; +#78 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#77 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.099999999999999867, 0.8299999999999999600 ) ) ; +#81 = EDGE_CURVE ( 'NONE', #72474, #38363, #76422, .T. ) ; +#80 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#82 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 7.346839692639300209E-32 ) ) ; +#83 = ORIENTED_EDGE ( 'NONE', *, *, #45025, .F. ) ; +#84 = AXIS2_PLACEMENT_3D ( 'NONE', #57849, #27695, #58860 ) ; +#85 = FACE_OUTER_BOUND ( 'NONE', #6668, .T. ) ; +#86 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#89 = CARTESIAN_POINT ( 'NONE', ( 1.568874050374579943, -1.341601374162270099, 0.8299999999999999600 ) ) ; +#88 = SURFACE_SIDE_STYLE ('',( #94520 ) ) ; +#90 = FACE_OUTER_BOUND ( 'NONE', #36089, .T. ) ; +#91 = PRODUCT_DEFINITION ( 'δ֪', '', #91007, #47355 ) ; +#92 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#93 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94 = SURFACE_STYLE_FILL_AREA ( #30724 ) ; +#95 = VERTEX_POINT ( 'NONE', #92236 ) ; +#96 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97 = AXIS2_PLACEMENT_3D ( 'NONE', #27874, #90638, #68632 ) ; +#98 = ORIENTED_EDGE ( 'NONE', *, *, #79985, .T. ) ; +#99 = AXIS2_PLACEMENT_3D ( 'NONE', #59583, #68668, #27914 ) ; +#100 = EDGE_CURVE ( 'NONE', #100135, #69445, #37283, .T. ) ; +#101 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#102 = LINE ( 'NONE', #15910, #68629 ) ; +#103 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#104 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#105 = AXIS2_PLACEMENT_3D ( 'NONE', #78839, #47187, #14987 ) ; +#106 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#107 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#108 = ORIENTED_EDGE ( 'NONE', *, *, #54255, .T. ) ; +#109 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#110 = ADVANCED_FACE ( 'NONE', ( #6427 ), #6897, .T. ) ; +#111 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#112 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#113 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, 3.500000000000000444, 0.000000000000000000 ) ) ; +#114 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.500000000000000000, 0.1829999999999999682 ) ) ; +#115 = CARTESIAN_POINT ( 'NONE', ( 2.676179938779915002, -3.099999999999960121, 0.000000000000000000 ) ) ; +#116 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853448918, 0.2349715759269650484, 0.8100000000000000533 ) ) ; +#117 = ADVANCED_FACE ( 'NONE', ( #70777 ), #50243, .T. ) ; +#118 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#119 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#120 = CARTESIAN_POINT ( 'NONE', ( -0.07453434150941770642, -0.9021709523542820186, 0.8299999999999999600 ) ) ; +#121 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#122 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74781, 'distance_accuracy_value', 'NONE'); +#123 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#124 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#125 = ORIENTED_EDGE ( 'NONE', *, *, #63168, .F. ) ; +#126 = LINE ( 'NONE', #6224, #69276 ) ; +#127 = EDGE_CURVE ( 'NONE', #72506, #30669, #94242, .T. ) ; +#128 = ORIENTED_EDGE ( 'NONE', *, *, #36056, .T. ) ; +#129 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#131 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20957, 'distance_accuracy_value', 'NONE'); +#130 = VECTOR ( 'NONE', #31973, 1000.000000000000114 ) ; +#132 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39119, 'distance_accuracy_value', 'NONE'); +#133 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#134 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#135 = PRESENTATION_STYLE_ASSIGNMENT (( #63477 ) ) ; +#136 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#137 = LINE ( 'NONE', #56329, #65142 ) ; +#138 = FACE_OUTER_BOUND ( 'NONE', #81861, .T. ) ; +#139 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8648700000000000276 ) ) ; +#140 = PLANE ( 'NONE', #62379 ) ; +#141 = VERTEX_POINT ( 'NONE', #24356 ) ; +#142 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#143 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#144 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64030, 'distance_accuracy_value', 'NONE'); +#145 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#146 = VERTEX_POINT ( 'NONE', #16629 ) ; +#147 = SURFACE_STYLE_USAGE ( .BOTH. , #70086 ) ; +#148 = CARTESIAN_POINT ( 'NONE', ( 0.4333333333333316828, 3.500000000000000000, 0.000000000000000000 ) ) ; +#149 = STYLED_ITEM ( 'NONE', ( #61570 ), #51511 ) ; +#150 = ORIENTED_EDGE ( 'NONE', *, *, #48382, .T. ) ; +#152 = EDGE_CURVE ( 'NONE', #39553, #48127, #47811, .T. ) ; +#151 = STYLED_ITEM ( 'NONE', ( #55600 ), #46180 ) ; +#153 = ADVANCED_FACE ( 'NONE', ( #34406 ), #57910, .T. ) ; +#154 = PRESENTATION_STYLE_ASSIGNMENT (( #58486 ) ) ; +#155 = LINE ( 'NONE', #62987, #96700 ) ; +#156 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#157 = LINE ( 'NONE', #94053, #80525 ) ; +#158 = ORIENTED_EDGE ( 'NONE', *, *, #58685, .T. ) ; +#159 = VECTOR ( 'NONE', #69966, 1000.000000000000000 ) ; +#160 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#161 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#162 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#163 = CARTESIAN_POINT ( 'NONE', ( 1.418698861684009938, -1.069424818316000003, 0.8299999999999998490 ) ) ; +#164 = ADVANCED_FACE ( 'NONE', ( #54482 ), #13718, .F. ) ; +#165 = ORIENTED_EDGE ( 'NONE', *, *, #88937, .F. ) ; +#166 = ADVANCED_FACE ( 'NONE', ( #91010 ), #97623, .T. ) ; +#167 = PRESENTATION_STYLE_ASSIGNMENT (( #53800 ) ) ; +#168 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44188 ), #93057 ) ; +#169 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57354 ) ) ; +#170 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#171 = SURFACE_STYLE_FILL_AREA ( #100626 ) ; +#172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#173 = ORIENTED_EDGE ( 'NONE', *, *, #28742, .T. ) ; +#174 = EDGE_CURVE ( 'NONE', #66746, #96516, #76185, .T. ) ; +#175 = ORIENTED_EDGE ( 'NONE', *, *, #47003, .F. ) ; +#176 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #49458 ) ; +#177 = ORIENTED_EDGE ( 'NONE', *, *, #25982, .F. ) ; +#178 = VECTOR ( 'NONE', #66635, 1000.000000000000000 ) ; +#179 = ORIENTED_EDGE ( 'NONE', *, *, #7809, .T. ) ; +#181 = ORIENTED_EDGE ( 'NONE', *, *, #27291, .T. ) ; +#180 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8648700000000000276 ) ) ; +#182 = VECTOR ( 'NONE', #69238, 1000.000000000000000 ) ; +#183 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55693 ), #76871 ) ; +#184 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#186 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#185 = CARTESIAN_POINT ( 'NONE', ( -0.7175359621965019530, 1.464383040805290026, 0.8100000000000000533 ) ) ; +#187 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#188 = VERTEX_POINT ( 'NONE', #84353 ) ; +#189 = PRESENTATION_STYLE_ASSIGNMENT (( #100646 ) ) ; +#190 = ORIENTED_EDGE ( 'NONE', *, *, #94261, .F. ) ; +#191 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31108 ), #53993 ) ; +#192 = EDGE_CURVE ( 'NONE', #77757, #57013, #29105, .T. ) ; +#193 = DIRECTION ( 'NONE', ( -0.9312650831180608879, 0.000000000000000000, 0.3643423458302799678 ) ) ; +#194 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81823, #72625, #57337, #80306 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#195 = EDGE_LOOP ( 'NONE', ( #4427, #84560, #65663, #26970 ) ) ; +#196 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13175 ), #52410 ) ; +#197 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59462 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4162, #81304, #36319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#198 = SURFACE_STYLE_USAGE ( .BOTH. , #79338 ) ; +#199 = ORIENTED_EDGE ( 'NONE', *, *, #93629, .T. ) ; +#200 = EDGE_CURVE ( 'NONE', #28703, #10613, #62397, .T. ) ; +#202 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#201 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#203 = AXIS2_PLACEMENT_3D ( 'NONE', #95024, #64928, #26142 ) ; +#204 = PRESENTATION_STYLE_ASSIGNMENT (( #6772 ) ) ; +#205 = AXIS2_PLACEMENT_3D ( 'NONE', #3460, #41751, #41262 ) ; +#207 = EDGE_CURVE ( 'NONE', #26348, #61609, #45501, .T. ) ; +#206 = DIRECTION ( 'NONE', ( -1.355252715606877091E-16, -3.252606517456505019E-15, -1.000000000000000000 ) ) ; +#208 = VECTOR ( 'NONE', #1593, 1000.000000000000000 ) ; +#209 = CARTESIAN_POINT ( 'NONE', ( 0.2157961956640810364, -1.329502282602879948, 0.8299999999999982947 ) ) ; +#210 = VERTEX_POINT ( 'NONE', #37896 ) ; +#211 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#212 = VERTEX_POINT ( 'NONE', #37414 ) ; +#213 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#214 = FILL_AREA_STYLE ('',( #55878 ) ) ; +#215 = LINE ( 'NONE', #24757, #34218 ) ; +#216 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30246, 'distance_accuracy_value', 'NONE'); +#217 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#218 = FACE_BOUND ( 'NONE', #27086, .T. ) ; +#219 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81822 ), #88293 ) ; +#220 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#221 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#222 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8648700000000000276 ) ) ; +#223 = ORIENTED_EDGE ( 'NONE', *, *, #88082, .T. ) ; +#224 = CARTESIAN_POINT ( 'NONE', ( -1.038552480745770001, -1.181578794826660284, 0.8300000000000002931 ) ) ; +#225 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#226 = EDGE_CURVE ( 'NONE', #40171, #9565, #46003, .T. ) ; +#227 = SURFACE_STYLE_USAGE ( .BOTH. , #89158 ) ; +#228 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#229 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93119 ), #39367 ) ; +#230 = CARTESIAN_POINT ( 'NONE', ( -1.275112219867899910, -1.401744930657430110, 0.8299999999999998490 ) ) ; +#231 = SURFACE_STYLE_FILL_AREA ( #78854 ) ; +#232 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#233 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#234 = ORIENTED_EDGE ( 'NONE', *, *, #97440, .T. ) ; +#235 = ADVANCED_FACE ( 'NONE', ( #30203 ), #23084, .T. ) ; +#236 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#237 = SURFACE_SIDE_STYLE ('',( #48753 ) ) ; +#238 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#239 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 9.350000000000001421, -1.016439536705160407E-17 ) ) ; +#240 = VECTOR ( 'NONE', #40441, 1000.000000000000000 ) ; +#241 = VECTOR ( 'NONE', #60853, 1000.000000000000000 ) ; +#242 = LINE ( 'NONE', #23749, #45228 ) ; +#243 = FILL_AREA_STYLE_COLOUR ( '', #54643 ) ; +#244 = EDGE_CURVE ( 'NONE', #45850, #84241, #38900, .T. ) ; +#245 = FACE_OUTER_BOUND ( 'NONE', #90442, .T. ) ; +#246 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#247 = STYLED_ITEM ( 'NONE', ( #60648 ), #86715 ) ; +#248 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#249 = STYLED_ITEM ( 'NONE', ( #12630 ), #95768 ) ; +#250 = PRESENTATION_STYLE_ASSIGNMENT (( #16056 ) ) ; +#251 = PLANE ( 'NONE', #37055 ) ; +#252 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#253 = CARTESIAN_POINT ( 'NONE', ( -0.03713474025974040221, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#254 = FILL_AREA_STYLE_COLOUR ( '', #17621 ) ; +#255 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#256 = EDGE_CURVE ( 'NONE', #66277, #90226, #35662, .T. ) ; +#258 = VERTEX_POINT ( 'NONE', #83857 ) ; +#257 = STYLED_ITEM ( 'NONE', ( #83247 ), #58429 ) ; +#259 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77233, 'distance_accuracy_value', 'NONE'); +#260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11552 ), #5113 ) ; +#261 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#262 = FACE_OUTER_BOUND ( 'NONE', #81977, .T. ) ; +#263 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, 0.7999999999999999334 ) ) ; +#264 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#265 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#266 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#268 = ADVANCED_FACE ( 'NONE', ( #45014 ), #68512, .T. ) ; +#267 = FACE_OUTER_BOUND ( 'NONE', #45377, .T. ) ; +#269 = CARTESIAN_POINT ( 'NONE', ( -1.038552480745770001, -1.181578794826660284, 0.8299999999999999600 ) ) ; +#270 = VERTEX_POINT ( 'NONE', #64899 ) ; +#271 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94591, 'distance_accuracy_value', 'NONE'); +#272 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#273 = ORIENTED_EDGE ( 'NONE', *, *, #43901, .T. ) ; +#274 = EDGE_CURVE ( 'NONE', #25062, #13157, #67061, .T. ) ; +#275 = EDGE_CURVE ( 'NONE', #46344, #93048, #26117, .T. ) ; +#276 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#277 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41060 ) ) ; +#278 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#279 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#280 = SURFACE_STYLE_FILL_AREA ( #70217 ) ; +#281 = ORIENTED_EDGE ( 'NONE', *, *, #96924, .F. ) ; +#282 = EDGE_CURVE ( 'NONE', #55363, #52681, #55744, .T. ) ; +#283 = EDGE_CURVE ( 'NONE', #56085, #37922, #33263, .T. ) ; +#284 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3323, 'distance_accuracy_value', 'NONE'); +#285 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.000000000000000000, 0.4500000000000000666 ) ) ; +#286 = AXIS2_PLACEMENT_3D ( 'NONE', #10462, #58589, #80048 ) ; +#287 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#288 = ORIENTED_EDGE ( 'NONE', *, *, #6337, .F. ) ; +#289 = EDGE_CURVE ( 'NONE', #79030, #52330, #48597, .T. ) ; +#290 = LINE ( 'NONE', #23801, #79817 ) ; +#291 = FILL_AREA_STYLE ('',( #46737 ) ) ; +#292 = ORIENTED_EDGE ( 'NONE', *, *, #8887, .T. ) ; +#294 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#293 = STYLED_ITEM ( 'NONE', ( #81913 ), #51987 ) ; +#295 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#296 = EDGE_CURVE ( 'NONE', #55609, #30976, #19399, .T. ) ; +#297 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#298 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47539 ) ) ; +#299 = VERTEX_POINT ( 'NONE', #18413 ) ; +#300 = SURFACE_SIDE_STYLE ('',( #69733 ) ) ; +#301 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#302 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#303 = ORIENTED_EDGE ( 'NONE', *, *, #36211, .F. ) ; +#304 = LINE ( 'NONE', #7890, #41788 ) ; +#305 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#306 = SURFACE_SIDE_STYLE ('',( #85580 ) ) ; +#307 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36204 ), #67149 ) ; +#308 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#309 = PLANE ( 'NONE', #77536 ) ; +#310 = ORIENTED_EDGE ( 'NONE', *, *, #13555, .T. ) ; +#311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#312 = VERTEX_POINT ( 'NONE', #16890 ) ; +#313 = EDGE_LOOP ( 'NONE', ( #81512, #692, #22931, #79578 ) ) ; +#314 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#315 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65551 ), #83498 ) ; +#316 = AXIS2_PLACEMENT_3D ( 'NONE', #42353, #9595, #57186 ) ; +#317 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68808 ) ) ; +#318 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#319 = SURFACE_SIDE_STYLE ('',( #62648 ) ) ; +#321 = ADVANCED_FACE ( 'NONE', ( #63903 ), #24103, .F. ) ; +#320 = SURFACE_STYLE_FILL_AREA ( #30971 ) ; +#322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15600, #39115, #86071 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#323 = ORIENTED_EDGE ( 'NONE', *, *, #99480, .T. ) ; +#324 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65489 ) ) ; +#325 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#326 = FACE_OUTER_BOUND ( 'NONE', #100507, .T. ) ; +#327 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#328 = STYLED_ITEM ( 'NONE', ( #26339 ), #11028 ) ; +#329 = VERTEX_POINT ( 'NONE', #75570 ) ; +#330 = PRESENTATION_STYLE_ASSIGNMENT (( #93722 ) ) ; +#331 = ORIENTED_EDGE ( 'NONE', *, *, #87890, .F. ) ; +#332 = ORIENTED_EDGE ( 'NONE', *, *, #4888, .F. ) ; +#333 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#335 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.000000000000000000 ) ) ; +#334 = SURFACE_STYLE_FILL_AREA ( #39145 ) ; +#336 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#337 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.000000000000000000, -13.54999999999999893 ) ) ; +#338 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7206 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30009, #16186, #87182 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#339 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#340 = FACE_OUTER_BOUND ( 'NONE', #5886, .T. ) ; +#341 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#342 = ORIENTED_EDGE ( 'NONE', *, *, #27804, .T. ) ; +#343 = FILL_AREA_STYLE ('',( #100808 ) ) ; +#344 = EDGE_CURVE ( 'NONE', #9533, #90134, #90896, .T. ) ; +#345 = PRESENTATION_STYLE_ASSIGNMENT (( #32015 ) ) ; +#346 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#347 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#348 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#349 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#350 = ORIENTED_EDGE ( 'NONE', *, *, #72322, .F. ) ; +#351 = EDGE_CURVE ( 'NONE', #98768, #39075, #13264, .T. ) ; +#352 = PLANE ( 'NONE', #100873 ) ; +#353 = FACE_OUTER_BOUND ( 'NONE', #89390, .T. ) ; +#354 = AXIS2_PLACEMENT_3D ( 'NONE', #33427, #40582, #95148 ) ; +#355 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3655 ), #80277 ) ; +#356 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#357 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43125, 'distance_accuracy_value', 'NONE'); +#358 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.500000000000000444, 0.000000000000000000 ) ) ; +#359 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85130 ), #67206 ) ; +#360 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#361 = LINE ( 'NONE', #78486, #29029 ) ; +#362 = LINE ( 'NONE', #45799, #68336 ) ; +#363 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#364 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47685 ), #13340 ) ; +#366 = AXIS2_PLACEMENT_3D ( 'NONE', #2579, #10637, #72509 ) ; +#365 = LINE ( 'NONE', #63208, #37203 ) ; +#367 = EDGE_CURVE ( 'NONE', #56095, #66284, #31615, .T. ) ; +#368 = LINE ( 'NONE', #56565, #29321 ) ; +#369 = SURFACE_STYLE_USAGE ( .BOTH. , #33047 ) ; +#370 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63576, #71714, #87534 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#371 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #31915, 'design' ) ; +#372 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.000000000000000000, 0.000000000000000000 ) ) ; +#374 = EDGE_CURVE ( 'NONE', #4574, #48032, #81257, .T. ) ; +#373 = FILL_AREA_STYLE ('',( #69278 ) ) ; +#375 = PRESENTATION_STYLE_ASSIGNMENT (( #1913 ) ) ; +#376 = ORIENTED_EDGE ( 'NONE', *, *, #15790, .F. ) ; +#377 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1458578643762690752 ) ) ; +#378 = FILL_AREA_STYLE ('',( #87677 ) ) ; +#379 = LINE ( 'NONE', #64206, #64012 ) ; +#380 = CIRCLE ( 'NONE', #72130, 0.09999999999999999167 ) ; +#381 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95494, 'distance_accuracy_value', 'NONE'); +#382 = AXIS2_PLACEMENT_3D ( 'NONE', #2715, #25224, #41520 ) ; +#383 = CARTESIAN_POINT ( 'NONE', ( -3.200000000000000178, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#384 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.05000000000000000278, 0.2100000000000000200 ) ) ; +#385 = CARTESIAN_POINT ( 'NONE', ( 1.152480747614542889, -1.141426888289828190, 0.8099999999999010214 ) ) ; +#386 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29326 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73064, #57780, #48594 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#388 = EDGE_CURVE ( 'NONE', #46032, #93343, #80278, .T. ) ; +#387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46209 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81772, #11700, #19463 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#389 = AXIS2_PLACEMENT_3D ( 'NONE', #75738, #30256, #136 ) ; +#390 = ADVANCED_FACE ( 'NONE', ( #82734 ), #12712, .T. ) ; +#391 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18228 ) ) ; +#392 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#393 = EDGE_LOOP ( 'NONE', ( #24475, #24855, #28412, #80129 ) ) ; +#394 = LINE ( 'NONE', #37226, #83970 ) ; +#395 = EDGE_CURVE ( 'NONE', #89230, #41748, #43917, .T. ) ; +#396 = VECTOR ( 'NONE', #69395, 999.9999999999998863 ) ; +#397 = CARTESIAN_POINT ( 'NONE', ( 1.823253843827010057, -1.327673353236110021, 0.8299999999999994049 ) ) ; +#398 = EDGE_CURVE ( 'NONE', #84082, #61165, #90379, .T. ) ; +#399 = LINE ( 'NONE', #54560, #3114 ) ; +#400 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19086, 'distance_accuracy_value', 'NONE'); +#401 = FILL_AREA_STYLE_COLOUR ( '', #60821 ) ; +#402 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99707 ) ) ; +#403 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92208, 'distance_accuracy_value', 'NONE'); +#404 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#405 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44414 ) ) ; +#406 = VERTEX_POINT ( 'NONE', #98463 ) ; +#407 = ORIENTED_EDGE ( 'NONE', *, *, #57494, .F. ) ; +#408 = ADVANCED_FACE ( 'NONE', ( #43421 ), #74581, .T. ) ; +#409 = LINE ( 'NONE', #39213, #99172 ) ; +#410 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76731 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72354, #41245, #12507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#411 = ORIENTED_EDGE ( 'NONE', *, *, #76114, .F. ) ; +#412 = LINE ( 'NONE', #33084, #72192 ) ; +#413 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#414 = EDGE_CURVE ( 'NONE', #19280, #59960, #6055, .T. ) ; +#415 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7191, 'distance_accuracy_value', 'NONE'); +#416 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#417 = VECTOR ( 'NONE', #75143, 1000.000000000000000 ) ; +#418 = LINE ( 'NONE', #37247, #83430 ) ; +#420 = ORIENTED_EDGE ( 'NONE', *, *, #61109, .T. ) ; +#419 = EDGE_LOOP ( 'NONE', ( #38521, #96735, #27772, #11148, #12689, #1046, #20535, #95678 ) ) ; +#421 = STYLED_ITEM ( 'NONE', ( #52595 ), #70598 ) ; +#422 = ORIENTED_EDGE ( 'NONE', *, *, #16568, .F. ) ; +#424 = FILL_AREA_STYLE ('',( #100877 ) ) ; +#423 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8648700000000000276 ) ) ; +#425 = ORIENTED_EDGE ( 'NONE', *, *, #100472, .T. ) ; +#426 = VECTOR ( 'NONE', #3180, 1000.000000000000000 ) ; +#427 = SURFACE_STYLE_FILL_AREA ( #55100 ) ; +#428 = SURFACE_STYLE_FILL_AREA ( #15732 ) ; +#429 = VECTOR ( 'NONE', #23115, 1000.000000000000000 ) ; +#430 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#431 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68847 ), #57551 ) ; +#432 = SURFACE_STYLE_USAGE ( .BOTH. , #34009 ) ; +#433 = ORIENTED_EDGE ( 'NONE', *, *, #35249, .T. ) ; +#434 = FILL_AREA_STYLE_COLOUR ( '', #74765 ) ; +#435 = VECTOR ( 'NONE', #86729, 1000.000000000000000 ) ; +#436 = VERTEX_POINT ( 'NONE', #67878 ) ; +#437 = ORIENTED_EDGE ( 'NONE', *, *, #42837, .F. ) ; +#438 = FILL_AREA_STYLE_COLOUR ( '', #59173 ) ; +#439 = FILL_AREA_STYLE_COLOUR ( '', #91789 ) ; +#440 = SURFACE_SIDE_STYLE ('',( #7017 ) ) ; +#441 = STYLED_ITEM ( 'NONE', ( #56524 ), #75781 ) ; +#442 = LINE ( 'NONE', #95359, #61943 ) ; +#443 = ORIENTED_EDGE ( 'NONE', *, *, #33886, .T. ) ; +#444 = DIRECTION ( 'NONE', ( -0.7071045084557425753, 0.7071090539100477468, 0.000000000000000000 ) ) ; +#445 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#446 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#447 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 2.143355994988570127E-63 ) ) ; +#448 = AXIS2_PLACEMENT_3D ( 'NONE', #42952, #34825, #65954 ) ; +#449 = VERTEX_POINT ( 'NONE', #60775 ) ; +#451 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 3.393295000000000172, 0.8648700000000000276 ) ) ; +#450 = SURFACE_STYLE_FILL_AREA ( #40293 ) ; +#452 = ORIENTED_EDGE ( 'NONE', *, *, #71095, .F. ) ; +#453 = EDGE_CURVE ( 'NONE', #99033, #92204, #66871, .T. ) ; +#454 = VERTEX_POINT ( 'NONE', #45887 ) ; +#455 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.9000000000000001332, -0.02000000000003770290 ) ) ; +#456 = LINE ( 'NONE', #17283, #80669 ) ; +#457 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83906 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79049, #87705, #94331 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#458 = VECTOR ( 'NONE', #47702, 1000.000000000000000 ) ; +#459 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8299999999999999600 ) ) ; +#460 = SURFACE_STYLE_USAGE ( .BOTH. , #33658 ) ; +#461 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100460 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44457, #74638, #36838 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#462 = FACE_OUTER_BOUND ( 'NONE', #95370, .T. ) ; +#463 = EDGE_LOOP ( 'NONE', ( #80379, #7863, #49010, #64624, #20289, #88141 ) ) ; +#464 = CARTESIAN_POINT ( 'NONE', ( 0.4623821970225030498, -1.113520705134940059, 0.8100000000000000533 ) ) ; +#465 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#466 = VERTEX_POINT ( 'NONE', #62277 ) ; +#467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33071 ), #70583 ) ; +#468 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#469 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999929778, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#470 = AXIS2_PLACEMENT_3D ( 'NONE', #63194, #63687, #70307 ) ; +#471 = SURFACE_SIDE_STYLE ('',( #40316 ) ) ; +#472 = FILL_AREA_STYLE_COLOUR ( '', #74156 ) ; +#473 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57599 ) ) ; +#474 = PRESENTATION_STYLE_ASSIGNMENT (( #8550 ) ) ; +#476 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#475 = SURFACE_SIDE_STYLE ('',( #1507 ) ) ; +#477 = CARTESIAN_POINT ( 'NONE', ( 1.799895807589950048, -1.058723197808659977, 0.8100000000000000533 ) ) ; +#478 = LINE ( 'NONE', #93862, #63123 ) ; +#479 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27279, 'distance_accuracy_value', 'NONE'); +#480 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992895, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#482 = EDGE_CURVE ( 'NONE', #19992, #51695, #38771, .T. ) ; +#481 = SURFACE_SIDE_STYLE ('',( #22985 ) ) ; +#483 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#484 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#485 = AXIS2_PLACEMENT_3D ( 'NONE', #5882, #37099, #29419 ) ; +#486 = SURFACE_STYLE_USAGE ( .BOTH. , #63811 ) ; +#487 = LINE ( 'NONE', #8061, #23841 ) ; +#488 = FACE_OUTER_BOUND ( 'NONE', #82953, .T. ) ; +#489 = LINE ( 'NONE', #84753, #12634 ) ; +#490 = PLANE ( 'NONE', #29363 ) ; +#491 = LINE ( 'NONE', #56680, #25809 ) ; +#492 = PRESENTATION_STYLE_ASSIGNMENT (( #23498 ) ) ; +#493 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#494 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73006, 'distance_accuracy_value', 'NONE'); +#495 = EDGE_LOOP ( 'NONE', ( #81094, #43013, #17679, #17516 ) ) ; +#496 = CARTESIAN_POINT ( 'NONE', ( 1.655237363055763966, -1.164073081312990476, 0.8100000000000000533 ) ) ; +#497 = EDGE_CURVE ( 'NONE', #9040, #64000, #99673, .T. ) ; +#498 = ORIENTED_EDGE ( 'NONE', *, *, #47223, .T. ) ; +#499 = FACE_OUTER_BOUND ( 'NONE', #75072, .T. ) ; +#500 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000001235, -0.2349999999999999867 ) ) ; +#501 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#503 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8576 ), #6975 ) ; +#504 = LINE ( 'NONE', #86284, #58093 ) ; +#505 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8648700000000000276 ) ) ; +#506 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#507 = STYLED_ITEM ( 'NONE', ( #33851 ), #26146 ) ; +#508 = ORIENTED_EDGE ( 'NONE', *, *, #26234, .F. ) ; +#509 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98264 ) ) ; +#510 = EDGE_LOOP ( 'NONE', ( #3467, #23701, #79705, #27227 ) ) ; +#511 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#512 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#513 = FILL_AREA_STYLE ('',( #8589 ) ) ; +#514 = ADVANCED_FACE ( 'NONE', ( #7533 ), #69895, .F. ) ; +#515 = PLANE ( 'NONE', #17191 ) ; +#516 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#517 = SURFACE_SIDE_STYLE ('',( #78149 ) ) ; +#518 = VECTOR ( 'NONE', #91186, 1000.000000000000000 ) ; +#519 = ORIENTED_EDGE ( 'NONE', *, *, #94039, .T. ) ; +#520 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#521 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#522 = PRESENTATION_STYLE_ASSIGNMENT (( #46992 ) ) ; +#523 = ORIENTED_EDGE ( 'NONE', *, *, #41580, .T. ) ; +#524 = STYLED_ITEM ( 'NONE', ( #62805 ), #19087 ) ; +#525 = VECTOR ( 'NONE', #44796, 1000.000000000000114 ) ; +#526 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#527 = ORIENTED_EDGE ( 'NONE', *, *, #81460, .T. ) ; +#528 = SURFACE_SIDE_STYLE ('',( #86824 ) ) ; +#529 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1957 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87139, #95254, #2382 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#530 = CARTESIAN_POINT ( 'NONE', ( 1.194650275651319982, -1.445196667902379994, 0.8100000000000000533 ) ) ; +#531 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#532 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8611 ) ) ; +#533 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.91999999999999993 ) ) ; +#534 = EDGE_CURVE ( 'NONE', #25848, #78817, #71433, .T. ) ; +#535 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#536 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#537 = FILL_AREA_STYLE_COLOUR ( '', #41026 ) ; +#539 = ORIENTED_EDGE ( 'NONE', *, *, #100099, .T. ) ; +#538 = VERTEX_POINT ( 'NONE', #32641 ) ; +#540 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21686 ), #11829 ) ; +#541 = AXIS2_PLACEMENT_3D ( 'NONE', #54906, #94662, #39556 ) ; +#542 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#543 = ORIENTED_EDGE ( 'NONE', *, *, #74172, .F. ) ; +#544 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56976 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10031, #87225, #18770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#546 = PLANE ( 'NONE', #93566 ) ; +#547 = EDGE_LOOP ( 'NONE', ( #44937, #57363, #16310, #54518 ) ) ; +#548 = EDGE_LOOP ( 'NONE', ( #72144, #47940, #24178, #19105 ) ) ; +#549 = PLANE ( 'NONE', #70794 ) ; +#550 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#551 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#552 = ORIENTED_EDGE ( 'NONE', *, *, #1377, .T. ) ; +#553 = ORIENTED_EDGE ( 'NONE', *, *, #65772, .T. ) ; +#554 = ORIENTED_EDGE ( 'NONE', *, *, #59359, .F. ) ; +#555 = LINE ( 'NONE', #39365, #24839 ) ; +#556 = EDGE_CURVE ( 'NONE', #91942, #86671, #9655, .T. ) ; +#557 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59224 ) ) ; +#559 = EDGE_LOOP ( 'NONE', ( #61527, #99909, #98506, #64949 ) ) ; +#558 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#560 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#561 = PRESENTATION_STYLE_ASSIGNMENT (( #100044 ) ) ; +#562 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#563 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#564 = ORIENTED_EDGE ( 'NONE', *, *, #99786, .F. ) ; +#565 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#566 = SURFACE_STYLE_USAGE ( .BOTH. , #55246 ) ; +#567 = ORIENTED_EDGE ( 'NONE', *, *, #3969, .F. ) ; +#568 = EDGE_CURVE ( 'NONE', #70963, #67401, #95893, .T. ) ; +#569 = PRESENTATION_STYLE_ASSIGNMENT (( #39377 ) ) ; +#570 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#571 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73770 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27263, #18034, #3757 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#572 = CARTESIAN_POINT ( 'NONE', ( -0.7486880133853439645, 1.376284075926970107, 0.8299999999999999600 ) ) ; +#573 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42936 ) ) ; +#574 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#576 = ORIENTED_EDGE ( 'NONE', *, *, #4382, .F. ) ; +#575 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#577 = SURFACE_STYLE_USAGE ( .BOTH. , #26116 ) ; +#578 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#580 = PLANE ( 'NONE', #64537 ) ; +#579 = LINE ( 'NONE', #95503, #43180 ) ; +#581 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#582 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#584 = CARTESIAN_POINT ( 'NONE', ( 1.814236996624309928, -1.283680827045210027, 0.8100000000000006084 ) ) ; +#583 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #50456 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#585 = ORIENTED_EDGE ( 'NONE', *, *, #80173, .F. ) ; +#586 = PRESENTATION_STYLE_ASSIGNMENT (( #85866 ) ) ; +#587 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#588 = STYLED_ITEM ( 'NONE', ( #25031 ), #19653 ) ; +#589 = FILL_AREA_STYLE ('',( #22069 ) ) ; +#591 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#590 = SURFACE_STYLE_USAGE ( .BOTH. , #88 ) ; +#593 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46145 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93757, #18182, #33038 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#592 = FILL_AREA_STYLE ('',( #39399 ) ) ; +#594 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16907 ), #85363 ) ; +#596 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#597 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#598 = LINE ( 'NONE', #22586, #88256 ) ; +#599 = ORIENTED_EDGE ( 'NONE', *, *, #28426, .T. ) ; +#600 = EDGE_CURVE ( 'NONE', #28287, #13261, #22755, .T. ) ; +#601 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76570, #37787, #92382, #22451 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#602 = FILL_AREA_STYLE_COLOUR ( '', #82444 ) ; +#603 = STYLED_ITEM ( 'NONE', ( #98412 ), #37322 ) ; +#604 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32168 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99632, #45091, #98169 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#605 = VERTEX_POINT ( 'NONE', #47948 ) ; +#606 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#608 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#607 = SURFACE_STYLE_USAGE ( .BOTH. , #55279 ) ; +#609 = FILL_AREA_STYLE ('',( #70559 ) ) ; +#610 = AXIS2_PLACEMENT_3D ( 'NONE', #75238, #6209, #29744 ) ; +#611 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#612 = STYLED_ITEM ( 'NONE', ( #53832 ), #11875 ) ; +#613 = FILL_AREA_STYLE_COLOUR ( '', #72301 ) ; +#614 = ORIENTED_EDGE ( 'NONE', *, *, #85564, .T. ) ; +#615 = CARTESIAN_POINT ( 'NONE', ( 8.093172875124999166, 4.142827124874999711, 0.8648700000000000276 ) ) ; +#616 = ADVANCED_FACE ( 'NONE', ( #10052 ), #982, .T. ) ; +#617 = LINE ( 'NONE', #86916, #83795 ) ; +#618 = PLANE ( 'NONE', #99053 ) ; +#619 = EDGE_CURVE ( 'NONE', #65103, #64495, #93850, .T. ) ; +#620 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#621 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959499, 0.000000000000000000 ) ) ; +#622 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#623 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33820 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63861, #18360, #79689 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#624 = SURFACE_SIDE_STYLE ('',( #70572 ) ) ; +#625 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#626 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23061, #61869, #62372 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#627 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#628 = ORIENTED_EDGE ( 'NONE', *, *, #27418, .F. ) ; +#629 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76991 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70027, #63427, #77185 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#630 = ORIENTED_EDGE ( 'NONE', *, *, #82998, .F. ) ; +#631 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#632 = PRESENTATION_STYLE_ASSIGNMENT (( #16950 ) ) ; +#633 = LINE ( 'NONE', #46591, #33257 ) ; +#634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#635 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#636 = EDGE_CURVE ( 'NONE', #19918, #74000, #9563, .T. ) ; +#637 = PLANE ( 'NONE', #57016 ) ; +#638 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#639 = FILL_AREA_STYLE ('',( #30770 ) ) ; +#640 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62631 ) ) ; +#641 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000038414, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#642 = ORIENTED_EDGE ( 'NONE', *, *, #10453, .F. ) ; +#643 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, -1.899999999999999689, 0.000000000000000000 ) ) ; +#644 = CARTESIAN_POINT ( 'NONE', ( 9.507386875125000358, 6.971254875125000083, 0.8991599999999999593 ) ) ; +#645 = ORIENTED_EDGE ( 'NONE', *, *, #81681, .T. ) ; +#646 = CARTESIAN_POINT ( 'NONE', ( 1.202821433957329544, -1.225742884720171011, 0.8099999999998477307 ) ) ; +#647 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46321 ) ) ; +#648 = AXIS2_PLACEMENT_3D ( 'NONE', #69258, #92280, #46293 ) ; +#649 = FILL_AREA_STYLE_COLOUR ( '', #21082 ) ; +#650 = ORIENTED_EDGE ( 'NONE', *, *, #15309, .T. ) ; +#651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39810 ) ) ; +#652 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44660 ) ) ; +#653 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#654 = DIRECTION ( 'NONE', ( 0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#655 = EDGE_CURVE ( 'NONE', #24202, #92656, #78569, .T. ) ; +#656 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#657 = FILL_AREA_STYLE ('',( #84424 ) ) ; +#658 = AXIS2_PLACEMENT_3D ( 'NONE', #53358, #84490, #14502 ) ; +#659 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999994671, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#660 = ORIENTED_EDGE ( 'NONE', *, *, #40559, .F. ) ; +#661 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#662 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#663 = VECTOR ( 'NONE', #26629, 1000.000000000000000 ) ; +#664 = VECTOR ( 'NONE', #72862, 1000.000000000000000 ) ; +#665 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#666 = ORIENTED_EDGE ( 'NONE', *, *, #19335, .F. ) ; +#668 = VECTOR ( 'NONE', #61433, 1000.000000000000000 ) ; +#667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93555 ), #31654 ) ; +#669 = FILL_AREA_STYLE ('',( #77265 ) ) ; +#670 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#671 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71977 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30597, #61307, #92395 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#672 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#673 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -7.346839692639300209E-32 ) ) ; +#674 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 7.565224999999999866, 0.8648700000000000276 ) ) ; +#675 = SURFACE_STYLE_USAGE ( .BOTH. , #70623 ) ; +#676 = ORIENTED_EDGE ( 'NONE', *, *, #67384, .F. ) ; +#677 = EDGE_LOOP ( 'NONE', ( #43141, #13334, #95211, #76783 ) ) ; +#678 = SURFACE_SIDE_STYLE ('',( #86974 ) ) ; +#679 = EDGE_LOOP ( 'NONE', ( #49192, #676, #29538 ) ) ; +#680 = VECTOR ( 'NONE', #75640, 1000.000000000000000 ) ; +#681 = EDGE_CURVE ( 'NONE', #50863, #28081, #86237, .T. ) ; +#682 = ORIENTED_EDGE ( 'NONE', *, *, #75507, .F. ) ; +#684 = EDGE_LOOP ( 'NONE', ( #74450, #8148, #76508, #1325 ) ) ; +#683 = LINE ( 'NONE', #180, #42762 ) ; +#685 = STYLED_ITEM ( 'NONE', ( #25730 ), #11982 ) ; +#686 = FACE_OUTER_BOUND ( 'NONE', #80659, .T. ) ; +#687 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#688 = FILL_AREA_STYLE ('',( #40013 ) ) ; +#689 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65947 ), #2333 ) ; +#690 = VERTEX_POINT ( 'NONE', #94388 ) ; +#691 = CARTESIAN_POINT ( 'NONE', ( -0.4406617557324680190, 0.3469459166020285035, 0.8100000000000000533 ) ) ; +#692 = ORIENTED_EDGE ( 'NONE', *, *, #75708, .T. ) ; +#693 = EDGE_CURVE ( 'NONE', #29072, #90840, #98439, .T. ) ; +#694 = SURFACE_STYLE_USAGE ( .BOTH. , #40543 ) ; +#695 = LINE ( 'NONE', #76287, #46380 ) ; +#696 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#697 = CARTESIAN_POINT ( 'NONE', ( -0.3870363089776986953, 0.5647286298174479802, 0.8100000000000001643 ) ) ; +#698 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8778 ), #41544 ) ; +#699 = ORIENTED_EDGE ( 'NONE', *, *, #51641, .T. ) ; +#700 = EDGE_CURVE ( 'NONE', #15191, #22507, #24502, .T. ) ; +#701 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#702 = VERTEX_POINT ( 'NONE', #42807 ) ; +#703 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#704 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#705 = SURFACE_STYLE_FILL_AREA ( #46661 ) ; +#706 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.6999999999999999556, -13.54999999999999893 ) ) ; +#707 = VECTOR ( 'NONE', #25574, 1000.000000000000000 ) ; +#708 = ORIENTED_EDGE ( 'NONE', *, *, #8172, .T. ) ; +#709 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#710 = PRESENTATION_STYLE_ASSIGNMENT (( #47182 ) ) ; +#711 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#712 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#713 = SURFACE_SIDE_STYLE ('',( #77828 ) ) ; +#715 = VECTOR ( 'NONE', #64832, 1000.000000000000114 ) ; +#714 = PLANE ( 'NONE', #91926 ) ; +#716 = VECTOR ( 'NONE', #80351, 1000.000000000000000 ) ; +#717 = EDGE_CURVE ( 'NONE', #66042, #85984, #28013, .T. ) ; +#719 = ADVANCED_FACE ( 'NONE', ( #19827 ), #81634, .T. ) ; +#718 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#720 = FACE_OUTER_BOUND ( 'NONE', #67866, .T. ) ; +#721 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#722 = CARTESIAN_POINT ( 'NONE', ( 5.646583499500048120, 9.827965500499949769, 0.8991599999999999593 ) ) ; +#723 = DIRECTION ( 'NONE', ( -0.7071067811865465735, -0.7071067811865485719, 0.000000000000000000 ) ) ; +#724 = ORIENTED_EDGE ( 'NONE', *, *, #1548, .F. ) ; +#725 = CARTESIAN_POINT ( 'NONE', ( -0.9713447595867019668, -1.214210613447320064, 0.8300000000000002931 ) ) ; +#726 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#727 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#729 = FACE_OUTER_BOUND ( 'NONE', #31936, .T. ) ; +#728 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#730 = LINE ( 'NONE', #55405, #71652 ) ; +#731 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2493, 'distance_accuracy_value', 'NONE'); +#732 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#733 = PRESENTATION_STYLE_ASSIGNMENT (( #70172 ) ) ; +#734 = VECTOR ( 'NONE', #18292, 1000.000000000000000 ) ; +#735 = AXIS2_PLACEMENT_3D ( 'NONE', #91665, #82538, #40085 ) ; +#736 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#737 = CARTESIAN_POINT ( 'NONE', ( 9.691234249749911100, 9.262280750250088346, 0.8648700000000000276 ) ) ; +#738 = SURFACE_STYLE_FILL_AREA ( #47206 ) ; +#739 = VECTOR ( 'NONE', #90938, 1000.000000000000000 ) ; +#740 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#741 = VERTEX_POINT ( 'NONE', #50502 ) ; +#742 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#743 = EDGE_CURVE ( 'NONE', #11229, #94730, #89275, .T. ) ; +#744 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#745 = ADVANCED_FACE ( 'NONE', ( #36173 ), #20824, .T. ) ; +#747 = VECTOR ( 'NONE', #18635, 1000.000000000000114 ) ; +#746 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#748 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#749 = FILL_AREA_STYLE ('',( #23747 ) ) ; +#750 = DIRECTION ( 'NONE', ( -0.7071062811868784603, 0.7071072811858630791, 0.000000000000000000 ) ) ; +#751 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.000000000000000000 ) ) ; +#752 = SURFACE_SIDE_STYLE ('',( #54398 ) ) ; +#753 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#754 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#755 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74174 ) ) ; +#756 = SURFACE_STYLE_USAGE ( .BOTH. , #28886 ) ; +#757 = CARTESIAN_POINT ( 'NONE', ( 1.067938486522060026, -1.390907012919420094, 0.8299999999999999600 ) ) ; +#758 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#759 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#760 = ORIENTED_EDGE ( 'NONE', *, *, #2001, .T. ) ; +#761 = LINE ( 'NONE', #100219, #100116 ) ; +#762 = ORIENTED_EDGE ( 'NONE', *, *, #69799, .T. ) ; +#763 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#764 = CARTESIAN_POINT ( 'NONE', ( 0.2283082038525930113, -1.316727038456209975, 0.8299999999999999600 ) ) ; +#766 = EDGE_CURVE ( 'NONE', #62005, #43664, #57669, .T. ) ; +#765 = STYLED_ITEM ( 'NONE', ( #51112 ), #12411 ) ; +#767 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#768 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#769 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#770 = CARTESIAN_POINT ( 'NONE', ( -0.9713447595867019668, -1.214210613447320064, 0.8100000000000000533 ) ) ; +#771 = ORIENTED_EDGE ( 'NONE', *, *, #89916, .F. ) ; +#772 = FACE_OUTER_BOUND ( 'NONE', #58138, .T. ) ; +#773 = EDGE_CURVE ( 'NONE', #22488, #14748, #81130, .T. ) ; +#774 = CARTESIAN_POINT ( 'NONE', ( 4.798055249750023954, 8.979437750249974926, 0.8648700000000000276 ) ) ; +#775 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#776 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#777 = VERTEX_POINT ( 'NONE', #45273 ) ; +#778 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31757 ) ) ; +#779 = ADVANCED_FACE ( 'NONE', ( #5946 ), #36672, .T. ) ; +#780 = CARTESIAN_POINT ( 'NONE', ( 0.6166666666666670293, 3.099999999999980549, 0.000000000000000000 ) ) ; +#781 = EDGE_CURVE ( 'NONE', #82829, #14472, #30989, .T. ) ; +#782 = VECTOR ( 'NONE', #16644, 1000.000000000000000 ) ; +#783 = ORIENTED_EDGE ( 'NONE', *, *, #25013, .T. ) ; +#784 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#785 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61518, 'distance_accuracy_value', 'NONE'); +#786 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#787 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82585 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7543, #79114, #32142 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#788 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544766999999999779, 0.8991599999999999593 ) ) ; +#789 = ORIENTED_EDGE ( 'NONE', *, *, #66862, .T. ) ; +#790 = VECTOR ( 'NONE', #95154, 1000.000000000000000 ) ; +#791 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#792 = ORIENTED_EDGE ( 'NONE', *, *, #97543, .F. ) ; +#793 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#794 = CARTESIAN_POINT ( 'NONE', ( 0.01835565287466199916, -1.473933850988760064, 0.8100000000000000533 ) ) ; +#795 = AXIS2_PLACEMENT_3D ( 'NONE', #92698, #13549, #93696 ) ; +#796 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8099999999999852873 ) ) ; +#797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13791 ) ) ; +#798 = VECTOR ( 'NONE', #52711, 1000.000000000000000 ) ; +#799 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #97021, #28130, #4614, #88395, #42928, #43429, #73580, #74592, #27133, #27641, #82255, #97532, #12208, #73077, #81765, #88903, #49609, #11193, #41945 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.072587340663866828E-05, 4.034341579484912276E-05, 5.898151083560916131E-05, 7.687265495570454448E-05, 9.424942554674390521E-05, 0.0001110427277989051929, 0.0001276028031437667859, 0.0001442683235908595607, 0.0001608324324584153452, 0.0001776314797122388795, 0.0001946970559930491962, 0.0002124126760051262648, 0.0002310069119530191398, 0.0002504820500737618195, 0.0002711771011231196393, 0.0002931139026064212018 ), + .UNSPECIFIED. ) ; +#800 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #78852, #64549 ), + ( #41579, #40580 ), + ( #95653, #56422 ), + ( #48744, #73231 ), + ( #50273, #71703 ), + ( #2276, #79883 ), + ( #97162, #49755 ), + ( #42582, #9831 ), + ( #25759, #96664 ), + ( #79368, #17053 ), + ( #80389, #48240 ), + ( #80900, #32905 ), + ( #1778, #41083 ), + ( #72206, #88032 ), + ( #18044, #49238 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.05889048081243219990, 0.1162601062174010019, 0.1723791748519470091, 0.2292020384589500137, 0.2867178054804920273, 0.3458061857271019779, 0.4055743739783380097, 0.4669621906862910232, 0.5942921608797639976, 0.7269913554632789765, 0.8632304667955349453, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#801 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #91976, #91629 ) ; +#802 = CARTESIAN_POINT ( 'NONE', ( 0.2546877245216000452, -1.031834659001420018, 0.8100000000000000533 ) ) ; +#803 = ADVANCED_FACE ( 'NONE', ( #62169 ), #46277, .F. ) ; +#804 = EDGE_LOOP ( 'NONE', ( #98536, #94489, #47433, #9002 ) ) ; +#805 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#807 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32644 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89064, #65562, #79913 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#806 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36515, 'distance_accuracy_value', 'NONE'); +#808 = SURFACE_STYLE_USAGE ( .BOTH. , #8893 ) ; +#809 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#810 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7223 ) ) ; +#812 = ADVANCED_FACE ( 'NONE', ( #76959 ), #44284, .T. ) ; +#813 = VECTOR ( 'NONE', #67959, 1000.000000000000000 ) ; +#814 = EDGE_LOOP ( 'NONE', ( #27487, #2674, #9280, #48824 ) ) ; +#815 = EDGE_CURVE ( 'NONE', #26462, #32195, #63175, .T. ) ; +#816 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#817 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#819 = STYLED_ITEM ( 'NONE', ( #64653 ), #27537 ) ; +#818 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95322 ) ) ; +#820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#821 = VECTOR ( 'NONE', #100702, 1000.000000000000000 ) ; +#822 = FACE_OUTER_BOUND ( 'NONE', #37744, .T. ) ; +#823 = ORIENTED_EDGE ( 'NONE', *, *, #28853, .T. ) ; +#824 = EDGE_CURVE ( 'NONE', #56416, #27582, #68117, .T. ) ; +#826 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#825 = FACE_OUTER_BOUND ( 'NONE', #78380, .T. ) ; +#827 = EDGE_LOOP ( 'NONE', ( #5003, #67970, #20263, #1977 ) ) ; +#828 = VERTEX_POINT ( 'NONE', #854 ) ; +#829 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20431 ) ) ; +#830 = FILL_AREA_STYLE ('',( #77936 ) ) ; +#831 = FACE_OUTER_BOUND ( 'NONE', #86218, .T. ) ; +#833 = EDGE_CURVE ( 'NONE', #11018, #69332, #64660, .T. ) ; +#832 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, -1.050000000000000044 ) ) ; +#834 = ORIENTED_EDGE ( 'NONE', *, *, #34855, .T. ) ; +#835 = STYLED_ITEM ( 'NONE', ( #46110 ), #3538 ) ; +#836 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#837 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36654 ), #90487 ) ; +#838 = SURFACE_STYLE_USAGE ( .BOTH. , #15622 ) ; +#839 = VERTEX_POINT ( 'NONE', #86627 ) ; +#840 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#841 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#842 = ORIENTED_EDGE ( 'NONE', *, *, #25269, .F. ) ; +#843 = ORIENTED_EDGE ( 'NONE', *, *, #70679, .T. ) ; +#844 = SURFACE_SIDE_STYLE ('',( #69227 ) ) ; +#845 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#846 = SURFACE_STYLE_USAGE ( .BOTH. , #64158 ) ; +#847 = SURFACE_STYLE_FILL_AREA ( #15632 ) ; +#848 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97057 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86330, #78180, #85312 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#849 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8099999999999785150 ) ) ; +#850 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54548 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31729, #78686, #93964 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#851 = EDGE_CURVE ( 'NONE', #60542, #25989, #47828, .T. ) ; +#853 = ADVANCED_FACE ( 'NONE', ( #8421 ), #33013, .T. ) ; +#852 = PLANE ( 'NONE', #54058 ) ; +#854 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#855 = FACE_OUTER_BOUND ( 'NONE', #35713, .T. ) ; +#856 = EDGE_LOOP ( 'NONE', ( #12119, #26321, #74644, #58463 ) ) ; +#858 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31829 ) ) ; +#857 = LINE ( 'NONE', #39663, #20240 ) ; +#859 = CARTESIAN_POINT ( 'NONE', ( -1.033269450816116208, -1.497085791687842615, 0.8099999999996221334 ) ) ; +#860 = FACE_OUTER_BOUND ( 'NONE', #56396, .T. ) ; +#861 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#862 = CIRCLE ( 'NONE', #26983, 0.1100000000000007222 ) ; +#863 = LINE ( 'NONE', #17174, #15838 ) ; +#864 = FILL_AREA_STYLE ('',( #25889 ) ) ; +#865 = VERTEX_POINT ( 'NONE', #93738 ) ; +#866 = STYLED_ITEM ( 'NONE', ( #86065 ), #49444 ) ; +#867 = FILL_AREA_STYLE ('',( #9464 ) ) ; +#868 = LINE ( 'NONE', #93752, #46059 ) ; +#869 = SURFACE_STYLE_FILL_AREA ( #86130 ) ; +#870 = VECTOR ( 'NONE', #30061, 999.9999999999998863 ) ; +#871 = EDGE_CURVE ( 'NONE', #16675, #50319, #48853, .T. ) ; +#873 = CYLINDRICAL_SURFACE ( 'NONE', #98525, 0.009999999999999998473 ) ; +#872 = AXIS2_PLACEMENT_3D ( 'NONE', #91540, #77218, #5226 ) ; +#874 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#875 = PRESENTATION_STYLE_ASSIGNMENT (( #63691 ) ) ; +#876 = PRESENTATION_STYLE_ASSIGNMENT (( #94278 ) ) ; +#877 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#878 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72359, #27426, #28425 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#879 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33564 ) ) ; +#880 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#881 = PRESENTATION_STYLE_ASSIGNMENT (( #8443 ) ) ; +#882 = FILL_AREA_STYLE_COLOUR ( '', #95581 ) ; +#883 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#884 = LINE ( 'NONE', #61684, #34450 ) ; +#885 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#886 = VECTOR ( 'NONE', #76654, 1000.000000000000000 ) ; +#887 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#888 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#889 = PLANE ( 'NONE', #45302 ) ; +#890 = PRESENTATION_STYLE_ASSIGNMENT (( #24917 ) ) ; +#891 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#892 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81636 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37823, #68922, #39314 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#893 = VECTOR ( 'NONE', #24933, 1000.000000000000000 ) ; +#894 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#895 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, -0.01500000000000001506, -0.2400000000000000189 ) ) ; +#896 = ORIENTED_EDGE ( 'NONE', *, *, #89402, .T. ) ; +#897 = PRESENTATION_STYLE_ASSIGNMENT (( #56057 ) ) ; +#898 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#900 = STYLED_ITEM ( 'NONE', ( #43929 ), #28070 ) ; +#899 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18817 ), #10566 ) ; +#901 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100259 ) ) ; +#902 = SURFACE_STYLE_USAGE ( .BOTH. , #56573 ) ; +#904 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8648700000000000276 ) ) ; +#903 = LINE ( 'NONE', #2426, #5189 ) ; +#905 = SURFACE_STYLE_USAGE ( .BOTH. , #62706 ) ; +#906 = AXIS2_PLACEMENT_3D ( 'NONE', #2245, #49731, #33392 ) ; +#907 = CIRCLE ( 'NONE', #91993, 1.462498829941430323 ) ; +#908 = CARTESIAN_POINT ( 'NONE', ( 1.715954649776489926, -1.507352529807550079, 0.8300000000000011813 ) ) ; +#909 = LINE ( 'NONE', #47370, #36911 ) ; +#910 = ORIENTED_EDGE ( 'NONE', *, *, #4740, .F. ) ; +#911 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#912 = EDGE_CURVE ( 'NONE', #79146, #55045, #33536, .T. ) ; +#913 = CARTESIAN_POINT ( 'NONE', ( 1.759379393379719936, -1.230342595016630014, 0.8299999999999994049 ) ) ; +#914 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#915 = AXIS2_PLACEMENT_3D ( 'NONE', #62231, #70349, #93307 ) ; +#916 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, 0.000000000000000000 ) ) ; +#917 = EDGE_CURVE ( 'NONE', #54849, #53458, #80000, .T. ) ; +#918 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#919 = VERTEX_POINT ( 'NONE', #7923 ) ; +#920 = ORIENTED_EDGE ( 'NONE', *, *, #78390, .T. ) ; +#921 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#922 = ORIENTED_EDGE ( 'NONE', *, *, #39640, .F. ) ; +#923 = CARTESIAN_POINT ( 'NONE', ( 0.3027121684171390492, -0.9750598911029030313, 0.8299999999999996270 ) ) ; +#924 = STYLED_ITEM ( 'NONE', ( #61774 ), #72986 ) ; +#925 = SURFACE_STYLE_FILL_AREA ( #71895 ) ; +#926 = FILL_AREA_STYLE ('',( #9005 ) ) ; +#927 = PRESENTATION_STYLE_ASSIGNMENT (( #48922 ) ) ; +#928 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#929 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #43669 ) ; +#930 = LINE ( 'NONE', #87710, #75319 ) ; +#931 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30207 ) ) ; +#934 = VERTEX_POINT ( 'NONE', #23863 ) ; +#933 = ORIENTED_EDGE ( 'NONE', *, *, #23039, .T. ) ; +#932 = EDGE_CURVE ( 'NONE', #15997, #61368, #70288, .T. ) ; +#935 = EDGE_LOOP ( 'NONE', ( #13521, #53719, #52224, #21928 ) ) ; +#936 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#937 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67686 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48854, #24375, #25379 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#938 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83412, 'distance_accuracy_value', 'NONE'); +#939 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100227 ) ) ; +#940 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#942 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#941 = SURFACE_STYLE_USAGE ( .BOTH. , #54591 ) ; +#943 = ORIENTED_EDGE ( 'NONE', *, *, #50774, .T. ) ; +#944 = ADVANCED_FACE ( 'NONE', ( #81009 ), #10420, .F. ) ; +#945 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#946 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#947 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.699999999999999734, 0.8299999999999999600 ) ) ; +#948 = ORIENTED_EDGE ( 'NONE', *, *, #84205, .F. ) ; +#950 = LINE ( 'NONE', #63270, #69455 ) ; +#949 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696238000000000135, 0.8991599999999999593 ) ) ; +#951 = VERTEX_POINT ( 'NONE', #11947 ) ; +#952 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#953 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#955 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#954 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000050182, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#956 = ORIENTED_EDGE ( 'NONE', *, *, #19629, .T. ) ; +#957 = EDGE_LOOP ( 'NONE', ( #1560, #40124, #83581, #32996 ) ) ; +#958 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#959 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47245 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90349, #81722, #82216 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#960 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.525171249457494580E-10, 0.000000000000000000 ) ) ; +#962 = EDGE_CURVE ( 'NONE', #79785, #99402, #50386, .T. ) ; +#961 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#963 = EDGE_LOOP ( 'NONE', ( #19858, #54618, #3471, #68468, #66614, #99073, #14978, #6499, #30436, #70529, #4682, #30273 ) ) ; +#964 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.266666666666647068, 0.000000000000000000 ) ) ; +#965 = PLANE ( 'NONE', #205 ) ; +#966 = SURFACE_STYLE_FILL_AREA ( #69356 ) ; +#967 = ORIENTED_EDGE ( 'NONE', *, *, #46023, .F. ) ; +#968 = DIRECTION ( 'NONE', ( -0.7071062811868787934, 0.7071072811858626350, 0.000000000000000000 ) ) ; +#969 = ORIENTED_EDGE ( 'NONE', *, *, #86538, .F. ) ; +#970 = EDGE_CURVE ( 'NONE', #95604, #34620, #42198, .T. ) ; +#971 = ORIENTED_EDGE ( 'NONE', *, *, #63020, .F. ) ; +#972 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#973 = LINE ( 'NONE', #48474, #28622 ) ; +#974 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66212 ), #51658 ) ; +#975 = FILL_AREA_STYLE_COLOUR ( '', #74163 ) ; +#976 = CARTESIAN_POINT ( 'NONE', ( -0.5424062986694020427, -1.258396457361969922, 0.8100000000000000533 ) ) ; +#977 = FACE_OUTER_BOUND ( 'NONE', #28490, .T. ) ; +#978 = VECTOR ( 'NONE', #34792, 1000.000000000000000 ) ; +#979 = ADVANCED_FACE ( 'NONE', ( #73831 ), #81527, .T. ) ; +#981 = EDGE_CURVE ( 'NONE', #11295, #43512, #43661, .T. ) ; +#980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#982 = PLANE ( 'NONE', #30904 ) ; +#983 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89563, 'distance_accuracy_value', 'NONE'); +#984 = VECTOR ( 'NONE', #89854, 1000.000000000000000 ) ; +#985 = LINE ( 'NONE', #47951, #81780 ) ; +#986 = VERTEX_POINT ( 'NONE', #12455 ) ; +#987 = ORIENTED_EDGE ( 'NONE', *, *, #7493, .F. ) ; +#988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84221 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79470, #32500, #39132 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#989 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#990 = EDGE_CURVE ( 'NONE', #27941, #69488, #74826, .T. ) ; +#991 = EDGE_CURVE ( 'NONE', #79372, #41179, #18151, .T. ) ; +#992 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#993 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#994 = LINE ( 'NONE', #32146, #44591 ) ; +#995 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#996 = FILL_AREA_STYLE ('',( #70945 ) ) ; +#997 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, 0.1400000000000000133 ) ) ; +#998 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9833333333333335036, 0.000000000000000000 ) ) ; +#999 = EDGE_CURVE ( 'NONE', #32847, #34839, #96273, .T. ) ; +#1000 = SURFACE_STYLE_FILL_AREA ( #55655 ) ; +#1001 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1002 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#1003 = VECTOR ( 'NONE', #35428, 1000.000000000000000 ) ; +#1004 = LINE ( 'NONE', #32158, #19001 ) ; +#1005 = EDGE_CURVE ( 'NONE', #45817, #45151, #79696, .T. ) ; +#1006 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#1007 = AXIS2_PLACEMENT_3D ( 'NONE', #14115, #44279, #45268 ) ; +#1008 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.449999999999999956, 0.000000000000000000 ) ) ; +#1009 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#1010 = FILL_AREA_STYLE ('',( #70957 ) ) ; +#1011 = LINE ( 'NONE', #71464, #8671 ) ; +#1012 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72872 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85487, #63045, #1231 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1013 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36892, #84836, #37413, #46529 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1014 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1015 = EDGE_LOOP ( 'NONE', ( #72424, #3095, #25236, #89719 ) ) ; +#1016 = LINE ( 'NONE', #53635, #65553 ) ; +#1017 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7154, 'distance_accuracy_value', 'NONE'); +#1018 = VERTEX_POINT ( 'NONE', #68141 ) ; +#1019 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12213, 'distance_accuracy_value', 'NONE'); +#1020 = AXIS2_PLACEMENT_3D ( 'NONE', #85362, #79227, #55268 ) ; +#1021 = LINE ( 'NONE', #94426, #43134 ) ; +#1023 = VECTOR ( 'NONE', #20156, 1000.000000000000000 ) ; +#1022 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#1024 = FACE_OUTER_BOUND ( 'NONE', #59747, .T. ) ; +#1025 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#1026 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38964 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21302, #73936, #35661 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1027 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1028 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8800, #40045, #71178, #85992 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1029 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100936 ) ; +#1030 = VECTOR ( 'NONE', #11419, 1000.000000000000000 ) ; +#1031 = ORIENTED_EDGE ( 'NONE', *, *, #100645, .T. ) ; +#1032 = EDGE_LOOP ( 'NONE', ( #83488, #87394, #77701, #4351 ) ) ; +#1033 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98923 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41203, #87652, #2902 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1034 = ADVANCED_FACE ( 'NONE', ( #5336 ), #82992, .T. ) ; +#1035 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15316, 'distance_accuracy_value', 'NONE'); +#1036 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1037 = FILL_AREA_STYLE ('',( #71490 ) ) ; +#1038 = LINE ( 'NONE', #40360, #10143 ) ; +#1039 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1040 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#1041 = EDGE_CURVE ( 'NONE', #90613, #31464, #36545, .T. ) ; +#1042 = EDGE_LOOP ( 'NONE', ( #73445, #9397, #89964, #94618 ) ) ; +#1043 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#1044 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56810, #32290, #8202, #31264 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1045 = ORIENTED_EDGE ( 'NONE', *, *, #71763, .F. ) ; +#1046 = ORIENTED_EDGE ( 'NONE', *, *, #482, .T. ) ; +#1047 = PRESENTATION_STYLE_ASSIGNMENT (( #79166 ) ) ; +#1048 = CARTESIAN_POINT ( 'NONE', ( 1.039609075668130211, -1.335706927508150121, 0.8100000000000000533 ) ) ; +#1049 = FACE_OUTER_BOUND ( 'NONE', #9367, .T. ) ; +#1050 = STYLED_ITEM ( 'NONE', ( #20151 ), #14022 ) ; +#1051 = LINE ( 'NONE', #16840, #16888 ) ; +#1052 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#1054 = EDGE_LOOP ( 'NONE', ( #89903, #40729, #68608, #95051 ) ) ; +#1053 = ORIENTED_EDGE ( 'NONE', *, *, #5742, .T. ) ; +#1055 = VECTOR ( 'NONE', #8910, 1000.000000000000000 ) ; +#1056 = PLANE ( 'NONE', #76164 ) ; +#1057 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#1058 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#1059 = ORIENTED_EDGE ( 'NONE', *, *, #69836, .T. ) ; +#1060 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1061 = LINE ( 'NONE', #63873, #49628 ) ; +#1062 = ORIENTED_EDGE ( 'NONE', *, *, #61647, .T. ) ; +#1064 = EDGE_CURVE ( 'NONE', #90254, #78572, #68644, .T. ) ; +#1063 = VERTEX_POINT ( 'NONE', #67637 ) ; +#1065 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1066 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#1067 = SURFACE_STYLE_FILL_AREA ( #45976 ) ; +#1068 = SURFACE_STYLE_USAGE ( .BOTH. , #56742 ) ; +#1069 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8991599999999999593 ) ) ; +#1070 = EDGE_LOOP ( 'NONE', ( #22381, #47537, #33732, #22371 ) ) ; +#1071 = ORIENTED_EDGE ( 'NONE', *, *, #66501, .T. ) ; +#1072 = ORIENTED_EDGE ( 'NONE', *, *, #53990, .F. ) ; +#1073 = VECTOR ( 'NONE', #78707, 1000.000000000000000 ) ; +#1074 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34750, #34250, #2084, #41399 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1076 = ORIENTED_EDGE ( 'NONE', *, *, #24662, .T. ) ; +#1075 = CARTESIAN_POINT ( 'NONE', ( 5.646583124874956283, 2.700329875125043966, 0.8648700000000000276 ) ) ; +#1077 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1078 = VECTOR ( 'NONE', #36811, 1000.000000000000000 ) ; +#1079 = AXIS2_PLACEMENT_3D ( 'NONE', #81150, #34693, #36689 ) ; +#1080 = PRESENTATION_STYLE_ASSIGNMENT (( #47543 ) ) ; +#1081 = FILL_AREA_STYLE ('',( #71033 ) ) ; +#1082 = ORIENTED_EDGE ( 'NONE', *, *, #51302, .T. ) ; +#1083 = LINE ( 'NONE', #71554, #58239 ) ; +#1084 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#1085 = ORIENTED_EDGE ( 'NONE', *, *, #69228, .F. ) ; +#1086 = VECTOR ( 'NONE', #98374, 1000.000000000000000 ) ; +#1087 = LINE ( 'NONE', #25117, #98567 ) ; +#1088 = VECTOR ( 'NONE', #57382, 1000.000000000000000 ) ; +#1089 = DIRECTION ( 'NONE', ( 0.9684929325968363312, -0.2490410398106700507, 0.000000000000000000 ) ) ; +#1090 = STYLED_ITEM ( 'NONE', ( #4841 ), #78786 ) ; +#1091 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#1093 = ORIENTED_EDGE ( 'NONE', *, *, #34427, .T. ) ; +#1092 = FILL_AREA_STYLE ('',( #70528 ) ) ; +#1094 = FACE_OUTER_BOUND ( 'NONE', #50486, .T. ) ; +#1095 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1097 = FILL_AREA_STYLE ('',( #94506 ) ) ; +#1096 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#1098 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1099 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#1100 = FACE_OUTER_BOUND ( 'NONE', #75939, .T. ) ; +#1101 = ORIENTED_EDGE ( 'NONE', *, *, #75748, .T. ) ; +#1102 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51348, #82488, #36031, #45133 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1103 = PRESENTATION_STYLE_ASSIGNMENT (( #49104 ) ) ; +#1104 = EDGE_CURVE ( 'NONE', #85305, #47287, #100743, .T. ) ; +#1105 = SURFACE_SIDE_STYLE ('',( #9694 ) ) ; +#1106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94226 ), #2728 ) ; +#1107 = VECTOR ( 'NONE', #72246, 1000.000000000000000 ) ; +#1108 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#1109 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#1110 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1111 = CLOSED_SHELL ( 'NONE', ( #47796, #59338, #77457, #80450, #40153, #57497 ) ) ; +#1112 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1113 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56620 ) ) ; +#1114 = VECTOR ( 'NONE', #57449, 1000.000000000000000 ) ; +#1115 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1116 = ORIENTED_EDGE ( 'NONE', *, *, #4791, .F. ) ; +#1117 = FACE_OUTER_BOUND ( 'NONE', #68686, .T. ) ; +#1118 = EDGE_CURVE ( 'NONE', #59367, #64979, #84482, .T. ) ; +#1119 = EDGE_LOOP ( 'NONE', ( #17132, #39905, #66994, #27290 ) ) ; +#1120 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1121 = PRESENTATION_STYLE_ASSIGNMENT (( #23113 ) ) ; +#1122 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1123 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1124 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#1125 = ORIENTED_EDGE ( 'NONE', *, *, #21748, .F. ) ; +#1126 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#1127 = CARTESIAN_POINT ( 'NONE', ( -0.1139798271265630020, -1.164588072778879990, 0.8300000000000005151 ) ) ; +#1128 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1129 = LINE ( 'NONE', #93515, #23780 ) ; +#1130 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1131 = CYLINDRICAL_SURFACE ( 'NONE', #27985, 0.009999999999999998473 ) ; +#1132 = CARTESIAN_POINT ( 'NONE', ( -0.2761799387799139804, -3.099999999999980105, 0.000000000000000000 ) ) ; +#1133 = CARTESIAN_POINT ( 'NONE', ( -0.008621852316070110350, -0.9218577280486121017, 0.8299999999999999600 ) ) ; +#1134 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8648700000000000276 ) ) ; +#1135 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25242, 'distance_accuracy_value', 'NONE'); +#1136 = ADVANCED_FACE ( 'NONE', ( #38035 ), #90654, .T. ) ; +#1137 = AXIS2_PLACEMENT_3D ( 'NONE', #77590, #46421, #56149 ) ; +#1138 = FACE_OUTER_BOUND ( 'NONE', #40288, .T. ) ; +#1139 = ORIENTED_EDGE ( 'NONE', *, *, #34912, .F. ) ; +#1140 = ORIENTED_EDGE ( 'NONE', *, *, #77523, .T. ) ; +#1141 = LINE ( 'NONE', #93531, #30688 ) ; +#1142 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9708, 'distance_accuracy_value', 'NONE'); +#1143 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86077, 'distance_accuracy_value', 'NONE'); +#1144 = SURFACE_STYLE_FILL_AREA ( #56327 ) ; +#1145 = LINE ( 'NONE', #55801, #98137 ) ; +#1146 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12517 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84764, #45925, #30615 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1147 = VECTOR ( 'NONE', #21846, 1000.000000000000114 ) ; +#1148 = CARTESIAN_POINT ( 'NONE', ( 0.01835565287466199916, -1.473933850988760064, 0.8300000000000004041 ) ) ; +#1149 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1150 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31589, #30543, #37755, #46381, #38255, #92818, #39238, #21920, #29577, #68851, #31084, #22939, #76536, #99910, #100885, #7010, #22416, #78060, #54075 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 0.06596513480276100516, 0.1285982788375099606, 0.1878882902772209817, 0.2447239405482399821, 0.2995367614446490245, 0.3525418301580259817, 0.4056671456328589942, 0.4593140202066160471, 0.5138013296057499790, 0.5706505866881359523, 0.6313299304217719898, 0.6948490099838550149, 0.7637868806071289596, 0.8367871060470970512, 0.9153891099946711574, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1151 = FACE_OUTER_BOUND ( 'NONE', #49942, .T. ) ; +#1152 = ADVANCED_FACE ( 'NONE', ( #720 ), #48732, .T. ) ; +#1153 = ORIENTED_EDGE ( 'NONE', *, *, #44097, .T. ) ; +#1154 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8648700000000000276 ) ) ; +#1155 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87013, 'distance_accuracy_value', 'NONE'); +#1156 = LINE ( 'NONE', #22638, #90007 ) ; +#1157 = EDGE_LOOP ( 'NONE', ( #25715, #53734, #68636, #9001 ) ) ; +#1158 = CARTESIAN_POINT ( 'NONE', ( 1.281134210697184805, -1.245397870623744074, 0.8099999999998354072 ) ) ; +#1159 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45144 ), #82730 ) ; +#1160 = EDGE_LOOP ( 'NONE', ( #65987, #1692, #82112, #94969, #73670, #27593 ) ) ; +#1161 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1162 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.099999999999999867, 0.000000000000000000 ) ) ; +#1163 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#1164 = VECTOR ( 'NONE', #58318, 1000.000000000000000 ) ; +#1165 = VERTEX_POINT ( 'NONE', #48230 ) ; +#1166 = SURFACE_SIDE_STYLE ('',( #71126 ) ) ; +#1168 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5928 ), #38632 ) ; +#1167 = LINE ( 'NONE', #48157, #54462 ) ; +#1169 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#1170 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1171 = CLOSED_SHELL ( 'NONE', ( #50035, #25779, #26722, #19451, #12559, #8573 ) ) ; +#1173 = EDGE_CURVE ( 'NONE', #33175, #79146, #94872, .T. ) ; +#1172 = ORIENTED_EDGE ( 'NONE', *, *, #75335, .F. ) ; +#1174 = CIRCLE ( 'NONE', #28873, 0.04999999999999991257 ) ; +#1175 = PLANE ( 'NONE', #72325 ) ; +#1176 = FILL_AREA_STYLE ('',( #33869 ) ) ; +#1177 = ORIENTED_EDGE ( 'NONE', *, *, #85460, .F. ) ; +#1179 = ORIENTED_EDGE ( 'NONE', *, *, #31270, .T. ) ; +#1178 = ORIENTED_EDGE ( 'NONE', *, *, #73110, .T. ) ; +#1180 = LINE ( 'NONE', #9774, #48280 ) ; +#1181 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9276 ) ) ; +#1182 = ORIENTED_EDGE ( 'NONE', *, *, #93317, .T. ) ; +#1183 = AXIS2_PLACEMENT_3D ( 'NONE', #47546, #25601, #70521 ) ; +#1184 = SURFACE_STYLE_USAGE ( .BOTH. , #69196 ) ; +#1185 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#1186 = ORIENTED_EDGE ( 'NONE', *, *, #58456, .T. ) ; +#1188 = EDGE_LOOP ( 'NONE', ( #12262, #70208, #23964, #94778 ) ) ; +#1187 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#1189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1190 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1191 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#1192 = ORIENTED_EDGE ( 'NONE', *, *, #5242, .T. ) ; +#1193 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#1194 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#1195 = ORIENTED_EDGE ( 'NONE', *, *, #54577, .F. ) ; +#1196 = ADVANCED_FACE ( 'NONE', ( #1228 ), #47699, .T. ) ; +#1197 = FILL_AREA_STYLE ('',( #62513 ) ) ; +#1198 = ADVANCED_FACE ( 'NONE', ( #100681 ), #78842, .T. ) ; +#1199 = PRESENTATION_STYLE_ASSIGNMENT (( #65019 ) ) ; +#1200 = PRESENTATION_STYLE_ASSIGNMENT (( #47676 ) ) ; +#1201 = LINE ( 'NONE', #33385, #74429 ) ; +#1202 = AXIS2_PLACEMENT_3D ( 'NONE', #57601, #35612, #27952 ) ; +#1203 = ORIENTED_EDGE ( 'NONE', *, *, #87214, .T. ) ; +#1204 = VECTOR ( 'NONE', #41199, 1000.000000000000000 ) ; +#1206 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1207 = ORIENTED_EDGE ( 'NONE', *, *, #15476, .T. ) ; +#1208 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#1209 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6035 ), #97393 ) ; +#1210 = LINE ( 'NONE', #95122, #53907 ) ; +#1211 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1212 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#1213 = EDGE_CURVE ( 'NONE', #25531, #67337, #55888, .T. ) ; +#1214 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58598 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14662, #93774, #69284 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1215 = VECTOR ( 'NONE', #77337, 1000.000000000000000 ) ; +#1216 = ORIENTED_EDGE ( 'NONE', *, *, #76163, .F. ) ; +#1218 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1217 = CARTESIAN_POINT ( 'NONE', ( 6.678959124874999986, 8.385468875124999499, 0.8648700000000000276 ) ) ; +#1219 = PRESENTATION_STYLE_ASSIGNMENT (( #78835 ) ) ; +#1220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89289 ) ) ; +#1221 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 7.671291000000000082, 0.8991599999999999593 ) ) ; +#1222 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59337, 'distance_accuracy_value', 'NONE'); +#1223 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1224 = AXIS2_PLACEMENT_3D ( 'NONE', #1871, #70791, #93231 ) ; +#1225 = LINE ( 'NONE', #55885, #66956 ) ; +#1226 = CARTESIAN_POINT ( 'NONE', ( 11.51556912487501272, 7.437945124875012581, 0.8648700000000000276 ) ) ; +#1227 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1228 = FACE_OUTER_BOUND ( 'NONE', #93099, .T. ) ; +#1229 = SURFACE_STYLE_FILL_AREA ( #95138 ) ; +#1230 = EDGE_CURVE ( 'NONE', #7394, #8122, #1766, .T. ) ; +#1231 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1232 = VECTOR ( 'NONE', #17136, 1000.000000000000000 ) ; +#1233 = ORIENTED_EDGE ( 'NONE', *, *, #74468, .T. ) ; +#1234 = PRESENTATION_STYLE_ASSIGNMENT (( #8810 ) ) ; +#1235 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1236 = VECTOR ( 'NONE', #26277, 1000.000000000000000 ) ; +#1237 = VECTOR ( 'NONE', #11710, 1000.000000000000000 ) ; +#1239 = FILL_AREA_STYLE ('',( #87029 ) ) ; +#1238 = SURFACE_SIDE_STYLE ('',( #48235 ) ) ; +#1240 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#1241 = VECTOR ( 'NONE', #57433, 1000.000000000000000 ) ; +#1242 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1243 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1244 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1245 = SURFACE_STYLE_USAGE ( .BOTH. , #23742 ) ; +#1246 = CLOSED_SHELL ( 'NONE', ( #1818, #42710, #79412, #73142, #39563, #1559 ) ) ; +#1247 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1248 = ORIENTED_EDGE ( 'NONE', *, *, #98675, .F. ) ; +#1249 = PRESENTATION_STYLE_ASSIGNMENT (( #15530 ) ) ; +#1250 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -3.500000000000000444, 1.308546363094771468E-78 ) ) ; +#1251 = FILL_AREA_STYLE_COLOUR ( '', #42445 ) ; +#1252 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1253 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#1254 = SURFACE_STYLE_FILL_AREA ( #41092 ) ; +#1255 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1256 = PLANE ( 'NONE', #53437 ) ; +#1257 = SURFACE_STYLE_USAGE ( .BOTH. , #63580 ) ; +#1258 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1259 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46057 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81388, #11311, #67030 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1260 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1261 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1262 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#1263 = STYLED_ITEM ( 'NONE', ( #34653 ), #14870 ) ; +#1264 = EDGE_CURVE ( 'NONE', #14950, #77426, #53506, .T. ) ; +#1265 = LINE ( 'NONE', #80917, #56683 ) ; +#1266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1267 = FACE_OUTER_BOUND ( 'NONE', #26893, .T. ) ; +#1268 = STYLED_ITEM ( 'NONE', ( #96506 ), #49991 ) ; +#1269 = CARTESIAN_POINT ( 'NONE', ( -0.8110130133854057677, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#1270 = ORIENTED_EDGE ( 'NONE', *, *, #73008, .T. ) ; +#1271 = FILL_AREA_STYLE_COLOUR ( '', #98475 ) ; +#1272 = ORIENTED_EDGE ( 'NONE', *, *, #36842, .F. ) ; +#1273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99536, 'distance_accuracy_value', 'NONE'); +#1274 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43605 ) ) ; +#1275 = SURFACE_SIDE_STYLE ('',( #46708 ) ) ; +#1276 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#1277 = CARTESIAN_POINT ( 'NONE', ( 0.1485744800866570237, -1.491420757567720079, 0.8299999999999999600 ) ) ; +#1278 = FILL_AREA_STYLE_COLOUR ( '', #28078 ) ; +#1279 = LINE ( 'NONE', #768, #77644 ) ; +#1280 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -11.41999999999999993 ) ) ; +#1281 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1282 = EDGE_CURVE ( 'NONE', #58057, #64584, #32895, .T. ) ; +#1283 = ORIENTED_EDGE ( 'NONE', *, *, #39350, .F. ) ; +#1284 = SURFACE_SIDE_STYLE ('',( #62595 ) ) ; +#1285 = SURFACE_STYLE_FILL_AREA ( #78893 ) ; +#1286 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87725, 'distance_accuracy_value', 'NONE'); +#1287 = LINE ( 'NONE', #79414, #94799 ) ; +#1288 = AXIS2_PLACEMENT_3D ( 'NONE', #69975, #92923, #85809 ) ; +#1289 = SURFACE_SIDE_STYLE ('',( #47753 ) ) ; +#1290 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85973 ), #17591 ) ; +#1291 = VERTEX_POINT ( 'NONE', #2760 ) ; +#1292 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1293 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#1294 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1295 = VECTOR ( 'NONE', #69660, 1000.000000000000000 ) ; +#1296 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 2.710505431213761085E-17, -0.6199999999999999956 ) ) ; +#1297 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.000000000000000000 ) ) ; +#1298 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#1299 = VERTEX_POINT ( 'NONE', #73702 ) ; +#1300 = FACE_OUTER_BOUND ( 'NONE', #53578, .T. ) ; +#1301 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #704, 'distance_accuracy_value', 'NONE'); +#1302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62717 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18078, #16573, #40101 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1303 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21741 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17439, #72103, #62952 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1304 = SURFACE_STYLE_FILL_AREA ( #23795 ) ; +#1305 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1306 = ORIENTED_EDGE ( 'NONE', *, *, #24587, .T. ) ; +#1307 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1308 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#1309 = LINE ( 'NONE', #16592, #57388 ) ; +#1310 = ORIENTED_EDGE ( 'NONE', *, *, #67469, .T. ) ; +#1311 = VECTOR ( 'NONE', #52730, 1000.000000000000000 ) ; +#1312 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#1313 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1314 = EDGE_CURVE ( 'NONE', #41918, #55234, #68276, .T. ) ; +#1315 = VECTOR ( 'NONE', #49133, 1000.000000000000000 ) ; +#1316 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38732 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50529, #32673, #25030 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1317 = VERTEX_POINT ( 'NONE', #49226 ) ; +#1319 = ORIENTED_EDGE ( 'NONE', *, *, #58395, .T. ) ; +#1318 = FILL_AREA_STYLE_COLOUR ( '', #83441 ) ; +#1320 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1321 = FILL_AREA_STYLE ('',( #23815 ) ) ; +#1322 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8991599999999999593 ) ) ; +#1323 = CLOSED_SHELL ( 'NONE', ( #71528, #94546, #39598, #79541, #75119, #84361 ) ) ; +#1324 = CARTESIAN_POINT ( 'NONE', ( -0.3919372300192849878, -0.9729160362892149694, 0.8299999999999999600 ) ) ; +#1325 = ORIENTED_EDGE ( 'NONE', *, *, #26439, .T. ) ; +#1326 = ADVANCED_FACE ( 'NONE', ( #35438 ), #96148, .T. ) ; +#1327 = PRESENTATION_STYLE_ASSIGNMENT (( #17632 ) ) ; +#1328 = CARTESIAN_POINT ( 'NONE', ( 0.9366369866146577738, 0.4412590759269662821, 0.8100000000000000533 ) ) ; +#1329 = EDGE_CURVE ( 'NONE', #71312, #99345, #42571, .T. ) ; +#1330 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#1331 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.000000000000000000, 1.149999999999999911 ) ) ; +#1332 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1333 = ORIENTED_EDGE ( 'NONE', *, *, #73195, .T. ) ; +#1334 = AXIS2_PLACEMENT_3D ( 'NONE', #92857, #53614, #84737 ) ; +#1335 = ADVANCED_FACE ( 'NONE', ( #33411 ), #26756, .T. ) ; +#1337 = SURFACE_STYLE_FILL_AREA ( #32987 ) ; +#1336 = LINE ( 'NONE', #62641, #7893 ) ; +#1338 = ORIENTED_EDGE ( 'NONE', *, *, #67493, .T. ) ; +#1339 = VERTEX_POINT ( 'NONE', #81886 ) ; +#1340 = LINE ( 'NONE', #32496, #8512 ) ; +#1341 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64973 ), #20869 ) ; +#1343 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1342 = LINE ( 'NONE', #72805, #18548 ) ; +#1344 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22625 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57778, #97515, #11175 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1345 = VERTEX_POINT ( 'NONE', #11821 ) ; +#1346 = AXIS2_PLACEMENT_3D ( 'NONE', #93019, #68560, #44571 ) ; +#1347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1348 = SURFACE_STYLE_FILL_AREA ( #32505 ) ; +#1349 = EDGE_CURVE ( 'NONE', #13692, #1299, #90016, .T. ) ; +#1350 = EDGE_LOOP ( 'NONE', ( #89352, #36355, #88803, #45970 ) ) ; +#1351 = CARTESIAN_POINT ( 'NONE', ( 1.314898002023040080, -1.423389424083600030, 0.8299999999999999600 ) ) ; +#1352 = SURFACE_STYLE_FILL_AREA ( #40172 ) ; +#1353 = ORIENTED_EDGE ( 'NONE', *, *, #65240, .T. ) ; +#1354 = VERTEX_POINT ( 'NONE', #85247 ) ; +#1355 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7499999999822648533, 0.000000000000000000 ) ) ; +#1356 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1357 = LINE ( 'NONE', #70280, #61611 ) ; +#1358 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#1360 = EDGE_CURVE ( 'NONE', #92204, #46104, #70418, .T. ) ; +#1359 = LINE ( 'NONE', #77956, #82406 ) ; +#1361 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #94762, .NOT_KNOWN. ) ; +#1362 = PLANE ( 'NONE', #58981 ) ; +#1363 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51886 ), #61727 ) ; +#1364 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#1365 = SURFACE_STYLE_FILL_AREA ( #77963 ) ; +#1366 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1367 = FACE_OUTER_BOUND ( 'NONE', #55596, .T. ) ; +#1368 = EDGE_CURVE ( 'NONE', #62254, #95096, #38796, .T. ) ; +#1369 = AXIS2_PLACEMENT_3D ( 'NONE', #66544, #45043, #19585 ) ; +#1370 = VERTEX_POINT ( 'NONE', #31135 ) ; +#1371 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1372 = ADVANCED_FACE ( 'NONE', ( #44541 ), #15263, .T. ) ; +#1374 = FILL_AREA_STYLE_COLOUR ( '', #73725 ) ; +#1373 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#1375 = SURFACE_STYLE_USAGE ( .BOTH. , #77451 ) ; +#1376 = VECTOR ( 'NONE', #68188, 1000.000000000000000 ) ; +#1377 = EDGE_CURVE ( 'NONE', #1018, #12539, #12847, .T. ) ; +#1378 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91195 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37332, #29156, #82770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1379 = SURFACE_STYLE_USAGE ( .BOTH. , #71319 ) ; +#1380 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1381 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000622, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#1382 = SURFACE_SIDE_STYLE ('',( #40196 ) ) ; +#1383 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #83286 ) ) ; +#1385 = ORIENTED_EDGE ( 'NONE', *, *, #24349, .T. ) ; +#1384 = VECTOR ( 'NONE', #23906, 1000.000000000000000 ) ; +#1386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1387 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1388 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1389 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 10.39365100000000020, 0.8648700000000000276 ) ) ; +#1390 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#1391 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1392 = VECTOR ( 'NONE', #41446, 1000.000000000000000 ) ; +#1393 = CARTESIAN_POINT ( 'NONE', ( 2.973719124875012554, 5.373193124875012217, 0.8991599999999999593 ) ) ; +#1394 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76384, 'distance_accuracy_value', 'NONE'); +#1395 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 2.914335439641030002E-16 ) ) ; +#1396 = SURFACE_STYLE_FILL_AREA ( #56556 ) ; +#1397 = LINE ( 'NONE', #32032, #20386 ) ; +#1398 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1399 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43799 ) ) ; +#1400 = SURFACE_STYLE_FILL_AREA ( #93761 ) ; +#1401 = EDGE_CURVE ( 'NONE', #36263, #50760, #100872, .T. ) ; +#1403 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1402 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1404 = FILL_AREA_STYLE ('',( #71339 ) ) ; +#1405 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64947 ) ) ; +#1406 = SURFACE_STYLE_FILL_AREA ( #71856 ) ; +#1407 = SURFACE_STYLE_USAGE ( .BOTH. , #94795 ) ; +#1408 = AXIS2_PLACEMENT_3D ( 'NONE', #14548, #77882, #55446 ) ; +#1409 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1410 = FILL_AREA_STYLE_COLOUR ( '', #71388 ) ; +#1411 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1412 = SURFACE_SIDE_STYLE ('',( #46315 ) ) ; +#1413 = EDGE_CURVE ( 'NONE', #65827, #39488, #55162, .T. ) ; +#1414 = EDGE_LOOP ( 'NONE', ( #92616, #18090, #93506, #82569 ) ) ; +#1415 = FILL_AREA_STYLE ('',( #70852 ) ) ; +#1416 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5305, 'distance_accuracy_value', 'NONE'); +#1417 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#1418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99121 ), #60122 ) ; +#1419 = ADVANCED_FACE ( 'NONE', ( #98594 ), #93375, .T. ) ; +#1420 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#1421 = CARTESIAN_POINT ( 'NONE', ( 1.286957766637873091, -1.173454618603474886, 0.8099999999998808153 ) ) ; +#1422 = STYLED_ITEM ( 'NONE', ( #64201 ), #15066 ) ; +#1423 = CARTESIAN_POINT ( 'NONE', ( 1.775025884298160106, -1.496872818153279994, 0.8300000000000011813 ) ) ; +#1424 = STYLED_ITEM ( 'NONE', ( #91622 ), #50138 ) ; +#1425 = EDGE_LOOP ( 'NONE', ( #3761, #97598, #49, #67478 ) ) ; +#1426 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1427 = EDGE_CURVE ( 'NONE', #69332, #71811, #64791, .T. ) ; +#1428 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8099999999999629718 ) ) ; +#1429 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71111, 'distance_accuracy_value', 'NONE'); +#1430 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4808578643762691507, 0.2500000000000001110 ) ) ; +#1431 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2254, 'distance_accuracy_value', 'NONE'); +#1432 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1433 = SURFACE_STYLE_USAGE ( .BOTH. , #23927 ) ; +#1434 = ORIENTED_EDGE ( 'NONE', *, *, #71887, .F. ) ; +#1435 = VERTEX_POINT ( 'NONE', #96410 ) ; +#1436 = SURFACE_STYLE_USAGE ( .BOTH. , #39309 ) ; +#1437 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#1438 = VECTOR ( 'NONE', #1912, 1000.000000000000000 ) ; +#1439 = ORIENTED_EDGE ( 'NONE', *, *, #75567, .T. ) ; +#1440 = CARTESIAN_POINT ( 'NONE', ( 0.3405668653832410464, -0.9628054983551439516, 0.8299999999999996270 ) ) ; +#1441 = STYLED_ITEM ( 'NONE', ( #82595 ), #75080 ) ; +#1442 = FACE_OUTER_BOUND ( 'NONE', #64261, .T. ) ; +#1443 = PRESENTATION_STYLE_ASSIGNMENT (( #9520 ) ) ; +#1444 = ADVANCED_FACE ( 'NONE', ( #63807 ), #16278, .T. ) ; +#1445 = CARTESIAN_POINT ( 'NONE', ( -1.319753185035670073, -0.9379159637996590249, 0.8299999999999997380 ) ) ; +#1446 = ADVANCED_FACE ( 'NONE', ( #64294 ), #39804, .T. ) ; +#1447 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35722 ), #73177 ) ; +#1448 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #33269 ) ; +#1449 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#1450 = CARTESIAN_POINT ( 'NONE', ( 1.009497215679371118, -1.441493030236584261, 0.8099999999997122835 ) ) ; +#1452 = ORIENTED_EDGE ( 'NONE', *, *, #55710, .F. ) ; +#1451 = ORIENTED_EDGE ( 'NONE', *, *, #29843, .T. ) ; +#1453 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88595 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66380, #82703, #27097 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1454 = ORIENTED_EDGE ( 'NONE', *, *, #99352, .F. ) ; +#1455 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, 0.1500000000000000222 ) ) ; +#1456 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1457 = STYLED_ITEM ( 'NONE', ( #51280 ), #92026 ) ; +#1459 = SURFACE_SIDE_STYLE ('',( #71909 ) ) ; +#1458 = CARTESIAN_POINT ( 'NONE', ( 0.4785075026192849856, -0.9340610223455999561, 0.8100000000000000533 ) ) ; +#1460 = ORIENTED_EDGE ( 'NONE', *, *, #94811, .T. ) ; +#1461 = CIRCLE ( 'NONE', #86199, 0.009999999999999998473 ) ; +#1462 = VECTOR ( 'NONE', #38720, 1000.000000000000000 ) ; +#1463 = SURFACE_STYLE_FILL_AREA ( #33622 ) ; +#1464 = EDGE_CURVE ( 'NONE', #99759, #10390, #54599, .T. ) ; +#1465 = VERTEX_POINT ( 'NONE', #63324 ) ; +#1466 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1467 = ORIENTED_EDGE ( 'NONE', *, *, #49081, .T. ) ; +#1468 = EDGE_CURVE ( 'NONE', #28590, #72282, #49488, .T. ) ; +#1470 = SURFACE_STYLE_USAGE ( .BOTH. , #40278 ) ; +#1469 = SURFACE_STYLE_USAGE ( .BOTH. , #39759 ) ; +#1471 = ORIENTED_EDGE ( 'NONE', *, *, #2643, .F. ) ; +#1472 = ORIENTED_EDGE ( 'NONE', *, *, #19469, .T. ) ; +#1473 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1474 = VECTOR ( 'NONE', #76432, 1000.000000000000114 ) ; +#1475 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57043 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46442, #502, #97788 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1476 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1477 = LINE ( 'NONE', #33113, #94484 ) ; +#1478 = VECTOR ( 'NONE', #33919, 1000.000000000000000 ) ; +#1480 = ORIENTED_EDGE ( 'NONE', *, *, #26201, .T. ) ; +#1479 = LINE ( 'NONE', #19286, #85302 ) ; +#1481 = STYLED_ITEM ( 'NONE', ( #6242 ), #42399 ) ; +#1482 = FILL_AREA_STYLE ('',( #17270 ) ) ; +#1483 = LINE ( 'NONE', #31603, #58763 ) ; +#1484 = ORIENTED_EDGE ( 'NONE', *, *, #66268, .T. ) ; +#1485 = VECTOR ( 'NONE', #86877, 1000.000000000000000 ) ; +#1486 = CARTESIAN_POINT ( 'NONE', ( 0.02260986327491390155, -1.199770973383029959, 0.8299999999999999600 ) ) ; +#1487 = EDGE_LOOP ( 'NONE', ( #79839, #44124, #80566, #46364 ) ) ; +#1488 = ORIENTED_EDGE ( 'NONE', *, *, #39478, .F. ) ; +#1489 = FACE_OUTER_BOUND ( 'NONE', #84371, .T. ) ; +#1491 = EDGE_CURVE ( 'NONE', #42518, #57051, #65294, .T. ) ; +#1490 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#1492 = STYLED_ITEM ( 'NONE', ( #83876 ), #50791 ) ; +#1493 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#1494 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#1495 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#1496 = EDGE_CURVE ( 'NONE', #87432, #79701, #47964, .T. ) ; +#1497 = FILL_AREA_STYLE_COLOUR ( '', #8268 ) ; +#1498 = ORIENTED_EDGE ( 'NONE', *, *, #15939, .T. ) ; +#1499 = SURFACE_SIDE_STYLE ('',( #89650 ) ) ; +#1500 = LINE ( 'NONE', #73466, #85400 ) ; +#1501 = EDGE_LOOP ( 'NONE', ( #52072, #35115, #16626, #86052, #60047, #9275 ) ) ; +#1502 = EDGE_CURVE ( 'NONE', #63401, #23470, #58182, .T. ) ; +#1503 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1504 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1505 = PLANE ( 'NONE', #71253 ) ; +#1506 = LINE ( 'NONE', #87256, #49685 ) ; +#1508 = PRESENTATION_STYLE_ASSIGNMENT (( #10064 ) ) ; +#1507 = SURFACE_STYLE_FILL_AREA ( #9073 ) ; +#1509 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1510 = LINE ( 'NONE', #31628, #25593 ) ; +#1511 = LINE ( 'NONE', #9575, #30294 ) ; +#1512 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -3.614007241618339896E-16 ) ) ; +#1513 = PLANE ( 'NONE', #24868 ) ; +#1514 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1515 = SURFACE_SIDE_STYLE ('',( #66643 ) ) ; +#1516 = FACE_OUTER_BOUND ( 'NONE', #34769, .T. ) ; +#1517 = VECTOR ( 'NONE', #23826, 1000.000000000000000 ) ; +#1518 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1519 = SURFACE_STYLE_FILL_AREA ( #39286 ) ; +#1520 = VECTOR ( 'NONE', #65012, 1000.000000000000000 ) ; +#1521 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1522 = FILL_AREA_STYLE_COLOUR ( '', #86386 ) ; +#1523 = CYLINDRICAL_SURFACE ( 'NONE', #24173, 0.09999999999999999167 ) ; +#1524 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1525 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#1526 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33074 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45447, #7097, #15308 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1527 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1528 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81404, 'distance_accuracy_value', 'NONE'); +#1529 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27058 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12109, #82643, #15673 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1530 = ORIENTED_EDGE ( 'NONE', *, *, #95817, .T. ) ; +#1531 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#1532 = VECTOR ( 'NONE', #36497, 1000.000000000000114 ) ; +#1533 = ADVANCED_FACE ( 'NONE', ( #34688 ), #65813, .T. ) ; +#1534 = ORIENTED_EDGE ( 'NONE', *, *, #40102, .F. ) ; +#1535 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#1536 = VECTOR ( 'NONE', #52934, 1000.000000000000000 ) ; +#1537 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1538 = CARTESIAN_POINT ( 'NONE', ( 1.877470194538120030, -1.043958301690999901, 0.8299999999999999600 ) ) ; +#1539 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 2.438701000000000008, 0.8648700000000000276 ) ) ; +#1540 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71630 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27011, #23737, #63562 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1541 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#1542 = EDGE_CURVE ( 'NONE', #10022, #45477, #27020, .T. ) ; +#1543 = FACE_OUTER_BOUND ( 'NONE', #92770, .T. ) ; +#1544 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68356 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36709, #82662, #99384 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1546 = ORIENTED_EDGE ( 'NONE', *, *, #42612, .T. ) ; +#1547 = VERTEX_POINT ( 'NONE', #19328 ) ; +#1548 = EDGE_CURVE ( 'NONE', #17257, #3181, #81147, .T. ) ; +#1549 = LINE ( 'NONE', #18847, #36832 ) ; +#1550 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#1552 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30897 ) ) ; +#1551 = CYLINDRICAL_SURFACE ( 'NONE', #49873, 0.05000000000000012768 ) ; +#1553 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1554 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1555 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1556 = FILL_AREA_STYLE_COLOUR ( '', #89246 ) ; +#1557 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1558 = VECTOR ( 'NONE', #59174, 1000.000000000000000 ) ; +#1559 = ADVANCED_FACE ( 'NONE', ( #98366 ), #35193, .T. ) ; +#1560 = ORIENTED_EDGE ( 'NONE', *, *, #67130, .T. ) ; +#1561 = CARTESIAN_POINT ( 'NONE', ( 1.084155851675350002, -0.9900689134305371564, 0.8300000000000002931 ) ) ; +#1562 = ORIENTED_EDGE ( 'NONE', *, *, #50045, .T. ) ; +#1563 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1564 = ORIENTED_EDGE ( 'NONE', *, *, #25968, .T. ) ; +#1565 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#1566 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1567 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#1568 = ADVANCED_FACE ( 'NONE', ( #97892 ), #20329, .T. ) ; +#1570 = ADVANCED_FACE ( 'NONE', ( #14635 ), #6933, .T. ) ; +#1569 = AXIS2_PLACEMENT_3D ( 'NONE', #30764, #93022, #94557 ) ; +#1571 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.123820061220085265, 0.000000000000000000 ) ) ; +#1572 = CARTESIAN_POINT ( 'NONE', ( 9.881869999999999266, 12.69187200000000004, 0.8991599999999999593 ) ) ; +#1573 = FILL_AREA_STYLE_COLOUR ( '', #73653 ) ; +#1574 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1576 = ORIENTED_EDGE ( 'NONE', *, *, #39006, .T. ) ; +#1575 = ORIENTED_EDGE ( 'NONE', *, *, #53417, .T. ) ; +#1577 = DIRECTION ( 'NONE', ( -0.7071067811865489050, 0.7071067811865462405, 0.000000000000000000 ) ) ; +#1580 = ADVANCED_FACE ( 'NONE', ( #68776 ), #44793, .T. ) ; +#1579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88819 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6375, #44711, #51919 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1578 = SURFACE_STYLE_USAGE ( .BOTH. , #79698 ) ; +#1581 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1582 = ORIENTED_EDGE ( 'NONE', *, *, #82889, .T. ) ; +#1583 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.000000000000000000 ) ) ; +#1584 = PRESENTATION_STYLE_ASSIGNMENT (( #24069 ) ) ; +#1585 = ORIENTED_EDGE ( 'NONE', *, *, #5660, .F. ) ; +#1586 = VERTEX_POINT ( 'NONE', #5959 ) ; +#1587 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1588 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#1589 = ADVANCED_FACE ( 'NONE', ( #37189 ), #94783, .T. ) ; +#1590 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1591 = AXIS2_PLACEMENT_3D ( 'NONE', #73264, #3304, #2312 ) ; +#1592 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#1593 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, -0.000000000000000000 ) ) ; +#1594 = ORIENTED_EDGE ( 'NONE', *, *, #68017, .F. ) ; +#1595 = VERTEX_POINT ( 'NONE', #55537 ) ; +#1596 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#1597 = ORIENTED_EDGE ( 'NONE', *, *, #34327, .T. ) ; +#1598 = ADVANCED_FACE ( 'NONE', ( #48873 ), #39676, .T. ) ; +#1599 = LINE ( 'NONE', #56241, #90015 ) ; +#1600 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55460 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39244, #91863, #92358 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1601 = STYLED_ITEM ( 'NONE', ( #24481 ), #93265 ) ; +#1603 = ORIENTED_EDGE ( 'NONE', *, *, #90435, .T. ) ; +#1602 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1604 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17605 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77376, #84054, #39100 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1605 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.700000000000000622, 0.8299999999999999600 ) ) ; +#1606 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45551 ), #27709 ) ; +#1607 = CARTESIAN_POINT ( 'NONE', ( 11.49435687512499094, 6.539919875124987847, 0.8991599999999999593 ) ) ; +#1608 = CARTESIAN_POINT ( 'NONE', ( 1.810234811980210079, -1.482878949593630091, 0.8099999999999996092 ) ) ; +#1609 = ORIENTED_EDGE ( 'NONE', *, *, #3921, .T. ) ; +#1610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3202 ), #94495 ) ; +#1611 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1612 = CARTESIAN_POINT ( 'NONE', ( -0.9943488014102380701, -1.374487914949441780, 0.8099999999997120614 ) ) ; +#1613 = VERTEX_POINT ( 'NONE', #56548 ) ; +#1614 = AXIS2_PLACEMENT_3D ( 'NONE', #70231, #39609, #31955 ) ; +#1615 = CARTESIAN_POINT ( 'NONE', ( -1.313603896932107107, 0.7100000000000001865, -1.079289321881345298 ) ) ; +#1617 = LINE ( 'NONE', #572, #92556 ) ; +#1616 = AXIS2_PLACEMENT_3D ( 'NONE', #22994, #7564, #86264 ) ; +#1618 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#1620 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#1619 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1621 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#1622 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4797 ) ) ; +#1623 = CARTESIAN_POINT ( 'NONE', ( 1.496131215532870096, -1.321596304865350291, 0.8099999999999982769 ) ) ; +#1624 = AXIS2_PLACEMENT_3D ( 'NONE', #59067, #43683, #3404 ) ; +#1625 = CARTESIAN_POINT ( 'NONE', ( 1.702517484154870031, -1.219598171061480052, 0.8099999999999996092 ) ) ; +#1626 = VERTEX_POINT ( 'NONE', #16656 ) ; +#1627 = ADVANCED_FACE ( 'NONE', ( #86648 ), #47847, .T. ) ; +#1628 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#1629 = STYLED_ITEM ( 'NONE', ( #1249 ), #42710 ) ; +#1630 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1631 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#1632 = SURFACE_STYLE_FILL_AREA ( #64414 ) ; +#1633 = ADVANCED_FACE ( 'NONE', ( #73848 ), #74845, .T. ) ; +#1635 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#1634 = FILL_AREA_STYLE_COLOUR ( '', #83766 ) ; +#1636 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, 0.000000000000000000 ) ) ; +#1637 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#1638 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45579 ) ) ; +#1639 = AXIS2_PLACEMENT_3D ( 'NONE', #66803, #58687, #11595 ) ; +#1640 = PRESENTATION_STYLE_ASSIGNMENT (( #57284 ) ) ; +#1641 = SURFACE_STYLE_FILL_AREA ( #72084 ) ; +#1642 = PLANE ( 'NONE', #15339 ) ; +#1643 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78611 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32043, #16670, #58079 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1644 = ORIENTED_EDGE ( 'NONE', *, *, #13796, .T. ) ; +#1645 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1646 = ADVANCED_FACE ( 'NONE', ( #51881 ), #97773, .T. ) ; +#1647 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, -0.000000000000000000 ) ) ; +#1648 = FILL_AREA_STYLE ('',( #63451 ) ) ; +#1649 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1650 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35577, 'distance_accuracy_value', 'NONE'); +#1652 = ORIENTED_EDGE ( 'NONE', *, *, #35579, .T. ) ; +#1653 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#1654 = ADVANCED_FACE ( 'NONE', ( #96289 ), #50406, .T. ) ; +#1655 = SURFACE_STYLE_USAGE ( .BOTH. , #38932 ) ; +#1656 = FILL_AREA_STYLE_COLOUR ( '', #36030 ) ; +#1657 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#1658 = FACE_OUTER_BOUND ( 'NONE', #70902, .T. ) ; +#1659 = LINE ( 'NONE', #62441, #69731 ) ; +#1660 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#1661 = STYLED_ITEM ( 'NONE', ( #17460 ), #33154 ) ; +#1662 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1663 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, -3.500000000000000444, 0.000000000000000000 ) ) ; +#1664 = PLANE ( 'NONE', #67272 ) ; +#1665 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1666 = AXIS2_PLACEMENT_3D ( 'NONE', #82603, #45743, #92232 ) ; +#1667 = VECTOR ( 'NONE', #86256, 1000.000000000000000 ) ; +#1668 = FILL_AREA_STYLE_COLOUR ( '', #14313 ) ; +#1669 = FILL_AREA_STYLE ('',( #86930 ) ) ; +#1670 = EDGE_LOOP ( 'NONE', ( #38148, #47982, #65646, #67250 ) ) ; +#1671 = SURFACE_STYLE_FILL_AREA ( #9229 ) ; +#1672 = ORIENTED_EDGE ( 'NONE', *, *, #67456, .T. ) ; +#1673 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1674 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92460, 'distance_accuracy_value', 'NONE'); +#1675 = VECTOR ( 'NONE', #93839, 1000.000000000000000 ) ; +#1676 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1677 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#1678 = VECTOR ( 'NONE', #59499, 1000.000000000000114 ) ; +#1679 = STYLED_ITEM ( 'NONE', ( #68395 ), #94322 ) ; +#1680 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#1681 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1682 = LINE ( 'NONE', #8228, #61489 ) ; +#1683 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.000000000000000000 ) ) ; +#1684 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1685 = LINE ( 'NONE', #72612, #90116 ) ; +#1686 = EDGE_LOOP ( 'NONE', ( #36524, #92677, #35406, #7759 ) ) ; +#1687 = CARTESIAN_POINT ( 'NONE', ( 1.865911170909900108, -1.438073744133560039, 0.8300000000000011813 ) ) ; +#1688 = SURFACE_STYLE_USAGE ( .BOTH. , #71627 ) ; +#1689 = SURFACE_STYLE_USAGE ( .BOTH. , #39973 ) ; +#1690 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58775 ), #29362 ) ; +#1691 = FILL_AREA_STYLE_COLOUR ( '', #11711 ) ; +#1692 = ORIENTED_EDGE ( 'NONE', *, *, #35987, .F. ) ; +#1693 = CARTESIAN_POINT ( 'NONE', ( 1.235972998600387562, -1.233175053557127976, 0.8099999999998432898 ) ) ; +#1695 = SURFACE_STYLE_USAGE ( .BOTH. , #63965 ) ; +#1694 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78347 ) ) ; +#1696 = EDGE_LOOP ( 'NONE', ( #51705, #50222, #75524, #48915 ) ) ; +#1697 = FACE_OUTER_BOUND ( 'NONE', #7401, .T. ) ; +#1698 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91321 ) ) ; +#1699 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1700 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1701 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#1702 = EDGE_LOOP ( 'NONE', ( #6872, #13438, #55493, #37974 ) ) ; +#1703 = VECTOR ( 'NONE', #54466, 1000.000000000000000 ) ; +#1704 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1705 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1706 = EDGE_CURVE ( 'NONE', #40572, #38877, #54392, .T. ) ; +#1707 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.2999999999999999889, -13.40000000000000036 ) ) ; +#1708 = EDGE_LOOP ( 'NONE', ( #23134, #73789, #81227, #47295 ) ) ; +#1709 = SURFACE_STYLE_USAGE ( .BOTH. , #94059 ) ; +#1710 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#1711 = ORIENTED_EDGE ( 'NONE', *, *, #7514, .F. ) ; +#1712 = FILL_AREA_STYLE ('',( #18504 ) ) ; +#1713 = VECTOR ( 'NONE', #20268, 1000.000000000000000 ) ; +#1715 = EDGE_CURVE ( 'NONE', #57698, #57121, #29375, .T. ) ; +#1714 = SURFACE_STYLE_USAGE ( .BOTH. , #55347 ) ; +#1716 = SURFACE_STYLE_USAGE ( .BOTH. , #31823 ) ; +#1717 = PLANE ( 'NONE', #48845 ) ; +#1718 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13250 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90157, #65184, #89680 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1719 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#1720 = ORIENTED_EDGE ( 'NONE', *, *, #93036, .F. ) ; +#1722 = VERTEX_POINT ( 'NONE', #52883 ) ; +#1721 = ORIENTED_EDGE ( 'NONE', *, *, #31939, .T. ) ; +#1723 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #37776, #90377, #20428, #68874 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1724 = ORIENTED_EDGE ( 'NONE', *, *, #57004, .F. ) ; +#1725 = VECTOR ( 'NONE', #29884, 1000.000000000000000 ) ; +#1726 = EDGE_CURVE ( 'NONE', #39237, #95604, #5354, .T. ) ; +#1727 = FILL_AREA_STYLE ('',( #71145 ) ) ; +#1728 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1729 = ORIENTED_EDGE ( 'NONE', *, *, #74304, .F. ) ; +#1730 = ORIENTED_EDGE ( 'NONE', *, *, #93642, .F. ) ; +#1731 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1732 = SURFACE_SIDE_STYLE ('',( #71667 ) ) ; +#1733 = VERTEX_POINT ( 'NONE', #38054 ) ; +#1734 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1735 = ORIENTED_EDGE ( 'NONE', *, *, #51261, .F. ) ; +#1736 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#1737 = PLANE ( 'NONE', #48053 ) ; +#1738 = SURFACE_STYLE_USAGE ( .BOTH. , #9293 ) ; +#1739 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1740 = VECTOR ( 'NONE', #69708, 1000.000000000000000 ) ; +#1741 = ORIENTED_EDGE ( 'NONE', *, *, #40308, .F. ) ; +#1742 = PRESENTATION_STYLE_ASSIGNMENT (( #85467 ) ) ; +#1743 = VERTEX_POINT ( 'NONE', #28875 ) ; +#1744 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1745 = VECTOR ( 'NONE', #41059, 1000.000000000000000 ) ; +#1747 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1746 = SURFACE_SIDE_STYLE ('',( #71678 ) ) ; +#1748 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1749 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89609 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18267, #65780, #97856 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1750 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#1751 = VECTOR ( 'NONE', #27704, 1000.000000000000114 ) ; +#1752 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1753 = ORIENTED_EDGE ( 'NONE', *, *, #71697, .T. ) ; +#1755 = SURFACE_STYLE_FILL_AREA ( #56404 ) ; +#1754 = VECTOR ( 'NONE', #59247, 1000.000000000000000 ) ; +#1756 = ADVANCED_FACE ( 'NONE', ( #53873 ), #5849, .F. ) ; +#1758 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#1757 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#1759 = PLANE ( 'NONE', #19222 ) ; +#1760 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30345, #30870, #54383, #46684, #99231, #61047, #77847, #92145, #230, #62558, #21210, #55906, #1779, #79887, #78365, #8313, #9832, #50638, #39550 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.827722729374938181E-05, 3.540061502004491497E-05, 5.176356202143505262E-05, 6.750299826528590981E-05, 8.273623489609448006E-05, 9.765522892531060565E-05, 0.0001124576626364716376, 0.0001272425831096949279, 0.0001422599913927664861, 0.0001573908365776025030, 0.0001730496430735204219, 0.0001892507387656485287, 0.0002057214521072097335, 0.0002222442170891157219, 0.0002388674796421575363, 0.0002555440932686126325 ), + .UNSPECIFIED. ) ; +#1761 = AXIS2_PLACEMENT_3D ( 'NONE', #29930, #59134, #12547 ) ; +#1762 = CARTESIAN_POINT ( 'NONE', ( -0.9526471110344909565, -0.9920916311794309994, 0.8100000000000000533 ) ) ; +#1763 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81915 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50783, #66559, #23129 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1764 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1765 = ORIENTED_EDGE ( 'NONE', *, *, #1041, .T. ) ; +#1766 = LINE ( 'NONE', #62545, #87901 ) ; +#1767 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1768 = VERTEX_POINT ( 'NONE', #99241 ) ; +#1769 = PLANE ( 'NONE', #53033 ) ; +#1770 = FACE_OUTER_BOUND ( 'NONE', #71117, .T. ) ; +#1773 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1772 = SURFACE_STYLE_USAGE ( .BOTH. , #87518 ) ; +#1771 = SURFACE_STYLE_FILL_AREA ( #64050 ) ; +#1774 = LINE ( 'NONE', #48238, #48850 ) ; +#1775 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6569, 'distance_accuracy_value', 'NONE'); +#1776 = VECTOR ( 'NONE', #83846, 1000.000000000000000 ) ; +#1777 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#1778 = CARTESIAN_POINT ( 'NONE', ( 0.3732565376499660248, -1.295998480396600039, 0.8100000000000000533 ) ) ; +#1779 = CARTESIAN_POINT ( 'NONE', ( -1.222915055115519900, -1.432449005990839908, 0.8299999999999998490 ) ) ; +#1780 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1781 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1782 = ORIENTED_EDGE ( 'NONE', *, *, #89090, .F. ) ; +#1783 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.009999999999999998473, 1.250000000000000000 ) ) ; +#1784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1785 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#1786 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36041 ), #76753 ) ; +#1787 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1788 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1789 = SURFACE_SIDE_STYLE ('',( #79388 ) ) ; +#1790 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#1791 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1792 = PRESENTATION_STYLE_ASSIGNMENT (( #24282 ) ) ; +#1793 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1794 = CARTESIAN_POINT ( 'NONE', ( 3.277775499500048095, 5.988376499500051686, 0.8991599999999999593 ) ) ; +#1795 = VERTEX_POINT ( 'NONE', #60557 ) ; +#1796 = ORIENTED_EDGE ( 'NONE', *, *, #14398, .T. ) ; +#1797 = VECTOR ( 'NONE', #46469, 1000.000000000000000 ) ; +#1798 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.000000000000000000 ) ) ; +#1799 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1800 = CARTESIAN_POINT ( 'NONE', ( -1.038552480745770001, -1.181578794826660284, 0.8100000000000000533 ) ) ; +#1801 = ADVANCED_FACE ( 'NONE', ( #6336 ), #30879, .T. ) ; +#1802 = ORIENTED_EDGE ( 'NONE', *, *, #5903, .F. ) ; +#1803 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1804 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25941 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1218, #43540, #12328 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16393 ), #47409 ) ; +#1806 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1807 = ORIENTED_EDGE ( 'NONE', *, *, #45792, .T. ) ; +#1808 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#1809 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#1810 = AXIS2_PLACEMENT_3D ( 'NONE', #94664, #93637, #100705 ) ; +#1811 = CARTESIAN_POINT ( 'NONE', ( -1.237444333805499896, -1.426518300252259897, 0.8100000000000000533 ) ) ; +#1812 = PLANE ( 'NONE', #51223 ) ; +#1813 = ORIENTED_EDGE ( 'NONE', *, *, #13816, .T. ) ; +#1814 = SURFACE_SIDE_STYLE ('',( #71756 ) ) ; +#1815 = VECTOR ( 'NONE', #8166, 1000.000000000000000 ) ; +#1817 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#1816 = AXIS2_PLACEMENT_3D ( 'NONE', #45295, #46300, #60674 ) ; +#1818 = ADVANCED_FACE ( 'NONE', ( #39557 ), #54907, .T. ) ; +#1819 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65616, 'distance_accuracy_value', 'NONE'); +#1820 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38058 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53848, #73216, #19051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1821 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#1822 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1823 = CARTESIAN_POINT ( 'NONE', ( 7.386065750250000228, 3.435720750249999789, 0.8648700000000000276 ) ) ; +#1824 = AXIS2_PLACEMENT_3D ( 'NONE', #30952, #62133, #86074 ) ; +#1825 = ORIENTED_EDGE ( 'NONE', *, *, #7828, .F. ) ; +#1826 = FILL_AREA_STYLE ('',( #78913 ) ) ; +#1827 = ORIENTED_EDGE ( 'NONE', *, *, #26368, .T. ) ; +#1828 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.000000000000000000 ) ) ; +#1829 = CARTESIAN_POINT ( 'NONE', ( -1.370896901874992801, -1.085342039781137080, 0.8099999999999251132 ) ) ; +#1830 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#1831 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#1832 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1833 = EDGE_CURVE ( 'NONE', #92532, #54862, #77855, .T. ) ; +#1834 = AXIS2_PLACEMENT_3D ( 'NONE', #86735, #17770, #40789 ) ; +#1835 = AXIS2_PLACEMENT_3D ( 'NONE', #94976, #79713, #43892 ) ; +#1836 = VERTEX_POINT ( 'NONE', #55416 ) ; +#1838 = VERTEX_POINT ( 'NONE', #25767 ) ; +#1837 = PLANE ( 'NONE', #76936 ) ; +#1839 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41027, 'distance_accuracy_value', 'NONE'); +#1840 = FACE_OUTER_BOUND ( 'NONE', #58757, .T. ) ; +#1842 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1841 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#1843 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1844 = CARTESIAN_POINT ( 'NONE', ( -0.4535372177072710120, -0.9179759943635570352, 0.8299999999999999600 ) ) ; +#1845 = VERTEX_POINT ( 'NONE', #48247 ) ; +#1846 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1847 = FACE_OUTER_BOUND ( 'NONE', #18405, .T. ) ; +#1848 = PRESENTATION_STYLE_ASSIGNMENT (( #92702 ) ) ; +#1849 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34843 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50896, #64195, #56557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1850 = EDGE_LOOP ( 'NONE', ( #36845, #35680, #66717, #96094 ) ) ; +#1851 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1852 = ORIENTED_EDGE ( 'NONE', *, *, #27549, .T. ) ; +#1853 = VECTOR ( 'NONE', #87215, 1000.000000000000000 ) ; +#1854 = VERTEX_POINT ( 'NONE', #79376 ) ; +#1855 = PRESENTATION_STYLE_ASSIGNMENT (( #18131 ) ) ; +#1856 = EDGE_CURVE ( 'NONE', #97150, #70050, #40586, .T. ) ; +#1857 = FILL_AREA_STYLE ('',( #7901 ) ) ; +#1858 = FACE_OUTER_BOUND ( 'NONE', #15955, .T. ) ; +#1859 = ORIENTED_EDGE ( 'NONE', *, *, #33195, .F. ) ; +#1860 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1861 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#1862 = VERTEX_POINT ( 'NONE', #94148 ) ; +#1863 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1864 = ORIENTED_EDGE ( 'NONE', *, *, #23076, .T. ) ; +#1866 = EDGE_LOOP ( 'NONE', ( #65229, #29325, #93853, #63884 ) ) ; +#1865 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #47550, #55737, #57259, #87360 ), + ( #72057, #17400, #9174, #80234 ), + ( #32248, #48068, #1615, #79729 ), + ( #63413, #16883, #95496, #86357 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243628280, 0.6476030138606859721, 0.6476030138606859721, 0.8047378541243628280), + ( 0.8047378541243628280, 0.6476030138606859721, 0.6476030138606859721, 0.8047378541243628280), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#1867 = PLANE ( 'NONE', #6158 ) ; +#1868 = EDGE_CURVE ( 'NONE', #92789, #18897, #17556, .T. ) ; +#1870 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1869 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1871 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#1872 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 0.6999999999999999556, -13.40000000000000036 ) ) ; +#1873 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66710 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97534, #96528, #62674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#1874 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45827 ), #27979 ) ; +#1875 = SURFACE_STYLE_FILL_AREA ( #9928 ) ; +#1876 = CYLINDRICAL_SURFACE ( 'NONE', #49186, 0.1999999999999996503 ) ; +#1877 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.000000000000000000 ) ) ; +#1878 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100959 ) ; +#1879 = PRESENTATION_STYLE_ASSIGNMENT (( #47827 ) ) ; +#1880 = VERTEX_POINT ( 'NONE', #744 ) ; +#1881 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1882 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#1883 = VECTOR ( 'NONE', #43423, 1000.000000000000000 ) ; +#1884 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89912 ) ) ; +#1885 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#1886 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32859 ), #71775 ) ; +#1887 = FACE_OUTER_BOUND ( 'NONE', #90244, .T. ) ; +#1888 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1889 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#1890 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1891 = EDGE_LOOP ( 'NONE', ( #66124, #7108, #75706, #68964 ) ) ; +#1892 = AXIS2_PLACEMENT_3D ( 'NONE', #63419, #24628, #94999 ) ; +#1893 = LINE ( 'NONE', #95273, #78144 ) ; +#1894 = ADVANCED_FACE ( 'NONE', ( #70180 ), #87531, .F. ) ; +#1896 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89257, 'distance_accuracy_value', 'NONE'); +#1895 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#1897 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#1898 = LINE ( 'NONE', #33559, #40318 ) ; +#1899 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1900 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1901 = LINE ( 'NONE', #33035, #28532 ) ; +#1902 = EDGE_CURVE ( 'NONE', #82708, #58180, #11346, .T. ) ; +#1903 = EDGE_CURVE ( 'NONE', #21653, #22488, #67054, .T. ) ; +#1904 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999940048, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#1905 = FILL_AREA_STYLE ('',( #9964 ) ) ; +#1906 = FACE_OUTER_BOUND ( 'NONE', #17859, .T. ) ; +#1907 = SURFACE_STYLE_FILL_AREA ( #1404 ) ; +#1908 = VECTOR ( 'NONE', #48820, 1000.000000000000000 ) ; +#1909 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#1910 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#1911 = STYLED_ITEM ( 'NONE', ( #57456 ), #52520 ) ; +#1912 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1913 = SURFACE_STYLE_USAGE ( .BOTH. , #71865 ) ; +#1914 = EDGE_CURVE ( 'NONE', #23955, #32073, #89829, .T. ) ; +#1915 = ORIENTED_EDGE ( 'NONE', *, *, #73971, .F. ) ; +#1916 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1917 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#1918 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#1919 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#1920 = STYLED_ITEM ( 'NONE', ( #54915 ), #51893 ) ; +#1921 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#1922 = LINE ( 'NONE', #28297, #23717 ) ; +#1923 = AXIS2_PLACEMENT_3D ( 'NONE', #45724, #99770, #76915 ) ; +#1924 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#1925 = ORIENTED_EDGE ( 'NONE', *, *, #76245, .F. ) ; +#1926 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#1927 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1928 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#1929 = EDGE_CURVE ( 'NONE', #78606, #26813, #50280, .T. ) ; +#1930 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4850000000000001532, 0.2458578643762690530 ) ) ; +#1931 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #9668, #9166, #40922, #57254 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1932 = FILL_AREA_STYLE_COLOUR ( '', #29018 ) ; +#1933 = EDGE_LOOP ( 'NONE', ( #50226, #15728, #16335, #80092 ) ) ; +#1934 = EDGE_CURVE ( 'NONE', #35769, #41162, #50776, .T. ) ; +#1935 = ORIENTED_EDGE ( 'NONE', *, *, #88813, .T. ) ; +#1936 = STYLED_ITEM ( 'NONE', ( #41391 ), #34076 ) ; +#1937 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#1938 = ORIENTED_EDGE ( 'NONE', *, *, #17278, .F. ) ; +#1939 = PRESENTATION_STYLE_ASSIGNMENT (( #80072 ) ) ; +#1940 = PRESENTATION_STYLE_ASSIGNMENT (( #73410 ) ) ; +#1941 = SURFACE_STYLE_FILL_AREA ( #24447 ) ; +#1942 = FACE_OUTER_BOUND ( 'NONE', #64873, .T. ) ; +#1943 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#1944 = VECTOR ( 'NONE', #17319, 1000.000000000000000 ) ; +#1945 = EDGE_CURVE ( 'NONE', #90091, #94847, #3277, .T. ) ; +#1946 = AXIS2_PLACEMENT_3D ( 'NONE', #25917, #80540, #58586 ) ; +#1947 = SHAPE_DEFINITION_REPRESENTATION ( #37661, #98962 ) ; +#1948 = LINE ( 'NONE', #33089, #13359 ) ; +#1949 = EDGE_CURVE ( 'NONE', #74029, #37111, #43562, .T. ) ; +#1951 = VERTEX_POINT ( 'NONE', #18574 ) ; +#1950 = ORIENTED_EDGE ( 'NONE', *, *, #99862, .T. ) ; +#1952 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#1953 = VECTOR ( 'NONE', #50831, 1000.000000000000000 ) ; +#1954 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52463 ), #86707 ) ; +#1955 = ORIENTED_EDGE ( 'NONE', *, *, #41018, .T. ) ; +#1956 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1957 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87139, 'distance_accuracy_value', 'NONE'); +#1958 = VECTOR ( 'NONE', #53444, 1000.000000000000114 ) ; +#1959 = CARTESIAN_POINT ( 'NONE', ( 1.810234811980210079, -1.482878949593630091, 0.8299999999999999600 ) ) ; +#1961 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#1960 = CARTESIAN_POINT ( 'NONE', ( 0.5421186041101929698, -1.033429037169790066, 0.8299999999999999600 ) ) ; +#1962 = ORIENTED_EDGE ( 'NONE', *, *, #55244, .F. ) ; +#1963 = AXIS2_PLACEMENT_3D ( 'NONE', #53599, #61779, #62276 ) ; +#1964 = FILL_AREA_STYLE ('',( #56619 ) ) ; +#1965 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92446, #45965, #54181, #62872 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#1966 = ORIENTED_EDGE ( 'NONE', *, *, #47414, .T. ) ; +#1967 = FACE_OUTER_BOUND ( 'NONE', #54469, .T. ) ; +#1968 = STYLED_ITEM ( 'NONE', ( #75493 ), #66387 ) ; +#1969 = VERTEX_POINT ( 'NONE', #34941 ) ; +#1970 = CYLINDRICAL_SURFACE ( 'NONE', #68234, 0.09999999999999999167 ) ; +#1971 = VERTEX_POINT ( 'NONE', #27277 ) ; +#1972 = ORIENTED_EDGE ( 'NONE', *, *, #96754, .T. ) ; +#1973 = SURFACE_STYLE_USAGE ( .BOTH. , #96871 ) ; +#1974 = EDGE_CURVE ( 'NONE', #80592, #80846, #72716, .T. ) ; +#1975 = CARTESIAN_POINT ( 'NONE', ( -0.8909255146275300019, 0.6567860187191519872, 0.8299999999999999600 ) ) ; +#1976 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#1977 = ORIENTED_EDGE ( 'NONE', *, *, #86445, .T. ) ; +#1978 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#1979 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#1980 = CARTESIAN_POINT ( 'NONE', ( -0.2353471038102170343, -0.9412361261466359874, 0.8299999999999999600 ) ) ; +#1981 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.600000000000000089, -11.36999999999999922 ) ) ; +#1982 = ORIENTED_EDGE ( 'NONE', *, *, #58411, .T. ) ; +#1984 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#1983 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.8999999999999990230, -0.02000000000001679948 ) ) ; +#1986 = ORIENTED_EDGE ( 'NONE', *, *, #13945, .T. ) ; +#1985 = AXIS2_PLACEMENT_3D ( 'NONE', #74260, #32945, #87565 ) ; +#1987 = ORIENTED_EDGE ( 'NONE', *, *, #63899, .T. ) ; +#1988 = ADVANCED_FACE ( 'NONE', ( #98127 ), #4275, .T. ) ; +#1990 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1989 = SURFACE_STYLE_FILL_AREA ( #47941 ) ; +#1991 = CARTESIAN_POINT ( 'NONE', ( 1.731329805614240325, -1.441250752426249893, 0.8300000000000002931 ) ) ; +#1992 = DIRECTION ( 'NONE', ( 4.640777529015779698E-48, 0.000000000000000000, -1.000000000000000000 ) ) ; +#1993 = EDGE_CURVE ( 'NONE', #61884, #69965, #65540, .T. ) ; +#1995 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#1994 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#1996 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37944, 'distance_accuracy_value', 'NONE'); +#1997 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#1998 = ORIENTED_EDGE ( 'NONE', *, *, #36581, .T. ) ; +#1999 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#2000 = ORIENTED_EDGE ( 'NONE', *, *, #41131, .F. ) ; +#2001 = EDGE_CURVE ( 'NONE', #47892, #5265, #65060, .T. ) ; +#2002 = STYLED_ITEM ( 'NONE', ( #27218 ), #82086 ) ; +#2003 = AXIS2_PLACEMENT_3D ( 'NONE', #53184, #52685, #22524 ) ; +#2004 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -3.183217578417443114E-17, 0.2499999999999998890 ) ) ; +#2005 = PLANE ( 'NONE', #66558 ) ; +#2006 = CYLINDRICAL_SURFACE ( 'NONE', #65922, 0.05000000000000002359 ) ; +#2007 = SURFACE_STYLE_USAGE ( .BOTH. , #2512 ) ; +#2008 = FILL_AREA_STYLE_COLOUR ( '', #23869 ) ; +#2009 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#2010 = SURFACE_STYLE_USAGE ( .BOTH. , #41828 ) ; +#2012 = AXIS2_PLACEMENT_3D ( 'NONE', #55404, #95649, #24255 ) ; +#2011 = FILL_AREA_STYLE_COLOUR ( '', #8532 ) ; +#2013 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2014 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2015 = SURFACE_SIDE_STYLE ('',( #86258 ) ) ; +#2016 = CYLINDRICAL_SURFACE ( 'NONE', #30350, 0.05000000000000012768 ) ; +#2017 = EDGE_CURVE ( 'NONE', #52069, #45112, #33939, .T. ) ; +#2018 = AXIS2_PLACEMENT_3D ( 'NONE', #58921, #11317, #81882 ) ; +#2019 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94983 ) ) ; +#2020 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2021 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2022 = PRESENTATION_STYLE_ASSIGNMENT (( #95411 ) ) ; +#2023 = LINE ( 'NONE', #63334, #74770 ) ; +#2024 = VECTOR ( 'NONE', #67112, 1000.000000000000000 ) ; +#2025 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#2026 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#2027 = VECTOR ( 'NONE', #60796, 1000.000000000000000 ) ; +#2028 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15002 ), #42845 ) ; +#2029 = EDGE_LOOP ( 'NONE', ( #95063, #34246, #72410, #78078 ) ) ; +#2030 = SURFACE_SIDE_STYLE ('',( #40343 ) ) ; +#2031 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70524 ), #93301 ) ; +#2032 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56668, 'distance_accuracy_value', 'NONE'); +#2033 = ADVANCED_FACE ( 'NONE', ( #38435 ), #52763, .F. ) ; +#2034 = ORIENTED_EDGE ( 'NONE', *, *, #59877, .T. ) ; +#2035 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28743, 'distance_accuracy_value', 'NONE'); +#2036 = CARTESIAN_POINT ( 'NONE', ( 0.5854301948051948701, 0.6899999999999999467, 0.2077922077922076116 ) ) ; +#2037 = PRESENTATION_STYLE_ASSIGNMENT (( #89316 ) ) ; +#2038 = ADVANCED_FACE ( 'NONE', ( #59450 ), #14894, .F. ) ; +#2039 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, 3.099999999999969891, 0.000000000000000000 ) ) ; +#2040 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2808578643762690286, -0.1500000000000000222 ) ) ; +#2041 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2042 = STYLED_ITEM ( 'NONE', ( #63957 ), #25497 ) ; +#2043 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.123820061220055511, 0.000000000000000000 ) ) ; +#2044 = ORIENTED_EDGE ( 'NONE', *, *, #56580, .F. ) ; +#2045 = SURFACE_SIDE_STYLE ('',( #8585 ) ) ; +#2046 = EDGE_LOOP ( 'NONE', ( #73099, #31574, #36499, #65901 ) ) ; +#2047 = LINE ( 'NONE', #87809, #19419 ) ; +#2048 = STYLED_ITEM ( 'NONE', ( #24094 ), #70292 ) ; +#2049 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8089, 'distance_accuracy_value', 'NONE'); +#2050 = PRESENTATION_STYLE_ASSIGNMENT (( #11114 ) ) ; +#2051 = SURFACE_SIDE_STYLE ('',( #25052 ) ) ; +#2052 = LINE ( 'NONE', #38835, #23768 ) ; +#2053 = FACE_OUTER_BOUND ( 'NONE', #61225, .T. ) ; +#2054 = ADVANCED_FACE ( 'NONE', ( #45529 ), #5732, .T. ) ; +#2055 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#2056 = PLANE ( 'NONE', #74674 ) ; +#2057 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2058 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#2059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44942 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59858, #83807, #29658 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2060 = ORIENTED_EDGE ( 'NONE', *, *, #73158, .T. ) ; +#2061 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#2062 = FACE_OUTER_BOUND ( 'NONE', #61983, .T. ) ; +#2063 = ORIENTED_EDGE ( 'NONE', *, *, #79443, .T. ) ; +#2064 = ADVANCED_FACE ( 'NONE', ( #47601 ), #15414, .T. ) ; +#2065 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#2066 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2067 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2068 = VERTEX_POINT ( 'NONE', #79771 ) ; +#2069 = LINE ( 'NONE', #40881, #91696 ) ; +#2070 = VECTOR ( 'NONE', #28102, 1000.000000000000000 ) ; +#2071 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#2072 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2073 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#2074 = EDGE_CURVE ( 'NONE', #82841, #76154, #63460, .T. ) ; +#2075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2076 = FACE_OUTER_BOUND ( 'NONE', #47705, .T. ) ; +#2077 = FILL_AREA_STYLE_COLOUR ( '', #11413 ) ; +#2078 = FILL_AREA_STYLE_COLOUR ( '', #44753 ) ; +#2079 = ADVANCED_FACE ( 'NONE', ( #8698 ), #9719, .T. ) ; +#2081 = ORIENTED_EDGE ( 'NONE', *, *, #25336, .T. ) ; +#2080 = ORIENTED_EDGE ( 'NONE', *, *, #40837, .F. ) ; +#2082 = PRESENTATION_STYLE_ASSIGNMENT (( #72029 ) ) ; +#2083 = VERTEX_POINT ( 'NONE', #23122 ) ; +#2084 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -1.900000000000000133, -0.02000000000000000042 ) ) ; +#2085 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2086 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26507 ), #370 ) ; +#2087 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.100000000000000311, 1.048695503451053346E-76 ) ) ; +#2088 = EDGE_LOOP ( 'NONE', ( #79842, #67067, #84769, #100151 ) ) ; +#2089 = ORIENTED_EDGE ( 'NONE', *, *, #31323, .T. ) ; +#2090 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #45284, #92273, #22333, #76457 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2091 = LINE ( 'NONE', #17378, #22086 ) ; +#2092 = LINE ( 'NONE', #88854, #64265 ) ; +#2093 = AXIS2_PLACEMENT_3D ( 'NONE', #41265, #56602, #72370 ) ; +#2094 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13358 ), #60769 ) ; +#2095 = VECTOR ( 'NONE', #64493, 1000.000000000000000 ) ; +#2097 = SURFACE_STYLE_FILL_AREA ( #72040 ) ; +#2096 = FILL_AREA_STYLE ('',( #10136 ) ) ; +#2098 = ORIENTED_EDGE ( 'NONE', *, *, #76131, .T. ) ; +#2099 = ORIENTED_EDGE ( 'NONE', *, *, #35912, .T. ) ; +#2100 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59011 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43033, #59907, #66519 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2101 = ORIENTED_EDGE ( 'NONE', *, *, #67018, .T. ) ; +#2102 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51018 ), #77070 ) ; +#2103 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2499999999999997780, -0.6999999999999999556 ) ) ; +#2104 = EDGE_CURVE ( 'NONE', #76986, #79461, #85385, .T. ) ; +#2105 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80385 ), #98215 ) ; +#2107 = VERTEX_POINT ( 'NONE', #38934 ) ; +#2106 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.700000000000000178, 0.000000000000000000 ) ) ; +#2108 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#2109 = STYLED_ITEM ( 'NONE', ( #77050 ), #11448 ) ; +#2110 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.2999999999999990452, 0.8299999999999999600 ) ) ; +#2111 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2112 = ORIENTED_EDGE ( 'NONE', *, *, #71548, .F. ) ; +#2113 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999918510, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#2114 = ORIENTED_EDGE ( 'NONE', *, *, #64133, .T. ) ; +#2115 = EDGE_CURVE ( 'NONE', #42116, #5281, #35071, .T. ) ; +#2116 = PRESENTATION_STYLE_ASSIGNMENT (( #72058 ) ) ; +#2117 = EDGE_CURVE ( 'NONE', #82544, #11562, #70054, .T. ) ; +#2118 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#2119 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2120 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2122 = FILL_AREA_STYLE_COLOUR ( '', #59705 ) ; +#2121 = LINE ( 'NONE', #10162, #92079 ) ; +#2123 = CARTESIAN_POINT ( 'NONE', ( 1.592056040834880060, -1.030915998478540097, 0.8299999999999990719 ) ) ; +#2124 = VERTEX_POINT ( 'NONE', #41465 ) ; +#2125 = CARTESIAN_POINT ( 'NONE', ( 9.231614875125044861, 3.725634875125043877, 0.8648700000000000276 ) ) ; +#2126 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2127 = ORIENTED_EDGE ( 'NONE', *, *, #8307, .T. ) ; +#2128 = ADVANCED_FACE ( 'NONE', ( #17932 ), #64936, .F. ) ; +#2129 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#2130 = LINE ( 'NONE', #80247, #9247 ) ; +#2131 = LINE ( 'NONE', #72074, #91962 ) ; +#2132 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2133 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#2134 = CARTESIAN_POINT ( 'NONE', ( 1.688395628309256306E-17, 0.8200000000000000622, -0.1378679656440357226 ) ) ; +#2135 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99992 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26557, #33206, #42381 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2137 = SURFACE_SIDE_STYLE ('',( #8175 ) ) ; +#2136 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.499999999999989786, 0.1829999999999999960 ) ) ; +#2138 = SURFACE_STYLE_USAGE ( .BOTH. , #9697 ) ; +#2139 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#2140 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2141 = VECTOR ( 'NONE', #52264, 1000.000000000000000 ) ; +#2142 = VECTOR ( 'NONE', #92185, 1000.000000000000000 ) ; +#2143 = FILL_AREA_STYLE ('',( #15903 ) ) ; +#2144 = PRESENTATION_STYLE_ASSIGNMENT (( #10181 ) ) ; +#2145 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2146 = VECTOR ( 'NONE', #79037, 1000.000000000000000 ) ; +#2147 = ADVANCED_FACE ( 'NONE', ( #88925 ), #50646, .F. ) ; +#2148 = ORIENTED_EDGE ( 'NONE', *, *, #10753, .F. ) ; +#2149 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4699999999999999734, 0.000000000000000000 ) ) ; +#2150 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2151 = VECTOR ( 'NONE', #80904, 1000.000000000000114 ) ; +#2152 = CIRCLE ( 'NONE', #59255, 0.2000000000000005107 ) ; +#2153 = FILL_AREA_STYLE ('',( #55284 ) ) ; +#2155 = ORIENTED_EDGE ( 'NONE', *, *, #73346, .F. ) ; +#2154 = VECTOR ( 'NONE', #77768, 1000.000000000000000 ) ; +#2156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2157 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.90000000000000036, 0.000000000000000000 ) ) ; +#2158 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2159 = EDGE_CURVE ( 'NONE', #22729, #97577, #81786, .T. ) ; +#2160 = VECTOR ( 'NONE', #44606, 1000.000000000000000 ) ; +#2161 = AXIS2_PLACEMENT_3D ( 'NONE', #81778, #72572, #10709 ) ; +#2162 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2163 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#2165 = CARTESIAN_POINT ( 'NONE', ( -0.9900422999955440506, -1.351484773706350007, 0.8300000000000001821 ) ) ; +#2164 = AXIS2_PLACEMENT_3D ( 'NONE', #38279, #92373, #29595 ) ; +#2167 = VECTOR ( 'NONE', #39716, 1000.000000000000000 ) ; +#2166 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2168 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32339, 'distance_accuracy_value', 'NONE'); +#2169 = STYLED_ITEM ( 'NONE', ( #74527 ), #96898 ) ; +#2170 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.323820061220084998, -0.02000000000000000042 ) ) ; +#2171 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 1.149999999999999911, 0.000000000000000000 ) ) ; +#2172 = ORIENTED_EDGE ( 'NONE', *, *, #72649, .T. ) ; +#2173 = ORIENTED_EDGE ( 'NONE', *, *, #14644, .T. ) ; +#2174 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2175 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21463, 'distance_accuracy_value', 'NONE'); +#2176 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50877, 'distance_accuracy_value', 'NONE'); +#2177 = VECTOR ( 'NONE', #2282, 1000.000000000000114 ) ; +#2178 = FACE_OUTER_BOUND ( 'NONE', #33266, .T. ) ; +#2179 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.1000000000000000056, -12.01999999999999957 ) ) ; +#2180 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#2181 = PRESENTATION_STYLE_ASSIGNMENT (( #89450 ) ) ; +#2182 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2183 = PRESENTATION_STYLE_ASSIGNMENT (( #72123 ) ) ; +#2184 = ORIENTED_EDGE ( 'NONE', *, *, #49652, .F. ) ; +#2185 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -0.2000000000000000111 ) ) ; +#2186 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8100000000001583711 ) ) ; +#2187 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#2188 = ORIENTED_EDGE ( 'NONE', *, *, #49157, .F. ) ; +#2189 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69556 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88081, #80427, #26309 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2190 = FACE_OUTER_BOUND ( 'NONE', #3574, .T. ) ; +#2191 = ORIENTED_EDGE ( 'NONE', *, *, #69105, .T. ) ; +#2192 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2193 = SURFACE_SIDE_STYLE ('',( #24695 ) ) ; +#2194 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2195 = PLANE ( 'NONE', #75265 ) ; +#2196 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000004441, -0.1400000000000000411 ) ) ; +#2197 = LINE ( 'NONE', #42507, #90407 ) ; +#2198 = ADVANCED_FACE ( 'NONE', ( #65420 ), #89421, .T. ) ; +#2199 = VERTEX_POINT ( 'NONE', #39771 ) ; +#2200 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2201 = FILL_AREA_STYLE ('',( #48672 ) ) ; +#2202 = ORIENTED_EDGE ( 'NONE', *, *, #27602, .F. ) ; +#2203 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86784, #92401, #8067, #40334 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2204 = AXIS2_PLACEMENT_3D ( 'NONE', #21643, #52315, #98658 ) ; +#2205 = EDGE_CURVE ( 'NONE', #83324, #45383, #95958, .T. ) ; +#2206 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.4245906043549200204, 0.000000000000000000 ) ) ; +#2207 = ORIENTED_EDGE ( 'NONE', *, *, #23555, .F. ) ; +#2208 = FACE_OUTER_BOUND ( 'NONE', #71083, .T. ) ; +#2209 = STYLED_ITEM ( 'NONE', ( #62546 ), #88215 ) ; +#2210 = CARTESIAN_POINT ( 'NONE', ( -0.4484724165379589955, -1.115587024626630175, 0.8299999999999999600 ) ) ; +#2211 = FILL_AREA_STYLE ('',( #87969 ) ) ; +#2212 = SURFACE_STYLE_FILL_AREA ( #72151 ) ; +#2213 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#2214 = ORIENTED_EDGE ( 'NONE', *, *, #27893, .F. ) ; +#2216 = EDGE_LOOP ( 'NONE', ( #10860, #16031, #25033, #15584 ) ) ; +#2215 = VERTEX_POINT ( 'NONE', #62767 ) ; +#2217 = FACE_OUTER_BOUND ( 'NONE', #11151, .T. ) ; +#2218 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58469, #32050, #94301 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2219 = AXIS2_PLACEMENT_3D ( 'NONE', #86443, #71119, #55818 ) ; +#2220 = ORIENTED_EDGE ( 'NONE', *, *, #98296, .F. ) ; +#2221 = EDGE_CURVE ( 'NONE', #61084, #3614, #47426, .T. ) ; +#2222 = ORIENTED_EDGE ( 'NONE', *, *, #9110, .F. ) ; +#2224 = EDGE_LOOP ( 'NONE', ( #97190, #52746, #15882, #90560 ) ) ; +#2223 = CARTESIAN_POINT ( 'NONE', ( -0.7175470460908950354, 1.464404984293220080, 0.8100000000000000533 ) ) ; +#2227 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2226 = FILL_AREA_STYLE ('',( #31835 ) ) ; +#2225 = VECTOR ( 'NONE', #18313, 1000.000000000000000 ) ; +#2228 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64173 ) ) ; +#2229 = SURFACE_STYLE_USAGE ( .BOTH. , #78804 ) ; +#2230 = VERTEX_POINT ( 'NONE', #16749 ) ; +#2231 = LINE ( 'NONE', #3229, #11325 ) ; +#2233 = CARTESIAN_POINT ( 'NONE', ( 1.765390738874589971, -1.428263396816370046, 0.8099999999999997202 ) ) ; +#2232 = VECTOR ( 'NONE', #32552, 1000.000000000000000 ) ; +#2234 = EDGE_LOOP ( 'NONE', ( #98054, #45105, #27618, #23117 ) ) ; +#2235 = EDGE_CURVE ( 'NONE', #84311, #63967, #79594, .T. ) ; +#2236 = DIRECTION ( 'NONE', ( 0.7071071146859688739, 0.7071064476869688420, -0.000000000000000000 ) ) ; +#2237 = AXIS2_PLACEMENT_3D ( 'NONE', #4693, #70501, #32224 ) ; +#2238 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96715 ) ) ; +#2239 = PRESENTATION_STYLE_ASSIGNMENT (( #85969 ) ) ; +#2240 = ORIENTED_EDGE ( 'NONE', *, *, #39554, .F. ) ; +#2241 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2242 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44617 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37660, #54504, #91746 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2243 = VECTOR ( 'NONE', #33982, 1000.000000000000000 ) ; +#2245 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8648700000000000276 ) ) ; +#2244 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2246 = ADVANCED_FACE ( 'NONE', ( #72403 ), #32627, .T. ) ; +#2247 = VECTOR ( 'NONE', #24143, 1000.000000000000000 ) ; +#2248 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.8999999999999999112, -0.02000000000000000042 ) ) ; +#2249 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2250 = SURFACE_STYLE_USAGE ( .BOTH. , #57392 ) ; +#2251 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #64914, #34803, #96023, #10692, #3131, #12724, #53116, #98477 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000000000, 0.5000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2252 = EDGE_CURVE ( 'NONE', #84782, #48204, #8521, .T. ) ; +#2254 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2253 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2255 = SURFACE_STYLE_FILL_AREA ( #73693 ) ; +#2256 = LINE ( 'NONE', #3747, #65937 ) ; +#2257 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34836 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65459, #72137, #86955 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2258 = CARTESIAN_POINT ( 'NONE', ( -1.050422986827179939, -0.9018902076549559776, 0.8100000000000000533 ) ) ; +#2259 = CARTESIAN_POINT ( 'NONE', ( 1.063743438223609949, -0.9165513359838141083, 0.8299999999999999600 ) ) ; +#2260 = ORIENTED_EDGE ( 'NONE', *, *, #14850, .F. ) ; +#2261 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2262 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2263 = ADVANCED_FACE ( 'NONE', ( #33118 ), #965, .T. ) ; +#2264 = LINE ( 'NONE', #88521, #31560 ) ; +#2265 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#2266 = EDGE_CURVE ( 'NONE', #46722, #80338, #25442, .T. ) ; +#2267 = CYLINDRICAL_SURFACE ( 'NONE', #2706, 0.05000000000000012768 ) ; +#2268 = ORIENTED_EDGE ( 'NONE', *, *, #44517, .F. ) ; +#2269 = CARTESIAN_POINT ( 'NONE', ( -0.9276048691944630553, -1.263266231710209908, 0.8300000000000002931 ) ) ; +#2270 = SURFACE_SIDE_STYLE ('',( #33417 ) ) ; +#2273 = FACE_OUTER_BOUND ( 'NONE', #7293, .T. ) ; +#2272 = CARTESIAN_POINT ( 'NONE', ( 10.66704099999999933, 4.241822999999999233, 0.8991599999999999593 ) ) ; +#2271 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2274 = PRESENTATION_STYLE_ASSIGNMENT (( #58935 ) ) ; +#2275 = EDGE_CURVE ( 'NONE', #48405, #4472, #34610, .T. ) ; +#2277 = EDGE_CURVE ( 'NONE', #69719, #55510, #96335, .T. ) ; +#2276 = CARTESIAN_POINT ( 'NONE', ( 0.2550745812975909743, -1.387940725880749904, 0.8100000000000000533 ) ) ; +#2278 = CARTESIAN_POINT ( 'NONE', ( -0.2166666666666656749, 3.099999999999980549, 0.000000000000000000 ) ) ; +#2279 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#2280 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38979, #78780, #85429 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2281 = ORIENTED_EDGE ( 'NONE', *, *, #95817, .F. ) ; +#2282 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#2283 = FILL_AREA_STYLE ('',( #41090 ) ) ; +#2284 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#2285 = FACE_OUTER_BOUND ( 'NONE', #23744, .T. ) ; +#2286 = EDGE_CURVE ( 'NONE', #82725, #80839, #3933, .T. ) ; +#2287 = VECTOR ( 'NONE', #96149, 1000.000000000000114 ) ; +#2288 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.5000000000000017764, 0.8299999999999999600 ) ) ; +#2289 = LINE ( 'NONE', #10850, #86000 ) ; +#2290 = SURFACE_STYLE_FILL_AREA ( #19082 ) ; +#2291 = LINE ( 'NONE', #79385, #93068 ) ; +#2292 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2293 = FACE_OUTER_BOUND ( 'NONE', #94166, .T. ) ; +#2294 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #507 ) ) ; +#2295 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2296 = LINE ( 'NONE', #87542, #95654 ) ; +#2297 = ADVANCED_FACE ( 'NONE', ( #57095 ), #27438, .T. ) ; +#2298 = LINE ( 'NONE', #78376, #84911 ) ; +#2299 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000019540, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#2300 = LINE ( 'NONE', #9356, #27580 ) ; +#2301 = ORIENTED_EDGE ( 'NONE', *, *, #87099, .T. ) ; +#2302 = ORIENTED_EDGE ( 'NONE', *, *, #84907, .T. ) ; +#2303 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35652, 'distance_accuracy_value', 'NONE'); +#2304 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12131, 'distance_accuracy_value', 'NONE'); +#2305 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2306 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2808578643762690286, 0.1434314575050761598 ) ) ; +#2307 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2308 = LINE ( 'NONE', #1798, #25964 ) ; +#2309 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73463 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87170, #76981, #63209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2310 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55161, #70949, #24523, #50516 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2312 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2313 = SURFACE_SIDE_STYLE ('',( #41614 ) ) ; +#2314 = ORIENTED_EDGE ( 'NONE', *, *, #33391, .F. ) ; +#2315 = SURFACE_SIDE_STYLE ('',( #96201 ) ) ; +#2316 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39398, 'distance_accuracy_value', 'NONE'); +#2318 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10217 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33234, #80214, #40910 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2317 = FILL_AREA_STYLE_COLOUR ( '', #99806 ) ; +#2319 = VERTEX_POINT ( 'NONE', #96837 ) ; +#2320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2321 = VECTOR ( 'NONE', #30854, 1000.000000000000000 ) ; +#2322 = PLANE ( 'NONE', #77781 ) ; +#2323 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53633 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31431, #55951, #87076 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2324 = SURFACE_STYLE_USAGE ( .BOTH. , #79420 ) ; +#2325 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#2326 = ORIENTED_EDGE ( 'NONE', *, *, #78119, .F. ) ; +#2327 = VECTOR ( 'NONE', #99897, 1000.000000000000000 ) ; +#2328 = SURFACE_STYLE_FILL_AREA ( #79428 ) ; +#2329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67501, 'distance_accuracy_value', 'NONE'); +#2330 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2331 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2332 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2333 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30752 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79187, #16860, #55721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2334 = EDGE_CURVE ( 'NONE', #48182, #83845, #72891, .T. ) ; +#2335 = ORIENTED_EDGE ( 'NONE', *, *, #43902, .T. ) ; +#2336 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999645, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#2337 = SURFACE_STYLE_USAGE ( .BOTH. , #9396 ) ; +#2338 = VECTOR ( 'NONE', #61847, 1000.000000000000000 ) ; +#2339 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#2340 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2341 = SURFACE_STYLE_USAGE ( .BOTH. , #94713 ) ; +#2342 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72417 ), #52835 ) ; +#2343 = CIRCLE ( 'NONE', #80632, 0.009999999999999998473 ) ; +#2344 = ORIENTED_EDGE ( 'NONE', *, *, #12806, .T. ) ; +#2346 = ORIENTED_EDGE ( 'NONE', *, *, #6759, .T. ) ; +#2345 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8648700000000000276 ) ) ; +#2347 = PRESENTATION_STYLE_ASSIGNMENT (( #10387 ) ) ; +#2348 = FACE_OUTER_BOUND ( 'NONE', #51801, .T. ) ; +#2349 = AXIS2_PLACEMENT_3D ( 'NONE', #6137, #27707, #34 ) ; +#2350 = FACE_OUTER_BOUND ( 'NONE', #48750, .T. ) ; +#2351 = ORIENTED_EDGE ( 'NONE', *, *, #47070, .F. ) ; +#2352 = STYLED_ITEM ( 'NONE', ( #17307 ), #87516 ) ; +#2353 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2354 = SURFACE_STYLE_FILL_AREA ( #49836 ) ; +#2355 = EDGE_LOOP ( 'NONE', ( #75435, #43247, #90811, #91695 ) ) ; +#2356 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#2357 = ORIENTED_EDGE ( 'NONE', *, *, #58490, .T. ) ; +#2358 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52855 ), #87113 ) ; +#2359 = VERTEX_POINT ( 'NONE', #88701 ) ; +#2360 = LINE ( 'NONE', #2865, #77212 ) ; +#2361 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2362 = AXIS2_PLACEMENT_3D ( 'NONE', #728, #31884, #63049 ) ; +#2363 = VERTEX_POINT ( 'NONE', #87703 ) ; +#2364 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2365 = CIRCLE ( 'NONE', #44735, 1.383450513437169960 ) ; +#2366 = VECTOR ( 'NONE', #48266, 1000.000000000000000 ) ; +#2367 = ORIENTED_EDGE ( 'NONE', *, *, #49074, .T. ) ; +#2368 = CYLINDRICAL_SURFACE ( 'NONE', #29853, 0.05000000000000012768 ) ; +#2369 = EDGE_LOOP ( 'NONE', ( #45991, #60651, #21778, #57769 ) ) ; +#2370 = EDGE_LOOP ( 'NONE', ( #67383, #80157, #44839, #76293 ) ) ; +#2371 = PLANE ( 'NONE', #30686 ) ; +#2372 = VECTOR ( 'NONE', #87414, 1000.000000000000000 ) ; +#2374 = DIRECTION ( 'NONE', ( 0.7071045084557434635, 0.7071090539100467476, 0.000000000000000000 ) ) ; +#2373 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2375 = CARTESIAN_POINT ( 'NONE', ( -0.9897739841320261078, -1.331314275383060020, 0.8299999999999999600 ) ) ; +#2376 = LINE ( 'NONE', #20055, #66237 ) ; +#2377 = SURFACE_STYLE_USAGE ( .BOTH. , #88627 ) ; +#2379 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2378 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80588 ) ) ; +#2380 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85258 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38673, #52499, #29004 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2381 = PRESENTATION_STYLE_ASSIGNMENT (( #3382 ) ) ; +#2382 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2383 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#2384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44429 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76142, #53177, #21024 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2385 = VERTEX_POINT ( 'NONE', #58606 ) ; +#2386 = PRESENTATION_STYLE_ASSIGNMENT (( #41193 ) ) ; +#2387 = CARTESIAN_POINT ( 'NONE', ( 1.238543046823479932, -1.444732071753930036, 0.8299999999999994049 ) ) ; +#2388 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2389 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#2390 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23588 ) ) ; +#2391 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2392 = EDGE_CURVE ( 'NONE', #78342, #37515, #18738, .T. ) ; +#2393 = AXIS2_PLACEMENT_3D ( 'NONE', #41933, #3115, #27125 ) ; +#2394 = SURFACE_STYLE_USAGE ( .BOTH. , #80010 ) ; +#2395 = LINE ( 'NONE', #82019, #10898 ) ; +#2396 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2397 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#2398 = ORIENTED_EDGE ( 'NONE', *, *, #24053, .F. ) ; +#2399 = SURFACE_STYLE_FILL_AREA ( #87156 ) ; +#2400 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.061746575926969971, 0.8299999999999999600 ) ) ; +#2401 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49640 ) ) ; +#2402 = SURFACE_STYLE_FILL_AREA ( #65177 ) ; +#2403 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78535, 'distance_accuracy_value', 'NONE'); +#2404 = FACE_OUTER_BOUND ( 'NONE', #36537, .T. ) ; +#2405 = SURFACE_STYLE_FILL_AREA ( #81035 ) ; +#2406 = SURFACE_STYLE_FILL_AREA ( #95282 ) ; +#2407 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#2408 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2409 = EDGE_CURVE ( 'NONE', #39861, #72808, #49928, .T. ) ; +#2410 = PLANE ( 'NONE', #88289 ) ; +#2411 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, 0.000000000000000000 ) ) ; +#2412 = LINE ( 'NONE', #71338, #96022 ) ; +#2413 = PRESENTATION_STYLE_ASSIGNMENT (( #72339 ) ) ; +#2414 = VECTOR ( 'NONE', #9325, 1000.000000000000000 ) ; +#2415 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2416 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2417 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2418 = VECTOR ( 'NONE', #42853, 1000.000000000000000 ) ; +#2419 = STYLED_ITEM ( 'NONE', ( #64908 ), #53783 ) ; +#2420 = PRESENTATION_STYLE_ASSIGNMENT (( #72344 ) ) ; +#2421 = VERTEX_POINT ( 'NONE', #58107 ) ; +#2422 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#2423 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5000000000000000000, 0.000000000000000000 ) ) ; +#2424 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90448 ), #72585 ) ; +#2425 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77562, 'distance_accuracy_value', 'NONE'); +#2426 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#2428 = AXIS2_PLACEMENT_3D ( 'NONE', #62219, #46849, #15697 ) ; +#2427 = LINE ( 'NONE', #18203, #4727 ) ; +#2429 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2430 = SURFACE_STYLE_USAGE ( .BOTH. , #73884 ) ; +#2431 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2432 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11377 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6392, #63501, #21269 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2433 = ORIENTED_EDGE ( 'NONE', *, *, #1005, .T. ) ; +#2434 = LINE ( 'NONE', #88210, #5644 ) ; +#2435 = SURFACE_STYLE_USAGE ( .BOTH. , #23533 ) ; +#2436 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86674, 'distance_accuracy_value', 'NONE'); +#2437 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#2438 = VECTOR ( 'NONE', #4288, 1000.000000000000000 ) ; +#2439 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27900, 'distance_accuracy_value', 'NONE'); +#2440 = SURFACE_STYLE_USAGE ( .BOTH. , #72362 ) ; +#2441 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #97251, #89623, #46127, #67612, #68116, #14474, #98696, #5311, #36525, #28834, #76291, #29826, #75799, #22687, #37520, #83476, #14968 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.186618759736393935E-05, 2.323904346643759807E-05, 3.426921534152052812E-05, 4.507030652980710523E-05, 5.551276335150415187E-05, 6.567704521174683706E-05, 7.571101037642306267E-05, 8.572455163037589381E-05, 9.576215954890746074E-05, 0.0001057997674674393936, 0.0001161881706724257835, 0.0001267890661517618927, 0.0001482612251753109964, 0.0001703348223623887565 ), + .UNSPECIFIED. ) ; +#2442 = EDGE_CURVE ( 'NONE', #83860, #55809, #89217, .T. ) ; +#2443 = EDGE_LOOP ( 'NONE', ( #37210, #51089, #78032, #94358 ) ) ; +#2444 = ORIENTED_EDGE ( 'NONE', *, *, #75675, .F. ) ; +#2446 = AXIS2_PLACEMENT_3D ( 'NONE', #64274, #95375, #95889 ) ; +#2445 = VECTOR ( 'NONE', #4709, 1000.000000000000000 ) ; +#2447 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68906 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89554, #27791, #81421 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2448 = PLANE ( 'NONE', #30877 ) ; +#2449 = ORIENTED_EDGE ( 'NONE', *, *, #568, .T. ) ; +#2450 = LINE ( 'NONE', #48428, #90106 ) ; +#2451 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2452 = SURFACE_SIDE_STYLE ('',( #2954 ) ) ; +#2453 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46430 ), #15453 ) ; +#2454 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #26718 ) ; +#2455 = CARTESIAN_POINT ( 'NONE', ( 0.9663713008889384115, -1.365159793661692600, 0.8099999999997602451 ) ) ; +#2457 = VERTEX_POINT ( 'NONE', #33082 ) ; +#2456 = EDGE_LOOP ( 'NONE', ( #69076, #33627, #80575, #8711 ) ) ; +#2458 = ORIENTED_EDGE ( 'NONE', *, *, #96250, .T. ) ; +#2459 = ORIENTED_EDGE ( 'NONE', *, *, #40988, .T. ) ; +#2460 = PRESENTATION_STYLE_ASSIGNMENT (( #48440 ) ) ; +#2461 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999967137, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#2463 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#2462 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#2464 = ORIENTED_EDGE ( 'NONE', *, *, #42169, .T. ) ; +#2465 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_DFN1006.STEP', ( #1202, #63198 ), #17515 ) ; +#2466 = ADVANCED_FACE ( 'NONE', ( #81586 ), #9994, .T. ) ; +#2467 = FACE_OUTER_BOUND ( 'NONE', #54313, .T. ) ; +#2468 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#2469 = STYLED_ITEM ( 'NONE', ( #82451 ), #68230 ) ; +#2470 = ORIENTED_EDGE ( 'NONE', *, *, #26019, .T. ) ; +#2471 = ORIENTED_EDGE ( 'NONE', *, *, #70303, .F. ) ; +#2473 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2472 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -0.1499999999999999944 ) ) ; +#2474 = ADVANCED_FACE ( 'NONE', ( #98790 ), #51446, .T. ) ; +#2475 = ORIENTED_EDGE ( 'NONE', *, *, #18062, .T. ) ; +#2476 = ORIENTED_EDGE ( 'NONE', *, *, #61720, .F. ) ; +#2477 = LINE ( 'NONE', #56629, #36322 ) ; +#2478 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90505 ) ) ; +#2479 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46449 ), #88916 ) ; +#2481 = ORIENTED_EDGE ( 'NONE', *, *, #57287, .T. ) ; +#2480 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#2482 = SURFACE_STYLE_FILL_AREA ( #96879 ) ; +#2483 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2484 = ORIENTED_EDGE ( 'NONE', *, *, #13135, .T. ) ; +#2485 = FILL_AREA_STYLE ('',( #72409 ) ) ; +#2486 = VERTEX_POINT ( 'NONE', #28437 ) ; +#2487 = ORIENTED_EDGE ( 'NONE', *, *, #43181, .T. ) ; +#2488 = EDGE_CURVE ( 'NONE', #34980, #92575, #75893, .T. ) ; +#2490 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6600000000000000311, 0.7999999999999999334 ) ) ; +#2489 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2491 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38560 ), #2718 ) ; +#2492 = ADVANCED_FACE ( 'N', ( #21766 ), #90207, .T. ) ; +#2493 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2494 = STYLED_ITEM ( 'NONE', ( #37266 ), #82447 ) ; +#2495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80956 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45172, #77334, #53373 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2496 = VECTOR ( 'NONE', #56884, 1000.000000000000000 ) ; +#2497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58000 ) ) ; +#2498 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55902 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74577, #68871, #84720 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2499 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2500 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ipx3.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ipx3.STEP', '', ( #15187 ) ) ; +#2501 = FILL_AREA_STYLE ('',( #72420 ) ) ; +#2502 = SURFACE_SIDE_STYLE ('',( #17289 ) ) ; +#2503 = PRESENTATION_STYLE_ASSIGNMENT (( #93852 ) ) ; +#2504 = ORIENTED_EDGE ( 'NONE', *, *, #87286, .F. ) ; +#2505 = CIRCLE ( 'NONE', #38424, 0.04999999999999999584 ) ; +#2506 = FACE_OUTER_BOUND ( 'NONE', #40873, .T. ) ; +#2507 = ORIENTED_EDGE ( 'NONE', *, *, #87095, .T. ) ; +#2508 = FACE_OUTER_BOUND ( 'NONE', #72901, .T. ) ; +#2509 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#2510 = SURFACE_STYLE_FILL_AREA ( #8548 ) ; +#2511 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#2513 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38369 ) ) ; +#2512 = SURFACE_SIDE_STYLE ('',( #80139 ) ) ; +#2514 = PRESENTATION_STYLE_ASSIGNMENT (( #64292 ) ) ; +#2516 = VECTOR ( 'NONE', #40681, 1000.000000000000000 ) ; +#2515 = VECTOR ( 'NONE', #562, 1000.000000000000000 ) ; +#2517 = FILL_AREA_STYLE ('',( #94403 ) ) ; +#2518 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#2519 = FILL_AREA_STYLE ('',( #81149 ) ) ; +#2520 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#2521 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#2522 = PLANE ( 'NONE', #83853 ) ; +#2523 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6538 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63031, #93588, #8287 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2524 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2525 = EDGE_CURVE ( 'NONE', #50760, #70649, #30932, .T. ) ; +#2526 = SURFACE_STYLE_USAGE ( .BOTH. , #87272 ) ; +#2527 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2528 = FACE_OUTER_BOUND ( 'NONE', #78433, .T. ) ; +#2529 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2530 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2531 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55797 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45831, #23935, #53051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2532 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25794, 'distance_accuracy_value', 'NONE'); +#2533 = VERTEX_POINT ( 'NONE', #7871 ) ; +#2534 = PRESENTATION_STYLE_ASSIGNMENT (( #18833 ) ) ; +#2535 = ORIENTED_EDGE ( 'NONE', *, *, #97969, .F. ) ; +#2536 = LINE ( 'NONE', #32175, #20539 ) ; +#2537 = CYLINDRICAL_SURFACE ( 'NONE', #84456, 0.05000000000000012768 ) ; +#2538 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 8.286473000000000866, 0.8648700000000000276 ) ) ; +#2539 = SURFACE_SIDE_STYLE ('',( #41354 ) ) ; +#2540 = FILL_AREA_STYLE_COLOUR ( '', #99647 ) ; +#2541 = VECTOR ( 'NONE', #84232, 1000.000000000000000 ) ; +#2542 = CARTESIAN_POINT ( 'NONE', ( 1.745101982296789922, -0.9718760589866799471, 0.8100000000000006084 ) ) ; +#2543 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999969891, 0.000000000000000000 ) ) ; +#2544 = EDGE_CURVE ( 'NONE', #69886, #100076, #22271, .T. ) ; +#2545 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30207 ), #67743 ) ; +#2546 = ORIENTED_EDGE ( 'NONE', *, *, #54239, .T. ) ; +#2547 = VERTEX_POINT ( 'NONE', #94204 ) ; +#2548 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#2549 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.1000000000000000056, -0.02000000000001952993 ) ) ; +#2550 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#2552 = PRESENTATION_STYLE_ASSIGNMENT (( #41367 ) ) ; +#2551 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75936, #67754, #19814 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2553 = VECTOR ( 'NONE', #30766, 1000.000000000000114 ) ; +#2554 = CARTESIAN_POINT ( 'NONE', ( 10.82260475025008795, 8.130910249749913277, 0.8991599999999999593 ) ) ; +#2555 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100227 ), #40094 ) ; +#2556 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 2.311421000000000170, 0.8648700000000000276 ) ) ; +#2557 = ORIENTED_EDGE ( 'NONE', *, *, #44598, .T. ) ; +#2558 = EDGE_CURVE ( 'NONE', #14329, #91841, #93674, .T. ) ; +#2559 = SURFACE_STYLE_FILL_AREA ( #62341 ) ; +#2560 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2561 = EDGE_LOOP ( 'NONE', ( #1652, #9144, #45721, #17059 ) ) ; +#2562 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51496 ), #59675 ) ; +#2563 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51497 ), #77537 ) ; +#2564 = LINE ( 'NONE', #27568, #27566 ) ; +#2565 = VERTEX_POINT ( 'NONE', #24323 ) ; +#2566 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#2567 = VECTOR ( 'NONE', #94953, 1000.000000000000000 ) ; +#2568 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2569 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#2570 = SURFACE_STYLE_FILL_AREA ( #9632 ) ; +#2571 = CARTESIAN_POINT ( 'NONE', ( -1.024611994374110102, -1.021599245672099920, 0.8299999999999999600 ) ) ; +#2572 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2573 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2575 = VERTEX_POINT ( 'NONE', #14564 ) ; +#2574 = VERTEX_POINT ( 'NONE', #39104 ) ; +#2576 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#2577 = CYLINDRICAL_SURFACE ( 'NONE', #7115, 0.04999999999999991257 ) ; +#2578 = ORIENTED_EDGE ( 'NONE', *, *, #60285, .T. ) ; +#2579 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#2580 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28658 ), #13953 ) ; +#2581 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79249 ) ) ; +#2583 = SURFACE_SIDE_STYLE ('',( #20395 ) ) ; +#2582 = SURFACE_SIDE_STYLE ('',( #41894 ) ) ; +#2584 = EDGE_LOOP ( 'NONE', ( #43040, #4861, #11166, #89455 ) ) ; +#2585 = VERTEX_POINT ( 'NONE', #15589 ) ; +#2587 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92276 ), #15586 ) ; +#2586 = FACE_OUTER_BOUND ( 'NONE', #48002, .T. ) ; +#2588 = VECTOR ( 'NONE', #19742, 1000.000000000000000 ) ; +#2589 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#2590 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2592 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2591 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#2593 = CARTESIAN_POINT ( 'NONE', ( -0.03214163119229276888, 0.5753100270687899753, 0.8100000000000001643 ) ) ; +#2594 = EDGE_LOOP ( 'NONE', ( #79397, #2114, #19517, #18911 ) ) ; +#2595 = ORIENTED_EDGE ( 'NONE', *, *, #21052, .F. ) ; +#2596 = ADVANCED_FACE ( 'NONE', ( #23802 ), #100260, .F. ) ; +#2597 = VECTOR ( 'NONE', #9182, 1000.000000000000000 ) ; +#2598 = VERTEX_POINT ( 'NONE', #61608 ) ; +#2599 = EDGE_CURVE ( 'NONE', #10900, #63866, #38597, .T. ) ; +#2600 = PRESENTATION_STYLE_ASSIGNMENT (( #3096 ) ) ; +#2601 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2602 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43400 ) ) ; +#2603 = VECTOR ( 'NONE', #35150, 1000.000000000000000 ) ; +#2604 = ORIENTED_EDGE ( 'NONE', *, *, #67826, .T. ) ; +#2605 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2606 = PLANE ( 'NONE', #81736 ) ; +#2607 = LINE ( 'NONE', #72533, #31868 ) ; +#2608 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2609 = ORIENTED_EDGE ( 'NONE', *, *, #45637, .T. ) ; +#2610 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#2611 = CARTESIAN_POINT ( 'NONE', ( -1.020636429004242451, -1.410691121758086641, 0.8099999999996855271 ) ) ; +#2612 = VERTEX_POINT ( 'NONE', #39610 ) ; +#2613 = EDGE_CURVE ( 'NONE', #80224, #90793, #1309, .T. ) ; +#2614 = PLANE ( 'NONE', #85611 ) ; +#2615 = EDGE_CURVE ( 'NONE', #86226, #93560, #32465, .T. ) ; +#2616 = CARTESIAN_POINT ( 'NONE', ( 0.2614586316904913277, -1.017736618579592189, 0.8100000000000000533 ) ) ; +#2617 = LINE ( 'NONE', #25607, #43275 ) ; +#2618 = CARTESIAN_POINT ( 'NONE', ( 11.79841287512498837, 7.155102875124987882, 0.8991599999999999593 ) ) ; +#2619 = SURFACE_STYLE_FILL_AREA ( #17899 ) ; +#2621 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#2620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2622 = CARTESIAN_POINT ( 'NONE', ( 1.680683372326140068, -0.9625852181168450539, 0.8299999999999990719 ) ) ; +#2623 = VERTEX_POINT ( 'NONE', #7371 ) ; +#2624 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2625 = EDGE_LOOP ( 'NONE', ( #96706, #38743, #64983, #89408 ) ) ; +#2626 = FACE_OUTER_BOUND ( 'NONE', #15469, .T. ) ; +#2628 = ADVANCED_FACE ( 'NONE', ( #77387 ), #69720, .T. ) ; +#2627 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#2629 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2630 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20530 ), #97120 ) ; +#2631 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000000311, 0.1399999999999965994 ) ) ; +#2632 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.000000000000000000 ) ) ; +#2633 = CARTESIAN_POINT ( 'NONE', ( 1.799876578750339906, -1.066767002799750008, 0.8100000000000000533 ) ) ; +#2635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76007 ), #5845 ) ; +#2634 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, 0.000000000000000000 ) ) ; +#2636 = ADVANCED_FACE ( 'NONE', ( #57995 ), #10376, .T. ) ; +#2637 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35239 ) ) ; +#2638 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2639 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87391 ), #97210 ) ; +#2640 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#2641 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.5105124837953329830, -0.7500000000000000000 ) ) ; +#2642 = ORIENTED_EDGE ( 'NONE', *, *, #80253, .F. ) ; +#2643 = EDGE_CURVE ( 'NONE', #35737, #64015, #42142, .T. ) ; +#2645 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#2644 = VECTOR ( 'NONE', #82589, 1000.000000000000000 ) ; +#2646 = EDGE_CURVE ( 'NONE', #74498, #25602, #94708, .T. ) ; +#2647 = SURFACE_STYLE_USAGE ( .BOTH. , #89908 ) ; +#2648 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2649 = FILL_AREA_STYLE_COLOUR ( '', #4374 ) ; +#2650 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2651 = EDGE_CURVE ( 'NONE', #93940, #52114, #79435, .T. ) ; +#2652 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59827 ) ) ; +#2653 = SURFACE_SIDE_STYLE ('',( #32010 ) ) ; +#2654 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18019, 'distance_accuracy_value', 'NONE'); +#2655 = ORIENTED_EDGE ( 'NONE', *, *, #40970, .F. ) ; +#2656 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.09999999999999910349, 0.1829999999999749605 ) ) ; +#2657 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #75127 ) ) ; +#2658 = SURFACE_STYLE_USAGE ( .BOTH. , #96044 ) ; +#2660 = STYLED_ITEM ( 'NONE', ( #31627 ), #39518 ) ; +#2659 = SURFACE_STYLE_FILL_AREA ( #96046 ) ; +#2661 = LINE ( 'NONE', #82285, #13421 ) ; +#2662 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28727 ) ) ; +#2663 = CARTESIAN_POINT ( 'NONE', ( 7.700000000000000178, 15.40000000000000036, 0.8648700000000000276 ) ) ; +#2664 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2665 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#2666 = CARTESIAN_POINT ( 'NONE', ( -1.010125602507139897, -1.400043273498619900, 0.8300000000000001821 ) ) ; +#2667 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2668 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2669 = STYLED_ITEM ( 'NONE', ( #15483 ), #14130 ) ; +#2670 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2671 = ADVANCED_FACE ( 'NONE', ( #73780 ), #3328, .F. ) ; +#2672 = ORIENTED_EDGE ( 'NONE', *, *, #46717, .T. ) ; +#2673 = SURFACE_STYLE_USAGE ( .BOTH. , #95550 ) ; +#2674 = ORIENTED_EDGE ( 'NONE', *, *, #30791, .T. ) ; +#2675 = CIRCLE ( 'NONE', #93931, 0.009999999999999998473 ) ; +#2676 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31223, 'distance_accuracy_value', 'NONE'); +#2677 = PLANE ( 'NONE', #44659 ) ; +#2678 = CARTESIAN_POINT ( 'NONE', ( -0.2223607051232819876, -1.054251812769849916, 0.8100000000000000533 ) ) ; +#2679 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#2680 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#2681 = LINE ( 'NONE', #80292, #94926 ) ; +#2682 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2683 = LINE ( 'NONE', #96571, #3183 ) ; +#2684 = SURFACE_STYLE_FILL_AREA ( #57843 ) ; +#2685 = VERTEX_POINT ( 'NONE', #34499 ) ; +#2686 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2687 = ADVANCED_FACE ( 'NONE', ( #56486 ), #15425, .F. ) ; +#2688 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#2689 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#2690 = LINE ( 'NONE', #64966, #72165 ) ; +#2691 = ORIENTED_EDGE ( 'NONE', *, *, #82292, .T. ) ; +#2692 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.500000000000000222, 0.8100000000000000533 ) ) ; +#2693 = SURFACE_STYLE_FILL_AREA ( #32320 ) ; +#2694 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2695 = EDGE_LOOP ( 'NONE', ( #17387, #26379, #99326, #24125 ) ) ; +#2696 = EDGE_CURVE ( 'NONE', #70219, #66436, #60745, .T. ) ; +#2697 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18718 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52620, #21446, #38289 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2698 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2699 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27199 ) ) ; +#2700 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999959338, -0.1400000000000000133 ) ) ; +#2701 = EDGE_CURVE ( 'NONE', #2963, #14941, #78995, .T. ) ; +#2702 = ORIENTED_EDGE ( 'NONE', *, *, #85618, .F. ) ; +#2703 = ORIENTED_EDGE ( 'NONE', *, *, #95363, .F. ) ; +#2704 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2705 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49944 ) ) ; +#2706 = AXIS2_PLACEMENT_3D ( 'NONE', #55895, #8304, #40052 ) ; +#2707 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71198 ), #79374 ) ; +#2708 = VERTEX_POINT ( 'NONE', #100506 ) ; +#2709 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2710 = FILL_AREA_STYLE ('',( #25215 ) ) ; +#2711 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2712 = CARTESIAN_POINT ( 'NONE', ( 1.783305012356700026, -1.001398657004090254, 0.8300000000000004041 ) ) ; +#2713 = SURFACE_STYLE_USAGE ( .BOTH. , #80328 ) ; +#2714 = FACE_OUTER_BOUND ( 'NONE', #100871, .T. ) ; +#2715 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#2717 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2716 = CARTESIAN_POINT ( 'NONE', ( 0.2502762232558249922, -1.044215898305860035, 0.8100000000000000533 ) ) ; +#2718 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75734 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11521, #34614, #96842 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2719 = EDGE_LOOP ( 'NONE', ( #1, #96395, #68854, #31474 ) ) ; +#2721 = ORIENTED_EDGE ( 'NONE', *, *, #9315, .F. ) ; +#2720 = ORIENTED_EDGE ( 'NONE', *, *, #59377, .T. ) ; +#2722 = ORIENTED_EDGE ( 'NONE', *, *, #58811, .T. ) ; +#2723 = EDGE_CURVE ( 'NONE', #93833, #9822, #13802, .T. ) ; +#2724 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1458578643762690474 ) ) ; +#2725 = ORIENTED_EDGE ( 'NONE', *, *, #62975, .F. ) ; +#2727 = ORIENTED_EDGE ( 'NONE', *, *, #13324, .F. ) ; +#2726 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2728 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41987 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21853, #76471, #15672 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2729 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2730 = FACE_OUTER_BOUND ( 'NONE', #80564, .T. ) ; +#2731 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#2732 = LINE ( 'NONE', #64004, #35806 ) ; +#2733 = VERTEX_POINT ( 'NONE', #83327 ) ; +#2734 = LINE ( 'NONE', #10272, #1520 ) ; +#2735 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980549, 0.000000000000000000 ) ) ; +#2736 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2737 = ORIENTED_EDGE ( 'NONE', *, *, #61286, .T. ) ; +#2738 = FILL_AREA_STYLE ('',( #29585 ) ) ; +#2739 = AXIS2_PLACEMENT_3D ( 'NONE', #21837, #76453, #23356 ) ; +#2740 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853450583, 0.2349715759269650206, 0.8100000000000000533 ) ) ; +#2741 = EDGE_CURVE ( 'NONE', #71910, #59518, #30667, .T. ) ; +#2742 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71231 ), #85877 ) ; +#2743 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2744 = FACE_OUTER_BOUND ( 'NONE', #55992, .T. ) ; +#2745 = AXIS2_PLACEMENT_3D ( 'NONE', #59402, #82843, #11787 ) ; +#2746 = LINE ( 'NONE', #66028, #93998 ) ; +#2747 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2748 = VECTOR ( 'NONE', #94597, 1000.000000000000000 ) ; +#2749 = FILL_AREA_STYLE_COLOUR ( '', #97197 ) ; +#2750 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#2752 = SURFACE_STYLE_USAGE ( .BOTH. , #4737 ) ; +#2751 = CARTESIAN_POINT ( 'NONE', ( 0.3586905243120019904, -0.9624267057659720015, 0.8100000000000000533 ) ) ; +#2753 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#2754 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#2755 = CARTESIAN_POINT ( 'NONE', ( -1.132954166604120072, -0.8848558980161149723, 0.8299999999999999600 ) ) ; +#2756 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999902023, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#2757 = VECTOR ( 'NONE', #75956, 1000.000000000000000 ) ; +#2758 = ORIENTED_EDGE ( 'NONE', *, *, #95586, .T. ) ; +#2759 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#2760 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.000000000000000000 ) ) ; +#2761 = SURFACE_SIDE_STYLE ('',( #34926 ) ) ; +#2762 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#2763 = ORIENTED_EDGE ( 'NONE', *, *, #14076, .F. ) ; +#2764 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#2765 = SURFACE_STYLE_USAGE ( .BOTH. , #94126 ) ; +#2766 = EDGE_CURVE ( 'NONE', #16927, #58676, #44978, .T. ) ; +#2767 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2768 = CARTESIAN_POINT ( 'NONE', ( 1.581863761282799929, -1.087576819458450084, 0.8100000000000000533 ) ) ; +#2769 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#2770 = CYLINDRICAL_SURFACE ( 'NONE', #5526, 0.009999999999999998473 ) ; +#2771 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5385 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28735, #44545, #71963 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2772 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -6.286240788502049877E-13 ) ) ; +#2773 = SURFACE_STYLE_FILL_AREA ( #95149 ) ; +#2774 = ORIENTED_EDGE ( 'NONE', *, *, #80899, .F. ) ; +#2775 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, 3.149999999999990585, 0.000000000000000000 ) ) ; +#2776 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#2777 = FILL_AREA_STYLE_COLOUR ( '', #90519 ) ; +#2778 = SURFACE_STYLE_FILL_AREA ( #66069 ) ; +#2779 = LINE ( 'NONE', #58946, #100570 ) ; +#2780 = FILL_AREA_STYLE ('',( #89553 ) ) ; +#2781 = FILL_AREA_STYLE_COLOUR ( '', #97896 ) ; +#2782 = SURFACE_STYLE_FILL_AREA ( #9350 ) ; +#2783 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58178, #48990, #89286, #19322 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2784 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2785 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#2786 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5517 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93682, #78416, #70751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2787 = CARTESIAN_POINT ( 'NONE', ( 1.115802419441249915, -1.426518300252259897, 0.8299999999999999600 ) ) ; +#2788 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2789 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#2790 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2500000001077751222, -0.2299999998740531737 ) ) ; +#2791 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2792 = EDGE_LOOP ( 'NONE', ( #13399, #64512, #82680, #91216, #29282, #12162, #66262, #99990 ) ) ; +#2793 = FILL_AREA_STYLE_COLOUR ( '', #4029 ) ; +#2794 = ORIENTED_EDGE ( 'NONE', *, *, #85164, .F. ) ; +#2795 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#2796 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#2797 = CARTESIAN_POINT ( 'NONE', ( 0.2415003227679569930, -1.304818455916720188, 0.8299999999999999600 ) ) ; +#2798 = PRESENTATION_STYLE_ASSIGNMENT (( #40605 ) ) ; +#2799 = CARTESIAN_POINT ( 'NONE', ( 1.877768173756620085, -1.057175192472970204, 0.8299999999999999600 ) ) ; +#2800 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20709 ), #72909 ) ; +#2801 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999994671, -0.02000000000000000042 ) ) ; +#2802 = FACE_OUTER_BOUND ( 'NONE', #80842, .T. ) ; +#2803 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#2804 = CLOSED_SHELL ( 'NONE', ( #20945, #64027, #27154, #92033, #54344, #98623 ) ) ; +#2805 = ORIENTED_EDGE ( 'NONE', *, *, #75247, .F. ) ; +#2806 = SURFACE_SIDE_STYLE ('',( #34974 ) ) ; +#2807 = EDGE_CURVE ( 'NONE', #21305, #36447, #99038, .T. ) ; +#2808 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2809 = AXIS2_PLACEMENT_3D ( 'NONE', #40063, #94138, #11707 ) ; +#2810 = FILL_AREA_STYLE ('',( #2317 ) ) ; +#2811 = FILL_AREA_STYLE_COLOUR ( '', #7865 ) ; +#2812 = ORIENTED_EDGE ( 'NONE', *, *, #79386, .T. ) ; +#2813 = FACE_OUTER_BOUND ( 'NONE', #45709, .T. ) ; +#2814 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#2815 = FILL_AREA_STYLE_COLOUR ( '', #77158 ) ; +#2816 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2817 = PRESENTATION_STYLE_ASSIGNMENT (( #87573 ) ) ; +#2818 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2819 = ADVANCED_FACE ( 'NONE', ( #91963 ), #56735, .T. ) ; +#2820 = VERTEX_POINT ( 'NONE', #63390 ) ; +#2821 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#2822 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53463, 'distance_accuracy_value', 'NONE'); +#2823 = ADVANCED_FACE ( 'NONE', ( #69986 ), #546, .T. ) ; +#2824 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#2825 = EDGE_LOOP ( 'NONE', ( #36417, #67942, #95879, #26714 ) ) ; +#2826 = LINE ( 'NONE', #73777, #44706 ) ; +#2827 = SURFACE_STYLE_FILL_AREA ( #66606 ) ; +#2828 = SURFACE_STYLE_FILL_AREA ( #40636 ) ; +#2829 = STYLED_ITEM ( 'NONE', ( #34049 ), #74241 ) ; +#2830 = SURFACE_STYLE_USAGE ( .BOTH. , #82455 ) ; +#2831 = SURFACE_STYLE_FILL_AREA ( #9886 ) ; +#2832 = EDGE_CURVE ( 'NONE', #35264, #51520, #33294, .T. ) ; +#2833 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #35618, #9417 ) ; +#2834 = AXIS2_PLACEMENT_3D ( 'NONE', #3400, #42209, #49876 ) ; +#2835 = EDGE_CURVE ( 'NONE', #63412, #82698, #10514, .T. ) ; +#2836 = EDGE_LOOP ( 'NONE', ( #34397, #71249, #51028, #84827 ) ) ; +#2837 = EDGE_CURVE ( 'NONE', #99540, #99345, #64362, .T. ) ; +#2839 = ORIENTED_EDGE ( 'NONE', *, *, #15709, .T. ) ; +#2838 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2840 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58270 ), #28919 ) ; +#2841 = AXIS2_PLACEMENT_3D ( 'NONE', #77984, #68292, #70309 ) ; +#2842 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57899, 'distance_accuracy_value', 'NONE'); +#2843 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#2844 = FILL_AREA_STYLE ('',( #71264 ) ) ; +#2845 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.300000000000000044, -0.02000000000000000042 ) ) ; +#2846 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#2847 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#2848 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2849 = ORIENTED_EDGE ( 'NONE', *, *, #29455, .T. ) ; +#2850 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55048 ), #56737 ) ; +#2851 = SURFACE_STYLE_FILL_AREA ( #24336 ) ; +#2852 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2853 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42654, #21665, #66132, #91112 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#2854 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.000000000000000000 ) ) ; +#2855 = EDGE_CURVE ( 'NONE', #84919, #49566, #1061, .T. ) ; +#2856 = FACE_OUTER_BOUND ( 'NONE', #66143, .T. ) ; +#2857 = ORIENTED_EDGE ( 'NONE', *, *, #11296, .T. ) ; +#2858 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33845 ), #12609 ) ; +#2860 = FILL_AREA_STYLE ('',( #97730 ) ) ; +#2859 = FILL_AREA_STYLE ('',( #59026 ) ) ; +#2861 = EDGE_LOOP ( 'NONE', ( #38499, #28580, #57869, #54730 ) ) ; +#2862 = VERTEX_POINT ( 'NONE', #72031 ) ; +#2863 = CARTESIAN_POINT ( 'NONE', ( 1.028545535506111941, -1.163560561378816471, 0.8099999999998871436 ) ) ; +#2864 = ADVANCED_FACE ( 'NONE', ( #33228 ), #93939, .T. ) ; +#2866 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#2865 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#2867 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2868 = STYLED_ITEM ( 'NONE', ( #9842 ), #24366 ) ; +#2869 = SURFACE_SIDE_STYLE ('',( #42671 ) ) ; +#2870 = ORIENTED_EDGE ( 'NONE', *, *, #41024, .T. ) ; +#2871 = LINE ( 'NONE', #49850, #48362 ) ; +#2872 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31668 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11850, #98626, #82418 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2873 = PRESENTATION_STYLE_ASSIGNMENT (( #64643 ) ) ; +#2874 = ORIENTED_EDGE ( 'NONE', *, *, #91324, .F. ) ; +#2875 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#2876 = PLANE ( 'NONE', #99865 ) ; +#2877 = ORIENTED_EDGE ( 'NONE', *, *, #41468, .F. ) ; +#2878 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#2879 = CLOSED_SHELL ( 'NONE', ( #55165, #76519, #54502, #19660, #94289, #67365 ) ) ; +#2880 = FILL_AREA_STYLE_COLOUR ( '', #26571 ) ; +#2881 = CARTESIAN_POINT ( 'NONE', ( -1.367649144690350038, -1.097307480365639965, 0.8100000000000000533 ) ) ; +#2882 = LINE ( 'NONE', #96268, #77489 ) ; +#2883 = VECTOR ( 'NONE', #97457, 1000.000000000000000 ) ; +#2884 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#2885 = FACE_OUTER_BOUND ( 'NONE', #44474, .T. ) ; +#2886 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55310 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88396, #55265, #8672 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2887 = CARTESIAN_POINT ( 'NONE', ( -0.1139798271265630020, -1.164588072778879990, 0.8299999999999999600 ) ) ; +#2888 = CARTESIAN_POINT ( 'NONE', ( 1.306340380209440211, -0.9912247593444889482, 0.8299999999999999600 ) ) ; +#2889 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50223 ), #25781 ) ; +#2890 = ORIENTED_EDGE ( 'NONE', *, *, #78408, .F. ) ; +#2891 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#2892 = AXIS2_PLACEMENT_3D ( 'NONE', #58282, #12192, #14108 ) ; +#2893 = ADVANCED_FACE ( 'NONE', ( #81718 ), #27589, .T. ) ; +#2895 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#2894 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#2896 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12651, 'distance_accuracy_value', 'NONE'); +#2897 = SURFACE_SIDE_STYLE ('',( #42695 ) ) ; +#2898 = VECTOR ( 'NONE', #35709, 1000.000000000000000 ) ; +#2899 = FILL_AREA_STYLE ('',( #96780 ) ) ; +#2900 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#2901 = EDGE_CURVE ( 'NONE', #51090, #15430, #66675, .T. ) ; +#2902 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2903 = VERTEX_POINT ( 'NONE', #58252 ) ; +#2904 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2905 = SURFACE_STYLE_FILL_AREA ( #19717 ) ; +#2906 = FILL_AREA_STYLE ('',( #41712 ) ) ; +#2907 = SURFACE_SIDE_STYLE ('',( #78991 ) ) ; +#2908 = PRESENTATION_STYLE_ASSIGNMENT (( #10438 ) ) ; +#2909 = STYLED_ITEM ( 'NONE', ( #19510 ), #64824 ) ; +#2910 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#2911 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2912 = SURFACE_STYLE_FILL_AREA ( #97300 ) ; +#2913 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, -3.500000000000000444, 0.000000000000000000 ) ) ; +#2914 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14278 ), #37170 ) ; +#2915 = PLANE ( 'NONE', #71287 ) ; +#2916 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#2917 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2918 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#2919 = FILL_AREA_STYLE ('',( #72864 ) ) ; +#2920 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2921 = AXIS2_PLACEMENT_3D ( 'NONE', #22890, #39702, #53527 ) ; +#2922 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01500000000000000465, -0.1400000000000000133 ) ) ; +#2923 = SURFACE_STYLE_FILL_AREA ( #27411 ) ; +#2924 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -11.41999999999999993 ) ) ; +#2925 = ORIENTED_EDGE ( 'NONE', *, *, #59052, .T. ) ; +#2926 = PRESENTATION_STYLE_ASSIGNMENT (( #72871 ) ) ; +#2927 = EDGE_CURVE ( 'NONE', #17884, #26954, #11646, .T. ) ; +#2928 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#2929 = DIRECTION ( 'NONE', ( 0.7071075504167442238, 0.7071060119555140355, 0.000000000000000000 ) ) ; +#2930 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8648700000000000276 ) ) ; +#2931 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#2932 = STYLED_ITEM ( 'NONE', ( #13437 ), #17315 ) ; +#2933 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#2934 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#2936 = ORIENTED_EDGE ( 'NONE', *, *, #67079, .F. ) ; +#2935 = VECTOR ( 'NONE', #11719, 1000.000000000000000 ) ; +#2937 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8648700000000000276 ) ) ; +#2938 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#2939 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#2940 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4784314575050762630, 0.2458578643762689975 ) ) ; +#2941 = CLOSED_SHELL ( 'NONE', ( #88577, #6011, #12077, #100727, #31699, #76417 ) ) ; +#2942 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#2943 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25765 ), #51859 ) ; +#2944 = ORIENTED_EDGE ( 'NONE', *, *, #63332, .T. ) ; +#2945 = VERTEX_POINT ( 'NONE', #95976 ) ; +#2946 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12625 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49864, #89154, #97280 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2947 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#2948 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2949 = VERTEX_POINT ( 'NONE', #26080 ) ; +#2950 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63475 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45900, #61792, #6066 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2951 = FILL_AREA_STYLE ('',( #10490 ) ) ; +#2952 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#2953 = LINE ( 'NONE', #47897, #46466 ) ; +#2954 = SURFACE_STYLE_FILL_AREA ( #24448 ) ; +#2955 = STYLED_ITEM ( 'NONE', ( #76477 ), #15046 ) ; +#2956 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #21467 ) ; +#2957 = FILL_AREA_STYLE_COLOUR ( '', #3617 ) ; +#2958 = SURFACE_STYLE_FILL_AREA ( #57615 ) ; +#2959 = STYLED_ITEM ( 'NONE', ( #50109 ), #49952 ) ; +#2961 = VERTEX_POINT ( 'NONE', #3590 ) ; +#2960 = VERTEX_POINT ( 'NONE', #12160 ) ; +#2962 = ORIENTED_EDGE ( 'NONE', *, *, #39938, .T. ) ; +#2963 = VERTEX_POINT ( 'NONE', #89848 ) ; +#2964 = EDGE_CURVE ( 'NONE', #62366, #27038, #89351, .T. ) ; +#2965 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66818, 'distance_accuracy_value', 'NONE'); +#2967 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#2966 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#2968 = ORIENTED_EDGE ( 'NONE', *, *, #91272, .T. ) ; +#2969 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#2970 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #90609, .NOT_KNOWN. ) ; +#2971 = VERTEX_POINT ( 'NONE', #18376 ) ; +#2972 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47987 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47983, #16294, #85760 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#2974 = VERTEX_POINT ( 'NONE', #57750 ) ; +#2973 = STYLED_ITEM ( 'NONE', ( #36260 ), #74787 ) ; +#2975 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#2976 = ORIENTED_EDGE ( 'NONE', *, *, #16891, .F. ) ; +#2977 = ORIENTED_EDGE ( 'NONE', *, *, #56228, .F. ) ; +#2978 = FILL_AREA_STYLE_COLOUR ( '', #93332 ) ; +#2979 = ADVANCED_FACE ( 'NONE', ( #49565 ), #10640, .F. ) ; +#2980 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2981 = FILL_AREA_STYLE ('',( #42299 ) ) ; +#2982 = ORIENTED_EDGE ( 'NONE', *, *, #77010, .F. ) ; +#2983 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79592 ) ) ; +#2984 = SURFACE_STYLE_FILL_AREA ( #88746 ) ; +#2985 = LINE ( 'NONE', #46254, #81245 ) ; +#2986 = CARTESIAN_POINT ( 'NONE', ( -0.2824976818660340228, -1.013847726018640039, 0.8299999999999999600 ) ) ; +#2987 = ORIENTED_EDGE ( 'NONE', *, *, #74843, .F. ) ; +#2988 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#2989 = EDGE_LOOP ( 'NONE', ( #71538, #50853, #51748, #90597 ) ) ; +#2990 = VERTEX_POINT ( 'NONE', #60732 ) ; +#2991 = AXIS2_PLACEMENT_3D ( 'NONE', #100233, #20741, #52914 ) ; +#2992 = PLANE ( 'NONE', #26874 ) ; +#2993 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#2994 = LINE ( 'NONE', #85859, #3487 ) ; +#2995 = DIRECTION ( 'NONE', ( 0.7071067816865476141, -0.7071067806865475314, 0.000000000000000000 ) ) ; +#2996 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#2998 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50343 ), #14377 ) ; +#2997 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35349, 'distance_accuracy_value', 'NONE'); +#2999 = ORIENTED_EDGE ( 'NONE', *, *, #53438, .T. ) ; +#3000 = AXIS2_PLACEMENT_3D ( 'NONE', #37817, #38325, #30124 ) ; +#3001 = VECTOR ( 'NONE', #58077, 1000.000000000000000 ) ; +#3002 = CARTESIAN_POINT ( 'NONE', ( 0.03330623534528640017, -1.205608583660890076, 0.8299999999999999600 ) ) ; +#3003 = ORIENTED_EDGE ( 'NONE', *, *, #45250, .T. ) ; +#3004 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30291 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38164, #1366, #86113 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3005 = PRESENTATION_STYLE_ASSIGNMENT (( #33668 ) ) ; +#3006 = CARTESIAN_POINT ( 'NONE', ( 1.314694272500980032, -1.181578794826660284, 0.8100000000000000533 ) ) ; +#3007 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#3008 = SURFACE_STYLE_FILL_AREA ( #62288 ) ; +#3009 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#3010 = CLOSED_SHELL ( 'NONE', ( #95343, #83825, #59516, #97972, #49952, #34484 ) ) ; +#3011 = EDGE_CURVE ( 'NONE', #6630, #97223, #98926, .T. ) ; +#3012 = FACE_OUTER_BOUND ( 'NONE', #59958, .T. ) ; +#3013 = ORIENTED_EDGE ( 'NONE', *, *, #15892, .F. ) ; +#3014 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3015 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8199999999999999512 ) ) ; +#3016 = FACE_OUTER_BOUND ( 'NONE', #70011, .T. ) ; +#3017 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#3018 = SURFACE_STYLE_FILL_AREA ( #72442 ) ; +#3019 = SURFACE_STYLE_USAGE ( .BOTH. , #26515 ) ; +#3020 = CARTESIAN_POINT ( 'NONE', ( 1.352988682919539221, -1.482334922772619246, 0.8099999999996866373 ) ) ; +#3021 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64971 ) ) ; +#3022 = FILL_AREA_STYLE_COLOUR ( '', #76084 ) ; +#3023 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23634 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46783, #77950, #7912 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3025 = CARTESIAN_POINT ( 'NONE', ( -0.8280235389610389740, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#3026 = SURFACE_SIDE_STYLE ('',( #20343 ) ) ; +#3027 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#3028 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#3029 = ORIENTED_EDGE ( 'NONE', *, *, #66501, .F. ) ; +#3030 = CARTESIAN_POINT ( 'NONE', ( 1.674754468276729913, -0.9004049383407729534, 0.8100000000000000533 ) ) ; +#3031 = FACE_OUTER_BOUND ( 'NONE', #71413, .T. ) ; +#3032 = VERTEX_POINT ( 'NONE', #5546 ) ; +#3033 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3034 = LINE ( 'NONE', #65832, #48286 ) ; +#3035 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3036 = PRESENTATION_STYLE_ASSIGNMENT (( #67192 ) ) ; +#3037 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3038 = STYLED_ITEM ( 'NONE', ( #91239 ), #75184 ) ; +#3039 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999556, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#3040 = SURFACE_STYLE_USAGE ( .BOTH. , #49019 ) ; +#3041 = EDGE_CURVE ( 'NONE', #80825, #66256, #13678, .T. ) ; +#3042 = VECTOR ( 'NONE', #1039, 1000.000000000000000 ) ; +#3043 = VECTOR ( 'NONE', #12618, 1000.000000000000000 ) ; +#3044 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#3045 = ORIENTED_EDGE ( 'NONE', *, *, #51349, .T. ) ; +#3046 = ORIENTED_EDGE ( 'NONE', *, *, #78746, .F. ) ; +#3047 = SURFACE_STYLE_USAGE ( .BOTH. , #89326 ) ; +#3048 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76894, 'distance_accuracy_value', 'NONE'); +#3049 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -0.4333333333333353465, 0.000000000000000000 ) ) ; +#3050 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.6999999999999999556, -13.35000000000000142 ) ) ; +#3051 = VECTOR ( 'NONE', #7006, 1000.000000000000000 ) ; +#3052 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3053 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.000000000000000000 ) ) ; +#3054 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3055 = VECTOR ( 'NONE', #56695, 1000.000000000000000 ) ; +#3056 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3057 = FILL_AREA_STYLE_COLOUR ( '', #4163 ) ; +#3058 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#3059 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3060 = EDGE_CURVE ( 'NONE', #98939, #18215, #67844, .T. ) ; +#3061 = VECTOR ( 'NONE', #41121, 1000.000000000000000 ) ; +#3063 = EDGE_CURVE ( 'NONE', #75133, #17207, #21404, .T. ) ; +#3062 = VECTOR ( 'NONE', #54574, 1000.000000000000114 ) ; +#3064 = EDGE_LOOP ( 'NONE', ( #51704, #39956, #97263, #65453 ) ) ; +#3065 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#3066 = VECTOR ( 'NONE', #56665, 1000.000000000000000 ) ; +#3067 = ORIENTED_EDGE ( 'NONE', *, *, #65910, .T. ) ; +#3068 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#3069 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8648700000000000276 ) ) ; +#3070 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16698 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83617, #100303, #99803 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3071 = CARTESIAN_POINT ( 'NONE', ( -1.089702767725039934, -0.9656714926165439472, 0.8299999999999999600 ) ) ; +#3072 = SURFACE_STYLE_FILL_AREA ( #49049 ) ; +#3074 = VECTOR ( 'NONE', #7342, 1000.000000000000000 ) ; +#3073 = PRESENTATION_STYLE_ASSIGNMENT (( #69460 ) ) ; +#3076 = ORIENTED_EDGE ( 'NONE', *, *, #30211, .F. ) ; +#3075 = ORIENTED_EDGE ( 'NONE', *, *, #28106, .F. ) ; +#3077 = LINE ( 'NONE', #65349, #77309 ) ; +#3078 = EDGE_LOOP ( 'NONE', ( #73516, #45493, #5659, #32986 ) ) ; +#3079 = EDGE_CURVE ( 'NONE', #57093, #16467, #91354, .T. ) ; +#3080 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3082 = SURFACE_STYLE_USAGE ( .BOTH. , #88850 ) ; +#3081 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3083 = VERTEX_POINT ( 'NONE', #52566 ) ; +#3084 = ORIENTED_EDGE ( 'NONE', *, *, #59560, .F. ) ; +#3085 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#3086 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333322646, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#3087 = FILL_AREA_STYLE_COLOUR ( '', #52885 ) ; +#3088 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3089 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#3090 = FILL_AREA_STYLE ('',( #73039 ) ) ; +#3092 = VERTEX_POINT ( 'NONE', #38243 ) ; +#3091 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3093 = ORIENTED_EDGE ( 'NONE', *, *, #85109, .F. ) ; +#3094 = PLANE ( 'NONE', #64923 ) ; +#3095 = ORIENTED_EDGE ( 'NONE', *, *, #17921, .F. ) ; +#3096 = SURFACE_STYLE_USAGE ( .BOTH. , #79722 ) ; +#3097 = VECTOR ( 'NONE', #93532, 1000.000000000000000 ) ; +#3098 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#3099 = EDGE_CURVE ( 'NONE', #63488, #27435, #68358, .T. ) ; +#3100 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84893 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71174, #26242, #34416 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3103 = ORIENTED_EDGE ( 'NONE', *, *, #61196, .F. ) ; +#3102 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17796 ), #69983 ) ; +#3101 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.233333333333333393, 0.000000000000000000 ) ) ; +#3104 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3105 = ORIENTED_EDGE ( 'NONE', *, *, #80824, .F. ) ; +#3106 = ORIENTED_EDGE ( 'NONE', *, *, #67870, .T. ) ; +#3107 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#3108 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3109 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91144 ) ) ; +#3111 = EDGE_CURVE ( 'NONE', #78702, #95096, #99419, .T. ) ; +#3110 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3112 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#3113 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#3114 = VECTOR ( 'NONE', #39206, 1000.000000000000000 ) ; +#3116 = CYLINDRICAL_SURFACE ( 'NONE', #90633, 0.04999999999999991257 ) ; +#3115 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3117 = EDGE_CURVE ( 'NONE', #35265, #98440, #53568, .T. ) ; +#3118 = CARTESIAN_POINT ( 'NONE', ( 1.588352962588889916, -1.042364979248350032, 0.8299999999999990719 ) ) ; +#3119 = EDGE_LOOP ( 'NONE', ( #4140, #19162, #17622, #37459 ) ) ; +#3120 = CARTESIAN_POINT ( 'NONE', ( 1.673324881778589956, -1.507258815139120189, 0.8099999999999982769 ) ) ; +#3121 = SURFACE_STYLE_USAGE ( .BOTH. , #66410 ) ; +#3122 = ORIENTED_EDGE ( 'NONE', *, *, #21012, .T. ) ; +#3123 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3125 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#3124 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40666 ) ) ; +#3126 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#3127 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3128 = STYLED_ITEM ( 'NONE', ( #100724 ), #91887 ) ; +#3129 = LINE ( 'NONE', #34305, #663 ) ; +#3130 = CARTESIAN_POINT ( 'NONE', ( 0.3999999999999998557, 0.7578679656440356904, 0.1999999999999999833 ) ) ; +#3132 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#3131 = CARTESIAN_POINT ( 'NONE', ( -0.01268109447501128244, -1.406741836953922853, 0.8099999999996381206 ) ) ; +#3133 = EDGE_CURVE ( 'NONE', #934, #13261, #57818, .T. ) ; +#3134 = AXIS2_PLACEMENT_3D ( 'NONE', #54830, #92085, #36990 ) ; +#3135 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#3136 = STYLED_ITEM ( 'NONE', ( #5407 ), #6271 ) ; +#3137 = SURFACE_STYLE_USAGE ( .BOTH. , #73083 ) ; +#3138 = VECTOR ( 'NONE', #71701, 1000.000000000000000 ) ; +#3139 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3140 = FACE_OUTER_BOUND ( 'NONE', #63482, .T. ) ; +#3141 = VERTEX_POINT ( 'NONE', #92342 ) ; +#3142 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55357 ), #29230 ) ; +#3143 = SURFACE_STYLE_FILL_AREA ( #58813 ) ; +#3144 = FILL_AREA_STYLE ('',( #18953 ) ) ; +#3145 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#3146 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54150 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49161, #24177, #48660 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3147 = STYLED_ITEM ( 'NONE', ( #9684 ), #321 ) ; +#3148 = ORIENTED_EDGE ( 'NONE', *, *, #3011, .T. ) ; +#3149 = PLANE ( 'NONE', #59048 ) ; +#3150 = FACE_OUTER_BOUND ( 'NONE', #41008, .T. ) ; +#3151 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3152 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#3153 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#3154 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3155 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3157 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3158 = EDGE_CURVE ( 'NONE', #54622, #38179, #6022, .T. ) ; +#3159 = EDGE_CURVE ( 'NONE', #81506, #93205, #69328, .T. ) ; +#3160 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3161 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27978, 'distance_accuracy_value', 'NONE'); +#3162 = FACE_OUTER_BOUND ( 'NONE', #28718, .T. ) ; +#3163 = VERTEX_POINT ( 'NONE', #53065 ) ; +#3164 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#3165 = VERTEX_POINT ( 'NONE', #84201 ) ; +#3166 = FILL_AREA_STYLE_COLOUR ( '', #53537 ) ; +#3167 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26021, 'distance_accuracy_value', 'NONE'); +#3168 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38634, 'distance_accuracy_value', 'NONE'); +#3169 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#3170 = FILL_AREA_STYLE_COLOUR ( '', #65001 ) ; +#3171 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3172 = SURFACE_STYLE_USAGE ( .BOTH. , #32814 ) ; +#3173 = FACE_OUTER_BOUND ( 'NONE', #23432, .T. ) ; +#3174 = ORIENTED_EDGE ( 'NONE', *, *, #87805, .T. ) ; +#3175 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#3176 = EDGE_CURVE ( 'NONE', #92486, #21754, #14704, .T. ) ; +#3177 = FILL_AREA_STYLE_COLOUR ( '', #69360 ) ; +#3178 = FACE_OUTER_BOUND ( 'NONE', #21533, .T. ) ; +#3179 = ADVANCED_FACE ( 'NONE', ( #6998 ), #100391, .T. ) ; +#3180 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3181 = VERTEX_POINT ( 'NONE', #8001 ) ; +#3182 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3183 = VECTOR ( 'NONE', #34350, 1000.000000000000000 ) ; +#3184 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3185 = ORIENTED_EDGE ( 'NONE', *, *, #96981, .F. ) ; +#3186 = ADVANCED_FACE ( 'NONE', ( #63263 ), #55602, .T. ) ; +#3187 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3188 = AXIS2_PLACEMENT_3D ( 'NONE', #89613, #21166, #19668 ) ; +#3189 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37238 ) ) ; +#3190 = FILL_AREA_STYLE_COLOUR ( '', #100488 ) ; +#3191 = SURFACE_STYLE_FILL_AREA ( #3685 ) ; +#3192 = FILL_AREA_STYLE ('',( #26694 ) ) ; +#3193 = CARTESIAN_POINT ( 'NONE', ( -0.1381505133853424272, 2.561284075926966608, 0.8299999999999999600 ) ) ; +#3194 = ORIENTED_EDGE ( 'NONE', *, *, #73369, .F. ) ; +#3195 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3196 = VECTOR ( 'NONE', #99283, 1000.000000000000000 ) ; +#3198 = SURFACE_SIDE_STYLE ('',( #64483 ) ) ; +#3197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97676 ) ) ; +#3199 = VERTEX_POINT ( 'NONE', #32606 ) ; +#3200 = ADVANCED_FACE ( 'NONE', ( #70896 ), #87216, .T. ) ; +#3201 = SURFACE_SIDE_STYLE ('',( #35380 ) ) ; +#3202 = STYLED_ITEM ( 'NONE', ( #81793 ), #81380 ) ; +#3203 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71156, #38503, #47161, #63018 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#3204 = ORIENTED_EDGE ( 'NONE', *, *, #44663, .T. ) ; +#3205 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3206 = EDGE_CURVE ( 'NONE', #63293, #27223, #86712, .T. ) ; +#3207 = FILL_AREA_STYLE_COLOUR ( '', #52267 ) ; +#3208 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3209 = VECTOR ( 'NONE', #52636, 1000.000000000000000 ) ; +#3210 = FILL_AREA_STYLE_COLOUR ( '', #7754 ) ; +#3211 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#3213 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#3212 = CARTESIAN_POINT ( 'NONE', ( 0.2744150338662970090, -0.9994076953096140414, 0.8299999999999999600 ) ) ; +#3214 = ORIENTED_EDGE ( 'NONE', *, *, #98315, .T. ) ; +#3216 = ORIENTED_EDGE ( 'NONE', *, *, #83409, .F. ) ; +#3215 = VERTEX_POINT ( 'NONE', #17250 ) ; +#3217 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3218 = VERTEX_POINT ( 'NONE', #70365 ) ; +#3219 = PRESENTATION_STYLE_ASSIGNMENT (( #89493 ) ) ; +#3220 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87978 ), #70024 ) ; +#3221 = ADVANCED_FACE ( 'NONE', ( #31075 ), #58560, .T. ) ; +#3222 = ORIENTED_EDGE ( 'NONE', *, *, #33956, .F. ) ; +#3223 = ORIENTED_EDGE ( 'NONE', *, *, #69071, .T. ) ; +#3224 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.000000000000000000 ) ) ; +#3225 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#3226 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3227 = FACE_OUTER_BOUND ( 'NONE', #6284, .T. ) ; +#3228 = ORIENTED_EDGE ( 'NONE', *, *, #26421, .F. ) ; +#3229 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696238000000000135, 0.8991599999999999593 ) ) ; +#3230 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3231 = EDGE_LOOP ( 'NONE', ( #75377, #78476, #32597, #82050 ) ) ; +#3232 = SURFACE_STYLE_USAGE ( .BOTH. , #24740 ) ; +#3233 = LINE ( 'NONE', #34402, #81002 ) ; +#3234 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#3235 = SURFACE_STYLE_USAGE ( .BOTH. , #40166 ) ; +#3237 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#3236 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#3238 = PRESENTATION_STYLE_ASSIGNMENT (( #81383 ) ) ; +#3239 = PRESENTATION_STYLE_ASSIGNMENT (( #89522 ) ) ; +#3240 = EDGE_CURVE ( 'NONE', #90974, #49302, #18756, .T. ) ; +#3241 = FILL_AREA_STYLE_COLOUR ( '', #100700 ) ; +#3242 = STYLED_ITEM ( 'NONE', ( #86308 ), #44782 ) ; +#3243 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65194 ) ) ; +#3244 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3245 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3246 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3247 = SURFACE_SIDE_STYLE ('',( #50750 ) ) ; +#3248 = VECTOR ( 'NONE', #89452, 1000.000000000000000 ) ; +#3249 = SURFACE_STYLE_FILL_AREA ( #10824 ) ; +#3251 = EDGE_CURVE ( 'NONE', #85114, #53905, #49950, .T. ) ; +#3250 = CARTESIAN_POINT ( 'NONE', ( 0.9820030608313390363, -1.052663393014950044, 0.8299999999999999600 ) ) ; +#3252 = EDGE_LOOP ( 'NONE', ( #30875, #21943, #85689, #1950 ) ) ; +#3253 = CARTESIAN_POINT ( 'NONE', ( -1.154835151445229968, -1.515412412365080064, 0.8300000000000024025 ) ) ; +#3254 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2499999999940882844, -4.336808749769470492E-19 ) ) ; +#3255 = SURFACE_STYLE_USAGE ( .BOTH. , #2761 ) ; +#3256 = CARTESIAN_POINT ( 'NONE', ( 10.08014287512504126, 4.574162875125044714, 0.8648700000000000276 ) ) ; +#3257 = STYLED_ITEM ( 'NONE', ( #49972 ), #93281 ) ; +#3258 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3259 = ORIENTED_EDGE ( 'NONE', *, *, #63181, .T. ) ; +#3260 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3261 = ADVANCED_FACE ( 'NONE', ( #11026 ), #99299, .F. ) ; +#3263 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3262 = FILL_AREA_STYLE_COLOUR ( '', #18038 ) ; +#3264 = CARTESIAN_POINT ( 'NONE', ( 1.651684746960339956, -1.440618065759700084, 0.8099999999999976108 ) ) ; +#3265 = PRESENTATION_STYLE_ASSIGNMENT (( #49237 ) ) ; +#3266 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#3267 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31946 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93550, #47132, #76258 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3268 = AXIS2_PLACEMENT_3D ( 'NONE', #59853, #60342, #52169 ) ; +#3269 = VECTOR ( 'NONE', #76685, 1000.000000000000000 ) ; +#3270 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8199999999999999512 ) ) ; +#3271 = SURFACE_SIDE_STYLE ('',( #16538 ) ) ; +#3272 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45931, #92891, #86287 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3273 = FACE_OUTER_BOUND ( 'NONE', #51006, .T. ) ; +#3274 = ORIENTED_EDGE ( 'NONE', *, *, #72686, .T. ) ; +#3275 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3276 = SURFACE_STYLE_FILL_AREA ( #97170 ) ; +#3277 = LINE ( 'NONE', #35456, #79980 ) ; +#3278 = PLANE ( 'NONE', #872 ) ; +#3279 = CARTESIAN_POINT ( 'NONE', ( 1.020577689509359898, -0.9509517096142480197, 0.8299999999999994049 ) ) ; +#3280 = FACE_OUTER_BOUND ( 'NONE', #60634, .T. ) ; +#3281 = LINE ( 'NONE', #18576, #38703 ) ; +#3282 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3283 = PRESENTATION_STYLE_ASSIGNMENT (( #41096 ) ) ; +#3284 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3285 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18583 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34816, #52137, #19962 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3286 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3288 = EDGE_CURVE ( 'NONE', #48426, #30844, #67731, .T. ) ; +#3287 = FILL_AREA_STYLE_COLOUR ( '', #48420 ) ; +#3289 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3290 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70448, 'distance_accuracy_value', 'NONE'); +#3291 = PLANE ( 'NONE', #78432 ) ; +#3292 = SURFACE_STYLE_USAGE ( .BOTH. , #34460 ) ; +#3293 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3294 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84820 ) ) ; +#3295 = ORIENTED_EDGE ( 'NONE', *, *, #89965, .T. ) ; +#3296 = FACE_OUTER_BOUND ( 'NONE', #57848, .T. ) ; +#3297 = ORIENTED_EDGE ( 'NONE', *, *, #31780, .T. ) ; +#3299 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13642, 'distance_accuracy_value', 'NONE'); +#3298 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52215 ) ) ; +#3300 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69545, 'distance_accuracy_value', 'NONE'); +#3301 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3302 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3303 = FILL_AREA_STYLE ('',( #34469 ) ) ; +#3304 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3305 = ORIENTED_EDGE ( 'NONE', *, *, #79575, .T. ) ; +#3306 = EDGE_CURVE ( 'NONE', #20515, #36002, #53445, .T. ) ; +#3307 = PRESENTATION_STYLE_ASSIGNMENT (( #66582 ) ) ; +#3308 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42520, 'distance_accuracy_value', 'NONE'); +#3309 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3310 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37566 ) ) ; +#3311 = PLANE ( 'NONE', #91108 ) ; +#3312 = AXIS2_PLACEMENT_3D ( 'NONE', #56559, #41222, #94285 ) ; +#3313 = ORIENTED_EDGE ( 'NONE', *, *, #81359, .T. ) ; +#3314 = FILL_AREA_STYLE ('',( #27308 ) ) ; +#3315 = VECTOR ( 'NONE', #85650, 1000.000000000000000 ) ; +#3316 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53000, #83635, #14630, #67775 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#3317 = FILL_AREA_STYLE ('',( #2815 ) ) ; +#3318 = SURFACE_STYLE_FILL_AREA ( #72249 ) ; +#3319 = SURFACE_STYLE_FILL_AREA ( #89094 ) ; +#3320 = ORIENTED_EDGE ( 'NONE', *, *, #92911, .T. ) ; +#3321 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -2.300000000000000266, -0.02000000000000000042 ) ) ; +#3322 = STYLED_ITEM ( 'NONE', ( #37842 ), #44940 ) ; +#3323 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3324 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96, 'distance_accuracy_value', 'NONE'); +#3325 = FILL_AREA_STYLE_COLOUR ( '', #6649 ) ; +#3326 = CARTESIAN_POINT ( 'NONE', ( 1.877211804471179857, -1.084027901463999966, 0.8099999999999998312 ) ) ; +#3327 = EDGE_LOOP ( 'NONE', ( #44405, #9914, #8568, #22927, #45981, #93190 ) ) ; +#3328 = CYLINDRICAL_SURFACE ( 'NONE', #51038, 0.04999999999999969746 ) ; +#3329 = STYLED_ITEM ( 'NONE', ( #12512 ), #33403 ) ; +#3330 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#3331 = LINE ( 'NONE', #8880, #32518 ) ; +#3332 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3333 = PRODUCT ( 'ESP32-S3_20210301.xtd', 'ESP32-S3_20210301.xtd', '', ( #91825 ) ) ; +#3334 = VECTOR ( 'NONE', #94239, 1000.000000000000000 ) ; +#3335 = VECTOR ( 'NONE', #81151, 1000.000000000000000 ) ; +#3336 = ADVANCED_FACE ( 'NONE', ( #83590 ), #44741, .T. ) ; +#3337 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9807 ) ) ; +#3338 = ORIENTED_EDGE ( 'NONE', *, *, #15731, .T. ) ; +#3341 = VERTEX_POINT ( 'NONE', #6406 ) ; +#3340 = SURFACE_SIDE_STYLE ('',( #33491 ) ) ; +#3339 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3342 = AXIS2_PLACEMENT_3D ( 'NONE', #89391, #13723, #90384 ) ; +#3343 = LINE ( 'NONE', #9895, #97947 ) ; +#3345 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3344 = FILL_AREA_STYLE ('',( #35513 ) ) ; +#3346 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#3347 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47356 ) ) ; +#3348 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626904202, 0.1400000000000000133 ) ) ; +#3349 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2499999999999997780, 0.000000000000000000 ) ) ; +#3350 = ORIENTED_EDGE ( 'NONE', *, *, #16506, .F. ) ; +#3351 = VECTOR ( 'NONE', #301, 1000.000000000000000 ) ; +#3352 = CARTESIAN_POINT ( 'NONE', ( 1.329279248099940025, -1.493640573211080014, 0.8100000000000000533 ) ) ; +#3353 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3354 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#3355 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54561 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1524, #89301, #80153 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3356 = VERTEX_POINT ( 'NONE', #68720 ) ; +#3357 = VECTOR ( 'NONE', #29874, 1000.000000000000000 ) ; +#3359 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#3358 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3360 = ORIENTED_EDGE ( 'NONE', *, *, #50708, .T. ) ; +#3361 = ORIENTED_EDGE ( 'NONE', *, *, #19042, .F. ) ; +#3362 = CARTESIAN_POINT ( 'NONE', ( 0.9995854628762150806, -1.131943244623368372, 0.8099999999999069056 ) ) ; +#3364 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3363 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3365 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20594 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60547, #54893, #92139 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3366 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3367 = EDGE_CURVE ( 'NONE', #82073, #39240, #36134, .T. ) ; +#3368 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47391 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30743, #55291, #86403 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3369 = ORIENTED_EDGE ( 'NONE', *, *, #54456, .T. ) ; +#3370 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47375 ), #86520 ) ; +#3371 = PLANE ( 'NONE', #4365 ) ; +#3372 = SURFACE_STYLE_USAGE ( .BOTH. , #39141 ) ; +#3373 = ORIENTED_EDGE ( 'NONE', *, *, #58490, .F. ) ; +#3374 = LINE ( 'NONE', #81513, #51562 ) ; +#3375 = EDGE_LOOP ( 'NONE', ( #32956, #90297, #98665, #7763 ) ) ; +#3376 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3377 = CARTESIAN_POINT ( 'NONE', ( -1.024943210826370299, -1.268071887441960088, 0.8100000000000000533 ) ) ; +#3378 = EDGE_CURVE ( 'NONE', #55353, #52994, #32524, .T. ) ; +#3379 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#3380 = SURFACE_STYLE_FILL_AREA ( #41687 ) ; +#3381 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88944 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63074, #94669, #25294 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3382 = SURFACE_STYLE_USAGE ( .BOTH. , #40685 ) ; +#3383 = ADVANCED_FACE ( 'NONE', ( #59646 ), #23306, .F. ) ; +#3384 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3386 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.149999999999970157, 0.000000000000000000 ) ) ; +#3385 = AXIS2_PLACEMENT_3D ( 'NONE', #44693, #91183, #13497 ) ; +#3387 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3388 = CARTESIAN_POINT ( 'NONE', ( 1.314833503436970030, -1.000241703689469963, 0.8299999999999999600 ) ) ; +#3389 = ORIENTED_EDGE ( 'NONE', *, *, #50739, .T. ) ; +#3390 = SURFACE_SIDE_STYLE ('',( #96772 ) ) ; +#3391 = LINE ( 'NONE', #10951, #82295 ) ; +#3392 = ADVANCED_FACE ( 'NONE', ( #39625 ), #31462, .T. ) ; +#3394 = PLANE ( 'NONE', #51011 ) ; +#3393 = LINE ( 'NONE', #63679, #73488 ) ; +#3395 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3396 = CIRCLE ( 'NONE', #22996, 0.1000000000000000056 ) ; +#3397 = PRESENTATION_STYLE_ASSIGNMENT (( #81018 ) ) ; +#3398 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000000410, 8.413752999999999815, 0.8648700000000000276 ) ) ; +#3399 = SURFACE_STYLE_USAGE ( .BOTH. , #97766 ) ; +#3400 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#3401 = LINE ( 'NONE', #73844, #58215 ) ; +#3402 = EDGE_LOOP ( 'NONE', ( #3839, #94215, #71389, #31759 ) ) ; +#3403 = PRESENTATION_STYLE_ASSIGNMENT (( #50884 ) ) ; +#3404 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3405 = PRESENTATION_STYLE_ASSIGNMENT (( #98248 ) ) ; +#3406 = LINE ( 'NONE', #43685, #81139 ) ; +#3407 = CIRCLE ( 'NONE', #50651, 0.009999999999999998473 ) ; +#3408 = AXIS2_PLACEMENT_3D ( 'NONE', #28789, #12394, #21638 ) ; +#3409 = CARTESIAN_POINT ( 'NONE', ( 0.3213506759258810130, -1.250167574961789985, 0.8300000000000015143 ) ) ; +#3410 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54307, 'distance_accuracy_value', 'NONE'); +#3411 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3412 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3413 = FILL_AREA_STYLE ('',( #97779 ) ) ; +#3415 = EDGE_CURVE ( 'NONE', #29189, #12927, #70760, .T. ) ; +#3414 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#3416 = EDGE_CURVE ( 'NONE', #63379, #17500, #40143, .T. ) ; +#3417 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47417 ) ) ; +#3419 = FILL_AREA_STYLE ('',( #27397 ) ) ; +#3418 = VECTOR ( 'NONE', #28840, 1000.000000000000000 ) ; +#3420 = AXIS2_PLACEMENT_3D ( 'NONE', #20333, #43822, #27527 ) ; +#3421 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3422 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3423 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3424 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3425 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3426 = EDGE_CURVE ( 'NONE', #18616, #65234, #94726, .T. ) ; +#3427 = EDGE_CURVE ( 'NONE', #13692, #65417, #61214, .T. ) ; +#3428 = STYLED_ITEM ( 'NONE', ( #48035 ), #85791 ) ; +#3429 = LINE ( 'NONE', #26911, #24555 ) ; +#3430 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#3431 = VECTOR ( 'NONE', #45145, 1000.000000000000000 ) ; +#3432 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852913999999999728, 0.8648700000000000276 ) ) ; +#3433 = DIRECTION ( 'NONE', ( -0.3444045651374270656, 0.000000000000000000, -0.9388213331153589802 ) ) ; +#3434 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3435 = ORIENTED_EDGE ( 'NONE', *, *, #23697, .F. ) ; +#3436 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3437 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#3438 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8440, 'distance_accuracy_value', 'NONE'); +#3439 = EDGE_CURVE ( 'NONE', #74168, #70019, #77408, .T. ) ; +#3440 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31889, 'distance_accuracy_value', 'NONE'); +#3441 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12364 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #118, #92036, #61442 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3442 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3443 = EDGE_CURVE ( 'NONE', #95765, #66042, #93193, .T. ) ; +#3444 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.500000000000000000, 8.977651093538432215E-153 ) ) ; +#3445 = DIRECTION ( 'NONE', ( -0.7071067811865489050, 0.7071067811865462405, 0.000000000000000000 ) ) ; +#3446 = VECTOR ( 'NONE', #60920, 1000.000000000000000 ) ; +#3447 = ORIENTED_EDGE ( 'NONE', *, *, #40864, .F. ) ; +#3448 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45801 ) ) ; +#3449 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#3450 = CIRCLE ( 'NONE', #1835, 0.009999999999999998473 ) ; +#3451 = SURFACE_STYLE_USAGE ( .BOTH. , #73891 ) ; +#3452 = SURFACE_STYLE_FILL_AREA ( #42250 ) ; +#3453 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #211, 'distance_accuracy_value', 'NONE'); +#3454 = FILL_AREA_STYLE ('',( #63736 ) ) ; +#3455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97267, 'distance_accuracy_value', 'NONE'); +#3456 = SURFACE_SIDE_STYLE ('',( #65215 ) ) ; +#3457 = ORIENTED_EDGE ( 'NONE', *, *, #95294, .T. ) ; +#3458 = ORIENTED_EDGE ( 'NONE', *, *, #62876, .T. ) ; +#3459 = LINE ( 'NONE', #34609, #7983 ) ; +#3460 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#3461 = ORIENTED_EDGE ( 'NONE', *, *, #8177, .F. ) ; +#3462 = CARTESIAN_POINT ( 'NONE', ( 1.779394466811810016, -1.241062917987890257, 0.8299999999999999600 ) ) ; +#3463 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3464 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#3465 = SURFACE_STYLE_USAGE ( .BOTH. , #22150 ) ; +#3466 = CARTESIAN_POINT ( 'NONE', ( 0.9605208204589734677, -1.335111600150428401, 0.8099999999997792299 ) ) ; +#3468 = EDGE_LOOP ( 'NONE', ( #54319, #71672, #20773, #24048 ) ) ; +#3467 = ORIENTED_EDGE ( 'NONE', *, *, #67620, .T. ) ; +#3469 = ADVANCED_FACE ( 'NONE', ( #88116 ), #48819, .T. ) ; +#3470 = VERTEX_POINT ( 'NONE', #40646 ) ; +#3471 = ORIENTED_EDGE ( 'NONE', *, *, #100516, .T. ) ; +#3472 = FACE_OUTER_BOUND ( 'NONE', #21158, .T. ) ; +#3473 = SURFACE_STYLE_FILL_AREA ( #11534 ) ; +#3475 = FILL_AREA_STYLE_COLOUR ( '', #85525 ) ; +#3474 = DIRECTION ( 'NONE', ( -1.626303258728260102E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3476 = ORIENTED_EDGE ( 'NONE', *, *, #56011, .T. ) ; +#3477 = ADVANCED_FACE ( 'NONE', ( #26340 ), #57490, .F. ) ; +#3478 = STYLED_ITEM ( 'NONE', ( #34862 ), #33896 ) ; +#3479 = ORIENTED_EDGE ( 'NONE', *, *, #63134, .T. ) ; +#3480 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3481 = ORIENTED_EDGE ( 'NONE', *, *, #93953, .T. ) ; +#3483 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3482 = FILL_AREA_STYLE_COLOUR ( '', #64992 ) ; +#3484 = ORIENTED_EDGE ( 'NONE', *, *, #48079, .F. ) ; +#3485 = ORIENTED_EDGE ( 'NONE', *, *, #2117, .T. ) ; +#3486 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3487 = VECTOR ( 'NONE', #18277, 1000.000000000000000 ) ; +#3488 = CIRCLE ( 'NONE', #1810, 0.1000000000000000472 ) ; +#3489 = PLANE ( 'NONE', #18902 ) ; +#3490 = CARTESIAN_POINT ( 'NONE', ( 1.797750835596120256, -1.188470249711290228, 0.8300000000000004041 ) ) ; +#3491 = ADVANCED_FACE ( 'NONE', ( #34513 ), #22789, .F. ) ; +#3492 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#3493 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65412 ) ) ; +#3495 = ORIENTED_EDGE ( 'NONE', *, *, #24188, .T. ) ; +#3494 = FILL_AREA_STYLE_COLOUR ( '', #8619 ) ; +#3496 = STYLED_ITEM ( 'NONE', ( #59562 ), #8333 ) ; +#3497 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3498 = ORIENTED_EDGE ( 'NONE', *, *, #39674, .F. ) ; +#3499 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3500 = FACE_OUTER_BOUND ( 'NONE', #51270, .T. ) ; +#3501 = ORIENTED_EDGE ( 'NONE', *, *, #20189, .T. ) ; +#3502 = CARTESIAN_POINT ( 'NONE', ( 5.978923499499825489, 3.287228500500175787, 0.8991599999999999593 ) ) ; +#3503 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3504 = ORIENTED_EDGE ( 'NONE', *, *, #48285, .F. ) ; +#3505 = VERTEX_POINT ( 'NONE', #74296 ) ; +#3506 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#3507 = ADVANCED_FACE ( 'NONE', ( #37002 ), #97716, .F. ) ; +#3508 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94705 ) ) ; +#3509 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#3510 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3511 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3512 = VECTOR ( 'NONE', #98489, 1000.000000000000000 ) ; +#3513 = ORIENTED_EDGE ( 'NONE', *, *, #74276, .F. ) ; +#3514 = CARTESIAN_POINT ( 'NONE', ( 0.04300883857482180189, -1.212495751768609908, 0.8100000000000000533 ) ) ; +#3515 = ORIENTED_EDGE ( 'NONE', *, *, #62300, .F. ) ; +#3516 = EDGE_CURVE ( 'NONE', #63874, #95326, #44828, .T. ) ; +#3517 = CIRCLE ( 'NONE', #21422, 0.5799999999999999600 ) ; +#3518 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.000000000000000000 ) ) ; +#3519 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3520 = FILL_AREA_STYLE_COLOUR ( '', #83909 ) ; +#3521 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#3522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3523 = LINE ( 'NONE', #94890, #97619 ) ; +#3524 = FILL_AREA_STYLE_COLOUR ( '', #79442 ) ; +#3525 = EDGE_CURVE ( 'NONE', #19945, #38574, #54847, .T. ) ; +#3526 = SURFACE_SIDE_STYLE ('',( #9076 ) ) ; +#3527 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8648700000000000276 ) ) ; +#3528 = ORIENTED_EDGE ( 'NONE', *, *, #70575, .F. ) ; +#3529 = SURFACE_STYLE_USAGE ( .BOTH. , #27521 ) ; +#3530 = CARTESIAN_POINT ( 'NONE', ( 0.2295068781666219915, -0.9459922548521020325, 0.8299999999999999600 ) ) ; +#3531 = CARTESIAN_POINT ( 'NONE', ( 4.847552875125042959, 4.418599124874956097, 0.8648700000000000276 ) ) ; +#3532 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3533 = LINE ( 'NONE', #88290, #40811 ) ; +#3534 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#3535 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3536 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15547 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59130, #13044, #90222 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3537 = EDGE_CURVE ( 'NONE', #92376, #92966, #40012, .T. ) ; +#3538 = ADVANCED_FACE ( 'NONE', ( #46641 ), #71152, .T. ) ; +#3539 = PRESENTATION_STYLE_ASSIGNMENT (( #90286 ) ) ; +#3540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3542 = STYLED_ITEM ( 'NONE', ( #78781 ), #45682 ) ; +#3541 = SURFACE_STYLE_USAGE ( .BOTH. , #87275 ) ; +#3543 = FACE_OUTER_BOUND ( 'NONE', #52354, .T. ) ; +#3544 = EDGE_CURVE ( 'NONE', #36018, #87714, #87293, .T. ) ; +#3545 = ADVANCED_FACE ( 'NONE', ( #31836 ), #24214, .T. ) ; +#3546 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37352, 'distance_accuracy_value', 'NONE'); +#3547 = ORIENTED_EDGE ( 'NONE', *, *, #28218, .F. ) ; +#3548 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#3549 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3550 = VERTEX_POINT ( 'NONE', #69080 ) ; +#3551 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3552 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3553 = ADVANCED_FACE ( 'NONE', ( #30299 ), #92583, .T. ) ; +#3554 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73897 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78469, #12725, #90911 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3555 = STYLED_ITEM ( 'NONE', ( #73020 ), #34084 ) ; +#3556 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3557 = CARTESIAN_POINT ( 'NONE', ( 1.735855133396799976, -0.9683984092875529415, 0.8100000000000006084 ) ) ; +#3558 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100968 ) ; +#3559 = VECTOR ( 'NONE', #59042, 1000.000000000000000 ) ; +#3560 = ADVANCED_FACE ( 'NONE', ( #3716 ), #96116, .T. ) ; +#3561 = AXIS2_PLACEMENT_3D ( 'NONE', #24150, #84880, #37934 ) ; +#3562 = EDGE_LOOP ( 'NONE', ( #70067, #53684, #35384, #34624 ) ) ; +#3563 = ORIENTED_EDGE ( 'NONE', *, *, #20595, .T. ) ; +#3564 = FILL_AREA_STYLE ('',( #96948 ) ) ; +#3565 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#3566 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52463 ) ) ; +#3567 = CARTESIAN_POINT ( 'NONE', ( -0.4939079156693390038, -1.173538053626689948, 0.8100000000000000533 ) ) ; +#3568 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25098, 'distance_accuracy_value', 'NONE'); +#3569 = FILL_AREA_STYLE_COLOUR ( '', #7135 ) ; +#3570 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3571 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#3572 = ORIENTED_EDGE ( 'NONE', *, *, #55652, .F. ) ; +#3573 = LINE ( 'NONE', #34735, #73194 ) ; +#3574 = EDGE_LOOP ( 'NONE', ( #41021, #35386, #553, #94720, #97670, #32821 ) ) ; +#3575 = FILL_AREA_STYLE ('',( #83196 ) ) ; +#3576 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.1000000000000020040, 0.1829999999999709359 ) ) ; +#3577 = SURFACE_STYLE_USAGE ( .BOTH. , #36237 ) ; +#3578 = CARTESIAN_POINT ( 'NONE', ( -1.115369118623960043, -0.9585098101514269997, 0.8299999999999999600 ) ) ; +#3579 = VECTOR ( 'NONE', #40095, 1000.000000000000000 ) ; +#3580 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3581 = FACE_OUTER_BOUND ( 'NONE', #70373, .T. ) ; +#3582 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60589 ) ) ; +#3584 = ORIENTED_EDGE ( 'NONE', *, *, #23039, .F. ) ; +#3583 = VERTEX_POINT ( 'NONE', #3225 ) ; +#3585 = VECTOR ( 'NONE', #21062, 1000.000000000000000 ) ; +#3586 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3587 = ORIENTED_EDGE ( 'NONE', *, *, #94144, .T. ) ; +#3588 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, 0.1399999999999999856 ) ) ; +#3590 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#3589 = FILL_AREA_STYLE_COLOUR ( '', #71746 ) ; +#3591 = ORIENTED_EDGE ( 'NONE', *, *, #5879, .F. ) ; +#3592 = VECTOR ( 'NONE', #82433, 1000.000000000000000 ) ; +#3593 = EDGE_CURVE ( 'NONE', #19782, #31439, #18528, .T. ) ; +#3594 = VERTEX_POINT ( 'NONE', #79324 ) ; +#3595 = DIRECTION ( 'NONE', ( -1.401985567973789257E-16, 1.000000000000000000, -2.620751377075717173E-32 ) ) ; +#3596 = FILL_AREA_STYLE ('',( #87848 ) ) ; +#3597 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3598 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3600 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.449999999999999956, -0.2000000000000000111 ) ) ; +#3599 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3601 = ORIENTED_EDGE ( 'NONE', *, *, #33134, .F. ) ; +#3602 = VERTEX_POINT ( 'NONE', #65491 ) ; +#3603 = ORIENTED_EDGE ( 'NONE', *, *, #11716, .F. ) ; +#3604 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3606 = ORIENTED_EDGE ( 'NONE', *, *, #58451, .F. ) ; +#3605 = CARTESIAN_POINT ( 'NONE', ( -0.1711130133853430157, 2.469409075926966679, 0.8100000000000000533 ) ) ; +#3607 = CARTESIAN_POINT ( 'NONE', ( -1.970710678118652970, 1.529289321881341479, -0.02000000000000000042 ) ) ; +#3608 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3609 = ORIENTED_EDGE ( 'NONE', *, *, #32478, .F. ) ; +#3610 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#3611 = PRESENTATION_STYLE_ASSIGNMENT (( #26107 ) ) ; +#3612 = EDGE_LOOP ( 'NONE', ( #42061, #93348, #63741, #39239 ) ) ; +#3613 = ADVANCED_FACE ( 'NONE', ( #9284 ), #40533, .T. ) ; +#3614 = VERTEX_POINT ( 'NONE', #35894 ) ; +#3615 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220779480, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#3616 = VECTOR ( 'NONE', #21205, 1000.000000000000000 ) ; +#3617 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3618 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#3619 = CARTESIAN_POINT ( 'NONE', ( -1.324712406799700037, -1.164020980542209927, 0.8300000000000000711 ) ) ; +#3620 = VECTOR ( 'NONE', #40550, 1000.000000000000000 ) ; +#3621 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#3622 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3623 = LINE ( 'NONE', #34791, #98084 ) ; +#3624 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#3625 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3627 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3626 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3628 = CARTESIAN_POINT ( 'NONE', ( 1.617430281440370043, -0.9137302873894740385, 0.8299999999999997380 ) ) ; +#3629 = ORIENTED_EDGE ( 'NONE', *, *, #21546, .F. ) ; +#3630 = FILL_AREA_STYLE_COLOUR ( '', #63712 ) ; +#3631 = CARTESIAN_POINT ( 'NONE', ( -1.050422986827179939, -0.9018902076549559776, 0.8300000000000000711 ) ) ; +#3632 = VERTEX_POINT ( 'NONE', #90996 ) ; +#3633 = VECTOR ( 'NONE', #83343, 1000.000000000000000 ) ; +#3634 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3635 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3636 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#3637 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#3638 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28069 ) ) ; +#3639 = SURFACE_SIDE_STYLE ('',( #43938 ) ) ; +#3640 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#3641 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.009999999999999998473, -1.129999999999999893 ) ) ; +#3642 = EDGE_LOOP ( 'NONE', ( #21380, #72998, #86277, #73904 ) ) ; +#3643 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8100000000000086020 ) ) ; +#3644 = FILL_AREA_STYLE_COLOUR ( '', #21419 ) ; +#3645 = VECTOR ( 'NONE', #28587, 999.9999999999998863 ) ; +#3646 = LINE ( 'NONE', #57817, #19092 ) ; +#3647 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3648 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76418, 'distance_accuracy_value', 'NONE'); +#3649 = ORIENTED_EDGE ( 'NONE', *, *, #100555, .F. ) ; +#3650 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#3651 = SURFACE_SIDE_STYLE ('',( #66438 ) ) ; +#3652 = CARTESIAN_POINT ( 'NONE', ( -1.015038904699709921, -1.047446665233070062, 0.8299999999999999600 ) ) ; +#3653 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#3654 = LINE ( 'NONE', #65955, #45300 ) ; +#3655 = STYLED_ITEM ( 'NONE', ( #93011 ), #52035 ) ; +#3656 = LINE ( 'NONE', #5620, #65427 ) ; +#3657 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#3658 = FACE_OUTER_BOUND ( 'NONE', #99655, .T. ) ; +#3659 = EDGE_CURVE ( 'NONE', #77365, #54630, #74179, .T. ) ; +#3660 = ORIENTED_EDGE ( 'NONE', *, *, #54456, .F. ) ; +#3661 = FILL_AREA_STYLE ('',( #11230 ) ) ; +#3662 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3663 = EDGE_LOOP ( 'NONE', ( #34001, #65765, #43523, #91619 ) ) ; +#3664 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14893, 'distance_accuracy_value', 'NONE'); +#3665 = CARTESIAN_POINT ( 'NONE', ( -0.2259284465094109906, -1.087576819458450084, 0.8299999999999999600 ) ) ; +#3666 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#3667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87069 ), #43028 ) ; +#3668 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3669 = CIRCLE ( 'NONE', #31353, 0.05000000000000002359 ) ; +#3670 = ORIENTED_EDGE ( 'NONE', *, *, #89438, .F. ) ; +#3671 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.6761799387799151129, 0.000000000000000000 ) ) ; +#3672 = PLANE ( 'NONE', #99230 ) ; +#3673 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3674 = VERTEX_POINT ( 'NONE', #99061 ) ; +#3675 = LINE ( 'NONE', #56837, #47323 ) ; +#3676 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43091 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69584, #9628, #80695 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3677 = FILL_AREA_STYLE ('',( #50681 ) ) ; +#3678 = VERTEX_POINT ( 'NONE', #51711 ) ; +#3679 = SURFACE_STYLE_FILL_AREA ( #23656 ) ; +#3680 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36284 ), #57508 ) ; +#3681 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3682 = AXIS2_PLACEMENT_3D ( 'NONE', #72237, #56958, #65577 ) ; +#3683 = EDGE_CURVE ( 'NONE', #1880, #38363, #12813, .T. ) ; +#3684 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3685 = FILL_AREA_STYLE ('',( #42008 ) ) ; +#3686 = SURFACE_STYLE_FILL_AREA ( #81335 ) ; +#3687 = ORIENTED_EDGE ( 'NONE', *, *, #23865, .F. ) ; +#3688 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3689 = FACE_OUTER_BOUND ( 'NONE', #6016, .T. ) ; +#3690 = ORIENTED_EDGE ( 'NONE', *, *, #71837, .T. ) ; +#3691 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3692 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28475, 'distance_accuracy_value', 'NONE'); +#3693 = AXIS2_PLACEMENT_3D ( 'NONE', #57370, #39495, #1189 ) ; +#3694 = SURFACE_SIDE_STYLE ('',( #49688 ) ) ; +#3695 = ORIENTED_EDGE ( 'NONE', *, *, #95091, .F. ) ; +#3696 = EDGE_CURVE ( 'NONE', #76911, #15529, #13299, .T. ) ; +#3697 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55826 ) ) ; +#3698 = ORIENTED_EDGE ( 'NONE', *, *, #45905, .T. ) ; +#3699 = SURFACE_STYLE_USAGE ( .BOTH. , #97104 ) ; +#3700 = PLANE ( 'NONE', #49539 ) ; +#3701 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#3702 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3703 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#3704 = CARTESIAN_POINT ( 'NONE', ( 0.2924145224725209768, -0.9822800159449730506, 0.8299999999999999600 ) ) ; +#3705 = EDGE_LOOP ( 'NONE', ( #13519, #50080, #30196, #90327 ) ) ; +#3707 = ORIENTED_EDGE ( 'NONE', *, *, #23106, .T. ) ; +#3706 = ORIENTED_EDGE ( 'NONE', *, *, #5063, .T. ) ; +#3708 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3709 = ORIENTED_EDGE ( 'NONE', *, *, #77534, .T. ) ; +#3710 = FILL_AREA_STYLE_COLOUR ( '', #52431 ) ; +#3711 = STYLED_ITEM ( 'NONE', ( #72936 ), #70671 ) ; +#3712 = VERTEX_POINT ( 'NONE', #76171 ) ; +#3714 = ORIENTED_EDGE ( 'NONE', *, *, #17579, .F. ) ; +#3713 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#3715 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3716 = FACE_OUTER_BOUND ( 'NONE', #5668, .T. ) ; +#3717 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3718 = LINE ( 'NONE', #81369, #4703 ) ; +#3719 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67332 ) ) ; +#3720 = ORIENTED_EDGE ( 'NONE', *, *, #53431, .F. ) ; +#3721 = DIRECTION ( 'NONE', ( 0.3438200982495990266, -0.000000000000000000, -0.9390355371548171348 ) ) ; +#3722 = PRESENTATION_STYLE_ASSIGNMENT (( #80855 ) ) ; +#3723 = ORIENTED_EDGE ( 'NONE', *, *, #77244, .F. ) ; +#3724 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3725 = EDGE_CURVE ( 'NONE', #100039, #46905, #82838, .T. ) ; +#3726 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76400, #74417, #51950, #5907 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#3727 = SURFACE_STYLE_FILL_AREA ( #81378 ) ; +#3728 = LINE ( 'NONE', #74187, #57855 ) ; +#3729 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35991 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59446, #20078, #91041 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3730 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.383333333333333526, 0.000000000000000000 ) ) ; +#3731 = FACE_OUTER_BOUND ( 'NONE', #51906, .T. ) ; +#3732 = VECTOR ( 'NONE', #100364, 1000.000000000000000 ) ; +#3733 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3734 = CARTESIAN_POINT ( 'NONE', ( 1.820901995646819982, -1.357122040133029950, 0.8100000000000000533 ) ) ; +#3735 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3736 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#3737 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#3738 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96708, #26823, #43117, #89098 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#3739 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#3740 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3741 = FILL_AREA_STYLE ('',( #81387 ) ) ; +#3742 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55133 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38664, #93253, #349 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3744 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#3743 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8648700000000000276 ) ) ; +#3745 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47184 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37477, #52302, #43596 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3746 = EDGE_CURVE ( 'NONE', #2708, #39936, #36140, .T. ) ; +#3747 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#3748 = ADVANCED_FACE ( 'NONE', ( #44021 ), #36880, .T. ) ; +#3749 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#3750 = STYLED_ITEM ( 'NONE', ( #12606 ), #35157 ) ; +#3751 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3752 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3753 = ORIENTED_EDGE ( 'NONE', *, *, #42844, .T. ) ; +#3754 = LINE ( 'NONE', #11320, #3895 ) ; +#3755 = AXIS2_PLACEMENT_3D ( 'NONE', #84236, #38768, #91879 ) ; +#3756 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#3758 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79916 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10736, #82787, #44451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3757 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3759 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.405138855653629948, -11.91999999999999993 ) ) ; +#3760 = PLANE ( 'NONE', #44995 ) ; +#3761 = ORIENTED_EDGE ( 'NONE', *, *, #75164, .F. ) ; +#3762 = FILL_AREA_STYLE_COLOUR ( '', #25927 ) ; +#3763 = FILL_AREA_STYLE_COLOUR ( '', #73801 ) ; +#3764 = CARTESIAN_POINT ( 'NONE', ( 1.664835065683850202, -1.443372874996270205, 0.8099999999999976108 ) ) ; +#3765 = CARTESIAN_POINT ( 'NONE', ( -0.2413611859056800091, -1.318798174699070014, 0.8299999999999999600 ) ) ; +#3766 = VECTOR ( 'NONE', #46164, 1000.000000000000000 ) ; +#3767 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51957, #20788, #12555, #74428 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#3768 = ADVANCED_FACE ( 'NONE', ( #67982 ), #58388, .T. ) ; +#3769 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78756 ), #81992 ) ; +#3770 = SURFACE_STYLE_FILL_AREA ( #46685 ) ; +#3771 = SURFACE_SIDE_STYLE ('',( #5221 ) ) ; +#3772 = ORIENTED_EDGE ( 'NONE', *, *, #75234, .F. ) ; +#3773 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3774 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#3775 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3776 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#3777 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3778 = SURFACE_SIDE_STYLE ('',( #96176 ) ) ; +#3779 = SURFACE_STYLE_FILL_AREA ( #2780 ) ; +#3780 = LINE ( 'NONE', #19596, #22030 ) ; +#3781 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36368 ) ) ; +#3782 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3783 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#3784 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3785 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3786 = SURFACE_SIDE_STYLE ('',( #36444 ) ) ; +#3787 = SURFACE_STYLE_USAGE ( .BOTH. , #80406 ) ; +#3788 = PLANE ( 'NONE', #9480 ) ; +#3789 = ORIENTED_EDGE ( 'NONE', *, *, #89831, .T. ) ; +#3790 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#3791 = ORIENTED_EDGE ( 'NONE', *, *, #44296, .F. ) ; +#3792 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3793 = CARTESIAN_POINT ( 'NONE', ( -1.332672534178860779, -1.452480241729792843, 0.8099999999996551070 ) ) ; +#3794 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#3795 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#3796 = STYLED_ITEM ( 'NONE', ( #29792 ), #53210 ) ; +#3797 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#3798 = ORIENTED_EDGE ( 'NONE', *, *, #13893, .F. ) ; +#3799 = FILL_AREA_STYLE_COLOUR ( '', #53092 ) ; +#3800 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3801 = ORIENTED_EDGE ( 'NONE', *, *, #9392, .F. ) ; +#3802 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3803 = VECTOR ( 'NONE', #83666, 1000.000000000000000 ) ; +#3804 = VECTOR ( 'NONE', #16975, 1000.000000000000000 ) ; +#3805 = FILL_AREA_STYLE ('',( #10879 ) ) ; +#3806 = ADVANCED_FACE ( 'NONE', ( #38391 ), #7141, .T. ) ; +#3807 = CARTESIAN_POINT ( 'NONE', ( -1.158596477595430052, -1.445196667902379994, 0.8299999999999999600 ) ) ; +#3808 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999959338, -0.1400000000000000133 ) ) ; +#3809 = EDGE_LOOP ( 'NONE', ( #71003, #44091, #92914, #90248 ) ) ; +#3810 = PRESENTATION_STYLE_ASSIGNMENT (( #36483 ) ) ; +#3811 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#3812 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3813 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77124 ) ) ; +#3814 = AXIS2_PLACEMENT_3D ( 'NONE', #69158, #68681, #85019 ) ; +#3815 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#3816 = ADVANCED_FACE ( 'NONE', ( #23569 ), #39370, .F. ) ; +#3817 = ORIENTED_EDGE ( 'NONE', *, *, #77402, .F. ) ; +#3818 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90261 ) ) ; +#3819 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87158, #48387, #33031 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3820 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3821 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3822 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#3823 = ADVANCED_FACE ( 'NONE', ( #48951 ), #91982, .T. ) ; +#3824 = PLANE ( 'NONE', #67863 ) ; +#3825 = ORIENTED_EDGE ( 'NONE', *, *, #97511, .T. ) ; +#3826 = SURFACE_STYLE_FILL_AREA ( #90092 ) ; +#3827 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7011 ), #75543 ) ; +#3828 = VECTOR ( 'NONE', #15698, 1000.000000000000000 ) ; +#3829 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3830 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71469 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88041, #65538, #34443 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3831 = VERTEX_POINT ( 'NONE', #35656 ) ; +#3832 = ORIENTED_EDGE ( 'NONE', *, *, #27048, .T. ) ; +#3833 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90090, 'distance_accuracy_value', 'NONE'); +#3834 = VECTOR ( 'NONE', #84581, 1000.000000000000000 ) ; +#3835 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3836 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#3837 = PLANE ( 'NONE', #79342 ) ; +#3838 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#3839 = ORIENTED_EDGE ( 'NONE', *, *, #4672, .T. ) ; +#3840 = CARTESIAN_POINT ( 'NONE', ( 1.381066160531370102, -1.463531211619029992, 0.8100000000000000533 ) ) ; +#3841 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3842 = LINE ( 'NONE', #4832, #33388 ) ; +#3843 = CARTESIAN_POINT ( 'NONE', ( 1.071224486614657412, 1.221896575926968653, 0.8100000000000000533 ) ) ; +#3844 = VECTOR ( 'NONE', #45087, 1000.000000000000000 ) ; +#3845 = ORIENTED_EDGE ( 'NONE', *, *, #75041, .T. ) ; +#3847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3846 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5199999999376814230, 0.000000000000000000 ) ) ; +#3848 = ORIENTED_EDGE ( 'NONE', *, *, #60898, .T. ) ; +#3849 = EDGE_CURVE ( 'NONE', #54301, #30201, #66750, .T. ) ; +#3850 = EDGE_CURVE ( 'NONE', #84573, #11284, #88740, .T. ) ; +#3852 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#3851 = CARTESIAN_POINT ( 'NONE', ( 0.1551072701881513194, -1.444195459027963535, 0.8100000000000003864 ) ) ; +#3853 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78014 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86613, #47815, #841 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3854 = ORIENTED_EDGE ( 'NONE', *, *, #25665, .F. ) ; +#3855 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#3856 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3857 = ORIENTED_EDGE ( 'NONE', *, *, #20163, .F. ) ; +#3858 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3859 = VERTEX_POINT ( 'NONE', #96364 ) ; +#3860 = CARTESIAN_POINT ( 'NONE', ( -1.282612376779509900, -1.188596174736179956, 0.8299999999999999600 ) ) ; +#3861 = ADVANCED_FACE ( 'NONE', ( #33635 ), #34145, .T. ) ; +#3862 = SURFACE_STYLE_USAGE ( .BOTH. , #78960 ) ; +#3863 = ADVANCED_FACE ( 'NONE', ( #73438 ), #3489, .T. ) ; +#3864 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#3865 = EDGE_CURVE ( 'NONE', #14832, #26854, #60149, .T. ) ; +#3866 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59389 ) ) ; +#3867 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33258 ), #15268 ) ; +#3868 = SURFACE_SIDE_STYLE ('',( #97753 ) ) ; +#3869 = PRESENTATION_STYLE_ASSIGNMENT (( #27372 ) ) ; +#3870 = ORIENTED_EDGE ( 'NONE', *, *, #48863, .T. ) ; +#3871 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.000000000000000000 ) ) ; +#3872 = STYLED_ITEM ( 'NONE', ( #52622 ), #76417 ) ; +#3873 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#3876 = FACE_OUTER_BOUND ( 'NONE', #34747, .T. ) ; +#3875 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3874 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3877 = SURFACE_SIDE_STYLE ('',( #73839 ) ) ; +#3878 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39945, 'distance_accuracy_value', 'NONE'); +#3879 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#3880 = EDGE_CURVE ( 'NONE', #89973, #6006, #61135, .T. ) ; +#3881 = SURFACE_STYLE_FILL_AREA ( #95775 ) ; +#3882 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7300 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33441, #41099, #56439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3884 = SURFACE_STYLE_USAGE ( .BOTH. , #14005 ) ; +#3885 = ORIENTED_EDGE ( 'NONE', *, *, #13324, .T. ) ; +#3886 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3888 = EDGE_CURVE ( 'NONE', #38810, #38882, #45741, .T. ) ; +#3887 = LINE ( 'NONE', #4385, #41253 ) ; +#3889 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17051 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15649, #8942, #56025 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3890 = STYLED_ITEM ( 'NONE', ( #62680 ), #19299 ) ; +#3891 = FILL_AREA_STYLE ('',( #82025 ) ) ; +#3892 = CARTESIAN_POINT ( 'NONE', ( 0.4526194431797169737, -1.137806428429579908, 0.8300000000000015143 ) ) ; +#3893 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3894 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#3896 = FILL_AREA_STYLE_COLOUR ( '', #51639 ) ; +#3895 = VECTOR ( 'NONE', #11818, 1000.000000000000000 ) ; +#3897 = STYLED_ITEM ( 'NONE', ( #33721 ), #37183 ) ; +#3898 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#3899 = ADVANCED_FACE ( 'NONE', ( #75421 ), #68738, .F. ) ; +#3900 = FILL_AREA_STYLE ('',( #26403 ) ) ; +#3901 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#3902 = LINE ( 'NONE', #57068, #87948 ) ; +#3903 = EDGE_CURVE ( 'NONE', #28251, #84497, #4948, .T. ) ; +#3904 = FILL_AREA_STYLE ('',( #12483 ) ) ; +#3905 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3906 = STYLED_ITEM ( 'NONE', ( #54064 ), #3186 ) ; +#3907 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3908 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#3909 = VECTOR ( 'NONE', #24862, 1000.000000000000000 ) ; +#3910 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3911 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#3912 = SURFACE_STYLE_FILL_AREA ( #19217 ) ; +#3913 = EDGE_LOOP ( 'NONE', ( #63853, #78139, #44881, #46141 ) ) ; +#3914 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3915 = FILL_AREA_STYLE ('',( #41236 ) ) ; +#3916 = VECTOR ( 'NONE', #33726, 1000.000000000000000 ) ; +#3917 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2499999999940882844, -0.2299999999877400114 ) ) ; +#3918 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#3919 = VECTOR ( 'NONE', #20661, 1000.000000000000000 ) ; +#3920 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#3921 = EDGE_CURVE ( 'NONE', #78702, #40674, #36148, .T. ) ; +#3922 = ORIENTED_EDGE ( 'NONE', *, *, #100677, .F. ) ; +#3923 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75992 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20952, #52615, #29121 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3924 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#3925 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#3926 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#3927 = STYLED_ITEM ( 'NONE', ( #71050 ), #53775 ) ; +#3928 = EDGE_CURVE ( 'NONE', #79565, #39998, #75925, .T. ) ; +#3929 = ORIENTED_EDGE ( 'NONE', *, *, #4447, .T. ) ; +#3930 = ORIENTED_EDGE ( 'NONE', *, *, #93958, .F. ) ; +#3931 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3932 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57777 ), #20251 ) ; +#3933 = LINE ( 'NONE', #49410, #36105 ) ; +#3934 = EDGE_LOOP ( 'NONE', ( #72356, #12009, #57604, #8142 ) ) ; +#3935 = CARTESIAN_POINT ( 'NONE', ( 1.814236996624309928, -1.283680827045210027, 0.8300000000000009592 ) ) ; +#3936 = EDGE_CURVE ( 'NONE', #14967, #66816, #83605, .T. ) ; +#3937 = PRESENTATION_STYLE_ASSIGNMENT (( #12017 ) ) ; +#3938 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93606 ), #65982 ) ; +#3939 = STYLED_ITEM ( 'NONE', ( #60240 ), #26490 ) ; +#3940 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#3941 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.100000000000000311, 0.000000000000000000 ) ) ; +#3942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3943 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #96443, #99496 ) ; +#3944 = FILL_AREA_STYLE_COLOUR ( '', #75391 ) ; +#3946 = ORIENTED_EDGE ( 'NONE', *, *, #77726, .T. ) ; +#3945 = EDGE_LOOP ( 'NONE', ( #73272, #80408, #84038, #40812 ) ) ; +#3947 = STYLED_ITEM ( 'NONE', ( #87517 ), #76859 ) ; +#3948 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#3949 = ORIENTED_EDGE ( 'NONE', *, *, #57160, .T. ) ; +#3950 = ORIENTED_EDGE ( 'NONE', *, *, #69266, .F. ) ; +#3951 = LINE ( 'NONE', #35133, #68711 ) ; +#3952 = STYLED_ITEM ( 'NONE', ( #49107 ), #27713 ) ; +#3954 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34967 ) ) ; +#3953 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40696, 'distance_accuracy_value', 'NONE'); +#3955 = CARTESIAN_POINT ( 'NONE', ( 1.892524908602200018, -1.389761831846570095, 0.8299999999999999600 ) ) ; +#3957 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2808578643762690841, -0.1434314575050761598 ) ) ; +#3956 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.000000000000000000 ) ) ; +#3958 = ORIENTED_EDGE ( 'NONE', *, *, #25139, .T. ) ; +#3959 = STYLED_ITEM ( 'NONE', ( #59952 ), #21627 ) ; +#3961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46346 ), #67496 ) ; +#3960 = AXIS2_PLACEMENT_3D ( 'NONE', #44742, #93194, #31463 ) ; +#3962 = VECTOR ( 'NONE', #20070, 1000.000000000000114 ) ; +#3963 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#3964 = VERTEX_POINT ( 'NONE', #44754 ) ; +#3965 = SURFACE_SIDE_STYLE ('',( #65766 ) ) ; +#3966 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90405 ) ) ; +#3967 = ORIENTED_EDGE ( 'NONE', *, *, #92594, .F. ) ; +#3968 = ORIENTED_EDGE ( 'NONE', *, *, #81270, .T. ) ; +#3969 = EDGE_CURVE ( 'NONE', #41162, #20312, #5923, .T. ) ; +#3970 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544766999999999779, 0.8648700000000000276 ) ) ; +#3971 = VECTOR ( 'NONE', #79248, 1000.000000000000000 ) ; +#3973 = FILL_AREA_STYLE_COLOUR ( '', #13975 ) ; +#3972 = SURFACE_SIDE_STYLE ('',( #4947 ) ) ; +#3974 = CARTESIAN_POINT ( 'NONE', ( 1.859836464378280096, -1.220010286732279958, 0.8300000000000004041 ) ) ; +#3975 = FACE_OUTER_BOUND ( 'NONE', #92834, .T. ) ; +#3977 = ORIENTED_EDGE ( 'NONE', *, *, #95542, .T. ) ; +#3976 = PRESENTATION_STYLE_ASSIGNMENT (( #83101 ) ) ; +#3978 = STYLED_ITEM ( 'NONE', ( #32095 ), #3200 ) ; +#3979 = LINE ( 'NONE', #35155, #23783 ) ; +#3980 = ORIENTED_EDGE ( 'NONE', *, *, #92561, .T. ) ; +#3981 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22265 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77693, #54223, #60408 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#3982 = CARTESIAN_POINT ( 'NONE', ( -0.1190035524734260053, -0.9001377335631759458, 0.8100000000000000533 ) ) ; +#3983 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#3984 = ORIENTED_EDGE ( 'NONE', *, *, #93010, .F. ) ; +#3986 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3985 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#3987 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#3988 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#3989 = VERTEX_POINT ( 'NONE', #20799 ) ; +#3990 = EDGE_LOOP ( 'NONE', ( #64718, #10374, #88024, #39894 ) ) ; +#3992 = LINE ( 'NONE', #21312, #86212 ) ; +#3991 = FILL_AREA_STYLE ('',( #58656 ) ) ; +#3993 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.000000000000000000 ) ) ; +#3994 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#3995 = ADVANCED_FACE ( 'NONE', ( #98330 ), #28470, .F. ) ; +#3996 = VECTOR ( 'NONE', #10891, 1000.000000000000114 ) ; +#3997 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#3998 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#3999 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4000 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62324, 'distance_accuracy_value', 'NONE'); +#4001 = ORIENTED_EDGE ( 'NONE', *, *, #11307, .T. ) ; +#4002 = FILL_AREA_STYLE_COLOUR ( '', #93590 ) ; +#4003 = ORIENTED_EDGE ( 'NONE', *, *, #9197, .T. ) ; +#4004 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#4005 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#4006 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#4008 = SURFACE_SIDE_STYLE ('',( #89284 ) ) ; +#4007 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4009 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2419 ) ) ; +#4010 = LINE ( 'NONE', #65809, #71230 ) ; +#4011 = PRESENTATION_STYLE_ASSIGNMENT (( #53862 ) ) ; +#4012 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#4013 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000500, -3.047330906132591704E-17, -1.000000000000000000 ) ) ; +#4014 = FILL_AREA_STYLE ('',( #80142 ) ) ; +#4015 = EDGE_LOOP ( 'NONE', ( #92325, #63046, #81989, #16206 ) ) ; +#4016 = VECTOR ( 'NONE', #58881, 1000.000000000000000 ) ; +#4017 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#4018 = LINE ( 'NONE', #18301, #47677 ) ; +#4019 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000201086, 0.03429000000000000103 ) ) ; +#4020 = SURFACE_SIDE_STYLE ('',( #96415 ) ) ; +#4021 = FILL_AREA_STYLE ('',( #27529 ) ) ; +#4022 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31007, 'distance_accuracy_value', 'NONE'); +#4023 = SURFACE_STYLE_USAGE ( .BOTH. , #75477 ) ; +#4024 = VECTOR ( 'NONE', #11014, 1000.000000000000000 ) ; +#4025 = EDGE_CURVE ( 'NONE', #51666, #20053, #18972, .T. ) ; +#4026 = SURFACE_STYLE_FILL_AREA ( #89791 ) ; +#4027 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666652841, 0.6999999999999999556, 0.000000000000000000 ) ) ; +#4028 = STYLED_ITEM ( 'NONE', ( #60185 ), #28472 ) ; +#4029 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4031 = ORIENTED_EDGE ( 'NONE', *, *, #31499, .T. ) ; +#4030 = AXIS2_PLACEMENT_3D ( 'NONE', #68320, #89807, #60695 ) ; +#4032 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#4033 = CARTESIAN_POINT ( 'NONE', ( 1.512057002305370101, -1.084890943604200020, 0.8100000000000000533 ) ) ; +#4034 = SURFACE_SIDE_STYLE ('',( #66329 ) ) ; +#4035 = VERTEX_POINT ( 'NONE', #40662 ) ; +#4036 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4037 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#4038 = VECTOR ( 'NONE', #88599, 1000.000000000000000 ) ; +#4039 = PRESENTATION_STYLE_ASSIGNMENT (( #73994 ) ) ; +#4040 = LINE ( 'NONE', #27047, #39969 ) ; +#4041 = SURFACE_STYLE_FILL_AREA ( #65319 ) ; +#4042 = ORIENTED_EDGE ( 'NONE', *, *, #56806, .T. ) ; +#4043 = EDGE_CURVE ( 'NONE', #9858, #56508, #64144, .T. ) ; +#4044 = ORIENTED_EDGE ( 'NONE', *, *, #63740, .F. ) ; +#4045 = SURFACE_SIDE_STYLE ('',( #95434 ) ) ; +#4046 = STYLED_ITEM ( 'NONE', ( #29453 ), #3336 ) ; +#4047 = CARTESIAN_POINT ( 'NONE', ( -0.8280235389610388630, 0.6899999999999999467, -6.098637220230962441E-17 ) ) ; +#4048 = SURFACE_SIDE_STYLE ('',( #82186 ) ) ; +#4049 = PLANE ( 'NONE', #54823 ) ; +#4050 = PLANE ( 'NONE', #18458 ) ; +#4051 = CARTESIAN_POINT ( 'NONE', ( -0.4517732017275800094, -1.126314109036339994, 0.8100000000000000533 ) ) ; +#4052 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75770 ) ) ; +#4053 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4054 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4055 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8099999999999776268 ) ) ; +#4056 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#4057 = ADVANCED_FACE ( 'NONE', ( #94741 ), #85086, .T. ) ; +#4058 = SURFACE_SIDE_STYLE ('',( #34732 ) ) ; +#4059 = ORIENTED_EDGE ( 'NONE', *, *, #22877, .T. ) ; +#4060 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66021 ) ) ; +#4061 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4062 = ORIENTED_EDGE ( 'NONE', *, *, #93966, .T. ) ; +#4063 = FACE_OUTER_BOUND ( 'NONE', #41982, .T. ) ; +#4064 = SURFACE_STYLE_FILL_AREA ( #56718 ) ; +#4065 = SURFACE_STYLE_USAGE ( .BOTH. , #26565 ) ; +#4066 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#4067 = LINE ( 'NONE', #12666, #7173 ) ; +#4068 = CARTESIAN_POINT ( 'NONE', ( -1.031006683134279900, -1.010360997253880067, 0.8299999999999999600 ) ) ; +#4069 = CARTESIAN_POINT ( 'NONE', ( -0.4535372177072710120, -0.9179759943635570352, 0.8100000000000000533 ) ) ; +#4070 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#4071 = VECTOR ( 'NONE', #94788, 1000.000000000000000 ) ; +#4074 = ORIENTED_EDGE ( 'NONE', *, *, #68844, .F. ) ; +#4073 = ORIENTED_EDGE ( 'NONE', *, *, #91014, .F. ) ; +#4072 = VECTOR ( 'NONE', #47195, 1000.000000000000000 ) ; +#4075 = EDGE_CURVE ( 'NONE', #96590, #30427, #78939, .T. ) ; +#4076 = ORIENTED_EDGE ( 'NONE', *, *, #29693, .F. ) ; +#4077 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4078 = STYLED_ITEM ( 'NONE', ( #77486 ), #89634 ) ; +#4079 = VECTOR ( 'NONE', #88642, 1000.000000000000000 ) ; +#4080 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4081 = ORIENTED_EDGE ( 'NONE', *, *, #99256, .F. ) ; +#4082 = ADVANCED_FACE ( 'NONE', ( #32993 ), #24863, .F. ) ; +#4083 = ORIENTED_EDGE ( 'NONE', *, *, #56905, .F. ) ; +#4084 = LINE ( 'NONE', #97486, #87322 ) ; +#4085 = PRESENTATION_STYLE_ASSIGNMENT (( #97949 ) ) ; +#4086 = AXIS2_PLACEMENT_3D ( 'NONE', #59266, #37749, #29572 ) ; +#4087 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4088 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#4089 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4090 = ORIENTED_EDGE ( 'NONE', *, *, #25361, .T. ) ; +#4091 = VERTEX_POINT ( 'NONE', #96256 ) ; +#4092 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72757 ) ) ; +#4093 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44870 ), #95378 ) ; +#4094 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4095 = ORIENTED_EDGE ( 'NONE', *, *, #69679, .T. ) ; +#4096 = EDGE_CURVE ( 'NONE', #99432, #690, #58028, .T. ) ; +#4097 = EDGE_CURVE ( 'NONE', #26955, #67425, #49321, .T. ) ; +#4098 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97207 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25693, #19004, #9267 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4100 = EDGE_CURVE ( 'NONE', #11081, #90194, #19680, .T. ) ; +#4099 = VERTEX_POINT ( 'NONE', #81985 ) ; +#4101 = EDGE_CURVE ( 'NONE', #39192, #54213, #87614, .T. ) ; +#4102 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4103 = SURFACE_STYLE_FILL_AREA ( #49584 ) ; +#4104 = ORIENTED_EDGE ( 'NONE', *, *, #69636, .T. ) ; +#4106 = CARTESIAN_POINT ( 'NONE', ( -0.08371903756181429956, -1.220939016933670018, 0.8100000000000000533 ) ) ; +#4105 = AXIS2_PLACEMENT_3D ( 'NONE', #36206, #5012, #44822 ) ; +#4107 = LINE ( 'NONE', #35785, #91729 ) ; +#4108 = ORIENTED_EDGE ( 'NONE', *, *, #24565, .T. ) ; +#4109 = EDGE_LOOP ( 'NONE', ( #64268, #70488, #98560, #53353 ) ) ; +#4110 = ORIENTED_EDGE ( 'NONE', *, *, #40595, .F. ) ; +#4111 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#4112 = VECTOR ( 'NONE', #49859, 1000.000000000000114 ) ; +#4113 = CARTESIAN_POINT ( 'NONE', ( 0.2448740894508923960, -1.060849306175230211, 0.8100000000000000533 ) ) ; +#4114 = ADVANCED_FACE ( 'NONE', ( #57509 ), #41169, .F. ) ; +#4115 = SURFACE_SIDE_STYLE ('',( #74065 ) ) ; +#4116 = CARTESIAN_POINT ( 'NONE', ( -1.297607782917340025, -1.181386160465659918, 0.8300000000000000711 ) ) ; +#4117 = FACE_OUTER_BOUND ( 'NONE', #73467, .T. ) ; +#4118 = EDGE_CURVE ( 'NONE', #97394, #46953, #96750, .T. ) ; +#4119 = AXIS2_PLACEMENT_3D ( 'NONE', #90135, #45645, #76831 ) ; +#4120 = PLANE ( 'NONE', #96531 ) ; +#4121 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.000000000000000000 ) ) ; +#4122 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000006176, -0.1499999999999999944 ) ) ; +#4123 = EDGE_LOOP ( 'NONE', ( #42915, #30432, #65940, #23054 ) ) ; +#4124 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -3.500000000000000444, 1.308546363094771468E-78 ) ) ; +#4125 = VERTEX_POINT ( 'NONE', #73812 ) ; +#4126 = AXIS2_PLACEMENT_3D ( 'NONE', #32360, #15478, #77283 ) ; +#4127 = LINE ( 'NONE', #96521, #72969 ) ; +#4128 = CARTESIAN_POINT ( 'NONE', ( -0.7059659090909090606, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#4129 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#4130 = PRESENTATION_STYLE_ASSIGNMENT (( #74085 ) ) ; +#4132 = SURFACE_STYLE_USAGE ( .BOTH. , #65397 ) ; +#4131 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1458578643762690474 ) ) ; +#4133 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4134 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4135 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4136 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#4137 = FACE_OUTER_BOUND ( 'NONE', #57256, .T. ) ; +#4138 = VECTOR ( 'NONE', #51985, 1000.000000000000000 ) ; +#4139 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#4140 = ORIENTED_EDGE ( 'NONE', *, *, #72730, .F. ) ; +#4141 = FILL_AREA_STYLE ('',( #43442 ) ) ; +#4142 = STYLED_ITEM ( 'NONE', ( #56648 ), #29956 ) ; +#4144 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4143 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#4145 = PLANE ( 'NONE', #71717 ) ; +#4146 = EDGE_CURVE ( 'NONE', #5115, #78892, #59784, .T. ) ; +#4147 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.251909075926969983, 0.8100000000000000533 ) ) ; +#4148 = AXIS2_PLACEMENT_3D ( 'NONE', #54619, #55625, #23448 ) ; +#4149 = AXIS2_PLACEMENT_3D ( 'NONE', #14790, #21494, #83798 ) ; +#4150 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8944 ) ) ; +#4151 = EDGE_CURVE ( 'NONE', #27482, #77365, #41674, .T. ) ; +#4152 = EDGE_LOOP ( 'NONE', ( #97249, #5670, #98839, #34174 ) ) ; +#4153 = FILL_AREA_STYLE_COLOUR ( '', #91327 ) ; +#4154 = SURFACE_STYLE_FILL_AREA ( #74110 ) ; +#4155 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 1.306104834247010004E-29 ) ) ; +#4156 = SURFACE_SIDE_STYLE ('',( #2659 ) ) ; +#4157 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4158 = VECTOR ( 'NONE', #14591, 1000.000000000000000 ) ; +#4159 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99164 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87408, #55292, #63938 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4160 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#4162 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4161 = VECTOR ( 'NONE', #54333, 1000.000000000000000 ) ; +#4163 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#4164 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4165 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #34554, #4369 ), + ( #20185, #51368 ), + ( #81010, #19701 ), + ( #57035, #97754 ), + ( #27894, #80493 ), + ( #59047, #12456 ), + ( #43662, #34039 ), + ( #18153, #57532 ), + ( #49342, #10421 ), + ( #41692, #10949 ), + ( #73341, #2888 ), + ( #65158, #3388 ), + ( #51865, #60044 ), + ( #84483, #99695 ), + ( #60540, #12965 ), + ( #76827, #90655 ), + ( #5831, #91148 ), + ( #29367, #53350 ), + ( #44171, #92613 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07045709961185059322, 0.1383447481512529997, 0.2028990021023250045, 0.2654810950381230050, 0.3258772383107860215, 0.3852050427271530020, 0.4429358768679569902, 0.5002805841468770387, 0.5571221970013150449, 0.6137119875414840386, 0.6717416701598919460, 0.7307879491163220553, 0.7928531519886019563, 0.8578850024924840056, 0.9271793188984439604, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4166 = STYLED_ITEM ( 'NONE', ( #83711 ), #77591 ) ; +#4167 = ORIENTED_EDGE ( 'NONE', *, *, #99169, .F. ) ; +#4168 = VERTEX_POINT ( 'NONE', #10926 ) ; +#4169 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#4170 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59072, 'distance_accuracy_value', 'NONE'); +#4171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21112, 'distance_accuracy_value', 'NONE'); +#4172 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8648700000000000276 ) ) ; +#4173 = CARTESIAN_POINT ( 'NONE', ( -0.2194392452033120111, -1.042364979248350032, 0.8100000000000000533 ) ) ; +#4174 = CIRCLE ( 'NONE', #25415, 0.05000000000000002359 ) ; +#4175 = SURFACE_STYLE_USAGE ( .BOTH. , #65445 ) ; +#4176 = LINE ( 'NONE', #64463, #19108 ) ; +#4177 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4178 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.36999999999999922 ) ) ; +#4179 = AXIS2_PLACEMENT_3D ( 'NONE', #26180, #42495, #74642 ) ; +#4180 = LINE ( 'NONE', #99011, #64119 ) ; +#4181 = ORIENTED_EDGE ( 'NONE', *, *, #17631, .F. ) ; +#4182 = EDGE_CURVE ( 'NONE', #66870, #6703, #2675, .T. ) ; +#4183 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4184 = ORIENTED_EDGE ( 'NONE', *, *, #63698, .F. ) ; +#4185 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97081 ) ) ; +#4186 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4187 = ORIENTED_EDGE ( 'NONE', *, *, #78859, .F. ) ; +#4188 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4189 = SURFACE_STYLE_USAGE ( .BOTH. , #10238 ) ; +#4190 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#4191 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81314 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60870, #100026, #30181 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4192 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4193 = PLANE ( 'NONE', #91501 ) ; +#4194 = FILL_AREA_STYLE ('',( #51181 ) ) ; +#4195 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#4196 = ORIENTED_EDGE ( 'NONE', *, *, #85109, .T. ) ; +#4197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4198 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4199 = ORIENTED_EDGE ( 'NONE', *, *, #86591, .T. ) ; +#4200 = VECTOR ( 'NONE', #9757, 1000.000000000000114 ) ; +#4201 = FACE_OUTER_BOUND ( 'NONE', #35145, .T. ) ; +#4202 = SURFACE_STYLE_FILL_AREA ( #74159 ) ; +#4203 = VERTEX_POINT ( 'NONE', #97735 ) ; +#4204 = ORIENTED_EDGE ( 'NONE', *, *, #74381, .T. ) ; +#4205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4206 = PLANE ( 'NONE', #48167 ) ; +#4207 = FILL_AREA_STYLE ('',( #90474 ) ) ; +#4208 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5199999998808380042, 0.000000000000000000 ) ) ; +#4209 = ORIENTED_EDGE ( 'NONE', *, *, #96203, .F. ) ; +#4211 = ORIENTED_EDGE ( 'NONE', *, *, #93809, .T. ) ; +#4210 = VERTEX_POINT ( 'NONE', #89129 ) ; +#4212 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999993339, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#4213 = ORIENTED_EDGE ( 'NONE', *, *, #1934, .F. ) ; +#4214 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#4215 = VECTOR ( 'NONE', #37165, 1000.000000000000000 ) ; +#4216 = ORIENTED_EDGE ( 'NONE', *, *, #18550, .T. ) ; +#4218 = ORIENTED_EDGE ( 'NONE', *, *, #59214, .T. ) ; +#4217 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4219 = EDGE_CURVE ( 'NONE', #27976, #29795, #19159, .T. ) ; +#4220 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19764 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19689, #82981, #98707 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4221 = LINE ( 'NONE', #13298, #62248 ) ; +#4222 = VECTOR ( 'NONE', #87142, 1000.000000000000000 ) ; +#4224 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#4223 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27061 ), #17248 ) ; +#4225 = ORIENTED_EDGE ( 'NONE', *, *, #37162, .T. ) ; +#4226 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597373283, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#4227 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4228 = ORIENTED_EDGE ( 'NONE', *, *, #66771, .T. ) ; +#4229 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4230 = DIRECTION ( 'NONE', ( 1.617781153285274011E-32, 1.000000000000000000, -5.551115123125780237E-17 ) ) ; +#4231 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100362 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1332, #9901, #80464 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4232 = STYLED_ITEM ( 'NONE', ( #73499 ), #89516 ) ; +#4233 = LINE ( 'NONE', #97618, #716 ) ; +#4234 = SURFACE_SIDE_STYLE ('',( #89010 ) ) ; +#4235 = PLANE ( 'NONE', #73082 ) ; +#4236 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58070 ), #95522 ) ; +#4237 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4238 = EDGE_CURVE ( 'NONE', #12266, #12804, #11427, .T. ) ; +#4239 = CARTESIAN_POINT ( 'NONE', ( 1.697893922398610034, -1.445363849546990043, 0.8299999999999999600 ) ) ; +#4240 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4241 = PLANE ( 'NONE', #86628 ) ; +#4242 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79245 ), #67906 ) ; +#4243 = EDGE_LOOP ( 'NONE', ( #39878, #20390, #7780, #75451 ) ) ; +#4244 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4245 = LINE ( 'NONE', #41185, #84160 ) ; +#4246 = VECTOR ( 'NONE', #57202, 1000.000000000000000 ) ; +#4247 = CARTESIAN_POINT ( 'NONE', ( 1.394831661730270067, -1.224577966852969935, 0.8300000000000022915 ) ) ; +#4248 = VECTOR ( 'NONE', #33329, 1000.000000000000114 ) ; +#4249 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8648700000000000276 ) ) ; +#4250 = CARTESIAN_POINT ( 'NONE', ( -0.1408076298701300133, -1.164935064935070042, 0.8100000000000000533 ) ) ; +#4251 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.149999999999959499, 0.000000000000000000 ) ) ; +#4252 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#4253 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#4254 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.500000000000000000, 0.000000000000000000 ) ) ; +#4255 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#4256 = ORIENTED_EDGE ( 'NONE', *, *, #33188, .T. ) ; +#4257 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.266666666666659946, 0.000000000000000000 ) ) ; +#4258 = LINE ( 'NONE', #19056, #2287 ) ; +#4259 = LINE ( 'NONE', #27265, #76003 ) ; +#4260 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75135 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85316, #93457, #74044 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4261 = ORIENTED_EDGE ( 'NONE', *, *, #90406, .F. ) ; +#4262 = EDGE_CURVE ( 'NONE', #10764, #32276, #88496, .T. ) ; +#4263 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4264 = FILL_AREA_STYLE_COLOUR ( '', #55297 ) ; +#4265 = SURFACE_SIDE_STYLE ('',( #82392 ) ) ; +#4266 = CARTESIAN_POINT ( 'NONE', ( 1.566818635346699962, -1.328064047174219997, 0.8099999999999976108 ) ) ; +#4267 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9068 ), #98704 ) ; +#4268 = CARTESIAN_POINT ( 'NONE', ( -0.1683685331939580310, -1.436594792639700024, 0.8100000000000000533 ) ) ; +#4269 = LINE ( 'NONE', #51246, #90400 ) ; +#4270 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18905 ) ) ; +#4271 = EDGE_CURVE ( 'NONE', #89045, #7937, #91131, .T. ) ; +#4272 = ORIENTED_EDGE ( 'NONE', *, *, #5685, .T. ) ; +#4273 = FILL_AREA_STYLE ('',( #49760 ) ) ; +#4274 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58272, #26605, #35288, #97503 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4275 = PLANE ( 'NONE', #14746 ) ; +#4276 = FILL_AREA_STYLE_COLOUR ( '', #69257 ) ; +#4277 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4278 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#4279 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#4280 = LINE ( 'NONE', #58454, #91461 ) ; +#4281 = FILL_AREA_STYLE ('',( #27795 ) ) ; +#4282 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4283 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87292, 'distance_accuracy_value', 'NONE'); +#4284 = SURFACE_STYLE_USAGE ( .BOTH. , #81917 ) ; +#4285 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.1000000000000000056, -13.35000000000000142 ) ) ; +#4286 = VECTOR ( 'NONE', #93236, 1000.000000000000000 ) ; +#4287 = ORIENTED_EDGE ( 'NONE', *, *, #47069, .F. ) ; +#4288 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4289 = ORIENTED_EDGE ( 'NONE', *, *, #90588, .T. ) ; +#4290 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79427, 'distance_accuracy_value', 'NONE'); +#4291 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18356, 'distance_accuracy_value', 'NONE'); +#4292 = FILL_AREA_STYLE_COLOUR ( '', #40640 ) ; +#4293 = LINE ( 'NONE', #75255, #60891 ) ; +#4294 = FILL_AREA_STYLE ('',( #12374 ) ) ; +#4295 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4296 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46673, #17536, #70163 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4297 = PRESENTATION_STYLE_ASSIGNMENT (( #74251 ) ) ; +#4298 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76401 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60801, #37313, #68416 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4299 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#4300 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#4301 = ORIENTED_EDGE ( 'NONE', *, *, #98361, .F. ) ; +#4303 = PRESENTATION_STYLE_ASSIGNMENT (( #74258 ) ) ; +#4302 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22220 ), #62996 ) ; +#4304 = EDGE_CURVE ( 'NONE', #28448, #28730, #53337, .T. ) ; +#4305 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16512, 'distance_accuracy_value', 'NONE'); +#4306 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63065 ) ) ; +#4307 = CARTESIAN_POINT ( 'NONE', ( 8.404300249749912410, 1.979081249749912397, 0.8991599999999999593 ) ) ; +#4308 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4309 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9106 ), #74508 ) ; +#4310 = VECTOR ( 'NONE', #46354, 1000.000000000000000 ) ; +#4311 = ORIENTED_EDGE ( 'NONE', *, *, #90905, .T. ) ; +#4312 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#4313 = EDGE_CURVE ( 'NONE', #13965, #777, #60519, .T. ) ; +#4314 = CARTESIAN_POINT ( 'NONE', ( 1.213600188310800077, -1.515470133326519919, 0.8299999999999994049 ) ) ; +#4315 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4316 = FILL_AREA_STYLE_COLOUR ( '', #60488 ) ; +#4317 = ORIENTED_EDGE ( 'NONE', *, *, #56468, .F. ) ; +#4318 = SURFACE_SIDE_STYLE ('',( #89590 ) ) ; +#4319 = FILL_AREA_STYLE ('',( #74270 ) ) ; +#4320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72085, 'distance_accuracy_value', 'NONE'); +#4321 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4322 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4323 = EDGE_CURVE ( 'NONE', #37710, #44029, #51607, .T. ) ; +#4324 = EDGE_LOOP ( 'NONE', ( #52317, #67387, #16122, #36037 ) ) ; +#4325 = ADVANCED_FACE ( 'NONE', ( #52348 ), #68121, .T. ) ; +#4326 = VECTOR ( 'NONE', #38296, 1000.000000000000000 ) ; +#4327 = AXIS2_PLACEMENT_3D ( 'NONE', #56456, #24295, #16067 ) ; +#4328 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#4329 = LINE ( 'NONE', #29314, #9675 ) ; +#4330 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#4331 = CARTESIAN_POINT ( 'NONE', ( -1.201896076711291395, -1.213996294333074655, 0.8099999999998303002 ) ) ; +#4332 = SURFACE_STYLE_FILL_AREA ( #51317 ) ; +#4333 = ORIENTED_EDGE ( 'NONE', *, *, #22532, .T. ) ; +#4334 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83296 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39500, #8773, #41047 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4335 = VECTOR ( 'NONE', #75806, 1000.000000000000000 ) ; +#4336 = VERTEX_POINT ( 'NONE', #67618 ) ; +#4337 = ORIENTED_EDGE ( 'NONE', *, *, #93107, .T. ) ; +#4339 = ADVANCED_FACE ( 'NONE', ( #44640 ), #36027, .T. ) ; +#4338 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4340 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #10708, #12737, #98001, #89411, #59820, #97035, #41963, #66430 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000000000, 0.5000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4342 = CARTESIAN_POINT ( 'NONE', ( -1.284259234833809993, -1.485874691073119980, 0.8299999999999999600 ) ) ; +#4341 = PRESENTATION_STYLE_ASSIGNMENT (( #90616 ) ) ; +#4343 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#4344 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#4345 = ORIENTED_EDGE ( 'NONE', *, *, #10696, .F. ) ; +#4346 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -11.41999999999999993 ) ) ; +#4347 = AXIS2_PLACEMENT_3D ( 'NONE', #77008, #85163, #37232 ) ; +#4348 = VERTEX_POINT ( 'NONE', #29835 ) ; +#4349 = AXIS2_PLACEMENT_3D ( 'NONE', #13727, #30098, #7544 ) ; +#4350 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.32344800000000085, 0.8648700000000000276 ) ) ; +#4351 = ORIENTED_EDGE ( 'NONE', *, *, #47070, .T. ) ; +#4353 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4352 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4354 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33682 ) ) ; +#4355 = ORIENTED_EDGE ( 'NONE', *, *, #37174, .T. ) ; +#4356 = STYLED_ITEM ( 'NONE', ( #65067 ), #83982 ) ; +#4357 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4358 = SURFACE_SIDE_STYLE ('',( #11436 ) ) ; +#4359 = EDGE_LOOP ( 'NONE', ( #44767, #69321, #11400, #75450 ) ) ; +#4360 = ORIENTED_EDGE ( 'NONE', *, *, #19145, .F. ) ; +#4361 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4362 = CARTESIAN_POINT ( 'NONE', ( -1.036585239840499995, -1.260670644472420054, 0.8299999999999999600 ) ) ; +#4363 = AXIS2_PLACEMENT_3D ( 'NONE', #100823, #30474, #63696 ) ; +#4364 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#4365 = AXIS2_PLACEMENT_3D ( 'NONE', #82979, #11435, #19686 ) ; +#4366 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#4367 = CYLINDRICAL_SURFACE ( 'NONE', #93149, 0.04999999999999991257 ) ; +#4368 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.000000000000000000, 1.149999999999999911 ) ) ; +#4369 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#4370 = ORIENTED_EDGE ( 'NONE', *, *, #47907, .F. ) ; +#4371 = EDGE_CURVE ( 'NONE', #5017, #41410, #44153, .T. ) ; +#4372 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4373 = FILL_AREA_STYLE ('',( #74336 ) ) ; +#4374 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4376 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4375 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#4377 = VECTOR ( 'NONE', #65301, 1000.000000000000000 ) ; +#4378 = FILL_AREA_STYLE ('',( #81022 ) ) ; +#4379 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999920064, 1.899999999999980149, -0.02000000000000000042 ) ) ; +#4380 = CLOSED_SHELL ( 'NONE', ( #2064, #78737, #88366, #92090, #69659, #44691 ) ) ; +#4381 = FACE_OUTER_BOUND ( 'NONE', #26224, .T. ) ; +#4382 = EDGE_CURVE ( 'NONE', #21633, #49085, #17367, .T. ) ; +#4383 = ORIENTED_EDGE ( 'NONE', *, *, #92693, .T. ) ; +#4384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87926 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28993, #66304, #19321 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4385 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 8.003631000000000384, 0.8991599999999999593 ) ) ; +#4386 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4387 = AXIS2_PLACEMENT_3D ( 'NONE', #22633, #12881, #21622 ) ; +#4388 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4389 = SURFACE_STYLE_USAGE ( .BOTH. , #58568 ) ; +#4390 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4391 = SURFACE_STYLE_FILL_AREA ( #20722 ) ; +#4392 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58310 ), #46795 ) ; +#4393 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#4394 = VECTOR ( 'NONE', #15871, 1000.000000000000000 ) ; +#4395 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8648700000000000276 ) ) ; +#4396 = SURFACE_STYLE_FILL_AREA ( #3904 ) ; +#4397 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4398 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#4399 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50324, 'distance_accuracy_value', 'NONE'); +#4400 = PRESENTATION_STYLE_ASSIGNMENT (( #74372 ) ) ; +#4401 = CARTESIAN_POINT ( 'NONE', ( -0.2880456131010220022, -1.031932509624869931, 0.8300000000000009592 ) ) ; +#4402 = PLANE ( 'NONE', #9127 ) ; +#4403 = DIRECTION ( 'NONE', ( 0.7071067811865465735, 0.7071067811865484609, 0.000000000000000000 ) ) ; +#4404 = SURFACE_SIDE_STYLE ('',( #3912 ) ) ; +#4405 = VERTEX_POINT ( 'NONE', #76806 ) ; +#4406 = FILL_AREA_STYLE_COLOUR ( '', #63284 ) ; +#4407 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75790, 'distance_accuracy_value', 'NONE'); +#4408 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63185, 'distance_accuracy_value', 'NONE'); +#4409 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51682 ) ) ; +#4411 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#4410 = SURFACE_SIDE_STYLE ('',( #73382 ) ) ; +#4412 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5388 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18291, #79115, #992 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4413 = EDGE_CURVE ( 'NONE', #70520, #35481, #6771, .T. ) ; +#4414 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4415 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28838 ) ) ; +#4416 = VERTEX_POINT ( 'NONE', #12438 ) ; +#4417 = FILL_AREA_STYLE ('',( #48903 ) ) ; +#4418 = ORIENTED_EDGE ( 'NONE', *, *, #46616, .T. ) ; +#4419 = FILL_AREA_STYLE_COLOUR ( '', #35100 ) ; +#4420 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31847, 'distance_accuracy_value', 'NONE'); +#4422 = LINE ( 'NONE', #27949, #67344 ) ; +#4421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82718 ), #37106 ) ; +#4423 = AXIS2_PLACEMENT_3D ( 'NONE', #22865, #91771, #53996 ) ; +#4424 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10818, 'distance_accuracy_value', 'NONE'); +#4425 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4426 = ADVANCED_FACE ( 'NONE', ( #43642 ), #4837, .T. ) ; +#4427 = ORIENTED_EDGE ( 'NONE', *, *, #37808, .T. ) ; +#4428 = ORIENTED_EDGE ( 'NONE', *, *, #69370, .F. ) ; +#4429 = ADVANCED_FACE ( 'NONE', ( #46134 ), #54866, .T. ) ; +#4430 = SURFACE_STYLE_USAGE ( .BOTH. , #99291 ) ; +#4431 = ORIENTED_EDGE ( 'NONE', *, *, #73236, .F. ) ; +#4432 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#4433 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74578 ) ) ; +#4434 = ADVANCED_FACE ( 'NONE', ( #22692 ), #7287, .T. ) ; +#4435 = SURFACE_STYLE_USAGE ( .BOTH. , #50940 ) ; +#4436 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.41999999999999993 ) ) ; +#4437 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#4439 = ORIENTED_EDGE ( 'NONE', *, *, #74639, .F. ) ; +#4438 = ORIENTED_EDGE ( 'NONE', *, *, #24421, .F. ) ; +#4440 = AXIS2_PLACEMENT_3D ( 'NONE', #24535, #85256, #69925 ) ; +#4441 = ORIENTED_EDGE ( 'NONE', *, *, #12185, .T. ) ; +#4442 = VERTEX_POINT ( 'NONE', #15495 ) ; +#4443 = LINE ( 'NONE', #51459, #16522 ) ; +#4444 = FILL_AREA_STYLE ('',( #53441 ) ) ; +#4445 = CIRCLE ( 'NONE', #43581, 0.1099999999999998479 ) ; +#4446 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78027 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15961, #61973, #24694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4447 = EDGE_CURVE ( 'NONE', #80977, #37668, #15745, .T. ) ; +#4448 = SURFACE_STYLE_FILL_AREA ( #28942 ) ; +#4450 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2808578643762690286, -0.1500000000000000222 ) ) ; +#4449 = SURFACE_SIDE_STYLE ('',( #67240 ) ) ; +#4451 = EDGE_LOOP ( 'NONE', ( #64325, #88852, #58254, #54355 ) ) ; +#4452 = CLOSED_SHELL ( 'NONE', ( #34745, #51997, #23463, #40942, #56483, #65893 ) ) ; +#4454 = VECTOR ( 'NONE', #22723, 1000.000000000000114 ) ; +#4453 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4455 = EDGE_CURVE ( 'NONE', #50096, #46055, #81869, .T. ) ; +#4456 = FACE_OUTER_BOUND ( 'NONE', #69760, .T. ) ; +#4457 = VECTOR ( 'NONE', #70461, 1000.000000000000000 ) ; +#4458 = CARTESIAN_POINT ( 'NONE', ( -1.343981097684900039, -0.9654894655288509542, 0.8100000000000000533 ) ) ; +#4459 = ORIENTED_EDGE ( 'NONE', *, *, #94271, .T. ) ; +#4461 = PRESENTATION_STYLE_ASSIGNMENT (( #74435 ) ) ; +#4460 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#4462 = EDGE_LOOP ( 'NONE', ( #35633, #42394, #11741, #17841, #5161, #23535 ) ) ; +#4463 = ORIENTED_EDGE ( 'NONE', *, *, #83980, .F. ) ; +#4464 = ADVANCED_FACE ( 'NONE', ( #41550 ), #17520, .T. ) ; +#4465 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 0.8999999999999991340, -5.977360615245821520E-90 ) ) ; +#4467 = ORIENTED_EDGE ( 'NONE', *, *, #60884, .F. ) ; +#4466 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4468 = SURFACE_STYLE_FILL_AREA ( #64256 ) ; +#4469 = ORIENTED_EDGE ( 'NONE', *, *, #35336, .F. ) ; +#4470 = EDGE_CURVE ( 'NONE', #88578, #74415, #2746, .T. ) ; +#4471 = PRESENTATION_STYLE_ASSIGNMENT (( #58148 ) ) ; +#4472 = VERTEX_POINT ( 'NONE', #42551 ) ; +#4474 = SURFACE_SIDE_STYLE ('',( #27488 ) ) ; +#4473 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4475 = FILL_AREA_STYLE_COLOUR ( '', #10169 ) ; +#4476 = ORIENTED_EDGE ( 'NONE', *, *, #7295, .T. ) ; +#4477 = ORIENTED_EDGE ( 'NONE', *, *, #99789, .F. ) ; +#4480 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4479 = CARTESIAN_POINT ( 'NONE', ( 0.5450788742336990511, -1.052784384528720141, 0.8299999999999992939 ) ) ; +#4478 = PRODUCT_DEFINITION ( 'δ֪', '', #76335, #96310 ) ; +#4481 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4482 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91303 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65462, #80822, #89469 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4483 = PRESENTATION_STYLE_ASSIGNMENT (( #43795 ) ) ; +#4484 = FACE_OUTER_BOUND ( 'NONE', #87807, .T. ) ; +#4485 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#4486 = VECTOR ( 'NONE', #24387, 1000.000000000000000 ) ; +#4487 = ORIENTED_EDGE ( 'NONE', *, *, #51278, .T. ) ; +#4488 = EDGE_CURVE ( 'NONE', #188, #2612, #11303, .T. ) ; +#4489 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#4490 = ORIENTED_EDGE ( 'NONE', *, *, #94556, .T. ) ; +#4491 = CARTESIAN_POINT ( 'NONE', ( 1.425641884052289976, -1.263266231710209908, 0.8100000000000000533 ) ) ; +#4492 = SURFACE_SIDE_STYLE ('',( #17800 ) ) ; +#4493 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9507 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35717, #50543, #75990 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4494 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#4495 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.000000000000000000 ) ) ; +#4496 = PRESENTATION_STYLE_ASSIGNMENT (( #96405 ) ) ; +#4497 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#4498 = EDGE_CURVE ( 'NONE', #81461, #77789, #34908, .T. ) ; +#4500 = EDGE_LOOP ( 'NONE', ( #75079, #49998, #48580, #83821 ) ) ; +#4499 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4501 = LINE ( 'NONE', #35689, #26527 ) ; +#4502 = SURFACE_SIDE_STYLE ('',( #12096 ) ) ; +#4503 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#4504 = LINE ( 'NONE', #96916, #52849 ) ; +#4505 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#4506 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8991599999999999593 ) ) ; +#4507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43636 ) ) ; +#4508 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4509 = ADVANCED_FACE ( 'NONE', ( #25252 ), #72180, .T. ) ; +#4510 = DIRECTION ( 'NONE', ( -0.7071062811868784603, -0.7071072811858630791, 0.000000000000000000 ) ) ; +#4511 = VECTOR ( 'NONE', #87111, 1000.000000000000000 ) ; +#4512 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4513 = STYLED_ITEM ( 'NONE', ( #74493 ), #62640 ) ; +#4514 = EDGE_CURVE ( 'NONE', #40281, #38757, #64525, .T. ) ; +#4515 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.09999999999999853451, 0.1829999999999749605 ) ) ; +#4516 = AXIS2_PLACEMENT_3D ( 'NONE', #61358, #92437, #44466 ) ; +#4517 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4518 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94116 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61219, #13138, #37717 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4519 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62319, 'distance_accuracy_value', 'NONE'); +#4520 = EDGE_LOOP ( 'NONE', ( #55611, #58840, #96261, #39646 ) ) ; +#4521 = CLOSED_SHELL ( 'NONE', ( #66915, #68289, #65770, #47804, #73206, #66791 ) ) ; +#4522 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4523 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4524 = VERTEX_POINT ( 'NONE', #52237 ) ; +#4525 = LINE ( 'NONE', #88804, #44585 ) ; +#4526 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4527 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33828 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13750, #98490, #6081 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4528 = VECTOR ( 'NONE', #51565, 1000.000000000000000 ) ; +#4529 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51312, #68086, #13405, #82445 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4530 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#4531 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8099999999999852873 ) ) ; +#4532 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4533 = EDGE_CURVE ( 'NONE', #47306, #9173, #43532, .T. ) ; +#4534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61638 ), #33879 ) ; +#4535 = PRESENTATION_STYLE_ASSIGNMENT (( #91320 ) ) ; +#4536 = ORIENTED_EDGE ( 'NONE', *, *, #32609, .F. ) ; +#4537 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48601 ), #98977 ) ; +#4538 = VERTEX_POINT ( 'NONE', #36399 ) ; +#4539 = SURFACE_STYLE_FILL_AREA ( #44333 ) ; +#4540 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4541 = VECTOR ( 'NONE', #54015, 1000.000000000000114 ) ; +#4542 = FACE_OUTER_BOUND ( 'NONE', #76012, .T. ) ; +#4543 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#4544 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13174, 'distance_accuracy_value', 'NONE'); +#4545 = LINE ( 'NONE', #91332, #48589 ) ; +#4546 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #512, 'distance_accuracy_value', 'NONE'); +#4547 = CARTESIAN_POINT ( 'NONE', ( -1.293034295118453469, -0.9184269860678264674, 0.8100000000000483480 ) ) ; +#4548 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4549 = VERTEX_POINT ( 'NONE', #83362 ) ; +#4550 = ADVANCED_FACE ( 'NONE', ( #60409 ), #74699, .T. ) ; +#4551 = ORIENTED_EDGE ( 'NONE', *, *, #61972, .T. ) ; +#4552 = SURFACE_STYLE_FILL_AREA ( #43369 ) ; +#4553 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4554 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#4555 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95794 ) ) ; +#4556 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4557 = CARTESIAN_POINT ( 'NONE', ( -0.4535372177072710120, -0.9179759943635570352, 0.8299999999999999600 ) ) ; +#4558 = CARTESIAN_POINT ( 'NONE', ( -0.6534453840631663235, 1.365656627903983011, 0.8100000000000001643 ) ) ; +#4559 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4561 = ORIENTED_EDGE ( 'NONE', *, *, #61071, .T. ) ; +#4560 = EDGE_LOOP ( 'NONE', ( #29670, #12874, #82980, #70040 ) ) ; +#4562 = AXIS2_PLACEMENT_3D ( 'NONE', #62369, #36868, #30674 ) ; +#4563 = EDGE_LOOP ( 'NONE', ( #44748, #71880, #71936, #12681 ) ) ; +#4564 = AXIS2_PLACEMENT_3D ( 'NONE', #8349, #32441, #48281 ) ; +#4565 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58588 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32788, #93517, #1130 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4567 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#4566 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4568 = VERTEX_POINT ( 'NONE', #59413 ) ; +#4569 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4570 = ORIENTED_EDGE ( 'NONE', *, *, #6865, .T. ) ; +#4571 = ADVANCED_FACE ( 'NONE', ( #44518 ), #37452, .F. ) ; +#4572 = LINE ( 'NONE', #27095, #78983 ) ; +#4573 = LINE ( 'NONE', #35768, #100267 ) ; +#4574 = VERTEX_POINT ( 'NONE', #78697 ) ; +#4575 = ORIENTED_EDGE ( 'NONE', *, *, #47675, .F. ) ; +#4576 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#4577 = ORIENTED_EDGE ( 'NONE', *, *, #89273, .F. ) ; +#4578 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#4579 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#4580 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#4581 = EDGE_CURVE ( 'NONE', #52672, #37356, #62910, .T. ) ; +#4582 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64947 ), #58510 ) ; +#4583 = EDGE_CURVE ( 'NONE', #87907, #58354, #14355, .T. ) ; +#4584 = VECTOR ( 'NONE', #49471, 1000.000000000000000 ) ; +#4585 = ORIENTED_EDGE ( 'NONE', *, *, #68362, .T. ) ; +#4586 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73049 ) ) ; +#4587 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#4588 = VECTOR ( 'NONE', #33477, 1000.000000000000000 ) ; +#4589 = ORIENTED_EDGE ( 'NONE', *, *, #14315, .F. ) ; +#4590 = CARTESIAN_POINT ( 'NONE', ( -0.07142958428783030556, -1.223383224893549892, 0.8100000000000000533 ) ) ; +#4591 = CLOSED_SHELL ( 'NONE', ( #29223, #24636, #10305, #74375, #51237, #29833 ) ) ; +#4592 = VERTEX_POINT ( 'NONE', #71044 ) ; +#4593 = EDGE_LOOP ( 'NONE', ( #83923, #60997, #36021, #19931 ) ) ; +#4594 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 1.233333333333333393, 0.000000000000000000 ) ) ; +#4595 = LINE ( 'NONE', #3107, #93735 ) ; +#4596 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79550 ), #87778 ) ; +#4597 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#4598 = CARTESIAN_POINT ( 'NONE', ( -1.311685777689840293, -1.173235213159260049, 0.8300000000000000711 ) ) ; +#4599 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #63768, #24976, #56108, #17263, #48455, #79583, #40784, #85195, #61757, #92822, #22942, #15217, #25470, #11545, #27474 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 3.254691442281547933E-05, 6.496760486227517854E-05, 9.654590471381844694E-05, 0.0001268464953954521839, 0.0001414548951624552877, 0.0001556778735015829215, 0.0001697390785829380852, 0.0001834260504059259493, 0.0001969481326690250837, 0.0002103027335186611420, 0.0002239549281615506868, 0.0002379690393046756010 ), + .UNSPECIFIED. ) ; +#4600 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4601 = SURFACE_STYLE_USAGE ( .BOTH. , #50613 ) ; +#4603 = FILL_AREA_STYLE ('',( #35800 ) ) ; +#4602 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.383333333333333304, 0.000000000000000000 ) ) ; +#4604 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4605 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#4606 = ORIENTED_EDGE ( 'NONE', *, *, #30242, .F. ) ; +#4607 = SURFACE_SIDE_STYLE ('',( #81760 ) ) ; +#4608 = ADVANCED_FACE ( 'NONE', ( #8660 ), #580, .T. ) ; +#4609 = CARTESIAN_POINT ( 'NONE', ( -0.9123894243494741207, -1.359907766992060285, 0.8100000000000000533 ) ) ; +#4610 = ORIENTED_EDGE ( 'NONE', *, *, #21214, .F. ) ; +#4611 = SURFACE_SIDE_STYLE ('',( #49607 ) ) ; +#4612 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66570 ) ) ; +#4613 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#4614 = CARTESIAN_POINT ( 'NONE', ( -0.3666263778268459839, -1.099567016183110146, 0.8300000000000000711 ) ) ; +#4616 = FILL_AREA_STYLE ('',( #49110 ) ) ; +#4615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4617 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4618 = CARTESIAN_POINT ( 'NONE', ( 1.799634867437250207, -1.074567238704529970, 0.8299999999999999600 ) ) ; +#4619 = EDGE_CURVE ( 'NONE', #82578, #92379, #61896, .T. ) ; +#4620 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #9109, .NOT_KNOWN. ) ; +#4621 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#4622 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#4623 = SURFACE_SIDE_STYLE ('',( #76089 ) ) ; +#4624 = VECTOR ( 'NONE', #53576, 1000.000000000000000 ) ; +#4625 = EDGE_CURVE ( 'NONE', #29762, #22600, #30205, .T. ) ; +#4626 = ORIENTED_EDGE ( 'NONE', *, *, #2741, .T. ) ; +#4627 = AXIS2_PLACEMENT_3D ( 'NONE', #79888, #95656, #18045 ) ; +#4629 = SURFACE_STYLE_USAGE ( .BOTH. , #27658 ) ; +#4628 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4630 = LINE ( 'NONE', #20972, #75008 ) ; +#4631 = EDGE_CURVE ( 'NONE', #59283, #89393, #93201, .T. ) ; +#4632 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#4634 = EDGE_CURVE ( 'NONE', #15908, #30844, #53713, .T. ) ; +#4633 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66147, 'distance_accuracy_value', 'NONE'); +#4635 = EDGE_LOOP ( 'NONE', ( #68973, #40599, #80920, #70028 ) ) ; +#4636 = VECTOR ( 'NONE', #44213, 1000.000000000000000 ) ; +#4637 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4638 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, 0.000000000000000000 ) ) ; +#4639 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4640 = FACE_OUTER_BOUND ( 'NONE', #15844, .T. ) ; +#4641 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4642 = LINE ( 'NONE', #89429, #76884 ) ; +#4643 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4644 = EDGE_CURVE ( 'NONE', #49054, #82555, #79901, .T. ) ; +#4645 = ADVANCED_FACE ( 'NONE', ( #49599 ), #3116, .T. ) ; +#4646 = FILL_AREA_STYLE_COLOUR ( '', #77914 ) ; +#4647 = CIRCLE ( 'NONE', #12828, 0.09999999999999999167 ) ; +#4648 = AXIS2_PLACEMENT_3D ( 'NONE', #62449, #37458, #93526 ) ; +#4649 = ORIENTED_EDGE ( 'NONE', *, *, #72973, .T. ) ; +#4650 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4651 = ORIENTED_EDGE ( 'NONE', *, *, #93252, .T. ) ; +#4652 = VECTOR ( 'NONE', #31495, 1000.000000000000000 ) ; +#4653 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4654 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79555, 'distance_accuracy_value', 'NONE'); +#4655 = EDGE_CURVE ( 'NONE', #46513, #60060, #96514, .T. ) ; +#4656 = EDGE_CURVE ( 'NONE', #23798, #27455, #66494, .T. ) ; +#4657 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 6.999539000000000399, 0.8648700000000000276 ) ) ; +#4659 = AXIS2_PLACEMENT_3D ( 'NONE', #80051, #96816, #33060 ) ; +#4658 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#4660 = SURFACE_SIDE_STYLE ('',( #65965 ) ) ; +#4661 = CYLINDRICAL_SURFACE ( 'NONE', #57534, 0.1999999999999996503 ) ; +#4662 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4663 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, 0.000000000000000000 ) ) ; +#4664 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#4665 = VECTOR ( 'NONE', #8407, 1000.000000000000000 ) ; +#4666 = EDGE_LOOP ( 'NONE', ( #36645, #41913, #332, #72648 ) ) ; +#4667 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#4668 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.899999999999999911, 0.000000000000000000 ) ) ; +#4669 = SURFACE_SIDE_STYLE ('',( #36342 ) ) ; +#4670 = EDGE_LOOP ( 'NONE', ( #62792, #76302, #27149, #38534 ) ) ; +#4671 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#4672 = EDGE_CURVE ( 'NONE', #76926, #1018, #26119, .T. ) ; +#4673 = VERTEX_POINT ( 'NONE', #87368 ) ; +#4674 = STYLED_ITEM ( 'NONE', ( #39160 ), #50724 ) ; +#4675 = EDGE_CURVE ( 'NONE', #86575, #44133, #18414, .T. ) ; +#4676 = SURFACE_SIDE_STYLE ('',( #91952 ) ) ; +#4677 = VECTOR ( 'NONE', #62204, 1000.000000000000000 ) ; +#4678 = CARTESIAN_POINT ( 'NONE', ( 8.687142875125045904, 2.261923875125043892, 0.8648700000000000276 ) ) ; +#4679 = VECTOR ( 'NONE', #32884, 1000.000000000000000 ) ; +#4680 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.103411969279230082E-12, -5.103411969279230082E-12 ) ) ; +#4681 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4682 = ORIENTED_EDGE ( 'NONE', *, *, #18369, .T. ) ; +#4683 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#4684 = ORIENTED_EDGE ( 'NONE', *, *, #17579, .T. ) ; +#4685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4686 = CARTESIAN_POINT ( 'NONE', ( -1.633333333333333304, 3.500000000000000000, 0.000000000000000000 ) ) ; +#4687 = ORIENTED_EDGE ( 'NONE', *, *, #13796, .F. ) ; +#4688 = VERTEX_POINT ( 'NONE', #18922 ) ; +#4689 = SURFACE_STYLE_FILL_AREA ( #83828 ) ; +#4690 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#4691 = LINE ( 'NONE', #35879, #34284 ) ; +#4692 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#4693 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#4694 = PLANE ( 'NONE', #66596 ) ; +#4695 = STYLED_ITEM ( 'NONE', ( #86037 ), #32497 ) ; +#4696 = CARTESIAN_POINT ( 'NONE', ( 0.1681119866146557340, 0.5791465759208540565, 0.8299999999999999600 ) ) ; +#4697 = ORIENTED_EDGE ( 'NONE', *, *, #16160, .F. ) ; +#4698 = EDGE_LOOP ( 'NONE', ( #79806, #77690, #89766, #24471 ) ) ; +#4699 = ORIENTED_EDGE ( 'NONE', *, *, #41922, .F. ) ; +#4700 = FACE_OUTER_BOUND ( 'NONE', #73419, .T. ) ; +#4701 = VECTOR ( 'NONE', #92787, 1000.000000000000000 ) ; +#4702 = EDGE_CURVE ( 'NONE', #28967, #96609, #50119, .T. ) ; +#4703 = VECTOR ( 'NONE', #73674, 1000.000000000000000 ) ; +#4705 = ORIENTED_EDGE ( 'NONE', *, *, #66427, .T. ) ; +#4704 = PRESENTATION_STYLE_ASSIGNMENT (( #67000 ) ) ; +#4706 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4707 = AXIS2_PLACEMENT_3D ( 'NONE', #16066, #40092, #9364 ) ; +#4708 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#4709 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -2.143355994988570127E-63 ) ) ; +#4710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4711 = ORIENTED_EDGE ( 'NONE', *, *, #47662, .T. ) ; +#4713 = EDGE_CURVE ( 'NONE', #15411, #17884, #65918, .T. ) ; +#4712 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#4714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4715 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#4716 = EDGE_LOOP ( 'NONE', ( #6167, #35190, #2222, #25559, #61916, #24359, #87834, #83710, #71920, #32512 ) ) ; +#4717 = STYLED_ITEM ( 'NONE', ( #28547 ), #5926 ) ; +#4718 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#4719 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#4720 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#4721 = VECTOR ( 'NONE', #40321, 1000.000000000000000 ) ; +#4722 = FACE_OUTER_BOUND ( 'NONE', #67771, .T. ) ; +#4723 = FILL_AREA_STYLE ('',( #21552 ) ) ; +#4724 = CARTESIAN_POINT ( 'NONE', ( 1.817674829793840319, -1.368793146596559929, 0.8299999999999999600 ) ) ; +#4725 = FILL_AREA_STYLE ('',( #59911 ) ) ; +#4726 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#4727 = VECTOR ( 'NONE', #17214, 1000.000000000000114 ) ; +#4728 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, -3.500000000000000444, 0.000000000000000000 ) ) ; +#4729 = EDGE_CURVE ( 'NONE', #88972, #74680, #16893, .T. ) ; +#4730 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48800 ) ) ; +#4731 = ORIENTED_EDGE ( 'NONE', *, *, #30535, .F. ) ; +#4732 = SURFACE_SIDE_STYLE ('',( #51227 ) ) ; +#4733 = STYLED_ITEM ( 'NONE', ( #82926 ), #42210 ) ; +#4734 = FACE_OUTER_BOUND ( 'NONE', #95973, .T. ) ; +#4735 = AXIS2_PLACEMENT_3D ( 'NONE', #85342, #15376, #39386 ) ; +#4737 = SURFACE_SIDE_STYLE ('',( #89531 ) ) ; +#4736 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722699999999918, 0.8648700000000000276 ) ) ; +#4738 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#4740 = EDGE_CURVE ( 'NONE', #86972, #63874, #33264, .T. ) ; +#4739 = SURFACE_SIDE_STYLE ('',( #44533 ) ) ; +#4741 = SURFACE_STYLE_USAGE ( .BOTH. , #19050 ) ; +#4742 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4743 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#4744 = VERTEX_POINT ( 'NONE', #32758 ) ; +#4745 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4746 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#4747 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83185 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33961, #3301, #74751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4748 = SURFACE_STYLE_USAGE ( .BOTH. , #74718 ) ; +#4749 = ORIENTED_EDGE ( 'NONE', *, *, #86509, .F. ) ; +#4750 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#4752 = SURFACE_STYLE_USAGE ( .BOTH. , #4265 ) ; +#4751 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#4753 = PLANE ( 'NONE', #17837 ) ; +#4754 = ADVANCED_FACE ( 'NONE', ( #79740 ), #9685, .T. ) ; +#4755 = VECTOR ( 'NONE', #54558, 1000.000000000000000 ) ; +#4756 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#4757 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#4758 = FILL_AREA_STYLE_COLOUR ( '', #85266 ) ; +#4759 = ADVANCED_FACE ( 'NONE', ( #52109 ), #11681, .F. ) ; +#4760 = VERTEX_POINT ( 'NONE', #44400 ) ; +#4761 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#4762 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#4763 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#4764 = CARTESIAN_POINT ( 'NONE', ( 1.177393120509059976, -0.8847374564574109757, 0.8299999999999994049 ) ) ; +#4765 = CARTESIAN_POINT ( 'NONE', ( 1.089506002794699890, -1.495173285438690103, 0.8300000000000010703 ) ) ; +#4766 = SURFACE_STYLE_USAGE ( .BOTH. , #13886 ) ; +#4767 = AXIS2_PLACEMENT_3D ( 'NONE', #94565, #63959, #10226 ) ; +#4768 = VECTOR ( 'NONE', #53827, 1000.000000000000000 ) ; +#4769 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4770 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#4771 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4772 = VECTOR ( 'NONE', #19207, 1000.000000000000000 ) ; +#4773 = EDGE_LOOP ( 'NONE', ( #16372, #54196, #29335, #9517 ) ) ; +#4774 = ORIENTED_EDGE ( 'NONE', *, *, #63734, .F. ) ; +#4775 = SURFACE_SIDE_STYLE ('',( #97672 ) ) ; +#4776 = AXIS2_PLACEMENT_3D ( 'NONE', #20534, #19542, #27737 ) ; +#4777 = EDGE_CURVE ( 'NONE', #26954, #9775, #59295, .T. ) ; +#4778 = EDGE_CURVE ( 'NONE', #86804, #92223, #82246, .T. ) ; +#4779 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#4780 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#4781 = CYLINDRICAL_SURFACE ( 'NONE', #45986, 0.2000000000000000111 ) ; +#4782 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 12.65647100000000158, 0.8991599999999999593 ) ) ; +#4783 = CARTESIAN_POINT ( 'NONE', ( -0.7059659090909090606, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#4784 = FILL_AREA_STYLE ('',( #90062 ) ) ; +#4785 = ORIENTED_EDGE ( 'NONE', *, *, #30242, .T. ) ; +#4786 = VECTOR ( 'NONE', #75776, 1000.000000000000000 ) ; +#4787 = LINE ( 'NONE', #20612, #893 ) ; +#4788 = PLANE ( 'NONE', #40529 ) ; +#4789 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42282 ), #58630 ) ; +#4790 = FILL_AREA_STYLE ('',( #20110 ) ) ; +#4791 = EDGE_CURVE ( 'NONE', #76033, #97367, #74071, .T. ) ; +#4792 = AXIS2_PLACEMENT_3D ( 'NONE', #17050, #70682, #228 ) ; +#4793 = ORIENTED_EDGE ( 'NONE', *, *, #86591, .F. ) ; +#4794 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#4795 = EDGE_CURVE ( 'NONE', #90340, #38479, #97523, .T. ) ; +#4796 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#4797 = STYLED_ITEM ( 'NONE', ( #30581 ), #64040 ) ; +#4798 = SURFACE_STYLE_FILL_AREA ( #5271 ) ; +#4799 = SURFACE_STYLE_USAGE ( .BOTH. , #14433 ) ; +#4800 = VECTOR ( 'NONE', #59696, 1000.000000000000000 ) ; +#4801 = ORIENTED_EDGE ( 'NONE', *, *, #60314, .T. ) ; +#4802 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4803 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58649 ) ) ; +#4804 = FACE_OUTER_BOUND ( 'NONE', #90632, .T. ) ; +#4805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4806 = VECTOR ( 'NONE', #74465, 1000.000000000000000 ) ; +#4807 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#4808 = EDGE_LOOP ( 'NONE', ( #21545, #65047, #11631, #60872 ) ) ; +#4809 = PRESENTATION_STYLE_ASSIGNMENT (( #82452 ) ) ; +#4810 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 9.801187639268928344E-18, -0.8499999999999999778 ) ) ; +#4811 = CARTESIAN_POINT ( 'NONE', ( 2.033333333333326554, -3.500000000000000000, 0.000000000000000000 ) ) ; +#4812 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39088 ), #57059 ) ; +#4813 = EDGE_LOOP ( 'NONE', ( #87980, #26354, #73958, #16968 ) ) ; +#4814 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.600000000000000089, -11.41999999999999993 ) ) ; +#4815 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66838 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40992, #65440, #50172 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4816 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11236 ) ) ; +#4817 = ORIENTED_EDGE ( 'NONE', *, *, #78784, .F. ) ; +#4819 = VERTEX_POINT ( 'NONE', #27049 ) ; +#4818 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#4820 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67876, 'distance_accuracy_value', 'NONE'); +#4821 = LINE ( 'NONE', #27855, #23030 ) ; +#4823 = FILL_AREA_STYLE_COLOUR ( '', #8914 ) ; +#4822 = PRESENTATION_STYLE_ASSIGNMENT (( #74796 ) ) ; +#4824 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4825 = SURFACE_STYLE_USAGE ( .BOTH. , #81971 ) ; +#4827 = EDGE_CURVE ( 'NONE', #46653, #50031, #72996, .T. ) ; +#4826 = PLANE ( 'NONE', #87947 ) ; +#4828 = PRESENTATION_STYLE_ASSIGNMENT (( #37514 ) ) ; +#4829 = ORIENTED_EDGE ( 'NONE', *, *, #40541, .F. ) ; +#4830 = SURFACE_STYLE_USAGE ( .BOTH. , #20154 ) ; +#4831 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71692, #62547, #25263, #46672 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4832 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.000000000000000000 ) ) ; +#4833 = ORIENTED_EDGE ( 'NONE', *, *, #85946, .F. ) ; +#4834 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#4835 = ORIENTED_EDGE ( 'NONE', *, *, #27250, .T. ) ; +#4837 = PLANE ( 'NONE', #27027 ) ; +#4836 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4838 = SURFACE_STYLE_FILL_AREA ( #74812 ) ; +#4839 = LINE ( 'NONE', #36532, #3418 ) ; +#4840 = STYLED_ITEM ( 'NONE', ( #70007 ), #57240 ) ; +#4841 = PRESENTATION_STYLE_ASSIGNMENT (( #90122 ) ) ; +#4842 = VECTOR ( 'NONE', #65444, 1000.000000000000000 ) ; +#4843 = STYLED_ITEM ( 'NONE', ( #13842 ), #93957 ) ; +#4844 = FILL_AREA_STYLE ('',( #92972 ) ) ; +#4845 = VERTEX_POINT ( 'NONE', #72471 ) ; +#4846 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706229E-17, 0.6700000000000000400, -0.1999999999999999833 ) ) ; +#4847 = EDGE_LOOP ( 'NONE', ( #4216, #34865, #54741, #71348 ) ) ; +#4849 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#4848 = AXIS2_PLACEMENT_3D ( 'NONE', #59075, #92642, #39069 ) ; +#4851 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#4850 = FACE_OUTER_BOUND ( 'NONE', #84486, .T. ) ; +#4852 = SURFACE_STYLE_USAGE ( .BOTH. , #60033 ) ; +#4853 = EDGE_CURVE ( 'NONE', #74640, #11614, #39729, .T. ) ; +#4854 = VECTOR ( 'NONE', #82943, 1000.000000000000000 ) ; +#4855 = SURFACE_SIDE_STYLE ('',( #98227 ) ) ; +#4856 = LINE ( 'NONE', #14494, #53919 ) ; +#4858 = ADVANCED_FACE ( 'NONE', ( #40859 ), #50043, .T. ) ; +#4857 = FILL_AREA_STYLE ('',( #5334 ) ) ; +#4859 = CARTESIAN_POINT ( 'NONE', ( 2.123820061220085265, 3.099999999999969891, 0.000000000000000000 ) ) ; +#4860 = SURFACE_SIDE_STYLE ('',( #96274 ) ) ; +#4861 = ORIENTED_EDGE ( 'NONE', *, *, #10239, .F. ) ; +#4862 = VECTOR ( 'NONE', #53983, 1000.000000000000114 ) ; +#4863 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#4864 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4866 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#4865 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#4867 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12729, 'distance_accuracy_value', 'NONE'); +#4868 = PLANE ( 'NONE', #33816 ) ; +#4869 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#4870 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#4871 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4872 = EDGE_CURVE ( 'NONE', #39727, #50722, #57196, .T. ) ; +#4873 = ORIENTED_EDGE ( 'NONE', *, *, #44534, .T. ) ; +#4874 = SURFACE_STYLE_FILL_AREA ( #35572 ) ; +#4875 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000777, 0.1499999999999999944 ) ) ; +#4876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54027 ) ) ; +#4877 = FACE_OUTER_BOUND ( 'NONE', #67768, .T. ) ; +#4878 = FILL_AREA_STYLE ('',( #15014 ) ) ; +#4879 = VECTOR ( 'NONE', #46303, 1000.000000000000000 ) ; +#4880 = FILL_AREA_STYLE ('',( #27394 ) ) ; +#4881 = LINE ( 'NONE', #36070, #73947 ) ; +#4882 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48948 ), #81555 ) ; +#4883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4884 = SURFACE_STYLE_FILL_AREA ( #73861 ) ; +#4885 = FACE_OUTER_BOUND ( 'NONE', #11288, .T. ) ; +#4886 = FILL_AREA_STYLE ('',( #29399 ) ) ; +#4887 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63615 ), #91274 ) ; +#4888 = EDGE_CURVE ( 'NONE', #44836, #90311, #73504, .T. ) ; +#4889 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4890 = FILL_AREA_STYLE_COLOUR ( '', #84520 ) ; +#4891 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#4892 = FILL_AREA_STYLE_COLOUR ( '', #38578 ) ; +#4893 = CARTESIAN_POINT ( 'NONE', ( -0.9121606455498090238, -1.316410597191429943, 0.8100000000000000533 ) ) ; +#4894 = VERTEX_POINT ( 'NONE', #41855 ) ; +#4895 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4896 = SURFACE_SIDE_STYLE ('',( #51416 ) ) ; +#4897 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48967 ) ) ; +#4898 = FACE_OUTER_BOUND ( 'NONE', #61479, .T. ) ; +#4899 = PRESENTATION_STYLE_ASSIGNMENT (( #52412 ) ) ; +#4900 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61461, #68570, #78275, #86430 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#4901 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79938 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65138, #88133, #55498 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4902 = ADVANCED_FACE ( 'NONE', ( #95429 ), #49020, .T. ) ; +#4903 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28149 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33638, #88743, #52459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4904 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#4905 = ORIENTED_EDGE ( 'NONE', *, *, #65555, .F. ) ; +#4906 = LINE ( 'NONE', #67210, #16176 ) ; +#4907 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4908 = VERTEX_POINT ( 'NONE', #81682 ) ; +#4909 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#4910 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#4911 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4912 = STYLED_ITEM ( 'NONE', ( #66900 ), #94280 ) ; +#4913 = STYLED_ITEM ( 'NONE', ( #85268 ), #81559 ) ; +#4914 = VERTEX_POINT ( 'NONE', #17333 ) ; +#4915 = ORIENTED_EDGE ( 'NONE', *, *, #63134, .F. ) ; +#4916 = SURFACE_STYLE_USAGE ( .BOTH. , #59110 ) ; +#4917 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4918 = ORIENTED_EDGE ( 'NONE', *, *, #36842, .T. ) ; +#4919 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#4920 = PRESENTATION_STYLE_ASSIGNMENT (( #74906 ) ) ; +#4921 = LINE ( 'NONE', #60124, #93751 ) ; +#4922 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #40433, #1029 ) ; +#4923 = LINE ( 'NONE', #36124, #42738 ) ; +#4924 = AXIS2_PLACEMENT_3D ( 'NONE', #46678, #54378, #84002 ) ; +#4926 = VERTEX_POINT ( 'NONE', #21873 ) ; +#4925 = ORIENTED_EDGE ( 'NONE', *, *, #33815, .F. ) ; +#4927 = VERTEX_POINT ( 'NONE', #29537 ) ; +#4928 = VECTOR ( 'NONE', #26963, 1000.000000000000000 ) ; +#4929 = VECTOR ( 'NONE', #22601, 1000.000000000000000 ) ; +#4930 = ORIENTED_EDGE ( 'NONE', *, *, #31071, .T. ) ; +#4931 = SURFACE_STYLE_FILL_AREA ( #68225 ) ; +#4932 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#4933 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87781, 'distance_accuracy_value', 'NONE'); +#4934 = PLANE ( 'NONE', #1761 ) ; +#4935 = CARTESIAN_POINT ( 'NONE', ( 0.3979805126599459952, -0.9025088801136570416, 0.8100000000000000533 ) ) ; +#4936 = EDGE_CURVE ( 'NONE', #49745, #78286, #98395, .T. ) ; +#4937 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#4938 = PLANE ( 'NONE', #17978 ) ; +#4939 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4940 = ORIENTED_EDGE ( 'NONE', *, *, #52554, .T. ) ; +#4942 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#4941 = SURFACE_SIDE_STYLE ('',( #12560 ) ) ; +#4943 = ORIENTED_EDGE ( 'NONE', *, *, #95409, .T. ) ; +#4944 = VERTEX_POINT ( 'NONE', #91803 ) ; +#4945 = AXIS2_PLACEMENT_3D ( 'NONE', #54923, #63082, #16564 ) ; +#4946 = CARTESIAN_POINT ( 'NONE', ( 1.207735270546159922, -1.226800916006800080, 0.8299999999999999600 ) ) ; +#4948 = LINE ( 'NONE', #52972, #44972 ) ; +#4947 = SURFACE_STYLE_FILL_AREA ( #52971 ) ; +#4949 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#4951 = EDGE_LOOP ( 'NONE', ( #44732, #71125, #73289, #23652 ) ) ; +#4950 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34321 ), #39226 ) ; +#4952 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#4953 = ORIENTED_EDGE ( 'NONE', *, *, #99397, .F. ) ; +#4954 = LINE ( 'NONE', #52466, #25489 ) ; +#4955 = PLANE ( 'NONE', #58843 ) ; +#4956 = ORIENTED_EDGE ( 'NONE', *, *, #55871, .T. ) ; +#4957 = LINE ( 'NONE', #98337, #77524 ) ; +#4958 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, 0.000000000000000000 ) ) ; +#4959 = VERTEX_POINT ( 'NONE', #21369 ) ; +#4960 = ORIENTED_EDGE ( 'NONE', *, *, #55187, .F. ) ; +#4962 = PRESENTATION_STYLE_ASSIGNMENT (( #74954 ) ) ; +#4961 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4963 = PRESENTATION_STYLE_ASSIGNMENT (( #46269 ) ) ; +#4964 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4965 = STYLED_ITEM ( 'NONE', ( #25374 ), #18008 ) ; +#4966 = VECTOR ( 'NONE', #8357, 1000.000000000000114 ) ; +#4967 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#4968 = EDGE_CURVE ( 'NONE', #7486, #49779, #14163, .T. ) ; +#4969 = EDGE_CURVE ( 'NONE', #62932, #88860, #90308, .T. ) ; +#4970 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #91 ) ; +#4971 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#4972 = FILL_AREA_STYLE_COLOUR ( '', #61907 ) ; +#4973 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45694 ) ) ; +#4974 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6238, 'distance_accuracy_value', 'NONE'); +#4975 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18015 ), #71851 ) ; +#4976 = ORIENTED_EDGE ( 'NONE', *, *, #24542, .T. ) ; +#4977 = FACE_OUTER_BOUND ( 'NONE', #64373, .T. ) ; +#4978 = ORIENTED_EDGE ( 'NONE', *, *, #86451, .F. ) ; +#4979 = SURFACE_STYLE_FILL_AREA ( #28987 ) ; +#4980 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4981 = PLANE ( 'NONE', #67622 ) ; +#4982 = STYLED_ITEM ( 'NONE', ( #59923 ), #94727 ) ; +#4983 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#4985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#4984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17467 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1574, #2573, #33217 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#4986 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#4987 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#4988 = EDGE_CURVE ( 'NONE', #17982, #99540, #58707, .T. ) ; +#4989 = ORIENTED_EDGE ( 'NONE', *, *, #91807, .F. ) ; +#4990 = ADVANCED_FACE ( 'NONE', ( #89809 ), #98892, .T. ) ; +#4991 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#4992 = CARTESIAN_POINT ( 'NONE', ( 0.1707063580043630124, -1.088378544347549992, 0.8299999999999999600 ) ) ; +#4993 = DIRECTION ( 'NONE', ( -0.3376989467541748891, -0.9412541746845646262, 0.000000000000000000 ) ) ; +#4994 = SURFACE_STYLE_FILL_AREA ( #43320 ) ; +#4995 = FILL_AREA_STYLE ('',( #81659 ) ) ; +#4996 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#4997 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#4998 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#4999 = PLANE ( 'NONE', #77705 ) ; +#5000 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39220 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20083, #27786, #18050 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5001 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8991599999999999593 ) ) ; +#5002 = FACE_OUTER_BOUND ( 'NONE', #56501, .T. ) ; +#5003 = ORIENTED_EDGE ( 'NONE', *, *, #990, .F. ) ; +#5004 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, -0.6999999999999999556 ) ) ; +#5005 = FILL_AREA_STYLE_COLOUR ( '', #87802 ) ; +#5006 = CARTESIAN_POINT ( 'NONE', ( -0.9958243310031014150, -0.9354145126045168013, 0.8100000000000355804 ) ) ; +#5007 = VERTEX_POINT ( 'NONE', #52527 ) ; +#5008 = LINE ( 'NONE', #83158, #54399 ) ; +#5009 = SURFACE_SIDE_STYLE ('',( #99857 ) ) ; +#5010 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5011 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#5012 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5013 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5014 = STYLED_ITEM ( 'NONE', ( #9262 ), #10305 ) ; +#5015 = EDGE_CURVE ( 'NONE', #13406, #67641, #37224, .T. ) ; +#5016 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#5017 = VERTEX_POINT ( 'NONE', #83172 ) ; +#5018 = EDGE_CURVE ( 'NONE', #36610, #95595, #27552, .T. ) ; +#5019 = ORIENTED_EDGE ( 'NONE', *, *, #84114, .F. ) ; +#5020 = PRESENTATION_STYLE_ASSIGNMENT (( #21371 ) ) ; +#5021 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#5022 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5023 = SURFACE_STYLE_USAGE ( .BOTH. , #99867 ) ; +#5024 = PRESENTATION_STYLE_ASSIGNMENT (( #29542 ) ) ; +#5025 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#5026 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5027 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#5028 = FILL_AREA_STYLE_COLOUR ( '', #46855 ) ; +#5029 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998557, 0.1400000000000000133 ) ) ; +#5030 = ORIENTED_EDGE ( 'NONE', *, *, #50013, .T. ) ; +#5031 = ORIENTED_EDGE ( 'NONE', *, *, #65691, .F. ) ; +#5032 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55676 ) ) ; +#5033 = AXIS2_PLACEMENT_3D ( 'NONE', #11387, #33981, #26820 ) ; +#5034 = ORIENTED_EDGE ( 'NONE', *, *, #70038, .T. ) ; +#5035 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#5036 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#5037 = SURFACE_STYLE_FILL_AREA ( #88837 ) ; +#5038 = CARTESIAN_POINT ( 'NONE', ( -0.4247119971151859796, -0.9357370515645540010, 0.8100000000000000533 ) ) ; +#5039 = EDGE_CURVE ( 'NONE', #68530, #45824, #13638, .T. ) ; +#5040 = CARTESIAN_POINT ( 'NONE', ( -0.3270901269614894802, 1.202348391920492920, 0.8100000000000000533 ) ) ; +#5041 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5043 = ORIENTED_EDGE ( 'NONE', *, *, #83009, .T. ) ; +#5042 = ORIENTED_EDGE ( 'NONE', *, *, #18006, .T. ) ; +#5044 = VECTOR ( 'NONE', #24107, 1000.000000000000000 ) ; +#5045 = ORIENTED_EDGE ( 'NONE', *, *, #85111, .F. ) ; +#5046 = CARTESIAN_POINT ( 'NONE', ( 1.654345427547579739, -0.9032194100038879458, 0.8099999999999981659 ) ) ; +#5047 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96374 ) ) ; +#5048 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9089, 'distance_accuracy_value', 'NONE'); +#5049 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49814, 'distance_accuracy_value', 'NONE'); +#5050 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, 0.000000000000000000 ) ) ; +#5051 = ORIENTED_EDGE ( 'NONE', *, *, #47414, .F. ) ; +#5052 = ADVANCED_FACE ( 'NONE', ( #29038 ), #97918, .T. ) ; +#5053 = EDGE_LOOP ( 'NONE', ( #78315, #63230, #94551, #93567 ) ) ; +#5054 = AXIS2_PLACEMENT_3D ( 'NONE', #88597, #96236, #27332 ) ; +#5055 = LINE ( 'NONE', #51593, #23709 ) ; +#5056 = SURFACE_STYLE_FILL_AREA ( #35765 ) ; +#5059 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5058 = AXIS2_PLACEMENT_3D ( 'NONE', #79665, #47483, #49022 ) ; +#5057 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#5060 = STYLED_ITEM ( 'NONE', ( #86923 ), #65897 ) ; +#5061 = SURFACE_STYLE_USAGE ( .BOTH. , #21413 ) ; +#5062 = ORIENTED_EDGE ( 'NONE', *, *, #51973, .F. ) ; +#5063 = EDGE_CURVE ( 'NONE', #66746, #41748, #93784, .T. ) ; +#5064 = ORIENTED_EDGE ( 'NONE', *, *, #24340, .T. ) ; +#5065 = SURFACE_SIDE_STYLE ('',( #75063 ) ) ; +#5066 = ORIENTED_EDGE ( 'NONE', *, *, #52987, .T. ) ; +#5067 = PLANE ( 'NONE', #64016 ) ; +#5068 = LINE ( 'NONE', #18527, #11763 ) ; +#5069 = VECTOR ( 'NONE', #26945, 1000.000000000000000 ) ; +#5070 = EDGE_CURVE ( 'NONE', #60527, #15315, #77499, .T. ) ; +#5072 = ORIENTED_EDGE ( 'NONE', *, *, #19977, .F. ) ; +#5071 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 9.827965999999999980, 0.8648700000000000276 ) ) ; +#5073 = VERTEX_POINT ( 'NONE', #392 ) ; +#5074 = CARTESIAN_POINT ( 'NONE', ( 0.001293116504768550062, -1.273483528256009967, 0.8100000000000000533 ) ) ; +#5075 = EDGE_LOOP ( 'NONE', ( #83232, #38999, #3003, #45542 ) ) ; +#5076 = ORIENTED_EDGE ( 'NONE', *, *, #35924, .F. ) ; +#5077 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5078 = PLANE ( 'NONE', #74189 ) ; +#5079 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5080 = SURFACE_STYLE_USAGE ( .BOTH. , #28115 ) ; +#5082 = EDGE_CURVE ( 'NONE', #37995, #59404, #63228, .T. ) ; +#5081 = SURFACE_STYLE_FILL_AREA ( #65914 ) ; +#5083 = EDGE_CURVE ( 'NONE', #50603, #30792, #54554, .T. ) ; +#5084 = PLANE ( 'NONE', #93233 ) ; +#5085 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5086 = PRESENTATION_STYLE_ASSIGNMENT (( #90897 ) ) ; +#5087 = LINE ( 'NONE', #57784, #99581 ) ; +#5088 = VERTEX_POINT ( 'NONE', #23916 ) ; +#5089 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5090 = CARTESIAN_POINT ( 'NONE', ( -0.9882503141469709540, -1.475119686261340046, 0.8100000000000000533 ) ) ; +#5091 = ORIENTED_EDGE ( 'NONE', *, *, #89187, .F. ) ; +#5092 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18134 ) ) ; +#5093 = SURFACE_STYLE_USAGE ( .BOTH. , #5585 ) ; +#5094 = CARTESIAN_POINT ( 'NONE', ( -0.1344673260136140247, -1.507258815139120189, 0.8100000000000000533 ) ) ; +#5095 = SURFACE_SIDE_STYLE ('',( #44410 ) ) ; +#5096 = LINE ( 'NONE', #52122, #71374 ) ; +#5097 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #91000, #75193, #43522, #37402 ), + .UNSPECIFIED., .F., .F. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#5098 = FILL_AREA_STYLE ('',( #67408 ) ) ; +#5099 = FILL_AREA_STYLE ('',( #60299 ) ) ; +#5100 = CARTESIAN_POINT ( 'NONE', ( 1.693812380665640216, -1.164588072778879990, 0.8299999999999999600 ) ) ; +#5101 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5102 = ADVANCED_FACE ( 'NONE', ( #38702 ), #70336, .T. ) ; +#5103 = EDGE_CURVE ( 'NONE', #15347, #94573, #909, .T. ) ; +#5104 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5105 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52396 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47509, #61363, #84309 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5106 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5107 = PRESENTATION_STYLE_ASSIGNMENT (( #91413 ) ) ; +#5108 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72832, #42706, #58850, #19495 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#5109 = FACE_OUTER_BOUND ( 'NONE', #3252, .T. ) ; +#5110 = DIRECTION ( 'NONE', ( 0.7071067811865482389, -0.7071067811865469066, 0.000000000000000000 ) ) ; +#5111 = LINE ( 'NONE', #75594, #75228 ) ; +#5112 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5113 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39151, #24373, #30988 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5114 = EDGE_CURVE ( 'NONE', #28098, #29915, #8474, .T. ) ; +#5115 = VERTEX_POINT ( 'NONE', #86681 ) ; +#5116 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#5117 = EDGE_CURVE ( 'NONE', #42167, #25468, #99863, .T. ) ; +#5118 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5119 = FILL_AREA_STYLE ('',( #66442 ) ) ; +#5120 = FILL_AREA_STYLE_COLOUR ( '', #4253 ) ; +#5121 = STYLED_ITEM ( 'NONE', ( #80672 ), #66216 ) ; +#5122 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5123 = CARTESIAN_POINT ( 'NONE', ( 0.01569390708528280165, 1.386225820966699995, 0.8100000000000000533 ) ) ; +#5124 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#5125 = ADVANCED_FACE ( 'NONE', ( #54030 ), #38208, .T. ) ; +#5126 = CARTESIAN_POINT ( 'NONE', ( 0.9366369866146579959, 0.4412590759269650054, 0.8299999999999999600 ) ) ; +#5127 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20394 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67221, #83063, #4917 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5128 = ORIENTED_EDGE ( 'NONE', *, *, #89614, .T. ) ; +#5129 = FILL_AREA_STYLE ('',( #75614 ) ) ; +#5130 = EDGE_CURVE ( 'NONE', #53045, #23560, #79028, .T. ) ; +#5131 = VERTEX_POINT ( 'NONE', #34598 ) ; +#5133 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13732, 'distance_accuracy_value', 'NONE'); +#5132 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8360 ) ) ; +#5134 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94553, 'distance_accuracy_value', 'NONE'); +#5135 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#5136 = CARTESIAN_POINT ( 'NONE', ( -0.1181104512869620010, -0.9624218420162741205, 0.8100000000000000533 ) ) ; +#5137 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, -0.8000000000000001554 ) ) ; +#5138 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5139 = SURFACE_STYLE_FILL_AREA ( #83305 ) ; +#5140 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77110 ), #82026 ) ; +#5141 = VERTEX_POINT ( 'NONE', #87687 ) ; +#5142 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5143 = FILL_AREA_STYLE ('',( #60841 ) ) ; +#5144 = ORIENTED_EDGE ( 'NONE', *, *, #23314, .F. ) ; +#5145 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5146 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5147 = ORIENTED_EDGE ( 'NONE', *, *, #22913, .T. ) ; +#5148 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73640 ), #98044 ) ; +#5149 = SURFACE_STYLE_FILL_AREA ( #99020 ) ; +#5150 = FACE_OUTER_BOUND ( 'NONE', #33374, .T. ) ; +#5151 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5152 = EDGE_CURVE ( 'NONE', #27714, #12287, #17219, .T. ) ; +#5153 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5154 = VERTEX_POINT ( 'NONE', #88205 ) ; +#5155 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3542 ) ) ; +#5156 = CARTESIAN_POINT ( 'NONE', ( 1.157511986614659927, 1.258646575926970268, 0.8299999999999999600 ) ) ; +#5157 = SURFACE_STYLE_USAGE ( .BOTH. , #59375 ) ; +#5158 = ORIENTED_EDGE ( 'NONE', *, *, #35494, .T. ) ; +#5159 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#5160 = FILL_AREA_STYLE_COLOUR ( '', #22839 ) ; +#5161 = ORIENTED_EDGE ( 'NONE', *, *, #13969, .T. ) ; +#5162 = EDGE_CURVE ( 'NONE', #4125, #65336, #96822, .T. ) ; +#5163 = ORIENTED_EDGE ( 'NONE', *, *, #76467, .F. ) ; +#5164 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.000000000000000000 ) ) ; +#5165 = AXIS2_PLACEMENT_3D ( 'NONE', #16716, #32594, #1449 ) ; +#5166 = FILL_AREA_STYLE ('',( #67965 ) ) ; +#5167 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#5168 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5169 = VERTEX_POINT ( 'NONE', #48417 ) ; +#5170 = EDGE_CURVE ( 'NONE', #23470, #41763, #18206, .T. ) ; +#5171 = ORIENTED_EDGE ( 'NONE', *, *, #40544, .F. ) ; +#5172 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100970 ) ; +#5173 = ORIENTED_EDGE ( 'NONE', *, *, #28200, .T. ) ; +#5174 = AXIS2_PLACEMENT_3D ( 'NONE', #36042, #26876, #74327 ) ; +#5175 = VECTOR ( 'NONE', #34707, 1000.000000000000000 ) ; +#5176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60701 ), #88384 ) ; +#5177 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #29294, #23337 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #38120 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#5178 = EDGE_CURVE ( 'NONE', #13162, #53594, #49396, .T. ) ; +#5179 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19137 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19134, #11407, #95719 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5180 = ORIENTED_EDGE ( 'NONE', *, *, #97780, .F. ) ; +#5181 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5182 = VERTEX_POINT ( 'NONE', #56062 ) ; +#5183 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5184 = DIRECTION ( 'NONE', ( 1.668003342285390072E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5185 = SURFACE_STYLE_USAGE ( .BOTH. , #52706 ) ; +#5186 = ORIENTED_EDGE ( 'NONE', *, *, #46545, .F. ) ; +#5187 = FILL_AREA_STYLE_COLOUR ( '', #25333 ) ; +#5188 = CARTESIAN_POINT ( 'NONE', ( 0.5268964082245309877, -1.158245412001609909, 0.8299999999999999600 ) ) ; +#5189 = VECTOR ( 'NONE', #78015, 1000.000000000000000 ) ; +#5190 = SURFACE_SIDE_STYLE ('',( #51722 ) ) ; +#5192 = EDGE_CURVE ( 'NONE', #11295, #39861, #80552, .T. ) ; +#5191 = FILL_AREA_STYLE ('',( #35419 ) ) ; +#5193 = EDGE_CURVE ( 'NONE', #53502, #15191, #72877, .T. ) ; +#5194 = CARTESIAN_POINT ( 'NONE', ( 1.743271607193970008, -1.437850337629750008, 0.8299999999999999600 ) ) ; +#5196 = PRESENTATION_STYLE_ASSIGNMENT (( #37416 ) ) ; +#5195 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041100000000085, 0.8648700000000000276 ) ) ; +#5197 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 15.09753200000000106, 0.8648700000000000276 ) ) ; +#5198 = VERTEX_POINT ( 'NONE', #65208 ) ; +#5199 = PLANE ( 'NONE', #14158 ) ; +#5200 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5201 = CARTESIAN_POINT ( 'NONE', ( 1.367767600758680091, -1.205184960463220323, 0.8300000000000022915 ) ) ; +#5202 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36249 ) ) ; +#5203 = CARTESIAN_POINT ( 'NONE', ( 1.585655134885600059, -1.389169665048220148, 0.8299999999999999600 ) ) ; +#5204 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999689, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#5205 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5206 = ADVANCED_FACE ( 'NONE', ( #81061 ), #94813, .T. ) ; +#5207 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28093 ) ) ; +#5208 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#5209 = ORIENTED_EDGE ( 'NONE', *, *, #6215, .T. ) ; +#5210 = VECTOR ( 'NONE', #90992, 1000.000000000000000 ) ; +#5211 = LINE ( 'NONE', #6681, #15264 ) ; +#5212 = FACE_OUTER_BOUND ( 'NONE', #76283, .T. ) ; +#5213 = ORIENTED_EDGE ( 'NONE', *, *, #92005, .T. ) ; +#5214 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#5216 = FILL_AREA_STYLE ('',( #5723 ) ) ; +#5215 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49300 ) ) ; +#5217 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.6600000000000000311, 0.8000000000000002665 ) ) ; +#5218 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#5219 = SURFACE_SIDE_STYLE ('',( #89548 ) ) ; +#5220 = AXIS2_PLACEMENT_3D ( 'NONE', #33435, #74732, #34446 ) ; +#5221 = SURFACE_STYLE_FILL_AREA ( #43067 ) ; +#5222 = ORIENTED_EDGE ( 'NONE', *, *, #97293, .F. ) ; +#5223 = LINE ( 'NONE', #28270, #6493 ) ; +#5224 = PRESENTATION_STYLE_ASSIGNMENT (( #20584 ) ) ; +#5225 = PRESENTATION_STYLE_ASSIGNMENT (( #75239 ) ) ; +#5226 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5227 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5228 = LINE ( 'NONE', #77219, #69786 ) ; +#5229 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5230 = LINE ( 'NONE', #29750, #19161 ) ; +#5231 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#5232 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5233 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5234 = SURFACE_SIDE_STYLE ('',( #44563 ) ) ; +#5235 = AXIS2_PLACEMENT_3D ( 'NONE', #64921, #597, #23596 ) ; +#5236 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24170, 'distance_accuracy_value', 'NONE'); +#5237 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20976 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37959, #7715, #85915 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5238 = FILL_AREA_STYLE ('',( #73736 ) ) ; +#5239 = FILL_AREA_STYLE_COLOUR ( '', #34073 ) ; +#5240 = ORIENTED_EDGE ( 'NONE', *, *, #14598, .T. ) ; +#5241 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#5242 = EDGE_CURVE ( 'NONE', #23326, #96537, #36025, .T. ) ; +#5244 = VERTEX_POINT ( 'NONE', #66703 ) ; +#5243 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77002 ), #32995 ) ; +#5245 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57021, 'distance_accuracy_value', 'NONE'); +#5246 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80290, 'distance_accuracy_value', 'NONE'); +#5247 = VECTOR ( 'NONE', #37309, 1000.000000000000000 ) ; +#5248 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#5249 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.5033332678760626955, 0.6832601346939835008 ) ) ; +#5250 = FACE_OUTER_BOUND ( 'NONE', #81207, .T. ) ; +#5251 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.78243800000000086, 0.8648700000000000276 ) ) ; +#5252 = SURFACE_STYLE_FILL_AREA ( #12377 ) ; +#5253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5254 = FACE_OUTER_BOUND ( 'NONE', #60508, .T. ) ; +#5256 = ADVANCED_FACE ( 'NONE', ( #83551 ), #83047, .F. ) ; +#5255 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5257 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#5258 = ORIENTED_EDGE ( 'NONE', *, *, #24241, .T. ) ; +#5259 = AXIS2_PLACEMENT_3D ( 'NONE', #66773, #97869, #18280 ) ; +#5260 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#5261 = FACE_OUTER_BOUND ( 'NONE', #38153, .T. ) ; +#5262 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99211, 'distance_accuracy_value', 'NONE'); +#5263 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5264 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15087 ), #410 ) ; +#5265 = VERTEX_POINT ( 'NONE', #75375 ) ; +#5266 = SURFACE_STYLE_USAGE ( .BOTH. , #75268 ) ; +#5267 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5268 = LINE ( 'NONE', #74266, #96741 ) ; +#5269 = VECTOR ( 'NONE', #68930, 1000.000000000000000 ) ; +#5270 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8648700000000000276 ) ) ; +#5271 = FILL_AREA_STYLE ('',( #74771 ) ) ; +#5272 = EDGE_CURVE ( 'NONE', #36125, #51917, #19757, .T. ) ; +#5273 = FILL_AREA_STYLE ('',( #29306 ) ) ; +#5274 = VERTEX_POINT ( 'NONE', #43720 ) ; +#5275 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#5276 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#5277 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16163, 'distance_accuracy_value', 'NONE'); +#5278 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5279 = CARTESIAN_POINT ( 'NONE', ( 1.596805013731110057, -1.020192282374009940, 0.8099999999999994982 ) ) ; +#5280 = EDGE_CURVE ( 'NONE', #33782, #92443, #43228, .T. ) ; +#5281 = VERTEX_POINT ( 'NONE', #4904 ) ; +#5282 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.09999999999999881206, 0.1829999999999749605 ) ) ; +#5284 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5283 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5285 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.500000000000000444, 0.000000000000000000 ) ) ; +#5286 = SURFACE_STYLE_FILL_AREA ( #91101 ) ; +#5287 = ORIENTED_EDGE ( 'NONE', *, *, #88382, .F. ) ; +#5288 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19975 ), #96557 ) ; +#5289 = AXIS2_PLACEMENT_3D ( 'NONE', #12446, #90645, #73331 ) ; +#5290 = ADVANCED_FACE ( 'NONE', ( #36101 ), #21249, .T. ) ; +#5291 = VERTEX_POINT ( 'NONE', #25194 ) ; +#5293 = VERTEX_POINT ( 'NONE', #61593 ) ; +#5292 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#5294 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#5295 = CARTESIAN_POINT ( 'NONE', ( -1.195496432507400009, -1.512608977738969962, 0.8299999999999999600 ) ) ; +#5296 = VECTOR ( 'NONE', #54664, 1000.000000000000000 ) ; +#5297 = SURFACE_STYLE_USAGE ( .BOTH. , #30300 ) ; +#5298 = VERTEX_POINT ( 'NONE', #95069 ) ; +#5300 = EDGE_CURVE ( 'NONE', #60423, #91206, #70214, .T. ) ; +#5299 = FILL_AREA_STYLE ('',( #91605 ) ) ; +#5301 = LINE ( 'NONE', #59529, #23891 ) ; +#5302 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#5303 = ORIENTED_EDGE ( 'NONE', *, *, #88349, .F. ) ; +#5304 = CARTESIAN_POINT ( 'NONE', ( 1.347634412165590101, -1.485054850390570058, 0.8100000000000000533 ) ) ; +#5305 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5306 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33055 ), #88515 ) ; +#5307 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75466 ) ) ; +#5308 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49388 ) ) ; +#5309 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5310 = EDGE_LOOP ( 'NONE', ( #12562, #41178, #66463, #75887 ) ) ; +#5311 = CARTESIAN_POINT ( 'NONE', ( 1.780058980618379971, -1.124571705400470023, 0.8100000000000008304 ) ) ; +#5312 = VERTEX_POINT ( 'NONE', #100245 ) ; +#5313 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77136 ) ) ; +#5314 = EDGE_CURVE ( 'NONE', #8781, #42470, #24998, .T. ) ; +#5315 = EDGE_CURVE ( 'NONE', #11144, #46450, #87440, .T. ) ; +#5316 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26597 ), #20006 ) ; +#5317 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 4.963071000000000232, 0.8648700000000000276 ) ) ; +#5318 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33071 ) ) ; +#5319 = ADVANCED_FACE ( 'NONE', ( #54432 ), #64471, .T. ) ; +#5320 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5321 = EDGE_CURVE ( 'NONE', #34323, #73258, #100423, .T. ) ; +#5322 = LINE ( 'NONE', #79, #99504 ) ; +#5323 = ORIENTED_EDGE ( 'NONE', *, *, #44980, .F. ) ; +#5324 = CARTESIAN_POINT ( 'NONE', ( 1.220343482084889963, -1.445215125000139933, 0.8299999999999999600 ) ) ; +#5325 = EDGE_LOOP ( 'NONE', ( #58619, #42760, #58045, #52985, #74195, #64933 ) ) ; +#5326 = CYLINDRICAL_SURFACE ( 'NONE', #86161, 0.05000000000000012768 ) ; +#5328 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5327 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5329 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5330 = EDGE_CURVE ( 'NONE', #74915, #27714, #45696, .T. ) ; +#5331 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5332 = LINE ( 'NONE', #82003, #29619 ) ; +#5333 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#5334 = FILL_AREA_STYLE_COLOUR ( '', #43032 ) ; +#5335 = SURFACE_STYLE_USAGE ( .BOTH. , #61540 ) ; +#5336 = FACE_OUTER_BOUND ( 'NONE', #56728, .T. ) ; +#5337 = EDGE_CURVE ( 'NONE', #51759, #96999, #95641, .T. ) ; +#5338 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5340 = ORIENTED_EDGE ( 'NONE', *, *, #83056, .T. ) ; +#5341 = LINE ( 'NONE', #67642, #18745 ) ; +#5342 = PRESENTATION_STYLE_ASSIGNMENT (( #59567 ) ) ; +#5343 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49421 ), #47808 ) ; +#5345 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5344 = SURFACE_STYLE_USAGE ( .BOTH. , #83504 ) ; +#5346 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#5347 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#5348 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5349 = VECTOR ( 'NONE', #17347, 1000.000000000000114 ) ; +#5350 = FILL_AREA_STYLE_COLOUR ( '', #40259 ) ; +#5351 = SURFACE_SIDE_STYLE ('',( #89668 ) ) ; +#5352 = ORIENTED_EDGE ( 'NONE', *, *, #8969, .T. ) ; +#5353 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5354 = LINE ( 'NONE', #37564, #68493 ) ; +#5355 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#5356 = AXIS2_PLACEMENT_3D ( 'NONE', #92134, #83997, #61543 ) ; +#5357 = SURFACE_STYLE_USAGE ( .BOTH. , #42703 ) ; +#5358 = FACE_OUTER_BOUND ( 'NONE', #97889, .T. ) ; +#5359 = LINE ( 'NONE', #28390, #6533 ) ; +#5360 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#5361 = LINE ( 'NONE', #75348, #87603 ) ; +#5362 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10182 ), #96634 ) ; +#5363 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#5364 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5365 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5366 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5367 = PLANE ( 'NONE', #30873 ) ; +#5368 = SURFACE_STYLE_FILL_AREA ( #4886 ) ; +#5369 = VECTOR ( 'NONE', #68132, 1000.000000000000000 ) ; +#5370 = CARTESIAN_POINT ( 'NONE', ( 10.92867087512504298, 5.422690875125044663, 0.8991599999999999593 ) ) ; +#5371 = EDGE_CURVE ( 'NONE', #64015, #75429, #52920, .T. ) ; +#5372 = LINE ( 'NONE', #14026, #79998 ) ; +#5373 = FACE_OUTER_BOUND ( 'NONE', #72294, .T. ) ; +#5374 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94463, 'distance_accuracy_value', 'NONE'); +#5375 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.033333333333333659, 0.000000000000000000 ) ) ; +#5376 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#5377 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5378 = DIRECTION ( 'NONE', ( -0.3438200982495985825, 0.000000000000000000, 0.9390355371548172458 ) ) ; +#5379 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5380 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67363 ), #99899 ) ; +#5381 = FILL_AREA_STYLE ('',( #37089 ) ) ; +#5382 = ORIENTED_EDGE ( 'NONE', *, *, #53315, .F. ) ; +#5383 = FILL_AREA_STYLE ('',( #91677 ) ) ; +#5384 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5385 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28735, 'distance_accuracy_value', 'NONE'); +#5386 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24504 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71919, #87732, #2473 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5388 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18291, 'distance_accuracy_value', 'NONE'); +#5389 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5390 = CARTESIAN_POINT ( 'NONE', ( -0.01509916179266439923, -1.018845982455530041, 0.8300000000000002931 ) ) ; +#5391 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20145 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5576, #20944, #97007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5392 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51149 ), #21747 ) ; +#5393 = VECTOR ( 'NONE', #58721, 1000.000000000000000 ) ; +#5394 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#5395 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8199999999999999512 ) ) ; +#5396 = ORIENTED_EDGE ( 'NONE', *, *, #69181, .F. ) ; +#5397 = STYLED_ITEM ( 'NONE', ( #57130 ), #59769 ) ; +#5398 = ORIENTED_EDGE ( 'NONE', *, *, #11902, .F. ) ; +#5399 = FILL_AREA_STYLE ('',( #20243 ) ) ; +#5400 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65270, 'distance_accuracy_value', 'NONE'); +#5401 = SURFACE_STYLE_FILL_AREA ( #75383 ) ; +#5402 = SURFACE_SIDE_STYLE ('',( #13527 ) ) ; +#5403 = PRESENTATION_STYLE_ASSIGNMENT (( #45213 ) ) ; +#5404 = ADVANCED_FACE ( 'NONE', ( #2190 ), #84050, .F. ) ; +#5405 = ORIENTED_EDGE ( 'NONE', *, *, #90416, .F. ) ; +#5406 = ORIENTED_EDGE ( 'NONE', *, *, #71214, .F. ) ; +#5407 = PRESENTATION_STYLE_ASSIGNMENT (( #4916 ) ) ; +#5408 = VERTEX_POINT ( 'NONE', #37600 ) ; +#5409 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#5410 = PRESENTATION_STYLE_ASSIGNMENT (( #58611 ) ) ; +#5411 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.700000000000000622, 0.1829999999999460114 ) ) ; +#5412 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#5413 = PRESENTATION_STYLE_ASSIGNMENT (( #38118 ) ) ; +#5414 = FILL_AREA_STYLE_COLOUR ( '', #50926 ) ; +#5416 = VERTEX_POINT ( 'NONE', #68697 ) ; +#5415 = ORIENTED_EDGE ( 'NONE', *, *, #45639, .F. ) ; +#5417 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37217 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54996, #69224, #62158 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5418 = VERTEX_POINT ( 'NONE', #92189 ) ; +#5419 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8648700000000000276 ) ) ; +#5420 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 5.422691000000000372, 0.8648700000000000276 ) ) ; +#5421 = CARTESIAN_POINT ( 'NONE', ( 1.302823766419570317, -0.9018902076549569768, 0.8299999999999999600 ) ) ; +#5422 = STYLED_ITEM ( 'NONE', ( #73285 ), #53178 ) ; +#5423 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#5424 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5425 = STYLED_ITEM ( 'NONE', ( #42572 ), #88247 ) ; +#5426 = ORIENTED_EDGE ( 'NONE', *, *, #67500, .F. ) ; +#5427 = FILL_AREA_STYLE ('',( #58135 ) ) ; +#5428 = VERTEX_POINT ( 'NONE', #22258 ) ; +#5429 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5430 = ORIENTED_EDGE ( 'NONE', *, *, #15213, .F. ) ; +#5431 = CARTESIAN_POINT ( 'NONE', ( 1.055638970329410009, -1.181386160465649926, 0.8299999999999999600 ) ) ; +#5432 = PRESENTATION_STYLE_ASSIGNMENT (( #26975 ) ) ; +#5434 = ORIENTED_EDGE ( 'NONE', *, *, #49414, .F. ) ; +#5433 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5435 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5436 = FILL_AREA_STYLE ('',( #14102 ) ) ; +#5437 = ORIENTED_EDGE ( 'NONE', *, *, #51123, .F. ) ; +#5438 = LINE ( 'NONE', #68255, #30420 ) ; +#5439 = EDGE_LOOP ( 'NONE', ( #98429, #28533, #3885, #47248 ) ) ; +#5440 = ORIENTED_EDGE ( 'NONE', *, *, #8425, .T. ) ; +#5441 = VECTOR ( 'NONE', #57558, 1000.000000000000000 ) ; +#5442 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#5443 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5444 = LINE ( 'NONE', #36666, #38375 ) ; +#5446 = VECTOR ( 'NONE', #100692, 1000.000000000000000 ) ; +#5445 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26733 ) ) ; +#5447 = AXIS2_PLACEMENT_3D ( 'NONE', #95399, #34183, #17806 ) ; +#5448 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5449 = FACE_OUTER_BOUND ( 'NONE', #12717, .T. ) ; +#5450 = FILL_AREA_STYLE ('',( #35673 ) ) ; +#5451 = STYLED_ITEM ( 'NONE', ( #13587 ), #60804 ) ; +#5452 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#5453 = VECTOR ( 'NONE', #66359, 1000.000000000000000 ) ; +#5454 = FILL_AREA_STYLE_COLOUR ( '', #47722 ) ; +#5455 = ADVANCED_FACE ( 'NONE', ( #53405 ), #76887, .T. ) ; +#5456 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5457 = VERTEX_POINT ( 'NONE', #33844 ) ; +#5458 = CARTESIAN_POINT ( 'NONE', ( 7.895183000000000284, 10.29465700000000083, 0.8648700000000000276 ) ) ; +#5459 = ORIENTED_EDGE ( 'NONE', *, *, #26355, .F. ) ; +#5460 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.000000000000000000 ) ) ; +#5461 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5462 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#5463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5464 = AXIS2_PLACEMENT_3D ( 'NONE', #8909, #57010, #40160 ) ; +#5465 = SURFACE_SIDE_STYLE ('',( #37676 ) ) ; +#5466 = FACE_OUTER_BOUND ( 'NONE', #79582, .T. ) ; +#5467 = LINE ( 'NONE', #43314, #87475 ) ; +#5468 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5469 = ORIENTED_EDGE ( 'NONE', *, *, #61948, .T. ) ; +#5470 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5471 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5472 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5473 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5474 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5475 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64275 ) ) ; +#5476 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5477 = VECTOR ( 'NONE', #25752, 1000.000000000000000 ) ; +#5478 = CARTESIAN_POINT ( 'NONE', ( 1.867699582579569917, -1.228633653069070020, 0.8100000000000000533 ) ) ; +#5479 = EDGE_CURVE ( 'NONE', #87432, #10501, #17971, .T. ) ; +#5480 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5481 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5482 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#5483 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#5484 = STYLED_ITEM ( 'NONE', ( #76070 ), #71256 ) ; +#5485 = FACE_OUTER_BOUND ( 'NONE', #43346, .T. ) ; +#5486 = FACE_OUTER_BOUND ( 'NONE', #81490, .T. ) ; +#5487 = AXIS2_PLACEMENT_3D ( 'NONE', #30797, #93051, #46617 ) ; +#5488 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23926, 'distance_accuracy_value', 'NONE'); +#5489 = ORIENTED_EDGE ( 'NONE', *, *, #57891, .F. ) ; +#5490 = CARTESIAN_POINT ( 'NONE', ( -0.08224541047086528223, -1.507148417626396286, 0.8099999999994883515 ) ) ; +#5492 = ADVANCED_FACE ( 'NONE', ( #20000 ), #35368, .T. ) ; +#5491 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.300000000000000044, 0.000000000000000000 ) ) ; +#5493 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5494 = ORIENTED_EDGE ( 'NONE', *, *, #49405, .F. ) ; +#5495 = SURFACE_STYLE_FILL_AREA ( #15684 ) ; +#5496 = LINE ( 'NONE', #36704, #95809 ) ; +#5497 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5498 = FILL_AREA_STYLE ('',( #13628 ) ) ; +#5500 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5499 = AXIS2_PLACEMENT_3D ( 'NONE', #59927, #29250, #5718 ) ; +#5501 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23157, 'distance_accuracy_value', 'NONE'); +#5502 = FILL_AREA_STYLE_COLOUR ( '', #89994 ) ; +#5504 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40087 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78753, #45547, #14912 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5503 = CARTESIAN_POINT ( 'NONE', ( 1.434211947550723121, -1.282982640083636383, 0.8099999999998119815 ) ) ; +#5505 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5506 = VECTOR ( 'NONE', #75328, 1000.000000000000000 ) ; +#5507 = ORIENTED_EDGE ( 'NONE', *, *, #39360, .T. ) ; +#5508 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, -3.149999999999979927, 0.000000000000000000 ) ) ; +#5509 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#5510 = SURFACE_STYLE_USAGE ( .BOTH. , #75501 ) ; +#5511 = PRESENTATION_STYLE_ASSIGNMENT (( #20877 ) ) ; +#5512 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36369, 'distance_accuracy_value', 'NONE'); +#5513 = FACE_OUTER_BOUND ( 'NONE', #50359, .T. ) ; +#5514 = STYLED_ITEM ( 'NONE', ( #83493 ), #27651 ) ; +#5515 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15244 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33573, #48886, #49372 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5516 = LINE ( 'NONE', #89818, #61630 ) ; +#5517 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93682, 'distance_accuracy_value', 'NONE'); +#5518 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5519 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999965514, 0.2500000000000000000, 0.6999285677838846809 ) ) ; +#5520 = AXIS2_PLACEMENT_3D ( 'NONE', #10334, #50288, #81425 ) ; +#5521 = LINE ( 'NONE', #44833, #56758 ) ; +#5522 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#5523 = ORIENTED_EDGE ( 'NONE', *, *, #4413, .T. ) ; +#5524 = ORIENTED_EDGE ( 'NONE', *, *, #76198, .F. ) ; +#5526 = AXIS2_PLACEMENT_3D ( 'NONE', #59936, #99602, #83393 ) ; +#5525 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88945 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62882, #50582, #88857 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5527 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48899, 'distance_accuracy_value', 'NONE'); +#5528 = ORIENTED_EDGE ( 'NONE', *, *, #32823, .T. ) ; +#5529 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5530 = VECTOR ( 'NONE', #58043, 1000.000000000000000 ) ; +#5531 = EDGE_CURVE ( 'NONE', #68868, #42687, #97082, .T. ) ; +#5532 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#5533 = FILL_AREA_STYLE ('',( #58238 ) ) ; +#5534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77345 ), #66008 ) ; +#5535 = FILL_AREA_STYLE_COLOUR ( '', #59459 ) ; +#5536 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5537 = SURFACE_STYLE_FILL_AREA ( #44353 ) ; +#5538 = CARTESIAN_POINT ( 'NONE', ( -1.261022403107399992, -0.9825712221600161334, 0.8299999999999999600 ) ) ; +#5539 = PRESENTATION_STYLE_ASSIGNMENT (( #75523 ) ) ; +#5541 = ORIENTED_EDGE ( 'NONE', *, *, #49036, .F. ) ; +#5540 = VERTEX_POINT ( 'NONE', #81327 ) ; +#5542 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38, #54710, #78175 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5543 = ORIENTED_EDGE ( 'NONE', *, *, #57451, .T. ) ; +#5544 = CARTESIAN_POINT ( 'NONE', ( 1.688788655318779863, -0.9001377335631758347, 0.8099999999999981659 ) ) ; +#5546 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#5545 = SURFACE_SIDE_STYLE ('',( #42888 ) ) ; +#5547 = VECTOR ( 'NONE', #30058, 1000.000000000000000 ) ; +#5548 = ORIENTED_EDGE ( 'NONE', *, *, #56579, .F. ) ; +#5549 = EDGE_CURVE ( 'NONE', #89365, #10551, #11247, .T. ) ; +#5550 = VERTEX_POINT ( 'NONE', #51175 ) ; +#5551 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#5552 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.000000000000000000 ) ) ; +#5554 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000002623, 0.2500000000000000555, -0.8499999999999999778 ) ) ; +#5553 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5555 = FILL_AREA_STYLE_COLOUR ( '', #8220 ) ; +#5556 = EDGE_LOOP ( 'NONE', ( #95852, #72124, #55075, #11038, #69994, #33380 ) ) ; +#5557 = ORIENTED_EDGE ( 'NONE', *, *, #45588, .T. ) ; +#5558 = STYLED_ITEM ( 'NONE', ( #74803 ), #72279 ) ; +#5559 = EDGE_LOOP ( 'NONE', ( #10395, #26301, #98156, #77059 ) ) ; +#5560 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5561 = FILL_AREA_STYLE ('',( #98442 ) ) ; +#5562 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#5563 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69099 ) ) ; +#5565 = VERTEX_POINT ( 'NONE', #12265 ) ; +#5564 = SURFACE_STYLE_USAGE ( .BOTH. , #75551 ) ; +#5566 = ADVANCED_FACE ( 'NONE', ( #73638 ), #73139, .F. ) ; +#5567 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88718 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91472, #99534, #84313 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5568 = ORIENTED_EDGE ( 'NONE', *, *, #35994, .F. ) ; +#5569 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.600000000000000089, -0.2000000000000000111 ) ) ; +#5570 = ORIENTED_EDGE ( 'NONE', *, *, #85076, .T. ) ; +#5571 = ORIENTED_EDGE ( 'NONE', *, *, #67966, .T. ) ; +#5572 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5573 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5574 = VECTOR ( 'NONE', #66954, 1000.000000000000000 ) ; +#5575 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#5576 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5577 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5578 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5579 = EDGE_CURVE ( 'NONE', #79785, #5810, #60354, .T. ) ; +#5580 = LINE ( 'NONE', #36776, #95415 ) ; +#5581 = ORIENTED_EDGE ( 'NONE', *, *, #78053, .T. ) ; +#5582 = SURFACE_STYLE_FILL_AREA ( #36290 ) ; +#5583 = AXIS2_PLACEMENT_3D ( 'NONE', #4437, #88709, #3942 ) ; +#5584 = VERTEX_POINT ( 'NONE', #45450 ) ; +#5585 = SURFACE_SIDE_STYLE ('',( #43926 ) ) ; +#5586 = CARTESIAN_POINT ( 'NONE', ( -0.3050011667720459729, -1.377680218341680085, 0.8299999999999999600 ) ) ; +#5587 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#5589 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#5588 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#5590 = AXIS2_PLACEMENT_3D ( 'NONE', #17939, #49137, #10204 ) ; +#5591 = CARTESIAN_POINT ( 'NONE', ( 1.757815472291410330, -1.145059460293619935, 0.8299999999999999600 ) ) ; +#5592 = SURFACE_SIDE_STYLE ('',( #74088 ) ) ; +#5593 = PRESENTATION_STYLE_ASSIGNMENT (( #44906 ) ) ; +#5594 = SURFACE_STYLE_USAGE ( .BOTH. , #80885 ) ; +#5596 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69204 ) ) ; +#5595 = AXIS2_PLACEMENT_3D ( 'NONE', #97241, #4343, #74297 ) ; +#5597 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5598 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.399999999999999911, -11.91999999999999993 ) ) ; +#5599 = FILL_AREA_STYLE ('',( #37795 ) ) ; +#5600 = FILL_AREA_STYLE_COLOUR ( '', #31018 ) ; +#5601 = VECTOR ( 'NONE', #14247, 999.9999999999998863 ) ; +#5602 = VECTOR ( 'NONE', #34575, 1000.000000000000000 ) ; +#5603 = EDGE_CURVE ( 'NONE', #20105, #3470, #84302, .T. ) ; +#5604 = FACE_OUTER_BOUND ( 'NONE', #65961, .T. ) ; +#5605 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#5606 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#5607 = SURFACE_STYLE_USAGE ( .BOTH. , #37320 ) ; +#5608 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#5609 = VECTOR ( 'NONE', #26118, 999.9999999999998863 ) ; +#5610 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9083, 'distance_accuracy_value', 'NONE'); +#5611 = ORIENTED_EDGE ( 'NONE', *, *, #10072, .F. ) ; +#5612 = EDGE_CURVE ( 'NONE', #87468, #7769, #29830, .T. ) ; +#5613 = LINE ( 'NONE', #12232, #53807 ) ; +#5614 = FILL_AREA_STYLE ('',( #37330 ) ) ; +#5615 = LINE ( 'NONE', #61323, #90169 ) ; +#5616 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5617 = CARTESIAN_POINT ( 'NONE', ( 0.4257071878237467244, -1.173902881467449033, 0.8100000000000002753 ) ) ; +#5618 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#5619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36667 ) ) ; +#5620 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#5621 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#5622 = VECTOR ( 'NONE', #1736, 1000.000000000000114 ) ; +#5623 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, 0.000000000000000000 ) ) ; +#5624 = SURFACE_STYLE_FILL_AREA ( #13244 ) ; +#5625 = ORIENTED_EDGE ( 'NONE', *, *, #83266, .F. ) ; +#5626 = ORIENTED_EDGE ( 'NONE', *, *, #85154, .F. ) ; +#5627 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.004999999999999986226, -0.2399999999999999911 ) ) ; +#5628 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#5629 = FACE_OUTER_BOUND ( 'NONE', #59251, .T. ) ; +#5630 = LINE ( 'NONE', #13254, #417 ) ; +#5631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66183 ), #82369 ) ; +#5632 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5633 = STYLED_ITEM ( 'NONE', ( #54634 ), #54003 ) ; +#5634 = LINE ( 'NONE', #60345, #19244 ) ; +#5635 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5636 = VERTEX_POINT ( 'NONE', #90961 ) ; +#5637 = PRESENTATION_STYLE_ASSIGNMENT (( #13781 ) ) ; +#5638 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5639 = VERTEX_POINT ( 'NONE', #76628 ) ; +#5640 = AXIS2_PLACEMENT_3D ( 'NONE', #91969, #13811, #83333 ) ; +#5641 = AXIS2_PLACEMENT_3D ( 'NONE', #64183, #56035, #57055 ) ; +#5642 = FACE_OUTER_BOUND ( 'NONE', #41034, .T. ) ; +#5643 = ORIENTED_EDGE ( 'NONE', *, *, #25064, .T. ) ; +#5644 = VECTOR ( 'NONE', #71359, 1000.000000000000000 ) ; +#5645 = VECTOR ( 'NONE', #74063, 1000.000000000000000 ) ; +#5646 = EDGE_CURVE ( 'NONE', #43256, #27634, #30152, .T. ) ; +#5647 = ADVANCED_FACE ( 'NONE', ( #5642 ), #59861, .T. ) ; +#5648 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000000278, 0.8648700000000000276 ) ) ; +#5649 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#5650 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 2.983172999999999853, 0.8648700000000000276 ) ) ; +#5651 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5653 = ORIENTED_EDGE ( 'NONE', *, *, #54626, .F. ) ; +#5652 = VERTEX_POINT ( 'NONE', #36346 ) ; +#5654 = PRESENTATION_STYLE_ASSIGNMENT (( #22520 ) ) ; +#5655 = ORIENTED_EDGE ( 'NONE', *, *, #94935, .T. ) ; +#5656 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5657 = CIRCLE ( 'NONE', #25279, 0.2000000000000000111 ) ; +#5658 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#5659 = ORIENTED_EDGE ( 'NONE', *, *, #63798, .T. ) ; +#5660 = EDGE_CURVE ( 'NONE', #71740, #34164, #91949, .T. ) ; +#5661 = ORIENTED_EDGE ( 'NONE', *, *, #98585, .F. ) ; +#5662 = EDGE_CURVE ( 'NONE', #27237, #68594, #52178, .T. ) ; +#5663 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36707 ), #13806 ) ; +#5664 = VECTOR ( 'NONE', #34449, 1000.000000000000000 ) ; +#5665 = CARTESIAN_POINT ( 'NONE', ( -0.5440966885710070144, -1.187196157070490088, 0.8100000000000000533 ) ) ; +#5667 = FACE_OUTER_BOUND ( 'NONE', #60030, .T. ) ; +#5666 = FACE_OUTER_BOUND ( 'NONE', #18785, .T. ) ; +#5668 = EDGE_LOOP ( 'NONE', ( #956, #68451, #87212, #21811 ) ) ; +#5669 = EDGE_LOOP ( 'NONE', ( #10261, #34138, #76611, #85704 ) ) ; +#5670 = ORIENTED_EDGE ( 'NONE', *, *, #93728, .T. ) ; +#5671 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85489, #31882, #100197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5672 = SURFACE_STYLE_FILL_AREA ( #85322 ) ; +#5673 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38290 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66130, #27334, #67599 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5674 = ORIENTED_EDGE ( 'NONE', *, *, #33283, .F. ) ; +#5676 = EDGE_CURVE ( 'NONE', #48890, #55931, #52671, .T. ) ; +#5675 = AXIS2_PLACEMENT_3D ( 'NONE', #79491, #33533, #2884 ) ; +#5677 = FILL_AREA_STYLE ('',( #27230 ) ) ; +#5678 = CARTESIAN_POINT ( 'NONE', ( 10.77310724974991274, 7.261168750250087456, 0.8991599999999999593 ) ) ; +#5679 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5680 = ORIENTED_EDGE ( 'NONE', *, *, #82678, .F. ) ; +#5681 = LINE ( 'NONE', #69352, #89628 ) ; +#5682 = SHAPE_REPRESENTATION ( 'C0402_20210301.xtd', ( #82894 ), #79436 ) ; +#5683 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#5684 = ORIENTED_EDGE ( 'NONE', *, *, #92396, .F. ) ; +#5685 = EDGE_CURVE ( 'NONE', #62366, #93940, #22006, .T. ) ; +#5686 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5687 = FACE_OUTER_BOUND ( 'NONE', #39375, .T. ) ; +#5688 = LINE ( 'NONE', #32123, #71201 ) ; +#5689 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5690 = VECTOR ( 'NONE', #98456, 1000.000000000000114 ) ; +#5691 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#5692 = CARTESIAN_POINT ( 'NONE', ( 1.823120247820650297, -1.344848644821849959, 0.8100000000000000533 ) ) ; +#5693 = EDGE_CURVE ( 'NONE', #15757, #64282, #87315, .T. ) ; +#5694 = CARTESIAN_POINT ( 'NONE', ( -1.130406177152237790, -1.157551243805461150, 0.8099999999998720446 ) ) ; +#5695 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5697 = EDGE_CURVE ( 'NONE', #67641, #58676, #62857, .T. ) ; +#5696 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#5698 = ORIENTED_EDGE ( 'NONE', *, *, #13575, .T. ) ; +#5699 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5700 = LINE ( 'NONE', #12325, #89055 ) ; +#5701 = ADVANCED_FACE ( 'NONE', ( #17352 ), #38848, .T. ) ; +#5702 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84032 ), #44853 ) ; +#5703 = AXIS2_PLACEMENT_3D ( 'NONE', #989, #15773, #87254 ) ; +#5704 = SURFACE_SIDE_STYLE ('',( #44527 ) ) ; +#5706 = CARTESIAN_POINT ( 'NONE', ( 1.575220826706200006, -1.366783821657739928, 0.8299999999999999600 ) ) ; +#5705 = LINE ( 'NONE', #68008, #69056 ) ; +#5707 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#5708 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5709 = PRODUCT_DEFINITION ( 'δ֪', '', #14349, #25915 ) ; +#5710 = AXIS2_PLACEMENT_3D ( 'NONE', #74731, #19078, #27787 ) ; +#5711 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5712 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01085786437626904723, 0.1500000000000000222 ) ) ; +#5713 = STYLED_ITEM ( 'NONE', ( #42658 ), #78084 ) ; +#5714 = VERTEX_POINT ( 'NONE', #32200 ) ; +#5715 = VECTOR ( 'NONE', #42739, 1000.000000000000000 ) ; +#5716 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16038 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8155, #88884, #80235 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5717 = LINE ( 'NONE', #14878, #84097 ) ; +#5718 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5719 = ORIENTED_EDGE ( 'NONE', *, *, #1715, .T. ) ; +#5720 = EDGE_CURVE ( 'NONE', #5748, #52472, #78639, .T. ) ; +#5722 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8648700000000000276 ) ) ; +#5721 = VECTOR ( 'NONE', #95980, 1000.000000000000000 ) ; +#5724 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.60762199999999922, 0.8648700000000000276 ) ) ; +#5723 = FILL_AREA_STYLE_COLOUR ( '', #16422 ) ; +#5725 = SURFACE_STYLE_USAGE ( .BOTH. , #67048 ) ; +#5726 = SURFACE_SIDE_STYLE ('',( #75713 ) ) ; +#5727 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5728 = AXIS2_PLACEMENT_3D ( 'NONE', #47878, #78502, #39199 ) ; +#5729 = ORIENTED_EDGE ( 'NONE', *, *, #4238, .F. ) ; +#5730 = SURFACE_STYLE_FILL_AREA ( #45525 ) ; +#5731 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5732 = PLANE ( 'NONE', #78359 ) ; +#5735 = VECTOR ( 'NONE', #25138, 1000.000000000000000 ) ; +#5734 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93775 ) ) ; +#5733 = FACE_OUTER_BOUND ( 'NONE', #45242, .T. ) ; +#5736 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5737 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5738 = FILL_AREA_STYLE_COLOUR ( '', #12598 ) ; +#5739 = FILL_AREA_STYLE ('',( #98132 ) ) ; +#5740 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#5741 = FILL_AREA_STYLE_COLOUR ( '', #8267 ) ; +#5742 = EDGE_CURVE ( 'NONE', #67111, #13289, #69967, .T. ) ; +#5743 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#5744 = FILL_AREA_STYLE_COLOUR ( '', #91986 ) ; +#5745 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5746 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8648700000000000276 ) ) ; +#5747 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#5748 = VERTEX_POINT ( 'NONE', #19 ) ; +#5749 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#5750 = ORIENTED_EDGE ( 'NONE', *, *, #28278, .T. ) ; +#5751 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97092 ) ) ; +#5752 = SURFACE_STYLE_USAGE ( .BOTH. , #91062 ) ; +#5753 = CARTESIAN_POINT ( 'NONE', ( 1.062208424706029941, -1.030374455384980070, 0.8100000000000000533 ) ) ; +#5754 = FILL_AREA_STYLE_COLOUR ( '', #29935 ) ; +#5755 = FILL_AREA_STYLE ('',( #45549 ) ) ; +#5756 = AXIS2_PLACEMENT_3D ( 'NONE', #30035, #9004, #41754 ) ; +#5757 = PRESENTATION_STYLE_ASSIGNMENT (( #75740 ) ) ; +#5758 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#5759 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8648700000000000276 ) ) ; +#5760 = PRESENTATION_STYLE_ASSIGNMENT (( #68063 ) ) ; +#5761 = ORIENTED_EDGE ( 'NONE', *, *, #50774, .F. ) ; +#5762 = PRESENTATION_STYLE_ASSIGNMENT (( #68066 ) ) ; +#5763 = FILL_AREA_STYLE_COLOUR ( '', #3054 ) ; +#5764 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -1.224646799147353207E-16 ) ) ; +#5765 = SURFACE_STYLE_USAGE ( .BOTH. , #42616 ) ; +#5766 = ORIENTED_EDGE ( 'NONE', *, *, #69553, .F. ) ; +#5767 = FILL_AREA_STYLE ('',( #28302 ) ) ; +#5768 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39261, #23986, #57658 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5769 = EDGE_CURVE ( 'NONE', #934, #5935, #94452, .T. ) ; +#5770 = CARTESIAN_POINT ( 'NONE', ( 1.347634412165590101, -1.485054850390570058, 0.8299999999999994049 ) ) ; +#5771 = VECTOR ( 'NONE', #46525, 1000.000000000000000 ) ; +#5772 = CARTESIAN_POINT ( 'NONE', ( -1.263508545851719900, -1.411115659170130154, 0.8299999999999999600 ) ) ; +#5773 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#5774 = FILL_AREA_STYLE_COLOUR ( '', #91928 ) ; +#5775 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#5776 = ORIENTED_EDGE ( 'NONE', *, *, #53754, .T. ) ; +#5777 = PLANE ( 'NONE', #22796 ) ; +#5778 = SURFACE_STYLE_FILL_AREA ( #82441 ) ; +#5779 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#5780 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27059 ), #4220 ) ; +#5781 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85693 ), #71055 ) ; +#5782 = FILL_AREA_STYLE_COLOUR ( '', #1163 ) ; +#5783 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8221 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11401, #82459, #65609 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5784 = ORIENTED_EDGE ( 'NONE', *, *, #14428, .F. ) ; +#5785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51496 ) ) ; +#5786 = EDGE_CURVE ( 'NONE', #45110, #54210, #56200, .T. ) ; +#5787 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49886 ) ) ; +#5788 = LINE ( 'NONE', #43611, #85608 ) ; +#5789 = FILL_AREA_STYLE ('',( #67587 ) ) ; +#5790 = FILL_AREA_STYLE ('',( #37495 ) ) ; +#5791 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8648700000000000276 ) ) ; +#5792 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12172 ), #87318 ) ; +#5793 = ORIENTED_EDGE ( 'NONE', *, *, #31913, .F. ) ; +#5794 = ADVANCED_FACE ( 'NONE', ( #78159 ), #23537, .F. ) ; +#5795 = FACE_OUTER_BOUND ( 'NONE', #12307, .T. ) ; +#5796 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #11238, #4658 ), + ( #50666, #3665 ), + ( #42972, #74126 ), + ( #98027, #19985 ), + ( #2678, #28168 ), + ( #4173, #80800 ), + ( #82301, #34847 ), + ( #41483, #80289 ), + ( #33831, #65964 ), + ( #96566, #64954 ), + ( #34344, #26678 ), + ( #83301, #45437 ), + ( #92424, #7088 ), + ( #38336, #52654 ), + ( #37348, #99995 ), + ( #98510, #52167 ), + ( #68444, #100479 ), + ( #5136, #51673 ), + ( #84775, #75139 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06671213312217240399, 0.1318787174909979987, 0.1956920876010850019, 0.2591665434654509825, 0.3214355090977070173, 0.3819902024751150038, 0.4405918594941419797, 0.4988820194811739994, 0.5568214512511839853, 0.6142910636512469713, 0.6729433513772560271, 0.7334980447546629589, 0.7961187704913560426, 0.8606751674120489692, 0.9282127582381539677, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#5797 = AXIS2_PLACEMENT_3D ( 'NONE', #61747, #53069, #16227 ) ; +#5798 = ORIENTED_EDGE ( 'NONE', *, *, #56468, .T. ) ; +#5799 = ORIENTED_EDGE ( 'NONE', *, *, #76978, .F. ) ; +#5800 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79610, 'distance_accuracy_value', 'NONE'); +#5801 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#5803 = CARTESIAN_POINT ( 'NONE', ( -1.219099199802559985, -1.508462442331270026, 0.8100000000000000533 ) ) ; +#5802 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5804 = CARTESIAN_POINT ( 'NONE', ( -2.676179938779915002, 3.100000000000000089, 0.000000000000000000 ) ) ; +#5805 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36837 ) ) ; +#5806 = ORIENTED_EDGE ( 'NONE', *, *, #20020, .F. ) ; +#5807 = PRESENTATION_STYLE_ASSIGNMENT (( #52335 ) ) ; +#5808 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.251909075926969983, 0.8100000000000000533 ) ) ; +#5809 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5810 = VERTEX_POINT ( 'NONE', #49543 ) ; +#5811 = LINE ( 'NONE', #7275, #23702 ) ; +#5812 = PLANE ( 'NONE', #91951 ) ; +#5813 = DIRECTION ( 'NONE', ( -0.9961493162234444920, 0.08767291364819436439, 0.000000000000000000 ) ) ; +#5814 = EDGE_LOOP ( 'NONE', ( #47265, #74140, #73935, #11161 ) ) ; +#5816 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5815 = PLANE ( 'NONE', #12655 ) ; +#5817 = ORIENTED_EDGE ( 'NONE', *, *, #98949, .T. ) ; +#5818 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64542 ), #4260 ) ; +#5819 = CARTESIAN_POINT ( 'NONE', ( -0.1591923701298700033, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#5820 = CARTESIAN_POINT ( 'NONE', ( 3.666684875124987197, 7.848067124875013789, 0.8648700000000000276 ) ) ; +#5821 = EDGE_CURVE ( 'NONE', #6846, #6445, #10618, .T. ) ; +#5822 = ORIENTED_EDGE ( 'NONE', *, *, #16873, .F. ) ; +#5823 = ORIENTED_EDGE ( 'NONE', *, *, #23911, .F. ) ; +#5824 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#5825 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5826 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#5827 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#5828 = LINE ( 'NONE', #76822, #75682 ) ; +#5829 = PLANE ( 'NONE', #14864 ) ; +#5830 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5831 = CARTESIAN_POINT ( 'NONE', ( 1.341536415582540220, -1.062017517080650064, 0.8100000000000000533 ) ) ; +#5832 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, 0.000000000000000000 ) ) ; +#5833 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#5834 = ORIENTED_EDGE ( 'NONE', *, *, #61580, .T. ) ; +#5835 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#5837 = VECTOR ( 'NONE', #70796, 1000.000000000000000 ) ; +#5836 = LINE ( 'NONE', #4863, #38261 ) ; +#5838 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.266666666666659946, 0.000000000000000000 ) ) ; +#5839 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49268, 'distance_accuracy_value', 'NONE'); +#5840 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5841 = SURFACE_STYLE_FILL_AREA ( #52875 ) ; +#5842 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#5843 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5844 = ORIENTED_EDGE ( 'NONE', *, *, #30908, .F. ) ; +#5846 = EDGE_CURVE ( 'NONE', #57013, #89137, #40879, .T. ) ; +#5845 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70586 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79827, #49183, #63006 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5847 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5848 = LINE ( 'NONE', #13475, #57676 ) ; +#5849 = PLANE ( 'NONE', #27801 ) ; +#5850 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#5851 = CARTESIAN_POINT ( 'NONE', ( -0.03242561202523040059, -1.422222704560690110, 0.8100000000000000533 ) ) ; +#5852 = PRESENTATION_STYLE_ASSIGNMENT (( #75843 ) ) ; +#5853 = PLANE ( 'NONE', #36617 ) ; +#5854 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#5855 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84182 ), #28712 ) ; +#5856 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72753 ), #12316 ) ; +#5857 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#5858 = FILL_AREA_STYLE_COLOUR ( '', #43497 ) ; +#5859 = SURFACE_STYLE_USAGE ( .BOTH. , #75349 ) ; +#5860 = PLANE ( 'NONE', #69566 ) ; +#5861 = CARTESIAN_POINT ( 'NONE', ( -2.183333333333333570, -3.100000000000000533, 0.000000000000000000 ) ) ; +#5862 = PLANE ( 'NONE', #22988 ) ; +#5863 = SURFACE_SIDE_STYLE ('',( #53383 ) ) ; +#5864 = STYLED_ITEM ( 'NONE', ( #16779 ), #61862 ) ; +#5865 = FILL_AREA_STYLE_COLOUR ( '', #23568 ) ; +#5866 = EDGE_CURVE ( 'NONE', #71240, #54228, #64845, .T. ) ; +#5867 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5868 = SURFACE_STYLE_USAGE ( .BOTH. , #84522 ) ; +#5869 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.266666666666659946, 0.000000000000000000 ) ) ; +#5871 = EDGE_CURVE ( 'NONE', #59381, #99050, #11629, .T. ) ; +#5870 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.876179938779915179, -0.02000000000000000042 ) ) ; +#5872 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#5873 = ORIENTED_EDGE ( 'NONE', *, *, #84874, .F. ) ; +#5874 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#5875 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46649 ) ) ; +#5876 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#5877 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000533, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#5878 = VECTOR ( 'NONE', #30012, 1000.000000000000000 ) ; +#5879 = EDGE_CURVE ( 'NONE', #9920, #56959, #2564, .T. ) ; +#5880 = EDGE_CURVE ( 'NONE', #10140, #919, #89826, .T. ) ; +#5881 = VECTOR ( 'NONE', #51331, 1000.000000000000000 ) ; +#5882 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#5883 = FACE_OUTER_BOUND ( 'NONE', #26090, .T. ) ; +#5884 = SURFACE_STYLE_FILL_AREA ( #28913 ) ; +#5885 = AXIS2_PLACEMENT_3D ( 'NONE', #86602, #54983, #9427 ) ; +#5886 = EDGE_LOOP ( 'NONE', ( #18623, #21175, #25006, #84222, #55668, #37102 ) ) ; +#5887 = EDGE_CURVE ( 'NONE', #67839, #23538, #19886, .T. ) ; +#5888 = ADVANCED_FACE ( 'NONE', ( #57728 ), #72492, .F. ) ; +#5889 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17372 ), #74474 ) ; +#5890 = FILL_AREA_STYLE ('',( #22267 ) ) ; +#5891 = FILL_AREA_STYLE ('',( #75885 ) ) ; +#5892 = VERTEX_POINT ( 'NONE', #58727 ) ; +#5893 = ORIENTED_EDGE ( 'NONE', *, *, #98066, .F. ) ; +#5894 = EDGE_CURVE ( 'NONE', #24683, #13552, #3573, .T. ) ; +#5895 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5896 = ORIENTED_EDGE ( 'NONE', *, *, #49486, .T. ) ; +#5897 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#5898 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30329 ) ) ; +#5899 = CARTESIAN_POINT ( 'NONE', ( 0.5451074176016761363, -1.092033457943389907, 0.8100000000000000533 ) ) ; +#5900 = LINE ( 'NONE', #82573, #81011 ) ; +#5901 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5902 = CARTESIAN_POINT ( 'NONE', ( 10.92867087512504298, 5.422690875125044663, 0.8648700000000000276 ) ) ; +#5903 = EDGE_CURVE ( 'NONE', #7870, #60865, #65860, .T. ) ; +#5904 = ORIENTED_EDGE ( 'NONE', *, *, #92165, .F. ) ; +#5905 = ORIENTED_EDGE ( 'NONE', *, *, #58267, .F. ) ; +#5906 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000000291, -0.2400000000000000189 ) ) ; +#5907 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000006162, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#5908 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64712 ) ) ; +#5909 = VECTOR ( 'NONE', #63327, 1000.000000000000000 ) ; +#5910 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37855, 'distance_accuracy_value', 'NONE'); +#5911 = FACE_OUTER_BOUND ( 'NONE', #89313, .T. ) ; +#5912 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5913 = STYLED_ITEM ( 'NONE', ( #92285 ), #54726 ) ; +#5914 = PRESENTATION_STYLE_ASSIGNMENT (( #44744 ) ) ; +#5915 = FILL_AREA_STYLE ('',( #100278 ) ) ; +#5916 = VECTOR ( 'NONE', #69883, 1000.000000000000000 ) ; +#5917 = CARTESIAN_POINT ( 'NONE', ( -1.235751819672409990, -0.8946064028769500354, 0.8299999999999999600 ) ) ; +#5918 = ORIENTED_EDGE ( 'NONE', *, *, #12504, .F. ) ; +#5919 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5920 = VERTEX_POINT ( 'NONE', #50562 ) ; +#5921 = ORIENTED_EDGE ( 'NONE', *, *, #64133, .F. ) ; +#5922 = VECTOR ( 'NONE', #93308, 1000.000000000000000 ) ; +#5923 = LINE ( 'NONE', #98817, #46589 ) ; +#5924 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#5926 = ADVANCED_FACE ( 'NONE', ( #33211 ), #81696, .T. ) ; +#5925 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#5927 = EDGE_LOOP ( 'NONE', ( #91730, #75191, #12222, #82567, #10499, #61545 ) ) ; +#5928 = STYLED_ITEM ( 'NONE', ( #95284 ), #40884 ) ; +#5929 = VECTOR ( 'NONE', #6247, 1000.000000000000000 ) ; +#5930 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5931 = SURFACE_STYLE_FILL_AREA ( #5436 ) ; +#5932 = ORIENTED_EDGE ( 'NONE', *, *, #73321, .T. ) ; +#5933 = SURFACE_STYLE_FILL_AREA ( #68256 ) ; +#5934 = LINE ( 'NONE', #65785, #8565 ) ; +#5935 = VERTEX_POINT ( 'NONE', #29061 ) ; +#5936 = ADVANCED_FACE ( 'NONE', ( #91816 ), #21889, .T. ) ; +#5937 = ORIENTED_EDGE ( 'NONE', *, *, #20669, .F. ) ; +#5939 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.000000000000000000 ) ) ; +#5938 = CARTESIAN_POINT ( 'NONE', ( 0.9586437380306700451, -1.309512843728070086, 0.8299999999999999600 ) ) ; +#5940 = FILL_AREA_STYLE ('',( #52474 ) ) ; +#5941 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5942 = SURFACE_SIDE_STYLE ('',( #29485 ) ) ; +#5943 = CARTESIAN_POINT ( 'NONE', ( -0.008157340354953810171, -1.074567238704529970, 0.8100000000000000533 ) ) ; +#5944 = VECTOR ( 'NONE', #7856, 1000.000000000000000 ) ; +#5945 = SURFACE_SIDE_STYLE ('',( #98838 ) ) ; +#5946 = FACE_OUTER_BOUND ( 'NONE', #99604, .T. ) ; +#5947 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2676 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31223, #93468, #39374 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5948 = ORIENTED_EDGE ( 'NONE', *, *, #33809, .T. ) ; +#5949 = ORIENTED_EDGE ( 'NONE', *, *, #10020, .F. ) ; +#5950 = PLANE ( 'NONE', #11361 ) ; +#5951 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5952 = SURFACE_STYLE_USAGE ( .BOTH. , #62178 ) ; +#5953 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#5954 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8648700000000000276 ) ) ; +#5955 = PRESENTATION_STYLE_ASSIGNMENT (( #20837 ) ) ; +#5956 = VERTEX_POINT ( 'NONE', #30032 ) ; +#5957 = EDGE_CURVE ( 'NONE', #28448, #44731, #83688, .T. ) ; +#5958 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8099999999998663824 ) ) ; +#5959 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#5960 = FILL_AREA_STYLE_COLOUR ( '', #95221 ) ; +#5961 = SURFACE_STYLE_FILL_AREA ( #38670 ) ; +#5962 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#5963 = PLANE ( 'NONE', #3420 ) ; +#5964 = FILL_AREA_STYLE ('',( #68780 ) ) ; +#5965 = LINE ( 'NONE', #28510, #74504 ) ; +#5966 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#5967 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17446 ) ) ; +#5968 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#5969 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5970 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5971 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#5972 = CARTESIAN_POINT ( 'NONE', ( 1.209440659729950074, -0.9548508715965590143, 0.8299999999999995159 ) ) ; +#5973 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43236 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55919, #1261, #32922 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#5974 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #10396, #50361, #20666, #51840 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#5975 = ORIENTED_EDGE ( 'NONE', *, *, #5070, .F. ) ; +#5976 = FILL_AREA_STYLE_COLOUR ( '', #76259 ) ; +#5977 = EDGE_LOOP ( 'NONE', ( #41398, #78061, #89705, #56086 ) ) ; +#5978 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#5980 = AXIS2_PLACEMENT_3D ( 'NONE', #9961, #82030, #88665 ) ; +#5979 = FILL_AREA_STYLE ('',( #28524 ) ) ; +#5981 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8991599999999999593 ) ) ; +#5982 = FACE_OUTER_BOUND ( 'NONE', #94249, .T. ) ; +#5984 = PLANE ( 'NONE', #29712 ) ; +#5983 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5985 = CARTESIAN_POINT ( 'NONE', ( 1.264852522887508268, -0.8857285283026522515, 0.8100000000000616707 ) ) ; +#5986 = PRESENTATION_STYLE_ASSIGNMENT (( #14161 ) ) ; +#5988 = ORIENTED_EDGE ( 'NONE', *, *, #20624, .T. ) ; +#5987 = AXIS2_PLACEMENT_3D ( 'NONE', #96974, #58247, #41889 ) ; +#5989 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#5990 = FACE_OUTER_BOUND ( 'NONE', #52936, .T. ) ; +#5991 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#5992 = ADVANCED_FACE ( 'NONE', ( #82198 ), #12143, .F. ) ; +#5993 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#5994 = CARTESIAN_POINT ( 'NONE', ( 3.100999499500048273, 7.282381500499949034, 0.8991599999999999593 ) ) ; +#5995 = VECTOR ( 'NONE', #14301, 1000.000000000000000 ) ; +#5996 = FILL_AREA_STYLE_COLOUR ( '', #38212 ) ; +#5997 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#5998 = CLOSED_SHELL ( 'NONE', ( #9657, #50072, #79274, #70630, #36424, #56226 ) ) ; +#5999 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6001 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49148 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58559, #53363, #92627 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6000 = SURFACE_STYLE_FILL_AREA ( #48805 ) ; +#6002 = ORIENTED_EDGE ( 'NONE', *, *, #51048, .T. ) ; +#6003 = ORIENTED_EDGE ( 'NONE', *, *, #75676, .F. ) ; +#6004 = AXIS2_PLACEMENT_3D ( 'NONE', #21008, #63363, #54157 ) ; +#6005 = EDGE_CURVE ( 'NONE', #34720, #4894, #54044, .T. ) ; +#6006 = VERTEX_POINT ( 'NONE', #92791 ) ; +#6007 = CARTESIAN_POINT ( 'NONE', ( -0.2819971453420380136, -1.430103682213279992, 0.8299999999999999600 ) ) ; +#6008 = VECTOR ( 'NONE', #40370, 1000.000000000000000 ) ; +#6009 = LINE ( 'NONE', #96965, #15636 ) ; +#6010 = PRESENTATION_STYLE_ASSIGNMENT (( #6985 ) ) ; +#6011 = ADVANCED_FACE ( 'NONE', ( #78516 ), #47891, .T. ) ; +#6012 = AXIS2_PLACEMENT_3D ( 'NONE', #65902, #89868, #88877 ) ; +#6013 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6014 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#6015 = CARTESIAN_POINT ( 'NONE', ( -1.183862409742999944, -0.9551946040733080290, 0.8299999999999999600 ) ) ; +#6017 = EDGE_LOOP ( 'NONE', ( #77144, #36899, #30836, #70979 ) ) ; +#6016 = EDGE_LOOP ( 'NONE', ( #33026, #20886, #73790, #83091 ) ) ; +#6018 = ORIENTED_EDGE ( 'NONE', *, *, #2409, .T. ) ; +#6019 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#6020 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20457, 'distance_accuracy_value', 'NONE'); +#6022 = LINE ( 'NONE', #22402, #36583 ) ; +#6021 = PRESENTATION_STYLE_ASSIGNMENT (( #67843 ) ) ; +#6023 = ORIENTED_EDGE ( 'NONE', *, *, #32118, .F. ) ; +#6024 = ORIENTED_EDGE ( 'NONE', *, *, #34757, .F. ) ; +#6025 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#6026 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#6027 = FILL_AREA_STYLE ('',( #76039 ) ) ; +#6028 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#6029 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, -0.2458578643762690252 ) ) ; +#6031 = ORIENTED_EDGE ( 'NONE', *, *, #65652, .T. ) ; +#6030 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2829 ) ) ; +#6032 = ORIENTED_EDGE ( 'NONE', *, *, #24053, .T. ) ; +#6033 = VERTEX_POINT ( 'NONE', #15178 ) ; +#6034 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6035 = STYLED_ITEM ( 'NONE', ( #29978 ), #30716 ) ; +#6036 = LINE ( 'NONE', #73184, #39622 ) ; +#6038 = ORIENTED_EDGE ( 'NONE', *, *, #48143, .F. ) ; +#6037 = CARTESIAN_POINT ( 'NONE', ( -0.2382088481159115034, -1.394154587619768515, 0.8099999999996569944 ) ) ; +#6039 = FACE_OUTER_BOUND ( 'NONE', #64815, .T. ) ; +#6040 = VECTOR ( 'NONE', #65683, 1000.000000000000000 ) ; +#6041 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 4.397386000000000905, 0.8648700000000000276 ) ) ; +#6042 = ORIENTED_EDGE ( 'NONE', *, *, #77579, .F. ) ; +#6043 = CARTESIAN_POINT ( 'NONE', ( -0.01180881832068430073, -1.255590633215009966, 0.8299999999999999600 ) ) ; +#6044 = LINE ( 'NONE', #91379, #65666 ) ; +#6045 = ORIENTED_EDGE ( 'NONE', *, *, #93952, .F. ) ; +#6046 = EDGE_CURVE ( 'NONE', #80337, #39491, #94820, .T. ) ; +#6047 = VERTEX_POINT ( 'NONE', #31059 ) ; +#6048 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#6049 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65524, #65044, #26758, #73704, #13222, #57929, #76087, #44418, #88020, #75587, #89031, #11323, #96150, #42064, #3759, #5598 ), + .UNSPECIFIED., .F., .F., + ( 4, 3, 3, 3, 3, 4 ), + ( 0.000000000000000000, 1.663403519467404921E-05, 3.335286535631754983E-05, 4.905080406608849783E-05, 6.501029528148600557E-05, 8.039980370691709977E-05 ), + .UNSPECIFIED. ) ; +#6050 = FACE_OUTER_BOUND ( 'NONE', #17349, .T. ) ; +#6051 = PLANE ( 'NONE', #90472 ) ; +#6052 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43636 ), #56743 ) ; +#6053 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#6054 = SURFACE_STYLE_FILL_AREA ( #20429 ) ; +#6055 = LINE ( 'NONE', #45388, #78152 ) ; +#6057 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6056 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6058 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#6059 = VERTEX_POINT ( 'NONE', #15710 ) ; +#6060 = AXIS2_PLACEMENT_3D ( 'NONE', #68547, #35949, #83401 ) ; +#6061 = SURFACE_STYLE_USAGE ( .BOTH. , #53109 ) ; +#6062 = VERTEX_POINT ( 'NONE', #85679 ) ; +#6063 = AXIS2_PLACEMENT_3D ( 'NONE', #76732, #31272, #23132 ) ; +#6064 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93299 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74650, #60849, #30156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6065 = SURFACE_STYLE_USAGE ( .BOTH. , #5095 ) ; +#6066 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6067 = STYLED_ITEM ( 'NONE', ( #73899 ), #23346 ) ; +#6068 = SURFACE_STYLE_USAGE ( .BOTH. , #60788 ) ; +#6069 = CARTESIAN_POINT ( 'NONE', ( 1.773496746821729975, -1.132325613921520091, 0.8299999999999999600 ) ) ; +#6070 = CLOSED_SHELL ( 'NONE', ( #83757, #18929, #1444, #86715, #75804, #36937 ) ) ; +#6071 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#6073 = EDGE_CURVE ( 'NONE', #8086, #19782, #86200, .T. ) ; +#6072 = CARTESIAN_POINT ( 'NONE', ( -1.364612412596039936, -1.414598001867640065, 0.8300000000000024025 ) ) ; +#6074 = VECTOR ( 'NONE', #27060, 1000.000000000000114 ) ; +#6075 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#6076 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6077 = EDGE_CURVE ( 'NONE', #98596, #54195, #409, .T. ) ; +#6078 = AXIS2_PLACEMENT_3D ( 'NONE', #73447, #80612, #10533 ) ; +#6079 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#6081 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6080 = FILL_AREA_STYLE ('',( #13749 ) ) ; +#6082 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#6083 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#6084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82784 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80923, #51271, #26794 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6085 = ORIENTED_EDGE ( 'NONE', *, *, #95594, .T. ) ; +#6086 = FACE_OUTER_BOUND ( 'NONE', #92985, .T. ) ; +#6087 = EDGE_CURVE ( 'NONE', #50012, #54357, #9160, .T. ) ; +#6088 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74615, 'distance_accuracy_value', 'NONE'); +#6089 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92498, 'distance_accuracy_value', 'NONE'); +#6090 = EDGE_CURVE ( 'NONE', #23538, #75715, #16705, .T. ) ; +#6091 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6092 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6093 = FACE_OUTER_BOUND ( 'NONE', #70718, .T. ) ; +#6094 = FILL_AREA_STYLE ('',( #77107 ) ) ; +#6095 = FILL_AREA_STYLE_COLOUR ( '', #37273 ) ; +#6096 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6097 = STYLED_ITEM ( 'NONE', ( #3265 ), #74448 ) ; +#6098 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#6099 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#6100 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, -13.40000000000000036 ) ) ; +#6101 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55113 ) ) ; +#6102 = EDGE_LOOP ( 'NONE', ( #78951, #11143, #21292, #4083, #82593 ) ) ; +#6103 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6104 = ORIENTED_EDGE ( 'NONE', *, *, #70466, .F. ) ; +#6105 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6106 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67318, 'distance_accuracy_value', 'NONE'); +#6107 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32678, 'distance_accuracy_value', 'NONE'); +#6108 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#6109 = CARTESIAN_POINT ( 'NONE', ( -1.296446609406725958, 0.7099999999999999645, -1.049999999999999822 ) ) ; +#6110 = EDGE_CURVE ( 'NONE', #94369, #41395, #61724, .T. ) ; +#6111 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2436 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86674, #16676, #25422 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6112 = STYLED_ITEM ( 'NONE', ( #84501 ), #91103 ) ; +#6113 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6114 = FACE_OUTER_BOUND ( 'NONE', #42104, .T. ) ; +#6115 = FILL_AREA_STYLE ('',( #21997 ) ) ; +#6116 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333319537, -1.300000000000000266, 0.000000000000000000 ) ) ; +#6117 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.900000000000000799, -0.02000000000000419845 ) ) ; +#6118 = VERTEX_POINT ( 'NONE', #71371 ) ; +#6120 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6119 = AXIS2_PLACEMENT_3D ( 'NONE', #625, #22613, #62955 ) ; +#6121 = SURFACE_STYLE_USAGE ( .BOTH. , #91944 ) ; +#6122 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6123 = ORIENTED_EDGE ( 'NONE', *, *, #26245, .F. ) ; +#6124 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.500000000000000000, 0.8299999999999999600 ) ) ; +#6125 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6126 = VECTOR ( 'NONE', #12840, 1000.000000000000000 ) ; +#6127 = EDGE_LOOP ( 'NONE', ( #80905, #62217, #11573, #10536 ) ) ; +#6128 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#6129 = EDGE_CURVE ( 'NONE', #64125, #16108, #23932, .T. ) ; +#6130 = STYLED_ITEM ( 'NONE', ( #10397 ), #17216 ) ; +#6131 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6132 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6133 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22445 ), #25753 ) ; +#6134 = VECTOR ( 'NONE', #39183, 1000.000000000000000 ) ; +#6136 = EDGE_LOOP ( 'NONE', ( #45585, #31598, #19020, #70395, #91738, #2604, #57272 ) ) ; +#6135 = ORIENTED_EDGE ( 'NONE', *, *, #66337, .F. ) ; +#6138 = AXIS2_PLACEMENT_3D ( 'NONE', #40473, #8709, #48638 ) ; +#6137 = CARTESIAN_POINT ( 'NONE', ( -0.1591923701298700033, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#6139 = ORIENTED_EDGE ( 'NONE', *, *, #90038, .T. ) ; +#6140 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24162 ), #74513 ) ; +#6141 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000222, 0.1200000000000000094, 0.4000000000000000777 ) ) ; +#6142 = CLOSED_SHELL ( 'NONE', ( #38430, #39541, #56309, #18851, #28319, #68075 ) ) ; +#6143 = ORIENTED_EDGE ( 'NONE', *, *, #70804, .F. ) ; +#6144 = ORIENTED_EDGE ( 'NONE', *, *, #69531, .T. ) ; +#6145 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94228 ), #71451 ) ; +#6146 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6147 = LINE ( 'NONE', #83833, #12676 ) ; +#6148 = EDGE_CURVE ( 'NONE', #45252, #19543, #55078, .T. ) ; +#6150 = PRESENTATION_STYLE_ASSIGNMENT (( #45978 ) ) ; +#6149 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#6152 = ORIENTED_EDGE ( 'NONE', *, *, #17205, .T. ) ; +#6151 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95840 ) ) ; +#6153 = ORIENTED_EDGE ( 'NONE', *, *, #60630, .F. ) ; +#6154 = ORIENTED_EDGE ( 'NONE', *, *, #85734, .T. ) ; +#6155 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35626 ), #84485 ) ; +#6156 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.000000000000000000 ) ) ; +#6157 = EDGE_CURVE ( 'NONE', #62639, #4125, #32585, .T. ) ; +#6158 = AXIS2_PLACEMENT_3D ( 'NONE', #6303, #83489, #60528 ) ; +#6161 = ORIENTED_EDGE ( 'NONE', *, *, #15213, .T. ) ; +#6160 = CIRCLE ( 'NONE', #63336, 0.01000000000000002623 ) ; +#6159 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6162 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6163 = PRESENTATION_STYLE_ASSIGNMENT (( #83347 ) ) ; +#6164 = PLANE ( 'NONE', #51442 ) ; +#6165 = ORIENTED_EDGE ( 'NONE', *, *, #24455, .T. ) ; +#6166 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666633301, -2.100000000000000089, 0.000000000000000000 ) ) ; +#6167 = ORIENTED_EDGE ( 'NONE', *, *, #43066, .F. ) ; +#6168 = ADVANCED_FACE ( 'NONE', ( #78030 ), #81585, .T. ) ; +#6169 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6170 = FILL_AREA_STYLE ('',( #13308 ) ) ; +#6171 = STYLED_ITEM ( 'NONE', ( #59756 ), #50217 ) ; +#6172 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23001, #78124, #24025 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6173 = EDGE_LOOP ( 'NONE', ( #21932, #20120, #76769, #38006 ) ) ; +#6174 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#6175 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6177 = CARTESIAN_POINT ( 'NONE', ( 1.508691354424569919, -1.396584910994119966, 0.8299999999999999600 ) ) ; +#6176 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6178 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35653 ), #14356 ) ; +#6179 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8648700000000000276 ) ) ; +#6180 = FACE_OUTER_BOUND ( 'NONE', #82170, .T. ) ; +#6181 = ORIENTED_EDGE ( 'NONE', *, *, #46871, .T. ) ; +#6182 = VECTOR ( 'NONE', #13810, 1000.000000000000000 ) ; +#6183 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#6184 = STYLED_ITEM ( 'NONE', ( #86406 ), #91397 ) ; +#6186 = CARTESIAN_POINT ( 'NONE', ( 1.358897951836539830, -1.374487914949399592, 0.8099999999997543609 ) ) ; +#6185 = CARTESIAN_POINT ( 'NONE', ( 0.4344096565324859771, -0.9919132076701281386, 0.8100000000000000533 ) ) ; +#6187 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#6188 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6189 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6190 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6191 = PLANE ( 'NONE', #72135 ) ; +#6192 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61749 ), #81303 ) ; +#6193 = ORIENTED_EDGE ( 'NONE', *, *, #9341, .F. ) ; +#6194 = ADVANCED_FACE ( 'NONE', ( #42257 ), #2448, .T. ) ; +#6195 = EDGE_CURVE ( 'NONE', #12979, #95068, #26254, .T. ) ; +#6196 = SURFACE_SIDE_STYLE ('',( #23108 ) ) ; +#6197 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6198 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48423 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1206, #96502, #42913 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6199 = ORIENTED_EDGE ( 'NONE', *, *, #46893, .F. ) ; +#6201 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#6200 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6202 = LINE ( 'NONE', #99599, #30883 ) ; +#6203 = VECTOR ( 'NONE', #55521, 1000.000000000000000 ) ; +#6204 = CIRCLE ( 'NONE', #4659, 0.09999999999999999167 ) ; +#6205 = VECTOR ( 'NONE', #99640, 1000.000000000000000 ) ; +#6206 = SURFACE_SIDE_STYLE ('',( #28266 ) ) ; +#6207 = ORIENTED_EDGE ( 'NONE', *, *, #7069, .F. ) ; +#6208 = EDGE_CURVE ( 'NONE', #49689, #12898, #66233, .T. ) ; +#6209 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#6210 = EDGE_CURVE ( 'NONE', #71668, #54161, #3459, .T. ) ; +#6211 = PLANE ( 'NONE', #61253 ) ; +#6212 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#6213 = SURFACE_STYLE_USAGE ( .BOTH. , #67538 ) ; +#6214 = FILL_AREA_STYLE_COLOUR ( '', #71021 ) ; +#6215 = EDGE_CURVE ( 'NONE', #65764, #54997, #40916, .T. ) ; +#6216 = SURFACE_STYLE_USAGE ( .BOTH. , #13888 ) ; +#6217 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#6218 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6219 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75993, 'distance_accuracy_value', 'NONE'); +#6220 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50365 ), #12780 ) ; +#6221 = PLANE ( 'NONE', #66481 ) ; +#6222 = AXIS2_PLACEMENT_3D ( 'NONE', #24753, #89020, #2750 ) ; +#6223 = ORIENTED_EDGE ( 'NONE', *, *, #84358, .F. ) ; +#6224 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.000000000000000000 ) ) ; +#6225 = EDGE_LOOP ( 'NONE', ( #39224, #16194, #21514, #26578, #100153, #73818, #89690, #25469, #23274, #30054, #8648, #96742 ) ) ; +#6226 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60970, 'distance_accuracy_value', 'NONE'); +#6227 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97173, 'distance_accuracy_value', 'NONE'); +#6229 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6228 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49813, #80442, #80962, #43124 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#6230 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#6231 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6232 = ADVANCED_FACE ( 'NONE', ( #17231 ), #64719, .T. ) ; +#6233 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6234 = CARTESIAN_POINT ( 'NONE', ( 1.714851922897540071, -0.9003478538782040408, 0.8299999999999999600 ) ) ; +#6235 = LINE ( 'NONE', #21123, #97295 ) ; +#6236 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6237 = ORIENTED_EDGE ( 'NONE', *, *, #64193, .T. ) ; +#6238 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6239 = ADVANCED_FACE ( 'NONE', ( #74899 ), #37614, .T. ) ; +#6240 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34026, 'distance_accuracy_value', 'NONE'); +#6241 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01085786437626906804, 0.2434314575050762208 ) ) ; +#6242 = PRESENTATION_STYLE_ASSIGNMENT (( #100609 ) ) ; +#6243 = VECTOR ( 'NONE', #24410, 1000.000000000000000 ) ; +#6244 = VECTOR ( 'NONE', #72394, 1000.000000000000000 ) ; +#6245 = ORIENTED_EDGE ( 'NONE', *, *, #54731, .F. ) ; +#6246 = FILL_AREA_STYLE ('',( #36470 ) ) ; +#6247 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#6248 = CARTESIAN_POINT ( 'NONE', ( 1.364996439099779968, -1.475119686261340046, 0.8299999999999994049 ) ) ; +#6249 = EDGE_CURVE ( 'NONE', #72878, #20127, #60601, .T. ) ; +#6250 = VECTOR ( 'NONE', #84643, 1000.000000000000000 ) ; +#6252 = EDGE_CURVE ( 'NONE', #54622, #97964, #82075, .T. ) ; +#6251 = CARTESIAN_POINT ( 'NONE', ( -1.302508589717060072, -1.365949044099890264, 0.8100000000000000533 ) ) ; +#6253 = EDGE_LOOP ( 'NONE', ( #59111, #34011, #44981, #19427 ) ) ; +#6254 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#6255 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6256 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6257 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32896, 'distance_accuracy_value', 'NONE'); +#6258 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50396 ) ) ; +#6260 = FILL_AREA_STYLE_COLOUR ( '', #99870 ) ; +#6259 = STYLED_ITEM ( 'NONE', ( #9103 ), #91689 ) ; +#6261 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#6262 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #2196, #49166, #97089, #2700 ), + ( #58867, #18990, #80312, #82321 ), + ( #97582, #96085, #13663, #26191 ), + ( #58361, #96588, #64478, #89471 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#6263 = ORIENTED_EDGE ( 'NONE', *, *, #24612, .T. ) ; +#6264 = VECTOR ( 'NONE', #77510, 1000.000000000000000 ) ; +#6265 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#6266 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6267 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24687 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6322, #58177, #76321 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6269 = ORIENTED_EDGE ( 'NONE', *, *, #34619, .F. ) ; +#6270 = SURFACE_STYLE_USAGE ( .BOTH. , #99651 ) ; +#6271 = ADVANCED_FACE ( 'NONE', ( #43245 ), #75392, .F. ) ; +#6272 = VECTOR ( 'NONE', #84523, 1000.000000000000114 ) ; +#6273 = STYLED_ITEM ( 'NONE', ( #63555 ), #1198 ) ; +#6274 = ORIENTED_EDGE ( 'NONE', *, *, #74538, .T. ) ; +#6276 = ORIENTED_EDGE ( 'NONE', *, *, #46439, .F. ) ; +#6275 = LINE ( 'NONE', #98191, #26525 ) ; +#6277 = STYLED_ITEM ( 'NONE', ( #94686 ), #42176 ) ; +#6278 = SURFACE_STYLE_USAGE ( .BOTH. , #83950 ) ; +#6280 = CARTESIAN_POINT ( 'NONE', ( -1.303498337670309981, -1.475020827802409951, 0.8299999999999999600 ) ) ; +#6279 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6281 = PLANE ( 'NONE', #38374 ) ; +#6282 = CARTESIAN_POINT ( 'NONE', ( -0.2761799387799139804, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#6283 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68284 ), #43952 ) ; +#6284 = EDGE_LOOP ( 'NONE', ( #81211, #50980, #100895, #15980 ) ) ; +#6285 = PLANE ( 'NONE', #68700 ) ; +#6286 = VERTEX_POINT ( 'NONE', #54952 ) ; +#6287 = ADVANCED_FACE ( 'NONE', ( #70745 ), #61607, .T. ) ; +#6288 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6289 = VERTEX_POINT ( 'NONE', #16591 ) ; +#6290 = VECTOR ( 'NONE', #5214, 1000.000000000000000 ) ; +#6292 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6291 = SURFACE_SIDE_STYLE ('',( #13966 ) ) ; +#6293 = ORIENTED_EDGE ( 'NONE', *, *, #28090, .T. ) ; +#6294 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6295 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#6297 = EDGE_CURVE ( 'NONE', #70008, #78606, #38596, .T. ) ; +#6296 = LINE ( 'NONE', #61015, #11469 ) ; +#6298 = STYLED_ITEM ( 'NONE', ( #29040 ), #44143 ) ; +#6299 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6300 = ORIENTED_EDGE ( 'NONE', *, *, #51913, .F. ) ; +#6301 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.100000000000000089, 0.1829999999999959992 ) ) ; +#6302 = ORIENTED_EDGE ( 'NONE', *, *, #42137, .F. ) ; +#6303 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#6304 = SURFACE_STYLE_FILL_AREA ( #76306 ) ; +#6305 = FACE_OUTER_BOUND ( 'NONE', #53163, .T. ) ; +#6306 = STYLED_ITEM ( 'NONE', ( #66693 ), #32461 ) ; +#6307 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6308 = SURFACE_SIDE_STYLE ('',( #13986 ) ) ; +#6309 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#6310 = EDGE_CURVE ( 'NONE', #92966, #49449, #290, .T. ) ; +#6312 = ADVANCED_FACE ( 'NONE', ( #30399 ), #54444, .T. ) ; +#6311 = FILL_AREA_STYLE_COLOUR ( '', #63843 ) ; +#6313 = FILL_AREA_STYLE ('',( #76316 ) ) ; +#6314 = STYLED_ITEM ( 'NONE', ( #38002 ), #92883 ) ; +#6315 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6316 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6317 = ORIENTED_EDGE ( 'NONE', *, *, #98243, .T. ) ; +#6318 = FACE_OUTER_BOUND ( 'NONE', #51176, .T. ) ; +#6319 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#6321 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#6320 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6322 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6323 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6324 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8648700000000000276 ) ) ; +#6325 = VECTOR ( 'NONE', #96576, 1000.000000000000000 ) ; +#6326 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6327 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6328 = VECTOR ( 'NONE', #10448, 1000.000000000000114 ) ; +#6329 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.100000000000000089, 0.1829999999999619986 ) ) ; +#6331 = ORIENTED_EDGE ( 'NONE', *, *, #14227, .F. ) ; +#6330 = STYLED_ITEM ( 'NONE', ( #56368 ), #56309 ) ; +#6332 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6333 = EDGE_CURVE ( 'NONE', #80884, #18465, #86356, .T. ) ; +#6334 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6335 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#6336 = FACE_OUTER_BOUND ( 'NONE', #29233, .T. ) ; +#6337 = EDGE_CURVE ( 'NONE', #99161, #48586, #38111, .T. ) ; +#6338 = LINE ( 'NONE', #84014, #17036 ) ; +#6339 = CARTESIAN_POINT ( 'NONE', ( 0.01310978785461489916, -1.357122040133029950, 0.8299999999999999600 ) ) ; +#6340 = SURFACE_STYLE_FILL_AREA ( #74848 ) ; +#6341 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42286 ), #91236 ) ; +#6342 = LINE ( 'NONE', #45174, #25353 ) ; +#6343 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6344 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6345 = FILL_AREA_STYLE ('',( #12477 ) ) ; +#6346 = SURFACE_STYLE_FILL_AREA ( #98751 ) ; +#6347 = SURFACE_STYLE_FILL_AREA ( #61062 ) ; +#6348 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6349 = VECTOR ( 'NONE', #17447, 1000.000000000000000 ) ; +#6350 = SURFACE_SIDE_STYLE ('',( #86028 ) ) ; +#6351 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#6352 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6353 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6354 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#6355 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85282, 'distance_accuracy_value', 'NONE'); +#6356 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.000000000000000000 ) ) ; +#6357 = EDGE_CURVE ( 'NONE', #100002, #58491, #61964, .T. ) ; +#6358 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000000666, 3.123820061220065281, 0.000000000000000000 ) ) ; +#6359 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8648700000000000276 ) ) ; +#6360 = VECTOR ( 'NONE', #23990, 1000.000000000000000 ) ; +#6361 = PRESENTATION_STYLE_ASSIGNMENT (( #28409 ) ) ; +#6362 = PRESENTATION_STYLE_ASSIGNMENT (( #36592 ) ) ; +#6363 = ORIENTED_EDGE ( 'NONE', *, *, #11971, .T. ) ; +#6364 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#6365 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6366 = ADVANCED_FACE ( 'NONE', ( #64606 ), #25823, .T. ) ; +#6367 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87535, 'distance_accuracy_value', 'NONE'); +#6368 = PLANE ( 'NONE', #54308 ) ; +#6369 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6370 = AXIS2_PLACEMENT_3D ( 'NONE', #86903, #16918, #17923 ) ; +#6371 = CARTESIAN_POINT ( 'NONE', ( -0.01942805220116449946, -1.009819306370540071, 0.8300000000000002931 ) ) ; +#6372 = CIRCLE ( 'NONE', #1569, 0.1679250012421869831 ) ; +#6374 = EDGE_CURVE ( 'NONE', #78342, #70194, #9882, .T. ) ; +#6373 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6375 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6376 = ADVANCED_FACE ( 'NONE', ( #88095 ), #64113, .F. ) ; +#6377 = ORIENTED_EDGE ( 'NONE', *, *, #50225, .F. ) ; +#6378 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#6379 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100191, 'distance_accuracy_value', 'NONE'); +#6380 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#6381 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6382 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6383 = ORIENTED_EDGE ( 'NONE', *, *, #100125, .T. ) ; +#6384 = ORIENTED_EDGE ( 'NONE', *, *, #56364, .T. ) ; +#6385 = PRESENTATION_STYLE_ASSIGNMENT (( #27958 ) ) ; +#6386 = VECTOR ( 'NONE', #97202, 1000.000000000000000 ) ; +#6387 = ORIENTED_EDGE ( 'NONE', *, *, #33447, .T. ) ; +#6388 = CARTESIAN_POINT ( 'NONE', ( 0.08473270080998969445, -1.389761831846570095, 0.8100000000000000533 ) ) ; +#6389 = CARTESIAN_POINT ( 'NONE', ( 0.4793384683631900511, -1.221234985172420018, 0.8100000000000000533 ) ) ; +#6390 = PRESENTATION_STYLE_ASSIGNMENT (( #77393 ) ) ; +#6391 = CARTESIAN_POINT ( 'NONE', ( 3.999024875125043899, 5.267127124874957822, 0.8991599999999999593 ) ) ; +#6392 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6393 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15578 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93831, #39765, #76540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6394 = VECTOR ( 'NONE', #34395, 1000.000000000000114 ) ; +#6395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 4.591774807899559894E-33 ) ) ; +#6397 = ORIENTED_EDGE ( 'NONE', *, *, #74909, .T. ) ; +#6396 = ADVANCED_FACE ( 'NONE', ( #26833 ), #57994, .T. ) ; +#6398 = STYLED_ITEM ( 'NONE', ( #44023 ), #57176 ) ; +#6399 = VERTEX_POINT ( 'NONE', #75287 ) ; +#6400 = SURFACE_STYLE_FILL_AREA ( #27971 ) ; +#6402 = FACE_OUTER_BOUND ( 'NONE', #37503, .T. ) ; +#6401 = CIRCLE ( 'NONE', #86346, 0.6499999999789451977 ) ; +#6403 = CIRCLE ( 'NONE', #43928, 0.2000000000000000944 ) ; +#6404 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6406 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.000000000000000000 ) ) ; +#6405 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#6407 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#6408 = VECTOR ( 'NONE', #76112, 1000.000000000000000 ) ; +#6409 = EDGE_CURVE ( 'NONE', #4673, #93343, #90601, .T. ) ; +#6410 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6411 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6412 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#6413 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45562 ), #78284 ) ; +#6414 = ORIENTED_EDGE ( 'NONE', *, *, #36226, .F. ) ; +#6415 = EDGE_CURVE ( 'NONE', #48342, #93554, #67104, .T. ) ; +#6417 = LINE ( 'NONE', #37138, #72972 ) ; +#6416 = LINE ( 'NONE', #45735, #47043 ) ; +#6418 = ORIENTED_EDGE ( 'NONE', *, *, #92390, .F. ) ; +#6419 = EDGE_LOOP ( 'NONE', ( #54992, #66627, #53341, #6498, #37403 ) ) ; +#6421 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#6420 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#6422 = EDGE_CURVE ( 'NONE', #39851, #18075, #4329, .T. ) ; +#6424 = EDGE_LOOP ( 'NONE', ( #33756, #21423, #55205, #90196 ) ) ; +#6423 = SURFACE_SIDE_STYLE ('',( #22822 ) ) ; +#6425 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68440 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69133, #92632, #12980 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6427 = FACE_OUTER_BOUND ( 'NONE', #20503, .T. ) ; +#6428 = PLANE ( 'NONE', #27164 ) ; +#6429 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6430 = EDGE_LOOP ( 'NONE', ( #100624, #48962, #46924, #95417 ) ) ; +#6431 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#6432 = EDGE_LOOP ( 'NONE', ( #38729, #9544, #7368, #68516 ) ) ; +#6433 = ORIENTED_EDGE ( 'NONE', *, *, #93103, .F. ) ; +#6434 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6436 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#6435 = CARTESIAN_POINT ( 'NONE', ( 0.9629666814316270029, -1.351356007592229957, 0.8299999999999999600 ) ) ; +#6437 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6438 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.449999999999999956, -13.35000000000000142 ) ) ; +#6439 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, -0.3000000000000001554, 0.000000000000000000 ) ) ; +#6440 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61985 ), #24466 ) ; +#6441 = VECTOR ( 'NONE', #40330, 1000.000000000000000 ) ; +#6443 = EDGE_CURVE ( 'NONE', #43280, #77078, #51808, .T. ) ; +#6442 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32619 ) ) ; +#6444 = ORIENTED_EDGE ( 'NONE', *, *, #46500, .F. ) ; +#6445 = VERTEX_POINT ( 'NONE', #5282 ) ; +#6446 = FACE_OUTER_BOUND ( 'NONE', #84270, .T. ) ; +#6447 = LINE ( 'NONE', #59685, #90510 ) ; +#6448 = VECTOR ( 'NONE', #4315, 1000.000000000000000 ) ; +#6449 = CARTESIAN_POINT ( 'NONE', ( 1.063574105442089968, -1.082231071007949907, 0.8100000000000000533 ) ) ; +#6450 = CARTESIAN_POINT ( 'NONE', ( 9.408391124875011613, 2.983172875124988188, 0.8991599999999999593 ) ) ; +#6451 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#6452 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 0.6914213562373290323 ) ) ; +#6453 = SURFACE_SIDE_STYLE ('',( #45285 ) ) ; +#6454 = ORIENTED_EDGE ( 'NONE', *, *, #80631, .F. ) ; +#6455 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6456 = EDGE_CURVE ( 'NONE', #82073, #95742, #36495, .T. ) ; +#6457 = SURFACE_SIDE_STYLE ('',( #45289 ) ) ; +#6458 = SURFACE_SIDE_STYLE ('',( #5961 ) ) ; +#6459 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6460 = SURFACE_STYLE_USAGE ( .BOTH. , #91772 ) ; +#6461 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#6462 = ADVANCED_FACE ( 'NONE', ( #11894 ), #12907, .F. ) ; +#6463 = CARTESIAN_POINT ( 'NONE', ( 1.859836464378280096, -1.220010286732279958, 0.8299999999999999600 ) ) ; +#6464 = FILL_AREA_STYLE ('',( #100338 ) ) ; +#6465 = STYLED_ITEM ( 'NONE', ( #93380 ), #95044 ) ; +#6466 = SURFACE_SIDE_STYLE ('',( #76470 ) ) ; +#6467 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#6468 = SURFACE_SIDE_STYLE ('',( #76472 ) ) ; +#6469 = VECTOR ( 'NONE', #57206, 1000.000000000000000 ) ; +#6470 = AXIS2_PLACEMENT_3D ( 'NONE', #54756, #85861, #15381 ) ; +#6471 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1557, 'distance_accuracy_value', 'NONE'); +#6472 = AXIS2_PLACEMENT_3D ( 'NONE', #47477, #38823, #78619 ) ; +#6473 = FILL_AREA_STYLE ('',( #53520 ) ) ; +#6474 = SURFACE_STYLE_FILL_AREA ( #59211 ) ; +#6475 = CARTESIAN_POINT ( 'NONE', ( -0.9800485932806816125, -0.9510299480961719176, 0.8100000000000241451 ) ) ; +#6476 = ORIENTED_EDGE ( 'NONE', *, *, #53035, .F. ) ; +#6477 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23885 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23952, #7501, #7999 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6479 = FILL_AREA_STYLE ('',( #82173 ) ) ; +#6480 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#6481 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#6482 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31883, 'distance_accuracy_value', 'NONE'); +#6483 = STYLED_ITEM ( 'NONE', ( #66805 ), #80831 ) ; +#6484 = PRESENTATION_STYLE_ASSIGNMENT (( #76488 ) ) ; +#6485 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6486 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#6487 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#6488 = VERTEX_POINT ( 'NONE', #35000 ) ; +#6489 = AXIS2_PLACEMENT_3D ( 'NONE', #85506, #22222, #75344 ) ; +#6490 = EDGE_CURVE ( 'NONE', #45624, #61665, #73778, .T. ) ; +#6491 = VECTOR ( 'NONE', #71912, 1000.000000000000000 ) ; +#6492 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000533, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#6493 = VECTOR ( 'NONE', #67532, 1000.000000000000000 ) ; +#6494 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40215, 'distance_accuracy_value', 'NONE'); +#6495 = SURFACE_SIDE_STYLE ('',( #53041 ) ) ; +#6496 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5867, 'distance_accuracy_value', 'NONE'); +#6497 = ADVANCED_FACE ( 'NONE', ( #66118 ), #51315, .T. ) ; +#6498 = ORIENTED_EDGE ( 'NONE', *, *, #90316, .T. ) ; +#6499 = ORIENTED_EDGE ( 'NONE', *, *, #7889, .T. ) ; +#6500 = STYLED_ITEM ( 'NONE', ( #74034 ), #10728 ) ; +#6501 = ORIENTED_EDGE ( 'NONE', *, *, #32776, .T. ) ; +#6503 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#6502 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27682 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16171, #25409, #9477 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6504 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6505 = PRESENTATION_STYLE_ASSIGNMENT (( #14693 ) ) ; +#6506 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29463 ) ) ; +#6507 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#6508 = PRODUCT_CONTEXT ( 'NONE', #18158, 'mechanical' ) ; +#6509 = LINE ( 'NONE', #93804, #19864 ) ; +#6510 = LINE ( 'NONE', #32085, #53921 ) ; +#6513 = ORIENTED_EDGE ( 'NONE', *, *, #63272, .F. ) ; +#6512 = ORIENTED_EDGE ( 'NONE', *, *, #51870, .T. ) ; +#6511 = EDGE_CURVE ( 'NONE', #70050, #56861, #37983, .T. ) ; +#6514 = AXIS2_PLACEMENT_3D ( 'NONE', #72619, #3182, #88445 ) ; +#6515 = ORIENTED_EDGE ( 'NONE', *, *, #62023, .T. ) ; +#6516 = FILL_AREA_STYLE_COLOUR ( '', #81752 ) ; +#6517 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#6518 = ORIENTED_EDGE ( 'NONE', *, *, #82482, .F. ) ; +#6520 = EDGE_CURVE ( 'NONE', #65363, #75028, #70107, .T. ) ; +#6519 = ORIENTED_EDGE ( 'NONE', *, *, #999, .F. ) ; +#6521 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#6522 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#6523 = STYLED_ITEM ( 'NONE', ( #98223 ), #18119 ) ; +#6525 = FILL_AREA_STYLE_COLOUR ( '', #12270 ) ; +#6524 = FILL_AREA_STYLE ('',( #43390 ) ) ; +#6526 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4808578643762689842, -0.2399999999999999356 ) ) ; +#6527 = EDGE_LOOP ( 'NONE', ( #32739, #37881, #46998, #44810 ) ) ; +#6528 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6529 = ORIENTED_EDGE ( 'NONE', *, *, #24450, .T. ) ; +#6530 = VERTEX_POINT ( 'NONE', #13936 ) ; +#6531 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#6532 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50658 ) ) ; +#6533 = VECTOR ( 'NONE', #75347, 1000.000000000000000 ) ; +#6534 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6535 = EDGE_CURVE ( 'NONE', #54575, #68717, #85945, .T. ) ; +#6536 = VECTOR ( 'NONE', #17148, 1000.000000000000000 ) ; +#6539 = ORIENTED_EDGE ( 'NONE', *, *, #38186, .F. ) ; +#6538 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63031, 'distance_accuracy_value', 'NONE'); +#6537 = FACE_OUTER_BOUND ( 'NONE', #90562, .T. ) ; +#6540 = VECTOR ( 'NONE', #10245, 1000.000000000000000 ) ; +#6541 = SURFACE_SIDE_STYLE ('',( #23443 ) ) ; +#6542 = STYLED_ITEM ( 'NONE', ( #97526 ), #94289 ) ; +#6543 = CARTESIAN_POINT ( 'NONE', ( 11.10544749950005361, 4.680228500499951316, 0.8991599999999999593 ) ) ; +#6544 = ORIENTED_EDGE ( 'NONE', *, *, #49157, .T. ) ; +#6545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53539 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9635, #40380, #25570 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6546 = CARTESIAN_POINT ( 'NONE', ( 0.01061219417860849966, -1.294636995308309890, 0.8100000000000000533 ) ) ; +#6547 = VERTEX_POINT ( 'NONE', #22662 ) ; +#6548 = ADVANCED_FACE ( 'N', ( #23673 ), #14943, .T. ) ; +#6549 = EDGE_LOOP ( 'NONE', ( #93227, #64631, #46207, #7499 ) ) ; +#6550 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#6551 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6552 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000004441, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#6553 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#6554 = VECTOR ( 'NONE', #25900, 1000.000000000000000 ) ; +#6555 = PRESENTATION_STYLE_ASSIGNMENT (( #100424 ) ) ; +#6556 = EDGE_CURVE ( 'NONE', #5088, #58647, #45009, .T. ) ; +#6558 = EDGE_CURVE ( 'NONE', #79924, #10525, #22147, .T. ) ; +#6557 = SURFACE_STYLE_USAGE ( .BOTH. , #60286 ) ; +#6559 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#6560 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6561 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6562 = ORIENTED_EDGE ( 'NONE', *, *, #60585, .F. ) ; +#6563 = CARTESIAN_POINT ( 'NONE', ( -0.9443983742018540184, -1.435626150595060047, 0.8100000000000000533 ) ) ; +#6564 = ORIENTED_EDGE ( 'NONE', *, *, #85076, .F. ) ; +#6565 = EDGE_CURVE ( 'NONE', #34794, #4908, #85438, .T. ) ; +#6566 = EDGE_CURVE ( 'NONE', #18482, #75075, #14661, .T. ) ; +#6568 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55483, 'distance_accuracy_value', 'NONE'); +#6567 = SURFACE_SIDE_STYLE ('',( #67884 ) ) ; +#6569 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6570 = SURFACE_STYLE_FILL_AREA ( #76571 ) ; +#6571 = SURFACE_SIDE_STYLE ('',( #76572 ) ) ; +#6572 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6573 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.500000000000000000, 9.346759736271676912E-79 ) ) ; +#6574 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6575 = LINE ( 'NONE', #53123, #396 ) ; +#6576 = ADVANCED_FACE ( 'NONE', ( #63000 ), #63503, .T. ) ; +#6577 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5238200612200850648, 0.000000000000000000 ) ) ; +#6578 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.299999999999999822, 0.8299999999999999600 ) ) ; +#6579 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6580 = FILL_AREA_STYLE ('',( #54120 ) ) ; +#6581 = VECTOR ( 'NONE', #14354, 1000.000000000000000 ) ; +#6582 = EDGE_CURVE ( 'NONE', #46152, #36115, #24711, .T. ) ; +#6584 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#6583 = LINE ( 'NONE', #30605, #83167 ) ; +#6586 = VECTOR ( 'NONE', #37360, 1000.000000000000000 ) ; +#6585 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6587 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77339, 'distance_accuracy_value', 'NONE'); +#6588 = ORIENTED_EDGE ( 'NONE', *, *, #87961, .T. ) ; +#6589 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6590 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#6591 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#6592 = FILL_AREA_STYLE_COLOUR ( '', #94108 ) ; +#6593 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#6594 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4424 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10818, #26749, #50748 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6595 = PRESENTATION_STYLE_ASSIGNMENT (( #86797 ) ) ; +#6596 = PRESENTATION_STYLE_ASSIGNMENT (( #61822 ) ) ; +#6597 = CARTESIAN_POINT ( 'NONE', ( 0.1833333333333339865, 3.099999999999980549, 0.000000000000000000 ) ) ; +#6598 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0201_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0201_20210301.STEP', '', ( #57614 ) ) ; +#6599 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57289 ) ) ; +#6600 = SURFACE_STYLE_USAGE ( .BOTH. , #98504 ) ; +#6601 = ORIENTED_EDGE ( 'NONE', *, *, #55652, .T. ) ; +#6602 = PRESENTATION_STYLE_ASSIGNMENT (( #23517 ) ) ; +#6603 = VERTEX_POINT ( 'NONE', #95589 ) ; +#6604 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#6605 = VECTOR ( 'NONE', #96515, 1000.000000000000000 ) ; +#6606 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#6607 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96232 ), #31095 ) ; +#6608 = SURFACE_STYLE_USAGE ( .BOTH. , #37831 ) ; +#6609 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9809 ), #27854 ) ; +#6610 = CARTESIAN_POINT ( 'NONE', ( -0.2409735724455049910, -1.328064047174219997, 0.8299999999999995159 ) ) ; +#6611 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6613 = CARTESIAN_POINT ( 'NONE', ( -0.1669357969068207548, -0.9052759646745555111, 0.8100000000003876321 ) ) ; +#6614 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6615 = ADVANCED_FACE ( 'NONE', ( #2208 ), #33359, .T. ) ; +#6616 = ORIENTED_EDGE ( 'NONE', *, *, #41316, .T. ) ; +#6617 = SURFACE_STYLE_USAGE ( .BOTH. , #76624 ) ; +#6618 = ORIENTED_EDGE ( 'NONE', *, *, #1360, .T. ) ; +#6619 = PRESENTATION_STYLE_ASSIGNMENT (( #53665 ) ) ; +#6620 = VECTOR ( 'NONE', #61940, 1000.000000000000000 ) ; +#6621 = ORIENTED_EDGE ( 'NONE', *, *, #83188, .T. ) ; +#6622 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#6623 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#6624 = LINE ( 'NONE', #68948, #11943 ) ; +#6625 = AXIS2_PLACEMENT_3D ( 'NONE', #92022, #52748, #100081 ) ; +#6626 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6627 = LINE ( 'NONE', #45958, #241 ) ; +#6628 = CARTESIAN_POINT ( 'NONE', ( 9.076051124874956244, 8.958224875125043951, 0.8991599999999999593 ) ) ; +#6630 = VERTEX_POINT ( 'NONE', #25695 ) ; +#6629 = ORIENTED_EDGE ( 'NONE', *, *, #40541, .T. ) ; +#6631 = ORIENTED_EDGE ( 'NONE', *, *, #10433, .F. ) ; +#6633 = CARTESIAN_POINT ( 'NONE', ( -0.4939768715539690214, -0.9855649010623360740, 0.8100000000000000533 ) ) ; +#6632 = SURFACE_STYLE_FILL_AREA ( #60370 ) ; +#6634 = VERTEX_POINT ( 'NONE', #32340 ) ; +#6636 = EDGE_CURVE ( 'NONE', #89436, #88958, #69420, .T. ) ; +#6635 = ORIENTED_EDGE ( 'NONE', *, *, #5676, .F. ) ; +#6637 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#6638 = CARTESIAN_POINT ( 'NONE', ( -0.4842236312130879794, -1.167783801559209911, 0.8100000000000000533 ) ) ; +#6639 = LINE ( 'NONE', #37866, #6182 ) ; +#6640 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80797 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4883, #98259, #44195 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6641 = PLANE ( 'NONE', #7590 ) ; +#6642 = LINE ( 'NONE', #1069, #62623 ) ; +#6643 = ORIENTED_EDGE ( 'NONE', *, *, #64984, .F. ) ; +#6644 = ORIENTED_EDGE ( 'NONE', *, *, #79603, .F. ) ; +#6645 = SURFACE_STYLE_USAGE ( .BOTH. , #76662 ) ; +#6646 = EDGE_LOOP ( 'NONE', ( #62743, #16084, #91587, #97112 ) ) ; +#6647 = AXIS2_PLACEMENT_3D ( 'NONE', #47017, #78656, #40390 ) ; +#6648 = FILL_AREA_STYLE_COLOUR ( '', #297 ) ; +#6649 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6650 = VERTEX_POINT ( 'NONE', #69327 ) ; +#6651 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#6652 = ORIENTED_EDGE ( 'NONE', *, *, #37774, .T. ) ; +#6653 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, 3.099999999999995204, -0.02000000000000000042 ) ) ; +#6654 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#6655 = VERTEX_POINT ( 'NONE', #53566 ) ; +#6656 = SURFACE_STYLE_USAGE ( .BOTH. , #76677 ) ; +#6657 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#6658 = VECTOR ( 'NONE', #23719, 1000.000000000000000 ) ; +#6659 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47475 ) ) ; +#6661 = ORIENTED_EDGE ( 'NONE', *, *, #59640, .T. ) ; +#6660 = LINE ( 'NONE', #85339, #86855 ) ; +#6662 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64598 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71045, #1098, #33656 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6663 = SURFACE_STYLE_FILL_AREA ( #100546 ) ; +#6664 = DIRECTION ( 'NONE', ( -0.7071067806865475314, -0.7071067816865476141, -0.000000000000000000 ) ) ; +#6665 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54658 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64814, #51031, #82169 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6666 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6667 = LINE ( 'NONE', #8663, #74993 ) ; +#6668 = EDGE_LOOP ( 'NONE', ( #26220, #87114, #48418, #96501 ) ) ; +#6669 = STYLED_ITEM ( 'NONE', ( #56136 ), #58638 ) ; +#6670 = FILL_AREA_STYLE ('',( #45023 ) ) ; +#6671 = EDGE_CURVE ( 'NONE', #23833, #48771, #88981, .T. ) ; +#6672 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6673 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8991599999999999593 ) ) ; +#6675 = CARTESIAN_POINT ( 'NONE', ( 1.599803260885759970, -1.408946430034399899, 0.8299999999999999600 ) ) ; +#6674 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#6676 = PRESENTATION_STYLE_ASSIGNMENT (( #48090 ) ) ; +#6677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6678 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13175 ) ) ; +#6679 = ORIENTED_EDGE ( 'NONE', *, *, #82923, .F. ) ; +#6680 = FILL_AREA_STYLE_COLOUR ( '', #77527 ) ; +#6681 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#6682 = EDGE_CURVE ( 'NONE', #36383, #92147, #59382, .T. ) ; +#6683 = EDGE_LOOP ( 'NONE', ( #11872, #58137, #97382, #83174 ) ) ; +#6685 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6684 = PRESENTATION_STYLE_ASSIGNMENT (( #8190 ) ) ; +#6686 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57390 ), #96470 ) ; +#6687 = VERTEX_POINT ( 'NONE', #21905 ) ; +#6688 = SURFACE_STYLE_USAGE ( .BOTH. , #98610 ) ; +#6689 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#6690 = CARTESIAN_POINT ( 'NONE', ( -0.02181523387524260046, -1.116141175150469955, 0.8300000000000005151 ) ) ; +#6691 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.000000000000000000 ) ) ; +#6692 = SURFACE_SIDE_STYLE ('',( #68545 ) ) ; +#6693 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6694 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6695 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94806 ) ) ; +#6696 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.000000000000000000 ) ) ; +#6697 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6698 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 1.050000000000000044 ) ) ; +#6699 = STYLED_ITEM ( 'NONE', ( #3219 ), #46508 ) ; +#6700 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#6701 = FILL_AREA_STYLE_COLOUR ( '', #74665 ) ; +#6702 = SURFACE_STYLE_USAGE ( .BOTH. , #45541 ) ; +#6703 = VERTEX_POINT ( 'NONE', #65999 ) ; +#6704 = PRESENTATION_STYLE_ASSIGNMENT (( #29760 ) ) ; +#6705 = VERTEX_POINT ( 'NONE', #42522 ) ; +#6706 = VECTOR ( 'NONE', #95580, 1000.000000000000000 ) ; +#6707 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#6708 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#6709 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#6710 = PLANE ( 'NONE', #29757 ) ; +#6711 = CYLINDRICAL_SURFACE ( 'NONE', #23255, 0.01000000000000002623 ) ; +#6712 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#6713 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8648700000000000276 ) ) ; +#6714 = LINE ( 'NONE', #46597, #68880 ) ; +#6715 = ADVANCED_FACE ( 'NONE', ( #27717 ), #6996, .F. ) ; +#6716 = EDGE_LOOP ( 'NONE', ( #53649, #2727, #20951, #32371 ) ) ; +#6717 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#6718 = PRESENTATION_STYLE_ASSIGNMENT (( #52296 ) ) ; +#6719 = SURFACE_SIDE_STYLE ('',( #29298 ) ) ; +#6720 = FILL_AREA_STYLE ('',( #16962 ) ) ; +#6721 = VECTOR ( 'NONE', #93491, 999.9999999999998863 ) ; +#6722 = VECTOR ( 'NONE', #6014, 1000.000000000000000 ) ; +#6723 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6724 = ORIENTED_EDGE ( 'NONE', *, *, #86361, .T. ) ; +#6725 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, 0.000000000000000000 ) ) ; +#6726 = VECTOR ( 'NONE', #74461, 999.9999999999998863 ) ; +#6727 = SURFACE_STYLE_FILL_AREA ( #76757 ) ; +#6728 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52526 ) ) ; +#6729 = PRESENTATION_STYLE_ASSIGNMENT (( #94582 ) ) ; +#6730 = ORIENTED_EDGE ( 'NONE', *, *, #73450, .F. ) ; +#6731 = VECTOR ( 'NONE', #98802, 1000.000000000000000 ) ; +#6732 = CARTESIAN_POINT ( 'NONE', ( 5.971852916749958773, 6.264148083250120180, 0.8991599999999999593 ) ) ; +#6733 = PRESENTATION_STYLE_ASSIGNMENT (( #45576 ) ) ; +#6734 = SURFACE_STYLE_USAGE ( .BOTH. , #68592 ) ; +#6735 = PRESENTATION_STYLE_ASSIGNMENT (( #76767 ) ) ; +#6736 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41214 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16889, #24102, #56772 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6738 = EDGE_CURVE ( 'NONE', #11057, #59694, #41451, .T. ) ; +#6737 = ORIENTED_EDGE ( 'NONE', *, *, #43739, .F. ) ; +#6739 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#6740 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6741 = VECTOR ( 'NONE', #40350, 1000.000000000000000 ) ; +#6742 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.7000000000000018430, -1.195472123049164304E-89 ) ) ; +#6743 = ORIENTED_EDGE ( 'NONE', *, *, #30721, .T. ) ; +#6744 = ORIENTED_EDGE ( 'NONE', *, *, #79611, .F. ) ; +#6745 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18672, 'distance_accuracy_value', 'NONE'); +#6746 = AXIS2_PLACEMENT_3D ( 'NONE', #43022, #35410, #28225 ) ; +#6747 = ORIENTED_EDGE ( 'NONE', *, *, #11486, .T. ) ; +#6749 = ORIENTED_EDGE ( 'NONE', *, *, #36604, .F. ) ; +#6748 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6750 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37761, 'distance_accuracy_value', 'NONE'); +#6751 = CARTESIAN_POINT ( 'NONE', ( 8.383086875125043136, 2.877106875125044372, 0.8648700000000000276 ) ) ; +#6752 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6753 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#6754 = FILL_AREA_STYLE_COLOUR ( '', #6323 ) ; +#6755 = VECTOR ( 'NONE', #5263, 1000.000000000000000 ) ; +#6756 = ORIENTED_EDGE ( 'NONE', *, *, #31853, .T. ) ; +#6757 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#6758 = ORIENTED_EDGE ( 'NONE', *, *, #275, .T. ) ; +#6759 = EDGE_CURVE ( 'NONE', #2685, #88220, #4691, .T. ) ; +#6760 = CARTESIAN_POINT ( 'NONE', ( 1.408848379044900012, -1.435626150595060047, 0.8100000000000000533 ) ) ; +#6761 = ADVANCED_FACE ( 'NONE', ( #28205 ), #26707, .F. ) ; +#6762 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6763 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6764 = STYLED_ITEM ( 'NONE', ( #86413 ), #52053 ) ; +#6765 = ORIENTED_EDGE ( 'NONE', *, *, #73273, .T. ) ; +#6767 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8991599999999999593 ) ) ; +#6766 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6768 = ORIENTED_EDGE ( 'NONE', *, *, #95836, .T. ) ; +#6769 = VECTOR ( 'NONE', #60876, 1000.000000000000000 ) ; +#6771 = LINE ( 'NONE', #51345, #85815 ) ; +#6770 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6772 = SURFACE_STYLE_USAGE ( .BOTH. , #14481 ) ; +#6773 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6774 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93268 ), #96561 ) ; +#6775 = STYLED_ITEM ( 'NONE', ( #49562 ), #45972 ) ; +#6776 = ADVANCED_FACE ( 'NONE', ( #77528 ), #78049, .T. ) ; +#6777 = EDGE_LOOP ( 'NONE', ( #86554, #11027, #96823, #27412 ) ) ; +#6778 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#6779 = ORIENTED_EDGE ( 'NONE', *, *, #20140, .T. ) ; +#6780 = LINE ( 'NONE', #54359, #5369 ) ; +#6781 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85073 ), #50934 ) ; +#6782 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81904 ), #31362 ) ; +#6783 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6784 = FILL_AREA_STYLE_COLOUR ( '', #80037 ) ; +#6785 = LINE ( 'NONE', #91628, #39760 ) ; +#6786 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6787 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#6788 = VECTOR ( 'NONE', #82988, 1000.000000000000000 ) ; +#6789 = FILL_AREA_STYLE ('',( #98719 ) ) ; +#6790 = EDGE_CURVE ( 'NONE', #100007, #14055, #16223, .T. ) ; +#6791 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93290 ), #80309 ) ; +#6792 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8199999999999999512 ) ) ; +#6793 = ORIENTED_EDGE ( 'NONE', *, *, #76679, .F. ) ; +#6794 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#6795 = LINE ( 'NONE', #24253, #2414 ) ; +#6798 = FILL_AREA_STYLE_COLOUR ( '', #24852 ) ; +#6797 = SURFACE_SIDE_STYLE ('',( #69121 ) ) ; +#6796 = CARTESIAN_POINT ( 'NONE', ( 6.827451124874956534, 2.438700875125043854, 0.8648700000000000276 ) ) ; +#6799 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77002 ) ) ; +#6800 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5966, 'distance_accuracy_value', 'NONE'); +#6801 = SURFACE_SIDE_STYLE ('',( #38542 ) ) ; +#6802 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9097 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21455, #10068, #40322 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6803 = VECTOR ( 'NONE', #70122, 1000.000000000000000 ) ; +#6804 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000002580, 12.86860300000000024, 0.8648700000000000276 ) ) ; +#6805 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.6999999999999990674, 0.1829999999999790128 ) ) ; +#6806 = ORIENTED_EDGE ( 'NONE', *, *, #3696, .T. ) ; +#6807 = VECTOR ( 'NONE', #40307, 1000.000000000000000 ) ; +#6808 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6809 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#6810 = SURFACE_STYLE_USAGE ( .BOTH. , #28878 ) ; +#6811 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#6812 = SURFACE_STYLE_FILL_AREA ( #92636 ) ; +#6813 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73735 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100122, #77242, #47625 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6814 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.299999999999999822, 2.243222336733894049E-79 ) ) ; +#6815 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.1499999999999999667, -0.02000000000000000042 ) ) ; +#6816 = SURFACE_STYLE_USAGE ( .BOTH. , #78374 ) ; +#6817 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6818 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#6819 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.000000000000000000 ) ) ; +#6820 = ADVANCED_FACE ( 'NONE', ( #70363 ), #83894, .F. ) ; +#6821 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#6822 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701300244, 0.7099999999999999645, 0.4397321428571430157 ) ) ; +#6823 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36308 ), #63997 ) ; +#6824 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6166666666666666963, 0.000000000000000000 ) ) ; +#6825 = FACE_OUTER_BOUND ( 'NONE', #29177, .T. ) ; +#6826 = FACE_OUTER_BOUND ( 'NONE', #2719, .T. ) ; +#6827 = LINE ( 'NONE', #61579, #27579 ) ; +#6828 = PRESENTATION_STYLE_ASSIGNMENT (( #99265 ) ) ; +#6829 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84771 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10745, #34858, #42499 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6830 = LINE ( 'NONE', #62592, #82987 ) ; +#6831 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6832 = ADVANCED_FACE ( 'NONE', ( #88235 ), #65237, .F. ) ; +#6833 = ORIENTED_EDGE ( 'NONE', *, *, #56078, .F. ) ; +#6834 = PRESENTATION_STYLE_ASSIGNMENT (( #51409 ) ) ; +#6835 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#6836 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, 1.048695503451022204E-76 ) ) ; +#6837 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76764 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88037, #10322, #78856 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6838 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6839 = FILL_AREA_STYLE_COLOUR ( '', #16013 ) ; +#6840 = VERTEX_POINT ( 'NONE', #96352 ) ; +#6841 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#6842 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53386 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59274, #7014, #52093 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6843 = FILL_AREA_STYLE_COLOUR ( '', #56554 ) ; +#6844 = CARTESIAN_POINT ( 'NONE', ( -0.5610005133853439574, 2.432921575926970004, 0.8100000000000000533 ) ) ; +#6845 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2373, #63165, #47819 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6846 = VERTEX_POINT ( 'NONE', #18755 ) ; +#6847 = LINE ( 'NONE', #69180, #78269 ) ; +#6848 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1619, 'distance_accuracy_value', 'NONE'); +#6849 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736765574E-18, 0.8199999999999998401, -0.04999999999999998890 ) ) ; +#6850 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6851 = AXIS2_PLACEMENT_3D ( 'NONE', #57050, #9949, #95777 ) ; +#6852 = AXIS2_PLACEMENT_3D ( 'NONE', #61437, #5227, #76722 ) ; +#6853 = VERTEX_POINT ( 'NONE', #2461 ) ; +#6854 = ORIENTED_EDGE ( 'NONE', *, *, #84870, .T. ) ; +#6855 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68872 ) ) ; +#6856 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75390 ), #44390 ) ; +#6857 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49228, #29615, #60797 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6858 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6859 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6860 = ORIENTED_EDGE ( 'NONE', *, *, #33195, .T. ) ; +#6861 = CARTESIAN_POINT ( 'NONE', ( 0.09335570779574380029, -1.336905478629369926, 0.8299999999999999600 ) ) ; +#6862 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000010214, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#6863 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6864 = STYLED_ITEM ( 'NONE', ( #14851 ), #60282 ) ; +#6865 = EDGE_CURVE ( 'NONE', #48127, #35608, #49426, .T. ) ; +#6866 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#6867 = EDGE_CURVE ( 'NONE', #61132, #64741, #34628, .T. ) ; +#6868 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68876 ) ) ; +#6869 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#6870 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #27452, #1878 ) ; +#6871 = VERTEX_POINT ( 'NONE', #26959 ) ; +#6872 = ORIENTED_EDGE ( 'NONE', *, *, #932, .T. ) ; +#6873 = FILL_AREA_STYLE ('',( #32852 ) ) ; +#6874 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70030, 'distance_accuracy_value', 'NONE'); +#6875 = AXIS2_PLACEMENT_3D ( 'NONE', #24479, #15218, #62760 ) ; +#6877 = CARTESIAN_POINT ( 'NONE', ( 1.367410627668359968, -0.9444486738239200596, 0.8299999999999999600 ) ) ; +#6876 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6878 = SURFACE_STYLE_USAGE ( .BOTH. , #29454 ) ; +#6879 = ADVANCED_FACE ( 'NONE', ( #58125 ), #66253, .T. ) ; +#6880 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6881 = DIRECTION ( 'NONE', ( 0.01414952675146622860, 0.9998998904353922912, 0.000000000000000000 ) ) ; +#6882 = EDGE_CURVE ( 'NONE', #30781, #21841, #52440, .T. ) ; +#6883 = PRESENTATION_STYLE_ASSIGNMENT (( #54468 ) ) ; +#6884 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39561 ) ) ; +#6885 = ORIENTED_EDGE ( 'NONE', *, *, #962, .T. ) ; +#6887 = SURFACE_STYLE_USAGE ( .BOTH. , #15612 ) ; +#6886 = SURFACE_SIDE_STYLE ('',( #37635 ) ) ; +#6888 = ORIENTED_EDGE ( 'NONE', *, *, #12428, .F. ) ; +#6889 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #29998, #54017, #45312, #90814, #22356, #68796, #38197, #36200, #21863 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000013323, 0.3750000000000011102, 0.5000000000000008882, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#6890 = ORIENTED_EDGE ( 'NONE', *, *, #76803, .F. ) ; +#6891 = CARTESIAN_POINT ( 'NONE', ( 1.363156991944870056, -1.321802795360440319, 0.8299999999999999600 ) ) ; +#6892 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.500000000000000000, 1.121611168366946904E-78 ) ) ; +#6893 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#6895 = ORIENTED_EDGE ( 'NONE', *, *, #70015, .T. ) ; +#6894 = PLANE ( 'NONE', #85149 ) ; +#6896 = FILL_AREA_STYLE ('',( #86096 ) ) ; +#6897 = PLANE ( 'NONE', #63391 ) ; +#6898 = EDGE_CURVE ( 'NONE', #13261, #98006, #61118, .T. ) ; +#6899 = LINE ( 'NONE', #16630, #98770 ) ; +#6900 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#6901 = ORIENTED_EDGE ( 'NONE', *, *, #20731, .T. ) ; +#6902 = FILL_AREA_STYLE_COLOUR ( '', #90592 ) ; +#6903 = FILL_AREA_STYLE_COLOUR ( '', #28286 ) ; +#6904 = ORIENTED_EDGE ( 'NONE', *, *, #4025, .F. ) ; +#6905 = ORIENTED_EDGE ( 'NONE', *, *, #67974, .F. ) ; +#6906 = LINE ( 'NONE', #85601, #48667 ) ; +#6907 = FILL_AREA_STYLE_COLOUR ( '', #84615 ) ; +#6908 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#6909 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62587, #16065, #92651, #37587 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#6910 = FILL_AREA_STYLE ('',( #53972 ) ) ; +#6912 = EDGE_CURVE ( 'NONE', #38122, #73676, #74422, .T. ) ; +#6911 = LINE ( 'NONE', #32002, #54641 ) ; +#6913 = VECTOR ( 'NONE', #31766, 1000.000000000000000 ) ; +#6914 = VECTOR ( 'NONE', #81613, 1000.000000000000000 ) ; +#6915 = AXIS2_PLACEMENT_3D ( 'NONE', #52046, #84170, #36718 ) ; +#6916 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6917 = SURFACE_STYLE_USAGE ( .BOTH. , #45769 ) ; +#6918 = EDGE_LOOP ( 'NONE', ( #68458, #75048, #63524, #52563 ) ) ; +#6919 = SURFACE_STYLE_USAGE ( .BOTH. , #70803 ) ; +#6920 = ORIENTED_EDGE ( 'NONE', *, *, #43047, .F. ) ; +#6921 = ADVANCED_FACE ( 'NONE', ( #99775 ), #4934, .F. ) ; +#6922 = AXIS2_PLACEMENT_3D ( 'NONE', #91140, #76815, #84969 ) ; +#6923 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6924 = CARTESIAN_POINT ( 'NONE', ( 1.060135477854049935, -1.070174563215090080, 0.8299999999999999600 ) ) ; +#6925 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#6926 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96710 ) ) ; +#6927 = VECTOR ( 'NONE', #43456, 1000.000000000000114 ) ; +#6928 = SURFACE_STYLE_FILL_AREA ( #100815 ) ; +#6929 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#6930 = STYLED_ITEM ( 'NONE', ( #11381 ), #21128 ) ; +#6931 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333316872, -2.299999999999999822, 1.747825839084584091E-76 ) ) ; +#6932 = ORIENTED_EDGE ( 'NONE', *, *, #86315, .F. ) ; +#6933 = PLANE ( 'NONE', #48930 ) ; +#6935 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#6934 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#6936 = FILL_AREA_STYLE_COLOUR ( '', #2162 ) ; +#6937 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82913 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99354, #23882, #84634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6938 = PLANE ( 'NONE', #4423 ) ; +#6939 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6940 = FACE_OUTER_BOUND ( 'NONE', #25460, .T. ) ; +#6941 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37939 ), #28186 ) ; +#6942 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#6943 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6944 = ADVANCED_FACE ( 'NONE', ( #74921 ), #36132, .F. ) ; +#6945 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6946 = PRESENTATION_STYLE_ASSIGNMENT (( #39689 ) ) ; +#6947 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#6948 = VECTOR ( 'NONE', #59785, 1000.000000000000000 ) ; +#6949 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#6950 = VECTOR ( 'NONE', #54982, 1000.000000000000000 ) ; +#6951 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.9000000000000006883, 0.1829999999999619709 ) ) ; +#6952 = SURFACE_STYLE_FILL_AREA ( #373 ) ; +#6953 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999409, 0.8991599999999999593 ) ) ; +#6954 = EDGE_CURVE ( 'NONE', #69558, #15985, #77916, .T. ) ; +#6955 = ORIENTED_EDGE ( 'NONE', *, *, #69998, .T. ) ; +#6956 = FACE_OUTER_BOUND ( 'NONE', #44751, .T. ) ; +#6957 = SURFACE_STYLE_USAGE ( .BOTH. , #15160 ) ; +#6958 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000777, 0.1399999999999999856 ) ) ; +#6959 = LINE ( 'NONE', #898, #22425 ) ; +#6960 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#6961 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22616 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69174, #93167, #55452 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6962 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#6963 = EDGE_CURVE ( 'NONE', #39755, #65881, #46228, .T. ) ; +#6964 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6965 = CARTESIAN_POINT ( 'NONE', ( 1.356239337464581807, -1.197864191688263746, 0.8099999999998652722 ) ) ; +#6966 = ORIENTED_EDGE ( 'NONE', *, *, #32796, .T. ) ; +#6967 = CIRCLE ( 'NONE', #25029, 0.05000000000000002359 ) ; +#6968 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#6969 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#6970 = FILL_AREA_STYLE ('',( #53540 ) ) ; +#6971 = VECTOR ( 'NONE', #47648, 1000.000000000000114 ) ; +#6972 = FACE_OUTER_BOUND ( 'NONE', #9259, .T. ) ; +#6973 = ORIENTED_EDGE ( 'NONE', *, *, #4872, .T. ) ; +#6974 = ORIENTED_EDGE ( 'NONE', *, *, #28988, .F. ) ; +#6975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52314 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1650, #11948, #74332 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6976 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#6977 = EDGE_LOOP ( 'NONE', ( #50491, #86373, #31373, #63143, #85051, #56658 ) ) ; +#6978 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#6979 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#6980 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7334 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19348, #67315, #18838 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#6981 = STYLED_ITEM ( 'NONE', ( #77773 ), #26027 ) ; +#6982 = PLANE ( 'NONE', #94217 ) ; +#6983 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#6984 = EDGE_CURVE ( 'NONE', #44555, #32462, #47275, .T. ) ; +#6985 = SURFACE_STYLE_USAGE ( .BOTH. , #16590 ) ; +#6986 = PLANE ( 'NONE', #7129 ) ; +#6987 = PRODUCT_CONTEXT ( 'NONE', #12897, 'mechanical' ) ; +#6988 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#6990 = EDGE_LOOP ( 'NONE', ( #71268, #83478, #4610, #16352 ) ) ; +#6989 = ORIENTED_EDGE ( 'NONE', *, *, #48219, .F. ) ; +#6991 = VECTOR ( 'NONE', #78705, 1000.000000000000000 ) ; +#6992 = ORIENTED_EDGE ( 'NONE', *, *, #35211, .F. ) ; +#6994 = STYLED_ITEM ( 'NONE', ( #95414 ), #19791 ) ; +#6993 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89533, 'distance_accuracy_value', 'NONE'); +#6995 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#6996 = PLANE ( 'NONE', #34354 ) ; +#6998 = FACE_OUTER_BOUND ( 'NONE', #91722, .T. ) ; +#6997 = FILL_AREA_STYLE_COLOUR ( '', #14686 ) ; +#6999 = VERTEX_POINT ( 'NONE', #71263 ) ; +#7000 = VECTOR ( 'NONE', #1395, 1000.000000000000000 ) ; +#7001 = ORIENTED_EDGE ( 'NONE', *, *, #75641, .T. ) ; +#7002 = FILL_AREA_STYLE ('',( #60737 ) ) ; +#7003 = EDGE_CURVE ( 'NONE', #52485, #87763, #38127, .T. ) ; +#7004 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61453 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95087, #54829, #672 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7005 = AXIS2_PLACEMENT_3D ( 'NONE', #8952, #96292, #9469 ) ; +#7006 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7007 = LINE ( 'NONE', #2847, #46583 ) ; +#7008 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#7009 = ORIENTED_EDGE ( 'NONE', *, *, #77523, .F. ) ; +#7010 = CARTESIAN_POINT ( 'NONE', ( -0.5440898474478359503, -0.9715902597976999733, 0.8099999999999990541 ) ) ; +#7011 = STYLED_ITEM ( 'NONE', ( #17286 ), #60713 ) ; +#7012 = ORIENTED_EDGE ( 'NONE', *, *, #13271, .T. ) ; +#7013 = ORIENTED_EDGE ( 'NONE', *, *, #76273, .T. ) ; +#7014 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90191 ), #39686 ) ; +#7016 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7017 = SURFACE_STYLE_FILL_AREA ( #61762 ) ; +#7019 = ORIENTED_EDGE ( 'NONE', *, *, #91293, .T. ) ; +#7018 = PLANE ( 'NONE', #80452 ) ; +#7020 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7021 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #612 ) ) ; +#7022 = FILL_AREA_STYLE_COLOUR ( '', #75966 ) ; +#7023 = CYLINDRICAL_SURFACE ( 'NONE', #31023, 0.1679250012421869831 ) ; +#7024 = ORIENTED_EDGE ( 'NONE', *, *, #37206, .T. ) ; +#7025 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7026 = SURFACE_STYLE_FILL_AREA ( #84716 ) ; +#7027 = VERTEX_POINT ( 'NONE', #93192 ) ; +#7028 = VERTEX_POINT ( 'NONE', #31460 ) ; +#7029 = CYLINDRICAL_SURFACE ( 'NONE', #35890, 0.05000000000000012768 ) ; +#7030 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7031 = STYLED_ITEM ( 'NONE', ( #34362 ), #67477 ) ; +#7032 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7033 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.500000000000000000, 0.1829999999999999960 ) ) ; +#7034 = FILL_AREA_STYLE_COLOUR ( '', #67172 ) ; +#7035 = CARTESIAN_POINT ( 'NONE', ( 1.360085058678500047, -1.308270162923429902, 0.8299999999999997380 ) ) ; +#7036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62095, 'distance_accuracy_value', 'NONE'); +#7037 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7038 = ORIENTED_EDGE ( 'NONE', *, *, #36, .T. ) ; +#7039 = CARTESIAN_POINT ( 'NONE', ( 0.4292069872566470767, -1.170408502478720081, 0.8299999999999999600 ) ) ; +#7040 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000400, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#7041 = ORIENTED_EDGE ( 'NONE', *, *, #83082, .T. ) ; +#7042 = EDGE_CURVE ( 'NONE', #1626, #28082, #62114, .T. ) ; +#7043 = VECTOR ( 'NONE', #78701, 1000.000000000000000 ) ; +#7044 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 1.306104834246980087E-31 ) ) ; +#7045 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#7046 = CARTESIAN_POINT ( 'NONE', ( -0.4373985389610389185, 0.6899999999999999467, -1.084202172485504434E-16 ) ) ; +#7047 = SURFACE_STYLE_FILL_AREA ( #15778 ) ; +#7048 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69045 ), #20170 ) ; +#7049 = CARTESIAN_POINT ( 'NONE', ( 1.745101982296789922, -0.9718760589866800581, 0.8100000000000000533 ) ) ; +#7050 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7051 = DIRECTION ( 'NONE', ( 0.7071067811865395791, 0.7071067811865554553, 0.000000000000000000 ) ) ; +#7052 = PLANE ( 'NONE', #78604 ) ; +#7053 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7054 = CARTESIAN_POINT ( 'NONE', ( 5.929425999999999419, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#7055 = FACE_OUTER_BOUND ( 'NONE', #54816, .T. ) ; +#7056 = AXIS2_PLACEMENT_3D ( 'NONE', #8224, #16432, #70588 ) ; +#7057 = PLANE ( 'NONE', #74421 ) ; +#7058 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #54348, #76808, #31347, #52350 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7060 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7059 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7061 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#7062 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#7063 = FILL_AREA_STYLE_COLOUR ( '', #87617 ) ; +#7064 = FILL_AREA_STYLE_COLOUR ( '', #78802 ) ; +#7065 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9061 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53516, #14147, #59206 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7067 = VERTEX_POINT ( 'NONE', #77406 ) ; +#7066 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26803 ), #85432 ) ; +#7068 = SURFACE_SIDE_STYLE ('',( #85759 ) ) ; +#7069 = EDGE_CURVE ( 'NONE', #100135, #61605, #62628, .T. ) ; +#7070 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78783, 'distance_accuracy_value', 'NONE'); +#7071 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54097, 'distance_accuracy_value', 'NONE'); +#7072 = LINE ( 'NONE', #29154, #21663 ) ; +#7073 = SURFACE_STYLE_FILL_AREA ( #93399 ) ; +#7074 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85364 ) ) ; +#7075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7076 = SURFACE_SIDE_STYLE ('',( #55677 ) ) ; +#7077 = LINE ( 'NONE', #30127, #34574 ) ; +#7078 = FILL_AREA_STYLE ('',( #8579 ) ) ; +#7079 = VECTOR ( 'NONE', #35049, 1000.000000000000000 ) ; +#7080 = ORIENTED_EDGE ( 'NONE', *, *, #85534, .T. ) ; +#7081 = FACE_OUTER_BOUND ( 'NONE', #87405, .T. ) ; +#7082 = VERTEX_POINT ( 'NONE', #94219 ) ; +#7083 = SURFACE_STYLE_FILL_AREA ( #99503 ) ; +#7084 = EDGE_CURVE ( 'NONE', #72651, #67009, #7384, .T. ) ; +#7085 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93423, 'distance_accuracy_value', 'NONE'); +#7086 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33443, 'distance_accuracy_value', 'NONE'); +#7087 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7088 = CARTESIAN_POINT ( 'NONE', ( -0.1737436406883610396, -0.9784189978443861291, 0.8299999999999999600 ) ) ; +#7089 = CARTESIAN_POINT ( 'NONE', ( -0.2155512272691150200, -1.399421068953929925, 0.8299999999999995159 ) ) ; +#7090 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#7091 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#7092 = CARTESIAN_POINT ( 'NONE', ( -0.1410207008655707528, -0.9005569304302141198, 0.8100000000003946266 ) ) ; +#7093 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.250000000000000000, 0.000000000000000000 ) ) ; +#7094 = EDGE_CURVE ( 'NONE', #81943, #28098, #70247, .T. ) ; +#7095 = ORIENTED_EDGE ( 'NONE', *, *, #18696, .F. ) ; +#7096 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7097 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7098 = CARTESIAN_POINT ( 'NONE', ( -0.4143618085515369809, -1.213428637248479935, 0.8100000000000000533 ) ) ; +#7099 = VERTEX_POINT ( 'NONE', #54964 ) ; +#7100 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7101 = ORIENTED_EDGE ( 'NONE', *, *, #69546, .F. ) ; +#7102 = AXIS2_PLACEMENT_3D ( 'NONE', #73308, #57498, #94732 ) ; +#7103 = EDGE_CURVE ( 'NONE', #10022, #11455, #63635, .T. ) ; +#7104 = ADVANCED_FACE ( 'NONE', ( #78925 ), #100765, .F. ) ; +#7105 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#7106 = SURFACE_STYLE_FILL_AREA ( #37847 ) ; +#7107 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#7109 = ORIENTED_EDGE ( 'NONE', *, *, #62174, .T. ) ; +#7108 = ORIENTED_EDGE ( 'NONE', *, *, #35865, .F. ) ; +#7110 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7111 = EDGE_CURVE ( 'NONE', #12591, #82972, #80974, .T. ) ; +#7112 = FACE_OUTER_BOUND ( 'NONE', #1686, .T. ) ; +#7113 = ORIENTED_EDGE ( 'NONE', *, *, #35738, .T. ) ; +#7114 = SURFACE_SIDE_STYLE ('',( #92448 ) ) ; +#7115 = AXIS2_PLACEMENT_3D ( 'NONE', #56219, #18878, #79699 ) ; +#7117 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.500000000000000444, 0.000000000000000000 ) ) ; +#7116 = SURFACE_SIDE_STYLE ('',( #8625 ) ) ; +#7118 = EDGE_LOOP ( 'NONE', ( #16485, #81783, #6302, #1852 ) ) ; +#7119 = ORIENTED_EDGE ( 'NONE', *, *, #12556, .F. ) ; +#7120 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7121 = STYLED_ITEM ( 'NONE', ( #87780 ), #87543 ) ; +#7122 = EDGE_CURVE ( 'NONE', #92575, #50362, #3343, .T. ) ; +#7123 = SURFACE_SIDE_STYLE ('',( #40396 ) ) ; +#7124 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7125 = PRESENTATION_STYLE_ASSIGNMENT (( #46503 ) ) ; +#7126 = ORIENTED_EDGE ( 'NONE', *, *, #31581, .F. ) ; +#7127 = ORIENTED_EDGE ( 'NONE', *, *, #23397, .T. ) ; +#7128 = AXIS2_PLACEMENT_3D ( 'NONE', #69950, #53653, #84774 ) ; +#7129 = AXIS2_PLACEMENT_3D ( 'NONE', #38232, #78037, #46358 ) ; +#7130 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#7131 = EDGE_LOOP ( 'NONE', ( #8527, #36822, #44363, #100695 ) ) ; +#7132 = ADVANCED_FACE ( 'NONE', ( #34511 ), #57488, .T. ) ; +#7133 = LINE ( 'NONE', #67480, #70400 ) ; +#7134 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51347 ) ) ; +#7135 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7136 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40511, #95079, #39989, #86450 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7138 = ORIENTED_EDGE ( 'NONE', *, *, #42364, .F. ) ; +#7137 = SURFACE_STYLE_USAGE ( .BOTH. , #69487 ) ; +#7139 = STYLED_ITEM ( 'NONE', ( #23998 ), #28257 ) ; +#7141 = PLANE ( 'NONE', #33518 ) ; +#7140 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#7142 = LINE ( 'NONE', #31221, #26026 ) ; +#7143 = ORIENTED_EDGE ( 'NONE', *, *, #80316, .T. ) ; +#7145 = PLANE ( 'NONE', #93993 ) ; +#7144 = CIRCLE ( 'NONE', #33352, 0.009999999999999998473 ) ; +#7146 = ORIENTED_EDGE ( 'NONE', *, *, #66447, .T. ) ; +#7147 = CARTESIAN_POINT ( 'NONE', ( -0.02383637504043630354, -0.9153515042605530061, 0.8299999999999988498 ) ) ; +#7148 = VECTOR ( 'NONE', #51826, 1000.000000000000000 ) ; +#7149 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.700000000000000178, -1.793208184573746020E-89 ) ) ; +#7150 = VECTOR ( 'NONE', #76974, 1000.000000000000000 ) ; +#7151 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33368 ) ) ; +#7153 = ORIENTED_EDGE ( 'NONE', *, *, #7692, .T. ) ; +#7152 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#7154 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7155 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7157 = CARTESIAN_POINT ( 'NONE', ( 1.536752279304230084, -1.444662699359980040, 0.8100000000000000533 ) ) ; +#7156 = FILL_AREA_STYLE ('',( #14857 ) ) ; +#7158 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7159 = CARTESIAN_POINT ( 'NONE', ( 1.821320548784939986, -1.306448053922619978, 0.8099999999999996092 ) ) ; +#7160 = ORIENTED_EDGE ( 'NONE', *, *, #84951, .F. ) ; +#7161 = ADVANCED_FACE ( 'NONE', ( #96731 ), #58010, .T. ) ; +#7162 = STYLED_ITEM ( 'NONE', ( #38129 ), #3392 ) ; +#7163 = PRESENTATION_STYLE_ASSIGNMENT (( #77187 ) ) ; +#7164 = VECTOR ( 'NONE', #28716, 1000.000000000000114 ) ; +#7165 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#7166 = AXIS2_PLACEMENT_3D ( 'NONE', #35268, #60260, #67369 ) ; +#7167 = EDGE_CURVE ( 'NONE', #98298, #79581, #66128, .T. ) ; +#7169 = CARTESIAN_POINT ( 'NONE', ( 1.255926156707774410, -1.444270688870365360, 0.8099999999997105071 ) ) ; +#7168 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2761799387799150352, -0.02000000000000000042 ) ) ; +#7170 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7171 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#7172 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7173 = VECTOR ( 'NONE', #98911, 1000.000000000000000 ) ; +#7174 = FACE_OUTER_BOUND ( 'NONE', #45950, .T. ) ; +#7175 = LINE ( 'NONE', #38417, #78473 ) ; +#7176 = VERTEX_POINT ( 'NONE', #79450 ) ; +#7177 = STYLED_ITEM ( 'NONE', ( #90496 ), #72567 ) ; +#7178 = PRESENTATION_STYLE_ASSIGNMENT (( #19708 ) ) ; +#7179 = SURFACE_STYLE_FILL_AREA ( #77202 ) ; +#7180 = ORIENTED_EDGE ( 'NONE', *, *, #52798, .T. ) ; +#7181 = SURFACE_STYLE_FILL_AREA ( #77208 ) ; +#7182 = SURFACE_SIDE_STYLE ('',( #46029 ) ) ; +#7183 = FILL_AREA_STYLE ('',( #30235 ) ) ; +#7184 = VECTOR ( 'NONE', #70968, 1000.000000000000000 ) ; +#7185 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7186 = VERTEX_POINT ( 'NONE', #9408 ) ; +#7187 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#7188 = EDGE_CURVE ( 'NONE', #30322, #12756, #40645, .T. ) ; +#7189 = SURFACE_SIDE_STYLE ('',( #77217 ) ) ; +#7190 = CARTESIAN_POINT ( 'NONE', ( -0.08150952889499120391, -1.159841243706410063, 0.8300000000000005151 ) ) ; +#7191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7192 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7193 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7194 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21880 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30675, #46501, #15856 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7195 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80715 ) ) ; +#7196 = FILL_AREA_STYLE ('',( #5738 ) ) ; +#7197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7198 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#7199 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7200 = SURFACE_STYLE_FILL_AREA ( #29752 ) ; +#7201 = PLANE ( 'NONE', #43711 ) ; +#7202 = VECTOR ( 'NONE', #96952, 1000.000000000000000 ) ; +#7203 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86519 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59407, #20544, #41542 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7204 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8199999999999999512 ) ) ; +#7205 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #65589, #48798 ), + ( #19116, #81459 ), + ( #42624, #3807 ), + ( #97215, #27315 ), + ( #58488, #19634 ), + ( #9380, #40621 ), + ( #71753, #79931 ), + ( #1811, #59981 ), + ( #29784, #82439 ), + ( #22132, #5772 ), + ( #92073, #60966 ), + ( #28308, #81947 ), + ( #52306, #37482 ), + ( #6251, #59493 ), + ( #35986, #74267 ), + ( #99158, #90587 ), + ( #97691, #20119 ), + ( #68583, #13395 ), + ( #99631, #44589 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06525924122584060572, 0.1303097080177630096, 0.1949669058053019877, 0.2594204141250899820, 0.3228188495375590161, 0.3840951885662929888, 0.4433054993635430208, 0.5020719067220029697, 0.5599285383667119698, 0.6178537031467939977, 0.6762349939776259866, 0.7358459849262459773, 0.7974378458162040273, 0.8614696408465449817, 0.9284772069666370475, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7206 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30009, 'distance_accuracy_value', 'NONE'); +#7207 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54556 ) ) ; +#7208 = VERTEX_POINT ( 'NONE', #18113 ) ; +#7209 = FILL_AREA_STYLE_COLOUR ( '', #75811 ) ; +#7210 = ORIENTED_EDGE ( 'NONE', *, *, #20179, .T. ) ; +#7211 = CYLINDRICAL_SURFACE ( 'NONE', #1346, 0.009999999999999998473 ) ; +#7212 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90511, 'distance_accuracy_value', 'NONE'); +#7213 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87650, 'distance_accuracy_value', 'NONE'); +#7214 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#7215 = LINE ( 'NONE', #54285, #41632 ) ; +#7216 = CARTESIAN_POINT ( 'NONE', ( -1.105094510553189968, -1.513291690750319995, 0.8299999999999981837 ) ) ; +#7217 = CIRCLE ( 'NONE', #15436, 0.09999999999999939493 ) ; +#7218 = SURFACE_SIDE_STYLE ('',( #22120 ) ) ; +#7219 = VECTOR ( 'NONE', #29883, 1000.000000000000114 ) ; +#7220 = CARTESIAN_POINT ( 'NONE', ( -0.07152490633971099465, -1.505252428432260148, 0.8300000000000004041 ) ) ; +#7221 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7222 = SURFACE_STYLE_FILL_AREA ( #45554 ) ; +#7223 = STYLED_ITEM ( 'NONE', ( #8580 ), #22133 ) ; +#7224 = CARTESIAN_POINT ( 'NONE', ( -0.7522321428571430157, 0.7099999999999999645, 0.2077922077922079724 ) ) ; +#7225 = ORIENTED_EDGE ( 'NONE', *, *, #74389, .T. ) ; +#7226 = LINE ( 'NONE', #78278, #41126 ) ; +#7227 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#7228 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34182, 'distance_accuracy_value', 'NONE'); +#7231 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7230 = STYLED_ITEM ( 'NONE', ( #9784 ), #38568 ) ; +#7229 = PRESENTATION_STYLE_ASSIGNMENT (( #93539 ) ) ; +#7232 = VERTEX_POINT ( 'NONE', #17625 ) ; +#7233 = SURFACE_STYLE_FILL_AREA ( #63964 ) ; +#7234 = VECTOR ( 'NONE', #74850, 1000.000000000000000 ) ; +#7235 = ORIENTED_EDGE ( 'NONE', *, *, #100111, .F. ) ; +#7236 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 4.680228999999999751, 0.8648700000000000276 ) ) ; +#7237 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7238 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7239 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#7240 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7241 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#7242 = ORIENTED_EDGE ( 'NONE', *, *, #55999, .T. ) ; +#7243 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53037 ) ) ; +#7244 = PRESENTATION_STYLE_ASSIGNMENT (( #77257 ) ) ; +#7245 = ADVANCED_FACE ( 'NONE', ( #1840 ), #32974, .T. ) ; +#7246 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22204, 'distance_accuracy_value', 'NONE'); +#7247 = SURFACE_STYLE_USAGE ( .BOTH. , #54303 ) ; +#7248 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7249 = ORIENTED_EDGE ( 'NONE', *, *, #48810, .F. ) ; +#7250 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72566 ) ) ; +#7251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7252 = CARTESIAN_POINT ( 'NONE', ( 7.386065750250000228, 3.435720750249999789, 0.8991599999999999593 ) ) ; +#7253 = ORIENTED_EDGE ( 'NONE', *, *, #19629, .F. ) ; +#7255 = ORIENTED_EDGE ( 'NONE', *, *, #52401, .T. ) ; +#7254 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72568 ) ) ; +#7256 = PLANE ( 'NONE', #40100 ) ; +#7257 = VERTEX_POINT ( 'NONE', #28333 ) ; +#7258 = EDGE_CURVE ( 'NONE', #57121, #35264, #99184, .T. ) ; +#7259 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56287 ) ) ; +#7260 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7261 = ORIENTED_EDGE ( 'NONE', *, *, #61900, .T. ) ; +#7263 = ORIENTED_EDGE ( 'NONE', *, *, #41555, .T. ) ; +#7262 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#7264 = SURFACE_SIDE_STYLE ('',( #53815 ) ) ; +#7266 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#7265 = FILL_AREA_STYLE_COLOUR ( '', #49327 ) ; +#7268 = LINE ( 'NONE', #100642, #43164 ) ; +#7267 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65236 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3395, #87146, #88156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7269 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -11.36999999999999922 ) ) ; +#7270 = VERTEX_POINT ( 'NONE', #44618 ) ; +#7271 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#7272 = SURFACE_STYLE_USAGE ( .BOTH. , #84948 ) ; +#7273 = VERTEX_POINT ( 'NONE', #43133 ) ; +#7274 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20619 ), #100375 ) ; +#7275 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#7276 = STYLED_ITEM ( 'NONE', ( #20404 ), #82437 ) ; +#7277 = STYLED_ITEM ( 'NONE', ( #79896 ), #88896 ) ; +#7278 = EDGE_LOOP ( 'NONE', ( #7138, #25134, #83557, #43734 ) ) ; +#7281 = SURFACE_SIDE_STYLE ('',( #99196 ) ) ; +#7280 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7279 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49816 ), #72589 ) ; +#7282 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98592 ) ) ; +#7283 = ORIENTED_EDGE ( 'NONE', *, *, #23191, .F. ) ; +#7284 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100176 ) ) ; +#7285 = EDGE_CURVE ( 'NONE', #95068, #63412, #4821, .T. ) ; +#7287 = PLANE ( 'NONE', #10575 ) ; +#7286 = FILL_AREA_STYLE ('',( #99677 ) ) ; +#7288 = FILL_AREA_STYLE ('',( #61521 ) ) ; +#7289 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12176 ) ) ; +#7290 = FACE_OUTER_BOUND ( 'NONE', #13602, .T. ) ; +#7291 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82397 ), #27010 ) ; +#7292 = ORIENTED_EDGE ( 'NONE', *, *, #21900, .F. ) ; +#7293 = EDGE_LOOP ( 'NONE', ( #63882, #6974, #63268, #85063 ) ) ; +#7294 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7295 = EDGE_CURVE ( 'NONE', #56777, #65486, #67596, .T. ) ; +#7296 = FILL_AREA_STYLE ('',( #71685 ) ) ; +#7297 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1199999999999999956, -1.000000000000000000 ) ) ; +#7298 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18817 ) ) ; +#7299 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57697 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6694, #60933, #51260 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7300 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33441, 'distance_accuracy_value', 'NONE'); +#7301 = DIRECTION ( 'NONE', ( -1.425188158846549879E-32, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#7302 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7303 = SURFACE_STYLE_FILL_AREA ( #10699 ) ; +#7304 = SURFACE_STYLE_USAGE ( .BOTH. , #61033 ) ; +#7305 = SURFACE_STYLE_FILL_AREA ( #6789 ) ; +#7306 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.500000000000000000, -0.02000000000002094894 ) ) ; +#7307 = VERTEX_POINT ( 'NONE', #12920 ) ; +#7308 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71326 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61394, #15866, #53700 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7309 = LINE ( 'NONE', #98730, #50158 ) ; +#7310 = AXIS2_PLACEMENT_3D ( 'NONE', #75762, #5773, #99159 ) ; +#7311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7312 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#7313 = FILL_AREA_STYLE_COLOUR ( '', #2065 ) ; +#7314 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7315 = VERTEX_POINT ( 'NONE', #59012 ) ; +#7316 = SURFACE_STYLE_USAGE ( .BOTH. , #51878 ) ; +#7317 = EDGE_CURVE ( 'NONE', #98312, #5244, #36511, .T. ) ; +#7318 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#7319 = FILL_AREA_STYLE ('',( #52383 ) ) ; +#7320 = CARTESIAN_POINT ( 'NONE', ( -0.03242561202523040059, -1.422222704560690110, 0.8299999999999999600 ) ) ; +#7321 = FILL_AREA_STYLE_COLOUR ( '', #46900 ) ; +#7322 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7323 = SURFACE_SIDE_STYLE ('',( #55914 ) ) ; +#7324 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7325 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7326 = SURFACE_STYLE_FILL_AREA ( #46172 ) ; +#7327 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7328 = LINE ( 'NONE', #36578, #89805 ) ; +#7329 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#7330 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 6.822763000000000133, 0.8648700000000000276 ) ) ; +#7331 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55631, #100911, #70927 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7332 = FILL_AREA_STYLE_COLOUR ( '', #77996 ) ; +#7333 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.499999999999980016, 0.1829999999999999960 ) ) ; +#7334 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19348, 'distance_accuracy_value', 'NONE'); +#7335 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -11.36999999999999922 ) ) ; +#7336 = CARTESIAN_POINT ( 'NONE', ( 1.157511986614659261, 1.258646575926970490, 0.8100000000000000533 ) ) ; +#7337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50689, 'distance_accuracy_value', 'NONE'); +#7338 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, 0.9464466094067262025 ) ) ; +#7339 = VECTOR ( 'NONE', #91735, 1000.000000000000000 ) ; +#7340 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7341 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#7342 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7343 = CARTESIAN_POINT ( 'NONE', ( -0.9584150915164789675, -1.224577966852969935, 0.8100000000000000533 ) ) ; +#7344 = EDGE_CURVE ( 'NONE', #15748, #28356, #98680, .T. ) ; +#7345 = ORIENTED_EDGE ( 'NONE', *, *, #43769, .T. ) ; +#7346 = VECTOR ( 'NONE', #45222, 1000.000000000000000 ) ; +#7347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7348 = EDGE_CURVE ( 'NONE', #79963, #8011, #52478, .T. ) ; +#7349 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13805, 'distance_accuracy_value', 'NONE'); +#7350 = VECTOR ( 'NONE', #71599, 1000.000000000000000 ) ; +#7351 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, 3.500000000000000444, 0.000000000000000000 ) ) ; +#7352 = AXIS2_PLACEMENT_3D ( 'NONE', #8018, #77555, #14213 ) ; +#7353 = ORIENTED_EDGE ( 'NONE', *, *, #26355, .T. ) ; +#7354 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7355 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7356 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.266666666666647068, 0.000000000000000000 ) ) ; +#7357 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.233333333333333393, 0.000000000000000000 ) ) ; +#7358 = FILL_AREA_STYLE_COLOUR ( '', #45691 ) ; +#7359 = FILL_AREA_STYLE_COLOUR ( '', #49472 ) ; +#7360 = ORIENTED_EDGE ( 'NONE', *, *, #44097, .F. ) ; +#7361 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7362 = EDGE_CURVE ( 'NONE', #466, #66883, #28818, .T. ) ; +#7363 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69797, 'distance_accuracy_value', 'NONE'); +#7364 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92194 ), #892 ) ; +#7365 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7366 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97142 ), #12255 ) ; +#7367 = VERTEX_POINT ( 'NONE', #81967 ) ; +#7368 = ORIENTED_EDGE ( 'NONE', *, *, #97143, .F. ) ; +#7369 = VECTOR ( 'NONE', #40413, 1000.000000000000000 ) ; +#7370 = VECTOR ( 'NONE', #81790, 1000.000000000000000 ) ; +#7371 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#7372 = ORIENTED_EDGE ( 'NONE', *, *, #89627, .F. ) ; +#7373 = FILL_AREA_STYLE ('',( #60121 ) ) ; +#7374 = CARTESIAN_POINT ( 'NONE', ( 0.01835565287466199916, -1.473933850988760064, 0.8299999999999999600 ) ) ; +#7375 = CARTESIAN_POINT ( 'NONE', ( 0.4675224071360329914, -1.231957836876500068, 0.8100000000000000533 ) ) ; +#7376 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7377 = ADVANCED_FACE ( 'NONE', ( #60503 ), #91601, .T. ) ; +#7378 = VECTOR ( 'NONE', #53573, 1000.000000000000000 ) ; +#7379 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #87659, #58257 ) ; +#7380 = ORIENTED_EDGE ( 'NONE', *, *, #24328, .T. ) ; +#7381 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59714 ) ) ; +#7382 = VERTEX_POINT ( 'NONE', #24213 ) ; +#7383 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40626 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11258, #19511, #55080 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7384 = LINE ( 'NONE', #93690, #92998 ) ; +#7386 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8991599999999999593 ) ) ; +#7385 = FILL_AREA_STYLE_COLOUR ( '', #52536 ) ; +#7387 = ORIENTED_EDGE ( 'NONE', *, *, #53147, .T. ) ; +#7388 = FILL_AREA_STYLE ('',( #77411 ) ) ; +#7390 = VERTEX_POINT ( 'NONE', #84943 ) ; +#7389 = EDGE_CURVE ( 'NONE', #21657, #15159, #23687, .T. ) ; +#7391 = VECTOR ( 'NONE', #40176, 1000.000000000000000 ) ; +#7392 = FILL_AREA_STYLE_COLOUR ( '', #19157 ) ; +#7393 = ORIENTED_EDGE ( 'NONE', *, *, #21569, .F. ) ; +#7394 = VERTEX_POINT ( 'NONE', #6751 ) ; +#7395 = CARTESIAN_POINT ( 'NONE', ( 1.354949560415620091, -1.296162859166370307, 0.8100000000000000533 ) ) ; +#7396 = EDGE_CURVE ( 'NONE', #5956, #84098, #39494, .T. ) ; +#7397 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7398 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7399 = FACE_OUTER_BOUND ( 'NONE', #65141, .T. ) ; +#7400 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.000000000000000000 ) ) ; +#7401 = EDGE_LOOP ( 'NONE', ( #30314, #63756, #762, #63257 ) ) ; +#7402 = SURFACE_STYLE_FILL_AREA ( #92719 ) ; +#7403 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7404 = FILL_AREA_STYLE_COLOUR ( '', #76036 ) ; +#7405 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36093 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39843, #8095, #48531 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7406 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#7407 = AXIS2_PLACEMENT_3D ( 'NONE', #71458, #78593, #46429 ) ; +#7408 = ORIENTED_EDGE ( 'NONE', *, *, #26045, .T. ) ; +#7409 = LINE ( 'NONE', #840, #56452 ) ; +#7410 = SURFACE_SIDE_STYLE ('',( #77431 ) ) ; +#7411 = ORIENTED_EDGE ( 'NONE', *, *, #26407, .T. ) ; +#7412 = ORIENTED_EDGE ( 'NONE', *, *, #26402, .F. ) ; +#7413 = FILL_AREA_STYLE_COLOUR ( '', #4605 ) ; +#7414 = EDGE_CURVE ( 'NONE', #89499, #91599, #29810, .T. ) ; +#7416 = SURFACE_SIDE_STYLE ('',( #77953 ) ) ; +#7415 = SURFACE_STYLE_USAGE ( .BOTH. , #96888 ) ; +#7417 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7418 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13375 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97113, #3708, #50221 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7419 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7420 = PRESENTATION_STYLE_ASSIGNMENT (( #15111 ) ) ; +#7421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90669 ), #58130 ) ; +#7422 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999979572, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#7423 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#7424 = VECTOR ( 'NONE', #98414, 1000.000000000000000 ) ; +#7425 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #69330 ) ; +#7426 = FACE_OUTER_BOUND ( 'NONE', #76516, .T. ) ; +#7427 = SURFACE_STYLE_FILL_AREA ( #14622 ) ; +#7428 = ORIENTED_EDGE ( 'NONE', *, *, #72528, .T. ) ; +#7429 = AXIS2_PLACEMENT_3D ( 'NONE', #17751, #80086, #71395 ) ; +#7430 = ORIENTED_EDGE ( 'NONE', *, *, #98871, .T. ) ; +#7431 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#7432 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7433 = CARTESIAN_POINT ( 'NONE', ( 1.133718228224829927, -1.135808780994409961, 0.8100000000000000533 ) ) ; +#7434 = LINE ( 'NONE', #47836, #64384 ) ; +#7435 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51566 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26546, #10097, #9118 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7436 = SURFACE_STYLE_FILL_AREA ( #53987 ) ; +#7437 = LINE ( 'NONE', #55532, #84373 ) ; +#7438 = SURFACE_STYLE_USAGE ( .BOTH. , #14633 ) ; +#7439 = SURFACE_SIDE_STYLE ('',( #15653 ) ) ; +#7440 = ORIENTED_EDGE ( 'NONE', *, *, #7389, .T. ) ; +#7441 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.399999999999999911, -13.35000000000000142 ) ) ; +#7442 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7443 = AXIS2_PLACEMENT_3D ( 'NONE', #74619, #4641, #82772 ) ; +#7444 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7445 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3999, 'distance_accuracy_value', 'NONE'); +#7446 = EDGE_CURVE ( 'NONE', #19073, #9287, #55365, .T. ) ; +#7447 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44345 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49519, #80676, #10598 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7448 = EDGE_CURVE ( 'NONE', #30264, #60642, #78316, .T. ) ; +#7449 = FACE_OUTER_BOUND ( 'NONE', #37387, .T. ) ; +#7450 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25177 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31333, #68106, #45601 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7451 = LINE ( 'NONE', #15148, #7821 ) ; +#7452 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7453 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000311, 0.000000000000000000 ) ) ; +#7454 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#7455 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22261 ) ) ; +#7456 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#7458 = LINE ( 'NONE', #91426, #16235 ) ; +#7457 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80287 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48921, #63745, #71376 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7460 = EDGE_CURVE ( 'NONE', #47153, #46344, #60992, .T. ) ; +#7461 = EDGE_LOOP ( 'NONE', ( #64390, #9972, #22847, #20168 ) ) ; +#7462 = DIRECTION ( 'NONE', ( 0.8942439631056310345, 0.4475798637663839785, 0.000000000000000000 ) ) ; +#7463 = SURFACE_SIDE_STYLE ('',( #31031 ) ) ; +#7464 = CARTESIAN_POINT ( 'NONE', ( 1.568874050374579943, -1.341601374162270099, 0.8299999999999977396 ) ) ; +#7465 = EDGE_CURVE ( 'NONE', #23828, #5956, #15988, .T. ) ; +#7466 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51719, 'distance_accuracy_value', 'NONE'); +#7467 = ADVANCED_FACE ( 'NONE', ( #686 ), #85451, .T. ) ; +#7468 = STYLED_ITEM ( 'NONE', ( #26129 ), #73719 ) ; +#7469 = FILL_AREA_STYLE_COLOUR ( '', #77479 ) ; +#7470 = CARTESIAN_POINT ( 'NONE', ( 1.318335579244860112, -1.183201991847933066, 0.8099999999998749312 ) ) ; +#7471 = CARTESIAN_POINT ( 'NONE', ( 1.793184587716770029, -1.490633633148249926, 0.8300000000000011813 ) ) ; +#7472 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2850000000000000311, 0.1400000000000000133 ) ) ; +#7473 = EDGE_LOOP ( 'NONE', ( #78211, #26641, #7772, #67605, #34955 ) ) ; +#7474 = PRESENTATION_STYLE_ASSIGNMENT (( #47374 ) ) ; +#7475 = CARTESIAN_POINT ( 'NONE', ( 1.748219681435579931, -1.226312279485590073, 0.8299999999999994049 ) ) ; +#7476 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62880, #39352, #100511, #71020 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7477 = ADVANCED_FACE ( 'NONE', ( #77281 ), #45594, .T. ) ; +#7478 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44308, 'distance_accuracy_value', 'NONE'); +#7479 = SURFACE_STYLE_USAGE ( .BOTH. , #82672 ) ; +#7480 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90072, 'distance_accuracy_value', 'NONE'); +#7481 = PRESENTATION_STYLE_ASSIGNMENT (( #39209 ) ) ; +#7482 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61464 ) ) ; +#7483 = EDGE_LOOP ( 'NONE', ( #98324, #97477, #13826, #29584 ) ) ; +#7484 = ADVANCED_FACE ( 'NONE', ( #34390 ), #41534, .T. ) ; +#7486 = VERTEX_POINT ( 'NONE', #56873 ) ; +#7485 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35110 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86223, #79091, #24490 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7487 = SURFACE_SIDE_STYLE ('',( #85168 ) ) ; +#7488 = ORIENTED_EDGE ( 'NONE', *, *, #21988, .T. ) ; +#7489 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82378 ) ) ; +#7490 = SURFACE_STYLE_FILL_AREA ( #62732 ) ; +#7491 = FILL_AREA_STYLE_COLOUR ( '', #67901 ) ; +#7492 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7493 = EDGE_CURVE ( 'NONE', #95470, #61212, #79233, .T. ) ; +#7494 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #28059 ) ; +#7495 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 6.776263578034399754E-16 ) ) ; +#7496 = FACE_OUTER_BOUND ( 'NONE', #68246, .T. ) ; +#7497 = EDGE_CURVE ( 'NONE', #63162, #31184, #33376, .T. ) ; +#7499 = ORIENTED_EDGE ( 'NONE', *, *, #100244, .T. ) ; +#7498 = ORIENTED_EDGE ( 'NONE', *, *, #35269, .F. ) ; +#7500 = VERTEX_POINT ( 'NONE', #57897 ) ; +#7501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7502 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#7503 = ORIENTED_EDGE ( 'NONE', *, *, #74663, .F. ) ; +#7504 = PRODUCT_DEFINITION ( 'δ֪', '', #87801, #94294 ) ; +#7505 = LINE ( 'NONE', #6521, #46558 ) ; +#7506 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7508 = PLANE ( 'NONE', #10727 ) ; +#7507 = SURFACE_SIDE_STYLE ('',( #53572 ) ) ; +#7509 = ORIENTED_EDGE ( 'NONE', *, *, #48180, .T. ) ; +#7510 = ORIENTED_EDGE ( 'NONE', *, *, #77036, .T. ) ; +#7511 = ORIENTED_EDGE ( 'NONE', *, *, #98552, .F. ) ; +#7512 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#7513 = VECTOR ( 'NONE', #28224, 1000.000000000000000 ) ; +#7514 = EDGE_CURVE ( 'NONE', #31304, #94230, #65490, .T. ) ; +#7515 = SURFACE_SIDE_STYLE ('',( #23971 ) ) ; +#7516 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23972 ), #44889 ) ; +#7517 = LINE ( 'NONE', #31596, #19508 ) ; +#7518 = VERTEX_POINT ( 'NONE', #19023 ) ; +#7519 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.300000000000000266, 8.972889346935576195E-79 ) ) ; +#7520 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#7521 = FILL_AREA_STYLE_COLOUR ( '', #75070 ) ; +#7522 = ORIENTED_EDGE ( 'NONE', *, *, #11964, .F. ) ; +#7523 = LINE ( 'NONE', #87234, #32183 ) ; +#7524 = ORIENTED_EDGE ( 'NONE', *, *, #5272, .F. ) ; +#7525 = ORIENTED_EDGE ( 'NONE', *, *, #497, .T. ) ; +#7526 = ADVANCED_FACE ( 'NONE', ( #32358 ), #24729, .T. ) ; +#7527 = PRESENTATION_STYLE_ASSIGNMENT (( #77569 ) ) ; +#7528 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.000000000000000000 ) ) ; +#7529 = ADVANCED_FACE ( 'NONE', ( #75187 ), #74685, .T. ) ; +#7530 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35096 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84733, #38781, #29607 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7531 = SURFACE_STYLE_FILL_AREA ( #69371 ) ; +#7532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7533 = FACE_OUTER_BOUND ( 'NONE', #23559, .T. ) ; +#7534 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000007688, -3.149999999999979927, 0.000000000000000000 ) ) ; +#7535 = CARTESIAN_POINT ( 'NONE', ( 0.2777831599446540234, -0.9154070317056139938, 0.8300000000000020695 ) ) ; +#7536 = VECTOR ( 'NONE', #23480, 1000.000000000000000 ) ; +#7537 = ORIENTED_EDGE ( 'NONE', *, *, #87145, .F. ) ; +#7538 = FILL_AREA_STYLE ('',( #69379 ) ) ; +#7539 = CARTESIAN_POINT ( 'NONE', ( 0.05204425658606930821, -1.220010286732279958, 0.8299999999999999600 ) ) ; +#7540 = ORIENTED_EDGE ( 'NONE', *, *, #51217, .T. ) ; +#7541 = EDGE_CURVE ( 'NONE', #38717, #60734, #4221, .T. ) ; +#7542 = LINE ( 'NONE', #47956, #47229 ) ; +#7543 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7544 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7545 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#7546 = STYLED_ITEM ( 'NONE', ( #91658 ), #83912 ) ; +#7547 = VECTOR ( 'NONE', #35928, 1000.000000000000000 ) ; +#7548 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7550 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999667, 0.1900000000000000022 ) ) ; +#7549 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2808578643762690841, -0.1499999999999999944 ) ) ; +#7551 = CARTESIAN_POINT ( 'NONE', ( 1.799895807589950048, -1.058723197808659977, 0.8299999999999999600 ) ) ; +#7552 = VECTOR ( 'NONE', #99719, 1000.000000000000000 ) ; +#7553 = FACE_OUTER_BOUND ( 'NONE', #65353, .T. ) ; +#7554 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7555 = LINE ( 'NONE', #99953, #41239 ) ; +#7556 = CYLINDRICAL_SURFACE ( 'NONE', #13629, 0.04999999999999991257 ) ; +#7557 = DIRECTION ( 'NONE', ( 5.551115123125780237E-17, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#7558 = FILL_AREA_STYLE_COLOUR ( '', #31992 ) ; +#7559 = ADVANCED_FACE ( 'NONE', ( #44502 ), #48075, .T. ) ; +#7560 = ADVANCED_FACE ( 'NONE', ( #1094 ), #94504, .F. ) ; +#7561 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48501 ) ) ; +#7563 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7562 = LINE ( 'NONE', #53131, #24529 ) ; +#7564 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#7565 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7566 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7567 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59827 ), #64737 ) ; +#7568 = AXIS2_PLACEMENT_3D ( 'NONE', #98035, #99014, #29178 ) ; +#7569 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62480, 'distance_accuracy_value', 'NONE'); +#7570 = EDGE_LOOP ( 'NONE', ( #17256, #50356, #44051, #57812 ) ) ; +#7571 = CLOSED_SHELL ( 'NONE', ( #51833, #79828, #47481, #83982, #66456, #93875 ) ) ; +#7572 = FILL_AREA_STYLE ('',( #55173 ) ) ; +#7574 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7573 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8648700000000000276 ) ) ; +#7575 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.300000000000000266, 0.000000000000000000 ) ) ; +#7576 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8648700000000000276 ) ) ; +#7577 = EDGE_CURVE ( 'NONE', #84381, #92470, #27886, .T. ) ; +#7578 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7579 = PLANE ( 'NONE', #33582 ) ; +#7580 = PLANE ( 'NONE', #6472 ) ; +#7582 = EDGE_CURVE ( 'NONE', #76527, #47331, #78213, .T. ) ; +#7581 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #63942, #25166, #87413, #56308 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7583 = FILL_AREA_STYLE ('',( #77619 ) ) ; +#7584 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93260 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16323, #25070, #54168 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7585 = VERTEX_POINT ( 'NONE', #8162 ) ; +#7586 = ORIENTED_EDGE ( 'NONE', *, *, #50013, .F. ) ; +#7587 = PRESENTATION_STYLE_ASSIGNMENT (( #63840 ) ) ; +#7588 = SURFACE_STYLE_FILL_AREA ( #46454 ) ; +#7589 = LINE ( 'NONE', #9613, #64579 ) ; +#7590 = AXIS2_PLACEMENT_3D ( 'NONE', #86850, #31707, #16351 ) ; +#7591 = SURFACE_STYLE_FILL_AREA ( #8097 ) ; +#7592 = SURFACE_STYLE_USAGE ( .BOTH. , #46457 ) ; +#7593 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.8999999999999990230, -0.02000000000001120326 ) ) ; +#7594 = LINE ( 'NONE', #100483, #42406 ) ; +#7595 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#7596 = VERTEX_POINT ( 'NONE', #87366 ) ; +#7597 = LINE ( 'NONE', #16319, #67985 ) ; +#7598 = DIRECTION ( 'NONE', ( 0.7071067811865395791, 0.7071067811865554553, 0.000000000000000000 ) ) ; +#7599 = ORIENTED_EDGE ( 'NONE', *, *, #56906, .F. ) ; +#7600 = EDGE_CURVE ( 'NONE', #56959, #30679, #55254, .T. ) ; +#7601 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#7602 = ORIENTED_EDGE ( 'NONE', *, *, #58278, .F. ) ; +#7603 = STYLED_ITEM ( 'NONE', ( #3397 ), #74196 ) ; +#7604 = CARTESIAN_POINT ( 'NONE', ( 1.058713228792119931, -1.379057077391790287, 0.8299999999999999600 ) ) ; +#7605 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#7606 = LINE ( 'NONE', #77652, #34883 ) ; +#7607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45204 ) ) ; +#7608 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7609 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7610 = CARTESIAN_POINT ( 'NONE', ( -0.9938630133853416648, 2.355709075926968765, 0.8299999999999999600 ) ) ; +#7611 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#7612 = EDGE_CURVE ( 'NONE', #25241, #6655, #91647, .T. ) ; +#7614 = ORIENTED_EDGE ( 'NONE', *, *, #28779, .T. ) ; +#7613 = ORIENTED_EDGE ( 'NONE', *, *, #90029, .F. ) ; +#7615 = FACE_OUTER_BOUND ( 'NONE', #9773, .T. ) ; +#7616 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#7617 = EDGE_LOOP ( 'NONE', ( #91376, #99816, #39888, #22912 ) ) ; +#7618 = SURFACE_SIDE_STYLE ('',( #93446 ) ) ; +#7619 = EDGE_LOOP ( 'NONE', ( #34162, #68369, #87974, #67025, #48106, #95188 ) ) ; +#7620 = VECTOR ( 'NONE', #58950, 1000.000000000000000 ) ; +#7621 = VERTEX_POINT ( 'NONE', #8657 ) ; +#7622 = LINE ( 'NONE', #8130, #53083 ) ; +#7623 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7624 = SURFACE_SIDE_STYLE ('',( #31206 ) ) ; +#7625 = LINE ( 'NONE', #76659, #41624 ) ; +#7626 = VERTEX_POINT ( 'NONE', #39907 ) ; +#7627 = ORIENTED_EDGE ( 'NONE', *, *, #85734, .F. ) ; +#7628 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8648700000000000276 ) ) ; +#7629 = ORIENTED_EDGE ( 'NONE', *, *, #78085, .F. ) ; +#7630 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#7631 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87685 ) ) ; +#7632 = ADVANCED_FACE ( 'NONE', ( #33262 ), #48596, .T. ) ; +#7633 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77526 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63335, #32164, #30607 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7635 = EDGE_LOOP ( 'NONE', ( #56444, #21160, #66210, #45934 ) ) ; +#7634 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8648700000000000276 ) ) ; +#7636 = VECTOR ( 'NONE', #20596, 1000.000000000000000 ) ; +#7637 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7638 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7640 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6067 ) ) ; +#7639 = LINE ( 'NONE', #23073, #99303 ) ; +#7641 = ORIENTED_EDGE ( 'NONE', *, *, #43161, .T. ) ; +#7642 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.000000000000000000, 0.1900000000000000022 ) ) ; +#7643 = CLOSED_SHELL ( 'NONE', ( #3748, #61860, #35834, #616, #57115, #93325 ) ) ; +#7644 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7645 = ORIENTED_EDGE ( 'NONE', *, *, #42914, .F. ) ; +#7646 = EDGE_CURVE ( 'NONE', #81966, #27604, #12196, .T. ) ; +#7647 = LINE ( 'NONE', #40423, #57978 ) ; +#7648 = VECTOR ( 'NONE', #100067, 1000.000000000000114 ) ; +#7649 = ADVANCED_FACE ( 'NONE', ( #19941 ), #57781, .T. ) ; +#7650 = EDGE_LOOP ( 'NONE', ( #32111, #41360, #64076, #63354 ) ) ; +#7651 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#7652 = PRESENTATION_STYLE_ASSIGNMENT (( #22056 ) ) ; +#7654 = DIRECTION ( 'NONE', ( -2.567390744445670062E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7653 = SURFACE_SIDE_STYLE ('',( #23086 ) ) ; +#7655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7656 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#7657 = SURFACE_STYLE_USAGE ( .BOTH. , #77697 ) ; +#7659 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 15.15000000000000036, 0.000000000000000000 ) ) ; +#7658 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#7660 = ORIENTED_EDGE ( 'NONE', *, *, #27804, .F. ) ; +#7661 = EDGE_CURVE ( 'NONE', #53940, #65920, #18920, .T. ) ; +#7662 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8991599999999999593 ) ) ; +#7663 = SURFACE_SIDE_STYLE ('',( #62406 ) ) ; +#7664 = AXIS2_PLACEMENT_3D ( 'NONE', #58465, #65565, #89066 ) ; +#7665 = SURFACE_STYLE_USAGE ( .BOTH. , #22065 ) ; +#7666 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7667 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7668 = ADVANCED_FACE ( 'NONE', ( #88890 ), #5084, .F. ) ; +#7670 = LINE ( 'NONE', #1109, #65474 ) ; +#7669 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7671 = FILL_AREA_STYLE ('',( #69520 ) ) ; +#7672 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#7673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7674 = AXIS2_PLACEMENT_3D ( 'NONE', #75161, #89953, #98047 ) ; +#7675 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#7676 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#7677 = ORIENTED_EDGE ( 'NONE', *, *, #60736, .F. ) ; +#7678 = LINE ( 'NONE', #38919, #97122 ) ; +#7679 = EDGE_CURVE ( 'NONE', #57258, #88552, #10676, .T. ) ; +#7680 = EDGE_CURVE ( 'NONE', #24035, #22678, #3623, .T. ) ; +#7681 = ORIENTED_EDGE ( 'NONE', *, *, #43082, .F. ) ; +#7682 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7683 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#7684 = ADVANCED_FACE ( 'NONE', ( #97009 ), #4120, .F. ) ; +#7685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7686 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.000000000000000000 ) ) ; +#7687 = ORIENTED_EDGE ( 'NONE', *, *, #24910, .F. ) ; +#7688 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#7689 = STYLED_ITEM ( 'NONE', ( #19860 ), #55414 ) ; +#7690 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999985359, -0.1458578643762690474 ) ) ; +#7691 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7692 = EDGE_CURVE ( 'NONE', #61427, #45932, #83743, .T. ) ; +#7693 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#7694 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7695 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90962 ) ) ; +#7696 = FILL_AREA_STYLE ('',( #8206 ) ) ; +#7697 = PLANE ( 'NONE', #60514 ) ; +#7698 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7699 = ADVANCED_FACE ( 'NONE', ( #99934 ), #13719, .F. ) ; +#7700 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7701 = PLANE ( 'NONE', #29729 ) ; +#7702 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7703 = SURFACE_SIDE_STYLE ('',( #46584 ) ) ; +#7704 = CIRCLE ( 'NONE', #64879, 0.09999999999999939493 ) ; +#7705 = EDGE_LOOP ( 'NONE', ( #4476, #50445, #30978, #41996 ) ) ; +#7706 = LINE ( 'NONE', #93017, #41581 ) ; +#7707 = ORIENTED_EDGE ( 'NONE', *, *, #8347, .T. ) ; +#7708 = FILL_AREA_STYLE_COLOUR ( '', #45518 ) ; +#7709 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7710 = VECTOR ( 'NONE', #75130, 1000.000000000000114 ) ; +#7711 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42077 ) ) ; +#7712 = PLANE ( 'NONE', #9590 ) ; +#7713 = FILL_AREA_STYLE_COLOUR ( '', #39569 ) ; +#7714 = CARTESIAN_POINT ( 'NONE', ( 0.03349564727623650928, -1.152628822534790043, 0.8299999999999999600 ) ) ; +#7715 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7716 = CLOSED_SHELL ( 'NONE', ( #22406, #78187, #10597, #49431, #41119, #54304, #68230 ) ) ; +#7717 = ORIENTED_EDGE ( 'NONE', *, *, #29939, .F. ) ; +#7718 = SURFACE_STYLE_USAGE ( .BOTH. , #46600 ) ; +#7719 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#7720 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.099999999999999867, 8.599018957360380094E-79 ) ) ; +#7721 = AXIS2_PLACEMENT_3D ( 'NONE', #69405, #39292, #77093 ) ; +#7722 = VERTEX_POINT ( 'NONE', #54099 ) ; +#7723 = CARTESIAN_POINT ( 'NONE', ( 1.151350676535463080, -1.213996294333074211, 0.8099999999998553912 ) ) ; +#7724 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7725 = EDGE_LOOP ( 'NONE', ( #2476, #36379, #46764, #79718 ) ) ; +#7726 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48645 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15625, #47304, #38639 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7728 = FILL_AREA_STYLE_COLOUR ( '', #87016 ) ; +#7729 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7730 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7731 = CARTESIAN_POINT ( 'NONE', ( 0.4933869866146586292, 0.5990590759269652787, 0.8100000000000001643 ) ) ; +#7732 = EDGE_CURVE ( 'NONE', #69748, #20637, #84237, .T. ) ; +#7733 = ORIENTED_EDGE ( 'NONE', *, *, #82998, .T. ) ; +#7734 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37828 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14405, #21612, #22116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7735 = FACE_OUTER_BOUND ( 'NONE', #55638, .T. ) ; +#7736 = LINE ( 'NONE', #63496, #6706 ) ; +#7737 = EDGE_CURVE ( 'NONE', #47287, #25572, #59066, .T. ) ; +#7738 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94180 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9297, #70137, #23703 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7739 = EDGE_LOOP ( 'NONE', ( #66278, #42500, #97826, #97485 ) ) ; +#7740 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7741 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#7742 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051949811, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#7743 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.000000000000000000 ) ) ; +#7744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7745 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7746 = VECTOR ( 'NONE', #12692, 1000.000000000000000 ) ; +#7747 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#7748 = ORIENTED_EDGE ( 'NONE', *, *, #40328, .F. ) ; +#7749 = ORIENTED_EDGE ( 'NONE', *, *, #38455, .F. ) ; +#7750 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7751 = ORIENTED_EDGE ( 'NONE', *, *, #28790, .T. ) ; +#7752 = EDGE_CURVE ( 'NONE', #7270, #51353, #31114, .T. ) ; +#7753 = VERTEX_POINT ( 'NONE', #13205 ) ; +#7754 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7755 = ORIENTED_EDGE ( 'NONE', *, *, #76978, .T. ) ; +#7756 = AXIS2_PLACEMENT_3D ( 'NONE', #99272, #45687, #6365 ) ; +#7757 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7758 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7759 = ORIENTED_EDGE ( 'NONE', *, *, #77674, .F. ) ; +#7760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7761 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7762 = LINE ( 'NONE', #86477, #94796 ) ; +#7763 = ORIENTED_EDGE ( 'NONE', *, *, #21451, .T. ) ; +#7764 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7765 = EDGE_CURVE ( 'NONE', #20028, #56137, #78610, .T. ) ; +#7766 = CARTESIAN_POINT ( 'NONE', ( 1.408848379044900012, -1.435626150595060047, 0.8299999999999999600 ) ) ; +#7767 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#7768 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8991599999999999593 ) ) ; +#7769 = VERTEX_POINT ( 'NONE', #29596 ) ; +#7770 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95890 ), #45292 ) ; +#7771 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#7772 = ORIENTED_EDGE ( 'NONE', *, *, #68108, .F. ) ; +#7773 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7774 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7775 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6745 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18672, #27892, #65661 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7776 = ADVANCED_FACE ( 'NONE', ( #21939 ), #14225, .T. ) ; +#7777 = CARTESIAN_POINT ( 'NONE', ( 0.1542778230595640010, -1.450978309596749893, 0.8299999999999982947 ) ) ; +#7778 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76377 ), #55217 ) ; +#7779 = VERTEX_POINT ( 'NONE', #87244 ) ; +#7780 = ORIENTED_EDGE ( 'NONE', *, *, #44639, .T. ) ; +#7781 = SURFACE_STYLE_USAGE ( .BOTH. , #22699 ) ; +#7782 = CLOSED_SHELL ( 'NONE', ( #16254, #63396, #87452, #50207, #53014, #79455 ) ) ; +#7783 = EDGE_CURVE ( 'NONE', #67521, #2533, #63301, .T. ) ; +#7785 = FACE_OUTER_BOUND ( 'NONE', #26961, .T. ) ; +#7784 = SURFACE_STYLE_USAGE ( .BOTH. , #29360 ) ; +#7786 = FACE_OUTER_BOUND ( 'NONE', #24688, .T. ) ; +#7787 = LINE ( 'NONE', #38525, #32596 ) ; +#7788 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74994 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4662, #91450, #39320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7789 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#7790 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7791 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7792 = EDGE_CURVE ( 'NONE', #68118, #12287, #8537, .T. ) ; +#7793 = LINE ( 'NONE', #70162, #46167 ) ; +#7794 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7795 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97520 ) ) ; +#7796 = LINE ( 'NONE', #79358, #64642 ) ; +#7797 = ORIENTED_EDGE ( 'NONE', *, *, #37050, .T. ) ; +#7798 = CARTESIAN_POINT ( 'NONE', ( -1.188831266068800074, -1.144973971495400145, 0.8300000000000002931 ) ) ; +#7799 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -1.198509146801203521E-79, -0.2999999999999999889 ) ) ; +#7802 = PRESENTATION_STYLE_ASSIGNMENT (( #227 ) ) ; +#7801 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#7800 = SURFACE_SIDE_STYLE ('',( #37551 ) ) ; +#7803 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#7804 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83880, 'distance_accuracy_value', 'NONE'); +#7805 = CARTESIAN_POINT ( 'NONE', ( -0.1289016636980840069, -1.445107798742939931, 0.8299999999999999600 ) ) ; +#7807 = EDGE_CURVE ( 'NONE', #78794, #98020, #71943, .T. ) ; +#7806 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47031 ), #37302 ) ; +#7809 = EDGE_CURVE ( 'NONE', #21700, #3632, #51035, .T. ) ; +#7808 = FILL_AREA_STYLE ('',( #45657 ) ) ; +#7810 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#7811 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#7812 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999999237, -0.1499999999999999944 ) ) ; +#7813 = VERTEX_POINT ( 'NONE', #25493 ) ; +#7814 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#7815 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7816 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#7817 = CYLINDRICAL_SURFACE ( 'NONE', #49812, 1.383450513437169960 ) ; +#7818 = CARTESIAN_POINT ( 'NONE', ( -0.06452060059824049620, -1.437850337629750008, 0.8299999999999999600 ) ) ; +#7819 = EDGE_CURVE ( 'NONE', #61010, #34518, #63982, .T. ) ; +#7820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7821 = VECTOR ( 'NONE', #85645, 1000.000000000000000 ) ; +#7822 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7823 = FACE_OUTER_BOUND ( 'NONE', #76612, .T. ) ; +#7824 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95934 ), #64990 ) ; +#7825 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#7826 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7827 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7828 = EDGE_CURVE ( 'NONE', #14832, #74680, #48478, .T. ) ; +#7829 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7830 = FILL_AREA_STYLE ('',( #83527 ) ) ; +#7831 = STYLED_ITEM ( 'NONE', ( #75979 ), #31644 ) ; +#7832 = FILL_AREA_STYLE_COLOUR ( '', #2796 ) ; +#7833 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#7834 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7835 = ORIENTED_EDGE ( 'NONE', *, *, #77741, .F. ) ; +#7836 = VECTOR ( 'NONE', #3598, 1000.000000000000000 ) ; +#7837 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7838 = LINE ( 'NONE', #1276, #43899 ) ; +#7839 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7840 = FACE_OUTER_BOUND ( 'NONE', #74309, .T. ) ; +#7841 = CARTESIAN_POINT ( 'NONE', ( -5.000849739953540302E-06, 1.393332985365729915, 0.8299999999999999600 ) ) ; +#7842 = SURFACE_SIDE_STYLE ('',( #32436 ) ) ; +#7843 = SURFACE_SIDE_STYLE ('',( #78890 ) ) ; +#7844 = CARTESIAN_POINT ( 'NONE', ( -1.258104321733710007, -1.118172950060400073, 0.8299999999999999600 ) ) ; +#7845 = EDGE_LOOP ( 'NONE', ( #9114, #84797, #43216, #60702 ) ) ; +#7847 = SURFACE_STYLE_USAGE ( .BOTH. , #1284 ) ; +#7846 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51984 ) ) ; +#7848 = FACE_OUTER_BOUND ( 'NONE', #93695, .T. ) ; +#7850 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#7849 = AXIS2_PLACEMENT_3D ( 'NONE', #91406, #76079, #35812 ) ; +#7851 = ORIENTED_EDGE ( 'NONE', *, *, #32648, .T. ) ; +#7852 = FILL_AREA_STYLE_COLOUR ( '', #44218 ) ; +#7853 = SURFACE_STYLE_FILL_AREA ( #32449 ) ; +#7854 = VECTOR ( 'NONE', #86229, 1000.000000000000114 ) ; +#7855 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#7856 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, -0.000000000000000000 ) ) ; +#7857 = VECTOR ( 'NONE', #89687, 1000.000000000000000 ) ; +#7858 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#7859 = LINE ( 'NONE', #61595, #79857 ) ; +#7860 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333316872, -1.899999999999999911, 1.747825839084584091E-76 ) ) ; +#7861 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#7862 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81386 ), #35756 ) ; +#7863 = ORIENTED_EDGE ( 'NONE', *, *, #32807, .T. ) ; +#7864 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7865 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#7866 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83225, 'distance_accuracy_value', 'NONE'); +#7867 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, 3.099999999999992095, 0.000000000000000000 ) ) ; +#7868 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82962 ) ) ; +#7869 = EDGE_CURVE ( 'NONE', #96487, #96771, #86236, .T. ) ; +#7870 = VERTEX_POINT ( 'NONE', #85728 ) ; +#7871 = CARTESIAN_POINT ( 'NONE', ( 8.687142875125045904, 2.261923875125043892, 0.8991599999999999593 ) ) ; +#7872 = ORIENTED_EDGE ( 'NONE', *, *, #34730, .T. ) ; +#7873 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#7874 = AXIS2_PLACEMENT_3D ( 'NONE', #54781, #101, #29735 ) ; +#7875 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7876 = LINE ( 'NONE', #62124, #27285 ) ; +#7877 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#7878 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7879 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #97464, #58257 ) ; +#7880 = DIRECTION ( 'NONE', ( 0.5479224129540782862, 0.8365291563254568796, 0.000000000000000000 ) ) ; +#7881 = STYLED_ITEM ( 'NONE', ( #79861 ), #50235 ) ; +#7882 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12853 ) ) ; +#7883 = ORIENTED_EDGE ( 'NONE', *, *, #81834, .F. ) ; +#7884 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43501, 'distance_accuracy_value', 'NONE'); +#7885 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8199999999999999512 ) ) ; +#7886 = SURFACE_STYLE_USAGE ( .BOTH. , #32482 ) ; +#7887 = FACE_OUTER_BOUND ( 'NONE', #25475, .T. ) ; +#7888 = ORIENTED_EDGE ( 'NONE', *, *, #81285, .F. ) ; +#7889 = EDGE_CURVE ( 'NONE', #21812, #7307, #64277, .T. ) ; +#7890 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8991599999999999593 ) ) ; +#7891 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#7892 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80663 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94174, #24296, #39081 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7894 = ORIENTED_EDGE ( 'NONE', *, *, #47180, .F. ) ; +#7893 = VECTOR ( 'NONE', #47285, 1000.000000000000000 ) ; +#7896 = SURFACE_STYLE_USAGE ( .BOTH. , #71274 ) ; +#7895 = FILL_AREA_STYLE_COLOUR ( '', #94408 ) ; +#7897 = VERTEX_POINT ( 'NONE', #79612 ) ; +#7898 = ORIENTED_EDGE ( 'NONE', *, *, #34282, .F. ) ; +#7899 = CARTESIAN_POINT ( 'NONE', ( 1.363472769114729921, -1.331314275383060020, 0.8100000000000000533 ) ) ; +#7900 = VECTOR ( 'NONE', #69297, 1000.000000000000000 ) ; +#7901 = FILL_AREA_STYLE_COLOUR ( '', #27176 ) ; +#7902 = FILL_AREA_STYLE_COLOUR ( '', #37597 ) ; +#7903 = SURFACE_STYLE_USAGE ( .BOTH. , #77938 ) ; +#7904 = ORIENTED_EDGE ( 'NONE', *, *, #67069, .F. ) ; +#7905 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753240063, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#7906 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#7907 = ORIENTED_EDGE ( 'NONE', *, *, #37251, .F. ) ; +#7908 = FILL_AREA_STYLE ('',( #6903 ) ) ; +#7909 = EDGE_LOOP ( 'NONE', ( #33112, #22930, #88783, #29641, #8238 ) ) ; +#7910 = ORIENTED_EDGE ( 'NONE', *, *, #39897, .T. ) ; +#7912 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7911 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#7913 = ADVANCED_FACE ( 'NONE', ( #80125 ), #10051, .T. ) ; +#7914 = FILL_AREA_STYLE_COLOUR ( '', #28164 ) ; +#7916 = VECTOR ( 'NONE', #673, 1000.000000000000000 ) ; +#7915 = PLANE ( 'NONE', #97413 ) ; +#7917 = SURFACE_STYLE_USAGE ( .BOTH. , #30983 ) ; +#7918 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48390 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24322, #86059, #15588 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7919 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8648700000000000276 ) ) ; +#7920 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7921 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#7922 = CARTESIAN_POINT ( 'NONE', ( -0.03429546097047749681, -1.132325613921520091, 0.8100000000000000533 ) ) ; +#7923 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999667, 0.1900000000000000022 ) ) ; +#7924 = SURFACE_STYLE_FILL_AREA ( #47829 ) ; +#7925 = ORIENTED_EDGE ( 'NONE', *, *, #21345, .F. ) ; +#7927 = FACE_OUTER_BOUND ( 'NONE', #71670, .T. ) ; +#7926 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#7928 = SURFACE_SIDE_STYLE ('',( #100320 ) ) ; +#7929 = PLANE ( 'NONE', #53401 ) ; +#7930 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58649 ), #65097 ) ; +#7932 = EDGE_CURVE ( 'NONE', #93723, #15828, #80624, .T. ) ; +#7931 = LINE ( 'NONE', #55529, #77403 ) ; +#7933 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7934 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#7935 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#7936 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#7937 = VERTEX_POINT ( 'NONE', #10549 ) ; +#7938 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7939 = LINE ( 'NONE', #15660, #62515 ) ; +#7940 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96127 ), #60263 ) ; +#7941 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#7942 = PLANE ( 'NONE', #38079 ) ; +#7943 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7945 = VECTOR ( 'NONE', #64080, 1000.000000000000000 ) ; +#7944 = PLANE ( 'NONE', #44848 ) ; +#7946 = ADVANCED_FACE ( 'NONE', ( #41811 ), #27001, .T. ) ; +#7947 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7948 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#7949 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#7950 = LINE ( 'NONE', #92764, #94420 ) ; +#7951 = SURFACE_SIDE_STYLE ('',( #31532 ) ) ; +#7952 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#7953 = SURFACE_STYLE_FILL_AREA ( #31534 ) ; +#7954 = AXIS2_PLACEMENT_3D ( 'NONE', #81065, #65725, #41248 ) ; +#7955 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7956 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7957 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7958 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999994005, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#7959 = VERTEX_POINT ( 'NONE', #74960 ) ; +#7960 = LINE ( 'NONE', #40223, #23405 ) ; +#7961 = DIRECTION ( 'NONE', ( -4.640777529015779698E-48, -0.000000000000000000, 1.000000000000000000 ) ) ; +#7962 = VECTOR ( 'NONE', #72610, 1000.000000000000000 ) ; +#7963 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68157 ), #19268 ) ; +#7964 = CARTESIAN_POINT ( 'NONE', ( -0.004761740495047140850, -1.264112177694660000, 0.8300000000000002931 ) ) ; +#7965 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#7966 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8865, #32455, #86051, #24821 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#7967 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7968 = CARTESIAN_POINT ( 'NONE', ( 1.840728708308519979, -1.463352833475739967, 0.8300000000000011813 ) ) ; +#7969 = ADVANCED_FACE ( 'NONE', ( #96895 ), #58165, .T. ) ; +#7970 = ORIENTED_EDGE ( 'NONE', *, *, #51139, .T. ) ; +#7971 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#7972 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#7973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#7974 = CARTESIAN_POINT ( 'NONE', ( 1.702517484154870031, -1.219598171061480052, 0.8299999999999994049 ) ) ; +#7975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49400 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44716, #13524, #91688 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#7976 = STYLED_ITEM ( 'NONE', ( #23640 ), #92090 ) ; +#7977 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#7978 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -0.1499999999999999944 ) ) ; +#7979 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7980 = CIRCLE ( 'NONE', #48912, 1.319494420477459906 ) ; +#7981 = EDGE_CURVE ( 'NONE', #86302, #44826, #28012, .T. ) ; +#7982 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#7983 = VECTOR ( 'NONE', #80068, 1000.000000000000000 ) ; +#7984 = ORIENTED_EDGE ( 'NONE', *, *, #28143, .T. ) ; +#7985 = VERTEX_POINT ( 'NONE', #82623 ) ; +#7986 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#7987 = ORIENTED_EDGE ( 'NONE', *, *, #37145, .T. ) ; +#7988 = CARTESIAN_POINT ( 'NONE', ( -0.2912322945111979755, -1.413990021526319918, 0.8299999999999999600 ) ) ; +#7989 = FILL_AREA_STYLE_COLOUR ( '', #80943 ) ; +#7990 = LINE ( 'NONE', #54051, #100031 ) ; +#7991 = SHAPE_DEFINITION_REPRESENTATION ( #33488, #29861 ) ; +#7992 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#7993 = STYLED_ITEM ( 'NONE', ( #25008 ), #64072 ) ; +#7995 = ORIENTED_EDGE ( 'NONE', *, *, #6090, .F. ) ; +#7994 = ORIENTED_EDGE ( 'NONE', *, *, #95570, .T. ) ; +#7996 = VERTEX_POINT ( 'NONE', #59678 ) ; +#7997 = LINE ( 'NONE', #936, #71968 ) ; +#7998 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5205, 'distance_accuracy_value', 'NONE'); +#7999 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8001 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#8000 = LINE ( 'NONE', #92808, #65243 ) ; +#8002 = EDGE_LOOP ( 'NONE', ( #13071, #5918, #27450, #425 ) ) ; +#8003 = FACE_OUTER_BOUND ( 'NONE', #81708, .T. ) ; +#8004 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8005 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44835, #21378, #90326, #76009 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#8007 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#8006 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8008 = VECTOR ( 'NONE', #6943, 1000.000000000000000 ) ; +#8009 = ORIENTED_EDGE ( 'NONE', *, *, #4791, .T. ) ; +#8010 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.449999999999999956, -11.82000000000000028 ) ) ; +#8011 = VERTEX_POINT ( 'NONE', #84613 ) ; +#8012 = ORIENTED_EDGE ( 'NONE', *, *, #30080, .F. ) ; +#8013 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8014 = SURFACE_STYLE_USAGE ( .BOTH. , #85706 ) ; +#8015 = SURFACE_SIDE_STYLE ('',( #40286 ) ) ; +#8017 = VERTEX_POINT ( 'NONE', #91749 ) ; +#8016 = VECTOR ( 'NONE', #94455, 1000.000000000000000 ) ; +#8018 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6700000000000000400, 0.05000000000000000278 ) ) ; +#8019 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45653 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79767, #72575, #9713 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8020 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8991599999999999593 ) ) ; +#8021 = ORIENTED_EDGE ( 'NONE', *, *, #5162, .T. ) ; +#8022 = SURFACE_SIDE_STYLE ('',( #450 ) ) ; +#8023 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8024 = ORIENTED_EDGE ( 'NONE', *, *, #91707, .T. ) ; +#8025 = ORIENTED_EDGE ( 'NONE', *, *, #12768, .F. ) ; +#8026 = EDGE_CURVE ( 'NONE', #80846, #26606, #36172, .T. ) ; +#8027 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#8028 = FILL_AREA_STYLE ('',( #40301 ) ) ; +#8029 = EDGE_CURVE ( 'NONE', #89137, #33578, #98353, .T. ) ; +#8030 = FILL_AREA_STYLE ('',( #79608 ) ) ; +#8031 = VECTOR ( 'NONE', #89938, 1000.000000000000000 ) ; +#8032 = PRESENTATION_STYLE_ASSIGNMENT (( #31111 ) ) ; +#8033 = SURFACE_STYLE_FILL_AREA ( #2501 ) ; +#8034 = CARTESIAN_POINT ( 'NONE', ( 1.316661513406260031, -1.260670644472420054, 0.8299999999999997380 ) ) ; +#8035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86414 ) ) ; +#8036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79244, 'distance_accuracy_value', 'NONE'); +#8037 = LINE ( 'NONE', #54103, #80174 ) ; +#8038 = EDGE_LOOP ( 'NONE', ( #46333, #89203, #52684, #73927 ) ) ; +#8039 = CARTESIAN_POINT ( 'NONE', ( 0.4623821970225030498, -1.113520705134940059, 0.8299999999999999600 ) ) ; +#8040 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8041 = ORIENTED_EDGE ( 'NONE', *, *, #46853, .F. ) ; +#8042 = FILL_AREA_STYLE ('',( #84731 ) ) ; +#8043 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49825 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15753, #79088, #32121 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8044 = PRESENTATION_STYLE_ASSIGNMENT (( #15774 ) ) ; +#8045 = VECTOR ( 'NONE', #64333, 1000.000000000000000 ) ; +#8047 = EDGE_CURVE ( 'NONE', #63404, #63739, #30455, .T. ) ; +#8046 = SURFACE_STYLE_USAGE ( .BOTH. , #15253 ) ; +#8048 = VECTOR ( 'NONE', #45504, 1000.000000000000000 ) ; +#8050 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#8049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35230 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24553, #55680, #54668 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8051 = CARTESIAN_POINT ( 'NONE', ( 1.753807303740889889, -0.9763607356531520676, 0.8100000000000000533 ) ) ; +#8052 = FILL_AREA_STYLE ('',( #45403 ) ) ; +#8053 = LINE ( 'NONE', #55156, #59330 ) ; +#8054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8055 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79893 ) ) ; +#8056 = CYLINDRICAL_SURFACE ( 'NONE', #59127, 0.009999999999999998473 ) ; +#8057 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8058 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#8059 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#8060 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78285 ) ) ; +#8061 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.000000000000000000 ) ) ; +#8062 = ADVANCED_FACE ( 'NONE', ( #67275 ), #13588, .T. ) ; +#8064 = SURFACE_SIDE_STYLE ('',( #69924 ) ) ; +#8063 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.1000000000000020040, 0.8299999999999999600 ) ) ; +#8065 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8066 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81532 ), #50315 ) ; +#8067 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220025313, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#8068 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8069 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19589, #50773, #58942 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8070 = ORIENTED_EDGE ( 'NONE', *, *, #28589, .F. ) ; +#8071 = SURFACE_STYLE_USAGE ( .BOTH. , #24539 ) ; +#8072 = SURFACE_STYLE_FILL_AREA ( #70965 ) ; +#8073 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76086, 'distance_accuracy_value', 'NONE'); +#8074 = ORIENTED_EDGE ( 'NONE', *, *, #20795, .F. ) ; +#8075 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37290, 'distance_accuracy_value', 'NONE'); +#8076 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8100000000000001643 ) ) ; +#8077 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#8078 = CARTESIAN_POINT ( 'NONE', ( 0.4006138012824256300, -1.197427965463691235, 0.8100000000000002753 ) ) ; +#8079 = VECTOR ( 'NONE', #52076, 1000.000000000000000 ) ; +#8080 = LINE ( 'NONE', #32179, #61355 ) ; +#8081 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3167 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26021, #48502, #56159 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8082 = SURFACE_SIDE_STYLE ('',( #46444 ) ) ; +#8083 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8084 = SURFACE_STYLE_FILL_AREA ( #7583 ) ; +#8085 = EDGE_CURVE ( 'NONE', #57652, #6059, #91266, .T. ) ; +#8086 = VERTEX_POINT ( 'NONE', #76442 ) ; +#8087 = FILL_AREA_STYLE_COLOUR ( '', #35184 ) ; +#8088 = ORIENTED_EDGE ( 'NONE', *, *, #35571, .F. ) ; +#8089 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8090 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14172, 'distance_accuracy_value', 'NONE'); +#8091 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100696, 'distance_accuracy_value', 'NONE'); +#8092 = STYLED_ITEM ( 'NONE', ( #65862 ), #44834 ) ; +#8093 = SURFACE_STYLE_USAGE ( .BOTH. , #91443 ) ; +#8094 = FACE_OUTER_BOUND ( 'NONE', #30816, .T. ) ; +#8095 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8096 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.05000000000000000278, 0.08229670385730990245 ) ) ; +#8097 = FILL_AREA_STYLE ('',( #24041 ) ) ; +#8098 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8099 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8100 = ORIENTED_EDGE ( 'NONE', *, *, #15814, .T. ) ; +#8101 = EDGE_CURVE ( 'NONE', #38590, #90724, #53486, .T. ) ; +#8102 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.000000000000000000, 0.3499999999999999778 ) ) ; +#8103 = VERTEX_POINT ( 'NONE', #21321 ) ; +#8104 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8105 = FILL_AREA_STYLE_COLOUR ( '', #48452 ) ; +#8106 = ORIENTED_EDGE ( 'NONE', *, *, #57276, .F. ) ; +#8107 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8108 = CARTESIAN_POINT ( 'NONE', ( 1.067938486522060026, -1.390907012919420094, 0.8299999999999999600 ) ) ; +#8109 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8110 = AXIS2_PLACEMENT_3D ( 'NONE', #85591, #24352, #93214 ) ; +#8111 = AXIS2_PLACEMENT_3D ( 'NONE', #99476, #98973, #28139 ) ; +#8112 = PLANE ( 'NONE', #36137 ) ; +#8113 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8114 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220085265, 2.700000000000000178, 0.000000000000000000 ) ) ; +#8115 = EDGE_CURVE ( 'NONE', #63005, #79825, #20823, .T. ) ; +#8117 = EDGE_LOOP ( 'NONE', ( #87100, #82869, #16368, #16632 ) ) ; +#8116 = EDGE_LOOP ( 'NONE', ( #63061, #99152, #76068, #2101 ) ) ; +#8118 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8119 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#8120 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96232 ) ) ; +#8121 = PLANE ( 'NONE', #80638 ) ; +#8122 = VERTEX_POINT ( 'NONE', #29488 ) ; +#8123 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8124 = VECTOR ( 'NONE', #70886, 1000.000000000000000 ) ; +#8126 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#8125 = FACE_OUTER_BOUND ( 'NONE', #97564, .T. ) ; +#8127 = ORIENTED_EDGE ( 'NONE', *, *, #10233, .F. ) ; +#8128 = ORIENTED_EDGE ( 'NONE', *, *, #31271, .T. ) ; +#8129 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8130 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#8131 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8132 = CARTESIAN_POINT ( 'NONE', ( -0.1271088354660659947, -0.9625852181168450539, 0.8300000000000000711 ) ) ; +#8133 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8134 = VECTOR ( 'NONE', #7325, 1000.000000000000000 ) ; +#8135 = ORIENTED_EDGE ( 'NONE', *, *, #5646, .F. ) ; +#8136 = ORIENTED_EDGE ( 'NONE', *, *, #93953, .F. ) ; +#8137 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#8138 = VERTEX_POINT ( 'NONE', #84113 ) ; +#8139 = ADVANCED_FACE ( 'NONE', ( #60649 ), #52992, .F. ) ; +#8140 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8141 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8142 = ORIENTED_EDGE ( 'NONE', *, *, #4533, .T. ) ; +#8143 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44943 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74109, #73601, #33808 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8144 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#8145 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8146 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000488, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#8147 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#8148 = ORIENTED_EDGE ( 'NONE', *, *, #44249, .F. ) ; +#8149 = LINE ( 'NONE', #55735, #4394 ) ; +#8150 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8151 = EDGE_LOOP ( 'NONE', ( #77056, #99133, #97544, #70748 ) ) ; +#8152 = ADVANCED_FACE ( 'NONE', ( #340 ), #852, .F. ) ; +#8153 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8154 = ADVANCED_FACE ( 'NONE', ( #7426 ), #27992, .T. ) ; +#8155 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8156 = PLANE ( 'NONE', #27375 ) ; +#8157 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21287 ), #1718 ) ; +#8158 = LINE ( 'NONE', #85851, #98574 ) ; +#8159 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78866, #78372, #30885, #62572 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#8160 = EDGE_LOOP ( 'NONE', ( #72377, #40753, #44919, #65256 ) ) ; +#8161 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11383 ) ) ; +#8162 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.600000000000000089, -11.36999999999999922 ) ) ; +#8163 = DIRECTION ( 'NONE', ( 0.7071067811865504593, -0.7071067811865445751, 0.000000000000000000 ) ) ; +#8164 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8165 = FILL_AREA_STYLE ('',( #11060 ) ) ; +#8166 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8167 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8168 = LINE ( 'NONE', #46535, #21855 ) ; +#8169 = ORIENTED_EDGE ( 'NONE', *, *, #98982, .T. ) ; +#8170 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#8172 = EDGE_CURVE ( 'NONE', #85557, #64241, #71309, .T. ) ; +#8171 = LINE ( 'NONE', #39397, #39818 ) ; +#8173 = FACE_OUTER_BOUND ( 'NONE', #44285, .T. ) ; +#8175 = SURFACE_STYLE_FILL_AREA ( #93983 ) ; +#8174 = LINE ( 'NONE', #15897, #73999 ) ; +#8176 = FILL_AREA_STYLE_COLOUR ( '', #33621 ) ; +#8177 = EDGE_CURVE ( 'NONE', #2124, #54748, #63675, .T. ) ; +#8178 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96330 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19693, #57522, #49856 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8179 = STYLED_ITEM ( 'NONE', ( #51799 ), #33659 ) ; +#8180 = FILL_AREA_STYLE ('',( #69525 ) ) ; +#8181 = ORIENTED_EDGE ( 'NONE', *, *, #11878, .F. ) ; +#8182 = SURFACE_SIDE_STYLE ('',( #94526 ) ) ; +#8183 = LINE ( 'NONE', #78236, #82176 ) ; +#8184 = VECTOR ( 'NONE', #22694, 1000.000000000000000 ) ; +#8185 = ORIENTED_EDGE ( 'NONE', *, *, #4777, .F. ) ; +#8186 = ADVANCED_FACE ( 'NONE', ( #40687 ), #38654, .T. ) ; +#8187 = VECTOR ( 'NONE', #46295, 1000.000000000000000 ) ; +#8188 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#8189 = EDGE_CURVE ( 'NONE', #16737, #88228, #64395, .T. ) ; +#8190 = SURFACE_STYLE_USAGE ( .BOTH. , #31253 ) ; +#8191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8192 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#8193 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24423 ), #18021 ) ; +#8194 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19738 ), #31096 ) ; +#8195 = FILL_AREA_STYLE ('',( #78248 ) ) ; +#8196 = ORIENTED_EDGE ( 'NONE', *, *, #86091, .F. ) ; +#8197 = FILL_AREA_STYLE_COLOUR ( '', #1705 ) ; +#8198 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8199 = PLANE ( 'NONE', #49559 ) ; +#8200 = CARTESIAN_POINT ( 'NONE', ( -0.04176633354695089700, -1.139163918933580266, 0.8300000000000005151 ) ) ; +#8201 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#8202 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#8203 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#8204 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#8205 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#8206 = FILL_AREA_STYLE_COLOUR ( '', #96439 ) ; +#8207 = VECTOR ( 'NONE', #81908, 1000.000000000000000 ) ; +#8208 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#8209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8210 = CARTESIAN_POINT ( 'NONE', ( 0.05660856691479519698, -0.9907810524907130212, 0.8100000000000000533 ) ) ; +#8211 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#8212 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33338, 'distance_accuracy_value', 'NONE'); +#8213 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84960 ), #65367 ) ; +#8214 = EDGE_CURVE ( 'NONE', #35923, #41604, #10419, .T. ) ; +#8215 = LINE ( 'NONE', #55790, #50481 ) ; +#8216 = ORIENTED_EDGE ( 'NONE', *, *, #76896, .F. ) ; +#8217 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8218 = ORIENTED_EDGE ( 'NONE', *, *, #37659, .T. ) ; +#8219 = FILL_AREA_STYLE ('',( #62454 ) ) ; +#8221 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11401, 'distance_accuracy_value', 'NONE'); +#8220 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8222 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13066, 'distance_accuracy_value', 'NONE'); +#8223 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8224 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#8225 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8226 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#8227 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#8228 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#8229 = FILL_AREA_STYLE ('',( #60953 ) ) ; +#8230 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#8231 = ORIENTED_EDGE ( 'NONE', *, *, #1542, .T. ) ; +#8232 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, 0.000000000000000000 ) ) ; +#8233 = EDGE_CURVE ( 'NONE', #29642, #63665, #79999, .T. ) ; +#8234 = EDGE_CURVE ( 'NONE', #27995, #79989, #25873, .T. ) ; +#8235 = LINE ( 'NONE', #72615, #56872 ) ; +#8236 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60153, 'distance_accuracy_value', 'NONE'); +#8237 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#8238 = ORIENTED_EDGE ( 'NONE', *, *, #53982, .T. ) ; +#8239 = CARTESIAN_POINT ( 'NONE', ( 1.159211952929653400, -1.215936827035543066, 0.8099999999998542810 ) ) ; +#8240 = PLANE ( 'NONE', #34153 ) ; +#8241 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68578 ) ) ; +#8242 = ORIENTED_EDGE ( 'NONE', *, *, #25187, .F. ) ; +#8243 = FILL_AREA_STYLE ('',( #30265 ) ) ; +#8244 = EDGE_CURVE ( 'NONE', #77034, #14910, #42685, .T. ) ; +#8245 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1017 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7154, #23083, #53220 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8246 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.000000000000000000 ) ) ; +#8247 = LINE ( 'NONE', #47641, #70628 ) ; +#8248 = FILL_AREA_STYLE_COLOUR ( '', #55608 ) ; +#8249 = LINE ( 'NONE', #95074, #66089 ) ; +#8250 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8251 = EDGE_CURVE ( 'NONE', #65920, #80304, #65655, .T. ) ; +#8252 = ORIENTED_EDGE ( 'NONE', *, *, #58817, .T. ) ; +#8253 = STYLED_ITEM ( 'NONE', ( #61602 ), #45200 ) ; +#8254 = LINE ( 'NONE', #71127, #60952 ) ; +#8255 = ORIENTED_EDGE ( 'NONE', *, *, #66993, .T. ) ; +#8256 = LINE ( 'NONE', #15974, #92084 ) ; +#8257 = CARTESIAN_POINT ( 'NONE', ( -1.323820061220085220, 3.099999999999990319, -0.02000000000000000042 ) ) ; +#8258 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8259 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#8260 = ORIENTED_EDGE ( 'NONE', *, *, #75795, .T. ) ; +#8261 = ORIENTED_EDGE ( 'NONE', *, *, #62078, .F. ) ; +#8262 = LINE ( 'NONE', #78309, #56459 ) ; +#8264 = EDGE_CURVE ( 'NONE', #2199, #6547, #41690, .T. ) ; +#8263 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100948 ) ; +#8265 = ORIENTED_EDGE ( 'NONE', *, *, #12403, .F. ) ; +#8266 = EDGE_CURVE ( 'NONE', #64307, #98041, #65660, .T. ) ; +#8267 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8268 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#8269 = ORIENTED_EDGE ( 'NONE', *, *, #766, .T. ) ; +#8271 = ORIENTED_EDGE ( 'NONE', *, *, #90905, .F. ) ; +#8270 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#8272 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67097 ) ) ; +#8273 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, -3.499999999999989786, 0.1829999999999999960 ) ) ; +#8274 = FILL_AREA_STYLE ('',( #56876 ) ) ; +#8275 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000000812, -0.2400000000000000189 ) ) ; +#8276 = ORIENTED_EDGE ( 'NONE', *, *, #65415, .T. ) ; +#8277 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8278 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8279 = VERTEX_POINT ( 'NONE', #58549 ) ; +#8280 = VECTOR ( 'NONE', #59521, 1000.000000000000114 ) ; +#8281 = ADVANCED_FACE ( 'NONE', ( #41189 ), #4367, .T. ) ; +#8282 = SURFACE_STYLE_FILL_AREA ( #61006 ) ; +#8283 = ORIENTED_EDGE ( 'NONE', *, *, #84114, .T. ) ; +#8284 = VECTOR ( 'NONE', #52918, 1000.000000000000000 ) ; +#8285 = SURFACE_SIDE_STYLE ('',( #93088 ) ) ; +#8286 = VERTEX_POINT ( 'NONE', #30331 ) ; +#8287 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8288 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34950 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85254, #7059, #60311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8289 = LINE ( 'NONE', #24748, #16399 ) ; +#8290 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52075 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68213, #29917, #21263 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8291 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#8292 = LINE ( 'NONE', #1750, #61470 ) ; +#8293 = DIRECTION ( 'NONE', ( 7.400903063771439863E-81, -1.000000000000000000, 6.178108703866260351E-129 ) ) ; +#8294 = ORIENTED_EDGE ( 'NONE', *, *, #31508, .T. ) ; +#8296 = PLANE ( 'NONE', #13143 ) ; +#8295 = FACE_OUTER_BOUND ( 'NONE', #45062, .T. ) ; +#8297 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#8298 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15960, 'distance_accuracy_value', 'NONE'); +#8299 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8100000000000000533 ) ) ; +#8300 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8301 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, -11.36999999999999922 ) ) ; +#8302 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886600000000008, 0.8991599999999999593 ) ) ; +#8303 = LINE ( 'NONE', #71182, #458 ) ; +#8304 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8305 = ORIENTED_EDGE ( 'NONE', *, *, #59006, .T. ) ; +#8306 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, -8.400000000000000355, -13.35000000000000142 ) ) ; +#8307 = EDGE_CURVE ( 'NONE', #54713, #28239, #13989, .T. ) ; +#8309 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#8308 = PLANE ( 'NONE', #78357 ) ; +#8310 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#8311 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52438 ) ) ; +#8312 = CARTESIAN_POINT ( 'NONE', ( -0.1561074608318659962, -1.440618065759700084, 0.8299999999999999600 ) ) ; +#8313 = CARTESIAN_POINT ( 'NONE', ( -1.175156004799000176, -1.443574297695930264, 0.8299999999999998490 ) ) ; +#8314 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8315 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8316 = EDGE_CURVE ( 'NONE', #5418, #35668, #96001, .T. ) ; +#8317 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #62751, #42163, #23962, #47407 ), + ( #55607, #73304, #86718, #3348 ), + ( #34515, #50353, #38738, #89612 ), + ( #97242, #27859, #12924, #27336 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#8318 = VERTEX_POINT ( 'NONE', #21195 ) ; +#8319 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#8320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8321 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8991599999999999593 ) ) ; +#8322 = LINE ( 'NONE', #95665, #65792 ) ; +#8323 = SURFACE_STYLE_USAGE ( .BOTH. , #54909 ) ; +#8324 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58975 ), #67084 ) ; +#8325 = CARTESIAN_POINT ( 'NONE', ( 8.231457000000000690, 10.67649499999999918, 0.8648700000000000276 ) ) ; +#8326 = SURFACE_STYLE_FILL_AREA ( #25289 ) ; +#8327 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8328 = FILL_AREA_STYLE ('',( #23755 ) ) ; +#8329 = VECTOR ( 'NONE', #16414, 1000.000000000000000 ) ; +#8330 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#8332 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8333 = ADVANCED_FACE ( 'NONE', ( #83994 ), #5829, .T. ) ; +#8334 = ORIENTED_EDGE ( 'NONE', *, *, #64377, .T. ) ; +#8335 = LINE ( 'NONE', #24286, #8819 ) ; +#8337 = ORIENTED_EDGE ( 'NONE', *, *, #35099, .T. ) ; +#8336 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52460 ), #322 ) ; +#8338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57766, 'distance_accuracy_value', 'NONE'); +#8339 = AXIS2_PLACEMENT_3D ( 'NONE', #38795, #99473, #77089 ) ; +#8340 = CARTESIAN_POINT ( 'NONE', ( -0.8280235389610389740, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#8341 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8342 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8648700000000000276 ) ) ; +#8343 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#8344 = CARTESIAN_POINT ( 'NONE', ( -0.9713447595867019668, -1.214210613447320064, 0.8299999999999999600 ) ) ; +#8345 = ORIENTED_EDGE ( 'NONE', *, *, #62775, .F. ) ; +#8346 = CARTESIAN_POINT ( 'NONE', ( 0.04764703982410237182, -0.9710263181068192750, 0.8100000000002893774 ) ) ; +#8347 = EDGE_CURVE ( 'NONE', #80553, #90724, #12454, .T. ) ; +#8348 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73603 ), #81784 ) ; +#8349 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#8350 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47405, 'distance_accuracy_value', 'NONE'); +#8351 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5121 ) ) ; +#8353 = EDGE_LOOP ( 'NONE', ( #71646, #86645, #43852, #63508 ) ) ; +#8354 = FILL_AREA_STYLE ('',( #7852 ) ) ; +#8355 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70946 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87058, #54927, #2311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8356 = LINE ( 'NONE', #39094, #26076 ) ; +#8357 = DIRECTION ( 'NONE', ( 0.3643423458302801343, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#8358 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.100000000000000089 ) ) ; +#8359 = EDGE_CURVE ( 'NONE', #84177, #71556, #37041, .T. ) ; +#8361 = ORIENTED_EDGE ( 'NONE', *, *, #73754, .T. ) ; +#8360 = STYLED_ITEM ( 'NONE', ( #20658 ), #69970 ) ; +#8362 = LINE ( 'NONE', #93667, #20474 ) ; +#8363 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79178, 'distance_accuracy_value', 'NONE'); +#8364 = LINE ( 'NONE', #285, #27968 ) ; +#8365 = VECTOR ( 'NONE', #8729, 1000.000000000000000 ) ; +#8366 = ADVANCED_FACE ( 'NONE', ( #91630, #21695 ), #13458, .F. ) ; +#8367 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8368 = ORIENTED_EDGE ( 'NONE', *, *, #60543, .F. ) ; +#8369 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8370 = ORIENTED_EDGE ( 'NONE', *, *, #97914, .T. ) ; +#8372 = LINE ( 'NONE', #17613, #86845 ) ; +#8371 = VECTOR ( 'NONE', #52275, 1000.000000000000000 ) ; +#8373 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#8374 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#8375 = ADVANCED_FACE ( 'NONE', ( #77830 ), #30855, .T. ) ; +#8376 = EDGE_CURVE ( 'NONE', #40310, #86354, #85993, .T. ) ; +#8377 = PLANE ( 'NONE', #5640 ) ; +#8378 = ADVANCED_FACE ( 'NONE', ( #26136 ), #14990, .T. ) ; +#8379 = ORIENTED_EDGE ( 'NONE', *, *, #22188, .F. ) ; +#8380 = EDGE_CURVE ( 'NONE', #7753, #51096, #94120, .T. ) ; +#8381 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8382 = FILL_AREA_STYLE ('',( #16105 ) ) ; +#8384 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8383 = PRESENTATION_STYLE_ASSIGNMENT (( #78424 ) ) ; +#8385 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#8386 = ORIENTED_EDGE ( 'NONE', *, *, #64398, .F. ) ; +#8387 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.000000000000000000 ) ) ; +#8388 = ADVANCED_FACE ( 'NONE', ( #57281 ), #77315, .F. ) ; +#8389 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42746 ), #31293 ) ; +#8390 = AXIS2_PLACEMENT_3D ( 'NONE', #33606, #95847, #40760 ) ; +#8391 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8392 = ORIENTED_EDGE ( 'NONE', *, *, #21917, .F. ) ; +#8393 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#8394 = ORIENTED_EDGE ( 'NONE', *, *, #7448, .F. ) ; +#8395 = ORIENTED_EDGE ( 'NONE', *, *, #10067, .F. ) ; +#8396 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8397 = EDGE_CURVE ( 'NONE', #46291, #37746, #59313, .T. ) ; +#8398 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54121 ), #62302 ) ; +#8399 = VECTOR ( 'NONE', #85140, 1000.000000000000114 ) ; +#8401 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8400 = SURFACE_STYLE_FILL_AREA ( #830 ) ; +#8402 = SURFACE_SIDE_STYLE ('',( #79471 ) ) ; +#8403 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #75506, #85938 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #93684 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#8404 = ORIENTED_EDGE ( 'NONE', *, *, #97864, .F. ) ; +#8405 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8406 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8407 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8408 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.5000000000000017764, 0.8299999999999999600 ) ) ; +#8409 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999999556, 3.123820061220045297, -0.02000000000000000042 ) ) ; +#8410 = ORIENTED_EDGE ( 'NONE', *, *, #962, .F. ) ; +#8411 = CARTESIAN_POINT ( 'NONE', ( -0.1408076298701300133, -1.164935064935070042, 0.8100000000000000533 ) ) ; +#8412 = ORIENTED_EDGE ( 'NONE', *, *, #49193, .F. ) ; +#8413 = VERTEX_POINT ( 'NONE', #36792 ) ; +#8414 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.000000000000000000 ) ) ; +#8415 = LINE ( 'NONE', #49334, #45690 ) ; +#8416 = FILL_AREA_STYLE_COLOUR ( '', #53027 ) ; +#8417 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86798 ), #33011 ) ; +#8419 = PLANE ( 'NONE', #86700 ) ; +#8420 = CARTESIAN_POINT ( 'NONE', ( -0.05867698335161790346, -1.150470459123589917, 0.8299999999999999600 ) ) ; +#8421 = FACE_OUTER_BOUND ( 'NONE', #59600, .T. ) ; +#8422 = STYLED_ITEM ( 'NONE', ( #99007 ), #25691 ) ; +#8423 = ORIENTED_EDGE ( 'NONE', *, *, #9836, .F. ) ; +#8424 = SURFACE_STYLE_FILL_AREA ( #61163 ) ; +#8425 = EDGE_CURVE ( 'NONE', #97223, #87078, #12728, .T. ) ; +#8426 = STYLED_ITEM ( 'NONE', ( #26227 ), #70081 ) ; +#8428 = FILL_AREA_STYLE ('',( #23352 ) ) ; +#8427 = FILL_AREA_STYLE ('',( #68768 ) ) ; +#8429 = PLANE ( 'NONE', #72943 ) ; +#8430 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8431 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#8432 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8433 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37827 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68454, #90445, #6122 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8434 = ADVANCED_FACE ( 'NONE', ( #52129 ), #36303, .T. ) ; +#8435 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8436 = ORIENTED_EDGE ( 'NONE', *, *, #63922, .F. ) ; +#8437 = PRESENTATION_STYLE_ASSIGNMENT (( #47334 ) ) ; +#8438 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8439 = AXIS2_PLACEMENT_3D ( 'NONE', #64793, #51528, #95911 ) ; +#8440 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8441 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75616 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2668, #85145, #75007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8442 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79105, 'distance_accuracy_value', 'NONE'); +#8443 = SURFACE_STYLE_USAGE ( .BOTH. , #87163 ) ; +#8444 = FACE_OUTER_BOUND ( 'NONE', #73322, .T. ) ; +#8445 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8446 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8447 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#8448 = FACE_OUTER_BOUND ( 'NONE', #40583, .T. ) ; +#8449 = FACE_OUTER_BOUND ( 'NONE', #2216, .T. ) ; +#8450 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.164662551751850073, 0.8100000000000000533 ) ) ; +#8451 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49300 ), #63951 ) ; +#8453 = VECTOR ( 'NONE', #56732, 1000.000000000000000 ) ; +#8452 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8454 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8455 = SURFACE_STYLE_USAGE ( .BOTH. , #78492 ) ; +#8456 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#8457 = VECTOR ( 'NONE', #96672, 1000.000000000000000 ) ; +#8458 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #7062, 'design' ) ; +#8459 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#8460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8461 = ORIENTED_EDGE ( 'NONE', *, *, #100555, .T. ) ; +#8462 = EDGE_CURVE ( 'NONE', #44849, #1838, #51640, .T. ) ; +#8463 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96578 ), #59340 ) ; +#8464 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8465 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87125, 'distance_accuracy_value', 'NONE'); +#8466 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8468 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8467 = SURFACE_STYLE_FILL_AREA ( #87681 ) ; +#8469 = CARTESIAN_POINT ( 'NONE', ( 1.060290849842712824, -1.038601119630429448, 0.8099999999999657474 ) ) ; +#8470 = STYLED_ITEM ( 'NONE', ( #38400 ), #60271 ) ; +#8471 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72764, #89097, #3321, #50327 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#8472 = STYLED_ITEM ( 'NONE', ( #69695 ), #96229 ) ; +#8473 = SURFACE_SIDE_STYLE ('',( #38701 ) ) ; +#8474 = LINE ( 'NONE', #24427, #58164 ) ; +#8475 = ORIENTED_EDGE ( 'NONE', *, *, #18197, .F. ) ; +#8476 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39619 ) ) ; +#8477 = SURFACE_SIDE_STYLE ('',( #48904 ) ) ; +#8478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99971 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74351, #73847, #88164 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8479 = CARTESIAN_POINT ( 'NONE', ( 1.788063499344580087, -1.247965265924660061, 0.8299999999999994049 ) ) ; +#8480 = LINE ( 'NONE', #39718, #17736 ) ; +#8481 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58150, 'distance_accuracy_value', 'NONE'); +#8482 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8483 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54977, 'distance_accuracy_value', 'NONE'); +#8484 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8485 = PLANE ( 'NONE', #22453 ) ; +#8486 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44414 ), #65651 ) ; +#8487 = ORIENTED_EDGE ( 'NONE', *, *, #67533, .T. ) ; +#8488 = ORIENTED_EDGE ( 'NONE', *, *, #68714, .F. ) ; +#8489 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.188311688311689984, 0.8100000000000000533 ) ) ; +#8490 = STYLED_ITEM ( 'NONE', ( #55057 ), #66915 ) ; +#8491 = ORIENTED_EDGE ( 'NONE', *, *, #99861, .T. ) ; +#8492 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#8493 = FACE_OUTER_BOUND ( 'NONE', #94449, .T. ) ; +#8494 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8495 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22732, 'distance_accuracy_value', 'NONE'); +#8496 = PRODUCT_CONTEXT ( 'NONE', #24794, 'mechanical' ) ; +#8498 = ORIENTED_EDGE ( 'NONE', *, *, #22188, .T. ) ; +#8497 = ORIENTED_EDGE ( 'NONE', *, *, #84470, .F. ) ; +#8499 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36308 ) ) ; +#8500 = ORIENTED_EDGE ( 'NONE', *, *, #96381, .T. ) ; +#8501 = ADVANCED_FACE ( 'NONE', ( #35320 ), #13221, .T. ) ; +#8502 = SURFACE_SIDE_STYLE ('',( #45845 ) ) ; +#8503 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#8504 = EDGE_LOOP ( 'NONE', ( #87988, #83937, #93338, #552 ) ) ; +#8505 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72235 ) ) ; +#8506 = LINE ( 'NONE', #26461, #79983 ) ; +#8507 = ORIENTED_EDGE ( 'NONE', *, *, #86778, .T. ) ; +#8508 = LINE ( 'NONE', #85189, #69256 ) ; +#8509 = EDGE_LOOP ( 'NONE', ( #3515, #19659, #8500, #92880 ) ) ; +#8511 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8510 = FILL_AREA_STYLE ('',( #78547 ) ) ; +#8512 = VECTOR ( 'NONE', #31475, 1000.000000000000114 ) ; +#8513 = ORIENTED_EDGE ( 'NONE', *, *, #36305, .F. ) ; +#8514 = EDGE_LOOP ( 'NONE', ( #60875, #63192, #16495, #84074 ) ) ; +#8515 = LINE ( 'NONE', #32113, #435 ) ; +#8516 = EDGE_CURVE ( 'NONE', #33857, #61734, #52627, .T. ) ; +#8517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48282 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27884, #51358, #81518 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8518 = SURFACE_STYLE_USAGE ( .BOTH. , #8015 ) ; +#8519 = ORIENTED_EDGE ( 'NONE', *, *, #6898, .F. ) ; +#8520 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000927, 0.2500000000000000000 ) ) ; +#8521 = LINE ( 'NONE', #70912, #19760 ) ; +#8522 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8523 = VERTEX_POINT ( 'NONE', #78104 ) ; +#8525 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 10.67649499999999918, 0.8648700000000000276 ) ) ; +#8524 = LINE ( 'NONE', #38758, #5916 ) ; +#8526 = SURFACE_STYLE_FILL_AREA ( #100903 ) ; +#8527 = ORIENTED_EDGE ( 'NONE', *, *, #67503, .T. ) ; +#8528 = VERTEX_POINT ( 'NONE', #83758 ) ; +#8529 = SURFACE_STYLE_FILL_AREA ( #56128 ) ; +#8530 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83643 ), #16762 ) ; +#8531 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98203 ) ) ; +#8532 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8533 = CARTESIAN_POINT ( 'NONE', ( -0.4387205553799810032, -1.232805253472390117, 0.8299999999999999600 ) ) ; +#8534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13439 ), #98283 ) ; +#8535 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8536 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74750 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80178, #34226, #11117 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8537 = LINE ( 'NONE', #1494, #57524 ) ; +#8538 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8539 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21682 ) ) ; +#8540 = EDGE_CURVE ( 'NONE', #76102, #100385, #30593, .T. ) ; +#8541 = DIRECTION ( 'NONE', ( 0.7071072811858623020, 0.7071062811868792375, 0.000000000000000000 ) ) ; +#8542 = ORIENTED_EDGE ( 'NONE', *, *, #63405, .F. ) ; +#8543 = CARTESIAN_POINT ( 'NONE', ( -0.9119271331630629529, -1.344945484192040075, 0.8100000000000000533 ) ) ; +#8544 = VERTEX_POINT ( 'NONE', #69913 ) ; +#8545 = FILL_AREA_STYLE ('',( #47449 ) ) ; +#8546 = LINE ( 'NONE', #39793, #30074 ) ; +#8547 = STYLED_ITEM ( 'NONE', ( #9466 ), #8981 ) ; +#8548 = FILL_AREA_STYLE ('',( #17799 ) ) ; +#8549 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#8550 = SURFACE_STYLE_USAGE ( .BOTH. , #56145 ) ; +#8552 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8551 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#8553 = CARTESIAN_POINT ( 'NONE', ( 9.535670999999998898, 9.417844000000002325, 0.8648700000000000276 ) ) ; +#8554 = CARTESIAN_POINT ( 'NONE', ( 5.929425875125043710, 2.417487124874956095, 0.8991599999999999593 ) ) ; +#8556 = EDGE_CURVE ( 'NONE', #63260, #80708, #68898, .T. ) ; +#8555 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76021, 'distance_accuracy_value', 'NONE'); +#8557 = FILL_AREA_STYLE ('',( #63322 ) ) ; +#8558 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.000000000000000000 ) ) ; +#8559 = CARTESIAN_POINT ( 'NONE', ( -1.269090901571400032, -0.9900689134305360461, 0.8299999999999998490 ) ) ; +#8560 = STYLED_ITEM ( 'NONE', ( #70733 ), #67137 ) ; +#8561 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#8562 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#8563 = SURFACE_STYLE_USAGE ( .BOTH. , #8064 ) ; +#8564 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8565 = VECTOR ( 'NONE', #60160, 1000.000000000000000 ) ; +#8566 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#8567 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30260, 'distance_accuracy_value', 'NONE'); +#8568 = ORIENTED_EDGE ( 'NONE', *, *, #76927, .F. ) ; +#8569 = LINE ( 'NONE', #15278, #93208 ) ; +#8570 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#8571 = ORIENTED_EDGE ( 'NONE', *, *, #94780, .F. ) ; +#8572 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#8573 = ADVANCED_FACE ( 'NONE', ( #84257 ), #7052, .F. ) ; +#8574 = SURFACE_STYLE_FILL_AREA ( #78615 ) ; +#8575 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#8576 = STYLED_ITEM ( 'NONE', ( #16925 ), #88055 ) ; +#8577 = FACE_OUTER_BOUND ( 'NONE', #69839, .T. ) ; +#8578 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000057288, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#8579 = FILL_AREA_STYLE_COLOUR ( '', #39120 ) ; +#8580 = PRESENTATION_STYLE_ASSIGNMENT (( #1436 ) ) ; +#8582 = EDGE_CURVE ( 'NONE', #19915, #15985, #38306, .T. ) ; +#8581 = VECTOR ( 'NONE', #74752, 1000.000000000000000 ) ; +#8583 = STYLED_ITEM ( 'NONE', ( #9508 ), #25929 ) ; +#8584 = ORIENTED_EDGE ( 'NONE', *, *, #96401, .F. ) ; +#8585 = SURFACE_STYLE_FILL_AREA ( #71992 ) ; +#8586 = VECTOR ( 'NONE', #27255, 1000.000000000000114 ) ; +#8587 = ORIENTED_EDGE ( 'NONE', *, *, #17921, .T. ) ; +#8588 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#8589 = FILL_AREA_STYLE_COLOUR ( '', #33614 ) ; +#8590 = FACE_OUTER_BOUND ( 'NONE', #10777, .T. ) ; +#8591 = SURFACE_STYLE_USAGE ( .BOTH. , #31171 ) ; +#8592 = STYLED_ITEM ( 'NONE', ( #47720 ), #19621 ) ; +#8593 = LINE ( 'NONE', #79153, #4457 ) ; +#8594 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31506 ) ) ; +#8595 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8596 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8597 = ORIENTED_EDGE ( 'NONE', *, *, #40116, .F. ) ; +#8598 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11890 ) ) ; +#8599 = EDGE_CURVE ( 'NONE', #40171, #30669, #91898, .T. ) ; +#8600 = LINE ( 'NONE', #61839, #90833 ) ; +#8601 = EDGE_CURVE ( 'NONE', #94098, #12048, #29614, .T. ) ; +#8602 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -7.018111866568259778E-13 ) ) ; +#8603 = VERTEX_POINT ( 'NONE', #37792 ) ; +#8604 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#8605 = VECTOR ( 'NONE', #68090, 999.9999999999998863 ) ; +#8606 = VECTOR ( 'NONE', #78100, 1000.000000000000000 ) ; +#8607 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8608 = ORIENTED_EDGE ( 'NONE', *, *, #23191, .T. ) ; +#8609 = VECTOR ( 'NONE', #3998, 1000.000000000000000 ) ; +#8610 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#8611 = STYLED_ITEM ( 'NONE', ( #69116 ), #37094 ) ; +#8612 = SURFACE_STYLE_USAGE ( .BOTH. , #71506 ) ; +#8613 = STYLED_ITEM ( 'NONE', ( #82674 ), #96937 ) ; +#8614 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8615 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8616 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, -3.500000000000000444, 0.000000000000000000 ) ) ; +#8618 = ORIENTED_EDGE ( 'NONE', *, *, #17600, .F. ) ; +#8617 = ORIENTED_EDGE ( 'NONE', *, *, #97652, .T. ) ; +#8619 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#8620 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#8621 = SURFACE_SIDE_STYLE ('',( #16337 ) ) ; +#8622 = ORIENTED_EDGE ( 'NONE', *, *, #55692, .F. ) ; +#8623 = EDGE_CURVE ( 'NONE', #44592, #92656, #6575, .T. ) ; +#8624 = SURFACE_SIDE_STYLE ('',( #54183 ) ) ; +#8626 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#8625 = SURFACE_STYLE_FILL_AREA ( #36362 ) ; +#8627 = EDGE_LOOP ( 'NONE', ( #34639, #39214, #68743, #17908 ) ) ; +#8628 = ORIENTED_EDGE ( 'NONE', *, *, #70015, .F. ) ; +#8629 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8630 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70669 ), #99931 ) ; +#8633 = PRESENTATION_STYLE_ASSIGNMENT (( #48571 ) ) ; +#8632 = FILL_AREA_STYLE_COLOUR ( '', #12097 ) ; +#8634 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#8635 = EDGE_LOOP ( 'NONE', ( #20778, #4059, #82341, #77530, #21659, #52596, #1062, #66513 ) ) ; +#8636 = ORIENTED_EDGE ( 'NONE', *, *, #83869, .F. ) ; +#8637 = SURFACE_SIDE_STYLE ('',( #40403 ) ) ; +#8638 = ORIENTED_EDGE ( 'NONE', *, *, #92913, .F. ) ; +#8639 = ADVANCED_FACE ( 'NONE', ( #14250 ), #8056, .T. ) ; +#8640 = VECTOR ( 'NONE', #21810, 1000.000000000000000 ) ; +#8642 = ORIENTED_EDGE ( 'NONE', *, *, #71061, .T. ) ; +#8641 = SURFACE_STYLE_USAGE ( .BOTH. , #26098 ) ; +#8643 = FILL_AREA_STYLE ('',( #94492 ) ) ; +#8644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8645 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5278, #84429, #98174 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8646 = EDGE_LOOP ( 'NONE', ( #4439, #40157, #5045, #4687 ) ) ; +#8647 = FILL_AREA_STYLE_COLOUR ( '', #20727 ) ; +#8648 = ORIENTED_EDGE ( 'NONE', *, *, #96393, .T. ) ; +#8649 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8650 = SURFACE_STYLE_USAGE ( .BOTH. , #9676 ) ; +#8651 = AXIS2_PLACEMENT_3D ( 'NONE', #29733, #100077, #53242 ) ; +#8652 = PLANE ( 'NONE', #18771 ) ; +#8653 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8654 = STYLED_ITEM ( 'NONE', ( #30653 ), #26353 ) ; +#8656 = EDGE_LOOP ( 'NONE', ( #21890, #25451, #8276, #84440 ) ) ; +#8655 = LINE ( 'NONE', #16371, #23297 ) ; +#8657 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.899999999999996136, 2.990963115645192065E-79 ) ) ; +#8658 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#8660 = FACE_OUTER_BOUND ( 'NONE', #25689, .T. ) ; +#8659 = LINE ( 'NONE', #63422, #20293 ) ; +#8661 = EDGE_CURVE ( 'NONE', #61128, #4099, #80325, .T. ) ; +#8662 = CARTESIAN_POINT ( 'NONE', ( 1.667677657188980200, -0.9647878283071119609, 0.8299999999999990719 ) ) ; +#8663 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.449999999999999956, 0.000000000000000000 ) ) ; +#8664 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52794 ), #56087 ) ; +#8665 = CARTESIAN_POINT ( 'NONE', ( 1.748219681435579931, -1.226312279485590295, 0.8099999999999996092 ) ) ; +#8666 = VERTEX_POINT ( 'NONE', #49487 ) ; +#8667 = SURFACE_STYLE_FILL_AREA ( #47566 ) ; +#8668 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8669 = CYLINDRICAL_SURFACE ( 'NONE', #25516, 1.200973049130430015 ) ; +#8670 = CARTESIAN_POINT ( 'NONE', ( 1.332631013682762378, -0.9895216834027915631, 0.8099999999999962785 ) ) ; +#8671 = VECTOR ( 'NONE', #32674, 1000.000000000000000 ) ; +#8672 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8673 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000008, 0.8648700000000000276 ) ) ; +#8675 = VECTOR ( 'NONE', #2784, 1000.000000000000000 ) ; +#8674 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8676 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8677 = EDGE_CURVE ( 'NONE', #82682, #33225, #38809, .T. ) ; +#8679 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92624 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65671, #50395, #81538 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8678 = VECTOR ( 'NONE', #16349, 1000.000000000000000 ) ; +#8680 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72422 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5468, #59693, #75964 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8681 = PRESENTATION_STYLE_ASSIGNMENT (( #92501 ) ) ; +#8682 = ORIENTED_EDGE ( 'NONE', *, *, #32240, .F. ) ; +#8683 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8684 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8686 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #603 ), #70730 ) ; +#8685 = PRESENTATION_STYLE_ASSIGNMENT (( #69530 ) ) ; +#8687 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54430 ), #604 ) ; +#8688 = ORIENTED_EDGE ( 'NONE', *, *, #43678, .T. ) ; +#8689 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8690 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.383333333333333304, 0.000000000000000000 ) ) ; +#8691 = PRESENTATION_STYLE_ASSIGNMENT (( #92995 ) ) ; +#8692 = VECTOR ( 'NONE', #61012, 1000.000000000000114 ) ; +#8693 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#8694 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52630, 'distance_accuracy_value', 'NONE'); +#8695 = ORIENTED_EDGE ( 'NONE', *, *, #79626, .T. ) ; +#8696 = LINE ( 'NONE', #38931, #68497 ) ; +#8697 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626904549, -0.1400000000000000411 ) ) ; +#8698 = FACE_OUTER_BOUND ( 'NONE', #46387, .T. ) ; +#8699 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#8700 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#8701 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8702 = FILL_AREA_STYLE ('',( #78735 ) ) ; +#8703 = FILL_AREA_STYLE ('',( #18456 ) ) ; +#8704 = LINE ( 'NONE', #45536, #76215 ) ; +#8705 = STYLED_ITEM ( 'NONE', ( #96739 ), #72270 ) ; +#8706 = CARTESIAN_POINT ( 'NONE', ( 0.005160739295680100321, -0.9302426320460139841, 0.8299999999999999600 ) ) ; +#8707 = EDGE_CURVE ( 'NONE', #71441, #50949, #80642, .T. ) ; +#8708 = EDGE_CURVE ( 'NONE', #10501, #59891, #71452, .T. ) ; +#8709 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8710 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.699999999999999734, 0.000000000000000000 ) ) ; +#8711 = ORIENTED_EDGE ( 'NONE', *, *, #80692, .T. ) ; +#8712 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#8713 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10316 ), #33247 ) ; +#8714 = VERTEX_POINT ( 'NONE', #63806 ) ; +#8715 = FACE_OUTER_BOUND ( 'NONE', #86440, .T. ) ; +#8716 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#8717 = PLANE ( 'NONE', #28366 ) ; +#8718 = SURFACE_STYLE_USAGE ( .BOTH. , #55800 ) ; +#8719 = PRESENTATION_STYLE_ASSIGNMENT (( #78755 ) ) ; +#8720 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8721 = SURFACE_STYLE_FILL_AREA ( #639 ) ; +#8722 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23476 ), #15255 ) ; +#8723 = PRESENTATION_STYLE_ASSIGNMENT (( #31796 ) ) ; +#8724 = ORIENTED_EDGE ( 'NONE', *, *, #66820, .F. ) ; +#8725 = SURFACE_STYLE_FILL_AREA ( #22125 ) ; +#8726 = EDGE_CURVE ( 'NONE', #100078, #18135, #55653, .T. ) ; +#8727 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#8728 = ADVANCED_FACE ( 'NONE', ( #88285 ), #1513, .T. ) ; +#8729 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8730 = EDGE_LOOP ( 'NONE', ( #95233, #64123, #95578, #22026 ) ) ; +#8731 = LINE ( 'NONE', #39978, #86900 ) ; +#8732 = EDGE_LOOP ( 'NONE', ( #79219, #22698, #30075, #69650 ) ) ; +#8733 = AXIS2_PLACEMENT_3D ( 'NONE', #30630, #62331, #39318 ) ; +#8734 = AXIS2_PLACEMENT_3D ( 'NONE', #82688, #61231, #12667 ) ; +#8735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8736 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#8737 = SURFACE_SIDE_STYLE ('',( #48666 ) ) ; +#8738 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8739 = VECTOR ( 'NONE', #74831, 1000.000000000000000 ) ; +#8740 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#8741 = SURFACE_STYLE_USAGE ( .BOTH. , #53789 ) ; +#8742 = ORIENTED_EDGE ( 'NONE', *, *, #96355, .T. ) ; +#8743 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8744 = EDGE_CURVE ( 'NONE', #42861, #25863, #53471, .T. ) ; +#8745 = LINE ( 'NONE', #32833, #75311 ) ; +#8746 = VECTOR ( 'NONE', #41596, 1000.000000000000000 ) ; +#8747 = ORIENTED_EDGE ( 'NONE', *, *, #42596, .T. ) ; +#8749 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8748 = VECTOR ( 'NONE', #49570, 1000.000000000000000 ) ; +#8750 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 4.849935000000000329, 0.8648700000000000276 ) ) ; +#8751 = SURFACE_SIDE_STYLE ('',( #78788 ) ) ; +#8752 = STYLED_ITEM ( 'NONE', ( #62814 ), #98201 ) ; +#8753 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#8754 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.000000000000000000, -13.25000000000000000 ) ) ; +#8755 = ORIENTED_EDGE ( 'NONE', *, *, #24276, .T. ) ; +#8756 = ORIENTED_EDGE ( 'NONE', *, *, #8761, .T. ) ; +#8757 = SURFACE_STYLE_USAGE ( .BOTH. , #39486 ) ; +#8758 = STYLED_ITEM ( 'NONE', ( #69394 ), #61377 ) ; +#8759 = ORIENTED_EDGE ( 'NONE', *, *, #34120, .F. ) ; +#8760 = VECTOR ( 'NONE', #98533, 1000.000000000000000 ) ; +#8761 = EDGE_CURVE ( 'NONE', #61497, #1951, #64790, .T. ) ; +#8762 = EDGE_CURVE ( 'NONE', #34472, #58260, #2310, .T. ) ; +#8763 = AXIS2_PLACEMENT_3D ( 'NONE', #23954, #39747, #24463 ) ; +#8764 = ORIENTED_EDGE ( 'NONE', *, *, #71988, .F. ) ; +#8766 = ORIENTED_EDGE ( 'NONE', *, *, #19861, .F. ) ; +#8765 = LINE ( 'NONE', #8270, #62380 ) ; +#8767 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15301 ), #72404 ) ; +#8768 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#8769 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8770 = STYLED_ITEM ( 'NONE', ( #76530 ), #68746 ) ; +#8771 = ORIENTED_EDGE ( 'NONE', *, *, #3176, .F. ) ; +#8772 = PLANE ( 'NONE', #89559 ) ; +#8773 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8774 = LINE ( 'NONE', #16489, #50829 ) ; +#8775 = ORIENTED_EDGE ( 'NONE', *, *, #367, .F. ) ; +#8776 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #95598 ) ) ; +#8777 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#8778 = STYLED_ITEM ( 'NONE', ( #68828 ), #68045 ) ; +#8779 = VERTEX_POINT ( 'NONE', #93865 ) ; +#8780 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#8781 = VERTEX_POINT ( 'NONE', #12603 ) ; +#8782 = STYLED_ITEM ( 'NONE', ( #50838 ), #72371 ) ; +#8784 = FILL_AREA_STYLE ('',( #23204 ) ) ; +#8783 = FILL_AREA_STYLE_COLOUR ( '', #12059 ) ; +#8785 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000452, 0.8648700000000000276 ) ) ; +#8786 = ADVANCED_FACE ( 'NONE', ( #28025 ), #34186, .F. ) ; +#8787 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#8788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70834 ) ) ; +#8789 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8790 = ORIENTED_EDGE ( 'NONE', *, *, #97986, .F. ) ; +#8791 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.03333333333333517862, 0.000000000000000000 ) ) ; +#8793 = FILL_AREA_STYLE_COLOUR ( '', #67013 ) ; +#8792 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8794 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.383333333333333304, 0.000000000000000000 ) ) ; +#8795 = EDGE_CURVE ( 'NONE', #13051, #43496, #35192, .T. ) ; +#8796 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#8797 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24329, #57357, #80837 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8798 = VECTOR ( 'NONE', #13476, 1000.000000000000000 ) ; +#8799 = PLANE ( 'NONE', #37875 ) ; +#8801 = ADVANCED_FACE ( 'NONE', ( #97891 ), #88784, .T. ) ; +#8800 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#8803 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33337 ), #61031 ) ; +#8802 = LINE ( 'NONE', #78351, #49620 ) ; +#8804 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85561 ), #79024 ) ; +#8805 = FILL_AREA_STYLE ('',( #16026 ) ) ; +#8806 = SURFACE_STYLE_FILL_AREA ( #16027 ) ; +#8807 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#8808 = SURFACE_SIDE_STYLE ('',( #47704 ) ) ; +#8809 = ORIENTED_EDGE ( 'NONE', *, *, #31535, .T. ) ; +#8810 = SURFACE_STYLE_USAGE ( .BOTH. , #17044 ) ; +#8811 = SURFACE_STYLE_USAGE ( .BOTH. , #2270 ) ; +#8812 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57863 ) ) ; +#8813 = EDGE_CURVE ( 'NONE', #78286, #76960, #4501, .T. ) ; +#8815 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 1.696237999999999913, 0.8991599999999999593 ) ) ; +#8814 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#8816 = FACE_OUTER_BOUND ( 'NONE', #89259, .T. ) ; +#8817 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36181, 'distance_accuracy_value', 'NONE'); +#8818 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, 0.6500000000000000222 ) ) ; +#8819 = VECTOR ( 'NONE', #47737, 1000.000000000000000 ) ; +#8820 = FILL_AREA_STYLE_COLOUR ( '', #96553 ) ; +#8821 = FILL_AREA_STYLE ('',( #48749 ) ) ; +#8822 = ORIENTED_EDGE ( 'NONE', *, *, #72110, .T. ) ; +#8823 = FILL_AREA_STYLE ('',( #31387 ) ) ; +#8824 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, -3.099999999999995204, -0.02000000000000000042 ) ) ; +#8825 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8827 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54895 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54095, #31110, #86231 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8826 = SURFACE_STYLE_FILL_AREA ( #94150 ) ; +#8828 = SURFACE_STYLE_FILL_AREA ( #86014 ) ; +#8829 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67909 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60671, #22339, #5476 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8830 = FILL_AREA_STYLE_COLOUR ( '', #77899 ) ; +#8831 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.000000000000000000 ) ) ; +#8832 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 7.678360999999999770, 0.8648700000000000276 ) ) ; +#8833 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8834 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#8835 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4849999999999999867, 0.2400000000000000189 ) ) ; +#8836 = EDGE_CURVE ( 'NONE', #15546, #85680, #20328, .T. ) ; +#8837 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#8838 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8839 = SURFACE_SIDE_STYLE ('',( #56939 ) ) ; +#8840 = CARTESIAN_POINT ( 'NONE', ( 1.058713228792119931, -1.379057077391790287, 0.8299999999999999600 ) ) ; +#8841 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#8842 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#8843 = ORIENTED_EDGE ( 'NONE', *, *, #10209, .T. ) ; +#8844 = SURFACE_SIDE_STYLE ('',( #78879 ) ) ; +#8845 = VERTEX_POINT ( 'NONE', #26511 ) ; +#8846 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8847 = LINE ( 'NONE', #40089, #7945 ) ; +#8848 = CARTESIAN_POINT ( 'NONE', ( 0.1595320655217619954, -1.429044931969539967, 0.8100000000000000533 ) ) ; +#8849 = VECTOR ( 'NONE', #22441, 1000.000000000000000 ) ; +#8850 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#8851 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#8852 = FACE_OUTER_BOUND ( 'NONE', #43804, .T. ) ; +#8853 = ORIENTED_EDGE ( 'NONE', *, *, #98106, .F. ) ; +#8854 = EDGE_CURVE ( 'NONE', #8011, #60846, #27997, .T. ) ; +#8855 = AXIS2_PLACEMENT_3D ( 'NONE', #81348, #87461, #10767 ) ; +#8856 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#8857 = EDGE_LOOP ( 'NONE', ( #63797, #4062, #91033, #85843, #81265, #70610 ) ) ; +#8858 = SURFACE_STYLE_USAGE ( .BOTH. , #46201 ) ; +#8860 = ADVANCED_FACE ( 'NONE', ( #50014 ), #89292, .T. ) ; +#8859 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79276, #17459, #9238, #40488 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#8861 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8862 = PLANE ( 'NONE', #73370 ) ; +#8863 = LINE ( 'NONE', #9871, #75123 ) ; +#8864 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90430 ) ) ; +#8865 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.899999999999996136, 2.990963115645192065E-79 ) ) ; +#8866 = ORIENTED_EDGE ( 'NONE', *, *, #62069, .F. ) ; +#8867 = PRESENTATION_STYLE_ASSIGNMENT (( #25319 ) ) ; +#8868 = PRESENTATION_STYLE_ASSIGNMENT (( #25813 ) ) ; +#8869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12713, 'distance_accuracy_value', 'NONE'); +#8870 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#8871 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54615 ) ) ; +#8872 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#8873 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8874 = ORIENTED_EDGE ( 'NONE', *, *, #56436, .F. ) ; +#8875 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7276 ), #54689 ) ; +#8876 = SURFACE_SIDE_STYLE ('',( #53925 ) ) ; +#8877 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8878 = ORIENTED_EDGE ( 'NONE', *, *, #21381, .T. ) ; +#8879 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#8880 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#8881 = SURFACE_STYLE_FILL_AREA ( #24327 ) ; +#8882 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93680 ) ) ; +#8883 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #79167, #32203 ), + ( #46999, #24052 ), + ( #530, #63370 ), + ( #54695, #100491 ), + ( #45955, #30652 ), + ( #15318, #62861 ), + ( #70475, #61846 ), + ( #69453, #9132 ), + ( #16836, #46476 ), + ( #78162, #92918 ), + ( #94457, #23037 ), + ( #77649, #8108 ), + ( #62350, #7604 ), + ( #38851, #40374 ), + ( #39332, #69972 ), + ( #1048, #47505 ), + ( #39854, #23 ), + ( #93924, #55208 ), + ( #31186, #71504 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06525924122584060572, 0.1303097080177630096, 0.1949669058053019877, 0.2594204141250909812, 0.3228188495375590161, 0.3840951885662929888, 0.4433054993635430208, 0.5020719067220029697, 0.5599285383667119698, 0.6178537031467949969, 0.6762349939776259866, 0.7358459849262459773, 0.7974378458162050265, 0.8614696408465449817, 0.9284772069666370475, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#8884 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #36550, #96437 ) ; +#8885 = EDGE_CURVE ( 'NONE', #15336, #48171, #45787, .T. ) ; +#8886 = AXIS2_PLACEMENT_3D ( 'NONE', #92211, #37118, #28929 ) ; +#8887 = EDGE_CURVE ( 'NONE', #35608, #42994, #67782, .T. ) ; +#8888 = ORIENTED_EDGE ( 'NONE', *, *, #98190, .T. ) ; +#8890 = EDGE_LOOP ( 'NONE', ( #9798, #74558, #47099, #14375 ) ) ; +#8889 = SURFACE_STYLE_FILL_AREA ( #78924 ) ; +#8892 = VECTOR ( 'NONE', #11853, 999.9999999999998863 ) ; +#8891 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41321, 'distance_accuracy_value', 'NONE'); +#8893 = SURFACE_SIDE_STYLE ('',( #24844 ) ) ; +#8895 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8894 = PRESENTATION_STYLE_ASSIGNMENT (( #10388 ) ) ; +#8896 = SURFACE_STYLE_FILL_AREA ( #21782 ) ; +#8897 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82328 ) ) ; +#8898 = ORIENTED_EDGE ( 'NONE', *, *, #58863, .F. ) ; +#8899 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 2.299999999999999822, -0.02000000000000419845 ) ) ; +#8900 = VECTOR ( 'NONE', #71302, 1000.000000000000000 ) ; +#8901 = SURFACE_STYLE_FILL_AREA ( #48330 ) ; +#8902 = AXIS2_PLACEMENT_3D ( 'NONE', #30884, #62066, #70184 ) ; +#8903 = ORIENTED_EDGE ( 'NONE', *, *, #82125, .T. ) ; +#8905 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#8904 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#8906 = ORIENTED_EDGE ( 'NONE', *, *, #81482, .F. ) ; +#8907 = VERTEX_POINT ( 'NONE', #7441 ) ; +#8908 = VECTOR ( 'NONE', #25266, 1000.000000000000000 ) ; +#8910 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8909 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#8911 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#8912 = FACE_OUTER_BOUND ( 'NONE', #61493, .T. ) ; +#8913 = ORIENTED_EDGE ( 'NONE', *, *, #41374, .T. ) ; +#8914 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#8915 = PRESENTATION_STYLE_ASSIGNMENT (( #24869 ) ) ; +#8916 = FILL_AREA_STYLE_COLOUR ( '', #78076 ) ; +#8917 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28540 ) ) ; +#8918 = FILL_AREA_STYLE_COLOUR ( '', #81641 ) ; +#8919 = ORIENTED_EDGE ( 'NONE', *, *, #69607, .F. ) ; +#8920 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#8921 = ORIENTED_EDGE ( 'NONE', *, *, #18600, .T. ) ; +#8923 = ORIENTED_EDGE ( 'NONE', *, *, #93671, .F. ) ; +#8922 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #21565, #52243, #28240, #11807 ), + ( #28719, #95758, #68006, #44044 ), + ( #29236, #74705, #43043, #75209 ), + ( #27757, #50744, #36405, #67507 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606871933, 0.6476030138606871933, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606871933, 0.6476030138606871933, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#8924 = FILL_AREA_STYLE ('',( #7413 ) ) ; +#8926 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8925 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8927 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, -3.099999999999992095, 0.000000000000000000 ) ) ; +#8928 = EDGE_CURVE ( 'NONE', #34634, #90693, #45288, .T. ) ; +#8929 = AXIS2_PLACEMENT_3D ( 'NONE', #65998, #25694, #27214 ) ; +#8930 = LINE ( 'NONE', #93733, #20527 ) ; +#8931 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701300244, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#8932 = EDGE_CURVE ( 'NONE', #38401, #62858, #61179, .T. ) ; +#8933 = CARTESIAN_POINT ( 'NONE', ( -0.1139798271265630020, -1.164588072778879990, 0.8100000000000000533 ) ) ; +#8934 = SURFACE_SIDE_STYLE ('',( #78967 ) ) ; +#8935 = SURFACE_SIDE_STYLE ('',( #48369 ) ) ; +#8936 = ORIENTED_EDGE ( 'NONE', *, *, #46633, .T. ) ; +#8938 = AXIS2_PLACEMENT_3D ( 'NONE', #84139, #37196, #68298 ) ; +#8937 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8939 = EDGE_CURVE ( 'NONE', #4914, #83615, #29982, .T. ) ; +#8940 = PLANE ( 'NONE', #39200 ) ; +#8941 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8942 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8943 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93050 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91558, #98634, #76232 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8944 = STYLED_ITEM ( 'NONE', ( #66779 ), #54111 ) ; +#8945 = PRESENTATION_STYLE_ASSIGNMENT (( #62677 ) ) ; +#8946 = ADVANCED_FACE ( 'NONE', ( #69792 ), #62188, .T. ) ; +#8947 = CARTESIAN_POINT ( 'NONE', ( 1.980039375677109970, 1.416514402982369969, -11.41719400909158111 ) ) ; +#8948 = FACE_OUTER_BOUND ( 'NONE', #13815, .T. ) ; +#8949 = VERTEX_POINT ( 'NONE', #5958 ) ; +#8950 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.000000000000000000 ) ) ; +#8951 = SURFACE_STYLE_USAGE ( .BOTH. , #48386 ) ; +#8952 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.1600000000000000033, 1.250000000000000000 ) ) ; +#8953 = PLANE ( 'NONE', #84316 ) ; +#8954 = CIRCLE ( 'NONE', #17189, 0.5300000000829642177 ) ; +#8955 = VECTOR ( 'NONE', #28916, 1000.000000000000000 ) ; +#8956 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52868 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64836, #95948, #65328 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8957 = SURFACE_STYLE_USAGE ( .BOTH. , #16661 ) ; +#8958 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8959 = EDGE_CURVE ( 'NONE', #91124, #88958, #60665, .T. ) ; +#8961 = ADVANCED_FACE ( 'NONE', ( #94274 ), #17181, .T. ) ; +#8960 = LINE ( 'NONE', #46301, #35081 ) ; +#8962 = DIRECTION ( 'NONE', ( 0.9388213331153589802, 0.000000000000000000, -0.3444045651374270656 ) ) ; +#8963 = SURFACE_SIDE_STYLE ('',( #24913 ) ) ; +#8964 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#8965 = FACE_OUTER_BOUND ( 'NONE', #16959, .T. ) ; +#8966 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#8967 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8648700000000000276 ) ) ; +#8968 = EDGE_CURVE ( 'NONE', #48771, #93560, #24899, .T. ) ; +#8969 = EDGE_CURVE ( 'NONE', #97446, #61132, #868, .T. ) ; +#8970 = CARTESIAN_POINT ( 'NONE', ( 1.890937141840999702, -1.269147371132230084, 0.8100000000000004974 ) ) ; +#8971 = PLANE ( 'NONE', #52015 ) ; +#8972 = STYLED_ITEM ( 'NONE', ( #4303 ), #22558 ) ; +#8973 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#8974 = LINE ( 'NONE', #94800, #51961 ) ; +#8975 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, -0.01500000000000001332, -0.2458578643762690530 ) ) ; +#8976 = ORIENTED_EDGE ( 'NONE', *, *, #29097, .T. ) ; +#8977 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#8978 = SURFACE_SIDE_STYLE ('',( #64205 ) ) ; +#8979 = LINE ( 'NONE', #80047, #94196 ) ; +#8980 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#8981 = ADVANCED_FACE ( 'NONE', ( #95781 ), #40201, .T. ) ; +#8982 = AXIS2_PLACEMENT_3D ( 'NONE', #58947, #51765, #67540 ) ; +#8984 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#8983 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#8986 = STYLED_ITEM ( 'NONE', ( #73068 ), #4645 ) ; +#8987 = EDGE_CURVE ( 'NONE', #5652, #58941, #33028, .T. ) ; +#8988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11825, #4263, #76584 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#8989 = FACE_OUTER_BOUND ( 'NONE', #69579, .T. ) ; +#8990 = ORIENTED_EDGE ( 'NONE', *, *, #3063, .F. ) ; +#8991 = FACE_OUTER_BOUND ( 'NONE', #79437, .T. ) ; +#8992 = STYLED_ITEM ( 'NONE', ( #52701 ), #3768 ) ; +#8993 = FILL_AREA_STYLE ('',( #18210 ) ) ; +#8994 = LINE ( 'NONE', #86166, #3828 ) ; +#8995 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#8996 = VECTOR ( 'NONE', #25681, 1000.000000000000000 ) ; +#8997 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#8998 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#8999 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9000 = ORIENTED_EDGE ( 'NONE', *, *, #57633, .F. ) ; +#9001 = ORIENTED_EDGE ( 'NONE', *, *, #93828, .T. ) ; +#9002 = ORIENTED_EDGE ( 'NONE', *, *, #67700, .T. ) ; +#9003 = AXIS2_PLACEMENT_3D ( 'NONE', #34167, #12071, #96386 ) ; +#9004 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9005 = FILL_AREA_STYLE_COLOUR ( '', #93972 ) ; +#9006 = SURFACE_SIDE_STYLE ('',( #39733 ) ) ; +#9007 = CARTESIAN_POINT ( 'NONE', ( -1.343981097684900039, -0.9654894655288509542, 0.8299999999999997380 ) ) ; +#9008 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9009 = VECTOR ( 'NONE', #34289, 1000.000000000000114 ) ; +#9011 = ORIENTED_EDGE ( 'NONE', *, *, #49538, .T. ) ; +#9010 = ORIENTED_EDGE ( 'NONE', *, *, #32971, .T. ) ; +#9012 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#9013 = ADVANCED_FACE ( 'NONE', ( #353 ), #31514, .F. ) ; +#9014 = ORIENTED_EDGE ( 'NONE', *, *, #58383, .T. ) ; +#9015 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9016 = VECTOR ( 'NONE', #84473, 1000.000000000000000 ) ; +#9017 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27536, 'distance_accuracy_value', 'NONE'); +#9018 = CARTESIAN_POINT ( 'NONE', ( 0.4915531961084259605, -0.9443244458491719673, 0.8100000000000010525 ) ) ; +#9019 = ORIENTED_EDGE ( 'NONE', *, *, #53900, .T. ) ; +#9020 = EDGE_CURVE ( 'NONE', #52415, #28324, #3887, .T. ) ; +#9021 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9022 = VECTOR ( 'NONE', #39827, 1000.000000000000000 ) ; +#9023 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#9024 = ORIENTED_EDGE ( 'NONE', *, *, #92507, .T. ) ; +#9026 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9025 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#9027 = VERTEX_POINT ( 'NONE', #88654 ) ; +#9028 = AXIS2_PLACEMENT_3D ( 'NONE', #78071, #7020, #63282 ) ; +#9029 = STYLED_ITEM ( 'NONE', ( #43603 ), #48725 ) ; +#9031 = SURFACE_SIDE_STYLE ('',( #56104 ) ) ; +#9030 = PLANE ( 'NONE', #99151 ) ; +#9032 = EDGE_LOOP ( 'NONE', ( #34337, #73041, #70232, #62357 ) ) ; +#9033 = ORIENTED_EDGE ( 'NONE', *, *, #26245, .T. ) ; +#9034 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#9035 = VECTOR ( 'NONE', #54595, 1000.000000000000000 ) ; +#9036 = CYLINDRICAL_SURFACE ( 'NONE', #6875, 0.6500000000000001332 ) ; +#9037 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544766999999999779, 0.8991599999999999593 ) ) ; +#9038 = EDGE_CURVE ( 'NONE', #87120, #42980, #81544, .T. ) ; +#9040 = VERTEX_POINT ( 'NONE', #72847 ) ; +#9039 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146561253, 0.2541340759269650196, 0.8100000000000000533 ) ) ; +#9041 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.7099999999999999645, -0.7999999999999999334 ) ) ; +#9042 = SURFACE_SIDE_STYLE ('',( #9546 ) ) ; +#9043 = AXIS2_PLACEMENT_3D ( 'NONE', #85274, #45939, #70981 ) ; +#9044 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15245, #84239, #29116, #85226 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9045 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8648700000000000276 ) ) ; +#9046 = VERTEX_POINT ( 'NONE', #82520 ) ; +#9048 = PLANE ( 'NONE', #79559 ) ; +#9047 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.000000000000000000 ) ) ; +#9049 = ORIENTED_EDGE ( 'NONE', *, *, #62160, .F. ) ; +#9050 = ORIENTED_EDGE ( 'NONE', *, *, #29124, .T. ) ; +#9052 = FACE_OUTER_BOUND ( 'NONE', #33186, .T. ) ; +#9051 = FACE_OUTER_BOUND ( 'NONE', #61277, .T. ) ; +#9053 = ADVANCED_FACE ( 'NONE', ( #81030 ), #82022, .T. ) ; +#9054 = LINE ( 'NONE', #71940, #92160 ) ; +#9055 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#9056 = VECTOR ( 'NONE', #48634, 1000.000000000000000 ) ; +#9057 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#9058 = VECTOR ( 'NONE', #35723, 1000.000000000000000 ) ; +#9059 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9060 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#9061 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53516, 'distance_accuracy_value', 'NONE'); +#9062 = AXIS2_PLACEMENT_3D ( 'NONE', #44369, #76533, #68849 ) ; +#9063 = SURFACE_STYLE_FILL_AREA ( #80128 ) ; +#9064 = EDGE_LOOP ( 'NONE', ( #25669, #34370, #53796, #6758 ) ) ; +#9065 = LINE ( 'NONE', #72425, #73539 ) ; +#9066 = SURFACE_STYLE_FILL_AREA ( #84729 ) ; +#9067 = ORIENTED_EDGE ( 'NONE', *, *, #32550, .T. ) ; +#9068 = STYLED_ITEM ( 'NONE', ( #65252 ), #3823 ) ; +#9069 = SURFACE_STYLE_FILL_AREA ( #8042 ) ; +#9070 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#9071 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9072 = PRESENTATION_STYLE_ASSIGNMENT (( #70941 ) ) ; +#9074 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#9073 = FILL_AREA_STYLE ('',( #93859 ) ) ; +#9075 = LINE ( 'NONE', #87773, #4721 ) ; +#9076 = SURFACE_STYLE_FILL_AREA ( #56666 ) ; +#9077 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.000000000000000000 ) ) ; +#9078 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #43625, #81970, #27335, #49828 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9079 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9080 = PRESENTATION_STYLE_ASSIGNMENT (( #16280 ) ) ; +#9081 = DIRECTION ( 'NONE', ( -0.7071067811865435759, -0.7071067811865514585, 0.000000000000000000 ) ) ; +#9082 = SURFACE_STYLE_USAGE ( .BOTH. , #9580 ) ; +#9083 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9084 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12289 ), #90650 ) ; +#9085 = SURFACE_STYLE_USAGE ( .BOTH. , #46945 ) ; +#9086 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9087 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85749 ) ) ; +#9088 = CARTESIAN_POINT ( 'NONE', ( 3.843461124874956614, 7.105605124874957212, 0.8991599999999999593 ) ) ; +#9089 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9090 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#9091 = ADVANCED_FACE ( 'NONE', ( #66670 ), #49358, .T. ) ; +#9092 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61393 ) ) ; +#9093 = VECTOR ( 'NONE', #13745, 1000.000000000000000 ) ; +#9094 = ORIENTED_EDGE ( 'NONE', *, *, #25361, .F. ) ; +#9095 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.000000000000000000 ) ) ; +#9096 = FILL_AREA_STYLE ('',( #55174 ) ) ; +#9097 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21455, 'distance_accuracy_value', 'NONE'); +#9098 = ORIENTED_EDGE ( 'NONE', *, *, #3288, .F. ) ; +#9100 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62828, 'distance_accuracy_value', 'NONE'); +#9099 = SURFACE_STYLE_USAGE ( .BOTH. , #16800 ) ; +#9101 = FILL_AREA_STYLE ('',( #47988 ) ) ; +#9102 = SURFACE_STYLE_FILL_AREA ( #25534 ) ; +#9103 = PRESENTATION_STYLE_ASSIGNMENT (( #79141 ) ) ; +#9104 = EDGE_CURVE ( 'NONE', #73476, #54246, #84013, .T. ) ; +#9105 = FILL_AREA_STYLE_COLOUR ( '', #49912 ) ; +#9107 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9106 = STYLED_ITEM ( 'NONE', ( #12943 ), #78771 ) ; +#9108 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9109 = PRODUCT ( 'R0201_20210301.xtd', 'R0201_20210301.xtd', '', ( #24451 ) ) ; +#9110 = EDGE_CURVE ( 'NONE', #57698, #90959, #53371, .T. ) ; +#9111 = AXIS2_PLACEMENT_3D ( 'NONE', #36638, #66740, #26962 ) ; +#9112 = ORIENTED_EDGE ( 'NONE', *, *, #86531, .F. ) ; +#9113 = LINE ( 'NONE', #95432, #36097 ) ; +#9114 = ORIENTED_EDGE ( 'NONE', *, *, #70860, .F. ) ; +#9115 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9117 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65454, 'distance_accuracy_value', 'NONE'); +#9118 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9119 = PLANE ( 'NONE', #77605 ) ; +#9120 = FILL_AREA_STYLE ('',( #87814 ) ) ; +#9121 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9122 = LINE ( 'NONE', #32193, #22383 ) ; +#9123 = ORIENTED_EDGE ( 'NONE', *, *, #34242, .T. ) ; +#9124 = CARTESIAN_POINT ( 'NONE', ( 1.111216736053209919, -0.9708075278790050389, 0.8300000000000002931 ) ) ; +#9125 = FILL_AREA_STYLE_COLOUR ( '', #10174 ) ; +#9126 = EDGE_LOOP ( 'NONE', ( #99335, #2281, #150, #28073 ) ) ; +#9127 = AXIS2_PLACEMENT_3D ( 'NONE', #50908, #94922, #3910 ) ; +#9128 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#9129 = ORIENTED_EDGE ( 'NONE', *, *, #14768, .F. ) ; +#9130 = PRESENTATION_STYLE_ASSIGNMENT (( #16833 ) ) ; +#9131 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67827 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58096, #26420, #49916 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9132 = CARTESIAN_POINT ( 'NONE', ( 1.115802419441249915, -1.426518300252259897, 0.8299999999999999600 ) ) ; +#9133 = SURFACE_STYLE_USAGE ( .BOTH. , #10624 ) ; +#9134 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#9135 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9136 = LINE ( 'NONE', #65344, #93130 ) ; +#9137 = FILL_AREA_STYLE ('',( #2077 ) ) ; +#9138 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#9140 = ORIENTED_EDGE ( 'NONE', *, *, #43082, .T. ) ; +#9139 = ORIENTED_EDGE ( 'NONE', *, *, #36648, .T. ) ; +#9141 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97235 ) ) ; +#9142 = LINE ( 'NONE', #24590, #51928 ) ; +#9143 = PRESENTATION_STYLE_ASSIGNMENT (( #71519 ) ) ; +#9144 = ORIENTED_EDGE ( 'NONE', *, *, #4271, .F. ) ; +#9145 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9146 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#9147 = EDGE_LOOP ( 'NONE', ( #21538, #68158, #95778, #41800 ) ) ; +#9148 = EDGE_CURVE ( 'NONE', #71612, #27601, #5848, .T. ) ; +#9149 = ORIENTED_EDGE ( 'NONE', *, *, #43403, .F. ) ; +#9150 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9151 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#9152 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9154 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9153 = CARTESIAN_POINT ( 'NONE', ( 0.03333333333332499926, 3.500000000000000000, 0.000000000000000000 ) ) ; +#9155 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#9156 = ORIENTED_EDGE ( 'NONE', *, *, #22773, .F. ) ; +#9158 = EDGE_LOOP ( 'NONE', ( #76446, #38382, #58262, #94916 ) ) ; +#9157 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53260 ) ) ; +#9159 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#9160 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6976, #40245, #69308, #31561 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9161 = ORIENTED_EDGE ( 'NONE', *, *, #88921, .F. ) ; +#9162 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8099999999999416556 ) ) ; +#9163 = AXIS2_PLACEMENT_3D ( 'NONE', #13328, #14869, #77711 ) ; +#9165 = EDGE_LOOP ( 'NONE', ( #51996, #65003, #20839, #6003, #96876, #30623, #74184, #100476 ) ) ; +#9164 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.966666666666666785, 0.000000000000000000 ) ) ; +#9166 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9238200612200859752, 0.000000000000000000 ) ) ; +#9167 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7546 ) ) ; +#9168 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23999 ), #58197 ) ; +#9169 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9170 = ORIENTED_EDGE ( 'NONE', *, *, #4853, .T. ) ; +#9171 = SURFACE_STYLE_USAGE ( .BOTH. , #16878 ) ; +#9172 = LINE ( 'NONE', #88878, #41195 ) ; +#9173 = VERTEX_POINT ( 'NONE', #6335 ) ; +#9174 = CARTESIAN_POINT ( 'NONE', ( -1.325735931288071656, 0.6892893218813453959, -1.100000000000000089 ) ) ; +#9175 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40243 ), #35319 ) ; +#9176 = PRESENTATION_STYLE_ASSIGNMENT (( #8650 ) ) ; +#9177 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9178 = ADVANCED_FACE ( 'NONE', ( #14514 ), #83518, .T. ) ; +#9179 = LINE ( 'NONE', #9681, #33062 ) ; +#9180 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9182 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#9181 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9183 = LINE ( 'NONE', #49600, #50741 ) ; +#9184 = PRESENTATION_STYLE_ASSIGNMENT (( #40939 ) ) ; +#9185 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20701 ) ) ; +#9186 = ORIENTED_EDGE ( 'NONE', *, *, #53331, .T. ) ; +#9187 = FILL_AREA_STYLE ('',( #94514 ) ) ; +#9188 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9189 = CARTESIAN_POINT ( 'NONE', ( -0.03881103786207359962, 1.364228230794140018, 0.8100000000000000533 ) ) ; +#9190 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18468 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11596, #75478, #28513 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9191 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19879 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40616, #63611, #15569 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9192 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#9193 = CARTESIAN_POINT ( 'NONE', ( 0.3999999999999998002, 0.6700000000000000400, 0.1999999999999999833 ) ) ; +#9195 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#9194 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9196 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9197 = EDGE_CURVE ( 'NONE', #64584, #15091, #91168, .T. ) ; +#9198 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#9199 = VECTOR ( 'NONE', #37957, 1000.000000000000000 ) ; +#9200 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9201 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9202 = ORIENTED_EDGE ( 'NONE', *, *, #45905, .F. ) ; +#9203 = VECTOR ( 'NONE', #41740, 1000.000000000000000 ) ; +#9204 = FILL_AREA_STYLE_COLOUR ( '', #41702 ) ; +#9205 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#9206 = ORIENTED_EDGE ( 'NONE', *, *, #4827, .T. ) ; +#9207 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#9209 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853450028, 0.2349715759269649928, 0.8100000000000000533 ) ) ; +#9208 = SURFACE_STYLE_FILL_AREA ( #96035 ) ; +#9210 = FILL_AREA_STYLE ('',( #56292 ) ) ; +#9212 = EDGE_CURVE ( 'NONE', #15383, #46032, #59578, .T. ) ; +#9211 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59847 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11770, #27219, #10773 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9213 = EDGE_LOOP ( 'NONE', ( #86418, #17947, #18895, #70645 ) ) ; +#9214 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#9215 = PRESENTATION_STYLE_ASSIGNMENT (( #1655 ) ) ; +#9216 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#9217 = SURFACE_STYLE_USAGE ( .BOTH. , #87411 ) ; +#9218 = LINE ( 'NONE', #116, #80814 ) ; +#9219 = VECTOR ( 'NONE', #86636, 1000.000000000000000 ) ; +#9220 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9221 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#9222 = PRESENTATION_STYLE_ASSIGNMENT (( #10206 ) ) ; +#9223 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15873, 'distance_accuracy_value', 'NONE'); +#9224 = EDGE_CURVE ( 'NONE', #68224, #92405, #45663, .T. ) ; +#9225 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9226 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21473 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30106, #92387, #14755 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9227 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, -0.2999999999999999889, -0.02000000000002940051 ) ) ; +#9228 = VERTEX_POINT ( 'NONE', #92149 ) ; +#9229 = FILL_AREA_STYLE ('',( #41476 ) ) ; +#9230 = EDGE_LOOP ( 'NONE', ( #4418, #65006, #34042, #56004 ) ) ; +#9231 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23111, 'distance_accuracy_value', 'NONE'); +#9232 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8644, 'distance_accuracy_value', 'NONE'); +#9233 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#9234 = SURFACE_STYLE_USAGE ( .BOTH. , #39963 ) ; +#9235 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, 0.09999999999999988065, 0.000000000000000000 ) ) ; +#9236 = VECTOR ( 'NONE', #58206, 1000.000000000000000 ) ; +#9237 = CARTESIAN_POINT ( 'NONE', ( -0.09183755801571232003, -1.507352529807550079, 0.8300000000000004041 ) ) ; +#9238 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2761799387799150352, -0.02000000000000000042 ) ) ; +#9239 = ORIENTED_EDGE ( 'NONE', *, *, #10931, .T. ) ; +#9240 = CARTESIAN_POINT ( 'NONE', ( 1.876343683457829981, -1.423344911062679907, 0.8300000000000011813 ) ) ; +#9242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9241 = AXIS2_PLACEMENT_3D ( 'NONE', #68171, #12985, #59586 ) ; +#9243 = CARTESIAN_POINT ( 'NONE', ( 0.9002637987012980236, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#9244 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96136, 'distance_accuracy_value', 'NONE'); +#9245 = SURFACE_STYLE_FILL_AREA ( #26685 ) ; +#9246 = ORIENTED_EDGE ( 'NONE', *, *, #64665, .F. ) ; +#9247 = VECTOR ( 'NONE', #25135, 1000.000000000000000 ) ; +#9248 = VERTEX_POINT ( 'NONE', #84997 ) ; +#9249 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8648700000000000276 ) ) ; +#9250 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#9251 = EDGE_CURVE ( 'NONE', #39573, #21633, #92633, .T. ) ; +#9252 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220025313, -2.499999999999999556, -0.02000000000000000042 ) ) ; +#9254 = FILL_AREA_STYLE ('',( #48153 ) ) ; +#9253 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68049 ) ) ; +#9255 = CARTESIAN_POINT ( 'NONE', ( 4.798055124874956334, 3.548857875125043915, 0.8648700000000000276 ) ) ; +#9256 = ORIENTED_EDGE ( 'NONE', *, *, #43419, .T. ) ; +#9257 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9258 = SURFACE_STYLE_USAGE ( .BOTH. , #85935 ) ; +#9259 = EDGE_LOOP ( 'NONE', ( #41456, #55079, #72763, #21680 ) ) ; +#9260 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39208 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95572, #11747, #26691 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9261 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#9262 = PRESENTATION_STYLE_ASSIGNMENT (( #24191 ) ) ; +#9263 = CLOSED_SHELL ( 'NONE', ( #65502, #82214, #19794, #89244, #23893, #98086 ) ) ; +#9264 = EDGE_CURVE ( 'NONE', #66829, #2623, #28874, .T. ) ; +#9265 = ORIENTED_EDGE ( 'NONE', *, *, #80182, .T. ) ; +#9266 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14655 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40996, #66460, #65446 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9267 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9268 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 4.266452400824600274E-34 ) ) ; +#9269 = CARTESIAN_POINT ( 'NONE', ( 1.799895807589950048, -1.058723197808659977, 0.8300000000000004041 ) ) ; +#9270 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#9271 = PLANE ( 'NONE', #35587 ) ; +#9272 = SURFACE_STYLE_FILL_AREA ( #55834 ) ; +#9273 = EDGE_LOOP ( 'NONE', ( #59998, #68275, #34388, #75314, #44970, #94552 ) ) ; +#9275 = ORIENTED_EDGE ( 'NONE', *, *, #43385, .F. ) ; +#9274 = EDGE_LOOP ( 'NONE', ( #56392, #93241, #58786, #55136 ) ) ; +#9276 = STYLED_ITEM ( 'NONE', ( #6619 ), #5647 ) ; +#9277 = ORIENTED_EDGE ( 'NONE', *, *, #63748, .T. ) ; +#9278 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19113 ) ) ; +#9279 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#9280 = ORIENTED_EDGE ( 'NONE', *, *, #95082, .T. ) ; +#9281 = VERTEX_POINT ( 'NONE', #7318 ) ; +#9282 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#9284 = FACE_OUTER_BOUND ( 'NONE', #55844, .T. ) ; +#9283 = SURFACE_SIDE_STYLE ('',( #96115 ) ) ; +#9285 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9286 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9287 = VERTEX_POINT ( 'NONE', #60062 ) ; +#9288 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#9289 = CARTESIAN_POINT ( 'NONE', ( 1.807266337641940224, -1.389839611604140046, 0.8099999999999997202 ) ) ; +#9290 = EDGE_LOOP ( 'NONE', ( #24898, #23437, #10165, #41742 ) ) ; +#9291 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9292 = DIRECTION ( 'NONE', ( 0.9961493162234444920, -0.08767291364819451704, 0.000000000000000000 ) ) ; +#9293 = SURFACE_SIDE_STYLE ('',( #49206 ) ) ; +#9294 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24049 ) ) ; +#9295 = ORIENTED_EDGE ( 'NONE', *, *, #13738, .T. ) ; +#9296 = STYLED_ITEM ( 'NONE', ( #13999 ), #74333 ) ; +#9297 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9298 = ORIENTED_EDGE ( 'NONE', *, *, #30395, .T. ) ; +#9299 = EDGE_CURVE ( 'NONE', #14054, #31896, #69135, .T. ) ; +#9300 = DIRECTION ( 'NONE', ( 0.7071090539100487460, 0.7071045084557415761, 0.000000000000000000 ) ) ; +#9301 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.35000000000000142 ) ) ; +#9302 = VECTOR ( 'NONE', #85628, 1000.000000000000000 ) ; +#9303 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9304 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#9305 = SURFACE_STYLE_USAGE ( .BOTH. , #32882 ) ; +#9306 = VECTOR ( 'NONE', #34590, 1000.000000000000000 ) ; +#9307 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15917 ) ) ; +#9308 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#9309 = ORIENTED_EDGE ( 'NONE', *, *, #51123, .T. ) ; +#9311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9310 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9312 = EDGE_CURVE ( 'NONE', #66049, #57759, #40093, .T. ) ; +#9313 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82727 ) ) ; +#9314 = FILL_AREA_STYLE ('',( #77823 ) ) ; +#9315 = EDGE_CURVE ( 'NONE', #7382, #31354, #20713, .T. ) ; +#9316 = CARTESIAN_POINT ( 'NONE', ( -1.000023319491960105, -0.9315058289328710384, 0.8299999999999999600 ) ) ; +#9317 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#9318 = DIRECTION ( 'NONE', ( 0.7071045084557415761, -0.7071090539100487460, 0.000000000000000000 ) ) ; +#9319 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#9320 = LINE ( 'NONE', #8302, #91815 ) ; +#9321 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, 0.000000000000000000 ) ) ; +#9322 = PRESENTATION_STYLE_ASSIGNMENT (( #23229 ) ) ; +#9323 = ORIENTED_EDGE ( 'NONE', *, *, #46139, .F. ) ; +#9324 = LINE ( 'NONE', #30336, #15512 ) ; +#9325 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#9326 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42069 ) ) ; +#9328 = LINE ( 'NONE', #2272, #34432 ) ; +#9327 = PRESENTATION_STYLE_ASSIGNMENT (( #40055 ) ) ; +#9329 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9330 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9331 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9332 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55065 ) ) ; +#9333 = EDGE_CURVE ( 'NONE', #87763, #97102, #91787, .T. ) ; +#9334 = PRESENTATION_STYLE_ASSIGNMENT (( #96666 ) ) ; +#9335 = CLOSED_SHELL ( 'NONE', ( #48364, #86512, #60518, #92644, #40020, #95989, #26600, #73412, #66590, #25910, #97169, #52565, #91268, #88685, #28962, #32978, #86888, #93265, #100345, #71463, #34896, #10205, #29514, #68647, #69212, #92751, #8366, #84532, #93586, #7649, #81480, #13163, #85646, #14022, #71465, #94893, #43985, #97861, #62632, #91904, #50373, #94894, #69767, #78907 ) ) ; +#9336 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#9337 = ORIENTED_EDGE ( 'NONE', *, *, #65206, .T. ) ; +#9338 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#9339 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#9341 = EDGE_CURVE ( 'NONE', #27567, #66963, #32411, .T. ) ; +#9340 = FACE_OUTER_BOUND ( 'NONE', #40843, .T. ) ; +#9342 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9343 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9344 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9345 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9346 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9347 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9348 = AXIS2_PLACEMENT_3D ( 'NONE', #68007, #20560, #34914 ) ; +#9349 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#9350 = FILL_AREA_STYLE ('',( #80400 ) ) ; +#9351 = FACE_OUTER_BOUND ( 'NONE', #29852, .T. ) ; +#9352 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#9353 = CYLINDRICAL_SURFACE ( 'NONE', #92536, 0.2137111836784290342 ) ; +#9354 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9355 = ADVANCED_FACE ( 'NONE', ( #87530 ), #31898, .T. ) ; +#9356 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#9357 = VERTEX_POINT ( 'NONE', #8824 ) ; +#9358 = FILL_AREA_STYLE ('',( #95676 ) ) ; +#9359 = VERTEX_POINT ( 'NONE', #47212 ) ; +#9360 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11266, 'distance_accuracy_value', 'NONE'); +#9361 = SURFACE_STYLE_USAGE ( .BOTH. , #79399 ) ; +#9362 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000777, 0.1499999999999999944 ) ) ; +#9363 = CARTESIAN_POINT ( 'NONE', ( 0.2846257902759590230, -1.272935805450750246, 0.8299999999999999600 ) ) ; +#9364 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9365 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#9366 = CARTESIAN_POINT ( 'NONE', ( -0.9854791524880751608, -1.205184960463220323, 0.8100000000000000533 ) ) ; +#9367 = EDGE_LOOP ( 'NONE', ( #58875, #36259, #36657, #40526 ) ) ; +#9368 = SURFACE_STYLE_USAGE ( .BOTH. , #33460 ) ; +#9369 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22700, 'distance_accuracy_value', 'NONE'); +#9370 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#9371 = AXIS2_PLACEMENT_3D ( 'NONE', #95965, #40378, #10626 ) ; +#9372 = FILL_AREA_STYLE_COLOUR ( '', #34077 ) ; +#9373 = EDGE_LOOP ( 'NONE', ( #6002, #97061, #25231, #47798 ) ) ; +#9374 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#9375 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#9376 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#9377 = STYLED_ITEM ( 'NONE', ( #79369 ), #31200 ) ; +#9378 = EDGE_CURVE ( 'NONE', #57623, #67087, #76594, .T. ) ; +#9379 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#9380 = CARTESIAN_POINT ( 'NONE', ( -1.207523339372349902, -1.437310919031880241, 0.8100000000000000533 ) ) ; +#9381 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9382 = VERTEX_POINT ( 'NONE', #56429 ) ; +#9383 = FILL_AREA_STYLE_COLOUR ( '', #74209 ) ; +#9384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3833 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90090, #97229, #12407 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9385 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#9386 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27947, 'distance_accuracy_value', 'NONE'); +#9387 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9389 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9388 = AXIS2_PLACEMENT_3D ( 'NONE', #61935, #92034, #68040 ) ; +#9390 = LINE ( 'NONE', #78406, #14835 ) ; +#9391 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#9392 = EDGE_CURVE ( 'NONE', #13814, #29448, #48752, .T. ) ; +#9393 = VERTEX_POINT ( 'NONE', #71199 ) ; +#9394 = LINE ( 'NONE', #84678, #90423 ) ; +#9395 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9396 = SURFACE_SIDE_STYLE ('',( #18624 ) ) ; +#9397 = ORIENTED_EDGE ( 'NONE', *, *, #18111, .F. ) ; +#9398 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#9399 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000971, 0.1499999999999999944 ) ) ; +#9400 = EDGE_CURVE ( 'NONE', #23282, #91128, #31388, .T. ) ; +#9401 = SURFACE_STYLE_FILL_AREA ( #10380 ) ; +#9402 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9403 = VECTOR ( 'NONE', #52391, 1000.000000000000000 ) ; +#9404 = ADVANCED_FACE ( 'NONE', ( #9340 ), #46690, .T. ) ; +#9405 = ORIENTED_EDGE ( 'NONE', *, *, #73328, .F. ) ; +#9406 = ORIENTED_EDGE ( 'NONE', *, *, #15353, .T. ) ; +#9407 = STYLED_ITEM ( 'NONE', ( #47611 ), #41430 ) ; +#9408 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#9409 = VECTOR ( 'NONE', #68208, 1000.000000000000000 ) ; +#9410 = LINE ( 'NONE', #8385, #52960 ) ; +#9411 = CLOSED_SHELL ( 'NONE', ( #94280, #31951, #58004, #7245, #69401, #1568 ) ) ; +#9412 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#9413 = VERTEX_POINT ( 'NONE', #2775 ) ; +#9414 = LINE ( 'NONE', #41662, #22008 ) ; +#9415 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66647, #26373, #82991, #27891 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9416 = FACE_OUTER_BOUND ( 'NONE', #16007, .T. ) ; +#9417 = AXIS2_PLACEMENT_3D ( 'NONE', #49032, #48010, #8595 ) ; +#9418 = ORIENTED_EDGE ( 'NONE', *, *, #57880, .F. ) ; +#9419 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48129 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62798, #33147, #17300 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9420 = LINE ( 'NONE', #79464, #1517 ) ; +#9421 = ORIENTED_EDGE ( 'NONE', *, *, #29252, .T. ) ; +#9422 = ORIENTED_EDGE ( 'NONE', *, *, #3439, .F. ) ; +#9423 = EDGE_CURVE ( 'NONE', #93750, #22953, #49761, .T. ) ; +#9424 = LINE ( 'NONE', #42175, #16738 ) ; +#9425 = VECTOR ( 'NONE', #13116, 1000.000000000000000 ) ; +#9427 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9426 = CARTESIAN_POINT ( 'NONE', ( 0.3016031042252979022, -1.262460105004481248, 0.8099999999999999423 ) ) ; +#9428 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82912 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16135, #84601, #23339 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9429 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8991599999999999593 ) ) ; +#9430 = ORIENTED_EDGE ( 'NONE', *, *, #20769, .T. ) ; +#9431 = AXIS2_PLACEMENT_3D ( 'NONE', #631, #17451, #40987 ) ; +#9432 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#9433 = ORIENTED_EDGE ( 'NONE', *, *, #31958, .F. ) ; +#9434 = EDGE_LOOP ( 'NONE', ( #66083, #35520, #96938, #45466 ) ) ; +#9435 = EDGE_LOOP ( 'NONE', ( #51931, #508, #61676, #71902 ) ) ; +#9436 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9437 = EDGE_CURVE ( 'NONE', #68214, #66903, #72212, .T. ) ; +#9438 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999430, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#9439 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#9440 = EDGE_CURVE ( 'NONE', #76960, #36803, #19076, .T. ) ; +#9441 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #2500, .NOT_KNOWN. ) ; +#9442 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8199999999999999512, 0.000000000000000000 ) ) ; +#9443 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53547 ), #66588 ) ; +#9444 = FACE_OUTER_BOUND ( 'NONE', #73, .T. ) ; +#9445 = STYLED_ITEM ( 'NONE', ( #66385 ), #74707 ) ; +#9446 = CARTESIAN_POINT ( 'NONE', ( -0.04176633354695089700, -1.139163918933580266, 0.8100000000000000533 ) ) ; +#9447 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#9448 = LINE ( 'NONE', #63676, #66171 ) ; +#9449 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9450 = EDGE_LOOP ( 'NONE', ( #72922, #66354, #12811, #8024 ) ) ; +#9451 = FILL_AREA_STYLE ('',( #26381 ) ) ; +#9453 = PLANE ( 'NONE', #60691 ) ; +#9452 = SURFACE_STYLE_FILL_AREA ( #48860 ) ; +#9454 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999990319, -0.02000000000000000042 ) ) ; +#9455 = VECTOR ( 'NONE', #3701, 1000.000000000000000 ) ; +#9456 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852913999999999728, 0.8991599999999999593 ) ) ; +#9457 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9458 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40236 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24172, #85919, #78764 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9459 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74876 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69419, #70969, #15283 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9460 = LINE ( 'NONE', #71320, #45100 ) ; +#9461 = CARTESIAN_POINT ( 'NONE', ( 1.980973451220020110, 1.435480568464056139, -11.40565812211346142 ) ) ; +#9462 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#9463 = ORIENTED_EDGE ( 'NONE', *, *, #60081, .T. ) ; +#9464 = FILL_AREA_STYLE_COLOUR ( '', #24383 ) ; +#9465 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72735, #25792, #94170, #71737 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9467 = ADVANCED_FACE ( 'NONE', ( #34940 ), #96670, .F. ) ; +#9466 = PRESENTATION_STYLE_ASSIGNMENT (( #54519 ) ) ; +#9468 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#9469 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9470 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9471 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9472 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99305, 'distance_accuracy_value', 'NONE'); +#9473 = CARTESIAN_POINT ( 'NONE', ( 1.233333333333330284, -3.500000000000000000, 0.000000000000000000 ) ) ; +#9474 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9475 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9476 = EDGE_CURVE ( 'NONE', #3163, #16343, #18049, .T. ) ; +#9477 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9478 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9479 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9480 = AXIS2_PLACEMENT_3D ( 'NONE', #92046, #99130, #93014 ) ; +#9481 = ADVANCED_FACE ( 'NONE', ( #10327 ), #50775, .T. ) ; +#9482 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33999 ), #7775 ) ; +#9483 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#9484 = VECTOR ( 'NONE', #73881, 1000.000000000000114 ) ; +#9485 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9486 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#9487 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57738, 'distance_accuracy_value', 'NONE'); +#9488 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26200 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60407, #42549, #91504 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9489 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#9490 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.5000000000000000000, -13.54999999999999893 ) ) ; +#9491 = ORIENTED_EDGE ( 'NONE', *, *, #67367, .F. ) ; +#9492 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9493 = LINE ( 'NONE', #87177, #64862 ) ; +#9494 = DIRECTION ( 'NONE', ( 0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#9495 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74955, 'distance_accuracy_value', 'NONE'); +#9497 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9496 = CARTESIAN_POINT ( 'NONE', ( -0.02839774098039829844, -1.241062917987890257, 0.8300000000000002931 ) ) ; +#9498 = CARTESIAN_POINT ( 'NONE', ( 1.123927650580943460, -1.429931027375498154, 0.8099999999997194999 ) ) ; +#9499 = PLANE ( 'NONE', #68350 ) ; +#9500 = VECTOR ( 'NONE', #41725, 1000.000000000000000 ) ; +#9501 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9502 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1424 ) ) ; +#9503 = EDGE_CURVE ( 'NONE', #91502, #7621, #13352, .T. ) ; +#9504 = ORIENTED_EDGE ( 'NONE', *, *, #43559, .T. ) ; +#9505 = SURFACE_STYLE_FILL_AREA ( #48902 ) ; +#9506 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, -0.02000000000002725292 ) ) ; +#9507 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35717, 'distance_accuracy_value', 'NONE'); +#9508 = PRESENTATION_STYLE_ASSIGNMENT (( #64218 ) ) ; +#9509 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57408, 'distance_accuracy_value', 'NONE'); +#9510 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9511 = ADVANCED_FACE ( 'NONE', ( #82892 ), #14391, .T. ) ; +#9512 = EDGE_LOOP ( 'NONE', ( #97876, #89827, #27129, #21140 ) ) ; +#9513 = VERTEX_POINT ( 'NONE', #76718 ) ; +#9514 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#9515 = SURFACE_STYLE_USAGE ( .BOTH. , #11516 ) ; +#9516 = VECTOR ( 'NONE', #13119, 1000.000000000000000 ) ; +#9517 = ORIENTED_EDGE ( 'NONE', *, *, #53147, .F. ) ; +#9518 = EDGE_CURVE ( 'NONE', #37758, #81837, #98611, .T. ) ; +#9519 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9520 = SURFACE_STYLE_USAGE ( .BOTH. , #9006 ) ; +#9521 = AXIS2_PLACEMENT_3D ( 'NONE', #51560, #21879, #29046 ) ; +#9522 = VECTOR ( 'NONE', #61193, 1000.000000000000000 ) ; +#9523 = PRODUCT_CONTEXT ( 'NONE', #21467, 'mechanical' ) ; +#9524 = PLANE ( 'NONE', #42747 ) ; +#9525 = FILL_AREA_STYLE_COLOUR ( '', #86834 ) ; +#9527 = ORIENTED_EDGE ( 'NONE', *, *, #56228, .T. ) ; +#9526 = ORIENTED_EDGE ( 'NONE', *, *, #86213, .F. ) ; +#9528 = EDGE_CURVE ( 'NONE', #32231, #93204, #37444, .T. ) ; +#9529 = ORIENTED_EDGE ( 'NONE', *, *, #50762, .T. ) ; +#9530 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9531 = SURFACE_STYLE_USAGE ( .BOTH. , #54062 ) ; +#9532 = FILL_AREA_STYLE ('',( #79573 ) ) ; +#9533 = VERTEX_POINT ( 'NONE', #98126 ) ; +#9534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29151 ), #89510 ) ; +#9535 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9536 = ORIENTED_EDGE ( 'NONE', *, *, #86020, .T. ) ; +#9537 = VECTOR ( 'NONE', #16778, 1000.000000000000000 ) ; +#9538 = ORIENTED_EDGE ( 'NONE', *, *, #63448, .T. ) ; +#9539 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9540 = ORIENTED_EDGE ( 'NONE', *, *, #13780, .F. ) ; +#9541 = ADVANCED_FACE ( 'N', ( #99606 ), #44073, .T. ) ; +#9542 = EDGE_LOOP ( 'NONE', ( #8491, #25248, #11019, #17492 ) ) ; +#9543 = EDGE_CURVE ( 'NONE', #16606, #26314, #60442, .T. ) ; +#9544 = ORIENTED_EDGE ( 'NONE', *, *, #64243, .F. ) ; +#9545 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9546 = SURFACE_STYLE_FILL_AREA ( #94859 ) ; +#9547 = CARTESIAN_POINT ( 'NONE', ( -0.1534467802446229934, -0.9032194100038879458, 0.8299999999999999600 ) ) ; +#9548 = ORIENTED_EDGE ( 'NONE', *, *, #60266, .F. ) ; +#9550 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -0.9701298701298698424, 0.8099999999998183098 ) ) ; +#9549 = LINE ( 'NONE', #40794, #48183 ) ; +#9551 = CARTESIAN_POINT ( 'NONE', ( 0.01105796065628599986, -1.194792006717259936, 0.8299999999999999600 ) ) ; +#9552 = VERTEX_POINT ( 'NONE', #67534 ) ; +#9553 = ORIENTED_EDGE ( 'NONE', *, *, #89433, .T. ) ; +#9554 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9555 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#9556 = EDGE_CURVE ( 'NONE', #42643, #8779, #60930, .T. ) ; +#9557 = CARTESIAN_POINT ( 'NONE', ( -0.4248777619592499777, -1.223222257147859926, 0.8299999999999999600 ) ) ; +#9558 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9231 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23111, #85883, #15909 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9559 = EDGE_CURVE ( 'NONE', #44992, #28296, #62432, .T. ) ; +#9560 = SURFACE_STYLE_FILL_AREA ( #26000 ) ; +#9562 = FILL_AREA_STYLE ('',( #55636 ) ) ; +#9561 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97646 ), #39020 ) ; +#9563 = LINE ( 'NONE', #17788, #48866 ) ; +#9564 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9565 = VERTEX_POINT ( 'NONE', #48108 ) ; +#9566 = CARTESIAN_POINT ( 'NONE', ( -0.01004137219608649927, -1.188470249711290228, 0.8100000000000000533 ) ) ; +#9567 = ORIENTED_EDGE ( 'NONE', *, *, #23911, .T. ) ; +#9568 = CYLINDRICAL_SURFACE ( 'NONE', #43944, 0.09999999999999939493 ) ; +#9569 = LINE ( 'NONE', #18290, #13850 ) ; +#9570 = AXIS2_PLACEMENT_3D ( 'NONE', #66342, #42370, #73507 ) ; +#9571 = PLANE ( 'NONE', #70868 ) ; +#9573 = FILL_AREA_STYLE ('',( #72434 ) ) ; +#9572 = FILL_AREA_STYLE ('',( #63316 ) ) ; +#9574 = FILL_AREA_STYLE ('',( #55152 ) ) ; +#9575 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#9576 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9577 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#9578 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9579 = CARTESIAN_POINT ( 'NONE', ( -1.261022403107399992, -0.9825712221600161334, 0.8299999999999998490 ) ) ; +#9580 = SURFACE_SIDE_STYLE ('',( #48499 ) ) ; +#9581 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88076 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78434, #311, #70768 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9582 = FILL_AREA_STYLE ('',( #72444 ) ) ; +#9583 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60216 ), #50455 ) ; +#9584 = FACE_OUTER_BOUND ( 'NONE', #73434, .T. ) ; +#9585 = FACE_OUTER_BOUND ( 'NONE', #15858, .T. ) ; +#9586 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9587 = SURFACE_STYLE_FILL_AREA ( #95920 ) ; +#9588 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#9589 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97675 ), #57085 ) ; +#9590 = AXIS2_PLACEMENT_3D ( 'NONE', #53767, #28771, #21620 ) ; +#9592 = EDGE_CURVE ( 'NONE', #99888, #10140, #15922, .T. ) ; +#9591 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96312, 'distance_accuracy_value', 'NONE'); +#9593 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78121 ) ) ; +#9594 = ORIENTED_EDGE ( 'NONE', *, *, #86343, .F. ) ; +#9595 = DIRECTION ( 'NONE', ( 0.6625638003500460282, 0.7490054809316848417, 0.000000000000000000 ) ) ; +#9596 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#9597 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9598 = ORIENTED_EDGE ( 'NONE', *, *, #53164, .T. ) ; +#9599 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9600 = AXIS2_PLACEMENT_3D ( 'NONE', #93673, #22780, #85555 ) ; +#9601 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, -0.02000000000002515044 ) ) ; +#9602 = LINE ( 'NONE', #87290, #64605 ) ; +#9603 = SURFACE_SIDE_STYLE ('',( #70972 ) ) ; +#9604 = FACE_OUTER_BOUND ( 'NONE', #3990, .T. ) ; +#9605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21077 ), #35752 ) ; +#9606 = ORIENTED_EDGE ( 'NONE', *, *, #86570, .T. ) ; +#9607 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9608 = EDGE_CURVE ( 'NONE', #58354, #95346, #79254, .T. ) ; +#9609 = EDGE_LOOP ( 'NONE', ( #41439, #26477, #96457, #49229 ) ) ; +#9610 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51017 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5471, #11083, #73480 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9611 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#9612 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#9614 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30628 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56838, #86952, #17470 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9613 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#9615 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#9616 = CARTESIAN_POINT ( 'NONE', ( -0.1683685331939580310, -1.436594792639700024, 0.8299999999999995159 ) ) ; +#9617 = PLANE ( 'NONE', #11797 ) ; +#9618 = SURFACE_SIDE_STYLE ('',( #41869 ) ) ; +#9619 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9620 = VECTOR ( 'NONE', #9060, 1000.000000000000000 ) ; +#9621 = ORIENTED_EDGE ( 'NONE', *, *, #41965, .T. ) ; +#9622 = PLANE ( 'NONE', #27295 ) ; +#9623 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#9624 = EDGE_LOOP ( 'NONE', ( #77310, #99099, #86695, #94480 ) ) ; +#9625 = FACE_OUTER_BOUND ( 'NONE', #61970, .T. ) ; +#9626 = ORIENTED_EDGE ( 'NONE', *, *, #2235, .T. ) ; +#9628 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9627 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65109 ), #16167 ) ; +#9629 = SURFACE_SIDE_STYLE ('',( #31185 ) ) ; +#9630 = LINE ( 'NONE', #40883, #99034 ) ; +#9631 = AXIS2_PLACEMENT_3D ( 'NONE', #26676, #11730, #88947 ) ; +#9632 = FILL_AREA_STYLE ('',( #39856 ) ) ; +#9633 = SURFACE_SIDE_STYLE ('',( #79691 ) ) ; +#9634 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8100000000000000533 ) ) ; +#9635 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9636 = SURFACE_STYLE_FILL_AREA ( #94958 ) ; +#9638 = ORIENTED_EDGE ( 'NONE', *, *, #33519, .T. ) ; +#9637 = VERTEX_POINT ( 'NONE', #61930 ) ; +#9639 = ADVANCED_FACE ( 'NONE', ( #16409 ), #8199, .T. ) ; +#9640 = FILL_AREA_STYLE ('',( #55714 ) ) ; +#9641 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9642 = VERTEX_POINT ( 'NONE', #70052 ) ; +#9643 = FILL_AREA_STYLE_COLOUR ( '', #44379 ) ; +#9644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9645 = VERTEX_POINT ( 'NONE', #25163 ) ; +#9646 = EDGE_CURVE ( 'NONE', #5428, #53046, #39420, .T. ) ; +#9647 = ORIENTED_EDGE ( 'NONE', *, *, #74337, .F. ) ; +#9648 = PLANE ( 'NONE', #10552 ) ; +#9649 = FILL_AREA_STYLE ('',( #3087 ) ) ; +#9650 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.000000000000000000 ) ) ; +#9651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97727 ) ) ; +#9652 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000019540, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#9653 = ORIENTED_EDGE ( 'NONE', *, *, #75544, .T. ) ; +#9654 = ORIENTED_EDGE ( 'NONE', *, *, #87904, .T. ) ; +#9655 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72421, #31618, #87245, #16767 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9656 = ORIENTED_EDGE ( 'NONE', *, *, #33537, .T. ) ; +#9657 = ADVANCED_FACE ( 'NONE', ( #70563 ), #24655, .T. ) ; +#9658 = EDGE_CURVE ( 'NONE', #19573, #58037, #617, .T. ) ; +#9659 = STYLED_ITEM ( 'NONE', ( #85707 ), #85890 ) ; +#9660 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40458 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88253, #74443, #97849 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9661 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9664 = ADVANCED_FACE ( 'NONE', ( #3150 ), #57299, .T. ) ; +#9663 = VERTEX_POINT ( 'NONE', #96043 ) ; +#9662 = PRESENTATION_STYLE_ASSIGNMENT (( #8641 ) ) ; +#9665 = EDGE_CURVE ( 'NONE', #40536, #20680, #10715, .T. ) ; +#9666 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48906 ) ) ; +#9667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97676 ), #92854 ) ; +#9668 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#9669 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30951 ), #29354 ) ; +#9670 = FACE_OUTER_BOUND ( 'NONE', #91830, .T. ) ; +#9671 = ORIENTED_EDGE ( 'NONE', *, *, #47789, .F. ) ; +#9672 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#9673 = CARTESIAN_POINT ( 'NONE', ( -1.024015507270540803, -1.413524840751614331, 0.8099999999996837508 ) ) ; +#9674 = ORIENTED_EDGE ( 'NONE', *, *, #91793, .F. ) ; +#9675 = VECTOR ( 'NONE', #58994, 1000.000000000000000 ) ; +#9676 = SURFACE_SIDE_STYLE ('',( #15367 ) ) ; +#9677 = EDGE_CURVE ( 'NONE', #34736, #84851, #97556, .T. ) ; +#9679 = PRESENTATION_STYLE_ASSIGNMENT (( #48591 ) ) ; +#9678 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24442 ) ) ; +#9680 = SURFACE_STYLE_FILL_AREA ( #72062 ) ; +#9681 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8648700000000000276 ) ) ; +#9682 = EDGE_CURVE ( 'NONE', #94722, #97828, #81296, .T. ) ; +#9683 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#9684 = PRESENTATION_STYLE_ASSIGNMENT (( #79737 ) ) ; +#9685 = PLANE ( 'NONE', #84138 ) ; +#9686 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#9687 = AXIS2_PLACEMENT_3D ( 'NONE', #711, #55879, #14982 ) ; +#9688 = ORIENTED_EDGE ( 'NONE', *, *, #9980, .T. ) ; +#9689 = CARTESIAN_POINT ( 'NONE', ( -0.9858361255783950616, -0.9444486738239200596, 0.8300000000000000711 ) ) ; +#9690 = ORIENTED_EDGE ( 'NONE', *, *, #16702, .T. ) ; +#9691 = AXIS2_PLACEMENT_3D ( 'NONE', #972, #80618, #16758 ) ; +#9692 = SURFACE_SIDE_STYLE ('',( #47567 ) ) ; +#9693 = STYLED_ITEM ( 'NONE', ( #75342 ), #42614 ) ; +#9694 = SURFACE_STYLE_FILL_AREA ( #71051 ) ; +#9695 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.78243800000000086, 0.8648700000000000276 ) ) ; +#9696 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#9697 = SURFACE_SIDE_STYLE ('',( #79225 ) ) ; +#9698 = SURFACE_SIDE_STYLE ('',( #62925 ) ) ; +#9699 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.950000000000000178, 0.000000000000000000 ) ) ; +#9700 = VECTOR ( 'NONE', #56734, 1000.000000000000000 ) ; +#9701 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.7000000000000001776, 0.000000000000000000 ) ) ; +#9702 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27531, #35201, #12614 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9703 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9704 = PRESENTATION_STYLE_ASSIGNMENT (( #10183 ) ) ; +#9705 = FILL_AREA_STYLE ('',( #64924 ) ) ; +#9706 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11300 ), #12988 ) ; +#9707 = ORIENTED_EDGE ( 'NONE', *, *, #58113, .F. ) ; +#9708 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9709 = SURFACE_STYLE_FILL_AREA ( #56290 ) ; +#9710 = SURFACE_STYLE_USAGE ( .BOTH. , #33293 ) ; +#9712 = VECTOR ( 'NONE', #33469, 1000.000000000000000 ) ; +#9711 = LINE ( 'NONE', #3145, #1164 ) ; +#9713 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9714 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#9716 = EDGE_CURVE ( 'NONE', #93302, #59682, #79770, .T. ) ; +#9715 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32138, 'distance_accuracy_value', 'NONE'); +#9717 = ORIENTED_EDGE ( 'NONE', *, *, #64212, .F. ) ; +#9718 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#9719 = PLANE ( 'NONE', #26263 ) ; +#9720 = LINE ( 'NONE', #8699, #79162 ) ; +#9721 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#9722 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44708, #61085, #75373, #59607, #92188, #5390, #6371, #36099, #36597, #43717, #45693, #91201, #60584, #45199, #76886, #51420, #37596, #20235, #82551 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.206823832064012060E-05, 2.348066517696998170E-05, 3.424528344027769278E-05, 4.442676613306013455E-05, 5.429788834794965015E-05, 6.393571639819889147E-05, 7.352362677377814954E-05, 8.316220916426633888E-05, 9.280908540431957417E-05, 0.0001024469134545688358, 0.0001120461915498765913, 0.0001218552492073763922, 0.0001317440326062963431, 0.0001420553655807767592, 0.0001526154183617249983, 0.0001635947015071011939 ), + .UNSPECIFIED. ) ; +#9723 = FILL_AREA_STYLE_COLOUR ( '', #30578 ) ; +#9724 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#9725 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9726 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67562, #19618, #82429, #11864 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#9727 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78331 ) ) ; +#9728 = VECTOR ( 'NONE', #8561, 1000.000000000000000 ) ; +#9729 = PRESENTATION_STYLE_ASSIGNMENT (( #40983 ) ) ; +#9730 = VERTEX_POINT ( 'NONE', #26653 ) ; +#9731 = PLANE ( 'NONE', #74294 ) ; +#9732 = ORIENTED_EDGE ( 'NONE', *, *, #57733, .T. ) ; +#9733 = FILL_AREA_STYLE_COLOUR ( '', #81267 ) ; +#9734 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59267, 'distance_accuracy_value', 'NONE'); +#9735 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12942 ) ) ; +#9736 = LINE ( 'NONE', #48646, #89604 ) ; +#9737 = FILL_AREA_STYLE_COLOUR ( '', #16887 ) ; +#9738 = STYLED_ITEM ( 'NONE', ( #65988 ), #85698 ) ; +#9739 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9740 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90413 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38283, #100428, #85229 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9741 = SURFACE_SIDE_STYLE ('',( #17959 ) ) ; +#9742 = SURFACE_SIDE_STYLE ('',( #64464 ) ) ; +#9743 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78025 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36164, #13577, #53479 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9744 = ORIENTED_EDGE ( 'NONE', *, *, #86243, .T. ) ; +#9745 = FILL_AREA_STYLE ('',( #79795 ) ) ; +#9746 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#9747 = LINE ( 'NONE', #9243, #35663 ) ; +#9748 = VECTOR ( 'NONE', #20023, 1000.000000000000000 ) ; +#9749 = PRESENTATION_STYLE_ASSIGNMENT (( #64469 ) ) ; +#9750 = ORIENTED_EDGE ( 'NONE', *, *, #33499, .T. ) ; +#9751 = SURFACE_STYLE_FILL_AREA ( #42501 ) ; +#9752 = CYLINDRICAL_SURFACE ( 'NONE', #60249, 1.462498829941430323 ) ; +#9753 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40834 ) ) ; +#9754 = ORIENTED_EDGE ( 'NONE', *, *, #34163, .T. ) ; +#9755 = FACE_OUTER_BOUND ( 'NONE', #31482, .T. ) ; +#9756 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9757 = DIRECTION ( 'NONE', ( 0.7071072811865701802, -0.7071062811861712483, 0.000000000000000000 ) ) ; +#9758 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9759 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15714 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81545, #45664, #14009 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9760 = VERTEX_POINT ( 'NONE', #57821 ) ; +#9761 = LINE ( 'NONE', #87954, #26171 ) ; +#9762 = SURFACE_SIDE_STYLE ('',( #18499 ) ) ; +#9763 = VERTEX_POINT ( 'NONE', #42471 ) ; +#9764 = FILL_AREA_STYLE ('',( #87453 ) ) ; +#9765 = PRESENTATION_STYLE_ASSIGNMENT (( #49172 ) ) ; +#9766 = VERTEX_POINT ( 'NONE', #89420 ) ; +#9767 = LINE ( 'NONE', #23674, #49461 ) ; +#9768 = SURFACE_STYLE_FILL_AREA ( #2211 ) ; +#9769 = VECTOR ( 'NONE', #96802, 1000.000000000000000 ) ; +#9770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9771 = VERTEX_POINT ( 'NONE', #56301 ) ; +#9773 = EDGE_LOOP ( 'NONE', ( #24958, #4705, #95563, #2127 ) ) ; +#9772 = VERTEX_POINT ( 'NONE', #9718 ) ; +#9774 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8648700000000000276 ) ) ; +#9775 = VERTEX_POINT ( 'NONE', #18958 ) ; +#9776 = CARTESIAN_POINT ( 'NONE', ( 1.841287855068439949, -1.152628822534790043, 0.8299999999999995159 ) ) ; +#9777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49027 ), #78313 ) ; +#9778 = ORIENTED_EDGE ( 'NONE', *, *, #41856, .F. ) ; +#9780 = ORIENTED_EDGE ( 'NONE', *, *, #76609, .T. ) ; +#9779 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9781 = ADVANCED_FACE ( 'NONE', ( #73604 ), #19476, .T. ) ; +#9782 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9783 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9784 = PRESENTATION_STYLE_ASSIGNMENT (( #63523 ) ) ; +#9785 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#9786 = ORIENTED_EDGE ( 'NONE', *, *, #56882, .F. ) ; +#9787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9788 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004386000000000223, 0.8991599999999999593 ) ) ; +#9789 = FILL_AREA_STYLE_COLOUR ( '', #36244 ) ; +#9790 = ORIENTED_EDGE ( 'NONE', *, *, #35008, .F. ) ; +#9791 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9792 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9793 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9794 = LINE ( 'NONE', #41053, #53213 ) ; +#9795 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9796 = ORIENTED_EDGE ( 'NONE', *, *, #95624, .T. ) ; +#9797 = FACE_OUTER_BOUND ( 'NONE', #17092, .T. ) ; +#9798 = ORIENTED_EDGE ( 'NONE', *, *, #54066, .F. ) ; +#9799 = LINE ( 'NONE', #19555, #34840 ) ; +#9800 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65341 ), #66945 ) ; +#9801 = ADVANCED_FACE ( 'N', ( #59832 ), #75600, .T. ) ; +#9802 = AXIS2_PLACEMENT_3D ( 'NONE', #54349, #61522, #206 ) ; +#9803 = STYLED_ITEM ( 'NONE', ( #52498 ), #95125 ) ; +#9804 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9805 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#9806 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8648700000000000276 ) ) ; +#9807 = STYLED_ITEM ( 'NONE', ( #96880 ), #57702 ) ; +#9808 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#9809 = STYLED_ITEM ( 'NONE', ( #94118 ), #94546 ) ; +#9810 = SURFACE_STYLE_USAGE ( .BOTH. , #87011 ) ; +#9811 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#9812 = PLANE ( 'NONE', #64319 ) ; +#9813 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21279, #44739, #24332 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9814 = CARTESIAN_POINT ( 'NONE', ( -0.9354363632813189611, -1.053930089500670020, 0.8299999999999999600 ) ) ; +#9815 = STYLED_ITEM ( 'NONE', ( #93008 ), #65840 ) ; +#9816 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#9817 = ORIENTED_EDGE ( 'NONE', *, *, #2766, .F. ) ; +#9818 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#9819 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9820 = DIRECTION ( 'NONE', ( -0.7071090539100516326, -0.7071045084557385785, 0.000000000000000000 ) ) ; +#9821 = LINE ( 'NONE', #722, #54265 ) ; +#9822 = VERTEX_POINT ( 'NONE', #90417 ) ; +#9823 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#9824 = LINE ( 'NONE', #79361, #5477 ) ; +#9825 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62735 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98612, #91045, #75717 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9827 = CARTESIAN_POINT ( 'NONE', ( 5.823359999999999204, 9.085504000000002023, 0.8648700000000000276 ) ) ; +#9826 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#9828 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7030, 'distance_accuracy_value', 'NONE'); +#9829 = STYLED_ITEM ( 'NONE', ( #91494 ), #69349 ) ; +#9830 = PRESENTATION_STYLE_ASSIGNMENT (( #47714 ) ) ; +#9831 = CARTESIAN_POINT ( 'NONE', ( 0.2732652112985429760, -1.367023653493709912, 0.8299999999999999600 ) ) ; +#9832 = CARTESIAN_POINT ( 'NONE', ( -1.158596477595430052, -1.445196667902379994, 0.8299999999999998490 ) ) ; +#9833 = FILL_AREA_STYLE_COLOUR ( '', #100711 ) ; +#9834 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8648700000000000276 ) ) ; +#9835 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9836 = EDGE_CURVE ( 'NONE', #13836, #37874, #7458, .T. ) ; +#9837 = ORIENTED_EDGE ( 'NONE', *, *, #82446, .F. ) ; +#9838 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9839 = FILL_AREA_STYLE ('',( #40585 ) ) ; +#9840 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9841 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#9842 = PRESENTATION_STYLE_ASSIGNMENT (( #66071 ) ) ; +#9843 = FACE_OUTER_BOUND ( 'NONE', #50506, .T. ) ; +#9844 = PLANE ( 'NONE', #45714 ) ; +#9845 = LINE ( 'NONE', #80913, #79528 ) ; +#9846 = SURFACE_STYLE_USAGE ( .BOTH. , #17567 ) ; +#9847 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53953 ) ) ; +#9848 = CARTESIAN_POINT ( 'NONE', ( 1.044215815879510068, -1.351519064127929992, 0.8299999999999999600 ) ) ; +#9849 = SURFACE_STYLE_FILL_AREA ( #96186 ) ; +#9850 = ORIENTED_EDGE ( 'NONE', *, *, #91463, .F. ) ; +#9851 = ORIENTED_EDGE ( 'NONE', *, *, #15057, .F. ) ; +#9852 = VECTOR ( 'NONE', #66711, 1000.000000000000000 ) ; +#9853 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9854 = FILL_AREA_STYLE ('',( #65078 ) ) ; +#9855 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9856 = PRESENTATION_STYLE_ASSIGNMENT (( #78888 ) ) ; +#9857 = LINE ( 'NONE', #3797, #60776 ) ; +#9858 = VERTEX_POINT ( 'NONE', #51656 ) ; +#9859 = FILL_AREA_STYLE_COLOUR ( '', #40610 ) ; +#9861 = EDGE_CURVE ( 'NONE', #36781, #6840, #75117, .T. ) ; +#9860 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#9862 = FILL_AREA_STYLE_COLOUR ( '', #75367 ) ; +#9863 = AXIS2_PLACEMENT_3D ( 'NONE', #40563, #56405, #88010 ) ; +#9864 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33852, #9756, #79291 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9865 = ORIENTED_EDGE ( 'NONE', *, *, #46091, .T. ) ; +#9866 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#9867 = EDGE_CURVE ( 'NONE', #406, #47283, #5613, .T. ) ; +#9868 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32851 ), #80098 ) ; +#9869 = PRESENTATION_STYLE_ASSIGNMENT (( #48794 ) ) ; +#9870 = AXIS2_PLACEMENT_3D ( 'NONE', #20589, #99120, #21105 ) ; +#9871 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.000000000000000000 ) ) ; +#9872 = PRESENTATION_STYLE_ASSIGNMENT (( #27830 ) ) ; +#9873 = ORIENTED_EDGE ( 'NONE', *, *, #81891, .F. ) ; +#9874 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47422 ) ) ; +#9875 = SURFACE_STYLE_USAGE ( .BOTH. , #80955 ) ; +#9876 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19283, 'distance_accuracy_value', 'NONE'); +#9877 = EDGE_CURVE ( 'NONE', #96693, #22571, #89917, .T. ) ; +#9878 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70305 ), #34495 ) ; +#9879 = ORIENTED_EDGE ( 'NONE', *, *, #43970, .F. ) ; +#9880 = EDGE_CURVE ( 'NONE', #93048, #24848, #100833, .T. ) ; +#9881 = LINE ( 'NONE', #41135, #43190 ) ; +#9882 = LINE ( 'NONE', #32965, #83160 ) ; +#9883 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999467, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#9884 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#9885 = FILL_AREA_STYLE ('',( #55972 ) ) ; +#9886 = FILL_AREA_STYLE ('',( #56491 ) ) ; +#9887 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #35434, #82894 ) ; +#9888 = VECTOR ( 'NONE', #10187, 1000.000000000000000 ) ; +#9889 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9890 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#9891 = ORIENTED_EDGE ( 'NONE', *, *, #78570, .T. ) ; +#9892 = VERTEX_POINT ( 'NONE', #36806 ) ; +#9893 = ADVANCED_FACE ( 'NONE', ( #52146 ), #27664, .T. ) ; +#9894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9286, 'distance_accuracy_value', 'NONE'); +#9895 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#9896 = SURFACE_STYLE_USAGE ( .BOTH. , #95724 ) ; +#9897 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9898 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#9899 = ORIENTED_EDGE ( 'NONE', *, *, #80621, .F. ) ; +#9900 = SURFACE_SIDE_STYLE ('',( #18120 ) ) ; +#9901 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9902 = STYLED_ITEM ( 'NONE', ( #88179 ), #51775 ) ; +#9903 = ORIENTED_EDGE ( 'NONE', *, *, #29081, .T. ) ; +#9905 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9904 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.300000000000000266, 0.8299999999999999600 ) ) ; +#9906 = ORIENTED_EDGE ( 'NONE', *, *, #86276, .T. ) ; +#9907 = VECTOR ( 'NONE', #49424, 1000.000000000000000 ) ; +#9908 = ORIENTED_EDGE ( 'NONE', *, *, #99294, .F. ) ; +#9909 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.9000000000000014655, 8.225148568024281774E-79 ) ) ; +#9910 = ADVANCED_FACE ( 'NONE', ( #17200 ), #24918, .T. ) ; +#9911 = SURFACE_STYLE_FILL_AREA ( #25854 ) ; +#9912 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9914 = ORIENTED_EDGE ( 'NONE', *, *, #90577, .F. ) ; +#9913 = VECTOR ( 'NONE', #58496, 1000.000000000000000 ) ; +#9915 = SURFACE_STYLE_FILL_AREA ( #47810 ) ; +#9916 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#9917 = ORIENTED_EDGE ( 'NONE', *, *, #94144, .F. ) ; +#9918 = CARTESIAN_POINT ( 'NONE', ( 1.334872846471060193, -1.409018172687890091, 0.8299999999999999600 ) ) ; +#9919 = VERTEX_POINT ( 'NONE', #49373 ) ; +#9920 = VERTEX_POINT ( 'NONE', #9970 ) ; +#9922 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#9921 = PLANE ( 'NONE', #55870 ) ; +#9923 = CARTESIAN_POINT ( 'NONE', ( -1.266878993523750108, -1.195322104373929939, 0.8100000000000000533 ) ) ; +#9924 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#9925 = LINE ( 'NONE', #73825, #69286 ) ; +#9926 = STYLED_ITEM ( 'NONE', ( #95516 ), #18389 ) ; +#9927 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89899 ), #5105 ) ; +#9928 = FILL_AREA_STYLE ('',( #79995 ) ) ; +#9929 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9930 = CARTESIAN_POINT ( 'NONE', ( -0.04997673550079750199, -1.145059460293619935, 0.8299999999999999600 ) ) ; +#9931 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100947 ) ; +#9932 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#9933 = CARTESIAN_POINT ( 'NONE', ( -2.523820061220085176, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#9934 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80167 ) ) ; +#9935 = VECTOR ( 'NONE', #12360, 1000.000000000000000 ) ; +#9936 = ORIENTED_EDGE ( 'NONE', *, *, #80617, .F. ) ; +#9937 = EDGE_CURVE ( 'NONE', #42723, #94979, #81343, .T. ) ; +#9938 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#9939 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#9941 = PRESENTATION_STYLE_ASSIGNMENT (( #40695 ) ) ; +#9940 = SURFACE_SIDE_STYLE ('',( #9452 ) ) ; +#9943 = LINE ( 'NONE', #41198, #4079 ) ; +#9942 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71262 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55135, #20780, #83586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#9944 = SURFACE_STYLE_FILL_AREA ( #80008 ) ; +#9945 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#9946 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9947 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#9948 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#9949 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9950 = EDGE_CURVE ( 'NONE', #63952, #39755, #368, .T. ) ; +#9951 = ORIENTED_EDGE ( 'NONE', *, *, #84205, .T. ) ; +#9952 = CARTESIAN_POINT ( 'NONE', ( 3.843461124874956614, 7.105605124874957212, 0.8648700000000000276 ) ) ; +#9953 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #687, 'distance_accuracy_value', 'NONE'); +#9954 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#9955 = FILL_AREA_STYLE ('',( #40205 ) ) ; +#9956 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9957 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#9958 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9959 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73682 ), #62251 ) ; +#9960 = LINE ( 'NONE', #80022, #26879 ) ; +#9961 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#9962 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9963 = PRESENTATION_STYLE_ASSIGNMENT (( #73860 ) ) ; +#9964 = FILL_AREA_STYLE_COLOUR ( '', #42459 ) ; +#9965 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#9966 = SURFACE_STYLE_FILL_AREA ( #48884 ) ; +#9967 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#9968 = MANIFOLD_SOLID_BREP ( 'ÊäÈë183', #60032 ) ; +#9969 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -1.899999999999999911, 0.000000000000000000 ) ) ; +#9970 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#9971 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9972 = ORIENTED_EDGE ( 'NONE', *, *, #96723, .T. ) ; +#9973 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 0.1000000000000000056, -11.57000000000000028 ) ) ; +#9974 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9975 = SURFACE_SIDE_STYLE ('',( #35598 ) ) ; +#9976 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#9977 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.266666666666667052, 3.495651678170177615E-76 ) ) ; +#9978 = FACE_OUTER_BOUND ( 'NONE', #8730, .T. ) ; +#9979 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#9980 = EDGE_CURVE ( 'NONE', #18757, #80604, #31537, .T. ) ; +#9981 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9982 = ORIENTED_EDGE ( 'NONE', *, *, #50, .F. ) ; +#9983 = FILL_AREA_STYLE_COLOUR ( '', #53903 ) ; +#9984 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19852 ), #45894 ) ; +#9985 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#9986 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#9987 = ADVANCED_FACE ( 'NONE', ( #66686 ), #35085, .F. ) ; +#9988 = ORIENTED_EDGE ( 'NONE', *, *, #81953, .F. ) ; +#9989 = VERTEX_POINT ( 'NONE', #74864 ) ; +#9990 = EDGE_CURVE ( 'NONE', #95534, #59128, #43207, .T. ) ; +#9991 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16611 ), #23151 ) ; +#9992 = VECTOR ( 'NONE', #41884, 1000.000000000000000 ) ; +#9993 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#9994 = PLANE ( 'NONE', #63796 ) ; +#9995 = ORIENTED_EDGE ( 'NONE', *, *, #90955, .F. ) ; +#9996 = LINE ( 'NONE', #8492, #59192 ) ; +#9997 = ADVANCED_FACE ( 'NONE', ( #67190 ), #12486, .T. ) ; +#9998 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#9999 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10000 = FILL_AREA_STYLE_COLOUR ( '', #87189 ) ; +#10001 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42686 ), #78594 ) ; +#10002 = VECTOR ( 'NONE', #95418, 1000.000000000000000 ) ; +#10003 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10004 = PRODUCT_CONTEXT ( 'NONE', #33269, 'mechanical' ) ; +#10005 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10006 = CARTESIAN_POINT ( 'NONE', ( 0.9588526530481741306, -1.318629679536721611, 0.8099999999997893330 ) ) ; +#10008 = ORIENTED_EDGE ( 'NONE', *, *, #91675, .T. ) ; +#10007 = ORIENTED_EDGE ( 'NONE', *, *, #35753, .F. ) ; +#10009 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10010 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32680 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22201, #98230, #36544 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10011 = EDGE_LOOP ( 'NONE', ( #6793, #3547, #12396, #41172 ) ) ; +#10012 = FILL_AREA_STYLE ('',( #95338 ) ) ; +#10013 = EDGE_CURVE ( 'NONE', #71466, #68510, #10979, .T. ) ; +#10014 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33798, 'distance_accuracy_value', 'NONE'); +#10015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93221 ), #11624 ) ; +#10017 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#10016 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -1.626303258728260102E-16 ) ) ; +#10018 = ORIENTED_EDGE ( 'NONE', *, *, #21284, .F. ) ; +#10019 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18244 ), #83516 ) ; +#10020 = EDGE_CURVE ( 'NONE', #31497, #10525, #3429, .T. ) ; +#10021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10022 = VERTEX_POINT ( 'NONE', #96806 ) ; +#10023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70447 ), #78618 ) ; +#10024 = ORIENTED_EDGE ( 'NONE', *, *, #98185, .F. ) ; +#10026 = PLANE ( 'NONE', #85292 ) ; +#10025 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8648700000000000276 ) ) ; +#10027 = VERTEX_POINT ( 'NONE', #52906 ) ; +#10028 = ORIENTED_EDGE ( 'NONE', *, *, #43941, .T. ) ; +#10029 = PRESENTATION_STYLE_ASSIGNMENT (( #34641 ) ) ; +#10030 = EDGE_CURVE ( 'NONE', #83808, #72170, #45679, .T. ) ; +#10031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10032 = LINE ( 'NONE', #40285, #66802 ) ; +#10033 = EDGE_CURVE ( 'NONE', #17366, #61999, #5372, .T. ) ; +#10034 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10035 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8426 ), #14952 ) ; +#10037 = ORIENTED_EDGE ( 'NONE', *, *, #13869, .T. ) ; +#10036 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#10038 = SURFACE_STYLE_FILL_AREA ( #65257 ) ; +#10039 = ORIENTED_EDGE ( 'NONE', *, *, #50698, .T. ) ; +#10040 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10041 = CARTESIAN_POINT ( 'NONE', ( 0.08314493404879109983, -1.269147371132220314, 0.8299999999999999600 ) ) ; +#10043 = VERTEX_POINT ( 'NONE', #92648 ) ; +#10042 = STYLED_ITEM ( 'NONE', ( #10876 ), #52532 ) ; +#10044 = ORIENTED_EDGE ( 'NONE', *, *, #55286, .T. ) ; +#10045 = LINE ( 'NONE', #55628, #57108 ) ; +#10046 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 4.135756999999999906, 0.8648700000000000276 ) ) ; +#10047 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#10048 = PRESENTATION_STYLE_ASSIGNMENT (( #26996 ) ) ; +#10050 = VECTOR ( 'NONE', #7630, 1000.000000000000114 ) ; +#10049 = LINE ( 'NONE', #47946, #82059 ) ; +#10051 = PLANE ( 'NONE', #90064 ) ; +#10052 = FACE_OUTER_BOUND ( 'NONE', #45381, .T. ) ; +#10053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8217, 'distance_accuracy_value', 'NONE'); +#10054 = VERTEX_POINT ( 'NONE', #30369 ) ; +#10055 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.05000000000000000278, 0.2100000000000000200 ) ) ; +#10056 = EDGE_CURVE ( 'NONE', #86973, #96056, #46187, .T. ) ; +#10057 = VERTEX_POINT ( 'NONE', #91667 ) ; +#10058 = STYLED_ITEM ( 'NONE', ( #28931 ), #82005 ) ; +#10059 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23207 ) ) ; +#10060 = FILL_AREA_STYLE ('',( #62285 ) ) ; +#10061 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10062 = PRESENTATION_STYLE_ASSIGNMENT (( #11074 ) ) ; +#10063 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10064 = SURFACE_STYLE_USAGE ( .BOTH. , #50006 ) ; +#10065 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#10066 = SURFACE_SIDE_STYLE ('',( #72437 ) ) ; +#10067 = EDGE_CURVE ( 'NONE', #51626, #23955, #67674, .T. ) ; +#10068 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10069 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#10070 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10071 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#10072 = EDGE_CURVE ( 'NONE', #19800, #7585, #98761, .T. ) ; +#10073 = AXIS2_PLACEMENT_3D ( 'NONE', #57384, #73684, #3733 ) ; +#10074 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#10075 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21607 ), #67229 ) ; +#10076 = PLANE ( 'NONE', #71367 ) ; +#10077 = SURFACE_SIDE_STYLE ('',( #57693 ) ) ; +#10078 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81484 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99182, #43618, #20143 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10079 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25530 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44299, #5470, #84131 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10080 = AXIS2_PLACEMENT_3D ( 'NONE', #37507, #68101, #84449 ) ; +#10081 = ORIENTED_EDGE ( 'NONE', *, *, #27819, .F. ) ; +#10082 = FACE_OUTER_BOUND ( 'NONE', #19885, .T. ) ; +#10083 = CARTESIAN_POINT ( 'NONE', ( 1.635208922267139986, -0.9074576374047380600, 0.8100000000000000533 ) ) ; +#10084 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41512, 'distance_accuracy_value', 'NONE'); +#10085 = ORIENTED_EDGE ( 'NONE', *, *, #12185, .F. ) ; +#10087 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20579, 'distance_accuracy_value', 'NONE'); +#10086 = SURFACE_SIDE_STYLE ('',( #48517 ) ) ; +#10088 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139847999999999750, 0.8648700000000000276 ) ) ; +#10089 = VECTOR ( 'NONE', #66218, 1000.000000000000000 ) ; +#10090 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2784314575050761964, -0.1458578643762690474 ) ) ; +#10091 = CARTESIAN_POINT ( 'NONE', ( 1.698015391961940068, -0.9623926821384259922, 0.8100000000000006084 ) ) ; +#10092 = EDGE_CURVE ( 'NONE', #18739, #77581, #83533, .T. ) ; +#10093 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10094 = ORIENTED_EDGE ( 'NONE', *, *, #93970, .F. ) ; +#10095 = ORIENTED_EDGE ( 'NONE', *, *, #84964, .T. ) ; +#10096 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83176, 'distance_accuracy_value', 'NONE'); +#10097 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10098 = SURFACE_STYLE_USAGE ( .BOTH. , #2051 ) ; +#10099 = FILL_AREA_STYLE ('',( #3569 ) ) ; +#10100 = LINE ( 'NONE', #41368, #71370 ) ; +#10101 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10102 = FILL_AREA_STYLE ('',( #26553 ) ) ; +#10103 = ORIENTED_EDGE ( 'NONE', *, *, #81733, .T. ) ; +#10104 = PRESENTATION_STYLE_ASSIGNMENT (( #80184 ) ) ; +#10105 = SURFACE_STYLE_FILL_AREA ( #49038 ) ; +#10106 = ORIENTED_EDGE ( 'NONE', *, *, #57054, .F. ) ; +#10107 = PRESENTATION_STYLE_ASSIGNMENT (( #87314 ) ) ; +#10108 = ADVANCED_FACE ( 'NONE', ( #68678 ), #85017, .T. ) ; +#10109 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10110 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24903 ) ) ; +#10111 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#10112 = VERTEX_POINT ( 'NONE', #100720 ) ; +#10113 = FILL_AREA_STYLE ('',( #50067 ) ) ; +#10114 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#10115 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 15.15000000000000036, 0.000000000000000000 ) ) ; +#10116 = FILL_AREA_STYLE_COLOUR ( '', #88634 ) ; +#10117 = DIRECTION ( 'NONE', ( -1.836909530733570078E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#10118 = SURFACE_STYLE_USAGE ( .BOTH. , #88336 ) ; +#10119 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10121 = ORIENTED_EDGE ( 'NONE', *, *, #22320, .F. ) ; +#10120 = ORIENTED_EDGE ( 'NONE', *, *, #24054, .T. ) ; +#10122 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#10123 = ORIENTED_EDGE ( 'NONE', *, *, #53099, .T. ) ; +#10124 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10125 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69375 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100325, #1890, #72318 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10126 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3300 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69545, #13882, #93003 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10127 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10128 = VERTEX_POINT ( 'NONE', #29403 ) ; +#10129 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49604, #50125, #65389, #73073, #81264, #17907, #3631, #80749, #10683, #41438, #9689, #57271, #11186, #56779, #73575, #72555, #89392, #33781, #97014 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.283604389317646688E-05, 4.478221093118360410E-05, 6.621287096865391094E-05, 8.708286053616611942E-05, 0.0001074236228577663449, 0.0001271414675467349379, 0.0001466721859428478511, 0.0001659572734257095609, 0.0001851366268558017744, 0.0002043346130818336445, 0.0002236332143170293926, 0.0002432419607417065927, 0.0002635504721856779639, 0.0002848430484330230104, 0.0003074973376798120100, 0.0003314900864579825774 ), + .UNSPECIFIED. ) ; +#10130 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86124, #15650, #61173, #92270 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#10131 = ORIENTED_EDGE ( 'NONE', *, *, #17199, .T. ) ; +#10132 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10133 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10134 = SURFACE_SIDE_STYLE ('',( #97488 ) ) ; +#10135 = CARTESIAN_POINT ( 'NONE', ( -0.2223607051232819876, -1.054251812769849916, 0.8300000000000000711 ) ) ; +#10137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10136 = FILL_AREA_STYLE_COLOUR ( '', #77386 ) ; +#10138 = FACE_OUTER_BOUND ( 'NONE', #57930, .T. ) ; +#10139 = VERTEX_POINT ( 'NONE', #30898 ) ; +#10140 = VERTEX_POINT ( 'NONE', #75361 ) ; +#10141 = PRESENTATION_STYLE_ASSIGNMENT (( #88357 ) ) ; +#10142 = ORIENTED_EDGE ( 'NONE', *, *, #12552, .F. ) ; +#10143 = VECTOR ( 'NONE', #40869, 1000.000000000000000 ) ; +#10144 = FILL_AREA_STYLE ('',( #58759 ) ) ; +#10145 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91780 ), #461 ) ; +#10146 = EDGE_CURVE ( 'NONE', #76911, #43057, #62081, .T. ) ; +#10148 = ORIENTED_EDGE ( 'NONE', *, *, #207, .F. ) ; +#10147 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10149 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91711 ) ) ; +#10150 = CIRCLE ( 'NONE', #59209, 0.009999999999999998473 ) ; +#10151 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#10152 = PRESENTATION_STYLE_ASSIGNMENT (( #86865 ) ) ; +#10153 = ORIENTED_EDGE ( 'NONE', *, *, #38653, .F. ) ; +#10154 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10155 = LINE ( 'NONE', #65903, #99726 ) ; +#10156 = ORIENTED_EDGE ( 'NONE', *, *, #9264, .T. ) ; +#10157 = SURFACE_SIDE_STYLE ('',( #63896 ) ) ; +#10158 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10159 = CARTESIAN_POINT ( 'NONE', ( -1.266878993523750108, -1.195322104373929939, 0.8300000000000000711 ) ) ; +#10160 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#10161 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#10163 = SURFACE_STYLE_USAGE ( .BOTH. , #81259 ) ; +#10162 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#10164 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#10165 = ORIENTED_EDGE ( 'NONE', *, *, #96811, .T. ) ; +#10166 = EDGE_CURVE ( 'NONE', #66478, #73043, #85526, .T. ) ; +#10167 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.700000000000000178, 1.158998207294579771E-78 ) ) ; +#10168 = EDGE_LOOP ( 'NONE', ( #70118, #20538, #31203, #53268, #90277, #55306 ) ) ; +#10169 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10170 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10171 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#10172 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#10173 = FILL_AREA_STYLE_COLOUR ( '', #100611 ) ; +#10174 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10175 = PRESENTATION_STYLE_ASSIGNMENT (( #89892 ) ) ; +#10176 = FACE_OUTER_BOUND ( 'NONE', #82084, .T. ) ; +#10177 = LINE ( 'NONE', #2139, #10751 ) ; +#10179 = EDGE_CURVE ( 'NONE', #68821, #7067, #84835, .T. ) ; +#10178 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10180 = VECTOR ( 'NONE', #71745, 999.9999999999998863 ) ; +#10181 = SURFACE_STYLE_USAGE ( .BOTH. , #73589 ) ; +#10182 = STYLED_ITEM ( 'NONE', ( #1855 ), #47175 ) ; +#10183 = SURFACE_STYLE_USAGE ( .BOTH. , #8182 ) ; +#10184 = SURFACE_STYLE_FILL_AREA ( #56794 ) ; +#10185 = EDGE_LOOP ( 'NONE', ( #71866, #52981, #68635, #6031 ) ) ; +#10188 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10187 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10186 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85272 ) ) ; +#10189 = EDGE_CURVE ( 'NONE', #79538, #94737, #99470, .T. ) ; +#10190 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8648700000000000276 ) ) ; +#10191 = CIRCLE ( 'NONE', #33120, 0.009999999999999998473 ) ; +#10192 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#10193 = ADVANCED_FACE ( 'NONE', ( #21234 ), #60571, .T. ) ; +#10195 = ORIENTED_EDGE ( 'NONE', *, *, #19993, .T. ) ; +#10194 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10196 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#10197 = CARTESIAN_POINT ( 'NONE', ( -1.019254590033279895, -1.033922635360990050, 0.8299999999999999600 ) ) ; +#10198 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10199 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75534 ), #28247 ) ; +#10200 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10201 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.850000000000000089, 0.000000000000000000 ) ) ; +#10202 = LINE ( 'NONE', #76110, #95539 ) ; +#10204 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10203 = VECTOR ( 'NONE', #34172, 1000.000000000000000 ) ; +#10205 = ADVANCED_FACE ( 'NONE', ( #71221 ), #70710, .T. ) ; +#10207 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64192 ), #15145 ) ; +#10206 = SURFACE_STYLE_USAGE ( .BOTH. , #48120 ) ; +#10208 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84207, 'distance_accuracy_value', 'NONE'); +#10209 = EDGE_CURVE ( 'NONE', #41395, #78794, #53710, .T. ) ; +#10210 = AXIS2_PLACEMENT_3D ( 'NONE', #61348, #22499, #87307 ) ; +#10211 = LINE ( 'NONE', #87920, #27427 ) ; +#10212 = SURFACE_STYLE_FILL_AREA ( #1669 ) ; +#10213 = ORIENTED_EDGE ( 'NONE', *, *, #98320, .T. ) ; +#10214 = ORIENTED_EDGE ( 'NONE', *, *, #5479, .T. ) ; +#10215 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#10216 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23602, 'distance_accuracy_value', 'NONE'); +#10217 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33234, 'distance_accuracy_value', 'NONE'); +#10218 = ADVANCED_FACE ( 'NONE', ( #69506 ), #30202, .F. ) ; +#10219 = EDGE_CURVE ( 'NONE', #1795, #84768, #76184, .T. ) ; +#10220 = PLANE ( 'NONE', #9631 ) ; +#10221 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#10222 = PRESENTATION_STYLE_ASSIGNMENT (( #50174 ) ) ; +#10223 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#10224 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#10225 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, -3.099999999999992095, 0.000000000000000000 ) ) ; +#10226 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10227 = SURFACE_STYLE_FILL_AREA ( #95062 ) ; +#10228 = ORIENTED_EDGE ( 'NONE', *, *, #71541, .F. ) ; +#10229 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#10230 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10231 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#10232 = VERTEX_POINT ( 'NONE', #37895 ) ; +#10233 = EDGE_CURVE ( 'NONE', #45362, #74243, #54750, .T. ) ; +#10234 = CARTESIAN_POINT ( 'NONE', ( -0.8193368432721279682, 0.5992714337669160507, 0.8100000000000000533 ) ) ; +#10235 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60869 ), #80398 ) ; +#10236 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#10237 = EDGE_LOOP ( 'NONE', ( #69560, #72917, #18138, #64925 ) ) ; +#10238 = SURFACE_SIDE_STYLE ('',( #3679 ) ) ; +#10239 = EDGE_CURVE ( 'NONE', #50459, #14967, #91998, .T. ) ; +#10240 = FILL_AREA_STYLE ('',( #17474 ) ) ; +#10241 = LINE ( 'NONE', #87950, #88311 ) ; +#10242 = LINE ( 'NONE', #88968, #65939 ) ; +#10244 = VERTEX_POINT ( 'NONE', #5691 ) ; +#10243 = CIRCLE ( 'NONE', #31552, 0.009999999999999998473 ) ; +#10245 = DIRECTION ( 'NONE', ( 0.7071067811865489050, 0.7071067811865462405, 0.000000000000000000 ) ) ; +#10246 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10247 = ORIENTED_EDGE ( 'NONE', *, *, #98465, .T. ) ; +#10248 = ORIENTED_EDGE ( 'NONE', *, *, #57501, .T. ) ; +#10249 = FILL_AREA_STYLE_COLOUR ( '', #49750 ) ; +#10250 = DIRECTION ( 'NONE', ( 0.000000000000000000, -4.266452400824600274E-34, -1.000000000000000000 ) ) ; +#10251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10252 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10253 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#10254 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10255 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#10256 = ORIENTED_EDGE ( 'NONE', *, *, #39923, .F. ) ; +#10258 = EDGE_LOOP ( 'NONE', ( #70375, #93315, #56754, #25297 ) ) ; +#10257 = VERTEX_POINT ( 'NONE', #15884 ) ; +#10259 = VECTOR ( 'NONE', #35213, 1000.000000000000000 ) ; +#10260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8654 ), #25125 ) ; +#10261 = ORIENTED_EDGE ( 'NONE', *, *, #74037, .T. ) ; +#10262 = EDGE_CURVE ( 'NONE', #18656, #18005, #1013, .T. ) ; +#10263 = ORIENTED_EDGE ( 'NONE', *, *, #556, .T. ) ; +#10265 = ORIENTED_EDGE ( 'NONE', *, *, #9503, .F. ) ; +#10264 = SURFACE_STYLE_FILL_AREA ( #48691 ) ; +#10266 = FILL_AREA_STYLE_COLOUR ( '', #37747 ) ; +#10268 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10267 = VECTOR ( 'NONE', #38806, 1000.000000000000114 ) ; +#10269 = AXIS2_PLACEMENT_3D ( 'NONE', #66088, #96687, #3302 ) ; +#10270 = SURFACE_STYLE_FILL_AREA ( #51210 ) ; +#10271 = VERTEX_POINT ( 'NONE', #15375 ) ; +#10273 = EDGE_CURVE ( 'NONE', #82873, #99343, #47302, .T. ) ; +#10272 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#10275 = PLANE ( 'NONE', #2745 ) ; +#10274 = VECTOR ( 'NONE', #66678, 1000.000000000000000 ) ; +#10276 = FILL_AREA_STYLE_COLOUR ( '', #44359 ) ; +#10277 = ORIENTED_EDGE ( 'NONE', *, *, #91221, .F. ) ; +#10278 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10279 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#10281 = VECTOR ( 'NONE', #28378, 1000.000000000000000 ) ; +#10280 = STYLED_ITEM ( 'NONE', ( #24713 ), #37894 ) ; +#10282 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44602 ) ) ; +#10283 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#10284 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#10285 = ORIENTED_EDGE ( 'NONE', *, *, #97454, .F. ) ; +#10286 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#10287 = AXIS2_PLACEMENT_3D ( 'NONE', #71307, #80488, #95762 ) ; +#10288 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#10289 = VECTOR ( 'NONE', #12966, 1000.000000000000000 ) ; +#10290 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54430 ) ) ; +#10291 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10292 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146561861, 0.3100465759269649957, 0.8100000000000000533 ) ) ; +#10293 = FILL_AREA_STYLE_COLOUR ( '', #42548 ) ; +#10294 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10295 = MANIFOLD_SOLID_BREP ( 'ÊäÈë141', #95754 ) ; +#10296 = STYLED_ITEM ( 'NONE', ( #9215 ), #9639 ) ; +#10297 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10298 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99749 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #703, #46658, #39515 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10299 = LINE ( 'NONE', #79348, #48344 ) ; +#10300 = FILL_AREA_STYLE ('',( #50249 ) ) ; +#10302 = FILL_AREA_STYLE_COLOUR ( '', #63762 ) ; +#10301 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10303 = SURFACE_STYLE_USAGE ( .BOTH. , #80878 ) ; +#10305 = ADVANCED_FACE ( 'NONE', ( #83568 ), #39990, .T. ) ; +#10304 = FILL_AREA_STYLE ('',( #72190 ) ) ; +#10306 = FACE_OUTER_BOUND ( 'NONE', #33749, .T. ) ; +#10307 = CARTESIAN_POINT ( 'NONE', ( 1.098582290651209936, -0.9005718509792439708, 0.8100000000000000533 ) ) ; +#10308 = ORIENTED_EDGE ( 'NONE', *, *, #3415, .T. ) ; +#10309 = FILL_AREA_STYLE_COLOUR ( '', #87073 ) ; +#10310 = VECTOR ( 'NONE', #48736, 1000.000000000000000 ) ; +#10311 = FILL_AREA_STYLE_COLOUR ( '', #30815 ) ; +#10312 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, 1.600000000000000089, -11.32000000000000028 ) ) ; +#10313 = PRESENTATION_STYLE_ASSIGNMENT (( #71183 ) ) ; +#10314 = ORIENTED_EDGE ( 'NONE', *, *, #60928, .T. ) ; +#10315 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10316 = STYLED_ITEM ( 'NONE', ( #48603 ), #71252 ) ; +#10317 = LINE ( 'NONE', #56915, #52601 ) ; +#10318 = FILL_AREA_STYLE_COLOUR ( '', #61890 ) ; +#10319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10320 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56068 ), #88693 ) ; +#10322 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10323 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10324 = EDGE_CURVE ( 'NONE', #70633, #21155, #100693, .T. ) ; +#10325 = ORIENTED_EDGE ( 'NONE', *, *, #56826, .T. ) ; +#10326 = PRESENTATION_STYLE_ASSIGNMENT (( #25764 ) ) ; +#10327 = FACE_OUTER_BOUND ( 'NONE', #12754, .T. ) ; +#10328 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -13.54999999999999893 ) ) ; +#10329 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#10330 = STYLED_ITEM ( 'NONE', ( #91527 ), #88413 ) ; +#10331 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#10332 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10333 = VECTOR ( 'NONE', #90456, 1000.000000000000000 ) ; +#10334 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#10335 = PLANE ( 'NONE', #35381 ) ; +#10336 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37918, 'distance_accuracy_value', 'NONE'); +#10338 = PRESENTATION_STYLE_ASSIGNMENT (( #4284 ) ) ; +#10339 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#10340 = VECTOR ( 'NONE', #8050, 1000.000000000000000 ) ; +#10341 = FACE_OUTER_BOUND ( 'NONE', #61512, .T. ) ; +#10342 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #29861, #68335 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #14575 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#10343 = ORIENTED_EDGE ( 'NONE', *, *, #46439, .T. ) ; +#10344 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#10345 = ORIENTED_EDGE ( 'NONE', *, *, #40203, .F. ) ; +#10346 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50051, 'distance_accuracy_value', 'NONE'); +#10347 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2417, 'distance_accuracy_value', 'NONE'); +#10348 = ADVANCED_FACE ( 'NONE', ( #64488 ), #56361, .T. ) ; +#10349 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#10350 = CARTESIAN_POINT ( 'NONE', ( 0.1662790904141970283, -1.409021472795120022, 0.8299999999999999600 ) ) ; +#10351 = CARTESIAN_POINT ( 'NONE', ( 1.870562122921110015, -1.007076035477679987, 0.8100000000000000533 ) ) ; +#10352 = DIRECTION ( 'NONE', ( 2.356961244533699997E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#10353 = VECTOR ( 'NONE', #32422, 1000.000000000000114 ) ; +#10354 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10355 = ORIENTED_EDGE ( 'NONE', *, *, #10696, .T. ) ; +#10356 = CARTESIAN_POINT ( 'NONE', ( 7.895182750000000027, 10.29465675000000147, 0.8991599999999999593 ) ) ; +#10357 = SURFACE_STYLE_FILL_AREA ( #71229 ) ; +#10358 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78564, 'distance_accuracy_value', 'NONE'); +#10360 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46346 ) ) ; +#10359 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10361 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10362 = ORIENTED_EDGE ( 'NONE', *, *, #38880, .F. ) ; +#10363 = ADVANCED_FACE ( 'NONE', ( #87455 ), #33353, .T. ) ; +#10364 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30038 ) ) ; +#10365 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10366 = EDGE_LOOP ( 'NONE', ( #45843, #70785, #59862, #59084 ) ) ; +#10367 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10368 = VECTOR ( 'NONE', #45849, 1000.000000000000000 ) ; +#10369 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#10370 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20586, 'distance_accuracy_value', 'NONE'); +#10371 = STYLED_ITEM ( 'NONE', ( #60896 ), #12077 ) ; +#10372 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87917 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90350, #12164, #82702 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10373 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#10374 = ORIENTED_EDGE ( 'NONE', *, *, #20316, .T. ) ; +#10375 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10376 = PLANE ( 'NONE', #16870 ) ; +#10377 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10378 = SURFACE_STYLE_USAGE ( .BOTH. , #50338 ) ; +#10379 = LINE ( 'NONE', #78917, #29224 ) ; +#10380 = FILL_AREA_STYLE ('',( #80447 ) ) ; +#10381 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10382 = EDGE_CURVE ( 'NONE', #41651, #22324, #64306, .T. ) ; +#10383 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60692 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11069, #80131, #94882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10384 = ORIENTED_EDGE ( 'NONE', *, *, #39330, .F. ) ; +#10386 = ORIENTED_EDGE ( 'NONE', *, *, #65400, .F. ) ; +#10385 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10387 = SURFACE_STYLE_USAGE ( .BOTH. , #64128 ) ; +#10388 = SURFACE_STYLE_USAGE ( .BOTH. , #57489 ) ; +#10389 = ADVANCED_FACE ( 'NONE', ( #34869 ), #56850, .F. ) ; +#10390 = VERTEX_POINT ( 'NONE', #98540 ) ; +#10391 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10392 = SURFACE_SIDE_STYLE ('',( #48822 ) ) ; +#10393 = VECTOR ( 'NONE', #61800, 1000.000000000000000 ) ; +#10394 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75652 ) ) ; +#10395 = ORIENTED_EDGE ( 'NONE', *, *, #60076, .T. ) ; +#10397 = PRESENTATION_STYLE_ASSIGNMENT (( #58021 ) ) ; +#10396 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#10398 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69112 ), #70928 ) ; +#10399 = ORIENTED_EDGE ( 'NONE', *, *, #3099, .T. ) ; +#10400 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23491 ) ) ; +#10401 = ORIENTED_EDGE ( 'NONE', *, *, #9682, .T. ) ; +#10402 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#10403 = ORIENTED_EDGE ( 'NONE', *, *, #44858, .T. ) ; +#10404 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22213 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5463, #84122, #38172 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10405 = LINE ( 'NONE', #89637, #78402 ) ; +#10406 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28455 ) ) ; +#10407 = ORIENTED_EDGE ( 'NONE', *, *, #59922, .T. ) ; +#10408 = CARTESIAN_POINT ( 'NONE', ( 1.325329304031209965, -1.416724300735810127, 0.8299999999999999600 ) ) ; +#10409 = ORIENTED_EDGE ( 'NONE', *, *, #87724, .F. ) ; +#10410 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3959 ) ) ; +#10411 = SURFACE_STYLE_FILL_AREA ( #33005 ) ; +#10412 = CARTESIAN_POINT ( 'NONE', ( -1.036585239840499995, -1.260670644472420054, 0.8100000000000000533 ) ) ; +#10413 = PLANE ( 'NONE', #48145 ) ; +#10415 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10414 = AXIS2_PLACEMENT_3D ( 'NONE', #21664, #61502, #69081 ) ; +#10416 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#10417 = AXIS2_PLACEMENT_3D ( 'NONE', #21454, #52626, #58427 ) ; +#10418 = FILL_AREA_STYLE_COLOUR ( '', #85369 ) ; +#10419 = LINE ( 'NONE', #96272, #65414 ) ; +#10420 = PLANE ( 'NONE', #91038 ) ; +#10421 = CARTESIAN_POINT ( 'NONE', ( 1.286377402956589977, -0.9766832120545909657, 0.8299999999999999600 ) ) ; +#10422 = VERTEX_POINT ( 'NONE', #45464 ) ; +#10423 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10424 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 1.300000000000000266, 1.747825839084982648E-76 ) ) ; +#10426 = SURFACE_STYLE_FILL_AREA ( #24380 ) ; +#10425 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#10427 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38237 ) ) ; +#10428 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#10429 = SURFACE_STYLE_FILL_AREA ( #49349 ) ; +#10430 = LINE ( 'NONE', #72840, #37063 ) ; +#10431 = SURFACE_STYLE_USAGE ( .BOTH. , #64175 ) ; +#10432 = CARTESIAN_POINT ( 'NONE', ( 1.982710822981270216, 1.442163882139186004, -11.39687391007933925 ) ) ; +#10433 = EDGE_CURVE ( 'NONE', #1722, #48138, #83326, .T. ) ; +#10434 = ORIENTED_EDGE ( 'NONE', *, *, #50011, .F. ) ; +#10435 = PLANE ( 'NONE', #63520 ) ; +#10436 = ADVANCED_FACE ( 'NONE', ( #28684 ), #21521, .T. ) ; +#10437 = SURFACE_STYLE_USAGE ( .BOTH. , #2907 ) ; +#10438 = SURFACE_STYLE_USAGE ( .BOTH. , #80518 ) ; +#10439 = AXIS2_PLACEMENT_3D ( 'NONE', #51578, #59754, #29066 ) ; +#10440 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10441 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75569, 'distance_accuracy_value', 'NONE'); +#10442 = VECTOR ( 'NONE', #2236, 1000.000000000000114 ) ; +#10443 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10444 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10445 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10446 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220779480, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#10447 = FACE_OUTER_BOUND ( 'NONE', #18904, .T. ) ; +#10448 = DIRECTION ( 'NONE', ( 0.7974221540510216810, -0.6034218327411003946, 0.000000000000000000 ) ) ; +#10449 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10450 = MANIFOLD_SOLID_BREP ( 'ÊäÈë98', #68064 ) ; +#10451 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000001235, -0.1350000000000000089 ) ) ; +#10453 = EDGE_CURVE ( 'NONE', #11537, #36327, #65573, .T. ) ; +#10452 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#10454 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.2000000000000000111, -12.24500000000000099 ) ) ; +#10455 = CARTESIAN_POINT ( 'NONE', ( -0.1903619263518360194, -0.9137302873894740385, 0.8300000000000009592 ) ) ; +#10456 = FILL_AREA_STYLE_COLOUR ( '', #35792 ) ; +#10457 = ORIENTED_EDGE ( 'NONE', *, *, #11231, .F. ) ; +#10458 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#10459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81687, 'distance_accuracy_value', 'NONE'); +#10460 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59533 ) ) ; +#10462 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8648700000000000276 ) ) ; +#10461 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10463 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29590, 'distance_accuracy_value', 'NONE'); +#10464 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#10466 = VECTOR ( 'NONE', #27556, 1000.000000000000000 ) ; +#10465 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74145 ), #18645 ) ; +#10468 = ADVANCED_FACE ( 'NONE', ( #68476 ), #75170, .T. ) ; +#10469 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10470 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#10471 = STYLED_ITEM ( 'NONE', ( #5413 ), #77027 ) ; +#10472 = ORIENTED_EDGE ( 'NONE', *, *, #100083, .T. ) ; +#10473 = FILL_AREA_STYLE ('',( #9983 ) ) ; +#10474 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8648700000000000276 ) ) ; +#10475 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10476 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11867, 'distance_accuracy_value', 'NONE'); +#10477 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#10478 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26934 ) ) ; +#10479 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82259, 'distance_accuracy_value', 'NONE'); +#10480 = STYLED_ITEM ( 'NONE', ( #47995 ), #22113 ) ; +#10481 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#10482 = EDGE_LOOP ( 'NONE', ( #71420, #58819, #20828, #25189 ) ) ; +#10483 = ORIENTED_EDGE ( 'NONE', *, *, #59062, .T. ) ; +#10485 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10484 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10486 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64396 ) ) ; +#10487 = ORIENTED_EDGE ( 'NONE', *, *, #14939, .F. ) ; +#10488 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10489 = EDGE_CURVE ( 'NONE', #83136, #1836, #27745, .T. ) ; +#10490 = FILL_AREA_STYLE_COLOUR ( '', #2605 ) ; +#10491 = SURFACE_STYLE_FILL_AREA ( #18222 ) ; +#10492 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#10493 = PRESENTATION_STYLE_ASSIGNMENT (( #63250 ) ) ; +#10494 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #54757 ) ; +#10495 = SURFACE_SIDE_STYLE ('',( #79055 ) ) ; +#10496 = ADVANCED_FACE ( 'NONE', ( #8125 ), #54185, .F. ) ; +#10497 = SURFACE_SIDE_STYLE ('',( #63751 ) ) ; +#10499 = ORIENTED_EDGE ( 'NONE', *, *, #60928, .F. ) ; +#10498 = VERTEX_POINT ( 'NONE', #86325 ) ; +#10500 = AXIS2_PLACEMENT_3D ( 'NONE', #27856, #28335, #63522 ) ; +#10501 = VERTEX_POINT ( 'NONE', #79182 ) ; +#10502 = FILL_AREA_STYLE ('',( #66248 ) ) ; +#10503 = SURFACE_SIDE_STYLE ('',( #3473 ) ) ; +#10505 = CARTESIAN_POINT ( 'NONE', ( 1.400599642212259965, -0.9920916311794309994, 0.8100000000000010525 ) ) ; +#10504 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8299999999999999600 ) ) ; +#10506 = ORIENTED_EDGE ( 'NONE', *, *, #98425, .F. ) ; +#10507 = EDGE_CURVE ( 'NONE', #96986, #75309, #48939, .T. ) ; +#10508 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88821, #89816, #18849, #64835 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#10509 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10510 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2469 ), #36723 ) ; +#10511 = VERTEX_POINT ( 'NONE', #92451 ) ; +#10512 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10513 = ORIENTED_EDGE ( 'NONE', *, *, #66621, .T. ) ; +#10514 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8626, #39870, #24598, #2087 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#10515 = VECTOR ( 'NONE', #88881, 1000.000000000000000 ) ; +#10517 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10516 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#10518 = ORIENTED_EDGE ( 'NONE', *, *, #90435, .F. ) ; +#10519 = ORIENTED_EDGE ( 'NONE', *, *, #95123, .F. ) ; +#10520 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#10522 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10521 = SURFACE_STYLE_USAGE ( .BOTH. , #80599 ) ; +#10523 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67455 ), #13843 ) ; +#10525 = VERTEX_POINT ( 'NONE', #22526 ) ; +#10524 = FILL_AREA_STYLE_COLOUR ( '', #95050 ) ; +#10526 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#10527 = ORIENTED_EDGE ( 'NONE', *, *, #98920, .F. ) ; +#10528 = CARTESIAN_POINT ( 'NONE', ( -0.1903619263518360194, -0.9137302873894740385, 0.8100000000000000533 ) ) ; +#10529 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10530 = STYLED_ITEM ( 'NONE', ( #78976 ), #54214 ) ; +#10531 = VERTEX_POINT ( 'NONE', #69471 ) ; +#10533 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10534 = CARTESIAN_POINT ( 'NONE', ( 0.08699603081118000014, -1.280379325981960026, 0.8299999999999999600 ) ) ; +#10535 = ORIENTED_EDGE ( 'NONE', *, *, #14490, .T. ) ; +#10536 = ORIENTED_EDGE ( 'NONE', *, *, #63251, .T. ) ; +#10537 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.8999999999999990230, 0.1829999999999830096 ) ) ; +#10538 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#10539 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10540 = VECTOR ( 'NONE', #98435, 1000.000000000000000 ) ; +#10541 = CARTESIAN_POINT ( 'NONE', ( -1.203269655142430672, -1.140782136996280283, 0.8099999999998845901 ) ) ; +#10542 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14420 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9291, #17013, #85967 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10543 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68203, #23283, #92672 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10544 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10546 = EDGE_CURVE ( 'NONE', #54748, #81228, #53681, .T. ) ; +#10545 = FILL_AREA_STYLE_COLOUR ( '', #96652 ) ; +#10547 = EDGE_CURVE ( 'NONE', #61861, #74915, #22908, .T. ) ; +#10548 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #62052, #71702 ), + ( #40060, #85496 ), + ( #64054, #7805 ), + ( #46682, #54896 ), + ( #86002, #8312 ), + ( #4268, #56918 ), + ( #88031, #34437 ), + ( #81409, #11334 ), + ( #50768, #26768 ), + ( #41082, #81895 ), + ( #18569, #90023 ), + ( #11830, #65531 ), + ( #66057, #96662 ), + ( #33930, #73712 ), + ( #82394, #57935 ), + ( #64548, #26267 ), + ( #19583, #18043 ), + ( #42581, #3765 ), + ( #34934, #2769 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07262420069925870636, 0.1409697380364549890, 0.2055366295679730004, 0.2676612739694340104, 0.3281077529712519980, 0.3860824970032359915, 0.4440362253586950247, 0.5028572737747709631, 0.5616398490097329610, 0.6205525397731670445, 0.6796569225256300362, 0.7396960970132969715, 0.8012890424661629485, 0.8652792752259249598, 0.9314409141162129924, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#10549 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766239728, 0.6899999999999999467, 1.149590761170686535E-18 ) ) ; +#10550 = SURFACE_STYLE_FILL_AREA ( #11572 ) ; +#10551 = VERTEX_POINT ( 'NONE', #45968 ) ; +#10552 = AXIS2_PLACEMENT_3D ( 'NONE', #20400, #21408, #89356 ) ; +#10553 = ORIENTED_EDGE ( 'NONE', *, *, #39940, .T. ) ; +#10554 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10555 = LINE ( 'NONE', #66300, #56295 ) ; +#10556 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#10557 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#10558 = EDGE_CURVE ( 'NONE', #92443, #70633, #15332, .T. ) ; +#10559 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77556 ), #41655 ) ; +#10560 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10561 = LINE ( 'NONE', #57164, #59771 ) ; +#10562 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#10563 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10564 = EDGE_CURVE ( 'NONE', #99555, #14484, #34251, .T. ) ; +#10565 = EDGE_CURVE ( 'NONE', #30183, #71777, #48560, .T. ) ; +#10567 = VECTOR ( 'NONE', #58298, 1000.000000000000000 ) ; +#10566 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72605 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32748, #24090, #63410 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10568 = FILL_AREA_STYLE ('',( #27019 ) ) ; +#10569 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89308 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79776, #80785, #57304 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10570 = CARTESIAN_POINT ( 'NONE', ( -1.293097912083150058, -1.043393888298179917, 0.8299999999999998490 ) ) ; +#10571 = PRESENTATION_STYLE_ASSIGNMENT (( #9082 ) ) ; +#10572 = PLANE ( 'NONE', #80589 ) ; +#10573 = EDGE_CURVE ( 'NONE', #74680, #54018, #94966, .T. ) ; +#10574 = DIRECTION ( 'NONE', ( 0.7071067811865444641, 0.7071067811865505703, 0.000000000000000000 ) ) ; +#10575 = AXIS2_PLACEMENT_3D ( 'NONE', #30842, #54347, #85470 ) ; +#10576 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.1000000000000000056, -13.35000000000000142 ) ) ; +#10577 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10578 = SURFACE_SIDE_STYLE ('',( #89789 ) ) ; +#10579 = PRESENTATION_STYLE_ASSIGNMENT (( #73982 ) ) ; +#10581 = EDGE_CURVE ( 'NONE', #79295, #68118, #54563, .T. ) ; +#10580 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10582 = SURFACE_STYLE_FILL_AREA ( #50533 ) ; +#10583 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80560, 'distance_accuracy_value', 'NONE'); +#10584 = VERTEX_POINT ( 'NONE', #18375 ) ; +#10585 = CARTESIAN_POINT ( 'NONE', ( 1.549517223800989996, -0.9663557550577259736, 0.8299999999999999600 ) ) ; +#10586 = SURFACE_STYLE_USAGE ( .BOTH. , #96936 ) ; +#10587 = ORIENTED_EDGE ( 'NONE', *, *, #21130, .T. ) ; +#10588 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#10589 = PRESENTATION_STYLE_ASSIGNMENT (( #41847 ) ) ; +#10590 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10591 = EDGE_CURVE ( 'NONE', #73740, #69473, #17374, .T. ) ; +#10592 = CARTESIAN_POINT ( 'NONE', ( -0.1450077104042191978, -1.164919038798186257, 0.8233333333333333615 ) ) ; +#10593 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31822 ) ) ; +#10594 = FACE_OUTER_BOUND ( 'NONE', #26672, .T. ) ; +#10595 = AXIS2_PLACEMENT_3D ( 'NONE', #98950, #60280, #92835 ) ; +#10596 = LINE ( 'NONE', #87804, #22021 ) ; +#10597 = ADVANCED_FACE ( 'NONE', ( #27090 ), #18883, .T. ) ; +#10598 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10599 = EDGE_LOOP ( 'NONE', ( #82457, #95749, #94324, #42908 ) ) ; +#10600 = EDGE_CURVE ( 'NONE', #6033, #97325, #76824, .T. ) ; +#10601 = ORIENTED_EDGE ( 'NONE', *, *, #29415, .T. ) ; +#10602 = LINE ( 'NONE', #27053, #69903 ) ; +#10603 = FILL_AREA_STYLE ('',( #79147 ) ) ; +#10604 = FILL_AREA_STYLE ('',( #49525 ) ) ; +#10605 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#10606 = SURFACE_STYLE_USAGE ( .BOTH. , #73511 ) ; +#10607 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8099999999999619726 ) ) ; +#10609 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10608 = STYLED_ITEM ( 'NONE', ( #60640 ), #83317 ) ; +#10610 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88997 ) ) ; +#10611 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.01000000000000000021, -1.250000000000000000 ) ) ; +#10612 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10613 = VERTEX_POINT ( 'NONE', #41401 ) ; +#10614 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #29487 ) ) ; +#10615 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#10616 = ORIENTED_EDGE ( 'NONE', *, *, #80570, .F. ) ; +#10617 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10618 = LINE ( 'NONE', #41876, #85952 ) ; +#10619 = VERTEX_POINT ( 'NONE', #10639 ) ; +#10620 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#10621 = VECTOR ( 'NONE', #50484, 1000.000000000000000 ) ; +#10622 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10623 = LINE ( 'NONE', #79687, #79544 ) ; +#10624 = SURFACE_SIDE_STYLE ('',( #86825 ) ) ; +#10625 = CARTESIAN_POINT ( 'NONE', ( -1.019254590033279895, -1.033922635360990050, 0.8299999999999999600 ) ) ; +#10626 = DIRECTION ( 'NONE', ( 0.7071067811865470176, -0.7071067811865480168, 0.000000000000000000 ) ) ; +#10627 = SURFACE_STYLE_USAGE ( .BOTH. , #48551 ) ; +#10628 = EDGE_CURVE ( 'NONE', #15330, #63125, #42401, .T. ) ; +#10629 = STYLED_ITEM ( 'NONE', ( #16731 ), #77681 ) ; +#10630 = PRESENTATION_STYLE_ASSIGNMENT (( #49555 ) ) ; +#10632 = EDGE_LOOP ( 'NONE', ( #88350, #86706, #63342, #22517 ) ) ; +#10631 = ORIENTED_EDGE ( 'NONE', *, *, #93644, .T. ) ; +#10633 = MANIFOLD_SOLID_BREP ( 'ÊäÈë80', #23956 ) ; +#10634 = PRESENTATION_STYLE_ASSIGNMENT (( #11145 ) ) ; +#10635 = SURFACE_SIDE_STYLE ('',( #56730 ) ) ; +#10636 = ORIENTED_EDGE ( 'NONE', *, *, #38186, .T. ) ; +#10637 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#10638 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27089 ), #77560 ) ; +#10640 = PLANE ( 'NONE', #38170 ) ; +#10639 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, 3.500000000000000444, 0.000000000000000000 ) ) ; +#10641 = ORIENTED_EDGE ( 'NONE', *, *, #90722, .F. ) ; +#10642 = EDGE_CURVE ( 'NONE', #80241, #2083, #73540, .T. ) ; +#10643 = EDGE_LOOP ( 'NONE', ( #92947, #3591, #33662, #26073 ) ) ; +#10645 = VECTOR ( 'NONE', #68747, 1000.000000000000114 ) ; +#10644 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#10646 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13963 ) ) ; +#10647 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#10648 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10650 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#10649 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5833333333333333703, 0.000000000000000000 ) ) ; +#10651 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.383333333333326642, 0.000000000000000000 ) ) ; +#10652 = ORIENTED_EDGE ( 'NONE', *, *, #12797, .F. ) ; +#10653 = EDGE_CURVE ( 'NONE', #28686, #4944, #35760, .T. ) ; +#10654 = VERTEX_POINT ( 'NONE', #91839 ) ; +#10655 = FACE_OUTER_BOUND ( 'NONE', #50572, .T. ) ; +#10656 = STYLED_ITEM ( 'NONE', ( #12199 ), #4754 ) ; +#10657 = VERTEX_POINT ( 'NONE', #66374 ) ; +#10658 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10659 = VECTOR ( 'NONE', #76041, 1000.000000000000000 ) ; +#10660 = ADVANCED_FACE ( 'NONE', ( #28085 ), #75052, .F. ) ; +#10661 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51539 ) ) ; +#10663 = EDGE_LOOP ( 'NONE', ( #34820, #32932, #14688, #44152 ) ) ; +#10662 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10664 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98705 ), #41822 ) ; +#10665 = FILL_AREA_STYLE_COLOUR ( '', #16429 ) ; +#10666 = FILL_AREA_STYLE_COLOUR ( '', #4183 ) ; +#10667 = ORIENTED_EDGE ( 'NONE', *, *, #94574, .T. ) ; +#10668 = PRESENTATION_STYLE_ASSIGNMENT (( #96996 ) ) ; +#10669 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#10670 = VERTEX_POINT ( 'NONE', #5050 ) ; +#10671 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#10672 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#10673 = CARTESIAN_POINT ( 'NONE', ( -1.078436373535740067, -1.243129529655299992, 0.8300000000000000711 ) ) ; +#10674 = EDGE_CURVE ( 'NONE', #299, #83788, #19904, .T. ) ; +#10675 = EDGE_CURVE ( 'NONE', #14967, #12805, #21403, .T. ) ; +#10676 = LINE ( 'NONE', #41931, #39475 ) ; +#10677 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10679 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.1000000000000016015, 6.729667010201685742E-79 ) ) ; +#10678 = SURFACE_SIDE_STYLE ('',( #50615 ) ) ; +#10680 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#10681 = ORIENTED_EDGE ( 'NONE', *, *, #29442, .F. ) ; +#10682 = CARTESIAN_POINT ( 'NONE', ( 1.631872624588970089, -1.500900992704750081, 0.8099999999999982769 ) ) ; +#10683 = CARTESIAN_POINT ( 'NONE', ( -1.015539310577060039, -0.9199924700473179895, 0.8300000000000000711 ) ) ; +#10684 = ORIENTED_EDGE ( 'NONE', *, *, #89320, .F. ) ; +#10685 = SURFACE_STYLE_FILL_AREA ( #27637 ) ; +#10686 = SURFACE_STYLE_USAGE ( .BOTH. , #97019 ) ; +#10687 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.699999999999999734, -0.02000000000000000042 ) ) ; +#10688 = STYLED_ITEM ( 'NONE', ( #64152 ), #83626 ) ; +#10689 = VECTOR ( 'NONE', #80683, 1000.000000000000000 ) ; +#10690 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97831 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97541, #51645, #65938 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10691 = SURFACE_STYLE_FILL_AREA ( #71056 ) ; +#10693 = SURFACE_STYLE_USAGE ( .BOTH. , #27644 ) ; +#10692 = CARTESIAN_POINT ( 'NONE', ( -0.001577975213432779387, -1.393473016231464134, 0.8099999999996578826 ) ) ; +#10694 = LINE ( 'NONE', #25143, #33995 ) ; +#10695 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10696 = EDGE_CURVE ( 'NONE', #65278, #57258, #43382, .T. ) ; +#10697 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92320 ), #38478 ) ; +#10698 = EDGE_CURVE ( 'NONE', #6445, #19901, #58743, .T. ) ; +#10699 = FILL_AREA_STYLE ('',( #49618 ) ) ; +#10700 = CYLINDRICAL_SURFACE ( 'NONE', #13164, 0.01000000000000002623 ) ; +#10701 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91063 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2072, #73523, #57732 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10702 = EDGE_CURVE ( 'NONE', #31352, #85194, #82211, .T. ) ; +#10703 = FILL_AREA_STYLE ('',( #97030 ) ) ; +#10704 = PLANE ( 'NONE', #74064 ) ; +#10705 = VERTEX_POINT ( 'NONE', #74551 ) ; +#10707 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10706 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45078 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15607, #76405, #100768 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10709 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#10708 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8099999999999796252 ) ) ; +#10710 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94836 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39800, #63321, #18814 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10711 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10712 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78826, 'distance_accuracy_value', 'NONE'); +#10713 = ORIENTED_EDGE ( 'NONE', *, *, #8601, .F. ) ; +#10714 = SURFACE_SIDE_STYLE ('',( #64436 ) ) ; +#10715 = LINE ( 'NONE', #41969, #37501 ) ; +#10716 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10718 = AXIS2_PLACEMENT_3D ( 'NONE', #80639, #18810, #9074 ) ; +#10717 = SURFACE_STYLE_USAGE ( .BOTH. , #4156 ) ; +#10719 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#10720 = EDGE_CURVE ( 'NONE', #27614, #14100, #59766, .T. ) ; +#10721 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84208 ) ) ; +#10722 = SURFACE_STYLE_FILL_AREA ( #17935 ) ; +#10723 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10724 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8199999999999999512 ) ) ; +#10725 = LINE ( 'NONE', #88935, #15360 ) ; +#10726 = AXIS2_PLACEMENT_3D ( 'NONE', #86160, #16193, #53533 ) ; +#10727 = AXIS2_PLACEMENT_3D ( 'NONE', #10910, #82965, #35518 ) ; +#10728 = ADVANCED_FACE ( 'NONE', ( #20908 ), #53064, .T. ) ; +#10729 = FILL_AREA_STYLE ('',( #50659 ) ) ; +#10730 = ORIENTED_EDGE ( 'NONE', *, *, #35912, .F. ) ; +#10731 = EDGE_CURVE ( 'NONE', #36372, #81966, #44738, .T. ) ; +#10732 = EDGE_LOOP ( 'NONE', ( #28762, #16617, #90529, #92262 ) ) ; +#10733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23897 ) ) ; +#10734 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58506, 'distance_accuracy_value', 'NONE'); +#10735 = SURFACE_STYLE_USAGE ( .BOTH. , #33320 ) ; +#10736 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10737 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10738 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -1.012211148232466841E-16, -0.8499999999999999778 ) ) ; +#10739 = PLANE ( 'NONE', #47264 ) ; +#10740 = SURFACE_STYLE_USAGE ( .BOTH. , #41489 ) ; +#10741 = ORIENTED_EDGE ( 'NONE', *, *, #24910, .T. ) ; +#10742 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#10743 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#10744 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#10745 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10746 = ORIENTED_EDGE ( 'NONE', *, *, #21072, .T. ) ; +#10747 = VERTEX_POINT ( 'NONE', #77032 ) ; +#10748 = VECTOR ( 'NONE', #14233, 1000.000000000000000 ) ; +#10749 = FILL_AREA_STYLE ('',( #49165 ) ) ; +#10750 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10751 = VECTOR ( 'NONE', #8676, 1000.000000000000000 ) ; +#10752 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460026, -1.445454545454550210, 0.8099999999998321876 ) ) ; +#10753 = EDGE_CURVE ( 'NONE', #40674, #15430, #63057, .T. ) ; +#10754 = ORIENTED_EDGE ( 'NONE', *, *, #60144, .F. ) ; +#10755 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10756 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10757 = VERTEX_POINT ( 'NONE', #423 ) ; +#10758 = FILL_AREA_STYLE ('',( #66982 ) ) ; +#10759 = AXIS2_PLACEMENT_3D ( 'NONE', #1904, #40211, #9475 ) ; +#10760 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54899 ) ) ; +#10761 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2120, 'distance_accuracy_value', 'NONE'); +#10762 = FILL_AREA_STYLE_COLOUR ( '', #1790 ) ; +#10763 = EDGE_CURVE ( 'NONE', #77784, #29579, #8000, .T. ) ; +#10764 = VERTEX_POINT ( 'NONE', #14703 ) ; +#10765 = STYLED_ITEM ( 'NONE', ( #90497 ), #83116 ) ; +#10766 = SURFACE_SIDE_STYLE ('',( #40515 ) ) ; +#10767 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10768 = CARTESIAN_POINT ( 'NONE', ( -0.4616949353561959901, -1.145331018069290163, 0.8299999999999999600 ) ) ; +#10769 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#10770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10771 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98811 ), #87608 ) ; +#10773 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10772 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.60762199999999922, 0.8648700000000000276 ) ) ; +#10774 = ORIENTED_EDGE ( 'NONE', *, *, #27849, .T. ) ; +#10775 = EDGE_CURVE ( 'NONE', #12856, #17391, #93814, .T. ) ; +#10777 = EDGE_LOOP ( 'NONE', ( #11433, #21013, #62374, #37369 ) ) ; +#10776 = ORIENTED_EDGE ( 'NONE', *, *, #38260, .T. ) ; +#10778 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.05000000000000000278, 0.08229670385730990245 ) ) ; +#10779 = EDGE_LOOP ( 'NONE', ( #44482, #83209, #59745, #28557 ) ) ; +#10780 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.216666666666666785, 0.000000000000000000 ) ) ; +#10781 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58212 ) ) ; +#10782 = EDGE_CURVE ( 'NONE', #46216, #99386, #36111, .T. ) ; +#10783 = ORIENTED_EDGE ( 'NONE', *, *, #4795, .F. ) ; +#10784 = EDGE_LOOP ( 'NONE', ( #4181, #46097, #7898, #90267 ) ) ; +#10785 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7480 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90072, #81455, #33979 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10786 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.299999999999999822, 2.243222336733894049E-79 ) ) ; +#10788 = SURFACE_STYLE_USAGE ( .BOTH. , #80341 ) ; +#10787 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.7000000000000018430, 0.1829999999999659677 ) ) ; +#10789 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10790 = VERTEX_POINT ( 'NONE', #8503 ) ; +#10792 = EDGE_CURVE ( 'NONE', #58869, #87086, #24000, .T. ) ; +#10791 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#10793 = CLOSED_SHELL ( 'NONE', ( #7467, #45604, #57674, #69890, #65190, #52381 ) ) ; +#10794 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10795 = ORIENTED_EDGE ( 'NONE', *, *, #74662, .T. ) ; +#10796 = SURFACE_SIDE_STYLE ('',( #83729 ) ) ; +#10797 = AXIS2_PLACEMENT_3D ( 'NONE', #22331, #18680, #24894 ) ; +#10798 = SURFACE_STYLE_FILL_AREA ( #18536 ) ; +#10799 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10800 = LINE ( 'NONE', #34401, #13716 ) ; +#10801 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#10802 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10803 = VECTOR ( 'NONE', #3445, 1000.000000000000000 ) ; +#10805 = EDGE_CURVE ( 'NONE', #63379, #97408, #38734, .T. ) ; +#10804 = LINE ( 'NONE', #58403, #73731 ) ; +#10806 = EDGE_CURVE ( 'NONE', #97167, #63516, #14195, .T. ) ; +#10807 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10808 = SURFACE_SIDE_STYLE ('',( #56399 ) ) ; +#10809 = SURFACE_SIDE_STYLE ('',( #18544 ) ) ; +#10810 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10811 = MANIFOLD_SOLID_BREP ( 'ÊäÈë129', #59899 ) ; +#10812 = EDGE_CURVE ( 'NONE', #40643, #4574, #61245, .T. ) ; +#10813 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999956, -0.02000000000002305142 ) ) ; +#10814 = ADVANCED_FACE ( 'NONE', ( #45848 ), #95855, .F. ) ; +#10815 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54946 ) ) ; +#10816 = FILL_AREA_STYLE_COLOUR ( '', #17717 ) ; +#10818 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10817 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#10819 = PRESENTATION_STYLE_ASSIGNMENT (( #89532 ) ) ; +#10820 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10821 = CARTESIAN_POINT ( 'NONE', ( 0.4933869866146600169, 0.5990590759311020808, 0.8299999999999999600 ) ) ; +#10822 = ADVANCED_FACE ( 'NONE', ( #71393 ), #68384, .F. ) ; +#10823 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#10824 = FILL_AREA_STYLE ('',( #34921 ) ) ; +#10825 = CARTESIAN_POINT ( 'NONE', ( 1.063743438223609949, -0.9165513359838141083, 0.8100000000000000533 ) ) ; +#10826 = ORIENTED_EDGE ( 'NONE', *, *, #50653, .F. ) ; +#10827 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10828 = CARTESIAN_POINT ( 'NONE', ( 0.01569390708528280165, 1.386225820966699995, 0.8299999999999999600 ) ) ; +#10829 = PLANE ( 'NONE', #72193 ) ; +#10830 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10831 = ORIENTED_EDGE ( 'NONE', *, *, #65471, .F. ) ; +#10832 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 2.134644999999999904, 0.8648700000000000276 ) ) ; +#10833 = VECTOR ( 'NONE', #47455, 1000.000000000000000 ) ; +#10834 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#10835 = LINE ( 'NONE', #8815, #55 ) ; +#10836 = CARTESIAN_POINT ( 'NONE', ( 1.581953864252920283, -1.079063990458370093, 0.8100000000000000533 ) ) ; +#10837 = LINE ( 'NONE', #58439, #51812 ) ; +#10838 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.000000000000000000 ) ) ; +#10839 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10840 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51413 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77462, #6459, #7444 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10841 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10842 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10843 = ORIENTED_EDGE ( 'NONE', *, *, #86538, .T. ) ; +#10844 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#10845 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46755 ) ) ; +#10846 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10848 = PRESENTATION_STYLE_ASSIGNMENT (( #90031 ) ) ; +#10849 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#10850 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#10851 = LINE ( 'NONE', #95668, #23654 ) ; +#10852 = LINE ( 'NONE', #42090, #68606 ) ; +#10853 = FILL_AREA_STYLE ('',( #33439 ) ) ; +#10854 = FILL_AREA_STYLE_COLOUR ( '', #90888 ) ; +#10855 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666653285, 1.100000000000000089, 0.000000000000000000 ) ) ; +#10856 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10857 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10858 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29102 ) ) ; +#10859 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 8.852159000000000333, 0.8648700000000000276 ) ) ; +#10860 = ORIENTED_EDGE ( 'NONE', *, *, #61663, .T. ) ; +#10861 = EDGE_CURVE ( 'NONE', #13051, #69898, #36635, .T. ) ; +#10862 = EDGE_LOOP ( 'NONE', ( #94624, #36955, #49683, #95821 ) ) ; +#10864 = VECTOR ( 'NONE', #19730, 1000.000000000000000 ) ; +#10863 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10865 = CARTESIAN_POINT ( 'NONE', ( -1.277612491286911567, -1.496445653724932434, 0.8099999999996225775 ) ) ; +#10866 = DIRECTION ( 'NONE', ( 0.7071067811865435759, -0.7071067811865514585, 0.000000000000000000 ) ) ; +#10867 = FILL_AREA_STYLE ('',( #57966 ) ) ; +#10869 = EDGE_CURVE ( 'NONE', #27347, #82492, #96205, .T. ) ; +#10868 = FILL_AREA_STYLE_COLOUR ( '', #96074 ) ; +#10870 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#10871 = CLOSED_SHELL ( 'NONE', ( #33153, #92225, #96743, #89963, #23492, #84679 ) ) ; +#10872 = VERTEX_POINT ( 'NONE', #97832 ) ; +#10873 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#10874 = VECTOR ( 'NONE', #15523, 1000.000000000000000 ) ; +#10875 = AXIS2_PLACEMENT_3D ( 'NONE', #94938, #50555, #65851 ) ; +#10876 = PRESENTATION_STYLE_ASSIGNMENT (( #56464 ) ) ; +#10877 = ORIENTED_EDGE ( 'NONE', *, *, #99872, .T. ) ; +#10878 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10879 = FILL_AREA_STYLE_COLOUR ( '', #36980 ) ; +#10880 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10881 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.000000000000000000 ) ) ; +#10882 = EDGE_CURVE ( 'NONE', #36766, #68615, #83589, .T. ) ; +#10883 = FACE_OUTER_BOUND ( 'NONE', #92350, .T. ) ; +#10884 = ORIENTED_EDGE ( 'NONE', *, *, #64473, .F. ) ; +#10885 = FACE_OUTER_BOUND ( 'NONE', #29342, .T. ) ; +#10886 = FILL_AREA_STYLE_COLOUR ( '', #38048 ) ; +#10887 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#10888 = LINE ( 'NONE', #42138, #40332 ) ; +#10889 = ADVANCED_FACE ( 'NONE', ( #5911 ), #35638, .T. ) ; +#10890 = ORIENTED_EDGE ( 'NONE', *, *, #47579, .F. ) ; +#10891 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#10892 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#10893 = AXIS2_PLACEMENT_3D ( 'NONE', #6850, #61603, #94050 ) ; +#10894 = CARTESIAN_POINT ( 'NONE', ( -1.344866921067736421, -1.144781931243857631, 0.8099999999998810374 ) ) ; +#10895 = VECTOR ( 'NONE', #10957, 1000.000000000000000 ) ; +#10896 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10897 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10898 = VECTOR ( 'NONE', #48865, 1000.000000000000000 ) ; +#10899 = EDGE_CURVE ( 'NONE', #95352, #93316, #11535, .T. ) ; +#10900 = VERTEX_POINT ( 'NONE', #50956 ) ; +#10902 = ORIENTED_EDGE ( 'NONE', *, *, #48473, .F. ) ; +#10901 = FACE_OUTER_BOUND ( 'NONE', #24873, .T. ) ; +#10903 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12518 ) ) ; +#10904 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#10905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66280, 'distance_accuracy_value', 'NONE'); +#10906 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10907 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#10908 = PRESENTATION_STYLE_ASSIGNMENT (( #12923 ) ) ; +#10909 = EDGE_CURVE ( 'NONE', #33631, #76033, #73915, .T. ) ; +#10910 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#10911 = VERTEX_POINT ( 'NONE', #35136 ) ; +#10912 = FILL_AREA_STYLE_COLOUR ( '', #97214 ) ; +#10913 = FILL_AREA_STYLE ('',( #67981 ) ) ; +#10914 = SURFACE_STYLE_FILL_AREA ( #80980 ) ; +#10915 = PRESENTATION_STYLE_ASSIGNMENT (( #79460 ) ) ; +#10916 = VERTEX_POINT ( 'NONE', #12036 ) ; +#10917 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77827 ) ) ; +#10919 = SURFACE_STYLE_FILL_AREA ( #96745 ) ; +#10918 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10920 = ORIENTED_EDGE ( 'NONE', *, *, #43528, .T. ) ; +#10921 = VERTEX_POINT ( 'NONE', #97356 ) ; +#10922 = CARTESIAN_POINT ( 'NONE', ( 1.033073635753643860, -1.167080940716315185, 0.8099999999998847011 ) ) ; +#10923 = EDGE_CURVE ( 'NONE', #40392, #73172, #27459, .T. ) ; +#10924 = EDGE_CURVE ( 'NONE', #59623, #21902, #19788, .T. ) ; +#10925 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8483 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54977, #39633, #826 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10926 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#10927 = SURFACE_STYLE_USAGE ( .BOTH. , #51845 ) ; +#10928 = AXIS2_PLACEMENT_3D ( 'NONE', #13885, #59947, #91543 ) ; +#10929 = STYLED_ITEM ( 'NONE', ( #31147 ), #62528 ) ; +#10930 = ORIENTED_EDGE ( 'NONE', *, *, #62785, .F. ) ; +#10931 = EDGE_CURVE ( 'NONE', #23933, #33366, #22285, .T. ) ; +#10932 = EDGE_CURVE ( 'NONE', #77789, #27802, #62134, .T. ) ; +#10933 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10934 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10935 = EDGE_LOOP ( 'NONE', ( #32732, #3528, #8682, #12170 ) ) ; +#10937 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55391 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43861, #84174, #4548 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#10936 = CARTESIAN_POINT ( 'NONE', ( 1.261158141153259971, -1.441583773770549914, 0.8100000000000000533 ) ) ; +#10938 = PLANE ( 'NONE', #80555 ) ; +#10939 = ORIENTED_EDGE ( 'NONE', *, *, #23412, .T. ) ; +#10940 = SURFACE_STYLE_USAGE ( .BOTH. , #79484 ) ; +#10941 = CLOSED_SHELL ( 'NONE', ( #65654, #14972, #96573, #11290, #15046, #7526 ) ) ; +#10942 = CYLINDRICAL_SURFACE ( 'NONE', #5289, 0.04999999999999969746 ) ; +#10943 = CARTESIAN_POINT ( 'NONE', ( -1.180619344033760010, -1.219266740403220028, 0.8100000000000000533 ) ) ; +#10944 = VECTOR ( 'NONE', #90410, 1000.000000000000000 ) ; +#10945 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#10946 = ADVANCED_FACE ( 'NONE', ( #92219 ), #84566, .T. ) ; +#10947 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63246 ), #58377 ) ; +#10948 = ADVANCED_FACE ( 'NONE', ( #39624 ), #47276, .T. ) ; +#10949 = CARTESIAN_POINT ( 'NONE', ( 1.296768031029680079, -0.9834456900322131601, 0.8299999999999999600 ) ) ; +#10950 = EDGE_LOOP ( 'NONE', ( #7001, #77256, #60824, #1966 ) ) ; +#10951 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8648700000000000276 ) ) ; +#10952 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10953 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#10954 = FILL_AREA_STYLE_COLOUR ( '', #54116 ) ; +#10955 = SURFACE_SIDE_STYLE ('',( #49869 ) ) ; +#10956 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77005, 'distance_accuracy_value', 'NONE'); +#10957 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#10958 = VECTOR ( 'NONE', #31540, 1000.000000000000000 ) ; +#10959 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#10960 = SURFACE_STYLE_FILL_AREA ( #88160 ) ; +#10961 = LINE ( 'NONE', #70814, #54920 ) ; +#10962 = LINE ( 'NONE', #9462, #47767 ) ; +#10963 = ORIENTED_EDGE ( 'NONE', *, *, #88991, .F. ) ; +#10964 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#10965 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10966 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10967 = LINE ( 'NONE', #42217, #6040 ) ; +#10968 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10969 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10970 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10971 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#10972 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10973 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10974 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988787, -3.383333333333326642, 0.000000000000000000 ) ) ; +#10975 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10976 = FACE_OUTER_BOUND ( 'NONE', #46860, .T. ) ; +#10977 = MANIFOLD_SOLID_BREP ( 'ÊäÈë7', #48585 ) ; +#10978 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#10979 = LINE ( 'NONE', #42232, #81612 ) ; +#10980 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58342 ) ) ; +#10981 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#10982 = CARTESIAN_POINT ( 'NONE', ( -0.2475423460550890131, -0.9531265814360270205, 0.8300000000000009592 ) ) ; +#10983 = ADVANCED_FACE ( 'NONE', ( #94725 ), #55482, .T. ) ; +#10984 = LINE ( 'NONE', #2924, #86779 ) ; +#10985 = ORIENTED_EDGE ( 'NONE', *, *, #56764, .T. ) ; +#10987 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59943 ) ) ; +#10986 = SURFACE_STYLE_FILL_AREA ( #26414 ) ; +#10988 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#10989 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#10990 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#10991 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#10992 = PLANE ( 'NONE', #75414 ) ; +#10994 = VERTEX_POINT ( 'NONE', #88115 ) ; +#10993 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71439 ), #99026 ) ; +#10995 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4513 ), #100586 ) ; +#10996 = DIRECTION ( 'NONE', ( 0.7071090539100497452, -0.7071045084557405769, 0.000000000000000000 ) ) ; +#10997 = FACE_OUTER_BOUND ( 'NONE', #67565, .T. ) ; +#10998 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#10999 = FACE_OUTER_BOUND ( 'NONE', #53545, .T. ) ; +#11000 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11001 = SURFACE_SIDE_STYLE ('',( #57088 ) ) ; +#11002 = VECTOR ( 'NONE', #74896, 1000.000000000000000 ) ; +#11003 = STYLED_ITEM ( 'NONE', ( #45748 ), #60 ) ; +#11004 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11005 = EDGE_CURVE ( 'NONE', #71556, #41785, #41656, .T. ) ; +#11006 = VERTEX_POINT ( 'NONE', #65119 ) ; +#11007 = VERTEX_POINT ( 'NONE', #63636 ) ; +#11008 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#11009 = ORIENTED_EDGE ( 'NONE', *, *, #20107, .F. ) ; +#11010 = CARTESIAN_POINT ( 'NONE', ( 1.759379393379719936, -1.230342595016630014, 0.8100000000000000533 ) ) ; +#11011 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11012 = FILL_AREA_STYLE ('',( #74403 ) ) ; +#11013 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11014 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11015 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11016 = SURFACE_SIDE_STYLE ('',( #2958 ) ) ; +#11017 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5245 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57021, #87128, #42189 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11019 = ORIENTED_EDGE ( 'NONE', *, *, #96975, .T. ) ; +#11018 = VERTEX_POINT ( 'NONE', #34005 ) ; +#11020 = ORIENTED_EDGE ( 'NONE', *, *, #9251, .T. ) ; +#11021 = AXIS2_PLACEMENT_3D ( 'NONE', #6707, #59961, #38453 ) ; +#11022 = ORIENTED_EDGE ( 'NONE', *, *, #77748, .F. ) ; +#11023 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56571, 'distance_accuracy_value', 'NONE'); +#11024 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#11026 = FACE_OUTER_BOUND ( 'NONE', #91570, .T. ) ; +#11025 = CARTESIAN_POINT ( 'NONE', ( 0.5450788742336990511, -1.052784384528720141, 0.8100000000000000533 ) ) ; +#11027 = ORIENTED_EDGE ( 'NONE', *, *, #98234, .T. ) ; +#11028 = ADVANCED_FACE ( 'NONE', ( #2348 ), #49305, .T. ) ; +#11029 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58480 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87996, #33901, #66518 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11030 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999409, 0.8648700000000000276 ) ) ; +#11031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11032 = ORIENTED_EDGE ( 'NONE', *, *, #28435, .F. ) ; +#11033 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11034 = STYLED_ITEM ( 'NONE', ( #86026 ), #32016 ) ; +#11036 = VERTEX_POINT ( 'NONE', #31970 ) ; +#11035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9445 ) ) ; +#11037 = SURFACE_STYLE_FILL_AREA ( #12561 ) ; +#11038 = ORIENTED_EDGE ( 'NONE', *, *, #52421, .T. ) ; +#11039 = ORIENTED_EDGE ( 'NONE', *, *, #84358, .T. ) ; +#11040 = SURFACE_STYLE_FILL_AREA ( #42293 ) ; +#11041 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69777 ), #56866 ) ; +#11043 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11042 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11044 = PLANE ( 'NONE', #81573 ) ; +#11046 = EDGE_LOOP ( 'NONE', ( #30979, #39539, #20904, #46518 ) ) ; +#11045 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.3666666666666656416, 0.000000000000000000 ) ) ; +#11047 = ADVANCED_FACE ( 'NONE', ( #63131 ), #94220, .T. ) ; +#11048 = ORIENTED_EDGE ( 'NONE', *, *, #21192, .T. ) ; +#11049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19748, #60097, #20742 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11050 = VECTOR ( 'NONE', #82897, 1000.000000000000000 ) ; +#11051 = CARTESIAN_POINT ( 'NONE', ( -0.2066711868101530070, -0.9216047924506359790, 0.8299999999999999600 ) ) ; +#11052 = LINE ( 'NONE', #19293, #80033 ) ; +#11053 = VERTEX_POINT ( 'NONE', #97715 ) ; +#11055 = SURFACE_STYLE_FILL_AREA ( #81118 ) ; +#11054 = SURFACE_STYLE_USAGE ( .BOTH. , #25481 ) ; +#11056 = ORIENTED_EDGE ( 'NONE', *, *, #87636, .T. ) ; +#11057 = VERTEX_POINT ( 'NONE', #20148 ) ; +#11058 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#11059 = AXIS2_PLACEMENT_3D ( 'NONE', #32566, #79016, #9492 ) ; +#11060 = FILL_AREA_STYLE_COLOUR ( '', #84935 ) ; +#11061 = SURFACE_STYLE_FILL_AREA ( #57668 ) ; +#11062 = SURFACE_SIDE_STYLE ('',( #97392 ) ) ; +#11063 = EDGE_CURVE ( 'NONE', #14320, #81145, #83460, .T. ) ; +#11065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7566, 'distance_accuracy_value', 'NONE'); +#11066 = ORIENTED_EDGE ( 'NONE', *, *, #8582, .F. ) ; +#11067 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82509 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74618, #28642, #98990 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11068 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67356 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66683, #19733, #74368 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11069 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11070 = ORIENTED_EDGE ( 'NONE', *, *, #46767, .F. ) ; +#11071 = VECTOR ( 'NONE', #46797, 1000.000000000000000 ) ; +#11072 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11073 = CARTESIAN_POINT ( 'NONE', ( 1.394831661730270067, -1.224577966852969935, 0.8299999999999999600 ) ) ; +#11074 = SURFACE_STYLE_USAGE ( .BOTH. , #4492 ) ; +#11075 = CARTESIAN_POINT ( 'NONE', ( 0.5238200612200860640, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#11076 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11077 = LINE ( 'NONE', #50007, #3066 ) ; +#11078 = SURFACE_STYLE_FILL_AREA ( #88283 ) ; +#11079 = VECTOR ( 'NONE', #77427, 1000.000000000000000 ) ; +#11080 = FACE_OUTER_BOUND ( 'NONE', #548, .T. ) ; +#11081 = VERTEX_POINT ( 'NONE', #73302 ) ; +#11082 = SURFACE_STYLE_FILL_AREA ( #10568 ) ; +#11083 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11084 = FILL_AREA_STYLE ('',( #26014 ) ) ; +#11085 = PRESENTATION_STYLE_ASSIGNMENT (( #33676 ) ) ; +#11086 = FILL_AREA_STYLE ('',( #25515 ) ) ; +#11087 = PRESENTATION_STYLE_ASSIGNMENT (( #73484 ) ) ; +#11088 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30749 ), #14395 ) ; +#11089 = PRESENTATION_STYLE_ASSIGNMENT (( #34193 ) ) ; +#11090 = AXIS2_PLACEMENT_3D ( 'NONE', #91184, #20735, #91668 ) ; +#11091 = ADVANCED_FACE ( 'NONE', ( #67598 ), #26845, .F. ) ; +#11092 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11093 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 2.567390744878445071E-16 ) ) ; +#11094 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#11095 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722699999999918, 0.8991599999999999593 ) ) ; +#11096 = LINE ( 'NONE', #42345, #48579 ) ; +#11097 = PLANE ( 'NONE', #69061 ) ; +#11098 = PLANE ( 'NONE', #27445 ) ; +#11099 = ORIENTED_EDGE ( 'NONE', *, *, #69304, .T. ) ; +#11100 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#11102 = ADVANCED_FACE ( 'NONE', ( #89114 ), #36512, .T. ) ; +#11101 = SURFACE_STYLE_FILL_AREA ( #97432 ) ; +#11103 = EDGE_LOOP ( 'NONE', ( #23413, #19488, #7645, #13895 ) ) ; +#11104 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11105 = FILL_AREA_STYLE_COLOUR ( '', #4007 ) ; +#11106 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#11107 = VECTOR ( 'NONE', #16232, 1000.000000000000114 ) ; +#11108 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#11109 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#11110 = ORIENTED_EDGE ( 'NONE', *, *, #35454, .T. ) ; +#11111 = ORIENTED_EDGE ( 'NONE', *, *, #7188, .T. ) ; +#11112 = FACE_OUTER_BOUND ( 'NONE', #50974, .T. ) ; +#11113 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25564, 'distance_accuracy_value', 'NONE'); +#11114 = SURFACE_STYLE_USAGE ( .BOTH. , #49524 ) ; +#11115 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62132 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86203, #94352, #430 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11116 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#11117 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11118 = VECTOR ( 'NONE', #30262, 1000.000000000000000 ) ; +#11119 = PLANE ( 'NONE', #83150 ) ; +#11120 = SURFACE_SIDE_STYLE ('',( #94937 ) ) ; +#11121 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11122 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #82675, #35550 ) ; +#11123 = PRESENTATION_STYLE_ASSIGNMENT (( #41370 ) ) ; +#11124 = SURFACE_SIDE_STYLE ('',( #25556 ) ) ; +#11125 = VECTOR ( 'NONE', #46861, 1000.000000000000000 ) ; +#11126 = ORIENTED_EDGE ( 'NONE', *, *, #47371, .T. ) ; +#11127 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#11128 = VECTOR ( 'NONE', #59309, 1000.000000000000000 ) ; +#11129 = ORIENTED_EDGE ( 'NONE', *, *, #46906, .F. ) ; +#11130 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11131 = PLANE ( 'NONE', #99415 ) ; +#11132 = EDGE_CURVE ( 'NONE', #53207, #26361, #100641, .T. ) ; +#11133 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11134 = SURFACE_STYLE_USAGE ( .BOTH. , #87827 ) ; +#11135 = LINE ( 'NONE', #58735, #95277 ) ; +#11136 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11137 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11138 = CARTESIAN_POINT ( 'NONE', ( 1.750822000000000100, 10.47343599999999952, 0.8991599999999999593 ) ) ; +#11139 = CARTESIAN_POINT ( 'NONE', ( -0.3919372300192849878, -0.9729160362892149694, 0.8100000000000000533 ) ) ; +#11141 = VECTOR ( 'NONE', #5378, 1000.000000000000227 ) ; +#11140 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8100000000000000533 ) ) ; +#11142 = VECTOR ( 'NONE', #24793, 1000.000000000000114 ) ; +#11144 = VERTEX_POINT ( 'NONE', #54322 ) ; +#11143 = ORIENTED_EDGE ( 'NONE', *, *, #75351, .F. ) ; +#11145 = SURFACE_STYLE_USAGE ( .BOTH. , #35259 ) ; +#11147 = STYLED_ITEM ( 'NONE', ( #24814 ), #42149 ) ; +#11146 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.1600000000000000033, -1.129999999999999893 ) ) ; +#11148 = ORIENTED_EDGE ( 'NONE', *, *, #88829, .T. ) ; +#11149 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11150 = VECTOR ( 'NONE', #8658, 1000.000000000000000 ) ; +#11151 = EDGE_LOOP ( 'NONE', ( #4187, #84164, #35787, #17220 ) ) ; +#11152 = EDGE_CURVE ( 'NONE', #12291, #35208, #54846, .T. ) ; +#11153 = VERTEX_POINT ( 'NONE', #69079 ) ; +#11154 = EDGE_CURVE ( 'NONE', #24251, #26194, #46640, .T. ) ; +#11155 = FILL_AREA_STYLE ('',( #56229 ) ) ; +#11156 = SURFACE_SIDE_STYLE ('',( #18380 ) ) ; +#11157 = SURFACE_STYLE_FILL_AREA ( #74041 ) ; +#11159 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11158 = CARTESIAN_POINT ( 'NONE', ( -0.1439069218330049915, -1.121518536532789989, 0.8139999999999999458 ) ) ; +#11160 = ORIENTED_EDGE ( 'NONE', *, *, #51716, .F. ) ; +#11161 = ORIENTED_EDGE ( 'NONE', *, *, #76198, .T. ) ; +#11162 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11163 = ORIENTED_EDGE ( 'NONE', *, *, #96355, .F. ) ; +#11164 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11165 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11166 = ORIENTED_EDGE ( 'NONE', *, *, #100449, .T. ) ; +#11167 = EDGE_CURVE ( 'NONE', #62472, #37111, #52821, .T. ) ; +#11168 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11169 = SURFACE_SIDE_STYLE ('',( #81740 ) ) ; +#11170 = ORIENTED_EDGE ( 'NONE', *, *, #67276, .T. ) ; +#11171 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#11172 = CARTESIAN_POINT ( 'NONE', ( -0.9902043555515913642, -1.357204004350457627, 0.8099999999997251621 ) ) ; +#11173 = ORIENTED_EDGE ( 'NONE', *, *, #9423, .T. ) ; +#11174 = SURFACE_STYLE_USAGE ( .BOTH. , #39511 ) ; +#11175 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69991 ), #22705 ) ; +#11177 = CARTESIAN_POINT ( 'NONE', ( -1.282612376779509900, -1.188596174736179956, 0.8300000000000000711 ) ) ; +#11178 = PLANE ( 'NONE', #57505 ) ; +#11179 = FILL_AREA_STYLE ('',( #66403 ) ) ; +#11180 = PRESENTATION_STYLE_ASSIGNMENT (( #4601 ) ) ; +#11181 = ADVANCED_FACE ( 'NONE', ( #83952 ), #62502, .T. ) ; +#11182 = VECTOR ( 'NONE', #33572, 1000.000000000000000 ) ; +#11183 = CARTESIAN_POINT ( 'NONE', ( 1.515867623847370282, -1.051115598670280038, 0.8299999999999997380 ) ) ; +#11184 = EDGE_LOOP ( 'NONE', ( #67846, #21524, #57619, #13703 ) ) ; +#11185 = CARTESIAN_POINT ( 'NONE', ( 1.536752279304230306, -1.444662699359980040, 0.8099999999999982769 ) ) ; +#11186 = CARTESIAN_POINT ( 'NONE', ( -0.9621292638465409608, -0.9747981717974689708, 0.8300000000000000711 ) ) ; +#11187 = VERTEX_POINT ( 'NONE', #37998 ) ; +#11188 = SURFACE_STYLE_FILL_AREA ( #97528 ) ; +#11189 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8648700000000000276 ) ) ; +#11190 = CARTESIAN_POINT ( 'NONE', ( -0.1557459988712610044, -1.504992180692799941, 0.8100000000000000533 ) ) ; +#11191 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27640 ), #21053 ) ; +#11192 = VECTOR ( 'NONE', #73746, 1000.000000000000114 ) ; +#11193 = CARTESIAN_POINT ( 'NONE', ( -0.5424062986694020427, -1.258396457361969922, 0.8300000000000000711 ) ) ; +#11194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11196 = FILL_AREA_STYLE_COLOUR ( '', #13561 ) ; +#11195 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55567 ) ) ; +#11198 = SURFACE_STYLE_FILL_AREA ( #40442 ) ; +#11199 = SURFACE_SIDE_STYLE ('',( #81768 ) ) ; +#11200 = STYLED_ITEM ( 'NONE', ( #94595 ), #56243 ) ; +#11201 = FACE_OUTER_BOUND ( 'NONE', #2088, .T. ) ; +#11202 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35817 ), #99239 ) ; +#11203 = FILL_AREA_STYLE_COLOUR ( '', #59058 ) ; +#11204 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8648700000000000276 ) ) ; +#11205 = VECTOR ( 'NONE', #55771, 1000.000000000000000 ) ; +#11206 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11207 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11208 = VERTEX_POINT ( 'NONE', #92582 ) ; +#11209 = EDGE_CURVE ( 'NONE', #1435, #17365, #77282, .T. ) ; +#11210 = CIRCLE ( 'NONE', #63514, 0.9754570600145798798 ) ; +#11212 = SURFACE_STYLE_USAGE ( .BOTH. , #65410 ) ; +#11211 = FILL_AREA_STYLE ('',( #3644 ) ) ; +#11213 = STYLED_ITEM ( 'NONE', ( #52494 ), #1568 ) ; +#11214 = FILL_AREA_STYLE ('',( #2649 ) ) ; +#11215 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53721 ) ) ; +#11216 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14539 ) ) ; +#11217 = ORIENTED_EDGE ( 'NONE', *, *, #11902, .T. ) ; +#11218 = ADVANCED_FACE ( 'NONE', ( #84944 ), #14957, .T. ) ; +#11219 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11220 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#11221 = CARTESIAN_POINT ( 'NONE', ( -1.031006683134279900, -1.010360997253880067, 0.8299999999999999600 ) ) ; +#11222 = DIRECTION ( 'NONE', ( -0.7071060119555119261, 0.7071075504167462222, 0.000000000000000000 ) ) ; +#11223 = LINE ( 'NONE', #61327, #56802 ) ; +#11224 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.35000000000000142 ) ) ; +#11225 = EDGE_CURVE ( 'NONE', #1299, #2903, #49196, .T. ) ; +#11226 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11227 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32610, 'distance_accuracy_value', 'NONE'); +#11228 = AXIS2_PLACEMENT_3D ( 'NONE', #6108, #29169, #21991 ) ; +#11229 = VERTEX_POINT ( 'NONE', #95102 ) ; +#11230 = FILL_AREA_STYLE_COLOUR ( '', #61271 ) ; +#11231 = EDGE_CURVE ( 'NONE', #25960, #8286, #94610, .T. ) ; +#11232 = ORIENTED_EDGE ( 'NONE', *, *, #77053, .T. ) ; +#11233 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11234 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7327, 'distance_accuracy_value', 'NONE'); +#11235 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21543, 'distance_accuracy_value', 'NONE'); +#11236 = STYLED_ITEM ( 'NONE', ( #56064 ), #44298 ) ; +#11237 = DIRECTION ( 'NONE', ( -1.445602896647339903E-15, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11238 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#11239 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#11240 = PRESENTATION_STYLE_ASSIGNMENT (( #34349 ) ) ; +#11241 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#11242 = ORIENTED_EDGE ( 'NONE', *, *, #74999, .F. ) ; +#11243 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#11244 = ORIENTED_EDGE ( 'NONE', *, *, #48394, .T. ) ; +#11245 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11246 = VECTOR ( 'NONE', #79922, 1000.000000000000000 ) ; +#11247 = LINE ( 'NONE', #18485, #77791 ) ; +#11248 = ORIENTED_EDGE ( 'NONE', *, *, #19673, .T. ) ; +#11249 = EDGE_CURVE ( 'NONE', #55363, #58097, #25238, .T. ) ; +#11250 = ADVANCED_FACE ( 'NONE', ( #2730 ), #33888, .T. ) ; +#11251 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11252 = VECTOR ( 'NONE', #21850, 1000.000000000000000 ) ; +#11253 = VECTOR ( 'NONE', #45116, 1000.000000000000114 ) ; +#11254 = AXIS2_PLACEMENT_3D ( 'NONE', #30778, #8570, #87282 ) ; +#11255 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#11256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11257 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11258 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11259 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11260 = ORIENTED_EDGE ( 'NONE', *, *, #56018, .T. ) ; +#11261 = FACE_OUTER_BOUND ( 'NONE', #54759, .T. ) ; +#11262 = VECTOR ( 'NONE', #52420, 1000.000000000000114 ) ; +#11264 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11263 = STYLED_ITEM ( 'NONE', ( #37954 ), #92042 ) ; +#11265 = ORIENTED_EDGE ( 'NONE', *, *, #45896, .F. ) ; +#11266 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11267 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50554 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71212, #58831, #1266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11268 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11269 = ORIENTED_EDGE ( 'NONE', *, *, #52647, .F. ) ; +#11270 = EDGE_CURVE ( 'NONE', #33079, #82338, #56874, .T. ) ; +#11271 = ORIENTED_EDGE ( 'NONE', *, *, #40898, .T. ) ; +#11272 = ADVANCED_FACE ( 'NONE', ( #16482 ), #47668, .F. ) ; +#11273 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#11274 = DIRECTION ( 'NONE', ( 0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#11275 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8099999999999502043 ) ) ; +#11276 = VECTOR ( 'NONE', #2150, 1000.000000000000000 ) ; +#11277 = SURFACE_SIDE_STYLE ('',( #81351 ) ) ; +#11279 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#11278 = CARTESIAN_POINT ( 'NONE', ( 0.2827097938661469745, -0.9901059572320288771, 0.8100000000000000533 ) ) ; +#11280 = ORIENTED_EDGE ( 'NONE', *, *, #44330, .F. ) ; +#11282 = ORIENTED_EDGE ( 'NONE', *, *, #42294, .F. ) ; +#11281 = EDGE_LOOP ( 'NONE', ( #35026, #87051, #56966, #48707, #61582, #100386 ) ) ; +#11283 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11284 = VERTEX_POINT ( 'NONE', #37760 ) ; +#11285 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11286 = VECTOR ( 'NONE', #8796, 1000.000000000000114 ) ; +#11287 = VERTEX_POINT ( 'NONE', #10787 ) ; +#11288 = EDGE_LOOP ( 'NONE', ( #76427, #41513, #49159, #92300 ) ) ; +#11289 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11290 = ADVANCED_FACE ( 'NONE', ( #75069 ), #59783, .T. ) ; +#11291 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11292 = DIRECTION ( 'NONE', ( 1.084202172485504237E-15, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11293 = ORIENTED_EDGE ( 'NONE', *, *, #87434, .F. ) ; +#11294 = LINE ( 'NONE', #32364, #45480 ) ; +#11295 = VERTEX_POINT ( 'NONE', #13186 ) ; +#11296 = EDGE_CURVE ( 'NONE', #49085, #21633, #13448, .T. ) ; +#11297 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220085265, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#11298 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11299 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -11.36999999999999922 ) ) ; +#11300 = STYLED_ITEM ( 'NONE', ( #78000 ), #9893 ) ; +#11301 = CARTESIAN_POINT ( 'NONE', ( 1.793081130502420129, -1.407725713391660083, 0.8100000000000000533 ) ) ; +#11302 = EDGE_CURVE ( 'NONE', #73986, #57093, #5068, .T. ) ; +#11303 = LINE ( 'NONE', #56891, #67927 ) ; +#11304 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#11305 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11307 = EDGE_CURVE ( 'NONE', #29731, #74398, #6036, .T. ) ; +#11306 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11308 = MANIFOLD_SOLID_BREP ( 'ÊäÈë159', #12551 ) ; +#11309 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5 ), #34248 ) ; +#11310 = LINE ( 'NONE', #35426, #33698 ) ; +#11311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11313 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11312 = CARTESIAN_POINT ( 'NONE', ( 0.3772639059291220121, -0.9641561732637019544, 0.8100000000000000533 ) ) ; +#11314 = FILL_AREA_STYLE_COLOUR ( '', #43714 ) ; +#11315 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11316 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81570 ) ) ; +#11317 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#11318 = CARTESIAN_POINT ( 'NONE', ( 1.157135261321870168, -0.8867570690059840555, 0.8299999999999999600 ) ) ; +#11319 = ORIENTED_EDGE ( 'NONE', *, *, #46194, .T. ) ; +#11320 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#11321 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#11322 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#11323 = CARTESIAN_POINT ( 'NONE', ( 4.383998436866569648, 1.420302575083351782, -11.91993319782745964 ) ) ; +#11324 = AXIS2_PLACEMENT_3D ( 'NONE', #70267, #69215, #21797 ) ; +#11325 = VECTOR ( 'NONE', #80854, 1000.000000000000000 ) ; +#11326 = ORIENTED_EDGE ( 'NONE', *, *, #66998, .F. ) ; +#11327 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11328 = CARTESIAN_POINT ( 'NONE', ( -0.9365963522183331502, -1.249140550102370018, 0.8300000000000002931 ) ) ; +#11329 = EDGE_CURVE ( 'NONE', #42002, #93347, #10150, .T. ) ; +#11330 = SURFACE_STYLE_FILL_AREA ( #31504 ) ; +#11331 = SURFACE_STYLE_FILL_AREA ( #43554 ) ; +#11332 = CARTESIAN_POINT ( 'NONE', ( 1.599803260885760192, -1.408946430034399899, 0.8099999999999976108 ) ) ; +#11333 = AXIS2_PLACEMENT_3D ( 'NONE', #41917, #73054, #3104 ) ; +#11334 = CARTESIAN_POINT ( 'NONE', ( -0.1900794716924300021, -1.425091422160009946, 0.8299999999999999600 ) ) ; +#11335 = FACE_OUTER_BOUND ( 'NONE', #85882, .T. ) ; +#11336 = VECTOR ( 'NONE', #4543, 1000.000000000000114 ) ; +#11337 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11338 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11339 = SURFACE_SIDE_STYLE ('',( #28267 ) ) ; +#11340 = AXIS2_PLACEMENT_3D ( 'NONE', #62321, #32180, #8083 ) ; +#11341 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11342 = ORIENTED_EDGE ( 'NONE', *, *, #74425, .F. ) ; +#11343 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#11344 = EDGE_CURVE ( 'NONE', #33857, #73926, #60267, .T. ) ; +#11345 = AXIS2_PLACEMENT_3D ( 'NONE', #49175, #94594, #95086 ) ; +#11346 = LINE ( 'NONE', #66552, #22898 ) ; +#11347 = LINE ( 'NONE', #81418, #85636 ) ; +#11348 = CARTESIAN_POINT ( 'NONE', ( 0.9858795606121630861, -1.017871276266119951, 0.8299999999999994049 ) ) ; +#11349 = PLANE ( 'NONE', #10928 ) ; +#11350 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68483 ), #52269 ) ; +#11351 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#11352 = SURFACE_STYLE_USAGE ( .BOTH. , #26780 ) ; +#11353 = EDGE_CURVE ( 'NONE', #32909, #88242, #23970, .T. ) ; +#11354 = SURFACE_SIDE_STYLE ('',( #42091 ) ) ; +#11355 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753240063, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#11356 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999993427, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#11357 = FILL_AREA_STYLE_COLOUR ( '', #9976 ) ; +#11358 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17964, 'distance_accuracy_value', 'NONE'); +#11359 = LINE ( 'NONE', #90558, #7636 ) ; +#11360 = FACE_OUTER_BOUND ( 'NONE', #78029, .T. ) ; +#11361 = AXIS2_PLACEMENT_3D ( 'NONE', #68277, #60656, #43806 ) ; +#11362 = FACE_OUTER_BOUND ( 'NONE', #39, .T. ) ; +#11363 = VECTOR ( 'NONE', #9840, 1000.000000000000000 ) ; +#11364 = ORIENTED_EDGE ( 'NONE', *, *, #78658, .F. ) ; +#11365 = SURFACE_STYLE_FILL_AREA ( #9358 ) ; +#11366 = ORIENTED_EDGE ( 'NONE', *, *, #93799, .F. ) ; +#11367 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35714, 'distance_accuracy_value', 'NONE'); +#11368 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84776, 'distance_accuracy_value', 'NONE'); +#11369 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65058, #3275, #90543 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11370 = SURFACE_SIDE_STYLE ('',( #96194 ) ) ; +#11371 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#11372 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11373 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959499, 0.000000000000000000 ) ) ; +#11374 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11375 = ORIENTED_EDGE ( 'NONE', *, *, #25118, .F. ) ; +#11376 = PRESENTATION_STYLE_ASSIGNMENT (( #48784 ) ) ; +#11377 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6392, 'distance_accuracy_value', 'NONE'); +#11378 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -7.346839692639300209E-32 ) ) ; +#11379 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11380 = ORIENTED_EDGE ( 'NONE', *, *, #824, .T. ) ; +#11381 = PRESENTATION_STYLE_ASSIGNMENT (( #32948 ) ) ; +#11382 = ADVANCED_FACE ( 'NONE', ( #77549 ), #85196, .F. ) ; +#11384 = EDGE_CURVE ( 'NONE', #27209, #14320, #20017, .T. ) ; +#11383 = STYLED_ITEM ( 'NONE', ( #23765 ), #10193 ) ; +#11385 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 3.287228999999999957, 0.8648700000000000276 ) ) ; +#11386 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11387 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109697000000000600, 0.8991599999999999593 ) ) ; +#11388 = EDGE_LOOP ( 'NONE', ( #47652, #3870, #55875, #46114, #24079 ) ) ; +#11389 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#11390 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49027 ) ) ; +#11391 = LINE ( 'NONE', #20631, #1678 ) ; +#11392 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74484, 'distance_accuracy_value', 'NONE'); +#11393 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#11394 = CARTESIAN_POINT ( 'NONE', ( 1.841287855068439949, -1.152628822534790043, 0.8099999999999998312 ) ) ; +#11395 = ORIENTED_EDGE ( 'NONE', *, *, #56402, .F. ) ; +#11396 = ADVANCED_FACE ( 'NONE', ( #94363 ), #9036, .T. ) ; +#11397 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000019873, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#11398 = CARTESIAN_POINT ( 'NONE', ( -1.135336132237972917, -1.229126379814545311, 0.8099999999998193090 ) ) ; +#11399 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#11400 = ORIENTED_EDGE ( 'NONE', *, *, #93270, .T. ) ; +#11401 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11402 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #8373, #46218 ), + ( #100755, #91701 ), + ( #78413, #92206 ), + ( #77390, #39613 ), + ( #93677, #22273 ), + ( #70749, #77906 ), + ( #22784, #23294 ), + ( #52938, #70234 ), + ( #794, #7374 ), + ( #30936, #62122 ), + ( #31957, #84068 ), + ( #14062, #23805 ), + ( #69190, #45220 ), + ( #76387, #38601 ), + ( #6388, #84551 ), + ( #37616, #15592 ), + ( #39107, #76903 ), + ( #93182, #6861 ), + ( #86063, #45713 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06797158385402859992, 0.1342600110226029875, 0.1996375432477019984, 0.2636133251149819778, 0.3266798409903740041, 0.3873044356296519997, 0.4467275391483779834, 0.5050530114610609633, 0.5632809992818490485, 0.6212441432870500213, 0.6796615349141380547, 0.7395831398408979629, 0.8010350593152619769, 0.8644459444340329979, 0.9304086162470880383, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#11403 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26147 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46251, #32502, #24865 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11404 = AXIS2_PLACEMENT_3D ( 'NONE', #38672, #6939, #99357 ) ; +#11405 = ORIENTED_EDGE ( 'NONE', *, *, #94874, .F. ) ; +#11408 = ORIENTED_EDGE ( 'NONE', *, *, #25904, .F. ) ; +#11407 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11406 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65284 ) ) ; +#11409 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11410 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11412 = SURFACE_STYLE_FILL_AREA ( #19138 ) ; +#11411 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11413 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11414 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11415 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#11416 = DIRECTION ( 'NONE', ( -1.000000000000000000, -9.346570452461245291E-17, 0.000000000000000000 ) ) ; +#11417 = ORIENTED_EDGE ( 'NONE', *, *, #41340, .T. ) ; +#11418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14737 ), #86502 ) ; +#11419 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11420 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#11421 = LINE ( 'NONE', #90109, #93892 ) ; +#11422 = ORIENTED_EDGE ( 'NONE', *, *, #72048, .T. ) ; +#11423 = CIRCLE ( 'NONE', #79969, 0.009999999999999998473 ) ; +#11424 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999620541 ) ) ; +#11425 = EDGE_LOOP ( 'NONE', ( #60093, #33551, #7994, #95070 ) ) ; +#11427 = LINE ( 'NONE', #35031, #4335 ) ; +#11426 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11428 = AXIS2_PLACEMENT_3D ( 'NONE', #43671, #5345, #50869 ) ; +#11429 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11430 = STYLED_ITEM ( 'NONE', ( #5225 ), #2054 ) ; +#11432 = EDGE_CURVE ( 'NONE', #96849, #97292, #100504, .T. ) ; +#11431 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#11433 = ORIENTED_EDGE ( 'NONE', *, *, #55651, .F. ) ; +#11434 = VECTOR ( 'NONE', #7638, 1000.000000000000000 ) ; +#11435 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#11436 = SURFACE_STYLE_FILL_AREA ( #73817 ) ; +#11437 = EDGE_LOOP ( 'NONE', ( #80474, #1216, #2034, #8128 ) ) ; +#11438 = PRESENTATION_STYLE_ASSIGNMENT (( #91508 ) ) ; +#11439 = EDGE_LOOP ( 'NONE', ( #53569, #50964, #16997, #47952 ) ) ; +#11440 = FACE_OUTER_BOUND ( 'NONE', #90705, .T. ) ; +#11441 = CARTESIAN_POINT ( 'NONE', ( -1.116693831898450062, -1.233317951191559958, 0.8299999999999999600 ) ) ; +#11443 = DIRECTION ( 'NONE', ( 0.7071067811865470176, 0.7071067811865480168, 8.659560562354925463E-17 ) ) ; +#11442 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7070 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78783, #79300, #71648 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11444 = FACE_OUTER_BOUND ( 'NONE', #2369, .T. ) ; +#11445 = ORIENTED_EDGE ( 'NONE', *, *, #68362, .F. ) ; +#11446 = PRESENTATION_STYLE_ASSIGNMENT (( #80495 ) ) ; +#11447 = LINE ( 'NONE', #89155, #49735 ) ; +#11448 = ADVANCED_FACE ( 'NONE', ( #39764 ), #53583, .T. ) ; +#11449 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#11450 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#11451 = VECTOR ( 'NONE', #86818, 1000.000000000000000 ) ; +#11452 = FILL_AREA_STYLE ('',( #73352 ) ) ; +#11453 = PLANE ( 'NONE', #58306 ) ; +#11454 = FACE_OUTER_BOUND ( 'NONE', #7619, .T. ) ; +#11455 = VERTEX_POINT ( 'NONE', #64755 ) ; +#11456 = EDGE_CURVE ( 'NONE', #79322, #25243, #56631, .T. ) ; +#11457 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11458 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11459 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11460 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.9000000000000003553, -0.02000000000001884992 ) ) ; +#11461 = STYLED_ITEM ( 'NONE', ( #82984 ), #18077 ) ; +#11462 = CIRCLE ( 'NONE', #49112, 0.009999999999999998473 ) ; +#11463 = FILL_AREA_STYLE ('',( #66187 ) ) ; +#11464 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11465 = PRESENTATION_STYLE_ASSIGNMENT (( #19200 ) ) ; +#11466 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#11467 = PRESENTATION_STYLE_ASSIGNMENT (( #90155 ) ) ; +#11468 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68604 ) ) ; +#11470 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11469 = VECTOR ( 'NONE', #22184, 999.9999999999998863 ) ; +#11471 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52327 ) ) ; +#11472 = PRESENTATION_STYLE_ASSIGNMENT (( #50897 ) ) ; +#11473 = CARTESIAN_POINT ( 'NONE', ( 1.876179938779914957, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#11474 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8648700000000000276 ) ) ; +#11475 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#11476 = MANIFOLD_SOLID_BREP ( 'ÊäÈë156', #55070 ) ; +#11477 = EDGE_CURVE ( 'NONE', #60265, #93582, #48456, .T. ) ; +#11478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7363 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69797, #77468, #62690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11479 = CARTESIAN_POINT ( 'NONE', ( -0.7486880133853439645, 1.376284075926970107, 0.8100000000000000533 ) ) ; +#11480 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11481 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18022 ), #44136 ) ; +#11482 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#11483 = FACE_OUTER_BOUND ( 'NONE', #92631, .T. ) ; +#11484 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11486 = EDGE_CURVE ( 'NONE', #89708, #47747, #92123, .T. ) ; +#11485 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#11487 = ORIENTED_EDGE ( 'NONE', *, *, #33809, .F. ) ; +#11488 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11489 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#11490 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75346, 'distance_accuracy_value', 'NONE'); +#11491 = SURFACE_STYLE_USAGE ( .BOTH. , #9975 ) ; +#11492 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43764, 'distance_accuracy_value', 'NONE'); +#11493 = VECTOR ( 'NONE', #59458, 1000.000000000000114 ) ; +#11494 = FILL_AREA_STYLE_COLOUR ( '', #42640 ) ; +#11495 = ADVANCED_FACE ( 'NONE', ( #79585 ), #48950, .T. ) ; +#11496 = ADVANCED_FACE ( 'NONE', ( #99321 ), #74439, .T. ) ; +#11497 = CARTESIAN_POINT ( 'NONE', ( 0.4555072436079976028, -1.012915397863445532, 0.8099999999999999423 ) ) ; +#11498 = VECTOR ( 'NONE', #6200, 1000.000000000000000 ) ; +#11499 = ORIENTED_EDGE ( 'NONE', *, *, #50921, .T. ) ; +#11500 = VECTOR ( 'NONE', #34115, 1000.000000000000000 ) ; +#11501 = FILL_AREA_STYLE_COLOUR ( '', #37438 ) ; +#11502 = PRESENTATION_STYLE_ASSIGNMENT (( #17720 ) ) ; +#11503 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26334 ), #96398 ) ; +#11504 = SURFACE_STYLE_FILL_AREA ( #57594 ) ; +#11505 = EDGE_CURVE ( 'NONE', #67739, #15107, #35655, .T. ) ; +#11506 = ADVANCED_FACE ( 'NONE', ( #98329 ), #27476, .T. ) ; +#11507 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.499999999999969802, 0.1829999999999999960 ) ) ; +#11508 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5384, 'distance_accuracy_value', 'NONE'); +#11509 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#11510 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87628, 'distance_accuracy_value', 'NONE'); +#11511 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97763 ) ) ; +#11512 = FILL_AREA_STYLE ('',( #42743 ) ) ; +#11513 = ORIENTED_EDGE ( 'NONE', *, *, #30086, .F. ) ; +#11514 = ORIENTED_EDGE ( 'NONE', *, *, #100880, .F. ) ; +#11515 = EDGE_CURVE ( 'NONE', #63998, #47168, #51475, .T. ) ; +#11516 = SURFACE_SIDE_STYLE ('',( #88700 ) ) ; +#11517 = FILL_AREA_STYLE_COLOUR ( '', #42577 ) ; +#11518 = ORIENTED_EDGE ( 'NONE', *, *, #13125, .T. ) ; +#11520 = CARTESIAN_POINT ( 'NONE', ( 1.803030467297160211, -1.264112177694660000, 0.8100000000000000533 ) ) ; +#11519 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11521 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11522 = PLANE ( 'NONE', #26864 ) ; +#11523 = STYLED_ITEM ( 'NONE', ( #6021 ), #10660 ) ; +#11524 = ADVANCED_FACE ( 'NONE', ( #60148 ), #91243, .T. ) ; +#11525 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #73010, #58257 ) ; +#11526 = FILL_AREA_STYLE ('',( #42270 ) ) ; +#11527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#11529 = EDGE_LOOP ( 'NONE', ( #55613, #96610, #77060, #31340, #67389, #95884 ) ) ; +#11528 = ORIENTED_EDGE ( 'NONE', *, *, #6535, .T. ) ; +#11530 = STYLED_ITEM ( 'NONE', ( #63110 ), #45494 ) ; +#11531 = ORIENTED_EDGE ( 'NONE', *, *, #81231, .T. ) ; +#11532 = ORIENTED_EDGE ( 'NONE', *, *, #23324, .F. ) ; +#11533 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11534 = FILL_AREA_STYLE ('',( #72908 ) ) ; +#11536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11535 = LINE ( 'NONE', #42768, #68749 ) ; +#11537 = VERTEX_POINT ( 'NONE', #39637 ) ; +#11538 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.000000000000000000 ) ) ; +#11539 = VECTOR ( 'NONE', #26190, 1000.000000000000000 ) ; +#11540 = CARTESIAN_POINT ( 'NONE', ( -1.289503315023140084, -0.9165513359838141083, 0.8100000000000000533 ) ) ; +#11541 = ORIENTED_EDGE ( 'NONE', *, *, #30096, .F. ) ; +#11542 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#11543 = ORIENTED_EDGE ( 'NONE', *, *, #54450, .T. ) ; +#11544 = ORIENTED_EDGE ( 'NONE', *, *, #41351, .F. ) ; +#11545 = CARTESIAN_POINT ( 'NONE', ( 0.2346921643439940086, -1.433080367293090074, 0.8300000000000004041 ) ) ; +#11546 = SURFACE_SIDE_STYLE ('',( #98331 ) ) ; +#11548 = EDGE_CURVE ( 'NONE', #28082, #87717, #92713, .T. ) ; +#11547 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#11549 = VECTOR ( 'NONE', #32645, 1000.000000000000000 ) ; +#11551 = ORIENTED_EDGE ( 'NONE', *, *, #72742, .F. ) ; +#11550 = FILL_AREA_STYLE ('',( #3494 ) ) ; +#11552 = STYLED_ITEM ( 'NONE', ( #86112 ), #8152 ) ; +#11553 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999901329, 0.4700000000088402907, 0.6499230723514386465 ) ) ; +#11554 = EDGE_LOOP ( 'NONE', ( #2475, #85792, #15613, #100515 ) ) ; +#11555 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61564 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3139, #88401, #65405 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11556 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11557 = ORIENTED_EDGE ( 'NONE', *, *, #99319, .F. ) ; +#11558 = LINE ( 'NONE', #42793, #69325 ) ; +#11559 = PLANE ( 'NONE', #16720 ) ; +#11560 = ORIENTED_EDGE ( 'NONE', *, *, #41036, .F. ) ; +#11561 = EDGE_CURVE ( 'NONE', #16927, #12266, #15092, .T. ) ; +#11562 = VERTEX_POINT ( 'NONE', #16622 ) ; +#11564 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#11563 = CARTESIAN_POINT ( 'NONE', ( 0.5232566677822769741, -0.9829422030519651132, 0.8299999999999992939 ) ) ; +#11565 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11566 = LINE ( 'NONE', #72415, #88990 ) ; +#11567 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31183 ) ) ; +#11568 = FACE_OUTER_BOUND ( 'NONE', #40547, .T. ) ; +#11569 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#11570 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20442, #96525, #66415, #18423 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#11571 = FILL_AREA_STYLE_COLOUR ( '', #44202 ) ; +#11572 = FILL_AREA_STYLE ('',( #4972 ) ) ; +#11573 = ORIENTED_EDGE ( 'NONE', *, *, #27258, .T. ) ; +#11574 = CYLINDRICAL_SURFACE ( 'NONE', #65960, 0.04999999999999991257 ) ; +#11575 = ORIENTED_EDGE ( 'NONE', *, *, #72303, .T. ) ; +#11576 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13249 ), #41062 ) ; +#11577 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#11578 = FACE_OUTER_BOUND ( 'NONE', #25050, .T. ) ; +#11579 = CARTESIAN_POINT ( 'NONE', ( 1.164415487177949959, -1.144973971495400145, 0.8100000000000000533 ) ) ; +#11580 = LINE ( 'NONE', #97882, #65991 ) ; +#11581 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#11582 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#11583 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11584 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#11585 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11586 = ORIENTED_EDGE ( 'NONE', *, *, #83416, .T. ) ; +#11587 = EDGE_CURVE ( 'NONE', #84912, #88475, #38624, .T. ) ; +#11588 = FILL_AREA_STYLE ('',( #82634 ) ) ; +#11589 = CARTESIAN_POINT ( 'NONE', ( 0.2049220250908939944, -0.9740213618777919802, 0.8300000000000009592 ) ) ; +#11590 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#11591 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#11592 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11593 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11594 = STYLED_ITEM ( 'NONE', ( #37627 ), #46356 ) ; +#11595 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#11596 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11597 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#11598 = LINE ( 'NONE', #11095, #3043 ) ; +#11600 = STYLED_ITEM ( 'NONE', ( #66484 ), #45768 ) ; +#11599 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11601 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11602 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87306, 'distance_accuracy_value', 'NONE'); +#11603 = VERTEX_POINT ( 'NONE', #93210 ) ; +#11604 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11605 = CARTESIAN_POINT ( 'NONE', ( 1.515867623847370282, -1.051115598670280038, 0.8299999999999999600 ) ) ; +#11606 = LINE ( 'NONE', #42849, #19802 ) ; +#11607 = VERTEX_POINT ( 'NONE', #85588 ) ; +#11608 = STYLED_ITEM ( 'NONE', ( #67409 ), #18488 ) ; +#11609 = CARTESIAN_POINT ( 'NONE', ( 1.715925389647680044, -0.9637996098261990552, 0.8100000000000006084 ) ) ; +#11610 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100969 ) ; +#11611 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #247 ) ) ; +#11612 = SURFACE_STYLE_USAGE ( .BOTH. , #64827 ) ; +#11613 = ORIENTED_EDGE ( 'NONE', *, *, #79873, .F. ) ; +#11614 = VERTEX_POINT ( 'NONE', #23320 ) ; +#11615 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11616 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55750 ) ) ; +#11617 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.000000000000000000, -12.01999999999999957 ) ) ; +#11618 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11619 = ADVANCED_FACE ( 'NONE', ( #93711 ), #37641, .T. ) ; +#11620 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11621 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15023, 'distance_accuracy_value', 'NONE'); +#11622 = CYLINDRICAL_SURFACE ( 'NONE', #66121, 0.1000000000000000472 ) ; +#11623 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11624 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75408, #74922, #82586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11625 = CARTESIAN_POINT ( 'NONE', ( -1.369924375369726555, -1.000424401669817165, 0.8099999999999876188 ) ) ; +#11626 = FILL_AREA_STYLE ('',( #50557 ) ) ; +#11627 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86714 ), #99642 ) ; +#11628 = ORIENTED_EDGE ( 'NONE', *, *, #49405, .T. ) ; +#11629 = LINE ( 'NONE', #10111, #14443 ) ; +#11630 = VECTOR ( 'NONE', #58210, 1000.000000000000000 ) ; +#11631 = ORIENTED_EDGE ( 'NONE', *, *, #61743, .T. ) ; +#11632 = CARTESIAN_POINT ( 'NONE', ( 6.367832249750026818, 1.979081249750024307, 0.8991599999999999593 ) ) ; +#11633 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11634 = LINE ( 'NONE', #42876, #45234 ) ; +#11635 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#11636 = EDGE_CURVE ( 'NONE', #6033, #58131, #31983, .T. ) ; +#11637 = CARTESIAN_POINT ( 'NONE', ( 9.252828249749912359, 2.827609249749912568, 0.8648700000000000276 ) ) ; +#11638 = CARTESIAN_POINT ( 'NONE', ( -0.3688392660424539837, -1.039320398944010071, 0.8100000000000000533 ) ) ; +#11639 = CARTESIAN_POINT ( 'NONE', ( -0.07284665700025037827, 0.8294401816296989027, 0.8100000000000002753 ) ) ; +#11640 = FACE_OUTER_BOUND ( 'NONE', #81587, .T. ) ; +#11642 = ORIENTED_EDGE ( 'NONE', *, *, #15528, .F. ) ; +#11641 = ORIENTED_EDGE ( 'NONE', *, *, #31548, .F. ) ; +#11643 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94856 ), #72092 ) ; +#11644 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11645 = ORIENTED_EDGE ( 'NONE', *, *, #55961, .F. ) ; +#11646 = LINE ( 'NONE', #4567, #34991 ) ; +#11647 = ORIENTED_EDGE ( 'NONE', *, *, #76261, .T. ) ; +#11648 = ORIENTED_EDGE ( 'NONE', *, *, #39263, .T. ) ; +#11650 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#11649 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11651 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#11652 = VERTEX_POINT ( 'NONE', #86092 ) ; +#11653 = EDGE_LOOP ( 'NONE', ( #25326, #41031, #8135, #74334 ) ) ; +#11654 = SURFACE_STYLE_USAGE ( .BOTH. , #5065 ) ; +#11655 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41110 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83340, #54202, #23067 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11656 = ORIENTED_EDGE ( 'NONE', *, *, #86872, .T. ) ; +#11657 = SURFACE_SIDE_STYLE ('',( #34770 ) ) ; +#11658 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#11659 = EDGE_CURVE ( 'NONE', #63443, #95595, #27611, .T. ) ; +#11660 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9145, #77660, #86323 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11662 = ORIENTED_EDGE ( 'NONE', *, *, #70618, .F. ) ; +#11661 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11663 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8648700000000000276 ) ) ; +#11664 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11665 = VERTEX_POINT ( 'NONE', #77422 ) ; +#11666 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#11667 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8648700000000000276 ) ) ; +#11668 = VERTEX_POINT ( 'NONE', #47290 ) ; +#11669 = EDGE_CURVE ( 'NONE', #15372, #86461, #61639, .T. ) ; +#11670 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11671 = ORIENTED_EDGE ( 'NONE', *, *, #81911, .T. ) ; +#11672 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#11673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11674 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65545 ), #96505 ) ; +#11675 = FILL_AREA_STYLE_COLOUR ( '', #12716 ) ; +#11676 = LINE ( 'NONE', #3112, #17166 ) ; +#11677 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80305 ) ) ; +#11678 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11679 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11680 = VECTOR ( 'NONE', #51407, 1000.000000000000114 ) ; +#11681 = PLANE ( 'NONE', #92210 ) ; +#11682 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#11683 = ORIENTED_EDGE ( 'NONE', *, *, #71200, .F. ) ; +#11684 = PLANE ( 'NONE', #55556 ) ; +#11686 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#11685 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #65081, #82675 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #72269 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#11687 = ORIENTED_EDGE ( 'NONE', *, *, #61123, .F. ) ; +#11688 = VECTOR ( 'NONE', #7262, 1000.000000000000000 ) ; +#11689 = FACE_OUTER_BOUND ( 'NONE', #83204, .T. ) ; +#11690 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67235 ) ) ; +#11691 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#11692 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11693 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83588 ), #80322 ) ; +#11694 = FACE_OUTER_BOUND ( 'NONE', #65249, .T. ) ; +#11696 = SURFACE_STYLE_FILL_AREA ( #64915 ) ; +#11695 = CARTESIAN_POINT ( 'NONE', ( 1.296446609406726402, 0.7099999999999999645, -1.050000000000000266 ) ) ; +#11697 = DIRECTION ( 'NONE', ( -0.7071045084557425753, -0.7071090539100477468, 0.000000000000000000 ) ) ; +#11698 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11699 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#11700 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11701 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86798 ) ) ; +#11702 = ADVANCED_FACE ( 'NONE', ( #73318 ), #32499, .T. ) ; +#11703 = LINE ( 'NONE', #4139, #36802 ) ; +#11704 = VERTEX_POINT ( 'NONE', #25363 ) ; +#11705 = VECTOR ( 'NONE', #73627, 1000.000000000000000 ) ; +#11706 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11708 = PLANE ( 'NONE', #44536 ) ; +#11707 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#11709 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71606 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86353, #61885, #31726 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11710 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11711 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11712 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24978, 'distance_accuracy_value', 'NONE'); +#11713 = ORIENTED_EDGE ( 'NONE', *, *, #127, .F. ) ; +#11714 = ADVANCED_FACE ( 'NONE', ( #89128 ), #41673, .T. ) ; +#11715 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11716 = EDGE_CURVE ( 'NONE', #60865, #26980, #1342, .T. ) ; +#11717 = PLANE ( 'NONE', #448 ) ; +#11718 = FACE_OUTER_BOUND ( 'NONE', #92544, .T. ) ; +#11719 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11720 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52571 ) ) ; +#11721 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55859 ) ) ; +#11722 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#11723 = DIRECTION ( 'NONE', ( 0.7071067811865455743, -0.7071067811865495711, 0.000000000000000000 ) ) ; +#11724 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11725 = VERTEX_POINT ( 'NONE', #41168 ) ; +#11726 = AXIS2_PLACEMENT_3D ( 'NONE', #28360, #82983, #42679 ) ; +#11727 = VERTEX_POINT ( 'NONE', #49320 ) ; +#11728 = LINE ( 'NONE', #96564, #97530 ) ; +#11729 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85964, 'distance_accuracy_value', 'NONE'); +#11730 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11731 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11732 = EDGE_CURVE ( 'NONE', #54703, #36433, #2360, .T. ) ; +#11733 = CARTESIAN_POINT ( 'NONE', ( 0.5288443359852855741, -1.157344751858137011, 0.8100000000000002753 ) ) ; +#11734 = LINE ( 'NONE', #96065, #24886 ) ; +#11735 = FACE_OUTER_BOUND ( 'NONE', #70230, .T. ) ; +#11736 = AXIS2_PLACEMENT_3D ( 'NONE', #63066, #9344, #238 ) ; +#11737 = FILL_AREA_STYLE_COLOUR ( '', #100910 ) ; +#11738 = ORIENTED_EDGE ( 'NONE', *, *, #16501, .F. ) ; +#11739 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11740 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.899999999999999911, 0.000000000000000000 ) ) ; +#11741 = ORIENTED_EDGE ( 'NONE', *, *, #41661, .T. ) ; +#11742 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11743 = VECTOR ( 'NONE', #78355, 1000.000000000000114 ) ; +#11744 = SURFACE_STYLE_FILL_AREA ( #82317 ) ; +#11745 = ORIENTED_EDGE ( 'NONE', *, *, #28638, .F. ) ; +#11746 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52605 ), #18305 ) ; +#11747 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11748 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11749 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11750 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#11751 = EDGE_CURVE ( 'NONE', #58587, #51509, #63652, .T. ) ; +#11752 = VECTOR ( 'NONE', #36461, 1000.000000000000000 ) ; +#11753 = SURFACE_STYLE_USAGE ( .BOTH. , #34364 ) ; +#11754 = SURFACE_STYLE_FILL_AREA ( #28190 ) ; +#11755 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#11756 = ORIENTED_EDGE ( 'NONE', *, *, #38351, .F. ) ; +#11757 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80385 ) ) ; +#11758 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#11759 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31456 ) ) ; +#11760 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#11761 = ORIENTED_EDGE ( 'NONE', *, *, #99917, .T. ) ; +#11762 = PLANE ( 'NONE', #83484 ) ; +#11763 = VECTOR ( 'NONE', #84218, 1000.000000000000000 ) ; +#11764 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.300000000000000044, 0.000000000000000000 ) ) ; +#11765 = ORIENTED_EDGE ( 'NONE', *, *, #23245, .T. ) ; +#11766 = ORIENTED_EDGE ( 'NONE', *, *, #94780, .T. ) ; +#11767 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11768 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558440262, -1.079220779220779969, 0.8100000000000000533 ) ) ; +#11769 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31393 ), #82002 ) ; +#11770 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11771 = ORIENTED_EDGE ( 'NONE', *, *, #98890, .T. ) ; +#11773 = ORIENTED_EDGE ( 'NONE', *, *, #11922, .F. ) ; +#11772 = ORIENTED_EDGE ( 'NONE', *, *, #37541, .F. ) ; +#11774 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #45807, #68310, #37699, #99854, #60686, #74998, #67798, #6475, #76985, #5006, #91792, #61696, #98384 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1249999999999997780, 0.2499999999999995559, 0.3749999999999993339, 0.4374999999999992228, 0.4999999999999991118, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#11775 = ORIENTED_EDGE ( 'NONE', *, *, #75591, .T. ) ; +#11776 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11777 = EDGE_CURVE ( 'NONE', #99864, #51935, #96749, .T. ) ; +#11778 = VERTEX_POINT ( 'NONE', #17140 ) ; +#11780 = EDGE_LOOP ( 'NONE', ( #97126, #77458, #21484, #91694 ) ) ; +#11779 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#11781 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11782 = LINE ( 'NONE', #67003, #2445 ) ; +#11783 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#11784 = AXIS2_PLACEMENT_3D ( 'NONE', #25066, #41873, #25558 ) ; +#11785 = ORIENTED_EDGE ( 'NONE', *, *, #81405, .T. ) ; +#11786 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#11787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11788 = ORIENTED_EDGE ( 'NONE', *, *, #73321, .F. ) ; +#11789 = EDGE_CURVE ( 'NONE', #34637, #72729, #45804, .T. ) ; +#11790 = PRESENTATION_STYLE_ASSIGNMENT (( #91867 ) ) ; +#11791 = CARTESIAN_POINT ( 'NONE', ( 0.2641833960299687090, -1.376599916188856243, 0.8099999999999999423 ) ) ; +#11792 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#11793 = STYLED_ITEM ( 'NONE', ( #13349 ), #87795 ) ; +#11794 = CARTESIAN_POINT ( 'NONE', ( 0.5335638015470970386, -1.143334495870530265, 0.8299999999999999600 ) ) ; +#11795 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29645 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24303, #40106, #63096 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11796 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11797 = AXIS2_PLACEMENT_3D ( 'NONE', #29543, #19876, #45330 ) ; +#11798 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264148000000000494, 0.8991599999999999593 ) ) ; +#11799 = CARTESIAN_POINT ( 'NONE', ( 1.784639205958740149, -1.415447185383410078, 0.8299999999999999600 ) ) ; +#11801 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11800 = LINE ( 'NONE', #44037, #74105 ) ; +#11802 = SURFACE_STYLE_FILL_AREA ( #98097 ) ; +#11803 = LINE ( 'NONE', #19559, #96163 ) ; +#11804 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34977 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35042, #98710, #19173 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11805 = MANIFOLD_SOLID_BREP ( 'ÊäÈë71', #19104 ) ; +#11806 = ORIENTED_EDGE ( 'NONE', *, *, #45792, .F. ) ; +#11807 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4849999999999999867, -0.2400000000000000466 ) ) ; +#11808 = STYLED_ITEM ( 'NONE', ( #100464 ), #35926 ) ; +#11809 = FILL_AREA_STYLE ('',( #90006 ) ) ; +#11810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11811 = VECTOR ( 'NONE', #10878, 1000.000000000000000 ) ; +#11812 = STYLED_ITEM ( 'NONE', ( #39612 ), #37726 ) ; +#11813 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98203 ), #15061 ) ; +#11814 = VECTOR ( 'NONE', #83644, 1000.000000000000000 ) ; +#11815 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.900000000000000133, -0.02000000000000000042 ) ) ; +#11816 = CARTESIAN_POINT ( 'NONE', ( 1.033493568211090174, -0.9379159637996601351, 0.8100000000000000533 ) ) ; +#11817 = VERTEX_POINT ( 'NONE', #68120 ) ; +#11818 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11819 = ADVANCED_FACE ( 'NONE', ( #19158 ), #82974, .T. ) ; +#11820 = EDGE_CURVE ( 'NONE', #66369, #18005, #12938, .T. ) ; +#11821 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#11822 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11823 = LINE ( 'NONE', #34928, #77678 ) ; +#11824 = EDGE_LOOP ( 'NONE', ( #71154, #48554, #91081, #20032, #97841, #31930 ) ) ; +#11825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11826 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#11828 = PLANE ( 'NONE', #16678 ) ; +#11827 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11829 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6750 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37761, #31597, #92359 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11830 = CARTESIAN_POINT ( 'NONE', ( -0.2221370729066020344, -1.389169665048220148, 0.8100000000000000533 ) ) ; +#11831 = AXIS2_PLACEMENT_3D ( 'NONE', #22221, #21708, #45170 ) ; +#11832 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#11833 = FACE_OUTER_BOUND ( 'NONE', #79567, .T. ) ; +#11834 = SURFACE_STYLE_USAGE ( .BOTH. , #59940 ) ; +#11835 = ORIENTED_EDGE ( 'NONE', *, *, #81953, .T. ) ; +#11836 = PRESENTATION_STYLE_ASSIGNMENT (( #27275 ) ) ; +#11837 = EDGE_CURVE ( 'NONE', #27945, #17103, #21179, .T. ) ; +#11838 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#11839 = ADVANCED_FACE ( 'NONE', ( #58527 ), #89629, .F. ) ; +#11840 = FACE_OUTER_BOUND ( 'NONE', #18322, .T. ) ; +#11841 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#11842 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#11843 = LINE ( 'NONE', #18055, #67632 ) ; +#11844 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46048 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62102, #54431, #71236 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11845 = FACE_OUTER_BOUND ( 'NONE', #6430, .T. ) ; +#11846 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#11847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11848 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11849 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#11850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11851 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11852 = ORIENTED_EDGE ( 'NONE', *, *, #61087, .F. ) ; +#11853 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#11854 = VECTOR ( 'NONE', #37900, 1000.000000000000000 ) ; +#11855 = EDGE_LOOP ( 'NONE', ( #59668, #90903, #86272, #13273 ) ) ; +#11856 = PRESENTATION_STYLE_ASSIGNMENT (( #27806 ) ) ; +#11857 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#11858 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11859 = SURFACE_STYLE_USAGE ( .BOTH. , #19098 ) ; +#11860 = LINE ( 'NONE', #43582, #80504 ) ; +#11861 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11862 = LINE ( 'NONE', #66093, #58232 ) ; +#11863 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3796 ), #68984 ) ; +#11864 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.700000000000000178, 0.000000000000000000 ) ) ; +#11865 = ORIENTED_EDGE ( 'NONE', *, *, #33537, .F. ) ; +#11866 = CARTESIAN_POINT ( 'NONE', ( 1.106174479290626511, -1.421558282304846710, 0.8099999999997248290 ) ) ; +#11867 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11868 = EDGE_CURVE ( 'NONE', #20053, #22432, #16008, .T. ) ; +#11869 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81814, #97574, #57330, #34857 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#11870 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13402 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #721, #64041, #16526 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11871 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11872 = ORIENTED_EDGE ( 'NONE', *, *, #16501, .T. ) ; +#11873 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#11874 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#11875 = ADVANCED_FACE ( 'NONE', ( #45617 ), #70142, .T. ) ; +#11876 = SURFACE_STYLE_FILL_AREA ( #66105 ) ; +#11878 = EDGE_CURVE ( 'NONE', #27237, #24082, #13972, .T. ) ; +#11877 = SURFACE_STYLE_FILL_AREA ( #35489 ) ; +#11879 = STYLED_ITEM ( 'NONE', ( #77192 ), #76206 ) ; +#11880 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#11881 = VERTEX_POINT ( 'NONE', #76805 ) ; +#11882 = LINE ( 'NONE', #96707, #22151 ) ; +#11883 = LINE ( 'NONE', #52801, #79884 ) ; +#11884 = EDGE_CURVE ( 'NONE', #35659, #53854, #83976, .T. ) ; +#11885 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11886 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#11887 = VECTOR ( 'NONE', #24263, 1000.000000000000000 ) ; +#11888 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75530 ), #88575 ) ; +#11890 = STYLED_ITEM ( 'NONE', ( #69580 ), #21261 ) ; +#11889 = CARTESIAN_POINT ( 'NONE', ( 1.583412716359319905, -1.066507643917919745, 0.8099999999999994982 ) ) ; +#11891 = PRODUCT_DEFINITION ( 'δ֪', '', #38819, #49378 ) ; +#11892 = ORIENTED_EDGE ( 'NONE', *, *, #98157, .T. ) ; +#11893 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#11894 = FACE_OUTER_BOUND ( 'NONE', #34496, .T. ) ; +#11895 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#11896 = CARTESIAN_POINT ( 'NONE', ( -0.9904356460366252612, -1.311384449581599387, 0.8099999999997585798 ) ) ; +#11897 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#11898 = ORIENTED_EDGE ( 'NONE', *, *, #5531, .T. ) ; +#11899 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11900 = AXIS2_PLACEMENT_3D ( 'NONE', #67328, #13643, #44829 ) ; +#11901 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92404 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92909, #6614, #14291 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11902 = EDGE_CURVE ( 'NONE', #44343, #7897, #30841, .T. ) ; +#11903 = STYLED_ITEM ( 'NONE', ( #3976 ), #59920 ) ; +#11904 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11905 = EDGE_LOOP ( 'NONE', ( #73400, #10434, #5019, #23153 ) ) ; +#11907 = ORIENTED_EDGE ( 'NONE', *, *, #85154, .T. ) ; +#11906 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#11908 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #581, 'distance_accuracy_value', 'NONE'); +#11909 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11911 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11910 = FILL_AREA_STYLE ('',( #43135 ) ) ; +#11912 = SURFACE_STYLE_FILL_AREA ( #5299 ) ; +#11913 = SURFACE_STYLE_FILL_AREA ( #27338 ) ; +#11914 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#11915 = ORIENTED_EDGE ( 'NONE', *, *, #46893, .T. ) ; +#11916 = EDGE_CURVE ( 'NONE', #55619, #20637, #92118, .T. ) ; +#11917 = FILL_AREA_STYLE ('',( #58521 ) ) ; +#11918 = FILL_AREA_STYLE ('',( #12929 ) ) ; +#11919 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.593649167310369874, -11.41999999999999993 ) ) ; +#11920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46215 ) ) ; +#11921 = ORIENTED_EDGE ( 'NONE', *, *, #18286, .T. ) ; +#11922 = EDGE_CURVE ( 'NONE', #30759, #70520, #21836, .T. ) ; +#11923 = LINE ( 'NONE', #49839, #50264 ) ; +#11924 = ORIENTED_EDGE ( 'NONE', *, *, #12480, .T. ) ; +#11926 = FILL_AREA_STYLE ('',( #65137 ) ) ; +#11925 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11927 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#11929 = ADVANCED_FACE ( 'NONE', ( #38021 ), #69096, .F. ) ; +#11928 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#11930 = ORIENTED_EDGE ( 'NONE', *, *, #3158, .T. ) ; +#11931 = SURFACE_SIDE_STYLE ('',( #67621 ) ) ; +#11932 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#11933 = ORIENTED_EDGE ( 'NONE', *, *, #69316, .T. ) ; +#11934 = SURFACE_SIDE_STYLE ('',( #83985 ) ) ; +#11935 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11936 = ORIENTED_EDGE ( 'NONE', *, *, #23938, .F. ) ; +#11937 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#11938 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#11939 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.000000000000000000 ) ) ; +#11940 = VECTOR ( 'NONE', #21090, 1000.000000000000000 ) ; +#11941 = LINE ( 'NONE', #63307, #57235 ) ; +#11942 = VECTOR ( 'NONE', #37463, 1000.000000000000114 ) ; +#11943 = VECTOR ( 'NONE', #30158, 1000.000000000000000 ) ; +#11944 = EDGE_CURVE ( 'NONE', #73172, #32633, #70246, .T. ) ; +#11946 = ADVANCED_FACE ( 'NONE', ( #47682, #79855 ), #57385, .F. ) ; +#11945 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11947 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974019543, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#11948 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#11949 = EDGE_LOOP ( 'NONE', ( #22052, #6274, #69242, #46777 ) ) ; +#11950 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 1.458578643762689975, -0.02000000000000000042 ) ) ; +#11951 = LINE ( 'NONE', #98723, #75780 ) ; +#11952 = VECTOR ( 'NONE', #72078, 1000.000000000000000 ) ; +#11953 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980549, 0.000000000000000000 ) ) ; +#11954 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98028, 'distance_accuracy_value', 'NONE'); +#11955 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, 0.000000000000000000 ) ) ; +#11956 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 8.802661000000002289, 0.8991599999999999593 ) ) ; +#11957 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#11958 = DIRECTION ( 'NONE', ( -0.3444045651374290085, 0.000000000000000000, -0.9388213331153582031 ) ) ; +#11959 = VECTOR ( 'NONE', #30887, 1000.000000000000000 ) ; +#11960 = PRESENTATION_STYLE_ASSIGNMENT (( #13473 ) ) ; +#11961 = ORIENTED_EDGE ( 'NONE', *, *, #59392, .F. ) ; +#11962 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#11963 = PRESENTATION_STYLE_ASSIGNMENT (( #74352 ) ) ; +#11964 = EDGE_CURVE ( 'NONE', #1722, #73267, #80608, .T. ) ; +#11967 = AXIS2_PLACEMENT_3D ( 'NONE', #52870, #43179, #90141 ) ; +#11966 = STYLED_ITEM ( 'NONE', ( #38131 ), #38206 ) ; +#11965 = LINE ( 'NONE', #84499, #8798 ) ; +#11968 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.000000000000000000 ) ) ; +#11969 = LINE ( 'NONE', #89171, #48488 ) ; +#11970 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11971 = EDGE_CURVE ( 'NONE', #37213, #10900, #64524, .T. ) ; +#11972 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#11973 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63261 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50385, #3384, #81006 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11974 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40813, #48978, #87761, #95385 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#11975 = SURFACE_STYLE_FILL_AREA ( #35581 ) ; +#11976 = VECTOR ( 'NONE', #41625, 1000.000000000000000 ) ; +#11977 = SURFACE_STYLE_FILL_AREA ( #3419 ) ; +#11978 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#11979 = CARTESIAN_POINT ( 'NONE', ( -1.303800513451622844, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#11980 = FACE_OUTER_BOUND ( 'NONE', #34184, .T. ) ; +#11981 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.4245906043549200204, 0.1900000000000000577 ) ) ; +#11982 = MANIFOLD_SOLID_BREP ( 'ÊäÈë120', #77920 ) ; +#11983 = CARTESIAN_POINT ( 'NONE', ( -0.1381505133853420109, 2.561284075926970161, 0.8100000000000000533 ) ) ; +#11984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92381 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65878, #19398, #50577 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#11985 = DIRECTION ( 'NONE', ( 0.2490410398106700784, 0.9684929325968364422, 0.000000000000000000 ) ) ; +#11986 = PLANE ( 'NONE', #72313 ) ; +#11987 = AXIS2_PLACEMENT_3D ( 'NONE', #34020, #49844, #71281 ) ; +#11988 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999989875, 0.000000000000000000 ) ) ; +#11989 = PLANE ( 'NONE', #30379 ) ; +#11990 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#11991 = ORIENTED_EDGE ( 'NONE', *, *, #22530, .T. ) ; +#11992 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#11993 = EDGE_CURVE ( 'NONE', #64904, #71293, #48212, .T. ) ; +#11994 = AXIS2_PLACEMENT_3D ( 'NONE', #43488, #90964, #90454 ) ; +#11996 = CARTESIAN_POINT ( 'NONE', ( -1.323820061220085220, -3.099999999999990319, -0.02000000000000000042 ) ) ; +#11995 = SURFACE_STYLE_FILL_AREA ( #50918 ) ; +#11997 = AXIS2_PLACEMENT_3D ( 'NONE', #92700, #46237, #100770 ) ; +#11998 = LINE ( 'NONE', #64210, #96605 ) ; +#11999 = EDGE_CURVE ( 'NONE', #23574, #59846, #95625, .T. ) ; +#12000 = ORIENTED_EDGE ( 'NONE', *, *, #23279, .F. ) ; +#12001 = SURFACE_SIDE_STYLE ('',( #75378 ) ) ; +#12003 = EDGE_CURVE ( 'NONE', #92486, #83675, #35908, .T. ) ; +#12002 = FILL_AREA_STYLE_COLOUR ( '', #70135 ) ; +#12004 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12005 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12006 = SURFACE_STYLE_FILL_AREA ( #50930 ) ; +#12007 = VECTOR ( 'NONE', #16851, 1000.000000000000000 ) ; +#12008 = SURFACE_STYLE_FILL_AREA ( #5891 ) ; +#12009 = ORIENTED_EDGE ( 'NONE', *, *, #71629, .F. ) ; +#12010 = ORIENTED_EDGE ( 'NONE', *, *, #48849, .T. ) ; +#12011 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12012 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12013 = CARTESIAN_POINT ( 'NONE', ( 10.05860100000000124, 12.65647100000000158, 0.8991599999999999593 ) ) ; +#12014 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12015 = ORIENTED_EDGE ( 'NONE', *, *, #41181, .F. ) ; +#12016 = CARTESIAN_POINT ( 'NONE', ( 1.702517484154870031, -1.219598171061480052, 0.8299999999999999600 ) ) ; +#12017 = SURFACE_STYLE_USAGE ( .BOTH. , #65225 ) ; +#12018 = VECTOR ( 'NONE', #32694, 1000.000000000000000 ) ; +#12019 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12020 = FILL_AREA_STYLE_COLOUR ( '', #23696 ) ; +#12021 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#12022 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #46966, #82894 ) ; +#12023 = FACE_OUTER_BOUND ( 'NONE', #65872, .T. ) ; +#12024 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12027 = VERTEX_POINT ( 'NONE', #81868 ) ; +#12026 = ORIENTED_EDGE ( 'NONE', *, *, #1903, .T. ) ; +#12025 = ADVANCED_FACE ( 'NONE', ( #21074 ), #51726, .T. ) ; +#12028 = VECTOR ( 'NONE', #95829, 1000.000000000000000 ) ; +#12029 = ORIENTED_EDGE ( 'NONE', *, *, #18337, .F. ) ; +#12030 = EDGE_LOOP ( 'NONE', ( #4317, #38027, #41871, #89218, #30280, #29603 ) ) ; +#12031 = FACE_OUTER_BOUND ( 'NONE', #92368, .T. ) ; +#12032 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12034 = STYLED_ITEM ( 'NONE', ( #35705 ), #19920 ) ; +#12033 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37913, 'distance_accuracy_value', 'NONE'); +#12035 = CARTESIAN_POINT ( 'NONE', ( 1.876343683457829981, -1.423344911062679907, 0.8100000000000000533 ) ) ; +#12037 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1458578643762690752 ) ) ; +#12036 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#12038 = ORIENTED_EDGE ( 'NONE', *, *, #73765, .F. ) ; +#12039 = EDGE_CURVE ( 'NONE', #92928, #75277, #16509, .T. ) ; +#12040 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#12041 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12042 = CARTESIAN_POINT ( 'NONE', ( -2.523820061220085176, 3.100000000000000089, 0.000000000000000000 ) ) ; +#12043 = ORIENTED_EDGE ( 'NONE', *, *, #41922, .T. ) ; +#12044 = EDGE_CURVE ( 'NONE', #74817, #89369, #11800, .T. ) ; +#12046 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12045 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#12047 = ORIENTED_EDGE ( 'NONE', *, *, #35091, .T. ) ; +#12048 = VERTEX_POINT ( 'NONE', #43531 ) ; +#12049 = SURFACE_STYLE_FILL_AREA ( #82105 ) ; +#12051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12050 = PRESENTATION_STYLE_ASSIGNMENT (( #59149 ) ) ; +#12052 = CARTESIAN_POINT ( 'NONE', ( 1.886527894060100019, -1.258231835375339891, 0.8300000000000004041 ) ) ; +#12054 = EDGE_CURVE ( 'NONE', #2319, #79066, #98095, .T. ) ; +#12053 = LINE ( 'NONE', #72927, #92921 ) ; +#12055 = ORIENTED_EDGE ( 'NONE', *, *, #83171, .T. ) ; +#12056 = VECTOR ( 'NONE', #98806, 1000.000000000000000 ) ; +#12057 = SURFACE_STYLE_USAGE ( .BOTH. , #82606 ) ; +#12058 = VERTEX_POINT ( 'NONE', #66027 ) ; +#12059 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12060 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12061 = PRESENTATION_STYLE_ASSIGNMENT (( #89744 ) ) ; +#12062 = ORIENTED_EDGE ( 'NONE', *, *, #5742, .F. ) ; +#12064 = SURFACE_STYLE_USAGE ( .BOTH. , #82119 ) ; +#12063 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12065 = LINE ( 'NONE', #43287, #73835 ) ; +#12066 = ORIENTED_EDGE ( 'NONE', *, *, #38526, .F. ) ; +#12067 = EDGE_CURVE ( 'NONE', #97744, #89365, #75203, .T. ) ; +#12068 = ORIENTED_EDGE ( 'NONE', *, *, #44428, .F. ) ; +#12070 = PLANE ( 'NONE', #61825 ) ; +#12069 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#12071 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12072 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12073 = FILL_AREA_STYLE ('',( #28008 ) ) ; +#12074 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#12075 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52990 ) ) ; +#12076 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12077 = ADVANCED_FACE ( 'NONE', ( #34408 ), #65506, .T. ) ; +#12078 = EDGE_CURVE ( 'NONE', #91043, #60837, #92489, .T. ) ; +#12079 = PRESENTATION_STYLE_ASSIGNMENT (( #66293 ) ) ; +#12080 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100368, 'distance_accuracy_value', 'NONE'); +#12081 = ORIENTED_EDGE ( 'NONE', *, *, #52401, .F. ) ; +#12082 = PRESENTATION_STYLE_ASSIGNMENT (( #13591 ) ) ; +#12083 = ORIENTED_EDGE ( 'NONE', *, *, #66985, .F. ) ; +#12084 = STYLED_ITEM ( 'NONE', ( #92137 ), #71828 ) ; +#12085 = PLANE ( 'NONE', #29373 ) ; +#12086 = CARTESIAN_POINT ( 'NONE', ( -0.007896400202255349221, -1.058723197808659977, 0.8100000000000000533 ) ) ; +#12087 = ADVANCED_FACE ( 'NONE', ( #37898 ), #36893, .F. ) ; +#12088 = EDGE_CURVE ( 'NONE', #71649, #17922, #30704, .T. ) ; +#12090 = LINE ( 'NONE', #22854, #73141 ) ; +#12089 = AXIS2_PLACEMENT_3D ( 'NONE', #43340, #51549, #91797 ) ; +#12091 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12092 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12093 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#12094 = ORIENTED_EDGE ( 'NONE', *, *, #3969, .T. ) ; +#12095 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#12096 = SURFACE_STYLE_FILL_AREA ( #50517 ) ; +#12097 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12098 = EDGE_CURVE ( 'NONE', #84529, #17149, #84837, .T. ) ; +#12099 = CARTESIAN_POINT ( 'NONE', ( 0.1868680034464730022, -1.007635622941599918, 0.8299999999999999600 ) ) ; +#12100 = PRESENTATION_STYLE_ASSIGNMENT (( #19842 ) ) ; +#12101 = FACE_OUTER_BOUND ( 'NONE', #37648, .T. ) ; +#12102 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12103 = STYLED_ITEM ( 'NONE', ( #23392 ), #48309 ) ; +#12104 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12105 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25894, 'distance_accuracy_value', 'NONE'); +#12106 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#12108 = SURFACE_STYLE_USAGE ( .BOTH. , #59711 ) ; +#12107 = VECTOR ( 'NONE', #25952, 1000.000000000000000 ) ; +#12109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12110 = LINE ( 'NONE', #58689, #63424 ) ; +#12111 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691085, -0.01500000000000005322, 0.2458578643762690530 ) ) ; +#12112 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12113 = SURFACE_SIDE_STYLE ('',( #10582 ) ) ; +#12114 = AXIS2_PLACEMENT_3D ( 'NONE', #51896, #91182, #83032 ) ; +#12115 = ORIENTED_EDGE ( 'NONE', *, *, #92429, .F. ) ; +#12116 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12117 = CARTESIAN_POINT ( 'NONE', ( 1.572445103981990222, -0.9412361261466359874, 0.8299999999999999600 ) ) ; +#12118 = FILL_AREA_STYLE ('',( #66815 ) ) ; +#12119 = ORIENTED_EDGE ( 'NONE', *, *, #58038, .F. ) ; +#12120 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12121 = AXIS2_PLACEMENT_3D ( 'NONE', #47853, #9958, #47338 ) ; +#12122 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12123 = LINE ( 'NONE', #52037, #40691 ) ; +#12124 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12125 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#12126 = EDGE_LOOP ( 'NONE', ( #34973, #43252, #35293, #20299 ) ) ; +#12127 = VERTEX_POINT ( 'NONE', #22057 ) ; +#12128 = EDGE_CURVE ( 'NONE', #9989, #94767, #29716, .T. ) ; +#12129 = STYLED_ITEM ( 'NONE', ( #93077 ), #3545 ) ; +#12130 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.783333333333333437, 0.000000000000000000 ) ) ; +#12131 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12132 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8099999999999885070 ) ) ; +#12133 = CIRCLE ( 'NONE', #35061, 0.04999999999999999584 ) ; +#12134 = FILL_AREA_STYLE ('',( #37230 ) ) ; +#12135 = FILL_AREA_STYLE_COLOUR ( '', #59974 ) ; +#12136 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12137 = CARTESIAN_POINT ( 'NONE', ( -1.226541225640779498, -0.8904278853685345663, 0.8100000000000687761 ) ) ; +#12138 = EDGE_CURVE ( 'NONE', #83308, #88616, #12133, .T. ) ; +#12139 = PRESENTATION_STYLE_ASSIGNMENT (( #97930 ) ) ; +#12140 = FACE_OUTER_BOUND ( 'NONE', #45603, .T. ) ; +#12141 = EDGE_LOOP ( 'NONE', ( #20556, #64251, #45451, #73632 ) ) ; +#12142 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2469 ) ) ; +#12143 = PLANE ( 'NONE', #97616 ) ; +#12144 = EDGE_LOOP ( 'NONE', ( #30407, #78792, #82367, #27251 ) ) ; +#12145 = FILL_AREA_STYLE_COLOUR ( '', #10933 ) ; +#12146 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#12147 = FILL_AREA_STYLE ('',( #5535 ) ) ; +#12148 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12149 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12150 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43203 ), #77446 ) ; +#12154 = ORIENTED_EDGE ( 'NONE', *, *, #34808, .F. ) ; +#12153 = ORIENTED_EDGE ( 'NONE', *, *, #58363, .T. ) ; +#12152 = ADVANCED_FACE ( 'NONE', ( #76186 ), #37415, .F. ) ; +#12151 = VECTOR ( 'NONE', #45647, 1000.000000000000000 ) ; +#12155 = MANIFOLD_SOLID_BREP ( 'ÊäÈë36', #28946 ) ; +#12156 = VERTEX_POINT ( 'NONE', #16892 ) ; +#12157 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.3000000000000020428, 0.1829999999999709359 ) ) ; +#12158 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12160 = CARTESIAN_POINT ( 'NONE', ( 4.281867249749913285, 4.984284750250088436, 0.8991599999999999593 ) ) ; +#12159 = FILL_AREA_STYLE ('',( #13677 ) ) ; +#12161 = ORIENTED_EDGE ( 'NONE', *, *, #72809, .T. ) ; +#12163 = EDGE_CURVE ( 'NONE', #22278, #13170, #86366, .T. ) ; +#12162 = ORIENTED_EDGE ( 'NONE', *, *, #47551, .T. ) ; +#12164 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96980 ) ) ; +#12166 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12167 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#12168 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.299999999999999822, -1.507334416018511324E-89 ) ) ; +#12169 = ORIENTED_EDGE ( 'NONE', *, *, #5894, .F. ) ; +#12170 = ORIENTED_EDGE ( 'NONE', *, *, #32197, .T. ) ; +#12171 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12172 = STYLED_ITEM ( 'NONE', ( #72253 ), #48704 ) ; +#12173 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49748 ) ) ; +#12174 = ORIENTED_EDGE ( 'NONE', *, *, #51955, .T. ) ; +#12175 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#12176 = STYLED_ITEM ( 'NONE', ( #67963 ), #77147 ) ; +#12177 = EDGE_LOOP ( 'NONE', ( #26252, #25195, #48629, #33363 ) ) ; +#12178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98538 ) ) ; +#12179 = LINE ( 'NONE', #89866, #53760 ) ; +#12180 = ORIENTED_EDGE ( 'NONE', *, *, #92949, .T. ) ; +#12182 = LINE ( 'NONE', #11666, #25705 ) ; +#12181 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90779 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46070, #92063, #67566 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12183 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12184 = ORIENTED_EDGE ( 'NONE', *, *, #17225, .F. ) ; +#12185 = EDGE_CURVE ( 'NONE', #62672, #3964, #57266, .T. ) ; +#12186 = EDGE_LOOP ( 'NONE', ( #58709, #75388, #33885, #6756 ) ) ; +#12187 = SURFACE_STYLE_USAGE ( .BOTH. , #74060 ) ; +#12188 = LINE ( 'NONE', #4111, #64422 ) ; +#12189 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70170 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61660, #93730, #45760 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12190 = SURFACE_SIDE_STYLE ('',( #51106 ) ) ; +#12191 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87266 ), #95323 ) ; +#12192 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#12193 = LINE ( 'NONE', #66892, #85688 ) ; +#12194 = SURFACE_SIDE_STYLE ('',( #5081 ) ) ; +#12195 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88889 ) ) ; +#12196 = LINE ( 'NONE', #50612, #24810 ) ; +#12197 = FILL_AREA_STYLE ('',( #67395 ) ) ; +#12199 = PRESENTATION_STYLE_ASSIGNMENT (( #58783 ) ) ; +#12198 = SURFACE_STYLE_FILL_AREA ( #75089 ) ; +#12200 = CARTESIAN_POINT ( 'NONE', ( 1.572445103981990222, -0.9412361261466359874, 0.8299999999999997380 ) ) ; +#12201 = VERTEX_POINT ( 'NONE', #25129 ) ; +#12202 = FACE_OUTER_BOUND ( 'NONE', #80828, .T. ) ; +#12203 = CARTESIAN_POINT ( 'NONE', ( -0.9327878365278901018, -1.419416888468929994, 0.8299999999999999600 ) ) ; +#12204 = ORIENTED_EDGE ( 'NONE', *, *, #58278, .T. ) ; +#12205 = STYLED_ITEM ( 'NONE', ( #561 ), #3806 ) ; +#12206 = EDGE_CURVE ( 'NONE', #56849, #15082, #579, .T. ) ; +#12207 = CARTESIAN_POINT ( 'NONE', ( -0.1344673260136140247, -1.507258815139120189, 0.8299999999999999600 ) ) ; +#12209 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62111 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49336, #33010, #24883 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12208 = CARTESIAN_POINT ( 'NONE', ( -0.4538159765161179915, -1.241081418093670008, 0.8300000000000000711 ) ) ; +#12210 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ipx3.STEP', ( #12501, #61587 ), #25643 ) ; +#12211 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2850000000000020850, 0.1458578643762672711 ) ) ; +#12212 = SURFACE_STYLE_FILL_AREA ( #97990 ) ; +#12213 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12214 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12215 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#12216 = EDGE_CURVE ( 'NONE', #32462, #11153, #96809, .T. ) ; +#12217 = PLANE ( 'NONE', #70510 ) ; +#12218 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12219 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87294 ) ) ; +#12220 = PLANE ( 'NONE', #12301 ) ; +#12221 = EDGE_CURVE ( 'NONE', #38363, #64015, #2121, .T. ) ; +#12222 = ORIENTED_EDGE ( 'NONE', *, *, #93244, .T. ) ; +#12223 = PLANE ( 'NONE', #94454 ) ; +#12224 = STYLED_ITEM ( 'NONE', ( #14224 ), #29790 ) ; +#12226 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.291173436397889936E-79, 4.640777529015779698E-48 ) ) ; +#12225 = FACE_OUTER_BOUND ( 'NONE', #1501, .T. ) ; +#12227 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69591 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21121, #84897, #13379 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12228 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92241 ), #49874 ) ; +#12229 = ORIENTED_EDGE ( 'NONE', *, *, #85284, .F. ) ; +#12230 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#12231 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88923 ), #53067 ) ; +#12232 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#12233 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#12234 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12235 = STYLED_ITEM ( 'NONE', ( #65421 ), #89244 ) ; +#12236 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, -3.099999999999969891, 0.000000000000000000 ) ) ; +#12237 = VECTOR ( 'NONE', #1978, 1000.000000000000000 ) ; +#12238 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12239 = AXIS2_PLACEMENT_3D ( 'NONE', #10, #92906, #93416 ) ; +#12240 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.36999999999999922 ) ) ; +#12241 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #11140, #50570 ), + ( #19895, #29070 ), + ( #44355, #89839 ), + ( #43375, #20898 ), + ( #12671, #36732 ), + ( #27578, #76025 ), + ( #51067, #52065 ), + ( #66855, #58738 ), + ( #75522, #5538 ), + ( #37248, #13670 ), + ( #75044, #67837 ), + ( #43874, #20385 ), + ( #98419, #98916 ), + ( #91347, #28555 ), + ( #60243, #6015 ), + ( #74544, #82204 ), + ( #66367, #52558 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07368751262769830668, 0.1417920735975989888, 0.2054115302518020048, 0.2658518701935390083, 0.3244427805873369985, 0.3816258437036210149, 0.4386397466422020108, 0.4960160260038000146, 0.5547989483227619978, 0.6144450223394879451, 0.6760330661510820516, 0.7394243817737230495, 0.8697955919226270094, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#12242 = CIRCLE ( 'NONE', #25410, 0.5300000000829642177 ) ; +#12243 = VERTEX_POINT ( 'NONE', #16376 ) ; +#12244 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12245 = ORIENTED_EDGE ( 'NONE', *, *, #32602, .F. ) ; +#12246 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40980, 'distance_accuracy_value', 'NONE'); +#12247 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89419, 'distance_accuracy_value', 'NONE'); +#12248 = SURFACE_STYLE_USAGE ( .BOTH. , #99505 ) ; +#12249 = PRESENTATION_STYLE_ASSIGNMENT (( #75137 ) ) ; +#12250 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12251 = PLANE ( 'NONE', #47781 ) ; +#12252 = CYLINDRICAL_SURFACE ( 'NONE', #78270, 0.009999999999999998473 ) ; +#12253 = SURFACE_SIDE_STYLE ('',( #12764 ) ) ; +#12254 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.266666666666647068, 0.000000000000000000 ) ) ; +#12255 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85918, #47113, #31798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12257 = EDGE_CURVE ( 'NONE', #91350, #86759, #96009, .T. ) ; +#12258 = ORIENTED_EDGE ( 'NONE', *, *, #99814, .F. ) ; +#12259 = SURFACE_SIDE_STYLE ('',( #82312 ) ) ; +#12261 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#12260 = SURFACE_STYLE_USAGE ( .BOTH. , #4669 ) ; +#12262 = ORIENTED_EDGE ( 'NONE', *, *, #9608, .T. ) ; +#12263 = FILL_AREA_STYLE_COLOUR ( '', #52375 ) ; +#12264 = CIRCLE ( 'NONE', #43318, 1.200947669413299890 ) ; +#12265 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1399999999999999856 ) ) ; +#12266 = VERTEX_POINT ( 'NONE', #24104 ) ; +#12267 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10656 ), #51533 ) ; +#12268 = PRESENTATION_STYLE_ASSIGNMENT (( #99522 ) ) ; +#12269 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12270 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12271 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12272 = FACE_OUTER_BOUND ( 'NONE', #510, .T. ) ; +#12273 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12274 = ORIENTED_EDGE ( 'NONE', *, *, #59129, .T. ) ; +#12275 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100344 ) ) ; +#12276 = LINE ( 'NONE', #98052, #97881 ) ; +#12277 = FACE_OUTER_BOUND ( 'NONE', #2561, .T. ) ; +#12278 = VERTEX_POINT ( 'NONE', #78696 ) ; +#12279 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12280 = ORIENTED_EDGE ( 'NONE', *, *, #57209, .T. ) ; +#12282 = EDGE_CURVE ( 'NONE', #33372, #30261, #8659, .T. ) ; +#12281 = EDGE_LOOP ( 'NONE', ( #87252, #3817, #83971, #18644 ) ) ; +#12283 = SURFACE_SIDE_STYLE ('',( #82333 ) ) ; +#12284 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333323090, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#12285 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12286 = FILL_AREA_STYLE ('',( #18512 ) ) ; +#12287 = VERTEX_POINT ( 'NONE', #82735 ) ; +#12288 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #87283, #82894 ), #79436 ) ; +#12290 = ORIENTED_EDGE ( 'NONE', *, *, #15931, .F. ) ; +#12289 = STYLED_ITEM ( 'NONE', ( #44524 ), #73412 ) ; +#12291 = VERTEX_POINT ( 'NONE', #97979 ) ; +#12292 = PRESENTATION_STYLE_ASSIGNMENT (( #27224 ) ) ; +#12293 = AXIS2_PLACEMENT_3D ( 'NONE', #51989, #98835, #51498 ) ; +#12294 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#12295 = ORIENTED_EDGE ( 'NONE', *, *, #4371, .F. ) ; +#12296 = EDGE_LOOP ( 'NONE', ( #54998, #83228, #33240, #91687 ) ) ; +#12297 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26932 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70782, #47814, #14606 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12298 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 4.142826999999999593, 0.8648700000000000276 ) ) ; +#12299 = STYLED_ITEM ( 'NONE', ( #23524 ), #90163 ) ; +#12300 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#12301 = AXIS2_PLACEMENT_3D ( 'NONE', #44911, #22992, #100450 ) ; +#12302 = FACE_OUTER_BOUND ( 'NONE', #51369, .T. ) ; +#12303 = EDGE_LOOP ( 'NONE', ( #15327, #19029, #92018, #55791 ) ) ; +#12304 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8100000000001210676 ) ) ; +#12305 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#12306 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12307 = EDGE_LOOP ( 'NONE', ( #97363, #63159, #33957, #77291 ) ) ; +#12308 = EDGE_CURVE ( 'NONE', #47287, #28432, #28601, .T. ) ; +#12309 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#12310 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100306 ), #20540 ) ; +#12311 = LINE ( 'NONE', #50236, #95281 ) ; +#12312 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12313 = FILL_AREA_STYLE ('',( #20545 ) ) ; +#12315 = SURFACE_STYLE_FILL_AREA ( #50729 ) ; +#12314 = VECTOR ( 'NONE', #81619, 1000.000000000000000 ) ; +#12316 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99135 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69847, #100866, #92331 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12317 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#12318 = CARTESIAN_POINT ( 'NONE', ( 1.697893922398610034, -1.445363849546990043, 0.8100000000000000533 ) ) ; +#12319 = SURFACE_STYLE_FILL_AREA ( #4725 ) ; +#12320 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12321 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12322 = MANIFOLD_SOLID_BREP ( 'ÊäÈë41', #73058 ) ; +#12323 = ORIENTED_EDGE ( 'NONE', *, *, #68621, .F. ) ; +#12324 = EDGE_CURVE ( 'NONE', #14320, #1547, #96955, .T. ) ; +#12325 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.000000000000000000 ) ) ; +#12326 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12327 = CARTESIAN_POINT ( 'NONE', ( 1.133718228224829927, -1.135808780994409961, 0.8300000000000022915 ) ) ; +#12328 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12329 = FILL_AREA_STYLE ('',( #84365 ) ) ; +#12330 = FILL_AREA_STYLE ('',( #58917 ) ) ; +#12331 = SURFACE_STYLE_USAGE ( .BOTH. , #81881 ) ; +#12332 = AXIS2_PLACEMENT_3D ( 'NONE', #7520, #38755, #100898 ) ; +#12333 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35782, #74569, #75074, #66882 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#12334 = STYLED_ITEM ( 'NONE', ( #51661 ), #99431 ) ; +#12335 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12336 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01499999999999998383, 0.1400000000000000133 ) ) ; +#12337 = ORIENTED_EDGE ( 'NONE', *, *, #35597, .F. ) ; +#12338 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23886 ) ) ; +#12339 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12340 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#12341 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12342 = CIRCLE ( 'NONE', #18967, 0.01000000000000002623 ) ; +#12343 = ORIENTED_EDGE ( 'NONE', *, *, #48140, .F. ) ; +#12344 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12346 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#12345 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#12347 = VECTOR ( 'NONE', #79977, 1000.000000000000000 ) ; +#12348 = PLANE ( 'NONE', #53484 ) ; +#12349 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12350 = STYLED_ITEM ( 'NONE', ( #3937 ), #12837 ) ; +#12351 = ORIENTED_EDGE ( 'NONE', *, *, #2442, .T. ) ; +#12352 = CARTESIAN_POINT ( 'NONE', ( 1.984465819873851400, 1.600000000000000089, -11.38547005383792055 ) ) ; +#12353 = SURFACE_STYLE_FILL_AREA ( #22095 ) ; +#12354 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#12355 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12356 = CARTESIAN_POINT ( 'NONE', ( 1.157135261321870168, -0.8867570690059840555, 0.8299999999999994049 ) ) ; +#12357 = CARTESIAN_POINT ( 'NONE', ( 1.182009071931110045, -1.515071875619850017, 0.8300000000000010703 ) ) ; +#12358 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12359 = FILL_AREA_STYLE_COLOUR ( '', #62881 ) ; +#12360 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12361 = VECTOR ( 'NONE', #11691, 1000.000000000000000 ) ; +#12362 = CARTESIAN_POINT ( 'NONE', ( 4.171940353495651044E-17, 0.2499999999940882844, 0.2299999999877400114 ) ) ; +#12363 = FILL_AREA_STYLE_COLOUR ( '', #15276 ) ; +#12364 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #118, 'distance_accuracy_value', 'NONE'); +#12365 = LINE ( 'NONE', #27286, #68057 ) ; +#12366 = EDGE_LOOP ( 'NONE', ( #23587, #19769, #42745, #29193 ) ) ; +#12367 = LINE ( 'NONE', #13896, #39966 ) ; +#12368 = ORIENTED_EDGE ( 'NONE', *, *, #22574, .T. ) ; +#12369 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12370 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56863, 'distance_accuracy_value', 'NONE'); +#12371 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23638, 'distance_accuracy_value', 'NONE'); +#12372 = CARTESIAN_POINT ( 'NONE', ( 1.186064574101910019, -0.9547617453595670378, 0.8100000000000000533 ) ) ; +#12373 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999856 ) ) ; +#12374 = FILL_AREA_STYLE_COLOUR ( '', #2483 ) ; +#12375 = CARTESIAN_POINT ( 'NONE', ( -1.359164620693936953, -1.424266694256196786, 0.8099999999996756461 ) ) ; +#12376 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54898 ) ) ; +#12377 = FILL_AREA_STYLE ('',( #58472 ) ) ; +#12378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12379 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.000000000000000000 ) ) ; +#12380 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#12381 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8648700000000000276 ) ) ; +#12382 = EDGE_CURVE ( 'NONE', #86354, #52415, #19942, .T. ) ; +#12383 = ORIENTED_EDGE ( 'NONE', *, *, #4778, .F. ) ; +#12385 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12384 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56525 ) ) ; +#12386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12387 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91532, 'distance_accuracy_value', 'NONE'); +#12388 = FILL_AREA_STYLE ('',( #59487 ) ) ; +#12389 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12390 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38560 ) ) ; +#12391 = ORIENTED_EDGE ( 'NONE', *, *, #69517, .F. ) ; +#12392 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12393 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12394 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12395 = STYLED_ITEM ( 'NONE', ( #21839 ), #62059 ) ; +#12396 = ORIENTED_EDGE ( 'NONE', *, *, #74981, .F. ) ; +#12397 = SURFACE_STYLE_FILL_AREA ( #44594 ) ; +#12398 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31635, 'distance_accuracy_value', 'NONE'); +#12399 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12400 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12401 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#12403 = EDGE_CURVE ( 'NONE', #34886, #21114, #66459, .T. ) ; +#12402 = ORIENTED_EDGE ( 'NONE', *, *, #68674, .F. ) ; +#12404 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12405 = SURFACE_SIDE_STYLE ('',( #45580 ) ) ; +#12406 = SURFACE_STYLE_USAGE ( .BOTH. , #27323 ) ; +#12407 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12408 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12409 = ORIENTED_EDGE ( 'NONE', *, *, #28445, .F. ) ; +#12410 = LINE ( 'NONE', #43615, #69331 ) ; +#12411 = ADVANCED_FACE ( 'NONE', ( #90380 ), #20433, .T. ) ; +#12412 = AXIS2_PLACEMENT_3D ( 'NONE', #24939, #25430, #4414 ) ; +#12413 = EDGE_CURVE ( 'NONE', #85879, #48033, #65384, .T. ) ; +#12414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12760 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93329, #16229, #74299 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12415 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12416 = ORIENTED_EDGE ( 'NONE', *, *, #100525, .T. ) ; +#12418 = VERTEX_POINT ( 'NONE', #57782 ) ; +#12417 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.500000000000000000, 0.1829999999999580018 ) ) ; +#12419 = SURFACE_STYLE_FILL_AREA ( #82467 ) ; +#12421 = CARTESIAN_POINT ( 'NONE', ( -1.364612412596039936, -1.414598001867640065, 0.8299999999999999600 ) ) ; +#12420 = FILL_AREA_STYLE_COLOUR ( '', #59133 ) ; +#12422 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12423 = PRESENTATION_STYLE_ASSIGNMENT (( #90099 ) ) ; +#12424 = CARTESIAN_POINT ( 'NONE', ( 6.954730750249974669, 2.311420750249975953, 0.8991599999999999593 ) ) ; +#12425 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#12426 = SURFACE_SIDE_STYLE ('',( #67604 ) ) ; +#12427 = EDGE_LOOP ( 'NONE', ( #6518, #79715, #99177, #48945 ) ) ; +#12428 = EDGE_CURVE ( 'NONE', #81228, #75115, #88892, .T. ) ; +#12429 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12430 = EDGE_CURVE ( 'NONE', #77419, #84686, #91881, .T. ) ; +#12431 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12432 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#12433 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60684 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57090, #56067, #88214 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12434 = EDGE_LOOP ( 'NONE', ( #62584, #82077, #88119, #6276 ) ) ; +#12435 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12436 = ORIENTED_EDGE ( 'NONE', *, *, #53694, .F. ) ; +#12438 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000311, -0.02000000000000839995 ) ) ; +#12437 = SURFACE_STYLE_FILL_AREA ( #82485 ) ; +#12439 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89202 ), #38607 ) ; +#12440 = LINE ( 'NONE', #28350, #32642 ) ; +#12441 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12442 = ORIENTED_EDGE ( 'NONE', *, *, #65113, .F. ) ; +#12443 = CARTESIAN_POINT ( 'NONE', ( -3.376791256618512612E-17, 0.8200000000000000622, 0.1378679656440357226 ) ) ; +#12444 = ORIENTED_EDGE ( 'NONE', *, *, #25911, .T. ) ; +#12445 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12447 = CARTESIAN_POINT ( 'NONE', ( 1.071224486614657412, 1.221896575926968875, 0.8299999999999999600 ) ) ; +#12446 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -13.35000000000000142 ) ) ; +#12448 = FILL_AREA_STYLE ('',( #37031 ) ) ; +#12449 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#12450 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15550 ), #82443 ) ; +#12451 = PRESENTATION_STYLE_ASSIGNMENT (( #28849 ) ) ; +#12452 = VECTOR ( 'NONE', #45621, 1000.000000000000000 ) ; +#12453 = LINE ( 'NONE', #36541, #97884 ) ; +#12454 = LINE ( 'NONE', #20695, #44267 ) ; +#12455 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#12456 = CARTESIAN_POINT ( 'NONE', ( 1.251030810655360037, -0.9616422087329199453, 0.8299999999999999600 ) ) ; +#12457 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54048, #85682, #84677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12458 = VERTEX_POINT ( 'NONE', #83744 ) ; +#12459 = FILL_AREA_STYLE ('',( #38041 ) ) ; +#12460 = EDGE_CURVE ( 'NONE', #84475, #34472, #9044, .T. ) ; +#12462 = SURFACE_SIDE_STYLE ('',( #97761 ) ) ; +#12461 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#12463 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#12464 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12465 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54364 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6120, #22501, #44459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12466 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12467 = SURFACE_SIDE_STYLE ('',( #51381 ) ) ; +#12468 = ORIENTED_EDGE ( 'NONE', *, *, #75795, .F. ) ; +#12469 = SURFACE_STYLE_FILL_AREA ( #96287 ) ; +#12470 = VECTOR ( 'NONE', #35683, 1000.000000000000000 ) ; +#12471 = VECTOR ( 'NONE', #31282, 1000.000000000000000 ) ; +#12472 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#12473 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.6999999999999990674, 0.000000000000000000 ) ) ; +#12474 = CARTESIAN_POINT ( 'NONE', ( 0.3504973566725850254, -1.231551917075010216, 0.8300000000000015143 ) ) ; +#12475 = SURFACE_STYLE_FILL_AREA ( #20720 ) ; +#12476 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.323820061220084998, -0.02000000000000000042 ) ) ; +#12477 = FILL_AREA_STYLE_COLOUR ( '', #15785 ) ; +#12478 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#12479 = DIRECTION ( 'NONE', ( -0.9990832187810425591, -0.04281030191567540555, 0.000000000000000000 ) ) ; +#12480 = EDGE_CURVE ( 'NONE', #79030, #79108, #21941, .T. ) ; +#12481 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12482 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#12483 = FILL_AREA_STYLE_COLOUR ( '', #60105 ) ; +#12484 = MANIFOLD_SOLID_BREP ( 'ÊäÈë124', #10793 ) ; +#12486 = CYLINDRICAL_SURFACE ( 'NONE', #66921, 0.05000000000000012768 ) ; +#12485 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96565 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83334, #87343, #79191 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12487 = SURFACE_STYLE_USAGE ( .BOTH. , #43703 ) ; +#12488 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97790, 'distance_accuracy_value', 'NONE'); +#12489 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12490 = LINE ( 'NONE', #43706, #3055 ) ; +#12491 = CARTESIAN_POINT ( 'NONE', ( -0.2677310921211660810, -0.9808836469697851390, 0.8300000000000009592 ) ) ; +#12492 = FILL_AREA_STYLE ('',( #4892 ) ) ; +#12493 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12494 = EDGE_CURVE ( 'NONE', #62901, #21886, #65193, .T. ) ; +#12495 = ORIENTED_EDGE ( 'NONE', *, *, #24083, .T. ) ; +#12496 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.399999999999999911, 0.000000000000000000 ) ) ; +#12497 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#12498 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26395, 'distance_accuracy_value', 'NONE'); +#12499 = SURFACE_SIDE_STYLE ('',( #52407 ) ) ; +#12500 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52966, 'distance_accuracy_value', 'NONE'); +#12501 = AXIS2_PLACEMENT_3D ( 'NONE', #64477, #50191, #11256 ) ; +#12503 = LINE ( 'NONE', #44217, #60111 ) ; +#12502 = PLANE ( 'NONE', #15015 ) ; +#12504 = EDGE_CURVE ( 'NONE', #53924, #63952, #99936, .T. ) ; +#12505 = CIRCLE ( 'NONE', #22414, 0.2000000000000005107 ) ; +#12506 = CARTESIAN_POINT ( 'NONE', ( -0.7666666666666723806, -3.500000000000000000, 0.000000000000000000 ) ) ; +#12507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12508 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12509 = VECTOR ( 'NONE', #53002, 1000.000000000000000 ) ; +#12510 = VERTEX_POINT ( 'NONE', #44399 ) ; +#12511 = PRESENTATION_STYLE_ASSIGNMENT (( #82556 ) ) ; +#12513 = ADVANCED_FACE ( 'NONE', ( #38774 ), #37295, .T. ) ; +#12512 = PRESENTATION_STYLE_ASSIGNMENT (( #44712 ) ) ; +#12514 = VERTEX_POINT ( 'NONE', #75571 ) ; +#12515 = FACE_OUTER_BOUND ( 'NONE', #19829, .T. ) ; +#12516 = PRESENTATION_STYLE_ASSIGNMENT (( #51431 ) ) ; +#12517 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84764, 'distance_accuracy_value', 'NONE'); +#12519 = CARTESIAN_POINT ( 'NONE', ( 3.560618875125044269, 6.822762875125043536, 0.8991599999999999593 ) ) ; +#12518 = STYLED_ITEM ( 'NONE', ( #78130 ), #84006 ) ; +#12520 = AXIS2_PLACEMENT_3D ( 'NONE', #59069, #20207, #90149 ) ; +#12521 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99226, 'distance_accuracy_value', 'NONE'); +#12522 = SURFACE_STYLE_FILL_AREA ( #49040 ) ; +#12523 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12524 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90729 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96180, #72220, #72721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12525 = ORIENTED_EDGE ( 'NONE', *, *, #70720, .T. ) ; +#12526 = ORIENTED_EDGE ( 'NONE', *, *, #98752, .T. ) ; +#12527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12528 = ORIENTED_EDGE ( 'NONE', *, *, #46820, .F. ) ; +#12529 = CARTESIAN_POINT ( 'NONE', ( 0.2502762232558249922, -1.044215898305860035, 0.8299999999999996270 ) ) ; +#12530 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12531 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.6899999999999999467, 1.115425582119114573E-18 ) ) ; +#12532 = CARTESIAN_POINT ( 'NONE', ( 1.383333333333333526, -3.099999999999969891, 0.000000000000000000 ) ) ; +#12533 = EDGE_CURVE ( 'NONE', #3199, #27159, #5580, .T. ) ; +#12534 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#12535 = ADVANCED_FACE ( 'NONE', ( #57527 ), #88148, .T. ) ; +#12536 = SURFACE_STYLE_FILL_AREA ( #36623 ) ; +#12539 = VERTEX_POINT ( 'NONE', #40684 ) ; +#12538 = EDGE_LOOP ( 'NONE', ( #58319, #42788, #74320, #75285 ) ) ; +#12537 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #48029, #62355, #24585, #69977 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#12540 = VECTOR ( 'NONE', #15536, 1000.000000000000000 ) ; +#12541 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74585 ) ) ; +#12542 = ORIENTED_EDGE ( 'NONE', *, *, #21536, .F. ) ; +#12543 = ORIENTED_EDGE ( 'NONE', *, *, #14374, .T. ) ; +#12544 = FILL_AREA_STYLE_COLOUR ( '', #5112 ) ; +#12545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7086 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33443, #87046, #94162 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12546 = STYLED_ITEM ( 'NONE', ( #98651 ), #16226 ) ; +#12547 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#12548 = AXIS2_PLACEMENT_3D ( 'NONE', #40749, #71886, #2942 ) ; +#12550 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8648700000000000276 ) ) ; +#12549 = CARTESIAN_POINT ( 'NONE', ( 0.4642887493627290141, -0.9252028835730660150, 0.8299999999999999600 ) ) ; +#12551 = CLOSED_SHELL ( 'NONE', ( #94200, #44109, #32688, #45744, #50218, #29235 ) ) ; +#12552 = EDGE_CURVE ( 'NONE', #42723, #55806, #25377, .T. ) ; +#12554 = STYLED_ITEM ( 'NONE', ( #31384 ), #40091 ) ; +#12553 = SURFACE_STYLE_FILL_AREA ( #42772 ) ; +#12555 = CARTESIAN_POINT ( 'NONE', ( -0.1475413082135959286, -1.164854777894117177, 0.8100000000000000533 ) ) ; +#12556 = EDGE_CURVE ( 'NONE', #90736, #71596, #73336, .T. ) ; +#12557 = VERTEX_POINT ( 'NONE', #72822 ) ; +#12558 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30761 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77191, #78226, #45507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12559 = ADVANCED_FACE ( 'NONE', ( #26371 ), #17159, .F. ) ; +#12561 = FILL_AREA_STYLE ('',( #50476 ) ) ; +#12560 = SURFACE_STYLE_FILL_AREA ( #96359 ) ; +#12562 = ORIENTED_EDGE ( 'NONE', *, *, #44483, .F. ) ; +#12563 = ORIENTED_EDGE ( 'NONE', *, *, #19861, .T. ) ; +#12564 = CARTESIAN_POINT ( 'NONE', ( 1.086367759722999926, -1.195322104373920169, 0.8299999999999999600 ) ) ; +#12565 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55009 ) ) ; +#12566 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12567 = SURFACE_STYLE_FILL_AREA ( #75422 ) ; +#12568 = FACE_OUTER_BOUND ( 'NONE', #35053, .T. ) ; +#12570 = ORIENTED_EDGE ( 'NONE', *, *, #77010, .T. ) ; +#12569 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12571 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52164 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58199, #84149, #82168 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12572 = ORIENTED_EDGE ( 'NONE', *, *, #21988, .F. ) ; +#12573 = EDGE_CURVE ( 'NONE', #98494, #20186, #68584, .T. ) ; +#12574 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 7.544011000000000244, 0.8648700000000000276 ) ) ; +#12575 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#12576 = ORIENTED_EDGE ( 'NONE', *, *, #31328, .T. ) ; +#12577 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12578 = VERTEX_POINT ( 'NONE', #30270 ) ; +#12579 = ORIENTED_EDGE ( 'NONE', *, *, #29743, .T. ) ; +#12581 = SURFACE_STYLE_FILL_AREA ( #90257 ) ; +#12580 = FILL_AREA_STYLE_COLOUR ( '', #6425 ) ; +#12582 = FILL_AREA_STYLE_COLOUR ( '', #46526 ) ; +#12583 = ADVANCED_FACE ( 'NONE', ( #84425 ), #69586, .T. ) ; +#12584 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#12585 = FILL_AREA_STYLE ('',( #50498 ) ) ; +#12586 = VECTOR ( 'NONE', #39050, 1000.000000000000114 ) ; +#12587 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12588 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#12589 = EDGE_CURVE ( 'NONE', #33110, #71133, #21138, .T. ) ; +#12590 = STYLED_ITEM ( 'NONE', ( #45164 ), #31032 ) ; +#12591 = VERTEX_POINT ( 'NONE', #46081 ) ; +#12592 = VERTEX_POINT ( 'NONE', #92558 ) ; +#12593 = ADVANCED_FACE ( 'NONE', ( #22650 ), #36971, .T. ) ; +#12594 = CARTESIAN_POINT ( 'NONE', ( -0.1097768158302629971, -0.9623926821384259922, 0.8100000000000000533 ) ) ; +#12595 = CARTESIAN_POINT ( 'NONE', ( 1.352961788992439907, -1.196758459236680006, 0.8100000000000000533 ) ) ; +#12596 = CARTESIAN_POINT ( 'NONE', ( 3.794707603699269956E-16, 1.393372100993099938, 0.8100000000000000533 ) ) ; +#12597 = STYLED_ITEM ( 'NONE', ( #26415 ), #84420 ) ; +#12598 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12599 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000009992, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#12600 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, 0.09999999999999939493, -0.02000000000002519901 ) ) ; +#12601 = FACE_OUTER_BOUND ( 'NONE', #34249, .T. ) ; +#12602 = ORIENTED_EDGE ( 'NONE', *, *, #99984, .T. ) ; +#12603 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.500000000000000444, 0.000000000000000000 ) ) ; +#12604 = SURFACE_STYLE_USAGE ( .BOTH. , #82635 ) ; +#12605 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#12606 = PRESENTATION_STYLE_ASSIGNMENT (( #66312 ) ) ; +#12607 = SURFACE_STYLE_USAGE ( .BOTH. , #94141 ) ; +#12608 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12609 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21629 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88392, #18421, #17155 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12610 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8099999999998663824 ) ) ; +#12611 = CARTESIAN_POINT ( 'NONE', ( 1.897707761045830166, -1.292112914554750080, 0.8299999999999999600 ) ) ; +#12612 = LINE ( 'NONE', #26145, #83858 ) ; +#12613 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46340 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67738, #38136, #99315 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12614 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12615 = ADVANCED_FACE ( 'NONE', ( #29305 ), #91576, .T. ) ; +#12617 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73045 ), #20850 ) ; +#12616 = FILL_AREA_STYLE ('',( #28035 ) ) ; +#12618 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63308 ) ) ; +#12620 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.004999999999999996635, 0.2400000000000000466 ) ) ; +#12621 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#12622 = AXIS2_PLACEMENT_3D ( 'NONE', #25295, #24792, #48260 ) ; +#12623 = AXIS2_PLACEMENT_3D ( 'NONE', #73522, #17356, #35247 ) ; +#12624 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#12625 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49864, 'distance_accuracy_value', 'NONE'); +#12626 = EDGE_LOOP ( 'NONE', ( #27490, #18031, #67972, #53781, #68623, #72911 ) ) ; +#12627 = CLOSED_SHELL ( 'NONE', ( #81138, #4464, #11875, #36264, #92465, #83062 ) ) ; +#12628 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#12629 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#12631 = EDGE_CURVE ( 'NONE', #93277, #24062, #8249, .T. ) ; +#12630 = PRESENTATION_STYLE_ASSIGNMENT (( #18835 ) ) ; +#12632 = ORIENTED_EDGE ( 'NONE', *, *, #22355, .T. ) ; +#12633 = SURFACE_SIDE_STYLE ('',( #58702 ) ) ; +#12634 = VECTOR ( 'NONE', #15270, 1000.000000000000000 ) ; +#12635 = VECTOR ( 'NONE', #44338, 1000.000000000000000 ) ; +#12636 = PRESENTATION_STYLE_ASSIGNMENT (( #38448 ) ) ; +#12637 = ADVANCED_FACE ( 'NONE', ( #16453 ), #55335, .T. ) ; +#12638 = SURFACE_STYLE_USAGE ( .BOTH. , #59219 ) ; +#12639 = CARTESIAN_POINT ( 'NONE', ( -0.8073450731391820234, 0.5791240218592531575, 0.8299999999999999600 ) ) ; +#12640 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12641 = ORIENTED_EDGE ( 'NONE', *, *, #75351, .T. ) ; +#12642 = VECTOR ( 'NONE', #79732, 1000.000000000000000 ) ; +#12643 = ORIENTED_EDGE ( 'NONE', *, *, #84498, .T. ) ; +#12644 = PLANE ( 'NONE', #32475 ) ; +#12645 = EDGE_CURVE ( 'NONE', #80616, #100631, #23662, .T. ) ; +#12646 = FILL_AREA_STYLE ('',( #44334 ) ) ; +#12647 = FACE_OUTER_BOUND ( 'NONE', #53490, .T. ) ; +#12648 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12649 = FILL_AREA_STYLE ('',( #67329 ) ) ; +#12650 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57631, 'distance_accuracy_value', 'NONE'); +#12651 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12652 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#12653 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60830, 'distance_accuracy_value', 'NONE'); +#12654 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12655 = AXIS2_PLACEMENT_3D ( 'NONE', #31850, #2241, #63534 ) ; +#12656 = SURFACE_STYLE_USAGE ( .BOTH. , #99396 ) ; +#12657 = VERTEX_POINT ( 'NONE', #17481 ) ; +#12658 = ORIENTED_EDGE ( 'NONE', *, *, #60103, .T. ) ; +#12659 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6171 ) ) ; +#12660 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12661 = VERTEX_POINT ( 'NONE', #25203 ) ; +#12662 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12663 = STYLED_ITEM ( 'NONE', ( #68976 ), #74608 ) ; +#12664 = PRESENTATION_STYLE_ASSIGNMENT (( #66848 ) ) ; +#12665 = EDGE_CURVE ( 'NONE', #59034, #7959, #78775, .T. ) ; +#12666 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402590496, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#12667 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#12668 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14278 ) ) ; +#12669 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12670 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12671 = CARTESIAN_POINT ( 'NONE', ( -1.287544264014619966, -1.018544155089240011, 0.8100000000000000533 ) ) ; +#12672 = LINE ( 'NONE', #50890, #64400 ) ; +#12674 = EDGE_LOOP ( 'NONE', ( #5186, #3435, #89290, #71838 ) ) ; +#12673 = ORIENTED_EDGE ( 'NONE', *, *, #33135, .F. ) ; +#12675 = MANIFOLD_SOLID_BREP ( 'ÊäÈë35', #25688 ) ; +#12676 = VECTOR ( 'NONE', #91968, 1000.000000000000000 ) ; +#12677 = VERTEX_POINT ( 'NONE', #73149 ) ; +#12678 = SURFACE_STYLE_FILL_AREA ( #35759 ) ; +#12680 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#12679 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#12681 = ORIENTED_EDGE ( 'NONE', *, *, #74555, .F. ) ; +#12682 = AXIS2_PLACEMENT_3D ( 'NONE', #83159, #60210, #99856 ) ; +#12683 = EDGE_LOOP ( 'NONE', ( #4225, #6085, #89153, #60142 ) ) ; +#12684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12685 = PLANE ( 'NONE', #69163 ) ; +#12686 = EDGE_CURVE ( 'NONE', #71649, #36642, #43332, .T. ) ; +#12687 = LINE ( 'NONE', #28092, #66659 ) ; +#12688 = CIRCLE ( 'NONE', #89358, 0.05000000000000002359 ) ; +#12689 = ORIENTED_EDGE ( 'NONE', *, *, #23245, .F. ) ; +#12690 = EDGE_LOOP ( 'NONE', ( #54327, #10148, #65494, #33874 ) ) ; +#12691 = ADVANCED_FACE ( 'NONE', ( #74150 ), #6262, .T. ) ; +#12692 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#12693 = VERTEX_POINT ( 'NONE', #95576 ) ; +#12694 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12696 = VERTEX_POINT ( 'NONE', #57340 ) ; +#12695 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, 0.6500000000000000222 ) ) ; +#12697 = VECTOR ( 'NONE', #89924, 1000.000000000000000 ) ; +#12698 = SURFACE_SIDE_STYLE ('',( #68376 ) ) ; +#12699 = VECTOR ( 'NONE', #14560, 1000.000000000000000 ) ; +#12700 = ORIENTED_EDGE ( 'NONE', *, *, #78001, .T. ) ; +#12701 = CLOSED_SHELL ( 'NONE', ( #51939, #36906, #52191, #45768, #80734, #51582 ) ) ; +#12702 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12703 = VERTEX_POINT ( 'NONE', #81827 ) ; +#12705 = ORIENTED_EDGE ( 'NONE', *, *, #87025, .F. ) ; +#12704 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84346, #99563, #60886, #22047 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#12706 = LINE ( 'NONE', #97513, #23678 ) ; +#12707 = STYLED_ITEM ( 'NONE', ( #91941 ), #98714 ) ; +#12708 = SURFACE_STYLE_USAGE ( .BOTH. , #51618 ) ; +#12709 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12711 = SURFACE_SIDE_STYLE ('',( #65382 ) ) ; +#12710 = AXIS2_PLACEMENT_3D ( 'NONE', #100299, #24361, #39648 ) ; +#12712 = CYLINDRICAL_SURFACE ( 'NONE', #37355, 0.009999999999999998473 ) ; +#12714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12713 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12715 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#12716 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12717 = EDGE_LOOP ( 'NONE', ( #89497, #25957, #10362, #66012 ) ) ; +#12718 = FACE_OUTER_BOUND ( 'NONE', #69303, .T. ) ; +#12719 = ORIENTED_EDGE ( 'NONE', *, *, #94102, .T. ) ; +#12720 = EDGE_CURVE ( 'NONE', #91498, #29208, #49678, .T. ) ; +#12721 = CARTESIAN_POINT ( 'NONE', ( -0.1199320083468070064, -1.507611749840819915, 0.8100000000000000533 ) ) ; +#12722 = FILL_AREA_STYLE_COLOUR ( '', #90987 ) ; +#12723 = ADVANCED_FACE ( 'NONE', ( #87951 ), #42009, .F. ) ; +#12725 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12724 = CARTESIAN_POINT ( 'NONE', ( -0.04763654497925726150, -1.434908909145928169, 0.8099999999995960431 ) ) ; +#12726 = PLANE ( 'NONE', #85777 ) ; +#12727 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12728 = LINE ( 'NONE', #18943, #89982 ) ; +#12729 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12730 = FACE_OUTER_BOUND ( 'NONE', #11905, .T. ) ; +#12731 = STYLED_ITEM ( 'NONE', ( #29521 ), #32130 ) ; +#12732 = VECTOR ( 'NONE', #72918, 1000.000000000000000 ) ; +#12733 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19430, #41927, #82238, #33766 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#12734 = AXIS2_PLACEMENT_3D ( 'NONE', #86782, #94414, #24534 ) ; +#12735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12736 = EDGE_CURVE ( 'NONE', #19627, #22488, #22387, .T. ) ; +#12738 = LINE ( 'NONE', #85751, #79547 ) ; +#12737 = CARTESIAN_POINT ( 'NONE', ( -0.09034613274302537300, -1.219995095693503284, 0.8099999999999172307 ) ) ; +#12739 = FILL_AREA_STYLE_COLOUR ( '', #60378 ) ; +#12740 = VECTOR ( 'NONE', #71628, 1000.000000000000000 ) ; +#12741 = AXIS2_PLACEMENT_3D ( 'NONE', #67431, #98498, #21980 ) ; +#12742 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88825, 'distance_accuracy_value', 'NONE'); +#12743 = EDGE_LOOP ( 'NONE', ( #75792, #54458, #45338, #42182 ) ) ; +#12744 = CARTESIAN_POINT ( 'NONE', ( -0.9967138265693971100, -1.378727886756609955, 0.8299999999999999600 ) ) ; +#12745 = ADVANCED_FACE ( 'NONE', ( #21893 ), #100376, .F. ) ; +#12746 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12747 = FILL_AREA_STYLE_COLOUR ( '', #34751 ) ; +#12748 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.000000000000000000 ) ) ; +#12749 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36959 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64916, #96024, #26132 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12750 = SURFACE_SIDE_STYLE ('',( #95038 ) ) ; +#12751 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#12752 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980549, 0.000000000000000000 ) ) ; +#12753 = VECTOR ( 'NONE', #49260, 1000.000000000000114 ) ; +#12754 = EDGE_LOOP ( 'NONE', ( #94744, #17274, #81995, #56635 ) ) ; +#12755 = SURFACE_SIDE_STYLE ('',( #58839 ) ) ; +#12756 = VERTEX_POINT ( 'NONE', #44842 ) ; +#12757 = AXIS2_PLACEMENT_3D ( 'NONE', #16147, #17664, #39152 ) ; +#12758 = FILL_AREA_STYLE ('',( #59346 ) ) ; +#12759 = EDGE_CURVE ( 'NONE', #59128, #93347, #84676, .T. ) ; +#12760 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93329, 'distance_accuracy_value', 'NONE'); +#12761 = LINE ( 'NONE', #43972, #41727 ) ; +#12762 = VECTOR ( 'NONE', #37096, 1000.000000000000000 ) ; +#12763 = LINE ( 'NONE', #75624, #5269 ) ; +#12764 = SURFACE_STYLE_FILL_AREA ( #61344 ) ; +#12765 = FILL_AREA_STYLE_COLOUR ( '', #97441 ) ; +#12766 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12767 = VECTOR ( 'NONE', #6664, 999.9999999999998863 ) ; +#12768 = EDGE_CURVE ( 'NONE', #23447, #75309, #58033, .T. ) ; +#12769 = ORIENTED_EDGE ( 'NONE', *, *, #2651, .F. ) ; +#12770 = SURFACE_STYLE_USAGE ( .BOTH. , #92430 ) ; +#12771 = PRESENTATION_STYLE_ASSIGNMENT (( #66965 ) ) ; +#12772 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12773 = ORIENTED_EDGE ( 'NONE', *, *, #61523, .F. ) ; +#12774 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.400000000000000355, 0.000000000000000000 ) ) ; +#12775 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#12776 = ORIENTED_EDGE ( 'NONE', *, *, #17359, .F. ) ; +#12777 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97063 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63187, #86641, #96156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12778 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12779 = EDGE_CURVE ( 'NONE', #16425, #31313, #46352, .T. ) ; +#12781 = ADVANCED_FACE ( 'NONE', ( #76017 ), #84184, .F. ) ; +#12780 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97458 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88674, #18705, #2920 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12782 = CARTESIAN_POINT ( 'NONE', ( -2.300000000000000266, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#12783 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12784 = SURFACE_STYLE_USAGE ( .BOTH. , #21512 ) ; +#12785 = LINE ( 'NONE', #52678, #8760 ) ; +#12786 = EDGE_LOOP ( 'NONE', ( #74275, #74964, #93714, #13531 ) ) ; +#12788 = EDGE_CURVE ( 'NONE', #82206, #89004, #96339, .T. ) ; +#12787 = AXIS2_PLACEMENT_3D ( 'NONE', #31551, #911, #63232 ) ; +#12789 = EDGE_CURVE ( 'NONE', #75401, #39573, #15522, .T. ) ; +#12790 = PRESENTATION_STYLE_ASSIGNMENT (( #74664 ) ) ; +#12791 = ORIENTED_EDGE ( 'NONE', *, *, #60822, .T. ) ; +#12792 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12793 = ORIENTED_EDGE ( 'NONE', *, *, #35494, .F. ) ; +#12794 = ORIENTED_EDGE ( 'NONE', *, *, #56587, .T. ) ; +#12795 = FILL_AREA_STYLE_COLOUR ( '', #79110 ) ; +#12796 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#12797 = EDGE_CURVE ( 'NONE', #79322, #61427, #79050, .T. ) ; +#12798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12799 = CARTESIAN_POINT ( 'NONE', ( -0.4757099785863510011, -1.161113228842870049, 0.8100000000000000533 ) ) ; +#12800 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12801 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3038 ), #45473 ) ; +#12802 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, -3.099999999999992095, 0.000000000000000000 ) ) ; +#12803 = ORIENTED_EDGE ( 'NONE', *, *, #80541, .F. ) ; +#12804 = VERTEX_POINT ( 'NONE', #78519 ) ; +#12805 = VERTEX_POINT ( 'NONE', #16709 ) ; +#12806 = EDGE_CURVE ( 'NONE', #11537, #26719, #44553, .T. ) ; +#12807 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2784314575050770846, 0.1458578643762690474 ) ) ; +#12808 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12809 = VECTOR ( 'NONE', #88297, 1000.000000000000000 ) ; +#12810 = STYLED_ITEM ( 'NONE', ( #95608 ), #57083 ) ; +#12811 = ORIENTED_EDGE ( 'NONE', *, *, #24699, .F. ) ; +#12812 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21054 ), #76497 ) ; +#12813 = LINE ( 'NONE', #89984, #13898 ) ; +#12814 = PLANE ( 'NONE', #70948 ) ; +#12815 = ORIENTED_EDGE ( 'NONE', *, *, #100328, .F. ) ; +#12816 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8648700000000000276 ) ) ; +#12817 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12818 = ORIENTED_EDGE ( 'NONE', *, *, #16212, .T. ) ; +#12819 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#12820 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#12821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65089 ) ) ; +#12822 = SURFACE_STYLE_USAGE ( .BOTH. , #5190 ) ; +#12823 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#12824 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71584 ) ) ; +#12826 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#12825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12827 = PLANE ( 'NONE', #34405 ) ; +#12828 = AXIS2_PLACEMENT_3D ( 'NONE', #69691, #51901, #30903 ) ; +#12829 = VECTOR ( 'NONE', #44823, 1000.000000000000000 ) ; +#12830 = CARTESIAN_POINT ( 'NONE', ( -0.1791381517852550787, -0.9758639579753963789, 0.8100000000002820499 ) ) ; +#12831 = MANIFOLD_SOLID_BREP ( 'ÊäÈë3', #1246 ) ; +#12832 = ORIENTED_EDGE ( 'NONE', *, *, #92619, .F. ) ; +#12833 = ADVANCED_FACE ( 'NONE', ( #1442 ), #18221, .T. ) ; +#12834 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14459 ), #42231 ) ; +#12835 = CARTESIAN_POINT ( 'NONE', ( 1.438017692675660042, -1.296821915455180108, 0.8300000000000022915 ) ) ; +#12836 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43884 ), #74870 ) ; +#12837 = ADVANCED_FACE ( 'NONE', ( #64722 ), #33602, .T. ) ; +#12839 = CARTESIAN_POINT ( 'NONE', ( 1.628132030843780331, -1.431361989143759894, 0.8100000000000000533 ) ) ; +#12838 = CARTESIAN_POINT ( 'NONE', ( 0.4084453376902120181, -0.9740784349584099555, 0.8299999999999999600 ) ) ; +#12840 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12841 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#12842 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12843 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.876179938779915179, -0.02000000000000000042 ) ) ; +#12844 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53667 ) ) ; +#12845 = SURFACE_STYLE_USAGE ( .BOTH. , #35922 ) ; +#12846 = VERTEX_POINT ( 'NONE', #81589 ) ; +#12847 = LINE ( 'NONE', #36912, #37418 ) ; +#12848 = ORIENTED_EDGE ( 'NONE', *, *, #74080, .T. ) ; +#12850 = LINE ( 'NONE', #12346, #37930 ) ; +#12849 = PLANE ( 'NONE', #96322 ) ; +#12851 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, -11.36999999999999922 ) ) ; +#12852 = PRESENTATION_STYLE_ASSIGNMENT (( #28262 ) ) ; +#12853 = STYLED_ITEM ( 'NONE', ( #5020 ), #44109 ) ; +#12854 = SURFACE_STYLE_USAGE ( .BOTH. , #58938 ) ; +#12855 = PRESENTATION_STYLE_ASSIGNMENT (( #44065 ) ) ; +#12856 = VERTEX_POINT ( 'NONE', #98303 ) ; +#12857 = ADVANCED_FACE ( 'NONE', ( #97340 ), #18741, .T. ) ; +#12858 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12859 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12860 = CARTESIAN_POINT ( 'NONE', ( -2.433333333333333570, -3.500000000000000000, 0.000000000000000000 ) ) ; +#12861 = FACE_OUTER_BOUND ( 'NONE', #58168, .T. ) ; +#12862 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.4999999999999993339, 5.608055841774961276E-79 ) ) ; +#12863 = VECTOR ( 'NONE', #6236, 1000.000000000000000 ) ; +#12864 = LINE ( 'NONE', #75244, #26378 ) ; +#12865 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8648700000000000276 ) ) ; +#12866 = SURFACE_STYLE_FILL_AREA ( #28280 ) ; +#12867 = SURFACE_SIDE_STYLE ('',( #83410 ) ) ; +#12868 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88412 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66620, #12926, #90620 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12869 = VECTOR ( 'NONE', #26405, 1000.000000000000000 ) ; +#12870 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999278, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#12871 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.300000000000000266, -3.118622929693471946E-90 ) ) ; +#12872 = VERTEX_POINT ( 'NONE', #28440 ) ; +#12873 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#12874 = ORIENTED_EDGE ( 'NONE', *, *, #96450, .F. ) ; +#12875 = FILL_AREA_STYLE_COLOUR ( '', #82835 ) ; +#12876 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6398 ), #96088 ) ; +#12877 = CARTESIAN_POINT ( 'NONE', ( 1.186064574101910019, -0.9547617453595670378, 0.8299999999999999600 ) ) ; +#12878 = VECTOR ( 'NONE', #82790, 1000.000000000000000 ) ; +#12879 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#12880 = CARTESIAN_POINT ( 'NONE', ( 1.799170355476140015, -0.9218577280486121017, 0.8100000000000000533 ) ) ; +#12881 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#12882 = FILL_AREA_STYLE ('',( #21623 ) ) ; +#12883 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83183 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22236, #27673, #3156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12884 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.5000000000000000000, -13.40000000000000036 ) ) ; +#12885 = ORIENTED_EDGE ( 'NONE', *, *, #14652, .T. ) ; +#12886 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84668 ) ) ; +#12887 = LINE ( 'NONE', #36466, #3592 ) ; +#12889 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12888 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58569 ), #1540 ) ; +#12890 = ORIENTED_EDGE ( 'NONE', *, *, #71799, .T. ) ; +#12891 = CARTESIAN_POINT ( 'NONE', ( 4.798055124874956334, 3.548857875125043915, 0.8991599999999999593 ) ) ; +#12892 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#12893 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12894 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.000000000000000000 ) ) ; +#12895 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01085786437626902988, -0.1500000000000000222 ) ) ; +#12896 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21079 ) ) ; +#12897 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#12898 = VERTEX_POINT ( 'NONE', #81081 ) ; +#12899 = LINE ( 'NONE', #44119, #46554 ) ; +#12900 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15295 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47332, #64675, #95780 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12901 = ADVANCED_FACE ( 'NONE', ( #98794 ), #52943, .F. ) ; +#12902 = SURFACE_SIDE_STYLE ('',( #36484 ) ) ; +#12903 = LINE ( 'NONE', #59989, #32904 ) ; +#12904 = FACE_OUTER_BOUND ( 'NONE', #78028, .T. ) ; +#12905 = EDGE_LOOP ( 'NONE', ( #43911, #4793, #24732, #57140, #29433, #24589 ) ) ; +#12906 = SURFACE_STYLE_USAGE ( .BOTH. , #98179 ) ; +#12907 = PLANE ( 'NONE', #99310 ) ; +#12908 = CARTESIAN_POINT ( 'NONE', ( -1.185518397886804465, -1.217863928316329725, 0.8099999999998275246 ) ) ; +#12909 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#12910 = LINE ( 'NONE', #74281, #22264 ) ; +#12911 = ORIENTED_EDGE ( 'NONE', *, *, #42533, .F. ) ; +#12912 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#12913 = AXIS2_PLACEMENT_3D ( 'NONE', #98026, #21492, #35355 ) ; +#12914 = EDGE_CURVE ( 'NONE', #7621, #22571, #21425, .T. ) ; +#12915 = STYLED_ITEM ( 'NONE', ( #40743 ), #44289 ) ; +#12916 = ORIENTED_EDGE ( 'NONE', *, *, #40899, .T. ) ; +#12918 = ORIENTED_EDGE ( 'NONE', *, *, #60698, .T. ) ; +#12917 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, 0.000000000000000000 ) ) ; +#12919 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76668, 'distance_accuracy_value', 'NONE'); +#12920 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#12922 = CARTESIAN_POINT ( 'NONE', ( -1.384335136307129899, -1.374349516767729984, 0.8100000000000000533 ) ) ; +#12921 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12923 = SURFACE_STYLE_USAGE ( .BOTH. , #67118 ) ; +#12924 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#12925 = ORIENTED_EDGE ( 'NONE', *, *, #7103, .T. ) ; +#12926 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12927 = VERTEX_POINT ( 'NONE', #6862 ) ; +#12928 = CARTESIAN_POINT ( 'NONE', ( 1.268942880527089923, -1.510436674894549913, 0.8299999999999999600 ) ) ; +#12929 = FILL_AREA_STYLE_COLOUR ( '', #39783 ) ; +#12930 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#12931 = AXIS2_PLACEMENT_3D ( 'NONE', #4178, #42490, #81319 ) ; +#12932 = EDGE_LOOP ( 'NONE', ( #52198, #35276, #11586, #81607 ) ) ; +#12934 = LINE ( 'NONE', #61514, #99021 ) ; +#12933 = FILL_AREA_STYLE ('',( #21173 ) ) ; +#12935 = ORIENTED_EDGE ( 'NONE', *, *, #70361, .T. ) ; +#12936 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13525 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49443, #80600, #32115 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12937 = VECTOR ( 'NONE', #20038, 1000.000000000000000 ) ; +#12939 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5000000000000000000, 0.000000000000000000 ) ) ; +#12938 = LINE ( 'NONE', #91130, #16924 ) ; +#12940 = SURFACE_STYLE_USAGE ( .BOTH. , #20162 ) ; +#12941 = CARTESIAN_POINT ( 'NONE', ( 7.944680750250086909, 10.08959524974991240, 0.8991599999999999593 ) ) ; +#12942 = STYLED_ITEM ( 'NONE', ( #81241 ), #57497 ) ; +#12943 = PRESENTATION_STYLE_ASSIGNMENT (( #74315 ) ) ; +#12944 = VECTOR ( 'NONE', #63616, 1000.000000000000000 ) ; +#12945 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60146 ), #70072 ) ; +#12946 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#12947 = ORIENTED_EDGE ( 'NONE', *, *, #78715, .T. ) ; +#12948 = PLANE ( 'NONE', #36879 ) ; +#12949 = EDGE_LOOP ( 'NONE', ( #61654, #19770, #73558, #36736 ) ) ; +#12951 = FILL_AREA_STYLE ('',( #51855 ) ) ; +#12950 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12953 = SURFACE_SIDE_STYLE ('',( #89141 ) ) ; +#12952 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#12954 = FACE_OUTER_BOUND ( 'NONE', #76529, .T. ) ; +#12955 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91234 ), #94499 ) ; +#12956 = SURFACE_STYLE_FILL_AREA ( #97270 ) ; +#12957 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #9391, #19123, #71762, #72770, #11394, #96219, #32460, #81467, #3326, #71245, #88091 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.962700942152564965E-05, 3.898495090052829238E-05, 5.834632649917205905E-05, 7.800342256274978383E-05, 9.762704435041669605E-05, 0.0001169069817183986939, 0.0001363049500979956542, 0.0001565346846847532323 ), + .UNSPECIFIED. ) ; +#12958 = CIRCLE ( 'NONE', #44009, 0.09999999999999939493 ) ; +#12959 = FILL_AREA_STYLE_COLOUR ( '', #68735 ) ; +#12960 = VECTOR ( 'NONE', #92399, 1000.000000000000000 ) ; +#12961 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#12962 = SURFACE_STYLE_FILL_AREA ( #4857 ) ; +#12963 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#12964 = FILL_AREA_STYLE_COLOUR ( '', #19393 ) ; +#12965 = CARTESIAN_POINT ( 'NONE', ( 1.333992163213469917, -1.033922635360990050, 0.8299999999999999600 ) ) ; +#12966 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#12967 = SURFACE_STYLE_FILL_AREA ( #37547 ) ; +#12968 = EDGE_LOOP ( 'NONE', ( #4256, #13564, #55819, #54189, #72667, #34031, #49328, #52826 ) ) ; +#12969 = STYLED_ITEM ( 'NONE', ( #81016 ), #64428 ) ; +#12970 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12973 = PRESENTATION_STYLE_ASSIGNMENT (( #28863 ) ) ; +#12972 = SURFACE_STYLE_USAGE ( .BOTH. , #43176 ) ; +#12971 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12974 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100093, 'distance_accuracy_value', 'NONE'); +#12975 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12976 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#12977 = PLANE ( 'NONE', #56796 ) ; +#12978 = FILL_AREA_STYLE ('',( #27905 ) ) ; +#12979 = VERTEX_POINT ( 'NONE', #91702 ) ; +#12980 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#12981 = VECTOR ( 'NONE', #77529, 1000.000000000000000 ) ; +#12982 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#12983 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#12984 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8648700000000000276 ) ) ; +#12985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#12986 = ADVANCED_FACE ( 'NONE', ( #92207, #70235 ), #39108, .F. ) ; +#12987 = PRESENTATION_STYLE_ASSIGNMENT (( #5859 ) ) ; +#12988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6088 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74615, #7955, #36314 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#12989 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#12990 = FILL_AREA_STYLE_COLOUR ( '', #84337 ) ; +#12991 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999983236, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#12992 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#12993 = MANIFOLD_SOLID_BREP ( 'ÊäÈë169', #60114 ) ; +#12994 = PRESENTATION_STYLE_ASSIGNMENT (( #52905 ) ) ; +#12995 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#12996 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#12997 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#12998 = FILL_AREA_STYLE_COLOUR ( '', #1544 ) ; +#12999 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13000 = DIRECTION ( 'NONE', ( 0.7071072811865697361, -0.7071062811861716924, 0.000000000000000000 ) ) ; +#13001 = EDGE_CURVE ( 'NONE', #85062, #89851, #33486, .T. ) ; +#13002 = ORIENTED_EDGE ( 'NONE', *, *, #96845, .T. ) ; +#13003 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#13004 = SURFACE_SIDE_STYLE ('',( #66695 ) ) ; +#13005 = ADVANCED_FACE ( 'NONE', ( #52429 ), #55971, .F. ) ; +#13006 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#13007 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13008 = LINE ( 'NONE', #76367, #31182 ) ; +#13009 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13010 = STYLED_ITEM ( 'NONE', ( #40162 ), #93542 ) ; +#13011 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#13012 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#13013 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35930 ) ) ; +#13014 = ORIENTED_EDGE ( 'NONE', *, *, #55825, .T. ) ; +#13015 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#13016 = VERTEX_POINT ( 'NONE', #71770 ) ; +#13017 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.000000000000000000 ) ) ; +#13018 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#13020 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13019 = STYLED_ITEM ( 'NONE', ( #55821 ), #85646 ) ; +#13021 = EDGE_CURVE ( 'NONE', #56748, #68885, #94208, .T. ) ; +#13022 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32283 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82249, #29120, #20437 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13023 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52533 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55711, #38855, #8113 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13025 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24522 ), #83237 ) ; +#13026 = ORIENTED_EDGE ( 'NONE', *, *, #40357, .T. ) ; +#13027 = ORIENTED_EDGE ( 'NONE', *, *, #62174, .F. ) ; +#13028 = SURFACE_STYLE_FILL_AREA ( #27957 ) ; +#13029 = ORIENTED_EDGE ( 'NONE', *, *, #14670, .T. ) ; +#13030 = CARTESIAN_POINT ( 'NONE', ( 1.748219681435579931, -1.226312279485590073, 0.8299999999999999600 ) ) ; +#13031 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13032 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13033 = LINE ( 'NONE', #67717, #90738 ) ; +#13034 = EDGE_CURVE ( 'NONE', #55827, #53702, #95713, .T. ) ; +#13035 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #58400, #42085 ) ; +#13036 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13037 = VECTOR ( 'NONE', #35057, 1000.000000000000114 ) ; +#13039 = ORIENTED_EDGE ( 'NONE', *, *, #36375, .T. ) ; +#13038 = ORIENTED_EDGE ( 'NONE', *, *, #96763, .F. ) ; +#13040 = VECTOR ( 'NONE', #90030, 1000.000000000000000 ) ; +#13041 = VERTEX_POINT ( 'NONE', #32969 ) ; +#13042 = AXIS2_PLACEMENT_3D ( 'NONE', #91538, #21593, #52761 ) ; +#13043 = ORIENTED_EDGE ( 'NONE', *, *, #47627, .F. ) ; +#13044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13045 = SURFACE_SIDE_STYLE ('',( #74919 ) ) ; +#13046 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80319, 'distance_accuracy_value', 'NONE'); +#13047 = PRESENTATION_STYLE_ASSIGNMENT (( #83083 ) ) ; +#13048 = CARTESIAN_POINT ( 'NONE', ( 1.337707442669689994, -0.9199924700473179895, 0.8100000000000000533 ) ) ; +#13049 = CYLINDRICAL_SURFACE ( 'NONE', #60387, 0.05000000000000012768 ) ; +#13050 = CARTESIAN_POINT ( 'NONE', ( -1.162261078148919990, -0.8845231535185279492, 0.8100000000000000533 ) ) ; +#13051 = VERTEX_POINT ( 'NONE', #17616 ) ; +#13053 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13052 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#13054 = ORIENTED_EDGE ( 'NONE', *, *, #70850, .T. ) ; +#13055 = EDGE_LOOP ( 'NONE', ( #51216, #46379, #16490, #38221, #49665, #21486 ) ) ; +#13056 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47390 ) ) ; +#13057 = CARTESIAN_POINT ( 'NONE', ( 0.9977603010112831017, -1.128484622308769891, 0.8299999999999999600 ) ) ; +#13058 = EDGE_CURVE ( 'NONE', #44731, #43131, #79946, .T. ) ; +#13060 = SURFACE_SIDE_STYLE ('',( #45247 ) ) ; +#13059 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.1000000000000020040, 0.1829999999999709914 ) ) ; +#13061 = PLANE ( 'NONE', #55473 ) ; +#13062 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#13064 = EDGE_LOOP ( 'NONE', ( #61995, #94577, #87487, #67278, #99485, #94073 ) ) ; +#13063 = PLANE ( 'NONE', #87006 ) ; +#13065 = DIRECTION ( 'NONE', ( -0.7071067811865504593, 0.7071067811865445751, 0.000000000000000000 ) ) ; +#13066 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13067 = VERTEX_POINT ( 'NONE', #796 ) ; +#13069 = CYLINDRICAL_SURFACE ( 'NONE', #15883, 0.05000000000000012768 ) ; +#13068 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8099999999999111244 ) ) ; +#13070 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13071 = ORIENTED_EDGE ( 'NONE', *, *, #9950, .F. ) ; +#13072 = VERTEX_POINT ( 'NONE', #23806 ) ; +#13073 = EDGE_CURVE ( 'NONE', #13302, #58753, #18102, .T. ) ; +#13075 = CARTESIAN_POINT ( 'NONE', ( 1.296446609406725958, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#13074 = SURFACE_SIDE_STYLE ('',( #20814 ) ) ; +#13076 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#13077 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.000000000000000000, -13.25000000000000000 ) ) ; +#13078 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97267, #35545, #4361 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13079 = FACE_OUTER_BOUND ( 'NONE', #89065, .T. ) ; +#13080 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13081 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #50408, #23248 ), + ( #30355, #61056 ), + ( #46166, #91170 ), + ( #37565, #6339 ), + ( #52887, #92152 ), + ( #22224, #77336 ), + ( #93128, #44677 ), + ( #61563, #75842 ), + ( #69138, #39061 ), + ( #38056, #15012 ), + ( #5851, #7320 ), + ( #92634, #54394 ), + ( #30880, #91651 ), + ( #100699, #7818 ), + ( #14011, #85509 ), + ( #28879, #100210 ), + ( #77858, #21711 ), + ( #60066, #53875 ), + ( #21218, #37068 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06708277866639980602, 0.1312050869553300081, 0.1936380489846220021, 0.2553952748861270106, 0.3156922506608579870, 0.3746284903380590059, 0.4337407605315160009, 0.4928056895021900030, 0.5524831251440259772, 0.6123277341640710469, 0.6742432914735759786, 0.7378744975112909721, 0.8023045573449909540, 0.8673918161681609673, 0.9329440335921590499, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#13082 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13083 = CIRCLE ( 'NONE', #9802, 0.2000000000000005107 ) ; +#13084 = EDGE_LOOP ( 'NONE', ( #91114, #81237, #23984, #57106 ) ) ; +#13085 = ORIENTED_EDGE ( 'NONE', *, *, #97780, .T. ) ; +#13086 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13087 = CARTESIAN_POINT ( 'NONE', ( -0.01942805220116449946, -1.009819306370540071, 0.8100000000000000533 ) ) ; +#13088 = CARTESIAN_POINT ( 'NONE', ( 1.106746768919629975, -1.124851061273939967, 0.8299999999999999600 ) ) ; +#13089 = STYLED_ITEM ( 'NONE', ( #9143 ), #85805 ) ; +#13090 = SURFACE_STYLE_FILL_AREA ( #67282 ) ; +#13091 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13093 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#13092 = AXIS2_PLACEMENT_3D ( 'NONE', #80201, #40892, #18363 ) ; +#13094 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#13095 = FILL_AREA_STYLE_COLOUR ( '', #31584 ) ; +#13096 = EDGE_LOOP ( 'NONE', ( #6245, #99754, #98576, #30990 ) ) ; +#13097 = SURFACE_SIDE_STYLE ('',( #83137 ) ) ; +#13098 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13099 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13100 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13101 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13102 = FACE_OUTER_BOUND ( 'NONE', #61422, .T. ) ; +#13103 = LINE ( 'NONE', #30473, #7150 ) ; +#13104 = STYLED_ITEM ( 'NONE', ( #38443 ), #65791 ) ; +#13105 = CARTESIAN_POINT ( 'NONE', ( 1.897707761045830166, -1.292112914554750080, 0.8100000000000000533 ) ) ; +#13106 = EDGE_CURVE ( 'NONE', #16753, #80080, #99085, .T. ) ; +#13107 = EDGE_CURVE ( 'NONE', #72651, #19409, #47267, .T. ) ; +#13108 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.09999999999999996392, -0.02000000000000000042 ) ) ; +#13109 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#13110 = FACE_OUTER_BOUND ( 'NONE', #97336, .T. ) ; +#13111 = PLANE ( 'NONE', #91083 ) ; +#13112 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13113 = PLANE ( 'NONE', #94214 ) ; +#13114 = FILL_AREA_STYLE ('',( #68792 ) ) ; +#13115 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63731 ), #53939 ) ; +#13116 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13117 = ORIENTED_EDGE ( 'NONE', *, *, #68693, .T. ) ; +#13118 = CARTESIAN_POINT ( 'NONE', ( 0.07162059776835470737, -1.432643823895119128, 0.8099999999995994848 ) ) ; +#13119 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13120 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#13121 = ADVANCED_FACE ( 'NONE', ( #43129 ), #82947, .F. ) ; +#13122 = ORIENTED_EDGE ( 'NONE', *, *, #10899, .T. ) ; +#13123 = LINE ( 'NONE', #29528, #17255 ) ; +#13124 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#13125 = EDGE_CURVE ( 'NONE', #88016, #31030, #12910, .T. ) ; +#13126 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33827 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90044, #19602, #97184 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13127 = LINE ( 'NONE', #72993, #63920 ) ; +#13128 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#13129 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, 0.000000000000000000 ) ) ; +#13130 = VECTOR ( 'NONE', #65235, 1000.000000000000000 ) ; +#13131 = ORIENTED_EDGE ( 'NONE', *, *, #45168, .F. ) ; +#13132 = FACE_OUTER_BOUND ( 'NONE', #81669, .T. ) ; +#13133 = CYLINDRICAL_SURFACE ( 'NONE', #57927, 0.05000000000000012768 ) ; +#13134 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -1.699999999999999512, 0.1829999999999540328 ) ) ; +#13135 = EDGE_CURVE ( 'NONE', #6488, #99888, #66608, .T. ) ; +#13136 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#13137 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13138 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13139 = LINE ( 'NONE', #69302, #83683 ) ; +#13140 = EDGE_LOOP ( 'NONE', ( #7717, #38656, #63241, #69882 ) ) ; +#13141 = EDGE_CURVE ( 'NONE', #48138, #6530, #97706, .T. ) ; +#13142 = ORIENTED_EDGE ( 'NONE', *, *, #39025, .T. ) ; +#13143 = AXIS2_PLACEMENT_3D ( 'NONE', #49738, #3244, #11313 ) ; +#13144 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67085 ) ) ; +#13145 = ORIENTED_EDGE ( 'NONE', *, *, #66249, .T. ) ; +#13146 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#13147 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#13148 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992895, 3.500000000000000444, -1.195472123049164304E-89 ) ) ; +#13149 = AXIS2_PLACEMENT_3D ( 'NONE', #68996, #44519, #29229 ) ; +#13150 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13151 = ADVANCED_FACE ( 'NONE', ( #26329 ), #59511, .F. ) ; +#13152 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13153 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #67732, #50217 ) ; +#13154 = FILL_AREA_STYLE_COLOUR ( '', #21458 ) ; +#13155 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13156 = EDGE_CURVE ( 'NONE', #78170, #9772, #89105, .T. ) ; +#13158 = ORIENTED_EDGE ( 'NONE', *, *, #74854, .T. ) ; +#13157 = VERTEX_POINT ( 'NONE', #42642 ) ; +#13159 = MANIFOLD_SOLID_BREP ( 'ÊäÈë88', #35542 ) ; +#13160 = VECTOR ( 'NONE', #14078, 1000.000000000000000 ) ; +#13161 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16479 ), #70298 ) ; +#13162 = VERTEX_POINT ( 'NONE', #29802 ) ; +#13163 = ADVANCED_FACE ( 'NONE', ( #83943 ), #3824, .T. ) ; +#13164 = AXIS2_PLACEMENT_3D ( 'NONE', #89406, #9703, #9201 ) ; +#13165 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10827, 'distance_accuracy_value', 'NONE'); +#13166 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80106, 'distance_accuracy_value', 'NONE'); +#13167 = SURFACE_SIDE_STYLE ('',( #83207 ) ) ; +#13168 = VERTEX_POINT ( 'NONE', #7252 ) ; +#13169 = PRODUCT_DEFINITION ( 'δ֪', '', #42121, #55557 ) ; +#13170 = VERTEX_POINT ( 'NONE', #46096 ) ; +#13171 = VECTOR ( 'NONE', #25836, 1000.000000000000000 ) ; +#13172 = PRESENTATION_STYLE_ASSIGNMENT (( #20401 ) ) ; +#13173 = FILL_AREA_STYLE_COLOUR ( '', #6255 ) ; +#13176 = LINE ( 'NONE', #20918, #17291 ) ; +#13175 = STYLED_ITEM ( 'NONE', ( #40354 ), #20786 ) ; +#13174 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13177 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13178 = SURFACE_STYLE_FILL_AREA ( #36747 ) ; +#13179 = ORIENTED_EDGE ( 'NONE', *, *, #41965, .F. ) ; +#13180 = EDGE_LOOP ( 'NONE', ( #57889, #21352, #5528, #55253 ) ) ; +#13181 = PLANE ( 'NONE', #79661 ) ; +#13182 = EDGE_LOOP ( 'NONE', ( #91255, #27702, #4649, #28566 ) ) ; +#13183 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13184 = AXIS2_PLACEMENT_3D ( 'NONE', #89907, #4628, #28627 ) ; +#13185 = EDGE_CURVE ( 'NONE', #61128, #62347, #82210, .T. ) ; +#13186 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#13187 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90859 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81077, #73405, #48918 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13188 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13190 = ORIENTED_EDGE ( 'NONE', *, *, #25888, .F. ) ; +#13189 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13191 = FACE_OUTER_BOUND ( 'NONE', #71711, .T. ) ; +#13192 = LINE ( 'NONE', #38756, #30945 ) ; +#13193 = ORIENTED_EDGE ( 'NONE', *, *, #28953, .T. ) ; +#13194 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#13195 = SURFACE_SIDE_STYLE ('',( #75077 ) ) ; +#13196 = ORIENTED_EDGE ( 'NONE', *, *, #70378, .T. ) ; +#13197 = VERTEX_POINT ( 'NONE', #54311 ) ; +#13198 = EDGE_CURVE ( 'NONE', #37870, #69635, #33375, .T. ) ; +#13199 = FACE_OUTER_BOUND ( 'NONE', #55288, .T. ) ; +#13200 = SURFACE_STYLE_USAGE ( .BOTH. , #36768 ) ; +#13201 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13202 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#13203 = EDGE_CURVE ( 'NONE', #9565, #26074, #16992, .T. ) ; +#13204 = PRESENTATION_STYLE_ASSIGNMENT (( #58286 ) ) ; +#13205 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#13206 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.4999999999999998890, -0.02000000000000000042 ) ) ; +#13208 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13207 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#13209 = CARTESIAN_POINT ( 'NONE', ( 1.601121020982049892, -0.9216047924506349798, 0.8299999999999997380 ) ) ; +#13210 = ORIENTED_EDGE ( 'NONE', *, *, #95235, .F. ) ; +#13211 = CARTESIAN_POINT ( 'NONE', ( -1.023967505146820001, -1.493640573211080014, 0.8300000000000009592 ) ) ; +#13212 = ORIENTED_EDGE ( 'NONE', *, *, #29442, .T. ) ; +#13213 = VECTOR ( 'NONE', #44717, 1000.000000000000000 ) ; +#13214 = CARTESIAN_POINT ( 'NONE', ( -0.2295631936502020021, -1.479722134560319979, 0.8100000000000000533 ) ) ; +#13215 = LINE ( 'NONE', #99469, #67710 ) ; +#13216 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, 0.2399999999999999356 ) ) ; +#13217 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333326198, 1.100000000000000089, 0.000000000000000000 ) ) ; +#13218 = SURFACE_STYLE_USAGE ( .BOTH. , #45402 ) ; +#13219 = PRESENTATION_STYLE_ASSIGNMENT (( #59814 ) ) ; +#13220 = SURFACE_SIDE_STYLE ('',( #21452 ) ) ; +#13221 = PLANE ( 'NONE', #8339 ) ; +#13223 = VECTOR ( 'NONE', #5589, 1000.000000000000000 ) ; +#13222 = CARTESIAN_POINT ( 'NONE', ( 4.410099790157880228, 1.446167217082579892, -11.91551182404470133 ) ) ; +#13224 = PLANE ( 'NONE', #51257 ) ; +#13225 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#13226 = EDGE_CURVE ( 'NONE', #10584, #56923, #56859, .T. ) ; +#13227 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76930 ), #39384 ) ; +#13228 = VECTOR ( 'NONE', #38442, 1000.000000000000000 ) ; +#13230 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.000000000000000000 ) ) ; +#13229 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.100000000000000089, -3.118622929693471946E-90 ) ) ; +#13231 = SURFACE_SIDE_STYLE ('',( #60803 ) ) ; +#13232 = AXIS2_PLACEMENT_3D ( 'NONE', #87638, #40183, #23862 ) ; +#13233 = ORIENTED_EDGE ( 'NONE', *, *, #28872, .T. ) ; +#13234 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16571 ) ) ; +#13235 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7920, 'distance_accuracy_value', 'NONE'); +#13236 = FILL_AREA_STYLE ('',( #52148 ) ) ; +#13237 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.000000000000000000 ) ) ; +#13238 = EDGE_CURVE ( 'NONE', #72252, #63443, #63989, .T. ) ; +#13239 = CARTESIAN_POINT ( 'NONE', ( 0.4511079906226275194, -1.140803386432353683, 0.8099999999999999423 ) ) ; +#13240 = SURFACE_STYLE_FILL_AREA ( #36813 ) ; +#13241 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01500000000000000291, 0.000000000000000000 ) ) ; +#13242 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000059508, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#13243 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#13244 = FILL_AREA_STYLE ('',( #16682 ) ) ; +#13245 = VECTOR ( 'NONE', #40127, 1000.000000000000000 ) ; +#13246 = ORIENTED_EDGE ( 'NONE', *, *, #40693, .F. ) ; +#13247 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13248 = ORIENTED_EDGE ( 'NONE', *, *, #42358, .T. ) ; +#13250 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90157, 'distance_accuracy_value', 'NONE'); +#13249 = STYLED_ITEM ( 'NONE', ( #16605 ), #69767 ) ; +#13251 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94023, 'distance_accuracy_value', 'NONE'); +#13252 = CARTESIAN_POINT ( 'NONE', ( -0.1711130133853419888, 2.469409075926969788, 0.8299999999999999600 ) ) ; +#13253 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13254 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#13255 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8648700000000000276 ) ) ; +#13256 = CARTESIAN_POINT ( 'NONE', ( -0.5238200612200851758, -3.099999999999989875, 0.000000000000000000 ) ) ; +#13257 = PRESENTATION_STYLE_ASSIGNMENT (( #60347 ) ) ; +#13258 = ORIENTED_EDGE ( 'NONE', *, *, #88782, .F. ) ; +#13259 = FILL_AREA_STYLE_COLOUR ( '', #41729 ) ; +#13260 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#13261 = VERTEX_POINT ( 'NONE', #47145 ) ; +#13262 = SURFACE_STYLE_FILL_AREA ( #75155 ) ; +#13263 = ORIENTED_EDGE ( 'NONE', *, *, #49292, .F. ) ; +#13264 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82244, #44398, #73569, #97521 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#13265 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13266 = SURFACE_SIDE_STYLE ('',( #5149 ) ) ; +#13267 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13268 = DIRECTION ( 'NONE', ( -5.103411969279230082E-12, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13269 = PRESENTATION_STYLE_ASSIGNMENT (( #21023 ) ) ; +#13270 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#13271 = EDGE_CURVE ( 'NONE', #98312, #38918, #72152, .T. ) ; +#13273 = ORIENTED_EDGE ( 'NONE', *, *, #38449, .T. ) ; +#13272 = ORIENTED_EDGE ( 'NONE', *, *, #79033, .F. ) ; +#13274 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626904202, 0.1400000000000000133 ) ) ; +#13275 = PRESENTATION_STYLE_ASSIGNMENT (( #5157 ) ) ; +#13276 = ORIENTED_EDGE ( 'NONE', *, *, #63251, .F. ) ; +#13278 = CARTESIAN_POINT ( 'NONE', ( -0.5167674196284709476, -0.9767818844061101347, 0.8299999999999999600 ) ) ; +#13277 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13279 = ORIENTED_EDGE ( 'NONE', *, *, #71165, .F. ) ; +#13280 = ORIENTED_EDGE ( 'NONE', *, *, #31892, .T. ) ; +#13281 = PLANE ( 'NONE', #20412 ) ; +#13282 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#13283 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13284 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96434 ) ) ; +#13285 = PLANE ( 'NONE', #2237 ) ; +#13286 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#13287 = VERTEX_POINT ( 'NONE', #86460 ) ; +#13288 = ORIENTED_EDGE ( 'NONE', *, *, #16452, .T. ) ; +#13289 = VERTEX_POINT ( 'NONE', #55351 ) ; +#13290 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14558 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16519, #63552, #65038 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13291 = CIRCLE ( 'NONE', #23156, 0.009999999999999998473 ) ; +#13292 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57432 ) ) ; +#13293 = ADVANCED_FACE ( 'NONE', ( #16465 ), #77788, .F. ) ; +#13294 = AXIS2_PLACEMENT_3D ( 'NONE', #58512, #64124, #25342 ) ; +#13296 = ORIENTED_EDGE ( 'NONE', *, *, #7414, .T. ) ; +#13295 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#13297 = VECTOR ( 'NONE', #7554, 1000.000000000000000 ) ; +#13298 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#13299 = LINE ( 'NONE', #51209, #23738 ) ; +#13300 = VECTOR ( 'NONE', #15079, 1000.000000000000000 ) ; +#13301 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#13302 = VERTEX_POINT ( 'NONE', #41028 ) ; +#13303 = SURFACE_SIDE_STYLE ('',( #100534 ) ) ; +#13304 = PRESENTATION_STYLE_ASSIGNMENT (( #58900 ) ) ; +#13305 = VERTEX_POINT ( 'NONE', #8754 ) ; +#13306 = EDGE_CURVE ( 'NONE', #99033, #20063, #33362, .T. ) ; +#13307 = AXIS2_PLACEMENT_3D ( 'NONE', #90895, #27627, #74070 ) ; +#13308 = FILL_AREA_STYLE_COLOUR ( '', #72526 ) ; +#13309 = LINE ( 'NONE', #100901, #50037 ) ; +#13310 = STYLED_ITEM ( 'NONE', ( #15952 ), #66702 ) ; +#13311 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#13312 = PRESENTATION_STYLE_ASSIGNMENT (( #83359 ) ) ; +#13313 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24820 ) ) ; +#13314 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#13315 = CARTESIAN_POINT ( 'NONE', ( -1.118621473632941399, -1.160211654383759061, 0.8099999999998702682 ) ) ; +#13316 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13317 = MANIFOLD_SOLID_BREP ( 'ÊäÈë102', #100671 ) ; +#13318 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#13319 = VERTEX_POINT ( 'NONE', #50215 ) ; +#13320 = ADVANCED_FACE ( 'NONE', ( #49698 ), #63003, .T. ) ; +#13321 = SURFACE_STYLE_USAGE ( .BOTH. , #81876 ) ; +#13322 = PLANE ( 'NONE', #9348 ) ; +#13323 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14281 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97076, #65452, #57332 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13324 = EDGE_CURVE ( 'NONE', #27209, #258, #34380, .T. ) ; +#13326 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8099999999998839240 ) ) ; +#13325 = SURFACE_STYLE_FILL_AREA ( #36902 ) ; +#13327 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#13328 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#13329 = FILL_AREA_STYLE ('',( #43543 ) ) ; +#13330 = VECTOR ( 'NONE', #75468, 1000.000000000000000 ) ; +#13331 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13332 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13333 = FILL_AREA_STYLE_COLOUR ( '', #81782 ) ; +#13334 = ORIENTED_EDGE ( 'NONE', *, *, #83192, .T. ) ; +#13335 = VECTOR ( 'NONE', #39241, 1000.000000000000000 ) ; +#13336 = EDGE_CURVE ( 'NONE', #34706, #76926, #85886, .T. ) ; +#13337 = SURFACE_STYLE_FILL_AREA ( #44542 ) ; +#13338 = EDGE_CURVE ( 'NONE', #83808, #87953, #17989, .T. ) ; +#13339 = EDGE_LOOP ( 'NONE', ( #32373, #40560, #32301, #63963 ) ) ; +#13341 = LINE ( 'NONE', #68024, #29823 ) ; +#13340 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76000 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50458, #12024, #13036 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13342 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62359 ) ) ; +#13343 = FACE_OUTER_BOUND ( 'NONE', #6419, .T. ) ; +#13344 = ADVANCED_FACE ( 'NONE', ( #34877 ), #96103, .F. ) ; +#13345 = EDGE_CURVE ( 'NONE', #3215, #16927, #66493, .T. ) ; +#13347 = VECTOR ( 'NONE', #57682, 1000.000000000000000 ) ; +#13346 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13348 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65618 ), #29741 ) ; +#13349 = PRESENTATION_STYLE_ASSIGNMENT (( #51247 ) ) ; +#13350 = VERTEX_POINT ( 'NONE', #4696 ) ; +#13351 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#13352 = LINE ( 'NONE', #43561, #54437 ) ; +#13353 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13354 = PRESENTATION_STYLE_ASSIGNMENT (( #21595 ) ) ; +#13355 = EDGE_CURVE ( 'NONE', #7769, #28686, #89486, .T. ) ; +#13356 = VECTOR ( 'NONE', #81698, 1000.000000000000000 ) ; +#13357 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13358 = STYLED_ITEM ( 'NONE', ( #58934 ), #18786 ) ; +#13359 = VECTOR ( 'NONE', #25956, 1000.000000000000000 ) ; +#13360 = PRESENTATION_STYLE_ASSIGNMENT (( #75242 ) ) ; +#13361 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.805577711833473734E-15, 0.000000000000000000 ) ) ; +#13362 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13363 = LINE ( 'NONE', #34946, #44150 ) ; +#13364 = PRESENTATION_STYLE_ASSIGNMENT (( #90040 ) ) ; +#13366 = FACE_OUTER_BOUND ( 'NONE', #38452, .T. ) ; +#13365 = VECTOR ( 'NONE', #72546, 1000.000000000000114 ) ; +#13367 = EDGE_CURVE ( 'NONE', #1951, #85582, #58882, .T. ) ; +#13368 = AXIS2_PLACEMENT_3D ( 'NONE', #33322, #64460, #93535 ) ; +#13369 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90021, 'distance_accuracy_value', 'NONE'); +#13370 = FACE_OUTER_BOUND ( 'NONE', #45460, .T. ) ; +#13371 = VERTEX_POINT ( 'NONE', #29206 ) ; +#13372 = FACE_OUTER_BOUND ( 'NONE', #3663, .T. ) ; +#13374 = EDGE_LOOP ( 'NONE', ( #20791, #78323, #89979, #34537 ) ) ; +#13373 = VECTOR ( 'NONE', #46637, 1000.000000000000000 ) ; +#13375 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97113, 'distance_accuracy_value', 'NONE'); +#13376 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27440, 'distance_accuracy_value', 'NONE'); +#13377 = CARTESIAN_POINT ( 'NONE', ( 1.169384343503750090, -0.9551946040733080290, 0.8100000000000000533 ) ) ; +#13378 = SURFACE_STYLE_FILL_AREA ( #28289 ) ; +#13379 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13380 = FACE_OUTER_BOUND ( 'NONE', #34462, .T. ) ; +#13381 = VECTOR ( 'NONE', #53322, 1000.000000000000000 ) ; +#13382 = CARTESIAN_POINT ( 'NONE', ( 1.847806625102409894, -0.9622763341455700115, 0.8299999999999999600 ) ) ; +#13383 = CARTESIAN_POINT ( 'NONE', ( 5.802146875124987169, 2.544766875124987227, 0.8648700000000000276 ) ) ; +#13384 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8648700000000000276 ) ) ; +#13385 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 1.699999999999999956, 3.495651678170121160E-76 ) ) ; +#13386 = VERTEX_POINT ( 'NONE', #53191 ) ; +#13387 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13388 = FACE_OUTER_BOUND ( 'NONE', #54788, .T. ) ; +#13389 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57132, 'distance_accuracy_value', 'NONE'); +#13390 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13391 = SURFACE_SIDE_STYLE ('',( #52299 ) ) ; +#13392 = VERTEX_POINT ( 'NONE', #68971 ) ; +#13393 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13394 = SURFACE_STYLE_USAGE ( .BOTH. , #27314 ) ; +#13395 = CARTESIAN_POINT ( 'NONE', ( -1.316686852848500067, -1.306787212278190058, 0.8299999999999999600 ) ) ; +#13396 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13397 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#13398 = ADVANCED_FACE ( 'NONE', ( #30676 ), #99546, .T. ) ; +#13399 = ORIENTED_EDGE ( 'NONE', *, *, #14663, .T. ) ; +#13400 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13401 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8648700000000000276 ) ) ; +#13402 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #721, 'distance_accuracy_value', 'NONE'); +#13403 = STYLED_ITEM ( 'NONE', ( #522 ), #52827 ) ; +#13404 = ADVANCED_FACE ( 'NONE', ( #5667 ), #21530, .T. ) ; +#13405 = CARTESIAN_POINT ( 'NONE', ( -1.323820061220085220, 3.099999999999990319, 0.000000000000000000 ) ) ; +#13406 = VERTEX_POINT ( 'NONE', #14326 ) ; +#13407 = FILL_AREA_STYLE_COLOUR ( '', #46443 ) ; +#13408 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57550 ) ) ; +#13410 = FILL_AREA_STYLE_COLOUR ( '', #26657 ) ; +#13409 = AXIS2_PLACEMENT_3D ( 'NONE', #98885, #53029, #13631 ) ; +#13411 = CARTESIAN_POINT ( 'NONE', ( -1.150425319289392956, -1.225742884720179005, 0.8099999999998219735 ) ) ; +#13412 = CARTESIAN_POINT ( 'NONE', ( 1.612727879620370119, -1.495500525511030077, 0.8300000000000001821 ) ) ; +#13413 = ORIENTED_EDGE ( 'NONE', *, *, #93094, .T. ) ; +#13414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78882 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42781, #65251, #72923 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13415 = VECTOR ( 'NONE', #79991, 1000.000000000000000 ) ; +#13416 = ORIENTED_EDGE ( 'NONE', *, *, #61803, .F. ) ; +#13418 = ORIENTED_EDGE ( 'NONE', *, *, #59841, .F. ) ; +#13417 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#13420 = CARTESIAN_POINT ( 'NONE', ( -1.352086563886500059, -1.432289833627879982, 0.8100000000000000533 ) ) ; +#13419 = PRESENTATION_STYLE_ASSIGNMENT (( #98681 ) ) ; +#13421 = VECTOR ( 'NONE', #4157, 1000.000000000000000 ) ; +#13422 = LINE ( 'NONE', #52823, #62726 ) ; +#13423 = FILL_AREA_STYLE_COLOUR ( '', #37391 ) ; +#13424 = EDGE_LOOP ( 'NONE', ( #8100, #20351, #27373, #63133 ) ) ; +#13425 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 9.806753000000000497, 0.8648700000000000276 ) ) ; +#13426 = SURFACE_STYLE_FILL_AREA ( #77289 ) ; +#13427 = ORIENTED_EDGE ( 'NONE', *, *, #25118, .T. ) ; +#13428 = ADVANCED_FACE ( 'NONE', ( #67969 ), #6641, .T. ) ; +#13429 = CARTESIAN_POINT ( 'NONE', ( 0.4837535085725997996, 0.4169617478988522641, 0.8100000000000000533 ) ) ; +#13430 = LINE ( 'NONE', #43142, #35006 ) ; +#13431 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27809 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85055, #53425, #92205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13432 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13433 = SURFACE_STYLE_FILL_AREA ( #52339 ) ; +#13434 = AXIS2_PLACEMENT_3D ( 'NONE', #54885, #16028, #18561 ) ; +#13435 = CARTESIAN_POINT ( 'NONE', ( 8.404300249749912410, 1.979081249749912397, 0.8648700000000000276 ) ) ; +#13436 = ORIENTED_EDGE ( 'NONE', *, *, #62009, .T. ) ; +#13437 = PRESENTATION_STYLE_ASSIGNMENT (( #83477 ) ) ; +#13438 = ORIENTED_EDGE ( 'NONE', *, *, #98157, .F. ) ; +#13439 = STYLED_ITEM ( 'NONE', ( #40806 ), #60631 ) ; +#13440 = AXIS2_PLACEMENT_3D ( 'NONE', #83307, #58853, #12256 ) ; +#13442 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13441 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13443 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#13444 = FILL_AREA_STYLE_COLOUR ( '', #75128 ) ; +#13445 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44476 ), #34701 ) ; +#13446 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13447 = PLANE ( 'NONE', #81710 ) ; +#13448 = CIRCLE ( 'NONE', #73896, 0.2137111836784290342 ) ; +#13449 = ORIENTED_EDGE ( 'NONE', *, *, #42131, .F. ) ; +#13450 = ORIENTED_EDGE ( 'NONE', *, *, #25139, .F. ) ; +#13451 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13452 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#13453 = SURFACE_SIDE_STYLE ('',( #75317 ) ) ; +#13454 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65743 ), #44560 ) ; +#13455 = FILL_AREA_STYLE ('',( #67633 ) ) ; +#13456 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13457 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13458 = PLANE ( 'NONE', #85091 ) ; +#13459 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#13460 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#13461 = ORIENTED_EDGE ( 'NONE', *, *, #26044, .T. ) ; +#13462 = PRESENTATION_STYLE_ASSIGNMENT (( #97756 ) ) ; +#13463 = SURFACE_STYLE_FILL_AREA ( #82505 ) ; +#13464 = VECTOR ( 'NONE', #36158, 1000.000000000000000 ) ; +#13465 = SURFACE_STYLE_USAGE ( .BOTH. , #91156 ) ; +#13466 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#13468 = ADVANCED_FACE ( 'NONE', ( #62885 ), #70503, .T. ) ; +#13467 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#13469 = SURFACE_SIDE_STYLE ('',( #85500 ) ) ; +#13470 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#13471 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51051 ), #2135 ) ; +#13472 = SURFACE_STYLE_USAGE ( .BOTH. , #71592 ) ; +#13473 = SURFACE_STYLE_USAGE ( .BOTH. , #12467 ) ; +#13474 = ORIENTED_EDGE ( 'NONE', *, *, #94002, .F. ) ; +#13475 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 0.6999999999999999556, -13.40000000000000036 ) ) ; +#13476 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13477 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13478 = ADVANCED_FACE ( 'NONE', ( #25099 ), #24077, .T. ) ; +#13479 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33985 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72829, #35051, #65662 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13480 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#13481 = SURFACE_STYLE_FILL_AREA ( #28880 ) ; +#13482 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#13483 = FACE_OUTER_BOUND ( 'NONE', #97375, .T. ) ; +#13484 = LINE ( 'NONE', #45175, #17972 ) ; +#13485 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#13486 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#13487 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86976 ), #80425 ) ; +#13488 = CARTESIAN_POINT ( 'NONE', ( 11.38829049949982597, 7.565224500500177029, 0.8991599999999999593 ) ) ; +#13489 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#13490 = ADVANCED_FACE ( 'NONE', ( #17382 ), #39357, .T. ) ; +#13491 = SURFACE_STYLE_USAGE ( .BOTH. , #21722 ) ; +#13492 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13493 = SURFACE_STYLE_FILL_AREA ( #83026 ) ; +#13494 = FILL_AREA_STYLE_COLOUR ( '', #1521 ) ; +#13495 = AXIS2_PLACEMENT_3D ( 'NONE', #1757, #95634, #16020 ) ; +#13496 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#13497 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13498 = FILL_AREA_STYLE_COLOUR ( '', #7878 ) ; +#13499 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58968, 'distance_accuracy_value', 'NONE'); +#13500 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000059508, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#13501 = SURFACE_STYLE_USAGE ( .BOTH. , #23769 ) ; +#13502 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23355 ) ) ; +#13503 = VECTOR ( 'NONE', #44694, 1000.000000000000000 ) ; +#13504 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#13505 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#13506 = FACE_OUTER_BOUND ( 'NONE', #44724, .T. ) ; +#13507 = CARTESIAN_POINT ( 'NONE', ( -0.9118498257241719473, -1.330101555947649894, 0.8299999999999999600 ) ) ; +#13508 = VERTEX_POINT ( 'NONE', #94975 ) ; +#13509 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76355, 'distance_accuracy_value', 'NONE'); +#13510 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33130 ), #16828 ) ; +#13511 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96715 ), #20130 ) ; +#13512 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90387, 'distance_accuracy_value', 'NONE'); +#13513 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57662 ) ) ; +#13514 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#13515 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1399999999999999856 ) ) ; +#13516 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13517 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13518 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13519 = ORIENTED_EDGE ( 'NONE', *, *, #77261, .F. ) ; +#13520 = VECTOR ( 'NONE', #66879, 1000.000000000000000 ) ; +#13521 = ORIENTED_EDGE ( 'NONE', *, *, #3111, .T. ) ; +#13522 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13523 = VECTOR ( 'NONE', #99714, 1000.000000000000000 ) ; +#13524 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13525 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49443, 'distance_accuracy_value', 'NONE'); +#13526 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.6999999999999988454, 0.8299999999999999600 ) ) ; +#13527 = SURFACE_STYLE_FILL_AREA ( #5890 ) ; +#13528 = ADVANCED_FACE ( 'NONE', ( #55228 ), #93945, .T. ) ; +#13529 = FACE_OUTER_BOUND ( 'NONE', #24050, .T. ) ; +#13530 = ORIENTED_EDGE ( 'NONE', *, *, #72438, .F. ) ; +#13531 = ORIENTED_EDGE ( 'NONE', *, *, #49450, .T. ) ; +#13532 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#13533 = AXIS2_PLACEMENT_3D ( 'NONE', #29302, #28786, #82931 ) ; +#13534 = ORIENTED_EDGE ( 'NONE', *, *, #388, .F. ) ; +#13535 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13536 = CARTESIAN_POINT ( 'NONE', ( 0.4101069733384740124, -1.272991977397700092, 0.8299999999999999600 ) ) ; +#13537 = LINE ( 'NONE', #75898, #22014 ) ; +#13538 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #10342, #54837 ) ; +#13539 = PLANE ( 'NONE', #52584 ) ; +#13541 = ORIENTED_EDGE ( 'NONE', *, *, #16508, .T. ) ; +#13540 = ORIENTED_EDGE ( 'NONE', *, *, #29338, .T. ) ; +#13542 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78849 ) ) ; +#13543 = ORIENTED_EDGE ( 'NONE', *, *, #26468, .T. ) ; +#13544 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13546 = CARTESIAN_POINT ( 'NONE', ( 1.367410627668359968, -0.9444486738239200596, 0.8100000000000000533 ) ) ; +#13545 = CARTESIAN_POINT ( 'NONE', ( 0.4642887493627290141, -0.9252028835730660150, 0.8100000000000000533 ) ) ; +#13547 = CIRCLE ( 'NONE', #70687, 0.1999999999999996503 ) ; +#13548 = ADVANCED_FACE ( 'NONE', ( #94478 ), #32737, .T. ) ; +#13549 = DIRECTION ( 'NONE', ( 0.7071067816865476141, 0.7071067806865475314, 0.000000000000000000 ) ) ; +#13550 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#13551 = CARTESIAN_POINT ( 'NONE', ( -1.370884097750779906, -1.038425069758839969, 0.8100000000000000533 ) ) ; +#13552 = VERTEX_POINT ( 'NONE', #33238 ) ; +#13554 = SURFACE_STYLE_USAGE ( .BOTH. , #98812 ) ; +#13553 = PRESENTATION_STYLE_ASSIGNMENT (( #99782 ) ) ; +#13555 = EDGE_CURVE ( 'NONE', #19650, #95875, #64370, .T. ) ; +#13556 = EDGE_LOOP ( 'NONE', ( #6679, #36614, #55467, #37721 ) ) ; +#13557 = VERTEX_POINT ( 'NONE', #64870 ) ; +#13558 = CARTESIAN_POINT ( 'NONE', ( 1.016962903650600047, -1.153389236204189983, 0.8299999999999999600 ) ) ; +#13560 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13559 = FILL_AREA_STYLE_COLOUR ( '', #62532 ) ; +#13561 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13562 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999990008, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#13564 = ORIENTED_EDGE ( 'NONE', *, *, #81466, .F. ) ; +#13563 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#13565 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#13566 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13567 = SURFACE_SIDE_STYLE ('',( #83611 ) ) ; +#13568 = STYLED_ITEM ( 'NONE', ( #86267 ), #19660 ) ; +#13569 = VERTEX_POINT ( 'NONE', #51087 ) ; +#13571 = SURFACE_STYLE_USAGE ( .BOTH. , #84596 ) ; +#13570 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#13572 = ORIENTED_EDGE ( 'NONE', *, *, #55269, .F. ) ; +#13573 = ORIENTED_EDGE ( 'NONE', *, *, #42364, .T. ) ; +#13575 = EDGE_CURVE ( 'NONE', #98893, #16570, #25586, .T. ) ; +#13574 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94550, #55789, #2170, #64447 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#13576 = PRESENTATION_STYLE_ASSIGNMENT (( #7415 ) ) ; +#13577 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13578 = PRESENTATION_STYLE_ASSIGNMENT (( #45266 ) ) ; +#13579 = EDGE_CURVE ( 'NONE', #37993, #85330, #57758, .T. ) ; +#13581 = VECTOR ( 'NONE', #74834, 1000.000000000000000 ) ; +#13580 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13582 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40809 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48992, #42332, #96909 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13583 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57727 ) ) ; +#13584 = FACE_OUTER_BOUND ( 'NONE', #18674, .T. ) ; +#13585 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13586 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36739 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88017, #17533, #64536 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13587 = PRESENTATION_STYLE_ASSIGNMENT (( #53485 ) ) ; +#13588 = PLANE ( 'NONE', #21626 ) ; +#13589 = VECTOR ( 'NONE', #95194, 1000.000000000000000 ) ; +#13590 = ORIENTED_EDGE ( 'NONE', *, *, #39607, .T. ) ; +#13591 = SURFACE_STYLE_USAGE ( .BOTH. , #43803 ) ; +#13592 = ORIENTED_EDGE ( 'NONE', *, *, #11225, .T. ) ; +#13593 = SURFACE_STYLE_USAGE ( .BOTH. , #21329 ) ; +#13594 = CARTESIAN_POINT ( 'NONE', ( -0.04570195398950489818, -0.9814610950457439698, 0.8299999999999999600 ) ) ; +#13595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10296 ), #73963 ) ; +#13597 = EDGE_CURVE ( 'NONE', #78062, #16593, #42897, .T. ) ; +#13596 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8648700000000000276 ) ) ; +#13598 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39601 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17639, #79976, #42178 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13599 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#13600 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13601 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#13602 = EDGE_LOOP ( 'NONE', ( #29655, #72890, #7995, #11806 ) ) ; +#13603 = SURFACE_SIDE_STYLE ('',( #84631 ) ) ; +#13604 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#13605 = FACE_OUTER_BOUND ( 'NONE', #93073, .T. ) ; +#13606 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13607 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69091 ), #623 ) ; +#13608 = FACE_OUTER_BOUND ( 'NONE', #25918, .T. ) ; +#13609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26977 ), #38332 ) ; +#13611 = LINE ( 'NONE', #75972, #1086 ) ; +#13612 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#13613 = ADVANCED_FACE ( 'NONE', ( #41902 ), #81225, .F. ) ; +#13614 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8199999999999999512 ) ) ; +#13615 = FILL_AREA_STYLE_COLOUR ( '', #30434 ) ; +#13616 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#13617 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13618 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13619 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13620 = STYLED_ITEM ( 'NONE', ( #43493 ), #53365 ) ; +#13621 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18492, 'distance_accuracy_value', 'NONE'); +#13622 = ORIENTED_EDGE ( 'NONE', *, *, #48810, .T. ) ; +#13623 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#13624 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822763000000000133, 0.8991599999999999593 ) ) ; +#13625 = ORIENTED_EDGE ( 'NONE', *, *, #66423, .T. ) ; +#13626 = FILL_AREA_STYLE ('',( #14153 ) ) ; +#13627 = PLANE ( 'NONE', #33913 ) ; +#13628 = FILL_AREA_STYLE_COLOUR ( '', #100569 ) ; +#13629 = AXIS2_PLACEMENT_3D ( 'NONE', #33156, #23487, #2013 ) ; +#13631 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#13630 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#13632 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33744, 'distance_accuracy_value', 'NONE'); +#13633 = EDGE_CURVE ( 'NONE', #35754, #25100, #73038, .T. ) ; +#13634 = FACE_OUTER_BOUND ( 'NONE', #65578, .T. ) ; +#13635 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.000000000000000000 ) ) ; +#13636 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69054 ) ) ; +#13637 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8555 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76021, #91823, #6013 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13638 = LINE ( 'NONE', #5016, #53241 ) ; +#13639 = EDGE_CURVE ( 'NONE', #45984, #83808, #18386, .T. ) ; +#13640 = ORIENTED_EDGE ( 'NONE', *, *, #49518, .T. ) ; +#13641 = SURFACE_SIDE_STYLE ('',( #90826 ) ) ; +#13642 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13643 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#13644 = SURFACE_STYLE_FILL_AREA ( #100361 ) ; +#13645 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58132, 'distance_accuracy_value', 'NONE'); +#13646 = FACE_OUTER_BOUND ( 'NONE', #5814, .T. ) ; +#13647 = VECTOR ( 'NONE', #33044, 1000.000000000000000 ) ; +#13648 = LINE ( 'NONE', #12652, #2883 ) ; +#13649 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75500, 'distance_accuracy_value', 'NONE'); +#13650 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13651 = STYLED_ITEM ( 'NONE', ( #12987 ), #21386 ) ; +#13652 = EDGE_CURVE ( 'NONE', #18075, #86973, #81725, .T. ) ; +#13653 = SURFACE_STYLE_USAGE ( .BOTH. , #83685 ) ; +#13654 = VERTEX_POINT ( 'NONE', #34260 ) ; +#13655 = ORIENTED_EDGE ( 'NONE', *, *, #85595, .F. ) ; +#13656 = AXIS2_PLACEMENT_3D ( 'NONE', #46232, #22803, #54463 ) ; +#13657 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54725 ), #8988 ) ; +#13658 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87297, 'distance_accuracy_value', 'NONE'); +#13659 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999922691396, 0.1200000000000000094, -0.3250000000000000666 ) ) ; +#13660 = VERTEX_POINT ( 'NONE', #65360 ) ; +#13661 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#13663 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01085786437626902988, -0.1500000000000000222 ) ) ; +#13662 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90405 ), #51296 ) ; +#13664 = FILL_AREA_STYLE_COLOUR ( '', #73050 ) ; +#13665 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#13666 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13667 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, -3.499999999999980016, 0.1829999999999999960 ) ) ; +#13668 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13669 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13670 = CARTESIAN_POINT ( 'NONE', ( -1.251886425446270046, -0.9762538161110789758, 0.8299999999999999600 ) ) ; +#13672 = ORIENTED_EDGE ( 'NONE', *, *, #48900, .T. ) ; +#13671 = EDGE_LOOP ( 'NONE', ( #100884, #45432, #10407, #61618 ) ) ; +#13673 = VECTOR ( 'NONE', #30532, 1000.000000000000000 ) ; +#13674 = ORIENTED_EDGE ( 'NONE', *, *, #45421, .F. ) ; +#13675 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#13676 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44695 ), #34995 ) ; +#13678 = LINE ( 'NONE', #14196, #46285 ) ; +#13677 = FILL_AREA_STYLE_COLOUR ( '', #63670 ) ; +#13679 = VECTOR ( 'NONE', #5551, 1000.000000000000114 ) ; +#13680 = VERTEX_POINT ( 'NONE', #3600 ) ; +#13681 = EDGE_LOOP ( 'NONE', ( #177, #25067, #92344, #66843 ) ) ; +#13682 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#13683 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01499999999999998730, -0.1400000000000000688 ) ) ; +#13684 = STYLED_ITEM ( 'NONE', ( #57993 ), #68095 ) ; +#13686 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13685 = SURFACE_SIDE_STYLE ('',( #83215 ) ) ; +#13687 = SURFACE_SIDE_STYLE ('',( #83717 ) ) ; +#13688 = ORIENTED_EDGE ( 'NONE', *, *, #5178, .T. ) ; +#13689 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13690 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13691 = EDGE_CURVE ( 'NONE', #90194, #69225, #27098, .T. ) ; +#13692 = VERTEX_POINT ( 'NONE', #88859 ) ; +#13693 = PLANE ( 'NONE', #83548 ) ; +#13694 = SURFACE_STYLE_USAGE ( .BOTH. , #21420 ) ; +#13695 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96316 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93242, #37667, #53489 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13697 = ORIENTED_EDGE ( 'NONE', *, *, #65354, .T. ) ; +#13696 = PRESENTATION_STYLE_ASSIGNMENT (( #39246 ) ) ; +#13698 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#13699 = FILL_AREA_STYLE ('',( #52589 ) ) ; +#13700 = VECTOR ( 'NONE', #68800, 1000.000000000000000 ) ; +#13701 = SURFACE_STYLE_USAGE ( .BOTH. , #83731 ) ; +#13702 = VECTOR ( 'NONE', #23050, 1000.000000000000000 ) ; +#13703 = ORIENTED_EDGE ( 'NONE', *, *, #29199, .T. ) ; +#13704 = LINE ( 'NONE', #22429, #97369 ) ; +#13705 = ORIENTED_EDGE ( 'NONE', *, *, #71540, .F. ) ; +#13706 = ORIENTED_EDGE ( 'NONE', *, *, #8556, .T. ) ; +#13707 = EDGE_CURVE ( 'NONE', #28002, #100489, #58259, .T. ) ; +#13708 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13709 = EDGE_CURVE ( 'NONE', #79954, #42279, #4573, .T. ) ; +#13710 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13711 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79018 ), #96913 ) ; +#13712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13713 = PRESENTATION_STYLE_ASSIGNMENT (( #67393 ) ) ; +#13714 = EDGE_CURVE ( 'NONE', #99146, #38496, #59775, .T. ) ; +#13715 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13716 = VECTOR ( 'NONE', #11792, 1000.000000000000000 ) ; +#13717 = FILL_AREA_STYLE_COLOUR ( '', #52673 ) ; +#13718 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #15621, #58404 ), + ( #90502, #82853 ), + ( #5692, #21555 ), + ( #3734, #35420 ), + ( #74191, #4724 ), + ( #81381, #74698 ), + ( #20550, #51725 ), + ( #67999, #35907 ), + ( #11301, #34907 ), + ( #81867, #11799 ), + ( #99075, #44036 ), + ( #59909, #73685 ), + ( #82362, #66026 ), + ( #97135, #5194 ), + ( #36397, #27246 ), + ( #67499, #19557 ), + ( #50732, #43036 ), + ( #12318, #4239 ), + ( #28715, #66520 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06708277866639980602, 0.1312050869553290089, 0.1936380489846220021, 0.2553952748861270106, 0.3156922506608579870, 0.3746284903380590059, 0.4337407605315150017, 0.4928056895021890038, 0.5524831251440259772, 0.6123277341640710469, 0.6742432914735759786, 0.7378744975112899729, 0.8023045573449909540, 0.8673918161681599681, 0.9329440335921600491, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#13719 = PLANE ( 'NONE', #1963 ) ; +#13720 = SURFACE_STYLE_FILL_AREA ( #37781 ) ; +#13721 = CARTESIAN_POINT ( 'NONE', ( 0.1711848682203470362, -1.102962211187280106, 0.8300000000000020695 ) ) ; +#13722 = EDGE_LOOP ( 'NONE', ( #61504, #6513, #80816, #51211, #59984, #76938 ) ) ; +#13723 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#13724 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#13725 = ORIENTED_EDGE ( 'NONE', *, *, #21959, .F. ) ; +#13726 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13727 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#13729 = EDGE_CURVE ( 'NONE', #47396, #64967, #14713, .T. ) ; +#13728 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#13730 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30101 ), #51279 ) ; +#13731 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48975 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27402, #89683, #84027 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13732 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13733 = VECTOR ( 'NONE', #51148, 1000.000000000000000 ) ; +#13734 = CARTESIAN_POINT ( 'NONE', ( 1.749115224440590088, -1.150470459123589917, 0.8299999999999999600 ) ) ; +#13735 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13736 = SURFACE_SIDE_STYLE ('',( #61302 ) ) ; +#13737 = CARTESIAN_POINT ( 'NONE', ( -1.263740750452060135, -1.495173285438690103, 0.8300000000000024025 ) ) ; +#13738 = EDGE_CURVE ( 'NONE', #100648, #80884, #69377, .T. ) ; +#13740 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25286 ) ) ; +#13739 = VECTOR ( 'NONE', #91111, 1000.000000000000000 ) ; +#13741 = VECTOR ( 'NONE', #31521, 1000.000000000000000 ) ; +#13742 = SURFACE_STYLE_USAGE ( .BOTH. , #21456 ) ; +#13743 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.449999999999999956, 0.000000000000000000 ) ) ; +#13744 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#13745 = DIRECTION ( 'NONE', ( -0.7071090539100487460, -0.7071045084557415761, 0.000000000000000000 ) ) ; +#13746 = VECTOR ( 'NONE', #17688, 1000.000000000000000 ) ; +#13747 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13748 = EDGE_CURVE ( 'NONE', #16343, #86094, #13176, .T. ) ; +#13750 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13749 = FILL_AREA_STYLE_COLOUR ( '', #39335 ) ; +#13751 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13752 = VECTOR ( 'NONE', #90225, 1000.000000000000000 ) ; +#13753 = VECTOR ( 'NONE', #21557, 1000.000000000000000 ) ; +#13754 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80823, 'distance_accuracy_value', 'NONE'); +#13755 = ORIENTED_EDGE ( 'NONE', *, *, #86523, .F. ) ; +#13756 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#13757 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13758 = SURFACE_STYLE_USAGE ( .BOTH. , #92411 ) ; +#13759 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70579 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90087, #27839, #28805 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13761 = VECTOR ( 'NONE', #89006, 1000.000000000000000 ) ; +#13762 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#13763 = EDGE_CURVE ( 'NONE', #11053, #82073, #99427, .T. ) ; +#13764 = ORIENTED_EDGE ( 'NONE', *, *, #19569, .T. ) ; +#13765 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13766 = AXIS2_PLACEMENT_3D ( 'NONE', #18675, #25879, #96773 ) ; +#13767 = VERTEX_POINT ( 'NONE', #44867 ) ; +#13768 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#13769 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#13770 = FILL_AREA_STYLE_COLOUR ( '', #7340 ) ; +#13771 = PLANE ( 'NONE', #20066 ) ; +#13772 = SURFACE_STYLE_USAGE ( .BOTH. , #98511 ) ; +#13773 = PLANE ( 'NONE', #48205 ) ; +#13774 = AXIS2_PLACEMENT_3D ( 'NONE', #41607, #61699, #61202 ) ; +#13775 = LINE ( 'NONE', #19989, #94066 ) ; +#13776 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13777 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#13778 = FACE_OUTER_BOUND ( 'NONE', #30547, .T. ) ; +#13779 = ORIENTED_EDGE ( 'NONE', *, *, #55035, .T. ) ; +#13780 = EDGE_CURVE ( 'NONE', #33480, #17592, #90866, .T. ) ; +#13781 = SURFACE_STYLE_USAGE ( .BOTH. , #82796 ) ; +#13782 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13783 = ORIENTED_EDGE ( 'NONE', *, *, #40650, .T. ) ; +#13784 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.000000000000000000 ) ) ; +#13785 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30150 ), #51414 ) ; +#13786 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13787 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.266666666666653285, 3.495651678170078205E-76 ) ) ; +#13788 = ORIENTED_EDGE ( 'NONE', *, *, #981, .F. ) ; +#13789 = EDGE_CURVE ( 'NONE', #96899, #25853, #29573, .T. ) ; +#13790 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92335 ), #26924 ) ; +#13791 = STYLED_ITEM ( 'NONE', ( #36716 ), #48258 ) ; +#13792 = STYLED_ITEM ( 'NONE', ( #91005 ), #26938 ) ; +#13793 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#13794 = LINE ( 'NONE', #90966, #10333 ) ; +#13795 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#13796 = EDGE_CURVE ( 'NONE', #57374, #81798, #91362, .T. ) ; +#13798 = ORIENTED_EDGE ( 'NONE', *, *, #90677, .T. ) ; +#13797 = EDGE_LOOP ( 'NONE', ( #96979, #55374, #89607, #13798 ) ) ; +#13799 = FILL_AREA_STYLE ('',( #100500 ) ) ; +#13800 = ORIENTED_EDGE ( 'NONE', *, *, #68572, .T. ) ; +#13801 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61536 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89319, #2041, #26539 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13802 = LINE ( 'NONE', #37859, #61200 ) ; +#13803 = ORIENTED_EDGE ( 'NONE', *, *, #22574, .F. ) ; +#13804 = ORIENTED_EDGE ( 'NONE', *, *, #81604, .T. ) ; +#13807 = VECTOR ( 'NONE', #99805, 1000.000000000000000 ) ; +#13806 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11235 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21543, #14839, #84342 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13808 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82334 ) ) ; +#13809 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13810 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13812 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#13811 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#13813 = VERTEX_POINT ( 'NONE', #21915 ) ; +#13814 = VERTEX_POINT ( 'NONE', #29086 ) ; +#13815 = EDGE_LOOP ( 'NONE', ( #7440, #26754, #88735, #13590 ) ) ; +#13816 = EDGE_CURVE ( 'NONE', #37710, #70520, #82706, .T. ) ; +#13817 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75114 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28859, #29372, #44665 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13818 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2808578643762706939, 0.1500000000000000222 ) ) ; +#13820 = EDGE_LOOP ( 'NONE', ( #51668, #78238, #47631, #97857 ) ) ; +#13819 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8648700000000000276 ) ) ; +#13821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39988 ) ) ; +#13822 = LINE ( 'NONE', #36878, #27876 ) ; +#13823 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13824 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#13825 = SURFACE_SIDE_STYLE ('',( #64 ) ) ; +#13826 = ORIENTED_EDGE ( 'NONE', *, *, #21441, .T. ) ; +#13827 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#13828 = ORIENTED_EDGE ( 'NONE', *, *, #88442, .F. ) ; +#13829 = EDGE_CURVE ( 'NONE', #88364, #73573, #36746, .T. ) ; +#13830 = LINE ( 'NONE', #53707, #46445 ) ; +#13831 = ADVANCED_FACE ( 'NONE', ( #51597 ), #75060, .F. ) ; +#13832 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#13833 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77286 ) ) ; +#13834 = VECTOR ( 'NONE', #66890, 1000.000000000000000 ) ; +#13836 = VERTEX_POINT ( 'NONE', #30062 ) ; +#13835 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13837 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#13839 = CARTESIAN_POINT ( 'NONE', ( 1.502791041020159923, -1.377680218341670093, 0.8100000000000000533 ) ) ; +#13838 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#13840 = CARTESIAN_POINT ( 'NONE', ( -1.200766005632217137, -1.141426888289827302, 0.8099999999998839240 ) ) ; +#13841 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38330 ) ) ; +#13842 = PRESENTATION_STYLE_ASSIGNMENT (( #68003 ) ) ; +#13843 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6482 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31883, #1235, #17540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13844 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13845 = ORIENTED_EDGE ( 'NONE', *, *, #27930, .T. ) ; +#13846 = CARTESIAN_POINT ( 'NONE', ( 9.641736750250085919, 8.392539249749912500, 0.8648700000000000276 ) ) ; +#13847 = LINE ( 'NONE', #60902, #59797 ) ; +#13848 = EDGE_CURVE ( 'NONE', #12872, #20389, #61256, .T. ) ; +#13849 = STYLED_ITEM ( 'NONE', ( #99140 ), #89850 ) ; +#13850 = VECTOR ( 'NONE', #80634, 1000.000000000000000 ) ; +#13851 = SURFACE_STYLE_FILL_AREA ( #54765 ) ; +#13853 = FILL_AREA_STYLE_COLOUR ( '', #8258 ) ; +#13852 = CARTESIAN_POINT ( 'NONE', ( 0.4671228747608590082, -1.059049811218969905, 0.8299999999999999600 ) ) ; +#13854 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13856 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19612 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17124, #78920, #48812 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13855 = SURFACE_STYLE_USAGE ( .BOTH. , #97639 ) ; +#13857 = EDGE_CURVE ( 'NONE', #24092, #24841, #40790, .T. ) ; +#13858 = CIRCLE ( 'NONE', #48111, 0.009999999999999998473 ) ; +#13859 = VECTOR ( 'NONE', #620, 1000.000000000000000 ) ; +#13860 = VECTOR ( 'NONE', #79844, 1000.000000000000114 ) ; +#13861 = VERTEX_POINT ( 'NONE', #8007 ) ; +#13862 = AXIS2_PLACEMENT_3D ( 'NONE', #65728, #89206, #96827 ) ; +#13863 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74284 ), #77543 ) ; +#13864 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.500000000000000000, 9.346759736271676912E-79 ) ) ; +#13865 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13866 = ORIENTED_EDGE ( 'NONE', *, *, #38825, .F. ) ; +#13868 = SURFACE_SIDE_STYLE ('',( #82876 ) ) ; +#13867 = VECTOR ( 'NONE', #33232, 999.9999999999998863 ) ; +#13869 = EDGE_CURVE ( 'NONE', #9760, #7027, #7007, .T. ) ; +#13871 = SURFACE_STYLE_FILL_AREA ( #83878 ) ; +#13870 = LINE ( 'NONE', #76207, #55637 ) ; +#13872 = PRESENTATION_STYLE_ASSIGNMENT (( #5725 ) ) ; +#13873 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13874 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13875 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48215 ) ) ; +#13877 = ORIENTED_EDGE ( 'NONE', *, *, #9682, .F. ) ; +#13878 = SURFACE_STYLE_USAGE ( .BOTH. , #22094 ) ; +#13879 = FILL_AREA_STYLE_COLOUR ( '', #26744 ) ; +#13880 = DIRECTION ( 'NONE', ( -0.3438200982495990266, 0.000000000000000000, 0.9390355371548171348 ) ) ; +#13881 = VECTOR ( 'NONE', #7666, 1000.000000000000000 ) ; +#13882 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13883 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30119 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49248, #72719, #65063 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13884 = SURFACE_STYLE_FILL_AREA ( #7196 ) ; +#13885 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#13886 = SURFACE_SIDE_STYLE ('',( #74734 ) ) ; +#13887 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#13888 = SURFACE_SIDE_STYLE ('',( #85895 ) ) ; +#13889 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#13890 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13891 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37276 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58406, #1747, #11801 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13892 = VECTOR ( 'NONE', #98115, 1000.000000000000000 ) ; +#13893 = EDGE_CURVE ( 'NONE', #34839, #42279, #54073, .T. ) ; +#13894 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13895 = ORIENTED_EDGE ( 'NONE', *, *, #43962, .T. ) ; +#13896 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, -0.1400000000000000133 ) ) ; +#13897 = ORIENTED_EDGE ( 'NONE', *, *, #99939, .T. ) ; +#13898 = VECTOR ( 'NONE', #20034, 1000.000000000000000 ) ; +#13899 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13900 = CARTESIAN_POINT ( 'NONE', ( 1.059879982250959918, -1.052467830684129968, 0.8100000000000000533 ) ) ; +#13901 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#13902 = STYLED_ITEM ( 'NONE', ( #50195 ), #12723 ) ; +#13903 = PLANE ( 'NONE', #42348 ) ; +#13904 = CARTESIAN_POINT ( 'NONE', ( 1.702357802111380103, -0.9001170352889870108, 0.8299999999999999600 ) ) ; +#13905 = LINE ( 'NONE', #61460, #66356 ) ; +#13906 = LINE ( 'NONE', #21124, #43915 ) ; +#13907 = SURFACE_SIDE_STYLE ('',( #68571 ) ) ; +#13908 = VERTEX_POINT ( 'NONE', #40275 ) ; +#13909 = EDGE_CURVE ( 'NONE', #57121, #84102, #22181, .T. ) ; +#13910 = PRESENTATION_STYLE_ASSIGNMENT (( #44105 ) ) ; +#13911 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13912 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#13913 = ORIENTED_EDGE ( 'NONE', *, *, #93138, .F. ) ; +#13914 = FACE_OUTER_BOUND ( 'NONE', #54204, .T. ) ; +#13915 = ADVANCED_FACE ( 'NONE', ( #39757, #55610, #47411 ), #18636, .F. ) ; +#13916 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48411 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76058, #13708, #60767 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13917 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -4.344024262657780003E-34 ) ) ; +#13918 = AXIS2_PLACEMENT_3D ( 'NONE', #52603, #99932, #5573 ) ; +#13919 = SURFACE_SIDE_STYLE ('',( #4798 ) ) ; +#13920 = SURFACE_SIDE_STYLE ('',( #45090 ) ) ; +#13921 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#13922 = EDGE_CURVE ( 'NONE', #38846, #10900, #950, .T. ) ; +#13923 = ORIENTED_EDGE ( 'NONE', *, *, #88408, .F. ) ; +#13924 = FILL_AREA_STYLE ('',( #91579 ) ) ; +#13925 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#13926 = FILL_AREA_STYLE ('',( #75769 ) ) ; +#13927 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#13928 = VECTOR ( 'NONE', #53342, 1000.000000000000000 ) ; +#13929 = AXIS2_PLACEMENT_3D ( 'NONE', #56534, #86629, #87640 ) ; +#13930 = VECTOR ( 'NONE', #2389, 1000.000000000000000 ) ; +#13931 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45003 ) ) ; +#13932 = VERTEX_POINT ( 'NONE', #62753 ) ; +#13933 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66116 ), #71134 ) ; +#13934 = VECTOR ( 'NONE', #44557, 1000.000000000000000 ) ; +#13935 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#13936 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.6999999999999999556, -13.35000000000000142 ) ) ; +#13937 = SURFACE_STYLE_USAGE ( .BOTH. , #99174 ) ; +#13938 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#13939 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13940 = CIRCLE ( 'NONE', #71067, 0.009999999999999998473 ) ; +#13941 = CARTESIAN_POINT ( 'NONE', ( 1.631872624588970089, -1.500900992704750081, 0.8300000000000001821 ) ) ; +#13942 = ORIENTED_EDGE ( 'NONE', *, *, #99917, .F. ) ; +#13943 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#13945 = EDGE_CURVE ( 'NONE', #34253, #79146, #46378, .T. ) ; +#13944 = PRODUCT ( 'C0201_20210301.xtd', 'C0201_20210301.xtd', '', ( #72375 ) ) ; +#13946 = EDGE_CURVE ( 'NONE', #13552, #48204, #16736, .T. ) ; +#13947 = AXIS2_PLACEMENT_3D ( 'NONE', #61301, #31132, #99949 ) ; +#13948 = ORIENTED_EDGE ( 'NONE', *, *, #36182, .F. ) ; +#13949 = ADVANCED_FACE ( 'NONE', ( #23431 ), #7508, .T. ) ; +#13951 = ORIENTED_EDGE ( 'NONE', *, *, #75492, .F. ) ; +#13950 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#13953 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16814, #54151, #92901 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#13952 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42030, 'distance_accuracy_value', 'NONE'); +#13954 = FILL_AREA_STYLE ('',( #45113 ) ) ; +#13955 = CARTESIAN_POINT ( 'NONE', ( -1.284259234833809993, -1.485874691073119980, 0.8100000000000000533 ) ) ; +#13956 = PRESENTATION_STYLE_ASSIGNMENT (( #83954 ) ) ; +#13958 = VECTOR ( 'NONE', #75628, 1000.000000000000000 ) ; +#13957 = LINE ( 'NONE', #187, #21049 ) ; +#13959 = ORIENTED_EDGE ( 'NONE', *, *, #77508, .T. ) ; +#13960 = LINE ( 'NONE', #13425, #11253 ) ; +#13961 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#13962 = VERTEX_POINT ( 'NONE', #43628 ) ; +#13963 = STYLED_ITEM ( 'NONE', ( #39833 ), #99455 ) ; +#13964 = SURFACE_STYLE_USAGE ( .BOTH. , #100169 ) ; +#13965 = VERTEX_POINT ( 'NONE', #97243 ) ; +#13967 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#13966 = SURFACE_STYLE_FILL_AREA ( #12933 ) ; +#13968 = EDGE_LOOP ( 'NONE', ( #24691, #15696, #94986, #2433, #88476, #47890 ) ) ; +#13969 = EDGE_CURVE ( 'NONE', #37874, #28448, #67122, .T. ) ; +#13970 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58094 ) ) ; +#13971 = VECTOR ( 'NONE', #92348, 1000.000000000000000 ) ; +#13973 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13972 = LINE ( 'NONE', #52836, #80537 ) ; +#13974 = LINE ( 'NONE', #28351, #62101 ) ; +#13975 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#13976 = CARTESIAN_POINT ( 'NONE', ( 0.2602800372128030171, -1.290215378870249952, 0.8299999999999992939 ) ) ; +#13977 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80829 ), #7457 ) ; +#13978 = ORIENTED_EDGE ( 'NONE', *, *, #88012, .F. ) ; +#13979 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999993616, 0.8199999999999998401, 0.04999999999999994726 ) ) ; +#13980 = ORIENTED_EDGE ( 'NONE', *, *, #5769, .T. ) ; +#13981 = DIRECTION ( 'NONE', ( 0.7071067811865489050, 0.7071067811865462405, 0.000000000000000000 ) ) ; +#13982 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #80459, #41154, #79962, #35017 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#13984 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#13983 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#13985 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000011470, -1.979898987322330051, 0.6999285677838846809 ) ) ; +#13986 = SURFACE_STYLE_FILL_AREA ( #36043 ) ; +#13987 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#13988 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#13989 = LINE ( 'NONE', #38034, #18163 ) ; +#13990 = SURFACE_SIDE_STYLE ('',( #30333 ) ) ; +#13991 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#13992 = PLANE ( 'NONE', #34121 ) ; +#13993 = EDGE_LOOP ( 'NONE', ( #4731, #30545, #41523, #61736 ) ) ; +#13994 = LINE ( 'NONE', #5835, #85587 ) ; +#13995 = EDGE_CURVE ( 'NONE', #49575, #7027, #5301, .T. ) ; +#13997 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#13996 = PLANE ( 'NONE', #44086 ) ; +#13998 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39858, 'distance_accuracy_value', 'NONE'); +#13999 = PRESENTATION_STYLE_ASSIGNMENT (( #77326 ) ) ; +#14000 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14001 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34106 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58072, #98258, #50894 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14002 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74342 ), #49945 ) ; +#14003 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.383333333333330195, 0.000000000000000000 ) ) ; +#14004 = EDGE_CURVE ( 'NONE', #64495, #53923, #97720, .T. ) ; +#14005 = SURFACE_SIDE_STYLE ('',( #84010 ) ) ; +#14006 = ORIENTED_EDGE ( 'NONE', *, *, #19411, .F. ) ; +#14007 = FILL_AREA_STYLE_COLOUR ( '', #11289 ) ; +#14008 = STYLED_ITEM ( 'NONE', ( #83868 ), #61517 ) ; +#14009 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14010 = VECTOR ( 'NONE', #68622, 1000.000000000000000 ) ; +#14011 = CARTESIAN_POINT ( 'NONE', ( -0.07646240217796579364, -1.441250752426249893, 0.8100000000000000533 ) ) ; +#14012 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8648700000000000276 ) ) ; +#14013 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, -0.02000000000002305142 ) ) ; +#14014 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79307 ) ) ; +#14015 = CIRCLE ( 'NONE', #27147, 0.2500000000000000000 ) ; +#14016 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14017 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#14018 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14019 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14020 = FILL_AREA_STYLE_COLOUR ( '', #45233 ) ; +#14021 = FILL_AREA_STYLE ('',( #14527 ) ) ; +#14022 = ADVANCED_FACE ( 'NONE', ( #26849 ), #3837, .T. ) ; +#14023 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14024 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95601 ) ) ; +#14025 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14026 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#14027 = SURFACE_STYLE_FILL_AREA ( #28893 ) ; +#14028 = DIRECTION ( 'NONE', ( 2.824738166141190008E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14029 = SURFACE_STYLE_FILL_AREA ( #99263 ) ; +#14030 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#14031 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14032 = FILL_AREA_STYLE ('',( #29407 ) ) ; +#14033 = PRESENTATION_STYLE_ASSIGNMENT (( #92179 ) ) ; +#14034 = ORIENTED_EDGE ( 'NONE', *, *, #36182, .T. ) ; +#14035 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#14036 = EDGE_CURVE ( 'NONE', #54843, #76430, #89615, .T. ) ; +#14037 = VECTOR ( 'NONE', #93651, 1000.000000000000000 ) ; +#14038 = CARTESIAN_POINT ( 'NONE', ( 3.666684875124987197, 7.848067124875013789, 0.8991599999999999593 ) ) ; +#14039 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14040 = CARTESIAN_POINT ( 'NONE', ( -1.723820061220085353, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#14041 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66215 ), #35279 ) ; +#14042 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41480 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38502, #45117, #37513 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14043 = LINE ( 'NONE', #29906, #34788 ) ; +#14044 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, 0.000000000000000000 ) ) ; +#14045 = PLANE ( 'NONE', #55383 ) ; +#14046 = SURFACE_STYLE_USAGE ( .BOTH. , #52922 ) ; +#14047 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#14048 = EDGE_CURVE ( 'NONE', #53678, #46008, #12342, .T. ) ; +#14049 = VERTEX_POINT ( 'NONE', #28339 ) ; +#14050 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#14051 = LINE ( 'NONE', #13526, #67071 ) ; +#14052 = EDGE_CURVE ( 'NONE', #43011, #46344, #81488, .T. ) ; +#14053 = SURFACE_SIDE_STYLE ('',( #28431 ) ) ; +#14054 = VERTEX_POINT ( 'NONE', #12425 ) ; +#14055 = VERTEX_POINT ( 'NONE', #90621 ) ; +#14056 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #57840, #50177, #74129, #10224 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14057 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#14059 = FILL_AREA_STYLE ('',( #28924 ) ) ; +#14058 = CARTESIAN_POINT ( 'NONE', ( 0.4656308297546359887, -1.047495427385189970, 0.8300000000000002931 ) ) ; +#14060 = ORIENTED_EDGE ( 'NONE', *, *, #54343, .F. ) ; +#14061 = FACE_OUTER_BOUND ( 'NONE', #18986, .T. ) ; +#14062 = CARTESIAN_POINT ( 'NONE', ( 0.05811896311769199769, -1.438073744133560039, 0.8100000000000000533 ) ) ; +#14063 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98280 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86, #92976, #6672 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14064 = CARTESIAN_POINT ( 'NONE', ( 0.5010457827341869841, -1.198290873665909917, 0.8299999999999999600 ) ) ; +#14065 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14066 = FACE_OUTER_BOUND ( 'NONE', #15288, .T. ) ; +#14067 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000020206, 0.1829999999999619986 ) ) ; +#14068 = ADVANCED_FACE ( 'NONE', ( #80976 ), #82473, .F. ) ; +#14069 = EDGE_CURVE ( 'NONE', #38629, #46126, #39007, .T. ) ; +#14070 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #7674, #82894 ) ; +#14071 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14072 = VECTOR ( 'NONE', #38413, 1000.000000000000000 ) ; +#14073 = ORIENTED_EDGE ( 'NONE', *, *, #19190, .T. ) ; +#14074 = EDGE_CURVE ( 'NONE', #18774, #30322, #61506, .T. ) ; +#14075 = ORIENTED_EDGE ( 'NONE', *, *, #39460, .F. ) ; +#14076 = EDGE_CURVE ( 'NONE', #59144, #27071, #38241, .T. ) ; +#14077 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14078 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#14079 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90200 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67181, #67664, #10972 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14080 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77753 ), #10840 ) ; +#14081 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68799, 'distance_accuracy_value', 'NONE'); +#14082 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#14083 = FILL_AREA_STYLE_COLOUR ( '', #65933 ) ; +#14084 = CIRCLE ( 'NONE', #82591, 0.1679250012421869831 ) ; +#14085 = EDGE_CURVE ( 'NONE', #51979, #30306, #85786, .T. ) ; +#14086 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -1.626303258728260102E-16 ) ) ; +#14087 = EDGE_LOOP ( 'NONE', ( #11687, #99940, #48050, #91485 ) ) ; +#14089 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#14088 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14090 = VERTEX_POINT ( 'NONE', #46117 ) ; +#14091 = ORIENTED_EDGE ( 'NONE', *, *, #53778, .T. ) ; +#14092 = CARTESIAN_POINT ( 'NONE', ( 1.303722762681589931, -1.254158608853950030, 0.8299999999999999600 ) ) ; +#14093 = EDGE_CURVE ( 'NONE', #88040, #72506, #21669, .T. ) ; +#14094 = AXIS2_PLACEMENT_3D ( 'NONE', #45832, #31566, #69846 ) ; +#14096 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14095 = SURFACE_SIDE_STYLE ('',( #29464 ) ) ; +#14097 = PRESENTATION_STYLE_ASSIGNMENT (( #54477 ) ) ; +#14098 = AXIS2_PLACEMENT_3D ( 'NONE', #32778, #8192, #46563 ) ; +#14100 = VERTEX_POINT ( 'NONE', #93080 ) ; +#14099 = PRESENTATION_STYLE_ASSIGNMENT (( #91248 ) ) ; +#14101 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14102 = FILL_AREA_STYLE_COLOUR ( '', #8118 ) ; +#14103 = EDGE_LOOP ( 'NONE', ( #86544, #42809, #86559, #84818 ) ) ; +#14104 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14105 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14106 = EDGE_LOOP ( 'NONE', ( #22795, #60655, #30174, #15937 ) ) ; +#14107 = ORIENTED_EDGE ( 'NONE', *, *, #2837, .T. ) ; +#14108 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#14109 = CLOSED_SHELL ( 'NONE', ( #64426, #62848, #94344, #7477, #18136, #59991 ) ) ; +#14110 = CARTESIAN_POINT ( 'NONE', ( 0.9590361231611750359, -1.326636125966530244, 0.8100000000000000533 ) ) ; +#14111 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14112 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#14113 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#14114 = VECTOR ( 'NONE', #60951, 1000.000000000000000 ) ; +#14115 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#14116 = PRESENTATION_STYLE_ASSIGNMENT (( #22841 ) ) ; +#14117 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#14118 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32108 ), #50068 ) ; +#14119 = PRESENTATION_STYLE_ASSIGNMENT (( #45767 ) ) ; +#14120 = VECTOR ( 'NONE', #79204, 1000.000000000000000 ) ; +#14121 = ORIENTED_EDGE ( 'NONE', *, *, #68160, .T. ) ; +#14122 = ORIENTED_EDGE ( 'NONE', *, *, #74304, .T. ) ; +#14123 = SURFACE_STYLE_USAGE ( .BOTH. , #84119 ) ; +#14124 = CARTESIAN_POINT ( 'NONE', ( -0.01942805220116449946, -1.009819306370540071, 0.8299999999999999600 ) ) ; +#14125 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14127 = STYLED_ITEM ( 'NONE', ( #97108 ), #13344 ) ; +#14126 = LINE ( 'NONE', #45279, #90464 ) ; +#14128 = PLANE ( 'NONE', #66628 ) ; +#14129 = SURFACE_SIDE_STYLE ('',( #36183 ) ) ; +#14130 = ADVANCED_FACE ( 'NONE', ( #54330 ), #53327, .F. ) ; +#14131 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14132 = ORIENTED_EDGE ( 'NONE', *, *, #8047, .F. ) ; +#14133 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#14134 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14135 = FILL_AREA_STYLE ('',( #84133 ) ) ; +#14136 = SURFACE_STYLE_USAGE ( .BOTH. , #37191 ) ; +#14137 = PRESENTATION_STYLE_ASSIGNMENT (( #100333 ) ) ; +#14138 = STYLED_ITEM ( 'NONE', ( #65852 ), #34291 ) ; +#14139 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14140 = VECTOR ( 'NONE', #94395, 1000.000000000000000 ) ; +#14141 = CARTESIAN_POINT ( 'NONE', ( 1.894788238603390296, -1.280379325981960026, 0.8100000000000000533 ) ) ; +#14142 = LINE ( 'NONE', #69267, #58913 ) ; +#14143 = LINE ( 'NONE', #98862, #23682 ) ; +#14144 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41911 ) ) ; +#14145 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14146 = LINE ( 'NONE', #83654, #60147 ) ; +#14147 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14148 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14149 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14150 = FILL_AREA_STYLE ('',( #84150 ) ) ; +#14151 = LINE ( 'NONE', #53522, #39465 ) ; +#14152 = ORIENTED_EDGE ( 'NONE', *, *, #53618, .F. ) ; +#14153 = FILL_AREA_STYLE_COLOUR ( '', #70698 ) ; +#14154 = VECTOR ( 'NONE', #67662, 1000.000000000000000 ) ; +#14155 = ADVANCED_FACE ( 'NONE', ( #14466 ), #99665, .F. ) ; +#14156 = CARTESIAN_POINT ( 'NONE', ( 1.580074546203000141, -1.378252124432310044, 0.8299999999999977396 ) ) ; +#14157 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#14159 = FILL_AREA_STYLE ('',( #84159 ) ) ; +#14158 = AXIS2_PLACEMENT_3D ( 'NONE', #67506, #57391, #66527 ) ; +#14160 = PRESENTATION_STYLE_ASSIGNMENT (( #12638 ) ) ; +#14161 = SURFACE_STYLE_USAGE ( .BOTH. , #60696 ) ; +#14162 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48501 ), #84332 ) ; +#14163 = LINE ( 'NONE', #68324, #9058 ) ; +#14164 = ORIENTED_EDGE ( 'NONE', *, *, #64516, .T. ) ; +#14165 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10929 ), #48506 ) ; +#14166 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14167 = SURFACE_SIDE_STYLE ('',( #46335 ) ) ; +#14168 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14169 = VECTOR ( 'NONE', #32196, 1000.000000000000000 ) ; +#14170 = CLOSED_SHELL ( 'NONE', ( #99710, #12583, #97666, #86498, #11496, #90904 ) ) ; +#14171 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93112, #60045, #52370, #82994 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14173 = VECTOR ( 'NONE', #99708, 1000.000000000000000 ) ; +#14172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14174 = EDGE_LOOP ( 'NONE', ( #41666, #8345, #37638, #98946 ) ) ; +#14175 = ORIENTED_EDGE ( 'NONE', *, *, #40909, .T. ) ; +#14176 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#14177 = ORIENTED_EDGE ( 'NONE', *, *, #74652, .F. ) ; +#14178 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#14179 = PRESENTATION_STYLE_ASSIGNMENT (( #91819 ) ) ; +#14180 = VECTOR ( 'NONE', #42503, 1000.000000000000000 ) ; +#14181 = SURFACE_STYLE_USAGE ( .BOTH. , #28549 ) ; +#14182 = FILL_AREA_STYLE_COLOUR ( '', #84183 ) ; +#14183 = CARTESIAN_POINT ( 'NONE', ( 7.739619127034740309, 10.45022087296526259, 0.8991599999999999593 ) ) ; +#14184 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98912 ) ) ; +#14185 = FACE_OUTER_BOUND ( 'NONE', #86193, .T. ) ; +#14186 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #65775 ) ; +#14187 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#14189 = VERTEX_POINT ( 'NONE', #2735 ) ; +#14188 = EDGE_LOOP ( 'NONE', ( #69628, #19261, #78070, #21310, #88875, #21384, #27970, #46392 ) ) ; +#14190 = VERTEX_POINT ( 'NONE', #87482 ) ; +#14191 = EDGE_CURVE ( 'NONE', #15222, #19424, #42929, .T. ) ; +#14192 = SURFACE_STYLE_USAGE ( .BOTH. , #66859 ) ; +#14193 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63554, 'distance_accuracy_value', 'NONE'); +#14194 = SURFACE_STYLE_FILL_AREA ( #84199 ) ; +#14196 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#14195 = LINE ( 'NONE', #62746, #86455 ) ; +#14197 = ORIENTED_EDGE ( 'NONE', *, *, #28902, .T. ) ; +#14198 = ORIENTED_EDGE ( 'NONE', *, *, #83298, .F. ) ; +#14199 = PLANE ( 'NONE', #53148 ) ; +#14200 = SURFACE_SIDE_STYLE ('',( #53070 ) ) ; +#14201 = SURFACE_STYLE_USAGE ( .BOTH. , #84209 ) ; +#14203 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#14202 = LINE ( 'NONE', #19912, #43219 ) ; +#14204 = CARTESIAN_POINT ( 'NONE', ( -0.3840663679600159752, -0.9878352835667890686, 0.8299999999999999600 ) ) ; +#14205 = ORIENTED_EDGE ( 'NONE', *, *, #66789, .F. ) ; +#14206 = PLANE ( 'NONE', #33974 ) ; +#14207 = VERTEX_POINT ( 'NONE', #9788 ) ; +#14208 = ORIENTED_EDGE ( 'NONE', *, *, #58208, .T. ) ; +#14209 = VECTOR ( 'NONE', #90274, 1000.000000000000000 ) ; +#14210 = DIRECTION ( 'NONE', ( 0.9990832187810425591, 0.04281030191567540555, 0.000000000000000000 ) ) ; +#14212 = ORIENTED_EDGE ( 'NONE', *, *, #61972, .F. ) ; +#14211 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#14213 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14214 = AXIS2_PLACEMENT_3D ( 'NONE', #10849, #20085, #11841 ) ; +#14215 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14216 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#14217 = VERTEX_POINT ( 'NONE', #56879 ) ; +#14218 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#14219 = CARTESIAN_POINT ( 'NONE', ( 3.277775124875012214, 5.988376124875013140, 0.8648700000000000276 ) ) ; +#14220 = VERTEX_POINT ( 'NONE', #48192 ) ; +#14221 = ORIENTED_EDGE ( 'NONE', *, *, #4323, .F. ) ; +#14222 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.7000000000000001776, -0.02000000000000000042 ) ) ; +#14223 = PRESENTATION_STYLE_ASSIGNMENT (( #13200 ) ) ; +#14224 = PRESENTATION_STYLE_ASSIGNMENT (( #5080 ) ) ; +#14225 = PLANE ( 'NONE', #24880 ) ; +#14226 = CARTESIAN_POINT ( 'NONE', ( 1.258996483356980001, -1.238505293396390039, 0.8299999999999997380 ) ) ; +#14227 = EDGE_CURVE ( 'NONE', #7027, #36856, #49202, .T. ) ; +#14228 = SURFACE_STYLE_FILL_AREA ( #91882 ) ; +#14229 = ORIENTED_EDGE ( 'NONE', *, *, #69059, .T. ) ; +#14230 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14231 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66168 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16546, #71716, #1784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14232 = ORIENTED_EDGE ( 'NONE', *, *, #15223, .T. ) ; +#14233 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14234 = VECTOR ( 'NONE', #42099, 1000.000000000000000 ) ; +#14235 = STYLED_ITEM ( 'NONE', ( #55706 ), #16391 ) ; +#14236 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#14237 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14238 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84407 ), #10937 ) ; +#14240 = FILL_AREA_STYLE ('',( #92386 ) ) ; +#14239 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#14241 = LINE ( 'NONE', #86765, #9537 ) ; +#14242 = FACE_OUTER_BOUND ( 'NONE', #76542, .T. ) ; +#14243 = CLOSED_SHELL ( 'NONE', ( #25831, #81871, #62649, #32284, #89864, #83741 ) ) ; +#14244 = EDGE_CURVE ( 'NONE', #43664, #26591, #32365, .T. ) ; +#14245 = PRESENTATION_STYLE_ASSIGNMENT (( #39278 ) ) ; +#14246 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#14247 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#14248 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2527, #48503, #10577 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14249 = VECTOR ( 'NONE', #72307, 1000.000000000000114 ) ; +#14250 = FACE_OUTER_BOUND ( 'NONE', #15398, .T. ) ; +#14251 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14252 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14253 = SURFACE_SIDE_STYLE ('',( #62298 ) ) ; +#14254 = VECTOR ( 'NONE', #67406, 1000.000000000000000 ) ; +#14255 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#14256 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21000 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29474, #21307, #92244 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14257 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14258 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81184 ), #69752 ) ; +#14259 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#14260 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14261 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#14262 = FILL_AREA_STYLE ('',( #98004 ) ) ; +#14263 = AXIS2_PLACEMENT_3D ( 'NONE', #74245, #74748, #18588 ) ; +#14264 = ORIENTED_EDGE ( 'NONE', *, *, #17199, .F. ) ; +#14265 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62484, 'distance_accuracy_value', 'NONE'); +#14266 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33022, 'distance_accuracy_value', 'NONE'); +#14267 = ADVANCED_FACE ( 'NONE', ( #80346 ), #10275, .F. ) ; +#14268 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14269 = LINE ( 'NONE', #98988, #78723 ) ; +#14270 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#14272 = PLANE ( 'NONE', #7443 ) ; +#14271 = AXIS2_PLACEMENT_3D ( 'NONE', #84793, #24058, #54174 ) ; +#14273 = FILL_AREA_STYLE ('',( #85267 ) ) ; +#14274 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#14275 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14276 = EDGE_CURVE ( 'NONE', #74058, #15336, #89508, .T. ) ; +#14277 = LINE ( 'NONE', #36820, #56824 ) ; +#14278 = STYLED_ITEM ( 'NONE', ( #27382 ), #30967 ) ; +#14279 = ORIENTED_EDGE ( 'NONE', *, *, #83396, .F. ) ; +#14280 = EDGE_LOOP ( 'NONE', ( #65321, #99067, #77545, #40894 ) ) ; +#14281 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97076, 'distance_accuracy_value', 'NONE'); +#14282 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63355, 'distance_accuracy_value', 'NONE'); +#14283 = FILL_AREA_STYLE ('',( #100478 ) ) ; +#14284 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#14285 = LINE ( 'NONE', #76123, #33064 ) ; +#14286 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88211 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53899, #85028, #92659 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14287 = VECTOR ( 'NONE', #100092, 1000.000000000000000 ) ; +#14288 = SURFACE_STYLE_USAGE ( .BOTH. , #66958 ) ; +#14289 = PLANE ( 'NONE', #77856 ) ; +#14290 = SURFACE_STYLE_USAGE ( .BOTH. , #84294 ) ; +#14291 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14292 = VERTEX_POINT ( 'NONE', #51214 ) ; +#14293 = EDGE_CURVE ( 'NONE', #18334, #56185, #97125, .T. ) ; +#14294 = ADVANCED_FACE ( 'NONE', ( #67007 ), #73190, .T. ) ; +#14295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14296 = ORIENTED_EDGE ( 'NONE', *, *, #79033, .T. ) ; +#14297 = SURFACE_STYLE_FILL_AREA ( #35856 ) ; +#14298 = SURFACE_SIDE_STYLE ('',( #13262 ) ) ; +#14299 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73036 ) ) ; +#14300 = ORIENTED_EDGE ( 'NONE', *, *, #41555, .F. ) ; +#14301 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14302 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14303 = AXIS2_PLACEMENT_3D ( 'NONE', #26855, #74807, #80984 ) ; +#14304 = CYLINDRICAL_SURFACE ( 'NONE', #77251, 0.6999999999999999556 ) ; +#14305 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14306 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#14307 = AXIS2_PLACEMENT_3D ( 'NONE', #51259, #82409, #43566 ) ; +#14308 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#14309 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14311 = EDGE_LOOP ( 'NONE', ( #8025, #7428, #20755, #77932 ) ) ; +#14310 = ORIENTED_EDGE ( 'NONE', *, *, #85234, .T. ) ; +#14312 = AXIS2_PLACEMENT_3D ( 'NONE', #59679, #35675, #12588 ) ; +#14313 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14314 = EDGE_LOOP ( 'NONE', ( #17012, #95047, #19607, #85597 ) ) ; +#14315 = EDGE_CURVE ( 'NONE', #84098, #89309, #96121, .T. ) ; +#14316 = STYLED_ITEM ( 'NONE', ( #78407 ), #23484 ) ; +#14318 = CARTESIAN_POINT ( 'NONE', ( -0.4617362663480760743, -1.013453039847479920, 0.8299999999999999600 ) ) ; +#14317 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14319 = CLOSED_SHELL ( 'NONE', ( #54704, #98170, #18157, #48092, #97809, #56445 ) ) ; +#14320 = VERTEX_POINT ( 'NONE', #42038 ) ; +#14321 = ORIENTED_EDGE ( 'NONE', *, *, #10882, .F. ) ; +#14322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50534 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85789, #55199, #31173 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14323 = LINE ( 'NONE', #86329, #95461 ) ; +#14324 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14326 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#14325 = SURFACE_SIDE_STYLE ('',( #43503 ) ) ; +#14327 = DIRECTION ( 'NONE', ( 0.7071045084557405769, 0.7071090539100497452, 0.000000000000000000 ) ) ; +#14329 = VERTEX_POINT ( 'NONE', #42540 ) ; +#14328 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#14330 = VERTEX_POINT ( 'NONE', #96624 ) ; +#14331 = FACE_OUTER_BOUND ( 'NONE', #50090, .T. ) ; +#14332 = VERTEX_POINT ( 'NONE', #34893 ) ; +#14333 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35626 ) ) ; +#14334 = ADVANCED_FACE ( 'NONE', ( #19544 ), #89988, .F. ) ; +#14335 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#14338 = ORIENTED_EDGE ( 'NONE', *, *, #52473, .F. ) ; +#14337 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45327 ), #29044 ) ; +#14336 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14339 = FILL_AREA_STYLE ('',( #65126 ) ) ; +#14340 = SURFACE_STYLE_FILL_AREA ( #84341 ) ; +#14341 = SURFACE_STYLE_FILL_AREA ( #29703 ) ; +#14342 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671291000000000082, 0.8648700000000000276 ) ) ; +#14343 = ORIENTED_EDGE ( 'NONE', *, *, #77551, .F. ) ; +#14344 = FACE_OUTER_BOUND ( 'NONE', #94021, .T. ) ; +#14345 = ORIENTED_EDGE ( 'NONE', *, *, #85595, .T. ) ; +#14346 = AXIS2_PLACEMENT_3D ( 'NONE', #100420, #38762, #98090 ) ; +#14347 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.449999999999999956, -11.32000000000000028 ) ) ; +#14348 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14349 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #75948, .NOT_KNOWN. ) ; +#14350 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91008 ), #71478 ) ; +#14351 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58683, #98371, #97412, #58186 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14353 = ORIENTED_EDGE ( 'NONE', *, *, #76, .F. ) ; +#14352 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#14354 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14355 = LINE ( 'NONE', #78216, #82483 ) ; +#14356 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99972 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72712, #96164, #64058 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14357 = CARTESIAN_POINT ( 'NONE', ( -1.056482696342210481, -1.176312577709545337, 0.8099999999998583888 ) ) ; +#14358 = ADVANCED_FACE ( 'NONE', ( #84344 ), #7145, .T. ) ; +#14359 = FILL_AREA_STYLE_COLOUR ( '', #11337 ) ; +#14360 = SURFACE_STYLE_USAGE ( .BOTH. , #99579 ) ; +#14361 = VERTEX_POINT ( 'NONE', #100050 ) ; +#14362 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#14363 = STYLED_ITEM ( 'NONE', ( #15340 ), #56483 ) ; +#14364 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#14365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78048 ), #43779 ) ; +#14366 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.1499999999999999944, 0.08229670385730990245 ) ) ; +#14368 = CARTESIAN_POINT ( 'NONE', ( 1.342015624714327560, -1.401660485983072801, 0.8099999999997371525 ) ) ; +#14367 = CARTESIAN_POINT ( 'NONE', ( 0.4344096565324859771, -0.9919132076701281386, 0.8299999999999999600 ) ) ; +#14369 = FILL_AREA_STYLE_COLOUR ( '', #45059 ) ; +#14370 = EDGE_CURVE ( 'NONE', #25247, #11018, #92959, .T. ) ; +#14371 = VECTOR ( 'NONE', #64698, 1000.000000000000000 ) ; +#14372 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#14373 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97560 ), #27497 ) ; +#14374 = EDGE_CURVE ( 'NONE', #52193, #86944, #66090, .T. ) ; +#14375 = ORIENTED_EDGE ( 'NONE', *, *, #22186, .T. ) ; +#14376 = PLANE ( 'NONE', #90594 ) ; +#14377 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81070 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67872, #43412, #65905 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14378 = VERTEX_POINT ( 'NONE', #6653 ) ; +#14379 = SURFACE_STYLE_FILL_AREA ( #77719 ) ; +#14380 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#14381 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93812 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87669, #56049, #2415 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14383 = SURFACE_STYLE_USAGE ( .BOTH. , #76208 ) ; +#14382 = FACE_OUTER_BOUND ( 'NONE', #57865, .T. ) ; +#14384 = SURFACE_STYLE_FILL_AREA ( #60921 ) ; +#14385 = STYLED_ITEM ( 'NONE', ( #73340 ), #979 ) ; +#14386 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14387 = SURFACE_STYLE_USAGE ( .BOTH. , #16406 ) ; +#14388 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14389 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94295 ) ) ; +#14390 = ORIENTED_EDGE ( 'NONE', *, *, #50154, .F. ) ; +#14391 = PLANE ( 'NONE', #28328 ) ; +#14392 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#14393 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14394 = FACE_OUTER_BOUND ( 'NONE', #85998, .T. ) ; +#14395 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43968 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60186, #31000, #62181 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14396 = CARTESIAN_POINT ( 'NONE', ( -0.4406604980795930104, 0.3469452572770918564, 0.8100000000000000533 ) ) ; +#14397 = ADVANCED_FACE ( 'NONE', ( #83353 ), #68503, .F. ) ; +#14398 = EDGE_CURVE ( 'NONE', #77789, #48436, #67490, .T. ) ; +#14399 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14400 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47880, 'distance_accuracy_value', 'NONE'); +#14401 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1422 ), #37292 ) ; +#14402 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#14403 = ORIENTED_EDGE ( 'NONE', *, *, #63996, .T. ) ; +#14404 = VERTEX_POINT ( 'NONE', #83851 ) ; +#14405 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14406 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94193, 'distance_accuracy_value', 'NONE'); +#14407 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87986, 'distance_accuracy_value', 'NONE'); +#14408 = STYLED_ITEM ( 'NONE', ( #57833 ), #43967 ) ; +#14409 = CARTESIAN_POINT ( 'NONE', ( 1.065702489232140060, -1.018544155089240011, 0.8299999999999999600 ) ) ; +#14410 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#14411 = FILL_AREA_STYLE ('',( #23143 ) ) ; +#14412 = CARTESIAN_POINT ( 'NONE', ( 1.733257866282789994, -0.9021709523542820186, 0.8299999999999999600 ) ) ; +#14413 = LINE ( 'NONE', #59475, #36987 ) ; +#14414 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14415 = LINE ( 'NONE', #51784, #96586 ) ; +#14416 = ORIENTED_EDGE ( 'NONE', *, *, #48966, .F. ) ; +#14417 = EDGE_CURVE ( 'NONE', #98695, #45824, #60885, .T. ) ; +#14418 = CYLINDRICAL_SURFACE ( 'NONE', #64529, 0.04999999999999991257 ) ; +#14419 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14420 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9291, 'distance_accuracy_value', 'NONE'); +#14421 = EDGE_CURVE ( 'NONE', #33372, #91985, #84828, .T. ) ; +#14422 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999919620, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#14423 = SURFACE_STYLE_USAGE ( .BOTH. , #69936 ) ; +#14424 = FACE_OUTER_BOUND ( 'NONE', #25047, .T. ) ; +#14425 = STYLED_ITEM ( 'NONE', ( #25916 ), #32397 ) ; +#14426 = STYLED_ITEM ( 'NONE', ( #42289 ), #75109 ) ; +#14427 = ORIENTED_EDGE ( 'NONE', *, *, #52888, .T. ) ; +#14428 = EDGE_CURVE ( 'NONE', #89309, #51969, #94496, .T. ) ; +#14429 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#14430 = VECTOR ( 'NONE', #6315, 1000.000000000000000 ) ; +#14431 = FACE_OUTER_BOUND ( 'NONE', #13055, .T. ) ; +#14432 = SURFACE_SIDE_STYLE ('',( #68078 ) ) ; +#14433 = SURFACE_SIDE_STYLE ('',( #60968 ) ) ; +#14434 = ORIENTED_EDGE ( 'NONE', *, *, #90885, .F. ) ; +#14435 = FILL_AREA_STYLE_COLOUR ( '', #86423 ) ; +#14436 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85370, 'distance_accuracy_value', 'NONE'); +#14437 = AXIS2_PLACEMENT_3D ( 'NONE', #52297, #61963, #7227 ) ; +#14438 = EDGE_CURVE ( 'NONE', #76382, #76548, #1083, .T. ) ; +#14439 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14440 = SURFACE_SIDE_STYLE ('',( #68593 ) ) ; +#14441 = VECTOR ( 'NONE', #88099, 999.9999999999998863 ) ; +#14442 = ORIENTED_EDGE ( 'NONE', *, *, #39419, .F. ) ; +#14443 = VECTOR ( 'NONE', #18354, 1000.000000000000000 ) ; +#14444 = EDGE_CURVE ( 'NONE', #48017, #1435, #24704, .T. ) ; +#14445 = FACE_OUTER_BOUND ( 'NONE', #96242, .T. ) ; +#14446 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14447 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83019 ) ) ; +#14448 = PRESENTATION_STYLE_ASSIGNMENT (( #23171 ) ) ; +#14449 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#14450 = ORIENTED_EDGE ( 'NONE', *, *, #83415, .F. ) ; +#14451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14452 = EDGE_CURVE ( 'NONE', #49623, #63125, #8149, .T. ) ; +#14453 = VECTOR ( 'NONE', #46191, 1000.000000000000114 ) ; +#14454 = VECTOR ( 'NONE', #48769, 1000.000000000000000 ) ; +#14455 = EDGE_CURVE ( 'NONE', #66007, #146, #47037, .T. ) ; +#14456 = AXIS2_PLACEMENT_3D ( 'NONE', #75321, #60043, #16524 ) ; +#14457 = ORIENTED_EDGE ( 'NONE', *, *, #8359, .T. ) ; +#14458 = ORIENTED_EDGE ( 'NONE', *, *, #33925, .F. ) ; +#14459 = STYLED_ITEM ( 'NONE', ( #68070 ), #42379 ) ; +#14460 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14461 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.4999999999999998890, -0.02000000000000000042 ) ) ; +#14462 = SURFACE_STYLE_FILL_AREA ( #45597 ) ; +#14463 = PLANE ( 'NONE', #100784 ) ; +#14464 = AXIS2_PLACEMENT_3D ( 'NONE', #32757, #1095, #40428 ) ; +#14465 = ORIENTED_EDGE ( 'NONE', *, *, #49518, .F. ) ; +#14466 = FACE_OUTER_BOUND ( 'NONE', #71755, .T. ) ; +#14467 = ORIENTED_EDGE ( 'NONE', *, *, #98164, .T. ) ; +#14468 = CARTESIAN_POINT ( 'NONE', ( -0.06036025838618214873, -1.154561795559095660, 0.8100000000000153744 ) ) ; +#14469 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14470 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14471 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14472 = VERTEX_POINT ( 'NONE', #38887 ) ; +#14473 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98024 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59930, #19581, #43553 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14475 = LINE ( 'NONE', #45612, #58431 ) ; +#14474 = CARTESIAN_POINT ( 'NONE', ( 1.790988317735369817, -1.106837409965790053, 0.8099999999999998312 ) ) ; +#14476 = ORIENTED_EDGE ( 'NONE', *, *, #23627, .F. ) ; +#14477 = AXIS2_PLACEMENT_3D ( 'NONE', #34465, #58468, #57444 ) ; +#14478 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8572, #39825, #85417, #56258 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14480 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14479 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14481 = SURFACE_SIDE_STYLE ('',( #99202 ) ) ; +#14482 = ADVANCED_FACE ( 'NONE', ( #32750 ), #32244, .T. ) ; +#14483 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14484 = VERTEX_POINT ( 'NONE', #40926 ) ; +#14485 = FILL_AREA_STYLE ('',( #22191 ) ) ; +#14486 = ORIENTED_EDGE ( 'NONE', *, *, #82156, .T. ) ; +#14487 = LINE ( 'NONE', #30847, #27532 ) ; +#14488 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14489 = SURFACE_STYLE_FILL_AREA ( #12448 ) ; +#14490 = EDGE_CURVE ( 'NONE', #58676, #54974, #55245, .T. ) ; +#14491 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46326, 'distance_accuracy_value', 'NONE'); +#14492 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14493 = VECTOR ( 'NONE', #16615, 1000.000000000000000 ) ; +#14495 = EDGE_CURVE ( 'NONE', #97114, #96104, #49086, .T. ) ; +#14494 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000444, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#14496 = SURFACE_SIDE_STYLE ('',( #82993 ) ) ; +#14497 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#14498 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19440 ) ) ; +#14499 = ORIENTED_EDGE ( 'NONE', *, *, #82484, .T. ) ; +#14500 = FACE_OUTER_BOUND ( 'NONE', #95979, .T. ) ; +#14501 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#14504 = FACE_OUTER_BOUND ( 'NONE', #75642, .T. ) ; +#14503 = DIRECTION ( 'NONE', ( 4.701977403289150032E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14502 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14505 = FACE_OUTER_BOUND ( 'NONE', #62107, .T. ) ; +#14506 = LINE ( 'NONE', #75333, #59924 ) ; +#14507 = SURFACE_STYLE_FILL_AREA ( #7808 ) ; +#14508 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58693 ), #39052 ) ; +#14509 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#14511 = ORIENTED_EDGE ( 'NONE', *, *, #74875, .T. ) ; +#14510 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89579 ) ) ; +#14512 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14513 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#14514 = FACE_OUTER_BOUND ( 'NONE', #56881, .T. ) ; +#14515 = SURFACE_SIDE_STYLE ('',( #62062 ) ) ; +#14516 = FACE_OUTER_BOUND ( 'NONE', #67591, .T. ) ; +#14517 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26225, 'distance_accuracy_value', 'NONE'); +#14518 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.19999999999999929, 0.000000000000000000 ) ) ; +#14519 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, -3.149999999999979927, 0.000000000000000000 ) ) ; +#14520 = CYLINDRICAL_SURFACE ( 'NONE', #73485, 0.04999999999999969746 ) ; +#14521 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#14522 = FILL_AREA_STYLE ('',( #21224 ) ) ; +#14524 = EDGE_CURVE ( 'NONE', #81638, #62618, #39895, .T. ) ; +#14523 = SURFACE_STYLE_USAGE ( .BOTH. , #69147 ) ; +#14525 = ADVANCED_FACE ( 'NONE', ( #70010 ), #17396, .F. ) ; +#14526 = CARTESIAN_POINT ( 'NONE', ( 3.924999999999999822, 0.5000000000000000000, -12.44500000000000028 ) ) ; +#14527 = FILL_AREA_STYLE_COLOUR ( '', #89642 ) ; +#14528 = AXIS2_PLACEMENT_3D ( 'NONE', #20868, #21870, #99860 ) ; +#14529 = SURFACE_STYLE_USAGE ( .BOTH. , #6350 ) ; +#14530 = STYLED_ITEM ( 'NONE', ( #78586 ), #1446 ) ; +#14531 = LINE ( 'NONE', #47232, #30102 ) ; +#14532 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75281, 'distance_accuracy_value', 'NONE'); +#14533 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#14534 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65705, 'distance_accuracy_value', 'NONE'); +#14535 = FILL_AREA_STYLE_COLOUR ( '', #44526 ) ; +#14536 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14537 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.500000000000000000, 3.738703894556490081E-79 ) ) ; +#14538 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14539 = STYLED_ITEM ( 'NONE', ( #99812 ), #779 ) ; +#14540 = DIRECTION ( 'NONE', ( 1.355252715606876105E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14541 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#14542 = ORIENTED_EDGE ( 'NONE', *, *, #39461, .F. ) ; +#14543 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14544 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#14545 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99244, 'distance_accuracy_value', 'NONE'); +#14546 = EDGE_CURVE ( 'NONE', #98998, #71570, #43408, .T. ) ; +#14547 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#14548 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#14549 = EDGE_LOOP ( 'NONE', ( #73040, #79745, #65526, #15869 ) ) ; +#14550 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8099999999999013545 ) ) ; +#14551 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#14552 = SURFACE_STYLE_USAGE ( .BOTH. , #47252 ) ; +#14553 = SURFACE_STYLE_FILL_AREA ( #74887 ) ; +#14554 = ORIENTED_EDGE ( 'NONE', *, *, #23390, .T. ) ; +#14555 = FACE_OUTER_BOUND ( 'NONE', #62088, .T. ) ; +#14556 = AXIS2_PLACEMENT_3D ( 'NONE', #36106, #59613, #51426 ) ; +#14557 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14558 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16519, 'distance_accuracy_value', 'NONE'); +#14559 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.05000000000000000971, 0.1900000000000000022 ) ) ; +#14560 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14561 = VERTEX_POINT ( 'NONE', #2610 ) ; +#14562 = ORIENTED_EDGE ( 'NONE', *, *, #12039, .F. ) ; +#14563 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14564 = CARTESIAN_POINT ( 'NONE', ( 5.413238000000000660, 8.675382000000000815, 0.8648700000000000276 ) ) ; +#14565 = VECTOR ( 'NONE', #58475, 1000.000000000000000 ) ; +#14566 = VERTEX_POINT ( 'NONE', #35291 ) ; +#14567 = LINE ( 'NONE', #5897, #49385 ) ; +#14568 = FACE_OUTER_BOUND ( 'NONE', #92337, .T. ) ; +#14569 = CARTESIAN_POINT ( 'NONE', ( 0.5390356320350060404, -1.127406710959419911, 0.8100000000000000533 ) ) ; +#14570 = FILL_AREA_STYLE ('',( #30405 ) ) ; +#14571 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14572 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #72563, #58800 ), + ( #2633, #49614 ), + ( #34310, #4618 ), + ( #65399, #42454 ), + ( #73583, #89895 ), + ( #34806, #27139 ), + ( #19457, #50630 ), + ( #19955, #59310 ), + ( #76080, #6069 ), + ( #90913, #29131 ), + ( #20960, #5591 ), + ( #85244, #13734 ), + ( #68406, #28616 ), + ( #60300, #60790 ), + ( #99471, #99948 ), + ( #36789, #5100 ), + ( #92861, #61796 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06966389745086019880, 0.1364315478428499984, 0.2011873724129789875, 0.2645983123399139880, 0.3259037851543959974, 0.3855761511408299924, 0.4444834551525069788, 0.5032708546699640184, 0.5621995445251509738, 0.6211282343803400385, 0.6821163697534170511, 0.7443520026810319656, 0.8704105427126580530, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14573 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47259 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50968, #58644, #51478 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14574 = AXIS2_PLACEMENT_3D ( 'NONE', #54081, #89987, #35409 ) ; +#14575 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #89335, #51809 ) ; +#14576 = FILL_AREA_STYLE_COLOUR ( '', #34675 ) ; +#14577 = VERTEX_POINT ( 'NONE', #90369 ) ; +#14578 = EDGE_CURVE ( 'NONE', #71500, #82294, #30520, .T. ) ; +#14579 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14580 = ORIENTED_EDGE ( 'NONE', *, *, #60959, .F. ) ; +#14581 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14582 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14583 = VECTOR ( 'NONE', #47108, 1000.000000000000000 ) ; +#14584 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#14585 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14586 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73330 ) ) ; +#14587 = AXIS2_PLACEMENT_3D ( 'NONE', #32464, #33482, #87088 ) ; +#14588 = SURFACE_STYLE_FILL_AREA ( #37132 ) ; +#14589 = CARTESIAN_POINT ( 'NONE', ( 6.650674750249975453, 1.696237750249973919, 0.8991599999999999593 ) ) ; +#14590 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#14591 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14592 = ORIENTED_EDGE ( 'NONE', *, *, #81853, .F. ) ; +#14593 = VERTEX_POINT ( 'NONE', #58275 ) ; +#14594 = EDGE_LOOP ( 'NONE', ( #20582, #30955, #46889, #52345 ) ) ; +#14595 = CARTESIAN_POINT ( 'NONE', ( 1.338535375846370057, -1.276477384597439979, 0.8299999999999999600 ) ) ; +#14596 = SURFACE_STYLE_USAGE ( .BOTH. , #13060 ) ; +#14597 = STYLED_ITEM ( 'NONE', ( #79350 ), #64027 ) ; +#14598 = EDGE_CURVE ( 'NONE', #84594, #5636, #73057, .T. ) ; +#14599 = STYLED_ITEM ( 'NONE', ( #46292 ), #1570 ) ; +#14600 = ORIENTED_EDGE ( 'NONE', *, *, #20541, .F. ) ; +#14601 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22824 ), #99327 ) ; +#14602 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1629 ) ) ; +#14603 = FILL_AREA_STYLE ('',( #28966 ) ) ; +#14604 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#14605 = ORIENTED_EDGE ( 'NONE', *, *, #59275, .F. ) ; +#14607 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14606 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14608 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14609 = EDGE_LOOP ( 'NONE', ( #35350, #9112, #22529, #30422, #62853 ) ) ; +#14610 = ORIENTED_EDGE ( 'NONE', *, *, #28237, .F. ) ; +#14611 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14612 = CARTESIAN_POINT ( 'NONE', ( 0.9629666814316270029, -1.351356007592229957, 0.8100000000000000533 ) ) ; +#14613 = FACE_OUTER_BOUND ( 'NONE', #39043, .T. ) ; +#14614 = EDGE_CURVE ( 'NONE', #15064, #37511, #12182, .T. ) ; +#14615 = LINE ( 'NONE', #98345, #18918 ) ; +#14616 = CARTESIAN_POINT ( 'NONE', ( -1.020615739564168400, -0.9895216834026616670, 0.8099999999999957234 ) ) ; +#14617 = VECTOR ( 'NONE', #58251, 1000.000000000000114 ) ; +#14618 = VECTOR ( 'NONE', #51021, 1000.000000000000000 ) ; +#14619 = FILL_AREA_STYLE ('',( #84612 ) ) ; +#14620 = CARTESIAN_POINT ( 'NONE', ( -0.007915629041866760474, -1.066767002799750008, 0.8100000000000000533 ) ) ; +#14621 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -1.899999999999999911, -0.02000000000004609896 ) ) ; +#14622 = FILL_AREA_STYLE ('',( #84614 ) ) ; +#14623 = ORIENTED_EDGE ( 'NONE', *, *, #15463, .F. ) ; +#14624 = ORIENTED_EDGE ( 'NONE', *, *, #85564, .F. ) ; +#14625 = ADVANCED_FACE ( 'NONE', ( #34781 ), #77396, .F. ) ; +#14626 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14627 = CARTESIAN_POINT ( 'NONE', ( -1.009874566215796854, -1.487199427423350429, 0.8099999999996295719 ) ) ; +#14628 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, 0.000000000000000000 ) ) ; +#14629 = SURFACE_STYLE_USAGE ( .BOTH. , #98846 ) ; +#14630 = CARTESIAN_POINT ( 'NONE', ( 0.1238200612200860418, -3.099999999999980105, 0.000000000000000000 ) ) ; +#14631 = SURFACE_STYLE_USAGE ( .BOTH. , #39161 ) ; +#14632 = EDGE_CURVE ( 'NONE', #71740, #88552, #60762, .T. ) ; +#14633 = SURFACE_SIDE_STYLE ('',( #91761 ) ) ; +#14634 = ORIENTED_EDGE ( 'NONE', *, *, #76030, .T. ) ; +#14635 = FACE_OUTER_BOUND ( 'NONE', #64060, .T. ) ; +#14636 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, 3.500000000000000444, 0.000000000000000000 ) ) ; +#14637 = AXIS2_PLACEMENT_3D ( 'NONE', #36337, #98515, #97572 ) ; +#14638 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 1.696237999999999913, 0.8648700000000000276 ) ) ; +#14639 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#14640 = CARTESIAN_POINT ( 'NONE', ( 1.859836464378280096, -1.220010286732279958, 0.8100000000000000533 ) ) ; +#14642 = EDGE_CURVE ( 'NONE', #3602, #88109, #99925, .T. ) ; +#14641 = SURFACE_STYLE_FILL_AREA ( #70314 ) ; +#14644 = EDGE_CURVE ( 'NONE', #18155, #82206, #30076, .T. ) ; +#14643 = LINE ( 'NONE', #45795, #92088 ) ; +#14645 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55545 ) ) ; +#14646 = SURFACE_STYLE_FILL_AREA ( #91781 ) ; +#14647 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14648 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4600000000000000200, 0.2250000000000000333 ) ) ; +#14649 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#14650 = DIRECTION ( 'NONE', ( 0.000000000000000000, 3.357926749866047180E-13, 1.000000000000000000 ) ) ; +#14651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66878 ) ) ; +#14652 = EDGE_CURVE ( 'NONE', #17177, #15107, #36763, .T. ) ; +#14653 = EDGE_CURVE ( 'NONE', #44005, #43289, #76055, .T. ) ; +#14654 = CARTESIAN_POINT ( 'NONE', ( 1.322240070112479904, -1.010360997253880067, 0.8299999999999995159 ) ) ; +#14655 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40996, 'distance_accuracy_value', 'NONE'); +#14656 = PRESENTATION_STYLE_ASSIGNMENT (( #68795 ) ) ; +#14657 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, 0.000000000000000000 ) ) ; +#14658 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14659 = ORIENTED_EDGE ( 'NONE', *, *, #77053, .F. ) ; +#14660 = FILL_AREA_STYLE_COLOUR ( '', #38063 ) ; +#14661 = CIRCLE ( 'NONE', #75082, 0.09999999999999939493 ) ; +#14662 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14663 = EDGE_CURVE ( 'NONE', #38757, #86575, #13704, .T. ) ; +#14664 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14665 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42660, 'distance_accuracy_value', 'NONE'); +#14666 = AXIS2_PLACEMENT_3D ( 'NONE', #11597, #66321, #37200 ) ; +#14667 = STYLED_ITEM ( 'NONE', ( #19726 ), #65374 ) ; +#14668 = FACE_OUTER_BOUND ( 'NONE', #54835, .T. ) ; +#14669 = CARTESIAN_POINT ( 'NONE', ( 1.063910042292729008, -1.022720379215139808, 0.8099999999999757394 ) ) ; +#14670 = EDGE_CURVE ( 'NONE', #100419, #97394, #28586, .T. ) ; +#14671 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74741 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36676, #29495, #75954 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14672 = VERTEX_POINT ( 'NONE', #69361 ) ; +#14673 = STYLED_ITEM ( 'NONE', ( #61560 ), #1756 ) ; +#14674 = FILL_AREA_STYLE_COLOUR ( '', #61853 ) ; +#14675 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11227 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32610, #80587, #10509 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14676 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14677 = PRESENTATION_STYLE_ASSIGNMENT (( #84660 ) ) ; +#14678 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14679 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47901, 'distance_accuracy_value', 'NONE'); +#14680 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100612, 'distance_accuracy_value', 'NONE'); +#14681 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14682 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14683 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#14684 = ORIENTED_EDGE ( 'NONE', *, *, #33577, .F. ) ; +#14685 = ORIENTED_EDGE ( 'NONE', *, *, #18769, .T. ) ; +#14686 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14687 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14688 = ORIENTED_EDGE ( 'NONE', *, *, #22695, .T. ) ; +#14690 = SURFACE_STYLE_FILL_AREA ( #30516 ) ; +#14689 = STYLED_ITEM ( 'NONE', ( #11472 ), #51479 ) ; +#14691 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#14692 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14693 = SURFACE_STYLE_USAGE ( .BOTH. , #45833 ) ; +#14694 = SURFACE_STYLE_USAGE ( .BOTH. , #62736 ) ; +#14695 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #6351 ) ; +#14696 = DIRECTION ( 'NONE', ( 0.7071075504167448900, 0.7071060119555133694, 0.000000000000000000 ) ) ; +#14697 = FILL_AREA_STYLE_COLOUR ( '', #16341 ) ; +#14699 = ORIENTED_EDGE ( 'NONE', *, *, #45216, .T. ) ; +#14698 = ORIENTED_EDGE ( 'NONE', *, *, #48726, .F. ) ; +#14700 = ADVANCED_FACE ( 'NONE', ( #84715 ), #90882, .T. ) ; +#14701 = ORIENTED_EDGE ( 'NONE', *, *, #87737, .F. ) ; +#14702 = PRESENTATION_STYLE_ASSIGNMENT (( #47400 ) ) ; +#14704 = LINE ( 'NONE', #77033, #13673 ) ; +#14703 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, 0.000000000000000000 ) ) ; +#14705 = ORIENTED_EDGE ( 'NONE', *, *, #64984, .T. ) ; +#14706 = EDGE_CURVE ( 'NONE', #5293, #79328, #7523, .T. ) ; +#14707 = ORIENTED_EDGE ( 'NONE', *, *, #58428, .T. ) ; +#14708 = MANIFOLD_SOLID_BREP ( 'ÊäÈë5', #27364 ) ; +#14709 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.123820061220085265, 0.000000000000000000 ) ) ; +#14710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14711 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11461 ), #8178 ) ; +#14712 = STYLED_ITEM ( 'NONE', ( #31429 ), #33513 ) ; +#14713 = LINE ( 'NONE', #83716, #75976 ) ; +#14714 = CARTESIAN_POINT ( 'NONE', ( -0.5276249439448480461, -0.9003793229264169806, 0.8299999999999999600 ) ) ; +#14715 = ORIENTED_EDGE ( 'NONE', *, *, #52242, .F. ) ; +#14716 = PLANE ( 'NONE', #22640 ) ; +#14717 = ORIENTED_EDGE ( 'NONE', *, *, #9312, .T. ) ; +#14718 = ORIENTED_EDGE ( 'NONE', *, *, #3865, .F. ) ; +#14719 = SURFACE_SIDE_STYLE ('',( #84708 ) ) ; +#14720 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22943 ), #86561 ) ; +#14721 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#14722 = FILL_AREA_STYLE ('',( #69350 ) ) ; +#14723 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66280, #81622, #35160 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14725 = ORIENTED_EDGE ( 'NONE', *, *, #13238, .F. ) ; +#14724 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64636, 'distance_accuracy_value', 'NONE'); +#14726 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14727 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.1000000000000000056, -11.91999999999999993 ) ) ; +#14728 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14729 = ORIENTED_EDGE ( 'NONE', *, *, #67934, .T. ) ; +#14730 = AXIS2_PLACEMENT_3D ( 'NONE', #84683, #53557, #100868 ) ; +#14731 = CARTESIAN_POINT ( 'NONE', ( -0.004761740495047140850, -1.264112177694660000, 0.8299999999999999600 ) ) ; +#14732 = VERTEX_POINT ( 'NONE', #86740 ) ; +#14733 = EDGE_LOOP ( 'NONE', ( #36403, #47906, #51480, #64779 ) ) ; +#14735 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8648700000000000276 ) ) ; +#14734 = SURFACE_STYLE_USAGE ( .BOTH. , #21070 ) ; +#14736 = EDGE_CURVE ( 'NONE', #7257, #65355, #100545, .T. ) ; +#14737 = STYLED_ITEM ( 'NONE', ( #75910 ), #6879 ) ; +#14738 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#14739 = FILL_AREA_STYLE ('',( #92372 ) ) ; +#14740 = STYLED_ITEM ( 'NONE', ( #27282 ), #65770 ) ; +#14741 = PRESENTATION_STYLE_ASSIGNMENT (( #15762 ) ) ; +#14742 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14743 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14744 = ORIENTED_EDGE ( 'NONE', *, *, #43151, .F. ) ; +#14745 = CARTESIAN_POINT ( 'NONE', ( 0.4381267573579120111, -1.159910275666830026, 0.8299999999999999600 ) ) ; +#14746 = AXIS2_PLACEMENT_3D ( 'NONE', #51253, #49762, #26775 ) ; +#14747 = CARTESIAN_POINT ( 'NONE', ( 0.09346250786341020467, -1.325441991778449902, 0.8100000000000000533 ) ) ; +#14748 = VERTEX_POINT ( 'NONE', #77561 ) ; +#14749 = SURFACE_STYLE_FILL_AREA ( #51627 ) ; +#14751 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43756, 'distance_accuracy_value', 'NONE'); +#14750 = SURFACE_SIDE_STYLE ('',( #31126 ) ) ; +#14752 = PLANE ( 'NONE', #91980 ) ; +#14753 = FILL_AREA_STYLE ('',( #37304 ) ) ; +#14754 = CARTESIAN_POINT ( 'NONE', ( 1.698015391961940068, -0.9623926821384259922, 0.8100000000000000533 ) ) ; +#14755 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14756 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14757 = SURFACE_STYLE_FILL_AREA ( #30589 ) ; +#14758 = FILL_AREA_STYLE ('',( #85742 ) ) ; +#14759 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#14760 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14761 = SURFACE_STYLE_USAGE ( .BOTH. , #53125 ) ; +#14762 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68578 ), #13126 ) ; +#14763 = PRESENTATION_STYLE_ASSIGNMENT (( #78107 ) ) ; +#14764 = LINE ( 'NONE', #4750, #52889 ) ; +#14765 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14766 = LINE ( 'NONE', #84264, #52153 ) ; +#14767 = PRESENTATION_STYLE_ASSIGNMENT (( #29144 ) ) ; +#14768 = EDGE_CURVE ( 'NONE', #60846, #64967, #77099, .T. ) ; +#14769 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74658, 'distance_accuracy_value', 'NONE'); +#14770 = VERTEX_POINT ( 'NONE', #39775 ) ; +#14771 = LINE ( 'NONE', #93395, #24861 ) ; +#14772 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14773 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14774 = SURFACE_STYLE_FILL_AREA ( #30123 ) ; +#14775 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#14776 = STYLED_ITEM ( 'NONE', ( #51737 ), #18283 ) ; +#14777 = LINE ( 'NONE', #94429, #20502 ) ; +#14778 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80949, #49282, #17599 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14779 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.5000000000000000000, -13.54999999999999893 ) ) ; +#14780 = FACE_OUTER_BOUND ( 'NONE', #90095, .T. ) ; +#14781 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_L0201_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_L0201_20210301.STEP', '', ( #49416 ) ) ; +#14782 = ADVANCED_FACE ( 'NONE', ( #100902 ), #79600, .T. ) ; +#14783 = STYLED_ITEM ( 'NONE', ( #57949 ), #95551 ) ; +#14784 = ORIENTED_EDGE ( 'NONE', *, *, #7514, .T. ) ; +#14785 = SURFACE_STYLE_FILL_AREA ( #61828 ) ; +#14786 = ORIENTED_EDGE ( 'NONE', *, *, #84937, .F. ) ; +#14787 = FILL_AREA_STYLE ('',( #84770 ) ) ; +#14788 = AXIS2_PLACEMENT_3D ( 'NONE', #19687, #81511, #51352 ) ; +#14789 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#14790 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#14791 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14792 = AXIS2_PLACEMENT_3D ( 'NONE', #99217, #59559, #13456 ) ; +#14793 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14794 = FILL_AREA_STYLE_COLOUR ( '', #84787 ) ; +#14795 = FILL_AREA_STYLE ('',( #77126 ) ) ; +#14796 = ORIENTED_EDGE ( 'NONE', *, *, #55519, .F. ) ; +#14797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39325 ) ) ; +#14798 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14799 = VERTEX_POINT ( 'NONE', #9550 ) ; +#14800 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49548, #81700, #87826, #2569 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14801 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14802 = AXIS2_PLACEMENT_3D ( 'NONE', #26157, #56311, #16937 ) ; +#14803 = VERTEX_POINT ( 'NONE', #23449 ) ; +#14804 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14805 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14806 = EDGE_CURVE ( 'NONE', #62472, #97238, #70391, .T. ) ; +#14807 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19758 ) ) ; +#14808 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14809 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#14810 = SURFACE_STYLE_USAGE ( .BOTH. , #53672 ) ; +#14812 = EDGE_LOOP ( 'NONE', ( #95699, #92226, #47386, #87972 ) ) ; +#14811 = ORIENTED_EDGE ( 'NONE', *, *, #56054, .T. ) ; +#14813 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998557, 0.1400000000000000133 ) ) ; +#14814 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14815 = EDGE_LOOP ( 'NONE', ( #23518, #86683, #22970, #1597 ) ) ; +#14816 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#14818 = CARTESIAN_POINT ( 'NONE', ( -0.4458447660039659977, -1.054313421655699967, 0.8299999999999999600 ) ) ; +#14817 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#14819 = EDGE_LOOP ( 'NONE', ( #54959, #34957, #61103, #32011 ) ) ; +#14820 = ADVANCED_FACE ( 'NONE', ( #79092 ), #9048, .T. ) ; +#14821 = ORIENTED_EDGE ( 'NONE', *, *, #93686, .T. ) ; +#14822 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14823 = PRESENTATION_STYLE_ASSIGNMENT (( #31205 ) ) ; +#14824 = SURFACE_STYLE_USAGE ( .BOTH. , #76656 ) ; +#14825 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.36999999999999922 ) ) ; +#14826 = VECTOR ( 'NONE', #64686, 1000.000000000000114 ) ; +#14828 = FILL_AREA_STYLE_COLOUR ( '', #79429 ) ; +#14827 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14829 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14830 = ORIENTED_EDGE ( 'NONE', *, *, #59425, .T. ) ; +#14831 = ORIENTED_EDGE ( 'NONE', *, *, #70837, .T. ) ; +#14832 = VERTEX_POINT ( 'NONE', #64764 ) ; +#14833 = AXIS2_PLACEMENT_3D ( 'NONE', #24068, #92934, #38863 ) ; +#14834 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14835 = VECTOR ( 'NONE', #87581, 1000.000000000000227 ) ; +#14836 = ORIENTED_EDGE ( 'NONE', *, *, #77302, .T. ) ; +#14837 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95173, #16565, #31407, #54412 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14838 = PLANE ( 'NONE', #24673 ) ; +#14839 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14840 = FILL_AREA_STYLE_COLOUR ( '', #78194 ) ; +#14841 = ORIENTED_EDGE ( 'NONE', *, *, #28732, .T. ) ; +#14842 = SURFACE_STYLE_USAGE ( .BOTH. , #52225 ) ; +#14843 = EDGE_LOOP ( 'NONE', ( #100171, #60687, #11110, #54065 ) ) ; +#14844 = ADVANCED_FACE ( 'NONE', ( #35666 ), #87747, .F. ) ; +#14845 = CARTESIAN_POINT ( 'NONE', ( 0.06967798674591889341, -1.043958301690999901, 0.8299999999999988498 ) ) ; +#14846 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#14847 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26370 ) ) ; +#14848 = VECTOR ( 'NONE', #99527, 1000.000000000000000 ) ; +#14849 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2801, #66577, #18598, #42609 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#14850 = EDGE_CURVE ( 'NONE', #66638, #17384, #34159, .T. ) ; +#14852 = ORIENTED_EDGE ( 'NONE', *, *, #8516, .T. ) ; +#14851 = PRESENTATION_STYLE_ASSIGNMENT (( #30701 ) ) ; +#14853 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80167 ), #70350 ) ; +#14854 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14855 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14856 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81852 ) ) ; +#14858 = SURFACE_STYLE_USAGE ( .BOTH. , #76684 ) ; +#14857 = FILL_AREA_STYLE_COLOUR ( '', #25237 ) ; +#14859 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14860 = CARTESIAN_POINT ( 'NONE', ( 1.769821822789199972, -1.235192314287260062, 0.8099999999999996092 ) ) ; +#14861 = VERTEX_POINT ( 'NONE', #96379 ) ; +#14862 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71995 ) ) ; +#14863 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#14864 = AXIS2_PLACEMENT_3D ( 'NONE', #92611, #51364, #44169 ) ; +#14865 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.53504399999999919, 0.8648700000000000276 ) ) ; +#14866 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14867 = SURFACE_SIDE_STYLE ('',( #13325 ) ) ; +#14868 = PRESENTATION_STYLE_ASSIGNMENT (( #62924 ) ) ; +#14869 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14870 = ADVANCED_FACE ( 'NONE', ( #89747 ), #49981, .T. ) ; +#14871 = LINE ( 'NONE', #23100, #54827 ) ; +#14872 = MANIFOLD_SOLID_BREP ( 'ÊäÈë127', #32245 ) ; +#14873 = ADVANCED_FACE ( 'NONE', ( #83614 ), #13069, .T. ) ; +#14874 = AXIS2_PLACEMENT_3D ( 'NONE', #55449, #30383, #70728 ) ; +#14875 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34502 ), #42705 ) ; +#14876 = SURFACE_SIDE_STYLE ('',( #94 ) ) ; +#14877 = ORIENTED_EDGE ( 'NONE', *, *, #62047, .F. ) ; +#14878 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.000000000000000000 ) ) ; +#14879 = FACE_OUTER_BOUND ( 'NONE', #25977, .T. ) ; +#14880 = ORIENTED_EDGE ( 'NONE', *, *, #20669, .T. ) ; +#14881 = LINE ( 'NONE', #85374, #29182 ) ; +#14882 = AXIS2_PLACEMENT_3D ( 'NONE', #13532, #44723, #90717 ) ; +#14884 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -9.880000000000000782, 0.2500000000000000000 ) ) ; +#14883 = LINE ( 'NONE', #46027, #93092 ) ; +#14885 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8648700000000000276 ) ) ; +#14886 = AXIS2_PLACEMENT_3D ( 'NONE', #26850, #97244, #11914 ) ; +#14887 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#14888 = ADVANCED_FACE ( 'NONE', ( #67264 ), #52983, .F. ) ; +#14889 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14890 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1911 ) ) ; +#14891 = ORIENTED_EDGE ( 'NONE', *, *, #42961, .F. ) ; +#14892 = FILL_AREA_STYLE_COLOUR ( '', #11904 ) ; +#14893 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14894 = PLANE ( 'NONE', #83322 ) ; +#14895 = SURFACE_STYLE_USAGE ( .BOTH. , #53744 ) ; +#14896 = SURFACE_STYLE_FILL_AREA ( #68039 ) ; +#14897 = LINE ( 'NONE', #30745, #29076 ) ; +#14898 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#14899 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14900 = VECTOR ( 'NONE', #7829, 1000.000000000000000 ) ; +#14901 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14902 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#14903 = LINE ( 'NONE', #46043, #94201 ) ; +#14904 = FILL_AREA_STYLE_COLOUR ( '', #18661 ) ; +#14905 = FILL_AREA_STYLE_COLOUR ( '', #21571 ) ; +#14906 = EDGE_CURVE ( 'NONE', #92602, #62618, #54995, .T. ) ; +#14907 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14908 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#14909 = ORIENTED_EDGE ( 'NONE', *, *, #48394, .F. ) ; +#14910 = VERTEX_POINT ( 'NONE', #23844 ) ; +#14911 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#14912 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14913 = PRESENTATION_STYLE_ASSIGNMENT (( #23140 ) ) ; +#14914 = CARTESIAN_POINT ( 'NONE', ( -1.084303872719659889, -1.510436674894549913, 0.8299999999999981837 ) ) ; +#14915 = SURFACE_STYLE_FILL_AREA ( #77236 ) ; +#14916 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#14917 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#14918 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14919 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#14920 = ORIENTED_EDGE ( 'NONE', *, *, #44365, .F. ) ; +#14921 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#14922 = FILL_AREA_STYLE ('',( #77245 ) ) ; +#14923 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5374 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94463, #95966, #26071 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14924 = ADVANCED_FACE ( 'NONE', ( #46261 ), #86102, .T. ) ; +#14925 = ORIENTED_EDGE ( 'NONE', *, *, #80899, .T. ) ; +#14926 = FILL_AREA_STYLE ('',( #23154 ) ) ; +#14927 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#14928 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60699 ), #28053 ) ; +#14929 = PRESENTATION_STYLE_ASSIGNMENT (( #93546 ) ) ; +#14930 = PLANE ( 'NONE', #93504 ) ; +#14931 = FACE_OUTER_BOUND ( 'NONE', #29705, .T. ) ; +#14932 = ADVANCED_FACE ( 'NONE', ( #69762 ), #16728, .T. ) ; +#14933 = PRESENTATION_STYLE_ASSIGNMENT (( #61476 ) ) ; +#14934 = SURFACE_SIDE_STYLE ('',( #39469 ) ) ; +#14935 = ORIENTED_EDGE ( 'NONE', *, *, #12480, .F. ) ; +#14936 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#14937 = VECTOR ( 'NONE', #97027, 1000.000000000000000 ) ; +#14938 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14939 = EDGE_CURVE ( 'NONE', #81837, #19927, #68591, .T. ) ; +#14940 = AXIS2_PLACEMENT_3D ( 'NONE', #36774, #67877, #99460 ) ; +#14941 = VERTEX_POINT ( 'NONE', #86917 ) ; +#14942 = FILL_AREA_STYLE ('',( #47653 ) ) ; +#14943 = PLANE ( 'NONE', #88120 ) ; +#14944 = LINE ( 'NONE', #77268, #99236 ) ; +#14945 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29758 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81178, #3556, #50544 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14946 = FILL_AREA_STYLE ('',( #92568 ) ) ; +#14947 = SURFACE_SIDE_STYLE ('',( #5286 ) ) ; +#14948 = ORIENTED_EDGE ( 'NONE', *, *, #46234, .F. ) ; +#14949 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#14950 = VERTEX_POINT ( 'NONE', #46570 ) ; +#14951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93609, 'distance_accuracy_value', 'NONE'); +#14952 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1135 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25242, #74183, #64007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14953 = VERTEX_POINT ( 'NONE', #62947 ) ; +#14955 = EDGE_LOOP ( 'NONE', ( #43996, #30166, #2737, #52666 ) ) ; +#14954 = SURFACE_SIDE_STYLE ('',( #63012 ) ) ; +#14956 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#14958 = SURFACE_STYLE_FILL_AREA ( #45596 ) ; +#14957 = PLANE ( 'NONE', #3693 ) ; +#14959 = PLANE ( 'NONE', #59484 ) ; +#14960 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53151 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52784, #90578, #59975 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#14961 = ORIENTED_EDGE ( 'NONE', *, *, #65152, .T. ) ; +#14962 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#14963 = ORIENTED_EDGE ( 'NONE', *, *, #51816, .F. ) ; +#14964 = SURFACE_SIDE_STYLE ('',( #21168 ) ) ; +#14965 = FILL_AREA_STYLE ('',( #37516 ) ) ; +#14966 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14967 = VERTEX_POINT ( 'NONE', #37925 ) ; +#14968 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935067599, 0.8100000000000000533 ) ) ; +#14969 = ORIENTED_EDGE ( 'NONE', *, *, #58971, .T. ) ; +#14971 = EDGE_CURVE ( 'NONE', #75802, #36985, #38434, .T. ) ; +#14970 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#14972 = ADVANCED_FACE ( 'NONE', ( #85384 ), #618, .T. ) ; +#14973 = SURFACE_SIDE_STYLE ('',( #78333 ) ) ; +#14974 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#14975 = AXIS2_PLACEMENT_3D ( 'NONE', #17240, #25448, #64728 ) ; +#14976 = ORIENTED_EDGE ( 'NONE', *, *, #80558, .T. ) ; +#14977 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14978 = ORIENTED_EDGE ( 'NONE', *, *, #43049, .T. ) ; +#14980 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14979 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#14981 = ADVANCED_FACE ( 'NONE', ( #82164 ), #11098, .T. ) ; +#14982 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#14983 = EDGE_CURVE ( 'NONE', #81364, #46126, #27036, .T. ) ; +#14984 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13358 ) ) ; +#14985 = AXIS2_PLACEMENT_3D ( 'NONE', #30286, #23675, #24715 ) ; +#14986 = FILL_AREA_STYLE ('',( #92131 ) ) ; +#14988 = EDGE_CURVE ( 'NONE', #12804, #3215, #72979, .T. ) ; +#14987 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#14989 = FACE_OUTER_BOUND ( 'NONE', #95585, .T. ) ; +#14990 = CYLINDRICAL_SURFACE ( 'NONE', #60635, 0.05000000000000012768 ) ; +#14991 = VECTOR ( 'NONE', #98641, 1000.000000000000114 ) ; +#14992 = PRESENTATION_STYLE_ASSIGNMENT (( #68648 ) ) ; +#14993 = ORIENTED_EDGE ( 'NONE', *, *, #93932, .F. ) ; +#14994 = CARTESIAN_POINT ( 'NONE', ( -1.246499984327120059, -1.124851061273939967, 0.8300000000000002931 ) ) ; +#14995 = FILL_AREA_STYLE_COLOUR ( '', #28373 ) ; +#14997 = VECTOR ( 'NONE', #69609, 1000.000000000000000 ) ; +#14996 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#14998 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9331, 'distance_accuracy_value', 'NONE'); +#14999 = VECTOR ( 'NONE', #63323, 1000.000000000000000 ) ; +#15000 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#15001 = ADVANCED_FACE ( 'NONE', ( #34704 ), #27538, .T. ) ; +#15002 = STYLED_ITEM ( 'NONE', ( #4822 ), #11102 ) ; +#15003 = FILL_AREA_STYLE_COLOUR ( '', #94065 ) ; +#15004 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.004999999999999999237, -0.2500000000000000000 ) ) ; +#15005 = ORIENTED_EDGE ( 'NONE', *, *, #84272, .F. ) ; +#15006 = VECTOR ( 'NONE', #56133, 1000.000000000000000 ) ; +#15007 = SURFACE_STYLE_FILL_AREA ( #68659 ) ; +#15009 = EDGE_CURVE ( 'NONE', #97211, #53046, #78387, .T. ) ; +#15008 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#15010 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15011 = FILL_AREA_STYLE ('',( #98743 ) ) ; +#15012 = CARTESIAN_POINT ( 'NONE', ( -0.02315300183346909874, -1.415447185383410078, 0.8299999999999999600 ) ) ; +#15013 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15014 = FILL_AREA_STYLE_COLOUR ( '', #95305 ) ; +#15015 = AXIS2_PLACEMENT_3D ( 'NONE', #74379, #34092, #18201 ) ; +#15016 = SURFACE_SIDE_STYLE ('',( #16548 ) ) ; +#15017 = DIRECTION ( 'NONE', ( 2.567390744445670062E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15018 = SURFACE_SIDE_STYLE ('',( #69144 ) ) ; +#15019 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15020 = ADVANCED_FACE ( 'NONE', ( #46311 ), #21859, .T. ) ; +#15021 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000005745, 0.3800000000146489532, 0.6999285677985319643 ) ) ; +#15022 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44423 ) ) ; +#15023 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15024 = LINE ( 'NONE', #46182, #17818 ) ; +#15025 = EDGE_CURVE ( 'NONE', #21132, #77646, #77935, .T. ) ; +#15026 = LINE ( 'NONE', #92645, #30657 ) ; +#15027 = LINE ( 'NONE', #62583, #93622 ) ; +#15028 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15029 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#15030 = EDGE_CURVE ( 'NONE', #73506, #73427, #52022, .T. ) ; +#15031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15032 = LINE ( 'NONE', #29406, #94362 ) ; +#15033 = SURFACE_STYLE_FILL_AREA ( #30372 ) ; +#15034 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#15035 = FILL_AREA_STYLE ('',( #85024 ) ) ; +#15036 = EDGE_LOOP ( 'NONE', ( #792, #82323, #76565, #11326 ) ) ; +#15037 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15038 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#15039 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65603 ), #28156 ) ; +#15040 = AXIS2_PLACEMENT_3D ( 'NONE', #29530, #22361, #14664 ) ; +#15041 = ORIENTED_EDGE ( 'NONE', *, *, #17765, .F. ) ; +#15042 = SURFACE_STYLE_USAGE ( .BOTH. , #63609 ) ; +#15043 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28161 ), #72178 ) ; +#15044 = LINE ( 'NONE', #7855, #67319 ) ; +#15045 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15046 = ADVANCED_FACE ( 'NONE', ( #68306 ), #92295, .T. ) ; +#15047 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15048 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#15049 = ORIENTED_EDGE ( 'NONE', *, *, #27679, .F. ) ; +#15050 = PRESENTATION_STYLE_ASSIGNMENT (( #85044 ) ) ; +#15051 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#15052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63030, 'distance_accuracy_value', 'NONE'); +#15053 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.123820061220085265, 0.000000000000000000 ) ) ; +#15054 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58166 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64178, #56542, #18168 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15055 = VECTOR ( 'NONE', #95034, 1000.000000000000000 ) ; +#15056 = FILL_AREA_STYLE ('',( #38106 ) ) ; +#15057 = EDGE_CURVE ( 'NONE', #94045, #25581, #71343, .T. ) ; +#15058 = ORIENTED_EDGE ( 'NONE', *, *, #49345, .F. ) ; +#15059 = ORIENTED_EDGE ( 'NONE', *, *, #54604, .F. ) ; +#15060 = VECTOR ( 'NONE', #49413, 1000.000000000000114 ) ; +#15061 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79244, #31763, #87397 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15062 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#15063 = FILL_AREA_STYLE ('',( #63114 ) ) ; +#15064 = VERTEX_POINT ( 'NONE', #8456 ) ; +#15065 = LINE ( 'NONE', #46217, #65713 ) ; +#15066 = ADVANCED_FACE ( 'NONE', ( #40725 ), #78002, .F. ) ; +#15067 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8299999999999999600 ) ) ; +#15068 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#15069 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992895, 3.500000000000000444, -1.195472123049164304E-89 ) ) ; +#15070 = AXIS2_PLACEMENT_3D ( 'NONE', #16816, #39319, #9615 ) ; +#15071 = STYLED_ITEM ( 'NONE', ( #98031 ), #96743 ) ; +#15072 = ORIENTED_EDGE ( 'NONE', *, *, #55726, .F. ) ; +#15073 = EDGE_CURVE ( 'NONE', #82206, #3614, #23899, .T. ) ; +#15074 = VECTOR ( 'NONE', #92952, 1000.000000000000114 ) ; +#15075 = ORIENTED_EDGE ( 'NONE', *, *, #50733, .T. ) ; +#15076 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15077 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19525, 'distance_accuracy_value', 'NONE'); +#15078 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#15080 = FILL_AREA_STYLE ('',( #100766 ) ) ; +#15079 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#15081 = FILL_AREA_STYLE_COLOUR ( '', #46272 ) ; +#15082 = VERTEX_POINT ( 'NONE', #47868 ) ; +#15083 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#15084 = FACE_OUTER_BOUND ( 'NONE', #52379, .T. ) ; +#15085 = SURFACE_STYLE_USAGE ( .BOTH. , #306 ) ; +#15086 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15087 = STYLED_ITEM ( 'NONE', ( #89201 ), #67017 ) ; +#15088 = ORIENTED_EDGE ( 'NONE', *, *, #22404, .F. ) ; +#15089 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15090 = ORIENTED_EDGE ( 'NONE', *, *, #7577, .F. ) ; +#15091 = VERTEX_POINT ( 'NONE', #79008 ) ; +#15093 = SURFACE_STYLE_FILL_AREA ( #87117 ) ; +#15092 = LINE ( 'NONE', #55496, #82071 ) ; +#15094 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15095 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.600000000000000089, -13.40000000000000036 ) ) ; +#15096 = STYLED_ITEM ( 'NONE', ( #31103 ), #70635 ) ; +#15098 = ORIENTED_EDGE ( 'NONE', *, *, #61920, .T. ) ; +#15097 = FACE_OUTER_BOUND ( 'NONE', #31332, .T. ) ; +#15099 = MANIFOLD_SOLID_BREP ( 'ÊäÈë78', #22528 ) ; +#15100 = FILL_AREA_STYLE ('',( #83105 ) ) ; +#15101 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15102 = EDGE_LOOP ( 'NONE', ( #47111, #40296, #86239, #54979 ) ) ; +#15104 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15103 = SURFACE_STYLE_USAGE ( .BOTH. , #78447 ) ; +#15106 = ORIENTED_EDGE ( 'NONE', *, *, #56842, .T. ) ; +#15105 = VECTOR ( 'NONE', #71760, 1000.000000000000000 ) ; +#15107 = VERTEX_POINT ( 'NONE', #47353 ) ; +#15108 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#15109 = CARTESIAN_POINT ( 'NONE', ( 1.089506002794699890, -1.495173285438690103, 0.8299999999999999600 ) ) ; +#15110 = SURFACE_STYLE_USAGE ( .BOTH. , #53970 ) ; +#15111 = SURFACE_STYLE_USAGE ( .BOTH. , #62660 ) ; +#15112 = EDGE_CURVE ( 'NONE', #36433, #95875, #80036, .T. ) ; +#15113 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#15114 = STYLED_ITEM ( 'NONE', ( #28414 ), #52381 ) ; +#15115 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15116 = EDGE_CURVE ( 'NONE', #19627, #36185, #86145, .T. ) ; +#15118 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18589 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57127, #3486, #50965 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15117 = FACE_OUTER_BOUND ( 'NONE', #32477, .T. ) ; +#15119 = VECTOR ( 'NONE', #23924, 1000.000000000000000 ) ; +#15120 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8648700000000000276 ) ) ; +#15121 = ORIENTED_EDGE ( 'NONE', *, *, #65306, .T. ) ; +#15122 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15123 = ORIENTED_EDGE ( 'NONE', *, *, #16834, .F. ) ; +#15124 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18439 ), #25049 ) ; +#15125 = PLANE ( 'NONE', #40836 ) ; +#15126 = FILL_AREA_STYLE ('',( #22850 ) ) ; +#15127 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, 1.149999999999999911 ) ) ; +#15128 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15129 = VECTOR ( 'NONE', #77331, 1000.000000000000000 ) ; +#15130 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33959 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18450, #58323, #4639 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15131 = FACE_OUTER_BOUND ( 'NONE', #87976, .T. ) ; +#15132 = VECTOR ( 'NONE', #48791, 1000.000000000000000 ) ; +#15133 = SURFACE_STYLE_USAGE ( .BOTH. , #29979 ) ; +#15134 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15135 = ORIENTED_EDGE ( 'NONE', *, *, #78463, .F. ) ; +#15136 = ADVANCED_FACE ( 'NONE', ( #62697 ), #8971, .T. ) ; +#15138 = VECTOR ( 'NONE', #49297, 1000.000000000000000 ) ; +#15137 = FILL_AREA_STYLE ('',( #83642 ) ) ; +#15139 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41111 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57685, #72441, #87267 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15141 = PRESENTATION_STYLE_ASSIGNMENT (( #62190 ) ) ; +#15142 = SURFACE_STYLE_USAGE ( .BOTH. , #54524 ) ; +#15143 = LINE ( 'NONE', #14639, #88809 ) ; +#15144 = SURFACE_STYLE_FILL_AREA ( #78480 ) ; +#15145 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71733 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90828, #60708, #6968 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15146 = SURFACE_STYLE_FILL_AREA ( #6464 ) ; +#15147 = EDGE_CURVE ( 'NONE', #73738, #39329, #35588, .T. ) ; +#15148 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.000000000000000000 ) ) ; +#15149 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15150 = SURFACE_STYLE_FILL_AREA ( #85134 ) ; +#15151 = EDGE_CURVE ( 'NONE', #19280, #81228, #80535, .T. ) ; +#15152 = VECTOR ( 'NONE', #24979, 1000.000000000000000 ) ; +#15153 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#15154 = STYLED_ITEM ( 'NONE', ( #81416 ), #9481 ) ; +#15155 = SURFACE_SIDE_STYLE ('',( #85138 ) ) ; +#15156 = CARTESIAN_POINT ( 'NONE', ( 1.286377402956589977, -0.9766832120545909657, 0.8299999999999995159 ) ) ; +#15157 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#15158 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#15159 = VERTEX_POINT ( 'NONE', #96308 ) ; +#15160 = SURFACE_SIDE_STYLE ('',( #91796 ) ) ; +#15161 = SURFACE_SIDE_STYLE ('',( #85143 ) ) ; +#15162 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#15163 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39631 ), #51108 ) ; +#15164 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#15165 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 15.15000000000000036, 0.000000000000000000 ) ) ; +#15166 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15167 = FILL_AREA_STYLE ('',( #23386 ) ) ; +#15168 = ADVANCED_FACE ( 'NONE', ( #19737 ), #25913, .T. ) ; +#15169 = EDGE_LOOP ( 'NONE', ( #68853, #74143, #25228, #69968 ) ) ; +#15170 = PLANE ( 'NONE', #53676 ) ; +#15171 = PLANE ( 'NONE', #51062 ) ; +#15172 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15173 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83752 ) ) ; +#15174 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#15175 = EDGE_CURVE ( 'NONE', #43003, #2230, #76393, .T. ) ; +#15176 = ORIENTED_EDGE ( 'NONE', *, *, #40048, .F. ) ; +#15177 = ORIENTED_EDGE ( 'NONE', *, *, #53408, .T. ) ; +#15178 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#15179 = ORIENTED_EDGE ( 'NONE', *, *, #80265, .F. ) ; +#15180 = DIRECTION ( 'NONE', ( -1.000000000000000000, -6.179952383168509971E-14, -0.000000000000000000 ) ) ; +#15181 = ADVANCED_FACE ( 'NONE', ( #49374 ), #57567, .T. ) ; +#15182 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#15183 = VECTOR ( 'NONE', #89071, 1000.000000000000000 ) ; +#15184 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000006856, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#15185 = PRESENTATION_STYLE_ASSIGNMENT (( #46865 ) ) ; +#15186 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15187 = PRODUCT_CONTEXT ( 'NONE', #91832, 'mechanical' ) ; +#15188 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#15189 = SURFACE_STYLE_USAGE ( .BOTH. , #16213 ) ; +#15191 = VERTEX_POINT ( 'NONE', #28405 ) ; +#15190 = ORIENTED_EDGE ( 'NONE', *, *, #59003, .T. ) ; +#15192 = EDGE_CURVE ( 'NONE', #77162, #70604, #21055, .T. ) ; +#15193 = ORIENTED_EDGE ( 'NONE', *, *, #72419, .F. ) ; +#15194 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15196 = VECTOR ( 'NONE', #50025, 1000.000000000000000 ) ; +#15195 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72452, 'distance_accuracy_value', 'NONE'); +#15197 = AXIS2_PLACEMENT_3D ( 'NONE', #72865, #34080, #65192 ) ; +#15198 = CARTESIAN_POINT ( 'NONE', ( 1.736267301452500300, -1.505252428432260148, 0.8100000000000000533 ) ) ; +#15199 = ORIENTED_EDGE ( 'NONE', *, *, #24083, .F. ) ; +#15200 = ADVANCED_FACE ( 'NONE', ( #30370 ), #21729, .T. ) ; +#15201 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67277 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8958, #23887, #80024 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15202 = ORIENTED_EDGE ( 'NONE', *, *, #23808, .T. ) ; +#15203 = MANIFOLD_SOLID_BREP ( 'ÊäÈë158', #17550 ) ; +#15204 = SURFACE_STYLE_USAGE ( .BOTH. , #85186 ) ; +#15205 = STYLED_ITEM ( 'NONE', ( #24603 ), #38091 ) ; +#15206 = VECTOR ( 'NONE', #69393, 1000.000000000000000 ) ; +#15207 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#15209 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15208 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15210 = ORIENTED_EDGE ( 'NONE', *, *, #89627, .T. ) ; +#15211 = FILL_AREA_STYLE ('',( #434 ) ) ; +#15212 = ORIENTED_EDGE ( 'NONE', *, *, #30891, .F. ) ; +#15213 = EDGE_CURVE ( 'NONE', #7596, #13287, #98762, .T. ) ; +#15214 = AXIS2_PLACEMENT_3D ( 'NONE', #100615, #32709, #17860 ) ; +#15215 = VERTEX_POINT ( 'NONE', #76868 ) ; +#15216 = ADVANCED_FACE ( 'NONE', ( #5373 ), #36585, .T. ) ; +#15217 = CARTESIAN_POINT ( 'NONE', ( 0.2414713305586040082, -1.411255840060410049, 0.8300000000000004041 ) ) ; +#15218 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15219 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#15220 = SURFACE_STYLE_FILL_AREA ( #38750 ) ; +#15223 = EDGE_CURVE ( 'NONE', #78683, #24202, #38569, .T. ) ; +#15222 = VERTEX_POINT ( 'NONE', #31920 ) ; +#15221 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15224 = EDGE_CURVE ( 'NONE', #76430, #33464, #94169, .T. ) ; +#15225 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 5.373192999999999664, 0.8648700000000000276 ) ) ; +#15226 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15227 = ORIENTED_EDGE ( 'NONE', *, *, #20884, .F. ) ; +#15229 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15228 = CARTESIAN_POINT ( 'NONE', ( -0.9938630133853432191, 2.355709075926970097, 0.8100000000000000533 ) ) ; +#15230 = SURFACE_STYLE_FILL_AREA ( #68866 ) ; +#15231 = ORIENTED_EDGE ( 'NONE', *, *, #1401, .F. ) ; +#15232 = ORIENTED_EDGE ( 'NONE', *, *, #88365, .F. ) ; +#15234 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#15233 = CARTESIAN_POINT ( 'NONE', ( -0.8110130133854057677, 2.061746575926969971, 0.8299999999999999600 ) ) ; +#15235 = FILL_AREA_STYLE ('',( #68870 ) ) ; +#15236 = SURFACE_SIDE_STYLE ('',( #8529 ) ) ; +#15237 = EDGE_CURVE ( 'NONE', #9920, #34710, #86034, .T. ) ; +#15238 = VECTOR ( 'NONE', #84422, 1000.000000000000000 ) ; +#15239 = PRESENTATION_STYLE_ASSIGNMENT (( #12708 ) ) ; +#15240 = EDGE_CURVE ( 'NONE', #49062, #73556, #62082, .T. ) ; +#15241 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15242 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15243 = CARTESIAN_POINT ( 'NONE', ( 0.9822218282947740020, -1.079235908285120171, 0.8299999999999997380 ) ) ; +#15245 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980549, 0.000000000000000000 ) ) ; +#15244 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33573, 'distance_accuracy_value', 'NONE'); +#15246 = CARTESIAN_POINT ( 'NONE', ( 0.1950603093179809899, -0.9901296077683260366, 0.8300000000000020695 ) ) ; +#15247 = EDGE_LOOP ( 'NONE', ( #51468, #85656, #31727, #60749, #34754, #18232, #7235, #69195, #65472, #73306 ) ) ; +#15248 = CARTESIAN_POINT ( 'NONE', ( 0.07312563425034800113, -1.247909878090150082, 0.8299999999999999600 ) ) ; +#15249 = ORIENTED_EDGE ( 'NONE', *, *, #65415, .F. ) ; +#15250 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44643 ), #629 ) ; +#15251 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15252 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15253 = SURFACE_SIDE_STYLE ('',( #15775 ) ) ; +#15254 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15255 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42766 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8743, #63977, #94587 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15257 = FILL_AREA_STYLE ('',( #84740 ) ) ; +#15256 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999578 ) ) ; +#15258 = CARTESIAN_POINT ( 'NONE', ( 1.769936080281629964, -0.9872600217210630857, 0.8100000000000000533 ) ) ; +#15259 = SURFACE_STYLE_FILL_AREA ( #8052 ) ; +#15260 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15261 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15262 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15263 = PLANE ( 'NONE', #43948 ) ; +#15264 = VECTOR ( 'NONE', #52741, 1000.000000000000000 ) ; +#15265 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#15266 = FACE_OUTER_BOUND ( 'NONE', #77152, .T. ) ; +#15267 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15268 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91639 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13267, #84307, #44967 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15270 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#15269 = VECTOR ( 'NONE', #90138, 1000.000000000000114 ) ; +#15271 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.000000000000000000 ) ) ; +#15272 = EDGE_CURVE ( 'NONE', #95021, #16753, #14837, .T. ) ; +#15273 = PLANE ( 'NONE', #4440 ) ; +#15274 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15275 = EDGE_CURVE ( 'NONE', #26002, #71809, #79477, .T. ) ; +#15277 = ORIENTED_EDGE ( 'NONE', *, *, #97370, .F. ) ; +#15276 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15278 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.000000000000000000 ) ) ; +#15279 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70161, 'distance_accuracy_value', 'NONE'); +#15280 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38011, 'distance_accuracy_value', 'NONE'); +#15281 = PRESENTATION_STYLE_ASSIGNMENT (( #91427 ) ) ; +#15282 = VECTOR ( 'NONE', #61045, 1000.000000000000000 ) ; +#15283 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15284 = FACE_OUTER_BOUND ( 'NONE', #56199, .T. ) ; +#15286 = SURFACE_SIDE_STYLE ('',( #8084 ) ) ; +#15285 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59409 ) ) ; +#15287 = VECTOR ( 'NONE', #83321, 1000.000000000000000 ) ; +#15288 = EDGE_LOOP ( 'NONE', ( #4536, #89459, #86100, #29179 ) ) ; +#15289 = FACE_OUTER_BOUND ( 'NONE', #62262, .T. ) ; +#15291 = EDGE_CURVE ( 'NONE', #36263, #79801, #8847, .T. ) ; +#15290 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #38524, #22701, #8794, #71175 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#15292 = ORIENTED_EDGE ( 'NONE', *, *, #86173, .T. ) ; +#15293 = SURFACE_SIDE_STYLE ('',( #69948 ) ) ; +#15294 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49806, 'distance_accuracy_value', 'NONE'); +#15295 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47332, 'distance_accuracy_value', 'NONE'); +#15296 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85447 ) ) ; +#15297 = PLANE ( 'NONE', #34947 ) ; +#15298 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#15299 = SURFACE_STYLE_FILL_AREA ( #90949 ) ; +#15300 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15301 = STYLED_ITEM ( 'NONE', ( #33904 ), #11946 ) ; +#15302 = FILL_AREA_STYLE ('',( #55695 ) ) ; +#15303 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15304 = SURFACE_STYLE_USAGE ( .BOTH. , #37835 ) ; +#15305 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33379 ), #62678 ) ; +#15306 = ORIENTED_EDGE ( 'NONE', *, *, #7541, .T. ) ; +#15307 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#15309 = EDGE_CURVE ( 'NONE', #76154, #88364, #61217, .T. ) ; +#15308 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15310 = DIRECTION ( 'NONE', ( 3.399536532815460200E-14, -7.018111866568259778E-13, -1.000000000000000000 ) ) ; +#15311 = VERTEX_POINT ( 'NONE', #46709 ) ; +#15312 = FILL_AREA_STYLE_COLOUR ( '', #39295 ) ; +#15313 = VECTOR ( 'NONE', #14302, 1000.000000000000000 ) ; +#15314 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#15315 = VERTEX_POINT ( 'NONE', #71222 ) ; +#15316 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15317 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20237 ) ) ; +#15318 = CARTESIAN_POINT ( 'NONE', ( 1.145723413874399910, -1.437310919031880241, 0.8100000000000000533 ) ) ; +#15319 = PRESENTATION_STYLE_ASSIGNMENT (( #45956 ) ) ; +#15320 = SURFACE_STYLE_USAGE ( .BOTH. , #9633 ) ; +#15321 = CARTESIAN_POINT ( 'NONE', ( 6.278880000000000905, 12.27581999999999951, 0.8991599999999999593 ) ) ; +#15322 = SURFACE_STYLE_USAGE ( .BOTH. , #31690 ) ; +#15323 = PLANE ( 'NONE', #13092 ) ; +#15324 = CARTESIAN_POINT ( 'NONE', ( 0.1681092235270899293, 0.6986493329168336208, 0.8100000000000001643 ) ) ; +#15327 = ORIENTED_EDGE ( 'NONE', *, *, #93010, .T. ) ; +#15326 = ORIENTED_EDGE ( 'NONE', *, *, #55157, .T. ) ; +#15325 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46307 ), #100080 ) ; +#15328 = EDGE_CURVE ( 'NONE', #92216, #17890, #7838, .T. ) ; +#15329 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#15330 = VERTEX_POINT ( 'NONE', #70196 ) ; +#15331 = VECTOR ( 'NONE', #542, 1000.000000000000000 ) ; +#15333 = CARTESIAN_POINT ( 'NONE', ( -0.4563726483146510193, -1.022509610276640002, 0.8100000000000000533 ) ) ; +#15332 = LINE ( 'NONE', #46494, #19778 ) ; +#15334 = ORIENTED_EDGE ( 'NONE', *, *, #19977, .T. ) ; +#15335 = ADVANCED_FACE ( 'NONE', ( #262 ), #16064, .T. ) ; +#15336 = VERTEX_POINT ( 'NONE', #48774 ) ; +#15337 = LINE ( 'NONE', #54714, #44804 ) ; +#15338 = FILL_AREA_STYLE ('',( #38870 ) ) ; +#15339 = AXIS2_PLACEMENT_3D ( 'NONE', #83139, #64424, #87393 ) ; +#15340 = PRESENTATION_STYLE_ASSIGNMENT (( #85313 ) ) ; +#15341 = FILL_AREA_STYLE_COLOUR ( '', #72516 ) ; +#15342 = FILL_AREA_STYLE ('',( #38380 ) ) ; +#15343 = ORIENTED_EDGE ( 'NONE', *, *, #24565, .F. ) ; +#15344 = ORIENTED_EDGE ( 'NONE', *, *, #71406, .F. ) ; +#15345 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15346 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15347 = VERTEX_POINT ( 'NONE', #11857 ) ; +#15348 = ADVANCED_FACE ( 'NONE', ( #74246 ), #65569, .T. ) ; +#15349 = SURFACE_SIDE_STYLE ('',( #79719 ) ) ; +#15350 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54556 ), #48058 ) ; +#15353 = EDGE_CURVE ( 'NONE', #68649, #19992, #25790, .T. ) ; +#15352 = EDGE_LOOP ( 'NONE', ( #64962, #85259, #78911, #31559 ) ) ; +#15351 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15354 = VECTOR ( 'NONE', #81643, 1000.000000000000000 ) ; +#15356 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15355 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15357 = SURFACE_SIDE_STYLE ('',( #31721 ) ) ; +#15358 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15359 = ORIENTED_EDGE ( 'NONE', *, *, #22343, .T. ) ; +#15361 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#15360 = VECTOR ( 'NONE', #26665, 1000.000000000000000 ) ; +#15362 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597380222, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#15363 = EDGE_LOOP ( 'NONE', ( #78795, #23331, #34234, #64644 ) ) ; +#15364 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#15366 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14998 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9331, #34935, #18570 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15365 = VECTOR ( 'NONE', #77284, 1000.000000000000114 ) ; +#15367 = SURFACE_STYLE_FILL_AREA ( #16884 ) ; +#15368 = EDGE_CURVE ( 'NONE', #16445, #59629, #66572, .T. ) ; +#15369 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#15370 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40767 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12842, #6190, #44048 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15372 = VERTEX_POINT ( 'NONE', #97673 ) ; +#15371 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.366666666666666696, 0.000000000000000000 ) ) ; +#15373 = EDGE_CURVE ( 'NONE', #1354, #98407, #65077, .T. ) ; +#15374 = VECTOR ( 'NONE', #4195, 1000.000000000000000 ) ; +#15375 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#15376 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15378 = CARTESIAN_POINT ( 'NONE', ( 1.631872624588970089, -1.500900992704750081, 0.8299999999999999600 ) ) ; +#15377 = SURFACE_STYLE_USAGE ( .BOTH. , #77181 ) ; +#15379 = CARTESIAN_POINT ( 'NONE', ( -1.034911174001889478, -1.183201991847932177, 0.8099999999998532818 ) ) ; +#15380 = FILL_AREA_STYLE ('',( #19166 ) ) ; +#15381 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15382 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#15383 = VERTEX_POINT ( 'NONE', #89070 ) ; +#15384 = VECTOR ( 'NONE', #11536, 1000.000000000000000 ) ; +#15385 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#15386 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15387 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#15389 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100748 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43422, #35799, #50118 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15388 = FACE_OUTER_BOUND ( 'NONE', #75940, .T. ) ; +#15390 = PLANE ( 'NONE', #100541 ) ; +#15392 = FILL_AREA_STYLE_COLOUR ( '', #55739 ) ; +#15391 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#15393 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15394 = MANIFOLD_SOLID_BREP ( 'ÊäÈë72', #47018 ) ; +#15395 = AXIS2_PLACEMENT_3D ( 'NONE', #28076, #90333, #65865 ) ; +#15396 = PRESENTATION_STYLE_ASSIGNMENT (( #85366 ) ) ; +#15397 = SURFACE_SIDE_STYLE ('',( #100558 ) ) ; +#15398 = EDGE_LOOP ( 'NONE', ( #22295, #9936, #43905, #66775 ) ) ; +#15399 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15400 = EDGE_LOOP ( 'NONE', ( #80542, #8012, #6363, #77307 ) ) ; +#15401 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#15402 = VECTOR ( 'NONE', #33016, 1000.000000000000000 ) ; +#15404 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#15403 = CARTESIAN_POINT ( 'NONE', ( 5.540517124874957844, 8.802661124874957110, 0.8991599999999999593 ) ) ; +#15405 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#15406 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15407 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15408 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30282 ), #64359 ) ; +#15409 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15410 = EDGE_CURVE ( 'NONE', #9892, #56832, #67555, .T. ) ; +#15411 = VERTEX_POINT ( 'NONE', #42604 ) ; +#15412 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#15413 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.004999999999999959338, -0.1499999999999999944 ) ) ; +#15414 = PLANE ( 'NONE', #91394 ) ; +#15415 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.000000000000000000 ) ) ; +#15416 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#15417 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5277 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16163, #56550, #87657 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15418 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#15419 = LINE ( 'NONE', #70571, #68122 ) ; +#15420 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#15421 = LINE ( 'NONE', #38938, #81775 ) ; +#15422 = LINE ( 'NONE', #46579, #6620 ) ; +#15423 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15424 = CARTESIAN_POINT ( 'NONE', ( 0.06276991512889880387, -1.007076035477679987, 0.8100000000000000533 ) ) ; +#15425 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #63623, #77662 ), + ( #68477, #36863 ), + ( #22023, #35001 ), + ( #67467, #84317 ), + ( #60371, #30172 ), + ( #76152, #13278 ), + ( #21522, #83822 ), + ( #6633, #76649 ), + ( #98541, #23052 ), + ( #91475, #61375 ), + ( #61858, #85308 ), + ( #54186, #14318 ), + ( #15333, #28685 ), + ( #22527, #52686 ), + ( #53682, #84805 ), + ( #38370, #14818 ), + ( #68963, #77151 ), + ( #46495, #92452 ), + ( #45465, #59875 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.08461089000532889814, 0.1632128939529030043, 0.2362131193928710127, 0.3051509900161449851, 0.3686700695782280102, 0.4293494133118639922, 0.4861986703942500210, 0.5406859797933839529, 0.5943328543671410058, 0.6474581698419740183, 0.7004632385553509755, 0.7552760594517600179, 0.8121117097227790183, 0.8714017211624900394, 0.9340348651972389948, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#15426 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15427 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25350, 'distance_accuracy_value', 'NONE'); +#15428 = FILL_AREA_STYLE ('',( #23628 ) ) ; +#15429 = PLANE ( 'NONE', #4648 ) ; +#15430 = VERTEX_POINT ( 'NONE', #91066 ) ; +#15431 = ORIENTED_EDGE ( 'NONE', *, *, #89368, .F. ) ; +#15432 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15433 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64893, 'distance_accuracy_value', 'NONE'); +#15434 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87463, 'distance_accuracy_value', 'NONE'); +#15435 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988232, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#15436 = AXIS2_PLACEMENT_3D ( 'NONE', #54513, #30999, #46806 ) ; +#15437 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26934 ), #33426 ) ; +#15438 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15439 = DIRECTION ( 'NONE', ( 0.7071067816865476141, -0.7071067806865475314, 0.000000000000000000 ) ) ; +#15440 = VERTEX_POINT ( 'NONE', #53274 ) ; +#15441 = SURFACE_SIDE_STYLE ('',( #94037 ) ) ; +#15442 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#15443 = ADVANCED_FACE ( 'NONE', ( #51274 ), #92041, .F. ) ; +#15444 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96628, 'distance_accuracy_value', 'NONE'); +#15446 = AXIS2_PLACEMENT_3D ( 'NONE', #81368, #3717, #34890 ) ; +#15445 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#15447 = ORIENTED_EDGE ( 'NONE', *, *, #6249, .F. ) ; +#15448 = SURFACE_STYLE_FILL_AREA ( #77764 ) ; +#15449 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17134 ), #2447 ) ; +#15450 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15451 = ORIENTED_EDGE ( 'NONE', *, *, #7582, .F. ) ; +#15452 = DIRECTION ( 'NONE', ( -0.3438200982495990266, 0.000000000000000000, 0.9390355371548171348 ) ) ; +#15453 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43875, #83699, #60244 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15454 = LINE ( 'NONE', #77771, #15238 ) ; +#15455 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15456 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15457 = ORIENTED_EDGE ( 'NONE', *, *, #67711, .F. ) ; +#15458 = VECTOR ( 'NONE', #8895, 1000.000000000000000 ) ; +#15459 = CARTESIAN_POINT ( 'NONE', ( 4.409146875125044218, 7.671290875125043485, 0.8991599999999999593 ) ) ; +#15460 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27183, 'distance_accuracy_value', 'NONE'); +#15461 = CARTESIAN_POINT ( 'NONE', ( 0.6316964285714280480, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#15462 = FACE_OUTER_BOUND ( 'NONE', #28001, .T. ) ; +#15463 = EDGE_CURVE ( 'NONE', #76986, #48454, #77750, .T. ) ; +#15464 = ORIENTED_EDGE ( 'NONE', *, *, #93621, .T. ) ; +#15465 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72566 ), #13759 ) ; +#15466 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15467 = VERTEX_POINT ( 'NONE', #9233 ) ; +#15469 = EDGE_LOOP ( 'NONE', ( #46976, #61250, #76505, #38253, #89249, #9536 ) ) ; +#15468 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15470 = FILL_AREA_STYLE ('',( #38491 ) ) ; +#15471 = EDGE_LOOP ( 'NONE', ( #59286, #74746, #84806, #12416, #45998, #43965, #36230, #88328 ) ) ; +#15472 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15473 = ORIENTED_EDGE ( 'NONE', *, *, #45216, .F. ) ; +#15475 = ORIENTED_EDGE ( 'NONE', *, *, #39554, .T. ) ; +#15474 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#15476 = EDGE_CURVE ( 'NONE', #79706, #82518, #31278, .T. ) ; +#15477 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15478 = DIRECTION ( 'NONE', ( 0.000000000000000000, 3.355477456267752477E-13, -1.000000000000000000 ) ) ; +#15480 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#15479 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10530 ) ) ; +#15481 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#15482 = ORIENTED_EDGE ( 'NONE', *, *, #3683, .F. ) ; +#15483 = PRESENTATION_STYLE_ASSIGNMENT (( #7272 ) ) ; +#15484 = SURFACE_STYLE_FILL_AREA ( #23189 ) ; +#15485 = VERTEX_POINT ( 'NONE', #84895 ) ; +#15486 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14571, #53429, #6863 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15487 = CARTESIAN_POINT ( 'NONE', ( -0.01135318676504863157, -1.093511444119889875, 0.8100000000001061906 ) ) ; +#15488 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#15489 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15490 = VERTEX_POINT ( 'NONE', #15940 ) ; +#15491 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75874 ) ) ; +#15492 = ORIENTED_EDGE ( 'NONE', *, *, #93052, .F. ) ; +#15493 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46475 ) ) ; +#15494 = ADVANCED_FACE ( 'NONE', ( #23636 ), #55314, .F. ) ; +#15495 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#15496 = SURFACE_STYLE_FILL_AREA ( #7288 ) ; +#15497 = FILL_AREA_STYLE_COLOUR ( '', #27847 ) ; +#15498 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84223, #39249, #964, #86219 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#15499 = CARTESIAN_POINT ( 'NONE', ( 0.1485744800866570237, -1.491420757567720079, 0.8299999999999982947 ) ) ; +#15500 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77556 ) ) ; +#15501 = ORIENTED_EDGE ( 'NONE', *, *, #13763, .F. ) ; +#15502 = ORIENTED_EDGE ( 'NONE', *, *, #13729, .T. ) ; +#15503 = SURFACE_STYLE_USAGE ( .BOTH. , #85478 ) ; +#15504 = LINE ( 'NONE', #93104, #68419 ) ; +#15506 = AXIS2_PLACEMENT_3D ( 'NONE', #81126, #4964, #28484 ) ; +#15505 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54281 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11168, #28107, #14215 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15507 = AXIS2_PLACEMENT_3D ( 'NONE', #42474, #33814, #96048 ) ; +#15508 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72487, 'distance_accuracy_value', 'NONE'); +#15509 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18824 ) ) ; +#15510 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15511 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#15512 = VECTOR ( 'NONE', #24768, 1000.000000000000000 ) ; +#15513 = SURFACE_STYLE_FILL_AREA ( #85486 ) ; +#15514 = PRESENTATION_STYLE_ASSIGNMENT (( #56413 ) ) ; +#15515 = EDGE_LOOP ( 'NONE', ( #63717, #57638, #48278, #14925 ) ) ; +#15516 = ADVANCED_FACE ( 'NONE', ( #78752 ), #46060, .T. ) ; +#15517 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#15518 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15520 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#15519 = FILL_AREA_STYLE ('',( #14995 ) ) ; +#15521 = LINE ( 'NONE', #77842, #60234 ) ; +#15522 = CIRCLE ( 'NONE', #85674, 0.2137111836784290342 ) ; +#15523 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15524 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#15525 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8648700000000000276 ) ) ; +#15526 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #81766, #26131, #27136, #80758 ), + ( #88906, #65928, #17914, #27643 ), + ( #41947, #57797, #58798, #66910 ), + ( #73078, #11695, #73581, #58301 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#15527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15528 = EDGE_CURVE ( 'NONE', #85953, #55224, #6372, .T. ) ; +#15529 = VERTEX_POINT ( 'NONE', #47617 ) ; +#15530 = SURFACE_STYLE_USAGE ( .BOTH. , #40067 ) ; +#15531 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15532 = SURFACE_STYLE_FILL_AREA ( #78370 ) ; +#15533 = SURFACE_STYLE_USAGE ( .BOTH. , #69670 ) ; +#15534 = SURFACE_STYLE_FILL_AREA ( #38555 ) ; +#15535 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77286 ), #90579 ) ; +#15536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15537 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15538 = LINE ( 'NONE', #85006, #16473 ) ; +#15539 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#15540 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15541 = SURFACE_STYLE_FILL_AREA ( #87541 ) ; +#15542 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#15543 = LINE ( 'NONE', #54403, #25618 ) ; +#15544 = LINE ( 'NONE', #7330, #43930 ) ; +#15545 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#15546 = VERTEX_POINT ( 'NONE', #8716 ) ; +#15547 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59130, 'distance_accuracy_value', 'NONE'); +#15548 = FILL_AREA_STYLE ('',( #47740 ) ) ; +#15549 = CARTESIAN_POINT ( 'NONE', ( -0.1767776940718484846, -1.506231469368489728, 0.8099999999994900168 ) ) ; +#15550 = STYLED_ITEM ( 'NONE', ( #26483 ), #83276 ) ; +#15551 = AXIS2_PLACEMENT_3D ( 'NONE', #13901, #45067, #6231 ) ; +#15552 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35637 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25628, #16913, #31250 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15553 = CARTESIAN_POINT ( 'NONE', ( -0.8116130133853437512, 1.464409075926257131, 0.8299999999999999600 ) ) ; +#15554 = LINE ( 'NONE', #46715, #97225 ) ; +#15555 = CARTESIAN_POINT ( 'NONE', ( -1.233538577444069917, -1.130592060098940088, 0.8100000000000000533 ) ) ; +#15556 = ORIENTED_EDGE ( 'NONE', *, *, #36996, .T. ) ; +#15557 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#15558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46548 ) ) ; +#15559 = MANIFOLD_SOLID_BREP ( 'ÊäÈë54', #30588 ) ; +#15560 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15561 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82480, 'distance_accuracy_value', 'NONE'); +#15563 = FILL_AREA_STYLE_COLOUR ( '', #67339 ) ; +#15562 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51497 ) ) ; +#15564 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15565 = VECTOR ( 'NONE', #73282, 1000.000000000000000 ) ; +#15566 = ORIENTED_EDGE ( 'NONE', *, *, #87479, .T. ) ; +#15567 = FILL_AREA_STYLE ('',( #85541 ) ) ; +#15568 = EDGE_CURVE ( 'NONE', #26843, #62242, #39962, .T. ) ; +#15569 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15570 = SURFACE_SIDE_STYLE ('',( #39092 ) ) ; +#15571 = CARTESIAN_POINT ( 'NONE', ( -0.03713474025974040221, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#15572 = STYLED_ITEM ( 'NONE', ( #60735 ), #77621 ) ; +#15573 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#15574 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, 0.000000000000000000 ) ) ; +#15575 = ORIENTED_EDGE ( 'NONE', *, *, #17278, .T. ) ; +#15576 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#15577 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15578 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93831, 'distance_accuracy_value', 'NONE'); +#15579 = AXIS2_PLACEMENT_3D ( 'NONE', #8588, #69434, #38832 ) ; +#15580 = LINE ( 'NONE', #92195, #13213 ) ; +#15581 = VECTOR ( 'NONE', #11739, 1000.000000000000000 ) ; +#15582 = LINE ( 'NONE', #85551, #12699 ) ; +#15583 = EDGE_CURVE ( 'NONE', #1370, #83734, #9736, .T. ) ; +#15584 = ORIENTED_EDGE ( 'NONE', *, *, #73224, .F. ) ; +#15585 = EDGE_CURVE ( 'NONE', #65258, #100078, #34342, .T. ) ; +#15586 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38952 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49451, #95878, #19811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15587 = STYLED_ITEM ( 'NONE', ( #35593 ), #99568 ) ; +#15588 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15589 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000001235, -0.1350000000000000089 ) ) ; +#15590 = ORIENTED_EDGE ( 'NONE', *, *, #94350, .T. ) ; +#15591 = DIRECTION ( 'NONE', ( 0.7071067811865470176, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#15592 = CARTESIAN_POINT ( 'NONE', ( 0.08972571571753010233, -1.370875895369189967, 0.8299999999999999600 ) ) ; +#15593 = CARTESIAN_POINT ( 'NONE', ( 0.5010457827341869841, -1.198290873665909917, 0.8100000000000000533 ) ) ; +#15594 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#15595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8986 ), #33586 ) ; +#15596 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #74413, #100314 ) ; +#15597 = CARTESIAN_POINT ( 'NONE', ( 0.2416038136213350396, -1.101447087279459947, 0.8100000000000000533 ) ) ; +#15598 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59714 ), #71102 ) ; +#15599 = ORIENTED_EDGE ( 'NONE', *, *, #54628, .T. ) ; +#15600 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15602 = ADVANCED_FACE ( 'NONE', ( #97065 ), #10220, .T. ) ; +#15601 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87427 ) ) ; +#15603 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.000000000000000000 ) ) ; +#15604 = SURFACE_STYLE_USAGE ( .BOTH. , #61623 ) ; +#15605 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#15606 = ORIENTED_EDGE ( 'NONE', *, *, #95017, .F. ) ; +#15607 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15608 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #83756, #3253, #43054, #34426, #96651, #57926, #13737, #76085, #19054, #44907, #50259, #89538, #6072, #21958, #37308, #68409, #29613, #60795, #33918 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.493776705857522183E-05, 4.937248302705437685E-05, 7.331477681365963144E-05, 9.701993325366111884E-05, 0.0001201633963783052273, 0.0001426908098046692083, 0.0001647393961703016519, 0.0001865685712343123409, 0.0002082099287761336910, 0.0002296593890597261451, 0.0002512893635836990357, 0.0002733379499493311269, 0.0002960714739221034027, 0.0003197202093211130229, 0.0003446878849621071096, 0.0003712273557114585134 ), + .UNSPECIFIED. ) ; +#15609 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15610 = ORIENTED_EDGE ( 'NONE', *, *, #7003, .F. ) ; +#15611 = VECTOR ( 'NONE', #78959, 1000.000000000000000 ) ; +#15612 = SURFACE_SIDE_STYLE ('',( #30425 ) ) ; +#15613 = ORIENTED_EDGE ( 'NONE', *, *, #68674, .T. ) ; +#15614 = ORIENTED_EDGE ( 'NONE', *, *, #85411, .F. ) ; +#15615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15616 = ADVANCED_FACE ( 'NONE', ( #42971 ), #41481, .F. ) ; +#15617 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #85938, #5682 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #9887 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#15618 = LINE ( 'NONE', #7400, #71774 ) ; +#15619 = ORIENTED_EDGE ( 'NONE', *, *, #87644, .F. ) ; +#15620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15621 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#15622 = SURFACE_SIDE_STYLE ('',( #49214 ) ) ; +#15623 = ORIENTED_EDGE ( 'NONE', *, *, #85835, .T. ) ; +#15625 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15624 = SURFACE_STYLE_FILL_AREA ( #23332 ) ; +#15626 = VERTEX_POINT ( 'NONE', #82785 ) ; +#15627 = ORIENTED_EDGE ( 'NONE', *, *, #80725, .T. ) ; +#15628 = LINE ( 'NONE', #54490, #58461 ) ; +#15629 = LINE ( 'NONE', #30446, #58573 ) ; +#15630 = STYLED_ITEM ( 'NONE', ( #22667 ), #49616 ) ; +#15631 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15632 = FILL_AREA_STYLE ('',( #47311 ) ) ; +#15633 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15635 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15636 = VECTOR ( 'NONE', #27076, 1000.000000000000000 ) ; +#15637 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100940 ) ; +#15638 = FILL_AREA_STYLE_COLOUR ( '', #71997 ) ; +#15639 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#15640 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15641 = EDGE_LOOP ( 'NONE', ( #37173, #64025, #94055, #36974 ) ) ; +#15642 = ADVANCED_FACE ( 'NONE', ( #59848 ), #75619, .T. ) ; +#15643 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72757 ), #76024 ) ; +#15644 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15646 = FILL_AREA_STYLE_COLOUR ( '', #70344 ) ; +#15645 = SURFACE_STYLE_FILL_AREA ( #47833 ) ; +#15647 = FILL_AREA_STYLE_COLOUR ( '', #31837 ) ; +#15648 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109696999999998823, 0.8648700000000000276 ) ) ; +#15649 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15650 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.233333333333333393, 0.000000000000000000 ) ) ; +#15651 = FILL_AREA_STYLE ('',( #69788 ) ) ; +#15652 = SURFACE_STYLE_FILL_AREA ( #53991 ) ; +#15653 = SURFACE_STYLE_FILL_AREA ( #92752 ) ; +#15654 = ADVANCED_FACE ( 'NONE', ( #68442 ), #51671, .F. ) ; +#15655 = EDGE_LOOP ( 'NONE', ( #66141, #73533, #45347, #42527 ) ) ; +#15656 = VECTOR ( 'NONE', #80359, 1000.000000000000000 ) ; +#15657 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15658 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59773 ) ) ; +#15659 = LINE ( 'NONE', #60192, #43072 ) ; +#15660 = CARTESIAN_POINT ( 'NONE', ( -0.4373985389610389740, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#15661 = SURFACE_SIDE_STYLE ('',( #53008 ) ) ; +#15662 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15663 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68342, 'distance_accuracy_value', 'NONE'); +#15664 = EDGE_CURVE ( 'NONE', #38462, #22291, #58844, .T. ) ; +#15665 = SURFACE_STYLE_USAGE ( .BOTH. , #85641 ) ; +#15666 = AXIS2_PLACEMENT_3D ( 'NONE', #3044, #80169, #19358 ) ; +#15667 = SURFACE_STYLE_USAGE ( .BOTH. , #30475 ) ; +#15668 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1400000000000000133 ) ) ; +#15669 = SURFACE_STYLE_USAGE ( .BOTH. , #63203 ) ; +#15670 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2669 ) ) ; +#15671 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8648700000000000276 ) ) ; +#15672 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15673 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15675 = EDGE_CURVE ( 'NONE', #33923, #28348, #12761, .T. ) ; +#15676 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#15677 = FILL_AREA_STYLE ('',( #54536 ) ) ; +#15678 = FILL_AREA_STYLE_COLOUR ( '', #89679 ) ; +#15679 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #10953, 'design' ) ; +#15680 = PLANE ( 'NONE', #14263 ) ; +#15681 = DIRECTION ( 'NONE', ( -2.258754526011470139E-17, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15682 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15683 = EDGE_LOOP ( 'NONE', ( #38039, #17869, #74283, #75950 ) ) ; +#15684 = FILL_AREA_STYLE ('',( #46318 ) ) ; +#15685 = FILL_AREA_STYLE_COLOUR ( '', #12158 ) ; +#15686 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#15687 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8023, 'distance_accuracy_value', 'NONE'); +#15688 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#15689 = CIRCLE ( 'NONE', #36932, 0.01000000000000002623 ) ; +#15690 = LINE ( 'NONE', #46842, #97689 ) ; +#15691 = ADVANCED_FACE ( 'NONE', ( #36827 ), #67929, .T. ) ; +#15692 = ADVANCED_FACE ( 'NONE', ( #93906 ), #38335, .F. ) ; +#15693 = CARTESIAN_POINT ( 'NONE', ( 1.810234811980210079, -1.482878949593630091, 0.8300000000000011813 ) ) ; +#15694 = DIRECTION ( 'NONE', ( -0.7071071146859688739, -0.7071064476869688420, 0.000000000000000000 ) ) ; +#15695 = VECTOR ( 'NONE', #19567, 1000.000000000000000 ) ; +#15696 = ORIENTED_EDGE ( 'NONE', *, *, #41823, .T. ) ; +#15697 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15698 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15699 = CYLINDRICAL_SURFACE ( 'NONE', #24280, 0.009999999999999998473 ) ; +#15700 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35630, 'distance_accuracy_value', 'NONE'); +#15702 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.8944271909999158554, -0.4472135954999579277 ) ) ; +#15701 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28769 ), #50027 ) ; +#15703 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61393 ), #79297 ) ; +#15704 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57220, 'distance_accuracy_value', 'NONE'); +#15705 = CYLINDRICAL_SURFACE ( 'NONE', #98961, 0.05000000000000002359 ) ; +#15706 = EDGE_CURVE ( 'NONE', #49180, #30201, #63358, .T. ) ; +#15707 = EDGE_LOOP ( 'NONE', ( #38408, #54169, #5034, #62373 ) ) ; +#15708 = ORIENTED_EDGE ( 'NONE', *, *, #64419, .F. ) ; +#15709 = EDGE_CURVE ( 'NONE', #55846, #23423, #6, .T. ) ; +#15710 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000013545, 0.1829999999999619709 ) ) ; +#15711 = ORIENTED_EDGE ( 'NONE', *, *, #40070, .T. ) ; +#15712 = LINE ( 'NONE', #52549, #39528 ) ; +#15713 = SURFACE_STYLE_FILL_AREA ( #38229 ) ; +#15714 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81545, 'distance_accuracy_value', 'NONE'); +#15715 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60710 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82685, #59242, #83197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15716 = SHAPE_DEFINITION_REPRESENTATION ( #44130, #50203 ) ; +#15717 = LINE ( 'NONE', #62738, #6722 ) ; +#15718 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15720 = ORIENTED_EDGE ( 'NONE', *, *, #34104, .T. ) ; +#15719 = ORIENTED_EDGE ( 'NONE', *, *, #88221, .T. ) ; +#15721 = AXIS2_PLACEMENT_3D ( 'NONE', #83133, #51519, #11585 ) ; +#15722 = EDGE_LOOP ( 'NONE', ( #93054, #85231, #50066, #39824, #57645, #43393 ) ) ; +#15723 = VECTOR ( 'NONE', #25520, 1000.000000000000000 ) ; +#15724 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38633 ), #9191 ) ; +#15725 = ADVANCED_FACE ( 'NONE', ( #32188 ), #31167, .T. ) ; +#15727 = FILL_AREA_STYLE_COLOUR ( '', #18677 ) ; +#15726 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15728 = ORIENTED_EDGE ( 'NONE', *, *, #9716, .F. ) ; +#15729 = MANIFOLD_SOLID_BREP ( 'ÊäÈë170', #4591 ) ; +#15730 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, -3.099999999999994316, 0.000000000000000000 ) ) ; +#15731 = EDGE_CURVE ( 'NONE', #40353, #58769, #76882, .T. ) ; +#15732 = FILL_AREA_STYLE ('',( #23427 ) ) ; +#15733 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43334 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96066, #2682, #3668 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15734 = LINE ( 'NONE', #68848, #22005 ) ; +#15735 = ORIENTED_EDGE ( 'NONE', *, *, #52582, .T. ) ; +#15736 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15737 = STYLED_ITEM ( 'NONE', ( #99743 ), #5319 ) ; +#15738 = ORIENTED_EDGE ( 'NONE', *, *, #58773, .T. ) ; +#15739 = VERTEX_POINT ( 'NONE', #64831 ) ; +#15740 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#15741 = EDGE_CURVE ( 'NONE', #74391, #83732, #19362, .T. ) ; +#15742 = CARTESIAN_POINT ( 'NONE', ( -0.5833333333333330373, -3.099999999999989875, 0.000000000000000000 ) ) ; +#15743 = FACE_OUTER_BOUND ( 'NONE', #40274, .T. ) ; +#15744 = EDGE_CURVE ( 'NONE', #28967, #49438, #1549, .T. ) ; +#15745 = CIRCLE ( 'NONE', #90784, 0.01000000000000002623 ) ; +#15746 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15748 = VERTEX_POINT ( 'NONE', #65324 ) ; +#15747 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#15749 = FILL_AREA_STYLE_COLOUR ( '', #35244 ) ; +#15750 = VECTOR ( 'NONE', #62621, 1000.000000000000000 ) ; +#15751 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15752 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15753 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15754 = EDGE_LOOP ( 'NONE', ( #17973, #51458, #7249, #39322 ) ) ; +#15755 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15756 = EDGE_LOOP ( 'NONE', ( #64255, #19012, #5287, #92021 ) ) ; +#15757 = VERTEX_POINT ( 'NONE', #80681 ) ; +#15758 = CARTESIAN_POINT ( 'NONE', ( 1.823120247820650297, -1.344848644821849959, 0.8300000000000002931 ) ) ; +#15759 = PRESENTATION_STYLE_ASSIGNMENT (( #62780 ) ) ; +#15760 = CARTESIAN_POINT ( 'NONE', ( -0.3839949111172690221, -1.170868642971409912, 0.8299999999999999600 ) ) ; +#15761 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15762 = SURFACE_STYLE_USAGE ( .BOTH. , #85727 ) ; +#15763 = PRESENTATION_STYLE_ASSIGNMENT (( #460 ) ) ; +#15764 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.3000000000000016542, 7.103537399566374497E-79 ) ) ; +#15765 = LINE ( 'NONE', #62279, #44264 ) ; +#15766 = AXIS2_PLACEMENT_3D ( 'NONE', #72435, #74478, #72958 ) ; +#15767 = VERTEX_POINT ( 'NONE', #40866 ) ; +#15768 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8299999999999999600 ) ) ; +#15769 = EDGE_CURVE ( 'NONE', #15347, #15159, #73510, .T. ) ; +#15770 = CARTESIAN_POINT ( 'NONE', ( 0.09346250786341020467, -1.325441991778449902, 0.8299999999999999600 ) ) ; +#15771 = ORIENTED_EDGE ( 'NONE', *, *, #5662, .F. ) ; +#15772 = SURFACE_STYLE_USAGE ( .BOTH. , #46412 ) ; +#15773 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#15774 = SURFACE_STYLE_USAGE ( .BOTH. , #29126 ) ; +#15775 = SURFACE_STYLE_FILL_AREA ( #25505 ) ; +#15776 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15777 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76075 ) ) ; +#15778 = FILL_AREA_STYLE ('',( #29128 ) ) ; +#15779 = PRESENTATION_STYLE_ASSIGNMENT (( #53616 ) ) ; +#15780 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#15781 = SURFACE_SIDE_STYLE ('',( #24520 ) ) ; +#15783 = ADVANCED_FACE ( 'NONE', ( #96951 ), #48530, .F. ) ; +#15782 = FACE_OUTER_BOUND ( 'NONE', #856, .T. ) ; +#15784 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15785 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15786 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15788 = FILL_AREA_STYLE ('',( #46428 ) ) ; +#15789 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28780 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5699, #92007, #83367 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15790 = EDGE_CURVE ( 'NONE', #64246, #59269, #49028, .T. ) ; +#15791 = PRESENTATION_STYLE_ASSIGNMENT (( #9085 ) ) ; +#15792 = PRESENTATION_STYLE_ASSIGNMENT (( #99479 ) ) ; +#15794 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8648700000000000276 ) ) ; +#15793 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15796 = VECTOR ( 'NONE', #26319, 1000.000000000000000 ) ; +#15795 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15797 = PRESENTATION_STYLE_ASSIGNMENT (( #80154 ) ) ; +#15798 = EDGE_CURVE ( 'NONE', #89708, #40707, #75998, .T. ) ; +#15799 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15800 = MANIFOLD_SOLID_BREP ( 'ÊäÈë79', #15872 ) ; +#15801 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59892 ) ) ; +#15802 = STYLED_ITEM ( 'NONE', ( #50807 ), #16124 ) ; +#15803 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66106, 'distance_accuracy_value', 'NONE'); +#15804 = ORIENTED_EDGE ( 'NONE', *, *, #63886, .T. ) ; +#15805 = CLOSED_SHELL ( 'NONE', ( #26761, #77698, #30499, #42859, #46120, #43294 ) ) ; +#15806 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#15807 = STYLED_ITEM ( 'NONE', ( #59573 ), #40020 ) ; +#15808 = LINE ( 'NONE', #18706, #46111 ) ; +#15809 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 1.100000000000000089, -0.02000000000001679948 ) ) ; +#15810 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58695 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18853, #11121, #4053 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15811 = LINE ( 'NONE', #68913, #58509 ) ; +#15812 = LINE ( 'NONE', #45930, #40977 ) ; +#15813 = AXIS2_PLACEMENT_3D ( 'NONE', #33719, #26561, #58233 ) ; +#15814 = EDGE_CURVE ( 'NONE', #41816, #35363, #22078, .T. ) ; +#15815 = EDGE_CURVE ( 'NONE', #99269, #93951, #67326, .T. ) ; +#15816 = VERTEX_POINT ( 'NONE', #4047 ) ; +#15817 = SURFACE_STYLE_FILL_AREA ( #37343 ) ; +#15818 = ORIENTED_EDGE ( 'NONE', *, *, #88716, .F. ) ; +#15819 = SURFACE_SIDE_STYLE ('',( #85781 ) ) ; +#15820 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15821 = FILL_AREA_STYLE ('',( #40362 ) ) ; +#15822 = SURFACE_STYLE_FILL_AREA ( #47493 ) ; +#15823 = CARTESIAN_POINT ( 'NONE', ( -0.8116236238560184946, 1.426068491040176189, 0.8100000000000000533 ) ) ; +#15824 = ORIENTED_EDGE ( 'NONE', *, *, #96203, .T. ) ; +#15825 = CARTESIAN_POINT ( 'NONE', ( 1.132978354350060224, -0.9623790331012080923, 0.8300000000000002931 ) ) ; +#15826 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15827 = FILL_AREA_STYLE ('',( #53662 ) ) ; +#15828 = VERTEX_POINT ( 'NONE', #69703 ) ; +#15829 = LINE ( 'NONE', #55203, #60479 ) ; +#15830 = ADVANCED_FACE ( 'NONE', ( #13132 ), #38582, .F. ) ; +#15831 = AXIS2_PLACEMENT_3D ( 'NONE', #1161, #32328, #21256 ) ; +#15832 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#15833 = ORIENTED_EDGE ( 'NONE', *, *, #59732, .F. ) ; +#15834 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91197 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17171, #78978, #40191 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15835 = PRESENTATION_STYLE_ASSIGNMENT (( #85802 ) ) ; +#15836 = SURFACE_SIDE_STYLE ('',( #29788 ) ) ; +#15837 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#15838 = VECTOR ( 'NONE', #48381, 1000.000000000000000 ) ; +#15839 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#15840 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#15841 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8648700000000000276 ) ) ; +#15842 = SURFACE_STYLE_FILL_AREA ( #39339 ) ; +#15844 = EDGE_LOOP ( 'NONE', ( #7503, #28462, #22557, #1972 ) ) ; +#15843 = EDGE_LOOP ( 'NONE', ( #40019, #60627, #6618, #29567, #60361, #39896 ) ) ; +#15845 = FACE_OUTER_BOUND ( 'NONE', #51806, .T. ) ; +#15846 = LINE ( 'NONE', #31695, #15331 ) ; +#15847 = ORIENTED_EDGE ( 'NONE', *, *, #45201, .F. ) ; +#15848 = SURFACE_STYLE_USAGE ( .BOTH. , #7618 ) ; +#15849 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72954 ), #1146 ) ; +#15850 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#15851 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15852 = ORIENTED_EDGE ( 'NONE', *, *, #51629, .T. ) ; +#15853 = EDGE_LOOP ( 'NONE', ( #32513, #89856, #16795, #98517, #14221, #1813, #11773, #91352 ) ) ; +#15854 = FACE_OUTER_BOUND ( 'NONE', #8646, .T. ) ; +#15855 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15856 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15857 = ORIENTED_EDGE ( 'NONE', *, *, #71763, .T. ) ; +#15858 = EDGE_LOOP ( 'NONE', ( #85475, #25967, #34938, #9418 ) ) ; +#15859 = LINE ( 'NONE', #22037, #69701 ) ; +#15860 = ORIENTED_EDGE ( 'NONE', *, *, #30783, .T. ) ; +#15861 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59955 ) ) ; +#15862 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15864 = ORIENTED_EDGE ( 'NONE', *, *, #64286, .T. ) ; +#15863 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#15865 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.005000000000000000971, 0.2500000000000000000 ) ) ; +#15866 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15868 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95747 ), #81164 ) ; +#15867 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#15869 = ORIENTED_EDGE ( 'NONE', *, *, #98585, .T. ) ; +#15870 = EDGE_CURVE ( 'NONE', #13168, #6286, #83677, .T. ) ; +#15871 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15872 = CLOSED_SHELL ( 'NONE', ( #28748, #6232, #92553, #20692, #30164, #78668 ) ) ; +#15873 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15874 = ORIENTED_EDGE ( 'NONE', *, *, #6520, .T. ) ; +#15875 = VECTOR ( 'NONE', #71461, 1000.000000000000114 ) ; +#15876 = CARTESIAN_POINT ( 'NONE', ( 0.06276991512889880387, -1.007076035477679987, 0.8299999999999988498 ) ) ; +#15877 = AXIS2_PLACEMENT_3D ( 'NONE', #81529, #19183, #64662 ) ; +#15878 = SURFACE_SIDE_STYLE ('',( #40930 ) ) ; +#15879 = SURFACE_STYLE_USAGE ( .BOTH. , #24624 ) ; +#15880 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94024 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70034, #53723, #76689 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15882 = ORIENTED_EDGE ( 'NONE', *, *, #95319, .F. ) ; +#15881 = SURFACE_STYLE_USAGE ( .BOTH. , #85853 ) ; +#15884 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#15883 = AXIS2_PLACEMENT_3D ( 'NONE', #36157, #83109, #75937 ) ; +#15885 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15887 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666653285, 0.5000000000000000000, 3.495651678170078205E-76 ) ) ; +#15886 = SURFACE_STYLE_USAGE ( .BOTH. , #19558 ) ; +#15888 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8099999999999785150 ) ) ; +#15889 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#15890 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15891 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#15892 = EDGE_CURVE ( 'NONE', #46953, #64228, #81686, .T. ) ; +#15893 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#15894 = ORIENTED_EDGE ( 'NONE', *, *, #28909, .F. ) ; +#15895 = FACE_OUTER_BOUND ( 'NONE', #97655, .T. ) ; +#15896 = LINE ( 'NONE', #78704, #53100 ) ; +#15898 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 8.003631000000000384, 0.8648700000000000276 ) ) ; +#15897 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 8.519819000000000031, 0.8648700000000000276 ) ) ; +#15899 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#15900 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999918510, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#15901 = MANIFOLD_SOLID_BREP ( 'ÊäÈë63', #33862 ) ; +#15902 = AXIS2_PLACEMENT_3D ( 'NONE', #22513, #53671, #79172 ) ; +#15903 = FILL_AREA_STYLE_COLOUR ( '', #11748 ) ; +#15904 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15905 = ORIENTED_EDGE ( 'NONE', *, *, #33396, .T. ) ; +#15906 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15907 = PRESENTATION_STYLE_ASSIGNMENT (( #16398 ) ) ; +#15908 = VERTEX_POINT ( 'NONE', #47757 ) ; +#15909 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15911 = PRESENTATION_STYLE_ASSIGNMENT (( #71590 ) ) ; +#15910 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#15912 = FILL_AREA_STYLE_COLOUR ( '', #76582 ) ; +#15913 = EDGE_CURVE ( 'NONE', #36781, #72797, #74003, .T. ) ; +#15914 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15915 = LINE ( 'NONE', #71077, #78970 ) ; +#15916 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40388 ), #87674 ) ; +#15917 = STYLED_ITEM ( 'NONE', ( #5852 ), #91072 ) ; +#15918 = FACE_OUTER_BOUND ( 'NONE', #38860, .T. ) ; +#15919 = EDGE_CURVE ( 'NONE', #89393, #28217, #17594, .T. ) ; +#15920 = ORIENTED_EDGE ( 'NONE', *, *, #55187, .T. ) ; +#15921 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#15922 = LINE ( 'NONE', #40462, #2247 ) ; +#15923 = FILL_AREA_STYLE ('',( #1656 ) ) ; +#15924 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#15925 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#15926 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#15927 = PRESENTATION_STYLE_ASSIGNMENT (( #55299 ) ) ; +#15928 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19743, #44699, #5870, #68185 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#15929 = EDGE_CURVE ( 'NONE', #53702, #60384, #24307, .T. ) ; +#15930 = SURFACE_STYLE_FILL_AREA ( #92526 ) ; +#15931 = EDGE_CURVE ( 'NONE', #13660, #30962, #94187, .T. ) ; +#15932 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73045 ) ) ; +#15933 = LINE ( 'NONE', #84886, #38924 ) ; +#15934 = VECTOR ( 'NONE', #19851, 1000.000000000000114 ) ; +#15935 = EDGE_LOOP ( 'NONE', ( #23679, #23187, #80082, #73048 ) ) ; +#15936 = SURFACE_STYLE_FILL_AREA ( #22112 ) ; +#15937 = ORIENTED_EDGE ( 'NONE', *, *, #82396, .T. ) ; +#15938 = ADVANCED_FACE ( 'NONE', ( #25312 ), #2322, .T. ) ; +#15939 = EDGE_CURVE ( 'NONE', #10921, #89369, #46724, .T. ) ; +#15940 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#15941 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#15942 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#15944 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#15943 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#15945 = LINE ( 'NONE', #95058, #71645 ) ; +#15946 = SURFACE_SIDE_STYLE ('',( #86428 ) ) ; +#15947 = AXIS2_PLACEMENT_3D ( 'NONE', #90203, #35615, #21761 ) ; +#15948 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#15949 = CARTESIAN_POINT ( 'NONE', ( 5.519304249750025093, 2.827609249750024034, 0.8991599999999999593 ) ) ; +#15950 = CLOSED_SHELL ( 'NONE', ( #42399, #76006, #51007, #92026, #20685, #13428 ) ) ; +#15951 = ORIENTED_EDGE ( 'NONE', *, *, #92573, .T. ) ; +#15952 = PRESENTATION_STYLE_ASSIGNMENT (( #47112 ) ) ; +#15953 = CIRCLE ( 'NONE', #37133, 0.009999999999999998473 ) ; +#15954 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#15955 = EDGE_LOOP ( 'NONE', ( #44850, #96286, #79549, #22764 ) ) ; +#15956 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#15957 = EDGE_CURVE ( 'NONE', #54887, #85096, #39091, .T. ) ; +#15958 = PLANE ( 'NONE', #35757 ) ; +#15959 = ORIENTED_EDGE ( 'NONE', *, *, #49653, .T. ) ; +#15960 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15961 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15962 = EDGE_CURVE ( 'NONE', #58394, #59781, #33466, .T. ) ; +#15963 = VECTOR ( 'NONE', #112, 1000.000000000000000 ) ; +#15964 = SURFACE_SIDE_STYLE ('',( #12006 ) ) ; +#15965 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#15966 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15967 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15968 = ORIENTED_EDGE ( 'NONE', *, *, #32240, .T. ) ; +#15970 = VECTOR ( 'NONE', #57440, 1000.000000000000114 ) ; +#15969 = FACE_OUTER_BOUND ( 'NONE', #55749, .T. ) ; +#15971 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.897353801849635915E-15, 0.000000000000000000 ) ) ; +#15972 = CARTESIAN_POINT ( 'NONE', ( 1.408334268560540004, -1.010972591757870021, 0.8299999999999998490 ) ) ; +#15973 = ORIENTED_EDGE ( 'NONE', *, *, #62220, .F. ) ; +#15974 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#15975 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15976 = FACE_OUTER_BOUND ( 'NONE', #72162, .T. ) ; +#15977 = PRESENTATION_STYLE_ASSIGNMENT (( #85440 ) ) ; +#15978 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43221 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61386, #52, #70507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#15979 = VERTEX_POINT ( 'NONE', #93661 ) ; +#15980 = ORIENTED_EDGE ( 'NONE', *, *, #43752, .F. ) ; +#15981 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#15982 = ORIENTED_EDGE ( 'NONE', *, *, #70239, .T. ) ; +#15983 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89409 ), #25876 ) ; +#15984 = EDGE_CURVE ( 'NONE', #66452, #97257, #23786, .T. ) ; +#15985 = VERTEX_POINT ( 'NONE', #58485 ) ; +#15987 = ORIENTED_EDGE ( 'NONE', *, *, #60248, .F. ) ; +#15986 = FACE_OUTER_BOUND ( 'NONE', #57105, .T. ) ; +#15988 = LINE ( 'NONE', #86471, #37681 ) ; +#15990 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15989 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#15991 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#15992 = EDGE_LOOP ( 'NONE', ( #93303, #95336, #81730, #33349 ) ) ; +#15994 = EDGE_CURVE ( 'NONE', #30000, #97744, #72756, .T. ) ; +#15993 = SURFACE_SIDE_STYLE ('',( #85456 ) ) ; +#15995 = SURFACE_SIDE_STYLE ('',( #40538 ) ) ; +#15996 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#15997 = VERTEX_POINT ( 'NONE', #65585 ) ; +#15998 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64934 ) ) ; +#15999 = LINE ( 'NONE', #47164, #2496 ) ; +#16000 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#16001 = PLANE ( 'NONE', #30087 ) ; +#16002 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.1499999999999999944, 0.08229670385730990245 ) ) ; +#16003 = ORIENTED_EDGE ( 'NONE', *, *, #78042, .F. ) ; +#16004 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53571 ), #94277 ) ; +#16006 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16005 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16007 = EDGE_LOOP ( 'NONE', ( #57845, #19274, #77727, #82612 ) ) ; +#16008 = LINE ( 'NONE', #31855, #33227 ) ; +#16009 = STYLED_ITEM ( 'NONE', ( #93401 ), #24763 ) ; +#16010 = AXIS2_PLACEMENT_3D ( 'NONE', #87169, #17197, #49900 ) ; +#16011 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14385 ), #71516 ) ; +#16012 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#16013 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16014 = ORIENTED_EDGE ( 'NONE', *, *, #46744, .T. ) ; +#16016 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90660 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100142, #24063, #78652 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16015 = FILL_AREA_STYLE_COLOUR ( '', #22139 ) ; +#16017 = ORIENTED_EDGE ( 'NONE', *, *, #99341, .T. ) ; +#16018 = FILL_AREA_STYLE_COLOUR ( '', #37297 ) ; +#16019 = CLOSED_SHELL ( 'NONE', ( #6879, #91030, #41255, #59296, #35378, #14525, #77153, #40721, #19653, #60271, #19319, #72601 ) ) ; +#16021 = SURFACE_STYLE_USAGE ( .BOTH. , #17527 ) ; +#16020 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16022 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16023 = LINE ( 'NONE', #1221, #11286 ) ; +#16024 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42171 ) ) ; +#16025 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#16026 = FILL_AREA_STYLE_COLOUR ( '', #88393 ) ; +#16027 = FILL_AREA_STYLE ('',( #32392 ) ) ; +#16028 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16029 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60126 ), #95988 ) ; +#16030 = FILL_AREA_STYLE_COLOUR ( '', #84171 ) ; +#16031 = ORIENTED_EDGE ( 'NONE', *, *, #91262, .F. ) ; +#16032 = CARTESIAN_POINT ( 'NONE', ( -1.166406359071090026, -1.149778012002649952, 0.8300000000000002931 ) ) ; +#16033 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16034 = CONICAL_SURFACE ( 'NONE', #82908, 0.6999999999948158802, 0.4636476090008060935 ) ; +#16036 = LINE ( 'NONE', #8309, #90107 ) ; +#16035 = FILL_AREA_STYLE_COLOUR ( '', #80577 ) ; +#16037 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16038 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8155, 'distance_accuracy_value', 'NONE'); +#16039 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53152 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47485, #23519, #92897 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16040 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16041 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.500000000000000222, 0.1829999999999580296 ) ) ; +#16042 = DIRECTION ( 'NONE', ( -0.9412541746845646262, 0.3376989467541748891, 0.000000000000000000 ) ) ; +#16043 = ORIENTED_EDGE ( 'NONE', *, *, #9333, .T. ) ; +#16044 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, -3.500000000000000444, 0.000000000000000000 ) ) ; +#16045 = SURFACE_STYLE_USAGE ( .BOTH. , #55417 ) ; +#16046 = FACE_OUTER_BOUND ( 'NONE', #14549, .T. ) ; +#16047 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#16048 = SURFACE_STYLE_FILL_AREA ( #62571 ) ; +#16049 = AXIS2_PLACEMENT_3D ( 'NONE', #71918, #35648, #89250 ) ; +#16050 = PRESENTATION_STYLE_ASSIGNMENT (( #39562 ) ) ; +#16051 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#16052 = SURFACE_STYLE_FILL_AREA ( #64070 ) ; +#16053 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16054 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16056 = SURFACE_STYLE_USAGE ( .BOTH. , #70187 ) ; +#16055 = AXIS2_PLACEMENT_3D ( 'NONE', #90951, #21006, #13253 ) ; +#16057 = FACE_OUTER_BOUND ( 'NONE', #39406, .T. ) ; +#16058 = PRESENTATION_STYLE_ASSIGNMENT (( #14529 ) ) ; +#16059 = CARTESIAN_POINT ( 'NONE', ( 0.4645119866146591447, 0.3274465759269657994, 0.8299999999999999600 ) ) ; +#16060 = ORIENTED_EDGE ( 'NONE', *, *, #73247, .T. ) ; +#16061 = STYLED_ITEM ( 'NONE', ( #91850 ), #56643 ) ; +#16063 = ADVANCED_FACE ( 'NONE', ( #57461 ), #57976, .T. ) ; +#16062 = SURFACE_STYLE_USAGE ( .BOTH. , #86033 ) ; +#16064 = PLANE ( 'NONE', #14477 ) ; +#16065 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, -0.09999999999999988065, 0.000000000000000000 ) ) ; +#16066 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#16067 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#16068 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16069 = CARTESIAN_POINT ( 'NONE', ( -1.016236428037849970, -1.189797473215369994, 0.8100000000000000533 ) ) ; +#16070 = ORIENTED_EDGE ( 'NONE', *, *, #63630, .T. ) ; +#16071 = MANIFOLD_SOLID_BREP ( 'ÊäÈë8', #46857 ) ; +#16072 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#16073 = AXIS2_PLACEMENT_3D ( 'NONE', #88329, #11127, #35242 ) ; +#16074 = PRESENTATION_STYLE_ASSIGNMENT (( #46197 ) ) ; +#16076 = SURFACE_SIDE_STYLE ('',( #99738 ) ) ; +#16075 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47065 ) ) ; +#16077 = ORIENTED_EDGE ( 'NONE', *, *, #90190, .T. ) ; +#16078 = EDGE_CURVE ( 'NONE', #12048, #56508, #73275, .T. ) ; +#16079 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8648700000000000276 ) ) ; +#16080 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69875 ) ) ; +#16081 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#16082 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#16083 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, 3.500000000000000444, 0.000000000000000000 ) ) ; +#16084 = ORIENTED_EDGE ( 'NONE', *, *, #20088, .F. ) ; +#16085 = PLANE ( 'NONE', #54777 ) ; +#16086 = SURFACE_STYLE_USAGE ( .BOTH. , #78404 ) ; +#16087 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12825, 'distance_accuracy_value', 'NONE'); +#16088 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16089 = STYLED_ITEM ( 'NONE', ( #71286 ), #117 ) ; +#16090 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#16091 = ORIENTED_EDGE ( 'NONE', *, *, #8115, .T. ) ; +#16092 = SURFACE_STYLE_USAGE ( .BOTH. , #77903 ) ; +#16093 = PRESENTATION_STYLE_ASSIGNMENT (( #86060 ) ) ; +#16094 = ORIENTED_EDGE ( 'NONE', *, *, #37039, .F. ) ; +#16095 = LINE ( 'NONE', #31445, #77066 ) ; +#16096 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16097 = STYLED_ITEM ( 'NONE', ( #72087 ), #50928 ) ; +#16098 = EDGE_CURVE ( 'NONE', #99432, #95720, #74768, .T. ) ; +#16099 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16100 = AXIS2_PLACEMENT_3D ( 'NONE', #95633, #64026, #49219 ) ; +#16101 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16102 = ORIENTED_EDGE ( 'NONE', *, *, #39725, .F. ) ; +#16103 = LINE ( 'NONE', #47272, #88391 ) ; +#16104 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14728, 'distance_accuracy_value', 'NONE'); +#16105 = FILL_AREA_STYLE_COLOUR ( '', #37611 ) ; +#16106 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#16107 = EDGE_CURVE ( 'NONE', #82666, #62161, #25808, .T. ) ; +#16108 = VERTEX_POINT ( 'NONE', #43112 ) ; +#16109 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16110 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#16111 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#16112 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6306 ), #27622 ) ; +#16114 = VERTEX_POINT ( 'NONE', #50321 ) ; +#16113 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16115 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16116 = ORIENTED_EDGE ( 'NONE', *, *, #13780, .T. ) ; +#16117 = ORIENTED_EDGE ( 'NONE', *, *, #32793, .F. ) ; +#16118 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#16120 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#16119 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999854491, -1.979898987322330051, 0.5799137866959191978 ) ) ; +#16121 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16122 = ORIENTED_EDGE ( 'NONE', *, *, #8708, .F. ) ; +#16123 = VECTOR ( 'NONE', #96118, 1000.000000000000000 ) ; +#16124 = MANIFOLD_SOLID_BREP ( 'ÊäÈë110', #24168 ) ; +#16125 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94418 ), #1526 ) ; +#16126 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16127 = LINE ( 'NONE', #8408, #95614 ) ; +#16128 = VERTEX_POINT ( 'NONE', #53292 ) ; +#16130 = FILL_AREA_STYLE_COLOUR ( '', #64826 ) ; +#16129 = LINE ( 'NONE', #39647, #82514 ) ; +#16131 = ORIENTED_EDGE ( 'NONE', *, *, #68268, .T. ) ; +#16133 = VERTEX_POINT ( 'NONE', #77252 ) ; +#16132 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #54020, #79400, #95174, #9362 ), + ( #41114, #18069, #76989, #22889 ), + ( #72231, #2306, #80412, #40603 ), + ( #10349, #64576, #6958, #72734 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000), + ( 0.8047378541243662697, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243662697), + ( 0.8047378541243662697, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243662697), + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#16135 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16134 = STYLED_ITEM ( 'NONE', ( #98757 ), #81138 ) ; +#16136 = SURFACE_SIDE_STYLE ('',( #32516 ) ) ; +#16137 = VECTOR ( 'NONE', #16990, 1000.000000000000000 ) ; +#16138 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#16139 = ADVANCED_FACE ( 'NONE', ( #45086 ), #80946, .T. ) ; +#16140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1394 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76384, #82568, #51934 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16141 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#16142 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32819 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43063, #73228, #20074 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16143 = LINE ( 'NONE', #7423, #99629 ) ; +#16144 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27296, #49269, #80932, #41612 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16145 = EDGE_CURVE ( 'NONE', #47158, #2945, #21635, .T. ) ; +#16146 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16147 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#16148 = ORIENTED_EDGE ( 'NONE', *, *, #76308, .F. ) ; +#16149 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16150 = SURFACE_SIDE_STYLE ('',( #23870 ) ) ; +#16151 = SURFACE_STYLE_USAGE ( .BOTH. , #7928 ) ; +#16152 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16153 = LINE ( 'NONE', #96657, #68295 ) ; +#16154 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999667, 0.1900000000000000022 ) ) ; +#16155 = VECTOR ( 'NONE', #83245, 1000.000000000000000 ) ; +#16156 = SURFACE_STYLE_USAGE ( .BOTH. , #7439 ) ; +#16157 = EDGE_CURVE ( 'NONE', #59719, #45808, #22645, .T. ) ; +#16158 = ORIENTED_EDGE ( 'NONE', *, *, #41218, .F. ) ; +#16159 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16160 = EDGE_CURVE ( 'NONE', #36327, #36035, #51796, .T. ) ; +#16161 = SURFACE_SIDE_STYLE ('',( #23880 ) ) ; +#16162 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8199999999999999512, 0.000000000000000000 ) ) ; +#16163 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16164 = FILL_AREA_STYLE_COLOUR ( '', #16830 ) ; +#16165 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16166 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16167 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67902, #12735, #58810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16168 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16169 = SURFACE_SIDE_STYLE ('',( #49365 ) ) ; +#16170 = VECTOR ( 'NONE', #57836, 1000.000000000000000 ) ; +#16171 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16172 = LINE ( 'NONE', #99844, #90756 ) ; +#16173 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 1.076179938779915135, 0.000000000000000000 ) ) ; +#16174 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16175 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16176 = VECTOR ( 'NONE', #74387, 1000.000000000000000 ) ; +#16178 = EDGE_CURVE ( 'NONE', #59891, #71553, #22130, .T. ) ; +#16177 = SURFACE_STYLE_FILL_AREA ( #93766 ) ; +#16179 = SURFACE_STYLE_FILL_AREA ( #55039 ) ; +#16180 = LINE ( 'NONE', #63213, #46874 ) ; +#16181 = FILL_AREA_STYLE_COLOUR ( '', #86177 ) ; +#16182 = ORIENTED_EDGE ( 'NONE', *, *, #20925, .F. ) ; +#16183 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.700000000000000178, 1.495481557822595733E-79 ) ) ; +#16184 = SURFACE_STYLE_USAGE ( .BOTH. , #86675 ) ; +#16185 = AXIS2_PLACEMENT_3D ( 'NONE', #27818, #27297, #91070 ) ; +#16187 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#16186 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16188 = SURFACE_STYLE_USAGE ( .BOTH. , #61207 ) ; +#16189 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24423 ) ) ; +#16190 = EDGE_CURVE ( 'NONE', #83515, #47305, #67088, .T. ) ; +#16191 = VECTOR ( 'NONE', #30827, 1000.000000000000000 ) ; +#16192 = VECTOR ( 'NONE', #86542, 1000.000000000000000 ) ; +#16193 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#16194 = ORIENTED_EDGE ( 'NONE', *, *, #27003, .T. ) ; +#16195 = SURFACE_STYLE_FILL_AREA ( #30503 ) ; +#16196 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#16197 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72275 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55242, #17394, #49084 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16198 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.383226165704513715E-178, -3.012399831378599940E-146 ) ) ; +#16199 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57575 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71620, #49151, #95560 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16200 = PRESENTATION_STYLE_ASSIGNMENT (( #62224 ) ) ; +#16201 = SURFACE_STYLE_FILL_AREA ( #54039 ) ; +#16202 = VECTOR ( 'NONE', #52806, 1000.000000000000000 ) ; +#16203 = ORIENTED_EDGE ( 'NONE', *, *, #69006, .F. ) ; +#16204 = EDGE_LOOP ( 'NONE', ( #80590, #24726, #72397, #51101 ) ) ; +#16205 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16206 = ORIENTED_EDGE ( 'NONE', *, *, #5018, .T. ) ; +#16207 = SURFACE_SIDE_STYLE ('',( #15713 ) ) ; +#16208 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16209 = SURFACE_STYLE_USAGE ( .BOTH. , #86184 ) ; +#16210 = PRODUCT_CONTEXT ( 'NONE', #6351, 'mechanical' ) ; +#16211 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000000222, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#16212 = EDGE_CURVE ( 'NONE', #72043, #34589, #79476, .T. ) ; +#16213 = SURFACE_SIDE_STYLE ('',( #93314 ) ) ; +#16214 = VECTOR ( 'NONE', #81640, 1000.000000000000114 ) ; +#16216 = ORIENTED_EDGE ( 'NONE', *, *, #47626, .F. ) ; +#16215 = ORIENTED_EDGE ( 'NONE', *, *, #28619, .T. ) ; +#16217 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45788, #6455, #76970 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16218 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#16219 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60315 ) ) ; +#16220 = ORIENTED_EDGE ( 'NONE', *, *, #14614, .F. ) ; +#16221 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16222 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23761, 'distance_accuracy_value', 'NONE'); +#16223 = LINE ( 'NONE', #94838, #63720 ) ; +#16224 = ORIENTED_EDGE ( 'NONE', *, *, #10924, .T. ) ; +#16225 = EDGE_CURVE ( 'NONE', #56861, #3964, #84421, .T. ) ; +#16226 = MANIFOLD_SOLID_BREP ( 'ÊäÈë106', #24023 ) ; +#16227 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16228 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#16229 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16230 = VECTOR ( 'NONE', #9086, 1000.000000000000000 ) ; +#16231 = EDGE_LOOP ( 'NONE', ( #23063, #66429, #96347, #17152 ) ) ; +#16232 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16233 = ORIENTED_EDGE ( 'NONE', *, *, #24573, .T. ) ; +#16234 = ORIENTED_EDGE ( 'NONE', *, *, #81853, .T. ) ; +#16235 = VECTOR ( 'NONE', #20981, 1000.000000000000000 ) ; +#16236 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16237 = FILL_AREA_STYLE_COLOUR ( '', #45538 ) ; +#16238 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16240 = VERTEX_POINT ( 'NONE', #31297 ) ; +#16239 = FACE_OUTER_BOUND ( 'NONE', #54569, .T. ) ; +#16241 = FACE_OUTER_BOUND ( 'NONE', #15754, .T. ) ; +#16243 = VECTOR ( 'NONE', #68784, 1000.000000000000000 ) ; +#16242 = LINE ( 'NONE', #85711, #59695 ) ; +#16244 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#16245 = ORIENTED_EDGE ( 'NONE', *, *, #60752, .T. ) ; +#16246 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16247 = PLANE ( 'NONE', #41276 ) ; +#16248 = ORIENTED_EDGE ( 'NONE', *, *, #71498, .T. ) ; +#16249 = EDGE_LOOP ( 'NONE', ( #45099, #96864, #10518, #23947 ) ) ; +#16251 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16250 = FACE_OUTER_BOUND ( 'NONE', #16561, .T. ) ; +#16252 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, -0.2399999999999999911 ) ) ; +#16253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16254 = ADVANCED_FACE ( 'NONE', ( #46077 ), #31810, .T. ) ; +#16255 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16256 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#16257 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90664, 'distance_accuracy_value', 'NONE'); +#16258 = LINE ( 'NONE', #23991, #50812 ) ; +#16259 = ORIENTED_EDGE ( 'NONE', *, *, #27819, .T. ) ; +#16260 = CARTESIAN_POINT ( 'NONE', ( 0.4672226176551799726, -1.085850084742399968, 0.8299999999999999600 ) ) ; +#16261 = CARTESIAN_POINT ( 'NONE', ( 0.07312563425034800113, -1.247909878090150082, 0.8100000000000000533 ) ) ; +#16262 = EDGE_LOOP ( 'NONE', ( #96154, #83689, #68626, #99190, #96746, #51314 ) ) ; +#16263 = FACE_OUTER_BOUND ( 'NONE', #12296, .T. ) ; +#16264 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56991 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3608, #90366, #82721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16265 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#16266 = AXIS2_PLACEMENT_3D ( 'NONE', #71242, #86567, #32458 ) ; +#16267 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16268 = AXIS2_PLACEMENT_3D ( 'NONE', #9806, #34411, #26743 ) ; +#16269 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16270 = VECTOR ( 'NONE', #99982, 1000.000000000000000 ) ; +#16271 = FILL_AREA_STYLE ('',( #39275 ) ) ; +#16272 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5199999999376814230, -0.6999999999379724613 ) ) ; +#16273 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16274 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8199999999999999512 ) ) ; +#16275 = EDGE_CURVE ( 'NONE', #92365, #87853, #47637, .T. ) ; +#16276 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62687 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92340, #35389, #34874 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16277 = ADVANCED_FACE ( 'NONE', ( #94047 ), #16973, .T. ) ; +#16278 = PLANE ( 'NONE', #48859 ) ; +#16279 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16280 = SURFACE_STYLE_USAGE ( .BOTH. , #1515 ) ; +#16281 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73404 ), #37542 ) ; +#16282 = LINE ( 'NONE', #51747, #7547 ) ; +#16283 = CYLINDRICAL_SURFACE ( 'NONE', #66876, 0.05000000000000012768 ) ; +#16284 = LINE ( 'NONE', #69918, #87457 ) ; +#16285 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92872 ) ) ; +#16286 = LINE ( 'NONE', #55661, #56765 ) ; +#16287 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16288 = FILL_AREA_STYLE ('',( #45336 ) ) ; +#16289 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26666 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11031, #73426, #30419 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16290 = STYLED_ITEM ( 'NONE', ( #10326 ), #42836 ) ; +#16291 = MANIFOLD_SOLID_BREP ( 'ÊäÈë25', #15805 ) ; +#16292 = EDGE_CURVE ( 'NONE', #76650, #100648, #51177, .T. ) ; +#16293 = EDGE_LOOP ( 'NONE', ( #16245, #63822, #17653, #62936 ) ) ; +#16294 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16295 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79522, 'distance_accuracy_value', 'NONE'); +#16296 = VERTEX_POINT ( 'NONE', #9249 ) ; +#16298 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79394, 'distance_accuracy_value', 'NONE'); +#16297 = SURFACE_STYLE_FILL_AREA ( #79139 ) ; +#16299 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.4999999999999993339, 5.608055841774961276E-79 ) ) ; +#16300 = EDGE_CURVE ( 'NONE', #54031, #21935, #194, .T. ) ; +#16301 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16302 = STYLED_ITEM ( 'NONE', ( #24962 ), #10822 ) ; +#16303 = SURFACE_STYLE_USAGE ( .BOTH. , #93894 ) ; +#16304 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16305 = LINE ( 'NONE', #8578, #83450 ) ; +#16306 = VECTOR ( 'NONE', #12996, 1000.000000000000000 ) ; +#16307 = ADVANCED_FACE ( 'NONE', ( #73144 ), #26185, .T. ) ; +#16308 = ORIENTED_EDGE ( 'NONE', *, *, #83435, .F. ) ; +#16309 = ADVANCED_FACE ( 'NONE', ( #65458 ), #57856, .T. ) ; +#16310 = ORIENTED_EDGE ( 'NONE', *, *, #43665, .T. ) ; +#16311 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72241, 'distance_accuracy_value', 'NONE'); +#16312 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #123, 'distance_accuracy_value', 'NONE'); +#16313 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94932 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64849, #11633, #88834 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16314 = EDGE_CURVE ( 'NONE', #25602, #25247, #76630, .T. ) ; +#16315 = FACE_OUTER_BOUND ( 'NONE', #78846, .T. ) ; +#16316 = SURFACE_SIDE_STYLE ('',( #15822 ) ) ; +#16317 = ORIENTED_EDGE ( 'NONE', *, *, #92687, .F. ) ; +#16318 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #44934 ) ) ; +#16319 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#16320 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16321 = VERTEX_POINT ( 'NONE', #82804 ) ; +#16322 = SURFACE_STYLE_FILL_AREA ( #70990 ) ; +#16323 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16324 = EDGE_LOOP ( 'NONE', ( #40815, #2302, #8386, #30728 ) ) ; +#16325 = LINE ( 'NONE', #8610, #51849 ) ; +#16326 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#16327 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16328 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3648 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76418, #68244, #20287 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16329 = LINE ( 'NONE', #85297, #78870 ) ; +#16330 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52257 ) ) ; +#16331 = DIRECTION ( 'NONE', ( -1.425188158846549879E-32, 1.000000000000000000, -3.659014888116197608E-48 ) ) ; +#16332 = EDGE_CURVE ( 'NONE', #30846, #74099, #59368, .T. ) ; +#16333 = FACE_OUTER_BOUND ( 'NONE', #23242, .T. ) ; +#16334 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#16336 = ORIENTED_EDGE ( 'NONE', *, *, #71959, .T. ) ; +#16335 = ORIENTED_EDGE ( 'NONE', *, *, #61535, .F. ) ; +#16337 = SURFACE_STYLE_FILL_AREA ( #86321 ) ; +#16338 = ORIENTED_EDGE ( 'NONE', *, *, #44416, .F. ) ; +#16339 = FILL_AREA_STYLE ('',( #32727 ) ) ; +#16340 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4912 ) ) ; +#16341 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16342 = SURFACE_STYLE_FILL_AREA ( #86842 ) ; +#16343 = VERTEX_POINT ( 'NONE', #76137 ) ; +#16344 = EDGE_CURVE ( 'NONE', #51382, #6687, #45453, .T. ) ; +#16345 = ORIENTED_EDGE ( 'NONE', *, *, #39599, .T. ) ; +#16346 = AXIS2_PLACEMENT_3D ( 'NONE', #84565, #67729, #22284 ) ; +#16347 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.000000000000000000 ) ) ; +#16348 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16349 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#16351 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16350 = SURFACE_SIDE_STYLE ('',( #55227 ) ) ; +#16352 = ORIENTED_EDGE ( 'NONE', *, *, #91835, .T. ) ; +#16353 = EDGE_CURVE ( 'NONE', #59518, #28925, #98528, .T. ) ; +#16354 = ORIENTED_EDGE ( 'NONE', *, *, #58655, .F. ) ; +#16355 = PLANE ( 'NONE', #19277 ) ; +#16356 = EDGE_LOOP ( 'NONE', ( #57785, #30458, #5557, #76230 ) ) ; +#16357 = FILL_AREA_STYLE_COLOUR ( '', #1995 ) ; +#16358 = STYLED_ITEM ( 'NONE', ( #22716 ), #64617 ) ; +#16359 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97904 ) ) ; +#16360 = EDGE_CURVE ( 'NONE', #67140, #98291, #53174, .T. ) ; +#16362 = VERTEX_POINT ( 'NONE', #68943 ) ; +#16361 = FILL_AREA_STYLE ('',( #100038 ) ) ; +#16363 = SURFACE_STYLE_FILL_AREA ( #8643 ) ; +#16364 = SURFACE_STYLE_FILL_AREA ( #48582 ) ; +#16365 = CARTESIAN_POINT ( 'NONE', ( 1.775025884298160106, -1.496872818153279994, 0.8099999999999996092 ) ) ; +#16366 = ORIENTED_EDGE ( 'NONE', *, *, #37130, .F. ) ; +#16367 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#16368 = ORIENTED_EDGE ( 'NONE', *, *, #54382, .T. ) ; +#16369 = AXIS2_PLACEMENT_3D ( 'NONE', #47225, #48765, #39568 ) ; +#16370 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16372 = ORIENTED_EDGE ( 'NONE', *, *, #86763, .T. ) ; +#16371 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 4.008477000000000068, 0.8648700000000000276 ) ) ; +#16374 = ADVANCED_FACE ( 'NONE', ( #37363 ), #20505, .T. ) ; +#16373 = AXIS2_PLACEMENT_3D ( 'NONE', #45500, #23582, #14854 ) ; +#16375 = FILL_AREA_STYLE_COLOUR ( '', #11565 ) ; +#16377 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#16376 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#16378 = LINE ( 'NONE', #10680, #18092 ) ; +#16379 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#16380 = VERTEX_POINT ( 'NONE', #5648 ) ; +#16381 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97923 ) ) ; +#16382 = FILL_AREA_STYLE_COLOUR ( '', #12530 ) ; +#16383 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16384 = CARTESIAN_POINT ( 'NONE', ( -0.3116078311044310212, -1.336216925617480067, 0.8100000000000000533 ) ) ; +#16385 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16386 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16387 = FILL_AREA_STYLE_COLOUR ( '', #73109 ) ; +#16388 = CARTESIAN_POINT ( 'NONE', ( -1.383333333333333526, -3.099999999999989875, 0.000000000000000000 ) ) ; +#16389 = PLANE ( 'NONE', #1020 ) ; +#16390 = MANIFOLD_SOLID_BREP ( 'ÊäÈë56', #71449 ) ; +#16391 = ADVANCED_FACE ( 'NONE', ( #85803 ), #8883, .F. ) ; +#16392 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50728 ) ) ; +#16393 = STYLED_ITEM ( 'NONE', ( #6729 ), #33741 ) ; +#16394 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 2.827608999999999817, 0.8648700000000000276 ) ) ; +#16395 = VERTEX_POINT ( 'NONE', #86309 ) ; +#16396 = EDGE_CURVE ( 'NONE', #5131, #69898, #16325, .T. ) ; +#16397 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16398 = SURFACE_STYLE_USAGE ( .BOTH. , #54248 ) ; +#16399 = VECTOR ( 'NONE', #32879, 1000.000000000000000 ) ; +#16400 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92989 ), #84736 ) ; +#16401 = ORIENTED_EDGE ( 'NONE', *, *, #58888, .F. ) ; +#16402 = AXIS2_PLACEMENT_3D ( 'NONE', #43321, #35693, #65816 ) ; +#16403 = SURFACE_SIDE_STYLE ('',( #9208 ) ) ; +#16404 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16405 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85570 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49326, #3856, #10934 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16406 = SURFACE_SIDE_STYLE ('',( #23606 ) ) ; +#16407 = ORIENTED_EDGE ( 'NONE', *, *, #29523, .F. ) ; +#16408 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#16409 = FACE_OUTER_BOUND ( 'NONE', #69306, .T. ) ; +#16410 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998730, -0.1400000000000000688 ) ) ; +#16411 = CARTESIAN_POINT ( 'NONE', ( 1.071224486614660520, 1.221896575926969986, 0.8100000000000000533 ) ) ; +#16412 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16413 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#16414 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16415 = VECTOR ( 'NONE', #87539, 999.9999999999998863 ) ; +#16416 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.000000000000000000 ) ) ; +#16417 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16418 = SURFACE_SIDE_STYLE ('',( #12866 ) ) ; +#16419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16420 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19005, 'distance_accuracy_value', 'NONE'); +#16421 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16422 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16423 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16424 = VECTOR ( 'NONE', #73903, 1000.000000000000000 ) ; +#16425 = VERTEX_POINT ( 'NONE', #1567 ) ; +#16426 = EDGE_CURVE ( 'NONE', #86944, #32170, #14800, .T. ) ; +#16427 = ORIENTED_EDGE ( 'NONE', *, *, #12779, .T. ) ; +#16428 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16430 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7750, 'distance_accuracy_value', 'NONE'); +#16429 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16431 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16536, 'distance_accuracy_value', 'NONE'); +#16432 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16433 = SURFACE_STYLE_FILL_AREA ( #55316 ) ; +#16434 = SURFACE_STYLE_FILL_AREA ( #31791 ) ; +#16435 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16436 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#16437 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, -0.8000000000000001554 ) ) ; +#16438 = EDGE_LOOP ( 'NONE', ( #97859, #83397, #62094, #34528, #13942, #86727 ) ) ; +#16439 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#16440 = LINE ( 'NONE', #47628, #49906 ) ; +#16441 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34300, 'distance_accuracy_value', 'NONE'); +#16442 = ORIENTED_EDGE ( 'NONE', *, *, #22186, .F. ) ; +#16443 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#16444 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#16445 = VERTEX_POINT ( 'NONE', #32711 ) ; +#16446 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93109 ), #21365 ) ; +#16447 = STYLED_ITEM ( 'NONE', ( #64982 ), #10348 ) ; +#16448 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16449 = LINE ( 'NONE', #41012, #3804 ) ; +#16450 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16451 = PLANE ( 'NONE', #32771 ) ; +#16452 = EDGE_CURVE ( 'NONE', #14732, #73645, #11634, .T. ) ; +#16453 = FACE_OUTER_BOUND ( 'NONE', #4324, .T. ) ; +#16454 = ORIENTED_EDGE ( 'NONE', *, *, #20050, .T. ) ; +#16455 = MANIFOLD_SOLID_BREP ( 'ÊäÈë42', #37059 ) ; +#16456 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16457 = FILL_AREA_STYLE ('',( #64486 ) ) ; +#16458 = EDGE_CURVE ( 'NONE', #91073, #81132, #95960, .T. ) ; +#16459 = ORIENTED_EDGE ( 'NONE', *, *, #79589, .F. ) ; +#16460 = PLANE ( 'NONE', #8855 ) ; +#16461 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44188 ) ) ; +#16462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3478 ), #99570 ) ; +#16463 = FILL_AREA_STYLE ('',( #55830 ) ) ; +#16464 = SURFACE_STYLE_FILL_AREA ( #86459 ) ; +#16465 = FACE_OUTER_BOUND ( 'NONE', #17501, .T. ) ; +#16466 = ORIENTED_EDGE ( 'NONE', *, *, #44498, .F. ) ; +#16467 = VERTEX_POINT ( 'NONE', #65339 ) ; +#16468 = SURFACE_STYLE_FILL_AREA ( #47659 ) ; +#16469 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0402_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0402_20210301.STEP', '', ( #41271 ) ) ; +#16470 = ORIENTED_EDGE ( 'NONE', *, *, #6210, .T. ) ; +#16471 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49115 ), #6662 ) ; +#16472 = SURFACE_STYLE_FILL_AREA ( #1727 ) ; +#16473 = VECTOR ( 'NONE', #1258, 1000.000000000000000 ) ; +#16474 = ADVANCED_FACE ( 'NONE', ( #33724 ), #66362, .T. ) ; +#16475 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16476 = ORIENTED_EDGE ( 'NONE', *, *, #5117, .F. ) ; +#16478 = ORIENTED_EDGE ( 'NONE', *, *, #25046, .T. ) ; +#16477 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#16479 = STYLED_ITEM ( 'NONE', ( #19179 ), #8281 ) ; +#16480 = STYLED_ITEM ( 'NONE', ( #2144 ), #94894 ) ; +#16481 = SURFACE_STYLE_FILL_AREA ( #46639 ) ; +#16482 = FACE_OUTER_BOUND ( 'NONE', #32331, .T. ) ; +#16483 = SURFACE_SIDE_STYLE ('',( #79837 ) ) ; +#16484 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16485 = ORIENTED_EDGE ( 'NONE', *, *, #28552, .F. ) ; +#16487 = EDGE_CURVE ( 'NONE', #43154, #71662, #34739, .T. ) ; +#16486 = FILL_AREA_STYLE ('',( #78806 ) ) ; +#16488 = CARTESIAN_POINT ( 'NONE', ( 1.813028831487849990, -1.379727385542079965, 0.8099999999999997202 ) ) ; +#16489 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8648700000000000276 ) ) ; +#16490 = ORIENTED_EDGE ( 'NONE', *, *, #42684, .F. ) ; +#16491 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17687 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58515, #44137, #67115 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16492 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16493 = SURFACE_STYLE_FILL_AREA ( #4878 ) ; +#16494 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#16495 = ORIENTED_EDGE ( 'NONE', *, *, #58244, .T. ) ; +#16496 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88269 ), #21411 ) ; +#16497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50825 ) ) ; +#16499 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000001110, -3.383333333333326642, 0.000000000000000000 ) ) ; +#16498 = PRESENTATION_STYLE_ASSIGNMENT (( #198 ) ) ; +#16500 = VERTEX_POINT ( 'NONE', #56719 ) ; +#16501 = EDGE_CURVE ( 'NONE', #94608, #11727, #10623, .T. ) ; +#16502 = EDGE_CURVE ( 'NONE', #71612, #16858, #96964, .T. ) ; +#16503 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16504 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16505 = SURFACE_STYLE_USAGE ( .BOTH. , #31858 ) ; +#16506 = EDGE_CURVE ( 'NONE', #87221, #28324, #9630, .T. ) ; +#16507 = PLANE ( 'NONE', #77688 ) ; +#16508 = EDGE_CURVE ( 'NONE', #52699, #4927, #67830, .T. ) ; +#16509 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51224, #58405, #82363, #26740 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16510 = PRESENTATION_STYLE_ASSIGNMENT (( #45794 ) ) ; +#16511 = ORIENTED_EDGE ( 'NONE', *, *, #81020, .F. ) ; +#16513 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#16512 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16514 = CARTESIAN_POINT ( 'NONE', ( -0.7175359621965019530, 1.464383040805290026, 0.8100000000000000533 ) ) ; +#16515 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#16516 = EDGE_CURVE ( 'NONE', #74215, #80224, #37727, .T. ) ; +#16517 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16807, 'distance_accuracy_value', 'NONE'); +#16518 = AXIS2_PLACEMENT_3D ( 'NONE', #39066, #1262, #8838 ) ; +#16519 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16520 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16521 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#16522 = VECTOR ( 'NONE', #74416, 1000.000000000000000 ) ; +#16523 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#16524 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16525 = EDGE_CURVE ( 'NONE', #80677, #26141, #97467, .T. ) ; +#16526 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16527 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#16528 = ORIENTED_EDGE ( 'NONE', *, *, #75905, .F. ) ; +#16529 = FILL_AREA_STYLE ('',( #77320 ) ) ; +#16530 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#16533 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16532 = FILL_AREA_STYLE ('',( #3262 ) ) ; +#16531 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#16534 = AXIS2_PLACEMENT_3D ( 'NONE', #6261, #5779, #28798 ) ; +#16535 = FACE_OUTER_BOUND ( 'NONE', #85270, .T. ) ; +#16536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16537 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#16538 = SURFACE_STYLE_FILL_AREA ( #32907 ) ; +#16539 = SURFACE_STYLE_USAGE ( .BOTH. , #57937 ) ; +#16540 = VERTEX_POINT ( 'NONE', #99404 ) ; +#16541 = FACE_OUTER_BOUND ( 'NONE', #29461, .T. ) ; +#16542 = CARTESIAN_POINT ( 'NONE', ( 3.100999124875012392, 7.282381875124987580, 0.8648700000000000276 ) ) ; +#16543 = PRESENTATION_STYLE_ASSIGNMENT (( #8323 ) ) ; +#16544 = AXIS2_PLACEMENT_3D ( 'NONE', #82749, #43931, #20445 ) ; +#16545 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49246 ) ) ; +#16546 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16547 = LINE ( 'NONE', #55419, #821 ) ; +#16548 = SURFACE_STYLE_FILL_AREA ( #54912 ) ; +#16549 = SURFACE_STYLE_USAGE ( .BOTH. , #752 ) ; +#16550 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60629 ), #23082 ) ; +#16551 = PRESENTATION_STYLE_ASSIGNMENT (( #55920 ) ) ; +#16552 = AXIS2_PLACEMENT_3D ( 'NONE', #89799, #97433, #90296 ) ; +#16553 = LINE ( 'NONE', #72224, #42011 ) ; +#16554 = SURFACE_STYLE_FILL_AREA ( #40081 ) ; +#16555 = FILL_AREA_STYLE ('',( #69684 ) ) ; +#16556 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#16557 = VERTEX_POINT ( 'NONE', #75037 ) ; +#16558 = FILL_AREA_STYLE ('',( #55434 ) ) ; +#16559 = EDGE_CURVE ( 'NONE', #31068, #74029, #27572, .T. ) ; +#16561 = EDGE_LOOP ( 'NONE', ( #62404, #99440, #37326, #527 ) ) ; +#16560 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98072 ) ) ; +#16562 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4805, 'distance_accuracy_value', 'NONE'); +#16563 = AXIS2_PLACEMENT_3D ( 'NONE', #66425, #51124, #57805 ) ; +#16564 = DIRECTION ( 'NONE', ( 4.344024262657780003E-34, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16565 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333320425, -1.500000000000000000, 1.747825839084689943E-76 ) ) ; +#16566 = FACE_OUTER_BOUND ( 'NONE', #76029, .T. ) ; +#16567 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16568 = EDGE_CURVE ( 'NONE', #97015, #78529, #61287, .T. ) ; +#16569 = CARTESIAN_POINT ( 'NONE', ( -1.284837223313930021, -1.093211113524890088, 0.8299999999999999600 ) ) ; +#16570 = VERTEX_POINT ( 'NONE', #84186 ) ; +#16571 = STYLED_ITEM ( 'NONE', ( #27734 ), #7559 ) ; +#16572 = MANIFOLD_SOLID_BREP ( 'ÊäÈë55', #89243 ) ; +#16573 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31487, 'distance_accuracy_value', 'NONE'); +#16575 = PLANE ( 'NONE', #90150 ) ; +#16576 = ORIENTED_EDGE ( 'NONE', *, *, #67812, .F. ) ; +#16577 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#16578 = STYLED_ITEM ( 'NONE', ( #19616 ), #25383 ) ; +#16579 = CARTESIAN_POINT ( 'NONE', ( 0.5833333333333340365, 3.099999999999980549, 0.000000000000000000 ) ) ; +#16580 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16581 = EDGE_CURVE ( 'NONE', #4688, #2565, #59752, .T. ) ; +#16582 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16583 = ORIENTED_EDGE ( 'NONE', *, *, #83411, .F. ) ; +#16584 = FILL_AREA_STYLE ('',( #87576 ) ) ; +#16585 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23831, 'distance_accuracy_value', 'NONE'); +#16586 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#16587 = SURFACE_SIDE_STYLE ('',( #76895 ) ) ; +#16588 = ADVANCED_FACE ( 'NONE', ( #52060 ), #21387, .T. ) ; +#16589 = VERTEX_POINT ( 'NONE', #47896 ) ; +#16590 = SURFACE_SIDE_STYLE ('',( #87087 ) ) ; +#16591 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#16592 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#16593 = VERTEX_POINT ( 'NONE', #15184 ) ; +#16594 = LINE ( 'NONE', #41138, #38009 ) ; +#16595 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#16596 = PRESENTATION_STYLE_ASSIGNMENT (( #86579 ) ) ; +#16597 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.05000000000000000971, 0.1900000000000000022 ) ) ; +#16598 = VECTOR ( 'NONE', #62893, 1000.000000000000000 ) ; +#16599 = ORIENTED_EDGE ( 'NONE', *, *, #33184, .T. ) ; +#16600 = PLANE ( 'NONE', #41108 ) ; +#16601 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#16603 = SURFACE_STYLE_USAGE ( .BOTH. , #87103 ) ; +#16602 = SURFACE_SIDE_STYLE ('',( #87102 ) ) ; +#16604 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16605 = PRESENTATION_STYLE_ASSIGNMENT (( #78928 ) ) ; +#16606 = VERTEX_POINT ( 'NONE', #46353 ) ; +#16607 = FILL_AREA_STYLE_COLOUR ( '', #18951 ) ; +#16608 = PLANE ( 'NONE', #76739 ) ; +#16609 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18979, #17958, #27689, #72608 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16610 = FILL_AREA_STYLE_COLOUR ( '', #10381 ) ; +#16611 = STYLED_ITEM ( 'NONE', ( #7802 ), #18602 ) ; +#16612 = VECTOR ( 'NONE', #49417, 1000.000000000000000 ) ; +#16613 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16614 = ORIENTED_EDGE ( 'NONE', *, *, #86397, .F. ) ; +#16616 = PRESENTATION_STYLE_ASSIGNMENT (( #40657 ) ) ; +#16615 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#16617 = ORIENTED_EDGE ( 'NONE', *, *, #11132, .F. ) ; +#16618 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60990 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26476, #4466, #73934 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16619 = EDGE_LOOP ( 'NONE', ( #19109, #30533, #9817, #52695 ) ) ; +#16620 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16621 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41102 ), #98070 ) ; +#16622 = CARTESIAN_POINT ( 'NONE', ( 7.661837875124987818, 2.155857124875012243, 0.8991599999999999593 ) ) ; +#16623 = FILL_AREA_STYLE_COLOUR ( '', #1665 ) ; +#16624 = LINE ( 'NONE', #23323, #88105 ) ; +#16625 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37879 ) ) ; +#16626 = ORIENTED_EDGE ( 'NONE', *, *, #69324, .T. ) ; +#16627 = VECTOR ( 'NONE', #36687, 1000.000000000000000 ) ; +#16628 = ADVANCED_FACE ( 'NONE', ( #53551 ), #68826, .T. ) ; +#16629 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#16630 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 15.15000000000000036, 0.000000000000000000 ) ) ; +#16631 = SURFACE_STYLE_FILL_AREA ( #32999 ) ; +#16632 = ORIENTED_EDGE ( 'NONE', *, *, #72012, .T. ) ; +#16633 = SURFACE_SIDE_STYLE ('',( #15624 ) ) ; +#16634 = ORIENTED_EDGE ( 'NONE', *, *, #27384, .F. ) ; +#16635 = ORIENTED_EDGE ( 'NONE', *, *, #88704, .T. ) ; +#16636 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.123820061220085265, 0.000000000000000000 ) ) ; +#16637 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16638 = EDGE_CURVE ( 'NONE', #31464, #27981, #100377, .T. ) ; +#16639 = LINE ( 'NONE', #25872, #23434 ) ; +#16640 = ADVANCED_FACE ( 'NONE', ( #22389 ), #6982, .T. ) ; +#16641 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16642 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41191 ) ) ; +#16643 = ORIENTED_EDGE ( 'NONE', *, *, #94415, .F. ) ; +#16644 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#16645 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94931 ) ) ; +#16646 = FACE_OUTER_BOUND ( 'NONE', #89976, .T. ) ; +#16647 = CARTESIAN_POINT ( 'NONE', ( -0.9126575682084471230, -1.368586375555269852, 0.8099999999997166134 ) ) ; +#16648 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -7.346839692639300209E-32 ) ) ; +#16649 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16650 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54234 ) ) ; +#16652 = FILL_AREA_STYLE ('',( #49877 ) ) ; +#16653 = VERTEX_POINT ( 'NONE', #86181 ) ; +#16654 = SURFACE_STYLE_USAGE ( .BOTH. , #70306 ) ; +#16655 = PRESENTATION_STYLE_ASSIGNMENT (( #32546 ) ) ; +#16656 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.2999999999999999334, 0.5799137866959191978 ) ) ; +#16657 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.4300000000264844191, 0.6499230724029858575 ) ) ; +#16658 = SURFACE_SIDE_STYLE ('',( #40714 ) ) ; +#16659 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6764 ) ) ; +#16660 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81349, 'distance_accuracy_value', 'NONE'); +#16661 = SURFACE_SIDE_STYLE ('',( #100336 ) ) ; +#16662 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16663 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#16664 = LINE ( 'NONE', #24403, #36979 ) ; +#16665 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16666 = FACE_OUTER_BOUND ( 'NONE', #39142, .T. ) ; +#16667 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70484 ) ) ; +#16668 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16669 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#16670 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16671 = SURFACE_STYLE_FILL_AREA ( #48402 ) ; +#16672 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65618 ) ) ; +#16673 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 2.300000000000000266, -0.02000000000000000042 ) ) ; +#16674 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01085786437626903508, -0.2500000000000000000 ) ) ; +#16675 = VERTEX_POINT ( 'NONE', #47388 ) ; +#16676 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16677 = LINE ( 'NONE', #40733, #54243 ) ; +#16678 = AXIS2_PLACEMENT_3D ( 'NONE', #28259, #67047, #20575 ) ; +#16679 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41158, 'distance_accuracy_value', 'NONE'); +#16680 = VECTOR ( 'NONE', #26209, 1000.000000000000000 ) ; +#16682 = FILL_AREA_STYLE_COLOUR ( '', #69808 ) ; +#16681 = LINE ( 'NONE', #47876, #18252 ) ; +#16683 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#16684 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99762 ) ) ; +#16685 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31716, #63406, #77673, #39884 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16686 = STYLED_ITEM ( 'NONE', ( #18432 ), #87415 ) ; +#16687 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5246 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80290, #71619, #78754 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16688 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16689 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16690 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.09999999999999853451, 0.8299999999999999600 ) ) ; +#16691 = EDGE_LOOP ( 'NONE', ( #30513, #64508, #47754, #94377 ) ) ; +#16692 = LINE ( 'NONE', #56586, #20335 ) ; +#16693 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59207 ) ) ; +#16694 = FACE_OUTER_BOUND ( 'NONE', #93577, .T. ) ; +#16695 = SURFACE_SIDE_STYLE ('',( #85673 ) ) ; +#16696 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14921, 'distance_accuracy_value', 'NONE'); +#16697 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#16698 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83617, 'distance_accuracy_value', 'NONE'); +#16699 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16700 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16701 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55826 ), #68818 ) ; +#16702 = EDGE_CURVE ( 'NONE', #16845, #27262, #78521, .T. ) ; +#16703 = ORIENTED_EDGE ( 'NONE', *, *, #13021, .T. ) ; +#16704 = ORIENTED_EDGE ( 'NONE', *, *, #48966, .T. ) ; +#16705 = LINE ( 'NONE', #100373, #11125 ) ; +#16706 = STYLED_ITEM ( 'NONE', ( #75877 ), #67039 ) ; +#16707 = EDGE_LOOP ( 'NONE', ( #59550, #21338, #32439, #66408 ) ) ; +#16708 = FILL_AREA_STYLE_COLOUR ( '', #28180 ) ; +#16709 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#16710 = ADVANCED_FACE ( 'NONE', ( #8493 ), #70880, .T. ) ; +#16711 = FILL_AREA_STYLE_COLOUR ( '', #11000 ) ; +#16712 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#16713 = SURFACE_STYLE_FILL_AREA ( #32081 ) ; +#16714 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16715 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #45572, #61331 ) ; +#16716 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#16717 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16719 = ORIENTED_EDGE ( 'NONE', *, *, #89798, .F. ) ; +#16718 = ORIENTED_EDGE ( 'NONE', *, *, #33824, .F. ) ; +#16720 = AXIS2_PLACEMENT_3D ( 'NONE', #58153, #19296, #42794 ) ; +#16721 = ORIENTED_EDGE ( 'NONE', *, *, #34113, .F. ) ; +#16722 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16723 = CARTESIAN_POINT ( 'NONE', ( 1.775025884298160106, -1.496872818153279994, 0.8100000000000000533 ) ) ; +#16725 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#16724 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16726 = EDGE_LOOP ( 'NONE', ( #53150, #70908, #67439, #41532 ) ) ; +#16727 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67332 ), #90142 ) ; +#16728 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #16410, #39421, #39939, #63459 ), + ( #86402, #31261, #54261, #15413 ), + ( #8697, #23613, #69543, #7690 ), + ( #47600, #47086, #61435, #23121 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243653816, 0.8047378541243653816, 1.000000000000000000), + ( 0.8047378541243652705, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243652705), + ( 0.8047378541243652705, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243652705), + ( 1.000000000000000000, 0.8047378541243653816, 0.8047378541243653816, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#16729 = EDGE_CURVE ( 'NONE', #5810, #71812, #40250, .T. ) ; +#16730 = BREP_WITH_VOIDS ( 'NONE', #95831, ( #90137 ) ); +#16731 = PRESENTATION_STYLE_ASSIGNMENT (( #86716 ) ) ; +#16732 = PLANE ( 'NONE', #71805 ) ; +#16733 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98250 ), #88499 ) ; +#16734 = ORIENTED_EDGE ( 'NONE', *, *, #63798, .F. ) ; +#16736 = LINE ( 'NONE', #22937, #82552 ) ; +#16735 = PRESENTATION_STYLE_ASSIGNMENT (( #61255 ) ) ; +#16737 = VERTEX_POINT ( 'NONE', #87206 ) ; +#16738 = VECTOR ( 'NONE', #79975, 1000.000000000000000 ) ; +#16739 = ORIENTED_EDGE ( 'NONE', *, *, #96401, .T. ) ; +#16740 = ORIENTED_EDGE ( 'NONE', *, *, #67757, .F. ) ; +#16741 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#16742 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16743 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16744 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52649 ) ) ; +#16745 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#16747 = ORIENTED_EDGE ( 'NONE', *, *, #86929, .T. ) ; +#16746 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#16748 = EDGE_CURVE ( 'NONE', #71596, #35425, #34530, .T. ) ; +#16749 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#16750 = SURFACE_STYLE_FILL_AREA ( #55623 ) ; +#16751 = SURFACE_STYLE_USAGE ( .BOTH. , #86737 ) ; +#16752 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26796 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6092, #90419, #77106 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16753 = VERTEX_POINT ( 'NONE', #26441 ) ; +#16755 = SURFACE_STYLE_USAGE ( .BOTH. , #85207 ) ; +#16754 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#16756 = ORIENTED_EDGE ( 'NONE', *, *, #11884, .T. ) ; +#16757 = ORIENTED_EDGE ( 'NONE', *, *, #64055, .F. ) ; +#16759 = CARTESIAN_POINT ( 'NONE', ( 1.429289321881344943, 0.7100000000000000755, 0.9636038969321070180 ) ) ; +#16758 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#16760 = CARTESIAN_POINT ( 'NONE', ( 1.775366595766979971, -1.422222704560690110, 0.8300000000000002931 ) ) ; +#16761 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#16762 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38114, #84067, #68707 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16763 = AXIS2_PLACEMENT_3D ( 'NONE', #53736, #91036, #7683 ) ; +#16764 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16765 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16766 = PRESENTATION_STYLE_ASSIGNMENT (( #70401 ) ) ; +#16767 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.300000000000000044, 1.048695503451051965E-76 ) ) ; +#16768 = ADVANCED_FACE ( 'NONE', ( #50452 ), #19250, .T. ) ; +#16769 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16770 = ORIENTED_EDGE ( 'NONE', *, *, #93525, .F. ) ; +#16771 = LINE ( 'NONE', #69110, #50745 ) ; +#16772 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#16773 = ORIENTED_EDGE ( 'NONE', *, *, #33364, .F. ) ; +#16774 = CIRCLE ( 'NONE', #83725, 0.2500000000000001110 ) ; +#16775 = PLANE ( 'NONE', #26047 ) ; +#16776 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#16777 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#16778 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#16779 = PRESENTATION_STYLE_ASSIGNMENT (( #94891 ) ) ; +#16780 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16781 = FILL_AREA_STYLE_COLOUR ( '', #19472 ) ; +#16782 = LINE ( 'NONE', #79128, #31519 ) ; +#16783 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#16784 = CARTESIAN_POINT ( 'NONE', ( -1.167182179144840237, -0.9547617453595670378, 0.8299999999999998490 ) ) ; +#16785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60869 ) ) ; +#16786 = FACE_OUTER_BOUND ( 'NONE', #61334, .T. ) ; +#16787 = LINE ( 'NONE', #8059, #27028 ) ; +#16788 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16789 = EDGE_CURVE ( 'NONE', #53318, #19060, #82079, .T. ) ; +#16790 = FILL_AREA_STYLE_COLOUR ( '', #21153 ) ; +#16791 = PLANE ( 'NONE', #64890 ) ; +#16792 = FACE_OUTER_BOUND ( 'NONE', #20481, .T. ) ; +#16793 = STYLED_ITEM ( 'NONE', ( #6733 ), #53214 ) ; +#16794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43875, 'distance_accuracy_value', 'NONE'); +#16795 = ORIENTED_EDGE ( 'NONE', *, *, #30697, .F. ) ; +#16796 = DIRECTION ( 'NONE', ( -0.3438200982495999147, 0.000000000000000000, 0.9390355371548169128 ) ) ; +#16798 = EDGE_CURVE ( 'NONE', #85984, #95195, #5900, .T. ) ; +#16797 = SURFACE_STYLE_USAGE ( .BOTH. , #86790 ) ; +#16799 = ORIENTED_EDGE ( 'NONE', *, *, #20423, .F. ) ; +#16800 = SURFACE_SIDE_STYLE ('',( #16297 ) ) ; +#16801 = PLANE ( 'NONE', #46390 ) ; +#16802 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16803 = SURFACE_SIDE_STYLE ('',( #93893 ) ) ; +#16804 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36977 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5338, #45641, #38036 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16805 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42473, #34824, #42951, #97557 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16806 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999578 ) ) ; +#16807 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16808 = STYLED_ITEM ( 'NONE', ( #29526 ), #47452 ) ; +#16809 = AXIS2_PLACEMENT_3D ( 'NONE', #74394, #38472, #27428 ) ; +#16810 = ORIENTED_EDGE ( 'NONE', *, *, #79564, .T. ) ; +#16811 = ORIENTED_EDGE ( 'NONE', *, *, #11477, .F. ) ; +#16812 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#16813 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16814 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16815 = CARTESIAN_POINT ( 'NONE', ( -0.1450079136436681071, -1.164927051866627927, 0.8100000000000000533 ) ) ; +#16816 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 4.524664999999999715, 0.8991599999999999593 ) ) ; +#16817 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#16818 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92844 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76841, #62562, #29862 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16819 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#16820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16821 = FACE_OUTER_BOUND ( 'NONE', #41163, .T. ) ; +#16822 = ORIENTED_EDGE ( 'NONE', *, *, #38126, .F. ) ; +#16823 = STYLED_ITEM ( 'NONE', ( #98257 ), #21297 ) ; +#16824 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#16825 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.1000000000000020040, 0.8299999999999999600 ) ) ; +#16826 = ORIENTED_EDGE ( 'NONE', *, *, #83659, .T. ) ; +#16827 = FILL_AREA_STYLE ('',( #15312 ) ) ; +#16828 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45065 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89599, #80965, #42143 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16829 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38772 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8511, #33108, #17755 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16830 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16831 = DIRECTION ( 'NONE', ( 1.649990468822289917E-78, -1.000000000000000000, 3.396003576002217664E-125 ) ) ; +#16832 = ORIENTED_EDGE ( 'NONE', *, *, #62935, .T. ) ; +#16833 = SURFACE_STYLE_USAGE ( .BOTH. , #94950 ) ; +#16834 = EDGE_CURVE ( 'NONE', #36712, #32201, #51937, .T. ) ; +#16835 = EDGE_CURVE ( 'NONE', #90763, #41637, #21772, .T. ) ; +#16836 = CARTESIAN_POINT ( 'NONE', ( 1.102257911893530062, -1.419390247362990021, 0.8100000000000000533 ) ) ; +#16837 = LINE ( 'NONE', #10115, #38488 ) ; +#16838 = VECTOR ( 'NONE', #78510, 1000.000000000000000 ) ; +#16839 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64194 ) ) ; +#16840 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#16841 = DIRECTION ( 'NONE', ( -0.7071067811865480168, -0.7071067811865470176, 0.000000000000000000 ) ) ; +#16842 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16843 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16844 = CARTESIAN_POINT ( 'NONE', ( -0.7453505133853431941, 1.552609075926967286, 0.8100000000000001643 ) ) ; +#16846 = VERTEX_POINT ( 'NONE', #5411 ) ; +#16845 = VERTEX_POINT ( 'NONE', #67224 ) ; +#16847 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16848 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#16849 = PLANE ( 'NONE', #60498 ) ; +#16850 = VECTOR ( 'NONE', #4762, 1000.000000000000114 ) ; +#16851 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#16852 = ORIENTED_EDGE ( 'NONE', *, *, #27447, .T. ) ; +#16853 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#16854 = AXIS2_PLACEMENT_3D ( 'NONE', #39131, #68737, #22296 ) ; +#16855 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16856 = ORIENTED_EDGE ( 'NONE', *, *, #25116, .T. ) ; +#16857 = EDGE_CURVE ( 'NONE', #94446, #30033, #21110, .T. ) ; +#16858 = VERTEX_POINT ( 'NONE', #98795 ) ; +#16859 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16860 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16861 = CARTESIAN_POINT ( 'NONE', ( -0.2258383435392919969, -1.079063990458370093, 0.8300000000000000711 ) ) ; +#16862 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16863 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16864 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16865 = ORIENTED_EDGE ( 'NONE', *, *, #58113, .T. ) ; +#16866 = VERTEX_POINT ( 'NONE', #12531 ) ; +#16867 = SURFACE_STYLE_USAGE ( .BOTH. , #8637 ) ; +#16868 = VERTEX_POINT ( 'NONE', #52430 ) ; +#16869 = LINE ( 'NONE', #94483, #16598 ) ; +#16870 = AXIS2_PLACEMENT_3D ( 'NONE', #11397, #41642, #40633 ) ; +#16872 = ORIENTED_EDGE ( 'NONE', *, *, #57147, .T. ) ; +#16871 = LINE ( 'NONE', #94488, #52618 ) ; +#16873 = EDGE_CURVE ( 'NONE', #98494, #80334, #28928, .T. ) ; +#16874 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16875 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16876 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62631 ), #18571 ) ; +#16877 = EDGE_LOOP ( 'NONE', ( #37644, #56001, #75813, #57156 ) ) ; +#16878 = SURFACE_SIDE_STYLE ('',( #54739 ) ) ; +#16879 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16880 = ORIENTED_EDGE ( 'NONE', *, *, #67683, .F. ) ; +#16881 = ADVANCED_FACE ( 'NONE', ( #89711 ), #99297, .T. ) ; +#16882 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42907, #51095, #90363, #82228 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#16883 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, -0.9464466094067263136 ) ) ; +#16884 = FILL_AREA_STYLE ('',( #85335 ) ) ; +#16885 = CIRCLE ( 'NONE', #46238, 0.09406596738343675490 ) ; +#16886 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16887 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16888 = VECTOR ( 'NONE', #62864, 1000.000000000000000 ) ; +#16889 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16890 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8099999999998640510 ) ) ; +#16891 = EDGE_CURVE ( 'NONE', #18465, #61391, #82663, .T. ) ; +#16893 = LINE ( 'NONE', #79214, #2597 ) ; +#16892 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.009999999999999998473, -1.250000000000000000 ) ) ; +#16894 = CARTESIAN_POINT ( 'NONE', ( 1.583412716359319905, -1.066507643917919967, 0.8299999999999990719 ) ) ; +#16895 = EDGE_CURVE ( 'NONE', #65234, #10054, #60607, .T. ) ; +#16896 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#16897 = ORIENTED_EDGE ( 'NONE', *, *, #29097, .F. ) ; +#16898 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16899 = DIRECTION ( 'NONE', ( -0.7071067811865495711, -0.7071067811865455743, 0.000000000000000000 ) ) ; +#16900 = SURFACE_SIDE_STYLE ('',( #49106 ) ) ; +#16901 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16902 = FILL_AREA_STYLE ('',( #25620 ) ) ; +#16903 = PRESENTATION_STYLE_ASSIGNMENT (( #86892 ) ) ; +#16904 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -2.033333333333333659, 0.000000000000000000 ) ) ; +#16905 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#16906 = MANIFOLD_SOLID_BREP ( 'ÊäÈë186', #27431 ) ; +#16908 = STYLED_ITEM ( 'NONE', ( #27903 ), #28748 ) ; +#16907 = STYLED_ITEM ( 'NONE', ( #32842 ), #37967 ) ; +#16909 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3890 ) ) ; +#16910 = SURFACE_SIDE_STYLE ('',( #71066 ) ) ; +#16911 = EDGE_LOOP ( 'NONE', ( #46505, #74269, #49476, #87840 ) ) ; +#16912 = VECTOR ( 'NONE', #50756, 1000.000000000000000 ) ; +#16913 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#16915 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53852, #44172, #91634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16914 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#16916 = ORIENTED_EDGE ( 'NONE', *, *, #75207, .F. ) ; +#16917 = EDGE_CURVE ( 'NONE', #56475, #9858, #35123, .T. ) ; +#16918 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#16920 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16919 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#16921 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#16922 = PLANE ( 'NONE', #82667 ) ; +#16923 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16924 = VECTOR ( 'NONE', #97254, 1000.000000000000000 ) ; +#16925 = PRESENTATION_STYLE_ASSIGNMENT (( #24136 ) ) ; +#16926 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28250, 'distance_accuracy_value', 'NONE'); +#16927 = VERTEX_POINT ( 'NONE', #84070 ) ; +#16928 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#16929 = EDGE_CURVE ( 'NONE', #61605, #46370, #7876, .T. ) ; +#16930 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16931 = FILL_AREA_STYLE_COLOUR ( '', #43743 ) ; +#16932 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16933 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16934 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#16935 = STYLED_ITEM ( 'NONE', ( #35373 ), #67542 ) ; +#16936 = ADVANCED_FACE ( 'NONE', ( #45716 ), #100757, .T. ) ; +#16937 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16938 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68803 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42413, #73551, #61631 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16939 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#16940 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#16941 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16942 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#16943 = ORIENTED_EDGE ( 'NONE', *, *, #64613, .T. ) ; +#16944 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#16945 = EDGE_CURVE ( 'NONE', #83900, #98821, #94209, .T. ) ; +#16946 = CIRCLE ( 'NONE', #74051, 0.09999999999999939493 ) ; +#16947 = ORIENTED_EDGE ( 'NONE', *, *, #11548, .F. ) ; +#16948 = FILL_AREA_STYLE ('',( #9733 ) ) ; +#16949 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50340, 'distance_accuracy_value', 'NONE'); +#16950 = SURFACE_STYLE_USAGE ( .BOTH. , #40481 ) ; +#16951 = SURFACE_STYLE_FILL_AREA ( #72606 ) ; +#16952 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16953 = CYLINDRICAL_SURFACE ( 'NONE', #13368, 0.5799999999999999600 ) ; +#16954 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#16955 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#16956 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000003331, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#16957 = VECTOR ( 'NONE', #39864, 999.9999999999998863 ) ; +#16958 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#16959 = EDGE_LOOP ( 'NONE', ( #22545, #98406, #10457, #24506 ) ) ; +#16960 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.4999999999999993339, -5.977360615245821520E-90 ) ) ; +#16961 = LINE ( 'NONE', #63485, #12740 ) ; +#16962 = FILL_AREA_STYLE_COLOUR ( '', #80270 ) ; +#16963 = VERTEX_POINT ( 'NONE', #93184 ) ; +#16964 = CARTESIAN_POINT ( 'NONE', ( 1.211717937534670719, -1.227738040490834681, 0.8099999999998463984 ) ) ; +#16965 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#16966 = AXIS2_PLACEMENT_3D ( 'NONE', #62189, #6934, #100818 ) ; +#16967 = FACE_OUTER_BOUND ( 'NONE', #52587, .T. ) ; +#16968 = ORIENTED_EDGE ( 'NONE', *, *, #88130, .F. ) ; +#16969 = CIRCLE ( 'NONE', #7128, 0.09999999999999999167 ) ; +#16970 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39277 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72021, #33728, #80699 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16971 = EDGE_CURVE ( 'NONE', #83308, #95367, #23296, .T. ) ; +#16972 = ADVANCED_FACE ( 'NONE', ( #37619 ), #85562, .T. ) ; +#16973 = PLANE ( 'NONE', #58297 ) ; +#16974 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#16975 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#16976 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#16977 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#16978 = ORIENTED_EDGE ( 'NONE', *, *, #36505, .F. ) ; +#16979 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#16980 = MANIFOLD_SOLID_BREP ( 'ÊäÈë6', #87775 ) ; +#16981 = EDGE_LOOP ( 'NONE', ( #79794, #11645, #70473, #29936 ) ) ; +#16982 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39545 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5329, #19695, #35548 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#16983 = AXIS2_PLACEMENT_3D ( 'NONE', #26408, #88185, #34581 ) ; +#16984 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#16985 = EDGE_CURVE ( 'NONE', #46606, #62079, #72265, .T. ) ; +#16986 = VERTEX_POINT ( 'NONE', #16597 ) ; +#16987 = ADVANCED_FACE ( 'NONE', ( #71254 ), #35649, .F. ) ; +#16988 = VECTOR ( 'NONE', #15605, 1000.000000000000000 ) ; +#16989 = PLANE ( 'NONE', #56279 ) ; +#16990 = DIRECTION ( 'NONE', ( 2.356961244533699997E-16, -0.000000000000000000, 1.000000000000000000 ) ) ; +#16991 = FILL_AREA_STYLE ('',( #47144 ) ) ; +#16992 = LINE ( 'NONE', #48170, #2748 ) ; +#16993 = VERTEX_POINT ( 'NONE', #58136 ) ; +#16995 = VERTEX_POINT ( 'NONE', #81102 ) ; +#16994 = EDGE_LOOP ( 'NONE', ( #88495, #31123, #99682, #56168 ) ) ; +#16996 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#16997 = ORIENTED_EDGE ( 'NONE', *, *, #58416, .F. ) ; +#16998 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34983 ), #21896 ) ; +#16999 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, 0.000000000000000000 ) ) ; +#17000 = AXIS2_PLACEMENT_3D ( 'NONE', #60925, #92025, #78246 ) ; +#17001 = ORIENTED_EDGE ( 'NONE', *, *, #49791, .T. ) ; +#17002 = ORIENTED_EDGE ( 'NONE', *, *, #4655, .F. ) ; +#17004 = ADVANCED_FACE ( 'NONE', ( #66264 ), #89251, .T. ) ; +#17003 = AXIS2_PLACEMENT_3D ( 'NONE', #22564, #13838, #68000 ) ; +#17005 = SURFACE_SIDE_STYLE ('',( #55847 ) ) ; +#17007 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1350000000000000089 ) ) ; +#17006 = SURFACE_SIDE_STYLE ('',( #40532 ) ) ; +#17008 = STYLED_ITEM ( 'NONE', ( #13172 ), #68685 ) ; +#17009 = ORIENTED_EDGE ( 'NONE', *, *, #31867, .T. ) ; +#17010 = LINE ( 'NONE', #48191, #35862 ) ; +#17011 = SURFACE_STYLE_USAGE ( .BOTH. , #24735 ) ; +#17012 = ORIENTED_EDGE ( 'NONE', *, *, #75010, .T. ) ; +#17013 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17014 = EDGE_CURVE ( 'NONE', #2960, #36115, #81609, .T. ) ; +#17015 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#17016 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21914 ) ) ; +#17017 = EDGE_LOOP ( 'NONE', ( #62490, #87642, #88246, #24067 ) ) ; +#17018 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17019 = EDGE_LOOP ( 'NONE', ( #79057, #3389, #44599, #28222 ) ) ; +#17020 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17021 = SURFACE_STYLE_FILL_AREA ( #87000 ) ; +#17022 = ADVANCED_FACE ( 'NONE', ( #51964 ), #42290, .T. ) ; +#17023 = FILL_AREA_STYLE ('',( #8783 ) ) ; +#17024 = SURFACE_STYLE_USAGE ( .BOTH. , #85979 ) ; +#17026 = ADVANCED_FACE ( 'NONE', ( #96360 ), #26466, .F. ) ; +#17025 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17027 = STYLED_ITEM ( 'NONE', ( #49999 ), #71340 ) ; +#17028 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#17029 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39867 ) ) ; +#17030 = SURFACE_STYLE_USAGE ( .BOTH. , #47687 ) ; +#17031 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79089 ), #49737 ) ; +#17032 = EDGE_LOOP ( 'NONE', ( #29787, #90408, #1093 ) ) ; +#17033 = SURFACE_STYLE_FILL_AREA ( #95128 ) ; +#17034 = SURFACE_STYLE_USAGE ( .BOTH. , #85481 ) ; +#17035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79018 ) ) ; +#17036 = VECTOR ( 'NONE', #92151, 1000.000000000000000 ) ; +#17037 = SURFACE_SIDE_STYLE ('',( #56408 ) ) ; +#17038 = SURFACE_SIDE_STYLE ('',( #78350 ) ) ; +#17039 = VECTOR ( 'NONE', #100212, 1000.000000000000000 ) ; +#17040 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17041 = FILL_AREA_STYLE_COLOUR ( '', #77177 ) ; +#17042 = CARTESIAN_POINT ( 'NONE', ( 1.476179938779914602, -3.099999999999970335, 0.000000000000000000 ) ) ; +#17043 = EDGE_LOOP ( 'NONE', ( #23414, #24617, #60118, #39499 ) ) ; +#17044 = SURFACE_SIDE_STYLE ('',( #93114 ) ) ; +#17045 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.000000000000000000 ) ) ; +#17046 = ADVANCED_FACE ( 'NONE', ( #76925 ), #100775, .F. ) ; +#17047 = AXIS2_PLACEMENT_3D ( 'NONE', #39734, #70881, #928 ) ; +#17049 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17048 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753240063, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#17050 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, -0.2399999999999999911 ) ) ; +#17051 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15649, 'distance_accuracy_value', 'NONE'); +#17052 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17053 = CARTESIAN_POINT ( 'NONE', ( 0.2985587656685099733, -1.344342053265010106, 0.8299999999999999600 ) ) ; +#17054 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21950 ) ) ; +#17055 = STYLED_ITEM ( 'NONE', ( #90686 ), #20123 ) ; +#17056 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#17057 = VECTOR ( 'NONE', #98888, 1000.000000000000000 ) ; +#17058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17059 = ORIENTED_EDGE ( 'NONE', *, *, #81838, .T. ) ; +#17060 = EDGE_CURVE ( 'NONE', #6687, #7208, #21290, .T. ) ; +#17061 = PLANE ( 'NONE', #52218 ) ; +#17062 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17063 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#17065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17064 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51291 ), #21960 ) ; +#17066 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61126 ), #38223 ) ; +#17067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17068 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#17069 = EDGE_CURVE ( 'NONE', #98628, #22428, #6417, .T. ) ; +#17070 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8648700000000000276 ) ) ; +#17071 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17072 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77101 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65870, #48552, #17867 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17073 = SURFACE_STYLE_USAGE ( .BOTH. , #88053 ) ; +#17074 = CARTESIAN_POINT ( 'NONE', ( 1.145723413874399910, -1.437310919031880241, 0.8299999999999999600 ) ) ; +#17075 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#17076 = VERTEX_POINT ( 'NONE', #22811 ) ; +#17077 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17078 = EDGE_CURVE ( 'NONE', #5154, #54443, #92527, .T. ) ; +#17079 = VERTEX_POINT ( 'NONE', #38620 ) ; +#17080 = SURFACE_SIDE_STYLE ('',( #14027 ) ) ; +#17081 = PRESENTATION_STYLE_ASSIGNMENT (( #64082 ) ) ; +#17082 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6848 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1619, #79213, #78215 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17083 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17084 = FACE_OUTER_BOUND ( 'NONE', #36662, .T. ) ; +#17085 = SURFACE_SIDE_STYLE ('',( #57967 ) ) ; +#17086 = CARTESIAN_POINT ( 'NONE', ( -0.9365963522183331502, -1.249140550102370018, 0.8299999999999999600 ) ) ; +#17087 = ORIENTED_EDGE ( 'NONE', *, *, #20016, .F. ) ; +#17088 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#17089 = MANIFOLD_SOLID_BREP ( 'ÊäÈë24', #84410 ) ; +#17090 = AXIS2_PLACEMENT_3D ( 'NONE', #96601, #9268, #10250 ) ; +#17091 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17092 = EDGE_LOOP ( 'NONE', ( #100861, #82431, #72744, #72623 ) ) ; +#17093 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39197 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90889, #42430, #91876 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17094 = ADVANCED_FACE ( 'NONE', ( #25357 ), #32493, .T. ) ; +#17095 = EDGE_CURVE ( 'NONE', #65740, #8781, #63647, .T. ) ; +#17096 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17097 = PRESENTATION_STYLE_ASSIGNMENT (( #25313 ) ) ; +#17098 = VECTOR ( 'NONE', #6763, 1000.000000000000000 ) ; +#17099 = FILL_AREA_STYLE_COLOUR ( '', #86395 ) ; +#17100 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17101 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17102 = LINE ( 'NONE', #47254, #56109 ) ; +#17103 = VERTEX_POINT ( 'NONE', #55991 ) ; +#17104 = LINE ( 'NONE', #24824, #12944 ) ; +#17105 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89954, 'distance_accuracy_value', 'NONE'); +#17106 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.009999999999999998473, 1.250000000000000000 ) ) ; +#17107 = SURFACE_STYLE_FILL_AREA ( #87084 ) ; +#17108 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87231 ) ) ; +#17109 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#17110 = ORIENTED_EDGE ( 'NONE', *, *, #20215, .F. ) ; +#17111 = VECTOR ( 'NONE', #56234, 1000.000000000000000 ) ; +#17112 = EDGE_CURVE ( 'NONE', #65708, #90971, #64140, .T. ) ; +#17113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79101 ), #44795 ) ; +#17114 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17115 = SURFACE_SIDE_STYLE ('',( #25328 ) ) ; +#17116 = FILL_AREA_STYLE ('',( #33483 ) ) ; +#17117 = EDGE_LOOP ( 'NONE', ( #54720, #89562, #35275, #69755, #1272, #9995 ) ) ; +#17118 = SURFACE_STYLE_FILL_AREA ( #48313 ) ; +#17119 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#17120 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29777 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12429, #51335, #96737 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17121 = VECTOR ( 'NONE', #20242, 1000.000000000000000 ) ; +#17123 = EDGE_CURVE ( 'NONE', #87714, #28792, #77931, .T. ) ; +#17122 = FILL_AREA_STYLE ('',( #32471 ) ) ; +#17124 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17125 = VECTOR ( 'NONE', #52432, 1000.000000000000000 ) ; +#17126 = VERTEX_POINT ( 'NONE', #47286 ) ; +#17127 = ORIENTED_EDGE ( 'NONE', *, *, #90372, .F. ) ; +#17128 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19106, 'distance_accuracy_value', 'NONE'); +#17129 = SURFACE_STYLE_USAGE ( .BOTH. , #16602 ) ; +#17130 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17131 = AXIS2_PLACEMENT_3D ( 'NONE', #66581, #12385, #71874 ) ; +#17132 = ORIENTED_EDGE ( 'NONE', *, *, #20818, .F. ) ; +#17133 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17134 = STYLED_ITEM ( 'NONE', ( #97176 ), #98850 ) ; +#17135 = ORIENTED_EDGE ( 'NONE', *, *, #90835, .T. ) ; +#17136 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#17137 = ORIENTED_EDGE ( 'NONE', *, *, #5039, .T. ) ; +#17138 = EDGE_LOOP ( 'NONE', ( #23775, #98033, #97921, #41030, #77933, #42317, #44274, #47816 ) ) ; +#17139 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#17141 = SURFACE_STYLE_USAGE ( .BOTH. , #85589 ) ; +#17140 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#17142 = SURFACE_STYLE_USAGE ( .BOTH. , #87118 ) ; +#17143 = ADVANCED_FACE ( 'NONE', ( #70258 ), #94233, .T. ) ; +#17144 = ORIENTED_EDGE ( 'NONE', *, *, #71484, .F. ) ; +#17145 = VECTOR ( 'NONE', #18115, 1000.000000000000000 ) ; +#17146 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#17147 = MANIFOLD_SOLID_BREP ( 'ÊäÈë109', #74670 ) ; +#17148 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17149 = VERTEX_POINT ( 'NONE', #66630 ) ; +#17150 = SURFACE_SIDE_STYLE ('',( #57518 ) ) ; +#17151 = EDGE_LOOP ( 'NONE', ( #85170, #63881, #18894, #98 ) ) ; +#17152 = ORIENTED_EDGE ( 'NONE', *, *, #52740, .F. ) ; +#17153 = FILL_AREA_STYLE ('',( #95243 ) ) ; +#17154 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#17155 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17156 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#17157 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17159 = PLANE ( 'NONE', #5675 ) ; +#17158 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#17160 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17161 = VECTOR ( 'NONE', #14738, 1000.000000000000000 ) ; +#17162 = SURFACE_STYLE_USAGE ( .BOTH. , #8935 ) ; +#17163 = FILL_AREA_STYLE_COLOUR ( '', #67886 ) ; +#17164 = ORIENTED_EDGE ( 'NONE', *, *, #56522, .T. ) ; +#17166 = VECTOR ( 'NONE', #81751, 1000.000000000000114 ) ; +#17165 = LINE ( 'NONE', #72833, #15402 ) ; +#17167 = EDGE_CURVE ( 'NONE', #91027, #3831, #80467, .T. ) ; +#17169 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#17168 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, -7.771561172376096523E-17, -1.000000000000000000 ) ) ; +#17170 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#17171 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17172 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33547 ), #36801 ) ; +#17173 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#17174 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#17175 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999986011, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#17176 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17177 = VERTEX_POINT ( 'NONE', #3359 ) ; +#17179 = EDGE_CURVE ( 'NONE', #12058, #13557, #11923, .T. ) ; +#17178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18856 ) ) ; +#17180 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17182 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19024, 'distance_accuracy_value', 'NONE'); +#17181 = PLANE ( 'NONE', #77080 ) ; +#17183 = FILL_AREA_STYLE_COLOUR ( '', #55432 ) ; +#17184 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26994 ) ) ; +#17186 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -0.1499999999999999944 ) ) ; +#17185 = VECTOR ( 'NONE', #91915, 1000.000000000000000 ) ; +#17187 = SURFACE_SIDE_STYLE ('',( #71841 ) ) ; +#17188 = LINE ( 'NONE', #78479, #13741 ) ; +#17189 = AXIS2_PLACEMENT_3D ( 'NONE', #83470, #61509, #77292 ) ; +#17190 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82456 ), #51500 ) ; +#17191 = AXIS2_PLACEMENT_3D ( 'NONE', #93910, #48008, #54156 ) ; +#17192 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#17193 = PRESENTATION_STYLE_ASSIGNMENT (( #94787 ) ) ; +#17194 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#17195 = PRESENTATION_STYLE_ASSIGNMENT (( #23892 ) ) ; +#17196 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17197 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17198 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17199 = EDGE_CURVE ( 'NONE', #66220, #62005, #50842, .T. ) ; +#17200 = FACE_OUTER_BOUND ( 'NONE', #34622, .T. ) ; +#17201 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17202 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17203 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78837 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100123, #61465, #38962 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17205 = EDGE_CURVE ( 'NONE', #36748, #8845, #89367, .T. ) ; +#17204 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#17206 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17207 = VERTEX_POINT ( 'NONE', #96251 ) ; +#17208 = LINE ( 'NONE', #56056, #83691 ) ; +#17209 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.297402597402600000, 0.8299999999999999600 ) ) ; +#17210 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#17212 = SURFACE_STYLE_USAGE ( .BOTH. , #17712 ) ; +#17211 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#17213 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17214 = DIRECTION ( 'NONE', ( 0.7071060119555152568, -0.7071075504167430026, 0.000000000000000000 ) ) ; +#17215 = EDGE_CURVE ( 'NONE', #97931, #92419, #42665, .T. ) ; +#17216 = ADVANCED_FACE ( 'NONE', ( #73312 ), #20158, .T. ) ; +#17217 = AXIS2_PLACEMENT_3D ( 'NONE', #62371, #8133, #69992 ) ; +#17218 = LINE ( 'NONE', #48898, #44420 ) ; +#17219 = LINE ( 'NONE', #2934, #76115 ) ; +#17220 = ORIENTED_EDGE ( 'NONE', *, *, #8266, .F. ) ; +#17221 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#17222 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17223 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32547 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72163, #72659, #33377 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17224 = EDGE_CURVE ( 'NONE', #48821, #80892, #98207, .T. ) ; +#17225 = EDGE_CURVE ( 'NONE', #19424, #95596, #57503, .T. ) ; +#17226 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17227 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17228 = VERTEX_POINT ( 'NONE', #76801 ) ; +#17229 = ORIENTED_EDGE ( 'NONE', *, *, #95677, .F. ) ; +#17230 = EDGE_CURVE ( 'NONE', #84573, #1971, #12934, .T. ) ; +#17231 = FACE_OUTER_BOUND ( 'NONE', #1157, .T. ) ; +#17232 = EDGE_LOOP ( 'NONE', ( #9094, #74401, #62633, #3601, #83875, #12543 ) ) ; +#17233 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17234 = PRESENTATION_STYLE_ASSIGNMENT (( #47893 ) ) ; +#17235 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17236 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17237 = PLANE ( 'NONE', #92045 ) ; +#17238 = EDGE_CURVE ( 'NONE', #38264, #18135, #71435, .T. ) ; +#17239 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #38474 ) ; +#17240 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#17242 = ORIENTED_EDGE ( 'NONE', *, *, #37123, .F. ) ; +#17241 = EDGE_LOOP ( 'NONE', ( #36700, #11514, #36675, #11217 ) ) ; +#17243 = ORIENTED_EDGE ( 'NONE', *, *, #100458, .T. ) ; +#17244 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#17245 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87377 ) ) ; +#17246 = VECTOR ( 'NONE', #3052, 1000.000000000000000 ) ; +#17247 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84975, 'distance_accuracy_value', 'NONE'); +#17248 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68227 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16397, #93502, #40446 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17250 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#17249 = CARTESIAN_POINT ( 'NONE', ( 0.5421186041101929698, -1.033429037169790066, 0.8100000000000000533 ) ) ; +#17251 = EDGE_LOOP ( 'NONE', ( #23713, #24464, #85141, #97262 ) ) ; +#17252 = MANIFOLD_SOLID_BREP ( 'ÊäÈë15', #19239 ) ; +#17253 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.35000000000000142, 0.000000000000000000 ) ) ; +#17254 = STYLED_ITEM ( 'NONE', ( #22174 ), #83004 ) ; +#17255 = VECTOR ( 'NONE', #35716, 1000.000000000000000 ) ; +#17256 = ORIENTED_EDGE ( 'NONE', *, *, #68761, .T. ) ; +#17257 = VERTEX_POINT ( 'NONE', #30838 ) ; +#17258 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77761 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54613, #85709, #45373 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17259 = VECTOR ( 'NONE', #37728, 1000.000000000000000 ) ; +#17260 = PRESENTATION_STYLE_ASSIGNMENT (( #1469 ) ) ; +#17261 = ORIENTED_EDGE ( 'NONE', *, *, #69943, .F. ) ; +#17262 = ORIENTED_EDGE ( 'NONE', *, *, #63697, .T. ) ; +#17263 = CARTESIAN_POINT ( 'NONE', ( 0.3455761866733689791, -1.312343239366150049, 0.8300000000000004041 ) ) ; +#17264 = VECTOR ( 'NONE', #63761, 1000.000000000000000 ) ; +#17265 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17266 = AXIS2_PLACEMENT_3D ( 'NONE', #92863, #14756, #16273 ) ; +#17267 = LINE ( 'NONE', #48459, #17889 ) ; +#17269 = VERTEX_POINT ( 'NONE', #61009 ) ; +#17268 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#17270 = FILL_AREA_STYLE_COLOUR ( '', #47445 ) ; +#17271 = VECTOR ( 'NONE', #83177, 1000.000000000000000 ) ; +#17272 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17273 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -2.350550309948575893E-17, 0.4000000000000000777 ) ) ; +#17274 = ORIENTED_EDGE ( 'NONE', *, *, #37259, .T. ) ; +#17275 = FILL_AREA_STYLE ('',( #78560 ) ) ; +#17276 = CARTESIAN_POINT ( 'NONE', ( 0.06704264972532250622, -1.237898259965849901, 0.8299999999999999600 ) ) ; +#17277 = ORIENTED_EDGE ( 'NONE', *, *, #87492, .T. ) ; +#17278 = EDGE_CURVE ( 'NONE', #65042, #71240, #69093, .T. ) ; +#17279 = ORIENTED_EDGE ( 'NONE', *, *, #71299, .T. ) ; +#17280 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17281 = CARTESIAN_POINT ( 'NONE', ( 1.765390738874589971, -1.428263396816370046, 0.8300000000000002931 ) ) ; +#17282 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17283 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#17284 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28040 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46967, #100468, #23007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17285 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17286 = PRESENTATION_STYLE_ASSIGNMENT (( #87243 ) ) ; +#17287 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76013 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46845, #76999, #78020 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17288 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#17289 = SURFACE_STYLE_FILL_AREA ( #47442 ) ; +#17290 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98143, 'distance_accuracy_value', 'NONE'); +#17291 = VECTOR ( 'NONE', #68365, 1000.000000000000000 ) ; +#17292 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17293 = ORIENTED_EDGE ( 'NONE', *, *, #81494, .F. ) ; +#17294 = FILL_AREA_STYLE ('',( #71948 ) ) ; +#17295 = CARTESIAN_POINT ( 'NONE', ( -0.01004137219608649927, -1.188470249711290228, 0.8299999999999999600 ) ) ; +#17296 = ORIENTED_EDGE ( 'NONE', *, *, #74185, .F. ) ; +#17297 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.700000000000000178, 0.000000000000000000 ) ) ; +#17298 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17299 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18905 ), #33670 ) ; +#17300 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17301 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17302 = PLANE ( 'NONE', #15766 ) ; +#17303 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17304 = DIRECTION ( 'NONE', ( -1.000000000000000000, -2.168404344971010051E-15, 0.000000000000000000 ) ) ; +#17305 = SURFACE_STYLE_FILL_AREA ( #39803 ) ; +#17306 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.000000000000000000 ) ) ; +#17307 = PRESENTATION_STYLE_ASSIGNMENT (( #70952 ) ) ; +#17308 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000762, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#17309 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17310 = FILL_AREA_STYLE_COLOUR ( '', #36570 ) ; +#17311 = STYLED_ITEM ( 'NONE', ( #56277 ), #30272 ) ; +#17312 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17313 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17314 = LINE ( 'NONE', #9588, #74008 ) ; +#17315 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #48514 ) ; +#17316 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99542, #28689, #60866, #67964 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#17317 = AXIS2_PLACEMENT_3D ( 'NONE', #34066, #18183, #65180 ) ; +#17318 = ORIENTED_EDGE ( 'NONE', *, *, #70534, .F. ) ; +#17319 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17320 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17321 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78728, 'distance_accuracy_value', 'NONE'); +#17322 = ORIENTED_EDGE ( 'NONE', *, *, #25172, .T. ) ; +#17324 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59919, 'distance_accuracy_value', 'NONE'); +#17323 = FACE_OUTER_BOUND ( 'NONE', #99878, .T. ) ; +#17325 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4699999999999999734, 0.2250000000000000333 ) ) ; +#17327 = STYLED_ITEM ( 'NONE', ( #25724 ), #83096 ) ; +#17326 = LINE ( 'NONE', #33179, #9236 ) ; +#17328 = SURFACE_STYLE_USAGE ( .BOTH. , #87289 ) ; +#17329 = FACE_OUTER_BOUND ( 'NONE', #38704, .T. ) ; +#17330 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#17331 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, -0.09999999999999988065, -0.02000000000000000042 ) ) ; +#17332 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100958 ) ; +#17333 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#17334 = ORIENTED_EDGE ( 'NONE', *, *, #45440, .T. ) ; +#17335 = ORIENTED_EDGE ( 'NONE', *, *, #24699, .T. ) ; +#17336 = VECTOR ( 'NONE', #8435, 1000.000000000000000 ) ; +#17337 = PRESENTATION_STYLE_ASSIGNMENT (( #32691 ) ) ; +#17338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72357, 'distance_accuracy_value', 'NONE'); +#17339 = LINE ( 'NONE', #92903, #84095 ) ; +#17340 = FACE_OUTER_BOUND ( 'NONE', #65768, .T. ) ; +#17341 = EDGE_CURVE ( 'NONE', #10271, #89499, #30313, .T. ) ; +#17342 = LINE ( 'NONE', #48006, #8045 ) ; +#17343 = LINE ( 'NONE', #3058, #63242 ) ; +#17344 = PRESENTATION_STYLE_ASSIGNMENT (( #25060 ) ) ; +#17345 = ORIENTED_EDGE ( 'NONE', *, *, #53211, .T. ) ; +#17346 = CARTESIAN_POINT ( 'NONE', ( 1.060148841163599975, -1.043393888298179917, 0.8300000000000002931 ) ) ; +#17348 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69563 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46933, #85242, #84250 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17347 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#17349 = EDGE_LOOP ( 'NONE', ( #42200, #59883, #11445, #23309 ) ) ; +#17350 = SURFACE_STYLE_USAGE ( .BOTH. , #36607 ) ; +#17351 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58161 ), #61419 ) ; +#17352 = FACE_OUTER_BOUND ( 'NONE', #53683, .T. ) ; +#17353 = ORIENTED_EDGE ( 'NONE', *, *, #53753, .F. ) ; +#17354 = PLANE ( 'NONE', #37585 ) ; +#17355 = AXIS2_PLACEMENT_3D ( 'NONE', #25672, #2694, #87942 ) ; +#17356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17357 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17358 = CARTESIAN_POINT ( 'NONE', ( -1.118667357395492168, 2.226822044640270448, 0.8100000000000001643 ) ) ; +#17359 = EDGE_CURVE ( 'NONE', #12243, #90220, #68625, .T. ) ; +#17360 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58167 ) ) ; +#17361 = FILL_AREA_STYLE_COLOUR ( '', #47895 ) ; +#17362 = FACE_OUTER_BOUND ( 'NONE', #4123, .T. ) ; +#17363 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000000804, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#17364 = FACE_OUTER_BOUND ( 'NONE', #42584, .T. ) ; +#17366 = VERTEX_POINT ( 'NONE', #22176 ) ; +#17365 = VERTEX_POINT ( 'NONE', #92114 ) ; +#17367 = CIRCLE ( 'NONE', #28741, 0.2137111836784290342 ) ; +#17368 = PRESENTATION_STYLE_ASSIGNMENT (( #29794 ) ) ; +#17369 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.100000000000000089, -3.118622929693471946E-90 ) ) ; +#17370 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8648700000000000276 ) ) ; +#17371 = ORIENTED_EDGE ( 'NONE', *, *, #58990, .T. ) ; +#17372 = STYLED_ITEM ( 'NONE', ( #45584 ), #13163 ) ; +#17373 = FACE_OUTER_BOUND ( 'NONE', #100487, .T. ) ; +#17375 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17374 = LINE ( 'NONE', #80208, #41010 ) ; +#17376 = ORIENTED_EDGE ( 'NONE', *, *, #30200, .T. ) ; +#17377 = VERTEX_POINT ( 'NONE', #6767 ) ; +#17378 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8199999999999999512 ) ) ; +#17379 = DIRECTION ( 'NONE', ( -1.355252715606876105E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17380 = LINE ( 'NONE', #72517, #8748 ) ; +#17381 = PLANE ( 'NONE', #35660 ) ; +#17382 = FACE_OUTER_BOUND ( 'NONE', #30947, .T. ) ; +#17383 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17384 = VERTEX_POINT ( 'NONE', #84464 ) ; +#17385 = VERTEX_POINT ( 'NONE', #38509 ) ; +#17386 = LINE ( 'NONE', #9159, #32344 ) ; +#17387 = ORIENTED_EDGE ( 'NONE', *, *, #24612, .F. ) ; +#17388 = FACE_OUTER_BOUND ( 'NONE', #13064, .T. ) ; +#17389 = STYLED_ITEM ( 'NONE', ( #83374 ), #30216 ) ; +#17391 = VERTEX_POINT ( 'NONE', #38015 ) ; +#17390 = FILL_AREA_STYLE ('',( #64880 ) ) ; +#17392 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311421000000000170, 0.8648700000000000276 ) ) ; +#17393 = PRESENTATION_STYLE_ASSIGNMENT (( #70006 ) ) ; +#17394 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17395 = ORIENTED_EDGE ( 'NONE', *, *, #75727, .T. ) ; +#17396 = CYLINDRICAL_SURFACE ( 'NONE', #74605, 0.2500000000000001110 ) ; +#17397 = ORIENTED_EDGE ( 'NONE', *, *, #68761, .F. ) ; +#17398 = EDGE_CURVE ( 'NONE', #46873, #68530, #14475, .T. ) ; +#17399 = STYLED_ITEM ( 'NONE', ( #17816 ), #54659 ) ; +#17400 = CARTESIAN_POINT ( 'NONE', ( -1.450000000000000178, 0.6892893218813453959, -0.9757359312880719004 ) ) ; +#17401 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18729 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48466, #10040, #10532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17402 = SURFACE_STYLE_FILL_AREA ( #71 ) ; +#17403 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17404 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#17405 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01500000000000000118, 0.000000000000000000 ) ) ; +#17407 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17406 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17408 = LINE ( 'NONE', #64902, #34412 ) ; +#17409 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69587 ), #30430 ) ; +#17410 = FILL_AREA_STYLE_COLOUR ( '', #26764 ) ; +#17411 = ORIENTED_EDGE ( 'NONE', *, *, #94434, .F. ) ; +#17412 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17413 = SURFACE_STYLE_USAGE ( .BOTH. , #16900 ) ; +#17414 = CIRCLE ( 'NONE', #58221, 0.2000000000066392836 ) ; +#17415 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54926 ), #10785 ) ; +#17416 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#17418 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17417 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000019984, 0.1829999999999659954 ) ) ; +#17419 = SURFACE_STYLE_USAGE ( .BOTH. , #87380 ) ; +#17420 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#17421 = MANIFOLD_SOLID_BREP ( 'ÊäÈë49', #42015 ) ; +#17422 = EDGE_CURVE ( 'NONE', #97231, #77277, #38119, .T. ) ; +#17423 = VECTOR ( 'NONE', #63958, 1000.000000000000000 ) ; +#17424 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#17425 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11373, #81932, #19617, #50795 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#17426 = AXIS2_PLACEMENT_3D ( 'NONE', #10236, #58355, #66467 ) ; +#17427 = PRESENTATION_STYLE_ASSIGNMENT (( #24126 ) ) ; +#17428 = ORIENTED_EDGE ( 'NONE', *, *, #47782, .F. ) ; +#17429 = FACE_OUTER_BOUND ( 'NONE', #98114, .T. ) ; +#17430 = FACE_OUTER_BOUND ( 'NONE', #55355, .T. ) ; +#17431 = SURFACE_STYLE_FILL_AREA ( #87398 ) ; +#17432 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17433 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17434 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17435 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31375, #78358, #85490, #30863 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#17436 = ORIENTED_EDGE ( 'NONE', *, *, #89023, .T. ) ; +#17437 = SURFACE_STYLE_FILL_AREA ( #87406 ) ; +#17438 = EDGE_CURVE ( 'NONE', #20826, #90971, #24745, .T. ) ; +#17439 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17440 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#17441 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, -3.500000000000000444, 0.000000000000000000 ) ) ; +#17442 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72875 ), #79439 ) ; +#17443 = LINE ( 'NONE', #7204, #69130 ) ; +#17444 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30283, 'distance_accuracy_value', 'NONE'); +#17445 = LINE ( 'NONE', #85900, #43726 ) ; +#17446 = STYLED_ITEM ( 'NONE', ( #36301 ), #30508 ) ; +#17447 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#17448 = VERTEX_POINT ( 'NONE', #62014 ) ; +#17449 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#17450 = ORIENTED_EDGE ( 'NONE', *, *, #32782, .F. ) ; +#17451 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17452 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39273, 'distance_accuracy_value', 'NONE'); +#17453 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80138, 'distance_accuracy_value', 'NONE'); +#17454 = SURFACE_STYLE_USAGE ( .BOTH. , #73124 ) ; +#17455 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17456 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#17457 = ADVANCED_FACE ( 'NONE', ( #70138 ), #31342, .F. ) ; +#17458 = CARTESIAN_POINT ( 'NONE', ( -0.01460762007543630128, -1.490633633148249926, 0.8300000000000004041 ) ) ; +#17459 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, -0.3000000000000001554, -0.02000000000000000042 ) ) ; +#17460 = PRESENTATION_STYLE_ASSIGNMENT (( #3172 ) ) ; +#17461 = FILL_AREA_STYLE_COLOUR ( '', #31451 ) ; +#17462 = ORIENTED_EDGE ( 'NONE', *, *, #5315, .F. ) ; +#17463 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17465 = LINE ( 'NONE', #15442, #4248 ) ; +#17464 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17466 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#17467 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1574, 'distance_accuracy_value', 'NONE'); +#17468 = ORIENTED_EDGE ( 'NONE', *, *, #40070, .F. ) ; +#17469 = PLANE ( 'NONE', #21655 ) ; +#17470 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17471 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#17472 = VERTEX_POINT ( 'NONE', #47680 ) ; +#17473 = DIRECTION ( 'NONE', ( 2.058195874565369951E-47, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17474 = FILL_AREA_STYLE_COLOUR ( '', #42986 ) ; +#17475 = ADVANCED_FACE ( 'NONE', ( #63027 ), #86485, .T. ) ; +#17476 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25609 ), #2786 ) ; +#17477 = PRESENTATION_STYLE_ASSIGNMENT (( #70092 ) ) ; +#17478 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17479 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.523820061220085176, -0.02000000000000000042 ) ) ; +#17481 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.449999999999999956, -11.90660254037844012 ) ) ; +#17480 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61547 ), #14231 ) ; +#17482 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17483 = VERTEX_POINT ( 'NONE', #97970 ) ; +#17484 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17486 = VECTOR ( 'NONE', #84512, 1000.000000000000114 ) ; +#17485 = PLANE ( 'NONE', #26770 ) ; +#17487 = ORIENTED_EDGE ( 'NONE', *, *, #97253, .F. ) ; +#17488 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#17489 = VECTOR ( 'NONE', #78155, 1000.000000000000000 ) ; +#17490 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17491 = CLOSED_SHELL ( 'NONE', ( #73761, #66585, #19227, #94968, #94308, #50819 ) ) ; +#17492 = ORIENTED_EDGE ( 'NONE', *, *, #93753, .T. ) ; +#17493 = PRESENTATION_STYLE_ASSIGNMENT (( #42521 ) ) ; +#17494 = CARTESIAN_POINT ( 'NONE', ( 1.745101982296789922, -0.9718760589866800581, 0.8300000000000004041 ) ) ; +#17495 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17496 = FILL_AREA_STYLE ('',( #95088 ) ) ; +#17497 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17498 = PRESENTATION_STYLE_ASSIGNMENT (( #675 ) ) ; +#17499 = EDGE_LOOP ( 'NONE', ( #94273, #46075, #20421, #100403 ) ) ; +#17501 = EDGE_LOOP ( 'NONE', ( #25821, #10081, #12343, #72904, #1609, #4095 ) ) ; +#17500 = VERTEX_POINT ( 'NONE', #66889 ) ; +#17502 = EDGE_LOOP ( 'NONE', ( #13142, #29308, #10214, #64489 ) ) ; +#17503 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17504 = EDGE_CURVE ( 'NONE', #63310, #33704, #22366, .T. ) ; +#17505 = ORIENTED_EDGE ( 'NONE', *, *, #59077, .F. ) ; +#17507 = VERTEX_POINT ( 'NONE', #75081 ) ; +#17506 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8648700000000000276 ) ) ; +#17508 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17509 = ORIENTED_EDGE ( 'NONE', *, *, #73945, .T. ) ; +#17510 = FACE_OUTER_BOUND ( 'NONE', #53757, .T. ) ; +#17511 = CARTESIAN_POINT ( 'NONE', ( 1.817674829793840319, -1.368793146596559929, 0.8099999999999997202 ) ) ; +#17512 = ORIENTED_EDGE ( 'NONE', *, *, #68602, .F. ) ; +#17513 = EDGE_CURVE ( 'NONE', #41785, #100489, #35294, .T. ) ; +#17514 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17515 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90293 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3926, #42742, #13023 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17516 = ORIENTED_EDGE ( 'NONE', *, *, #51302, .F. ) ; +#17517 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7603 ) ) ; +#17518 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8991599999999999593 ) ) ; +#17519 = ORIENTED_EDGE ( 'NONE', *, *, #93494, .F. ) ; +#17520 = PLANE ( 'NONE', #93782 ) ; +#17521 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17522 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17523 = SURFACE_STYLE_FILL_AREA ( #25735 ) ; +#17524 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17525 = PLANE ( 'NONE', #66250 ) ; +#17526 = LINE ( 'NONE', #48722, #4679 ) ; +#17527 = SURFACE_SIDE_STYLE ('',( #55388 ) ) ; +#17528 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.084202172485506406E-15, 0.000000000000000000 ) ) ; +#17529 = VECTOR ( 'NONE', #22106, 1000.000000000000000 ) ; +#17530 = SURFACE_STYLE_USAGE ( .BOTH. , #17037 ) ; +#17531 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8100000000000000533 ) ) ; +#17532 = ORIENTED_EDGE ( 'NONE', *, *, #82733, .T. ) ; +#17533 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17534 = ADVANCED_FACE ( 'NONE', ( #13199 ), #89872, .T. ) ; +#17535 = SURFACE_SIDE_STYLE ('',( #15513 ) ) ; +#17536 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17537 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17538 = EDGE_LOOP ( 'NONE', ( #60235, #78356, #45491, #63773 ) ) ; +#17539 = SURFACE_STYLE_FILL_AREA ( #56417 ) ; +#17540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17541 = AXIS2_PLACEMENT_3D ( 'NONE', #94010, #14898, #92520 ) ; +#17542 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77911 ), #55140 ) ; +#17543 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#17544 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#17545 = SURFACE_STYLE_USAGE ( .BOTH. , #40061 ) ; +#17546 = CIRCLE ( 'NONE', #33858, 0.5799999999999999600 ) ; +#17547 = STYLED_ITEM ( 'NONE', ( #60720 ), #16572 ) ; +#17548 = AXIS2_PLACEMENT_3D ( 'NONE', #45823, #24949, #16700 ) ; +#17549 = FILL_AREA_STYLE_COLOUR ( '', #42127 ) ; +#17550 = CLOSED_SHELL ( 'NONE', ( #39021, #69538, #43732, #92546, #83226, #37425 ) ) ; +#17551 = ORIENTED_EDGE ( 'NONE', *, *, #40308, .T. ) ; +#17552 = FACE_OUTER_BOUND ( 'NONE', #17241, .T. ) ; +#17553 = ADVANCED_FACE ( 'NONE', ( #28591 ), #74574, .F. ) ; +#17554 = VECTOR ( 'NONE', #44425, 1000.000000000000000 ) ; +#17555 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 6.695483000000000295, 0.8648700000000000276 ) ) ; +#17556 = LINE ( 'NONE', #93630, #11363 ) ; +#17557 = EDGE_CURVE ( 'NONE', #10872, #24588, #70397, .T. ) ; +#17558 = VECTOR ( 'NONE', #44832, 1000.000000000000000 ) ; +#17559 = SURFACE_STYLE_USAGE ( .BOTH. , #79379 ) ; +#17560 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17561 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17562 = LINE ( 'NONE', #97662, #75890 ) ; +#17563 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81179 ) ) ; +#17564 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#17565 = FILL_AREA_STYLE ('',( #10854 ) ) ; +#17566 = FACE_OUTER_BOUND ( 'NONE', #67573, .T. ) ; +#17567 = SURFACE_SIDE_STYLE ('',( #33442 ) ) ; +#17568 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17569 = SURFACE_SIDE_STYLE ('',( #71724 ) ) ; +#17570 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17571 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86027 ), #30603 ) ; +#17572 = LINE ( 'NONE', #32928, #48718 ) ; +#17573 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#17574 = ORIENTED_EDGE ( 'NONE', *, *, #29999, .T. ) ; +#17575 = ORIENTED_EDGE ( 'NONE', *, *, #49063, .T. ) ; +#17576 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55615, 'distance_accuracy_value', 'NONE'); +#17577 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14251, 'distance_accuracy_value', 'NONE'); +#17578 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59348 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82650, #83663, #4522 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17579 = EDGE_CURVE ( 'NONE', #21443, #36748, #45878, .T. ) ; +#17580 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#17581 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17582 = SURFACE_STYLE_FILL_AREA ( #72743 ) ; +#17584 = ORIENTED_EDGE ( 'NONE', *, *, #70468, .T. ) ; +#17583 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84496 ), #42372 ) ; +#17585 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#17586 = MANIFOLD_SOLID_BREP ( 'ÊäÈë182', #66421 ) ; +#17587 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17588 = EDGE_CURVE ( 'NONE', #80853, #90990, #23455, .T. ) ; +#17589 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12971, 'distance_accuracy_value', 'NONE'); +#17590 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#17591 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3440 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31889, #39546, #55406 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17592 = VERTEX_POINT ( 'NONE', #53098 ) ; +#17593 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#17594 = LINE ( 'NONE', #63100, #50056 ) ; +#17595 = SURFACE_STYLE_FILL_AREA ( #87571 ) ; +#17596 = EDGE_CURVE ( 'NONE', #6603, #100039, #31610, .T. ) ; +#17597 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76598 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73232, #10841, #65055 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17598 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17600 = EDGE_CURVE ( 'NONE', #82972, #39098, #46398, .T. ) ; +#17599 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17601 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17602 = ORIENTED_EDGE ( 'NONE', *, *, #43513, .T. ) ; +#17603 = AXIS2_PLACEMENT_3D ( 'NONE', #14825, #45471, #44489 ) ; +#17604 = LINE ( 'NONE', #88087, #88033 ) ; +#17605 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77376, 'distance_accuracy_value', 'NONE'); +#17607 = FILL_AREA_STYLE_COLOUR ( '', #73917 ) ; +#17606 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25921 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82286, #27668, #18451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17608 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17609 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100649 ), #87751 ) ; +#17610 = ORIENTED_EDGE ( 'NONE', *, *, #10775, .T. ) ; +#17611 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17612 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17613 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.000000000000000000 ) ) ; +#17614 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1155 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87013, #48218, #100674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17615 = LINE ( 'NONE', #80446, #45495 ) ; +#17616 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -11.27000000000000135 ) ) ; +#17617 = SURFACE_SIDE_STYLE ('',( #48811 ) ) ; +#17618 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81233 ) ) ; +#17620 = EDGE_CURVE ( 'NONE', #14910, #90644, #37286, .T. ) ; +#17621 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17622 = ORIENTED_EDGE ( 'NONE', *, *, #8101, .F. ) ; +#17623 = EDGE_LOOP ( 'NONE', ( #14744, #72025, #19360, #38384 ) ) ; +#17624 = STYLED_ITEM ( 'NONE', ( #53146 ), #41741 ) ; +#17625 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.1200000000000003147, 0.4000000000000000222 ) ) ; +#17626 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58443 ) ) ; +#17627 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17628 = CLOSED_SHELL ( 'NONE', ( #16628, #93916, #26162, #10948, #96859, #54746 ) ) ; +#17629 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#17630 = EDGE_LOOP ( 'NONE', ( #13640, #1765, #95970, #38137 ) ) ; +#17631 = EDGE_CURVE ( 'NONE', #9772, #5007, #99451, .T. ) ; +#17632 = SURFACE_STYLE_USAGE ( .BOTH. , #9900 ) ; +#17633 = VERTEX_POINT ( 'NONE', #22433 ) ; +#17634 = EDGE_CURVE ( 'NONE', #48426, #38574, #31107, .T. ) ; +#17635 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999948486, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#17636 = ORIENTED_EDGE ( 'NONE', *, *, #67914, .T. ) ; +#17637 = ORIENTED_EDGE ( 'NONE', *, *, #59311, .T. ) ; +#17638 = CARTESIAN_POINT ( 'NONE', ( 0.9858286694224535074, -1.104443832495993094, 0.8099999999999238920 ) ) ; +#17640 = CARTESIAN_POINT ( 'NONE', ( -0.7996232790101961418, 0.5990488921811000234, 0.8100000000000000533 ) ) ; +#17639 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81261 ), #22547 ) ; +#17642 = PRESENTATION_STYLE_ASSIGNMENT (( #87615 ) ) ; +#17643 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17644 = ORIENTED_EDGE ( 'NONE', *, *, #72649, .F. ) ; +#17645 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100621 ), #38807 ) ; +#17646 = PRESENTATION_STYLE_ASSIGNMENT (( #24355 ) ) ; +#17647 = MANIFOLD_SOLID_BREP ( 'ÊäÈë51', #84477 ) ; +#17648 = LINE ( 'NONE', #87621, #67026 ) ; +#17649 = EDGE_LOOP ( 'NONE', ( #36625, #84981, #52334, #73698 ) ) ; +#17650 = CARTESIAN_POINT ( 'NONE', ( 1.350478891332010267, -1.390055052842650074, 0.8299999999999999600 ) ) ; +#17651 = DIRECTION ( 'NONE', ( 0.000000000000000000, -2.469472024280190074E-26, 1.000000000000000000 ) ) ; +#17652 = ORIENTED_EDGE ( 'NONE', *, *, #6415, .T. ) ; +#17653 = ORIENTED_EDGE ( 'NONE', *, *, #69864, .T. ) ; +#17654 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17656 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#17657 = LINE ( 'NONE', #93234, #15611 ) ; +#17658 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#17659 = PRESENTATION_STYLE_ASSIGNMENT (( #18148 ) ) ; +#17660 = VECTOR ( 'NONE', #99853, 1000.000000000000000 ) ; +#17661 = VECTOR ( 'NONE', #6528, 1000.000000000000000 ) ; +#17663 = EDGE_CURVE ( 'NONE', #12804, #13406, #54623, .T. ) ; +#17662 = DIRECTION ( 'NONE', ( -0.7071071146859688739, -0.7071064476869688420, -0.000000000000000000 ) ) ; +#17664 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17665 = FILL_AREA_STYLE_COLOUR ( '', #35232 ) ; +#17666 = ORIENTED_EDGE ( 'NONE', *, *, #7869, .T. ) ; +#17667 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17669 = PRESENTATION_STYLE_ASSIGNMENT (( #64666 ) ) ; +#17668 = LINE ( 'NONE', #65163, #83173 ) ; +#17670 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.429870129870129958, 0.8299999999999999600 ) ) ; +#17671 = STYLED_ITEM ( 'NONE', ( #40273 ), #56789 ) ; +#17672 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#17673 = SURFACE_STYLE_FILL_AREA ( #2899 ) ; +#17674 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76423 ), #92649 ) ; +#17675 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17676 = PRESENTATION_STYLE_ASSIGNMENT (( #2394 ) ) ; +#17677 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#17678 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#17679 = ORIENTED_EDGE ( 'NONE', *, *, #38427, .F. ) ; +#17680 = SURFACE_SIDE_STYLE ('',( #33027 ) ) ; +#17681 = FILL_AREA_STYLE ('',( #87656 ) ) ; +#17682 = EDGE_CURVE ( 'NONE', #44029, #85080, #18788, .T. ) ; +#17683 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17684 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17685 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17686 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17687 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58515, 'distance_accuracy_value', 'NONE'); +#17688 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#17689 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17690 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17691 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17692 = PRESENTATION_STYLE_ASSIGNMENT (( #42222 ) ) ; +#17693 = STYLED_ITEM ( 'NONE', ( #83736 ), #17534 ) ; +#17695 = VECTOR ( 'NONE', #30371, 1000.000000000000000 ) ; +#17694 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#17696 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#17697 = VECTOR ( 'NONE', #47613, 1000.000000000000000 ) ; +#17698 = FACE_OUTER_BOUND ( 'NONE', #86088, .T. ) ; +#17699 = FILL_AREA_STYLE ('',( #58078 ) ) ; +#17700 = AXIS2_PLACEMENT_3D ( 'NONE', #61588, #30912, #76366 ) ; +#17701 = SURFACE_SIDE_STYLE ('',( #48401 ) ) ; +#17702 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56141, #34177, #65280, #57157 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#17703 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#17704 = SURFACE_STYLE_USAGE ( .BOTH. , #48889 ) ; +#17705 = SURFACE_STYLE_USAGE ( .BOTH. , #88195 ) ; +#17706 = ORIENTED_EDGE ( 'NONE', *, *, #99287, .F. ) ; +#17707 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17708 = LINE ( 'NONE', #95810, #81213 ) ; +#17709 = LINE ( 'NONE', #72347, #18195 ) ; +#17710 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61154, 'distance_accuracy_value', 'NONE'); +#17712 = SURFACE_SIDE_STYLE ('',( #26923 ) ) ; +#17711 = CARTESIAN_POINT ( 'NONE', ( -0.1052747236373319933, -1.219598171061480052, 0.8300000000000002931 ) ) ; +#17713 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4674 ), #12777 ) ; +#17714 = CARTESIAN_POINT ( 'NONE', ( -2.499999999999999556, -3.123820061220085265, 0.000000000000000000 ) ) ; +#17715 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1422 ) ) ; +#17716 = SURFACE_SIDE_STYLE ('',( #18722 ) ) ; +#17717 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17718 = ORIENTED_EDGE ( 'NONE', *, *, #57561, .T. ) ; +#17719 = CARTESIAN_POINT ( 'NONE', ( 10.10135575024997223, 8.852158750249975228, 0.8991599999999999593 ) ) ; +#17721 = EDGE_CURVE ( 'NONE', #54018, #77663, #72940, .T. ) ; +#17720 = SURFACE_STYLE_USAGE ( .BOTH. , #43233 ) ; +#17722 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.523820061220085176, -0.02000000000000000042 ) ) ; +#17723 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2049 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8089, #16813, #9116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17724 = SURFACE_STYLE_FILL_AREA ( #56589 ) ; +#17725 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98160, 'distance_accuracy_value', 'NONE'); +#17726 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14488, 'distance_accuracy_value', 'NONE'); +#17727 = SURFACE_SIDE_STYLE ('',( #72886 ) ) ; +#17728 = EDGE_LOOP ( 'NONE', ( #38268, #2849, #55763, #4626 ) ) ; +#17729 = ORIENTED_EDGE ( 'NONE', *, *, #56516, .T. ) ; +#17730 = SURFACE_STYLE_USAGE ( .BOTH. , #34114 ) ; +#17731 = SURFACE_SIDE_STYLE ('',( #95325 ) ) ; +#17732 = AXIS2_PLACEMENT_3D ( 'NONE', #75864, #60577, #12493 ) ; +#17733 = ORIENTED_EDGE ( 'NONE', *, *, #52083, .T. ) ; +#17734 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65715 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93825, #61262, #99429 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17735 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17736 = VECTOR ( 'NONE', #31051, 1000.000000000000000 ) ; +#17737 = SHAPE_DEFINITION_REPRESENTATION ( #93064, #65081 ) ; +#17738 = LINE ( 'NONE', #63750, #34546 ) ; +#17739 = PRESENTATION_STYLE_ASSIGNMENT (( #95848 ) ) ; +#17741 = EDGE_LOOP ( 'NONE', ( #76269, #34887, #43242, #53254 ) ) ; +#17740 = ORIENTED_EDGE ( 'NONE', *, *, #7094, .T. ) ; +#17742 = ORIENTED_EDGE ( 'NONE', *, *, #90484, .F. ) ; +#17743 = PRESENTATION_STYLE_ASSIGNMENT (( #87718 ) ) ; +#17744 = AXIS2_PLACEMENT_3D ( 'NONE', #14, #18211, #80061 ) ; +#17745 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#17746 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999856 ) ) ; +#17747 = EDGE_LOOP ( 'NONE', ( #71290, #17322, #42154, #38636 ) ) ; +#17748 = STYLED_ITEM ( 'NONE', ( #94207 ), #55950 ) ; +#17749 = MANIFOLD_SOLID_BREP ( 'ÊäÈë13', #99039 ) ; +#17750 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79758 ), #52054 ) ; +#17751 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#17752 = ORIENTED_EDGE ( 'NONE', *, *, #77047, .F. ) ; +#17753 = ORIENTED_EDGE ( 'NONE', *, *, #693, .T. ) ; +#17755 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17754 = LINE ( 'NONE', #32106, #6244 ) ; +#17756 = ORIENTED_EDGE ( 'NONE', *, *, #5321, .T. ) ; +#17757 = VERTEX_POINT ( 'NONE', #40800 ) ; +#17758 = LINE ( 'NONE', #57639, #6914 ) ; +#17759 = VECTOR ( 'NONE', #29479, 1000.000000000000000 ) ; +#17760 = DIRECTION ( 'NONE', ( 2.489536641537530153E-25, -1.494386206516049929E-12, 1.000000000000000000 ) ) ; +#17761 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17762 = CARTESIAN_POINT ( 'NONE', ( 0.1073457792207790085, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#17763 = VECTOR ( 'NONE', #9319, 1000.000000000000000 ) ; +#17765 = EDGE_CURVE ( 'NONE', #80977, #43003, #25487, .T. ) ; +#17764 = SURFACE_STYLE_USAGE ( .BOTH. , #34149 ) ; +#17767 = ORIENTED_EDGE ( 'NONE', *, *, #63865, .F. ) ; +#17766 = FILL_AREA_STYLE ('',( #95871 ) ) ; +#17769 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4733 ) ) ; +#17768 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#17770 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#17771 = FILL_AREA_STYLE_COLOUR ( '', #17282 ) ; +#17772 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17773 = ORIENTED_EDGE ( 'NONE', *, *, #48375, .T. ) ; +#17774 = LINE ( 'NONE', #18781, #22290 ) ; +#17775 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17776 = ORIENTED_EDGE ( 'NONE', *, *, #65598, .F. ) ; +#17777 = EDGE_CURVE ( 'NONE', #43680, #74243, #32636, .T. ) ; +#17778 = ORIENTED_EDGE ( 'NONE', *, *, #95471, .T. ) ; +#17780 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#17779 = FILL_AREA_STYLE ('',( #34165 ) ) ; +#17781 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#17782 = SURFACE_SIDE_STYLE ('',( #19305 ) ) ; +#17783 = CARTESIAN_POINT ( 'NONE', ( -0.3725126731206029884, -1.137476252684360034, 0.8299999999999999600 ) ) ; +#17784 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1492 ), #14473 ) ; +#17785 = ADVANCED_FACE ( 'NONE', ( #9052 ), #27236, .T. ) ; +#17787 = ADVANCED_FACE ( 'NONE', ( #34659 ), #12070, .T. ) ; +#17786 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21883 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90054, #18591, #66085 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17788 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 7.954133000000000564, 0.8648700000000000276 ) ) ; +#17789 = LINE ( 'NONE', #79107, #75278 ) ; +#17790 = ORIENTED_EDGE ( 'NONE', *, *, #54594, .T. ) ; +#17791 = CARTESIAN_POINT ( 'NONE', ( 0.4077210354193729902, -1.190630982187130149, 0.8100000000000000533 ) ) ; +#17792 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17793 = ORIENTED_EDGE ( 'NONE', *, *, #65533, .F. ) ; +#17794 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#17795 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, -3.099999999999969891, 0.000000000000000000 ) ) ; +#17797 = EDGE_CURVE ( 'NONE', #13965, #98006, #58657, .T. ) ; +#17796 = STYLED_ITEM ( 'NONE', ( #7474 ), #44240 ) ; +#17798 = ADVANCED_FACE ( 'NONE', ( #50494 ), #19819, .F. ) ; +#17799 = FILL_AREA_STYLE_COLOUR ( '', #19052 ) ; +#17800 = SURFACE_STYLE_FILL_AREA ( #95901 ) ; +#17801 = FILL_AREA_STYLE_COLOUR ( '', #20943 ) ; +#17803 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#17802 = LINE ( 'NONE', #33148, #44666 ) ; +#17804 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#17805 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#17806 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.792553465592259094E-15, 0.000000000000000000 ) ) ; +#17807 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17808 = SURFACE_STYLE_USAGE ( .BOTH. , #70950 ) ; +#17809 = EDGE_CURVE ( 'NONE', #85797, #89063, #35671, .T. ) ; +#17810 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#17811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17812 = PRESENTATION_STYLE_ASSIGNMENT (( #34190 ) ) ; +#17813 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68679 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79407, #73750, #80416 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17814 = CARTESIAN_POINT ( 'NONE', ( -0.8193368432721279682, 0.5992714337669160507, 0.8299999999999999600 ) ) ; +#17815 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#17816 = PRESENTATION_STYLE_ASSIGNMENT (( #95915 ) ) ; +#17817 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83073 ) ) ; +#17818 = VECTOR ( 'NONE', #758, 1000.000000000000000 ) ; +#17819 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#17820 = LINE ( 'NONE', #57692, #15723 ) ; +#17821 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#17822 = PRESENTATION_STYLE_ASSIGNMENT (( #25522 ) ) ; +#17823 = LINE ( 'NONE', #88795, #73046 ) ; +#17824 = AXIS2_PLACEMENT_3D ( 'NONE', #39372, #16875, #2111 ) ; +#17825 = MANIFOLD_SOLID_BREP ( 'ÊäÈë52', #32171 ) ; +#17826 = STYLED_ITEM ( 'NONE', ( #59966 ), #92075 ) ; +#17827 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21477, 'distance_accuracy_value', 'NONE'); +#17828 = ORIENTED_EDGE ( 'NONE', *, *, #1329, .T. ) ; +#17829 = SURFACE_SIDE_STYLE ('',( #81670 ) ) ; +#17830 = SURFACE_SIDE_STYLE ('',( #11101 ) ) ; +#17831 = ORIENTED_EDGE ( 'NONE', *, *, #50503, .T. ) ; +#17832 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17833 = AXIS2_PLACEMENT_3D ( 'NONE', #73902, #25441, #2947 ) ; +#17834 = DIRECTION ( 'NONE', ( 0.7071090539100437500, -0.7071045084557464611, 0.000000000000000000 ) ) ; +#17835 = SURFACE_SIDE_STYLE ('',( #34212 ) ) ; +#17836 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.099999999999999867, 0.8299999999999999600 ) ) ; +#17837 = AXIS2_PLACEMENT_3D ( 'NONE', #28260, #98119, #21096 ) ; +#17838 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17839 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.09999999999999996392, -0.02000000000000000042 ) ) ; +#17840 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14597 ), #24454 ) ; +#17841 = ORIENTED_EDGE ( 'NONE', *, *, #26005, .F. ) ; +#17842 = ORIENTED_EDGE ( 'NONE', *, *, #82929, .F. ) ; +#17843 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11213 ), #52213 ) ; +#17844 = EDGE_CURVE ( 'NONE', #99540, #41527, #3992, .T. ) ; +#17846 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17845 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#17847 = FILL_AREA_STYLE_COLOUR ( '', #22798 ) ; +#17848 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#17849 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17850 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17851 = VECTOR ( 'NONE', #8538, 1000.000000000000000 ) ; +#17852 = EDGE_CURVE ( 'NONE', #52968, #98494, #21815, .T. ) ; +#17853 = VERTEX_POINT ( 'NONE', #335 ) ; +#17854 = SURFACE_STYLE_FILL_AREA ( #11626 ) ; +#17855 = FILL_AREA_STYLE_COLOUR ( '', #98242 ) ; +#17856 = ORIENTED_EDGE ( 'NONE', *, *, #85534, .F. ) ; +#17857 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17858 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17859 = EDGE_LOOP ( 'NONE', ( #37946, #65075, #25974, #55969 ) ) ; +#17860 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17861 = SURFACE_STYLE_USAGE ( .BOTH. , #41880 ) ; +#17862 = SURFACE_STYLE_USAGE ( .BOTH. , #18358 ) ; +#17863 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28067 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80288, #17952, #81803 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#17864 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17865 = CARTESIAN_POINT ( 'NONE', ( -1.089702767725039934, -0.9656714926165439472, 0.8100000000000000533 ) ) ; +#17866 = PRESENTATION_STYLE_ASSIGNMENT (( #72503 ) ) ; +#17867 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17869 = ORIENTED_EDGE ( 'NONE', *, *, #22054, .T. ) ; +#17868 = ORIENTED_EDGE ( 'NONE', *, *, #94534, .T. ) ; +#17870 = LINE ( 'NONE', #87837, #73128 ) ; +#17871 = STYLED_ITEM ( 'NONE', ( #12511 ), #44415 ) ; +#17872 = ORIENTED_EDGE ( 'NONE', *, *, #14227, .T. ) ; +#17873 = FILL_AREA_STYLE_COLOUR ( '', #29672 ) ; +#17875 = SURFACE_STYLE_USAGE ( .BOTH. , #87843 ) ; +#17874 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#17876 = ORIENTED_EDGE ( 'NONE', *, *, #77464, .T. ) ; +#17877 = ORIENTED_EDGE ( 'NONE', *, *, #47189, .T. ) ; +#17878 = FACE_OUTER_BOUND ( 'NONE', #39121, .T. ) ; +#17879 = PLANE ( 'NONE', #38244 ) ; +#17880 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17881 = SURFACE_STYLE_USAGE ( .BOTH. , #95479 ) ; +#17882 = SURFACE_STYLE_FILL_AREA ( #40400 ) ; +#17883 = ORIENTED_EDGE ( 'NONE', *, *, #80787, .F. ) ; +#17884 = VERTEX_POINT ( 'NONE', #93230 ) ; +#17885 = DIRECTION ( 'NONE', ( -0.7071067811865493491, -0.7071067811865455743, 0.000000000000000000 ) ) ; +#17886 = EDGE_LOOP ( 'NONE', ( #1724, #93461, #73550, #73071 ) ) ; +#17887 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#17888 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9659 ), #1600 ) ; +#17889 = VECTOR ( 'NONE', #69877, 1000.000000000000000 ) ; +#17890 = VERTEX_POINT ( 'NONE', #6436 ) ; +#17891 = ORIENTED_EDGE ( 'NONE', *, *, #12645, .T. ) ; +#17892 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#17893 = EDGE_LOOP ( 'NONE', ( #26588, #76640, #84444, #20095 ) ) ; +#17894 = VECTOR ( 'NONE', #72261, 1000.000000000000000 ) ; +#17895 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#17896 = FILL_AREA_STYLE_COLOUR ( '', #15890 ) ; +#17897 = CARTESIAN_POINT ( 'NONE', ( 0.1238200612200860418, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#17898 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.900000000000000133, 1.009450051515179092E-78 ) ) ; +#17899 = FILL_AREA_STYLE ('',( #87871 ) ) ; +#17901 = FILL_AREA_STYLE_COLOUR ( '', #7376 ) ; +#17900 = CARTESIAN_POINT ( 'NONE', ( -0.4575742935596588401, -1.148122757146818884, 0.8299999999999998490 ) ) ; +#17902 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#17903 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17904 = ORIENTED_EDGE ( 'NONE', *, *, #18320, .F. ) ; +#17905 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#17906 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#17907 = CARTESIAN_POINT ( 'NONE', ( -1.069701591823909892, -0.8955552045491339541, 0.8300000000000000711 ) ) ; +#17908 = ORIENTED_EDGE ( 'NONE', *, *, #14806, .T. ) ; +#17909 = CARTESIAN_POINT ( 'NONE', ( 10.49026475025008764, 7.544011249749912551, 0.8991599999999999593 ) ) ; +#17910 = VECTOR ( 'NONE', #78079, 1000.000000000000000 ) ; +#17911 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#17912 = EDGE_CURVE ( 'NONE', #6840, #16540, #68261, .T. ) ; +#17913 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#17914 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6892893218813450629, -0.9757359312880714564 ) ) ; +#17915 = MANIFOLD_SOLID_BREP ( 'ÊäÈë181', #17628 ) ; +#17916 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17917 = STYLED_ITEM ( 'NONE', ( #62198 ), #51299 ) ; +#17918 = PLANE ( 'NONE', #45846 ) ; +#17919 = PRESENTATION_STYLE_ASSIGNMENT (( #43819 ) ) ; +#17920 = VECTOR ( 'NONE', #73102, 1000.000000000000000 ) ; +#17921 = EDGE_CURVE ( 'NONE', #88447, #36185, #53478, .T. ) ; +#17922 = VERTEX_POINT ( 'NONE', #92730 ) ; +#17923 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#17924 = FILL_AREA_STYLE_COLOUR ( '', #77133 ) ; +#17925 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#17926 = LINE ( 'NONE', #32779, #92002 ) ; +#17927 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17928 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61185, 'distance_accuracy_value', 'NONE'); +#17929 = EDGE_LOOP ( 'NONE', ( #37960, #35484, #82836, #30525, #66616, #20157 ) ) ; +#17930 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17931 = SURFACE_STYLE_USAGE ( .BOTH. , #3651 ) ; +#17932 = FACE_OUTER_BOUND ( 'NONE', #83203, .T. ) ; +#17933 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#17934 = CARTESIAN_POINT ( 'NONE', ( 0.5300000000829642177, 0.2500000001077753442, 5.131455198788644142E-17 ) ) ; +#17935 = FILL_AREA_STYLE ('',( #87911 ) ) ; +#17936 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17937 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#17938 = FILL_AREA_STYLE_COLOUR ( '', #97952 ) ; +#17939 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#17940 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #60359, #14306 ), + ( #70479, #30655 ), + ( #92924, #54699 ), + ( #23543, #39337 ), + ( #69976, #29 ), + ( #85298, #30161 ), + ( #62866, #68464 ), + ( #23043, #53176 ), + ( #78166, #45459 ), + ( #31191, #62354 ), + ( #38360, #84794 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.1253844121579359983, 0.2490499212940600060, 0.3727373688245280148, 0.4983139852987960028, 0.6236767560303250191, 0.7468439467830330081, 0.8707651621907409600, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#17941 = LINE ( 'NONE', #25647, #73695 ) ; +#17942 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58760 ) ) ; +#17944 = EDGE_CURVE ( 'NONE', #45477, #99864, #15629, .T. ) ; +#17943 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17945 = PRESENTATION_STYLE_ASSIGNMENT (( #70580 ) ) ; +#17946 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.500000000000000000, 1.121611168366946904E-78 ) ) ; +#17947 = ORIENTED_EDGE ( 'NONE', *, *, #39369, .T. ) ; +#17948 = PLANE ( 'NONE', #67703 ) ; +#17949 = EDGE_LOOP ( 'NONE', ( #70115, #12153, #67081, #85097 ) ) ; +#17950 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#17951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87850, 'distance_accuracy_value', 'NONE'); +#17952 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17953 = PRESENTATION_STYLE_ASSIGNMENT (( #48131 ) ) ; +#17954 = VECTOR ( 'NONE', #76763, 1000.000000000000000 ) ; +#17955 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 10.37243800000000071, 0.8648700000000000276 ) ) ; +#17956 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#17957 = SURFACE_STYLE_FILL_AREA ( #55802 ) ; +#17958 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.266666666666647068, 0.000000000000000000 ) ) ; +#17959 = SURFACE_STYLE_FILL_AREA ( #57841 ) ; +#17960 = LINE ( 'NONE', #87933, #61937 ) ; +#17961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55485 ), #13024 ) ; +#17962 = ADVANCED_FACE ( 'NONE', ( #54493 ), #77436, .T. ) ; +#17963 = ORIENTED_EDGE ( 'NONE', *, *, #63865, .T. ) ; +#17964 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#17965 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#17966 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.449999999999999956, -11.41999999999999993 ) ) ; +#17967 = ORIENTED_EDGE ( 'NONE', *, *, #55880, .F. ) ; +#17968 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17970 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#17969 = AXIS2_PLACEMENT_3D ( 'NONE', #90807, #97903, #5482 ) ; +#17971 = LINE ( 'NONE', #49669, #61423 ) ; +#17972 = VECTOR ( 'NONE', #76340, 1000.000000000000000 ) ; +#17973 = ORIENTED_EDGE ( 'NONE', *, *, #6129, .F. ) ; +#17974 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#17975 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#17976 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84820 ), #9759 ) ; +#17977 = ORIENTED_EDGE ( 'NONE', *, *, #86276, .F. ) ; +#17978 = AXIS2_PLACEMENT_3D ( 'NONE', #6412, #46757, #100769 ) ; +#17979 = MANIFOLD_SOLID_BREP ( 'ÊäÈë155', #61557 ) ; +#17980 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#17981 = ORIENTED_EDGE ( 'NONE', *, *, #40803, .F. ) ; +#17983 = EDGE_CURVE ( 'NONE', #52597, #53045, #47820, .T. ) ; +#17982 = VERTEX_POINT ( 'NONE', #80483 ) ; +#17984 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#17985 = SURFACE_STYLE_FILL_AREA ( #87966 ) ; +#17986 = FILL_AREA_STYLE ('',( #97106 ) ) ; +#17987 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#17988 = STYLED_ITEM ( 'NONE', ( #17195 ), #51387 ) ; +#17989 = LINE ( 'NONE', #98063, #58249 ) ; +#17990 = VERTEX_POINT ( 'NONE', #34033 ) ; +#17992 = ORIENTED_EDGE ( 'NONE', *, *, #91861, .T. ) ; +#17991 = EDGE_LOOP ( 'NONE', ( #26335, #53219, #29678, #64114 ) ) ; +#17993 = EDGE_CURVE ( 'NONE', #48036, #62758, #78957, .T. ) ; +#17994 = VERTEX_POINT ( 'NONE', #93726 ) ; +#17995 = AXIS2_PLACEMENT_3D ( 'NONE', #15029, #38567, #69687 ) ; +#17996 = FACE_OUTER_BOUND ( 'NONE', #17649, .T. ) ; +#17997 = ORIENTED_EDGE ( 'NONE', *, *, #388, .T. ) ; +#17999 = ORIENTED_EDGE ( 'NONE', *, *, #64419, .T. ) ; +#17998 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 1.100000000000000311, 0.000000000000000000 ) ) ; +#18000 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18001 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18002 = ORIENTED_EDGE ( 'NONE', *, *, #65516, .T. ) ; +#18003 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, -1.149999999999999911 ) ) ; +#18004 = CARTESIAN_POINT ( 'NONE', ( 1.784639205958740371, -1.415447185383410078, 0.8099999999999997202 ) ) ; +#18005 = VERTEX_POINT ( 'NONE', #18143 ) ; +#18006 = EDGE_CURVE ( 'NONE', #42643, #67209, #8415, .T. ) ; +#18007 = PRESENTATION_STYLE_ASSIGNMENT (( #39503 ) ) ; +#18008 = ADVANCED_FACE ( 'NONE', ( #95245 ), #24367, .T. ) ; +#18009 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18010 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#18011 = SURFACE_STYLE_FILL_AREA ( #94096 ) ; +#18012 = EDGE_LOOP ( 'NONE', ( #88372, #26986, #96752, #8636 ) ) ; +#18013 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.5000000000000000000, -0.02000000000002100098 ) ) ; +#18014 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18015 = STYLED_ITEM ( 'NONE', ( #67659 ), #95420 ) ; +#18017 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.289444213855800265E-17, -0.8499999999999999778 ) ) ; +#18016 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#18018 = FILL_AREA_STYLE ('',( #10293 ) ) ; +#18019 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18020 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18021 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93173 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93263, #7943, #68783 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18022 = STYLED_ITEM ( 'NONE', ( #37038 ), #94486 ) ; +#18023 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18024 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68540 ) ) ; +#18025 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18026 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18027 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#18028 = VECTOR ( 'NONE', #86587, 1000.000000000000114 ) ; +#18029 = CARTESIAN_POINT ( 'NONE', ( -0.9621292638465409608, -0.9747981717974689708, 0.8100000000000000533 ) ) ; +#18030 = STYLED_ITEM ( 'NONE', ( #96179 ), #65654 ) ; +#18031 = ORIENTED_EDGE ( 'NONE', *, *, #62544, .F. ) ; +#18032 = FACE_OUTER_BOUND ( 'NONE', #89886, .T. ) ; +#18033 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18034 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18035 = PRESENTATION_STYLE_ASSIGNMENT (( #13742 ) ) ; +#18036 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18037 = ORIENTED_EDGE ( 'NONE', *, *, #96536, .F. ) ; +#18038 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18039 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89790 ), #5000 ) ; +#18040 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#18041 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11298, 'distance_accuracy_value', 'NONE'); +#18042 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18043 = CARTESIAN_POINT ( 'NONE', ( -0.2409735724455049910, -1.328064047174219997, 0.8299999999999999600 ) ) ; +#18044 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8100000000000000533 ) ) ; +#18045 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.869314090631718434E-16, 0.000000000000000000 ) ) ; +#18046 = LINE ( 'NONE', #9834, #39506 ) ; +#18047 = ORIENTED_EDGE ( 'NONE', *, *, #30864, .F. ) ; +#18048 = FACE_OUTER_BOUND ( 'NONE', #64748, .T. ) ; +#18049 = LINE ( 'NONE', #95662, #28263 ) ; +#18050 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18051 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#18052 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#18053 = LINE ( 'NONE', #49245, #37180 ) ; +#18054 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18055 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#18056 = VECTOR ( 'NONE', #34458, 1000.000000000000000 ) ; +#18057 = EDGE_CURVE ( 'NONE', #47153, #5274, #95756, .T. ) ; +#18058 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#18059 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#18060 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.099999999999999867, 4.486444673467788097E-79 ) ) ; +#18061 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, 0.000000000000000000 ) ) ; +#18062 = EDGE_CURVE ( 'NONE', #44158, #20515, #89753, .T. ) ; +#18063 = SURFACE_SIDE_STYLE ('',( #76348 ) ) ; +#18064 = SURFACE_STYLE_FILL_AREA ( #73737 ) ; +#18065 = LINE ( 'NONE', #80407, #12753 ) ; +#18066 = ORIENTED_EDGE ( 'NONE', *, *, #17765, .T. ) ; +#18067 = VERTEX_POINT ( 'NONE', #12447 ) ; +#18068 = PRESENTATION_STYLE_ASSIGNMENT (( #88068 ) ) ; +#18069 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2850000000000000311, 0.1458578643762690474 ) ) ; +#18070 = CARTESIAN_POINT ( 'NONE', ( 1.874899521751800080, -1.024811280222130083, 0.8100000000000000533 ) ) ; +#18071 = CARTESIAN_POINT ( 'NONE', ( 11.38829012487495618, 7.565224875125044157, 0.8648700000000000276 ) ) ; +#18072 = LINE ( 'NONE', #56957, #35857 ) ; +#18073 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#18074 = EDGE_CURVE ( 'NONE', #21432, #37825, #3407, .T. ) ; +#18075 = VERTEX_POINT ( 'NONE', #81998 ) ; +#18076 = FACE_OUTER_BOUND ( 'NONE', #55704, .T. ) ; +#18077 = MANIFOLD_SOLID_BREP ( 'ÊäÈë174', #40490 ) ; +#18078 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18079 = SURFACE_SIDE_STYLE ('',( #25802 ) ) ; +#18080 = VECTOR ( 'NONE', #98654, 1000.000000000000000 ) ; +#18081 = FILL_AREA_STYLE ('',( #79928 ) ) ; +#18082 = EDGE_LOOP ( 'NONE', ( #51744, #27678, #40476, #83852, #39404, #38494 ) ) ; +#18083 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#18084 = SURFACE_STYLE_USAGE ( .BOTH. , #34478 ) ; +#18085 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18086 = VECTOR ( 'NONE', #29272, 1000.000000000000000 ) ; +#18087 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#18088 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#18089 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#18090 = ORIENTED_EDGE ( 'NONE', *, *, #5070, .T. ) ; +#18091 = CARTESIAN_POINT ( 'NONE', ( 11.95397624975002770, 5.528756750249976371, 0.8648700000000000276 ) ) ; +#18092 = VECTOR ( 'NONE', #41935, 1000.000000000000000 ) ; +#18093 = LINE ( 'NONE', #64597, #70071 ) ; +#18094 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83097, 'distance_accuracy_value', 'NONE'); +#18095 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100213 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99592, #74716, #52251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18096 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18097 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#18098 = ORIENTED_EDGE ( 'NONE', *, *, #55138, .T. ) ; +#18099 = FILL_AREA_STYLE ('',( #79434 ) ) ; +#18100 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#18101 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27672, #58830, #58328 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18102 = LINE ( 'NONE', #49299, #64690 ) ; +#18103 = SURFACE_SIDE_STYLE ('',( #2831 ) ) ; +#18104 = EDGE_CURVE ( 'NONE', #5550, #47399, #89645, .T. ) ; +#18105 = STYLED_ITEM ( 'NONE', ( #76095 ), #65279 ) ; +#18106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81735 ), #8290 ) ; +#18107 = VECTOR ( 'NONE', #18893, 1000.000000000000000 ) ; +#18108 = EDGE_LOOP ( 'NONE', ( #98341, #47936, #46739, #82911 ) ) ; +#18110 = ORIENTED_EDGE ( 'NONE', *, *, #26188, .F. ) ; +#18109 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#18111 = EDGE_CURVE ( 'NONE', #62500, #79973, #90646, .T. ) ; +#18112 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17772, 'distance_accuracy_value', 'NONE'); +#18113 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#18115 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#18114 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18116 = LINE ( 'NONE', #1322, #83920 ) ; +#18117 = SURFACE_STYLE_USAGE ( .BOTH. , #88118 ) ; +#18118 = ORIENTED_EDGE ( 'NONE', *, *, #8244, .T. ) ; +#18119 = ADVANCED_FACE ( 'NONE', ( #26871 ), #36040, .T. ) ; +#18120 = SURFACE_STYLE_FILL_AREA ( #33503 ) ; +#18121 = LINE ( 'NONE', #55988, #84892 ) ; +#18122 = ADVANCED_FACE ( 'NONE', ( #11440 ), #58541, .T. ) ; +#18123 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#18124 = VECTOR ( 'NONE', #65690, 1000.000000000000000 ) ; +#18125 = ORIENTED_EDGE ( 'NONE', *, *, #72684, .T. ) ; +#18126 = EDGE_CURVE ( 'NONE', #51201, #13305, #49041, .T. ) ; +#18128 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#18127 = SURFACE_STYLE_FILL_AREA ( #57005 ) ; +#18129 = ORIENTED_EDGE ( 'NONE', *, *, #58990, .F. ) ; +#18130 = ORIENTED_EDGE ( 'NONE', *, *, #28953, .F. ) ; +#18131 = SURFACE_STYLE_USAGE ( .BOTH. , #19156 ) ; +#18132 = PRESENTATION_STYLE_ASSIGNMENT (( #48832 ) ) ; +#18133 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18135 = VERTEX_POINT ( 'NONE', #21188 ) ; +#18134 = STYLED_ITEM ( 'NONE', ( #31948 ), #45434 ) ; +#18136 = ADVANCED_FACE ( 'NONE', ( #37537 ), #69638, .T. ) ; +#18137 = FILL_AREA_STYLE_COLOUR ( '', #3425 ) ; +#18138 = ORIENTED_EDGE ( 'NONE', *, *, #13707, .T. ) ; +#18139 = CARTESIAN_POINT ( 'NONE', ( 1.334872846471060193, -1.409018172687890091, 0.8100000000000000533 ) ) ; +#18140 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18141 = ORIENTED_EDGE ( 'NONE', *, *, #36112, .T. ) ; +#18143 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#18142 = SURFACE_STYLE_FILL_AREA ( #88142 ) ; +#18144 = CARTESIAN_POINT ( 'NONE', ( -1.311685777689840293, -1.173235213159260049, 0.8100000000000000533 ) ) ; +#18145 = ADVANCED_FACE ( 'NONE', ( #91624 ), #91141, .T. ) ; +#18146 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71984 ) ) ; +#18147 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100224 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20009, #44471, #36353 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18148 = SURFACE_STYLE_USAGE ( .BOTH. , #71820 ) ; +#18149 = LINE ( 'NONE', #74330, #70652 ) ; +#18150 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#18151 = LINE ( 'NONE', #72827, #29096 ) ; +#18152 = STYLED_ITEM ( 'NONE', ( #14116 ), #86743 ) ; +#18153 = CARTESIAN_POINT ( 'NONE', ( 1.275362369208429936, -0.9706035140527151661, 0.8100000000000000533 ) ) ; +#18154 = ADVANCED_FACE ( 'NONE', ( #7785 ), #86499, .F. ) ; +#18155 = VERTEX_POINT ( 'NONE', #16513 ) ; +#18156 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#18157 = ADVANCED_FACE ( 'NONE', ( #79863 ), #25739, .T. ) ; +#18158 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#18159 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18161 = PLANE ( 'NONE', #64434 ) ; +#18160 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65412 ), #78531 ) ; +#18162 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15186, 'distance_accuracy_value', 'NONE'); +#18163 = VECTOR ( 'NONE', #76825, 1000.000000000000000 ) ; +#18164 = PLANE ( 'NONE', #80515 ) ; +#18165 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18166 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18167 = FACE_OUTER_BOUND ( 'NONE', #10258, .T. ) ; +#18168 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18169 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #53145 ) ) ; +#18170 = ORIENTED_EDGE ( 'NONE', *, *, #48178, .T. ) ; +#18171 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18172 = SURFACE_STYLE_USAGE ( .BOTH. , #50403 ) ; +#18173 = FILL_AREA_STYLE_COLOUR ( '', #60785 ) ; +#18174 = FILL_AREA_STYLE ('',( #41209 ) ) ; +#18175 = SURFACE_SIDE_STYLE ('',( #88167 ) ) ; +#18176 = SURFACE_STYLE_FILL_AREA ( #88168 ) ; +#18177 = SURFACE_STYLE_FILL_AREA ( #11463 ) ; +#18178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19887 ) ) ; +#18179 = CARTESIAN_POINT ( 'NONE', ( 8.277020750249976189, 1.851801249750025802, 0.8991599999999999593 ) ) ; +#18180 = PRESENTATION_STYLE_ASSIGNMENT (( #81552 ) ) ; +#18181 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18182 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18183 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18184 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18185 = EDGE_CURVE ( 'NONE', #28217, #77835, #63040, .T. ) ; +#18186 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#18187 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#18188 = VECTOR ( 'NONE', #86574, 1000.000000000000000 ) ; +#18189 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853420540, 1.377634075926970070, 0.8100000000000000533 ) ) ; +#18190 = CIRCLE ( 'NONE', #81800, 0.6999999999999999556 ) ; +#18191 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18192 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18193 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 6.695483000000000295, 0.8648700000000000276 ) ) ; +#18194 = DIRECTION ( 'NONE', ( 9.346570452461240360E-17, -1.000000000000000000, 5.551115123125790098E-17 ) ) ; +#18195 = VECTOR ( 'NONE', #57576, 999.9999999999998863 ) ; +#18196 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18197 = EDGE_CURVE ( 'NONE', #4091, #19242, #31357, .T. ) ; +#18198 = ORIENTED_EDGE ( 'NONE', *, *, #10489, .F. ) ; +#18199 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#18200 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18201 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18202 = ADVANCED_FACE ( 'NONE', ( #54876 ), #8296, .T. ) ; +#18203 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#18204 = STYLED_ITEM ( 'NONE', ( #61113 ), #46451 ) ; +#18205 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#18206 = LINE ( 'NONE', #71878, #64685 ) ; +#18207 = ORIENTED_EDGE ( 'NONE', *, *, #65516, .F. ) ; +#18208 = EDGE_CURVE ( 'NONE', #19759, #23933, #20562, .T. ) ; +#18209 = AXIS2_PLACEMENT_3D ( 'NONE', #79296, #47649, #71128 ) ; +#18210 = FILL_AREA_STYLE_COLOUR ( '', #41566 ) ; +#18211 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18212 = CARTESIAN_POINT ( 'NONE', ( 7.386065916749879889, 4.849934916749958802, 0.8991599999999999593 ) ) ; +#18213 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18214 = FACE_OUTER_BOUND ( 'NONE', #33625, .T. ) ; +#18215 = VERTEX_POINT ( 'NONE', #90513 ) ; +#18216 = ORIENTED_EDGE ( 'NONE', *, *, #75779, .F. ) ; +#18217 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1936 ) ) ; +#18218 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 8.569316000000000599, 0.8648700000000000276 ) ) ; +#18219 = ORIENTED_EDGE ( 'NONE', *, *, #93941, .F. ) ; +#18220 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18221 = PLANE ( 'NONE', #97163 ) ; +#18222 = FILL_AREA_STYLE ('',( #42264 ) ) ; +#18223 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18224 = SURFACE_STYLE_USAGE ( .BOTH. , #2452 ) ; +#18225 = EDGE_CURVE ( 'NONE', #68754, #64741, #72690, .T. ) ; +#18226 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93207 ), #13290 ) ; +#18227 = VECTOR ( 'NONE', #63823, 1000.000000000000000 ) ; +#18228 = STYLED_ITEM ( 'NONE', ( #6362 ), #96211 ) ; +#18229 = SHAPE_DEFINITION_REPRESENTATION ( #40182, #75506 ) ; +#18230 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#18231 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18233 = ORIENTED_EDGE ( 'NONE', *, *, #1360, .F. ) ; +#18232 = ORIENTED_EDGE ( 'NONE', *, *, #93599, .T. ) ; +#18234 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73301 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76916, #38125, #80454 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18235 = ORIENTED_EDGE ( 'NONE', *, *, #49319, .T. ) ; +#18236 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55753 ) ) ; +#18237 = VERTEX_POINT ( 'NONE', #65033 ) ; +#18238 = FACE_OUTER_BOUND ( 'NONE', #60204, .T. ) ; +#18239 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3535, 'distance_accuracy_value', 'NONE'); +#18240 = AXIS2_PLACEMENT_3D ( 'NONE', #14082, #30414, #45235 ) ; +#18241 = CARTESIAN_POINT ( 'NONE', ( 1.897517923509739912, -1.370875895369189967, 0.8299999999999999600 ) ) ; +#18242 = CARTESIAN_POINT ( 'NONE', ( 1.408334268560540004, -1.010972591757870021, 0.8299999999999999600 ) ) ; +#18243 = ORIENTED_EDGE ( 'NONE', *, *, #64044, .T. ) ; +#18244 = STYLED_ITEM ( 'NONE', ( #96510 ), #7668 ) ; +#18245 = MANIFOLD_SOLID_BREP ( 'ÊäÈë40', #79485 ) ; +#18246 = ADVANCED_FACE ( 'NONE', ( #80366 ), #58418, .T. ) ; +#18247 = SURFACE_STYLE_FILL_AREA ( #1964 ) ; +#18248 = SURFACE_STYLE_USAGE ( .BOTH. , #65242 ) ; +#18249 = EDGE_CURVE ( 'NONE', #54887, #12578, #64876, .T. ) ; +#18250 = ORIENTED_EDGE ( 'NONE', *, *, #67690, .T. ) ; +#18251 = PLANE ( 'NONE', #64515 ) ; +#18252 = VECTOR ( 'NONE', #95813, 1000.000000000000114 ) ; +#18253 = ORIENTED_EDGE ( 'NONE', *, *, #48828, .F. ) ; +#18255 = PLANE ( 'NONE', #33209 ) ; +#18254 = LINE ( 'NONE', #10025, #11107 ) ; +#18256 = ORIENTED_EDGE ( 'NONE', *, *, #48285, .T. ) ; +#18257 = VERTEX_POINT ( 'NONE', #34418 ) ; +#18258 = AXIS2_PLACEMENT_3D ( 'NONE', #34968, #3794, #42608 ) ; +#18259 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18260 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18261 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18263 = ORIENTED_EDGE ( 'NONE', *, *, #21451, .F. ) ; +#18262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18264 = SURFACE_STYLE_USAGE ( .BOTH. , #48957 ) ; +#18265 = EDGE_LOOP ( 'NONE', ( #61367, #62874, #10213, #21406 ) ) ; +#18266 = CARTESIAN_POINT ( 'NONE', ( -0.2677310921211660810, -0.9808836469697851390, 0.8299999999999999600 ) ) ; +#18267 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18268 = ORIENTED_EDGE ( 'NONE', *, *, #83869, .T. ) ; +#18270 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18269 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#18271 = CARTESIAN_POINT ( 'NONE', ( 0.04300883857482180189, -1.212495751768609908, 0.8299999999999999600 ) ) ; +#18272 = ORIENTED_EDGE ( 'NONE', *, *, #87764, .T. ) ; +#18273 = ORIENTED_EDGE ( 'NONE', *, *, #66877, .T. ) ; +#18274 = SURFACE_SIDE_STYLE ('',( #57141 ) ) ; +#18275 = EDGE_CURVE ( 'NONE', #37766, #78634, #40470, .T. ) ; +#18276 = AXIS2_PLACEMENT_3D ( 'NONE', #77849, #7811, #90797 ) ; +#18277 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18279 = STYLED_ITEM ( 'NONE', ( #21046 ), #46635 ) ; +#18278 = LINE ( 'NONE', #26492, #49466 ) ; +#18280 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18281 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18282 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25652, 'distance_accuracy_value', 'NONE'); +#18283 = ADVANCED_FACE ( 'NONE', ( #37906 ), #30940, .F. ) ; +#18284 = ORIENTED_EDGE ( 'NONE', *, *, #76368, .T. ) ; +#18285 = VERTEX_POINT ( 'NONE', #32268 ) ; +#18286 = EDGE_CURVE ( 'NONE', #88220, #3470, #47574, .T. ) ; +#18287 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47685 ) ) ; +#18288 = VECTOR ( 'NONE', #76148, 1000.000000000000000 ) ; +#18289 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#18290 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#18291 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18292 = DIRECTION ( 'NONE', ( -0.7071067811865484609, 0.7071067811865465735, 0.000000000000000000 ) ) ; +#18293 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34960 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16933, #48110, #39424 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18294 = LINE ( 'NONE', #81141, #86204 ) ; +#18295 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18296 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18297 = CARTESIAN_POINT ( 'NONE', ( 1.662784497387987726, -1.164919038798193585, 0.8233333333333332504 ) ) ; +#18298 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#18300 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63737 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1773, #17049, #32902 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18299 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 9.263423361716145940E-17, 0.6500000000000001332 ) ) ; +#18301 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#18302 = CARTESIAN_POINT ( 'NONE', ( -1.293366770995789894, -1.052467830684129968, 0.8299999999999998490 ) ) ; +#18303 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8648700000000000276 ) ) ; +#18304 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8099999999999111244 ) ) ; +#18306 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#18305 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98679 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91995, #59410, #50730 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18307 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41863, #40359, #80682, #71488 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#18308 = STYLED_ITEM ( 'NONE', ( #32940 ), #96290 ) ; +#18309 = EDGE_CURVE ( 'NONE', #48947, #95335, #63629, .T. ) ; +#18310 = CARTESIAN_POINT ( 'NONE', ( -1.970710678118652970, 1.529289321881341479, 0.000000000000000000 ) ) ; +#18311 = FILL_AREA_STYLE ('',( #87785 ) ) ; +#18312 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18313 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18314 = AXIS2_PLACEMENT_3D ( 'NONE', #96409, #12095, #74481 ) ; +#18315 = AXIS2_PLACEMENT_3D ( 'NONE', #20653, #67116, #36013 ) ; +#18316 = ORIENTED_EDGE ( 'NONE', *, *, #55890, .T. ) ; +#18318 = CARTESIAN_POINT ( 'NONE', ( 1.688788655318780085, -0.9001377335631759458, 0.8299999999999999600 ) ) ; +#18317 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56298, #71084, #70562, #69542, #77728, #31259, #47084, #93513, #100572, #24654, #55776, #54260, #85383, #86401, #78726, #46569, #30741, #62430, #16408 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.054321695876134369E-05, 3.977443830994896641E-05, 5.802765165674170954E-05, 7.538725950258324203E-05, 9.210694894944976968E-05, 0.0001084057593000208649, 0.0001242682963548059536, 0.0001400066046754130944, 0.0001558427716450202095, 0.0001718928714940627471, 0.0001884659511934544786, 0.0002055442570027103146, 0.0002230869087387579339, 0.0002410848313338994503, 0.0002596240640649384872, 0.0002786931581751934798 ), + .UNSPECIFIED. ) ; +#18320 = EDGE_CURVE ( 'NONE', #43289, #70495, #46546, .T. ) ; +#18319 = PRESENTATION_STYLE_ASSIGNMENT (( #10586 ) ) ; +#18321 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70524 ) ) ; +#18322 = EDGE_LOOP ( 'NONE', ( #74932, #79618, #6529, #58024 ) ) ; +#18323 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82543, 'distance_accuracy_value', 'NONE'); +#18324 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18325 = LINE ( 'NONE', #35215, #59522 ) ; +#18326 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18327 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18328 = AXIS2_PLACEMENT_3D ( 'NONE', #41997, #73134, #32816 ) ; +#18329 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18330 = EDGE_CURVE ( 'NONE', #47689, #6705, #7670, .T. ) ; +#18331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#18332 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97762 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3171, #64462, #95561 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18333 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18334 = VERTEX_POINT ( 'NONE', #38912 ) ; +#18335 = ORIENTED_EDGE ( 'NONE', *, *, #97115, .F. ) ; +#18336 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#18337 = EDGE_CURVE ( 'NONE', #71482, #6999, #63435, .T. ) ; +#18338 = AXIS2_PLACEMENT_3D ( 'NONE', #57257, #43409, #83234 ) ; +#18339 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62606, 'distance_accuracy_value', 'NONE'); +#18340 = SURFACE_STYLE_FILL_AREA ( #58217 ) ; +#18341 = CYLINDRICAL_SURFACE ( 'NONE', #88863, 0.05000000000000012768 ) ; +#18342 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#18343 = CARTESIAN_POINT ( 'NONE', ( -0.5440966885710070144, -1.187196157070490088, 0.8100000000000000533 ) ) ; +#18344 = FILL_AREA_STYLE ('',( #81689 ) ) ; +#18345 = LINE ( 'NONE', #42868, #22462 ) ; +#18346 = FILL_AREA_STYLE_COLOUR ( '', #1330 ) ; +#18347 = SURFACE_SIDE_STYLE ('',( #64837 ) ) ; +#18348 = AXIS2_PLACEMENT_3D ( 'NONE', #74139, #27693, #19996 ) ; +#18349 = EDGE_CURVE ( 'NONE', #2820, #82318, #31747, .T. ) ; +#18350 = ORIENTED_EDGE ( 'NONE', *, *, #63037, .T. ) ; +#18351 = SURFACE_STYLE_FILL_AREA ( #96453 ) ; +#18352 = ORIENTED_EDGE ( 'NONE', *, *, #11270, .T. ) ; +#18353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21488 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74378, #89195, #34591 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18354 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#18355 = VERTEX_POINT ( 'NONE', #77709 ) ; +#18356 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18357 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18358 = SURFACE_SIDE_STYLE ('',( #41881 ) ) ; +#18359 = ADVANCED_FACE ( 'NONE', ( #70036 ), #79755, .T. ) ; +#18360 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18361 = CARTESIAN_POINT ( 'NONE', ( -1.015038904699709921, -1.047446665233070062, 0.8100000000000000533 ) ) ; +#18362 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18363 = DIRECTION ( 'NONE', ( 1.445602896647339903E-15, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18364 = SURFACE_SIDE_STYLE ('',( #88337 ) ) ; +#18366 = ORIENTED_EDGE ( 'NONE', *, *, #68138, .F. ) ; +#18365 = ORIENTED_EDGE ( 'NONE', *, *, #52728, .T. ) ; +#18367 = AXIS2_PLACEMENT_3D ( 'NONE', #13983, #92128, #53345 ) ; +#18368 = ADVANCED_FACE ( 'NONE', ( #47059 ), #78227, .T. ) ; +#18369 = EDGE_CURVE ( 'NONE', #54332, #9858, #58799, .T. ) ; +#18370 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18371 = EDGE_LOOP ( 'NONE', ( #87437, #48959, #40848, #7153 ) ) ; +#18372 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18373 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36333 ), #10125 ) ; +#18374 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18376 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#18375 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#18377 = ORIENTED_EDGE ( 'NONE', *, *, #16729, .F. ) ; +#18378 = VERTEX_POINT ( 'NONE', #42931 ) ; +#18379 = LINE ( 'NONE', #3085, #97059 ) ; +#18380 = SURFACE_STYLE_FILL_AREA ( #96481 ) ; +#18381 = EDGE_CURVE ( 'NONE', #60625, #89867, #65929, .T. ) ; +#18382 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24928 ), #457 ) ; +#18383 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75466 ), #16829 ) ; +#18384 = CARTESIAN_POINT ( 'NONE', ( -0.03713474025974064507, 0.7099999999999999645, 0.5000000000000001110 ) ) ; +#18385 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#18386 = LINE ( 'NONE', #27598, #984 ) ; +#18387 = ORIENTED_EDGE ( 'NONE', *, *, #99319, .T. ) ; +#18388 = ORIENTED_EDGE ( 'NONE', *, *, #60258, .T. ) ; +#18389 = ADVANCED_FACE ( 'NONE', ( #18937 ), #43433, .F. ) ; +#18390 = LINE ( 'NONE', #71027, #84505 ) ; +#18391 = ORIENTED_EDGE ( 'NONE', *, *, #5549, .T. ) ; +#18392 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.7000000000000000666, -0.02000000000000000042 ) ) ; +#18393 = VECTOR ( 'NONE', #3169, 1000.000000000000114 ) ; +#18394 = SURFACE_STYLE_USAGE ( .BOTH. , #15349 ) ; +#18396 = VERTEX_POINT ( 'NONE', #80759 ) ; +#18395 = FACE_OUTER_BOUND ( 'NONE', #6253, .T. ) ; +#18397 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18398 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #63265, #94351, #24465, #87218 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#18399 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18400 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70224 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7016, #47420, #16742 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18401 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18402 = SURFACE_STYLE_FILL_AREA ( #87862 ) ; +#18403 = ORIENTED_EDGE ( 'NONE', *, *, #4702, .F. ) ; +#18404 = CARTESIAN_POINT ( 'NONE', ( -1.031261620021183045, -1.418839292875710756, 0.8099999999996797539 ) ) ; +#18405 = EDGE_LOOP ( 'NONE', ( #52976, #82383, #58169, #2507 ) ) ; +#18406 = FILL_AREA_STYLE_COLOUR ( '', #15468 ) ; +#18407 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18408 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18409 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65743 ) ) ; +#18410 = FILL_AREA_STYLE_COLOUR ( '', #77518 ) ; +#18411 = LINE ( 'NONE', #57262, #98210 ) ; +#18412 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18413 = CARTESIAN_POINT ( 'NONE', ( 10.66704099999999933, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#18414 = LINE ( 'NONE', #57783, #100266 ) ; +#18415 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18416 = VERTEX_POINT ( 'NONE', #58302 ) ; +#18417 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.966666666666666785, 0.000000000000000000 ) ) ; +#18418 = ORIENTED_EDGE ( 'NONE', *, *, #81284, .F. ) ; +#18419 = EDGE_CURVE ( 'NONE', #87325, #67390, #73079, .T. ) ; +#18420 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62481 ) ) ; +#18421 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18422 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18423 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#18424 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18425 = EDGE_CURVE ( 'NONE', #13767, #84630, #35811, .T. ) ; +#18427 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18426 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, 0.1400000000000000133 ) ) ; +#18428 = SURFACE_SIDE_STYLE ('',( #66912 ) ) ; +#18429 = FILL_AREA_STYLE ('',( #88398 ) ) ; +#18430 = MANIFOLD_SOLID_BREP ( 'ÊäÈë178', #25840 ) ; +#18431 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7246 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22204, #52858, #37546 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18432 = PRESENTATION_STYLE_ASSIGNMENT (( #59314 ) ) ; +#18433 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#18434 = AXIS2_PLACEMENT_3D ( 'NONE', #20007, #18987, #65985 ) ; +#18435 = PRESENTATION_STYLE_ASSIGNMENT (( #41454 ) ) ; +#18436 = EDGE_LOOP ( 'NONE', ( #94982, #74531, #22269, #3832 ) ) ; +#18437 = SURFACE_SIDE_STYLE ('',( #24648 ) ) ; +#18438 = EDGE_CURVE ( 'NONE', #95021, #63500, #57482, .T. ) ; +#18441 = SURFACE_STYLE_FILL_AREA ( #34319 ) ; +#18440 = PLANE ( 'NONE', #34503 ) ; +#18439 = STYLED_ITEM ( 'NONE', ( #75816 ), #75916 ) ; +#18442 = SURFACE_STYLE_FILL_AREA ( #49120 ) ; +#18443 = VECTOR ( 'NONE', #39552, 1000.000000000000000 ) ; +#18445 = ORIENTED_EDGE ( 'NONE', *, *, #55961, .T. ) ; +#18444 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44531 ), #33127 ) ; +#18446 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18447 = EDGE_CURVE ( 'NONE', #69086, #46200, #50629, .T. ) ; +#18448 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18449 = CARTESIAN_POINT ( 'NONE', ( -1.024611994374110102, -1.021599245672099920, 0.8299999999999999600 ) ) ; +#18450 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18452 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49996 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52625, #5101, #37790 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18453 = VECTOR ( 'NONE', #8438, 1000.000000000000000 ) ; +#18454 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.05000000000000000278, 0.08229670385730990245 ) ) ; +#18455 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8991599999999999593 ) ) ; +#18456 = FILL_AREA_STYLE_COLOUR ( '', #81791 ) ; +#18457 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18458 = AXIS2_PLACEMENT_3D ( 'NONE', #81190, #51047, #74521 ) ; +#18459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17114, 'distance_accuracy_value', 'NONE'); +#18460 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18461 = FILL_AREA_STYLE ('',( #61208 ) ) ; +#18462 = ORIENTED_EDGE ( 'NONE', *, *, #42498, .T. ) ; +#18463 = FILL_AREA_STYLE_COLOUR ( '', #87257 ) ; +#18465 = VERTEX_POINT ( 'NONE', #55014 ) ; +#18464 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5397 ), #47785 ) ; +#18466 = ADVANCED_FACE ( 'NONE', ( #31500 ), #29129, .F. ) ; +#18467 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89181, 'distance_accuracy_value', 'NONE'); +#18468 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11596, 'distance_accuracy_value', 'NONE'); +#18469 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18470 = SURFACE_STYLE_FILL_AREA ( #55799 ) ; +#18471 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18472 = CARTESIAN_POINT ( 'NONE', ( 0.5425545555084398952, -1.117098638196126092, 0.8100000000000000533 ) ) ; +#18473 = PRESENTATION_STYLE_ASSIGNMENT (( #4175 ) ) ; +#18474 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18475 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18476 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18477 = EDGE_CURVE ( 'NONE', #26121, #33704, #80625, .T. ) ; +#18478 = EDGE_LOOP ( 'NONE', ( #60466, #26108, #95833, #42271 ) ) ; +#18479 = LINE ( 'NONE', #71626, #85250 ) ; +#18480 = CARTESIAN_POINT ( 'NONE', ( -1.476179938779914602, 3.099999999999990319, 0.000000000000000000 ) ) ; +#18481 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.899999999999999911, 0.1829999999999540328 ) ) ; +#18482 = VERTEX_POINT ( 'NONE', #97989 ) ; +#18483 = FILL_AREA_STYLE_COLOUR ( '', #62080 ) ; +#18484 = VECTOR ( 'NONE', #654, 1000.000000000000114 ) ; +#18485 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254300000000129, 0.8991599999999999593 ) ) ; +#18486 = ORIENTED_EDGE ( 'NONE', *, *, #4219, .T. ) ; +#18487 = PRESENTATION_STYLE_ASSIGNMENT (( #4189 ) ) ; +#18488 = ADVANCED_FACE ( 'NONE', ( #59811 ), #44902, .T. ) ; +#18489 = ADVANCED_FACE ( 'NONE', ( #7927 ), #39156, .T. ) ; +#18490 = SURFACE_STYLE_USAGE ( .BOTH. , #2193 ) ; +#18491 = FILL_AREA_STYLE_COLOUR ( '', #75517 ) ; +#18492 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18493 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18494 = LINE ( 'NONE', #25682, #18612 ) ; +#18495 = VERTEX_POINT ( 'NONE', #80499 ) ; +#18497 = ADVANCED_FACE ( 'NONE', ( #41197 ), #47834, .F. ) ; +#18496 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -1.900000000000000133, -0.02000000000000000042 ) ) ; +#18498 = ADVANCED_FACE ( 'NONE', ( #78975 ), #9453, .T. ) ; +#18499 = SURFACE_STYLE_FILL_AREA ( #49682 ) ; +#18500 = ORIENTED_EDGE ( 'NONE', *, *, #15328, .F. ) ; +#18501 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#18502 = FILL_AREA_STYLE_COLOUR ( '', #36046 ) ; +#18503 = EDGE_LOOP ( 'NONE', ( #39493, #86599, #6032, #77075 ) ) ; +#18504 = FILL_AREA_STYLE_COLOUR ( '', #85567 ) ; +#18505 = SURFACE_STYLE_USAGE ( .BOTH. , #57351 ) ; +#18506 = ADVANCED_FACE ( 'NONE', ( #67162 ), #75330, .F. ) ; +#18507 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5425 ), #64225 ) ; +#18508 = CARTESIAN_POINT ( 'NONE', ( -0.4444287376170629744, -1.091919226080539929, 0.8299999999999999600 ) ) ; +#18509 = SURFACE_STYLE_FILL_AREA ( #1176 ) ; +#18510 = FACE_OUTER_BOUND ( 'NONE', #67251, .T. ) ; +#18512 = FILL_AREA_STYLE_COLOUR ( '', #17433 ) ; +#18511 = PLANE ( 'NONE', #92032 ) ; +#18513 = EDGE_LOOP ( 'NONE', ( #94600, #62230, #38615, #42574 ) ) ; +#18514 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #49883, #82894 ), #28905 ) ; +#18516 = ORIENTED_EDGE ( 'NONE', *, *, #65041, .F. ) ; +#18515 = ORIENTED_EDGE ( 'NONE', *, *, #67812, .T. ) ; +#18517 = FILL_AREA_STYLE_COLOUR ( '', #9021 ) ; +#18518 = VECTOR ( 'NONE', #23040, 1000.000000000000000 ) ; +#18519 = ORIENTED_EDGE ( 'NONE', *, *, #57054, .T. ) ; +#18520 = ADVANCED_FACE ( 'NONE', ( #3876 ), #51873, .T. ) ; +#18521 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.850000000000000089, 0.000000000000000000 ) ) ; +#18522 = VECTOR ( 'NONE', #86380, 1000.000000000000000 ) ; +#18523 = ORIENTED_EDGE ( 'NONE', *, *, #98716, .F. ) ; +#18525 = ORIENTED_EDGE ( 'NONE', *, *, #4675, .F. ) ; +#18524 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#18526 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18528 = LINE ( 'NONE', #17007, #98630 ) ; +#18527 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#18529 = PLANE ( 'NONE', #4776 ) ; +#18530 = VERTEX_POINT ( 'NONE', #82015 ) ; +#18531 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#18532 = FILL_AREA_STYLE ('',( #57376 ) ) ; +#18533 = FILL_AREA_STYLE ('',( #9789 ) ) ; +#18534 = ORIENTED_EDGE ( 'NONE', *, *, #29136, .F. ) ; +#18535 = FACE_OUTER_BOUND ( 'NONE', #16356, .T. ) ; +#18536 = FILL_AREA_STYLE ('',( #96124 ) ) ; +#18537 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44602 ), #83780 ) ; +#18538 = SURFACE_STYLE_FILL_AREA ( #26734 ) ; +#18539 = PLANE ( 'NONE', #58207 ) ; +#18540 = AXIS2_PLACEMENT_3D ( 'NONE', #14117, #38162, #37168 ) ; +#18541 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18542 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62604 ) ) ; +#18543 = DIRECTION ( 'NONE', ( -0.3387340427540269649, 0.000000000000000000, -0.9408821649279537347 ) ) ; +#18544 = SURFACE_STYLE_FILL_AREA ( #49732 ) ; +#18545 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#18546 = PRESENTATION_STYLE_ASSIGNMENT (( #88509 ) ) ; +#18547 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#18548 = VECTOR ( 'NONE', #33514, 1000.000000000000000 ) ; +#18549 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.1000000000000016015, 6.729667010201685742E-79 ) ) ; +#18550 = EDGE_CURVE ( 'NONE', #44974, #94101, #75705, .T. ) ; +#18551 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#18552 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.000000000000000000 ) ) ; +#18553 = PRESENTATION_STYLE_ASSIGNMENT (( #80368 ) ) ; +#18554 = VECTOR ( 'NONE', #84790, 1000.000000000000000 ) ; +#18555 = CARTESIAN_POINT ( 'NONE', ( 1.020577689509359898, -0.9509517096142480197, 0.8100000000000000533 ) ) ; +#18556 = ORIENTED_EDGE ( 'NONE', *, *, #24195, .T. ) ; +#18557 = LINE ( 'NONE', #46937, #95253 ) ; +#18558 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49803 ), #93743 ) ; +#18559 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18560 = SURFACE_STYLE_USAGE ( .BOTH. , #50262 ) ; +#18561 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18562 = EDGE_LOOP ( 'NONE', ( #47470, #36421, #49929, #2877, #64079, #7387 ) ) ; +#18563 = FILL_AREA_STYLE_COLOUR ( '', #2524 ) ; +#18564 = FILL_AREA_STYLE ('',( #3762 ) ) ; +#18565 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64216 ), #29993 ) ; +#18567 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18566 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#18568 = CARTESIAN_POINT ( 'NONE', ( 1.596805013731110279, -1.020192282374009940, 0.8299999999999999600 ) ) ; +#18569 = CARTESIAN_POINT ( 'NONE', ( -0.2155512272691150200, -1.399421068953929925, 0.8100000000000000533 ) ) ; +#18570 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18571 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13046 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80319, #10756, #10246 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18572 = ORIENTED_EDGE ( 'NONE', *, *, #76838, .T. ) ; +#18573 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18574 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.09999999999999954758, -0.02000000000000000042 ) ) ; +#18575 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#18576 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#18577 = PLANE ( 'NONE', #72544 ) ; +#18578 = SURFACE_SIDE_STYLE ('',( #2782 ) ) ; +#18579 = AXIS2_PLACEMENT_3D ( 'NONE', #41989, #57319, #26677 ) ; +#18580 = LINE ( 'NONE', #49772, #70870 ) ; +#18581 = SURFACE_SIDE_STYLE ('',( #52150 ) ) ; +#18582 = PLANE ( 'NONE', #29594 ) ; +#18583 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34816, 'distance_accuracy_value', 'NONE'); +#18584 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18585 = ORIENTED_EDGE ( 'NONE', *, *, #76768, .T. ) ; +#18586 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#18587 = VERTEX_POINT ( 'NONE', #34560 ) ; +#18588 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#18589 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57127, 'distance_accuracy_value', 'NONE'); +#18590 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13757, 'distance_accuracy_value', 'NONE'); +#18591 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18592 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18593 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#18594 = VECTOR ( 'NONE', #86887, 1000.000000000000000 ) ; +#18595 = CARTESIAN_POINT ( 'NONE', ( 1.076179938779914913, -3.099999999999980549, 0.000000000000000000 ) ) ; +#18596 = VECTOR ( 'NONE', #92293, 1000.000000000000000 ) ; +#18597 = CARTESIAN_POINT ( 'NONE', ( 1.856855962848350083, -0.9758031678253591412, 0.8100000000000000533 ) ) ; +#18598 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.9238200612200849760, -0.02000000000000000042 ) ) ; +#18599 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65854 ), #3882 ) ; +#18600 = EDGE_CURVE ( 'NONE', #75429, #72474, #83000, .T. ) ; +#18601 = ORIENTED_EDGE ( 'NONE', *, *, #56721, .T. ) ; +#18602 = MANIFOLD_SOLID_BREP ( 'ÊäÈë147', #76304 ) ; +#18603 = LINE ( 'NONE', #78393, #87742 ) ; +#18604 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80381, 'distance_accuracy_value', 'NONE'); +#18607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26810 ) ) ; +#18606 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11966 ) ) ; +#18605 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#18608 = VECTOR ( 'NONE', #96919, 1000.000000000000000 ) ; +#18609 = EDGE_LOOP ( 'NONE', ( #73026, #43505, #54045, #69481 ) ) ; +#18610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59409 ), #13586 ) ; +#18611 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#18612 = VECTOR ( 'NONE', #25204, 1000.000000000000000 ) ; +#18613 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -2.300000000000000266, 0.000000000000000000 ) ) ; +#18614 = SURFACE_STYLE_USAGE ( .BOTH. , #56472 ) ; +#18615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18616 = VERTEX_POINT ( 'NONE', #6321 ) ; +#18617 = AXIS2_PLACEMENT_3D ( 'NONE', #48561, #55221, #97482 ) ; +#18618 = ADVANCED_FACE ( 'NONE', ( #45651 ), #3394, .T. ) ; +#18619 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30470, 'distance_accuracy_value', 'NONE'); +#18620 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.6999999999999996225, 0.1829999999999790405 ) ) ; +#18621 = VECTOR ( 'NONE', #94103, 1000.000000000000000 ) ; +#18622 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18623 = ORIENTED_EDGE ( 'NONE', *, *, #73525, .F. ) ; +#18624 = SURFACE_STYLE_FILL_AREA ( #17116 ) ; +#18625 = VECTOR ( 'NONE', #32463, 1000.000000000000000 ) ; +#18626 = LINE ( 'NONE', #9883, #58561 ) ; +#18627 = PRESENTATION_STYLE_ASSIGNMENT (( #89603 ) ) ; +#18628 = EDGE_CURVE ( 'NONE', #75798, #60060, #37552, .T. ) ; +#18629 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70834 ), #13695 ) ; +#18630 = EDGE_LOOP ( 'NONE', ( #15824, #59358, #54828, #16865 ) ) ; +#18632 = ORIENTED_EDGE ( 'NONE', *, *, #8540, .F. ) ; +#18631 = LINE ( 'NONE', #71779, #67163 ) ; +#18633 = SURFACE_SIDE_STYLE ('',( #87598 ) ) ; +#18634 = PRESENTATION_STYLE_ASSIGNMENT (( #64621 ) ) ; +#18635 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#18636 = PLANE ( 'NONE', #74467 ) ; +#18637 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#18638 = EDGE_LOOP ( 'NONE', ( #73151, #81651, #71470, #23633 ) ) ; +#18639 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18640 = SURFACE_STYLE_USAGE ( .BOTH. , #80463 ) ; +#18641 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72085, #26139, #56283 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18642 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#18643 = ORIENTED_EDGE ( 'NONE', *, *, #59726, .T. ) ; +#18644 = ORIENTED_EDGE ( 'NONE', *, *, #52145, .T. ) ; +#18645 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93619 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64518, #78814, #48705 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18646 = ORIENTED_EDGE ( 'NONE', *, *, #54825, .F. ) ; +#18647 = CARTESIAN_POINT ( 'NONE', ( -0.6761799387799138916, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#18648 = ADVANCED_FACE ( 'NONE', ( #14504 ), #100200, .T. ) ; +#18650 = SURFACE_SIDE_STYLE ('',( #88613 ) ) ; +#18649 = SURFACE_SIDE_STYLE ('',( #9911 ) ) ; +#18651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62711 ) ) ; +#18652 = FACE_OUTER_BOUND ( 'NONE', #39777, .T. ) ; +#18653 = ORIENTED_EDGE ( 'NONE', *, *, #27235, .F. ) ; +#18654 = VECTOR ( 'NONE', #42817, 1000.000000000000000 ) ; +#18655 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18656 = VERTEX_POINT ( 'NONE', #15520 ) ; +#18657 = CARTESIAN_POINT ( 'NONE', ( 1.356532926677350037, -1.378727886756609955, 0.8100000000000000533 ) ) ; +#18658 = PRESENTATION_STYLE_ASSIGNMENT (( #88618 ) ) ; +#18659 = ORIENTED_EDGE ( 'NONE', *, *, #43447, .T. ) ; +#18660 = SURFACE_SIDE_STYLE ('',( #65647 ) ) ; +#18661 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18662 = EDGE_CURVE ( 'NONE', #66714, #60513, #31886, .T. ) ; +#18664 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18663 = SURFACE_STYLE_USAGE ( .BOTH. , #88623 ) ; +#18665 = CARTESIAN_POINT ( 'NONE', ( -1.355486452235469930, -1.128484622308769891, 0.8100000000000000533 ) ) ; +#18666 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 4.135756999999999906, 0.8648700000000000276 ) ) ; +#18667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54572 ), #70874 ) ; +#18668 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90402 ) ) ; +#18669 = FACE_OUTER_BOUND ( 'NONE', #15707, .T. ) ; +#18670 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40178, #38160, #30452, #20564 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#18671 = SURFACE_STYLE_FILL_AREA ( #26878 ) ; +#18672 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18673 = AXIS2_PLACEMENT_3D ( 'NONE', #35255, #66368, #12149 ) ; +#18674 = EDGE_LOOP ( 'NONE', ( #52007, #6331, #46687, #31580 ) ) ; +#18675 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#18676 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#18677 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18678 = SURFACE_STYLE_FILL_AREA ( #71832 ) ; +#18679 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #765 ), #15389 ) ; +#18680 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#18681 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18682 = CARTESIAN_POINT ( 'NONE', ( 1.980091156971985011, 1.421785968405418155, -11.41534935216541946 ) ) ; +#18683 = SURFACE_STYLE_USAGE ( .BOTH. , #50400 ) ; +#18684 = ORIENTED_EDGE ( 'NONE', *, *, #8661, .T. ) ; +#18685 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#18686 = EDGE_CURVE ( 'NONE', #69898, #63765, #380, .T. ) ; +#18687 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18688 = SURFACE_SIDE_STYLE ('',( #88655 ) ) ; +#18689 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18690 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18761 ), #31753 ) ; +#18691 = SURFACE_SIDE_STYLE ('',( #18177 ) ) ; +#18692 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58781, 'distance_accuracy_value', 'NONE'); +#18693 = FILL_AREA_STYLE ('',( #35072 ) ) ; +#18694 = PRESENTATION_STYLE_ASSIGNMENT (( #64189 ) ) ; +#18695 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#18696 = EDGE_CURVE ( 'NONE', #25891, #65755, #10317, .T. ) ; +#18697 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#18698 = PLANE ( 'NONE', #87523 ) ; +#18699 = SURFACE_SIDE_STYLE ('',( #66195 ) ) ; +#18700 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, -3.500000000000000444, 0.000000000000000000 ) ) ; +#18701 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18702 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18703 = SURFACE_STYLE_USAGE ( .BOTH. , #94794 ) ; +#18704 = SURFACE_STYLE_FILL_AREA ( #88672 ) ; +#18705 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18706 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#18707 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18708 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#18709 = SURFACE_STYLE_USAGE ( .BOTH. , #34083 ) ; +#18710 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34400, #44030, #20542, #11791, #83355, #89512, #65499, #89992, #98085, #73679, #27239, #28228, #66019, #26732 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000006106, 0.3750000000000019984, 0.4375000000000023870, 0.5000000000000027756, 0.7500000000000013323, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#18711 = PRESENTATION_STYLE_ASSIGNMENT (( #17705 ) ) ; +#18712 = ADVANCED_FACE ( 'NONE', ( #87519 ), #40576, .T. ) ; +#18713 = ORIENTED_EDGE ( 'NONE', *, *, #11167, .F. ) ; +#18714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18715 = EDGE_CURVE ( 'NONE', #29842, #26843, #16036, .T. ) ; +#18716 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6969, 'distance_accuracy_value', 'NONE'); +#18717 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#18718 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52620, 'distance_accuracy_value', 'NONE'); +#18719 = FILL_AREA_STYLE_COLOUR ( '', #53590 ) ; +#18721 = VECTOR ( 'NONE', #33072, 1000.000000000000114 ) ; +#18720 = PRESENTATION_STYLE_ASSIGNMENT (( #88683 ) ) ; +#18722 = SURFACE_STYLE_FILL_AREA ( #27420 ) ; +#18723 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26928 ) ) ; +#18724 = EDGE_LOOP ( 'NONE', ( #22085, #80110, #7412, #8368, #90843, #92593 ) ) ; +#18725 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18726 = FACE_OUTER_BOUND ( 'NONE', #66863, .T. ) ; +#18727 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000000971, 0.2400000000000000189 ) ) ; +#18728 = EDGE_CURVE ( 'NONE', #95470, #12578, #48973, .T. ) ; +#18729 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48466, 'distance_accuracy_value', 'NONE'); +#18730 = LINE ( 'NONE', #10477, #12028 ) ; +#18731 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31792 ), #25345 ) ; +#18732 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99929, 'distance_accuracy_value', 'NONE'); +#18733 = ORIENTED_EDGE ( 'NONE', *, *, #9556, .T. ) ; +#18734 = ORIENTED_EDGE ( 'NONE', *, *, #30114, .F. ) ; +#18735 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66068 ) ) ; +#18736 = VECTOR ( 'NONE', #75844, 1000.000000000000000 ) ; +#18737 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18738 = LINE ( 'NONE', #79552, #83387 ) ; +#18739 = VERTEX_POINT ( 'NONE', #17543 ) ; +#18740 = CARTESIAN_POINT ( 'NONE', ( 0.2603867800980460001, -1.020295711170670083, 0.8299999999999996270 ) ) ; +#18741 = PLANE ( 'NONE', #61372 ) ; +#18742 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18743 = FILL_AREA_STYLE_COLOUR ( '', #28783 ) ; +#18744 = SURFACE_STYLE_USAGE ( .BOTH. , #74908 ) ; +#18745 = VECTOR ( 'NONE', #6794, 1000.000000000000000 ) ; +#18746 = ADVANCED_FACE ( 'NONE', ( #2273 ), #48740, .F. ) ; +#18747 = SHAPE_DEFINITION_REPRESENTATION ( #71987, #88620 ) ; +#18748 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18750 = ORIENTED_EDGE ( 'NONE', *, *, #30721, .F. ) ; +#18749 = ORIENTED_EDGE ( 'NONE', *, *, #55112, .F. ) ; +#18751 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#18752 = ORIENTED_EDGE ( 'NONE', *, *, #72790, .F. ) ; +#18753 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18754 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36717 ) ) ; +#18755 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#18756 = LINE ( 'NONE', #34131, #15384 ) ; +#18757 = VERTEX_POINT ( 'NONE', #25756 ) ; +#18758 = MANIFOLD_SOLID_BREP ( 'ÊäÈë99', #63320 ) ; +#18759 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#18760 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#18761 = STYLED_ITEM ( 'NONE', ( #23168 ), #68269 ) ; +#18762 = ORIENTED_EDGE ( 'NONE', *, *, #89145, .F. ) ; +#18763 = ORIENTED_EDGE ( 'NONE', *, *, #97919, .F. ) ; +#18764 = AXIS2_PLACEMENT_3D ( 'NONE', #45006, #85334, #6169 ) ; +#18765 = FILL_AREA_STYLE_COLOUR ( '', #40406 ) ; +#18766 = VERTEX_POINT ( 'NONE', #90534 ) ; +#18767 = ORIENTED_EDGE ( 'NONE', *, *, #75660, .T. ) ; +#18768 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#18769 = EDGE_CURVE ( 'NONE', #50950, #48662, #12850, .T. ) ; +#18770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18771 = AXIS2_PLACEMENT_3D ( 'NONE', #86360, #16370, #70527 ) ; +#18772 = AXIS2_PLACEMENT_3D ( 'NONE', #74049, #43898, #65892 ) ; +#18774 = VERTEX_POINT ( 'NONE', #89543 ) ; +#18773 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#18775 = FILL_AREA_STYLE_COLOUR ( '', #82454 ) ; +#18776 = ORIENTED_EDGE ( 'NONE', *, *, #29125, .T. ) ; +#18777 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000000000888, 0.000000000000000000 ) ) ; +#18778 = STYLED_ITEM ( 'NONE', ( #40483 ), #89864 ) ; +#18779 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20393 ) ) ; +#18780 = ORIENTED_EDGE ( 'NONE', *, *, #62669, .T. ) ; +#18782 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18781 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#18783 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18784 = EDGE_LOOP ( 'NONE', ( #30440, #36311, #17610, #45862 ) ) ; +#18785 = EDGE_LOOP ( 'NONE', ( #21807, #34611, #43491, #14442 ) ) ; +#18786 = ADVANCED_FACE ( 'NONE', ( #50765, #34434 ), #11828, .F. ) ; +#18788 = LINE ( 'NONE', #79098, #65023 ) ; +#18787 = FILL_AREA_STYLE_COLOUR ( '', #94728 ) ; +#18789 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85633 ) ) ; +#18790 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.4999999999999998890, -0.02000000000000000042 ) ) ; +#18791 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#18792 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18793 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75768 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20084, #65541, #12859 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18794 = CARTESIAN_POINT ( 'NONE', ( -0.3688379042909170069, -1.119121047813059988, 0.8299999999999999600 ) ) ; +#18795 = ADVANCED_FACE ( 'NONE', ( #59441 ), #19064, .F. ) ; +#18796 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21252, #98784, #84053 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18797 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#18798 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #99270 ) ; +#18799 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#18800 = ORIENTED_EDGE ( 'NONE', *, *, #62462, .T. ) ; +#18801 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93762 ) ) ; +#18802 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#18803 = EDGE_LOOP ( 'NONE', ( #94064, #96838, #7041, #90294 ) ) ; +#18804 = EDGE_CURVE ( 'NONE', #50362, #71141, #44547, .T. ) ; +#18805 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.000000000000000000, -12.01999999999999957 ) ) ; +#18806 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18807 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#18808 = STYLED_ITEM ( 'NONE', ( #6602 ), #20708 ) ; +#18809 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#18810 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#18812 = VECTOR ( 'NONE', #69291, 1000.000000000000114 ) ; +#18811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18813 = PLANE ( 'NONE', #56654 ) ; +#18814 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18815 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#18816 = ORIENTED_EDGE ( 'NONE', *, *, #51261, .T. ) ; +#18817 = STYLED_ITEM ( 'NONE', ( #17393 ), #38866 ) ; +#18818 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18819 = VECTOR ( 'NONE', #15420, 1000.000000000000000 ) ; +#18820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18821 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#18822 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#18823 = PLANE ( 'NONE', #69139 ) ; +#18824 = STYLED_ITEM ( 'NONE', ( #32377 ), #4434 ) ; +#18825 = EDGE_CURVE ( 'NONE', #25581, #91841, #37436, .T. ) ; +#18826 = STYLED_ITEM ( 'NONE', ( #11087 ), #98313 ) ; +#18827 = SURFACE_STYLE_FILL_AREA ( #67301 ) ; +#18828 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18829 = FILL_AREA_STYLE_COLOUR ( '', #66653 ) ; +#18830 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7694, 'distance_accuracy_value', 'NONE'); +#18831 = SHAPE_REPRESENTATION ( 'ESP32-S3-MINI-1U_V1_3D', ( #29059, #32341, #48681, #46966 ), #27466 ) ; +#18832 = ORIENTED_EDGE ( 'NONE', *, *, #62216, .T. ) ; +#18833 = SURFACE_STYLE_USAGE ( .BOTH. , #72458 ) ; +#18834 = CARTESIAN_POINT ( 'NONE', ( 1.560249861737120103, -0.9531265814360270205, 0.8299999999999999600 ) ) ; +#18835 = SURFACE_STYLE_USAGE ( .BOTH. , #4034 ) ; +#18836 = EDGE_CURVE ( 'NONE', #87468, #16653, #60433, .T. ) ; +#18837 = EDGE_LOOP ( 'NONE', ( #7510, #62891, #48060, #100571 ) ) ; +#18838 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18839 = FACE_OUTER_BOUND ( 'NONE', #16707, .T. ) ; +#18840 = LINE ( 'NONE', #2538, #48039 ) ; +#18841 = EDGE_CURVE ( 'NONE', #51456, #79320, #68534, .T. ) ; +#18842 = FILL_AREA_STYLE ('',( #96435 ) ) ; +#18843 = VECTOR ( 'NONE', #63296, 1000.000000000000114 ) ; +#18844 = PLANE ( 'NONE', #38298 ) ; +#18845 = VERTEX_POINT ( 'NONE', #84376 ) ; +#18846 = VERTEX_POINT ( 'NONE', #5724 ) ; +#18847 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#18848 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.699999999999999956, 0.1829999999999919746 ) ) ; +#18849 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.5238200612200850648, 0.000000000000000000 ) ) ; +#18850 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18851 = ADVANCED_FACE ( 'NONE', ( #61922 ), #28739, .T. ) ; +#18852 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18853 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18854 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#18855 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#18856 = STYLED_ITEM ( 'NONE', ( #18627 ), #49536 ) ; +#18857 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#18858 = ORIENTED_EDGE ( 'NONE', *, *, #64754, .F. ) ; +#18859 = EDGE_CURVE ( 'NONE', #3341, #38122, #100567, .T. ) ; +#18860 = VECTOR ( 'NONE', #73920, 1000.000000000000000 ) ; +#18861 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#18862 = ORIENTED_EDGE ( 'NONE', *, *, #83673, .T. ) ; +#18863 = FILL_AREA_STYLE ('',( #58730 ) ) ; +#18864 = STYLED_ITEM ( 'NONE', ( #20291 ), #78551 ) ; +#18865 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97133 ), #31935 ) ; +#18866 = PLANE ( 'NONE', #15395 ) ; +#18867 = CARTESIAN_POINT ( 'NONE', ( -1.038413249809780003, -1.000241703689469963, 0.8100000000000000533 ) ) ; +#18868 = EDGE_CURVE ( 'NONE', #34733, #21114, #30734, .T. ) ; +#18869 = CARTESIAN_POINT ( 'NONE', ( 6.527800000000000047, 11.44270000000000032, 0.8991599999999999593 ) ) ; +#18870 = VECTOR ( 'NONE', #5423, 1000.000000000000000 ) ; +#18871 = LINE ( 'NONE', #33730, #62113 ) ; +#18872 = SURFACE_STYLE_USAGE ( .BOTH. , #73531 ) ; +#18873 = EDGE_CURVE ( 'NONE', #3550, #61874, #21095, .T. ) ; +#18875 = ORIENTED_EDGE ( 'NONE', *, *, #37454, .T. ) ; +#18874 = ORIENTED_EDGE ( 'NONE', *, *, #53679, .F. ) ; +#18876 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18877 = FILL_AREA_STYLE_COLOUR ( '', #2789 ) ; +#18878 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18879 = ORIENTED_EDGE ( 'NONE', *, *, #54863, .F. ) ; +#18880 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#18881 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52537 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42371, #79669, #65844 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18882 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87015 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79280, #9242, #56336 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18883 = CYLINDRICAL_SURFACE ( 'NONE', #58726, 0.1099999999999998479 ) ; +#18884 = EDGE_LOOP ( 'NONE', ( #31993, #18335, #87473, #53459 ) ) ; +#18885 = ORIENTED_EDGE ( 'NONE', *, *, #71193, .F. ) ; +#18887 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66212 ) ) ; +#18886 = LINE ( 'NONE', #80713, #5721 ) ; +#18888 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666646623, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#18889 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18890 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#18892 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#18891 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6166666666666666963, 0.000000000000000000 ) ) ; +#18893 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#18894 = ORIENTED_EDGE ( 'NONE', *, *, #90885, .T. ) ; +#18895 = ORIENTED_EDGE ( 'NONE', *, *, #15147, .T. ) ; +#18896 = FILL_AREA_STYLE ('',( #88865 ) ) ; +#18897 = VERTEX_POINT ( 'NONE', #83389 ) ; +#18898 = LINE ( 'NONE', #57765, #75853 ) ; +#18899 = LINE ( 'NONE', #3098, #23202 ) ; +#18900 = VECTOR ( 'NONE', #57243, 1000.000000000000227 ) ; +#18901 = EDGE_CURVE ( 'NONE', #90220, #18616, #13341, .T. ) ; +#18902 = AXIS2_PLACEMENT_3D ( 'NONE', #68243, #44260, #14096 ) ; +#18904 = EDGE_LOOP ( 'NONE', ( #8370, #61382, #22834, #67354 ) ) ; +#18903 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#18905 = STYLED_ITEM ( 'NONE', ( #55470 ), #12993 ) ; +#18906 = SURFACE_SIDE_STYLE ('',( #73052 ) ) ; +#18907 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18908 = FILL_AREA_STYLE_COLOUR ( '', #9661 ) ; +#18909 = VERTEX_POINT ( 'NONE', #99103 ) ; +#18910 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18911 = ORIENTED_EDGE ( 'NONE', *, *, #32442, .F. ) ; +#18912 = ADVANCED_FACE ( 'NONE', ( #29256 ), #91531, .F. ) ; +#18913 = ADVANCED_FACE ( 'NONE', ( #72089 ), #32279, .F. ) ; +#18914 = LINE ( 'NONE', #74576, #62835 ) ; +#18915 = FACE_OUTER_BOUND ( 'NONE', #99194, .T. ) ; +#18916 = CARTESIAN_POINT ( 'NONE', ( -1.049523990565160103, -1.254158608853950030, 0.8300000000000000711 ) ) ; +#18917 = ADVANCED_FACE ( 'NONE', ( #47590 ), #62423, .F. ) ; +#18918 = VECTOR ( 'NONE', #68262, 1000.000000000000000 ) ; +#18919 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#18920 = LINE ( 'NONE', #43420, #63919 ) ; +#18922 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#18921 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#18923 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18924 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61389 ) ) ; +#18925 = ORIENTED_EDGE ( 'NONE', *, *, #46221, .F. ) ; +#18926 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#18927 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #50203 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #52434 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#18928 = ORIENTED_EDGE ( 'NONE', *, *, #25421, .F. ) ; +#18929 = ADVANCED_FACE ( 'NONE', ( #86906 ), #63927, .T. ) ; +#18930 = SURFACE_SIDE_STYLE ('',( #8667 ) ) ; +#18931 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#18932 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#18933 = STYLED_ITEM ( 'NONE', ( #28394 ), #83825 ) ; +#18934 = VECTOR ( 'NONE', #65046, 1000.000000000000000 ) ; +#18935 = PLANE ( 'NONE', #77929 ) ; +#18937 = FACE_OUTER_BOUND ( 'NONE', #5556, .T. ) ; +#18936 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2808578643762702498, 0.1434314575050751328 ) ) ; +#18938 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#18939 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#18940 = LINE ( 'NONE', #42456, #49954 ) ; +#18941 = MANIFOLD_SOLID_BREP ( 'ÊäÈë146', #25761 ) ; +#18942 = STYLED_ITEM ( 'NONE', ( #23196 ), #83045 ) ; +#18943 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, 0.000000000000000000 ) ) ; +#18944 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#18945 = SURFACE_STYLE_FILL_AREA ( #34315 ) ; +#18946 = VECTOR ( 'NONE', #37243, 1000.000000000000000 ) ; +#18947 = PLANE ( 'NONE', #44996 ) ; +#18948 = ADVANCED_FACE ( 'NONE', ( #50639 ), #11708, .T. ) ; +#18949 = ADVANCED_FACE ( 'NONE', ( #79076 ), #10026, .F. ) ; +#18950 = ORIENTED_EDGE ( 'NONE', *, *, #29674, .F. ) ; +#18951 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#18952 = FILL_AREA_STYLE_COLOUR ( '', #10133 ) ; +#18953 = FILL_AREA_STYLE_COLOUR ( '', #14590 ) ; +#18954 = SURFACE_SIDE_STYLE ('',( #89413 ) ) ; +#18955 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48833, 'distance_accuracy_value', 'NONE'); +#18956 = ORIENTED_EDGE ( 'NONE', *, *, #72654, .T. ) ; +#18957 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18958 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#18959 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#18960 = ADVANCED_FACE ( 'NONE', ( #32107 ), #18255, .T. ) ; +#18961 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#18962 = CARTESIAN_POINT ( 'NONE', ( 1.723820061220085353, -3.099999999999970335, 0.000000000000000000 ) ) ; +#18963 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.44219999999999970, 0.8648700000000000276 ) ) ; +#18964 = FACE_OUTER_BOUND ( 'NONE', #41149, .T. ) ; +#18965 = LINE ( 'NONE', #86541, #70009 ) ; +#18966 = PLANE ( 'NONE', #51284 ) ; +#18967 = AXIS2_PLACEMENT_3D ( 'NONE', #90101, #28822, #60009 ) ; +#18968 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#18969 = ORIENTED_EDGE ( 'NONE', *, *, #13639, .T. ) ; +#18970 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#18971 = ORIENTED_EDGE ( 'NONE', *, *, #45341, .F. ) ; +#18972 = CIRCLE ( 'NONE', #5885, 0.009999999999999998473 ) ; +#18973 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#18974 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35623, 'distance_accuracy_value', 'NONE'); +#18975 = FILL_AREA_STYLE ('',( #74124 ) ) ; +#18976 = FILL_AREA_STYLE ('',( #40482 ) ) ; +#18977 = FACE_OUTER_BOUND ( 'NONE', #3064, .T. ) ; +#18978 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10734 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58506, #10896, #12408 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#18979 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, 0.000000000000000000 ) ) ; +#18980 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18981 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#18982 = ORIENTED_EDGE ( 'NONE', *, *, #56516, .F. ) ; +#18983 = PLANE ( 'NONE', #4179 ) ; +#18984 = SURFACE_SIDE_STYLE ('',( #57847 ) ) ; +#18985 = ORIENTED_EDGE ( 'NONE', *, *, #70227, .F. ) ; +#18986 = EDGE_LOOP ( 'NONE', ( #90886, #11560, #27330, #98919 ) ) ; +#18987 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#18988 = VECTOR ( 'NONE', #66037, 1000.000000000000114 ) ; +#18989 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#18990 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626904202, -0.1434314575050762430 ) ) ; +#18991 = SURFACE_STYLE_USAGE ( .BOTH. , #81828 ) ; +#18992 = EDGE_CURVE ( 'NONE', #22729, #65258, #21743, .T. ) ; +#18993 = ORIENTED_EDGE ( 'NONE', *, *, #60600, .T. ) ; +#18994 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#18995 = ORIENTED_EDGE ( 'NONE', *, *, #29724, .T. ) ; +#18996 = PLANE ( 'NONE', #90022 ) ; +#18997 = VECTOR ( 'NONE', #42831, 1000.000000000000000 ) ; +#18998 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97010, 'distance_accuracy_value', 'NONE'); +#18999 = EDGE_CURVE ( 'NONE', #79963, #87284, #88021, .T. ) ; +#19000 = ORIENTED_EDGE ( 'NONE', *, *, #67418, .T. ) ; +#19001 = VECTOR ( 'NONE', #95407, 1000.000000000000000 ) ; +#19002 = ORIENTED_EDGE ( 'NONE', *, *, #65533, .T. ) ; +#19003 = VECTOR ( 'NONE', #22955, 1000.000000000000000 ) ; +#19004 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19005 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19006 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#19007 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#19008 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90737 ), #36964 ) ; +#19009 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#19010 = ORIENTED_EDGE ( 'NONE', *, *, #50298, .T. ) ; +#19012 = ORIENTED_EDGE ( 'NONE', *, *, #78001, .F. ) ; +#19011 = EDGE_LOOP ( 'NONE', ( #29775, #59095 ) ) ; +#19013 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#19014 = ORIENTED_EDGE ( 'NONE', *, *, #53115, .T. ) ; +#19015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46704 ), #50042 ) ; +#19016 = ADVANCED_FACE ( 'NONE', ( #53620 ), #68897, .T. ) ; +#19017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63078 ), #1033 ) ; +#19018 = ORIENTED_EDGE ( 'NONE', *, *, #3544, .T. ) ; +#19020 = ORIENTED_EDGE ( 'NONE', *, *, #45328, .F. ) ; +#19019 = FILL_AREA_STYLE ('',( #88993 ) ) ; +#19021 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19022 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74524 ), #92403 ) ; +#19023 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.500000000000000222, 0.1829999999999580296 ) ) ; +#19024 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19025 = PLANE ( 'NONE', #27703 ) ; +#19026 = EDGE_LOOP ( 'NONE', ( #71324, #81358, #40026, #73505 ) ) ; +#19027 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#19028 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19029 = ORIENTED_EDGE ( 'NONE', *, *, #71165, .T. ) ; +#19030 = ADVANCED_FACE ( 'NONE', ( #66914 ), #43936, .T. ) ; +#19031 = FILL_AREA_STYLE_COLOUR ( '', #36750 ) ; +#19032 = VECTOR ( 'NONE', #2900, 1000.000000000000000 ) ; +#19033 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#19034 = SURFACE_SIDE_STYLE ('',( #89009 ) ) ; +#19035 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19036 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999734, 0.6892893218813451739, 0.9757359312880716784 ) ) ; +#19037 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19038 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#19039 = FILL_AREA_STYLE_COLOUR ( '', #88749 ) ; +#19040 = SURFACE_STYLE_FILL_AREA ( #20552 ) ; +#19041 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#19042 = EDGE_CURVE ( 'NONE', #67739, #36855, #84253, .T. ) ; +#19043 = FACE_OUTER_BOUND ( 'NONE', #62185, .T. ) ; +#19044 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87578 ), #12485 ) ; +#19045 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19046 = ADVANCED_FACE ( 'NONE', ( #30107 ), #84742, .T. ) ; +#19047 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#19048 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19049 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.266666666666659946, 3.495651678170121160E-76 ) ) ; +#19050 = SURFACE_SIDE_STYLE ('',( #74714 ) ) ; +#19051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19052 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19053 = ORIENTED_EDGE ( 'NONE', *, *, #13995, .T. ) ; +#19054 = CARTESIAN_POINT ( 'NONE', ( -1.303498337670309981, -1.475020827802409951, 0.8300000000000024025 ) ) ; +#19055 = EDGE_CURVE ( 'NONE', #5141, #22958, #8053, .T. ) ; +#19056 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#19057 = SURFACE_SIDE_STYLE ('',( #52628 ) ) ; +#19058 = EDGE_CURVE ( 'NONE', #38354, #99634, #31133, .T. ) ; +#19059 = FILL_AREA_STYLE ('',( #41571 ) ) ; +#19060 = VERTEX_POINT ( 'NONE', #9077 ) ; +#19061 = LINE ( 'NONE', #10832, #46509 ) ; +#19062 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89202 ) ) ; +#19064 = PLANE ( 'NONE', #68873 ) ; +#19063 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#19065 = CARTESIAN_POINT ( 'NONE', ( 1.634048567103850047, -0.9784189978443861291, 0.8100000000000000533 ) ) ; +#19066 = EDGE_CURVE ( 'NONE', #70624, #99988, #94400, .T. ) ; +#19067 = EDGE_CURVE ( 'NONE', #64435, #10531, #100439, .T. ) ; +#19068 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19069 = VECTOR ( 'NONE', #68778, 1000.000000000000000 ) ; +#19070 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19071 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19072 = FILL_AREA_STYLE ('',( #81413 ) ) ; +#19073 = VERTEX_POINT ( 'NONE', #79122 ) ; +#19074 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000000804, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#19075 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74575 ), #68034 ) ; +#19076 = LINE ( 'NONE', #66551, #49480 ) ; +#19077 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#19078 = DIRECTION ( 'NONE', ( -0.9312650831180608879, 0.000000000000000000, 0.3643423458302799678 ) ) ; +#19079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19080 = EDGE_CURVE ( 'NONE', #21904, #31700, #32149, .T. ) ; +#19081 = LINE ( 'NONE', #56931, #46846 ) ; +#19082 = FILL_AREA_STYLE ('',( #89053 ) ) ; +#19083 = VECTOR ( 'NONE', #64409, 1000.000000000000000 ) ; +#19084 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19085 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#19086 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19087 = ADVANCED_FACE ( 'NONE', ( #31630 ), #23481, .T. ) ; +#19088 = FACE_OUTER_BOUND ( 'NONE', #19817, .T. ) ; +#19089 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#19090 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -0.03333333333333517862, 0.000000000000000000 ) ) ; +#19091 = STYLED_ITEM ( 'NONE', ( #6735 ), #23893 ) ; +#19092 = VECTOR ( 'NONE', #97038, 1000.000000000000000 ) ; +#19093 = ORIENTED_EDGE ( 'NONE', *, *, #60717, .T. ) ; +#19094 = ORIENTED_EDGE ( 'NONE', *, *, #981, .T. ) ; +#19095 = LINE ( 'NONE', #90051, #35565 ) ; +#19096 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19097 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1458578643762690197 ) ) ; +#19099 = VECTOR ( 'NONE', #20217, 999.9999999999998863 ) ; +#19098 = SURFACE_SIDE_STYLE ('',( #26296 ) ) ; +#19100 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19101 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19102 = LINE ( 'NONE', #96691, #99292 ) ; +#19103 = FILL_AREA_STYLE ('',( #49271 ) ) ; +#19104 = CLOSED_SHELL ( 'NONE', ( #26611, #81322, #10468, #32397, #47769, #16063 ) ) ; +#19105 = ORIENTED_EDGE ( 'NONE', *, *, #43271, .T. ) ; +#19106 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19107 = MANIFOLD_SOLID_BREP ( 'ÊäÈë28', #35480 ) ; +#19108 = VECTOR ( 'NONE', #95562, 1000.000000000000000 ) ; +#19109 = ORIENTED_EDGE ( 'NONE', *, *, #30343, .T. ) ; +#19110 = LINE ( 'NONE', #1808, #85286 ) ; +#19111 = AXIS2_PLACEMENT_3D ( 'NONE', #99017, #83810, #77134 ) ; +#19112 = PRESENTATION_STYLE_ASSIGNMENT (( #35485 ) ) ; +#19113 = STYLED_ITEM ( 'NONE', ( #56123 ), #14708 ) ; +#19114 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19115 = SURFACE_SIDE_STYLE ('',( #89092 ) ) ; +#19116 = CARTESIAN_POINT ( 'NONE', ( -1.147487226257349890, -1.445368494507049961, 0.8100000000000000533 ) ) ; +#19117 = EDGE_CURVE ( 'NONE', #24875, #44001, #85741, .T. ) ; +#19118 = EDGE_LOOP ( 'NONE', ( #77048, #93942, #22503, #71514 ) ) ; +#19119 = CARTESIAN_POINT ( 'NONE', ( 10.36298512487495493, 4.857005124874956614, 0.8648700000000000276 ) ) ; +#19120 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#19121 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19122 = ADVANCED_FACE ( 'NONE', ( #57166 ), #48495, .T. ) ; +#19123 = CARTESIAN_POINT ( 'NONE', ( 1.799202792133490103, -1.182875588085640306, 0.8099999999999998312 ) ) ; +#19124 = ORIENTED_EDGE ( 'NONE', *, *, #81403, .F. ) ; +#19125 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19126 = FILL_AREA_STYLE ('',( #26836 ) ) ; +#19127 = CARTESIAN_POINT ( 'NONE', ( -1.098619252964047721, -1.237666169257943150, 0.8099999999998132028 ) ) ; +#19128 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4408 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63185, #58557, #43674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19129 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#19130 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19131 = VECTOR ( 'NONE', #38662, 1000.000000000000000 ) ; +#19132 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11553, #58146, #20805, #51971 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 7.494929894286337762E-15, 7.071456404014545558E-05 ), + .UNSPECIFIED. ) ; +#19133 = VERTEX_POINT ( 'NONE', #72960 ) ; +#19135 = ORIENTED_EDGE ( 'NONE', *, *, #31611, .F. ) ; +#19134 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19136 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60581 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85001, #68662, #15013 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19137 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19134, 'distance_accuracy_value', 'NONE'); +#19138 = FILL_AREA_STYLE ('',( #65617 ) ) ; +#19139 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#19140 = SURFACE_STYLE_USAGE ( .BOTH. , #46884 ) ; +#19141 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19142 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146563249, 0.3100465759269649402, 0.8100000000000000533 ) ) ; +#19143 = VERTEX_POINT ( 'NONE', #66308 ) ; +#19144 = VECTOR ( 'NONE', #54798, 1000.000000000000000 ) ; +#19145 = EDGE_CURVE ( 'NONE', #18067, #7390, #70724, .T. ) ; +#19146 = CARTESIAN_POINT ( 'NONE', ( 1.329279248099940025, -1.493640573211080014, 0.8299999999999999600 ) ) ; +#19147 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19148 = FILL_AREA_STYLE_COLOUR ( '', #26900 ) ; +#19149 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#19150 = ORIENTED_EDGE ( 'NONE', *, *, #53525, .T. ) ; +#19151 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16441 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34300, #49606, #3123 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19153 = SURFACE_STYLE_USAGE ( .BOTH. , #59027 ) ; +#19152 = LINE ( 'NONE', #28346, #29204 ) ; +#19154 = VERTEX_POINT ( 'NONE', #33152 ) ; +#19155 = ORIENTED_EDGE ( 'NONE', *, *, #20109, .T. ) ; +#19156 = SURFACE_SIDE_STYLE ('',( #71798 ) ) ; +#19157 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19159 = LINE ( 'NONE', #50367, #95553 ) ; +#19158 = FACE_OUTER_BOUND ( 'NONE', #21045, .T. ) ; +#19160 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19161 = VECTOR ( 'NONE', #12358, 1000.000000000000000 ) ; +#19162 = ORIENTED_EDGE ( 'NONE', *, *, #49081, .F. ) ; +#19163 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19164 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86073 ) ) ; +#19165 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81024, #79502, #47844, #8947, #18682, #71322, #72317, #9461, #88161, #10432, #33024, #94270, #78984, #32541, #95270, #96284 ), + .UNSPECIFIED., .F., .F., + ( 4, 3, 3, 3, 3, 4 ), + ( 0.000000000000000000, 1.675113850726955007E-05, 3.351105738034565131E-05, 5.009631386353259917E-05, 6.599019820942689555E-05, 8.036326568216571012E-05 ), + .UNSPECIFIED. ) ; +#19166 = FILL_AREA_STYLE_COLOUR ( '', #93070 ) ; +#19167 = ORIENTED_EDGE ( 'NONE', *, *, #59147, .T. ) ; +#19168 = CARTESIAN_POINT ( 'NONE', ( 1.343121150739609915, -1.400043273498609908, 0.8299999999999999600 ) ) ; +#19169 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#19170 = EDGE_LOOP ( 'NONE', ( #70304, #92663, #16718, #46407 ) ) ; +#19171 = FILL_AREA_STYLE_COLOUR ( '', #68148 ) ; +#19172 = CLOSED_SHELL ( 'NONE', ( #46356, #40884, #57170, #50167, #72567, #58796 ) ) ; +#19174 = FILL_AREA_STYLE ('',( #59554 ) ) ; +#19173 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19175 = CARTESIAN_POINT ( 'NONE', ( -0.9897739841320261078, -1.331314275383060020, 0.8100000000000000533 ) ) ; +#19176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94146 ), #14248 ) ; +#19177 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#19178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63246 ) ) ; +#19179 = PRESENTATION_STYLE_ASSIGNMENT (( #97752 ) ) ; +#19180 = PLANE ( 'NONE', #60890 ) ; +#19181 = STYLED_ITEM ( 'NONE', ( #61146 ), #14872 ) ; +#19182 = ORIENTED_EDGE ( 'NONE', *, *, #55055, .F. ) ; +#19183 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#19184 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19185 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19186 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#19187 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75742, 'distance_accuracy_value', 'NONE'); +#19188 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8648700000000000276 ) ) ; +#19189 = VECTOR ( 'NONE', #12116, 1000.000000000000000 ) ; +#19190 = EDGE_CURVE ( 'NONE', #11006, #100076, #65291, .T. ) ; +#19191 = FACE_OUTER_BOUND ( 'NONE', #16324, .T. ) ; +#19192 = SURFACE_STYLE_USAGE ( .BOTH. , #32542 ) ; +#19193 = ORIENTED_EDGE ( 'NONE', *, *, #87145, .T. ) ; +#19194 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#19195 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19196 = PRESENTATION_STYLE_ASSIGNMENT (( #35573 ) ) ; +#19197 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#19198 = CARTESIAN_POINT ( 'NONE', ( 0.4653200840722879761, -1.100151516462789969, 0.8300000000000015143 ) ) ; +#19199 = PRESENTATION_STYLE_ASSIGNMENT (( #89675 ) ) ; +#19200 = SURFACE_STYLE_USAGE ( .BOTH. , #89176 ) ; +#19201 = SURFACE_SIDE_STYLE ('',( #11975 ) ) ; +#19202 = ADVANCED_FACE ( 'NONE', ( #64293 ), #19325, .T. ) ; +#19203 = FACE_OUTER_BOUND ( 'NONE', #33201, .T. ) ; +#19204 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#19205 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#19206 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#19207 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19208 = PRESENTATION_STYLE_ASSIGNMENT (( #20732 ) ) ; +#19209 = FACE_OUTER_BOUND ( 'NONE', #35324, .T. ) ; +#19210 = PRESENTATION_STYLE_ASSIGNMENT (( #58080 ) ) ; +#19211 = STYLED_ITEM ( 'NONE', ( #83543 ), #84495 ) ; +#19212 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55121 ) ) ; +#19213 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#19214 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#19215 = SURFACE_STYLE_USAGE ( .BOTH. , #40349 ) ; +#19216 = LINE ( 'NONE', #96311, #45410 ) ; +#19217 = FILL_AREA_STYLE ('',( #50428 ) ) ; +#19218 = ORIENTED_EDGE ( 'NONE', *, *, #5063, .F. ) ; +#19220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74712 ) ) ; +#19219 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#19221 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.300000000000000266, 4.112574283980952083E-79 ) ) ; +#19224 = DIRECTION ( 'NONE', ( -0.6034218327410999505, -0.7974221540510221251, 0.000000000000000000 ) ) ; +#19223 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19222 = AXIS2_PLACEMENT_3D ( 'NONE', #39033, #93598, #94114 ) ; +#19225 = AXIS2_PLACEMENT_3D ( 'NONE', #77299, #6292, #67613 ) ; +#19226 = SURFACE_SIDE_STYLE ('',( #64211 ) ) ; +#19227 = ADVANCED_FACE ( 'NONE', ( #25510 ), #52492, .T. ) ; +#19229 = ORIENTED_EDGE ( 'NONE', *, *, #89997, .T. ) ; +#19228 = AXIS2_PLACEMENT_3D ( 'NONE', #31774, #54795, #8701 ) ; +#19230 = STYLED_ITEM ( 'NONE', ( #68790 ), #62787 ) ; +#19231 = PLANE ( 'NONE', #14556 ) ; +#19232 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#19233 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19234 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19235 = VECTOR ( 'NONE', #66448, 1000.000000000000114 ) ; +#19236 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, 0.000000000000000000 ) ) ; +#19237 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19238 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92604 ), #56828 ) ; +#19239 = CLOSED_SHELL ( 'NONE', ( #61801, #64839, #44646, #11619, #24434, #2054 ) ) ; +#19240 = EDGE_CURVE ( 'NONE', #69281, #1547, #60662, .T. ) ; +#19241 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19242 = VERTEX_POINT ( 'NONE', #67779 ) ; +#19243 = ORIENTED_EDGE ( 'NONE', *, *, #90624, .F. ) ; +#19244 = VECTOR ( 'NONE', #75145, 1000.000000000000000 ) ; +#19245 = PRESENTATION_STYLE_ASSIGNMENT (( #9515 ) ) ; +#19246 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#19247 = ORIENTED_EDGE ( 'NONE', *, *, #42731, .F. ) ; +#19248 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19249 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19250 = PLANE ( 'NONE', #77692 ) ; +#19251 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333315984, -1.699999999999999956, 0.000000000000000000 ) ) ; +#19252 = FACE_OUTER_BOUND ( 'NONE', #11425, .T. ) ; +#19253 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #82185, #53976 ) ; +#19254 = PLANE ( 'NONE', #37864 ) ; +#19255 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#19256 = VECTOR ( 'NONE', #28359, 1000.000000000000000 ) ; +#19258 = ORIENTED_EDGE ( 'NONE', *, *, #13203, .T. ) ; +#19257 = ORIENTED_EDGE ( 'NONE', *, *, #63847, .F. ) ; +#19259 = EDGE_LOOP ( 'NONE', ( #88879, #48384, #89810, #56864 ) ) ; +#19260 = AXIS2_PLACEMENT_3D ( 'NONE', #62965, #39959, #39441 ) ; +#19261 = ORIENTED_EDGE ( 'NONE', *, *, #283, .F. ) ; +#19262 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19263 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36179, 'distance_accuracy_value', 'NONE'); +#19264 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19265 = CARTESIAN_POINT ( 'NONE', ( 0.4157215867521200092, -0.9061895606545929960, 0.8299999999999999600 ) ) ; +#19267 = ORIENTED_EDGE ( 'NONE', *, *, #83467, .T. ) ; +#19268 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49274 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10802, #34404, #47435 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19269 = MANIFOLD_SOLID_BREP ( 'ÊäÈë58', #85940 ) ; +#19270 = ADVANCED_FACE ( 'NONE', ( #29504 ), #90792, .F. ) ; +#19271 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19272 = DIRECTION ( 'NONE', ( -0.7071067811865416886, 0.7071067811865532349, 0.000000000000000000 ) ) ; +#19273 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #14781, .NOT_KNOWN. ) ; +#19274 = ORIENTED_EDGE ( 'NONE', *, *, #72303, .F. ) ; +#19275 = FILL_AREA_STYLE_COLOUR ( '', #72671 ) ; +#19276 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19278 = ORIENTED_EDGE ( 'NONE', *, *, #21728, .T. ) ; +#19277 = AXIS2_PLACEMENT_3D ( 'NONE', #100032, #37872, #54721 ) ; +#19279 = ORIENTED_EDGE ( 'NONE', *, *, #91056, .T. ) ; +#19280 = VERTEX_POINT ( 'NONE', #62184 ) ; +#19281 = FILL_AREA_STYLE ('',( #2978 ) ) ; +#19282 = VECTOR ( 'NONE', #17313, 1000.000000000000000 ) ; +#19284 = FILL_AREA_STYLE ('',( #3973 ) ) ; +#19283 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19285 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#19287 = ORIENTED_EDGE ( 'NONE', *, *, #85565, .T. ) ; +#19286 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#19288 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32479 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75175, #84325, #92457 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19289 = FACE_OUTER_BOUND ( 'NONE', #11103, .T. ) ; +#19290 = VERTEX_POINT ( 'NONE', #70815 ) ; +#19291 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37254 ) ) ; +#19292 = CARTESIAN_POINT ( 'NONE', ( -0.2582749839912160117, -0.9663557550577259736, 0.8100000000000000533 ) ) ; +#19293 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#19294 = ORIENTED_EDGE ( 'NONE', *, *, #68221, .T. ) ; +#19295 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19296 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19297 = ORIENTED_EDGE ( 'NONE', *, *, #19549, .T. ) ; +#19298 = VERTEX_POINT ( 'NONE', #54517 ) ; +#19299 = ADVANCED_FACE ( 'NONE', ( #86644 ), #23877, .T. ) ; +#19301 = PRESENTATION_STYLE_ASSIGNMENT (( #20815 ) ) ; +#19300 = CARTESIAN_POINT ( 'NONE', ( 0.3979805126599459952, -0.9025088801136570416, 0.8299999999999992939 ) ) ; +#19302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95297, #63719, #71868 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19303 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.5000000000000000000, -0.02000000000001675091 ) ) ; +#19304 = ADVANCED_FACE ( 'NONE', ( #85121 ), #38177, .T. ) ; +#19305 = SURFACE_STYLE_FILL_AREA ( #64770 ) ; +#19306 = SURFACE_STYLE_USAGE ( .BOTH. , #89270 ) ; +#19307 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19308 = PRESENTATION_STYLE_ASSIGNMENT (( #96392 ) ) ; +#19309 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, -0.5799999999999999600 ) ) ; +#19310 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6103, 'distance_accuracy_value', 'NONE'); +#19311 = ORIENTED_EDGE ( 'NONE', *, *, #66162, .T. ) ; +#19312 = AXIS2_PLACEMENT_3D ( 'NONE', #84515, #30367, #69153 ) ; +#19313 = EDGE_LOOP ( 'NONE', ( #3320, #26004, #1827, #81774 ) ) ; +#19314 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98231, #21696, #52857 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19315 = SURFACE_SIDE_STYLE ('',( #26006 ) ) ; +#19316 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.699999999999999734, -0.02000000000002724945 ) ) ; +#19317 = CARTESIAN_POINT ( 'NONE', ( 1.186840394175660007, -1.149778012002649952, 0.8100000000000000533 ) ) ; +#19318 = AXIS2_PLACEMENT_3D ( 'NONE', #74879, #91198, #52409 ) ; +#19319 = ADVANCED_FACE ( 'NONE', ( #8948 ), #77456, .T. ) ; +#19320 = VECTOR ( 'NONE', #18622, 1000.000000000000000 ) ; +#19321 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19322 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000533, 0.000000000000000000 ) ) ; +#19323 = STYLED_ITEM ( 'NONE', ( #89519 ), #164 ) ; +#19324 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 5.373192999999999664, 0.8991599999999999593 ) ) ; +#19325 = PLANE ( 'NONE', #41377 ) ; +#19326 = ORIENTED_EDGE ( 'NONE', *, *, #100008, .T. ) ; +#19327 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19328 = CARTESIAN_POINT ( 'NONE', ( 0.9366369866146576628, 0.4412590759269660601, 0.8299999999999999600 ) ) ; +#19329 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#19330 = SURFACE_SIDE_STYLE ('',( #26514 ) ) ; +#19331 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#19332 = CARTESIAN_POINT ( 'NONE', ( 1.387756737235432025, -1.460253732877538457, 0.8099999999997002931 ) ) ; +#19333 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19334 = CARTESIAN_POINT ( 'NONE', ( 7.386066041625060308, 7.678361041625021421, 0.8991599999999999593 ) ) ; +#19335 = EDGE_CURVE ( 'NONE', #97211, #13067, #10962, .T. ) ; +#19336 = PRESENTATION_STYLE_ASSIGNMENT (( #97418 ) ) ; +#19337 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7881 ) ) ; +#19338 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.299999999999999822, -1.507334416018511324E-89 ) ) ; +#19339 = LINE ( 'NONE', #56161, #31037 ) ; +#19340 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19341 = FILL_AREA_STYLE_COLOUR ( '', #11957 ) ; +#19342 = AXIS2_PLACEMENT_3D ( 'NONE', #77628, #62326, #511 ) ; +#19343 = DIRECTION ( 'NONE', ( 0.7071067816865476141, 0.7071067806865475314, 0.000000000000000000 ) ) ; +#19344 = ORIENTED_EDGE ( 'NONE', *, *, #65000, .T. ) ; +#19345 = CARTESIAN_POINT ( 'NONE', ( 1.540061115671039982, -0.9808836469697840288, 0.8299999999999999600 ) ) ; +#19346 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 6.650000000000000355, 0.000000000000000000 ) ) ; +#19347 = ORIENTED_EDGE ( 'NONE', *, *, #73477, .F. ) ; +#19348 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19349 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#19350 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#19351 = SURFACE_STYLE_USAGE ( .BOTH. , #42854 ) ; +#19352 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67512, 'distance_accuracy_value', 'NONE'); +#19353 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42194 ) ) ; +#19354 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1441 ) ) ; +#19355 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8648700000000000276 ) ) ; +#19356 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37314 ) ) ; +#19357 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38902 ), #45414 ) ; +#19358 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19359 = EDGE_CURVE ( 'NONE', #58941, #56090, #96784, .T. ) ; +#19360 = ORIENTED_EDGE ( 'NONE', *, *, #16873, .T. ) ; +#19361 = EDGE_LOOP ( 'NONE', ( #18462, #95599, #11541, #87734 ) ) ; +#19362 = LINE ( 'NONE', #34223, #64600 ) ; +#19363 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.816666666666666652, 0.000000000000000000 ) ) ; +#19364 = VECTOR ( 'NONE', #75299, 1000.000000000000000 ) ; +#19365 = PRESENTATION_STYLE_ASSIGNMENT (( #73002 ) ) ; +#19366 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19367 = CARTESIAN_POINT ( 'NONE', ( -0.4682333997055400099, -1.153630909546540018, 0.8100000000000000533 ) ) ; +#19368 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19369 = LINE ( 'NONE', #25058, #94149 ) ; +#19370 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#19371 = EDGE_CURVE ( 'NONE', #64267, #82810, #63684, .T. ) ; +#19373 = PLANE ( 'NONE', #100459 ) ; +#19372 = VECTOR ( 'NONE', #25330, 999.9999999999998863 ) ; +#19374 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19375 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19376 = ORIENTED_EDGE ( 'NONE', *, *, #38880, .T. ) ; +#19377 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#19378 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79760 ) ) ; +#19379 = VERTEX_POINT ( 'NONE', #89164 ) ; +#19380 = SURFACE_SIDE_STYLE ('',( #36726 ) ) ; +#19381 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19382 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, -8.400000000000000355, -13.54999999999999893 ) ) ; +#19383 = LINE ( 'NONE', #97936, #33629 ) ; +#19384 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19385 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19386 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8648700000000000276 ) ) ; +#19387 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19388 = CARTESIAN_POINT ( 'NONE', ( -0.4123911155665859751, -0.9468660869752939524, 0.8100000000000000533 ) ) ; +#19389 = PLANE ( 'NONE', #92072 ) ; +#19390 = STYLED_ITEM ( 'NONE', ( #30249 ), #63396 ) ; +#19392 = ORIENTED_EDGE ( 'NONE', *, *, #4455, .F. ) ; +#19391 = ORIENTED_EDGE ( 'NONE', *, *, #64786, .T. ) ; +#19393 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19394 = LINE ( 'NONE', #2576, #45154 ) ; +#19395 = VECTOR ( 'NONE', #91078, 1000.000000000000000 ) ; +#19396 = ORIENTED_EDGE ( 'NONE', *, *, #72811, .T. ) ; +#19397 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#19398 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19399 = CIRCLE ( 'NONE', #79768, 0.1999999999999996503 ) ; +#19400 = EDGE_LOOP ( 'NONE', ( #85719, #87329, #65449, #96650 ) ) ; +#19401 = ORIENTED_EDGE ( 'NONE', *, *, #38808, .F. ) ; +#19402 = SURFACE_SIDE_STYLE ('',( #58255 ) ) ; +#19403 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#19404 = LINE ( 'NONE', #2589, #39829 ) ; +#19405 = LINE ( 'NONE', #58749, #43776 ) ; +#19406 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#19408 = ORIENTED_EDGE ( 'NONE', *, *, #2643, .T. ) ; +#19407 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100822 ) ) ; +#19409 = VERTEX_POINT ( 'NONE', #64673 ) ; +#19410 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8648700000000000276 ) ) ; +#19411 = EDGE_CURVE ( 'NONE', #19154, #31700, #51002, .T. ) ; +#19412 = ORIENTED_EDGE ( 'NONE', *, *, #90697, .T. ) ; +#19413 = ADVANCED_FACE ( 'NONE', ( #95271 ), #80508, .F. ) ; +#19414 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#19415 = AXIS2_PLACEMENT_3D ( 'NONE', #56450, #24289, #71735 ) ; +#19416 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79542, #17722, #24943, #9506 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#19417 = SURFACE_SIDE_STYLE ('',( #87857 ) ) ; +#19420 = ORIENTED_EDGE ( 'NONE', *, *, #50805, .F. ) ; +#19419 = VECTOR ( 'NONE', #26544, 1000.000000000000000 ) ; +#19418 = PRESENTATION_STYLE_ASSIGNMENT (( #89862 ) ) ; +#19421 = SURFACE_SIDE_STYLE ('',( #82231 ) ) ; +#19422 = ORIENTED_EDGE ( 'NONE', *, *, #46325, .F. ) ; +#19423 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19424 = VERTEX_POINT ( 'NONE', #17678 ) ; +#19425 = ADVANCED_FACE ( 'NONE', ( #57547 ), #34055, .T. ) ; +#19426 = SURFACE_STYLE_USAGE ( .BOTH. , #81745 ) ; +#19427 = ORIENTED_EDGE ( 'NONE', *, *, #11225, .F. ) ; +#19428 = LINE ( 'NONE', #89873, #10515 ) ; +#19429 = ADVANCED_FACE ( 'NONE', ( #4381 ), #60058, .T. ) ; +#19430 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#19431 = STYLED_ITEM ( 'NONE', ( #42236 ), #32408 ) ; +#19432 = CARTESIAN_POINT ( 'NONE', ( -1.367649144690350038, -1.097307480365639965, 0.8300000000000000711 ) ) ; +#19433 = ADVANCED_FACE ( 'NONE', ( #74347 ), #91645, .T. ) ; +#19434 = FACE_OUTER_BOUND ( 'NONE', #89962, .T. ) ; +#19435 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#19436 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, 0.000000000000000000 ) ) ; +#19437 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48830 ) ) ; +#19439 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#19438 = SURFACE_STYLE_USAGE ( .BOTH. , #10678 ) ; +#19440 = STYLED_ITEM ( 'NONE', ( #24914 ), #31764 ) ; +#19441 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#19442 = VERTEX_POINT ( 'NONE', #27383 ) ; +#19443 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 1.699999999999999956, 3.495651678170121160E-76 ) ) ; +#19444 = ORIENTED_EDGE ( 'NONE', *, *, #8397, .T. ) ; +#19446 = FILL_AREA_STYLE_COLOUR ( '', #64360 ) ; +#19445 = AXIS2_PLACEMENT_3D ( 'NONE', #82470, #28820, #67119 ) ; +#19447 = CARTESIAN_POINT ( 'NONE', ( -0.2130180398314890089, -1.488490865982160294, 0.8100000000000000533 ) ) ; +#19448 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19449 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21054 ) ) ; +#19451 = ADVANCED_FACE ( 'NONE', ( #59575 ), #20710, .F. ) ; +#19450 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, 0.000000000000000000 ) ) ; +#19452 = SURFACE_STYLE_USAGE ( .BOTH. , #97533 ) ; +#19453 = SHAPE_REPRESENTATION ( 'ipx3.xtd', ( #82894 ), #28905 ) ; +#19455 = FILL_AREA_STYLE ('',( #11196 ) ) ; +#19454 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42502 ), #81445 ) ; +#19456 = PLANE ( 'NONE', #7849 ) ; +#19457 = CARTESIAN_POINT ( 'NONE', ( 1.785976973916959976, -1.116141175150469955, 0.8100000000000000533 ) ) ; +#19458 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11200 ) ) ; +#19459 = MANIFOLD_SOLID_BREP ( 'ÊäÈë84', #61626 ) ; +#19460 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64682 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65219, #96836, #25945 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19461 = EDGE_CURVE ( 'NONE', #73012, #36610, #45166, .T. ) ; +#19462 = SURFACE_SIDE_STYLE ('',( #89403 ) ) ; +#19463 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19464 = CIRCLE ( 'NONE', #89580, 0.04999999999999991257 ) ; +#19465 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19466 = ORIENTED_EDGE ( 'NONE', *, *, #54299, .F. ) ; +#19467 = EDGE_CURVE ( 'NONE', #80708, #55259, #23241, .T. ) ; +#19468 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81457 ) ) ; +#19469 = EDGE_CURVE ( 'NONE', #92811, #29149, #53367, .T. ) ; +#19470 = FILL_AREA_STYLE ('',( #58316 ) ) ; +#19471 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19472 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19473 = EDGE_CURVE ( 'NONE', #28089, #77757, #51074, .T. ) ; +#19474 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35062 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98354, #97870, #90778 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19475 = VERTEX_POINT ( 'NONE', #46686 ) ; +#19476 = PLANE ( 'NONE', #100927 ) ; +#19477 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19478 = SURFACE_STYLE_USAGE ( .BOTH. , #81299 ) ; +#19479 = LINE ( 'NONE', #2663, #71417 ) ; +#19480 = LINE ( 'NONE', #41469, #66539 ) ; +#19481 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#19482 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.000000000000000000 ) ) ; +#19483 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 1.668003342285390072E-16 ) ) ; +#19484 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#19485 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19486 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000057288, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#19487 = EDGE_CURVE ( 'NONE', #63592, #76538, #69131, .T. ) ; +#19488 = ORIENTED_EDGE ( 'NONE', *, *, #93495, .F. ) ; +#19489 = ORIENTED_EDGE ( 'NONE', *, *, #83314, .F. ) ; +#19490 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19491 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73487, 'distance_accuracy_value', 'NONE'); +#19492 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98145, 'distance_accuracy_value', 'NONE'); +#19493 = CARTESIAN_POINT ( 'NONE', ( 0.4725911777878056275, -1.227340210498138795, 0.8100000000000001643 ) ) ; +#19494 = FACE_OUTER_BOUND ( 'NONE', #77026, .T. ) ; +#19495 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959499, 0.000000000000000000 ) ) ; +#19496 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000004441, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#19497 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19498 = ORIENTED_EDGE ( 'NONE', *, *, #10324, .T. ) ; +#19499 = EDGE_CURVE ( 'NONE', #30965, #23968, #77851, .T. ) ; +#19500 = FILL_AREA_STYLE ('',( #3177 ) ) ; +#19501 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55087, #41758, #16211, #86188 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#19502 = VERTEX_POINT ( 'NONE', #740 ) ; +#19503 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19504 = ORIENTED_EDGE ( 'NONE', *, *, #28732, .F. ) ; +#19505 = EDGE_CURVE ( 'NONE', #85949, #951, #23743, .T. ) ; +#19506 = FILL_AREA_STYLE ('',( #88448 ) ) ; +#19507 = VECTOR ( 'NONE', #88741, 1000.000000000000000 ) ; +#19508 = VECTOR ( 'NONE', #16238, 1000.000000000000000 ) ; +#19509 = PRESENTATION_STYLE_ASSIGNMENT (( #50688 ) ) ; +#19510 = PRESENTATION_STYLE_ASSIGNMENT (( #81825 ) ) ; +#19511 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19512 = LINE ( 'NONE', #67950, #59411 ) ; +#19513 = ORIENTED_EDGE ( 'NONE', *, *, #1104, .T. ) ; +#19514 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4840 ), #39049 ) ; +#19515 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78197 ) ) ; +#19516 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11263 ) ) ; +#19517 = ORIENTED_EDGE ( 'NONE', *, *, #60484, .F. ) ; +#19518 = SURFACE_STYLE_FILL_AREA ( #80321 ) ; +#19519 = STYLED_ITEM ( 'NONE', ( #47732 ), #81379 ) ; +#19520 = ORIENTED_EDGE ( 'NONE', *, *, #15798, .F. ) ; +#19521 = EDGE_LOOP ( 'NONE', ( #86611, #74314, #86960, #54074 ) ) ; +#19522 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#19523 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19524 = AXIS2_PLACEMENT_3D ( 'NONE', #89909, #27659, #76590 ) ; +#19525 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19527 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998898659, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#19526 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.600000000000000089, -13.54999999999999893 ) ) ; +#19528 = ORIENTED_EDGE ( 'NONE', *, *, #55635, .T. ) ; +#19530 = ORIENTED_EDGE ( 'NONE', *, *, #51746, .T. ) ; +#19529 = ORIENTED_EDGE ( 'NONE', *, *, #54093, .T. ) ; +#19531 = EDGE_CURVE ( 'NONE', #14220, #80977, #39057, .T. ) ; +#19532 = ORIENTED_EDGE ( 'NONE', *, *, #94401, .F. ) ; +#19533 = EDGE_CURVE ( 'NONE', #18285, #98956, #10191, .T. ) ; +#19534 = VECTOR ( 'NONE', #55643, 1000.000000000000000 ) ; +#19535 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89657 ), #52140 ) ; +#19536 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#19537 = EDGE_LOOP ( 'NONE', ( #82579, #21274, #51098, #6384 ) ) ; +#19538 = ORIENTED_EDGE ( 'NONE', *, *, #55237, .T. ) ; +#19539 = STYLED_ITEM ( 'NONE', ( #87528 ), #42647 ) ; +#19540 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19541 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#19542 = DIRECTION ( 'NONE', ( -1.000000000000000000, 2.168404344971010051E-15, 0.000000000000000000 ) ) ; +#19543 = VERTEX_POINT ( 'NONE', #76326 ) ; +#19544 = FACE_OUTER_BOUND ( 'NONE', #50709, .T. ) ; +#19545 = SURFACE_SIDE_STYLE ('',( #81860 ) ) ; +#19546 = EDGE_LOOP ( 'NONE', ( #49434, #93969, #93720, #83079 ) ) ; +#19547 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19548 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000089, 2.676179938779915002, -0.02000000000000000042 ) ) ; +#19549 = EDGE_CURVE ( 'NONE', #58119, #7813, #37559, .T. ) ; +#19551 = AXIS2_PLACEMENT_3D ( 'NONE', #9146, #100019, #61374 ) ; +#19550 = FACE_OUTER_BOUND ( 'NONE', #97349, .T. ) ; +#19552 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63607 ), #96206 ) ; +#19553 = LINE ( 'NONE', #10286, #71468 ) ; +#19554 = ADVANCED_FACE ( 'NONE', ( #79890 ), #56922, .T. ) ; +#19555 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#19556 = STYLED_ITEM ( 'NONE', ( #73865 ), #9987 ) ; +#19557 = CARTESIAN_POINT ( 'NONE', ( 1.719030235149860086, -1.443664018207750033, 0.8299999999999999600 ) ) ; +#19558 = SURFACE_SIDE_STYLE ('',( #89520 ) ) ; +#19559 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#19560 = EDGE_LOOP ( 'NONE', ( #72272, #2484, #41403, #23081, #83329, #23803, #73325, #83665 ) ) ; +#19561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50049 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90075, #20118, #35488 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19562 = FACE_OUTER_BOUND ( 'NONE', #65390, .T. ) ; +#19563 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#19564 = CARTESIAN_POINT ( 'NONE', ( 1.441396927522579974, -1.330101555947649894, 0.8300000000000022915 ) ) ; +#19565 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19566 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -2.300000000000000266, 0.000000000000000000 ) ) ; +#19567 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19568 = SURFACE_STYLE_FILL_AREA ( #58422 ) ; +#19569 = EDGE_CURVE ( 'NONE', #51183, #52485, #99895, .T. ) ; +#19570 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89693 ), #60353 ) ; +#19571 = CARTESIAN_POINT ( 'NONE', ( 6.212268750249974936, 10.39365124975002530, 0.8991599999999999593 ) ) ; +#19572 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#19573 = VERTEX_POINT ( 'NONE', #78857 ) ; +#19574 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19575 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#19576 = VECTOR ( 'NONE', #28839, 1000.000000000000000 ) ; +#19577 = VECTOR ( 'NONE', #92715, 999.9999999999998863 ) ; +#19578 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.9000000000000007994, 0.000000000000000000 ) ) ; +#19579 = EDGE_LOOP ( 'NONE', ( #15179, #67601, #34929 ) ) ; +#19580 = AXIS2_PLACEMENT_3D ( 'NONE', #17814, #55657, #71964 ) ; +#19581 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19582 = ADVANCED_FACE ( 'NONE', ( #79371 ), #87526, .T. ) ; +#19583 = CARTESIAN_POINT ( 'NONE', ( -0.2409735724455049910, -1.328064047174219997, 0.8100000000000000533 ) ) ; +#19584 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19585 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19587 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55485 ) ) ; +#19588 = VERTEX_POINT ( 'NONE', #72713 ) ; +#19589 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19590 = FILL_AREA_STYLE ('',( #28272 ) ) ; +#19591 = FACE_OUTER_BOUND ( 'NONE', #9450, .T. ) ; +#19592 = LINE ( 'NONE', #57420, #8457 ) ; +#19593 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19594 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19595 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6483 ) ) ; +#19596 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#19597 = VECTOR ( 'NONE', #25155, 1000.000000000000000 ) ; +#19598 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#19599 = FACE_OUTER_BOUND ( 'NONE', #6424, .T. ) ; +#19600 = FILL_AREA_STYLE ('',( #76224 ) ) ; +#19601 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39932, 'distance_accuracy_value', 'NONE'); +#19602 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19603 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#19604 = EDGE_CURVE ( 'NONE', #13170, #58620, #96167, .T. ) ; +#19605 = SURFACE_STYLE_USAGE ( .BOTH. , #43085 ) ; +#19606 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19607 = ORIENTED_EDGE ( 'NONE', *, *, #93471, .T. ) ; +#19608 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#19609 = VERTEX_POINT ( 'NONE', #73234 ) ; +#19610 = FILL_AREA_STYLE_COLOUR ( '', #28965 ) ; +#19612 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17124, 'distance_accuracy_value', 'NONE'); +#19611 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57308 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10021, #57627, #9535 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19613 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61834, 'distance_accuracy_value', 'NONE'); +#19614 = STYLED_ITEM ( 'NONE', ( #75237 ), #42859 ) ; +#19615 = LINE ( 'NONE', #4782, #81439 ) ; +#19616 = PRESENTATION_STYLE_ASSIGNMENT (( #89573 ) ) ; +#19617 = CARTESIAN_POINT ( 'NONE', ( 2.676179938779915002, 3.099999999999960121, 0.000000000000000000 ) ) ; +#19618 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666667052, 2.700000000000000178, 0.000000000000000000 ) ) ; +#19619 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19620 = EDGE_LOOP ( 'NONE', ( #55507, #8617, #7146, #96866 ) ) ; +#19621 = ADVANCED_FACE ( 'NONE', ( #3273 ), #34439, .T. ) ; +#19622 = MANIFOLD_SOLID_BREP ( 'ÊäÈë39', #97430 ) ; +#19623 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000533, 0.000000000000000000 ) ) ; +#19624 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89751, 'distance_accuracy_value', 'NONE'); +#19625 = AXIS2_PLACEMENT_3D ( 'NONE', #2966, #10016, #3474 ) ; +#19626 = LINE ( 'NONE', #36468, #19395 ) ; +#19627 = VERTEX_POINT ( 'NONE', #58940 ) ; +#19628 = DIRECTION ( 'NONE', ( 1.291173436397889936E-79, -1.000000000000000000, 5.992048669697412538E-127 ) ) ; +#19629 = EDGE_CURVE ( 'NONE', #68437, #98020, #100456, .T. ) ; +#19630 = VECTOR ( 'NONE', #84029, 1000.000000000000000 ) ; +#19631 = SURFACE_STYLE_USAGE ( .BOTH. , #27310 ) ; +#19632 = CARTESIAN_POINT ( 'NONE', ( 1.440857328897279910, -1.359907766992060285, 0.8299999999999994049 ) ) ; +#19633 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19634 = CARTESIAN_POINT ( 'NONE', ( -1.191485992818250184, -1.440849955440170138, 0.8299999999999999600 ) ) ; +#19635 = ADVANCED_FACE ( 'NONE', ( #30608 ), #66062, .T. ) ; +#19636 = ORIENTED_EDGE ( 'NONE', *, *, #93644, .F. ) ; +#19637 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19638 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19639 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79918, 'distance_accuracy_value', 'NONE'); +#19640 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19641 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#19642 = EDGE_CURVE ( 'NONE', #85096, #75181, #74464, .T. ) ; +#19643 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#19644 = VERTEX_POINT ( 'NONE', #20581 ) ; +#19645 = PLANE ( 'NONE', #59582 ) ; +#19646 = SURFACE_STYLE_FILL_AREA ( #89598 ) ; +#19647 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66939 ), #91430 ) ; +#19648 = VECTOR ( 'NONE', #81578, 1000.000000000000000 ) ; +#19649 = FILL_AREA_STYLE_COLOUR ( '', #5386 ) ; +#19650 = VERTEX_POINT ( 'NONE', #493 ) ; +#19651 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#19653 = ADVANCED_FACE ( 'NONE', ( #31643 ), #24019, .T. ) ; +#19652 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #81294 ) ; +#19654 = EDGE_CURVE ( 'NONE', #54104, #9920, #23499, .T. ) ; +#19655 = VECTOR ( 'NONE', #17521, 1000.000000000000000 ) ; +#19656 = VECTOR ( 'NONE', #76298, 1000.000000000000000 ) ; +#19657 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78336 ), #1749 ) ; +#19658 = EDGE_CURVE ( 'NONE', #68615, #11665, #54656, .T. ) ; +#19659 = ORIENTED_EDGE ( 'NONE', *, *, #60717, .F. ) ; +#19660 = ADVANCED_FACE ( 'NONE', ( #40841 ), #39296, .T. ) ; +#19663 = ORIENTED_EDGE ( 'NONE', *, *, #65738, .F. ) ; +#19662 = FILL_AREA_STYLE_COLOUR ( '', #99636 ) ; +#19661 = AXIS2_PLACEMENT_3D ( 'NONE', #37975, #91581, #85933 ) ; +#19664 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6542 ), #68538 ) ; +#19665 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19666 = STYLED_ITEM ( 'NONE', ( #54584 ), #81880 ) ; +#19667 = FILL_AREA_STYLE_COLOUR ( '', #97605 ) ; +#19668 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19669 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#19670 = PLANE ( 'NONE', #14886 ) ; +#19671 = ORIENTED_EDGE ( 'NONE', *, *, #7344, .F. ) ; +#19672 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19673 = EDGE_CURVE ( 'NONE', #312, #7985, #1011, .T. ) ; +#19674 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#19675 = ORIENTED_EDGE ( 'NONE', *, *, #38247, .F. ) ; +#19676 = AXIS2_PLACEMENT_3D ( 'NONE', #17564, #57950, #9349 ) ; +#19677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19678 = ORIENTED_EDGE ( 'NONE', *, *, #45406, .T. ) ; +#19679 = EDGE_CURVE ( 'NONE', #17377, #36766, #17314, .T. ) ; +#19680 = LINE ( 'NONE', #34532, #12347 ) ; +#19681 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#19682 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42508 ), #76734 ) ; +#19683 = FILL_AREA_STYLE ('',( #88135 ) ) ; +#19684 = EDGE_LOOP ( 'NONE', ( #40750, #34630, #27346, #75840 ) ) ; +#19685 = VECTOR ( 'NONE', #6162, 1000.000000000000000 ) ; +#19686 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#19687 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#19688 = ORIENTED_EDGE ( 'NONE', *, *, #42991, .F. ) ; +#19689 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19690 = ORIENTED_EDGE ( 'NONE', *, *, #93785, .F. ) ; +#19691 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#19693 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19692 = FACE_BOUND ( 'NONE', #15853, .T. ) ; +#19694 = CARTESIAN_POINT ( 'NONE', ( -1.078436373535740067, -1.243129529655299992, 0.8299999999999999600 ) ) ; +#19695 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19696 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19697 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#19698 = FILL_AREA_STYLE_COLOUR ( '', #95190 ) ; +#19699 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16447 ) ) ; +#19700 = SURFACE_STYLE_FILL_AREA ( #49861 ) ; +#19701 = CARTESIAN_POINT ( 'NONE', ( 1.209440659729950074, -0.9548508715965590143, 0.8299999999999999600 ) ) ; +#19702 = VERTEX_POINT ( 'NONE', #2026 ) ; +#19703 = FILL_AREA_STYLE_COLOUR ( '', #40421 ) ; +#19704 = FACE_OUTER_BOUND ( 'NONE', #28057, .T. ) ; +#19705 = EDGE_CURVE ( 'NONE', #3141, #75293, #61807, .T. ) ; +#19707 = LINE ( 'NONE', #42690, #99461 ) ; +#19706 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#19708 = SURFACE_STYLE_USAGE ( .BOTH. , #99097 ) ; +#19709 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.383333333333326642, 1.747825839084889375E-76 ) ) ; +#19710 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#19711 = LINE ( 'NONE', #20196, #59903 ) ; +#19712 = FACE_OUTER_BOUND ( 'NONE', #95241, .T. ) ; +#19713 = EDGE_CURVE ( 'NONE', #60733, #90974, #76781, .T. ) ; +#19714 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, 0.000000000000000000 ) ) ; +#19715 = ORIENTED_EDGE ( 'NONE', *, *, #25871, .F. ) ; +#19716 = PLANE ( 'NONE', #71734 ) ; +#19717 = FILL_AREA_STYLE ('',( #25893 ) ) ; +#19718 = SURFACE_SIDE_STYLE ('',( #4874 ) ) ; +#19719 = CARTESIAN_POINT ( 'NONE', ( 11.79841250049994983, 7.155102500499952001, 0.8991599999999999593 ) ) ; +#19720 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1458578643762690474 ) ) ; +#19721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19722 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55676 ), #60560 ) ; +#19723 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44189 ), #88170 ) ; +#19724 = SURFACE_SIDE_STYLE ('',( #2402 ) ) ; +#19725 = PRESENTATION_STYLE_ASSIGNMENT (( #49891 ) ) ; +#19726 = PRESENTATION_STYLE_ASSIGNMENT (( #21717 ) ) ; +#19727 = PLANE ( 'NONE', #5980 ) ; +#19728 = LINE ( 'NONE', #26903, #5441 ) ; +#19729 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19730 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19731 = PRESENTATION_STYLE_ASSIGNMENT (( #28399 ) ) ; +#19732 = EDGE_CURVE ( 'NONE', #64125, #55021, #57184, .T. ) ; +#19733 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19734 = SURFACE_STYLE_FILL_AREA ( #59591 ) ; +#19735 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60496 ), #32777 ) ; +#19736 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19737 = FACE_OUTER_BOUND ( 'NONE', #27983, .T. ) ; +#19738 = STYLED_ITEM ( 'NONE', ( #82498 ), #94544 ) ; +#19739 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#19740 = PLANE ( 'NONE', #40619 ) ; +#19741 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #9012, 'design' ) ; +#19742 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19743 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#19744 = ORIENTED_EDGE ( 'NONE', *, *, #66115, .T. ) ; +#19745 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19746 = EDGE_CURVE ( 'NONE', #44849, #16114, #66325, .T. ) ; +#19747 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88265 ) ) ; +#19748 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19749 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47743, 'distance_accuracy_value', 'NONE'); +#19750 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19751 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97651, 'distance_accuracy_value', 'NONE'); +#19753 = FILL_AREA_STYLE ('',( #91680 ) ) ; +#19752 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19754 = STYLED_ITEM ( 'NONE', ( #58949 ), #65696 ) ; +#19755 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19756 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#19757 = LINE ( 'NONE', #5395, #87490 ) ; +#19758 = STYLED_ITEM ( 'NONE', ( #58436 ), #64839 ) ; +#19759 = VERTEX_POINT ( 'NONE', #33686 ) ; +#19760 = VECTOR ( 'NONE', #1979, 1000.000000000000000 ) ; +#19761 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19762 = AXIS2_PLACEMENT_3D ( 'NONE', #29087, #44370, #50586 ) ; +#19763 = CARTESIAN_POINT ( 'NONE', ( 5.971852916749958773, 6.264148083250120180, 0.8648700000000000276 ) ) ; +#19764 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19689, 'distance_accuracy_value', 'NONE'); +#19765 = FILL_AREA_STYLE_COLOUR ( '', #34811 ) ; +#19766 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65267, 'distance_accuracy_value', 'NONE'); +#19767 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19768 = STYLED_ITEM ( 'NONE', ( #66764 ), #75756 ) ; +#19769 = ORIENTED_EDGE ( 'NONE', *, *, #95571, .F. ) ; +#19770 = ORIENTED_EDGE ( 'NONE', *, *, #84441, .F. ) ; +#19771 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#19772 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#19773 = ORIENTED_EDGE ( 'NONE', *, *, #21441, .F. ) ; +#19775 = CARTESIAN_POINT ( 'NONE', ( 1.821320548784939986, -1.306448053922619978, 0.8100000000000000533 ) ) ; +#19774 = AXIS2_PLACEMENT_3D ( 'NONE', #93760, #32555, #39176 ) ; +#19776 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#19777 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19778 = VECTOR ( 'NONE', #77661, 1000.000000000000000 ) ; +#19779 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #94182, #58257 ) ; +#19780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19782 = VERTEX_POINT ( 'NONE', #51025 ) ; +#19781 = VERTEX_POINT ( 'NONE', #41347 ) ; +#19783 = ORIENTED_EDGE ( 'NONE', *, *, #32197, .F. ) ; +#19784 = ORIENTED_EDGE ( 'NONE', *, *, #3133, .F. ) ; +#19785 = EDGE_CURVE ( 'NONE', #87484, #1626, #57695, .T. ) ; +#19786 = CARTESIAN_POINT ( 'NONE', ( 1.877682030168900118, -1.070769809704489983, 0.8299999999999995159 ) ) ; +#19787 = SURFACE_STYLE_USAGE ( .BOTH. , #10503 ) ; +#19789 = SURFACE_STYLE_FILL_AREA ( #81601 ) ; +#19788 = LINE ( 'NONE', #6405, #13300 ) ; +#19790 = VERTEX_POINT ( 'NONE', #72453 ) ; +#19791 = MANIFOLD_SOLID_BREP ( 'ÊäÈë140', #87626 ) ; +#19792 = LINE ( 'NONE', #65761, #77623 ) ; +#19793 = CARTESIAN_POINT ( 'NONE', ( 13.17837699999999934, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#19794 = ADVANCED_FACE ( 'NONE', ( #3543 ), #11097, .F. ) ; +#19795 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58975 ) ) ; +#19796 = ORIENTED_EDGE ( 'NONE', *, *, #78899, .F. ) ; +#19798 = SURFACE_SIDE_STYLE ('',( #11037 ) ) ; +#19797 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19799 = ORIENTED_EDGE ( 'NONE', *, *, #24316, .T. ) ; +#19800 = VERTEX_POINT ( 'NONE', #56682 ) ; +#19801 = EDGE_CURVE ( 'NONE', #52994, #18739, #88300, .T. ) ; +#19802 = VECTOR ( 'NONE', #51545, 999.9999999999998863 ) ; +#19803 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#19804 = FILL_AREA_STYLE ('',( #89737 ) ) ; +#19805 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8648700000000000276 ) ) ; +#19807 = VERTEX_POINT ( 'NONE', #3028 ) ; +#19806 = LINE ( 'NONE', #50971, #72133 ) ; +#19808 = FILL_AREA_STYLE ('',( #83609 ) ) ; +#19809 = ORIENTED_EDGE ( 'NONE', *, *, #43447, .F. ) ; +#19810 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19812 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19813 = EDGE_LOOP ( 'NONE', ( #57493, #15599, #52715, #15623 ) ) ; +#19815 = FILL_AREA_STYLE ('',( #58152 ) ) ; +#19814 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19816 = SURFACE_STYLE_USAGE ( .BOTH. , #67265 ) ; +#19817 = EDGE_LOOP ( 'NONE', ( #92369, #71424, #56125, #53773, #14229, #80418 ) ) ; +#19818 = ORIENTED_EDGE ( 'NONE', *, *, #25421, .T. ) ; +#19819 = PLANE ( 'NONE', #76444 ) ; +#19820 = CYLINDRICAL_SURFACE ( 'NONE', #15506, 1.319494420477459906 ) ; +#19821 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26326 ), #94784 ) ; +#19822 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#19823 = VECTOR ( 'NONE', #67919, 1000.000000000000000 ) ; +#19824 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19825 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19826 = FILL_AREA_STYLE_COLOUR ( '', #99712 ) ; +#19827 = FACE_OUTER_BOUND ( 'NONE', #90235, .T. ) ; +#19828 = ORIENTED_EDGE ( 'NONE', *, *, #61314, .T. ) ; +#19829 = EDGE_LOOP ( 'NONE', ( #52913, #48125, #71144, #11907 ) ) ; +#19830 = VECTOR ( 'NONE', #8278, 1000.000000000000000 ) ; +#19831 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#19832 = CARTESIAN_POINT ( 'NONE', ( 1.406489741257900050, -1.236164603532529993, 0.8100000000000000533 ) ) ; +#19833 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#19834 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19835 = SURFACE_SIDE_STYLE ('',( #35186 ) ) ; +#19836 = EDGE_CURVE ( 'NONE', #25280, #40392, #29417, .T. ) ; +#19837 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19838 = SURFACE_STYLE_FILL_AREA ( #83134 ) ; +#19839 = ORIENTED_EDGE ( 'NONE', *, *, #60616, .F. ) ; +#19840 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19841 = CARTESIAN_POINT ( 'NONE', ( 0.1751932085031089881, -1.046109390704299980, 0.8299999999999999600 ) ) ; +#19842 = SURFACE_STYLE_USAGE ( .BOTH. , #50015 ) ; +#19843 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49222 ), #44301 ) ; +#19844 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19845 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#19846 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18204 ), #36194 ) ; +#19847 = FILL_AREA_STYLE_COLOUR ( '', #68446 ) ; +#19848 = SURFACE_STYLE_USAGE ( .BOTH. , #98377 ) ; +#19849 = SURFACE_STYLE_USAGE ( .BOTH. , #89788 ) ; +#19850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19852 = STYLED_ITEM ( 'NONE', ( #26701 ), #45734 ) ; +#19851 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#19853 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19854 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#19855 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11484, 'distance_accuracy_value', 'NONE'); +#19856 = ORIENTED_EDGE ( 'NONE', *, *, #87077, .T. ) ; +#19857 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#19858 = ORIENTED_EDGE ( 'NONE', *, *, #72342, .T. ) ; +#19859 = SURFACE_STYLE_FILL_AREA ( #89314 ) ; +#19860 = PRESENTATION_STYLE_ASSIGNMENT (( #89802 ) ) ; +#19861 = EDGE_CURVE ( 'NONE', #43003, #32845, #82190, .T. ) ; +#19862 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8648700000000000276 ) ) ; +#19863 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11608 ) ) ; +#19864 = VECTOR ( 'NONE', #14696, 1000.000000000000114 ) ; +#19865 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#19866 = AXIS2_PLACEMENT_3D ( 'NONE', #59325, #52144, #6589 ) ; +#19867 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9591 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96312, #3434, #96810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19868 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#19869 = ORIENTED_EDGE ( 'NONE', *, *, #47223, .F. ) ; +#19870 = ORIENTED_EDGE ( 'NONE', *, *, #40656, .T. ) ; +#19871 = FACE_OUTER_BOUND ( 'NONE', #65891, .T. ) ; +#19872 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34510 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56495, #72785, #2838 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19873 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19874 = CARTESIAN_POINT ( 'NONE', ( -0.4458598713506949918, -1.104165518103240151, 0.8100000000000000533 ) ) ; +#19875 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65869, 'distance_accuracy_value', 'NONE'); +#19876 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#19877 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#19878 = VECTOR ( 'NONE', #77407, 1000.000000000000000 ) ; +#19879 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40616, 'distance_accuracy_value', 'NONE'); +#19880 = LINE ( 'NONE', #19370, #69018 ) ; +#19881 = ADVANCED_FACE ( 'NONE', ( #5486 ), #21857, .T. ) ; +#19882 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19883 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86791 ), #6736 ) ; +#19884 = FILL_AREA_STYLE ('',( #75027 ) ) ; +#19885 = EDGE_LOOP ( 'NONE', ( #84719, #69710, #47083, #88491 ) ) ; +#19886 = LINE ( 'NONE', #88831, #74844 ) ; +#19887 = STYLED_ITEM ( 'NONE', ( #4039 ), #66378 ) ; +#19888 = ORIENTED_EDGE ( 'NONE', *, *, #54239, .F. ) ; +#19889 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#19890 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#19891 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#19892 = FILL_AREA_STYLE ('',( #10116 ) ) ; +#19893 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5839 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49268, #74252, #19101 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19894 = CARTESIAN_POINT ( 'NONE', ( -0.5070681596463531005, -0.9026237492037839649, 0.8299999999999999600 ) ) ; +#19895 = CARTESIAN_POINT ( 'NONE', ( -1.293366770995789894, -1.052467830684129968, 0.8100000000000000533 ) ) ; +#19896 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#19898 = ORIENTED_EDGE ( 'NONE', *, *, #100440, .T. ) ; +#19897 = VERTEX_POINT ( 'NONE', #52510 ) ; +#19899 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93245 ) ) ; +#19900 = FILL_AREA_STYLE ('',( #89843 ) ) ; +#19901 = VERTEX_POINT ( 'NONE', #4515 ) ; +#19902 = EDGE_CURVE ( 'NONE', #89960, #8413, #83657, .T. ) ; +#19903 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333315984, -2.100000000000000089, 0.000000000000000000 ) ) ; +#19905 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19904 = LINE ( 'NONE', #97481, #27824 ) ; +#19906 = ORIENTED_EDGE ( 'NONE', *, *, #88184, .T. ) ; +#19907 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21497 ), #73691 ) ; +#19908 = ORIENTED_EDGE ( 'NONE', *, *, #41235, .T. ) ; +#19909 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19910 = FILL_AREA_STYLE_COLOUR ( '', #49630 ) ; +#19911 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50917 ) ) ; +#19912 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#19913 = PLANE ( 'NONE', #24750 ) ; +#19914 = VERTEX_POINT ( 'NONE', #5971 ) ; +#19915 = VERTEX_POINT ( 'NONE', #29518 ) ; +#19916 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19917 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#19918 = VERTEX_POINT ( 'NONE', #20854 ) ; +#19919 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#19920 = ADVANCED_FACE ( 'NONE', ( #5002 ), #82646, .T. ) ; +#19921 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#19922 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99536, #44478, #45967 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#19924 = ORIENTED_EDGE ( 'NONE', *, *, #82163, .F. ) ; +#19923 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#19925 = LINE ( 'NONE', #11663, #59624 ) ; +#19926 = CARTESIAN_POINT ( 'NONE', ( 1.901147915587950044, -1.336905478629369926, 0.8099999999999996092 ) ) ; +#19927 = VERTEX_POINT ( 'NONE', #28516 ) ; +#19928 = CARTESIAN_POINT ( 'NONE', ( -0.08371903756181429956, -1.220939016933670018, 0.8299999999999999600 ) ) ; +#19929 = PLANE ( 'NONE', #88482 ) ; +#19930 = ORIENTED_EDGE ( 'NONE', *, *, #47841, .F. ) ; +#19931 = ORIENTED_EDGE ( 'NONE', *, *, #90796, .T. ) ; +#19932 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#19933 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#19934 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#19935 = CIRCLE ( 'NONE', #8390, 0.01000000000000002623 ) ; +#19936 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8100000000000000533 ) ) ; +#19937 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19938 = FILL_AREA_STYLE_COLOUR ( '', #91774 ) ; +#19939 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45985 ) ) ; +#19940 = STYLED_ITEM ( 'NONE', ( #63478 ), #36471 ) ; +#19941 = FACE_OUTER_BOUND ( 'NONE', #52439, .T. ) ; +#19943 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#19942 = LINE ( 'NONE', #89880, #83935 ) ; +#19944 = DIRECTION ( 'NONE', ( -0.7071075504167435577, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#19945 = VERTEX_POINT ( 'NONE', #59715 ) ; +#19946 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#19947 = EDGE_LOOP ( 'NONE', ( #17293, #14511, #64378, #98827 ) ) ; +#19948 = VECTOR ( 'NONE', #52816, 1000.000000000000000 ) ; +#19949 = PRESENTATION_STYLE_ASSIGNMENT (( #58791 ) ) ; +#19950 = LINE ( 'NONE', #17911, #35087 ) ; +#19951 = CARTESIAN_POINT ( 'NONE', ( -0.2587106361308370017, -1.457888621141530061, 0.8100000000000000533 ) ) ; +#19952 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8648700000000000276 ) ) ; +#19953 = SURFACE_SIDE_STYLE ('',( #49109 ) ) ; +#19954 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19955 = CARTESIAN_POINT ( 'NONE', ( 1.780058980618379971, -1.124571705400470023, 0.8100000000000010525 ) ) ; +#19956 = ADVANCED_FACE ( 'NONE', ( #90809 ), #52021, .F. ) ; +#19957 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000140062184, 0.000000000000000000 ) ) ; +#19958 = MANIFOLD_SOLID_BREP ( 'ÊäÈë151', #2804 ) ; +#19959 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#19960 = ORIENTED_EDGE ( 'NONE', *, *, #94874, .T. ) ; +#19961 = VECTOR ( 'NONE', #92539, 1000.000000000000000 ) ; +#19963 = LINE ( 'NONE', #14259, #98968 ) ; +#19962 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#19964 = FILL_AREA_STYLE ('',( #12739 ) ) ; +#19965 = STYLED_ITEM ( 'NONE', ( #28177 ), #52753 ) ; +#19966 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40075, 'distance_accuracy_value', 'NONE'); +#19967 = ORIENTED_EDGE ( 'NONE', *, *, #9518, .T. ) ; +#19968 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#19969 = LINE ( 'NONE', #28154, #95028 ) ; +#19970 = FILL_AREA_STYLE ('',( #42954 ) ) ; +#19971 = SURFACE_STYLE_USAGE ( .BOTH. , #67433 ) ; +#19972 = STYLED_ITEM ( 'NONE', ( #44820 ), #52173 ) ; +#19973 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#19974 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#19976 = ADVANCED_FACE ( 'NONE', ( #46309 ), #86665, .T. ) ; +#19975 = STYLED_ITEM ( 'NONE', ( #45864 ), #46912 ) ; +#19977 = EDGE_CURVE ( 'NONE', #84697, #21523, #79005, .T. ) ; +#19978 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#19979 = ORIENTED_EDGE ( 'NONE', *, *, #781, .T. ) ; +#19980 = PRESENTATION_STYLE_ASSIGNMENT (( #89926 ) ) ; +#19981 = ORIENTED_EDGE ( 'NONE', *, *, #53097, .F. ) ; +#19982 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.383333333333333526, 0.000000000000000000 ) ) ; +#19983 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #172, 'distance_accuracy_value', 'NONE'); +#19984 = FACE_OUTER_BOUND ( 'NONE', #40665, .T. ) ; +#19985 = CARTESIAN_POINT ( 'NONE', ( -0.2243794914328909873, -1.066507643917919967, 0.8299999999999999600 ) ) ; +#19986 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#19987 = FILL_AREA_STYLE_COLOUR ( '', #52555 ) ; +#19988 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94965 ), #31436 ) ; +#19989 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#19990 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#19991 = SURFACE_STYLE_FILL_AREA ( #35362 ) ; +#19992 = VERTEX_POINT ( 'NONE', #10451 ) ; +#19993 = EDGE_CURVE ( 'NONE', #58097, #53914, #80032, .T. ) ; +#19994 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#19995 = EDGE_CURVE ( 'NONE', #52560, #94722, #57069, .T. ) ; +#19996 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#19997 = EDGE_LOOP ( 'NONE', ( #99889, #24727, #77638, #37285 ) ) ; +#19998 = FILL_AREA_STYLE_COLOUR ( '', #1728 ) ; +#19999 = VECTOR ( 'NONE', #90920, 1000.000000000000000 ) ; +#20000 = FACE_OUTER_BOUND ( 'NONE', #4243, .T. ) ; +#20001 = ORIENTED_EDGE ( 'NONE', *, *, #19042, .T. ) ; +#20002 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43623 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38896, #61892, #92485 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20003 = VECTOR ( 'NONE', #93988, 1000.000000000000000 ) ; +#20004 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20601 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98150, #28291, #59471 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20005 = SURFACE_STYLE_USAGE ( .BOTH. , #58864 ) ; +#20006 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8567 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30260, #61960, #61462 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20007 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#20008 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20009 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20010 = DIRECTION ( 'NONE', ( -0.3387340427540269649, 0.000000000000000000, -0.9408821649279537347 ) ) ; +#20011 = EDGE_LOOP ( 'NONE', ( #12204, #68860, #84674, #84336 ) ) ; +#20012 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#20013 = VECTOR ( 'NONE', #98853, 1000.000000000000000 ) ; +#20014 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20015 = EDGE_LOOP ( 'NONE', ( #33445, #45365, #16756, #24950 ) ) ; +#20016 = EDGE_CURVE ( 'NONE', #17366, #79801, #59396, .T. ) ; +#20017 = CIRCLE ( 'NONE', #29839, 1.319494367338009955 ) ; +#20018 = VERTEX_POINT ( 'NONE', #81044 ) ; +#20019 = ORIENTED_EDGE ( 'NONE', *, *, #28980, .F. ) ; +#20020 = EDGE_CURVE ( 'NONE', #76842, #82578, #57565, .T. ) ; +#20021 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93261, #9473, #25901, #41715 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#20022 = FILL_AREA_STYLE ('',( #35388 ) ) ; +#20023 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#20024 = SURFACE_SIDE_STYLE ('',( #64492 ) ) ; +#20025 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8490 ) ) ; +#20026 = ORIENTED_EDGE ( 'NONE', *, *, #45421, .T. ) ; +#20027 = ORIENTED_EDGE ( 'NONE', *, *, #39897, .F. ) ; +#20028 = VERTEX_POINT ( 'NONE', #26910 ) ; +#20029 = EDGE_CURVE ( 'NONE', #22641, #23706, #82257, .T. ) ; +#20030 = EDGE_LOOP ( 'NONE', ( #98549, #17462, #67723, #51103 ) ) ; +#20032 = ORIENTED_EDGE ( 'NONE', *, *, #62840, .T. ) ; +#20031 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20033 = SURFACE_STYLE_FILL_AREA ( #34888 ) ; +#20034 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20035 = FACE_OUTER_BOUND ( 'NONE', #9273, .T. ) ; +#20036 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72235 ), #82020 ) ; +#20037 = VERTEX_POINT ( 'NONE', #65188 ) ; +#20038 = DIRECTION ( 'NONE', ( 0.3631942952377805178, 0.000000000000000000, -0.9317134237021231780 ) ) ; +#20039 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #263, #7338, #52907, #31408 ), + .UNSPECIFIED., .F., .F. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#20040 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20041 = VERTEX_POINT ( 'NONE', #42715 ) ; +#20042 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20043 = STYLED_ITEM ( 'NONE', ( #33297 ), #88011 ) ; +#20044 = CARTESIAN_POINT ( 'NONE', ( 0.5106752425455549638, -1.185737326210950071, 0.8299999999999999600 ) ) ; +#20045 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20231, #60582, #51910 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20046 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.7099999999999999645, 0.9464466094067265356 ) ) ; +#20047 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#20049 = FILL_AREA_STYLE ('',( #45016 ) ) ; +#20048 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20050 = EDGE_CURVE ( 'NONE', #77000, #62914, #42230, .T. ) ; +#20051 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.297402597402600000, 0.8299999999999999600 ) ) ; +#20052 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39086 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66531, #97635, #73210 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20053 = VERTEX_POINT ( 'NONE', #96305 ) ; +#20054 = SURFACE_STYLE_FILL_AREA ( #67027 ) ; +#20055 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#20056 = CARTESIAN_POINT ( 'NONE', ( 1.337010325208910277, -1.189797473215369994, 0.8300000000000022915 ) ) ; +#20057 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6930 ), #68937 ) ; +#20058 = SURFACE_STYLE_FILL_AREA ( #42056 ) ; +#20059 = ADVANCED_FACE ( 'NONE', ( #56562 ), #87670, .T. ) ; +#20060 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20061 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 11.02344800000000014, 0.8648700000000000276 ) ) ; +#20062 = ADVANCED_FACE ( 'NONE', ( #19209 ), #66201, .T. ) ; +#20063 = VERTEX_POINT ( 'NONE', #67188 ) ; +#20064 = FILL_AREA_STYLE ('',( #10311 ) ) ; +#20066 = AXIS2_PLACEMENT_3D ( 'NONE', #38337, #21005, #52168 ) ; +#20065 = SURFACE_STYLE_FILL_AREA ( #97645 ) ; +#20067 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15071 ), #28188 ) ; +#20068 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#20069 = ORIENTED_EDGE ( 'NONE', *, *, #67832, .F. ) ; +#20070 = DIRECTION ( 'NONE', ( 0.7071071146859688739, -0.7071064476869688420, -0.000000000000000000 ) ) ; +#20071 = SURFACE_STYLE_FILL_AREA ( #35443 ) ; +#20072 = EDGE_CURVE ( 'NONE', #6603, #18846, #37584, .T. ) ; +#20073 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20075 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5397 ) ) ; +#20074 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20076 = VECTOR ( 'NONE', #3774, 1000.000000000000114 ) ; +#20077 = STYLED_ITEM ( 'NONE', ( #48338 ), #11702 ) ; +#20078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#20080 = ORIENTED_EDGE ( 'NONE', *, *, #93834, .T. ) ; +#20081 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266014999999999890, 0.8648700000000000276 ) ) ; +#20082 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#20083 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20084 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20085 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20086 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.2999999999999989897, 5.981926231290386527E-79 ) ) ; +#20087 = SURFACE_STYLE_USAGE ( .BOTH. , #82902 ) ; +#20088 = EDGE_CURVE ( 'NONE', #82829, #99336, #37082, .T. ) ; +#20089 = EDGE_CURVE ( 'NONE', #63527, #79474, #68178, .T. ) ; +#20090 = SURFACE_STYLE_USAGE ( .BOTH. , #17569 ) ; +#20091 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20092 = ORIENTED_EDGE ( 'NONE', *, *, #54529, .F. ) ; +#20093 = PRESENTATION_STYLE_ASSIGNMENT (( #90048 ) ) ; +#20094 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73911 ), #23391 ) ; +#20095 = ORIENTED_EDGE ( 'NONE', *, *, #2741, .F. ) ; +#20096 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#20097 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#20098 = SURFACE_STYLE_USAGE ( .BOTH. , #52776 ) ; +#20099 = FILL_AREA_STYLE_COLOUR ( '', #75787 ) ; +#20100 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8099999999999416556 ) ) ; +#20101 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8199999999999999512 ) ) ; +#20102 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#20103 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20104 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20105 = VERTEX_POINT ( 'NONE', #43206 ) ; +#20106 = MANIFOLD_SOLID_BREP ( 'ÊäÈë139', #66546 ) ; +#20107 = EDGE_CURVE ( 'NONE', #81638, #46528, #67672, .T. ) ; +#20108 = PLANE ( 'NONE', #35187 ) ; +#20109 = EDGE_CURVE ( 'NONE', #17633, #59639, #99725, .T. ) ; +#20110 = FILL_AREA_STYLE_COLOUR ( '', #85120 ) ; +#20111 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62488 ) ) ; +#20112 = SURFACE_STYLE_FILL_AREA ( #12388 ) ; +#20113 = ORIENTED_EDGE ( 'NONE', *, *, #74092, .T. ) ; +#20114 = PLANE ( 'NONE', #46116 ) ; +#20115 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20116 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041100000000085, 0.8991599999999999593 ) ) ; +#20117 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#20118 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20119 = CARTESIAN_POINT ( 'NONE', ( -1.316306714908529907, -1.318596846191909977, 0.8299999999999999600 ) ) ; +#20120 = ORIENTED_EDGE ( 'NONE', *, *, #60473, .T. ) ; +#20121 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20122 = PLANE ( 'NONE', #67407 ) ; +#20123 = ADVANCED_FACE ( 'NONE', ( #75856 ), #60082, .T. ) ; +#20124 = SURFACE_STYLE_USAGE ( .BOTH. , #67099 ) ; +#20125 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20126 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38029 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85421, #53290, #86654 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20127 = VERTEX_POINT ( 'NONE', #54408 ) ; +#20128 = EDGE_CURVE ( 'NONE', #88713, #37871, #39074, .T. ) ; +#20129 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26733 ), #77195 ) ; +#20130 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47949 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52127, #15784, #92864 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20131 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86995 ), #88660 ) ; +#20132 = SURFACE_STYLE_FILL_AREA ( #5789 ) ; +#20133 = LINE ( 'NONE', #4810, #15138 ) ; +#20134 = CARTESIAN_POINT ( 'NONE', ( -1.072510719476754026, -1.245286356562288033, 0.8099999999998073186 ) ) ; +#20135 = SURFACE_STYLE_USAGE ( .BOTH. , #58999 ) ; +#20136 = EDGE_LOOP ( 'NONE', ( #53228, #31069, #47121, #41907 ) ) ; +#20137 = AXIS2_PLACEMENT_3D ( 'NONE', #39784, #8535, #70930 ) ; +#20138 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57667 ), #54345 ) ; +#20139 = EDGE_CURVE ( 'NONE', #72195, #60396, #70193, .T. ) ; +#20140 = EDGE_CURVE ( 'NONE', #48454, #86964, #92646, .T. ) ; +#20141 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93885 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21101, #5731, #44556 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20142 = ORIENTED_EDGE ( 'NONE', *, *, #26082, .F. ) ; +#20144 = EDGE_LOOP ( 'NONE', ( #8218, #9406, #11765, #50580 ) ) ; +#20143 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20145 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5576, 'distance_accuracy_value', 'NONE'); +#20146 = VECTOR ( 'NONE', #11426, 1000.000000000000000 ) ; +#20147 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20149 = CARTESIAN_POINT ( 'NONE', ( -1.195496432507400009, -1.512608977738969962, 0.8100000000000000533 ) ) ; +#20148 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.2999999999999989897, 5.981926231290386527E-79 ) ) ; +#20150 = SURFACE_STYLE_FILL_AREA ( #97719 ) ; +#20151 = PRESENTATION_STYLE_ASSIGNMENT (( #98198 ) ) ; +#20152 = FACE_OUTER_BOUND ( 'NONE', #81100, .T. ) ; +#20153 = EDGE_LOOP ( 'NONE', ( #71368, #52680, #100033, #28226 ) ) ; +#20154 = SURFACE_SIDE_STYLE ('',( #59020 ) ) ; +#20155 = LINE ( 'NONE', #44629, #61086 ) ; +#20156 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20157 = ORIENTED_EDGE ( 'NONE', *, *, #73369, .T. ) ; +#20158 = CYLINDRICAL_SURFACE ( 'NONE', #97497, 0.1000000000000000472 ) ; +#20159 = ORIENTED_EDGE ( 'NONE', *, *, #74519, .F. ) ; +#20161 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#20160 = CARTESIAN_POINT ( 'NONE', ( 0.1505076962487483516, -1.469769718465016251, 0.8100000000000002753 ) ) ; +#20162 = SURFACE_SIDE_STYLE ('',( #44154 ) ) ; +#20163 = EDGE_CURVE ( 'NONE', #28843, #96910, #14531, .T. ) ; +#20164 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20165 = VECTOR ( 'NONE', #32261, 1000.000000000000000 ) ; +#20166 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20167 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20168 = ORIENTED_EDGE ( 'NONE', *, *, #22158, .F. ) ; +#20169 = CARTESIAN_POINT ( 'NONE', ( -0.2757359312880713897, 0.8200000000000000622, 0.1378679656440356671 ) ) ; +#20170 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66251 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28681, #35871, #36358 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20171 = EDGE_LOOP ( 'NONE', ( #92242, #25653, #95109, #76204 ) ) ; +#20172 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32738, #96486, #10651, #48049 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#20173 = FACE_OUTER_BOUND ( 'NONE', #54806, .T. ) ; +#20174 = ADVANCED_FACE ( 'NONE', ( #30368 ), #30894, .T. ) ; +#20175 = LINE ( 'NONE', #12449, #13881 ) ; +#20176 = VECTOR ( 'NONE', #33412, 1000.000000000000000 ) ; +#20177 = SURFACE_SIDE_STYLE ('',( #65658 ) ) ; +#20179 = EDGE_CURVE ( 'NONE', #15546, #85062, #15027, .T. ) ; +#20178 = SURFACE_STYLE_USAGE ( .BOTH. , #6308 ) ; +#20181 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #259 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77233, #93533, #22118 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20180 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20182 = VECTOR ( 'NONE', #80198, 1000.000000000000114 ) ; +#20183 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20184 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#20185 = CARTESIAN_POINT ( 'NONE', ( 1.199474818244760321, -0.9546485130184679813, 0.8100000000000000533 ) ) ; +#20186 = VERTEX_POINT ( 'NONE', #62077 ) ; +#20187 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#20188 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26789 ) ) ; +#20189 = EDGE_CURVE ( 'NONE', #90340, #86336, #761, .T. ) ; +#20191 = FACE_OUTER_BOUND ( 'NONE', #59164, .T. ) ; +#20190 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#20192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25165, 'distance_accuracy_value', 'NONE'); +#20193 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8648700000000000276 ) ) ; +#20194 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#20195 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95176 ) ) ; +#20196 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402591606, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#20197 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 8.675382000000000815, 0.8648700000000000276 ) ) ; +#20198 = SURFACE_STYLE_USAGE ( .BOTH. , #36561 ) ; +#20199 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20200 = EDGE_LOOP ( 'NONE', ( #25806, #97604, #79336, #64252 ) ) ; +#20201 = PLANE ( 'NONE', #99329 ) ; +#20202 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#20203 = SURFACE_STYLE_FILL_AREA ( #66181 ) ; +#20206 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49540 ), #3889 ) ; +#20205 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64245 ), #69136 ) ; +#20204 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20207 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20208 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#20209 = SURFACE_STYLE_USAGE ( .BOTH. , #99247 ) ; +#20210 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20212 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#20211 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17247 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84975, #52364, #22707 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20213 = SURFACE_STYLE_FILL_AREA ( #3413 ) ; +#20215 = EDGE_CURVE ( 'NONE', #90793, #95, #93646, .T. ) ; +#20214 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#20216 = EDGE_CURVE ( 'NONE', #65486, #270, #92168, .T. ) ; +#20217 = DIRECTION ( 'NONE', ( 0.7071067816865476141, 0.7071067806865475314, 0.000000000000000000 ) ) ; +#20218 = FACE_OUTER_BOUND ( 'NONE', #45372, .T. ) ; +#20219 = CYLINDRICAL_SURFACE ( 'NONE', #58615, 0.05000000000000012768 ) ; +#20220 = SURFACE_SIDE_STYLE ('',( #19734 ) ) ; +#20221 = SURFACE_STYLE_FILL_AREA ( #90167 ) ; +#20222 = VECTOR ( 'NONE', #100547, 1000.000000000000000 ) ; +#20223 = CARTESIAN_POINT ( 'NONE', ( 5.236461124874955964, 9.417844124874957146, 0.8648700000000000276 ) ) ; +#20224 = LINE ( 'NONE', #66205, #7857 ) ; +#20225 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36794 ), #98647 ) ; +#20226 = FILL_AREA_STYLE ('',( #28898 ) ) ; +#20227 = VERTEX_POINT ( 'NONE', #69154 ) ; +#20228 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20229 = PLANE ( 'NONE', #76353 ) ; +#20230 = EDGE_CURVE ( 'NONE', #54388, #51932, #63080, .T. ) ; +#20231 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20232 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95206 ), #59426 ) ; +#20234 = SURFACE_SIDE_STYLE ('',( #67204 ) ) ; +#20233 = SURFACE_SIDE_STYLE ('',( #11995 ) ) ; +#20235 = CARTESIAN_POINT ( 'NONE', ( -0.1097768158302629971, -0.9623926821384259922, 0.8300000000000002931 ) ) ; +#20236 = EDGE_CURVE ( 'NONE', #30045, #75293, #8335, .T. ) ; +#20237 = STYLED_ITEM ( 'NONE', ( #24338 ), #72136 ) ; +#20238 = ORIENTED_EDGE ( 'NONE', *, *, #97559, .F. ) ; +#20239 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20240 = VECTOR ( 'NONE', #46279, 1000.000000000000000 ) ; +#20241 = ORIENTED_EDGE ( 'NONE', *, *, #66063, .F. ) ; +#20242 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20243 = FILL_AREA_STYLE_COLOUR ( '', #91229 ) ; +#20244 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20245 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 0.1000000000000000056, -11.41999999999999993 ) ) ; +#20246 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20247 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49658 ) ) ; +#20248 = EDGE_LOOP ( 'NONE', ( #45287, #11683, #98067, #45661 ) ) ; +#20249 = EDGE_LOOP ( 'NONE', ( #71547, #9626, #27697, #54978, #60979, #41299, #15627 ) ) ; +#20250 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20251 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3324 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96, #39929, #79239 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20252 = PRESENTATION_STYLE_ASSIGNMENT (( #68211 ) ) ; +#20253 = ORIENTED_EDGE ( 'NONE', *, *, #60959, .T. ) ; +#20254 = CARTESIAN_POINT ( 'NONE', ( 1.823014099396639942, -1.319025261726090026, 0.8299999999999999600 ) ) ; +#20255 = AXIS2_PLACEMENT_3D ( 'NONE', #5628, #13769, #43973 ) ; +#20256 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23491 ), #75723 ) ; +#20257 = SURFACE_SIDE_STYLE ('',( #28444 ) ) ; +#20259 = VERTEX_POINT ( 'NONE', #16059 ) ; +#20258 = EDGE_LOOP ( 'NONE', ( #66486, #54702, #64151, #52493 ) ) ; +#20260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51347 ), #98469 ) ; +#20261 = ADVANCED_FACE ( 'NONE', ( #70707 ), #31917, .T. ) ; +#20262 = EDGE_LOOP ( 'NONE', ( #33618, #18377, #76045, #6123 ) ) ; +#20263 = ORIENTED_EDGE ( 'NONE', *, *, #44354, .T. ) ; +#20264 = SURFACE_SIDE_STYLE ('',( #4931 ) ) ; +#20265 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -8.400000000000000355, -11.36999999999999922 ) ) ; +#20266 = AXIS2_PLACEMENT_3D ( 'NONE', #59183, #28991, #51514 ) ; +#20267 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62689, 'distance_accuracy_value', 'NONE'); +#20269 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8100000000000000533 ) ) ; +#20268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20270 = EDGE_CURVE ( 'NONE', #34599, #10921, #96188, .T. ) ; +#20271 = VECTOR ( 'NONE', #29755, 1000.000000000000000 ) ; +#20272 = MANIFOLD_SOLID_BREP ( 'ÊäÈë123', #97507 ) ; +#20273 = SURFACE_STYLE_USAGE ( .BOTH. , #28458 ) ; +#20274 = LINE ( 'NONE', #34633, #47296 ) ; +#20276 = CIRCLE ( 'NONE', #77335, 1.293024339031550118 ) ; +#20275 = CIRCLE ( 'NONE', #10414, 0.2000000000000005107 ) ; +#20277 = CARTESIAN_POINT ( 'NONE', ( -1.305325210527780166, -0.9264544496121620565, 0.8100000000000000533 ) ) ; +#20278 = ORIENTED_EDGE ( 'NONE', *, *, #32241, .T. ) ; +#20279 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#20280 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6993 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89533, #65517, #73694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20281 = ORIENTED_EDGE ( 'NONE', *, *, #19190, .F. ) ; +#20282 = ORIENTED_EDGE ( 'NONE', *, *, #17663, .F. ) ; +#20283 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14769 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74658, #5153, #89955 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20284 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#20285 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8648700000000000276 ) ) ; +#20286 = ADVANCED_FACE ( 'NONE', ( #3296 ), #26293, .T. ) ; +#20287 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20289 = ORIENTED_EDGE ( 'NONE', *, *, #27337, .F. ) ; +#20288 = SURFACE_STYLE_FILL_AREA ( #82604 ) ; +#20290 = AXIS2_PLACEMENT_3D ( 'NONE', #85695, #47402, #94346 ) ; +#20291 = PRESENTATION_STYLE_ASSIGNMENT (( #75928 ) ) ; +#20292 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666646623, -0.1000000000000000056, 0.000000000000000000 ) ) ; +#20293 = VECTOR ( 'NONE', #80745, 1000.000000000000000 ) ; +#20294 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20295 = FACE_OUTER_BOUND ( 'NONE', #39583, .T. ) ; +#20296 = VERTEX_POINT ( 'NONE', #3790 ) ; +#20297 = CYLINDRICAL_SURFACE ( 'NONE', #35159, 0.009999999999999998473 ) ; +#20298 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8199999999999999512, 0.2000000000000000111 ) ) ; +#20299 = ORIENTED_EDGE ( 'NONE', *, *, #1502, .T. ) ; +#20300 = ORIENTED_EDGE ( 'NONE', *, *, #27198, .F. ) ; +#20301 = FILL_AREA_STYLE ('',( #12580 ) ) ; +#20302 = EDGE_CURVE ( 'NONE', #33648, #12510, #56945, .T. ) ; +#20303 = SURFACE_STYLE_FILL_AREA ( #43293 ) ; +#20304 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.3000000000000000444, 1.048695503451051965E-76 ) ) ; +#20305 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20306 = SURFACE_STYLE_USAGE ( .BOTH. , #36168 ) ; +#20307 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20308 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8782 ) ) ; +#20309 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#20310 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#20311 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100000, 'distance_accuracy_value', 'NONE'); +#20312 = VERTEX_POINT ( 'NONE', #5241 ) ; +#20313 = PLANE ( 'NONE', #88773 ) ; +#20314 = ORIENTED_EDGE ( 'NONE', *, *, #5242, .F. ) ; +#20315 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20316 = EDGE_CURVE ( 'NONE', #41421, #100629, #21115, .T. ) ; +#20317 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20318 = CARTESIAN_POINT ( 'NONE', ( 1.337010325208910277, -1.189797473215369994, 0.8299999999999999600 ) ) ; +#20320 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#20319 = STYLED_ITEM ( 'NONE', ( #81677 ), #89416 ) ; +#20321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90438 ), #787 ) ; +#20322 = SURFACE_STYLE_FILL_AREA ( #90273 ) ; +#20323 = SURFACE_STYLE_USAGE ( .BOTH. , #92623 ) ; +#20324 = FACE_OUTER_BOUND ( 'NONE', #80044, .T. ) ; +#20325 = EDGE_CURVE ( 'NONE', #3505, #46536, #52281, .T. ) ; +#20326 = PRESENTATION_STYLE_ASSIGNMENT (( #75461 ) ) ; +#20327 = ORIENTED_EDGE ( 'NONE', *, *, #41747, .T. ) ; +#20328 = LINE ( 'NONE', #20840, #21539 ) ; +#20329 = PLANE ( 'NONE', #21139 ) ; +#20330 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60709 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31706, #16863, #62884 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20331 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82935 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10965, #36063, #89671 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20332 = FILL_AREA_STYLE ('',( #51527 ) ) ; +#20333 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#20334 = FACE_OUTER_BOUND ( 'NONE', #89525, .T. ) ; +#20335 = VECTOR ( 'NONE', #25937, 1000.000000000000000 ) ; +#20336 = CARTESIAN_POINT ( 'NONE', ( 1.899701586460730285, -1.304291937284929981, 0.8100000000000000533 ) ) ; +#20337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45788, 'distance_accuracy_value', 'NONE'); +#20338 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55562, #78009, #23905, #66086 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#20339 = ADVANCED_FACE ( 'NONE', ( #13372 ), #28763, .F. ) ; +#20341 = EDGE_CURVE ( 'NONE', #78778, #29189, #29281, .T. ) ; +#20340 = FILL_AREA_STYLE ('',( #87401 ) ) ; +#20342 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30162 ) ) ; +#20343 = SURFACE_STYLE_FILL_AREA ( #72974 ) ; +#20344 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, -0.01500000000000004108, 0.2399999999999999356 ) ) ; +#20345 = EDGE_CURVE ( 'NONE', #91206, #38810, #67068, .T. ) ; +#20346 = EDGE_CURVE ( 'NONE', #55576, #59380, #51773, .T. ) ; +#20347 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#20348 = VECTOR ( 'NONE', #861, 1000.000000000000000 ) ; +#20349 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77405 ) ) ; +#20351 = ORIENTED_EDGE ( 'NONE', *, *, #71038, .T. ) ; +#20350 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20352 = LINE ( 'NONE', #51543, #58385 ) ; +#20353 = LINE ( 'NONE', #75984, #82927 ) ; +#20354 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20355 = EDGE_LOOP ( 'NONE', ( #84243, #36371, #31209, #50601 ) ) ; +#20356 = LINE ( 'NONE', #52029, #10259 ) ; +#20357 = SURFACE_SIDE_STYLE ('',( #37702 ) ) ; +#20358 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20359 = EDGE_CURVE ( 'NONE', #1465, #77051, #20598, .T. ) ; +#20360 = AXIS2_PLACEMENT_3D ( 'NONE', #87537, #64561, #56932 ) ; +#20361 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.899999999999999911, 0.1829999999999919746 ) ) ; +#20362 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#20363 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000311, -0.02000000000000839995 ) ) ; +#20364 = EDGE_CURVE ( 'NONE', #64838, #6703, #12367, .T. ) ; +#20365 = ORIENTED_EDGE ( 'NONE', *, *, #65910, .F. ) ; +#20366 = ORIENTED_EDGE ( 'NONE', *, *, #57381, .T. ) ; +#20367 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20368 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36714 ) ) ; +#20369 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#20370 = FILL_AREA_STYLE_COLOUR ( '', #86261 ) ; +#20371 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95339 ) ) ; +#20372 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20373 = FILL_AREA_STYLE_COLOUR ( '', #5962 ) ; +#20374 = SURFACE_STYLE_USAGE ( .BOTH. , #77373 ) ; +#20375 = SURFACE_STYLE_USAGE ( .BOTH. , #4058 ) ; +#20376 = ORIENTED_EDGE ( 'NONE', *, *, #49240, .F. ) ; +#20377 = EDGE_LOOP ( 'NONE', ( #62247, #61471, #11528, #86953 ) ) ; +#20378 = VECTOR ( 'NONE', #10375, 1000.000000000000000 ) ; +#20379 = ORIENTED_EDGE ( 'NONE', *, *, #26439, .F. ) ; +#20380 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20381 = VECTOR ( 'NONE', #27619, 999.9999999999998863 ) ; +#20382 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.000000000000000000 ) ) ; +#20383 = FACE_OUTER_BOUND ( 'NONE', #65857, .T. ) ; +#20384 = SURFACE_SIDE_STYLE ('',( #52556 ) ) ; +#20385 = CARTESIAN_POINT ( 'NONE', ( -1.231483759408549927, -0.9661431204389000493, 0.8299999999999999600 ) ) ; +#20386 = VECTOR ( 'NONE', #47858, 1000.000000000000000 ) ; +#20389 = VERTEX_POINT ( 'NONE', #97189 ) ; +#20388 = ORIENTED_EDGE ( 'NONE', *, *, #7003, .T. ) ; +#20387 = AXIS2_PLACEMENT_3D ( 'NONE', #4578, #19414, #27104 ) ; +#20390 = ORIENTED_EDGE ( 'NONE', *, *, #1413, .F. ) ; +#20391 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8991599999999999593 ) ) ; +#20392 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90081 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45316, #84648, #48776 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20393 = STYLED_ITEM ( 'NONE', ( #35182 ), #54040 ) ; +#20394 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67221, 'distance_accuracy_value', 'NONE'); +#20395 = SURFACE_STYLE_FILL_AREA ( #64864 ) ; +#20396 = ORIENTED_EDGE ( 'NONE', *, *, #55793, .T. ) ; +#20397 = ADVANCED_FACE ( 'NONE', ( #67550 ), #68053, .T. ) ; +#20399 = EDGE_LOOP ( 'NONE', ( #57124, #65480, #30071, #95984 ) ) ; +#20398 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20400 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#20401 = SURFACE_STYLE_USAGE ( .BOTH. , #27595 ) ; +#20402 = VECTOR ( 'NONE', #5057, 1000.000000000000000 ) ; +#20403 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, -0.2250000000000000333 ) ) ; +#20404 = PRESENTATION_STYLE_ASSIGNMENT (( #97950 ) ) ; +#20405 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#20406 = ORIENTED_EDGE ( 'NONE', *, *, #8939, .T. ) ; +#20407 = ORIENTED_EDGE ( 'NONE', *, *, #88206, .F. ) ; +#20408 = VECTOR ( 'NONE', #46648, 1000.000000000000000 ) ; +#20409 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20410 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.000000000000000000, -0.7071067811865475727 ) ) ; +#20411 = VERTEX_POINT ( 'NONE', #22621 ) ; +#20412 = AXIS2_PLACEMENT_3D ( 'NONE', #58877, #6146, #36365 ) ; +#20413 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#20414 = ORIENTED_EDGE ( 'NONE', *, *, #91262, .T. ) ; +#20415 = FILL_AREA_STYLE_COLOUR ( '', #55478 ) ; +#20416 = EDGE_LOOP ( 'NONE', ( #24485, #40371, #58292, #10483, #88798, #84180 ) ) ; +#20418 = CARTESIAN_POINT ( 'NONE', ( -0.02839774098039829844, -1.241062917987890257, 0.8100000000000000533 ) ) ; +#20417 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43798 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6964, #55571, #38203 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20419 = FILL_AREA_STYLE_COLOUR ( '', #15028 ) ; +#20420 = EDGE_LOOP ( 'NONE', ( #52402, #3223, #51820, #46246 ) ) ; +#20421 = ORIENTED_EDGE ( 'NONE', *, *, #27015, .F. ) ; +#20422 = PRESENTATION_STYLE_ASSIGNMENT (( #19426 ) ) ; +#20423 = EDGE_CURVE ( 'NONE', #72427, #83944, #7706, .T. ) ; +#20424 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.7000000000000001776, 0.000000000000000000 ) ) ; +#20425 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66068 ), #51443 ) ; +#20426 = SURFACE_STYLE_USAGE ( .BOTH. , #59289 ) ; +#20427 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42350 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32293, #71602, #94011 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20428 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.123820061220075051, 0.000000000000000000 ) ) ; +#20429 = FILL_AREA_STYLE ('',( #19938 ) ) ; +#20430 = AXIS2_PLACEMENT_3D ( 'NONE', #13314, #75685, #91507 ) ; +#20431 = STYLED_ITEM ( 'NONE', ( #1234 ), #98042 ) ; +#20432 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#20434 = SURFACE_SIDE_STYLE ('',( #72067 ) ) ; +#20433 = CYLINDRICAL_SURFACE ( 'NONE', #2393, 0.05000000000000012768 ) ; +#20435 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#20436 = ORIENTED_EDGE ( 'NONE', *, *, #31359, .F. ) ; +#20437 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20438 = CARTESIAN_POINT ( 'NONE', ( -1.139646564935959949, -1.515470133326519919, 0.8100000000000000533 ) ) ; +#20439 = ORIENTED_EDGE ( 'NONE', *, *, #40297, .T. ) ; +#20440 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20441 = FILL_AREA_STYLE_COLOUR ( '', #75788 ) ; +#20443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55955 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #156, #86959, #85426 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20442 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999961697, -0.02000000000000000042 ) ) ; +#20444 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#20445 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20446 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#20447 = PRESENTATION_STYLE_ASSIGNMENT (( #97992 ) ) ; +#20448 = MANIFOLD_SOLID_BREP ( 'ÊäÈë81', #30668 ) ; +#20449 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20450 = FILL_AREA_STYLE ('',( #89900 ) ) ; +#20451 = PRESENTATION_STYLE_ASSIGNMENT (( #89901 ) ) ; +#20452 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#20453 = EDGE_LOOP ( 'NONE', ( #6387, #9598, #5240, #69482 ) ) ; +#20454 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20455 = SURFACE_STYLE_FILL_AREA ( #51648 ) ; +#20456 = PLANE ( 'NONE', #19524 ) ; +#20457 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20458 = ADVANCED_FACE ( 'NONE', ( #54276 ), #76736, .T. ) ; +#20459 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#20460 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84032 ) ) ; +#20461 = STYLED_ITEM ( 'NONE', ( #17427 ), #54433 ) ; +#20462 = ORIENTED_EDGE ( 'NONE', *, *, #7869, .F. ) ; +#20463 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54280 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63121, #25828, #55472 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20465 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#20466 = CYLINDRICAL_SURFACE ( 'NONE', #29813, 0.04999999999999991257 ) ; +#20467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56390 ), #77379 ) ; +#20468 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20469 = SURFACE_STYLE_FILL_AREA ( #90421 ) ; +#20470 = SURFACE_STYLE_USAGE ( .BOTH. , #98499 ) ; +#20472 = FACE_OUTER_BOUND ( 'NONE', #86546, .T. ) ; +#20471 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25403 ) ) ; +#20473 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#20474 = VECTOR ( 'NONE', #784, 1000.000000000000000 ) ; +#20475 = VECTOR ( 'NONE', #7090, 1000.000000000000114 ) ; +#20476 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#20477 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #39447, #47622 ), + ( #24679, #78758 ), + ( #61958, #55319 ), + ( #70594, #94564 ), + ( #86429, #7714 ), + ( #86942, #100598 ), + ( #31794, #62972 ), + ( #23643, #55804 ), + ( #25183, #32813 ), + ( #38958, #32310 ), + ( #85914, #70075 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.1253844121579349991, 0.2490499212940600060, 0.3727373688245280148, 0.4983139852987960028, 0.6236767560303250191, 0.7468439467830330081, 0.8707651621907409600, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#20478 = EDGE_CURVE ( 'NONE', #41045, #100007, #126, .T. ) ; +#20479 = PRESENTATION_STYLE_ASSIGNMENT (( #28162 ) ) ; +#20480 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20481 = EDGE_LOOP ( 'NONE', ( #85122, #43384, #23516, #4441 ) ) ; +#20482 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20483 = ORIENTED_EDGE ( 'NONE', *, *, #52456, .T. ) ; +#20484 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13091, 'distance_accuracy_value', 'NONE'); +#20485 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86668, 'distance_accuracy_value', 'NONE'); +#20486 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20487 = LINE ( 'NONE', #35848, #25197 ) ; +#20488 = DIRECTION ( 'NONE', ( 0.3376989467541747225, 0.9412541746845646262, 0.000000000000000000 ) ) ; +#20489 = SURFACE_STYLE_FILL_AREA ( #97067 ) ; +#20490 = CARTESIAN_POINT ( 'NONE', ( 0.4770107896369426559, -1.223330622371237020, 0.8100000000000001643 ) ) ; +#20491 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#20492 = SURFACE_STYLE_FILL_AREA ( #36835 ) ; +#20493 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, 3.500000000000000444, 0.000000000000000000 ) ) ; +#20494 = PLANE ( 'NONE', #59202 ) ; +#20495 = ORIENTED_EDGE ( 'NONE', *, *, #10775, .F. ) ; +#20496 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33500 ) ) ; +#20497 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#20498 = PRESENTATION_STYLE_ASSIGNMENT (( #43480 ) ) ; +#20500 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22172 ) ) ; +#20499 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#20501 = ORIENTED_EDGE ( 'NONE', *, *, #30840, .F. ) ; +#20502 = VECTOR ( 'NONE', #23511, 1000.000000000000000 ) ; +#20503 = EDGE_LOOP ( 'NONE', ( #58198, #93705, #16338, #47051 ) ) ; +#20504 = VECTOR ( 'NONE', #95504, 1000.000000000000000 ) ; +#20505 = PLANE ( 'NONE', #4516 ) ; +#20506 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20507 = VECTOR ( 'NONE', #26586, 1000.000000000000000 ) ; +#20508 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 1.458578643762689975, -0.02000000000000000042 ) ) ; +#20509 = SURFACE_SIDE_STYLE ('',( #58866 ) ) ; +#20510 = FACE_OUTER_BOUND ( 'NONE', #76201, .T. ) ; +#20511 = ORIENTED_EDGE ( 'NONE', *, *, #28410, .T. ) ; +#20512 = VECTOR ( 'NONE', #53464, 1000.000000000000000 ) ; +#20513 = FILL_AREA_STYLE_COLOUR ( '', #9808 ) ; +#20514 = EDGE_LOOP ( 'NONE', ( #31996, #30230, #84052, #36273 ) ) ; +#20515 = VERTEX_POINT ( 'NONE', #62451 ) ; +#20516 = EDGE_CURVE ( 'NONE', #16995, #41801, #54805, .T. ) ; +#20517 = EDGE_LOOP ( 'NONE', ( #66006, #11892, #73819, #303 ) ) ; +#20518 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20519 = FILL_AREA_STYLE_COLOUR ( '', #82128 ) ; +#20520 = PRESENTATION_STYLE_ASSIGNMENT (( #76158 ) ) ; +#20521 = ORIENTED_EDGE ( 'NONE', *, *, #56987, .F. ) ; +#20523 = ORIENTED_EDGE ( 'NONE', *, *, #22240, .F. ) ; +#20522 = STYLED_ITEM ( 'NONE', ( #29722 ), #73590 ) ; +#20524 = ORIENTED_EDGE ( 'NONE', *, *, #37033, .F. ) ; +#20525 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2808578643762690286, 0.1399999999999980149 ) ) ; +#20526 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61028, #23725, #84480, #69109 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#20527 = VECTOR ( 'NONE', #86623, 1000.000000000000000 ) ; +#20528 = VERTEX_POINT ( 'NONE', #69035 ) ; +#20529 = AXIS2_PLACEMENT_3D ( 'NONE', #29841, #30321, #77818 ) ; +#20530 = STYLED_ITEM ( 'NONE', ( #19365 ), #90278 ) ; +#20531 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 3.266015000000000335, 0.8648700000000000276 ) ) ; +#20533 = SURFACE_SIDE_STYLE ('',( #14341 ) ) ; +#20532 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100296 ), #56454 ) ; +#20534 = CARTESIAN_POINT ( 'NONE', ( 3.519999999999989804, -7.594371560187019297E-15, 0.000000000000000000 ) ) ; +#20535 = ORIENTED_EDGE ( 'NONE', *, *, #45588, .F. ) ; +#20536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20537 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.1000000000000000056, -13.25000000000000000 ) ) ; +#20538 = ORIENTED_EDGE ( 'NONE', *, *, #78901, .F. ) ; +#20539 = VECTOR ( 'NONE', #9599, 1000.000000000000000 ) ; +#20540 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84691 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72081, #2140, #4134 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20541 = EDGE_CURVE ( 'NONE', #45252, #80372, #43986, .T. ) ; +#20542 = CARTESIAN_POINT ( 'NONE', ( 0.2457017931905739472, -1.400963434758352388, 0.8100000000000001643 ) ) ; +#20543 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20544 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20545 = FILL_AREA_STYLE_COLOUR ( '', #46692 ) ; +#20547 = FILL_AREA_STYLE_COLOUR ( '', #27463 ) ; +#20546 = STYLED_ITEM ( 'NONE', ( #100292 ), #78719 ) ; +#20548 = EDGE_CURVE ( 'NONE', #14770, #10872, #100105, .T. ) ; +#20549 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20550 = CARTESIAN_POINT ( 'NONE', ( 1.807266337641940002, -1.389839611604140046, 0.8100000000000000533 ) ) ; +#20551 = SURFACE_STYLE_FILL_AREA ( #83361 ) ; +#20552 = FILL_AREA_STYLE ('',( #90504 ) ) ; +#20553 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41123 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79576, #4453, #35140 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20554 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.2999999999999999889, -0.02000000000001470393 ) ) ; +#20555 = STYLED_ITEM ( 'NONE', ( #13219 ), #61801 ) ; +#20556 = ORIENTED_EDGE ( 'NONE', *, *, #73512, .F. ) ; +#20557 = FILL_AREA_STYLE_COLOUR ( '', #41852 ) ; +#20558 = FILL_AREA_STYLE_COLOUR ( '', #13987 ) ; +#20559 = VECTOR ( 'NONE', #82668, 1000.000000000000000 ) ; +#20560 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20562 = LINE ( 'NONE', #80877, #68663 ) ; +#20561 = CARTESIAN_POINT ( 'NONE', ( 0.4178376006486049787, -0.9790859034276460093, 0.8299999999999999600 ) ) ; +#20563 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000000666, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#20564 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, -3.500000000000000444, 0.000000000000000000 ) ) ; +#20565 = EDGE_CURVE ( 'NONE', #66668, #70008, #32801, .T. ) ; +#20566 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20567 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20568 = ORIENTED_EDGE ( 'NONE', *, *, #47636, .T. ) ; +#20569 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61285 ), #7447 ) ; +#20570 = FILL_AREA_STYLE_COLOUR ( '', #95971 ) ; +#20571 = FILL_AREA_STYLE ('',( #59433 ) ) ; +#20572 = ORIENTED_EDGE ( 'NONE', *, *, #45260, .T. ) ; +#20573 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#20575 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20574 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 5.557041000000000786, 0.8648700000000000276 ) ) ; +#20576 = CARTESIAN_POINT ( 'NONE', ( 1.667677657188980200, -0.9647878283071119609, 0.8100000000000000533 ) ) ; +#20577 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20578 = ADVANCED_FACE ( 'NONE', ( #72600 ), #17948, .F. ) ; +#20579 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20580 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20581 = CARTESIAN_POINT ( 'NONE', ( 2.818155750249974112, 6.999539249750025505, 0.8991599999999999593 ) ) ; +#20582 = ORIENTED_EDGE ( 'NONE', *, *, #9646, .F. ) ; +#20583 = FACE_OUTER_BOUND ( 'NONE', #7617, .T. ) ; +#20584 = SURFACE_STYLE_USAGE ( .BOTH. , #68542 ) ; +#20585 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20586 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20587 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#20588 = CARTESIAN_POINT ( 'NONE', ( 1.049748415576440053, -1.475020827802409951, 0.8300000000000010703 ) ) ; +#20589 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#20590 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20591 = SURFACE_STYLE_FILL_AREA ( #28279 ) ; +#20592 = FILL_AREA_STYLE_COLOUR ( '', #27341 ) ; +#20593 = LINE ( 'NONE', #5746, #8371 ) ; +#20594 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60547, 'distance_accuracy_value', 'NONE'); +#20595 = EDGE_CURVE ( 'NONE', #100078, #84214, #4174, .T. ) ; +#20596 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20597 = ORIENTED_EDGE ( 'NONE', *, *, #90787, .F. ) ; +#20598 = LINE ( 'NONE', #12873, #38368 ) ; +#20599 = VERTEX_POINT ( 'NONE', #72113 ) ; +#20600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68203, 'distance_accuracy_value', 'NONE'); +#20601 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98150, 'distance_accuracy_value', 'NONE'); +#20602 = CARTESIAN_POINT ( 'NONE', ( 1.148869891942319921, -0.9585643914498560569, 0.8100000000000000533 ) ) ; +#20603 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69490 ), #87454 ) ; +#20604 = STYLED_ITEM ( 'NONE', ( #78845 ), #90495 ) ; +#20605 = LINE ( 'NONE', #67075, #11192 ) ; +#20606 = CARTESIAN_POINT ( 'NONE', ( 1.825861765333669950, -0.9394184040112200096, 0.8299999999999999600 ) ) ; +#20607 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#20608 = SURFACE_STYLE_FILL_AREA ( #12882 ) ; +#20609 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333330195, 1.699999999999999956, 1.747825839084982648E-76 ) ) ; +#20610 = ORIENTED_EDGE ( 'NONE', *, *, #19746, .T. ) ; +#20611 = MANIFOLD_SOLID_BREP ( 'ÊäÈë179', #87697 ) ; +#20612 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8199999999999999512 ) ) ; +#20613 = FILL_AREA_STYLE_COLOUR ( '', #48693 ) ; +#20614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74186, 'distance_accuracy_value', 'NONE'); +#20615 = VECTOR ( 'NONE', #40025, 1000.000000000000000 ) ; +#20616 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, -0.01085786437626906110, 0.2500000000000000000 ) ) ; +#20617 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20618 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100448 ) ) ; +#20619 = STYLED_ITEM ( 'NONE', ( #80074 ), #49121 ) ; +#20620 = ORIENTED_EDGE ( 'NONE', *, *, #97313, .F. ) ; +#20621 = SURFACE_STYLE_FILL_AREA ( #6246 ) ; +#20622 = SURFACE_STYLE_FILL_AREA ( #59490 ) ; +#20623 = CARTESIAN_POINT ( 'NONE', ( 1.436760428889430008, -1.381526214478759895, 0.8299999999999994049 ) ) ; +#20624 = EDGE_CURVE ( 'NONE', #92104, #56618, #73118, .T. ) ; +#20625 = SURFACE_SIDE_STYLE ('',( #98167 ) ) ; +#20626 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.399999999999999911, -11.57000000000000028 ) ) ; +#20627 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20628 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24461 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62183, #46809, #39163 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20629 = ORIENTED_EDGE ( 'NONE', *, *, #44516, .T. ) ; +#20630 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20631 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#20632 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27770, 'distance_accuracy_value', 'NONE'); +#20633 = CIRCLE ( 'NONE', #67907, 0.2137111836784290342 ) ; +#20634 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#20635 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20636 = EDGE_CURVE ( 'NONE', #52513, #56700, #26670, .T. ) ; +#20637 = VERTEX_POINT ( 'NONE', #48641 ) ; +#20638 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41805 ) ) ; +#20639 = AXIS2_PLACEMENT_3D ( 'NONE', #8851, #266, #63088 ) ; +#20640 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8100000000001210676 ) ) ; +#20641 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#20642 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20643 = CARTESIAN_POINT ( 'NONE', ( -0.9983308346332699923, -1.292011617012603253, 0.8099999999997731237 ) ) ; +#20644 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20645 = VERTEX_POINT ( 'NONE', #57831 ) ; +#20646 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15737 ) ) ; +#20647 = VECTOR ( 'NONE', #22555, 1000.000000000000000 ) ; +#20648 = STYLED_ITEM ( 'NONE', ( #5196 ), #4550 ) ; +#20649 = EDGE_LOOP ( 'NONE', ( #48350, #95593, #53577, #52760 ) ) ; +#20651 = ORIENTED_EDGE ( 'NONE', *, *, #73978, .F. ) ; +#20650 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, 0.000000000000000000 ) ) ; +#20652 = STYLED_ITEM ( 'NONE', ( #33997 ), #13121 ) ; +#20654 = CARTESIAN_POINT ( 'NONE', ( -1.219099199802559985, -1.508462442331270026, 0.8299999999999999600 ) ) ; +#20653 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#20655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20656 = FILL_AREA_STYLE ('',( #36017 ) ) ; +#20657 = FILL_AREA_STYLE_COLOUR ( '', #72781 ) ; +#20658 = PRESENTATION_STYLE_ASSIGNMENT (( #28823 ) ) ; +#20659 = ORIENTED_EDGE ( 'NONE', *, *, #24964, .F. ) ; +#20660 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999997780, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#20661 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20662 = FILL_AREA_STYLE ('',( #90627 ) ) ; +#20663 = AXIS2_PLACEMENT_3D ( 'NONE', #55585, #55068, #16699 ) ; +#20664 = EDGE_LOOP ( 'NONE', ( #11532, #93171, #80690, #1825, #31820, #96498 ) ) ; +#20665 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35436 ), #4412 ) ; +#20667 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20666 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#20668 = ORIENTED_EDGE ( 'NONE', *, *, #3921, .F. ) ; +#20669 = EDGE_CURVE ( 'NONE', #51969, #47678, #79266, .T. ) ; +#20671 = SURFACE_SIDE_STYLE ('',( #90636 ) ) ; +#20670 = PRESENTATION_STYLE_ASSIGNMENT (( #90635 ) ) ; +#20672 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87591 ), #59866 ) ; +#20673 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#20674 = FACE_OUTER_BOUND ( 'NONE', #89372, .T. ) ; +#20675 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64712 ), #14079 ) ; +#20676 = VECTOR ( 'NONE', #82152, 1000.000000000000000 ) ; +#20677 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662329837, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#20678 = EDGE_LOOP ( 'NONE', ( #94977, #7242, #22062, #79136 ) ) ; +#20679 = SURFACE_STYLE_FILL_AREA ( #37027 ) ; +#20680 = VERTEX_POINT ( 'NONE', #79784 ) ; +#20681 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#20683 = SURFACE_STYLE_USAGE ( .BOTH. , #97747 ) ; +#20682 = SURFACE_SIDE_STYLE ('',( #57521 ) ) ; +#20684 = PRESENTATION_STYLE_ASSIGNMENT (( #4852 ) ) ; +#20685 = ADVANCED_FACE ( 'NONE', ( #32300 ), #9731, .T. ) ; +#20686 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64716 ) ) ; +#20687 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, 3.149999999999990585, 0.000000000000000000 ) ) ; +#20688 = ADVANCED_FACE ( 'NONE', ( #58333 ), #42482, .F. ) ; +#20689 = CYLINDRICAL_SURFACE ( 'NONE', #5174, 0.009999999999999998473 ) ; +#20690 = AXIS2_PLACEMENT_3D ( 'NONE', #60901, #32764, #16898 ) ; +#20692 = ADVANCED_FACE ( 'NONE', ( #59344 ), #75132, .T. ) ; +#20691 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20693 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20694 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100963 ) ; +#20695 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#20696 = FILL_AREA_STYLE ('',( #12964 ) ) ; +#20697 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#20698 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61717 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36120, #12019, #35624 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20699 = ORIENTED_EDGE ( 'NONE', *, *, #95014, .F. ) ; +#20700 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#20701 = STYLED_ITEM ( 'NONE', ( #39935 ), #62267 ) ; +#20704 = SURFACE_STYLE_FILL_AREA ( #66167 ) ; +#20703 = FILL_AREA_STYLE ('',( #66166 ) ) ; +#20702 = FILL_AREA_STYLE_COLOUR ( '', #85425 ) ; +#20705 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20706 = LINE ( 'NONE', #82511, #31583 ) ; +#20707 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85780 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23757, #37579, #47226 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20708 = ADVANCED_FACE ( 'NONE', ( #92895 ), #45431, .T. ) ; +#20709 = STYLED_ITEM ( 'NONE', ( #88326 ), #23160 ) ; +#20710 = PLANE ( 'NONE', #57650 ) ; +#20711 = ORIENTED_EDGE ( 'NONE', *, *, #59706, .T. ) ; +#20712 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27238 ), #100463 ) ; +#20714 = ADVANCED_FACE ( 'NONE', ( #7081 ), #78137, .T. ) ; +#20713 = LINE ( 'NONE', #54390, #88590 ) ; +#20715 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20716 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20717 = SURFACE_STYLE_USAGE ( .BOTH. , #42216 ) ; +#20718 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20719 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#20720 = FILL_AREA_STYLE ('',( #43192 ) ) ; +#20721 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.000000000000000000 ) ) ; +#20722 = FILL_AREA_STYLE ('',( #5858 ) ) ; +#20723 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9276 ), #98909 ) ; +#20724 = CARTESIAN_POINT ( 'NONE', ( 13.17837700000000112, 9.889034999999999798, 0.8648700000000000276 ) ) ; +#20725 = SURFACE_STYLE_USAGE ( .BOTH. , #16169 ) ; +#20726 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, 0.000000000000000000 ) ) ; +#20727 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#20728 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999540328 ) ) ; +#20729 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20730 = FILL_AREA_STYLE ('',( #30366 ) ) ; +#20731 = EDGE_CURVE ( 'NONE', #30702, #10244, #83789, .T. ) ; +#20732 = SURFACE_STYLE_USAGE ( .BOTH. , #59590 ) ; +#20734 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74311 ) ) ; +#20735 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#20736 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100741, 'distance_accuracy_value', 'NONE'); +#20737 = ADVANCED_FACE ( 'NONE', ( #15289 ), #91931, .T. ) ; +#20738 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#20739 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8199999999999999512 ) ) ; +#20740 = ORIENTED_EDGE ( 'NONE', *, *, #92981, .F. ) ; +#20741 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20742 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20743 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58825, 'distance_accuracy_value', 'NONE'); +#20744 = LINE ( 'NONE', #45197, #41064 ) ; +#20745 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25102, 'distance_accuracy_value', 'NONE'); +#20746 = LINE ( 'NONE', #21243, #34002 ) ; +#20747 = CIRCLE ( 'NONE', #66443, 0.01000000000000002623 ) ; +#20748 = LINE ( 'NONE', #75875, #99590 ) ; +#20749 = PRESENTATION_STYLE_ASSIGNMENT (( #90703 ) ) ; +#20750 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14266 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33022, #66173, #26389 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20751 = EDGE_CURVE ( 'NONE', #83440, #60233, #43226, .T. ) ; +#20752 = ORIENTED_EDGE ( 'NONE', *, *, #68844, .T. ) ; +#20753 = FACE_OUTER_BOUND ( 'NONE', #5075, .T. ) ; +#20754 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#20755 = ORIENTED_EDGE ( 'NONE', *, *, #100, .T. ) ; +#20756 = FACE_OUTER_BOUND ( 'NONE', #78934, .T. ) ; +#20757 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#20758 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33054, 'distance_accuracy_value', 'NONE'); +#20759 = VECTOR ( 'NONE', #46963, 1000.000000000000000 ) ; +#20760 = STYLED_ITEM ( 'NONE', ( #2908 ), #90919 ) ; +#20761 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20762 = SURFACE_SIDE_STYLE ('',( #65735 ) ) ; +#20763 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20764 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20765 = VERTEX_POINT ( 'NONE', #78623 ) ; +#20766 = ORIENTED_EDGE ( 'NONE', *, *, #68373, .F. ) ; +#20767 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20768 = ORIENTED_EDGE ( 'NONE', *, *, #16426, .T. ) ; +#20769 = EDGE_CURVE ( 'NONE', #21531, #21309, #9113, .T. ) ; +#20770 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20771 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, 0.000000000000000000 ) ) ; +#20772 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#20774 = ORIENTED_EDGE ( 'NONE', *, *, #37617, .T. ) ; +#20773 = ORIENTED_EDGE ( 'NONE', *, *, #32118, .T. ) ; +#20775 = VECTOR ( 'NONE', #77338, 1000.000000000000000 ) ; +#20776 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20777 = ADVANCED_FACE ( 'NONE', ( #25048 ), #35601, .F. ) ; +#20778 = ORIENTED_EDGE ( 'NONE', *, *, #25269, .T. ) ; +#20779 = ORIENTED_EDGE ( 'NONE', *, *, #19993, .F. ) ; +#20780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20781 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94578, #8735, #7726 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20782 = SURFACE_STYLE_FILL_AREA ( #59645 ) ; +#20783 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55069 ), #82747 ) ; +#20784 = CARTESIAN_POINT ( 'NONE', ( 0.3671721421540899977, -0.9001501144350020356, 0.8299999999999999600 ) ) ; +#20785 = CLOSED_SHELL ( 'NONE', ( #31003, #48613, #408, #61155, #73237, #26011 ) ) ; +#20786 = MANIFOLD_SOLID_BREP ( 'ÊäÈë73', #40417 ) ; +#20787 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20788 = CARTESIAN_POINT ( 'NONE', ( -0.1500692249665822597, -1.164568096342160297, 0.8100000000000000533 ) ) ; +#20789 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82756 ), #15810 ) ; +#20790 = CARTESIAN_POINT ( 'NONE', ( -1.216120372379269954, -0.8900438058027670962, 0.8100000000000000533 ) ) ; +#20791 = ORIENTED_EDGE ( 'NONE', *, *, #51905, .F. ) ; +#20792 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#20793 = ORIENTED_EDGE ( 'NONE', *, *, #80173, .T. ) ; +#20794 = VERTEX_POINT ( 'NONE', #97322 ) ; +#20795 = EDGE_CURVE ( 'NONE', #57747, #76382, #48001, .T. ) ; +#20796 = CARTESIAN_POINT ( 'NONE', ( 0.9977603010112831017, -1.128484622308769891, 0.8100000000000000533 ) ) ; +#20797 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1263 ), #48595 ) ; +#20799 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8299999999999999600 ) ) ; +#20798 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#20800 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#20801 = CYLINDRICAL_SURFACE ( 'NONE', #1666, 0.5799999999999999600 ) ; +#20803 = ORIENTED_EDGE ( 'NONE', *, *, #61025, .T. ) ; +#20802 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#20804 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64833 ) ) ; +#20805 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.5033332678708700714, 0.6832601346887902105 ) ) ; +#20806 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2761799387799140360, -0.02000000000000000042 ) ) ; +#20807 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.500000000000000444, 0.000000000000000000 ) ) ; +#20808 = ORIENTED_EDGE ( 'NONE', *, *, #54626, .T. ) ; +#20810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#20809 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#20811 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#20812 = ORIENTED_EDGE ( 'NONE', *, *, #99317, .F. ) ; +#20813 = VERTEX_POINT ( 'NONE', #27417 ) ; +#20815 = SURFACE_STYLE_USAGE ( .BOTH. , #27493 ) ; +#20814 = SURFACE_STYLE_FILL_AREA ( #3991 ) ; +#20816 = LINE ( 'NONE', #29480, #27781 ) ; +#20817 = LINE ( 'NONE', #83117, #97002 ) ; +#20818 = EDGE_CURVE ( 'NONE', #61165, #14055, #20748, .T. ) ; +#20819 = SURFACE_STYLE_USAGE ( .BOTH. , #90771 ) ; +#20820 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#20821 = VECTOR ( 'NONE', #99601, 1000.000000000000000 ) ; +#20822 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20823 = LINE ( 'NONE', #83120, #91717 ) ; +#20824 = PLANE ( 'NONE', #40478 ) ; +#20825 = VECTOR ( 'NONE', #50398, 1000.000000000000000 ) ; +#20826 = VERTEX_POINT ( 'NONE', #5877 ) ; +#20827 = FILL_AREA_STYLE ('',( #89765 ) ) ; +#20828 = ORIENTED_EDGE ( 'NONE', *, *, #65200, .T. ) ; +#20829 = SURFACE_STYLE_FILL_AREA ( #43304 ) ; +#20830 = LINE ( 'NONE', #100810, #79154 ) ; +#20831 = CARTESIAN_POINT ( 'NONE', ( 1.416650401028419992, -1.249140550102370018, 0.8299999999999999600 ) ) ; +#20832 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20833 = VECTOR ( 'NONE', #82051, 1000.000000000000000 ) ; +#20834 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6112 ), #99005 ) ; +#20835 = SURFACE_STYLE_USAGE ( .BOTH. , #89285 ) ; +#20836 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20837 = SURFACE_STYLE_USAGE ( .BOTH. , #91762 ) ; +#20839 = ORIENTED_EDGE ( 'NONE', *, *, #56299, .F. ) ; +#20838 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84564 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76483, #45810, #78010 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20840 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#20841 = FILL_AREA_STYLE ('',( #28026 ) ) ; +#20842 = SURFACE_SIDE_STYLE ('',( #25629 ) ) ; +#20843 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20844 = SURFACE_STYLE_USAGE ( .BOTH. , #67292 ) ; +#20845 = SURFACE_STYLE_USAGE ( .BOTH. , #91287 ) ; +#20846 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20847 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20848 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95818 ), #64878 ) ; +#20849 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20850 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25165, #17936, #26154 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20851 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28561 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84644, #10449, #80031 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20852 = EDGE_CURVE ( 'NONE', #50722, #46905, #68695, .T. ) ; +#20853 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20854 = CARTESIAN_POINT ( 'NONE', ( 4.691989249749913604, 7.954133249749911982, 0.8648700000000000276 ) ) ; +#20855 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30663 ) ) ; +#20856 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35343, 'distance_accuracy_value', 'NONE'); +#20857 = ORIENTED_EDGE ( 'NONE', *, *, #68017, .T. ) ; +#20858 = CLOSED_SHELL ( 'NONE', ( #59683, #14981, #57327, #3863, #64072, #66936 ) ) ; +#20859 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#20860 = DIRECTION ( 'NONE', ( -1.649990468822289917E-78, 1.000000000000000000, -3.396003576002217664E-125 ) ) ; +#20861 = VERTEX_POINT ( 'NONE', #14550 ) ; +#20862 = CARTESIAN_POINT ( 'NONE', ( -0.7522321428571430157, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#20863 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#20864 = FACE_OUTER_BOUND ( 'NONE', #35092, .T. ) ; +#20865 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18399, 'distance_accuracy_value', 'NONE'); +#20866 = LINE ( 'NONE', #52034, #96456 ) ; +#20867 = LINE ( 'NONE', #20362, #36762 ) ; +#20868 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.000000000000000000 ) ) ; +#20869 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89441 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77477, #6949, #30483 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20870 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15433 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64893, #9177, #31732 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20871 = EDGE_CURVE ( 'NONE', #210, #26467, #62192, .T. ) ; +#20872 = VERTEX_POINT ( 'NONE', #74881 ) ; +#20873 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #88620, #72236 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #41649 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#20874 = FILL_AREA_STYLE_COLOUR ( '', #30298 ) ; +#20875 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.000000000000000000 ) ) ; +#20876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100621 ) ) ; +#20877 = SURFACE_STYLE_USAGE ( .BOTH. , #28539 ) ; +#20878 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65694, 'distance_accuracy_value', 'NONE'); +#20879 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20880 = SURFACE_STYLE_USAGE ( .BOTH. , #83184 ) ; +#20881 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #133, 'distance_accuracy_value', 'NONE'); +#20882 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20883 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25796 ) ) ; +#20884 = EDGE_CURVE ( 'NONE', #66631, #9027, #58679, .T. ) ; +#20885 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#20886 = ORIENTED_EDGE ( 'NONE', *, *, #90526, .F. ) ; +#20887 = ORIENTED_EDGE ( 'NONE', *, *, #36348, .T. ) ; +#20888 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44331, 'distance_accuracy_value', 'NONE'); +#20889 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20890 = CIRCLE ( 'NONE', #34195, 0.2500000000000000000 ) ; +#20891 = EDGE_LOOP ( 'NONE', ( #99580, #89845, #70561, #73342 ) ) ; +#20892 = AXIS2_PLACEMENT_3D ( 'NONE', #81729, #93331, #91855 ) ; +#20893 = SURFACE_STYLE_FILL_AREA ( #29551 ) ; +#20894 = SURFACE_SIDE_STYLE ('',( #35248 ) ) ; +#20895 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998900047, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#20896 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35653 ) ) ; +#20897 = CARTESIAN_POINT ( 'NONE', ( -0.3663668861142549971, -1.072315624320830274, 0.8299999999999999600 ) ) ; +#20898 = CARTESIAN_POINT ( 'NONE', ( -1.291038328540720093, -1.030374455384980070, 0.8299999999999999600 ) ) ; +#20899 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20901 = VERTEX_POINT ( 'NONE', #83044 ) ; +#20900 = ORIENTED_EDGE ( 'NONE', *, *, #51608, .F. ) ; +#20902 = EDGE_CURVE ( 'NONE', #100163, #3674, #97797, .T. ) ; +#20903 = AXIS2_PLACEMENT_3D ( 'NONE', #78664, #25097, #78181 ) ; +#20904 = ORIENTED_EDGE ( 'NONE', *, *, #52182, .T. ) ; +#20905 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20906 = VECTOR ( 'NONE', #93159, 1000.000000000000000 ) ; +#20907 = STYLED_ITEM ( 'NONE', ( #98617 ), #91358 ) ; +#20908 = FACE_OUTER_BOUND ( 'NONE', #11437, .T. ) ; +#20909 = ORIENTED_EDGE ( 'NONE', *, *, #51992, .F. ) ; +#20910 = EDGE_CURVE ( 'NONE', #58180, #9357, #72037, .T. ) ; +#20911 = AXIS2_PLACEMENT_3D ( 'NONE', #73873, #80543, #19745 ) ; +#20912 = VERTEX_POINT ( 'NONE', #60100 ) ; +#20913 = SURFACE_STYLE_USAGE ( .BOTH. , #75056 ) ; +#20914 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20915 = SURFACE_STYLE_USAGE ( .BOTH. , #98931 ) ; +#20916 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48708 ) ) ; +#20918 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#20917 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000019873, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#20919 = LINE ( 'NONE', #98933, #63799 ) ; +#20920 = VERTEX_POINT ( 'NONE', #13515 ) ; +#20921 = ORIENTED_EDGE ( 'NONE', *, *, #8836, .F. ) ; +#20922 = FILL_AREA_STYLE_COLOUR ( '', #35646 ) ; +#20923 = ORIENTED_EDGE ( 'NONE', *, *, #11751, .T. ) ; +#20924 = EDGE_CURVE ( 'NONE', #56416, #35265, #28417, .T. ) ; +#20925 = EDGE_CURVE ( 'NONE', #11007, #71668, #13008, .T. ) ; +#20926 = FACE_OUTER_BOUND ( 'NONE', #55090, .T. ) ; +#20927 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95897 ) ) ; +#20928 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45587 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70799, #56533, #87140 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20931 = EDGE_CURVE ( 'NONE', #6853, #81133, #84048, .T. ) ; +#20930 = ORIENTED_EDGE ( 'NONE', *, *, #22563, .F. ) ; +#20929 = CARTESIAN_POINT ( 'NONE', ( 0.9002637987012981347, 0.6899999999999999467, 1.084202172485504434E-16 ) ) ; +#20932 = EDGE_CURVE ( 'NONE', #19927, #68921, #9722, .T. ) ; +#20933 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61765 ) ) ; +#20934 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#20935 = PLANE ( 'NONE', #68469 ) ; +#20936 = VERTEX_POINT ( 'NONE', #6841 ) ; +#20937 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#20938 = CLOSED_SHELL ( 'NONE', ( #29894, #96817, #65104, #20458, #2474, #77214 ) ) ; +#20939 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20940 = ORIENTED_EDGE ( 'NONE', *, *, #41131, .T. ) ; +#20941 = EDGE_LOOP ( 'NONE', ( #10142, #53558, #66549, #93702 ) ) ; +#20942 = ADVANCED_FACE ( 'NONE', ( #99740 ), #29904, .T. ) ; +#20943 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20944 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#20945 = ADVANCED_FACE ( 'NONE', ( #100242 ), #87072, .T. ) ; +#20947 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#20946 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#20948 = SURFACE_STYLE_USAGE ( .BOTH. , #36286 ) ; +#20949 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8991599999999999593 ) ) ; +#20950 = SURFACE_SIDE_STYLE ('',( #90898 ) ) ; +#20951 = ORIENTED_EDGE ( 'NONE', *, *, #88316, .F. ) ; +#20952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20953 = ORIENTED_EDGE ( 'NONE', *, *, #18841, .F. ) ; +#20954 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#20955 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36826 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45435, #36824, #6105 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#20956 = CARTESIAN_POINT ( 'NONE', ( -0.1759195832032370010, -1.500900992704750081, 0.8299999999999999600 ) ) ; +#20957 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20958 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#20959 = PRESENTATION_STYLE_ASSIGNMENT (( #90912 ) ) ; +#20960 = CARTESIAN_POINT ( 'NONE', ( 1.757815472291410330, -1.145059460293619935, 0.8100000000000000533 ) ) ; +#20961 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#20962 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#20963 = MANIFOLD_SOLID_BREP ( 'ÊäÈë161', #51785 ) ; +#20964 = CARTESIAN_POINT ( 'NONE', ( 0.001420454545454350121, 0.6899999999999999467, 0.4397321428571430713 ) ) ; +#20965 = VECTOR ( 'NONE', #39698, 999.9999999999998863 ) ; +#20966 = FILL_AREA_STYLE_COLOUR ( '', #19810 ) ; +#20967 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97595 ), #43843 ) ; +#20968 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20969 = VECTOR ( 'NONE', #74986, 1000.000000000000000 ) ; +#20971 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#20970 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 3.958979999999999944, 0.8648700000000000276 ) ) ; +#20972 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#20973 = FACE_OUTER_BOUND ( 'NONE', #11281, .T. ) ; +#20974 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97550 ) ) ; +#20975 = VECTOR ( 'NONE', #7578, 1000.000000000000000 ) ; +#20977 = ADVANCED_FACE ( 'NONE', ( #47755 ), #92664, .T. ) ; +#20976 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37959, 'distance_accuracy_value', 'NONE'); +#20978 = ORIENTED_EDGE ( 'NONE', *, *, #22757, .T. ) ; +#20979 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20980 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29151 ) ) ; +#20981 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20982 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76437 ), #24301 ) ; +#20983 = PLANE ( 'NONE', #35013 ) ; +#20984 = LINE ( 'NONE', #75603, #33121 ) ; +#20985 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#20986 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#20987 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#20988 = STYLED_ITEM ( 'NONE', ( #20959 ), #79949 ) ; +#20989 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#20990 = FILL_AREA_STYLE_COLOUR ( '', #44004 ) ; +#20991 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.299999999999999822, 0.1829999999999499805 ) ) ; +#20992 = VECTOR ( 'NONE', #42799, 1000.000000000000000 ) ; +#20993 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#20994 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58577 ), #87832 ) ; +#20995 = ORIENTED_EDGE ( 'NONE', *, *, #1349, .T. ) ; +#20996 = SURFACE_STYLE_FILL_AREA ( #5129 ) ; +#20997 = ORIENTED_EDGE ( 'NONE', *, *, #18057, .T. ) ; +#20998 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65029 ) ) ; +#20999 = SURFACE_STYLE_USAGE ( .BOTH. , #36328 ) ; +#21000 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29474, 'distance_accuracy_value', 'NONE'); +#21001 = PRESENTATION_STYLE_ASSIGNMENT (( #12248 ) ) ; +#21002 = SURFACE_SIDE_STYLE ('',( #29170 ) ) ; +#21004 = AXIS2_PLACEMENT_3D ( 'NONE', #41617, #57457, #17091 ) ; +#21003 = LINE ( 'NONE', #13252, #51484 ) ; +#21005 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21006 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21007 = CARTESIAN_POINT ( 'NONE', ( -1.383450513385342084, 1.393384075926970000, 0.8100000000000001643 ) ) ; +#21008 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4699999999999999734, 0.000000000000000000 ) ) ; +#21009 = SURFACE_STYLE_FILL_AREA ( #51166 ) ; +#21010 = AXIS2_PLACEMENT_3D ( 'NONE', #60895, #15885, #78214 ) ; +#21011 = ORIENTED_EDGE ( 'NONE', *, *, #73160, .F. ) ; +#21012 = EDGE_CURVE ( 'NONE', #63380, #90793, #95692, .T. ) ; +#21013 = ORIENTED_EDGE ( 'NONE', *, *, #17014, .T. ) ; +#21014 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8648700000000000276 ) ) ; +#21015 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.383333333333326642, 1.747825839084889375E-76 ) ) ; +#21016 = ORIENTED_EDGE ( 'NONE', *, *, #43608, .F. ) ; +#21017 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35845 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16649, #80893, #70810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21018 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#21019 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65045 ) ) ; +#21020 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8648700000000000276 ) ) ; +#21021 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#21022 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67553 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39031, #213, #46143 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21023 = SURFACE_STYLE_USAGE ( .BOTH. , #44968 ) ; +#21024 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21026 = EDGE_LOOP ( 'NONE', ( #35708, #47278, #16407, #19010 ) ) ; +#21025 = ORIENTED_EDGE ( 'NONE', *, *, #17777, .F. ) ; +#21028 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95940 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80172, #57714, #56701 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21027 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21029 = ORIENTED_EDGE ( 'NONE', *, *, #5330, .F. ) ; +#21030 = SURFACE_STYLE_USAGE ( .BOTH. , #99035 ) ; +#21032 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261924000000000046, 0.8648700000000000276 ) ) ; +#21031 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21033 = EDGE_LOOP ( 'NONE', ( #77642, #80211, #95969, #50168 ) ) ; +#21034 = VERTEX_POINT ( 'NONE', #88080 ) ; +#21035 = FILL_AREA_STYLE ('',( #12795 ) ) ; +#21036 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21037 = PLANE ( 'NONE', #64184 ) ; +#21038 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53687 ), #84650 ) ; +#21039 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99216 ), #53688 ) ; +#21041 = SURFACE_STYLE_USAGE ( .BOTH. , #82827 ) ; +#21040 = FACE_OUTER_BOUND ( 'NONE', #15247, .T. ) ; +#21042 = EDGE_LOOP ( 'NONE', ( #88752, #33141, #66114, #68396 ) ) ; +#21043 = ORIENTED_EDGE ( 'NONE', *, *, #33260, .F. ) ; +#21044 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95013, #40443, #79226, #25145 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21045 = EDGE_LOOP ( 'NONE', ( #80160, #24960, #66730, #61870 ) ) ; +#21046 = PRESENTATION_STYLE_ASSIGNMENT (( #100521 ) ) ; +#21047 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37314 ), #52038 ) ; +#21048 = VECTOR ( 'NONE', #25908, 1000.000000000000000 ) ; +#21049 = VECTOR ( 'NONE', #31330, 1000.000000000000000 ) ; +#21051 = ORIENTED_EDGE ( 'NONE', *, *, #60941, .T. ) ; +#21050 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#21052 = EDGE_CURVE ( 'NONE', #81075, #29437, #19110, .T. ) ; +#21053 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24946 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50184, #81324, #42496 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21054 = STYLED_ITEM ( 'NONE', ( #21732 ), #91904 ) ; +#21055 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92170, #6824, #59592, #100223 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21056 = SURFACE_SIDE_STYLE ('',( #89619 ) ) ; +#21057 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#21058 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8648700000000000276 ) ) ; +#21059 = ORIENTED_EDGE ( 'NONE', *, *, #26958, .T. ) ; +#21060 = CARTESIAN_POINT ( 'NONE', ( -0.008659704439726766123, -1.028973459703212745, 0.8100000000002030021 ) ) ; +#21061 = FILL_AREA_STYLE ('',( #53704 ) ) ; +#21062 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21063 = VERTEX_POINT ( 'NONE', #42125 ) ; +#21064 = VECTOR ( 'NONE', #82946, 1000.000000000000000 ) ; +#21065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21066 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21067 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21068 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.399999999999999911, -11.36999999999999922 ) ) ; +#21069 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21070 = SURFACE_SIDE_STYLE ('',( #75199 ) ) ; +#21071 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#21072 = EDGE_CURVE ( 'NONE', #61349, #26467, #88563, .T. ) ; +#21073 = SURFACE_SIDE_STYLE ('',( #58908 ) ) ; +#21075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21074 = FACE_OUTER_BOUND ( 'NONE', #51851, .T. ) ; +#21076 = CARTESIAN_POINT ( 'NONE', ( -1.101868639237005398, -1.164076084035879699, 0.8099999999998671596 ) ) ; +#21077 = STYLED_ITEM ( 'NONE', ( #86158 ), #63752 ) ; +#21078 = FILL_AREA_STYLE ('',( #43039 ) ) ; +#21079 = STYLED_ITEM ( 'NONE', ( #89293 ), #1533 ) ; +#21080 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#21081 = ORIENTED_EDGE ( 'NONE', *, *, #91121, .F. ) ; +#21082 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21083 = CARTESIAN_POINT ( 'NONE', ( 1.119708175802679895, -1.130592060098940088, 0.8300000000000022915 ) ) ; +#21084 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3147 ) ) ; +#21085 = CARTESIAN_POINT ( 'NONE', ( 1.568874050374579943, -1.341601374162270099, 0.8100000000000000533 ) ) ; +#21086 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#21087 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16097 ), #79850 ) ; +#21088 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01085786437626904723, 0.1499999999999999944 ) ) ; +#21089 = ORIENTED_EDGE ( 'NONE', *, *, #95099, .F. ) ; +#21090 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#21091 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79780 ), #4747 ) ; +#21092 = ORIENTED_EDGE ( 'NONE', *, *, #2613, .F. ) ; +#21093 = EDGE_CURVE ( 'NONE', #32276, #79538, #50804, .T. ) ; +#21094 = SURFACE_STYLE_FILL_AREA ( #51243 ) ; +#21095 = LINE ( 'NONE', #77720, #49386 ) ; +#21096 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21097 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21098 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#21099 = EDGE_CURVE ( 'NONE', #60734, #14330, #95189, .T. ) ; +#21100 = ORIENTED_EDGE ( 'NONE', *, *, #19066, .T. ) ; +#21101 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21102 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21103 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84721 ) ) ; +#21104 = STYLED_ITEM ( 'NONE', ( #61513 ), #75496 ) ; +#21105 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21106 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21107 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#21108 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 1.013711183678429162 ) ) ; +#21109 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#21110 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67716, #75395, #37117, #66239 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21111 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42341 ) ) ; +#21112 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21113 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21114 = VERTEX_POINT ( 'NONE', #97212 ) ; +#21115 = LINE ( 'NONE', #75731, #66059 ) ; +#21116 = ORIENTED_EDGE ( 'NONE', *, *, #12533, .T. ) ; +#21117 = CARTESIAN_POINT ( 'NONE', ( 1.111216736053209919, -0.9708075278790050389, 0.8100000000000000533 ) ) ; +#21118 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.1199999999999999956, 0.8499999999999999778 ) ) ; +#21119 = AXIS2_PLACEMENT_3D ( 'NONE', #88691, #26425, #31177 ) ; +#21121 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21120 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65711 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43583, #34468, #19100 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21122 = SURFACE_STYLE_USAGE ( .BOTH. , #22630 ) ; +#21123 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#21124 = CARTESIAN_POINT ( 'NONE', ( -0.08340097402597418386, 0.6899999999999999467, 0.2077922077922079724 ) ) ; +#21125 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99150 ) ) ; +#21126 = FACE_OUTER_BOUND ( 'NONE', #42776, .T. ) ; +#21127 = ORIENTED_EDGE ( 'NONE', *, *, #81477, .F. ) ; +#21128 = MANIFOLD_SOLID_BREP ( 'ÊäÈë22', #43730 ) ; +#21129 = FACE_OUTER_BOUND ( 'NONE', #95552, .T. ) ; +#21130 = EDGE_CURVE ( 'NONE', #55998, #43775, #81454, .T. ) ; +#21131 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57092 ) ) ; +#21132 = VERTEX_POINT ( 'NONE', #25807 ) ; +#21133 = PRESENTATION_STYLE_ASSIGNMENT (( #89088 ) ) ; +#21134 = EDGE_CURVE ( 'NONE', #72043, #55010, #72755, .T. ) ; +#21135 = SURFACE_STYLE_FILL_AREA ( #61473 ) ; +#21136 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#21137 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#21138 = LINE ( 'NONE', #52307, #54657 ) ; +#21139 = AXIS2_PLACEMENT_3D ( 'NONE', #28999, #84632, #7938 ) ; +#21140 = ORIENTED_EDGE ( 'NONE', *, *, #68125, .T. ) ; +#21141 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#21142 = FILL_AREA_STYLE_COLOUR ( '', #39114 ) ; +#21143 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21208 ) ) ; +#21144 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21145 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2000000000000000111, -13.40000000000000036 ) ) ; +#21146 = CARTESIAN_POINT ( 'NONE', ( 1.616346165234739729, -0.9925253384799740397, 0.8099999999999994982 ) ) ; +#21147 = ADVANCED_FACE ( 'NONE', ( #2813 ), #80945, .F. ) ; +#21148 = ORIENTED_EDGE ( 'NONE', *, *, #18999, .F. ) ; +#21149 = ADVANCED_FACE ( 'NONE', ( #13914 ), #67574, .T. ) ; +#21150 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21151 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999990452, -0.02000000000000000042 ) ) ; +#21152 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#21153 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21154 = CARTESIAN_POINT ( 'NONE', ( 1.536752279304230084, -1.444662699359980040, 0.8300000000000001821 ) ) ; +#21155 = VERTEX_POINT ( 'NONE', #4312 ) ; +#21156 = AXIS2_PLACEMENT_3D ( 'NONE', #77232, #79270, #31787 ) ; +#21157 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21158 = EDGE_LOOP ( 'NONE', ( #88136, #73298, #24509, #34299, #44371, #34767 ) ) ; +#21160 = ORIENTED_EDGE ( 'NONE', *, *, #98243, .F. ) ; +#21159 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#21161 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12587, 'distance_accuracy_value', 'NONE'); +#21162 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#21163 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21164 = SURFACE_SIDE_STYLE ('',( #59016 ) ) ; +#21165 = ORIENTED_EDGE ( 'NONE', *, *, #77962, .F. ) ; +#21166 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#21167 = VERTEX_POINT ( 'NONE', #12891 ) ; +#21168 = SURFACE_STYLE_FILL_AREA ( #84953 ) ; +#21169 = FILL_AREA_STYLE_COLOUR ( '', #33468 ) ; +#21170 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#21171 = AXIS2_PLACEMENT_3D ( 'NONE', #13777, #1926, #64215 ) ; +#21172 = EDGE_LOOP ( 'NONE', ( #88414, #89475, #64357, #58605 ) ) ; +#21174 = SURFACE_STYLE_USAGE ( .BOTH. , #7281 ) ; +#21173 = FILL_AREA_STYLE_COLOUR ( '', #16113 ) ; +#21175 = ORIENTED_EDGE ( 'NONE', *, *, #86904, .T. ) ; +#21176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86414 ), #100915 ) ; +#21177 = EDGE_CURVE ( 'NONE', #29437, #77186, #44584, .T. ) ; +#21178 = AXIS2_PLACEMENT_3D ( 'NONE', #11547, #3492, #42785 ) ; +#21180 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21179 = LINE ( 'NONE', #81503, #20146 ) ; +#21181 = SURFACE_STYLE_FILL_AREA ( #37529 ) ; +#21182 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#21183 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28312, #20121, #34992 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21184 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60366 ), #81580 ) ; +#21185 = ORIENTED_EDGE ( 'NONE', *, *, #35900, .T. ) ; +#21186 = ORIENTED_EDGE ( 'NONE', *, *, #67035, .T. ) ; +#21188 = CARTESIAN_POINT ( 'NONE', ( 0.9400000000000000577, 1.757708562033497989E-17, 0.3000000000000000444 ) ) ; +#21187 = PRESENTATION_STYLE_ASSIGNMENT (( #84478 ) ) ; +#21189 = PRESENTATION_STYLE_ASSIGNMENT (( #91142 ) ) ; +#21190 = CARTESIAN_POINT ( 'NONE', ( -0.9238200612200850870, 3.099999999999989875, 0.000000000000000000 ) ) ; +#21191 = VECTOR ( 'NONE', #97548, 1000.000000000000000 ) ; +#21192 = EDGE_CURVE ( 'NONE', #37766, #9040, #35983, .T. ) ; +#21193 = STYLED_ITEM ( 'NONE', ( #14767 ), #65190 ) ; +#21194 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21195 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#21196 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21197 = CYLINDRICAL_SURFACE ( 'NONE', #93402, 0.9754570600145798798 ) ; +#21198 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#21199 = ORIENTED_EDGE ( 'NONE', *, *, #15463, .T. ) ; +#21200 = ADVANCED_FACE ( 'NONE', ( #45084 ), #20114, .F. ) ; +#21201 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21202 = VECTOR ( 'NONE', #84622, 1000.000000000000000 ) ; +#21205 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21204 = PLANE ( 'NONE', #4924 ) ; +#21203 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -7.819266067965463093E-18, 0.3499999999999999223 ) ) ; +#21206 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24696, 'distance_accuracy_value', 'NONE'); +#21207 = LINE ( 'NONE', #84988, #97390 ) ; +#21208 = STYLED_ITEM ( 'NONE', ( #11836 ), #42761 ) ; +#21209 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999990319, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#21210 = CARTESIAN_POINT ( 'NONE', ( -1.250988841353219971, -1.419390247362990021, 0.8299999999999998490 ) ) ; +#21211 = PLANE ( 'NONE', #98997 ) ; +#21212 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#21213 = PRESENTATION_STYLE_ASSIGNMENT (( #74839 ) ) ; +#21214 = EDGE_CURVE ( 'NONE', #28576, #59367, #78287, .T. ) ; +#21215 = ORIENTED_EDGE ( 'NONE', *, *, #17663, .T. ) ; +#21216 = CARTESIAN_POINT ( 'NONE', ( -2.966666666666666785, -3.500000000000000000, 0.000000000000000000 ) ) ; +#21217 = LINE ( 'NONE', #62063, #82379 ) ; +#21218 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#21219 = VECTOR ( 'NONE', #64239, 1000.000000000000000 ) ; +#21220 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21221 = CIRCLE ( 'NONE', #53878, 0.009999999999999998473 ) ; +#21222 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21223 = PRESENTATION_STYLE_ASSIGNMENT (( #74853 ) ) ; +#21224 = FILL_AREA_STYLE_COLOUR ( '', #42947 ) ; +#21225 = PLANE ( 'NONE', #94029 ) ; +#21226 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21227 = SURFACE_STYLE_USAGE ( .BOTH. , #61064 ) ; +#21228 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21229 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21230 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21231 = LINE ( 'NONE', #12482, #32498 ) ; +#21232 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.000000000000000000 ) ) ; +#21233 = STYLED_ITEM ( 'NONE', ( #87940 ), #44921 ) ; +#21234 = FACE_OUTER_BOUND ( 'NONE', #36873, .T. ) ; +#21235 = PRESENTATION_STYLE_ASSIGNMENT (( #44204 ) ) ; +#21236 = CARTESIAN_POINT ( 'NONE', ( 1.726282678897220091, -1.159841243706410063, 0.8299999999999997380 ) ) ; +#21237 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#21238 = VERTEX_POINT ( 'NONE', #30782 ) ; +#21239 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21240 = FILL_AREA_STYLE_COLOUR ( '', #9387 ) ; +#21241 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#21242 = VECTOR ( 'NONE', #61596, 1000.000000000000000 ) ; +#21243 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#21244 = SURFACE_SIDE_STYLE ('',( #98775 ) ) ; +#21245 = EDGE_CURVE ( 'NONE', #62837, #56095, #35523, .T. ) ; +#21246 = EDGE_CURVE ( 'NONE', #72729, #6062, #93544, .T. ) ; +#21247 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79951 ), #25 ) ; +#21248 = AXIS2_PLACEMENT_3D ( 'NONE', #34022, #73320, #95232 ) ; +#21249 = PLANE ( 'NONE', #77715 ) ; +#21250 = ORIENTED_EDGE ( 'NONE', *, *, #30122, .T. ) ; +#21251 = ORIENTED_EDGE ( 'NONE', *, *, #31289, .F. ) ; +#21252 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21254 = SURFACE_SIDE_STYLE ('',( #66225 ) ) ; +#21253 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28918 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47647, #2200, #9257 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21255 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#21256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21257 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21258 = ADVANCED_FACE ( 'NONE', ( #37966 ), #53782, .T. ) ; +#21259 = ORIENTED_EDGE ( 'NONE', *, *, #95454, .F. ) ; +#21260 = ORIENTED_EDGE ( 'NONE', *, *, #73090, .T. ) ; +#21261 = ADVANCED_FACE ( 'NONE', ( #31809 ), #70825, .F. ) ; +#21262 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91330 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97420, #44806, #5969 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21263 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21264 = EDGE_LOOP ( 'NONE', ( #17574, #89749, #26213, #97606 ) ) ; +#21265 = SURFACE_SIDE_STYLE ('',( #69722 ) ) ; +#21266 = VECTOR ( 'NONE', #72332, 1000.000000000000000 ) ; +#21267 = EDGE_CURVE ( 'NONE', #67231, #86575, #47856, .T. ) ; +#21268 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21269 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21271 = ORIENTED_EDGE ( 'NONE', *, *, #47163, .T. ) ; +#21270 = ORIENTED_EDGE ( 'NONE', *, *, #17112, .F. ) ; +#21272 = STYLED_ITEM ( 'NONE', ( #65623 ), #69365 ) ; +#21273 = AXIS2_PLACEMENT_3D ( 'NONE', #73100, #33301, #58820 ) ; +#21274 = ORIENTED_EDGE ( 'NONE', *, *, #82821, .F. ) ; +#21275 = CYLINDRICAL_SURFACE ( 'NONE', #31213, 0.1200000000000000927 ) ; +#21276 = LINE ( 'NONE', #20265, #68676 ) ; +#21277 = EDGE_CURVE ( 'NONE', #49566, #50596, #33566, .T. ) ; +#21278 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3519, 'distance_accuracy_value', 'NONE'); +#21279 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21281 = CARTESIAN_POINT ( 'NONE', ( 1.320874515982729980, -0.9101533448649530289, 0.8100000000000000533 ) ) ; +#21280 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#21282 = PLANE ( 'NONE', #25216 ) ; +#21283 = MANIFOLD_SOLID_BREP ( 'ÊäÈë50', #67988 ) ; +#21284 = EDGE_CURVE ( 'NONE', #34176, #84573, #71847, .T. ) ; +#21285 = LINE ( 'NONE', #92699, #24536 ) ; +#21286 = CARTESIAN_POINT ( 'NONE', ( -1.289503315023140084, -0.9165513359838141083, 0.8299999999999999600 ) ) ; +#21287 = STYLED_ITEM ( 'NONE', ( #98260 ), #51428 ) ; +#21288 = EDGE_LOOP ( 'NONE', ( #2870, #36292, #8747, #14232 ) ) ; +#21290 = LINE ( 'NONE', #14089, #24084 ) ; +#21289 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21291 = ORIENTED_EDGE ( 'NONE', *, *, #97976, .F. ) ; +#21292 = ORIENTED_EDGE ( 'NONE', *, *, #88221, .F. ) ; +#21293 = STYLED_ITEM ( 'NONE', ( #94168 ), #10205 ) ; +#21294 = CARTESIAN_POINT ( 'NONE', ( 1.258996483356980001, -1.238505293396390039, 0.8299999999999999600 ) ) ; +#21295 = ADVANCED_FACE ( 'NONE', ( #24907 ), #7942, .T. ) ; +#21296 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#21297 = ADVANCED_FACE ( 'NONE', ( #94282 ), #95283, .T. ) ; +#21298 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21301 = VERTEX_POINT ( 'NONE', #81037 ) ; +#21300 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29466 ) ) ; +#21299 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21302 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21303 = SURFACE_STYLE_USAGE ( .BOTH. , #91254 ) ; +#21304 = LINE ( 'NONE', #7406, #68535 ) ; +#21305 = VERTEX_POINT ( 'NONE', #42708 ) ; +#21307 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21306 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998898659, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#21308 = FILL_AREA_STYLE_COLOUR ( '', #78777 ) ; +#21309 = VERTEX_POINT ( 'NONE', #96299 ) ; +#21310 = ORIENTED_EDGE ( 'NONE', *, *, #932, .F. ) ; +#21312 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 3.159949000000000119, 0.8648700000000000276 ) ) ; +#21311 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#21313 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#21314 = LINE ( 'NONE', #84107, #36871 ) ; +#21315 = SURFACE_STYLE_FILL_AREA ( #28974 ) ; +#21316 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51435 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62163, #31488, #94250 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21317 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8179 ), #73517 ) ; +#21318 = PRESENTATION_STYLE_ASSIGNMENT (( #20306 ) ) ; +#21319 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21320 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #21442, #52113 ), + ( #20438, #60292 ), + ( #37785, #83252 ), + ( #51115, #43924 ), + ( #99464, #43426 ), + ( #91395, #83747 ), + ( #29602, #75095 ), + ( #59803, #13211 ), + ( #82251, #28606 ), + ( #5090, #60781 ), + ( #91885, #67400 ), + ( #76564, #21945 ), + ( #6563, #44404 ), + ( #58789, #12203 ), + ( #75574, #89885 ), + ( #98470, #74586 ), + ( #4609, #31623 ), + ( #8543, #94392 ), + ( #38778, #39790 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06270017598358079702, 0.1256167466604170002, 0.1889113015218140124, 0.2532600040886919812, 0.3171200007542330224, 0.3795159633805619825, 0.4405409028601919852, 0.5009929936201289458, 0.5609495532032110487, 0.6202221492738739794, 0.6797704147043319711, 0.7398130537205910295, 0.8009914761313710052, 0.8641828753275350161, 0.9298363305113630517, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21321 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#21322 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#21323 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21324 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92989 ) ) ; +#21325 = VERTEX_POINT ( 'NONE', #90681 ) ; +#21326 = EDGE_CURVE ( 'NONE', #11036, #47305, #19728, .T. ) ; +#21327 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21328 = EDGE_LOOP ( 'NONE', ( #99042, #12818, #17831, #72376, #60612 ) ) ; +#21329 = SURFACE_SIDE_STYLE ('',( #37175 ) ) ; +#21330 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95198 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30550, #68857, #23439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21331 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000000410, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#21332 = VECTOR ( 'NONE', #9318, 1000.000000000000000 ) ; +#21333 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21334 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21335 = LINE ( 'NONE', #44789, #27153 ) ; +#21336 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#21337 = EDGE_CURVE ( 'NONE', #73556, #55814, #88666, .T. ) ; +#21338 = ORIENTED_EDGE ( 'NONE', *, *, #95091, .T. ) ; +#21339 = STYLED_ITEM ( 'NONE', ( #13047 ), #6944 ) ; +#21340 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21341 = CARTESIAN_POINT ( 'NONE', ( 0.2777831599446540234, -0.9154070317056139938, 0.8100000000000000533 ) ) ; +#21342 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#21343 = FILL_AREA_STYLE ('',( #100335 ) ) ; +#21344 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19754 ) ) ; +#21345 = EDGE_CURVE ( 'NONE', #42288, #93449, #52731, .T. ) ; +#21346 = VECTOR ( 'NONE', #29737, 1000.000000000000000 ) ; +#21347 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21348 = ADVANCED_FACE ( 'NONE', ( #50893 ), #81553, .T. ) ; +#21349 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21350 = VECTOR ( 'NONE', #49583, 1000.000000000000000 ) ; +#21351 = PRESENTATION_STYLE_ASSIGNMENT (( #84645 ) ) ; +#21352 = ORIENTED_EDGE ( 'NONE', *, *, #3206, .F. ) ; +#21353 = FILL_AREA_STYLE ('',( #5976 ) ) ; +#21354 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#21355 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21356 = VERTEX_POINT ( 'NONE', #41716 ) ; +#21357 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21358 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#21359 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21360 = FILL_AREA_STYLE ('',( #52031 ) ) ; +#21361 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75176 ), #34378 ) ; +#21362 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21363 = LINE ( 'NONE', #13635, #30171 ) ; +#21364 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21366 = EDGE_CURVE ( 'NONE', #46653, #45110, #43196, .T. ) ; +#21365 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70709 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15194, #38731, #94343 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21368 = EDGE_CURVE ( 'NONE', #86178, #51654, #4881, .T. ) ; +#21367 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5014 ), #80076 ) ; +#21369 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#21370 = EDGE_LOOP ( 'NONE', ( #45613, #45543, #60893, #23763 ) ) ; +#21371 = SURFACE_STYLE_USAGE ( .BOTH. , #75498 ) ; +#21372 = SURFACE_STYLE_FILL_AREA ( #12646 ) ; +#21373 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21374 = FACE_OUTER_BOUND ( 'NONE', #25480, .T. ) ; +#21375 = SURFACE_STYLE_FILL_AREA ( #67815 ) ; +#21376 = SURFACE_STYLE_FILL_AREA ( #68338 ) ; +#21377 = EDGE_CURVE ( 'NONE', #90815, #29842, #42727, .T. ) ; +#21378 = CARTESIAN_POINT ( 'NONE', ( 0.03998790821699950426, -1.159166046878729706, 0.8100000000000081579 ) ) ; +#21379 = ORIENTED_EDGE ( 'NONE', *, *, #41823, .F. ) ; +#21380 = ORIENTED_EDGE ( 'NONE', *, *, #25352, .F. ) ; +#21381 = EDGE_CURVE ( 'NONE', #46252, #39192, #28393, .T. ) ; +#21382 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76772 ) ) ; +#21383 = AXIS2_PLACEMENT_3D ( 'NONE', #63974, #95575, #56352 ) ; +#21384 = ORIENTED_EDGE ( 'NONE', *, *, #60258, .F. ) ; +#21385 = CARTESIAN_POINT ( 'NONE', ( -0.2587106361308370017, -1.457888621141530061, 0.8299999999999999600 ) ) ; +#21386 = ADVANCED_FACE ( 'NONE', ( #75847 ), #29875, .T. ) ; +#21387 = PLANE ( 'NONE', #53294 ) ; +#21388 = CARTESIAN_POINT ( 'NONE', ( 7.895183000000000284, 10.29465700000000083, 0.8991599999999999593 ) ) ; +#21389 = SURFACE_STYLE_FILL_AREA ( #1826 ) ; +#21390 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70289 ), #29555 ) ; +#21391 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48628 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26280, #81423, #88544 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21392 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #74319, #73337 ) ; +#21393 = CARTESIAN_POINT ( 'NONE', ( -0.03833079888456294992, 0.6936090914190194967, 0.8100000000000000533 ) ) ; +#21394 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#21396 = EDGE_LOOP ( 'NONE', ( #40031, #16943, #39113, #37912 ) ) ; +#21395 = VERTEX_POINT ( 'NONE', #20724 ) ; +#21397 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54963 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99937, #37782, #31117 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21398 = VECTOR ( 'NONE', #43169, 1000.000000000000114 ) ; +#21399 = VERTEX_POINT ( 'NONE', #46175 ) ; +#21400 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#21401 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31170 ) ) ; +#21402 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100816, 'distance_accuracy_value', 'NONE'); +#21404 = LINE ( 'NONE', #60255, #69074 ) ; +#21403 = LINE ( 'NONE', #27588, #52231 ) ; +#21405 = ORIENTED_EDGE ( 'NONE', *, *, #53602, .F. ) ; +#21406 = ORIENTED_EDGE ( 'NONE', *, *, #91233, .T. ) ; +#21407 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86572 ), #52403 ) ; +#21408 = DIRECTION ( 'NONE', ( -1.000000000000000000, 2.478176394252580155E-16, 0.000000000000000000 ) ) ; +#21409 = EDGE_CURVE ( 'NONE', #99864, #11455, #22739, .T. ) ; +#21410 = LINE ( 'NONE', #59772, #13679 ) ; +#21412 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21411 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4000 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62324, #40861, #81572 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21413 = SURFACE_SIDE_STYLE ('',( #13178 ) ) ; +#21414 = ORIENTED_EDGE ( 'NONE', *, *, #37764, .F. ) ; +#21415 = FACE_OUTER_BOUND ( 'NONE', #57630, .T. ) ; +#21416 = VERTEX_POINT ( 'NONE', #99249 ) ; +#21417 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.5238200612200850648, 0.000000000000000000 ) ) ; +#21418 = EDGE_CURVE ( 'NONE', #54145, #54357, #44684, .T. ) ; +#21419 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21420 = SURFACE_SIDE_STYLE ('',( #49713 ) ) ; +#21421 = EDGE_CURVE ( 'NONE', #15411, #9775, #51889, .T. ) ; +#21422 = AXIS2_PLACEMENT_3D ( 'NONE', #58518, #73305, #11416 ) ; +#21423 = ORIENTED_EDGE ( 'NONE', *, *, #22025, .T. ) ; +#21424 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#21425 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99295, #29439, #100756, #30404 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21426 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#21427 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21428 = EDGE_LOOP ( 'NONE', ( #6418, #40901, #91621, #31696 ) ) ; +#21429 = CARTESIAN_POINT ( 'NONE', ( -0.01180881832068430073, -1.255590633215009966, 0.8100000000000000533 ) ) ; +#21430 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21431 = EDGE_LOOP ( 'NONE', ( #93918, #78657, #6135, #41897 ) ) ; +#21432 = VERTEX_POINT ( 'NONE', #83022 ) ; +#21433 = FACE_OUTER_BOUND ( 'NONE', #63545, .T. ) ; +#21434 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41986 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8446, #23890, #1398 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21435 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11594 ), #3536 ) ; +#21436 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21437 = FILL_AREA_STYLE_COLOUR ( '', #59501 ) ; +#21438 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21439 = ORIENTED_EDGE ( 'NONE', *, *, #39390, .F. ) ; +#21440 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21441 = EDGE_CURVE ( 'NONE', #43512, #72808, #76856, .T. ) ; +#21442 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8100000000000000533 ) ) ; +#21443 = VERTEX_POINT ( 'NONE', #36575 ) ; +#21444 = AXIS2_PLACEMENT_3D ( 'NONE', #77900, #86569, #71761 ) ; +#21445 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21446 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21447 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#21448 = SURFACE_SIDE_STYLE ('',( #7047 ) ) ; +#21449 = FILL_AREA_STYLE_COLOUR ( '', #21798 ) ; +#21450 = SURFACE_STYLE_USAGE ( .BOTH. , #100437 ) ; +#21451 = EDGE_CURVE ( 'NONE', #87344, #92575, #45177, .T. ) ; +#21452 = SURFACE_STYLE_FILL_AREA ( #28135 ) ; +#21453 = MANIFOLD_SOLID_BREP ( 'ÊäÈë2', #82676 ) ; +#21454 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#21455 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21457 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21456 = SURFACE_SIDE_STYLE ('',( #91410 ) ) ; +#21458 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21459 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.100000000000000533, 0.8299999999999999600 ) ) ; +#21460 = EDGE_CURVE ( 'NONE', #52824, #79206, #48760, .T. ) ; +#21461 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8648700000000000276 ) ) ; +#21462 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18152 ) ) ; +#21463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21465 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#21464 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21466 = SURFACE_SIDE_STYLE ('',( #51132 ) ) ; +#21467 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#21468 = EDGE_CURVE ( 'NONE', #72146, #1595, #67663, .T. ) ; +#21469 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57438 ), #5179 ) ; +#21470 = AXIS2_PLACEMENT_3D ( 'NONE', #90918, #12215, #50140 ) ; +#21471 = ORIENTED_EDGE ( 'NONE', *, *, #21099, .T. ) ; +#21472 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#21473 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30106, 'distance_accuracy_value', 'NONE'); +#21474 = FACE_OUTER_BOUND ( 'NONE', #85503, .T. ) ; +#21475 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82812, #99031, #82324, #89959 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21476 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#21477 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21478 = VECTOR ( 'NONE', #35217, 1000.000000000000000 ) ; +#21479 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21480 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21481 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21482 = ADVANCED_FACE ( 'NONE', ( #55423 ), #46703, .F. ) ; +#21483 = ADVANCED_FACE ( 'NONE', ( #70700 ), #94665, .F. ) ; +#21484 = ORIENTED_EDGE ( 'NONE', *, *, #46785, .F. ) ; +#21485 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#21486 = ORIENTED_EDGE ( 'NONE', *, *, #85806, .T. ) ; +#21488 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74378, 'distance_accuracy_value', 'NONE'); +#21487 = VECTOR ( 'NONE', #5302, 1000.000000000000000 ) ; +#21489 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59942, 'distance_accuracy_value', 'NONE'); +#21490 = ADVANCED_FACE ( 'NONE', ( #71207 ), #31397, .T. ) ; +#21491 = ADVANCED_FACE ( 'NONE', ( #17566 ), #87043, .T. ) ; +#21492 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21493 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21494 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21495 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#21496 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#21497 = STYLED_ITEM ( 'NONE', ( #7229 ), #52598 ) ; +#21498 = EDGE_LOOP ( 'NONE', ( #46317, #23053, #63367, #9139, #11648, #38721, #64353, #56749 ) ) ; +#21499 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, 0.000000000000000000 ) ) ; +#21500 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#21501 = VERTEX_POINT ( 'NONE', #35461 ) ; +#21502 = ADVANCED_FACE ( 'NONE', ( #19599 ), #97181, .T. ) ; +#21503 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1920 ) ) ; +#21504 = DIRECTION ( 'NONE', ( 0.7071067811865465735, -0.7071067811865484609, 0.000000000000000000 ) ) ; +#21505 = EDGE_LOOP ( 'NONE', ( #65906, #74121, #93840, #42673 ) ) ; +#21506 = EDGE_CURVE ( 'NONE', #45276, #65839, #45032, .T. ) ; +#21507 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100220 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61388, #14834, #54727 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21508 = FILL_AREA_STYLE_COLOUR ( '', #15944 ) ; +#21509 = LINE ( 'NONE', #13793, #75632 ) ; +#21510 = LINE ( 'NONE', #67948, #39732 ) ; +#21511 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21512 = SURFACE_SIDE_STYLE ('',( #74656 ) ) ; +#21513 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.600000000000000089, -13.35000000000000142 ) ) ; +#21515 = ORIENTED_EDGE ( 'NONE', *, *, #49392, .F. ) ; +#21514 = ORIENTED_EDGE ( 'NONE', *, *, #5280, .T. ) ; +#21516 = VECTOR ( 'NONE', #99167, 1000.000000000000000 ) ; +#21517 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.008431457505076202924, 0.1458578643762690474 ) ) ; +#21518 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21519 = ORIENTED_EDGE ( 'NONE', *, *, #8026, .T. ) ; +#21520 = SURFACE_STYLE_USAGE ( .BOTH. , #7114 ) ; +#21522 = CARTESIAN_POINT ( 'NONE', ( -0.5047584000990159581, -0.9806916243805300359, 0.8100000000000000533 ) ) ; +#21521 = PLANE ( 'NONE', #45739 ) ; +#21523 = VERTEX_POINT ( 'NONE', #65550 ) ; +#21524 = ORIENTED_EDGE ( 'NONE', *, *, #35865, .T. ) ; +#21525 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21526 = FILL_AREA_STYLE ('',( #28204 ) ) ; +#21527 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65545 ) ) ; +#21528 = PRESENTATION_STYLE_ASSIGNMENT (( #14824 ) ) ; +#21529 = FACE_OUTER_BOUND ( 'NONE', #64236, .T. ) ; +#21530 = PLANE ( 'NONE', #74549 ) ; +#21531 = VERTEX_POINT ( 'NONE', #11356 ) ; +#21532 = ORIENTED_EDGE ( 'NONE', *, *, #24706, .T. ) ; +#21533 = EDGE_LOOP ( 'NONE', ( #11713, #34272, #30808, #50994 ) ) ; +#21534 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42686 ) ) ; +#21535 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.383333333333330195, 1.747825839084982648E-76 ) ) ; +#21536 = EDGE_CURVE ( 'NONE', #63871, #5017, #27796, .T. ) ; +#21537 = AXIS2_PLACEMENT_3D ( 'NONE', #3713, #13295, #90993 ) ; +#21538 = ORIENTED_EDGE ( 'NONE', *, *, #47191, .T. ) ; +#21539 = VECTOR ( 'NONE', #52008, 1000.000000000000114 ) ; +#21540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21541 = SURFACE_SIDE_STYLE ('',( #28220 ) ) ; +#21542 = VECTOR ( 'NONE', #1841, 999.9999999999998863 ) ; +#21543 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21544 = LINE ( 'NONE', #39893, #47199 ) ; +#21545 = ORIENTED_EDGE ( 'NONE', *, *, #57349, .T. ) ; +#21546 = EDGE_CURVE ( 'NONE', #61650, #61919, #74739, .T. ) ; +#21547 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.100000000000000089, 1.046837090475817223E-78 ) ) ; +#21548 = PLANE ( 'NONE', #65590 ) ; +#21549 = EDGE_LOOP ( 'NONE', ( #77795, #56611, #33003, #39058 ) ) ; +#21550 = CARTESIAN_POINT ( 'NONE', ( 0.04001441731020210363, -0.9622763341455700115, 0.8299999999999988498 ) ) ; +#21551 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#21553 = ORIENTED_EDGE ( 'NONE', *, *, #10033, .T. ) ; +#21552 = FILL_AREA_STYLE_COLOUR ( '', #29754 ) ; +#21554 = FILL_AREA_STYLE_COLOUR ( '', #73503 ) ; +#21555 = CARTESIAN_POINT ( 'NONE', ( 1.823120247820650297, -1.344848644821849959, 0.8299999999999999600 ) ) ; +#21556 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8422 ) ) ; +#21558 = PRESENTATION_STYLE_ASSIGNMENT (( #92001 ) ) ; +#21557 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21559 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21560 = EDGE_CURVE ( 'NONE', #79581, #83746, #88051, .T. ) ; +#21561 = PLANE ( 'NONE', #98311 ) ; +#21562 = ORIENTED_EDGE ( 'NONE', *, *, #57918, .F. ) ; +#21563 = VECTOR ( 'NONE', #4715, 1000.000000000000000 ) ; +#21564 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#21565 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#21566 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21568 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.500000000000000000, 1.869351947278245041E-79 ) ) ; +#21567 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#21569 = EDGE_CURVE ( 'NONE', #57973, #33110, #33949, .T. ) ; +#21570 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52571 ), #86819 ) ; +#21571 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21572 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21573 = ORIENTED_EDGE ( 'NONE', *, *, #10489, .T. ) ; +#21574 = VECTOR ( 'NONE', #74050, 1000.000000000000000 ) ; +#21575 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21576 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#21577 = FACE_OUTER_BOUND ( 'NONE', #55775, .T. ) ; +#21578 = ORIENTED_EDGE ( 'NONE', *, *, #50163, .F. ) ; +#21579 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#21581 = FILL_AREA_STYLE_COLOUR ( '', #13432 ) ; +#21580 = LINE ( 'NONE', #77207, #21346 ) ; +#21582 = CARTESIAN_POINT ( 'NONE', ( 1.667677657188980200, -0.9647878283071119609, 0.8299999999999999600 ) ) ; +#21583 = VECTOR ( 'NONE', #66373, 1000.000000000000000 ) ; +#21584 = EDGE_CURVE ( 'NONE', #67641, #12266, #18580, .T. ) ; +#21585 = SURFACE_STYLE_USAGE ( .BOTH. , #68026 ) ; +#21586 = PLANE ( 'NONE', #95250 ) ; +#21588 = STYLED_ITEM ( 'NONE', ( #50010 ), #19202 ) ; +#21587 = FILL_AREA_STYLE_COLOUR ( '', #64926 ) ; +#21589 = VECTOR ( 'NONE', #35458, 1000.000000000000000 ) ; +#21590 = LINE ( 'NONE', #99110, #29798 ) ; +#21591 = EDGE_CURVE ( 'NONE', #83308, #73910, #42593, .T. ) ; +#21592 = VERTEX_POINT ( 'NONE', #59460 ) ; +#21593 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#21594 = SURFACE_STYLE_USAGE ( .BOTH. , #76216 ) ; +#21595 = SURFACE_STYLE_USAGE ( .BOTH. , #51762 ) ; +#21596 = AXIS2_PLACEMENT_3D ( 'NONE', #5035, #34737, #89337 ) ; +#21597 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#21598 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21599 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#21600 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000533, 0.000000000000000000 ) ) ; +#21601 = AXIS2_PLACEMENT_3D ( 'NONE', #76680, #45498, #86362 ) ; +#21603 = EDGE_CURVE ( 'NONE', #83845, #91883, #91549, .T. ) ; +#21602 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36284 ) ) ; +#21604 = PLANE ( 'NONE', #83546 ) ; +#21605 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100706, 'distance_accuracy_value', 'NONE'); +#21606 = EDGE_CURVE ( 'NONE', #94706, #40037, #92525, .T. ) ; +#21607 = STYLED_ITEM ( 'NONE', ( #42610 ), #96243 ) ; +#21608 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21609 = ORIENTED_EDGE ( 'NONE', *, *, #29693, .T. ) ; +#21610 = SURFACE_STYLE_USAGE ( .BOTH. , #43577 ) ; +#21611 = EDGE_LOOP ( 'NONE', ( #78954, #86705, #31486, #18418 ) ) ; +#21612 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21613 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95312, 'distance_accuracy_value', 'NONE'); +#21614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53852, 'distance_accuracy_value', 'NONE'); +#21615 = EDGE_CURVE ( 'NONE', #10128, #16445, #98622, .T. ) ; +#21616 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52619 ) ) ; +#21617 = FILL_AREA_STYLE ('',( #36451 ) ) ; +#21618 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#21619 = CARTESIAN_POINT ( 'NONE', ( -0.9443983742018540184, -1.435626150595060047, 0.8299999999999981837 ) ) ; +#21620 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#21621 = SURFACE_SIDE_STYLE ('',( #68568 ) ) ; +#21622 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21623 = FILL_AREA_STYLE_COLOUR ( '', #73309 ) ; +#21624 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8100000000000001643 ) ) ; +#21625 = ORIENTED_EDGE ( 'NONE', *, *, #1368, .T. ) ; +#21626 = AXIS2_PLACEMENT_3D ( 'NONE', #75448, #61662, #92738 ) ; +#21627 = MANIFOLD_SOLID_BREP ( 'ÊäÈë160', #20938 ) ; +#21628 = FILL_AREA_STYLE_COLOUR ( '', #46493 ) ; +#21629 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88392, 'distance_accuracy_value', 'NONE'); +#21630 = SURFACE_STYLE_USAGE ( .BOTH. , #59483 ) ; +#21631 = EDGE_CURVE ( 'NONE', #69209, #96590, #35953, .T. ) ; +#21632 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21633 = VERTEX_POINT ( 'NONE', #21108 ) ; +#21634 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21635 = LINE ( 'NONE', #28306, #32092 ) ; +#21636 = ADVANCED_FACE ( 'NONE', ( #13366 ), #51768, .T. ) ; +#21637 = SURFACE_STYLE_FILL_AREA ( #60474 ) ; +#21638 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21639 = FILL_AREA_STYLE_COLOUR ( '', #59572 ) ; +#21641 = ORIENTED_EDGE ( 'NONE', *, *, #54888, .F. ) ; +#21640 = AXIS2_PLACEMENT_3D ( 'NONE', #40418, #80232, #34782 ) ; +#21642 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28153, 'distance_accuracy_value', 'NONE'); +#21643 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#21644 = PLANE ( 'NONE', #93189 ) ; +#21645 = VERTEX_POINT ( 'NONE', #67546 ) ; +#21646 = LINE ( 'NONE', #4328, #77438 ) ; +#21647 = AXIS2_PLACEMENT_3D ( 'NONE', #67530, #74725, #98607 ) ; +#21649 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#21648 = AXIS2_PLACEMENT_3D ( 'NONE', #6481, #69288, #61206 ) ; +#21650 = LINE ( 'NONE', #52807, #87962 ) ; +#21651 = PRESENTATION_STYLE_ASSIGNMENT (( #35629 ) ) ; +#21652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21653 = VERTEX_POINT ( 'NONE', #76729 ) ; +#21654 = FILL_AREA_STYLE_COLOUR ( '', #2560 ) ; +#21655 = AXIS2_PLACEMENT_3D ( 'NONE', #24176, #16443, #47632 ) ; +#21656 = VECTOR ( 'NONE', #74820, 1000.000000000000000 ) ; +#21657 = VERTEX_POINT ( 'NONE', #6698 ) ; +#21659 = ORIENTED_EDGE ( 'NONE', *, *, #12324, .T. ) ; +#21658 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#21660 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#21662 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1199999999999999956, -0.7500000000000000000 ) ) ; +#21661 = STYLED_ITEM ( 'NONE', ( #46290 ), #19304 ) ; +#21663 = VECTOR ( 'NONE', #60811, 1000.000000000000000 ) ; +#21664 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.6999999999999999556, -13.15000000000000036 ) ) ; +#21665 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.123820061220085265, -0.02000000000000000042 ) ) ; +#21666 = ORIENTED_EDGE ( 'NONE', *, *, #12221, .T. ) ; +#21667 = ADVANCED_FACE ( 'NONE', ( #37937 ), #76556, .F. ) ; +#21669 = LINE ( 'NONE', #52825, #61426 ) ; +#21668 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39605 ), #31509 ) ; +#21670 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#21671 = VERTEX_POINT ( 'NONE', #40468 ) ; +#21672 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.8166667230436682745, 0.6665916835684375652 ) ) ; +#21673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21674 = VECTOR ( 'NONE', #78518, 1000.000000000000000 ) ; +#21675 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54101 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54783, #10188, #32775 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21676 = STYLED_ITEM ( 'NONE', ( #26512 ), #35125 ) ; +#21677 = ORIENTED_EDGE ( 'NONE', *, *, #44892, .F. ) ; +#21679 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21678 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21680 = ORIENTED_EDGE ( 'NONE', *, *, #26773, .F. ) ; +#21681 = VECTOR ( 'NONE', #22438, 1000.000000000000000 ) ; +#21682 = STYLED_ITEM ( 'NONE', ( #65448 ), #96639 ) ; +#21684 = SURFACE_SIDE_STYLE ('',( #27870 ) ) ; +#21683 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#21685 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21686 = STYLED_ITEM ( 'NONE', ( #92826 ), #59716 ) ; +#21687 = VECTOR ( 'NONE', #236, 1000.000000000000114 ) ; +#21688 = CARTESIAN_POINT ( 'NONE', ( 0.1662790904141970283, -1.409021472795120022, 0.8299999999999982947 ) ) ; +#21689 = ORIENTED_EDGE ( 'NONE', *, *, #92221, .F. ) ; +#21690 = ORIENTED_EDGE ( 'NONE', *, *, #78231, .T. ) ; +#21691 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21692 = SURFACE_STYLE_USAGE ( .BOTH. , #38527 ) ; +#21693 = LINE ( 'NONE', #5333, #81716 ) ; +#21694 = LINE ( 'NONE', #53850, #52811 ) ; +#21695 = FACE_OUTER_BOUND ( 'NONE', #61273, .T. ) ; +#21696 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21697 = PRESENTATION_STYLE_ASSIGNMENT (( #36546 ) ) ; +#21698 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#21699 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21700 = VERTEX_POINT ( 'NONE', #1663 ) ; +#21701 = PLANE ( 'NONE', #4119 ) ; +#21702 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#21703 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21704 = LINE ( 'NONE', #75836, #15282 ) ; +#21705 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21706 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#21707 = ORIENTED_EDGE ( 'NONE', *, *, #92442, .T. ) ; +#21708 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21709 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21710 = FILL_AREA_STYLE ('',( #45666 ) ) ; +#21711 = CARTESIAN_POINT ( 'NONE', ( -0.1013823343696960005, -1.445184491613219935, 0.8299999999999999600 ) ) ; +#21712 = CIRCLE ( 'NONE', #57629, 0.009999999999999998473 ) ; +#21713 = FACE_OUTER_BOUND ( 'NONE', #44496, .T. ) ; +#21714 = SURFACE_STYLE_USAGE ( .BOTH. , #38059 ) ; +#21715 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75989, #43839, #28525, #58704 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21716 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671291000000000082, 0.8991599999999999593 ) ) ; +#21717 = SURFACE_STYLE_USAGE ( .BOTH. , #98750 ) ; +#21718 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67415 ), #2218 ) ; +#21719 = VECTOR ( 'NONE', #22648, 1000.000000000000000 ) ; +#21720 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21721 = FILL_AREA_STYLE_COLOUR ( '', #10839 ) ; +#21722 = SURFACE_SIDE_STYLE ('',( #75352 ) ) ; +#21723 = LINE ( 'NONE', #91659, #97839 ) ; +#21724 = SURFACE_SIDE_STYLE ('',( #23256 ) ) ; +#21725 = FACE_OUTER_BOUND ( 'NONE', #41877, .T. ) ; +#21726 = VECTOR ( 'NONE', #57395, 1000.000000000000000 ) ; +#21728 = EDGE_CURVE ( 'NONE', #86226, #299, #95039, .T. ) ; +#21727 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#21729 = PLANE ( 'NONE', #11090 ) ; +#21730 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94071, 'distance_accuracy_value', 'NONE'); +#21731 = FACE_OUTER_BOUND ( 'NONE', #54543, .T. ) ; +#21732 = PRESENTATION_STYLE_ASSIGNMENT (( #13501 ) ) ; +#21733 = AXIS2_PLACEMENT_3D ( 'NONE', #77098, #20079, #97166 ) ; +#21734 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31506 ), #77190 ) ; +#21735 = LINE ( 'NONE', #52400, #48717 ) ; +#21736 = CYLINDRICAL_SURFACE ( 'NONE', #43457, 0.05000000000000012768 ) ; +#21737 = PLANE ( 'NONE', #92703 ) ; +#21738 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80506 ), #593 ) ; +#21739 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21740 = ORIENTED_EDGE ( 'NONE', *, *, #29338, .F. ) ; +#21741 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17439, 'distance_accuracy_value', 'NONE'); +#21742 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11812 ) ) ; +#21743 = CIRCLE ( 'NONE', #67371, 0.05000000000000002359 ) ; +#21744 = PLANE ( 'NONE', #19318 ) ; +#21745 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#21746 = AXIS2_PLACEMENT_3D ( 'NONE', #82132, #12076, #82621 ) ; +#21747 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88065 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68646, #75827, #100194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21748 = EDGE_CURVE ( 'NONE', #83336, #24220, #17443, .T. ) ; +#21749 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8613 ) ) ; +#21750 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21751 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#21752 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21753 = AXIS2_PLACEMENT_3D ( 'NONE', #47423, #94857, #87738 ) ; +#21754 = VERTEX_POINT ( 'NONE', #61941 ) ; +#21755 = FILL_AREA_STYLE_COLOUR ( '', #67688 ) ; +#21756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85763 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70690, #85505, #93628 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21757 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93499, 'distance_accuracy_value', 'NONE'); +#21758 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41630 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50967, #90746, #83604 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21759 = CARTESIAN_POINT ( 'NONE', ( -0.1013823343696960005, -1.445184491613219935, 0.8300000000000006262 ) ) ; +#21760 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21761 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#21762 = ORIENTED_EDGE ( 'NONE', *, *, #82376, .F. ) ; +#21763 = VERTEX_POINT ( 'NONE', #54270 ) ; +#21764 = SURFACE_SIDE_STYLE ('',( #83567 ) ) ; +#21766 = FACE_OUTER_BOUND ( 'NONE', #93929, .T. ) ; +#21765 = SURFACE_SIDE_STYLE ('',( #94589 ) ) ; +#21767 = STYLED_ITEM ( 'NONE', ( #14929 ), #67365 ) ; +#21768 = ORIENTED_EDGE ( 'NONE', *, *, #70827, .F. ) ; +#21769 = FACE_OUTER_BOUND ( 'NONE', #72177, .T. ) ; +#21770 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#21771 = CARTESIAN_POINT ( 'NONE', ( 0.4905624295734890006, -1.210065939746389985, 0.8100000000000000533 ) ) ; +#21772 = LINE ( 'NONE', #36618, #48431 ) ; +#21773 = SURFACE_SIDE_STYLE ('',( #100265 ) ) ; +#21774 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #57435, #85773 ) ; +#21775 = EDGE_CURVE ( 'NONE', #79553, #44056, #93523, .T. ) ; +#21776 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5049 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49814, #96222, #96719 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21777 = ORIENTED_EDGE ( 'NONE', *, *, #96479, .T. ) ; +#21778 = ORIENTED_EDGE ( 'NONE', *, *, #9646, .T. ) ; +#21779 = SURFACE_STYLE_USAGE ( .BOTH. , #20264 ) ; +#21780 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#21781 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21782 = FILL_AREA_STYLE ('',( #52443 ) ) ; +#21783 = EDGE_CURVE ( 'NONE', #48000, #67267, #42477, .T. ) ; +#21784 = FACE_OUTER_BOUND ( 'NONE', #81326, .T. ) ; +#21785 = SURFACE_SIDE_STYLE ('',( #91719 ) ) ; +#21786 = AXIS2_PLACEMENT_3D ( 'NONE', #12340, #4746, #37914 ) ; +#21787 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.000000000000000000 ) ) ; +#21788 = ORIENTED_EDGE ( 'NONE', *, *, #70204, .T. ) ; +#21790 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21789 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21791 = VECTOR ( 'NONE', #22628, 1000.000000000000000 ) ; +#21792 = EDGE_LOOP ( 'NONE', ( #26609, #63511, #16203, #47882 ) ) ; +#21793 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33258 ) ) ; +#21794 = ORIENTED_EDGE ( 'NONE', *, *, #57660, .F. ) ; +#21795 = CARTESIAN_POINT ( 'NONE', ( 1.289721710971190038, -1.248384608377719918, 0.8299999999999999600 ) ) ; +#21796 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21797 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#21798 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21799 = FILL_AREA_STYLE_COLOUR ( '', #75066 ) ; +#21801 = ORIENTED_EDGE ( 'NONE', *, *, #39699, .F. ) ; +#21800 = PRESENTATION_STYLE_ASSIGNMENT (( #98820 ) ) ; +#21802 = FACE_OUTER_BOUND ( 'NONE', #70781, .T. ) ; +#21803 = SURFACE_STYLE_USAGE ( .BOTH. , #84093 ) ; +#21804 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.000000000000000000 ) ) ; +#21805 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21806 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #588 ) ) ; +#21807 = ORIENTED_EDGE ( 'NONE', *, *, #40899, .F. ) ; +#21809 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21808 = LINE ( 'NONE', #52982, #30214 ) ; +#21810 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21811 = ORIENTED_EDGE ( 'NONE', *, *, #33489, .F. ) ; +#21812 = VERTEX_POINT ( 'NONE', #58329 ) ; +#21813 = FILL_AREA_STYLE ('',( #29478 ) ) ; +#21815 = LINE ( 'NONE', #44769, #1474 ) ; +#21814 = CARTESIAN_POINT ( 'NONE', ( 1.049748415576440053, -1.475020827802409951, 0.8299999999999999600 ) ) ; +#21816 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21817 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#21818 = SURFACE_STYLE_USAGE ( .BOTH. , #91743 ) ; +#21819 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16908 ), #78895 ) ; +#21820 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#21821 = FILL_AREA_STYLE ('',( #67273 ) ) ; +#21822 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#21823 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14193 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63554, #87019, #91897 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21825 = EDGE_CURVE ( 'NONE', #94479, #30515, #10725, .T. ) ; +#21824 = SURFACE_SIDE_STYLE ('',( #68760 ) ) ; +#21826 = VECTOR ( 'NONE', #15180, 1000.000000000000000 ) ; +#21827 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21828 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21829 = VECTOR ( 'NONE', #54435, 1000.000000000000000 ) ; +#21830 = EDGE_LOOP ( 'NONE', ( #71157, #94929, #85182, #51114, #97525 ) ) ; +#21831 = VERTEX_POINT ( 'NONE', #80279 ) ; +#21832 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#21833 = CARTESIAN_POINT ( 'NONE', ( -0.1025235689449880000, -0.9625006208768249749, 0.8299999999999999600 ) ) ; +#21834 = CARTESIAN_POINT ( 'NONE', ( 1.095142431513040027, -1.118172950060400073, 0.8100000000000000533 ) ) ; +#21835 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21836 = CIRCLE ( 'NONE', #34913, 0.009999999999999998473 ) ; +#21837 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.000000000000000000 ) ) ; +#21838 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#21839 = PRESENTATION_STYLE_ASSIGNMENT (( #7438 ) ) ; +#21840 = EDGE_CURVE ( 'NONE', #7985, #72282, #82865, .T. ) ; +#21841 = VERTEX_POINT ( 'NONE', #73611 ) ; +#21842 = EDGE_CURVE ( 'NONE', #37922, #57093, #96932, .T. ) ; +#21843 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21844 = SURFACE_SIDE_STYLE ('',( #22862 ) ) ; +#21845 = FACE_BOUND ( 'NONE', #41936, .T. ) ; +#21846 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#21847 = AXIS2_PLACEMENT_3D ( 'NONE', #76138, #85807, #68460 ) ; +#21848 = SURFACE_STYLE_USAGE ( .BOTH. , #22868 ) ; +#21849 = CARTESIAN_POINT ( 'NONE', ( 1.886527894060100019, -1.258231835375339891, 0.8299999999999999600 ) ) ; +#21850 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21851 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#21852 = PRESENTATION_STYLE_ASSIGNMENT (( #70317 ) ) ; +#21853 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21854 = PLANE ( 'NONE', #38980 ) ; +#21855 = VECTOR ( 'NONE', #16896, 1000.000000000000000 ) ; +#21856 = SURFACE_SIDE_STYLE ('',( #82161 ) ) ; +#21857 = PLANE ( 'NONE', #74084 ) ; +#21858 = EDGE_CURVE ( 'NONE', #89489, #37342, #33818, .T. ) ; +#21859 = PLANE ( 'NONE', #61707 ) ; +#21860 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81808, 'distance_accuracy_value', 'NONE'); +#21861 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#21862 = CARTESIAN_POINT ( 'NONE', ( -1.016666666666666829, -3.099999999999989875, 0.000000000000000000 ) ) ; +#21863 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8099999999999416556 ) ) ; +#21864 = VERTEX_POINT ( 'NONE', #34834 ) ; +#21865 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21866 = CARTESIAN_POINT ( 'NONE', ( 1.608267340221630093, -1.417598257925390293, 0.8299999999999977396 ) ) ; +#21867 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52850 ), #61027 ) ; +#21868 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21327, 'distance_accuracy_value', 'NONE'); +#21869 = LINE ( 'NONE', #45814, #26397 ) ; +#21870 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21871 = STYLED_ITEM ( 'NONE', ( #37567 ), #26602 ) ; +#21872 = ADVANCED_FACE ( 'NONE', ( #3658 ), #18966, .F. ) ; +#21873 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8100000000000001643 ) ) ; +#21874 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#21875 = EDGE_LOOP ( 'NONE', ( #56063, #33955, #79811, #40340, #37412, #35379 ) ) ; +#21877 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100036 ) ) ; +#21876 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21878 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85047, #15053, #46210, #7867 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#21879 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21880 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30675, 'distance_accuracy_value', 'NONE'); +#21881 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #900 ) ) ; +#21882 = VECTOR ( 'NONE', #9483, 1000.000000000000000 ) ; +#21883 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90054, 'distance_accuracy_value', 'NONE'); +#21884 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#21885 = ORIENTED_EDGE ( 'NONE', *, *, #50354, .F. ) ; +#21886 = VERTEX_POINT ( 'NONE', #42960 ) ; +#21887 = STYLED_ITEM ( 'NONE', ( #57411 ), #28962 ) ; +#21888 = STYLED_ITEM ( 'NONE', ( #78592 ), #98307 ) ; +#21889 = PLANE ( 'NONE', #38985 ) ; +#21890 = ORIENTED_EDGE ( 'NONE', *, *, #82360, .T. ) ; +#21891 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853417210, 1.551146575926969806, 0.8100000000000001643 ) ) ; +#21893 = FACE_OUTER_BOUND ( 'NONE', #97770, .T. ) ; +#21892 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75757 ) ) ; +#21894 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#21895 = CYLINDRICAL_SURFACE ( 'NONE', #72825, 0.05000000000000012768 ) ; +#21896 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13754 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80823, #17975, #50690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21897 = SURFACE_SIDE_STYLE ('',( #75040 ) ) ; +#21898 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65941 ), #34985 ) ; +#21899 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999833, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#21900 = EDGE_CURVE ( 'NONE', #31439, #2547, #7144, .T. ) ; +#21901 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#21903 = ORIENTED_EDGE ( 'NONE', *, *, #70045, .T. ) ; +#21902 = VERTEX_POINT ( 'NONE', #58832 ) ; +#21904 = VERTEX_POINT ( 'NONE', #79778 ) ; +#21905 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.000000000000000000 ) ) ; +#21906 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21907 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65947 ) ) ; +#21908 = ORIENTED_EDGE ( 'NONE', *, *, #92772, .T. ) ; +#21909 = EDGE_CURVE ( 'NONE', #63306, #1291, #95544, .T. ) ; +#21910 = ORIENTED_EDGE ( 'NONE', *, *, #55301, .T. ) ; +#21911 = SURFACE_SIDE_STYLE ('',( #46882 ) ) ; +#21912 = LINE ( 'NONE', #61748, #93573 ) ; +#21913 = PLANE ( 'NONE', #38907 ) ; +#21914 = STYLED_ITEM ( 'NONE', ( #81702 ), #67947 ) ; +#21915 = CARTESIAN_POINT ( 'NONE', ( 9.924579124874954417, 8.109696875125045779, 0.8648700000000000276 ) ) ; +#21916 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4750000000000000333, -0.2400000000000000189 ) ) ; +#21917 = EDGE_CURVE ( 'NONE', #61880, #86528, #93625, .T. ) ; +#21918 = ORIENTED_EDGE ( 'NONE', *, *, #9110, .T. ) ; +#21919 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100353 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47674, #16492, #64514 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21920 = CARTESIAN_POINT ( 'NONE', ( -0.4617362663480760743, -1.013453039847479920, 0.8100000000000000533 ) ) ; +#21921 = ORIENTED_EDGE ( 'NONE', *, *, #55286, .F. ) ; +#21922 = ORIENTED_EDGE ( 'NONE', *, *, #23520, .T. ) ; +#21923 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#21924 = DIRECTION ( 'NONE', ( -0.7071071146859689849, 0.7071064476869689530, 0.000000000000000000 ) ) ; +#21925 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#21928 = ORIENTED_EDGE ( 'NONE', *, *, #47789, .T. ) ; +#21927 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63423, 'distance_accuracy_value', 'NONE'); +#21926 = FILL_AREA_STYLE_COLOUR ( '', #64121 ) ; +#21929 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8099999999999852873 ) ) ; +#21930 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#21931 = VECTOR ( 'NONE', #79748, 1000.000000000000000 ) ; +#21932 = ORIENTED_EDGE ( 'NONE', *, *, #26407, .F. ) ; +#21933 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21934 = LINE ( 'NONE', #85208, #29721 ) ; +#21935 = VERTEX_POINT ( 'NONE', #36321 ) ; +#21936 = ORIENTED_EDGE ( 'NONE', *, *, #92482, .T. ) ; +#21937 = FILL_AREA_STYLE ('',( #67874 ) ) ; +#21938 = SURFACE_SIDE_STYLE ('',( #7531 ) ) ; +#21939 = FACE_OUTER_BOUND ( 'NONE', #88697, .T. ) ; +#21940 = CARTESIAN_POINT ( 'NONE', ( 1.236552921348300194, -1.233317951191559958, 0.8299999999999997380 ) ) ; +#21941 = LINE ( 'NONE', #20949, #8849 ) ; +#21942 = FILL_AREA_STYLE_COLOUR ( '', #16475 ) ; +#21943 = ORIENTED_EDGE ( 'NONE', *, *, #23855, .F. ) ; +#21944 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3947 ) ) ; +#21945 = CARTESIAN_POINT ( 'NONE', ( -0.9573895083907240089, -1.450479623942970253, 0.8299999999999999600 ) ) ; +#21946 = ORIENTED_EDGE ( 'NONE', *, *, #48522, .F. ) ; +#21947 = FILL_AREA_STYLE ('',( #75577 ) ) ; +#21948 = LINE ( 'NONE', #84245, #58188 ) ; +#21949 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#21950 = STYLED_ITEM ( 'NONE', ( #10062 ), #28319 ) ; +#21952 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.000000000000000000 ) ) ; +#21951 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21954 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77330 ), #80658 ) ; +#21953 = CARTESIAN_POINT ( 'NONE', ( 1.799693084787389985, -1.050822088410799937, 0.8299999999999999600 ) ) ; +#21955 = FILL_AREA_STYLE_COLOUR ( '', #81063 ) ; +#21956 = SURFACE_STYLE_USAGE ( .BOTH. , #29132 ) ; +#21957 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21958 = CARTESIAN_POINT ( 'NONE', ( -1.375607183049269988, -1.395425853902759972, 0.8300000000000024025 ) ) ; +#21959 = EDGE_CURVE ( 'NONE', #5956, #59435, #98503, .T. ) ; +#21960 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16604, #97717, #57492 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#21961 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#21962 = CIRCLE ( 'NONE', #57881, 0.009999999999999998473 ) ; +#21963 = LINE ( 'NONE', #88787, #82055 ) ; +#21964 = PRESENTATION_STYLE_ASSIGNMENT (( #83264 ) ) ; +#21965 = PLANE ( 'NONE', #83224 ) ; +#21966 = EDGE_CURVE ( 'NONE', #63952, #63509, #28646, .T. ) ; +#21967 = FILL_AREA_STYLE ('',( #43942 ) ) ; +#21968 = SURFACE_SIDE_STYLE ('',( #92871 ) ) ; +#21969 = PLANE ( 'NONE', #52207 ) ; +#21970 = FILL_AREA_STYLE ('',( #84266 ) ) ; +#21971 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#21972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38237 ), #74104 ) ; +#21973 = EDGE_CURVE ( 'NONE', #38423, #85949, #44933, .T. ) ; +#21974 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61565, 'distance_accuracy_value', 'NONE'); +#21975 = ORIENTED_EDGE ( 'NONE', *, *, #22203, .T. ) ; +#21976 = CARTESIAN_POINT ( 'NONE', ( -1.038348751223719946, -1.423389424083600030, 0.8100000000000000533 ) ) ; +#21977 = SURFACE_STYLE_USAGE ( .BOTH. , #84763 ) ; +#21978 = EDGE_CURVE ( 'NONE', #68842, #14189, #99735, .T. ) ; +#21979 = SURFACE_SIDE_STYLE ('',( #44924 ) ) ; +#21980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21981 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#21982 = SURFACE_STYLE_USAGE ( .BOTH. , #60326 ) ; +#21983 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#21984 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#21985 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#21986 = EDGE_LOOP ( 'NONE', ( #46224, #31848, #28501, #59844 ) ) ; +#21987 = SURFACE_STYLE_FILL_AREA ( #44938 ) ; +#21988 = EDGE_CURVE ( 'NONE', #43549, #30895, #74621, .T. ) ; +#21989 = EDGE_LOOP ( 'NONE', ( #50429, #42823, #44873, #43156 ) ) ; +#21990 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#21991 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#21992 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#21993 = FILL_AREA_STYLE ('',( #13770 ) ) ; +#21994 = FACE_OUTER_BOUND ( 'NONE', #71673, .T. ) ; +#21995 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#21996 = VECTOR ( 'NONE', #28127, 1000.000000000000000 ) ; +#21997 = FILL_AREA_STYLE_COLOUR ( '', #15954 ) ; +#21998 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#21999 = ORIENTED_EDGE ( 'NONE', *, *, #6337, .T. ) ; +#22000 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22001 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#22002 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#22003 = VERTEX_POINT ( 'NONE', #20991 ) ; +#22004 = SURFACE_STYLE_FILL_AREA ( #98523 ) ; +#22005 = VECTOR ( 'NONE', #62250, 1000.000000000000000 ) ; +#22006 = LINE ( 'NONE', #526, #24034 ) ; +#22007 = ORIENTED_EDGE ( 'NONE', *, *, #86150, .T. ) ; +#22008 = VECTOR ( 'NONE', #40651, 1000.000000000000000 ) ; +#22009 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12103 ) ) ; +#22010 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22011 = LINE ( 'NONE', #45457, #99959 ) ; +#22012 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999995337, 0.2500000000000000000, -0.6500000000000001332 ) ) ; +#22013 = EDGE_CURVE ( 'NONE', #19800, #49262, #75745, .T. ) ; +#22014 = VECTOR ( 'NONE', #68218, 1000.000000000000000 ) ; +#22016 = ORIENTED_EDGE ( 'NONE', *, *, #73236, .T. ) ; +#22015 = VERTEX_POINT ( 'NONE', #36818 ) ; +#22017 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22018 = ORIENTED_EDGE ( 'NONE', *, *, #4488, .F. ) ; +#22019 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22020 = STYLED_ITEM ( 'NONE', ( #20093 ), #20397 ) ; +#22021 = VECTOR ( 'NONE', #64320, 1000.000000000000000 ) ; +#22023 = CARTESIAN_POINT ( 'NONE', ( -0.5594783971358769925, -0.9704561130045840089, 0.8100000000000000533 ) ) ; +#22022 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -9.880000000000000782, 0.2999999999999999889 ) ) ; +#22024 = ORIENTED_EDGE ( 'NONE', *, *, #33956, .T. ) ; +#22025 = EDGE_CURVE ( 'NONE', #96487, #74215, #66943, .T. ) ; +#22026 = ORIENTED_EDGE ( 'NONE', *, *, #4151, .T. ) ; +#22028 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59625 ) ) ; +#22027 = DIRECTION ( 'NONE', ( -0.7071062811861726916, -0.7071072811865688479, 0.000000000000000000 ) ) ; +#22029 = PRESENTATION_STYLE_ASSIGNMENT (( #92939 ) ) ; +#22030 = VECTOR ( 'NONE', #74234, 1000.000000000000000 ) ; +#22031 = FILL_AREA_STYLE_COLOUR ( '', #55193 ) ; +#22032 = SURFACE_STYLE_USAGE ( .BOTH. , #14325 ) ; +#22033 = FILL_AREA_STYLE ('',( #91970 ) ) ; +#22034 = ORIENTED_EDGE ( 'NONE', *, *, #79255, .F. ) ; +#22035 = ADVANCED_FACE ( 'NONE', ( #75126 ), #90427, .T. ) ; +#22036 = ORIENTED_EDGE ( 'NONE', *, *, #81405, .F. ) ; +#22037 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8648700000000000276 ) ) ; +#22038 = ORIENTED_EDGE ( 'NONE', *, *, #99107, .T. ) ; +#22039 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90556 ) ) ; +#22040 = SURFACE_SIDE_STYLE ('',( #5672 ) ) ; +#22042 = VERTEX_POINT ( 'NONE', #13243 ) ; +#22041 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#22043 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67647 ), #38457 ) ; +#22044 = FILL_AREA_STYLE_COLOUR ( '', #31966 ) ; +#22045 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#22046 = ORIENTED_EDGE ( 'NONE', *, *, #54057, .F. ) ; +#22047 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#22048 = EDGE_LOOP ( 'NONE', ( #27082, #82100, #95309, #6833 ) ) ; +#22049 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22050 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #924 ), #36795 ) ; +#22053 = EDGE_CURVE ( 'NONE', #94101, #66714, #29639, .T. ) ; +#22052 = ORIENTED_EDGE ( 'NONE', *, *, #37693, .T. ) ; +#22051 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.299999999999999822, 1.084224129406308774E-78 ) ) ; +#22054 = EDGE_CURVE ( 'NONE', #92223, #38257, #84280, .T. ) ; +#22055 = CARTESIAN_POINT ( 'NONE', ( 1.391117489400210072, -0.9747981717974689708, 0.8299999999999998490 ) ) ; +#22056 = SURFACE_STYLE_USAGE ( .BOTH. , #62909 ) ; +#22057 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8099999999999502043 ) ) ; +#22058 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#22059 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38330 ), #35151 ) ; +#22060 = SURFACE_SIDE_STYLE ('',( #93485 ) ) ; +#22061 = FACE_OUTER_BOUND ( 'NONE', #547, .T. ) ; +#22062 = ORIENTED_EDGE ( 'NONE', *, *, #65431, .T. ) ; +#22063 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#22064 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15157, #16673, #30485, #46313 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22065 = SURFACE_SIDE_STYLE ('',( #46540 ) ) ; +#22066 = STYLED_ITEM ( 'NONE', ( #46778 ), #83492 ) ; +#22067 = STYLED_ITEM ( 'NONE', ( #10222 ), #89991 ) ; +#22068 = VECTOR ( 'NONE', #97397, 1000.000000000000000 ) ; +#22069 = FILL_AREA_STYLE_COLOUR ( '', #42021 ) ; +#22071 = CARTESIAN_POINT ( 'NONE', ( 1.639423674598250003, -1.436594792639700024, 0.8299999999999999600 ) ) ; +#22070 = CARTESIAN_POINT ( 'NONE', ( 0.4673939658190879864, -1.066920424575050097, 0.8299999999999999600 ) ) ; +#22072 = LINE ( 'NONE', #53236, #40548 ) ; +#22073 = FACE_OUTER_BOUND ( 'NONE', #28588, .T. ) ; +#22075 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22074 = PLANE ( 'NONE', #69414 ) ; +#22076 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71064 ) ) ; +#22077 = EDGE_CURVE ( 'NONE', #9359, #35769, #99983, .T. ) ; +#22078 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #5021, #36715, #91325, #5509 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22079 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#22080 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626904202, 0.1400000000000000133 ) ) ; +#22081 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43224 ), #57998 ) ; +#22082 = ORIENTED_EDGE ( 'NONE', *, *, #96981, .T. ) ; +#22083 = STYLED_ITEM ( 'NONE', ( #73391 ), #48508 ) ; +#22084 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22085 = ORIENTED_EDGE ( 'NONE', *, *, #6882, .F. ) ; +#22086 = VECTOR ( 'NONE', #94970, 1000.000000000000000 ) ; +#22088 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22087 = LINE ( 'NONE', #47074, #81734 ) ; +#22089 = CARTESIAN_POINT ( 'NONE', ( 1.689681756505250210, -0.9624218420162741205, 0.8299999999999999600 ) ) ; +#22090 = PRESENTATION_STYLE_ASSIGNMENT (( #21585 ) ) ; +#22091 = LINE ( 'NONE', #90285, #52901 ) ; +#22092 = VECTOR ( 'NONE', #71100, 1000.000000000000000 ) ; +#22093 = EDGE_LOOP ( 'NONE', ( #21707, #12947, #41127, #7353, #14034, #68238, #14208, #99781, #66397, #9951, #10343, #43478, #99416, #18273, #48233, #64224, #56609, #21260, #88734 ) ) ; +#22094 = SURFACE_SIDE_STYLE ('',( #35944 ) ) ; +#22095 = FILL_AREA_STYLE ('',( #59449 ) ) ; +#22096 = SURFACE_SIDE_STYLE ('',( #29745 ) ) ; +#22099 = VECTOR ( 'NONE', #64411, 1000.000000000000000 ) ; +#22098 = VECTOR ( 'NONE', #62899, 1000.000000000000000 ) ; +#22097 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#22100 = PLANE ( 'NONE', #83561 ) ; +#22101 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66139 ) ) ; +#22102 = LINE ( 'NONE', #21597, #14287 ) ; +#22103 = PLANE ( 'NONE', #14307 ) ; +#22104 = CARTESIAN_POINT ( 'NONE', ( -0.03878568267182790075, 1.364454123474860170, 0.8100000000000000533 ) ) ; +#22105 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000089, 0.000000000000000000 ) ) ; +#22106 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -2.143355994988570127E-63 ) ) ; +#22107 = VECTOR ( 'NONE', #42921, 1000.000000000000000 ) ; +#22108 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25032 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36192, #42832, #11592 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22109 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#22110 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#22111 = EDGE_LOOP ( 'NONE', ( #97981, #3228, #9161, #32495 ) ) ; +#22112 = FILL_AREA_STYLE ('',( #7209 ) ) ; +#22113 = ADVANCED_FACE ( 'NONE', ( #92414 ), #46971, .T. ) ; +#22114 = EDGE_LOOP ( 'NONE', ( #88978, #14177, #68054 ) ) ; +#22115 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56033 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13823, #15356, #62898 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22117 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22118 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22119 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22120 = SURFACE_STYLE_FILL_AREA ( #14411 ) ; +#22121 = CARTESIAN_POINT ( 'NONE', ( 1.812952947087890232, -0.9302426320460149833, 0.8299999999999999600 ) ) ; +#22122 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.9000000000000014655, 0.000000000000000000 ) ) ; +#22123 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#22124 = ORIENTED_EDGE ( 'NONE', *, *, #14578, .T. ) ; +#22125 = FILL_AREA_STYLE ('',( #23147 ) ) ; +#22126 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000013115, 0.2400000000000000189 ) ) ; +#22127 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#22128 = ORIENTED_EDGE ( 'NONE', *, *, #74276, .T. ) ; +#22129 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22130 = LINE ( 'NONE', #7236, #56684 ) ; +#22131 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22132 = CARTESIAN_POINT ( 'NONE', ( -1.263508545851719900, -1.411115659170130154, 0.8100000000000010525 ) ) ; +#22133 = ADVANCED_FACE ( 'NONE', ( #1543 ), #69941, .T. ) ; +#22134 = DIRECTION ( 'NONE', ( 0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#22135 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22136 = ORIENTED_EDGE ( 'NONE', *, *, #81501, .F. ) ; +#22137 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#22138 = LINE ( 'NONE', #13925, #53916 ) ; +#22139 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22140 = VECTOR ( 'NONE', #16641, 1000.000000000000000 ) ; +#22141 = AXIS2_PLACEMENT_3D ( 'NONE', #66428, #11207, #57810 ) ; +#22142 = CARTESIAN_POINT ( 'NONE', ( 1.680683372326140068, -0.9625852181168449428, 0.8099999999999994982 ) ) ; +#22144 = ADVANCED_FACE ( 'NONE', ( #47478 ), #46446, .T. ) ; +#22143 = VECTOR ( 'NONE', #57361, 1000.000000000000000 ) ; +#22145 = ORIENTED_EDGE ( 'NONE', *, *, #22288, .T. ) ; +#22146 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22147 = LINE ( 'NONE', #76265, #92937 ) ; +#22148 = LINE ( 'NONE', #36989, #2160 ) ; +#22149 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#22150 = SURFACE_SIDE_STYLE ('',( #73907 ) ) ; +#22151 = VECTOR ( 'NONE', #27317, 1000.000000000000000 ) ; +#22152 = EDGE_LOOP ( 'NONE', ( #86704, #96594, #72365, #10535 ) ) ; +#22153 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22154 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100942 ) ; +#22155 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41691, 'distance_accuracy_value', 'NONE'); +#22156 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69428 ), #20553 ) ; +#22157 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22158 = EDGE_CURVE ( 'NONE', #13016, #30563, #5657, .T. ) ; +#22159 = ORIENTED_EDGE ( 'NONE', *, *, #33521, .F. ) ; +#22161 = ORIENTED_EDGE ( 'NONE', *, *, #69299, .F. ) ; +#22160 = DIRECTION ( 'NONE', ( 0.7071067816865476141, -0.7071067806865475314, 0.000000000000000000 ) ) ; +#22163 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22162 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45251, 'distance_accuracy_value', 'NONE'); +#22165 = CARTESIAN_POINT ( 'NONE', ( -1.171237681315639989, -1.515071875619850017, 0.8100000000000000533 ) ) ; +#22164 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22166 = LINE ( 'NONE', #37003, #13739 ) ; +#22167 = CARTESIAN_POINT ( 'NONE', ( 10.25691949950005011, 3.831700500499952255, 0.8991599999999999593 ) ) ; +#22168 = ORIENTED_EDGE ( 'NONE', *, *, #93547, .F. ) ; +#22169 = EDGE_CURVE ( 'NONE', #2574, #97792, #10596, .T. ) ; +#22170 = ORIENTED_EDGE ( 'NONE', *, *, #19679, .F. ) ; +#22171 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8100000000000000533 ) ) ; +#22172 = STYLED_ITEM ( 'NONE', ( #22427 ), #39102 ) ; +#22173 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72552, #26120, #33776, #57268 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22174 = PRESENTATION_STYLE_ASSIGNMENT (( #85970 ) ) ; +#22175 = ORIENTED_EDGE ( 'NONE', *, *, #74326, .F. ) ; +#22176 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01499999999999999944, 0.1400000000000000133 ) ) ; +#22177 = ORIENTED_EDGE ( 'NONE', *, *, #51126, .F. ) ; +#22178 = VECTOR ( 'NONE', #31042, 1000.000000000000000 ) ; +#22179 = EDGE_CURVE ( 'NONE', #51226, #79783, #75441, .T. ) ; +#22180 = ADVANCED_FACE ( 'NONE', ( #9604 ), #18844, .T. ) ; +#22181 = CIRCLE ( 'NONE', #74383, 0.6500000000642103259 ) ; +#22183 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999990674, 3.123820061220075051, 0.000000000000000000 ) ) ; +#22182 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#22184 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, -0.000000000000000000 ) ) ; +#22185 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22186 = EDGE_CURVE ( 'NONE', #50031, #96362, #95428, .T. ) ; +#22187 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#22188 = EDGE_CURVE ( 'NONE', #91124, #89235, #46294, .T. ) ; +#22189 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36859 ) ) ; +#22190 = EDGE_LOOP ( 'NONE', ( #50588, #54821, #56446, #34872 ) ) ; +#22191 = FILL_AREA_STYLE_COLOUR ( '', #90662 ) ; +#22192 = ORIENTED_EDGE ( 'NONE', *, *, #30544, .T. ) ; +#22194 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#22193 = FILL_AREA_STYLE ('',( #76305 ) ) ; +#22195 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#22196 = EDGE_CURVE ( 'NONE', #51353, #65218, #4040, .T. ) ; +#22197 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22198 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22199 = VECTOR ( 'NONE', #23096, 1000.000000000000000 ) ; +#22200 = CARTESIAN_POINT ( 'NONE', ( 1.387778780781510079E-17, 0.2799999999751889845, -2.099015404554671279E-18 ) ) ; +#22201 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22202 = FILL_AREA_STYLE ('',( #52368 ) ) ; +#22203 = EDGE_CURVE ( 'NONE', #58022, #57512, #35220, .T. ) ; +#22204 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22205 = PRESENTATION_STYLE_ASSIGNMENT (( #84484 ) ) ; +#22206 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#22207 = ORIENTED_EDGE ( 'NONE', *, *, #66296, .T. ) ; +#22209 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13235 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7920, #92735, #24882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22208 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.869314090631718434E-16, 0.000000000000000000 ) ) ; +#22210 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #29861 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #31452 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#22212 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22211 = CYLINDRICAL_SURFACE ( 'NONE', #49003, 0.1200000000000000927 ) ; +#22213 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5463, 'distance_accuracy_value', 'NONE'); +#22214 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#22215 = PLANE ( 'NONE', #93496 ) ; +#22216 = VECTOR ( 'NONE', #86655, 1000.000000000000000 ) ; +#22217 = CIRCLE ( 'NONE', #48347, 0.2000000000000000944 ) ; +#22218 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#22219 = ORIENTED_EDGE ( 'NONE', *, *, #79337, .T. ) ; +#22220 = STYLED_ITEM ( 'NONE', ( #37426 ), #61505 ) ; +#22221 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#22222 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#22223 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22224 = CARTESIAN_POINT ( 'NONE', ( 0.005236623695644900336, -1.379727385542079965, 0.8100000000000000533 ) ) ; +#22225 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22226 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20546 ), #59751 ) ; +#22228 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54833 ), #10701 ) ; +#22227 = SURFACE_SIDE_STYLE ('',( #12475 ) ) ; +#22229 = FILL_AREA_STYLE ('',( #53377 ) ) ; +#22230 = SURFACE_STYLE_FILL_AREA ( #14522 ) ; +#22231 = FILL_AREA_STYLE ('',( #92638 ) ) ; +#22232 = PLANE ( 'NONE', #50840 ) ; +#22233 = PLANE ( 'NONE', #27888 ) ; +#22235 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#22234 = STYLED_ITEM ( 'NONE', ( #34520 ), #78067 ) ; +#22236 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22237 = PLANE ( 'NONE', #61877 ) ; +#22238 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22239 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22240 = EDGE_CURVE ( 'NONE', #5298, #92463, #90304, .T. ) ; +#22241 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22242 = PRESENTATION_STYLE_ASSIGNMENT (( #99260 ) ) ; +#22243 = PRESENTATION_STYLE_ASSIGNMENT (( #92172 ) ) ; +#22244 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22245 = SURFACE_SIDE_STYLE ('',( #53393 ) ) ; +#22246 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, -0.1400000000000000133 ) ) ; +#22247 = ORIENTED_EDGE ( 'NONE', *, *, #63504, .T. ) ; +#22248 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4849999999999999867, -0.2500000000000000000 ) ) ; +#22249 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28726 ), #54854 ) ; +#22250 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36907 ), #25561 ) ; +#22251 = LINE ( 'NONE', #29899, #2142 ) ; +#22252 = LINE ( 'NONE', #53904, #100747 ) ; +#22253 = ORIENTED_EDGE ( 'NONE', *, *, #71697, .F. ) ; +#22254 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, -3.500000000000000444, 0.000000000000000000 ) ) ; +#22255 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89177 ), #85880 ) ; +#22256 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1050 ), #84217 ) ; +#22257 = FILL_AREA_STYLE ('',( #43719 ) ) ; +#22258 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8100000000000074918 ) ) ; +#22259 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22260 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22261 = STYLED_ITEM ( 'NONE', ( #70266 ), #4057 ) ; +#22262 = VERTEX_POINT ( 'NONE', #28530 ) ; +#22263 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22264 = VECTOR ( 'NONE', #42146, 1000.000000000000000 ) ; +#22265 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77693, 'distance_accuracy_value', 'NONE'); +#22266 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#22267 = FILL_AREA_STYLE_COLOUR ( '', #84368 ) ; +#22268 = ADVANCED_FACE ( 'NONE', ( #51039 ), #52525, .F. ) ; +#22269 = ORIENTED_EDGE ( 'NONE', *, *, #46150, .T. ) ; +#22270 = ORIENTED_EDGE ( 'NONE', *, *, #23224, .F. ) ; +#22271 = LINE ( 'NONE', #47776, #86663 ) ; +#22272 = EDGE_LOOP ( 'NONE', ( #42398, #54083, #94535, #49605 ) ) ; +#22273 = CARTESIAN_POINT ( 'NONE', ( -0.05183531411288819918, -1.501723168847330259, 0.8299999999999999600 ) ) ; +#22274 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8299999999999999600 ) ) ; +#22275 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22276 = PRESENTATION_STYLE_ASSIGNMENT (( #92209 ) ) ; +#22277 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1019 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12213, #42933, #33792 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22278 = VERTEX_POINT ( 'NONE', #67807 ) ; +#22279 = ORIENTED_EDGE ( 'NONE', *, *, #76486, .F. ) ; +#22280 = CARTESIAN_POINT ( 'NONE', ( 1.854016048130769923, -1.137681993439920047, 0.8299999999999995159 ) ) ; +#22281 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39207 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88052, #62577, #49251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22282 = AXIS2_PLACEMENT_3D ( 'NONE', #21342, #27526, #73973 ) ; +#22283 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53524, 'distance_accuracy_value', 'NONE'); +#22284 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22286 = CARTESIAN_POINT ( 'NONE', ( 1.205401789321949968, -0.8845642871695170717, 0.8100000000000000533 ) ) ; +#22285 = LINE ( 'NONE', #76917, #1958 ) ; +#22287 = SURFACE_STYLE_FILL_AREA ( #46753 ) ; +#22288 = EDGE_CURVE ( 'NONE', #47242, #87120, #53031, .T. ) ; +#22289 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66332 ), #28776 ) ; +#22290 = VECTOR ( 'NONE', #34652, 1000.000000000000000 ) ; +#22291 = VERTEX_POINT ( 'NONE', #99383 ) ; +#22293 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22292 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22294 = VERTEX_POINT ( 'NONE', #45320 ) ; +#22295 = ORIENTED_EDGE ( 'NONE', *, *, #87436, .T. ) ; +#22297 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -2.299999999999999378, 0.8299999999999999600 ) ) ; +#22296 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22298 = CYLINDRICAL_SURFACE ( 'NONE', #26161, 0.009999999999999998473 ) ; +#22299 = FILL_AREA_STYLE ('',( #21799 ) ) ; +#22301 = ORIENTED_EDGE ( 'NONE', *, *, #79095, .T. ) ; +#22300 = FILL_AREA_STYLE ('',( #68742 ) ) ; +#22302 = SURFACE_SIDE_STYLE ('',( #84588 ) ) ; +#22303 = EDGE_CURVE ( 'NONE', #27601, #7273, #74158, .T. ) ; +#22304 = LINE ( 'NONE', #59665, #51929 ) ; +#22305 = AXIS2_PLACEMENT_3D ( 'NONE', #32037, #77993, #7452 ) ; +#22306 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22307 = ORIENTED_EDGE ( 'NONE', *, *, #63734, .T. ) ; +#22308 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.000000000000000000 ) ) ; +#22309 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#22310 = ORIENTED_EDGE ( 'NONE', *, *, #34120, .T. ) ; +#22311 = ORIENTED_EDGE ( 'NONE', *, *, #66427, .F. ) ; +#22312 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8100000000000000533 ) ) ; +#22313 = FILL_AREA_STYLE ('',( #61659 ) ) ; +#22314 = AXIS2_PLACEMENT_3D ( 'NONE', #29977, #46288, #5953 ) ; +#22315 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#22316 = STYLED_ITEM ( 'NONE', ( #64582 ), #99902 ) ; +#22317 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22318 = FILL_AREA_STYLE_COLOUR ( '', #65795 ) ; +#22319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22320 = EDGE_CURVE ( 'NONE', #66295, #21432, #20867, .T. ) ; +#22321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72857 ), #23969 ) ; +#22322 = ORIENTED_EDGE ( 'NONE', *, *, #79642, .F. ) ; +#22323 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#22324 = VERTEX_POINT ( 'NONE', #29533 ) ; +#22325 = LINE ( 'NONE', #30994, #79978 ) ; +#22326 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#22327 = SURFACE_STYLE_FILL_AREA ( #84121 ) ; +#22329 = AXIS2_PLACEMENT_3D ( 'NONE', #29687, #84813, #83835 ) ; +#22328 = SURFACE_STYLE_FILL_AREA ( #45779 ) ; +#22330 = SURFACE_STYLE_USAGE ( .BOTH. , #69248 ) ; +#22331 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#22332 = LINE ( 'NONE', #100324, #30549 ) ; +#22333 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -0.7000000000000009548, 1.747825839084689943E-76 ) ) ; +#22334 = ORIENTED_EDGE ( 'NONE', *, *, #9440, .T. ) ; +#22335 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22336 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#22337 = FILL_AREA_STYLE ('',( #61184 ) ) ; +#22338 = LINE ( 'NONE', #70310, #55616 ) ; +#22339 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22340 = CIRCLE ( 'NONE', #87505, 0.1000000000000000056 ) ; +#22341 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22342 = FILL_AREA_STYLE_COLOUR ( '', #42340 ) ; +#22343 = EDGE_CURVE ( 'NONE', #78277, #98340, #83671, .T. ) ; +#22344 = PLANE ( 'NONE', #30985 ) ; +#22345 = AXIS2_PLACEMENT_3D ( 'NONE', #35685, #11584, #64785 ) ; +#22346 = FILL_AREA_STYLE_COLOUR ( '', #46710 ) ; +#22347 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22348 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 1.458578643762689975, 0.000000000000000000 ) ) ; +#22349 = FILL_AREA_STYLE_COLOUR ( '', #40408 ) ; +#22350 = CARTESIAN_POINT ( 'NONE', ( 1.263543985521710100, -0.9656714926165439472, 0.8299999999999995159 ) ) ; +#22351 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22352 = VECTOR ( 'NONE', #81033, 1000.000000000000000 ) ; +#22353 = LINE ( 'NONE', #372, #10958 ) ; +#22355 = EDGE_CURVE ( 'NONE', #12048, #56475, #76489, .T. ) ; +#22354 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22356 = CARTESIAN_POINT ( 'NONE', ( -1.247072273956122856, -1.421558282304847154, 0.8099999999996772004 ) ) ; +#22357 = ORIENTED_EDGE ( 'NONE', *, *, #48396, .F. ) ; +#22358 = AXIS2_PLACEMENT_3D ( 'NONE', #93639, #30886, #39565 ) ; +#22359 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#22360 = FILL_AREA_STYLE ('',( #54021 ) ) ; +#22361 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#22363 = PLANE ( 'NONE', #70372 ) ; +#22362 = VECTOR ( 'NONE', #51731, 1000.000000000000000 ) ; +#22364 = PRESENTATION_STYLE_ASSIGNMENT (( #16188 ) ) ; +#22365 = FACE_OUTER_BOUND ( 'NONE', #55896, .T. ) ; +#22366 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35789, #4594, #60279, #90887 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22367 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69649 ) ) ; +#22368 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#22369 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12802, #75177, #29686, #67968 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22371 = ORIENTED_EDGE ( 'NONE', *, *, #75410, .F. ) ; +#22370 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82739 ), #89302 ) ; +#22372 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22373 = SURFACE_STYLE_USAGE ( .BOTH. , #14167 ) ; +#22374 = SURFACE_STYLE_FILL_AREA ( #91806 ) ; +#22375 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14680 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100612, #653, #85423 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22376 = SURFACE_STYLE_FILL_AREA ( #46854 ) ; +#22377 = CLOSED_SHELL ( 'NONE', ( #86185, #19087, #36808, #46067, #46180, #60605 ) ) ; +#22378 = EDGE_CURVE ( 'NONE', #78320, #88079, #38915, .T. ) ; +#22380 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51790 ) ) ; +#22379 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22381 = ORIENTED_EDGE ( 'NONE', *, *, #38311, .F. ) ; +#22382 = ORIENTED_EDGE ( 'NONE', *, *, #75507, .T. ) ; +#22383 = VECTOR ( 'NONE', #69439, 1000.000000000000000 ) ; +#22384 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22385 = EDGE_LOOP ( 'NONE', ( #12572, #54427, #90899, #62498 ) ) ; +#22386 = CARTESIAN_POINT ( 'NONE', ( -0.3116609922593340243, -1.321596304865350069, 0.8299999999999999600 ) ) ; +#22387 = LINE ( 'NONE', #92329, #98636 ) ; +#22388 = EDGE_CURVE ( 'NONE', #65875, #61508, #21363, .T. ) ; +#22389 = FACE_OUTER_BOUND ( 'NONE', #82997, .T. ) ; +#22390 = LINE ( 'NONE', #62233, #66263 ) ; +#22391 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#22392 = VECTOR ( 'NONE', #96499, 1000.000000000000000 ) ; +#22393 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22394 = PRODUCT_CONTEXT ( 'NONE', #93145, 'mechanical' ) ; +#22395 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22397 = ORIENTED_EDGE ( 'NONE', *, *, #89084, .T. ) ; +#22396 = ORIENTED_EDGE ( 'NONE', *, *, #37736, .T. ) ; +#22398 = ORIENTED_EDGE ( 'NONE', *, *, #76475, .T. ) ; +#22399 = LINE ( 'NONE', #75527, #63813 ) ; +#22400 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #124, 'distance_accuracy_value', 'NONE'); +#22402 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 12.65647100000000158, 0.8648700000000000276 ) ) ; +#22401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22403 = EDGE_LOOP ( 'NONE', ( #16442, #73406, #49309, #22136 ) ) ; +#22404 = EDGE_CURVE ( 'NONE', #20765, #80337, #37220, .T. ) ; +#22405 = EDGE_LOOP ( 'NONE', ( #27196, #22554, #57788, #31432 ) ) ; +#22406 = ADVANCED_FACE ( 'NONE', ( #100354 ), #100845, .T. ) ; +#22407 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#22408 = PRESENTATION_STYLE_ASSIGNMENT (( #15204 ) ) ; +#22409 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.9000000000000014655, 8.225148568024281774E-79 ) ) ; +#22410 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29019 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84058, #86957, #16450 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22412 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#22411 = PLANE ( 'NONE', #35168 ) ; +#22413 = CARTESIAN_POINT ( 'NONE', ( -0.3774237423761729882, -1.003781515188449935, 0.8299999999999999600 ) ) ; +#22415 = VERTEX_POINT ( 'NONE', #61705 ) ; +#22414 = AXIS2_PLACEMENT_3D ( 'NONE', #38045, #52376, #75835 ) ; +#22416 = CARTESIAN_POINT ( 'NONE', ( -0.5594783971358769925, -0.9704561130045840089, 0.8100000000000000533 ) ) ; +#22417 = VERTEX_POINT ( 'NONE', #23913 ) ; +#22418 = ORIENTED_EDGE ( 'NONE', *, *, #38140, .F. ) ; +#22419 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.000000000000000000, -12.01999999999999957 ) ) ; +#22420 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22422 = ORIENTED_EDGE ( 'NONE', *, *, #29081, .F. ) ; +#22421 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22423 = PLANE ( 'NONE', #9028 ) ; +#22424 = EDGE_CURVE ( 'NONE', #58838, #93833, #54550, .T. ) ; +#22425 = VECTOR ( 'NONE', #30003, 1000.000000000000000 ) ; +#22426 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40389 ) ) ; +#22427 = PRESENTATION_STYLE_ASSIGNMENT (( #99923 ) ) ; +#22428 = VERTEX_POINT ( 'NONE', #384 ) ; +#22429 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#22430 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8299999999999999600 ) ) ; +#22431 = ORIENTED_EDGE ( 'NONE', *, *, #82146, .F. ) ; +#22432 = VERTEX_POINT ( 'NONE', #85665 ) ; +#22433 = CARTESIAN_POINT ( 'NONE', ( -0.1381505133853425660, 2.561284075926966608, 0.8100000000000000533 ) ) ; +#22434 = VECTOR ( 'NONE', #41595, 1000.000000000000000 ) ; +#22435 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22436 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69723 ), #95732 ) ; +#22437 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22438 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#22439 = CARTESIAN_POINT ( 'NONE', ( 1.028534346447049996, -1.164020980542209927, 0.8299999999999997380 ) ) ; +#22440 = EDGE_CURVE ( 'NONE', #37187, #63310, #39706, .T. ) ; +#22441 = DIRECTION ( 'NONE', ( -0.7071067811865464625, 0.7071067811865486830, 0.000000000000000000 ) ) ; +#22442 = CARTESIAN_POINT ( 'NONE', ( 0.1751932085031089881, -1.046109390704299980, 0.8300000000000020695 ) ) ; +#22443 = ORIENTED_EDGE ( 'NONE', *, *, #49009, .T. ) ; +#22444 = SURFACE_STYLE_USAGE ( .BOTH. , #76563 ) ; +#22445 = STYLED_ITEM ( 'NONE', ( #93518 ), #24439 ) ; +#22446 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#22447 = ORIENTED_EDGE ( 'NONE', *, *, #29604, .F. ) ; +#22448 = SURFACE_SIDE_STYLE ('',( #9069 ) ) ; +#22449 = FACE_OUTER_BOUND ( 'NONE', #12538, .T. ) ; +#22450 = VECTOR ( 'NONE', #78260, 1000.000000000000000 ) ; +#22451 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, 0.000000000000000000 ) ) ; +#22452 = SURFACE_STYLE_USAGE ( .BOTH. , #23475 ) ; +#22453 = AXIS2_PLACEMENT_3D ( 'NONE', #94321, #38217, #61719 ) ; +#22455 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#22454 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22456 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22457 = CLOSED_SHELL ( 'NONE', ( #45789, #53197, #17094, #21386, #30028, #2466 ) ) ; +#22458 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22459 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#22460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22461 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77923 ) ) ; +#22462 = VECTOR ( 'NONE', #80179, 1000.000000000000114 ) ; +#22463 = SURFACE_STYLE_USAGE ( .BOTH. , #67896 ) ; +#22464 = SURFACE_SIDE_STYLE ('',( #98485 ) ) ; +#22465 = FACE_OUTER_BOUND ( 'NONE', #30132, .T. ) ; +#22466 = PLANE ( 'NONE', #66144 ) ; +#22467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97443 ), #45319 ) ; +#22468 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#22469 = AXIS2_PLACEMENT_3D ( 'NONE', #53963, #62157, #15104 ) ; +#22470 = ADVANCED_FACE ( 'NONE', ( #14668 ), #86157, .T. ) ; +#22471 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#22472 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81184 ) ) ; +#22473 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#22474 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22475 = VERTEX_POINT ( 'NONE', #37706 ) ; +#22476 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22477 = EDGE_CURVE ( 'NONE', #15440, #94369, #92306, .T. ) ; +#22478 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19840, 'distance_accuracy_value', 'NONE'); +#22479 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15115, 'distance_accuracy_value', 'NONE'); +#22480 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22481 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.300000000000000044, -0.02000000000000000042 ) ) ; +#22482 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.449999999999999956, -11.41999999999999993 ) ) ; +#22484 = FILL_AREA_STYLE_COLOUR ( '', #40125 ) ; +#22483 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2909 ), #35575 ) ; +#22485 = STYLED_ITEM ( 'NONE', ( #9830 ), #74408 ) ; +#22486 = ORIENTED_EDGE ( 'NONE', *, *, #62125, .F. ) ; +#22487 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22488 = VERTEX_POINT ( 'NONE', #54024 ) ; +#22489 = FACE_OUTER_BOUND ( 'NONE', #17032, .T. ) ; +#22490 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13911, 'distance_accuracy_value', 'NONE'); +#22491 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29879, 'distance_accuracy_value', 'NONE'); +#22492 = CYLINDRICAL_SURFACE ( 'NONE', #72737, 0.09999999999999939493 ) ; +#22493 = LINE ( 'NONE', #30633, #60850 ) ; +#22494 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86169 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63604, #56961, #9860 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20743 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58825, #88928, #73106 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22496 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22497 = SURFACE_SIDE_STYLE ('',( #62338 ) ) ; +#22498 = CARTESIAN_POINT ( 'NONE', ( -0.2766204946046708080, -0.9850623610146642672, 0.8100000000002682832 ) ) ; +#22499 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22500 = EDGE_LOOP ( 'NONE', ( #43366, #55456, #34394, #342 ) ) ; +#22501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22502 = SURFACE_STYLE_FILL_AREA ( #15827 ) ; +#22503 = ORIENTED_EDGE ( 'NONE', *, *, #53237, .F. ) ; +#22504 = PLANE ( 'NONE', #68588 ) ; +#22505 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#22506 = VECTOR ( 'NONE', #23215, 1000.000000000000114 ) ; +#22507 = VERTEX_POINT ( 'NONE', #15165 ) ; +#22508 = EDGE_CURVE ( 'NONE', #78634, #37995, #70547, .T. ) ; +#22509 = EDGE_CURVE ( 'NONE', #41413, #16845, #88830, .T. ) ; +#22510 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#22511 = VECTOR ( 'NONE', #46128, 1000.000000000000000 ) ; +#22512 = FACE_OUTER_BOUND ( 'NONE', #9542, .T. ) ; +#22513 = CARTESIAN_POINT ( 'NONE', ( 3.594100000000000072, 10.63498000000000054, 0.8991599999999999593 ) ) ; +#22514 = SURFACE_STYLE_FILL_AREA ( #61365 ) ; +#22515 = CARTESIAN_POINT ( 'NONE', ( 0.1469259719417066734, 0.8140837401805022244, 0.8100000000000001643 ) ) ; +#22516 = STYLED_ITEM ( 'NONE', ( #26909 ), #62795 ) ; +#22518 = VERTEX_POINT ( 'NONE', #43102 ) ; +#22517 = ORIENTED_EDGE ( 'NONE', *, *, #83100, .T. ) ; +#22519 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22520 = SURFACE_STYLE_USAGE ( .BOTH. , #99533 ) ; +#22522 = VECTOR ( 'NONE', #35347, 1000.000000000000000 ) ; +#22521 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#22523 = VERTEX_POINT ( 'NONE', #72351 ) ; +#22524 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22525 = AXIS2_PLACEMENT_3D ( 'NONE', #81582, #95832, #25942 ) ; +#22527 = CARTESIAN_POINT ( 'NONE', ( -0.4517812530547630212, -1.032254439803430124, 0.8100000000000000533 ) ) ; +#22526 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#22528 = CLOSED_SHELL ( 'NONE', ( #60946, #57691, #15725, #24495, #76904, #49121 ) ) ; +#22529 = ORIENTED_EDGE ( 'NONE', *, *, #59902, .F. ) ; +#22530 = EDGE_CURVE ( 'NONE', #9357, #7176, #98159, .T. ) ; +#22531 = ORIENTED_EDGE ( 'NONE', *, *, #34757, .T. ) ; +#22532 = EDGE_CURVE ( 'NONE', #78606, #66411, #1922, .T. ) ; +#22533 = PLANE ( 'NONE', #61266 ) ; +#22534 = SURFACE_STYLE_FILL_AREA ( #15338 ) ; +#22535 = CARTESIAN_POINT ( 'NONE', ( -0.4757099785863510011, -1.161113228842870049, 0.8299999999999999600 ) ) ; +#22536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22538 = FILL_AREA_STYLE ('',( #14828 ) ) ; +#22537 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22539 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22541 = EDGE_LOOP ( 'NONE', ( #83612, #29472, #9538, #84670, #13625, #46496 ) ) ; +#22540 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24674 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54109, #7548, #62287 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22542 = ADVANCED_FACE ( 'NONE', ( #90065 ), #51287, .F. ) ; +#22543 = ORIENTED_EDGE ( 'NONE', *, *, #58902, .F. ) ; +#22544 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22545 = ORIENTED_EDGE ( 'NONE', *, *, #43229, .F. ) ; +#22546 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#22547 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78956, #38643, #34541 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22550 = ORIENTED_EDGE ( 'NONE', *, *, #67934, .F. ) ; +#22549 = AXIS2_PLACEMENT_3D ( 'NONE', #30760, #76738, #45063 ) ; +#22548 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#22551 = EDGE_CURVE ( 'NONE', #62618, #76431, #56060, .T. ) ; +#22552 = PLANE ( 'NONE', #55579 ) ; +#22553 = PLANE ( 'NONE', #79881 ) ; +#22554 = ORIENTED_EDGE ( 'NONE', *, *, #28742, .F. ) ; +#22555 = DIRECTION ( 'NONE', ( -0.000000000000000000, -4.266452400824600274E-34, -1.000000000000000000 ) ) ; +#22556 = LINE ( 'NONE', #100536, #42716 ) ; +#22557 = ORIENTED_EDGE ( 'NONE', *, *, #70860, .T. ) ; +#22558 = ADVANCED_FACE ( 'NONE', ( #9978 ), #20108, .T. ) ; +#22559 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#22560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9487 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57738, #12669, #98914 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22561 = ORIENTED_EDGE ( 'NONE', *, *, #15814, .F. ) ; +#22562 = FILL_AREA_STYLE ('',( #31735 ) ) ; +#22563 = EDGE_CURVE ( 'NONE', #95765, #68360, #51788, .T. ) ; +#22565 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#22564 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#22566 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66592 ) ) ; +#22567 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.499999999999960032, -0.02000000000000000042 ) ) ; +#22569 = EDGE_CURVE ( 'NONE', #81709, #3989, #4787, .T. ) ; +#22568 = CARTESIAN_POINT ( 'NONE', ( 2.276179938779915091, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#22570 = LINE ( 'NONE', #42187, #11854 ) ; +#22571 = VERTEX_POINT ( 'NONE', #87184 ) ; +#22572 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#22573 = VECTOR ( 'NONE', #2689, 1000.000000000000000 ) ; +#22574 = EDGE_CURVE ( 'NONE', #90078, #66856, #63726, .T. ) ; +#22575 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22576 = SURFACE_STYLE_FILL_AREA ( #589 ) ; +#22578 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#22577 = CARTESIAN_POINT ( 'NONE', ( 0.4264791961179740243, -0.9850687526833949992, 0.8299999999999999600 ) ) ; +#22579 = CARTESIAN_POINT ( 'NONE', ( 7.895183000000000284, 10.29465700000000083, 0.8991599999999999593 ) ) ; +#22580 = FILL_AREA_STYLE ('',( #100072 ) ) ; +#22581 = PRODUCT_DEFINITION ( 'δ֪', '', #24196, #41231 ) ; +#22582 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22583 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.01499999999999999944, -0.2400000000000000189 ) ) ; +#22584 = FILL_AREA_STYLE ('',( #30222 ) ) ; +#22585 = STYLED_ITEM ( 'NONE', ( #16903 ), #79845 ) ; +#22586 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#22587 = ORIENTED_EDGE ( 'NONE', *, *, #42358, .F. ) ; +#22588 = SURFACE_STYLE_USAGE ( .BOTH. , #6196 ) ; +#22589 = VECTOR ( 'NONE', #17780, 1000.000000000000000 ) ; +#22590 = EDGE_LOOP ( 'NONE', ( #58621, #88722, #79762, #89509 ) ) ; +#22591 = EDGE_CURVE ( 'NONE', #42382, #85300, #48414, .T. ) ; +#22592 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9971, #31657, #92412 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22593 = STYLED_ITEM ( 'NONE', ( #56943 ), #63298 ) ; +#22595 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#22594 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22596 = VECTOR ( 'NONE', #57034, 1000.000000000000000 ) ; +#22597 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#22598 = SURFACE_STYLE_USAGE ( .BOTH. , #84866 ) ; +#22599 = STYLED_ITEM ( 'NONE', ( #13312 ), #166 ) ; +#22600 = VERTEX_POINT ( 'NONE', #60957 ) ; +#22601 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#22602 = ADVANCED_FACE ( 'NONE', ( #21129 ), #61962, .T. ) ; +#22603 = SURFACE_STYLE_USAGE ( .BOTH. , #24144 ) ; +#22604 = PRESENTATION_STYLE_ASSIGNMENT (( #99607 ) ) ; +#22605 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22606 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53141, #84276, #52152, #44927 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22607 = CARTESIAN_POINT ( 'NONE', ( 0.9629666814316270029, -1.351356007592229957, 0.8300000000000010703 ) ) ; +#22608 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8299999999999999600 ) ) ; +#22609 = LINE ( 'NONE', #94012, #54052 ) ; +#22610 = VECTOR ( 'NONE', #23874, 1000.000000000000000 ) ; +#22611 = ADVANCED_FACE ( 'NONE', ( #92547 ), #84906, .T. ) ; +#22612 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#22613 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#22614 = FILL_AREA_STYLE ('',( #5744 ) ) ; +#22615 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22616 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69174, 'distance_accuracy_value', 'NONE'); +#22617 = STYLED_ITEM ( 'NONE', ( #65699 ), #15136 ) ; +#22618 = PRESENTATION_STYLE_ASSIGNMENT (( #84884 ) ) ; +#22619 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22620 = ORIENTED_EDGE ( 'NONE', *, *, #73346, .T. ) ; +#22621 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.100000000000000089, 0.1829999999999959992 ) ) ; +#22622 = ADVANCED_FACE ( 'NONE', ( #91074 ), #14418, .T. ) ; +#22623 = ORIENTED_EDGE ( 'NONE', *, *, #18696, .T. ) ; +#22624 = DIRECTION ( 'NONE', ( -8.347776819438500435E-49, -0.000000000000000000, 1.000000000000000000 ) ) ; +#22625 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57778, 'distance_accuracy_value', 'NONE'); +#22626 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58812, 'distance_accuracy_value', 'NONE'); +#22627 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45395 ) ) ; +#22628 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22629 = SURFACE_STYLE_FILL_AREA ( #83419 ) ; +#22630 = SURFACE_SIDE_STYLE ('',( #58471 ) ) ; +#22631 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22632 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22633 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22634 = EDGE_LOOP ( 'NONE', ( #8041, #69595, #43833, #95421 ) ) ; +#22635 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#22636 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22637 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55987, 'distance_accuracy_value', 'NONE'); +#22638 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#22639 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76409 ), #89484 ) ; +#22640 = AXIS2_PLACEMENT_3D ( 'NONE', #69870, #62253, #15736 ) ; +#22641 = VERTEX_POINT ( 'NONE', #643 ) ; +#22642 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22643 = EDGE_CURVE ( 'NONE', #95866, #28792, #99567, .T. ) ; +#22644 = EDGE_CURVE ( 'NONE', #35165, #84202, #16440, .T. ) ; +#22645 = LINE ( 'NONE', #69055, #5929 ) ; +#22646 = SURFACE_STYLE_USAGE ( .BOTH. , #37969 ) ; +#22647 = STYLED_ITEM ( 'NONE', ( #5024 ), #92546 ) ; +#22648 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22649 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999992895, -3.149999999999990585, 0.000000000000000000 ) ) ; +#22650 = FACE_OUTER_BOUND ( 'NONE', #96377, .T. ) ; +#22651 = FACE_OUTER_BOUND ( 'NONE', #70907, .T. ) ; +#22652 = ORIENTED_EDGE ( 'NONE', *, *, #67700, .F. ) ; +#22653 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48818 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78542, #34007, #69867 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22654 = PLANE ( 'NONE', #44064 ) ; +#22655 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80146, 'distance_accuracy_value', 'NONE'); +#22657 = PRESENTATION_STYLE_ASSIGNMENT (( #9258 ) ) ; +#22656 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3128 ), #83006 ) ; +#22658 = FACE_OUTER_BOUND ( 'NONE', #55725, .T. ) ; +#22659 = ORIENTED_EDGE ( 'NONE', *, *, #8661, .F. ) ; +#22660 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22661 = EDGE_CURVE ( 'NONE', #7959, #10911, #17465, .T. ) ; +#22662 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.699999999999999956, 0.1829999999999919746 ) ) ; +#22663 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22664 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22665 = ORIENTED_EDGE ( 'NONE', *, *, #20230, .T. ) ; +#22666 = ADVANCED_FACE ( 'NONE', ( #85414 ), #39972, .T. ) ; +#22667 = PRESENTATION_STYLE_ASSIGNMENT (( #6270 ) ) ; +#22668 = ORIENTED_EDGE ( 'NONE', *, *, #61542, .F. ) ; +#22669 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69073 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79870, #40049, #71691 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22670 = VERTEX_POINT ( 'NONE', #1154 ) ; +#22671 = EDGE_LOOP ( 'NONE', ( #70770, #18316, #83608, #48482 ) ) ; +#22672 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1481 ), #50422 ) ; +#22673 = FILL_AREA_STYLE ('',( #100154 ) ) ; +#22675 = FILL_AREA_STYLE_COLOUR ( '', #20440 ) ; +#22674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22676 = FACE_OUTER_BOUND ( 'NONE', #22272, .T. ) ; +#22677 = VECTOR ( 'NONE', #95501, 1000.000000000000000 ) ; +#22678 = VERTEX_POINT ( 'NONE', #72125 ) ; +#22679 = PRESENTATION_STYLE_ASSIGNMENT (( #100159 ) ) ; +#22680 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22681 = ORIENTED_EDGE ( 'NONE', *, *, #46657, .F. ) ; +#22682 = LINE ( 'NONE', #53822, #40028 ) ; +#22683 = ADVANCED_FACE ( 'NONE', ( #62978 ), #32315, .T. ) ; +#22684 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#22685 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22686 = ORIENTED_EDGE ( 'NONE', *, *, #25686, .T. ) ; +#22688 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22687 = CARTESIAN_POINT ( 'NONE', ( 1.726282678897219869, -1.159841243706410063, 0.8099999999999998312 ) ) ; +#22689 = EDGE_LOOP ( 'NONE', ( #43146, #3709, #3706, #66502 ) ) ; +#22690 = EDGE_CURVE ( 'NONE', #20599, #73465, #88441, .T. ) ; +#22692 = FACE_OUTER_BOUND ( 'NONE', #49650, .T. ) ; +#22691 = SURFACE_SIDE_STYLE ('',( #54865 ) ) ; +#22693 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22695 = EDGE_CURVE ( 'NONE', #73043, #79986, #11869, .T. ) ; +#22694 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#22696 = VECTOR ( 'NONE', #85669, 1000.000000000000000 ) ; +#22697 = VERTEX_POINT ( 'NONE', #49663 ) ; +#22698 = ORIENTED_EDGE ( 'NONE', *, *, #24587, .F. ) ; +#22699 = SURFACE_SIDE_STYLE ('',( #45628 ) ) ; +#22700 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22701 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.266666666666667052, 0.000000000000000000 ) ) ; +#22702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85918, 'distance_accuracy_value', 'NONE'); +#22703 = VECTOR ( 'NONE', #14540, 1000.000000000000000 ) ; +#22704 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22705 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95184 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35527, #65629, #3358 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22706 = FILL_AREA_STYLE ('',( #92609 ) ) ; +#22707 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22708 = SURFACE_SIDE_STYLE ('',( #71180 ) ) ; +#22709 = PRESENTATION_STYLE_ASSIGNMENT (( #46149 ) ) ; +#22710 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24347 ) ) ; +#22711 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#22712 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91152 ) ) ; +#22713 = ORIENTED_EDGE ( 'NONE', *, *, #48768, .T. ) ; +#22714 = EDGE_CURVE ( 'NONE', #96275, #56137, #51169, .T. ) ; +#22716 = PRESENTATION_STYLE_ASSIGNMENT (( #31377 ) ) ; +#22715 = FACE_OUTER_BOUND ( 'NONE', #3327, .T. ) ; +#22717 = SURFACE_SIDE_STYLE ('',( #76834 ) ) ; +#22718 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25344 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84946, #77285, #54326 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22719 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#22720 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#22721 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63565 ), #87955 ) ; +#22722 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91230 ) ) ; +#22723 = DIRECTION ( 'NONE', ( 0.7071067811865445751, 0.7071067811865504593, 0.000000000000000000 ) ) ; +#22724 = LINE ( 'NONE', #45659, #89341 ) ; +#22725 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22726 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #33277, #24116, #32266, #94519 ), + ( #40947, #55756, #48088, #71575 ), + ( #89397, #57795, #26630, #58797 ), + ( #13216, #90391, #66909, #88905 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243634942, 0.8047378541243634942, 1.000000000000000000), + ( 0.8047378541243662697, 0.6476030138606875264, 0.6476030138606875264, 0.8047378541243662697), + ( 0.8047378541243662697, 0.6476030138606875264, 0.6476030138606875264, 0.8047378541243662697), + ( 1.000000000000000000, 0.8047378541243634942, 0.8047378541243634942, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#22727 = AXIS2_PLACEMENT_3D ( 'NONE', #4395, #20729, #90159 ) ; +#22729 = VERTEX_POINT ( 'NONE', #35364 ) ; +#22728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11200 ), #43933 ) ; +#22730 = EDGE_CURVE ( 'NONE', #24985, #29467, #36391, .T. ) ; +#22731 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#22732 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22733 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#22734 = LINE ( 'NONE', #99716, #95112 ) ; +#22735 = FACE_OUTER_BOUND ( 'NONE', #82117, .T. ) ; +#22736 = AXIS2_PLACEMENT_3D ( 'NONE', #46680, #94654, #63052 ) ; +#22737 = SURFACE_SIDE_STYLE ('',( #60069 ) ) ; +#22738 = EDGE_CURVE ( 'NONE', #18215, #7518, #81323, .T. ) ; +#22739 = LINE ( 'NONE', #13488, #95181 ) ; +#22740 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#22741 = FILL_AREA_STYLE_COLOUR ( '', #75307 ) ; +#22742 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22743 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22744 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22745 = AXIS2_PLACEMENT_3D ( 'NONE', #92851, #46926, #7044 ) ; +#22746 = LINE ( 'NONE', #38070, #68198 ) ; +#22747 = AXIS2_PLACEMENT_3D ( 'NONE', #89780, #74482, #35690 ) ; +#22748 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#22749 = EDGE_CURVE ( 'NONE', #87090, #56373, #80808, .T. ) ; +#22750 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40262, 'distance_accuracy_value', 'NONE'); +#22751 = SURFACE_STYLE_USAGE ( .BOTH. , #45185 ) ; +#22752 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39996, 'distance_accuracy_value', 'NONE'); +#22753 = FILL_AREA_STYLE_COLOUR ( '', #16126 ) ; +#22754 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, -0.000000000000000000 ) ) ; +#22755 = CIRCLE ( 'NONE', #55368, 0.3000000000000000444 ) ; +#22757 = EDGE_CURVE ( 'NONE', #43767, #38287, #42000, .T. ) ; +#22756 = CYLINDRICAL_SURFACE ( 'NONE', #52032, 0.1999999999999996503 ) ; +#22758 = CARTESIAN_POINT ( 'NONE', ( -1.293371091536239970, -1.061634207873779934, 0.8299999999999999600 ) ) ; +#22759 = ORIENTED_EDGE ( 'NONE', *, *, #9528, .F. ) ; +#22760 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75860, 'distance_accuracy_value', 'NONE'); +#22761 = FILL_AREA_STYLE ('',( #92660 ) ) ; +#22762 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#22763 = VECTOR ( 'NONE', #5110, 1000.000000000000000 ) ; +#22764 = ORIENTED_EDGE ( 'NONE', *, *, #49193, .T. ) ; +#22765 = ADVANCED_FACE ( 'NONE', ( #96575 ), #18983, .T. ) ; +#22766 = PRESENTATION_STYLE_ASSIGNMENT (( #45695 ) ) ; +#22767 = SURFACE_STYLE_FILL_AREA ( #85543 ) ; +#22768 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#22769 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22770 = ORIENTED_EDGE ( 'NONE', *, *, #18477, .F. ) ; +#22772 = EDGE_CURVE ( 'NONE', #61666, #83836, #87937, .T. ) ; +#22771 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72476 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25935, #87191, #18725 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22773 = EDGE_CURVE ( 'NONE', #60355, #60733, #30199, .T. ) ; +#22774 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22775 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48340, 'distance_accuracy_value', 'NONE'); +#22776 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22777 = ORIENTED_EDGE ( 'NONE', *, *, #14244, .F. ) ; +#22778 = EDGE_LOOP ( 'NONE', ( #98789, #80576, #42409, #3609, #6895, #19344 ) ) ; +#22779 = EDGE_CURVE ( 'NONE', #25877, #10670, #89897, .T. ) ; +#22780 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#22781 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#22782 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22783 = EDGE_LOOP ( 'NONE', ( #54055, #93626, #11531, #60764 ) ) ; +#22784 = CARTESIAN_POINT ( 'NONE', ( -0.01460762007543630128, -1.490633633148249926, 0.8100000000000000533 ) ) ; +#22785 = CARTESIAN_POINT ( 'NONE', ( 0.5451074176016761363, -1.092033457943389907, 0.8299999999999999600 ) ) ; +#22786 = FILL_AREA_STYLE_COLOUR ( '', #50117 ) ; +#22787 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22788 = PRESENTATION_STYLE_ASSIGNMENT (( #76392 ) ) ; +#22789 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #42652, #92097 ), + ( #90617, #98195 ), + ( #75298, #74797 ), + ( #82468, #83461 ), + ( #12922, #83953 ), + ( #44138, #76281 ), + ( #52822, #12421 ), + ( #13420, #29329 ), + ( #90098, #59014 ), + ( #82959, #98682 ), + ( #51825, #6280 ), + ( #13955, #4342 ), + ( #60005, #44620 ), + ( #37508, #60994 ), + ( #5803, #20654 ), + ( #20149, #5295 ), + ( #22165, #36513 ), + ( #52333, #68612 ), + ( #35514, #99660 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07149115047970650005, 0.1387482511670830032, 0.2024524341567409957, 0.2636912508091490137, 0.3230850051389609900, 0.3813511167042549777, 0.4391309649659340120, 0.4974277397290590153, 0.5562304511353209913, 0.6156242054651339668, 0.6763078083294490339, 0.7386509055408320146, 0.8025070736687720530, 0.8670020345552610364, 0.9328234660649350474, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22790 = CIRCLE ( 'NONE', #96151, 0.5799999999999999600 ) ; +#22791 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43993 ) ) ; +#22792 = SURFACE_STYLE_USAGE ( .BOTH. , #77398 ) ; +#22793 = ORIENTED_EDGE ( 'NONE', *, *, #46281, .T. ) ; +#22794 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74916 ) ) ; +#22795 = ORIENTED_EDGE ( 'NONE', *, *, #71563, .F. ) ; +#22797 = PLANE ( 'NONE', #72072 ) ; +#22796 = AXIS2_PLACEMENT_3D ( 'NONE', #50813, #36976, #5276 ) ; +#22798 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22799 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84162, #98393, #68805, #44327, #5503, #67808, #98889, #29037, #62707, #55572, #76994, #6965, #7470, #94307, #1421, #100846, #69292, #30495, #40231, #92778, #93781, #63225, #93287, #46327, #84652, #385, #61706, #38204, #23914, #85666, #32058, #70333, #38699, #22895, #24422, #78503 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 1, 1, 1, 2, 2, 1, 2, 2, 1, 1, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.06249999999999784894, 0.1249999999999956979, 0.1874999999999935607, 0.2187499999999928668, 0.2499999999999921729, 0.3749999999999842348, 0.4374999999999796829, 0.4687499999999773515, 0.4843749999999757416, 0.4999999999999740763, 0.5624999999999723554, 0.5937499999999720224, 0.6249999999999716893, 0.6874999999999721334, 0.7187499999999724665, 0.7343749999999736877, 0.7499999999999749090, 0.8124999999999804601, 0.8437499999999832356, 0.8749999999999861222, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22800 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33907, #44040, #75205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22801 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22802 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#22803 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#22804 = AXIS2_PLACEMENT_3D ( 'NONE', #47227, #91662, #8331 ) ; +#22805 = ORIENTED_EDGE ( 'NONE', *, *, #83068, .F. ) ; +#22806 = CARTESIAN_POINT ( 'NONE', ( 5.264745041625020328, 6.971255041625060045, 0.8648700000000000276 ) ) ; +#22807 = STYLED_ITEM ( 'NONE', ( #43947 ), #80601 ) ; +#22808 = PLANE ( 'NONE', #95519 ) ; +#22809 = ORIENTED_EDGE ( 'NONE', *, *, #55793, .F. ) ; +#22811 = CARTESIAN_POINT ( 'NONE', ( -0.8909255146275300019, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#22810 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22812 = EDGE_LOOP ( 'NONE', ( #30066, #85167, #25785, #12351, #92338, #43130 ) ) ; +#22813 = VERTEX_POINT ( 'NONE', #17965 ) ; +#22814 = LINE ( 'NONE', #62646, #42874 ) ; +#22815 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#22816 = VECTOR ( 'NONE', #11577, 1000.000000000000000 ) ; +#22817 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22818 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14599 ), #16217 ) ; +#22819 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#22821 = EDGE_CURVE ( 'NONE', #3964, #9287, #58352, .T. ) ; +#22820 = PLANE ( 'NONE', #21248 ) ; +#22823 = ORIENTED_EDGE ( 'NONE', *, *, #88782, .T. ) ; +#22822 = SURFACE_STYLE_FILL_AREA ( #22300 ) ; +#22824 = STYLED_ITEM ( 'NONE', ( #52233 ), #75635 ) ; +#22826 = AXIS2_PLACEMENT_3D ( 'NONE', #76329, #67653, #6808 ) ; +#22825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#22827 = LINE ( 'NONE', #92720, #42079 ) ; +#22828 = CARTESIAN_POINT ( 'NONE', ( 0.1554794570581656543, 0.3979707056443637092, 0.8100000000000000533 ) ) ; +#22829 = ORIENTED_EDGE ( 'NONE', *, *, #11922, .T. ) ; +#22831 = SURFACE_SIDE_STYLE ('',( #62654 ) ) ; +#22830 = FILL_AREA_STYLE ('',( #62653 ) ) ; +#22832 = ORIENTED_EDGE ( 'NONE', *, *, #27994, .T. ) ; +#22833 = ADVANCED_FACE ( 'NONE', ( #59360 ), #28175, .T. ) ; +#22834 = ORIENTED_EDGE ( 'NONE', *, *, #86747, .T. ) ; +#22835 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22836 = SURFACE_STYLE_FILL_AREA ( #100304 ) ; +#22837 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#22838 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725634999999999586, 0.8648700000000000276 ) ) ; +#22839 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22840 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63607 ) ) ; +#22841 = SURFACE_STYLE_USAGE ( .BOTH. , #70284 ) ; +#22842 = LINE ( 'NONE', #68267, #39681 ) ; +#22844 = SURFACE_STYLE_USAGE ( .BOTH. , #5945 ) ; +#22843 = VECTOR ( 'NONE', #54537, 1000.000000000000000 ) ; +#22845 = SURFACE_STYLE_USAGE ( .BOTH. , #29489 ) ; +#22846 = ORIENTED_EDGE ( 'NONE', *, *, #7807, .T. ) ; +#22847 = ORIENTED_EDGE ( 'NONE', *, *, #78337, .T. ) ; +#22848 = EDGE_CURVE ( 'NONE', #56731, #61861, #29656, .T. ) ; +#22849 = PRESENTATION_STYLE_ASSIGNMENT (( #55013 ) ) ; +#22850 = FILL_AREA_STYLE_COLOUR ( '', #54682 ) ; +#22851 = AXIS2_PLACEMENT_3D ( 'NONE', #48797, #41623, #88567 ) ; +#22852 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22853 = FILL_AREA_STYLE ('',( #71317 ) ) ; +#22854 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8648700000000000276 ) ) ; +#22855 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22856 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22857 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22858 = FILL_AREA_STYLE_COLOUR ( '', #2085 ) ; +#22859 = ORIENTED_EDGE ( 'NONE', *, *, #55056, .T. ) ; +#22860 = EDGE_CURVE ( 'NONE', #49312, #47892, #52663, .T. ) ; +#22861 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#22862 = SURFACE_STYLE_FILL_AREA ( #92278 ) ; +#22863 = SURFACE_STYLE_USAGE ( .BOTH. , #38182 ) ; +#22864 = PLANE ( 'NONE', #90183 ) ; +#22865 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#22866 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67676 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86943, #78759, #71107 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#22867 = PRESENTATION_STYLE_ASSIGNMENT (( #15142 ) ) ; +#22868 = SURFACE_SIDE_STYLE ('',( #89297 ) ) ; +#22869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89610, 'distance_accuracy_value', 'NONE'); +#22870 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#22871 = AXIS2_PLACEMENT_3D ( 'NONE', #70773, #31985, #2361 ) ; +#22872 = VECTOR ( 'NONE', #81988, 1000.000000000000000 ) ; +#22873 = LINE ( 'NONE', #54005, #8008 ) ; +#22874 = SURFACE_STYLE_USAGE ( .BOTH. , #53511 ) ; +#22875 = FILL_AREA_STYLE_COLOUR ( '', #97680 ) ; +#22876 = FILL_AREA_STYLE ('',( #44807 ) ) ; +#22877 = EDGE_CURVE ( 'NONE', #81673, #90329, #90443, .T. ) ; +#22878 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24511 ), #86421 ) ; +#22879 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#22880 = SURFACE_STYLE_USAGE ( .BOTH. , #75483 ) ; +#22881 = STYLED_ITEM ( 'NONE', ( #79619 ), #94344 ) ; +#22882 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #14261, 'design' ) ; +#22883 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4913 ) ) ; +#22884 = ADVANCED_FACE ( 'NONE', ( #60839 ), #90957, .T. ) ; +#22885 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22886 = EDGE_LOOP ( 'NONE', ( #18858, #57229, #7851, #42292 ) ) ; +#22887 = PLANE ( 'NONE', #85338 ) ; +#22888 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94571 ), #6478 ) ; +#22889 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2750000000000000222, 0.1499999999999999667 ) ) ; +#22890 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#22891 = SURFACE_STYLE_USAGE ( .BOTH. , #83163 ) ; +#22892 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56913, 'distance_accuracy_value', 'NONE'); +#22893 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22894 = VECTOR ( 'NONE', #20210, 1000.000000000000000 ) ; +#22895 = CARTESIAN_POINT ( 'NONE', ( 1.069885645311858147, -1.099280448394919452, 0.8099999999999276667 ) ) ; +#22896 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45646 ) ) ; +#22897 = ORIENTED_EDGE ( 'NONE', *, *, #6357, .T. ) ; +#22898 = VECTOR ( 'NONE', #96671, 1000.000000000000000 ) ; +#22899 = DIRECTION ( 'NONE', ( -0.7071067811865445751, -0.7071067811865504593, 0.000000000000000000 ) ) ; +#22900 = VECTOR ( 'NONE', #82097, 1000.000000000000000 ) ; +#22901 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#22902 = EDGE_CURVE ( 'NONE', #24940, #28694, #53165, .T. ) ; +#22903 = VECTOR ( 'NONE', #48107, 1000.000000000000000 ) ; +#22904 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333316872, -1.899999999999999911, 1.747825839084584091E-76 ) ) ; +#22905 = ADVANCED_FACE ( 'NONE', ( #37838 ), #59856, .T. ) ; +#22906 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#22907 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93580, 'distance_accuracy_value', 'NONE'); +#22908 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100505, #30666, #61857, #85307 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#22909 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79440, 'distance_accuracy_value', 'NONE'); +#22910 = CARTESIAN_POINT ( 'NONE', ( 8.559863124875013440, 2.134644875124987795, 0.8991599999999999593 ) ) ; +#22911 = ORIENTED_EDGE ( 'NONE', *, *, #52582, .F. ) ; +#22912 = ORIENTED_EDGE ( 'NONE', *, *, #77261, .T. ) ; +#22913 = EDGE_CURVE ( 'NONE', #77676, #38629, #77639, .T. ) ; +#22914 = CARTESIAN_POINT ( 'NONE', ( 6.084989499499824817, 10.26637249949982689, 0.8991599999999999593 ) ) ; +#22915 = ORIENTED_EDGE ( 'NONE', *, *, #72548, .T. ) ; +#22917 = FILL_AREA_STYLE ('',( #53049 ) ) ; +#22916 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66919 ) ) ; +#22918 = PRESENTATION_STYLE_ASSIGNMENT (( #24446 ) ) ; +#22919 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 7.700000000000000178, 0.8648700000000000276 ) ) ; +#22920 = VECTOR ( 'NONE', #76352, 1000.000000000000000 ) ; +#22921 = EDGE_CURVE ( 'NONE', #13319, #81461, #93422, .T. ) ; +#22922 = FACE_OUTER_BOUND ( 'NONE', #42504, .T. ) ; +#22923 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#22924 = PRESENTATION_STYLE_ASSIGNMENT (( #15189 ) ) ; +#22926 = EDGE_LOOP ( 'NONE', ( #35896, #37786, #61772, #28964 ) ) ; +#22925 = ORIENTED_EDGE ( 'NONE', *, *, #92024, .F. ) ; +#22927 = ORIENTED_EDGE ( 'NONE', *, *, #79843, .F. ) ; +#22929 = SURFACE_STYLE_USAGE ( .BOTH. , #1459 ) ; +#22928 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#22930 = ORIENTED_EDGE ( 'NONE', *, *, #22404, .T. ) ; +#22931 = ORIENTED_EDGE ( 'NONE', *, *, #76199, .T. ) ; +#22932 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 8.802661000000002289, 0.8991599999999999593 ) ) ; +#22933 = FACE_OUTER_BOUND ( 'NONE', #679, .T. ) ; +#22934 = VECTOR ( 'NONE', #4851, 1000.000000000000000 ) ; +#22935 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76698 ), #96223 ) ; +#22937 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#22936 = FILL_AREA_STYLE ('',( #51086 ) ) ; +#22938 = EDGE_LOOP ( 'NONE', ( #85568, #45218, #24543, #31693 ) ) ; +#22939 = CARTESIAN_POINT ( 'NONE', ( -0.4939768715539690214, -0.9855649010623360740, 0.8100000000000000533 ) ) ; +#22940 = EDGE_LOOP ( 'NONE', ( #100374, #87749, #48190, #13779 ) ) ; +#22941 = EDGE_LOOP ( 'NONE', ( #64472, #48439, #7380, #23548 ) ) ; +#22942 = CARTESIAN_POINT ( 'NONE', ( 0.2473788005703330406, -1.399092671493430196, 0.8300000000000004041 ) ) ; +#22943 = STYLED_ITEM ( 'NONE', ( #47684 ), #86453 ) ; +#22944 = VECTOR ( 'NONE', #47174, 1000.000000000000000 ) ; +#22945 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#22946 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#22947 = VERTEX_POINT ( 'NONE', #23532 ) ; +#22948 = STYLED_ITEM ( 'NONE', ( #16510 ), #85871 ) ; +#22949 = PRESENTATION_STYLE_ASSIGNMENT (( #39770 ) ) ; +#22950 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52331 ), #1820 ) ; +#22951 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#22952 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22953 = VERTEX_POINT ( 'NONE', #56196 ) ; +#22954 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37609 ) ) ; +#22956 = FILL_AREA_STYLE ('',( #40795 ) ) ; +#22955 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#22957 = PRESENTATION_STYLE_ASSIGNMENT (( #30562 ) ) ; +#22958 = VERTEX_POINT ( 'NONE', #63851 ) ; +#22959 = EDGE_CURVE ( 'NONE', #31058, #44731, #94944, .T. ) ; +#22960 = ORIENTED_EDGE ( 'NONE', *, *, #58244, .F. ) ; +#22961 = SURFACE_SIDE_STYLE ('',( #62778 ) ) ; +#22962 = AXIS2_PLACEMENT_3D ( 'NONE', #15078, #54459, #85571 ) ; +#22963 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#22964 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.000000000000000000 ) ) ; +#22965 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9815 ), #53998 ) ; +#22966 = CARTESIAN_POINT ( 'NONE', ( 1.006730632090929944, -1.141526082476280068, 0.8299999999999997380 ) ) ; +#22967 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#22968 = CARTESIAN_POINT ( 'NONE', ( 0.1868680034464730022, -1.007635622941599918, 0.8300000000000020695 ) ) ; +#22969 = STYLED_ITEM ( 'NONE', ( #65051 ), #64634 ) ; +#22970 = ORIENTED_EDGE ( 'NONE', *, *, #21783, .T. ) ; +#22971 = FILL_AREA_STYLE_COLOUR ( '', #11409 ) ; +#22972 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86516 ) ) ; +#22973 = CARTESIAN_POINT ( 'NONE', ( 0.09190937866851861537, -1.304291937284929981, 0.8100000000000000533 ) ) ; +#22974 = EDGE_LOOP ( 'NONE', ( #10277, #78498, #71631, #94527 ) ) ; +#22975 = VECTOR ( 'NONE', #55489, 1000.000000000000000 ) ; +#22976 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.000000000000000000 ) ) ; +#22977 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#22979 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25459, 'distance_accuracy_value', 'NONE'); +#22978 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22980 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#22981 = SURFACE_STYLE_USAGE ( .BOTH. , #21448 ) ; +#22982 = CARTESIAN_POINT ( 'NONE', ( 1.798434352155980021, -1.039339352017210061, 0.8299999999999999600 ) ) ; +#22983 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#22984 = FACE_OUTER_BOUND ( 'NONE', #67052, .T. ) ; +#22985 = SURFACE_STYLE_FILL_AREA ( #14758 ) ; +#22986 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#22987 = SURFACE_STYLE_FILL_AREA ( #77594 ) ; +#22988 = AXIS2_PLACEMENT_3D ( 'NONE', #53382, #44197, #14019 ) ; +#22989 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#22990 = PLANE ( 'NONE', #70795 ) ; +#22991 = EDGE_CURVE ( 'NONE', #62776, #14672, #70987, .T. ) ; +#22992 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#22993 = DIRECTION ( 'NONE', ( 0.7071075504167442238, -0.7071060119555140355, 0.000000000000000000 ) ) ; +#22994 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999940048, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#22996 = AXIS2_PLACEMENT_3D ( 'NONE', #52176, #29180, #52667 ) ; +#22995 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#22997 = SURFACE_STYLE_FILL_AREA ( #93876 ) ; +#22998 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44701, 'distance_accuracy_value', 'NONE'); +#22999 = ORIENTED_EDGE ( 'NONE', *, *, #45025, .T. ) ; +#23000 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23002 = EDGE_CURVE ( 'NONE', #59682, #85949, #86303, .T. ) ; +#23001 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23003 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23004 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#23005 = LINE ( 'NONE', #78131, #53582 ) ; +#23006 = STYLED_ITEM ( 'NONE', ( #74709 ), #18245 ) ; +#23007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23008 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84928 ) ) ; +#23009 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23010 = SURFACE_STYLE_FILL_AREA ( #7078 ) ; +#23011 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23012 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #63191 ) ; +#23013 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60565 ), #34482 ) ; +#23014 = ORIENTED_EDGE ( 'NONE', *, *, #96042, .F. ) ; +#23015 = FILL_AREA_STYLE_COLOUR ( '', #13874 ) ; +#23016 = ORIENTED_EDGE ( 'NONE', *, *, #31750, .T. ) ; +#23017 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#23018 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47422 ), #68607 ) ; +#23019 = FILL_AREA_STYLE_COLOUR ( '', #25477 ) ; +#23020 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23021 = EDGE_CURVE ( 'NONE', #95862, #19901, #55699, .T. ) ; +#23022 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72000 ) ) ; +#23023 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23024 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #72236, #87973 ) ; +#23025 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8100000000000271427 ) ) ; +#23026 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#23027 = ORIENTED_EDGE ( 'NONE', *, *, #75455, .T. ) ; +#23028 = CARTESIAN_POINT ( 'NONE', ( 1.169384343503750090, -0.9551946040733080290, 0.8300000000000002931 ) ) ; +#23029 = FILL_AREA_STYLE_COLOUR ( '', #4706 ) ; +#23030 = VECTOR ( 'NONE', #90615, 1000.000000000000000 ) ; +#23031 = FACE_BOUND ( 'NONE', #42599, .T. ) ; +#23032 = EDGE_LOOP ( 'NONE', ( #99318, #85834, #9606, #90723 ) ) ; +#23033 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23034 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, -0.6500000000000001332 ) ) ; +#23035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5060 ) ) ; +#23036 = ORIENTED_EDGE ( 'NONE', *, *, #50782, .F. ) ; +#23037 = CARTESIAN_POINT ( 'NONE', ( 1.078134533378849902, -1.401744930657430110, 0.8299999999999999600 ) ) ; +#23038 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23039 = EDGE_CURVE ( 'NONE', #32337, #76527, #77783, .T. ) ; +#23040 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23041 = AXIS2_PLACEMENT_3D ( 'NONE', #2149, #16919, #48101 ) ; +#23042 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23043 = CARTESIAN_POINT ( 'NONE', ( 1.872286628785889917, -1.103202958186300320, 0.8100000000000000533 ) ) ; +#23044 = LINE ( 'NONE', #15841, #68475 ) ; +#23045 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#23046 = AXIS2_PLACEMENT_3D ( 'NONE', #10196, #73103, #72581 ) ; +#23048 = ORIENTED_EDGE ( 'NONE', *, *, #12788, .F. ) ; +#23047 = ORIENTED_EDGE ( 'NONE', *, *, #41540, .T. ) ; +#23049 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26334 ) ) ; +#23050 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23051 = ORIENTED_EDGE ( 'NONE', *, *, #93264, .T. ) ; +#23052 = CARTESIAN_POINT ( 'NONE', ( -0.4841855288935910107, -0.9911177488655089629, 0.8299999999999999600 ) ) ; +#23053 = ORIENTED_EDGE ( 'NONE', *, *, #69000, .T. ) ; +#23054 = ORIENTED_EDGE ( 'NONE', *, *, #69716, .F. ) ; +#23055 = LINE ( 'NONE', #93452, #90611 ) ; +#23056 = FACE_OUTER_BOUND ( 'NONE', #38081, .T. ) ; +#23057 = PLANE ( 'NONE', #20903 ) ; +#23058 = STYLED_ITEM ( 'NONE', ( #79000 ), #51679 ) ; +#23060 = PRESENTATION_STYLE_ASSIGNMENT (( #92943 ) ) ; +#23059 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#23061 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23062 = ORIENTED_EDGE ( 'NONE', *, *, #36143, .F. ) ; +#23063 = ORIENTED_EDGE ( 'NONE', *, *, #6249, .T. ) ; +#23064 = SURFACE_SIDE_STYLE ('',( #24081 ) ) ; +#23065 = STYLED_ITEM ( 'NONE', ( #17743 ), #46304 ) ; +#23066 = ORIENTED_EDGE ( 'NONE', *, *, #95294, .F. ) ; +#23067 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23068 = EDGE_CURVE ( 'NONE', #9663, #16675, #7597, .T. ) ; +#23070 = ORIENTED_EDGE ( 'NONE', *, *, #99755, .T. ) ; +#23069 = LINE ( 'NONE', #54203, #60783 ) ; +#23071 = LINE ( 'NONE', #54205, #11434 ) ; +#23072 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23073 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#23074 = EDGE_LOOP ( 'NONE', ( #100807, #93428, #80694, #7012 ) ) ; +#23075 = ORIENTED_EDGE ( 'NONE', *, *, #47644, .F. ) ; +#23076 = EDGE_CURVE ( 'NONE', #80825, #44979, #47496, .T. ) ; +#23077 = PLANE ( 'NONE', #18764 ) ; +#23078 = SURFACE_STYLE_USAGE ( .BOTH. , #24098 ) ; +#23079 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9926 ), #57353 ) ; +#23081 = ORIENTED_EDGE ( 'NONE', *, *, #5880, .T. ) ; +#23080 = LINE ( 'NONE', #62394, #73808 ) ; +#23082 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81005, #95760, #64161 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23083 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23084 = PLANE ( 'NONE', #4735 ) ; +#23085 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41462 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3549, #43337, #96427 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23086 = SURFACE_STYLE_FILL_AREA ( #7156 ) ; +#23087 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23088 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #83978, #68630, #99679, #29836 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23089 = FACE_OUTER_BOUND ( 'NONE', #31647, .T. ) ; +#23090 = PLANE ( 'NONE', #97740 ) ; +#23091 = EDGE_LOOP ( 'NONE', ( #23683, #59317, #100838, #165 ) ) ; +#23092 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23093 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#23094 = SURFACE_STYLE_USAGE ( .BOTH. , #9692 ) ; +#23095 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#23096 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23098 = SURFACE_STYLE_USAGE ( .BOTH. , #32766 ) ; +#23097 = CARTESIAN_POINT ( 'NONE', ( 0.4626002664603570125, -1.036644144574919935, 0.8100000000000000533 ) ) ; +#23099 = LINE ( 'NONE', #45028, #66319 ) ; +#23100 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571429047, 0.6899999999999999467, 0.5000000000000003331 ) ) ; +#23101 = STYLED_ITEM ( 'NONE', ( #79212 ), #7560 ) ; +#23102 = CYLINDRICAL_SURFACE ( 'NONE', #59200, 0.01000000000000002623 ) ; +#23103 = VECTOR ( 'NONE', #21479, 1000.000000000000000 ) ; +#23104 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.100000000000000311, 1.048695503451053346E-76 ) ) ; +#23105 = ORIENTED_EDGE ( 'NONE', *, *, #74843, .T. ) ; +#23106 = EDGE_CURVE ( 'NONE', #37700, #60603, #93914, .T. ) ; +#23107 = EDGE_CURVE ( 'NONE', #14090, #66049, #8600, .T. ) ; +#23108 = SURFACE_STYLE_FILL_AREA ( #77716 ) ; +#23109 = SURFACE_STYLE_FILL_AREA ( #38920 ) ; +#23110 = ORIENTED_EDGE ( 'NONE', *, *, #14971, .T. ) ; +#23111 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23112 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -13.40000000000000036 ) ) ; +#23113 = SURFACE_STYLE_USAGE ( .BOTH. , #61923 ) ; +#23114 = FACE_OUTER_BOUND ( 'NONE', #100669, .T. ) ; +#23115 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#23116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55859 ), #88348 ) ; +#23117 = ORIENTED_EDGE ( 'NONE', *, *, #55604, .T. ) ; +#23118 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#23119 = EDGE_CURVE ( 'NONE', #35535, #9771, #54685, .T. ) ; +#23120 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23121 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999959338, -0.1399999999999999856 ) ) ; +#23122 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544766999999999779, 0.8991599999999999593 ) ) ; +#23123 = EDGE_CURVE ( 'NONE', #63754, #42980, #63366, .T. ) ; +#23124 = SURFACE_STYLE_FILL_AREA ( #94539 ) ; +#23125 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#23126 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#23127 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1920 ), #80216 ) ; +#23128 = PLANE ( 'NONE', #49188 ) ; +#23129 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23130 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#23131 = CARTESIAN_POINT ( 'NONE', ( -0.03988517032605130158, -0.9096959278232360502, 0.8100000000000000533 ) ) ; +#23132 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23133 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23134 = ORIENTED_EDGE ( 'NONE', *, *, #41567, .F. ) ; +#23135 = EDGE_LOOP ( 'NONE', ( #15075, #27479, #49701, #79815 ) ) ; +#23136 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80226 ) ) ; +#23137 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#23138 = FILL_AREA_STYLE_COLOUR ( '', #40718 ) ; +#23139 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#23140 = SURFACE_STYLE_USAGE ( .BOTH. , #36950 ) ; +#23141 = SURFACE_SIDE_STYLE ('',( #77235 ) ) ; +#23142 = EDGE_CURVE ( 'NONE', #53046, #97953, #76506, .T. ) ; +#23143 = FILL_AREA_STYLE_COLOUR ( '', #26030 ) ; +#23144 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23145 = PLANE ( 'NONE', #85225 ) ; +#23146 = ORIENTED_EDGE ( 'NONE', *, *, #87115, .F. ) ; +#23147 = FILL_AREA_STYLE_COLOUR ( '', #19959 ) ; +#23148 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23149 = VERTEX_POINT ( 'NONE', #46991 ) ; +#23150 = SURFACE_SIDE_STYLE ('',( #7233 ) ) ; +#23151 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27950 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77841, #70169, #68653 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23152 = FILL_AREA_STYLE ('',( #46074 ) ) ; +#23153 = ORIENTED_EDGE ( 'NONE', *, *, #40357, .F. ) ; +#23154 = FILL_AREA_STYLE_COLOUR ( '', #28317 ) ; +#23155 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#23156 = AXIS2_PLACEMENT_3D ( 'NONE', #4032, #87792, #88799 ) ; +#23157 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23158 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23160 = ADVANCED_FACE ( 'NONE', ( #79678 ), #9622, .T. ) ; +#23159 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#23161 = PRESENTATION_STYLE_ASSIGNMENT (( #71123 ) ) ; +#23162 = LINE ( 'NONE', #50196, #72398 ) ; +#23163 = ORIENTED_EDGE ( 'NONE', *, *, #35180, .T. ) ; +#23164 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37806 ) ) ; +#23166 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#23167 = VERTEX_POINT ( 'NONE', #95953 ) ; +#23168 = PRESENTATION_STYLE_ASSIGNMENT (( #93056 ) ) ; +#23169 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23170 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23171 = SURFACE_STYLE_USAGE ( .BOTH. , #76775 ) ; +#23172 = SURFACE_SIDE_STYLE ('',( #52809 ) ) ; +#23173 = ORIENTED_EDGE ( 'NONE', *, *, #72091, .F. ) ; +#23174 = VERTEX_POINT ( 'NONE', #74014 ) ; +#23175 = FILL_AREA_STYLE ('',( #21654 ) ) ; +#23176 = ORIENTED_EDGE ( 'NONE', *, *, #58933, .T. ) ; +#23177 = EDGE_CURVE ( 'NONE', #54059, #45746, #73007, .T. ) ; +#23178 = EDGE_LOOP ( 'NONE', ( #16094, #13038, #81583, #43897 ) ) ; +#23180 = VERTEX_POINT ( 'NONE', #27064 ) ; +#23179 = FILL_AREA_STYLE_COLOUR ( '', #52529 ) ; +#23181 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23183 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.5238200612200850648, -0.02000000000000000042 ) ) ; +#23182 = SURFACE_STYLE_FILL_AREA ( #60993 ) ; +#23184 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#23185 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#23186 = AXIS2_PLACEMENT_3D ( 'NONE', #47630, #62980, #31290 ) ; +#23187 = ORIENTED_EDGE ( 'NONE', *, *, #40112, .F. ) ; +#23188 = LINE ( 'NONE', #7271, #16191 ) ; +#23189 = FILL_AREA_STYLE ('',( #100647 ) ) ; +#23190 = VERTEX_POINT ( 'NONE', #34232 ) ; +#23191 = EDGE_CURVE ( 'NONE', #32383, #73258, #81197, .T. ) ; +#23192 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#23193 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23194 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#23195 = VECTOR ( 'NONE', #89782, 1000.000000000000000 ) ; +#23196 = PRESENTATION_STYLE_ASSIGNMENT (( #62011 ) ) ; +#23197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68779 ) ) ; +#23198 = VERTEX_POINT ( 'NONE', #35236 ) ; +#23199 = EDGE_CURVE ( 'NONE', #62491, #24305, #58723, .T. ) ; +#23200 = SURFACE_STYLE_USAGE ( .BOTH. , #8285 ) ; +#23201 = EDGE_LOOP ( 'NONE', ( #60855, #39477, #30680, #89096 ) ) ; +#23202 = VECTOR ( 'NONE', #3604, 1000.000000000000000 ) ; +#23204 = FILL_AREA_STYLE_COLOUR ( '', #95629 ) ; +#23203 = PRESENTATION_STYLE_ASSIGNMENT (( #31345 ) ) ; +#23205 = ADVANCED_FACE ( 'NONE', ( #96451 ), #19373, .T. ) ; +#23206 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14679 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47901, #79562, #48434 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23207 = STYLED_ITEM ( 'NONE', ( #56221 ), #45852 ) ; +#23208 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#23209 = ORIENTED_EDGE ( 'NONE', *, *, #8813, .T. ) ; +#23210 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89068 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93633, #32913, #55913 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23211 = EDGE_LOOP ( 'NONE', ( #16259, #81683, #87478, #46800, #87223, #69610 ) ) ; +#23212 = FILL_AREA_STYLE ('',( #16018 ) ) ; +#23214 = SURFACE_STYLE_USAGE ( .BOTH. , #67629 ) ; +#23213 = FACE_OUTER_BOUND ( 'NONE', #20517, .T. ) ; +#23215 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#23216 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#23217 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98267 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87210, #48433, #10005 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23218 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23219 = PLANE ( 'NONE', #105 ) ; +#23220 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#23221 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63968 ), #78828 ) ; +#23222 = ADVANCED_FACE ( 'NONE', ( #72007 ), #33205, .T. ) ; +#23224 = EDGE_CURVE ( 'NONE', #28196, #28522, #52539, .T. ) ; +#23223 = SURFACE_STYLE_FILL_AREA ( #46670 ) ; +#23225 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64039 ) ) ; +#23227 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94983 ), #20004 ) ; +#23226 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#23228 = SURFACE_STYLE_USAGE ( .BOTH. , #38037 ) ; +#23229 = SURFACE_STYLE_USAGE ( .BOTH. , #2653 ) ; +#23230 = EDGE_LOOP ( 'NONE', ( #99560, #33300, #2357, #17395, #49533, #74386, #2081, #53171, #8755, #63111, #100793, #19498 ) ) ; +#23231 = SURFACE_SIDE_STYLE ('',( #35559 ) ) ; +#23233 = SURFACE_STYLE_USAGE ( .BOTH. , #99702 ) ; +#23232 = SURFACE_STYLE_FILL_AREA ( #75833 ) ; +#23234 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24866 ) ) ; +#23235 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78687, 'distance_accuracy_value', 'NONE'); +#23236 = FACE_OUTER_BOUND ( 'NONE', #313, .T. ) ; +#23237 = AXIS2_PLACEMENT_3D ( 'NONE', #185, #6279, #22164 ) ; +#23238 = PLANE ( 'NONE', #85943 ) ; +#23239 = LINE ( 'NONE', #54384, #1295 ) ; +#23240 = PLANE ( 'NONE', #41211 ) ; +#23241 = LINE ( 'NONE', #54901, #18443 ) ; +#23242 = EDGE_LOOP ( 'NONE', ( #88093, #41752, #4355, #82167 ) ) ; +#23243 = VECTOR ( 'NONE', #48972, 1000.000000000000114 ) ; +#23244 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#23245 = EDGE_CURVE ( 'NONE', #19992, #65783, #58369, .T. ) ; +#23246 = ADVANCED_FACE ( 'NONE', ( #90325 ), #43358, .T. ) ; +#23247 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#23248 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#23249 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8648700000000000276 ) ) ; +#23250 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#23251 = FACE_OUTER_BOUND ( 'NONE', #40798, .T. ) ; +#23252 = VECTOR ( 'NONE', #64963, 1000.000000000000000 ) ; +#23253 = FILL_AREA_STYLE ('',( #47727 ) ) ; +#23254 = FILL_AREA_STYLE_COLOUR ( '', #27206 ) ; +#23255 = AXIS2_PLACEMENT_3D ( 'NONE', #53768, #44101, #14916 ) ; +#23256 = SURFACE_STYLE_FILL_AREA ( #91661 ) ; +#23257 = FILL_AREA_STYLE ('',( #254 ) ) ; +#23258 = SURFACE_SIDE_STYLE ('',( #85523 ) ) ; +#23259 = STYLED_ITEM ( 'NONE', ( #92960 ), #70329 ) ; +#23260 = EDGE_LOOP ( 'NONE', ( #59901, #43886, #6629, #83011 ) ) ; +#23261 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23263 = EDGE_CURVE ( 'NONE', #93527, #68559, #5521, .T. ) ; +#23264 = SURFACE_STYLE_USAGE ( .BOTH. , #77873 ) ; +#23265 = LINE ( 'NONE', #85531, #47587 ) ; +#23266 = CYLINDRICAL_SURFACE ( 'NONE', #32992, 0.2000000000000000111 ) ; +#23267 = ORIENTED_EDGE ( 'NONE', *, *, #48143, .T. ) ; +#23268 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8100000000000601164 ) ) ; +#23269 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23270 = ADVANCED_FACE ( 'NONE', ( #90837 ), #68817, .T. ) ; +#23271 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12917, #75294, #28330, #20650 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23272 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23273 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23274 = ORIENTED_EDGE ( 'NONE', *, *, #72523, .T. ) ; +#23275 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.499999999999960032, -0.02000000000000000042 ) ) ; +#23276 = EDGE_CURVE ( 'NONE', #14329, #97114, #69837, .T. ) ; +#23277 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, 0.000000000000000000 ) ) ; +#23279 = EDGE_CURVE ( 'NONE', #57125, #26361, #59967, .T. ) ; +#23278 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#23280 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96638 ), #8517 ) ; +#23281 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#23282 = VERTEX_POINT ( 'NONE', #38714 ) ; +#23283 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23284 = CYLINDRICAL_SURFACE ( 'NONE', #40668, 0.05000000000000012768 ) ; +#23285 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7240, 'distance_accuracy_value', 'NONE'); +#23286 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#23287 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36333 ) ) ; +#23288 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85204 ) ) ; +#23289 = ORIENTED_EDGE ( 'NONE', *, *, #19785, .T. ) ; +#23290 = VERTEX_POINT ( 'NONE', #30509 ) ; +#23291 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37931 ) ) ; +#23292 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23293 = ORIENTED_EDGE ( 'NONE', *, *, #88059, .F. ) ; +#23294 = CARTESIAN_POINT ( 'NONE', ( -0.01460762007543630128, -1.490633633148249926, 0.8299999999999999600 ) ) ; +#23295 = CARTESIAN_POINT ( 'NONE', ( 0.4101069733384740124, -1.272991977397700092, 0.8100000000000000533 ) ) ; +#23296 = LINE ( 'NONE', #54452, #33773 ) ; +#23297 = VECTOR ( 'NONE', #84350, 1000.000000000000000 ) ; +#23298 = VECTOR ( 'NONE', #8099, 1000.000000000000000 ) ; +#23299 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#23300 = ADVANCED_FACE ( 'NONE', ( #6972 ), #8485, .F. ) ; +#23301 = VECTOR ( 'NONE', #67481, 1000.000000000000114 ) ; +#23302 = ORIENTED_EDGE ( 'NONE', *, *, #37439, .F. ) ; +#23303 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23304 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45255, 'distance_accuracy_value', 'NONE'); +#23305 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23306 = PLANE ( 'NONE', #82276 ) ; +#23307 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000000804, 12.86860300000000024, 0.8648700000000000276 ) ) ; +#23308 = ADVANCED_FACE ( 'NONE', ( #62723 ), #15705, .T. ) ; +#23309 = ORIENTED_EDGE ( 'NONE', *, *, #64699, .F. ) ; +#23310 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23311 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#23312 = FILL_AREA_STYLE_COLOUR ( '', #27068 ) ; +#23313 = EDGE_LOOP ( 'NONE', ( #33846, #79466, #21999, #73188 ) ) ; +#23314 = EDGE_CURVE ( 'NONE', #78971, #41816, #51055, .T. ) ; +#23316 = SURFACE_SIDE_STYLE ('',( #93203 ) ) ; +#23315 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.000000000000000000 ) ) ; +#23317 = ORIENTED_EDGE ( 'NONE', *, *, #23461, .T. ) ; +#23318 = ORIENTED_EDGE ( 'NONE', *, *, #65181, .F. ) ; +#23319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23321 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#23320 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#23322 = SURFACE_SIDE_STYLE ('',( #100781 ) ) ; +#23324 = EDGE_CURVE ( 'NONE', #77663, #89492, #32070, .T. ) ; +#23323 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#23325 = AXIS2_PLACEMENT_3D ( 'NONE', #97858, #66283, #98339 ) ; +#23326 = VERTEX_POINT ( 'NONE', #81072 ) ; +#23327 = FILL_AREA_STYLE ('',( #84091 ) ) ; +#23328 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#23329 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23330 = SURFACE_STYLE_FILL_AREA ( #93220 ) ; +#23331 = ORIENTED_EDGE ( 'NONE', *, *, #73754, .F. ) ; +#23333 = FILL_AREA_STYLE ('',( #100791 ) ) ; +#23332 = FILL_AREA_STYLE ('',( #6902 ) ) ; +#23334 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#23336 = ORIENTED_EDGE ( 'NONE', *, *, #63364, .T. ) ; +#23335 = CIRCLE ( 'NONE', #80415, 0.1200000000000000927 ) ; +#23338 = ORIENTED_EDGE ( 'NONE', *, *, #58594, .T. ) ; +#23337 = SHAPE_REPRESENTATION ( 'XTAL3225_20210301.xtd', ( #82894 ), #33813 ) ; +#23339 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23340 = CARTESIAN_POINT ( 'NONE', ( 0.9590361231611750359, -1.326636125966530244, 0.8299999999999999600 ) ) ; +#23341 = FILL_AREA_STYLE ('',( #85604 ) ) ; +#23342 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23343 = AXIS2_PLACEMENT_3D ( 'NONE', #67200, #82548, #99734 ) ; +#23344 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#23345 = SURFACE_STYLE_FILL_AREA ( #52991 ) ; +#23346 = ADVANCED_FACE ( 'NONE', ( #18214 ), #72364, .F. ) ; +#23348 = ADVANCED_FACE ( 'NONE', ( #50443 ), #73399, .T. ) ; +#23347 = SURFACE_STYLE_FILL_AREA ( #100804 ) ; +#23349 = LINE ( 'NONE', #79495, #4222 ) ; +#23350 = ORIENTED_EDGE ( 'NONE', *, *, #71167, .T. ) ; +#23352 = FILL_AREA_STYLE_COLOUR ( '', #89898 ) ; +#23351 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23353 = LINE ( 'NONE', #57540, #66111 ) ; +#23354 = PLANE ( 'NONE', #71536 ) ; +#23355 = STYLED_ITEM ( 'NONE', ( #48243 ), #19582 ) ; +#23356 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23357 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#23358 = VECTOR ( 'NONE', #50320, 1000.000000000000000 ) ; +#23359 = LINE ( 'NONE', #31510, #76097 ) ; +#23360 = EDGE_LOOP ( 'NONE', ( #53036, #18110, #99449, #98038 ) ) ; +#23361 = PRESENTATION_STYLE_ASSIGNMENT (( #77459 ) ) ; +#23362 = ADVANCED_FACE ( 'NONE', ( #66228 ), #96831, .T. ) ; +#23364 = STYLED_ITEM ( 'NONE', ( #41289 ), #18960 ) ; +#23363 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#23365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21676 ), #15140 ) ; +#23366 = LINE ( 'NONE', #100820, #70215 ) ; +#23367 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 6.776263578034399754E-16 ) ) ; +#23368 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75548 ) ) ; +#23369 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4600000000000000200, -0.2350000000000000144 ) ) ; +#23370 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#23371 = FILL_AREA_STYLE ('',( #87167 ) ) ; +#23372 = AXIS2_PLACEMENT_3D ( 'NONE', #14211, #76049, #22421 ) ; +#23373 = FILL_AREA_STYLE ('',( #22349 ) ) ; +#23374 = AXIS2_PLACEMENT_3D ( 'NONE', #33431, #64556, #65059 ) ; +#23375 = FILL_AREA_STYLE ('',( #58822 ) ) ; +#23376 = SURFACE_STYLE_USAGE ( .BOTH. , #86667 ) ; +#23377 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52757 ), #545 ) ; +#23378 = VERTEX_POINT ( 'NONE', #27953 ) ; +#23379 = SURFACE_SIDE_STYLE ('',( #44816 ) ) ; +#23380 = FACE_OUTER_BOUND ( 'NONE', #96428, .T. ) ; +#23381 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.3000000000000016542, -9.095983544939292593E-90 ) ) ; +#23382 = SURFACE_STYLE_FILL_AREA ( #77491 ) ; +#23383 = AXIS2_PLACEMENT_3D ( 'NONE', #90073, #50809, #89583 ) ; +#23384 = LINE ( 'NONE', #54549, #28009 ) ; +#23385 = SURFACE_STYLE_FILL_AREA ( #78016 ) ; +#23386 = FILL_AREA_STYLE_COLOUR ( '', #67247 ) ; +#23387 = SURFACE_STYLE_FILL_AREA ( #62710 ) ; +#23388 = ORIENTED_EDGE ( 'NONE', *, *, #1902, .F. ) ; +#23389 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#23390 = EDGE_CURVE ( 'NONE', #50319, #79914, #98297, .T. ) ; +#23391 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63723 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35040, #60412, #13844 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23392 = PRESENTATION_STYLE_ASSIGNMENT (( #22373 ) ) ; +#23393 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.900000000000000133, -1.507334416018511324E-89 ) ) ; +#23394 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#23395 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.05000000000000000278, 0.08229670385730990245 ) ) ; +#23396 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23521 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66109, #11885, #74271 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23397 = EDGE_CURVE ( 'NONE', #33415, #82922, #66713, .T. ) ; +#23398 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23399 = ORIENTED_EDGE ( 'NONE', *, *, #4729, .T. ) ; +#23400 = ORIENTED_EDGE ( 'NONE', *, *, #74510, .F. ) ; +#23401 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23402 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#23403 = VERTEX_POINT ( 'NONE', #51930 ) ; +#23404 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23405 = VECTOR ( 'NONE', #71349, 1000.000000000000000 ) ; +#23406 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #507 ), #49517 ) ; +#23407 = LINE ( 'NONE', #29552, #17259 ) ; +#23408 = FILL_AREA_STYLE_COLOUR ( '', #88707 ) ; +#23409 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #97758 ) ; +#23410 = LINE ( 'NONE', #44846, #41094 ) ; +#23411 = FILL_AREA_STYLE ('',( #14697 ) ) ; +#23414 = ORIENTED_EDGE ( 'NONE', *, *, #74677, .T. ) ; +#23413 = ORIENTED_EDGE ( 'NONE', *, *, #84849, .F. ) ; +#23412 = EDGE_CURVE ( 'NONE', #18845, #80960, #52929, .T. ) ; +#23415 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59318 ) ) ; +#23416 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#23417 = ORIENTED_EDGE ( 'NONE', *, *, #18841, .T. ) ; +#23419 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87758 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46952, #78603, #93390 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23418 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20180, 'distance_accuracy_value', 'NONE'); +#23420 = AXIS2_PLACEMENT_3D ( 'NONE', #51277, #82425, #4295 ) ; +#23421 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 9.092575000000000074, 0.8991599999999999593 ) ) ; +#23422 = SURFACE_STYLE_FILL_AREA ( #31074 ) ; +#23423 = VERTEX_POINT ( 'NONE', #83058 ) ; +#23424 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63550 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10971, #2911, #82033 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23425 = EDGE_CURVE ( 'NONE', #84214, #72489, #90713, .T. ) ; +#23426 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#23427 = FILL_AREA_STYLE_COLOUR ( '', #25240 ) ; +#23428 = STYLED_ITEM ( 'NONE', ( #5955 ), #19269 ) ; +#23429 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93498 ), #3819 ) ; +#23430 = LINE ( 'NONE', #947, #40600 ) ; +#23431 = FACE_OUTER_BOUND ( 'NONE', #80132, .T. ) ; +#23432 = EDGE_LOOP ( 'NONE', ( #8337, #37893, #65222, #43546 ) ) ; +#23433 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#23434 = VECTOR ( 'NONE', #79997, 1000.000000000000000 ) ; +#23435 = ORIENTED_EDGE ( 'NONE', *, *, #37736, .F. ) ; +#23436 = AXIS2_PLACEMENT_3D ( 'NONE', #87825, #48021, #26066 ) ; +#23437 = ORIENTED_EDGE ( 'NONE', *, *, #85664, .T. ) ; +#23438 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23440 = EDGE_CURVE ( 'NONE', #75401, #49085, #74396, .T. ) ; +#23442 = ORIENTED_EDGE ( 'NONE', *, *, #19058, .T. ) ; +#23441 = SURFACE_STYLE_FILL_AREA ( #78069 ) ; +#23443 = SURFACE_STYLE_FILL_AREA ( #30072 ) ; +#23444 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.723820061220085131, 0.000000000000000000 ) ) ; +#23445 = AXIS2_PLACEMENT_3D ( 'NONE', #21683, #100659, #39022 ) ; +#23446 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#23447 = VERTEX_POINT ( 'NONE', #75387 ) ; +#23449 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8648700000000000276 ) ) ; +#23448 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23450 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#23451 = ORIENTED_EDGE ( 'NONE', *, *, #77955, .T. ) ; +#23452 = ADVANCED_FACE ( 'NONE', ( #84060 ), #58603, .T. ) ; +#23453 = ORIENTED_EDGE ( 'NONE', *, *, #64106, .T. ) ; +#23455 = LINE ( 'NONE', #455, #89432 ) ; +#23454 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#23456 = CARTESIAN_POINT ( 'NONE', ( 1.784639205958740149, -1.415447185383410078, 0.8300000000000002931 ) ) ; +#23457 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64446 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11251, #94580, #12269 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23458 = FACE_OUTER_BOUND ( 'NONE', #53081, .T. ) ; +#23459 = VECTOR ( 'NONE', #32398, 1000.000000000000000 ) ; +#23460 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23461 = EDGE_CURVE ( 'NONE', #11187, #76842, #52423, .T. ) ; +#23463 = ADVANCED_FACE ( 'NONE', ( #13529 ), #27433, .T. ) ; +#23462 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000007994, -3.149999999999979927, 0.000000000000000000 ) ) ; +#23464 = FILL_AREA_STYLE_COLOUR ( '', #55285 ) ; +#23465 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27782, 'distance_accuracy_value', 'NONE'); +#23466 = CARTESIAN_POINT ( 'NONE', ( 0.2967604117379429862, -0.9084949572282049468, 0.8300000000000020695 ) ) ; +#23467 = ORIENTED_EDGE ( 'NONE', *, *, #9212, .F. ) ; +#23468 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#23469 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23470 = VERTEX_POINT ( 'NONE', #85049 ) ; +#23471 = FACE_OUTER_BOUND ( 'NONE', #2443, .T. ) ; +#23472 = EDGE_CURVE ( 'NONE', #29208, #24875, #24319, .T. ) ; +#23473 = EDGE_CURVE ( 'NONE', #100619, #54713, #15582, .T. ) ; +#23474 = FILL_AREA_STYLE ('',( #32144 ) ) ; +#23475 = SURFACE_SIDE_STYLE ('',( #38294 ) ) ; +#23476 = STYLED_ITEM ( 'NONE', ( #22657 ), #53246 ) ; +#23478 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#23477 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#23479 = CARTESIAN_POINT ( 'NONE', ( 1.799693084787389985, -1.050822088410799937, 0.8100000000000000533 ) ) ; +#23480 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23481 = PLANE ( 'NONE', #96792 ) ; +#23482 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#23483 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.09601199999999999, 0.8648700000000000276 ) ) ; +#23484 = ADVANCED_FACE ( 'NONE', ( #86571 ), #77381, .T. ) ; +#23485 = AXIS2_PLACEMENT_3D ( 'NONE', #86510, #40569, #62040 ) ; +#23486 = FILL_AREA_STYLE_COLOUR ( '', #93354 ) ; +#23487 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23488 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8648700000000000276 ) ) ; +#23489 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23490 = VECTOR ( 'NONE', #94558, 1000.000000000000000 ) ; +#23491 = STYLED_ITEM ( 'NONE', ( #60068 ), #26611 ) ; +#23492 = ADVANCED_FACE ( 'NONE', ( #70743 ), #53418, .T. ) ; +#23495 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23494 = LINE ( 'NONE', #67903, #12960 ) ; +#23493 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78941 ), #100035 ) ; +#23496 = SURFACE_SIDE_STYLE ('',( #100454 ) ) ; +#23497 = LINE ( 'NONE', #40838, #60078 ) ; +#23498 = SURFACE_STYLE_USAGE ( .BOTH. , #77097 ) ; +#23499 = LINE ( 'NONE', #86785, #31577 ) ; +#23500 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35985, #52304, #19632, #20623, #91573, #76252, #44587, #75760, #81946, #6248, #5770, #97688, #36967, #58982, #59491, #35487, #90583, #4314, #4796 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.320612373527808416E-05, 4.492052686938425860E-05, 6.582062287974220006E-05, 8.605494144860738575E-05, 0.0001059136079145855063, 0.0001256087639101565205, 0.0001452127442685341506, 0.0001650429405876124996, 0.0001850370302419250231, 0.0002052205854468231176, 0.0002258575965929248721, 0.0002469788263569267536, 0.0002682616920458915657, 0.0002891959060427917489, 0.0003100051045178301248, 0.0003307427320208264137 ), + .UNSPECIFIED. ) ; +#23501 = STYLED_ITEM ( 'NONE', ( #86143 ), #19958 ) ; +#23503 = ORIENTED_EDGE ( 'NONE', *, *, #92390, .T. ) ; +#23502 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#23504 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23505 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80778, 'distance_accuracy_value', 'NONE'); +#23506 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73475, 'distance_accuracy_value', 'NONE'); +#23507 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -2.914335439641030002E-16 ) ) ; +#23508 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#23509 = VECTOR ( 'NONE', #81411, 1000.000000000000000 ) ; +#23510 = CARTESIAN_POINT ( 'NONE', ( 0.4186776834897918409, -1.180776453863491504, 0.8100000000000001643 ) ) ; +#23511 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#23512 = LINE ( 'NONE', #99494, #37819 ) ; +#23514 = SURFACE_STYLE_USAGE ( .BOTH. , #62322 ) ; +#23513 = VECTOR ( 'NONE', #54369, 1000.000000000000114 ) ; +#23515 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23516 = ORIENTED_EDGE ( 'NONE', *, *, #56969, .F. ) ; +#23517 = SURFACE_STYLE_USAGE ( .BOTH. , #76118 ) ; +#23518 = ORIENTED_EDGE ( 'NONE', *, *, #66162, .F. ) ; +#23519 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23520 = EDGE_CURVE ( 'NONE', #55827, #62776, #12957, .T. ) ; +#23521 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66109, 'distance_accuracy_value', 'NONE'); +#23522 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26652, 'distance_accuracy_value', 'NONE'); +#23523 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999667, 0.1900000000000000022 ) ) ; +#23524 = PRESENTATION_STYLE_ASSIGNMENT (( #93414 ) ) ; +#23525 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#23526 = CARTESIAN_POINT ( 'NONE', ( -0.1192017212701950019, -1.445336647901249938, 0.8299999999999995159 ) ) ; +#23527 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10371 ) ) ; +#23528 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23529 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23530 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23531 = VERTEX_POINT ( 'NONE', #1823 ) ; +#23532 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, 1.100000000000000089 ) ) ; +#23533 = SURFACE_SIDE_STYLE ('',( #57086 ) ) ; +#23534 = CARTESIAN_POINT ( 'NONE', ( -1.970710678118650305, 1.529289321881339925, -0.02000000000000000042 ) ) ; +#23535 = ORIENTED_EDGE ( 'NONE', *, *, #4304, .T. ) ; +#23536 = PRESENTATION_STYLE_ASSIGNMENT (( #92915 ) ) ; +#23537 = PLANE ( 'NONE', #15813 ) ; +#23538 = VERTEX_POINT ( 'NONE', #63620 ) ; +#23539 = VECTOR ( 'NONE', #17133, 1000.000000000000000 ) ; +#23540 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#23541 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23542 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23543 = CARTESIAN_POINT ( 'NONE', ( 1.826762951391289969, -1.165682221622120096, 0.8100000000000000533 ) ) ; +#23544 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#23545 = CARTESIAN_POINT ( 'NONE', ( -0.4585056984953529424, 1.490568459948275359, 0.8100000000000002753 ) ) ; +#23548 = ORIENTED_EDGE ( 'NONE', *, *, #10324, .F. ) ; +#23547 = EDGE_LOOP ( 'NONE', ( #52256, #32749, #75789, #3606 ) ) ; +#23546 = VECTOR ( 'NONE', #99344, 1000.000000000000114 ) ; +#23549 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23550 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#23551 = ORIENTED_EDGE ( 'NONE', *, *, #49879, .T. ) ; +#23552 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#23553 = ORIENTED_EDGE ( 'NONE', *, *, #17588, .F. ) ; +#23555 = EDGE_CURVE ( 'NONE', #83700, #93723, #55960, .T. ) ; +#23554 = ORIENTED_EDGE ( 'NONE', *, *, #3240, .T. ) ; +#23556 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23557 = VECTOR ( 'NONE', #42458, 1000.000000000000000 ) ; +#23558 = SURFACE_STYLE_USAGE ( .BOTH. , #93454 ) ; +#23559 = EDGE_LOOP ( 'NONE', ( #42926, #47794, #66358, #82339, #14830, #7797 ) ) ; +#23560 = VERTEX_POINT ( 'NONE', #41133 ) ; +#23561 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70858 ) ) ; +#23562 = LINE ( 'NONE', #55233, #38742 ) ; +#23563 = VERTEX_POINT ( 'NONE', #48806 ) ; +#23564 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3947 ), #79029 ) ; +#23566 = ORIENTED_EDGE ( 'NONE', *, *, #93958, .T. ) ; +#23565 = LINE ( 'NONE', #54729, #67305 ) ; +#23567 = VECTOR ( 'NONE', #97399, 1000.000000000000000 ) ; +#23569 = FACE_OUTER_BOUND ( 'NONE', #23074, .T. ) ; +#23568 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23570 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23571 = VERTEX_POINT ( 'NONE', #50334 ) ; +#23572 = VECTOR ( 'NONE', #76222, 1000.000000000000000 ) ; +#23573 = FILL_AREA_STYLE ('',( #45997 ) ) ; +#23574 = VERTEX_POINT ( 'NONE', #2824 ) ; +#23575 = LINE ( 'NONE', #62391, #44841 ) ; +#23576 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51291 ) ) ; +#23577 = VECTOR ( 'NONE', #56551, 1000.000000000000000 ) ; +#23578 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.9000000000000014655, 8.225148568024281774E-79 ) ) ; +#23579 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23580 = ORIENTED_EDGE ( 'NONE', *, *, #56266, .F. ) ; +#23581 = AXIS2_PLACEMENT_3D ( 'NONE', #51581, #13155, #20899 ) ; +#23582 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#23583 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#23584 = PRESENTATION_STYLE_ASSIGNMENT (( #14858 ) ) ; +#23585 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8648700000000000276 ) ) ; +#23586 = SURFACE_STYLE_USAGE ( .BOTH. , #22060 ) ; +#23587 = ORIENTED_EDGE ( 'NONE', *, *, #4025, .T. ) ; +#23588 = STYLED_ITEM ( 'NONE', ( #93322 ), #3221 ) ; +#23589 = LINE ( 'NONE', #30713, #35298 ) ; +#23590 = SURFACE_SIDE_STYLE ('',( #62407 ) ) ; +#23591 = LINE ( 'NONE', #6673, #7648 ) ; +#23592 = LINE ( 'NONE', #63916, #25133 ) ; +#23593 = PLANE ( 'NONE', #42144 ) ; +#23594 = LINE ( 'NONE', #61912, #53212 ) ; +#23595 = VECTOR ( 'NONE', #60239, 1000.000000000000000 ) ; +#23596 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#23597 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23598 = ORIENTED_EDGE ( 'NONE', *, *, #71887, .T. ) ; +#23599 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67592 ) ) ; +#23600 = ADVANCED_FACE ( 'NONE', ( #56481 ), #48306, .T. ) ; +#23601 = ORIENTED_EDGE ( 'NONE', *, *, #67300, .F. ) ; +#23602 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23603 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12084 ), #56288 ) ; +#23604 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#23605 = PRESENTATION_STYLE_ASSIGNMENT (( #70047 ) ) ; +#23606 = SURFACE_STYLE_FILL_AREA ( #54254 ) ; +#23607 = AXIS2_PLACEMENT_3D ( 'NONE', #59724, #83668, #5497 ) ; +#23608 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2419 ), #69183 ) ; +#23609 = ORIENTED_EDGE ( 'NONE', *, *, #14983, .F. ) ; +#23610 = LINE ( 'NONE', #16928, #62053 ) ; +#23611 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #3736, #34909, #97137, #96133 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23612 = SURFACE_STYLE_FILL_AREA ( #32287 ) ; +#23613 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626903161, -0.1434314575050762430 ) ) ; +#23614 = FILL_AREA_STYLE_COLOUR ( '', #40024 ) ; +#23615 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#23616 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67608 ) ) ; +#23617 = FILL_AREA_STYLE ('',( #55294 ) ) ; +#23618 = PLANE ( 'NONE', #19228 ) ; +#23619 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23620 = FILL_AREA_STYLE_COLOUR ( '', #1830 ) ; +#23621 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.05000000000000002359, 0.2100000000000000200 ) ) ; +#23622 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#23623 = AXIS2_PLACEMENT_3D ( 'NONE', #14846, #52230, #53708 ) ; +#23624 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#23625 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23626 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69489, 'distance_accuracy_value', 'NONE'); +#23627 = EDGE_CURVE ( 'NONE', #24683, #84782, #56978, .T. ) ; +#23628 = FILL_AREA_STYLE_COLOUR ( '', #24088 ) ; +#23629 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10471 ) ) ; +#23630 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8648700000000000276 ) ) ; +#23631 = ORIENTED_EDGE ( 'NONE', *, *, #8887, .F. ) ; +#23632 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#23633 = ORIENTED_EDGE ( 'NONE', *, *, #58602, .F. ) ; +#23634 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46783, 'distance_accuracy_value', 'NONE'); +#23635 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17301, 'distance_accuracy_value', 'NONE'); +#23636 = FACE_OUTER_BOUND ( 'NONE', #56903, .T. ) ; +#23637 = SURFACE_SIDE_STYLE ('',( #71618 ) ) ; +#23638 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23639 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23640 = PRESENTATION_STYLE_ASSIGNMENT (( #62970 ) ) ; +#23641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98538 ), #36698 ) ; +#23642 = CARTESIAN_POINT ( 'NONE', ( 0.09335570779574380029, -1.336905478629369926, 0.8300000000000004041 ) ) ; +#23643 = CARTESIAN_POINT ( 'NONE', ( 0.06449442099368349335, -1.103202958186300320, 0.8100000000000000533 ) ) ; +#23644 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#23645 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23646 = EDGE_CURVE ( 'NONE', #76160, #25465, #40631, .T. ) ; +#23647 = EDGE_LOOP ( 'NONE', ( #98467, #97346, #59249, #57752 ) ) ; +#23648 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23649 = PRESENTATION_STYLE_ASSIGNMENT (( #78280 ) ) ; +#23650 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29130, 'distance_accuracy_value', 'NONE'); +#23651 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56340 ), #98546 ) ; +#23652 = ORIENTED_EDGE ( 'NONE', *, *, #77176, .T. ) ; +#23653 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#23654 = VECTOR ( 'NONE', #66556, 1000.000000000000000 ) ; +#23655 = ORIENTED_EDGE ( 'NONE', *, *, #95779, .T. ) ; +#23656 = FILL_AREA_STYLE ('',( #69581 ) ) ; +#23657 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23658 = SURFACE_STYLE_FILL_AREA ( #62477 ) ; +#23659 = PLANE ( 'NONE', #64163 ) ; +#23660 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999997335, -3.266666666666659946, 0.000000000000000000 ) ) ; +#23661 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85811, #92925, #31691, #23544 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23662 = LINE ( 'NONE', #94583, #4200 ) ; +#23663 = SURFACE_STYLE_USAGE ( .BOTH. , #14934 ) ; +#23664 = VERTEX_POINT ( 'NONE', #80959 ) ; +#23665 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77081 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89611, #33496, #65120 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23666 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#23667 = AXIS2_PLACEMENT_3D ( 'NONE', #9442, #34547, #94758 ) ; +#23668 = SURFACE_STYLE_FILL_AREA ( #9764 ) ; +#23669 = CARTESIAN_POINT ( 'NONE', ( 0.3586905243120019904, -0.9624267057659720015, 0.8300000000000002931 ) ) ; +#23671 = EDGE_CURVE ( 'NONE', #45112, #58869, #65597, .T. ) ; +#23670 = ORIENTED_EDGE ( 'NONE', *, *, #42717, .F. ) ; +#23672 = PRESENTATION_STYLE_ASSIGNMENT (( #69065 ) ) ; +#23673 = FACE_OUTER_BOUND ( 'NONE', #39340, .T. ) ; +#23674 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8199999999999999512 ) ) ; +#23675 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#23676 = FILL_AREA_STYLE_COLOUR ( '', #87495 ) ; +#23677 = ORIENTED_EDGE ( 'NONE', *, *, #2832, .T. ) ; +#23679 = ORIENTED_EDGE ( 'NONE', *, *, #12206, .F. ) ; +#23678 = VECTOR ( 'NONE', #34786, 1000.000000000000000 ) ; +#23680 = EDGE_CURVE ( 'NONE', #40536, #3712, #88576, .T. ) ; +#23681 = ORIENTED_EDGE ( 'NONE', *, *, #47734, .F. ) ; +#23682 = VECTOR ( 'NONE', #85131, 1000.000000000000000 ) ; +#23683 = ORIENTED_EDGE ( 'NONE', *, *, #84907, .F. ) ; +#23685 = ORIENTED_EDGE ( 'NONE', *, *, #80765, .T. ) ; +#23684 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#23686 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95543, #55785, #1132, #56815 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23687 = LINE ( 'NONE', #93075, #42565 ) ; +#23688 = SURFACE_SIDE_STYLE ('',( #14958 ) ) ; +#23690 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8100000000000068257 ) ) ; +#23689 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10530 ), #44855 ) ; +#23691 = CARTESIAN_POINT ( 'NONE', ( 3.383841999999999572, 7.565224999999999866, 0.8648700000000000276 ) ) ; +#23692 = ORIENTED_EDGE ( 'NONE', *, *, #48849, .F. ) ; +#23693 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#23694 = EDGE_LOOP ( 'NONE', ( #52023, #7109, #36998, #42964 ) ) ; +#23695 = EDGE_CURVE ( 'NONE', #14950, #9533, #80436, .T. ) ; +#23696 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23697 = EDGE_CURVE ( 'NONE', #93440, #59976, #10888, .T. ) ; +#23698 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23699 = VECTOR ( 'NONE', #96484, 1000.000000000000000 ) ; +#23700 = AXIS2_PLACEMENT_3D ( 'NONE', #49244, #27278, #33941 ) ; +#23701 = ORIENTED_EDGE ( 'NONE', *, *, #98234, .F. ) ; +#23704 = FILL_AREA_STYLE ('',( #78819 ) ) ; +#23703 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23702 = VECTOR ( 'NONE', #60510, 1000.000000000000000 ) ; +#23705 = CIRCLE ( 'NONE', #84047, 0.01000000000000002623 ) ; +#23706 = VERTEX_POINT ( 'NONE', #97222 ) ; +#23707 = VECTOR ( 'NONE', #51720, 1000.000000000000000 ) ; +#23708 = SURFACE_STYLE_USAGE ( .BOTH. , #72681 ) ; +#23709 = VECTOR ( 'NONE', #44862, 1000.000000000000000 ) ; +#23710 = LINE ( 'NONE', #92598, #8184 ) ; +#23711 = CARTESIAN_POINT ( 'NONE', ( 0.2039600559557959991, -1.343068553933169929, 0.8299999999999982947 ) ) ; +#23712 = EDGE_CURVE ( 'NONE', #18005, #94849, #83445, .T. ) ; +#23713 = ORIENTED_EDGE ( 'NONE', *, *, #84489, .T. ) ; +#23714 = PLANE ( 'NONE', #67814 ) ; +#23715 = ORIENTED_EDGE ( 'NONE', *, *, #98005, .F. ) ; +#23716 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#23717 = VECTOR ( 'NONE', #87683, 1000.000000000000000 ) ; +#23719 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23718 = FILL_AREA_STYLE ('',( #25257 ) ) ; +#23720 = PLANE ( 'NONE', #97489 ) ; +#23721 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#23723 = VECTOR ( 'NONE', #30100, 999.9999999999998863 ) ; +#23722 = VECTOR ( 'NONE', #54736, 1000.000000000000000 ) ; +#23724 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5999, 'distance_accuracy_value', 'NONE'); +#23725 = CARTESIAN_POINT ( 'NONE', ( -2.583333333333333481, 3.100000000000000533, 0.000000000000000000 ) ) ; +#23726 = SURFACE_STYLE_FILL_AREA ( #94119 ) ; +#23727 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23728 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23729 = SURFACE_STYLE_USAGE ( .BOTH. , #69647 ) ; +#23730 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23731 = FACE_OUTER_BOUND ( 'NONE', #88517, .T. ) ; +#23732 = ORIENTED_EDGE ( 'NONE', *, *, #63223, .T. ) ; +#23733 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822762999999999245, 0.8648700000000000276 ) ) ; +#23736 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#23735 = FACE_OUTER_BOUND ( 'NONE', #59496, .T. ) ; +#23734 = PRESENTATION_STYLE_ASSIGNMENT (( #93615 ) ) ; +#23737 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23738 = VECTOR ( 'NONE', #21057, 1000.000000000000000 ) ; +#23739 = PLANE ( 'NONE', #87729 ) ; +#23740 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23741 = CYLINDRICAL_SURFACE ( 'NONE', #84413, 1.383450513437169960 ) ; +#23742 = SURFACE_SIDE_STYLE ('',( #231 ) ) ; +#23743 = LINE ( 'NONE', #78367, #36406 ) ; +#23744 = EDGE_LOOP ( 'NONE', ( #98649, #56216, #67611, #99650 ) ) ; +#23745 = SURFACE_SIDE_STYLE ('',( #46691 ) ) ; +#23746 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23747 = FILL_AREA_STYLE_COLOUR ( '', #58343 ) ; +#23748 = AXIS2_PLACEMENT_3D ( 'NONE', #48045, #79709, #71531 ) ; +#23749 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#23750 = SURFACE_STYLE_USAGE ( .BOTH. , #93636 ) ; +#23751 = CYLINDRICAL_SURFACE ( 'NONE', #36075, 0.05000000000000012768 ) ; +#23752 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88985 ), #5768 ) ; +#23753 = SURFACE_SIDE_STYLE ('',( #16052 ) ) ; +#23754 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23755 = FILL_AREA_STYLE_COLOUR ( '', #76901 ) ; +#23756 = EDGE_CURVE ( 'NONE', #74262, #71529, #91094, .T. ) ; +#23757 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23758 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#23759 = LINE ( 'NONE', #71213, #60289 ) ; +#23760 = STYLED_ITEM ( 'NONE', ( #15239 ), #29894 ) ; +#23761 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23762 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23763 = ORIENTED_EDGE ( 'NONE', *, *, #40872, .F. ) ; +#23764 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26051, 'distance_accuracy_value', 'NONE'); +#23765 = PRESENTATION_STYLE_ASSIGNMENT (( #77871 ) ) ; +#23766 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23767 = VECTOR ( 'NONE', #25990, 1000.000000000000000 ) ; +#23768 = VECTOR ( 'NONE', #69951, 1000.000000000000000 ) ; +#23769 = SURFACE_SIDE_STYLE ('',( #53892 ) ) ; +#23770 = SURFACE_SIDE_STYLE ('',( #32938 ) ) ; +#23771 = LINE ( 'NONE', #8342, #27166 ) ; +#23772 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23773 = CARTESIAN_POINT ( 'NONE', ( -0.9584150915164789675, -1.224577966852969935, 0.8299999999999999600 ) ) ; +#23774 = ADVANCED_FACE ( 'NONE', ( #12904 ), #58991, .T. ) ; +#23775 = ORIENTED_EDGE ( 'NONE', *, *, #22902, .T. ) ; +#23776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54771 ) ) ; +#23777 = SURFACE_SIDE_STYLE ('',( #61584 ) ) ; +#23778 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95844, 'distance_accuracy_value', 'NONE'); +#23779 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23781 = FILL_AREA_STYLE ('',( #15563 ) ) ; +#23780 = VECTOR ( 'NONE', #85891, 1000.000000000000000 ) ; +#23782 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#23783 = VECTOR ( 'NONE', #89260, 1000.000000000000000 ) ; +#23784 = ORIENTED_EDGE ( 'NONE', *, *, #37524, .T. ) ; +#23785 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#23786 = LINE ( 'NONE', #86049, #51710 ) ; +#23787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69428 ) ) ; +#23789 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7500000000000002220, -0.6999999999859481958 ) ) ; +#23790 = LINE ( 'NONE', #39593, #32706 ) ; +#23791 = LINE ( 'NONE', #46729, #13589 ) ; +#23792 = ORIENTED_EDGE ( 'NONE', *, *, #24417, .T. ) ; +#23793 = FACE_OUTER_BOUND ( 'NONE', #9274, .T. ) ; +#23794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52189, 'distance_accuracy_value', 'NONE'); +#23795 = FILL_AREA_STYLE ('',( #49287 ) ) ; +#23796 = AXIS2_PLACEMENT_3D ( 'NONE', #24171, #57846, #97074 ) ; +#23797 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23798 = VERTEX_POINT ( 'NONE', #44123 ) ; +#23799 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40290, #31097, #62768 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23800 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4519 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62319, #37818, #53641 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23801 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#23802 = FACE_OUTER_BOUND ( 'NONE', #49456, .T. ) ; +#23803 = ORIENTED_EDGE ( 'NONE', *, *, #38998, .T. ) ; +#23804 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#23805 = CARTESIAN_POINT ( 'NONE', ( 0.05811896311769199769, -1.438073744133560039, 0.8299999999999999600 ) ) ; +#23806 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.000000000000000000 ) ) ; +#23807 = FILL_AREA_STYLE_COLOUR ( '', #67761 ) ; +#23808 = EDGE_CURVE ( 'NONE', #95720, #98852, #90595, .T. ) ; +#23809 = VECTOR ( 'NONE', #67851, 1000.000000000000000 ) ; +#23810 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23811 = ORIENTED_EDGE ( 'NONE', *, *, #23021, .F. ) ; +#23812 = FILL_AREA_STYLE ('',( #1318 ) ) ; +#23813 = DIRECTION ( 'NONE', ( -1.000000000000000000, -9.346570452461245291E-17, -9.059419880941277370E-14 ) ) ; +#23815 = FILL_AREA_STYLE_COLOUR ( '', #95264 ) ; +#23814 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23816 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.300000000000000044, -0.02000000000000000042 ) ) ; +#23817 = ORIENTED_EDGE ( 'NONE', *, *, #64964, .T. ) ; +#23818 = EDGE_CURVE ( 'NONE', #53594, #76167, #98177, .T. ) ; +#23819 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23820 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23821 = EDGE_CURVE ( 'NONE', #61734, #60413, #89595, .T. ) ; +#23822 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#23823 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#23824 = ORIENTED_EDGE ( 'NONE', *, *, #40364, .T. ) ; +#23825 = AXIS2_PLACEMENT_3D ( 'NONE', #91742, #36665, #30448 ) ; +#23826 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23827 = ORIENTED_EDGE ( 'NONE', *, *, #67259, .F. ) ; +#23828 = VERTEX_POINT ( 'NONE', #35995 ) ; +#23829 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#23830 = SURFACE_STYLE_USAGE ( .BOTH. , #86601 ) ; +#23831 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23832 = FILL_AREA_STYLE ('',( #86604 ) ) ; +#23833 = VERTEX_POINT ( 'NONE', #75283 ) ; +#23834 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#23835 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23836 = EDGE_CURVE ( 'NONE', #76885, #88653, #4529, .T. ) ; +#23837 = PRESENTATION_STYLE_ASSIGNMENT (( #838 ) ) ; +#23838 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87377 ), #74341 ) ; +#23839 = AXIS2_PLACEMENT_3D ( 'NONE', #71695, #87511, #32395 ) ; +#23840 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -3.500000000000000444, 1.308546363094771468E-78 ) ) ; +#23841 = VECTOR ( 'NONE', #94902, 1000.000000000000000 ) ; +#23842 = ORIENTED_EDGE ( 'NONE', *, *, #80401, .F. ) ; +#23844 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#23843 = PLANE ( 'NONE', #100294 ) ; +#23845 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23846 = ORIENTED_EDGE ( 'NONE', *, *, #70666, .T. ) ; +#23847 = ORIENTED_EDGE ( 'NONE', *, *, #23390, .F. ) ; +#23848 = PRESENTATION_STYLE_ASSIGNMENT (( #27621 ) ) ; +#23849 = CARTESIAN_POINT ( 'NONE', ( 1.198411601801520066, -1.515412412365080064, 0.8100000000000000533 ) ) ; +#23850 = FACE_OUTER_BOUND ( 'NONE', #93411, .T. ) ; +#23851 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#23852 = STYLED_ITEM ( 'NONE', ( #63918 ), #61685 ) ; +#23853 = FILL_AREA_STYLE_COLOUR ( '', #5827 ) ; +#23855 = EDGE_CURVE ( 'NONE', #20312, #9359, #67100, .T. ) ; +#23854 = FACE_OUTER_BOUND ( 'NONE', #75393, .T. ) ; +#23856 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85116, #69781, #30996, #93247 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#23857 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#23858 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23859 = VECTOR ( 'NONE', #92795, 1000.000000000000000 ) ; +#23860 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.05000000000000000278, 0.08229670385730990245 ) ) ; +#23861 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100957 ) ; +#23862 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23863 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#23864 = SURFACE_SIDE_STYLE ('',( #7924 ) ) ; +#23865 = EDGE_CURVE ( 'NONE', #92789, #91124, #47215, .T. ) ; +#23866 = VERTEX_POINT ( 'NONE', #37491 ) ; +#23867 = STYLED_ITEM ( 'NONE', ( #5914 ), #77770 ) ; +#23868 = EDGE_CURVE ( 'NONE', #35632, #48127, #71005, .T. ) ; +#23869 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23871 = SURFACE_STYLE_USAGE ( .BOTH. , #93246 ) ; +#23870 = SURFACE_STYLE_FILL_AREA ( #8427 ) ; +#23872 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#23873 = ADVANCED_FACE ( 'NONE', ( #86318 ), #71518, .T. ) ; +#23874 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#23875 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23876 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#23877 = PLANE ( 'NONE', #33048 ) ; +#23878 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #46631 ) ) ; +#23879 = ORIENTED_EDGE ( 'NONE', *, *, #100717, .F. ) ; +#23880 = SURFACE_STYLE_FILL_AREA ( #56547 ) ; +#23881 = FILL_AREA_STYLE_COLOUR ( '', #17906 ) ; +#23882 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23883 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#23884 = PLANE ( 'NONE', #39901 ) ; +#23885 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23952, 'distance_accuracy_value', 'NONE'); +#23886 = STYLED_ITEM ( 'NONE', ( #82664 ), #4990 ) ; +#23887 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23888 = FACE_OUTER_BOUND ( 'NONE', #71140, .T. ) ; +#23889 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23890 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23891 = VECTOR ( 'NONE', #66133, 1000.000000000000000 ) ; +#23892 = SURFACE_STYLE_USAGE ( .BOTH. , #40720 ) ; +#23893 = ADVANCED_FACE ( 'NONE', ( #94468 ), #1056, .F. ) ; +#23894 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23895 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, 0.6500000000000000222 ) ) ; +#23896 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000172, 0.8991599999999999593 ) ) ; +#23897 = STYLED_ITEM ( 'NONE', ( #18132 ), #4114 ) ; +#23898 = VECTOR ( 'NONE', #79308, 1000.000000000000000 ) ; +#23899 = LINE ( 'NONE', #891, #30753 ) ; +#23900 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #75595, 'design' ) ; +#23901 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 2.877107000000000081, 0.8648700000000000276 ) ) ; +#23902 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#23903 = EDGE_CURVE ( 'NONE', #79701, #51041, #9142, .T. ) ; +#23904 = VERTEX_POINT ( 'NONE', #79177 ) ; +#23905 = CARTESIAN_POINT ( 'NONE', ( -0.3685250336285872952, -1.197960699744545776, 0.8099999999999907274 ) ) ; +#23906 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23907 = CARTESIAN_POINT ( 'NONE', ( 1.639423674598250003, -1.436594792639700024, 0.8299999999999977396 ) ) ; +#23908 = LINE ( 'NONE', #65712, #88501 ) ; +#23909 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2126, 'distance_accuracy_value', 'NONE'); +#23910 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077921386, 0.7099999999999999645, -4.598363044682736897E-18 ) ) ; +#23911 = EDGE_CURVE ( 'NONE', #5265, #89499, #72027, .T. ) ; +#23912 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67875 ) ) ; +#23913 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#23914 = CARTESIAN_POINT ( 'NONE', ( 1.134237183092902557, -1.136068795193197145, 0.8099999999999039080 ) ) ; +#23915 = SURFACE_STYLE_FILL_AREA ( #15167 ) ; +#23916 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#23917 = STYLED_ITEM ( 'NONE', ( #56013 ), #30164 ) ; +#23918 = ORIENTED_EDGE ( 'NONE', *, *, #27106, .F. ) ; +#23919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23920 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#23921 = CARTESIAN_POINT ( 'NONE', ( 1.769821822789199972, -1.235192314287260062, 0.8299999999999994049 ) ) ; +#23922 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41122, 'distance_accuracy_value', 'NONE'); +#23924 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#23923 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28769 ) ) ; +#23925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16814, 'distance_accuracy_value', 'NONE'); +#23926 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23927 = SURFACE_SIDE_STYLE ('',( #16201 ) ) ; +#23928 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17399 ) ) ; +#23929 = ORIENTED_EDGE ( 'NONE', *, *, #29571, .T. ) ; +#23931 = ORIENTED_EDGE ( 'NONE', *, *, #26684, .F. ) ; +#23930 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17327 ), #77686 ) ; +#23932 = LINE ( 'NONE', #46348, #6264 ) ; +#23933 = VERTEX_POINT ( 'NONE', #94961 ) ; +#23934 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#23935 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23936 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23937 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#23938 = EDGE_CURVE ( 'NONE', #37511, #57348, #56217, .T. ) ; +#23939 = ADVANCED_FACE ( 'NONE', ( #27584 ), #65874, .T. ) ; +#23940 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16932, 'distance_accuracy_value', 'NONE'); +#23941 = SURFACE_STYLE_FILL_AREA ( #92796 ) ; +#23942 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100366 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25445, #57609, #65226 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23943 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #12294 ) ; +#23944 = FILL_AREA_STYLE ('',( #38726 ) ) ; +#23945 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23947 = ORIENTED_EDGE ( 'NONE', *, *, #89084, .F. ) ; +#23946 = ORIENTED_EDGE ( 'NONE', *, *, #7680, .T. ) ; +#23948 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21402 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100816, #38663, #45784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23949 = ORIENTED_EDGE ( 'NONE', *, *, #23107, .T. ) ; +#23950 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74522 ) ) ; +#23951 = VECTOR ( 'NONE', #48792, 1000.000000000000000 ) ; +#23952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23954 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#23953 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#23955 = VERTEX_POINT ( 'NONE', #42396 ) ; +#23956 = CLOSED_SHELL ( 'NONE', ( #25929, #50559, #4429, #50685, #5290, #65026 ) ) ; +#23958 = CIRCLE ( 'NONE', #81029, 0.6999999999999999556 ) ; +#23957 = SURFACE_STYLE_USAGE ( .BOTH. , #31582 ) ; +#23959 = FILL_AREA_STYLE ('',( #68363 ) ) ; +#23960 = EDGE_CURVE ( 'NONE', #97934, #53854, #17870, .T. ) ; +#23961 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#23962 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999985359, 0.1400000000000000133 ) ) ; +#23963 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#23964 = ORIENTED_EDGE ( 'NONE', *, *, #81329, .T. ) ; +#23965 = EDGE_CURVE ( 'NONE', #79538, #41134, #34247, .T. ) ; +#23966 = LINE ( 'NONE', #2975, #30780 ) ; +#23967 = ORIENTED_EDGE ( 'NONE', *, *, #22013, .F. ) ; +#23968 = VERTEX_POINT ( 'NONE', #26075 ) ; +#23969 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35354 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12817, #26728, #26226 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#23970 = LINE ( 'NONE', #78065, #26604 ) ; +#23971 = SURFACE_STYLE_FILL_AREA ( #100891 ) ; +#23972 = STYLED_ITEM ( 'NONE', ( #42048 ), #4509 ) ; +#23973 = SURFACE_SIDE_STYLE ('',( #78068 ) ) ; +#23975 = ORIENTED_EDGE ( 'NONE', *, *, #24074, .F. ) ; +#23974 = SURFACE_SIDE_STYLE ('',( #80603 ) ) ; +#23976 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.300000000000000266, 0.000000000000000000 ) ) ; +#23977 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87578 ) ) ; +#23978 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#23979 = DIRECTION ( 'NONE', ( -9.922965125553800473E-95, 2.143355994988570127E-63, 1.000000000000000000 ) ) ; +#23980 = ORIENTED_EDGE ( 'NONE', *, *, #23836, .T. ) ; +#23982 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23981 = FILL_AREA_STYLE ('',( #93841 ) ) ; +#23983 = ORIENTED_EDGE ( 'NONE', *, *, #12736, .T. ) ; +#23984 = ORIENTED_EDGE ( 'NONE', *, *, #91799, .T. ) ; +#23985 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#23986 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#23987 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#23988 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56577 ), #51684 ) ; +#23989 = PLANE ( 'NONE', #3755 ) ; +#23990 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#23991 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.549999999999999822, 0.000000000000000000 ) ) ; +#23992 = ORIENTED_EDGE ( 'NONE', *, *, #99772, .F. ) ; +#23993 = CARTESIAN_POINT ( 'NONE', ( 0.09190937866851861537, -1.304291937284929981, 0.8299999999999999600 ) ) ; +#23994 = EDGE_LOOP ( 'NONE', ( #4431, #73913, #31273, #82221 ) ) ; +#23995 = EDGE_CURVE ( 'NONE', #21356, #97123, #19394, .T. ) ; +#23996 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#23997 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#23998 = PRESENTATION_STYLE_ASSIGNMENT (( #8046 ) ) ; +#23999 = STYLED_ITEM ( 'NONE', ( #91528 ), #90639 ) ; +#24000 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31579, #76524, #55601, #47401 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24002 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#24001 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2808578643762690286, -0.1399999999999999856 ) ) ; +#24003 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24004 = FACE_OUTER_BOUND ( 'NONE', #42212, .T. ) ; +#24005 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8873, 'distance_accuracy_value', 'NONE'); +#24006 = SURFACE_SIDE_STYLE ('',( #93863 ) ) ; +#24007 = PRESENTATION_STYLE_ASSIGNMENT (( #61797 ) ) ; +#24008 = FILL_AREA_STYLE ('',( #32154 ) ) ; +#24009 = LINE ( 'NONE', #23488, #37024 ) ; +#24010 = STYLED_ITEM ( 'NONE', ( #7163 ), #79151 ) ; +#24011 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24012 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46766 ) ) ; +#24013 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24014 = LINE ( 'NONE', #55167, #28948 ) ; +#24015 = VECTOR ( 'NONE', #50816, 1000.000000000000114 ) ; +#24016 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20701 ), #81088 ) ; +#24018 = SURFACE_STYLE_USAGE ( .BOTH. , #84755 ) ; +#24019 = PLANE ( 'NONE', #75597 ) ; +#24020 = VECTOR ( 'NONE', #18701, 1000.000000000000000 ) ; +#24021 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84426, 'distance_accuracy_value', 'NONE'); +#24022 = ORIENTED_EDGE ( 'NONE', *, *, #20230, .F. ) ; +#24023 = CLOSED_SHELL ( 'NONE', ( #15691, #27226, #89323, #98674, #10436, #33802 ) ) ; +#24024 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24025 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24026 = ADVANCED_FACE ( 'NONE', ( #81209 ), #96471, .T. ) ; +#24027 = ORIENTED_EDGE ( 'NONE', *, *, #54475, .T. ) ; +#24028 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24029 = VECTOR ( 'NONE', #35063, 1000.000000000000000 ) ; +#24030 = DIRECTION ( 'NONE', ( 0.000000000000000000, -9.486769009248140132E-16, -1.000000000000000000 ) ) ; +#24031 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#24032 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24033 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8100000000000271427 ) ) ; +#24034 = VECTOR ( 'NONE', #8607, 1000.000000000000000 ) ; +#24035 = VERTEX_POINT ( 'NONE', #46696 ) ; +#24036 = SURFACE_STYLE_FILL_AREA ( #86805 ) ; +#24037 = ORIENTED_EDGE ( 'NONE', *, *, #3159, .T. ) ; +#24038 = FACE_OUTER_BOUND ( 'NONE', #6432, .T. ) ; +#24039 = ADVANCED_FACE ( 'NONE', ( #40588 ), #1256, .T. ) ; +#24040 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#24041 = FILL_AREA_STYLE_COLOUR ( '', #99370 ) ; +#24042 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24043 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#24044 = EDGE_CURVE ( 'NONE', #91833, #44546, #63068, .T. ) ; +#24045 = ORIENTED_EDGE ( 'NONE', *, *, #50708, .F. ) ; +#24046 = CARTESIAN_POINT ( 'NONE', ( 0.9002637987012989118, 0.6899999999999999467, 3.252606517456513302E-16 ) ) ; +#24047 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#24048 = ORIENTED_EDGE ( 'NONE', *, *, #26234, .T. ) ; +#24049 = STYLED_ITEM ( 'NONE', ( #24697 ), #57427 ) ; +#24050 = EDGE_LOOP ( 'NONE', ( #35962, #40006, #95859, #77174 ) ) ; +#24051 = LINE ( 'NONE', #32710, #8016 ) ; +#24052 = CARTESIAN_POINT ( 'NONE', ( 1.205759526989409913, -1.445368494507049961, 0.8299999999999999600 ) ) ; +#24053 = EDGE_CURVE ( 'NONE', #4760, #19800, #24271, .T. ) ; +#24054 = EDGE_CURVE ( 'NONE', #81624, #10757, #79382, .T. ) ; +#24055 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#24056 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24057 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95717 ) ) ; +#24058 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24059 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24060 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8991599999999999593 ) ) ; +#24062 = VERTEX_POINT ( 'NONE', #94663 ) ; +#24061 = EDGE_LOOP ( 'NONE', ( #15177, #91153, #29625, #66704 ) ) ; +#24063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24064 = EDGE_CURVE ( 'NONE', #72400, #91487, #52130, .T. ) ; +#24065 = EDGE_CURVE ( 'NONE', #10257, #86336, #86016, .T. ) ; +#24066 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#24067 = ORIENTED_EDGE ( 'NONE', *, *, #64602, .T. ) ; +#24069 = SURFACE_STYLE_USAGE ( .BOTH. , #48041 ) ; +#24068 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#24070 = ORIENTED_EDGE ( 'NONE', *, *, #66950, .T. ) ; +#24071 = ORIENTED_EDGE ( 'NONE', *, *, #16945, .T. ) ; +#24072 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24073 = PLANE ( 'NONE', #23748 ) ; +#24074 = EDGE_CURVE ( 'NONE', #32855, #57348, #56433, .T. ) ; +#24075 = CARTESIAN_POINT ( 'NONE', ( -0.1737436406883610396, -0.9784189978443861291, 0.8300000000000000711 ) ) ; +#24076 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53426 ), #90891 ) ; +#24077 = PLANE ( 'NONE', #64760 ) ; +#24078 = LINE ( 'NONE', #92461, #40005 ) ; +#24079 = ORIENTED_EDGE ( 'NONE', *, *, #79463, .T. ) ; +#24080 = ORIENTED_EDGE ( 'NONE', *, *, #45224, .F. ) ; +#24081 = SURFACE_STYLE_FILL_AREA ( #38876 ) ; +#24082 = VERTEX_POINT ( 'NONE', #87536 ) ; +#24083 = EDGE_CURVE ( 'NONE', #74570, #91599, #48250, .T. ) ; +#24084 = VECTOR ( 'NONE', #76412, 1000.000000000000000 ) ; +#24085 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68049 ), #50194 ) ; +#24086 = AXIS2_PLACEMENT_3D ( 'NONE', #76098, #6083, #66927 ) ; +#24087 = ORIENTED_EDGE ( 'NONE', *, *, #94985, .F. ) ; +#24088 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24089 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84172 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28074, #45340, #91821 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24090 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24091 = CARTESIAN_POINT ( 'NONE', ( 1.755956893679319952, -1.501723168847330259, 0.8099999999999996092 ) ) ; +#24092 = VERTEX_POINT ( 'NONE', #93131 ) ; +#24093 = CLOSED_SHELL ( 'NONE', ( #72168, #90418, #45734, #18648, #2864, #70792 ) ) ; +#24094 = PRESENTATION_STYLE_ASSIGNMENT (( #54740 ) ) ; +#24095 = ORIENTED_EDGE ( 'NONE', *, *, #80052, .T. ) ; +#24096 = VECTOR ( 'NONE', #38314, 1000.000000000000000 ) ; +#24097 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64809 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95766, #73343, #57536 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24098 = SURFACE_SIDE_STYLE ('',( #17402 ) ) ; +#24099 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24100 = VERTEX_POINT ( 'NONE', #23250 ) ; +#24102 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24101 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72995 ), #7727 ) ; +#24103 = PLANE ( 'NONE', #60256 ) ; +#24105 = CARTESIAN_POINT ( 'NONE', ( 1.549081571661369949, -1.457888621141530061, 0.8100000000000000533 ) ) ; +#24104 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#24106 = PRESENTATION_STYLE_ASSIGNMENT (( #80620 ) ) ; +#24107 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#24108 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2959 ), #89322 ) ; +#24109 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24110 = VERTEX_POINT ( 'NONE', #54910 ) ; +#24111 = EDGE_CURVE ( 'NONE', #19133, #16240, #242, .T. ) ; +#24112 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.000000000000000000 ) ) ; +#24113 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8648700000000000276 ) ) ; +#24114 = CARTESIAN_POINT ( 'NONE', ( -0.3116078311044310212, -1.336216925617480067, 0.8299999999999999600 ) ) ; +#24115 = LINE ( 'NONE', #9695, #56165 ) ; +#24116 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2399999999999999634 ) ) ; +#24117 = EDGE_CURVE ( 'NONE', #78971, #71387, #93635, .T. ) ; +#24119 = CARTESIAN_POINT ( 'NONE', ( 1.566818635346699962, -1.328064047174219997, 0.8100000000000000533 ) ) ; +#24118 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24120 = PLANE ( 'NONE', #76365 ) ; +#24121 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.100000000000000089, 0.000000000000000000 ) ) ; +#24122 = SURFACE_SIDE_STYLE ('',( #33796 ) ) ; +#24123 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24124 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24125 = ORIENTED_EDGE ( 'NONE', *, *, #91293, .F. ) ; +#24126 = SURFACE_STYLE_USAGE ( .BOTH. , #55273 ) ; +#24127 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24128 = ORIENTED_EDGE ( 'NONE', *, *, #83416, .F. ) ; +#24129 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46892 ) ) ; +#24130 = LINE ( 'NONE', #70556, #27600 ) ; +#24132 = SURFACE_STYLE_USAGE ( .BOTH. , #49119 ) ; +#24131 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#24133 = PRESENTATION_STYLE_ASSIGNMENT (( #14387 ) ) ; +#24134 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24135 = AXIS2_PLACEMENT_3D ( 'NONE', #71202, #9345, #1255 ) ; +#24136 = SURFACE_STYLE_USAGE ( .BOTH. , #86912 ) ; +#24137 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100069, #7168, #91018, #29239 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24138 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42935, 'distance_accuracy_value', 'NONE'); +#24139 = ORIENTED_EDGE ( 'NONE', *, *, #57309, .F. ) ; +#24140 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#24141 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68109 ), #20838 ) ; +#24142 = EDGE_CURVE ( 'NONE', #44133, #59792, #69672, .T. ) ; +#24143 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24144 = SURFACE_SIDE_STYLE ('',( #61931 ) ) ; +#24145 = SURFACE_STYLE_FILL_AREA ( #24657 ) ; +#24146 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24147 = FILL_AREA_STYLE ('',( #62437 ) ) ; +#24148 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24149 = CIRCLE ( 'NONE', #99018, 0.1999999999999996503 ) ; +#24150 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#24151 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#24152 = CARTESIAN_POINT ( 'NONE', ( 0.05660856691479519698, -0.9907810524907130212, 0.8299999999999999600 ) ) ; +#24153 = STYLED_ITEM ( 'NONE', ( #73060 ), #17457 ) ; +#24154 = FACE_OUTER_BOUND ( 'NONE', #50145, .T. ) ; +#24155 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24156 = LINE ( 'NONE', #9227, #6349 ) ; +#24157 = VERTEX_POINT ( 'NONE', #39063 ) ; +#24158 = ORIENTED_EDGE ( 'NONE', *, *, #27749, .T. ) ; +#24160 = AXIS2_PLACEMENT_3D ( 'NONE', #91929, #59843, #29161 ) ; +#24159 = PLANE ( 'NONE', #70984 ) ; +#24162 = STYLED_ITEM ( 'NONE', ( #96340 ), #16730 ) ; +#24161 = FILL_AREA_STYLE_COLOUR ( '', #78673 ) ; +#24163 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.35000000000000142 ) ) ; +#24164 = CARTESIAN_POINT ( 'NONE', ( 0.08972571571753010233, -1.370875895369189967, 0.8300000000000004041 ) ) ; +#24165 = STYLED_ITEM ( 'NONE', ( #56069 ), #23362 ) ; +#24166 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24167 = FILL_AREA_STYLE_COLOUR ( '', #24938 ) ; +#24168 = CLOSED_SHELL ( 'NONE', ( #98042, #59954, #13320, #65588, #53246, #1654 ) ) ; +#24169 = EDGE_LOOP ( 'NONE', ( #50488, #41394, #29545, #15457 ) ) ; +#24170 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24171 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 12.65647100000000158, 0.8991599999999999593 ) ) ; +#24172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24173 = AXIS2_PLACEMENT_3D ( 'NONE', #33163, #64303, #64801 ) ; +#24174 = SURFACE_SIDE_STYLE ('',( #30775 ) ) ; +#24175 = ORIENTED_EDGE ( 'NONE', *, *, #75962, .T. ) ; +#24176 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#24177 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24178 = ORIENTED_EDGE ( 'NONE', *, *, #27887, .T. ) ; +#24179 = PRESENTATION_STYLE_ASSIGNMENT (( #77769 ) ) ; +#24180 = AXIS2_PLACEMENT_3D ( 'NONE', #92769, #37208, #24408 ) ; +#24181 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#24182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38879 ), #50294 ) ; +#24183 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24184 = SURFACE_STYLE_USAGE ( .BOTH. , #62989 ) ; +#24185 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#24186 = VERTEX_POINT ( 'NONE', #64560 ) ; +#24187 = FACE_OUTER_BOUND ( 'NONE', #12683, .T. ) ; +#24188 = EDGE_CURVE ( 'NONE', #52114, #47399, #80910, .T. ) ; +#24189 = FILL_AREA_STYLE_COLOUR ( '', #49586 ) ; +#24190 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24191 = SURFACE_STYLE_USAGE ( .BOTH. , #86452 ) ; +#24192 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66583 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71162, #48202, #1205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24193 = VERTEX_POINT ( 'NONE', #50779 ) ; +#24194 = LINE ( 'NONE', #47139, #49792 ) ; +#24195 = EDGE_CURVE ( 'NONE', #36490, #57623, #95667, .T. ) ; +#24196 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #67765, .NOT_KNOWN. ) ; +#24197 = FACE_OUTER_BOUND ( 'NONE', #90743, .T. ) ; +#24198 = PLANE ( 'NONE', #68179 ) ; +#24199 = VECTOR ( 'NONE', #81431, 1000.000000000000000 ) ; +#24200 = PLANE ( 'NONE', #83566 ) ; +#24201 = AXIS2_PLACEMENT_3D ( 'NONE', #72044, #65364, #26589 ) ; +#24202 = VERTEX_POINT ( 'NONE', #42089 ) ; +#24203 = EDGE_LOOP ( 'NONE', ( #97073, #88303, #32708, #13845 ) ) ; +#24204 = ORIENTED_EDGE ( 'NONE', *, *, #36961, .T. ) ; +#24205 = EDGE_CURVE ( 'NONE', #82566, #39700, #19081, .T. ) ; +#24206 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24207 = ORIENTED_EDGE ( 'NONE', *, *, #88249, .T. ) ; +#24208 = STYLED_ITEM ( 'NONE', ( #43005 ), #56362 ) ; +#24210 = ORIENTED_EDGE ( 'NONE', *, *, #23960, .F. ) ; +#24209 = FILL_AREA_STYLE ('',( #23179 ) ) ; +#24211 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24212 = VECTOR ( 'NONE', #40464, 999.9999999999998863 ) ; +#24213 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8648700000000000276 ) ) ; +#24214 = PLANE ( 'NONE', #30252 ) ; +#24215 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#24216 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#24217 = ORIENTED_EDGE ( 'NONE', *, *, #1468, .T. ) ; +#24218 = CARTESIAN_POINT ( 'NONE', ( 1.731329805614240325, -1.441250752426249893, 0.8099999999999997202 ) ) ; +#24219 = CARTESIAN_POINT ( 'NONE', ( -1.476179938779914602, -3.099999999999990319, 0.000000000000000000 ) ) ; +#24220 = VERTEX_POINT ( 'NONE', #57424 ) ; +#24221 = VECTOR ( 'NONE', #41732, 1000.000000000000000 ) ; +#24222 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68899, #6577, #32153, #71454 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24223 = PLANE ( 'NONE', #82290 ) ; +#24224 = SURFACE_STYLE_FILL_AREA ( #48198 ) ; +#24225 = VERTEX_POINT ( 'NONE', #97175 ) ; +#24226 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46997 ) ) ; +#24227 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.6600000000000000311, 0.8000000000000003775 ) ) ; +#24228 = ORIENTED_EDGE ( 'NONE', *, *, #87997, .T. ) ; +#24229 = VECTOR ( 'NONE', #6048, 1000.000000000000000 ) ; +#24230 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24231 = SURFACE_STYLE_FILL_AREA ( #18018 ) ; +#24232 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56817 ), #22592 ) ; +#24233 = STYLED_ITEM ( 'NONE', ( #43699 ), #62848 ) ; +#24234 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#24235 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24236 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76377 ) ) ; +#24238 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55219 ), #94051 ) ; +#24237 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#24239 = EDGE_LOOP ( 'NONE', ( #93291, #19924, #56426, #54488 ) ) ; +#24240 = STYLED_ITEM ( 'NONE', ( #7652 ), #235 ) ; +#24241 = EDGE_CURVE ( 'NONE', #3583, #88355, #87362, .T. ) ; +#24242 = SURFACE_STYLE_FILL_AREA ( #41559 ) ; +#24243 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24244 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.000000000000000000 ) ) ; +#24245 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8648700000000000276 ) ) ; +#24246 = PRESENTATION_STYLE_ASSIGNMENT (( #86508 ) ) ; +#24247 = FACE_OUTER_BOUND ( 'NONE', #39977, .T. ) ; +#24248 = LINE ( 'NONE', #24765, #96579 ) ; +#24249 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22617 ), #42177 ) ; +#24250 = DIRECTION ( 'NONE', ( 0.7071067811865504593, 0.7071067811865445751, 0.000000000000000000 ) ) ; +#24251 = VERTEX_POINT ( 'NONE', #88045 ) ; +#24252 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24253 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 3.676137000000000210, 0.8648700000000000276 ) ) ; +#24255 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24254 = FACE_OUTER_BOUND ( 'NONE', #26219, .T. ) ; +#24256 = LINE ( 'NONE', #62555, #94430 ) ; +#24257 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85117, 'distance_accuracy_value', 'NONE'); +#24258 = FILL_AREA_STYLE ('',( #47200 ) ) ; +#24259 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24260 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#24261 = SURFACE_SIDE_STYLE ('',( #72207 ) ) ; +#24262 = PLANE ( 'NONE', #76272 ) ; +#24263 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#24264 = EDGE_LOOP ( 'NONE', ( #99059, #57114, #37769, #61961 ) ) ; +#24265 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000089, 2.523820061220085176, 0.000000000000000000 ) ) ; +#24266 = EDGE_CURVE ( 'NONE', #76014, #87717, #79898, .T. ) ; +#24267 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24268 = PRESENTATION_STYLE_ASSIGNMENT (( #70691 ) ) ; +#24269 = SURFACE_SIDE_STYLE ('',( #1254 ) ) ; +#24270 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.1350000000000000089 ) ) ; +#24271 = LINE ( 'NONE', #55418, #32236 ) ; +#24272 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12731 ), #43762 ) ; +#24273 = VECTOR ( 'NONE', #56625, 1000.000000000000000 ) ; +#24274 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24275 = PLANE ( 'NONE', #83242 ) ; +#24276 = EDGE_CURVE ( 'NONE', #37149, #9248, #3281, .T. ) ; +#24277 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#24278 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#24279 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24281 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24280 = AXIS2_PLACEMENT_3D ( 'NONE', #86167, #22906, #46337 ) ; +#24282 = SURFACE_STYLE_USAGE ( .BOTH. , #18063 ) ; +#24283 = FILL_AREA_STYLE_COLOUR ( '', #53771 ) ; +#24284 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.000000000000000000 ) ) ; +#24285 = VERTEX_POINT ( 'NONE', #50284 ) ; +#24286 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#24287 = ORIENTED_EDGE ( 'NONE', *, *, #45662, .F. ) ; +#24288 = VECTOR ( 'NONE', #2846, 1000.000000000000114 ) ; +#24289 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#24290 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24291 = VECTOR ( 'NONE', #77355, 1000.000000000000000 ) ; +#24292 = CARTESIAN_POINT ( 'NONE', ( 0.1930873560432360136, -1.357759925407370227, 0.8299999999999999600 ) ) ; +#24293 = FACE_OUTER_BOUND ( 'NONE', #10862, .T. ) ; +#24294 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24295 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#24296 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24297 = CARTESIAN_POINT ( 'NONE', ( -1.293371091536239970, -1.061634207873779934, 0.8100000000000000533 ) ) ; +#24298 = EDGE_CURVE ( 'NONE', #91043, #54090, #2289, .T. ) ; +#24299 = ORIENTED_EDGE ( 'NONE', *, *, #29423, .F. ) ; +#24300 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77404 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69697, #86555, #47748 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24302 = EDGE_CURVE ( 'NONE', #89625, #44029, #34448, .T. ) ; +#24301 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96296 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95450, #4061, #73518 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24303 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24304 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24305 = VERTEX_POINT ( 'NONE', #33943 ) ; +#24306 = FILL_AREA_STYLE ('',( #24817 ) ) ; +#24307 = LINE ( 'NONE', #71752, #90830 ) ; +#24308 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30727 ), #40617 ) ; +#24309 = LINE ( 'NONE', #53909, #96677 ) ; +#24310 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43802 ), #29163 ) ; +#24311 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#24312 = AXIS2_PLACEMENT_3D ( 'NONE', #24762, #62039, #54371 ) ; +#24313 = ORIENTED_EDGE ( 'NONE', *, *, #7188, .F. ) ; +#24314 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#24315 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43879 ), #61833 ) ; +#24316 = EDGE_CURVE ( 'NONE', #3356, #40138, #65546, .T. ) ; +#24317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92357, 'distance_accuracy_value', 'NONE'); +#24318 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#24319 = LINE ( 'NONE', #54440, #55148 ) ; +#24320 = ORIENTED_EDGE ( 'NONE', *, *, #79642, .T. ) ; +#24321 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#24322 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24323 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8648700000000000276 ) ) ; +#24324 = ORIENTED_EDGE ( 'NONE', *, *, #81769, .T. ) ; +#24325 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.000000000000000000 ) ) ; +#24326 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24327 = FILL_AREA_STYLE ('',( #48315 ) ) ; +#24328 = EDGE_CURVE ( 'NONE', #33782, #21155, #26778, .T. ) ; +#24329 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24330 = EDGE_LOOP ( 'NONE', ( #55385, #49804, #23209, #22334 ) ) ; +#24331 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84593, 'distance_accuracy_value', 'NONE'); +#24332 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24333 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24334 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, -3.500000000000000444, 0.000000000000000000 ) ) ; +#24335 = EDGE_LOOP ( 'NONE', ( #39137, #9851, #22016, #51187 ) ) ; +#24336 = FILL_AREA_STYLE ('',( #16607 ) ) ; +#24337 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24338 = PRESENTATION_STYLE_ASSIGNMENT (( #75547 ) ) ; +#24339 = AXIS2_PLACEMENT_3D ( 'NONE', #49379, #33050, #80539 ) ; +#24341 = EDGE_LOOP ( 'NONE', ( #86738, #576 ) ) ; +#24340 = EDGE_CURVE ( 'NONE', #99050, #39553, #33437, .T. ) ; +#24343 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#24342 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#24344 = VERTEX_POINT ( 'NONE', #89052 ) ; +#24345 = ORIENTED_EDGE ( 'NONE', *, *, #80152, .T. ) ; +#24346 = CARTESIAN_POINT ( 'NONE', ( 1.354949560415620091, -1.296162859166370307, 0.8299999999999999600 ) ) ; +#24347 = STYLED_ITEM ( 'NONE', ( #37512 ), #92751 ) ; +#24348 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27632 ), #79802 ) ; +#24349 = EDGE_CURVE ( 'NONE', #62517, #99555, #81420, .T. ) ; +#24351 = SURFACE_SIDE_STYLE ('',( #71801 ) ) ; +#24350 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24352 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#24353 = ORIENTED_EDGE ( 'NONE', *, *, #743, .F. ) ; +#24354 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53631 ), #50462 ) ; +#24355 = SURFACE_STYLE_USAGE ( .BOTH. , #64149 ) ; +#24356 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#24357 = DIRECTION ( 'NONE', ( -0.3438200982495990266, 0.000000000000000000, 0.9390355371548171348 ) ) ; +#24358 = FACE_OUTER_BOUND ( 'NONE', #47026, .T. ) ; +#24359 = ORIENTED_EDGE ( 'NONE', *, *, #13789, .T. ) ; +#24361 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24360 = SURFACE_STYLE_USAGE ( .BOTH. , #16633 ) ; +#24362 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999929778, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#24363 = ORIENTED_EDGE ( 'NONE', *, *, #74028, .F. ) ; +#24364 = ORIENTED_EDGE ( 'NONE', *, *, #34656, .F. ) ; +#24365 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51561 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31531, #69271, #22347 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24366 = ADVANCED_FACE ( 'NONE', ( #72718 ), #11349, .T. ) ; +#24367 = PLANE ( 'NONE', #94685 ) ; +#24369 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24368 = CARTESIAN_POINT ( 'NONE', ( -1.876179938779914957, -3.100000000000000533, 0.000000000000000000 ) ) ; +#24370 = SURFACE_STYLE_FILL_AREA ( #30450 ) ; +#24371 = SURFACE_SIDE_STYLE ('',( #84611 ) ) ; +#24372 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#24373 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24374 = CARTESIAN_POINT ( 'NONE', ( -2.499999999999999556, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#24375 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24376 = EDGE_LOOP ( 'NONE', ( #16182, #97188, #69608, #92049 ) ) ; +#24377 = VECTOR ( 'NONE', #67322, 1000.000000000000114 ) ; +#24378 = VECTOR ( 'NONE', #48497, 1000.000000000000000 ) ; +#24380 = FILL_AREA_STYLE ('',( #57041 ) ) ; +#24379 = LINE ( 'NONE', #47321, #99385 ) ; +#24381 = CARTESIAN_POINT ( 'NONE', ( -1.000258070327209925, -1.482334922772619468, 0.8099999999996329025 ) ) ; +#24382 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4850000000000000422, 0.2400000000000000189 ) ) ; +#24383 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24384 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24385 = CARTESIAN_POINT ( 'NONE', ( -0.5614853896103890740, 0.7099999999999999645, 0.1493506493506489563 ) ) ; +#24386 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999951594, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#24387 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#24388 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79623 ), #76526 ) ; +#24389 = FACE_OUTER_BOUND ( 'NONE', #87420, .T. ) ; +#24390 = FILL_AREA_STYLE_COLOUR ( '', #91921 ) ; +#24391 = ORIENTED_EDGE ( 'NONE', *, *, #31752, .T. ) ; +#24392 = FILL_AREA_STYLE ('',( #85634 ) ) ; +#24393 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24394 = SURFACE_STYLE_FILL_AREA ( #9955 ) ; +#24395 = PRESENTATION_STYLE_ASSIGNMENT (( #15665 ) ) ; +#24396 = EDGE_CURVE ( 'NONE', #19409, #83732, #75720, .T. ) ; +#24397 = ADVANCED_FACE ( 'NONE', ( #44078 ), #76724, .T. ) ; +#24398 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#24399 = PRESENTATION_STYLE_ASSIGNMENT (( #72334 ) ) ; +#24401 = STYLED_ITEM ( 'NONE', ( #26169 ), #15616 ) ; +#24400 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, -8.400000000000000355, -13.35000000000000142 ) ) ; +#24402 = LINE ( 'NONE', #16663, #37633 ) ; +#24403 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.90000000000000036, 0.000000000000000000 ) ) ; +#24404 = FILL_AREA_STYLE_COLOUR ( '', #99456 ) ; +#24405 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#24406 = STYLED_ITEM ( 'NONE', ( #61089 ), #44590 ) ; +#24407 = SURFACE_STYLE_USAGE ( .BOTH. , #17701 ) ; +#24408 = DIRECTION ( 'NONE', ( -0.7071064476869688420, 0.7071071146859688739, 0.000000000000000000 ) ) ; +#24409 = FACE_OUTER_BOUND ( 'NONE', #34879, .T. ) ; +#24410 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#24411 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01085786437626906110, -0.2400000000000000189 ) ) ; +#24412 = EDGE_CURVE ( 'NONE', #20389, #73661, #67057, .T. ) ; +#24413 = VERTEX_POINT ( 'NONE', #28275 ) ; +#24414 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#24415 = PLANE ( 'NONE', #61744 ) ; +#24416 = FILL_AREA_STYLE ('',( #79017 ) ) ; +#24417 = EDGE_CURVE ( 'NONE', #37511, #28951, #5230, .T. ) ; +#24418 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.100000000000000089, 1.046837090475817223E-78 ) ) ; +#24420 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24419 = SURFACE_SIDE_STYLE ('',( #8467 ) ) ; +#24421 = EDGE_CURVE ( 'NONE', #23955, #47739, #37932, .T. ) ; +#24422 = CARTESIAN_POINT ( 'NONE', ( 1.060456676593721781, -1.080732611435677670, 0.8099999999999389910 ) ) ; +#24423 = STYLED_ITEM ( 'NONE', ( #76466 ), #85840 ) ; +#24424 = VECTOR ( 'NONE', #41046, 1000.000000000000000 ) ; +#24425 = AXIS2_PLACEMENT_3D ( 'NONE', #26788, #56942, #87549 ) ; +#24426 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822763000000000133, 0.8648700000000000276 ) ) ; +#24427 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#24428 = ORIENTED_EDGE ( 'NONE', *, *, #56721, .F. ) ; +#24429 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.000000000000000000, -1.149999999999999911 ) ) ; +#24430 = LINE ( 'NONE', #55581, #2167 ) ; +#24431 = STYLED_ITEM ( 'NONE', ( #35109 ), #85176 ) ; +#24432 = AXIS2_PLACEMENT_3D ( 'NONE', #30768, #93026, #85406 ) ; +#24433 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, -0.1499999999999999944 ) ) ; +#24434 = ADVANCED_FACE ( 'NONE', ( #28754 ), #22103, .T. ) ; +#24435 = PRESENTATION_STYLE_ASSIGNMENT (( #7479 ) ) ; +#24436 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#24437 = AXIS2_PLACEMENT_3D ( 'NONE', #59508, #21150, #28323 ) ; +#24438 = EDGE_LOOP ( 'NONE', ( #77884, #54474, #45391, #75545 ) ) ; +#24439 = ADVANCED_FACE ( 'NONE', ( #61936 ), #23618, .T. ) ; +#24440 = ORIENTED_EDGE ( 'NONE', *, *, #53231, .F. ) ; +#24441 = FILL_AREA_STYLE_COLOUR ( '', #22660 ) ; +#24442 = STYLED_ITEM ( 'NONE', ( #50148 ), #80598 ) ; +#24443 = ORIENTED_EDGE ( 'NONE', *, *, #30697, .T. ) ; +#24444 = FILL_AREA_STYLE ('',( #16708 ) ) ; +#24445 = FILL_AREA_STYLE_COLOUR ( '', #10580 ) ; +#24446 = SURFACE_STYLE_USAGE ( .BOTH. , #16207 ) ; +#24447 = FILL_AREA_STYLE ('',( #49935 ) ) ; +#24448 = FILL_AREA_STYLE ('',( #10000 ) ) ; +#24449 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#24450 = EDGE_CURVE ( 'NONE', #72320, #55937, #1659, .T. ) ; +#24451 = PRODUCT_CONTEXT ( 'NONE', #52797, 'mechanical' ) ; +#24452 = PRESENTATION_STYLE_ASSIGNMENT (( #56083 ) ) ; +#24453 = FACE_OUTER_BOUND ( 'NONE', #31218, .T. ) ; +#24454 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45057 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46668, #32887, #100431 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24455 = EDGE_CURVE ( 'NONE', #19543, #55952, #15419, .T. ) ; +#24457 = ORIENTED_EDGE ( 'NONE', *, *, #76804, .T. ) ; +#24456 = EDGE_LOOP ( 'NONE', ( #43362, #25710, #11380, #65904 ) ) ; +#24458 = ORIENTED_EDGE ( 'NONE', *, *, #99984, .F. ) ; +#24459 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22824 ) ) ; +#24460 = ORIENTED_EDGE ( 'NONE', *, *, #26615, .T. ) ; +#24461 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62183, 'distance_accuracy_value', 'NONE'); +#24462 = FILL_AREA_STYLE_COLOUR ( '', #53922 ) ; +#24463 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#24464 = ORIENTED_EDGE ( 'NONE', *, *, #49345, .T. ) ; +#24465 = CARTESIAN_POINT ( 'NONE', ( -1.966666666666667007, 3.500000000000000000, 0.000000000000000000 ) ) ; +#24466 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33738, #32729, #3081 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24467 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#24468 = ORIENTED_EDGE ( 'NONE', *, *, #80028, .T. ) ; +#24469 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24470 = VECTOR ( 'NONE', #65299, 1000.000000000000114 ) ; +#24471 = ORIENTED_EDGE ( 'NONE', *, *, #29620, .F. ) ; +#24473 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#24472 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#24474 = EDGE_LOOP ( 'NONE', ( #63025, #92820, #81262, #2720 ) ) ; +#24475 = ORIENTED_EDGE ( 'NONE', *, *, #85946, .T. ) ; +#24476 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70438 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46310, #93272, #67428 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24477 = PRESENTATION_STYLE_ASSIGNMENT (( #85705 ) ) ; +#24478 = EDGE_CURVE ( 'NONE', #27880, #66478, #67803, .T. ) ; +#24479 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#24480 = SURFACE_STYLE_USAGE ( .BOTH. , #48952 ) ; +#24482 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #60089, #44208, #91187, #90689, #57193, #51404 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 4 ), + ( 0.000000000000000000, 0.5000000000000004441, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24481 = PRESENTATION_STYLE_ASSIGNMENT (( #93336 ) ) ; +#24485 = ORIENTED_EDGE ( 'NONE', *, *, #10189, .F. ) ; +#24484 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24406 ), #61998 ) ; +#24483 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24486 = LINE ( 'NONE', #53589, #72675 ) ; +#24487 = FACE_OUTER_BOUND ( 'NONE', #94393, .T. ) ; +#24488 = LINE ( 'NONE', #17273, #1675 ) ; +#24489 = ORIENTED_EDGE ( 'NONE', *, *, #92913, .T. ) ; +#24491 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.783333333333333437, 0.000000000000000000 ) ) ; +#24490 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24492 = CARTESIAN_POINT ( 'NONE', ( 0.08991555325362560191, -1.292112914554750080, 0.8299999999999999600 ) ) ; +#24493 = ORIENTED_EDGE ( 'NONE', *, *, #50247, .F. ) ; +#24494 = ORIENTED_EDGE ( 'NONE', *, *, #82496, .T. ) ; +#24495 = ADVANCED_FACE ( 'NONE', ( #62953 ), #61439, .T. ) ; +#24496 = SURFACE_SIDE_STYLE ('',( #87753 ) ) ; +#24497 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24498 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6355 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85282, #46460, #53161 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24499 = EDGE_CURVE ( 'NONE', #12278, #78426, #60022, .T. ) ; +#24500 = FILL_AREA_STYLE_COLOUR ( '', #86999 ) ; +#24501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24502 = LINE ( 'NONE', #4485, #1558 ) ; +#24503 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96152 ), #9660 ) ; +#24504 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71919, 'distance_accuracy_value', 'NONE'); +#24505 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35930 ), #50593 ) ; +#24506 = ORIENTED_EDGE ( 'NONE', *, *, #26311, .F. ) ; +#24507 = CARTESIAN_POINT ( 'NONE', ( 0.3504973566725850254, -1.231551917075010216, 0.8299999999999999600 ) ) ; +#24508 = CARTESIAN_POINT ( 'NONE', ( 0.06704264972532250622, -1.237898259965849901, 0.8100000000000000533 ) ) ; +#24509 = ORIENTED_EDGE ( 'NONE', *, *, #15476, .F. ) ; +#24510 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#24512 = SURFACE_STYLE_FILL_AREA ( #86244 ) ; +#24511 = STYLED_ITEM ( 'NONE', ( #76544 ), #57515 ) ; +#24513 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24514 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96162 ), #3267 ) ; +#24515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24516 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68474 ) ) ; +#24517 = FILL_AREA_STYLE ('',( #91402 ) ) ; +#24518 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44067 ), #8049 ) ; +#24519 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24520 = SURFACE_STYLE_FILL_AREA ( #996 ) ; +#24521 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24522 = STYLED_ITEM ( 'NONE', ( #96602 ), #6615 ) ; +#24523 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.383333333333326642, 0.000000000000000000 ) ) ; +#24524 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24525 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24526 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24527 = LINE ( 'NONE', #47967, #32068 ) ; +#24528 = FILL_AREA_STYLE_COLOUR ( '', #86488 ) ; +#24529 = VECTOR ( 'NONE', #83767, 1000.000000000000000 ) ; +#24530 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#24531 = EDGE_CURVE ( 'NONE', #24285, #38810, #77220, .T. ) ; +#24532 = EDGE_CURVE ( 'NONE', #83639, #33175, #46576, .T. ) ; +#24533 = LINE ( 'NONE', #54124, #81175 ) ; +#24534 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24535 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.499999999999960032, -0.02000000000000000042 ) ) ; +#24536 = VECTOR ( 'NONE', #23310, 1000.000000000000000 ) ; +#24537 = VECTOR ( 'NONE', #3773, 1000.000000000000000 ) ; +#24538 = ORIENTED_EDGE ( 'NONE', *, *, #38686, .F. ) ; +#24539 = SURFACE_SIDE_STYLE ('',( #31152 ) ) ; +#24540 = SURFACE_STYLE_FILL_AREA ( #9096 ) ; +#24541 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99219, 'distance_accuracy_value', 'NONE'); +#24542 = EDGE_CURVE ( 'NONE', #41373, #436, #64938, .T. ) ; +#24543 = ORIENTED_EDGE ( 'NONE', *, *, #34645, .F. ) ; +#24545 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79908, 'distance_accuracy_value', 'NONE'); +#24544 = LINE ( 'NONE', #10588, #79563 ) ; +#24546 = FILL_AREA_STYLE_COLOUR ( '', #82305 ) ; +#24547 = SURFACE_STYLE_USAGE ( .BOTH. , #86281 ) ; +#24548 = EDGE_CURVE ( 'NONE', #17228, #48033, #80784, .T. ) ; +#24549 = FACE_OUTER_BOUND ( 'NONE', #57138, .T. ) ; +#24550 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24551 = SURFACE_STYLE_FILL_AREA ( #62833 ) ; +#24552 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#24553 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24554 = FILL_AREA_STYLE ('',( #79144 ) ) ; +#24555 = VECTOR ( 'NONE', #34583, 1000.000000000000000 ) ; +#24556 = ORIENTED_EDGE ( 'NONE', *, *, #91453, .F. ) ; +#24557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24558 = ORIENTED_EDGE ( 'NONE', *, *, #25982, .T. ) ; +#24559 = PLANE ( 'NONE', #74814 ) ; +#24560 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42632, 'distance_accuracy_value', 'NONE'); +#24561 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24562 = FILL_AREA_STYLE_COLOUR ( '', #2356 ) ; +#24563 = FACE_OUTER_BOUND ( 'NONE', #4670, .T. ) ; +#24564 = CARTESIAN_POINT ( 'NONE', ( -0.1796601769484260092, -1.431361989143759894, 0.8299999999999995159 ) ) ; +#24565 = EDGE_CURVE ( 'NONE', #79240, #73910, #90968, .T. ) ; +#24566 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24567 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24568 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#24569 = ORIENTED_EDGE ( 'NONE', *, *, #25046, .F. ) ; +#24570 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8199999999999999512 ) ) ; +#24571 = SURFACE_STYLE_USAGE ( .BOTH. , #81198 ) ; +#24572 = ORIENTED_EDGE ( 'NONE', *, *, #14191, .T. ) ; +#24573 = EDGE_CURVE ( 'NONE', #85966, #73645, #87412, .T. ) ; +#24574 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.5000000000000000000, -12.64499999999999957 ) ) ; +#24575 = VECTOR ( 'NONE', #96825, 1000.000000000000000 ) ; +#24576 = ORIENTED_EDGE ( 'NONE', *, *, #57940, .T. ) ; +#24577 = LINE ( 'NONE', #26563, #34906 ) ; +#24578 = FILL_AREA_STYLE_COLOUR ( '', #75049 ) ; +#24579 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24580 = LINE ( 'NONE', #3069, #26752 ) ; +#24581 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55545 ), #34333 ) ; +#24582 = STYLED_ITEM ( 'NONE', ( #61137 ), #93391 ) ; +#24583 = CARTESIAN_POINT ( 'NONE', ( 8.754364000000000701, 11.38250200000000056, 0.8991599999999999593 ) ) ; +#24584 = SURFACE_STYLE_USAGE ( .BOTH. , #49050 ) ; +#24585 = CARTESIAN_POINT ( 'NONE', ( 2.523820061220085176, -3.099999999999960121, 0.000000000000000000 ) ) ; +#24586 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24587 = EDGE_CURVE ( 'NONE', #41874, #47242, #19480, .T. ) ; +#24589 = ORIENTED_EDGE ( 'NONE', *, *, #94361, .T. ) ; +#24588 = VERTEX_POINT ( 'NONE', #50650 ) ; +#24590 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#24591 = FILL_AREA_STYLE ('',( #54705 ) ) ; +#24592 = VECTOR ( 'NONE', #33347, 1000.000000000000000 ) ; +#24593 = PRESENTATION_STYLE_ASSIGNMENT (( #93444 ) ) ; +#24594 = ORIENTED_EDGE ( 'NONE', *, *, #2544, .F. ) ; +#24595 = PLANE ( 'NONE', #26500 ) ; +#24596 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22395, #15718, #7992 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24598 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.100000000000000311, 0.000000000000000000 ) ) ; +#24597 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24599 = ORIENTED_EDGE ( 'NONE', *, *, #91874, .F. ) ; +#24600 = ORIENTED_EDGE ( 'NONE', *, *, #8251, .T. ) ; +#24601 = VECTOR ( 'NONE', #1320, 1000.000000000000000 ) ; +#24602 = SURFACE_STYLE_USAGE ( .BOTH. , #11156 ) ; +#24603 = PRESENTATION_STYLE_ASSIGNMENT (( #78663 ) ) ; +#24604 = CARTESIAN_POINT ( 'NONE', ( -0.03333333333333900195, 3.500000000000000000, 0.000000000000000000 ) ) ; +#24605 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86505 ) ) ; +#24606 = SURFACE_STYLE_USAGE ( .BOTH. , #65361 ) ; +#24607 = ORIENTED_EDGE ( 'NONE', *, *, #29720, .F. ) ; +#24608 = EDGE_LOOP ( 'NONE', ( #98064, #77902, #78044, #57820 ) ) ; +#24609 = EDGE_LOOP ( 'NONE', ( #88139, #82182, #17397, #60945, #54447, #97013 ) ) ; +#24610 = SURFACE_STYLE_FILL_AREA ( #95487 ) ; +#24611 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96185 ), #36028 ) ; +#24612 = EDGE_CURVE ( 'NONE', #8949, #86833, #81789, .T. ) ; +#24613 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24614 = STYLED_ITEM ( 'NONE', ( #46515 ), #69425 ) ; +#24615 = ORIENTED_EDGE ( 'NONE', *, *, #33779, .T. ) ; +#24616 = FILL_AREA_STYLE_COLOUR ( '', #14579 ) ; +#24617 = ORIENTED_EDGE ( 'NONE', *, *, #54144, .F. ) ; +#24618 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.899999999999999911, 0.000000000000000000 ) ) ; +#24619 = EDGE_LOOP ( 'NONE', ( #95834, #37300, #9744, #4585 ) ) ; +#24620 = EDGE_CURVE ( 'NONE', #30844, #9892, #32789, .T. ) ; +#24621 = LINE ( 'NONE', #86871, #57975 ) ; +#24622 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#24623 = LINE ( 'NONE', #93967, #12642 ) ; +#24624 = SURFACE_SIDE_STYLE ('',( #9680 ) ) ; +#24625 = EDGE_CURVE ( 'NONE', #27194, #79071, #95541, .T. ) ; +#24626 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24627 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5014 ) ) ; +#24628 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#24629 = SURFACE_STYLE_FILL_AREA ( #29715 ) ; +#24631 = CARTESIAN_POINT ( 'NONE', ( 1.652046208920949999, -1.504992180692799941, 0.8299999999999999600 ) ) ; +#24630 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24632 = CARTESIAN_POINT ( 'NONE', ( 1.689681756505250210, -0.9624218420162741205, 0.8299999999999990719 ) ) ; +#24633 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999990674, 0.1829999999999790128 ) ) ; +#24634 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 5.910594999999999821, 0.8648700000000000276 ) ) ; +#24635 = ORIENTED_EDGE ( 'NONE', *, *, #49741, .F. ) ; +#24636 = ADVANCED_FACE ( 'NONE', ( #34829 ), #48633, .T. ) ; +#24637 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#24638 = LINE ( 'NONE', #1108, #100042 ) ; +#24639 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6700000000000000400, 0.1999999999999999833 ) ) ; +#24640 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24641 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#24642 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70206 ) ) ; +#24643 = PRESENTATION_STYLE_ASSIGNMENT (( #63441 ) ) ; +#24644 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8648700000000000276 ) ) ; +#24645 = ORIENTED_EDGE ( 'NONE', *, *, #89575, .F. ) ; +#24646 = EDGE_CURVE ( 'NONE', #42980, #41874, #57303, .T. ) ; +#24647 = EDGE_LOOP ( 'NONE', ( #35678, #30302, #18995, #43766, #60929, #97682 ) ) ; +#24648 = SURFACE_STYLE_FILL_AREA ( #49118 ) ; +#24649 = AXIS2_PLACEMENT_3D ( 'NONE', #59548, #12441, #85860 ) ; +#24650 = EDGE_CURVE ( 'NONE', #79461, #12592, #65424, .T. ) ; +#24651 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69712 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100014, #7110, #92929 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24652 = SURFACE_STYLE_FILL_AREA ( #94001 ) ; +#24653 = ORIENTED_EDGE ( 'NONE', *, *, #1993, .T. ) ; +#24654 = CARTESIAN_POINT ( 'NONE', ( 1.825861765333669950, -0.9394184040112200096, 0.8100000000000008304 ) ) ; +#24655 = PLANE ( 'NONE', #75618 ) ; +#24656 = CARTESIAN_POINT ( 'NONE', ( -0.01281341696057500083, -1.096743473147149928, 0.8300000000000005151 ) ) ; +#24657 = FILL_AREA_STYLE ('',( #54791 ) ) ; +#24658 = PRESENTATION_STYLE_ASSIGNMENT (( #79256 ) ) ; +#24659 = EDGE_CURVE ( 'NONE', #43057, #60265, #88929, .T. ) ; +#24660 = FILL_AREA_STYLE ('',( #47091 ) ) ; +#24661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24662 = EDGE_CURVE ( 'NONE', #19475, #88969, #25642, .T. ) ; +#24663 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#24664 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24665 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19028, 'distance_accuracy_value', 'NONE'); +#24666 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24667 = STYLED_ITEM ( 'NONE', ( #6684 ), #65026 ) ; +#24668 = VECTOR ( 'NONE', #42258, 1000.000000000000000 ) ; +#24669 = ORIENTED_EDGE ( 'NONE', *, *, #54732, .T. ) ; +#24670 = SURFACE_SIDE_STYLE ('',( #80283 ) ) ; +#24671 = ORIENTED_EDGE ( 'NONE', *, *, #10056, .T. ) ; +#24672 = DIRECTION ( 'NONE', ( -0.7071090539100497452, -0.7071045084557405769, 0.000000000000000000 ) ) ; +#24674 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54109, 'distance_accuracy_value', 'NONE'); +#24673 = AXIS2_PLACEMENT_3D ( 'NONE', #38883, #45993, #48061 ) ; +#24675 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46112, 'distance_accuracy_value', 'NONE'); +#24676 = FILL_AREA_STYLE ('',( #23138 ) ) ; +#24677 = FACE_OUTER_BOUND ( 'NONE', #34017, .T. ) ; +#24678 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#24679 = CARTESIAN_POINT ( 'NONE', ( -0.008589415658712419230, -1.182875588085640306, 0.8100000000000000533 ) ) ; +#24680 = SURFACE_STYLE_USAGE ( .BOTH. , #9742 ) ; +#24681 = SURFACE_SIDE_STYLE ('',( #94567 ) ) ; +#24683 = VERTEX_POINT ( 'NONE', #73608 ) ; +#24682 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24684 = LINE ( 'NONE', #80807, #51036 ) ; +#24685 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24686 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#24687 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6322, 'distance_accuracy_value', 'NONE'); +#24688 = EDGE_LOOP ( 'NONE', ( #40793, #12323, #60373, #78881 ) ) ; +#24689 = CARTESIAN_POINT ( 'NONE', ( 1.190385334006407225, -1.222953069365735779, 0.8099999999998497291 ) ) ; +#24690 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89875 ) ) ; +#24691 = ORIENTED_EDGE ( 'NONE', *, *, #100061, .F. ) ; +#24692 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24693 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30612 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93938, #94473, #86841 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24695 = SURFACE_STYLE_FILL_AREA ( #10240 ) ; +#24696 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24697 = PRESENTATION_STYLE_ASSIGNMENT (( #76379 ) ) ; +#24698 = FILL_AREA_STYLE_COLOUR ( '', #5456 ) ; +#24699 = EDGE_CURVE ( 'NONE', #76830, #64661, #3654, .T. ) ; +#24700 = ORIENTED_EDGE ( 'NONE', *, *, #69280, .T. ) ; +#24701 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65323 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1822, #786, #40628 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24702 = CYLINDRICAL_SURFACE ( 'NONE', #58846, 0.009999999999999998473 ) ; +#24703 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 8.958225000000000549, 0.8648700000000000276 ) ) ; +#24704 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78204, #56251, #62902, #24618 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24705 = SURFACE_SIDE_STYLE ('',( #70102 ) ) ; +#24706 = EDGE_CURVE ( 'NONE', #79825, #84697, #75121, .T. ) ; +#24707 = CARTESIAN_POINT ( 'NONE', ( 0.4415831003499929852, -0.9994927481818659531, 0.8300000000000002931 ) ) ; +#24708 = EDGE_LOOP ( 'NONE', ( #7143, #51429, #6854, #10939 ) ) ; +#24709 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24710 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24711 = LINE ( 'NONE', #41023, #32662 ) ; +#24712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24713 = PRESENTATION_STYLE_ASSIGNMENT (( #93058 ) ) ; +#24714 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#24715 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24716 = ORIENTED_EDGE ( 'NONE', *, *, #77382, .F. ) ; +#24718 = ORIENTED_EDGE ( 'NONE', *, *, #61336, .T. ) ; +#24717 = ORIENTED_EDGE ( 'NONE', *, *, #46241, .T. ) ; +#24719 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#24720 = PRODUCT ( 'Submodel-L0201_part_L0201', 'Submodel-L0201_part_L0201', '', ( #41757 ) ) ; +#24721 = ORIENTED_EDGE ( 'NONE', *, *, #90629, .T. ) ; +#24722 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93066 ), #31162 ) ; +#24723 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14783 ) ) ; +#24724 = ADVANCED_FACE ( 'NONE', ( #98011 ), #99491, .F. ) ; +#24725 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24726 = ORIENTED_EDGE ( 'NONE', *, *, #67312, .T. ) ; +#24727 = ORIENTED_EDGE ( 'NONE', *, *, #92594, .T. ) ; +#24728 = VECTOR ( 'NONE', #23597, 1000.000000000000000 ) ; +#24729 = PLANE ( 'NONE', #85027 ) ; +#24730 = SURFACE_SIDE_STYLE ('',( #25713 ) ) ; +#24731 = PRESENTATION_STYLE_ASSIGNMENT (( #2229 ) ) ; +#24732 = ORIENTED_EDGE ( 'NONE', *, *, #26421, .T. ) ; +#24733 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#24734 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24735 = SURFACE_SIDE_STYLE ('',( #94617 ) ) ; +#24736 = ORIENTED_EDGE ( 'NONE', *, *, #11916, .T. ) ; +#24737 = EDGE_CURVE ( 'NONE', #1465, #54031, #22606, .T. ) ; +#24738 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80021 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77799, #30820, #31833 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24739 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24740 = SURFACE_SIDE_STYLE ('',( #10798 ) ) ; +#24741 = FILL_AREA_STYLE_COLOUR ( '', #5575 ) ; +#24742 = ORIENTED_EDGE ( 'NONE', *, *, #98982, .F. ) ; +#24743 = VECTOR ( 'NONE', #98282, 1000.000000000000000 ) ; +#24744 = AXIS2_PLACEMENT_3D ( 'NONE', #46042, #77223, #47606 ) ; +#24745 = LINE ( 'NONE', #50105, #82872 ) ; +#24746 = EDGE_LOOP ( 'NONE', ( #63876, #30029, #78178, #56851 ) ) ; +#24747 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24748 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#24749 = ADVANCED_FACE ( 'NONE', ( #82771 ), #29634, .T. ) ; +#24750 = AXIS2_PLACEMENT_3D ( 'NONE', #11651, #66382, #97491 ) ; +#24751 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24752 = ORIENTED_EDGE ( 'NONE', *, *, #69531, .F. ) ; +#24753 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#24754 = EDGE_CURVE ( 'NONE', #87607, #16296, #82287, .T. ) ; +#24755 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24756 = LINE ( 'NONE', #93102, #22506 ) ; +#24757 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#24758 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67062, 'distance_accuracy_value', 'NONE'); +#24759 = CARTESIAN_POINT ( 'NONE', ( -1.000023319491960105, -0.9315058289328710384, 0.8100000000000000533 ) ) ; +#24760 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#24761 = CIRCLE ( 'NONE', #1923, 1.200947669413299890 ) ; +#24762 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#24763 = ADVANCED_FACE ( 'NONE', ( #4640 ), #35836, .T. ) ; +#24764 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#24765 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#24766 = ADVANCED_FACE ( 'NONE', ( #77108 ), #100467, .T. ) ; +#24767 = ORIENTED_EDGE ( 'NONE', *, *, #41143, .F. ) ; +#24768 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24769 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24770 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220025313, -2.700000000000000178, 0.000000000000000000 ) ) ; +#24771 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11600 ) ) ; +#24772 = EDGE_CURVE ( 'NONE', #66295, #55093, #99101, .T. ) ; +#24774 = EDGE_CURVE ( 'NONE', #28082, #25853, #23005, .T. ) ; +#24773 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, 0.000000000000000000 ) ) ; +#24775 = PRESENTATION_STYLE_ASSIGNMENT (( #47204 ) ) ; +#24776 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24777 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24778 = ORIENTED_EDGE ( 'NONE', *, *, #21072, .F. ) ; +#24779 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24780 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.500000000000000000, 0.8299999999999999600 ) ) ; +#24781 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#24782 = EDGE_CURVE ( 'NONE', #10705, #58744, #15811, .T. ) ; +#24783 = LINE ( 'NONE', #71715, #90950 ) ; +#24784 = STYLED_ITEM ( 'NONE', ( #88907 ), #18430 ) ; +#24785 = SURFACE_SIDE_STYLE ('',( #94155 ) ) ; +#24786 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#24787 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75270 ), #88312 ) ; +#24788 = ADVANCED_FACE ( 'NONE', ( #86283 ), #45927, .F. ) ; +#24789 = PLANE ( 'NONE', #86676 ) ; +#24790 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51653 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59457, #83890, #45053 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24791 = SURFACE_SIDE_STYLE ('',( #31910 ) ) ; +#24792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24793 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#24794 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#24795 = EDGE_LOOP ( 'NONE', ( #6564, #16528, #51342, #2976 ) ) ; +#24796 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24797 = ORIENTED_EDGE ( 'NONE', *, *, #31289, .T. ) ; +#24798 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99417, 'distance_accuracy_value', 'NONE'); +#24799 = STYLED_ITEM ( 'NONE', ( #69644 ), #8378 ) ; +#24801 = FILL_AREA_STYLE_COLOUR ( '', #76468 ) ; +#24800 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33059, #55052, #56575, #32568, #32054, #79530, #86154, #7964, #70854, #24931, #9496, #40735, #71871, #94304, #94807, #39198, #40228, #17711, #15688 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.319567991779797155E-05, 2.576643077249152024E-05, 3.773340996187479052E-05, 4.936825240056165882E-05, 6.061772559639369833E-05, 7.172063664106980243E-05, 8.254407109509321976E-05, 9.349111382289933768E-05, 0.0001044267948011702514, 0.0001155026697639780495, 0.0001268633985066008006, 0.0001386834324107895074, 0.0001507973853380191562, 0.0001632259768666851686, 0.0001759815166969652103, 0.0001891722082235626165 ), + .UNSPECIFIED. ) ; +#24802 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#24803 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24804 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72255 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38612, #45726, #23814 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24805 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#24806 = FILL_AREA_STYLE_COLOUR ( '', #12404 ) ; +#24807 = FACE_OUTER_BOUND ( 'NONE', #3809, .T. ) ; +#24808 = ORIENTED_EDGE ( 'NONE', *, *, #100836, .T. ) ; +#24809 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24810 = VECTOR ( 'NONE', #36285, 1000.000000000000000 ) ; +#24811 = FILL_AREA_STYLE_COLOUR ( '', #24211 ) ; +#24812 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98808, 'distance_accuracy_value', 'NONE'); +#24813 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#24814 = PRESENTATION_STYLE_ASSIGNMENT (( #87070 ) ) ; +#24815 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24816 = ORIENTED_EDGE ( 'NONE', *, *, #48057, .F. ) ; +#24817 = FILL_AREA_STYLE_COLOUR ( '', #72014 ) ; +#24818 = PRESENTATION_STYLE_ASSIGNMENT (( #86560 ) ) ; +#24819 = PLANE ( 'NONE', #44490 ) ; +#24820 = STYLED_ITEM ( 'NONE', ( #9856 ), #25324 ) ; +#24821 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.100000000000000089, 2.617092726158356351E-79 ) ) ; +#24823 = ORIENTED_EDGE ( 'NONE', *, *, #84151, .T. ) ; +#24822 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#24824 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.03429000000000000103 ) ) ; +#24825 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77183, 'distance_accuracy_value', 'NONE'); +#24826 = LINE ( 'NONE', #70742, #80155 ) ; +#24827 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24828 = EDGE_CURVE ( 'NONE', #28239, #91027, #36086, .T. ) ; +#24829 = SURFACE_STYLE_FILL_AREA ( #33989 ) ; +#24830 = EDGE_LOOP ( 'NONE', ( #68378, #6023, #4989, #18235 ) ) ; +#24831 = FILL_AREA_STYLE_COLOUR ( '', #25246 ) ; +#24832 = FILL_AREA_STYLE ('',( #80443 ) ) ; +#24833 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24834 = ORIENTED_EDGE ( 'NONE', *, *, #29134, .F. ) ; +#24836 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#24835 = VECTOR ( 'NONE', #85394, 1000.000000000000000 ) ; +#24837 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24838 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#24839 = VECTOR ( 'NONE', #94984, 999.9999999999998863 ) ; +#24840 = AXIS2_PLACEMENT_3D ( 'NONE', #25088, #62363, #63872 ) ; +#24841 = VERTEX_POINT ( 'NONE', #49905 ) ; +#24843 = ORIENTED_EDGE ( 'NONE', *, *, #97383, .F. ) ; +#24842 = FACE_OUTER_BOUND ( 'NONE', #55110, .T. ) ; +#24844 = SURFACE_STYLE_FILL_AREA ( #8382 ) ; +#24845 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#24846 = SURFACE_STYLE_USAGE ( .BOTH. , #87600 ) ; +#24847 = CARTESIAN_POINT ( 'NONE', ( -0.3663668861142549971, -1.072315624320830274, 0.8299999999999999600 ) ) ; +#24848 = VERTEX_POINT ( 'NONE', #49377 ) ; +#24849 = SURFACE_STYLE_USAGE ( .BOTH. , #56997 ) ; +#24850 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853448918, 0.2349715759269650206, 0.8100000000000000533 ) ) ; +#24851 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24852 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24853 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21730 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94071, #70111, #70622 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24854 = CARTESIAN_POINT ( 'NONE', ( -1.783333333333333437, 3.099999999999989875, 0.000000000000000000 ) ) ; +#24855 = ORIENTED_EDGE ( 'NONE', *, *, #83718, .F. ) ; +#24856 = SURFACE_STYLE_FILL_AREA ( #94735 ) ; +#24857 = ORIENTED_EDGE ( 'NONE', *, *, #54297, .T. ) ; +#24858 = STYLED_ITEM ( 'NONE', ( #21800 ), #59954 ) ; +#24859 = ORIENTED_EDGE ( 'NONE', *, *, #22959, .T. ) ; +#24860 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24861 = VECTOR ( 'NONE', #16796, 1000.000000000000114 ) ; +#24863 = CYLINDRICAL_SURFACE ( 'NONE', #80970, 1.293010265664959801 ) ; +#24862 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#24864 = FILL_AREA_STYLE ('',( #16623 ) ) ; +#24865 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24866 = STYLED_ITEM ( 'NONE', ( #33373 ), #59252 ) ; +#24867 = EDGE_LOOP ( 'NONE', ( #34556, #47519, #40246, #77922 ) ) ; +#24868 = AXIS2_PLACEMENT_3D ( 'NONE', #8558, #40829, #72439 ) ; +#24869 = SURFACE_STYLE_USAGE ( .BOTH. , #95743 ) ; +#24870 = PRESENTATION_STYLE_ASSIGNMENT (( #94746 ) ) ; +#24871 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#24872 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34705 ) ) ; +#24873 = EDGE_LOOP ( 'NONE', ( #77819, #18925, #78785, #67971 ) ) ; +#24874 = SURFACE_SIDE_STYLE ('',( #92725 ) ) ; +#24875 = VERTEX_POINT ( 'NONE', #26412 ) ; +#24876 = ORIENTED_EDGE ( 'NONE', *, *, #71214, .T. ) ; +#24877 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24878 = SURFACE_STYLE_USAGE ( .BOTH. , #72295 ) ; +#24879 = FACE_OUTER_BOUND ( 'NONE', #28870, .T. ) ; +#24880 = AXIS2_PLACEMENT_3D ( 'NONE', #47947, #94387, #25000 ) ; +#24881 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#24883 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#24884 = FACE_OUTER_BOUND ( 'NONE', #69730, .T. ) ; +#24885 = CARTESIAN_POINT ( 'NONE', ( -0.08340097402597419773, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#24886 = VECTOR ( 'NONE', #96568, 1000.000000000000114 ) ; +#24887 = ORIENTED_EDGE ( 'NONE', *, *, #61487, .T. ) ; +#24888 = FACE_OUTER_BOUND ( 'NONE', #6683, .T. ) ; +#24889 = VECTOR ( 'NONE', #89375, 1000.000000000000114 ) ; +#24890 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24891 = LINE ( 'NONE', #87148, #87589 ) ; +#24893 = EDGE_CURVE ( 'NONE', #38779, #99681, #67193, .T. ) ; +#24892 = LINE ( 'NONE', #46286, #38292 ) ; +#24894 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#24895 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#24896 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70541 ), #41202 ) ; +#24897 = CARTESIAN_POINT ( 'NONE', ( 3.539405124874955622, 7.720788124874957248, 0.8648700000000000276 ) ) ; +#24898 = ORIENTED_EDGE ( 'NONE', *, *, #11505, .T. ) ; +#24899 = LINE ( 'NONE', #94781, #85235 ) ; +#24900 = PRESENTATION_STYLE_ASSIGNMENT (( #32024 ) ) ; +#24901 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24902 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#24903 = STYLED_ITEM ( 'NONE', ( #47874 ), #52191 ) ; +#24904 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#24905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72149, 'distance_accuracy_value', 'NONE'); +#24906 = AXIS2_PLACEMENT_3D ( 'NONE', #19919, #12175, #65895 ) ; +#24907 = FACE_OUTER_BOUND ( 'NONE', #89764, .T. ) ; +#24908 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, 0.2999999999999999889 ) ) ; +#24909 = LINE ( 'NONE', #78482, #48100 ) ; +#24910 = EDGE_CURVE ( 'NONE', #63665, #54703, #20224, .T. ) ; +#24911 = PLANE ( 'NONE', #19774 ) ; +#24912 = PLANE ( 'NONE', #3312 ) ; +#24913 = SURFACE_STYLE_FILL_AREA ( #55550 ) ; +#24914 = PRESENTATION_STYLE_ASSIGNMENT (( #94792 ) ) ; +#24915 = AXIS2_PLACEMENT_3D ( 'NONE', #80482, #845, #49333 ) ; +#24916 = SURFACE_STYLE_FILL_AREA ( #41225 ) ; +#24917 = SURFACE_STYLE_USAGE ( .BOTH. , #61689 ) ; +#24918 = CYLINDRICAL_SURFACE ( 'NONE', #42388, 0.04999999999999991257 ) ; +#24919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21661 ) ) ; +#24921 = SURFACE_STYLE_USAGE ( .BOTH. , #55559 ) ; +#24922 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #38904, #1625, #95004, #100549, #53718, #8665, #62403, #14860, #85863, #93486, #39914, #54758, #70536, #584, #71048, #7159, #31740, #88897, #49101 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.326044875314598131E-05, 2.608344456781442345E-05, 3.857776305804214053E-05, 5.075577902222771191E-05, 6.263832161151490475E-05, 7.405913006467100535E-05, 8.519357832649408432E-05, 9.618709120644524779E-05, 0.0001071920259210406499, 0.0001180726986758551711, 0.0001292343259962875171, 0.0001405432905424168662, 0.0001522396623056442510, 0.0001642699272808204156, 0.0001769071568878588974, 0.0001901726204126520875 ), + .UNSPECIFIED. ) ; +#24923 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01085786437626905764, -0.2434314575050761931 ) ) ; +#24924 = ORIENTED_EDGE ( 'NONE', *, *, #39190, .F. ) ; +#24925 = FILL_AREA_STYLE_COLOUR ( '', #88633 ) ; +#24926 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#24928 = STYLED_ITEM ( 'NONE', ( #1939 ), #37523 ) ; +#24927 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24929 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24930 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10658, 'distance_accuracy_value', 'NONE'); +#24932 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.05000000000000001665, 0.2100000000000000200 ) ) ; +#24931 = CARTESIAN_POINT ( 'NONE', ( -0.01972870844762369957, -1.247965265924660061, 0.8300000000000002931 ) ) ; +#24933 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#24934 = FACE_OUTER_BOUND ( 'NONE', #45335, .T. ) ; +#24935 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6864 ), #20002 ) ; +#24936 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51018 ) ) ; +#24937 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24938 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#24939 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#24940 = VERTEX_POINT ( 'NONE', #34586 ) ; +#24941 = FILL_AREA_STYLE ('',( #35105 ) ) ; +#24942 = AXIS2_PLACEMENT_3D ( 'NONE', #37880, #68979, #558 ) ; +#24943 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220025313, -2.499999999999999556, -0.02000000000000000042 ) ) ; +#24944 = AXIS2_PLACEMENT_3D ( 'NONE', #99240, #68161, #22731 ) ; +#24945 = CARTESIAN_POINT ( 'NONE', ( 1.724073170230389973, -1.220939016933670018, 0.8299999999999994049 ) ) ; +#24946 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50184, 'distance_accuracy_value', 'NONE'); +#24947 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20073, 'distance_accuracy_value', 'NONE'); +#24948 = ADVANCED_FACE ( 'NONE', ( #11483 ), #19740, .F. ) ; +#24949 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#24950 = ORIENTED_EDGE ( 'NONE', *, *, #56906, .T. ) ; +#24951 = ORIENTED_EDGE ( 'NONE', *, *, #32186, .F. ) ; +#24952 = FILL_AREA_STYLE ('',( #41261 ) ) ; +#24953 = ORIENTED_EDGE ( 'NONE', *, *, #99789, .T. ) ; +#24954 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#24955 = SURFACE_SIDE_STYLE ('',( #57610 ) ) ; +#24956 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #47562 ) ; +#24958 = ORIENTED_EDGE ( 'NONE', *, *, #75675, .T. ) ; +#24957 = ORIENTED_EDGE ( 'NONE', *, *, #56402, .T. ) ; +#24959 = ORIENTED_EDGE ( 'NONE', *, *, #16458, .F. ) ; +#24960 = ORIENTED_EDGE ( 'NONE', *, *, #18381, .F. ) ; +#24961 = LINE ( 'NONE', #84690, #13130 ) ; +#24962 = PRESENTATION_STYLE_ASSIGNMENT (( #87721 ) ) ; +#24963 = EDGE_LOOP ( 'NONE', ( #1562, #46890, #34746, #53838, #498, #37261, #96812, #31164 ) ) ; +#24964 = EDGE_CURVE ( 'NONE', #3092, #44510, #81564, .T. ) ; +#24965 = SURFACE_STYLE_USAGE ( .BOTH. , #40269 ) ; +#24966 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, 0.000000000000000000 ) ) ; +#24967 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44121 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37441, #14388, #72094 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24968 = ORIENTED_EDGE ( 'NONE', *, *, #83314, .T. ) ; +#24969 = SURFACE_STYLE_USAGE ( .BOTH. , #48449 ) ; +#24970 = ORIENTED_EDGE ( 'NONE', *, *, #97444, .F. ) ; +#24971 = CARTESIAN_POINT ( 'NONE', ( 8.842706249749912928, 10.11080875025008829, 0.8991599999999999593 ) ) ; +#24972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64092 ), #28232 ) ; +#24973 = VERTEX_POINT ( 'NONE', #82046 ) ; +#24974 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10956 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77005, #38711, #86688 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#24975 = ORIENTED_EDGE ( 'NONE', *, *, #21591, .T. ) ; +#24976 = CARTESIAN_POINT ( 'NONE', ( 0.3916958651482640441, -1.284685391536070087, 0.8300000000000004041 ) ) ; +#24977 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24978 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#24980 = EDGE_LOOP ( 'NONE', ( #25684, #75541, #60456, #86899 ) ) ; +#24979 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#24981 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#24982 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#24983 = AXIS2_PLACEMENT_3D ( 'NONE', #25762, #88039, #10323 ) ; +#24984 = VECTOR ( 'NONE', #90932, 1000.000000000000000 ) ; +#24985 = VERTEX_POINT ( 'NONE', #11988 ) ; +#24986 = SURFACE_STYLE_FILL_AREA ( #2485 ) ; +#24987 = EDGE_LOOP ( 'NONE', ( #53691, #92135, #85584, #14338 ) ) ; +#24988 = ORIENTED_EDGE ( 'NONE', *, *, #58285, .T. ) ; +#24989 = EDGE_CURVE ( 'NONE', #37871, #88475, #61701, .T. ) ; +#24991 = FILL_AREA_STYLE_COLOUR ( '', #96031 ) ; +#24990 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#24992 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#24993 = EDGE_CURVE ( 'NONE', #27223, #34867, #92176, .T. ) ; +#24994 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#24995 = STYLED_ITEM ( 'NONE', ( #63450 ), #18917 ) ; +#24996 = CARTESIAN_POINT ( 'NONE', ( -0.4015417829630419932, -1.199500944507529976, 0.8100000000000000533 ) ) ; +#24998 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #69705, #31427, #7356, #30386 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#24997 = VECTOR ( 'NONE', #16764, 1000.000000000000000 ) ; +#24999 = LINE ( 'NONE', #18797, #29905 ) ; +#25000 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25001 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25002 = SURFACE_STYLE_USAGE ( .BOTH. , #72423 ) ; +#25003 = ORIENTED_EDGE ( 'NONE', *, *, #81692, .F. ) ; +#25004 = CARTESIAN_POINT ( 'NONE', ( 0.3953060575754059891, -1.200834233358659908, 0.8299999999999999600 ) ) ; +#25005 = CARTESIAN_POINT ( 'NONE', ( 0.01105796065628599986, -1.194792006717259936, 0.8299999999999999600 ) ) ; +#25006 = ORIENTED_EDGE ( 'NONE', *, *, #97900, .F. ) ; +#25007 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74293 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41791, #95360, #48460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25008 = PRESENTATION_STYLE_ASSIGNMENT (( #64780 ) ) ; +#25009 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#25010 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47984 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89047, #10846, #58448 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25011 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25013 = EDGE_CURVE ( 'NONE', #26486, #74469, #76874, .T. ) ; +#25012 = LINE ( 'NONE', #8549, #82326 ) ; +#25014 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#25016 = PRESENTATION_STYLE_ASSIGNMENT (( #94398 ) ) ; +#25015 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#25017 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25018 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25019 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25020 = SURFACE_SIDE_STYLE ('',( #78589 ) ) ; +#25021 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.4600000000000000200, -1.129999999999999893 ) ) ; +#25022 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25023 = FACE_OUTER_BOUND ( 'NONE', #84211, .T. ) ; +#25024 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25025 = FACE_OUTER_BOUND ( 'NONE', #68526, .T. ) ; +#25026 = SURFACE_STYLE_FILL_AREA ( #57179 ) ; +#25027 = LINE ( 'NONE', #71462, #50607 ) ; +#25028 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25029 = AXIS2_PLACEMENT_3D ( 'NONE', #58036, #27361, #60899 ) ; +#25030 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25031 = PRESENTATION_STYLE_ASSIGNMENT (( #94909 ) ) ; +#25032 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36192, 'distance_accuracy_value', 'NONE'); +#25033 = ORIENTED_EDGE ( 'NONE', *, *, #41908, .T. ) ; +#25034 = FILL_AREA_STYLE ('',( #64812 ) ) ; +#25035 = PRESENTATION_STYLE_ASSIGNMENT (( #16797 ) ) ; +#25036 = ORIENTED_EDGE ( 'NONE', *, *, #17513, .F. ) ; +#25037 = LINE ( 'NONE', #30614, #9022 ) ; +#25038 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#25039 = FILL_AREA_STYLE_COLOUR ( '', #22575 ) ; +#25040 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25041 = SURFACE_SIDE_STYLE ('',( #47476 ) ) ; +#25042 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 5.245913999999999966, 0.8648700000000000276 ) ) ; +#25043 = AXIS2_PLACEMENT_3D ( 'NONE', #42851, #27041, #11104 ) ; +#25044 = VECTOR ( 'NONE', #39466, 1000.000000000000000 ) ; +#25045 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#25046 = EDGE_CURVE ( 'NONE', #62000, #40281, #100725, .T. ) ; +#25047 = EDGE_LOOP ( 'NONE', ( #234, #48977, #84062, #60887 ) ) ; +#25048 = FACE_OUTER_BOUND ( 'NONE', #13722, .T. ) ; +#25049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27823 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10301, #47181, #64530 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25050 = EDGE_LOOP ( 'NONE', ( #27831, #47271, #1179, #73547 ) ) ; +#25051 = SURFACE_STYLE_FILL_AREA ( #10603 ) ; +#25052 = SURFACE_STYLE_FILL_AREA ( #72478 ) ; +#25053 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#25054 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#25055 = CARTESIAN_POINT ( 'NONE', ( -0.1429571421083520033, -1.443372874996269983, 0.8299999999999995159 ) ) ; +#25056 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25057 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23465 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27782, #74225, #69406 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25058 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#25059 = VECTOR ( 'NONE', #82043, 1000.000000000000000 ) ; +#25060 = SURFACE_STYLE_USAGE ( .BOTH. , #70985 ) ; +#25061 = LINE ( 'NONE', #2058, #5393 ) ; +#25062 = VERTEX_POINT ( 'NONE', #14537 ) ; +#25063 = VECTOR ( 'NONE', #31523, 1000.000000000000000 ) ; +#25064 = EDGE_CURVE ( 'NONE', #2457, #88816, #36588, .T. ) ; +#25065 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#25066 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#25067 = ORIENTED_EDGE ( 'NONE', *, *, #96393, .F. ) ; +#25068 = CYLINDRICAL_SURFACE ( 'NONE', #89887, 0.2000000000000000944 ) ; +#25069 = VECTOR ( 'NONE', #86457, 1000.000000000000000 ) ; +#25070 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25071 = VERTEX_POINT ( 'NONE', #38076 ) ; +#25072 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21161 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12587, #19825, #19307 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25073 = FILL_AREA_STYLE ('',( #41383 ) ) ; +#25074 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25075 = VECTOR ( 'NONE', #45642, 1000.000000000000000 ) ; +#25076 = CARTESIAN_POINT ( 'NONE', ( -1.383443874258670991, 1.573160335515870312, 0.8100000000000003864 ) ) ; +#25077 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2169 ), #98284 ) ; +#25078 = FACE_OUTER_BOUND ( 'NONE', #63352, .T. ) ; +#25079 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25080 = PLANE ( 'NONE', #99446 ) ; +#25081 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25083 = ORIENTED_EDGE ( 'NONE', *, *, #72638, .T. ) ; +#25082 = ORIENTED_EDGE ( 'NONE', *, *, #46667, .F. ) ; +#25084 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#25085 = VECTOR ( 'NONE', #92999, 1000.000000000000000 ) ; +#25086 = FILL_AREA_STYLE ('',( #33735 ) ) ; +#25087 = VERTEX_POINT ( 'NONE', #29891 ) ; +#25088 = CARTESIAN_POINT ( 'NONE', ( -0.8380936289687549445, 0.5753100270687899753, 0.8299999999999999600 ) ) ; +#25089 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25091 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25090 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#25092 = ORIENTED_EDGE ( 'NONE', *, *, #34679, .F. ) ; +#25093 = ORIENTED_EDGE ( 'NONE', *, *, #53728, .F. ) ; +#25094 = LINE ( 'NONE', #48565, #13867 ) ; +#25095 = PRESENTATION_STYLE_ASSIGNMENT (( #34256 ) ) ; +#25096 = PLANE ( 'NONE', #57803 ) ; +#25097 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25099 = FACE_OUTER_BOUND ( 'NONE', #87791, .T. ) ; +#25098 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25100 = VERTEX_POINT ( 'NONE', #76356 ) ; +#25101 = ORIENTED_EDGE ( 'NONE', *, *, #4151, .F. ) ; +#25102 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25103 = EDGE_CURVE ( 'NONE', #37734, #50680, #15032, .T. ) ; +#25104 = ORIENTED_EDGE ( 'NONE', *, *, #24064, .F. ) ; +#25105 = EDGE_CURVE ( 'NONE', #5935, #777, #92667, .T. ) ; +#25106 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#25108 = VERTEX_POINT ( 'NONE', #6359 ) ; +#25107 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25109 = LINE ( 'NONE', #56244, #50767 ) ; +#25110 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#25111 = CARTESIAN_POINT ( 'NONE', ( 1.854034869405480013, -1.451435312150680224, 0.8099999999999996092 ) ) ; +#25112 = EDGE_LOOP ( 'NONE', ( #44042, #98642, #42004, #52208 ) ) ; +#25113 = PRESENTATION_STYLE_ASSIGNMENT (( #9171 ) ) ; +#25114 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25115 = ORIENTED_EDGE ( 'NONE', *, *, #31807, .T. ) ; +#25116 = EDGE_CURVE ( 'NONE', #84314, #65755, #68682, .T. ) ; +#25117 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#25118 = EDGE_CURVE ( 'NONE', #62983, #18587, #27522, .T. ) ; +#25119 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25120 = AXIS2_PLACEMENT_3D ( 'NONE', #63444, #55274, #86901 ) ; +#25121 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25122 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#25123 = EDGE_CURVE ( 'NONE', #26486, #64596, #83538, .T. ) ; +#25124 = AXIS2_PLACEMENT_3D ( 'NONE', #90055, #81927, #4779 ) ; +#25125 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13998 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39858, #56209, #86827 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25126 = FILL_AREA_STYLE ('',( #71562 ) ) ; +#25127 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#25128 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.000000000000000000 ) ) ; +#25130 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.149999999999990585, 0.000000000000000000 ) ) ; +#25129 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#25131 = CARTESIAN_POINT ( 'NONE', ( 1.596805013731110279, -1.020192282374009940, 0.8299999999999990719 ) ) ; +#25132 = FACE_OUTER_BOUND ( 'NONE', #15683, .T. ) ; +#25133 = VECTOR ( 'NONE', #56276, 1000.000000000000000 ) ; +#25134 = ORIENTED_EDGE ( 'NONE', *, *, #20109, .F. ) ; +#25135 = DIRECTION ( 'NONE', ( -0.7071067811865470176, 0.7071067811865480168, 0.000000000000000000 ) ) ; +#25136 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#25137 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#25139 = EDGE_CURVE ( 'NONE', #68985, #17448, #99729, .T. ) ; +#25138 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6994 ) ) ; +#25141 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8200000000000000622, 0.1378679656440357226 ) ) ; +#25142 = SURFACE_STYLE_USAGE ( .BOTH. , #95011 ) ; +#25144 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25143 = CARTESIAN_POINT ( 'NONE', ( 0.9685869866146590290, 0.4055590759269659951, 0.8100000000000000533 ) ) ; +#25145 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, 3.149999999999979927, 0.000000000000000000 ) ) ; +#25146 = CARTESIAN_POINT ( 'NONE', ( 3.794707603699269956E-16, 1.393372100993099938, 0.8299999999999999600 ) ) ; +#25147 = EDGE_CURVE ( 'NONE', #93666, #41785, #91671, .T. ) ; +#25148 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83779 ), #8679 ) ; +#25149 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25150 = VECTOR ( 'NONE', #37972, 1000.000000000000000 ) ; +#25151 = EDGE_LOOP ( 'NONE', ( #77399, #86174, #3714, #31826 ) ) ; +#25152 = EDGE_CURVE ( 'NONE', #4568, #16606, #6827, .T. ) ; +#25153 = FACE_OUTER_BOUND ( 'NONE', #22926, .T. ) ; +#25154 = EDGE_CURVE ( 'NONE', #69473, #10257, #52909, .T. ) ; +#25155 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25156 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#25157 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25158 = AXIS2_PLACEMENT_3D ( 'NONE', #40391, #87335, #32217 ) ; +#25159 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25160 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69084, 'distance_accuracy_value', 'NONE'); +#25161 = ORIENTED_EDGE ( 'NONE', *, *, #34452, .F. ) ; +#25162 = LINE ( 'NONE', #1126, #59 ) ; +#25163 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#25164 = FILL_AREA_STYLE_COLOUR ( '', #72186 ) ; +#25165 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25166 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999999778, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#25167 = VECTOR ( 'NONE', #28187, 1000.000000000000000 ) ; +#25168 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90357 ), #65889 ) ; +#25169 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#25170 = SURFACE_STYLE_USAGE ( .BOTH. , #73114 ) ; +#25171 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#25172 = EDGE_CURVE ( 'NONE', #30553, #38466, #21735, .T. ) ; +#25173 = PRESENTATION_STYLE_ASSIGNMENT (( #95046 ) ) ; +#25174 = VERTEX_POINT ( 'NONE', #77356 ) ; +#25175 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69099 ), #35009 ) ; +#25176 = ORIENTED_EDGE ( 'NONE', *, *, #83088, .F. ) ; +#25177 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31333, 'distance_accuracy_value', 'NONE'); +#25178 = SURFACE_SIDE_STYLE ('',( #50173 ) ) ; +#25179 = CYLINDRICAL_SURFACE ( 'NONE', #86859, 0.09999999999999939493 ) ; +#25180 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30010, #76490, #37707, #20363 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#25181 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25182 = SURFACE_STYLE_USAGE ( .BOTH. , #15946 ) ; +#25183 = CARTESIAN_POINT ( 'NONE', ( 0.06941959667897069919, -1.084027901463999966, 0.8100000000000000533 ) ) ; +#25184 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96855 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32725, #1581, #87838 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25185 = VERTEX_POINT ( 'NONE', #38571 ) ; +#25186 = CYLINDRICAL_SURFACE ( 'NONE', #18328, 0.09999999999999999167 ) ; +#25187 = EDGE_CURVE ( 'NONE', #52560, #5131, #4647, .T. ) ; +#25188 = SURFACE_STYLE_FILL_AREA ( #48657 ) ; +#25189 = ORIENTED_EDGE ( 'NONE', *, *, #11302, .T. ) ; +#25190 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25191 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61026 ) ) ; +#25192 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25193 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#25194 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#25195 = ORIENTED_EDGE ( 'NONE', *, *, #84620, .F. ) ; +#25196 = ADVANCED_FACE ( 'NONE', ( #83036 ), #60090, .T. ) ; +#25197 = VECTOR ( 'NONE', #5135, 1000.000000000000000 ) ; +#25198 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#25199 = FILL_AREA_STYLE_COLOUR ( '', #61554 ) ; +#25200 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, -3.500000000000000444, 0.000000000000000000 ) ) ; +#25201 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#25202 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43084 ) ) ; +#25203 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.549999999999999822, 0.000000000000000000 ) ) ; +#25204 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25205 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99810 ) ) ; +#25206 = EDGE_LOOP ( 'NONE', ( #49162, #35224, #73180, #71277 ) ) ; +#25207 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25208 = LINE ( 'NONE', #34372, #38130 ) ; +#25209 = ORIENTED_EDGE ( 'NONE', *, *, #84354, .F. ) ; +#25210 = FACE_OUTER_BOUND ( 'NONE', #62627, .T. ) ; +#25211 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25212 = VECTOR ( 'NONE', #25646, 1000.000000000000000 ) ; +#25213 = CARTESIAN_POINT ( 'NONE', ( 0.4344096565324859771, -0.9919132076701281386, 0.8300000000000002931 ) ) ; +#25214 = ORIENTED_EDGE ( 'NONE', *, *, #43962, .F. ) ; +#25217 = VECTOR ( 'NONE', #27777, 1000.000000000000000 ) ; +#25216 = AXIS2_PLACEMENT_3D ( 'NONE', #95215, #71266, #40144 ) ; +#25215 = FILL_AREA_STYLE_COLOUR ( '', #36693 ) ; +#25218 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25219 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25220 = VECTOR ( 'NONE', #59703, 1000.000000000000000 ) ; +#25221 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#25223 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67363 ) ) ; +#25222 = SURFACE_SIDE_STYLE ('',( #31824 ) ) ; +#25224 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25225 = SURFACE_SIDE_STYLE ('',( #9272 ) ) ; +#25226 = ORIENTED_EDGE ( 'NONE', *, *, #59825, .F. ) ; +#25228 = ORIENTED_EDGE ( 'NONE', *, *, #97694, .F. ) ; +#25227 = VERTEX_POINT ( 'NONE', #70198 ) ; +#25229 = SURFACE_STYLE_USAGE ( .BOTH. , #678 ) ; +#25230 = AXIS2_PLACEMENT_3D ( 'NONE', #100442, #30590, #61798 ) ; +#25231 = ORIENTED_EDGE ( 'NONE', *, *, #67683, .T. ) ; +#25232 = EDGE_CURVE ( 'NONE', #75028, #30758, #87557, .T. ) ; +#25233 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87147 ) ) ; +#25234 = EDGE_LOOP ( 'NONE', ( #93794, #85340, #25704, #31479 ) ) ; +#25236 = ORIENTED_EDGE ( 'NONE', *, *, #98552, .T. ) ; +#25235 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 1.076179938779915135, 0.000000000000000000 ) ) ; +#25237 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25239 = FILL_AREA_STYLE ('',( #64002 ) ) ; +#25238 = LINE ( 'NONE', #55848, #77006 ) ; +#25240 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25241 = VERTEX_POINT ( 'NONE', #15553 ) ; +#25242 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25243 = VERTEX_POINT ( 'NONE', #24805 ) ; +#25244 = FACE_OUTER_BOUND ( 'NONE', #64628, .T. ) ; +#25245 = FACE_OUTER_BOUND ( 'NONE', #30047, .T. ) ; +#25246 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25247 = VERTEX_POINT ( 'NONE', #95177 ) ; +#25248 = ORIENTED_EDGE ( 'NONE', *, *, #70755, .T. ) ; +#25249 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46323 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6762, #21673, #53330 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25250 = SURFACE_STYLE_FILL_AREA ( #42046 ) ; +#25252 = FACE_OUTER_BOUND ( 'NONE', #72653, .T. ) ; +#25251 = SURFACE_STYLE_FILL_AREA ( #96131 ) ; +#25253 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#25254 = AXIS2_PLACEMENT_3D ( 'NONE', #68651, #99700, #22208 ) ; +#25255 = FILL_AREA_STYLE_COLOUR ( '', #53202 ) ; +#25256 = STYLED_ITEM ( 'NONE', ( #88901 ), #53835 ) ; +#25257 = FILL_AREA_STYLE_COLOUR ( '', #90161 ) ; +#25258 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.000000000000000000 ) ) ; +#25259 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83933 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90148, #34571, #20204 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25260 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#25261 = VERTEX_POINT ( 'NONE', #41117 ) ; +#25262 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74145 ) ) ; +#25263 = CARTESIAN_POINT ( 'NONE', ( -0.5238200612200851758, 3.099999999999989875, 0.000000000000000000 ) ) ; +#25264 = LINE ( 'NONE', #93611, #51632 ) ; +#25265 = ORIENTED_EDGE ( 'NONE', *, *, #75544, .F. ) ; +#25266 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25267 = FILL_AREA_STYLE ('',( #41574 ) ) ; +#25268 = VECTOR ( 'NONE', #79558, 1000.000000000000000 ) ; +#25269 = EDGE_CURVE ( 'NONE', #1862, #81673, #42712, .T. ) ; +#25271 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25270 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#25272 = LINE ( 'NONE', #32903, #58633 ) ; +#25273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24515, 'distance_accuracy_value', 'NONE'); +#25274 = SURFACE_STYLE_FILL_AREA ( #24258 ) ; +#25275 = VECTOR ( 'NONE', #7834, 1000.000000000000000 ) ; +#25276 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#25277 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.383333333333333304, 0.000000000000000000 ) ) ; +#25278 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.600000000000000089, -11.57000000000000028 ) ) ; +#25279 = AXIS2_PLACEMENT_3D ( 'NONE', #57194, #42363, #65316 ) ; +#25280 = VERTEX_POINT ( 'NONE', #56455 ) ; +#25281 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25282 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25283 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#25286 = STYLED_ITEM ( 'NONE', ( #15759 ), #27141 ) ; +#25285 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24675 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46112, #54325, #76282 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25284 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25287 = STYLED_ITEM ( 'NONE', ( #29388 ), #98725 ) ; +#25288 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, -3.149999999999990585, 0.000000000000000000 ) ) ; +#25289 = FILL_AREA_STYLE ('',( #78865 ) ) ; +#25290 = FACE_OUTER_BOUND ( 'NONE', #56215, .T. ) ; +#25291 = PLANE ( 'NONE', #51761 ) ; +#25292 = FILL_AREA_STYLE_COLOUR ( '', #15776 ) ; +#25293 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83925 ), #17072 ) ; +#25294 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25295 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#25296 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999990319, -0.02000000000000000042 ) ) ; +#25297 = ORIENTED_EDGE ( 'NONE', *, *, #6882, .T. ) ; +#25298 = EDGE_LOOP ( 'NONE', ( #75402, #59992, #83826, #30388, #95957, #20659 ) ) ; +#25299 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12129 ), #41676 ) ; +#25300 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#25301 = CARTESIAN_POINT ( 'NONE', ( 0.1831366936980619864, -1.373561790606270039, 0.8299999999999999600 ) ) ; +#25302 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.437662337662340084, 0.8299999999999999600 ) ) ; +#25303 = SURFACE_STYLE_FILL_AREA ( #48781 ) ; +#25304 = SURFACE_STYLE_USAGE ( .BOTH. , #2313 ) ; +#25305 = EDGE_LOOP ( 'NONE', ( #100628, #58854, #82102, #44112 ) ) ; +#25306 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#25307 = EDGE_CURVE ( 'NONE', #28287, #73618, #72234, .T. ) ; +#25308 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61818, #5375, #66203, #35086 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#25309 = SURFACE_STYLE_FILL_AREA ( #96696 ) ; +#25310 = ORIENTED_EDGE ( 'NONE', *, *, #62117, .T. ) ; +#25311 = STYLED_ITEM ( 'NONE', ( #100539 ), #72601 ) ; +#25312 = FACE_OUTER_BOUND ( 'NONE', #20377, .T. ) ; +#25313 = SURFACE_STYLE_USAGE ( .BOTH. , #88566 ) ; +#25314 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25315 = VECTOR ( 'NONE', #64049, 1000.000000000000000 ) ; +#25316 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#25317 = EDGE_CURVE ( 'NONE', #13067, #78320, #86036, .T. ) ; +#25318 = ORIENTED_EDGE ( 'NONE', *, *, #84028, .F. ) ; +#25319 = SURFACE_STYLE_USAGE ( .BOTH. , #79935 ) ; +#25320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18114, 'distance_accuracy_value', 'NONE'); +#25321 = LINE ( 'NONE', #85165, #36382 ) ; +#25322 = FILL_AREA_STYLE_COLOUR ( '', #42602 ) ; +#25323 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96977 ), #70914 ) ; +#25324 = ADVANCED_FACE ( 'NONE', ( #48779 ), #78388, .T. ) ; +#25325 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#25326 = ORIENTED_EDGE ( 'NONE', *, *, #63828, .F. ) ; +#25327 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100168 ) ) ; +#25328 = SURFACE_STYLE_FILL_AREA ( #81470 ) ; +#25329 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#25330 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#25331 = AXIS2_PLACEMENT_3D ( 'NONE', #94093, #8777, #9791 ) ; +#25332 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25333 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25334 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#25335 = PLANE ( 'NONE', #36805 ) ; +#25336 = EDGE_CURVE ( 'NONE', #21763, #11603, #79406, .T. ) ; +#25337 = EDGE_CURVE ( 'NONE', #72636, #51979, #79920, .T. ) ; +#25338 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90458 ) ) ; +#25339 = EDGE_CURVE ( 'NONE', #15430, #72098, #23265, .T. ) ; +#25340 = ORIENTED_EDGE ( 'NONE', *, *, #90240, .T. ) ; +#25341 = ADVANCED_FACE ( 'NONE', ( #33965 ), #80414, .F. ) ; +#25343 = VERTEX_POINT ( 'NONE', #97200 ) ; +#25342 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25345 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1996 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37944, #62962, #85399 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25344 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84946, 'distance_accuracy_value', 'NONE'); +#25346 = SURFACE_STYLE_FILL_AREA ( #33495 ) ; +#25347 = CARTESIAN_POINT ( 'NONE', ( -5.000849739953540302E-06, 1.393332985365729915, 0.8100000000000000533 ) ) ; +#25348 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25349 = ORIENTED_EDGE ( 'NONE', *, *, #87671, .T. ) ; +#25350 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25351 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14407 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87986, #32863, #62504 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25352 = EDGE_CURVE ( 'NONE', #68821, #79084, #63925, .T. ) ; +#25353 = VECTOR ( 'NONE', #91653, 1000.000000000000000 ) ; +#25354 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25355 = ORIENTED_EDGE ( 'NONE', *, *, #36936, .F. ) ; +#25357 = FACE_OUTER_BOUND ( 'NONE', #85112, .T. ) ; +#25356 = DIRECTION ( 'NONE', ( -0.7071067806865475314, -0.7071067816865476141, 0.000000000000000000 ) ) ; +#25358 = ORIENTED_EDGE ( 'NONE', *, *, #79843, .T. ) ; +#25359 = ORIENTED_EDGE ( 'NONE', *, *, #12552, .T. ) ; +#25360 = FILL_AREA_STYLE ('',( #80470 ) ) ; +#25361 = EDGE_CURVE ( 'NONE', #89490, #86944, #42112, .T. ) ; +#25362 = AXIS2_PLACEMENT_3D ( 'NONE', #75830, #21201, #59050 ) ; +#25363 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999997446, 1.174118672656968804E-15, 0.8499999999999999778 ) ) ; +#25364 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25365 = ORIENTED_EDGE ( 'NONE', *, *, #34504, .F. ) ; +#25366 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12205 ), #7308 ) ; +#25367 = FILL_AREA_STYLE_COLOUR ( '', #54832 ) ; +#25368 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#25369 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#25370 = ORIENTED_EDGE ( 'NONE', *, *, #68572, .F. ) ; +#25371 = CARTESIAN_POINT ( 'NONE', ( 1.350478891332010267, -1.390055052842650074, 0.8100000000000000533 ) ) ; +#25372 = EDGE_LOOP ( 'NONE', ( #83335, #5776, #15804, #72380, #44024, #53950 ) ) ; +#25373 = ORIENTED_EDGE ( 'NONE', *, *, #43620, .F. ) ; +#25374 = PRESENTATION_STYLE_ASSIGNMENT (( #63166 ) ) ; +#25375 = LINE ( 'NONE', #17656, #46838 ) ; +#25376 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25377 = LINE ( 'NONE', #88629, #80756 ) ; +#25378 = PLANE ( 'NONE', #10287 ) ; +#25379 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25380 = ORIENTED_EDGE ( 'NONE', *, *, #24302, .F. ) ; +#25381 = DIRECTION ( 'NONE', ( 0.7071067811865470176, 0.7071067811865480168, 0.000000000000000000 ) ) ; +#25382 = LINE ( 'NONE', #78972, #44781 ) ; +#25383 = ADVANCED_FACE ( 'NONE', ( #26800 ), #61108, .F. ) ; +#25385 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25384 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25386 = SURFACE_STYLE_USAGE ( .BOTH. , #3877 ) ; +#25387 = FILL_AREA_STYLE_COLOUR ( '', #94013 ) ; +#25388 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#25389 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61240 ) ) ; +#25390 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18778 ) ) ; +#25391 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27061 ) ) ; +#25392 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000002623, -0.1350000000000000089 ) ) ; +#25393 = EDGE_CURVE ( 'NONE', #38757, #52472, #45072, .T. ) ; +#25394 = ORIENTED_EDGE ( 'NONE', *, *, #51412, .T. ) ; +#25395 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54771 ), #13856 ) ; +#25396 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#25398 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59150, 'distance_accuracy_value', 'NONE'); +#25397 = FILL_AREA_STYLE_COLOUR ( '', #18397 ) ; +#25399 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25400 = AXIS2_PLACEMENT_3D ( 'NONE', #37632, #14086, #92222 ) ; +#25401 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25402 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25403 = STYLED_ITEM ( 'NONE', ( #22949 ), #78382 ) ; +#25405 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27073 ), #93824 ) ; +#25404 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#25406 = SURFACE_SIDE_STYLE ('',( #2406 ) ) ; +#25407 = FILL_AREA_STYLE_COLOUR ( '', #78807 ) ; +#25408 = FILL_AREA_STYLE_COLOUR ( '', #30344 ) ; +#25409 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25411 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8648700000000000276 ) ) ; +#25410 = AXIS2_PLACEMENT_3D ( 'NONE', #41404, #3595, #57753 ) ; +#25412 = FILL_AREA_STYLE_COLOUR ( '', #7911 ) ; +#25413 = FILL_AREA_STYLE_COLOUR ( '', #91035 ) ; +#25414 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25415 = AXIS2_PLACEMENT_3D ( 'NONE', #39957, #18970, #55792 ) ; +#25416 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25417 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25418 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#25419 = EDGE_LOOP ( 'NONE', ( #4905, #63292, #59488, #57713 ) ) ; +#25420 = FACE_OUTER_BOUND ( 'NONE', #79580, .T. ) ; +#25421 = EDGE_CURVE ( 'NONE', #91498, #59345, #29771, .T. ) ; +#25422 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25423 = AXIS2_PLACEMENT_3D ( 'NONE', #49083, #89865, #51097 ) ; +#25424 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100259 ), #7299 ) ; +#25425 = SURFACE_STYLE_FILL_AREA ( #1415 ) ; +#25426 = SURFACE_STYLE_USAGE ( .BOTH. , #89198 ) ; +#25427 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25428 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, 3.099999999999969891, 0.000000000000000000 ) ) ; +#25429 = AXIS2_PLACEMENT_3D ( 'NONE', #66867, #13686, #37267 ) ; +#25430 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25431 = ORIENTED_EDGE ( 'NONE', *, *, #49501, .F. ) ; +#25432 = SURFACE_STYLE_FILL_AREA ( #95823 ) ; +#25433 = CARTESIAN_POINT ( 'NONE', ( -0.3684964207368675582, -0.9618530369151632176, 0.8099999999998250821 ) ) ; +#25434 = FILL_AREA_STYLE_COLOUR ( '', #34201 ) ; +#25435 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25436 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4808578643762691507, 0.2434314575050761653 ) ) ; +#25437 = ADVANCED_FACE ( 'NONE', ( #60464 ), #6711, .T. ) ; +#25438 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25439 = VERTEX_POINT ( 'NONE', #52291 ) ; +#25440 = VERTEX_POINT ( 'NONE', #36456 ) ; +#25441 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25442 = LINE ( 'NONE', #42748, #60521 ) ; +#25443 = VERTEX_POINT ( 'NONE', #98152 ) ; +#25444 = STYLED_ITEM ( 'NONE', ( #32001 ), #73274 ) ; +#25445 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25446 = SURFACE_STYLE_USAGE ( .BOTH. , #24955 ) ; +#25447 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #28630 ) ; +#25448 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#25449 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80919 ) ) ; +#25451 = ORIENTED_EDGE ( 'NONE', *, *, #96902, .T. ) ; +#25450 = ORIENTED_EDGE ( 'NONE', *, *, #58979, .T. ) ; +#25452 = ORIENTED_EDGE ( 'NONE', *, *, #45947, .F. ) ; +#25453 = EDGE_CURVE ( 'NONE', #71780, #10043, #37956, .T. ) ; +#25454 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#25455 = VECTOR ( 'NONE', #54993, 999.9999999999998863 ) ; +#25456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90162, 'distance_accuracy_value', 'NONE'); +#25457 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89076 ), #67819 ) ; +#25459 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25458 = SURFACE_SIDE_STYLE ('',( #49427 ) ) ; +#25460 = EDGE_LOOP ( 'NONE', ( #94389, #100887, #54199, #15451 ) ) ; +#25461 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49953 ) ) ; +#25462 = LINE ( 'NONE', #25971, #96190 ) ; +#25463 = VECTOR ( 'NONE', #92110, 1000.000000000000000 ) ; +#25464 = EDGE_LOOP ( 'NONE', ( #54593, #13804, #55188, #95998 ) ) ; +#25465 = VERTEX_POINT ( 'NONE', #84901 ) ; +#25466 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25467 = CARTESIAN_POINT ( 'NONE', ( 0.6702516233766231402, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#25468 = VERTEX_POINT ( 'NONE', #28292 ) ; +#25469 = ORIENTED_EDGE ( 'NONE', *, *, #35400, .T. ) ; +#25470 = CARTESIAN_POINT ( 'NONE', ( 0.2365201132049190025, -1.424034756619420028, 0.8300000000000004041 ) ) ; +#25471 = ADVANCED_FACE ( 'NONE', ( #46064 ), #77237, .T. ) ; +#25472 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10629 ), #72682 ) ; +#25473 = LINE ( 'NONE', #17762, #42415 ) ; +#25474 = STYLED_ITEM ( 'NONE', ( #14245 ), #61845 ) ; +#25475 = EDGE_LOOP ( 'NONE', ( #45609, #5948, #63888, #20923, #81847, #32321 ) ) ; +#25476 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.499999999999980016, 0.1829999999999999960 ) ) ; +#25477 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25478 = PRESENTATION_STYLE_ASSIGNMENT (( #25988 ) ) ; +#25479 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 0.4500000000000001221 ) ) ; +#25480 = EDGE_LOOP ( 'NONE', ( #64810, #87619, #73807, #16017 ) ) ; +#25482 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25481 = SURFACE_SIDE_STYLE ('',( #49980 ) ) ; +#25483 = FACE_OUTER_BOUND ( 'NONE', #49710, .T. ) ; +#25484 = ORIENTED_EDGE ( 'NONE', *, *, #55204, .F. ) ; +#25485 = VERTEX_POINT ( 'NONE', #32812 ) ; +#25487 = LINE ( 'NONE', #48472, #25979 ) ; +#25486 = SURFACE_SIDE_STYLE ('',( #1989 ) ) ; +#25488 = CARTESIAN_POINT ( 'NONE', ( 1.807266337641940002, -1.389839611604140046, 0.8300000000000002931 ) ) ; +#25489 = VECTOR ( 'NONE', #76425, 1000.000000000000000 ) ; +#25490 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25491 = VECTOR ( 'NONE', #98992, 1000.000000000000000 ) ; +#25492 = LINE ( 'NONE', #71941, #59660 ) ; +#25493 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999994, 0.8648700000000000276 ) ) ; +#25494 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25495 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38790, 'distance_accuracy_value', 'NONE'); +#25496 = VECTOR ( 'NONE', #51830, 1000.000000000000000 ) ; +#25497 = ADVANCED_FACE ( 'NONE', ( #86941 ), #54287, .T. ) ; +#25498 = LINE ( 'NONE', #71436, #11549 ) ; +#25499 = EDGE_LOOP ( 'NONE', ( #23318, #100427, #87595, #27434 ) ) ; +#25500 = CARTESIAN_POINT ( 'NONE', ( 0.3814764115086780039, -1.210722004796850104, 0.8299999999999999600 ) ) ; +#25501 = FILL_AREA_STYLE_COLOUR ( '', #12004 ) ; +#25502 = ORIENTED_EDGE ( 'NONE', *, *, #97016, .F. ) ; +#25503 = AXIS2_PLACEMENT_3D ( 'NONE', #35530, #49845, #97255 ) ; +#25504 = FACE_OUTER_BOUND ( 'NONE', #40914, .T. ) ; +#25505 = FILL_AREA_STYLE ('',( #472 ) ) ; +#25506 = FACE_OUTER_BOUND ( 'NONE', #76135, .T. ) ; +#25507 = FILL_AREA_STYLE ('',( #88779 ) ) ; +#25508 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999460114 ) ) ; +#25509 = EDGE_CURVE ( 'NONE', #89578, #23403, #37289, .T. ) ; +#25510 = FACE_OUTER_BOUND ( 'NONE', #81218, .T. ) ; +#25511 = CARTESIAN_POINT ( 'NONE', ( 1.662784294148539344, -1.164927051866629482, 0.8300000000000000711 ) ) ; +#25512 = SURFACE_STYLE_FILL_AREA ( #40323 ) ; +#25513 = CARTESIAN_POINT ( 'NONE', ( 0.3533189038523930070, -0.9001815241100280529, 0.8100000000000000533 ) ) ; +#25514 = SURFACE_STYLE_USAGE ( .BOTH. , #25020 ) ; +#25515 = FILL_AREA_STYLE_COLOUR ( '', #17943 ) ; +#25516 = AXIS2_PLACEMENT_3D ( 'NONE', #9189, #86886, #48607 ) ; +#25517 = LINE ( 'NONE', #85252, #54905 ) ; +#25518 = FILL_AREA_STYLE ('',( #16790 ) ) ; +#25519 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17311 ), #89130 ) ; +#25520 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25521 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.700000000000000178, 1.158998207294579771E-78 ) ) ; +#25522 = SURFACE_STYLE_USAGE ( .BOTH. , #32162 ) ; +#25523 = FILL_AREA_STYLE_COLOUR ( '', #20776 ) ; +#25524 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#25525 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #74155, #74668, #73155, #58873 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#25526 = VECTOR ( 'NONE', #33039, 1000.000000000000000 ) ; +#25527 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74342 ) ) ; +#25528 = ORIENTED_EDGE ( 'NONE', *, *, #87724, .T. ) ; +#25529 = CARTESIAN_POINT ( 'NONE', ( 1.512057002305370101, -1.084890943604200020, 0.8299999999999999600 ) ) ; +#25530 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44299, 'distance_accuracy_value', 'NONE'); +#25531 = VERTEX_POINT ( 'NONE', #100596 ) ; +#25532 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11698, 'distance_accuracy_value', 'NONE'); +#25533 = EDGE_CURVE ( 'NONE', #36985, #45870, #42976, .T. ) ; +#25535 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25534 = FILL_AREA_STYLE ('',( #88310 ) ) ; +#25536 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#25538 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999996225, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#25537 = STYLED_ITEM ( 'NONE', ( #83485 ), #78801 ) ; +#25539 = VECTOR ( 'NONE', #50941, 1000.000000000000000 ) ; +#25540 = SURFACE_STYLE_FILL_AREA ( #41854 ) ; +#25541 = EDGE_CURVE ( 'NONE', #93165, #35982, #11734, .T. ) ; +#25542 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100945 ) ; +#25543 = VERTEX_POINT ( 'NONE', #50670 ) ; +#25544 = VERTEX_POINT ( 'NONE', #41486 ) ; +#25545 = SURFACE_STYLE_USAGE ( .BOTH. , #4045 ) ; +#25546 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90960, 'distance_accuracy_value', 'NONE'); +#25547 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146560143, 0.2541340759269650196, 0.8299999999999999600 ) ) ; +#25548 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.000000000000000000, 0.4500000000000001221 ) ) ; +#25549 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25550 = SURFACE_SIDE_STYLE ('',( #7591 ) ) ; +#25551 = FILL_AREA_STYLE ('',( #3057 ) ) ; +#25552 = FACE_OUTER_BOUND ( 'NONE', #50449, .T. ) ; +#25553 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25554 = ORIENTED_EDGE ( 'NONE', *, *, #69370, .T. ) ; +#25555 = EDGE_CURVE ( 'NONE', #26854, #89492, #14056, .T. ) ; +#25556 = SURFACE_STYLE_FILL_AREA ( #57211 ) ; +#25557 = EDGE_CURVE ( 'NONE', #54178, #23149, #2681, .T. ) ; +#25558 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25559 = ORIENTED_EDGE ( 'NONE', *, *, #96146, .F. ) ; +#25560 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#25561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82166 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84035, #14031, #75863 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25562 = FILL_AREA_STYLE ('',( #64343 ) ) ; +#25563 = VERTEX_POINT ( 'NONE', #88951 ) ; +#25564 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25565 = SURFACE_STYLE_FILL_AREA ( #25073 ) ; +#25566 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#25567 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97301 ), #74541 ) ; +#25568 = DIRECTION ( 'NONE', ( 6.123031769111889989E-17, 1.000000000000000000, 0.000000000000000000 ) ) ; +#25569 = SURFACE_STYLE_FILL_AREA ( #95460 ) ; +#25570 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25572 = VERTEX_POINT ( 'NONE', #25660 ) ; +#25571 = EDGE_LOOP ( 'NONE', ( #29808, #23670, #79302, #95566 ) ) ; +#25573 = FILL_AREA_STYLE_COLOUR ( '', #94700 ) ; +#25574 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#25575 = VERTEX_POINT ( 'NONE', #35359 ) ; +#25577 = EDGE_CURVE ( 'NONE', #21935, #46484, #16609, .T. ) ; +#25576 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25578 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#25580 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25579 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#25581 = VERTEX_POINT ( 'NONE', #73127 ) ; +#25582 = EDGE_LOOP ( 'NONE', ( #85469, #82281, #585, #88832 ) ) ; +#25583 = FILL_AREA_STYLE ('',( #95473 ) ) ; +#25584 = CARTESIAN_POINT ( 'NONE', ( -0.1181104512869620010, -0.9624218420162741205, 0.8300000000000000711 ) ) ; +#25586 = LINE ( 'NONE', #3089, #98700 ) ; +#25585 = FILL_AREA_STYLE ('',( #57757 ) ) ; +#25587 = ORIENTED_EDGE ( 'NONE', *, *, #2651, .T. ) ; +#25588 = ORIENTED_EDGE ( 'NONE', *, *, #69594, .T. ) ; +#25589 = DIRECTION ( 'NONE', ( 0.7071067811865479058, -0.7071067811865470176, 0.000000000000000000 ) ) ; +#25590 = VERTEX_POINT ( 'NONE', #2180 ) ; +#25591 = PRESENTATION_STYLE_ASSIGNMENT (( #71542 ) ) ; +#25592 = ADVANCED_FACE ( 'NONE', ( #41994 ), #64958, .T. ) ; +#25593 = VECTOR ( 'NONE', #71448, 1000.000000000000000 ) ; +#25595 = EDGE_LOOP ( 'NONE', ( #95978, #59234, #96441, #61292 ) ) ; +#25594 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#25596 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#25597 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7546 ), #76074 ) ; +#25598 = AXIS2_PLACEMENT_3D ( 'NONE', #33677, #2520, #2014 ) ; +#25599 = PRESENTATION_STYLE_ASSIGNMENT (( #48583 ) ) ; +#25600 = ORIENTED_EDGE ( 'NONE', *, *, #40287, .T. ) ; +#25601 = DIRECTION ( 'NONE', ( 4.344024262657780003E-34, 4.266452400824600274E-34, 1.000000000000000000 ) ) ; +#25602 = VERTEX_POINT ( 'NONE', #11239 ) ; +#25603 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22066 ) ) ; +#25604 = SURFACE_STYLE_USAGE ( .BOTH. , #27119 ) ; +#25605 = PRESENTATION_STYLE_ASSIGNMENT (( #41428 ) ) ; +#25606 = EDGE_CURVE ( 'NONE', #69987, #31406, #34850, .T. ) ; +#25607 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#25608 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#25610 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.4999999999999993339, 5.608055841774961276E-79 ) ) ; +#25609 = STYLED_ITEM ( 'NONE', ( #99761 ), #16972 ) ; +#25611 = EDGE_CURVE ( 'NONE', #27175, #71466, #72122, .T. ) ; +#25612 = DIRECTION ( 'NONE', ( -0.7071062811868787934, -0.7071072811858626350, 0.000000000000000000 ) ) ; +#25613 = ORIENTED_EDGE ( 'NONE', *, *, #2334, .F. ) ; +#25614 = EDGE_LOOP ( 'NONE', ( #17335, #93200, #81199, #28058 ) ) ; +#25615 = SURFACE_SIDE_STYLE ('',( #87881 ) ) ; +#25616 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#25617 = FACE_OUTER_BOUND ( 'NONE', #93441, .T. ) ; +#25618 = VECTOR ( 'NONE', #69150, 1000.000000000000000 ) ; +#25619 = VECTOR ( 'NONE', #46464, 1000.000000000000114 ) ; +#25620 = FILL_AREA_STYLE_COLOUR ( '', #99962 ) ; +#25621 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25622 = CLOSED_SHELL ( 'NONE', ( #14482, #10193, #70635, #47045, #68296, #59568 ) ) ; +#25623 = ADVANCED_FACE ( 'NONE', ( #19494 ), #89935, .T. ) ; +#25624 = VECTOR ( 'NONE', #99348, 1000.000000000000114 ) ; +#25625 = STYLED_ITEM ( 'NONE', ( #11240 ), #100110 ) ; +#25626 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, -0.1499999999999999944 ) ) ; +#25627 = STYLED_ITEM ( 'NONE', ( #71501 ), #5794 ) ; +#25628 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25629 = SURFACE_STYLE_FILL_AREA ( #9705 ) ; +#25630 = STYLED_ITEM ( 'NONE', ( #44509 ), #14397 ) ; +#25631 = ORIENTED_EDGE ( 'NONE', *, *, #54555, .T. ) ; +#25632 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#25633 = SURFACE_STYLE_USAGE ( .BOTH. , #16403 ) ; +#25634 = FILL_AREA_STYLE_COLOUR ( '', #64988 ) ; +#25635 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25636 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#25637 = VERTEX_POINT ( 'NONE', #36332 ) ; +#25638 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25639 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25640 = CARTESIAN_POINT ( 'NONE', ( -1.056478722217069954, -0.9834456900322131601, 0.8299999999999999600 ) ) ; +#25641 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#25642 = LINE ( 'NONE', #18963, #29012 ) ; +#25644 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#25643 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17478, #79804, #95574 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25645 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.000000000000000000 ) ) ; +#25646 = DIRECTION ( 'NONE', ( -0.7071067811865485719, -0.7071067811865465735, 0.000000000000000000 ) ) ; +#25647 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999620541 ) ) ; +#25648 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34375, 'distance_accuracy_value', 'NONE'); +#25649 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25650 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25651 = VERTEX_POINT ( 'NONE', #21007 ) ; +#25652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25653 = ORIENTED_EDGE ( 'NONE', *, *, #75068, .F. ) ; +#25654 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#25655 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20454, 'distance_accuracy_value', 'NONE'); +#25656 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #476, 'distance_accuracy_value', 'NONE'); +#25657 = PLANE ( 'NONE', #56380 ) ; +#25658 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#25659 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25660 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4849999999999999867, 0.2399999999999999911 ) ) ; +#25661 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.01499999999999999944, 0.2399999999999999911 ) ) ; +#25662 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25663 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25664 = EDGE_LOOP ( 'NONE', ( #40401, #3103, #41669, #3479 ) ) ; +#25665 = EDGE_CURVE ( 'NONE', #45093, #2623, #30137, .T. ) ; +#25667 = CARTESIAN_POINT ( 'NONE', ( 1.476179938779914602, 3.099999999999970335, 0.000000000000000000 ) ) ; +#25666 = AXIS2_PLACEMENT_3D ( 'NONE', #96680, #88050, #79903 ) ; +#25668 = EDGE_CURVE ( 'NONE', #48290, #52467, #12763, .T. ) ; +#25669 = ORIENTED_EDGE ( 'NONE', *, *, #37803, .F. ) ; +#25670 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#25671 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25672 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#25673 = VERTEX_POINT ( 'NONE', #43977 ) ; +#25674 = ADVANCED_FACE ( 'NONE', ( #6114 ), #4661, .T. ) ; +#25675 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25676 = PLANE ( 'NONE', #38112 ) ; +#25677 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67818 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1313, #64117, #12046 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25678 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25679 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#25681 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#25680 = VECTOR ( 'NONE', #10332, 1000.000000000000000 ) ; +#25682 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#25683 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86001 ) ) ; +#25684 = ORIENTED_EDGE ( 'NONE', *, *, #7783, .T. ) ; +#25685 = ORIENTED_EDGE ( 'NONE', *, *, #21277, .F. ) ; +#25686 = EDGE_CURVE ( 'NONE', #78546, #14748, #5630, .T. ) ; +#25687 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25688 = CLOSED_SHELL ( 'NONE', ( #35007, #65068, #96229, #65897, #26646, #12637 ) ) ; +#25689 = EDGE_LOOP ( 'NONE', ( #83124, #47905, #55213, #46259 ) ) ; +#25690 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46058 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39053, #7311, #29381 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25691 = ADVANCED_FACE ( 'NONE', ( #61343 ), #13773, .T. ) ; +#25692 = CIRCLE ( 'NONE', #33866, 0.2500000000000000000 ) ; +#25693 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25694 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25695 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#25696 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25697 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25698 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#25700 = VERTEX_POINT ( 'NONE', #20491 ) ; +#25699 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25702 = ORIENTED_EDGE ( 'NONE', *, *, #93678, .T. ) ; +#25701 = ORIENTED_EDGE ( 'NONE', *, *, #92165, .T. ) ; +#25703 = FACE_OUTER_BOUND ( 'NONE', #50931, .T. ) ; +#25704 = ORIENTED_EDGE ( 'NONE', *, *, #39708, .F. ) ; +#25705 = VECTOR ( 'NONE', #89373, 1000.000000000000000 ) ; +#25706 = CARTESIAN_POINT ( 'NONE', ( 1.826762951391289969, -1.165682221622120096, 0.8299999999999995159 ) ) ; +#25707 = ADVANCED_FACE ( 'NONE', ( #52655 ), #44950, .T. ) ; +#25708 = ORIENTED_EDGE ( 'NONE', *, *, #76593, .T. ) ; +#25710 = ORIENTED_EDGE ( 'NONE', *, *, #60172, .T. ) ; +#25709 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 8.003631000000000384, 0.8648700000000000276 ) ) ; +#25711 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#25713 = SURFACE_STYLE_FILL_AREA ( #95607 ) ; +#25712 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25715 = ORIENTED_EDGE ( 'NONE', *, *, #53266, .T. ) ; +#25716 = LINE ( 'NONE', #18003, #29346 ) ; +#25717 = CARTESIAN_POINT ( 'NONE', ( 1.697893922398610034, -1.445363849546990265, 0.8099999999999997202 ) ) ; +#25718 = SURFACE_STYLE_USAGE ( .BOTH. , #19545 ) ; +#25719 = ORIENTED_EDGE ( 'NONE', *, *, #64377, .F. ) ; +#25720 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #79314 ) ) ; +#25721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25722 = SURFACE_SIDE_STYLE ('',( #63023 ) ) ; +#25723 = PRESENTATION_STYLE_ASSIGNMENT (( #95111 ) ) ; +#25724 = PRESENTATION_STYLE_ASSIGNMENT (( #1738 ) ) ; +#25725 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97428 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28189, #78165, #86313 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25726 = ORIENTED_EDGE ( 'NONE', *, *, #65206, .F. ) ; +#25727 = AXIS2_PLACEMENT_3D ( 'NONE', #85833, #30681, #38383 ) ; +#25728 = LINE ( 'NONE', #35417, #58477 ) ; +#25729 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25730 = PRESENTATION_STYLE_ASSIGNMENT (( #64018 ) ) ; +#25731 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12590 ) ) ; +#25732 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#25733 = EDGE_CURVE ( 'NONE', #80334, #92428, #85279, .T. ) ; +#25734 = PLANE ( 'NONE', #39116 ) ; +#25735 = FILL_AREA_STYLE ('',( #63543 ) ) ; +#25736 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69714 ) ) ; +#25737 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#25738 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#25739 = PLANE ( 'NONE', #9863 ) ; +#25740 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25741 = ADVANCED_FACE ( 'NONE', ( #71492 ), #515, .F. ) ; +#25742 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56807 ), #27414 ) ; +#25743 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48569 ) ) ; +#25745 = EDGE_CURVE ( 'NONE', #96986, #47287, #63848, .T. ) ; +#25744 = CARTESIAN_POINT ( 'NONE', ( 1.137126380867480080, -0.8900438058027670962, 0.8299999999999999600 ) ) ; +#25746 = ORIENTED_EDGE ( 'NONE', *, *, #37251, .T. ) ; +#25747 = FACE_BOUND ( 'NONE', #963, .T. ) ; +#25748 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.383333333333330195, 0.000000000000000000 ) ) ; +#25749 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9238200612200859752, 0.000000000000000000 ) ) ; +#25750 = ORIENTED_EDGE ( 'NONE', *, *, #31286, .F. ) ; +#25751 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.005000000000000006176, -0.2500000000000000000 ) ) ; +#25752 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25753 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83507 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47603, #78254, #7197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25754 = ADVANCED_FACE ( 'NONE', ( #31674 ), #85787, .T. ) ; +#25756 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999512, 0.8991599999999999593 ) ) ; +#25755 = SURFACE_STYLE_FILL_AREA ( #16532 ) ; +#25757 = CARTESIAN_POINT ( 'NONE', ( 1.596805013731110279, -1.020192282374009940, 0.8100000000000000533 ) ) ; +#25758 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25759 = CARTESIAN_POINT ( 'NONE', ( 0.2835602027787479940, -1.357109198394020000, 0.8100000000000000533 ) ) ; +#25760 = AXIS2_PLACEMENT_3D ( 'NONE', #788, #25325, #17109 ) ; +#25761 = CLOSED_SHELL ( 'NONE', ( #58708, #91103, #4608, #75564, #38568, #1580 ) ) ; +#25762 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#25763 = ORIENTED_EDGE ( 'NONE', *, *, #19467, .F. ) ; +#25764 = SURFACE_STYLE_USAGE ( .BOTH. , #26273 ) ; +#25765 = STYLED_ITEM ( 'NONE', ( #68903 ), #40447 ) ; +#25766 = SURFACE_STYLE_USAGE ( .BOTH. , #27276 ) ; +#25767 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.3000000000000013767, 0.1829999999999709359 ) ) ; +#25768 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58374 ) ) ; +#25769 = FACE_OUTER_BOUND ( 'NONE', #99927, .T. ) ; +#25770 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#25771 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#25772 = SURFACE_SIDE_STYLE ('',( #2290 ) ) ; +#25773 = FILL_AREA_STYLE ('',( #73728 ) ) ; +#25774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56769 ) ) ; +#25775 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25776 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25777 = SURFACE_STYLE_USAGE ( .BOTH. , #74237 ) ; +#25778 = ADVANCED_FACE ( 'NONE', ( #33197 ), #11622, .T. ) ; +#25779 = ADVANCED_FACE ( 'NONE', ( #26551 ), #87305, .F. ) ; +#25780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25781 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98507 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25991, #88754, #18270 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25782 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25783 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2959 ) ) ; +#25784 = LINE ( 'NONE', #1794, #99179 ) ; +#25785 = ORIENTED_EDGE ( 'NONE', *, *, #31939, .F. ) ; +#25786 = ORIENTED_EDGE ( 'NONE', *, *, #13729, .F. ) ; +#25787 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86600, 'distance_accuracy_value', 'NONE'); +#25788 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71088, 'distance_accuracy_value', 'NONE'); +#25789 = VECTOR ( 'NONE', #92050, 1000.000000000000000 ) ; +#25790 = LINE ( 'NONE', #42108, #87918 ) ; +#25791 = SURFACE_STYLE_FILL_AREA ( #49266 ) ; +#25792 = CARTESIAN_POINT ( 'NONE', ( 0.2761799387799149796, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#25793 = SURFACE_STYLE_FILL_AREA ( #3303 ) ; +#25794 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25795 = FACE_OUTER_BOUND ( 'NONE', #91946, .T. ) ; +#25797 = EDGE_LOOP ( 'NONE', ( #22486, #79267, #76785, #50206, #55272, #65497 ) ) ; +#25796 = STYLED_ITEM ( 'NONE', ( #1742 ), #75546 ) ; +#25798 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25799 = FILL_AREA_STYLE_COLOUR ( '', #40455 ) ; +#25800 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38275, 'distance_accuracy_value', 'NONE'); +#25801 = ADVANCED_FACE ( 'NONE', ( #81193 ), #9617, .T. ) ; +#25802 = SURFACE_STYLE_FILL_AREA ( #33461 ) ; +#25803 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #42479, .NOT_KNOWN. ) ; +#25804 = LINE ( 'NONE', #49793, #29172 ) ; +#25805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12663 ), #100704 ) ; +#25806 = ORIENTED_EDGE ( 'NONE', *, *, #84791, .F. ) ; +#25807 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, 0.000000000000000000 ) ) ; +#25808 = LINE ( 'NONE', #18611, #63085 ) ; +#25809 = VECTOR ( 'NONE', #79133, 1000.000000000000000 ) ; +#25810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25811 = ORIENTED_EDGE ( 'NONE', *, *, #97218, .F. ) ; +#25812 = AXIS2_PLACEMENT_3D ( 'NONE', #52691, #77666, #29202 ) ; +#25813 = SURFACE_STYLE_USAGE ( .BOTH. , #64101 ) ; +#25814 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20580, 'distance_accuracy_value', 'NONE'); +#25815 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27406 ) ) ; +#25817 = SURFACE_SIDE_STYLE ('',( #50332 ) ) ; +#25816 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69714 ), #51899 ) ; +#25818 = DIRECTION ( 'NONE', ( 0.7071067811865441310, 0.000000000000000000, 0.7071067811865510144 ) ) ; +#25819 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#25820 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68109 ) ) ; +#25821 = ORIENTED_EDGE ( 'NONE', *, *, #7362, .F. ) ; +#25822 = ADVANCED_FACE ( 'NONE', ( #5513 ), #82189, .T. ) ; +#25823 = PLANE ( 'NONE', #14587 ) ; +#25824 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#25825 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000001235, -0.1350000000000000089 ) ) ; +#25826 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25827 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25828 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25829 = VECTOR ( 'NONE', #76292, 1000.000000000000000 ) ; +#25830 = VECTOR ( 'NONE', #16556, 999.9999999999998863 ) ; +#25831 = ADVANCED_FACE ( 'NONE', ( #99393 ), #91808, .T. ) ; +#25832 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25833 = ORIENTED_EDGE ( 'NONE', *, *, #66361, .F. ) ; +#25834 = ORIENTED_EDGE ( 'NONE', *, *, #76528, .F. ) ; +#25835 = AXIS2_PLACEMENT_3D ( 'NONE', #70855, #83787, #52157 ) ; +#25836 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#25837 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25838 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25839 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25840 = CLOSED_SHELL ( 'NONE', ( #38501, #7913, #58429, #46946, #88946, #25707 ) ) ; +#25841 = FILL_AREA_STYLE ('',( #95725 ) ) ; +#25842 = ORIENTED_EDGE ( 'NONE', *, *, #27577, .T. ) ; +#25843 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25844 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8648700000000000276 ) ) ; +#25845 = AXIS2_PLACEMENT_3D ( 'NONE', #67937, #82308, #74636 ) ; +#25846 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25847 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#25848 = VERTEX_POINT ( 'NONE', #52534 ) ; +#25849 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69823 ) ) ; +#25851 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25850 = SURFACE_SIDE_STYLE ('',( #24856 ) ) ; +#25852 = ORIENTED_EDGE ( 'NONE', *, *, #44663, .F. ) ; +#25853 = VERTEX_POINT ( 'NONE', #97456 ) ; +#25855 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25854 = FILL_AREA_STYLE ('',( #26861 ) ) ; +#25856 = EDGE_CURVE ( 'NONE', #72784, #80604, #51563, .T. ) ; +#25857 = PRESENTATION_STYLE_ASSIGNMENT (( #26358 ) ) ; +#25858 = ORIENTED_EDGE ( 'NONE', *, *, #63824, .F. ) ; +#25859 = AXIS2_PLACEMENT_3D ( 'NONE', #94440, #39840, #30626 ) ; +#25860 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25861 = ORIENTED_EDGE ( 'NONE', *, *, #37539, .T. ) ; +#25862 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8100000000000000533 ) ) ; +#25863 = VERTEX_POINT ( 'NONE', #83680 ) ; +#25864 = FILL_AREA_STYLE_COLOUR ( '', #56843 ) ; +#25865 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25866 = CARTESIAN_POINT ( 'NONE', ( -1.094250269889780025, -1.238505293396390039, 0.8299999999999999600 ) ) ; +#25867 = ADVANCED_FACE ( 'NONE', ( #13646 ), #44831, .T. ) ; +#25868 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33738, 'distance_accuracy_value', 'NONE'); +#25870 = SURFACE_STYLE_FILL_AREA ( #56530 ) ; +#25871 = EDGE_CURVE ( 'NONE', #75075, #9766, #47886, .T. ) ; +#25872 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#25873 = LINE ( 'NONE', #89651, #50814 ) ; +#25874 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#25875 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#25876 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2035 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28743, #13346, #67529 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25877 = VERTEX_POINT ( 'NONE', #916 ) ; +#25878 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -7.594371560187039807E-15, 0.000000000000000000 ) ) ; +#25879 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25880 = EDGE_CURVE ( 'NONE', #34880, #44500, #37716, .T. ) ; +#25881 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#25882 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.8999999999999993561, -0.02000000000000000042 ) ) ; +#25883 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17671 ) ) ; +#25884 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25885 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69858 ), #34051 ) ; +#25886 = AXIS2_PLACEMENT_3D ( 'NONE', #6593, #68431, #53640 ) ; +#25887 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.000000000000000000 ) ) ; +#25888 = EDGE_CURVE ( 'NONE', #90644, #2363, #100856, .T. ) ; +#25889 = FILL_AREA_STYLE_COLOUR ( '', #66274 ) ; +#25890 = PRESENTATION_STYLE_ASSIGNMENT (( #19192 ) ) ; +#25891 = VERTEX_POINT ( 'NONE', #31053 ) ; +#25892 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25893 = FILL_AREA_STYLE_COLOUR ( '', #5320 ) ; +#25894 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25895 = CYLINDRICAL_SURFACE ( 'NONE', #7005, 0.1200000000000000927 ) ; +#25896 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25897 = CARTESIAN_POINT ( 'NONE', ( 0.4674268961122319821, -1.076021161212330046, 0.8300000000000015143 ) ) ; +#25898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21279, 'distance_accuracy_value', 'NONE'); +#25899 = DIRECTION ( 'NONE', ( 0.7071090539100497452, 0.7071045084557405769, 0.000000000000000000 ) ) ; +#25900 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#25901 = CARTESIAN_POINT ( 'NONE', ( 1.166666666666660079, -3.500000000000000000, 0.000000000000000000 ) ) ; +#25902 = SURFACE_STYLE_FILL_AREA ( #40210 ) ; +#25904 = EDGE_CURVE ( 'NONE', #45824, #38401, #46339, .T. ) ; +#25903 = PLANE ( 'NONE', #33687 ) ; +#25905 = ADVANCED_FACE ( 'NONE', ( #62718 ), #15171, .F. ) ; +#25906 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#25907 = AXIS2_PLACEMENT_3D ( 'NONE', #53392, #69161, #45189 ) ; +#25908 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#25909 = VECTOR ( 'NONE', #94672, 1000.000000000000000 ) ; +#25910 = ADVANCED_FACE ( 'NONE', ( #38214 ), #89820, .T. ) ; +#25911 = EDGE_CURVE ( 'NONE', #99643, #4210, #18730, .T. ) ; +#25912 = STYLED_ITEM ( 'NONE', ( #69170 ), #42117 ) ; +#25913 = PLANE ( 'NONE', #53598 ) ; +#25914 = SURFACE_STYLE_FILL_AREA ( #70445 ) ; +#25915 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #73668, 'design' ) ; +#25916 = PRESENTATION_STYLE_ASSIGNMENT (( #17704 ) ) ; +#25917 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#25918 = EDGE_LOOP ( 'NONE', ( #23681, #53961, #40367, #9732 ) ) ; +#25919 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#25920 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#25921 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82286, 'distance_accuracy_value', 'NONE'); +#25922 = EDGE_CURVE ( 'NONE', #21114, #31104, #96681, .T. ) ; +#25923 = PRESENTATION_STYLE_ASSIGNMENT (( #80545 ) ) ; +#25924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39261, 'distance_accuracy_value', 'NONE'); +#25926 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25925 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959499, 0.000000000000000000 ) ) ; +#25927 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#25928 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8199999999999999512 ) ) ; +#25929 = ADVANCED_FACE ( 'NONE', ( #34603 ), #87194, .T. ) ; +#25930 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60126 ) ) ; +#25931 = FILL_AREA_STYLE ('',( #81060 ) ) ; +#25932 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#25933 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31785 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29359, #12445, #81996 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#25934 = ORIENTED_EDGE ( 'NONE', *, *, #37764, .T. ) ; +#25935 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25936 = LINE ( 'NONE', #35606, #71844 ) ; +#25937 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25938 = CYLINDRICAL_SURFACE ( 'NONE', #21119, 0.009999999999999998473 ) ; +#25939 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61568, 'distance_accuracy_value', 'NONE'); +#25940 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4850000000000001532, 0.2458578643762690530 ) ) ; +#25941 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1218, 'distance_accuracy_value', 'NONE'); +#25942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25943 = ORIENTED_EDGE ( 'NONE', *, *, #49632, .T. ) ; +#25944 = VERTEX_POINT ( 'NONE', #18212 ) ; +#25945 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25946 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8648700000000000276 ) ) ; +#25947 = ORIENTED_EDGE ( 'NONE', *, *, #97389, .F. ) ; +#25948 = DIRECTION ( 'NONE', ( -0.7071045084557425753, 0.7071090539100477468, 0.000000000000000000 ) ) ; +#25949 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83067 ) ) ; +#25950 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.149999999999999911, 0.000000000000000000 ) ) ; +#25951 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#25952 = DIRECTION ( 'NONE', ( 0.3387340427540269649, -0.000000000000000000, 0.9408821649279537347 ) ) ; +#25953 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69920 ) ) ; +#25954 = VECTOR ( 'NONE', #52020, 1000.000000000000000 ) ; +#25955 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #37146 ) ; +#25956 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#25958 = ORIENTED_EDGE ( 'NONE', *, *, #41235, .F. ) ; +#25957 = ORIENTED_EDGE ( 'NONE', *, *, #73008, .F. ) ; +#25959 = ADVANCED_FACE ( 'NONE', ( #49401 ), #72883, .T. ) ; +#25960 = VERTEX_POINT ( 'NONE', #7239 ) ; +#25961 = VECTOR ( 'NONE', #57373, 1000.000000000000000 ) ; +#25962 = EDGE_LOOP ( 'NONE', ( #61764, #45948, #77161, #40258 ) ) ; +#25963 = SURFACE_SIDE_STYLE ('',( #73421 ) ) ; +#25964 = VECTOR ( 'NONE', #33964, 1000.000000000000000 ) ; +#25966 = CARTESIAN_POINT ( 'NONE', ( 1.414009484217380042, -1.031612284007709990, 0.8100000000000000533 ) ) ; +#25965 = CARTESIAN_POINT ( 'NONE', ( 0.5450788742336990511, -1.052784384528720141, 0.8299999999999999600 ) ) ; +#25967 = ORIENTED_EDGE ( 'NONE', *, *, #70043, .F. ) ; +#25968 = EDGE_CURVE ( 'NONE', #77419, #54388, #4422, .T. ) ; +#25969 = VECTOR ( 'NONE', #77994, 1000.000000000000000 ) ; +#25970 = VECTOR ( 'NONE', #15557, 999.9999999999998863 ) ; +#25971 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#25972 = ORIENTED_EDGE ( 'NONE', *, *, #9877, .F. ) ; +#25973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#25974 = ORIENTED_EDGE ( 'NONE', *, *, #52633, .F. ) ; +#25975 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25976 = EDGE_LOOP ( 'NONE', ( #69083, #26099, #30488, #68478 ) ) ; +#25977 = EDGE_LOOP ( 'NONE', ( #96442, #9647, #24468, #48701 ) ) ; +#25978 = FACE_OUTER_BOUND ( 'NONE', #28369, .T. ) ; +#25979 = VECTOR ( 'NONE', #56645, 1000.000000000000000 ) ; +#25980 = FILL_AREA_STYLE_COLOUR ( '', #46140 ) ; +#25981 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#25982 = EDGE_CURVE ( 'NONE', #4926, #58891, #28428, .T. ) ; +#25983 = STYLED_ITEM ( 'NONE', ( #61541 ), #1136 ) ; +#25985 = ORIENTED_EDGE ( 'NONE', *, *, #29369, .F. ) ; +#25984 = SURFACE_SIDE_STYLE ('',( #64757 ) ) ; +#25986 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25987 = VERTEX_POINT ( 'NONE', #61474 ) ; +#25988 = SURFACE_STYLE_USAGE ( .BOTH. , #35158 ) ; +#25989 = VERTEX_POINT ( 'NONE', #12519 ) ; +#25991 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#25990 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#25992 = ORIENTED_EDGE ( 'NONE', *, *, #69, .F. ) ; +#25993 = ORIENTED_EDGE ( 'NONE', *, *, #16078, .T. ) ; +#25995 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#25994 = PRESENTATION_STYLE_ASSIGNMENT (( #95885 ) ) ; +#25996 = EDGE_CURVE ( 'NONE', #13041, #93078, #43727, .T. ) ; +#25997 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#25998 = SURFACE_STYLE_USAGE ( .BOTH. , #17782 ) ; +#25999 = CARTESIAN_POINT ( 'NONE', ( -1.292790076653027365, -1.080732611435678336, 0.8099999999999284439 ) ) ; +#26000 = FILL_AREA_STYLE ('',( #10545 ) ) ; +#26001 = PRESENTATION_STYLE_ASSIGNMENT (( #79106 ) ) ; +#26002 = VERTEX_POINT ( 'NONE', #100616 ) ; +#26003 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26004 = ORIENTED_EDGE ( 'NONE', *, *, #92105, .F. ) ; +#26005 = EDGE_CURVE ( 'NONE', #37874, #79602, #65069, .T. ) ; +#26006 = SURFACE_STYLE_FILL_AREA ( #33667 ) ; +#26007 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12915 ), #97710 ) ; +#26008 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#26009 = SURFACE_STYLE_FILL_AREA ( #24517 ) ; +#26010 = FILL_AREA_STYLE ('',( #56148 ) ) ; +#26011 = ADVANCED_FACE ( 'NONE', ( #61974 ), #51926, .T. ) ; +#26012 = CARTESIAN_POINT ( 'NONE', ( 1.662784294148539344, -1.164927051866627261, 0.8099999999999999423 ) ) ; +#26013 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26014 = FILL_AREA_STYLE_COLOUR ( '', #39679 ) ; +#26015 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.000000000000000000 ) ) ; +#26016 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#26017 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#26018 = LINE ( 'NONE', #39809, #36773 ) ; +#26019 = EDGE_CURVE ( 'NONE', #91118, #41436, #92555, .T. ) ; +#26020 = VECTOR ( 'NONE', #82472, 999.9999999999998863 ) ; +#26021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26022 = LINE ( 'NONE', #33683, #72990 ) ; +#26023 = FILL_AREA_STYLE_COLOUR ( '', #44079 ) ; +#26024 = LINE ( 'NONE', #28036, #12809 ) ; +#26025 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.1499999999999999667, -0.01999999999999999695 ) ) ; +#26026 = VECTOR ( 'NONE', #38392, 1000.000000000000000 ) ; +#26027 = ADVANCED_FACE ( 'NONE', ( #14931 ), #42741, .T. ) ; +#26028 = EDGE_CURVE ( 'NONE', #23968, #62161, #8247, .T. ) ; +#26029 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78197 ), #52119 ) ; +#26030 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26031 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11623, 'distance_accuracy_value', 'NONE'); +#26032 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #40221, #32048, #16674, #95295 ), + ( #895, #8975, #47871, #63215 ), + ( #24411, #24923, #32563, #63715 ), + ( #70327, #85654, #48404, #62207 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243646044, 0.6476030138606874154, 0.6476030138606874154, 0.8047378541243646044), + ( 0.8047378541243646044, 0.6476030138606874154, 0.6476030138606874154, 0.8047378541243646044), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#26033 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26034 = ORIENTED_EDGE ( 'NONE', *, *, #398, .T. ) ; +#26035 = CARTESIAN_POINT ( 'NONE', ( 1.601121020982049892, -0.9216047924506349798, 0.8299999999999999600 ) ) ; +#26036 = CIRCLE ( 'NONE', #27647, 0.009999999999999998473 ) ; +#26037 = ORIENTED_EDGE ( 'NONE', *, *, #62160, .T. ) ; +#26038 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26039 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26040 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84668 ), #7918 ) ; +#26041 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26042 = CARTESIAN_POINT ( 'NONE', ( 1.750951194234720010, -0.9053603395923379704, 0.8299999999999999600 ) ) ; +#26043 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26044 = EDGE_CURVE ( 'NONE', #59345, #71441, #16449, .T. ) ; +#26045 = EDGE_CURVE ( 'NONE', #47020, #12156, #155, .T. ) ; +#26046 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26047 = AXIS2_PLACEMENT_3D ( 'NONE', #22976, #15251, #38780 ) ; +#26048 = EDGE_LOOP ( 'NONE', ( #66654, #19279, #75179, #35148 ) ) ; +#26049 = ORIENTED_EDGE ( 'NONE', *, *, #63571, .T. ) ; +#26050 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94439 ), #87979 ) ; +#26051 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26053 = VECTOR ( 'NONE', #32545, 1000.000000000000000 ) ; +#26052 = SURFACE_STYLE_FILL_AREA ( #88320 ) ; +#26054 = SURFACE_STYLE_FILL_AREA ( #72480 ) ; +#26055 = CARTESIAN_POINT ( 'NONE', ( 4.409146500500175314, 7.671290500500174581, 0.8991599999999999593 ) ) ; +#26056 = SURFACE_SIDE_STYLE ('',( #88823 ) ) ; +#26057 = LINE ( 'NONE', #17848, #68068 ) ; +#26058 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26059 = LINE ( 'NONE', #24568, #38094 ) ; +#26060 = ORIENTED_EDGE ( 'NONE', *, *, #22779, .T. ) ; +#26061 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26062 = FILL_AREA_STYLE ('',( #9125 ) ) ; +#26063 = ORIENTED_EDGE ( 'NONE', *, *, #27048, .F. ) ; +#26064 = ORIENTED_EDGE ( 'NONE', *, *, #81125, .T. ) ; +#26066 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26065 = AXIS2_PLACEMENT_3D ( 'NONE', #22471, #76094, #69921 ) ; +#26067 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#26068 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20881 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #133, #100591, #1676 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26069 = CARTESIAN_POINT ( 'NONE', ( -1.102215942591399989, -0.9616422087329199453, 0.8100000000000000533 ) ) ; +#26070 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26071 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26072 = FILL_AREA_STYLE_COLOUR ( '', #7237 ) ; +#26074 = VERTEX_POINT ( 'NONE', #31812 ) ; +#26073 = ORIENTED_EDGE ( 'NONE', *, *, #72828, .T. ) ; +#26075 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.100000000000000089, 0.1829999999999619709 ) ) ; +#26076 = VECTOR ( 'NONE', #31941, 1000.000000000000000 ) ; +#26077 = EDGE_LOOP ( 'NONE', ( #26841, #44714, #51486, #18037 ) ) ; +#26078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26080 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#26079 = FILL_AREA_STYLE ('',( #79703 ) ) ; +#26081 = VERTEX_POINT ( 'NONE', #86956 ) ; +#26082 = EDGE_CURVE ( 'NONE', #13289, #15215, #72139, .T. ) ; +#26083 = ORIENTED_EDGE ( 'NONE', *, *, #90568, .F. ) ; +#26084 = LINE ( 'NONE', #64366, #74106 ) ; +#26085 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26086 = VECTOR ( 'NONE', #43476, 1000.000000000000114 ) ; +#26088 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#26087 = SURFACE_STYLE_FILL_AREA ( #2096 ) ; +#26089 = FILL_AREA_STYLE_COLOUR ( '', #9890 ) ; +#26090 = EDGE_LOOP ( 'NONE', ( #96189, #75221, #33316, #56320 ) ) ; +#26091 = VERTEX_POINT ( 'NONE', #33339 ) ; +#26092 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#26093 = ORIENTED_EDGE ( 'NONE', *, *, #34427, .F. ) ; +#26094 = PLANE ( 'NONE', #18772 ) ; +#26095 = FACE_OUTER_BOUND ( 'NONE', #79112, .T. ) ; +#26096 = STYLED_ITEM ( 'NONE', ( #36149 ), #86053 ) ; +#26097 = VECTOR ( 'NONE', #3721, 1000.000000000000114 ) ; +#26099 = ORIENTED_EDGE ( 'NONE', *, *, #54022, .F. ) ; +#26098 = SURFACE_SIDE_STYLE ('',( #95990 ) ) ; +#26100 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43999 ) ) ; +#26101 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26102 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.600000000000000089, 0.000000000000000000 ) ) ; +#26103 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66930 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29231, #60411, #36401 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26104 = PRESENTATION_STYLE_ASSIGNMENT (( #87861 ) ) ; +#26105 = ORIENTED_EDGE ( 'NONE', *, *, #27829, .T. ) ; +#26106 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#26107 = SURFACE_STYLE_USAGE ( .BOTH. , #87358 ) ; +#26108 = ORIENTED_EDGE ( 'NONE', *, *, #79859, .F. ) ; +#26109 = PRESENTATION_STYLE_ASSIGNMENT (( #6656 ) ) ; +#26110 = PLANE ( 'NONE', #66044 ) ; +#26112 = PRESENTATION_STYLE_ASSIGNMENT (( #57260 ) ) ; +#26111 = AXIS2_PLACEMENT_3D ( 'NONE', #50640, #64431, #81779 ) ; +#26113 = CARTESIAN_POINT ( 'NONE', ( -1.362892881570719972, -1.113830263093820161, 0.8300000000000000711 ) ) ; +#26114 = ADVANCED_FACE ( 'NONE', ( #9755 ), #23659, .T. ) ; +#26115 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#26116 = SURFACE_SIDE_STYLE ('',( #95500 ) ) ; +#26117 = LINE ( 'NONE', #25128, #40629 ) ; +#26119 = LINE ( 'NONE', #57267, #31962 ) ; +#26118 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#26120 = CARTESIAN_POINT ( 'NONE', ( -1.476179938779914602, -3.099999999999990319, -0.02000000000000000042 ) ) ; +#26121 = VERTEX_POINT ( 'NONE', #71640 ) ; +#26122 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26123 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73347 ), #29307 ) ; +#26124 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 1.699999999999999956, 1.747825839084982648E-76 ) ) ; +#26125 = VERTEX_POINT ( 'NONE', #9250 ) ; +#26126 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#26127 = VECTOR ( 'NONE', #7891, 1000.000000000000000 ) ; +#26128 = PLANE ( 'NONE', #56222 ) ; +#26129 = PRESENTATION_STYLE_ASSIGNMENT (( #40945 ) ) ; +#26130 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8648700000000000276 ) ) ; +#26131 = CARTESIAN_POINT ( 'NONE', ( 1.325735931288071434, 0.6599999999999998090, -1.100000000000000089 ) ) ; +#26132 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26133 = ADVANCED_FACE ( 'NONE', ( #1697 ), #85928, .T. ) ; +#26134 = LINE ( 'NONE', #57280, #43360 ) ; +#26136 = FACE_OUTER_BOUND ( 'NONE', #92680, .T. ) ; +#26135 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16302 ), #89729 ) ; +#26137 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71747 ), #92890 ) ; +#26138 = FACE_OUTER_BOUND ( 'NONE', #78201, .T. ) ; +#26139 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11300 ) ) ; +#26141 = VERTEX_POINT ( 'NONE', #26692 ) ; +#26142 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#26143 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#26144 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26145 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#26146 = ADVANCED_FACE ( 'NONE', ( #65460 ), #74148, .F. ) ; +#26147 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46251, 'distance_accuracy_value', 'NONE'); +#26148 = VERTEX_POINT ( 'NONE', #74654 ) ; +#26149 = SURFACE_STYLE_USAGE ( .BOTH. , #34324 ) ; +#26150 = PRESENTATION_STYLE_ASSIGNMENT (( #17931 ) ) ; +#26151 = CARTESIAN_POINT ( 'NONE', ( -1.153771935001989934, -0.9546485130184679813, 0.8299999999999999600 ) ) ; +#26152 = LINE ( 'NONE', #3153, #54324 ) ; +#26153 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26154 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26155 = SURFACE_STYLE_USAGE ( .BOTH. , #89427 ) ; +#26156 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3329 ), #91360 ) ; +#26157 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#26158 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55658, #33679, #64298, #32157 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#26159 = SURFACE_SIDE_STYLE ('',( #64941 ) ) ; +#26160 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #90256, #61656 ), + ( #91740, #5938 ), + ( #14110, #23340 ), + ( #14612, #6435 ), + ( #55000, #30981 ), + ( #53968, #75941 ), + ( #99337, #54492 ), + ( #77435, #38645 ), + ( #37161, #37653 ), + ( #85602, #68260 ), + ( #70278, #21814 ), + ( #76952, #85100 ), + ( #62162, #15109 ), + ( #84104, #99802 ), + ( #45263, #68755 ), + ( #92250, #29957 ), + ( #61151, #46267 ), + ( #23849, #69229 ), + ( #22312, #46786 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07149115047970650005, 0.1387482511670830032, 0.2024524341567409957, 0.2636912508091490137, 0.3230850051389609900, 0.3813511167042549777, 0.4391309649659340120, 0.4974277397290590153, 0.5562304511353219905, 0.6156242054651339668, 0.6763078083294490339, 0.7386509055408330138, 0.8025070736687720530, 0.8670020345552610364, 0.9328234660649350474, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#26161 = AXIS2_PLACEMENT_3D ( 'NONE', #8911, #78940, #95229 ) ; +#26162 = ADVANCED_FACE ( 'NONE', ( #73642 ), #49674, .T. ) ; +#26163 = STYLED_ITEM ( 'NONE', ( #42338 ), #95049 ) ; +#26164 = FACE_OUTER_BOUND ( 'NONE', #1425, .T. ) ; +#26165 = SURFACE_STYLE_FILL_AREA ( #49141 ) ; +#26166 = EDGE_LOOP ( 'NONE', ( #59530, #42039, #100404, #100150 ) ) ; +#26167 = ORIENTED_EDGE ( 'NONE', *, *, #10056, .F. ) ; +#26168 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49588, 'distance_accuracy_value', 'NONE'); +#26169 = PRESENTATION_STYLE_ASSIGNMENT (( #73622 ) ) ; +#26170 = PLANE ( 'NONE', #18579 ) ; +#26171 = VECTOR ( 'NONE', #78779, 1000.000000000000000 ) ; +#26172 = LINE ( 'NONE', #82302, #18393 ) ; +#26173 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9715 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32138, #63795, #39789 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26174 = CARTESIAN_POINT ( 'NONE', ( 0.4895572725034796902, -1.211251862793616851, 0.8100000000000003864 ) ) ; +#26175 = FILL_AREA_STYLE_COLOUR ( '', #13393 ) ; +#26176 = PLANE ( 'NONE', #41875 ) ; +#26177 = PLANE ( 'NONE', #88524 ) ; +#26178 = ORIENTED_EDGE ( 'NONE', *, *, #41089, .T. ) ; +#26179 = SURFACE_STYLE_FILL_AREA ( #9745 ) ; +#26180 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.000000000000000000 ) ) ; +#26181 = VERTEX_POINT ( 'NONE', #52185 ) ; +#26182 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40832 ) ) ; +#26183 = STYLED_ITEM ( 'NONE', ( #99718 ), #65502 ) ; +#26184 = ORIENTED_EDGE ( 'NONE', *, *, #4644, .T. ) ; +#26185 = PLANE ( 'NONE', #89237 ) ; +#26186 = FACE_OUTER_BOUND ( 'NONE', #36686, .T. ) ; +#26187 = SURFACE_STYLE_FILL_AREA ( #96082 ) ; +#26188 = EDGE_CURVE ( 'NONE', #4035, #72784, #43994, .T. ) ; +#26189 = COLOUR_RGB ( '',0.6666666666666666297, 0.6666666666666666297, 0.6666666666666666297 ) ; +#26190 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26191 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.004999999999999987094, -0.1500000000000000222 ) ) ; +#26192 = FILL_AREA_STYLE_COLOUR ( '', #69148 ) ; +#26193 = AXIS2_PLACEMENT_3D ( 'NONE', #38551, #44185, #29866 ) ; +#26194 = VERTEX_POINT ( 'NONE', #75638 ) ; +#26195 = AXIS2_PLACEMENT_3D ( 'NONE', #52959, #84569, #60622 ) ; +#26196 = SURFACE_STYLE_USAGE ( .BOTH. , #94586 ) ; +#26197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16290 ) ) ; +#26198 = EDGE_LOOP ( 'NONE', ( #158, #71401, #86817, #71113 ) ) ; +#26199 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26200 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60407, 'distance_accuracy_value', 'NONE'); +#26201 = EDGE_CURVE ( 'NONE', #48692, #17228, #51685, .T. ) ; +#26202 = ORIENTED_EDGE ( 'NONE', *, *, #84917, .F. ) ; +#26203 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26204 = FACE_OUTER_BOUND ( 'NONE', #8353, .T. ) ; +#26205 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#26206 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558440262, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#26207 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26208 = STYLED_ITEM ( 'NONE', ( #54402 ), #51504 ) ; +#26209 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26211 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26210 = FILL_AREA_STYLE_COLOUR ( '', #19921 ) ; +#26212 = ORIENTED_EDGE ( 'NONE', *, *, #71404, .T. ) ; +#26214 = ORIENTED_EDGE ( 'NONE', *, *, #26429, .F. ) ; +#26213 = ORIENTED_EDGE ( 'NONE', *, *, #39027, .T. ) ; +#26215 = LINE ( 'NONE', #89491, #22143 ) ; +#26216 = ORIENTED_EDGE ( 'NONE', *, *, #39717, .F. ) ; +#26217 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.2000000000000000111, -12.44500000000000028 ) ) ; +#26218 = VECTOR ( 'NONE', #19381, 1000.000000000000000 ) ; +#26219 = EDGE_LOOP ( 'NONE', ( #61993, #29491, #60748, #47383 ) ) ; +#26220 = ORIENTED_EDGE ( 'NONE', *, *, #13922, .F. ) ; +#26222 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#26221 = PRESENTATION_STYLE_ASSIGNMENT (( #56381 ) ) ; +#26223 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26224 = EDGE_LOOP ( 'NONE', ( #48673, #74376, #4311, #28331 ) ) ; +#26225 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26226 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26227 = PRESENTATION_STYLE_ASSIGNMENT (( #95108 ) ) ; +#26228 = VERTEX_POINT ( 'NONE', #20508 ) ; +#26229 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26230 = FACE_OUTER_BOUND ( 'NONE', #98450, .T. ) ; +#26231 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11461 ) ) ; +#26232 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70206 ), #14778 ) ; +#26233 = SURFACE_STYLE_USAGE ( .BOTH. , #41546 ) ; +#26234 = EDGE_CURVE ( 'NONE', #87124, #37213, #13794, .T. ) ; +#26235 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26236 = STYLED_ITEM ( 'NONE', ( #73813 ), #93600 ) ; +#26237 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26238 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26239 = STYLED_ITEM ( 'NONE', ( #2873 ), #57867 ) ; +#26240 = PRESENTATION_STYLE_ASSIGNMENT (( #33909 ) ) ; +#26241 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26243 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#26244 = PRESENTATION_STYLE_ASSIGNMENT (( #10303 ) ) ; +#26245 = EDGE_CURVE ( 'NONE', #28814, #79785, #99524, .T. ) ; +#26246 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8648700000000000276 ) ) ; +#26247 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42497 ), #83311 ) ; +#26248 = EDGE_CURVE ( 'NONE', #66856, #67521, #53175, .T. ) ; +#26249 = FILL_AREA_STYLE ('',( #96143 ) ) ; +#26250 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18030 ), #73546 ) ; +#26251 = CARTESIAN_POINT ( 'NONE', ( 1.177393120509059976, -0.8847374564574109757, 0.8299999999999999600 ) ) ; +#26252 = ORIENTED_EDGE ( 'NONE', *, *, #26044, .F. ) ; +#26253 = PLANE ( 'NONE', #69143 ) ; +#26254 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49927, #81076, #35118, #64226 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#26255 = SURFACE_STYLE_USAGE ( .BOTH. , #57400 ) ; +#26256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26257 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000444, 0.000000000000000000 ) ) ; +#26258 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26259 = ORIENTED_EDGE ( 'NONE', *, *, #97454, .T. ) ; +#26260 = FACE_OUTER_BOUND ( 'NONE', #4462, .T. ) ; +#26261 = STYLED_ITEM ( 'NONE', ( #88027 ), #64817 ) ; +#26262 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.05000000000000000278, 0.08229670385730990245 ) ) ; +#26263 = AXIS2_PLACEMENT_3D ( 'NONE', #72100, #8201, #61932 ) ; +#26264 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000089, 2.523820061220085176, 0.000000000000000000 ) ) ; +#26265 = FILL_AREA_STYLE ('',( #10318 ) ) ; +#26266 = CIRCLE ( 'NONE', #39203, 0.3000000000000000444 ) ; +#26267 = CARTESIAN_POINT ( 'NONE', ( -0.2389181574176280354, -1.341601374162270099, 0.8299999999999999600 ) ) ; +#26268 = SURFACE_STYLE_USAGE ( .BOTH. , #96161 ) ; +#26269 = EDGE_CURVE ( 'NONE', #18739, #4168, #57893, .T. ) ; +#26270 = SURFACE_SIDE_STYLE ('',( #42583 ) ) ; +#26271 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26272 = ORIENTED_EDGE ( 'NONE', *, *, #50848, .T. ) ; +#26273 = SURFACE_SIDE_STYLE ('',( #95660 ) ) ; +#26274 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#26275 = SURFACE_STYLE_FILL_AREA ( #49763 ) ; +#26276 = FACE_OUTER_BOUND ( 'NONE', #44141, .T. ) ; +#26277 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26278 = FILL_AREA_STYLE ('',( #81906 ) ) ; +#26279 = AXIS2_PLACEMENT_3D ( 'NONE', #87546, #8330, #77863 ) ; +#26280 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26281 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26282 = FACE_OUTER_BOUND ( 'NONE', #56072, .T. ) ; +#26283 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000089, 0.000000000000000000 ) ) ; +#26285 = VECTOR ( 'NONE', #88234, 1000.000000000000000 ) ; +#26284 = FILL_AREA_STYLE ('',( #96181 ) ) ; +#26286 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71899 ), #52366 ) ; +#26287 = EDGE_CURVE ( 'NONE', #81759, #74469, #21510, .T. ) ; +#26288 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26289 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#26290 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#26291 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26292 = ORIENTED_EDGE ( 'NONE', *, *, #64392, .T. ) ; +#26293 = CYLINDRICAL_SURFACE ( 'NONE', #83983, 0.05000000000000012768 ) ; +#26294 = ORIENTED_EDGE ( 'NONE', *, *, #32661, .T. ) ; +#26295 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97923 ), #84920 ) ; +#26296 = SURFACE_STYLE_FILL_AREA ( #73743 ) ; +#26297 = CARTESIAN_POINT ( 'NONE', ( 0.1500588324485339908, -1.474796765042009961, 0.8299999999999999600 ) ) ; +#26298 = SURFACE_STYLE_FILL_AREA ( #41115 ) ; +#26299 = SURFACE_STYLE_USAGE ( .BOTH. , #65574 ) ; +#26300 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#26301 = ORIENTED_EDGE ( 'NONE', *, *, #16985, .T. ) ; +#26302 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#26303 = DIRECTION ( 'NONE', ( 6.165170508236590408E-78, 1.306104834246980087E-31, 1.000000000000000000 ) ) ; +#26304 = VECTOR ( 'NONE', #26693, 1000.000000000000000 ) ; +#26305 = LINE ( 'NONE', #87566, #87903 ) ; +#26306 = ORIENTED_EDGE ( 'NONE', *, *, #61871, .T. ) ; +#26307 = SURFACE_STYLE_FILL_AREA ( #26814 ) ; +#26308 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32851 ) ) ; +#26309 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26310 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44196 ), #75202 ) ; +#26311 = EDGE_CURVE ( 'NONE', #5639, #25960, #29667, .T. ) ; +#26312 = PLANE ( 'NONE', #22851 ) ; +#26313 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999959338, -0.1400000000000000411 ) ) ; +#26314 = VERTEX_POINT ( 'NONE', #21021 ) ; +#26315 = FILL_AREA_STYLE_COLOUR ( '', #64522 ) ; +#26316 = VECTOR ( 'NONE', #89882, 1000.000000000000000 ) ; +#26317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55994, 'distance_accuracy_value', 'NONE'); +#26318 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26319 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26320 = ADVANCED_FACE ( 'NONE', ( #5150 ), #14304, .T. ) ; +#26321 = ORIENTED_EDGE ( 'NONE', *, *, #79423, .F. ) ; +#26322 = CYLINDRICAL_SURFACE ( 'NONE', #87219, 0.05000000000000002359 ) ; +#26323 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26324 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8099999999999112354 ) ) ; +#26326 = STYLED_ITEM ( 'NONE', ( #4899 ), #20942 ) ; +#26325 = CARTESIAN_POINT ( 'NONE', ( -1.303671509438067311, -1.178641562787474451, 0.8099999999998565015 ) ) ; +#26327 = AXIS2_PLACEMENT_3D ( 'NONE', #88931, #28158, #59334 ) ; +#26328 = EDGE_CURVE ( 'NONE', #18845, #50863, #22011, .T. ) ; +#26329 = FACE_OUTER_BOUND ( 'NONE', #76715, .T. ) ; +#26330 = LINE ( 'NONE', #42147, #74274 ) ; +#26331 = VECTOR ( 'NONE', #88406, 1000.000000000000000 ) ; +#26332 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29517 ), #13187 ) ; +#26333 = EDGE_CURVE ( 'NONE', #94767, #45093, #6624, .T. ) ; +#26334 = STYLED_ITEM ( 'NONE', ( #57244 ), #69538 ) ; +#26335 = ORIENTED_EDGE ( 'NONE', *, *, #1868, .F. ) ; +#26337 = ORIENTED_EDGE ( 'NONE', *, *, #81891, .T. ) ; +#26336 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.7000000000000022871, 0.8299999999999999600 ) ) ; +#26338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14582, 'distance_accuracy_value', 'NONE'); +#26340 = FACE_OUTER_BOUND ( 'NONE', #57672, .T. ) ; +#26339 = PRESENTATION_STYLE_ASSIGNMENT (( #17129 ) ) ; +#26341 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 1.757708562033497989E-17, 0.2499999999999998890 ) ) ; +#26342 = LINE ( 'NONE', #9898, #86666 ) ; +#26343 = ORIENTED_EDGE ( 'NONE', *, *, #56070, .F. ) ; +#26344 = LINE ( 'NONE', #58522, #52284 ) ; +#26345 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26346 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4849999999999999867, -0.2500000000000000000 ) ) ; +#26347 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57334 ) ) ; +#26348 = VERTEX_POINT ( 'NONE', #92438 ) ; +#26350 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26349 = PLANE ( 'NONE', #79800 ) ; +#26351 = ORIENTED_EDGE ( 'NONE', *, *, #25105, .F. ) ; +#26353 = ADVANCED_FACE ( 'NONE', ( #22512 ), #77139, .T. ) ; +#26352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11594 ) ) ; +#26354 = ORIENTED_EDGE ( 'NONE', *, *, #54022, .T. ) ; +#26355 = EDGE_CURVE ( 'NONE', #25863, #10244, #1051, .T. ) ; +#26357 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26356 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#26358 = SURFACE_STYLE_USAGE ( .BOTH. , #65140 ) ; +#26359 = ORIENTED_EDGE ( 'NONE', *, *, #32776, .F. ) ; +#26360 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26361 = VERTEX_POINT ( 'NONE', #61848 ) ; +#26362 = CARTESIAN_POINT ( 'NONE', ( 1.278904811106269968, -1.437631519369750199, 0.8100000000000000533 ) ) ; +#26363 = FACE_OUTER_BOUND ( 'NONE', #28199, .T. ) ; +#26364 = EDGE_LOOP ( 'NONE', ( #75670, #37017, #37277, #32484, #92200, #94821 ) ) ; +#26365 = SURFACE_STYLE_USAGE ( .BOTH. , #18660 ) ; +#26366 = CARTESIAN_POINT ( 'NONE', ( -1.244474960515300044, -1.202560495203230051, 0.8100000000000000533 ) ) ; +#26368 = EDGE_CURVE ( 'NONE', #53179, #33480, #54172, .T. ) ; +#26367 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67341, #98908, #59750, #57730, #88833, #78033, #46350, #37240, #100864, #21385, #46863, #6007, #7988, #39216, #38226, #84181, #76015, #22386, #13661 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.234508619761117277E-05, 4.370190546328693663E-05, 6.423309290663763063E-05, 8.416080901307881239E-05, 0.0001034426640163908936, 0.0001220538614379074622, 0.0001403618142760073597, 0.0001584534022805505007, 0.0001764955483670875070, 0.0001946270033858291386, 0.0002131061436272926651, 0.0002322220534159281750, 0.0002519406089841073676, 0.0002725210458542989974, 0.0002938778651199744699, 0.0003164559277781388660 ), + .UNSPECIFIED. ) ; +#26369 = EDGE_CURVE ( 'NONE', #43680, #93323, #94461, .T. ) ; +#26370 = STYLED_ITEM ( 'NONE', ( #70294 ), #18466 ) ; +#26371 = FACE_OUTER_BOUND ( 'NONE', #99237, .T. ) ; +#26372 = FILL_AREA_STYLE_COLOUR ( '', #32923 ) ; +#26373 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333323090, 0.09999999999999939493, 1.747825839084783216E-76 ) ) ; +#26374 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, 0.000000000000000000 ) ) ; +#26375 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#26376 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26377 = LINE ( 'NONE', #49862, #51125 ) ; +#26378 = VECTOR ( 'NONE', #5232, 1000.000000000000000 ) ; +#26379 = ORIENTED_EDGE ( 'NONE', *, *, #81945, .F. ) ; +#26380 = SURFACE_STYLE_FILL_AREA ( #81013 ) ; +#26381 = FILL_AREA_STYLE_COLOUR ( '', #17101 ) ; +#26382 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26384 = PRESENTATION_STYLE_ASSIGNMENT (( #57042 ) ) ; +#26383 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98072 ), #19872 ) ; +#26385 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96956, 'distance_accuracy_value', 'NONE'); +#26386 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#26387 = EDGE_CURVE ( 'NONE', #71259, #2990, #76092, .T. ) ; +#26388 = PLANE ( 'NONE', #48518 ) ; +#26389 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26390 = ORIENTED_EDGE ( 'NONE', *, *, #62542, .F. ) ; +#26391 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26392 = EDGE_CURVE ( 'NONE', #88427, #26081, #34717, .T. ) ; +#26393 = FILL_AREA_STYLE_COLOUR ( '', #75094 ) ; +#26394 = PRESENTATION_STYLE_ASSIGNMENT (( #70821 ) ) ; +#26395 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26396 = SURFACE_STYLE_USAGE ( .BOTH. , #19724 ) ; +#26397 = VECTOR ( 'NONE', #61703, 1000.000000000000000 ) ; +#26398 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26399 = FILL_AREA_STYLE_COLOUR ( '', #60381 ) ; +#26400 = PLANE ( 'NONE', #10759 ) ; +#26401 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#26402 = EDGE_CURVE ( 'NONE', #79320, #27113, #16329, .T. ) ; +#26403 = FILL_AREA_STYLE_COLOUR ( '', #73429 ) ; +#26404 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67164 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54414, #31410, #39079 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26405 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#26406 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26407 = EDGE_CURVE ( 'NONE', #21325, #16128, #7606, .T. ) ; +#26408 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#26409 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26410 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26411 = LINE ( 'NONE', #36084, #91838 ) ; +#26412 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#26413 = ORIENTED_EDGE ( 'NONE', *, *, #35712, .F. ) ; +#26414 = FILL_AREA_STYLE ('',( #50914 ) ) ; +#26415 = PRESENTATION_STYLE_ASSIGNMENT (( #57574 ) ) ; +#26416 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#26417 = CARTESIAN_POINT ( 'NONE', ( 10.36298512487495493, 4.857005124874956614, 0.8991599999999999593 ) ) ; +#26418 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18279 ) ) ; +#26419 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9701298701298698424, 0.8100000000000000533 ) ) ; +#26420 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26421 = EDGE_CURVE ( 'NONE', #12201, #95068, #93434, .T. ) ; +#26422 = ORIENTED_EDGE ( 'NONE', *, *, #999, .T. ) ; +#26423 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.000000000000000000 ) ) ; +#26424 = LINE ( 'NONE', #13017, #17121 ) ; +#26425 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26426 = SURFACE_STYLE_FILL_AREA ( #96329 ) ; +#26427 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -5.103411969279230082E-12 ) ) ; +#26428 = SURFACE_STYLE_USAGE ( .BOTH. , #3456 ) ; +#26429 = EDGE_CURVE ( 'NONE', #30264, #12592, #86311, .T. ) ; +#26430 = ADVANCED_FACE ( 'NONE', ( #25078 ), #86412, .F. ) ; +#26431 = EDGE_LOOP ( 'NONE', ( #30056, #37137, #88196, #63532 ) ) ; +#26432 = EDGE_LOOP ( 'NONE', ( #28858, #76754, #34923, #19967, #28466, #27586, #17164, #61149, #59680, #66872, #47193, #34373, #23846, #75236, #54684, #45476, #100063, #14699, #67724 ) ) ; +#26433 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65734 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55526, #65164, #18159 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26434 = STYLED_ITEM ( 'NONE', ( #21651 ), #34467 ) ; +#26435 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26436 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#26437 = ORIENTED_EDGE ( 'NONE', *, *, #4101, .T. ) ; +#26438 = SURFACE_SIDE_STYLE ('',( #35121 ) ) ; +#26439 = EDGE_CURVE ( 'NONE', #85325, #74727, #58736, .T. ) ; +#26440 = SURFACE_STYLE_USAGE ( .BOTH. , #32079 ) ; +#26441 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#26442 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26443 = VECTOR ( 'NONE', #66157, 1000.000000000000000 ) ; +#26444 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99696 ) ) ; +#26445 = PRODUCT_CONTEXT ( 'NONE', #49523, 'mechanical' ) ; +#26446 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#26447 = CARTESIAN_POINT ( 'NONE', ( 0.9697176841678971648, -1.376865229143298563, 0.8099999999997530287 ) ) ; +#26449 = ORIENTED_EDGE ( 'NONE', *, *, #21277, .T. ) ; +#26448 = VERTEX_POINT ( 'NONE', #11637 ) ; +#26450 = ADVANCED_FACE ( 'NONE', ( #89835 ), #74025, .F. ) ; +#26451 = VECTOR ( 'NONE', #99771, 1000.000000000000000 ) ; +#26452 = EDGE_LOOP ( 'NONE', ( #68473, #84343, #96697, #94467 ) ) ; +#26453 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55753 ), #57443 ) ; +#26454 = ORIENTED_EDGE ( 'NONE', *, *, #52679, .T. ) ; +#26455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95297, 'distance_accuracy_value', 'NONE'); +#26456 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86711 ), #80251 ) ; +#26457 = CARTESIAN_POINT ( 'NONE', ( 1.840728708308519979, -1.463352833475739967, 0.8299999999999999600 ) ) ; +#26459 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#26458 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26460 = ORIENTED_EDGE ( 'NONE', *, *, #12686, .T. ) ; +#26461 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.499999999999960032, -0.02000000000000000042 ) ) ; +#26462 = VERTEX_POINT ( 'NONE', #44352 ) ; +#26463 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.100000000000000089, 0.1829999999999959714 ) ) ; +#26464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5236 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24170, #84412, #55322 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26465 = EDGE_LOOP ( 'NONE', ( #91310, #18969, #52079, #93568 ) ) ; +#26466 = CYLINDRICAL_SURFACE ( 'NONE', #53433, 1.293024339031550118 ) ; +#26467 = VERTEX_POINT ( 'NONE', #28553 ) ; +#26468 = EDGE_CURVE ( 'NONE', #56225, #71271, #67833, .T. ) ; +#26469 = ORIENTED_EDGE ( 'NONE', *, *, #45015, .F. ) ; +#26470 = EDGE_CURVE ( 'NONE', #30669, #26074, #53553, .T. ) ; +#26471 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26473 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#26472 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#26474 = PRESENTATION_STYLE_ASSIGNMENT (( #24480 ) ) ; +#26475 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#26477 = ORIENTED_EDGE ( 'NONE', *, *, #57209, .F. ) ; +#26476 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26478 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26479 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#26480 = CARTESIAN_POINT ( 'NONE', ( -0.2957352054868390145, -1.084890943604200020, 0.8100000000000000533 ) ) ; +#26481 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#26482 = EDGE_LOOP ( 'NONE', ( #26669, #86585, #100790, #62418 ) ) ; +#26484 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26483 = PRESENTATION_STYLE_ASSIGNMENT (( #26987 ) ) ; +#26485 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26486 = VERTEX_POINT ( 'NONE', #59245 ) ; +#26487 = ORIENTED_EDGE ( 'NONE', *, *, #99433, .T. ) ; +#26488 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26489 = FACE_OUTER_BOUND ( 'NONE', #6716, .T. ) ; +#26490 = ADVANCED_FACE ( 'NONE', ( #14185 ), #52553, .T. ) ; +#26491 = SURFACE_SIDE_STYLE ('',( #42312 ) ) ; +#26493 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98184 ), #13414 ) ; +#26492 = CARTESIAN_POINT ( 'NONE', ( -0.6674107142857140795, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#26494 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26495 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26496 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52159, 'distance_accuracy_value', 'NONE'); +#26497 = EDGE_LOOP ( 'NONE', ( #80191, #94074, #70259, #6643 ) ) ; +#26498 = ORIENTED_EDGE ( 'NONE', *, *, #29532, .F. ) ; +#26499 = VECTOR ( 'NONE', #19255, 1000.000000000000000 ) ; +#26500 = AXIS2_PLACEMENT_3D ( 'NONE', #23552, #86839, #16853 ) ; +#26501 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#26502 = LINE ( 'NONE', #2509, #22068 ) ; +#26503 = CARTESIAN_POINT ( 'NONE', ( 1.425641884052289976, -1.263266231710209908, 0.8299999999999999600 ) ) ; +#26504 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#26505 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26506 = STYLED_ITEM ( 'NONE', ( #28500 ), #19227 ) ; +#26507 = STYLED_ITEM ( 'NONE', ( #54908 ), #35378 ) ; +#26508 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26509 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26510 = ORIENTED_EDGE ( 'NONE', *, *, #47052, .F. ) ; +#26511 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000541, 0.2350000000000000144 ) ) ; +#26513 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70499 ), #18300 ) ; +#26512 = PRESENTATION_STYLE_ASSIGNMENT (( #65295 ) ) ; +#26514 = SURFACE_STYLE_FILL_AREA ( #2519 ) ; +#26515 = SURFACE_SIDE_STYLE ('',( #96414 ) ) ; +#26516 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84448 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #575, #93968, #53218 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26518 = CIRCLE ( 'NONE', #39533, 0.009999999999999998473 ) ; +#26519 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26520 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79135 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48782, #64583, #10354 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26521 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#26522 = LINE ( 'NONE', #95917, #61483 ) ; +#26523 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26524 = EDGE_CURVE ( 'NONE', #91699, #61010, #37244, .T. ) ; +#26525 = VECTOR ( 'NONE', #68609, 1000.000000000000000 ) ; +#26526 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.000000000000000000 ) ) ; +#26527 = VECTOR ( 'NONE', #59190, 1000.000000000000000 ) ; +#26528 = ADVANCED_FACE ( 'NONE', ( #20383 ), #59755, .T. ) ; +#26529 = ORIENTED_EDGE ( 'NONE', *, *, #88302, .F. ) ; +#26530 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#26531 = CARTESIAN_POINT ( 'NONE', ( 1.601121020982049892, -0.9216047924506349798, 0.8100000000000000533 ) ) ; +#26532 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#26533 = ORIENTED_EDGE ( 'NONE', *, *, #75676, .T. ) ; +#26534 = SURFACE_STYLE_FILL_AREA ( #96430 ) ; +#26535 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.5000000000000000000, 0.1829999999999790128 ) ) ; +#26536 = FILL_AREA_STYLE_COLOUR ( '', #79447 ) ; +#26537 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8490 ), #83596 ) ; +#26538 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26539 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26540 = STYLED_ITEM ( 'NONE', ( #75258 ), #25437 ) ; +#26541 = ORIENTED_EDGE ( 'NONE', *, *, #47950, .F. ) ; +#26542 = EDGE_CURVE ( 'NONE', #92928, #50063, #98416, .T. ) ; +#26543 = EDGE_LOOP ( 'NONE', ( #89956, #32835, #14963, #18219 ) ) ; +#26544 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#26545 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23919, 'distance_accuracy_value', 'NONE'); +#26546 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26547 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26548 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#26549 = LINE ( 'NONE', #58220, #51092 ) ; +#26550 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#26551 = FACE_OUTER_BOUND ( 'NONE', #89277, .T. ) ; +#26552 = FILL_AREA_STYLE ('',( #18346 ) ) ; +#26553 = FILL_AREA_STYLE_COLOUR ( '', #13517 ) ; +#26554 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13403 ) ) ; +#26555 = FILL_AREA_STYLE_COLOUR ( '', #48511 ) ; +#26556 = ADVANCED_FACE ( 'NONE', ( #22922 ), #6986, .F. ) ; +#26557 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26558 = ORIENTED_EDGE ( 'NONE', *, *, #19461, .T. ) ; +#26559 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26560 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91745 ) ) ; +#26561 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26562 = EDGE_LOOP ( 'NONE', ( #39201, #27461, #52580, #72244 ) ) ; +#26563 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909090190, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#26564 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2303 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35652, #92228, #36647 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26565 = SURFACE_SIDE_STYLE ('',( #80697 ) ) ; +#26566 = CARTESIAN_POINT ( 'NONE', ( -1.143806093516799960, -0.9548508715965600135, 0.8299999999999999600 ) ) ; +#26567 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#26568 = LINE ( 'NONE', #49554, #58852 ) ; +#26570 = ORIENTED_EDGE ( 'NONE', *, *, #91649, .F. ) ; +#26569 = VERTEX_POINT ( 'NONE', #69315 ) ; +#26571 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26572 = EDGE_CURVE ( 'NONE', #99316, #58744, #7990, .T. ) ; +#26573 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26574 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#26575 = ORIENTED_EDGE ( 'NONE', *, *, #63716, .F. ) ; +#26576 = VECTOR ( 'NONE', #10198, 1000.000000000000114 ) ; +#26577 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666626639, -2.500000000000000000, 0.000000000000000000 ) ) ; +#26578 = ORIENTED_EDGE ( 'NONE', *, *, #91595, .T. ) ; +#26579 = EDGE_CURVE ( 'NONE', #85903, #94599, #54222, .T. ) ; +#26580 = EDGE_LOOP ( 'NONE', ( #58356, #25380, #69985, #66880 ) ) ; +#26581 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#26582 = FACE_OUTER_BOUND ( 'NONE', #57459, .T. ) ; +#26583 = AXIS2_PLACEMENT_3D ( 'NONE', #55770, #85884, #78241 ) ; +#26584 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26586 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26585 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26587 = EDGE_LOOP ( 'NONE', ( #13674, #40174, #29910, #40968 ) ) ; +#26588 = ORIENTED_EDGE ( 'NONE', *, *, #77244, .T. ) ; +#26589 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26590 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96582 ) ) ; +#26591 = VERTEX_POINT ( 'NONE', #86701 ) ; +#26592 = FILL_AREA_STYLE ('',( #34266 ) ) ; +#26593 = EDGE_CURVE ( 'NONE', #45870, #58394, #77514, .T. ) ; +#26594 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52675 ), #8536 ) ; +#26595 = EDGE_CURVE ( 'NONE', #31896, #68541, #85685, .T. ) ; +#26596 = LINE ( 'NONE', #35282, #78568 ) ; +#26597 = STYLED_ITEM ( 'NONE', ( #31284 ), #96600 ) ; +#26600 = ADVANCED_FACE ( 'NONE', ( #62235 ), #93311, .F. ) ; +#26599 = VERTEX_POINT ( 'NONE', #84680 ) ; +#26598 = LINE ( 'NONE', #12695, #88531 ) ; +#26601 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91711 ), #72205 ) ; +#26602 = ADVANCED_FACE ( 'NONE', ( #5358 ), #29870, .T. ) ; +#26603 = LINE ( 'NONE', #17392, #67049 ) ; +#26604 = VECTOR ( 'NONE', #47930, 1000.000000000000000 ) ; +#26605 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.4333333333333353465, 0.000000000000000000 ) ) ; +#26606 = VERTEX_POINT ( 'NONE', #14013 ) ; +#26607 = CARTESIAN_POINT ( 'NONE', ( -0.1052747236373319933, -1.219598171061480052, 0.8100000000000000533 ) ) ; +#26608 = PLANE ( 'NONE', #21640 ) ; +#26609 = ORIENTED_EDGE ( 'NONE', *, *, #773, .F. ) ; +#26610 = LINE ( 'NONE', #49592, #5645 ) ; +#26611 = ADVANCED_FACE ( 'NONE', ( #44190 ), #5853, .T. ) ; +#26612 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26613 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#26614 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#26615 = EDGE_CURVE ( 'NONE', #80372, #20411, #98746, .T. ) ; +#26616 = SURFACE_STYLE_FILL_AREA ( #11179 ) ; +#26617 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26619 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#26618 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26620 = LINE ( 'NONE', #47561, #63772 ) ; +#26621 = ORIENTED_EDGE ( 'NONE', *, *, #66176, .T. ) ; +#26622 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#26623 = FACE_OUTER_BOUND ( 'NONE', #58772, .T. ) ; +#26624 = EDGE_LOOP ( 'NONE', ( #32210, #58133, #48562, #40986 ) ) ; +#26625 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15096 ) ) ; +#26626 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26627 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26628 = CARTESIAN_POINT ( 'NONE', ( -0.2587106361308370017, -1.457888621141530061, 0.8299999999999999600 ) ) ; +#26629 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26630 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689420, 0.4808578643762690952, 0.2499999999999999445 ) ) ; +#26631 = CIRCLE ( 'NONE', #33100, 0.01000000000000002623 ) ; +#26632 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #53415, #84544, #30393, #6849 ), + .UNSPECIFIED., .F., .F. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.3333333333333333703, 0.3333333333333333703, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#26633 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, 0.1400000000000000411 ) ) ; +#26634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26635 = SURFACE_STYLE_USAGE ( .BOTH. , #11199 ) ; +#26636 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#26637 = LINE ( 'NONE', #4136, #90375 ) ; +#26638 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70627 ) ) ; +#26639 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37553 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32829, #32326, #85424 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26640 = SURFACE_STYLE_FILL_AREA ( #89407 ) ; +#26641 = ORIENTED_EDGE ( 'NONE', *, *, #55281, .T. ) ; +#26642 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26644 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26643 = VECTOR ( 'NONE', #18551, 1000.000000000000000 ) ; +#26645 = FACE_OUTER_BOUND ( 'NONE', #46244, .T. ) ; +#26646 = ADVANCED_FACE ( 'NONE', ( #30357 ), #16001, .T. ) ; +#26647 = PLANE ( 'NONE', #76165 ) ; +#26648 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75530 ) ) ; +#26649 = ADVANCED_FACE ( 'NONE', ( #49205 ), #54857, .T. ) ; +#26651 = ORIENTED_EDGE ( 'NONE', *, *, #41908, .F. ) ; +#26650 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86913 ) ) ; +#26652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26653 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.000000000000000000 ) ) ; +#26654 = FILL_AREA_STYLE ('',( #96548 ) ) ; +#26655 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26656 = SURFACE_STYLE_FILL_AREA ( #88418 ) ; +#26657 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26658 = SURFACE_STYLE_USAGE ( .BOTH. , #57302 ) ; +#26659 = VECTOR ( 'NONE', #87779, 1000.000000000000000 ) ; +#26660 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#26662 = FACE_OUTER_BOUND ( 'NONE', #34657, .T. ) ; +#26663 = FACE_OUTER_BOUND ( 'NONE', #31105, .T. ) ; +#26665 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26664 = CIRCLE ( 'NONE', #96722, 0.1999999999999996503 ) ; +#26666 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11031, 'distance_accuracy_value', 'NONE'); +#26667 = VECTOR ( 'NONE', #97929, 1000.000000000000000 ) ; +#26668 = SURFACE_SIDE_STYLE ('',( #35841 ) ) ; +#26669 = ORIENTED_EDGE ( 'NONE', *, *, #22303, .F. ) ; +#26670 = LINE ( 'NONE', #48126, #84056 ) ; +#26672 = EDGE_LOOP ( 'NONE', ( #72132, #62362, #56642 ) ) ; +#26671 = VECTOR ( 'NONE', #71412, 1000.000000000000114 ) ; +#26673 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#26674 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40835, 'distance_accuracy_value', 'NONE'); +#26675 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41720, 'distance_accuracy_value', 'NONE'); +#26676 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#26677 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26678 = CARTESIAN_POINT ( 'NONE', ( -0.1914460425574669999, -0.9925253384799729295, 0.8299999999999999600 ) ) ; +#26679 = FACE_OUTER_BOUND ( 'NONE', #76143, .T. ) ; +#26680 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70660 ) ) ; +#26681 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.50000000000000000, 0.000000000000000000 ) ) ; +#26682 = PRESENTATION_STYLE_ASSIGNMENT (( #24680 ) ) ; +#26683 = ORIENTED_EDGE ( 'NONE', *, *, #18859, .F. ) ; +#26684 = EDGE_CURVE ( 'NONE', #45850, #38717, #94621, .T. ) ; +#26685 = FILL_AREA_STYLE ('',( #80298 ) ) ; +#26686 = EDGE_LOOP ( 'NONE', ( #49633, #25452, #99919, #19856 ) ) ; +#26687 = CYLINDRICAL_SURFACE ( 'NONE', #6514, 0.05000000000000012768 ) ; +#26688 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57687 ), #49492 ) ; +#26689 = PRESENTATION_STYLE_ASSIGNMENT (( #96580 ) ) ; +#26690 = ORIENTED_EDGE ( 'NONE', *, *, #4740, .T. ) ; +#26691 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26692 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#26693 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26694 = FILL_AREA_STYLE_COLOUR ( '', #67728 ) ; +#26695 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26697 = ORIENTED_EDGE ( 'NONE', *, *, #6582, .T. ) ; +#26696 = STYLED_ITEM ( 'NONE', ( #330 ), #70898 ) ; +#26698 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26699 = LINE ( 'NONE', #56358, #99945 ) ; +#26700 = EDGE_LOOP ( 'NONE', ( #59972, #97589, #29926, #32941 ) ) ; +#26701 = PRESENTATION_STYLE_ASSIGNMENT (( #88974 ) ) ; +#26702 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65760 ), #82094 ) ; +#26703 = ORIENTED_EDGE ( 'NONE', *, *, #79613, .F. ) ; +#26704 = VERTEX_POINT ( 'NONE', #39012 ) ; +#26705 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#26706 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#26707 = PLANE ( 'NONE', #86434 ) ; +#26708 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#26709 = CARTESIAN_POINT ( 'NONE', ( -0.4484724165379589955, -1.115587024626630175, 0.8100000000000000533 ) ) ; +#26710 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#26711 = FACE_OUTER_BOUND ( 'NONE', #39028, .T. ) ; +#26712 = VERTEX_POINT ( 'NONE', #94095 ) ; +#26714 = ORIENTED_EDGE ( 'NONE', *, *, #92429, .T. ) ; +#26713 = ORIENTED_EDGE ( 'NONE', *, *, #86107, .F. ) ; +#26715 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26716 = ORIENTED_EDGE ( 'NONE', *, *, #66126, .T. ) ; +#26717 = VECTOR ( 'NONE', #67887, 1000.000000000000114 ) ; +#26718 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#26719 = VERTEX_POINT ( 'NONE', #79847 ) ; +#26721 = ORIENTED_EDGE ( 'NONE', *, *, #93847, .F. ) ; +#26720 = CYLINDRICAL_SURFACE ( 'NONE', #21537, 0.2500000000000000000 ) ; +#26722 = ADVANCED_FACE ( 'NONE', ( #40545 ), #1737, .F. ) ; +#26723 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#26724 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34671 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90026, #11341, #27273 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26725 = SURFACE_STYLE_USAGE ( .BOTH. , #28221 ) ; +#26726 = ORIENTED_EDGE ( 'NONE', *, *, #61695, .F. ) ; +#26727 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26728 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26729 = FACE_OUTER_BOUND ( 'NONE', #85632, .T. ) ; +#26730 = VERTEX_POINT ( 'NONE', #27241 ) ; +#26731 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26732 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8100000000000001643 ) ) ; +#26733 = STYLED_ITEM ( 'NONE', ( #21528 ), #38050 ) ; +#26734 = FILL_AREA_STYLE ('',( #58398 ) ) ; +#26735 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26736 = CARTESIAN_POINT ( 'NONE', ( -1.429289321881344943, 0.7099999999999999645, 0.9636038969321073511 ) ) ; +#26737 = CARTESIAN_POINT ( 'NONE', ( 0.06449442099368349335, -1.103202958186300320, 0.8300000000000002931 ) ) ; +#26738 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65625 ) ) ; +#26739 = EDGE_CURVE ( 'NONE', #5408, #44001, #4233, .T. ) ; +#26740 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#26741 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#26742 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8991599999999999593 ) ) ; +#26743 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26744 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#26745 = FACE_OUTER_BOUND ( 'NONE', #79426, .T. ) ; +#26746 = STYLED_ITEM ( 'NONE', ( #20670 ), #11805 ) ; +#26747 = PLANE ( 'NONE', #16100 ) ; +#26749 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26748 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.000000000000000000 ) ) ; +#26750 = FILL_AREA_STYLE ('',( #11314 ) ) ; +#26751 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#26752 = VECTOR ( 'NONE', #94954, 1000.000000000000000 ) ; +#26753 = CARTESIAN_POINT ( 'NONE', ( 1.080509293578989949, -0.9076590548536891401, 0.8299999999999999600 ) ) ; +#26754 = ORIENTED_EDGE ( 'NONE', *, *, #15769, .F. ) ; +#26755 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26756 = PLANE ( 'NONE', #82952 ) ; +#26757 = CARTESIAN_POINT ( 'NONE', ( 5.080897750250088052, 3.266015249749912197, 0.8991599999999999593 ) ) ; +#26758 = CARTESIAN_POINT ( 'NONE', ( 4.420082539177975001, 1.449283853103374042, -11.91176989140982023 ) ) ; +#26759 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#26760 = ORIENTED_EDGE ( 'NONE', *, *, #5193, .F. ) ; +#26761 = ADVANCED_FACE ( 'NONE', ( #26230 ), #72673, .T. ) ; +#26762 = CARTESIAN_POINT ( 'NONE', ( -0.9152290605710889926, -1.296821915455180108, 0.8300000000000002931 ) ) ; +#26763 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26764 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#26766 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26765 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#26767 = CARTESIAN_POINT ( 'NONE', ( 1.608893861054889962, -1.000931601726380071, 0.8299999999999999600 ) ) ; +#26768 = CARTESIAN_POINT ( 'NONE', ( -0.1995248675705779962, -1.417598257925390293, 0.8299999999999999600 ) ) ; +#26769 = LINE ( 'NONE', #89044, #84511 ) ; +#26770 = AXIS2_PLACEMENT_3D ( 'NONE', #91959, #21518, #90461 ) ; +#26771 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#26772 = SURFACE_STYLE_FILL_AREA ( #96667 ) ; +#26773 = EDGE_CURVE ( 'NONE', #63998, #64466, #3728, .T. ) ; +#26774 = ORIENTED_EDGE ( 'NONE', *, *, #5612, .F. ) ; +#26775 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26776 = SURFACE_SIDE_STYLE ('',( #82404 ) ) ; +#26777 = LINE ( 'NONE', #82896, #60760 ) ; +#26778 = LINE ( 'NONE', #57947, #40407 ) ; +#26779 = LINE ( 'NONE', #43074, #5664 ) ; +#26780 = SURFACE_SIDE_STYLE ('',( #66073 ) ) ; +#26781 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63593 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64458, #96060, #41482 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26782 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44660 ), #82243 ) ; +#26783 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#26784 = SURFACE_STYLE_USAGE ( .BOTH. , #56937 ) ; +#26785 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61805, 'distance_accuracy_value', 'NONE'); +#26786 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#26787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26788 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#26789 = STYLED_ITEM ( 'NONE', ( #46932 ), #76519 ) ; +#26790 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077920276, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#26791 = ORIENTED_EDGE ( 'NONE', *, *, #10546, .T. ) ; +#26792 = SURFACE_STYLE_USAGE ( .BOTH. , #8844 ) ; +#26793 = ORIENTED_EDGE ( 'NONE', *, *, #35211, .T. ) ; +#26794 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86466, 'distance_accuracy_value', 'NONE'); +#26796 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6092, 'distance_accuracy_value', 'NONE'); +#26797 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#26798 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, 3.500000000000000444, 0.000000000000000000 ) ) ; +#26799 = FACE_OUTER_BOUND ( 'NONE', #37370, .T. ) ; +#26800 = FACE_OUTER_BOUND ( 'NONE', #49429, .T. ) ; +#26801 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#26802 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#26803 = STYLED_ITEM ( 'NONE', ( #64564 ), #21502 ) ; +#26804 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26805 = EDGE_LOOP ( 'NONE', ( #61771, #96574, #71425, #63264 ) ) ; +#26806 = PLANE ( 'NONE', #81375 ) ; +#26807 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55083, 'distance_accuracy_value', 'NONE'); +#26810 = STYLED_ITEM ( 'NONE', ( #36431 ), #28982 ) ; +#26809 = AXIS2_PLACEMENT_3D ( 'NONE', #66379, #58748, #41405 ) ; +#26808 = FACE_OUTER_BOUND ( 'NONE', #49284, .T. ) ; +#26811 = VECTOR ( 'NONE', #1002, 1000.000000000000000 ) ; +#26812 = SURFACE_STYLE_USAGE ( .BOTH. , #79415 ) ; +#26813 = VERTEX_POINT ( 'NONE', #34901 ) ; +#26814 = FILL_AREA_STYLE ('',( #80424 ) ) ; +#26815 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61060 ) ) ; +#26816 = EDGE_CURVE ( 'NONE', #63874, #66295, #10800, .T. ) ; +#26817 = VECTOR ( 'NONE', #67461, 1000.000000000000000 ) ; +#26818 = SURFACE_STYLE_FILL_AREA ( #95696 ) ; +#26819 = SURFACE_STYLE_FILL_AREA ( #96703 ) ; +#26820 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#26821 = ORIENTED_EDGE ( 'NONE', *, *, #69799, .F. ) ; +#26822 = AXIS2_PLACEMENT_3D ( 'NONE', #8126, #55716, #25580 ) ; +#26823 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.266666666666653285, 0.000000000000000000 ) ) ; +#26824 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10590, 'distance_accuracy_value', 'NONE'); +#26825 = PRESENTATION_STYLE_ASSIGNMENT (( #97220 ) ) ; +#26826 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90344 ), #54514 ) ; +#26827 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#26828 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#26829 = ADVANCED_FACE ( 'NONE', ( #19550 ), #98087, .T. ) ; +#26830 = ORIENTED_EDGE ( 'NONE', *, *, #16160, .T. ) ; +#26831 = ADVANCED_FACE ( 'NONE', ( #84833 ), #76678, .F. ) ; +#26832 = SURFACE_STYLE_FILL_AREA ( #95204 ) ; +#26833 = FACE_OUTER_BOUND ( 'NONE', #48335, .T. ) ; +#26834 = PRESENTATION_STYLE_ASSIGNMENT (( #2337 ) ) ; +#26835 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13684 ), #92015 ) ; +#26836 = FILL_AREA_STYLE_COLOUR ( '', #85291 ) ; +#26837 = LINE ( 'NONE', #44607, #1532 ) ; +#26838 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8705 ), #36598 ) ; +#26839 = SURFACE_STYLE_USAGE ( .BOTH. , #80968 ) ; +#26840 = AXIS2_PLACEMENT_3D ( 'NONE', #22323, #93741, #69779 ) ; +#26841 = ORIENTED_EDGE ( 'NONE', *, *, #61336, .F. ) ; +#26843 = VERTEX_POINT ( 'NONE', #6657 ) ; +#26842 = PRESENTATION_STYLE_ASSIGNMENT (( #65614 ) ) ; +#26844 = AXIS2_PLACEMENT_3D ( 'NONE', #59326, #53637, #84762 ) ; +#26845 = PLANE ( 'NONE', #90058 ) ; +#26847 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#26846 = STYLED_ITEM ( 'NONE', ( #24593 ), #53452 ) ; +#26848 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#26849 = FACE_OUTER_BOUND ( 'NONE', #36725, .T. ) ; +#26850 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#26851 = ORIENTED_EDGE ( 'NONE', *, *, #26981, .F. ) ; +#26852 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#26853 = STYLED_ITEM ( 'NONE', ( #60065 ), #88748 ) ; +#26854 = VERTEX_POINT ( 'NONE', #7149 ) ; +#26855 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000021, 0.2250000000000000333 ) ) ; +#26856 = EDGE_LOOP ( 'NONE', ( #50478, #84229, #83249, #74411 ) ) ; +#26857 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70859 ) ) ; +#26858 = VERTEX_POINT ( 'NONE', #21551 ) ; +#26859 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26860 = EDGE_CURVE ( 'NONE', #16362, #97167, #75678, .T. ) ; +#26862 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26861 = FILL_AREA_STYLE_COLOUR ( '', #54354 ) ; +#26863 = FACE_OUTER_BOUND ( 'NONE', #77127, .T. ) ; +#26864 = AXIS2_PLACEMENT_3D ( 'NONE', #59634, #12021, #3464 ) ; +#26865 = ORIENTED_EDGE ( 'NONE', *, *, #69740, .T. ) ; +#26866 = PLANE ( 'NONE', #75208 ) ; +#26867 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44737 ) ) ; +#26868 = ORIENTED_EDGE ( 'NONE', *, *, #79337, .F. ) ; +#26869 = ORIENTED_EDGE ( 'NONE', *, *, #24316, .F. ) ; +#26870 = VECTOR ( 'NONE', #91054, 1000.000000000000000 ) ; +#26871 = FACE_OUTER_BOUND ( 'NONE', #25582, .T. ) ; +#26872 = CARTESIAN_POINT ( 'NONE', ( -0.9900897613018839749, -1.321802795360440319, 0.8100000000000000533 ) ) ; +#26873 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#26874 = AXIS2_PLACEMENT_3D ( 'NONE', #18791, #48964, #25490 ) ; +#26875 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#26876 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#26877 = LINE ( 'NONE', #73338, #5530 ) ; +#26878 = FILL_AREA_STYLE ('',( #96768 ) ) ; +#26879 = VECTOR ( 'NONE', #57554, 1000.000000000000000 ) ; +#26880 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155850987, 0.8100000000000249223 ) ) ; +#26881 = ORIENTED_EDGE ( 'NONE', *, *, #43825, .F. ) ; +#26882 = EDGE_CURVE ( 'NONE', #97102, #76877, #46001, .T. ) ; +#26883 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26884 = SURFACE_SIDE_STYLE ('',( #13463 ) ) ; +#26886 = SURFACE_STYLE_FILL_AREA ( #96777 ) ; +#26885 = PRESENTATION_STYLE_ASSIGNMENT (( #71314 ) ) ; +#26887 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87147 ), #49708 ) ; +#26888 = VECTOR ( 'NONE', #26618, 1000.000000000000000 ) ; +#26889 = FILL_AREA_STYLE ('',( #49875 ) ) ; +#26890 = SURFACE_STYLE_USAGE ( .BOTH. , #72315 ) ; +#26891 = FILL_AREA_STYLE ('',( #65171 ) ) ; +#26892 = EDGE_CURVE ( 'NONE', #9173, #30456, #92963, .T. ) ; +#26893 = EDGE_LOOP ( 'NONE', ( #97245, #26167, #18776, #94340 ) ) ; +#26894 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#26895 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#26896 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.569275000000000198, 0.8648700000000000276 ) ) ; +#26897 = CARTESIAN_POINT ( 'NONE', ( 0.3953060575754059891, -1.200834233358659908, 0.8300000000000015143 ) ) ; +#26898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63130, 'distance_accuracy_value', 'NONE'); +#26899 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#26900 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#26901 = SURFACE_STYLE_FILL_AREA ( #88663 ) ; +#26902 = FILL_AREA_STYLE ('',( #3896 ) ) ; +#26903 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#26904 = LINE ( 'NONE', #3898, #14826 ) ; +#26905 = SURFACE_SIDE_STYLE ('',( #4884 ) ) ; +#26906 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#26907 = PLANE ( 'NONE', #22727 ) ; +#26908 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33394 ) ) ; +#26909 = PRESENTATION_STYLE_ASSIGNMENT (( #18703 ) ) ; +#26910 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4849999999999999867, -0.2399999999999999911 ) ) ; +#26911 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#26912 = SURFACE_SIDE_STYLE ('',( #50424 ) ) ; +#26913 = FILL_AREA_STYLE_COLOUR ( '', #82116 ) ; +#26914 = AXIS2_PLACEMENT_3D ( 'NONE', #50306, #10863, #66574 ) ; +#26915 = FILL_AREA_STYLE ('',( #35088 ) ) ; +#26916 = SURFACE_STYLE_USAGE ( .BOTH. , #50426 ) ; +#26917 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#26918 = EDGE_LOOP ( 'NONE', ( #38886, #96853, #87583, #63992 ) ) ; +#26919 = FILL_AREA_STYLE_COLOUR ( '', #99092 ) ; +#26920 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80890, 'distance_accuracy_value', 'NONE'); +#26921 = FACE_OUTER_BOUND ( 'NONE', #92678, .T. ) ; +#26922 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59143, 'distance_accuracy_value', 'NONE'); +#26923 = SURFACE_STYLE_FILL_AREA ( #95302 ) ; +#26924 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22637 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55987, #40148, #10391 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26925 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26926 = AXIS2_PLACEMENT_3D ( 'NONE', #94995, #54745, #63414 ) ; +#26927 = EDGE_CURVE ( 'NONE', #93165, #34867, #44031, .T. ) ; +#26928 = STYLED_ITEM ( 'NONE', ( #90984 ), #77115 ) ; +#26929 = ORIENTED_EDGE ( 'NONE', *, *, #78512, .F. ) ; +#26930 = LINE ( 'NONE', #58101, #28577 ) ; +#26931 = FILL_AREA_STYLE_COLOUR ( '', #61881 ) ; +#26932 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70782, 'distance_accuracy_value', 'NONE'); +#26933 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4808578643762690952, 0.2399999999999999911 ) ) ; +#26934 = STYLED_ITEM ( 'NONE', ( #91553 ), #20339 ) ; +#26935 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22688, 'distance_accuracy_value', 'NONE'); +#26936 = VECTOR ( 'NONE', #29036, 1000.000000000000000 ) ; +#26937 = SURFACE_STYLE_USAGE ( .BOTH. , #64222 ) ; +#26938 = ADVANCED_FACE ( 'NONE', ( #5687 ), #69500, .T. ) ; +#26939 = VERTEX_POINT ( 'NONE', #60889 ) ; +#26940 = ORIENTED_EDGE ( 'NONE', *, *, #43241, .T. ) ; +#26941 = ADVANCED_FACE ( 'NONE', ( #91992 ), #47552, .F. ) ; +#26943 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85495 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80485, #81522, #57026 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#26942 = STYLED_ITEM ( 'NONE', ( #83848 ), #38736 ) ; +#26944 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82334 ), #61205 ) ; +#26945 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#26946 = VERTEX_POINT ( 'NONE', #39900 ) ; +#26947 = ADVANCED_FACE ( 'NONE', ( #62905 ), #71558, .T. ) ; +#26948 = SURFACE_SIDE_STYLE ('',( #10491 ) ) ; +#26949 = FACE_OUTER_BOUND ( 'NONE', #76161, .T. ) ; +#26950 = FILL_AREA_STYLE ('',( #97345 ) ) ; +#26952 = ORIENTED_EDGE ( 'NONE', *, *, #84671, .F. ) ; +#26951 = ORIENTED_EDGE ( 'NONE', *, *, #91150, .T. ) ; +#26953 = VECTOR ( 'NONE', #30954, 1000.000000000000114 ) ; +#26954 = VERTEX_POINT ( 'NONE', #63897 ) ; +#26955 = VERTEX_POINT ( 'NONE', #24622 ) ; +#26956 = PLANE ( 'NONE', #89948 ) ; +#26958 = EDGE_CURVE ( 'NONE', #59629, #30660, #93965, .T. ) ; +#26957 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26959 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#26960 = CARTESIAN_POINT ( 'NONE', ( 0.5034558050616539937, -0.9558425862917759863, 0.8100000000000000533 ) ) ; +#26961 = EDGE_LOOP ( 'NONE', ( #67740, #22038, #58662, #59137, #68763, #81027 ) ) ; +#26962 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#26963 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#26964 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70971 ) ) ; +#26965 = ORIENTED_EDGE ( 'NONE', *, *, #62431, .T. ) ; +#26966 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#26967 = ORIENTED_EDGE ( 'NONE', *, *, #2252, .F. ) ; +#26968 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26969 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26970 = ORIENTED_EDGE ( 'NONE', *, *, #78443, .T. ) ; +#26971 = VERTEX_POINT ( 'NONE', #55738 ) ; +#26972 = ADVANCED_FACE ( 'NONE', ( #56257 ), #87361, .F. ) ; +#26973 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#26974 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26975 = SURFACE_STYLE_USAGE ( .BOTH. , #43771 ) ; +#26976 = ADVANCED_FACE ( 'NONE', ( #41426 ), #26110, .T. ) ; +#26977 = STYLED_ITEM ( 'NONE', ( #2600 ), #72097 ) ; +#26979 = ORIENTED_EDGE ( 'NONE', *, *, #56206, .F. ) ; +#26978 = SURFACE_SIDE_STYLE ('',( #34646 ) ) ; +#26980 = VERTEX_POINT ( 'NONE', #96504 ) ; +#26981 = EDGE_CURVE ( 'NONE', #17103, #66284, #12733, .T. ) ; +#26982 = CARTESIAN_POINT ( 'NONE', ( -0.2066711868101530070, -0.9216047924506359790, 0.8100000000000000533 ) ) ; +#26983 = AXIS2_PLACEMENT_3D ( 'NONE', #17955, #59352, #27687 ) ; +#26984 = CARTESIAN_POINT ( 'NONE', ( 4.847552500500175832, 4.418599499499825889, 0.8991599999999999593 ) ) ; +#26985 = VECTOR ( 'NONE', #81017, 1000.000000000000114 ) ; +#26986 = ORIENTED_EDGE ( 'NONE', *, *, #4969, .T. ) ; +#26988 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#26987 = SURFACE_STYLE_USAGE ( .BOTH. , #81117 ) ; +#26989 = EDGE_LOOP ( 'NONE', ( #57359, #49356, #58350, #2857 ) ) ; +#26990 = ORIENTED_EDGE ( 'NONE', *, *, #40960, .T. ) ; +#26992 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#26991 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #24720 ) ) ; +#26993 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#26994 = STYLED_ITEM ( 'NONE', ( #84700 ), #82565 ) ; +#26995 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#26996 = SURFACE_STYLE_USAGE ( .BOTH. , #34664 ) ; +#26997 = STYLED_ITEM ( 'NONE', ( #39010 ), #78264 ) ; +#26998 = AXIS2_PLACEMENT_3D ( 'NONE', #46731, #77896, #36606 ) ; +#26999 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#27000 = PRODUCT ( 'Submodel-XTAL3225_part_XTAL3225', 'Submodel-XTAL3225_part_XTAL3225', '', ( #93803 ) ) ; +#27001 = PLANE ( 'NONE', #96598 ) ; +#27002 = EDGE_LOOP ( 'NONE', ( #52040, #1925, #17002, #614 ) ) ; +#27003 = EDGE_CURVE ( 'NONE', #65042, #33782, #93043, .T. ) ; +#27004 = VECTOR ( 'NONE', #10644, 1000.000000000000114 ) ; +#27005 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#27006 = ORIENTED_EDGE ( 'NONE', *, *, #82396, .F. ) ; +#27007 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#27008 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.500000000000000444, 0.000000000000000000 ) ) ; +#27009 = CARTESIAN_POINT ( 'NONE', ( 1.337010325208910277, -1.189797473215369994, 0.8100000000000000533 ) ) ; +#27010 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64279 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96055, #56321, #49648 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27012 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82624 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58479, #25427, #48896 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27011 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27013 = FILL_AREA_STYLE_COLOUR ( '', #85901 ) ; +#27014 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#27015 = EDGE_CURVE ( 'NONE', #32396, #28694, #26610, .T. ) ; +#27016 = ORIENTED_EDGE ( 'NONE', *, *, #8795, .T. ) ; +#27018 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3952 ), #66137 ) ; +#27017 = VECTOR ( 'NONE', #90879, 1000.000000000000000 ) ; +#27019 = FILL_AREA_STYLE_COLOUR ( '', #52530 ) ; +#27020 = LINE ( 'NONE', #90795, #84688 ) ; +#27021 = VECTOR ( 'NONE', #46040, 1000.000000000000000 ) ; +#27022 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#27023 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#27024 = SURFACE_SIDE_STYLE ('',( #59701 ) ) ; +#27025 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#27026 = ADVANCED_FACE ( 'NONE', ( #35296 ), #97514, .T. ) ; +#27027 = AXIS2_PLACEMENT_3D ( 'NONE', #46659, #62525, #70655 ) ; +#27028 = VECTOR ( 'NONE', #78109, 1000.000000000000000 ) ; +#27029 = PRESENTATION_STYLE_ASSIGNMENT (( #4023 ) ) ; +#27030 = LINE ( 'NONE', #63816, #64669 ) ; +#27031 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#27032 = SURFACE_STYLE_USAGE ( .BOTH. , #10578 ) ; +#27033 = ADVANCED_FACE ( 'NONE', ( #60281 ), #61281, .T. ) ; +#27034 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#27035 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27036 = LINE ( 'NONE', #36197, #40499 ) ; +#27037 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44470, 'distance_accuracy_value', 'NONE'); +#27038 = VERTEX_POINT ( 'NONE', #68381 ) ; +#27039 = CARTESIAN_POINT ( 'NONE', ( 1.540061115671039982, -0.9808836469697840288, 0.8100000000000000533 ) ) ; +#27040 = ORIENTED_EDGE ( 'NONE', *, *, #53580, .F. ) ; +#27041 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27042 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27043 = LINE ( 'NONE', #26535, #92027 ) ; +#27044 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.1000000000000000056, -11.91999999999999993 ) ) ; +#27045 = SURFACE_STYLE_FILL_AREA ( #18842 ) ; +#27046 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67737 ) ) ; +#27047 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#27048 = EDGE_CURVE ( 'NONE', #7870, #5584, #43914, .T. ) ; +#27049 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8648700000000000276 ) ) ; +#27050 = VECTOR ( 'NONE', #80236, 1000.000000000000000 ) ; +#27051 = ORIENTED_EDGE ( 'NONE', *, *, #41998, .F. ) ; +#27052 = EDGE_LOOP ( 'NONE', ( #52449, #1072, #55433, #69378 ) ) ; +#27053 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.000000000000000000 ) ) ; +#27054 = FILL_AREA_STYLE_COLOUR ( '', #58082 ) ; +#27055 = LINE ( 'NONE', #74004, #7202 ) ; +#27056 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#27057 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#27058 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12109, 'distance_accuracy_value', 'NONE'); +#27059 = STYLED_ITEM ( 'NONE', ( #90125 ), #83640 ) ; +#27060 = DIRECTION ( 'NONE', ( -0.3444045651374283978, 0.000000000000000000, -0.9388213331153583141 ) ) ; +#27061 = STYLED_ITEM ( 'NONE', ( #78713 ), #54391 ) ; +#27062 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27063 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#27064 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.8500000000000000888, 0.5799137866959191978 ) ) ; +#27065 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84105 ), #28708 ) ; +#27066 = FILL_AREA_STYLE_COLOUR ( '', #96690 ) ; +#27067 = ORIENTED_EDGE ( 'NONE', *, *, #93764, .F. ) ; +#27068 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27069 = ADVANCED_FACE ( 'NONE', ( #21433 ), #6051, .T. ) ; +#27070 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4232 ), #56463 ) ; +#27071 = VERTEX_POINT ( 'NONE', #37288 ) ; +#27072 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25403 ), #17258 ) ; +#27073 = STYLED_ITEM ( 'NONE', ( #78163 ), #48795 ) ; +#27074 = LINE ( 'NONE', #89338, #26218 ) ; +#27075 = PRESENTATION_STYLE_ASSIGNMENT (( #4065 ) ) ; +#27076 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27077 = DIRECTION ( 'NONE', ( -0.8942439631056320337, -0.4475798637663818691, 0.000000000000000000 ) ) ; +#27078 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#27079 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000018430, 0.4999999999999997780, 0.8648700000000000276 ) ) ; +#27080 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48295 ), #61333 ) ; +#27081 = LINE ( 'NONE', #57740, #48074 ) ; +#27083 = ORIENTED_EDGE ( 'NONE', *, *, #22477, .T. ) ; +#27082 = ORIENTED_EDGE ( 'NONE', *, *, #27667, .F. ) ; +#27084 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72762 ) ) ; +#27085 = SURFACE_STYLE_USAGE ( .BOTH. , #88845 ) ; +#27086 = EDGE_LOOP ( 'NONE', ( #75291, #11785, #70516, #50460, #85691, #57415, #7019, #35805, #69616, #92101, #7525, #5158 ) ) ; +#27087 = LINE ( 'NONE', #42885, #44167 ) ; +#27088 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75957 ), #7435 ) ; +#27089 = STYLED_ITEM ( 'NONE', ( #74137 ), #22765 ) ; +#27091 = FILL_AREA_STYLE_COLOUR ( '', #44692 ) ; +#27090 = FACE_OUTER_BOUND ( 'NONE', #61318, .T. ) ; +#27092 = ORIENTED_EDGE ( 'NONE', *, *, #23263, .T. ) ; +#27093 = EDGE_LOOP ( 'NONE', ( #86719, #27991, #58537, #17468 ) ) ; +#27094 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85723 ), #80880 ) ; +#27095 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 9.417844000000002325, 0.8648700000000000276 ) ) ; +#27096 = CIRCLE ( 'NONE', #46575, 0.01000000000000002623 ) ; +#27097 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27098 = LINE ( 'NONE', #96485, #20507 ) ; +#27099 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27100 = ORIENTED_EDGE ( 'NONE', *, *, #7612, .F. ) ; +#27101 = ORIENTED_EDGE ( 'NONE', *, *, #10239, .T. ) ; +#27102 = PLANE ( 'NONE', #20892 ) ; +#27103 = ORIENTED_EDGE ( 'NONE', *, *, #55866, .F. ) ; +#27104 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#27105 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27106 = EDGE_CURVE ( 'NONE', #33242, #78767, #37044, .T. ) ; +#27107 = STYLED_ITEM ( 'NONE', ( #97372 ), #3861 ) ; +#27109 = ORIENTED_EDGE ( 'NONE', *, *, #17359, .T. ) ; +#27108 = SURFACE_STYLE_FILL_AREA ( #58268 ) ; +#27110 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27111 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27112 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#27113 = VERTEX_POINT ( 'NONE', #76553 ) ; +#27114 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#27115 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#27116 = VERTEX_POINT ( 'NONE', #22964 ) ; +#27117 = ORIENTED_EDGE ( 'NONE', *, *, #5315, .T. ) ; +#27118 = CARTESIAN_POINT ( 'NONE', ( 8.687142999999998949, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#27119 = SURFACE_SIDE_STYLE ('',( #65908 ) ) ; +#27120 = FILL_AREA_STYLE_COLOUR ( '', #10952 ) ; +#27121 = CARTESIAN_POINT ( 'NONE', ( -0.9900897613018839749, -1.321802795360440319, 0.8300000000000000711 ) ) ; +#27122 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12289 ) ) ; +#27123 = SURFACE_SIDE_STYLE ('',( #26616 ) ) ; +#27124 = SURFACE_STYLE_FILL_AREA ( #12197 ) ; +#27126 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27125 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27127 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#27128 = ORIENTED_EDGE ( 'NONE', *, *, #70133, .T. ) ; +#27129 = ORIENTED_EDGE ( 'NONE', *, *, #39615, .F. ) ; +#27130 = SURFACE_STYLE_USAGE ( .BOTH. , #18930 ) ; +#27131 = FILL_AREA_STYLE ('',( #19446 ) ) ; +#27132 = LINE ( 'NONE', #81764, #12361 ) ; +#27133 = CARTESIAN_POINT ( 'NONE', ( -0.4015417829630419932, -1.199500944507529976, 0.8300000000000000711 ) ) ; +#27134 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91031, #62813, #13865 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27135 = FILL_AREA_STYLE ('',( #96526 ) ) ; +#27137 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#27136 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999734, 0.6599999999999998090, -0.9757359312880714564 ) ) ; +#27138 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#27139 = CARTESIAN_POINT ( 'NONE', ( 1.790988317735370039, -1.106837409965790053, 0.8299999999999999600 ) ) ; +#27141 = ADVANCED_FACE ( 'NONE', ( #94382 ), #46910, .T. ) ; +#27140 = SURFACE_STYLE_USAGE ( .BOTH. , #80256 ) ; +#27142 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23852 ) ) ; +#27143 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43363 ) ) ; +#27144 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#27145 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#27146 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44107 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15620, #8406, #14101 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27147 = AXIS2_PLACEMENT_3D ( 'NONE', #11635, #44350, #75038 ) ; +#27148 = FILL_AREA_STYLE_COLOUR ( '', #62922 ) ; +#27149 = ORIENTED_EDGE ( 'NONE', *, *, #29532, .T. ) ; +#27150 = FILL_AREA_STYLE ('',( #74607 ) ) ; +#27151 = SURFACE_STYLE_FILL_AREA ( #11211 ) ; +#27152 = PRESENTATION_STYLE_ASSIGNMENT (( #9710 ) ) ; +#27153 = VECTOR ( 'NONE', #75963, 999.9999999999998863 ) ; +#27154 = ADVANCED_FACE ( 'NONE', ( #63297 ), #86748, .T. ) ; +#27155 = FACE_OUTER_BOUND ( 'NONE', #76242, .T. ) ; +#27156 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77634 ) ) ; +#27158 = EDGE_CURVE ( 'NONE', #53678, #35165, #69891, .T. ) ; +#27157 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94644, 'distance_accuracy_value', 'NONE'); +#27159 = VERTEX_POINT ( 'NONE', #23987 ) ; +#27160 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27161 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#27162 = SURFACE_STYLE_FILL_AREA ( #26654 ) ; +#27164 = AXIS2_PLACEMENT_3D ( 'NONE', #54483, #2747, #39644 ) ; +#27163 = CARTESIAN_POINT ( 'NONE', ( -1.089702767725039934, -0.9656714926165439472, 0.8299999999999999600 ) ) ; +#27165 = LINE ( 'NONE', #51141, #26576 ) ; +#27166 = VECTOR ( 'NONE', #39579, 1000.000000000000114 ) ; +#27167 = LINE ( 'NONE', #3653, #48627 ) ; +#27168 = SURFACE_SIDE_STYLE ('',( #40976 ) ) ; +#27169 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#27170 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27171 = EDGE_CURVE ( 'NONE', #26081, #64141, #456, .T. ) ; +#27172 = ADVANCED_FACE ( 'NONE', ( #69367 ), #31612, .F. ) ; +#27173 = PRESENTATION_STYLE_ASSIGNMENT (( #66948 ) ) ; +#27174 = ORIENTED_EDGE ( 'NONE', *, *, #90923, .T. ) ; +#27175 = VERTEX_POINT ( 'NONE', #10047 ) ; +#27176 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27177 = LINE ( 'NONE', #25654, #43748 ) ; +#27178 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85948, 'distance_accuracy_value', 'NONE'); +#27179 = ADVANCED_FACE ( 'NONE', ( #65790 ), #2992, .T. ) ; +#27180 = EDGE_CURVE ( 'NONE', #1613, #62506, #49987, .T. ) ; +#27181 = SURFACE_STYLE_FILL_AREA ( #79789 ) ; +#27182 = LINE ( 'NONE', #82300, #5574 ) ; +#27183 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27184 = SURFACE_STYLE_FILL_AREA ( #57321 ) ; +#27185 = STYLED_ITEM ( 'NONE', ( #17498 ), #13317 ) ; +#27186 = SURFACE_SIDE_STYLE ('',( #88436 ) ) ; +#27187 = PLANE ( 'NONE', #66489 ) ; +#27188 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#27189 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#27190 = ORIENTED_EDGE ( 'NONE', *, *, #37617, .F. ) ; +#27191 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.500000000000000000, 0.1829999999999580296 ) ) ; +#27192 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27193 = LINE ( 'NONE', #49664, #65596 ) ; +#27194 = VERTEX_POINT ( 'NONE', #96387 ) ; +#27195 = ADVANCED_FACE ( 'NONE', ( #26489 ), #19820, .T. ) ; +#27196 = ORIENTED_EDGE ( 'NONE', *, *, #65354, .F. ) ; +#27197 = AXIS2_PLACEMENT_3D ( 'NONE', #47569, #79221, #55754 ) ; +#27198 = EDGE_CURVE ( 'NONE', #77162, #7996, #29959, .T. ) ; +#27199 = STYLED_ITEM ( 'NONE', ( #57801 ), #30444 ) ; +#27200 = PRESENTATION_STYLE_ASSIGNMENT (( #97088 ) ) ; +#27201 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#27202 = ORIENTED_EDGE ( 'NONE', *, *, #2488, .T. ) ; +#27203 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#27204 = ORIENTED_EDGE ( 'NONE', *, *, #18447, .F. ) ; +#27205 = FACE_OUTER_BOUND ( 'NONE', #37235, .T. ) ; +#27206 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27207 = AXIS2_PLACEMENT_3D ( 'NONE', #37432, #59434, #52255 ) ; +#27208 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#27209 = VERTEX_POINT ( 'NONE', #83621 ) ; +#27210 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18239 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3535, #81660, #64798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27211 = ORIENTED_EDGE ( 'NONE', *, *, #44203, .T. ) ; +#27212 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98293 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71160, #56885, #40546 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27213 = FACE_OUTER_BOUND ( 'NONE', #49241, .T. ) ; +#27214 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27215 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#27216 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27217 = VECTOR ( 'NONE', #28354, 1000.000000000000000 ) ; +#27219 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27218 = PRESENTATION_STYLE_ASSIGNMENT (( #94212 ) ) ; +#27220 = ORIENTED_EDGE ( 'NONE', *, *, #97444, .T. ) ; +#27222 = EDGE_LOOP ( 'NONE', ( #57210, #70888, #94697, #64407, #30210, #20069 ) ) ; +#27221 = ORIENTED_EDGE ( 'NONE', *, *, #17631, .T. ) ; +#27223 = VERTEX_POINT ( 'NONE', #44278 ) ; +#27224 = SURFACE_STYLE_USAGE ( .BOTH. , #42028 ) ; +#27225 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27226 = ADVANCED_FACE ( 'NONE', ( #52477 ), #59169, .T. ) ; +#27227 = ORIENTED_EDGE ( 'NONE', *, *, #42, .T. ) ; +#27228 = ORIENTED_EDGE ( 'NONE', *, *, #5697, .F. ) ; +#27229 = VECTOR ( 'NONE', #53016, 1000.000000000000000 ) ; +#27230 = FILL_AREA_STYLE_COLOUR ( '', #18171 ) ; +#27231 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27232 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8648700000000000276 ) ) ; +#27233 = ORIENTED_EDGE ( 'NONE', *, *, #30229, .T. ) ; +#27235 = EDGE_CURVE ( 'NONE', #80733, #100104, #95716, .T. ) ; +#27234 = LINE ( 'NONE', #43020, #34268 ) ; +#27236 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #2490, #33651, #95886, #57657 ), + ( #86745, #70923, #63294, #94380 ), + ( #41803, #16759, #47942, #36163 ), + ( #51982, #67270, #13075, #74456 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#27237 = VERTEX_POINT ( 'NONE', #45267 ) ; +#27238 = STYLED_ITEM ( 'NONE', ( #36682 ), #39651 ) ; +#27239 = CARTESIAN_POINT ( 'NONE', ( 0.3278745635850867091, -1.323480467039047870, 0.8100000000000000533 ) ) ; +#27240 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#27241 = CARTESIAN_POINT ( 'NONE', ( 7.386065916749879889, 4.849934916749958802, 0.8648700000000000276 ) ) ; +#27242 = CARTESIAN_POINT ( 'NONE', ( 0.5010457827341869841, -1.198290873665909917, 0.8299999999999999600 ) ) ; +#27243 = FILL_AREA_STYLE_COLOUR ( '', #82846 ) ; +#27244 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27245 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000013323, 0.1829999999999659954 ) ) ; +#27246 = CARTESIAN_POINT ( 'NONE', ( 1.731329805614240325, -1.441250752426249893, 0.8299999999999999600 ) ) ; +#27248 = FILL_AREA_STYLE_COLOUR ( '', #41670 ) ; +#27247 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1833333333333333481, 0.000000000000000000 ) ) ; +#27249 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27250 = EDGE_CURVE ( 'NONE', #87865, #60625, #84108, .T. ) ; +#27251 = ORIENTED_EDGE ( 'NONE', *, *, #75779, .T. ) ; +#27252 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999942962, -1.979898987322330051, 0.6999285677838846809 ) ) ; +#27253 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14127 ), #69611 ) ; +#27254 = CARTESIAN_POINT ( 'NONE', ( 1.441086107696939900, -1.316410597191429943, 0.8300000000000022915 ) ) ; +#27255 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#27256 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#27257 = LINE ( 'NONE', #58420, #15695 ) ; +#27258 = EDGE_CURVE ( 'NONE', #41260, #78062, #20817, .T. ) ; +#27259 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#27260 = PLANE ( 'NONE', #2018 ) ; +#27261 = CARTESIAN_POINT ( 'NONE', ( 1.080509293578989949, -0.9076590548536891401, 0.8100000000000000533 ) ) ; +#27262 = VERTEX_POINT ( 'NONE', #22315 ) ; +#27263 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27264 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27265 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8648700000000000276 ) ) ; +#27266 = VERTEX_POINT ( 'NONE', #13077 ) ; +#27267 = VECTOR ( 'NONE', #89776, 1000.000000000000000 ) ; +#27268 = PLANE ( 'NONE', #7874 ) ; +#27269 = FACE_OUTER_BOUND ( 'NONE', #94235, .T. ) ; +#27270 = CARTESIAN_POINT ( 'NONE', ( 1.575220826706200228, -1.366783821657739928, 0.8099999999999976108 ) ) ; +#27271 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 1.000357204479958347E-16, 0.8499999999999999778 ) ) ; +#27272 = FACE_OUTER_BOUND ( 'NONE', #96122, .T. ) ; +#27273 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27274 = ORIENTED_EDGE ( 'NONE', *, *, #69906, .T. ) ; +#27275 = SURFACE_STYLE_USAGE ( .BOTH. , #97656 ) ; +#27276 = SURFACE_SIDE_STYLE ('',( #3276 ) ) ; +#27277 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#27278 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#27279 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27280 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.35000000000000142, 0.000000000000000000 ) ) ; +#27281 = AXIS2_PLACEMENT_3D ( 'NONE', #86884, #62915, #33272 ) ; +#27282 = PRESENTATION_STYLE_ASSIGNMENT (( #97179 ) ) ; +#27283 = PRESENTATION_STYLE_ASSIGNMENT (( #33948 ) ) ; +#27284 = LINE ( 'NONE', #87044, #32889 ) ; +#27285 = VECTOR ( 'NONE', #85057, 1000.000000000000000 ) ; +#27286 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000021, 0.2350000000000000144 ) ) ; +#27287 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27288 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56092 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58815, #6585, #90927 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27289 = VERTEX_POINT ( 'NONE', #91261 ) ; +#27290 = ORIENTED_EDGE ( 'NONE', *, *, #6790, .T. ) ; +#27291 = EDGE_CURVE ( 'NONE', #54719, #56847, #44771, .T. ) ; +#27293 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12546 ), #4446 ) ; +#27292 = FILL_AREA_STYLE_COLOUR ( '', #11749 ) ; +#27294 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#27295 = AXIS2_PLACEMENT_3D ( 'NONE', #3571, #26061, #66352 ) ; +#27296 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.500000000000000444, 0.000000000000000000 ) ) ; +#27297 = DIRECTION ( 'NONE', ( -6.123233995736766036E-17, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27298 = CLOSED_SHELL ( 'NONE', ( #88964, #22884, #42202, #66387, #50444, #62787 ) ) ; +#27299 = ORIENTED_EDGE ( 'NONE', *, *, #48637, .T. ) ; +#27300 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27301 = SURFACE_STYLE_USAGE ( .BOTH. , #97206 ) ; +#27302 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53370 ) ) ; +#27303 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95759 ) ) ; +#27304 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 1.306104834246980087E-31 ) ) ; +#27305 = EDGE_CURVE ( 'NONE', #28951, #32855, #5444, .T. ) ; +#27306 = LINE ( 'NONE', #50316, #89527 ) ; +#27307 = ORIENTED_EDGE ( 'NONE', *, *, #18104, .T. ) ; +#27308 = FILL_AREA_STYLE_COLOUR ( '', #65706 ) ; +#27309 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71308 ) ) ; +#27310 = SURFACE_SIDE_STYLE ('',( #42126 ) ) ; +#27311 = ADVANCED_FACE ( 'NONE', ( #75944 ), #82127, .T. ) ; +#27312 = VECTOR ( 'NONE', #63892, 1000.000000000000000 ) ; +#27313 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27314 = SURFACE_SIDE_STYLE ('',( #11876 ) ) ; +#27315 = CARTESIAN_POINT ( 'NONE', ( -1.175156004799000176, -1.443574297695930264, 0.8299999999999999600 ) ) ; +#27316 = VERTEX_POINT ( 'NONE', #46791 ) ; +#27317 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#27318 = SURFACE_STYLE_USAGE ( .BOTH. , #97221 ) ; +#27319 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8648700000000000276 ) ) ; +#27320 = ORIENTED_EDGE ( 'NONE', *, *, #52957, .T. ) ; +#27321 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#27322 = FILL_AREA_STYLE_COLOUR ( '', #6410 ) ; +#27323 = SURFACE_SIDE_STYLE ('',( #43127 ) ) ; +#27324 = VECTOR ( 'NONE', #22214, 1000.000000000000000 ) ; +#27325 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27326 = ORIENTED_EDGE ( 'NONE', *, *, #57745, .F. ) ; +#27327 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#27328 = VECTOR ( 'NONE', #87151, 1000.000000000000114 ) ; +#27329 = VERTEX_POINT ( 'NONE', #76954 ) ; +#27330 = ORIENTED_EDGE ( 'NONE', *, *, #77738, .T. ) ; +#27331 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88874, 'distance_accuracy_value', 'NONE'); +#27332 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27334 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27333 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27335 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.500000000000000000, 0.000000000000000000 ) ) ; +#27336 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01499999999999998557, 0.1400000000000000133 ) ) ; +#27337 = EDGE_CURVE ( 'NONE', #27981, #51456, #1359, .T. ) ; +#27338 = FILL_AREA_STYLE ('',( #91116 ) ) ; +#27339 = SURFACE_STYLE_FILL_AREA ( #89616 ) ; +#27340 = ORIENTED_EDGE ( 'NONE', *, *, #46759, .T. ) ; +#27341 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27342 = CARTESIAN_POINT ( 'NONE', ( 1.395857244856030022, -1.450479623942970253, 0.8100000000000000533 ) ) ; +#27343 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#27344 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27345 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27346 = ORIENTED_EDGE ( 'NONE', *, *, #95677, .T. ) ; +#27347 = VERTEX_POINT ( 'NONE', #337 ) ; +#27348 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46843 ), #76225 ) ; +#27349 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#27350 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27351 = VECTOR ( 'NONE', #99118, 1000.000000000000000 ) ; +#27352 = AXIS2_PLACEMENT_3D ( 'NONE', #84145, #20853, #91786 ) ; +#27353 = ORIENTED_EDGE ( 'NONE', *, *, #86451, .T. ) ; +#27354 = FILL_AREA_STYLE_COLOUR ( '', #46698 ) ; +#27355 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21112, #10857, #100103 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27356 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100595 ), #6064 ) ; +#27357 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#27358 = ORIENTED_EDGE ( 'NONE', *, *, #87214, .F. ) ; +#27360 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95747 ) ) ; +#27359 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27361 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#27362 = ORIENTED_EDGE ( 'NONE', *, *, #58779, .T. ) ; +#27363 = LINE ( 'NONE', #66639, #19256 ) ; +#27364 = CLOSED_SHELL ( 'NONE', ( #91480, #94544, #31965, #65840, #55761, #78264 ) ) ; +#27365 = CARTESIAN_POINT ( 'NONE', ( -0.9931616945682509856, -1.308270162923429902, 0.8299999999999999600 ) ) ; +#27366 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22626 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58812, #60312, #66925 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27367 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8648700000000000276 ) ) ; +#27368 = VECTOR ( 'NONE', #58347, 1000.000000000000000 ) ; +#27369 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#27370 = LINE ( 'NONE', #58547, #68611 ) ; +#27371 = SURFACE_STYLE_USAGE ( .BOTH. , #82006 ) ; +#27372 = SURFACE_STYLE_USAGE ( .BOTH. , #4860 ) ; +#27373 = ORIENTED_EDGE ( 'NONE', *, *, #2701, .T. ) ; +#27374 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#27375 = AXIS2_PLACEMENT_3D ( 'NONE', #47554, #10158, #25121 ) ; +#27377 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.850000000000000089, 0.000000000000000000 ) ) ; +#27376 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27378 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59354, 'distance_accuracy_value', 'NONE'); +#27379 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27380 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30609 ) ) ; +#27381 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#27382 = PRESENTATION_STYLE_ASSIGNMENT (( #26890 ) ) ; +#27383 = CARTESIAN_POINT ( 'NONE', ( 4.281867249749913285, 4.984284750250088436, 0.8648700000000000276 ) ) ; +#27384 = EDGE_CURVE ( 'NONE', #50972, #13302, #49468, .T. ) ; +#27385 = ORIENTED_EDGE ( 'NONE', *, *, #17912, .F. ) ; +#27386 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#27387 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27388 = SURFACE_STYLE_USAGE ( .BOTH. , #19718 ) ; +#27389 = SURFACE_STYLE_FILL_AREA ( #2906 ) ; +#27390 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27391 = AXIS2_PLACEMENT_3D ( 'NONE', #84308, #55211, #47004 ) ; +#27392 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27393 = CARTESIAN_POINT ( 'NONE', ( -0.8110130133853420409, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#27394 = FILL_AREA_STYLE_COLOUR ( '', #99457 ) ; +#27395 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27396 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27397 = FILL_AREA_STYLE_COLOUR ( '', #13201 ) ; +#27398 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27399 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27400 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27402 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27404 = EDGE_CURVE ( 'NONE', #454, #22600, #69232, .T. ) ; +#27403 = SURFACE_SIDE_STYLE ('',( #96307 ) ) ; +#27405 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27406 = STYLED_ITEM ( 'NONE', ( #68688 ), #84532 ) ; +#27407 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20907 ) ) ; +#27408 = LINE ( 'NONE', #13500, #73940 ) ; +#27409 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27410 = FACE_OUTER_BOUND ( 'NONE', #53979, .T. ) ; +#27411 = FILL_AREA_STYLE ('',( #10456 ) ) ; +#27412 = ORIENTED_EDGE ( 'NONE', *, *, #91463, .T. ) ; +#27414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60134 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57704, #18324, #88805 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27413 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.000000000000000000 ) ) ; +#27415 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980549, 0.000000000000000000 ) ) ; +#27416 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27417 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#27418 = EDGE_CURVE ( 'NONE', #18355, #85080, #6911, .T. ) ; +#27419 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94319 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65630, #81499, #42172 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27420 = FILL_AREA_STYLE ('',( #57587 ) ) ; +#27421 = FILL_AREA_STYLE_COLOUR ( '', #27244 ) ; +#27423 = VERTEX_POINT ( 'NONE', #16141 ) ; +#27422 = AXIS2_PLACEMENT_3D ( 'NONE', #22608, #30746, #53747 ) ; +#27424 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.5000000000000000000, -12.44500000000000028 ) ) ; +#27425 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#27426 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27427 = VECTOR ( 'NONE', #2670, 1000.000000000000000 ) ; +#27428 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27429 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27430 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73055 ), #51853 ) ; +#27431 = CLOSED_SHELL ( 'NONE', ( #87543, #49444, #54011, #34467, #98387, #48969 ) ) ; +#27432 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44766, #59162, #96885, #4958 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27433 = PLANE ( 'NONE', #99036 ) ; +#27434 = ORIENTED_EDGE ( 'NONE', *, *, #29124, .F. ) ; +#27435 = VERTEX_POINT ( 'NONE', #55515 ) ; +#27436 = AXIS2_PLACEMENT_3D ( 'NONE', #50058, #66350, #5026 ) ; +#27437 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#27438 = PLANE ( 'NONE', #86583 ) ; +#27439 = ORIENTED_EDGE ( 'NONE', *, *, #78880, .F. ) ; +#27440 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27441 = AXIS2_PLACEMENT_3D ( 'NONE', #60297, #76076, #14237 ) ; +#27442 = FILL_AREA_STYLE_COLOUR ( '', #27110 ) ; +#27443 = SURFACE_STYLE_FILL_AREA ( #91703 ) ; +#27444 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#27445 = AXIS2_PLACEMENT_3D ( 'NONE', #12624, #80655, #51540 ) ; +#27446 = SURFACE_STYLE_USAGE ( .BOTH. , #81590 ) ; +#27447 = EDGE_CURVE ( 'NONE', #11614, #5281, #82385, .T. ) ; +#27448 = SURFACE_SIDE_STYLE ('',( #12536 ) ) ; +#27449 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27451 = VERTEX_POINT ( 'NONE', #7919 ) ; +#27450 = ORIENTED_EDGE ( 'NONE', *, *, #73978, .T. ) ; +#27452 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #57968, #29294 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #53934 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#27453 = ORIENTED_EDGE ( 'NONE', *, *, #74560, .F. ) ; +#27454 = VECTOR ( 'NONE', #23137, 1000.000000000000000 ) ; +#27455 = VERTEX_POINT ( 'NONE', #100309 ) ; +#27456 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#27457 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10061, 'distance_accuracy_value', 'NONE'); +#27458 = FILL_AREA_STYLE ('',( #97354 ) ) ; +#27460 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2850000000000000311, -0.1458578643762690197 ) ) ; +#27459 = LINE ( 'NONE', #89725, #76943 ) ; +#27461 = ORIENTED_EDGE ( 'NONE', *, *, #92495, .T. ) ; +#27462 = ADVANCED_FACE ( 'NONE', ( #23854 ), #93235, .T. ) ; +#27463 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27464 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27465 = FACE_OUTER_BOUND ( 'NONE', #80628, .T. ) ; +#27466 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87173 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76022, #19387, #66365 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27467 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, 0.000000000000000000 ) ) ; +#27469 = EDGE_LOOP ( 'NONE', ( #82085, #10713, #71049, #76173 ) ) ; +#27468 = VECTOR ( 'NONE', #96489, 1000.000000000000000 ) ; +#27471 = FILL_AREA_STYLE ('',( #49963 ) ) ; +#27470 = FACE_OUTER_BOUND ( 'NONE', #44381, .T. ) ; +#27472 = EDGE_LOOP ( 'NONE', ( #5382, #15326, #96408, #67824 ) ) ; +#27473 = VERTEX_POINT ( 'NONE', #54497 ) ; +#27474 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662329837, -1.437662337662340084, 0.8299999999999999600 ) ) ; +#27475 = VECTOR ( 'NONE', #96665, 1000.000000000000000 ) ; +#27476 = PLANE ( 'NONE', #88596 ) ; +#27477 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#27478 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#27479 = ORIENTED_EDGE ( 'NONE', *, *, #46667, .T. ) ; +#27480 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24208 ) ) ; +#27481 = SURFACE_SIDE_STYLE ('',( #4468 ) ) ; +#27482 = VERTEX_POINT ( 'NONE', #22838 ) ; +#27483 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69858 ) ) ; +#27484 = VECTOR ( 'NONE', #72466, 1000.000000000000000 ) ; +#27485 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#27486 = FILL_AREA_STYLE_COLOUR ( '', #45701 ) ; +#27487 = ORIENTED_EDGE ( 'NONE', *, *, #207, .T. ) ; +#27488 = SURFACE_STYLE_FILL_AREA ( #19815 ) ; +#27489 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8099999999999808464 ) ) ; +#27490 = ORIENTED_EDGE ( 'NONE', *, *, #17721, .T. ) ; +#27491 = ORIENTED_EDGE ( 'NONE', *, *, #81, .T. ) ; +#27493 = SURFACE_SIDE_STYLE ('',( #97863 ) ) ; +#27492 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27494 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46990 ), #76362 ) ; +#27495 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#27496 = SURFACE_STYLE_USAGE ( .BOTH. , #34661 ) ; +#27497 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62470 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87888, #75584, #67889 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27498 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27499 = FILL_AREA_STYLE_COLOUR ( '', #55682 ) ; +#27500 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#27501 = ADVANCED_FACE ( 'NONE', ( #85606 ), #47822, .T. ) ; +#27502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27503 = SURFACE_SIDE_STYLE ('',( #10550 ) ) ; +#27505 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50343 ) ) ; +#27504 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58317, 'distance_accuracy_value', 'NONE'); +#27506 = ORIENTED_EDGE ( 'NONE', *, *, #75225, .T. ) ; +#27507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56817 ) ) ; +#27508 = AXIS2_PLACEMENT_3D ( 'NONE', #14023, #45182, #76350 ) ; +#27509 = PLANE ( 'NONE', #26840 ) ; +#27510 = ORIENTED_EDGE ( 'NONE', *, *, #37439, .T. ) ; +#27511 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27512 = CARTESIAN_POINT ( 'NONE', ( 1.394831661730270067, -1.224577966852969935, 0.8100000000000000533 ) ) ; +#27513 = VECTOR ( 'NONE', #94808, 1000.000000000000000 ) ; +#27514 = PLANE ( 'NONE', #20266 ) ; +#27515 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#27516 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.19999999999999929, 0.000000000000000000 ) ) ; +#27517 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27518 = EDGE_CURVE ( 'NONE', #10139, #19290, #9925, .T. ) ; +#27519 = ORIENTED_EDGE ( 'NONE', *, *, #94829, .T. ) ; +#27520 = EDGE_CURVE ( 'NONE', #38882, #60423, #33009, .T. ) ; +#27521 = SURFACE_SIDE_STYLE ('',( #11082 ) ) ; +#27523 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 1.748130741908801027E-14 ) ) ; +#27522 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75365, #98765, #5869, #45683 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27524 = CARTESIAN_POINT ( 'NONE', ( 0.2164741715418609935, -0.9593045227066020475, 0.8100000000000000533 ) ) ; +#27525 = SURFACE_STYLE_FILL_AREA ( #80646 ) ; +#27526 = DIRECTION ( 'NONE', ( -0.7071071146859689849, -0.7071064476869689530, 0.000000000000000000 ) ) ; +#27527 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27528 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#27529 = FILL_AREA_STYLE_COLOUR ( '', #64651 ) ; +#27530 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24524, 'distance_accuracy_value', 'NONE'); +#27531 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27532 = VECTOR ( 'NONE', #47690, 1000.000000000000000 ) ; +#27533 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27534 = FACE_OUTER_BOUND ( 'NONE', #97448, .T. ) ; +#27535 = LINE ( 'NONE', #64803, #56940 ) ; +#27536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27537 = ADVANCED_FACE ( 'NONE', ( #34035 ), #10413, .T. ) ; +#27538 = PLANE ( 'NONE', #48664 ) ; +#27539 = ORIENTED_EDGE ( 'NONE', *, *, #48079, .T. ) ; +#27540 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#27541 = CARTESIAN_POINT ( 'NONE', ( 1.654345427547579961, -0.9032194100038879458, 0.8299999999999999600 ) ) ; +#27542 = EDGE_LOOP ( 'NONE', ( #44232, #9421, #42749, #93147 ) ) ; +#27543 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27544 = LINE ( 'NONE', #87287, #2418 ) ; +#27545 = EDGE_CURVE ( 'NONE', #1836, #48055, #2882, .T. ) ; +#27546 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14425 ), #60212 ) ; +#27547 = FACE_OUTER_BOUND ( 'NONE', #53424, .T. ) ; +#27548 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27549 = EDGE_CURVE ( 'NONE', #49661, #97109, #96762, .T. ) ; +#27550 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66652 ) ) ; +#27551 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35722 ) ) ; +#27552 = LINE ( 'NONE', #19868, #49992 ) ; +#27553 = ORIENTED_EDGE ( 'NONE', *, *, #10179, .F. ) ; +#27554 = EDGE_CURVE ( 'NONE', #22475, #38581, #66156, .T. ) ; +#27555 = ORIENTED_EDGE ( 'NONE', *, *, #38854, .F. ) ; +#27556 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27557 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16061 ), #63430 ) ; +#27558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27640 ) ) ; +#27559 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76424 ) ) ; +#27560 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#27561 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#27562 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27563 = FILL_AREA_STYLE_COLOUR ( '', #28254 ) ; +#27565 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -11.57000000000000028 ) ) ; +#27564 = VECTOR ( 'NONE', #88074, 1000.000000000000000 ) ; +#27566 = VECTOR ( 'NONE', #57216, 1000.000000000000000 ) ; +#27567 = VERTEX_POINT ( 'NONE', #42192 ) ; +#27568 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#27569 = EDGE_LOOP ( 'NONE', ( #86291, #17551, #86977, #63685 ) ) ; +#27570 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27571 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27572 = LINE ( 'NONE', #13147, #43649 ) ; +#27573 = LINE ( 'NONE', #74022, #35323 ) ; +#27574 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27575 = CARTESIAN_POINT ( 'NONE', ( -1.015038904699709921, -1.047446665233070062, 0.8299999999999999600 ) ) ; +#27576 = CARTESIAN_POINT ( 'NONE', ( -0.3725002807689830053, -1.021003931094770056, 0.8100000000000000533 ) ) ; +#27577 = EDGE_CURVE ( 'NONE', #14361, #35525, #73334, .T. ) ; +#27579 = VECTOR ( 'NONE', #37589, 1000.000000000000000 ) ; +#27578 = CARTESIAN_POINT ( 'NONE', ( -1.282481293671730027, -1.007957212727089935, 0.8100000000000000533 ) ) ; +#27580 = VECTOR ( 'NONE', #73254, 1000.000000000000000 ) ; +#27582 = VERTEX_POINT ( 'NONE', #24881 ) ; +#27581 = ORIENTED_EDGE ( 'NONE', *, *, #62749, .F. ) ; +#27583 = STYLED_ITEM ( 'NONE', ( #24246 ), #1152 ) ; +#27584 = FACE_OUTER_BOUND ( 'NONE', #47397, .T. ) ; +#27585 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11147 ), #30819 ) ; +#27586 = ORIENTED_EDGE ( 'NONE', *, *, #20932, .T. ) ; +#27587 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#27589 = PLANE ( 'NONE', #59418 ) ; +#27588 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#27590 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29238 ), #73287 ) ; +#27591 = EDGE_LOOP ( 'NONE', ( #5415, #54930, #23685, #47616 ) ) ; +#27592 = EDGE_CURVE ( 'NONE', #46129, #24305, #56010, .T. ) ; +#27593 = ORIENTED_EDGE ( 'NONE', *, *, #85210, .T. ) ; +#27594 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.463023860841316052E-78, 1.991364888915569965E-47 ) ) ; +#27595 = SURFACE_SIDE_STYLE ('',( #83213 ) ) ; +#27596 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27598 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#27597 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.299999999999999822, -0.02000000000000280026 ) ) ; +#27599 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.699999999999999734, -0.02000000000000000042 ) ) ; +#27601 = VERTEX_POINT ( 'NONE', #1872 ) ; +#27600 = VECTOR ( 'NONE', #15401, 1000.000000000000000 ) ; +#27602 = EDGE_CURVE ( 'NONE', #9413, #76182, #44540, .T. ) ; +#27603 = VERTEX_POINT ( 'NONE', #27367 ) ; +#27604 = VERTEX_POINT ( 'NONE', #58542 ) ; +#27605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86235 ), #45454 ) ; +#27606 = FACE_OUTER_BOUND ( 'NONE', #94080, .T. ) ; +#27607 = EDGE_CURVE ( 'NONE', #51226, #62500, #75819, .T. ) ; +#27610 = ORIENTED_EDGE ( 'NONE', *, *, #33304, .F. ) ; +#27609 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38953 ), #87927 ) ; +#27608 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#27611 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6892, #69213, #100286, #30429 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27612 = SURFACE_SIDE_STYLE ('',( #4103 ) ) ; +#27613 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#27614 = VERTEX_POINT ( 'NONE', #51860 ) ; +#27615 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27616 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#27617 = ORIENTED_EDGE ( 'NONE', *, *, #89517, .F. ) ; +#27618 = ORIENTED_EDGE ( 'NONE', *, *, #96967, .T. ) ; +#27619 = DIRECTION ( 'NONE', ( -0.3444045651374270656, 0.000000000000000000, -0.9388213331153589802 ) ) ; +#27620 = FILL_AREA_STYLE ('',( #56766 ) ) ; +#27621 = SURFACE_STYLE_USAGE ( .BOTH. , #4115 ) ; +#27622 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12488 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97790, #27929, #60091 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27623 = AXIS2_PLACEMENT_3D ( 'NONE', #40155, #88126, #86596 ) ; +#27624 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000009909, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#27625 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #39321, #85790, #15823, #46988 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27626 = ADVANCED_FACE ( 'NONE', ( #99213 ), #85355, .T. ) ; +#27627 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27628 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#27629 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61876 ), #60357 ) ; +#27631 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#27630 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.000000000000000000 ) ) ; +#27632 = STYLED_ITEM ( 'NONE', ( #2413 ), #31874 ) ; +#27633 = LINE ( 'NONE', #50120, #70221 ) ; +#27634 = VERTEX_POINT ( 'NONE', #11939 ) ; +#27635 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27636 = ORIENTED_EDGE ( 'NONE', *, *, #100508, .T. ) ; +#27637 = FILL_AREA_STYLE ('',( #55260 ) ) ; +#27638 = STYLED_ITEM ( 'NONE', ( #12423 ), #56962 ) ; +#27639 = CARTESIAN_POINT ( 'NONE', ( -0.3050011667720459729, -1.377680218341680085, 0.8100000000000000533 ) ) ; +#27640 = STYLED_ITEM ( 'NONE', ( #81815 ), #84990 ) ; +#27641 = CARTESIAN_POINT ( 'NONE', ( -0.4124892269281669743, -1.212011904613210067, 0.8300000000000000711 ) ) ; +#27644 = SURFACE_SIDE_STYLE ('',( #74597 ) ) ; +#27643 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999734, 0.6892893218813450629, -0.8000000000000000444 ) ) ; +#27642 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42502 ) ) ; +#27645 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.297402597402600000, 0.8299999999999999600 ) ) ; +#27646 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27647 = AXIS2_PLACEMENT_3D ( 'NONE', #60976, #13938, #7744 ) ; +#27648 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27649 = EDGE_CURVE ( 'NONE', #52058, #9730, #43162, .T. ) ; +#27650 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27651 = ADVANCED_FACE ( 'NONE', ( #15388 ), #59039, .F. ) ; +#27652 = PRESENTATION_STYLE_ASSIGNMENT (( #97537 ) ) ; +#27653 = SURFACE_STYLE_FILL_AREA ( #75106 ) ; +#27654 = VECTOR ( 'NONE', #100690, 1000.000000000000000 ) ; +#27655 = LINE ( 'NONE', #13744, #37527 ) ; +#27656 = ORIENTED_EDGE ( 'NONE', *, *, #9148, .T. ) ; +#27657 = AXIS2_PLACEMENT_3D ( 'NONE', #6486, #4532, #51553 ) ; +#27658 = SURFACE_SIDE_STYLE ('',( #68420 ) ) ; +#27659 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27660 = SURFACE_STYLE_USAGE ( .BOTH. , #18954 ) ; +#27661 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30897 ), #96193 ) ; +#27662 = EDGE_CURVE ( 'NONE', #84686, #51932, #20175, .T. ) ; +#27663 = ORIENTED_EDGE ( 'NONE', *, *, #79025, .F. ) ; +#27664 = PLANE ( 'NONE', #83199 ) ; +#27665 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#27666 = LINE ( 'NONE', #58824, #73867 ) ; +#27667 = EDGE_CURVE ( 'NONE', #63924, #5565, #38910, .T. ) ; +#27668 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27669 = SURFACE_STYLE_USAGE ( .BOTH. , #43959 ) ; +#27670 = SURFACE_STYLE_FILL_AREA ( #28157 ) ; +#27671 = VECTOR ( 'NONE', #34815, 1000.000000000000000 ) ; +#27672 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27674 = CARTESIAN_POINT ( 'NONE', ( -1.049664478641080034, -1.428972370004099934, 0.8300000000000001821 ) ) ; +#27675 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99278 ) ) ; +#27676 = EDGE_CURVE ( 'NONE', #41904, #14054, #95513, .T. ) ; +#27677 = LINE ( 'NONE', #81796, #7710 ) ; +#27678 = ORIENTED_EDGE ( 'NONE', *, *, #18477, .T. ) ; +#27679 = EDGE_CURVE ( 'NONE', #60362, #31320, #31241, .T. ) ; +#27680 = ORIENTED_EDGE ( 'NONE', *, *, #43419, .F. ) ; +#27681 = SURFACE_SIDE_STYLE ('',( #95554 ) ) ; +#27682 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16171, 'distance_accuracy_value', 'NONE'); +#27683 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92068, 'distance_accuracy_value', 'NONE'); +#27684 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27685 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999990674, 0.1829999999999790128 ) ) ; +#27686 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.1000000000000000056, -13.35000000000000142 ) ) ; +#27687 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27688 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#27689 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.383333333333323090, 0.000000000000000000 ) ) ; +#27690 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27691 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.000000000000000000 ) ) ; +#27692 = ORIENTED_EDGE ( 'NONE', *, *, #41834, .T. ) ; +#27693 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#27694 = EDGE_LOOP ( 'NONE', ( #99012, #50932, #39739, #8921 ) ) ; +#27695 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#27696 = SURFACE_STYLE_USAGE ( .BOTH. , #64969 ) ; +#27697 = ORIENTED_EDGE ( 'NONE', *, *, #77047, .T. ) ; +#27698 = FILL_AREA_STYLE_COLOUR ( '', #100005 ) ; +#27699 = VECTOR ( 'NONE', #25981, 1000.000000000000000 ) ; +#27700 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#27701 = EDGE_CURVE ( 'NONE', #13168, #23531, #15896, .T. ) ; +#27702 = ORIENTED_EDGE ( 'NONE', *, *, #48949, .T. ) ; +#27703 = AXIS2_PLACEMENT_3D ( 'NONE', #83349, #82348, #58390 ) ; +#27704 = DIRECTION ( 'NONE', ( -0.9200319872051170300, -0.3918432626949240327, 0.000000000000000000 ) ) ; +#27705 = VECTOR ( 'NONE', #83053, 1000.000000000000000 ) ; +#27707 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27706 = VECTOR ( 'NONE', #2680, 1000.000000000000000 ) ; +#27708 = ORIENTED_EDGE ( 'NONE', *, *, #38825, .T. ) ; +#27709 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95533 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70025, #8167, #24109 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27710 = AXIS2_PLACEMENT_3D ( 'NONE', #7833, #23758, #70189 ) ; +#27711 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27712 = ORIENTED_EDGE ( 'NONE', *, *, #23818, .T. ) ; +#27713 = ADVANCED_FACE ( 'NONE', ( #39918 ), #71574, .T. ) ; +#27714 = VERTEX_POINT ( 'NONE', #56784 ) ; +#27715 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#27716 = LINE ( 'NONE', #5164, #64491 ) ; +#27717 = FACE_OUTER_BOUND ( 'NONE', #77912, .T. ) ; +#27718 = CARTESIAN_POINT ( 'NONE', ( -0.4442483664529159881, -1.083526083816420016, 0.8100000000000000533 ) ) ; +#27719 = VECTOR ( 'NONE', #42943, 1000.000000000000000 ) ; +#27720 = LINE ( 'NONE', #51193, #87740 ) ; +#27722 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27721 = CARTESIAN_POINT ( 'NONE', ( 0.2603867800980460001, -1.020295711170670083, 0.8299999999999999600 ) ) ; +#27723 = VERTEX_POINT ( 'NONE', #31744 ) ; +#27724 = EDGE_CURVE ( 'NONE', #5428, #13067, #62860, .T. ) ; +#27726 = EDGE_LOOP ( 'NONE', ( #63428, #89126, #43800, #59271 ) ) ; +#27725 = ORIENTED_EDGE ( 'NONE', *, *, #100828, .T. ) ; +#27727 = VERTEX_POINT ( 'NONE', #94518 ) ; +#27728 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27729 = EDGE_CURVE ( 'NONE', #64866, #33079, #24638, .T. ) ; +#27730 = ORIENTED_EDGE ( 'NONE', *, *, #21783, .F. ) ; +#27731 = STYLED_ITEM ( 'NONE', ( #32635 ), #75681 ) ; +#27733 = ORIENTED_EDGE ( 'NONE', *, *, #26333, .T. ) ; +#27732 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27734 = PRESENTATION_STYLE_ASSIGNMENT (( #58387 ) ) ; +#27735 = FILL_AREA_STYLE_COLOUR ( '', #80826 ) ; +#27736 = PLANE ( 'NONE', #39975 ) ; +#27737 = DIRECTION ( 'NONE', ( -2.168404344971010051E-15, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27738 = VERTEX_POINT ( 'NONE', #70032 ) ; +#27739 = CARTESIAN_POINT ( 'NONE', ( 8.227523124874956295, 9.806752875125043900, 0.8991599999999999593 ) ) ; +#27740 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.300000000000000266, -0.02000000000001260145 ) ) ; +#27741 = PRESENTATION_STYLE_ASSIGNMENT (( #5185 ) ) ; +#27742 = ORIENTED_EDGE ( 'NONE', *, *, #83212, .F. ) ; +#27743 = SURFACE_STYLE_USAGE ( .BOTH. , #74693 ) ; +#27745 = CIRCLE ( 'NONE', #32611, 0.009999999999999998473 ) ; +#27744 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27746 = CARTESIAN_POINT ( 'NONE', ( 0.4793384683631900511, -1.221234985172420018, 0.8299999999999999600 ) ) ; +#27747 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71747 ) ) ; +#27748 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#27749 = EDGE_CURVE ( 'NONE', #79553, #23282, #78225, .T. ) ; +#27751 = EDGE_CURVE ( 'NONE', #80337, #32462, #8171, .T. ) ; +#27750 = VECTOR ( 'NONE', #27161, 1000.000000000000000 ) ; +#27752 = FILL_AREA_STYLE ('',( #52235 ) ) ; +#27754 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27753 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27755 = PLANE ( 'NONE', #73397 ) ; +#27756 = ORIENTED_EDGE ( 'NONE', *, *, #48946, .F. ) ; +#27757 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#27758 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #45605, #21672, #93084, #76795 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 4.389721624091468470E-15, 0.0001118058566321757617 ), + .UNSPECIFIED. ) ; +#27759 = CARTESIAN_POINT ( 'NONE', ( 1.095142431513040027, -1.118172950060400073, 0.8300000000000022915 ) ) ; +#27760 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#27761 = DIRECTION ( 'NONE', ( -1.000000000000000000, -3.880665108489179890E-39, -9.583193921014278315E-65 ) ) ; +#27762 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.383333333333320425, 0.000000000000000000 ) ) ; +#27763 = EDGE_CURVE ( 'NONE', #69765, #62837, #48086, .T. ) ; +#27764 = CIRCLE ( 'NONE', #12931, 0.2000000000000000111 ) ; +#27765 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27766 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#27767 = ORIENTED_EDGE ( 'NONE', *, *, #13652, .T. ) ; +#27768 = EDGE_CURVE ( 'NONE', #47305, #33538, #93981, .T. ) ; +#27769 = SURFACE_SIDE_STYLE ('',( #95642 ) ) ; +#27770 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27771 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86399 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17643, #79981, #25364 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27772 = ORIENTED_EDGE ( 'NONE', *, *, #6073, .F. ) ; +#27773 = AXIS2_PLACEMENT_3D ( 'NONE', #44421, #67414, #13225 ) ; +#27774 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27775 = CARTESIAN_POINT ( 'NONE', ( 1.027124486614659382, 0.8310340759269658761, 0.8299999999999999600 ) ) ; +#27776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24511 ) ) ; +#27777 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27778 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27779 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1679 ), #9740 ) ; +#27780 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27781 = VECTOR ( 'NONE', #51983, 1000.000000000000000 ) ; +#27782 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27783 = ORIENTED_EDGE ( 'NONE', *, *, #12430, .F. ) ; +#27784 = LINE ( 'NONE', #34441, #97764 ) ; +#27785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84808 ) ) ; +#27786 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27787 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#27788 = CARTESIAN_POINT ( 'NONE', ( 1.047921542718980081, -0.9264544496121609463, 0.8299999999999994049 ) ) ; +#27789 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27790 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91385 ), #1529 ) ; +#27791 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#27793 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97183 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6344, #91174, #21222 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27794 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#27795 = FILL_AREA_STYLE_COLOUR ( '', #4499 ) ; +#27796 = LINE ( 'NONE', #82414, #41447 ) ; +#27797 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95143, 'distance_accuracy_value', 'NONE'); +#27798 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, -0.1444665087776849932, 0.8000000000000000444 ) ) ; +#27799 = VECTOR ( 'NONE', #46283, 1000.000000000000000 ) ; +#27800 = SURFACE_SIDE_STYLE ('',( #98627 ) ) ; +#27801 = AXIS2_PLACEMENT_3D ( 'NONE', #37065, #15010, #68162 ) ; +#27802 = VERTEX_POINT ( 'NONE', #79752 ) ; +#27803 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#27804 = EDGE_CURVE ( 'NONE', #36359, #6118, #24115, .T. ) ; +#27805 = ORIENTED_EDGE ( 'NONE', *, *, #5337, .F. ) ; +#27806 = SURFACE_STYLE_USAGE ( .BOTH. , #4775 ) ; +#27808 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2451, 'distance_accuracy_value', 'NONE'); +#27807 = STYLED_ITEM ( 'NONE', ( #28459 ), #68967 ) ; +#27809 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85055, 'distance_accuracy_value', 'NONE'); +#27810 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58793 ), #53865 ) ; +#27811 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#27812 = PRESENTATION_STYLE_ASSIGNMENT (( #60948 ) ) ; +#27813 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27814 = CARTESIAN_POINT ( 'NONE', ( -1.383529069078854645, -1.376865229143305225, 0.8099999999997107292 ) ) ; +#27815 = FILL_AREA_STYLE ('',( #36455 ) ) ; +#27816 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27817 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27819 = EDGE_CURVE ( 'NONE', #58037, #466, #40946, .T. ) ; +#27818 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999689, 0.6600000000000000311, -0.7999999999999999334 ) ) ; +#27820 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8100000000000001643 ) ) ; +#27821 = VERTEX_POINT ( 'NONE', #66908 ) ; +#27822 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27823 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10301, 'distance_accuracy_value', 'NONE'); +#27824 = VECTOR ( 'NONE', #36247, 1000.000000000000114 ) ; +#27825 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14689 ) ) ; +#27826 = EDGE_LOOP ( 'NONE', ( #10355, #94928, #49099, #38746 ) ) ; +#27827 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65191, #26410, #90164 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27828 = LINE ( 'NONE', #51298, #60934 ) ; +#27829 = EDGE_CURVE ( 'NONE', #85096, #85797, #97985, .T. ) ; +#27830 = SURFACE_STYLE_USAGE ( .BOTH. , #57982 ) ; +#27831 = ORIENTED_EDGE ( 'NONE', *, *, #41353, .F. ) ; +#27832 = SURFACE_STYLE_USAGE ( .BOTH. , #4318 ) ; +#27833 = FILL_AREA_STYLE ('',( #21142 ) ) ; +#27834 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70181, 'distance_accuracy_value', 'NONE'); +#27835 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8991599999999999593 ) ) ; +#27836 = PRESENTATION_STYLE_ASSIGNMENT (( #44597 ) ) ; +#27837 = EDGE_CURVE ( 'NONE', #65434, #12661, #42452, .T. ) ; +#27838 = EDGE_LOOP ( 'NONE', ( #11342, #78725, #36759, #29953 ) ) ; +#27839 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27840 = SURFACE_STYLE_USAGE ( .BOTH. , #50821 ) ; +#27841 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#27842 = CARTESIAN_POINT ( 'NONE', ( 1.966666666666663454, -3.500000000000000000, 0.000000000000000000 ) ) ; +#27843 = EDGE_LOOP ( 'NONE', ( #51333, #1796, #65408, #58700 ) ) ; +#27844 = LINE ( 'NONE', #42644, #100234 ) ; +#27845 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #96375, #41302 ), + ( #3982, #79596 ), + ( #34155, #56637 ), + ( #89262, #9547 ), + ( #42304, #57134 ), + ( #10528, #49977 ), + ( #26982, #11051 ), + ( #87744, #88257 ), + ( #48958, #1980 ), + ( #89743, #72932 ), + ( #19292, #80108 ), + ( #33643, #18266 ), + ( #42791, #72405 ), + ( #80609, #2986 ), + ( #40791, #57648 ), + ( #50487, #66279 ), + ( #71933, #65259 ), + ( #26480, #88750 ), + ( #73444, #97377 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07232018030895200067, 0.1403020240650759975, 0.2056949503128689960, 0.2680970257553140224, 0.3283846161759810256, 0.3866606845022029781, 0.4439167269204030153, 0.5001855221813320540, 0.5567435589820139974, 0.6139463218703099523, 0.6733207137601100456, 0.7343865386942719509, 0.7975760200560489954, 0.8623103139506780312, 0.9300018147880010355, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27846 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#27847 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#27848 = VECTOR ( 'NONE', #6343, 1000.000000000000000 ) ; +#27849 = EDGE_CURVE ( 'NONE', #17507, #19915, #50626, .T. ) ; +#27850 = ORIENTED_EDGE ( 'NONE', *, *, #57139, .F. ) ; +#27853 = ORIENTED_EDGE ( 'NONE', *, *, #38583, .T. ) ; +#27852 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, -3.500000000000000444, 0.000000000000000000 ) ) ; +#27851 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65284 ), #21253 ) ; +#27854 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27157 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94644, #16520, #7791 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27855 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#27856 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.5105124837953329830, -0.7500000000000000000 ) ) ; +#27857 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8648700000000000276 ) ) ; +#27858 = AXIS2_PLACEMENT_3D ( 'NONE', #14809, #47006, #16843 ) ; +#27859 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01085786437626904723, 0.1500000000000000222 ) ) ; +#27860 = EDGE_CURVE ( 'NONE', #23167, #97350, #799, .T. ) ; +#27861 = ORIENTED_EDGE ( 'NONE', *, *, #83100, .F. ) ; +#27862 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2403 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78535, #39228, #39745 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27863 = EDGE_LOOP ( 'NONE', ( #223, #64372, #49447, #39652 ) ) ; +#27864 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9815 ) ) ; +#27865 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#27866 = ORIENTED_EDGE ( 'NONE', *, *, #30959, .T. ) ; +#27867 = EDGE_CURVE ( 'NONE', #79988, #702, #81269, .T. ) ; +#27868 = EDGE_CURVE ( 'NONE', #99462, #19702, #57792, .T. ) ; +#27870 = SURFACE_STYLE_FILL_AREA ( #28837 ) ; +#27869 = FILL_AREA_STYLE_COLOUR ( '', #31602 ) ; +#27871 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62045 ) ) ; +#27872 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27873 = STYLED_ITEM ( 'NONE', ( #93001 ), #2079 ) ; +#27874 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#27875 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19397, #50575, #19903, #81715 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27876 = VECTOR ( 'NONE', #29700, 1000.000000000000000 ) ; +#27877 = EDGE_CURVE ( 'NONE', #16986, #50603, #59305, .T. ) ; +#27878 = EDGE_CURVE ( 'NONE', #70495, #27175, #90388, .T. ) ; +#27879 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#27880 = VERTEX_POINT ( 'NONE', #19450 ) ; +#27881 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27882 = ORIENTED_EDGE ( 'NONE', *, *, #49879, .F. ) ; +#27883 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#27884 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27885 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#27886 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #25127, #56261, #79736, #10161 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27887 = EDGE_CURVE ( 'NONE', #61497, #86061, #11570, .T. ) ; +#27888 = AXIS2_PLACEMENT_3D ( 'NONE', #6819, #60077, #5365 ) ; +#27889 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#27890 = CARTESIAN_POINT ( 'NONE', ( 0.3814764115086780039, -1.210722004796850104, 0.8100000000000000533 ) ) ; +#27891 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#27892 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27893 = EDGE_CURVE ( 'NONE', #11603, #37149, #35313, .T. ) ; +#27894 = CARTESIAN_POINT ( 'NONE', ( 1.237877634622789991, -0.9585098101514269997, 0.8100000000000000533 ) ) ; +#27895 = ORIENTED_EDGE ( 'NONE', *, *, #22848, .T. ) ; +#27896 = SURFACE_SIDE_STYLE ('',( #92136 ) ) ; +#27897 = LINE ( 'NONE', #81531, #31761 ) ; +#27900 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27899 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8648700000000000276 ) ) ; +#27898 = LINE ( 'NONE', #59053, #8739 ) ; +#27901 = AXIS2_PLACEMENT_3D ( 'NONE', #28668, #74646, #4671 ) ; +#27902 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27903 = PRESENTATION_STYLE_ASSIGNMENT (( #67166 ) ) ; +#27904 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000019873, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#27905 = FILL_AREA_STYLE_COLOUR ( '', #83636 ) ; +#27906 = ORIENTED_EDGE ( 'NONE', *, *, #43825, .T. ) ; +#27907 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27908 = SURFACE_STYLE_FILL_AREA ( #97772 ) ; +#27909 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#27910 = LINE ( 'NONE', #81546, #88856 ) ; +#27911 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#27912 = AXIS2_PLACEMENT_3D ( 'NONE', #94113, #33400, #87498 ) ; +#27913 = CARTESIAN_POINT ( 'NONE', ( 0.4672226176551799726, -1.085850084742399968, 0.8300000000000015143 ) ) ; +#27914 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27915 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#27916 = FACE_OUTER_BOUND ( 'NONE', #29088, .T. ) ; +#27917 = AXIS2_PLACEMENT_3D ( 'NONE', #23585, #72942, #3510 ) ; +#27918 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49117 ) ) ; +#27919 = FACE_OUTER_BOUND ( 'NONE', #15515, .T. ) ; +#27920 = CARTESIAN_POINT ( 'NONE', ( 6.876949127034753140, 10.29465662703633555, 0.8991599999999999593 ) ) ; +#27921 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#27922 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#27923 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#27924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77239, 'distance_accuracy_value', 'NONE'); +#27925 = VECTOR ( 'NONE', #92984, 1000.000000000000000 ) ; +#27926 = CARTESIAN_POINT ( 'NONE', ( 1.799634867437250207, -1.074567238704529970, 0.8299999999999997380 ) ) ; +#27927 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#27928 = FACE_OUTER_BOUND ( 'NONE', #49039, .T. ) ; +#27930 = EDGE_CURVE ( 'NONE', #80299, #94814, #89890, .T. ) ; +#27929 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#27931 = FILL_AREA_STYLE_COLOUR ( '', #42756 ) ; +#27932 = VERTEX_POINT ( 'NONE', #51119 ) ; +#27933 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86572 ) ) ; +#27934 = LINE ( 'NONE', #59085, #91016 ) ; +#27935 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13357, 'distance_accuracy_value', 'NONE'); +#27936 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41943, 'distance_accuracy_value', 'NONE'); +#27938 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9833333333333340587, 0.000000000000000000 ) ) ; +#27937 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4849999999999999867, 0.2500000000000000000 ) ) ; +#27939 = FILL_AREA_STYLE ('',( #66700 ) ) ; +#27940 = FILL_AREA_STYLE_COLOUR ( '', #3702 ) ; +#27941 = VERTEX_POINT ( 'NONE', #65395 ) ; +#27942 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45801 ), #84962 ) ; +#27943 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#27945 = VERTEX_POINT ( 'NONE', #41443 ) ; +#27944 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29033 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34765, #27099, #89361 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27946 = LINE ( 'NONE', #10998, #5715 ) ; +#27947 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27948 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8789, 'distance_accuracy_value', 'NONE'); +#27949 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#27950 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77841, 'distance_accuracy_value', 'NONE'); +#27951 = LINE ( 'NONE', #64342, #66999 ) ; +#27952 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#27953 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#27954 = EDGE_CURVE ( 'NONE', #39650, #84919, #31645, .T. ) ; +#27955 = EDGE_LOOP ( 'NONE', ( #95388, #4345, #78383, #34117 ) ) ; +#27956 = VERTEX_POINT ( 'NONE', #33786 ) ; +#27957 = FILL_AREA_STYLE ('',( #97814 ) ) ; +#27958 = SURFACE_STYLE_USAGE ( .BOTH. , #74900 ) ; +#27959 = ORIENTED_EDGE ( 'NONE', *, *, #6252, .T. ) ; +#27960 = STYLED_ITEM ( 'NONE', ( #17692 ), #51717 ) ; +#27961 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27962 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50784 ), #58951 ) ; +#27963 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54136 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9644, #64361, #57749 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27964 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, 0.000000000000000000 ) ) ; +#27965 = PLANE ( 'NONE', #68789 ) ; +#27967 = ORIENTED_EDGE ( 'NONE', *, *, #52897, .F. ) ; +#27966 = ORIENTED_EDGE ( 'NONE', *, *, #26615, .F. ) ; +#27968 = VECTOR ( 'NONE', #25818, 999.9999999999998863 ) ; +#27969 = ORIENTED_EDGE ( 'NONE', *, *, #7348, .T. ) ; +#27970 = ORIENTED_EDGE ( 'NONE', *, *, #94510, .F. ) ; +#27971 = FILL_AREA_STYLE ('',( #60614 ) ) ; +#27972 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#27973 = SURFACE_STYLE_USAGE ( .BOTH. , #87720 ) ; +#27975 = CARTESIAN_POINT ( 'NONE', ( 1.263299480776550077, -0.8906029366306310591, 0.8100000000000000533 ) ) ; +#27974 = CARTESIAN_POINT ( 'NONE', ( 0.4157215867521200092, -0.9061895606545929960, 0.8100000000000000533 ) ) ; +#27976 = VERTEX_POINT ( 'NONE', #80755 ) ; +#27977 = PLANE ( 'NONE', #795 ) ; +#27978 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#27979 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44205 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98531, #90967, #36854 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#27980 = CARTESIAN_POINT ( 'NONE', ( -1.371243692415410331, -1.052663393014950044, 0.8100000000000000533 ) ) ; +#27981 = VERTEX_POINT ( 'NONE', #10687 ) ; +#27982 = ORIENTED_EDGE ( 'NONE', *, *, #48014, .F. ) ; +#27983 = EDGE_LOOP ( 'NONE', ( #45123, #44815, #28816, #30185 ) ) ; +#27984 = CARTESIAN_POINT ( 'NONE', ( 1.108771792731459982, -1.202560495203230051, 0.8299999999999999600 ) ) ; +#27985 = AXIS2_PLACEMENT_3D ( 'NONE', #26532, #35210, #4523 ) ; +#27986 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8991599999999999593 ) ) ; +#27987 = CARTESIAN_POINT ( 'NONE', ( 1.901254715655620098, -1.325441991778449902, 0.8300000000000004041 ) ) ; +#27988 = SURFACE_STYLE_FILL_AREA ( #2981 ) ; +#27989 = VECTOR ( 'NONE', #8541, 1000.000000000000114 ) ; +#27991 = ORIENTED_EDGE ( 'NONE', *, *, #26287, .T. ) ; +#27990 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#27992 = CONICAL_SURFACE ( 'NONE', #13232, 0.2299999998740531737, 0.7853981633974482790 ) ; +#27993 = FACE_OUTER_BOUND ( 'NONE', #82820, .T. ) ; +#27994 = EDGE_CURVE ( 'NONE', #25100, #58651, #3129, .T. ) ; +#27995 = VERTEX_POINT ( 'NONE', #36294 ) ; +#27996 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#27997 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81146, #42334, #73479, #65812 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#27998 = ORIENTED_EDGE ( 'NONE', *, *, #32823, .F. ) ; +#28000 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#27999 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28001 = EDGE_LOOP ( 'NONE', ( #54442, #43377, #92689, #29446 ) ) ; +#28002 = VERTEX_POINT ( 'NONE', #91401 ) ; +#28003 = FACE_OUTER_BOUND ( 'NONE', #2695, .T. ) ; +#28004 = AXIS2_PLACEMENT_3D ( 'NONE', #25711, #26723, #49712 ) ; +#28005 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#28006 = PRESENTATION_STYLE_ASSIGNMENT (( #59674 ) ) ; +#28007 = STYLED_ITEM ( 'NONE', ( #61591 ), #20963 ) ; +#28008 = FILL_AREA_STYLE_COLOUR ( '', #62988 ) ; +#28009 = VECTOR ( 'NONE', #53030, 1000.000000000000000 ) ; +#28010 = SURFACE_STYLE_FILL_AREA ( #12585 ) ; +#28011 = LINE ( 'NONE', #35173, #83721 ) ; +#28012 = LINE ( 'NONE', #90265, #88464 ) ; +#28013 = LINE ( 'NONE', #34670, #4806 ) ; +#28014 = EDGE_CURVE ( 'NONE', #54417, #31352, #67405, .T. ) ; +#28015 = ORIENTED_EDGE ( 'NONE', *, *, #77962, .T. ) ; +#28016 = ORIENTED_EDGE ( 'NONE', *, *, #33479, .T. ) ; +#28017 = AXIS2_PLACEMENT_3D ( 'NONE', #51831, #44144, #68617 ) ; +#28018 = CARTESIAN_POINT ( 'NONE', ( -0.02448719543550549951, -1.001398657004090254, 0.8299999999999999600 ) ) ; +#28019 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28020 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28021 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28022 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#28023 = LINE ( 'NONE', #19324, #64664 ) ; +#28024 = EDGE_LOOP ( 'NONE', ( #77241, #86474, #67268, #88745 ) ) ; +#28025 = FACE_OUTER_BOUND ( 'NONE', #79179, .T. ) ; +#28026 = FILL_AREA_STYLE_COLOUR ( '', #55358 ) ; +#28027 = CARTESIAN_POINT ( 'NONE', ( 0.1802163075021840088, -1.026304639009830044, 0.8100000000000000533 ) ) ; +#28028 = PLANE ( 'NONE', #22282 ) ; +#28029 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93181 ) ) ; +#28030 = FILL_AREA_STYLE_COLOUR ( '', #22945 ) ; +#28031 = CARTESIAN_POINT ( 'NONE', ( 1.841098443137489937, -1.205608583660890076, 0.8100000000000000533 ) ) ; +#28032 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28033 = LINE ( 'NONE', #33295, #3971 ) ; +#28034 = FILL_AREA_STYLE_COLOUR ( '', #19021 ) ; +#28035 = FILL_AREA_STYLE_COLOUR ( '', #34358 ) ; +#28036 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.600000000000000089, -13.35000000000000142 ) ) ; +#28038 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81830 ) ) ; +#28037 = FILL_AREA_STYLE_COLOUR ( '', #42070 ) ; +#28039 = CARTESIAN_POINT ( 'NONE', ( 1.333992163213469917, -1.033922635360990050, 0.8299999999999995159 ) ) ; +#28040 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46967, 'distance_accuracy_value', 'NONE'); +#28041 = ORIENTED_EDGE ( 'NONE', *, *, #42770, .F. ) ; +#28042 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#28044 = EDGE_CURVE ( 'NONE', #56862, #66984, #53613, .T. ) ; +#28043 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#28045 = PRESENTATION_STYLE_ASSIGNMENT (( #42355 ) ) ; +#28046 = ORIENTED_EDGE ( 'NONE', *, *, #69181, .T. ) ; +#28047 = FILL_AREA_STYLE_COLOUR ( '', #38339 ) ; +#28048 = FILL_AREA_STYLE_COLOUR ( '', #24134 ) ; +#28049 = LINE ( 'NONE', #55788, #99671 ) ; +#28050 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65544 ), #26433 ) ; +#28051 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#28052 = LINE ( 'NONE', #36207, #24377 ) ; +#28053 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6379 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100191, #22704, #23218 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28054 = VECTOR ( 'NONE', #22476, 1000.000000000000000 ) ; +#28055 = VECTOR ( 'NONE', #13120, 999.9999999999998863 ) ; +#28056 = SURFACE_STYLE_USAGE ( .BOTH. , #52039 ) ; +#28057 = EDGE_LOOP ( 'NONE', ( #26454, #32831, #90112, #55142 ) ) ; +#28058 = ORIENTED_EDGE ( 'NONE', *, *, #83534, .T. ) ; +#28059 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#28060 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000000666, -3.123820061220065281, 0.000000000000000000 ) ) ; +#28061 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #17950, #35352, #19982, #65436 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#28062 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#28063 = PLANE ( 'NONE', #77203 ) ; +#28064 = SURFACE_SIDE_STYLE ('',( #42867 ) ) ; +#28065 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8006, 'distance_accuracy_value', 'NONE'); +#28066 = FILL_AREA_STYLE_COLOUR ( '', #3948 ) ; +#28067 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80288, 'distance_accuracy_value', 'NONE'); +#28068 = SURFACE_STYLE_FILL_AREA ( #52048 ) ; +#28069 = STYLED_ITEM ( 'NONE', ( #16766 ), #7776 ) ; +#28070 = ADVANCED_FACE ( 'NONE', ( #54108 ), #14752, .T. ) ; +#28071 = VERTEX_POINT ( 'NONE', #75579 ) ; +#28072 = SURFACE_STYLE_USAGE ( .BOTH. , #97933 ) ; +#28073 = ORIENTED_EDGE ( 'NONE', *, *, #71237, .F. ) ; +#28074 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28075 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28076 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#28077 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28078 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28079 = SURFACE_SIDE_STYLE ('',( #5537 ) ) ; +#28080 = LINE ( 'NONE', #51580, #1754 ) ; +#28082 = VERTEX_POINT ( 'NONE', #52121 ) ; +#28081 = VERTEX_POINT ( 'NONE', #28610 ) ; +#28083 = STYLED_ITEM ( 'NONE', ( #41048 ), #70091 ) ; +#28084 = ORIENTED_EDGE ( 'NONE', *, *, #28552, .T. ) ; +#28085 = FACE_OUTER_BOUND ( 'NONE', #45349, .T. ) ; +#28086 = ORIENTED_EDGE ( 'NONE', *, *, #53645, .T. ) ; +#28087 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81878 ) ) ; +#28088 = EDGE_CURVE ( 'NONE', #24344, #34143, #13215, .T. ) ; +#28089 = VERTEX_POINT ( 'NONE', #68891 ) ; +#28090 = EDGE_CURVE ( 'NONE', #85574, #93901, #99943, .T. ) ; +#28091 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000001235, -0.1350000000000000089 ) ) ; +#28092 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#28093 = STYLED_ITEM ( 'NONE', ( #95546 ), #52162 ) ; +#28095 = CARTESIAN_POINT ( 'NONE', ( 1.162162005104931950, 1.364349903361174121, 0.8100000000000000533 ) ) ; +#28094 = LINE ( 'NONE', #99426, #20402 ) ; +#28096 = PRESENTATION_STYLE_ASSIGNMENT (( #5061 ) ) ; +#28097 = ORIENTED_EDGE ( 'NONE', *, *, #52456, .F. ) ; +#28098 = VERTEX_POINT ( 'NONE', #61297 ) ; +#28099 = VECTOR ( 'NONE', #85836, 1000.000000000000000 ) ; +#28100 = ORIENTED_EDGE ( 'NONE', *, *, #62220, .T. ) ; +#28101 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#28102 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28103 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10058 ) ) ; +#28105 = ORIENTED_EDGE ( 'NONE', *, *, #81460, .F. ) ; +#28104 = LINE ( 'NONE', #5071, #54350 ) ; +#28106 = EDGE_CURVE ( 'NONE', #60257, #86631, #53114, .T. ) ; +#28107 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28108 = ORIENTED_EDGE ( 'NONE', *, *, #43816, .F. ) ; +#28109 = CARTESIAN_POINT ( 'NONE', ( -0.03797038500300969899, -1.235192314287260062, 0.8100000000000000533 ) ) ; +#28110 = EDGE_LOOP ( 'NONE', ( #9049, #67482, #32815, #18525, #66100, #18207 ) ) ; +#28111 = ORIENTED_EDGE ( 'NONE', *, *, #54363, .T. ) ; +#28112 = SURFACE_STYLE_FILL_AREA ( #36278 ) ; +#28113 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#28114 = VECTOR ( 'NONE', #65052, 1000.000000000000000 ) ; +#28115 = SURFACE_SIDE_STYLE ('',( #91386 ) ) ; +#28116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68876 ), #47700 ) ; +#28117 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12371 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23638, #635, #8225 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28118 = PRESENTATION_STYLE_ASSIGNMENT (( #98462 ) ) ; +#28119 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28120 = EDGE_CURVE ( 'NONE', #44056, #75772, #98960, .T. ) ; +#28121 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37941 ), #5237 ) ; +#28122 = FILL_AREA_STYLE_COLOUR ( '', #46366 ) ; +#28123 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8648700000000000276 ) ) ; +#28124 = EDGE_LOOP ( 'NONE', ( #29903, #29073, #64751, #181 ) ) ; +#28125 = EDGE_LOOP ( 'NONE', ( #30092, #31214, #12174, #94673, #87958, #29816 ) ) ; +#28126 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24866 ), #80314 ) ; +#28127 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#28128 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22478 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19840, #51008, #18818 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28129 = CARTESIAN_POINT ( 'NONE', ( -0.2448925227682630101, -1.469666695271939938, 0.8100000000000000533 ) ) ; +#28130 = CARTESIAN_POINT ( 'NONE', ( -0.3663670119008199944, -1.086125944437150048, 0.8300000000000000711 ) ) ; +#28131 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80435 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46109, #5802, #61500 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28132 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28133 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#28134 = SURFACE_STYLE_FILL_AREA ( #67891 ) ; +#28135 = FILL_AREA_STYLE ('',( #91408 ) ) ; +#28136 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28137 = PLANE ( 'NONE', #49667 ) ; +#28138 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13310 ), #6813 ) ; +#28139 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28140 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28141 = VERTEX_POINT ( 'NONE', #52621 ) ; +#28142 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41191 ), #93312 ) ; +#28143 = EDGE_CURVE ( 'NONE', #7585, #77646, #83751, .T. ) ; +#28144 = PRESENTATION_STYLE_ASSIGNMENT (( #73594 ) ) ; +#28146 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#28145 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#28147 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28148 = PRESENTATION_STYLE_ASSIGNMENT (( #82275 ) ) ; +#28149 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33638, 'distance_accuracy_value', 'NONE'); +#28150 = ORIENTED_EDGE ( 'NONE', *, *, #28989, .T. ) ; +#28151 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.000000000000000000 ) ) ; +#28152 = SURFACE_SIDE_STYLE ('',( #70324 ) ) ; +#28153 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28154 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8199999999999999512 ) ) ; +#28155 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28156 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57469 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5474, #43821, #93123 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28157 = FILL_AREA_STYLE ('',( #29635 ) ) ; +#28158 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28159 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#28160 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#28161 = STYLED_ITEM ( 'NONE', ( #24477 ), #46977 ) ; +#28162 = SURFACE_STYLE_USAGE ( .BOTH. , #26668 ) ; +#28163 = EDGE_LOOP ( 'NONE', ( #24843, #45733, #18713, #20909 ) ) ; +#28164 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28165 = ORIENTED_EDGE ( 'NONE', *, *, #22440, .F. ) ; +#28166 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19295, 'distance_accuracy_value', 'NONE'); +#28167 = PRESENTATION_STYLE_ASSIGNMENT (( #84287 ) ) ; +#28168 = CARTESIAN_POINT ( 'NONE', ( -0.2223607051232819876, -1.054251812769849916, 0.8299999999999999600 ) ) ; +#28169 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28170 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37919 ), #15054 ) ; +#28171 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28172 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28173 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28174 = ORIENTED_EDGE ( 'NONE', *, *, #3903, .T. ) ; +#28175 = CYLINDRICAL_SURFACE ( 'NONE', #35262, 0.2000000000000005107 ) ; +#28176 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#28177 = PRESENTATION_STYLE_ASSIGNMENT (( #12260 ) ) ; +#28178 = ORIENTED_EDGE ( 'NONE', *, *, #8744, .T. ) ; +#28179 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28180 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28181 = VECTOR ( 'NONE', #85375, 1000.000000000000000 ) ; +#28182 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98204 ) ) ; +#28183 = ORIENTED_EDGE ( 'NONE', *, *, #51870, .F. ) ; +#28184 = EDGE_CURVE ( 'NONE', #60497, #52672, #38291, .T. ) ; +#28185 = EDGE_CURVE ( 'NONE', #25087, #40477, #91891, .T. ) ; +#28186 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98147 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28169, #49655, #42973 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28187 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28188 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39297 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75148, #90954, #23530 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28189 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28190 = FILL_AREA_STYLE ('',( #51687 ) ) ; +#28191 = ORIENTED_EDGE ( 'NONE', *, *, #99093, .T. ) ; +#28192 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59205 ), #85232 ) ; +#28193 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28194 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31649 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48870, #64677, #1387 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28195 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28196 = VERTEX_POINT ( 'NONE', #14236 ) ; +#28197 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#28198 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28199 = EDGE_LOOP ( 'NONE', ( #95384, #15864, #61499, #38621 ) ) ; +#28200 = EDGE_CURVE ( 'NONE', #77277, #80438, #601, .T. ) ; +#28201 = ORIENTED_EDGE ( 'NONE', *, *, #89479, .T. ) ; +#28202 = EDGE_CURVE ( 'NONE', #79071, #14803, #45397, .T. ) ; +#28203 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28204 = FILL_AREA_STYLE_COLOUR ( '', #7322 ) ; +#28205 = FACE_OUTER_BOUND ( 'NONE', #28125, .T. ) ; +#28206 = CARTESIAN_POINT ( 'NONE', ( -0.5701283774939980287, -1.188292975353419934, 0.8299999999999999600 ) ) ; +#28207 = SURFACE_STYLE_FILL_AREA ( #98548 ) ; +#28208 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39561 ), #41263 ) ; +#28210 = PRESENTATION_STYLE_ASSIGNMENT (( #72647 ) ) ; +#28209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28211 = VERTEX_POINT ( 'NONE', #93367 ) ; +#28212 = EDGE_CURVE ( 'NONE', #58838, #59417, #1506, .T. ) ; +#28213 = EDGE_LOOP ( 'NONE', ( #33448, #60779, #91356, #37560 ) ) ; +#28214 = ORIENTED_EDGE ( 'NONE', *, *, #64860, .T. ) ; +#28215 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#28217 = VERTEX_POINT ( 'NONE', #85239 ) ; +#28216 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28218 = EDGE_CURVE ( 'NONE', #18656, #81243, #71954, .T. ) ; +#28219 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28220 = SURFACE_STYLE_FILL_AREA ( #58894 ) ; +#28221 = SURFACE_SIDE_STYLE ('',( #67004 ) ) ; +#28222 = ORIENTED_EDGE ( 'NONE', *, *, #77402, .T. ) ; +#28223 = CARTESIAN_POINT ( 'NONE', ( -0.01837588986671732233, -1.004150690147872282, 0.8100000000002397504 ) ) ; +#28224 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#28225 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28226 = ORIENTED_EDGE ( 'NONE', *, *, #35326, .T. ) ; +#28227 = ADVANCED_FACE ( 'NONE', ( #100926 ), #9571, .F. ) ; +#28228 = CARTESIAN_POINT ( 'NONE', ( 0.3677412534775452713, -1.298963597675777626, 0.8100000000000002753 ) ) ; +#28229 = SURFACE_STYLE_USAGE ( .BOTH. , #88498 ) ; +#28230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60815 ), #3729 ) ; +#28231 = CARTESIAN_POINT ( 'NONE', ( 0.4905624295734890006, -1.210065939746389985, 0.8299999999999999600 ) ) ; +#28232 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25787 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86600, #24860, #61637 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28233 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78942 ) ) ; +#28234 = EDGE_CURVE ( 'NONE', #83515, #22417, #25012, .T. ) ; +#28235 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#28237 = EDGE_CURVE ( 'NONE', #13654, #25485, #85738, .T. ) ; +#28236 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28238 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4305 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16512, #8792, #24755 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28239 = VERTEX_POINT ( 'NONE', #95392 ) ; +#28240 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4849999999999999312, -0.2458578643762690530 ) ) ; +#28241 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28242 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36407 ) ) ; +#28243 = CARTESIAN_POINT ( 'NONE', ( 1.215713331845990064, -1.155903533527329996, 0.8300000000000022915 ) ) ; +#28244 = SURFACE_STYLE_FILL_AREA ( #90512 ) ; +#28246 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60838 ) ) ; +#28245 = LINE ( 'NONE', #68010, #29003 ) ; +#28247 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99136 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82453, #50822, #73293 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28248 = STYLED_ITEM ( 'NONE', ( #68777 ), #35175 ) ; +#28249 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28250 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28251 = VERTEX_POINT ( 'NONE', #64285 ) ; +#28252 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#28253 = STYLED_ITEM ( 'NONE', ( #83679 ), #36909 ) ; +#28254 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28255 = VERTEX_POINT ( 'NONE', #56144 ) ; +#28256 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28257 = ADVANCED_FACE ( 'NONE', ( #70410 ), #54635, .T. ) ; +#28258 = FILL_AREA_STYLE_COLOUR ( '', #4742 ) ; +#28259 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#28261 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65727 ), #77146 ) ; +#28260 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#28262 = SURFACE_STYLE_USAGE ( .BOTH. , #68536 ) ; +#28263 = VECTOR ( 'NONE', #26274, 1000.000000000000000 ) ; +#28264 = PRESENTATION_STYLE_ASSIGNMENT (( #99105 ) ) ; +#28265 = VECTOR ( 'NONE', #11042, 1000.000000000000000 ) ; +#28266 = SURFACE_STYLE_FILL_AREA ( #52758 ) ; +#28267 = SURFACE_STYLE_FILL_AREA ( #66545 ) ; +#28268 = PRESENTATION_STYLE_ASSIGNMENT (( #34937 ) ) ; +#28269 = VERTEX_POINT ( 'NONE', #35183 ) ; +#28270 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#28271 = EDGE_CURVE ( 'NONE', #36275, #19379, #73472, .T. ) ; +#28272 = FILL_AREA_STYLE_COLOUR ( '', #13112 ) ; +#28273 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#28274 = CARTESIAN_POINT ( 'NONE', ( 1.157750320739350247, -1.512608977738969962, 0.8300000000000010703 ) ) ; +#28275 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#28276 = VECTOR ( 'NONE', #77368, 1000.000000000000000 ) ; +#28277 = SURFACE_STYLE_FILL_AREA ( #43569 ) ; +#28278 = EDGE_CURVE ( 'NONE', #46200, #88969, #89281, .T. ) ; +#28279 = FILL_AREA_STYLE ('',( #90554 ) ) ; +#28280 = FILL_AREA_STYLE ('',( #14904 ) ) ; +#28281 = FILL_AREA_STYLE ('',( #75725 ) ) ; +#28282 = LINE ( 'NONE', #98140, #38708 ) ; +#28283 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28284 = ORIENTED_EDGE ( 'NONE', *, *, #31270, .F. ) ; +#28285 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28286 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28287 = VERTEX_POINT ( 'NONE', #80136 ) ; +#28288 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#28289 = FILL_AREA_STYLE ('',( #29768 ) ) ; +#28290 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#28291 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28292 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.09999999999999870104, -9.095983544939292593E-90 ) ) ; +#28293 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.17581999999999987, 0.8648700000000000276 ) ) ; +#28294 = LINE ( 'NONE', #83424, #57001 ) ; +#28295 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#28296 = VERTEX_POINT ( 'NONE', #88279 ) ; +#28297 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#28298 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000002720, 0.2458578643762690530 ) ) ; +#28299 = VECTOR ( 'NONE', #78843, 1000.000000000000000 ) ; +#28300 = LINE ( 'NONE', #67086, #60184 ) ; +#28301 = EDGE_LOOP ( 'NONE', ( #61337, #708, #33751, #75251 ) ) ; +#28302 = FILL_AREA_STYLE_COLOUR ( '', #77128 ) ; +#28303 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42936 ), #6980 ) ; +#28304 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6981 ), #68991 ) ; +#28305 = EDGE_CURVE ( 'NONE', #30664, #90348, #11580, .T. ) ; +#28306 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 9.801187639268928344E-18, -0.8499999999999999778 ) ) ; +#28307 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#28308 = CARTESIAN_POINT ( 'NONE', ( -1.285308266724690007, -1.390907012919420094, 0.8100000000000000533 ) ) ; +#28309 = AXIS2_PLACEMENT_3D ( 'NONE', #15391, #79754, #31243 ) ; +#28310 = PRESENTATION_STYLE_ASSIGNMENT (( #45570 ) ) ; +#28311 = ORIENTED_EDGE ( 'NONE', *, *, #74934, .T. ) ; +#28312 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28313 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72312 ) ) ; +#28314 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64173 ), #46190 ) ; +#28315 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68988, #29710, #37889, #77175, #100053, #54216, #7147, #70014, #91499, #91990, #38397, #21550, #29226, #46000, #15876, #30198, #14845, #99565, #46522 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.895499375637886810E-05, 3.738329657103213428E-05, 5.527352819117126555E-05, 7.271121307565113316E-05, 8.968733045764483349E-05, 0.0001061612447615763112, 0.0001221153084768654765, 0.0001378567193849194756, 0.0001535008571834024283, 0.0001692684803906364564, 0.0001854697664425697932, 0.0002020894132512514112, 0.0002193451494927627272, 0.0002374891443265937153, 0.0002566052952319094224, 0.0002770255913895464084 ), + .UNSPECIFIED. ) ; +#28317 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#28316 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28318 = ORIENTED_EDGE ( 'NONE', *, *, #73200, .T. ) ; +#28319 = ADVANCED_FACE ( 'NONE', ( #51000 ), #50510, .T. ) ; +#28320 = VECTOR ( 'NONE', #44668, 1000.000000000000000 ) ; +#28321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #524 ), #83560 ) ; +#28322 = SURFACE_SIDE_STYLE ('',( #90600 ) ) ; +#28323 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28324 = VERTEX_POINT ( 'NONE', #43307 ) ; +#28325 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61242 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85612, #31492, #46794 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28326 = VECTOR ( 'NONE', #1565, 1000.000000000000000 ) ; +#28327 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72336 ), #85372 ) ; +#28328 = AXIS2_PLACEMENT_3D ( 'NONE', #36926, #45527, #83886 ) ; +#28329 = ORIENTED_EDGE ( 'NONE', *, *, #42837, .T. ) ; +#28331 = ORIENTED_EDGE ( 'NONE', *, *, #60652, .T. ) ; +#28330 = CARTESIAN_POINT ( 'NONE', ( 1.076179938779914913, 3.099999999999980549, 0.000000000000000000 ) ) ; +#28332 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45883, 'distance_accuracy_value', 'NONE'); +#28333 = CARTESIAN_POINT ( 'NONE', ( 6.728456872965260516, 10.75427687296526003, 0.8648700000000000276 ) ) ; +#28335 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 2.168404344971010347E-16 ) ) ; +#28334 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28336 = LINE ( 'NONE', #59526, #92066 ) ; +#28337 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28338 = FILL_AREA_STYLE_COLOUR ( '', #66724 ) ; +#28339 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8648700000000000276 ) ) ; +#28340 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28341 = ORIENTED_EDGE ( 'NONE', *, *, #9559, .F. ) ; +#28342 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#28343 = LINE ( 'NONE', #82478, #74353 ) ; +#28344 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7031 ) ) ; +#28345 = ORIENTED_EDGE ( 'NONE', *, *, #9400, .T. ) ; +#28347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28346 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999853, 0.8648700000000000276 ) ) ; +#28348 = VERTEX_POINT ( 'NONE', #41821 ) ; +#28349 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28350 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#28352 = EDGE_CURVE ( 'NONE', #15467, #42470, #66782, .T. ) ; +#28351 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#28353 = VECTOR ( 'NONE', #31122, 1000.000000000000000 ) ; +#28354 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#28355 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#28356 = VERTEX_POINT ( 'NONE', #50004 ) ; +#28357 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#28358 = ORIENTED_EDGE ( 'NONE', *, *, #93069, .F. ) ; +#28359 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28361 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28360 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28362 = PRESENTATION_STYLE_ASSIGNMENT (( #99686 ) ) ; +#28363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28364 = LINE ( 'NONE', #5826, #3431 ) ; +#28366 = AXIS2_PLACEMENT_3D ( 'NONE', #6708, #7214, #69040 ) ; +#28365 = FILL_AREA_STYLE ('',( #19698 ) ) ; +#28367 = STYLED_ITEM ( 'NONE', ( #82203 ), #26450 ) ; +#28368 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28369 = EDGE_LOOP ( 'NONE', ( #98814, #33387, #91166, #95987 ) ) ; +#28370 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28371 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#28372 = EDGE_CURVE ( 'NONE', #32075, #76735, #57678, .T. ) ; +#28373 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28375 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#28374 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#28376 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10609, 'distance_accuracy_value', 'NONE'); +#28377 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#28379 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70780 ), #2309 ) ; +#28380 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#28381 = PLANE ( 'NONE', #87735 ) ; +#28382 = FILL_AREA_STYLE ('',( #67170 ) ) ; +#28383 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28384 = ORIENTED_EDGE ( 'NONE', *, *, #46820, .T. ) ; +#28385 = EDGE_CURVE ( 'NONE', #37356, #90340, #88777, .T. ) ; +#28386 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#28387 = STYLED_ITEM ( 'NONE', ( #28264 ), #28971 ) ; +#28388 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28389 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28390 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#28392 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#28391 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#28393 = LINE ( 'NONE', #84022, #86988 ) ; +#28394 = PRESENTATION_STYLE_ASSIGNMENT (( #20725 ) ) ; +#28395 = AXIS2_PLACEMENT_3D ( 'NONE', #99027, #12273, #43995 ) ; +#28396 = FACE_OUTER_BOUND ( 'NONE', #27826, .T. ) ; +#28397 = CARTESIAN_POINT ( 'NONE', ( 0.7666666666666606123, -3.500000000000000000, 0.000000000000000000 ) ) ; +#28398 = PRESENTATION_STYLE_ASSIGNMENT (( #42713 ) ) ; +#28399 = SURFACE_STYLE_USAGE ( .BOTH. , #58576 ) ; +#28400 = SURFACE_SIDE_STYLE ('',( #4396 ) ) ; +#28401 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28402 = EDGE_CURVE ( 'NONE', #64661, #34720, #48984, .T. ) ; +#28403 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28404 = FILL_AREA_STYLE ('',( #49902 ) ) ; +#28405 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#28406 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90344 ) ) ; +#28407 = CARTESIAN_POINT ( 'NONE', ( -0.2353471038102170343, -0.9412361261466359874, 0.8300000000000009592 ) ) ; +#28408 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28410 = EDGE_CURVE ( 'NONE', #14207, #48067, #49481, .T. ) ; +#28409 = SURFACE_STYLE_USAGE ( .BOTH. , #67682 ) ; +#28411 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28412 = ORIENTED_EDGE ( 'NONE', *, *, #34105, .F. ) ; +#28413 = FILL_AREA_STYLE ('',( #21240 ) ) ; +#28414 = PRESENTATION_STYLE_ASSIGNMENT (( #90698 ) ) ; +#28416 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#28415 = PRESENTATION_STYLE_ASSIGNMENT (( #98281 ) ) ; +#28417 = LINE ( 'NONE', #91681, #8284 ) ; +#28418 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72417 ) ) ; +#28419 = EDGE_CURVE ( 'NONE', #47598, #34589, #34681, .T. ) ; +#28420 = FILL_AREA_STYLE ('',( #27940 ) ) ; +#28421 = ORIENTED_EDGE ( 'NONE', *, *, #3516, .F. ) ; +#28422 = CARTESIAN_POINT ( 'NONE', ( -0.4333333333333340143, -3.500000000000000000, 0.000000000000000000 ) ) ; +#28423 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28424 = VERTEX_POINT ( 'NONE', #3007 ) ; +#28425 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28426 = EDGE_CURVE ( 'NONE', #28356, #14217, #65806, .T. ) ; +#28427 = ADVANCED_FACE ( 'NONE', ( #96905 ), #27514, .T. ) ; +#28428 = LINE ( 'NONE', #35611, #98325 ) ; +#28429 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28430 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37629 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93978, #8668, #17412 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28431 = SURFACE_STYLE_FILL_AREA ( #76381 ) ; +#28432 = VERTEX_POINT ( 'NONE', #29974 ) ; +#28433 = ORIENTED_EDGE ( 'NONE', *, *, #57789, .F. ) ; +#28434 = AXIS2_PLACEMENT_3D ( 'NONE', #3017, #42830, #41829 ) ; +#28435 = EDGE_CURVE ( 'NONE', #25651, #88953, #2365, .T. ) ; +#28436 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54546 ), #80644 ) ; +#28437 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#28438 = VERTEX_POINT ( 'NONE', #21331 ) ; +#28439 = CARTESIAN_POINT ( 'NONE', ( 1.823253843827010057, -1.327673353236110021, 0.8299999999999999600 ) ) ; +#28440 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#28441 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43079 ), #93545 ) ; +#28442 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28443 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28444 = SURFACE_STYLE_FILL_AREA ( #42753 ) ; +#28445 = EDGE_CURVE ( 'NONE', #17483, #64267, #68282, .T. ) ; +#28446 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #87726, #82894 ) ; +#28448 = VERTEX_POINT ( 'NONE', #52490 ) ; +#28447 = ORIENTED_EDGE ( 'NONE', *, *, #45697, .T. ) ; +#28449 = ORIENTED_EDGE ( 'NONE', *, *, #74092, .F. ) ; +#28450 = VERTEX_POINT ( 'NONE', #84625 ) ; +#28451 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28452 = LINE ( 'NONE', #60615, #6731 ) ; +#28453 = VECTOR ( 'NONE', #69386, 1000.000000000000000 ) ; +#28455 = STYLED_ITEM ( 'NONE', ( #80409 ), #20272 ) ; +#28454 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86019, 'distance_accuracy_value', 'NONE'); +#28456 = CARTESIAN_POINT ( 'NONE', ( 1.302823766419570317, -0.9018902076549569768, 0.8100000000000000533 ) ) ; +#28457 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82260 ), #47981 ) ; +#28458 = SURFACE_SIDE_STYLE ('',( #75411 ) ) ; +#28459 = PRESENTATION_STYLE_ASSIGNMENT (( #67733 ) ) ; +#28460 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35047 ) ) ; +#28461 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28462 = ORIENTED_EDGE ( 'NONE', *, *, #12098, .F. ) ; +#28464 = SURFACE_STYLE_USAGE ( .BOTH. , #19798 ) ; +#28463 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28465 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13165 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10827, #41565, #72698 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28466 = ORIENTED_EDGE ( 'NONE', *, *, #14939, .T. ) ; +#28467 = ORIENTED_EDGE ( 'NONE', *, *, #100623, .T. ) ; +#28468 = CARTESIAN_POINT ( 'NONE', ( 1.236552921348300194, -1.233317951191559958, 0.8299999999999999600 ) ) ; +#28469 = STYLED_ITEM ( 'NONE', ( #19725 ), #97861 ) ; +#28470 = PLANE ( 'NONE', #67860 ) ; +#28471 = CARTESIAN_POINT ( 'NONE', ( 3.100999124875012392, 7.282381875124987580, 0.8991599999999999593 ) ) ; +#28472 = ADVANCED_FACE ( 'NONE', ( #74969 ), #4981, .T. ) ; +#28473 = ORIENTED_EDGE ( 'NONE', *, *, #99281, .T. ) ; +#28474 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.523820061220085176, 0.000000000000000000 ) ) ; +#28475 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28476 = SURFACE_STYLE_FILL_AREA ( #51974 ) ; +#28477 = ORIENTED_EDGE ( 'NONE', *, *, #14706, .T. ) ; +#28478 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28479 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28480 = ORIENTED_EDGE ( 'NONE', *, *, #20910, .F. ) ; +#28481 = EDGE_CURVE ( 'NONE', #10043, #87090, #14126, .T. ) ; +#28482 = VERTEX_POINT ( 'NONE', #6450 ) ; +#28483 = SURFACE_STYLE_USAGE ( .BOTH. , #36664 ) ; +#28484 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28485 = VECTOR ( 'NONE', #43870, 1000.000000000000000 ) ; +#28486 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28487 = AXIS2_PLACEMENT_3D ( 'NONE', #71159, #18009, #87486 ) ; +#28488 = SURFACE_STYLE_FILL_AREA ( #97867 ) ; +#28489 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59977, 'distance_accuracy_value', 'NONE'); +#28490 = EDGE_LOOP ( 'NONE', ( #79293, #61400, #15292, #45723, #55123, #45256, #14784, #21515 ) ) ; +#28491 = ORIENTED_EDGE ( 'NONE', *, *, #39928, .F. ) ; +#28492 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84158 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98233, #43667, #12970 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28493 = CARTESIAN_POINT ( 'NONE', ( -0.04570195398950489818, -0.9814610950457439698, 0.8100000000000000533 ) ) ; +#28494 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28496 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28495 = VECTOR ( 'NONE', #81174, 1000.000000000000000 ) ; +#28497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79089 ) ) ; +#28498 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11686, #19443, #26124, #50621 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#28499 = SURFACE_SIDE_STYLE ('',( #98362 ) ) ; +#28500 = PRESENTATION_STYLE_ASSIGNMENT (( #99350 ) ) ; +#28501 = ORIENTED_EDGE ( 'NONE', *, *, #95251, .F. ) ; +#28502 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#28503 = STYLED_ITEM ( 'NONE', ( #20520 ), #82140 ) ; +#28505 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -2.168404344971010347E-16 ) ) ; +#28504 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70851 ) ) ; +#28506 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#28507 = SURFACE_SIDE_STYLE ('',( #98857 ) ) ; +#28508 = LINE ( 'NONE', #68294, #25220 ) ; +#28509 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3299 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13642, #69296, #77502 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28510 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.05000000000000002359, 0.1900000000000000022 ) ) ; +#28511 = FILL_AREA_STYLE_COLOUR ( '', #12983 ) ; +#28513 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28512 = AXIS2_PLACEMENT_3D ( 'NONE', #83575, #77395, #24709 ) ; +#28514 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28515 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000000104, 0.2458578643762690530 ) ) ; +#28516 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#28517 = VECTOR ( 'NONE', #5749, 1000.000000000000114 ) ; +#28519 = ORIENTED_EDGE ( 'NONE', *, *, #21366, .F. ) ; +#28518 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59175 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55186, #61824, #506 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28520 = LINE ( 'NONE', #75487, #9516 ) ; +#28521 = LINE ( 'NONE', #59722, #65556 ) ; +#28522 = VERTEX_POINT ( 'NONE', #37674 ) ; +#28523 = FILL_AREA_STYLE_COLOUR ( '', #64162 ) ; +#28524 = FILL_AREA_STYLE_COLOUR ( '', #61675 ) ; +#28525 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.676179938779915002, -0.02000000000000000042 ) ) ; +#28526 = PLANE ( 'NONE', #92512 ) ; +#28527 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28528 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69929 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69141, #84018, #28389 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28529 = CARTESIAN_POINT ( 'NONE', ( 1.416666666666666519, 3.099999999999969891, 0.000000000000000000 ) ) ; +#28530 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146561253, 0.2541340759269652416, 0.8100000000000000533 ) ) ; +#28531 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, 3.500000000000000444, 0.000000000000000000 ) ) ; +#28532 = VECTOR ( 'NONE', #33562, 1000.000000000000000 ) ; +#28533 = ORIENTED_EDGE ( 'NONE', *, *, #11384, .F. ) ; +#28534 = AXIS2_PLACEMENT_3D ( 'NONE', #92696, #53944, #46230 ) ; +#28535 = SURFACE_STYLE_USAGE ( .BOTH. , #13641 ) ; +#28536 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#28537 = SURFACE_STYLE_FILL_AREA ( #59736 ) ; +#28538 = ADVANCED_FACE ( 'NONE', ( #68771 ), #99821, .T. ) ; +#28539 = SURFACE_SIDE_STYLE ('',( #75021 ) ) ; +#28540 = STYLED_ITEM ( 'NONE', ( #42193 ), #12535 ) ; +#28541 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#28542 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701290252, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#28543 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28544 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#28545 = ORIENTED_EDGE ( 'NONE', *, *, #15994, .T. ) ; +#28546 = EDGE_LOOP ( 'NONE', ( #26929, #57436, #8771, #18366 ) ) ; +#28547 = PRESENTATION_STYLE_ASSIGNMENT (( #41379 ) ) ; +#28548 = ORIENTED_EDGE ( 'NONE', *, *, #7122, .F. ) ; +#28549 = SURFACE_SIDE_STYLE ('',( #20893 ) ) ; +#28550 = LINE ( 'NONE', #42877, #58134 ) ; +#28551 = SURFACE_SIDE_STYLE ('',( #98415 ) ) ; +#28552 = EDGE_CURVE ( 'NONE', #53312, #97109, #48379, .T. ) ; +#28553 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -2.184558957341043599E-17, 0.6199999999999999956 ) ) ; +#28554 = CARTESIAN_POINT ( 'NONE', ( -0.5417956820186821121, -0.9001291024598061519, 0.8100000000000000533 ) ) ; +#28555 = CARTESIAN_POINT ( 'NONE', ( -1.204376861304429891, -0.9585643914498560569, 0.8299999999999999600 ) ) ; +#28556 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39826 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53877, #55740, #78690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28558 = VERTEX_POINT ( 'NONE', #31503 ) ; +#28557 = ORIENTED_EDGE ( 'NONE', *, *, #59392, .T. ) ; +#28559 = ORIENTED_EDGE ( 'NONE', *, *, #35738, .F. ) ; +#28560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59500 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42109, #27813, #89072 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28561 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84644, 'distance_accuracy_value', 'NONE'); +#28562 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28563 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29436, 'distance_accuracy_value', 'NONE'); +#28565 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#28564 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#28566 = ORIENTED_EDGE ( 'NONE', *, *, #61728, .T. ) ; +#28568 = ORIENTED_EDGE ( 'NONE', *, *, #18275, .F. ) ; +#28567 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28569 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28570 = AXIS2_PLACEMENT_3D ( 'NONE', #11158, #42407, #3599 ) ; +#28571 = VECTOR ( 'NONE', #3776, 1000.000000000000114 ) ; +#28572 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999985359, -0.1458578643762690474 ) ) ; +#28573 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28574 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#28575 = EDGE_LOOP ( 'NONE', ( #51546, #99040, #9654, #59142 ) ) ; +#28576 = VERTEX_POINT ( 'NONE', #93745 ) ; +#28577 = VECTOR ( 'NONE', #3924, 1000.000000000000000 ) ; +#28578 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62783 ) ) ; +#28579 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28580 = ORIENTED_EDGE ( 'NONE', *, *, #67894, .F. ) ; +#28581 = AXIS2_PLACEMENT_3D ( 'NONE', #56739, #16859, #1587 ) ; +#28583 = ORIENTED_EDGE ( 'NONE', *, *, #45153, .T. ) ; +#28582 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28584 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#28585 = ORIENTED_EDGE ( 'NONE', *, *, #43828, .T. ) ; +#28586 = LINE ( 'NONE', #37282, #33800 ) ; +#28587 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#28588 = EDGE_LOOP ( 'NONE', ( #72962, #94967, #14152, #92356 ) ) ; +#28589 = EDGE_CURVE ( 'NONE', #47242, #91365, #24892, .T. ) ; +#28590 = VERTEX_POINT ( 'NONE', #47325 ) ; +#28591 = FACE_OUTER_BOUND ( 'NONE', #91105, .T. ) ; +#28592 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6761799387799151129, 0.000000000000000000 ) ) ; +#28594 = VECTOR ( 'NONE', #79489, 1000.000000000000114 ) ; +#28593 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66139 ), #20427 ) ; +#28596 = LINE ( 'NONE', #6053, #49866 ) ; +#28597 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76050 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47683, #93091, #63540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28598 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59635 ), #67638 ) ; +#28599 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28600 = PRESENTATION_STYLE_ASSIGNMENT (( #20948 ) ) ; +#28602 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28601 = LINE ( 'NONE', #27630, #38319 ) ; +#28603 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#28604 = ORIENTED_EDGE ( 'NONE', *, *, #99501, .F. ) ; +#28605 = PRESENTATION_STYLE_ASSIGNMENT (( #67399 ) ) ; +#28606 = CARTESIAN_POINT ( 'NONE', ( -1.005612341081159933, -1.485054850390570058, 0.8299999999999999600 ) ) ; +#28607 = VERTEX_POINT ( 'NONE', #55017 ) ; +#28608 = STYLED_ITEM ( 'NONE', ( #71666 ), #3553 ) ; +#28609 = FILL_AREA_STYLE ('',( #83257 ) ) ; +#28611 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79201 ) ) ; +#28610 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, 0.000000000000000000 ) ) ; +#28612 = FILL_AREA_STYLE ('',( #51633 ) ) ; +#28614 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.500000000000000000, -1.195472123049164304E-89 ) ) ; +#28613 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28615 = PLANE ( 'NONE', #35740 ) ; +#28616 = CARTESIAN_POINT ( 'NONE', ( 1.739573088979520010, -1.154690592117219916, 0.8299999999999999600 ) ) ; +#28617 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28618 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#28619 = EDGE_CURVE ( 'NONE', #73267, #70482, #72531, .T. ) ; +#28620 = SURFACE_STYLE_USAGE ( .BOTH. , #3639 ) ; +#28621 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#28622 = VECTOR ( 'NONE', #40801, 1000.000000000000000 ) ; +#28623 = EDGE_CURVE ( 'NONE', #33842, #50596, #7217, .T. ) ; +#28624 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#28625 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28626 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12224 ) ) ; +#28628 = LINE ( 'NONE', #67422, #87698 ) ; +#28627 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28629 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28630 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#28631 = PRESENTATION_STYLE_ASSIGNMENT (( #98980 ) ) ; +#28632 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#28633 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20461 ) ) ; +#28634 = ORIENTED_EDGE ( 'NONE', *, *, #70414, .F. ) ; +#28635 = CARTESIAN_POINT ( 'NONE', ( -1.018373906775690063, -1.409018172687890091, 0.8299999999999999600 ) ) ; +#28636 = EDGE_CURVE ( 'NONE', #94339, #54968, #7434, .T. ) ; +#28637 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28638 = EDGE_CURVE ( 'NONE', #82318, #79398, #7931, .T. ) ; +#28639 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1350000000000000089 ) ) ; +#28640 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.323820061220084998, -0.02000000000000000042 ) ) ; +#28641 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31934 ) ) ; +#28642 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28643 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 2.766452331408968662E-179, 0.4500000000000001221 ) ) ; +#28644 = STYLED_ITEM ( 'NONE', ( #41300 ), #78538 ) ; +#28645 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#28646 = LINE ( 'NONE', #5124, #49687 ) ; +#28647 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #96220 ) ; +#28648 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15572 ) ) ; +#28649 = ORIENTED_EDGE ( 'NONE', *, *, #55673, .T. ) ; +#28650 = ORIENTED_EDGE ( 'NONE', *, *, #26882, .F. ) ; +#28651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38066, 'distance_accuracy_value', 'NONE'); +#28652 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57829, 'distance_accuracy_value', 'NONE'); +#28653 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8648700000000000276 ) ) ; +#28654 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, -8.400000000000000355, -11.82000000000000028 ) ) ; +#28655 = PRESENTATION_STYLE_ASSIGNMENT (( #54154 ) ) ; +#28656 = ADVANCED_FACE ( 'N', ( #86638 ), #39667, .F. ) ; +#28657 = PRESENTATION_STYLE_ASSIGNMENT (( #99006 ) ) ; +#28658 = STYLED_ITEM ( 'NONE', ( #53652 ), #15691 ) ; +#28659 = PLANE ( 'NONE', #25845 ) ; +#28660 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 4.142826999999999593, 0.8648700000000000276 ) ) ; +#28661 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36837 ), #17203 ) ; +#28662 = SURFACE_STYLE_USAGE ( .BOTH. , #89939 ) ; +#28663 = VERTEX_POINT ( 'NONE', #100813 ) ; +#28664 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28666 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28665 = PLANE ( 'NONE', #39498 ) ; +#28667 = ORIENTED_EDGE ( 'NONE', *, *, #12806, .F. ) ; +#28668 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8648700000000000276 ) ) ; +#28669 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15587 ), #67849 ) ; +#28670 = ORIENTED_EDGE ( 'NONE', *, *, #12003, .F. ) ; +#28671 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28672 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28674 = ADVANCED_FACE ( 'NONE', ( #92748 ), #80009, .T. ) ; +#28675 = VECTOR ( 'NONE', #18892, 1000.000000000000000 ) ; +#28676 = DIRECTION ( 'NONE', ( -0.7071067811865465735, -0.7071067811865485719, 0.000000000000000000 ) ) ; +#28677 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28678 = FILL_AREA_STYLE_COLOUR ( '', #61063 ) ; +#28679 = ORIENTED_EDGE ( 'NONE', *, *, #39599, .F. ) ; +#28680 = AXIS2_PLACEMENT_3D ( 'NONE', #82106, #26473, #58141 ) ; +#28681 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28682 = EDGE_LOOP ( 'NONE', ( #87345, #29323, #23302, #65959 ) ) ; +#28683 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90432 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45715, #100263, #7875 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28685 = CARTESIAN_POINT ( 'NONE', ( -0.4563726483146510193, -1.022509610276640002, 0.8299999999999999600 ) ) ; +#28684 = FACE_OUTER_BOUND ( 'NONE', #31839, .T. ) ; +#28686 = VERTEX_POINT ( 'NONE', #95266 ) ; +#28687 = EDGE_LOOP ( 'NONE', ( #77949, #34749, #21291, #4110 ) ) ; +#28688 = SURFACE_SIDE_STYLE ('',( #4689 ) ) ; +#28689 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#28690 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8100000000000000533 ) ) ; +#28691 = PRESENTATION_STYLE_ASSIGNMENT (( #82826 ) ) ; +#28692 = EDGE_CURVE ( 'NONE', #25440, #71164, #97287, .T. ) ; +#28693 = CYLINDRICAL_SURFACE ( 'NONE', #70849, 1.968750814464449883 ) ; +#28694 = VERTEX_POINT ( 'NONE', #3879 ) ; +#28696 = ORIENTED_EDGE ( 'NONE', *, *, #5646, .T. ) ; +#28695 = VECTOR ( 'NONE', #95247, 1000.000000000000000 ) ; +#28697 = ORIENTED_EDGE ( 'NONE', *, *, #25665, .T. ) ; +#28698 = CARTESIAN_POINT ( 'NONE', ( 6.728456745930520455, 10.75427674593051819, 0.8991599999999999593 ) ) ; +#28699 = STYLED_ITEM ( 'NONE', ( #21318 ), #30028 ) ; +#28700 = ORIENTED_EDGE ( 'NONE', *, *, #13969, .F. ) ; +#28701 = CIRCLE ( 'NONE', #20529, 0.2000000000000005107 ) ; +#28702 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28703 = VERTEX_POINT ( 'NONE', #19710 ) ; +#28704 = CARTESIAN_POINT ( 'NONE', ( -0.08221093278894474332, -0.9628029020972094232, 0.8100000000003017009 ) ) ; +#28705 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#28706 = VERTEX_POINT ( 'NONE', #3398 ) ; +#28707 = ADVANCED_FACE ( 'NONE', ( #35060 ), #18164, .T. ) ; +#28708 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16430 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7750, #52322, #83453 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28709 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000002289, 0.8991599999999999593 ) ) ; +#28710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28711 = CARTESIAN_POINT ( 'NONE', ( 0.4504580075531440242, -1.245164908316749974, 0.8299999999999999600 ) ) ; +#28712 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48142 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25860, #95234, #2364 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28713 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72753 ) ) ; +#28714 = LINE ( 'NONE', #20047, #80374 ) ; +#28715 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#28716 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#28717 = SURFACE_STYLE_USAGE ( .BOTH. , #69508 ) ; +#28718 = EDGE_LOOP ( 'NONE', ( #28634, #12815, #88769, #80615 ) ) ; +#28719 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, 0.4750000000000000333, -0.2500000000000000000 ) ) ; +#28720 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40192 ), #38570 ) ; +#28721 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#28723 = CARTESIAN_POINT ( 'NONE', ( 1.592240980523089933, -1.399421068953929925, 0.8299999999999999600 ) ) ; +#28722 = CARTESIAN_POINT ( 'NONE', ( 0.4481429611221979803, -1.007711706028959986, 0.8100000000000000533 ) ) ; +#28724 = SURFACE_SIDE_STYLE ('',( #46015 ) ) ; +#28725 = FACE_OUTER_BOUND ( 'NONE', #92810, .T. ) ; +#28726 = STYLED_ITEM ( 'NONE', ( #23837 ), #39376 ) ; +#28727 = STYLED_ITEM ( 'NONE', ( #6828 ), #99641 ) ; +#28728 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28729 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#28730 = VERTEX_POINT ( 'NONE', #89666 ) ; +#28731 = VECTOR ( 'NONE', #18333, 1000.000000000000000 ) ; +#28732 = EDGE_CURVE ( 'NONE', #4688, #65011, #82017, .T. ) ; +#28733 = SURFACE_SIDE_STYLE ('',( #54642 ) ) ; +#28734 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28735 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28736 = ORIENTED_EDGE ( 'NONE', *, *, #8623, .F. ) ; +#28737 = CARTESIAN_POINT ( 'NONE', ( -0.8280235389610388630, 0.7099999999999999645, -6.098637220230962441E-17 ) ) ; +#28739 = PLANE ( 'NONE', #16763 ) ; +#28738 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28740 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28741 = AXIS2_PLACEMENT_3D ( 'NONE', #20161, #61013, #14480 ) ; +#28742 = EDGE_CURVE ( 'NONE', #76430, #44999, #95774, .T. ) ; +#28743 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28745 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28746 = ORIENTED_EDGE ( 'NONE', *, *, #18320, .T. ) ; +#28747 = PLANE ( 'NONE', #13042 ) ; +#28748 = ADVANCED_FACE ( 'NONE', ( #56541 ), #87649, .T. ) ; +#28749 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8991599999999999593 ) ) ; +#28750 = EDGE_CURVE ( 'NONE', #4442, #85319, #77264, .T. ) ; +#28751 = SURFACE_STYLE_FILL_AREA ( #37446 ) ; +#28752 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#28753 = PRESENTATION_STYLE_ASSIGNMENT (( #53257 ) ) ; +#28754 = FACE_OUTER_BOUND ( 'NONE', #80726, .T. ) ; +#28755 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28756 = EDGE_CURVE ( 'NONE', #100163, #16557, #90661, .T. ) ; +#28757 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87443 ) ) ; +#28758 = LINE ( 'NONE', #5743, #81726 ) ; +#28759 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28760 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40056, 'distance_accuracy_value', 'NONE'); +#28761 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28762 = ORIENTED_EDGE ( 'NONE', *, *, #49538, .F. ) ; +#28763 = PLANE ( 'NONE', #46417 ) ; +#28764 = ORIENTED_EDGE ( 'NONE', *, *, #15957, .F. ) ; +#28765 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5901, 'distance_accuracy_value', 'NONE'); +#28766 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79402, 'distance_accuracy_value', 'NONE'); +#28767 = PLANE ( 'NONE', #7056 ) ; +#28768 = EDGE_CURVE ( 'NONE', #19781, #83746, #20706, .T. ) ; +#28769 = STYLED_ITEM ( 'NONE', ( #87496 ), #83757 ) ; +#28770 = AXIS2_PLACEMENT_3D ( 'NONE', #73705, #26759, #33921 ) ; +#28771 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#28772 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28773 = LINE ( 'NONE', #4783, #6386 ) ; +#28774 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#28775 = ORIENTED_EDGE ( 'NONE', *, *, #69961, .F. ) ; +#28777 = SURFACE_STYLE_FILL_AREA ( #98644 ) ; +#28776 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20267 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62689, #93756, #77467 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28778 = SURFACE_STYLE_USAGE ( .BOTH. , #51789 ) ; +#28779 = EDGE_CURVE ( 'NONE', #18396, #80677, #96798, .T. ) ; +#28780 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5699, 'distance_accuracy_value', 'NONE'); +#28781 = STYLED_ITEM ( 'NONE', ( #75680 ), #83181 ) ; +#28782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90737 ) ) ; +#28783 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28784 = ORIENTED_EDGE ( 'NONE', *, *, #95741, .F. ) ; +#28785 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15038, #85031, #86556, #31419 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#28786 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28787 = EDGE_CURVE ( 'NONE', #84546, #18495, #37557, .T. ) ; +#28788 = VECTOR ( 'NONE', #79051, 1000.000000000000000 ) ; +#28790 = EDGE_CURVE ( 'NONE', #30962, #66452, #91641, .T. ) ; +#28789 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#28791 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82602 ) ) ; +#28792 = VERTEX_POINT ( 'NONE', #37054 ) ; +#28793 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#28794 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69540, 'distance_accuracy_value', 'NONE'); +#28796 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15802 ) ) ; +#28798 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28799 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28800 = CLOSED_SHELL ( 'NONE', ( #65791, #97265, #85816, #50903, #45852, #62267 ) ) ; +#28801 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #13944 ) ) ; +#28802 = ORIENTED_EDGE ( 'NONE', *, *, #74819, .T. ) ; +#28803 = STYLED_ITEM ( 'NONE', ( #90791 ), #39598 ) ; +#28804 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22316 ) ) ; +#28805 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28806 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28807 = SURFACE_SIDE_STYLE ('',( #98668 ) ) ; +#28808 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999951039, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#28809 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28810 = EDGE_LOOP ( 'NONE', ( #11232, #28178, #35866, #32299 ) ) ; +#28811 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66952 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50232, #4714, #4227 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28812 = EDGE_CURVE ( 'NONE', #47416, #75802, #83003, .T. ) ; +#28813 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33734 ), #2523 ) ; +#28814 = VERTEX_POINT ( 'NONE', #52377 ) ; +#28816 = ORIENTED_EDGE ( 'NONE', *, *, #74663, .T. ) ; +#28815 = SURFACE_STYLE_FILL_AREA ( #97712 ) ; +#28817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89185 ), #66372 ) ; +#28818 = LINE ( 'NONE', #37001, #81721 ) ; +#28819 = FACE_OUTER_BOUND ( 'NONE', #97874, .T. ) ; +#28820 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#28821 = ORIENTED_EDGE ( 'NONE', *, *, #76081, .F. ) ; +#28822 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28823 = SURFACE_STYLE_USAGE ( .BOTH. , #75303 ) ; +#28824 = ORIENTED_EDGE ( 'NONE', *, *, #73771, .T. ) ; +#28825 = EDGE_CURVE ( 'NONE', #30201, #94205, #75334, .T. ) ; +#28826 = LINE ( 'NONE', #60011, #4161 ) ; +#28827 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28828 = FACE_OUTER_BOUND ( 'NONE', #22812, .T. ) ; +#28829 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28830 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14138 ), #90799 ) ; +#28831 = ORIENTED_EDGE ( 'NONE', *, *, #76296, .F. ) ; +#28832 = EDGE_CURVE ( 'NONE', #4416, #65839, #36055, .T. ) ; +#28833 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38602 ), #40304 ) ; +#28834 = CARTESIAN_POINT ( 'NONE', ( 1.766025874245259697, -1.139163918933580266, 0.8099999999999998312 ) ) ; +#28835 = VERTEX_POINT ( 'NONE', #53361 ) ; +#28837 = FILL_AREA_STYLE ('',( #98701 ) ) ; +#28836 = FILL_AREA_STYLE_COLOUR ( '', #64202 ) ; +#28838 = STYLED_ITEM ( 'NONE', ( #94399 ), #30566 ) ; +#28839 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28841 = EDGE_CURVE ( 'NONE', #52188, #77034, #36556, .T. ) ; +#28840 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#28842 = EDGE_LOOP ( 'NONE', ( #37158, #83093, #86838, #70126 ) ) ; +#28843 = VERTEX_POINT ( 'NONE', #74340 ) ; +#28844 = SURFACE_STYLE_FILL_AREA ( #12951 ) ; +#28846 = FILL_AREA_STYLE ('',( #30325 ) ) ; +#28845 = SURFACE_STYLE_FILL_AREA ( #70152 ) ; +#28847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#28848 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67238 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15540, #85008, #85515 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28849 = SURFACE_STYLE_USAGE ( .BOTH. , #4855 ) ; +#28850 = STYLED_ITEM ( 'NONE', ( #35914 ), #79012 ) ; +#28851 = LINE ( 'NONE', #76821, #37675 ) ; +#28852 = LINE ( 'NONE', #61539, #90331 ) ; +#28853 = EDGE_CURVE ( 'NONE', #23180, #1626, #21704, .T. ) ; +#28855 = EDGE_CURVE ( 'NONE', #26813, #41762, #68154, .T. ) ; +#28854 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#28856 = CARTESIAN_POINT ( 'NONE', ( 4.953618875124988108, 3.393294875124987175, 0.8991599999999999593 ) ) ; +#28857 = FACE_OUTER_BOUND ( 'NONE', #90209, .T. ) ; +#28858 = ORIENTED_EDGE ( 'NONE', *, *, #65183, .T. ) ; +#28859 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28860 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28863 = SURFACE_STYLE_USAGE ( .BOTH. , #12462 ) ; +#28862 = SURFACE_STYLE_FILL_AREA ( #82508 ) ; +#28861 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#28864 = DIRECTION ( 'NONE', ( 0.7071072811865701802, 0.7071062811861712483, 0.000000000000000000 ) ) ; +#28865 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28866 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28867 = VECTOR ( 'NONE', #65331, 1000.000000000000000 ) ; +#28868 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28869 = CLOSED_SHELL ( 'NONE', ( #18359, #50485, #30234, #53357, #57426, #77147 ) ) ; +#28870 = EDGE_LOOP ( 'NONE', ( #44018, #25431, #67198, #87359 ) ) ; +#28872 = EDGE_CURVE ( 'NONE', #951, #52091, #45159, .T. ) ; +#28871 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40235, #397, #71360, #78024, #38707, #63733, #77503, #54035, #39205, #8479, #31554, #23921, #913, #7475, #94817, #24945, #93788, #7974, #92785 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.319567991779777166E-05, 2.576643077249112722E-05, 3.773340996187403158E-05, 4.936825240056091343E-05, 6.061772559639277676E-05, 7.172063664106871823E-05, 8.254407109509197293E-05, 9.349111382289791467E-05, 0.0001044267948011684760, 0.0001155026697639763013, 0.0001268633985065987136, 0.0001386834324107873932, 0.0001507973853380168794, 0.0001632259768666824852, 0.0001759815166969624456, 0.0001891722082235597433 ), + .UNSPECIFIED. ) ; +#28873 = AXIS2_PLACEMENT_3D ( 'NONE', #17173, #49350, #80505 ) ; +#28874 = LINE ( 'NONE', #6809, #86937 ) ; +#28875 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8648700000000000276 ) ) ; +#28876 = ADVANCED_FACE ( 'NONE', ( #92142 ), #22215, .T. ) ; +#28877 = STYLED_ITEM ( 'NONE', ( #42378 ), #100496 ) ; +#28878 = SURFACE_SIDE_STYLE ('',( #93127 ) ) ; +#28879 = CARTESIAN_POINT ( 'NONE', ( -0.08876197264234840512, -1.443664018207750033, 0.8100000000000000533 ) ) ; +#28880 = FILL_AREA_STYLE ('',( #44680 ) ) ; +#28881 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 15.40000000000000036, 0.8648700000000000276 ) ) ; +#28882 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, -11.27000000000000135 ) ) ; +#28883 = EDGE_CURVE ( 'NONE', #50880, #27880, #90680, .T. ) ; +#28884 = PLANE ( 'NONE', #66893 ) ; +#28885 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92415 ), #32182 ) ; +#28886 = SURFACE_SIDE_STYLE ('',( #74856 ) ) ; +#28887 = VECTOR ( 'NONE', #86867, 1000.000000000000000 ) ; +#28888 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28889 = FILL_AREA_STYLE_COLOUR ( '', #64736 ) ; +#28890 = LINE ( 'NONE', #44689, #35801 ) ; +#28891 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28892 = FILL_AREA_STYLE ('',( #53387 ) ) ; +#28893 = FILL_AREA_STYLE ('',( #67675 ) ) ; +#28894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33852, 'distance_accuracy_value', 'NONE'); +#28895 = LINE ( 'NONE', #35591, #38075 ) ; +#28896 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28897 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8648700000000000276 ) ) ; +#28898 = FILL_AREA_STYLE_COLOUR ( '', #96003 ) ; +#28899 = CARTESIAN_POINT ( 'NONE', ( -0.9276048691944630553, -1.263266231710209908, 0.8299999999999999600 ) ) ; +#28900 = ORIENTED_EDGE ( 'NONE', *, *, #57866, .F. ) ; +#28901 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#28902 = EDGE_CURVE ( 'NONE', #28211, #90383, #78364, .T. ) ; +#28903 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41592, 'distance_accuracy_value', 'NONE'); +#28904 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72952, 'distance_accuracy_value', 'NONE'); +#28905 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72981 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33340, #34366, #96083 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28906 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#28907 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28908 = PRESENTATION_STYLE_ASSIGNMENT (( #59093 ) ) ; +#28909 = EDGE_CURVE ( 'NONE', #81565, #94347, #92626, .T. ) ; +#28910 = VECTOR ( 'NONE', #17677, 1000.000000000000000 ) ; +#28911 = ORIENTED_EDGE ( 'NONE', *, *, #7111, .T. ) ; +#28912 = FILL_AREA_STYLE ('',( #76372 ) ) ; +#28914 = EDGE_CURVE ( 'NONE', #14207, #7099, #31382, .T. ) ; +#28913 = FILL_AREA_STYLE ('',( #92191 ) ) ; +#28915 = ORIENTED_EDGE ( 'NONE', *, *, #97603, .T. ) ; +#28916 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#28917 = LINE ( 'NONE', #37104, #3196 ) ; +#28918 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47647, 'distance_accuracy_value', 'NONE'); +#28919 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74891 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80666, #3035, #71474 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28920 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28921 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28922 = ORIENTED_EDGE ( 'NONE', *, *, #19604, .F. ) ; +#28923 = ORIENTED_EDGE ( 'NONE', *, *, #80318, .T. ) ; +#28924 = FILL_AREA_STYLE_COLOUR ( '', #16504 ) ; +#28925 = VERTEX_POINT ( 'NONE', #55904 ) ; +#28926 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#28927 = SURFACE_STYLE_USAGE ( .BOTH. , #59113 ) ; +#28928 = LINE ( 'NONE', #52941, #87547 ) ; +#28929 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#28930 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #86029, #70286 ) ; +#28931 = PRESENTATION_STYLE_ASSIGNMENT (( #91224 ) ) ; +#28934 = EDGE_LOOP ( 'NONE', ( #88390, #52694, #100415, #52143 ) ) ; +#28933 = ORIENTED_EDGE ( 'NONE', *, *, #83435, .T. ) ; +#28932 = ADVANCED_FACE ( 'NONE', ( #23236 ), #70684, .T. ) ; +#28935 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#28936 = VECTOR ( 'NONE', #88410, 1000.000000000000000 ) ; +#28937 = ORIENTED_EDGE ( 'NONE', *, *, #98005, .T. ) ; +#28938 = SURFACE_SIDE_STYLE ('',( #6400 ) ) ; +#28939 = PRESENTATION_STYLE_ASSIGNMENT (( #60133 ) ) ; +#28940 = STYLED_ITEM ( 'NONE', ( #58460 ), #41255 ) ; +#28941 = VECTOR ( 'NONE', #96077, 1000.000000000000000 ) ; +#28942 = FILL_AREA_STYLE ('',( #98804 ) ) ; +#28943 = AXIS2_PLACEMENT_3D ( 'NONE', #67333, #75508, #83684 ) ; +#28945 = CARTESIAN_POINT ( 'NONE', ( 1.380164001837510090, -0.9588323859052130249, 0.8100000000000000533 ) ) ; +#28944 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28946 = CLOSED_SHELL ( 'NONE', ( #65374, #61685, #18489, #32078, #32621, #5701 ) ) ; +#28947 = ADVANCED_FACE ( 'NONE', ( #31890 ), #800, .F. ) ; +#28948 = VECTOR ( 'NONE', #37801, 1000.000000000000000 ) ; +#28949 = SURFACE_STYLE_FILL_AREA ( #43759 ) ; +#28950 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69743 ), #2946 ) ; +#28951 = VERTEX_POINT ( 'NONE', #3266 ) ; +#28952 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38722 ) ) ; +#28953 = EDGE_CURVE ( 'NONE', #3218, #9760, #72710, .T. ) ; +#28955 = SURFACE_STYLE_USAGE ( .BOTH. , #23316 ) ; +#28954 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#28956 = ORIENTED_EDGE ( 'NONE', *, *, #26387, .T. ) ; +#28957 = EDGE_LOOP ( 'NONE', ( #5173, #91612, #50092, #10472 ) ) ; +#28958 = CARTESIAN_POINT ( 'NONE', ( 1.236552921348300194, -1.233317951191559958, 0.8100000000000000533 ) ) ; +#28959 = AXIS2_PLACEMENT_3D ( 'NONE', #36659, #28000, #28478 ) ; +#28960 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#28961 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#28962 = ADVANCED_FACE ( 'NONE', ( #11335 ), #2770, .T. ) ; +#28964 = ORIENTED_EDGE ( 'NONE', *, *, #28202, .T. ) ; +#28963 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#28965 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#28966 = FILL_AREA_STYLE_COLOUR ( '', #55153 ) ; +#28967 = VERTEX_POINT ( 'NONE', #68027 ) ; +#28968 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#28969 = FACE_OUTER_BOUND ( 'NONE', #11653, .T. ) ; +#28970 = ORIENTED_EDGE ( 'NONE', *, *, #39845, .F. ) ; +#28971 = ADVANCED_FACE ( 'NONE', ( #75712 ), #21586, .T. ) ; +#28972 = VERTEX_POINT ( 'NONE', #52755 ) ; +#28973 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#28974 = FILL_AREA_STYLE ('',( #60646 ) ) ; +#28975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70842 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62225, #60113, #57338 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#28976 = FACE_OUTER_BOUND ( 'NONE', #54586, .T. ) ; +#28977 = PRESENTATION_STYLE_ASSIGNMENT (( #36170 ) ) ; +#28978 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59996 ) ) ; +#28979 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28980 = EDGE_CURVE ( 'NONE', #35668, #20105, #74221, .T. ) ; +#28982 = ADVANCED_FACE ( 'NONE', ( #82395 ), #44063, .T. ) ; +#28981 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28983 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #64302, #71460, #72449, #17819 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#28984 = ORIENTED_EDGE ( 'NONE', *, *, #45867, .T. ) ; +#28985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#28986 = ORIENTED_EDGE ( 'NONE', *, *, #65691, .T. ) ; +#28987 = FILL_AREA_STYLE ('',( #37671 ) ) ; +#28988 = EDGE_CURVE ( 'NONE', #15215, #16362, #4269, .T. ) ; +#28989 = EDGE_CURVE ( 'NONE', #78301, #38882, #35938, .T. ) ; +#28990 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#28991 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#28992 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12597 ), #32281 ) ; +#28993 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#28994 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#28995 = LINE ( 'NONE', #5954, #46706 ) ; +#28996 = FILL_AREA_STYLE_COLOUR ( '', #21820 ) ; +#28997 = ORIENTED_EDGE ( 'NONE', *, *, #38686, .T. ) ; +#28998 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#28999 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#29000 = SURFACE_SIDE_STYLE ('',( #91767 ) ) ; +#29001 = LINE ( 'NONE', #92629, #73779 ) ; +#29002 = LINE ( 'NONE', #42337, #51694 ) ; +#29003 = VECTOR ( 'NONE', #59918, 1000.000000000000000 ) ; +#29004 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29005 = EDGE_CURVE ( 'NONE', #79954, #22278, #74723, .T. ) ; +#29006 = CARTESIAN_POINT ( 'NONE', ( 1.890937141840999924, -1.269147371132230084, 0.8100000000000000533 ) ) ; +#29007 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8648700000000000276 ) ) ; +#29008 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84466 ), #27419 ) ; +#29009 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#29010 = FACE_OUTER_BOUND ( 'NONE', #88163, .T. ) ; +#29012 = VECTOR ( 'NONE', #89426, 1000.000000000000000 ) ; +#29011 = SURFACE_SIDE_STYLE ('',( #98866 ) ) ; +#29013 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#29014 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4513 ) ) ; +#29015 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.008431457505076218537, 0.2458578643762690530 ) ) ; +#29016 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29017 = STYLED_ITEM ( 'NONE', ( #20479 ), #41591 ) ; +#29018 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29019 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84058, 'distance_accuracy_value', 'NONE'); +#29020 = ORIENTED_EDGE ( 'NONE', *, *, #12686, .F. ) ; +#29021 = VECTOR ( 'NONE', #68249, 1000.000000000000000 ) ; +#29022 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.009999999999999998473, 1.129999999999999893 ) ) ; +#29023 = LINE ( 'NONE', #68309, #17660 ) ; +#29024 = LINE ( 'NONE', #60207, #94904 ) ; +#29025 = VERTEX_POINT ( 'NONE', #53252 ) ; +#29026 = SURFACE_STYLE_FILL_AREA ( #38692 ) ; +#29027 = SURFACE_SIDE_STYLE ('',( #98881 ) ) ; +#29029 = VECTOR ( 'NONE', #38680, 1000.000000000000000 ) ; +#29028 = LINE ( 'NONE', #52030, #97129 ) ; +#29030 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#29031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53518 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79674, #9619, #64337 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29032 = SURFACE_STYLE_USAGE ( .BOTH. , #84649 ) ; +#29033 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34765, 'distance_accuracy_value', 'NONE'); +#29034 = SURFACE_STYLE_USAGE ( .BOTH. , #99382 ) ; +#29035 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #131 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20957, #75102, #11194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29036 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#29037 = CARTESIAN_POINT ( 'NONE', ( 1.407860640039253486, -1.238048172223549681, 0.8099999999998401812 ) ) ; +#29038 = FACE_OUTER_BOUND ( 'NONE', #93501, .T. ) ; +#29039 = ORIENTED_EDGE ( 'NONE', *, *, #35400, .F. ) ; +#29040 = PRESENTATION_STYLE_ASSIGNMENT (( #90312 ) ) ; +#29041 = EDGE_CURVE ( 'NONE', #61212, #16993, #40781, .T. ) ; +#29042 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29043 = FACE_OUTER_BOUND ( 'NONE', #11439, .T. ) ; +#29044 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5134 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94553, #16428, #32302 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29045 = FILL_AREA_STYLE_COLOUR ( '', #34835 ) ; +#29046 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29047 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71383, 'distance_accuracy_value', 'NONE'); +#29048 = SURFACE_STYLE_USAGE ( .BOTH. , #66348 ) ; +#29049 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29050 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97365, 'distance_accuracy_value', 'NONE'); +#29051 = SURFACE_SIDE_STYLE ('',( #28068 ) ) ; +#29052 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#29053 = EDGE_CURVE ( 'NONE', #49721, #32633, #84863, .T. ) ; +#29054 = VECTOR ( 'NONE', #42547, 1000.000000000000000 ) ; +#29055 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#29056 = FILL_AREA_STYLE ('',( #27066 ) ) ; +#29057 = ORIENTED_EDGE ( 'NONE', *, *, #46478, .T. ) ; +#29058 = ORIENTED_EDGE ( 'NONE', *, *, #59339, .T. ) ; +#29059 = AXIS2_PLACEMENT_3D ( 'NONE', #78150, #100495, #25079 ) ; +#29060 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73885, 'distance_accuracy_value', 'NONE'); +#29061 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#29062 = EDGE_LOOP ( 'NONE', ( #33644, #53674, #32117, #28311, #72524, #49855 ) ) ; +#29063 = PRESENTATION_STYLE_ASSIGNMENT (( #44840 ) ) ; +#29064 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#29065 = LINE ( 'NONE', #5036, #71139 ) ; +#29066 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29067 = SURFACE_STYLE_FILL_AREA ( #12147 ) ; +#29068 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73089 ) ) ; +#29069 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29070 = CARTESIAN_POINT ( 'NONE', ( -1.293366770995789894, -1.052467830684129968, 0.8299999999999999600 ) ) ; +#29073 = ORIENTED_EDGE ( 'NONE', *, *, #100916, .F. ) ; +#29072 = VERTEX_POINT ( 'NONE', #46030 ) ; +#29071 = ADVANCED_FACE ( 'NONE', ( #100084 ), #86396, .T. ) ; +#29074 = ORIENTED_EDGE ( 'NONE', *, *, #84777, .F. ) ; +#29075 = PLANE ( 'NONE', #73567 ) ; +#29076 = VECTOR ( 'NONE', #69028, 1000.000000000000000 ) ; +#29078 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29077 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29079 = EDGE_LOOP ( 'NONE', ( #49053, #52842, #33051, #85075 ) ) ; +#29081 = EDGE_CURVE ( 'NONE', #61391, #20259, #20276, .T. ) ; +#29080 = ORIENTED_EDGE ( 'NONE', *, *, #65088, .T. ) ; +#29082 = FILL_AREA_STYLE_COLOUR ( '', #48209 ) ; +#29083 = CARTESIAN_POINT ( 'NONE', ( 3.949527249749912095, 4.397385750250087710, 0.8648700000000000276 ) ) ; +#29084 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22585 ), #45358 ) ; +#29086 = CARTESIAN_POINT ( 'NONE', ( 3.433338875124988476, 6.695483124875013736, 0.8648700000000000276 ) ) ; +#29085 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#29087 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#29088 = EDGE_LOOP ( 'NONE', ( #88570, #77980, #35290, #52688 ) ) ; +#29089 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.000000000000000000, -0.7071067811865474617 ) ) ; +#29090 = ORIENTED_EDGE ( 'NONE', *, *, #13203, .F. ) ; +#29091 = SURFACE_STYLE_FILL_AREA ( #44375 ) ; +#29092 = SURFACE_SIDE_STYLE ('',( #99434 ) ) ; +#29093 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97561 ), #66611 ) ; +#29094 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29095 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24233 ) ) ; +#29096 = VECTOR ( 'NONE', #65157, 1000.000000000000000 ) ; +#29097 = EDGE_CURVE ( 'NONE', #34361, #43086, #15915, .T. ) ; +#29099 = EDGE_LOOP ( 'NONE', ( #30335, #10409, #17345, #86058 ) ) ; +#29098 = CARTESIAN_POINT ( 'NONE', ( 7.700000000000000178, 7.700000000000000178, 0.03429000000000000103 ) ) ; +#29100 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29102 = STYLED_ITEM ( 'NONE', ( #27836 ), #23774 ) ; +#29101 = SURFACE_STYLE_USAGE ( .BOTH. , #53591 ) ; +#29103 = ORIENTED_EDGE ( 'NONE', *, *, #88302, .T. ) ; +#29104 = SURFACE_STYLE_USAGE ( .BOTH. , #29589 ) ; +#29105 = CIRCLE ( 'NONE', #86147, 0.009999999999999998473 ) ; +#29106 = EDGE_LOOP ( 'NONE', ( #55109, #42420, #98983, #20092 ) ) ; +#29107 = ADVANCED_FACE ( 'NONE', ( #23114 ), #69537, .T. ) ; +#29108 = ORIENTED_EDGE ( 'NONE', *, *, #37996, .F. ) ; +#29109 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 10.08959499999999920, 0.8648700000000000276 ) ) ; +#29110 = LINE ( 'NONE', #37772, #75919 ) ; +#29111 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29112 = EDGE_CURVE ( 'NONE', #35029, #74888, #22091, .T. ) ; +#29114 = EDGE_CURVE ( 'NONE', #9822, #35132, #17926, .T. ) ; +#29113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61778 ), #89465 ) ; +#29115 = CARTESIAN_POINT ( 'NONE', ( 1.289721710971190038, -1.248384608377719918, 0.8299999999999997380 ) ) ; +#29116 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -3.123820061220065281, 0.000000000000000000 ) ) ; +#29117 = CARTESIAN_POINT ( 'NONE', ( 0.3533189038523930070, -0.9001815241100280529, 0.8300000000000020695 ) ) ; +#29118 = VECTOR ( 'NONE', #13451, 1000.000000000000000 ) ; +#29119 = EDGE_LOOP ( 'NONE', ( #66340, #45686, #36212, #56107 ) ) ; +#29120 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29121 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29122 = ORIENTED_EDGE ( 'NONE', *, *, #38316, .F. ) ; +#29124 = EDGE_CURVE ( 'NONE', #100631, #4524, #48103, .T. ) ; +#29123 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#29125 = EDGE_CURVE ( 'NONE', #86973, #20912, #28033, .T. ) ; +#29126 = SURFACE_SIDE_STYLE ('',( #45396 ) ) ; +#29127 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#29128 = FILL_AREA_STYLE_COLOUR ( '', #11011 ) ; +#29129 = PLANE ( 'NONE', #16544 ) ; +#29130 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29131 = CARTESIAN_POINT ( 'NONE', ( 1.766025874245259919, -1.139163918933580266, 0.8299999999999999600 ) ) ; +#29132 = SURFACE_SIDE_STYLE ('',( #28134 ) ) ; +#29133 = LINE ( 'NONE', #81398, #16912 ) ; +#29134 = EDGE_CURVE ( 'NONE', #48469, #73024, #12612, .T. ) ; +#29135 = FACE_OUTER_BOUND ( 'NONE', #21986, .T. ) ; +#29136 = EDGE_CURVE ( 'NONE', #919, #30792, #5634, .T. ) ; +#29137 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29138 = PRESENTATION_STYLE_ASSIGNMENT (( #43940 ) ) ; +#29139 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83042 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86724, #71402, #32615 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29140 = PLANE ( 'NONE', #97199 ) ; +#29141 = ADVANCED_FACE ( 'NONE', ( #56293 ), #41459, .T. ) ; +#29142 = AXIS2_PLACEMENT_3D ( 'NONE', #29516, #13616, #61687 ) ; +#29143 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#29145 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#29144 = SURFACE_STYLE_USAGE ( .BOTH. , #29621 ) ; +#29146 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29147 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29148 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32027, 'distance_accuracy_value', 'NONE'); +#29149 = VERTEX_POINT ( 'NONE', #32280 ) ; +#29150 = CARTESIAN_POINT ( 'NONE', ( -1.074341942140480066, -1.437631519369750199, 0.8100000000000000533 ) ) ; +#29151 = STYLED_ITEM ( 'NONE', ( #29920 ), #55865 ) ; +#29152 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#29153 = VECTOR ( 'NONE', #45828, 1000.000000000000000 ) ; +#29154 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#29155 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#29156 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29157 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29158 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29159 = PLANE ( 'NONE', #91522 ) ; +#29160 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29161 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29162 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40554 ), #1475 ) ; +#29163 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #938 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83412, #11851, #43574 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29164 = EDGE_LOOP ( 'NONE', ( #95353, #72900, #64404, #11647 ) ) ; +#29165 = SURFACE_SIDE_STYLE ('',( #60333 ) ) ; +#29166 = ORIENTED_EDGE ( 'NONE', *, *, #12088, .F. ) ; +#29167 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53809 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28368, #77316, #75825 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29168 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000001110, -0.004999999999999969746, -0.2399999999999999634 ) ) ; +#29169 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29170 = SURFACE_STYLE_FILL_AREA ( #44449 ) ; +#29172 = VECTOR ( 'NONE', #8856, 1000.000000000000000 ) ; +#29171 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29173 = SURFACE_SIDE_STYLE ('',( #15299 ) ) ; +#29174 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#29175 = SURFACE_STYLE_USAGE ( .BOTH. , #42978 ) ; +#29176 = ADVANCED_FACE ( 'NONE', ( #66801 ), #64930, .T. ) ; +#29177 = EDGE_LOOP ( 'NONE', ( #21762, #12391, #17904, #76928 ) ) ; +#29178 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#29179 = ORIENTED_EDGE ( 'NONE', *, *, #99414, .F. ) ; +#29180 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29181 = ORIENTED_EDGE ( 'NONE', *, *, #19995, .T. ) ; +#29182 = VECTOR ( 'NONE', #39409, 1000.000000000000114 ) ; +#29183 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.000000000000000000 ) ) ; +#29184 = STYLED_ITEM ( 'NONE', ( #632 ), #15494 ) ; +#29185 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29186 = FILL_AREA_STYLE ('',( #83319 ) ) ; +#29187 = DIRECTION ( 'NONE', ( 0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#29188 = SURFACE_STYLE_FILL_AREA ( #66476 ) ; +#29190 = ORIENTED_EDGE ( 'NONE', *, *, #75223, .F. ) ; +#29189 = VERTEX_POINT ( 'NONE', #12106 ) ; +#29192 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34724 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11615, #89812, #65843 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29191 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29193 = ORIENTED_EDGE ( 'NONE', *, *, #42153, .T. ) ; +#29194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29196 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#29195 = SURFACE_STYLE_USAGE ( .BOTH. , #99037 ) ; +#29197 = ORIENTED_EDGE ( 'NONE', *, *, #2927, .F. ) ; +#29199 = EDGE_CURVE ( 'NONE', #54210, #49432, #43325, .T. ) ; +#29198 = ORIENTED_EDGE ( 'NONE', *, *, #26248, .T. ) ; +#29200 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#29201 = SURFACE_STYLE_FILL_AREA ( #99045 ) ; +#29202 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29203 = VECTOR ( 'NONE', #54415, 1000.000000000000000 ) ; +#29204 = VECTOR ( 'NONE', #59537, 1000.000000000000000 ) ; +#29206 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8648700000000000276 ) ) ; +#29205 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29207 = ORIENTED_EDGE ( 'NONE', *, *, #67870, .F. ) ; +#29208 = VERTEX_POINT ( 'NONE', #6942 ) ; +#29209 = ORIENTED_EDGE ( 'NONE', *, *, #23199, .F. ) ; +#29210 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999993427, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#29211 = STYLED_ITEM ( 'NONE', ( #93789 ), #92644 ) ; +#29212 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12810 ) ) ; +#29214 = ORIENTED_EDGE ( 'NONE', *, *, #14191, .F. ) ; +#29213 = FILL_AREA_STYLE_COLOUR ( '', #52682 ) ; +#29215 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29216 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29217 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29218 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29219 = ORIENTED_EDGE ( 'NONE', *, *, #92804, .F. ) ; +#29220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16134 ) ) ; +#29221 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29222 = ORIENTED_EDGE ( 'NONE', *, *, #27291, .F. ) ; +#29223 = ADVANCED_FACE ( 'NONE', ( #59707 ), #98375, .T. ) ; +#29224 = VECTOR ( 'NONE', #73294, 1000.000000000000000 ) ; +#29225 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29226 = CARTESIAN_POINT ( 'NONE', ( 0.04906375505614529731, -0.9758031678253580310, 0.8299999999999988498 ) ) ; +#29227 = SURFACE_STYLE_FILL_AREA ( #6170 ) ; +#29228 = ORIENTED_EDGE ( 'NONE', *, *, #24620, .F. ) ; +#29229 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29230 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71391 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3442, #10991, #79533 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29231 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29232 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27530 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24524, #80144, #57169 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29233 = EDGE_LOOP ( 'NONE', ( #74587, #81012, #86852, #85831 ) ) ; +#29234 = VECTOR ( 'NONE', #77981, 1000.000000000000000 ) ; +#29235 = ADVANCED_FACE ( 'NONE', ( #53509 ), #67298, .T. ) ; +#29236 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4750000000000000333, -0.2458578643762690530 ) ) ; +#29237 = CARTESIAN_POINT ( 'NONE', ( 1.068409529932820012, -1.093211113524890088, 0.8300000000000022915 ) ) ; +#29238 = STYLED_ITEM ( 'NONE', ( #28600 ), #408 ) ; +#29240 = CARTESIAN_POINT ( 'NONE', ( 1.599803260885759970, -1.408946430034399899, 0.8100000000000000533 ) ) ; +#29239 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.2999999999999999889, -0.02000000000001470393 ) ) ; +#29241 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.383333333333330195, 0.000000000000000000 ) ) ; +#29242 = LINE ( 'NONE', #92014, #14072 ) ; +#29243 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29244 = SURFACE_STYLE_USAGE ( .BOTH. , #92016 ) ; +#29245 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91199 ) ) ; +#29246 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#29247 = ORIENTED_EDGE ( 'NONE', *, *, #37693, .F. ) ; +#29248 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.3000000000000020983, 0.8299999999999999600 ) ) ; +#29249 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29250 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29251 = STYLED_ITEM ( 'NONE', ( #21001 ), #15642 ) ; +#29252 = EDGE_CURVE ( 'NONE', #22953, #53705, #29991, .T. ) ; +#29253 = FILL_AREA_STYLE ('',( #52745 ) ) ; +#29254 = ORIENTED_EDGE ( 'NONE', *, *, #41440, .T. ) ; +#29255 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#29256 = FACE_OUTER_BOUND ( 'NONE', #48465, .T. ) ; +#29257 = SURFACE_STYLE_USAGE ( .BOTH. , #76708 ) ; +#29258 = SURFACE_STYLE_FILL_AREA ( #44550 ) ; +#29259 = VECTOR ( 'NONE', #85544, 1000.000000000000114 ) ; +#29260 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29261 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29262 = SURFACE_STYLE_FILL_AREA ( #8195 ) ; +#29263 = ORIENTED_EDGE ( 'NONE', *, *, #90049, .T. ) ; +#29264 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85995, #17042, #48232, #9321 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#29265 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29266 = PRESENTATION_STYLE_ASSIGNMENT (( #14895 ) ) ; +#29267 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29268 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#29269 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29270 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29271 = STYLED_ITEM ( 'NONE', ( #100119 ), #32978 ) ; +#29272 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29273 = LINE ( 'NONE', #14396, #19144 ) ; +#29274 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#29275 = VECTOR ( 'NONE', #55028, 1000.000000000000000 ) ; +#29276 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25160 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69084, #77803, #62507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29277 = EDGE_CURVE ( 'NONE', #11665, #42173, #14143, .T. ) ; +#29278 = PRESENTATION_STYLE_ASSIGNMENT (( #44565 ) ) ; +#29279 = SURFACE_SIDE_STYLE ('',( #91551 ) ) ; +#29280 = ORIENTED_EDGE ( 'NONE', *, *, #4969, .F. ) ; +#29281 = LINE ( 'NONE', #35961, #2438 ) ; +#29282 = ORIENTED_EDGE ( 'NONE', *, *, #95870, .T. ) ; +#29283 = SURFACE_STYLE_USAGE ( .BOTH. , #83904 ) ; +#29284 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58692 ) ) ; +#29285 = CARTESIAN_POINT ( 'NONE', ( 1.092224350139350264, -0.9825712221600161334, 0.8299999999999999600 ) ) ; +#29286 = LINE ( 'NONE', #44572, #65767 ) ; +#29287 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#29288 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29289 = CARTESIAN_POINT ( 'NONE', ( -0.9123894243494741207, -1.359907766992060285, 0.8299999999999981837 ) ) ; +#29290 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29291 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#29292 = FILL_AREA_STYLE_COLOUR ( '', #20716 ) ; +#29293 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29294 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_XTAL3225_20210301.STEP', ( #10893, #79511 ), #22410 ) ; +#29295 = EDGE_CURVE ( 'NONE', #39103, #94750, #90804, .T. ) ; +#29296 = ORIENTED_EDGE ( 'NONE', *, *, #91453, .T. ) ; +#29297 = SURFACE_STYLE_FILL_AREA ( #60467 ) ; +#29298 = SURFACE_STYLE_FILL_AREA ( #69573 ) ; +#29299 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01085786437626906110, 0.2500000000000000000 ) ) ; +#29300 = ORIENTED_EDGE ( 'NONE', *, *, #75907, .F. ) ; +#29301 = SURFACE_STYLE_FILL_AREA ( #5767 ) ; +#29302 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#29303 = FILL_AREA_STYLE ('',( #67090 ) ) ; +#29304 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#29305 = FACE_OUTER_BOUND ( 'NONE', #78136, .T. ) ; +#29306 = FILL_AREA_STYLE_COLOUR ( '', #82202 ) ; +#29307 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12105 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25894, #62683, #96788 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29308 = ORIENTED_EDGE ( 'NONE', *, *, #1496, .F. ) ; +#29309 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29310 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29311 = VECTOR ( 'NONE', #84995, 1000.000000000000000 ) ; +#29312 = CARTESIAN_POINT ( 'NONE', ( 1.588352962588889694, -1.042364979248349810, 0.8099999999999994982 ) ) ; +#29313 = ORIENTED_EDGE ( 'NONE', *, *, #93900, .F. ) ; +#29314 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#29315 = PRESENTATION_STYLE_ASSIGNMENT (( #69598 ) ) ; +#29316 = SURFACE_STYLE_FILL_AREA ( #46094 ) ; +#29317 = CARTESIAN_POINT ( 'NONE', ( 1.687860199445399889, -1.507611749840819915, 0.8300000000000001821 ) ) ; +#29318 = VERTEX_POINT ( 'NONE', #75975 ) ; +#29319 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29320 = EDGE_CURVE ( 'NONE', #44430, #14329, #61189, .T. ) ; +#29321 = VECTOR ( 'NONE', #1409, 1000.000000000000000 ) ; +#29322 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42397 ), #19561 ) ; +#29323 = ORIENTED_EDGE ( 'NONE', *, *, #76467, .T. ) ; +#29325 = ORIENTED_EDGE ( 'NONE', *, *, #25611, .F. ) ; +#29324 = FACE_OUTER_BOUND ( 'NONE', #10366, .T. ) ; +#29326 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73064, 'distance_accuracy_value', 'NONE'); +#29327 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29329 = CARTESIAN_POINT ( 'NONE', ( -1.352086563886500059, -1.432289833627879982, 0.8299999999999999600 ) ) ; +#29328 = SURFACE_STYLE_USAGE ( .BOTH. , #69613 ) ; +#29330 = LINE ( 'NONE', #62003, #15365 ) ; +#29331 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#29332 = ORIENTED_EDGE ( 'NONE', *, *, #55155, .T. ) ; +#29333 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29334 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29335 = ORIENTED_EDGE ( 'NONE', *, *, #46316, .T. ) ; +#29336 = EDGE_CURVE ( 'NONE', #42994, #59381, #14643, .T. ) ; +#29337 = SURFACE_STYLE_USAGE ( .BOTH. , #14964 ) ; +#29338 = EDGE_CURVE ( 'NONE', #14220, #44158, #41622, .T. ) ; +#29339 = SURFACE_SIDE_STYLE ('',( #97725 ) ) ; +#29340 = PRESENTATION_STYLE_ASSIGNMENT (( #37011 ) ) ; +#29341 = SURFACE_SIDE_STYLE ('',( #53825 ) ) ; +#29342 = EDGE_LOOP ( 'NONE', ( #85888, #14390, #48790, #77279 ) ) ; +#29343 = SURFACE_STYLE_FILL_AREA ( #84957 ) ; +#29344 = ORIENTED_EDGE ( 'NONE', *, *, #57628, .T. ) ; +#29345 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73386 ), #12936 ) ; +#29346 = VECTOR ( 'NONE', #19027, 1000.000000000000000 ) ; +#29347 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -5.551115123125790098E-17 ) ) ; +#29348 = SURFACE_STYLE_USAGE ( .BOTH. , #45132 ) ; +#29349 = LINE ( 'NONE', #66634, #57224 ) ; +#29350 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#29351 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60365 ), #84864 ) ; +#29352 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57087 ), #86424 ) ; +#29353 = ADVANCED_FACE ( 'NONE', ( #54527 ), #7944, .T. ) ; +#29354 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2654 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18019, #11306, #27249 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29355 = ORIENTED_EDGE ( 'NONE', *, *, #68197, .T. ) ; +#29356 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736763263E-18, 0.8199999999999999512, -0.04999999999999997502 ) ) ; +#29357 = EDGE_LOOP ( 'NONE', ( #57711, #92833, #54042, #26306, #20314, #28467 ) ) ; +#29359 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29358 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74007 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90425, #13760, #51663 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29361 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.1000000000000000056, -13.25000000000000000 ) ) ; +#29360 = SURFACE_SIDE_STYLE ('',( #100672 ) ) ; +#29362 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16660 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81349, #89481, #11767 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29363 = AXIS2_PLACEMENT_3D ( 'NONE', #1009, #7061, #38805 ) ; +#29364 = PRESENTATION_STYLE_ASSIGNMENT (( #29845 ) ) ; +#29365 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#29366 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#29367 = CARTESIAN_POINT ( 'NONE', ( 1.342785358116189931, -1.072184731453450057, 0.8100000000000000533 ) ) ; +#29368 = CYLINDRICAL_SURFACE ( 'NONE', #44543, 0.05000000000000012768 ) ; +#29369 = EDGE_CURVE ( 'NONE', #37756, #23828, #24909, .T. ) ; +#29370 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#29371 = VERTEX_POINT ( 'NONE', #31526 ) ; +#29372 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29373 = AXIS2_PLACEMENT_3D ( 'NONE', #7431, #69243, #94263 ) ; +#29374 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#29375 = CIRCLE ( 'NONE', #6489, 0.6500000000642103259 ) ; +#29376 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #7879 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#29377 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4192, 'distance_accuracy_value', 'NONE'); +#29378 = FILL_AREA_STYLE_COLOUR ( '', #38674 ) ; +#29379 = VECTOR ( 'NONE', #13351, 1000.000000000000000 ) ; +#29380 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29381 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29382 = FACE_OUTER_BOUND ( 'NONE', #75015, .T. ) ; +#29383 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29384 = ORIENTED_EDGE ( 'NONE', *, *, #86312, .F. ) ; +#29385 = PRESENTATION_STYLE_ASSIGNMENT (( #7316 ) ) ; +#29386 = SURFACE_STYLE_FILL_AREA ( #100208 ) ; +#29387 = AXIS2_PLACEMENT_3D ( 'NONE', #36133, #83084, #89240 ) ; +#29388 = PRESENTATION_STYLE_ASSIGNMENT (( #21714 ) ) ; +#29389 = STYLED_ITEM ( 'NONE', ( #21852 ), #51339 ) ; +#29390 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.600000000000000089, -0.2000000000000000111 ) ) ; +#29391 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29392 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#29393 = FACE_OUTER_BOUND ( 'NONE', #20514, .T. ) ; +#29394 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8648700000000000276 ) ) ; +#29395 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.000000000000000000 ) ) ; +#29396 = EDGE_CURVE ( 'NONE', #92463, #87865, #47343, .T. ) ; +#29397 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.1200000000000003147, 0.3499999999999999778 ) ) ; +#29398 = PLANE ( 'NONE', #22804 ) ; +#29399 = FILL_AREA_STYLE_COLOUR ( '', #6316 ) ; +#29400 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29401 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#29402 = VECTOR ( 'NONE', #28179, 1000.000000000000000 ) ; +#29403 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8648700000000000276 ) ) ; +#29404 = FILL_AREA_STYLE ('',( #60572 ) ) ; +#29405 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29406 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#29407 = FILL_AREA_STYLE_COLOUR ( '', #12800 ) ; +#29408 = PLANE ( 'NONE', #85084 ) ; +#29409 = ORIENTED_EDGE ( 'NONE', *, *, #95490, .T. ) ; +#29410 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29411 = FILL_AREA_STYLE ('',( #47244 ) ) ; +#29412 = PRESENTATION_STYLE_ASSIGNMENT (( #83544 ) ) ; +#29413 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3329 ) ) ; +#29414 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#29415 = EDGE_CURVE ( 'NONE', #55224, #68435, #69798, .T. ) ; +#29416 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29417 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75481, #44808, #76473, #36697 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#29418 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85046 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36029, #34533, #67134 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29419 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29420 = SURFACE_STYLE_FILL_AREA ( #36600 ) ; +#29421 = PLANE ( 'NONE', #35847 ) ; +#29423 = EDGE_CURVE ( 'NONE', #63739, #65875, #39685, .T. ) ; +#29422 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29424 = EDGE_LOOP ( 'NONE', ( #67287, #75613, #19018, #81693 ) ) ; +#29425 = LINE ( 'NONE', #15576, #88933 ) ; +#29426 = AXIS2_PLACEMENT_3D ( 'NONE', #31481, #327, #40670 ) ; +#29428 = PRESENTATION_STYLE_ASSIGNMENT (( #60593 ) ) ; +#29427 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9738 ) ) ; +#29429 = AXIS2_PLACEMENT_3D ( 'NONE', #46408, #91884, #23468 ) ; +#29430 = CARTESIAN_POINT ( 'NONE', ( -0.05311487431094850248, -1.433486393616560051, 0.8300000000000006262 ) ) ; +#29431 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29432 = ORIENTED_EDGE ( 'NONE', *, *, #33046, .F. ) ; +#29433 = ORIENTED_EDGE ( 'NONE', *, *, #90199, .T. ) ; +#29434 = AXIS2_PLACEMENT_3D ( 'NONE', #14648, #37692, #14145 ) ; +#29436 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29435 = CARTESIAN_POINT ( 'NONE', ( 0.3772639059291220121, -0.9641561732637019544, 0.8300000000000002931 ) ) ; +#29437 = VERTEX_POINT ( 'NONE', #56043 ) ; +#29438 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#29439 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 1.899999999999987255, 0.000000000000000000 ) ) ; +#29440 = CARTESIAN_POINT ( 'NONE', ( -0.8560791624706871605, 0.5647286298174479802, 0.8100000000000000533 ) ) ; +#29441 = FILL_AREA_STYLE_COLOUR ( '', #28567 ) ; +#29442 = EDGE_CURVE ( 'NONE', #18530, #14732, #1397, .T. ) ; +#29443 = LINE ( 'NONE', #14067, #57932 ) ; +#29444 = EDGE_CURVE ( 'NONE', #73267, #97466, #94284, .T. ) ; +#29445 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31043 ) ) ; +#29446 = ORIENTED_EDGE ( 'NONE', *, *, #4100, .T. ) ; +#29447 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29448 = VERTEX_POINT ( 'NONE', #48395 ) ; +#29449 = FACE_OUTER_BOUND ( 'NONE', #78437, .T. ) ; +#29450 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#29451 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16788, 'distance_accuracy_value', 'NONE'); +#29453 = PRESENTATION_STYLE_ASSIGNMENT (( #84567 ) ) ; +#29452 = FILL_AREA_STYLE_COLOUR ( '', #94837 ) ; +#29454 = SURFACE_SIDE_STYLE ('',( #76918 ) ) ; +#29455 = EDGE_CURVE ( 'NONE', #28925, #14472, #8960, .T. ) ; +#29456 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#29457 = PRESENTATION_STYLE_ASSIGNMENT (( #46236 ) ) ; +#29458 = EDGE_CURVE ( 'NONE', #56832, #19945, #71333, .T. ) ; +#29459 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#29460 = ORIENTED_EDGE ( 'NONE', *, *, #48398, .F. ) ; +#29461 = EDGE_LOOP ( 'NONE', ( #1534, #65347, #10325 ) ) ; +#29462 = ORIENTED_EDGE ( 'NONE', *, *, #47636, .F. ) ; +#29463 = STYLED_ITEM ( 'NONE', ( #93480 ), #10218 ) ; +#29464 = SURFACE_STYLE_FILL_AREA ( #51967 ) ; +#29465 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#29467 = VERTEX_POINT ( 'NONE', #77469 ) ; +#29466 = STYLED_ITEM ( 'NONE', ( #93919 ), #45101 ) ; +#29468 = PLANE ( 'NONE', #92675 ) ; +#29469 = EDGE_CURVE ( 'NONE', #62602, #14190, #37517, .T. ) ; +#29470 = LINE ( 'NONE', #91733, #36844 ) ; +#29471 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#29472 = ORIENTED_EDGE ( 'NONE', *, *, #18111, .T. ) ; +#29474 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29473 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#29475 = PLANE ( 'NONE', #96751 ) ; +#29476 = VERTEX_POINT ( 'NONE', #45607 ) ; +#29477 = VERTEX_POINT ( 'NONE', #38506 ) ; +#29478 = FILL_AREA_STYLE_COLOUR ( '', #53465 ) ; +#29479 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29480 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#29481 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29482 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29483 = CIRCLE ( 'NONE', #89825, 0.4459546481032609644 ) ; +#29484 = LINE ( 'NONE', #84109, #4215 ) ; +#29485 = SURFACE_STYLE_FILL_AREA ( #67763 ) ; +#29486 = CARTESIAN_POINT ( 'NONE', ( -0.02773322717383189945, -1.124571705400470023, 0.8299999999999999600 ) ) ; +#29487 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ESP32-S3_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ESP32-S3_20210301.STEP', '', ( #84681 ) ) ; +#29488 = CARTESIAN_POINT ( 'NONE', ( 8.383086875125043136, 2.877106875125044372, 0.8991599999999999593 ) ) ; +#29489 = SURFACE_SIDE_STYLE ('',( #61161 ) ) ; +#29490 = AXIS2_PLACEMENT_3D ( 'NONE', #66146, #97256, #27350 ) ; +#29491 = ORIENTED_EDGE ( 'NONE', *, *, #25668, .F. ) ; +#29492 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.593649167310369874, -11.91999999999999993 ) ) ; +#29493 = ORIENTED_EDGE ( 'NONE', *, *, #23068, .T. ) ; +#29494 = ADVANCED_FACE ( 'NONE', ( #76796 ), #92591, .T. ) ; +#29495 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29497 = CARTESIAN_POINT ( 'NONE', ( -0.1025235689449880000, -0.9625006208768249749, 0.8100000000000000533 ) ) ; +#29496 = VECTOR ( 'NONE', #59033, 1000.000000000000114 ) ; +#29498 = CARTESIAN_POINT ( 'NONE', ( 1.059875661710510064, -1.061634207873779934, 0.8100000000000000533 ) ) ; +#29499 = SURFACE_STYLE_FILL_AREA ( #75454 ) ; +#29500 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29501 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29502 = PRESENTATION_STYLE_ASSIGNMENT (( #37678 ) ) ; +#29503 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#29504 = FACE_OUTER_BOUND ( 'NONE', #31083, .T. ) ; +#29505 = ORIENTED_EDGE ( 'NONE', *, *, #32356, .T. ) ; +#29506 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29507 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29508 = LINE ( 'NONE', #60668, #1147 ) ; +#29509 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#29510 = CARTESIAN_POINT ( 'NONE', ( 4.232369750250087215, 4.114543249749912590, 0.8991599999999999593 ) ) ; +#29511 = SURFACE_SIDE_STYLE ('',( #99359 ) ) ; +#29512 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 2.100000000000000089, 3.495651678170121160E-76 ) ) ; +#29513 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29514 = ADVANCED_FACE ( 'NONE', ( #77294 ), #69622, .F. ) ; +#29515 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.899999999999999911, -0.02000000000003073625 ) ) ; +#29516 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#29517 = STYLED_ITEM ( 'NONE', ( #65742 ), #2297 ) ; +#29518 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.09601199999999999, 0.8648700000000000276 ) ) ; +#29519 = SURFACE_SIDE_STYLE ('',( #61691 ) ) ; +#29520 = FACE_OUTER_BOUND ( 'NONE', #28024, .T. ) ; +#29521 = PRESENTATION_STYLE_ASSIGNMENT (( #98383 ) ) ; +#29523 = EDGE_CURVE ( 'NONE', #64204, #50605, #36522, .T. ) ; +#29522 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29524 = ADVANCED_FACE ( 'NONE', ( #28828 ), #8652, .F. ) ; +#29525 = ORIENTED_EDGE ( 'NONE', *, *, #36161, .T. ) ; +#29526 = PRESENTATION_STYLE_ASSIGNMENT (( #76482 ) ) ; +#29527 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29528 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#29529 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#29530 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2499999999940882844, -4.336808749769470492E-19 ) ) ; +#29531 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29532 = EDGE_CURVE ( 'NONE', #94706, #72636, #97842, .T. ) ; +#29533 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.300000000000000044, 0.000000000000000000 ) ) ; +#29534 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000006856, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#29535 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #48091, #87889, #16904, #24121 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#29536 = AXIS2_PLACEMENT_3D ( 'NONE', #57874, #11268, #42516 ) ; +#29537 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#29538 = ORIENTED_EDGE ( 'NONE', *, *, #4182, .F. ) ; +#29539 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29540 = EDGE_CURVE ( 'NONE', #86756, #70649, #85617, .T. ) ; +#29541 = AXIS2_PLACEMENT_3D ( 'NONE', #26827, #50333, #41631 ) ; +#29542 = SURFACE_STYLE_USAGE ( .BOTH. , #37715 ) ; +#29543 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#29544 = CARTESIAN_POINT ( 'NONE', ( -3.214979999929812315E-05, -0.1350000014999999109, 0.1499999999999999667 ) ) ; +#29545 = ORIENTED_EDGE ( 'NONE', *, *, #32581, .T. ) ; +#29546 = ORIENTED_EDGE ( 'NONE', *, *, #52027, .F. ) ; +#29547 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63830 ) ) ; +#29548 = VECTOR ( 'NONE', #86958, 1000.000000000000000 ) ; +#29549 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29550 = ORIENTED_EDGE ( 'NONE', *, *, #2837, .F. ) ; +#29551 = FILL_AREA_STYLE ('',( #13664 ) ) ; +#29552 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#29553 = EDGE_CURVE ( 'NONE', #47130, #38321, #46702, .T. ) ; +#29554 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8100000000000271427 ) ) ; +#29555 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67501, #61407, #23087 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29556 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8499999999999999778, 0.000000000000000000 ) ) ; +#29557 = VECTOR ( 'NONE', #65065, 1000.000000000000000 ) ; +#29558 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #16812 ) ; +#29559 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29561 = ORIENTED_EDGE ( 'NONE', *, *, #46906, .T. ) ; +#29560 = ORIENTED_EDGE ( 'NONE', *, *, #67914, .F. ) ; +#29562 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70358 ) ) ; +#29563 = AXIS2_PLACEMENT_3D ( 'NONE', #18150, #35553, #34550 ) ; +#29564 = ORIENTED_EDGE ( 'NONE', *, *, #99091, .T. ) ; +#29565 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29383, 'distance_accuracy_value', 'NONE'); +#29566 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#29567 = ORIENTED_EDGE ( 'NONE', *, *, #85664, .F. ) ; +#29568 = ORIENTED_EDGE ( 'NONE', *, *, #99741, .F. ) ; +#29569 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.123820061220085265, 0.000000000000000000 ) ) ; +#29570 = PLANE ( 'NONE', #97827 ) ; +#29571 = EDGE_CURVE ( 'NONE', #74000, #17207, #8158, .T. ) ; +#29573 = LINE ( 'NONE', #5554, #10659 ) ; +#29572 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29574 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31183 ), #44219 ) ; +#29575 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#29576 = ORIENTED_EDGE ( 'NONE', *, *, #8677, .F. ) ; +#29577 = CARTESIAN_POINT ( 'NONE', ( -0.4682654858281209975, -1.005282756156510082, 0.8100000000000000533 ) ) ; +#29578 = ORIENTED_EDGE ( 'NONE', *, *, #70631, .T. ) ; +#29579 = VERTEX_POINT ( 'NONE', #55252 ) ; +#29580 = FILL_AREA_STYLE ('',( #83723 ) ) ; +#29581 = VECTOR ( 'NONE', #84752, 1000.000000000000000 ) ; +#29582 = AXIS2_PLACEMENT_3D ( 'NONE', #12014, #97816, #53423 ) ; +#29583 = AXIS2_PLACEMENT_3D ( 'NONE', #91607, #21670, #37008 ) ; +#29584 = ORIENTED_EDGE ( 'NONE', *, *, #73585, .T. ) ; +#29585 = FILL_AREA_STYLE_COLOUR ( '', #952 ) ; +#29586 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29587 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29588 = EDGE_LOOP ( 'NONE', ( #46557, #80719, #26683, #28358 ) ) ; +#29589 = SURFACE_SIDE_STYLE ('',( #83233 ) ) ; +#29590 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29591 = ORIENTED_EDGE ( 'NONE', *, *, #36295, .F. ) ; +#29592 = ORIENTED_EDGE ( 'NONE', *, *, #55519, .T. ) ; +#29593 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29594 = AXIS2_PLACEMENT_3D ( 'NONE', #49253, #2785, #10856 ) ; +#29595 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#29596 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#29597 = CARTESIAN_POINT ( 'NONE', ( 0.9855976085564051026, -1.097307480365639965, 0.8299999999999997380 ) ) ; +#29598 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#29599 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#29600 = ORIENTED_EDGE ( 'NONE', *, *, #24659, .T. ) ; +#29601 = CARTESIAN_POINT ( 'NONE', ( 0.4653200840722879761, -1.100151516462789969, 0.8299999999999999600 ) ) ; +#29602 = CARTESIAN_POINT ( 'NONE', ( -1.043371449138229989, -1.500691070757680157, 0.8100000000000000533 ) ) ; +#29603 = ORIENTED_EDGE ( 'NONE', *, *, #40046, .T. ) ; +#29604 = EDGE_CURVE ( 'NONE', #18237, #16986, #71041, .T. ) ; +#29605 = AXIS2_PLACEMENT_3D ( 'NONE', #23166, #77259, #76766 ) ; +#29606 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853517130, 1.377634075926972290, 0.8299999999999999600 ) ) ; +#29607 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29608 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.600000000000000089, 0.000000000000000000 ) ) ; +#29609 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.000000000000000000 ) ) ; +#29610 = LINE ( 'NONE', #60789, #48788 ) ; +#29611 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29612 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999992895, -3.149999999999990585, 0.000000000000000000 ) ) ; +#29613 = CARTESIAN_POINT ( 'NONE', ( -1.394210630085580105, -1.326636125966530244, 0.8300000000000024025 ) ) ; +#29614 = LINE ( 'NONE', #14759, #5247 ) ; +#29616 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38412, #82862, #36903 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29617 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29618 = PRESENTATION_STYLE_ASSIGNMENT (( #30599 ) ) ; +#29619 = VECTOR ( 'NONE', #90648, 1000.000000000000000 ) ; +#29620 = EDGE_CURVE ( 'NONE', #89231, #19609, #7647, .T. ) ; +#29622 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29621 = SURFACE_SIDE_STYLE ('',( #69923 ) ) ; +#29623 = VECTOR ( 'NONE', #48816, 1000.000000000000000 ) ; +#29624 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.000000000000000000 ) ) ; +#29625 = ORIENTED_EDGE ( 'NONE', *, *, #48437, .T. ) ; +#29626 = CARTESIAN_POINT ( 'NONE', ( -1.049664478641080034, -1.428972370004099934, 0.8100000000000000533 ) ) ; +#29627 = ADVANCED_FACE ( 'NONE', ( #32253 ), #63417, .T. ) ; +#29628 = AXIS2_PLACEMENT_3D ( 'NONE', #9683, #40427, #86364 ) ; +#29629 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32430, 'distance_accuracy_value', 'NONE'); +#29630 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1888, 'distance_accuracy_value', 'NONE'); +#29631 = SURFACE_SIDE_STYLE ('',( #68428 ) ) ; +#29632 = FILL_AREA_STYLE ('',( #3287 ) ) ; +#29633 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29634 = PLANE ( 'NONE', #100660 ) ; +#29635 = FILL_AREA_STYLE_COLOUR ( '', #35270 ) ; +#29636 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29637 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29638 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29639 = LINE ( 'NONE', #21984, #69200 ) ; +#29640 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#29641 = ORIENTED_EDGE ( 'NONE', *, *, #12216, .T. ) ; +#29642 = VERTEX_POINT ( 'NONE', #94996 ) ; +#29643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29644 = EDGE_CURVE ( 'NONE', #14190, #94608, #54217, .T. ) ; +#29645 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24303, 'distance_accuracy_value', 'NONE'); +#29646 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99852, 'distance_accuracy_value', 'NONE'); +#29647 = PRESENTATION_STYLE_ASSIGNMENT (( #93907 ) ) ; +#29648 = CARTESIAN_POINT ( 'NONE', ( 1.005828185112675577, -0.9557253670107159760, 0.8100000000000174838 ) ) ; +#29649 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29650 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#29651 = SURFACE_STYLE_FILL_AREA ( #52660 ) ; +#29652 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#29653 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10042 ) ) ; +#29654 = EDGE_CURVE ( 'NONE', #26314, #96973, #87365, .T. ) ; +#29655 = ORIENTED_EDGE ( 'NONE', *, *, #37577, .F. ) ; +#29656 = LINE ( 'NONE', #43981, #13958 ) ; +#29657 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29658 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29659 = VERTEX_POINT ( 'NONE', #49594 ) ; +#29660 = LINE ( 'NONE', #60843, #75185 ) ; +#29661 = FILL_AREA_STYLE_COLOUR ( '', #100471 ) ; +#29662 = ORIENTED_EDGE ( 'NONE', *, *, #100633, .F. ) ; +#29663 = FILL_AREA_STYLE_COLOUR ( '', #92538 ) ; +#29664 = EDGE_CURVE ( 'NONE', #64535, #72427, #73063, .T. ) ; +#29665 = EDGE_CURVE ( 'NONE', #39488, #67401, #57779, .T. ) ; +#29666 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29667 = LINE ( 'NONE', #37365, #36473 ) ; +#29668 = LINE ( 'NONE', #22012, #76849 ) ; +#29669 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#29671 = ORIENTED_EDGE ( 'NONE', *, *, #43665, .F. ) ; +#29670 = ORIENTED_EDGE ( 'NONE', *, *, #90173, .F. ) ; +#29672 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29673 = EDGE_CURVE ( 'NONE', #27113, #30781, #12193, .T. ) ; +#29674 = EDGE_CURVE ( 'NONE', #23190, #74052, #11676, .T. ) ; +#29675 = FILL_AREA_STYLE ('',( #76643 ) ) ; +#29676 = ORIENTED_EDGE ( 'NONE', *, *, #85655, .F. ) ; +#29677 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#29678 = ORIENTED_EDGE ( 'NONE', *, *, #83212, .T. ) ; +#29679 = ORIENTED_EDGE ( 'NONE', *, *, #71559, .F. ) ; +#29680 = PLANE ( 'NONE', #77509 ) ; +#29681 = EDGE_CURVE ( 'NONE', #64267, #70744, #42434, .T. ) ; +#29682 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32984 ), #78588 ) ; +#29683 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95928 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58617, #19780, #37987 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29684 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29685 = SURFACE_STYLE_FILL_AREA ( #99544 ) ; +#29687 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8648700000000000276 ) ) ; +#29686 = CARTESIAN_POINT ( 'NONE', ( -1.783333333333333437, -3.099999999999989875, 0.000000000000000000 ) ) ; +#29688 = ORIENTED_EDGE ( 'NONE', *, *, #60752, .F. ) ; +#29689 = ORIENTED_EDGE ( 'NONE', *, *, #28883, .F. ) ; +#29690 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#29691 = ORIENTED_EDGE ( 'NONE', *, *, #3426, .T. ) ; +#29692 = VECTOR ( 'NONE', #14492, 1000.000000000000000 ) ; +#29693 = EDGE_CURVE ( 'NONE', #72282, #88816, #39487, .T. ) ; +#29694 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36208 ) ) ; +#29695 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.266666666666659946, 3.495651678170121160E-76 ) ) ; +#29696 = AXIS2_PLACEMENT_3D ( 'NONE', #50912, #26917, #57570 ) ; +#29697 = VECTOR ( 'NONE', #55845, 1000.000000000000114 ) ; +#29698 = ORIENTED_EDGE ( 'NONE', *, *, #37921, .F. ) ; +#29699 = STYLED_ITEM ( 'NONE', ( #23361 ), #8860 ) ; +#29700 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29701 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#29702 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29703 = FILL_AREA_STYLE ('',( #60881 ) ) ; +#29704 = PRESENTATION_STYLE_ASSIGNMENT (( #45995 ) ) ; +#29705 = EDGE_LOOP ( 'NONE', ( #58155, #10890, #88477, #67853 ) ) ; +#29706 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 6.971255000000000202, 0.8648700000000000276 ) ) ; +#29707 = FACE_OUTER_BOUND ( 'NONE', #52861, .T. ) ; +#29708 = ORIENTED_EDGE ( 'NONE', *, *, #39928, .T. ) ; +#29709 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86791 ) ) ; +#29710 = CARTESIAN_POINT ( 'NONE', ( -0.1054344056808270008, -0.9001170352889870108, 0.8299999999999988498 ) ) ; +#29711 = SURFACE_SIDE_STYLE ('',( #100055 ) ) ; +#29712 = AXIS2_PLACEMENT_3D ( 'NONE', #17211, #63724, #48412 ) ; +#29713 = VERTEX_POINT ( 'NONE', #49091 ) ; +#29714 = CARTESIAN_POINT ( 'NONE', ( 1.220292586642630184, -0.8848558980161149723, 0.8299999999999998490 ) ) ; +#29715 = FILL_AREA_STYLE ('',( #99575 ) ) ; +#29717 = CARTESIAN_POINT ( 'NONE', ( 1.516559913281009919, -1.413990021526319918, 0.8100000000000000533 ) ) ; +#29716 = LINE ( 'NONE', #52718, #13753 ) ; +#29718 = PLANE ( 'NONE', #94764 ) ; +#29719 = ORIENTED_EDGE ( 'NONE', *, *, #22848, .F. ) ; +#29720 = EDGE_CURVE ( 'NONE', #16653, #27289, #83267, .T. ) ; +#29721 = VECTOR ( 'NONE', #23450, 1000.000000000000000 ) ; +#29722 = PRESENTATION_STYLE_ASSIGNMENT (( #7665 ) ) ; +#29723 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.009999999999999998473, -1.250000000000000000 ) ) ; +#29724 = EDGE_CURVE ( 'NONE', #91364, #46875, #66402, .T. ) ; +#29726 = CARTESIAN_POINT ( 'NONE', ( 1.651684746960339956, -1.440618065759700084, 0.8299999999999999600 ) ) ; +#29725 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8299999999999999600 ) ) ; +#29727 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#29728 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#29729 = AXIS2_PLACEMENT_3D ( 'NONE', #16940, #48636, #33819 ) ; +#29730 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#29731 = VERTEX_POINT ( 'NONE', #19936 ) ; +#29732 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98184 ) ) ; +#29733 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, -0.2400000000000000189 ) ) ; +#29734 = ORIENTED_EDGE ( 'NONE', *, *, #90206, .T. ) ; +#29735 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#29737 = DIRECTION ( 'NONE', ( -0.7071090539100497452, 0.7071045084557405769, 0.000000000000000000 ) ) ; +#29736 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45963 ), #37852 ) ; +#29738 = FILL_AREA_STYLE_COLOUR ( '', #100862 ) ; +#29739 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29740 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23428 ) ) ; +#29741 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6227 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97173, #49765, #89050 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29742 = ORIENTED_EDGE ( 'NONE', *, *, #36, .F. ) ; +#29743 = EDGE_CURVE ( 'NONE', #39313, #59781, #2617, .T. ) ; +#29744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29745 = SURFACE_STYLE_FILL_AREA ( #37926 ) ; +#29746 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#29747 = AXIS2_PLACEMENT_3D ( 'NONE', #7873, #33484, #93676 ) ; +#29748 = CARTESIAN_POINT ( 'NONE', ( 1.015677417745509903, -1.448219210431749948, 0.8300000000000010703 ) ) ; +#29749 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73802 ) ) ; +#29750 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#29751 = LINE ( 'NONE', #5740, #38438 ) ; +#29752 = FILL_AREA_STYLE ('',( #76728 ) ) ; +#29753 = FILL_AREA_STYLE_COLOUR ( '', #20764 ) ; +#29755 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#29754 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29756 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34696 ) ) ; +#29757 = AXIS2_PLACEMENT_3D ( 'NONE', #61457, #100115, #38456 ) ; +#29758 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81178, 'distance_accuracy_value', 'NONE'); +#29759 = ORIENTED_EDGE ( 'NONE', *, *, #1314, .T. ) ; +#29760 = SURFACE_STYLE_USAGE ( .BOTH. , #70582 ) ; +#29762 = VERTEX_POINT ( 'NONE', #33768 ) ; +#29761 = VECTOR ( 'NONE', #77166, 1000.000000000000114 ) ; +#29763 = LINE ( 'NONE', #36450, #73076 ) ; +#29764 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81849, 'distance_accuracy_value', 'NONE'); +#29765 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51161, 'distance_accuracy_value', 'NONE'); +#29766 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59207 ), #83658 ) ; +#29767 = CARTESIAN_POINT ( 'NONE', ( 1.084155851675350002, -0.9900689134305371564, 0.8299999999999999600 ) ) ; +#29768 = FILL_AREA_STYLE_COLOUR ( '', #77250 ) ; +#29769 = FACE_OUTER_BOUND ( 'NONE', #2825, .T. ) ; +#29770 = CARTESIAN_POINT ( 'NONE', ( -0.9119271331630629529, -1.344945484192040075, 0.8299999999999981837 ) ) ; +#29771 = LINE ( 'NONE', #29291, #19961 ) ; +#29772 = SURFACE_STYLE_FILL_AREA ( #99618 ) ; +#29773 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#29774 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000007994, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#29775 = ORIENTED_EDGE ( 'NONE', *, *, #12789, .T. ) ; +#29776 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29777 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12429, 'distance_accuracy_value', 'NONE'); +#29778 = SURFACE_STYLE_USAGE ( .BOTH. , #45081 ) ; +#29779 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98162 ) ) ; +#29780 = ORIENTED_EDGE ( 'NONE', *, *, #65915, .F. ) ; +#29781 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8199999999999999512 ) ) ; +#29782 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#29783 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#29784 = CARTESIAN_POINT ( 'NONE', ( -1.250988841353219971, -1.419390247362990021, 0.8100000000000000533 ) ) ; +#29785 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #887, #16173, #32038, #7453 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#29786 = SURFACE_SIDE_STYLE ('',( #37483 ) ) ; +#29787 = ORIENTED_EDGE ( 'NONE', *, *, #192, .F. ) ; +#29788 = SURFACE_STYLE_FILL_AREA ( #99635 ) ; +#29789 = FILL_AREA_STYLE ('',( #14435 ) ) ; +#29790 = ADVANCED_FACE ( 'NONE', ( #57261 ), #82241, .T. ) ; +#29791 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24146, 'distance_accuracy_value', 'NONE'); +#29792 = PRESENTATION_STYLE_ASSIGNMENT (( #83934 ) ) ; +#29793 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65674 ), #44506 ) ; +#29794 = SURFACE_STYLE_USAGE ( .BOTH. , #14440 ) ; +#29795 = VERTEX_POINT ( 'NONE', #36281 ) ; +#29796 = SURFACE_STYLE_USAGE ( .BOTH. , #28322 ) ; +#29797 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#29798 = VECTOR ( 'NONE', #37920, 1000.000000000000000 ) ; +#29799 = STYLED_ITEM ( 'NONE', ( #88680 ), #52313 ) ; +#29800 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#29801 = PRESENTATION_STYLE_ASSIGNMENT (( #27446 ) ) ; +#29802 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#29803 = ORIENTED_EDGE ( 'NONE', *, *, #18349, .F. ) ; +#29804 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#29805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37990 ), #36395 ) ; +#29806 = ADVANCED_FACE ( 'NONE', ( #60284 ), #30085, .F. ) ; +#29807 = STYLED_ITEM ( 'NONE', ( #30324 ), #75899 ) ; +#29808 = ORIENTED_EDGE ( 'NONE', *, *, #99893, .F. ) ; +#29809 = VERTEX_POINT ( 'NONE', #61283 ) ; +#29810 = LINE ( 'NONE', #54320, #36091 ) ; +#29812 = SURFACE_SIDE_STYLE ('',( #23182 ) ) ; +#29811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94965 ) ) ; +#29813 = AXIS2_PLACEMENT_3D ( 'NONE', #6591, #38324, #36316 ) ; +#29814 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01500000000000000118, 0.000000000000000000 ) ) ; +#29815 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373192999999999664, 0.8991599999999999593 ) ) ; +#29816 = ORIENTED_EDGE ( 'NONE', *, *, #86904, .F. ) ; +#29817 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.616666666666666252, 0.000000000000000000 ) ) ; +#29818 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#29819 = ORIENTED_EDGE ( 'NONE', *, *, #29664, .F. ) ; +#29820 = CARTESIAN_POINT ( 'NONE', ( -0.02257202319658345099, -1.118798891668849604, 0.8100000000000684430 ) ) ; +#29821 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766240006, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#29822 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98202 ), #13431 ) ; +#29823 = VECTOR ( 'NONE', #53248, 1000.000000000000000 ) ; +#29824 = AXIS2_PLACEMENT_3D ( 'NONE', #30471, #15139, #45790 ) ; +#29825 = ORIENTED_EDGE ( 'NONE', *, *, #71357, .T. ) ; +#29827 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#29826 = CARTESIAN_POINT ( 'NONE', ( 1.749115224440589866, -1.150470459123589695, 0.8099999999999998312 ) ) ; +#29828 = EDGE_LOOP ( 'NONE', ( #86951, #82208, #3204, #47585 ) ) ; +#29830 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82801, #13787, #21015, #12775 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#29829 = AXIS2_PLACEMENT_3D ( 'NONE', #44394, #11678, #59292 ) ; +#29831 = STYLED_ITEM ( 'NONE', ( #28655 ), #36608 ) ; +#29832 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21682 ), #78742 ) ; +#29833 = ADVANCED_FACE ( 'NONE', ( #60771 ), #38278, .T. ) ; +#29835 = CARTESIAN_POINT ( 'NONE', ( -0.1150149459265122770, 0.2193342460134301009, 0.8299999999999999600 ) ) ; +#29834 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#29836 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -3.500000000000000444, 0.000000000000000000 ) ) ; +#29837 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29838 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8299999999999999600 ) ) ; +#29839 = AXIS2_PLACEMENT_3D ( 'NONE', #84709, #40284, #960 ) ; +#29840 = ORIENTED_EDGE ( 'NONE', *, *, #98190, .F. ) ; +#29841 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.2999999999999999889, -12.64499999999999957 ) ) ; +#29842 = VERTEX_POINT ( 'NONE', #59291 ) ; +#29843 = EDGE_CURVE ( 'NONE', #34477, #5639, #28596, .T. ) ; +#29844 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29845 = SURFACE_STYLE_USAGE ( .BOTH. , #68640 ) ; +#29846 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29847 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29848 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#29849 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#29850 = LINE ( 'NONE', #14497, #25075 ) ; +#29851 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29852 = EDGE_LOOP ( 'NONE', ( #81746, #79799, #11070, #47985 ) ) ; +#29853 = AXIS2_PLACEMENT_3D ( 'NONE', #8920, #64646, #71292 ) ; +#29855 = FILL_AREA_STYLE_COLOUR ( '', #91392 ) ; +#29854 = PLANE ( 'NONE', #56160 ) ; +#29856 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#29857 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#29858 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#29859 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#29860 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65760 ) ) ; +#29861 = SHAPE_REPRESENTATION ( 'Submodel-QFN56_0P4_7_part_QFN56_0P4_7', ( #64844, #89335 ), #30617 ) ; +#29862 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#29863 = ORIENTED_EDGE ( 'NONE', *, *, #3176, .T. ) ; +#29864 = EDGE_CURVE ( 'NONE', #7626, #31980, #1723, .T. ) ; +#29865 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29866 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#29867 = LINE ( 'NONE', #39558, #790 ) ; +#29868 = CARTESIAN_POINT ( 'NONE', ( 9.514457124874956762, 4.008477124874955777, 0.8648700000000000276 ) ) ; +#29869 = FILL_AREA_STYLE_COLOUR ( '', #95802 ) ; +#29870 = PLANE ( 'NONE', #80649 ) ; +#29871 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72443, 'distance_accuracy_value', 'NONE'); +#29872 = FILL_AREA_STYLE ('',( #92158 ) ) ; +#29873 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29874 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29875 = PLANE ( 'NONE', #91910 ) ; +#29876 = SURFACE_STYLE_USAGE ( .BOTH. , #68669 ) ; +#29877 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.7000000000000009548, -0.02000000000003350487 ) ) ; +#29878 = FILL_AREA_STYLE_COLOUR ( '', #58880 ) ; +#29879 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29880 = FILL_AREA_STYLE_COLOUR ( '', #60298 ) ; +#29881 = VECTOR ( 'NONE', #43045, 1000.000000000000000 ) ; +#29882 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#29883 = DIRECTION ( 'NONE', ( -0.3376989467541748891, -0.9412541746845646262, 0.000000000000000000 ) ) ; +#29884 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#29885 = FILL_AREA_STYLE ('',( #13498 ) ) ; +#29886 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74388, 'distance_accuracy_value', 'NONE'); +#29887 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#29888 = PRESENTATION_STYLE_ASSIGNMENT (( #5868 ) ) ; +#29889 = STYLED_ITEM ( 'NONE', ( #31895 ), #19459 ) ; +#29890 = AXIS2_PLACEMENT_3D ( 'NONE', #29887, #91669, #100225 ) ; +#29891 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#29892 = FACE_OUTER_BOUND ( 'NONE', #64763, .T. ) ; +#29893 = FACE_OUTER_BOUND ( 'NONE', #6990, .T. ) ; +#29894 = ADVANCED_FACE ( 'NONE', ( #97975 ), #76060, .T. ) ; +#29895 = VERTEX_POINT ( 'NONE', #32131 ) ; +#29896 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#29897 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#29898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46673, 'distance_accuracy_value', 'NONE'); +#29900 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95172 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58503, #60489, #7251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29899 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#29901 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42955 ), #99904 ) ; +#29902 = PRESENTATION_STYLE_ASSIGNMENT (( #94183 ) ) ; +#29903 = ORIENTED_EDGE ( 'NONE', *, *, #74560, .T. ) ; +#29904 = PLANE ( 'NONE', #39328 ) ; +#29905 = VECTOR ( 'NONE', #49990, 1000.000000000000000 ) ; +#29906 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#29907 = SURFACE_SIDE_STYLE ('',( #55453 ) ) ; +#29908 = FACE_OUTER_BOUND ( 'NONE', #69816, .T. ) ; +#29909 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82139 ), #67226 ) ; +#29910 = ORIENTED_EDGE ( 'NONE', *, *, #5531, .F. ) ; +#29911 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34845 ), #78311 ) ; +#29912 = ADVANCED_FACE ( 'NONE', ( #23458 ), #30089, .F. ) ; +#29913 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47517, 'distance_accuracy_value', 'NONE'); +#29914 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29915 = VERTEX_POINT ( 'NONE', #96891 ) ; +#29916 = ORIENTED_EDGE ( 'NONE', *, *, #64877, .F. ) ; +#29917 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29918 = AXIS2_PLACEMENT_3D ( 'NONE', #94048, #22131, #69582 ) ; +#29919 = ORIENTED_EDGE ( 'NONE', *, *, #87998, .F. ) ; +#29920 = PRESENTATION_STYLE_ASSIGNMENT (( #38115 ) ) ; +#29921 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8100000000000000533 ) ) ; +#29922 = SURFACE_STYLE_FILL_AREA ( #83573 ) ; +#29923 = SURFACE_SIDE_STYLE ('',( #99298 ) ) ; +#29924 = EDGE_CURVE ( 'NONE', #16846, #72252, #11566, .T. ) ; +#29925 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#29926 = ORIENTED_EDGE ( 'NONE', *, *, #78212, .T. ) ; +#29927 = STYLED_ITEM ( 'NONE', ( #70937 ), #71318 ) ; +#29928 = VERTEX_POINT ( 'NONE', #50496 ) ; +#29929 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#29930 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#29932 = CARTESIAN_POINT ( 'NONE', ( 1.220292586642630184, -0.8848558980161149723, 0.8100000000000000533 ) ) ; +#29931 = FILL_AREA_STYLE_COLOUR ( '', #42696 ) ; +#29933 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2209 ), #44581 ) ; +#29934 = VERTEX_POINT ( 'NONE', #48968 ) ; +#29935 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#29936 = ORIENTED_EDGE ( 'NONE', *, *, #72547, .T. ) ; +#29937 = EDGE_LOOP ( 'NONE', ( #67113, #74307, #85916, #59222 ) ) ; +#29938 = CARTESIAN_POINT ( 'NONE', ( 0.9822218282947740020, -1.079235908285120171, 0.8100000000000000533 ) ) ; +#29939 = EDGE_CURVE ( 'NONE', #34637, #7028, #25492, .T. ) ; +#29940 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#29941 = STYLED_ITEM ( 'NONE', ( #37789 ), #76469 ) ; +#29942 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #18831, #67732 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #12022 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#29943 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#29944 = ORIENTED_EDGE ( 'NONE', *, *, #46633, .F. ) ; +#29945 = SURFACE_SIDE_STYLE ('',( #7402 ) ) ; +#29946 = LINE ( 'NONE', #21804, #49911 ) ; +#29947 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#29948 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#29949 = EDGE_LOOP ( 'NONE', ( #18403, #43578, #78929, #100261 ) ) ; +#29951 = SURFACE_SIDE_STYLE ('',( #52469 ) ) ; +#29950 = LINE ( 'NONE', #22308, #75931 ) ; +#29952 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#29953 = ORIENTED_EDGE ( 'NONE', *, *, #75869, .T. ) ; +#29954 = ORIENTED_EDGE ( 'NONE', *, *, #97998, .T. ) ; +#29955 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, -0.1400000000000000133 ) ) ; +#29956 = ADVANCED_FACE ( 'NONE', ( #65269 ), #49464, .F. ) ; +#29957 = CARTESIAN_POINT ( 'NONE', ( 1.157750320739350247, -1.512608977738969962, 0.8299999999999999600 ) ) ; +#29958 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#29959 = LINE ( 'NONE', #14113, #80737 ) ; +#29961 = VECTOR ( 'NONE', #14000, 1000.000000000000000 ) ; +#29960 = VECTOR ( 'NONE', #77787, 1000.000000000000000 ) ; +#29962 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21588 ) ) ; +#29963 = SURFACE_STYLE_FILL_AREA ( #83624 ) ; +#29964 = AXIS2_PLACEMENT_3D ( 'NONE', #42570, #26755, #73699 ) ; +#29965 = VECTOR ( 'NONE', #3068, 1000.000000000000000 ) ; +#29966 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31528 ) ) ; +#29967 = EDGE_LOOP ( 'NONE', ( #39839, #74815, #23817, #53186 ) ) ; +#29968 = CYLINDRICAL_SURFACE ( 'NONE', #41477, 0.009999999999999998473 ) ; +#29969 = ORIENTED_EDGE ( 'NONE', *, *, #5082, .T. ) ; +#29970 = SURFACE_STYLE_USAGE ( .BOTH. , #78974 ) ; +#29971 = CARTESIAN_POINT ( 'NONE', ( -0.02448719543550549951, -1.001398657004090254, 0.8100000000000000533 ) ) ; +#29972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41458 ), #98423 ) ; +#29973 = LINE ( 'NONE', #14628, #2757 ) ; +#29974 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2399999999999999911 ) ) ; +#29975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #785 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61518, #14479, #77303 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29976 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#29977 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#29978 = PRESENTATION_STYLE_ASSIGNMENT (( #98360 ) ) ; +#29979 = SURFACE_SIDE_STYLE ('',( #15652 ) ) ; +#29980 = SURFACE_STYLE_FILL_AREA ( #31004 ) ; +#29981 = ORIENTED_EDGE ( 'NONE', *, *, #87025, .T. ) ; +#29982 = LINE ( 'NONE', #92277, #57595 ) ; +#29983 = SURFACE_STYLE_USAGE ( .BOTH. , #68288 ) ; +#29984 = PLANE ( 'NONE', #648 ) ; +#29985 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#29986 = PLANE ( 'NONE', #94109 ) ; +#29987 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#29988 = ADVANCED_FACE ( 'NONE', ( #33132 ), #35169, .T. ) ; +#29989 = ADVANCED_FACE ( 'NONE', ( #13584 ), #75947, .T. ) ; +#29990 = FILL_AREA_STYLE_COLOUR ( '', #19736 ) ; +#29991 = LINE ( 'NONE', #44305, #70977 ) ; +#29992 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#29993 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99380 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34539, #76686, #3858 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#29994 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#29995 = FILL_AREA_STYLE_COLOUR ( '', #46947 ) ; +#29996 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3927 ) ) ; +#29997 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36336, 'distance_accuracy_value', 'NONE'); +#29998 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8099999999998640510 ) ) ; +#29999 = EDGE_CURVE ( 'NONE', #70744, #74168, #29484, .T. ) ; +#30000 = VERTEX_POINT ( 'NONE', #75444 ) ; +#30001 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30002 = PRESENTATION_STYLE_ASSIGNMENT (( #6957 ) ) ; +#30003 = DIRECTION ( 'NONE', ( -1.668003342285390072E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30004 = EDGE_CURVE ( 'NONE', #74817, #22003, #68265, .T. ) ; +#30005 = AXIS2_PLACEMENT_3D ( 'NONE', #3640, #34809, #35321 ) ; +#30007 = PLANE ( 'NONE', #21648 ) ; +#30006 = CIRCLE ( 'NONE', #87108, 0.02999999999999997113 ) ; +#30008 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62140, 'distance_accuracy_value', 'NONE'); +#30009 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30011 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74067 ) ) ; +#30010 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#30012 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30013 = VECTOR ( 'NONE', #51371, 1000.000000000000000 ) ; +#30014 = VERTEX_POINT ( 'NONE', #36668 ) ; +#30016 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74078 ) ) ; +#30015 = SURFACE_STYLE_FILL_AREA ( #68810 ) ; +#30017 = SURFACE_SIDE_STYLE ('',( #31553 ) ) ; +#30018 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#30019 = LINE ( 'NONE', #5994, #42267 ) ; +#30020 = ADVANCED_FACE ( 'NONE', ( #5449 ), #53482, .T. ) ; +#30021 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13751, 'distance_accuracy_value', 'NONE'); +#30022 = VECTOR ( 'NONE', #4129, 1000.000000000000000 ) ; +#30023 = VECTOR ( 'NONE', #34075, 1000.000000000000000 ) ; +#30024 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75269, 'distance_accuracy_value', 'NONE'); +#30025 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31724 ) ) ; +#30026 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#30027 = ORIENTED_EDGE ( 'NONE', *, *, #97072, .T. ) ; +#30028 = ADVANCED_FACE ( 'NONE', ( #28976 ), #52479, .T. ) ; +#30029 = ORIENTED_EDGE ( 'NONE', *, *, #84374, .F. ) ; +#30030 = VECTOR ( 'NONE', #95981, 1000.000000000000000 ) ; +#30031 = VECTOR ( 'NONE', #12344, 1000.000000000000000 ) ; +#30032 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.000000000000000000 ) ) ; +#30033 = VERTEX_POINT ( 'NONE', #46274 ) ; +#30034 = PRESENTATION_STYLE_ASSIGNMENT (( #54046 ) ) ; +#30035 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#30036 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30037 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#30038 = STYLED_ITEM ( 'NONE', ( #44969 ), #97518 ) ; +#30039 = EDGE_CURVE ( 'NONE', #97613, #6399, #54500, .T. ) ; +#30040 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31664 ), #73374 ) ; +#30041 = SHAPE_DEFINITION_REPRESENTATION ( #19652, #68335 ) ; +#30042 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#30043 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30044 = ADVANCED_FACE ( 'NONE', ( #53974 ), #39147, .F. ) ; +#30046 = ORIENTED_EDGE ( 'NONE', *, *, #44912, .F. ) ; +#30045 = VERTEX_POINT ( 'NONE', #7422 ) ; +#30047 = EDGE_LOOP ( 'NONE', ( #49412, #48834, #64311, #94022 ) ) ; +#30048 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30049 = EDGE_CURVE ( 'NONE', #45624, #12058, #8930, .T. ) ; +#30050 = VECTOR ( 'NONE', #91506, 1000.000000000000000 ) ; +#30051 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8648700000000000276 ) ) ; +#30052 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999580573 ) ) ; +#30053 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17008 ), #10372 ) ; +#30054 = ORIENTED_EDGE ( 'NONE', *, *, #92318, .T. ) ; +#30055 = PRODUCT_DEFINITION ( 'δ֪', '', #68166, #48403 ) ; +#30056 = ORIENTED_EDGE ( 'NONE', *, *, #89438, .T. ) ; +#30057 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#30058 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#30059 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626903161, -0.1434314575050762430 ) ) ; +#30060 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21914 ), #87159 ) ; +#30062 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#30061 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, -0.000000000000000000 ) ) ; +#30063 = CARTESIAN_POINT ( 'NONE', ( -0.5417956820186821121, -0.9001291024598061519, 0.8299999999999999600 ) ) ; +#30064 = ORIENTED_EDGE ( 'NONE', *, *, #37216, .F. ) ; +#30065 = AXIS2_PLACEMENT_3D ( 'NONE', #42041, #41052, #48196 ) ; +#30066 = ORIENTED_EDGE ( 'NONE', *, *, #97644, .F. ) ; +#30067 = ORIENTED_EDGE ( 'NONE', *, *, #1314, .F. ) ; +#30068 = EDGE_CURVE ( 'NONE', #43535, #54161, #70283, .T. ) ; +#30069 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#30071 = ORIENTED_EDGE ( 'NONE', *, *, #34678, .F. ) ; +#30070 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62020, 'distance_accuracy_value', 'NONE'); +#30072 = FILL_AREA_STYLE ('',( #15749 ) ) ; +#30073 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#30074 = VECTOR ( 'NONE', #70940, 1000.000000000000114 ) ; +#30075 = ORIENTED_EDGE ( 'NONE', *, *, #24646, .F. ) ; +#30076 = LINE ( 'NONE', #13194, #79496 ) ; +#30077 = FACE_OUTER_BOUND ( 'NONE', #41761, .T. ) ; +#30078 = ORIENTED_EDGE ( 'NONE', *, *, #78212, .F. ) ; +#30079 = EDGE_LOOP ( 'NONE', ( #24128, #34356, #17876, #12793 ) ) ; +#30080 = EDGE_CURVE ( 'NONE', #37213, #19790, #63671, .T. ) ; +#30081 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30082 = FACE_OUTER_BOUND ( 'NONE', #85600, .T. ) ; +#30083 = SURFACE_STYLE_FILL_AREA ( #91877 ) ; +#30084 = STYLED_ITEM ( 'NONE', ( #99242 ), #88802 ) ; +#30085 = CYLINDRICAL_SURFACE ( 'NONE', #13918, 0.09999999999999939493 ) ; +#30086 = EDGE_CURVE ( 'NONE', #1854, #19781, #55004, .T. ) ; +#30087 = AXIS2_PLACEMENT_3D ( 'NONE', #62514, #18010, #86994 ) ; +#30088 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#30089 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #46402, #459 ), + ( #976, #31614 ), + ( #86750, #61775 ), + ( #39262, #55129 ), + ( #85726, #47440 ), + ( #78567, #47945 ), + ( #32639, #85217 ), + ( #79102, #8533 ), + ( #94383, #9557 ), + ( #71431, #63788 ), + ( #24996, #62273 ), + ( #94871, #56130 ), + ( #69369, #15760 ), + ( #100422, #92838 ), + ( #57143, #17783 ), + ( #50988, #18794 ), + ( #89755, #41315 ), + ( #82130, #65793 ), + ( #40805, #19822 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07484053566970240434, 0.1454446621384019867, 0.2118868811787349982, 0.2753237764694380085, 0.3357631478351310039, 0.3939848020421140018, 0.4512971543544520014, 0.5078079807610630381, 0.5646647872751859865, 0.6211618527422499980, 0.6784546051597649674, 0.7377379432632189538, 0.7987761402269389910, 0.8623626670857019727, 0.9292907186512120443, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#30090 = FILL_AREA_STYLE_COLOUR ( '', #65580 ) ; +#30091 = CARTESIAN_POINT ( 'NONE', ( 1.086367759722999926, -1.195322104373920169, 0.8299999999999997380 ) ) ; +#30092 = ORIENTED_EDGE ( 'NONE', *, *, #63504, .F. ) ; +#30093 = SURFACE_STYLE_USAGE ( .BOTH. , #37784 ) ; +#30094 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999999335, 0.8991599999999999593 ) ) ; +#30095 = ORIENTED_EDGE ( 'NONE', *, *, #84383, .T. ) ; +#30096 = EDGE_CURVE ( 'NONE', #72010, #63639, #45762, .T. ) ; +#30097 = SURFACE_SIDE_STYLE ('',( #68888 ) ) ; +#30099 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59767, 'distance_accuracy_value', 'NONE'); +#30098 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30100 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#30101 = STYLED_ITEM ( 'NONE', ( #47451 ), #28227 ) ; +#30102 = VECTOR ( 'NONE', #255, 1000.000000000000227 ) ; +#30103 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30105 = VECTOR ( 'NONE', #68918, 1000.000000000000000 ) ; +#30104 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#30106 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30107 = FACE_OUTER_BOUND ( 'NONE', #26077, .T. ) ; +#30108 = FILL_AREA_STYLE_COLOUR ( '', #57809 ) ; +#30109 = AXIS2_PLACEMENT_3D ( 'NONE', #91288, #14139, #13609 ) ; +#30110 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30111 = LINE ( 'NONE', #21459, #43071 ) ; +#30112 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30113 = SURFACE_STYLE_FILL_AREA ( #99956 ) ; +#30114 = EDGE_CURVE ( 'NONE', #57512, #99398, #76956, .T. ) ; +#30115 = VECTOR ( 'NONE', #71512, 1000.000000000000000 ) ; +#30116 = LINE ( 'NONE', #93872, #61629 ) ; +#30117 = SURFACE_STYLE_USAGE ( .BOTH. , #23496 ) ; +#30118 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85593 ) ) ; +#30119 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49248, 'distance_accuracy_value', 'NONE'); +#30120 = ORIENTED_EDGE ( 'NONE', *, *, #58659, .F. ) ; +#30121 = CARTESIAN_POINT ( 'NONE', ( -1.092088612093490063, -1.441583773770549914, 0.8299999999999999600 ) ) ; +#30122 = EDGE_CURVE ( 'NONE', #62901, #99332, #18670, .T. ) ; +#30123 = FILL_AREA_STYLE ('',( #84275 ) ) ; +#30124 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30125 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30126 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18761 ) ) ; +#30127 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#30128 = LINE ( 'NONE', #61329, #78276 ) ; +#30129 = EDGE_CURVE ( 'NONE', #37284, #94750, #77958, .T. ) ; +#30130 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30131 = EDGE_LOOP ( 'NONE', ( #58640, #19839, #43508, #29568 ) ) ; +#30132 = EDGE_LOOP ( 'NONE', ( #645, #36024, #80579, #15502 ) ) ; +#30133 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, -0.01500000000000001506, -0.2399999999999999911 ) ) ; +#30134 = SURFACE_STYLE_FILL_AREA ( #47487 ) ; +#30135 = LINE ( 'NONE', #61341, #58054 ) ; +#30136 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8099999999999808464 ) ) ; +#30137 = LINE ( 'NONE', #84292, #96538 ) ; +#30138 = DIRECTION ( 'NONE', ( 0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#30139 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30140 = SURFACE_SIDE_STYLE ('',( #61345 ) ) ; +#30141 = CARTESIAN_POINT ( 'NONE', ( -0.2120937403796415155, -0.9230382407914912157, 0.8100000000003612088 ) ) ; +#30142 = CYLINDRICAL_SURFACE ( 'NONE', #10210, 0.009999999999999998473 ) ; +#30143 = ORIENTED_EDGE ( 'NONE', *, *, #655, .T. ) ; +#30144 = FILL_AREA_STYLE ('',( #38345 ) ) ; +#30145 = FILL_AREA_STYLE ('',( #23029 ) ) ; +#30146 = PLANE ( 'NONE', #99731 ) ; +#30147 = ORIENTED_EDGE ( 'NONE', *, *, #89647, .T. ) ; +#30148 = EDGE_CURVE ( 'NONE', #17103, #56597, #47997, .T. ) ; +#30149 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000020428, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#30150 = STYLED_ITEM ( 'NONE', ( #64869 ), #82417 ) ; +#30151 = STYLED_ITEM ( 'NONE', ( #13354 ), #88964 ) ; +#30152 = LINE ( 'NONE', #91460, #74536 ) ; +#30153 = ORIENTED_EDGE ( 'NONE', *, *, #99676, .F. ) ; +#30154 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4290 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79427, #71241, #55953 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30155 = AXIS2_PLACEMENT_3D ( 'NONE', #96000, #97003, #35791 ) ; +#30156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30157 = LINE ( 'NONE', #6623, #72414 ) ; +#30158 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30159 = ADVANCED_FACE ( 'NONE', ( #42562 ), #98104, .T. ) ; +#30160 = CARTESIAN_POINT ( 'NONE', ( 4.432299999999999685, 11.10741999999999940, 0.8991599999999999593 ) ) ; +#30161 = CARTESIAN_POINT ( 'NONE', ( 1.854016048130769923, -1.137681993439920047, 0.8299999999999999600 ) ) ; +#30162 = STYLED_ITEM ( 'NONE', ( #99541 ), #77153 ) ; +#30163 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8199999999999999512 ) ) ; +#30164 = ADVANCED_FACE ( 'NONE', ( #43046 ), #48359, .T. ) ; +#30166 = ORIENTED_EDGE ( 'NONE', *, *, #52728, .F. ) ; +#30165 = ORIENTED_EDGE ( 'NONE', *, *, #68125, .F. ) ; +#30167 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01085786437626904723, 0.1500000000000000222 ) ) ; +#30168 = ORIENTED_EDGE ( 'NONE', *, *, #31535, .F. ) ; +#30169 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#30170 = VECTOR ( 'NONE', #40985, 1000.000000000000000 ) ; +#30171 = VECTOR ( 'NONE', #75994, 1000.000000000000000 ) ; +#30172 = CARTESIAN_POINT ( 'NONE', ( -0.5298581286778389909, -0.9738248771264079728, 0.8299999999999999600 ) ) ; +#30173 = ORIENTED_EDGE ( 'NONE', *, *, #45720, .F. ) ; +#30174 = ORIENTED_EDGE ( 'NONE', *, *, #48949, .F. ) ; +#30177 = STYLED_ITEM ( 'NONE', ( #7420 ), #27462 ) ; +#30176 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82405 ) ) ; +#30175 = LINE ( 'NONE', #6637, #77548 ) ; +#30178 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30179 = CIRCLE ( 'NONE', #62810, 0.04999999999999991257 ) ; +#30181 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30180 = PLANE ( 'NONE', #98524 ) ; +#30182 = CARTESIAN_POINT ( 'NONE', ( 2.276179938779915091, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#30183 = VERTEX_POINT ( 'NONE', #34918 ) ; +#30184 = ORIENTED_EDGE ( 'NONE', *, *, #25307, .F. ) ; +#30185 = ORIENTED_EDGE ( 'NONE', *, *, #37682, .T. ) ; +#30186 = STYLED_ITEM ( 'NONE', ( #19199 ), #97972 ) ; +#30187 = PRESENTATION_STYLE_ASSIGNMENT (( #92466 ) ) ; +#30188 = VECTOR ( 'NONE', #29216, 1000.000000000000000 ) ; +#30190 = EDGE_LOOP ( 'NONE', ( #46463, #4589, #75157, #75689 ) ) ; +#30189 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#30191 = VECTOR ( 'NONE', #56529, 1000.000000000000000 ) ; +#30192 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30193 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30194 = EDGE_LOOP ( 'NONE', ( #13803, #31803, #62007, #36386 ) ) ; +#30195 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#30196 = ORIENTED_EDGE ( 'NONE', *, *, #26593, .F. ) ; +#30197 = EDGE_CURVE ( 'NONE', #68705, #10747, #35920, .T. ) ; +#30198 = CARTESIAN_POINT ( 'NONE', ( 0.06710731395959769474, -1.024811280222130083, 0.8299999999999988498 ) ) ; +#30199 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82311, #3671, #65973, #4667 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#30200 = EDGE_CURVE ( 'NONE', #66469, #13041, #65515, .T. ) ; +#30201 = VERTEX_POINT ( 'NONE', #97145 ) ; +#30202 = PLANE ( 'NONE', #99478 ) ; +#30203 = FACE_OUTER_BOUND ( 'NONE', #3468, .T. ) ; +#30205 = LINE ( 'NONE', #46005, #43324 ) ; +#30204 = SURFACE_STYLE_USAGE ( .BOTH. , #7653 ) ; +#30206 = CARTESIAN_POINT ( 'NONE', ( -0.9119816677340035760, -1.324294193063877856, 0.8099999999997486988 ) ) ; +#30207 = STYLED_ITEM ( 'NONE', ( #8032 ), #29912 ) ; +#30208 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30209 = SURFACE_STYLE_FILL_AREA ( #81514 ) ; +#30210 = ORIENTED_EDGE ( 'NONE', *, *, #97998, .F. ) ; +#30211 = EDGE_CURVE ( 'NONE', #51814, #5291, #27257, .T. ) ; +#30212 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8648700000000000276 ) ) ; +#30213 = PLANE ( 'NONE', #84235 ) ; +#30214 = VECTOR ( 'NONE', #27999, 1000.000000000000000 ) ; +#30215 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22067 ) ) ; +#30216 = ADVANCED_FACE ( 'NONE', ( #53727 ), #52732, .T. ) ; +#30217 = FILL_AREA_STYLE_COLOUR ( '', #77116 ) ; +#30218 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30220 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30219 = DIRECTION ( 'NONE', ( -0.7071067811865510144, 0.000000000000000000, 0.7071067811865441310 ) ) ; +#30221 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90598 ), #31933 ) ; +#30222 = FILL_AREA_STYLE_COLOUR ( '', #52607 ) ; +#30223 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30224 = ORIENTED_EDGE ( 'NONE', *, *, #85817, .T. ) ; +#30225 = VECTOR ( 'NONE', #6254, 1000.000000000000000 ) ; +#30226 = PLANE ( 'NONE', #54764 ) ; +#30227 = EDGE_CURVE ( 'NONE', #98041, #74561, #23099, .T. ) ; +#30228 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#30229 = EDGE_CURVE ( 'NONE', #96537, #37113, #85361, .T. ) ; +#30230 = ORIENTED_EDGE ( 'NONE', *, *, #21214, .T. ) ; +#30231 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4166 ), #959 ) ; +#30233 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30232 = SURFACE_STYLE_FILL_AREA ( #99102 ) ; +#30234 = ADVANCED_FACE ( 'NONE', ( #84366 ), #36905, .T. ) ; +#30235 = FILL_AREA_STYLE_COLOUR ( '', #13668 ) ; +#30236 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30237 = ORIENTED_EDGE ( 'NONE', *, *, #27930, .F. ) ; +#30238 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30240 = VECTOR ( 'NONE', #59788, 1000.000000000000000 ) ; +#30239 = FILL_AREA_STYLE_COLOUR ( '', #59676 ) ; +#30241 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.000000000000000000, 0.3499999999999999778 ) ) ; +#30242 = EDGE_CURVE ( 'NONE', #21653, #78546, #29242, .T. ) ; +#30243 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#30244 = LINE ( 'NONE', #31266, #44888 ) ; +#30245 = SURFACE_SIDE_STYLE ('',( #100582 ) ) ; +#30246 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30247 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61285 ) ) ; +#30248 = FILL_AREA_STYLE ('',( #53262 ) ) ; +#30249 = PRESENTATION_STYLE_ASSIGNMENT (( #85397 ) ) ; +#30250 = ORIENTED_EDGE ( 'NONE', *, *, #78520, .F. ) ; +#30251 = ORIENTED_EDGE ( 'NONE', *, *, #38178, .F. ) ; +#30252 = AXIS2_PLACEMENT_3D ( 'NONE', #54323, #6752, #37999 ) ; +#30253 = CARTESIAN_POINT ( 'NONE', ( 1.132978354350060224, -0.9623790331012080923, 0.8100000000000000533 ) ) ; +#30254 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#30255 = SURFACE_SIDE_STYLE ('',( #77234 ) ) ; +#30256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30257 = FILL_AREA_STYLE_COLOUR ( '', #45548 ) ; +#30258 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#30259 = CARTESIAN_POINT ( 'NONE', ( 9.818513124875011044, 9.135001124875012479, 0.8648700000000000276 ) ) ; +#30260 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30261 = VERTEX_POINT ( 'NONE', #45511 ) ; +#30262 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#30263 = SURFACE_STYLE_FILL_AREA ( #6720 ) ; +#30264 = VERTEX_POINT ( 'NONE', #7171 ) ; +#30265 = FILL_AREA_STYLE_COLOUR ( '', #10194 ) ; +#30266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30267 = PRESENTATION_STYLE_ASSIGNMENT (( #22646 ) ) ; +#30268 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30269 = DIRECTION ( 'NONE', ( -1.000000000000000000, -9.724775172514467222E-16, 0.000000000000000000 ) ) ; +#30270 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.500000000000000000, 1.869351947278245041E-79 ) ) ; +#30271 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01500000000000000118, 0.2500000000000000000 ) ) ; +#30272 = ADVANCED_FACE ( 'NONE', ( #22073 ), #37908, .F. ) ; +#30273 = ORIENTED_EDGE ( 'NONE', *, *, #4043, .T. ) ; +#30274 = PRESENTATION_STYLE_ASSIGNMENT (( #83932 ) ) ; +#30275 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42251 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63662, #95239, #48838 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30276 = VECTOR ( 'NONE', #96447, 1000.000000000000000 ) ; +#30277 = VECTOR ( 'NONE', #63812, 1000.000000000000000 ) ; +#30278 = EDGE_CURVE ( 'NONE', #42285, #85114, #29535, .T. ) ; +#30279 = AXIS2_PLACEMENT_3D ( 'NONE', #16905, #30219, #61416 ) ; +#30280 = ORIENTED_EDGE ( 'NONE', *, *, #20902, .T. ) ; +#30281 = VECTOR ( 'NONE', #50839, 1000.000000000000000 ) ; +#30282 = STYLED_ITEM ( 'NONE', ( #15281 ), #89323 ) ; +#30283 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30284 = PRESENTATION_STYLE_ASSIGNMENT (( #27840 ) ) ; +#30285 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30286 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#30287 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13389 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57132, #3497, #48462 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30288 = VERTEX_POINT ( 'NONE', #32767 ) ; +#30289 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100946 ) ; +#30290 = ORIENTED_EDGE ( 'NONE', *, *, #14417, .T. ) ; +#30291 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38164, 'distance_accuracy_value', 'NONE'); +#30292 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30293 = EDGE_CURVE ( 'NONE', #61650, #7626, #87945, .T. ) ; +#30294 = VECTOR ( 'NONE', #41333, 1000.000000000000000 ) ; +#30295 = ORIENTED_EDGE ( 'NONE', *, *, #63980, .T. ) ; +#30297 = ORIENTED_EDGE ( 'NONE', *, *, #16857, .F. ) ; +#30296 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30298 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30299 = FACE_OUTER_BOUND ( 'NONE', #81618, .T. ) ; +#30300 = SURFACE_SIDE_STYLE ('',( #14462 ) ) ; +#30301 = LINE ( 'NONE', #61503, #84659 ) ; +#30302 = ORIENTED_EDGE ( 'NONE', *, *, #65431, .F. ) ; +#30303 = SURFACE_STYLE_FILL_AREA ( #47159 ) ; +#30304 = SURFACE_STYLE_FILL_AREA ( #70128 ) ; +#30305 = CARTESIAN_POINT ( 'NONE', ( 5.257674750250088458, 8.519818750250086836, 0.8991599999999999593 ) ) ; +#30306 = VERTEX_POINT ( 'NONE', #62412 ) ; +#30307 = CARTESIAN_POINT ( 'NONE', ( 1.436760428889430008, -1.381526214478759895, 0.8299999999999999600 ) ) ; +#30308 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30309 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30310 = SURFACE_STYLE_FILL_AREA ( #52831 ) ; +#30311 = ORIENTED_EDGE ( 'NONE', *, *, #48522, .T. ) ; +#30313 = LINE ( 'NONE', #13967, #25829 ) ; +#30312 = SURFACE_STYLE_USAGE ( .BOTH. , #62013 ) ; +#30314 = ORIENTED_EDGE ( 'NONE', *, *, #18330, .F. ) ; +#30315 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63029 ), #74382 ) ; +#30316 = VECTOR ( 'NONE', #84701, 1000.000000000000114 ) ; +#30317 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30318 = LINE ( 'NONE', #62022, #36005 ) ; +#30319 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#30320 = ORIENTED_EDGE ( 'NONE', *, *, #37197, .T. ) ; +#30321 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30322 = VERTEX_POINT ( 'NONE', #15900 ) ; +#30323 = EDGE_CURVE ( 'NONE', #15767, #49941, #21044, .T. ) ; +#30325 = FILL_AREA_STYLE_COLOUR ( '', #57282 ) ; +#30324 = PRESENTATION_STYLE_ASSIGNMENT (( #7784 ) ) ; +#30326 = SURFACE_STYLE_FILL_AREA ( #67146 ) ; +#30327 = FACE_OUTER_BOUND ( 'NONE', #59896, .T. ) ; +#30328 = FILL_AREA_STYLE_COLOUR ( '', #75141 ) ; +#30329 = STYLED_ITEM ( 'NONE', ( #61296 ), #73761 ) ; +#30330 = SURFACE_SIDE_STYLE ('',( #75823 ) ) ; +#30331 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.000000000000000000 ) ) ; +#30332 = SURFACE_STYLE_USAGE ( .BOTH. , #69114 ) ; +#30333 = SURFACE_STYLE_FILL_AREA ( #67639 ) ; +#30334 = SURFACE_STYLE_FILL_AREA ( #6313 ) ; +#30335 = ORIENTED_EDGE ( 'NONE', *, *, #76636, .F. ) ; +#30336 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#30337 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56173 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71060, #39922, #63437 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30338 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30340 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65167, 'distance_accuracy_value', 'NONE'); +#30341 = LINE ( 'NONE', #92625, #95712 ) ; +#30343 = EDGE_CURVE ( 'NONE', #3215, #54974, #48612, .T. ) ; +#30342 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#30344 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#30345 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#30346 = CARTESIAN_POINT ( 'NONE', ( 5.929425999999999419, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#30347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#30348 = VERTEX_POINT ( 'NONE', #56786 ) ; +#30349 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30350 = AXIS2_PLACEMENT_3D ( 'NONE', #39811, #33161, #85748 ) ; +#30351 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#30352 = SURFACE_SIDE_STYLE ('',( #100698 ) ) ; +#30353 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17327 ) ) ; +#30354 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30355 = CARTESIAN_POINT ( 'NONE', ( 0.01549768115604830028, -1.336414498567920051, 0.8100000000000000533 ) ) ; +#30356 = EDGE_CURVE ( 'NONE', #22518, #42884, #53951, .T. ) ; +#30357 = FACE_OUTER_BOUND ( 'NONE', #8160, .T. ) ; +#30358 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71137 ), #33628 ) ; +#30359 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#30360 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30361 = FACE_OUTER_BOUND ( 'NONE', #15036, .T. ) ; +#30362 = EDGE_CURVE ( 'NONE', #63778, #41045, #10177, .T. ) ; +#30363 = FACE_OUTER_BOUND ( 'NONE', #69901, .T. ) ; +#30364 = PRESENTATION_STYLE_ASSIGNMENT (( #99252 ) ) ; +#30365 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8648700000000000276 ) ) ; +#30366 = FILL_AREA_STYLE_COLOUR ( '', #53695 ) ; +#30367 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30368 = FACE_OUTER_BOUND ( 'NONE', #70355, .T. ) ; +#30369 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#30370 = FACE_OUTER_BOUND ( 'NONE', #59641, .T. ) ; +#30371 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30372 = FILL_AREA_STYLE ('',( #45684 ) ) ; +#30373 = SURFACE_STYLE_USAGE ( .BOTH. , #7843 ) ; +#30374 = SURFACE_STYLE_FILL_AREA ( #5381 ) ; +#30375 = ORIENTED_EDGE ( 'NONE', *, *, #61248, .F. ) ; +#30376 = LINE ( 'NONE', #12496, #87819 ) ; +#30377 = SURFACE_STYLE_USAGE ( .BOTH. , #13004 ) ; +#30378 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2660 ) ) ; +#30379 = AXIS2_PLACEMENT_3D ( 'NONE', #32684, #63831, #56180 ) ; +#30380 = FILL_AREA_STYLE_COLOUR ( '', #80210 ) ; +#30381 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30382 = ORIENTED_EDGE ( 'NONE', *, *, #73525, .T. ) ; +#30383 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30384 = AXIS2_PLACEMENT_3D ( 'NONE', #73388, #72355, #95820 ) ; +#30385 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90702 ), #12414 ) ; +#30386 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, 0.000000000000000000 ) ) ; +#30387 = FILL_AREA_STYLE ('',( #53911 ) ) ; +#30388 = ORIENTED_EDGE ( 'NONE', *, *, #8264, .F. ) ; +#30389 = SURFACE_SIDE_STYLE ('',( #75882 ) ) ; +#30390 = LINE ( 'NONE', #61599, #97739 ) ; +#30391 = VECTOR ( 'NONE', #93559, 1000.000000000000000 ) ; +#30392 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76048, 'distance_accuracy_value', 'NONE'); +#30393 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999995004, 0.8200000000000000622, -0.04999999999999999584 ) ) ; +#30394 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30395 = EDGE_CURVE ( 'NONE', #85680, #31030, #41448, .T. ) ; +#30396 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#30397 = ORIENTED_EDGE ( 'NONE', *, *, #67673, .F. ) ; +#30398 = ORIENTED_EDGE ( 'NONE', *, *, #912, .T. ) ; +#30399 = FACE_OUTER_BOUND ( 'NONE', #53936, .T. ) ; +#30400 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30401 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51682 ), #84301 ) ; +#30402 = ORIENTED_EDGE ( 'NONE', *, *, #3427, .F. ) ; +#30403 = LINE ( 'NONE', #53929, #30799 ) ; +#30404 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.900000000000000577, 0.000000000000000000 ) ) ; +#30405 = FILL_AREA_STYLE_COLOUR ( '', #89225 ) ; +#30406 = FILL_AREA_STYLE ('',( #44730 ) ) ; +#30407 = ORIENTED_EDGE ( 'NONE', *, *, #99294, .T. ) ; +#30408 = ORIENTED_EDGE ( 'NONE', *, *, #90206, .F. ) ; +#30409 = CARTESIAN_POINT ( 'NONE', ( -0.8116130133853438622, 1.464409075926969894, 0.8100000000000001643 ) ) ; +#30410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67956 ), #56591 ) ; +#30411 = VECTOR ( 'NONE', #41336, 1000.000000000000114 ) ; +#30412 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60759, 'distance_accuracy_value', 'NONE'); +#30413 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.01500000000000000118, -0.2500000000000000000 ) ) ; +#30415 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30414 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30416 = ORIENTED_EDGE ( 'NONE', *, *, #32704, .F. ) ; +#30417 = AXIS2_PLACEMENT_3D ( 'NONE', #96922, #72971, #82155 ) ; +#30418 = ADVANCED_FACE ( 'NONE', ( #90 ), #31749, .T. ) ; +#30419 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30420 = VECTOR ( 'NONE', #35665, 1000.000000000000000 ) ; +#30421 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30422 = ORIENTED_EDGE ( 'NONE', *, *, #94534, .F. ) ; +#30423 = VECTOR ( 'NONE', #3855, 1000.000000000000000 ) ; +#30425 = SURFACE_STYLE_FILL_AREA ( #73432 ) ; +#30424 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30426 = ORIENTED_EDGE ( 'NONE', *, *, #59022, .F. ) ; +#30427 = VERTEX_POINT ( 'NONE', #74087 ) ; +#30428 = VECTOR ( 'NONE', #66721, 1000.000000000000000 ) ; +#30429 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#30430 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62244 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3883, #90663, #35568 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30431 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#30432 = ORIENTED_EDGE ( 'NONE', *, *, #48375, .F. ) ; +#30433 = LINE ( 'NONE', #60636, #91113 ) ; +#30434 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#30435 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15802 ), #56614 ) ; +#30436 = ORIENTED_EDGE ( 'NONE', *, *, #89273, .T. ) ; +#30438 = SURFACE_SIDE_STYLE ('',( #54486 ) ) ; +#30437 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 1.979081000000000090, 0.8648700000000000276 ) ) ; +#30439 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#30440 = ORIENTED_EDGE ( 'NONE', *, *, #91799, .F. ) ; +#30442 = ORIENTED_EDGE ( 'NONE', *, *, #62626, .F. ) ; +#30441 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #5137, #53655, #6109, #92904 ), + .UNSPECIFIED., .F., .F. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#30443 = PLANE ( 'NONE', #34021 ) ; +#30444 = ADVANCED_FACE ( 'NONE', ( #90396 ), #66420, .F. ) ; +#30446 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105604999999999727, 0.8648700000000000276 ) ) ; +#30445 = LINE ( 'NONE', #92729, #60826 ) ; +#30447 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#30448 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#30449 = AXIS2_PLACEMENT_3D ( 'NONE', #96906, #58672, #89774 ) ; +#30450 = FILL_AREA_STYLE ('',( #8416 ) ) ; +#30451 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#30452 = CARTESIAN_POINT ( 'NONE', ( -0.03333333333333900195, -3.500000000000000000, 0.000000000000000000 ) ) ; +#30453 = CARTESIAN_POINT ( 'NONE', ( -0.009862718265029700795, -1.085974092738730024, 0.8299999999999999600 ) ) ; +#30454 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92415 ) ) ; +#30455 = LINE ( 'NONE', #46276, #33006 ) ; +#30456 = VERTEX_POINT ( 'NONE', #82751 ) ; +#30457 = SURFACE_STYLE_USAGE ( .BOTH. , #68764 ) ; +#30458 = ORIENTED_EDGE ( 'NONE', *, *, #12759, .F. ) ; +#30459 = DIRECTION ( 'NONE', ( 1.000000000000000000, 4.794036587204814083E-79, 1.019578823124770065E-47 ) ) ; +#30460 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30463 = ADVANCED_FACE ( 'NONE', ( #73081 ), #14572, .F. ) ; +#30462 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30461 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30464 = FILL_AREA_STYLE_COLOUR ( '', #76388 ) ; +#30465 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30466 = LINE ( 'NONE', #1381, #9302 ) ; +#30467 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30468 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#30469 = ORIENTED_EDGE ( 'NONE', *, *, #64286, .F. ) ; +#30470 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30471 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#30472 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56686 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45705, #100253, #30394 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30473 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.000000000000000000 ) ) ; +#30474 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#30475 = SURFACE_SIDE_STYLE ('',( #14641 ) ) ; +#30476 = PRESENTATION_STYLE_ASSIGNMENT (( #61683 ) ) ; +#30477 = EDGE_CURVE ( 'NONE', #46152, #74262, #76575, .T. ) ; +#30478 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30479 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30480 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.099999999999999867, -1.195472123049164304E-89 ) ) ; +#30481 = FACE_OUTER_BOUND ( 'NONE', #78532, .T. ) ; +#30482 = FILL_AREA_STYLE_COLOUR ( '', #74659 ) ; +#30483 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30484 = AXIS2_PLACEMENT_3D ( 'NONE', #95276, #64680, #49361 ) ; +#30485 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.276179938779915091, -0.02000000000000000042 ) ) ; +#30486 = LINE ( 'NONE', #17204, #66644 ) ; +#30487 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30488 = ORIENTED_EDGE ( 'NONE', *, *, #39369, .F. ) ; +#30489 = PLANE ( 'NONE', #96699 ) ; +#30490 = SURFACE_STYLE_USAGE ( .BOTH. , #29027 ) ; +#30491 = FILL_AREA_STYLE_COLOUR ( '', #77452 ) ; +#30492 = PLANE ( 'NONE', #13409 ) ; +#30494 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30493 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68575 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32263, #48605, #79746 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30495 = CARTESIAN_POINT ( 'NONE', ( 1.265358285756654544, -1.167561955042020871, 0.8099999999998844791 ) ) ; +#30496 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30497 = CARTESIAN_POINT ( 'NONE', ( 1.702237012380340087, -1.507644428662930025, 0.8300000000000011813 ) ) ; +#30498 = FILL_AREA_STYLE_COLOUR ( '', #59780 ) ; +#30499 = ADVANCED_FACE ( 'NONE', ( #14242 ), #44904, .T. ) ; +#30501 = ORIENTED_EDGE ( 'NONE', *, *, #2117, .F. ) ; +#30500 = AXIS2_PLACEMENT_3D ( 'NONE', #8325, #62570, #9346 ) ; +#30502 = AXIS2_PLACEMENT_3D ( 'NONE', #83769, #91420, #21971 ) ; +#30503 = FILL_AREA_STYLE ('',( #86163 ) ) ; +#30504 = LINE ( 'NONE', #30018, #31525 ) ; +#30505 = STYLED_ITEM ( 'NONE', ( #30364 ), #41065 ) ; +#30506 = SURFACE_STYLE_USAGE ( .BOTH. , #92788 ) ; +#30507 = CLOSED_SHELL ( 'NONE', ( #89905, #22180, #85395, #13548, #95420, #82565 ) ) ; +#30508 = ADVANCED_FACE ( 'NONE', ( #38299 ), #91895, .T. ) ; +#30509 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.000000000000000000 ) ) ; +#30511 = CIRCLE ( 'NONE', #82754, 1.383450513437169960 ) ; +#30510 = FACE_OUTER_BOUND ( 'NONE', #9435, .T. ) ; +#30512 = ORIENTED_EDGE ( 'NONE', *, *, #91539, .F. ) ; +#30513 = ORIENTED_EDGE ( 'NONE', *, *, #27545, .F. ) ; +#30514 = VECTOR ( 'NONE', #100481, 1000.000000000000000 ) ; +#30515 = VERTEX_POINT ( 'NONE', #39799 ) ; +#30516 = FILL_AREA_STYLE ('',( #84675 ) ) ; +#30517 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79720 ) ) ; +#30518 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30519 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#30520 = CIRCLE ( 'NONE', #6012, 0.009999999999999998473 ) ; +#30521 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30522 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #10953 ) ; +#30523 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#30524 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#30526 = ORIENTED_EDGE ( 'NONE', *, *, #7295, .F. ) ; +#30525 = ORIENTED_EDGE ( 'NONE', *, *, #16895, .T. ) ; +#30527 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77370, #38586, #7357, #76889 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#30528 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43605 ), #73001 ) ; +#30529 = ORIENTED_EDGE ( 'NONE', *, *, #86084, .T. ) ; +#30530 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41952, 'distance_accuracy_value', 'NONE'); +#30532 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#30531 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.476179938779914824, -0.02000000000000000042 ) ) ; +#30533 = ORIENTED_EDGE ( 'NONE', *, *, #14490, .F. ) ; +#30534 = ORIENTED_EDGE ( 'NONE', *, *, #24499, .F. ) ; +#30535 = EDGE_CURVE ( 'NONE', #97123, #97585, #1510, .T. ) ; +#30536 = SURFACE_STYLE_USAGE ( .BOTH. , #21911 ) ; +#30537 = LINE ( 'NONE', #77538, #37321 ) ; +#30538 = AXIS2_PLACEMENT_3D ( 'NONE', #47508, #23042, #28 ) ; +#30539 = FILL_AREA_STYLE ('',( #47410 ) ) ; +#30540 = FILL_AREA_STYLE_COLOUR ( '', #26409 ) ; +#30542 = ORIENTED_EDGE ( 'NONE', *, *, #69400, .F. ) ; +#30541 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61589 ) ) ; +#30543 = CARTESIAN_POINT ( 'NONE', ( -0.4442493331421650260, -1.074915662348969958, 0.8100000000000000533 ) ) ; +#30544 = EDGE_CURVE ( 'NONE', #72098, #14832, #39276, .T. ) ; +#30545 = ORIENTED_EDGE ( 'NONE', *, *, #23995, .F. ) ; +#30546 = EDGE_CURVE ( 'NONE', #48182, #19807, #64291, .T. ) ; +#30547 = EDGE_LOOP ( 'NONE', ( #58639, #52425, #4711, #32634 ) ) ; +#30548 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#30549 = VECTOR ( 'NONE', #53498, 1000.000000000000000 ) ; +#30550 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30551 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 15.15000000000000036, 0.000000000000000000 ) ) ; +#30553 = VERTEX_POINT ( 'NONE', #8554 ) ; +#30552 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30554 = LINE ( 'NONE', #15225, #77542 ) ; +#30555 = VECTOR ( 'NONE', #94302, 1000.000000000000000 ) ; +#30556 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46196 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57421, #89051, #4277 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30558 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#30559 = ORIENTED_EDGE ( 'NONE', *, *, #2221, .F. ) ; +#30561 = CARTESIAN_POINT ( 'NONE', ( 0.01352834099273039943, -1.306448053922619978, 0.8299999999999999600 ) ) ; +#30560 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#30562 = SURFACE_STYLE_USAGE ( .BOTH. , #38271 ) ; +#30563 = VERTEX_POINT ( 'NONE', #62802 ) ; +#30564 = ORIENTED_EDGE ( 'NONE', *, *, #92383, .T. ) ; +#30565 = EDGE_CURVE ( 'NONE', #31058, #42167, #69911, .T. ) ; +#30566 = ADVANCED_FACE ( 'NONE', ( #70413 ), #55649, .F. ) ; +#30567 = SURFACE_STYLE_FILL_AREA ( #8030 ) ; +#30568 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5262 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99211, #28847, #100186 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30569 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30570 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#30571 = SURFACE_STYLE_FILL_AREA ( #68386 ) ; +#30572 = CARTESIAN_POINT ( 'NONE', ( 1.338535375846370057, -1.276477384597439979, 0.8299999999999997380 ) ) ; +#30574 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71355 ) ) ; +#30573 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35065, 'distance_accuracy_value', 'NONE'); +#30575 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#30576 = ORIENTED_EDGE ( 'NONE', *, *, #34185, .T. ) ; +#30577 = CARTESIAN_POINT ( 'NONE', ( 0.4579875826041610032, -1.125997481646370035, 0.8100000000000000533 ) ) ; +#30578 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30579 = CARTESIAN_POINT ( 'NONE', ( 0.08314493404879109983, -1.269147371132220314, 0.8299999999999999600 ) ) ; +#30580 = VERTEX_POINT ( 'NONE', #16272 ) ; +#30581 = PRESENTATION_STYLE_ASSIGNMENT (( #15772 ) ) ; +#30582 = CARTESIAN_POINT ( 'NONE', ( -0.4496349698109742832, -1.033981015936356496, 0.8299999999999999600 ) ) ; +#30583 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28940 ) ) ; +#30584 = EDGE_CURVE ( 'NONE', #90383, #91322, #478, .T. ) ; +#30586 = SURFACE_STYLE_FILL_AREA ( #15257 ) ; +#30585 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30587 = CARTESIAN_POINT ( 'NONE', ( 1.735855133396799976, -0.9683984092875530525, 0.8299999999999999600 ) ) ; +#30588 = CLOSED_SHELL ( 'NONE', ( #44377, #1570, #85198, #31454, #90704, #34096 ) ) ; +#30589 = FILL_AREA_STYLE ('',( #56151 ) ) ; +#30590 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30591 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77923 ), #4527 ) ; +#30592 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77925 ) ) ; +#30593 = LINE ( 'NONE', #45407, #99638 ) ; +#30594 = LINE ( 'NONE', #91900, #99833 ) ; +#30595 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30596 = SURFACE_STYLE_USAGE ( .BOTH. , #14253 ) ; +#30597 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30598 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #50951, #82894 ), #38598 ) ; +#30599 = SURFACE_STYLE_USAGE ( .BOTH. , #98974 ) ; +#30600 = VECTOR ( 'NONE', #70783, 1000.000000000000000 ) ; +#30601 = ADVANCED_FACE ( 'NONE', ( #24004 ), #17302, .T. ) ; +#30602 = SURFACE_STYLE_FILL_AREA ( #31639 ) ; +#30603 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74749 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93887, #17832, #70967 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30604 = EDGE_CURVE ( 'NONE', #21645, #77680, #33673, .T. ) ; +#30605 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 6.650000000000000355, 0.000000000000000000 ) ) ; +#30606 = FILL_AREA_STYLE_COLOUR ( '', #73482 ) ; +#30607 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30608 = FACE_OUTER_BOUND ( 'NONE', #77271, .T. ) ; +#30609 = STYLED_ITEM ( 'NONE', ( #45310 ), #43415 ) ; +#30610 = ORIENTED_EDGE ( 'NONE', *, *, #42682, .T. ) ; +#30611 = AXIS2_PLACEMENT_3D ( 'NONE', #95621, #56394, #16005 ) ; +#30612 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93938, 'distance_accuracy_value', 'NONE'); +#30613 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8432, 'distance_accuracy_value', 'NONE'); +#30614 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -0.9000000000000019096, 0.8299999999999999600 ) ) ; +#30615 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30616 = PRESENTATION_STYLE_ASSIGNMENT (( #17328 ) ) ; +#30617 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96423 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77140, #14808, #536 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30618 = VECTOR ( 'NONE', #100519, 1000.000000000000114 ) ; +#30619 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30620 = SURFACE_STYLE_USAGE ( .BOTH. , #70449 ) ; +#30621 = AXIS2_PLACEMENT_3D ( 'NONE', #70174, #77848, #39054 ) ; +#30622 = ADVANCED_FACE ( 'NONE', ( #87774 ), #81647, .F. ) ; +#30623 = ORIENTED_EDGE ( 'NONE', *, *, #32581, .F. ) ; +#30624 = PRESENTATION_STYLE_ASSIGNMENT (( #99500 ) ) ; +#30625 = ORIENTED_EDGE ( 'NONE', *, *, #29664, .T. ) ; +#30626 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30627 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19375, 'distance_accuracy_value', 'NONE'); +#30628 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56838, 'distance_accuracy_value', 'NONE'); +#30629 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30630 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#30631 = VECTOR ( 'NONE', #19006, 1000.000000000000000 ) ; +#30632 = FACE_OUTER_BOUND ( 'NONE', #36008, .T. ) ; +#30633 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#30634 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23922 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41122, #64588, #2808 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30635 = VECTOR ( 'NONE', #45531, 1000.000000000000000 ) ; +#30636 = CARTESIAN_POINT ( 'NONE', ( -0.1995248675705779962, -1.417598257925390293, 0.8299999999999995159 ) ) ; +#30637 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30638 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999990008, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#30639 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30640 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30641 = SURFACE_SIDE_STYLE ('',( #62847 ) ) ; +#30642 = ORIENTED_EDGE ( 'NONE', *, *, #36277, .T. ) ; +#30643 = ADVANCED_FACE ( 'NONE', ( #57165 ), #18813, .T. ) ; +#30644 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#30645 = PLANE ( 'NONE', #75433 ) ; +#30646 = EDGE_LOOP ( 'NONE', ( #79769, #55835, #69226, #67828 ) ) ; +#30647 = LINE ( 'NONE', #53664, #1797 ) ; +#30648 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#30649 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #144 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64030, #87499, #3245 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30650 = ORIENTED_EDGE ( 'NONE', *, *, #15192, .F. ) ; +#30651 = EDGE_CURVE ( 'NONE', #30306, #41413, #2783, .T. ) ; +#30652 = CARTESIAN_POINT ( 'NONE', ( 1.161760760428500072, -1.440849955440170138, 0.8299999999999999600 ) ) ; +#30653 = PRESENTATION_STYLE_ASSIGNMENT (( #71508 ) ) ; +#30654 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30655 = CARTESIAN_POINT ( 'NONE', ( 1.799202792133490103, -1.182875588085640306, 0.8299999999999999600 ) ) ; +#30656 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30657 = VECTOR ( 'NONE', #100715, 1000.000000000000000 ) ; +#30658 = EDGE_CURVE ( 'NONE', #25443, #30014, #81142, .T. ) ; +#30660 = VERTEX_POINT ( 'NONE', #80140 ) ; +#30659 = ORIENTED_EDGE ( 'NONE', *, *, #75335, .T. ) ; +#30661 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99652 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38655, #37662, #92260 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30663 = STYLED_ITEM ( 'NONE', ( #17945 ), #41455 ) ; +#30662 = FILL_AREA_STYLE ('',( #100015 ) ) ; +#30664 = VERTEX_POINT ( 'NONE', #66306 ) ; +#30665 = SURFACE_SIDE_STYLE ('',( #32215 ) ) ; +#30667 = LINE ( 'NONE', #21032, #93694 ) ; +#30666 = CARTESIAN_POINT ( 'NONE', ( 2.966666666666660124, 3.500000000000000000, 0.000000000000000000 ) ) ; +#30668 = CLOSED_SHELL ( 'NONE', ( #22602, #18488, #48309, #86134, #59937, #69425 ) ) ; +#30669 = VERTEX_POINT ( 'NONE', #97404 ) ; +#30670 = ORIENTED_EDGE ( 'NONE', *, *, #16502, .F. ) ; +#30671 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#30672 = CARTESIAN_POINT ( 'NONE', ( -0.5550755121431560912, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#30673 = FILL_AREA_STYLE_COLOUR ( '', #13580 ) ; +#30674 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30676 = FACE_OUTER_BOUND ( 'NONE', #72793, .T. ) ; +#30675 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30677 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#30679 = VERTEX_POINT ( 'NONE', #27516 ) ; +#30678 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43738 ), #9419 ) ; +#30680 = ORIENTED_EDGE ( 'NONE', *, *, #63783, .T. ) ; +#30681 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#30682 = ORIENTED_EDGE ( 'NONE', *, *, #65313, .F. ) ; +#30683 = EDGE_CURVE ( 'NONE', #28730, #80677, #76965, .T. ) ; +#30684 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63329 ), #64897 ) ; +#30685 = LINE ( 'NONE', #28698, #5210 ) ; +#30686 = AXIS2_PLACEMENT_3D ( 'NONE', #96265, #71813, #42678 ) ; +#30689 = ORIENTED_EDGE ( 'NONE', *, *, #34346, .F. ) ; +#30688 = VECTOR ( 'NONE', #24672, 1000.000000000000000 ) ; +#30687 = LINE ( 'NONE', #61879, #15074 ) ; +#30690 = LINE ( 'NONE', #38390, #88209 ) ; +#30691 = PRESENTATION_STYLE_ASSIGNMENT (( #62 ) ) ; +#30692 = ORIENTED_EDGE ( 'NONE', *, *, #28872, .F. ) ; +#30693 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30694 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#30695 = EDGE_LOOP ( 'NONE', ( #70617, #59260, #72229, #92945 ) ) ; +#30696 = ADVANCED_FACE ( 'NONE', ( #75961 ), #69251, .F. ) ; +#30697 = EDGE_CURVE ( 'NONE', #89625, #27614, #59929, .T. ) ; +#30698 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#30699 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32682 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57700, #89797, #89312 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30700 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30702 = VERTEX_POINT ( 'NONE', #74971 ) ; +#30701 = SURFACE_STYLE_USAGE ( .BOTH. , #39904 ) ; +#30703 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30705 = CARTESIAN_POINT ( 'NONE', ( 1.594774167960719913, -1.488490865982160294, 0.8100000000000000533 ) ) ; +#30704 = LINE ( 'NONE', #92968, #30050 ) ; +#30706 = CARTESIAN_POINT ( 'NONE', ( -0.9168308048384845588, -1.291309753989886788, 0.8099999999997733457 ) ) ; +#30707 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#30708 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#30709 = DIRECTION ( 'NONE', ( -1.991364888915569965E-47, 7.346839692639300209E-32, 1.000000000000000000 ) ) ; +#30710 = EDGE_LOOP ( 'NONE', ( #93458, #81112, #23317, #49964 ) ) ; +#30711 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30712 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39621 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64368, #1590, #17880 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30713 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#30714 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16696 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14921, #22636, #38464 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30715 = VECTOR ( 'NONE', #55675, 1000.000000000000000 ) ; +#30716 = ADVANCED_FACE ( 'NONE', ( #20324 ), #52004, .T. ) ; +#30717 = CARTESIAN_POINT ( 'NONE', ( 1.651684746960339956, -1.440618065759700084, 0.8100000000000000533 ) ) ; +#30718 = SURFACE_SIDE_STYLE ('',( #100554 ) ) ; +#30719 = VECTOR ( 'NONE', #82545, 1000.000000000000000 ) ; +#30720 = SURFACE_SIDE_STYLE ('',( #38414 ) ) ; +#30721 = EDGE_CURVE ( 'NONE', #44005, #27175, #45283, .T. ) ; +#30722 = SURFACE_SIDE_STYLE ('',( #38416 ) ) ; +#30723 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61749 ) ) ; +#30724 = FILL_AREA_STYLE ('',( #84370 ) ) ; +#30725 = ORIENTED_EDGE ( 'NONE', *, *, #70238, .F. ) ; +#30726 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30727 = STYLED_ITEM ( 'NONE', ( #80116 ), #17749 ) ; +#30728 = ORIENTED_EDGE ( 'NONE', *, *, #19549, .F. ) ; +#30729 = EDGE_CURVE ( 'NONE', #25700, #538, #68773, .T. ) ; +#30730 = FACE_OUTER_BOUND ( 'NONE', #44374, .T. ) ; +#30731 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69875 ), #65027 ) ; +#30732 = EDGE_CURVE ( 'NONE', #50605, #83432, #22332, .T. ) ; +#30734 = LINE ( 'NONE', #15404, #83645 ) ; +#30733 = PRESENTATION_STYLE_ASSIGNMENT (( #68023 ) ) ; +#30735 = SURFACE_STYLE_FILL_AREA ( #1648 ) ; +#30736 = VECTOR ( 'NONE', #76315, 1000.000000000000000 ) ; +#30737 = AXIS2_PLACEMENT_3D ( 'NONE', #22762, #68691, #62093 ) ; +#30738 = PLANE ( 'NONE', #78709 ) ; +#30739 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30740 = ORIENTED_EDGE ( 'NONE', *, *, #70631, .F. ) ; +#30741 = CARTESIAN_POINT ( 'NONE', ( 1.714851922897540071, -0.9003478538782040408, 0.8100000000000008304 ) ) ; +#30742 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#30743 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30744 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8991599999999999593 ) ) ; +#30745 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#30746 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30747 = PRESENTATION_STYLE_ASSIGNMENT (( #39427 ) ) ; +#30748 = PRESENTATION_STYLE_ASSIGNMENT (( #100581 ) ) ; +#30749 = STYLED_ITEM ( 'NONE', ( #60659 ), #50684 ) ; +#30750 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30751 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.523820061220085176, 0.000000000000000000 ) ) ; +#30752 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79187, 'distance_accuracy_value', 'NONE'); +#30753 = VECTOR ( 'NONE', #7956, 1000.000000000000000 ) ; +#30754 = SURFACE_STYLE_FILL_AREA ( #61447 ) ; +#30755 = VECTOR ( 'NONE', #44161, 1000.000000000000000 ) ; +#30756 = ADVANCED_FACE ( 'NONE', ( #45783 ), #51518, .T. ) ; +#30757 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#30758 = VERTEX_POINT ( 'NONE', #47328 ) ; +#30759 = VERTEX_POINT ( 'NONE', #70812 ) ; +#30760 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, 0.000000000000000000 ) ) ; +#30761 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77191, 'distance_accuracy_value', 'NONE'); +#30762 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9285, 'distance_accuracy_value', 'NONE'); +#30763 = VECTOR ( 'NONE', #81186, 1000.000000000000000 ) ; +#30764 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8299999999999999600 ) ) ; +#30765 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30766 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#30767 = SURFACE_STYLE_USAGE ( .BOTH. , #23141 ) ; +#30768 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 0.4242640687119280107 ) ) ; +#30769 = FILL_AREA_STYLE ('',( #67076 ) ) ; +#30770 = FILL_AREA_STYLE_COLOUR ( '', #30451 ) ; +#30771 = ORIENTED_EDGE ( 'NONE', *, *, #81838, .F. ) ; +#30772 = EDGE_CURVE ( 'NONE', #86105, #73310, #31002, .T. ) ; +#30773 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30774 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97637, 'distance_accuracy_value', 'NONE'); +#30775 = SURFACE_STYLE_FILL_AREA ( #14922 ) ; +#30776 = ORIENTED_EDGE ( 'NONE', *, *, #3060, .F. ) ; +#30777 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30778 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#30779 = AXIS2_PLACEMENT_3D ( 'NONE', #74871, #98271, #75368 ) ; +#30780 = VECTOR ( 'NONE', #34141, 1000.000000000000000 ) ; +#30781 = VERTEX_POINT ( 'NONE', #24895 ) ; +#30782 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.300000000000000266, 8.972889346935576195E-79 ) ) ; +#30783 = EDGE_CURVE ( 'NONE', #19290, #48036, #863, .T. ) ; +#30784 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#30785 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22647 ), #68240 ) ; +#30786 = VECTOR ( 'NONE', #67304, 1000.000000000000000 ) ; +#30787 = SURFACE_STYLE_FILL_AREA ( #56716 ) ; +#30788 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999990452, -0.02000000000000000042 ) ) ; +#30789 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#30790 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#30791 = EDGE_CURVE ( 'NONE', #61609, #17384, #86643, .T. ) ; +#30792 = VERTEX_POINT ( 'NONE', #16154 ) ; +#30793 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74833 ), #22718 ) ; +#30794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81805, 'distance_accuracy_value', 'NONE'); +#30795 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#30797 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#30796 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3128 ) ) ; +#30798 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#30799 = VECTOR ( 'NONE', #69724, 1000.000000000000000 ) ; +#30800 = EDGE_LOOP ( 'NONE', ( #22665, #60278, #27783, #1564 ) ) ; +#30801 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40209 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75033, #36232, #12660 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30802 = SURFACE_SIDE_STYLE ('',( #53799 ) ) ; +#30803 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#30804 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#30805 = SURFACE_SIDE_STYLE ('',( #171 ) ) ; +#30806 = LINE ( 'NONE', #54310, #34608 ) ; +#30807 = EDGE_LOOP ( 'NONE', ( #30670, #27656, #99095, #95296, #47101, #77044 ) ) ; +#30808 = ORIENTED_EDGE ( 'NONE', *, *, #66854, .F. ) ; +#30809 = SURFACE_STYLE_USAGE ( .BOTH. , #100630 ) ; +#30810 = EDGE_CURVE ( 'NONE', #44510, #2199, #71321, .T. ) ; +#30811 = ORIENTED_EDGE ( 'NONE', *, *, #59275, .T. ) ; +#30812 = EDGE_CURVE ( 'NONE', #59781, #47416, #94269, .T. ) ; +#30813 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68271 ), #21316 ) ; +#30814 = VECTOR ( 'NONE', #94810, 1000.000000000000000 ) ; +#30815 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#30816 = EDGE_LOOP ( 'NONE', ( #2557, #47447, #27539, #31684 ) ) ; +#30818 = EDGE_LOOP ( 'NONE', ( #84347, #43782, #86496, #13948 ) ) ; +#30817 = FILL_AREA_STYLE ('',( #77796 ) ) ; +#30819 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45938 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49276, #1806, #95690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#30820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30822 = FILL_AREA_STYLE_COLOUR ( '', #100136 ) ; +#30821 = SURFACE_STYLE_FILL_AREA ( #38497 ) ; +#30823 = LINE ( 'NONE', #60505, #88808 ) ; +#30824 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30825 = VECTOR ( 'NONE', #96511, 1000.000000000000114 ) ; +#30826 = ORIENTED_EDGE ( 'NONE', *, *, #97472, .T. ) ; +#30827 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30828 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2891, #71313, #2387, #42201, #64167, #32532, #63678, #56536, #91155, #75327, #42688, #83503, #90657, #73834, #52372, #59051, #27374 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.705228468942276685E-05, 5.458052432788891632E-05, 6.831271144852316048E-05, 8.155876993717794520E-05, 9.439864586049832916E-05, 0.0001069200678181017063, 0.0001193470454069902958, 0.0001314581719509139710, 0.0001436029006962671070, 0.0001558018078443691528, 0.0001685983300954972154, 0.0001819180217514449805, 0.0001963884671246555569, 0.0002119936637375495697 ), + .UNSPECIFIED. ) ; +#30829 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#30830 = EDGE_LOOP ( 'NONE', ( #86986, #11738, #39970, #31318 ) ) ; +#30831 = CARTESIAN_POINT ( 'NONE', ( 0.4645119866146585341, 0.3274465759269651888, 0.8100000000000000533 ) ) ; +#30832 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#30833 = EDGE_CURVE ( 'NONE', #31444, #71668, #7437, .T. ) ; +#30834 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30835 = LINE ( 'NONE', #39507, #25463 ) ; +#30836 = ORIENTED_EDGE ( 'NONE', *, *, #60123, .T. ) ; +#30838 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8648700000000000276 ) ) ; +#30837 = LINE ( 'NONE', #38014, #42115 ) ; +#30839 = ORIENTED_EDGE ( 'NONE', *, *, #89116, .T. ) ; +#30840 = EDGE_CURVE ( 'NONE', #63028, #45362, #53989, .T. ) ; +#30842 = CARTESIAN_POINT ( 'NONE', ( 1.658992833246659915, -1.164662551751850073, 0.8100000000000000533 ) ) ; +#30841 = LINE ( 'NONE', #45129, #8692 ) ; +#30843 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#30844 = VERTEX_POINT ( 'NONE', #40702 ) ; +#30845 = SURFACE_STYLE_USAGE ( .BOTH. , #100667 ) ; +#30846 = VERTEX_POINT ( 'NONE', #77975 ) ; +#30847 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373192999999999664, 0.8991599999999999593 ) ) ; +#30848 = FACE_OUTER_BOUND ( 'NONE', #35855, .T. ) ; +#30849 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.600000000000000089, 0.000000000000000000 ) ) ; +#30850 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37073, 'distance_accuracy_value', 'NONE'); +#30851 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#30852 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74904 ), #96075 ) ; +#30853 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30854 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30855 = PLANE ( 'NONE', #62310 ) ; +#30856 = SURFACE_STYLE_USAGE ( .BOTH. , #79355 ) ; +#30857 = CYLINDRICAL_SURFACE ( 'NONE', #23485, 0.05000000000000002359 ) ; +#30858 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.000000000000000000 ) ) ; +#30859 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#30860 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30861 = ORIENTED_EDGE ( 'NONE', *, *, #10812, .F. ) ; +#30862 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#30863 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.899999999999999911, 0.000000000000000000 ) ) ; +#30864 = EDGE_CURVE ( 'NONE', #91206, #67465, #79501, .T. ) ; +#30865 = CARTESIAN_POINT ( 'NONE', ( -3.519999999999989804, -7.594371560187019297E-15, 0.000000000000000000 ) ) ; +#30866 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30867 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58692 ), #16197 ) ; +#30868 = LINE ( 'NONE', #1777, #12586 ) ; +#30869 = CARTESIAN_POINT ( 'NONE', ( 2.616666666666666252, -3.099999999999960121, 0.000000000000000000 ) ) ; +#30870 = CARTESIAN_POINT ( 'NONE', ( -1.316686852848500067, -1.306787212278190058, 0.8299999999999998490 ) ) ; +#30871 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30872 = EDGE_CURVE ( 'NONE', #92376, #2363, #78982, .T. ) ; +#30873 = AXIS2_PLACEMENT_3D ( 'NONE', #97782, #43202, #81557 ) ; +#30874 = SURFACE_STYLE_FILL_AREA ( #45660 ) ; +#30875 = ORIENTED_EDGE ( 'NONE', *, *, #47279, .F. ) ; +#30876 = SURFACE_SIDE_STYLE ('',( #15007 ) ) ; +#30877 = AXIS2_PLACEMENT_3D ( 'NONE', #9993, #33597, #18737 ) ; +#30878 = SURFACE_STYLE_USAGE ( .BOTH. , #100697 ) ; +#30879 = PLANE ( 'NONE', #66901 ) ; +#30880 = CARTESIAN_POINT ( 'NONE', ( -0.05311487431094850248, -1.433486393616560051, 0.8100000000000000533 ) ) ; +#30881 = PLANE ( 'NONE', #38754 ) ; +#30882 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000000222, -3.123820061220075051, 0.000000000000000000 ) ) ; +#30883 = VECTOR ( 'NONE', #75230, 1000.000000000000000 ) ; +#30884 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#30885 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.266666666666647068, 0.000000000000000000 ) ) ; +#30886 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30887 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#30888 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30889 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#30890 = SURFACE_STYLE_FILL_AREA ( #16555 ) ; +#30891 = EDGE_CURVE ( 'NONE', #95335, #47306, #30466, .T. ) ; +#30892 = SURFACE_STYLE_FILL_AREA ( #93645 ) ; +#30893 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92802 ), #96110 ) ; +#30894 = PLANE ( 'NONE', #57871 ) ; +#30895 = VERTEX_POINT ( 'NONE', #63682 ) ; +#30896 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21865, 'distance_accuracy_value', 'NONE'); +#30897 = STYLED_ITEM ( 'NONE', ( #73846 ), #42578 ) ; +#30898 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999667, -4.513898307157582662E-33 ) ) ; +#30899 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8099999999999442091 ) ) ; +#30900 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73656, 'distance_accuracy_value', 'NONE'); +#30901 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30902 = SURFACE_STYLE_FILL_AREA ( #44696 ) ; +#30903 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30904 = AXIS2_PLACEMENT_3D ( 'NONE', #40807, #57149, #79614 ) ; +#30905 = FILL_AREA_STYLE ('',( #69693 ) ) ; +#30906 = ORIENTED_EDGE ( 'NONE', *, *, #93599, .F. ) ; +#30907 = LINE ( 'NONE', #31416, #25970 ) ; +#30908 = EDGE_CURVE ( 'NONE', #90971, #76626, #92749, .T. ) ; +#30909 = LINE ( 'NONE', #62089, #35589 ) ; +#30910 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1869, 'distance_accuracy_value', 'NONE'); +#30911 = SURFACE_SIDE_STYLE ('',( #53901 ) ) ; +#30912 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#30913 = ORIENTED_EDGE ( 'NONE', *, *, #78346, .T. ) ; +#30914 = SURFACE_STYLE_FILL_AREA ( #24306 ) ; +#30915 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#30916 = FILL_AREA_STYLE_COLOUR ( '', #52692 ) ; +#30917 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639962, -1.100000000000000089, 3.495651678169978796E-76 ) ) ; +#30918 = PRESENTATION_STYLE_ASSIGNMENT (( #14552 ) ) ; +#30919 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.6999999999999999556, -0.02000000000001393372 ) ) ; +#30920 = LINE ( 'NONE', #39595, #59341 ) ; +#30921 = ADVANCED_FACE ( 'NONE', ( #39162 ), #85119, .T. ) ; +#30922 = EDGE_LOOP ( 'NONE', ( #12602, #10795, #23105, #41286 ) ) ; +#30923 = VECTOR ( 'NONE', #37101, 999.9999999999998863 ) ; +#30924 = FILL_AREA_STYLE_COLOUR ( '', #71704 ) ; +#30925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49285, 'distance_accuracy_value', 'NONE'); +#30926 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#30927 = EDGE_CURVE ( 'NONE', #28835, #15979, #57544, .T. ) ; +#30928 = SURFACE_STYLE_USAGE ( .BOTH. , #55462 ) ; +#30929 = ORIENTED_EDGE ( 'NONE', *, *, #200, .F. ) ; +#30930 = ORIENTED_EDGE ( 'NONE', *, *, #17504, .T. ) ; +#30931 = PRESENTATION_STYLE_ASSIGNMENT (( #46214 ) ) ; +#30932 = LINE ( 'NONE', #54445, #45866 ) ; +#30933 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48967 ), #83214 ) ; +#30934 = ORIENTED_EDGE ( 'NONE', *, *, #28088, .T. ) ; +#30935 = LINE ( 'NONE', #28926, #91768 ) ; +#30936 = CARTESIAN_POINT ( 'NONE', ( 0.03293650051631569903, -1.463352833475739967, 0.8100000000000000533 ) ) ; +#30937 = SURFACE_STYLE_FILL_AREA ( #53428 ) ; +#30938 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#30939 = SURFACE_SIDE_STYLE ('',( #38117 ) ) ; +#30941 = EDGE_CURVE ( 'NONE', #82338, #69855, #2395, .T. ) ; +#30940 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #22578, #52246 ), + ( #52729, #91518 ), + ( #92978, #83866 ), + ( #69519, #45509 ), + ( #30717, #29726 ), + ( #37422, #22071 ), + ( #12839, #61909 ), + ( #75695, #53235 ), + ( #92497, #84364 ), + ( #29240, #6675 ), + ( #44046, #28723 ), + ( #100070, #5203 ), + ( #61414, #99088 ), + ( #67510, #5706 ), + ( #59917, #91019 ), + ( #21085, #89 ), + ( #24119, #39920 ), + ( #86891, #70543 ), + ( #48611, #1635 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07262420069925890065, 0.1409697380364549890, 0.2055366295679730004, 0.2676612739694340104, 0.3281077529712519980, 0.3860824970032359915, 0.4440362253586940255, 0.5028572737747709631, 0.5616398490097329610, 0.6205525397731670445, 0.6796569225256300362, 0.7396960970132969715, 0.8012890424661629485, 0.8652792752259249598, 0.9314409141162129924, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#30942 = EDGE_CURVE ( 'NONE', #21399, #63401, #95269, .T. ) ; +#30943 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26096 ), #14573 ) ; +#30944 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #100556, #58257 ) ; +#30945 = VECTOR ( 'NONE', #69881, 1000.000000000000000 ) ; +#30946 = EDGE_CURVE ( 'NONE', #38761, #32892, #50878, .T. ) ; +#30947 = EDGE_LOOP ( 'NONE', ( #95348, #18885, #76328, #74766 ) ) ; +#30948 = EDGE_CURVE ( 'NONE', #38466, #82829, #41201, .T. ) ; +#30950 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.5000000000000015543, 0.000000000000000000 ) ) ; +#30949 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94559 ), #53763 ) ; +#30951 = STYLED_ITEM ( 'NONE', ( #80870 ), #93875 ) ; +#30952 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.1600000000000000033, 1.250000000000000000 ) ) ; +#30954 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#30953 = SURFACE_SIDE_STYLE ('',( #85065 ) ) ; +#30955 = ORIENTED_EDGE ( 'NONE', *, *, #63748, .F. ) ; +#30956 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96171 ) ) ; +#30957 = FILL_AREA_STYLE_COLOUR ( '', #98755 ) ; +#30958 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8648700000000000276 ) ) ; +#30959 = EDGE_CURVE ( 'NONE', #59395, #72636, #80011, .T. ) ; +#30960 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30961 = FILL_AREA_STYLE_COLOUR ( '', #46549 ) ; +#30962 = VERTEX_POINT ( 'NONE', #41704 ) ; +#30964 = FILL_AREA_STYLE_COLOUR ( '', #17537 ) ; +#30963 = FACE_OUTER_BOUND ( 'NONE', #38246, .T. ) ; +#30965 = VERTEX_POINT ( 'NONE', #49351 ) ; +#30966 = ORIENTED_EDGE ( 'NONE', *, *, #63721, .T. ) ; +#30967 = ADVANCED_FACE ( 'NONE', ( #19712 ), #34054, .T. ) ; +#30969 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#30968 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30970 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89657 ) ) ; +#30971 = FILL_AREA_STYLE ('',( #46771 ) ) ; +#30972 = ORIENTED_EDGE ( 'NONE', *, *, #87845, .F. ) ; +#30973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#30974 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999999556, -3.123820061220045297, -0.02000000000000000042 ) ) ; +#30975 = DIRECTION ( 'NONE', ( 0.7071090539100487460, -0.7071045084557415761, 0.000000000000000000 ) ) ; +#30976 = VERTEX_POINT ( 'NONE', #81023 ) ; +#30977 = SURFACE_STYLE_USAGE ( .BOTH. , #7410 ) ; +#30978 = ORIENTED_EDGE ( 'NONE', *, *, #85474, .T. ) ; +#30979 = ORIENTED_EDGE ( 'NONE', *, *, #61123, .T. ) ; +#30980 = SURFACE_STYLE_USAGE ( .BOTH. , #844 ) ; +#30981 = CARTESIAN_POINT ( 'NONE', ( 0.9689116169396260192, -1.374349516767729984, 0.8299999999999999600 ) ) ; +#30982 = PRESENTATION_STYLE_ASSIGNMENT (( #846 ) ) ; +#30983 = SURFACE_SIDE_STYLE ('',( #48847 ) ) ; +#30984 = VECTOR ( 'NONE', #99418, 1000.000000000000000 ) ; +#30985 = AXIS2_PLACEMENT_3D ( 'NONE', #60676, #92763, #29009 ) ; +#30986 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#30987 = CARTESIAN_POINT ( 'NONE', ( -0.02181523387524260046, -1.116141175150469955, 0.8100000000000000533 ) ) ; +#30988 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#30989 = LINE ( 'NONE', #21322, #56821 ) ; +#30990 = ORIENTED_EDGE ( 'NONE', *, *, #96445, .T. ) ; +#30991 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#30992 = ORIENTED_EDGE ( 'NONE', *, *, #14578, .F. ) ; +#30993 = ADVANCED_FACE ( 'NONE', ( #29382 ), #28381, .T. ) ; +#30995 = SURFACE_STYLE_FILL_AREA ( #8428 ) ; +#30994 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999998891, 0.8991599999999999593 ) ) ; +#30996 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666667052, 2.500000000000000000, 3.495651678170177615E-76 ) ) ; +#30997 = STYLED_ITEM ( 'NONE', ( #1047 ), #44802 ) ; +#30998 = PLANE ( 'NONE', #81058 ) ; +#30999 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31000 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31001 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#31002 = LINE ( 'NONE', #32018, #100564 ) ; +#31003 = ADVANCED_FACE ( 'NONE', ( #61048 ), #12977, .T. ) ; +#31004 = FILL_AREA_STYLE ('',( #24390 ) ) ; +#31005 = VERTEX_POINT ( 'NONE', #21706 ) ; +#31006 = FILL_AREA_STYLE_COLOUR ( '', #8405 ) ; +#31007 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31008 = SURFACE_STYLE_USAGE ( .BOTH. , #29000 ) ; +#31009 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31010 = FILL_AREA_STYLE_COLOUR ( '', #61526 ) ; +#31011 = AXIS2_PLACEMENT_3D ( 'NONE', #56970, #42129, #25314 ) ; +#31012 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#31013 = LINE ( 'NONE', #87660, #80671 ) ; +#31014 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100315, 'distance_accuracy_value', 'NONE'); +#31015 = CARTESIAN_POINT ( 'NONE', ( -1.233333333333333393, 3.500000000000000000, 0.000000000000000000 ) ) ; +#31017 = PLANE ( 'NONE', #55656 ) ; +#31016 = VECTOR ( 'NONE', #69216, 1000.000000000000000 ) ; +#31018 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31019 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31020 = FILL_AREA_STYLE ('',( #38682 ) ) ; +#31021 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#31022 = FILL_AREA_STYLE_COLOUR ( '', #15274 ) ; +#31023 = AXIS2_PLACEMENT_3D ( 'NONE', #46391, #38266, #29587 ) ; +#31024 = VECTOR ( 'NONE', #35376, 1000.000000000000000 ) ; +#31025 = PRESENTATION_STYLE_ASSIGNMENT (( #51138 ) ) ; +#31026 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31027 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#31028 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#31029 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31030 = VERTEX_POINT ( 'NONE', #13470 ) ; +#31031 = SURFACE_STYLE_FILL_AREA ( #378 ) ; +#31032 = ADVANCED_FACE ( 'NONE', ( #60057 ), #21211, .T. ) ; +#31033 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84808 ), #37540 ) ; +#31034 = CARTESIAN_POINT ( 'NONE', ( 1.599803260885759970, -1.408946430034399899, 0.8299999999999977396 ) ) ; +#31035 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42903, 'distance_accuracy_value', 'NONE'); +#31037 = VECTOR ( 'NONE', #65302, 1000.000000000000000 ) ; +#31038 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31039 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26183 ) ) ; +#31040 = SURFACE_STYLE_USAGE ( .BOTH. , #53532 ) ; +#31041 = CARTESIAN_POINT ( 'NONE', ( 1.826147860666869960, -1.473933850988760064, 0.8300000000000011813 ) ) ; +#31042 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31043 = STYLED_ITEM ( 'NONE', ( #60050 ), #64501 ) ; +#31044 = ORIENTED_EDGE ( 'NONE', *, *, #27607, .F. ) ; +#31045 = VECTOR ( 'NONE', #12354, 1000.000000000000000 ) ; +#31046 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#31047 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89720 ), #45654 ) ; +#31048 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31049 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79984 ), #8143 ) ; +#31050 = LINE ( 'NONE', #47377, #16838 ) ; +#31051 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14260, 'distance_accuracy_value', 'NONE'); +#31053 = CARTESIAN_POINT ( 'NONE', ( 11.67113275024997598, 5.245914249750025071, 0.8991599999999999593 ) ) ; +#31054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94578, 'distance_accuracy_value', 'NONE'); +#31055 = FILL_AREA_STYLE_COLOUR ( '', #74669 ) ; +#31056 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#31057 = VERTEX_POINT ( 'NONE', #737 ) ; +#31058 = VERTEX_POINT ( 'NONE', #47205 ) ; +#31059 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8648700000000000276 ) ) ; +#31060 = ORIENTED_EDGE ( 'NONE', *, *, #51620, .T. ) ; +#31061 = PLANE ( 'NONE', #72335 ) ; +#31062 = CARTESIAN_POINT ( 'NONE', ( -0.7059659090909090606, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#31063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31064 = SURFACE_STYLE_FILL_AREA ( #77018 ) ; +#31065 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10716, 'distance_accuracy_value', 'NONE'); +#31066 = SHAPE_DEFINITION_REPRESENTATION ( #49820, #67732 ) ; +#31067 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31069 = ORIENTED_EDGE ( 'NONE', *, *, #72699, .F. ) ; +#31068 = VERTEX_POINT ( 'NONE', #69129 ) ; +#31070 = VERTEX_POINT ( 'NONE', #31385 ) ; +#31071 = EDGE_CURVE ( 'NONE', #17126, #100318, #74580, .T. ) ; +#31072 = SURFACE_SIDE_STYLE ('',( #100875 ) ) ; +#31073 = CARTESIAN_POINT ( 'NONE', ( 1.793184587716770029, -1.490633633148249926, 0.8100000000000000533 ) ) ; +#31075 = FACE_OUTER_BOUND ( 'NONE', #71527, .T. ) ; +#31074 = FILL_AREA_STYLE ('',( #6997 ) ) ; +#31076 = ORIENTED_EDGE ( 'NONE', *, *, #58837, .T. ) ; +#31077 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#31078 = FACE_OUTER_BOUND ( 'NONE', #10482, .T. ) ; +#31079 = STYLED_ITEM ( 'NONE', ( #60530 ), #18136 ) ; +#31080 = CIRCLE ( 'NONE', #31011, 0.009999999999999998473 ) ; +#31082 = SURFACE_STYLE_USAGE ( .BOTH. , #100883 ) ; +#31081 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31083 = EDGE_LOOP ( 'NONE', ( #90221, #97155, #91497, #52640 ) ) ; +#31084 = CARTESIAN_POINT ( 'NONE', ( -0.4841855288935910107, -0.9911177488655089629, 0.8100000000000000533 ) ) ; +#31085 = EDGE_LOOP ( 'NONE', ( #7393, #97629, #29108, #88844 ) ) ; +#31086 = ORIENTED_EDGE ( 'NONE', *, *, #52136, .F. ) ; +#31087 = EDGE_CURVE ( 'NONE', #27723, #68837, #44166, .T. ) ; +#31088 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18955 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48833, #57510, #58030 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31089 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31090 = CARTESIAN_POINT ( 'NONE', ( -0.6166666666666659191, -3.099999999999989875, 0.000000000000000000 ) ) ; +#31091 = FILL_AREA_STYLE_COLOUR ( '', #47425 ) ; +#31092 = PLANE ( 'NONE', #21178 ) ; +#31093 = AXIS2_PLACEMENT_3D ( 'NONE', #75933, #37647, #68748 ) ; +#31094 = ORIENTED_EDGE ( 'NONE', *, *, #74213, .F. ) ; +#31095 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87081 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22017, #99030, #38364 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31096 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65948 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22198, #40568, #70670 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31097 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31098 = PLANE ( 'NONE', #96160 ) ; +#31099 = ORIENTED_EDGE ( 'NONE', *, *, #56925, .F. ) ; +#31100 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37609 ), #6545 ) ; +#31102 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#31101 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31103 = PRESENTATION_STYLE_ASSIGNMENT (( #39776 ) ) ; +#31104 = VERTEX_POINT ( 'NONE', #100205 ) ; +#31105 = EDGE_LOOP ( 'NONE', ( #73430, #91859, #32350, #18352 ) ) ; +#31107 = LINE ( 'NONE', #6550, #45366 ) ; +#31106 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#31108 = STYLED_ITEM ( 'NONE', ( #31969 ), #7104 ) ; +#31109 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5000000000000000000, -12.64499999999999957 ) ) ; +#31110 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31111 = SURFACE_STYLE_USAGE ( .BOTH. , #48476 ) ; +#31112 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31113 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31114 = LINE ( 'NONE', #52106, #55760 ) ; +#31115 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333323090, -0.2999999999999999889, 1.747825839084783216E-76 ) ) ; +#31116 = EDGE_CURVE ( 'NONE', #40642, #24344, #51817, .T. ) ; +#31117 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31118 = VECTOR ( 'NONE', #36425, 1000.000000000000227 ) ; +#31119 = ORIENTED_EDGE ( 'NONE', *, *, #41634, .F. ) ; +#31120 = FACE_OUTER_BOUND ( 'NONE', #72200, .T. ) ; +#31121 = STYLED_ITEM ( 'NONE', ( #77730 ), #2064 ) ; +#31122 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31123 = ORIENTED_EDGE ( 'NONE', *, *, #53580, .T. ) ; +#31124 = PLANE ( 'NONE', #60310 ) ; +#31125 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#31126 = SURFACE_STYLE_FILL_AREA ( #68400 ) ; +#31127 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#31129 = FILL_AREA_STYLE_COLOUR ( '', #72773 ) ; +#31128 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2784314575050761964, -0.1458578643762690474 ) ) ; +#31130 = SURFACE_STYLE_USAGE ( .BOTH. , #48493 ) ; +#31131 = ADVANCED_FACE ( 'NONE', ( #47718 ), #24262, .T. ) ; +#31132 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31133 = LINE ( 'NONE', #16274, #88581 ) ; +#31134 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#31135 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#31136 = PLANE ( 'NONE', #28434 ) ; +#31137 = SURFACE_STYLE_FILL_AREA ( #29253 ) ; +#31138 = STYLED_ITEM ( 'NONE', ( #86539 ), #51532 ) ; +#31139 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31140 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31141 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33958 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90857, #20905, #75051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31142 = STYLED_ITEM ( 'NONE', ( #73157 ), #10363 ) ; +#31143 = FACE_OUTER_BOUND ( 'NONE', #49811, .T. ) ; +#31145 = LINE ( 'NONE', #47466, #24096 ) ; +#31144 = LINE ( 'NONE', #83269, #60588 ) ; +#31146 = SURFACE_STYLE_FILL_AREA ( #53629 ) ; +#31148 = STYLED_ITEM ( 'NONE', ( #23536 ), #45109 ) ; +#31147 = PRESENTATION_STYLE_ASSIGNMENT (( #24018 ) ) ; +#31149 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31150 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77481, 'distance_accuracy_value', 'NONE'); +#31151 = EDGE_LOOP ( 'NONE', ( #83817, #66375, #94991, #75557 ) ) ; +#31152 = SURFACE_STYLE_FILL_AREA ( #7572 ) ; +#31153 = EDGE_CURVE ( 'NONE', #12557, #41763, #22724, .T. ) ; +#31154 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31155 = PRESENTATION_STYLE_ASSIGNMENT (( #42233 ) ) ; +#31156 = CARTESIAN_POINT ( 'NONE', ( 5.540517499499825860, 8.802661499499825126, 0.8991599999999999593 ) ) ; +#31157 = LINE ( 'NONE', #79657, #30715 ) ; +#31158 = FILL_AREA_STYLE_COLOUR ( '', #1403 ) ; +#31159 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#31160 = EDGE_CURVE ( 'NONE', #71387, #14941, #93122, .T. ) ; +#31161 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #4478 ) ; +#31162 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71759 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20307, #73953, #19824 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31163 = VERTEX_POINT ( 'NONE', #30346 ) ; +#31164 = ORIENTED_EDGE ( 'NONE', *, *, #39607, .F. ) ; +#31165 = DIRECTION ( 'NONE', ( -9.035018104045849247E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31166 = STYLED_ITEM ( 'NONE', ( #75810 ), #58004 ) ; +#31167 = PLANE ( 'NONE', #54786 ) ; +#31168 = SURFACE_STYLE_USAGE ( .BOTH. , #38833 ) ; +#31169 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#31170 = STYLED_ITEM ( 'NONE', ( #83871 ), #94753 ) ; +#31171 = SURFACE_SIDE_STYLE ('',( #78148 ) ) ; +#31172 = FACE_OUTER_BOUND ( 'NONE', #76762, .T. ) ; +#31173 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31174 = ORIENTED_EDGE ( 'NONE', *, *, #6490, .T. ) ; +#31175 = EDGE_CURVE ( 'NONE', #84785, #66220, #23239, .T. ) ; +#31176 = CARTESIAN_POINT ( 'NONE', ( 1.059879982250959918, -1.052467830684129968, 0.8300000000000002931 ) ) ; +#31177 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31178 = VECTOR ( 'NONE', #82958, 1000.000000000000000 ) ; +#31179 = EDGE_CURVE ( 'NONE', #28089, #46887, #61556, .T. ) ; +#31180 = ORIENTED_EDGE ( 'NONE', *, *, #29604, .T. ) ; +#31181 = PLANE ( 'NONE', #36053 ) ; +#31182 = VECTOR ( 'NONE', #29416, 1000.000000000000000 ) ; +#31183 = STYLED_ITEM ( 'NONE', ( #72590 ), #65893 ) ; +#31184 = VERTEX_POINT ( 'NONE', #38547 ) ; +#31185 = SURFACE_STYLE_FILL_AREA ( #79686 ) ; +#31186 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#31187 = LINE ( 'NONE', #76631, #85465 ) ; +#31188 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#31189 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26785 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61805, #45913, #41216 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31190 = CARTESIAN_POINT ( 'NONE', ( 12.44599999999999973, 8.305799999999999628, 0.8991599999999999593 ) ) ; +#31191 = CARTESIAN_POINT ( 'NONE', ( 1.877682030168900118, -1.070769809704489983, 0.8100000000000000533 ) ) ; +#31192 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31193 = AXIS2_PLACEMENT_3D ( 'NONE', #445, #70385, #31601 ) ; +#31195 = ORIENTED_EDGE ( 'NONE', *, *, #41353, .T. ) ; +#31194 = ORIENTED_EDGE ( 'NONE', *, *, #69418, .F. ) ; +#31196 = VECTOR ( 'NONE', #4089, 1000.000000000000000 ) ; +#31197 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999985359, 0.1400000000000000133 ) ) ; +#31198 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8648700000000000276 ) ) ; +#31199 = EDGE_LOOP ( 'NONE', ( #87835, #36199, #45499, #5570 ) ) ; +#31200 = ADVANCED_FACE ( 'NONE', ( #100694 ), #62056, .T. ) ; +#31201 = PRESENTATION_STYLE_ASSIGNMENT (( #54707 ) ) ; +#31202 = ORIENTED_EDGE ( 'NONE', *, *, #97472, .F. ) ; +#31203 = ORIENTED_EDGE ( 'NONE', *, *, #53461, .T. ) ; +#31204 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31205 = SURFACE_STYLE_USAGE ( .BOTH. , #12283 ) ; +#31206 = SURFACE_STYLE_FILL_AREA ( #86331 ) ; +#31207 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31208 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#31209 = ORIENTED_EDGE ( 'NONE', *, *, #15368, .T. ) ; +#31210 = ORIENTED_EDGE ( 'NONE', *, *, #49884, .F. ) ; +#31211 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76747, #69570, #39449, #47623 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31212 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#31213 = AXIS2_PLACEMENT_3D ( 'NONE', #83585, #83080, #13544 ) ; +#31214 = ORIENTED_EDGE ( 'NONE', *, *, #52385, .T. ) ; +#31215 = ADVANCED_FACE ( 'NONE', ( #88036 ), #87806, .F. ) ; +#31216 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3048 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76894, #77378, #69715 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31218 = EDGE_LOOP ( 'NONE', ( #61722, #44477, #48901, #25083 ) ) ; +#31217 = FACE_OUTER_BOUND ( 'NONE', #32746, .T. ) ; +#31219 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000002580, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#31220 = LINE ( 'NONE', #39371, #62878 ) ; +#31221 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#31222 = ORIENTED_EDGE ( 'NONE', *, *, #13107, .T. ) ; +#31223 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31224 = ORIENTED_EDGE ( 'NONE', *, *, #98290, .F. ) ; +#31225 = SURFACE_SIDE_STYLE ('',( #45497 ) ) ; +#31226 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3478 ) ) ; +#31228 = ORIENTED_EDGE ( 'NONE', *, *, #12324, .F. ) ; +#31227 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31229 = CARTESIAN_POINT ( 'NONE', ( 1.263299480776550077, -0.8906029366306310591, 0.8299999999999998490 ) ) ; +#31230 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31231 = CARTESIAN_POINT ( 'NONE', ( 1.525795062450169937, -1.430103682213279992, 0.8299999999999999600 ) ) ; +#31232 = EDGE_CURVE ( 'NONE', #7315, #80272, #57412, .T. ) ; +#31233 = SURFACE_STYLE_USAGE ( .BOTH. , #67623 ) ; +#31234 = LINE ( 'NONE', #80, #8048 ) ; +#31235 = LINE ( 'NONE', #24634, #51182 ) ; +#31236 = ORIENTED_EDGE ( 'NONE', *, *, #81884, .T. ) ; +#31237 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6669 ), #9942 ) ; +#31238 = LINE ( 'NONE', #93489, #74054 ) ; +#31239 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3496 ) ) ; +#31240 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.300000000000000266, -3.118622929693471946E-90 ) ) ; +#31241 = LINE ( 'NONE', #17913, #5735 ) ; +#31242 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#31244 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31243 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31245 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#31246 = EDGE_CURVE ( 'NONE', #56237, #86178, #49756, .T. ) ; +#31247 = VECTOR ( 'NONE', #48184, 1000.000000000000000 ) ; +#31248 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#31249 = ORIENTED_EDGE ( 'NONE', *, *, #56197, .T. ) ; +#31250 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31251 = ORIENTED_EDGE ( 'NONE', *, *, #98772, .T. ) ; +#31252 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31253 = SURFACE_SIDE_STYLE ('',( #92992 ) ) ; +#31254 = VECTOR ( 'NONE', #25348, 1000.000000000000000 ) ; +#31255 = SURFACE_SIDE_STYLE ('',( #86908 ) ) ; +#31256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31257 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#31258 = ORIENTED_EDGE ( 'NONE', *, *, #1706, .F. ) ; +#31259 = CARTESIAN_POINT ( 'NONE', ( 1.864400774706999941, -0.9907810524907123551, 0.8100000000000008304 ) ) ; +#31260 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31261 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01499999999999995781, -0.1458578643762691029 ) ) ; +#31262 = SURFACE_STYLE_FILL_AREA ( #15923 ) ; +#31263 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#31264 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#31265 = SURFACE_STYLE_USAGE ( .BOTH. , #55782 ) ; +#31266 = CARTESIAN_POINT ( 'NONE', ( 1.666984577922079991, -1.164935064935060050, 0.8100000000000000533 ) ) ; +#31267 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#31268 = PRESENTATION_STYLE_ASSIGNMENT (( #61443 ) ) ; +#31269 = CARTESIAN_POINT ( 'NONE', ( -0.1054344056808270008, -0.9001170352889870108, 0.8299999999999999600 ) ) ; +#31270 = EDGE_CURVE ( 'NONE', #68209, #68921, #80902, .T. ) ; +#31271 = EDGE_CURVE ( 'NONE', #67390, #83102, #73714, .T. ) ; +#31272 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31273 = ORIENTED_EDGE ( 'NONE', *, *, #98589, .T. ) ; +#31274 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 9.350000000000001421, 0.03429000000000000103 ) ) ; +#31275 = EDGE_LOOP ( 'NONE', ( #95242, #79312, #1864, #69541 ) ) ; +#31276 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19852 ) ) ; +#31277 = SURFACE_STYLE_USAGE ( .BOTH. , #48128 ) ; +#31278 = LINE ( 'NONE', #53761, #3097 ) ; +#31279 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#31280 = PLANE ( 'NONE', #68402 ) ; +#31281 = PRESENTATION_STYLE_ASSIGNMENT (( #79275 ) ) ; +#31282 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31283 = SURFACE_STYLE_USAGE ( .BOTH. , #69046 ) ; +#31284 = PRESENTATION_STYLE_ASSIGNMENT (( #53772 ) ) ; +#31285 = ORIENTED_EDGE ( 'NONE', *, *, #2927, .T. ) ; +#31286 = EDGE_CURVE ( 'NONE', #89125, #41045, #26769, .T. ) ; +#31287 = SURFACE_STYLE_USAGE ( .BOTH. , #78279 ) ; +#31288 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31289 = EDGE_CURVE ( 'NONE', #66049, #51979, #51450, .T. ) ; +#31290 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31291 = ORIENTED_EDGE ( 'NONE', *, *, #11587, .T. ) ; +#31292 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#31293 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49402 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95769, #39666, #87646 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31294 = FACE_OUTER_BOUND ( 'NONE', #11529, .T. ) ; +#31295 = EDGE_LOOP ( 'NONE', ( #9123, #60719, #22397, #81980 ) ) ; +#31296 = ADVANCED_FACE ( 'NONE', ( #27272 ), #48242, .T. ) ; +#31297 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#31298 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12247 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89419, #18446, #18957 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31299 = FILL_AREA_STYLE_COLOUR ( '', #54446 ) ; +#31300 = VECTOR ( 'NONE', #5493, 1000.000000000000000 ) ; +#31301 = FILL_AREA_STYLE_COLOUR ( '', #54315 ) ; +#31302 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.009999999999999998473, 1.250000000000000000 ) ) ; +#31303 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #50203, #12210 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #76910 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#31304 = VERTEX_POINT ( 'NONE', #68029 ) ; +#31305 = AXIS2_PLACEMENT_3D ( 'NONE', #31968, #23303, #94721 ) ; +#31306 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999659677 ) ) ; +#31307 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37806 ), #63912 ) ; +#31308 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8648700000000000276 ) ) ; +#31309 = EDGE_CURVE ( 'NONE', #47678, #23828, #90539, .T. ) ; +#31310 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31311 = FILL_AREA_STYLE ('',( #31818 ) ) ; +#31312 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10441 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75569, #46404, #69373 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31313 = VERTEX_POINT ( 'NONE', #4757 ) ; +#31314 = ADVANCED_FACE ( 'NONE', ( #11833 ), #43557, .F. ) ; +#31315 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31316 = AXIS2_PLACEMENT_3D ( 'NONE', #54291, #92062, #142 ) ; +#31317 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31318 = ORIENTED_EDGE ( 'NONE', *, *, #47052, .T. ) ; +#31319 = ORIENTED_EDGE ( 'NONE', *, *, #31309, .F. ) ; +#31320 = VERTEX_POINT ( 'NONE', #82885 ) ; +#31321 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34433, #94267, #77973, #65527 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31322 = ADVANCED_FACE ( 'NONE', ( #91535 ), #75235, .F. ) ; +#31323 = EDGE_CURVE ( 'NONE', #51680, #96032, #2023, .T. ) ; +#31324 = AXIS2_PLACEMENT_3D ( 'NONE', #80347, #2736, #81373 ) ; +#31325 = VERTEX_POINT ( 'NONE', #63818 ) ; +#31327 = ORIENTED_EDGE ( 'NONE', *, *, #62935, .F. ) ; +#31326 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#31328 = EDGE_CURVE ( 'NONE', #5274, #91118, #491, .T. ) ; +#31329 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31330 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31331 = CIRCLE ( 'NONE', #55773, 0.1499999999999999944 ) ; +#31332 = EDGE_LOOP ( 'NONE', ( #13190, #48013, #2155, #49331 ) ) ; +#31333 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31334 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#31335 = VERTEX_POINT ( 'NONE', #55663 ) ; +#31336 = PRODUCT_DEFINITION ( 'δ֪', '', #35643, #39188 ) ; +#31337 = DIRECTION ( 'NONE', ( -0.3387340427540271870, 0.000000000000000000, -0.9408821649279535126 ) ) ; +#31338 = SURFACE_SIDE_STYLE ('',( #16493 ) ) ; +#31339 = VECTOR ( 'NONE', #52009, 1000.000000000000000 ) ; +#31340 = ORIENTED_EDGE ( 'NONE', *, *, #66316, .F. ) ; +#31342 = PLANE ( 'NONE', #42150 ) ; +#31341 = CARTESIAN_POINT ( 'NONE', ( -1.325735931288071212, 0.6599999999999999201, 1.100000000000000089 ) ) ; +#31343 = ORIENTED_EDGE ( 'NONE', *, *, #10675, .T. ) ; +#31344 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73741 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56750, #70512, #62378 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31346 = SURFACE_STYLE_USAGE ( .BOTH. , #20671 ) ; +#31345 = SURFACE_STYLE_USAGE ( .BOTH. , #92595 ) ; +#31347 = CARTESIAN_POINT ( 'NONE', ( 0.05920294988330667557, -1.204209032300494142, 0.8099999999999409894 ) ) ; +#31348 = EDGE_CURVE ( 'NONE', #25700, #43256, #87274, .T. ) ; +#31349 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31350 = VECTOR ( 'NONE', #37857, 1000.000000000000000 ) ; +#31351 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#31352 = VERTEX_POINT ( 'NONE', #31642 ) ; +#31353 = AXIS2_PLACEMENT_3D ( 'NONE', #30241, #7193, #75718 ) ; +#31354 = VERTEX_POINT ( 'NONE', #32671 ) ; +#31355 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.98066299999999984, 0.8991599999999999593 ) ) ; +#31357 = LINE ( 'NONE', #93597, #6658 ) ; +#31356 = LINE ( 'NONE', #72188, #68923 ) ; +#31358 = FACE_OUTER_BOUND ( 'NONE', #37090, .T. ) ; +#31359 = EDGE_CURVE ( 'NONE', #75419, #82666, #56162, .T. ) ; +#31360 = LINE ( 'NONE', #54362, #89655 ) ; +#31361 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75390 ) ) ; +#31362 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22752 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39996, #48169, #31317 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31363 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#31365 = EDGE_CURVE ( 'NONE', #88429, #55234, #72451, .T. ) ; +#31364 = SURFACE_STYLE_USAGE ( .BOTH. , #713 ) ; +#31366 = FACE_BOUND ( 'NONE', #39247, .T. ) ; +#31367 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15956, #85922, #46605, #31292 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31368 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31369 = FILL_AREA_STYLE_COLOUR ( '', #33181 ) ; +#31370 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#31371 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31372 = LINE ( 'NONE', #62548, #38545 ) ; +#31373 = ORIENTED_EDGE ( 'NONE', *, *, #8813, .F. ) ; +#31374 = CARTESIAN_POINT ( 'NONE', ( -0.9854791524880751608, -1.205184960463220323, 0.8300000000000002931 ) ) ; +#31375 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.100000000000000089, -3.118622929693471946E-90 ) ) ; +#31377 = SURFACE_STYLE_USAGE ( .BOTH. , #6797 ) ; +#31376 = DIRECTION ( 'NONE', ( 0.7071090539100487460, -0.7071045084557415761, 0.000000000000000000 ) ) ; +#31378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31379 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55645, 'distance_accuracy_value', 'NONE'); +#31380 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#31381 = VECTOR ( 'NONE', #81653, 1000.000000000000000 ) ; +#31382 = LINE ( 'NONE', #38543, #72465 ) ; +#31383 = VECTOR ( 'NONE', #53816, 1000.000000000000000 ) ; +#31384 = PRESENTATION_STYLE_ASSIGNMENT (( #75837 ) ) ; +#31385 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.01000000000000000021, 0.2350000000000000144 ) ) ; +#31386 = ORIENTED_EDGE ( 'NONE', *, *, #67966, .F. ) ; +#31387 = FILL_AREA_STYLE_COLOUR ( '', #45575 ) ; +#31388 = LINE ( 'NONE', #79375, #64122 ) ; +#31389 = SURFACE_STYLE_USAGE ( .BOTH. , #24269 ) ; +#31390 = FILL_AREA_STYLE ('',( #8830 ) ) ; +#31391 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#31392 = PRESENTATION_STYLE_ASSIGNMENT (( #1257 ) ) ; +#31393 = STYLED_ITEM ( 'NONE', ( #79535 ), #66895 ) ; +#31394 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#31395 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31396 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31397 = CYLINDRICAL_SURFACE ( 'NONE', #88723, 1.874993856093760236 ) ; +#31398 = ADVANCED_FACE ( 'NONE', ( #2528 ), #62308, .T. ) ; +#31399 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44423 ), #18332 ) ; +#31400 = LINE ( 'NONE', #7329, #17486 ) ; +#31401 = CYLINDRICAL_SURFACE ( 'NONE', #27710, 0.3000000000000000444 ) ; +#31402 = SURFACE_STYLE_USAGE ( .BOTH. , #85521 ) ; +#31403 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#31404 = SURFACE_STYLE_USAGE ( .BOTH. , #23258 ) ; +#31405 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94931 ), #46009 ) ; +#31406 = VERTEX_POINT ( 'NONE', #85753 ) ; +#31407 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639962, -1.500000000000000000, 3.495651678169978796E-76 ) ) ; +#31408 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#31409 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#31410 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31411 = SURFACE_STYLE_FILL_AREA ( #55933 ) ; +#31412 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31413 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.2000000000000000111, -12.44500000000000028 ) ) ; +#31414 = CARTESIAN_POINT ( 'NONE', ( -0.9854791524880751608, -1.205184960463220323, 0.8299999999999999600 ) ) ; +#31415 = ORIENTED_EDGE ( 'NONE', *, *, #7646, .T. ) ; +#31416 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 8.413752999999999815, 0.8648700000000000276 ) ) ; +#31417 = FACE_OUTER_BOUND ( 'NONE', #30922, .T. ) ; +#31418 = EDGE_CURVE ( 'NONE', #17483, #49397, #23497, .T. ) ; +#31419 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#31420 = VECTOR ( 'NONE', #65056, 1000.000000000000000 ) ; +#31421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68439 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55050, #31035, #87180 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31422 = VERTEX_POINT ( 'NONE', #87786 ) ; +#31423 = SURFACE_STYLE_USAGE ( .BOTH. , #69172 ) ; +#31424 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31425 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#31426 = FILL_AREA_STYLE ('',( #30916 ) ) ; +#31427 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.383333333333323090, 0.000000000000000000 ) ) ; +#31428 = SURFACE_STYLE_FILL_AREA ( #30387 ) ; +#31429 = PRESENTATION_STYLE_ASSIGNMENT (( #93170 ) ) ; +#31430 = VECTOR ( 'NONE', #3376, 1000.000000000000000 ) ; +#31431 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31432 = ORIENTED_EDGE ( 'NONE', *, *, #98425, .T. ) ; +#31433 = SURFACE_SIDE_STYLE ('',( #52924 ) ) ; +#31434 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25712, 'distance_accuracy_value', 'NONE'); +#31435 = SURFACE_STYLE_USAGE ( .BOTH. , #56480 ) ; +#31436 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16257 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90664, #91164, #67650 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31437 = VECTOR ( 'NONE', #34329, 1000.000000000000000 ) ; +#31438 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31439 = VERTEX_POINT ( 'NONE', #55168 ) ; +#31440 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57577 ), #46124 ) ; +#31441 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49388 ), #60845 ) ; +#31442 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#31443 = SURFACE_STYLE_FILL_AREA ( #291 ) ; +#31444 = VERTEX_POINT ( 'NONE', #49005 ) ; +#31445 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#31446 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31447 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31448 = PRESENTATION_STYLE_ASSIGNMENT (( #44729 ) ) ; +#31449 = AXIS2_PLACEMENT_3D ( 'NONE', #75087, #35299, #42919 ) ; +#31450 = VECTOR ( 'NONE', #19986, 1000.000000000000000 ) ; +#31451 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31452 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #86044, #64844 ) ; +#31453 = CARTESIAN_POINT ( 'NONE', ( 0.2416038136213350396, -1.101447087279459947, 0.8299999999999999600 ) ) ; +#31454 = ADVANCED_FACE ( 'NONE', ( #71972 ), #39814, .T. ) ; +#31455 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59205 ) ) ; +#31456 = STYLED_ITEM ( 'NONE', ( #16655 ), #8961 ) ; +#31457 = EDGE_LOOP ( 'NONE', ( #41040, #90628, #62594, #12409 ) ) ; +#31458 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853417210, 1.551146575926969806, 0.8100000000000001643 ) ) ; +#31459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26584, 'distance_accuracy_value', 'NONE'); +#31460 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8299999999999999600 ) ) ; +#31462 = CYLINDRICAL_SURFACE ( 'NONE', #72557, 0.6999999999999999556 ) ; +#31461 = PRESENTATION_STYLE_ASSIGNMENT (( #54965 ) ) ; +#31463 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31464 = VERTEX_POINT ( 'NONE', #51023 ) ; +#31465 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31466 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.783333333333333437, 0.000000000000000000 ) ) ; +#31467 = PRESENTATION_STYLE_ASSIGNMENT (( #15085 ) ) ; +#31468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31469 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55989 ), #6961 ) ; +#31470 = ORIENTED_EDGE ( 'NONE', *, *, #30942, .F. ) ; +#31472 = FILL_AREA_STYLE ('',( #48334 ) ) ; +#31471 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#31473 = EDGE_LOOP ( 'NONE', ( #41039, #15771, #84372, #199 ) ) ; +#31474 = ORIENTED_EDGE ( 'NONE', *, *, #100383, .F. ) ; +#31475 = DIRECTION ( 'NONE', ( -0.7071071146859688739, 0.7071064476869688420, -0.000000000000000000 ) ) ; +#31476 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#31477 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62705 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65263, #26485, #88756 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31479 = ORIENTED_EDGE ( 'NONE', *, *, #80871, .T. ) ; +#31480 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -2.299999999999999822, 0.1829999999999500082 ) ) ; +#31481 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#31482 = EDGE_LOOP ( 'NONE', ( #54374, #43007, #38016, #84857 ) ) ; +#31484 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31483 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31485 = EDGE_LOOP ( 'NONE', ( #43925, #91886, #66706, #26294 ) ) ; +#31486 = ORIENTED_EDGE ( 'NONE', *, *, #92528, .F. ) ; +#31488 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31487 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31489 = EDGE_CURVE ( 'NONE', #39315, #68717, #27535, .T. ) ; +#31490 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#31491 = STYLED_ITEM ( 'NONE', ( #3869 ), #88092 ) ; +#31493 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99809 ), #51061 ) ; +#31492 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31494 = STYLED_ITEM ( 'NONE', ( #34861 ), #26133 ) ; +#31495 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#31496 = LINE ( 'NONE', #71310, #69491 ) ; +#31497 = VERTEX_POINT ( 'NONE', #33684 ) ; +#31498 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32944 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9310, #87497, #2253 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31499 = EDGE_CURVE ( 'NONE', #40173, #89795, #12110, .T. ) ; +#31500 = FACE_OUTER_BOUND ( 'NONE', #99016, .T. ) ; +#31501 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8099999999998432898 ) ) ; +#31502 = DIRECTION ( 'NONE', ( -0.7071067811865469066, -0.7071067811865482389, 0.000000000000000000 ) ) ; +#31503 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#31504 = FILL_AREA_STYLE ('',( #86123 ) ) ; +#31505 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#31506 = STYLED_ITEM ( 'NONE', ( #46711 ), #36307 ) ; +#31507 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#31508 = EDGE_CURVE ( 'NONE', #48839, #34164, #11598, .T. ) ; +#31509 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74263, #43111, #22129 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31510 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.000000000000000000 ) ) ; +#31511 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31512 = ORIENTED_EDGE ( 'NONE', *, *, #30565, .F. ) ; +#31513 = SURFACE_STYLE_USAGE ( .BOTH. , #17680 ) ; +#31514 = PLANE ( 'NONE', #90121 ) ; +#31515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31516 = STYLED_ITEM ( 'NONE', ( #73782 ), #37778 ) ; +#31518 = VECTOR ( 'NONE', #45404, 1000.000000000000000 ) ; +#31517 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#31519 = VECTOR ( 'NONE', #81148, 1000.000000000000000 ) ; +#31520 = FACE_OUTER_BOUND ( 'NONE', #94850, .T. ) ; +#31521 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31523 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#31524 = EDGE_CURVE ( 'NONE', #63739, #84529, #73491, .T. ) ; +#31525 = VECTOR ( 'NONE', #68329, 1000.000000000000000 ) ; +#31527 = ADVANCED_FACE ( 'NONE', ( #42344 ), #95919, .T. ) ; +#31526 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, 0.1200000000000003147, 0.2999999999999999889 ) ) ; +#31528 = STYLED_ITEM ( 'NONE', ( #38588 ), #96943 ) ; +#31529 = FILL_AREA_STYLE ('',( #85644 ) ) ; +#31530 = SURFACE_STYLE_FILL_AREA ( #69270 ) ; +#31531 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31532 = SURFACE_STYLE_FILL_AREA ( #23371 ) ; +#31533 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31534 = FILL_AREA_STYLE ('',( #78490 ) ) ; +#31535 = EDGE_CURVE ( 'NONE', #51201, #79728, #26024, .T. ) ; +#31536 = ADVANCED_FACE ( 'NONE', ( #90289 ), #49500, .F. ) ; +#31537 = LINE ( 'NONE', #42718, #16306 ) ; +#31538 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52757 ) ) ; +#31539 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #38043, #54377, #77323, #39046 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31540 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#31541 = CARTESIAN_POINT ( 'NONE', ( 8.383087000000001510, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#31542 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31543 = ORIENTED_EDGE ( 'NONE', *, *, #5894, .T. ) ; +#31544 = PRESENTATION_STYLE_ASSIGNMENT (( #67800 ) ) ; +#31545 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.476179938779914824, -0.02000000000000000042 ) ) ; +#31546 = EDGE_CURVE ( 'NONE', #10921, #22003, #36195, .T. ) ; +#31547 = CARTESIAN_POINT ( 'NONE', ( 1.077285631887885620, -0.9963620614100031636, 0.8099999999999921707 ) ) ; +#31548 = EDGE_CURVE ( 'NONE', #34361, #53458, #91295, .T. ) ; +#31549 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#31550 = ORIENTED_EDGE ( 'NONE', *, *, #38126, .T. ) ; +#31551 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#31552 = AXIS2_PLACEMENT_3D ( 'NONE', #32511, #55508, #40673 ) ; +#31553 = SURFACE_STYLE_FILL_AREA ( #99866 ) ; +#31554 = CARTESIAN_POINT ( 'NONE', ( 1.779394466811810016, -1.241062917987890257, 0.8299999999999994049 ) ) ; +#31555 = FILL_AREA_STYLE_COLOUR ( '', #92711 ) ; +#31556 = SURFACE_SIDE_STYLE ('',( #22376 ) ) ; +#31557 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93904 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19640, #56977, #65099 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31558 = ORIENTED_EDGE ( 'NONE', *, *, #58060, .F. ) ; +#31559 = ORIENTED_EDGE ( 'NONE', *, *, #2275, .F. ) ; +#31560 = VECTOR ( 'NONE', #80888, 1000.000000000000000 ) ; +#31561 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#31562 = ORIENTED_EDGE ( 'NONE', *, *, #79494, .T. ) ; +#31563 = CARTESIAN_POINT ( 'NONE', ( 0.3269029137381110339, -0.9653181426176251634, 0.8299999999999996270 ) ) ; +#31564 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#31565 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96767 ) ) ; +#31566 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31567 = CARTESIAN_POINT ( 'NONE', ( 1.566666666666656660, -3.500000000000000000, 0.000000000000000000 ) ) ; +#31568 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #7658 ) ; +#31569 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31571 = ORIENTED_EDGE ( 'NONE', *, *, #82376, .T. ) ; +#31570 = ORIENTED_EDGE ( 'NONE', *, *, #15116, .F. ) ; +#31572 = VECTOR ( 'NONE', #76077, 1000.000000000000000 ) ; +#31573 = EDGE_CURVE ( 'NONE', #75715, #60860, #52508, .T. ) ; +#31574 = ORIENTED_EDGE ( 'NONE', *, *, #100879, .T. ) ; +#31575 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31577 = VECTOR ( 'NONE', #47978, 1000.000000000000000 ) ; +#31576 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21349, 'distance_accuracy_value', 'NONE'); +#31578 = CARTESIAN_POINT ( 'NONE', ( 1.736267301452500300, -1.505252428432260148, 0.8299999999999999600 ) ) ; +#31579 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.699999999999999734, -3.118622929693471946E-90 ) ) ; +#31580 = ORIENTED_EDGE ( 'NONE', *, *, #36295, .T. ) ; +#31581 = EDGE_CURVE ( 'NONE', #67401, #14090, #14146, .T. ) ; +#31582 = SURFACE_SIDE_STYLE ('',( #427 ) ) ; +#31583 = VECTOR ( 'NONE', #68655, 1000.000000000000000 ) ; +#31584 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31585 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#31587 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 4.574163000000001311, 0.8648700000000000276 ) ) ; +#31586 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31588 = VERTEX_POINT ( 'NONE', #83146 ) ; +#31589 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8099999999999619726 ) ) ; +#31590 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88733 ) ) ; +#31591 = VERTEX_POINT ( 'NONE', #22348 ) ; +#31592 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #90506, #50738, #81872, #74193, #99078, #12830, #44520, #75687 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000006661, 0.5000000000000013323, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31593 = VERTEX_POINT ( 'NONE', #98379 ) ; +#31594 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31595 = PRESENTATION_STYLE_ASSIGNMENT (( #8014 ) ) ; +#31596 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000020983, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#31598 = ORIENTED_EDGE ( 'NONE', *, *, #31892, .F. ) ; +#31597 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31599 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31600 = FACE_OUTER_BOUND ( 'NONE', #87326, .T. ) ; +#31601 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31602 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31603 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#31604 = ORIENTED_EDGE ( 'NONE', *, *, #93828, .F. ) ; +#31605 = SURFACE_STYLE_FILL_AREA ( #17275 ) ; +#31606 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#31607 = ORIENTED_EDGE ( 'NONE', *, *, #55692, .T. ) ; +#31608 = EDGE_LOOP ( 'NONE', ( #32352, #98356, #23631, #47524 ) ) ; +#31610 = LINE ( 'NONE', #15234, #24229 ) ; +#31609 = LINE ( 'NONE', #62777, #47234 ) ; +#31611 = EDGE_CURVE ( 'NONE', #23180, #58245, #45301, .T. ) ; +#31612 = PLANE ( 'NONE', #2446 ) ; +#31613 = AXIS2_PLACEMENT_3D ( 'NONE', #38357, #39334, #14804 ) ; +#31614 = CARTESIAN_POINT ( 'NONE', ( -0.5424062986694020427, -1.258396457361969922, 0.8299999999999999600 ) ) ; +#31615 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19436, #52107, #66404, #35301 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31616 = AXIS2_PLACEMENT_3D ( 'NONE', #16530, #10315, #40574 ) ; +#31617 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31618 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.323820061220084998, 0.000000000000000000 ) ) ; +#31619 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23762, 'distance_accuracy_value', 'NONE'); +#31620 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31621 = EDGE_LOOP ( 'NONE', ( #92447, #83701, #33139, #64386 ) ) ; +#31622 = FACE_OUTER_BOUND ( 'NONE', #13140, .T. ) ; +#31623 = CARTESIAN_POINT ( 'NONE', ( -0.9123894243494741207, -1.359907766992060285, 0.8299999999999999600 ) ) ; +#31624 = ORIENTED_EDGE ( 'NONE', *, *, #43002, .T. ) ; +#31625 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31627 = PRESENTATION_STYLE_ASSIGNMENT (( #61794 ) ) ; +#31626 = SURFACE_STYLE_FILL_AREA ( #9572 ) ; +#31628 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#31629 = FILL_AREA_STYLE_COLOUR ( '', #15644 ) ; +#31630 = FACE_OUTER_BOUND ( 'NONE', #73659, .T. ) ; +#31631 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31632 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#31633 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#31634 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#31635 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31636 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31637 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#31638 = AXIS2_PLACEMENT_3D ( 'NONE', #29556, #35746, #67348 ) ; +#31639 = FILL_AREA_STYLE ('',( #77092 ) ) ; +#31640 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8648700000000000276 ) ) ; +#31641 = PRESENTATION_STYLE_ASSIGNMENT (( #62820 ) ) ; +#31642 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#31643 = FACE_OUTER_BOUND ( 'NONE', #83475, .T. ) ; +#31644 = ADVANCED_FACE ( 'NONE', ( #67792 ), #13111, .T. ) ; +#31645 = CIRCLE ( 'NONE', #88957, 0.09999999999999939493 ) ; +#31646 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12034 ) ) ; +#31647 = EDGE_LOOP ( 'NONE', ( #35899, #50540, #18874, #59859 ) ) ; +#31648 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, -1.899999999999999689, 0.000000000000000000 ) ) ; +#31649 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48870, 'distance_accuracy_value', 'NONE'); +#31650 = EDGE_LOOP ( 'NONE', ( #2080, #50662, #38735, #63634 ) ) ; +#31652 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83028, 'distance_accuracy_value', 'NONE'); +#31651 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31653 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#31655 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26810 ), #100054 ) ; +#31654 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52955, #45237, #77409 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31656 = FILL_AREA_STYLE ('',( #100466 ) ) ; +#31657 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31658 = EDGE_CURVE ( 'NONE', #60362, #80825, #68302, .T. ) ; +#31659 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88729 ), #671 ) ; +#31660 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 2.168404344971010347E-16 ) ) ; +#31661 = CARTESIAN_POINT ( 'NONE', ( 9.507386958374977937, 5.557040958374940942, 0.8648700000000000276 ) ) ; +#31662 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44611 ), #21823 ) ; +#31663 = EDGE_CURVE ( 'NONE', #40383, #47933, #53513, .T. ) ; +#31664 = STYLED_ITEM ( 'NONE', ( #40966 ), #29141 ) ; +#31665 = VERTEX_POINT ( 'NONE', #69272 ) ; +#31666 = ORIENTED_EDGE ( 'NONE', *, *, #19531, .F. ) ; +#31667 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24927, 'distance_accuracy_value', 'NONE'); +#31668 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11850, 'distance_accuracy_value', 'NONE'); +#31669 = VECTOR ( 'NONE', #83707, 1000.000000000000000 ) ; +#31670 = SURFACE_STYLE_FILL_AREA ( #90947 ) ; +#31671 = SURFACE_SIDE_STYLE ('',( #79149 ) ) ; +#31672 = CARTESIAN_POINT ( 'NONE', ( -0.1900794716924300021, -1.425091422160009946, 0.8299999999999995159 ) ) ; +#31673 = VECTOR ( 'NONE', #27753, 1000.000000000000000 ) ; +#31674 = FACE_OUTER_BOUND ( 'NONE', #42247, .T. ) ; +#31675 = LINE ( 'NONE', #16819, #30514 ) ; +#31676 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#31677 = STYLED_ITEM ( 'NONE', ( #22408 ), #68730 ) ; +#31678 = ORIENTED_EDGE ( 'NONE', *, *, #93476, .F. ) ; +#31679 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#31680 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999830802, 0.000000000000000000, 0.6914213562373291433 ) ) ; +#31681 = ORIENTED_EDGE ( 'NONE', *, *, #351, .T. ) ; +#31682 = VECTOR ( 'NONE', #79433, 1000.000000000000000 ) ; +#31683 = SURFACE_SIDE_STYLE ('',( #70472 ) ) ; +#31684 = ORIENTED_EDGE ( 'NONE', *, *, #36755, .T. ) ; +#31685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31686 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31687 = LINE ( 'NONE', #62862, #74282 ) ; +#31688 = LINE ( 'NONE', #44965, #15313 ) ; +#31689 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#31690 = SURFACE_SIDE_STYLE ('',( #7106 ) ) ; +#31691 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -1.900000000000000133, 0.000000000000000000 ) ) ; +#31694 = ORIENTED_EDGE ( 'NONE', *, *, #29396, .F. ) ; +#31693 = ORIENTED_EDGE ( 'NONE', *, *, #94391, .F. ) ; +#31692 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33315 ) ) ; +#31695 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#31696 = ORIENTED_EDGE ( 'NONE', *, *, #63547, .T. ) ; +#31697 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95854 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71520, #18370, #48556 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31698 = ORIENTED_EDGE ( 'NONE', *, *, #36279, .F. ) ; +#31699 = ADVANCED_FACE ( 'NONE', ( #30481 ), #92765, .T. ) ; +#31700 = VERTEX_POINT ( 'NONE', #23895 ) ; +#31701 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#31702 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8648700000000000276 ) ) ; +#31703 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61026 ), #80643 ) ; +#31704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90449 ) ) ; +#31705 = PRESENTATION_STYLE_ASSIGNMENT (( #38377 ) ) ; +#31707 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31706 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31708 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#31709 = ORIENTED_EDGE ( 'NONE', *, *, #65894, .F. ) ; +#31710 = ORIENTED_EDGE ( 'NONE', *, *, #89401, .F. ) ; +#31711 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33337 ) ) ; +#31712 = AXIS2_PLACEMENT_3D ( 'NONE', #7768, #17015, #696 ) ; +#31713 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31714 = ORIENTED_EDGE ( 'NONE', *, *, #58139, .F. ) ; +#31715 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #28536, #19363, #12130, #20369 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31716 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, 0.000000000000000000 ) ) ; +#31717 = ORIENTED_EDGE ( 'NONE', *, *, #40669, .F. ) ; +#31718 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#31719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41508 ), #10404 ) ; +#31720 = VECTOR ( 'NONE', #83531, 999.9999999999998863 ) ; +#31721 = SURFACE_STYLE_FILL_AREA ( #85842 ) ; +#31722 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31723 = VERTEX_POINT ( 'NONE', #56047 ) ; +#31725 = SURFACE_STYLE_FILL_AREA ( #87357 ) ; +#31724 = STYLED_ITEM ( 'NONE', ( #62445 ), #21667 ) ; +#31726 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31727 = ORIENTED_EDGE ( 'NONE', *, *, #89306, .F. ) ; +#31728 = ADVANCED_FACE ( 'NONE', ( #16666 ), #32558, .T. ) ; +#31729 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #731 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2493, #26993, #81628 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31731 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#31732 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31733 = ORIENTED_EDGE ( 'NONE', *, *, #20139, .F. ) ; +#31734 = PRESENTATION_STYLE_ASSIGNMENT (( #577 ) ) ; +#31735 = FILL_AREA_STYLE_COLOUR ( '', #68207 ) ; +#31737 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#31736 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#31738 = SURFACE_STYLE_FILL_AREA ( #4844 ) ; +#31739 = SURFACE_STYLE_FILL_AREA ( #92003 ) ; +#31740 = CARTESIAN_POINT ( 'NONE', ( 1.823014099396639942, -1.319025261726090026, 0.8099999999999996092 ) ) ; +#31741 = VERTEX_POINT ( 'NONE', #78488 ) ; +#31742 = PLANE ( 'NONE', #54538 ) ; +#31743 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 1.300000000000000266, 3.495651678170121160E-76 ) ) ; +#31745 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80686 ), #88822 ) ; +#31744 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000311, -0.02000000000000000042 ) ) ; +#31747 = LINE ( 'NONE', #40950, #39378 ) ; +#31746 = PRESENTATION_STYLE_ASSIGNMENT (( #590 ) ) ; +#31748 = SURFACE_STYLE_FILL_AREA ( #592 ) ; +#31749 = CYLINDRICAL_SURFACE ( 'NONE', #35374, 0.05000000000000002359 ) ; +#31750 = EDGE_CURVE ( 'NONE', #94979, #55827, #71855, .T. ) ; +#31751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31752 = EDGE_CURVE ( 'NONE', #45112, #90348, #39690, .T. ) ; +#31753 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93012 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24710, #55829, #86966 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31754 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#31755 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31756 = ORIENTED_EDGE ( 'NONE', *, *, #30096, .T. ) ; +#31757 = STYLED_ITEM ( 'NONE', ( #49724 ), #72513 ) ; +#31758 = FILL_AREA_STYLE ('',( #602 ) ) ; +#31759 = ORIENTED_EDGE ( 'NONE', *, *, #13336, .T. ) ; +#31760 = FACE_OUTER_BOUND ( 'NONE', #45193, .T. ) ; +#31761 = VECTOR ( 'NONE', #66656, 1000.000000000000000 ) ; +#31763 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31762 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#31764 = ADVANCED_FACE ( 'NONE', ( #8965 ), #40216, .T. ) ; +#31765 = VECTOR ( 'NONE', #56142, 1000.000000000000000 ) ; +#31766 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31767 = ORIENTED_EDGE ( 'NONE', *, *, #31179, .F. ) ; +#31768 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.850000000000000089, 0.000000000000000000 ) ) ; +#31769 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#31770 = CARTESIAN_POINT ( 'NONE', ( -0.06821911881269179800, -1.154690592117219916, 0.8300000000000005151 ) ) ; +#31771 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#31772 = CIRCLE ( 'NONE', #44794, 0.04999999999999969746 ) ; +#31773 = AXIS2_PLACEMENT_3D ( 'NONE', #66671, #51882, #88656 ) ; +#31774 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#31775 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#31776 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31777 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31778 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31779 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84809, 'distance_accuracy_value', 'NONE'); +#31780 = EDGE_CURVE ( 'NONE', #52774, #65740, #90160, .T. ) ; +#31781 = FILL_AREA_STYLE_COLOUR ( '', #94436 ) ; +#31782 = ORIENTED_EDGE ( 'NONE', *, *, #3099, .F. ) ; +#31783 = ORIENTED_EDGE ( 'NONE', *, *, #67745, .F. ) ; +#31784 = SURFACE_STYLE_FILL_AREA ( #16948 ) ; +#31785 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29359, 'distance_accuracy_value', 'NONE'); +#31786 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51516, 'distance_accuracy_value', 'NONE'); +#31787 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#31788 = SURFACE_SIDE_STYLE ('',( #78268 ) ) ; +#31789 = LINE ( 'NONE', #62968, #49807 ) ; +#31790 = SURFACE_STYLE_USAGE ( .BOTH. , #54808 ) ; +#31791 = FILL_AREA_STYLE ('',( #40486 ) ) ; +#31792 = STYLED_ITEM ( 'NONE', ( #47100 ), #20458 ) ; +#31793 = FILL_AREA_STYLE ('',( #7713 ) ) ; +#31794 = CARTESIAN_POINT ( 'NONE', ( 0.05696903375467490122, -1.121240070007210043, 0.8100000000000000533 ) ) ; +#31795 = PLANE ( 'NONE', #32567 ) ; +#31796 = SURFACE_STYLE_USAGE ( .BOTH. , #55805 ) ; +#31797 = ORIENTED_EDGE ( 'NONE', *, *, #62785, .T. ) ; +#31798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31799 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#31800 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80753, 'distance_accuracy_value', 'NONE'); +#31802 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95322 ), #88882 ) ; +#31801 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31803 = ORIENTED_EDGE ( 'NONE', *, *, #99459, .T. ) ; +#31804 = CARTESIAN_POINT ( 'NONE', ( 1.354915918613512682, -1.292011617012633451, 0.8099999999998060973 ) ) ; +#31805 = VECTOR ( 'NONE', #750, 1000.000000000000000 ) ; +#31806 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, 0.000000000000000000 ) ) ; +#31807 = EDGE_CURVE ( 'NONE', #75172, #88976, #3902, .T. ) ; +#31808 = VERTEX_POINT ( 'NONE', #81558 ) ; +#31809 = FACE_OUTER_BOUND ( 'NONE', #77167, .T. ) ; +#31810 = PLANE ( 'NONE', #53362 ) ; +#31811 = AXIS2_PLACEMENT_3D ( 'NONE', #87024, #40054, #30862 ) ; +#31812 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.000000000000000000 ) ) ; +#31813 = SURFACE_STYLE_FILL_AREA ( #657 ) ; +#31814 = ORIENTED_EDGE ( 'NONE', *, *, #38793, .T. ) ; +#31815 = VECTOR ( 'NONE', #71265, 1000.000000000000000 ) ; +#31816 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#31817 = VECTOR ( 'NONE', #22134, 1000.000000000000114 ) ; +#31818 = FILL_AREA_STYLE_COLOUR ( '', #65381 ) ; +#31819 = EDGE_CURVE ( 'NONE', #67009, #19702, #72860, .T. ) ; +#31820 = ORIENTED_EDGE ( 'NONE', *, *, #3865, .T. ) ; +#31821 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31822 = STYLED_ITEM ( 'NONE', ( #76655 ), #68519 ) ; +#31823 = SURFACE_SIDE_STYLE ('',( #70108 ) ) ; +#31824 = SURFACE_STYLE_FILL_AREA ( #17496 ) ; +#31825 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31826 = ORIENTED_EDGE ( 'NONE', *, *, #95999, .T. ) ; +#31827 = ORIENTED_EDGE ( 'NONE', *, *, #88034, .F. ) ; +#31828 = ORIENTED_EDGE ( 'NONE', *, *, #20548, .T. ) ; +#31829 = STYLED_ITEM ( 'NONE', ( #78210 ), #29627 ) ; +#31830 = VERTEX_POINT ( 'NONE', #88183 ) ; +#31832 = ORIENTED_EDGE ( 'NONE', *, *, #58285, .F. ) ; +#31831 = LINE ( 'NONE', #31326, #99703 ) ; +#31833 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31834 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13849 ), #8943 ) ; +#31836 = FACE_OUTER_BOUND ( 'NONE', #75701, .T. ) ; +#31835 = FILL_AREA_STYLE_COLOUR ( '', #64057 ) ; +#31837 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31838 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.000000000000000000 ) ) ; +#31839 = EDGE_LOOP ( 'NONE', ( #73675, #31678, #76687, #69240 ) ) ; +#31840 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#31841 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31842 = EDGE_LOOP ( 'NONE', ( #14909, #44615, #89261, #80460, #33292 ) ) ; +#31843 = AXIS2_PLACEMENT_3D ( 'NONE', #84555, #37620, #100758 ) ; +#31844 = SURFACE_SIDE_STYLE ('',( #94619 ) ) ; +#31845 = PLANE ( 'NONE', #30065 ) ; +#31846 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31847 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31848 = ORIENTED_EDGE ( 'NONE', *, *, #77367, .F. ) ; +#31851 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31850 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31849 = AXIS2_PLACEMENT_3D ( 'NONE', #66514, #19547, #3724 ) ; +#31852 = ORIENTED_EDGE ( 'NONE', *, *, #2901, .F. ) ; +#31853 = EDGE_CURVE ( 'NONE', #32633, #25280, #42227, .T. ) ; +#31854 = EDGE_CURVE ( 'NONE', #18285, #65640, #50418, .T. ) ; +#31856 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31855 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4699999999999999734, 0.000000000000000000 ) ) ; +#31857 = VECTOR ( 'NONE', #26581, 1000.000000000000000 ) ; +#31858 = SURFACE_SIDE_STYLE ('',( #70657 ) ) ; +#31859 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31860 = STYLED_ITEM ( 'NONE', ( #67440 ), #20692 ) ; +#31861 = ORIENTED_EDGE ( 'NONE', *, *, #68902, .T. ) ; +#31862 = PLANE ( 'NONE', #69897 ) ; +#31864 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31863 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#31865 = EDGE_CURVE ( 'NONE', #7273, #66120, #34072, .T. ) ; +#31866 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#31867 = EDGE_CURVE ( 'NONE', #65218, #68360, #65695, .T. ) ; +#31869 = VECTOR ( 'NONE', #90647, 1000.000000000000000 ) ; +#31868 = VECTOR ( 'NONE', #64884, 1000.000000000000000 ) ; +#31870 = VECTOR ( 'NONE', #53748, 1000.000000000000000 ) ; +#31871 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44193, 'distance_accuracy_value', 'NONE'); +#31872 = CARTESIAN_POINT ( 'NONE', ( -0.9449124846862100302, -1.010972591757870021, 0.8299999999999999600 ) ) ; +#31874 = ADVANCED_FACE ( 'NONE', ( #49369 ), #89184, .T. ) ; +#31873 = LINE ( 'NONE', #38528, #45780 ) ; +#31875 = SURFACE_STYLE_USAGE ( .BOTH. , #47697 ) ; +#31876 = STYLED_ITEM ( 'NONE', ( #86490 ), #4429 ) ; +#31877 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31878 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18826 ) ) ; +#31879 = LINE ( 'NONE', #63044, #11743 ) ; +#31880 = FILL_AREA_STYLE ('',( #16030 ) ) ; +#31881 = EDGE_LOOP ( 'NONE', ( #519, #53409, #2098, #53343 ) ) ; +#31882 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31886 = LINE ( 'NONE', #79365, #28114 ) ; +#31885 = FILL_AREA_STYLE_COLOUR ( '', #26189 ) ; +#31884 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#31887 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#31888 = AXIS2_PLACEMENT_3D ( 'NONE', #67485, #27231, #60393 ) ; +#31889 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31890 = FACE_OUTER_BOUND ( 'NONE', #19259, .T. ) ; +#31892 = EDGE_CURVE ( 'NONE', #81145, #69281, #34122, .T. ) ; +#31891 = AXIS2_PLACEMENT_3D ( 'NONE', #31062, #85681, #100865 ) ; +#31893 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31894 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31895 = PRESENTATION_STYLE_ASSIGNMENT (( #84993 ) ) ; +#31896 = VERTEX_POINT ( 'NONE', #82039 ) ; +#31897 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#31899 = ADVANCED_FACE ( 'NONE', ( #11980 ), #41224, .T. ) ; +#31898 = CYLINDRICAL_SURFACE ( 'NONE', #46137, 0.05000000000000002359 ) ; +#31900 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31901 = LINE ( 'NONE', #64066, #71345 ) ; +#31902 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8648700000000000276 ) ) ; +#31903 = FILL_AREA_STYLE ('',( #46699 ) ) ; +#31904 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31905 = FILL_AREA_STYLE_COLOUR ( '', #17464 ) ; +#31906 = PRESENTATION_STYLE_ASSIGNMENT (( #63072 ) ) ; +#31907 = FILL_AREA_STYLE_COLOUR ( '', #85911 ) ; +#31908 = FACE_OUTER_BOUND ( 'NONE', #45127, .T. ) ; +#31909 = ADVANCED_FACE ( 'NONE', ( #51894 ), #20219, .T. ) ; +#31910 = SURFACE_STYLE_FILL_AREA ( #7830 ) ; +#31911 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#31912 = SURFACE_STYLE_FILL_AREA ( #39070 ) ; +#31913 = EDGE_CURVE ( 'NONE', #17391, #42016, #28890, .T. ) ; +#31914 = LINE ( 'NONE', #25296, #63447 ) ; +#31915 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#31916 = EDGE_LOOP ( 'NONE', ( #29916, #63369, #66482, #22168 ) ) ; +#31917 = CYLINDRICAL_SURFACE ( 'NONE', #61117, 0.02999999999999997113 ) ; +#31918 = ORIENTED_EDGE ( 'NONE', *, *, #50241, .F. ) ; +#31919 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92902, 'distance_accuracy_value', 'NONE'); +#31920 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#31921 = CARTESIAN_POINT ( 'NONE', ( 0.2602800372128030171, -1.290215378870249952, 0.8300000000000009592 ) ) ; +#31922 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#31923 = VECTOR ( 'NONE', #87813, 1000.000000000000114 ) ; +#31924 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20461 ), #15552 ) ; +#31925 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#31926 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31927 = FACE_OUTER_BOUND ( 'NONE', #4560, .T. ) ; +#31928 = CARTESIAN_POINT ( 'NONE', ( -1.188831266068800074, -1.144973971495400145, 0.8100000000000000533 ) ) ; +#31929 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99275, #82550, #11996, #5876 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#31930 = ORIENTED_EDGE ( 'NONE', *, *, #50806, .F. ) ; +#31931 = PLANE ( 'NONE', #43860 ) ; +#31932 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61008, 'distance_accuracy_value', 'NONE'); +#31933 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59738 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15086, #31468, #31975 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31934 = STYLED_ITEM ( 'NONE', ( #29266 ), #89002 ) ; +#31935 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6226 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60970, #94458, #60478 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31936 = EDGE_LOOP ( 'NONE', ( #33983, #13085, #27117, #69104, #99131, #50126, #84561, #18780 ) ) ; +#31937 = PRESENTATION_STYLE_ASSIGNMENT (( #31423 ) ) ; +#31938 = SURFACE_STYLE_USAGE ( .BOTH. , #70213 ) ; +#31939 = EDGE_CURVE ( 'NONE', #83860, #90134, #21231, .T. ) ; +#31940 = STYLED_ITEM ( 'NONE', ( #35641 ), #77749 ) ; +#31941 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#31942 = PLANE ( 'NONE', #80020 ) ; +#31943 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31944 = ORIENTED_EDGE ( 'NONE', *, *, #44656, .T. ) ; +#31945 = FACE_OUTER_BOUND ( 'NONE', #67001, .T. ) ; +#31946 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93550, 'distance_accuracy_value', 'NONE'); +#31947 = AXIS2_PLACEMENT_3D ( 'NONE', #33191, #64329, #95435 ) ; +#31948 = PRESENTATION_STYLE_ASSIGNMENT (( #48305 ) ) ; +#31949 = VECTOR ( 'NONE', #42981, 1000.000000000000000 ) ; +#31950 = FILL_AREA_STYLE ('',( #94199 ) ) ; +#31951 = ADVANCED_FACE ( 'NONE', ( #61068 ), #22237, .T. ) ; +#31952 = ORIENTED_EDGE ( 'NONE', *, *, #38455, .T. ) ; +#31953 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71615 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77054, #17272, #30557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31954 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12334 ), #53170 ) ; +#31955 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#31956 = ORIENTED_EDGE ( 'NONE', *, *, #67500, .T. ) ; +#31957 = CARTESIAN_POINT ( 'NONE', ( 0.04624266161326810037, -1.451435312150680224, 0.8100000000000000533 ) ) ; +#31958 = EDGE_CURVE ( 'NONE', #58119, #14484, #15024, .T. ) ; +#31959 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31960 = SURFACE_SIDE_STYLE ('',( #70236 ) ) ; +#31961 = LINE ( 'NONE', #56986, #84040 ) ; +#31962 = VECTOR ( 'NONE', #26619, 1000.000000000000000 ) ; +#31963 = VECTOR ( 'NONE', #60742, 1000.000000000000000 ) ; +#31964 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #99056, #81007 ) ; +#31965 = ADVANCED_FACE ( 'NONE', ( #1267 ), #87048, .T. ) ; +#31966 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31967 = ORIENTED_EDGE ( 'NONE', *, *, #71386, .T. ) ; +#31968 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#31969 = PRESENTATION_STYLE_ASSIGNMENT (( #808 ) ) ; +#31970 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#31971 = EDGE_LOOP ( 'NONE', ( #72602, #452, #86436, #40506 ) ) ; +#31972 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01500000000000000291, -0.1400000000000000411 ) ) ; +#31973 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#31974 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#31975 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#31976 = ORIENTED_EDGE ( 'NONE', *, *, #60317, .T. ) ; +#31977 = VECTOR ( 'NONE', #47821, 1000.000000000000000 ) ; +#31978 = SURFACE_STYLE_USAGE ( .BOTH. , #80466 ) ; +#31979 = EDGE_LOOP ( 'NONE', ( #17334, #56378, #9295, #2, #44149, #9903, #3106, #23267, #90995, #17262, #24717, #58007, #99422, #71993, #88073, #75561, #76458 ) ) ; +#31980 = VERTEX_POINT ( 'NONE', #55924 ) ; +#31981 = EDGE_CURVE ( 'NONE', #55814, #42687, #48262, .T. ) ; +#31982 = SURFACE_STYLE_USAGE ( .BOTH. , #63145 ) ; +#31983 = LINE ( 'NONE', #31476, #6950 ) ; +#31984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22479 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15115, #15633, #32522 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#31985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#31986 = FACE_OUTER_BOUND ( 'NONE', #84967, .T. ) ; +#31987 = ORIENTED_EDGE ( 'NONE', *, *, #174, .F. ) ; +#31988 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#31989 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#31990 = AXIS2_PLACEMENT_3D ( 'NONE', #72185, #87009, #49218 ) ; +#31991 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#31992 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#31993 = ORIENTED_EDGE ( 'NONE', *, *, #15815, .F. ) ; +#31994 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#31995 = SURFACE_SIDE_STYLE ('',( #1352 ) ) ; +#31996 = ORIENTED_EDGE ( 'NONE', *, *, #63814, .T. ) ; +#31997 = EDGE_LOOP ( 'NONE', ( #97968, #28775, #17778, #40766 ) ) ; +#31998 = FILL_AREA_STYLE_COLOUR ( '', #75452 ) ; +#31999 = EDGE_CURVE ( 'NONE', #48055, #66870, #23759, .T. ) ; +#32000 = STYLED_ITEM ( 'NONE', ( #54770 ), #61573 ) ; +#32001 = PRESENTATION_STYLE_ASSIGNMENT (( #86620 ) ) ; +#32002 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32003 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18942 ), #64654 ) ; +#32004 = EDGE_CURVE ( 'NONE', #38134, #11144, #77865, .T. ) ; +#32005 = CARTESIAN_POINT ( 'NONE', ( -1.292955903404035656, -1.038601119630414127, 0.8099999999999598632 ) ) ; +#32006 = VECTOR ( 'NONE', #68745, 1000.000000000000114 ) ; +#32007 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#32008 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #43788 ) ; +#32009 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32010 = SURFACE_STYLE_FILL_AREA ( #70801 ) ; +#32011 = ORIENTED_EDGE ( 'NONE', *, *, #78867, .F. ) ; +#32012 = VECTOR ( 'NONE', #86592, 1000.000000000000000 ) ; +#32013 = VECTOR ( 'NONE', #60189, 1000.000000000000000 ) ; +#32014 = SURFACE_STYLE_USAGE ( .BOTH. , #86119 ) ; +#32015 = SURFACE_STYLE_USAGE ( .BOTH. , #64667 ) ; +#32016 = ADVANCED_FACE ( 'NONE', ( #38565 ), #62076, .T. ) ; +#32017 = CARTESIAN_POINT ( 'NONE', ( 1.676663961038960204, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#32018 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#32019 = LINE ( 'NONE', #95776, #50047 ) ; +#32020 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#32021 = ORIENTED_EDGE ( 'NONE', *, *, #56580, .T. ) ; +#32022 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77641 ), #43455 ) ; +#32023 = ADVANCED_FACE ( 'NONE', ( #73253 ), #88057, .T. ) ; +#32024 = SURFACE_STYLE_USAGE ( .BOTH. , #63688 ) ; +#32025 = SURFACE_SIDE_STYLE ('',( #40712 ) ) ; +#32026 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32027 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32028 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79047, 'distance_accuracy_value', 'NONE'); +#32029 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549970000000000070, 0.8648700000000000276 ) ) ; +#32030 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32031 = FILL_AREA_STYLE ('',( #25408 ) ) ; +#32032 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.000000000000000000 ) ) ; +#32033 = FILL_AREA_STYLE ('',( #55547 ) ) ; +#32034 = VECTOR ( 'NONE', #19669, 1000.000000000000000 ) ; +#32035 = ADVANCED_FACE ( 'NONE', ( #11360 ), #65559, .T. ) ; +#32036 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#32037 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#32038 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 1.100000000000000311, 0.000000000000000000 ) ) ; +#32039 = EDGE_CURVE ( 'NONE', #21501, #62602, #57957, .T. ) ; +#32040 = LINE ( 'NONE', #31021, #97423 ) ; +#32041 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79345 ) ) ; +#32043 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32042 = VECTOR ( 'NONE', #64494, 1000.000000000000000 ) ; +#32044 = FILL_AREA_STYLE_COLOUR ( '', #56909 ) ; +#32045 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #3873, 'design' ) ; +#32046 = SURFACE_SIDE_STYLE ('',( #94296 ) ) ; +#32047 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32048 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000001332, -0.2458578643762690530 ) ) ; +#32049 = ORIENTED_EDGE ( 'NONE', *, *, #99939, .F. ) ; +#32050 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32051 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666647068, -0.2999999999999999889, 3.495651678170021751E-76 ) ) ; +#32052 = PRESENTATION_STYLE_ASSIGNMENT (( #902 ) ) ; +#32053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100687, 'distance_accuracy_value', 'NONE'); +#32055 = FACE_OUTER_BOUND ( 'NONE', #21505, .T. ) ; +#32054 = CARTESIAN_POINT ( 'NONE', ( 0.01061219417860849966, -1.294636995308309890, 0.8300000000000002931 ) ) ; +#32056 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13512 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90387, #97531, #42451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32057 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32058 = CARTESIAN_POINT ( 'NONE', ( 1.103789355811249484, -1.122836816814991145, 0.8099999999999126787 ) ) ; +#32059 = FILL_AREA_STYLE_COLOUR ( '', #55916 ) ; +#32060 = DIRECTION ( 'NONE', ( -0.7071064476869689530, 0.7071071146859689849, 0.000000000000000000 ) ) ; +#32061 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17311 ) ) ; +#32062 = ADVANCED_FACE ( 'NONE', ( #95164 ), #77609, .T. ) ; +#32063 = ORIENTED_EDGE ( 'NONE', *, *, #92590, .F. ) ; +#32064 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#32065 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000089, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#32066 = FACE_OUTER_BOUND ( 'NONE', #59778, .T. ) ; +#32067 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9962, 'distance_accuracy_value', 'NONE'); +#32068 = VECTOR ( 'NONE', #9081, 1000.000000000000000 ) ; +#32069 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26350, 'distance_accuracy_value', 'NONE'); +#32070 = LINE ( 'NONE', #57602, #100597 ) ; +#32071 = EDGE_CURVE ( 'NONE', #15159, #48182, #20890, .T. ) ; +#32072 = AXIS2_PLACEMENT_3D ( 'NONE', #57175, #89299, #66800 ) ; +#32073 = VERTEX_POINT ( 'NONE', #63339 ) ; +#32075 = VERTEX_POINT ( 'NONE', #39822 ) ; +#32074 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32076 = ORIENTED_EDGE ( 'NONE', *, *, #88361, .T. ) ; +#32077 = CARTESIAN_POINT ( 'NONE', ( 0.2924145224725209768, -0.9822800159449730506, 0.8299999999999996270 ) ) ; +#32078 = ADVANCED_FACE ( 'NONE', ( #85261 ), #38812, .T. ) ; +#32079 = SURFACE_SIDE_STYLE ('',( #925 ) ) ; +#32080 = FILL_AREA_STYLE ('',( #95330 ) ) ; +#32081 = FILL_AREA_STYLE ('',( #86182 ) ) ; +#32082 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72830 ) ) ; +#32083 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #32341, #50239 ) ; +#32084 = LINE ( 'NONE', #79561, #91568 ) ; +#32085 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#32087 = ORIENTED_EDGE ( 'NONE', *, *, #41510, .T. ) ; +#32086 = ORIENTED_EDGE ( 'NONE', *, *, #97469, .T. ) ; +#32088 = ADVANCED_FACE ( 'NONE', ( #69932 ), #93396, .T. ) ; +#32089 = ORIENTED_EDGE ( 'NONE', *, *, #17238, .F. ) ; +#32090 = SURFACE_STYLE_USAGE ( .BOTH. , #8502 ) ; +#32091 = VECTOR ( 'NONE', #76979, 1000.000000000000000 ) ; +#32092 = VECTOR ( 'NONE', #76250, 1000.000000000000000 ) ; +#32093 = CARTESIAN_POINT ( 'NONE', ( 1.702237012380340087, -1.507644428662930025, 0.8100000000000000533 ) ) ; +#32095 = PRESENTATION_STYLE_ASSIGNMENT (( #54592 ) ) ; +#32094 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000000666, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#32096 = ORIENTED_EDGE ( 'NONE', *, *, #30584, .T. ) ; +#32097 = CLOSED_SHELL ( 'NONE', ( #54961, #76206, #98307, #39139, #85061, #33896 ) ) ; +#32099 = VECTOR ( 'NONE', #71833, 1000.000000000000000 ) ; +#32098 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#32100 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76107 ) ) ; +#32101 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32102 = ORIENTED_EDGE ( 'NONE', *, *, #32163, .F. ) ; +#32103 = FACE_OUTER_BOUND ( 'NONE', #91911, .T. ) ; +#32104 = ORIENTED_EDGE ( 'NONE', *, *, #97660, .F. ) ; +#32105 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #37467, #76745, #69044, #100118 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32107 = FACE_OUTER_BOUND ( 'NONE', #41524, .T. ) ; +#32106 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#32108 = STYLED_ITEM ( 'NONE', ( #97800 ), #5256 ) ; +#32109 = ORIENTED_EDGE ( 'NONE', *, *, #24774, .T. ) ; +#32110 = ADVANCED_FACE ( 'NONE', ( #88800 ), #100098, .F. ) ; +#32111 = ORIENTED_EDGE ( 'NONE', *, *, #31232, .F. ) ; +#32112 = EDGE_CURVE ( 'NONE', #83432, #20901, #67311, .T. ) ; +#32113 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999990008, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#32114 = SURFACE_SIDE_STYLE ('',( #93830 ) ) ; +#32115 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32116 = DIRECTION ( 'NONE', ( -0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#32117 = ORIENTED_EDGE ( 'NONE', *, *, #30658, .T. ) ; +#32118 = EDGE_CURVE ( 'NONE', #82605, #87124, #53521, .T. ) ; +#32119 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -1.300000000000000266, 0.000000000000000000 ) ) ; +#32120 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32121 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32122 = ORIENTED_EDGE ( 'NONE', *, *, #60923, .F. ) ; +#32124 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#32123 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#32125 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#32126 = ORIENTED_EDGE ( 'NONE', *, *, #26579, .T. ) ; +#32127 = ORIENTED_EDGE ( 'NONE', *, *, #82053, .T. ) ; +#32128 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32129 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32130 = ADVANCED_FACE ( 'NONE', ( #52025 ), #66814, .T. ) ; +#32131 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999989875, 0.000000000000000000 ) ) ; +#32132 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35436 ) ) ; +#32133 = EDGE_CURVE ( 'NONE', #40777, #65830, #29023, .T. ) ; +#32134 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32135 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#32136 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25532 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11698, #41950, #27646 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32137 = ORIENTED_EDGE ( 'NONE', *, *, #52798, .F. ) ; +#32138 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32139 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32140 = ORIENTED_EDGE ( 'NONE', *, *, #84777, .T. ) ; +#32141 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#32142 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32143 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#32144 = FILL_AREA_STYLE_COLOUR ( '', #79038 ) ; +#32145 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58270 ) ) ; +#32146 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8648700000000000276 ) ) ; +#32147 = CARTESIAN_POINT ( 'NONE', ( 1.783305012356700026, -1.001398657004090254, 0.8100000000000000533 ) ) ; +#32148 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32149 = LINE ( 'NONE', #71450, #78813 ) ; +#32150 = AXIS2_PLACEMENT_3D ( 'NONE', #18695, #71846, #18181 ) ; +#32151 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639962, -0.7000000000000009548, 3.495651678169978796E-76 ) ) ; +#32152 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#32153 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.4999999999999998890, 0.000000000000000000 ) ) ; +#32154 = FILL_AREA_STYLE_COLOUR ( '', #95220 ) ; +#32155 = LINE ( 'NONE', #17308, #5909 ) ; +#32156 = VECTOR ( 'NONE', #86375, 1000.000000000000000 ) ; +#32157 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#32158 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#32159 = VECTOR ( 'NONE', #1832, 1000.000000000000000 ) ; +#32160 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71023, #24604, #9153, #89359 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32161 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32162 = SURFACE_SIDE_STYLE ('',( #33165 ) ) ; +#32163 = EDGE_CURVE ( 'NONE', #50596, #74902, #20353, .T. ) ; +#32164 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32165 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32166 = STYLED_ITEM ( 'NONE', ( #28398 ), #40942 ) ; +#32167 = VECTOR ( 'NONE', #13265, 1000.000000000000000 ) ; +#32169 = EDGE_CURVE ( 'NONE', #4592, #16866, #28520, .T. ) ; +#32168 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99632, 'distance_accuracy_value', 'NONE'); +#32170 = VERTEX_POINT ( 'NONE', #44316 ) ; +#32171 = CLOSED_SHELL ( 'NONE', ( #97723, #73625, #8981, #30601, #75282, #42614 ) ) ; +#32172 = CARTESIAN_POINT ( 'NONE', ( -0.1238200612200840572, -3.099999999999980105, 0.000000000000000000 ) ) ; +#32173 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#32174 = ORIENTED_EDGE ( 'NONE', *, *, #79207, .F. ) ; +#32175 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.9000000000000019096, 0.8299999999999999600 ) ) ; +#32176 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32177 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32178 = VECTOR ( 'NONE', #45945, 1000.000000000000000 ) ; +#32179 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, 0.2999999999999999889 ) ) ; +#32180 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32181 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32182 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70824 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42987, #3184, #42003 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32183 = VECTOR ( 'NONE', #46393, 1000.000000000000000 ) ; +#32184 = ORIENTED_EDGE ( 'NONE', *, *, #80889, .F. ) ; +#32185 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32186 = EDGE_CURVE ( 'NONE', #48171, #100232, #81821, .T. ) ; +#32187 = EDGE_LOOP ( 'NONE', ( #43012, #10018, #71101, #71037 ) ) ; +#32188 = FACE_OUTER_BOUND ( 'NONE', #89264, .T. ) ; +#32189 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#32190 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#32191 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#32192 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#32193 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#32194 = PLANE ( 'NONE', #34837 ) ; +#32195 = VERTEX_POINT ( 'NONE', #91307 ) ; +#32196 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32197 = EDGE_CURVE ( 'NONE', #62344, #72400, #52500, .T. ) ; +#32198 = LINE ( 'NONE', #91945, #93324 ) ; +#32199 = ORIENTED_EDGE ( 'NONE', *, *, #88365, .T. ) ; +#32200 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#32201 = VERTEX_POINT ( 'NONE', #91791 ) ; +#32202 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48477 ), #15834 ) ; +#32203 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#32204 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#32205 = PRESENTATION_STYLE_ASSIGNMENT (( #8612 ) ) ; +#32206 = AXIS2_PLACEMENT_3D ( 'NONE', #94774, #46289, #86125 ) ; +#32207 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32208 = FILL_AREA_STYLE ('',( #80701 ) ) ; +#32209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32211 = ORIENTED_EDGE ( 'NONE', *, *, #35506, .F. ) ; +#32210 = ORIENTED_EDGE ( 'NONE', *, *, #4262, .T. ) ; +#32212 = ADVANCED_FACE ( 'NONE', ( #53021 ), #60206, .T. ) ; +#32213 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32214 = ORIENTED_EDGE ( 'NONE', *, *, #78018, .T. ) ; +#32215 = SURFACE_STYLE_FILL_AREA ( #71009 ) ; +#32216 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28903 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41592, #27789, #43073 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32217 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32218 = ORIENTED_EDGE ( 'NONE', *, *, #80394, .F. ) ; +#32219 = EDGE_CURVE ( 'NONE', #84177, #67856, #8974, .T. ) ; +#32220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58351 ) ) ; +#32221 = ORIENTED_EDGE ( 'NONE', *, *, #73945, .F. ) ; +#32222 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#32223 = SURFACE_STYLE_FILL_AREA ( #53188 ) ; +#32224 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#32225 = CARTESIAN_POINT ( 'NONE', ( -0.1401145506032289989, -0.9647878283071119609, 0.8300000000000000711 ) ) ; +#32226 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33845 ) ) ; +#32227 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32228 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#32229 = ORIENTED_EDGE ( 'NONE', *, *, #74539, .T. ) ; +#32230 = ORIENTED_EDGE ( 'NONE', *, *, #78746, .T. ) ; +#32231 = VERTEX_POINT ( 'NONE', #31541 ) ; +#32232 = ADVANCED_FACE ( 'NONE', ( #62700 ), #86149, .T. ) ; +#32233 = EDGE_CURVE ( 'NONE', #100106, #80334, #100835, .T. ) ; +#32234 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32235 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63226 ), #12613 ) ; +#32236 = VECTOR ( 'NONE', #7822, 1000.000000000000000 ) ; +#32237 = VECTOR ( 'NONE', #27034, 1000.000000000000000 ) ; +#32240 = EDGE_CURVE ( 'NONE', #62344, #100148, #30486, .T. ) ; +#32239 = ORIENTED_EDGE ( 'NONE', *, *, #15709, .F. ) ; +#32238 = FACE_OUTER_BOUND ( 'NONE', #25464, .T. ) ; +#32241 = EDGE_CURVE ( 'NONE', #45825, #80183, #70844, .T. ) ; +#32242 = LINE ( 'NONE', #31219, #62129 ) ; +#32243 = ORIENTED_EDGE ( 'NONE', *, *, #81482, .T. ) ; +#32244 = PLANE ( 'NONE', #1183 ) ; +#32245 = CLOSED_SHELL ( 'NONE', ( #77017, #99214, #79237, #22905, #12857, #4509 ) ) ; +#32246 = FACE_OUTER_BOUND ( 'NONE', #75886, .T. ) ; +#32247 = ORIENTED_EDGE ( 'NONE', *, *, #43385, .T. ) ; +#32248 = CARTESIAN_POINT ( 'NONE', ( -1.429289321881345387, 0.7100000000000001865, -0.8000000000000001554 ) ) ; +#32249 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21860 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81808, #13776, #43978 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32250 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32251 = EDGE_CURVE ( 'NONE', #20637, #57747, #63214, .T. ) ; +#32252 = FILL_AREA_STYLE ('',( #17896 ) ) ; +#32253 = FACE_OUTER_BOUND ( 'NONE', #39865, .T. ) ; +#32254 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.000000000000000000 ) ) ; +#32255 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61638 ) ) ; +#32257 = CARTESIAN_POINT ( 'NONE', ( 1.687860199445399889, -1.507611749840819915, 0.8299999999999999600 ) ) ; +#32256 = CARTESIAN_POINT ( 'NONE', ( -0.5056336073938946241, -1.178361975221479563, 0.8300000000000000711 ) ) ; +#32258 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#32259 = AXIS2_PLACEMENT_3D ( 'NONE', #88886, #68259, #3108 ) ; +#32260 = FILL_AREA_STYLE_COLOUR ( '', #53766 ) ; +#32261 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#32262 = VERTEX_POINT ( 'NONE', #94297 ) ; +#32263 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32264 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999999944, 0.1400000000000004297 ) ) ; +#32265 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32266 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2399999999999999634 ) ) ; +#32268 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#32267 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32269 = FACE_OUTER_BOUND ( 'NONE', #41071, .T. ) ; +#32270 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#32271 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#32272 = AXIS2_PLACEMENT_3D ( 'NONE', #95652, #42075, #80898 ) ; +#32273 = VERTEX_POINT ( 'NONE', #78006 ) ; +#32274 = FACE_OUTER_BOUND ( 'NONE', #90981, .T. ) ; +#32275 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#32276 = VERTEX_POINT ( 'NONE', #7958 ) ; +#32277 = VECTOR ( 'NONE', #57048, 1000.000000000000000 ) ; +#32279 = PLANE ( 'NONE', #64110 ) ; +#32278 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32280 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#32281 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20758 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33054, #18714, #49383 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32282 = LINE ( 'NONE', #94532, #39657 ) ; +#32284 = ADVANCED_FACE ( 'NONE', ( #39189 ), #76984, .T. ) ; +#32283 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82249, 'distance_accuracy_value', 'NONE'); +#32285 = EDGE_LOOP ( 'NONE', ( #45207, #24767, #73776, #82220 ) ) ; +#32286 = CARTESIAN_POINT ( 'NONE', ( 10.10135624974991053, 3.676137249749912961, 0.8648700000000000276 ) ) ; +#32287 = FILL_AREA_STYLE ('',( #77729 ) ) ; +#32288 = CARTESIAN_POINT ( 'NONE', ( -0.02773322717383189945, -1.124571705400470023, 0.8300000000000005151 ) ) ; +#32289 = LINE ( 'NONE', #48109, #74277 ) ; +#32290 = CARTESIAN_POINT ( 'NONE', ( 1.876179938779914957, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#32291 = FACE_OUTER_BOUND ( 'NONE', #28957, .T. ) ; +#32292 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32293 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32294 = VECTOR ( 'NONE', #94639, 1000.000000000000000 ) ; +#32295 = CARTESIAN_POINT ( 'NONE', ( -0.07453434150941770642, -0.9021709523542820186, 0.8100000000000000533 ) ) ; +#32296 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2932 ), #73044 ) ; +#32297 = LINE ( 'NONE', #48124, #83029 ) ; +#32298 = VECTOR ( 'NONE', #94290, 1000.000000000000000 ) ; +#32299 = ORIENTED_EDGE ( 'NONE', *, *, #98521, .T. ) ; +#32300 = FACE_OUTER_BOUND ( 'NONE', #58253, .T. ) ; +#32301 = ORIENTED_EDGE ( 'NONE', *, *, #16487, .T. ) ; +#32302 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32303 = SURFACE_STYLE_USAGE ( .BOTH. , #85907 ) ; +#32305 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32304 = FILL_AREA_STYLE_COLOUR ( '', #54763 ) ; +#32306 = CYLINDRICAL_SURFACE ( 'NONE', #54201, 0.009999999999999998473 ) ; +#32307 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32308 = CARTESIAN_POINT ( 'NONE', ( 0.002442604188005680164, -1.482878949593630091, 0.8300000000000004041 ) ) ; +#32309 = AXIS2_PLACEMENT_3D ( 'NONE', #16090, #8367, #39604 ) ; +#32310 = CARTESIAN_POINT ( 'NONE', ( 0.06988982237669021103, -1.070769809704489983, 0.8299999999999999600 ) ) ; +#32311 = FILL_AREA_STYLE_COLOUR ( '', #68947 ) ; +#32312 = CLOSED_SHELL ( 'NONE', ( #27713, #51428, #59252, #82035, #54405, #66810 ) ) ; +#32313 = VERTEX_POINT ( 'NONE', #71864 ) ; +#32314 = PLANE ( 'NONE', #78689 ) ; +#32315 = PLANE ( 'NONE', #23796 ) ; +#32316 = PRESENTATION_STYLE_ASSIGNMENT (( #1689 ) ) ; +#32317 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#32318 = ORIENTED_EDGE ( 'NONE', *, *, #70489, .F. ) ; +#32319 = FACE_OUTER_BOUND ( 'NONE', #23091, .T. ) ; +#32320 = FILL_AREA_STYLE ('',( #56344 ) ) ; +#32321 = ORIENTED_EDGE ( 'NONE', *, *, #50154, .T. ) ; +#32322 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43738 ) ) ; +#32323 = FILL_AREA_STYLE ('',( #78288 ) ) ; +#32324 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65962 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97426, #73983, #59208 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32325 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32326 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32327 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45323 ), #9428 ) ; +#32328 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -5.103411969279230082E-12 ) ) ; +#32329 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#32330 = LINE ( 'NONE', #24185, #39836 ) ; +#32331 = EDGE_LOOP ( 'NONE', ( #93487, #71109, #8488, #21165, #41693, #90491 ) ) ; +#32332 = SURFACE_STYLE_USAGE ( .BOTH. , #1166 ) ; +#32333 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32334 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32335 = FILL_AREA_STYLE ('',( #78299 ) ) ; +#32336 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25796 ), #24192 ) ; +#32337 = VERTEX_POINT ( 'NONE', #65196 ) ; +#32338 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#32339 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32340 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999996447, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#32341 = AXIS2_PLACEMENT_3D ( 'NONE', #29069, #60241, #90336 ) ; +#32342 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.000000000000000000 ) ) ; +#32343 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32344 = VECTOR ( 'NONE', #17885, 1000.000000000000114 ) ; +#32345 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#32346 = ORIENTED_EDGE ( 'NONE', *, *, #82874, .F. ) ; +#32348 = ORIENTED_EDGE ( 'NONE', *, *, #40314, .F. ) ; +#32347 = ORIENTED_EDGE ( 'NONE', *, *, #54950, .F. ) ; +#32349 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#32350 = ORIENTED_EDGE ( 'NONE', *, *, #27729, .T. ) ; +#32351 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32352 = ORIENTED_EDGE ( 'NONE', *, *, #38793, .F. ) ; +#32353 = STYLED_ITEM ( 'NONE', ( #82336 ), #56322 ) ; +#32355 = EDGE_LOOP ( 'NONE', ( #5043, #18243, #13706, #32491 ) ) ; +#32354 = PLANE ( 'NONE', #93293 ) ; +#32356 = EDGE_CURVE ( 'NONE', #54968, #63592, #19216, .T. ) ; +#32357 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32358 = FACE_OUTER_BOUND ( 'NONE', #33094, .T. ) ; +#32360 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1400000000000000411 ) ) ; +#32359 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.5000000000000000000, -13.15000000000000036 ) ) ; +#32361 = PLANE ( 'NONE', #79124 ) ; +#32362 = FILL_AREA_STYLE_COLOUR ( '', #47131 ) ; +#32363 = ORIENTED_EDGE ( 'NONE', *, *, #92435, .F. ) ; +#32364 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#32365 = LINE ( 'NONE', #48699, #56558 ) ; +#32366 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32367 = ORIENTED_EDGE ( 'NONE', *, *, #53440, .T. ) ; +#32368 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81295 ) ) ; +#32369 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000011380, -0.1499999999999999944 ) ) ; +#32370 = LINE ( 'NONE', #71671, #41850 ) ; +#32371 = ORIENTED_EDGE ( 'NONE', *, *, #97694, .T. ) ; +#32372 = VECTOR ( 'NONE', #78706, 1000.000000000000000 ) ; +#32373 = ORIENTED_EDGE ( 'NONE', *, *, #86992, .F. ) ; +#32374 = CARTESIAN_POINT ( 'NONE', ( 6.728456872965259628, 10.75427687296526003, 0.8991599999999999593 ) ) ; +#32375 = EDGE_CURVE ( 'NONE', #69034, #36383, #88677, .T. ) ; +#32376 = STYLED_ITEM ( 'NONE', ( #84231 ), #17586 ) ; +#32377 = PRESENTATION_STYLE_ASSIGNMENT (( #38513 ) ) ; +#32378 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.899999999999999911, 0.1829999999999539773 ) ) ; +#32379 = VECTOR ( 'NONE', #47317, 1000.000000000000000 ) ; +#32380 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#32381 = AXIS2_PLACEMENT_3D ( 'NONE', #95814, #19224, #88682 ) ; +#32382 = VECTOR ( 'NONE', #63869, 1000.000000000000000 ) ; +#32383 = VERTEX_POINT ( 'NONE', #9489 ) ; +#32384 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.383333333333326642, 0.000000000000000000 ) ) ; +#32385 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32386 = FACE_OUTER_BOUND ( 'NONE', #3231, .T. ) ; +#32387 = LINE ( 'NONE', #63548, #32294 ) ; +#32388 = FACE_OUTER_BOUND ( 'NONE', #51689, .T. ) ; +#32389 = CARTESIAN_POINT ( 'NONE', ( -0.9730827514092390551, -0.9588323859052130249, 0.8299999999999999600 ) ) ; +#32390 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#32391 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#32392 = FILL_AREA_STYLE_COLOUR ( '', #89524 ) ; +#32393 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#32394 = AXIS2_PLACEMENT_3D ( 'NONE', #57071, #18192, #34079 ) ; +#32395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32396 = VERTEX_POINT ( 'NONE', #95293 ) ; +#32397 = ADVANCED_FACE ( 'NONE', ( #95804 ), #72867, .T. ) ; +#32398 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32399 = VECTOR ( 'NONE', #74321, 1000.000000000000000 ) ; +#32400 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32401 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.676179938779915002, 0.000000000000000000 ) ) ; +#32402 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65532, 'distance_accuracy_value', 'NONE'); +#32403 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86165 ) ) ; +#32404 = CARTESIAN_POINT ( 'NONE', ( 2.583333333333333481, -3.099999999999960121, 0.000000000000000000 ) ) ; +#32405 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 1.076179938779915135, -0.02000000000000000042 ) ) ; +#32406 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32407 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#32408 = ADVANCED_FACE ( 'NONE', ( #42721 ), #73377, .T. ) ; +#32409 = ORIENTED_EDGE ( 'NONE', *, *, #70012, .F. ) ; +#32410 = CARTESIAN_POINT ( 'NONE', ( -2.499999999999999556, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#32411 = LINE ( 'NONE', #24780, #72271 ) ; +#32412 = SURFACE_STYLE_USAGE ( .BOTH. , #23745 ) ; +#32413 = SURFACE_STYLE_USAGE ( .BOTH. , #40071 ) ; +#32414 = FILL_AREA_STYLE_COLOUR ( '', #28172 ) ; +#32415 = LINE ( 'NONE', #24270, #81214 ) ; +#32416 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#32417 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#32418 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#32419 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32420 = LINE ( 'NONE', #17070, #16415 ) ; +#32421 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32422 = DIRECTION ( 'NONE', ( -0.7071060119555152568, -0.7071075504167430026, 0.000000000000000000 ) ) ; +#32423 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54137 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90808, #28514, #37202 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32424 = FACE_OUTER_BOUND ( 'NONE', #26497, .T. ) ; +#32425 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32426 = LINE ( 'NONE', #10859, #25830 ) ; +#32427 = ORIENTED_EDGE ( 'NONE', *, *, #69998, .F. ) ; +#32428 = ORIENTED_EDGE ( 'NONE', *, *, #2235, .F. ) ; +#32429 = AXIS2_PLACEMENT_3D ( 'NONE', #43890, #4087, #73545 ) ; +#32430 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32431 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32432 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42207 ) ) ; +#32433 = CARTESIAN_POINT ( 'NONE', ( 0.2157961956640810364, -1.329502282602879948, 0.8100000000000000533 ) ) ; +#32434 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853420540, 1.551146575926970472, 0.8299999999999999600 ) ) ; +#32435 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32436 = SURFACE_STYLE_FILL_AREA ( #40606 ) ; +#32437 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#32438 = CARTESIAN_POINT ( 'NONE', ( -1.137533421400759970, -1.155903533527329996, 0.8100000000000000533 ) ) ; +#32439 = ORIENTED_EDGE ( 'NONE', *, *, #16568, .T. ) ; +#32440 = AXIS2_PLACEMENT_3D ( 'NONE', #83039, #98769, #28901 ) ; +#32442 = EDGE_CURVE ( 'NONE', #57051, #62116, #36591, .T. ) ; +#32441 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32443 = PRESENTATION_STYLE_ASSIGNMENT (( #47751 ) ) ; +#32445 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32444 = VECTOR ( 'NONE', #27515, 1000.000000000000000 ) ; +#32446 = ORIENTED_EDGE ( 'NONE', *, *, #40068, .F. ) ; +#32447 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32448 = ADVANCED_FACE ( 'NONE', ( #51903 ), #82048, .T. ) ; +#32449 = FILL_AREA_STYLE ('',( #87569 ) ) ; +#32450 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43871 ), #55275 ) ; +#32451 = FACE_OUTER_BOUND ( 'NONE', #79974, .T. ) ; +#32452 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19390 ) ) ; +#32453 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32454 = LINE ( 'NONE', #63613, #89754 ) ; +#32455 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.966666666666667007, 0.000000000000000000 ) ) ; +#32456 = ORIENTED_EDGE ( 'NONE', *, *, #64392, .F. ) ; +#32457 = FILL_AREA_STYLE_COLOUR ( '', #43225 ) ; +#32458 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48851, 'distance_accuracy_value', 'NONE'); +#32460 = CARTESIAN_POINT ( 'NONE', ( 1.864761241546880166, -1.121240070007210043, 0.8099999999999998312 ) ) ; +#32461 = ADVANCED_FACE ( 'NONE', ( #59598 ), #21737, .T. ) ; +#32462 = VERTEX_POINT ( 'NONE', #37088 ) ; +#32463 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32464 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602300000000035, 0.8991599999999999593 ) ) ; +#32465 = LINE ( 'NONE', #70746, #42646 ) ; +#32466 = ORIENTED_EDGE ( 'NONE', *, *, #88128, .F. ) ; +#32467 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.000000000000000000 ) ) ; +#32468 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32469 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32470 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#32471 = FILL_AREA_STYLE_COLOUR ( '', #71280 ) ; +#32472 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#32473 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65111 ), #17786 ) ; +#32474 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #32672, #73662 ) ; +#32475 = AXIS2_PLACEMENT_3D ( 'NONE', #67811, #1426, #54032 ) ; +#32476 = ORIENTED_EDGE ( 'NONE', *, *, #83697, .F. ) ; +#32477 = EDGE_LOOP ( 'NONE', ( #60274, #2326, #31195, #10487 ) ) ; +#32478 = EDGE_CURVE ( 'NONE', #17365, #47739, #15928, .T. ) ; +#32479 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75175, 'distance_accuracy_value', 'NONE'); +#32480 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32482 = SURFACE_SIDE_STYLE ('',( #46752 ) ) ; +#32481 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32483 = SURFACE_STYLE_USAGE ( .BOTH. , #71786 ) ; +#32484 = ORIENTED_EDGE ( 'NONE', *, *, #12138, .F. ) ; +#32485 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#32486 = LINE ( 'NONE', #60879, #19685 ) ; +#32487 = LINE ( 'NONE', #49835, #34924 ) ; +#32488 = SURFACE_STYLE_FILL_AREA ( #96740 ) ; +#32489 = AXIS2_PLACEMENT_3D ( 'NONE', #769, #92178, #38077 ) ; +#32491 = ORIENTED_EDGE ( 'NONE', *, *, #73402, .T. ) ; +#32490 = VECTOR ( 'NONE', #71273, 1000.000000000000000 ) ; +#32493 = PLANE ( 'NONE', #48578 ) ; +#32492 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#32494 = ORIENTED_EDGE ( 'NONE', *, *, #58655, .T. ) ; +#32495 = ORIENTED_EDGE ( 'NONE', *, *, #41962, .T. ) ; +#32496 = CARTESIAN_POINT ( 'NONE', ( 8.800278999999999741, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#32497 = ADVANCED_FACE ( 'NONE', ( #13506 ), #99267, .T. ) ; +#32498 = VECTOR ( 'NONE', #83529, 1000.000000000000000 ) ; +#32500 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32499 = PLANE ( 'NONE', #11987 ) ; +#32501 = FILL_AREA_STYLE_COLOUR ( '', #8109 ) ; +#32502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32503 = ORIENTED_EDGE ( 'NONE', *, *, #27763, .T. ) ; +#32504 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9286, #25714, #18001 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32505 = FILL_AREA_STYLE ('',( #38631 ) ) ; +#32506 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83005 ), #35727 ) ; +#32507 = STYLED_ITEM ( 'NONE', ( #2798 ), #91918 ) ; +#32508 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32509 = ORIENTED_EDGE ( 'NONE', *, *, #50026, .T. ) ; +#32510 = CARTESIAN_POINT ( 'NONE', ( 1.261158141153259971, -1.441583773770549914, 0.8299999999999999600 ) ) ; +#32511 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#32512 = ORIENTED_EDGE ( 'NONE', *, *, #73067, .F. ) ; +#32513 = ORIENTED_EDGE ( 'NONE', *, *, #74539, .F. ) ; +#32515 = FILL_AREA_STYLE ('',( #70787 ) ) ; +#32514 = STYLED_ITEM ( 'NONE', ( #42225 ), #81071 ) ; +#32516 = SURFACE_STYLE_FILL_AREA ( #55511 ) ; +#32518 = VECTOR ( 'NONE', #41643, 1000.000000000000000 ) ; +#32517 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32519 = VECTOR ( 'NONE', #19771, 1000.000000000000000 ) ; +#32520 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.383333333333323090, 1.747825839084783216E-76 ) ) ; +#32521 = VECTOR ( 'NONE', #39048, 1000.000000000000000 ) ; +#32522 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32523 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#32524 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51954, #83085, #62135, #54966 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32525 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#32526 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#32527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32528 = FILL_AREA_STYLE ('',( #39661 ) ) ; +#32529 = ORIENTED_EDGE ( 'NONE', *, *, #95571, .T. ) ; +#32530 = EDGE_CURVE ( 'NONE', #73910, #73267, #77358, .T. ) ; +#32531 = VECTOR ( 'NONE', #39955, 1000.000000000000000 ) ; +#32532 = CARTESIAN_POINT ( 'NONE', ( 1.291611456110860034, -1.433733517242619993, 0.8299999999999994049 ) ) ; +#32533 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21079 ), #66753 ) ; +#32535 = SURFACE_SIDE_STYLE ('',( #80006 ) ) ; +#32534 = FACE_OUTER_BOUND ( 'NONE', #50463, .T. ) ; +#32536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32537 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#32538 = VECTOR ( 'NONE', #10964, 999.9999999999998863 ) ; +#32539 = PLANE ( 'NONE', #78083 ) ; +#32540 = AXIS2_PLACEMENT_3D ( 'NONE', #91750, #21828, #53487 ) ; +#32541 = CARTESIAN_POINT ( 'NONE', ( 1.988871258640574791, 1.449466043945983884, -11.37855895647839866 ) ) ; +#32542 = SURFACE_SIDE_STYLE ('',( #96285 ) ) ; +#32543 = ADVANCED_FACE ( 'NONE', ( #267 ), #22756, .T. ) ; +#32544 = ORIENTED_EDGE ( 'NONE', *, *, #87442, .T. ) ; +#32545 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32547 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72163, 'distance_accuracy_value', 'NONE'); +#32546 = SURFACE_STYLE_USAGE ( .BOTH. , #33554 ) ; +#32548 = PRESENTATION_STYLE_ASSIGNMENT (( #48874 ) ) ; +#32549 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32550 = EDGE_CURVE ( 'NONE', #93901, #95742, #6830, .T. ) ; +#32551 = DIRECTION ( 'NONE', ( 0.7071060119555145906, -0.7071075504167435577, 0.000000000000000000 ) ) ; +#32552 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32553 = SURFACE_STYLE_FILL_AREA ( #32031 ) ; +#32554 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#32555 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#32556 = SURFACE_SIDE_STYLE ('',( #63706 ) ) ; +#32557 = LINE ( 'NONE', #64197, #52050 ) ; +#32558 = PLANE ( 'NONE', #50389 ) ; +#32559 = PRESENTATION_STYLE_ASSIGNMENT (( #56050 ) ) ; +#32560 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34179 ) ) ; +#32561 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32562 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32563 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.008431457505076187312, -0.2458578643762690530 ) ) ; +#32564 = ORIENTED_EDGE ( 'NONE', *, *, #30293, .F. ) ; +#32565 = SURFACE_STYLE_FILL_AREA ( #86672 ) ; +#32566 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#32567 = AXIS2_PLACEMENT_3D ( 'NONE', #70076, #14414, #62973 ) ; +#32568 = CARTESIAN_POINT ( 'NONE', ( 0.01352834099273039943, -1.306448053922619978, 0.8300000000000002931 ) ) ; +#32569 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32570 = EDGE_CURVE ( 'NONE', #91484, #80171, #69164, .T. ) ; +#32571 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32572 = FACE_OUTER_BOUND ( 'NONE', #12303, .T. ) ; +#32573 = ORIENTED_EDGE ( 'NONE', *, *, #48164, .T. ) ; +#32574 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32575 = LINE ( 'NONE', #46336, #69017 ) ; +#32576 = AXIS2_PLACEMENT_3D ( 'NONE', #24163, #32307, #25181 ) ; +#32577 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32578 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4808578643762691507, 0.2500000000000001110 ) ) ; +#32579 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32580 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73330 ), #78203 ) ; +#32581 = EDGE_CURVE ( 'NONE', #78282, #43535, #70715, .T. ) ; +#32582 = ORIENTED_EDGE ( 'NONE', *, *, #10628, .T. ) ; +#32583 = ORIENTED_EDGE ( 'NONE', *, *, #90777, .F. ) ; +#32584 = EDGE_CURVE ( 'NONE', #17633, #97358, #39581, .T. ) ; +#32585 = LINE ( 'NONE', #62229, #58564 ) ; +#32586 = ORIENTED_EDGE ( 'NONE', *, *, #3683, .T. ) ; +#32587 = SURFACE_SIDE_STYLE ('',( #57097 ) ) ; +#32588 = ADVANCED_FACE ( 'NONE', ( #31927 ), #53895, .F. ) ; +#32589 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#32590 = SURFACE_STYLE_USAGE ( .BOTH. , #65747 ) ; +#32591 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32592 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#32593 = SHAPE_DEFINITION_REPRESENTATION ( #56532, #78202 ) ; +#32594 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#32595 = CARTESIAN_POINT ( 'NONE', ( 1.020574219067895028, -1.452480241729798172, 0.8099999999997055111 ) ) ; +#32596 = VECTOR ( 'NONE', #8297, 1000.000000000000000 ) ; +#32598 = ORIENTED_EDGE ( 'NONE', *, *, #99459, .F. ) ; +#32597 = ORIENTED_EDGE ( 'NONE', *, *, #31153, .T. ) ; +#32599 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14599 ) ) ; +#32600 = ORIENTED_EDGE ( 'NONE', *, *, #99786, .T. ) ; +#32601 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#32602 = EDGE_CURVE ( 'NONE', #93440, #76054, #40096, .T. ) ; +#32603 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46422, 'distance_accuracy_value', 'NONE'); +#32604 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32606 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8099999999999438760 ) ) ; +#32605 = SURFACE_SIDE_STYLE ('',( #96353 ) ) ; +#32607 = ORIENTED_EDGE ( 'NONE', *, *, #54902, .T. ) ; +#32608 = LINE ( 'NONE', #51956, #2644 ) ; +#32609 = EDGE_CURVE ( 'NONE', #84202, #77948, #71225, .T. ) ; +#32610 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32611 = AXIS2_PLACEMENT_3D ( 'NONE', #39869, #37, #62364 ) ; +#32612 = ORIENTED_EDGE ( 'NONE', *, *, #67912, .F. ) ; +#32613 = VECTOR ( 'NONE', #96923, 1000.000000000000000 ) ; +#32614 = EDGE_LOOP ( 'NONE', ( #36201, #10085, #45430, #2874 ) ) ; +#32616 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32615 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32617 = EDGE_LOOP ( 'NONE', ( #53289, #82184, #78800, #39587 ) ) ; +#32618 = ORIENTED_EDGE ( 'NONE', *, *, #48828, .T. ) ; +#32619 = STYLED_ITEM ( 'NONE', ( #31025 ), #9801 ) ; +#32620 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8991599999999999593 ) ) ; +#32621 = ADVANCED_FACE ( 'NONE', ( #25795 ), #50307, .T. ) ; +#32622 = FILL_AREA_STYLE_COLOUR ( '', #80457 ) ; +#32623 = EDGE_CURVE ( 'NONE', #25572, #20028, #18072, .T. ) ; +#32626 = ORIENTED_EDGE ( 'NONE', *, *, #71781, .T. ) ; +#32625 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55458 ), #48955 ) ; +#32624 = PRESENTATION_STYLE_ASSIGNMENT (( #56634 ) ) ; +#32627 = PLANE ( 'NONE', #1834 ) ; +#32628 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#32629 = ORIENTED_EDGE ( 'NONE', *, *, #8959, .F. ) ; +#32630 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30831, #13429, #52828, #92589 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32631 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#32632 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#32633 = VERTEX_POINT ( 'NONE', #64086 ) ; +#32634 = ORIENTED_EDGE ( 'NONE', *, *, #64699, .T. ) ; +#32636 = LINE ( 'NONE', #10537, #42223 ) ; +#32635 = PRESENTATION_STYLE_ASSIGNMENT (( #56126 ) ) ; +#32637 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32638 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43210 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28173, #12766, #34853 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32639 = CARTESIAN_POINT ( 'NONE', ( -0.4538159765161179915, -1.241081418093670008, 0.8100000000000000533 ) ) ; +#32640 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.700000000000000178, 0.1829999999999460114 ) ) ; +#32641 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#32642 = VECTOR ( 'NONE', #49846, 1000.000000000000000 ) ; +#32643 = VECTOR ( 'NONE', #83607, 1000.000000000000000 ) ; +#32644 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89064, 'distance_accuracy_value', 'NONE'); +#32645 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#32646 = ORIENTED_EDGE ( 'NONE', *, *, #62435, .F. ) ; +#32647 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8100000000000000533 ) ) ; +#32648 = EDGE_CURVE ( 'NONE', #29149, #19588, #80933, .T. ) ; +#32649 = ORIENTED_EDGE ( 'NONE', *, *, #69536, .F. ) ; +#32651 = SURFACE_STYLE_USAGE ( .BOTH. , #48485 ) ; +#32650 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35935 ), #39112 ) ; +#32652 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43999 ), #100925 ) ; +#32653 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#32654 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#32655 = FACE_OUTER_BOUND ( 'NONE', #74059, .T. ) ; +#32657 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32656 = AXIS2_PLACEMENT_3D ( 'NONE', #46482, #92440, #86830 ) ; +#32658 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999749605 ) ) ; +#32659 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32660 = SURFACE_STYLE_USAGE ( .BOTH. , #70947 ) ; +#32661 = EDGE_CURVE ( 'NONE', #25465, #31830, #57450, .T. ) ; +#32662 = VECTOR ( 'NONE', #80835, 1000.000000000000000 ) ; +#32663 = CARTESIAN_POINT ( 'NONE', ( 1.662784497387987948, -1.164919038798193585, 0.8166666666666666519 ) ) ; +#32664 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32665 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32666 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#32667 = PRESENTATION_STYLE_ASSIGNMENT (( #2526 ) ) ; +#32668 = VECTOR ( 'NONE', #7926, 1000.000000000000000 ) ; +#32669 = DIRECTION ( 'NONE', ( -1.425188158846549879E-32, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#32670 = SURFACE_STYLE_USAGE ( .BOTH. , #10077 ) ; +#32671 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852913999999999728, 0.8648700000000000276 ) ) ; +#32672 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #78202, #98962 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #94714 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#32673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32674 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32675 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32676 = VECTOR ( 'NONE', #15412, 1000.000000000000000 ) ; +#32677 = ORIENTED_EDGE ( 'NONE', *, *, #15309, .F. ) ; +#32678 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32679 = SURFACE_STYLE_USAGE ( .BOTH. , #2030 ) ; +#32680 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22201, 'distance_accuracy_value', 'NONE'); +#32681 = ORIENTED_EDGE ( 'NONE', *, *, #86355, .T. ) ; +#32682 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57700, 'distance_accuracy_value', 'NONE'); +#32683 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#32684 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#32685 = AXIS2_PLACEMENT_3D ( 'NONE', #8447, #70830, #885 ) ; +#32686 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32688 = ADVANCED_FACE ( 'NONE', ( #2802 ), #89078, .T. ) ; +#32687 = VECTOR ( 'NONE', #69156, 1000.000000000000000 ) ; +#32689 = ORIENTED_EDGE ( 'NONE', *, *, #6520, .F. ) ; +#32690 = ORIENTED_EDGE ( 'NONE', *, *, #60600, .F. ) ; +#32691 = SURFACE_STYLE_USAGE ( .BOTH. , #15293 ) ; +#32692 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20367, 'distance_accuracy_value', 'NONE'); +#32693 = VECTOR ( 'NONE', #65978, 1000.000000000000000 ) ; +#32694 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#32695 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#32696 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#32697 = SURFACE_STYLE_USAGE ( .BOTH. , #71491 ) ; +#32698 = SURFACE_STYLE_USAGE ( .BOTH. , #517 ) ; +#32699 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32700 = ORIENTED_EDGE ( 'NONE', *, *, #37808, .F. ) ; +#32701 = CARTESIAN_POINT ( 'NONE', ( 1.062208424706029941, -1.030374455384980070, 0.8300000000000002931 ) ) ; +#32702 = ORIENTED_EDGE ( 'NONE', *, *, #62047, .T. ) ; +#32703 = SURFACE_STYLE_FILL_AREA ( #16827 ) ; +#32704 = EDGE_CURVE ( 'NONE', #29928, #59654, #19102, .T. ) ; +#32705 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41258 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1356, #57022, #25865 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32706 = VECTOR ( 'NONE', #22768, 1000.000000000000114 ) ; +#32707 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#32708 = ORIENTED_EDGE ( 'NONE', *, *, #60679, .F. ) ; +#32709 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#32710 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, -0.2999999999999999889, 0.1829999999999709914 ) ) ; +#32711 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#32712 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32713 = LINE ( 'NONE', #25566, #3916 ) ; +#32714 = VECTOR ( 'NONE', #31349, 1000.000000000000000 ) ; +#32715 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, 0.000000000000000000 ) ) ; +#32716 = AXIS2_PLACEMENT_3D ( 'NONE', #28882, #83523, #29873 ) ; +#32717 = DIRECTION ( 'NONE', ( -1.836909530733570078E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32718 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#32720 = ORIENTED_EDGE ( 'NONE', *, *, #87672, .T. ) ; +#32719 = EDGE_LOOP ( 'NONE', ( #91423, #16336, #96252, #173 ) ) ; +#32722 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#32721 = STYLED_ITEM ( 'NONE', ( #4471 ), #57674 ) ; +#32723 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#32724 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52189, #97093, #4197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32725 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32726 = ORIENTED_EDGE ( 'NONE', *, *, #7541, .F. ) ; +#32727 = FILL_AREA_STYLE_COLOUR ( '', #98120 ) ; +#32728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76712 ), #13022 ) ; +#32730 = CARTESIAN_POINT ( 'NONE', ( 8.665929499499824828, 3.159949499499825620, 0.8991599999999999593 ) ) ; +#32729 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32731 = VERTEX_POINT ( 'NONE', #55934 ) ; +#32732 = ORIENTED_EDGE ( 'NONE', *, *, #43758, .F. ) ; +#32733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66966 ) ) ; +#32734 = LINE ( 'NONE', #49568, #27004 ) ; +#32735 = PRESENTATION_STYLE_ASSIGNMENT (( #23558 ) ) ; +#32736 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109697000000000600, 0.8648700000000000276 ) ) ; +#32737 = PLANE ( 'NONE', #44966 ) ; +#32738 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, -3.149999999999979927, 0.000000000000000000 ) ) ; +#32739 = ORIENTED_EDGE ( 'NONE', *, *, #12221, .F. ) ; +#32740 = ORIENTED_EDGE ( 'NONE', *, *, #53715, .F. ) ; +#32741 = FILL_AREA_STYLE ('',( #94980 ) ) ; +#32742 = ORIENTED_EDGE ( 'NONE', *, *, #69193, .T. ) ; +#32743 = EDGE_CURVE ( 'NONE', #82440, #81837, #34471, .T. ) ; +#32744 = VECTOR ( 'NONE', #29215, 1000.000000000000000 ) ; +#32746 = EDGE_LOOP ( 'NONE', ( #20887, #77179, #82966, #27016 ) ) ; +#32745 = SURFACE_STYLE_FILL_AREA ( #49581 ) ; +#32747 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32748 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32749 = ORIENTED_EDGE ( 'NONE', *, *, #61971, .T. ) ; +#32750 = FACE_OUTER_BOUND ( 'NONE', #75663, .T. ) ; +#32751 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#32752 = ORIENTED_EDGE ( 'NONE', *, *, #67334, .T. ) ; +#32753 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32754 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32755 = DIRECTION ( 'NONE', ( 1.000000000000000000, 2.385832768178450048E-26, 3.399536532815460200E-14 ) ) ; +#32756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58874, #28198, #90467 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32757 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#32758 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#32759 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8648700000000000276 ) ) ; +#32760 = CARTESIAN_POINT ( 'NONE', ( 1.612727879620370119, -1.495500525511030077, 0.8099999999999982769 ) ) ; +#32761 = EDGE_CURVE ( 'NONE', #31723, #2319, #90061, .T. ) ; +#32762 = SURFACE_SIDE_STYLE ('',( #55748 ) ) ; +#32763 = ORIENTED_EDGE ( 'NONE', *, *, #38653, .T. ) ; +#32764 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#32766 = SURFACE_SIDE_STYLE ('',( #71576 ) ) ; +#32765 = SURFACE_STYLE_FILL_AREA ( #85872 ) ; +#32767 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000032419, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#32769 = EDGE_CURVE ( 'NONE', #13041, #96910, #28773, .T. ) ; +#32768 = SURFACE_STYLE_FILL_AREA ( #41449 ) ; +#32770 = AXIS2_PLACEMENT_3D ( 'NONE', #89021, #81390, #73211 ) ; +#32771 = AXIS2_PLACEMENT_3D ( 'NONE', #100132, #30789, #85929 ) ; +#32772 = PRESENTATION_STYLE_ASSIGNMENT (( #87894 ) ) ; +#32773 = SURFACE_SIDE_STYLE ('',( #48097 ) ) ; +#32774 = ORIENTED_EDGE ( 'NONE', *, *, #70545, .F. ) ; +#32775 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32776 = EDGE_CURVE ( 'NONE', #50788, #43767, #71686, .T. ) ; +#32777 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86586 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20167, #41679, #50374 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32778 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#32779 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#32780 = VECTOR ( 'NONE', #1764, 1000.000000000000000 ) ; +#32781 = SURFACE_STYLE_USAGE ( .BOTH. , #80269 ) ; +#32782 = EDGE_CURVE ( 'NONE', #98821, #91854, #90572, .T. ) ; +#32783 = ORIENTED_EDGE ( 'NONE', *, *, #14653, .T. ) ; +#32784 = LINE ( 'NONE', #24140, #45656 ) ; +#32785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70305 ) ) ; +#32786 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32787 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373192999999999664, 0.8991599999999999593 ) ) ; +#32788 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32789 = LINE ( 'NONE', #49638, #94213 ) ; +#32790 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.05000000000000071, 0.000000000000000000 ) ) ; +#32791 = CIRCLE ( 'NONE', #37686, 0.09999999999999939493 ) ; +#32792 = PLANE ( 'NONE', #26327 ) ; +#32793 = EDGE_CURVE ( 'NONE', #17257, #17507, #35974, .T. ) ; +#32794 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16879, 'distance_accuracy_value', 'NONE'); +#32796 = EDGE_CURVE ( 'NONE', #52114, #93672, #51283, .T. ) ; +#32797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24667 ) ) ; +#32798 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#32799 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55639 ), #52416 ) ; +#32800 = ORIENTED_EDGE ( 'NONE', *, *, #63157, .T. ) ; +#32801 = LINE ( 'NONE', #64452, #95393 ) ; +#32802 = VERTEX_POINT ( 'NONE', #51783 ) ; +#32803 = PRESENTATION_STYLE_ASSIGNMENT (( #55309 ) ) ; +#32805 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33568, 'distance_accuracy_value', 'NONE'); +#32804 = VECTOR ( 'NONE', #95491, 1000.000000000000000 ) ; +#32806 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94612, 'distance_accuracy_value', 'NONE'); +#32807 = EDGE_CURVE ( 'NONE', #90613, #64246, #9726, .T. ) ; +#32808 = EDGE_CURVE ( 'NONE', #43148, #1595, #52293, .T. ) ; +#32809 = SURFACE_STYLE_FILL_AREA ( #38954 ) ; +#32810 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#32811 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#32812 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#32813 = CARTESIAN_POINT ( 'NONE', ( 0.06941959667897069919, -1.084027901463999966, 0.8299999999999999600 ) ) ; +#32814 = SURFACE_SIDE_STYLE ('',( #73130 ) ) ; +#32815 = ORIENTED_EDGE ( 'NONE', *, *, #24142, .F. ) ; +#32816 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32817 = PRESENTATION_STYLE_ASSIGNMENT (( #1688 ) ) ; +#32818 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32819 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43063, 'distance_accuracy_value', 'NONE'); +#32820 = LINE ( 'NONE', #11243, #78561 ) ; +#32821 = ORIENTED_EDGE ( 'NONE', *, *, #65737, .T. ) ; +#32822 = CARTESIAN_POINT ( 'NONE', ( 1.217910621008780891, -1.229126379814544645, 0.8099999999998457323 ) ) ; +#32823 = EDGE_CURVE ( 'NONE', #63293, #60955, #13906, .T. ) ; +#32824 = ORIENTED_EDGE ( 'NONE', *, *, #94579, .T. ) ; +#32825 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #151 ), #89877 ) ; +#32826 = VECTOR ( 'NONE', #72511, 1000.000000000000000 ) ; +#32827 = SURFACE_SIDE_STYLE ('',( #62476 ) ) ; +#32828 = EDGE_CURVE ( 'NONE', #69223, #99969, #28294, .T. ) ; +#32829 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32830 = FACE_OUTER_BOUND ( 'NONE', #50841, .T. ) ; +#32831 = ORIENTED_EDGE ( 'NONE', *, *, #12779, .F. ) ; +#32832 = ORIENTED_EDGE ( 'NONE', *, *, #30229, .F. ) ; +#32833 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#32834 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8299999999999999600 ) ) ; +#32835 = ORIENTED_EDGE ( 'NONE', *, *, #12078, .F. ) ; +#32836 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #54219, #54747, #15371, #22051 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32837 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32838 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#32839 = CARTESIAN_POINT ( 'NONE', ( 1.776971753240009999, -0.9939892240680031632, 0.8300000000000004041 ) ) ; +#32840 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26370 ), #3554 ) ; +#32841 = VECTOR ( 'NONE', #77141, 1000.000000000000114 ) ; +#32842 = PRESENTATION_STYLE_ASSIGNMENT (( #1716 ) ) ; +#32843 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#32844 = CARTESIAN_POINT ( 'NONE', ( 1.496131215532870096, -1.321596304865350069, 0.8300000000000001821 ) ) ; +#32845 = VERTEX_POINT ( 'NONE', #99145 ) ; +#32847 = VERTEX_POINT ( 'NONE', #13384 ) ; +#32846 = VERTEX_POINT ( 'NONE', #59476 ) ; +#32848 = FILL_AREA_STYLE_COLOUR ( '', #58058 ) ; +#32849 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100956 ) ; +#32850 = ORIENTED_EDGE ( 'NONE', *, *, #45482, .T. ) ; +#32851 = STYLED_ITEM ( 'NONE', ( #36400 ), #86521 ) ; +#32852 = FILL_AREA_STYLE_COLOUR ( '', #57336 ) ; +#32853 = STYLED_ITEM ( 'NONE', ( #28045 ), #95816 ) ; +#32854 = EDGE_CURVE ( 'NONE', #2574, #34606, #83911, .T. ) ; +#32855 = VERTEX_POINT ( 'NONE', #97679 ) ; +#32857 = VERTEX_POINT ( 'NONE', #12380 ) ; +#32856 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32858 = STYLED_ITEM ( 'NONE', ( #1879 ), #8154 ) ; +#32859 = STYLED_ITEM ( 'NONE', ( #20451 ), #94968 ) ; +#32860 = PRESENTATION_STYLE_ASSIGNMENT (( #79323 ) ) ; +#32862 = SURFACE_SIDE_STYLE ('',( #34889 ) ) ; +#32861 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32863 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32864 = EDGE_LOOP ( 'NONE', ( #22396, #92708, #310, #83038 ) ) ; +#32866 = ADVANCED_FACE ( 'NONE', ( #82920 ), #76239, .T. ) ; +#32865 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#32867 = ORIENTED_EDGE ( 'NONE', *, *, #51424, .F. ) ; +#32868 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41050 ) ) ; +#32869 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#32870 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#32871 = ORIENTED_EDGE ( 'NONE', *, *, #35579, .F. ) ; +#32872 = AXIS2_PLACEMENT_3D ( 'NONE', #86409, #40467, #71603 ) ; +#32873 = SURFACE_STYLE_FILL_AREA ( #86484 ) ; +#32874 = ORIENTED_EDGE ( 'NONE', *, *, #30584, .F. ) ; +#32875 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #10791, #48698, #42037, #65495 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#32876 = CARTESIAN_POINT ( 'NONE', ( 0.003128152952664109854, -1.177156496261070107, 0.8300000000000002931 ) ) ; +#32878 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#32877 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.100000000000000089, -0.02000000000000209943 ) ) ; +#32879 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32880 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.000000000000000000 ) ) ; +#32881 = VECTOR ( 'NONE', #40018, 1000.000000000000000 ) ; +#32882 = SURFACE_SIDE_STYLE ('',( #17523 ) ) ; +#32883 = ORIENTED_EDGE ( 'NONE', *, *, #69095, .F. ) ; +#32884 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32885 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59237 ), #20045 ) ; +#32886 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32888 = EDGE_CURVE ( 'NONE', #29072, #18396, #60465, .T. ) ; +#32887 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32889 = VECTOR ( 'NONE', #79390, 1000.000000000000000 ) ; +#32890 = CARTESIAN_POINT ( 'NONE', ( -1.050422986827179939, -0.9018902076549559776, 0.8299999999999999600 ) ) ; +#32891 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#32892 = VERTEX_POINT ( 'NONE', #6713 ) ; +#32893 = FACE_BOUND ( 'NONE', #31979, .T. ) ; +#32894 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81822 ) ) ; +#32895 = LINE ( 'NONE', #41074, #1478 ) ; +#32896 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32897 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#32898 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#32899 = ORIENTED_EDGE ( 'NONE', *, *, #90484, .T. ) ; +#32900 = FILL_AREA_STYLE ('',( #49232 ) ) ; +#32902 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32901 = SURFACE_SIDE_STYLE ('',( #25755 ) ) ; +#32903 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#32904 = VECTOR ( 'NONE', #91584, 1000.000000000000000 ) ; +#32905 = CARTESIAN_POINT ( 'NONE', ( 0.3455761866733689791, -1.312343239366150049, 0.8299999999999999600 ) ) ; +#32906 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#32907 = FILL_AREA_STYLE ('',( #95657 ) ) ; +#32908 = SURFACE_SIDE_STYLE ('',( #2773 ) ) ; +#32909 = VERTEX_POINT ( 'NONE', #23644 ) ; +#32910 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#32911 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32912 = SURFACE_SIDE_STYLE ('',( #15532 ) ) ; +#32913 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32914 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#32915 = STYLED_ITEM ( 'NONE', ( #68151 ), #18618 ) ; +#32916 = VECTOR ( 'NONE', #76513, 1000.000000000000000 ) ; +#32917 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32918 = LINE ( 'NONE', #8832, #31805 ) ; +#32919 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#32920 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32921 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#32922 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32923 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#32925 = VECTOR ( 'NONE', #20979, 1000.000000000000000 ) ; +#32924 = FILL_AREA_STYLE ('',( #11357 ) ) ; +#32926 = VECTOR ( 'NONE', #17206, 1000.000000000000000 ) ; +#32927 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -11.36999999999999922 ) ) ; +#32928 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#32929 = ORIENTED_EDGE ( 'NONE', *, *, #23123, .F. ) ; +#32930 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32932 = ORIENTED_EDGE ( 'NONE', *, *, #10166, .T. ) ; +#32931 = VECTOR ( 'NONE', #18109, 999.9999999999998863 ) ; +#32933 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63842, 'distance_accuracy_value', 'NONE'); +#32934 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24525, 'distance_accuracy_value', 'NONE'); +#32935 = VECTOR ( 'NONE', #82265, 1000.000000000000000 ) ; +#32936 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#32937 = SURFACE_SIDE_STYLE ('',( #78386 ) ) ; +#32938 = SURFACE_STYLE_FILL_AREA ( #94172 ) ; +#32939 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#32940 = PRESENTATION_STYLE_ASSIGNMENT (( #25304 ) ) ; +#32941 = ORIENTED_EDGE ( 'NONE', *, *, #79970, .T. ) ; +#32942 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#32943 = SURFACE_STYLE_USAGE ( .BOTH. , #72240 ) ; +#32944 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9310, 'distance_accuracy_value', 'NONE'); +#32945 = DIRECTION ( 'NONE', ( 0.04281030191567687659, -0.9990832187810425591, 0.000000000000000000 ) ) ; +#32946 = SURFACE_SIDE_STYLE ('',( #63606 ) ) ; +#32947 = ORIENTED_EDGE ( 'NONE', *, *, #6110, .T. ) ; +#32948 = SURFACE_STYLE_USAGE ( .BOTH. , #33976 ) ; +#32949 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32950 = EDGE_CURVE ( 'NONE', #79914, #9663, #84408, .T. ) ; +#32951 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32952 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16578 ), #33014 ) ; +#32953 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.276179938779915091, 0.000000000000000000 ) ) ; +#32954 = FILL_AREA_STYLE_COLOUR ( '', #43035 ) ; +#32956 = ORIENTED_EDGE ( 'NONE', *, *, #2488, .F. ) ; +#32955 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48121 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59403, #35898, #45001 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32957 = SURFACE_STYLE_USAGE ( .BOTH. , #1814 ) ; +#32958 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32959 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6256, 'distance_accuracy_value', 'NONE'); +#32960 = DIRECTION ( 'NONE', ( 0.7071075504167438908, 0.7071060119555143686, 0.000000000000000000 ) ) ; +#32961 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#32962 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32963 = VERTEX_POINT ( 'NONE', #139 ) ; +#32964 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, 0.000000000000000000 ) ) ; +#32965 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, 0.2500000000000000000 ) ) ; +#32966 = ORIENTED_EDGE ( 'NONE', *, *, #43816, .T. ) ; +#32967 = PLANE ( 'NONE', #47849 ) ; +#32968 = FACE_OUTER_BOUND ( 'NONE', #88992, .T. ) ; +#32969 = CARTESIAN_POINT ( 'NONE', ( -0.7059659090909090606, 0.7099999999999999645, 0.5000000000000001110 ) ) ; +#32970 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57399 ) ) ; +#32971 = EDGE_CURVE ( 'NONE', #42447, #59157, #62466, .T. ) ; +#32972 = ORIENTED_EDGE ( 'NONE', *, *, #77794, .F. ) ; +#32973 = ORIENTED_EDGE ( 'NONE', *, *, #3888, .F. ) ; +#32974 = PLANE ( 'NONE', #76794 ) ; +#32976 = FILL_AREA_STYLE_COLOUR ( '', #98553 ) ; +#32975 = FILL_AREA_STYLE ('',( #54460 ) ) ; +#32977 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#32978 = ADVANCED_FACE ( 'NONE', ( #54289, #92059 ), #31795, .F. ) ; +#32979 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4750000000000000333, -0.2399999999999999911 ) ) ; +#32980 = ORIENTED_EDGE ( 'NONE', *, *, #97416, .T. ) ; +#32981 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.399999999999999911, -13.40000000000000036 ) ) ; +#32982 = LINE ( 'NONE', #78428, #60458 ) ; +#32983 = FILL_AREA_STYLE_COLOUR ( '', #80622 ) ; +#32984 = STYLED_ITEM ( 'NONE', ( #12973 ), #18520 ) ; +#32985 = CARTESIAN_POINT ( 'NONE', ( -1.816666666666666652, 3.099999999999989875, 0.000000000000000000 ) ) ; +#32986 = ORIENTED_EDGE ( 'NONE', *, *, #67745, .T. ) ; +#32987 = FILL_AREA_STYLE ('',( #30964 ) ) ; +#32988 = ORIENTED_EDGE ( 'NONE', *, *, #56364, .F. ) ; +#32989 = EDGE_LOOP ( 'NONE', ( #56020, #72259, #59764, #49699 ) ) ; +#32990 = CARTESIAN_POINT ( 'NONE', ( 1.036374481168725659, -1.169468177602907444, 0.8099999999998832578 ) ) ; +#32991 = VECTOR ( 'NONE', #90520, 1000.000000000000000 ) ; +#32992 = AXIS2_PLACEMENT_3D ( 'NONE', #40097, #1281, #94682 ) ; +#32993 = FACE_OUTER_BOUND ( 'NONE', #24795, .T. ) ; +#32994 = FILL_AREA_STYLE ('',( #80472 ) ) ; +#32995 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75296 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45591, #30296, #53319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32996 = ORIENTED_EDGE ( 'NONE', *, *, #4968, .T. ) ; +#32997 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2032 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56668, #94895, #25018 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#32998 = FACE_OUTER_BOUND ( 'NONE', #100634, .T. ) ; +#32999 = FILL_AREA_STYLE ('',( #8918 ) ) ; +#33000 = VERTEX_POINT ( 'NONE', #55320 ) ; +#33001 = FILL_AREA_STYLE_COLOUR ( '', #82087 ) ; +#33002 = VERTEX_POINT ( 'NONE', #47109 ) ; +#33003 = ORIENTED_EDGE ( 'NONE', *, *, #6297, .F. ) ; +#33004 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33005 = FILL_AREA_STYLE ('',( #64157 ) ) ; +#33006 = VECTOR ( 'NONE', #13082, 1000.000000000000000 ) ; +#33007 = LINE ( 'NONE', #94752, #7391 ) ; +#33008 = EDGE_CURVE ( 'NONE', #7996, #17592, #4900, .T. ) ; +#33009 = LINE ( 'NONE', #35044, #28594 ) ; +#33010 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33011 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50290 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97795, #34593, #42729 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33012 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8648700000000000276 ) ) ; +#33013 = PLANE ( 'NONE', #51922 ) ; +#33014 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35564 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35477, #27816, #82427 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33015 = ORIENTED_EDGE ( 'NONE', *, *, #87651, .T. ) ; +#33016 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#33017 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23259 ) ) ; +#33018 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33019 = LINE ( 'NONE', #64171, #63200 ) ; +#33020 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33021 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33022 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33023 = STYLED_ITEM ( 'NONE', ( #67451 ), #52756 ) ; +#33024 = CARTESIAN_POINT ( 'NONE', ( 1.983752383967129829, 1.444956665785265937, -11.39249216584689961 ) ) ; +#33025 = EDGE_CURVE ( 'NONE', #60639, #61874, #39448, .T. ) ; +#33026 = ORIENTED_EDGE ( 'NONE', *, *, #11669, .F. ) ; +#33027 = SURFACE_STYLE_FILL_AREA ( #867 ) ; +#33028 = LINE ( 'NONE', #64181, #54282 ) ; +#33029 = SURFACE_STYLE_FILL_AREA ( #33555 ) ; +#33030 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33031 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33032 = STYLED_ITEM ( 'NONE', ( #12100 ), #87631 ) ; +#33033 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68847 ) ) ; +#33034 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64001, 'distance_accuracy_value', 'NONE'); +#33035 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#33036 = SURFACE_SIDE_STYLE ('',( #89677 ) ) ; +#33037 = VECTOR ( 'NONE', #15740, 1000.000000000000000 ) ; +#33038 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33039 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33040 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15162, #53025, #31545, #61203 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#33041 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33042 = LINE ( 'NONE', #48883, #6328 ) ; +#33043 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33044 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#33046 = EDGE_CURVE ( 'NONE', #17079, #2107, #70595, .T. ) ; +#33045 = CARTESIAN_POINT ( 'NONE', ( 1.894788238603390296, -1.280379325981960026, 0.8100000000000004974 ) ) ; +#33047 = SURFACE_SIDE_STYLE ('',( #63210 ) ) ; +#33048 = AXIS2_PLACEMENT_3D ( 'NONE', #47845, #78985, #77977 ) ; +#33049 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35748, 'distance_accuracy_value', 'NONE'); +#33050 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#33051 = ORIENTED_EDGE ( 'NONE', *, *, #83266, .T. ) ; +#33052 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33053 = FACE_OUTER_BOUND ( 'NONE', #63590, .T. ) ; +#33054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33055 = STYLED_ITEM ( 'NONE', ( #43248 ), #37558 ) ; +#33056 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9509 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57408, #66055, #58437 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33057 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100062, 'distance_accuracy_value', 'NONE'); +#33058 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33060 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33059 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#33061 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33062 = VECTOR ( 'NONE', #26614, 1000.000000000000114 ) ; +#33063 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33064 = VECTOR ( 'NONE', #60832, 1000.000000000000000 ) ; +#33065 = EDGE_CURVE ( 'NONE', #62500, #16114, #93028, .T. ) ; +#33066 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33068 = ORIENTED_EDGE ( 'NONE', *, *, #60402, .T. ) ; +#33069 = LINE ( 'NONE', #34101, #61924 ) ; +#33070 = FACE_OUTER_BOUND ( 'NONE', #71904, .T. ) ; +#33071 = STYLED_ITEM ( 'NONE', ( #90485 ), #59362 ) ; +#33072 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#33073 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33074 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45447, 'distance_accuracy_value', 'NONE'); +#33075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33076 = VECTOR ( 'NONE', #91369, 1000.000000000000000 ) ; +#33077 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42054, 'distance_accuracy_value', 'NONE'); +#33078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33079 = VERTEX_POINT ( 'NONE', #641 ) ; +#33080 = VERTEX_POINT ( 'NONE', #76746 ) ; +#33081 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33082 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8099999999999776268 ) ) ; +#33083 = EDGE_LOOP ( 'NONE', ( #63275, #62145, #46919, #31832 ) ) ; +#33084 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.01000000000000000021, 1.250000000000000000 ) ) ; +#33085 = ADVANCED_FACE ( 'NONE', ( #99619 ), #46065, .T. ) ; +#33086 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33087 = PRESENTATION_STYLE_ASSIGNMENT (( #18224 ) ) ; +#33088 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #5775 ) ; +#33089 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#33090 = PLANE ( 'NONE', #99680 ) ; +#33092 = ORIENTED_EDGE ( 'NONE', *, *, #82521, .T. ) ; +#33091 = VERTEX_POINT ( 'NONE', #1683 ) ; +#33093 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79020 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52470, #36660, #12577 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33094 = EDGE_LOOP ( 'NONE', ( #68489, #67883, #2655, #36526 ) ) ; +#33095 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.499999999999989786, 0.1829999999999999960 ) ) ; +#33096 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#33098 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#33097 = FILL_AREA_STYLE_COLOUR ( '', #42457 ) ; +#33099 = ORIENTED_EDGE ( 'NONE', *, *, #23627, .T. ) ; +#33100 = AXIS2_PLACEMENT_3D ( 'NONE', #79679, #40874, #95446 ) ; +#33101 = EDGE_CURVE ( 'NONE', #89541, #98852, #79277, .T. ) ; +#33102 = SURFACE_SIDE_STYLE ('',( #1463 ) ) ; +#33103 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60815 ) ) ; +#33104 = EDGE_LOOP ( 'NONE', ( #15231, #42650, #17087, #21553, #13923, #45962, #8392, #34086 ) ) ; +#33105 = FILL_AREA_STYLE_COLOUR ( '', #10617 ) ; +#33106 = ORIENTED_EDGE ( 'NONE', *, *, #45550, .T. ) ; +#33108 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33107 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#33109 = AXIS2_PLACEMENT_3D ( 'NONE', #54476, #54980, #85586 ) ; +#33110 = VERTEX_POINT ( 'NONE', #71623 ) ; +#33111 = STYLED_ITEM ( 'NONE', ( #91331 ), #25831 ) ; +#33112 = ORIENTED_EDGE ( 'NONE', *, *, #98481, .T. ) ; +#33113 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8648700000000000276 ) ) ; +#33114 = CIRCLE ( 'NONE', #44521, 1.293010265664959801 ) ; +#33115 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33116 = EDGE_LOOP ( 'NONE', ( #17776, #51425, #3845, #53709 ) ) ; +#33117 = FILL_AREA_STYLE_COLOUR ( '', #95452 ) ; +#33118 = FACE_OUTER_BOUND ( 'NONE', #51976, .T. ) ; +#33119 = LINE ( 'NONE', #27485, #69444 ) ; +#33120 = AXIS2_PLACEMENT_3D ( 'NONE', #233, #55411, #86527 ) ; +#33121 = VECTOR ( 'NONE', #37815, 1000.000000000000000 ) ; +#33122 = ORIENTED_EDGE ( 'NONE', *, *, #69324, .F. ) ; +#33123 = FILL_AREA_STYLE_COLOUR ( '', #95695 ) ; +#33124 = CARTESIAN_POINT ( 'NONE', ( 0.09337595685179390925, -1.316888414733939916, 0.8299999999999999600 ) ) ; +#33125 = ORIENTED_EDGE ( 'NONE', *, *, #100308, .T. ) ; +#33126 = ORIENTED_EDGE ( 'NONE', *, *, #7317, .T. ) ; +#33127 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28489 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59977, #92070, #51295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33128 = PLANE ( 'NONE', #89663 ) ; +#33129 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.7499999999941607820, 0.6999285677797779659 ) ) ; +#33130 = STYLED_ITEM ( 'NONE', ( #88586 ), #37763 ) ; +#33131 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96897 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73595, #57292, #41457 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33132 = FACE_OUTER_BOUND ( 'NONE', #64674, .T. ) ; +#33133 = VECTOR ( 'NONE', #30088, 1000.000000000000000 ) ; +#33134 = EDGE_CURVE ( 'NONE', #52068, #74817, #2683, .T. ) ; +#33135 = EDGE_CURVE ( 'NONE', #43172, #95182, #17960, .T. ) ; +#33136 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000003553, -3.266666666666653285, 0.000000000000000000 ) ) ; +#33137 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#33138 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59828 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8596, #53162, #84295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33139 = ORIENTED_EDGE ( 'NONE', *, *, #21748, .T. ) ; +#33140 = CARTESIAN_POINT ( 'NONE', ( 0.3664728319017789837, -1.220832247304010298, 0.8299999999999999600 ) ) ; +#33141 = ORIENTED_EDGE ( 'NONE', *, *, #78919, .F. ) ; +#33142 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36428 ) ) ; +#33143 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.000000000000000000 ) ) ; +#33144 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33145 = LINE ( 'NONE', #16265, #90801 ) ; +#33146 = STYLED_ITEM ( 'NONE', ( #12050 ), #11496 ) ; +#33147 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33149 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33148 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.6999999999999999556, 0.1829999999999790128 ) ) ; +#33150 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33151 = FILL_AREA_STYLE ('',( #48494 ) ) ; +#33152 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#33153 = ADVANCED_FACE ( 'NONE', ( #56332 ), #57325, .T. ) ; +#33154 = ADVANCED_FACE ( 'NONE', ( #49659 ), #10739, .T. ) ; +#33155 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.383333333333323090, 0.000000000000000000 ) ) ; +#33156 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#33157 = CARTESIAN_POINT ( 'NONE', ( -1.204376861304429891, -0.9585643914498560569, 0.8299999999999998490 ) ) ; +#33158 = AXIS2_PLACEMENT_3D ( 'NONE', #16079, #7355, #38584 ) ; +#33159 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#33160 = EDGE_CURVE ( 'NONE', #61880, #50760, #60346, .T. ) ; +#33161 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33162 = PLANE ( 'NONE', #70110 ) ; +#33163 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#33164 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33165 = SURFACE_STYLE_FILL_AREA ( #1010 ) ; +#33166 = AXIS2_PLACEMENT_3D ( 'NONE', #94247, #18140, #1863 ) ; +#33167 = SURFACE_STYLE_FILL_AREA ( #96929 ) ; +#33168 = EDGE_CURVE ( 'NONE', #90815, #25877, #87756, .T. ) ; +#33169 = CONICAL_SURFACE ( 'NONE', #77171, 0.6999999999948158802, 0.7853981633974482790 ) ; +#33170 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43836, 'distance_accuracy_value', 'NONE'); +#33171 = SHAPE_REPRESENTATION ( 'C0201_20210301.xtd', ( #82894 ), #63115 ) ; +#33172 = ORIENTED_EDGE ( 'NONE', *, *, #15731, .F. ) ; +#33173 = LINE ( 'NONE', #26530, #1944 ) ; +#33174 = CARTESIAN_POINT ( 'NONE', ( 1.585937742812469908, -0.9305358755170231033, 0.8100000000000000533 ) ) ; +#33175 = VERTEX_POINT ( 'NONE', #81809 ) ; +#33176 = FILL_AREA_STYLE_COLOUR ( '', #19185 ) ; +#33177 = SURFACE_STYLE_FILL_AREA ( #42360 ) ; +#33178 = EDGE_CURVE ( 'NONE', #41179, #7585, #27764, .T. ) ; +#33179 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.4245906043549200204, 0.1900000000000000300 ) ) ; +#33180 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#33181 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33182 = FILL_AREA_STYLE_COLOUR ( '', #29636 ) ; +#33183 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59316 ), #95095 ) ; +#33184 = EDGE_CURVE ( 'NONE', #43001, #26730, #82309, .T. ) ; +#33185 = SURFACE_SIDE_STYLE ('',( #4041 ) ) ; +#33186 = EDGE_LOOP ( 'NONE', ( #100430, #30642, #42066, #45461 ) ) ; +#33187 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33188 = EDGE_CURVE ( 'NONE', #68558, #91699, #50179, .T. ) ; +#33189 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33190 = ORIENTED_EDGE ( 'NONE', *, *, #13893, .T. ) ; +#33191 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909090190, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#33192 = LINE ( 'NONE', #33709, #12018 ) ; +#33193 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 7.678360999999999770, 0.8991599999999999593 ) ) ; +#33194 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, 0.2250000000000000333 ) ) ; +#33195 = EDGE_CURVE ( 'NONE', #94260, #62517, #82793, .T. ) ; +#33196 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.000000000000000000 ) ) ; +#33197 = FACE_OUTER_BOUND ( 'NONE', #80563, .T. ) ; +#33198 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91909 ) ) ; +#33199 = LINE ( 'NONE', #65329, #6074 ) ; +#33200 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33201 = EDGE_LOOP ( 'NONE', ( #80331, #34425, #41192, #78671 ) ) ; +#33202 = AXIS2_PLACEMENT_3D ( 'NONE', #84913, #55331, #54817 ) ; +#33203 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #57956, #89561, #74743, #89061 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#33204 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #60494 ) ) ; +#33205 = PLANE ( 'NONE', #28943 ) ; +#33206 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33207 = ORIENTED_EDGE ( 'NONE', *, *, #70097, .T. ) ; +#33208 = FILL_AREA_STYLE_COLOUR ( '', #58890 ) ; +#33209 = AXIS2_PLACEMENT_3D ( 'NONE', #955, #80594, #10517 ) ; +#33210 = VECTOR ( 'NONE', #84500, 1000.000000000000000 ) ; +#33211 = FACE_OUTER_BOUND ( 'NONE', #98124, .T. ) ; +#33212 = EDGE_LOOP ( 'NONE', ( #29103, #85950, #72071, #34236 ) ) ; +#33213 = CYLINDRICAL_SURFACE ( 'NONE', #23436, 0.04999999999999999584 ) ; +#33214 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.1000000000000006856, 0.1829999999999710192 ) ) ; +#33215 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33216 = EDGE_CURVE ( 'NONE', #43001, #6286, #52172, .T. ) ; +#33217 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33219 = ORIENTED_EDGE ( 'NONE', *, *, #9528, .T. ) ; +#33218 = ORIENTED_EDGE ( 'NONE', *, *, #67312, .F. ) ; +#33220 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36510 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56397, #26235, #18541 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33221 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#33222 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33223 = VECTOR ( 'NONE', #36435, 1000.000000000000000 ) ; +#33224 = LINE ( 'NONE', #49560, #64288 ) ; +#33225 = VERTEX_POINT ( 'NONE', #58851 ) ; +#33226 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#33227 = VECTOR ( 'NONE', #93587, 1000.000000000000000 ) ; +#33228 = FACE_OUTER_BOUND ( 'NONE', #90103, .T. ) ; +#33229 = ORIENTED_EDGE ( 'NONE', *, *, #76551, .T. ) ; +#33230 = EDGE_CURVE ( 'NONE', #9027, #5457, #35852, .T. ) ; +#33231 = ORIENTED_EDGE ( 'NONE', *, *, #88059, .T. ) ; +#33232 = DIRECTION ( 'NONE', ( 0.7071067806865475314, -0.7071067816865476141, -0.000000000000000000 ) ) ; +#33233 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33234 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33235 = CARTESIAN_POINT ( 'NONE', ( -0.1830714119375710103, -0.9850088450568520448, 0.8300000000000000711 ) ) ; +#33236 = VECTOR ( 'NONE', #78772, 1000.000000000000000 ) ; +#33238 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#33237 = FACE_OUTER_BOUND ( 'NONE', #95495, .T. ) ; +#33239 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#33240 = ORIENTED_EDGE ( 'NONE', *, *, #97511, .F. ) ; +#33241 = ADVANCED_FACE ( 'NONE', ( #74133 ), #43979, .T. ) ; +#33242 = VERTEX_POINT ( 'NONE', #19496 ) ; +#33243 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33244 = EDGE_LOOP ( 'NONE', ( #13672, #100767, #83253, #89654 ) ) ; +#33245 = LINE ( 'NONE', #25106, #52502 ) ; +#33246 = EDGE_CURVE ( 'NONE', #97292, #14950, #62096, .T. ) ; +#33247 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23909 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2126, #59300, #67882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33248 = VERTEX_POINT ( 'NONE', #27691 ) ; +#33249 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#33250 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13620 ) ) ; +#33251 = EDGE_LOOP ( 'NONE', ( #66496, #11099, #1082, #84452 ) ) ; +#33252 = FILL_AREA_STYLE ('',( #72054 ) ) ; +#33253 = CARTESIAN_POINT ( 'NONE', ( -1.005891190074376551, -1.394896464896026256, 0.8099999999996969624 ) ) ; +#33254 = EDGE_LOOP ( 'NONE', ( #30659, #42462, #20568, #44446, #9891 ) ) ; +#33255 = VECTOR ( 'NONE', #90528, 1000.000000000000000 ) ; +#33256 = FACE_OUTER_BOUND ( 'NONE', #76652, .T. ) ; +#33257 = VECTOR ( 'NONE', #7709, 1000.000000000000000 ) ; +#33258 = STYLED_ITEM ( 'NONE', ( #38358 ), #26320 ) ; +#33260 = EDGE_CURVE ( 'NONE', #11881, #56601, #59854, .T. ) ; +#33259 = LINE ( 'NONE', #64399, #83574 ) ; +#33261 = EDGE_CURVE ( 'NONE', #84912, #91646, #69451, .T. ) ; +#33262 = FACE_OUTER_BOUND ( 'NONE', #84303, .T. ) ; +#33263 = LINE ( 'NONE', #17405, #1485 ) ; +#33264 = LINE ( 'NONE', #40430, #75973 ) ; +#33265 = CARTESIAN_POINT ( 'NONE', ( 1.585431502668920078, -1.054251812769849916, 0.8299999999999990719 ) ) ; +#33266 = EDGE_LOOP ( 'NONE', ( #22713, #39128, #44360, #86866 ) ) ; +#33267 = LINE ( 'NONE', #18926, #37608 ) ; +#33268 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33270 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#33269 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#33271 = ORIENTED_EDGE ( 'NONE', *, *, #45728, .T. ) ; +#33272 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33273 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33274 = CARTESIAN_POINT ( 'NONE', ( -0.3116609922593340243, -1.321596304865350069, 0.8100000000000000533 ) ) ; +#33275 = FILL_AREA_STYLE ('',( #95008 ) ) ; +#33276 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95176 ), #13731 ) ; +#33277 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#33279 = PRESENTATION_STYLE_ASSIGNMENT (( #62410 ) ) ; +#33278 = LINE ( 'NONE', #17417, #47904 ) ; +#33281 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13651 ) ) ; +#33280 = CARTESIAN_POINT ( 'NONE', ( 1.071224486614660298, 1.221896575926969986, 0.8100000000000000533 ) ) ; +#33282 = LINE ( 'NONE', #40952, #87385 ) ; +#33283 = EDGE_CURVE ( 'NONE', #88828, #66888, #54159, .T. ) ; +#33285 = AXIS2_PLACEMENT_3D ( 'NONE', #40699, #9457, #30461 ) ; +#33284 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75677 ) ) ; +#33286 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33287 = ADVANCED_FACE ( 'NONE', ( #33070 ), #45443, .F. ) ; +#33288 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54503 ) ) ; +#33289 = SURFACE_STYLE_USAGE ( .BOTH. , #80260 ) ; +#33290 = SURFACE_STYLE_USAGE ( .BOTH. , #41959 ) ; +#33291 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33292 = ORIENTED_EDGE ( 'NONE', *, *, #89965, .F. ) ; +#33293 = SURFACE_SIDE_STYLE ('',( #18442 ) ) ; +#33294 = CIRCLE ( 'NONE', #25158, 0.6999999999999999556 ) ; +#33295 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#33296 = AXIS2_PLACEMENT_3D ( 'NONE', #10291, #42047, #55867 ) ; +#33297 = PRESENTATION_STYLE_ASSIGNMENT (( #32781 ) ) ; +#33298 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33299 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39429, 'distance_accuracy_value', 'NONE'); +#33300 = ORIENTED_EDGE ( 'NONE', *, *, #5866, .T. ) ; +#33301 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33302 = CARTESIAN_POINT ( 'NONE', ( -1.115369118623960043, -0.9585098101514269997, 0.8299999999999999600 ) ) ; +#33303 = FILL_AREA_STYLE ('',( #25164 ) ) ; +#33304 = EDGE_CURVE ( 'NONE', #36803, #38519, #7594, .T. ) ; +#33305 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#33306 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#33307 = FILL_AREA_STYLE ('',( #63944 ) ) ; +#33308 = CARTESIAN_POINT ( 'NONE', ( -1.038348751223719946, -1.423389424083600030, 0.8300000000000001821 ) ) ; +#33309 = FILL_AREA_STYLE ('',( #56315 ) ) ; +#33310 = ADVANCED_FACE ( 'NONE', ( #92427 ), #69957, .F. ) ; +#33311 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#33312 = ORIENTED_EDGE ( 'NONE', *, *, #18249, .F. ) ; +#33313 = PRESENTATION_STYLE_ASSIGNMENT (( #63472 ) ) ; +#33314 = EDGE_CURVE ( 'NONE', #22324, #36117, #73112, .T. ) ; +#33315 = STYLED_ITEM ( 'NONE', ( #49475 ), #71366 ) ; +#33316 = ORIENTED_EDGE ( 'NONE', *, *, #54093, .F. ) ; +#33317 = LINE ( 'NONE', #64454, #27454 ) ; +#33318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96930, 'distance_accuracy_value', 'NONE'); +#33319 = CARTESIAN_POINT ( 'NONE', ( 0.9399999999999999467, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#33320 = SURFACE_SIDE_STYLE ('',( #16951 ) ) ; +#33321 = FACE_OUTER_BOUND ( 'NONE', #67881, .T. ) ; +#33322 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#33323 = FACE_OUTER_BOUND ( 'NONE', #55091, .T. ) ; +#33324 = FILL_AREA_STYLE ('',( #19987 ) ) ; +#33325 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#33326 = VECTOR ( 'NONE', #33273, 1000.000000000000000 ) ; +#33327 = FILL_AREA_STYLE_COLOUR ( '', #70059 ) ; +#33328 = EDGE_LOOP ( 'NONE', ( #79982, #46102, #84798, #79479 ) ) ; +#33329 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#33330 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33331 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33332 = VERTEX_POINT ( 'NONE', #21496 ) ; +#33333 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49286 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66918, #74093, #57283 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33334 = AXIS2_PLACEMENT_3D ( 'NONE', #32275, #63923, #93992 ) ; +#33335 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33336 = VERTEX_POINT ( 'NONE', #87691 ) ; +#33337 = STYLED_ITEM ( 'NONE', ( #29647 ), #48016 ) ; +#33338 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33339 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 9.400141255666570662E-17, 0.6199999999999999956 ) ) ; +#33340 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33341 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33342 = STYLED_ITEM ( 'NONE', ( #82081 ), #76955 ) ; +#33343 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33344 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, -3.500000000000000444, 0.000000000000000000 ) ) ; +#33345 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2896 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12651, #76499, #76002 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33346 = ORIENTED_EDGE ( 'NONE', *, *, #58411, .F. ) ; +#33347 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#33348 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#33349 = ORIENTED_EDGE ( 'NONE', *, *, #55304, .F. ) ; +#33350 = AXIS2_PLACEMENT_3D ( 'NONE', #65285, #96403, #26008 ) ; +#33351 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85499 ) ) ; +#33352 = AXIS2_PLACEMENT_3D ( 'NONE', #19974, #74117, #4164 ) ; +#33353 = PLANE ( 'NONE', #29536 ) ; +#33354 = ADVANCED_FACE ( 'NONE', ( #10997 ), #33590, .F. ) ; +#33355 = ORIENTED_EDGE ( 'NONE', *, *, #63895, .T. ) ; +#33357 = STYLED_ITEM ( 'NONE', ( #24133 ), #29071 ) ; +#33356 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33358 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33359 = PLANE ( 'NONE', #40828 ) ; +#33360 = VECTOR ( 'NONE', #82524, 1000.000000000000000 ) ; +#33361 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33362 = LINE ( 'NONE', #38991, #32042 ) ; +#33363 = ORIENTED_EDGE ( 'NONE', *, *, #8707, .F. ) ; +#33364 = EDGE_CURVE ( 'NONE', #75309, #85305, #96325, .T. ) ; +#33366 = VERTEX_POINT ( 'NONE', #34600 ) ; +#33365 = ORIENTED_EDGE ( 'NONE', *, *, #81278, .F. ) ; +#33367 = LINE ( 'NONE', #16996, #90666 ) ; +#33368 = STYLED_ITEM ( 'NONE', ( #76578 ), #61364 ) ; +#33369 = ORIENTED_EDGE ( 'NONE', *, *, #45515, .T. ) ; +#33370 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#33371 = ADVANCED_FACE ( 'NONE', ( #18726 ), #57591, .T. ) ; +#33372 = VERTEX_POINT ( 'NONE', #97327 ) ; +#33374 = EDGE_LOOP ( 'NONE', ( #76360, #23677, #2812, #17790 ) ) ; +#33373 = PRESENTATION_STYLE_ASSIGNMENT (( #56870 ) ) ; +#33375 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14449, #29317, #68599, #36498, #13941, #13412, #67590, #37988, #60978, #98671, #21154, #44608, #76776, #36991, #68092, #60491, #91593, #32844, #87466 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.234508619761113211E-05, 4.370190546328685531E-05, 6.423309290663750865E-05, 8.416080901307864976E-05, 0.0001034426640163906903, 0.0001220538614379072318, 0.0001403618142760070886, 0.0001584534022805502026, 0.0001764955483670874799, 0.0001946270033858287863, 0.0002131061436272919604, 0.0002322220534159277143, 0.0002519406089841068797, 0.0002725210458542984553, 0.0002938778651199739278, 0.0003164559277781382697 ), + .UNSPECIFIED. ) ; +#33376 = LINE ( 'NONE', #3224, #54068 ) ; +#33377 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33378 = PRESENTATION_STYLE_ASSIGNMENT (( #87480 ) ) ; +#33379 = STYLED_ITEM ( 'NONE', ( #4085 ), #68647 ) ; +#33380 = ORIENTED_EDGE ( 'NONE', *, *, #35052, .T. ) ; +#33382 = EDGE_CURVE ( 'NONE', #99988, #27582, #25936, .T. ) ; +#33381 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#33383 = ORIENTED_EDGE ( 'NONE', *, *, #83946, .F. ) ; +#33384 = SURFACE_SIDE_STYLE ('',( #63530 ) ) ; +#33385 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8648700000000000276 ) ) ; +#33386 = VECTOR ( 'NONE', #63622, 1000.000000000000000 ) ; +#33387 = ORIENTED_EDGE ( 'NONE', *, *, #82354, .F. ) ; +#33388 = VECTOR ( 'NONE', #51836, 1000.000000000000000 ) ; +#33390 = EDGE_CURVE ( 'NONE', #56601, #52699, #89205, .T. ) ; +#33389 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999999762, 0.8648700000000000276 ) ) ; +#33391 = EDGE_CURVE ( 'NONE', #43549, #88638, #82065, .T. ) ; +#33392 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33393 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33394 = STYLED_ITEM ( 'NONE', ( #5342 ), #71595 ) ; +#33395 = ADVANCED_FACE ( 'NONE', ( #73888 ), #35106, .T. ) ; +#33396 = EDGE_CURVE ( 'NONE', #38490, #20037, #83554, .T. ) ; +#33397 = CIRCLE ( 'NONE', #26844, 0.1000000000000000472 ) ; +#33398 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33400 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33399 = SURFACE_STYLE_FILL_AREA ( #23718 ) ; +#33401 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#33402 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33403 = ADVANCED_FACE ( 'NONE', ( #82557 ), #67696, .T. ) ; +#33404 = CARTESIAN_POINT ( 'NONE', ( -1.089947272470209949, -0.8906029366306299488, 0.8100000000000000533 ) ) ; +#33405 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33406 = EDGE_LOOP ( 'NONE', ( #49317, #76057, #96491, #8642, #28984, #26178, #11499, #10247, #79042, #61148, #74226, #3825 ) ) ; +#33408 = AXIS2_PLACEMENT_3D ( 'NONE', #22901, #91805, #83678 ) ; +#33407 = FILL_AREA_STYLE_COLOUR ( '', #8683 ) ; +#33409 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77392 ) ) ; +#33410 = ADVANCED_FACE ( 'NONE', ( #29908 ), #91686, .F. ) ; +#33411 = FACE_OUTER_BOUND ( 'NONE', #54105, .T. ) ; +#33412 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33413 = PLANE ( 'NONE', #78662 ) ; +#33414 = PLANE ( 'NONE', #23839 ) ; +#33415 = VERTEX_POINT ( 'NONE', #55454 ) ; +#33416 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#33417 = SURFACE_STYLE_FILL_AREA ( #25267 ) ; +#33418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12176 ), #61191 ) ; +#33421 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#33420 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#33419 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33422 = CARTESIAN_POINT ( 'NONE', ( 1.585431502668920078, -1.054251812769849916, 0.8299999999999999600 ) ) ; +#33423 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55249, 'distance_accuracy_value', 'NONE'); +#33424 = PLANE ( 'NONE', #32272 ) ; +#33425 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8817 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36181, #20832, #83634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #983 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89563, #90561, #99132 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33427 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#33428 = SURFACE_STYLE_USAGE ( .BOTH. , #88535 ) ; +#33429 = ORIENTED_EDGE ( 'NONE', *, *, #8233, .F. ) ; +#33430 = FILL_AREA_STYLE_COLOUR ( '', #14676 ) ; +#33431 = CARTESIAN_POINT ( 'NONE', ( 0.2314326298701300244, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#33434 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9828 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7030, #76059, #59796 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33433 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7230 ) ) ; +#33432 = FILL_AREA_STYLE_COLOUR ( '', #15488 ) ; +#33435 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#33436 = LINE ( 'NONE', #2288, #48559 ) ; +#33437 = LINE ( 'NONE', #4278, #33853 ) ; +#33438 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33439 = FILL_AREA_STYLE_COLOUR ( '', #4996 ) ; +#33440 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33441 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33442 = SURFACE_STYLE_FILL_AREA ( #95671 ) ; +#33443 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33444 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#33445 = ORIENTED_EDGE ( 'NONE', *, *, #81329, .F. ) ; +#33446 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#33447 = EDGE_CURVE ( 'NONE', #88325, #828, #23790, .T. ) ; +#33448 = ORIENTED_EDGE ( 'NONE', *, *, #66063, .T. ) ; +#33449 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36714 ), #93715 ) ; +#33450 = CARTESIAN_POINT ( 'NONE', ( 0.2602800372128030171, -1.290215378870249952, 0.8100000000000010525 ) ) ; +#33451 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#33452 = PLANE ( 'NONE', #86270 ) ; +#33453 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#33454 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33456 = EDGE_CURVE ( 'NONE', #83836, #35029, #78399, .T. ) ; +#33455 = PRESENTATION_STYLE_ASSIGNMENT (( #95178 ) ) ; +#33457 = SURFACE_SIDE_STYLE ('',( #17582 ) ) ; +#33458 = ORIENTED_EDGE ( 'NONE', *, *, #7680, .F. ) ; +#33459 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33460 = SURFACE_SIDE_STYLE ('',( #10357 ) ) ; +#33461 = FILL_AREA_STYLE ('',( #41124 ) ) ; +#33462 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95345 ) ) ; +#33463 = LINE ( 'NONE', #41125, #45438 ) ; +#33464 = VERTEX_POINT ( 'NONE', #48296 ) ; +#33465 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7177 ) ) ; +#33466 = LINE ( 'NONE', #77886, #58222 ) ; +#33467 = FACE_OUTER_BOUND ( 'NONE', #44485, .T. ) ; +#33468 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33469 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33471 = EDGE_CURVE ( 'NONE', #73740, #60497, #68193, .T. ) ; +#33470 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#33472 = EDGE_LOOP ( 'NONE', ( #88898, #90606, #48576, #35396, #44578, #65369 ) ) ; +#33473 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33474 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61119, 'distance_accuracy_value', 'NONE'); +#33475 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33476 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27457 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10061, #33144, #95390 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33477 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#33479 = EDGE_CURVE ( 'NONE', #28522, #48677, #46728, .T. ) ; +#33478 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33480 = VERTEX_POINT ( 'NONE', #30919 ) ; +#33481 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#33482 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#33483 = FILL_AREA_STYLE_COLOUR ( '', #78620 ) ; +#33484 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#33485 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33486 = LINE ( 'NONE', #63628, #46663 ) ; +#33487 = SURFACE_STYLE_USAGE ( .BOTH. , #71771 ) ; +#33488 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #88759 ) ; +#33489 = EDGE_CURVE ( 'NONE', #68437, #15440, #32454, .T. ) ; +#33490 = ORIENTED_EDGE ( 'NONE', *, *, #74406, .F. ) ; +#33492 = VERTEX_POINT ( 'NONE', #79422 ) ; +#33491 = SURFACE_STYLE_FILL_AREA ( #73299 ) ; +#33494 = AXIS2_PLACEMENT_3D ( 'NONE', #99989, #70452, #60825 ) ; +#33493 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2608, 'distance_accuracy_value', 'NONE'); +#33495 = FILL_AREA_STYLE ('',( #64620 ) ) ; +#33496 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33497 = SURFACE_STYLE_FILL_AREA ( #72789 ) ; +#33498 = VECTOR ( 'NONE', #27300, 1000.000000000000000 ) ; +#33499 = EDGE_CURVE ( 'NONE', #20296, #42663, #40115, .T. ) ; +#33500 = STYLED_ITEM ( 'NONE', ( #1584 ), #2819 ) ; +#33501 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#33502 = ORIENTED_EDGE ( 'NONE', *, *, #98209, .F. ) ; +#33503 = FILL_AREA_STYLE ('',( #41156 ) ) ; +#33504 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33506 = VECTOR ( 'NONE', #10945, 1000.000000000000000 ) ; +#33505 = VECTOR ( 'NONE', #96992, 999.9999999999998863 ) ; +#33507 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69368 ), #59626 ) ; +#33508 = VERTEX_POINT ( 'NONE', #62105 ) ; +#33509 = VERTEX_POINT ( 'NONE', #85039 ) ; +#33510 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20648 ) ) ; +#33511 = ORIENTED_EDGE ( 'NONE', *, *, #13691, .F. ) ; +#33512 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#33513 = ADVANCED_FACE ( 'NONE', ( #77371 ), #31942, .T. ) ; +#33515 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33514 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33516 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000009645, -0.2400000000000000189 ) ) ; +#33517 = ORIENTED_EDGE ( 'NONE', *, *, #73385, .T. ) ; +#33518 = AXIS2_PLACEMENT_3D ( 'NONE', #69492, #29701, #95355 ) ; +#33519 = EDGE_CURVE ( 'NONE', #64767, #13302, #62607, .T. ) ; +#33520 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33521 = EDGE_CURVE ( 'NONE', #33225, #27956, #48710, .T. ) ; +#33522 = ORIENTED_EDGE ( 'NONE', *, *, #92510, .T. ) ; +#33523 = CARTESIAN_POINT ( 'NONE', ( 1.291611456110860034, -1.433733517242619993, 0.8100000000000000533 ) ) ; +#33524 = ORIENTED_EDGE ( 'NONE', *, *, #4182, .T. ) ; +#33525 = ORIENTED_EDGE ( 'NONE', *, *, #83059, .T. ) ; +#33526 = SURFACE_STYLE_FILL_AREA ( #48352 ) ; +#33527 = SURFACE_STYLE_USAGE ( .BOTH. , #48353 ) ; +#33528 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8100000000000000533 ) ) ; +#33529 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#33530 = SURFACE_STYLE_FILL_AREA ( #71818 ) ; +#33531 = EDGE_CURVE ( 'NONE', #16343, #42493, #47253, .T. ) ; +#33532 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33533 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#33534 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33535 = CARTESIAN_POINT ( 'NONE', ( -0.04997673550079750199, -1.145059460293619935, 0.8100000000000000533 ) ) ; +#33536 = LINE ( 'NONE', #87639, #4652 ) ; +#33537 = EDGE_CURVE ( 'NONE', #83206, #46497, #8863, .T. ) ; +#33538 = VERTEX_POINT ( 'NONE', #10881 ) ; +#33540 = VECTOR ( 'NONE', #70017, 1000.000000000000000 ) ; +#33539 = SURFACE_STYLE_FILL_AREA ( #9451 ) ; +#33541 = SURFACE_STYLE_USAGE ( .BOTH. , #80005 ) ; +#33542 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, -0.000000000000000000 ) ) ; +#33543 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99884, 'distance_accuracy_value', 'NONE'); +#33544 = SURFACE_STYLE_FILL_AREA ( #55016 ) ; +#33545 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33546 = VECTOR ( 'NONE', #35162, 1000.000000000000000 ) ; +#33547 = STYLED_ITEM ( 'NONE', ( #82786 ), #90018 ) ; +#33548 = CARTESIAN_POINT ( 'NONE', ( -0.1525528712910690365, -1.164063370418184196, 0.8233333333333333615 ) ) ; +#33549 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#33550 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#33551 = ORIENTED_EDGE ( 'NONE', *, *, #19066, .F. ) ; +#33552 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18856 ), #5783 ) ; +#33553 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33554 = SURFACE_SIDE_STYLE ('',( #2399 ) ) ; +#33555 = FILL_AREA_STYLE ('',( #17183 ) ) ; +#33556 = VECTOR ( 'NONE', #30421, 1000.000000000000000 ) ; +#33557 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#33558 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000000001155, -0.7000000000585895332 ) ) ; +#33559 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#33560 = CARTESIAN_POINT ( 'NONE', ( 0.3332327486577990050, -1.242627591519610109, 0.8300000000000015143 ) ) ; +#33561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47115 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26478, #79085, #25986 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33563 = VECTOR ( 'NONE', #36975, 1000.000000000000000 ) ; +#33562 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33564 = STYLED_ITEM ( 'NONE', ( #38839 ), #25741 ) ; +#33565 = FACE_OUTER_BOUND ( 'NONE', #20136, .T. ) ; +#33566 = LINE ( 'NONE', #78997, #2232 ) ; +#33567 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33568 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33570 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#33569 = STYLED_ITEM ( 'NONE', ( #87338 ), #77457 ) ; +#33571 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#33572 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33573 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33574 = FILL_AREA_STYLE_COLOUR ( '', #21226 ) ; +#33575 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33576 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33577 = EDGE_CURVE ( 'NONE', #63097, #63924, #31080, .T. ) ; +#33578 = VERTEX_POINT ( 'NONE', #88083 ) ; +#33579 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33580 = PLANE ( 'NONE', #60001 ) ; +#33581 = AXIS2_PLACEMENT_3D ( 'NONE', #37765, #37278, #92364 ) ; +#33582 = AXIS2_PLACEMENT_3D ( 'NONE', #38820, #69938, #9514 ) ; +#33583 = FACE_OUTER_BOUND ( 'NONE', #63994, .T. ) ; +#33584 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33585 = LINE ( 'NONE', #64706, #61826 ) ; +#33586 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3627, #41434, #88386 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33587 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.650000000000000355, 0.000000000000000000 ) ) ; +#33588 = ORIENTED_EDGE ( 'NONE', *, *, #40003, .F. ) ; +#33589 = LINE ( 'NONE', #64214, #86320 ) ; +#33590 = PLANE ( 'NONE', #62092 ) ; +#33591 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79201 ), #2531 ) ; +#33592 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.2500000000000001110 ) ) ; +#33593 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33594 = ADVANCED_FACE ( 'NONE', ( #64097 ), #72759, .T. ) ; +#33595 = ORIENTED_EDGE ( 'NONE', *, *, #62108, .T. ) ; +#33596 = ORIENTED_EDGE ( 'NONE', *, *, #83411, .T. ) ; +#33597 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33598 = SURFACE_STYLE_USAGE ( .BOTH. , #17731 ) ; +#33599 = ORIENTED_EDGE ( 'NONE', *, *, #25541, .F. ) ; +#33600 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#33601 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20522 ) ) ; +#33602 = PLANE ( 'NONE', #44975 ) ; +#33603 = ADVANCED_FACE ( 'NONE', ( #57980 ), #7205, .F. ) ; +#33604 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33605 = SHAPE_DEFINITION_REPRESENTATION ( #68603, #85938 ) ; +#33606 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000013115, -0.2400000000000000189 ) ) ; +#33607 = CARTESIAN_POINT ( 'NONE', ( 0.9822683152950091312, -1.404803802054167328, 0.8099999999997352651 ) ) ; +#33608 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51555 ) ) ; +#33610 = ORIENTED_EDGE ( 'NONE', *, *, #57481, .T. ) ; +#33609 = ORIENTED_EDGE ( 'NONE', *, *, #32828, .T. ) ; +#33611 = ORIENTED_EDGE ( 'NONE', *, *, #681, .T. ) ; +#33612 = ORIENTED_EDGE ( 'NONE', *, *, #73701, .F. ) ; +#33613 = VECTOR ( 'NONE', #38637, 1000.000000000000000 ) ; +#33614 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33615 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43077, 'distance_accuracy_value', 'NONE'); +#33616 = CARTESIAN_POINT ( 'NONE', ( 1.793184587716770029, -1.490633633148249926, 0.8299999999999999600 ) ) ; +#33617 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33618 = ORIENTED_EDGE ( 'NONE', *, *, #83391, .F. ) ; +#33619 = EDGE_CURVE ( 'NONE', #32075, #1722, #91084, .T. ) ; +#33620 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51272 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53805, #84442, #14451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33621 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33622 = FILL_AREA_STYLE ('',( #47915 ) ) ; +#33623 = FILL_AREA_STYLE_COLOUR ( '', #55503 ) ; +#33624 = VECTOR ( 'NONE', #28829, 1000.000000000000000 ) ; +#33625 = EDGE_LOOP ( 'NONE', ( #54182, #59250, #60643, #16822, #57328, #42526 ) ) ; +#33626 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#33627 = ORIENTED_EDGE ( 'NONE', *, *, #90316, .F. ) ; +#33628 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94040 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22825, #46253, #46773 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33629 = VECTOR ( 'NONE', #4553, 1000.000000000000000 ) ; +#33630 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33631 = VERTEX_POINT ( 'NONE', #12894 ) ; +#33632 = ORIENTED_EDGE ( 'NONE', *, *, #5887, .F. ) ; +#33633 = FILL_AREA_STYLE_COLOUR ( '', #70474 ) ; +#33635 = FACE_OUTER_BOUND ( 'NONE', #5669, .T. ) ; +#33634 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33636 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33637 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95531 ) ) ; +#33638 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33640 = ORIENTED_EDGE ( 'NONE', *, *, #54731, .T. ) ; +#33639 = LINE ( 'NONE', #10036, #91785 ) ; +#33641 = EDGE_CURVE ( 'NONE', #89230, #84842, #44116, .T. ) ; +#33642 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.699999999999999956, 0.000000000000000000 ) ) ; +#33643 = CARTESIAN_POINT ( 'NONE', ( -0.2677310921211660810, -0.9808836469697851390, 0.8100000000000000533 ) ) ; +#33644 = ORIENTED_EDGE ( 'NONE', *, *, #64613, .F. ) ; +#33646 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#33645 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33647 = SURFACE_SIDE_STYLE ('',( #24986 ) ) ; +#33648 = VERTEX_POINT ( 'NONE', #21137 ) ; +#33649 = ORIENTED_EDGE ( 'NONE', *, *, #45134, .F. ) ; +#33651 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999734, 0.6599999999999998090, 0.9757359312880711233 ) ) ; +#33650 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33652 = CARTESIAN_POINT ( 'NONE', ( 1.706409873422509937, -1.445184491613219935, 0.8300000000000002931 ) ) ; +#33653 = VECTOR ( 'NONE', #85596, 1000.000000000000114 ) ; +#33654 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33655 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33656 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33657 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33658 = SURFACE_SIDE_STYLE ('',( #8033 ) ) ; +#33659 = ADVANCED_FACE ( 'NONE', ( #43600 ), #51301, .T. ) ; +#33660 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34566, 'distance_accuracy_value', 'NONE'); +#33661 = VECTOR ( 'NONE', #30829, 1000.000000000000000 ) ; +#33662 = ORIENTED_EDGE ( 'NONE', *, *, #15237, .T. ) ; +#33663 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8299999999999999600 ) ) ; +#33664 = SURFACE_STYLE_FILL_AREA ( #56139 ) ; +#33665 = VERTEX_POINT ( 'NONE', #52793 ) ; +#33666 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53587 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38625, #30969, #46768 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33667 = FILL_AREA_STYLE ('',( #89280 ) ) ; +#33668 = SURFACE_STYLE_USAGE ( .BOTH. , #57675 ) ; +#33669 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33670 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72264, #31959, #41140 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33671 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33672 = PLANE ( 'NONE', #99175 ) ; +#33673 = LINE ( 'NONE', #96907, #27267 ) ; +#33674 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#33675 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#33676 = SURFACE_STYLE_USAGE ( .BOTH. , #19330 ) ; +#33677 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#33678 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33679 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#33680 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#33681 = ADVANCED_FACE ( 'NONE', ( #98168 ), #83927, .T. ) ; +#33682 = STYLED_ITEM ( 'NONE', ( #72080 ), #30418 ) ; +#33683 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8648700000000000276 ) ) ; +#33684 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8648700000000000276 ) ) ; +#33685 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33686 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8648700000000000276 ) ) ; +#33687 = AXIS2_PLACEMENT_3D ( 'NONE', #89179, #81554, #20214 ) ; +#33688 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#33689 = ORIENTED_EDGE ( 'NONE', *, *, #44472, .F. ) ; +#33690 = EDGE_CURVE ( 'NONE', #2083, #71312, #53788, .T. ) ; +#33691 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11945, 'distance_accuracy_value', 'NONE'); +#33692 = ORIENTED_EDGE ( 'NONE', *, *, #5083, .T. ) ; +#33693 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77125, 'distance_accuracy_value', 'NONE'); +#33694 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33695 = LINE ( 'NONE', #2036, #28495 ) ; +#33697 = VECTOR ( 'NONE', #80353, 1000.000000000000000 ) ; +#33696 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#33699 = FILL_AREA_STYLE ('',( #2540 ) ) ; +#33698 = VECTOR ( 'NONE', #43536, 1000.000000000000000 ) ; +#33700 = CARTESIAN_POINT ( 'NONE', ( 1.753807303740889889, -0.9763607356531520676, 0.8100000000000006084 ) ) ; +#33701 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100964 ) ; +#33702 = SURFACE_STYLE_FILL_AREA ( #42860 ) ; +#33703 = ORIENTED_EDGE ( 'NONE', *, *, #19705, .T. ) ; +#33704 = VERTEX_POINT ( 'NONE', #1162 ) ; +#33705 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95601 ), #71147 ) ; +#33706 = LINE ( 'NONE', #35226, #30763 ) ; +#33707 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2816, 'distance_accuracy_value', 'NONE'); +#33708 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.3000000000000016542, -9.095983544939292593E-90 ) ) ; +#33709 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#33710 = CARTESIAN_POINT ( 'NONE', ( -0.9337505133853444272, 2.302534075926971457, 0.8299999999999999600 ) ) ; +#33711 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#33712 = CIRCLE ( 'NONE', #22305, 0.2500000000000001110 ) ; +#33713 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33714 = VECTOR ( 'NONE', #62099, 1000.000000000000114 ) ; +#33715 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#33716 = ORIENTED_EDGE ( 'NONE', *, *, #96774, .T. ) ; +#33717 = ORIENTED_EDGE ( 'NONE', *, *, #51490, .F. ) ; +#33718 = AXIS2_PLACEMENT_3D ( 'NONE', #94033, #93027, #7221 ) ; +#33719 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#33720 = ORIENTED_EDGE ( 'NONE', *, *, #87584, .F. ) ; +#33721 = PRESENTATION_STYLE_ASSIGNMENT (( #79685 ) ) ; +#33722 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#33723 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15737 ), #84281 ) ; +#33724 = FACE_OUTER_BOUND ( 'NONE', #47429, .T. ) ; +#33725 = FACE_OUTER_BOUND ( 'NONE', #12905, .T. ) ; +#33726 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33727 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25630 ), #67922 ) ; +#33728 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33729 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33730 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#33731 = PRESENTATION_STYLE_ASSIGNMENT (( #34744 ) ) ; +#33733 = ORIENTED_EDGE ( 'NONE', *, *, #13633, .T. ) ; +#33732 = ORIENTED_EDGE ( 'NONE', *, *, #58440, .F. ) ; +#33734 = STYLED_ITEM ( 'NONE', ( #61519 ), #4426 ) ; +#33735 = FILL_AREA_STYLE_COLOUR ( '', #95214 ) ; +#33736 = ORIENTED_EDGE ( 'NONE', *, *, #48768, .F. ) ; +#33737 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#33739 = DIRECTION ( 'NONE', ( -0.7071071146859688739, 0.7071064476869688420, 0.000000000000000000 ) ) ; +#33738 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33740 = ORIENTED_EDGE ( 'NONE', *, *, #24659, .F. ) ; +#33741 = ADVANCED_FACE ( 'NONE', ( #14431 ), #16451, .F. ) ; +#33742 = ORIENTED_EDGE ( 'NONE', *, *, #31328, .F. ) ; +#33743 = EDGE_CURVE ( 'NONE', #3083, #2359, #29483, .T. ) ; +#33744 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33745 = SURFACE_STYLE_FILL_AREA ( #56233 ) ; +#33747 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33746 = SURFACE_STYLE_USAGE ( .BOTH. , #96984 ) ; +#33748 = SURFACE_STYLE_USAGE ( .BOTH. , #64871 ) ; +#33749 = EDGE_LOOP ( 'NONE', ( #72024, #34686, #57607, #12043 ) ) ; +#33751 = ORIENTED_EDGE ( 'NONE', *, *, #42071, .F. ) ; +#33750 = VECTOR ( 'NONE', #69783, 1000.000000000000000 ) ; +#33752 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33753 = ORIENTED_EDGE ( 'NONE', *, *, #41270, .F. ) ; +#33754 = CYLINDRICAL_SURFACE ( 'NONE', #24906, 0.009999999999999998473 ) ; +#33756 = ORIENTED_EDGE ( 'NONE', *, *, #90537, .T. ) ; +#33755 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#33757 = EDGE_CURVE ( 'NONE', #43411, #42677, #42546, .T. ) ; +#33758 = LINE ( 'NONE', #1605, #49146 ) ; +#33759 = FACE_OUTER_BOUND ( 'NONE', #99502, .T. ) ; +#33760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33761 = ORIENTED_EDGE ( 'NONE', *, *, #15741, .T. ) ; +#33762 = FILL_AREA_STYLE_COLOUR ( '', #76183 ) ; +#33763 = ORIENTED_EDGE ( 'NONE', *, *, #60780, .T. ) ; +#33764 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48934 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50892, #73363, #57556 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33765 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33766 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#33767 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82659 ) ) ; +#33768 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999995337, 0.1199999999999999956, -0.6500000000000001332 ) ) ; +#33769 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#33770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33771 = PRESENTATION_STYLE_ASSIGNMENT (( #71564 ) ) ; +#33772 = EDGE_CURVE ( 'NONE', #17385, #40015, #11462, .T. ) ; +#33775 = SURFACE_STYLE_FILL_AREA ( #80239 ) ; +#33774 = CARTESIAN_POINT ( 'NONE', ( -0.4927130306483342159, -1.172768239216142927, 0.8299999999999998490 ) ) ; +#33773 = VECTOR ( 'NONE', #47268, 1000.000000000000000 ) ; +#33776 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#33777 = ORIENTED_EDGE ( 'NONE', *, *, #20516, .F. ) ; +#33779 = EDGE_CURVE ( 'NONE', #66631, #61785, #37771, .T. ) ; +#33778 = CARTESIAN_POINT ( 'NONE', ( 1.516559913281009919, -1.413990021526319918, 0.8099999999999982769 ) ) ; +#33780 = AXIS2_PLACEMENT_3D ( 'NONE', #64432, #49123, #10711 ) ; +#33781 = CARTESIAN_POINT ( 'NONE', ( -0.9345478915627419836, -1.069424818316000003, 0.8300000000000000711 ) ) ; +#33782 = VERTEX_POINT ( 'NONE', #92557 ) ; +#33783 = FILL_AREA_STYLE ('',( #73075 ) ) ; +#33784 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74524 ) ) ; +#33786 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, 0.000000000000000000 ) ) ; +#33787 = CARTESIAN_POINT ( 'NONE', ( 0.2757359312880713342, 0.8200000000000000622, -0.1378679656440356671 ) ) ; +#33788 = VECTOR ( 'NONE', #48015, 1000.000000000000000 ) ; +#33790 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#33789 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#33791 = FILL_AREA_STYLE_COLOUR ( '', #92661 ) ; +#33792 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33793 = CLOSED_SHELL ( 'NONE', ( #79404, #73274, #88870, #61364, #57515, #41430, #61210, #60, #52532, #27651, #82162, #66113, #14068, #26146, #42441, #16881, #41775, #18913, #26941, #9987, #11102, #59187, #28538, #88107, #33241, #26972, #47452, #17026, #4082, #25341, #79845, #73677, #12745, #87665, #21490, #43328, #3477, #40163, #45841, #100160, #27195, #91689, #45200, #38470, #50725, #37558, #164, #18283, #95526, #4571, #6820, #54726, #78538, #33938, #25383, #32110, #13831, #80335, #80004, #30463, #1756, #1533, #45191, #3261, #94615, #47077, #83626, #16391, #96290, #75764, #78084, #73922, #15443, #88092, #92823, #50308, #53452, #11839, #31314, #82058, #76147, #94322, #36307, #82140, #88695, #70116, #28947, #12901, #10822, #35125, #30044, #13005, #14625, #35317, #74408, #33410, #73719, #55865, #71318, #82330, #100073, #21667, #39210, #18497, #89991, #54111, #60829, #70970, #82417, #27172, #35654, #39707, #83902, #29912, #34084, #16987, #2128, #87049, #82644, #79354, #43163, #33603, #77027, #3491, #71256, #96211, #81816, #26430, #46488, #41414, #78811, #10496, #6832, #321, #3995, #70656, #76312, #62518, #71078, #71750, #84996, #42176, #77547, #34325, #3545, #47079, #27462, #8062, #51064, #15602, #4434, #87752, #98884, #18949, #11448, #52769, #8375, #71375, #6376, #83777, #20059, #80703, #30566, #5125, #81567, #46271, #19920, #7560, #62206, #57858, #30622, #56243, #20062, #87715, #63304, #54495, #62222, #48409, #31032, #23346, #11272, #5102, #78321, #91726, #4339, #34076, #1894, #77887, #67343, #55666, #27026, #90788, #51532, #83912, #6715, #5992, #55842, #100425, #44802, #27626, #51679, #86521, #15830, #21147, #60631, #88011, #18746, #84304, #6944, #84599, #37824, #92355, #3816, #10660, #10218, #96937, #63752, #44813, #61766, #46830, #6462, #11382, #42149, #30696, #17046, #14844, #76759, #47129, #6921, #73182, #42568, #95707, #74333, #75475, #6761, #19956, #57613, #41954, #92845, #55312, #15692, #66648, #34519, #43150, #13293, #90863, #92370, #514, #83996, #65162, #65290, #35175, #65975, #99421, #44638, #48885, #53835, #69970, #61862, #62478, #66895, #38727, #94978, #56362, #17457, #24948, #15654, #37883, #88896, #76491, #87152, #18506, #48795, #93604, #83991, #79923, #94063, #33741, #24724, #14888, #5888, #31536, #52743, #34023, #41741, #71907, #62528, #59362, #93232, #14267, #20777, #81956, #55333, #35371, #51628, #33354, #51958, #86657, #18154, #100475, #1034, #48712, #83045, #81380, #67017, #99484, #2636, #85890, #37894, #40856, #60844, #95799, #50564, #42027, #93600, #35167, #57362, #13151, #86803, #74890, #86156, #81614, #74683, #37980, #67542, #12781, #38190, #14397, #36135, #2687, #38019, #86682, #52313, #54361, #94727, #30756, #72082, #19122, #29107, #9013, #16474, #35947, #43888, #31398, #51387, #8786, #80194, #9355, #92701, #82798, #89850, #15494, #61815, #37183, #61383, #17004, #23308, #56205, #31527, #75627, #60533, #4645, #36422, #36560, #15348, #87790, #96196, #83928, #19582, #44095, #54611, #43404, #86135, #50138, #80133, #91887, #62203, #3823, #55595, #86870, #85185, #46508, #43847, #33681, #95216, #44878, #33395, #26450, #47382, #14873, #50684, #89741, #84718, #15616, #77095, #25959, #40700, #28932, #43949, #85020, #71595, #11181, #70441, #92398, #96147, #43113, #88247, #60501, #944, #48676, #31909, #41591, #34570, #75635, #44834, #72432, #9053, #61505, #75184, #68978, #4759, #55095, #8860, #12087, #72158, #35926, #76863, #50922, #31899, #82619, #4550, #30418, #48725, #91441, #75546, #5794, #26938, #50539, #17798, #29176, #88215, #67189, #68095, #59506, #67719, #9910, #87504, #60282, #71414, #8281, #18466, #22622, #98000, #20339, #8378, #48160, #96063, #90163, #48258, #97518, #90495, #48037, #19270, #12411, #95035, #42645, #9481, #99628, #6271, #95535, #70976, #76817, #44069, #68945, #68045, #42761, #10889, #38132, #153, #61895, #2038, #33659, #49580, #68269, #20286, #9997, #100326, #49094, #95117, #78597, #37075, #1198, #60138, #14700, #75781, #85934, #51921, #99023, #44760, #55371, #1335, #19202, #28707, #64627, #39153, #68387, #47786, #8946, #32212, #23348, #39019, #80952, #78329, #11218, #91222, #3553, #52504, #54587, #73722, #68712, #48872, #45620, #55718, #77770, #68189, #68200, #69349, #72279, #63583, #13613, #55683, #3383, #73889, #87064, #14155, #33310, #12152, #94777, #98537, #80741, #39348, #65898, #62684, #18912, #15066, #58103, #46304, #55169, #18389, #45128, #8152, #38166, #30444, #5256, #52520, #76955, #41366, #100806, #65307, #69365, #1326, #19030, #19299, #6615, #42416, #99568, #2198, #25801, #71429, #25497, #98091, #37322, #38665, #82000, #62293, #82012, #35157, #36508, #89605, #70576, #68351, #26027, #77102, #57148, #41784, #92883, #20737, #5492, #20688, #42855, #2596, #36354, #7684, #98018, #43122, #86305, #29524, #87094, #51254, #47058, #26831, #53365, #38206, #99658, #36608, #75109, #82537, #82005, #64901, #52433, #53783, #92019, #16309 ) ) ; +#33794 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20100, #89073, #80928, #73744, #27814, #58965, #12375, #90056, #3793, #35474, #10865, #43094, #74754 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000026645, 0.2500000000000053291, 0.3750000000000079936, 0.4375000000000081046, 0.5000000000000082157, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#33795 = VECTOR ( 'NONE', #27690, 1000.000000000000000 ) ; +#33796 = SURFACE_STYLE_FILL_AREA ( #47580 ) ; +#33797 = VECTOR ( 'NONE', #6125, 1000.000000000000000 ) ; +#33798 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33799 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#33800 = VECTOR ( 'NONE', #61769, 1000.000000000000000 ) ; +#33801 = ORIENTED_EDGE ( 'NONE', *, *, #833, .T. ) ; +#33802 = ADVANCED_FACE ( 'NONE', ( #78291 ), #39467, .T. ) ; +#33803 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#33804 = PRESENTATION_STYLE_ASSIGNMENT (( #2647 ) ) ; +#33805 = SURFACE_SIDE_STYLE ('',( #72090 ) ) ; +#33806 = AXIS2_PLACEMENT_3D ( 'NONE', #59386, #41522, #96608 ) ; +#33807 = ORIENTED_EDGE ( 'NONE', *, *, #95999, .F. ) ; +#33808 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33809 = EDGE_CURVE ( 'NONE', #33492, #30045, #57862, .T. ) ; +#33810 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 5.267127000000001225, 0.8648700000000000276 ) ) ; +#33811 = SURFACE_STYLE_FILL_AREA ( #19970 ) ; +#33812 = SURFACE_STYLE_USAGE ( .BOTH. , #27168 ) ; +#33814 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#33813 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59718 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75384, #91691, #24183 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33815 = EDGE_CURVE ( 'NONE', #100360, #75172, #41501, .T. ) ; +#33816 = AXIS2_PLACEMENT_3D ( 'NONE', #19188, #25884, #49871 ) ; +#33817 = SURFACE_STYLE_USAGE ( .BOTH. , #41472 ) ; +#33818 = LINE ( 'NONE', #35345, #43099 ) ; +#33819 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33820 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63861, 'distance_accuracy_value', 'NONE'); +#33821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6035 ) ) ; +#33822 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33823 = ORIENTED_EDGE ( 'NONE', *, *, #52042, .F. ) ; +#33824 = EDGE_CURVE ( 'NONE', #88976, #54104, #88966, .T. ) ; +#33825 = ORIENTED_EDGE ( 'NONE', *, *, #12759, .T. ) ; +#33826 = SURFACE_STYLE_USAGE ( .BOTH. , #41985 ) ; +#33827 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90044, 'distance_accuracy_value', 'NONE'); +#33828 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13750, 'distance_accuracy_value', 'NONE'); +#33829 = SURFACE_STYLE_FILL_AREA ( #18975 ) ; +#33830 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#33831 = CARTESIAN_POINT ( 'NONE', ( -0.2052975279651420015, -1.010243534007990052, 0.8100000000000000533 ) ) ; +#33832 = LINE ( 'NONE', #27688, #31450 ) ; +#33833 = VECTOR ( 'NONE', #57706, 999.9999999999998863 ) ; +#33834 = FILL_AREA_STYLE_COLOUR ( '', #10799 ) ; +#33835 = FILL_AREA_STYLE ('',( #33327 ) ) ; +#33836 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#33837 = EDGE_LOOP ( 'NONE', ( #75996, #93930, #13276, #37362, #75014, #35129 ) ) ; +#33838 = LINE ( 'NONE', #88440, #23252 ) ; +#33839 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, 3.123820061220075051, 0.000000000000000000 ) ) ; +#33840 = SURFACE_STYLE_FILL_AREA ( #41492 ) ; +#33841 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.000000000000000000 ) ) ; +#33842 = VERTEX_POINT ( 'NONE', #96084 ) ; +#33843 = FILL_AREA_STYLE_COLOUR ( '', #92975 ) ; +#33844 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000052403, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#33845 = STYLED_ITEM ( 'NONE', ( #19949 ), #79274 ) ; +#33846 = ORIENTED_EDGE ( 'NONE', *, *, #87890, .T. ) ; +#33847 = EDGE_CURVE ( 'NONE', #58587, #30045, #41013, .T. ) ; +#33848 = EDGE_CURVE ( 'NONE', #59623, #4442, #10241, .T. ) ; +#33849 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#33850 = AXIS2_PLACEMENT_3D ( 'NONE', #84575, #92706, #22293 ) ; +#33851 = PRESENTATION_STYLE_ASSIGNMENT (( #11753 ) ) ; +#33852 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33854 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33853 = VECTOR ( 'NONE', #19594, 1000.000000000000000 ) ; +#33855 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#33856 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33857 = VERTEX_POINT ( 'NONE', #25201 ) ; +#33858 = AXIS2_PLACEMENT_3D ( 'NONE', #70064, #45540, #60942 ) ; +#33859 = VERTEX_POINT ( 'NONE', #87446 ) ; +#33860 = AXIS2_PLACEMENT_3D ( 'NONE', #29782, #60963, #92071 ) ; +#33861 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6067 ), #56685 ) ; +#33862 = CLOSED_SHELL ( 'NONE', ( #98313, #25623, #30921, #54659, #39514, #91878 ) ) ; +#33863 = EDGE_CURVE ( 'NONE', #83944, #17922, #86622, .T. ) ; +#33864 = ORIENTED_EDGE ( 'NONE', *, *, #40136, .T. ) ; +#33865 = EDGE_CURVE ( 'NONE', #93886, #33859, #73148, .T. ) ; +#33866 = AXIS2_PLACEMENT_3D ( 'NONE', #7091, #86298, #8098 ) ; +#33867 = LINE ( 'NONE', #64986, #87291 ) ; +#33868 = FILL_AREA_STYLE ('',( #3207 ) ) ; +#33869 = FILL_AREA_STYLE_COLOUR ( '', #53561 ) ; +#33870 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402591606, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#33872 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33871 = CARTESIAN_POINT ( 'NONE', ( 0.2667602038132769748, -1.009329072279059991, 0.8299999999999999600 ) ) ; +#33874 = ORIENTED_EDGE ( 'NONE', *, *, #89539, .T. ) ; +#33873 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7212 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90511, #47057, #14866 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33876 = ORIENTED_EDGE ( 'NONE', *, *, #80544, .T. ) ; +#33875 = ORIENTED_EDGE ( 'NONE', *, *, #66828, .F. ) ; +#33877 = FACE_OUTER_BOUND ( 'NONE', #49073, .T. ) ; +#33878 = ORIENTED_EDGE ( 'NONE', *, *, #27724, .T. ) ; +#33879 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44448 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45258, #67755, #14607 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33880 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2849999999999999756, 0.1399999999999965994 ) ) ; +#33881 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#33882 = EDGE_LOOP ( 'NONE', ( #35960, #82104, #32086, #60000 ) ) ; +#33885 = ORIENTED_EDGE ( 'NONE', *, *, #11944, .T. ) ; +#33884 = VECTOR ( 'NONE', #8459, 1000.000000000000000 ) ; +#33883 = DIRECTION ( 'NONE', ( 0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#33886 = EDGE_CURVE ( 'NONE', #82725, #32383, #96141, .T. ) ; +#33887 = FILL_AREA_STYLE_COLOUR ( '', #96452 ) ; +#33888 = PLANE ( 'NONE', #81930 ) ; +#33889 = LINE ( 'NONE', #65010, #25961 ) ; +#33890 = ORIENTED_EDGE ( 'NONE', *, *, #82874, .T. ) ; +#33891 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#33892 = PRESENTATION_STYLE_ASSIGNMENT (( #47160 ) ) ; +#33893 = LINE ( 'NONE', #64511, #80268 ) ; +#33894 = VERTEX_POINT ( 'NONE', #10752 ) ; +#33895 = SURFACE_STYLE_USAGE ( .BOTH. , #65498 ) ; +#33896 = ADVANCED_FACE ( 'NONE', ( #95073 ), #2195, .T. ) ; +#33897 = CYLINDRICAL_SURFACE ( 'NONE', #49728, 0.1100000000000007222 ) ; +#33898 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33899 = AXIS2_PLACEMENT_3D ( 'NONE', #56723, #94462, #87320 ) ; +#33900 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#33901 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33902 = SURFACE_SIDE_STYLE ('',( #25250 ) ) ; +#33903 = ADVANCED_FACE ( 'NONE', ( #12272 ), #66973, .T. ) ; +#33904 = PRESENTATION_STYLE_ASSIGNMENT (( #49730 ) ) ; +#33905 = CARTESIAN_POINT ( 'NONE', ( 0.1681044570581656239, 0.4876707056443637667, 0.8100000000000000533 ) ) ; +#33906 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33908 = ADVANCED_FACE ( 'NONE', ( #82808 ), #4193, .F. ) ; +#33907 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33909 = SURFACE_STYLE_USAGE ( .BOTH. , #63035 ) ; +#33910 = VECTOR ( 'NONE', #78863, 1000.000000000000000 ) ; +#33911 = SURFACE_SIDE_STYLE ('',( #1755 ) ) ; +#33912 = LINE ( 'NONE', #4736, #51071 ) ; +#33913 = AXIS2_PLACEMENT_3D ( 'NONE', #69818, #71350, #47362 ) ; +#33914 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#33915 = CARTESIAN_POINT ( 'NONE', ( -1.132954166604120072, -0.8848558980161149723, 0.8100000000000000533 ) ) ; +#33916 = FILL_AREA_STYLE ('',( #72696 ) ) ; +#33917 = ORIENTED_EDGE ( 'NONE', *, *, #68236, .T. ) ; +#33918 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#33919 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#33920 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000140062184, -0.6499999999789451977 ) ) ; +#33921 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#33922 = VECTOR ( 'NONE', #4834, 1000.000000000000000 ) ; +#33923 = VERTEX_POINT ( 'NONE', #27700 ) ; +#33924 = FACE_OUTER_BOUND ( 'NONE', #34859, .T. ) ; +#33925 = EDGE_CURVE ( 'NONE', #69995, #92420, #58359, .T. ) ; +#33926 = VECTOR ( 'NONE', #64441, 1000.000000000000000 ) ; +#33927 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68123 ), #1316 ) ; +#33928 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#33929 = CARTESIAN_POINT ( 'NONE', ( 1.581953864252920283, -1.079063990458370093, 0.8299999999999999600 ) ) ; +#33930 = CARTESIAN_POINT ( 'NONE', ( -0.2325713810860060016, -1.366783821657739928, 0.8100000000000000533 ) ) ; +#33931 = FILL_AREA_STYLE_COLOUR ( '', #78962 ) ; +#33932 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29017 ), #61690 ) ; +#33933 = VECTOR ( 'NONE', #95456, 1000.000000000000000 ) ; +#33934 = VECTOR ( 'NONE', #60596, 1000.000000000000000 ) ; +#33935 = SURFACE_SIDE_STYLE ('',( #3770 ) ) ; +#33936 = CLOSED_SHELL ( 'NONE', ( #6396, #42631, #31728, #36909, #7969, #63617 ) ) ; +#33937 = ORIENTED_EDGE ( 'NONE', *, *, #91947, .T. ) ; +#33938 = ADVANCED_FACE ( 'NONE', ( #83815 ), #17940, .F. ) ; +#33939 = LINE ( 'NONE', #57418, #75163 ) ; +#33940 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77925 ), #46938 ) ; +#33941 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#33942 = CARTESIAN_POINT ( 'NONE', ( 1.080509293578989949, -0.9076590548536891401, 0.8299999999999994049 ) ) ; +#33943 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.300000000000000266, -0.02000000000002793293 ) ) ; +#33944 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#33945 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100679 ), #29035 ) ; +#33946 = EDGE_CURVE ( 'NONE', #51814, #72506, #93437, .T. ) ; +#33947 = FILL_AREA_STYLE ('',( #2781 ) ) ; +#33948 = SURFACE_STYLE_USAGE ( .BOTH. , #18578 ) ; +#33949 = LINE ( 'NONE', #57428, #65992 ) ; +#33950 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1787, 'distance_accuracy_value', 'NONE'); +#33951 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63329 ) ) ; +#33952 = CARTESIAN_POINT ( 'NONE', ( 1.130331698131229912, -1.432449005990829916, 0.8299999999999999600 ) ) ; +#33953 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33954 = PLANE ( 'NONE', #89523 ) ; +#33955 = ORIENTED_EDGE ( 'NONE', *, *, #68804, .F. ) ; +#33956 = EDGE_CURVE ( 'NONE', #36910, #23866, #93927, .T. ) ; +#33957 = ORIENTED_EDGE ( 'NONE', *, *, #99893, .T. ) ; +#33958 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90857, 'distance_accuracy_value', 'NONE'); +#33959 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18450, 'distance_accuracy_value', 'NONE'); +#33960 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#33961 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#33962 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33963 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#33964 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33965 = FACE_OUTER_BOUND ( 'NONE', #32989, .T. ) ; +#33966 = FILL_AREA_STYLE ('',( #10868 ) ) ; +#33967 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33968 = ORIENTED_EDGE ( 'NONE', *, *, #55269, .T. ) ; +#33969 = FILL_AREA_STYLE_COLOUR ( '', #95952 ) ; +#33970 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20958, 'distance_accuracy_value', 'NONE'); +#33971 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#33972 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #95598, .NOT_KNOWN. ) ; +#33973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#33974 = AXIS2_PLACEMENT_3D ( 'NONE', #84212, #100402, #77045 ) ; +#33975 = ORIENTED_EDGE ( 'NONE', *, *, #100682, .F. ) ; +#33976 = SURFACE_SIDE_STYLE ('',( #26307 ) ) ; +#33977 = EDGE_CURVE ( 'NONE', #28211, #29762, #29668, .T. ) ; +#33978 = EDGE_CURVE ( 'NONE', #25581, #44430, #6627, .T. ) ; +#33979 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#33980 = LINE ( 'NONE', #40114, #81561 ) ; +#33981 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#33982 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#33983 = ORIENTED_EDGE ( 'NONE', *, *, #4271, .T. ) ; +#33984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64126 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38872, #70502, #2590 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#33985 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72829, 'distance_accuracy_value', 'NONE'); +#33987 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000637737685, 0.000000000000000000 ) ) ; +#33986 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6184 ), #4565 ) ; +#33988 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#33989 = FILL_AREA_STYLE ('',( #65102 ) ) ; +#33990 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100730 ), #38982 ) ; +#33991 = EDGE_LOOP ( 'NONE', ( #43253, #80706, #89487, #14499 ) ) ; +#33992 = EDGE_CURVE ( 'NONE', #68594, #49420, #85810, .T. ) ; +#33993 = SURFACE_SIDE_STYLE ('',( #26832 ) ) ; +#33994 = SURFACE_STYLE_FILL_AREA ( #18099 ) ; +#33995 = VECTOR ( 'NONE', #73582, 1000.000000000000000 ) ; +#33996 = CARTESIAN_POINT ( 'NONE', ( -1.320173117493106618, -1.167080940716315629, 0.8099999999998648281 ) ) ; +#33997 = PRESENTATION_STYLE_ASSIGNMENT (( #2830 ) ) ; +#33998 = VECTOR ( 'NONE', #76109, 1000.000000000000000 ) ; +#33999 = STYLED_ITEM ( 'NONE', ( #36048 ), #944 ) ; +#34000 = ORIENTED_EDGE ( 'NONE', *, *, #30477, .F. ) ; +#34001 = ORIENTED_EDGE ( 'NONE', *, *, #45106, .F. ) ; +#34002 = VECTOR ( 'NONE', #13007, 1000.000000000000000 ) ; +#34003 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34004 = VECTOR ( 'NONE', #3586, 1000.000000000000000 ) ; +#34005 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, 0.3000000000000000999 ) ) ; +#34006 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#34007 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34008 = CLOSED_SHELL ( 'NONE', ( #20942, #64322, #18960, #7776, #90610, #53775 ) ) ; +#34009 = SURFACE_SIDE_STYLE ('',( #94356 ) ) ; +#34010 = PRESENTATION_STYLE_ASSIGNMENT (( #41659 ) ) ; +#34011 = ORIENTED_EDGE ( 'NONE', *, *, #13141, .F. ) ; +#34012 = FACE_OUTER_BOUND ( 'NONE', #79194, .T. ) ; +#34013 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34014 = ORIENTED_EDGE ( 'NONE', *, *, #9861, .F. ) ; +#34015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69823 ), #21017 ) ; +#34016 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#34017 = EDGE_LOOP ( 'NONE', ( #66565, #9298, #96357, #125 ) ) ; +#34018 = ORIENTED_EDGE ( 'NONE', *, *, #81336, .T. ) ; +#34019 = LINE ( 'NONE', #17139, #49437 ) ; +#34020 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#34021 = AXIS2_PLACEMENT_3D ( 'NONE', #65148, #88622, #41683 ) ; +#34023 = ADVANCED_FACE ( 'NONE', ( #47005 ), #8112, .F. ) ; +#34022 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#34024 = ORIENTED_EDGE ( 'NONE', *, *, #99441, .T. ) ; +#34025 = STYLED_ITEM ( 'NONE', ( #17337 ), #44026 ) ; +#34026 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34027 = ORIENTED_EDGE ( 'NONE', *, *, #37709, .T. ) ; +#34028 = CARTESIAN_POINT ( 'NONE', ( 1.363204453251209980, -1.351484773706350007, 0.8299999999999999600 ) ) ; +#34029 = FILL_AREA_STYLE_COLOUR ( '', #41345 ) ; +#34030 = EDGE_CURVE ( 'NONE', #46370, #23447, #9136, .T. ) ; +#34031 = ORIENTED_EDGE ( 'NONE', *, *, #31116, .F. ) ; +#34033 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.1000000000000013378, 0.1829999999999709359 ) ) ; +#34032 = SURFACE_STYLE_USAGE ( .BOTH. , #95755 ) ; +#34034 = CARTESIAN_POINT ( 'NONE', ( -1.355486452235469930, -1.128484622308769891, 0.8299999999999999600 ) ) ; +#34035 = FACE_OUTER_BOUND ( 'NONE', #83850, .T. ) ; +#34036 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12731 ) ) ; +#34037 = VECTOR ( 'NONE', #4460, 1000.000000000000000 ) ; +#34038 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#34039 = CARTESIAN_POINT ( 'NONE', ( 1.263543985521710100, -0.9656714926165439472, 0.8299999999999999600 ) ) ; +#34040 = STYLED_ITEM ( 'NONE', ( #63846 ), #92398 ) ; +#34041 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34042 = ORIENTED_EDGE ( 'NONE', *, *, #58201, .F. ) ; +#34043 = LINE ( 'NONE', #35558, #37135 ) ; +#34044 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#34045 = ADVANCED_FACE ( 'NONE', ( #2076 ), #42683, .T. ) ; +#34047 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34046 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34048 = VECTOR ( 'NONE', #70369, 1000.000000000000000 ) ; +#34049 = PRESENTATION_STYLE_ASSIGNMENT (( #96779 ) ) ; +#34050 = SURFACE_SIDE_STYLE ('',( #17673 ) ) ; +#34051 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47379 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50799, #76244, #99147 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34052 = CIRCLE ( 'NONE', #91091, 0.009999999999999998473 ) ; +#34053 = LINE ( 'NONE', #25392, #67916 ) ; +#34054 = PLANE ( 'NONE', #90940 ) ; +#34055 = PLANE ( 'NONE', #54256 ) ; +#34056 = ORIENTED_EDGE ( 'NONE', *, *, #84671, .T. ) ; +#34057 = EDGE_CURVE ( 'NONE', #94230, #81873, #40379, .T. ) ; +#34058 = SURFACE_STYLE_FILL_AREA ( #42701 ) ; +#34059 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#34060 = SURFACE_SIDE_STYLE ('',( #74355 ) ) ; +#34061 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.500000000000000000, 0.000000000000000000 ) ) ; +#34062 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75633, 'distance_accuracy_value', 'NONE'); +#34063 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.000000000000000000 ) ) ; +#34064 = LINE ( 'NONE', #8063, #21266 ) ; +#34065 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.05000000000000000278, 0.1900000000000000022 ) ) ; +#34066 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.1000000000000000056, -12.01999999999999957 ) ) ; +#34067 = LINE ( 'NONE', #72856, #18124 ) ; +#34068 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -9.900934239137630374E-18, 0.2499999999999998890 ) ) ; +#34069 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34071 = VECTOR ( 'NONE', #14030, 1000.000000000000000 ) ; +#34070 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#34072 = LINE ( 'NONE', #41721, #21048 ) ; +#34073 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#34074 = VECTOR ( 'NONE', #91028, 1000.000000000000000 ) ; +#34075 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34076 = ADVANCED_FACE ( 'NONE', ( #96464 ), #57227, .F. ) ; +#34077 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34078 = SURFACE_SIDE_STYLE ('',( #89186 ) ) ; +#34079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34080 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34081 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34082 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #56088, 'design' ) ; +#34084 = ADVANCED_FACE ( 'NONE', ( #17362 ), #82460, .F. ) ; +#34083 = SURFACE_SIDE_STYLE ('',( #2923 ) ) ; +#34085 = CYLINDRICAL_SURFACE ( 'NONE', #54122, 0.05000000000000012768 ) ; +#34086 = ORIENTED_EDGE ( 'NONE', *, *, #33160, .T. ) ; +#34087 = FACE_OUTER_BOUND ( 'NONE', #62511, .T. ) ; +#34088 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.299999999999999822, 1.084224129406308774E-78 ) ) ; +#34089 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68060, 'distance_accuracy_value', 'NONE'); +#34090 = PLANE ( 'NONE', #286 ) ; +#34091 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74076, 'distance_accuracy_value', 'NONE'); +#34093 = PRESENTATION_STYLE_ASSIGNMENT (( #17212 ) ) ; +#34092 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34094 = VECTOR ( 'NONE', #21579, 1000.000000000000114 ) ; +#34095 = CARTESIAN_POINT ( 'NONE', ( 1.876179938779914957, 3.099999999999970335, 0.000000000000000000 ) ) ; +#34096 = ADVANCED_FACE ( 'NONE', ( #51066 ), #75521, .T. ) ; +#34097 = EDGE_CURVE ( 'NONE', #65417, #46536, #100867, .T. ) ; +#34098 = PRESENTATION_STYLE_ASSIGNMENT (( #56582 ) ) ; +#34099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65049 ) ) ; +#34100 = EDGE_LOOP ( 'NONE', ( #41275, #44493, #23732, #68355 ) ) ; +#34101 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#34102 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34103 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34104 = EDGE_CURVE ( 'NONE', #96973, #85273, #37732, .T. ) ; +#34105 = EDGE_CURVE ( 'NONE', #56612, #16866, #100382, .T. ) ; +#34106 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58072, 'distance_accuracy_value', 'NONE'); +#34107 = FILL_AREA_STYLE_COLOUR ( '', #42937 ) ; +#34108 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16006, 'distance_accuracy_value', 'NONE'); +#34109 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34110 = FILL_AREA_STYLE ('',( #1932 ) ) ; +#34111 = ORIENTED_EDGE ( 'NONE', *, *, #99827, .F. ) ; +#34112 = EDGE_LOOP ( 'NONE', ( #30297, #5581, #62268, #46599, #78562, #46628 ) ) ; +#34113 = EDGE_CURVE ( 'NONE', #13767, #88894, #92334, .T. ) ; +#34114 = SURFACE_SIDE_STYLE ('',( #56600 ) ) ; +#34115 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#34116 = AXIS2_PLACEMENT_3D ( 'NONE', #85023, #15034, #46192 ) ; +#34117 = ORIENTED_EDGE ( 'NONE', *, *, #47627, .T. ) ; +#34118 = SURFACE_STYLE_FILL_AREA ( #2951 ) ; +#34119 = LINE ( 'NONE', #96341, #95373 ) ; +#34120 = EDGE_CURVE ( 'NONE', #85953, #17076, #23410, .T. ) ; +#34121 = AXIS2_PLACEMENT_3D ( 'NONE', #21198, #22206, #5339 ) ; +#34122 = CIRCLE ( 'NONE', #71639, 1.319494367338009955 ) ; +#34123 = PRODUCT_CONTEXT ( 'NONE', #99633, 'mechanical' ) ; +#34124 = FILL_AREA_STYLE ('',( #2957 ) ) ; +#34126 = ORIENTED_EDGE ( 'NONE', *, *, #65152, .F. ) ; +#34125 = ORIENTED_EDGE ( 'NONE', *, *, #61178, .T. ) ; +#34127 = ORIENTED_EDGE ( 'NONE', *, *, #36205, .F. ) ; +#34128 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34129 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84590 ), #61809 ) ; +#34130 = STYLED_ITEM ( 'NONE', ( #4297 ), #92019 ) ; +#34131 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.6999999999999988454, 0.8299999999999999600 ) ) ; +#34132 = ORIENTED_EDGE ( 'NONE', *, *, #98949, .F. ) ; +#34133 = VECTOR ( 'NONE', #75356, 1000.000000000000000 ) ; +#34134 = AXIS2_PLACEMENT_3D ( 'NONE', #27437, #90716, #12527 ) ; +#34135 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#34136 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50227, #17998, #25235, #18524 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#34137 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571430157, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#34138 = ORIENTED_EDGE ( 'NONE', *, *, #35795, .F. ) ; +#34139 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#34140 = EDGE_LOOP ( 'NONE', ( #20768, #28915, #53335, #4090 ) ) ; +#34141 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34142 = VERTEX_POINT ( 'NONE', #6988 ) ; +#34143 = VERTEX_POINT ( 'NONE', #21899 ) ; +#34144 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65096, #79937, #87080, #48301 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#34145 = PLANE ( 'NONE', #28680 ) ; +#34146 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81457 ), #47149 ) ; +#34147 = PRESENTATION_STYLE_ASSIGNMENT (( #81109 ) ) ; +#34148 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34150 = EDGE_CURVE ( 'NONE', #48584, #84311, #76023, .T. ) ; +#34149 = SURFACE_SIDE_STYLE ('',( #27988 ) ) ; +#34152 = VERTEX_POINT ( 'NONE', #85175 ) ; +#34151 = CARTESIAN_POINT ( 'NONE', ( 11.10544712487501329, 4.680228875124988086, 0.8648700000000000276 ) ) ; +#34153 = AXIS2_PLACEMENT_3D ( 'NONE', #13912, #25671, #71115 ) ; +#34154 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.1000000000000016015, 0.000000000000000000 ) ) ; +#34155 = CARTESIAN_POINT ( 'NONE', ( -0.1330377395154810072, -0.9004049383407729534, 0.8100000000000000533 ) ) ; +#34156 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -0.9000000000000019096, 0.1829999999999620541 ) ) ; +#34157 = ORIENTED_EDGE ( 'NONE', *, *, #46819, .T. ) ; +#34159 = LINE ( 'NONE', #65262, #87708 ) ; +#34158 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34160 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43884 ) ) ; +#34161 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#34162 = ORIENTED_EDGE ( 'NONE', *, *, #100440, .F. ) ; +#34163 = EDGE_CURVE ( 'NONE', #40015, #51666, #418, .T. ) ; +#34164 = VERTEX_POINT ( 'NONE', #92798 ) ; +#34166 = PRESENTATION_STYLE_ASSIGNMENT (( #96384 ) ) ; +#34165 = FILL_AREA_STYLE_COLOUR ( '', #94515 ) ; +#34167 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#34168 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 6.650000000000000355, 0.000000000000000000 ) ) ; +#34169 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#34170 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96127 ) ) ; +#34171 = SURFACE_SIDE_STYLE ('',( #88763 ) ) ; +#34172 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#34173 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43355 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22117, #6229, #36948 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34174 = ORIENTED_EDGE ( 'NONE', *, *, #1491, .F. ) ; +#34175 = FACE_OUTER_BOUND ( 'NONE', #72155, .T. ) ; +#34176 = VERTEX_POINT ( 'NONE', #54054 ) ; +#34177 = CARTESIAN_POINT ( 'NONE', ( -0.2166666666666656749, -3.099999999999980549, 0.000000000000000000 ) ) ; +#34178 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9238200612200859752, -0.02000000000000000042 ) ) ; +#34179 = STYLED_ITEM ( 'NONE', ( #30918 ), #44494 ) ; +#34180 = CARTESIAN_POINT ( 'NONE', ( 1.314694272500980032, -1.181578794826660284, 0.8299999999999999600 ) ) ; +#34181 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34182 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34183 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#34184 = EDGE_LOOP ( 'NONE', ( #40066, #79200, #54339, #45259 ) ) ; +#34185 = EDGE_CURVE ( 'NONE', #82814, #100499, #15717, .T. ) ; +#34186 = PLANE ( 'NONE', #85157 ) ; +#34187 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34188 = SURFACE_STYLE_USAGE ( .BOTH. , #95910 ) ; +#34189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#34190 = SURFACE_STYLE_USAGE ( .BOTH. , #48998 ) ; +#34191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34192 = VECTOR ( 'NONE', #55861, 1000.000000000000000 ) ; +#34193 = SURFACE_STYLE_USAGE ( .BOTH. , #97415 ) ; +#34194 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34195 = AXIS2_PLACEMENT_3D ( 'NONE', #55669, #32173, #54134 ) ; +#34196 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#34197 = LINE ( 'NONE', #56677, #4377 ) ; +#34198 = LINE ( 'NONE', #26526, #32237 ) ; +#34199 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2749999999999999667, 0.1399999999999999856 ) ) ; +#34200 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61951 ), #91227 ) ; +#34201 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34202 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34203 = DIRECTION ( 'NONE', ( 0.7071067806865475314, -0.7071067816865476141, 0.000000000000000000 ) ) ; +#34204 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40241, 'distance_accuracy_value', 'NONE'); +#34205 = VERTEX_POINT ( 'NONE', #30523 ) ; +#34206 = FILL_AREA_STYLE ('',( #96934 ) ) ; +#34207 = CARTESIAN_POINT ( 'NONE', ( 1.617430281440370043, -0.9137302873894740385, 0.8299999999999999600 ) ) ; +#34208 = FACE_OUTER_BOUND ( 'NONE', #98555, .T. ) ; +#34209 = ORIENTED_EDGE ( 'NONE', *, *, #69000, .F. ) ; +#34210 = SURFACE_SIDE_STYLE ('',( #19859 ) ) ; +#34211 = FILL_AREA_STYLE_COLOUR ( '', #42057 ) ; +#34212 = SURFACE_STYLE_FILL_AREA ( #56693 ) ; +#34213 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#34214 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74761 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8191, #38426, #54784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34215 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.076179938779915135, -0.02000000000000000042 ) ) ; +#34216 = CARTESIAN_POINT ( 'NONE', ( 1.776971753240009999, -0.9939892240680031632, 0.8100000000000006084 ) ) ; +#34217 = FILL_AREA_STYLE_COLOUR ( '', #95545 ) ; +#34218 = VECTOR ( 'NONE', #94640, 1000.000000000000000 ) ; +#34219 = ORIENTED_EDGE ( 'NONE', *, *, #26882, .T. ) ; +#34220 = ORIENTED_EDGE ( 'NONE', *, *, #64595, .F. ) ; +#34221 = AXIS2_PLACEMENT_3D ( 'NONE', #75968, #60666, #100329 ) ; +#34222 = PLANE ( 'NONE', #50439 ) ; +#34223 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#34224 = SURFACE_STYLE_FILL_AREA ( #10604 ) ; +#34225 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#34226 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34227 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34228 = SURFACE_STYLE_USAGE ( .BOTH. , #80687 ) ; +#34229 = FILL_AREA_STYLE ('',( #88824 ) ) ; +#34230 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34231 = LINE ( 'NONE', #49033, #47859 ) ; +#34232 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#34233 = LINE ( 'NONE', #9623, #70615 ) ; +#34234 = ORIENTED_EDGE ( 'NONE', *, *, #32769, .F. ) ; +#34235 = FILL_AREA_STYLE_COLOUR ( '', #84608 ) ; +#34236 = ORIENTED_EDGE ( 'NONE', *, *, #97914, .F. ) ; +#34238 = CARTESIAN_POINT ( 'NONE', ( -0.8280235389610389740, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#34237 = AXIS2_PLACEMENT_3D ( 'NONE', #78598, #63330, #49002 ) ; +#34239 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34240 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78237 ) ) ; +#34241 = CARTESIAN_POINT ( 'NONE', ( -0.9938630133853425530, 2.355709075926969653, 0.8100000000000000533 ) ) ; +#34242 = EDGE_CURVE ( 'NONE', #13813, #48405, #6509, .T. ) ; +#34243 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34246 = ORIENTED_EDGE ( 'NONE', *, *, #95750, .F. ) ; +#34245 = EDGE_LOOP ( 'NONE', ( #73784, #51473, #17637, #88125 ) ) ; +#34247 = LINE ( 'NONE', #73535, #89232 ) ; +#34248 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40865 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89585, #60475, #58487 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34249 = EDGE_LOOP ( 'NONE', ( #7904, #69601, #50229, #13212 ) ) ; +#34250 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.876179938779915179, -0.02000000000000000042 ) ) ; +#34252 = PRESENTATION_STYLE_ASSIGNMENT (( #3082 ) ) ; +#34251 = LINE ( 'NONE', #88345, #14617 ) ; +#34253 = VERTEX_POINT ( 'NONE', #30042 ) ; +#34254 = ORIENTED_EDGE ( 'NONE', *, *, #83082, .F. ) ; +#34255 = SURFACE_STYLE_FILL_AREA ( #11155 ) ; +#34256 = SURFACE_STYLE_USAGE ( .BOTH. , #49569 ) ; +#34257 = SURFACE_STYLE_FILL_AREA ( #9649 ) ; +#34258 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.600000000000000089, -13.40000000000000036 ) ) ; +#34260 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, 0.000000000000000000 ) ) ; +#34259 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34261 = SURFACE_STYLE_FILL_AREA ( #3090 ) ; +#34262 = ORIENTED_EDGE ( 'NONE', *, *, #94350, .F. ) ; +#34263 = ORIENTED_EDGE ( 'NONE', *, *, #59482, .T. ) ; +#34264 = SURFACE_STYLE_FILL_AREA ( #32741 ) ; +#34265 = EDGE_LOOP ( 'NONE', ( #41814, #40751, #90481, #13436 ) ) ; +#34266 = FILL_AREA_STYLE_COLOUR ( '', #33470 ) ; +#34267 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34268 = VECTOR ( 'NONE', #5183, 1000.000000000000000 ) ; +#34269 = EDGE_CURVE ( 'NONE', #91950, #24157, #84190, .T. ) ; +#34270 = VECTOR ( 'NONE', #19812, 1000.000000000000000 ) ; +#34272 = ORIENTED_EDGE ( 'NONE', *, *, #33946, .F. ) ; +#34271 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34273 = VECTOR ( 'NONE', #57984, 1000.000000000000000 ) ; +#34274 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34040 ) ) ; +#34275 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#34276 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30951 ) ) ; +#34277 = SURFACE_STYLE_FILL_AREA ( #34778 ) ; +#34278 = ORIENTED_EDGE ( 'NONE', *, *, #74519, .T. ) ; +#34279 = STYLED_ITEM ( 'NONE', ( #84604 ), #81567 ) ; +#34280 = CARTESIAN_POINT ( 'NONE', ( -1.063092585139040036, -1.436993929120638613, 0.8099999999996658762 ) ) ; +#34281 = ORIENTED_EDGE ( 'NONE', *, *, #45015, .T. ) ; +#34282 = EDGE_CURVE ( 'NONE', #78446, #78170, #53556, .T. ) ; +#34283 = PRESENTATION_STYLE_ASSIGNMENT (( #63535 ) ) ; +#34284 = VECTOR ( 'NONE', #53063, 1000.000000000000000 ) ; +#34285 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.000000000000000000 ) ) ; +#34286 = CARTESIAN_POINT ( 'NONE', ( 0.2416657235478834875, -1.089245064413529196, 0.8099999999999998312 ) ) ; +#34288 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, 3.149999999999979927, 0.000000000000000000 ) ) ; +#34287 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95066 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96037, #57816, #2648 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34289 = DIRECTION ( 'NONE', ( 0.7071067811865483499, 0.7071067811865465735, 0.000000000000000000 ) ) ; +#34290 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78285 ), #83385 ) ; +#34291 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #88465, #82894 ), #63115 ) ; +#34292 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34293 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34294 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, -3.500000000000000444, 0.000000000000000000 ) ) ; +#34295 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67548 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14626, #85620, #53491 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34296 = ORIENTED_EDGE ( 'NONE', *, *, #59391, .F. ) ; +#34297 = CARTESIAN_POINT ( 'NONE', ( 1.502791041020159923, -1.377680218341670315, 0.8099999999999982769 ) ) ; +#34298 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34299 = ORIENTED_EDGE ( 'NONE', *, *, #97094, .F. ) ; +#34300 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34301 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53864 ) ) ; +#34302 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.7666666666666657193, 0.000000000000000000 ) ) ; +#34303 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55505 ) ) ; +#34304 = CARTESIAN_POINT ( 'NONE', ( -0.3116609922593340243, -1.321596304865350069, 0.8299999999999999600 ) ) ; +#34305 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311420999999999726, 0.8991599999999999593 ) ) ; +#34306 = FACE_OUTER_BOUND ( 'NONE', #91529, .T. ) ; +#34308 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34307 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.000000000000000000 ) ) ; +#34309 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999996625, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#34310 = CARTESIAN_POINT ( 'NONE', ( 1.799634867437250207, -1.074567238704529970, 0.8100000000000000533 ) ) ; +#34311 = EDGE_CURVE ( 'NONE', #54922, #45275, #69318, .T. ) ; +#34313 = PRESENTATION_STYLE_ASSIGNMENT (( #3137 ) ) ; +#34312 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60400 ) ) ; +#34314 = FILL_AREA_STYLE_COLOUR ( '', #78672 ) ; +#34315 = FILL_AREA_STYLE ('',( #58309 ) ) ; +#34316 = SURFACE_SIDE_STYLE ('',( #26640 ) ) ; +#34317 = ORIENTED_EDGE ( 'NONE', *, *, #6511, .T. ) ; +#34318 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34319 = FILL_AREA_STYLE ('',( #73092 ) ) ; +#34321 = STYLED_ITEM ( 'NONE', ( #88959 ), #44878 ) ; +#34320 = LINE ( 'NONE', #95532, #45229 ) ; +#34322 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6773, 'distance_accuracy_value', 'NONE'); +#34323 = VERTEX_POINT ( 'NONE', #85687 ) ; +#34324 = SURFACE_SIDE_STYLE ('',( #72579 ) ) ; +#34325 = ADVANCED_FACE ( 'NONE', ( #68832 ), #84682, .F. ) ; +#34326 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, -9.880000000000000782, 0.4000000000000000222 ) ) ; +#34327 = EDGE_CURVE ( 'NONE', #67267, #97527, #17738, .T. ) ; +#34328 = FACE_OUTER_BOUND ( 'NONE', #70581, .T. ) ; +#34329 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34330 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34331 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#34332 = PRODUCT ( 'Shield Box_ESP32-S3-MINI-1U_20200714', 'Shield Box_ESP32-S3-MINI-1U_20200714', '', ( #38233 ) ) ; +#34333 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22775 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48340, #47806, #63148 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34334 = AXIS2_PLACEMENT_3D ( 'NONE', #73932, #66275, #97374 ) ; +#34335 = AXIS2_PLACEMENT_3D ( 'NONE', #79639, #18822, #72968 ) ; +#34336 = LINE ( 'NONE', #36323, #22522 ) ; +#34337 = ORIENTED_EDGE ( 'NONE', *, *, #54567, .F. ) ; +#34338 = ORIENTED_EDGE ( 'NONE', *, *, #58223, .T. ) ; +#34339 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34340 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26988, 'distance_accuracy_value', 'NONE'); +#34341 = AXIS2_PLACEMENT_3D ( 'NONE', #41796, #97378, #3983 ) ; +#34342 = LINE ( 'NONE', #33319, #84707 ) ; +#34343 = STYLED_ITEM ( 'NONE', ( #40507 ), #85607 ) ; +#34344 = CARTESIAN_POINT ( 'NONE', ( -0.1914460425574669999, -0.9925253384799729295, 0.8100000000000000533 ) ) ; +#34345 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#34346 = EDGE_CURVE ( 'NONE', #17177, #36855, #32084, .T. ) ; +#34347 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58766 ), #52263 ) ; +#34348 = FILL_AREA_STYLE ('',( #3170 ) ) ; +#34349 = SURFACE_STYLE_USAGE ( .BOTH. , #56829 ) ; +#34350 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#34351 = FILL_AREA_STYLE_COLOUR ( '', #49394 ) ; +#34352 = ORIENTED_EDGE ( 'NONE', *, *, #63863, .T. ) ; +#34353 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#34354 = AXIS2_PLACEMENT_3D ( 'NONE', #43004, #27215, #19522 ) ; +#34355 = FACE_OUTER_BOUND ( 'NONE', #463, .T. ) ; +#34356 = ORIENTED_EDGE ( 'NONE', *, *, #36581, .F. ) ; +#34357 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766239728, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#34358 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34359 = SURFACE_SIDE_STYLE ('',( #43484 ) ) ; +#34360 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34361 = VERTEX_POINT ( 'NONE', #63254 ) ; +#34362 = PRESENTATION_STYLE_ASSIGNMENT (( #48151 ) ) ; +#34363 = EDGE_CURVE ( 'NONE', #41436, #47153, #94336, .T. ) ; +#34364 = SURFACE_SIDE_STYLE ('',( #87949 ) ) ; +#34365 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22969 ) ) ; +#34366 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34367 = SURFACE_STYLE_FILL_AREA ( #3192 ) ; +#34368 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000971, 0.2500000000000000000 ) ) ; +#34369 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31121 ) ) ; +#34370 = ORIENTED_EDGE ( 'NONE', *, *, #18057, .F. ) ; +#34371 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62447 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57496, #18639, #26852 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34372 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000002623, -0.2349999999999999867 ) ) ; +#34373 = ORIENTED_EDGE ( 'NONE', *, *, #16360, .T. ) ; +#34374 = EDGE_LOOP ( 'NONE', ( #12000, #80203, #64859, #97381, #72714, #17532, #60961, #42538 ) ) ; +#34375 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34376 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#34377 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#34378 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67443 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43083, #26288, #58459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34380 = LINE ( 'NONE', #65479, #67933 ) ; +#34379 = FACE_OUTER_BOUND ( 'NONE', #33254, .T. ) ; +#34381 = ORIENTED_EDGE ( 'NONE', *, *, #11270, .F. ) ; +#34383 = ORIENTED_EDGE ( 'NONE', *, *, #88145, .T. ) ; +#34382 = ORIENTED_EDGE ( 'NONE', *, *, #83250, .F. ) ; +#34384 = SURFACE_SIDE_STYLE ('',( #73174 ) ) ; +#34385 = ORIENTED_EDGE ( 'NONE', *, *, #68528, .F. ) ; +#34386 = EDGE_CURVE ( 'NONE', #47416, #38857, #930, .T. ) ; +#34387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87810 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7100, #85290, #40368 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34388 = ORIENTED_EDGE ( 'NONE', *, *, #67242, .T. ) ; +#34389 = ORIENTED_EDGE ( 'NONE', *, *, #79906, .F. ) ; +#34390 = FACE_OUTER_BOUND ( 'NONE', #82559, .T. ) ; +#34391 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#34392 = PRESENTATION_STYLE_ASSIGNMENT (( #88999 ) ) ; +#34393 = PLANE ( 'NONE', #91158 ) ; +#34394 = ORIENTED_EDGE ( 'NONE', *, *, #92687, .T. ) ; +#34395 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#34396 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34397 = ORIENTED_EDGE ( 'NONE', *, *, #22714, .F. ) ; +#34398 = ADVANCED_FACE ( 'NONE', ( #48925 ), #9524, .T. ) ; +#34399 = PRESENTATION_STYLE_ASSIGNMENT (( #43024 ) ) ; +#34400 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662329837, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#34401 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999999237, -0.1499999999999999944 ) ) ; +#34402 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#34403 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6523 ), #13078 ) ; +#34404 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34405 = AXIS2_PLACEMENT_3D ( 'NONE', #74701, #88508, #18545 ) ; +#34406 = FACE_OUTER_BOUND ( 'NONE', #2234, .T. ) ; +#34407 = AXIS2_PLACEMENT_3D ( 'NONE', #2521, #10070, #33678 ) ; +#34409 = PRESENTATION_STYLE_ASSIGNMENT (( #81382 ) ) ; +#34408 = FACE_OUTER_BOUND ( 'NONE', #47763, .T. ) ; +#34410 = FILL_AREA_STYLE_COLOUR ( '', #91433 ) ; +#34411 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34412 = VECTOR ( 'NONE', #48600, 1000.000000000000000 ) ; +#34413 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#34414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29913 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47517, #94469, #86319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34415 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16926 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28250, #90521, #91523 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34416 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34418 = CARTESIAN_POINT ( 'NONE', ( 4.670775750250086844, 8.852158750250087138, 0.8648700000000000276 ) ) ; +#34417 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8648700000000000276 ) ) ; +#34419 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8648700000000000276 ) ) ; +#34420 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#34421 = SURFACE_STYLE_USAGE ( .BOTH. , #3247 ) ; +#34422 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55542 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80083, #56615, #42767 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34423 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57431 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65549, #79902, #25775 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34424 = FACE_OUTER_BOUND ( 'NONE', #27222, .T. ) ; +#34425 = ORIENTED_EDGE ( 'NONE', *, *, #22749, .F. ) ; +#34426 = CARTESIAN_POINT ( 'NONE', ( -1.195496432507400009, -1.512608977738969962, 0.8300000000000024025 ) ) ; +#34427 = EDGE_CURVE ( 'NONE', #28089, #57013, #19935, .T. ) ; +#34428 = PRESENTATION_STYLE_ASSIGNMENT (( #97643 ) ) ; +#34429 = PRESENTATION_STYLE_ASSIGNMENT (( #59816 ) ) ; +#34430 = EDGE_LOOP ( 'NONE', ( #77130, #40762, #2346, #11921 ) ) ; +#34431 = PLANE ( 'NONE', #80743 ) ; +#34432 = VECTOR ( 'NONE', #41575, 1000.000000000000000 ) ; +#34433 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#34434 = FACE_OUTER_BOUND ( 'NONE', #37258, .T. ) ; +#34435 = CARTESIAN_POINT ( 'NONE', ( 1.608267340221630315, -1.417598257925390293, 0.8099999999999976108 ) ) ; +#34436 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20865 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18399, #81240, #32747 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34437 = CARTESIAN_POINT ( 'NONE', ( -0.1796601769484260092, -1.431361989143759894, 0.8299999999999999600 ) ) ; +#34438 = PLANE ( 'NONE', #354 ) ; +#34439 = PLANE ( 'NONE', #21733 ) ; +#34440 = ORIENTED_EDGE ( 'NONE', *, *, #76803, .T. ) ; +#34441 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#34442 = EDGE_CURVE ( 'NONE', #60219, #3831, #1948, .T. ) ; +#34443 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34444 = EDGE_CURVE ( 'NONE', #10790, #58118, #88225, .T. ) ; +#34445 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#34446 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34447 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, 0.000000000000000000 ) ) ; +#34448 = LINE ( 'NONE', #41593, #84396 ) ; +#34449 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34450 = VECTOR ( 'NONE', #47860, 1000.000000000000000 ) ; +#34451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34452 = EDGE_CURVE ( 'NONE', #23174, #40880, #19501, .T. ) ; +#34453 = SURFACE_STYLE_FILL_AREA ( #33947 ) ; +#34454 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34455 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34456 = STYLED_ITEM ( 'NONE', ( #67958 ), #10436 ) ; +#34457 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#34458 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#34459 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.1000000000000016015, 0.000000000000000000 ) ) ; +#34460 = SURFACE_SIDE_STYLE ('',( #88549 ) ) ; +#34461 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#34462 = EDGE_LOOP ( 'NONE', ( #84417, #94234, #36870, #89750 ) ) ; +#34463 = ORIENTED_EDGE ( 'NONE', *, *, #76636, .T. ) ; +#34464 = PLANE ( 'NONE', #79568 ) ; +#34465 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 8.286473000000000866, 0.8991599999999999593 ) ) ; +#34466 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34467 = ADVANCED_FACE ( 'NONE', ( #70885 ), #80572, .T. ) ; +#34468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34469 = FILL_AREA_STYLE_COLOUR ( '', #75354 ) ; +#34470 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34471 = LINE ( 'NONE', #81444, #68382 ) ; +#34472 = VERTEX_POINT ( 'NONE', #27964 ) ; +#34473 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34474 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34475 = ADVANCED_FACE ( 'NONE', ( #12023 ), #59121, .T. ) ; +#34476 = AXIS2_PLACEMENT_3D ( 'NONE', #97581, #52186, #28677 ) ; +#34477 = VERTEX_POINT ( 'NONE', #60977 ) ; +#34478 = SURFACE_SIDE_STYLE ('',( #88565 ) ) ; +#34479 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92193 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89999, #96637, #11305 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34480 = FACE_OUTER_BOUND ( 'NONE', #10950, .T. ) ; +#34481 = EDGE_CURVE ( 'NONE', #36383, #91833, #43912, .T. ) ; +#34482 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35577, #24274, #32419 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34483 = FILL_AREA_STYLE ('',( #73277 ) ) ; +#34484 = ADVANCED_FACE ( 'NONE', ( #26949 ), #19254, .T. ) ; +#34485 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34486 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#34487 = ORIENTED_EDGE ( 'NONE', *, *, #6682, .F. ) ; +#34488 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34489 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47790 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75572, #18923, #93360 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34490 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34491 = VECTOR ( 'NONE', #17662, 1000.000000000000114 ) ; +#34492 = EDGE_CURVE ( 'NONE', #70042, #82464, #30806, .T. ) ; +#34493 = FACE_OUTER_BOUND ( 'NONE', #96469, .T. ) ; +#34494 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71845 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34003, #41150, #11410 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34496 = EDGE_LOOP ( 'NONE', ( #83773, #31709, #49043, #61606, #18862, #62871 ) ) ; +#34497 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#34498 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34499 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#34501 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34500 = CARTESIAN_POINT ( 'NONE', ( -1.194034800317062439, -1.215936827035551948, 0.8099999999998287459 ) ) ; +#34502 = STYLED_ITEM ( 'NONE', ( #6596 ), #66113 ) ; +#34503 = AXIS2_PLACEMENT_3D ( 'NONE', #4143, #42464, #51130 ) ; +#34504 = EDGE_CURVE ( 'NONE', #6655, #53914, #86771, .T. ) ; +#34505 = VECTOR ( 'NONE', #24982, 1000.000000000000000 ) ; +#34506 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65437 ), #76890 ) ; +#34507 = ORIENTED_EDGE ( 'NONE', *, *, #52957, .F. ) ; +#34509 = ORIENTED_EDGE ( 'NONE', *, *, #2442, .F. ) ; +#34508 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34510 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56495, 'distance_accuracy_value', 'NONE'); +#34511 = FACE_OUTER_BOUND ( 'NONE', #68015, .T. ) ; +#34513 = FACE_OUTER_BOUND ( 'NONE', #88712, .T. ) ; +#34512 = SURFACE_STYLE_FILL_AREA ( #11910 ) ; +#34514 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.7000000000000018430, 7.851278178449085673E-79 ) ) ; +#34515 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#34516 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34517 = FACE_OUTER_BOUND ( 'NONE', #13339, .T. ) ; +#34518 = VERTEX_POINT ( 'NONE', #38485 ) ; +#34519 = ADVANCED_FACE ( 'NONE', ( #71136 ), #24200, .F. ) ; +#34520 = PRESENTATION_STYLE_ASSIGNMENT (( #4830 ) ) ; +#34521 = DIRECTION ( 'NONE', ( 0.7071090539100516326, -0.7071045084557385785, 0.000000000000000000 ) ) ; +#34522 = SURFACE_STYLE_USAGE ( .BOTH. , #40150 ) ; +#34523 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, 3.099999999999994316, 0.000000000000000000 ) ) ; +#34524 = ORIENTED_EDGE ( 'NONE', *, *, #41468, .T. ) ; +#34525 = ADVANCED_FACE ( 'NONE', ( #100627 ), #94596, .T. ) ; +#34526 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34527 = ORIENTED_EDGE ( 'NONE', *, *, #851, .F. ) ; +#34528 = ORIENTED_EDGE ( 'NONE', *, *, #74980, .F. ) ; +#34529 = CARTESIAN_POINT ( 'NONE', ( 1.112256145284957309, -1.203341844243224878, 0.8099999999998620526 ) ) ; +#34530 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95842, #57099, #2952, #79556 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#34532 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.000000000000000000 ) ) ; +#34531 = SURFACE_SIDE_STYLE ('',( #56511 ) ) ; +#34533 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34534 = ADVANCED_FACE ( 'NONE', ( #54831 ), #85947, .T. ) ; +#34535 = ORIENTED_EDGE ( 'NONE', *, *, #40639, .T. ) ; +#34536 = LINE ( 'NONE', #97738, #30423 ) ; +#34537 = ORIENTED_EDGE ( 'NONE', *, *, #73562, .T. ) ; +#34538 = CARTESIAN_POINT ( 'NONE', ( 1.303582274605669999, -1.428972370004099934, 0.8299999999999999600 ) ) ; +#34539 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34540 = ORIENTED_EDGE ( 'NONE', *, *, #68766, .T. ) ; +#34541 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34542 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34543 = CARTESIAN_POINT ( 'NONE', ( -1.005723260889149984, -1.285676881280640282, 0.8100000000000000533 ) ) ; +#34544 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#34545 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24784 ) ) ; +#34546 = VECTOR ( 'NONE', #40255, 1000.000000000000000 ) ; +#34547 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#34548 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34549 = CARTESIAN_POINT ( 'NONE', ( -0.08340097402597421161, 0.7099999999999999645, 0.2077922077922079724 ) ) ; +#34551 = EDGE_CURVE ( 'NONE', #43302, #19914, #88473, .T. ) ; +#34550 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34552 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34553 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75270 ) ) ; +#34554 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8100000000000000533 ) ) ; +#34555 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65485 ) ) ; +#34556 = ORIENTED_EDGE ( 'NONE', *, *, #14850, .T. ) ; +#34557 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000010436, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#34558 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34560 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990585, 0.000000000000000000 ) ) ; +#34559 = SURFACE_STYLE_FILL_AREA ( #64169 ) ; +#34561 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8648700000000000276 ) ) ; +#34562 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81711, 'distance_accuracy_value', 'NONE'); +#34563 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24799 ), #36218 ) ; +#34564 = SURFACE_STYLE_USAGE ( .BOTH. , #81019 ) ; +#34565 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34566 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34567 = EDGE_LOOP ( 'NONE', ( #65950, #20953, #15606, #38609 ) ) ; +#34568 = STYLED_ITEM ( 'NONE', ( #32860 ), #7526 ) ; +#34569 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34570 = ADVANCED_FACE ( 'NONE', ( #18510 ), #73168, .T. ) ; +#34571 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34572 = PLANE ( 'NONE', #51757 ) ; +#34573 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#34574 = VECTOR ( 'NONE', #93404, 1000.000000000000000 ) ; +#34575 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34576 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#34577 = SURFACE_STYLE_USAGE ( .BOTH. , #66193 ) ; +#34578 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34579 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974019543, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#34580 = LINE ( 'NONE', #65697, #3001 ) ; +#34581 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#34582 = VECTOR ( 'NONE', #12306, 1000.000000000000000 ) ; +#34583 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#34584 = FILL_AREA_STYLE ('',( #73372 ) ) ; +#34585 = CARTESIAN_POINT ( 'NONE', ( 2.818155999999999661, 5.528756999999999699, 0.8648700000000000276 ) ) ; +#34586 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#34587 = FILL_AREA_STYLE ('',( #9105 ) ) ; +#34588 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#34589 = VERTEX_POINT ( 'NONE', #65477 ) ; +#34590 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34591 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34592 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34594 = CARTESIAN_POINT ( 'NONE', ( 7.944680750250086909, 10.08959524974991240, 0.8648700000000000276 ) ) ; +#34593 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34595 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.05000000000000000971, 0.1900000000000000022 ) ) ; +#34596 = VECTOR ( 'NONE', #99552, 1000.000000000000000 ) ; +#34597 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#34598 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#34599 = VERTEX_POINT ( 'NONE', #1719 ) ; +#34601 = EDGE_CURVE ( 'NONE', #76626, #22697, #72645, .T. ) ; +#34600 = CARTESIAN_POINT ( 'NONE', ( 9.818513124875011044, 9.135001124875012479, 0.8991599999999999593 ) ) ; +#34602 = VECTOR ( 'NONE', #13927, 1000.000000000000000 ) ; +#34603 = FACE_OUTER_BOUND ( 'NONE', #17019, .T. ) ; +#34604 = FILL_AREA_STYLE ('',( #57091 ) ) ; +#34605 = VERTEX_POINT ( 'NONE', #57884 ) ; +#34606 = VERTEX_POINT ( 'NONE', #33870 ) ; +#34607 = AXIS2_PLACEMENT_3D ( 'NONE', #42203, #90140, #52374 ) ; +#34608 = VECTOR ( 'NONE', #31825, 1000.000000000000000 ) ; +#34609 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.4245906043549200204, -0.01999999999999999695 ) ) ; +#34610 = LINE ( 'NONE', #18218, #16424 ) ; +#34611 = ORIENTED_EDGE ( 'NONE', *, *, #43241, .F. ) ; +#34612 = CARTESIAN_POINT ( 'NONE', ( 1.788063499344580087, -1.247965265924660061, 0.8100000000000000533 ) ) ; +#34613 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34614 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34615 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34616 = VECTOR ( 'NONE', #87174, 1000.000000000000000 ) ; +#34617 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #29942, #87472 ) ; +#34618 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8099999999998663824 ) ) ; +#34621 = ORIENTED_EDGE ( 'NONE', *, *, #37639, .T. ) ; +#34620 = VERTEX_POINT ( 'NONE', #19007 ) ; +#34619 = EDGE_CURVE ( 'NONE', #85180, #17507, #96101, .T. ) ; +#34622 = EDGE_LOOP ( 'NONE', ( #39347, #15968, #33369, #56727 ) ) ; +#34623 = VECTOR ( 'NONE', #46939, 1000.000000000000000 ) ; +#34624 = ORIENTED_EDGE ( 'NONE', *, *, #98034, .T. ) ; +#34625 = LINE ( 'NONE', #33095, #9907 ) ; +#34626 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86536, 'distance_accuracy_value', 'NONE'); +#34627 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93221 ) ) ; +#34628 = LINE ( 'NONE', #42276, #91457 ) ; +#34629 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34630 = ORIENTED_EDGE ( 'NONE', *, *, #12138, .T. ) ; +#34631 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34632 = LINE ( 'NONE', #43261, #18870 ) ; +#34633 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.600000000000000089, -0.1499999999999999944 ) ) ; +#34634 = VERTEX_POINT ( 'NONE', #60014 ) ; +#34635 = FACE_OUTER_BOUND ( 'NONE', #47661, .T. ) ; +#34636 = VECTOR ( 'NONE', #65717, 1000.000000000000000 ) ; +#34637 = VERTEX_POINT ( 'NONE', #41075 ) ; +#34638 = FILL_AREA_STYLE ('',( #3482 ) ) ; +#34639 = ORIENTED_EDGE ( 'NONE', *, *, #58451, .T. ) ; +#34640 = ORIENTED_EDGE ( 'NONE', *, *, #77180, .F. ) ; +#34641 = SURFACE_STYLE_USAGE ( .BOTH. , #50479 ) ; +#34642 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8422 ), #75876 ) ; +#34643 = FILL_AREA_STYLE ('',( #43274 ) ) ; +#34645 = EDGE_CURVE ( 'NONE', #31422, #78858, #9821, .T. ) ; +#34644 = FILL_AREA_STYLE_COLOUR ( '', #100917 ) ; +#34647 = VERTEX_POINT ( 'NONE', #2265 ) ; +#34646 = SURFACE_STYLE_FILL_AREA ( #11550 ) ; +#34648 = SURFACE_STYLE_USAGE ( .BOTH. , #81113 ) ; +#34649 = ORIENTED_EDGE ( 'NONE', *, *, #12067, .F. ) ; +#34650 = SURFACE_SIDE_STYLE ('',( #43781 ) ) ; +#34651 = EDGE_LOOP ( 'NONE', ( #80856, #58213, #53240, #37249 ) ) ; +#34653 = PRESENTATION_STYLE_ASSIGNMENT (( #12064 ) ) ; +#34652 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34654 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4600000000000000200, 0.2349999999999999867 ) ) ; +#34655 = ORIENTED_EDGE ( 'NONE', *, *, #61728, .F. ) ; +#34656 = EDGE_CURVE ( 'NONE', #100744, #47396, #8303, .T. ) ; +#34657 = EDGE_LOOP ( 'NONE', ( #91477, #96468, #37860, #58035 ) ) ; +#34659 = FACE_OUTER_BOUND ( 'NONE', #47645, .T. ) ; +#34658 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8299999999999999600 ) ) ; +#34660 = SURFACE_STYLE_USAGE ( .BOTH. , #50495 ) ; +#34661 = SURFACE_SIDE_STYLE ('',( #73455 ) ) ; +#34662 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33032 ) ) ; +#34663 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50917 ), #63943 ) ; +#34664 = SURFACE_SIDE_STYLE ('',( #73457 ) ) ; +#34665 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#34667 = STYLED_ITEM ( 'NONE', ( #75549 ), #46946 ) ; +#34666 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000000001155, 0.000000000000000000 ) ) ; +#34668 = EDGE_CURVE ( 'NONE', #13908, #71148, #24248, .T. ) ; +#34669 = EDGE_CURVE ( 'NONE', #80892, #40675, #31879, .T. ) ; +#34670 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#34671 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90026, 'distance_accuracy_value', 'NONE'); +#34672 = EDGE_LOOP ( 'NONE', ( #50121, #76117, #11775, #37720 ) ) ; +#34673 = PLANE ( 'NONE', #90362 ) ; +#34674 = ORIENTED_EDGE ( 'NONE', *, *, #19642, .F. ) ; +#34675 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34676 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34677 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34678 = EDGE_CURVE ( 'NONE', #60744, #27329, #79871, .T. ) ; +#34679 = EDGE_CURVE ( 'NONE', #39926, #69995, #55397, .T. ) ; +#34680 = CARTESIAN_POINT ( 'NONE', ( 1.406489741257900050, -1.236164603532529993, 0.8299999999999999600 ) ) ; +#34681 = LINE ( 'NONE', #72953, #18654 ) ; +#34682 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26506 ) ) ; +#34683 = VECTOR ( 'NONE', #29267, 1000.000000000000000 ) ; +#34684 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#34685 = SURFACE_SIDE_STYLE ('',( #11078 ) ) ; +#34686 = ORIENTED_EDGE ( 'NONE', *, *, #28988, .T. ) ; +#34687 = SURFACE_STYLE_USAGE ( .BOTH. , #57684 ) ; +#34688 = FACE_OUTER_BOUND ( 'NONE', #28810, .T. ) ; +#34689 = EDGE_CURVE ( 'NONE', #80014, #52187, #86511, .T. ) ; +#34690 = VECTOR ( 'NONE', #7238, 1000.000000000000000 ) ; +#34691 = CARTESIAN_POINT ( 'NONE', ( 0.2967604117379429862, -0.9084949572282049468, 0.8100000000000000533 ) ) ; +#34692 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#34693 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34694 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34695 = AXIS2_PLACEMENT_3D ( 'NONE', #88380, #3113, #41432 ) ; +#34696 = STYLED_ITEM ( 'NONE', ( #15396 ), #87261 ) ; +#34697 = EDGE_CURVE ( 'NONE', #46032, #75798, #87022, .T. ) ; +#34698 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34699 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.000000000000000000, 1.149999999999999911 ) ) ; +#34700 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#34701 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42419, #13189, #74564 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34702 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000000971, 0.2400000000000000189 ) ) ; +#34703 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8547 ), #64056 ) ; +#34704 = FACE_OUTER_BOUND ( 'NONE', #60883, .T. ) ; +#34705 = STYLED_ITEM ( 'NONE', ( #60504 ), #11218 ) ; +#34706 = VERTEX_POINT ( 'NONE', #78844 ) ; +#34707 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#34708 = FILL_AREA_STYLE ('',( #97910 ) ) ; +#34709 = VECTOR ( 'NONE', #21827, 1000.000000000000000 ) ; +#34710 = VERTEX_POINT ( 'NONE', #79357 ) ; +#34711 = PLANE ( 'NONE', #99881 ) ; +#34712 = PLANE ( 'NONE', #48630 ) ; +#34713 = SURFACE_STYLE_USAGE ( .BOTH. , #17835 ) ; +#34714 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #358, #31015, #87162, #62194 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#34715 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31393 ) ) ; +#34716 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#34717 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27, #40376, #1571, #32715 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#34718 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34719 = ORIENTED_EDGE ( 'NONE', *, *, #21536, .T. ) ; +#34720 = VERTEX_POINT ( 'NONE', #64540 ) ; +#34721 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 9.350000000000001421, 0.03429000000000000103 ) ) ; +#34722 = EDGE_CURVE ( 'NONE', #97804, #82331, #29264, .T. ) ; +#34723 = AXIS2_PLACEMENT_3D ( 'NONE', #11667, #42911, #74057 ) ; +#34724 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11615, 'distance_accuracy_value', 'NONE'); +#34725 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#34726 = LINE ( 'NONE', #89329, #17246 ) ; +#34727 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34728 = CARTESIAN_POINT ( 'NONE', ( -1.347418568134061578, -0.9557253670106938825, 0.8100000000000207034 ) ) ; +#34729 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95010 ), #77100 ) ; +#34730 = EDGE_CURVE ( 'NONE', #18587, #90736, #4831, .T. ) ; +#34731 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34732 = SURFACE_STYLE_FILL_AREA ( #19884 ) ; +#34733 = VERTEX_POINT ( 'NONE', #8807 ) ; +#34734 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55939 ) ) ; +#34735 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#34736 = VERTEX_POINT ( 'NONE', #40570 ) ; +#34737 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34738 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34739 = LINE ( 'NONE', #64347, #71362 ) ; +#34740 = PRESENTATION_STYLE_ASSIGNMENT (( #3577 ) ) ; +#34741 = CARTESIAN_POINT ( 'NONE', ( -1.031006683134279900, -1.010360997253880067, 0.8100000000000000533 ) ) ; +#34742 = FILL_AREA_STYLE_COLOUR ( '', #73084 ) ; +#34743 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#34744 = SURFACE_STYLE_USAGE ( .BOTH. , #80702 ) ; +#34747 = EDGE_LOOP ( 'NONE', ( #19466, #14935, #82462, #49777 ) ) ; +#34746 = ORIENTED_EDGE ( 'NONE', *, *, #21345, .T. ) ; +#34745 = ADVANCED_FACE ( 'NONE', ( #40051 ), #33413, .T. ) ; +#34748 = SURFACE_STYLE_FILL_AREA ( #19900 ) ; +#34749 = ORIENTED_EDGE ( 'NONE', *, *, #90802, .F. ) ; +#34750 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#34751 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34753 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#34752 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.700000000000000178, 1.495481557822595733E-79 ) ) ; +#34754 = ORIENTED_EDGE ( 'NONE', *, *, #57734, .F. ) ; +#34755 = VECTOR ( 'NONE', #98650, 1000.000000000000000 ) ; +#34757 = EDGE_CURVE ( 'NONE', #46887, #89137, #60770, .T. ) ; +#34756 = ORIENTED_EDGE ( 'NONE', *, *, #79900, .T. ) ; +#34758 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34759 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#34760 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34761 = STYLED_ITEM ( 'NONE', ( #94404 ), #35107 ) ; +#34762 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.4999999999999990563, 0.1829999999999789850 ) ) ; +#34763 = SURFACE_STYLE_FILL_AREA ( #80717 ) ; +#34764 = SURFACE_STYLE_USAGE ( .BOTH. , #42408 ) ; +#34765 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34766 = ORIENTED_EDGE ( 'NONE', *, *, #98066, .T. ) ; +#34767 = ORIENTED_EDGE ( 'NONE', *, *, #7493, .T. ) ; +#34768 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90187 ) ) ; +#34769 = EDGE_LOOP ( 'NONE', ( #46361, #10902, #9982, #87236 ) ) ; +#34770 = SURFACE_STYLE_FILL_AREA ( #58265 ) ; +#34771 = VECTOR ( 'NONE', #24040, 1000.000000000000000 ) ; +#34772 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62448 ) ) ; +#34773 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93442 ), #25007 ) ; +#34775 = ORIENTED_EDGE ( 'NONE', *, *, #60923, .T. ) ; +#34774 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#34776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73892 ) ) ; +#34777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57599 ), #18400 ) ; +#34778 = FILL_AREA_STYLE ('',( #10666 ) ) ; +#34779 = FACE_OUTER_BOUND ( 'NONE', #95431, .T. ) ; +#34780 = ORIENTED_EDGE ( 'NONE', *, *, #94604, .F. ) ; +#34781 = FACE_OUTER_BOUND ( 'NONE', #77817, .T. ) ; +#34782 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34783 = ORIENTED_EDGE ( 'NONE', *, *, #43229, .T. ) ; +#34784 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34785 = ORIENTED_EDGE ( 'NONE', *, *, #84263, .F. ) ; +#34786 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34787 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34788 = VECTOR ( 'NONE', #97799, 1000.000000000000000 ) ; +#34789 = CARTESIAN_POINT ( 'NONE', ( -1.336283849596160200, -1.153389236204189983, 0.8300000000000000711 ) ) ; +#34790 = CARTESIAN_POINT ( 'NONE', ( -0.5999999999999999778, 2.833381677428764840E-18, 0.6500000000000001332 ) ) ; +#34791 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#34793 = CARTESIAN_POINT ( 'NONE', ( 1.654345427547579961, -0.9032194100038879458, 0.8299999999999997380 ) ) ; +#34794 = VERTEX_POINT ( 'NONE', #10312 ) ; +#34795 = PLANE ( 'NONE', #81644 ) ; +#34796 = PRESENTATION_STYLE_ASSIGNMENT (( #81761 ) ) ; +#34797 = VERTEX_POINT ( 'NONE', #41569 ) ; +#34798 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80410 ) ) ; +#34799 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.000000000000000000 ) ) ; +#34800 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#34801 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#34802 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95080 ) ) ; +#34804 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#34803 = CARTESIAN_POINT ( 'NONE', ( 0.01523096807867625052, -1.349674827204884409, 0.8099999999997233857 ) ) ; +#34805 = LINE ( 'NONE', #2632, #100732 ) ; +#34806 = CARTESIAN_POINT ( 'NONE', ( 1.790988317735370039, -1.106837409965790053, 0.8100000000000000533 ) ) ; +#34807 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#34808 = EDGE_CURVE ( 'NONE', #32195, #67337, #88523, .T. ) ; +#34809 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#34810 = LINE ( 'NONE', #40954, #86640 ) ; +#34811 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#34812 = PRESENTATION_STYLE_ASSIGNMENT (( #50143 ) ) ; +#34813 = ADVANCED_FACE ( 'NONE', ( #29135 ), #10829, .T. ) ; +#34814 = EDGE_LOOP ( 'NONE', ( #79504, #37344, #75918, #62376 ) ) ; +#34815 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#34816 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34817 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#34818 = STYLED_ITEM ( 'NONE', ( #28268 ), #19622 ) ; +#34820 = ORIENTED_EDGE ( 'NONE', *, *, #24478, .T. ) ; +#34819 = AXIS2_PLACEMENT_3D ( 'NONE', #11466, #89678, #73858 ) ; +#34821 = PRESENTATION_STYLE_ASSIGNMENT (( #26149 ) ) ; +#34822 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34823 = FILL_AREA_STYLE_COLOUR ( '', #29447 ) ; +#34824 = CARTESIAN_POINT ( 'NONE', ( 2.216666666666666785, 3.099999999999969891, 0.000000000000000000 ) ) ; +#34825 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#34826 = SURFACE_SIDE_STYLE ('',( #33811 ) ) ; +#34827 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95110 ), #38087 ) ; +#34828 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #748, #62567, #47214 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34829 = FACE_OUTER_BOUND ( 'NONE', #37856, .T. ) ; +#34830 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34831 = LINE ( 'NONE', #11722, #75219 ) ; +#34832 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34834 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#34833 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5451 ) ) ; +#34835 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34836 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65459, 'distance_accuracy_value', 'NONE'); +#34837 = AXIS2_PLACEMENT_3D ( 'NONE', #86300, #54160, #45946 ) ; +#34838 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34839 = VERTEX_POINT ( 'NONE', #3256 ) ; +#34841 = ORIENTED_EDGE ( 'NONE', *, *, #10909, .T. ) ; +#34840 = VECTOR ( 'NONE', #9300, 1000.000000000000000 ) ; +#34842 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#34843 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50896, 'distance_accuracy_value', 'NONE'); +#34844 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29100, 'distance_accuracy_value', 'NONE'); +#34845 = STYLED_ITEM ( 'NONE', ( #26150 ), #9664 ) ; +#34846 = SURFACE_SIDE_STYLE ('',( #55798 ) ) ; +#34847 = CARTESIAN_POINT ( 'NONE', ( -0.2157361669573319984, -1.030915998478540097, 0.8299999999999999600 ) ) ; +#34848 = FACE_OUTER_BOUND ( 'NONE', #38875, .T. ) ; +#34849 = PRESENTATION_STYLE_ASSIGNMENT (( #96064 ) ) ; +#34850 = LINE ( 'NONE', #49657, #96615 ) ; +#34851 = LINE ( 'NONE', #58346, #54935 ) ; +#34852 = SURFACE_SIDE_STYLE ('',( #5139 ) ) ; +#34853 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34854 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#34855 = EDGE_CURVE ( 'NONE', #66265, #12703, #37310, .T. ) ; +#34856 = EDGE_LOOP ( 'NONE', ( #78173, #70986, #73600, #24576 ) ) ; +#34857 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#34858 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34859 = EDGE_LOOP ( 'NONE', ( #55522, #89732, #45556, #100088 ) ) ; +#34860 = ORIENTED_EDGE ( 'NONE', *, *, #619, .T. ) ; +#34861 = PRESENTATION_STYLE_ASSIGNMENT (( #57860 ) ) ; +#34862 = PRESENTATION_STYLE_ASSIGNMENT (( #81334 ) ) ; +#34863 = DIRECTION ( 'NONE', ( 0.7071067811865469066, 0.7071067811865482389, 0.000000000000000000 ) ) ; +#34865 = ORIENTED_EDGE ( 'NONE', *, *, #22053, .T. ) ; +#34864 = STYLED_ITEM ( 'NONE', ( #70784 ), #70976 ) ; +#34866 = PRESENTATION_STYLE_ASSIGNMENT (( #42996 ) ) ; +#34867 = VERTEX_POINT ( 'NONE', #20964 ) ; +#34868 = FILL_AREA_STYLE ('',( #48674 ) ) ; +#34869 = FACE_OUTER_BOUND ( 'NONE', #7725, .T. ) ; +#34870 = EDGE_LOOP ( 'NONE', ( #48730, #32347, #42536 ) ) ; +#34871 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #80567, #41753, #1440, #31563, #70878, #923, #32077, #56075, #87204, #36119, #18740, #96338, #12529, #65745, #83066, #97338, #59112 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.459602605566460308E-05, 2.829147775930741747E-05, 4.142470754413806068E-05, 5.418611556289563042E-05, 6.668131546734849986E-05, 7.901020621885268080E-05, 9.138505479862083446E-05, 0.0001038678583755627813, 0.0001164459743690362615, 0.0001292627216649090346, 0.0001423239016427833294, 0.0001557007412053608311, 0.0001825303674053052106, 0.0002092578554027745388 ), + .UNSPECIFIED. ) ; +#34872 = ORIENTED_EDGE ( 'NONE', *, *, #43970, .T. ) ; +#34873 = PLANE ( 'NONE', #17090 ) ; +#34874 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34875 = FACE_OUTER_BOUND ( 'NONE', #57654, .T. ) ; +#34877 = FACE_OUTER_BOUND ( 'NONE', #22048, .T. ) ; +#34876 = CARTESIAN_POINT ( 'NONE', ( 0.3142305969234919782, -0.9692640729113169984, 0.8299999999999999600 ) ) ; +#34878 = EDGE_LOOP ( 'NONE', ( #100127, #66694, #59638, #80423 ) ) ; +#34880 = VERTEX_POINT ( 'NONE', #33920 ) ; +#34879 = EDGE_LOOP ( 'NONE', ( #28911, #75093, #97812, #66995 ) ) ; +#34882 = EDGE_CURVE ( 'NONE', #12657, #32075, #6049, .T. ) ; +#34881 = VECTOR ( 'NONE', #15941, 1000.000000000000114 ) ; +#34883 = VECTOR ( 'NONE', #69974, 1000.000000000000000 ) ; +#34884 = ORIENTED_EDGE ( 'NONE', *, *, #51251, .T. ) ; +#34885 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#34886 = VERTEX_POINT ( 'NONE', #26257 ) ; +#34887 = ORIENTED_EDGE ( 'NONE', *, *, #100308, .F. ) ; +#34888 = FILL_AREA_STYLE ('',( #98557 ) ) ; +#34889 = SURFACE_STYLE_FILL_AREA ( #64507 ) ; +#34890 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34891 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34892 = ORIENTED_EDGE ( 'NONE', *, *, #87671, .F. ) ; +#34893 = CARTESIAN_POINT ( 'NONE', ( 4.670776249750026032, 3.676137249750024871, 0.8648700000000000276 ) ) ; +#34894 = SURFACE_SIDE_STYLE ('',( #42541 ) ) ; +#34895 = ORIENTED_EDGE ( 'NONE', *, *, #42813, .T. ) ; +#34896 = ADVANCED_FACE ( 'NONE', ( #36793 ), #56908, .F. ) ; +#34897 = SURFACE_STYLE_FILL_AREA ( #58396 ) ; +#34898 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#34899 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85364 ), #70723 ) ; +#34900 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34901 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#34902 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#34903 = PRESENTATION_STYLE_ASSIGNMENT (( #26233 ) ) ; +#34904 = AXIS2_PLACEMENT_3D ( 'NONE', #99218, #23220, #13457 ) ; +#34905 = LINE ( 'NONE', #97134, #3620 ) ; +#34906 = VECTOR ( 'NONE', #63859, 1000.000000000000000 ) ; +#34907 = CARTESIAN_POINT ( 'NONE', ( 1.793081130502420129, -1.407725713391660083, 0.8299999999999999600 ) ) ; +#34908 = LINE ( 'NONE', #48715, #38589 ) ; +#34909 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000089, 2.523820061220085176, -0.02000000000000000042 ) ) ; +#34910 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18040, #42580, #34933, #3764, #3264, #97650, #74219, #57409, #34435, #11332, #41080, #65053, #49753, #27270, #49236, #35446, #4266, #80896, #96159 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.499429272456228083E-05, 2.910519492223530112E-05, 4.243594228491879633E-05, 5.526245320821700176E-05, 6.774248316511283458E-05, 7.971218850131226829E-05, 9.167755485405163038E-05, 0.0001038219916922433463, 0.0001159584851984034716, 0.0001281218428945049277, 0.0001403247781111681023, 0.0001527207142941646844, 0.0001654374484543479247, 0.0001786491364629505215, 0.0001923091419584448819, 0.0002064641342719148289 ), + .UNSPECIFIED. ) ; +#34911 = SURFACE_STYLE_FILL_AREA ( #3741 ) ; +#34912 = EDGE_CURVE ( 'NONE', #66870, #77948, #62440, .T. ) ; +#34913 = AXIS2_PLACEMENT_3D ( 'NONE', #22182, #84467, #6770 ) ; +#34914 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34916 = SURFACE_STYLE_FILL_AREA ( #82373 ) ; +#34915 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#34917 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#34918 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.7000000000000021760, 0.1829999999999659677 ) ) ; +#34919 = PLANE ( 'NONE', #80673 ) ; +#34920 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56316 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48548, #17864, #79169 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34921 = FILL_AREA_STYLE_COLOUR ( '', #1943 ) ; +#34922 = CARTESIAN_POINT ( 'NONE', ( 1.137126380867480080, -0.8900438058027670962, 0.8100000000000000533 ) ) ; +#34923 = ORIENTED_EDGE ( 'NONE', *, *, #49937, .T. ) ; +#34924 = VECTOR ( 'NONE', #34013, 1000.000000000000000 ) ; +#34925 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#34926 = SURFACE_STYLE_FILL_AREA ( #49227 ) ; +#34927 = EDGE_CURVE ( 'NONE', #72485, #8907, #7555, .T. ) ; +#34928 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#34929 = ORIENTED_EDGE ( 'NONE', *, *, #43398, .F. ) ; +#34930 = PRESENTATION_STYLE_ASSIGNMENT (( #50266 ) ) ; +#34931 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#34932 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#34933 = CARTESIAN_POINT ( 'NONE', ( 1.678890544094120196, -1.445107798742940153, 0.8099999999999976108 ) ) ; +#34934 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#34935 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34936 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34937 = SURFACE_STYLE_USAGE ( .BOTH. , #38318 ) ; +#34938 = ORIENTED_EDGE ( 'NONE', *, *, #51349, .F. ) ; +#34939 = PLANE ( 'NONE', #83256 ) ; +#34940 = FACE_OUTER_BOUND ( 'NONE', #50547, .T. ) ; +#34941 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000411 ) ) ; +#34942 = CARTESIAN_POINT ( 'NONE', ( 1.098582290651209936, -0.9005718509792439708, 0.8299999999999994049 ) ) ; +#34943 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51308 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44419, #84259, #14252 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34944 = SURFACE_SIDE_STYLE ('',( #3779 ) ) ; +#34945 = FACE_OUTER_BOUND ( 'NONE', #73647, .T. ) ; +#34946 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8648700000000000276 ) ) ; +#34947 = AXIS2_PLACEMENT_3D ( 'NONE', #9612, #56189, #73000 ) ; +#34948 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#34949 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#34950 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85254, 'distance_accuracy_value', 'NONE'); +#34951 = FILL_AREA_STYLE ('',( #57955 ) ) ; +#34952 = EDGE_CURVE ( 'NONE', #538, #53502, #69915, .T. ) ; +#34953 = PRESENTATION_STYLE_ASSIGNMENT (( #59956 ) ) ; +#34954 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34955 = ORIENTED_EDGE ( 'NONE', *, *, #16292, .T. ) ; +#34956 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#34957 = ORIENTED_EDGE ( 'NONE', *, *, #33160, .F. ) ; +#34958 = FACE_OUTER_BOUND ( 'NONE', #1702, .T. ) ; +#34959 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24877, 'distance_accuracy_value', 'NONE'); +#34960 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16933, 'distance_accuracy_value', 'NONE'); +#34961 = FILL_AREA_STYLE_COLOUR ( '', #50434 ) ; +#34962 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2784314575050761964, -0.1458578643762690474 ) ) ; +#34963 = SURFACE_SIDE_STYLE ('',( #82424 ) ) ; +#34964 = CARTESIAN_POINT ( 'NONE', ( 9.076051499499822484, 8.958224500500174159, 0.8991599999999999593 ) ) ; +#34965 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1775 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6569, #90907, #92855 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34966 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.123820061220065281, 0.000000000000000000 ) ) ; +#34967 = STYLED_ITEM ( 'NONE', ( #890 ), #19956 ) ; +#34968 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#34969 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#34970 = STYLED_ITEM ( 'NONE', ( #98995 ), #22035 ) ; +#34971 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34972 = EDGE_CURVE ( 'NONE', #75772, #14054, #47459, .T. ) ; +#34973 = ORIENTED_EDGE ( 'NONE', *, *, #95944, .F. ) ; +#34974 = SURFACE_STYLE_FILL_AREA ( #95183 ) ; +#34975 = CARTESIAN_POINT ( 'NONE', ( 1.152377709317067289, -1.440493760292191450, 0.8099999999997128386 ) ) ; +#34976 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#34977 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35042, 'distance_accuracy_value', 'NONE'); +#34978 = AXIS2_PLACEMENT_3D ( 'NONE', #68721, #85573, #14585 ) ; +#34979 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#34980 = VERTEX_POINT ( 'NONE', #93376 ) ; +#34981 = STYLED_ITEM ( 'NONE', ( #91520 ), #61496 ) ; +#34982 = FILL_AREA_STYLE_COLOUR ( '', #53303 ) ; +#34983 = STYLED_ITEM ( 'NONE', ( #57864 ), #97434 ) ; +#34984 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#34985 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7685, #15407, #104 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34986 = FACE_OUTER_BOUND ( 'NONE', #81475, .T. ) ; +#34987 = SURFACE_STYLE_FILL_AREA ( #73764 ) ; +#34988 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#34989 = EDGE_LOOP ( 'NONE', ( #96577, #28679, #100372, #29525 ) ) ; +#34990 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#34991 = VECTOR ( 'NONE', #50079, 1000.000000000000000 ) ; +#34992 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#34993 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29507, 'distance_accuracy_value', 'NONE'); +#34994 = FILL_AREA_STYLE ('',( #57470 ) ) ; +#34995 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63030, #24747, #24230 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#34996 = LINE ( 'NONE', #20634, #9913 ) ; +#34997 = CARTESIAN_POINT ( 'NONE', ( 1.655510330387720108, -0.9679977428869779299, 0.8099999999999994982 ) ) ; +#34998 = ORIENTED_EDGE ( 'NONE', *, *, #85164, .T. ) ; +#34999 = CARTESIAN_POINT ( 'NONE', ( 2.216666666666666785, -3.099999999999969891, 0.000000000000000000 ) ) ; +#35000 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#35001 = CARTESIAN_POINT ( 'NONE', ( -0.5594783971358769925, -0.9704561130045840089, 0.8299999999999999600 ) ) ; +#35002 = FACE_OUTER_BOUND ( 'NONE', #49965, .T. ) ; +#35003 = FACE_OUTER_BOUND ( 'NONE', #56944, .T. ) ; +#35004 = FILL_AREA_STYLE_COLOUR ( '', #4338 ) ; +#35005 = ORIENTED_EDGE ( 'NONE', *, *, #66435, .T. ) ; +#35006 = VECTOR ( 'NONE', #67125, 1000.000000000000000 ) ; +#35007 = ADVANCED_FACE ( 'NONE', ( #69841 ), #53621, .T. ) ; +#35008 = EDGE_CURVE ( 'NONE', #19379, #95352, #30594, .T. ) ; +#35009 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21868 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21327, #60654, #91752 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35010 = ORIENTED_EDGE ( 'NONE', *, *, #21130, .F. ) ; +#35012 = ORIENTED_EDGE ( 'NONE', *, *, #55055, .T. ) ; +#35011 = SURFACE_SIDE_STYLE ('',( #79445 ) ) ; +#35013 = AXIS2_PLACEMENT_3D ( 'NONE', #38323, #54663, #46440 ) ; +#35014 = SURFACE_SIDE_STYLE ('',( #96732 ) ) ; +#35015 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155850987, 0.8100000000000292522 ) ) ; +#35016 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#35017 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999989875, 0.000000000000000000 ) ) ; +#35018 = VERTEX_POINT ( 'NONE', #84746 ) ; +#35019 = EDGE_CURVE ( 'NONE', #62079, #88578, #46941, .T. ) ; +#35020 = CARTESIAN_POINT ( 'NONE', ( 1.381066160531370102, -1.463531211619029992, 0.8299999999999999600 ) ) ; +#35021 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#35022 = EDGE_CURVE ( 'NONE', #17448, #74432, #78106, .T. ) ; +#35023 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#35024 = AXIS2_PLACEMENT_3D ( 'NONE', #4208, #89485, #51195 ) ; +#35025 = PRESENTATION_STYLE_ASSIGNMENT (( #82969 ) ) ; +#35026 = ORIENTED_EDGE ( 'NONE', *, *, #44433, .F. ) ; +#35027 = DIRECTION ( 'NONE', ( -0.9361199317767866512, 0.000000000000000000, -0.3516809254569038812 ) ) ; +#35028 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13791 ), #53011 ) ; +#35029 = VERTEX_POINT ( 'NONE', #39807 ) ; +#35031 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#35030 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#35032 = CARTESIAN_POINT ( 'NONE', ( 10.82260475024997604, 4.397386249750026010, 0.8991599999999999593 ) ) ; +#35033 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57863 ), #70862 ) ; +#35034 = ORIENTED_EDGE ( 'NONE', *, *, #36211, .T. ) ; +#35035 = EDGE_CURVE ( 'NONE', #61753, #25960, #99474, .T. ) ; +#35036 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7139 ) ) ; +#35037 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31619 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23762, #46185, #53385 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35038 = ORIENTED_EDGE ( 'NONE', *, *, #33779, .F. ) ; +#35039 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#35040 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35041 = EDGE_LOOP ( 'NONE', ( #77811, #56711, #1233, #88063, #72284, #89100 ) ) ; +#35042 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35043 = CARTESIAN_POINT ( 'NONE', ( -1.215673047985899924, -1.210702855844099979, 0.8299999999999999600 ) ) ; +#35045 = EDGE_CURVE ( 'NONE', #45692, #15383, #24222, .T. ) ; +#35044 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#35046 = VECTOR ( 'NONE', #73793, 1000.000000000000000 ) ; +#35047 = STYLED_ITEM ( 'NONE', ( #99358 ), #98387 ) ; +#35048 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#35049 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35050 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35051 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35052 = EDGE_CURVE ( 'NONE', #5088, #68202, #21963, .T. ) ; +#35053 = EDGE_LOOP ( 'NONE', ( #48470, #14920, #50150, #83811 ) ) ; +#35054 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 1.696237999999999913, 0.8991599999999999593 ) ) ; +#35055 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8648700000000000276 ) ) ; +#35056 = EDGE_CURVE ( 'NONE', #80432, #92506, #88287, .T. ) ; +#35057 = DIRECTION ( 'NONE', ( -0.7071060119555152568, 0.7071075504167430026, 0.000000000000000000 ) ) ; +#35058 = CARTESIAN_POINT ( 'NONE', ( -1.876179938779914957, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#35059 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000005773, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#35060 = FACE_OUTER_BOUND ( 'NONE', #50028, .T. ) ; +#35061 = AXIS2_PLACEMENT_3D ( 'NONE', #100058, #46004, #85343 ) ; +#35062 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98354, 'distance_accuracy_value', 'NONE'); +#35063 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35064 = FILL_AREA_STYLE ('',( #5350 ) ) ; +#35065 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35066 = ORIENTED_EDGE ( 'NONE', *, *, #91994, .T. ) ; +#35067 = FILL_AREA_STYLE_COLOUR ( '', #84754 ) ; +#35068 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35069 = FACE_BOUND ( 'NONE', #19011, .T. ) ; +#35070 = CARTESIAN_POINT ( 'NONE', ( 0.4077210354193729902, -1.190630982187130149, 0.8300000000000015143 ) ) ; +#35071 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #113, #62434, #81297, #87908 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#35072 = FILL_AREA_STYLE_COLOUR ( '', #8837 ) ; +#35073 = VECTOR ( 'NONE', #82237, 1000.000000000000000 ) ; +#35074 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35075 = FILL_AREA_STYLE_COLOUR ( '', #61534 ) ; +#35076 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35077 = FILL_AREA_STYLE_COLOUR ( '', #46683 ) ; +#35078 = LINE ( 'NONE', #96302, #9769 ) ; +#35079 = EDGE_CURVE ( 'NONE', #65278, #69166, #16782, .T. ) ; +#35080 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35081 = VECTOR ( 'NONE', #40212, 1000.000000000000000 ) ; +#35082 = AXIS2_PLACEMENT_3D ( 'NONE', #50391, #82011, #58551 ) ; +#35083 = SURFACE_STYLE_USAGE ( .BOTH. , #28400 ) ; +#35084 = SURFACE_SIDE_STYLE ('',( #65698 ) ) ; +#35085 = PLANE ( 'NONE', #62071 ) ; +#35086 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.900000000000000133, 1.009450051515179092E-78 ) ) ; +#35087 = VECTOR ( 'NONE', #18422, 1000.000000000000000 ) ; +#35088 = FILL_AREA_STYLE_COLOUR ( '', #42226 ) ; +#35089 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #1952, 'design' ) ; +#35090 = LINE ( 'NONE', #49907, #80238 ) ; +#35091 = EDGE_CURVE ( 'NONE', #40649, #41417, #80145, .T. ) ; +#35092 = EDGE_LOOP ( 'NONE', ( #50843, #82941, #71978, #44013 ) ) ; +#35093 = PRESENTATION_STYLE_ASSIGNMENT (( #42239 ) ) ; +#35094 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81657, 'distance_accuracy_value', 'NONE'); +#35095 = STYLED_ITEM ( 'NONE', ( #63575 ), #88909 ) ; +#35096 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84733, 'distance_accuracy_value', 'NONE'); +#35098 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 6.650000000000000355, 0.000000000000000000 ) ) ; +#35097 = PRESENTATION_STYLE_ASSIGNMENT (( #88681 ) ) ; +#35099 = EDGE_CURVE ( 'NONE', #40310, #12693, #96412, .T. ) ; +#35100 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35101 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35102 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35103 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35104 = EDGE_LOOP ( 'NONE', ( #88356, #66384, #81639, #89565 ) ) ; +#35105 = FILL_AREA_STYLE_COLOUR ( '', #63542 ) ; +#35107 = ADVANCED_FACE ( 'NONE', ( #41335 ), #71961, .T. ) ; +#35106 = CYLINDRICAL_SURFACE ( 'NONE', #88097, 0.05000000000000012768 ) ; +#35108 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35109 = PRESENTATION_STYLE_ASSIGNMENT (( #67701 ) ) ; +#35110 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86223, 'distance_accuracy_value', 'NONE'); +#35111 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35112 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25385, 'distance_accuracy_value', 'NONE'); +#35113 = SURFACE_SIDE_STYLE ('',( #59102 ) ) ; +#35114 = ORIENTED_EDGE ( 'NONE', *, *, #13226, .T. ) ; +#35115 = ORIENTED_EDGE ( 'NONE', *, *, #49230, .T. ) ; +#35117 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59625 ), #93699 ) ; +#35116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7230 ), #61204 ) ; +#35118 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.076179938779915135, -0.02000000000000000042 ) ) ; +#35119 = SURFACE_SIDE_STYLE ('',( #89707 ) ) ; +#35120 = VERTEX_POINT ( 'NONE', #18299 ) ; +#35121 = SURFACE_STYLE_FILL_AREA ( #57608 ) ; +#35122 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#35123 = LINE ( 'NONE', #92683, #90821 ) ; +#35124 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.076179938779915135, 0.000000000000000000 ) ) ; +#35125 = ADVANCED_FACE ( 'NONE', ( #3016 ), #96227, .F. ) ; +#35126 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35127 = EDGE_CURVE ( 'NONE', #100016, #33366, #96915, .T. ) ; +#35128 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30186 ), #48150 ) ; +#35130 = ORIENTED_EDGE ( 'NONE', *, *, #27768, .F. ) ; +#35129 = ORIENTED_EDGE ( 'NONE', *, *, #83287, .T. ) ; +#35131 = VERTEX_POINT ( 'NONE', #27022 ) ; +#35132 = VERTEX_POINT ( 'NONE', #67290 ) ; +#35133 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#35134 = STYLED_ITEM ( 'NONE', ( #28310 ), #12583 ) ; +#35135 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35137 = SURFACE_SIDE_STYLE ('',( #19789 ) ) ; +#35136 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#35138 = ORIENTED_EDGE ( 'NONE', *, *, #16506, .T. ) ; +#35139 = EDGE_CURVE ( 'NONE', #24875, #50949, #58183, .T. ) ; +#35140 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35141 = LINE ( 'NONE', #19793, #68494 ) ; +#35142 = EDGE_CURVE ( 'NONE', #84241, #86902, #98368, .T. ) ; +#35143 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35144 = CARTESIAN_POINT ( 'NONE', ( -1.361868870821330013, -0.9987792914302030534, 0.8100000000000000533 ) ) ; +#35145 = EDGE_LOOP ( 'NONE', ( #87846, #56253, #82779, #88232 ) ) ; +#35146 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59651 ), #58042 ) ; +#35147 = SURFACE_STYLE_USAGE ( .BOTH. , #3965 ) ; +#35148 = ORIENTED_EDGE ( 'NONE', *, *, #76679, .T. ) ; +#35149 = ORIENTED_EDGE ( 'NONE', *, *, #20924, .F. ) ; +#35150 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35151 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91914 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62196, #23889, #86656 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35152 = CARTESIAN_POINT ( 'NONE', ( 1.901168164643999958, -1.316888414733939916, 0.8300000000000004041 ) ) ; +#35153 = FILL_AREA_STYLE ('',( #34644 ) ) ; +#35154 = ORIENTED_EDGE ( 'NONE', *, *, #49441, .F. ) ; +#35155 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8991599999999999593 ) ) ; +#35156 = VERTEX_POINT ( 'NONE', #4017 ) ; +#35157 = ADVANCED_FACE ( 'NONE', ( #90279 ), #35194, .T. ) ; +#35158 = SURFACE_SIDE_STYLE ('',( #2482 ) ) ; +#35159 = AXIS2_PLACEMENT_3D ( 'NONE', #98826, #13570, #82118 ) ; +#35160 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35161 = EDGE_LOOP ( 'NONE', ( #2148, #20668, #9671, #38238, #74301, #87796, #82420, #33122, #52834, #14353, #30776, #56140, #42983, #42649, #77777, #15431, #37493, #35877, #14624, #83748, #33172, #92717, #56623, #91139, #100718, #16476, #31512, #19401, #84472, #40257, #30725, #88238, #50074, #50461, #27555, #9674, #81050, #28165, #13210, #69171, #39437, #97940, #72813, #59065, #1045, #82831, #68, #96358, #10519, #6193, #36011, #376, #74572, #57238, #10730, #43316, #78622, #14718, #70629, #71888 ) ) ; +#35162 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#35163 = FILL_AREA_STYLE ('',( #21308 ) ) ; +#35164 = ORIENTED_EDGE ( 'NONE', *, *, #174, .T. ) ; +#35165 = VERTEX_POINT ( 'NONE', #61679 ) ; +#35166 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35167 = ADVANCED_FACE ( 'NONE', ( #53995 ), #22864, .T. ) ; +#35168 = AXIS2_PLACEMENT_3D ( 'NONE', #33626, #26966, #3480 ) ; +#35169 = PLANE ( 'NONE', #67809 ) ; +#35170 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35171 = STYLED_ITEM ( 'NONE', ( #18007 ), #78243 ) ; +#35172 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41696 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9121, #45944, #30637 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35173 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#35174 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #76309, #71687 ), + ( #40566, #79866 ), + ( #56901, #9814 ), + ( #94117, #94642 ), + ( #55393, #31872 ), + ( #1762, #86504 ), + ( #18029, #47695 ), + ( #48225, #32389 ), + ( #41069, #80371 ), + ( #24759, #9316 ), + ( #49743, #87502 ), + ( #78838, #72194 ), + ( #2258, #32890 ), + ( #72695, #55884 ), + ( #33404, #39530 ), + ( #64034, #88014 ), + ( #33915, #2755 ), + ( #87017, #95133 ), + ( #8299, #25260 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07237848055891020482, 0.1407192550564320133, 0.2049521751864399888, 0.2662164852627100231, 0.3253698271746789938, 0.3835875598417520238, 0.4415017690754730051, 0.4993597690990220217, 0.5575367350798919874, 0.6164546912842580051, 0.6759371479080940048, 0.7372987486091709952, 0.8002568593343240000, 0.8649063342747660421, 0.9311109296293510473, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#35175 = ADVANCED_FACE ( 'NONE', ( #84134 ), #54523, .F. ) ; +#35176 = ORIENTED_EDGE ( 'NONE', *, *, #96045, .F. ) ; +#35177 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64526 ), #54700 ) ; +#35178 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.8100000000000000533 ) ) ; +#35179 = ORIENTED_EDGE ( 'NONE', *, *, #69290, .T. ) ; +#35180 = EDGE_CURVE ( 'NONE', #60257, #63639, #7939, .T. ) ; +#35181 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, -8.400000000000000355, -11.41999999999999993 ) ) ; +#35182 = PRESENTATION_STYLE_ASSIGNMENT (( #89768 ) ) ; +#35183 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.000000000000000000 ) ) ; +#35184 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35185 = SURFACE_STYLE_FILL_AREA ( #58176 ) ; +#35187 = AXIS2_PLACEMENT_3D ( 'NONE', #41241, #43591, #90575 ) ; +#35186 = SURFACE_STYLE_FILL_AREA ( #25507 ) ; +#35188 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35189 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.9000000000000013545, 0.1829999999999620541 ) ) ; +#35190 = ORIENTED_EDGE ( 'NONE', *, *, #78570, .F. ) ; +#35191 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34844 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29100, #76053, #90365 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35192 = LINE ( 'NONE', #42824, #31381 ) ; +#35193 = PLANE ( 'NONE', #22747 ) ; +#35194 = PLANE ( 'NONE', #29824 ) ; +#35195 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#35196 = LINE ( 'NONE', #4505, #18997 ) ; +#35197 = FILL_AREA_STYLE ('',( #28030 ) ) ; +#35198 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#35199 = LINE ( 'NONE', #89786, #89144 ) ; +#35200 = VECTOR ( 'NONE', #11109, 1000.000000000000000 ) ; +#35201 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35202 = EDGE_CURVE ( 'NONE', #83292, #71259, #65599, .T. ) ; +#35203 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35204 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35206 = VECTOR ( 'NONE', #39984, 1000.000000000000000 ) ; +#35207 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31926, 'distance_accuracy_value', 'NONE'); +#35208 = VERTEX_POINT ( 'NONE', #92281 ) ; +#35209 = CARTESIAN_POINT ( 'NONE', ( 1.519746594691179897, -1.031932509624860161, 0.8299999999999999600 ) ) ; +#35211 = EDGE_CURVE ( 'NONE', #21395, #85325, #53504, .T. ) ; +#35210 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35212 = ORIENTED_EDGE ( 'NONE', *, *, #91272, .F. ) ; +#35213 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35214 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#35215 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#35216 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35217 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35218 = EDGE_CURVE ( 'NONE', #85966, #93113, #70308, .T. ) ; +#35219 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35220 = LINE ( 'NONE', #25042, #26936 ) ; +#35221 = DIRECTION ( 'NONE', ( 0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#35222 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51477 ) ) ; +#35223 = ORIENTED_EDGE ( 'NONE', *, *, #79198, .F. ) ; +#35224 = ORIENTED_EDGE ( 'NONE', *, *, #8969, .F. ) ; +#35225 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #60127 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#35226 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.01000000000000000021, -1.250000000000000000 ) ) ; +#35227 = ADVANCED_FACE ( 'NONE', ( #94275 ), #25895, .F. ) ; +#35228 = PRESENTATION_STYLE_ASSIGNMENT (( #28535 ) ) ; +#35229 = CARTESIAN_POINT ( 'NONE', ( -0.5167618201584639470, -1.182153033657940000, 0.8100000000000000533 ) ) ; +#35230 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24553, 'distance_accuracy_value', 'NONE'); +#35231 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46665, #14977, #76811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35232 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35233 = CARTESIAN_POINT ( 'NONE', ( 8.093173083250119859, 8.385468916749960755, 0.8648700000000000276 ) ) ; +#35234 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98045, 'distance_accuracy_value', 'NONE'); +#35235 = AXIS2_PLACEMENT_3D ( 'NONE', #87895, #70553, #55765 ) ; +#35236 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963070999999999344, 0.8648700000000000276 ) ) ; +#35237 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#35238 = VERTEX_POINT ( 'NONE', #71328 ) ; +#35239 = STYLED_ITEM ( 'NONE', ( #77295 ), #82990 ) ; +#35240 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61325 ) ) ; +#35241 = AXIS2_PLACEMENT_3D ( 'NONE', #43454, #98009, #6091 ) ; +#35242 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#35243 = ORIENTED_EDGE ( 'NONE', *, *, #32808, .F. ) ; +#35244 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35245 = VECTOR ( 'NONE', #29309, 1000.000000000000000 ) ; +#35246 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8648700000000000276 ) ) ; +#35247 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35248 = SURFACE_STYLE_FILL_AREA ( #90332 ) ; +#35249 = EDGE_CURVE ( 'NONE', #87301, #87086, #98431, .T. ) ; +#35250 = ADVANCED_FACE ( 'NONE', ( #63690 ), #72848, .T. ) ; +#35251 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.000000000000000000 ) ) ; +#35252 = CARTESIAN_POINT ( 'NONE', ( -1.153771935001989934, -0.9546485130184679813, 0.8299999999999999600 ) ) ; +#35253 = CARTESIAN_POINT ( 'NONE', ( -0.4878449414651300775, -0.9061750041553330304, 0.8100000000000000533 ) ) ; +#35254 = CARTESIAN_POINT ( 'NONE', ( -0.1692760792934966396, 1.036393530150319986, 0.8100000000000001643 ) ) ; +#35255 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#35257 = ORIENTED_EDGE ( 'NONE', *, *, #87651, .F. ) ; +#35256 = ORIENTED_EDGE ( 'NONE', *, *, #42770, .T. ) ; +#35258 = AXIS2_PLACEMENT_3D ( 'NONE', #79636, #80141, #41826 ) ; +#35259 = SURFACE_SIDE_STYLE ('',( #58741 ) ) ; +#35260 = ORIENTED_EDGE ( 'NONE', *, *, #79906, .T. ) ; +#35261 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#35262 = AXIS2_PLACEMENT_3D ( 'NONE', #21499, #98519, #99514 ) ; +#35263 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35264 = VERTEX_POINT ( 'NONE', #33558 ) ; +#35265 = VERTEX_POINT ( 'NONE', #80017 ) ; +#35267 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77568 ), #64533 ) ; +#35266 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35268 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000021, 0.2250000000000000333 ) ) ; +#35269 = EDGE_CURVE ( 'NONE', #6630, #55863, #98347, .T. ) ; +#35270 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35271 = SURFACE_STYLE_USAGE ( .BOTH. , #10134 ) ; +#35272 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#35274 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35273 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35275 = ORIENTED_EDGE ( 'NONE', *, *, #69446, .T. ) ; +#35276 = ORIENTED_EDGE ( 'NONE', *, *, #47189, .F. ) ; +#35277 = ADVANCED_FACE ( 'NONE', ( #64679 ), #95783, .T. ) ; +#35278 = SURFACE_SIDE_STYLE ('',( #58263 ) ) ; +#35279 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83194 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43850, #12640, #39710 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35280 = EDGE_LOOP ( 'NONE', ( #79074, #55977, #27211, #74016 ) ) ; +#35281 = FACE_OUTER_BOUND ( 'NONE', #77150, .T. ) ; +#35282 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#35283 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54946 ), #84140 ) ; +#35284 = VECTOR ( 'NONE', #72925, 1000.000000000000000 ) ; +#35286 = EDGE_LOOP ( 'NONE', ( #56105, #35640, #23051, #94614 ) ) ; +#35285 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35287 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40141 ), #28683 ) ; +#35288 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.3666666666666686392, 0.000000000000000000 ) ) ; +#35289 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#35290 = ORIENTED_EDGE ( 'NONE', *, *, #46431, .F. ) ; +#35291 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.000000000000000000 ) ) ; +#35292 = EDGE_LOOP ( 'NONE', ( #56839, #61162, #95371, #10774 ) ) ; +#35293 = ORIENTED_EDGE ( 'NONE', *, *, #61248, .T. ) ; +#35294 = LINE ( 'NONE', #29109, #38921 ) ; +#35295 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#35296 = FACE_OUTER_BOUND ( 'NONE', #53180, .T. ) ; +#35297 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#35298 = VECTOR ( 'NONE', #53230, 1000.000000000000000 ) ; +#35299 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35300 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#35301 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#35303 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35302 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8299999999999999600 ) ) ; +#35304 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35305 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35306 = ORIENTED_EDGE ( 'NONE', *, *, #53231, .T. ) ; +#35307 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35308 = SURFACE_STYLE_FILL_AREA ( #41939 ) ; +#35309 = ORIENTED_EDGE ( 'NONE', *, *, #4313, .F. ) ; +#35310 = ADVANCED_FACE ( 'NONE', ( #49887 ), #100141, .T. ) ; +#35311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35312 = CARTESIAN_POINT ( 'NONE', ( -0.1950643281718389965, -1.495500525511030077, 0.8100000000000000533 ) ) ; +#35313 = LINE ( 'NONE', #58795, #48222 ) ; +#35314 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27948 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8789, #1752, #94635 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35315 = STYLED_ITEM ( 'NONE', ( #9322 ), #90455 ) ; +#35316 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98733 ) ) ; +#35317 = ADVANCED_FACE ( 'NONE', ( #59068 ), #13081, .F. ) ; +#35318 = SURFACE_STYLE_USAGE ( .BOTH. , #18428 ) ; +#35319 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96328 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31101, #63779, #94862 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35320 = FACE_OUTER_BOUND ( 'NONE', #43441, .T. ) ; +#35321 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35322 = SURFACE_STYLE_FILL_AREA ( #35820 ) ; +#35323 = VECTOR ( 'NONE', #58733, 1000.000000000000000 ) ; +#35324 = EDGE_LOOP ( 'NONE', ( #72527, #66230, #69194, #93675 ) ) ; +#35325 = SURFACE_STYLE_FILL_AREA ( #4141 ) ; +#35326 = EDGE_CURVE ( 'NONE', #50722, #702, #22734, .T. ) ; +#35329 = SURFACE_STYLE_FILL_AREA ( #57815 ) ; +#35328 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35327 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35330 = CARTESIAN_POINT ( 'NONE', ( 7.386066124875000583, 9.092575124875001080, 0.8648700000000000276 ) ) ; +#35331 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#35332 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35333 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4949, 'distance_accuracy_value', 'NONE'); +#35334 = ORIENTED_EDGE ( 'NONE', *, *, #54732, .F. ) ; +#35335 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#35336 = EDGE_CURVE ( 'NONE', #45524, #2733, #63295, .T. ) ; +#35337 = PRESENTATION_STYLE_ASSIGNMENT (( #56808 ) ) ; +#35338 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35339 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25656 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #476, #68895, #77588 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35340 = FILL_AREA_STYLE_COLOUR ( '', #83637 ) ; +#35341 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28727 ), #49988 ) ; +#35342 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35343 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35344 = SURFACE_SIDE_STYLE ('',( #73610 ) ) ; +#35345 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#35346 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35347 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35348 = EDGE_LOOP ( 'NONE', ( #99465, #77656, #37433, #56494 ) ) ; +#35349 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35350 = ORIENTED_EDGE ( 'NONE', *, *, #90553, .F. ) ; +#35351 = AXIS2_PLACEMENT_3D ( 'NONE', #37018, #21180, #28349 ) ; +#35352 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.416666666666666519, 0.000000000000000000 ) ) ; +#35353 = EDGE_CURVE ( 'NONE', #8666, #79176, #45173, .T. ) ; +#35354 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12817, 'distance_accuracy_value', 'NONE'); +#35355 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35356 = LINE ( 'NONE', #50665, #52940 ) ; +#35357 = PLANE ( 'NONE', #93357 ) ; +#35358 = VECTOR ( 'NONE', #27325, 1000.000000000000000 ) ; +#35359 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, 0.000000000000000000 ) ) ; +#35360 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35361 = FILL_AREA_STYLE_COLOUR ( '', #1252 ) ; +#35362 = FILL_AREA_STYLE ('',( #90441 ) ) ; +#35363 = VERTEX_POINT ( 'NONE', #68661 ) ; +#35364 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.1200000000000003147, 0.4000000000000000222 ) ) ; +#35365 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 1.899999999999999911, 0.000000000000000000 ) ) ; +#35366 = ORIENTED_EDGE ( 'NONE', *, *, #74651, .F. ) ; +#35367 = SURFACE_SIDE_STYLE ('',( #9751 ) ) ; +#35368 = PLANE ( 'NONE', #17426 ) ; +#35369 = VERTEX_POINT ( 'NONE', #29868 ) ; +#35370 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#35371 = ADVANCED_FACE ( 'NONE', ( #14516 ), #45667, .F. ) ; +#35372 = EDGE_CURVE ( 'NONE', #82400, #52824, #8322, .T. ) ; +#35373 = PRESENTATION_STYLE_ASSIGNMENT (( #36350 ) ) ; +#35374 = AXIS2_PLACEMENT_3D ( 'NONE', #18939, #4133, #35813 ) ; +#35375 = VERTEX_POINT ( 'NONE', #16542 ) ; +#35377 = ADVANCED_FACE ( 'NONE', ( #94151 ), #87038, .T. ) ; +#35376 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#35378 = ADVANCED_FACE ( 'NONE', ( #2285 ), #41590, .T. ) ; +#35379 = ORIENTED_EDGE ( 'NONE', *, *, #30148, .T. ) ; +#35380 = SURFACE_STYLE_FILL_AREA ( #10758 ) ; +#35381 = AXIS2_PLACEMENT_3D ( 'NONE', #754, #23754, #86022 ) ; +#35382 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77753 ) ) ; +#35383 = FILL_AREA_STYLE ('',( #10762 ) ) ; +#35384 = ORIENTED_EDGE ( 'NONE', *, *, #75207, .T. ) ; +#35385 = VECTOR ( 'NONE', #46299, 1000.000000000000114 ) ; +#35386 = ORIENTED_EDGE ( 'NONE', *, *, #18686, .T. ) ; +#35387 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61240 ), #17401 ) ; +#35388 = FILL_AREA_STYLE_COLOUR ( '', #33532 ) ; +#35390 = ADVANCED_FACE ( 'NONE', ( #26276 ), #67055, .F. ) ; +#35389 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35391 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35392 = VECTOR ( 'NONE', #87494, 1000.000000000000000 ) ; +#35394 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#35393 = CARTESIAN_POINT ( 'NONE', ( 0.3500290314248439838, -0.9624968822990390693, 0.8299999999999999600 ) ) ; +#35395 = ORIENTED_EDGE ( 'NONE', *, *, #90875, .F. ) ; +#35397 = ORIENTED_EDGE ( 'NONE', *, *, #94604, .T. ) ; +#35396 = ORIENTED_EDGE ( 'NONE', *, *, #20931, .F. ) ; +#35398 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#35399 = EDGE_LOOP ( 'NONE', ( #32742, #58105, #56005, #52266 ) ) ; +#35400 = EDGE_CURVE ( 'NONE', #60878, #40659, #19592, .T. ) ; +#35401 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#35402 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37207 ), #98816 ) ; +#35403 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35404 = ORIENTED_EDGE ( 'NONE', *, *, #35454, .F. ) ; +#35406 = ORIENTED_EDGE ( 'NONE', *, *, #83376, .T. ) ; +#35405 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35407 = SURFACE_SIDE_STYLE ('',( #49198 ) ) ; +#35408 = EDGE_LOOP ( 'NONE', ( #5163, #20407, #22170, #1195 ) ) ; +#35409 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#35410 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35411 = EDGE_LOOP ( 'NONE', ( #29561, #9504, #66386, #2944 ) ) ; +#35412 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51718 ), #76106 ) ; +#35413 = LINE ( 'NONE', #96630, #39927 ) ; +#35414 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71231 ) ) ; +#35415 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#35416 = SURFACE_STYLE_USAGE ( .BOTH. , #4234 ) ; +#35417 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#35418 = VECTOR ( 'NONE', #48019, 1000.000000000000000 ) ; +#35419 = FILL_AREA_STYLE_COLOUR ( '', #49316 ) ; +#35420 = CARTESIAN_POINT ( 'NONE', ( 1.820901995646819982, -1.357122040133029950, 0.8299999999999999600 ) ) ; +#35422 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#35421 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2166666666666666463, 0.000000000000000000 ) ) ; +#35423 = FACE_OUTER_BOUND ( 'NONE', #1850, .T. ) ; +#35424 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#35425 = VERTEX_POINT ( 'NONE', #59451 ) ; +#35426 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#35427 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82694 ), #4191 ) ; +#35428 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35429 = CARTESIAN_POINT ( 'NONE', ( 1.314694272500980032, -1.181578794826660284, 0.8300000000000022915 ) ) ; +#35430 = EDGE_CURVE ( 'NONE', #16114, #67005, #43564, .T. ) ; +#35432 = PRESENTATION_STYLE_ASSIGNMENT (( #2752 ) ) ; +#35431 = FACE_OUTER_BOUND ( 'NONE', #22941, .T. ) ; +#35433 = LINE ( 'NONE', #15899, #89428 ) ; +#35434 = AXIS2_PLACEMENT_3D ( 'NONE', #18213, #8484, #17227 ) ; +#35435 = FILL_AREA_STYLE_COLOUR ( '', #44328 ) ; +#35436 = STYLED_ITEM ( 'NONE', ( #57161 ), #73889 ) ; +#35437 = EDGE_LOOP ( 'NONE', ( #3968, #63519, #68394, #75308 ) ) ; +#35438 = FACE_OUTER_BOUND ( 'NONE', #57253, .T. ) ; +#35439 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, 0.000000000000000000 ) ) ; +#35440 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.000000000000000000 ) ) ; +#35441 = ORIENTED_EDGE ( 'NONE', *, *, #96878, .T. ) ; +#35442 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92439 ) ) ; +#35443 = FILL_AREA_STYLE ('',( #4264 ) ) ; +#35445 = FILL_AREA_STYLE_COLOUR ( '', #24929 ) ; +#35444 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35446 = CARTESIAN_POINT ( 'NONE', ( 1.568874050374579943, -1.341601374162270321, 0.8099999999999976108 ) ) ; +#35447 = SURFACE_STYLE_FILL_AREA ( #73229 ) ; +#35448 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000001184, 0.8991599999999999593 ) ) ; +#35449 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72954 ) ) ; +#35450 = STYLED_ITEM ( 'NONE', ( #74356 ), #91002 ) ; +#35451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35452 = EDGE_LOOP ( 'NONE', ( #20379, #6992, #5524, #56363 ) ) ; +#35453 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79456 ) ) ; +#35454 = EDGE_CURVE ( 'NONE', #88940, #72784, #26777, .T. ) ; +#35455 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#35456 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 8.031915000000001470, 0.8648700000000000276 ) ) ; +#35457 = SURFACE_SIDE_STYLE ('',( #26275 ) ) ; +#35458 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#35459 = PLANE ( 'NONE', #78525 ) ; +#35460 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.7000000000000005107, -0.02000000000001675091 ) ) ; +#35461 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#35462 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#35463 = PRESENTATION_STYLE_ASSIGNMENT (( #74240 ) ) ; +#35464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #403 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92208, #22275, #46220 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35465 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35466 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2868 ), #55059 ) ; +#35467 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#35468 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35469 = ORIENTED_EDGE ( 'NONE', *, *, #34697, .T. ) ; +#35470 = FILL_AREA_STYLE_COLOUR ( '', #64461 ) ; +#35471 = VERTEX_POINT ( 'NONE', #81419 ) ; +#35472 = SURFACE_SIDE_STYLE ('',( #66567 ) ) ; +#35473 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22491 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29879, #22743, #85519 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35475 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12546 ) ) ; +#35474 = CARTESIAN_POINT ( 'NONE', ( -1.325742936027486163, -1.458506469577147469, 0.8099999999996504441 ) ) ; +#35476 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35477 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35478 = LINE ( 'NONE', #26801, #92410 ) ; +#35479 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35480 = CLOSED_SHELL ( 'NONE', ( #70898, #3861, #72118, #12833, #80751, #61888 ) ) ; +#35481 = VERTEX_POINT ( 'NONE', #66554 ) ; +#35482 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#35483 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76107 ), #9266 ) ; +#35484 = ORIENTED_EDGE ( 'NONE', *, *, #70606, .T. ) ; +#35485 = SURFACE_STYLE_USAGE ( .BOTH. , #80426 ) ; +#35486 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98912 ), #84352 ) ; +#35487 = CARTESIAN_POINT ( 'NONE', ( 1.248152242693560066, -1.513291690750319995, 0.8299999999999994049 ) ) ; +#35488 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35489 = FILL_AREA_STYLE ('',( #4316 ) ) ; +#35490 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#35491 = ORIENTED_EDGE ( 'NONE', *, *, #2001, .F. ) ; +#35492 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35493 = SURFACE_STYLE_USAGE ( .BOTH. , #81463 ) ; +#35494 = EDGE_CURVE ( 'NONE', #64000, #82873, #47333, .T. ) ; +#35495 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35496 = LINE ( 'NONE', #65100, #54033 ) ; +#35497 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#35498 = VERTEX_POINT ( 'NONE', #90549 ) ; +#35499 = FACE_OUTER_BOUND ( 'NONE', #14609, .T. ) ; +#35500 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999998935, 8.286472999999999089, 0.8991599999999999593 ) ) ; +#35501 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64703 ), #38671 ) ; +#35502 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#35503 = CARTESIAN_POINT ( 'NONE', ( -1.141528815712065992, -1.227738040490839344, 0.8099999999998204192 ) ) ; +#35504 = ORIENTED_EDGE ( 'NONE', *, *, #85623, .F. ) ; +#35505 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35506 = EDGE_CURVE ( 'NONE', #75030, #70963, #50985, .T. ) ; +#35507 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35508 = VERTEX_POINT ( 'NONE', #96175 ) ; +#35510 = VERTEX_POINT ( 'NONE', #88541 ) ; +#35509 = LINE ( 'NONE', #21159, #91580 ) ; +#35511 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97850, 'distance_accuracy_value', 'NONE'); +#35512 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#35514 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8100000000000000533 ) ) ; +#35513 = FILL_AREA_STYLE_COLOUR ( '', #99774 ) ; +#35515 = LINE ( 'NONE', #27857, #747 ) ; +#35516 = PLANE ( 'NONE', #19445 ) ; +#35517 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35518 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35519 = FILL_AREA_STYLE_COLOUR ( '', #91533 ) ; +#35520 = ORIENTED_EDGE ( 'NONE', *, *, #49474, .F. ) ; +#35521 = VECTOR ( 'NONE', #88546, 1000.000000000000000 ) ; +#35522 = CARTESIAN_POINT ( 'NONE', ( 1.227431534468609975, -1.515241174392790047, 0.8100000000000000533 ) ) ; +#35523 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6725, #47122, #38971, #100128 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#35524 = FACE_OUTER_BOUND ( 'NONE', #54508, .T. ) ; +#35525 = VERTEX_POINT ( 'NONE', #18575 ) ; +#35526 = AXIS2_PLACEMENT_3D ( 'NONE', #5824, #82985, #44163 ) ; +#35527 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35528 = EDGE_LOOP ( 'NONE', ( #55361, #3013, #81171, #68850 ) ) ; +#35530 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, -9.486769009248163798E-17, -0.6199999999999999956 ) ) ; +#35529 = CARTESIAN_POINT ( 'NONE', ( 0.2117005300540794610, -1.331872137722204252, 0.8100000000000001643 ) ) ; +#35531 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35532 = STYLED_ITEM ( 'NONE', ( #45424 ), #24749 ) ; +#35533 = VECTOR ( 'NONE', #71974, 1000.000000000000000 ) ; +#35534 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35535 = VERTEX_POINT ( 'NONE', #76217 ) ; +#35536 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15704 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57220, #96459, #11133 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35537 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.499999999999989786, 0.1829999999999999960 ) ) ; +#35538 = VERTEX_POINT ( 'NONE', #28752 ) ; +#35539 = STYLED_ITEM ( 'NONE', ( #12139 ), #23246 ) ; +#35540 = ORIENTED_EDGE ( 'NONE', *, *, #28980, .T. ) ; +#35541 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35542 = CLOSED_SHELL ( 'NONE', ( #34534, #60964, #65279, #16710, #44143, #52173 ) ) ; +#35543 = EDGE_CURVE ( 'NONE', #10498, #84594, #37928, .T. ) ; +#35545 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35544 = FILL_AREA_STYLE ('',( #97266 ) ) ; +#35546 = CARTESIAN_POINT ( 'NONE', ( -1.371290353842550047, -1.066576130479129914, 0.8100000000000000533 ) ) ; +#35547 = AXIS2_PLACEMENT_3D ( 'NONE', #25276, #4144, #35328 ) ; +#35548 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35549 = VECTOR ( 'NONE', #76004, 1000.000000000000000 ) ; +#35551 = CARTESIAN_POINT ( 'NONE', ( 0.3504973566725850254, -1.231551917075010216, 0.8100000000000000533 ) ) ; +#35550 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #87631, #82894 ), #55160 ) ; +#35552 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35553 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35554 = FILL_AREA_STYLE_COLOUR ( '', #24235 ) ; +#35555 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#35556 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50223 ) ) ; +#35557 = ORIENTED_EDGE ( 'NONE', *, *, #127, .T. ) ; +#35558 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.627715291671302177E-18, 0.6500000000000001332 ) ) ; +#35559 = SURFACE_STYLE_FILL_AREA ( #4373 ) ; +#35560 = AXIS2_PLACEMENT_3D ( 'NONE', #94425, #71981, #31651 ) ; +#35563 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35562 = LINE ( 'NONE', #27377, #94651 ) ; +#35561 = SURFACE_STYLE_FILL_AREA ( #51871 ) ; +#35564 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35477, 'distance_accuracy_value', 'NONE'); +#35565 = VECTOR ( 'NONE', #20096, 1000.000000000000000 ) ; +#35566 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35567 = SURFACE_STYLE_USAGE ( .BOTH. , #97290 ) ; +#35568 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35569 = ORIENTED_EDGE ( 'NONE', *, *, #22169, .F. ) ; +#35570 = FACE_OUTER_BOUND ( 'NONE', #4152, .T. ) ; +#35571 = EDGE_CURVE ( 'NONE', #22678, #59623, #67283, .T. ) ; +#35572 = FILL_AREA_STYLE ('',( #89167 ) ) ; +#35573 = SURFACE_STYLE_USAGE ( .BOTH. , #34060 ) ; +#35574 = PRESENTATION_STYLE_ASSIGNMENT (( #4389 ) ) ; +#35575 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73985 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36853, #99024, #97580 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35576 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6097 ), #66517 ) ; +#35577 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35578 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35579 = EDGE_CURVE ( 'NONE', #31593, #7937, #44558, .T. ) ; +#35580 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35581 = FILL_AREA_STYLE ('',( #35077 ) ) ; +#35582 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9377 ), #17597 ) ; +#35583 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#35584 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35585 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#35586 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35587 = AXIS2_PLACEMENT_3D ( 'NONE', #88471, #72644, #94070 ) ; +#35588 = LINE ( 'NONE', #3430, #9500 ) ; +#35589 = VECTOR ( 'NONE', #29897, 1000.000000000000000 ) ; +#35590 = STYLED_ITEM ( 'NONE', ( #49637 ), #91480 ) ; +#35591 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#35592 = SURFACE_STYLE_FILL_AREA ( #26915 ) ; +#35593 = PRESENTATION_STYLE_ASSIGNMENT (( #19215 ) ) ; +#35594 = ADVANCED_FACE ( 'NONE', ( #92518 ), #45530, .T. ) ; +#35595 = ORIENTED_EDGE ( 'NONE', *, *, #48763, .T. ) ; +#35596 = FILL_AREA_STYLE ('',( #81568 ) ) ; +#35597 = EDGE_CURVE ( 'NONE', #88593, #97577, #3669, .T. ) ; +#35598 = SURFACE_STYLE_FILL_AREA ( #73876 ) ; +#35600 = FILL_AREA_STYLE ('',( #84045 ) ) ; +#35599 = FILL_AREA_STYLE_COLOUR ( '', #54140 ) ; +#35601 = PLANE ( 'NONE', #5058 ) ; +#35602 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26935 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22688, #100655, #45126 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35603 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, -0.000000000000000000 ) ) ; +#35604 = ORIENTED_EDGE ( 'NONE', *, *, #80221, .T. ) ; +#35605 = VECTOR ( 'NONE', #58579, 1000.000000000000000 ) ; +#35606 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#35607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97500 ) ) ; +#35608 = VERTEX_POINT ( 'NONE', #98616 ) ; +#35609 = PRESENTATION_STYLE_ASSIGNMENT (( #74392 ) ) ; +#35610 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29017 ) ) ; +#35611 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8199999999999999512 ) ) ; +#35612 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35613 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24165 ), #90977 ) ; +#35614 = CLOSED_SHELL ( 'NONE', ( #84831, #23362, #26133, #52632, #87568, #97434 ) ) ; +#35615 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#35616 = ORIENTED_EDGE ( 'NONE', *, *, #22730, .T. ) ; +#35617 = ORIENTED_EDGE ( 'NONE', *, *, #99752, .T. ) ; +#35618 = AXIS2_PLACEMENT_3D ( 'NONE', #80180, #10101, #17849 ) ; +#35619 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#35620 = ORIENTED_EDGE ( 'NONE', *, *, #13107, .F. ) ; +#35621 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#35622 = STYLED_ITEM ( 'NONE', ( #100625 ), #50539 ) ; +#35623 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35624 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35625 = SURFACE_STYLE_USAGE ( .BOTH. , #42265 ) ; +#35626 = STYLED_ITEM ( 'NONE', ( #43832 ), #14981 ) ; +#35627 = ADVANCED_FACE ( 'NONE', ( #53745 ), #22100, .T. ) ; +#35628 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #76934, #48366 ) ; +#35629 = SURFACE_STYLE_USAGE ( .BOTH. , #55594 ) ; +#35630 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35632 = VERTEX_POINT ( 'NONE', #61934 ) ; +#35631 = ORIENTED_EDGE ( 'NONE', *, *, #19461, .F. ) ; +#35633 = ORIENTED_EDGE ( 'NONE', *, *, #30683, .T. ) ; +#35634 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66570 ), #69756 ) ; +#35635 = ORIENTED_EDGE ( 'NONE', *, *, #58933, .F. ) ; +#35636 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35637 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25628, 'distance_accuracy_value', 'NONE'); +#35639 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35638 = CYLINDRICAL_SURFACE ( 'NONE', #67167, 0.05000000000000012768 ) ; +#35640 = ORIENTED_EDGE ( 'NONE', *, *, #14983, .T. ) ; +#35641 = PRESENTATION_STYLE_ASSIGNMENT (( #96860 ) ) ; +#35642 = SURFACE_STYLE_USAGE ( .BOTH. , #50471 ) ; +#35643 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #76779, .NOT_KNOWN. ) ; +#35644 = LINE ( 'NONE', #21787, #18860 ) ; +#35645 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84031 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22354, #93275, #7459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35647 = EDGE_LOOP ( 'NONE', ( #92323, #68586, #76914, #47534 ) ) ; +#35646 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35649 = PLANE ( 'NONE', #69583 ) ; +#35648 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35650 = ORIENTED_EDGE ( 'NONE', *, *, #71663, .F. ) ; +#35651 = EDGE_LOOP ( 'NONE', ( #6652, #93543, #9527, #27506 ) ) ; +#35652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35653 = STYLED_ITEM ( 'NONE', ( #72208 ), #31215 ) ; +#35654 = ADVANCED_FACE ( 'NONE', ( #54263 ), #85386, .F. ) ; +#35656 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8648700000000000276 ) ) ; +#35655 = LINE ( 'NONE', #13059, #91868 ) ; +#35657 = CARTESIAN_POINT ( 'NONE', ( 1.890937141840999924, -1.269147371132230084, 0.8300000000000004041 ) ) ; +#35658 = FACE_OUTER_BOUND ( 'NONE', #10784, .T. ) ; +#35659 = VERTEX_POINT ( 'NONE', #39942 ) ; +#35660 = AXIS2_PLACEMENT_3D ( 'NONE', #32736, #8630, #9152 ) ; +#35661 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35662 = LINE ( 'NONE', #70531, #76455 ) ; +#35663 = VECTOR ( 'NONE', #33330, 1000.000000000000000 ) ; +#35664 = VERTEX_POINT ( 'NONE', #70056 ) ; +#35666 = FACE_OUTER_BOUND ( 'NONE', #78074, .T. ) ; +#35665 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#35667 = ORIENTED_EDGE ( 'NONE', *, *, #8189, .T. ) ; +#35668 = VERTEX_POINT ( 'NONE', #9216 ) ; +#35669 = EDGE_CURVE ( 'NONE', #81611, #95534, #40463, .T. ) ; +#35671 = LINE ( 'NONE', #3506, #20992 ) ; +#35670 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#35672 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35673 = FILL_AREA_STYLE_COLOUR ( '', #26376 ) ; +#35674 = FACE_OUTER_BOUND ( 'NONE', #82248, .T. ) ; +#35675 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#35677 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#35676 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92892, 'distance_accuracy_value', 'NONE'); +#35678 = ORIENTED_EDGE ( 'NONE', *, *, #62414, .T. ) ; +#35679 = VECTOR ( 'NONE', #21237, 1000.000000000000000 ) ; +#35680 = ORIENTED_EDGE ( 'NONE', *, *, #57625, .F. ) ; +#35681 = STYLED_ITEM ( 'NONE', ( #44170 ), #1034 ) ; +#35682 = FILL_AREA_STYLE ('',( #50999 ) ) ; +#35683 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35684 = CYLINDRICAL_SURFACE ( 'NONE', #73271, 0.05000000000000002359 ) ; +#35685 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#35686 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35687 = CARTESIAN_POINT ( 'NONE', ( 0.9366369866146585510, 0.4412590759269655050, 0.8100000000000000533 ) ) ; +#35688 = ORIENTED_EDGE ( 'NONE', *, *, #98920, .T. ) ; +#35689 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#35690 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35691 = CARTESIAN_POINT ( 'NONE', ( 0.2440989101500280201, -0.9342297348062970075, 0.8100000000000000533 ) ) ; +#35692 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#35693 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35694 = AXIS2_PLACEMENT_3D ( 'NONE', #98359, #66303, #10560 ) ; +#35695 = PLANE ( 'NONE', #30417 ) ; +#35696 = EDGE_CURVE ( 'NONE', #18495, #56225, #71600, .T. ) ; +#35698 = EDGE_CURVE ( 'NONE', #59367, #63516, #1044, .T. ) ; +#35697 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13098, 'distance_accuracy_value', 'NONE'); +#35699 = VECTOR ( 'NONE', #85651, 1000.000000000000000 ) ; +#35700 = SURFACE_STYLE_FILL_AREA ( #98864 ) ; +#35701 = PRESENTATION_STYLE_ASSIGNMENT (( #12108 ) ) ; +#35702 = FACE_OUTER_BOUND ( 'NONE', #96111, .T. ) ; +#35703 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#35704 = PLANE ( 'NONE', #27352 ) ; +#35705 = PRESENTATION_STYLE_ASSIGNMENT (( #60682 ) ) ; +#35706 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#35707 = CARTESIAN_POINT ( 'NONE', ( 1.341536415582540220, -1.062017517080650064, 0.8299999999999995159 ) ) ; +#35708 = ORIENTED_EDGE ( 'NONE', *, *, #32112, .F. ) ; +#35709 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#35710 = SURFACE_STYLE_FILL_AREA ( #14150 ) ; +#35711 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#35712 = EDGE_CURVE ( 'NONE', #23904, #21132, #47088, .T. ) ; +#35713 = EDGE_LOOP ( 'NONE', ( #32243, #48351, #63743, #28696 ) ) ; +#35714 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35715 = FILL_AREA_STYLE ('',( #81675 ) ) ; +#35716 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35717 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35718 = ADVANCED_FACE ( 'NONE', ( #1658 ), #78729, .F. ) ; +#35719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51962 ), #29139 ) ; +#35720 = EDGE_CURVE ( 'NONE', #67222, #94045, #47602, .T. ) ; +#35721 = CARTESIAN_POINT ( 'NONE', ( 1.416374102632393939, -1.046522010761860244, 0.8099999999999604183 ) ) ; +#35722 = STYLED_ITEM ( 'NONE', ( #58193 ), #31527 ) ; +#35723 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#35724 = ORIENTED_EDGE ( 'NONE', *, *, #61535, .T. ) ; +#35725 = ORIENTED_EDGE ( 'NONE', *, *, #17341, .T. ) ; +#35726 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94341 ) ) ; +#35727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1429 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71111, #32818, #10230 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34130 ), #53632 ) ; +#35729 = CARTESIAN_POINT ( 'NONE', ( -0.4442483664529159881, -1.083526083816420016, 0.8100000000000000533 ) ) ; +#35730 = EDGE_CURVE ( 'NONE', #46055, #40001, #46574, .T. ) ; +#35731 = SURFACE_STYLE_FILL_AREA ( #12134 ) ; +#35732 = FACE_OUTER_BOUND ( 'NONE', #64484, .T. ) ; +#35733 = SURFACE_SIDE_STYLE ('',( #50556 ) ) ; +#35734 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#35735 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4717 ), #65018 ) ; +#35736 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.008431457505076202924, 0.1458578643762690474 ) ) ; +#35737 = VERTEX_POINT ( 'NONE', #73105 ) ; +#35738 = EDGE_CURVE ( 'NONE', #86964, #30264, #26152, .T. ) ; +#35739 = SURFACE_STYLE_FILL_AREA ( #74533 ) ; +#35740 = AXIS2_PLACEMENT_3D ( 'NONE', #44903, #37305, #66911 ) ; +#35741 = EDGE_LOOP ( 'NONE', ( #58525, #58507, #36144, #77443 ) ) ; +#35742 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67434, #74115, #98012, #5618 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#35743 = SURFACE_SIDE_STYLE ('',( #4552 ) ) ; +#35744 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#35745 = SURFACE_STYLE_USAGE ( .BOTH. , #28551 ) ; +#35746 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35747 = EDGE_CURVE ( 'NONE', #75418, #67841, #66935, .T. ) ; +#35748 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#35749 = CARTESIAN_POINT ( 'NONE', ( -0.4700584699050159854, -0.9114593501573470258, 0.8299999999999999600 ) ) ; +#35750 = LINE ( 'NONE', #4070, #50673 ) ; +#35751 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#35752 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91836 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32569, #47368, #86678 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35753 = EDGE_CURVE ( 'NONE', #33091, #60865, #65422, .T. ) ; +#35755 = ORIENTED_EDGE ( 'NONE', *, *, #94715, .F. ) ; +#35754 = VERTEX_POINT ( 'NONE', #50648 ) ; +#35756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77275 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72701, #18033, #2262 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35757 = AXIS2_PLACEMENT_3D ( 'NONE', #68577, #93040, #83922 ) ; +#35758 = EDGE_LOOP ( 'NONE', ( #84941, #97601, #38013, #10386 ) ) ; +#35759 = FILL_AREA_STYLE ('',( #76521 ) ) ; +#35761 = PRESENTATION_STYLE_ASSIGNMENT (( #66860 ) ) ; +#35760 = LINE ( 'NONE', #60731, #88078 ) ; +#35762 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3147 ), #71594 ) ; +#35763 = EDGE_LOOP ( 'NONE', ( #33231, #8919, #56103 ) ) ; +#35764 = ORIENTED_EDGE ( 'NONE', *, *, #92500, .T. ) ; +#35765 = FILL_AREA_STYLE ('',( #75057 ) ) ; +#35766 = PLANE ( 'NONE', #65004 ) ; +#35768 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#35767 = SURFACE_STYLE_USAGE ( .BOTH. , #82705 ) ; +#35769 = VERTEX_POINT ( 'NONE', #72583 ) ; +#35770 = ORIENTED_EDGE ( 'NONE', *, *, #99957, .F. ) ; +#35771 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#35772 = EDGE_LOOP ( 'NONE', ( #63766, #53957, #72457, #54290 ) ) ; +#35773 = PRESENTATION_STYLE_ASSIGNMENT (( #65366 ) ) ; +#35774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79780 ) ) ; +#35775 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000000104, 0.2399999999999999911 ) ) ; +#35776 = EDGE_CURVE ( 'NONE', #86420, #45876, #27165, .T. ) ; +#35777 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35780 = ORIENTED_EDGE ( 'NONE', *, *, #48227, .F. ) ; +#35779 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6298 ), #76474 ) ; +#35778 = DIRECTION ( 'NONE', ( 4.344024262657780003E-34, 4.266452400824600274E-34, 1.000000000000000000 ) ) ; +#35781 = FILL_AREA_STYLE ('',( #97962 ) ) ; +#35782 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.500000000000000444, 0.000000000000000000 ) ) ; +#35783 = ORIENTED_EDGE ( 'NONE', *, *, #54577, .T. ) ; +#35784 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#35785 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#35786 = ORIENTED_EDGE ( 'NONE', *, *, #256, .T. ) ; +#35787 = ORIENTED_EDGE ( 'NONE', *, *, #30227, .F. ) ; +#35788 = EDGE_CURVE ( 'NONE', #67869, #68343, #57301, .T. ) ; +#35789 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.300000000000000266, -3.118622929693471946E-90 ) ) ; +#35790 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35791 = DIRECTION ( 'NONE', ( 0.9584246665703156642, -0.2853456824793028646, 0.000000000000000000 ) ) ; +#35792 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35793 = VECTOR ( 'NONE', #74308, 1000.000000000000114 ) ; +#35794 = FILL_AREA_STYLE ('',( #18410 ) ) ; +#35795 = EDGE_CURVE ( 'NONE', #86856, #63825, #96550, .T. ) ; +#35796 = FACE_OUTER_BOUND ( 'NONE', #75904, .T. ) ; +#35797 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#35798 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#35800 = FILL_AREA_STYLE_COLOUR ( '', #28671 ) ; +#35799 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35801 = VECTOR ( 'NONE', #60080, 1000.000000000000000 ) ; +#35802 = LINE ( 'NONE', #42442, #76782 ) ; +#35803 = ORIENTED_EDGE ( 'NONE', *, *, #100750, .F. ) ; +#35804 = SURFACE_STYLE_USAGE ( .BOTH. , #90900 ) ; +#35805 = ORIENTED_EDGE ( 'NONE', *, *, #53291, .T. ) ; +#35806 = VECTOR ( 'NONE', #16484, 1000.000000000000000 ) ; +#35807 = CARTESIAN_POINT ( 'NONE', ( -0.3092775381631849840, -1.357596283920579960, 0.8299999999999999600 ) ) ; +#35808 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#35811 = LINE ( 'NONE', #72561, #45826 ) ; +#35810 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1500000000000000500 ) ) ; +#35809 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32514 ) ) ; +#35812 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35813 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35814 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94423 ), #47136 ) ; +#35815 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35816 = SURFACE_SIDE_STYLE ('',( #74600 ) ) ; +#35817 = STYLED_ITEM ( 'NONE', ( #72367 ), #6194 ) ; +#35818 = SURFACE_SIDE_STYLE ('',( #27653 ) ) ; +#35819 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58569 ) ) ; +#35820 = FILL_AREA_STYLE ('',( #91902 ) ) ; +#35821 = SURFACE_SIDE_STYLE ('',( #88402 ) ) ; +#35822 = EDGE_CURVE ( 'NONE', #66469, #28843, #2661, .T. ) ; +#35823 = ORIENTED_EDGE ( 'NONE', *, *, #8177, .T. ) ; +#35824 = CIRCLE ( 'NONE', #9687, 0.009999999999999998473 ) ; +#35825 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#35826 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#35827 = SURFACE_SIDE_STYLE ('',( #89911 ) ) ; +#35828 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79838 ) ) ; +#35829 = ORIENTED_EDGE ( 'NONE', *, *, #35249, .F. ) ; +#35830 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8100000000000000533 ) ) ; +#35831 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#35832 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#35833 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980549, 0.000000000000000000 ) ) ; +#35834 = ADVANCED_FACE ( 'NONE', ( #41467 ), #11717, .T. ) ; +#35835 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#35836 = PLANE ( 'NONE', #3000 ) ; +#35837 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#35838 = FILL_AREA_STYLE ('',( #51662 ) ) ; +#35839 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.099999999999999867, 0.1829999999999829818 ) ) ; +#35840 = DIRECTION ( 'NONE', ( 0.3631942952377797407, 0.000000000000000000, -0.9317134237021234000 ) ) ; +#35841 = SURFACE_STYLE_FILL_AREA ( #96559 ) ; +#35842 = ORIENTED_EDGE ( 'NONE', *, *, #282, .T. ) ; +#35843 = ORIENTED_EDGE ( 'NONE', *, *, #41295, .F. ) ; +#35844 = LINE ( 'NONE', #81313, #53611 ) ; +#35845 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16649, 'distance_accuracy_value', 'NONE'); +#35846 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55910, 'distance_accuracy_value', 'NONE'); +#35847 = AXIS2_PLACEMENT_3D ( 'NONE', #27424, #91685, #59096 ) ; +#35848 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#35849 = PRESENTATION_STYLE_ASSIGNMENT (( #90434 ) ) ; +#35850 = CARTESIAN_POINT ( 'NONE', ( 0.9399999999999999467, 6.470518565393449602E-18, -0.8499999999999999778 ) ) ; +#35851 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, 0.000000000000000000 ) ) ; +#35852 = LINE ( 'NONE', #66961, #8031 ) ; +#35853 = ORIENTED_EDGE ( 'NONE', *, *, #5720, .F. ) ; +#35854 = SURFACE_STYLE_USAGE ( .BOTH. , #89456 ) ; +#35855 = EDGE_LOOP ( 'NONE', ( #16916, #2207, #70139, #14685 ) ) ; +#35856 = FILL_AREA_STYLE ('',( #19998 ) ) ; +#35857 = VECTOR ( 'NONE', #49788, 1000.000000000000000 ) ; +#35858 = SURFACE_SIDE_STYLE ('',( #89946 ) ) ; +#35859 = ORIENTED_EDGE ( 'NONE', *, *, #87246, .F. ) ; +#35860 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35861 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35862 = VECTOR ( 'NONE', #9288, 1000.000000000000114 ) ; +#35863 = SURFACE_SIDE_STYLE ('',( #26187 ) ) ; +#35864 = PLANE ( 'NONE', #36576 ) ; +#35865 = EDGE_CURVE ( 'NONE', #22475, #45110, #74616, .T. ) ; +#35866 = ORIENTED_EDGE ( 'NONE', *, *, #56427, .F. ) ; +#35867 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35868 = LINE ( 'NONE', #98535, #31024 ) ; +#35869 = VECTOR ( 'NONE', #99637, 1000.000000000000000 ) ; +#35871 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35870 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68689 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15300, #86811, #62335 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35872 = ORIENTED_EDGE ( 'NONE', *, *, #95714, .F. ) ; +#35873 = VECTOR ( 'NONE', #64020, 1000.000000000000000 ) ; +#35874 = VECTOR ( 'NONE', #51146, 1000.000000000000000 ) ; +#35875 = CARTESIAN_POINT ( 'NONE', ( -1.566666666666666652, 3.500000000000000000, 0.000000000000000000 ) ) ; +#35876 = VERTEX_POINT ( 'NONE', #35833 ) ; +#35877 = ORIENTED_EDGE ( 'NONE', *, *, #63364, .F. ) ; +#35878 = SURFACE_STYLE_USAGE ( .BOTH. , #91479 ) ; +#35879 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#35880 = CARTESIAN_POINT ( 'NONE', ( -0.5047968834700360397, -1.178195226781280081, 0.8100000000000000533 ) ) ; +#35881 = STYLED_ITEM ( 'NONE', ( #44426 ), #80667 ) ; +#35882 = PLANE ( 'NONE', #84518 ) ; +#35883 = PRESENTATION_STYLE_ASSIGNMENT (( #22032 ) ) ; +#35884 = ORIENTED_EDGE ( 'NONE', *, *, #49450, .F. ) ; +#35885 = ORIENTED_EDGE ( 'NONE', *, *, #62098, .T. ) ; +#35886 = ORIENTED_EDGE ( 'NONE', *, *, #32570, .F. ) ; +#35887 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, 0.1400000000000000411 ) ) ; +#35888 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35889 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35890 = AXIS2_PLACEMENT_3D ( 'NONE', #23454, #82850, #85212 ) ; +#35892 = ORIENTED_EDGE ( 'NONE', *, *, #23697, .T. ) ; +#35891 = PLANE ( 'NONE', #73814 ) ; +#35893 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35846 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55910, #46688, #87035 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#35894 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#35895 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35896 = ORIENTED_EDGE ( 'NONE', *, *, #87805, .F. ) ; +#35897 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, -3.500000000000000444, 0.000000000000000000 ) ) ; +#35898 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35899 = ORIENTED_EDGE ( 'NONE', *, *, #47326, .T. ) ; +#35900 = EDGE_CURVE ( 'NONE', #56959, #100360, #66440, .T. ) ; +#35901 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.004999999999999999237, -0.2400000000000000189 ) ) ; +#35902 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#35903 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35904 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37496 ), #60327 ) ; +#35905 = FILL_AREA_STYLE ('',( #82358 ) ) ; +#35906 = AXIS2_PLACEMENT_3D ( 'NONE', #42949, #11219, #88924 ) ; +#35907 = CARTESIAN_POINT ( 'NONE', ( 1.800644492816920295, -1.399205570841099977, 0.8299999999999999600 ) ) ; +#35909 = CARTESIAN_POINT ( 'NONE', ( 1.498514669629020135, -1.357596283920579960, 0.8100000000000000533 ) ) ; +#35908 = LINE ( 'NONE', #59910, #51310 ) ; +#35910 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999990319, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#35911 = ORIENTED_EDGE ( 'NONE', *, *, #72564, .F. ) ; +#35912 = EDGE_CURVE ( 'NONE', #23149, #27714, #27666, .T. ) ; +#35913 = VECTOR ( 'NONE', #65092, 1000.000000000000000 ) ; +#35914 = PRESENTATION_STYLE_ASSIGNMENT (( #89019 ) ) ; +#35915 = FILL_AREA_STYLE ('',( #20558 ) ) ; +#35916 = EDGE_CURVE ( 'NONE', #13932, #98291, #19969, .T. ) ; +#35918 = SURFACE_STYLE_USAGE ( .BOTH. , #42560 ) ; +#35917 = CARTESIAN_POINT ( 'NONE', ( 0.4084453376902120181, -0.9740784349584099555, 0.8100000000000000533 ) ) ; +#35919 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35920 = LINE ( 'NONE', #59424, #53265 ) ; +#35921 = VECTOR ( 'NONE', #5635, 1000.000000000000000 ) ; +#35922 = SURFACE_SIDE_STYLE ('',( #76700 ) ) ; +#35923 = VERTEX_POINT ( 'NONE', #17934 ) ; +#35924 = EDGE_CURVE ( 'NONE', #14566, #1613, #80275, .T. ) ; +#35925 = LINE ( 'NONE', #36419, #11940 ) ; +#35926 = ADVANCED_FACE ( 'NONE', ( #83776 ), #82769, .T. ) ; +#35927 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39175 ), #50731 ) ; +#35928 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#35929 = ORIENTED_EDGE ( 'NONE', *, *, #45567, .F. ) ; +#35930 = STYLED_ITEM ( 'NONE', ( #14763 ), #95035 ) ; +#35931 = LINE ( 'NONE', #43058, #13892 ) ; +#35933 = SURFACE_SIDE_STYLE ('',( #81407 ) ) ; +#35932 = SURFACE_SIDE_STYLE ('',( #11331 ) ) ; +#35934 = CARTESIAN_POINT ( 'NONE', ( 1.655510330387720330, -0.9679977428869780409, 0.8299999999999999600 ) ) ; +#35935 = STYLED_ITEM ( 'NONE', ( #78558 ), #57571 ) ; +#35936 = FILL_AREA_STYLE ('',( #52752 ) ) ; +#35937 = EDGE_CURVE ( 'NONE', #54357, #74640, #7072, .T. ) ; +#35939 = EDGE_CURVE ( 'NONE', #38257, #44212, #14269, .T. ) ; +#35938 = LINE ( 'NONE', #35448, #25217 ) ; +#35940 = VECTOR ( 'NONE', #76145, 1000.000000000000114 ) ; +#35941 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#35942 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53841 ) ) ; +#35943 = ORIENTED_EDGE ( 'NONE', *, *, #21506, .T. ) ; +#35944 = SURFACE_STYLE_FILL_AREA ( #36434 ) ; +#35945 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#35946 = CARTESIAN_POINT ( 'NONE', ( 1.190985675097830265, -0.8845231535185279492, 0.8299999999999994049 ) ) ; +#35947 = ADVANCED_FACE ( 'NONE', ( #52149 ), #20466, .T. ) ; +#35948 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01500000000000000118, -0.2500000000000000000 ) ) ; +#35949 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#35950 = AXIS2_PLACEMENT_3D ( 'NONE', #27031, #34700, #17821 ) ; +#35951 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#35952 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.4600000000000000200, 1.250000000000000000 ) ) ; +#35953 = LINE ( 'NONE', #68551, #20271 ) ; +#35954 = EDGE_CURVE ( 'NONE', #54575, #72320, #20984, .T. ) ; +#35955 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87915, 'distance_accuracy_value', 'NONE'); +#35956 = LINE ( 'NONE', #4285, #14234 ) ; +#35957 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12969 ) ) ; +#35958 = PLANE ( 'NONE', #55278 ) ; +#35959 = STYLED_ITEM ( 'NONE', ( #91650 ), #1801 ) ; +#35960 = ORIENTED_EDGE ( 'NONE', *, *, #68955, .T. ) ; +#35961 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#35962 = ORIENTED_EDGE ( 'NONE', *, *, #8516, .F. ) ; +#35963 = PRESENTATION_STYLE_ASSIGNMENT (( #63714 ) ) ; +#35965 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99162, 'distance_accuracy_value', 'NONE'); +#35964 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53864 ), #14675 ) ; +#35966 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55538, 'distance_accuracy_value', 'NONE'); +#35967 = SURFACE_SIDE_STYLE ('',( #67072 ) ) ; +#35968 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.4866665961967886478, 0.6665916412585001227 ) ) ; +#35969 = FACE_OUTER_BOUND ( 'NONE', #29424, .T. ) ; +#35970 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#35971 = SURFACE_STYLE_FILL_AREA ( #27815 ) ; +#35972 = CARTESIAN_POINT ( 'NONE', ( 1.767907037466160070, -0.9096959278232360502, 0.8299999999999999600 ) ) ; +#35973 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608509942, 0.7099999999999999645, 0.4397321428571430157 ) ) ; +#35974 = LINE ( 'NONE', #5759, #48893 ) ; +#35975 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#35976 = ORIENTED_EDGE ( 'NONE', *, *, #67503, .F. ) ; +#35977 = CARTESIAN_POINT ( 'NONE', ( 1.055898260968923363, -1.386462394657160369, 0.8099999999997468114 ) ) ; +#35978 = FILL_AREA_STYLE ('',( #20613 ) ) ; +#35979 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62658, 'distance_accuracy_value', 'NONE'); +#35980 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#35981 = VECTOR ( 'NONE', #42224, 1000.000000000000114 ) ; +#35982 = VERTEX_POINT ( 'NONE', #67429 ) ; +#35983 = LINE ( 'NONE', #29781, #49457 ) ; +#35984 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#35985 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#35986 = CARTESIAN_POINT ( 'NONE', ( -1.309030937367239966, -1.351519064127929992, 0.8100000000000000533 ) ) ; +#35987 = EDGE_CURVE ( 'NONE', #31005, #15336, #67913, .T. ) ; +#35988 = ORIENTED_EDGE ( 'NONE', *, *, #92495, .F. ) ; +#35989 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35990 = STYLED_ITEM ( 'NONE', ( #89830 ), #44861 ) ; +#35991 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59446, 'distance_accuracy_value', 'NONE'); +#35992 = FILL_AREA_STYLE_COLOUR ( '', #36458 ) ; +#35993 = FILL_AREA_STYLE_COLOUR ( '', #37712 ) ; +#35994 = EDGE_CURVE ( 'NONE', #17269, #11053, #5615, .T. ) ; +#35995 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.000000000000000000 ) ) ; +#35996 = ORIENTED_EDGE ( 'NONE', *, *, #80195, .F. ) ; +#35997 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#35998 = VECTOR ( 'NONE', #86564, 1000.000000000000000 ) ; +#35999 = SURFACE_SIDE_STYLE ('',( #80445 ) ) ; +#36000 = CARTESIAN_POINT ( 'NONE', ( 9.924579124874954417, 8.109696875125045779, 0.8991599999999999593 ) ) ; +#36001 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#36002 = VERTEX_POINT ( 'NONE', #2922 ) ; +#36003 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#36004 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #69899, #15768 ), + ( #37299, #92377 ), + ( #46920, #16260 ), + ( #55137, #29601 ), + ( #464, #8039 ), + ( #30577, #53108 ), + ( #84242, #45392 ), + ( #45891, #53606 ), + ( #84728, #14745 ), + ( #77076, #7039 ), + ( #61786, #71438 ), + ( #17791, #82004 ), + ( #87249, #25004 ), + ( #27890, #25500 ), + ( #41323, #33140 ), + ( #35551, #24507 ), + ( #43167, #48480 ), + ( #79109, #40311 ), + ( #32647, #33663 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06067316132421259750, 0.1174012791737849976, 0.1721114849999169916, 0.2239540598056740106, 0.2751712599520699798, 0.3269093728512980079, 0.3800758009271369975, 0.4347860067532690054, 0.4913729683531249948, 0.5518286346082740268, 0.6156071820398010264, 0.6833212327671399633, 0.7548858889968480534, 0.8318279483092090310, 0.9132179767459820408, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36005 = VECTOR ( 'NONE', #70144, 1000.000000000000000 ) ; +#36006 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97552 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45791, #36572, #37570 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36007 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24331 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84593, #61649, #79478 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36008 = EDGE_LOOP ( 'NONE', ( #3457, #4976, #59885, #76493 ) ) ; +#36011 = ORIENTED_EDGE ( 'NONE', *, *, #90982, .F. ) ; +#36010 = LINE ( 'NONE', #13417, #73669 ) ; +#36009 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8363 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79178, #47012, #70486 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36012 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52331 ) ) ; +#36014 = SURFACE_SIDE_STYLE ('',( #68102 ) ) ; +#36013 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#36015 = LINE ( 'NONE', #81487, #35046 ) ; +#36016 = VECTOR ( 'NONE', #87831, 1000.000000000000000 ) ; +#36017 = FILL_AREA_STYLE_COLOUR ( '', #70000 ) ; +#36018 = VERTEX_POINT ( 'NONE', #23508 ) ; +#36019 = VECTOR ( 'NONE', #39623, 1000.000000000000000 ) ; +#36020 = LINE ( 'NONE', #66138, #52919 ) ; +#36021 = ORIENTED_EDGE ( 'NONE', *, *, #11154, .T. ) ; +#36023 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36022 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#36024 = ORIENTED_EDGE ( 'NONE', *, *, #10591, .T. ) ; +#36025 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82553, #50924, #13012, #67208 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36027 = PLANE ( 'NONE', #61432 ) ; +#36026 = CARTESIAN_POINT ( 'NONE', ( 0.1702531576982217187, -1.398942686622796749, 0.8100000000000001643 ) ) ; +#36028 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53263 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96776, #58050, #40188 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36029 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36030 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36031 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.383333333333333304, 0.000000000000000000 ) ) ; +#36032 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9829 ), #96327 ) ; +#36033 = SURFACE_STYLE_FILL_AREA ( #58533 ) ; +#36034 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#36035 = VERTEX_POINT ( 'NONE', #92885 ) ; +#36036 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999998002, 0.6700000000000000400, -0.2000000000000000111 ) ) ; +#36037 = ORIENTED_EDGE ( 'NONE', *, *, #70613, .F. ) ; +#36038 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, -0.1350000000000000089 ) ) ; +#36040 = PLANE ( 'NONE', #62091 ) ; +#36039 = FILL_AREA_STYLE_COLOUR ( '', #42883 ) ; +#36041 = STYLED_ITEM ( 'NONE', ( #40080 ), #51571 ) ; +#36042 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#36043 = FILL_AREA_STYLE ('',( #30328 ) ) ; +#36044 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#36045 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6775 ), #55660 ) ; +#36047 = SURFACE_STYLE_FILL_AREA ( #74825 ) ; +#36046 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36048 = PRESENTATION_STYLE_ASSIGNMENT (( #89652 ) ) ; +#36049 = ORIENTED_EDGE ( 'NONE', *, *, #22913, .F. ) ; +#36050 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#36052 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8648700000000000276 ) ) ; +#36051 = LINE ( 'NONE', #4865, #69119 ) ; +#36053 = AXIS2_PLACEMENT_3D ( 'NONE', #17, #61842, #38847 ) ; +#36054 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999223, 0.2399999999999999911 ) ) ; +#36056 = EDGE_CURVE ( 'NONE', #86631, #72010, #15808, .T. ) ; +#36055 = LINE ( 'NONE', #5347, #13581 ) ; +#36057 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.7099999999999999645, 0.8000000000000001554 ) ) ; +#36058 = SURFACE_STYLE_USAGE ( .BOTH. , #59574 ) ; +#36059 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36060 = ORIENTED_EDGE ( 'NONE', *, *, #18208, .T. ) ; +#36061 = SURFACE_SIDE_STYLE ('',( #34058 ) ) ; +#36062 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.05000000000000000278, 0.1900000000000000022 ) ) ; +#36063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36064 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2808578643762690286, 0.1434314575050761598 ) ) ; +#36065 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#36066 = FILL_AREA_STYLE_COLOUR ( '', #96841 ) ; +#36067 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36068 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#36069 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#36070 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#36071 = SURFACE_SIDE_STYLE ('',( #42709 ) ) ; +#36072 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5400 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65270, #7655, #57664 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36073 = EDGE_CURVE ( 'NONE', #46536, #100419, #2152, .T. ) ; +#36074 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36075 = AXIS2_PLACEMENT_3D ( 'NONE', #56435, #19084, #72219 ) ; +#36076 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#36077 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#36078 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36079 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36080 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36081 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26239 ) ) ; +#36082 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72629, 'distance_accuracy_value', 'NONE'); +#36083 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16480 ), #11555 ) ; +#36084 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.000000000000000000 ) ) ; +#36085 = LINE ( 'NONE', #17836, #47055 ) ; +#36086 = LINE ( 'NONE', #4891, #51994 ) ; +#36087 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36088 = CARTESIAN_POINT ( 'NONE', ( -0.9121606455498090238, -1.316410597191429943, 0.8299999999999999600 ) ) ; +#36089 = EDGE_LOOP ( 'NONE', ( #77965, #7970, #88154, #50958 ) ) ; +#36090 = FILL_AREA_STYLE ('',( #45194 ) ) ; +#36091 = VECTOR ( 'NONE', #93570, 1000.000000000000000 ) ; +#36092 = LINE ( 'NONE', #12497, #20833 ) ; +#36093 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39843, 'distance_accuracy_value', 'NONE'); +#36094 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19916, 'distance_accuracy_value', 'NONE'); +#36096 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#36095 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#36097 = VECTOR ( 'NONE', #48528, 1000.000000000000000 ) ; +#36098 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80123 ) ) ; +#36099 = CARTESIAN_POINT ( 'NONE', ( -0.02448719543550549951, -1.001398657004090254, 0.8300000000000002931 ) ) ; +#36100 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 8.675382000000000815, 0.8648700000000000276 ) ) ; +#36101 = FACE_OUTER_BOUND ( 'NONE', #21026, .T. ) ; +#36102 = ADVANCED_FACE ( 'NONE', ( #499 ), #77612, .T. ) ; +#36103 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36104 = ORIENTED_EDGE ( 'NONE', *, *, #21840, .F. ) ; +#36105 = VECTOR ( 'NONE', #2948, 1000.000000000000000 ) ; +#36106 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#36107 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36108 = EDGE_LOOP ( 'NONE', ( #46664, #48573, #91812, #10399 ) ) ; +#36109 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999689, 2.000000000000000000, 0.000000000000000000 ) ) ; +#36110 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75005, 'distance_accuracy_value', 'NONE'); +#36111 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7502, #39229, #32094, #62245 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36112 = EDGE_CURVE ( 'NONE', #2733, #34253, #73373, .T. ) ; +#36113 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, -0.1444665087776849932, 0.5862888163215710380 ) ) ; +#36114 = EDGE_LOOP ( 'NONE', ( #82296, #61852, #1140, #78294 ) ) ; +#36115 = VERTEX_POINT ( 'NONE', #46962 ) ; +#36116 = FILL_AREA_STYLE ('',( #50936 ) ) ; +#36117 = VERTEX_POINT ( 'NONE', #7575 ) ; +#36119 = CARTESIAN_POINT ( 'NONE', ( 0.2667602038132769748, -1.009329072279059991, 0.8299999999999996270 ) ) ; +#36118 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27960 ), #37704 ) ; +#36120 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36121 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.699999999999999734, 0.000000000000000000 ) ) ; +#36122 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36123 = CARTESIAN_POINT ( 'NONE', ( -1.235751819672409990, -0.8946064028769500354, 0.8299999999999997380 ) ) ; +#36124 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8648700000000000276 ) ) ; +#36126 = ORIENTED_EDGE ( 'NONE', *, *, #58139, .T. ) ; +#36125 = VERTEX_POINT ( 'NONE', #8076 ) ; +#36127 = AXIS2_PLACEMENT_3D ( 'NONE', #11886, #12400, #73286 ) ; +#36128 = ORIENTED_EDGE ( 'NONE', *, *, #39504, .F. ) ; +#36129 = ORIENTED_EDGE ( 'NONE', *, *, #89488, .F. ) ; +#36130 = PLANE ( 'NONE', #99609 ) ; +#36131 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36132 = PLANE ( 'NONE', #22962 ) ; +#36134 = LINE ( 'NONE', #99777, #69155 ) ; +#36133 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.2000000000000000111, -13.54999999999999893 ) ) ; +#36135 = ADVANCED_FACE ( 'NONE', ( #38816 ), #41726, .F. ) ; +#36136 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36137 = AXIS2_PLACEMENT_3D ( 'NONE', #81205, #64854, #1052 ) ; +#36138 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36139 = ORIENTED_EDGE ( 'NONE', *, *, #38144, .T. ) ; +#36140 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #52221, #67002, #97121, #43016 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36142 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#36141 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#36143 = EDGE_CURVE ( 'NONE', #52193, #60497, #25308, .T. ) ; +#36144 = ORIENTED_EDGE ( 'NONE', *, *, #2613, .T. ) ; +#36145 = ORIENTED_EDGE ( 'NONE', *, *, #27518, .F. ) ; +#36146 = CARTESIAN_POINT ( 'NONE', ( 0.9822218282947740020, -1.079235908285120171, 0.8299999999999999600 ) ) ; +#36148 = LINE ( 'NONE', #22297, #72708 ) ; +#36147 = FILL_AREA_STYLE_COLOUR ( '', #36432 ) ; +#36149 = PRESENTATION_STYLE_ASSIGNMENT (( #90239 ) ) ; +#36150 = ORIENTED_EDGE ( 'NONE', *, *, #10262, .T. ) ; +#36151 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#36152 = SURFACE_STYLE_FILL_AREA ( #15100 ) ; +#36153 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36154 = FILL_AREA_STYLE ('',( #88751 ) ) ; +#36155 = ORIENTED_EDGE ( 'NONE', *, *, #27171, .T. ) ; +#36157 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#36156 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#36158 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36159 = EDGE_LOOP ( 'NONE', ( #87337, #33106, #88315, #49709 ) ) ; +#36160 = ORIENTED_EDGE ( 'NONE', *, *, #61450, .F. ) ; +#36161 = EDGE_CURVE ( 'NONE', #1291, #4125, #26411, .T. ) ; +#36163 = CARTESIAN_POINT ( 'NONE', ( 1.150000000000000133, 0.7099999999999999645, 1.079289321881345076 ) ) ; +#36162 = CARTESIAN_POINT ( 'NONE', ( 0.4157215867521200092, -0.9061895606545929960, 0.8299999999999992939 ) ) ; +#36164 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73603 ) ) ; +#36166 = EDGE_CURVE ( 'NONE', #78426, #41349, #89188, .T. ) ; +#36167 = SURFACE_STYLE_FILL_AREA ( #43793 ) ; +#36168 = SURFACE_SIDE_STYLE ('',( #60171 ) ) ; +#36169 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1968 ), #93164 ) ; +#36170 = SURFACE_STYLE_USAGE ( .BOTH. , #5942 ) ; +#36171 = FACE_OUTER_BOUND ( 'NONE', #8514, .T. ) ; +#36172 = LINE ( 'NONE', #14621, #60793 ) ; +#36173 = FACE_OUTER_BOUND ( 'NONE', #57213, .T. ) ; +#36174 = ORIENTED_EDGE ( 'NONE', *, *, #48014, .T. ) ; +#36175 = CARTESIAN_POINT ( 'NONE', ( 4.397642065455404925, 1.598204329023803272, -11.91999999999999993 ) ) ; +#36176 = VERTEX_POINT ( 'NONE', #3432 ) ; +#36177 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36178 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36179 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36180 = CARTESIAN_POINT ( 'NONE', ( 1.441086107696939900, -1.316410597191429943, 0.8299999999999999600 ) ) ; +#36182 = EDGE_CURVE ( 'NONE', #10244, #89436, #82616, .T. ) ; +#36181 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36183 = SURFACE_STYLE_FILL_AREA ( #99824 ) ; +#36184 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36185 = VERTEX_POINT ( 'NONE', #89686 ) ; +#36186 = SURFACE_STYLE_USAGE ( .BOTH. , #20842 ) ; +#36187 = CARTESIAN_POINT ( 'NONE', ( 0.1711848682203470362, -1.102962211187280106, 0.8299999999999999600 ) ) ; +#36188 = FACE_OUTER_BOUND ( 'NONE', #33882, .T. ) ; +#36189 = PRESENTATION_STYLE_ASSIGNMENT (( #20844 ) ) ; +#36190 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91611 ) ) ; +#36191 = FILL_AREA_STYLE_COLOUR ( '', #14721 ) ; +#36192 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36193 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#36194 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86466, #56374, #38124 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36195 = LINE ( 'NONE', #68788, #30786 ) ; +#36196 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89067 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79812, #24190, #162 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36197 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#36198 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98153, 'distance_accuracy_value', 'NONE'); +#36199 = ORIENTED_EDGE ( 'NONE', *, *, #59126, .T. ) ; +#36200 = CARTESIAN_POINT ( 'NONE', ( -1.315307816756859260, -1.349629322163891532, 0.8099999999997303801 ) ) ; +#36201 = ORIENTED_EDGE ( 'NONE', *, *, #22821, .F. ) ; +#36202 = LINE ( 'NONE', #19862, #40105 ) ; +#36203 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#36204 = STYLED_ITEM ( 'NONE', ( #73838 ), #18506 ) ; +#36205 = EDGE_CURVE ( 'NONE', #87351, #2319, #27408, .T. ) ; +#36206 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.6999999999999999556, -13.40000000000000036 ) ) ; +#36207 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 3.570070999999999994, 0.8648700000000000276 ) ) ; +#36208 = STYLED_ITEM ( 'NONE', ( #34821 ), #43150 ) ; +#36209 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36210 = FILL_AREA_STYLE_COLOUR ( '', #69452 ) ; +#36211 = EDGE_CURVE ( 'NONE', #69070, #56085, #28895, .T. ) ; +#36212 = ORIENTED_EDGE ( 'NONE', *, *, #46545, .T. ) ; +#36213 = ORIENTED_EDGE ( 'NONE', *, *, #59482, .F. ) ; +#36214 = FILL_AREA_STYLE_COLOUR ( '', #71616 ) ; +#36215 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50871 ) ) ; +#36216 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36217 = PRESENTATION_STYLE_ASSIGNMENT (( #75019 ) ) ; +#36218 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15279 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70161, #70673, #1227 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36219 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36220 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98321, 'distance_accuracy_value', 'NONE'); +#36221 = FILL_AREA_STYLE ('',( #5996 ) ) ; +#36222 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36223 = STYLED_ITEM ( 'NONE', ( #8383 ), #10977 ) ; +#36224 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51297, 'distance_accuracy_value', 'NONE'); +#36225 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36226 = EDGE_CURVE ( 'NONE', #58149, #73120, #82539, .T. ) ; +#36227 = VECTOR ( 'NONE', #57265, 1000.000000000000000 ) ; +#36228 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, 0.1458578643762690752 ) ) ; +#36229 = ORIENTED_EDGE ( 'NONE', *, *, #66950, .F. ) ; +#36230 = ORIENTED_EDGE ( 'NONE', *, *, #33757, .T. ) ; +#36231 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44710, 'distance_accuracy_value', 'NONE'); +#36232 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36233 = VERTEX_POINT ( 'NONE', #34585 ) ; +#36234 = PLANE ( 'NONE', #83785 ) ; +#36235 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#36236 = LINE ( 'NONE', #35744, #18946 ) ; +#36237 = SURFACE_SIDE_STYLE ('',( #5037 ) ) ; +#36238 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36239 = CARTESIAN_POINT ( 'NONE', ( -0.3663668861142549971, -1.072315624320830274, 0.8100000000000000533 ) ) ; +#36240 = CARTESIAN_POINT ( 'NONE', ( -0.4564179441963438499, 1.285539895947890754, 0.8100000000000001643 ) ) ; +#36241 = SURFACE_STYLE_FILL_AREA ( #82205 ) ; +#36243 = ORIENTED_EDGE ( 'NONE', *, *, #92971, .F. ) ; +#36242 = ORIENTED_EDGE ( 'NONE', *, *, #16559, .F. ) ; +#36244 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36245 = ORIENTED_EDGE ( 'NONE', *, *, #99950, .F. ) ; +#36246 = CARTESIAN_POINT ( 'NONE', ( 1.540061115671039982, -0.9808836469697840288, 0.8099999999999981659 ) ) ; +#36247 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#36248 = ORIENTED_EDGE ( 'NONE', *, *, #88442, .T. ) ; +#36249 = STYLED_ITEM ( 'NONE', ( #46073 ), #52644 ) ; +#36250 = ORIENTED_EDGE ( 'NONE', *, *, #19713, .T. ) ; +#36251 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36252 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#36253 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75371 ) ) ; +#36254 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#36256 = SURFACE_STYLE_USAGE ( .BOTH. , #91852 ) ; +#36255 = LINE ( 'NONE', #20917, #10540 ) ; +#36257 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36258 = EDGE_LOOP ( 'NONE', ( #71043, #9256, #72128, #53673 ) ) ; +#36259 = ORIENTED_EDGE ( 'NONE', *, *, #28825, .F. ) ; +#36260 = PRESENTATION_STYLE_ASSIGNMENT (( #11654 ) ) ; +#36262 = EDGE_CURVE ( 'NONE', #86420, #9772, #74866, .T. ) ; +#36261 = STYLED_ITEM ( 'NONE', ( #50093 ), #46867 ) ; +#36263 = VERTEX_POINT ( 'NONE', #19213 ) ; +#36264 = ADVANCED_FACE ( 'NONE', ( #60088 ), #11986, .T. ) ; +#36265 = FILL_AREA_STYLE ('',( #70252 ) ) ; +#36266 = FACE_OUTER_BOUND ( 'NONE', #43338, .T. ) ; +#36267 = AXIS2_PLACEMENT_3D ( 'NONE', #98797, #11527, #20772 ) ; +#36268 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56447 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22019, #52194, #29194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36270 = ORIENTED_EDGE ( 'NONE', *, *, #15962, .T. ) ; +#36269 = DIRECTION ( 'NONE', ( 0.7071090539100457484, 0.7071045084557444627, 0.000000000000000000 ) ) ; +#36271 = LINE ( 'NONE', #98448, #27017 ) ; +#36272 = LINE ( 'NONE', #65371, #100923 ) ; +#36273 = ORIENTED_EDGE ( 'NONE', *, *, #60597, .T. ) ; +#36274 = CARTESIAN_POINT ( 'NONE', ( 0.01352834099273039943, -1.306448053922619978, 0.8100000000000000533 ) ) ; +#36275 = VERTEX_POINT ( 'NONE', #84521 ) ; +#36276 = ORIENTED_EDGE ( 'NONE', *, *, #12163, .T. ) ; +#36277 = EDGE_CURVE ( 'NONE', #43386, #89489, #20039, .T. ) ; +#36278 = FILL_AREA_STYLE ('',( #89378 ) ) ; +#36279 = EDGE_CURVE ( 'NONE', #26125, #31304, #86035, .T. ) ; +#36280 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36281 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8648700000000000276 ) ) ; +#36282 = EDGE_CURVE ( 'NONE', #27455, #64904, #6909, .T. ) ; +#36283 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36284 = STYLED_ITEM ( 'NONE', ( #32772 ), #87283 ) ; +#36285 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#36286 = SURFACE_SIDE_STYLE ('',( #66896 ) ) ; +#36287 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18228 ), #98139 ) ; +#36288 = PLANE ( 'NONE', #78470 ) ; +#36289 = ORIENTED_EDGE ( 'NONE', *, *, #86260, .T. ) ; +#36290 = FILL_AREA_STYLE ('',( #59299 ) ) ; +#36291 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36292 = ORIENTED_EDGE ( 'NONE', *, *, #100880, .T. ) ; +#36293 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29699 ), #10079 ) ; +#36295 = EDGE_CURVE ( 'NONE', #9760, #83206, #99262, .T. ) ; +#36294 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.500000000000000222, 0.1829999999999870064 ) ) ; +#36296 = STYLED_ITEM ( 'NONE', ( #92096 ), #11181 ) ; +#36297 = SURFACE_STYLE_FILL_AREA ( #28612 ) ; +#36299 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000311, 0.000000000000000000 ) ) ; +#36298 = SURFACE_STYLE_USAGE ( .BOTH. , #6571 ) ; +#36300 = SURFACE_STYLE_FILL_AREA ( #5099 ) ; +#36301 = PRESENTATION_STYLE_ASSIGNMENT (( #13218 ) ) ; +#36302 = ADVANCED_FACE ( 'NONE', ( #6825 ), #68182, .T. ) ; +#36303 = PLANE ( 'NONE', #21470 ) ; +#36304 = LINE ( 'NONE', #11204, #23557 ) ; +#36305 = EDGE_CURVE ( 'NONE', #1969, #82928, #41369, .T. ) ; +#36306 = SURFACE_SIDE_STYLE ('',( #89410 ) ) ; +#36307 = ADVANCED_FACE ( 'NONE', ( #21731 ), #58833, .F. ) ; +#36308 = STYLED_ITEM ( 'NONE', ( #3611 ), #70441 ) ; +#36309 = VECTOR ( 'NONE', #76625, 1000.000000000000000 ) ; +#36310 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53394, 'distance_accuracy_value', 'NONE'); +#36311 = ORIENTED_EDGE ( 'NONE', *, *, #47030, .F. ) ; +#36312 = FILL_AREA_STYLE ('',( #99486 ) ) ; +#36313 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #93897 ) ) ; +#36314 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36315 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#36316 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36317 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20043 ) ) ; +#36318 = FILL_AREA_STYLE ('',( #5120 ) ) ; +#36319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36320 = LINE ( 'NONE', #91925, #16270 ) ; +#36321 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, 0.000000000000000000 ) ) ; +#36322 = VECTOR ( 'NONE', #64753, 1000.000000000000000 ) ; +#36323 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#36324 = EDGE_CURVE ( 'NONE', #78654, #50863, #9465, .T. ) ; +#36325 = VERTEX_POINT ( 'NONE', #86549 ) ; +#36326 = SURFACE_SIDE_STYLE ('',( #20996 ) ) ; +#36327 = VERTEX_POINT ( 'NONE', #71223 ) ; +#36328 = SURFACE_SIDE_STYLE ('',( #67442 ) ) ; +#36329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62386, 'distance_accuracy_value', 'NONE'); +#36330 = PLANE ( 'NONE', #96920 ) ; +#36331 = FILL_AREA_STYLE_COLOUR ( '', #26101 ) ; +#36332 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#36333 = STYLED_ITEM ( 'NONE', ( #69253 ), #19319 ) ; +#36334 = FACE_OUTER_BOUND ( 'NONE', #98208, .T. ) ; +#36335 = AXIS2_PLACEMENT_3D ( 'NONE', #15925, #38936, #93516 ) ; +#36336 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36337 = CARTESIAN_POINT ( 'NONE', ( -0.8073670843789639839, 0.5792268695032709580, 0.8100000000000000533 ) ) ; +#36338 = ORIENTED_EDGE ( 'NONE', *, *, #85129, .T. ) ; +#36339 = EDGE_CURVE ( 'NONE', #50837, #15816, #41608, .T. ) ; +#36340 = PRESENTATION_STYLE_ASSIGNMENT (( #12770 ) ) ; +#36341 = LINE ( 'NONE', #60840, #71644 ) ; +#36342 = SURFACE_STYLE_FILL_AREA ( #5143 ) ; +#36343 = ORIENTED_EDGE ( 'NONE', *, *, #8029, .T. ) ; +#36344 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27504 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58317, #42465, #65944 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36345 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36346 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#36347 = ORIENTED_EDGE ( 'NONE', *, *, #11344, .T. ) ; +#36348 = EDGE_CURVE ( 'NONE', #43496, #5131, #55932, .T. ) ; +#36349 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36350 = SURFACE_STYLE_USAGE ( .BOTH. , #13266 ) ; +#36351 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36352 = SURFACE_STYLE_FILL_AREA ( #29186 ) ; +#36353 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36354 = ADVANCED_FACE ( 'NONE', ( #16566 ), #87056, .F. ) ; +#36355 = ORIENTED_EDGE ( 'NONE', *, *, #13909, .T. ) ; +#36356 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36357 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6019, #5544, #74550, #5046, #67355, #36737, #59765, #59253, #60729, #91834, #82695, #36246, #52564, #44852, #52073, #67842, #98922, #83704, #76031 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.178056893902119485E-05, 4.225456704309851698E-05, 6.194886443256553729E-05, 8.074241141082066074E-05, 9.889914185196789194E-05, 0.0001164500649587962882, 0.0001336937882700164762, 0.0001506401837167742775, 0.0001676736896390550288, 0.0001849013668277523479, 0.0002027830705271023329, 0.0002211741807831157794, 0.0002402048697158812014, 0.0002597008077081194876, 0.0002800873636358653870, 0.0003011686205146952774 ), + .UNSPECIFIED. ) ; +#36358 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36359 = VERTEX_POINT ( 'NONE', #5251 ) ; +#36360 = FILL_AREA_STYLE ('',( #36861 ) ) ; +#36361 = AXIS2_PLACEMENT_3D ( 'NONE', #42033, #21924, #36757 ) ; +#36362 = FILL_AREA_STYLE ('',( #5160 ) ) ; +#36363 = VERTEX_POINT ( 'NONE', #50793 ) ; +#36364 = ORIENTED_EDGE ( 'NONE', *, *, #72463, .F. ) ; +#36365 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#36366 = CARTESIAN_POINT ( 'NONE', ( -0.5594799075883629680, -1.188256883098049999, 0.8100000000000000533 ) ) ; +#36367 = SURFACE_SIDE_STYLE ('',( #18509 ) ) ; +#36368 = STYLED_ITEM ( 'NONE', ( #96209 ), #67139 ) ; +#36369 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36370 = STYLED_ITEM ( 'NONE', ( #26834 ), #2687 ) ; +#36371 = ORIENTED_EDGE ( 'NONE', *, *, #92658, .T. ) ; +#36372 = VERTEX_POINT ( 'NONE', #90567 ) ; +#36373 = EDGE_CURVE ( 'NONE', #46754, #70042, #33794, .T. ) ; +#36374 = ORIENTED_EDGE ( 'NONE', *, *, #97344, .F. ) ; +#36375 = EDGE_CURVE ( 'NONE', #5892, #81719, #66575, .T. ) ; +#36376 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#36377 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3711 ) ) ; +#36379 = ORIENTED_EDGE ( 'NONE', *, *, #71061, .F. ) ; +#36378 = LINE ( 'NONE', #89980, #3633 ) ; +#36380 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36381 = FACE_OUTER_BOUND ( 'NONE', #68600, .T. ) ; +#36382 = VECTOR ( 'NONE', #56478, 1000.000000000000000 ) ; +#36383 = VERTEX_POINT ( 'NONE', #81928 ) ; +#36384 = FACE_OUTER_BOUND ( 'NONE', #91578, .T. ) ; +#36385 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#36386 = ORIENTED_EDGE ( 'NONE', *, *, #26248, .F. ) ; +#36387 = EDGE_CURVE ( 'NONE', #98110, #61605, #93490, .T. ) ; +#36388 = FACE_OUTER_BOUND ( 'NONE', #99595, .T. ) ; +#36389 = EDGE_CURVE ( 'NONE', #28287, #96599, #67424, .T. ) ; +#36390 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36391 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96070, #18480, #33839, #19994 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36392 = VECTOR ( 'NONE', #106, 1000.000000000000000 ) ; +#36393 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36394 = EDGE_CURVE ( 'NONE', #36855, #85668, #11860, .T. ) ; +#36395 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48268 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55810, #30777, #94042 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36396 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6981 ) ) ; +#36397 = CARTESIAN_POINT ( 'NONE', ( 1.731329805614240325, -1.441250752426249893, 0.8100000000000000533 ) ) ; +#36399 = CARTESIAN_POINT ( 'NONE', ( 4.670776249750026032, 3.676137249750024871, 0.8991599999999999593 ) ) ; +#36398 = SURFACE_STYLE_USAGE ( .BOTH. , #42550 ) ; +#36400 = PRESENTATION_STYLE_ASSIGNMENT (( #28717 ) ) ; +#36401 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36402 = VECTOR ( 'NONE', #65512, 1000.000000000000000 ) ; +#36403 = ORIENTED_EDGE ( 'NONE', *, *, #47749, .F. ) ; +#36404 = SURFACE_STYLE_USAGE ( .BOTH. , #90004 ) ; +#36405 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#36406 = VECTOR ( 'NONE', #94143, 1000.000000000000000 ) ; +#36407 = STYLED_ITEM ( 'NONE', ( #31155 ), #36102 ) ; +#36408 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.000000000000000000 ) ) ; +#36410 = CARTESIAN_POINT ( 'NONE', ( 1.332610324242501809, -1.410691121758092637, 0.8099999999997313793 ) ) ; +#36409 = PLANE ( 'NONE', #67420 ) ; +#36411 = VECTOR ( 'NONE', #66101, 1000.000000000000000 ) ; +#36412 = ADVANCED_FACE ( 'NONE', ( #26799 ), #4781, .T. ) ; +#36413 = AXIS2_PLACEMENT_3D ( 'NONE', #91590, #38483, #76774 ) ; +#36414 = VECTOR ( 'NONE', #93866, 1000.000000000000000 ) ; +#36415 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.05000000000000000278, 0.1900000000000000022 ) ) ; +#36416 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#36417 = ORIENTED_EDGE ( 'NONE', *, *, #63783, .F. ) ; +#36418 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#36420 = AXIS2_PLACEMENT_3D ( 'NONE', #85672, #79034, #62715 ) ; +#36419 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 9.700687000000002058, 0.8648700000000000276 ) ) ; +#36421 = ORIENTED_EDGE ( 'NONE', *, *, #100008, .F. ) ; +#36422 = ADVANCED_FACE ( 'NONE', ( #98635 ), #51778, .T. ) ; +#36423 = FILL_AREA_STYLE_COLOUR ( '', #73215 ) ; +#36424 = ADVANCED_FACE ( 'NONE', ( #49783 ), #42607, .T. ) ; +#36426 = FILL_AREA_STYLE ('',( #42073 ) ) ; +#36425 = DIRECTION ( 'NONE', ( -0.7071072811858626350, 0.7071062811868787934, 0.000000000000000000 ) ) ; +#36428 = STYLED_ITEM ( 'NONE', ( #13696 ), #59708 ) ; +#36427 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#36429 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, 0.2999999999999999889 ) ) ; +#36430 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15154 ) ) ; +#36431 = PRESENTATION_STYLE_ASSIGNMENT (( #12854 ) ) ; +#36432 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36433 = VERTEX_POINT ( 'NONE', #91559 ) ; +#36434 = FILL_AREA_STYLE ('',( #76716 ) ) ; +#36435 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36436 = SURFACE_STYLE_USAGE ( .BOTH. , #6692 ) ; +#36437 = PLANE ( 'NONE', #64931 ) ; +#36438 = FILL_AREA_STYLE_COLOUR ( '', #66409 ) ; +#36439 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.3666666666666656416, 0.000000000000000000 ) ) ; +#36440 = LINE ( 'NONE', #98620, #8329 ) ; +#36441 = FILL_AREA_STYLE ('',( #51766 ) ) ; +#36442 = CARTESIAN_POINT ( 'NONE', ( -0.5550755121431560912, 0.6567860187191519872, 0.8299999999999999600 ) ) ; +#36443 = SURFACE_STYLE_USAGE ( .BOTH. , #5234 ) ; +#36444 = SURFACE_STYLE_FILL_AREA ( #5238 ) ; +#36445 = ADVANCED_FACE ( 'NONE', ( #93025 ), #6710, .T. ) ; +#36446 = PRESENTATION_STYLE_ASSIGNMENT (( #19605 ) ) ; +#36447 = VERTEX_POINT ( 'NONE', #92537 ) ; +#36448 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#36449 = ORIENTED_EDGE ( 'NONE', *, *, #66726, .F. ) ; +#36450 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 0.4242640687119280107 ) ) ; +#36451 = FILL_AREA_STYLE_COLOUR ( '', #6294 ) ; +#36452 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.4700000000282762436, 0.6499230723708768753 ) ) ; +#36453 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#36454 = FILL_AREA_STYLE ('',( #67074 ) ) ; +#36455 = FILL_AREA_STYLE_COLOUR ( '', #1527 ) ; +#36456 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#36457 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36458 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36459 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36460 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #67938, #37354, #91452, #43477 ), + .UNSPECIFIED., .F., .T. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.3333333333333333703, 0.3333333333333333703, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#36461 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#36462 = VERTEX_POINT ( 'NONE', #99141 ) ; +#36463 = EDGE_CURVE ( 'NONE', #77680, #82464, #46017, .T. ) ; +#36464 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#36465 = PRESENTATION_STYLE_ASSIGNMENT (( #27301 ) ) ; +#36466 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#36467 = VECTOR ( 'NONE', #75826, 1000.000000000000000 ) ; +#36468 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#36469 = ORIENTED_EDGE ( 'NONE', *, *, #12098, .T. ) ; +#36470 = FILL_AREA_STYLE_COLOUR ( '', #38003 ) ; +#36471 = ADVANCED_FACE ( 'NONE', ( #70074 ), #32306, .T. ) ; +#36472 = STYLED_ITEM ( 'NONE', ( #71867 ), #47549 ) ; +#36473 = VECTOR ( 'NONE', #98529, 1000.000000000000000 ) ; +#36474 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#36475 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36476 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#36477 = SURFACE_STYLE_USAGE ( .BOTH. , #13919 ) ; +#36478 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11879 ), #38069 ) ; +#36479 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#36480 = EDGE_CURVE ( 'NONE', #72570, #75133, #1145, .T. ) ; +#36481 = ORIENTED_EDGE ( 'NONE', *, *, #7932, .T. ) ; +#36482 = LINE ( 'NONE', #76257, #33563 ) ; +#36483 = SURFACE_STYLE_USAGE ( .BOTH. , #51307 ) ; +#36484 = SURFACE_STYLE_FILL_AREA ( #91583 ) ; +#36485 = FACE_OUTER_BOUND ( 'NONE', #70079, .T. ) ; +#36486 = STYLED_ITEM ( 'NONE', ( #89549 ), #19635 ) ; +#36487 = ADVANCED_FACE ( 'NONE', ( #48649 ), #25179, .T. ) ; +#36489 = AXIS2_PLACEMENT_3D ( 'NONE', #73364, #18697, #49894 ) ; +#36488 = CARTESIAN_POINT ( 'NONE', ( 1.602494679827060065, -1.010243534007990052, 0.8099999999999994982 ) ) ; +#36490 = VERTEX_POINT ( 'NONE', #25658 ) ; +#36492 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80386 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62054, #69125, #76837 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36491 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39961 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13809, #99543, #52690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36493 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52591 ) ) ; +#36494 = PRESENTATION_STYLE_ASSIGNMENT (( #29796 ) ) ; +#36495 = LINE ( 'NONE', #35500, #4854 ) ; +#36496 = FACE_OUTER_BOUND ( 'NONE', #51611, .T. ) ; +#36497 = DIRECTION ( 'NONE', ( -0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#36498 = CARTESIAN_POINT ( 'NONE', ( 1.652046208920949999, -1.504992180692799941, 0.8300000000000001821 ) ) ; +#36499 = ORIENTED_EDGE ( 'NONE', *, *, #71327, .F. ) ; +#36500 = LINE ( 'NONE', #36003, #51493 ) ; +#36501 = VECTOR ( 'NONE', #72302, 1000.000000000000000 ) ; +#36502 = ADVANCED_FACE ( 'N', ( #94028 ), #16953, .F. ) ; +#36503 = EDGE_CURVE ( 'NONE', #38574, #15908, #79272, .T. ) ; +#36504 = VECTOR ( 'NONE', #7861, 1000.000000000000000 ) ; +#36505 = EDGE_CURVE ( 'NONE', #26141, #29072, #93397, .T. ) ; +#36506 = STYLED_ITEM ( 'NONE', ( #83398 ), #9511 ) ; +#36507 = ORIENTED_EDGE ( 'NONE', *, *, #28426, .F. ) ; +#36508 = ADVANCED_FACE ( 'NONE', ( #55317 ), #40485, .T. ) ; +#36509 = ORIENTED_EDGE ( 'NONE', *, *, #41961, .T. ) ; +#36510 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56397, 'distance_accuracy_value', 'NONE'); +#36511 = LINE ( 'NONE', #90096, #31178 ) ; +#36513 = CARTESIAN_POINT ( 'NONE', ( -1.171237681315639989, -1.515071875619850017, 0.8299999999999999600 ) ) ; +#36512 = CYLINDRICAL_SURFACE ( 'NONE', #23237, 0.09407705479135430870 ) ; +#36514 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8648700000000000276 ) ) ; +#36515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36516 = ORIENTED_EDGE ( 'NONE', *, *, #8556, .F. ) ; +#36517 = FILL_AREA_STYLE ('',( #51332 ) ) ; +#36518 = ORIENTED_EDGE ( 'NONE', *, *, #87095, .F. ) ; +#36519 = CARTESIAN_POINT ( 'NONE', ( 1.347634412165590101, -1.485054850390570058, 0.8299999999999999600 ) ) ; +#36520 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36521 = ADVANCED_FACE ( 'NONE', ( #18977 ), #35357, .T. ) ; +#36522 = LINE ( 'NONE', #67609, #64427 ) ; +#36523 = LINE ( 'NONE', #44631, #33624 ) ; +#36524 = ORIENTED_EDGE ( 'NONE', *, *, #18104, .F. ) ; +#36525 = CARTESIAN_POINT ( 'NONE', ( 1.773496746821729753, -1.132325613921520091, 0.8099999999999998312 ) ) ; +#36526 = ORIENTED_EDGE ( 'NONE', *, *, #59006, .F. ) ; +#36527 = EDGE_CURVE ( 'NONE', #8523, #26704, #33832, .T. ) ; +#36528 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67455 ) ) ; +#36530 = PRESENTATION_STYLE_ASSIGNMENT (( #74810 ) ) ; +#36529 = CARTESIAN_POINT ( 'NONE', ( 0.2833088984560506729, -1.274230719894705155, 0.8099999999999999423 ) ) ; +#36531 = PLANE ( 'NONE', #29490 ) ; +#36532 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#36533 = AXIS2_PLACEMENT_3D ( 'NONE', #33270, #58291, #40940 ) ; +#36534 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36535 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36536 = ORIENTED_EDGE ( 'NONE', *, *, #10806, .T. ) ; +#36537 = EDGE_LOOP ( 'NONE', ( #26093, #57894, #22531, #89345 ) ) ; +#36538 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8648700000000000276 ) ) ; +#36539 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36540 = LINE ( 'NONE', #89147, #39462 ) ; +#36541 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#36542 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80569 ), #26781 ) ; +#36543 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28367 ), #16970 ) ; +#36544 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36545 = LINE ( 'NONE', #53349, #30736 ) ; +#36546 = SURFACE_STYLE_USAGE ( .BOTH. , #13990 ) ; +#36547 = LINE ( 'NONE', #38038, #14430 ) ; +#36548 = ORIENTED_EDGE ( 'NONE', *, *, #42890, .T. ) ; +#36549 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78941 ) ) ; +#36550 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #39722, #2465 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #61615 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#36551 = EDGE_CURVE ( 'NONE', #20680, #25108, #26172, .T. ) ; +#36553 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36552 = LINE ( 'NONE', #44175, #72378 ) ; +#36554 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34081, 'distance_accuracy_value', 'NONE'); +#36555 = LINE ( 'NONE', #98239, #56649 ) ; +#36556 = LINE ( 'NONE', #13467, #28320 ) ; +#36557 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70780 ) ) ; +#36558 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#36559 = FILL_AREA_STYLE_COLOUR ( '', #27398 ) ; +#36560 = ADVANCED_FACE ( 'NONE', ( #34848 ), #12251, .F. ) ; +#36561 = SURFACE_SIDE_STYLE ('',( #83512 ) ) ; +#36562 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#36563 = ORIENTED_EDGE ( 'NONE', *, *, #25453, .T. ) ; +#36564 = FACE_OUTER_BOUND ( 'NONE', #73497, .T. ) ; +#36565 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36566 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36568 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28387 ), #62662 ) ; +#36567 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.383333333333323090, 1.747825839084783216E-76 ) ) ; +#36569 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2850000000000000311, 0.1458578643762690474 ) ) ; +#36570 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36571 = FILL_AREA_STYLE_COLOUR ( '', #69287 ) ; +#36572 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36574 = CARTESIAN_POINT ( 'NONE', ( 8.199238872965260327, 10.59871312703474011, 0.8648700000000000276 ) ) ; +#36573 = AXIS2_PLACEMENT_3D ( 'NONE', #22200, #7301, #45636 ) ; +#36575 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, 0.2250000000000000333 ) ) ; +#36576 = AXIS2_PLACEMENT_3D ( 'NONE', #68466, #97583, #20010 ) ; +#36577 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.000000000000000000 ) ) ; +#36578 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, -8.400000000000000355, -13.35000000000000142 ) ) ; +#36579 = FILL_AREA_STYLE ('',( #67668 ) ) ; +#36580 = SURFACE_SIDE_STYLE ('',( #5368 ) ) ; +#36581 = EDGE_CURVE ( 'NONE', #88079, #70802, #53305, .T. ) ; +#36582 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#36583 = VECTOR ( 'NONE', #91840, 1000.000000000000114 ) ; +#36584 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#36585 = PLANE ( 'NONE', #19415 ) ; +#36586 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#36587 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, 3.099999999999969891, 0.000000000000000000 ) ) ; +#36588 = LINE ( 'NONE', #20739, #3074 ) ; +#36589 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36590 = VECTOR ( 'NONE', #45855, 1000.000000000000000 ) ; +#36591 = LINE ( 'NONE', #51406, #68317 ) ; +#36592 = SURFACE_STYLE_USAGE ( .BOTH. , #90692 ) ; +#36593 = ORIENTED_EDGE ( 'NONE', *, *, #58572, .T. ) ; +#36594 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41471 ), #34920 ) ; +#36596 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36597 = CARTESIAN_POINT ( 'NONE', ( -0.03082045455219830504, -0.9939892240680031632, 0.8300000000000002931 ) ) ; +#36598 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53529 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64135, #56504, #82477 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36599 = LINE ( 'NONE', #67692, #68969 ) ; +#36600 = FILL_AREA_STYLE ('',( #37100 ) ) ; +#36601 = ORIENTED_EDGE ( 'NONE', *, *, #11505, .F. ) ; +#36602 = SURFACE_STYLE_USAGE ( .BOTH. , #67695 ) ; +#36603 = SURFACE_SIDE_STYLE ('',( #14553 ) ) ; +#36604 = EDGE_CURVE ( 'NONE', #56612, #17079, #22493, .T. ) ; +#36605 = EDGE_LOOP ( 'NONE', ( #21092, #40498, #56627, #3122 ) ) ; +#36606 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#36607 = SURFACE_SIDE_STYLE ('',( #5401 ) ) ; +#36608 = ADVANCED_FACE ( 'NONE', ( #5629 ), #13771, .F. ) ; +#36609 = EDGE_LOOP ( 'NONE', ( #1735, #30295, #57107, #100498 ) ) ; +#36610 = VERTEX_POINT ( 'NONE', #44947 ) ; +#36611 = VECTOR ( 'NONE', #90921, 1000.000000000000000 ) ; +#36612 = STYLED_ITEM ( 'NONE', ( #77982 ), #88558 ) ; +#36613 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36614 = ORIENTED_EDGE ( 'NONE', *, *, #72470, .F. ) ; +#36615 = SURFACE_STYLE_FILL_AREA ( #38600 ) ; +#36616 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36617 = AXIS2_PLACEMENT_3D ( 'NONE', #91652, #92156, #22225 ) ; +#36618 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, -13.40000000000000036 ) ) ; +#36619 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36620 = EDGE_CURVE ( 'NONE', #96599, #934, #30441, .T. ) ; +#36621 = EDGE_CURVE ( 'NONE', #23833, #83788, #14285, .T. ) ; +#36622 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #70357, #63834 ) ; +#36623 = FILL_AREA_STYLE ('',( #5414 ) ) ; +#36625 = ORIENTED_EDGE ( 'NONE', *, *, #47762, .F. ) ; +#36624 = ORIENTED_EDGE ( 'NONE', *, *, #29005, .T. ) ; +#36626 = ADVANCED_FACE ( 'NONE', ( #45439 ), #37350, .F. ) ; +#36627 = ORIENTED_EDGE ( 'NONE', *, *, #79707, .F. ) ; +#36628 = EDGE_CURVE ( 'NONE', #56185, #61734, #70459, .T. ) ; +#36629 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597380222, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#36630 = LINE ( 'NONE', #5420, #49189 ) ; +#36631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7139 ), #39890 ) ; +#36633 = VECTOR ( 'NONE', #74862, 1000.000000000000000 ) ; +#36632 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60673, 'distance_accuracy_value', 'NONE'); +#36634 = SURFACE_STYLE_USAGE ( .BOTH. , #76402 ) ; +#36636 = CARTESIAN_POINT ( 'NONE', ( 1.205401789321949968, -0.8845642871695170717, 0.8299999999999999600 ) ) ; +#36635 = LINE ( 'NONE', #43258, #1713 ) ; +#36637 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #47471, #32172, #85260, #84757 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36638 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#36639 = EDGE_CURVE ( 'NONE', #92405, #64323, #62843, .T. ) ; +#36640 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36641 = CARTESIAN_POINT ( 'NONE', ( -1.332669063737389914, -0.9509517096142480197, 0.8100000000000000533 ) ) ; +#36642 = VERTEX_POINT ( 'NONE', #8 ) ; +#36643 = FILL_AREA_STYLE_COLOUR ( '', #79733 ) ; +#36644 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36645 = ORIENTED_EDGE ( 'NONE', *, *, #4488, .T. ) ; +#36646 = EDGE_LOOP ( 'NONE', ( #63163, #31952, #19784, #13980 ) ) ; +#36647 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36648 = EDGE_CURVE ( 'NONE', #75645, #90881, #54678, .T. ) ; +#36649 = VECTOR ( 'NONE', #25899, 1000.000000000000000 ) ; +#36650 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36651 = ORIENTED_EDGE ( 'NONE', *, *, #17809, .F. ) ; +#36652 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14751 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43756, #21781, #74923 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36653 = SURFACE_SIDE_STYLE ('',( #75929 ) ) ; +#36654 = STYLED_ITEM ( 'NONE', ( #53601 ), #12513 ) ; +#36655 = PRESENTATION_STYLE_ASSIGNMENT (( #90757 ) ) ; +#36656 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36657 = ORIENTED_EDGE ( 'NONE', *, *, #15706, .F. ) ; +#36659 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#36658 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36660 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36661 = ORIENTED_EDGE ( 'NONE', *, *, #97072, .F. ) ; +#36662 = EDGE_LOOP ( 'NONE', ( #61018, #60715, #17584, #40510 ) ) ; +#36664 = SURFACE_SIDE_STYLE ('',( #65789 ) ) ; +#36663 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#36665 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#36666 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#36667 = STYLED_ITEM ( 'NONE', ( #6010 ), #68075 ) ; +#36668 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#36669 = SURFACE_SIDE_STYLE ('',( #68266 ) ) ; +#36670 = LINE ( 'NONE', #27500, #8609 ) ; +#36671 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36672 = PLANE ( 'NONE', #100662 ) ; +#36673 = VERTEX_POINT ( 'NONE', #69953 ) ; +#36674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36675 = ORIENTED_EDGE ( 'NONE', *, *, #93055, .T. ) ; +#36676 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36677 = CARTESIAN_POINT ( 'NONE', ( -0.08168056302834829363, -0.9656914468017120390, 0.8299999999999999600 ) ) ; +#36678 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36679 = FILL_AREA_STYLE_COLOUR ( '', #48062 ) ; +#36680 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#36681 = AXIS2_PLACEMENT_3D ( 'NONE', #99467, #91399, #66905 ) ; +#36682 = PRESENTATION_STYLE_ASSIGNMENT (( #75458 ) ) ; +#36683 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36684 = EDGE_CURVE ( 'NONE', #98340, #55863, #85784, .T. ) ; +#36685 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4600000000000000200, -0.2350000000000000144 ) ) ; +#36686 = EDGE_LOOP ( 'NONE', ( #55727, #81922, #62485, #89480 ) ) ; +#36687 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#36688 = DIRECTION ( 'NONE', ( -2.168404344971010347E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36689 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36690 = VECTOR ( 'NONE', #100852, 1000.000000000000000 ) ; +#36691 = CARTESIAN_POINT ( 'NONE', ( 1.818850168448489901, -1.194792006717259936, 0.8299999999999999600 ) ) ; +#36692 = FACE_OUTER_BOUND ( 'NONE', #41535, .T. ) ; +#36694 = FILL_AREA_STYLE_COLOUR ( '', #28796 ) ; +#36693 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36695 = FILL_AREA_STYLE_COLOUR ( '', #45633 ) ; +#36696 = SURFACE_STYLE_USAGE ( .BOTH. , #83656 ) ; +#36697 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#36698 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8217, #92048, #86419 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36700 = ORIENTED_EDGE ( 'NONE', *, *, #79509, .T. ) ; +#36699 = AXIS2_PLACEMENT_3D ( 'NONE', #11108, #18331, #50545 ) ; +#36701 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.323820061220084998, 0.000000000000000000 ) ) ; +#36702 = ORIENTED_EDGE ( 'NONE', *, *, #1118, .T. ) ; +#36703 = SURFACE_SIDE_STYLE ('',( #5495 ) ) ; +#36704 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#36705 = PLANE ( 'NONE', #23607 ) ; +#36706 = LINE ( 'NONE', #98883, #61601 ) ; +#36707 = STYLED_ITEM ( 'NONE', ( #99062 ), #38727 ) ; +#36708 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#36709 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36710 = STYLED_ITEM ( 'NONE', ( #34930 ), #98091 ) ; +#36711 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#36712 = VERTEX_POINT ( 'NONE', #32696 ) ; +#36713 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36714 = STYLED_ITEM ( 'NONE', ( #99186 ), #3507 ) ; +#36715 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.123820061220085265, 0.000000000000000000 ) ) ; +#36716 = PRESENTATION_STYLE_ASSIGNMENT (( #5510 ) ) ; +#36717 = STYLED_ITEM ( 'NONE', ( #100133 ), #12615 ) ; +#36718 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#36719 = EDGE_CURVE ( 'NONE', #90134, #69855, #1038, .T. ) ; +#36720 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36721 = ORIENTED_EDGE ( 'NONE', *, *, #63667, .T. ) ; +#36722 = ORIENTED_EDGE ( 'NONE', *, *, #43658, .T. ) ; +#36723 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2168 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32339, #7740, #61986 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36724 = FILL_AREA_STYLE_COLOUR ( '', #43862 ) ; +#36725 = EDGE_LOOP ( 'NONE', ( #64470, #1915, #50504, #30625 ) ) ; +#36726 = SURFACE_STYLE_FILL_AREA ( #3575 ) ; +#36727 = VECTOR ( 'NONE', #88375, 1000.000000000000114 ) ; +#36728 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#36729 = LINE ( 'NONE', #21388, #43368 ) ; +#36730 = FACE_OUTER_BOUND ( 'NONE', #22886, .T. ) ; +#36731 = SURFACE_STYLE_USAGE ( .BOTH. , #20384 ) ; +#36732 = CARTESIAN_POINT ( 'NONE', ( -1.287544264014619966, -1.018544155089240011, 0.8299999999999999600 ) ) ; +#36733 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90505 ), #28556 ) ; +#36735 = EDGE_LOOP ( 'NONE', ( #87880, #13725, #92234, #25985 ) ) ; +#36734 = ORIENTED_EDGE ( 'NONE', *, *, #91707, .F. ) ; +#36736 = ORIENTED_EDGE ( 'NONE', *, *, #97976, .T. ) ; +#36737 = CARTESIAN_POINT ( 'NONE', ( 1.617430281440369821, -0.9137302873894740385, 0.8099999999999981659 ) ) ; +#36738 = AXIS2_PLACEMENT_3D ( 'NONE', #48648, #62460, #93534 ) ; +#36739 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88017, 'distance_accuracy_value', 'NONE'); +#36740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38, 'distance_accuracy_value', 'NONE'); +#36741 = ORIENTED_EDGE ( 'NONE', *, *, #35669, .T. ) ; +#36743 = ORIENTED_EDGE ( 'NONE', *, *, #46091, .F. ) ; +#36742 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85852 ) ) ; +#36744 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999959338, -0.1399999999999999856 ) ) ; +#36746 = LINE ( 'NONE', #28095, #31963 ) ; +#36745 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8099999999999999423 ) ) ; +#36747 = FILL_AREA_STYLE ('',( #5555 ) ) ; +#36748 = VERTEX_POINT ( 'NONE', #33194 ) ; +#36749 = ORIENTED_EDGE ( 'NONE', *, *, #93941, .T. ) ; +#36750 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36751 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13792 ) ) ; +#36752 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36753 = ORIENTED_EDGE ( 'NONE', *, *, #34282, .T. ) ; +#36754 = FILL_AREA_STYLE ('',( #51604 ) ) ; +#36755 = EDGE_CURVE ( 'NONE', #45808, #95472, #47490, .T. ) ; +#36756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54421 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88853, #73544, #34758 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36757 = DIRECTION ( 'NONE', ( -0.7071064476869688420, -0.7071071146859688739, 0.000000000000000000 ) ) ; +#36759 = ORIENTED_EDGE ( 'NONE', *, *, #71894, .F. ) ; +#36758 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -4.344024262657780003E-34 ) ) ; +#36760 = LINE ( 'NONE', #6041, #92201 ) ; +#36761 = ORIENTED_EDGE ( 'NONE', *, *, #5660, .T. ) ; +#36763 = LINE ( 'NONE', #61275, #94078 ) ; +#36762 = VECTOR ( 'NONE', #84161, 1000.000000000000000 ) ; +#36764 = FACE_OUTER_BOUND ( 'NONE', #31295, .T. ) ; +#36765 = ORIENTED_EDGE ( 'NONE', *, *, #65633, .F. ) ; +#36766 = VERTEX_POINT ( 'NONE', #23525 ) ; +#36767 = LINE ( 'NONE', #22963, #17161 ) ; +#36768 = SURFACE_SIDE_STYLE ('',( #98457 ) ) ; +#36769 = AXIS2_PLACEMENT_3D ( 'NONE', #25644, #88421, #73108 ) ; +#36770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36771 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#36772 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36773 = VECTOR ( 'NONE', #80149, 1000.000000000000000 ) ; +#36774 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#36775 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#36777 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#36776 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8199999999999999512 ) ) ; +#36778 = EDGE_CURVE ( 'NONE', #29915, #89863, #63361, .T. ) ; +#36779 = ORIENTED_EDGE ( 'NONE', *, *, #72595, .F. ) ; +#36780 = SURFACE_SIDE_STYLE ('',( #5582 ) ) ; +#36781 = VERTEX_POINT ( 'NONE', #46983 ) ; +#36782 = STYLED_ITEM ( 'NONE', ( #6163 ), #3748 ) ; +#36783 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36784 = CARTESIAN_POINT ( 'NONE', ( -0.2991008533676399739, -1.396584910994119966, 0.8299999999999999600 ) ) ; +#36785 = STYLED_ITEM ( 'NONE', ( #14179 ), #12745 ) ; +#36786 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207790140, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#36787 = FILL_AREA_STYLE ('',( #21449 ) ) ; +#36788 = SURFACE_SIDE_STYLE ('',( #36300 ) ) ; +#36789 = CARTESIAN_POINT ( 'NONE', ( 1.693812380665640216, -1.164588072778879990, 0.8100000000000000533 ) ) ; +#36790 = ADVANCED_FACE ( 'NONE', ( #8590 ), #79671, .T. ) ; +#36791 = PLANE ( 'NONE', #29964 ) ; +#36792 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#36793 = FACE_OUTER_BOUND ( 'NONE', #39470, .T. ) ; +#36794 = STYLED_ITEM ( 'NONE', ( #74675 ), #68387 ) ; +#36795 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70853 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62270, #45879, #6551 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36796 = SURFACE_STYLE_USAGE ( .BOTH. , #52631 ) ; +#36797 = PRESENTATION_STYLE_ASSIGNMENT (( #43943 ) ) ; +#36799 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#36798 = FACE_OUTER_BOUND ( 'NONE', #72056, .T. ) ; +#36800 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999961697, -0.02000000000001260145 ) ) ; +#36801 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61585 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44946, #76122, #99507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36802 = VECTOR ( 'NONE', #28140, 1000.000000000000000 ) ; +#36803 = VERTEX_POINT ( 'NONE', #25054 ) ; +#36804 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36805 = AXIS2_PLACEMENT_3D ( 'NONE', #78417, #8374, #40132 ) ; +#36806 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#36807 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15489, 'distance_accuracy_value', 'NONE'); +#36808 = ADVANCED_FACE ( 'NONE', ( #17340 ), #87302, .T. ) ; +#36809 = LINE ( 'NONE', #76105, #100236 ) ; +#36810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36811 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36812 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36813 = FILL_AREA_STYLE ('',( #83280 ) ) ; +#36814 = LINE ( 'NONE', #13241, #25491 ) ; +#36816 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.5000000000000000000, -11.57000000000000028 ) ) ; +#36815 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43297 ), #89011 ) ; +#36817 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.583333333333333481, 0.000000000000000000 ) ) ; +#36818 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#36819 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #11768, #26206 ), + ( #27718, #96100 ), + ( #81842, #18508 ), + ( #58878, #95590 ), + ( #26709, #2210 ), + ( #56856, #49695 ), + ( #80836, #81350 ), + ( #42523, #10768 ), + ( #42018, #73654 ), + ( #12799, #22535 ), + ( #6638, #75653 ), + ( #82825, #37865 ), + ( #35880, #44488 ), + ( #36867, #91481 ), + ( #59384, #100024 ), + ( #5665, #52203 ), + ( #36366, #83331 ), + ( #98061, #28206 ), + ( #28690, #90475 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06582945268006269723, 0.1283337680849729878, 0.1881073333815090065, 0.2448260797502359865, 0.2995261574541620009, 0.3534890227489490000, 0.4069931702810409835, 0.4605296998696790101, 0.5149049356132150423, 0.5719520573060270507, 0.6322548437923299902, 0.6956432724647799715, 0.7644393464154890516, 0.8371968441801660443, 0.9155905157404520267, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36820 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#36821 = STYLED_ITEM ( 'NONE', ( #39750 ), #77698 ) ; +#36822 = ORIENTED_EDGE ( 'NONE', *, *, #21966, .F. ) ; +#36823 = ORIENTED_EDGE ( 'NONE', *, *, #16360, .F. ) ; +#36824 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36825 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79262, 'distance_accuracy_value', 'NONE'); +#36826 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45435, 'distance_accuracy_value', 'NONE'); +#36827 = FACE_OUTER_BOUND ( 'NONE', #43485, .T. ) ; +#36828 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36829 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#36830 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155850987, 0.8100000000000249223 ) ) ; +#36831 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2761799387799150352, 0.000000000000000000 ) ) ; +#36832 = VECTOR ( 'NONE', #81187, 1000.000000000000000 ) ; +#36833 = FILL_AREA_STYLE_COLOUR ( '', #2568 ) ; +#36834 = FILL_AREA_STYLE_COLOUR ( '', #100540 ) ; +#36835 = FILL_AREA_STYLE ('',( #12765 ) ) ; +#36836 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8100000000001583711 ) ) ; +#36837 = STYLED_ITEM ( 'NONE', ( #6718 ), #22622 ) ; +#36838 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36839 = ORIENTED_EDGE ( 'NONE', *, *, #82532, .F. ) ; +#36840 = EDGE_CURVE ( 'NONE', #47444, #34980, #26549, .T. ) ; +#36841 = FACE_OUTER_BOUND ( 'NONE', #14106, .T. ) ; +#36842 = EDGE_CURVE ( 'NONE', #69664, #46588, #81688, .T. ) ; +#36844 = VECTOR ( 'NONE', #82113, 1000.000000000000000 ) ; +#36843 = PRESENTATION_STYLE_ASSIGNMENT (( #91458 ) ) ; +#36845 = ORIENTED_EDGE ( 'NONE', *, *, #59003, .F. ) ; +#36846 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36847 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100330 ), #17284 ) ; +#36848 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36849 = ORIENTED_EDGE ( 'NONE', *, *, #76593, .F. ) ; +#36850 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000000513, 0.8991599999999999593 ) ) ; +#36851 = LINE ( 'NONE', #4190, #65885 ) ; +#36852 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#36853 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36854 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36856 = VERTEX_POINT ( 'NONE', #33711 ) ; +#36855 = VERTEX_POINT ( 'NONE', #2549 ) ; +#36857 = FILL_AREA_STYLE ('',( #66980 ) ) ; +#36858 = ORIENTED_EDGE ( 'NONE', *, *, #74172, .T. ) ; +#36860 = EDGE_CURVE ( 'NONE', #38581, #46653, #80684, .T. ) ; +#36859 = STYLED_ITEM ( 'NONE', ( #5410 ), #12857 ) ; +#36861 = FILL_AREA_STYLE_COLOUR ( '', #59097 ) ; +#36863 = CARTESIAN_POINT ( 'NONE', ( -0.5701283358897649700, -0.9702412545157700352, 0.8299999999999999600 ) ) ; +#36862 = SURFACE_STYLE_USAGE ( .BOTH. , #37858 ) ; +#36864 = ORIENTED_EDGE ( 'NONE', *, *, #32854, .T. ) ; +#36865 = VERTEX_POINT ( 'NONE', #97452 ) ; +#36866 = SURFACE_STYLE_FILL_AREA ( #60376 ) ; +#36867 = CARTESIAN_POINT ( 'NONE', ( -0.5167618201584639470, -1.182153033657940000, 0.8100000000000000533 ) ) ; +#36868 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36869 = FILL_AREA_STYLE ('',( #81844 ) ) ; +#36870 = ORIENTED_EDGE ( 'NONE', *, *, #76844, .T. ) ; +#36872 = ORIENTED_EDGE ( 'NONE', *, *, #94433, .T. ) ; +#36871 = VECTOR ( 'NONE', #83619, 1000.000000000000000 ) ; +#36873 = EDGE_LOOP ( 'NONE', ( #67960, #77429, #3222, #40394 ) ) ; +#36874 = EDGE_CURVE ( 'NONE', #28792, #35510, #10508, .T. ) ; +#36875 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28699 ), #22209 ) ; +#36877 = EDGE_LOOP ( 'NONE', ( #24299, #14132, #19688, #74692 ) ) ; +#36876 = LINE ( 'NONE', #13819, #23301 ) ; +#36878 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -1.699999999999999734, 0.8299999999999999600 ) ) ; +#36879 = AXIS2_PLACEMENT_3D ( 'NONE', #35039, #44650, #60028 ) ; +#36880 = PLANE ( 'NONE', #31888 ) ; +#36881 = SURFACE_SIDE_STYLE ('',( #100045 ) ) ; +#36882 = VERTEX_POINT ( 'NONE', #66835 ) ; +#36883 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -4.032509280197754099E-17, 0.2499999999999999445 ) ) ; +#36884 = EDGE_LOOP ( 'NONE', ( #75575, #18832, #92126, #73281 ) ) ; +#36885 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84105 ) ) ; +#36886 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92320 ) ) ; +#36887 = FACE_OUTER_BOUND ( 'NONE', #2355, .T. ) ; +#36888 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36889 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95521 ) ) ; +#36890 = STYLED_ITEM ( 'NONE', ( #15185 ), #49090 ) ; +#36891 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#36892 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#36893 = PLANE ( 'NONE', #17003 ) ; +#36894 = CARTESIAN_POINT ( 'NONE', ( -1.159471497952200947, -1.151210320156311973, 0.8099999999998764855 ) ) ; +#36895 = ADVANCED_FACE ( 'NONE', ( #42375 ), #4050, .T. ) ; +#36896 = STYLED_ITEM ( 'NONE', ( #52958 ), #77887 ) ; +#36897 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25474 ) ) ; +#36898 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#36899 = ORIENTED_EDGE ( 'NONE', *, *, #28481, .F. ) ; +#36900 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36901 = CARTESIAN_POINT ( 'NONE', ( 1.381901993660050065, -1.214210613447320064, 0.8300000000000022915 ) ) ; +#36903 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36902 = FILL_AREA_STYLE ('',( #30217 ) ) ; +#36904 = LINE ( 'NONE', #5204, #58424 ) ; +#36905 = PLANE ( 'NONE', #74491 ) ; +#36906 = ADVANCED_FACE ( 'NONE', ( #4542 ), #28063, .T. ) ; +#36907 = STYLED_ITEM ( 'NONE', ( #75366 ), #99623 ) ; +#36909 = ADVANCED_FACE ( 'NONE', ( #68813 ), #75502, .T. ) ; +#36908 = LINE ( 'NONE', #4743, #73599 ) ; +#36910 = VERTEX_POINT ( 'NONE', #98398 ) ; +#36911 = VECTOR ( 'NONE', #78506, 1000.000000000000000 ) ; +#36912 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.100000000000000089 ) ) ; +#36913 = PLANE ( 'NONE', #25120 ) ; +#36914 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36915 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#36916 = ORIENTED_EDGE ( 'NONE', *, *, #54981, .F. ) ; +#36917 = SURFACE_STYLE_USAGE ( .BOTH. , #83386 ) ; +#36918 = EDGE_CURVE ( 'NONE', #449, #33336, #76495, .T. ) ; +#36919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36920 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23897 ), #54868 ) ; +#36921 = FILL_AREA_STYLE ('',( #81896 ) ) ; +#36922 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40218 ) ) ; +#36923 = PRESENTATION_STYLE_ASSIGNMENT (( #44066 ) ) ; +#36924 = ORIENTED_EDGE ( 'NONE', *, *, #26572, .T. ) ; +#36925 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36926 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8648700000000000276 ) ) ; +#36927 = FILL_AREA_STYLE ('',( #30239 ) ) ; +#36928 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8991599999999999593 ) ) ; +#36929 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#36930 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#36931 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36932 = AXIS2_PLACEMENT_3D ( 'NONE', #39917, #94517, #33784 ) ; +#36933 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36934 = SURFACE_STYLE_USAGE ( .BOTH. , #52274 ) ; +#36935 = SURFACE_SIDE_STYLE ('',( #77225 ) ) ; +#36936 = EDGE_CURVE ( 'NONE', #79206, #6999, #30504, .T. ) ; +#36937 = ADVANCED_FACE ( 'NONE', ( #99390 ), #45820, .T. ) ; +#36938 = PRESENTATION_STYLE_ASSIGNMENT (( #44564 ) ) ; +#36939 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10970, 'distance_accuracy_value', 'NONE'); +#36940 = STYLED_ITEM ( 'NONE', ( #44532 ), #30234 ) ; +#36941 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#36942 = ORIENTED_EDGE ( 'NONE', *, *, #39778, .T. ) ; +#36943 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#36944 = ORIENTED_EDGE ( 'NONE', *, *, #27887, .F. ) ; +#36945 = FACE_OUTER_BOUND ( 'NONE', #68924, .T. ) ; +#36946 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19233, 'distance_accuracy_value', 'NONE'); +#36947 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94710, 'distance_accuracy_value', 'NONE'); +#36948 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#36949 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8648700000000000276 ) ) ; +#36950 = SURFACE_SIDE_STYLE ('',( #22629 ) ) ; +#36951 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18933 ), #14001 ) ; +#36952 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#36953 = CARTESIAN_POINT ( 'NONE', ( 1.799170355476140015, -0.9218577280486121017, 0.8299999999999999600 ) ) ; +#36954 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#36955 = ORIENTED_EDGE ( 'NONE', *, *, #56809, .T. ) ; +#36956 = EDGE_CURVE ( 'NONE', #43386, #2486, #88589, .T. ) ; +#36958 = FILL_AREA_STYLE_COLOUR ( '', #43240 ) ; +#36957 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4933 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87781, #50522, #56674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36959 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64916, 'distance_accuracy_value', 'NONE'); +#36960 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36961 = EDGE_CURVE ( 'NONE', #79988, #6603, #32575, .T. ) ; +#36962 = FACE_OUTER_BOUND ( 'NONE', #95549, .T. ) ; +#36963 = PLANE ( 'NONE', #63453 ) ; +#36964 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61467 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13446, #52841, #6299 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#36965 = ORIENTED_EDGE ( 'NONE', *, *, #91200, .T. ) ; +#36966 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#36967 = CARTESIAN_POINT ( 'NONE', ( 1.309875304108520044, -1.500691070757680157, 0.8299999999999994049 ) ) ; +#36968 = VECTOR ( 'NONE', #21268, 1000.000000000000000 ) ; +#36969 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#36970 = SURFACE_SIDE_STYLE ('',( #11877 ) ) ; +#36971 = PLANE ( 'NONE', #7310 ) ; +#36972 = LINE ( 'NONE', #68079, #25150 ) ; +#36973 = VECTOR ( 'NONE', #1889, 1000.000000000000000 ) ; +#36974 = ORIENTED_EDGE ( 'NONE', *, *, #44249, .T. ) ; +#36975 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#36976 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#36977 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5338, 'distance_accuracy_value', 'NONE'); +#36979 = VECTOR ( 'NONE', #33041, 1000.000000000000000 ) ; +#36978 = SURFACE_STYLE_USAGE ( .BOTH. , #53301 ) ; +#36980 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#36981 = EDGE_CURVE ( 'NONE', #40642, #18766, #8994, .T. ) ; +#36982 = SURFACE_STYLE_FILL_AREA ( #100622 ) ; +#36983 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#36984 = CLOSED_SHELL ( 'NONE', ( #7559, #96079, #81714, #51940, #11819, #58520 ) ) ; +#36985 = VERTEX_POINT ( 'NONE', #62221 ) ; +#36986 = VECTOR ( 'NONE', #16650, 1000.000000000000000 ) ; +#36987 = VECTOR ( 'NONE', #45553, 1000.000000000000000 ) ; +#36988 = SURFACE_SIDE_STYLE ('',( #20132 ) ) ; +#36989 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 5.528756999999999699, 0.8648700000000000276 ) ) ; +#36990 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#36991 = CARTESIAN_POINT ( 'NONE', ( 1.508691354424569919, -1.396584910994119966, 0.8300000000000001821 ) ) ; +#36992 = EDGE_LOOP ( 'NONE', ( #47669, #7225, #70089, #85864 ) ) ; +#36993 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93006, #71091, #78255, #40465 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#36994 = VECTOR ( 'NONE', #40741, 1000.000000000000000 ) ; +#36995 = VECTOR ( 'NONE', #20040, 1000.000000000000000 ) ; +#36996 = EDGE_CURVE ( 'NONE', #8286, #74773, #24430, .T. ) ; +#36997 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20648 ), #41888 ) ; +#36998 = ORIENTED_EDGE ( 'NONE', *, *, #27577, .F. ) ; +#37000 = ORIENTED_EDGE ( 'NONE', *, *, #71966, .F. ) ; +#36999 = LINE ( 'NONE', #60499, #2024 ) ; +#37001 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#37002 = FACE_OUTER_BOUND ( 'NONE', #81602, .T. ) ; +#37003 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#37004 = LINE ( 'NONE', #99188, #87882 ) ; +#37005 = ORIENTED_EDGE ( 'NONE', *, *, #7111, .F. ) ; +#37006 = SURFACE_SIDE_STYLE ('',( #11912 ) ) ; +#37007 = CARTESIAN_POINT ( 'NONE', ( -0.5614853896103889630, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#37008 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#37009 = ORIENTED_EDGE ( 'NONE', *, *, #53797, .F. ) ; +#37010 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#37011 = SURFACE_STYLE_USAGE ( .BOTH. , #75796 ) ; +#37012 = SURFACE_SIDE_STYLE ('',( #51837 ) ) ; +#37013 = AXIS2_PLACEMENT_3D ( 'NONE', #68333, #15172, #14681 ) ; +#37014 = ORIENTED_EDGE ( 'NONE', *, *, #93585, .F. ) ; +#37015 = VECTOR ( 'NONE', #32537, 1000.000000000000000 ) ; +#37016 = LINE ( 'NONE', #92113, #61866 ) ; +#37017 = ORIENTED_EDGE ( 'NONE', *, *, #25871, .T. ) ; +#37018 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#37019 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37020 = LINE ( 'NONE', #25732, #58834 ) ; +#37021 = EDGE_CURVE ( 'NONE', #57504, #8103, #28871, .T. ) ; +#37022 = LINE ( 'NONE', #68124, #91434 ) ; +#37023 = PRESENTATION_STYLE_ASSIGNMENT (( #54352 ) ) ; +#37024 = VECTOR ( 'NONE', #61723, 1000.000000000000114 ) ; +#37025 = LINE ( 'NONE', #20677, #5044 ) ; +#37026 = ORIENTED_EDGE ( 'NONE', *, *, #81270, .F. ) ; +#37027 = FILL_AREA_STYLE ('',( #44159 ) ) ; +#37028 = ORIENTED_EDGE ( 'NONE', *, *, #2964, .F. ) ; +#37029 = LINE ( 'NONE', #27883, #30755 ) ; +#37030 = FACE_OUTER_BOUND ( 'NONE', #64035, .T. ) ; +#37031 = FILL_AREA_STYLE_COLOUR ( '', #15855 ) ; +#37032 = EDGE_CURVE ( 'NONE', #75181, #100533, #93295, .T. ) ; +#37033 = EDGE_CURVE ( 'NONE', #99402, #32262, #69831, .T. ) ; +#37034 = AXIS2_PLACEMENT_3D ( 'NONE', #62574, #100214, #753 ) ; +#37035 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37036 = SURFACE_STYLE_FILL_AREA ( #62036 ) ; +#37037 = VECTOR ( 'NONE', #30711, 1000.000000000000000 ) ; +#37039 = EDGE_CURVE ( 'NONE', #4405, #68885, #31050, .T. ) ; +#37038 = PRESENTATION_STYLE_ASSIGNMENT (( #20178 ) ) ; +#37040 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#37041 = LINE ( 'NONE', #52856, #83368 ) ; +#37042 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37043 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37044 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6552, #37773, #63787, #85724 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37045 = PLANE ( 'NONE', #92779 ) ; +#37046 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87613 ) ) ; +#37047 = ORIENTED_EDGE ( 'NONE', *, *, #22779, .F. ) ; +#37048 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.000000000000000000 ) ) ; +#37049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43673 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20635, #51805, #4322 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37050 = EDGE_CURVE ( 'NONE', #42285, #45524, #55670, .T. ) ; +#37052 = PRESENTATION_STYLE_ASSIGNMENT (( #13465 ) ) ; +#37051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37053 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#37054 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#37055 = AXIS2_PLACEMENT_3D ( 'NONE', #6821, #92641, #53886 ) ; +#37056 = VECTOR ( 'NONE', #86815, 1000.000000000000000 ) ; +#37057 = SURFACE_STYLE_USAGE ( .BOTH. , #98735 ) ; +#37058 = SHAPE_REPRESENTATION ( 'Submodel-L0201_part_L0201', ( #41901, #40303 ), #50086 ) ; +#37059 = CLOSED_SHELL ( 'NONE', ( #95605, #55101, #69996, #68554, #72678, #19433 ) ) ; +#37060 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37061 = ORIENTED_EDGE ( 'NONE', *, *, #50, .T. ) ; +#37062 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37063 = VECTOR ( 'NONE', #28866, 1000.000000000000000 ) ; +#37064 = SURFACE_STYLE_USAGE ( .BOTH. , #37562 ) ; +#37065 = CARTESIAN_POINT ( 'NONE', ( 1.666984577922079991, -1.164935064935060050, 0.8100000000000000533 ) ) ; +#37066 = VECTOR ( 'NONE', #30138, 1000.000000000000114 ) ; +#37067 = LINE ( 'NONE', #68660, #80783 ) ; +#37068 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#37069 = LINE ( 'NONE', #76852, #66070 ) ; +#37070 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#37071 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#37072 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58310 ) ) ; +#37073 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37075 = ADVANCED_FACE ( 'NONE', ( #16694 ), #29368, .T. ) ; +#37074 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#37076 = EDGE_CURVE ( 'NONE', #89960, #42509, #29850, .T. ) ; +#37077 = PLANE ( 'NONE', #63810 ) ; +#37078 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19113 ), #43598 ) ; +#37079 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37080 = LINE ( 'NONE', #68175, #99233 ) ; +#37081 = SURFACE_STYLE_USAGE ( .BOTH. , #5863 ) ; +#37082 = LINE ( 'NONE', #43700, #31720 ) ; +#37083 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999990674, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#37084 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37085 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81066, 'distance_accuracy_value', 'NONE'); +#37086 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37087 = CARTESIAN_POINT ( 'NONE', ( -0.1190035524734260053, -0.9001377335631759458, 0.8300000000000009592 ) ) ; +#37088 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#37089 = FILL_AREA_STYLE_COLOUR ( '', #10003 ) ; +#37090 = EDGE_LOOP ( 'NONE', ( #51198, #53195, #30143, #29734 ) ) ; +#37091 = FACE_OUTER_BOUND ( 'NONE', #24647, .T. ) ; +#37092 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#37093 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83421, 'distance_accuracy_value', 'NONE'); +#37094 = ADVANCED_FACE ( 'NONE', ( #76828 ), #62041, .T. ) ; +#37095 = PLANE ( 'NONE', #23343 ) ; +#37096 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37097 = VECTOR ( 'NONE', #59571, 1000.000000000000000 ) ; +#37098 = CARTESIAN_POINT ( 'NONE', ( -0.8333333333333386994, -3.500000000000000000, 0.000000000000000000 ) ) ; +#37099 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#37100 = FILL_AREA_STYLE_COLOUR ( '', #43463 ) ; +#37101 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#37102 = ORIENTED_EDGE ( 'NONE', *, *, #85253, .T. ) ; +#37103 = SURFACE_STYLE_FILL_AREA ( #91207 ) ; +#37104 = CARTESIAN_POINT ( 'NONE', ( 6.106202500500176100, 9.368346500500175367, 0.8991599999999999593 ) ) ; +#37105 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42058, 'distance_accuracy_value', 'NONE'); +#37106 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36110 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75005, #82657, #74506 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37107 = LINE ( 'NONE', #60112, #71975 ) ; +#37108 = SURFACE_STYLE_USAGE ( .BOTH. , #89703 ) ; +#37109 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95727 ) ) ; +#37110 = ORIENTED_EDGE ( 'NONE', *, *, #2277, .T. ) ; +#37111 = VERTEX_POINT ( 'NONE', #28856 ) ; +#37112 = CARTESIAN_POINT ( 'NONE', ( 0.4084453376902120181, -0.9740784349584099555, 0.8300000000000002931 ) ) ; +#37113 = VERTEX_POINT ( 'NONE', #5832 ) ; +#37114 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#37115 = VECTOR ( 'NONE', #45141, 1000.000000000000000 ) ; +#37116 = CARTESIAN_POINT ( 'NONE', ( 0.4905624295734890006, -1.210065939746389985, 0.8299999999999999600 ) ) ; +#37117 = CARTESIAN_POINT ( 'NONE', ( -0.9238200612200850870, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#37118 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37119 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96868, #43765, #4942 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37120 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #31303, #23861 ) ; +#37121 = ORIENTED_EDGE ( 'NONE', *, *, #30683, .F. ) ; +#37122 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10929 ) ) ; +#37123 = EDGE_CURVE ( 'NONE', #11725, #49704, #14171, .T. ) ; +#37124 = VERTEX_POINT ( 'NONE', #83998 ) ; +#37125 = STYLED_ITEM ( 'NONE', ( #34953 ), #41366 ) ; +#37126 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37128 = CARTESIAN_POINT ( 'NONE', ( 1.380164001837510090, -0.9588323859052130249, 0.8299999999999999600 ) ) ; +#37127 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37129 = PRESENTATION_STYLE_ASSIGNMENT (( #61625 ) ) ; +#37130 = EDGE_CURVE ( 'NONE', #73645, #22294, #91149, .T. ) ; +#37131 = CLOSED_SHELL ( 'NONE', ( #21295, #72513, #52162, #70671, #16139, #97700 ) ) ; +#37133 = AXIS2_PLACEMENT_3D ( 'NONE', #49498, #71970, #88793 ) ; +#37132 = FILL_AREA_STYLE ('',( #30957 ) ) ; +#37134 = FILL_AREA_STYLE_COLOUR ( '', #8068 ) ; +#37135 = VECTOR ( 'NONE', #66655, 1000.000000000000000 ) ; +#37136 = SURFACE_STYLE_USAGE ( .BOTH. , #66743 ) ; +#37137 = ORIENTED_EDGE ( 'NONE', *, *, #94271, .F. ) ; +#37138 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.05000000000000002359, 0.2100000000000000200 ) ) ; +#37139 = VERTEX_POINT ( 'NONE', #13460 ) ; +#37140 = ORIENTED_EDGE ( 'NONE', *, *, #12403, .T. ) ; +#37141 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#37142 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45245 ) ) ; +#37144 = PRESENTATION_STYLE_ASSIGNMENT (( #74936 ) ) ; +#37143 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1199999999999999956, -0.7500000000000000000 ) ) ; +#37145 = EDGE_CURVE ( 'NONE', #96832, #42509, #99220, .T. ) ; +#37146 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#37147 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#37149 = VERTEX_POINT ( 'NONE', #13991 ) ; +#37148 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37150 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37151 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#37152 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37153 = SURFACE_SIDE_STYLE ('',( #5931 ) ) ; +#37154 = ORIENTED_EDGE ( 'NONE', *, *, #95319, .T. ) ; +#37156 = FILL_AREA_STYLE_COLOUR ( '', #95764 ) ; +#37155 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#37157 = PRESENTATION_STYLE_ASSIGNMENT (( #30977 ) ) ; +#37158 = ORIENTED_EDGE ( 'NONE', *, *, #71327, .T. ) ; +#37159 = ORIENTED_EDGE ( 'NONE', *, *, #45382, .T. ) ; +#37160 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37161 = CARTESIAN_POINT ( 'NONE', ( 1.015677417745509903, -1.448219210431749948, 0.8100000000000010525 ) ) ; +#37162 = EDGE_CURVE ( 'NONE', #37668, #9763, #96800, .T. ) ; +#37163 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#37164 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37165 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#37166 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37167 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22485 ), #43688 ) ; +#37168 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37169 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#37170 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29630 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1888, #81540, #72841 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37171 = ORIENTED_EDGE ( 'NONE', *, *, #85827, .F. ) ; +#37172 = FILL_AREA_STYLE ('',( #66776 ) ) ; +#37173 = ORIENTED_EDGE ( 'NONE', *, *, #9224, .T. ) ; +#37174 = EDGE_CURVE ( 'NONE', #46291, #5298, #49545, .T. ) ; +#37175 = SURFACE_STYLE_FILL_AREA ( #97396 ) ; +#37176 = CARTESIAN_POINT ( 'NONE', ( -0.008099123004813310947, -1.050822088410799937, 0.8100000000000000533 ) ) ; +#37177 = CARTESIAN_POINT ( 'NONE', ( 1.148671667572580102, -1.140452398731560013, 0.8299999999999999600 ) ) ; +#37178 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.724127286303860039E-15, 0.000000000000000000 ) ) ; +#37179 = CIRCLE ( 'NONE', #46899, 0.009999999999999998473 ) ; +#37180 = VECTOR ( 'NONE', #86015, 1000.000000000000000 ) ; +#37181 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37182 = PRESENTATION_STYLE_ASSIGNMENT (( #38661 ) ) ; +#37183 = ADVANCED_FACE ( 'NONE', ( #38471 ), #33213, .T. ) ; +#37184 = LINE ( 'NONE', #68285, #93975 ) ; +#37185 = FILL_AREA_STYLE ('',( #82148 ) ) ; +#37187 = VERTEX_POINT ( 'NONE', #73013 ) ; +#37186 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83587 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27543, #4526, #26039 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37188 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37189 = FACE_OUTER_BOUND ( 'NONE', #92753, .T. ) ; +#37190 = PLANE ( 'NONE', #5641 ) ; +#37191 = SURFACE_SIDE_STYLE ('',( #77983 ) ) ; +#37192 = FILL_AREA_STYLE ('',( #92282 ) ) ; +#37193 = LINE ( 'NONE', #14638, #96301 ) ; +#37194 = VECTOR ( 'NONE', #88513, 1000.000000000000000 ) ; +#37195 = EDGE_CURVE ( 'NONE', #2107, #25261, #24577, .T. ) ; +#37197 = EDGE_CURVE ( 'NONE', #79048, #9989, #40372, .T. ) ; +#37196 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37198 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24153 ), #100736 ) ; +#37199 = SURFACE_STYLE_FILL_AREA ( #44805 ) ; +#37201 = VECTOR ( 'NONE', #50156, 1000.000000000000114 ) ; +#37200 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37202 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37203 = VECTOR ( 'NONE', #46308, 1000.000000000000114 ) ; +#37204 = FILL_AREA_STYLE_COLOUR ( '', #90319 ) ; +#37205 = EDGE_CURVE ( 'NONE', #65564, #69886, #2069, .T. ) ; +#37206 = EDGE_CURVE ( 'NONE', #6547, #91502, #57218, .T. ) ; +#37207 = STYLED_ITEM ( 'NONE', ( #41755 ), #16710 ) ; +#37208 = DIRECTION ( 'NONE', ( 0.7071071146859689849, 0.7071064476869689530, 0.000000000000000000 ) ) ; +#37209 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36222, 'distance_accuracy_value', 'NONE'); +#37210 = ORIENTED_EDGE ( 'NONE', *, *, #65298, .T. ) ; +#37211 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11003 ), #73132 ) ; +#37212 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#37213 = VERTEX_POINT ( 'NONE', #86822 ) ; +#37214 = LINE ( 'NONE', #84154, #46173 ) ; +#37215 = SURFACE_STYLE_USAGE ( .BOTH. , #75002 ) ; +#37216 = EDGE_CURVE ( 'NONE', #15816, #28843, #46078, .T. ) ; +#37217 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54996, 'distance_accuracy_value', 'NONE'); +#37218 = SURFACE_STYLE_FILL_AREA ( #14159 ) ; +#37219 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79640 ), #2950 ) ; +#37220 = LINE ( 'NONE', #7965, #97071 ) ; +#37221 = CARTESIAN_POINT ( 'NONE', ( 0.1238200612200860418, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#37222 = ADVANCED_FACE ( 'NONE', ( #65337 ), #14930, .T. ) ; +#37223 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97520 ), #32324 ) ; +#37224 = LINE ( 'NONE', #76492, #43394 ) ; +#37225 = ORIENTED_EDGE ( 'NONE', *, *, #11751, .F. ) ; +#37226 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#37227 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79648 ), #50302 ) ; +#37228 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37229 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29925, 'distance_accuracy_value', 'NONE'); +#37230 = FILL_AREA_STYLE_COLOUR ( '', #52864 ) ; +#37231 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24919, 'distance_accuracy_value', 'NONE'); +#37232 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37233 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37234 = PRESENTATION_STYLE_ASSIGNMENT (( #13653 ) ) ; +#37235 = EDGE_LOOP ( 'NONE', ( #53562, #1452, #77432, #12047 ) ) ; +#37236 = ORIENTED_EDGE ( 'NONE', *, *, #12494, .T. ) ; +#37237 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #69427, .NOT_KNOWN. ) ; +#37238 = STYLED_ITEM ( 'NONE', ( #25035 ), #32078 ) ; +#37239 = ORIENTED_EDGE ( 'NONE', *, *, #57494, .T. ) ; +#37240 = CARTESIAN_POINT ( 'NONE', ( -0.2295631936502020021, -1.479722134560319979, 0.8299999999999999600 ) ) ; +#37241 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37242 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#37243 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37244 = LINE ( 'NONE', #68347, #75658 ) ; +#37245 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37246 = PRODUCT_CONTEXT ( 'NONE', #39073, 'mechanical' ) ; +#37247 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, -0.2349999999999999867 ) ) ; +#37248 = CARTESIAN_POINT ( 'NONE', ( -1.251886425446270046, -0.9762538161110789758, 0.8100000000000000533 ) ) ; +#37250 = ORIENTED_EDGE ( 'NONE', *, *, #76104, .F. ) ; +#37249 = ORIENTED_EDGE ( 'NONE', *, *, #9877, .T. ) ; +#37251 = EDGE_CURVE ( 'NONE', #58927, #98312, #43367, .T. ) ; +#37252 = ORIENTED_EDGE ( 'NONE', *, *, #34601, .F. ) ; +#37253 = PRESENTATION_STYLE_ASSIGNMENT (( #91353 ) ) ; +#37254 = STYLED_ITEM ( 'NONE', ( #96202 ), #84599 ) ; +#37255 = AXIS2_PLACEMENT_3D ( 'NONE', #15418, #26153, #35342 ) ; +#37257 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#37256 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#37258 = EDGE_LOOP ( 'NONE', ( #97079, #4196, #52707, #41845, #41780, #66487, #24721, #31956 ) ) ; +#37259 = EDGE_CURVE ( 'NONE', #60846, #100744, #52059, .T. ) ; +#37260 = VECTOR ( 'NONE', #14543, 1000.000000000000000 ) ; +#37261 = ORIENTED_EDGE ( 'NONE', *, *, #21603, .F. ) ; +#37262 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37263 = FACE_OUTER_BOUND ( 'NONE', #53023, .T. ) ; +#37264 = SURFACE_STYLE_FILL_AREA ( #6027 ) ; +#37265 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53571 ) ) ; +#37267 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37266 = PRESENTATION_STYLE_ASSIGNMENT (( #35767 ) ) ; +#37268 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, -0.2399999999999999356 ) ) ; +#37269 = ORIENTED_EDGE ( 'NONE', *, *, #53844, .T. ) ; +#37270 = ORIENTED_EDGE ( 'NONE', *, *, #91813, .F. ) ; +#37271 = ORIENTED_EDGE ( 'NONE', *, *, #53645, .F. ) ; +#37272 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89212 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58774, #52102, #44883 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37273 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37274 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37275 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24233 ), #11068 ) ; +#37277 = ORIENTED_EDGE ( 'NONE', *, *, #78408, .T. ) ; +#37276 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58406, 'distance_accuracy_value', 'NONE'); +#37278 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#37280 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63388 ), #84333 ) ; +#37279 = PRESENTATION_STYLE_ASSIGNMENT (( #13701 ) ) ; +#37281 = ORIENTED_EDGE ( 'NONE', *, *, #71743, .T. ) ; +#37282 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.000000000000000000, -12.24500000000000099 ) ) ; +#37283 = CIRCLE ( 'NONE', #69884, 0.009999999999999998473 ) ; +#37284 = VERTEX_POINT ( 'NONE', #11632 ) ; +#37285 = ORIENTED_EDGE ( 'NONE', *, *, #80617, .T. ) ; +#37286 = LINE ( 'NONE', #46908, #53581 ) ; +#37287 = ADVANCED_FACE ( 'NONE', ( #4063 ), #75036, .T. ) ; +#37288 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#37289 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #39446, #23642, #94032, #24164, #63479, #39967, #56331, #47621, #87429, #71105, #1148, #32308, #17458, #94563, #55803, #7220, #9237, #38458, #69567 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.139749904431101444E-05, 4.167926570800358524E-05, 6.117642585279009569E-05, 8.007125617966602180E-05, 9.849555549675319494E-05, 0.0001164573492433742239, 0.0001342794739313985810, 0.0001521830310466187972, 0.0001701165620495484455, 0.0001883875854461586580, 0.0002070280353969963392, 0.0002264193111612932395, 0.0002460901620273229519, 0.0002661920138351975295, 0.0002865739416040802789, 0.0003074733952738174228 ), + .UNSPECIFIED. ) ; +#37290 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37291 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64971 ), #92681 ) ; +#37293 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37292 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88431 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71860, #17201, #72343 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37294 = CARTESIAN_POINT ( 'NONE', ( 0.9977603010112831017, -1.128484622308769891, 0.8299999999999997380 ) ) ; +#37295 = PLANE ( 'NONE', #48159 ) ; +#37296 = PRESENTATION_STYLE_ASSIGNMENT (( #76561 ) ) ; +#37297 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37298 = VERTEX_POINT ( 'NONE', #44348 ) ; +#37299 = CARTESIAN_POINT ( 'NONE', ( 0.4674268961122319821, -1.076021161212330046, 0.8100000000000000533 ) ) ; +#37300 = ORIENTED_EDGE ( 'NONE', *, *, #100508, .F. ) ; +#37301 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75617 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99000, #29643, #83295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37303 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000971, 0.1499999999999999944 ) ) ; +#37304 = FILL_AREA_STYLE_COLOUR ( '', #56840 ) ; +#37305 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#37306 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37307 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37308 = CARTESIAN_POINT ( 'NONE', ( -1.384335136307129899, -1.374349516767729984, 0.8300000000000024025 ) ) ; +#37309 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37310 = LINE ( 'NONE', #2762, #19999 ) ; +#37311 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73167 ) ) ; +#37312 = VECTOR ( 'NONE', #88732, 1000.000000000000000 ) ; +#37313 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37314 = STYLED_ITEM ( 'NONE', ( #82996 ), #92670 ) ; +#37315 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62315 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77473, #17196, #15674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37316 = LINE ( 'NONE', #60802, #83118 ) ; +#37318 = LINE ( 'NONE', #98002, #17554 ) ; +#37317 = FILL_AREA_STYLE ('',( #69404 ) ) ; +#37319 = LINE ( 'NONE', #5606, #3209 ) ; +#37320 = SURFACE_SIDE_STYLE ('',( #99481 ) ) ; +#37321 = VECTOR ( 'NONE', #52572, 999.9999999999998863 ) ; +#37322 = ADVANCED_FACE ( 'NONE', ( #90844 ), #36234, .T. ) ; +#37323 = AXIS2_PLACEMENT_3D ( 'NONE', #73753, #12386, #34976 ) ; +#37324 = VECTOR ( 'NONE', #51900, 1000.000000000000000 ) ; +#37325 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66674, 'distance_accuracy_value', 'NONE'); +#37326 = ORIENTED_EDGE ( 'NONE', *, *, #42455, .T. ) ; +#37327 = LINE ( 'NONE', #13756, #32925 ) ; +#37328 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37329 = STYLED_ITEM ( 'NONE', ( #59238 ), #5992 ) ; +#37330 = FILL_AREA_STYLE_COLOUR ( '', #38415 ) ; +#37331 = PLANE ( 'NONE', #89209 ) ; +#37332 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37333 = SURFACE_SIDE_STYLE ('',( #20469 ) ) ; +#37334 = VECTOR ( 'NONE', #65810, 1000.000000000000000 ) ; +#37335 = PLANE ( 'NONE', #49208 ) ; +#37336 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#37337 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37338 = EDGE_CURVE ( 'NONE', #23403, #77944, #26367, .T. ) ; +#37339 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#37340 = VECTOR ( 'NONE', #85022, 1000.000000000000000 ) ; +#37341 = VECTOR ( 'NONE', #30757, 1000.000000000000000 ) ; +#37342 = VERTEX_POINT ( 'NONE', #14178 ) ; +#37343 = FILL_AREA_STYLE ('',( #8087 ) ) ; +#37344 = ORIENTED_EDGE ( 'NONE', *, *, #30004, .F. ) ; +#37345 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25983 ) ) ; +#37346 = FILL_AREA_STYLE_COLOUR ( '', #8013 ) ; +#37347 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#37349 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14459 ) ) ; +#37348 = CARTESIAN_POINT ( 'NONE', ( -0.1522818774044870371, -0.9679977428869791511, 0.8100000000000000533 ) ) ; +#37350 = PLANE ( 'NONE', #99841 ) ; +#37351 = SURFACE_STYLE_FILL_AREA ( #76125 ) ; +#37352 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37353 = SURFACE_STYLE_FILL_AREA ( #83802 ) ; +#37354 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999995004, 0.8200000000000000622, -0.04999999999999997502 ) ) ; +#37355 = AXIS2_PLACEMENT_3D ( 'NONE', #88891, #59294, #5085 ) ; +#37356 = VERTEX_POINT ( 'NONE', #68344 ) ; +#37357 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37358 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37359 = ORIENTED_EDGE ( 'NONE', *, *, #70513, .F. ) ; +#37360 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37361 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#37362 = ORIENTED_EDGE ( 'NONE', *, *, #13597, .T. ) ; +#37363 = FACE_OUTER_BOUND ( 'NONE', #91957, .T. ) ; +#37364 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#37365 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.800000000000000711, 0.000000000000000000 ) ) ; +#37366 = EDGE_CURVE ( 'NONE', #20041, #67209, #15712, .T. ) ; +#37367 = SURFACE_SIDE_STYLE ('',( #76141 ) ) ; +#37368 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#37370 = EDGE_LOOP ( 'NONE', ( #57398, #49557, #39143, #99521 ) ) ; +#37369 = ORIENTED_EDGE ( 'NONE', *, *, #98807, .F. ) ; +#37372 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38953 ) ) ; +#37371 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999986226, 0.1400000000000000133 ) ) ; +#37373 = ORIENTED_EDGE ( 'NONE', *, *, #18999, .T. ) ; +#37375 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#37374 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37376 = ORIENTED_EDGE ( 'NONE', *, *, #45560, .T. ) ; +#37377 = EDGE_CURVE ( 'NONE', #91502, #87470, #92326, .T. ) ; +#37378 = ORIENTED_EDGE ( 'NONE', *, *, #48913, .F. ) ; +#37379 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37380 = LINE ( 'NONE', #76658, #69782 ) ; +#37381 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4695 ) ) ; +#37383 = FILL_AREA_STYLE ('',( #44985 ) ) ; +#37382 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37384 = ORIENTED_EDGE ( 'NONE', *, *, #16917, .F. ) ; +#37385 = EDGE_LOOP ( 'NONE', ( #28764, #46623, #74470, #86462, #36651, #46730 ) ) ; +#37386 = FACE_OUTER_BOUND ( 'NONE', #50234, .T. ) ; +#37387 = EDGE_LOOP ( 'NONE', ( #19135, #823, #92322, #8695, #50683, #79196, #6045, #29462, #350, #40522 ) ) ; +#37388 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2750000000000000222, 0.1500000000000000500 ) ) ; +#37389 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83073 ), #100847 ) ; +#37390 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60216 ) ) ; +#37391 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37392 = ORIENTED_EDGE ( 'NONE', *, *, #95131, .F. ) ; +#37393 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63735 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65451, #5142, #97575 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37394 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34130 ) ) ; +#37395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#37396 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37397 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37398 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37399 = EDGE_LOOP ( 'NONE', ( #43877, #84283 ) ) ; +#37400 = VECTOR ( 'NONE', #2916, 1000.000000000000114 ) ; +#37401 = FILL_AREA_STYLE_COLOUR ( '', #85881 ) ; +#37402 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, -0.7999999999999999334 ) ) ; +#37403 = ORIENTED_EDGE ( 'NONE', *, *, #21775, .T. ) ; +#37404 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37405 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #21891, #91339, #85171, #70348 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37406 = EDGE_CURVE ( 'NONE', #24157, #5920, #37405, .T. ) ; +#37407 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65685 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36613, #60119, #52426 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37408 = FILL_AREA_STYLE ('',( #76179 ) ) ; +#37409 = STYLED_ITEM ( 'NONE', ( #1121 ), #80450 ) ; +#37410 = ADVANCED_FACE ( 'NONE', ( #37725 ), #31061, .T. ) ; +#37412 = ORIENTED_EDGE ( 'NONE', *, *, #11837, .T. ) ; +#37411 = LINE ( 'NONE', #12317, #86775 ) ; +#37413 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.123820061220045297, -0.02000000000000000042 ) ) ; +#37414 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#37416 = SURFACE_STYLE_USAGE ( .BOTH. , #51225 ) ; +#37415 = PLANE ( 'NONE', #77354 ) ; +#37417 = VECTOR ( 'NONE', #95548, 1000.000000000000000 ) ; +#37418 = VECTOR ( 'NONE', #484, 1000.000000000000000 ) ; +#37419 = ORIENTED_EDGE ( 'NONE', *, *, #94797, .T. ) ; +#37420 = FILL_AREA_STYLE ('',( #77188 ) ) ; +#37422 = CARTESIAN_POINT ( 'NONE', ( 1.639423674598250003, -1.436594792639700024, 0.8100000000000000533 ) ) ; +#37421 = CARTESIAN_POINT ( 'NONE', ( 0.4538094727981990539, -1.016713352587220065, 0.8299999999999999600 ) ) ; +#37423 = LINE ( 'NONE', #44047, #76290 ) ; +#37424 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37425 = ADVANCED_FACE ( 'NONE', ( #83690 ), #91818, .T. ) ; +#37426 = PRESENTATION_STYLE_ASSIGNMENT (( #13855 ) ) ; +#37427 = EDGE_CURVE ( 'NONE', #42677, #30261, #412, .T. ) ; +#37428 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#37429 = ORIENTED_EDGE ( 'NONE', *, *, #47216, .F. ) ; +#37430 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#37431 = AXIS2_PLACEMENT_3D ( 'NONE', #27685, #13768, #82299 ) ; +#37432 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#37433 = ORIENTED_EDGE ( 'NONE', *, *, #15744, .T. ) ; +#37434 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37436 = LINE ( 'NONE', #84860, #59194 ) ; +#37435 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#37437 = SURFACE_STYLE_FILL_AREA ( #82393 ) ; +#37438 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37439 = EDGE_CURVE ( 'NONE', #49190, #10657, #86179, .T. ) ; +#37440 = FILL_AREA_STYLE ('',( #74223 ) ) ; +#37441 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37442 = ORIENTED_EDGE ( 'NONE', *, *, #63204, .F. ) ; +#37443 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37444 = LINE ( 'NONE', #6689, #16850 ) ; +#37445 = DIRECTION ( 'NONE', ( -0.9390355371548172458, 0.000000000000000000, -0.3438200982495990821 ) ) ; +#37446 = FILL_AREA_STYLE ('',( #37927 ) ) ; +#37447 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37448 = PRESENTATION_STYLE_ASSIGNMENT (( #68042 ) ) ; +#37449 = VECTOR ( 'NONE', #37958, 1000.000000000000227 ) ; +#37450 = SURFACE_SIDE_STYLE ('',( #74735 ) ) ; +#37451 = SURFACE_SIDE_STYLE ('',( #91548 ) ) ; +#37452 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #35422, #91011 ), + ( #68001, #89998 ), + ( #99077, #97625 ), + ( #35909, #67022 ), + ( #13839, #98096 ), + ( #76187, #6177 ), + ( #29717, #60897 ), + ( #38403, #31231 ), + ( #7157, #39910 ), + ( #24105, #55255 ), + ( #85344, #47049 ), + ( #84838, #77182 ), + ( #30705, #47559 ), + ( #93483, #86367 ), + ( #54224, #15378 ), + ( #62399, #24631 ), + ( #45502, #69507 ), + ( #92490, #32257 ), + ( #16377, #78 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07134662578984279913, 0.1388341252834479900, 0.2038682582026460077, 0.2661788482005160161, 0.3265850789285990041, 0.3849791193600949901, 0.4422744752917839861, 0.4992876152042279858, 0.5564569914632400138, 0.6143100800959649943, 0.6731214209110579771, 0.7340520381337829470, 0.7970235749488939758, 0.8619020797931600253, 0.9293895792867660210, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37453 = FILL_AREA_STYLE_COLOUR ( '', #57477 ) ; +#37454 = EDGE_CURVE ( 'NONE', #8279, #44266, #40754, .T. ) ; +#37455 = VECTOR ( 'NONE', #75192, 1000.000000000000000 ) ; +#37456 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11034 ) ) ; +#37457 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37458 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#37459 = ORIENTED_EDGE ( 'NONE', *, *, #85618, .T. ) ; +#37460 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37461 = ORIENTED_EDGE ( 'NONE', *, *, #33134, .T. ) ; +#37462 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37463 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#37464 = STYLED_ITEM ( 'NONE', ( #47258 ), #85185 ) ; +#37465 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496381000000000405, 0.8648700000000000276 ) ) ; +#37466 = CARTESIAN_POINT ( 'NONE', ( 1.783955832751769943, -0.9153515042605530061, 0.8100000000000000533 ) ) ; +#37467 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#37468 = FILL_AREA_STYLE_COLOUR ( '', #22782 ) ; +#37469 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58696 ), #12883 ) ; +#37470 = LINE ( 'NONE', #91563, #42838 ) ; +#37471 = EDGE_LOOP ( 'NONE', ( #76300, #73217, #35005, #3584 ) ) ; +#37472 = SURFACE_STYLE_FILL_AREA ( #61466 ) ; +#37473 = AXIS2_PLACEMENT_3D ( 'NONE', #34498, #65602, #96718 ) ; +#37474 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01085786437626906978, 0.2399999999999999911 ) ) ; +#37475 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #17933, #51140, #65953, #3652, #10197, #18449, #11221, #73104, #88417, #25640, #89422, #41466, #27163, #96549, #33302, #49635, #50647, #26151, #3152 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.579034425011788966E-05, 3.081603604639139435E-05, 4.491746013560603994E-05, 5.837560011015461268E-05, 7.117912044677800307E-05, 8.376220332115868529E-05, 9.603306182116576090E-05, 0.0001083585251528225630, 0.0001207930788422280279, 0.0001333113597912686350, 0.0001461759257520239916, 0.0001592721489571428603, 0.0001728423707183345665, 0.0001868402333759962286, 0.0002015609050938724776, 0.0002168387333276463962 ), + .UNSPECIFIED. ) ; +#37476 = ORIENTED_EDGE ( 'NONE', *, *, #18868, .F. ) ; +#37477 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37478 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37479 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 9.949999999999999289, 0.000000000000000000 ) ) ; +#37480 = EDGE_CURVE ( 'NONE', #40707, #35876, #2450, .T. ) ; +#37481 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4797 ), #97757 ) ; +#37482 = CARTESIAN_POINT ( 'NONE', ( -1.294533524454640094, -1.379057077391790287, 0.8299999999999999600 ) ) ; +#37483 = SURFACE_STYLE_FILL_AREA ( #75274 ) ; +#37484 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#37485 = EDGE_LOOP ( 'NONE', ( #91439, #63392, #82609, #72407 ) ) ; +#37486 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722700000000096, 0.8991599999999999593 ) ) ; +#37487 = VECTOR ( 'NONE', #70396, 1000.000000000000000 ) ; +#37488 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37489 = VECTOR ( 'NONE', #97771, 1000.000000000000000 ) ; +#37490 = FACE_OUTER_BOUND ( 'NONE', #50326, .T. ) ; +#37491 = CARTESIAN_POINT ( 'NONE', ( 2.706044754058724855E-34, 1.771815017538448318E-34, 0.8648700000000000276 ) ) ; +#37492 = EDGE_CURVE ( 'NONE', #2971, #42643, #71373, .T. ) ; +#37493 = ORIENTED_EDGE ( 'NONE', *, *, #13185, .F. ) ; +#37494 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#37495 = FILL_AREA_STYLE_COLOUR ( '', #80439 ) ; +#37496 = STYLED_ITEM ( 'NONE', ( #32667 ), #51179 ) ; +#37497 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#37498 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37499 = ORIENTED_EDGE ( 'NONE', *, *, #42005, .T. ) ; +#37500 = FILL_AREA_STYLE ('',( #76778 ) ) ; +#37501 = VECTOR ( 'NONE', #50151, 1000.000000000000114 ) ; +#37502 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99096, 'distance_accuracy_value', 'NONE'); +#37503 = EDGE_LOOP ( 'NONE', ( #57875, #1186, #97946, #48214 ) ) ; +#37504 = ORIENTED_EDGE ( 'NONE', *, *, #73956, .T. ) ; +#37505 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51708, 'distance_accuracy_value', 'NONE'); +#37506 = PRESENTATION_STYLE_ASSIGNMENT (( #6278 ) ) ; +#37508 = CARTESIAN_POINT ( 'NONE', ( -1.241916755955269958, -1.502675929081449979, 0.8100000000000000533 ) ) ; +#37507 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#37509 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#37510 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -1.355252715606876105E-16 ) ) ; +#37511 = VERTEX_POINT ( 'NONE', #95839 ) ; +#37512 = PRESENTATION_STYLE_ASSIGNMENT (( #67602 ) ) ; +#37513 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37514 = SURFACE_STYLE_USAGE ( .BOTH. , #12426 ) ; +#37515 = VERTEX_POINT ( 'NONE', #33600 ) ; +#37516 = FILL_AREA_STYLE_COLOUR ( '', #56204 ) ; +#37517 = LINE ( 'NONE', #61005, #17098 ) ; +#37518 = STYLED_ITEM ( 'NONE', ( #51677 ), #33241 ) ; +#37519 = VERTEX_POINT ( 'NONE', #55590 ) ; +#37521 = PRESENTATION_STYLE_ASSIGNMENT (( #21174 ) ) ; +#37520 = CARTESIAN_POINT ( 'NONE', ( 1.708426850688339771, -1.163903542943879987, 0.8099999999999998312 ) ) ; +#37522 = ORIENTED_EDGE ( 'NONE', *, *, #87919, .T. ) ; +#37523 = ADVANCED_FACE ( 'NONE', ( #79554 ), #47387, .T. ) ; +#37524 = EDGE_CURVE ( 'NONE', #51624, #47557, #9996, .T. ) ; +#37525 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37526 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81635 ) ) ; +#37527 = VECTOR ( 'NONE', #75588, 1000.000000000000000 ) ; +#37528 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#37529 = FILL_AREA_STYLE ('',( #13444 ) ) ; +#37530 = CARTESIAN_POINT ( 'NONE', ( 0.1743057588777000011, -1.390658178011239920, 0.8299999999999982947 ) ) ; +#37531 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91302 ) ) ; +#37532 = ORIENTED_EDGE ( 'NONE', *, *, #11732, .T. ) ; +#37533 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.000000000000000000 ) ) ; +#37534 = ORIENTED_EDGE ( 'NONE', *, *, #78700, .F. ) ; +#37536 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#37535 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34279 ) ) ; +#37537 = FACE_OUTER_BOUND ( 'NONE', #79832, .T. ) ; +#37538 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37539 = EDGE_CURVE ( 'NONE', #63825, #42447, #64721, .T. ) ; +#37540 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89173 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62487, #15975, #47140 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37541 = EDGE_CURVE ( 'NONE', #21155, #71240, #34871, .T. ) ; +#37542 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66836 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63817, #17312, #3540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37543 = VECTOR ( 'NONE', #38803, 1000.000000000000000 ) ; +#37544 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37545 = SURFACE_STYLE_USAGE ( .BOTH. , #43660 ) ; +#37546 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37547 = FILL_AREA_STYLE ('',( #45643 ) ) ; +#37548 = ORIENTED_EDGE ( 'NONE', *, *, #87782, .F. ) ; +#37549 = PLANE ( 'NONE', #31811 ) ; +#37550 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40839 ), #50620 ) ; +#37552 = LINE ( 'NONE', #69122, #77067 ) ; +#37551 = SURFACE_STYLE_FILL_AREA ( #15519 ) ; +#37553 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32829, 'distance_accuracy_value', 'NONE'); +#37554 = VECTOR ( 'NONE', #945, 1000.000000000000000 ) ; +#37555 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37556 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16290 ), #11369 ) ; +#37557 = LINE ( 'NONE', #21209, #74018 ) ; +#37558 = ADVANCED_FACE ( 'NONE', ( #72893 ), #64444, .F. ) ; +#37559 = LINE ( 'NONE', #61050, #69003 ) ; +#37560 = ORIENTED_EDGE ( 'NONE', *, *, #1213, .T. ) ; +#37561 = SURFACE_STYLE_USAGE ( .BOTH. , #53870 ) ; +#37563 = EDGE_CURVE ( 'NONE', #2708, #55587, #30935, .T. ) ; +#37562 = SURFACE_SIDE_STYLE ('',( #29386 ) ) ; +#37564 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#37565 = CARTESIAN_POINT ( 'NONE', ( 0.01310978785461489916, -1.357122040133029950, 0.8100000000000000533 ) ) ; +#37566 = STYLED_ITEM ( 'NONE', ( #70895 ), #10811 ) ; +#37567 = PRESENTATION_STYLE_ASSIGNMENT (( #83520 ) ) ; +#37568 = LINE ( 'NONE', #45671, #7234 ) ; +#37569 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17988 ) ) ; +#37570 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37571 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37572 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#37573 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23104, #54774, #77198, #70039 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37574 = SURFACE_SIDE_STYLE ('',( #6346 ) ) ; +#37575 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#37576 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#37577 = EDGE_CURVE ( 'NONE', #98421, #67944, #83570, .T. ) ; +#37578 = FILL_AREA_STYLE ('',( #29878 ) ) ; +#37579 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37580 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37581 = SURFACE_STYLE_USAGE ( .BOTH. , #43698 ) ; +#37582 = ADVANCED_FACE ( 'NONE', ( #91700 ), #100754, .F. ) ; +#37583 = LINE ( 'NONE', #29882, #92597 ) ; +#37584 = LINE ( 'NONE', #45183, #36633 ) ; +#37585 = AXIS2_PLACEMENT_3D ( 'NONE', #33722, #88331, #65338 ) ; +#37586 = ADVANCED_FACE ( 'NONE', ( #21769 ), #52937, .F. ) ; +#37587 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#37588 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37589 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37590 = SURFACE_STYLE_FILL_AREA ( #52912 ) ; +#37591 = ORIENTED_EDGE ( 'NONE', *, *, #56764, .F. ) ; +#37592 = SURFACE_STYLE_USAGE ( .BOTH. , #44703 ) ; +#37593 = PRESENTATION_STYLE_ASSIGNMENT (( #30377 ) ) ; +#37594 = FILL_AREA_STYLE_COLOUR ( '', #46092 ) ; +#37595 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81629 ), #42475 ) ; +#37596 = CARTESIAN_POINT ( 'NONE', ( -0.1025235689449880000, -0.9625006208768249749, 0.8300000000000002931 ) ) ; +#37597 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37598 = STYLED_ITEM ( 'NONE', ( #39136 ), #93553 ) ; +#37599 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37600 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#37601 = EDGE_CURVE ( 'NONE', #76167, #91965, #14567, .T. ) ; +#37602 = CARTESIAN_POINT ( 'NONE', ( 10.38419899999999885, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#37603 = FILL_AREA_STYLE_COLOUR ( '', #47337 ) ; +#37604 = ORIENTED_EDGE ( 'NONE', *, *, #90894, .F. ) ; +#37605 = PLANE ( 'NONE', #26998 ) ; +#37607 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37606 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37608 = VECTOR ( 'NONE', #57786, 1000.000000000000000 ) ; +#37609 = STYLED_ITEM ( 'NONE', ( #17866 ), #81794 ) ; +#37610 = ADVANCED_FACE ( 'NONE', ( #14061 ), #45712, .T. ) ; +#37611 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#37612 = ORIENTED_EDGE ( 'NONE', *, *, #47279, .T. ) ; +#37613 = ORIENTED_EDGE ( 'NONE', *, *, #37639, .F. ) ; +#37614 = PLANE ( 'NONE', #34134 ) ; +#37615 = ORIENTED_EDGE ( 'NONE', *, *, #73971, .T. ) ; +#37616 = CARTESIAN_POINT ( 'NONE', ( 0.08972571571753010233, -1.370875895369189967, 0.8100000000000000533 ) ) ; +#37617 = EDGE_CURVE ( 'NONE', #79695, #73310, #15065, .T. ) ; +#37618 = CARTESIAN_POINT ( 'NONE', ( 0.5106752425455549638, -1.185737326210950071, 0.8100000000000000533 ) ) ; +#37619 = FACE_OUTER_BOUND ( 'NONE', #19546, .T. ) ; +#37620 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37621 = CARTESIAN_POINT ( 'NONE', ( 0.2416947311349459948, -1.083527867505859943, 0.8100000000000000533 ) ) ; +#37622 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37623 = VERTEX_POINT ( 'NONE', #32467 ) ; +#37624 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89790 ) ) ; +#37625 = AXIS2_PLACEMENT_3D ( 'NONE', #95729, #64626, #64134 ) ; +#37626 = ORIENTED_EDGE ( 'NONE', *, *, #38769, .T. ) ; +#37627 = PRESENTATION_STYLE_ASSIGNMENT (( #21779 ) ) ; +#37628 = LINE ( 'NONE', #68718, #26451 ) ; +#37629 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93978, 'distance_accuracy_value', 'NONE'); +#37631 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37630 = FILL_AREA_STYLE ('',( #7385 ) ) ; +#37632 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#37633 = VECTOR ( 'NONE', #100339, 1000.000000000000000 ) ; +#37634 = VERTEX_POINT ( 'NONE', #24325 ) ; +#37636 = CARTESIAN_POINT ( 'NONE', ( -0.7996373468737240087, 0.5991788043593869739, 0.8100000000000000533 ) ) ; +#37635 = SURFACE_STYLE_FILL_AREA ( #68731 ) ; +#37637 = ORIENTED_EDGE ( 'NONE', *, *, #89200, .F. ) ; +#37638 = ORIENTED_EDGE ( 'NONE', *, *, #41440, .F. ) ; +#37639 = EDGE_CURVE ( 'NONE', #86902, #14330, #87091, .T. ) ; +#37640 = CARTESIAN_POINT ( 'NONE', ( 1.316661513406260031, -1.260670644472420054, 0.8299999999999999600 ) ) ; +#37642 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37641 = PLANE ( 'NONE', #16854 ) ; +#37643 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#37644 = ORIENTED_EDGE ( 'NONE', *, *, #43513, .F. ) ; +#37645 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#37646 = LINE ( 'NONE', #53470, #29021 ) ; +#37647 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37648 = EDGE_LOOP ( 'NONE', ( #30469, #1460, #96562, #46858, #37429, #90431 ) ) ; +#37649 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#37650 = LINE ( 'NONE', #77947, #67402 ) ; +#37651 = ORIENTED_EDGE ( 'NONE', *, *, #39284, .T. ) ; +#37652 = ORIENTED_EDGE ( 'NONE', *, *, #20270, .T. ) ; +#37653 = CARTESIAN_POINT ( 'NONE', ( 1.015677417745509903, -1.448219210431749948, 0.8299999999999999600 ) ) ; +#37654 = SURFACE_STYLE_USAGE ( .BOTH. , #67760 ) ; +#37655 = SURFACE_STYLE_FILL_AREA ( #22313 ) ; +#37656 = SURFACE_SIDE_STYLE ('',( #36167 ) ) ; +#37657 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68596 ), #9864 ) ; +#37658 = CARTESIAN_POINT ( 'NONE', ( -1.201345065735160977, -0.9556482860497677034, 0.8100000000000203704 ) ) ; +#37659 = EDGE_CURVE ( 'NONE', #49717, #68649, #73800, .T. ) ; +#37660 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37661 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #7504 ) ; +#37662 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37663 = VECTOR ( 'NONE', #48716, 1000.000000000000000 ) ; +#37664 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4633 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66147, #58531, #11928 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37665 = VECTOR ( 'NONE', #47219, 1000.000000000000000 ) ; +#37666 = ORIENTED_EDGE ( 'NONE', *, *, #88790, .F. ) ; +#37667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37668 = VERTEX_POINT ( 'NONE', #24836 ) ; +#37669 = FACE_OUTER_BOUND ( 'NONE', #69721, .T. ) ; +#37671 = FILL_AREA_STYLE_COLOUR ( '', #28562 ) ; +#37670 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37672 = CYLINDRICAL_SURFACE ( 'NONE', #76136, 0.09999999999999939493 ) ; +#37673 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73536 ) ) ; +#37674 = CARTESIAN_POINT ( 'NONE', ( 11.95397624975002770, 5.528756750249976371, 0.8991599999999999593 ) ) ; +#37675 = VECTOR ( 'NONE', #83992, 1000.000000000000114 ) ; +#37676 = SURFACE_STYLE_FILL_AREA ( #91276 ) ; +#37677 = PLANE ( 'NONE', #22314 ) ; +#37678 = SURFACE_STYLE_USAGE ( .BOTH. , #91278 ) ; +#37679 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#37680 = ORIENTED_EDGE ( 'NONE', *, *, #18275, .T. ) ; +#37681 = VECTOR ( 'NONE', #40009, 1000.000000000000000 ) ; +#37682 = EDGE_CURVE ( 'NONE', #31741, #88747, #8372, .T. ) ; +#37683 = SURFACE_STYLE_USAGE ( .BOTH. , #6458 ) ; +#37684 = FACE_OUTER_BOUND ( 'NONE', #935, .T. ) ; +#37685 = PRESENTATION_STYLE_ASSIGNMENT (( #6460 ) ) ; +#37686 = AXIS2_PLACEMENT_3D ( 'NONE', #52273, #3782, #74737 ) ; +#37687 = CARTESIAN_POINT ( 'NONE', ( 1.850801046367029912, -1.212495751768599916, 0.8299999999999999600 ) ) ; +#37688 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37689 = EDGE_CURVE ( 'NONE', #38594, #55276, #40129, .T. ) ; +#37690 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#37691 = LINE ( 'NONE', #85133, #85868 ) ; +#37692 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37693 = EDGE_CURVE ( 'NONE', #10511, #31497, #39106, .T. ) ; +#37694 = SURFACE_STYLE_USAGE ( .BOTH. , #6468 ) ; +#37695 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37696 = STYLED_ITEM ( 'NONE', ( #64883 ), #69529 ) ; +#37697 = SURFACE_STYLE_FILL_AREA ( #6473 ) ; +#37698 = PRESENTATION_STYLE_ASSIGNMENT (( #92298 ) ) ; +#37699 = CARTESIAN_POINT ( 'NONE', ( -0.9368726506143657540, -1.046522010761834043, 0.8099999999999538680 ) ) ; +#37700 = VERTEX_POINT ( 'NONE', #8879 ) ; +#37701 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#37702 = SURFACE_STYLE_FILL_AREA ( #84155 ) ; +#37703 = CARTESIAN_POINT ( 'NONE', ( 1.651684746960339956, -1.440618065759700084, 0.8299999999999977396 ) ) ; +#37704 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56324 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33567, #25906, #41719 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37705 = LINE ( 'NONE', #52524, #85033 ) ; +#37706 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37707 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 1.100000000000000311, -0.02000000000000000042 ) ) ; +#37708 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45579 ), #50561 ) ; +#37709 = EDGE_CURVE ( 'NONE', #39620, #92147, #16095, .T. ) ; +#37710 = VERTEX_POINT ( 'NONE', #25825 ) ; +#37711 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980549, 0.000000000000000000 ) ) ; +#37712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37713 = FILL_AREA_STYLE_COLOUR ( '', #26925 ) ; +#37714 = PRESENTATION_STYLE_ASSIGNMENT (( #91328 ) ) ; +#37715 = SURFACE_SIDE_STYLE ('',( #91329 ) ) ; +#37716 = LINE ( 'NONE', #85161, #59241 ) ; +#37717 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37718 = EDGE_CURVE ( 'NONE', #77757, #81104, #63117, .T. ) ; +#37719 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37720 = ORIENTED_EDGE ( 'NONE', *, *, #34444, .T. ) ; +#37721 = ORIENTED_EDGE ( 'NONE', *, *, #82939, .F. ) ; +#37722 = VECTOR ( 'NONE', #18493, 1000.000000000000000 ) ; +#37723 = PRESENTATION_STYLE_ASSIGNMENT (( #45337 ) ) ; +#37724 = ORIENTED_EDGE ( 'NONE', *, *, #52145, .F. ) ; +#37725 = FACE_OUTER_BOUND ( 'NONE', #86862, .T. ) ; +#37726 = ADVANCED_FACE ( 'NONE', ( #54954 ), #32967, .T. ) ; +#37727 = LINE ( 'NONE', #29064, #46929 ) ; +#37728 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37729 = FACE_OUTER_BOUND ( 'NONE', #68341, .T. ) ; +#37730 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86702 ) ) ; +#37731 = SHAPE_DEFINITION_REPRESENTATION ( #72592, #23337 ) ; +#37732 = LINE ( 'NONE', #77023, #37794 ) ; +#37733 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #17369, #48555, #29512, #61188 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37735 = VERTEX_POINT ( 'NONE', #1828 ) ; +#37734 = VERTEX_POINT ( 'NONE', #2339 ) ; +#37736 = EDGE_CURVE ( 'NONE', #65615, #29642, #16594, .T. ) ; +#37737 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3496 ), #73598 ) ; +#37738 = ORIENTED_EDGE ( 'NONE', *, *, #16332, .T. ) ; +#37739 = FILL_AREA_STYLE ('',( #6516 ) ) ; +#37740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27287, 'distance_accuracy_value', 'NONE'); +#37741 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.2999999999999989897, 5.981926231290386527E-79 ) ) ; +#37743 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37742 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37744 = EDGE_LOOP ( 'NONE', ( #12274, #19960, #55380, #36481 ) ) ; +#37745 = EDGE_CURVE ( 'NONE', #71570, #83515, #47778, .T. ) ; +#37746 = VERTEX_POINT ( 'NONE', #9398 ) ; +#37747 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37748 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37751 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8648700000000000276 ) ) ; +#37750 = AXIS2_PLACEMENT_3D ( 'NONE', #3918, #93899, #39838 ) ; +#37749 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#37752 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89059 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1662, #9220, #3155 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37753 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691640, 0.4849999999999999867, -0.2458578643762689975 ) ) ; +#37754 = ORIENTED_EDGE ( 'NONE', *, *, #70468, .F. ) ; +#37755 = CARTESIAN_POINT ( 'NONE', ( -0.4444315888559909888, -1.066522886050349950, 0.8100000000000000533 ) ) ; +#37756 = VERTEX_POINT ( 'NONE', #40635 ) ; +#37757 = EDGE_CURVE ( 'NONE', #40138, #88846, #72263, .T. ) ; +#37758 = VERTEX_POINT ( 'NONE', #87587 ) ; +#37759 = ADVANCED_FACE ( 'NONE', ( #48809 ), #72777, .T. ) ; +#37760 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#37763 = ADVANCED_FACE ( 'NONE', ( #35002 ), #57996, .T. ) ; +#37762 = ORIENTED_EDGE ( 'NONE', *, *, #91489, .T. ) ; +#37761 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37764 = EDGE_CURVE ( 'NONE', #36447, #26091, #20133, .T. ) ; +#37765 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.5199999999376814230, 0.000000000000000000 ) ) ; +#37766 = VERTEX_POINT ( 'NONE', #26324 ) ; +#37767 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37768 = ORIENTED_EDGE ( 'NONE', *, *, #78793, .F. ) ; +#37769 = ORIENTED_EDGE ( 'NONE', *, *, #49495, .F. ) ; +#37770 = SURFACE_STYLE_USAGE ( .BOTH. , #54092 ) ; +#37771 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #46611, #38974, #23660, #22649 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#37772 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 4.418599000000000387, 0.8648700000000000276 ) ) ; +#37773 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000009992, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#37774 = EDGE_CURVE ( 'NONE', #48692, #85879, #89103, .T. ) ; +#37775 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11234 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7327, #47729, #70702 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37776 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999989875, 0.000000000000000000 ) ) ; +#37777 = LINE ( 'NONE', #30570, #42901 ) ; +#37778 = ADVANCED_FACE ( 'NONE', ( #58995 ), #97228, .T. ) ; +#37779 = SURFACE_SIDE_STYLE ('',( #92840 ) ) ; +#37780 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#37781 = FILL_AREA_STYLE ('',( #21437 ) ) ; +#37782 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37783 = EDGE_LOOP ( 'NONE', ( #92479, #36743, #84285, #27519 ) ) ; +#37784 = SURFACE_SIDE_STYLE ('',( #76069 ) ) ; +#37785 = CARTESIAN_POINT ( 'NONE', ( -1.125815218778140059, -1.515241174392790047, 0.8100000000000000533 ) ) ; +#37786 = ORIENTED_EDGE ( 'NONE', *, *, #81813, .F. ) ; +#37787 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000009992, -3.123820061220065281, 0.000000000000000000 ) ) ; +#37788 = PRESENTATION_STYLE_ASSIGNMENT (( #22452 ) ) ; +#37789 = PRESENTATION_STYLE_ASSIGNMENT (( #36298 ) ) ; +#37790 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37791 = CYLINDRICAL_SURFACE ( 'NONE', #25230, 0.009999999999999998473 ) ; +#37792 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#37793 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37794 = VECTOR ( 'NONE', #22923, 1000.000000000000000 ) ; +#37795 = FILL_AREA_STYLE_COLOUR ( '', #16965 ) ; +#37796 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37797 = FACE_OUTER_BOUND ( 'NONE', #75983, .T. ) ; +#37798 = SURFACE_STYLE_FILL_AREA ( #6580 ) ; +#37799 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37801 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#37800 = SURFACE_STYLE_FILL_AREA ( #37317 ) ; +#37802 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.000000000000000000 ) ) ; +#37803 = EDGE_CURVE ( 'NONE', #5274, #93048, #46093, .T. ) ; +#37804 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52460 ) ) ; +#37805 = FILL_AREA_STYLE_COLOUR ( '', #15862 ) ; +#37806 = STYLED_ITEM ( 'NONE', ( #84978 ), #8375 ) ; +#37807 = AXIS2_PLACEMENT_3D ( 'NONE', #80975, #10907, #809 ) ; +#37808 = EDGE_CURVE ( 'NONE', #36233, #70651, #22148, .T. ) ; +#37809 = ORIENTED_EDGE ( 'NONE', *, *, #97634, .T. ) ; +#37810 = CARTESIAN_POINT ( 'NONE', ( -1.061635297135890221, -1.433733517242619993, 0.8100000000000000533 ) ) ; +#37811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75341 ) ) ; +#37812 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86129, 'distance_accuracy_value', 'NONE'); +#37813 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19850, 'distance_accuracy_value', 'NONE'); +#37814 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37815 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37816 = SURFACE_SIDE_STYLE ('',( #7073 ) ) ; +#37817 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#37818 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37819 = VECTOR ( 'NONE', #46968, 1000.000000000000000 ) ; +#37820 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#37821 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#37822 = ORIENTED_EDGE ( 'NONE', *, *, #70204, .F. ) ; +#37823 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37824 = ADVANCED_FACE ( 'NONE', ( #36496 ), #91098, .F. ) ; +#37825 = VERTEX_POINT ( 'NONE', #53801 ) ; +#37826 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000001332, -0.2400000000000000189 ) ) ; +#37827 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68454, 'distance_accuracy_value', 'NONE'); +#37828 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14405, 'distance_accuracy_value', 'NONE'); +#37829 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8648700000000000276 ) ) ; +#37830 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#37831 = SURFACE_SIDE_STYLE ('',( #91937 ) ) ; +#37832 = CARTESIAN_POINT ( 'NONE', ( -0.2389181574176280354, -1.341601374162270099, 0.8299999999999995159 ) ) ; +#37833 = LINE ( 'NONE', #98514, #87634 ) ; +#37834 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37835 = SURFACE_SIDE_STYLE ('',( #62339 ) ) ; +#37836 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99663 ), #14960 ) ; +#37837 = ORIENTED_EDGE ( 'NONE', *, *, #11993, .F. ) ; +#37838 = FACE_OUTER_BOUND ( 'NONE', #60725, .T. ) ; +#37840 = EDGE_CURVE ( 'NONE', #47262, #51794, #77267, .T. ) ; +#37839 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37841 = ORIENTED_EDGE ( 'NONE', *, *, #59902, .T. ) ; +#37842 = PRESENTATION_STYLE_ASSIGNMENT (( #98039 ) ) ; +#37843 = ORIENTED_EDGE ( 'NONE', *, *, #87563, .T. ) ; +#37844 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37845 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#37846 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37847 = FILL_AREA_STYLE ('',( #537 ) ) ; +#37848 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, 3.099999999999992095, 0.000000000000000000 ) ) ; +#37849 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#37851 = ORIENTED_EDGE ( 'NONE', *, *, #44576, .T. ) ; +#37850 = ORIENTED_EDGE ( 'NONE', *, *, #99846, .T. ) ; +#37852 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68814 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62625, #38121, #53935 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#37853 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83556 ) ) ; +#37854 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8648700000000000276 ) ) ; +#37855 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37856 = EDGE_LOOP ( 'NONE', ( #66107, #89925, #20511, #55719 ) ) ; +#37857 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37859 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#37858 = SURFACE_SIDE_STYLE ('',( #6632 ) ) ; +#37860 = ORIENTED_EDGE ( 'NONE', *, *, #23821, .F. ) ; +#37861 = ORIENTED_EDGE ( 'NONE', *, *, #83770, .T. ) ; +#37862 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37863 = AXIS2_PLACEMENT_3D ( 'NONE', #48376, #40189, #17169 ) ; +#37864 = AXIS2_PLACEMENT_3D ( 'NONE', #674, #69600, #61491 ) ; +#37865 = CARTESIAN_POINT ( 'NONE', ( -0.4939079156693390038, -1.173538053626689948, 0.8299999999999999600 ) ) ; +#37866 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#37868 = SURFACE_SIDE_STYLE ('',( #100514 ) ) ; +#37867 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37869 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#37870 = VERTEX_POINT ( 'NONE', #21649 ) ; +#37871 = VERTEX_POINT ( 'NONE', #99645 ) ; +#37872 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37873 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#37874 = VERTEX_POINT ( 'NONE', #21151 ) ; +#37875 = AXIS2_PLACEMENT_3D ( 'NONE', #98588, #43051, #20566 ) ; +#37876 = STYLED_ITEM ( 'NONE', ( #63338 ), #43294 ) ; +#37877 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2808578643762706384, 0.1499999999999999944 ) ) ; +#37878 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #47469, #88620 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #2833 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#37879 = STYLED_ITEM ( 'NONE', ( #4704 ), #59338 ) ; +#37881 = ORIENTED_EDGE ( 'NONE', *, *, #81, .F. ) ; +#37880 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#37882 = STYLED_ITEM ( 'NONE', ( #72963 ), #8801 ) ; +#37883 = ADVANCED_FACE ( 'NONE', ( #52319 ), #68597, .F. ) ; +#37884 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#37885 = ORIENTED_EDGE ( 'NONE', *, *, #64775, .F. ) ; +#37886 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#37887 = EDGE_LOOP ( 'NONE', ( #18388, #5975, #32076, #86446 ) ) ; +#37888 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81935 ) ) ; +#37889 = CARTESIAN_POINT ( 'NONE', ( -0.09294028489466890641, -0.9003478538782040408, 0.8299999999999988498 ) ) ; +#37890 = SURFACE_SIDE_STYLE ('',( #29227 ) ) ; +#37891 = EDGE_CURVE ( 'NONE', #36882, #986, #9767, .T. ) ; +#37893 = ORIENTED_EDGE ( 'NONE', *, *, #65753, .T. ) ; +#37892 = SURFACE_STYLE_FILL_AREA ( #70018 ) ; +#37894 = ADVANCED_FACE ( 'NONE', ( #24197 ), #1175, .F. ) ; +#37895 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#37896 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, -2.101292230494156476E-17, 0.6500000000000000222 ) ) ; +#37897 = AXIS2_PLACEMENT_3D ( 'NONE', #58849, #58345, #49152 ) ; +#37898 = FACE_OUTER_BOUND ( 'NONE', #72997, .T. ) ; +#37899 = FILL_AREA_STYLE ('',( #85345 ) ) ; +#37900 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37901 = ORIENTED_EDGE ( 'NONE', *, *, #41425, .T. ) ; +#37902 = VECTOR ( 'NONE', #10669, 1000.000000000000000 ) ; +#37903 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#37904 = CARTESIAN_POINT ( 'NONE', ( -1.876179938779914957, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#37906 = FACE_OUTER_BOUND ( 'NONE', #85193, .T. ) ; +#37905 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8100000000000000533 ) ) ; +#37907 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37908 = PLANE ( 'NONE', #38537 ) ; +#37909 = SURFACE_STYLE_FILL_AREA ( #51232 ) ; +#37910 = VECTOR ( 'NONE', #8315, 1000.000000000000000 ) ; +#37911 = DIRECTION ( 'NONE', ( 0.7071075504167430026, 0.7071060119555152568, 0.000000000000000000 ) ) ; +#37912 = ORIENTED_EDGE ( 'NONE', *, *, #41181, .T. ) ; +#37913 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37914 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#37915 = ORIENTED_EDGE ( 'NONE', *, *, #49304, .F. ) ; +#37916 = FILL_AREA_STYLE_COLOUR ( '', #66699 ) ; +#37918 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37917 = AXIS2_PLACEMENT_3D ( 'NONE', #81997, #85479, #52357 ) ; +#37919 = STYLED_ITEM ( 'NONE', ( #25890 ), #19413 ) ; +#37920 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37921 = EDGE_CURVE ( 'NONE', #13680, #83308, #47654, .T. ) ; +#37922 = VERTEX_POINT ( 'NONE', #54309 ) ; +#37923 = FILL_AREA_STYLE_COLOUR ( '', #60390 ) ; +#37924 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#37925 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207790140, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#37926 = FILL_AREA_STYLE ('',( #68543 ) ) ; +#37927 = FILL_AREA_STYLE_COLOUR ( '', #26995 ) ; +#37928 = LINE ( 'NONE', #44076, #34683 ) ; +#37929 = AXIS2_PLACEMENT_3D ( 'NONE', #40247, #10488, #95327 ) ; +#37930 = VECTOR ( 'NONE', #3263, 1000.000000000000000 ) ; +#37931 = STYLED_ITEM ( 'NONE', ( #15514 ), #34745 ) ; +#37932 = LINE ( 'NONE', #36930, #76227 ) ; +#37933 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#37934 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#37935 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37936 = FILL_AREA_STYLE_COLOUR ( '', #97407 ) ; +#37937 = FACE_OUTER_BOUND ( 'NONE', #91973, .T. ) ; +#37938 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#37939 = STYLED_ITEM ( 'NONE', ( #97569 ), #36521 ) ; +#37940 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21750, 'distance_accuracy_value', 'NONE'); +#37941 = STYLED_ITEM ( 'NONE', ( #8723 ), #96573 ) ; +#37942 = LINE ( 'NONE', #69033, #42228 ) ; +#37943 = VERTEX_POINT ( 'NONE', #32342 ) ; +#37944 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37946 = ORIENTED_EDGE ( 'NONE', *, *, #833, .F. ) ; +#37945 = AXIS2_PLACEMENT_3D ( 'NONE', #33755, #10147, #10662 ) ; +#37947 = FILL_AREA_STYLE_COLOUR ( '', #64909 ) ; +#37948 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63343, 'distance_accuracy_value', 'NONE'); +#37949 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29684, 'distance_accuracy_value', 'NONE'); +#37950 = STYLED_ITEM ( 'NONE', ( #3403 ), #9053 ) ; +#37951 = CARTESIAN_POINT ( 'NONE', ( 1.060148841163599975, -1.043393888298179917, 0.8100000000000000533 ) ) ; +#37952 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706538E-17, 0.8199999999999999512, -0.2000000000000000111 ) ) ; +#37953 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#37954 = PRESENTATION_STYLE_ASSIGNMENT (( #38957 ) ) ; +#37955 = STYLED_ITEM ( 'NONE', ( #53084 ), #11290 ) ; +#37956 = LINE ( 'NONE', #5758, #88481 ) ; +#37957 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#37958 = DIRECTION ( 'NONE', ( -0.7071045084557385785, -0.7071090539100516326, 0.000000000000000000 ) ) ; +#37959 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37960 = ORIENTED_EDGE ( 'NONE', *, *, #41981, .F. ) ; +#37961 = LINE ( 'NONE', #22635, #88400 ) ; +#37962 = EDGE_CURVE ( 'NONE', #33859, #35664, #40517, .T. ) ; +#37963 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89633, 'distance_accuracy_value', 'NONE'); +#37964 = AXIS2_PLACEMENT_3D ( 'NONE', #94310, #100849, #39709 ) ; +#37965 = ORIENTED_EDGE ( 'NONE', *, *, #98928, .T. ) ; +#37966 = FACE_OUTER_BOUND ( 'NONE', #53605, .T. ) ; +#37967 = ADVANCED_FACE ( 'NONE', ( #38988 ), #62489, .T. ) ; +#37968 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#37969 = SURFACE_SIDE_STYLE ('',( #6727 ) ) ; +#37970 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#37971 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#37972 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#37974 = ORIENTED_EDGE ( 'NONE', *, *, #50945, .T. ) ; +#37973 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80410 ), #33093 ) ; +#37975 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#37976 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24901, 'distance_accuracy_value', 'NONE'); +#37977 = SURFACE_STYLE_FILL_AREA ( #13926 ) ; +#37978 = VECTOR ( 'NONE', #53544, 1000.000000000000000 ) ; +#37979 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#37980 = ADVANCED_FACE ( 'NONE', ( #79305 ), #3700, .F. ) ; +#37981 = ORIENTED_EDGE ( 'NONE', *, *, #77534, .F. ) ; +#37982 = DIRECTION ( 'NONE', ( -0.7071064476869688420, -0.7071071146859688739, 0.000000000000000000 ) ) ; +#37983 = LINE ( 'NONE', #84436, #78281 ) ; +#37984 = VECTOR ( 'NONE', #77213, 1000.000000000000114 ) ; +#37985 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81811 ) ) ; +#37986 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#37987 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#37988 = CARTESIAN_POINT ( 'NONE', ( 1.578229014142009889, -1.479722134560319979, 0.8300000000000001821 ) ) ; +#37989 = ORIENTED_EDGE ( 'NONE', *, *, #30211, .T. ) ; +#37990 = STYLED_ITEM ( 'NONE', ( #54815 ), #47201 ) ; +#37991 = ORIENTED_EDGE ( 'NONE', *, *, #88594, .T. ) ; +#37992 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88568 ) ) ; +#37993 = VERTEX_POINT ( 'NONE', #87967 ) ; +#37995 = VERTEX_POINT ( 'NONE', #11275 ) ; +#37994 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#37996 = EDGE_CURVE ( 'NONE', #71133, #98563, #65475, .T. ) ; +#37997 = PRESENTATION_STYLE_ASSIGNMENT (( #46107 ) ) ; +#37999 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#37998 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#38000 = PRESENTATION_STYLE_ASSIGNMENT (( #5297 ) ) ; +#38001 = ORIENTED_EDGE ( 'NONE', *, *, #57533, .T. ) ; +#38002 = PRESENTATION_STYLE_ASSIGNMENT (( #54328 ) ) ; +#38004 = FILL_AREA_STYLE_COLOUR ( '', #35346 ) ; +#38003 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38005 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38006 = ORIENTED_EDGE ( 'NONE', *, *, #81231, .F. ) ; +#38007 = CARTESIAN_POINT ( 'NONE', ( 1.420458916718859932, -1.419416888468929994, 0.8299999999999999600 ) ) ; +#38008 = LINE ( 'NONE', #53823, #93660 ) ; +#38009 = VECTOR ( 'NONE', #56981, 1000.000000000000000 ) ; +#38010 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78732 ) ) ; +#38011 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38012 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88583 ) ) ; +#38013 = ORIENTED_EDGE ( 'NONE', *, *, #59726, .F. ) ; +#38015 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.000000000000000000 ) ) ; +#38014 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#38016 = ORIENTED_EDGE ( 'NONE', *, *, #82713, .T. ) ; +#38017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90187 ), #65719 ) ; +#38018 = STYLED_ITEM ( 'NONE', ( #55195 ), #36790 ) ; +#38019 = ADVANCED_FACE ( 'NONE', ( #49177 ), #36819, .F. ) ; +#38020 = VECTOR ( 'NONE', #87934, 1000.000000000000114 ) ; +#38022 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38021 = FACE_OUTER_BOUND ( 'NONE', #85368, .T. ) ; +#38023 = VECTOR ( 'NONE', #16746, 1000.000000000000000 ) ; +#38024 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8648700000000000276 ) ) ; +#38025 = ORIENTED_EDGE ( 'NONE', *, *, #42945, .T. ) ; +#38026 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.157142857142859915, 0.8299999999999999600 ) ) ; +#38027 = ORIENTED_EDGE ( 'NONE', *, *, #52421, .F. ) ; +#38028 = SURFACE_STYLE_FILL_AREA ( #53344 ) ; +#38029 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85421, 'distance_accuracy_value', 'NONE'); +#38030 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39631 ) ) ; +#38031 = SURFACE_STYLE_FILL_AREA ( #85991 ) ; +#38032 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333326642, 0.8999999999999990230, 1.747825839084889375E-76 ) ) ; +#38033 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#38034 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#38035 = FACE_OUTER_BOUND ( 'NONE', #56747, .T. ) ; +#38036 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38037 = SURFACE_SIDE_STYLE ('',( #7305 ) ) ; +#38038 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#38039 = ORIENTED_EDGE ( 'NONE', *, *, #4778, .T. ) ; +#38040 = ADVANCED_FACE ( 'NONE', ( #59881 ), #21037, .T. ) ; +#38041 = FILL_AREA_STYLE_COLOUR ( '', #44824 ) ; +#38042 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38044 = SURFACE_SIDE_STYLE ('',( #45650 ) ) ; +#38043 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, 0.000000000000000000 ) ) ; +#38045 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.35000000000000142 ) ) ; +#38046 = SURFACE_SIDE_STYLE ('',( #54381 ) ) ; +#38047 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38048 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#38049 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999940048, -2.500000000000000000, -0.02000000000005449849 ) ) ; +#38050 = ADVANCED_FACE ( 'NONE', ( #66988 ), #13285, .T. ) ; +#38051 = ORIENTED_EDGE ( 'NONE', *, *, #24044, .F. ) ; +#38052 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#38053 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38054 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999994671, -0.02000000000000839995 ) ) ; +#38055 = SURFACE_STYLE_FILL_AREA ( #21710 ) ; +#38056 = CARTESIAN_POINT ( 'NONE', ( -0.02315300183346909874, -1.415447185383410078, 0.8100000000000000533 ) ) ; +#38057 = CARTESIAN_POINT ( 'NONE', ( 4.515212750249974150, 8.696595249750023626, 0.8648700000000000276 ) ) ; +#38058 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53848, 'distance_accuracy_value', 'NONE'); +#38059 = SURFACE_SIDE_STYLE ('',( #6812 ) ) ; +#38060 = FACE_OUTER_BOUND ( 'NONE', #81064, .T. ) ; +#38061 = SURFACE_STYLE_FILL_AREA ( #22229 ) ; +#38062 = SURFACE_STYLE_USAGE ( .BOTH. , #15018 ) ; +#38063 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38064 = AXIS2_PLACEMENT_3D ( 'NONE', #56592, #87695, #48909 ) ; +#38065 = FILL_AREA_STYLE_COLOUR ( '', #665 ) ; +#38066 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38067 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.000000000000000000 ) ) ; +#38068 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#38069 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72749 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69518, #44528, #61908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38070 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#38071 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #544, 'distance_accuracy_value', 'NONE'); +#38072 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15965, 'distance_accuracy_value', 'NONE'); +#38073 = SURFACE_STYLE_USAGE ( .BOTH. , #76872 ) ; +#38074 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13568 ) ) ; +#38075 = VECTOR ( 'NONE', #19739, 1000.000000000000000 ) ; +#38076 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#38077 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38078 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50606, #20424, #28592, #19933 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38079 = AXIS2_PLACEMENT_3D ( 'NONE', #47341, #9474, #63202 ) ; +#38080 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#38081 = EDGE_LOOP ( 'NONE', ( #69184, #20281, #68936, #80392 ) ) ; +#38082 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38084 = EDGE_CURVE ( 'NONE', #92605, #25440, #69989, .T. ) ; +#38083 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#38085 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26043, 'distance_accuracy_value', 'NONE'); +#38086 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70722 ) ) ; +#38087 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41813 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32616, #55108, #95351 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38088 = SURFACE_STYLE_FILL_AREA ( #70207 ) ; +#38089 = EDGE_LOOP ( 'NONE', ( #83154, #97943, #31222, #71173 ) ) ; +#38090 = VECTOR ( 'NONE', #92737, 1000.000000000000000 ) ; +#38091 = ADVANCED_FACE ( 'NONE', ( #94972 ), #47527, .T. ) ; +#38092 = ADVANCED_FACE ( 'NONE', ( #15854 ), #25096, .T. ) ; +#38093 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8611 ), #16915 ) ; +#38094 = VECTOR ( 'NONE', #56710, 1000.000000000000000 ) ; +#38095 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#38096 = FILL_AREA_STYLE ('',( #6843 ) ) ; +#38097 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#38098 = SURFACE_SIDE_STYLE ('',( #100247 ) ) ; +#38099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82139 ) ) ; +#38100 = ORIENTED_EDGE ( 'NONE', *, *, #16581, .F. ) ; +#38101 = FILL_AREA_STYLE_COLOUR ( '', #25332 ) ; +#38102 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70738 ) ) ; +#38103 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59172, 'distance_accuracy_value', 'NONE'); +#38104 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85381 ), #13598 ) ; +#38105 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#38106 = FILL_AREA_STYLE_COLOUR ( '', #77917 ) ; +#38107 = ADVANCED_FACE ( 'NONE', ( #85828 ), #549, .T. ) ; +#38108 = ORIENTED_EDGE ( 'NONE', *, *, #99287, .T. ) ; +#38109 = ORIENTED_EDGE ( 'NONE', *, *, #92804, .T. ) ; +#38110 = EDGE_CURVE ( 'NONE', #41000, #88355, #19404, .T. ) ; +#38111 = LINE ( 'NONE', #1308, #17894 ) ; +#38112 = AXIS2_PLACEMENT_3D ( 'NONE', #50190, #87444, #32325 ) ; +#38113 = ORIENTED_EDGE ( 'NONE', *, *, #97615, .T. ) ; +#38114 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38115 = SURFACE_STYLE_USAGE ( .BOTH. , #68708 ) ; +#38116 = FILL_AREA_STYLE_COLOUR ( '', #56497 ) ; +#38117 = SURFACE_STYLE_FILL_AREA ( #76907 ) ; +#38118 = SURFACE_STYLE_USAGE ( .BOTH. , #29923 ) ; +#38119 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7771, #16499, #70650, #55379 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38120 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #79511, #82894 ) ; +#38121 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38122 = VERTEX_POINT ( 'NONE', #80716 ) ; +#38123 = VERTEX_POINT ( 'NONE', #65358 ) ; +#38124 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38125 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38126 = EDGE_CURVE ( 'NONE', #56071, #28217, #56741, .T. ) ; +#38127 = LINE ( 'NONE', #16601, #36019 ) ; +#38129 = PRESENTATION_STYLE_ASSIGNMENT (( #16603 ) ) ; +#38128 = CARTESIAN_POINT ( 'NONE', ( 5.264745166500082618, 6.971255166500239575, 0.8991599999999999593 ) ) ; +#38131 = PRESENTATION_STYLE_ASSIGNMENT (( #6878 ) ) ; +#38130 = VECTOR ( 'NONE', #81832, 1000.000000000000000 ) ; +#38132 = ADVANCED_FACE ( 'NONE', ( #87849 ), #41900, .F. ) ; +#38133 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38134 = VERTEX_POINT ( 'NONE', #18384 ) ; +#38136 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38135 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8648700000000000276 ) ) ; +#38137 = ORIENTED_EDGE ( 'NONE', *, *, #63429, .T. ) ; +#38138 = AXIS2_PLACEMENT_3D ( 'NONE', #535, #31689, #8614 ) ; +#38139 = ORIENTED_EDGE ( 'NONE', *, *, #1173, .F. ) ; +#38140 = EDGE_CURVE ( 'NONE', #89974, #37519, #17380, .T. ) ; +#38142 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38141 = PRESENTATION_STYLE_ASSIGNMENT (( #23830 ) ) ; +#38143 = FACE_OUTER_BOUND ( 'NONE', #10011, .T. ) ; +#38144 = EDGE_CURVE ( 'NONE', #85557, #48436, #48567, .T. ) ; +#38145 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89083 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7669, #62409, #24118 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38146 = PLANE ( 'NONE', #58761 ) ; +#38148 = ORIENTED_EDGE ( 'NONE', *, *, #65746, .F. ) ; +#38147 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38149 = SURFACE_SIDE_STYLE ('',( #61646 ) ) ; +#38150 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38151 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6700000000000000400, 0.000000000000000000 ) ) ; +#38152 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38153 = EDGE_LOOP ( 'NONE', ( #23027, #98232, #57853, #58248 ) ) ; +#38154 = FILL_AREA_STYLE ('',( #16130 ) ) ; +#38155 = ORIENTED_EDGE ( 'NONE', *, *, #80958, .T. ) ; +#38156 = ORIENTED_EDGE ( 'NONE', *, *, #48711, .F. ) ; +#38157 = FILL_AREA_STYLE ('',( #6907 ) ) ; +#38158 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38159 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38160 = CARTESIAN_POINT ( 'NONE', ( 0.03333333333332499926, -3.500000000000000000, 0.000000000000000000 ) ) ; +#38161 = VECTOR ( 'NONE', #37544, 1000.000000000000000 ) ; +#38162 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#38163 = FILL_AREA_STYLE ('',( #5454 ) ) ; +#38164 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38165 = ORIENTED_EDGE ( 'NONE', *, *, #96738, .T. ) ; +#38166 = ADVANCED_FACE ( 'NONE', ( #79710 ), #73034, .F. ) ; +#38167 = ORIENTED_EDGE ( 'NONE', *, *, #100544, .F. ) ; +#38168 = LINE ( 'NONE', #92744, #21202 ) ; +#38169 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38170 = AXIS2_PLACEMENT_3D ( 'NONE', #35263, #34753, #37257 ) ; +#38171 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#38172 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38173 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38174 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#38175 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146560196, 0.3100465759269649957, 0.8100000000000000533 ) ) ; +#38176 = FILL_AREA_STYLE_COLOUR ( '', #69510 ) ; +#38177 = PLANE ( 'NONE', #57568 ) ; +#38178 = EDGE_CURVE ( 'NONE', #39192, #79322, #83591, .T. ) ; +#38179 = VERTEX_POINT ( 'NONE', #23307 ) ; +#38180 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#38181 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38182 = SURFACE_SIDE_STYLE ('',( #92755 ) ) ; +#38183 = VECTOR ( 'NONE', #52676, 1000.000000000000000 ) ; +#38184 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#38185 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#38186 = EDGE_CURVE ( 'NONE', #1370, #72705, #53945, .T. ) ; +#38187 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59431 ) ) ; +#38188 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.000000000000000000 ) ) ; +#38189 = FILL_AREA_STYLE_COLOUR ( '', #61990 ) ; +#38190 = ADVANCED_FACE ( 'NONE', ( #76404 ), #53446, .F. ) ; +#38191 = VECTOR ( 'NONE', #74963, 1000.000000000000000 ) ; +#38192 = PLANE ( 'NONE', #50268 ) ; +#38193 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#38194 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49658 ), #25184 ) ; +#38195 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90321, 'distance_accuracy_value', 'NONE'); +#38196 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38197 = CARTESIAN_POINT ( 'NONE', ( -1.297348492277750287, -1.386462394657215436, 0.8099999999997035127 ) ) ; +#38198 = EDGE_LOOP ( 'NONE', ( #37613, #56780, #11771, #21471 ) ) ; +#38199 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.000000000000000000, 0.4500000000000000111 ) ) ; +#38200 = PLANE ( 'NONE', #12682 ) ; +#38201 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#38202 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45121, 'distance_accuracy_value', 'NONE'); +#38203 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38204 = CARTESIAN_POINT ( 'NONE', ( 1.149977098104328244, -1.140782136996280505, 0.8099999999999010214 ) ) ; +#38205 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65165 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99245, #52890, #67657 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38206 = ADVANCED_FACE ( 'NONE', ( #7887 ), #62136, .F. ) ; +#38207 = ADVANCED_FACE ( 'NONE', ( #89852 ), #21282, .T. ) ; +#38208 = PLANE ( 'NONE', #30384 ) ; +#38209 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43084 ), #41437 ) ; +#38210 = ORIENTED_EDGE ( 'NONE', *, *, #13338, .T. ) ; +#38212 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38211 = FILL_AREA_STYLE ('',( #14674 ) ) ; +#38213 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63644, 'distance_accuracy_value', 'NONE'); +#38214 = FACE_OUTER_BOUND ( 'NONE', #46835, .T. ) ; +#38215 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30036, 'distance_accuracy_value', 'NONE'); +#38216 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38217 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38218 = EDGE_CURVE ( 'NONE', #25108, #62932, #18116, .T. ) ; +#38219 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.600000000000000089, -13.35000000000000142 ) ) ; +#38220 = ORIENTED_EDGE ( 'NONE', *, *, #33246, .F. ) ; +#38221 = ORIENTED_EDGE ( 'NONE', *, *, #42890, .F. ) ; +#38222 = ADVANCED_FACE ( 'NONE', ( #79961 ), #88117, .T. ) ; +#38223 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95416 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1899, #24904, #16166 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38224 = PRESENTATION_STYLE_ASSIGNMENT (( #62730 ) ) ; +#38225 = ORIENTED_EDGE ( 'NONE', *, *, #66025, .F. ) ; +#38226 = CARTESIAN_POINT ( 'NONE', ( -0.3050011667720459729, -1.377680218341680085, 0.8299999999999999600 ) ) ; +#38228 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#38227 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8758 ), #88811 ) ; +#38229 = FILL_AREA_STYLE ('',( #16711 ) ) ; +#38230 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#38231 = VECTOR ( 'NONE', #24586, 1000.000000000000000 ) ; +#38232 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#38233 = PRODUCT_CONTEXT ( 'NONE', #7658, 'mechanical' ) ; +#38234 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853420540, 1.551146575926970472, 0.8100000000000000533 ) ) ; +#38236 = ORIENTED_EDGE ( 'NONE', *, *, #72547, .F. ) ; +#38235 = ORIENTED_EDGE ( 'NONE', *, *, #28623, .T. ) ; +#38237 = STYLED_ITEM ( 'NONE', ( #97357 ), #3261 ) ; +#38238 = ORIENTED_EDGE ( 'NONE', *, *, #3251, .F. ) ; +#38239 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#38240 = EDGE_CURVE ( 'NONE', #26946, #98628, #9410, .T. ) ; +#38241 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84453, #62509, #29817, #91606 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38242 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#38243 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#38244 = AXIS2_PLACEMENT_3D ( 'NONE', #87340, #1588, #65357 ) ; +#38245 = ORIENTED_EDGE ( 'NONE', *, *, #34927, .F. ) ; +#38246 = EDGE_LOOP ( 'NONE', ( #49561, #94421, #51713, #47036 ) ) ; +#38247 = EDGE_CURVE ( 'NONE', #50963, #56923, #42082, .T. ) ; +#38248 = PLANE ( 'NONE', #80613 ) ; +#38249 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.004999999999999959338, -0.1499999999999999944 ) ) ; +#38251 = DIRECTION ( 'NONE', ( 0.7071060119555133694, -0.7071075504167448900, 0.000000000000000000 ) ) ; +#38250 = LINE ( 'NONE', #61750, #75872 ) ; +#38252 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4808578643762691507, -0.2434314575050761376 ) ) ; +#38253 = ORIENTED_EDGE ( 'NONE', *, *, #90775, .T. ) ; +#38254 = AXIS2_PLACEMENT_3D ( 'NONE', #7767, #14469, #99669 ) ; +#38255 = CARTESIAN_POINT ( 'NONE', ( -0.4484892475557449854, -1.042938524989579951, 0.8100000000000000533 ) ) ; +#38256 = ORIENTED_EDGE ( 'NONE', *, *, #22196, .T. ) ; +#38257 = VERTEX_POINT ( 'NONE', #63132 ) ; +#38258 = SURFACE_STYLE_USAGE ( .BOTH. , #14719 ) ; +#38259 = ADVANCED_FACE ( 'NONE', ( #94221 ), #54967, .T. ) ; +#38260 = EDGE_CURVE ( 'NONE', #69086, #19475, #96733, .T. ) ; +#38261 = VECTOR ( 'NONE', #68147, 1000.000000000000000 ) ; +#38262 = FILL_AREA_STYLE ('',( #59897 ) ) ; +#38264 = VERTEX_POINT ( 'NONE', #26341 ) ; +#38263 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#38265 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100138 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1537, #94919, #85263 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38266 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38267 = VECTOR ( 'NONE', #3125, 1000.000000000000114 ) ; +#38268 = ORIENTED_EDGE ( 'NONE', *, *, #16353, .T. ) ; +#38270 = PRESENTATION_STYLE_ASSIGNMENT (( #29104 ) ) ; +#38269 = LINE ( 'NONE', #85714, #19003 ) ; +#38271 = SURFACE_SIDE_STYLE ('',( #7026 ) ) ; +#38272 = ORIENTED_EDGE ( 'NONE', *, *, #55304, .T. ) ; +#38274 = ORIENTED_EDGE ( 'NONE', *, *, #71677, .T. ) ; +#38273 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94863, #95881, #79093, #9551, #1486, #88262, #18271, #49454, #80614, #17276, #48468, #64266, #10041, #10534, #24492, #79601, #33124, #41799, #32632 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.366134600599809946E-05, 2.678053936399091698E-05, 3.925672662558368878E-05, 5.134489543513020670E-05, 6.322496733117238777E-05, 7.487673038755926394E-05, 8.649796808712891590E-05, 9.812875356678294142E-05, 0.0001098766569990738680, 0.0001215772214741425787, 0.0001333030571762213118, 0.0001451137840694615290, 0.0001571522639181528779, 0.0001694924733769890386, 0.0001820943669839384315, 0.0001951167467603316381 ), + .UNSPECIFIED. ) ; +#38276 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38275 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38277 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26853 ) ) ; +#38278 = PLANE ( 'NONE', #95430 ) ; +#38279 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#38280 = CARTESIAN_POINT ( 'NONE', ( 1.328303542420389949, -1.268071887441960088, 0.8299999999999997380 ) ) ; +#38281 = CARTESIAN_POINT ( 'NONE', ( 0.001420454545454360095, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#38282 = VERTEX_POINT ( 'NONE', #66619 ) ; +#38283 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38284 = EDGE_CURVE ( 'NONE', #100360, #54104, #50352, .T. ) ; +#38285 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90066 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73411, #35126, #59117 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38286 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#38287 = VERTEX_POINT ( 'NONE', #3836 ) ; +#38288 = PLANE ( 'NONE', #72576 ) ; +#38290 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66130, 'distance_accuracy_value', 'NONE'); +#38289 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38291 = LINE ( 'NONE', #84735, #28453 ) ; +#38292 = VECTOR ( 'NONE', #16648, 1000.000000000000000 ) ; +#38293 = VECTOR ( 'NONE', #61572, 1000.000000000000000 ) ; +#38294 = SURFACE_STYLE_FILL_AREA ( #14753 ) ; +#38296 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38298 = AXIS2_PLACEMENT_3D ( 'NONE', #64825, #80674, #87295 ) ; +#38297 = FACE_OUTER_BOUND ( 'NONE', #63570, .T. ) ; +#38299 = FACE_OUTER_BOUND ( 'NONE', #40355, .T. ) ; +#38301 = EDGE_CURVE ( 'NONE', #7722, #98110, #42653, .T. ) ; +#38300 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.01000000000000000021, 0.4500000000000000111 ) ) ; +#38302 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38303 = CYLINDRICAL_SURFACE ( 'NONE', #77341, 1.319494367338009955 ) ; +#38305 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54572 ) ) ; +#38304 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30762 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9285, #70124, #56383 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38306 = LINE ( 'NONE', #23483, #34623 ) ; +#38307 = AXIS2_PLACEMENT_3D ( 'NONE', #43687, #20719, #12982 ) ; +#38308 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38309 = LINE ( 'NONE', #69396, #82239 ) ; +#38310 = PRESENTATION_STYLE_ASSIGNMENT (( #84750 ) ) ; +#38311 = EDGE_CURVE ( 'NONE', #75533, #77743, #35515, .T. ) ; +#38312 = PRESENTATION_STYLE_ASSIGNMENT (( #36796 ) ) ; +#38313 = SURFACE_SIDE_STYLE ('',( #30602 ) ) ; +#38314 = DIRECTION ( 'NONE', ( -0.7071067811865476838, -7.850462293418874601E-17, -0.7071067811865474617 ) ) ; +#38315 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38316 = EDGE_CURVE ( 'NONE', #27604, #87301, #9078, .T. ) ; +#38317 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9953 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #687, #186, #31329 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38318 = SURFACE_SIDE_STYLE ('',( #53630 ) ) ; +#38319 = VECTOR ( 'NONE', #73570, 1000.000000000000000 ) ; +#38320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11825, 'distance_accuracy_value', 'NONE'); +#38321 = VERTEX_POINT ( 'NONE', #34514 ) ; +#38322 = DIRECTION ( 'NONE', ( 0.3438200982495990266, -0.000000000000000000, -0.9390355371548171348 ) ) ; +#38323 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#38324 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38325 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38326 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25648 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34375, #2711, #73162 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38327 = PRESENTATION_STYLE_ASSIGNMENT (( #39307 ) ) ; +#38328 = LINE ( 'NONE', #93405, #89702 ) ; +#38329 = ADVANCED_FACE ( 'NONE', ( #96238 ), #98196, .T. ) ; +#38330 = STYLED_ITEM ( 'NONE', ( #100825 ), #29353 ) ; +#38331 = EDGE_LOOP ( 'NONE', ( #5440, #76669, #92434, #3148 ) ) ; +#38332 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42903, #90359, #43396 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38333 = ORIENTED_EDGE ( 'NONE', *, *, #21377, .F. ) ; +#38334 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, -9.880000000000000782, 0.2500000000000000000 ) ) ; +#38335 = PLANE ( 'NONE', #15579 ) ; +#38336 = CARTESIAN_POINT ( 'NONE', ( -0.1634999987230950080, -0.9726617844338850682, 0.8100000000000000533 ) ) ; +#38337 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#38338 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#38339 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38340 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38341 = FILL_AREA_STYLE_COLOUR ( '', #89379 ) ; +#38342 = CARTESIAN_POINT ( 'NONE', ( -0.2929073563266554325, -1.031261123858768780, 0.8100000000001996714 ) ) ; +#38343 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38344 = ORIENTED_EDGE ( 'NONE', *, *, #62023, .F. ) ; +#38345 = FILL_AREA_STYLE_COLOUR ( '', #25416 ) ; +#38346 = STYLED_ITEM ( 'NONE', ( #98796 ), #49265 ) ; +#38347 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.500000000000000000, 0.8299999999999999600 ) ) ; +#38348 = ORIENTED_EDGE ( 'NONE', *, *, #36719, .F. ) ; +#38349 = SURFACE_STYLE_USAGE ( .BOTH. , #85798 ) ; +#38350 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92814, #99907, #79072 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38351 = EDGE_CURVE ( 'NONE', #89004, #78572, #36015, .T. ) ; +#38352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7277 ) ) ; +#38353 = PRESENTATION_STYLE_ASSIGNMENT (( #63368 ) ) ; +#38354 = VERTEX_POINT ( 'NONE', #35015 ) ; +#38355 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5713 ), #61259 ) ; +#38356 = EDGE_CURVE ( 'NONE', #6062, #37149, #28336, .T. ) ; +#38357 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#38358 = PRESENTATION_STYLE_ASSIGNMENT (( #67460 ) ) ; +#38359 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38360 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#38361 = SURFACE_SIDE_STYLE ('',( #22514 ) ) ; +#38363 = VERTEX_POINT ( 'NONE', #34006 ) ; +#38362 = ORIENTED_EDGE ( 'NONE', *, *, #35916, .T. ) ; +#38364 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38365 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#38366 = EDGE_LOOP ( 'NONE', ( #89986, #76159, #77554, #49058 ) ) ; +#38367 = PLANE ( 'NONE', #72115 ) ; +#38368 = VECTOR ( 'NONE', #83901, 1000.000000000000000 ) ; +#38369 = STYLED_ITEM ( 'NONE', ( #13910 ), #22611 ) ; +#38370 = CARTESIAN_POINT ( 'NONE', ( -0.4458447660039659977, -1.054313421655699967, 0.8100000000000000533 ) ) ; +#38371 = ORIENTED_EDGE ( 'NONE', *, *, #98702, .T. ) ; +#38372 = ORIENTED_EDGE ( 'NONE', *, *, #43953, .F. ) ; +#38375 = VECTOR ( 'NONE', #67762, 1000.000000000000000 ) ; +#38374 = AXIS2_PLACEMENT_3D ( 'NONE', #93571, #8769, #70641 ) ; +#38373 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38376 = VECTOR ( 'NONE', #90552, 1000.000000000000000 ) ; +#38377 = SURFACE_STYLE_USAGE ( .BOTH. , #7123 ) ; +#38378 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38379 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8648700000000000276 ) ) ; +#38380 = FILL_AREA_STYLE_COLOUR ( '', #44637 ) ; +#38381 = EDGE_LOOP ( 'NONE', ( #71730, #27439, #72290, #31624 ) ) ; +#38382 = ORIENTED_EDGE ( 'NONE', *, *, #96845, .F. ) ; +#38383 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38384 = ORIENTED_EDGE ( 'NONE', *, *, #25733, .T. ) ; +#38385 = SURFACE_SIDE_STYLE ('',( #59886 ) ) ; +#38386 = EDGE_CURVE ( 'NONE', #329, #36002, #65121, .T. ) ; +#38387 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28608 ), #17223 ) ; +#38389 = ORIENTED_EDGE ( 'NONE', *, *, #28832, .F. ) ; +#38388 = LINE ( 'NONE', #100526, #68887 ) ; +#38390 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#38391 = FACE_OUTER_BOUND ( 'NONE', #10643, .T. ) ; +#38392 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38393 = EDGE_LOOP ( 'NONE', ( #30168, #65752, #5541, #90002, #77215, #8622 ) ) ; +#38394 = EDGE_CURVE ( 'NONE', #2903, #48138, #20275, .T. ) ; +#38395 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, 0.000000000000000000 ) ) ; +#38396 = ORIENTED_EDGE ( 'NONE', *, *, #37033, .T. ) ; +#38397 = CARTESIAN_POINT ( 'NONE', ( 0.02974286737007770035, -0.9500768360162820114, 0.8299999999999988498 ) ) ; +#38398 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#38399 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67737 ), #13916 ) ; +#38401 = VERTEX_POINT ( 'NONE', #85453 ) ; +#38400 = PRESENTATION_STYLE_ASSIGNMENT (( #15881 ) ) ; +#38402 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38403 = CARTESIAN_POINT ( 'NONE', ( 1.525795062450169937, -1.430103682213279992, 0.8100000000000000533 ) ) ; +#38404 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8075 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37290, #84234, #7032 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38405 = PRESENTATION_STYLE_ASSIGNMENT (( #23586 ) ) ; +#38406 = EDGE_CURVE ( 'NONE', #82970, #11668, #13422, .T. ) ; +#38407 = FILL_AREA_STYLE ('',( #61902 ) ) ; +#38408 = ORIENTED_EDGE ( 'NONE', *, *, #86374, .T. ) ; +#38409 = FACE_OUTER_BOUND ( 'NONE', #21172, .T. ) ; +#38410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10608 ), #2551 ) ; +#38411 = VECTOR ( 'NONE', #97996, 1000.000000000000000 ) ; +#38412 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38413 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#38414 = SURFACE_STYLE_FILL_AREA ( #46016 ) ; +#38415 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38416 = SURFACE_STYLE_FILL_AREA ( #22584 ) ; +#38417 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#38418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28644 ), #30287 ) ; +#38419 = VERTEX_POINT ( 'NONE', #76787 ) ; +#38420 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38421 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.266666666666667052, 0.000000000000000000 ) ) ; +#38422 = FILL_AREA_STYLE ('',( #46556 ) ) ; +#38423 = VERTEX_POINT ( 'NONE', #100156 ) ; +#38424 = AXIS2_PLACEMENT_3D ( 'NONE', #61863, #92938, #8629 ) ; +#38425 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#38426 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38427 = EDGE_CURVE ( 'NONE', #32963, #98314, #22166, .T. ) ; +#38428 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38429 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82471 ) ) ; +#38430 = ADVANCED_FACE ( 'NONE', ( #44621 ), #14959, .T. ) ; +#38431 = ORIENTED_EDGE ( 'NONE', *, *, #4631, .F. ) ; +#38432 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#38433 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38434 = LINE ( 'NONE', #100575, #15963 ) ; +#38435 = FACE_OUTER_BOUND ( 'NONE', #75935, .T. ) ; +#38436 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93021 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50600, #88873, #66392 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38437 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38438 = VECTOR ( 'NONE', #59456, 1000.000000000000000 ) ; +#38439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38440 = SURFACE_SIDE_STYLE ('',( #63462 ) ) ; +#38441 = FACE_OUTER_BOUND ( 'NONE', #65811, .T. ) ; +#38442 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#38443 = PRESENTATION_STYLE_ASSIGNMENT (( #39431 ) ) ; +#38444 = FILL_AREA_STYLE_COLOUR ( '', #97484 ) ; +#38445 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38446 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21927 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63423, #6666, #77694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38447 = EDGE_CURVE ( 'NONE', #9552, #97744, #29330, .T. ) ; +#38448 = SURFACE_STYLE_USAGE ( .BOTH. , #84882 ) ; +#38449 = EDGE_CURVE ( 'NONE', #74962, #66265, #7268, .T. ) ; +#38450 = LINE ( 'NONE', #75729, #37341 ) ; +#38451 = ORIENTED_EDGE ( 'NONE', *, *, #66423, .F. ) ; +#38452 = EDGE_LOOP ( 'NONE', ( #63894, #4044, #8766, #5469 ) ) ; +#38453 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38454 = EDGE_CURVE ( 'NONE', #98440, #48947, #82236, .T. ) ; +#38455 = EDGE_CURVE ( 'NONE', #777, #13261, #30823, .T. ) ; +#38456 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 2.143355994988570127E-63 ) ) ; +#38457 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85548 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94052, #15456, #77774 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38458 = CARTESIAN_POINT ( 'NONE', ( -0.1055551954118710001, -1.507644428662930025, 0.8300000000000004041 ) ) ; +#38459 = SURFACE_SIDE_STYLE ('',( #8721 ) ) ; +#38460 = SURFACE_SIDE_STYLE ('',( #7222 ) ) ; +#38461 = FACE_OUTER_BOUND ( 'NONE', #43910, .T. ) ; +#38462 = VERTEX_POINT ( 'NONE', #60995 ) ; +#38463 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 3.123820061220065281, 0.000000000000000000 ) ) ; +#38464 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38465 = FILL_AREA_STYLE ('',( #61965 ) ) ; +#38466 = VERTEX_POINT ( 'NONE', #46642 ) ; +#38467 = CARTESIAN_POINT ( 'NONE', ( 1.154841114944652247, -1.214867104881771409, 0.8099999999998548361 ) ) ; +#38468 = EDGE_CURVE ( 'NONE', #30759, #85813, #99661, .T. ) ; +#38469 = ORIENTED_EDGE ( 'NONE', *, *, #74471, .F. ) ; +#38470 = ADVANCED_FACE ( 'NONE', ( #28819 ), #6281, .F. ) ; +#38471 = FACE_OUTER_BOUND ( 'NONE', #26198, .T. ) ; +#38472 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38473 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38474 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#38475 = ORIENTED_EDGE ( 'NONE', *, *, #90086, .T. ) ; +#38476 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12299 ), #7405 ) ; +#38477 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49953 ), #71063 ) ; +#38478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43881 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7673, #1112, #31751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38479 = VERTEX_POINT ( 'NONE', #79325 ) ; +#38480 = VECTOR ( 'NONE', #27345, 1000.000000000000000 ) ; +#38481 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38482 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#38483 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38484 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38485 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#38486 = AXIS2_PLACEMENT_3D ( 'NONE', #53958, #91731, #70270 ) ; +#38487 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38488 = VECTOR ( 'NONE', #32712, 1000.000000000000000 ) ; +#38489 = ORIENTED_EDGE ( 'NONE', *, *, #14085, .F. ) ; +#38490 = VERTEX_POINT ( 'NONE', #24215 ) ; +#38491 = FILL_AREA_STYLE_COLOUR ( '', #72746 ) ; +#38492 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100954 ) ; +#38493 = ORIENTED_EDGE ( 'NONE', *, *, #79287, .T. ) ; +#38494 = ORIENTED_EDGE ( 'NONE', *, *, #95647, .F. ) ; +#38496 = VERTEX_POINT ( 'NONE', #23690 ) ; +#38495 = LINE ( 'NONE', #40007, #14997 ) ; +#38497 = FILL_AREA_STYLE ('',( #7265 ) ) ; +#38498 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38499 = ORIENTED_EDGE ( 'NONE', *, *, #20931, .T. ) ; +#38501 = ADVANCED_FACE ( 'NONE', ( #78318 ), #41043, .T. ) ; +#38500 = SURFACE_SIDE_STYLE ('',( #30303 ) ) ; +#38502 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38503 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.7000000000000001776, -0.02000000000000000042 ) ) ; +#38504 = ORIENTED_EDGE ( 'NONE', *, *, #13714, .T. ) ; +#38505 = CARTESIAN_POINT ( 'NONE', ( 1.441319620083689967, -1.344945484192040075, 0.8299999999999999600 ) ) ; +#38506 = CARTESIAN_POINT ( 'NONE', ( 5.236461124874955964, 9.417844124874957146, 0.8991599999999999593 ) ) ; +#38507 = ORIENTED_EDGE ( 'NONE', *, *, #73745, .F. ) ; +#38509 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, -0.2250000000000000333 ) ) ; +#38508 = PRESENTATION_STYLE_ASSIGNMENT (( #69626 ) ) ; +#38510 = ORIENTED_EDGE ( 'NONE', *, *, #97559, .T. ) ; +#38511 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66215 ) ) ; +#38512 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77651 ) ) ; +#38513 = SURFACE_STYLE_USAGE ( .BOTH. , #14973 ) ; +#38514 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8648700000000000276 ) ) ; +#38515 = VECTOR ( 'NONE', #3852, 999.9999999999998863 ) ; +#38516 = FILL_AREA_STYLE ('',( #100180 ) ) ; +#38517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18974 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35623, #34613, #13032 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38518 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #64209, #81059, #34095, #25428 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38519 = VERTEX_POINT ( 'NONE', #15991 ) ; +#38520 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38521 = ORIENTED_EDGE ( 'NONE', *, *, #67130, .F. ) ; +#38522 = FACE_OUTER_BOUND ( 'NONE', #43617, .T. ) ; +#38523 = CARTESIAN_POINT ( 'NONE', ( -0.7996232790101961418, 0.5990488921811000234, 0.8100000000000000533 ) ) ; +#38524 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#38526 = EDGE_CURVE ( 'NONE', #55937, #95213, #39496, .T. ) ; +#38525 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#38527 = SURFACE_SIDE_STYLE ('',( #76820 ) ) ; +#38528 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#38529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48333 ) ) ; +#38530 = LINE ( 'NONE', #6309, #2321 ) ; +#38531 = SURFACE_STYLE_FILL_AREA ( #20696 ) ; +#38532 = DIRECTION ( 'NONE', ( -0.7071067811865479058, -0.7071067811865470176, 0.000000000000000000 ) ) ; +#38533 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38534 = ORIENTED_EDGE ( 'NONE', *, *, #25337, .T. ) ; +#38535 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#38537 = AXIS2_PLACEMENT_3D ( 'NONE', #87381, #40951, #93984 ) ; +#38536 = PLANE ( 'NONE', #54607 ) ; +#38539 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#38538 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38540 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#38541 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12072, 'distance_accuracy_value', 'NONE'); +#38542 = SURFACE_STYLE_FILL_AREA ( #83508 ) ; +#38543 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 2.544766999999999779, 0.8991599999999999593 ) ) ; +#38544 = VECTOR ( 'NONE', #18023, 1000.000000000000000 ) ; +#38545 = VECTOR ( 'NONE', #64046, 1000.000000000000000 ) ; +#38546 = CARTESIAN_POINT ( 'NONE', ( 3.794707603699269956E-16, 1.393372100993099938, 0.8299999999999999600 ) ) ; +#38547 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.000000000000000000 ) ) ; +#38548 = FILL_AREA_STYLE ('',( #62561 ) ) ; +#38549 = ORIENTED_EDGE ( 'NONE', *, *, #75241, .F. ) ; +#38550 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#38551 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#38552 = AXIS2_PLACEMENT_3D ( 'NONE', #11299, #51220, #83356 ) ; +#38553 = SURFACE_STYLE_USAGE ( .BOTH. , #61562 ) ; +#38554 = FILL_AREA_STYLE ('',( #76846 ) ) ; +#38555 = FILL_AREA_STYLE ('',( #29869 ) ) ; +#38556 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#38557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38558 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25537 ), #56603 ) ; +#38560 = STYLED_ITEM ( 'NONE', ( #1443 ), #49204 ) ; +#38559 = PLANE ( 'NONE', #94693 ) ; +#38561 = CYLINDRICAL_SURFACE ( 'NONE', #78566, 0.05000000000000012768 ) ; +#38562 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38563 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 15.15000000000000036, 0.000000000000000000 ) ) ; +#38564 = LINE ( 'NONE', #62579, #83086 ) ; +#38565 = FACE_OUTER_BOUND ( 'NONE', #96756, .T. ) ; +#38566 = SURFACE_SIDE_STYLE ('',( #30892 ) ) ; +#38568 = ADVANCED_FACE ( 'NONE', ( #64003 ), #32361, .T. ) ; +#38567 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38569 = LINE ( 'NONE', #47237, #89540 ) ; +#38570 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13649 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75500, #90313, #36216 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38571 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -2.000000000000000000, 0.000000000000000000 ) ) ; +#38572 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.449999999999999956, -13.35000000000000142 ) ) ; +#38573 = SURFACE_STYLE_USAGE ( .BOTH. , #77359 ) ; +#38574 = VERTEX_POINT ( 'NONE', #66015 ) ; +#38575 = LINE ( 'NONE', #92657, #92732 ) ; +#38576 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.000000000000000000 ) ) ; +#38577 = VECTOR ( 'NONE', #23478, 1000.000000000000000 ) ; +#38578 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38579 = DIRECTION ( 'NONE', ( -0.7071060119555145906, -0.7071075504167435577, 0.000000000000000000 ) ) ; +#38580 = FACE_OUTER_BOUND ( 'NONE', #60264, .T. ) ; +#38581 = VERTEX_POINT ( 'NONE', #74180 ) ; +#38582 = PLANE ( 'NONE', #51652 ) ; +#38583 = EDGE_CURVE ( 'NONE', #70873, #41891, #64393, .T. ) ; +#38584 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38585 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38586 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.166666666666666741, 0.000000000000000000 ) ) ; +#38587 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.900000000000000133, 1.009450051515179092E-78 ) ) ; +#38588 = PRESENTATION_STYLE_ASSIGNMENT (( #40117 ) ) ; +#38589 = VECTOR ( 'NONE', #57386, 1000.000000000000114 ) ; +#38590 = VERTEX_POINT ( 'NONE', #4224 ) ; +#38591 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48400 ), #97239 ) ; +#38592 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11411, 'distance_accuracy_value', 'NONE'); +#38593 = CARTESIAN_POINT ( 'NONE', ( -0.01471107728978500104, -1.407725713391660083, 0.8300000000000006262 ) ) ; +#38594 = VERTEX_POINT ( 'NONE', #96621 ) ; +#38595 = ORIENTED_EDGE ( 'NONE', *, *, #63945, .T. ) ; +#38596 = LINE ( 'NONE', #15062, #96095 ) ; +#38597 = LINE ( 'NONE', #78410, #13245 ) ; +#38598 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10583 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80560, #47381, #59103 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38599 = ORIENTED_EDGE ( 'NONE', *, *, #35045, .T. ) ; +#38600 = FILL_AREA_STYLE ('',( #69189 ) ) ; +#38601 = CARTESIAN_POINT ( 'NONE', ( 0.07744069998345409767, -1.407232784796780045, 0.8299999999999999600 ) ) ; +#38602 = STYLED_ITEM ( 'NONE', ( #74473 ), #73922 ) ; +#38603 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 1.474514954580256140E-18, 0.8499999999999999778 ) ) ; +#38604 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38605 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #5177, #47479 ) ; +#38606 = EDGE_CURVE ( 'NONE', #13962, #78282, #11782, .T. ) ; +#38607 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53138 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37306, #22983, #6572 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38608 = ORIENTED_EDGE ( 'NONE', *, *, #85353, .T. ) ; +#38609 = ORIENTED_EDGE ( 'NONE', *, *, #90982, .T. ) ; +#38610 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82648 ) ) ; +#38611 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48189, 'distance_accuracy_value', 'NONE'); +#38613 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38614 = ADVANCED_FACE ( 'NONE', ( #50719 ), #27736, .T. ) ; +#38615 = ORIENTED_EDGE ( 'NONE', *, *, #52697, .T. ) ; +#38616 = VECTOR ( 'NONE', #37071, 1000.000000000000114 ) ; +#38617 = SURFACE_STYLE_FILL_AREA ( #7388 ) ; +#38618 = FILL_AREA_STYLE ('',( #23312 ) ) ; +#38619 = ORIENTED_EDGE ( 'NONE', *, *, #78353, .T. ) ; +#38620 = CARTESIAN_POINT ( 'NONE', ( 0.1073457792207792999, 0.7099999999999999645, 0.1493506493506491228 ) ) ; +#38621 = ORIENTED_EDGE ( 'NONE', *, *, #7285, .T. ) ; +#38622 = ORIENTED_EDGE ( 'NONE', *, *, #38356, .F. ) ; +#38623 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38625 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38624 = LINE ( 'NONE', #62147, #3834 ) ; +#38626 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38627 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83705 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66664, #97768, #96783 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38628 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#38629 = VERTEX_POINT ( 'NONE', #27232 ) ; +#38630 = SURFACE_STYLE_USAGE ( .BOTH. , #29945 ) ; +#38631 = FILL_AREA_STYLE_COLOUR ( '', #27517 ) ; +#38632 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26675 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41720, #65693, #3422 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38633 = STYLED_ITEM ( 'NONE', ( #24818 ), #15938 ) ; +#38634 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38635 = PLANE ( 'NONE', #73469 ) ; +#38636 = ORIENTED_EDGE ( 'NONE', *, *, #16353, .F. ) ; +#38639 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38638 = VECTOR ( 'NONE', #18855, 1000.000000000000000 ) ; +#38637 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38640 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#38641 = ORIENTED_EDGE ( 'NONE', *, *, #19505, .F. ) ; +#38642 = ORIENTED_EDGE ( 'NONE', *, *, #33168, .F. ) ; +#38643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38644 = CLOSED_SHELL ( 'NONE', ( #117, #96770, #67991, #16307, #82437, #34813 ) ) ; +#38646 = PRESENTATION_STYLE_ASSIGNMENT (( #100797 ) ) ; +#38645 = CARTESIAN_POINT ( 'NONE', ( 1.001160189360249975, -1.432289833627879982, 0.8299999999999999600 ) ) ; +#38647 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38648 = CYLINDRICAL_SURFACE ( 'NONE', #59730, 0.4459546481032609644 ) ; +#38649 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38650 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25625 ), #15733 ) ; +#38651 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#38653 = EDGE_CURVE ( 'NONE', #14861, #17994, #88374, .T. ) ; +#38652 = CARTESIAN_POINT ( 'NONE', ( -0.01281341696057500083, -1.096743473147149928, 0.8100000000000000533 ) ) ; +#38654 = PLANE ( 'NONE', #29563 ) ; +#38655 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38656 = ORIENTED_EDGE ( 'NONE', *, *, #91595, .F. ) ; +#38657 = ORIENTED_EDGE ( 'NONE', *, *, #72760, .T. ) ; +#38658 = CARTESIAN_POINT ( 'NONE', ( 1.084944975536529910, -1.110638925478639960, 0.8100000000000000533 ) ) ; +#38659 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27178 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85948, #39997, #78306 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38660 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#38661 = SURFACE_STYLE_USAGE ( .BOTH. , #77454 ) ; +#38662 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38663 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38664 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38665 = ADVANCED_FACE ( 'NONE', ( #20035 ), #73673, .T. ) ; +#38666 = VERTEX_POINT ( 'NONE', #92473 ) ; +#38667 = EDGE_CURVE ( 'NONE', #39700, #11725, #85824, .T. ) ; +#38668 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38669 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 9.486769009248163798E-17, 0.6199999999999999956 ) ) ; +#38670 = FILL_AREA_STYLE ('',( #6936 ) ) ; +#38671 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45308 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19237, #66712, #34109 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38672 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#38673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38674 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38675 = LINE ( 'NONE', #32029, #35385 ) ; +#38676 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#38677 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38678 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#38679 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.100000000000000089, 0.1829999999999959714 ) ) ; +#38680 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38681 = SURFACE_STYLE_FILL_AREA ( #45299 ) ; +#38682 = FILL_AREA_STYLE_COLOUR ( '', #34041 ) ; +#38683 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78958, #16636, #24368, #8927 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38684 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#38686 = EDGE_CURVE ( 'NONE', #30846, #5892, #53205, .T. ) ; +#38685 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38687 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82718 ) ) ; +#38688 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11490 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75346, #50887, #19721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38689 = FILL_AREA_STYLE_COLOUR ( '', #59987 ) ; +#38690 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38691 = ORIENTED_EDGE ( 'NONE', *, *, #51334, .F. ) ; +#38692 = FILL_AREA_STYLE ('',( #14660 ) ) ; +#38693 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61116 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6697, #30750, #53751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38694 = SURFACE_STYLE_USAGE ( .BOTH. , #15161 ) ; +#38695 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333333304, 2.700000000000000178, 0.000000000000000000 ) ) ; +#38697 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#38696 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69723 ) ) ; +#38698 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38699 = CARTESIAN_POINT ( 'NONE', ( 1.092562546040373173, -1.116213578446475951, 0.8099999999999168976 ) ) ; +#38700 = EDGE_CURVE ( 'NONE', #97203, #92782, #76672, .T. ) ; +#38701 = SURFACE_STYLE_FILL_AREA ( #79027 ) ; +#38702 = FACE_OUTER_BOUND ( 'NONE', #78692, .T. ) ; +#38704 = EDGE_LOOP ( 'NONE', ( #29090, #81328, #97573, #51441 ) ) ; +#38703 = VECTOR ( 'NONE', #58452, 1000.000000000000000 ) ; +#38705 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63231 ) ) ; +#38706 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38707 = CARTESIAN_POINT ( 'NONE', ( 1.818404401970810103, -1.294636995308309890, 0.8299999999999994049 ) ) ; +#38708 = VECTOR ( 'NONE', #35465, 1000.000000000000000 ) ; +#38709 = FILL_AREA_STYLE ('',( #31555 ) ) ; +#38710 = VECTOR ( 'NONE', #5267, 1000.000000000000000 ) ; +#38711 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38712 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#38713 = CLOSED_SHELL ( 'NONE', ( #74492, #18618, #20397, #75899, #6239, #45665, #20708 ) ) ; +#38714 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, -3.388131789017201356E-18 ) ) ; +#38716 = STYLED_ITEM ( 'NONE', ( #24775 ), #40147 ) ; +#38715 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38717 = VERTEX_POINT ( 'NONE', #13824 ) ; +#38718 = ORIENTED_EDGE ( 'NONE', *, *, #75567, .F. ) ; +#38719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71304 ), #58307 ) ; +#38720 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#38721 = ORIENTED_EDGE ( 'NONE', *, *, #19055, .T. ) ; +#38722 = STYLED_ITEM ( 'NONE', ( #77707 ), #50347 ) ; +#38723 = SURFACE_SIDE_STYLE ('',( #7490 ) ) ; +#38724 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.000000000000000000 ) ) ; +#38725 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #39073 ) ; +#38726 = FILL_AREA_STYLE_COLOUR ( '', #308 ) ; +#38727 = ADVANCED_FACE ( 'NONE', ( #75668 ), #12814, .F. ) ; +#38729 = ORIENTED_EDGE ( 'NONE', *, *, #44517, .T. ) ; +#38728 = ORIENTED_EDGE ( 'NONE', *, *, #84853, .F. ) ; +#38730 = ORIENTED_EDGE ( 'NONE', *, *, #87592, .F. ) ; +#38731 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38732 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50529, 'distance_accuracy_value', 'NONE'); +#38733 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#38734 = LINE ( 'NONE', #70364, #94592 ) ; +#38735 = ORIENTED_EDGE ( 'NONE', *, *, #97328, .T. ) ; +#38736 = ADVANCED_FACE ( 'NONE', ( #36381 ), #6164, .T. ) ; +#38737 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#38738 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#38739 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92296 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5651, #12783, #21511 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38741 = FILL_AREA_STYLE_COLOUR ( '', #40213 ) ; +#38740 = SURFACE_SIDE_STYLE ('',( #94355 ) ) ; +#38743 = ORIENTED_EDGE ( 'NONE', *, *, #21381, .F. ) ; +#38742 = VECTOR ( 'NONE', #8137, 1000.000000000000114 ) ; +#38744 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#38745 = EDGE_LOOP ( 'NONE', ( #98411, #35540, #99891, #85547 ) ) ; +#38746 = ORIENTED_EDGE ( 'NONE', *, *, #87845, .T. ) ; +#38747 = LINE ( 'NONE', #958, #13335 ) ; +#38748 = VECTOR ( 'NONE', #18166, 1000.000000000000000 ) ; +#38749 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#38750 = FILL_AREA_STYLE ('',( #63279 ) ) ; +#38752 = ORIENTED_EDGE ( 'NONE', *, *, #15030, .T. ) ; +#38751 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38753 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38754 = AXIS2_PLACEMENT_3D ( 'NONE', #13480, #6811, #98745 ) ; +#38755 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38756 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#38757 = VERTEX_POINT ( 'NONE', #99558 ) ; +#38758 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#38759 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38760 = ORIENTED_EDGE ( 'NONE', *, *, #16145, .T. ) ; +#38761 = VERTEX_POINT ( 'NONE', #21058 ) ; +#38763 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38762 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#38764 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100649 ) ) ; +#38765 = SURFACE_STYLE_FILL_AREA ( #77063 ) ; +#38766 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#38767 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64796 ) ) ; +#38768 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#38769 = EDGE_CURVE ( 'NONE', #13072, #73519, #52222, .T. ) ; +#38770 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#38771 = LINE ( 'NONE', #91880, #86301 ) ; +#38774 = FACE_OUTER_BOUND ( 'NONE', #79059, .T. ) ; +#38773 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#38772 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8511, 'distance_accuracy_value', 'NONE'); +#38775 = CARTESIAN_POINT ( 'NONE', ( 0.3170313104546300109, -0.9034630071664919715, 0.8300000000000020695 ) ) ; +#38776 = VERTEX_POINT ( 'NONE', #5678 ) ; +#38777 = VECTOR ( 'NONE', #26660, 1000.000000000000000 ) ; +#38778 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8100000000000000533 ) ) ; +#38779 = VERTEX_POINT ( 'NONE', #94989 ) ; +#38780 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#38781 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38782 = VECTOR ( 'NONE', #47877, 1000.000000000000000 ) ; +#38783 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14235 ), #95828 ) ; +#38784 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92604 ) ) ; +#38786 = FACE_OUTER_BOUND ( 'NONE', #94912, .T. ) ; +#38785 = FACE_OUTER_BOUND ( 'NONE', #63978, .T. ) ; +#38787 = CARTESIAN_POINT ( 'NONE', ( 1.792693045999540047, -1.018845982455530041, 0.8299999999999999600 ) ) ; +#38788 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#38789 = CLOSED_SHELL ( 'NONE', ( #22035, #27141, #17022, #99455, #73787, #1446 ) ) ; +#38790 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38791 = EDGE_CURVE ( 'NONE', #90468, #51059, #63, .T. ) ; +#38792 = SURFACE_SIDE_STYLE ('',( #69912 ) ) ; +#38793 = EDGE_CURVE ( 'NONE', #59381, #57096, #31220, .T. ) ; +#38794 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38795 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#38796 = LINE ( 'NONE', #36418, #38926 ) ; +#38797 = FILL_AREA_STYLE ('',( #23486 ) ) ; +#38798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38799 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#38800 = FACE_OUTER_BOUND ( 'NONE', #67780, .T. ) ; +#38801 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38802 = VECTOR ( 'NONE', #24028, 1000.000000000000000 ) ; +#38804 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#38803 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#38805 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#38806 = DIRECTION ( 'NONE', ( -0.7071067811865465735, -0.7071067811865483499, 0.000000000000000000 ) ) ; +#38807 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43969 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13899, #69561, #37462 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38808 = EDGE_CURVE ( 'NONE', #2961, #31058, #87354, .T. ) ; +#38809 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86251, #33155, #47963, #47457 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38810 = VERTEX_POINT ( 'NONE', #1607 ) ; +#38811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38812 = PLANE ( 'NONE', #97539 ) ; +#38813 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5104, 'distance_accuracy_value', 'NONE'); +#38814 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76439, 'distance_accuracy_value', 'NONE'); +#38815 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.100000000000000089, -0.02000000000003353609 ) ) ; +#38816 = FACE_OUTER_BOUND ( 'NONE', #23032, .T. ) ; +#38817 = EDGE_CURVE ( 'NONE', #42167, #43131, #39892, .T. ) ; +#38818 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#38820 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#38819 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #16469, .NOT_KNOWN. ) ; +#38821 = AXIS2_PLACEMENT_3D ( 'NONE', #4576, #4094, #35771 ) ; +#38822 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38823 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#38824 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38825 = EDGE_CURVE ( 'NONE', #43086, #16737, #46517, .T. ) ; +#38826 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76347 ) ) ; +#38827 = ORIENTED_EDGE ( 'NONE', *, *, #45569, .T. ) ; +#38828 = EDGE_CURVE ( 'NONE', #35120, #74437, #54208, .T. ) ; +#38829 = ORIENTED_EDGE ( 'NONE', *, *, #71563, .T. ) ; +#38830 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62598, 'distance_accuracy_value', 'NONE'); +#38831 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18460, 'distance_accuracy_value', 'NONE'); +#38832 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38833 = SURFACE_SIDE_STYLE ('',( #7588 ) ) ; +#38834 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24208 ), #81288 ) ; +#38835 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#38836 = DIRECTION ( 'NONE', ( 0.7071067811865445751, 0.7071067811865504593, 0.000000000000000000 ) ) ; +#38837 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50330 ), #11049 ) ; +#38838 = VECTOR ( 'NONE', #16934, 1000.000000000000000 ) ; +#38839 = PRESENTATION_STYLE_ASSIGNMENT (( #8591 ) ) ; +#38840 = LINE ( 'NONE', #48009, #69669 ) ; +#38841 = SURFACE_SIDE_STYLE ('',( #29651 ) ) ; +#38842 = ORIENTED_EDGE ( 'NONE', *, *, #46719, .F. ) ; +#38844 = CARTESIAN_POINT ( 'NONE', ( 1.101360327800479988, -0.9762538161110779766, 0.8300000000000002931 ) ) ; +#38843 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#38845 = FILL_AREA_STYLE_COLOUR ( '', #31412 ) ; +#38846 = VERTEX_POINT ( 'NONE', #38884 ) ; +#38847 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#38848 = PLANE ( 'NONE', #89252 ) ; +#38849 = EDGE_LOOP ( 'NONE', ( #23824, #33068, #42862, #51318 ) ) ; +#38850 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38851 = CARTESIAN_POINT ( 'NONE', ( 1.050738163529689961, -1.365949044099890264, 0.8100000000000000533 ) ) ; +#38852 = SURFACE_SIDE_STYLE ('',( #60851 ) ) ; +#38853 = VECTOR ( 'NONE', #51341, 1000.000000000000000 ) ; +#38854 = EDGE_CURVE ( 'NONE', #63028, #43680, #55733, .T. ) ; +#38855 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38856 = CARTESIAN_POINT ( 'NONE', ( 0.05983570162738770237, 1.027996536205817879, 0.8099999999999998312 ) ) ; +#38858 = ORIENTED_EDGE ( 'NONE', *, *, #1413, .T. ) ; +#38857 = VERTEX_POINT ( 'NONE', #86864 ) ; +#38859 = PLANE ( 'NONE', #63774 ) ; +#38860 = EDGE_LOOP ( 'NONE', ( #42273, #93082, #68080, #94845 ) ) ; +#38861 = PRESENTATION_STYLE_ASSIGNMENT (( #15848 ) ) ; +#38862 = AXIS2_PLACEMENT_3D ( 'NONE', #35497, #66601, #91585 ) ; +#38863 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#38864 = CLOSED_SHELL ( 'NONE', ( #70292, #15168, #24763, #81940, #75756, #35377 ) ) ; +#38865 = ORIENTED_EDGE ( 'NONE', *, *, #97652, .F. ) ; +#38866 = ADVANCED_FACE ( 'NONE', ( #86349 ), #79202, .T. ) ; +#38867 = ORIENTED_EDGE ( 'NONE', *, *, #35822, .T. ) ; +#38868 = STYLED_ITEM ( 'NONE', ( #54158 ), #87973 ) ; +#38869 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155857000000000134, 0.8648700000000000276 ) ) ; +#38870 = FILL_AREA_STYLE_COLOUR ( '', #35143 ) ; +#38871 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38872 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38873 = ORIENTED_EDGE ( 'NONE', *, *, #30946, .F. ) ; +#38874 = ADVANCED_FACE ( 'NONE', ( #9670 ), #85328, .T. ) ; +#38875 = EDGE_LOOP ( 'NONE', ( #60382, #70276, #40459, #74951 ) ) ; +#38876 = FILL_AREA_STYLE ('',( #62889 ) ) ; +#38877 = VERTEX_POINT ( 'NONE', #3607 ) ; +#38878 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38879 = STYLED_ITEM ( 'NONE', ( #73820 ), #50072 ) ; +#38880 = EDGE_CURVE ( 'NONE', #92428, #87567, #81739, .T. ) ; +#38882 = VERTEX_POINT ( 'NONE', #80229 ) ; +#38881 = PRESENTATION_STYLE_ASSIGNMENT (( #7137 ) ) ; +#38883 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#38884 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.000000000000000000 ) ) ; +#38885 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 7.437945000000000917, 0.8648700000000000276 ) ) ; +#38886 = ORIENTED_EDGE ( 'NONE', *, *, #655, .F. ) ; +#38887 = CARTESIAN_POINT ( 'NONE', ( 6.544608750250088036, 2.721543249749913240, 0.8648700000000000276 ) ) ; +#38888 = LINE ( 'NONE', #1084, #42786 ) ; +#38889 = EDGE_LOOP ( 'NONE', ( #15711, #62265, #15590, #11930 ) ) ; +#38890 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#38891 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38892 = VERTEX_POINT ( 'NONE', #99009 ) ; +#38893 = AXIS2_PLACEMENT_3D ( 'NONE', #46314, #23902, #1411 ) ; +#38894 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14426 ) ) ; +#38895 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38897 = ORIENTED_EDGE ( 'NONE', *, *, #47780, .F. ) ; +#38896 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38898 = EDGE_CURVE ( 'NONE', #22641, #99643, #2607, .T. ) ; +#38899 = CARTESIAN_POINT ( 'NONE', ( 1.242240128911429986, -0.8869042198941200494, 0.8299999999999998490 ) ) ; +#38900 = LINE ( 'NONE', #93481, #66692 ) ; +#38901 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#38902 = STYLED_ITEM ( 'NONE', ( #70833 ), #31699 ) ; +#38903 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.000000000000000000 ) ) ; +#38904 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#38905 = ORIENTED_EDGE ( 'NONE', *, *, #22424, .F. ) ; +#38906 = PLANE ( 'NONE', #20690 ) ; +#38907 = AXIS2_PLACEMENT_3D ( 'NONE', #31585, #55102, #71396 ) ; +#38908 = STYLED_ITEM ( 'NONE', ( #80938 ), #84679 ) ; +#38909 = VECTOR ( 'NONE', #59081, 1000.000000000000000 ) ; +#38910 = LINE ( 'NONE', #40437, #97078 ) ; +#38911 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999993072, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#38912 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#38913 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69863 ) ) ; +#38914 = EDGE_CURVE ( 'NONE', #41763, #21399, #19925, .T. ) ; +#38915 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4531, #60213, #35721, #58706, #52036, #82661, #67321, #97916, #98392, #44326, #91319, #5985, #97445 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1249999999999991673, 0.2499999999999983347, 0.3749999999999992784, 0.4374999999999991673, 0.4999999999999991118, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#38916 = AXIS2_PLACEMENT_3D ( 'NONE', #89399, #88397, #65398 ) ; +#38917 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146550232, 0.5686465759269653253, 0.8100000000000000533 ) ) ; +#38918 = VERTEX_POINT ( 'NONE', #73053 ) ; +#38919 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#38920 = FILL_AREA_STYLE ('',( #86389 ) ) ; +#38921 = VECTOR ( 'NONE', #66399, 1000.000000000000114 ) ; +#38922 = ORIENTED_EDGE ( 'NONE', *, *, #75962, .F. ) ; +#38923 = SURFACE_SIDE_STYLE ('',( #14379 ) ) ; +#38924 = VECTOR ( 'NONE', #99611, 1000.000000000000000 ) ; +#38925 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, -3.099999999999980549, 0.000000000000000000 ) ) ; +#38926 = VECTOR ( 'NONE', #60424, 1000.000000000000000 ) ; +#38927 = FACE_OUTER_BOUND ( 'NONE', #36735, .T. ) ; +#38928 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38929 = AXIS2_PLACEMENT_3D ( 'NONE', #86608, #39643, #93717 ) ; +#38930 = ORIENTED_EDGE ( 'NONE', *, *, #29654, .F. ) ; +#38931 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.000000000000000000 ) ) ; +#38932 = SURFACE_SIDE_STYLE ('',( #23612 ) ) ; +#38933 = CARTESIAN_POINT ( 'NONE', ( -0.009862718265029700795, -1.085974092738730024, 0.8300000000000005151 ) ) ; +#38934 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909089635, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#38935 = DIRECTION ( 'NONE', ( -0.7071060119555145906, -0.7071075504167435577, 0.000000000000000000 ) ) ; +#38936 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#38937 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#38938 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#38939 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#38940 = CARTESIAN_POINT ( 'NONE', ( 0.06967798674591889341, -1.043958301690999901, 0.8299999999999999600 ) ) ; +#38941 = SURFACE_STYLE_FILL_AREA ( #30248 ) ; +#38942 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38005, 'distance_accuracy_value', 'NONE'); +#38943 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, 0.09999999999999999167, 0.8499999999999999778 ) ) ; +#38944 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53604 ) ) ; +#38945 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38946 = ORIENTED_EDGE ( 'NONE', *, *, #96966, .T. ) ; +#38947 = FILL_AREA_STYLE ('',( #53269 ) ) ; +#38948 = ADVANCED_FACE ( 'NONE', ( #33759 ), #58767, .T. ) ; +#38949 = EDGE_LOOP ( 'NONE', ( #60151, #11936, #23792, #96221 ) ) ; +#38950 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66416, 'distance_accuracy_value', 'NONE'); +#38952 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49451, 'distance_accuracy_value', 'NONE'); +#38953 = STYLED_ITEM ( 'NONE', ( #91323 ), #44132 ) ; +#38954 = FILL_AREA_STYLE ('',( #7708 ) ) ; +#38955 = FILL_AREA_STYLE ('',( #32304 ) ) ; +#38956 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#38957 = SURFACE_STYLE_USAGE ( .BOTH. , #45071 ) ; +#38958 = CARTESIAN_POINT ( 'NONE', ( 0.06988982237669021103, -1.070769809704489983, 0.8100000000000000533 ) ) ; +#38959 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#38960 = LINE ( 'NONE', #47110, #55894 ) ; +#38961 = EDGE_LOOP ( 'NONE', ( #45863, #3461, #71014, #25349 ) ) ; +#38962 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#38963 = LINE ( 'NONE', #70083, #68250 ) ; +#38964 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21302, 'distance_accuracy_value', 'NONE'); +#38965 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999334, 0.4245906043549200204, -0.01999999999999999695 ) ) ; +#38966 = EDGE_LOOP ( 'NONE', ( #29825, #3967, #53196, #87199 ) ) ; +#38967 = FILL_AREA_STYLE_COLOUR ( '', #13486 ) ; +#38968 = SURFACE_SIDE_STYLE ('',( #61469 ) ) ; +#38969 = AXIS2_PLACEMENT_3D ( 'NONE', #62142, #21289, #21789 ) ; +#38970 = ORIENTED_EDGE ( 'NONE', *, *, #18225, .F. ) ; +#38971 = CARTESIAN_POINT ( 'NONE', ( 2.300000000000000266, -3.123820061220055511, 0.000000000000000000 ) ) ; +#38972 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#38973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#38974 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999998446, -3.383333333333330195, 0.000000000000000000 ) ) ; +#38975 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38976 = FILL_AREA_STYLE ('',( #63493 ) ) ; +#38977 = ORIENTED_EDGE ( 'NONE', *, *, #36918, .F. ) ; +#38978 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78422 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91603, #20655, #11414 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38979 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#38980 = AXIS2_PLACEMENT_3D ( 'NONE', #77472, #70832, #47349 ) ; +#38981 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#38982 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75867, #29410, #43710 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#38983 = EDGE_CURVE ( 'NONE', #94608, #89914, #82230, .T. ) ; +#38984 = ORIENTED_EDGE ( 'NONE', *, *, #25147, .F. ) ; +#38985 = AXIS2_PLACEMENT_3D ( 'NONE', #14176, #52547, #90842 ) ; +#38986 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#38987 = SURFACE_STYLE_FILL_AREA ( #45581 ) ; +#38988 = FACE_OUTER_BOUND ( 'NONE', #98422, .T. ) ; +#38989 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999988010, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#38990 = FILL_AREA_STYLE_COLOUR ( '', #39456 ) ; +#38991 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#38992 = VERTEX_POINT ( 'NONE', #57771 ) ; +#38993 = ORIENTED_EDGE ( 'NONE', *, *, #43868, .F. ) ; +#38994 = ORIENTED_EDGE ( 'NONE', *, *, #78973, .F. ) ; +#38995 = STYLED_ITEM ( 'NONE', ( #60575 ), #25196 ) ; +#38996 = VECTOR ( 'NONE', #10465, 1000.000000000000000 ) ; +#38997 = AXIS2_PLACEMENT_3D ( 'NONE', #95909, #26013, #88286 ) ; +#38998 = EDGE_CURVE ( 'NONE', #13962, #11007, #43405, .T. ) ; +#38999 = ORIENTED_EDGE ( 'NONE', *, *, #53432, .F. ) ; +#39001 = ORIENTED_EDGE ( 'NONE', *, *, #81477, .T. ) ; +#39000 = SURFACE_STYLE_USAGE ( .BOTH. , #14954 ) ; +#39002 = DIRECTION ( 'NONE', ( -2.356961244533699997E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39003 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39004 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#39005 = EDGE_LOOP ( 'NONE', ( #27663, #70993, #75178, #22398 ) ) ; +#39006 = EDGE_CURVE ( 'NONE', #48425, #92204, #4274, .T. ) ; +#39007 = LINE ( 'NONE', #46645, #80969 ) ; +#39008 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39009 = ORIENTED_EDGE ( 'NONE', *, *, #67858, .F. ) ; +#39010 = PRESENTATION_STYLE_ASSIGNMENT (( #694 ) ) ; +#39011 = SURFACE_SIDE_STYLE ('',( #46122 ) ) ; +#39012 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 12.10755799999999915, 0.8648700000000000276 ) ) ; +#39013 = FACE_OUTER_BOUND ( 'NONE', #52471, .T. ) ; +#39014 = ORIENTED_EDGE ( 'NONE', *, *, #76651, .T. ) ; +#39015 = AXIS2_PLACEMENT_3D ( 'NONE', #56797, #56286, #79763 ) ; +#39017 = SURFACE_STYLE_FILL_AREA ( #23704 ) ; +#39016 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.100000000000000089 ) ) ; +#39018 = ORIENTED_EDGE ( 'NONE', *, *, #55651, .T. ) ; +#39019 = ADVANCED_FACE ( 'NONE', ( #42423 ), #41418, .T. ) ; +#39021 = ADVANCED_FACE ( 'NONE', ( #67385 ), #60758, .T. ) ; +#39020 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53541 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3792, #41113, #2305 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39022 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#39023 = LINE ( 'NONE', #62527, #53908 ) ; +#39025 = EDGE_CURVE ( 'NONE', #59891, #79701, #83230, .T. ) ; +#39024 = VECTOR ( 'NONE', #73390, 1000.000000000000000 ) ; +#39026 = CARTESIAN_POINT ( 'NONE', ( 0.1831366936980619864, -1.373561790606270039, 0.8299999999999982947 ) ) ; +#39027 = EDGE_CURVE ( 'NONE', #70019, #28141, #36271, .T. ) ; +#39028 = EDGE_LOOP ( 'NONE', ( #38622, #48980, #38510, #98875 ) ) ; +#39029 = SURFACE_SIDE_STYLE ('',( #86495 ) ) ; +#39030 = ORIENTED_EDGE ( 'NONE', *, *, #33471, .T. ) ; +#39031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39032 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999789573 ) ) ; +#39033 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#39034 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39035 = EDGE_CURVE ( 'NONE', #56736, #77676, #36760, .T. ) ; +#39036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74263, 'distance_accuracy_value', 'NONE'); +#39037 = FACE_OUTER_BOUND ( 'NONE', #30079, .T. ) ; +#39038 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000005745, 0.5199999999764691738, 0.6999285677606424949 ) ) ; +#39039 = EDGE_CURVE ( 'NONE', #741, #12243, #75555, .T. ) ; +#39040 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53375 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54850, #7760, #85963 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39041 = LINE ( 'NONE', #222, #82584 ) ; +#39042 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19440 ), #43919 ) ; +#39043 = EDGE_LOOP ( 'NONE', ( #73355, #22897, #59298, #88216, #49419, #86982, #19267, #100418, #28384, #67707 ) ) ; +#39044 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#39045 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#39047 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39046 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#39048 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70245 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15358, #53206, #100532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39050 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#39051 = VECTOR ( 'NONE', #41254, 1000.000000000000000 ) ; +#39052 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34089 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68060, #54286, #29290 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39053 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39054 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39055 = FACE_OUTER_BOUND ( 'NONE', #7278, .T. ) ; +#39056 = AXIS2_PLACEMENT_3D ( 'NONE', #89430, #19483, #63588 ) ; +#39057 = LINE ( 'NONE', #7812, #11887 ) ; +#39058 = ORIENTED_EDGE ( 'NONE', *, *, #20565, .F. ) ; +#39059 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39060 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39061 = CARTESIAN_POINT ( 'NONE', ( -0.01471107728978500104, -1.407725713391660083, 0.8299999999999999600 ) ) ; +#39062 = SURFACE_STYLE_FILL_AREA ( #31390 ) ; +#39063 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853417210, 1.551146575926969806, 0.8100000000000001643 ) ) ; +#39064 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42286 ) ) ; +#39065 = PLANE ( 'NONE', #56343 ) ; +#39066 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999334, 0.000000000000000000 ) ) ; +#39067 = SURFACE_STYLE_USAGE ( .BOTH. , #24791 ) ; +#39068 = SURFACE_STYLE_USAGE ( .BOTH. , #21724 ) ; +#39069 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39070 = FILL_AREA_STYLE ('',( #100714 ) ) ; +#39071 = VECTOR ( 'NONE', #40565, 1000.000000000000000 ) ; +#39072 = FACE_OUTER_BOUND ( 'NONE', #26465, .T. ) ; +#39073 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#39074 = LINE ( 'NONE', #100716, #25275 ) ; +#39075 = VERTEX_POINT ( 'NONE', #20934 ) ; +#39076 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81232, 'distance_accuracy_value', 'NONE'); +#39077 = CARTESIAN_POINT ( 'NONE', ( 1.162165579634195200, 1.329047116880149426, 0.8100000000000000533 ) ) ; +#39078 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8299999999999999600 ) ) ; +#39079 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39080 = LINE ( 'NONE', #62591, #14037 ) ; +#39082 = EDGE_CURVE ( 'NONE', #30580, #61258, #43317, .T. ) ; +#39081 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39083 = CARTESIAN_POINT ( 'NONE', ( -1.293111275392700099, -1.070174563215090080, 0.8299999999999999600 ) ) ; +#39084 = ORIENTED_EDGE ( 'NONE', *, *, #33641, .F. ) ; +#39085 = PLANE ( 'NONE', #4564 ) ; +#39086 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66531, 'distance_accuracy_value', 'NONE'); +#39087 = LINE ( 'NONE', #100238, #48720 ) ; +#39088 = STYLED_ITEM ( 'NONE', ( #15792 ), #51093 ) ; +#39089 = EDGE_LOOP ( 'NONE', ( #51583, #1203, #90204, #100256 ) ) ; +#39090 = SURFACE_STYLE_FILL_AREA ( #15567 ) ; +#39091 = LINE ( 'NONE', #1809, #69593 ) ; +#39092 = SURFACE_STYLE_FILL_AREA ( #46203 ) ; +#39093 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333320425, -1.100000000000000089, 1.747825839084689943E-76 ) ) ; +#39094 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, -9.880000000000000782, 0.2499999999999999445 ) ) ; +#39095 = FILL_AREA_STYLE ('',( #7358 ) ) ; +#39096 = FACE_OUTER_BOUND ( 'NONE', #56543, .T. ) ; +#39097 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #74232, #82408, #12357, #28274, #43565, #59454, #4765, #90550, #20588, #51764, #29748, #92519, #59946, #91048, #44559, #22607, #60932, #93004, #29268 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.493776705857645850E-05, 4.937248302705682986E-05, 7.331477681366326351E-05, 9.701993325366557762E-05, 0.0001201633963783112040, 0.0001426908098046762827, 0.0001647393961703094852, 0.0001865685712343216108, 0.0002082099287761440180, 0.0002296593890597375563, 0.0002512893635837115040, 0.0002733379499493446795, 0.0002960714739221180936, 0.0003197202093211288522, 0.0003446878849621242400, 0.0003712273557114769448 ), + .UNSPECIFIED. ) ; +#39098 = VERTEX_POINT ( 'NONE', #21426 ) ; +#39099 = FILL_AREA_STYLE ('',( #9383 ) ) ; +#39100 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39101 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19638, 'distance_accuracy_value', 'NONE'); +#39102 = ADVANCED_FACE ( 'NONE', ( #13191 ), #67864, .T. ) ; +#39103 = VERTEX_POINT ( 'NONE', #9045 ) ; +#39104 = CARTESIAN_POINT ( 'NONE', ( 0.7761769480519479236, 0.7099999999999999645, 0.1493506493506489285 ) ) ; +#39105 = ORIENTED_EDGE ( 'NONE', *, *, #24111, .F. ) ; +#39106 = LINE ( 'NONE', #23804, #55881 ) ; +#39107 = CARTESIAN_POINT ( 'NONE', ( 0.09306199881179780253, -1.350767436372750208, 0.8100000000000000533 ) ) ; +#39108 = PLANE ( 'NONE', #92294 ) ; +#39109 = FACE_OUTER_BOUND ( 'NONE', #65133, .T. ) ; +#39110 = STYLED_ITEM ( 'NONE', ( #53584 ), #85934 ) ; +#39111 = SURFACE_STYLE_FILL_AREA ( #99766 ) ; +#39112 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18112 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17772, #39253, #70387 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39113 = ORIENTED_EDGE ( 'NONE', *, *, #87246, .T. ) ; +#39115 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39114 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39116 = AXIS2_PLACEMENT_3D ( 'NONE', #82857, #52239, #13316 ) ; +#39117 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#39118 = SURFACE_STYLE_FILL_AREA ( #37630 ) ; +#39119 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39120 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39121 = EDGE_LOOP ( 'NONE', ( #59884, #65350, #29181, #24716, #29954, #7641 ) ) ; +#39122 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3410 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54307, #70619, #61490 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39123 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.5199999999686952812, 0.6999285677528677141 ) ) ; +#39124 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39125 = ORIENTED_EDGE ( 'NONE', *, *, #60034, .F. ) ; +#39126 = AXIS2_PLACEMENT_3D ( 'NONE', #96298, #88174, #66191 ) ; +#39127 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#39128 = ORIENTED_EDGE ( 'NONE', *, *, #45822, .T. ) ; +#39129 = VERTEX_POINT ( 'NONE', #77557 ) ; +#39130 = CARTESIAN_POINT ( 'NONE', ( 1.360085058678500047, -1.308270162923429902, 0.8100000000000000533 ) ) ; +#39132 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39131 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#39133 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96185 ) ) ; +#39134 = SURFACE_STYLE_USAGE ( .BOTH. , #319 ) ; +#39135 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83175 ), #53790 ) ; +#39136 = PRESENTATION_STYLE_ASSIGNMENT (( #7903 ) ) ; +#39137 = ORIENTED_EDGE ( 'NONE', *, *, #33978, .F. ) ; +#39138 = AXIS2_PLACEMENT_3D ( 'NONE', #8319, #24779, #25281 ) ; +#39139 = ADVANCED_FACE ( 'NONE', ( #47428 ), #94371, .T. ) ; +#39140 = FILL_AREA_STYLE ('',( #8916 ) ) ; +#39141 = SURFACE_SIDE_STYLE ('',( #23330 ) ) ; +#39142 = EDGE_LOOP ( 'NONE', ( #5437, #33346, #73616, #8021 ) ) ; +#39143 = ORIENTED_EDGE ( 'NONE', *, *, #33178, .F. ) ; +#39144 = ORIENTED_EDGE ( 'NONE', *, *, #55138, .F. ) ; +#39145 = FILL_AREA_STYLE ('',( #7914 ) ) ; +#39146 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39147 = PLANE ( 'NONE', #44991 ) ; +#39148 = FILL_AREA_STYLE_COLOUR ( '', #96438 ) ; +#39149 = CARTESIAN_POINT ( 'NONE', ( -0.03429546097047749681, -1.132325613921520091, 0.8299999999999999600 ) ) ; +#39151 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39150 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44035 ), #1643 ) ; +#39152 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39153 = ADVANCED_FACE ( 'NONE', ( #24487 ), #46389, .T. ) ; +#39154 = PLANE ( 'NONE', #74419 ) ; +#39155 = ORIENTED_EDGE ( 'NONE', *, *, #67826, .F. ) ; +#39156 = PLANE ( 'NONE', #37863 ) ; +#39157 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39158 = FACE_OUTER_BOUND ( 'NONE', #42012, .T. ) ; +#39159 = PRESENTATION_STYLE_ASSIGNMENT (( #62179 ) ) ; +#39160 = PRESENTATION_STYLE_ASSIGNMENT (( #47327 ) ) ; +#39161 = SURFACE_SIDE_STYLE ('',( #84626 ) ) ; +#39162 = FACE_OUTER_BOUND ( 'NONE', #7635, .T. ) ; +#39163 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39164 = ORIENTED_EDGE ( 'NONE', *, *, #25922, .T. ) ; +#39165 = FILL_AREA_STYLE_COLOUR ( '', #42302 ) ; +#39166 = DIRECTION ( 'NONE', ( 0.7071075504167435577, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#39167 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39168 = FACE_OUTER_BOUND ( 'NONE', #18803, .T. ) ; +#39169 = LINE ( 'NONE', #69794, #87596 ) ; +#39170 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852913999999998840, 0.8991599999999999593 ) ) ; +#39171 = LINE ( 'NONE', #56039, #49694 ) ; +#39172 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57474, 'distance_accuracy_value', 'NONE'); +#39173 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#39174 = FILL_AREA_STYLE_COLOUR ( '', #26974 ) ; +#39175 = STYLED_ITEM ( 'NONE', ( #42180 ), #86259 ) ; +#39176 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#39178 = EDGE_CURVE ( 'NONE', #29476, #22813, #16242, .T. ) ; +#39177 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24138 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42935, #60799, #6076 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39179 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39180 = LINE ( 'NONE', #70319, #89159 ) ; +#39181 = PLANE ( 'NONE', #53703 ) ; +#39182 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39183 = DIRECTION ( 'NONE', ( 0.7071045084557405769, -0.7071090539100497452, 0.000000000000000000 ) ) ; +#39184 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32721 ) ) ; +#39185 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62612 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21027, #96592, #26698 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39186 = FILL_AREA_STYLE_COLOUR ( '', #100759 ) ; +#39187 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4912 ), #84802 ) ; +#39188 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #17573, 'design' ) ; +#39190 = EDGE_CURVE ( 'NONE', #14217, #29318, #39252, .T. ) ; +#39189 = FACE_OUTER_BOUND ( 'NONE', #23201, .T. ) ; +#39191 = PLANE ( 'NONE', #1946 ) ; +#39192 = VERTEX_POINT ( 'NONE', #73938 ) ; +#39193 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#39194 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39195 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39196 = CARTESIAN_POINT ( 'NONE', ( 1.575220826706200006, -1.366783821657739928, 0.8299999999999977396 ) ) ; +#39197 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90889, 'distance_accuracy_value', 'NONE'); +#39198 = CARTESIAN_POINT ( 'NONE', ( -0.08371903756181429956, -1.220939016933670018, 0.8300000000000002931 ) ) ; +#39199 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39200 = AXIS2_PLACEMENT_3D ( 'NONE', #1882, #25881, #1373 ) ; +#39201 = ORIENTED_EDGE ( 'NONE', *, *, #6984, .F. ) ; +#39202 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39203 = AXIS2_PLACEMENT_3D ( 'NONE', #27343, #37395, #3353 ) ; +#39204 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58793 ) ) ; +#39205 = CARTESIAN_POINT ( 'NONE', ( 1.795983389471520031, -1.255590633215009966, 0.8299999999999994049 ) ) ; +#39206 = DIRECTION ( 'NONE', ( -0.7071067811865483499, 0.7071067811865467956, 0.000000000000000000 ) ) ; +#39207 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88052, 'distance_accuracy_value', 'NONE'); +#39208 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95572, 'distance_accuracy_value', 'NONE'); +#39209 = SURFACE_STYLE_USAGE ( .BOTH. , #85675 ) ; +#39210 = ADVANCED_FACE ( 'NONE', ( #64259 ), #27845, .F. ) ; +#39211 = ORIENTED_EDGE ( 'NONE', *, *, #37492, .T. ) ; +#39212 = ORIENTED_EDGE ( 'NONE', *, *, #87584, .T. ) ; +#39213 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#39214 = ORIENTED_EDGE ( 'NONE', *, *, #9315, .T. ) ; +#39216 = CARTESIAN_POINT ( 'NONE', ( -0.2991008533676399739, -1.396584910994119966, 0.8299999999999999600 ) ) ; +#39215 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29389 ) ) ; +#39217 = EDGE_CURVE ( 'NONE', #87717, #11229, #72692, .T. ) ; +#39218 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#39219 = LINE ( 'NONE', #68827, #4310 ) ; +#39220 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20083, 'distance_accuracy_value', 'NONE'); +#39221 = FILL_AREA_STYLE ('',( #23408 ) ) ; +#39222 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #75595 ) ; +#39223 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39225 = ORIENTED_EDGE ( 'NONE', *, *, #93970, .T. ) ; +#39224 = ORIENTED_EDGE ( 'NONE', *, *, #99317, .T. ) ; +#39226 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41861 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80813, #73138, #50187 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39227 = EDGE_LOOP ( 'NONE', ( #10587, #43115, #7210, #13279 ) ) ; +#39228 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39229 = CARTESIAN_POINT ( 'NONE', ( 0.6761799387799150018, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#39230 = ORIENTED_EDGE ( 'NONE', *, *, #97835, .F. ) ; +#39231 = EDGE_CURVE ( 'NONE', #50880, #89842, #33119, .T. ) ; +#39232 = ADVANCED_FACE ( 'NONE', ( #66759 ), #75930, .T. ) ; +#39233 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8991599999999999593 ) ) ; +#39234 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4965 ) ) ; +#39235 = AXIS2_PLACEMENT_3D ( 'NONE', #39983, #46080, #71122 ) ; +#39236 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#39237 = VERTEX_POINT ( 'NONE', #27996 ) ; +#39238 = CARTESIAN_POINT ( 'NONE', ( -0.4563726483146510193, -1.022509610276640002, 0.8100000000000000533 ) ) ; +#39239 = ORIENTED_EDGE ( 'NONE', *, *, #20565, .T. ) ; +#39240 = VERTEX_POINT ( 'NONE', #59158 ) ; +#39241 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#39242 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93093, #91132, #22693 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39243 = STYLED_ITEM ( 'NONE', ( #40036 ), #93734 ) ; +#39244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39245 = VECTOR ( 'NONE', #96755, 1000.000000000000000 ) ; +#39247 = EDGE_LOOP ( 'NONE', ( #78122, #96962, #78188, #96054, #34766, #69341, #58808, #62963, #73636, #87553, #21609, #46226 ) ) ; +#39246 = SURFACE_STYLE_USAGE ( .BOTH. , #77553 ) ; +#39248 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13089 ), #34414 ) ; +#39249 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.383333333333323090, 0.000000000000000000 ) ) ; +#39250 = ADVANCED_FACE ( 'NONE', ( #83106 ), #90245, .F. ) ; +#39251 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4982 ), #34415 ) ; +#39252 = LINE ( 'NONE', #46901, #46573 ) ; +#39253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39254 = ORIENTED_EDGE ( 'NONE', *, *, #38468, .F. ) ; +#39255 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#39256 = EDGE_LOOP ( 'NONE', ( #61745, #71915, #97945, #10106 ) ) ; +#39257 = ORIENTED_EDGE ( 'NONE', *, *, #35597, .T. ) ; +#39259 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39258 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39260 = STYLED_ITEM ( 'NONE', ( #79571 ), #6820 ) ; +#39261 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39262 = CARTESIAN_POINT ( 'NONE', ( -0.5075789211564899484, -1.256245978568790056, 0.8100000000000000533 ) ) ; +#39263 = EDGE_CURVE ( 'NONE', #90881, #5141, #4954, .T. ) ; +#39264 = CARTESIAN_POINT ( 'NONE', ( 0.2164741715418609935, -0.9593045227066020475, 0.8300000000000020695 ) ) ; +#39265 = ORIENTED_EDGE ( 'NONE', *, *, #24782, .T. ) ; +#39266 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39267 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27873 ), #84887 ) ; +#39268 = LINE ( 'NONE', #465, #61016 ) ; +#39269 = ORIENTED_EDGE ( 'NONE', *, *, #33216, .F. ) ; +#39270 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#39271 = FACE_OUTER_BOUND ( 'NONE', #85098, .T. ) ; +#39272 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 1.306104834247010004E-29 ) ) ; +#39273 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39274 = SURFACE_SIDE_STYLE ('',( #30586 ) ) ; +#39275 = FILL_AREA_STYLE_COLOUR ( '', #30804 ) ; +#39276 = LINE ( 'NONE', #25508, #10833 ) ; +#39277 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72021, 'distance_accuracy_value', 'NONE'); +#39278 = SURFACE_STYLE_USAGE ( .BOTH. , #46936 ) ; +#39279 = CARTESIAN_POINT ( 'NONE', ( 0.9400000000000000577, -9.880000000000000782, 0.2999999999999999889 ) ) ; +#39280 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39281 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 10.54921500000000023, 0.8648700000000000276 ) ) ; +#39282 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#39283 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #149 ) ) ; +#39284 = EDGE_CURVE ( 'NONE', #26081, #54091, #59106, .T. ) ; +#39285 = FILL_AREA_STYLE ('',( #17310 ) ) ; +#39286 = FILL_AREA_STYLE ('',( #78110 ) ) ; +#39287 = VECTOR ( 'NONE', #47908, 1000.000000000000000 ) ; +#39288 = AXIS2_PLACEMENT_3D ( 'NONE', #22022, #13277, #37374 ) ; +#39289 = EDGE_CURVE ( 'NONE', #27262, #65972, #99330, .T. ) ; +#39290 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39292 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39291 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39293 = FILL_AREA_STYLE ('',( #55662 ) ) ; +#39294 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39295 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39296 = PLANE ( 'NONE', #52802 ) ; +#39297 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75148, 'distance_accuracy_value', 'NONE'); +#39298 = ORIENTED_EDGE ( 'NONE', *, *, #53810, .T. ) ; +#39300 = EDGE_CURVE ( 'NONE', #6999, #1743, #98333, .T. ) ; +#39299 = FILL_AREA_STYLE ('',( #71979 ) ) ; +#39301 = ORIENTED_EDGE ( 'NONE', *, *, #82821, .T. ) ; +#39302 = DIRECTION ( 'NONE', ( 2.914335439641030002E-16, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#39303 = FILL_AREA_STYLE_COLOUR ( '', #62427 ) ; +#39304 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#39305 = SURFACE_STYLE_USAGE ( .BOTH. , #62318 ) ; +#39306 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82072 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100673, #69106, #99685 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39307 = SURFACE_STYLE_USAGE ( .BOTH. , #8082 ) ; +#39308 = FILL_AREA_STYLE_COLOUR ( '', #65214 ) ; +#39309 = SURFACE_SIDE_STYLE ('',( #85269 ) ) ; +#39310 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100932 ) ; +#39311 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39312 = AXIS2_PLACEMENT_3D ( 'NONE', #95669, #3284, #41097 ) ; +#39313 = VERTEX_POINT ( 'NONE', #67749 ) ; +#39314 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39315 = VERTEX_POINT ( 'NONE', #43780 ) ; +#39316 = FILL_AREA_STYLE ('',( #61831 ) ) ; +#39317 = VECTOR ( 'NONE', #60778, 1000.000000000000000 ) ; +#39318 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39319 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#39320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39321 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853422761, 1.377634075926969626, 0.8100000000000000533 ) ) ; +#39322 = ORIENTED_EDGE ( 'NONE', *, *, #64055, .T. ) ; +#39323 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#39324 = FILL_AREA_STYLE_COLOUR ( '', #30795 ) ; +#39325 = STYLED_ITEM ( 'NONE', ( #51324 ), #7245 ) ; +#39326 = ORIENTED_EDGE ( 'NONE', *, *, #275, .F. ) ; +#39327 = FILL_AREA_STYLE_COLOUR ( '', #2814 ) ; +#39328 = AXIS2_PLACEMENT_3D ( 'NONE', #23785, #55943, #47249 ) ; +#39329 = VERTEX_POINT ( 'NONE', #98824 ) ; +#39330 = EDGE_CURVE ( 'NONE', #25544, #98407, #29470, .T. ) ; +#39331 = EDGE_CURVE ( 'NONE', #55619, #76382, #29946, .T. ) ; +#39332 = CARTESIAN_POINT ( 'NONE', ( 1.044215815879510068, -1.351519064127929992, 0.8100000000000000533 ) ) ; +#39333 = LINE ( 'NONE', #21141, #35245 ) ; +#39334 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39335 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39336 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39337 = CARTESIAN_POINT ( 'NONE', ( 1.826762951391289969, -1.165682221622120096, 0.8299999999999999600 ) ) ; +#39338 = PRESENTATION_STYLE_ASSIGNMENT (( #30 ) ) ; +#39339 = FILL_AREA_STYLE ('',( #62869 ) ) ; +#39341 = ORIENTED_EDGE ( 'NONE', *, *, #5903, .T. ) ; +#39340 = EDGE_LOOP ( 'NONE', ( #50186, #37861, #3707, #87897 ) ) ; +#39342 = STYLED_ITEM ( 'NONE', ( #44868 ), #69659 ) ; +#39343 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999996669, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#39344 = ORIENTED_EDGE ( 'NONE', *, *, #69536, .T. ) ; +#39346 = FILL_AREA_STYLE ('',( #94474 ) ) ; +#39345 = SURFACE_SIDE_STYLE ('',( #78174 ) ) ; +#39347 = ORIENTED_EDGE ( 'NONE', *, *, #59691, .T. ) ; +#39348 = ADVANCED_FACE ( 'NONE', ( #52979 ), #6428, .F. ) ; +#39349 = ORIENTED_EDGE ( 'NONE', *, *, #39190, .T. ) ; +#39350 = EDGE_CURVE ( 'NONE', #16540, #12418, #6899, .T. ) ; +#39351 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, 0.000000000000000000 ) ) ; +#39352 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666653285, 0.8999999999999990230, 3.495651678170078205E-76 ) ) ; +#39353 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#39354 = CARTESIAN_POINT ( 'NONE', ( -0.1634999987230950080, -0.9726617844338850682, 0.8300000000000000711 ) ) ; +#39355 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57334 ), #6640 ) ; +#39357 = CYLINDRICAL_SURFACE ( 'NONE', #98847, 0.09999999999999939493 ) ; +#39356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39358 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#39359 = VERTEX_POINT ( 'NONE', #47300 ) ; +#39360 = EDGE_CURVE ( 'NONE', #71777, #48425, #16127, .T. ) ; +#39361 = ORIENTED_EDGE ( 'NONE', *, *, #55534, .T. ) ; +#39362 = PRESENTATION_STYLE_ASSIGNMENT (( #69483 ) ) ; +#39363 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39364 = EDGE_LOOP ( 'NONE', ( #98609, #50341, #53096, #16248 ) ) ; +#39365 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8648700000000000276 ) ) ; +#39366 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #90851, #91827, #21393, #44847, #83698, #11639, #81707, #35254, #68349, #5040, #99411, #60724, #36240, #42880, #4558, #74027 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000000555, 0.1875000000000000833, 0.2500000000000001110, 0.4999999999999999445, 0.6249999999999995559, 0.6874999999999996669, 0.7499999999999996669, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#39367 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16562 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4805, #59503, #92080 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39368 = ORIENTED_EDGE ( 'NONE', *, *, #1468, .F. ) ; +#39369 = EDGE_CURVE ( 'NONE', #10525, #73738, #93219, .T. ) ; +#39370 = PLANE ( 'NONE', #62964 ) ; +#39371 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#39372 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#39373 = VERTEX_POINT ( 'NONE', #65025 ) ; +#39374 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39375 = EDGE_LOOP ( 'NONE', ( #82738, #90451, #73314, #1987 ) ) ; +#39376 = ADVANCED_FACE ( 'NONE', ( #326 ), #84592, .F. ) ; +#39377 = SURFACE_STYLE_USAGE ( .BOTH. , #10157 ) ; +#39378 = VECTOR ( 'NONE', #591, 1000.000000000000000 ) ; +#39379 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57423 ), #23217 ) ; +#39380 = FILL_AREA_STYLE ('',( #96002 ) ) ; +#39381 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.05000000000000002359, 0.1900000000000000022 ) ) ; +#39383 = ORIENTED_EDGE ( 'NONE', *, *, #90764, .F. ) ; +#39382 = CARTESIAN_POINT ( 'NONE', ( -0.4373985389610389740, 0.6899999999999999467, -1.355252715606880543E-17 ) ) ; +#39384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91210 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78964, #49338, #88630 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39385 = CARTESIAN_POINT ( 'NONE', ( -0.7175359621965019530, 1.464383040805290026, 0.8299999999999999600 ) ) ; +#39386 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39387 = EDGE_CURVE ( 'NONE', #24100, #39359, #86609, .T. ) ; +#39388 = STYLED_ITEM ( 'NONE', ( #44081 ), #95615 ) ; +#39389 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 3.831700999999999802, 0.8648700000000000276 ) ) ; +#39390 = EDGE_CURVE ( 'NONE', #81738, #2862, #85094, .T. ) ; +#39391 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39392 = ORIENTED_EDGE ( 'NONE', *, *, #28202, .F. ) ; +#39393 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#39394 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999223, 0.2399999999999999911 ) ) ; +#39395 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83443 ) ) ; +#39396 = FILL_AREA_STYLE ('',( #77704 ) ) ; +#39397 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#39398 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39399 = FILL_AREA_STYLE_COLOUR ( '', #9471 ) ; +#39400 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#39401 = SURFACE_SIDE_STYLE ('',( #69010 ) ) ; +#39402 = AXIS2_PLACEMENT_3D ( 'NONE', #81367, #41041, #9282 ) ; +#39403 = VECTOR ( 'NONE', #85147, 1000.000000000000114 ) ; +#39404 = ORIENTED_EDGE ( 'NONE', *, *, #50718, .F. ) ; +#39405 = PLANE ( 'NONE', #35235 ) ; +#39406 = EDGE_LOOP ( 'NONE', ( #83564, #70643, #45445, #64881, #92910, #13877 ) ) ; +#39407 = VECTOR ( 'NONE', #265, 1000.000000000000000 ) ; +#39408 = EDGE_CURVE ( 'NONE', #2068, #75526, #55290, .T. ) ; +#39409 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#39410 = AXIS2_PLACEMENT_3D ( 'NONE', #69187, #30400, #85556 ) ; +#39411 = FACE_OUTER_BOUND ( 'NONE', #19361, .T. ) ; +#39412 = VECTOR ( 'NONE', #73796, 1000.000000000000000 ) ; +#39413 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39414 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 2.100000000000000089, -0.02000000000000419845 ) ) ; +#39415 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#39416 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10042 ), #98101 ) ; +#39417 = ORIENTED_EDGE ( 'NONE', *, *, #40682, .F. ) ; +#39418 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.05000000000000001665, 0.1900000000000000022 ) ) ; +#39419 = EDGE_CURVE ( 'NONE', #22958, #64829, #89101, .T. ) ; +#39420 = LINE ( 'NONE', #84872, #25085 ) ; +#39421 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999995261, -0.1458578643762691029 ) ) ; +#39422 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39423 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39424 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39425 = FILL_AREA_STYLE ('',( #78253 ) ) ; +#39426 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.123820061220045297, 0.000000000000000000 ) ) ; +#39427 = SURFACE_STYLE_USAGE ( .BOTH. , #100579 ) ; +#39428 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94806 ), #41068 ) ; +#39429 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39430 = EDGE_CURVE ( 'NONE', #89842, #42889, #65035, .T. ) ; +#39431 = SURFACE_STYLE_USAGE ( .BOTH. , #77736 ) ; +#39432 = SURFACE_SIDE_STYLE ('',( #78257 ) ) ; +#39433 = CARTESIAN_POINT ( 'NONE', ( 0.04906375505614529731, -0.9758031678253580310, 0.8100000000000000533 ) ) ; +#39434 = STYLED_ITEM ( 'NONE', ( #25591 ), #46802 ) ; +#39435 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#39436 = FILL_AREA_STYLE ('',( #96053 ) ) ; +#39437 = ORIENTED_EDGE ( 'NONE', *, *, #10792, .F. ) ; +#39438 = ADVANCED_FACE ( 'NONE', ( #69758 ), #73202, .T. ) ; +#39439 = ORIENTED_EDGE ( 'NONE', *, *, #18825, .F. ) ; +#39440 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39441 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39442 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39443 = LINE ( 'NONE', #23139, #64230 ) ; +#39444 = SURFACE_SIDE_STYLE ('',( #85910 ) ) ; +#39445 = LINE ( 'NONE', #85913, #14583 ) ; +#39446 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#39447 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#39448 = LINE ( 'NONE', #61959, #12863 ) ; +#39449 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.123820061220085265, 0.000000000000000000 ) ) ; +#39450 = ORIENTED_EDGE ( 'NONE', *, *, #54144, .T. ) ; +#39451 = FACE_OUTER_BOUND ( 'NONE', #88702, .T. ) ; +#39452 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#39453 = ORIENTED_EDGE ( 'NONE', *, *, #87382, .F. ) ; +#39454 = CARTESIAN_POINT ( 'NONE', ( 1.280736033769998672, -1.245286356562288699, 0.8099999999998355182 ) ) ; +#39455 = AXIS2_PLACEMENT_3D ( 'NONE', #2895, #34047, #71829 ) ; +#39456 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39457 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39458 = ORIENTED_EDGE ( 'NONE', *, *, #56809, .F. ) ; +#39459 = DIRECTION ( 'NONE', ( -0.9390355371548172458, 0.000000000000000000, -0.3438200982495990821 ) ) ; +#39460 = EDGE_CURVE ( 'NONE', #50063, #30781, #23611, .T. ) ; +#39461 = EDGE_CURVE ( 'NONE', #48033, #51489, #73688, .T. ) ; +#39462 = VECTOR ( 'NONE', #19177, 1000.000000000000114 ) ; +#39463 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39464 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39465 = VECTOR ( 'NONE', #76480, 1000.000000000000000 ) ; +#39466 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#39467 = PLANE ( 'NONE', #67014 ) ; +#39468 = PRESENTATION_STYLE_ASSIGNMENT (( #46612 ) ) ; +#39469 = SURFACE_STYLE_FILL_AREA ( #47643 ) ; +#39470 = EDGE_LOOP ( 'NONE', ( #60162, #64047, #77319, #9754 ) ) ; +#39471 = AXIS2_PLACEMENT_3D ( 'NONE', #23684, #53813, #62499 ) ; +#39472 = VECTOR ( 'NONE', #31632, 1000.000000000000000 ) ; +#39473 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 8.569316000000000599, 0.8648700000000000276 ) ) ; +#39474 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86711 ) ) ; +#39475 = VECTOR ( 'NONE', #73066, 1000.000000000000114 ) ; +#39476 = EDGE_CURVE ( 'NONE', #100207, #39853, #92859, .T. ) ; +#39477 = ORIENTED_EDGE ( 'NONE', *, *, #56348, .F. ) ; +#39478 = EDGE_CURVE ( 'NONE', #13813, #56115, #93860, .T. ) ; +#39479 = FACE_OUTER_BOUND ( 'NONE', #41352, .T. ) ; +#39480 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39481 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39482 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39483 = FILL_AREA_STYLE_COLOUR ( '', #1060 ) ; +#39484 = EDGE_LOOP ( 'NONE', ( #11761, #49601, #40158, #10308 ) ) ; +#39485 = ORIENTED_EDGE ( 'NONE', *, *, #17167, .T. ) ; +#39486 = SURFACE_SIDE_STYLE ('',( #16468 ) ) ; +#39487 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #26613, #73566, #27121, #88887, #74579, #42918, #87869, #58284, #65379, #18916, #96005, #10673, #50111, #97005, #81253, #74066, #89382, #89876, #10159, #11177, #4116, #4598, #3619, #34789, #41429, #65913, #26113, #19432, #43417, #50609, #35297 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.469891172885785737E-05, 2.837247054050074396E-05, 4.118507935592018393E-05, 5.372706464234971660E-05, 6.650062454123555804E-05, 7.950671947744166162E-05, 9.319155633876410210E-05, 0.0001076114340513762048, 0.0001227165621414977748, 0.0001383963279910565094, 0.0001548135506474084585, 0.0001718948309940213884, 0.0002071828797828611287, 0.0002430624189904889221, 0.0002791349300522562933, 0.0003149324747077262253, 0.0003324498852058400131, 0.0003494012154680959455, 0.0003659898241424219454, 0.0003821226701214126093, 0.0003979326149519609736, 0.0004135471195642111825, 0.0004289298359167463440, 0.0004446306713806961043, 0.0004607306973406561008, 0.0004777166628339197412, 0.0004958116794663855811, 0.0005154722711624770215 ), + .UNSPECIFIED. ) ; +#39488 = VERTEX_POINT ( 'NONE', #24002 ) ; +#39489 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26540 ), #59148 ) ; +#39490 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94856 ) ) ; +#39491 = VERTEX_POINT ( 'NONE', #53117 ) ; +#39493 = ORIENTED_EDGE ( 'NONE', *, *, #96123, .T. ) ; +#39492 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39494 = LINE ( 'NONE', #14956, #80117 ) ; +#39495 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39496 = LINE ( 'NONE', #40534, #77413 ) ; +#39497 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#39498 = AXIS2_PLACEMENT_3D ( 'NONE', #82799, #98037, #50679 ) ; +#39499 = ORIENTED_EDGE ( 'NONE', *, *, #40999, .T. ) ; +#39500 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39501 = LINE ( 'NONE', #78809, #32881 ) ; +#39502 = ORIENTED_EDGE ( 'NONE', *, *, #18447, .T. ) ; +#39503 = SURFACE_STYLE_USAGE ( .BOTH. , #31844 ) ; +#39504 = EDGE_CURVE ( 'NONE', #94479, #34477, #95933, .T. ) ; +#39505 = PRESENTATION_STYLE_ASSIGNMENT (( #52829 ) ) ; +#39506 = VECTOR ( 'NONE', #55410, 1000.000000000000000 ) ; +#39507 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#39508 = VECTOR ( 'NONE', #2166, 1000.000000000000000 ) ; +#39509 = ORIENTED_EDGE ( 'NONE', *, *, #87992, .T. ) ; +#39511 = SURFACE_SIDE_STYLE ('',( #39017 ) ) ; +#39510 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.000000000000000000 ) ) ; +#39512 = ORIENTED_EDGE ( 'NONE', *, *, #88835, .F. ) ; +#39513 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73786 ), #52579 ) ; +#39514 = ADVANCED_FACE ( 'NONE', ( #70411 ), #45400, .T. ) ; +#39515 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39516 = CYLINDRICAL_SURFACE ( 'NONE', #89759, 0.01000000000000002623 ) ; +#39518 = ADVANCED_FACE ( 'NONE', ( #39797 ), #61299, .T. ) ; +#39517 = FILL_AREA_STYLE ('',( #86491 ) ) ; +#39519 = CIRCLE ( 'NONE', #57484, 0.009999999999999998473 ) ; +#39520 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.9238200612200849760, -0.02000000000000000042 ) ) ; +#39521 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999999112, 0.6700000000000000400, 0.1999999999999998723 ) ) ; +#39522 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87069 ) ) ; +#39523 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51003 ) ) ; +#39524 = VERTEX_POINT ( 'NONE', #7550 ) ; +#39526 = FILL_AREA_STYLE_COLOUR ( '', #78456 ) ; +#39525 = CYLINDRICAL_SURFACE ( 'NONE', #80429, 0.1100000000000007222 ) ; +#39527 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#39528 = VECTOR ( 'NONE', #6503, 1000.000000000000114 ) ; +#39529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81975 ) ) ; +#39530 = CARTESIAN_POINT ( 'NONE', ( -1.089947272470209949, -0.8906029366306299488, 0.8299999999999999600 ) ) ; +#39531 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#39532 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39533 = AXIS2_PLACEMENT_3D ( 'NONE', #96029, #4621, #82267 ) ; +#39535 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19940 ) ) ; +#39534 = FILL_AREA_STYLE ('',( #31369 ) ) ; +#39536 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39537 = VECTOR ( 'NONE', #53281, 1000.000000000000000 ) ; +#39538 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852914000000000172, 0.8648700000000000276 ) ) ; +#39539 = ORIENTED_EDGE ( 'NONE', *, *, #31365, .T. ) ; +#39540 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.5000000000000012212, 0.1829999999999659677 ) ) ; +#39541 = ADVANCED_FACE ( 'NONE', ( #38786 ), #69909, .T. ) ; +#39543 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39542 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#39544 = AXIS2_PLACEMENT_3D ( 'NONE', #2223, #32856, #63518 ) ; +#39545 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5329, 'distance_accuracy_value', 'NONE'); +#39546 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39547 = VECTOR ( 'NONE', #94402, 1000.000000000000000 ) ; +#39548 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, 0.000000000000000000 ) ) ; +#39549 = VECTOR ( 'NONE', #7758, 1000.000000000000000 ) ; +#39550 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#39551 = SURFACE_STYLE_FILL_AREA ( #38548 ) ; +#39552 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#39553 = VERTEX_POINT ( 'NONE', #65287 ) ; +#39554 = EDGE_CURVE ( 'NONE', #50096, #94949, #10561, .T. ) ; +#39555 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39556 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39557 = FACE_OUTER_BOUND ( 'NONE', #21288, .T. ) ; +#39558 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#39559 = PRESENTATION_STYLE_ASSIGNMENT (( #64559 ) ) ; +#39560 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39561 = STYLED_ITEM ( 'NONE', ( #42733 ), #66936 ) ; +#39562 = SURFACE_STYLE_USAGE ( .BOTH. , #24785 ) ; +#39563 = ADVANCED_FACE ( 'NONE', ( #79632 ), #42327, .T. ) ; +#39564 = LINE ( 'NONE', #62573, #48 ) ; +#39565 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39566 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 8.003631000000000384, 0.8991599999999999593 ) ) ; +#39567 = FILL_AREA_STYLE ('',( #25292 ) ) ; +#39568 = DIRECTION ( 'NONE', ( 0.7071064476869688420, 0.7071071146859688739, 0.000000000000000000 ) ) ; +#39569 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39570 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#39571 = SURFACE_SIDE_STYLE ('',( #52903 ) ) ; +#39572 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#39573 = VERTEX_POINT ( 'NONE', #79119 ) ; +#39574 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#39575 = EDGE_CURVE ( 'NONE', #22571, #83440, #83309, .T. ) ; +#39576 = ORIENTED_EDGE ( 'NONE', *, *, #21177, .F. ) ; +#39577 = SURFACE_STYLE_FILL_AREA ( #87055 ) ; +#39578 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39579 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#39580 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95010 ) ) ; +#39581 = LINE ( 'NONE', #86552, #74822 ) ; +#39582 = CARTESIAN_POINT ( 'NONE', ( -1.000284964254319897, -1.196758459236680006, 0.8299999999999999600 ) ) ; +#39583 = EDGE_LOOP ( 'NONE', ( #59465, #33490, #72934, #31733, #26037, #32466 ) ) ; +#39584 = CARTESIAN_POINT ( 'NONE', ( -0.05610171574325675120, -0.9010284160966952616, 0.8100000000003940714 ) ) ; +#39585 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39586 = AXIS2_PLACEMENT_3D ( 'NONE', #54547, #1919, #15686 ) ; +#39587 = ORIENTED_EDGE ( 'NONE', *, *, #11561, .T. ) ; +#39588 = SURFACE_STYLE_FILL_AREA ( #8354 ) ; +#39589 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70627 ), #57710 ) ; +#39590 = ADVANCED_FACE ( 'NONE', ( #71446 ), #63802, .T. ) ; +#39591 = EDGE_CURVE ( 'NONE', #54674, #93815, #67284, .T. ) ; +#39592 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980549, 0.000000000000000000 ) ) ; +#39593 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#39594 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30910 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1869, #17655, #41182 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39595 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#39596 = ORIENTED_EDGE ( 'NONE', *, *, #42514, .F. ) ; +#39597 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39598 = ADVANCED_FACE ( 'NONE', ( #97402 ), #59185, .T. ) ; +#39599 = EDGE_CURVE ( 'NONE', #63306, #62639, #50512, .T. ) ; +#39600 = SURFACE_STYLE_FILL_AREA ( #62110 ) ; +#39601 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17639, 'distance_accuracy_value', 'NONE'); +#39602 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33660 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34566, #42698, #28383 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39603 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88510 ) ) ; +#39605 = STYLED_ITEM ( 'NONE', ( #83433 ), #21149 ) ; +#39604 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#39606 = ORIENTED_EDGE ( 'NONE', *, *, #70618, .T. ) ; +#39607 = EDGE_CURVE ( 'NONE', #94573, #21657, #43310, .T. ) ; +#39608 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99757 ), #6857 ) ; +#39609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39610 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671291000000000082, 0.8991599999999999593 ) ) ; +#39611 = ORIENTED_EDGE ( 'NONE', *, *, #70889, .F. ) ; +#39612 = PRESENTATION_STYLE_ASSIGNMENT (( #47266 ) ) ; +#39613 = CARTESIAN_POINT ( 'NONE', ( -0.07152490633971099465, -1.505252428432260148, 0.8299999999999999600 ) ) ; +#39615 = EDGE_CURVE ( 'NONE', #27956, #59324, #4010, .T. ) ; +#39614 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#39616 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39617 = AXIS2_PLACEMENT_3D ( 'NONE', #42979, #82794, #51167 ) ; +#39618 = CARTESIAN_POINT ( 'NONE', ( 0.2546877245216000452, -1.031834659001420018, 0.8299999999999999600 ) ) ; +#39619 = STYLED_ITEM ( 'NONE', ( #9662 ), #59516 ) ; +#39620 = VERTEX_POINT ( 'NONE', #11582 ) ; +#39621 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64368, 'distance_accuracy_value', 'NONE'); +#39622 = VECTOR ( 'NONE', #14210, 1000.000000000000227 ) ; +#39623 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#39625 = FACE_OUTER_BOUND ( 'NONE', #83984, .T. ) ; +#39624 = FACE_OUTER_BOUND ( 'NONE', #13993, .T. ) ; +#39626 = ORIENTED_EDGE ( 'NONE', *, *, #25911, .F. ) ; +#39627 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#39628 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#39629 = FILL_AREA_STYLE ('',( #16610 ) ) ; +#39630 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#39631 = STYLED_ITEM ( 'NONE', ( #28908 ), #67091 ) ; +#39632 = ORIENTED_EDGE ( 'NONE', *, *, #29843, .F. ) ; +#39633 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39634 = ORIENTED_EDGE ( 'NONE', *, *, #72388, .T. ) ; +#39635 = EDGE_LOOP ( 'NONE', ( #96886, #35872, #25003, #44104 ) ) ; +#39636 = CARTESIAN_POINT ( 'NONE', ( 1.363472769114729921, -1.331314275383060020, 0.8299999999999999600 ) ) ; +#39637 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, 3.500000000000000444, 0.000000000000000000 ) ) ; +#39638 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#39640 = EDGE_CURVE ( 'NONE', #72535, #96986, #60187, .T. ) ; +#39639 = LINE ( 'NONE', #38628, #65274 ) ; +#39641 = ORIENTED_EDGE ( 'NONE', *, *, #42284, .F. ) ; +#39642 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#39643 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#39644 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39645 = LINE ( 'NONE', #40169, #96230 ) ; +#39646 = ORIENTED_EDGE ( 'NONE', *, *, #36840, .T. ) ; +#39648 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39647 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#39649 = FILL_AREA_STYLE_COLOUR ( '', #38042 ) ; +#39650 = VERTEX_POINT ( 'NONE', #74476 ) ; +#39651 = ADVANCED_FACE ( 'NONE', ( #5466 ), #44292, .T. ) ; +#39652 = ORIENTED_EDGE ( 'NONE', *, *, #29654, .T. ) ; +#39653 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39654 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39656 = CARTESIAN_POINT ( 'NONE', ( -0.7229898940154579901, 0.6774732877316049784, 0.8100000000000000533 ) ) ; +#39657 = VECTOR ( 'NONE', #41460, 1000.000000000000000 ) ; +#39658 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39659 = VECTOR ( 'NONE', #67556, 1000.000000000000000 ) ; +#39660 = FILL_AREA_STYLE ('',( #71826 ) ) ; +#39661 = FILL_AREA_STYLE_COLOUR ( '', #67816 ) ; +#39662 = ORIENTED_EDGE ( 'NONE', *, *, #70191, .F. ) ; +#39663 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#39664 = ADVANCED_FACE ( 'NONE', ( #15131 ), #37677, .T. ) ; +#39666 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39665 = LINE ( 'NONE', #70293, #27799 ) ; +#39667 = CYLINDRICAL_SURFACE ( 'NONE', #33285, 0.5799999999999999600 ) ; +#39668 = PRESENTATION_STYLE_ASSIGNMENT (( #1379 ) ) ; +#39669 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98335 ) ) ; +#39670 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7500000000000002220, 0.000000000000000000 ) ) ; +#39671 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39672 = LINE ( 'NONE', #29503, #84195 ) ; +#39673 = ORIENTED_EDGE ( 'NONE', *, *, #98361, .T. ) ; +#39674 = EDGE_CURVE ( 'NONE', #99681, #86094, #54515, .T. ) ; +#39675 = LINE ( 'NONE', #48868, #29234 ) ; +#39676 = CYLINDRICAL_SURFACE ( 'NONE', #47230, 0.009999999999999998473 ) ; +#39678 = STYLED_ITEM ( 'NONE', ( #45103 ), #37883 ) ; +#39677 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.4133334038228878016, 0.6665916413350265746 ) ) ; +#39679 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39680 = SURFACE_STYLE_USAGE ( .BOTH. , #78993 ) ; +#39682 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#39681 = VECTOR ( 'NONE', #62667, 1000.000000000000000 ) ; +#39683 = SURFACE_SIDE_STYLE ('',( #41220 ) ) ; +#39684 = LINE ( 'NONE', #57559, #22216 ) ; +#39685 = LINE ( 'NONE', #70828, #40004 ) ; +#39686 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #494 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73006, #17850, #95950 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39687 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39688 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39689 = SURFACE_STYLE_USAGE ( .BOTH. , #63206 ) ; +#39690 = LINE ( 'NONE', #86662, #42268 ) ; +#39691 = VECTOR ( 'NONE', #27990, 1000.000000000000000 ) ; +#39692 = FACE_OUTER_BOUND ( 'NONE', #24264, .T. ) ; +#39693 = EDGE_CURVE ( 'NONE', #75526, #22262, #46807, .T. ) ; +#39694 = STYLED_ITEM ( 'NONE', ( #87036 ), #9355 ) ; +#39695 = CARTESIAN_POINT ( 'NONE', ( 1.880917842042550081, -1.247909878090149860, 0.8100000000000004974 ) ) ; +#39696 = STYLED_ITEM ( 'NONE', ( #59658 ), #11506 ) ; +#39697 = LINE ( 'NONE', #47357, #33884 ) ; +#39699 = EDGE_CURVE ( 'NONE', #21238, #84785, #10130, .T. ) ; +#39698 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#39700 = VERTEX_POINT ( 'NONE', #31001 ) ; +#39701 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#39702 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39703 = VECTOR ( 'NONE', #13917, 1000.000000000000000 ) ; +#39705 = LINE ( 'NONE', #76116, #74724 ) ; +#39704 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#39706 = LINE ( 'NONE', #62214, #87259 ) ; +#39707 = ADVANCED_FACE ( 'NONE', ( #77974 ), #93748, .F. ) ; +#39708 = EDGE_CURVE ( 'NONE', #2585, #37710, #34053, .T. ) ; +#39709 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#39710 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39711 = ORIENTED_EDGE ( 'NONE', *, *, #79626, .F. ) ; +#39712 = LINE ( 'NONE', #84657, #4755 ) ; +#39713 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26696 ), #62552 ) ; +#39714 = FACE_OUTER_BOUND ( 'NONE', #35647, .T. ) ; +#39715 = EDGE_CURVE ( 'NONE', #56583, #44500, #23958, .T. ) ; +#39716 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39717 = EDGE_CURVE ( 'NONE', #6853, #10619, #41200, .T. ) ; +#39718 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, -0.1400000000000000133 ) ) ; +#39719 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39720 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39721 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39722 = SHAPE_REPRESENTATION ( 'Submodel-SOD882_part_SOD882', ( #94097, #53399 ), #98932 ) ; +#39723 = ORIENTED_EDGE ( 'NONE', *, *, #97034, .T. ) ; +#39724 = ORIENTED_EDGE ( 'NONE', *, *, #2277, .F. ) ; +#39725 = EDGE_CURVE ( 'NONE', #77186, #54723, #40701, .T. ) ; +#39726 = STYLED_ITEM ( 'NONE', ( #51240 ), #88305 ) ; +#39727 = VERTEX_POINT ( 'NONE', #40194 ) ; +#39728 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#39729 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2543, #41358, #2043, #88314 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#39730 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#39731 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30896 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21865, #100839, #68312 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39732 = VECTOR ( 'NONE', #37845, 1000.000000000000114 ) ; +#39733 = SURFACE_STYLE_FILL_AREA ( #81082 ) ; +#39734 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696237999999999913, 0.8991599999999999593 ) ) ; +#39735 = EDGE_CURVE ( 'NONE', #91087, #52513, #56026, .T. ) ; +#39736 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #52797 ) ; +#39737 = CARTESIAN_POINT ( 'NONE', ( -1.632862398863140093E-18, 0.8199999999999998401, 0.04999999999999998890 ) ) ; +#39739 = ORIENTED_EDGE ( 'NONE', *, *, #45688, .T. ) ; +#39738 = VERTEX_POINT ( 'NONE', #41703 ) ; +#39740 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56461 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87887, #4615, #96527 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39741 = ORIENTED_EDGE ( 'NONE', *, *, #82513, .F. ) ; +#39742 = FACE_OUTER_BOUND ( 'NONE', #83061, .T. ) ; +#39744 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #588 ), #62589 ) ; +#39743 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55158, 'distance_accuracy_value', 'NONE'); +#39745 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39747 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#39746 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39748 = ORIENTED_EDGE ( 'NONE', *, *, #20359, .F. ) ; +#39749 = VECTOR ( 'NONE', #43692, 1000.000000000000000 ) ; +#39750 = PRESENTATION_STYLE_ASSIGNMENT (( #64742 ) ) ; +#39751 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#39752 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15205 ), #95186 ) ; +#39753 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39754 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#39755 = VERTEX_POINT ( 'NONE', #25887 ) ; +#39757 = FACE_BOUND ( 'NONE', #80750, .T. ) ; +#39756 = PRESENTATION_STYLE_ASSIGNMENT (( #100882 ) ) ; +#39758 = ORIENTED_EDGE ( 'NONE', *, *, #31611, .T. ) ; +#39759 = SURFACE_SIDE_STYLE ('',( #63273 ) ) ; +#39760 = VECTOR ( 'NONE', #29847, 1000.000000000000000 ) ; +#39761 = EDGE_LOOP ( 'NONE', ( #68087, #25702, #2449, #84714, #83838, #49840 ) ) ; +#39762 = ORIENTED_EDGE ( 'NONE', *, *, #84849, .T. ) ; +#39763 = VECTOR ( 'NONE', #13397, 1000.000000000000114 ) ; +#39764 = FACE_OUTER_BOUND ( 'NONE', #54294, .T. ) ; +#39765 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39766 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#39768 = ORIENTED_EDGE ( 'NONE', *, *, #5887, .T. ) ; +#39767 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39769 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39770 = SURFACE_STYLE_USAGE ( .BOTH. , #6541 ) ; +#39771 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.699999999999999956, 0.1829999999999919746 ) ) ; +#39772 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88573 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11925, #4836, #67132 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39773 = SURFACE_STYLE_USAGE ( .BOTH. , #48464 ) ; +#39774 = VERTEX_POINT ( 'NONE', #88647 ) ; +#39775 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.67582000000000164, 0.8648700000000000276 ) ) ; +#39776 = SURFACE_STYLE_USAGE ( .BOTH. , #46903 ) ; +#39777 = EDGE_LOOP ( 'NONE', ( #32740, #12083, #80767, #48867, #91467, #179 ) ) ; +#39778 = EDGE_CURVE ( 'NONE', #10654, #89973, #91763, .T. ) ; +#39779 = EDGE_LOOP ( 'NONE', ( #10095, #8638, #35114, #19675, #51506, #47721 ) ) ; +#39780 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#39781 = LINE ( 'NONE', #55629, #18843 ) ; +#39782 = CIRCLE ( 'NONE', #74116, 0.04999999999999999584 ) ; +#39783 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39784 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.41999999999999993 ) ) ; +#39785 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#39786 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#39787 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95168, 'distance_accuracy_value', 'NONE'); +#39788 = ORIENTED_EDGE ( 'NONE', *, *, #6077, .F. ) ; +#39789 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39790 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#39791 = VERTEX_POINT ( 'NONE', #78474 ) ; +#39792 = STYLED_ITEM ( 'NONE', ( #34796 ), #71208 ) ; +#39793 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8991599999999999593 ) ) ; +#39794 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39795 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39797 = FACE_OUTER_BOUND ( 'NONE', #27843, .T. ) ; +#39796 = LINE ( 'NONE', #55149, #96850 ) ; +#39798 = CARTESIAN_POINT ( 'NONE', ( 1.753807303740889889, -0.9763607356531520676, 0.8299999999999999600 ) ) ; +#39799 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.000000000000000000 ) ) ; +#39800 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39801 = SURFACE_STYLE_FILL_AREA ( #8557 ) ; +#39802 = EDGE_CURVE ( 'NONE', #22291, #13814, #57047, .T. ) ; +#39803 = FILL_AREA_STYLE ('',( #57168 ) ) ; +#39804 = PLANE ( 'NONE', #38997 ) ; +#39805 = VECTOR ( 'NONE', #92393, 1000.000000000000000 ) ; +#39806 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72440 ), #56153 ) ; +#39807 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.000000000000000000 ) ) ; +#39808 = LINE ( 'NONE', #95912, #30411 ) ; +#39809 = CARTESIAN_POINT ( 'NONE', ( 9.408391499500050159, 2.983172500499951862, 0.8991599999999999593 ) ) ; +#39810 = STYLED_ITEM ( 'NONE', ( #71617 ), #47804 ) ; +#39811 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#39812 = SURFACE_STYLE_FILL_AREA ( #87783 ) ; +#39813 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83842 ) ) ; +#39814 = PLANE ( 'NONE', #40594 ) ; +#39815 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #7379 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#39816 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39817 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#39818 = VECTOR ( 'NONE', #16901, 1000.000000000000000 ) ; +#39819 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12034 ), #7065 ) ; +#39820 = ORIENTED_EDGE ( 'NONE', *, *, #84348, .F. ) ; +#39821 = FILL_AREA_STYLE_COLOUR ( '', #3622 ) ; +#39822 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.399999999999999911, -11.91999999999999993 ) ) ; +#39823 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99727, 'distance_accuracy_value', 'NONE'); +#39824 = ORIENTED_EDGE ( 'NONE', *, *, #99837, .F. ) ; +#39826 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53877, 'distance_accuracy_value', 'NONE'); +#39825 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6761799387799151129, 0.000000000000000000 ) ) ; +#39827 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39828 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39830 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33357 ) ) ; +#39829 = VECTOR ( 'NONE', #49067, 1000.000000000000000 ) ; +#39831 = LINE ( 'NONE', #85768, #50397 ) ; +#39832 = VECTOR ( 'NONE', #64797, 1000.000000000000000 ) ; +#39833 = PRESENTATION_STYLE_ASSIGNMENT (( #16303 ) ) ; +#39834 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39835 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18549, #8791, #55876, #72688 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#39836 = VECTOR ( 'NONE', #15967, 1000.000000000000000 ) ; +#39837 = EDGE_LOOP ( 'NONE', ( #27959, #43576, #63019, #41797 ) ) ; +#39838 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39839 = ORIENTED_EDGE ( 'NONE', *, *, #67396, .F. ) ; +#39840 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#39841 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16159, 'distance_accuracy_value', 'NONE'); +#39842 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#39843 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39844 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39845 = EDGE_CURVE ( 'NONE', #97591, #85285, #9460, .T. ) ; +#39846 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39847 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39848 = AXIS2_PLACEMENT_3D ( 'NONE', #38737, #47406, #6026 ) ; +#39849 = ORIENTED_EDGE ( 'NONE', *, *, #87630, .F. ) ; +#39850 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39851 = VERTEX_POINT ( 'NONE', #8431 ) ; +#39852 = LINE ( 'NONE', #55701, #11451 ) ; +#39853 = VERTEX_POINT ( 'NONE', #55531 ) ; +#39854 = CARTESIAN_POINT ( 'NONE', ( 1.036940038338219905, -1.318596846191909977, 0.8100000000000000533 ) ) ; +#39855 = FILL_AREA_STYLE_COLOUR ( '', #49892 ) ; +#39856 = FILL_AREA_STYLE_COLOUR ( '', #83809 ) ; +#39857 = ADVANCED_FACE ( 'NONE', ( #1887 ), #26388, .T. ) ; +#39858 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39859 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#39862 = VERTEX_POINT ( 'NONE', #94268 ) ; +#39861 = VERTEX_POINT ( 'NONE', #87150 ) ; +#39860 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98445 ) ) ; +#39863 = SURFACE_STYLE_FILL_AREA ( #24591 ) ; +#39864 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#39865 = EDGE_LOOP ( 'NONE', ( #75952, #94092, #5064, #78314 ) ) ; +#39866 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39867 = STYLED_ITEM ( 'NONE', ( #70442 ), #89363 ) ; +#39868 = STYLED_ITEM ( 'NONE', ( #86885 ), #53706 ) ; +#39870 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.076179938779915135, 0.000000000000000000 ) ) ; +#39869 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#39871 = ORIENTED_EDGE ( 'NONE', *, *, #15353, .F. ) ; +#39872 = EDGE_LOOP ( 'NONE', ( #23014, #21677, #10783, #45874, #4042, #27969 ) ) ; +#39873 = CONICAL_SURFACE ( 'NONE', #35024, 0.6999999998811290425, 0.7853981639658824676 ) ; +#39874 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37976 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24901, #95782, #17683 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39875 = FILL_AREA_STYLE_COLOUR ( '', #43106 ) ; +#39876 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39877 = ORIENTED_EDGE ( 'NONE', *, *, #53408, .F. ) ; +#39878 = ORIENTED_EDGE ( 'NONE', *, *, #88298, .T. ) ; +#39879 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#39880 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85561 ) ) ; +#39881 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#39882 = ORIENTED_EDGE ( 'NONE', *, *, #60018, .T. ) ; +#39883 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #98938, #21417, #83220, #53082 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#39884 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959499, 1.048695503451053346E-76 ) ) ; +#39885 = EDGE_CURVE ( 'NONE', #89489, #12539, #1174, .T. ) ; +#39886 = AXIS2_PLACEMENT_3D ( 'NONE', #9826, #88026, #33419 ) ; +#39888 = ORIENTED_EDGE ( 'NONE', *, *, #34386, .T. ) ; +#39887 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#39889 = SURFACE_SIDE_STYLE ('',( #55732 ) ) ; +#39890 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31379 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55645, #46415, #40317 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39891 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44737 ), #35037 ) ; +#39892 = LINE ( 'NONE', #77679, #23722 ) ; +#39893 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#39894 = ORIENTED_EDGE ( 'NONE', *, *, #89470, .F. ) ; +#39895 = LINE ( 'NONE', #56760, #28887 ) ; +#39896 = ORIENTED_EDGE ( 'NONE', *, *, #68725, .F. ) ; +#39897 = EDGE_CURVE ( 'NONE', #52058, #99428, #10430, .T. ) ; +#39899 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72204 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24497, #32129, #78082 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#39898 = STYLED_ITEM ( 'NONE', ( #55984 ), #38222 ) ; +#39900 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.05000000000000000971, 0.2100000000000000200 ) ) ; +#39901 = AXIS2_PLACEMENT_3D ( 'NONE', #34573, #20208, #49363 ) ; +#39902 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39903 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.7000000000000018430, 7.851278178449085673E-79 ) ) ; +#39905 = ORIENTED_EDGE ( 'NONE', *, *, #398, .F. ) ; +#39904 = SURFACE_SIDE_STYLE ('',( #37892 ) ) ; +#39906 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28469 ) ) ; +#39907 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999989875, 0.000000000000000000 ) ) ; +#39908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39910 = CARTESIAN_POINT ( 'NONE', ( 1.536752279304230084, -1.444662699359980040, 0.8299999999999999600 ) ) ; +#39909 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#39911 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999922691396, 0.1200000000000000094, -0.3250000000000000666 ) ) ; +#39912 = CARTESIAN_POINT ( 'NONE', ( 1.624720795854639910, -0.9850088450568520448, 0.8299999999999990719 ) ) ; +#39913 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#39914 = CARTESIAN_POINT ( 'NONE', ( 1.795983389471520253, -1.255590633215009966, 0.8099999999999996092 ) ) ; +#39915 = EDGE_LOOP ( 'NONE', ( #18523, #70662, #48146, #97217 ) ) ; +#39916 = SURFACE_SIDE_STYLE ('',( #95511 ) ) ; +#39917 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, -0.2400000000000000189 ) ) ; +#39918 = FACE_OUTER_BOUND ( 'NONE', #90942, .T. ) ; +#39919 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7578679656440356904, 0.2000000000000000111 ) ) ; +#39920 = CARTESIAN_POINT ( 'NONE', ( 1.566818635346699962, -1.328064047174219997, 0.8299999999999999600 ) ) ; +#39921 = FILL_AREA_STYLE ('',( #16387 ) ) ; +#39922 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39923 = EDGE_CURVE ( 'NONE', #96771, #63380, #60056, .T. ) ; +#39924 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.500000000000000000, 9.346759736271676912E-79 ) ) ; +#39925 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#39926 = VERTEX_POINT ( 'NONE', #43676 ) ; +#39927 = VECTOR ( 'NONE', #4230, 1000.000000000000000 ) ; +#39928 = EDGE_CURVE ( 'NONE', #34794, #81337, #40346, .T. ) ; +#39929 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39930 = VERTEX_POINT ( 'NONE', #59060 ) ; +#39931 = CIRCLE ( 'NONE', #96971, 0.3000000000000000444 ) ; +#39933 = PRESENTATION_STYLE_ASSIGNMENT (( #14383 ) ) ; +#39932 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39934 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39935 = PRESENTATION_STYLE_ASSIGNMENT (( #95026 ) ) ; +#39936 = VERTEX_POINT ( 'NONE', #36558 ) ; +#39937 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 2.100000000000000089, 0.1829999999999959992 ) ) ; +#39938 = EDGE_CURVE ( 'NONE', #34606, #3163, #19711, .T. ) ; +#39939 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01085786437626898131, -0.1500000000000000222 ) ) ; +#39940 = EDGE_CURVE ( 'NONE', #37746, #92463, #74837, .T. ) ; +#39941 = LINE ( 'NONE', #31263, #13859 ) ; +#39942 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#39943 = VECTOR ( 'NONE', #52085, 1000.000000000000000 ) ; +#39944 = LINE ( 'NONE', #15926, #24212 ) ; +#39945 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39946 = PRESENTATION_STYLE_ASSIGNMENT (( #4766 ) ) ; +#39947 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#39949 = SURFACE_STYLE_FILL_AREA ( #8703 ) ; +#39948 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36896 ), #10706 ) ; +#39950 = FILL_AREA_STYLE ('',( #37936 ) ) ; +#39951 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44798 ) ) ; +#39952 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46475 ), #5716 ) ; +#39953 = CARTESIAN_POINT ( 'NONE', ( 0.06710731395959769474, -1.024811280222130083, 0.8100000000000000533 ) ) ; +#39954 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39008, 'distance_accuracy_value', 'NONE'); +#39955 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39956 = ORIENTED_EDGE ( 'NONE', *, *, #34551, .F. ) ; +#39957 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.1200000000000003147, 0.2999999999999999889 ) ) ; +#39958 = EDGE_LOOP ( 'NONE', ( #64632, #92227, #79094, #2063 ) ) ; +#39959 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#39960 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62578, 'distance_accuracy_value', 'NONE'); +#39961 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13809, 'distance_accuracy_value', 'NONE'); +#39962 = LINE ( 'NONE', #58338, #16170 ) ; +#39963 = SURFACE_SIDE_STYLE ('',( #1144 ) ) ; +#39964 = EDGE_CURVE ( 'NONE', #44986, #58513, #51378, .T. ) ; +#39965 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#39966 = VECTOR ( 'NONE', #36943, 1000.000000000000000 ) ; +#39967 = CARTESIAN_POINT ( 'NONE', ( 0.07744069998345409767, -1.407232784796780045, 0.8300000000000004041 ) ) ; +#39968 = SURFACE_STYLE_USAGE ( .BOTH. , #38459 ) ; +#39969 = VECTOR ( 'NONE', #58211, 1000.000000000000000 ) ; +#39970 = ORIENTED_EDGE ( 'NONE', *, *, #38983, .T. ) ; +#39971 = PLANE ( 'NONE', #31316 ) ; +#39972 = PLANE ( 'NONE', #75960 ) ; +#39973 = SURFACE_SIDE_STYLE ('',( #64468 ) ) ; +#39974 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4617, 'distance_accuracy_value', 'NONE'); +#39976 = VECTOR ( 'NONE', #29482, 1000.000000000000000 ) ; +#39975 = AXIS2_PLACEMENT_3D ( 'NONE', #19541, #43516, #96117 ) ; +#39977 = EDGE_LOOP ( 'NONE', ( #49509, #60716, #74207, #36248 ) ) ; +#39978 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#39979 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64396 ), #53028 ) ; +#39980 = EDGE_LOOP ( 'NONE', ( #39512, #47903, #51841, #2609 ) ) ; +#39981 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#39982 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#39983 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#39984 = DIRECTION ( 'NONE', ( 0.7071067811865472397, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#39985 = ORIENTED_EDGE ( 'NONE', *, *, #367, .T. ) ; +#39986 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #835 ) ) ; +#39987 = FACE_OUTER_BOUND ( 'NONE', #79454, .T. ) ; +#39988 = STYLED_ITEM ( 'NONE', ( #14933 ), #12593 ) ; +#39989 = CARTESIAN_POINT ( 'NONE', ( -0.7666666666666723806, 3.500000000000000000, 0.000000000000000000 ) ) ; +#39990 = PLANE ( 'NONE', #89808 ) ; +#39991 = VERTEX_POINT ( 'NONE', #4870 ) ; +#39992 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#39993 = STYLED_ITEM ( 'NONE', ( #90985 ), #68385 ) ; +#39994 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#39995 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.6899999999999999467, 0.2077922077922079724 ) ) ; +#39996 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#39997 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#39998 = VERTEX_POINT ( 'NONE', #89160 ) ; +#40000 = EDGE_LOOP ( 'NONE', ( #9529, #89947, #24653, #88369, #41291, #15343 ) ) ; +#39999 = STYLED_ITEM ( 'NONE', ( #81747 ), #72888 ) ; +#40001 = VERTEX_POINT ( 'NONE', #82517 ) ; +#40002 = CARTESIAN_POINT ( 'NONE', ( 1.810920360744870061, -1.177156496261070107, 0.8299999999999995159 ) ) ; +#40003 = EDGE_CURVE ( 'NONE', #37342, #10112, #57346, .T. ) ; +#40004 = VECTOR ( 'NONE', #883, 1000.000000000000000 ) ; +#40005 = VECTOR ( 'NONE', #37869, 1000.000000000000000 ) ; +#40006 = ORIENTED_EDGE ( 'NONE', *, *, #42842, .F. ) ; +#40008 = ORIENTED_EDGE ( 'NONE', *, *, #68067, .T. ) ; +#40007 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8199999999999999512 ) ) ; +#40009 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40010 = VECTOR ( 'NONE', #18471, 1000.000000000000000 ) ; +#40012 = LINE ( 'NONE', #8768, #62822 ) ; +#40011 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40013 = FILL_AREA_STYLE_COLOUR ( '', #83990 ) ; +#40014 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597380222, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#40015 = VERTEX_POINT ( 'NONE', #91162 ) ; +#40016 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#40017 = CARTESIAN_POINT ( 'NONE', ( 1.823289888948260273, -1.336414498567920273, 0.8099999999999997202 ) ) ; +#40018 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40019 = ORIENTED_EDGE ( 'NONE', *, *, #13306, .F. ) ; +#40020 = ADVANCED_FACE ( 'NONE', ( #67168 ), #82018, .T. ) ; +#40021 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69562 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54957, #86580, #79441 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40022 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26994 ), #98667 ) ; +#40024 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40025 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.463023860841316052E-78, -1.991364888915569965E-47 ) ) ; +#40026 = ORIENTED_EDGE ( 'NONE', *, *, #91309, .T. ) ; +#40027 = ADVANCED_FACE ( 'NONE', ( #98734 ), #11453, .T. ) ; +#40029 = FILL_AREA_STYLE_COLOUR ( '', #69768 ) ; +#40028 = VECTOR ( 'NONE', #68110, 1000.000000000000000 ) ; +#40030 = VECTOR ( 'NONE', #51430, 1000.000000000000000 ) ; +#40031 = ORIENTED_EDGE ( 'NONE', *, *, #45047, .T. ) ; +#40032 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40033 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40034 = FILL_AREA_STYLE ('',( #41549 ) ) ; +#40035 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93762 ), #92190 ) ; +#40036 = PRESENTATION_STYLE_ASSIGNMENT (( #94106 ) ) ; +#40037 = VERTEX_POINT ( 'NONE', #93121 ) ; +#40038 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14491 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46326, #63224, #70856 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40039 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#40041 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3952 ) ) ; +#40040 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88956 ), #38436 ) ; +#40042 = AXIS2_PLACEMENT_3D ( 'NONE', #43567, #36931, #90036 ) ; +#40043 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3157, 'distance_accuracy_value', 'NONE'); +#40044 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40045 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.723820061220085131, 0.000000000000000000 ) ) ; +#40046 = EDGE_CURVE ( 'NONE', #3674, #76885, #45446, .T. ) ; +#40047 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84072 ) ) ; +#40048 = EDGE_CURVE ( 'NONE', #28686, #6853, #84008, .T. ) ; +#40049 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40050 = LINE ( 'NONE', #63043, #93473 ) ; +#40051 = FACE_OUTER_BOUND ( 'NONE', #56535, .T. ) ; +#40052 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40053 = ORIENTED_EDGE ( 'NONE', *, *, #568, .F. ) ; +#40054 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40057 = SURFACE_SIDE_STYLE ('',( #94132 ) ) ; +#40056 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40055 = SURFACE_STYLE_USAGE ( .BOTH. , #1238 ) ; +#40058 = LINE ( 'NONE', #56421, #86285 ) ; +#40059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17182 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19024, #56382, #66506 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40060 = CARTESIAN_POINT ( 'NONE', ( -0.1192017212701950019, -1.445336647901249938, 0.8100000000000000533 ) ) ; +#40061 = SURFACE_SIDE_STYLE ('',( #86522 ) ) ; +#40062 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40063 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#40064 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40065 = PRESENTATION_STYLE_ASSIGNMENT (( #57414 ) ) ; +#40066 = ORIENTED_EDGE ( 'NONE', *, *, #92020, .T. ) ; +#40067 = SURFACE_SIDE_STYLE ('',( #79892 ) ) ; +#40068 = EDGE_CURVE ( 'NONE', #12058, #84465, #68155, .T. ) ; +#40069 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40070 = EDGE_CURVE ( 'NONE', #38179, #26486, #76839, .T. ) ; +#40071 = SURFACE_SIDE_STYLE ('',( #8826 ) ) ; +#40072 = SURFACE_SIDE_STYLE ('',( #8828 ) ) ; +#40073 = PRESENTATION_STYLE_ASSIGNMENT (( #16045 ) ) ; +#40074 = LINE ( 'NONE', #93132, #57946 ) ; +#40075 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40076 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95427 ), #53127 ) ; +#40077 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40079 = PRESENTATION_STYLE_ASSIGNMENT (( #9846 ) ) ; +#40080 = PRESENTATION_STYLE_ASSIGNMENT (( #94161 ) ) ; +#40081 = FILL_AREA_STYLE ('',( #24283 ) ) ; +#40082 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31829 ), #82438 ) ; +#40083 = LINE ( 'NONE', #47735, #84617 ) ; +#40084 = ORIENTED_EDGE ( 'NONE', *, *, #51464, .F. ) ; +#40085 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#40086 = ORIENTED_EDGE ( 'NONE', *, *, #56348, .T. ) ; +#40087 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78753, 'distance_accuracy_value', 'NONE'); +#40088 = FILL_AREA_STYLE ('',( #94676 ) ) ; +#40089 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#40090 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#40091 = ADVANCED_FACE ( 'NONE', ( #52874 ), #23238, .T. ) ; +#40092 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40093 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51880, #21216, #52382, #1250 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40094 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87719 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91526, #69528, #45516 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40095 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40096 = LINE ( 'NONE', #70200, #89555 ) ; +#40097 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#40098 = EDGE_LOOP ( 'NONE', ( #37738, #80104, #93724, #24538 ) ) ; +#40099 = CARTESIAN_POINT ( 'NONE', ( 0.06950833730751354578, -1.036433488014469217, 0.8100000000001918998 ) ) ; +#40100 = AXIS2_PLACEMENT_3D ( 'NONE', #32349, #79313, #71142 ) ; +#40101 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40102 = EDGE_CURVE ( 'NONE', #80230, #1862, #30511, .T. ) ; +#40103 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22454, 'distance_accuracy_value', 'NONE'); +#40104 = VECTOR ( 'NONE', #72796, 1000.000000000000000 ) ; +#40106 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40105 = VECTOR ( 'NONE', #75004, 1000.000000000000114 ) ; +#40107 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, 1.048695503451022204E-76 ) ) ; +#40108 = AXIS2_PLACEMENT_3D ( 'NONE', #94370, #54084, #100412 ) ; +#40109 = ORIENTED_EDGE ( 'NONE', *, *, #22690, .T. ) ; +#40110 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #48729, #2756, #50754, #79867 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40111 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40112 = EDGE_CURVE ( 'NONE', #32855, #56849, #45162, .T. ) ; +#40113 = AXIS2_PLACEMENT_3D ( 'NONE', #68843, #30057, #85697 ) ; +#40114 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#40116 = EDGE_CURVE ( 'NONE', #57616, #7985, #1760, .T. ) ; +#40115 = LINE ( 'NONE', #23278, #1740 ) ; +#40117 = SURFACE_STYLE_USAGE ( .BOTH. , #100742 ) ; +#40118 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25474 ), #49971 ) ; +#40119 = ORIENTED_EDGE ( 'NONE', *, *, #73067, .T. ) ; +#40120 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40121 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76295, 'distance_accuracy_value', 'NONE'); +#40122 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93838 ) ) ; +#40123 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#40124 = ORIENTED_EDGE ( 'NONE', *, *, #35669, .F. ) ; +#40125 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40126 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40127 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40128 = VERTEX_POINT ( 'NONE', #16041 ) ; +#40129 = LINE ( 'NONE', #70233, #42826 ) ; +#40130 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000985, -0.1400000000000000133 ) ) ; +#40131 = SURFACE_STYLE_FILL_AREA ( #9885 ) ; +#40132 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#40133 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52546 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81756, #83246, #28602 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40134 = VECTOR ( 'NONE', #12167, 1000.000000000000000 ) ; +#40135 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #20873, #5172 ) ; +#40136 = EDGE_CURVE ( 'NONE', #80304, #44974, #44388, .T. ) ; +#40137 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40710 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68499, #23072, #60880 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40138 = VERTEX_POINT ( 'NONE', #32906 ) ; +#40140 = ORIENTED_EDGE ( 'NONE', *, *, #76271, .T. ) ; +#40139 = SURFACE_STYLE_USAGE ( .BOTH. , #93191 ) ; +#40141 = STYLED_ITEM ( 'NONE', ( #62123 ), #12986 ) ; +#40142 = DIRECTION ( 'NONE', ( 9.346570452461240360E-17, -1.000000000000000000, 5.551115123125790098E-17 ) ) ; +#40143 = LINE ( 'NONE', #85066, #31815 ) ; +#40144 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40145 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#40146 = ORIENTED_EDGE ( 'NONE', *, *, #26328, .T. ) ; +#40147 = ADVANCED_FACE ( 'NONE', ( #48746 ), #71707, .T. ) ; +#40148 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40149 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40150 = SURFACE_SIDE_STYLE ('',( #10914 ) ) ; +#40151 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#40152 = ORIENTED_EDGE ( 'NONE', *, *, #73328, .T. ) ; +#40153 = ADVANCED_FACE ( 'NONE', ( #64551 ), #74102, .T. ) ; +#40154 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92305 ) ) ; +#40156 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40155 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#40157 = ORIENTED_EDGE ( 'NONE', *, *, #9437, .T. ) ; +#40158 = ORIENTED_EDGE ( 'NONE', *, *, #20341, .T. ) ; +#40159 = PRESENTATION_STYLE_ASSIGNMENT (( #47289 ) ) ; +#40160 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40161 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28699 ) ) ; +#40163 = ADVANCED_FACE ( 'NONE', ( #93623 ), #23741, .F. ) ; +#40162 = PRESENTATION_STYLE_ASSIGNMENT (( #63655 ) ) ; +#40164 = ORIENTED_EDGE ( 'NONE', *, *, #94957, .T. ) ; +#40165 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40166 = SURFACE_SIDE_STYLE ('',( #78444 ) ) ; +#40167 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79222 ), #43430 ) ; +#40168 = STYLED_ITEM ( 'NONE', ( #10313 ), #90544 ) ; +#40169 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#40170 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44736 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75108, #61802, #76091 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40171 = VERTEX_POINT ( 'NONE', #36799 ) ; +#40172 = FILL_AREA_STYLE ('',( #39649 ) ) ; +#40173 = VERTEX_POINT ( 'NONE', #28146 ) ; +#40174 = ORIENTED_EDGE ( 'NONE', *, *, #86233, .F. ) ; +#40175 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40176 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40177 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22907 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93580, #54858, #100652 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40178 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, -3.500000000000000444, 0.000000000000000000 ) ) ; +#40179 = DIRECTION ( 'NONE', ( 0.9408821649279537347, 0.000000000000000000, -0.3387340427540269649 ) ) ; +#40180 = AXIS2_PLACEMENT_3D ( 'NONE', #63658, #64640, #1347 ) ; +#40181 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8100000000000000533 ) ) ; +#40182 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #90596 ) ; +#40183 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40184 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#40185 = EDGE_LOOP ( 'NONE', ( #63152, #3854, #76144, #87723 ) ) ; +#40186 = AXIS2_PLACEMENT_3D ( 'NONE', #95728, #23819, #1846 ) ; +#40187 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82602 ), #20628 ) ; +#40189 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#40188 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40190 = FACE_OUTER_BOUND ( 'NONE', #14815, .T. ) ; +#40191 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40192 = STYLED_ITEM ( 'NONE', ( #51559 ), #15830 ) ; +#40193 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8648700000000000276 ) ) ; +#40194 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8648700000000000276 ) ) ; +#40195 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#40196 = SURFACE_STYLE_FILL_AREA ( #16652 ) ; +#40197 = FILL_AREA_STYLE ('',( #22858 ) ) ; +#40198 = ORIENTED_EDGE ( 'NONE', *, *, #66229, .T. ) ; +#40199 = LINE ( 'NONE', #55022, #57045 ) ; +#40200 = VECTOR ( 'NONE', #53960, 1000.000000000000000 ) ; +#40201 = PLANE ( 'NONE', #470 ) ; +#40202 = SURFACE_SIDE_STYLE ('',( #78989 ) ) ; +#40203 = EDGE_CURVE ( 'NONE', #13392, #61851, #37318, .T. ) ; +#40204 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100397 ), #56549 ) ; +#40205 = FILL_AREA_STYLE_COLOUR ( '', #51336 ) ; +#40206 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40207 = PLANE ( 'NONE', #12520 ) ; +#40208 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.300000000000000044, -0.02000000000000000042 ) ) ; +#40209 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75033, 'distance_accuracy_value', 'NONE'); +#40210 = FILL_AREA_STYLE ('',( #48392 ) ) ; +#40211 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40212 = DIRECTION ( 'NONE', ( 0.7071067811865485719, -0.7071067811865465735, 0.000000000000000000 ) ) ; +#40213 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40214 = SURFACE_STYLE_USAGE ( .BOTH. , #8963 ) ; +#40215 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40216 = PLANE ( 'NONE', #99221 ) ; +#40217 = CYLINDRICAL_SURFACE ( 'NONE', #51918, 0.1000000000000000472 ) ; +#40219 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#40218 = STYLED_ITEM ( 'NONE', ( #71138 ), #13293 ) ; +#40220 = FILL_AREA_STYLE ('',( #16181 ) ) ; +#40221 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000001332, -0.2400000000000000189 ) ) ; +#40222 = ORIENTED_EDGE ( 'NONE', *, *, #20751, .F. ) ; +#40223 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#40224 = LINE ( 'NONE', #87176, #1384 ) ; +#40225 = FILL_AREA_STYLE_COLOUR ( '', #73027 ) ; +#40226 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40227 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42307, 'distance_accuracy_value', 'NONE'); +#40229 = PLANE ( 'NONE', #25835 ) ; +#40228 = CARTESIAN_POINT ( 'NONE', ( -0.09657079632682520620, -1.219829592979950084, 0.8300000000000002931 ) ) ; +#40230 = CARTESIAN_POINT ( 'NONE', ( 1.186288673455138110, -1.445067339141033136, 0.8099999999997098410 ) ) ; +#40231 = CARTESIAN_POINT ( 'NONE', ( 1.251378114009749964, -1.164076084035881697, 0.8099999999998868105 ) ) ; +#40232 = EDGE_LOOP ( 'NONE', ( #32239, #26541, #46811, #82690 ) ) ; +#40233 = EDGE_CURVE ( 'NONE', #62388, #32073, #59821, .T. ) ; +#40234 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40235 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#40236 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24172, 'distance_accuracy_value', 'NONE'); +#40238 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40237 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40239 = STYLED_ITEM ( 'NONE', ( #54645 ), #90653 ) ; +#40240 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36539, 'distance_accuracy_value', 'NONE'); +#40241 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40242 = ORIENTED_EDGE ( 'NONE', *, *, #50806, .T. ) ; +#40244 = EDGE_LOOP ( 'NONE', ( #34125, #8618, #10028, #48244 ) ) ; +#40243 = STYLED_ITEM ( 'NONE', ( #54087 ), #83226 ) ; +#40245 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#40246 = ORIENTED_EDGE ( 'NONE', *, *, #96532, .T. ) ; +#40247 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#40248 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1090 ) ) ; +#40249 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40250 = LINE ( 'NONE', #87707, #66338 ) ; +#40251 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.500000000000000222, 0.1829999999999870064 ) ) ; +#40252 = SURFACE_SIDE_STYLE ('',( #16713 ) ) ; +#40253 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40254 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #9012 ) ; +#40255 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40258 = ORIENTED_EDGE ( 'NONE', *, *, #27592, .F. ) ; +#40257 = ORIENTED_EDGE ( 'NONE', *, *, #92573, .F. ) ; +#40256 = EDGE_CURVE ( 'NONE', #52467, #97804, #28628, .T. ) ; +#40259 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40260 = ORIENTED_EDGE ( 'NONE', *, *, #74651, .T. ) ; +#40261 = ORIENTED_EDGE ( 'NONE', *, *, #30651, .F. ) ; +#40262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92402 ) ) ; +#40264 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#40266 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40265 = CARTESIAN_POINT ( 'NONE', ( 0.4915531961084259605, -0.9443244458491719673, 0.8299999999999999600 ) ) ; +#40267 = ORIENTED_EDGE ( 'NONE', *, *, #28234, .F. ) ; +#40268 = EDGE_CURVE ( 'NONE', #9645, #75965, #90926, .T. ) ; +#40270 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#40269 = SURFACE_SIDE_STYLE ('',( #79067 ) ) ; +#40271 = DIRECTION ( 'NONE', ( 0.9317134237021232890, 0.000000000000000000, 0.3631942952377801292 ) ) ; +#40272 = VECTOR ( 'NONE', #97201, 1000.000000000000000 ) ; +#40273 = PRESENTATION_STYLE_ASSIGNMENT (( #14201 ) ) ; +#40274 = EDGE_LOOP ( 'NONE', ( #85166, #29840, #68965, #35256 ) ) ; +#40275 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#40276 = ORIENTED_EDGE ( 'NONE', *, *, #87500, .F. ) ; +#40278 = SURFACE_SIDE_STYLE ('',( #40779 ) ) ; +#40277 = FACE_OUTER_BOUND ( 'NONE', #68825, .T. ) ; +#40279 = VECTOR ( 'NONE', #33335, 1000.000000000000000 ) ; +#40280 = ORIENTED_EDGE ( 'NONE', *, *, #85474, .F. ) ; +#40281 = VERTEX_POINT ( 'NONE', #43946 ) ; +#40282 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.549999999999999822, 0.000000000000000000 ) ) ; +#40283 = VECTOR ( 'NONE', #67987, 1000.000000000000227 ) ; +#40284 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#40285 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#40287 = EDGE_CURVE ( 'NONE', #29809, #73427, #51131, .T. ) ; +#40286 = SURFACE_STYLE_FILL_AREA ( #54608 ) ; +#40288 = EDGE_LOOP ( 'NONE', ( #67838, #63645, #98927, #95939, #86843, #42403 ) ) ; +#40289 = VECTOR ( 'NONE', #27722, 1000.000000000000000 ) ; +#40290 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40291 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#40292 = ORIENTED_EDGE ( 'NONE', *, *, #95836, .F. ) ; +#40294 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40293 = FILL_AREA_STYLE ('',( #63289 ) ) ; +#40295 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#40296 = ORIENTED_EDGE ( 'NONE', *, *, #534, .F. ) ; +#40297 = EDGE_CURVE ( 'NONE', #15191, #25700, #19963, .T. ) ; +#40298 = EDGE_LOOP ( 'NONE', ( #58089, #50469 ) ) ; +#40300 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#40299 = FILL_AREA_STYLE_COLOUR ( '', #24682 ) ; +#40301 = FILL_AREA_STYLE_COLOUR ( '', #31904 ) ; +#40302 = SURFACE_STYLE_FILL_AREA ( #94870 ) ; +#40303 = AXIS2_PLACEMENT_3D ( 'NONE', #75026, #43859, #13137 ) ; +#40304 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28904 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72952, #18806, #51513 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40305 = FACE_OUTER_BOUND ( 'NONE', #68907, .T. ) ; +#40306 = ADVANCED_FACE ( 'NONE', ( #84265 ), #91907, .F. ) ; +#40308 = EDGE_CURVE ( 'NONE', #93204, #65363, #12738, .T. ) ; +#40307 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40309 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#40310 = VERTEX_POINT ( 'NONE', #31640 ) ; +#40311 = CARTESIAN_POINT ( 'NONE', ( 0.3213506759258810130, -1.250167574961789985, 0.8299999999999999600 ) ) ; +#40312 = ORIENTED_EDGE ( 'NONE', *, *, #25577, .F. ) ; +#40313 = EDGE_CURVE ( 'NONE', #76676, #53312, #62819, .T. ) ; +#40314 = EDGE_CURVE ( 'NONE', #44243, #91965, #30116, .T. ) ; +#40315 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #70251, #31466, #62636, #13550 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40316 = SURFACE_STYLE_FILL_AREA ( #63800 ) ; +#40317 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40318 = VECTOR ( 'NONE', #17684, 1000.000000000000000 ) ; +#40320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40319 = PLANE ( 'NONE', #74075 ) ; +#40321 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40322 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40323 = FILL_AREA_STYLE ('',( #16781 ) ) ; +#40324 = EDGE_CURVE ( 'NONE', #49127, #6547, #24014, .T. ) ; +#40325 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#40326 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89221 ) ) ; +#40327 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#40328 = EDGE_CURVE ( 'NONE', #42470, #13654, #100164, .T. ) ; +#40329 = AXIS2_PLACEMENT_3D ( 'NONE', #73906, #20770, #74404 ) ; +#40330 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#40331 = LINE ( 'NONE', #74985, #98823 ) ; +#40332 = VECTOR ( 'NONE', #73288, 1000.000000000000000 ) ; +#40333 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90902 ) ) ; +#40334 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, -0.02000000000002725292 ) ) ; +#40335 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21229, #44688, #89182 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40336 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40337 = VECTOR ( 'NONE', #55201, 1000.000000000000000 ) ; +#40338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85489, 'distance_accuracy_value', 'NONE'); +#40339 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #33789, #41444, #26633, #18426 ), + ( #50628, #18936, #49612, #4131 ), + ( #66417, #12211, #43432, #72560 ), + ( #2631, #74596, #42453, #35810 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541242845573, 0.8047378541242845573, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606230224, 0.6476030138606230224, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606230224, 0.6476030138606230224, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541242845573, 0.8047378541242845573, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#40340 = ORIENTED_EDGE ( 'NONE', *, *, #78300, .F. ) ; +#40341 = CLOSED_SHELL ( 'NONE', ( #27069, #69922, #65318, #70329, #57176, #92571 ) ) ; +#40342 = PLANE ( 'NONE', #63970 ) ; +#40343 = SURFACE_STYLE_FILL_AREA ( #39299 ) ; +#40344 = ORIENTED_EDGE ( 'NONE', *, *, #25317, .F. ) ; +#40345 = PRESENTATION_STYLE_ASSIGNMENT (( #9099 ) ) ; +#40346 = CIRCLE ( 'NONE', #77853, 0.09999999999999939493 ) ; +#40347 = CARTESIAN_POINT ( 'NONE', ( 1.870562122921110015, -1.007076035477679987, 0.8299999999999999600 ) ) ; +#40348 = CYLINDRICAL_SURFACE ( 'NONE', #45350, 0.1679250012421869831 ) ; +#40349 = SURFACE_SIDE_STYLE ('',( #58584 ) ) ; +#40350 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#40351 = SURFACE_STYLE_USAGE ( .BOTH. , #15286 ) ; +#40352 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62386, #10154, #41919 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40353 = VERTEX_POINT ( 'NONE', #46949 ) ; +#40354 = PRESENTATION_STYLE_ASSIGNMENT (( #73882 ) ) ; +#40355 = EDGE_LOOP ( 'NONE', ( #90480, #68488, #26359, #57673 ) ) ; +#40356 = SURFACE_SIDE_STYLE ('',( #48003 ) ) ; +#40357 = EDGE_CURVE ( 'NONE', #99969, #35471, #16286, .T. ) ; +#40358 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#40359 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999990674, -3.123820061220075051, 0.000000000000000000 ) ) ; +#40360 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#40361 = CYLINDRICAL_SURFACE ( 'NONE', #53764, 0.05000000000000012768 ) ; +#40362 = FILL_AREA_STYLE_COLOUR ( '', #40032 ) ; +#40363 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#40364 = EDGE_CURVE ( 'NONE', #39998, #28703, #489, .T. ) ; +#40365 = ORIENTED_EDGE ( 'NONE', *, *, #99603, .T. ) ; +#40366 = CARTESIAN_POINT ( 'NONE', ( 1.092224350139350264, -0.9825712221600161334, 0.8300000000000002931 ) ) ; +#40367 = ORIENTED_EDGE ( 'NONE', *, *, #70729, .T. ) ; +#40368 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40369 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13621 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18492, #79290, #49675 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40370 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40371 = ORIENTED_EDGE ( 'NONE', *, *, #23965, .T. ) ; +#40372 = LINE ( 'NONE', #2566, #28326 ) ; +#40373 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61589 ), #19128 ) ; +#40374 = CARTESIAN_POINT ( 'NONE', ( 1.050738163529689961, -1.365949044099890264, 0.8299999999999999600 ) ) ; +#40375 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40376 = CARTESIAN_POINT ( 'NONE', ( -2.123820061220085265, -3.100000000000000089, 0.000000000000000000 ) ) ; +#40377 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23506 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73475, #12092, #43313 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40379 = LINE ( 'NONE', #80200, #9992 ) ; +#40380 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40381 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#40383 = VERTEX_POINT ( 'NONE', #100453 ) ; +#40382 = ORIENTED_EDGE ( 'NONE', *, *, #18419, .F. ) ; +#40384 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66555, #97661, #74733, #90032 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40385 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40386 = LINE ( 'NONE', #26574, #78927 ) ; +#40387 = EDGE_LOOP ( 'NONE', ( #94248, #61813, #26869, #22322 ) ) ; +#40388 = STYLED_ITEM ( 'NONE', ( #90300 ), #84304 ) ; +#40389 = STYLED_ITEM ( 'NONE', ( #40073 ), #91179 ) ; +#40391 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000000001155, 0.000000000000000000 ) ) ; +#40390 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#40392 = VERTEX_POINT ( 'NONE', #38804 ) ; +#40393 = VECTOR ( 'NONE', #62444, 1000.000000000000000 ) ; +#40394 = ORIENTED_EDGE ( 'NONE', *, *, #89353, .T. ) ; +#40395 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#40396 = SURFACE_STYLE_FILL_AREA ( #86848 ) ; +#40397 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40399 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40398 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01500000000000000291, -0.1400000000000000411 ) ) ; +#40400 = FILL_AREA_STYLE ('',( #26089 ) ) ; +#40401 = ORIENTED_EDGE ( 'NONE', *, *, #24625, .F. ) ; +#40402 = EDGE_LOOP ( 'NONE', ( #42410, #45961, #58269, #47415 ) ) ; +#40403 = SURFACE_STYLE_FILL_AREA ( #18896 ) ; +#40404 = ORIENTED_EDGE ( 'NONE', *, *, #74002, .T. ) ; +#40405 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 3.287228999999999957, 0.8648700000000000276 ) ) ; +#40406 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40407 = VECTOR ( 'NONE', #73727, 1000.000000000000000 ) ; +#40408 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40410 = ORIENTED_EDGE ( 'NONE', *, *, #47216, .T. ) ; +#40409 = SURFACE_SIDE_STYLE ('',( #32745 ) ) ; +#40411 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16312 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #123, #37457, #60450 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40412 = LINE ( 'NONE', #33249, #21350 ) ; +#40413 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40415 = AXIS2_PLACEMENT_3D ( 'NONE', #53542, #37233, #74528 ) ; +#40414 = CARTESIAN_POINT ( 'NONE', ( 1.793184587716770029, -1.490633633148249926, 0.8099999999999996092 ) ) ; +#40416 = ORIENTED_EDGE ( 'NONE', *, *, #1377, .F. ) ; +#40417 = CLOSED_SHELL ( 'NONE', ( #58928, #95816, #1152, #60201, #27033, #24397 ) ) ; +#40418 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#40419 = ORIENTED_EDGE ( 'NONE', *, *, #94925, .F. ) ; +#40420 = STYLED_ITEM ( 'NONE', ( #97546 ), #40163 ) ; +#40421 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40422 = SURFACE_STYLE_FILL_AREA ( #32252 ) ; +#40423 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.90000000000000036, 0.000000000000000000 ) ) ; +#40424 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77861 ), #33873 ) ; +#40425 = SURFACE_SIDE_STYLE ('',( #56259 ) ) ; +#40427 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40426 = STYLED_ITEM ( 'NONE', ( #90761 ), #14888 ) ; +#40428 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40430 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#40429 = FILL_AREA_STYLE ('',( #72066 ) ) ; +#40431 = LINE ( 'NONE', #79742, #55617 ) ; +#40432 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37948 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63343, #72461, #94917 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40434 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 1.600000000000000089, -13.40000000000000036 ) ) ; +#40433 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #37058 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #65749 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#40435 = ORIENTED_EDGE ( 'NONE', *, *, #37774, .F. ) ; +#40436 = EDGE_CURVE ( 'NONE', #11704, #60396, #31145, .T. ) ; +#40437 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#40438 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706229E-17, 0.6700000000000000400, -0.1999999999999999833 ) ) ; +#40439 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67494, #11297, #19548, #34898 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40441 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#40440 = FACE_OUTER_BOUND ( 'NONE', #65346, .T. ) ; +#40442 = FILL_AREA_STYLE ('',( #50132 ) ) ; +#40443 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.383333333333326642, 0.000000000000000000 ) ) ; +#40444 = AXIS2_PLACEMENT_3D ( 'NONE', #24583, #40890, #80700 ) ; +#40445 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6097 ) ) ; +#40446 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40447 = ADVANCED_FACE ( 'NONE', ( #78114 ), #93385, .T. ) ; +#40448 = ORIENTED_EDGE ( 'NONE', *, *, #88742, .F. ) ; +#40449 = VECTOR ( 'NONE', #7312, 1000.000000000000000 ) ; +#40450 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999689, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#40451 = DIRECTION ( 'NONE', ( 0.9961493162234441590, -0.08767291364819879140, 0.000000000000000000 ) ) ; +#40452 = SURFACE_STYLE_FILL_AREA ( #9210 ) ; +#40453 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#40454 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89579 ), #66528 ) ; +#40455 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40456 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35590 ) ) ; +#40457 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#40458 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88253, 'distance_accuracy_value', 'NONE'); +#40459 = ORIENTED_EDGE ( 'NONE', *, *, #81449, .F. ) ; +#40460 = LINE ( 'NONE', #38432, #78363 ) ; +#40461 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7689 ), #53501 ) ; +#40462 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#40463 = LINE ( 'NONE', #23615, #46031 ) ; +#40464 = DIRECTION ( 'NONE', ( 0.7071067806865475314, 0.7071067816865476141, -0.000000000000000000 ) ) ; +#40465 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#40466 = AXIS2_PLACEMENT_3D ( 'NONE', #16514, #86500, #16022 ) ; +#40467 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#40468 = CARTESIAN_POINT ( 'NONE', ( 9.691234249749911100, 9.262280750250088346, 0.8991599999999999593 ) ) ; +#40469 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40470 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68009, #98582, #6186, #68521, #14368, #36410, #77193, #60904, #69008, #76196, #7169, #13326 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999968359, 0.3749999999999961142, 0.4374999999999958367, 0.4999999999999955591, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40471 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40472 = ADVANCED_FACE ( 'NONE', ( #50383 ), #16791, .T. ) ; +#40473 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#40474 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#40475 = VECTOR ( 'NONE', #61571, 1000.000000000000000 ) ; +#40476 = ORIENTED_EDGE ( 'NONE', *, *, #91793, .T. ) ; +#40477 = VERTEX_POINT ( 'NONE', #63333 ) ; +#40478 = AXIS2_PLACEMENT_3D ( 'NONE', #2996, #65273, #26495 ) ; +#40479 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40480 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21652, 'distance_accuracy_value', 'NONE'); +#40481 = SURFACE_SIDE_STYLE ('',( #85403 ) ) ; +#40482 = FILL_AREA_STYLE_COLOUR ( '', #99958 ) ; +#40484 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9407 ) ) ; +#40483 = PRESENTATION_STYLE_ASSIGNMENT (( #9234 ) ) ; +#40485 = PLANE ( 'NONE', #68877 ) ; +#40486 = FILL_AREA_STYLE_COLOUR ( '', #34202 ) ; +#40487 = VECTOR ( 'NONE', #83562, 1000.000000000000000 ) ; +#40488 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#40489 = FACE_OUTER_BOUND ( 'NONE', #4520, .T. ) ; +#40490 = CLOSED_SHELL ( 'NONE', ( #4990, #24749, #93407, #1646, #52756, #64501 ) ) ; +#40491 = EDGE_CURVE ( 'NONE', #57051, #26939, #24533, .T. ) ; +#40492 = ORIENTED_EDGE ( 'NONE', *, *, #24195, .F. ) ; +#40493 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999497, 0.8648700000000000276 ) ) ; +#40494 = LINE ( 'NONE', #10744, #40601 ) ; +#40495 = ORIENTED_EDGE ( 'NONE', *, *, #34363, .F. ) ; +#40496 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#40497 = SURFACE_STYLE_USAGE ( .BOTH. , #86438 ) ; +#40498 = ORIENTED_EDGE ( 'NONE', *, *, #16516, .F. ) ; +#40499 = VECTOR ( 'NONE', #58196, 1000.000000000000114 ) ; +#40500 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#40501 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40502 = SURFACE_STYLE_FILL_AREA ( #88452 ) ; +#40503 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#40504 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#40505 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#40506 = ORIENTED_EDGE ( 'NONE', *, *, #12088, .T. ) ; +#40508 = VECTOR ( 'NONE', #34842, 1000.000000000000000 ) ; +#40507 = PRESENTATION_STYLE_ASSIGNMENT (( #26196 ) ) ; +#40509 = LINE ( 'NONE', #65468, #46231 ) ; +#40510 = ORIENTED_EDGE ( 'NONE', *, *, #33847, .T. ) ; +#40511 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, 3.500000000000000444, 0.000000000000000000 ) ) ; +#40512 = CARTESIAN_POINT ( 'NONE', ( 1.414009484217380042, -1.031612284007709990, 0.8299999999999998490 ) ) ; +#40514 = EDGE_CURVE ( 'NONE', #26228, #38877, #60035, .T. ) ; +#40513 = ORIENTED_EDGE ( 'NONE', *, *, #8836, .T. ) ; +#40515 = SURFACE_STYLE_FILL_AREA ( #2710 ) ; +#40516 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #44934, .NOT_KNOWN. ) ; +#40517 = LINE ( 'NONE', #7743, #25069 ) ; +#40518 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11034 ), #73085 ) ; +#40519 = SURFACE_SIDE_STYLE ('',( #78305 ) ) ; +#40520 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#40521 = ORIENTED_EDGE ( 'NONE', *, *, #94361, .F. ) ; +#40523 = ORIENTED_EDGE ( 'NONE', *, *, #8601, .T. ) ; +#40522 = ORIENTED_EDGE ( 'NONE', *, *, #78167, .F. ) ; +#40524 = ORIENTED_EDGE ( 'NONE', *, *, #47708, .T. ) ; +#40525 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69777 ) ) ; +#40526 = ORIENTED_EDGE ( 'NONE', *, *, #95235, .T. ) ; +#40528 = ORIENTED_EDGE ( 'NONE', *, *, #22959, .F. ) ; +#40527 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40529 = AXIS2_PLACEMENT_3D ( 'NONE', #35482, #42118, #90576 ) ; +#40530 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6259 ), #9459 ) ; +#40531 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40533 = PLANE ( 'NONE', #54728 ) ; +#40532 = SURFACE_STYLE_FILL_AREA ( #94085 ) ; +#40534 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#40535 = FILL_AREA_STYLE ('',( #80342 ) ) ; +#40536 = VERTEX_POINT ( 'NONE', #15794 ) ; +#40537 = LINE ( 'NONE', #32865, #37455 ) ; +#40538 = SURFACE_STYLE_FILL_AREA ( #63525 ) ; +#40539 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8099999999998432898 ) ) ; +#40540 = ORIENTED_EDGE ( 'NONE', *, *, #63157, .F. ) ; +#40541 = EDGE_CURVE ( 'NONE', #64996, #33578, #15953, .T. ) ; +#40542 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64934 ), #68187 ) ; +#40543 = SURFACE_SIDE_STYLE ('',( #56388 ) ) ; +#40544 = EDGE_CURVE ( 'NONE', #71529, #19442, #50526, .T. ) ; +#40545 = FACE_OUTER_BOUND ( 'NONE', #68704, .T. ) ; +#40546 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40547 = EDGE_LOOP ( 'NONE', ( #49154, #3690, #27109, #84868 ) ) ; +#40548 = VECTOR ( 'NONE', #76692, 1000.000000000000000 ) ; +#40549 = ORIENTED_EDGE ( 'NONE', *, *, #53130, .F. ) ; +#40550 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40551 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40552 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40553 = LINE ( 'NONE', #32378, #1745 ) ; +#40554 = STYLED_ITEM ( 'NONE', ( #2420 ), #24788 ) ; +#40555 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74789 ) ) ; +#40556 = SURFACE_STYLE_USAGE ( .BOTH. , #49734 ) ; +#40557 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64950 ) ) ; +#40558 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40559 = EDGE_CURVE ( 'NONE', #54341, #9552, #26022, .T. ) ; +#40560 = ORIENTED_EDGE ( 'NONE', *, *, #88725, .F. ) ; +#40561 = SURFACE_STYLE_USAGE ( .BOTH. , #33911 ) ; +#40562 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19323 ), #9488 ) ; +#40563 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#40564 = SURFACE_SIDE_STYLE ('',( #53843 ) ) ; +#40565 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#40566 = CARTESIAN_POINT ( 'NONE', ( -0.9345478915627419836, -1.069424818316000003, 0.8100000000000000533 ) ) ; +#40567 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99121 ) ) ; +#40568 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40569 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40570 = CARTESIAN_POINT ( 'NONE', ( 3.999024875125043899, 5.267127124874957822, 0.8648700000000000276 ) ) ; +#40571 = ADVANCED_FACE ( 'NONE', ( #41342 ), #10076, .F. ) ; +#40572 = VERTEX_POINT ( 'NONE', #18310 ) ; +#40573 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40574 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40575 = STYLED_ITEM ( 'NONE', ( #54874 ), #50167 ) ; +#40576 = PLANE ( 'NONE', #78661 ) ; +#40577 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#40578 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50987, 'distance_accuracy_value', 'NONE'); +#40579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14282 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63355, #71486, #100477 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40580 = CARTESIAN_POINT ( 'NONE', ( 0.2346921643439940086, -1.433080367293090074, 0.8299999999999999600 ) ) ; +#40581 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980549, 0.000000000000000000 ) ) ; +#40582 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#40583 = EDGE_LOOP ( 'NONE', ( #98189, #90522, #67262, #18993 ) ) ; +#40584 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#40585 = FILL_AREA_STYLE_COLOUR ( '', #47787 ) ; +#40586 = LINE ( 'NONE', #25283, #60386 ) ; +#40587 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#40588 = FACE_OUTER_BOUND ( 'NONE', #82722, .T. ) ; +#40589 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11492 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43764, #19797, #28463 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40590 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40591 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40592 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40593 = VECTOR ( 'NONE', #61544, 1000.000000000000000 ) ; +#40594 = AXIS2_PLACEMENT_3D ( 'NONE', #80653, #97422, #81159 ) ; +#40595 = EDGE_CURVE ( 'NONE', #146, #6705, #34197, .T. ) ; +#40596 = FILL_AREA_STYLE ('',( #70703 ) ) ; +#40597 = SURFACE_SIDE_STYLE ('',( #9849 ) ) ; +#40598 = ORIENTED_EDGE ( 'NONE', *, *, #59515, .T. ) ; +#40599 = ORIENTED_EDGE ( 'NONE', *, *, #82497, .F. ) ; +#40600 = VECTOR ( 'NONE', #32101, 1000.000000000000000 ) ; +#40601 = VECTOR ( 'NONE', #59361, 1000.000000000000000 ) ; +#40603 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2750000000000000222, 0.1458578643762690474 ) ) ; +#40602 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40604 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#40605 = SURFACE_STYLE_USAGE ( .BOTH. , #47239 ) ; +#40606 = FILL_AREA_STYLE ('',( #94173 ) ) ; +#40607 = CARTESIAN_POINT ( 'NONE', ( -1.137533421400759970, -1.155903533527329996, 0.8299999999999999600 ) ) ; +#40608 = ADVANCED_FACE ( 'NONE', ( #9585 ), #1523, .T. ) ; +#40609 = ORIENTED_EDGE ( 'NONE', *, *, #9333, .F. ) ; +#40611 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8100000000001583711 ) ) ; +#40610 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40612 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47063 ) ) ; +#40613 = FACE_OUTER_BOUND ( 'NONE', #5325, .T. ) ; +#40614 = EDGE_LOOP ( 'NONE', ( #32649, #95483, #96685, #63633, #7883 ) ) ; +#40615 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40616 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40617 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72885 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49459, #1990, #87750 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40618 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40619 = AXIS2_PLACEMENT_3D ( 'NONE', #65195, #88676, #19214 ) ; +#40620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40621 = CARTESIAN_POINT ( 'NONE', ( -1.207523339372349902, -1.437310919031880241, 0.8299999999999999600 ) ) ; +#40622 = FACE_OUTER_BOUND ( 'NONE', #91964, .T. ) ; +#40623 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27583 ), #99180 ) ; +#40624 = VERTEX_POINT ( 'NONE', #96418 ) ; +#40625 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.300000000000000044, -0.02000000000002094894 ) ) ; +#40626 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11258, 'distance_accuracy_value', 'NONE'); +#40627 = LINE ( 'NONE', #30026, #15105 ) ; +#40628 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40629 = VECTOR ( 'NONE', #87367, 1000.000000000000000 ) ; +#40630 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #29492, #36175, #52484, #82137 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40631 = LINE ( 'NONE', #57989, #68206 ) ; +#40632 = ORIENTED_EDGE ( 'NONE', *, *, #28692, .T. ) ; +#40633 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40634 = ORIENTED_EDGE ( 'NONE', *, *, #89586, .T. ) ; +#40635 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.700000000000000178, 0.000000000000000000 ) ) ; +#40636 = FILL_AREA_STYLE ('',( #56488 ) ) ; +#40637 = SURFACE_STYLE_USAGE ( .BOTH. , #41647 ) ; +#40638 = EDGE_CURVE ( 'NONE', #27316, #93302, #26522, .T. ) ; +#40639 = EDGE_CURVE ( 'NONE', #16108, #67280, #17820, .T. ) ; +#40640 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40641 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89546 ) ) ; +#40642 = VERTEX_POINT ( 'NONE', #87784 ) ; +#40643 = VERTEX_POINT ( 'NONE', #50023 ) ; +#40644 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68091, 'distance_accuracy_value', 'NONE'); +#40645 = LINE ( 'NONE', #72277, #57298 ) ; +#40646 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999996980, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#40647 = SURFACE_SIDE_STYLE ('',( #33497 ) ) ; +#40648 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#40649 = VERTEX_POINT ( 'NONE', #49004 ) ; +#40650 = EDGE_CURVE ( 'NONE', #88429, #36462, #17414, .T. ) ; +#40651 = DIRECTION ( 'NONE', ( 4.344024262657780003E-34, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40652 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40653 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#40655 = ORIENTED_EDGE ( 'NONE', *, *, #45697, .F. ) ; +#40654 = AXIS2_PLACEMENT_3D ( 'NONE', #3846, #72799, #81978 ) ; +#40656 = EDGE_CURVE ( 'NONE', #52771, #72170, #42342, .T. ) ; +#40657 = SURFACE_STYLE_USAGE ( .BOTH. , #62642 ) ; +#40658 = ORIENTED_EDGE ( 'NONE', *, *, #39289, .T. ) ; +#40659 = VERTEX_POINT ( 'NONE', #96926 ) ; +#40660 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 2.597097883971776310E-17, -0.6199999999999999956 ) ) ; +#40661 = AXIS2_PLACEMENT_3D ( 'NONE', #60569, #68176, #99254 ) ; +#40662 = CARTESIAN_POINT ( 'NONE', ( 9.408391124875011613, 2.983172875124988188, 0.8648700000000000276 ) ) ; +#40663 = SURFACE_STYLE_FILL_AREA ( #84583 ) ; +#40664 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40665 = EDGE_LOOP ( 'NONE', ( #80922, #90355, #61627, #85205 ) ) ; +#40666 = STYLED_ITEM ( 'NONE', ( #24731 ), #57148 ) ; +#40667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40668 = AXIS2_PLACEMENT_3D ( 'NONE', #93172, #100746, #15577 ) ; +#40669 = EDGE_CURVE ( 'NONE', #53923, #40643, #27030, .T. ) ; +#40670 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40671 = ORIENTED_EDGE ( 'NONE', *, *, #47589, .F. ) ; +#40672 = SURFACE_STYLE_FILL_AREA ( #79480 ) ; +#40673 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40674 = VERTEX_POINT ( 'NONE', #19338 ) ; +#40675 = VERTEX_POINT ( 'NONE', #9088 ) ; +#40676 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40678 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40679 = FILL_AREA_STYLE_COLOUR ( '', #9317 ) ; +#40680 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40682 = EDGE_CURVE ( 'NONE', #26348, #14049, #40331, .T. ) ; +#40681 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40683 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40684 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 1.100000000000000089 ) ) ; +#40685 = SURFACE_SIDE_STYLE ('',( #57529 ) ) ; +#40686 = FILL_AREA_STYLE ('',( #10418 ) ) ; +#40687 = FACE_OUTER_BOUND ( 'NONE', #98220, .T. ) ; +#40688 = SURFACE_STYLE_USAGE ( .BOTH. , #94258 ) ; +#40689 = ADVANCED_FACE ( 'NONE', ( #90806 ), #44307, .T. ) ; +#40690 = EDGE_LOOP ( 'NONE', ( #11543, #80070, #5834, #10008 ) ) ; +#40691 = VECTOR ( 'NONE', #53032, 1000.000000000000000 ) ; +#40692 = CARTESIAN_POINT ( 'NONE', ( 8.404299750249974110, 10.54921475024997868, 0.8648700000000000276 ) ) ; +#40693 = EDGE_CURVE ( 'NONE', #61851, #61927, #55159, .T. ) ; +#40694 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40695 = SURFACE_STYLE_USAGE ( .BOTH. , #32535 ) ; +#40696 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40697 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#40698 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74863 ), #43951 ) ; +#40699 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#40700 = ADVANCED_FACE ( 'NONE', ( #52018 ), #4999, .F. ) ; +#40701 = LINE ( 'NONE', #65168, #93987 ) ; +#40702 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#40703 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40704 = SURFACE_STYLE_FILL_AREA ( #864 ) ; +#40705 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602299999999858, 0.8991599999999999593 ) ) ; +#40706 = PRODUCT_DEFINITION ( 'δ֪', '', #74762, #371 ) ; +#40707 = VERTEX_POINT ( 'NONE', #13109 ) ; +#40708 = CARTESIAN_POINT ( 'NONE', ( 0.6316964285714280480, 0.7099999999999999645, 0.5000000000000001110 ) ) ; +#40710 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68499, 'distance_accuracy_value', 'NONE'); +#40709 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40711 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40712 = SURFACE_STYLE_FILL_AREA ( #18174 ) ; +#40713 = FILL_AREA_STYLE_COLOUR ( '', #73952 ) ; +#40714 = SURFACE_STYLE_FILL_AREA ( #22337 ) ; +#40715 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40716 = FILL_AREA_STYLE ('',( #53999 ) ) ; +#40717 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#40718 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#40719 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#40720 = SURFACE_SIDE_STYLE ('',( #1400 ) ) ; +#40721 = ADVANCED_FACE ( 'NONE', ( #29010 ), #83653, .F. ) ; +#40722 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40723 = VECTOR ( 'NONE', #89696, 1000.000000000000000 ) ; +#40724 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40725 = FACE_OUTER_BOUND ( 'NONE', #20416, .T. ) ; +#40726 = FILL_AREA_STYLE ('',( #81049 ) ) ; +#40727 = SURFACE_STYLE_FILL_AREA ( #56569 ) ; +#40728 = EDGE_CURVE ( 'NONE', #39573, #75401, #20633, .T. ) ; +#40729 = ORIENTED_EDGE ( 'NONE', *, *, #83724, .T. ) ; +#40730 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#40731 = FILL_AREA_STYLE ('',( #48407 ) ) ; +#40732 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40733 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#40734 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29271 ) ) ; +#40736 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#40735 = CARTESIAN_POINT ( 'NONE', ( -0.03797038500300969899, -1.235192314287260062, 0.8300000000000002931 ) ) ; +#40737 = EDGE_CURVE ( 'NONE', #99535, #57973, #46305, .T. ) ; +#40738 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8099999999999502043 ) ) ; +#40739 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#40740 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39110 ) ) ; +#40741 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#40742 = ORIENTED_EDGE ( 'NONE', *, *, #27518, .T. ) ; +#40743 = PRESENTATION_STYLE_ASSIGNMENT (( #57082 ) ) ; +#40744 = EDGE_CURVE ( 'NONE', #6006, #42382, #84641, .T. ) ; +#40745 = FACE_OUTER_BOUND ( 'NONE', #94709, .T. ) ; +#40746 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33493 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2608, #33760, #48064 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40747 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40748 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19519 ) ) ; +#40749 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#40750 = ORIENTED_EDGE ( 'NONE', *, *, #37921, .T. ) ; +#40751 = ORIENTED_EDGE ( 'NONE', *, *, #58868, .T. ) ; +#40752 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45562 ) ) ; +#40753 = ORIENTED_EDGE ( 'NONE', *, *, #23903, .F. ) ; +#40754 = LINE ( 'NONE', #23934, #70567 ) ; +#40755 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.266666666666667052, 0.000000000000000000 ) ) ; +#40756 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40757 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40758 = EDGE_CURVE ( 'NONE', #92247, #57887, #37691, .T. ) ; +#40759 = SHAPE_DEFINITION_REPRESENTATION ( #92258, #33171 ) ; +#40760 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40761 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#40763 = ORIENTED_EDGE ( 'NONE', *, *, #36373, .F. ) ; +#40762 = ORIENTED_EDGE ( 'NONE', *, *, #73477, .T. ) ; +#40764 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83175 ) ) ; +#40765 = AXIS2_PLACEMENT_3D ( 'NONE', #65266, #40799, #24990 ) ; +#40766 = ORIENTED_EDGE ( 'NONE', *, *, #64586, .T. ) ; +#40767 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12842, 'distance_accuracy_value', 'NONE'); +#40768 = SURFACE_STYLE_FILL_AREA ( #85694 ) ; +#40770 = SURFACE_SIDE_STYLE ('',( #62246 ) ) ; +#40769 = FILL_AREA_STYLE ('',( #33097 ) ) ; +#40771 = ORIENTED_EDGE ( 'NONE', *, *, #33283, .T. ) ; +#40772 = LINE ( 'NONE', #95344, #37554 ) ; +#40773 = EDGE_CURVE ( 'NONE', #68004, #81283, #68787, .T. ) ; +#40774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61985 ) ) ; +#40775 = ORIENTED_EDGE ( 'NONE', *, *, #35543, .T. ) ; +#40776 = FILL_AREA_STYLE_COLOUR ( '', #23779 ) ; +#40777 = VERTEX_POINT ( 'NONE', #46824 ) ; +#40778 = EDGE_CURVE ( 'NONE', #19807, #86302, #33712, .T. ) ; +#40779 = SURFACE_STYLE_FILL_AREA ( #57123 ) ; +#40780 = VERTEX_POINT ( 'NONE', #7949 ) ; +#40781 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53739, #77211, #62425, #93999 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40782 = EDGE_LOOP ( 'NONE', ( #19690, #30184, #51304, #67123 ) ) ; +#40783 = VECTOR ( 'NONE', #97045, 1000.000000000000114 ) ; +#40784 = CARTESIAN_POINT ( 'NONE', ( 0.2835602027787479940, -1.357109198394020000, 0.8300000000000004041 ) ) ; +#40785 = SURFACE_STYLE_USAGE ( .BOTH. , #42295 ) ; +#40787 = ORIENTED_EDGE ( 'NONE', *, *, #38386, .F. ) ; +#40786 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63357 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31685, #38850, #46474 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40788 = LINE ( 'NONE', #68248, #10621 ) ; +#40789 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#40790 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #47920, #70904, #72791, #96241 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40791 = CARTESIAN_POINT ( 'NONE', ( -0.2880456131010220022, -1.031932509624869931, 0.8100000000000000533 ) ) ; +#40792 = PLANE ( 'NONE', #48982 ) ; +#40793 = ORIENTED_EDGE ( 'NONE', *, *, #84662, .F. ) ; +#40795 = FILL_AREA_STYLE_COLOUR ( '', #55084 ) ; +#40794 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#40796 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#40797 = VERTEX_POINT ( 'NONE', #45298 ) ; +#40798 = EDGE_LOOP ( 'NONE', ( #27730, #47148, #50560, #67470 ) ) ; +#40800 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#40799 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40801 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#40803 = EDGE_CURVE ( 'NONE', #95195, #65218, #39180, .T. ) ; +#40802 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40804 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99356 ) ) ; +#40805 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8100000000000000533 ) ) ; +#40806 = PRESENTATION_STYLE_ASSIGNMENT (( #63791 ) ) ; +#40807 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#40808 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78331 ), #88104 ) ; +#40809 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48992, 'distance_accuracy_value', 'NONE'); +#40810 = EDGE_CURVE ( 'NONE', #41762, #66411, #361, .T. ) ; +#40811 = VECTOR ( 'NONE', #34694, 1000.000000000000000 ) ; +#40812 = ORIENTED_EDGE ( 'NONE', *, *, #13198, .F. ) ; +#40813 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#40814 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40815 = ORIENTED_EDGE ( 'NONE', *, *, #31958, .T. ) ; +#40816 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40818 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#40817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66878 ), #8043 ) ; +#40819 = LINE ( 'NONE', #32143, #14140 ) ; +#40820 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94559 ) ) ; +#40821 = DIRECTION ( 'NONE', ( -0.7071067811865469066, 0.7071067811865482389, 0.000000000000000000 ) ) ; +#40822 = FILL_AREA_STYLE ('',( #80637 ) ) ; +#40824 = SURFACE_SIDE_STYLE ('',( #3008 ) ) ; +#40823 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40825 = FILL_AREA_STYLE_COLOUR ( '', #56964 ) ; +#40826 = FILL_AREA_STYLE ('',( #2008 ) ) ; +#40827 = DIRECTION ( 'NONE', ( 2.168404344971010051E-15, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40828 = AXIS2_PLACEMENT_3D ( 'NONE', #26205, #86967, #25219 ) ; +#40829 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40830 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#40831 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#40832 = STYLED_ITEM ( 'NONE', ( #94413 ), #80734 ) ; +#40833 = CARTESIAN_POINT ( 'NONE', ( -1.291038328540720093, -1.030374455384980070, 0.8299999999999998490 ) ) ; +#40834 = STYLED_ITEM ( 'NONE', ( #18694 ), #65307 ) ; +#40835 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40836 = AXIS2_PLACEMENT_3D ( 'NONE', #41196, #10425, #2388 ) ; +#40837 = EDGE_CURVE ( 'NONE', #85854, #67944, #16172, .T. ) ; +#40838 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8991599999999999593 ) ) ; +#40839 = STYLED_ITEM ( 'NONE', ( #71713 ), #1894 ) ; +#40840 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40841 = FACE_OUTER_BOUND ( 'NONE', #81099, .T. ) ; +#40842 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8770 ) ) ; +#40843 = EDGE_LOOP ( 'NONE', ( #17842, #65756, #17602, #74175 ) ) ; +#40844 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8991599999999999593 ) ) ; +#40845 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#40846 = EDGE_CURVE ( 'NONE', #41162, #75369, #100830, .T. ) ; +#40847 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88463, 'distance_accuracy_value', 'NONE'); +#40848 = ORIENTED_EDGE ( 'NONE', *, *, #12797, .T. ) ; +#40850 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77328, 'distance_accuracy_value', 'NONE'); +#40849 = FILL_AREA_STYLE_COLOUR ( '', #23851 ) ; +#40851 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40852 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#40853 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40854 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18467 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89181, #58574, #82037 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40855 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#40856 = ADVANCED_FACE ( 'NONE', ( #8448 ), #92290, .T. ) ; +#40857 = PRESENTATION_STYLE_ASSIGNMENT (( #3040 ) ) ; +#40858 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53137 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63595, #8846, #38402 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40859 = FACE_OUTER_BOUND ( 'NONE', #26543, .T. ) ; +#40860 = ORIENTED_EDGE ( 'NONE', *, *, #42294, .T. ) ; +#40861 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40862 = EDGE_LOOP ( 'NONE', ( #8990, #83541, #69429, #23929 ) ) ; +#40863 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#40864 = EDGE_CURVE ( 'NONE', #70863, #88609, #79503, .T. ) ; +#40865 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89585, 'distance_accuracy_value', 'NONE'); +#40866 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, 3.500000000000000444, 0.000000000000000000 ) ) ; +#40867 = PLANE ( 'NONE', #44727 ) ; +#40868 = DIRECTION ( 'NONE', ( -0.7071064476869688420, 0.7071071146859688739, -0.000000000000000000 ) ) ; +#40869 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40870 = SURFACE_STYLE_USAGE ( .BOTH. , #26056 ) ; +#40871 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40872 = EDGE_CURVE ( 'NONE', #76548, #37943, #16664, .T. ) ; +#40873 = EDGE_LOOP ( 'NONE', ( #41906, #48516, #99613, #30934 ) ) ; +#40874 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#40875 = ORIENTED_EDGE ( 'NONE', *, *, #57451, .F. ) ; +#40876 = LINE ( 'NONE', #83057, #40943 ) ; +#40877 = VECTOR ( 'NONE', #11938, 1000.000000000000000 ) ; +#40878 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37085 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81066, #66222, #19761 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40879 = LINE ( 'NONE', #66357, #69934 ) ; +#40880 = VERTEX_POINT ( 'NONE', #81041 ) ; +#40881 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#40882 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40883 = CARTESIAN_POINT ( 'NONE', ( 3.822247500500175033, 8.003630500500175771, 0.8991599999999999593 ) ) ; +#40884 = ADVANCED_FACE ( 'NONE', ( #71337 ), #94791, .T. ) ; +#40885 = ADVANCED_FACE ( 'NONE', ( #10447 ), #2915, .T. ) ; +#40886 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40887 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76703 ), #39242 ) ; +#40888 = VECTOR ( 'NONE', #84469, 1000.000000000000114 ) ; +#40889 = VECTOR ( 'NONE', #27025, 1000.000000000000114 ) ; +#40890 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40891 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40892 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 1.445602896647339903E-15 ) ) ; +#40893 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8991599999999999593 ) ) ; +#40895 = ORIENTED_EDGE ( 'NONE', *, *, #47551, .F. ) ; +#40894 = ORIENTED_EDGE ( 'NONE', *, *, #55726, .T. ) ; +#40897 = SURFACE_STYLE_FILL_AREA ( #86835 ) ; +#40896 = CIRCLE ( 'NONE', #97878, 0.2000000000000000111 ) ; +#40898 = EDGE_CURVE ( 'NONE', #69034, #84546, #67364, .T. ) ; +#40899 = EDGE_CURVE ( 'NONE', #65277, #22958, #49367, .T. ) ; +#40900 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42995, #43998, #10755 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40901 = ORIENTED_EDGE ( 'NONE', *, *, #72930, .F. ) ; +#40902 = VECTOR ( 'NONE', #97274, 1000.000000000000000 ) ; +#40903 = SURFACE_STYLE_FILL_AREA ( #39346 ) ; +#40904 = ORIENTED_EDGE ( 'NONE', *, *, #100222, .T. ) ; +#40905 = ORIENTED_EDGE ( 'NONE', *, *, #85040, .F. ) ; +#40906 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21339 ) ) ; +#40907 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40908 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#40909 = EDGE_CURVE ( 'NONE', #28925, #38466, #52390, .T. ) ; +#40910 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#40911 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#40912 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#40913 = ORIENTED_EDGE ( 'NONE', *, *, #76456, .T. ) ; +#40914 = EDGE_LOOP ( 'NONE', ( #33502, #1053, #4699, #36536, #81433, #36702 ) ) ; +#40915 = SURFACE_SIDE_STYLE ('',( #34264 ) ) ; +#40916 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79551, #71890, #65741, #95324 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#40917 = ORIENTED_EDGE ( 'NONE', *, *, #89586, .F. ) ; +#40918 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80916 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75329, #4376, #3875 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#40919 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#40920 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#40921 = ORIENTED_EDGE ( 'NONE', *, *, #1945, .F. ) ; +#40922 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.9000000000000007994, 0.000000000000000000 ) ) ; +#40923 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#40924 = SURFACE_STYLE_FILL_AREA ( #1081 ) ; +#40925 = EDGE_LOOP ( 'NONE', ( #16116, #71294, #15098, #86565, #20406, #57136 ) ) ; +#40926 = CARTESIAN_POINT ( 'NONE', ( 9.535670875125044077, 3.110451875125043841, 0.8991599999999999593 ) ) ; +#40927 = LINE ( 'NONE', #17892, #81949 ) ; +#40928 = ORIENTED_EDGE ( 'NONE', *, *, #85311, .T. ) ; +#40929 = FILL_AREA_STYLE ('',( #18406 ) ) ; +#40930 = SURFACE_STYLE_FILL_AREA ( #79730 ) ; +#40931 = VECTOR ( 'NONE', #19089, 1000.000000000000000 ) ; +#40932 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#40933 = FACE_OUTER_BOUND ( 'NONE', #87023, .T. ) ; +#40934 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40936 = FILL_AREA_STYLE ('',( #2122 ) ) ; +#40935 = SURFACE_STYLE_FILL_AREA ( #40429 ) ; +#40937 = CARTESIAN_POINT ( 'NONE', ( 1.644292209069110111, -0.9726617844338859564, 0.8299999999999990719 ) ) ; +#40938 = ORIENTED_EDGE ( 'NONE', *, *, #25393, .T. ) ; +#40939 = SURFACE_STYLE_USAGE ( .BOTH. , #88389 ) ; +#40940 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#40941 = ORIENTED_EDGE ( 'NONE', *, *, #72868, .T. ) ; +#40942 = ADVANCED_FACE ( 'NONE', ( #67184 ), #74365, .T. ) ; +#40943 = VECTOR ( 'NONE', #67215, 1000.000000000000000 ) ; +#40944 = PLANE ( 'NONE', #27281 ) ; +#40945 = SURFACE_STYLE_USAGE ( .BOTH. , #1105 ) ; +#40946 = LINE ( 'NONE', #72076, #22099 ) ; +#40947 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4808578643762689842, 0.2399999999999999356 ) ) ; +#40948 = ADVANCED_FACE ( 'NONE', ( #4885 ), #73862, .T. ) ; +#40950 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#40949 = LINE ( 'NONE', #86890, #18522 ) ; +#40951 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#40952 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -9.880000000000000782, 0.2999999999999999889 ) ) ; +#40953 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45761 ) ) ; +#40954 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#40955 = PRESENTATION_STYLE_ASSIGNMENT (( #33290 ) ) ; +#40956 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57286 ), #58907 ) ; +#40957 = VERTEX_POINT ( 'NONE', #27920 ) ; +#40958 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14783 ), #21391 ) ; +#40959 = FILL_AREA_STYLE_COLOUR ( '', #3091 ) ; +#40960 = EDGE_CURVE ( 'NONE', #28607, #93440, #4445, .T. ) ; +#40962 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40961 = LINE ( 'NONE', #78717, #54006 ) ; +#40963 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2999999999999999889, -13.40000000000000036 ) ) ; +#40964 = VECTOR ( 'NONE', #70023, 1000.000000000000000 ) ; +#40965 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.300000000000000266, -0.02000000000004190093 ) ) ; +#40966 = PRESENTATION_STYLE_ASSIGNMENT (( #63931 ) ) ; +#40967 = PLANE ( 'NONE', #44513 ) ; +#40968 = ORIENTED_EDGE ( 'NONE', *, *, #79229, .T. ) ; +#40969 = FACE_OUTER_BOUND ( 'NONE', #34112, .T. ) ; +#40970 = EDGE_CURVE ( 'NONE', #23531, #43001, #59074, .T. ) ; +#40971 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31108 ) ) ; +#40972 = SURFACE_STYLE_USAGE ( .BOTH. , #94538 ) ; +#40973 = SURFACE_SIDE_STYLE ('',( #79772 ) ) ; +#40974 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, 0.000000000000000000 ) ) ; +#40975 = LINE ( 'NONE', #8700, #99084 ) ; +#40976 = SURFACE_STYLE_FILL_AREA ( #56307 ) ; +#40977 = VECTOR ( 'NONE', #78134, 1000.000000000000000 ) ; +#40978 = PLANE ( 'NONE', #32872 ) ; +#40979 = CARTESIAN_POINT ( 'NONE', ( -0.9967138265693971100, -1.378727886756609955, 0.8300000000000001821 ) ) ; +#40980 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40981 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28673, 'distance_accuracy_value', 'NONE'); +#40982 = AXIS2_PLACEMENT_3D ( 'NONE', #55769, #62938, #56798 ) ; +#40983 = SURFACE_STYLE_USAGE ( .BOTH. , #62960 ) ; +#40984 = ORIENTED_EDGE ( 'NONE', *, *, #37840, .T. ) ; +#40985 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#40986 = ORIENTED_EDGE ( 'NONE', *, *, #83396, .T. ) ; +#40987 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#40988 = EDGE_CURVE ( 'NONE', #15311, #32313, #51397, .T. ) ; +#40990 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28019, 'distance_accuracy_value', 'NONE'); +#40989 = STYLED_ITEM ( 'NONE', ( #48572 ), #69588 ) ; +#40991 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69250, 'distance_accuracy_value', 'NONE'); +#40992 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40993 = PRESENTATION_STYLE_ASSIGNMENT (( #10735 ) ) ; +#40994 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40995 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#40996 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#40997 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#40998 = SURFACE_SIDE_STYLE ('',( #79792 ) ) ; +#40999 = EDGE_CURVE ( 'NONE', #92532, #60383, #43697, .T. ) ; +#41000 = VERTEX_POINT ( 'NONE', #36077 ) ; +#41001 = FACE_OUTER_BOUND ( 'NONE', #87213, .T. ) ; +#41002 = FILL_AREA_STYLE ('',( #48655 ) ) ; +#41003 = LINE ( 'NONE', #2187, #68841 ) ; +#41004 = ORIENTED_EDGE ( 'NONE', *, *, #23821, .T. ) ; +#41005 = SURFACE_STYLE_USAGE ( .BOTH. , #35367 ) ; +#41006 = PRESENTATION_STYLE_ASSIGNMENT (( #1695 ) ) ; +#41007 = VECTOR ( 'NONE', #77470, 1000.000000000000000 ) ; +#41008 = EDGE_LOOP ( 'NONE', ( #14580, #52282, #91989, #44971 ) ) ; +#41009 = STYLED_ITEM ( 'NONE', ( #37253 ), #46103 ) ; +#41010 = VECTOR ( 'NONE', #17874, 1000.000000000000000 ) ; +#41011 = FACE_OUTER_BOUND ( 'NONE', #51877, .T. ) ; +#41012 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#41013 = LINE ( 'NONE', #16976, #11539 ) ; +#41014 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#41015 = ORIENTED_EDGE ( 'NONE', *, *, #19055, .F. ) ; +#41016 = VECTOR ( 'NONE', #33988, 1000.000000000000114 ) ; +#41018 = EDGE_CURVE ( 'NONE', #90383, #67231, #98261, .T. ) ; +#41017 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41019 = ADVANCED_FACE ( 'NONE', ( #62074 ), #61066, .T. ) ; +#41020 = EDGE_LOOP ( 'NONE', ( #17135, #16077, #11544, #83075 ) ) ; +#41021 = ORIENTED_EDGE ( 'NONE', *, *, #10861, .T. ) ; +#41022 = LINE ( 'NONE', #97103, #56318 ) ; +#41024 = EDGE_CURVE ( 'NONE', #24202, #74624, #31400, .T. ) ; +#41023 = CARTESIAN_POINT ( 'NONE', ( 3.822248499500052521, 4.524665499500048149, 0.8991599999999999593 ) ) ; +#41025 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71984 ), #75264 ) ; +#41026 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41027 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41028 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8099999999999827338 ) ) ; +#41029 = ORIENTED_EDGE ( 'NONE', *, *, #34163, .F. ) ; +#41031 = ORIENTED_EDGE ( 'NONE', *, *, #73158, .F. ) ; +#41030 = ORIENTED_EDGE ( 'NONE', *, *, #32071, .T. ) ; +#41032 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41033 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100937 ) ; +#41034 = EDGE_LOOP ( 'NONE', ( #33524, #55627, #27906, #100653 ) ) ; +#41035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76930 ) ) ; +#41036 = EDGE_CURVE ( 'NONE', #19644, #14561, #15543, .T. ) ; +#41037 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, 0.000000000000000000 ) ) ; +#41038 = VECTOR ( 'NONE', #20435, 1000.000000000000114 ) ; +#41039 = ORIENTED_EDGE ( 'NONE', *, *, #44444, .F. ) ; +#41040 = ORIENTED_EDGE ( 'NONE', *, *, #31418, .T. ) ; +#41041 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#41042 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#41043 = PLANE ( 'NONE', #100188 ) ; +#41044 = FILL_AREA_STYLE ('',( #32362 ) ) ; +#41045 = VERTEX_POINT ( 'NONE', #38067 ) ; +#41046 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41047 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41048 = PRESENTATION_STYLE_ASSIGNMENT (( #25718 ) ) ; +#41049 = EDGE_LOOP ( 'NONE', ( #35620, #94858, #33761, #97695 ) ) ; +#41050 = STYLED_ITEM ( 'NONE', ( #43515 ), #7529 ) ; +#41051 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#41052 = DIRECTION ( 'NONE', ( -0.7071067816865476141, -0.7071067806865475314, 0.000000000000000000 ) ) ; +#41053 = CARTESIAN_POINT ( 'NONE', ( 0.4933869866146596284, 0.5990590759269652787, 0.8100000000000000533 ) ) ; +#41054 = EDGE_LOOP ( 'NONE', ( #18534, #74035, #83823, #74046, #72916, #31180, #42938, #33692 ) ) ; +#41055 = VECTOR ( 'NONE', #38697, 1000.000000000000000 ) ; +#41056 = VERTEX_POINT ( 'NONE', #38563 ) ; +#41057 = LINE ( 'NONE', #72179, #91864 ) ; +#41058 = SURFACE_SIDE_STYLE ('',( #25251 ) ) ; +#41059 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#41060 = STYLED_ITEM ( 'NONE', ( #45710 ), #2596 ) ; +#41061 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#41062 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91314 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86589, #94729, #76534 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41063 = FACE_OUTER_BOUND ( 'NONE', #95807, .T. ) ; +#41064 = VECTOR ( 'NONE', #68190, 1000.000000000000000 ) ; +#41065 = ADVANCED_FACE ( 'NONE', ( #46705 ), #251, .T. ) ; +#41066 = SURFACE_SIDE_STYLE ('',( #33399 ) ) ; +#41067 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#41068 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28651 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38066, #54401, #71723 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41069 = CARTESIAN_POINT ( 'NONE', ( -0.9858361255783950616, -0.9444486738239200596, 0.8100000000000010525 ) ) ; +#41070 = CARTESIAN_POINT ( 'NONE', ( 1.157135261321870168, -0.8867570690059840555, 0.8100000000000000533 ) ) ; +#41071 = EDGE_LOOP ( 'NONE', ( #3720, #75626, #99698, #29676 ) ) ; +#41072 = FILL_AREA_STYLE ('',( #33407 ) ) ; +#41073 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50300 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11533, #41766, #34128 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41074 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#41075 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8100000000000001643 ) ) ; +#41076 = EDGE_LOOP ( 'NONE', ( #25842, #40164, #89800, #76285 ) ) ; +#41077 = CARTESIAN_POINT ( 'NONE', ( -0.9202467668417529945, -1.279077976066830047, 0.8300000000000002931 ) ) ; +#41079 = LINE ( 'NONE', #57407, #88132 ) ; +#41078 = FILL_AREA_STYLE_COLOUR ( '', #46332 ) ; +#41080 = CARTESIAN_POINT ( 'NONE', ( 1.592240980523090155, -1.399421068953930147, 0.8099999999999976108 ) ) ; +#41081 = CIRCLE ( 'NONE', #86685, 0.2000000000000005107 ) ; +#41082 = CARTESIAN_POINT ( 'NONE', ( -0.2079889469064460095, -1.408946430034399899, 0.8100000000000010525 ) ) ; +#41083 = CARTESIAN_POINT ( 'NONE', ( 0.3732565376499660248, -1.295998480396600039, 0.8299999999999999600 ) ) ; +#41084 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.000000000000000000 ) ) ; +#41085 = LINE ( 'NONE', #25278, #31420 ) ; +#41086 = FILL_AREA_STYLE_COLOUR ( '', #5377 ) ; +#41087 = ORIENTED_EDGE ( 'NONE', *, *, #93067, .F. ) ; +#41088 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41089 = EDGE_CURVE ( 'NONE', #31665, #7232, #94058, .T. ) ; +#41090 = FILL_AREA_STYLE_COLOUR ( '', #16287 ) ; +#41091 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#41092 = FILL_AREA_STYLE ('',( #32414 ) ) ; +#41093 = LINE ( 'NONE', #88044, #50248 ) ; +#41094 = VECTOR ( 'NONE', #91826, 1000.000000000000000 ) ; +#41095 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41096 = SURFACE_STYLE_USAGE ( .BOTH. , #25772 ) ; +#41097 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41098 = LINE ( 'NONE', #71720, #22434 ) ; +#41099 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41100 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41102 = STYLED_ITEM ( 'NONE', ( #93882 ), #43328 ) ; +#41101 = PRESENTATION_STYLE_ASSIGNMENT (( #26784 ) ) ; +#41103 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31150 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77481, #31542, #94801 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41104 = PLANE ( 'NONE', #16369 ) ; +#41105 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#41106 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#41107 = ORIENTED_EDGE ( 'NONE', *, *, #18550, .F. ) ; +#41109 = EDGE_LOOP ( 'NONE', ( #51042, #46521, #71068, #34884 ) ) ; +#41108 = AXIS2_PLACEMENT_3D ( 'NONE', #95212, #79955, #10385 ) ; +#41110 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83340, 'distance_accuracy_value', 'NONE'); +#41111 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57685, 'distance_accuracy_value', 'NONE'); +#41112 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41113 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41114 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#41115 = FILL_AREA_STYLE ('',( #56954 ) ) ; +#41116 = STYLED_ITEM ( 'NONE', ( #8894 ), #10983 ) ; +#41117 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909090329, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#41118 = PLANE ( 'NONE', #4327 ) ; +#41119 = ADVANCED_FACE ( 'NONE', ( #52902 ), #84024, .T. ) ; +#41120 = ORIENTED_EDGE ( 'NONE', *, *, #296, .T. ) ; +#41121 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41122 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41123 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79576, 'distance_accuracy_value', 'NONE'); +#41124 = FILL_AREA_STYLE_COLOUR ( '', #348 ) ; +#41125 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#41126 = VECTOR ( 'NONE', #70080, 1000.000000000000000 ) ; +#41127 = ORIENTED_EDGE ( 'NONE', *, *, #56427, .T. ) ; +#41128 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41129 = LINE ( 'NONE', #11880, #78902 ) ; +#41130 = EDGE_LOOP ( 'NONE', ( #14279, #190, #7119, #46090 ) ) ; +#41131 = EDGE_CURVE ( 'NONE', #88085, #5748, #49776, .T. ) ; +#41132 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1748, 'distance_accuracy_value', 'NONE'); +#41133 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#41134 = VERTEX_POINT ( 'NONE', #2299 ) ; +#41135 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#41136 = SURFACE_SIDE_STYLE ('',( #72775 ) ) ; +#41137 = FILL_AREA_STYLE_COLOUR ( '', #54079 ) ; +#41138 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#41139 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41140 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41141 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41142 = SURFACE_STYLE_USAGE ( .BOTH. , #18103 ) ; +#41143 = EDGE_CURVE ( 'NONE', #14910, #92376, #49258, .T. ) ; +#41144 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #97187, #99691 ) ; +#41145 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2002 ), #8797 ) ; +#41146 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75380 ), #36268 ) ; +#41147 = ORIENTED_EDGE ( 'NONE', *, *, #47504, .T. ) ; +#41149 = EDGE_LOOP ( 'NONE', ( #54147, #80662, #55561, #24204 ) ) ; +#41148 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41150 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41152 = SURFACE_SIDE_STYLE ('',( #88598 ) ) ; +#41151 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#41153 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.323820061220084998, -0.02000000000000000042 ) ) ; +#41154 = CARTESIAN_POINT ( 'NONE', ( -0.9833333333333335036, 3.099999999999989875, 0.000000000000000000 ) ) ; +#41155 = ORIENTED_EDGE ( 'NONE', *, *, #15994, .F. ) ; +#41156 = FILL_AREA_STYLE_COLOUR ( '', #84191 ) ; +#41157 = LINE ( 'NONE', #47795, #94656 ) ; +#41158 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41159 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46037 ) ) ; +#41160 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83494 ) ) ; +#41161 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41162 = VERTEX_POINT ( 'NONE', #41105 ) ; +#41163 = EDGE_LOOP ( 'NONE', ( #20699, #23400, #82199, #69118 ) ) ; +#41164 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80305 ), #68806 ) ; +#41165 = ORIENTED_EDGE ( 'NONE', *, *, #22355, .F. ) ; +#41166 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100034, #29695, #21535, #52696 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#41167 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1199999999999999956, -0.8499999999999997558 ) ) ; +#41169 = PLANE ( 'NONE', #87493 ) ; +#41168 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#41170 = CARTESIAN_POINT ( 'NONE', ( 0.6702516233766230291, 0.6899999999999999467, 0.4397321428571429602 ) ) ; +#41171 = VECTOR ( 'NONE', #67594, 1000.000000000000000 ) ; +#41172 = ORIENTED_EDGE ( 'NONE', *, *, #91253, .T. ) ; +#41173 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41174 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#41175 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34705 ), #98151 ) ; +#41176 = ORIENTED_EDGE ( 'NONE', *, *, #95409, .F. ) ; +#41177 = SURFACE_STYLE_USAGE ( .BOTH. , #31995 ) ; +#41178 = ORIENTED_EDGE ( 'NONE', *, *, #79675, .F. ) ; +#41179 = VERTEX_POINT ( 'NONE', #32927 ) ; +#41180 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41181 = EDGE_CURVE ( 'NONE', #64088, #29895, #16553, .T. ) ; +#41182 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41183 = CARTESIAN_POINT ( 'NONE', ( -1.049523990565160103, -1.254158608853950030, 0.8299999999999999600 ) ) ; +#41184 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52624 ), #67243 ) ; +#41185 = CARTESIAN_POINT ( 'NONE', ( 1.027124486614660270, 0.8310340759269650990, 0.8299999999999999600 ) ) ; +#41186 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94923 ), #73757 ) ; +#41187 = PLANE ( 'NONE', #45909 ) ; +#41188 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8648700000000000276 ) ) ; +#41189 = FACE_OUTER_BOUND ( 'NONE', #64503, .T. ) ; +#41190 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#41191 = STYLED_ITEM ( 'NONE', ( #80804 ), #25623 ) ; +#41192 = ORIENTED_EDGE ( 'NONE', *, *, #94875, .T. ) ; +#41193 = SURFACE_STYLE_USAGE ( .BOTH. , #3390 ) ; +#41194 = DIRECTION ( 'NONE', ( -0.7071090539100453043, -0.7071045084557450178, 0.000000000000000000 ) ) ; +#41195 = VECTOR ( 'NONE', #41920, 1000.000000000000000 ) ; +#41197 = FACE_OUTER_BOUND ( 'NONE', #65292, .T. ) ; +#41196 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#41198 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8991599999999999593 ) ) ; +#41199 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41200 = LINE ( 'NONE', #24386, #36986 ) ; +#41201 = LINE ( 'NONE', #9947, #68094 ) ; +#41202 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45937 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100486, #14798, #54164 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41203 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41204 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41205 = ORIENTED_EDGE ( 'NONE', *, *, #98573, .T. ) ; +#41206 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8199999999999999512 ) ) ; +#41207 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41208 = SURFACE_STYLE_USAGE ( .BOTH. , #40202 ) ; +#41209 = FILL_AREA_STYLE_COLOUR ( '', #96914 ) ; +#41210 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333329751, 1.500000000000000000, 0.000000000000000000 ) ) ; +#41211 = AXIS2_PLACEMENT_3D ( 'NONE', #54386, #16042, #4993 ) ; +#41212 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31667 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24927, #69820, #63220 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41213 = LINE ( 'NONE', #62193, #69205 ) ; +#41214 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16889, 'distance_accuracy_value', 'NONE'); +#41215 = FACE_OUTER_BOUND ( 'NONE', #66827, .T. ) ; +#41216 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41218 = EDGE_CURVE ( 'NONE', #4091, #94313, #86540, .T. ) ; +#41217 = VECTOR ( 'NONE', #1473, 1000.000000000000000 ) ; +#41219 = EDGE_CURVE ( 'NONE', #59404, #94145, #49129, .T. ) ; +#41220 = SURFACE_STYLE_FILL_AREA ( #88176 ) ; +#41221 = FACE_OUTER_BOUND ( 'NONE', #60808, .T. ) ; +#41222 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41223 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.000000000000000000 ) ) ; +#41224 = CYLINDRICAL_SURFACE ( 'NONE', #40661, 0.04999999999999991257 ) ; +#41225 = FILL_AREA_STYLE ('',( #25413 ) ) ; +#41226 = FILL_AREA_STYLE_COLOUR ( '', #100043 ) ; +#41227 = CARTESIAN_POINT ( 'NONE', ( 1.867699582579569917, -1.228633653069069798, 0.8100000000000004974 ) ) ; +#41228 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#41229 = STYLED_ITEM ( 'NONE', ( #81026 ), #19425 ) ; +#41230 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.009158714663670502E-14 ) ) ; +#41231 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #84088, 'design' ) ; +#41232 = EDGE_CURVE ( 'NONE', #43123, #72705, #95163, .T. ) ; +#41233 = ORIENTED_EDGE ( 'NONE', *, *, #38247, .T. ) ; +#41234 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999983236, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#41235 = EDGE_CURVE ( 'NONE', #65802, #96999, #1265, .T. ) ; +#41237 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57442 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69843, #54576, #18220 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41236 = FILL_AREA_STYLE_COLOUR ( '', #42803 ) ; +#41238 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38158, 'distance_accuracy_value', 'NONE'); +#41239 = VECTOR ( 'NONE', #38308, 1000.000000000000000 ) ; +#41240 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.383333333333333304, 1.747825839085088807E-76 ) ) ; +#41241 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#41242 = LINE ( 'NONE', #25928, #87899 ) ; +#41243 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91778 ) ) ; +#41244 = STYLED_ITEM ( 'NONE', ( #41995 ), #96612 ) ; +#41245 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41246 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41247 = ORIENTED_EDGE ( 'NONE', *, *, #7819, .F. ) ; +#41248 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41249 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41250 = VECTOR ( 'NONE', #14336, 1000.000000000000000 ) ; +#41251 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27456, #19786, #50952, #82090, #95097, #22280, #9776, #25706, #40002, #63513, #9279 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.017691337436076861E-05, 3.952423233967839020E-05, 5.875382848037714797E-05, 7.832621165737440217E-05, 9.793198170667220673E-05, 0.0001172428034372756123, 0.0001365502000149577608, 0.0001561259619804714234 ), + .UNSPECIFIED. ) ; +#41252 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 8.569316000000000599, 0.8648700000000000276 ) ) ; +#41253 = VECTOR ( 'NONE', #57053, 1000.000000000000000 ) ; +#41254 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#41255 = ADVANCED_FACE ( 'NONE', ( #79392 ), #9353, .T. ) ; +#41256 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19234, 'distance_accuracy_value', 'NONE'); +#41257 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37955 ), #70592 ) ; +#41258 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1356, 'distance_accuracy_value', 'NONE'); +#41259 = ORIENTED_EDGE ( 'NONE', *, *, #79198, .T. ) ; +#41260 = VERTEX_POINT ( 'NONE', #43572 ) ; +#41261 = FILL_AREA_STYLE_COLOUR ( '', #21065 ) ; +#41262 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41263 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66562 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9981, #33067, #58593 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41264 = ORIENTED_EDGE ( 'NONE', *, *, #67652, .F. ) ; +#41265 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.000000000000000000 ) ) ; +#41266 = PRESENTATION_STYLE_ASSIGNMENT (( #26440 ) ) ; +#41267 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41268 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41269 = CARTESIAN_POINT ( 'NONE', ( -1.367367192634590056, -1.017871276266119951, 0.8299999999999997380 ) ) ; +#41270 = EDGE_CURVE ( 'NONE', #31104, #83662, #33203, .T. ) ; +#41271 = PRODUCT_CONTEXT ( 'NONE', #23416, 'mechanical' ) ; +#41272 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41273 = EDGE_CURVE ( 'NONE', #47955, #51201, #35956, .T. ) ; +#41275 = ORIENTED_EDGE ( 'NONE', *, *, #79675, .T. ) ; +#41274 = EDGE_LOOP ( 'NONE', ( #60987, #11020, #78648, #48837 ) ) ; +#41276 = AXIS2_PLACEMENT_3D ( 'NONE', #92832, #77058, #61770 ) ; +#41277 = ORIENTED_EDGE ( 'NONE', *, *, #54173, .F. ) ; +#41278 = LINE ( 'NONE', #72381, #1853 ) ; +#41279 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#41280 = CARTESIAN_POINT ( 'NONE', ( 1.418698861684009938, -1.069424818316000003, 0.8100000000000000533 ) ) ; +#41281 = ORIENTED_EDGE ( 'NONE', *, *, #773, .T. ) ; +#41282 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49430 ) ) ; +#41283 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41284 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#41285 = AXIS2_PLACEMENT_3D ( 'NONE', #97654, #28744, #5727 ) ; +#41286 = ORIENTED_EDGE ( 'NONE', *, *, #37718, .T. ) ; +#41287 = ORIENTED_EDGE ( 'NONE', *, *, #24340, .F. ) ; +#41289 = PRESENTATION_STYLE_ASSIGNMENT (( #1470 ) ) ; +#41288 = FACE_OUTER_BOUND ( 'NONE', #42260, .T. ) ; +#41290 = AXIS2_PLACEMENT_3D ( 'NONE', #70263, #8396, #314 ) ; +#41291 = ORIENTED_EDGE ( 'NONE', *, *, #99480, .F. ) ; +#41292 = STYLED_ITEM ( 'NONE', ( #24435 ), #25867 ) ; +#41293 = EDGE_LOOP ( 'NONE', ( #39326, #51592, #9202, #45573 ) ) ; +#41294 = FACE_OUTER_BOUND ( 'NONE', #60492, .T. ) ; +#41295 = EDGE_CURVE ( 'NONE', #90342, #77797, #67065, .T. ) ; +#41296 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#41297 = AXIS2_PLACEMENT_3D ( 'NONE', #88512, #66036, #19565 ) ; +#41299 = ORIENTED_EDGE ( 'NONE', *, *, #66998, .T. ) ; +#41298 = FILL_AREA_STYLE ('',( #10524 ) ) ; +#41300 = PRESENTATION_STYLE_ASSIGNMENT (( #34648 ) ) ; +#41301 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41302 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#41303 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#41304 = VERTEX_POINT ( 'NONE', #12870 ) ; +#41305 = SURFACE_STYLE_USAGE ( .BOTH. , #96883 ) ; +#41306 = FACE_OUTER_BOUND ( 'NONE', #49181, .T. ) ; +#41307 = ORIENTED_EDGE ( 'NONE', *, *, #64172, .F. ) ; +#41308 = ORIENTED_EDGE ( 'NONE', *, *, #33946, .T. ) ; +#41309 = VECTOR ( 'NONE', #22642, 1000.000000000000000 ) ; +#41310 = EDGE_CURVE ( 'NONE', #80892, #13371, #28282, .T. ) ; +#41312 = FILL_AREA_STYLE_COLOUR ( '', #74788 ) ; +#41311 = SURFACE_SIDE_STYLE ('',( #86744 ) ) ; +#41313 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.8500000000070031536, 0.6499230723533214737 ) ) ; +#41314 = PRESENTATION_STYLE_ASSIGNMENT (( #25998 ) ) ; +#41315 = CARTESIAN_POINT ( 'NONE', ( -0.3666263778268459839, -1.099567016183110146, 0.8299999999999999600 ) ) ; +#41316 = EDGE_CURVE ( 'NONE', #8845, #31070, #12365, .T. ) ; +#41317 = LINE ( 'NONE', #88272, #46130 ) ; +#41318 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28253 ), #73955 ) ; +#41319 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#41320 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41321 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41322 = ORIENTED_EDGE ( 'NONE', *, *, #46462, .F. ) ; +#41323 = CARTESIAN_POINT ( 'NONE', ( 0.3664728319017789837, -1.220832247304010298, 0.8100000000000000533 ) ) ; +#41324 = ORIENTED_EDGE ( 'NONE', *, *, #52987, .F. ) ; +#41325 = EDGE_CURVE ( 'NONE', #25468, #42036, #87991, .T. ) ; +#41326 = CIRCLE ( 'NONE', #52751, 0.1099999999999998479 ) ; +#41327 = CARTESIAN_POINT ( 'NONE', ( 5.264745124874999682, 5.557041124875000904, 0.8991599999999999593 ) ) ; +#41328 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41329 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#41330 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41331 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39696 ), #21758 ) ; +#41332 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#41333 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41334 = PRESENTATION_STYLE_ASSIGNMENT (( #64788 ) ) ; +#41335 = FACE_OUTER_BOUND ( 'NONE', #71026, .T. ) ; +#41336 = DIRECTION ( 'NONE', ( -0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#41337 = AXIS2_PLACEMENT_3D ( 'NONE', #69704, #23787, #54941 ) ; +#41338 = FACE_OUTER_BOUND ( 'NONE', #20399, .T. ) ; +#41339 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#41340 = EDGE_CURVE ( 'NONE', #21531, #82682, #11359, .T. ) ; +#41341 = VECTOR ( 'NONE', #24833, 1000.000000000000000 ) ; +#41342 = FACE_OUTER_BOUND ( 'NONE', #65484, .T. ) ; +#41343 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#41344 = SURFACE_STYLE_FILL_AREA ( #86265 ) ; +#41345 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41346 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000000971, 0.2400000000000000189 ) ) ; +#41347 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 9.949999999999999289, 0.000000000000000000 ) ) ; +#41348 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73515, 'distance_accuracy_value', 'NONE'); +#41349 = VERTEX_POINT ( 'NONE', #50293 ) ; +#41350 = SURFACE_STYLE_FILL_AREA ( #34206 ) ; +#41351 = EDGE_CURVE ( 'NONE', #75920, #68705, #82907, .T. ) ; +#41352 = EDGE_LOOP ( 'NONE', ( #98447, #76798, #20300, #98937 ) ) ; +#41353 = EDGE_CURVE ( 'NONE', #89849, #19927, #66563, .T. ) ; +#41354 = SURFACE_STYLE_FILL_AREA ( #95932 ) ; +#41355 = LINE ( 'NONE', #25538, #80190 ) ; +#41356 = CARTESIAN_POINT ( 'NONE', ( 1.705268638847220242, -0.9625006208768249749, 0.8100000000000006084 ) ) ; +#41357 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16808 ) ) ; +#41358 = CARTESIAN_POINT ( 'NONE', ( 1.323820061220085220, 3.099999999999970335, 0.000000000000000000 ) ) ; +#41359 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #849, #32005, #99808, #63171, #52989, #84110, #37658, #92254 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000006106, 0.5000000000000012212, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#41360 = ORIENTED_EDGE ( 'NONE', *, *, #73030, .F. ) ; +#41361 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82183 ), #38145 ) ; +#41362 = ORIENTED_EDGE ( 'NONE', *, *, #3367, .F. ) ; +#41363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41364 = LINE ( 'NONE', #26548, #30276 ) ; +#41365 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#41366 = ADVANCED_FACE ( 'NONE', ( #65558 ), #58955, .T. ) ; +#41367 = SURFACE_STYLE_USAGE ( .BOTH. , #11120 ) ; +#41368 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#41369 = CIRCLE ( 'NONE', #29890, 0.009999999999999998473 ) ; +#41370 = SURFACE_STYLE_USAGE ( .BOTH. , #41870 ) ; +#41371 = ORIENTED_EDGE ( 'NONE', *, *, #20902, .F. ) ; +#41372 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41373 = VERTEX_POINT ( 'NONE', #46050 ) ; +#41374 = EDGE_CURVE ( 'NONE', #51787, #97408, #99128, .T. ) ; +#41376 = VECTOR ( 'NONE', #43675, 1000.000000000000000 ) ; +#41375 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41377 = AXIS2_PLACEMENT_3D ( 'NONE', #81650, #17304, #40827 ) ; +#41378 = AXIS2_PLACEMENT_3D ( 'NONE', #88043, #24781, #18052 ) ; +#41379 = SURFACE_STYLE_USAGE ( .BOTH. , #80189 ) ; +#41380 = ORIENTED_EDGE ( 'NONE', *, *, #36684, .F. ) ; +#41381 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41382 = STYLED_ITEM ( 'NONE', ( #48365 ), #60844 ) ; +#41383 = FILL_AREA_STYLE_COLOUR ( '', #55066 ) ; +#41384 = PRESENTATION_STYLE_ASSIGNMENT (( #11134 ) ) ; +#41385 = VECTOR ( 'NONE', #41381, 1000.000000000000000 ) ; +#41386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15803 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66106, #42130, #25810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41388 = SURFACE_SIDE_STYLE ('',( #73018 ) ) ; +#41389 = EDGE_CURVE ( 'NONE', #1626, #41604, #17546, .T. ) ; +#41390 = DIRECTION ( 'NONE', ( 0.7071067811865470176, -0.7071067811865480168, 0.000000000000000000 ) ) ; +#41391 = PRESENTATION_STYLE_ASSIGNMENT (( #10118 ) ) ; +#41392 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#41393 = ADVANCED_FACE ( 'NONE', ( #84395 ), #93013, .T. ) ; +#41395 = VERTEX_POINT ( 'NONE', #54274 ) ; +#41394 = ORIENTED_EDGE ( 'NONE', *, *, #38606, .T. ) ; +#41396 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41397 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10296 ) ) ; +#41398 = ORIENTED_EDGE ( 'NONE', *, *, #15224, .F. ) ; +#41399 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, -0.02000000000002305142 ) ) ; +#41400 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85381 ) ) ; +#41401 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8648700000000000276 ) ) ; +#41402 = ORIENTED_EDGE ( 'NONE', *, *, #40136, .F. ) ; +#41403 = ORIENTED_EDGE ( 'NONE', *, *, #9592, .T. ) ; +#41404 = CARTESIAN_POINT ( 'NONE', ( -4.720018080210465332E-17, 0.2500000001077752887, -1.665334536835250932E-17 ) ) ; +#41405 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41406 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#41407 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57687 ) ) ; +#41409 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#41408 = LINE ( 'NONE', #50584, #23699 ) ; +#41410 = VERTEX_POINT ( 'NONE', #38943 ) ; +#41411 = VERTEX_POINT ( 'NONE', #45058 ) ; +#41412 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41413 = VERTEX_POINT ( 'NONE', #68555 ) ; +#41414 = ADVANCED_FACE ( 'NONE', ( #85396 ), #6221, .F. ) ; +#41415 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41417 = VERTEX_POINT ( 'NONE', #41474 ) ; +#41416 = FACE_OUTER_BOUND ( 'NONE', #66636, .T. ) ; +#41418 = PLANE ( 'NONE', #95474 ) ; +#41419 = PLANE ( 'NONE', #17824 ) ; +#41420 = STYLED_ITEM ( 'NONE', ( #13275 ), #53396 ) ; +#41421 = VERTEX_POINT ( 'NONE', #64946 ) ; +#41422 = CARTESIAN_POINT ( 'NONE', ( -0.05957252635663159990, -1.226312279485590073, 0.8299999999999999600 ) ) ; +#41423 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41424 = ORIENTED_EDGE ( 'NONE', *, *, #11167, .T. ) ; +#41425 = EDGE_CURVE ( 'NONE', #82970, #84669, #71097, .T. ) ; +#41426 = FACE_OUTER_BOUND ( 'NONE', #96253, .T. ) ; +#41427 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85418 ) ) ; +#41428 = SURFACE_STYLE_USAGE ( .BOTH. , #95497 ) ; +#41429 = CARTESIAN_POINT ( 'NONE', ( -1.346516121155820089, -1.141526082476290060, 0.8300000000000000711 ) ) ; +#41430 = ADVANCED_FACE ( 'NONE', ( #94018 ), #72111, .F. ) ; +#41431 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59389 ), #54471 ) ; +#41432 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41433 = SURFACE_STYLE_FILL_AREA ( #63902 ) ; +#41434 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41435 = CARTESIAN_POINT ( 'NONE', ( 1.608893861054889962, -1.000931601726380071, 0.8299999999999990719 ) ) ; +#41436 = VERTEX_POINT ( 'NONE', #25171 ) ; +#41437 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17589 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12971, #27376, #3874 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41438 = CARTESIAN_POINT ( 'NONE', ( -1.000023319491960105, -0.9315058289328710384, 0.8300000000000000711 ) ) ; +#41439 = ORIENTED_EDGE ( 'NONE', *, *, #44625, .T. ) ; +#41440 = EDGE_CURVE ( 'NONE', #43863, #9393, #17445, .T. ) ; +#41441 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41442 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#41443 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#41445 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41444 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#41447 = VECTOR ( 'NONE', #97665, 1000.000000000000000 ) ; +#41446 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#41448 = LINE ( 'NONE', #594, #54891 ) ; +#41449 = FILL_AREA_STYLE ('',( #57802 ) ) ; +#41450 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28387 ) ) ; +#41451 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #37741, #12284, #68838, #38242 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#41452 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41453 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#41454 = SURFACE_STYLE_USAGE ( .BOTH. , #35821 ) ; +#41455 = ADVANCED_FACE ( 'NONE', ( #24154 ), #86416, .T. ) ; +#41456 = ORIENTED_EDGE ( 'NONE', *, *, #90796, .F. ) ; +#41457 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41458 = STYLED_ITEM ( 'NONE', ( #35761 ), #2893 ) ; +#41459 = PLANE ( 'NONE', #78247 ) ; +#41460 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#41461 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85454 ), #82279 ) ; +#41462 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3549, 'distance_accuracy_value', 'NONE'); +#41463 = ORIENTED_EDGE ( 'NONE', *, *, #25339, .T. ) ; +#41464 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#41465 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#41466 = CARTESIAN_POINT ( 'NONE', ( -1.077884384038320098, -0.9706035140527139449, 0.8299999999999999600 ) ) ; +#41467 = FACE_OUTER_BOUND ( 'NONE', #36992, .T. ) ; +#41468 = EDGE_CURVE ( 'NONE', #98596, #7367, #13574, .T. ) ; +#41469 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.05000000000000002359, 0.2100000000000000200 ) ) ; +#41470 = FILL_AREA_STYLE ('',( #49639 ) ) ; +#41471 = STYLED_ITEM ( 'NONE', ( #72498 ), #67719 ) ; +#41472 = SURFACE_SIDE_STYLE ('',( #57306 ) ) ; +#41473 = CARTESIAN_POINT ( 'NONE', ( -0.9926480063939780996, -1.365766081162230083, 0.8300000000000001821 ) ) ; +#41474 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.300000000000000711, 0.000000000000000000 ) ) ; +#41475 = ORIENTED_EDGE ( 'NONE', *, *, #74256, .F. ) ; +#41476 = FILL_AREA_STYLE_COLOUR ( '', #53089 ) ; +#41477 = AXIS2_PLACEMENT_3D ( 'NONE', #55012, #30991, #62673 ) ; +#41478 = VERTEX_POINT ( 'NONE', #63470 ) ; +#41479 = FACE_OUTER_BOUND ( 'NONE', #31608, .T. ) ; +#41480 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38502, 'distance_accuracy_value', 'NONE'); +#41481 = PLANE ( 'NONE', #12913 ) ; +#41482 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41483 = CARTESIAN_POINT ( 'NONE', ( -0.2109871940610940078, -1.020192282374009940, 0.8100000000000000533 ) ) ; +#41484 = FILL_AREA_STYLE_COLOUR ( '', #26519 ) ; +#41485 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#41486 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.000000000000000000 ) ) ; +#41487 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5910 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37855, #85818, #85304 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41488 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#41489 = SURFACE_SIDE_STYLE ('',( #2684 ) ) ; +#41490 = ORIENTED_EDGE ( 'NONE', *, *, #34689, .F. ) ; +#41491 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41492 = FILL_AREA_STYLE ('',( #75750 ) ) ; +#41493 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#41494 = ORIENTED_EDGE ( 'NONE', *, *, #19679, .T. ) ; +#41495 = FACE_OUTER_BOUND ( 'NONE', #8038, .T. ) ; +#41496 = SURFACE_STYLE_FILL_AREA ( #71633 ) ; +#41497 = FILL_AREA_STYLE_COLOUR ( '', #41958 ) ; +#41498 = ORIENTED_EDGE ( 'NONE', *, *, #76129, .T. ) ; +#41499 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21871 ), #38205 ) ; +#41500 = CARTESIAN_POINT ( 'NONE', ( -0.8360056965048459077, 1.033342884875539713, 0.8100000000000001643 ) ) ; +#41501 = LINE ( 'NONE', #80311, #50801 ) ; +#41502 = LINE ( 'NONE', #34368, #70800 ) ; +#41503 = EDGE_CURVE ( 'NONE', #79048, #78820, #10211, .T. ) ; +#41504 = ORIENTED_EDGE ( 'NONE', *, *, #82499, .F. ) ; +#41505 = LINE ( 'NONE', #62992, #71858 ) ; +#41506 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#41507 = ORIENTED_EDGE ( 'NONE', *, *, #21858, .F. ) ; +#41508 = STYLED_ITEM ( 'NONE', ( #69246 ), #28427 ) ; +#41509 = VECTOR ( 'NONE', #36080, 1000.000000000000000 ) ; +#41510 = EDGE_CURVE ( 'NONE', #33079, #66631, #73613, .T. ) ; +#41511 = AXIS2_PLACEMENT_3D ( 'NONE', #29274, #13890, #45537 ) ; +#41512 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41513 = ORIENTED_EDGE ( 'NONE', *, *, #3288, .T. ) ; +#41515 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80588 ), #72464 ) ; +#41514 = FILL_AREA_STYLE ('',( #10249 ) ) ; +#41516 = FILL_AREA_STYLE_COLOUR ( '', #775 ) ; +#41517 = STYLED_ITEM ( 'NONE', ( #99836 ), #98443 ) ; +#41518 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41519 = LINE ( 'NONE', #86969, #16137 ) ; +#41520 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41522 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#41521 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41523 = ORIENTED_EDGE ( 'NONE', *, *, #95014, .T. ) ; +#41525 = ORIENTED_EDGE ( 'NONE', *, *, #60898, .F. ) ; +#41524 = EDGE_LOOP ( 'NONE', ( #65209, #66727, #60827, #49440 ) ) ; +#41526 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41527 = VERTEX_POINT ( 'NONE', #58836 ) ; +#41528 = EDGE_CURVE ( 'NONE', #49432, #22475, #65432, .T. ) ; +#41529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4046 ) ) ; +#41530 = ORIENTED_EDGE ( 'NONE', *, *, #77602, .T. ) ; +#41532 = ORIENTED_EDGE ( 'NONE', *, *, #99741, .T. ) ; +#41531 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41533 = VECTOR ( 'NONE', #54102, 1000.000000000000000 ) ; +#41534 = PLANE ( 'NONE', #28004 ) ; +#41535 = EDGE_LOOP ( 'NONE', ( #35755, #30826, #52174, #36965, #70003, #53740 ) ) ; +#41536 = PLANE ( 'NONE', #97733 ) ; +#41537 = FILL_AREA_STYLE_COLOUR ( '', #82625 ) ; +#41538 = FILL_AREA_STYLE ('',( #10276 ) ) ; +#41539 = ORIENTED_EDGE ( 'NONE', *, *, #28787, .F. ) ; +#41540 = EDGE_CURVE ( 'NONE', #60190, #23574, #27677, .T. ) ; +#41541 = FACE_OUTER_BOUND ( 'NONE', #76961, .T. ) ; +#41542 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41543 = LINE ( 'NONE', #95619, #33697 ) ; +#41544 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49139 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100379, #40126, #13666 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41545 = ORIENTED_EDGE ( 'NONE', *, *, #58156, .F. ) ; +#41546 = SURFACE_SIDE_STYLE ('',( #80356 ) ) ; +#41547 = VECTOR ( 'NONE', #23698, 1000.000000000000000 ) ; +#41548 = CARTESIAN_POINT ( 'NONE', ( 0.06941959667897069919, -1.084027901463999966, 0.8300000000000002931 ) ) ; +#41550 = FACE_OUTER_BOUND ( 'NONE', #78153, .T. ) ; +#41549 = FILL_AREA_STYLE_COLOUR ( '', #2331 ) ; +#41551 = CARTESIAN_POINT ( 'NONE', ( -0.9128876696368980470, 0.4958735128372510625, 0.8299999999999999600 ) ) ; +#41552 = FACE_OUTER_BOUND ( 'NONE', #91844, .T. ) ; +#41553 = SURFACE_STYLE_FILL_AREA ( #71681 ) ; +#41554 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90430 ), #66031 ) ; +#41555 = EDGE_CURVE ( 'NONE', #96887, #51626, #93883, .T. ) ; +#41556 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4078 ), #74198 ) ; +#41557 = SURFACE_STYLE_FILL_AREA ( #65031 ) ; +#41558 = ADVANCED_FACE ( 'NONE', ( #3162 ), #58330, .T. ) ; +#41559 = FILL_AREA_STYLE ('',( #94112 ) ) ; +#41560 = PLANE ( 'NONE', #56814 ) ; +#41561 = PLANE ( 'NONE', #46351 ) ; +#41562 = AXIS2_PLACEMENT_3D ( 'NONE', #79190, #31207, #47024 ) ; +#41563 = CARTESIAN_POINT ( 'NONE', ( 0.9823626554959720147, -1.038425069758839969, 0.8100000000000000533 ) ) ; +#41564 = ORIENTED_EDGE ( 'NONE', *, *, #65949, .T. ) ; +#41566 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41565 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41567 = EDGE_CURVE ( 'NONE', #92405, #15626, #97058, .T. ) ; +#41568 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#41569 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2999999999999999889, -13.54999999999999893 ) ) ; +#41570 = EDGE_CURVE ( 'NONE', #5244, #34152, #34336, .T. ) ; +#41571 = FILL_AREA_STYLE_COLOUR ( '', #33688 ) ; +#41572 = ORIENTED_EDGE ( 'NONE', *, *, #71949, .T. ) ; +#41573 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41574 = FILL_AREA_STYLE_COLOUR ( '', #15472 ) ; +#41575 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41576 = SURFACE_SIDE_STYLE ('',( #88530 ) ) ; +#41577 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#41578 = EDGE_CURVE ( 'NONE', #1547, #38419, #49646, .T. ) ; +#41580 = EDGE_CURVE ( 'NONE', #57703, #60190, #67438, .T. ) ; +#41579 = CARTESIAN_POINT ( 'NONE', ( 0.2346921643439940086, -1.433080367293090074, 0.8100000000000000533 ) ) ; +#41581 = VECTOR ( 'NONE', #55307, 1000.000000000000000 ) ; +#41582 = DIRECTION ( 'NONE', ( 2.145240645824569941E-26, -6.286240788502049877E-13, 1.000000000000000000 ) ) ; +#41583 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41584 = ORIENTED_EDGE ( 'NONE', *, *, #43620, .T. ) ; +#41585 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41586 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#41589 = VECTOR ( 'NONE', #32637, 1000.000000000000000 ) ; +#41588 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41587 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#41590 = PLANE ( 'NONE', #5220 ) ; +#41591 = ADVANCED_FACE ( 'NONE', ( #26164 ), #51151, .F. ) ; +#41592 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41593 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41594 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41595 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#41596 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41597 = EDGE_CURVE ( 'NONE', #93205, #26148, #14277, .T. ) ; +#41598 = AXIS2_PLACEMENT_3D ( 'NONE', #39044, #24252, #55897 ) ; +#41599 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41600 = SURFACE_SIDE_STYLE ('',( #97668 ) ) ; +#41601 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#41602 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#41603 = LINE ( 'NONE', #71216, #82877 ) ; +#41604 = VERTEX_POINT ( 'NONE', #86155 ) ; +#41605 = VERTEX_POINT ( 'NONE', #45428 ) ; +#41606 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85593 ), #5673 ) ; +#41607 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#41608 = LINE ( 'NONE', #8340, #57651 ) ; +#41609 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35134 ) ) ; +#41610 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8991599999999999593 ) ) ; +#41611 = CARTESIAN_POINT ( 'NONE', ( 1.870562122921110015, -1.007076035477679987, 0.8299999999999999600 ) ) ; +#41612 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#41613 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#41614 = SURFACE_STYLE_FILL_AREA ( #19103 ) ; +#41615 = ORIENTED_EDGE ( 'NONE', *, *, #49798, .F. ) ; +#41616 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41617 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#41618 = ORIENTED_EDGE ( 'NONE', *, *, #70774, .F. ) ; +#41619 = CARTESIAN_POINT ( 'NONE', ( 6.325405999999999196, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#41620 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25311 ) ) ; +#41621 = PLANE ( 'NONE', #93379 ) ; +#41622 = CIRCLE ( 'NONE', #51400, 0.009999999999999998473 ) ; +#41623 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#41624 = VECTOR ( 'NONE', #22539, 1000.000000000000000 ) ; +#41625 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41626 = EDGE_CURVE ( 'NONE', #39129, #95604, #44935, .T. ) ; +#41627 = ORIENTED_EDGE ( 'NONE', *, *, #65400, .T. ) ; +#41628 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41629 = FILL_AREA_STYLE ('',( #94701 ) ) ; +#41630 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50967, 'distance_accuracy_value', 'NONE'); +#41631 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41632 = VECTOR ( 'NONE', #6709, 1000.000000000000000 ) ; +#41633 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8944 ), #67680 ) ; +#41634 = EDGE_CURVE ( 'NONE', #16500, #51935, #39705, .T. ) ; +#41635 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41636 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85852 ), #87467 ) ; +#41637 = VERTEX_POINT ( 'NONE', #6100 ) ; +#41638 = VECTOR ( 'NONE', #66866, 1000.000000000000000 ) ; +#41639 = AXIS2_PLACEMENT_3D ( 'NONE', #2284, #64064, #1253 ) ; +#41640 = FACE_OUTER_BOUND ( 'NONE', #78945, .T. ) ; +#41641 = DIRECTION ( 'NONE', ( 1.291173436397889936E-79, -1.000000000000000000, 5.992048669697412538E-127 ) ) ; +#41642 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41643 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41644 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35171 ) ) ; +#41645 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75874 ), #10543 ) ; +#41646 = AXIS2_PLACEMENT_3D ( 'NONE', #13832, #45008, #76181 ) ; +#41647 = SURFACE_SIDE_STYLE ('',( #64610 ) ) ; +#41648 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #25862, #2875 ), + ( #88140, #72291 ), + ( #49329, #34028 ), + ( #73326, #80477 ), + ( #18657, #89138 ), + ( #25371, #17650 ), + ( #79987, #19168 ), + ( #18139, #9918 ), + ( #56002, #10408 ), + ( #65144, #1351 ), + ( #96262, #34538 ), + ( #33523, #42676 ), + ( #26362, #57517 ), + ( #10936, #32510 ), + ( #52843, #51852 ), + ( #81994, #5324 ), + ( #67626, #67141 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07361161809163040137, 0.1418704760126159869, 0.2047010881220309997, 0.2650638462607379786, 0.3226075809791700277, 0.3798957495557009900, 0.4370254124446700250, 0.4956449832836989922, 0.5547100597432720326, 0.6152773224479549663, 0.6777605979153460414, 0.7425370015046289796, 0.8723910695608629862, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#41649 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #86081, #82894 ) ; +#41650 = VECTOR ( 'NONE', #38373, 1000.000000000000000 ) ; +#41651 = VERTEX_POINT ( 'NONE', #37339 ) ; +#41653 = ORIENTED_EDGE ( 'NONE', *, *, #27837, .T. ) ; +#41652 = PRESENTATION_STYLE_ASSIGNMENT (( #72273 ) ) ; +#41655 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18282 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25652, #41983, #88428 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41654 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8381, 'distance_accuracy_value', 'NONE'); +#41656 = LINE ( 'NONE', #56499, #21542 ) ; +#41657 = FILL_AREA_STYLE ('',( #64622 ) ) ; +#41658 = VECTOR ( 'NONE', #69824, 1000.000000000000000 ) ; +#41659 = SURFACE_STYLE_USAGE ( .BOTH. , #65620 ) ; +#41660 = ORIENTED_EDGE ( 'NONE', *, *, #51203, .F. ) ; +#41661 = EDGE_CURVE ( 'NONE', #18396, #79602, #92417, .T. ) ; +#41662 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#41663 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41664 = STYLED_ITEM ( 'NONE', ( #44165 ), #27626 ) ; +#41665 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41666 = ORIENTED_EDGE ( 'NONE', *, *, #12631, .F. ) ; +#41668 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#41667 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000971, 0.2500000000000000000 ) ) ; +#41669 = ORIENTED_EDGE ( 'NONE', *, *, #79025, .T. ) ; +#41670 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41671 = ORIENTED_EDGE ( 'NONE', *, *, #11716, .T. ) ; +#41672 = CARTESIAN_POINT ( 'NONE', ( 0.9823498513717580094, -1.085342039781126200, 0.8099999999999361044 ) ) ; +#41674 = LINE ( 'NONE', #72806, #38515 ) ; +#41673 = PLANE ( 'NONE', #5464 ) ; +#41675 = EDGE_LOOP ( 'NONE', ( #25958, #68237, #73451, #86882, #32626, #72801 ) ) ; +#41676 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94782 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85959, #15990, #61501 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41677 = PLANE ( 'NONE', #92327 ) ; +#41678 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46733 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93046, #1700, #85931 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41679 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41680 = ORIENTED_EDGE ( 'NONE', *, *, #11307, .F. ) ; +#41681 = DIRECTION ( 'NONE', ( -3.880665108489179890E-39, 1.000000000000000000, 2.469472024280190074E-26 ) ) ; +#41682 = ORIENTED_EDGE ( 'NONE', *, *, #79575, .F. ) ; +#41683 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41684 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#41685 = CARTESIAN_POINT ( 'NONE', ( -1.024943210826370299, -1.268071887441960088, 0.8299999999999999600 ) ) ; +#41686 = STYLED_ITEM ( 'NONE', ( #22029 ), #68450 ) ; +#41687 = FILL_AREA_STYLE ('',( #64655 ) ) ; +#41688 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #924 ) ) ; +#41689 = CARTESIAN_POINT ( 'NONE', ( -0.4333333333333340143, 3.500000000000000000, 0.000000000000000000 ) ) ; +#41690 = LINE ( 'NONE', #57531, #60570 ) ; +#41691 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41692 = CARTESIAN_POINT ( 'NONE', ( 1.296768031029680079, -0.9834456900322131601, 0.8100000000000000533 ) ) ; +#41693 = ORIENTED_EDGE ( 'NONE', *, *, #47928, .T. ) ; +#41695 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72462 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43916, #83241, #36770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41694 = PRESENTATION_STYLE_ASSIGNMENT (( #81014 ) ) ; +#41696 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9121, 'distance_accuracy_value', 'NONE'); +#41697 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8991599999999999593 ) ) ; +#41699 = EDGE_CURVE ( 'NONE', #95207, #23664, #68434, .T. ) ; +#41698 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41700 = VECTOR ( 'NONE', #92243, 1000.000000000000000 ) ; +#41701 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77779 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17455, #70073, #16952 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41702 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41703 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -2.122145052278295409E-17, 0.4000000000000000222 ) ) ; +#41704 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#41705 = SURFACE_SIDE_STYLE ('',( #40704 ) ) ; +#41706 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#41707 = ORIENTED_EDGE ( 'NONE', *, *, #256, .F. ) ; +#41708 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60493, #13943, #68601 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41709 = FILL_AREA_STYLE_COLOUR ( '', #14533 ) ; +#41710 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#41711 = VECTOR ( 'NONE', #96865, 1000.000000000000000 ) ; +#41712 = FILL_AREA_STYLE_COLOUR ( '', #712 ) ; +#41713 = FILL_AREA_STYLE_COLOUR ( '', #75535 ) ; +#41714 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41715 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#41716 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#41717 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41718 = EDGE_CURVE ( 'NONE', #60860, #55685, #86677, .T. ) ; +#41719 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41720 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41721 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.5000000000000000000, -13.54999999999999893 ) ) ; +#41722 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#41723 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.600000000000000089, -0.2000000000000000111 ) ) ; +#41724 = CARTESIAN_POINT ( 'NONE', ( 1.859836464378280096, -1.220010286732279958, 0.8100000000000004974 ) ) ; +#41725 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41727 = VECTOR ( 'NONE', #75136, 1000.000000000000000 ) ; +#41726 = PLANE ( 'NONE', #15197 ) ; +#41728 = CARTESIAN_POINT ( 'NONE', ( -0.1725832855250629960, -0.9074576374047380600, 0.8300000000000009592 ) ) ; +#41729 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41730 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41731 = EDGE_LOOP ( 'NONE', ( #43747, #6932, #24095, #79183 ) ) ; +#41732 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41733 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41734 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41736 = FACE_OUTER_BOUND ( 'NONE', #31881, .T. ) ; +#41735 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41737 = LINE ( 'NONE', #48415, #30814 ) ; +#41738 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87850, #10137, #72520 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41739 = LINE ( 'NONE', #3920, #73826 ) ; +#41740 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41741 = ADVANCED_FACE ( 'NONE', ( #91436 ), #40229, .F. ) ; +#41742 = ORIENTED_EDGE ( 'NONE', *, *, #99212, .T. ) ; +#41743 = PLANE ( 'NONE', #7954 ) ; +#41744 = SURFACE_STYLE_FILL_AREA ( #10473 ) ; +#41745 = LINE ( 'NONE', #64217, #75801 ) ; +#41746 = PRESENTATION_STYLE_ASSIGNMENT (( #58102 ) ) ; +#41747 = EDGE_CURVE ( 'NONE', #87607, #8523, #68920, .T. ) ; +#41748 = VERTEX_POINT ( 'NONE', #99987 ) ; +#41749 = ORIENTED_EDGE ( 'NONE', *, *, #38084, .F. ) ; +#41750 = FILL_AREA_STYLE_COLOUR ( '', #29225 ) ; +#41751 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#41752 = ORIENTED_EDGE ( 'NONE', *, *, #8397, .F. ) ; +#41753 = CARTESIAN_POINT ( 'NONE', ( 0.3500290314248439838, -0.9624968822990390693, 0.8299999999999996270 ) ) ; +#41754 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41755 = PRESENTATION_STYLE_ASSIGNMENT (( #92330 ) ) ; +#41756 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999870064 ) ) ; +#41757 = PRODUCT_CONTEXT ( 'NONE', #37146, 'mechanical' ) ; +#41758 = CARTESIAN_POINT ( 'NONE', ( -0.9238200612200850870, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#41759 = SURFACE_STYLE_USAGE ( .BOTH. , #10497 ) ; +#41760 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#41762 = VERTEX_POINT ( 'NONE', #16187 ) ; +#41761 = EDGE_LOOP ( 'NONE', ( #88347, #44297, #97742, #30290 ) ) ; +#41763 = VERTEX_POINT ( 'NONE', #904 ) ; +#41764 = ORIENTED_EDGE ( 'NONE', *, *, #19658, .T. ) ; +#41765 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33849, #96585, #88450, #71637 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#41766 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41767 = VECTOR ( 'NONE', #70661, 1000.000000000000114 ) ; +#41768 = VECTOR ( 'NONE', #64331, 1000.000000000000000 ) ; +#41769 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7698, 'distance_accuracy_value', 'NONE'); +#41770 = STYLED_ITEM ( 'NONE', ( #15791 ), #54587 ) ; +#41771 = CARTESIAN_POINT ( 'NONE', ( 1.840728708308519979, -1.463352833475739967, 0.8100000000000000533 ) ) ; +#41772 = CARTESIAN_POINT ( 'NONE', ( 0.5312032056918729594, -0.9984395139652609830, 0.8100000000000000533 ) ) ; +#41773 = ORIENTED_EDGE ( 'NONE', *, *, #22773, .T. ) ; +#41774 = AXIS2_PLACEMENT_3D ( 'NONE', #50711, #64997, #35398 ) ; +#41775 = ADVANCED_FACE ( 'NONE', ( #32055 ), #63222, .F. ) ; +#41776 = PLANE ( 'NONE', #67769 ) ; +#41777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17254 ), #80940 ) ; +#41778 = EDGE_LOOP ( 'NONE', ( #57452, #88388, #93956, #31285 ) ) ; +#41779 = LINE ( 'NONE', #26463, #41711 ) ; +#41780 = ORIENTED_EDGE ( 'NONE', *, *, #74337, .T. ) ; +#41781 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41783 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#41782 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.699999999999999734, 0.1829999999999999960 ) ) ; +#41784 = ADVANCED_FACE ( 'NONE', ( #41736 ), #81057, .F. ) ; +#41785 = VERTEX_POINT ( 'NONE', #34594 ) ; +#41786 = ORIENTED_EDGE ( 'NONE', *, *, #16502, .T. ) ; +#41787 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#41788 = VECTOR ( 'NONE', #76919, 1000.000000000000114 ) ; +#41789 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72762 ), #10710 ) ; +#41790 = DIRECTION ( 'NONE', ( -0.7071072811858630791, -0.7071062811868784603, 0.000000000000000000 ) ) ; +#41792 = ORIENTED_EDGE ( 'NONE', *, *, #27849, .F. ) ; +#41791 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41793 = LINE ( 'NONE', #9041, #92255 ) ; +#41794 = ORIENTED_EDGE ( 'NONE', *, *, #69457, .T. ) ; +#41795 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#41796 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#41797 = ORIENTED_EDGE ( 'NONE', *, *, #3158, .F. ) ; +#41798 = FILL_AREA_STYLE_COLOUR ( '', #28632 ) ; +#41799 = CARTESIAN_POINT ( 'NONE', ( 0.09346250786341020467, -1.325441991778449902, 0.8299999999999999600 ) ) ; +#41800 = ORIENTED_EDGE ( 'NONE', *, *, #64221, .T. ) ; +#41801 = VERTEX_POINT ( 'NONE', #81571 ) ; +#41802 = EDGE_CURVE ( 'NONE', #44510, #14577, #87682, .T. ) ; +#41803 = CARTESIAN_POINT ( 'NONE', ( 1.429289321881345165, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#41804 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41805 = STYLED_ITEM ( 'NONE', ( #1508 ), #39563 ) ; +#41806 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41807 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41808 = CARTESIAN_POINT ( 'NONE', ( -1.260684207206377305, -1.116213578446475729, 0.8099999999999024647 ) ) ; +#41809 = PLANE ( 'NONE', #54342 ) ; +#41810 = VECTOR ( 'NONE', #75495, 1000.000000000000000 ) ; +#41811 = FACE_OUTER_BOUND ( 'NONE', #93451, .T. ) ; +#41812 = FILL_AREA_STYLE_COLOUR ( '', #40703 ) ; +#41813 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32616, 'distance_accuracy_value', 'NONE'); +#41814 = ORIENTED_EDGE ( 'NONE', *, *, #80875, .T. ) ; +#41815 = CARTESIAN_POINT ( 'NONE', ( 0.01105796065628599986, -1.194792006717259936, 0.8100000000000000533 ) ) ; +#41816 = VERTEX_POINT ( 'NONE', #26416 ) ; +#41817 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41818 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#41819 = SURFACE_STYLE_FILL_AREA ( #72951 ) ; +#41820 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41823 = EDGE_CURVE ( 'NONE', #80171, #82982, #6204, .T. ) ; +#41822 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64952 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25827, #56984, #88101 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41821 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#41824 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41825 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#41826 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41827 = ORIENTED_EDGE ( 'NONE', *, *, #72760, .F. ) ; +#41828 = SURFACE_SIDE_STYLE ('',( #71960 ) ) ; +#41829 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41830 = CARTESIAN_POINT ( 'NONE', ( -1.287544264014619966, -1.018544155089240011, 0.8299999999999998490 ) ) ; +#41831 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.299999999999999822, 0.1829999999999500082 ) ) ; +#41832 = CARTESIAN_POINT ( 'NONE', ( 1.238847462264157429, -1.515052199391658139, 0.8099999999996660982 ) ) ; +#41833 = FILL_AREA_STYLE ('',( #3022 ) ) ; +#41834 = EDGE_CURVE ( 'NONE', #5073, #39075, #90324, .T. ) ; +#41835 = LINE ( 'NONE', #34196, #24470 ) ; +#41836 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36940 ) ) ; +#41837 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8648700000000000276 ) ) ; +#41838 = SURFACE_STYLE_USAGE ( .BOTH. , #71971 ) ; +#41839 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41840 = PLANE ( 'NONE', #76228 ) ; +#41841 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41842 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40168 ) ) ; +#41843 = ORIENTED_EDGE ( 'NONE', *, *, #52708, .T. ) ; +#41844 = LINE ( 'NONE', #79650, #5175 ) ; +#41845 = ORIENTED_EDGE ( 'NONE', *, *, #65738, .T. ) ; +#41846 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#41848 = AXIS2_PLACEMENT_3D ( 'NONE', #86653, #57062, #72333 ) ; +#41847 = SURFACE_STYLE_USAGE ( .BOTH. , #50033 ) ; +#41850 = VECTOR ( 'NONE', #10801, 1000.000000000000000 ) ; +#41849 = PLANE ( 'NONE', #69713 ) ; +#41851 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41853 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41852 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41854 = FILL_AREA_STYLE ('',( #96944 ) ) ; +#41855 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#41856 = EDGE_CURVE ( 'NONE', #72170, #66277, #72874, .T. ) ; +#41857 = ORIENTED_EDGE ( 'NONE', *, *, #32530, .F. ) ; +#41858 = ORIENTED_EDGE ( 'NONE', *, *, #60939, .F. ) ; +#41859 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12395 ), #23948 ) ; +#41860 = FILL_AREA_STYLE ('',( #64830 ) ) ; +#41861 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80813, 'distance_accuracy_value', 'NONE'); +#41862 = SURFACE_STYLE_USAGE ( .BOTH. , #87811 ) ; +#41863 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999992895, -3.149999999999990585, 0.000000000000000000 ) ) ; +#41864 = CARTESIAN_POINT ( 'NONE', ( 5.978923124874956585, 3.287228875125044247, 0.8991599999999999593 ) ) ; +#41865 = VECTOR ( 'NONE', #65820, 1000.000000000000000 ) ; +#41866 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#41867 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85869 ) ) ; +#41868 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41869 = SURFACE_STYLE_FILL_AREA ( #34229 ) ; +#41870 = SURFACE_SIDE_STYLE ('',( #48011 ) ) ; +#41871 = ORIENTED_EDGE ( 'NONE', *, *, #84036, .F. ) ; +#41872 = EDGE_CURVE ( 'NONE', #36673, #71649, #73383, .T. ) ; +#41873 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#41874 = VERTEX_POINT ( 'NONE', #24932 ) ; +#41875 = AXIS2_PLACEMENT_3D ( 'NONE', #80805, #72609, #35360 ) ; +#41876 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#41877 = EDGE_LOOP ( 'NONE', ( #95105, #58742, #78186, #66245 ) ) ; +#41878 = SURFACE_SIDE_STYLE ('',( #49546 ) ) ; +#41879 = VECTOR ( 'NONE', #17471, 1000.000000000000000 ) ; +#41880 = SURFACE_SIDE_STYLE ('',( #25565 ) ) ; +#41881 = SURFACE_STYLE_FILL_AREA ( #56720 ) ; +#41882 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87570 ), #5947 ) ; +#41883 = CARTESIAN_POINT ( 'NONE', ( -1.010461395130570095, -1.072184731453450057, 0.8299999999999999600 ) ) ; +#41884 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#41885 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41887 = ORIENTED_EDGE ( 'NONE', *, *, #10573, .T. ) ; +#41886 = ORIENTED_EDGE ( 'NONE', *, *, #70889, .T. ) ; +#41888 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92360 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98571, #82364, #51727 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41889 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -2.258754526011470139E-17 ) ) ; +#41890 = LINE ( 'NONE', #11146, #57842 ) ; +#41891 = VERTEX_POINT ( 'NONE', #56059 ) ; +#41892 = VECTOR ( 'NONE', #33872, 1000.000000000000000 ) ; +#41893 = PLANE ( 'NONE', #88222 ) ; +#41895 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41894 = SURFACE_STYLE_FILL_AREA ( #81717 ) ; +#41896 = ORIENTED_EDGE ( 'NONE', *, *, #14244, .T. ) ; +#41897 = ORIENTED_EDGE ( 'NONE', *, *, #32550, .F. ) ; +#41898 = LINE ( 'NONE', #50083, #90531 ) ; +#41899 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#41900 = PLANE ( 'NONE', #26809 ) ; +#41901 = AXIS2_PLACEMENT_3D ( 'NONE', #58720, #42869, #27562 ) ; +#41902 = FACE_OUTER_BOUND ( 'NONE', #58500, .T. ) ; +#41903 = PLANE ( 'NONE', #71953 ) ; +#41904 = VERTEX_POINT ( 'NONE', #87183 ) ; +#41906 = ORIENTED_EDGE ( 'NONE', *, *, #42131, .T. ) ; +#41905 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59863 ) ) ; +#41907 = ORIENTED_EDGE ( 'NONE', *, *, #57789, .T. ) ; +#41908 = EDGE_CURVE ( 'NONE', #3032, #67375, #64208, .T. ) ; +#41909 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.7000000000000001776, -0.02000000000000000042 ) ) ; +#41910 = PRESENTATION_STYLE_ASSIGNMENT (( #18394 ) ) ; +#41911 = STYLED_ITEM ( 'NONE', ( #4496 ), #30622 ) ; +#41913 = ORIENTED_EDGE ( 'NONE', *, *, #66025, .T. ) ; +#41912 = CYLINDRICAL_SURFACE ( 'NONE', #49398, 0.2000000000000005107 ) ; +#41914 = FILL_AREA_STYLE ('',( #10665 ) ) ; +#41915 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63127 ) ) ; +#41916 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59602 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65815, #13101, #75469 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#41917 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#41918 = VERTEX_POINT ( 'NONE', #3917 ) ; +#41919 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41920 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#41921 = ORIENTED_EDGE ( 'NONE', *, *, #83364, .T. ) ; +#41922 = EDGE_CURVE ( 'NONE', #97167, #13289, #52917, .T. ) ; +#41923 = PRESENTATION_STYLE_ASSIGNMENT (( #11174 ) ) ; +#41924 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41925 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41926 = EDGE_CURVE ( 'NONE', #65675, #39103, #82057, .T. ) ; +#41927 = CARTESIAN_POINT ( 'NONE', ( 2.433333333333326465, -3.500000000000000000, 0.000000000000000000 ) ) ; +#41928 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45144 ) ) ; +#41929 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#41930 = LINE ( 'NONE', #49596, #85218 ) ; +#41931 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8991599999999999593 ) ) ; +#41932 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41934 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#41933 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#41935 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#41936 = EDGE_LOOP ( 'NONE', ( #84230, #30046, #30771, #82120, #29432, #6749, #91872, #90236 ) ) ; +#41937 = PLANE ( 'NONE', #50668 ) ; +#41938 = AXIS2_PLACEMENT_3D ( 'NONE', #25819, #79431, #57471 ) ; +#41939 = FILL_AREA_STYLE ('',( #17410 ) ) ; +#41940 = ORIENTED_EDGE ( 'NONE', *, *, #26269, .F. ) ; +#41941 = FACE_OUTER_BOUND ( 'NONE', #83915, .T. ) ; +#41942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#41943 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41944 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85937 ), #98899 ) ; +#41946 = EDGE_CURVE ( 'NONE', #55814, #62506, #12503, .T. ) ; +#41945 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8299999999999999600 ) ) ; +#41948 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41947 = CARTESIAN_POINT ( 'NONE', ( 1.150000000000000133, 0.7099999999999999645, -1.079289321881345298 ) ) ; +#41949 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#41950 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41951 = CLOSED_SHELL ( 'NONE', ( #88960, #15938, #76859, #49931, #16374, #46701 ) ) ; +#41952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41953 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41954 = ADVANCED_FACE ( 'NONE', ( #4898 ), #21744, .F. ) ; +#41955 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28877 ), #89317 ) ; +#41956 = SURFACE_STYLE_FILL_AREA ( #20450 ) ; +#41957 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#41958 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41959 = SURFACE_SIDE_STYLE ('',( #10184 ) ) ; +#41960 = VERTEX_POINT ( 'NONE', #35098 ) ; +#41961 = EDGE_CURVE ( 'NONE', #13371, #42518, #97796, .T. ) ; +#41962 = EDGE_CURVE ( 'NONE', #43736, #63412, #65931, .T. ) ; +#41963 = CARTESIAN_POINT ( 'NONE', ( 0.01456467927272207807, -1.295318215112642557, 0.8099999999998047651 ) ) ; +#41964 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#41965 = EDGE_CURVE ( 'NONE', #38122, #57773, #75873, .T. ) ; +#41966 = EDGE_LOOP ( 'NONE', ( #99900, #77360, #43590, #31086 ) ) ; +#41967 = PRESENTATION_STYLE_ASSIGNMENT (( #72099 ) ) ; +#41968 = PRODUCT_DEFINITION ( 'δ֪', '', #58481, #79010 ) ; +#41969 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8648700000000000276 ) ) ; +#41970 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#41971 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#41972 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#41974 = LINE ( 'NONE', #33306, #51525 ) ; +#41973 = STYLED_ITEM ( 'NONE', ( #73643 ), #18514 ) ; +#41975 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85973 ) ) ; +#41976 = CARTESIAN_POINT ( 'NONE', ( -1.061635297135890221, -1.433733517242619993, 0.8300000000000001821 ) ) ; +#41977 = FILL_AREA_STYLE_COLOUR ( '', #42728 ) ; +#41978 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50567, 'distance_accuracy_value', 'NONE'); +#41979 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#41980 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#41981 = EDGE_CURVE ( 'NONE', #34647, #1345, #31929, .T. ) ; +#41982 = EDGE_LOOP ( 'NONE', ( #17127, #57683, #86198, #72947 ) ) ; +#41983 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#41984 = EDGE_LOOP ( 'NONE', ( #65861, #48916, #21059, #99019 ) ) ; +#41985 = SURFACE_SIDE_STYLE ('',( #73121 ) ) ; +#41986 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8446, 'distance_accuracy_value', 'NONE'); +#41987 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21853, 'distance_accuracy_value', 'NONE'); +#41988 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#41989 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#41990 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155856999999999690, 0.8648700000000000276 ) ) ; +#41991 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55040 ), #76210 ) ; +#41992 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#41993 = FACE_OUTER_BOUND ( 'NONE', #51923, .T. ) ; +#41994 = FACE_OUTER_BOUND ( 'NONE', #77300, .T. ) ; +#41995 = PRESENTATION_STYLE_ASSIGNMENT (( #10740 ) ) ; +#41996 = ORIENTED_EDGE ( 'NONE', *, *, #43186, .T. ) ; +#41997 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#41998 = EDGE_CURVE ( 'NONE', #58410, #22670, #97320, .T. ) ; +#42000 = LINE ( 'NONE', #43479, #44953 ) ; +#41999 = VECTOR ( 'NONE', #82413, 999.9999999999998863 ) ; +#42001 = LINE ( 'NONE', #73635, #94941 ) ; +#42002 = VERTEX_POINT ( 'NONE', #28416 ) ; +#42003 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42004 = ORIENTED_EDGE ( 'NONE', *, *, #84899, .T. ) ; +#42005 = EDGE_CURVE ( 'NONE', #35156, #94814, #20746, .T. ) ; +#42006 = PLANE ( 'NONE', #80546 ) ; +#42007 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42008 = FILL_AREA_STYLE_COLOUR ( '', #65403 ) ; +#42009 = PLANE ( 'NONE', #31891 ) ; +#42010 = ORIENTED_EDGE ( 'NONE', *, *, #69145, .F. ) ; +#42011 = VECTOR ( 'NONE', #79907, 1000.000000000000000 ) ; +#42012 = EDGE_LOOP ( 'NONE', ( #25811, #17519, #24045, #4428 ) ) ; +#42013 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17547 ), #24089 ) ; +#42014 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12080 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100368, #46342, #93300 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42015 = CLOSED_SHELL ( 'NONE', ( #82699, #50242, #90120, #98646, #31644, #30020 ) ) ; +#42016 = VERTEX_POINT ( 'NONE', #83547 ) ; +#42017 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#42018 = CARTESIAN_POINT ( 'NONE', ( -0.4682333997055400099, -1.153630909546540018, 0.8100000000000000533 ) ) ; +#42019 = LINE ( 'NONE', #73166, #30631 ) ; +#42020 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#42022 = ORIENTED_EDGE ( 'NONE', *, *, #99199, .F. ) ; +#42021 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#42024 = ORIENTED_EDGE ( 'NONE', *, *, #21245, .T. ) ; +#42023 = VERTEX_POINT ( 'NONE', #58591 ) ; +#42025 = FILL_AREA_STYLE ('',( #18517 ) ) ; +#42026 = VERTEX_POINT ( 'NONE', #29414 ) ; +#42027 = ADVANCED_FACE ( 'NONE', ( #89694 ), #60583, .F. ) ; +#42028 = SURFACE_SIDE_STYLE ('',( #90483 ) ) ; +#42029 = ORIENTED_EDGE ( 'NONE', *, *, #49023, .F. ) ; +#42032 = EDGE_LOOP ( 'NONE', ( #94866, #62475, #44464, #12769 ) ) ; +#42031 = VECTOR ( 'NONE', #894, 1000.000000000000114 ) ; +#42030 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42033 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 4.849935000000000329, 0.8991599999999999593 ) ) ; +#42034 = FILL_AREA_STYLE_COLOUR ( '', #20358 ) ; +#42035 = PRESENTATION_STYLE_ASSIGNMENT (( #86473 ) ) ; +#42036 = VERTEX_POINT ( 'NONE', #77364 ) ; +#42037 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6166666666666666963, 0.000000000000000000 ) ) ; +#42038 = CARTESIAN_POINT ( 'NONE', ( -1.303800513451622844, 1.386208350606499939, 0.8299999999999999600 ) ) ; +#42039 = ORIENTED_EDGE ( 'NONE', *, *, #85125, .T. ) ; +#42040 = SURFACE_SIDE_STYLE ('',( #34897 ) ) ; +#42041 = CARTESIAN_POINT ( 'NONE', ( 4.557639000000000884, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#42042 = EDGE_CURVE ( 'NONE', #55177, #96609, #70726, .T. ) ; +#42043 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#42044 = AXIS2_PLACEMENT_3D ( 'NONE', #7130, #31713, #15346 ) ; +#42045 = EDGE_CURVE ( 'NONE', #61874, #10531, #54936, .T. ) ; +#42046 = FILL_AREA_STYLE ('',( #57909 ) ) ; +#42048 = PRESENTATION_STYLE_ASSIGNMENT (( #96636 ) ) ; +#42047 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42049 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42050 = SURFACE_SIDE_STYLE ('',( #11802 ) ) ; +#42051 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#42052 = STYLED_ITEM ( 'NONE', ( #69819 ), #84361 ) ; +#42054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42053 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#42055 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#42056 = FILL_AREA_STYLE ('',( #66533 ) ) ; +#42057 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#42058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42059 = VECTOR ( 'NONE', #5707, 1000.000000000000000 ) ; +#42060 = CARTESIAN_POINT ( 'NONE', ( 0.9823626554959720147, -1.038425069758839969, 0.8299999999999999600 ) ) ; +#42061 = ORIENTED_EDGE ( 'NONE', *, *, #94523, .F. ) ; +#42062 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42064 = CARTESIAN_POINT ( 'NONE', ( 4.380811213087555167, 1.410337779954151882, -11.92000896989550007 ) ) ; +#42065 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6130 ) ) ; +#42066 = ORIENTED_EDGE ( 'NONE', *, *, #39885, .T. ) ; +#42067 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42068 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#42069 = STYLED_ITEM ( 'NONE', ( #83781 ), #24724 ) ; +#42070 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42071 = EDGE_CURVE ( 'NONE', #13319, #64241, #39087, .T. ) ; +#42073 = FILL_AREA_STYLE_COLOUR ( '', #57499 ) ; +#42072 = LINE ( 'NONE', #55403, #60451 ) ; +#42074 = CARTESIAN_POINT ( 'NONE', ( 1.602494679827060287, -1.010243534007990052, 0.8299999999999999600 ) ) ; +#42075 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42076 = VECTOR ( 'NONE', #24420, 1000.000000000000000 ) ; +#42077 = STYLED_ITEM ( 'NONE', ( #27075 ), #16474 ) ; +#42078 = FILL_AREA_STYLE_COLOUR ( '', #26559 ) ; +#42079 = VECTOR ( 'NONE', #60154, 1000.000000000000000 ) ; +#42080 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42081 = ORIENTED_EDGE ( 'NONE', *, *, #453, .F. ) ; +#42082 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23816, #2845, #41153, #16106 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42083 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76741 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6945, #47348, #39688 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42084 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42085 = AXIS2_PLACEMENT_3D ( 'NONE', #10612, #24567, #72484 ) ; +#42086 = FILL_AREA_STYLE ('',( #2777 ) ) ; +#42087 = CARTESIAN_POINT ( 'NONE', ( 0.9913778824254210198, -0.9987792914302020542, 0.8299999999999994049 ) ) ; +#42088 = FILL_AREA_STYLE_COLOUR ( '', #45211 ) ; +#42089 = CARTESIAN_POINT ( 'NONE', ( 8.793208750250085970, 9.241067249749910673, 0.8991599999999999593 ) ) ; +#42090 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#42091 = SURFACE_STYLE_FILL_AREA ( #10853 ) ; +#42092 = LINE ( 'NONE', #66075, #74641 ) ; +#42093 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.449999999999999956, 0.000000000000000000 ) ) ; +#42094 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#42095 = PLANE ( 'NONE', #62272 ) ; +#42096 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74101, 'distance_accuracy_value', 'NONE'); +#42097 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50663 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83151, #13619, #68793 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42098 = FILL_AREA_STYLE ('',( #81428 ) ) ; +#42099 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42100 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63331 ), #11017 ) ; +#42101 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220780591, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#42102 = ORIENTED_EDGE ( 'NONE', *, *, #22378, .F. ) ; +#42103 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42104 = EDGE_LOOP ( 'NONE', ( #41858, #38245, #55443, #58771, #8436 ) ) ; +#42105 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21373, 'distance_accuracy_value', 'NONE'); +#42106 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35068, 'distance_accuracy_value', 'NONE'); +#42107 = CIRCLE ( 'NONE', #76323, 0.009999999999999998473 ) ; +#42108 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000002623, -0.1350000000000000089 ) ) ; +#42109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42110 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42111 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42112 = LINE ( 'NONE', #43584, #59073 ) ; +#42113 = SURFACE_STYLE_FILL_AREA ( #10867 ) ; +#42114 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#42116 = VERTEX_POINT ( 'NONE', #7351 ) ; +#42115 = VECTOR ( 'NONE', #91126, 1000.000000000000000 ) ; +#42117 = ADVANCED_FACE ( 'NONE', ( #38580 ), #100733, .T. ) ; +#42118 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#42119 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60515, 'distance_accuracy_value', 'NONE'); +#42120 = SURFACE_SIDE_STYLE ('',( #49275 ) ) ; +#42121 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #93897, .NOT_KNOWN. ) ; +#42122 = FACE_OUTER_BOUND ( 'NONE', #95135, .T. ) ; +#42123 = AXIS2_PLACEMENT_3D ( 'NONE', #41602, #97186, #96682 ) ; +#42124 = ORIENTED_EDGE ( 'NONE', *, *, #5130, .F. ) ; +#42125 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#42126 = SURFACE_STYLE_FILL_AREA ( #3805 ) ; +#42127 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42128 = PLANE ( 'NONE', #50573 ) ; +#42129 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#42130 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42131 = EDGE_CURVE ( 'NONE', #34143, #94818, #74794, .T. ) ; +#42132 = ORIENTED_EDGE ( 'NONE', *, *, #89517, .T. ) ; +#42133 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#42134 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73606, 'distance_accuracy_value', 'NONE'); +#42135 = SURFACE_STYLE_USAGE ( .BOTH. , #25817 ) ; +#42136 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#42137 = EDGE_CURVE ( 'NONE', #49661, #76676, #92186, .T. ) ; +#42138 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8991599999999999593 ) ) ; +#42139 = VECTOR ( 'NONE', #1917, 1000.000000000000000 ) ; +#42140 = ORIENTED_EDGE ( 'NONE', *, *, #871, .F. ) ; +#42141 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#42142 = LINE ( 'NONE', #3822, #64145 ) ; +#42143 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42144 = AXIS2_PLACEMENT_3D ( 'NONE', #33280, #79756, #72562 ) ; +#42145 = CARTESIAN_POINT ( 'NONE', ( -1.324701217740638759, -1.163560561378816471, 0.8099999999998677147 ) ) ; +#42146 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42147 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#42148 = EDGE_CURVE ( 'NONE', #77521, #27941, #22252, .T. ) ; +#42149 = ADVANCED_FACE ( 'NONE', ( #53400 ), #84528, .F. ) ; +#42150 = AXIS2_PLACEMENT_3D ( 'NONE', #55862, #62519, #701 ) ; +#42151 = VECTOR ( 'NONE', #36582, 1000.000000000000000 ) ; +#42152 = AXIS2_PLACEMENT_3D ( 'NONE', #44662, #21196, #92133 ) ; +#42153 = EDGE_CURVE ( 'NONE', #61927, #51666, #26305, .T. ) ; +#42154 = ORIENTED_EDGE ( 'NONE', *, *, #40909, .F. ) ; +#42155 = EDGE_CURVE ( 'NONE', #81594, #26125, #33463, .T. ) ; +#42157 = EDGE_LOOP ( 'NONE', ( #69188, #57288, #96617, #20808 ) ) ; +#42156 = FILL_AREA_STYLE_COLOUR ( '', #94832 ) ; +#42158 = AXIS2_PLACEMENT_3D ( 'NONE', #50433, #79531, #10464 ) ; +#42159 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42160 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42161 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42162 = FILL_AREA_STYLE ('',( #82469 ) ) ; +#42163 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#42164 = VECTOR ( 'NONE', #61406, 1000.000000000000000 ) ; +#42165 = SURFACE_STYLE_FILL_AREA ( #65619 ) ; +#42166 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#42167 = VERTEX_POINT ( 'NONE', #71232 ) ; +#42168 = CARTESIAN_POINT ( 'NONE', ( 1.248152242693560066, -1.513291690750319995, 0.8100000000000000533 ) ) ; +#42169 = EDGE_CURVE ( 'NONE', #19650, #29642, #25804, .T. ) ; +#42170 = VERTEX_POINT ( 'NONE', #40107 ) ; +#42171 = STYLED_ITEM ( 'NONE', ( #51001 ), #50579 ) ; +#42172 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42173 = VERTEX_POINT ( 'NONE', #48789 ) ; +#42174 = ORIENTED_EDGE ( 'NONE', *, *, #22477, .F. ) ; +#42175 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#42176 = ADVANCED_FACE ( 'NONE', ( #56965 ), #88561, .F. ) ; +#42177 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75025 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59080, #90165, #33575 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42179 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#42178 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42180 = PRESENTATION_STYLE_ASSIGNMENT (( #10927 ) ) ; +#42181 = SURFACE_STYLE_USAGE ( .BOTH. , #2869 ) ; +#42182 = ORIENTED_EDGE ( 'NONE', *, *, #90652, .F. ) ; +#42183 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14408 ) ) ; +#42184 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#42185 = PRESENTATION_STYLE_ASSIGNMENT (( #3372 ) ) ; +#42186 = EDGE_LOOP ( 'NONE', ( #21185, #96729, #74793, #43425 ) ) ; +#42187 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#42188 = ORIENTED_EDGE ( 'NONE', *, *, #60750, .T. ) ; +#42189 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42190 = FACE_OUTER_BOUND ( 'NONE', #57516, .T. ) ; +#42191 = CARTESIAN_POINT ( 'NONE', ( -1.336283849596160200, -1.153389236204189983, 0.8299999999999999600 ) ) ; +#42192 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.500000000000000000, 0.1829999999999999960 ) ) ; +#42193 = PRESENTATION_STYLE_ASSIGNMENT (( #81004 ) ) ; +#42194 = STYLED_ITEM ( 'NONE', ( #65310 ), #32110 ) ; +#42195 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42196 = PRESENTATION_STYLE_ASSIGNMENT (( #82007 ) ) ; +#42197 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53510, #46822, #68300, #84640 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42198 = LINE ( 'NONE', #26375, #68201 ) ; +#42199 = STYLED_ITEM ( 'NONE', ( #62200 ), #31728 ) ; +#42200 = ORIENTED_EDGE ( 'NONE', *, *, #60285, .F. ) ; +#42201 = CARTESIAN_POINT ( 'NONE', ( 1.261158141153259971, -1.441583773770549914, 0.8299999999999994049 ) ) ; +#42202 = ADVANCED_FACE ( 'NONE', ( #42122 ), #3311, .T. ) ; +#42203 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8991599999999999593 ) ) ; +#42204 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, -3.099999999999992539, -0.02000000000000000042 ) ) ; +#42205 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79747 ) ) ; +#42206 = PRESENTATION_STYLE_ASSIGNMENT (( #34564 ) ) ; +#42207 = STYLED_ITEM ( 'NONE', ( #54292 ), #84760 ) ; +#42208 = SURFACE_STYLE_FILL_AREA ( #4378 ) ; +#42209 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42210 = ADVANCED_FACE ( 'NONE', ( #44110 ), #36963, .T. ) ; +#42211 = DIRECTION ( 'NONE', ( 6.179952383168509971E-14, -1.000000000000000000, 0.000000000000000000 ) ) ; +#42212 = EDGE_LOOP ( 'NONE', ( #60756, #81820, #79163, #89028 ) ) ; +#42213 = LINE ( 'NONE', #26894, #37489 ) ; +#42214 = AXIS2_PLACEMENT_3D ( 'NONE', #921, #63243, #94328 ) ; +#42215 = LINE ( 'NONE', #19719, #52933 ) ; +#42216 = SURFACE_SIDE_STYLE ('',( #44187 ) ) ; +#42217 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.000000000000000000 ) ) ; +#42218 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83918 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84986, #14996, #28021 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42219 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36848, 'distance_accuracy_value', 'NONE'); +#42220 = LINE ( 'NONE', #57555, #45635 ) ; +#42221 = SURFACE_SIDE_STYLE ('',( #48878 ) ) ; +#42222 = SURFACE_STYLE_USAGE ( .BOTH. , #50414 ) ; +#42223 = VECTOR ( 'NONE', #40300, 1000.000000000000000 ) ; +#42224 = DIRECTION ( 'NONE', ( -0.7071075504167442238, -0.7071060119555140355, 0.000000000000000000 ) ) ; +#42226 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#42225 = PRESENTATION_STYLE_ASSIGNMENT (( #64688 ) ) ; +#42227 = LINE ( 'NONE', #80030, #92780 ) ; +#42228 = VECTOR ( 'NONE', #46051, 1000.000000000000000 ) ; +#42229 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42230 = LINE ( 'NONE', #79521, #13647 ) ; +#42231 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74628 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61969, #21632, #7724 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42232 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#42233 = SURFACE_STYLE_USAGE ( .BOTH. , #85264 ) ; +#42234 = CARTESIAN_POINT ( 'NONE', ( -0.1534467802446229934, -0.9032194100038879458, 0.8300000000000009592 ) ) ; +#42235 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24240 ), #63455 ) ; +#42236 = PRESENTATION_STYLE_ASSIGNMENT (( #18709 ) ) ; +#42237 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999901329, 0.4300000000264844191, 0.6499230724029858575 ) ) ; +#42238 = ORIENTED_EDGE ( 'NONE', *, *, #40364, .F. ) ; +#42239 = SURFACE_STYLE_USAGE ( .BOTH. , #57573 ) ; +#42240 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#42241 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60559, 'distance_accuracy_value', 'NONE'); +#42242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42243 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60294, 'distance_accuracy_value', 'NONE'); +#42244 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#42245 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1492 ) ) ; +#42246 = VECTOR ( 'NONE', #86548, 1000.000000000000000 ) ; +#42247 = EDGE_LOOP ( 'NONE', ( #12576, #2470, #51032, #20997 ) ) ; +#42248 = LINE ( 'NONE', #96824, #39024 ) ; +#42249 = FILL_AREA_STYLE_COLOUR ( '', #20409 ) ; +#42250 = FILL_AREA_STYLE ('',( #26931 ) ) ; +#42251 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63662, 'distance_accuracy_value', 'NONE'); +#42252 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94521, 'distance_accuracy_value', 'NONE'); +#42253 = FILL_AREA_STYLE_COLOUR ( '', #10823 ) ; +#42254 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42255 = EDGE_LOOP ( 'NONE', ( #20779, #65888, #35842, #31210 ) ) ; +#42256 = ORIENTED_EDGE ( 'NONE', *, *, #35336, .T. ) ; +#42257 = FACE_OUTER_BOUND ( 'NONE', #90956, .T. ) ; +#42258 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#42259 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91144 ), #81496 ) ; +#42260 = EDGE_LOOP ( 'NONE', ( #2890, #17279, #52810, #60626, #92741, #17229 ) ) ; +#42261 = CARTESIAN_POINT ( 'NONE', ( 1.779394466811810016, -1.241062917987890257, 0.8100000000000000533 ) ) ; +#42262 = VECTOR ( 'NONE', #47799, 1000.000000000000000 ) ; +#42263 = PRESENTATION_STYLE_ASSIGNMENT (( #28927 ) ) ; +#42264 = FILL_AREA_STYLE_COLOUR ( '', #17406 ) ; +#42265 = SURFACE_SIDE_STYLE ('',( #74907 ) ) ; +#42266 = CARTESIAN_POINT ( 'NONE', ( -1.254664462595540098, -0.9005718509792439708, 0.8299999999999997380 ) ) ; +#42267 = VECTOR ( 'NONE', #59737, 1000.000000000000000 ) ; +#42268 = VECTOR ( 'NONE', #79003, 1000.000000000000000 ) ; +#42269 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #71727, #55681 ) ; +#42270 = FILL_AREA_STYLE_COLOUR ( '', #5229 ) ; +#42272 = ORIENTED_EDGE ( 'NONE', *, *, #72699, .T. ) ; +#42271 = ORIENTED_EDGE ( 'NONE', *, *, #41578, .F. ) ; +#42273 = ORIENTED_EDGE ( 'NONE', *, *, #33499, .F. ) ; +#42274 = ORIENTED_EDGE ( 'NONE', *, *, #59008, .F. ) ; +#42275 = VECTOR ( 'NONE', #10866, 1000.000000000000000 ) ; +#42276 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#42278 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2784314575050761964, -0.1458578643762690474 ) ) ; +#42277 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42279 = VERTEX_POINT ( 'NONE', #75266 ) ; +#42280 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78121 ), #66736 ) ; +#42281 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86274 ), #9384 ) ; +#42282 = STYLED_ITEM ( 'NONE', ( #20252 ), #6232 ) ; +#42283 = FACE_OUTER_BOUND ( 'NONE', #43709, .T. ) ; +#42284 = EDGE_CURVE ( 'NONE', #8528, #41874, #27306, .T. ) ; +#42285 = VERTEX_POINT ( 'NONE', #44582 ) ; +#42286 = STYLED_ITEM ( 'NONE', ( #13872 ), #80364 ) ; +#42287 = PRESENTATION_STYLE_ASSIGNMENT (( #24969 ) ) ; +#42288 = VERTEX_POINT ( 'NONE', #35980 ) ; +#42290 = PLANE ( 'NONE', #43640 ) ; +#42289 = PRESENTATION_STYLE_ASSIGNMENT (( #66745 ) ) ; +#42291 = ORIENTED_EDGE ( 'NONE', *, *, #33065, .F. ) ; +#42292 = ORIENTED_EDGE ( 'NONE', *, *, #47961, .T. ) ; +#42293 = FILL_AREA_STYLE ('',( #33633 ) ) ; +#42294 = EDGE_CURVE ( 'NONE', #79176, #13157, #19626, .T. ) ; +#42295 = SURFACE_SIDE_STYLE ('',( #63771 ) ) ; +#42296 = STYLED_ITEM ( 'NONE', ( #5986 ), #63617 ) ; +#42297 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#42298 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14530 ), #29232 ) ; +#42299 = FILL_AREA_STYLE_COLOUR ( '', #42480 ) ; +#42301 = ORIENTED_EDGE ( 'NONE', *, *, #49937, .F. ) ; +#42300 = FACE_OUTER_BOUND ( 'NONE', #15471, .T. ) ; +#42302 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#42303 = ORIENTED_EDGE ( 'NONE', *, *, #5018, .F. ) ; +#42304 = CARTESIAN_POINT ( 'NONE', ( -0.1725832855250629960, -0.9074576374047380600, 0.8100000000000000533 ) ) ; +#42305 = FILL_AREA_STYLE ('',( #50976 ) ) ; +#42306 = ORIENTED_EDGE ( 'NONE', *, *, #86405, .T. ) ; +#42307 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42308 = ORIENTED_EDGE ( 'NONE', *, *, #66828, .T. ) ; +#42309 = EDGE_LOOP ( 'NONE', ( #71184, #23417, #50299, #64994 ) ) ; +#42310 = PLANE ( 'NONE', #9003 ) ; +#42311 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20726, #51890, #5861, #51395 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42312 = SURFACE_STYLE_FILL_AREA ( #96388 ) ; +#42313 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91199 ), #86307 ) ; +#42314 = CARTESIAN_POINT ( 'NONE', ( -1.257861918732770645, -1.117969024486352048, 0.8099999999999012434 ) ) ; +#42315 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78237 ), #68371 ) ; +#42316 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1833333333333329873, 0.000000000000000000 ) ) ; +#42317 = ORIENTED_EDGE ( 'NONE', *, *, #40778, .T. ) ; +#42318 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#42319 = ORIENTED_EDGE ( 'NONE', *, *, #23965, .F. ) ; +#42320 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7519, #32119, #46388, #23976 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42321 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602299999999858, 0.8648700000000000276 ) ) ; +#42322 = SURFACE_SIDE_STYLE ('',( #41819 ) ) ; +#42323 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11236 ), #22771 ) ; +#42324 = CARTESIAN_POINT ( 'NONE', ( 1.285853239104850054, -1.172828961844079920, 0.8100000000000000533 ) ) ; +#42325 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#42326 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42327 = PLANE ( 'NONE', #92407 ) ; +#42328 = FILL_AREA_STYLE ('',( #40825 ) ) ; +#42329 = FILL_AREA_STYLE ('',( #3524 ) ) ; +#42330 = EDGE_CURVE ( 'NONE', #59034, #57512, #28300, .T. ) ; +#42331 = SURFACE_STYLE_FILL_AREA ( #40826 ) ; +#42332 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42333 = ORIENTED_EDGE ( 'NONE', *, *, #42505, .F. ) ; +#42334 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -1.699999999999999956, 0.000000000000000000 ) ) ; +#42335 = CARTESIAN_POINT ( 'NONE', ( 0.1751932085031089881, -1.046109390704299980, 0.8100000000000000533 ) ) ; +#42336 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42337 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#42338 = PRESENTATION_STYLE_ASSIGNMENT (( #3019 ) ) ; +#42339 = CARTESIAN_POINT ( 'NONE', ( 1.282695938257045087, -1.509576801066649265, 0.8099999999996694289 ) ) ; +#42340 = COLOUR_RGB ( '',0.6666666666666666297, 0.6666666666666666297, 0.6666666666666666297 ) ; +#42341 = STYLED_ITEM ( 'NONE', ( #96184 ), #32035 ) ; +#42342 = LINE ( 'NONE', #34699, #41865 ) ; +#42343 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42344 = FACE_OUTER_BOUND ( 'NONE', #78441, .T. ) ; +#42345 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#42346 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.6999999999999990674, 0.000000000000000000 ) ) ; +#42347 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56590 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10475, #50440, #87692 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42348 = AXIS2_PLACEMENT_3D ( 'NONE', #87930, #78274, #86940 ) ; +#42349 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42350 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32293, 'distance_accuracy_value', 'NONE'); +#42351 = AXIS2_PLACEMENT_3D ( 'NONE', #98015, #28645, #68917 ) ; +#42352 = ORIENTED_EDGE ( 'NONE', *, *, #53844, .F. ) ; +#42353 = CARTESIAN_POINT ( 'NONE', ( -0.9337505133853429840, 2.302534075926970125, 0.8100000000000000533 ) ) ; +#42354 = SURFACE_STYLE_USAGE ( .BOTH. , #17830 ) ; +#42355 = SURFACE_STYLE_USAGE ( .BOTH. , #81170 ) ; +#42356 = ORIENTED_EDGE ( 'NONE', *, *, #6422, .F. ) ; +#42357 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#42358 = EDGE_CURVE ( 'NONE', #83788, #63839, #81452, .T. ) ; +#42359 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91234 ) ) ; +#42360 = FILL_AREA_STYLE ('',( #11105 ) ) ; +#42361 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01499999999999999944, -0.1400000000000000133 ) ) ; +#42362 = AXIS2_PLACEMENT_3D ( 'NONE', #71591, #95025, #53737 ) ; +#42363 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#42364 = EDGE_CURVE ( 'NONE', #59639, #7390, #74763, .T. ) ; +#42365 = FILL_AREA_STYLE_COLOUR ( '', #4188 ) ; +#42366 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57038 ), #68492 ) ; +#42367 = ORIENTED_EDGE ( 'NONE', *, *, #99501, .T. ) ; +#42368 = ORIENTED_EDGE ( 'NONE', *, *, #67418, .F. ) ; +#42369 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#42370 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42371 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42372 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10358 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78564, #39258, #61773 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42373 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#42374 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#42375 = FACE_OUTER_BOUND ( 'NONE', #18436, .T. ) ; +#42376 = PRESENTATION_STYLE_ASSIGNMENT (( #49030 ) ) ; +#42377 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14827, 'distance_accuracy_value', 'NONE'); +#42378 = PRESENTATION_STYLE_ASSIGNMENT (( #72003 ) ) ; +#42379 = ADVANCED_FACE ( 'NONE', ( #66587 ), #97685, .T. ) ; +#42380 = EDGE_CURVE ( 'NONE', #10619, #4959, #70789, .T. ) ; +#42381 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42382 = VERTEX_POINT ( 'NONE', #84910 ) ; +#42383 = EDGE_LOOP ( 'NONE', ( #31228, #98591, #13280, #91061 ) ) ; +#42385 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#42384 = VECTOR ( 'NONE', #5480, 1000.000000000000000 ) ; +#42386 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#42387 = PLANE ( 'NONE', #49961 ) ; +#42388 = AXIS2_PLACEMENT_3D ( 'NONE', #55038, #25414, #80035 ) ; +#42389 = LINE ( 'NONE', #35251, #75699 ) ; +#42390 = CARTESIAN_POINT ( 'NONE', ( -1.066869350290160279, -0.9766832120545909657, 0.8100000000000000533 ) ) ; +#42391 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42392 = CARTESIAN_POINT ( 'NONE', ( -0.4015774049763590758, -0.9593865114130070149, 0.8100000000000000533 ) ) ; +#42393 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42395 = ORIENTED_EDGE ( 'NONE', *, *, #16929, .F. ) ; +#42394 = ORIENTED_EDGE ( 'NONE', *, *, #28779, .F. ) ; +#42396 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#42397 = STYLED_ITEM ( 'NONE', ( #97690 ), #44691 ) ; +#42398 = ORIENTED_EDGE ( 'NONE', *, *, #81795, .T. ) ; +#42399 = ADVANCED_FACE ( 'NONE', ( #14424 ), #15958, .T. ) ; +#42400 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86398 ) ) ; +#42401 = LINE ( 'NONE', #71524, #32826 ) ; +#42402 = ORIENTED_EDGE ( 'NONE', *, *, #37366, .F. ) ; +#42403 = ORIENTED_EDGE ( 'NONE', *, *, #28218, .T. ) ; +#42404 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42405 = SURFACE_STYLE_USAGE ( .BOTH. , #96482 ) ; +#42406 = VECTOR ( 'NONE', #61346, 1000.000000000000000 ) ; +#42408 = SURFACE_SIDE_STYLE ('',( #80218 ) ) ; +#42407 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42409 = ORIENTED_EDGE ( 'NONE', *, *, #24421, .T. ) ; +#42410 = ORIENTED_EDGE ( 'NONE', *, *, #80887, .T. ) ; +#42411 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42412 = ORIENTED_EDGE ( 'NONE', *, *, #27171, .F. ) ; +#42413 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42414 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42415 = VECTOR ( 'NONE', #96365, 1000.000000000000000 ) ; +#42416 = ADVANCED_FACE ( 'NONE', ( #31294 ), #8240, .T. ) ; +#42417 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6465 ), #63631 ) ; +#42418 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71776 ) ) ; +#42420 = ORIENTED_EDGE ( 'NONE', *, *, #85988, .T. ) ; +#42419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84734 ), #52192 ) ; +#42422 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#42423 = FACE_OUTER_BOUND ( 'NONE', #15722, .T. ) ; +#42424 = SURFACE_STYLE_USAGE ( .BOTH. , #11169 ) ; +#42425 = ORIENTED_EDGE ( 'NONE', *, *, #84585, .F. ) ; +#42426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93438, #45959, #30656 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42427 = ORIENTED_EDGE ( 'NONE', *, *, #38700, .T. ) ; +#42428 = FILL_AREA_STYLE ('',( #81249 ) ) ; +#42429 = VECTOR ( 'NONE', #37494, 1000.000000000000114 ) ; +#42430 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42432 = FILL_AREA_STYLE ('',( #27120 ) ) ; +#42431 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48997 ) ) ; +#42433 = ADVANCED_FACE ( 'NONE', ( #55813 ), #47634, .T. ) ; +#42434 = LINE ( 'NONE', #88379, #9009 ) ; +#42435 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42436 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#42437 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42438 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#42440 = CARTESIAN_POINT ( 'NONE', ( -0.7522321428571430157, 0.6899999999999999467, 0.2077922077922079724 ) ) ; +#42439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42441 = ADVANCED_FACE ( 'NONE', ( #16967 ), #9752, .T. ) ; +#42442 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8648700000000000276 ) ) ; +#42443 = ORIENTED_EDGE ( 'NONE', *, *, #65139, .F. ) ; +#42444 = LINE ( 'NONE', #24633, #70148 ) ; +#42445 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42446 = FILL_AREA_STYLE ('',( #96014 ) ) ; +#42447 = VERTEX_POINT ( 'NONE', #72621 ) ; +#42448 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27807 ) ) ; +#42449 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 0.8999999999999991340, -5.977360615245821520E-90 ) ) ; +#42450 = VECTOR ( 'NONE', #79252, 1000.000000000000000 ) ; +#42451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42452 = LINE ( 'NONE', #65925, #62879 ) ; +#42453 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2808578643762706939, 0.1500000000000000222 ) ) ; +#42454 = CARTESIAN_POINT ( 'NONE', ( 1.797929489527180014, -1.085974092738730024, 0.8299999999999999600 ) ) ; +#42455 = EDGE_CURVE ( 'NONE', #32195, #73941, #89080, .T. ) ; +#42456 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#42457 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#42458 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#42459 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42460 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#42461 = LINE ( 'NONE', #58311, #38411 ) ; +#42462 = ORIENTED_EDGE ( 'NONE', *, *, #39082, .T. ) ; +#42463 = SURFACE_SIDE_STYLE ('',( #35325 ) ) ; +#42465 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42464 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#42466 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42468 = AXIS2_PLACEMENT_3D ( 'NONE', #62348, #72018, #21 ) ; +#42467 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#42469 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84260, 'distance_accuracy_value', 'NONE'); +#42470 = VERTEX_POINT ( 'NONE', #31806 ) ; +#42471 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000025258, 0.1500000000000000222 ) ) ; +#42472 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#42473 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, 0.000000000000000000 ) ) ; +#42474 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#42475 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46188 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45206, #76373, #22260 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42476 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42477 = LINE ( 'NONE', #89923, #88797 ) ; +#42478 = ADVANCED_FACE ( 'N', ( #86647 ), #352, .T. ) ; +#42479 = PRODUCT ( 'Submodel-IPEX_4P_part_IPEX_4P', 'Submodel-IPEX_4P_part_IPEX_4P', '', ( #85686 ) ) ; +#42480 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42481 = ORIENTED_EDGE ( 'NONE', *, *, #37891, .T. ) ; +#42482 = PLANE ( 'NONE', #59618 ) ; +#42483 = ORIENTED_EDGE ( 'NONE', *, *, #28014, .T. ) ; +#42484 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49933, 'distance_accuracy_value', 'NONE'); +#42485 = VECTOR ( 'NONE', #47301, 1000.000000000000114 ) ; +#42486 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44228 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25207, #56357, #17484 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42487 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6542 ) ) ; +#42488 = LINE ( 'NONE', #3666, #12878 ) ; +#42489 = SURFACE_STYLE_FILL_AREA ( #64959 ) ; +#42490 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42491 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44139 ) ) ; +#42492 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#42493 = VERTEX_POINT ( 'NONE', #40708 ) ; +#42494 = EDGE_CURVE ( 'NONE', #37943, #55619, #40199, .T. ) ; +#42495 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42496 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42497 = STYLED_ITEM ( 'NONE', ( #60618 ), #6921 ) ; +#42498 = EDGE_CURVE ( 'NONE', #50740, #49623, #39675, .T. ) ; +#42499 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42500 = ORIENTED_EDGE ( 'NONE', *, *, #15957, .T. ) ; +#42501 = FILL_AREA_STYLE ('',( #18483 ) ) ; +#42502 = STYLED_ITEM ( 'NONE', ( #84143 ), #80952 ) ; +#42503 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42504 = EDGE_LOOP ( 'NONE', ( #94606, #75986, #41504, #25719 ) ) ; +#42505 = EDGE_CURVE ( 'NONE', #93216, #72570, #1893, .T. ) ; +#42506 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#42507 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8648700000000000276 ) ) ; +#42508 = STYLED_ITEM ( 'NONE', ( #45049 ), #2033 ) ; +#42509 = VERTEX_POINT ( 'NONE', #8950 ) ; +#42510 = VECTOR ( 'NONE', #34521, 1000.000000000000227 ) ; +#42511 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42512 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#42513 = ORIENTED_EDGE ( 'NONE', *, *, #29939, .T. ) ; +#42514 = EDGE_CURVE ( 'NONE', #88871, #57773, #71325, .T. ) ; +#42515 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85594, 'distance_accuracy_value', 'NONE'); +#42516 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42517 = VERTEX_POINT ( 'NONE', #80015 ) ; +#42518 = VERTEX_POINT ( 'NONE', #9952 ) ; +#42519 = EDGE_CURVE ( 'NONE', #44988, #75510, #70817, .T. ) ; +#42520 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42521 = SURFACE_STYLE_USAGE ( .BOTH. , #65473 ) ; +#42522 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#42523 = CARTESIAN_POINT ( 'NONE', ( -0.4616949353561959901, -1.145331018069290163, 0.8100000000000000533 ) ) ; +#42524 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#42525 = CARTESIAN_POINT ( 'NONE', ( 0.2502762232558249922, -1.044215898305860035, 0.8299999999999999600 ) ) ; +#42526 = ORIENTED_EDGE ( 'NONE', *, *, #8939, .F. ) ; +#42528 = ORIENTED_EDGE ( 'NONE', *, *, #18425, .T. ) ; +#42527 = ORIENTED_EDGE ( 'NONE', *, *, #40256, .T. ) ; +#42529 = SURFACE_STYLE_FILL_AREA ( #81357 ) ; +#42530 = ORIENTED_EDGE ( 'NONE', *, *, #2252, .T. ) ; +#42531 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71899 ) ) ; +#42532 = FACE_OUTER_BOUND ( 'NONE', #74758, .T. ) ; +#42533 = EDGE_CURVE ( 'NONE', #85879, #27473, #86128, .T. ) ; +#42534 = AXIS2_PLACEMENT_3D ( 'NONE', #90711, #97808, #28429 ) ; +#42535 = EDGE_LOOP ( 'NONE', ( #95645, #83236, #39877, #10044 ) ) ; +#42536 = ORIENTED_EDGE ( 'NONE', *, *, #24772, .T. ) ; +#42537 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42538 = ORIENTED_EDGE ( 'NONE', *, *, #11132, .T. ) ; +#42539 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42540 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#42541 = SURFACE_STYLE_FILL_AREA ( #41538 ) ; +#42542 = EDGE_LOOP ( 'NONE', ( #85524, #58622, #43609, #58790 ) ) ; +#42543 = FILL_AREA_STYLE ('',( #81376 ) ) ; +#42544 = CARTESIAN_POINT ( 'NONE', ( 0.1681119866146556230, 0.5791465759269649460, 0.8100000000000000533 ) ) ; +#42545 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42546 = CIRCLE ( 'NONE', #99493, 0.1200000000000000927 ) ; +#42547 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42548 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42549 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42551 = CARTESIAN_POINT ( 'NONE', ( 10.53976224974991283, 8.413752750250088397, 0.8648700000000000276 ) ) ; +#42550 = SURFACE_SIDE_STYLE ('',( #20551 ) ) ; +#42552 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42553 = SURFACE_SIDE_STYLE ('',( #19040 ) ) ; +#42554 = ADVANCED_FACE ( 'NONE', ( #63686 ), #57052, .T. ) ; +#42555 = LINE ( 'NONE', #3739, #35873 ) ; +#42556 = VECTOR ( 'NONE', #44157, 1000.000000000000000 ) ; +#42557 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18022 ) ) ; +#42560 = SURFACE_SIDE_STYLE ('',( #34916 ) ) ; +#42559 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.8500000000070031536, 0.6499230723533214737 ) ) ; +#42561 = LINE ( 'NONE', #4250, #63299 ) ; +#42562 = FACE_OUTER_BOUND ( 'NONE', #12743, .T. ) ; +#42563 = EDGE_CURVE ( 'NONE', #56115, #28424, #74349, .T. ) ; +#42564 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#42565 = VECTOR ( 'NONE', #7757, 1000.000000000000000 ) ; +#42566 = AXIS2_PLACEMENT_3D ( 'NONE', #35952, #83891, #83405 ) ; +#42568 = ADVANCED_FACE ( 'NONE', ( #96786 ), #10435, .F. ) ; +#42567 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#42569 = ORIENTED_EDGE ( 'NONE', *, *, #89228, .F. ) ; +#42570 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, -8.400000000000000355, -11.91999999999999993 ) ) ; +#42571 = LINE ( 'NONE', #3756, #74861 ) ; +#42572 = PRESENTATION_STYLE_ASSIGNMENT (( #3255 ) ) ; +#42573 = FILL_AREA_STYLE_COLOUR ( '', #36345 ) ; +#42574 = ORIENTED_EDGE ( 'NONE', *, *, #77872, .T. ) ; +#42575 = AXIS2_PLACEMENT_3D ( 'NONE', #97649, #73708, #66540 ) ; +#42576 = SURFACE_SIDE_STYLE ('',( #11330 ) ) ; +#42577 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42578 = ADVANCED_FACE ( 'NONE', ( #35570 ), #19716, .T. ) ; +#42579 = FILL_AREA_STYLE ('',( #3763 ) ) ; +#42580 = CARTESIAN_POINT ( 'NONE', ( 1.688590486522010048, -1.445336647901250160, 0.8099999999999976108 ) ) ; +#42581 = CARTESIAN_POINT ( 'NONE', ( -0.2413611859056800091, -1.318798174699070014, 0.8100000000000000533 ) ) ; +#42582 = CARTESIAN_POINT ( 'NONE', ( 0.2732652112985429760, -1.367023653493709912, 0.8100000000000000533 ) ) ; +#42583 = SURFACE_STYLE_FILL_AREA ( #66060 ) ; +#42584 = EDGE_LOOP ( 'NONE', ( #32973, #54671, #69873, #63614 ) ) ; +#42585 = CARTESIAN_POINT ( 'NONE', ( 1.993397459621554901, 1.600000000000000089, -11.36999999999999922 ) ) ; +#42586 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#42587 = CARTESIAN_POINT ( 'NONE', ( 2.616666666666666252, 3.099999999999960121, 0.000000000000000000 ) ) ; +#42588 = CARTESIAN_POINT ( 'NONE', ( -2.276179938779915091, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#42589 = PLANE ( 'NONE', #8982 ) ; +#42590 = SURFACE_STYLE_FILL_AREA ( #25773 ) ; +#42591 = SURFACE_STYLE_FILL_AREA ( #36441 ) ; +#42592 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#42593 = LINE ( 'NONE', #42093, #57873 ) ; +#42594 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42596 = EDGE_CURVE ( 'NONE', #45346, #78683, #42213, .T. ) ; +#42595 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34456 ) ) ; +#42597 = CARTESIAN_POINT ( 'NONE', ( 6.678959499500000341, 8.385468500500000033, 0.8991599999999999593 ) ) ; +#42598 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42599 = EDGE_LOOP ( 'NONE', ( #68377, #46142, #35988, #55487, #45038 ) ) ; +#42600 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42601 = ORIENTED_EDGE ( 'NONE', *, *, #88594, .F. ) ; +#42602 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42603 = FILL_AREA_STYLE ('',( #1410 ) ) ; +#42604 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#42605 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#42606 = PRESENTATION_STYLE_ASSIGNMENT (( #80927 ) ) ; +#42607 = PLANE ( 'NONE', #389 ) ; +#42608 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42609 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#42610 = PRESENTATION_STYLE_ASSIGNMENT (( #89577 ) ) ; +#42611 = ORIENTED_EDGE ( 'NONE', *, *, #69836, .F. ) ; +#42612 = EDGE_CURVE ( 'NONE', #69995, #56700, #98247, .T. ) ; +#42613 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8991599999999999593 ) ) ; +#42614 = ADVANCED_FACE ( 'NONE', ( #90146 ), #20201, .T. ) ; +#42615 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42616 = SURFACE_SIDE_STYLE ('',( #20112 ) ) ; +#42617 = ORIENTED_EDGE ( 'NONE', *, *, #96170, .F. ) ; +#42618 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42619 = SURFACE_STYLE_FILL_AREA ( #58980 ) ; +#42620 = CIRCLE ( 'NONE', #27917, 0.1099999999999998479 ) ; +#42621 = SURFACE_SIDE_STYLE ('',( #17595 ) ) ; +#42622 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60565 ) ) ; +#42623 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#42624 = CARTESIAN_POINT ( 'NONE', ( -1.158596477595430052, -1.445196667902379994, 0.8100000000000000533 ) ) ; +#42625 = SURFACE_SIDE_STYLE ('',( #3319 ) ) ; +#42626 = ORIENTED_EDGE ( 'NONE', *, *, #40068, .T. ) ; +#42627 = FILL_AREA_STYLE ('',( #26315 ) ) ; +#42628 = AXIS2_PLACEMENT_3D ( 'NONE', #38281, #77074, #7037 ) ; +#42629 = SURFACE_STYLE_USAGE ( .BOTH. , #67096 ) ; +#42630 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11552 ) ) ; +#42631 = ADVANCED_FACE ( 'NONE', ( #36564 ), #45169, .T. ) ; +#42632 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42633 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41050 ), #52475 ) ; +#42634 = ORIENTED_EDGE ( 'NONE', *, *, #84853, .T. ) ; +#42635 = EDGE_CURVE ( 'NONE', #76681, #34634, #83517, .T. ) ; +#42636 = CARTESIAN_POINT ( 'NONE', ( 2.183333333333333570, -3.099999999999969891, 0.000000000000000000 ) ) ; +#42637 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, 0.000000000000000000 ) ) ; +#42638 = SURFACE_STYLE_USAGE ( .BOTH. , #35999 ) ; +#42640 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42639 = SURFACE_STYLE_USAGE ( .BOTH. , #91100 ) ; +#42641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50825 ), #18101 ) ; +#42642 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#42643 = VERTEX_POINT ( 'NONE', #68159 ) ; +#42644 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#42645 = ADVANCED_FACE ( 'NONE', ( #98738 ), #69665, .F. ) ; +#42646 = VECTOR ( 'NONE', #92203, 1000.000000000000000 ) ; +#42647 = ADVANCED_FACE ( 'NONE', ( #47210 ), #17061, .T. ) ; +#42648 = VECTOR ( 'NONE', #83960, 1000.000000000000000 ) ; +#42649 = ORIENTED_EDGE ( 'NONE', *, *, #71781, .F. ) ; +#42650 = ORIENTED_EDGE ( 'NONE', *, *, #15291, .T. ) ; +#42651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75867, 'distance_accuracy_value', 'NONE'); +#42652 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#42653 = LINE ( 'NONE', #51328, #4038 ) ; +#42654 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#42655 = SURFACE_STYLE_USAGE ( .BOTH. , #50355 ) ; +#42656 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.000000000000000000 ) ) ; +#42657 = ORIENTED_EDGE ( 'NONE', *, *, #64841, .T. ) ; +#42658 = PRESENTATION_STYLE_ASSIGNMENT (( #88602 ) ) ; +#42659 = SURFACE_STYLE_FILL_AREA ( #14339 ) ; +#42660 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42661 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#42662 = VECTOR ( 'NONE', #17568, 1000.000000000000000 ) ; +#42663 = VERTEX_POINT ( 'NONE', #9338 ) ; +#42665 = LINE ( 'NONE', #41668, #95895 ) ; +#42664 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000005884, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#42666 = ORIENTED_EDGE ( 'NONE', *, *, #45662, .T. ) ; +#42667 = VECTOR ( 'NONE', #44733, 1000.000000000000000 ) ; +#42669 = CARTESIAN_POINT ( 'NONE', ( -0.4373985389610389740, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#42668 = CARTESIAN_POINT ( 'NONE', ( 0.1885535017837845218, -1.364480372126009255, 0.8100000000000000533 ) ) ; +#42670 = EDGE_CURVE ( 'NONE', #21841, #92928, #59813, .T. ) ; +#42671 = SURFACE_STYLE_FILL_AREA ( #32994 ) ; +#42673 = ORIENTED_EDGE ( 'NONE', *, *, #45440, .F. ) ; +#42672 = VECTOR ( 'NONE', #92564, 1000.000000000000000 ) ; +#42674 = SURFACE_SIDE_STYLE ('',( #36033 ) ) ; +#42675 = ORIENTED_EDGE ( 'NONE', *, *, #46732, .T. ) ; +#42676 = CARTESIAN_POINT ( 'NONE', ( 1.291611456110860034, -1.433733517242619993, 0.8299999999999999600 ) ) ; +#42677 = VERTEX_POINT ( 'NONE', #1783 ) ; +#42678 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42680 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#42679 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42681 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#42682 = EDGE_CURVE ( 'NONE', #27262, #40037, #97536, .T. ) ; +#42683 = CONICAL_SURFACE ( 'NONE', #62296, 0.6999999999948158802, 0.4636476090008060935 ) ; +#42684 = EDGE_CURVE ( 'NONE', #36325, #49721, #95151, .T. ) ; +#42685 = LINE ( 'NONE', #66160, #76866 ) ; +#42686 = STYLED_ITEM ( 'NONE', ( #98713 ), #86888 ) ; +#42687 = VERTEX_POINT ( 'NONE', #47723 ) ; +#42688 = CARTESIAN_POINT ( 'NONE', ( 1.343121150739609915, -1.400043273498609908, 0.8299999999999994049 ) ) ; +#42689 = EDGE_CURVE ( 'NONE', #69488, #52058, #93627, .T. ) ; +#42691 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#42690 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8648700000000000276 ) ) ; +#42693 = PLANE ( 'NONE', #61317 ) ; +#42692 = VECTOR ( 'NONE', #81965, 1000.000000000000000 ) ; +#42694 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70883, 'distance_accuracy_value', 'NONE'); +#42695 = SURFACE_STYLE_FILL_AREA ( #11452 ) ; +#42696 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42697 = LINE ( 'NONE', #21212, #64731 ) ; +#42698 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42699 = ORIENTED_EDGE ( 'NONE', *, *, #100102, .T. ) ; +#42700 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86714 ) ) ; +#42701 = FILL_AREA_STYLE ('',( #49882 ) ) ; +#42702 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42703 = SURFACE_SIDE_STYLE ('',( #97776 ) ) ; +#42704 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.05000000000000001665, 0.2100000000000000200 ) ) ; +#42705 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3290 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70448, #38822, #23009 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42706 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.383333333333320425, 0.000000000000000000 ) ) ; +#42707 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#42708 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000222, 0.1200000000000000927, 0.4000000000000000222 ) ) ; +#42709 = SURFACE_STYLE_FILL_AREA ( #74855 ) ; +#42710 = ADVANCED_FACE ( 'NONE', ( #17552 ), #56428, .T. ) ; +#42711 = FILL_AREA_STYLE_COLOUR ( '', #11519 ) ; +#42712 = CIRCLE ( 'NONE', #96462, 1.383445513478990030 ) ; +#42713 = SURFACE_STYLE_USAGE ( .BOTH. , #43201 ) ; +#42714 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#42715 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8648700000000000276 ) ) ; +#42716 = VECTOR ( 'NONE', #70522, 1000.000000000000000 ) ; +#42717 = EDGE_CURVE ( 'NONE', #57747, #32802, #27784, .T. ) ; +#42718 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#42719 = CARTESIAN_POINT ( 'NONE', ( 1.794978790831629922, -1.096743473147149928, 0.8299999999999997380 ) ) ; +#42720 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83464 ) ) ; +#42721 = FACE_OUTER_BOUND ( 'NONE', #22634, .T. ) ; +#42722 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42723 = VERTEX_POINT ( 'NONE', #81415 ) ; +#42724 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#42725 = SURFACE_STYLE_FILL_AREA ( #28413 ) ; +#42726 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 11.25335600000000014, 0.8648700000000000276 ) ) ; +#42727 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59587, #80522, #53379, #29392 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42728 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42729 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42730 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42731 = EDGE_CURVE ( 'NONE', #26194, #62000, #57416, .T. ) ; +#42732 = AXIS2_PLACEMENT_3D ( 'NONE', #43399, #2601, #34267 ) ; +#42733 = PRESENTATION_STYLE_ASSIGNMENT (( #2430 ) ) ; +#42734 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660784, -1.070941558441560026, 0.8100000000000001643 ) ) ; +#42735 = ORIENTED_EDGE ( 'NONE', *, *, #33531, .F. ) ; +#42736 = FACE_OUTER_BOUND ( 'NONE', #65387, .T. ) ; +#42737 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42738 = VECTOR ( 'NONE', #83074, 1000.000000000000114 ) ; +#42739 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#42740 = FACE_OUTER_BOUND ( 'NONE', #4716, .T. ) ; +#42741 = PLANE ( 'NONE', #2219 ) ; +#42742 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42743 = FILL_AREA_STYLE_COLOUR ( '', #89307 ) ; +#42744 = EDGE_LOOP ( 'NONE', ( #4287, #83414, #41475, #6414 ) ) ; +#42745 = ORIENTED_EDGE ( 'NONE', *, *, #40693, .T. ) ; +#42746 = STYLED_ITEM ( 'NONE', ( #17669 ), #18489 ) ; +#42747 = AXIS2_PLACEMENT_3D ( 'NONE', #64727, #9008, #47394 ) ; +#42748 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, -11.36999999999999922 ) ) ; +#42749 = ORIENTED_EDGE ( 'NONE', *, *, #78859, .T. ) ; +#42750 = CARTESIAN_POINT ( 'NONE', ( 1.724073170230389973, -1.220939016933670018, 0.8100000000000000533 ) ) ; +#42751 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42752 = VECTOR ( 'NONE', #51222, 1000.000000000000000 ) ; +#42753 = FILL_AREA_STYLE ('',( #90214 ) ) ; +#42754 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93207 ) ) ; +#42755 = CIRCLE ( 'NONE', #19866, 0.2000000000000000111 ) ; +#42756 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42757 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #583, #22154 ) ; +#42758 = FILL_AREA_STYLE_COLOUR ( '', #83555 ) ; +#42760 = ORIENTED_EDGE ( 'NONE', *, *, #96967, .F. ) ; +#42759 = ORIENTED_EDGE ( 'NONE', *, *, #63939, .F. ) ; +#42761 = ADVANCED_FACE ( 'NONE', ( #18048 ), #72715, .T. ) ; +#42762 = VECTOR ( 'NONE', #61498, 1000.000000000000000 ) ; +#42763 = ORIENTED_EDGE ( 'NONE', *, *, #83549, .T. ) ; +#42764 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67235 ), #28128 ) ; +#42765 = VERTEX_POINT ( 'NONE', #20081 ) ; +#42766 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8743, 'distance_accuracy_value', 'NONE'); +#42767 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42768 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#42769 = VERTEX_POINT ( 'NONE', #10844 ) ; +#42770 = EDGE_CURVE ( 'NONE', #16993, #44609, #81671, .T. ) ; +#42771 = VECTOR ( 'NONE', #37293, 1000.000000000000000 ) ; +#42772 = FILL_AREA_STYLE ('',( #66258 ) ) ; +#42773 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#42774 = CARTESIAN_POINT ( 'NONE', ( -1.319753185035670073, -0.9379159637996590249, 0.8100000000000000533 ) ) ; +#42775 = AXIS2_PLACEMENT_3D ( 'NONE', #66698, #27416, #67203 ) ; +#42776 = EDGE_LOOP ( 'NONE', ( #30542, #79652, #34507, #53758 ) ) ; +#42778 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42777 = FACE_OUTER_BOUND ( 'NONE', #13374, .T. ) ; +#42779 = ORIENTED_EDGE ( 'NONE', *, *, #32854, .F. ) ; +#42780 = ORIENTED_EDGE ( 'NONE', *, *, #98521, .F. ) ; +#42781 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2042 ) ) ; +#42783 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42784 = EDGE_CURVE ( 'NONE', #81337, #82955, #63517, .T. ) ; +#42785 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#42786 = VECTOR ( 'NONE', #62387, 1000.000000000000114 ) ; +#42788 = ORIENTED_EDGE ( 'NONE', *, *, #82513, .T. ) ; +#42787 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.01000000000000000021, -1.250000000000000000 ) ) ; +#42789 = SURFACE_STYLE_FILL_AREA ( #19808 ) ; +#42790 = ORIENTED_EDGE ( 'NONE', *, *, #45209, .F. ) ; +#42791 = CARTESIAN_POINT ( 'NONE', ( -0.2758995662929830117, -0.9966931238414048488, 0.8100000000000000533 ) ) ; +#42792 = ORIENTED_EDGE ( 'NONE', *, *, #3659, .F. ) ; +#42793 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#42794 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#42796 = VERTEX_POINT ( 'NONE', #57939 ) ; +#42795 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7085 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93423, #70469, #14295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42797 = ORIENTED_EDGE ( 'NONE', *, *, #30200, .F. ) ; +#42799 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#42798 = LINE ( 'NONE', #21311, #45574 ) ; +#42800 = EDGE_CURVE ( 'NONE', #38179, #81759, #88538, .T. ) ; +#42801 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42802 = AXIS2_PLACEMENT_3D ( 'NONE', #87033, #41582, #2772 ) ; +#42803 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42804 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42806 = VECTOR ( 'NONE', #61265, 1000.000000000000000 ) ; +#42805 = LINE ( 'NONE', #81129, #95116 ) ; +#42807 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8648700000000000276 ) ) ; +#42808 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7936, 'distance_accuracy_value', 'NONE'); +#42809 = ORIENTED_EDGE ( 'NONE', *, *, #95883, .F. ) ; +#42810 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95423, #56175, #10592, #72991 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#42811 = SURFACE_STYLE_FILL_AREA ( #60179 ) ; +#42812 = EDGE_LOOP ( 'NONE', ( #8106, #62029, #61091, #24823 ) ) ; +#42813 = EDGE_CURVE ( 'NONE', #78572, #18155, #56924, .T. ) ; +#42814 = LINE ( 'NONE', #18289, #22816 ) ; +#42815 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#42816 = CARTESIAN_POINT ( 'NONE', ( 1.164415487177949959, -1.144973971495400145, 0.8299999999999999600 ) ) ; +#42817 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42818 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42819 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42820 = LINE ( 'NONE', #97403, #32444 ) ; +#42821 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01499999999999999944, -0.1400000000000000133 ) ) ; +#42822 = SURFACE_STYLE_FILL_AREA ( #4014 ) ; +#42823 = ORIENTED_EDGE ( 'NONE', *, *, #65169, .F. ) ; +#42824 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -11.27000000000000135 ) ) ; +#42825 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42826 = VECTOR ( 'NONE', #56487, 1000.000000000000000 ) ; +#42828 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86846 ) ) ; +#42827 = CARTESIAN_POINT ( 'NONE', ( 0.1720843054334539879, -1.066823530734400061, 0.8299999999999999600 ) ) ; +#42829 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73802 ), #83646 ) ; +#42830 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42831 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#42832 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42833 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#42834 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68018, 'distance_accuracy_value', 'NONE'); +#42836 = ADVANCED_FACE ( 'NONE', ( #80906 ), #34939, .T. ) ; +#42835 = VECTOR ( 'NONE', #37911, 1000.000000000000114 ) ; +#42837 = EDGE_CURVE ( 'NONE', #45275, #98628, #68032, .T. ) ; +#42838 = VECTOR ( 'NONE', #45075, 1000.000000000000000 ) ; +#42839 = PRESENTATION_STYLE_ASSIGNMENT (( #19848 ) ) ; +#42840 = AXIS2_PLACEMENT_3D ( 'NONE', #68495, #93955, #93463 ) ; +#42841 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#42842 = EDGE_CURVE ( 'NONE', #18334, #33857, #67053, .T. ) ; +#42843 = AXIS2_PLACEMENT_3D ( 'NONE', #53004, #22335, #75967 ) ; +#42844 = EDGE_CURVE ( 'NONE', #98326, #84669, #5223, .T. ) ; +#42845 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38592 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11411, #3835, #22674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42846 = ORIENTED_EDGE ( 'NONE', *, *, #12914, .T. ) ; +#42847 = PLANE ( 'NONE', #91633 ) ; +#42848 = CARTESIAN_POINT ( 'NONE', ( 1.512782233897560058, -1.071137013546419992, 0.8299999999999999600 ) ) ; +#42849 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#42850 = EDGE_LOOP ( 'NONE', ( #32229, #94124, #72613, #80067 ) ) ; +#42851 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#42852 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#42853 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42854 = SURFACE_SIDE_STYLE ('',( #99379 ) ) ; +#42855 = ADVANCED_FACE ( 'NONE', ( #99605 ), #51760, .F. ) ; +#42856 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11358 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17964, #87433, #2686 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#42857 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.699999999999999734, 0.1829999999999999960 ) ) ; +#42858 = CARTESIAN_POINT ( 'NONE', ( 1.769936080281629964, -0.9872600217210630857, 0.8100000000000006084 ) ) ; +#42859 = ADVANCED_FACE ( 'NONE', ( #20583 ), #28747, .T. ) ; +#42860 = FILL_AREA_STYLE ('',( #42365 ) ) ; +#42861 = VERTEX_POINT ( 'NONE', #61928 ) ; +#42862 = ORIENTED_EDGE ( 'NONE', *, *, #96109, .T. ) ; +#42863 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42864 = FILL_AREA_STYLE_COLOUR ( '', #67614 ) ; +#42865 = LINE ( 'NONE', #33193, #53134 ) ; +#42866 = PRESENTATION_STYLE_ASSIGNMENT (( #10606 ) ) ; +#42867 = SURFACE_STYLE_FILL_AREA ( #58715 ) ; +#42868 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#42869 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42870 = EDGE_LOOP ( 'NONE', ( #63794, #48536, #11248, #8597 ) ) ; +#42871 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#42872 = ORIENTED_EDGE ( 'NONE', *, *, #35091, .F. ) ; +#42873 = PRESENTATION_STYLE_ASSIGNMENT (( #147 ) ) ; +#42874 = VECTOR ( 'NONE', #23829, 1000.000000000000000 ) ; +#42875 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41292 ), #24974 ) ; +#42876 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 15.15000000000000036, 0.000000000000000000 ) ) ; +#42877 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#42878 = CARTESIAN_POINT ( 'NONE', ( -1.024611994374110102, -1.021599245672099920, 0.8100000000000000533 ) ) ; +#42879 = CARTESIAN_POINT ( 'NONE', ( -0.3840663679600159752, -0.9878352835667890686, 0.8299999999999999600 ) ) ; +#42880 = CARTESIAN_POINT ( 'NONE', ( -0.5631367483934444085, 1.338969331779750860, 0.8100000000000003864 ) ) ; +#42882 = ORIENTED_EDGE ( 'NONE', *, *, #80661, .T. ) ; +#42881 = VERTEX_POINT ( 'NONE', #32286 ) ; +#42883 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42884 = VERTEX_POINT ( 'NONE', #1653 ) ; +#42885 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#42886 = STYLED_ITEM ( 'NONE', ( #11960 ), #19433 ) ; +#42887 = VECTOR ( 'NONE', #12234, 1000.000000000000000 ) ; +#42888 = SURFACE_STYLE_FILL_AREA ( #98925 ) ; +#42889 = VERTEX_POINT ( 'NONE', #62945 ) ; +#42890 = EDGE_CURVE ( 'NONE', #83734, #36325, #85889, .T. ) ; +#42891 = ORIENTED_EDGE ( 'NONE', *, *, #100222, .F. ) ; +#42892 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39678 ), #93425 ) ; +#42893 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86921 ) ) ; +#42894 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3750 ), #73880 ) ; +#42895 = PRESENTATION_STYLE_ASSIGNMENT (( #35271 ) ) ; +#42896 = FILL_AREA_STYLE_COLOUR ( '', #47053 ) ; +#42897 = LINE ( 'NONE', #41409, #28675 ) ; +#42898 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42899 = ORIENTED_EDGE ( 'NONE', *, *, #80787, .T. ) ; +#42900 = ORIENTED_EDGE ( 'NONE', *, *, #50718, .T. ) ; +#42901 = VECTOR ( 'NONE', #31113, 1000.000000000000000 ) ; +#42902 = EDGE_LOOP ( 'NONE', ( #48936, #16880, #88557, #23451 ) ) ; +#42903 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42904 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#42905 = VECTOR ( 'NONE', #19497, 1000.000000000000000 ) ; +#42906 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42908 = ORIENTED_EDGE ( 'NONE', *, *, #93213, .T. ) ; +#42907 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#42909 = ORIENTED_EDGE ( 'NONE', *, *, #43902, .F. ) ; +#42910 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#42911 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#42912 = EDGE_LOOP ( 'NONE', ( #48322, #68992, #31291, #94585 ) ) ; +#42913 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42914 = EDGE_CURVE ( 'NONE', #67142, #12514, #40460, .T. ) ; +#42915 = ORIENTED_EDGE ( 'NONE', *, *, #12533, .F. ) ; +#42916 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#42917 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8100000000000001643 ) ) ; +#42918 = CARTESIAN_POINT ( 'NONE', ( -1.005723260889149984, -1.285676881280640282, 0.8300000000000000711 ) ) ; +#42919 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42921 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#42920 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42922 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#42923 = ORIENTED_EDGE ( 'NONE', *, *, #37563, .F. ) ; +#42924 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#42925 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42926 = ORIENTED_EDGE ( 'NONE', *, *, #72868, .F. ) ; +#42927 = LINE ( 'NONE', #4128, #10748 ) ; +#42928 = CARTESIAN_POINT ( 'NONE', ( -0.3725126731206029884, -1.137476252684360034, 0.8300000000000000711 ) ) ; +#42929 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72666, #40017, #94090, #86476, #17511, #16488, #9289, #72169, #47670, #18004, #71155, #2233, #63017, #55372, #24218, #87989, #54851, #25717, #79327 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.282253461522702383E-05, 2.507919025753242381E-05, 3.701293588743341192E-05, 4.881751796654575001E-05, 6.034298060293846879E-05, 7.160834540111348206E-05, 8.290735754414939567E-05, 9.419732065135351157E-05, 0.0001056043613177938274, 0.0001170433563318540895, 0.0001288782026606012405, 0.0001410409865858876027, 0.0001533564673829372572, 0.0001657975684503316179, 0.0001783275440079054976, 0.0001911449535952143195 ), + .UNSPECIFIED. ) ; +#42930 = SURFACE_SIDE_STYLE ('',( #65927 ) ) ; +#42931 = CARTESIAN_POINT ( 'NONE', ( 8.969985124875011095, 9.983529124875014205, 0.8991599999999999593 ) ) ; +#42932 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.699999999999999734, 9.720630125846873012E-79 ) ) ; +#42933 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#42934 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#42935 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42936 = STYLED_ITEM ( 'NONE', ( #81172 ), #47382 ) ; +#42937 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#42938 = ORIENTED_EDGE ( 'NONE', *, *, #27877, .T. ) ; +#42939 = LINE ( 'NONE', #65942, #22763 ) ; +#42942 = SURFACE_SIDE_STYLE ('',( #35329 ) ) ; +#42941 = DIRECTION ( 'NONE', ( -0.7071075504167442238, 0.7071060119555140355, 0.000000000000000000 ) ) ; +#42940 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18439 ) ) ; +#42943 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42944 = LINE ( 'NONE', #4147, #61548 ) ; +#42945 = EDGE_CURVE ( 'NONE', #62776, #54674, #18317, .T. ) ; +#42946 = AXIS2_PLACEMENT_3D ( 'NONE', #32407, #24777, #1781 ) ; +#42948 = ORIENTED_EDGE ( 'NONE', *, *, #96416, .T. ) ; +#42947 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#42949 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#42950 = SURFACE_STYLE_USAGE ( .BOTH. , #88416 ) ; +#42951 = CARTESIAN_POINT ( 'NONE', ( 2.183333333333333570, 3.099999999999969891, 0.000000000000000000 ) ) ; +#42952 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#42953 = VECTOR ( 'NONE', #5284, 1000.000000000000000 ) ; +#42954 = FILL_AREA_STYLE_COLOUR ( '', #50331 ) ; +#42955 = STYLED_ITEM ( 'NONE', ( #67411 ), #19030 ) ; +#42956 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#42957 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261924000000000046, 0.8991599999999999593 ) ) ; +#42958 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#42959 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#42960 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000007688, -3.149999999999979927, 0.000000000000000000 ) ) ; +#42961 = EDGE_CURVE ( 'NONE', #11614, #50012, #23610, .T. ) ; +#42962 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70653 ) ) ; +#42963 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#42964 = ORIENTED_EDGE ( 'NONE', *, *, #59662, .F. ) ; +#42966 = ORIENTED_EDGE ( 'NONE', *, *, #3525, .F. ) ; +#42965 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63968 ) ) ; +#42967 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#42968 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37079, 'distance_accuracy_value', 'NONE'); +#42969 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36804, 'distance_accuracy_value', 'NONE'); +#42970 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36506 ), #20141 ) ; +#42971 = FACE_OUTER_BOUND ( 'NONE', #78898, .T. ) ; +#42972 = CARTESIAN_POINT ( 'NONE', ( -0.2258383435392919969, -1.079063990458370093, 0.8100000000000000533 ) ) ; +#42973 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42974 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#42975 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33146 ) ) ; +#42976 = LINE ( 'NONE', #26681, #11705 ) ; +#42977 = FACE_OUTER_BOUND ( 'NONE', #4951, .T. ) ; +#42978 = SURFACE_SIDE_STYLE ('',( #21009 ) ) ; +#42979 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#42980 = VERTEX_POINT ( 'NONE', #39418 ) ; +#42981 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#42982 = PLANE ( 'NONE', #18348 ) ; +#42983 = ORIENTED_EDGE ( 'NONE', *, *, #80908, .F. ) ; +#42984 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #550, #25584, #8132, #32225, #72038, #39354, #24075, #33235, #47023, #80215, #63397, #47528, #55226, #86332, #10135, #55722, #16861, #79189, #41406 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.382712307325913055E-05, 2.683571007987539184E-05, 3.927008175207144996E-05, 5.133161887827227877E-05, 6.299521226121080773E-05, 7.429237845692839319E-05, 8.536174655250704062E-05, 9.652160775091320026E-05, 0.0001077490236025280414, 0.0001190364376891027789, 0.0001307000310720414840, 0.0001426938147905762336, 0.0001549197910463071513, 0.0001672110464362108154, 0.0001797629478635001232, 0.0001926125413639734438 ), + .UNSPECIFIED. ) ; +#42985 = PLANE ( 'NONE', #71830 ) ; +#42986 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#42987 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42988 = ORIENTED_EDGE ( 'NONE', *, *, #10547, .T. ) ; +#42989 = SURFACE_STYLE_USAGE ( .BOTH. , #72134 ) ; +#42990 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.627715291671302177E-18, 0.6500000000000001332 ) ) ; +#42991 = EDGE_CURVE ( 'NONE', #88747, #63404, #71597, .T. ) ; +#42992 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.383333333333323090, 0.000000000000000000 ) ) ; +#42994 = VERTEX_POINT ( 'NONE', #7688 ) ; +#42993 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29927 ), #46225 ) ; +#42995 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#42996 = SURFACE_STYLE_USAGE ( .BOTH. , #9762 ) ; +#42997 = ORIENTED_EDGE ( 'NONE', *, *, #57582, .T. ) ; +#42998 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#42999 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13620 ), #64220 ) ; +#43000 = FILL_AREA_STYLE_COLOUR ( '', #70262 ) ; +#43001 = VERTEX_POINT ( 'NONE', #615 ) ; +#43002 = EDGE_CURVE ( 'NONE', #13072, #71662, #8696, .T. ) ; +#43003 = VERTEX_POINT ( 'NONE', #9214 ) ; +#43004 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#43005 = PRESENTATION_STYLE_ASSIGNMENT (( #65476 ) ) ; +#43006 = FILL_AREA_STYLE ('',( #50706 ) ) ; +#43007 = ORIENTED_EDGE ( 'NONE', *, *, #95594, .F. ) ; +#43009 = ORIENTED_EDGE ( 'NONE', *, *, #80286, .F. ) ; +#43008 = EDGE_LOOP ( 'NONE', ( #92004, #51197, #19818, #13461 ) ) ; +#43010 = PRESENTATION_STYLE_ASSIGNMENT (( #89975 ) ) ; +#43011 = VERTEX_POINT ( 'NONE', #7187 ) ; +#43012 = ORIENTED_EDGE ( 'NONE', *, *, #3850, .F. ) ; +#43013 = ORIENTED_EDGE ( 'NONE', *, *, #60391, .T. ) ; +#43014 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43016 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#43015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34818 ), #25057 ) ; +#43017 = FILL_AREA_STYLE ('',( #58389 ) ) ; +#43018 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43019 = ORIENTED_EDGE ( 'NONE', *, *, #34442, .F. ) ; +#43020 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#43021 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26803 ) ) ; +#43022 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#43023 = ORIENTED_EDGE ( 'NONE', *, *, #99397, .T. ) ; +#43024 = SURFACE_STYLE_USAGE ( .BOTH. , #42040 ) ; +#43025 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43027 = VECTOR ( 'NONE', #29858, 1000.000000000000000 ) ; +#43026 = VECTOR ( 'NONE', #66000, 1000.000000000000000 ) ; +#43028 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100918 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55650, #38302, #73969 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43029 = SURFACE_STYLE_USAGE ( .BOTH. , #19034 ) ; +#43030 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#43031 = CARTESIAN_POINT ( 'NONE', ( -1.296446609406726180, 0.7099999999999999645, 1.050000000000000266 ) ) ; +#43032 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43033 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43034 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43035 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43036 = CARTESIAN_POINT ( 'NONE', ( 1.706409873422509937, -1.445184491613219935, 0.8299999999999999600 ) ) ; +#43037 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43038 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43039 = FILL_AREA_STYLE_COLOUR ( '', #89636 ) ; +#43040 = ORIENTED_EDGE ( 'NONE', *, *, #10675, .F. ) ; +#43041 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70807 ) ) ; +#43042 = FILL_AREA_STYLE_COLOUR ( '', #51702 ) ; +#43043 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4808578643762690397, -0.2434314575050762208 ) ) ; +#43044 = LINE ( 'NONE', #36408, #82758 ) ; +#43045 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#43046 = FACE_OUTER_BOUND ( 'NONE', #57485, .T. ) ; +#43047 = EDGE_CURVE ( 'NONE', #93316, #87607, #25162, .T. ) ; +#43048 = SURFACE_SIDE_STYLE ('',( #87501 ) ) ; +#43049 = EDGE_CURVE ( 'NONE', #83732, #21812, #63457, .T. ) ; +#43050 = AXIS2_PLACEMENT_3D ( 'NONE', #57222, #57735, #16327 ) ; +#43051 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43052 = CARTESIAN_POINT ( 'NONE', ( 1.190985675097830265, -0.8845231535185279492, 0.8299999999999999600 ) ) ; +#43053 = ORIENTED_EDGE ( 'NONE', *, *, #76397, .F. ) ; +#43054 = CARTESIAN_POINT ( 'NONE', ( -1.171237681315639989, -1.515071875619850017, 0.8300000000000024025 ) ) ; +#43055 = CONICAL_SURFACE ( 'NONE', #11997, 0.2299999998740531737, 0.7853981633974482790 ) ; +#43056 = FILL_AREA_STYLE ('',( #88525 ) ) ; +#43057 = VERTEX_POINT ( 'NONE', #31768 ) ; +#43058 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#43059 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43060 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17027 ), #67524 ) ; +#43062 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43061 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#43063 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43064 = LINE ( 'NONE', #58937, #94184 ) ; +#43065 = SURFACE_STYLE_FILL_AREA ( #36921 ) ; +#43066 = EDGE_CURVE ( 'NONE', #69132, #56583, #94004, .T. ) ; +#43067 = FILL_AREA_STYLE ('',( #81412 ) ) ; +#43068 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43069 = ORIENTED_EDGE ( 'NONE', *, *, #7497, .T. ) ; +#43070 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.4245906043549200204, -0.01999999999999999695 ) ) ; +#43071 = VECTOR ( 'NONE', #61305, 1000.000000000000000 ) ; +#43072 = VECTOR ( 'NONE', #21340, 1000.000000000000000 ) ; +#43073 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43074 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#43075 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#43076 = LINE ( 'NONE', #99122, #11493 ) ; +#43077 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43078 = STYLED_ITEM ( 'NONE', ( #55689 ), #48119 ) ; +#43079 = STYLED_ITEM ( 'NONE', ( #63253 ), #26556 ) ; +#43080 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43081 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97877, 'distance_accuracy_value', 'NONE'); +#43082 = EDGE_CURVE ( 'NONE', #73465, #7518, #32784, .T. ) ; +#43083 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43084 = STYLED_ITEM ( 'NONE', ( #67643 ), #76696 ) ; +#43085 = SURFACE_SIDE_STYLE ('',( #82419 ) ) ; +#43086 = VERTEX_POINT ( 'NONE', #15921 ) ; +#43087 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99810 ), #91977 ) ; +#43088 = ORIENTED_EDGE ( 'NONE', *, *, #39082, .F. ) ; +#43089 = PLANE ( 'NONE', #7664 ) ; +#43090 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19130, 'distance_accuracy_value', 'NONE'); +#43091 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69584, 'distance_accuracy_value', 'NONE'); +#43092 = CARTESIAN_POINT ( 'NONE', ( 8.231457000000000690, 10.67649499999999918, 0.8648700000000000276 ) ) ; +#43093 = PLANE ( 'NONE', #85624 ) ; +#43094 = CARTESIAN_POINT ( 'NONE', ( -1.219664229900655039, -1.514066480758919697, 0.8099999999996092548 ) ) ; +#43095 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, 0.000000000000000000 ) ) ; +#43096 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43097 = CARTESIAN_POINT ( 'NONE', ( 1.877768173756620085, -1.057175192472970204, 0.8100000000000000533 ) ) ; +#43098 = LINE ( 'NONE', #74253, #1114 ) ; +#43099 = VECTOR ( 'NONE', #11226, 1000.000000000000000 ) ; +#43100 = FACE_OUTER_BOUND ( 'NONE', #72046, .T. ) ; +#43101 = EDGE_LOOP ( 'NONE', ( #19444, #81166, #93797, #24175 ) ) ; +#43102 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#43103 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#43104 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46418, 'distance_accuracy_value', 'NONE'); +#43107 = VECTOR ( 'NONE', #89547, 1000.000000000000000 ) ; +#43106 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43105 = PLANE ( 'NONE', #1985 ) ; +#43108 = VECTOR ( 'NONE', #71965, 1000.000000000000000 ) ; +#43109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43110 = ORIENTED_EDGE ( 'NONE', *, *, #33008, .T. ) ; +#43111 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43112 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.000000000000000000 ) ) ; +#43113 = ADVANCED_FACE ( 'NONE', ( #78250 ), #95031, .F. ) ; +#43114 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43115 = ORIENTED_EDGE ( 'NONE', *, *, #57592, .T. ) ; +#43116 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43117 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.383333333333326642, 0.000000000000000000 ) ) ; +#43118 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81440, 'distance_accuracy_value', 'NONE'); +#43119 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #685 ), #93569 ) ; +#43120 = FILL_AREA_STYLE ('',( #35993 ) ) ; +#43121 = SURFACE_STYLE_FILL_AREA ( #66112 ) ; +#43122 = ADVANCED_FACE ( 'NONE', ( #40969 ), #96546, .F. ) ; +#43123 = VERTEX_POINT ( 'NONE', #3650 ) ; +#43124 = CARTESIAN_POINT ( 'NONE', ( -0.4406617557324680190, 0.3469459166020285035, 0.8100000000000000533 ) ) ; +#43125 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43126 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41978 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50567, #27574, #52552 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43127 = SURFACE_STYLE_FILL_AREA ( #57478 ) ; +#43128 = SURFACE_STYLE_FILL_AREA ( #59995 ) ; +#43129 = FACE_OUTER_BOUND ( 'NONE', #14819, .T. ) ; +#43130 = ORIENTED_EDGE ( 'NONE', *, *, #16834, .T. ) ; +#43131 = VERTEX_POINT ( 'NONE', #2656 ) ; +#43132 = ORIENTED_EDGE ( 'NONE', *, *, #92318, .F. ) ; +#43133 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.5000000000000000000, -13.40000000000000036 ) ) ; +#43134 = VECTOR ( 'NONE', #92884, 1000.000000000000000 ) ; +#43135 = FILL_AREA_STYLE_COLOUR ( '', #63914 ) ; +#43136 = VECTOR ( 'NONE', #86761, 1000.000000000000000 ) ; +#43137 = SURFACE_STYLE_FILL_AREA ( #50834 ) ; +#43138 = CYLINDRICAL_SURFACE ( 'NONE', #3188, 0.009999999999999998473 ) ; +#43139 = SURFACE_SIDE_STYLE ('',( #11913 ) ) ; +#43140 = LINE ( 'NONE', #42166, #88342 ) ; +#43141 = ORIENTED_EDGE ( 'NONE', *, *, #30356, .T. ) ; +#43142 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#43143 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80714 ), #83888 ) ; +#43144 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67608 ), #20331 ) ; +#43145 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602299999999858, 0.8991599999999999593 ) ) ; +#43146 = ORIENTED_EDGE ( 'NONE', *, *, #33641, .T. ) ; +#43147 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#43148 = VERTEX_POINT ( 'NONE', #41464 ) ; +#43149 = STYLED_ITEM ( 'NONE', ( #25723 ), #26722 ) ; +#43150 = ADVANCED_FACE ( 'NONE', ( #80776 ), #3149, .F. ) ; +#43151 = EDGE_CURVE ( 'NONE', #20186, #92428, #37327, .T. ) ; +#43152 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43153 = PRESENTATION_STYLE_ASSIGNMENT (( #12940 ) ) ; +#43154 = VERTEX_POINT ( 'NONE', #68425 ) ; +#43155 = AXIS2_PLACEMENT_3D ( 'NONE', #32653, #63801, #58174 ) ; +#43156 = ORIENTED_EDGE ( 'NONE', *, *, #91324, .T. ) ; +#43157 = VERTEX_POINT ( 'NONE', #28151 ) ; +#43158 = AXIS2_PLACEMENT_3D ( 'NONE', #86288, #32686, #23011 ) ; +#43159 = FILL_AREA_STYLE ('',( #65150 ) ) ; +#43160 = CARTESIAN_POINT ( 'NONE', ( -1.371290353842550047, -1.066576130479129914, 0.8299999999999999600 ) ) ; +#43161 = EDGE_CURVE ( 'NONE', #77646, #79372, #42755, .T. ) ; +#43162 = LINE ( 'NONE', #4364, #31869 ) ; +#43163 = ADVANCED_FACE ( 'NONE', ( #6086 ), #66122, .F. ) ; +#43164 = VECTOR ( 'NONE', #53324, 1000.000000000000000 ) ; +#43165 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43166 = SURFACE_STYLE_USAGE ( .BOTH. , #20177 ) ; +#43167 = CARTESIAN_POINT ( 'NONE', ( 0.3332327486577990050, -1.242627591519610109, 0.8100000000000000533 ) ) ; +#43168 = SURFACE_STYLE_USAGE ( .BOTH. , #88632 ) ; +#43169 = DIRECTION ( 'NONE', ( -0.7071075504167430026, -0.7071060119555152568, 0.000000000000000000 ) ) ; +#43170 = FILL_AREA_STYLE_COLOUR ( '', #82880 ) ; +#43171 = STYLED_ITEM ( 'NONE', ( #10630 ), #97723 ) ; +#43172 = VERTEX_POINT ( 'NONE', #66932 ) ; +#43173 = LINE ( 'NONE', #11950, #98969 ) ; +#43174 = PLANE ( 'NONE', #92089 ) ; +#43177 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#43176 = SURFACE_SIDE_STYLE ('',( #66658 ) ) ; +#43175 = CARTESIAN_POINT ( 'NONE', ( -0.8360085490496081961, 1.033343808911651340, 0.8100000000000000533 ) ) ; +#43178 = LINE ( 'NONE', #20193, #94099 ) ; +#43179 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43181 = EDGE_CURVE ( 'NONE', #9173, #98768, #98007, .T. ) ; +#43180 = VECTOR ( 'NONE', #17407, 1000.000000000000000 ) ; +#43182 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43183 = ORIENTED_EDGE ( 'NONE', *, *, #78770, .T. ) ; +#43184 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#43186 = EDGE_CURVE ( 'NONE', #74943, #56777, #1016, .T. ) ; +#43185 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43187 = SURFACE_SIDE_STYLE ('',( #20203 ) ) ; +#43188 = FACE_OUTER_BOUND ( 'NONE', #82781, .T. ) ; +#43189 = FILL_AREA_STYLE_COLOUR ( '', #5448 ) ; +#43190 = VECTOR ( 'NONE', #66117, 1000.000000000000000 ) ; +#43191 = CARTESIAN_POINT ( 'NONE', ( 0.4579875826041610032, -1.125997481646370035, 0.8300000000000015143 ) ) ; +#43192 = FILL_AREA_STYLE_COLOUR ( '', #31089 ) ; +#43193 = AXIS2_PLACEMENT_3D ( 'NONE', #28709, #4718, #12819 ) ; +#43194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43195 = SURFACE_STYLE_USAGE ( .BOTH. , #92162 ) ; +#43196 = LINE ( 'NONE', #74361, #39749 ) ; +#43197 = PRESENTATION_STYLE_ASSIGNMENT (( #73859 ) ) ; +#43198 = FILL_AREA_STYLE_COLOUR ( '', #34592 ) ; +#43199 = EDGE_CURVE ( 'NONE', #35876, #11607, #36637, .T. ) ; +#43200 = LINE ( 'NONE', #67183, #89730 ) ; +#43201 = SURFACE_SIDE_STYLE ('',( #83528 ) ) ; +#43202 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#43203 = STYLED_ITEM ( 'NONE', ( #52830 ), #29514 ) ; +#43204 = EDGE_CURVE ( 'NONE', #24940, #42288, #54133, .T. ) ; +#43205 = FACE_OUTER_BOUND ( 'NONE', #37783, .T. ) ; +#43206 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#43207 = LINE ( 'NONE', #74371, #92967 ) ; +#43209 = SURFACE_STYLE_USAGE ( .BOTH. , #78493 ) ; +#43208 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66822, #34215, #59729, #97915 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43210 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28173, 'distance_accuracy_value', 'NONE'); +#43211 = SURFACE_SIDE_STYLE ('',( #20221 ) ) ; +#43212 = STYLED_ITEM ( 'NONE', ( #90819 ), #89626 ) ; +#43213 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69249 ) ) ; +#43214 = CARTESIAN_POINT ( 'NONE', ( -0.2957352054868390145, -1.084890943604200020, 0.8300000000000009592 ) ) ; +#43215 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.3800000000146488977, 0.6999285677985320753 ) ) ; +#43216 = ORIENTED_EDGE ( 'NONE', *, *, #29423, .T. ) ; +#43217 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#43218 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99697, 'distance_accuracy_value', 'NONE'); +#43219 = VECTOR ( 'NONE', #45359, 1000.000000000000000 ) ; +#43220 = VECTOR ( 'NONE', #18051, 1000.000000000000000 ) ; +#43221 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61386, 'distance_accuracy_value', 'NONE'); +#43223 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43222 = FILL_AREA_STYLE ('',( #35599 ) ) ; +#43224 = STYLED_ITEM ( 'NONE', ( #46121 ), #78187 ) ; +#43225 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43226 = LINE ( 'NONE', #63353, #50824 ) ; +#43227 = STYLED_ITEM ( 'NONE', ( #43414 ), #27026 ) ; +#43228 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81575, #50435, #74884, #11497, #75878, #42734 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 4 ), + ( 0.000000000000000000, 0.5000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43229 = EDGE_CURVE ( 'NONE', #30515, #5639, #8569, .T. ) ; +#43230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82390 ), #95386 ) ; +#43231 = ORIENTED_EDGE ( 'NONE', *, *, #35994, .T. ) ; +#43232 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#43233 = SURFACE_SIDE_STYLE ('',( #95824 ) ) ; +#43234 = SURFACE_STYLE_FILL_AREA ( #82066 ) ; +#43235 = SURFACE_STYLE_FILL_AREA ( #50929 ) ; +#43236 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55919, 'distance_accuracy_value', 'NONE'); +#43237 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98829, 'distance_accuracy_value', 'NONE'); +#43238 = FILL_AREA_STYLE_COLOUR ( '', #83342 ) ; +#43239 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43240 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43241 = EDGE_CURVE ( 'NONE', #60864, #65277, #55817, .T. ) ; +#43242 = ORIENTED_EDGE ( 'NONE', *, *, #53499, .T. ) ; +#43243 = ORIENTED_EDGE ( 'NONE', *, *, #14093, .T. ) ; +#43244 = VECTOR ( 'NONE', #79383, 1000.000000000000114 ) ; +#43245 = FACE_OUTER_BOUND ( 'NONE', #12786, .T. ) ; +#43246 = FILL_AREA_STYLE_COLOUR ( '', #44286 ) ; +#43247 = ORIENTED_EDGE ( 'NONE', *, *, #36620, .T. ) ; +#43248 = PRESENTATION_STYLE_ASSIGNMENT (( #66236 ) ) ; +#43249 = EDGE_CURVE ( 'NONE', #49438, #86914, #14771, .T. ) ; +#43250 = CARTESIAN_POINT ( 'NONE', ( -1.305325210527780166, -0.9264544496121620565, 0.8299999999999997380 ) ) ; +#43251 = PRESENTATION_STYLE_ASSIGNMENT (( #3465 ) ) ; +#43253 = ORIENTED_EDGE ( 'NONE', *, *, #54001, .T. ) ; +#43252 = ORIENTED_EDGE ( 'NONE', *, *, #34668, .F. ) ; +#43254 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8992 ), #22115 ) ; +#43255 = VERTEX_POINT ( 'NONE', #496 ) ; +#43256 = VERTEX_POINT ( 'NONE', #9095 ) ; +#43257 = PRESENTATION_STYLE_ASSIGNMENT (( #67726 ) ) ; +#43259 = SURFACE_STYLE_USAGE ( .BOTH. , #35137 ) ; +#43258 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43260 = ORIENTED_EDGE ( 'NONE', *, *, #17438, .T. ) ; +#43261 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#43262 = LINE ( 'NONE', #50959, #91326 ) ; +#43263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36794 ) ) ; +#43264 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, 0.000000000000000000 ) ) ; +#43265 = ORIENTED_EDGE ( 'NONE', *, *, #86531, .T. ) ; +#43266 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43268 = SURFACE_STYLE_FILL_AREA ( #27471 ) ; +#43267 = FACE_OUTER_BOUND ( 'NONE', #51774, .T. ) ; +#43269 = ORIENTED_EDGE ( 'NONE', *, *, #83122, .T. ) ; +#43270 = ORIENTED_EDGE ( 'NONE', *, *, #22591, .T. ) ; +#43271 = EDGE_CURVE ( 'NONE', #86061, #92470, #79137, .T. ) ; +#43272 = PLANE ( 'NONE', #77112 ) ; +#43274 = FILL_AREA_STYLE_COLOUR ( '', #77582 ) ; +#43273 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#43275 = VECTOR ( 'NONE', #51109, 1000.000000000000000 ) ; +#43276 = LINE ( 'NONE', #96366, #60427 ) ; +#43278 = EDGE_LOOP ( 'NONE', ( #13541, #73946, #56384, #62340 ) ) ; +#43277 = LINE ( 'NONE', #65777, #39691 ) ; +#43279 = PLANE ( 'NONE', #56465 ) ; +#43280 = VERTEX_POINT ( 'NONE', #31648 ) ; +#43281 = AXIS2_PLACEMENT_3D ( 'NONE', #84099, #14104, #76428 ) ; +#43282 = VECTOR ( 'NONE', #72120, 1000.000000000000000 ) ; +#43283 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12033 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37913, #76202, #82016 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43284 = ORIENTED_EDGE ( 'NONE', *, *, #84203, .F. ) ; +#43286 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43285 = SURFACE_STYLE_USAGE ( .BOTH. , #66761 ) ; +#43287 = CARTESIAN_POINT ( 'NONE', ( 0.6316964285714280480, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#43288 = EDGE_LOOP ( 'NONE', ( #4835, #36449, #10553, #79826 ) ) ; +#43289 = VERTEX_POINT ( 'NONE', #71467 ) ; +#43291 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, -1.100000000000000089 ) ) ; +#43290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43292 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88923 ) ) ; +#43293 = FILL_AREA_STYLE ('',( #90258 ) ) ; +#43294 = ADVANCED_FACE ( 'NONE', ( #70435 ), #40342, .T. ) ; +#43295 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65593 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66439, #99973, #22480 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43296 = LINE ( 'NONE', #4967, #6726 ) ; +#43297 = STYLED_ITEM ( 'NONE', ( #65017 ), #78329 ) ; +#43298 = AXIS2_PLACEMENT_3D ( 'NONE', #16326, #98657, #5275 ) ; +#43299 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70996 ) ) ; +#43300 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #995, #15780 ), + ( #14754, #69390 ), + ( #92860, #100436 ), + ( #70412, #45902 ), + ( #46419, #84251 ), + ( #77085, #30587 ), + ( #7049, #62289 ), + ( #8051, #39798 ), + ( #70943, #77589 ), + ( #15258, #62800 ), + ( #93861, #99947 ), + ( #32147, #55151 ), + ( #61795, #94327 ), + ( #54638, #38787 ), + ( #68896, #86245 ), + ( #63318, #22982 ), + ( #23479, #21953 ), + ( #477, #7551 ), + ( #78582, #53118 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06711270624433779419, 0.1316627967036529956, 0.1946925457082870070, 0.2551393896941889783, 0.3150988967389439788, 0.3737760910910549739, 0.4326889284963110205, 0.4916570744764819922, 0.5505745229127310125, 0.6091822301749569846, 0.6680950675802129757, 0.7284339546221080264, 0.7906699720419050337, 0.8564705032580119948, 0.9262308729472129576, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43301 = PRESENTATION_STYLE_ASSIGNMENT (( #50992 ) ) ; +#43302 = VERTEX_POINT ( 'NONE', #1531 ) ; +#43303 = ORIENTED_EDGE ( 'NONE', *, *, #77176, .F. ) ; +#43304 = FILL_AREA_STYLE ('',( #90269 ) ) ; +#43305 = CARTESIAN_POINT ( 'NONE', ( -0.01185217942543770157, -1.028719707420159946, 0.8100000000000000533 ) ) ; +#43306 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8100000000000000533 ) ) ; +#43307 = CARTESIAN_POINT ( 'NONE', ( 3.822247875125043937, 8.003630875125045563, 0.8991599999999999593 ) ) ; +#43308 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18808 ) ) ; +#43309 = SURFACE_STYLE_USAGE ( .BOTH. , #4008 ) ; +#43310 = LINE ( 'NONE', #81646, #64743 ) ; +#43312 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43311 = SURFACE_STYLE_USAGE ( .BOTH. , #19835 ) ; +#43313 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43314 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#43315 = SURFACE_STYLE_FILL_AREA ( #37185 ) ; +#43316 = ORIENTED_EDGE ( 'NONE', *, *, #25557, .F. ) ; +#43317 = CIRCLE ( 'NONE', #33581, 0.6999999999379724613 ) ; +#43318 = AXIS2_PLACEMENT_3D ( 'NONE', #22104, #5231, #13361 ) ; +#43319 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#43320 = FILL_AREA_STYLE ('',( #82638 ) ) ; +#43321 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8199999999999999512, 0.000000000000000000 ) ) ; +#43322 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8648700000000000276 ) ) ; +#43323 = SURFACE_STYLE_FILL_AREA ( #41833 ) ; +#43324 = VECTOR ( 'NONE', #7654, 1000.000000000000000 ) ; +#43325 = LINE ( 'NONE', #59201, #16243 ) ; +#43326 = VECTOR ( 'NONE', #21412, 1000.000000000000000 ) ; +#43327 = FILL_AREA_STYLE ('',( #65822 ) ) ; +#43328 = ADVANCED_FACE ( 'NONE', ( #62827 ), #70964, .F. ) ; +#43329 = FILL_AREA_STYLE ('',( #82645 ) ) ; +#43330 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27107 ), #100270 ) ; +#43331 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#43332 = CIRCLE ( 'NONE', #92218, 0.009999999999999998473 ) ; +#43333 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43334 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96066, 'distance_accuracy_value', 'NONE'); +#43335 = ORIENTED_EDGE ( 'NONE', *, *, #34269, .F. ) ; +#43336 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43337 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43338 = EDGE_LOOP ( 'NONE', ( #44764, #85068, #73178, #86931 ) ) ; +#43339 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.02000000000000000042, 0.000000000000000000 ) ) ; +#43340 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#43341 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43342 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43343 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#43344 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999999779, 0.8648700000000000276 ) ) ; +#43345 = VECTOR ( 'NONE', #47824, 1000.000000000000000 ) ; +#43346 = EDGE_LOOP ( 'NONE', ( #34014, #65632, #50548, #99784 ) ) ; +#43347 = ORIENTED_EDGE ( 'NONE', *, *, #74002, .F. ) ; +#43348 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8991599999999999593 ) ) ; +#43349 = FILL_AREA_STYLE ('',( #89815 ) ) ; +#43350 = SURFACE_SIDE_STYLE ('',( #26054 ) ) ; +#43351 = CARTESIAN_POINT ( 'NONE', ( -0.4842236312130879794, -1.167783801559209911, 0.8100000000000000533 ) ) ; +#43352 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74410, 'distance_accuracy_value', 'NONE'); +#43353 = STYLED_ITEM ( 'NONE', ( #78143 ), #90120 ) ; +#43354 = FILL_AREA_STYLE ('',( #12135 ) ) ; +#43355 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22117, 'distance_accuracy_value', 'NONE'); +#43356 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95514 ) ) ; +#43357 = PLANE ( 'NONE', #93433 ) ; +#43358 = PLANE ( 'NONE', #76237 ) ; +#43359 = EDGE_CURVE ( 'NONE', #82715, #48426, #41844, .T. ) ; +#43360 = VECTOR ( 'NONE', #64418, 1000.000000000000000 ) ; +#43361 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01085786437626904723, 0.1500000000000000222 ) ) ; +#43362 = ORIENTED_EDGE ( 'NONE', *, *, #82692, .T. ) ; +#43363 = STYLED_ITEM ( 'NONE', ( #10915 ), #82798 ) ; +#43364 = VECTOR ( 'NONE', #71473, 1000.000000000000000 ) ; +#43365 = FILL_AREA_STYLE_COLOUR ( '', #19374 ) ; +#43366 = ORIENTED_EDGE ( 'NONE', *, *, #67493, .F. ) ; +#43367 = LINE ( 'NONE', #74535, #5453 ) ; +#43368 = VECTOR ( 'NONE', #13665, 1000.000000000000114 ) ; +#43369 = FILL_AREA_STYLE ('',( #12145 ) ) ; +#43370 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#43371 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#43372 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43373 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43374 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63605 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19271, #82096, #67244 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43375 = CARTESIAN_POINT ( 'NONE', ( -1.291038328540720093, -1.030374455384980070, 0.8100000000000000533 ) ) ; +#43376 = LINE ( 'NONE', #75045, #56260 ) ; +#43378 = VERTEX_POINT ( 'NONE', #40844 ) ; +#43377 = ORIENTED_EDGE ( 'NONE', *, *, #4470, .F. ) ; +#43379 = STYLED_ITEM ( 'NONE', ( #85245 ), #61815 ) ; +#43380 = ADVANCED_FACE ( 'NONE', ( #10082 ), #42847, .T. ) ; +#43381 = ORIENTED_EDGE ( 'NONE', *, *, #92528, .T. ) ; +#43383 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.500000000000000000, 0.000000000000000000 ) ) ; +#43382 = LINE ( 'NONE', #12679, #70105 ) ; +#43384 = ORIENTED_EDGE ( 'NONE', *, *, #6511, .F. ) ; +#43385 = EDGE_CURVE ( 'NONE', #33175, #80592, #33173, .T. ) ; +#43386 = VERTEX_POINT ( 'NONE', #65309 ) ; +#43387 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43388 = VECTOR ( 'NONE', #63348, 1000.000000000000114 ) ; +#43389 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43390 = FILL_AREA_STYLE_COLOUR ( '', #18792 ) ; +#43391 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333316872, -2.299999999999999822, 1.747825839084584091E-76 ) ) ; +#43392 = ORIENTED_EDGE ( 'NONE', *, *, #100356, .F. ) ; +#43393 = ORIENTED_EDGE ( 'NONE', *, *, #73224, .T. ) ; +#43394 = VECTOR ( 'NONE', #75013, 1000.000000000000000 ) ; +#43395 = VERTEX_POINT ( 'NONE', #11100 ) ; +#43396 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43397 = EDGE_CURVE ( 'NONE', #60642, #94831, #57699, .T. ) ; +#43398 = EDGE_CURVE ( 'NONE', #64535, #5540, #13291, .T. ) ; +#43399 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999889, -12.64499999999999957 ) ) ; +#43400 = STYLED_ITEM ( 'NONE', ( #70371 ), #13915 ) ; +#43401 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27107 ) ) ; +#43403 = EDGE_CURVE ( 'NONE', #89235, #89436, #80158, .T. ) ; +#43402 = ORIENTED_EDGE ( 'NONE', *, *, #41273, .T. ) ; +#43404 = ADVANCED_FACE ( 'NONE', ( #94913 ), #65828, .T. ) ; +#43405 = LINE ( 'NONE', #74568, #79186 ) ; +#43406 = PRESENTATION_STYLE_ASSIGNMENT (( #42424 ) ) ; +#43407 = ORIENTED_EDGE ( 'NONE', *, *, #37216, .T. ) ; +#43408 = LINE ( 'NONE', #27114, #48525 ) ; +#43409 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#43410 = ORIENTED_EDGE ( 'NONE', *, *, #28768, .T. ) ; +#43411 = VERTEX_POINT ( 'NONE', #29022 ) ; +#43412 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43413 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8648700000000000276 ) ) ; +#43414 = PRESENTATION_STYLE_ASSIGNMENT (( #87867 ) ) ; +#43415 = ADVANCED_FACE ( 'NONE', ( #29520 ), #44315, .T. ) ; +#43416 = SURFACE_STYLE_USAGE ( .BOTH. , #80739 ) ; +#43417 = CARTESIAN_POINT ( 'NONE', ( -1.371024924951979918, -1.079235908285120171, 0.8300000000000000711 ) ) ; +#43418 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43419 = EDGE_CURVE ( 'NONE', #96454, #8122, #59720, .T. ) ; +#43420 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#43421 = FACE_OUTER_BOUND ( 'NONE', #98355, .T. ) ; +#43422 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43423 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43424 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43425 = ORIENTED_EDGE ( 'NONE', *, *, #5879, .T. ) ; +#43426 = CARTESIAN_POINT ( 'NONE', ( -1.084303872719659889, -1.510436674894549913, 0.8299999999999999600 ) ) ; +#43427 = ORIENTED_EDGE ( 'NONE', *, *, #23119, .F. ) ; +#43428 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#43429 = CARTESIAN_POINT ( 'NONE', ( -0.3774402512590340208, -1.154769547699080023, 0.8300000000000000711 ) ) ; +#43430 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3453 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #211, #78341, #64023 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43431 = SURFACE_STYLE_USAGE ( .BOTH. , #50627 ) ; +#43433 = PLANE ( 'NONE', #68726 ) ; +#43432 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2808578643762706384, 0.1499999999999999944 ) ) ; +#43434 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43435 = FACE_OUTER_BOUND ( 'NONE', #38849, .T. ) ; +#43436 = FILL_AREA_STYLE ('',( #90398 ) ) ; +#43437 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17399 ), #36957 ) ; +#43438 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43439 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79307 ), #63002 ) ; +#43440 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.323820061220084998, 0.000000000000000000 ) ) ; +#43441 = EDGE_LOOP ( 'NONE', ( #57154, #71522, #23350, #43410 ) ) ; +#43442 = FILL_AREA_STYLE_COLOUR ( '', #99276 ) ; +#43444 = PRESENTATION_STYLE_ASSIGNMENT (( #82274 ) ) ; +#43443 = PLANE ( 'NONE', #13184 ) ; +#43445 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.1400000000000000133 ) ) ; +#43446 = VECTOR ( 'NONE', #59188, 1000.000000000000000 ) ; +#43447 = EDGE_CURVE ( 'NONE', #92831, #41960, #53020, .T. ) ; +#43448 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77634 ), #71151 ) ; +#43450 = EDGE_CURVE ( 'NONE', #84630, #15490, #76478, .T. ) ; +#43449 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12218, 'distance_accuracy_value', 'NONE'); +#43451 = ORIENTED_EDGE ( 'NONE', *, *, #81681, .F. ) ; +#43452 = SURFACE_SIDE_STYLE ('',( #60809 ) ) ; +#43453 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.900000000000001688, -0.02000000000000000042 ) ) ; +#43455 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17453 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80138, #3522, #40320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43454 = CARTESIAN_POINT ( 'NONE', ( -0.03713474025974040221, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#43456 = DIRECTION ( 'NONE', ( 0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#43457 = AXIS2_PLACEMENT_3D ( 'NONE', #13505, #14538, #5379 ) ; +#43458 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 4.344024262657780003E-34 ) ) ; +#43459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43460 = LINE ( 'NONE', #57827, #63857 ) ; +#43461 = CARTESIAN_POINT ( 'NONE', ( 4.557638875125000766, 6.264148124874999723, 0.8648700000000000276 ) ) ; +#43462 = SURFACE_STYLE_FILL_AREA ( #83285 ) ; +#43463 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43464 = AXIS2_PLACEMENT_3D ( 'NONE', #31840, #56386, #95611 ) ; +#43465 = DIRECTION ( 'NONE', ( 0.7071067811865479058, 0.7071067811865470176, 0.000000000000000000 ) ) ; +#43466 = ORIENTED_EDGE ( 'NONE', *, *, #7122, .T. ) ; +#43467 = EDGE_LOOP ( 'NONE', ( #98385, #65435, #35569, #36864 ) ) ; +#43468 = VECTOR ( 'NONE', #23321, 1000.000000000000000 ) ; +#43469 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85716, 'distance_accuracy_value', 'NONE'); +#43470 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#43471 = FACE_OUTER_BOUND ( 'NONE', #59768, .T. ) ; +#43472 = FILL_AREA_STYLE_COLOUR ( '', #49393 ) ; +#43473 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43474 = SURFACE_STYLE_USAGE ( .BOTH. , #12253 ) ; +#43475 = PRESENTATION_STYLE_ASSIGNMENT (( #66461 ) ) ; +#43476 = DIRECTION ( 'NONE', ( -0.7071064476869688420, 0.7071071146859688739, 0.000000000000000000 ) ) ; +#43477 = CARTESIAN_POINT ( 'NONE', ( -1.632862398863140093E-18, 0.8199999999999998401, 0.04999999999999998890 ) ) ; +#43478 = ORIENTED_EDGE ( 'NONE', *, *, #15929, .T. ) ; +#43479 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#43481 = EDGE_CURVE ( 'NONE', #35264, #46763, #75486, .T. ) ; +#43480 = SURFACE_STYLE_USAGE ( .BOTH. , #12259 ) ; +#43482 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81649, #67777, #73968, #13601 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43483 = ORIENTED_EDGE ( 'NONE', *, *, #85462, .F. ) ; +#43484 = SURFACE_STYLE_FILL_AREA ( #3677 ) ; +#43485 = EDGE_LOOP ( 'NONE', ( #25528, #7127, #83931, #27340 ) ) ; +#43486 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48477 ) ) ; +#43487 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43488 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#43489 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43490 = FILL_AREA_STYLE ('',( #66473 ) ) ; +#43491 = ORIENTED_EDGE ( 'NONE', *, *, #80253, .T. ) ; +#43492 = SURFACE_SIDE_STYLE ('',( #66479 ) ) ; +#43493 = PRESENTATION_STYLE_ASSIGNMENT (( #97588 ) ) ; +#43494 = ORIENTED_EDGE ( 'NONE', *, *, #30535, .T. ) ; +#43495 = FILL_AREA_STYLE_COLOUR ( '', #44311 ) ; +#43496 = VERTEX_POINT ( 'NONE', #89796 ) ; +#43497 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43498 = ORIENTED_EDGE ( 'NONE', *, *, #11587, .F. ) ; +#43499 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51432 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69761, #86612, #31483 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43500 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#43501 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43502 = VECTOR ( 'NONE', #87007, 1000.000000000000000 ) ; +#43503 = SURFACE_STYLE_FILL_AREA ( #68485 ) ; +#43504 = ORIENTED_EDGE ( 'NONE', *, *, #14076, .T. ) ; +#43505 = ORIENTED_EDGE ( 'NONE', *, *, #91675, .F. ) ; +#43506 = PLANE ( 'NONE', #98737 ) ; +#43507 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #74487, #90282, #67293, #96918 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43508 = ORIENTED_EDGE ( 'NONE', *, *, #42, .F. ) ; +#43509 = SURFACE_SIDE_STYLE ('',( #96108 ) ) ; +#43510 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55145 ), #15715 ) ; +#43512 = VERTEX_POINT ( 'NONE', #97909 ) ; +#43511 = SURFACE_SIDE_STYLE ('',( #82834 ) ) ; +#43513 = EDGE_CURVE ( 'NONE', #76538, #26712, #51029, .T. ) ; +#43514 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30505 ) ) ; +#43515 = PRESENTATION_STYLE_ASSIGNMENT (( #52220 ) ) ; +#43516 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43518 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62538 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57723, #34731, #96958 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43517 = SURFACE_SIDE_STYLE ('',( #89505 ) ) ; +#43519 = ORIENTED_EDGE ( 'NONE', *, *, #30323, .T. ) ; +#43520 = SURFACE_SIDE_STYLE ('',( #98080 ) ) ; +#43521 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 1.668003342285390072E-16 ) ) ; +#43522 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, -0.9464466094067263136 ) ) ; +#43523 = ORIENTED_EDGE ( 'NONE', *, *, #19801, .F. ) ; +#43524 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43525 = LINE ( 'NONE', #42544, #13761 ) ; +#43526 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87564 ) ) ; +#43527 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#43528 = EDGE_CURVE ( 'NONE', #89867, #95525, #20352, .T. ) ; +#43529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87570 ) ) ; +#43530 = SURFACE_SIDE_STYLE ('',( #98093 ) ) ; +#43532 = LINE ( 'NONE', #12826, #64689 ) ; +#43531 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.500000000000000222, 0.8100000000000000533 ) ) ; +#43533 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43534 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 7.671291000000000082, 0.8991599999999999593 ) ) ; +#43535 = VERTEX_POINT ( 'NONE', #66813 ) ; +#43536 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43537 = FACE_OUTER_BOUND ( 'NONE', #22114, .T. ) ; +#43538 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#43540 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43539 = CARTESIAN_POINT ( 'NONE', ( 0.3880979930239000231, -0.9663965808142249703, 0.8100000000000000533 ) ) ; +#43541 = SURFACE_STYLE_FILL_AREA ( #12329 ) ; +#43542 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#43543 = FILL_AREA_STYLE_COLOUR ( '', #7419 ) ; +#43544 = FILL_AREA_STYLE ('',( #35435 ) ) ; +#43545 = PLANE ( 'NONE', #44206 ) ; +#43546 = ORIENTED_EDGE ( 'NONE', *, *, #8376, .F. ) ; +#43547 = FACE_OUTER_BOUND ( 'NONE', #99289, .T. ) ; +#43548 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#43549 = VERTEX_POINT ( 'NONE', #28042 ) ; +#43550 = EDGE_CURVE ( 'NONE', #71809, #20861, #91512, .T. ) ; +#43551 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43552 = VECTOR ( 'NONE', #31507, 1000.000000000000000 ) ; +#43553 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43554 = FILL_AREA_STYLE ('',( #59931 ) ) ; +#43555 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43556 = STYLED_ITEM ( 'NONE', ( #73733 ), #83996 ) ; +#43557 = PLANE ( 'NONE', #1369 ) ; +#43558 = FACE_OUTER_BOUND ( 'NONE', #63489, .T. ) ; +#43559 = EDGE_CURVE ( 'NONE', #59283, #4914, #39697, .T. ) ; +#43560 = ORIENTED_EDGE ( 'NONE', *, *, #77908, .F. ) ; +#43561 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.899999999999999911, 0.8299999999999999600 ) ) ; +#43562 = LINE ( 'NONE', #81417, #88134 ) ; +#43563 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#43564 = LINE ( 'NONE', #89552, #21589 ) ; +#43565 = CARTESIAN_POINT ( 'NONE', ( 1.134147553444200041, -1.508462442331270026, 0.8300000000000010703 ) ) ; +#43566 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#43567 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#43568 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91076 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41441, #62405, #55751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43569 = FILL_AREA_STYLE ('',( #74235 ) ) ; +#43570 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333326642, 1.100000000000000089, 0.000000000000000000 ) ) ; +#43571 = AXIS2_PLACEMENT_3D ( 'NONE', #39614, #100264, #30938 ) ; +#43572 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999631406, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#43573 = VECTOR ( 'NONE', #94153, 1000.000000000000000 ) ; +#43574 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43575 = VECTOR ( 'NONE', #54654, 1000.000000000000000 ) ; +#43576 = ORIENTED_EDGE ( 'NONE', *, *, #69400, .T. ) ; +#43577 = SURFACE_SIDE_STYLE ('',( #82910 ) ) ; +#43578 = ORIENTED_EDGE ( 'NONE', *, *, #78235, .F. ) ; +#43579 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43581 = AXIS2_PLACEMENT_3D ( 'NONE', #66197, #97302, #58575 ) ; +#43580 = PRESENTATION_STYLE_ASSIGNMENT (( #38694 ) ) ; +#43582 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, -0.1000000000000000056, -0.02000000000002929990 ) ) ; +#43583 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43584 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#43585 = VECTOR ( 'NONE', #19882, 1000.000000000000000 ) ; +#43586 = LINE ( 'NONE', #3795, #90770 ) ; +#43587 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #90943, #75134, #29168, #5627 ), + ( #61338, #67928, #60335, #91440 ), + ( #30133, #44941, #68925, #68438 ), + ( #37826, #45935, #76613, #6604 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#43588 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43589 = CLOSED_SHELL ( 'NONE', ( #7632, #34398, #99623, #57867, #34475, #84956 ) ) ; +#43590 = ORIENTED_EDGE ( 'NONE', *, *, #80043, .F. ) ; +#43591 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#43592 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38716 ), #55003 ) ; +#43593 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71304 ) ) ; +#43594 = SURFACE_STYLE_FILL_AREA ( #4790 ) ; +#43595 = ORIENTED_EDGE ( 'NONE', *, *, #45277, .F. ) ; +#43596 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43597 = EDGE_CURVE ( 'NONE', #60744, #87112, #55042, .T. ) ; +#43598 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82298 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1984, #15229, #64264 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43599 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999997558, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#43600 = FACE_OUTER_BOUND ( 'NONE', #9147, .T. ) ; +#43601 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43602 = ORIENTED_EDGE ( 'NONE', *, *, #10072, .T. ) ; +#43603 = PRESENTATION_STYLE_ASSIGNMENT (( #65095 ) ) ; +#43605 = STYLED_ITEM ( 'NONE', ( #55558 ), #43610 ) ; +#43604 = CARTESIAN_POINT ( 'NONE', ( 0.2314326298701299134, 0.6899999999999999467, -2.168404344971008868E-16 ) ) ; +#43606 = LINE ( 'NONE', #67584, #60882 ) ; +#43607 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43608 = EDGE_CURVE ( 'NONE', #839, #43148, #16180, .T. ) ; +#43609 = ORIENTED_EDGE ( 'NONE', *, *, #66548, .T. ) ; +#43610 = ADVANCED_FACE ( 'NONE', ( #24409 ), #54540, .T. ) ; +#43611 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#43612 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#43613 = CARTESIAN_POINT ( 'NONE', ( -1.162861419240297289, -1.222953069365746881, 0.8099999999998237499 ) ) ; +#43614 = ORIENTED_EDGE ( 'NONE', *, *, #7646, .F. ) ; +#43615 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4849999999999999867, 0.2400000000000000189 ) ) ; +#43616 = AXIS2_PLACEMENT_3D ( 'NONE', #21838, #28994, #13600 ) ; +#43617 = EDGE_LOOP ( 'NONE', ( #39417, #76777, #79077, #59376 ) ) ; +#43619 = ORIENTED_EDGE ( 'NONE', *, *, #59311, .F. ) ; +#43618 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43620 = EDGE_CURVE ( 'NONE', #21864, #82566, #22064, .T. ) ; +#43621 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12597 ) ) ; +#43622 = VECTOR ( 'NONE', #96674, 1000.000000000000000 ) ; +#43623 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38896, 'distance_accuracy_value', 'NONE'); +#43624 = FILL_AREA_STYLE ('',( #12420 ) ) ; +#43625 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#43626 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#43627 = CARTESIAN_POINT ( 'NONE', ( 8.800279041625021392, 6.264147958374939762, 0.8991599999999999593 ) ) ; +#43628 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999667, -1.504632769052528352E-33 ) ) ; +#43629 = FILL_AREA_STYLE ('',( #61001 ) ) ; +#43630 = ORIENTED_EDGE ( 'NONE', *, *, #72913, .F. ) ; +#43631 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72382 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48255, #40591, #34454 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43632 = SURFACE_STYLE_FILL_AREA ( #11917 ) ; +#43633 = LINE ( 'NONE', #73799, #96893 ) ; +#43634 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#43635 = ORIENTED_EDGE ( 'NONE', *, *, #13271, .F. ) ; +#43636 = STYLED_ITEM ( 'NONE', ( #20684 ), #79373 ) ; +#43638 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 1.458578643762689975, -0.02000000000000000042 ) ) ; +#43637 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.000000000000000000 ) ) ; +#43639 = ORIENTED_EDGE ( 'NONE', *, *, #52803, .T. ) ; +#43640 = AXIS2_PLACEMENT_3D ( 'NONE', #36142, #42778, #13053 ) ; +#43642 = FACE_OUTER_BOUND ( 'NONE', #8116, .T. ) ; +#43641 = CARTESIAN_POINT ( 'NONE', ( 0.2682095001753613261, -1.284753514366673066, 0.8100000000000002753 ) ) ; +#43643 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#43644 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88643 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29269, #59455, #37447 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43645 = CIRCLE ( 'NONE', #51847, 0.009999999999999998473 ) ; +#43646 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#43647 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43648 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28940 ), #2872 ) ; +#43649 = VECTOR ( 'NONE', #21894, 1000.000000000000114 ) ; +#43650 = SURFACE_SIDE_STYLE ('',( #51850 ) ) ; +#43651 = VERTEX_POINT ( 'NONE', #85653 ) ; +#43652 = CARTESIAN_POINT ( 'NONE', ( -4.898587196589412459E-17, 0.7578679656440356904, 0.2000000000000000111 ) ) ; +#43653 = ORIENTED_EDGE ( 'NONE', *, *, #25577, .T. ) ; +#43654 = CLOSED_SHELL ( 'NONE', ( #87330, #55207, #61496, #80574, #73962, #39232 ) ) ; +#43655 = LINE ( 'NONE', #97746, #68858 ) ; +#43656 = VECTOR ( 'NONE', #99964, 1000.000000000000114 ) ; +#43657 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, 0.000000000000000000 ) ) ; +#43658 = EDGE_CURVE ( 'NONE', #7394, #66856, #45805, .T. ) ; +#43659 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43660 = SURFACE_SIDE_STYLE ('',( #36047 ) ) ; +#43661 = LINE ( 'NONE', #20184, #99104 ) ; +#43662 = CARTESIAN_POINT ( 'NONE', ( 1.263543985521710100, -0.9656714926165439472, 0.8100000000000000533 ) ) ; +#43663 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19181 ), #14256 ) ; +#43664 = VERTEX_POINT ( 'NONE', #6951 ) ; +#43665 = EDGE_CURVE ( 'NONE', #92420, #22042, #77480, .T. ) ; +#43666 = LINE ( 'NONE', #99223, #95408 ) ; +#43667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43668 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59980 ), #20870 ) ; +#43669 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#43672 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43671 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 0.1000000000000000056, -12.01999999999999957 ) ) ; +#43670 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43673 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20635, 'distance_accuracy_value', 'NONE'); +#43674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43675 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#43676 = CARTESIAN_POINT ( 'NONE', ( 4.798055249750023954, 8.979437750249974926, 0.8991599999999999593 ) ) ; +#43677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43678 = EDGE_CURVE ( 'NONE', #53559, #34143, #22353, .T. ) ; +#43679 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43680 = VERTEX_POINT ( 'NONE', #47870 ) ; +#43681 = FILL_AREA_STYLE_COLOUR ( '', #66834 ) ; +#43682 = PRESENTATION_STYLE_ASSIGNMENT (( #51385 ) ) ; +#43683 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43685 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999940048, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#43686 = VECTOR ( 'NONE', #66065, 1000.000000000000000 ) ; +#43687 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#43688 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74877 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9330, #17052, #62556 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43689 = SURFACE_STYLE_USAGE ( .BOTH. , #22227 ) ; +#43690 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.300000000000000044, -0.02000000000002094894 ) ) ; +#43691 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71568, #1623, #65388, #64405, #34297, #73072, #33778, #49602, #11185, #80748, #80242, #95508, #81263, #32760, #10682, #50122, #3120, #95003, #63907 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.262573730638264933E-05, 4.402765250703571861E-05, 6.465154594402047522E-05, 8.441173817581946320E-05, 0.0001035680121129804813, 0.0001220861719339233801, 0.0001402559123783361219, 0.0001583361553105063413, 0.0001764659445596329819, 0.0001948125555069058195, 0.0002134630513528897673, 0.0002327856209059041672, 0.0002527554153283439976, 0.0002733299553459914415, 0.0002947318705466448157, 0.0003171241394516479371 ), + .UNSPECIFIED. ) ; +#43692 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43693 = FILL_AREA_STYLE_COLOUR ( '', #45069 ) ; +#43694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43695 = SURFACE_STYLE_FILL_AREA ( #3900 ) ; +#43696 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52147 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6327, #91643, #43677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43697 = LINE ( 'NONE', #20728, #87620 ) ; +#43698 = SURFACE_SIDE_STYLE ('',( #69152 ) ) ; +#43699 = PRESENTATION_STYLE_ASSIGNMENT (( #35083 ) ) ; +#43700 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261924000000000046, 0.8991599999999999593 ) ) ; +#43701 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32353 ) ) ; +#43702 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#43703 = SURFACE_SIDE_STYLE ('',( #88189 ) ) ; +#43704 = VECTOR ( 'NONE', #3800, 1000.000000000000000 ) ; +#43705 = CARTESIAN_POINT ( 'NONE', ( 1.766025874245259919, -1.139163918933580266, 0.8299999999999997380 ) ) ; +#43706 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#43707 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43708 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041100000000085, 0.8991599999999999593 ) ) ; +#43709 = EDGE_LOOP ( 'NONE', ( #52577, #92692, #91972, #9567 ) ) ; +#43711 = AXIS2_PLACEMENT_3D ( 'NONE', #19349, #64816, #27042 ) ; +#43710 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43712 = SURFACE_SIDE_STYLE ('',( #89692 ) ) ; +#43713 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43716 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43715 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#43714 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43717 = CARTESIAN_POINT ( 'NONE', ( -0.03785612751057330916, -0.9872600217210630857, 0.8300000000000002931 ) ) ; +#43718 = ADVANCED_FACE ( 'NONE', ( #61198 ), #15680, .T. ) ; +#43719 = FILL_AREA_STYLE_COLOUR ( '', #26612 ) ; +#43720 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#43721 = ORIENTED_EDGE ( 'NONE', *, *, #11993, .T. ) ; +#43722 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89594 ), #57049 ) ; +#43723 = ORIENTED_EDGE ( 'NONE', *, *, #80766, .F. ) ; +#43724 = SURFACE_SIDE_STYLE ('',( #43234 ) ) ; +#43725 = LINE ( 'NONE', #83558, #27705 ) ; +#43726 = VECTOR ( 'NONE', #71608, 1000.000000000000000 ) ; +#43727 = LINE ( 'NONE', #69585, #91820 ) ; +#43728 = SURFACE_STYLE_USAGE ( .BOTH. , #20762 ) ; +#43729 = AXIS2_PLACEMENT_3D ( 'NONE', #98787, #60115, #21257 ) ; +#43730 = CLOSED_SHELL ( 'NONE', ( #83096, #87296, #12837, #62228, #85575, #47201 ) ) ; +#43731 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#43732 = ADVANCED_FACE ( 'NONE', ( #81436 ), #43089, .T. ) ; +#43733 = ORIENTED_EDGE ( 'NONE', *, *, #57004, .T. ) ; +#43734 = ORIENTED_EDGE ( 'NONE', *, *, #89997, .F. ) ; +#43735 = ADVANCED_FACE ( 'NONE', ( #34958 ), #34464, .T. ) ; +#43736 = VERTEX_POINT ( 'NONE', #58961 ) ; +#43737 = CARTESIAN_POINT ( 'NONE', ( 1.809085324296979991, -1.273483528256009967, 0.8100000000000000533 ) ) ; +#43738 = STYLED_ITEM ( 'NONE', ( #474 ), #50559 ) ; +#43739 = EDGE_CURVE ( 'NONE', #18416, #74391, #19095, .T. ) ; +#43740 = FILL_AREA_STYLE_COLOUR ( '', #40253 ) ; +#43741 = FILL_AREA_STYLE ('',( #12020 ) ) ; +#43742 = CARTESIAN_POINT ( 'NONE', ( -1.175853632737690058, -0.8847374564574109757, 0.8299999999999997380 ) ) ; +#43743 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43744 = CIRCLE ( 'NONE', #73070, 0.2500000000000000000 ) ; +#43746 = ORIENTED_EDGE ( 'NONE', *, *, #22714, .T. ) ; +#43745 = VERTEX_POINT ( 'NONE', #28288 ) ; +#43747 = ORIENTED_EDGE ( 'NONE', *, *, #35916, .F. ) ; +#43748 = VECTOR ( 'NONE', #11233, 1000.000000000000000 ) ; +#43749 = ORIENTED_EDGE ( 'NONE', *, *, #28445, .T. ) ; +#43750 = LINE ( 'NONE', #36629, #42667 ) ; +#43751 = PLANE ( 'NONE', #31305 ) ; +#43752 = EDGE_CURVE ( 'NONE', #94847, #86420, #59468, .T. ) ; +#43753 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27395, 'distance_accuracy_value', 'NONE'); +#43754 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.100000000000000089 ) ) ; +#43756 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43755 = CARTESIAN_POINT ( 'NONE', ( 0.4328235538323689791, -0.9111919069839470309, 0.8299999999999999600 ) ) ; +#43757 = LINE ( 'NONE', #4937, #80869 ) ; +#43758 = EDGE_CURVE ( 'NONE', #30033, #72400, #88553, .T. ) ; +#43759 = FILL_AREA_STYLE ('',( #59140 ) ) ; +#43760 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33049 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35748, #74542, #13669 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43761 = CARTESIAN_POINT ( 'NONE', ( -1.272737459667760085, -0.9076590548536880299, 0.8299999999999999600 ) ) ; +#43762 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94918 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82651, #43835, #60685 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43763 = EDGE_LOOP ( 'NONE', ( #30397, #85228, #3929, #54603 ) ) ; +#43765 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43764 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43766 = ORIENTED_EDGE ( 'NONE', *, *, #84339, .F. ) ; +#43767 = VERTEX_POINT ( 'NONE', #45544 ) ; +#43768 = CARTESIAN_POINT ( 'NONE', ( 1.172627409212990024, -1.219266740403220028, 0.8299999999999999600 ) ) ; +#43769 = EDGE_CURVE ( 'NONE', #41410, #81594, #29763, .T. ) ; +#43770 = FILL_AREA_STYLE_COLOUR ( '', #74390 ) ; +#43771 = SURFACE_SIDE_STYLE ('',( #12567 ) ) ; +#43772 = ADVANCED_FACE ( 'NONE', ( #77231 ), #7211, .T. ) ; +#43773 = SURFACE_STYLE_USAGE ( .BOTH. , #67255 ) ; +#43775 = VERTEX_POINT ( 'NONE', #60457 ) ; +#43774 = FACE_OUTER_BOUND ( 'NONE', #77905, .T. ) ; +#43776 = VECTOR ( 'NONE', #96483, 1000.000000000000114 ) ; +#43777 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43778 = ORIENTED_EDGE ( 'NONE', *, *, #77955, .F. ) ; +#43779 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88198 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54139, #54665, #67679 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43780 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#43781 = SURFACE_STYLE_FILL_AREA ( #88258 ) ; +#43782 = ORIENTED_EDGE ( 'NONE', *, *, #75436, .F. ) ; +#43784 = PRESENTATION_STYLE_ASSIGNMENT (( #13571 ) ) ; +#43783 = LINE ( 'NONE', #36156, #54762 ) ; +#43785 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#43786 = ORIENTED_EDGE ( 'NONE', *, *, #64943, .F. ) ; +#43787 = ORIENTED_EDGE ( 'NONE', *, *, #29553, .T. ) ; +#43790 = SURFACE_SIDE_STYLE ('',( #12581 ) ) ; +#43789 = CARTESIAN_POINT ( 'NONE', ( 0.4491032436848350073, -0.9174134460922771517, 0.8299999999999992939 ) ) ; +#43788 = PRODUCT_DEFINITION ( 'δ֪', '', #63347, #69812 ) ; +#43791 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43792 = SURFACE_STYLE_USAGE ( .BOTH. , #66765 ) ; +#43793 = FILL_AREA_STYLE ('',( #98833 ) ) ; +#43794 = VECTOR ( 'NONE', #1110, 1000.000000000000000 ) ; +#43795 = SURFACE_STYLE_USAGE ( .BOTH. , #98348 ) ; +#43796 = LINE ( 'NONE', #51990, #82131 ) ; +#43797 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43799 = STYLED_ITEM ( 'NONE', ( #34283 ), #17475 ) ; +#43798 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6964, 'distance_accuracy_value', 'NONE'); +#43800 = ORIENTED_EDGE ( 'NONE', *, *, #36387, .T. ) ; +#43801 = ADVANCED_FACE ( 'NONE', ( #61950 ), #98631, .F. ) ; +#43802 = STYLED_ITEM ( 'NONE', ( #36446 ), #63311 ) ; +#43803 = SURFACE_SIDE_STYLE ('',( #82627 ) ) ; +#43804 = EDGE_LOOP ( 'NONE', ( #58725, #58739, #57487, #26413 ) ) ; +#43805 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35681 ) ) ; +#43806 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#43807 = CARTESIAN_POINT ( 'NONE', ( -0.05398490405131480679, -0.9763607356531520676, 0.8100000000000000533 ) ) ; +#43808 = FACE_OUTER_BOUND ( 'NONE', #31621, .T. ) ; +#43809 = VECTOR ( 'NONE', #93163, 1000.000000000000000 ) ; +#43810 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#43811 = FILL_AREA_STYLE_COLOUR ( '', #45385 ) ; +#43812 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43813 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19323 ) ) ; +#43814 = PLANE ( 'NONE', #90749 ) ; +#43815 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43816 = EDGE_CURVE ( 'NONE', #59846, #79825, #53271, .T. ) ; +#43817 = ORIENTED_EDGE ( 'NONE', *, *, #78330, .F. ) ; +#43818 = DIRECTION ( 'NONE', ( 0.7071045084557385785, 0.7071090539100516326, 0.000000000000000000 ) ) ; +#43819 = SURFACE_STYLE_USAGE ( .BOTH. , #100562 ) ; +#43820 = SURFACE_STYLE_FILL_AREA ( #20332 ) ; +#43821 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43822 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43823 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#43824 = AXIS2_PLACEMENT_3D ( 'NONE', #25014, #16269, #993 ) ; +#43825 = EDGE_CURVE ( 'NONE', #64838, #48055, #86095, .T. ) ; +#43826 = CARTESIAN_POINT ( 'NONE', ( 1.901254715655620098, -1.325441991778449902, 0.8100000000000000533 ) ) ; +#43827 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22617 ) ) ; +#43828 = EDGE_CURVE ( 'NONE', #100318, #29842, #69407, .T. ) ; +#43829 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000005496, 0.2458578643762690530 ) ) ; +#43830 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#43831 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#43832 = PRESENTATION_STYLE_ASSIGNMENT (( #96422 ) ) ; +#43833 = ORIENTED_EDGE ( 'NONE', *, *, #30362, .T. ) ; +#43834 = CARTESIAN_POINT ( 'NONE', ( 0.01300123242974935561, -1.477174517193589942, 0.8099999999995332045 ) ) ; +#43835 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43836 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43837 = ORIENTED_EDGE ( 'NONE', *, *, #11329, .F. ) ; +#43838 = CARTESIAN_POINT ( 'NONE', ( -0.5300000000829642177, 0.2500000001077752332, -1.665334536835250932E-17 ) ) ; +#43839 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220025313, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#43840 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43841 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66832 ) ) ; +#43842 = VECTOR ( 'NONE', #77875, 1000.000000000000000 ) ; +#43843 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61129, #22810, #69208 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43844 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#43845 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43846 = ADVANCED_FACE ( 'NONE', ( #36945 ), #75253, .T. ) ; +#43847 = ADVANCED_FACE ( 'NONE', ( #8715 ), #85402, .T. ) ; +#43848 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66652 ), #50388 ) ; +#43849 = AXIS2_PLACEMENT_3D ( 'NONE', #35703, #88794, #41839 ) ; +#43850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43851 = ORIENTED_EDGE ( 'NONE', *, *, #22, .T. ) ; +#43852 = ORIENTED_EDGE ( 'NONE', *, *, #67334, .F. ) ; +#43853 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27638 ), #38978 ) ; +#43854 = SURFACE_SIDE_STYLE ('',( #28537 ) ) ; +#43855 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87884 ) ) ; +#43856 = VECTOR ( 'NONE', #67559, 1000.000000000000000 ) ; +#43857 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43858 = PLANE ( 'NONE', #81177 ) ; +#43859 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43861 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43860 = AXIS2_PLACEMENT_3D ( 'NONE', #85026, #15037, #77878 ) ; +#43862 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#43863 = VERTEX_POINT ( 'NONE', #129 ) ; +#43864 = EDGE_LOOP ( 'NONE', ( #30966, #9277, #33878, #99564, #83949, #1998, #17877, #37680, #95602, #16070, #89234, #39673 ) ) ; +#43865 = EDGE_CURVE ( 'NONE', #65755, #58838, #1141, .T. ) ; +#43866 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63486 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88282, #33150, #24519 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43867 = ORIENTED_EDGE ( 'NONE', *, *, #14906, .F. ) ; +#43868 = EDGE_CURVE ( 'NONE', #98340, #97223, #42107, .T. ) ; +#43869 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#43870 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#43871 = STYLED_ITEM ( 'NONE', ( #58158 ), #17787 ) ; +#43872 = CARTESIAN_POINT ( 'NONE', ( -0.3688392660424539837, -1.039320398944010071, 0.8299999999999999600 ) ) ; +#43873 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88457, #18496, #49681, #31816 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43874 = CARTESIAN_POINT ( 'NONE', ( -1.231483759408549927, -0.9661431204389000493, 0.8100000000000000533 ) ) ; +#43875 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43876 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66682 ), #86289 ) ; +#43878 = ORIENTED_EDGE ( 'NONE', *, *, #33690, .F. ) ; +#43877 = ORIENTED_EDGE ( 'NONE', *, *, #24499, .T. ) ; +#43879 = STYLED_ITEM ( 'NONE', ( #86558 ), #42202 ) ; +#43880 = ORIENTED_EDGE ( 'NONE', *, *, #74302, .F. ) ; +#43881 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7673, 'distance_accuracy_value', 'NONE'); +#43882 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6859, 'distance_accuracy_value', 'NONE'); +#43883 = SURFACE_SIDE_STYLE ('',( #51590 ) ) ; +#43884 = STYLED_ITEM ( 'NONE', ( #11180 ), #390 ) ; +#43885 = ORIENTED_EDGE ( 'NONE', *, *, #15706, .T. ) ; +#43886 = ORIENTED_EDGE ( 'NONE', *, *, #71095, .T. ) ; +#43887 = PRESENTATION_STYLE_ASSIGNMENT (( #67368 ) ) ; +#43888 = ADVANCED_FACE ( 'NONE', ( #95052 ), #87422, .F. ) ; +#43889 = CARTESIAN_POINT ( 'NONE', ( 9.846469000000002580, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#43890 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#43891 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43892 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43894 = EDGE_LOOP ( 'NONE', ( #19809, #2725, #52028, #88112 ) ) ; +#43893 = VECTOR ( 'NONE', #47837, 1000.000000000000000 ) ; +#43895 = ORIENTED_EDGE ( 'NONE', *, *, #54299, .T. ) ; +#43896 = FILL_AREA_STYLE ('',( #50589 ) ) ; +#43897 = ORIENTED_EDGE ( 'NONE', *, *, #44372, .F. ) ; +#43898 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43899 = VECTOR ( 'NONE', #32431, 1000.000000000000000 ) ; +#43900 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#43901 = EDGE_CURVE ( 'NONE', #100280, #82294, #6160, .T. ) ; +#43902 = EDGE_CURVE ( 'NONE', #79706, #51323, #33317, .T. ) ; +#43905 = ORIENTED_EDGE ( 'NONE', *, *, #84263, .T. ) ; +#43904 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26545 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23919, #70338, #86684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43903 = CARTESIAN_POINT ( 'NONE', ( 0.7761769480519481457, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#43906 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#43907 = ORIENTED_EDGE ( 'NONE', *, *, #30278, .T. ) ; +#43908 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43909 = LINE ( 'NONE', #98452, #3645 ) ; +#43910 = EDGE_LOOP ( 'NONE', ( #31076, #36374, #20080, #34281 ) ) ; +#43911 = ORIENTED_EDGE ( 'NONE', *, *, #17588, .T. ) ; +#43912 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96847, #37497, #68598, #26446 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43913 = LINE ( 'NONE', #35295, #70974 ) ; +#43914 = LINE ( 'NONE', #97973, #85508 ) ; +#43915 = VECTOR ( 'NONE', #20103, 1000.000000000000000 ) ; +#43916 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43917 = LINE ( 'NONE', #51111, #30825 ) ; +#43918 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#43919 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45923 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9479, #35584, #95797 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43920 = LINE ( 'NONE', #75091, #26316 ) ; +#43921 = EDGE_LOOP ( 'NONE', ( #25613, #53698, #85962, #52210 ) ) ; +#43922 = FACE_OUTER_BOUND ( 'NONE', #53897, .T. ) ; +#43923 = EDGE_CURVE ( 'NONE', #49182, #83076, #54279, .T. ) ; +#43924 = CARTESIAN_POINT ( 'NONE', ( -1.105094510553189968, -1.513291690750319995, 0.8299999999999999600 ) ) ; +#43925 = ORIENTED_EDGE ( 'NONE', *, *, #50698, .F. ) ; +#43926 = SURFACE_STYLE_FILL_AREA ( #21947 ) ; +#43927 = AXIS2_PLACEMENT_3D ( 'NONE', #93915, #20757, #74393 ) ; +#43928 = AXIS2_PLACEMENT_3D ( 'NONE', #80291, #10223, #94031 ) ; +#43929 = PRESENTATION_STYLE_ASSIGNMENT (( #6065 ) ) ; +#43931 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#43930 = VECTOR ( 'NONE', #85520, 1000.000000000000114 ) ; +#43932 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 4.524664999999999715, 0.8648700000000000276 ) ) ; +#43933 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92695 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78304, #26207, #55831 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43935 = EDGE_CURVE ( 'NONE', #49302, #20227, #11728, .T. ) ; +#43934 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#43936 = PLANE ( 'NONE', #91848 ) ; +#43937 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70013 ), #19460 ) ; +#43938 = SURFACE_STYLE_FILL_AREA ( #83263 ) ; +#43939 = CIRCLE ( 'NONE', #74926, 0.1000000000000000194 ) ; +#43940 = SURFACE_STYLE_USAGE ( .BOTH. , #51643 ) ; +#43941 = EDGE_CURVE ( 'NONE', #82972, #449, #27177, .T. ) ; +#43942 = FILL_AREA_STYLE_COLOUR ( '', #5840 ) ; +#43943 = SURFACE_STYLE_USAGE ( .BOTH. , #36306 ) ; +#43944 = AXIS2_PLACEMENT_3D ( 'NONE', #35181, #40816, #65803 ) ; +#43946 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, -4.299223014629187820E-17, -0.8499999999999999778 ) ) ; +#43945 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#43947 = PRESENTATION_STYLE_ASSIGNMENT (( #98491 ) ) ; +#43948 = AXIS2_PLACEMENT_3D ( 'NONE', #69914, #83381, #90527 ) ; +#43949 = ADVANCED_FACE ( 'NONE', ( #58335 ), #64951, .T. ) ; +#43950 = PLANE ( 'NONE', #30502 ) ; +#43951 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69433 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54296, #6723, #39457 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43952 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98564 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44891, #94877, #18281 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#43953 = EDGE_CURVE ( 'NONE', #61356, #25443, #52462, .T. ) ; +#43954 = ORIENTED_EDGE ( 'NONE', *, *, #22738, .F. ) ; +#43955 = CARTESIAN_POINT ( 'NONE', ( -0.9900422999955440506, -1.351484773706350007, 0.8100000000000000533 ) ) ; +#43956 = CARTESIAN_POINT ( 'NONE', ( 0.6166666666666670293, -3.099999999999980549, 0.000000000000000000 ) ) ; +#43957 = FILL_AREA_STYLE ('',( #68429 ) ) ; +#43958 = PLANE ( 'NONE', #12741 ) ; +#43959 = SURFACE_SIDE_STYLE ('',( #59332 ) ) ; +#43960 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68367 ) ) ; +#43961 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#43962 = EDGE_CURVE ( 'NONE', #67142, #91942, #28061, .T. ) ; +#43964 = EDGE_CURVE ( 'NONE', #82841, #59639, #63408, .T. ) ; +#43963 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61918 ) ) ; +#43965 = ORIENTED_EDGE ( 'NONE', *, *, #44041, .T. ) ; +#43966 = ORIENTED_EDGE ( 'NONE', *, *, #74459, .T. ) ; +#43967 = MANIFOLD_SOLID_BREP ( 'ÊäÈë180', #45098 ) ; +#43968 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60186, 'distance_accuracy_value', 'NONE'); +#43969 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13899, 'distance_accuracy_value', 'NONE'); +#43970 = EDGE_CURVE ( 'NONE', #51353, #95765, #35844, .T. ) ; +#43971 = ADVANCED_FACE ( 'NONE', ( #41479 ), #82782, .T. ) ; +#43972 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#43973 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43974 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#43975 = PRESENTATION_STYLE_ASSIGNMENT (( #57838 ) ) ; +#43976 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#43977 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#43978 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#43979 = CYLINDRICAL_SURFACE ( 'NONE', #14637, 0.9754790742981810370 ) ; +#43980 = ORIENTED_EDGE ( 'NONE', *, *, #36282, .F. ) ; +#43981 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999989964, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#43982 = FILL_AREA_STYLE_COLOUR ( '', #77035 ) ; +#43983 = ORIENTED_EDGE ( 'NONE', *, *, #16945, .F. ) ; +#43984 = LINE ( 'NONE', #66968, #29402 ) ; +#43985 = ADVANCED_FACE ( 'NONE', ( #22489 ), #43587, .T. ) ; +#43986 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23632, #78263, #61449, #84889 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#43987 = VECTOR ( 'NONE', #67449, 1000.000000000000000 ) ; +#43988 = ORIENTED_EDGE ( 'NONE', *, *, #20088, .T. ) ; +#43989 = ADVANCED_FACE ( 'NONE', ( #99991 ), #53651, .T. ) ; +#43990 = FILL_AREA_STYLE ('',( #29663 ) ) ; +#43991 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43992 = AXIS2_PLACEMENT_3D ( 'NONE', #49970, #94854, #95357 ) ; +#43993 = STYLED_ITEM ( 'NONE', ( #97611 ), #93137 ) ; +#43994 = LINE ( 'NONE', #5650, #52790 ) ; +#43995 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#43996 = ORIENTED_EDGE ( 'NONE', *, *, #62097, .T. ) ; +#43997 = VECTOR ( 'NONE', #64260, 1000.000000000000000 ) ; +#43998 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#43999 = STYLED_ITEM ( 'NONE', ( #72765 ), #85262 ) ; +#44000 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44001 = VERTEX_POINT ( 'NONE', #93903 ) ; +#44002 = PRESENTATION_STYLE_ASSIGNMENT (( #21520 ) ) ; +#44003 = VECTOR ( 'NONE', #68514, 1000.000000000000000 ) ; +#44004 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44005 = VERTEX_POINT ( 'NONE', #23017 ) ; +#44006 = ORIENTED_EDGE ( 'NONE', *, *, #2159, .T. ) ; +#44007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44008 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#44009 = AXIS2_PLACEMENT_3D ( 'NONE', #66926, #52139, #29146 ) ; +#44010 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44011 = FILL_AREA_STYLE ('',( #69480 ) ) ; +#44012 = ORIENTED_EDGE ( 'NONE', *, *, #71278, .F. ) ; +#44013 = ORIENTED_EDGE ( 'NONE', *, *, #98599, .F. ) ; +#44014 = ORIENTED_EDGE ( 'NONE', *, *, #38454, .T. ) ; +#44015 = CONICAL_SURFACE ( 'NONE', #70093, 0.6999999999948158802, 0.7853981633974482790 ) ; +#44016 = ADVANCED_FACE ( 'NONE', ( #54675 ), #56186, .T. ) ; +#44017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97763 ), #53792 ) ; +#44018 = ORIENTED_EDGE ( 'NONE', *, *, #21825, .F. ) ; +#44019 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1629 ), #47236 ) ; +#44020 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.000000000000000000 ) ) ; +#44021 = FACE_OUTER_BOUND ( 'NONE', #4109, .T. ) ; +#44022 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44023 = PRESENTATION_STYLE_ASSIGNMENT (( #74688 ) ) ; +#44024 = ORIENTED_EDGE ( 'NONE', *, *, #39430, .F. ) ; +#44026 = ADVANCED_FACE ( 'NONE', ( #24038 ), #24559, .F. ) ; +#44025 = CARTESIAN_POINT ( 'NONE', ( -1.966666666666667007, -3.500000000000000000, 0.000000000000000000 ) ) ; +#44027 = FILL_AREA_STYLE_COLOUR ( '', #53317 ) ; +#44028 = FILL_AREA_STYLE_COLOUR ( '', #24822 ) ; +#44029 = VERTEX_POINT ( 'NONE', #18336 ) ; +#44030 = CARTESIAN_POINT ( 'NONE', ( 0.2376162505292615246, -1.418610517630681356, 0.8100000000000000533 ) ) ; +#44032 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44031 = LINE ( 'NONE', #82848, #798 ) ; +#44033 = LINE ( 'NONE', #46907, #17910 ) ; +#44034 = FACE_OUTER_BOUND ( 'NONE', #78517, .T. ) ; +#44035 = STYLED_ITEM ( 'NONE', ( #70838 ), #9968 ) ; +#44036 = CARTESIAN_POINT ( 'NONE', ( 1.775366595766979971, -1.422222704560690110, 0.8299999999999999600 ) ) ; +#44038 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44037 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#44039 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#44040 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44041 = EDGE_CURVE ( 'NONE', #54443, #43411, #33706, .T. ) ; +#44042 = ORIENTED_EDGE ( 'NONE', *, *, #33772, .T. ) ; +#44043 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55458 ) ) ; +#44044 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, 0.4849999999999998757, -0.2400000000000000189 ) ) ; +#44046 = CARTESIAN_POINT ( 'NONE', ( 1.592240980523089933, -1.399421068953929925, 0.8100000000000000533 ) ) ; +#44045 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8648700000000000276 ) ) ; +#44047 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#44048 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44049 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32258, #24632, #2622, #8662, #95505, #40937, #95002, #39912, #94507, #41435, #72068, #25131, #2123, #3118, #33265, #16894, #49098, #86369, #80240 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.382712307325918476E-05, 2.683571007987531730E-05, 3.927008175207105694E-05, 5.133161887827177055E-05, 6.299521226121036050E-05, 7.429237845692764780E-05, 8.536174655250618681E-05, 9.652160775091223803E-05, 0.0001077490236025269572, 0.0001190364376891015863, 0.0001307000310720401830, 0.0001426938147905748241, 0.0001549197910463055792, 0.0001672110464362091620, 0.0001797629478634983071, 0.0001926125413639715193 ), + .UNSPECIFIED. ) ; +#44050 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44051 = ORIENTED_EDGE ( 'NONE', *, *, #3849, .T. ) ; +#44052 = FILL_AREA_STYLE_COLOUR ( '', #40694 ) ; +#44053 = SURFACE_STYLE_USAGE ( .BOTH. , #60917 ) ; +#44054 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44055 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24582 ), #16328 ) ; +#44056 = VERTEX_POINT ( 'NONE', #34721 ) ; +#44057 = SURFACE_STYLE_USAGE ( .BOTH. , #13868 ) ; +#44059 = SURFACE_STYLE_FILL_AREA ( #42579 ) ; +#44058 = FACE_OUTER_BOUND ( 'NONE', #5053, .T. ) ; +#44060 = CARTESIAN_POINT ( 'NONE', ( 1.634048567103850047, -0.9784189978443861291, 0.8299999999999999600 ) ) ; +#44061 = EDGE_CURVE ( 'NONE', #88220, #15467, #51043, .T. ) ; +#44062 = PLANE ( 'NONE', #61661 ) ; +#44063 = PLANE ( 'NONE', #56177 ) ; +#44064 = AXIS2_PLACEMENT_3D ( 'NONE', #64977, #55338, #661 ) ; +#44065 = SURFACE_STYLE_USAGE ( .BOTH. , #5219 ) ; +#44066 = SURFACE_STYLE_USAGE ( .BOTH. , #11339 ) ; +#44067 = STYLED_ITEM ( 'NONE', ( #54142 ), #81533 ) ; +#44068 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000089, 2.523820061220085176, -0.02000000000000000042 ) ) ; +#44069 = ADVANCED_FACE ( 'NONE', ( #11112 ), #80679, .T. ) ; +#44070 = ORIENTED_EDGE ( 'NONE', *, *, #64841, .F. ) ; +#44071 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44072 = STYLED_ITEM ( 'NONE', ( #86456 ), #6576 ) ; +#44073 = PLANE ( 'NONE', #610 ) ; +#44074 = SURFACE_SIDE_STYLE ('',( #82893 ) ) ; +#44075 = FACE_OUTER_BOUND ( 'NONE', #59000, .T. ) ; +#44076 = CARTESIAN_POINT ( 'NONE', ( 5.696080500500175781, 3.570071499499825940, 0.8991599999999999593 ) ) ; +#44077 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44078 = FACE_OUTER_BOUND ( 'NONE', #79569, .T. ) ; +#44079 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44080 = LINE ( 'NONE', #84389, #48223 ) ; +#44081 = PRESENTATION_STYLE_ASSIGNMENT (( #66557 ) ) ; +#44082 = AXIS2_PLACEMENT_3D ( 'NONE', #44683, #66677, #68170 ) ; +#44083 = EDGE_CURVE ( 'NONE', #66042, #7270, #10602, .T. ) ; +#44084 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44085 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100469, 'distance_accuracy_value', 'NONE'); +#44086 = AXIS2_PLACEMENT_3D ( 'NONE', #48739, #72707, #95648 ) ; +#44087 = PRESENTATION_STYLE_ASSIGNMENT (( #74242 ) ) ; +#44088 = VECTOR ( 'NONE', #73239, 1000.000000000000000 ) ; +#44089 = ORIENTED_EDGE ( 'NONE', *, *, #4729, .F. ) ; +#44090 = SURFACE_SIDE_STYLE ('',( #45061 ) ) ; +#44091 = ORIENTED_EDGE ( 'NONE', *, *, #63770, .F. ) ; +#44093 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2878, 'distance_accuracy_value', 'NONE'); +#44092 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27807 ), #16289 ) ; +#44094 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14168, 'distance_accuracy_value', 'NONE'); +#44095 = ADVANCED_FACE ( 'NONE', ( #19871 ), #34222, .F. ) ; +#44096 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21489 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59942, #91044, #30238 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44097 = EDGE_CURVE ( 'NONE', #85305, #57125, #2047, .T. ) ; +#44098 = CARTESIAN_POINT ( 'NONE', ( 1.070765459575029999, -1.007957212727089935, 0.8100000000000000533 ) ) ; +#44099 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44100 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44101 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44102 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44103 = PLANE ( 'NONE', #86861 ) ; +#44104 = ORIENTED_EDGE ( 'NONE', *, *, #4219, .F. ) ; +#44105 = SURFACE_STYLE_USAGE ( .BOTH. , #83916 ) ; +#44106 = LINE ( 'NONE', #43103, #43704 ) ; +#44107 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15620, 'distance_accuracy_value', 'NONE'); +#44108 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, -0.01500000000000002720, 0.2458578643762690530 ) ) ; +#44109 = ADVANCED_FACE ( 'NONE', ( #65322 ), #88818, .T. ) ; +#44110 = FACE_OUTER_BOUND ( 'NONE', #25419, .T. ) ; +#44111 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14689 ), #40854 ) ; +#44112 = ORIENTED_EDGE ( 'NONE', *, *, #90670, .F. ) ; +#44113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76682 ), #27827 ) ; +#44114 = EDGE_CURVE ( 'NONE', #40477, #95463, #58648, .T. ) ; +#44115 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999994671, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#44116 = LINE ( 'NONE', #66593, #71914 ) ; +#44117 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44118 = ORIENTED_EDGE ( 'NONE', *, *, #74316, .T. ) ; +#44119 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, -0.6500000000000000222 ) ) ; +#44120 = FILL_AREA_STYLE_COLOUR ( '', #55480 ) ; +#44121 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37441, 'distance_accuracy_value', 'NONE'); +#44122 = FILL_AREA_STYLE_COLOUR ( '', #1927 ) ; +#44123 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.1000000000000016015, 6.729667010201685742E-79 ) ) ; +#44124 = ORIENTED_EDGE ( 'NONE', *, *, #72790, .T. ) ; +#44125 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31079 ), #39306 ) ; +#44126 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#44127 = CARTESIAN_POINT ( 'NONE', ( -1.076211927181194516, -1.244095395320582664, 0.8099999999998084288 ) ) ; +#44128 = ORIENTED_EDGE ( 'NONE', *, *, #64942, .T. ) ; +#44129 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#44130 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #83113 ) ; +#44131 = VECTOR ( 'NONE', #65638, 1000.000000000000000 ) ; +#44132 = MANIFOLD_SOLID_BREP ( 'ÊäÈë4', #9263 ) ; +#44133 = VERTEX_POINT ( 'NONE', #75017 ) ; +#44135 = EDGE_LOOP ( 'NONE', ( #43284, #41682, #85713, #48658 ) ) ; +#44134 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#44136 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68666 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21194, #52852, #75320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44138 = CARTESIAN_POINT ( 'NONE', ( -1.375607183049269988, -1.395425853902759972, 0.8100000000000000533 ) ) ; +#44139 = STYLED_ITEM ( 'NONE', ( #22924 ), #81871 ) ; +#44140 = PRESENTATION_STYLE_ASSIGNMENT (( #4825 ) ) ; +#44141 = EDGE_LOOP ( 'NONE', ( #32600, #8070, #22145, #44012 ) ) ; +#44143 = ADVANCED_FACE ( 'NONE', ( #92310 ), #12644, .T. ) ; +#44142 = SURFACE_SIDE_STYLE ('',( #51829 ) ) ; +#44144 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44145 = ORIENTED_EDGE ( 'NONE', *, *, #51194, .T. ) ; +#44146 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44147 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44148 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#44149 = ORIENTED_EDGE ( 'NONE', *, *, #16891, .T. ) ; +#44150 = VECTOR ( 'NONE', #44562, 1000.000000000000000 ) ; +#44151 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44152 = ORIENTED_EDGE ( 'NONE', *, *, #96736, .T. ) ; +#44153 = LINE ( 'NONE', #99678, #72782 ) ; +#44154 = SURFACE_STYLE_FILL_AREA ( #97736 ) ; +#44155 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44156 = FILL_AREA_STYLE ('',( #65642 ) ) ; +#44157 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44158 = VERTEX_POINT ( 'NONE', #93292 ) ; +#44159 = FILL_AREA_STYLE_COLOUR ( '', #61315 ) ; +#44160 = ORIENTED_EDGE ( 'NONE', *, *, #35218, .F. ) ; +#44161 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44162 = SURFACE_STYLE_USAGE ( .BOTH. , #12953 ) ; +#44163 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44164 = ADVANCED_FACE ( 'NONE', ( #8991 ), #15170, .T. ) ; +#44165 = PRESENTATION_STYLE_ASSIGNMENT (( #98712 ) ) ; +#44166 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #46160, #93624, #32405, #62559 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44167 = VECTOR ( 'NONE', #4077, 1000.000000000000000 ) ; +#44169 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44168 = AXIS2_PLACEMENT_3D ( 'NONE', #2206, #81344, #17490 ) ; +#44170 = PRESENTATION_STYLE_ASSIGNMENT (( #7304 ) ) ; +#44171 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#44172 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44173 = ORIENTED_EDGE ( 'NONE', *, *, #244, .T. ) ; +#44174 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.1499999999999999667, -0.01999999999999999695 ) ) ; +#44177 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#44176 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44175 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#44178 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44179 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44180 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#44181 = SHAPE_REPRESENTATION ( 'uid__2482', ( #82894 ), #7788 ) ; +#44182 = PLANE ( 'NONE', #61478 ) ; +#44183 = EDGE_CURVE ( 'NONE', #62161, #65802, #77501, .T. ) ; +#44184 = ORIENTED_EDGE ( 'NONE', *, *, #51524, .T. ) ; +#44185 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#44186 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.000000000000000000 ) ) ; +#44187 = SURFACE_STYLE_FILL_AREA ( #82523 ) ; +#44188 = STYLED_ITEM ( 'NONE', ( #72189 ), #18157 ) ; +#44189 = STYLED_ITEM ( 'NONE', ( #76253 ), #33681 ) ; +#44190 = FACE_OUTER_BOUND ( 'NONE', #17538, .T. ) ; +#44191 = PLANE ( 'NONE', #75129 ) ; +#44192 = LINE ( 'NONE', #60073, #7552 ) ; +#44193 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44194 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76858 ), #36072 ) ; +#44195 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44196 = STYLED_ITEM ( 'NONE', ( #16050 ), #95526 ) ; +#44197 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#44198 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44199 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44200 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#44201 = SURFACE_STYLE_FILL_AREA ( #75359 ) ; +#44202 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44203 = EDGE_CURVE ( 'NONE', #3614, #36363, #55578, .T. ) ; +#44204 = SURFACE_STYLE_USAGE ( .BOTH. , #52395 ) ; +#44205 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98531, 'distance_accuracy_value', 'NONE'); +#44206 = AXIS2_PLACEMENT_3D ( 'NONE', #85878, #86387, #93989 ) ; +#44207 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44208 = CARTESIAN_POINT ( 'NONE', ( 0.2977727229355032201, -0.9015156528804947333, 0.8100000000000002753 ) ) ; +#44209 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#44210 = SURFACE_STYLE_FILL_AREA ( #20226 ) ; +#44211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44212 = VERTEX_POINT ( 'NONE', #55062 ) ; +#44213 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44214 = SURFACE_STYLE_USAGE ( .BOTH. , #43712 ) ; +#44215 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43976, 'distance_accuracy_value', 'NONE'); +#44216 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2132, 'distance_accuracy_value', 'NONE'); +#44217 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#44218 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44219 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35955 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87915, #49641, #96049 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44220 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.499999999999980016, 0.1829999999999999960 ) ) ; +#44221 = EDGE_CURVE ( 'NONE', #25343, #89045, #39712, .T. ) ; +#44222 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68487 ) ) ; +#44223 = ORIENTED_EDGE ( 'NONE', *, *, #67673, .T. ) ; +#44224 = STYLED_ITEM ( 'NONE', ( #95364 ), #2263 ) ; +#44225 = LINE ( 'NONE', #43232, #30923 ) ; +#44226 = ORIENTED_EDGE ( 'NONE', *, *, #60086, .F. ) ; +#44227 = LINE ( 'NONE', #75382, #11262 ) ; +#44228 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25207, 'distance_accuracy_value', 'NONE'); +#44229 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44230 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44231 = ORIENTED_EDGE ( 'NONE', *, *, #85655, .T. ) ; +#44232 = ORIENTED_EDGE ( 'NONE', *, *, #79873, .T. ) ; +#44233 = SURFACE_STYLE_FILL_AREA ( #84065 ) ; +#44234 = ORIENTED_EDGE ( 'NONE', *, *, #7732, .T. ) ; +#44236 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#44235 = VECTOR ( 'NONE', #36074, 1000.000000000000000 ) ; +#44237 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44238 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44239 = LINE ( 'NONE', #5412, #49810 ) ; +#44240 = ADVANCED_FACE ( 'NONE', ( #92783 ), #79031, .T. ) ; +#44241 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#44243 = VERTEX_POINT ( 'NONE', #24429 ) ; +#44242 = VERTEX_POINT ( 'NONE', #94314 ) ; +#44244 = EDGE_LOOP ( 'NONE', ( #18263, #92192, #56372, #28548 ) ) ; +#44245 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44246 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44248 = CARTESIAN_POINT ( 'NONE', ( 1.400599642212259965, -0.9920916311794309994, 0.8300000000000009592 ) ) ; +#44247 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44249 = EDGE_CURVE ( 'NONE', #59761, #68224, #47883, .T. ) ; +#44250 = FACE_OUTER_BOUND ( 'NONE', #22689, .T. ) ; +#44251 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#44252 = CARTESIAN_POINT ( 'NONE', ( -1.332669063737389914, -0.9509517096142480197, 0.8299999999999999600 ) ) ; +#44253 = EDGE_LOOP ( 'NONE', ( #26214, #28559, #18350, #46674 ) ) ; +#44254 = ORIENTED_EDGE ( 'NONE', *, *, #70045, .F. ) ; +#44255 = ORIENTED_EDGE ( 'NONE', *, *, #67109, .F. ) ; +#44256 = CARTESIAN_POINT ( 'NONE', ( 1.070634376467239912, -1.188596174736179956, 0.8100000000000000533 ) ) ; +#44257 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44258 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33170 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43836, #22885, #14658 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44260 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#44259 = SURFACE_STYLE_USAGE ( .BOTH. , #3972 ) ; +#44261 = FILL_AREA_STYLE_COLOUR ( '', #35861 ) ; +#44262 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#44263 = FILL_AREA_STYLE ('',( #90750 ) ) ; +#44264 = VECTOR ( 'NONE', #21438, 1000.000000000000000 ) ; +#44266 = VERTEX_POINT ( 'NONE', #17719 ) ; +#44265 = PRESENTATION_STYLE_ASSIGNMENT (( #74940 ) ) ; +#44267 = VECTOR ( 'NONE', #60538, 1000.000000000000000 ) ; +#44268 = LINE ( 'NONE', #36151, #100312 ) ; +#44269 = FACE_OUTER_BOUND ( 'NONE', #35, .T. ) ; +#44270 = FILL_AREA_STYLE_COLOUR ( '', #41733 ) ; +#44271 = ORIENTED_EDGE ( 'NONE', *, *, #78101, .T. ) ; +#44272 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44273 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8648700000000000276 ) ) ; +#44274 = ORIENTED_EDGE ( 'NONE', *, *, #7981, .T. ) ; +#44275 = ORIENTED_EDGE ( 'NONE', *, *, #61303, .F. ) ; +#44276 = CARTESIAN_POINT ( 'NONE', ( 0.3795945119668320267, -0.9004463214819089512, 0.8299999999999992939 ) ) ; +#44277 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50817 ) ) ; +#44278 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584397904, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#44279 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44280 = AXIS2_PLACEMENT_3D ( 'NONE', #60818, #39834, #49515 ) ; +#44281 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44282 = CARTESIAN_POINT ( 'NONE', ( 6.876948754069506009, 10.29465675407266900, 0.8991599999999999593 ) ) ; +#44283 = FILL_AREA_STYLE ('',( #85110 ) ) ; +#44284 = PLANE ( 'NONE', #12757 ) ; +#44285 = EDGE_LOOP ( 'NONE', ( #3848, #15894, #60250, #48933 ) ) ; +#44286 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44287 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#44288 = VERTEX_POINT ( 'NONE', #87690 ) ; +#44289 = MANIFOLD_SOLID_BREP ( 'ÊäÈë111', #4452 ) ; +#44290 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57390 ) ) ; +#44291 = CARTESIAN_POINT ( 'NONE', ( -0.07193707439540279747, -0.9683984092875530525, 0.8299999999999999600 ) ) ; +#44292 = PLANE ( 'NONE', #2739 ) ; +#44293 = FILL_AREA_STYLE_COLOUR ( '', #41980 ) ; +#44294 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51057 ) ) ; +#44295 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#44296 = EDGE_CURVE ( 'NONE', #76663, #6488, #33589, .T. ) ; +#44297 = ORIENTED_EDGE ( 'NONE', *, *, #89353, .F. ) ; +#44298 = ADVANCED_FACE ( 'NONE', ( #79540 ), #41743, .T. ) ; +#44299 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44300 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44301 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73620 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1791, #25780, #79904 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44302 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44303 = CARTESIAN_POINT ( 'NONE', ( 1.880917842042550081, -1.247909878090150082, 0.8100000000000000533 ) ) ; +#44304 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39076 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81232, #57250, #11165 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44305 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#44306 = LINE ( 'NONE', #74490, #42384 ) ; +#44307 = PLANE ( 'NONE', #72838 ) ; +#44308 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44309 = SURFACE_STYLE_FILL_AREA ( #22876 ) ; +#44311 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44310 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000003934, 0.2399999999999999911 ) ) ; +#44312 = CARTESIAN_POINT ( 'NONE', ( 1.237877634622789991, -0.9585098101514269997, 0.8299999999999995159 ) ) ; +#44313 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61718, 'distance_accuracy_value', 'NONE'); +#44314 = ORIENTED_EDGE ( 'NONE', *, *, #87764, .F. ) ; +#44315 = PLANE ( 'NONE', #45253 ) ; +#44316 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#44317 = LINE ( 'NONE', #75488, #31300 ) ; +#44318 = ORIENTED_EDGE ( 'NONE', *, *, #13355, .F. ) ; +#44319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44320 = LINE ( 'NONE', #5981, #70840 ) ; +#44321 = SURFACE_STYLE_FILL_AREA ( #21360 ) ; +#44322 = AXIS2_PLACEMENT_3D ( 'NONE', #46804, #67888, #76078 ) ; +#44323 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56746, 'distance_accuracy_value', 'NONE'); +#44324 = AXIS2_PLACEMENT_3D ( 'NONE', #49553, #26567, #87321 ) ; +#44325 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#44326 = CARTESIAN_POINT ( 'NONE', ( 1.357422422243649951, -0.9354145126045169123, 0.8100000000000305844 ) ) ; +#44327 = CARTESIAN_POINT ( 'NONE', ( 1.436415948408267695, -1.291309753989891673, 0.8099999999998063194 ) ) ; +#44328 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44329 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37876 ), #85083 ) ; +#44330 = EDGE_CURVE ( 'NONE', #25485, #81116, #49918, .T. ) ; +#44331 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44332 = ORIENTED_EDGE ( 'NONE', *, *, #83059, .F. ) ; +#44333 = FILL_AREA_STYLE ('',( #50048 ) ) ; +#44334 = FILL_AREA_STYLE_COLOUR ( '', #35332 ) ; +#44335 = FILL_AREA_STYLE ('',( #42864 ) ) ; +#44336 = PRESENTATION_STYLE_ASSIGNMENT (( #53039 ) ) ; +#44337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93438, 'distance_accuracy_value', 'NONE'); +#44338 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44339 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44340 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9999, 'distance_accuracy_value', 'NONE'); +#44341 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#44342 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#44343 = VERTEX_POINT ( 'NONE', #2937 ) ; +#44344 = ORIENTED_EDGE ( 'NONE', *, *, #7661, .T. ) ; +#44345 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49519, 'distance_accuracy_value', 'NONE'); +#44346 = VECTOR ( 'NONE', #16439, 1000.000000000000000 ) ; +#44347 = ORIENTED_EDGE ( 'NONE', *, *, #84203, .T. ) ; +#44348 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000031308, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#44349 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44350 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#44351 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#44352 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000005773, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#44353 = FILL_AREA_STYLE ('',( #13154 ) ) ; +#44354 = EDGE_CURVE ( 'NONE', #77521, #72772, #33069, .T. ) ; +#44355 = CARTESIAN_POINT ( 'NONE', ( -1.293097912083150058, -1.043393888298179917, 0.8100000000000000533 ) ) ; +#44356 = SURFACE_SIDE_STYLE ('',( #36241 ) ) ; +#44358 = ORIENTED_EDGE ( 'NONE', *, *, #34689, .T. ) ; +#44357 = EDGE_LOOP ( 'NONE', ( #82691, #12911, #53804, #73171 ) ) ; +#44359 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44360 = ORIENTED_EDGE ( 'NONE', *, *, #72091, .T. ) ; +#44362 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 1.149999999999999911, 0.000000000000000000 ) ) ; +#44361 = SURFACE_STYLE_USAGE ( .BOTH. , #13167 ) ; +#44363 = ORIENTED_EDGE ( 'NONE', *, *, #9950, .T. ) ; +#44364 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21497 ) ) ; +#44365 = EDGE_CURVE ( 'NONE', #60027, #81364, #58098, .T. ) ; +#44366 = ORIENTED_EDGE ( 'NONE', *, *, #68279, .T. ) ; +#44367 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999993516, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#44369 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#44368 = PLANE ( 'NONE', #83963 ) ; +#44370 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44371 = ORIENTED_EDGE ( 'NONE', *, *, #87459, .T. ) ; +#44372 = EDGE_CURVE ( 'NONE', #68885, #27116, #42248, .T. ) ; +#44373 = ORIENTED_EDGE ( 'NONE', *, *, #49355, .F. ) ; +#44374 = EDGE_LOOP ( 'NONE', ( #90205, #5784, #6588, #74612 ) ) ; +#44375 = FILL_AREA_STYLE ('',( #98441 ) ) ; +#44376 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44377 = ADVANCED_FACE ( 'NONE', ( #42736 ), #19231, .T. ) ; +#44378 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10058 ), #80284 ) ; +#44379 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44381 = EDGE_LOOP ( 'NONE', ( #32544, #96087, #57197, #34027 ) ) ; +#44380 = FILL_AREA_STYLE ('',( #52095 ) ) ; +#44382 = SURFACE_STYLE_USAGE ( .BOTH. , #12698 ) ; +#44383 = FILL_AREA_STYLE ('',( #100414 ) ) ; +#44384 = EDGE_LOOP ( 'NONE', ( #68254, #67926, #86327, #92587 ) ) ; +#44385 = CARTESIAN_POINT ( 'NONE', ( 0.01522189160443420189, -1.319025261726090026, 0.8299999999999999600 ) ) ; +#44386 = ORIENTED_EDGE ( 'NONE', *, *, #90198, .F. ) ; +#44387 = EDGE_LOOP ( 'NONE', ( #55172, #92454, #37915, #88233 ) ) ; +#44388 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94659, #87524, #2278, #40581 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44389 = SURFACE_STYLE_FILL_AREA ( #51104 ) ; +#44390 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24947 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20073, #80895, #26766 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44391 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30900 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73656, #25697, #17497 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44392 = SURFACE_SIDE_STYLE ('',( #83740 ) ) ; +#44393 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8470 ), #26517 ) ; +#44394 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#44395 = EDGE_CURVE ( 'NONE', #70863, #77426, #85351, .T. ) ; +#44396 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19940 ), #28117 ) ; +#44397 = FILL_AREA_STYLE ('',( #7034 ) ) ; +#44398 = CARTESIAN_POINT ( 'NONE', ( -2.433333333333333570, 3.500000000000000000, 0.000000000000000000 ) ) ; +#44400 = CARTESIAN_POINT ( 'NONE', ( 1.993397459621554901, 1.449999999999999956, -11.36999999999999922 ) ) ; +#44399 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#44401 = FILL_AREA_STYLE_COLOUR ( '', #24725 ) ; +#44402 = ORIENTED_EDGE ( 'NONE', *, *, #19604, .T. ) ; +#44403 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44404 = CARTESIAN_POINT ( 'NONE', ( -0.9443983742018540184, -1.435626150595060047, 0.8299999999999999600 ) ) ; +#44405 = ORIENTED_EDGE ( 'NONE', *, *, #73247, .F. ) ; +#44406 = VECTOR ( 'NONE', #85449, 1000.000000000000000 ) ; +#44407 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#44408 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45992 ) ) ; +#44409 = SURFACE_SIDE_STYLE ('',( #51630 ) ) ; +#44410 = SURFACE_STYLE_FILL_AREA ( #67885 ) ; +#44411 = VECTOR ( 'NONE', #9783, 1000.000000000000000 ) ; +#44413 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -1.566666666666666652, 0.000000000000000000 ) ) ; +#44412 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#44414 = STYLED_ITEM ( 'NONE', ( #14119 ), #8062 ) ; +#44415 = ADVANCED_FACE ( 'NONE', ( #20753 ), #14045, .T. ) ; +#44416 = EDGE_CURVE ( 'NONE', #48405, #28424, #52417, .T. ) ; +#44417 = FILL_AREA_STYLE ('',( #58308 ) ) ; +#44418 = CARTESIAN_POINT ( 'NONE', ( 4.396484687205134634, 1.437461308415600048, -11.91872433040479962 ) ) ; +#44419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44420 = VECTOR ( 'NONE', #87686, 1000.000000000000000 ) ; +#44421 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#44422 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#44423 = STYLED_ITEM ( 'NONE', ( #18473 ), #25592 ) ; +#44425 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44424 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#44426 = PRESENTATION_STYLE_ASSIGNMENT (( #75112 ) ) ; +#44427 = FACE_OUTER_BOUND ( 'NONE', #85553, .T. ) ; +#44428 = EDGE_CURVE ( 'NONE', #35132, #25891, #44225, .T. ) ; +#44429 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76142, 'distance_accuracy_value', 'NONE'); +#44430 = VERTEX_POINT ( 'NONE', #97326 ) ; +#44431 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#44432 = FACE_OUTER_BOUND ( 'NONE', #29099, .T. ) ; +#44433 = EDGE_CURVE ( 'NONE', #93922, #80733, #4906, .T. ) ; +#44434 = CARTESIAN_POINT ( 'NONE', ( 0.4433330302657357835, -1.153639545326998306, 0.8099999999999999423 ) ) ; +#44435 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11793 ) ) ; +#44436 = PRESENTATION_STYLE_ASSIGNMENT (( #21982 ) ) ; +#44437 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44438 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44439 = SURFACE_SIDE_STYLE ('',( #43462 ) ) ; +#44440 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44441 = ADVANCED_FACE ( 'NONE', ( #5883 ), #29421, .F. ) ; +#44442 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44443 = ORIENTED_EDGE ( 'NONE', *, *, #83856, .T. ) ; +#44444 = EDGE_CURVE ( 'NONE', #68594, #5182, #52921, .T. ) ; +#44445 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #441 ) ) ; +#44446 = ORIENTED_EDGE ( 'NONE', *, *, #65050, .F. ) ; +#44447 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#44448 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45258, 'distance_accuracy_value', 'NONE'); +#44449 = FILL_AREA_STYLE ('',( #52166 ) ) ; +#44450 = SURFACE_SIDE_STYLE ('',( #90433 ) ) ; +#44451 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44452 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79879, #47710, #80894, #33420 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44453 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#44454 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#44455 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44456 = PRESENTATION_STYLE_ASSIGNMENT (( #66959 ) ) ; +#44457 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44458 = ORIENTED_EDGE ( 'NONE', *, *, #45456, .T. ) ; +#44459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44461 = VERTEX_POINT ( 'NONE', #98287 ) ; +#44462 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44463 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, -0.1400000000000000133 ) ) ; +#44464 = ORIENTED_EDGE ( 'NONE', *, *, #32796, .F. ) ; +#44465 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75471 ), #57584 ) ; +#44466 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44467 = VECTOR ( 'NONE', #32190, 1000.000000000000000 ) ; +#44468 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91780 ) ) ; +#44469 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#44470 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44471 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44472 = EDGE_CURVE ( 'NONE', #23574, #63005, #85038, .T. ) ; +#44473 = LINE ( 'NONE', #14308, #26817 ) ; +#44475 = ORIENTED_EDGE ( 'NONE', *, *, #98185, .T. ) ; +#44474 = EDGE_LOOP ( 'NONE', ( #91493, #29662, #94963, #88984 ) ) ; +#44476 = STYLED_ITEM ( 'NONE', ( #19418 ), #59568 ) ; +#44477 = ORIENTED_EDGE ( 'NONE', *, *, #93847, .T. ) ; +#44478 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44479 = STYLED_ITEM ( 'NONE', ( #61267 ), #11396 ) ; +#44481 = CARTESIAN_POINT ( 'NONE', ( 2.033333333333326554, 3.500000000000000000, 0.000000000000000000 ) ) ; +#44480 = FILL_AREA_STYLE ('',( #52195 ) ) ; +#44482 = ORIENTED_EDGE ( 'NONE', *, *, #63571, .F. ) ; +#44483 = EDGE_CURVE ( 'NONE', #24225, #39373, #77891, .T. ) ; +#44484 = EDGE_CURVE ( 'NONE', #50963, #20599, #7859, .T. ) ; +#44485 = EDGE_LOOP ( 'NONE', ( #13828, #15123, #68107, #49958 ) ) ; +#44486 = FACE_OUTER_BOUND ( 'NONE', #39364, .T. ) ; +#44487 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44488 = CARTESIAN_POINT ( 'NONE', ( -0.5047968834700360397, -1.178195226781280081, 0.8299999999999999600 ) ) ; +#44489 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44490 = AXIS2_PLACEMENT_3D ( 'NONE', #93662, #40111, #1294 ) ; +#44492 = PRESENTATION_STYLE_ASSIGNMENT (( #21041 ) ) ; +#44491 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44493 = ORIENTED_EDGE ( 'NONE', *, *, #93032, .T. ) ; +#44494 = ADVANCED_FACE ( 'NONE', ( #86050 ), #78398, .F. ) ; +#44495 = ORIENTED_EDGE ( 'NONE', *, *, #83223, .F. ) ; +#44496 = EDGE_LOOP ( 'NONE', ( #35764, #6293, #16459, #5568 ) ) ; +#44497 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000000311, 0.1399999999999965994 ) ) ; +#44498 = EDGE_CURVE ( 'NONE', #45276, #52301, #30527, .T. ) ; +#44500 = VERTEX_POINT ( 'NONE', #23789 ) ; +#44499 = FILL_AREA_STYLE_COLOUR ( '', #60705 ) ; +#44501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44502 = FACE_OUTER_BOUND ( 'NONE', #43101, .T. ) ; +#44503 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#44504 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44505 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44506 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69432 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41372, #88827, #94448 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44507 = ORIENTED_EDGE ( 'NONE', *, *, #6738, .F. ) ; +#44508 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44509 = PRESENTATION_STYLE_ASSIGNMENT (( #14842 ) ) ; +#44510 = VERTEX_POINT ( 'NONE', #16081 ) ; +#44511 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25494, 'distance_accuracy_value', 'NONE'); +#44512 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44513 = AXIS2_PLACEMENT_3D ( 'NONE', #95029, #17927, #56803 ) ; +#44514 = FILL_AREA_STYLE ('',( #47430 ) ) ; +#44516 = EDGE_CURVE ( 'NONE', #22003, #69329, #63102, .T. ) ; +#44515 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44517 = EDGE_CURVE ( 'NONE', #84214, #38264, #8356, .T. ) ; +#44518 = FACE_OUTER_BOUND ( 'NONE', #3945, .T. ) ; +#44519 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44520 = CARTESIAN_POINT ( 'NONE', ( -0.1507735820217988021, -0.9630148790355518296, 0.8100000000003015899 ) ) ; +#44521 = AXIS2_PLACEMENT_3D ( 'NONE', #38523, #13452, #69637 ) ; +#44522 = ORIENTED_EDGE ( 'NONE', *, *, #60750, .F. ) ; +#44523 = LINE ( 'NONE', #30212, #54975 ) ; +#44524 = PRESENTATION_STYLE_ASSIGNMENT (( #13321 ) ) ; +#44525 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94878 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86008, #69663, #54387 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44526 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44527 = SURFACE_STYLE_FILL_AREA ( #66035 ) ; +#44529 = SURFACE_STYLE_USAGE ( .BOTH. , #83372 ) ; +#44528 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44531 = STYLED_ITEM ( 'NONE', ( #52788 ), #21200 ) ; +#44530 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#44532 = PRESENTATION_STYLE_ASSIGNMENT (( #76693 ) ) ; +#44533 = SURFACE_STYLE_FILL_AREA ( #13329 ) ; +#44534 = EDGE_CURVE ( 'NONE', #37519, #92811, #99744, .T. ) ; +#44535 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59263 ), #54335 ) ; +#44536 = AXIS2_PLACEMENT_3D ( 'NONE', #24473, #63274, #48944 ) ; +#44537 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59470 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69793, #29985, #31009 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44538 = ORIENTED_EDGE ( 'NONE', *, *, #76163, .T. ) ; +#44539 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77200 ) ) ; +#44540 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20687, #50857, #21190, #43657 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44541 = FACE_OUTER_BOUND ( 'NONE', #24619, .T. ) ; +#44543 = AXIS2_PLACEMENT_3D ( 'NONE', #92614, #37043, #75323 ) ; +#44542 = FILL_AREA_STYLE ('',( #52254 ) ) ; +#44544 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90191 ) ) ; +#44545 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44546 = VERTEX_POINT ( 'NONE', #23277 ) ; +#44547 = LINE ( 'NONE', #6201, #64033 ) ; +#44549 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44548 = CARTESIAN_POINT ( 'NONE', ( 1.644292209069110111, -0.9726617844338859564, 0.8100000000000000533 ) ) ; +#44550 = FILL_AREA_STYLE ('',( #59443 ) ) ; +#44551 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85303 ), #75553 ) ; +#44552 = STYLED_ITEM ( 'NONE', ( #89735 ), #11524 ) ; +#44553 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94823, #55591, #40755, #25950 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44554 = FACE_OUTER_BOUND ( 'NONE', #70408, .T. ) ; +#44555 = VERTEX_POINT ( 'NONE', #68698 ) ; +#44556 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44557 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44558 = LINE ( 'NONE', #67536, #91692 ) ; +#44559 = CARTESIAN_POINT ( 'NONE', ( 0.9689116169396260192, -1.374349516767729984, 0.8300000000000010703 ) ) ; +#44560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94017 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34984, #51797, #36475 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44561 = FILL_AREA_STYLE ('',( #5741 ) ) ; +#44562 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44563 = SURFACE_STYLE_FILL_AREA ( #45056 ) ; +#44564 = SURFACE_STYLE_USAGE ( .BOTH. , #12867 ) ; +#44565 = SURFACE_STYLE_USAGE ( .BOTH. , #7703 ) ; +#44566 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#44567 = ORIENTED_EDGE ( 'NONE', *, *, #19658, .F. ) ; +#44568 = EDGE_CURVE ( 'NONE', #65277, #12846, #54434, .T. ) ; +#44569 = VECTOR ( 'NONE', #61147, 1000.000000000000000 ) ; +#44570 = ORIENTED_EDGE ( 'NONE', *, *, #82156, .F. ) ; +#44571 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44572 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#44573 = CYLINDRICAL_SURFACE ( 'NONE', #15551, 0.05000000000000002359 ) ; +#44574 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.50000000000000000, 0.000000000000000000 ) ) ; +#44576 = EDGE_CURVE ( 'NONE', #100905, #65764, #64572, .T. ) ; +#44575 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#44577 = CARTESIAN_POINT ( 'NONE', ( 0.5444371223934474369, -1.018231029507710828, 0.8100000000000003864 ) ) ; +#44578 = ORIENTED_EDGE ( 'NONE', *, *, #39717, .T. ) ; +#44579 = FILL_AREA_STYLE ('',( #21628 ) ) ; +#44580 = FACE_OUTER_BOUND ( 'NONE', #67796, .T. ) ; +#44581 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6257 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32896, #87509, #78354 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44582 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.900000000000000133, -1.507334416018511324E-89 ) ) ; +#44583 = EDGE_LOOP ( 'NONE', ( #30929, #42238, #96476, #77877 ) ) ; +#44584 = LINE ( 'NONE', #4794, #34755 ) ; +#44585 = VECTOR ( 'NONE', #51547, 1000.000000000000000 ) ; +#44586 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96767 ), #80490 ) ; +#44587 = CARTESIAN_POINT ( 'NONE', ( 1.408848379044900012, -1.435626150595060047, 0.8299999999999994049 ) ) ; +#44588 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.899999999999978817, -0.02000000000000000042 ) ) ; +#44589 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#44590 = ADVANCED_FACE ( 'NONE', ( #46727 ), #8862, .T. ) ; +#44591 = VECTOR ( 'NONE', #8551, 1000.000000000000000 ) ; +#44592 = VERTEX_POINT ( 'NONE', #95191 ) ; +#44593 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 0.1000000000000000056, -11.57000000000000028 ) ) ; +#44594 = FILL_AREA_STYLE ('',( #44120 ) ) ; +#44595 = PLANE ( 'NONE', #2204 ) ; +#44596 = PRESENTATION_STYLE_ASSIGNMENT (( #6734 ) ) ; +#44597 = SURFACE_STYLE_USAGE ( .BOTH. , #58498 ) ; +#44598 = EDGE_CURVE ( 'NONE', #95472, #9281, #51206, .T. ) ; +#44599 = ORIENTED_EDGE ( 'NONE', *, *, #30732, .T. ) ; +#44601 = AXIS2_PLACEMENT_3D ( 'NONE', #20194, #83510, #66661 ) ; +#44600 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10280 ) ) ; +#44602 = STYLED_ITEM ( 'NONE', ( #20326 ), #19270 ) ; +#44603 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44604 = FILL_AREA_STYLE_COLOUR ( '', #41616 ) ; +#44605 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44606 = DIRECTION ( 'NONE', ( 0.7071067811865472397, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#44607 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8648700000000000276 ) ) ; +#44608 = CARTESIAN_POINT ( 'NONE', ( 1.525795062450169937, -1.430103682213279992, 0.8300000000000001821 ) ) ; +#44609 = VERTEX_POINT ( 'NONE', #18087 ) ; +#44610 = PRESENTATION_STYLE_ASSIGNMENT (( #69068 ) ) ; +#44611 = STYLED_ITEM ( 'NONE', ( #49225 ), #61284 ) ; +#44612 = AXIS2_PLACEMENT_3D ( 'NONE', #59495, #68585, #43601 ) ; +#44613 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #9811, #19566, #96139, #64531 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44614 = EDGE_CURVE ( 'NONE', #54213, #61427, #87572, .T. ) ; +#44615 = ORIENTED_EDGE ( 'NONE', *, *, #100087, .F. ) ; +#44616 = ORIENTED_EDGE ( 'NONE', *, *, #63429, .F. ) ; +#44617 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37660, 'distance_accuracy_value', 'NONE'); +#44618 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000201086, 0.000000000000000000 ) ) ; +#44620 = CARTESIAN_POINT ( 'NONE', ( -1.263740750452060135, -1.495173285438690103, 0.8299999999999999600 ) ) ; +#44619 = SURFACE_STYLE_USAGE ( .BOTH. , #29812 ) ; +#44621 = FACE_OUTER_BOUND ( 'NONE', #89972, .T. ) ; +#44622 = PLANE ( 'NONE', #53696 ) ; +#44623 = EDGE_LOOP ( 'NONE', ( #58650, #16224, #14707, #52965 ) ) ; +#44625 = EDGE_CURVE ( 'NONE', #32892, #70891, #33980, .T. ) ; +#44624 = FACE_OUTER_BOUND ( 'NONE', #1119, .T. ) ; +#44626 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44627 = EDGE_LOOP ( 'NONE', ( #40875, #46371, #53454, #16740, #46636, #46718, #48444, #58019, #38333, #90861, #92309, #32221, #46106, #10094, #43635, #7907, #4953, #37359, #90460, #24970, #96013, #26216, #15176, #44318, #93807, #67684, #18971, #61376, #90494, #91102, #55448, #45890, #79604, #56346, #31714, #96976, #18646, #41371, #10228, #4697, #642, #92261, #69764, #81121, #4074, #76673, #16216, #52661, #84687, #74931, #60598, #15212, #4370, #56410, #59941, #21029, #73944, #29719, #18216, #94749 ) ) ; +#44628 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8099999999999999423 ) ) ; +#44629 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#44630 = FILL_AREA_STYLE_COLOUR ( '', #82365 ) ; +#44631 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#44632 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65430 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45455, #22010, #69454 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44633 = ORIENTED_EDGE ( 'NONE', *, *, #19499, .T. ) ; +#44635 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#44634 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44636 = ORIENTED_EDGE ( 'NONE', *, *, #10507, .F. ) ; +#44637 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44638 = ADVANCED_FACE ( 'NONE', ( #50323 ), #26312, .F. ) ; +#44639 = EDGE_CURVE ( 'NONE', #65827, #59395, #71238, .T. ) ; +#44640 = FACE_OUTER_BOUND ( 'NONE', #9290, .T. ) ; +#44641 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44642 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#44643 = STYLED_ITEM ( 'NONE', ( #47563 ), #71132 ) ; +#44644 = EDGE_CURVE ( 'NONE', #86070, #47158, #71757, .T. ) ; +#44645 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44646 = ADVANCED_FACE ( 'NONE', ( #80948 ), #42128, .T. ) ; +#44647 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #43343, #37221, #59220, #29534 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44648 = SURFACE_STYLE_USAGE ( .BOTH. , #43650 ) ; +#44649 = ORIENTED_EDGE ( 'NONE', *, *, #91994, .F. ) ; +#44650 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#44651 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96758 ), #2280 ) ; +#44652 = ORIENTED_EDGE ( 'NONE', *, *, #15984, .F. ) ; +#44654 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44653 = SURFACE_STYLE_USAGE ( .BOTH. , #99210 ) ; +#44655 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44656 = EDGE_CURVE ( 'NONE', #3165, #31723, #68076, .T. ) ; +#44657 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18619 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30470, #100331, #85126 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44659 = AXIS2_PLACEMENT_3D ( 'NONE', #10221, #33830, #87425 ) ; +#44658 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#44660 = STYLED_ITEM ( 'NONE', ( #47392 ), #26600 ) ; +#44661 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44662 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.1000000000000000056, -11.41999999999999993 ) ) ; +#44663 = EDGE_CURVE ( 'NONE', #87470, #14577, #67579, .T. ) ; +#44664 = ORIENTED_EDGE ( 'NONE', *, *, #69304, .F. ) ; +#44665 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44666 = VECTOR ( 'NONE', #20190, 1000.000000000000000 ) ; +#44667 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9986, 'distance_accuracy_value', 'NONE'); +#44668 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44669 = VECTOR ( 'NONE', #3635, 1000.000000000000000 ) ; +#44670 = VECTOR ( 'NONE', #80531, 1000.000000000000114 ) ; +#44671 = FILL_AREA_STYLE_COLOUR ( '', #69706 ) ; +#44672 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49613 ) ) ; +#44673 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44674 = ORIENTED_EDGE ( 'NONE', *, *, #46150, .F. ) ; +#44676 = STYLED_ITEM ( 'NONE', ( #42895 ), #38132 ) ; +#44675 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#44677 = CARTESIAN_POINT ( 'NONE', ( -0.0005258701502700120420, -1.389839611604140046, 0.8299999999999999600 ) ) ; +#44678 = CIRCLE ( 'NONE', #96863, 0.009999999999999998473 ) ; +#44679 = SURFACE_SIDE_STYLE ('',( #15534 ) ) ; +#44680 = FILL_AREA_STYLE_COLOUR ( '', #51265 ) ; +#44681 = LINE ( 'NONE', #14518, #18736 ) ; +#44682 = FILL_AREA_STYLE_COLOUR ( '', #49048 ) ; +#44683 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#44684 = LINE ( 'NONE', #14017, #11959 ) ; +#44685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44686 = VECTOR ( 'NONE', #93047, 1000.000000000000000 ) ; +#44687 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65941 ) ) ; +#44688 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44689 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.000000000000000000 ) ) ; +#44690 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44691 = ADVANCED_FACE ( 'NONE', ( #34986 ), #75273, .T. ) ; +#44692 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44693 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#44694 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44695 = STYLED_ITEM ( 'NONE', ( #63539 ), #11929 ) ; +#44696 = FILL_AREA_STYLE ('',( #91670 ) ) ; +#44697 = SURFACE_STYLE_FILL_AREA ( #91188 ) ; +#44698 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31677 ), #96884 ) ; +#44700 = EDGE_CURVE ( 'NONE', #38519, #78286, #73763, .T. ) ; +#44699 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.900000000000000133, -0.02000000000000000042 ) ) ; +#44701 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44702 = ORIENTED_EDGE ( 'NONE', *, *, #12128, .T. ) ; +#44703 = SURFACE_SIDE_STYLE ('',( #83542 ) ) ; +#44704 = LINE ( 'NONE', #82546, #9306 ) ; +#44705 = FILL_AREA_STYLE_COLOUR ( '', #36184 ) ; +#44706 = VECTOR ( 'NONE', #72774, 1000.000000000000000 ) ; +#44707 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#44708 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#44709 = PLANE ( 'NONE', #485 ) ; +#44710 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44711 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44712 = SURFACE_STYLE_USAGE ( .BOTH. , #68199 ) ; +#44713 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87168 ) ) ; +#44714 = ORIENTED_EDGE ( 'NONE', *, *, #77495, .F. ) ; +#44715 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44716 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44717 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#44718 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#44719 = ORIENTED_EDGE ( 'NONE', *, *, #42155, .T. ) ; +#44720 = ORIENTED_EDGE ( 'NONE', *, *, #57611, .T. ) ; +#44721 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60481 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72324, #33030, #86649 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44723 = DIRECTION ( 'NONE', ( 1.166666699999935221E-05, -0.9999999999319444388, 0.000000000000000000 ) ) ; +#44722 = CARTESIAN_POINT ( 'NONE', ( 0.4673939658190879864, -1.066920424575050097, 0.8300000000000002931 ) ) ; +#44724 = EDGE_LOOP ( 'NONE', ( #6181, #42272, #94003, #58764 ) ) ; +#44725 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44726 = CARTESIAN_POINT ( 'NONE', ( 0.5268964082245309877, -1.158245412001609909, 0.8299999999999999600 ) ) ; +#44727 = AXIS2_PLACEMENT_3D ( 'NONE', #1550, #80176, #86810 ) ; +#44728 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78362 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9793, #70134, #42545 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44729 = SURFACE_STYLE_USAGE ( .BOTH. , #21773 ) ; +#44730 = FILL_AREA_STYLE_COLOUR ( '', #87250 ) ; +#44731 = VERTEX_POINT ( 'NONE', #42623 ) ; +#44732 = ORIENTED_EDGE ( 'NONE', *, *, #49304, .T. ) ; +#44733 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#44734 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44735 = AXIS2_PLACEMENT_3D ( 'NONE', #12596, #43810, #37178 ) ; +#44737 = STYLED_ITEM ( 'NONE', ( #53889 ), #20174 ) ; +#44736 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75108, 'distance_accuracy_value', 'NONE'); +#44738 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61740, #92341, #30531, #22928 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#44739 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44741 = PLANE ( 'NONE', #93648 ) ; +#44740 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#44742 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#44743 = AXIS2_PLACEMENT_3D ( 'NONE', #12240, #43961, #4643 ) ; +#44744 = SURFACE_STYLE_USAGE ( .BOTH. , #75914 ) ; +#44745 = FACE_OUTER_BOUND ( 'NONE', #85732, .T. ) ; +#44746 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44747 = CARTESIAN_POINT ( 'NONE', ( -1.371243692415410331, -1.052663393014950044, 0.8299999999999999600 ) ) ; +#44748 = ORIENTED_EDGE ( 'NONE', *, *, #38427, .T. ) ; +#44749 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44750 = ORIENTED_EDGE ( 'NONE', *, *, #75869, .F. ) ; +#44751 = EDGE_LOOP ( 'NONE', ( #50390, #54436, #14961, #29207 ) ) ; +#44752 = CARTESIAN_POINT ( 'NONE', ( 1.016962903650600047, -1.153389236204189983, 0.8100000000000000533 ) ) ; +#44753 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44754 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8648700000000000276 ) ) ; +#44755 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#44756 = SURFACE_STYLE_FILL_AREA ( #44263 ) ; +#44758 = ORIENTED_EDGE ( 'NONE', *, *, #7414, .F. ) ; +#44757 = SURFACE_STYLE_FILL_AREA ( #99325 ) ; +#44759 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3978 ), #64328 ) ; +#44760 = ADVANCED_FACE ( 'NONE', ( #51300 ), #99157, .F. ) ; +#44761 = VECTOR ( 'NONE', #49096, 1000.000000000000114 ) ; +#44762 = PRESENTATION_STYLE_ASSIGNMENT (( #21303 ) ) ; +#44763 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44764 = ORIENTED_EDGE ( 'NONE', *, *, #23756, .T. ) ; +#44765 = LINE ( 'NONE', #51487, #95440 ) ; +#44766 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000007994, -3.149999999999979927, 0.000000000000000000 ) ) ; +#44767 = ORIENTED_EDGE ( 'NONE', *, *, #10812, .T. ) ; +#44768 = ORIENTED_EDGE ( 'NONE', *, *, #74510, .T. ) ; +#44769 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#44770 = SURFACE_SIDE_STYLE ('',( #76436 ) ) ; +#44771 = LINE ( 'NONE', #75440, #13807 ) ; +#44772 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17444 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30283, #38481, #72641 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44773 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#44774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85542 ) ) ; +#44775 = LINE ( 'NONE', #70285, #38090 ) ; +#44776 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44777 = EDGE_CURVE ( 'NONE', #1838, #67005, #24051, .T. ) ; +#44778 = ORIENTED_EDGE ( 'NONE', *, *, #27878, .T. ) ; +#44779 = SURFACE_SIDE_STYLE ('',( #42811 ) ) ; +#44780 = EDGE_LOOP ( 'NONE', ( #3501, #27353, #95076, #98706 ) ) ; +#44781 = VECTOR ( 'NONE', #8937, 1000.000000000000000 ) ; +#44782 = MANIFOLD_SOLID_BREP ( 'ÊäÈë164', #64961 ) ; +#44783 = CARTESIAN_POINT ( 'NONE', ( -0.009357855636228630536, -1.039339352017210061, 0.8100000000000000533 ) ) ; +#44784 = LINE ( 'NONE', #93744, #53333 ) ; +#44785 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44786 = VECTOR ( 'NONE', #56951, 1000.000000000000000 ) ; +#44787 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61096 ) ) ; +#44788 = SURFACE_SIDE_STYLE ('',( #20322 ) ) ; +#44789 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#44790 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44791 = ORIENTED_EDGE ( 'NONE', *, *, #35753, .T. ) ; +#44792 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44793 = PLANE ( 'NONE', #34221 ) ; +#44794 = AXIS2_PLACEMENT_3D ( 'NONE', #13286, #60379, #5168 ) ; +#44795 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58493 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97172, #56928, #58449 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44796 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#44797 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71146 ), #67836 ) ; +#44798 = STYLED_ITEM ( 'NONE', ( #36217 ), #48208 ) ; +#44799 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74210 ), #48116 ) ; +#44800 = CARTESIAN_POINT ( 'NONE', ( 1.880917842042550081, -1.247909878090150082, 0.8299999999999999600 ) ) ; +#44801 = SURFACE_SIDE_STYLE ('',( #53012 ) ) ; +#44802 = ADVANCED_FACE ( 'NONE', ( #78641 ), #63860, .F. ) ; +#44803 = FILL_AREA_STYLE ('',( #38189 ) ) ; +#44805 = FILL_AREA_STYLE ('',( #13615 ) ) ; +#44804 = VECTOR ( 'NONE', #14822, 1000.000000000000000 ) ; +#44806 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44807 = FILL_AREA_STYLE_COLOUR ( '', #87875 ) ; +#44808 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 2.100000000000000089, 0.000000000000000000 ) ) ; +#44809 = FILL_AREA_STYLE ('',( #52511 ) ) ; +#44810 = ORIENTED_EDGE ( 'NONE', *, *, #5371, .F. ) ; +#44811 = SURFACE_STYLE_USAGE ( .BOTH. , #60205 ) ; +#44813 = ADVANCED_FACE ( 'NONE', ( #56203 ), #17354, .F. ) ; +#44812 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44814 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#44815 = ORIENTED_EDGE ( 'NONE', *, *, #45569, .F. ) ; +#44816 = SURFACE_STYLE_FILL_AREA ( #13626 ) ; +#44817 = SURFACE_STYLE_USAGE ( .BOTH. , #20357 ) ; +#44818 = AXIS2_PLACEMENT_3D ( 'NONE', #39656, #23342, #86108 ) ; +#44819 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#44820 = PRESENTATION_STYLE_ASSIGNMENT (( #22891 ) ) ; +#44821 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#44822 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44823 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44824 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44825 = FILL_AREA_STYLE ('',( #36210 ) ) ; +#44826 = VERTEX_POINT ( 'NONE', #96458 ) ; +#44827 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44828 = CIRCLE ( 'NONE', #4126, 0.01000000000000002623 ) ; +#44829 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44830 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#44831 = PLANE ( 'NONE', #47756 ) ; +#44832 = DIRECTION ( 'NONE', ( -0.3387340427540271870, 0.000000000000000000, -0.9408821649279535126 ) ) ; +#44833 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#44834 = ADVANCED_FACE ( 'NONE', ( #57219 ), #11131, .F. ) ; +#44835 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.185754870129869909, 0.8099999999999875078 ) ) ; +#44836 = VERTEX_POINT ( 'NONE', #35246 ) ; +#44837 = ORIENTED_EDGE ( 'NONE', *, *, #11837, .F. ) ; +#44838 = FILL_AREA_STYLE ('',( #36724 ) ) ; +#44839 = ORIENTED_EDGE ( 'NONE', *, *, #94841, .T. ) ; +#44840 = SURFACE_STYLE_USAGE ( .BOTH. , #53549 ) ; +#44841 = VECTOR ( 'NONE', #54744, 1000.000000000000000 ) ; +#44842 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#44843 = LINE ( 'NONE', #66849, #7424 ) ; +#44844 = LINE ( 'NONE', #76510, #33386 ) ; +#44845 = SURFACE_STYLE_USAGE ( .BOTH. , #98913 ) ; +#44846 = CARTESIAN_POINT ( 'NONE', ( -0.8909255146275300019, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#44847 = CARTESIAN_POINT ( 'NONE', ( -0.05380371811523915887, 0.7626265873953500529, 0.8100000000000002753 ) ) ; +#44848 = AXIS2_PLACEMENT_3D ( 'NONE', #77991, #70315, #86137 ) ; +#44850 = ORIENTED_EDGE ( 'NONE', *, *, #59359, .T. ) ; +#44849 = VERTEX_POINT ( 'NONE', #3576 ) ; +#44851 = EDGE_LOOP ( 'NONE', ( #43347, #33218, #13449, #60277, #32218, #4463, #41247, #87676 ) ) ; +#44852 = CARTESIAN_POINT ( 'NONE', ( 1.525294525926170097, -1.013847726018640039, 0.8099999999999981659 ) ) ; +#44853 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15460 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27183, #49149, #12250 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44854 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86767, 'distance_accuracy_value', 'NONE'); +#44855 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98803 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46284, #7432, #70806 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44856 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -2.299999999999999822, 0.1829999999999500082 ) ) ; +#44857 = ORIENTED_EDGE ( 'NONE', *, *, #81403, .T. ) ; +#44858 = EDGE_CURVE ( 'NONE', #32846, #53201, #27074, .T. ) ; +#44860 = ORIENTED_EDGE ( 'NONE', *, *, #64379, .T. ) ; +#44859 = AXIS2_PLACEMENT_3D ( 'NONE', #48317, #71772, #17618 ) ; +#44861 = ADVANCED_FACE ( 'NONE', ( #81699 ), #42985, .T. ) ; +#44862 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#44863 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#44864 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79101 ) ) ; +#44865 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#44867 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#44866 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44868 = PRESENTATION_STYLE_ASSIGNMENT (( #82707 ) ) ; +#44869 = VERTEX_POINT ( 'NONE', #2692 ) ; +#44870 = STYLED_ITEM ( 'NONE', ( #15050 ), #48613 ) ; +#44871 = PRESENTATION_STYLE_ASSIGNMENT (( #62755 ) ) ; +#44872 = EDGE_LOOP ( 'NONE', ( #34655, #28183, #87217, #89376, #23336, #18684 ) ) ; +#44873 = ORIENTED_EDGE ( 'NONE', *, *, #7446, .T. ) ; +#44874 = VECTOR ( 'NONE', #54190, 1000.000000000000000 ) ; +#44875 = FILL_AREA_STYLE ('',( #88486 ) ) ; +#44876 = ORIENTED_EDGE ( 'NONE', *, *, #54450, .F. ) ; +#44877 = FACE_OUTER_BOUND ( 'NONE', #40925, .T. ) ; +#44878 = ADVANCED_FACE ( 'NONE', ( #41495 ), #26687, .T. ) ; +#44879 = SURFACE_STYLE_FILL_AREA ( #13699 ) ; +#44880 = ORIENTED_EDGE ( 'NONE', *, *, #2104, .T. ) ; +#44881 = ORIENTED_EDGE ( 'NONE', *, *, #82716, .F. ) ; +#44882 = ORIENTED_EDGE ( 'NONE', *, *, #22203, .F. ) ; +#44883 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44884 = LINE ( 'NONE', #31109, #2541 ) ; +#44886 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#44885 = VECTOR ( 'NONE', #70518, 1000.000000000000000 ) ; +#44887 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#44888 = VECTOR ( 'NONE', #94541, 1000.000000000000000 ) ; +#44889 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99439 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73201, #89521, #50736 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44890 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5610 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9083, #24011, #1518 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44891 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44892 = EDGE_CURVE ( 'NONE', #38479, #96313, #3675, .T. ) ; +#44893 = PRESENTATION_STYLE_ASSIGNMENT (( #45889 ) ) ; +#44894 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 2.827608999999999817, 0.8648700000000000276 ) ) ; +#44895 = ORIENTED_EDGE ( 'NONE', *, *, #33619, .T. ) ; +#44896 = FILL_AREA_STYLE_COLOUR ( '', #99941 ) ; +#44897 = ORIENTED_EDGE ( 'NONE', *, *, #55686, .F. ) ; +#44898 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28608 ) ) ; +#44900 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17105 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89954, #33854, #33343 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44899 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#44902 = PLANE ( 'NONE', #44322 ) ; +#44901 = LINE ( 'NONE', #90910, #85347 ) ; +#44903 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#44904 = PLANE ( 'NONE', #61520 ) ; +#44905 = FILL_AREA_STYLE_COLOUR ( '', #18876 ) ; +#44906 = SURFACE_STYLE_USAGE ( .BOTH. , #13220 ) ; +#44907 = CARTESIAN_POINT ( 'NONE', ( -1.321337043985290061, -1.462480703074420019, 0.8300000000000024025 ) ) ; +#44908 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44909 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000001929, 0.2500000000000000555, 0.5799137866959190868 ) ) ; +#44910 = PLANE ( 'NONE', #47346 ) ; +#44911 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#44912 = EDGE_CURVE ( 'NONE', #31593, #38134, #49160, .T. ) ; +#44913 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#44914 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4142 ) ) ; +#44915 = SURFACE_SIDE_STYLE ('',( #37800 ) ) ; +#44916 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44917 = CIRCLE ( 'NONE', #71054, 0.009999999999999998473 ) ; +#44918 = STYLED_ITEM ( 'NONE', ( #7178 ), #54353 ) ; +#44919 = ORIENTED_EDGE ( 'NONE', *, *, #39025, .F. ) ; +#44920 = CARTESIAN_POINT ( 'NONE', ( -0.9897579360803360204, -1.341449062141889970, 0.8100000000000000533 ) ) ; +#44921 = ADVANCED_FACE ( 'NONE', ( #74141 ), #66466, .T. ) ; +#44922 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70988 ) ) ; +#44923 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47061, 'distance_accuracy_value', 'NONE'); +#44924 = SURFACE_STYLE_FILL_AREA ( #91917 ) ; +#44925 = AXIS2_PLACEMENT_3D ( 'NONE', #27665, #95537, #57300 ) ; +#44926 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44927 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, -3.099999999999969891, 0.000000000000000000 ) ) ; +#44928 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#44930 = LINE ( 'NONE', #76111, #98014 ) ; +#44929 = VECTOR ( 'NONE', #69355, 1000.000000000000000 ) ; +#44931 = SURFACE_SIDE_STYLE ('',( #83284 ) ) ; +#44932 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68562 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49805, #10367, #35989 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#44933 = LINE ( 'NONE', #82291, #62722 ) ; +#44934 = PRODUCT ( 'Submodel-QFN56_0P4_7_part_QFN56_0P4_7', 'Submodel-QFN56_0P4_7_part_QFN56_0P4_7', '', ( #100381 ) ) ; +#44935 = LINE ( 'NONE', #67923, #42076 ) ; +#44936 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31940 ), #43374 ) ; +#44937 = ORIENTED_EDGE ( 'NONE', *, *, #34679, .T. ) ; +#44938 = FILL_AREA_STYLE ('',( #85775 ) ) ; +#44939 = ORIENTED_EDGE ( 'NONE', *, *, #47404, .F. ) ; +#44940 = MANIFOLD_SOLID_BREP ( 'ÊäÈë66', #90836 ) ; +#44941 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691085, -0.01500000000000001506, -0.2458578643762690530 ) ) ; +#44942 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59858, 'distance_accuracy_value', 'NONE'); +#44943 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74109, 'distance_accuracy_value', 'NONE'); +#44944 = FILL_AREA_STYLE ('',( #60339 ) ) ; +#44945 = FACE_OUTER_BOUND ( 'NONE', #45002, .T. ) ; +#44946 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44947 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, -0.02000000000002725292 ) ) ; +#44948 = PLANE ( 'NONE', #16055 ) ; +#44949 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51588 ) ) ; +#44950 = PLANE ( 'NONE', #12239 ) ; +#44951 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#44952 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.300000000000000044, 0.000000000000000000 ) ) ; +#44953 = VECTOR ( 'NONE', #73135, 1000.000000000000000 ) ; +#44954 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#44955 = ORIENTED_EDGE ( 'NONE', *, *, #46871, .F. ) ; +#44957 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77568 ) ) ; +#44956 = FACE_OUTER_BOUND ( 'NONE', #10779, .T. ) ; +#44958 = ORIENTED_EDGE ( 'NONE', *, *, #28623, .F. ) ; +#44959 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#44960 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56484 ) ) ; +#44961 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.000000000000000000 ) ) ; +#44962 = VERTEX_POINT ( 'NONE', #21014 ) ; +#44963 = EDGE_CURVE ( 'NONE', #73926, #56505, #89944, .T. ) ; +#44964 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#44965 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#44966 = AXIS2_PLACEMENT_3D ( 'NONE', #4088, #89360, #26088 ) ; +#44967 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44968 = SURFACE_SIDE_STYLE ('',( #11754 ) ) ; +#44969 = PRESENTATION_STYLE_ASSIGNMENT (( #59868 ) ) ; +#44971 = ORIENTED_EDGE ( 'NONE', *, *, #152, .F. ) ; +#44970 = ORIENTED_EDGE ( 'NONE', *, *, #33135, .T. ) ; +#44972 = VECTOR ( 'NONE', #36650, 1000.000000000000000 ) ; +#44973 = SURFACE_STYLE_FILL_AREA ( #13799 ) ; +#44974 = VERTEX_POINT ( 'NONE', #45449 ) ; +#44975 = AXIS2_PLACEMENT_3D ( 'NONE', #88705, #66720, #35122 ) ; +#44976 = LINE ( 'NONE', #28197, #85137 ) ; +#44978 = LINE ( 'NONE', #5658, #813 ) ; +#44977 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#44979 = VERTEX_POINT ( 'NONE', #12774 ) ; +#44980 = EDGE_CURVE ( 'NONE', #48328, #9513, #43984, .T. ) ; +#44981 = ORIENTED_EDGE ( 'NONE', *, *, #38394, .F. ) ; +#44982 = SURFACE_SIDE_STYLE ('',( #36866 ) ) ; +#44983 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#44985 = FILL_AREA_STYLE_COLOUR ( '', #94000 ) ; +#44984 = SURFACE_SIDE_STYLE ('',( #75655 ) ) ; +#44986 = VERTEX_POINT ( 'NONE', #30149 ) ; +#44988 = VERTEX_POINT ( 'NONE', #90447 ) ; +#44987 = VECTOR ( 'NONE', #5200, 1000.000000000000000 ) ; +#44989 = EDGE_LOOP ( 'NONE', ( #31918, #27100, #12700 ) ) ; +#44990 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#44991 = AXIS2_PLACEMENT_3D ( 'NONE', #100310, #8417, #94254 ) ; +#44992 = VERTEX_POINT ( 'NONE', #53169 ) ; +#44993 = ADVANCED_FACE ( 'NONE', ( #75154 ), #51173, .T. ) ; +#44994 = SURFACE_STYLE_USAGE ( .BOTH. , #21056 ) ; +#44995 = AXIS2_PLACEMENT_3D ( 'NONE', #39282, #55163, #15787 ) ; +#44997 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#44996 = AXIS2_PLACEMENT_3D ( 'NONE', #74604, #82759, #81282 ) ; +#44998 = PLANE ( 'NONE', #50531 ) ; +#44999 = VERTEX_POINT ( 'NONE', #59860 ) ; +#45000 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45001 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45002 = EDGE_LOOP ( 'NONE', ( #15199, #81247, #35725, #13296 ) ) ; +#45003 = STYLED_ITEM ( 'NONE', ( #43010 ), #49707 ) ; +#45004 = VECTOR ( 'NONE', #86384, 1000.000000000000000 ) ; +#45005 = EDGE_CURVE ( 'NONE', #76877, #24035, #3396, .T. ) ; +#45006 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#45007 = AXIS2_PLACEMENT_3D ( 'NONE', #12432, #5309, #73803 ) ; +#45008 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45009 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #29797, #8257, #38482, #60975 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45010 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45011 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45012 = ORIENTED_EDGE ( 'NONE', *, *, #16525, .T. ) ; +#45013 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#45014 = FACE_OUTER_BOUND ( 'NONE', #93592, .T. ) ; +#45015 = EDGE_CURVE ( 'NONE', #12418, #5312, #99518, .T. ) ; +#45016 = FILL_AREA_STYLE_COLOUR ( '', #23727 ) ; +#45017 = CARTESIAN_POINT ( 'NONE', ( -1.203863976902495248, -1.140583172347456653, 0.8099999999998844791 ) ) ; +#45018 = VECTOR ( 'NONE', #32485, 1000.000000000000000 ) ; +#45020 = EDGE_CURVE ( 'NONE', #87086, #49180, #76134, .T. ) ; +#45019 = LINE ( 'NONE', #5197, #79886 ) ; +#45021 = LINE ( 'NONE', #52240, #93462 ) ; +#45022 = ORIENTED_EDGE ( 'NONE', *, *, #77674, .T. ) ; +#45023 = FILL_AREA_STYLE_COLOUR ( '', #71272 ) ; +#45024 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45025 = EDGE_CURVE ( 'NONE', #48032, #60367, #29660, .T. ) ; +#45026 = CARTESIAN_POINT ( 'NONE', ( 0.4626002664603570125, -1.036644144574919935, 0.8299999999999999600 ) ) ; +#45027 = CARTESIAN_POINT ( 'NONE', ( 0.6761799387799150018, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#45028 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822762999999999245, 0.8991599999999999593 ) ) ; +#45029 = PRODUCT_DEFINITION ( 'δ֪', '', #9441, #32045 ) ; +#45030 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67848 ) ) ; +#45031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99372 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91672, #51902, #83539 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45032 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18060, #43570, #10855, #26283 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45033 = ORIENTED_EDGE ( 'NONE', *, *, #28106, .T. ) ; +#45034 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89107 ), #72854 ) ; +#45035 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8991599999999999593 ) ) ; +#45036 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45037 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1050 ) ) ; +#45038 = ORIENTED_EDGE ( 'NONE', *, *, #60941, .F. ) ; +#45039 = EDGE_CURVE ( 'NONE', #51183, #63990, #30647, .T. ) ; +#45040 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45041 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#45042 = VECTOR ( 'NONE', #46626, 1000.000000000000000 ) ; +#45043 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#45044 = SURFACE_SIDE_STYLE ('',( #29262 ) ) ; +#45045 = EDGE_LOOP ( 'NONE', ( #2595, #85902, #9750, #90232 ) ) ; +#45046 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#45047 = EDGE_CURVE ( 'NONE', #29895, #61356, #81595, .T. ) ; +#45048 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45049 = PRESENTATION_STYLE_ASSIGNMENT (( #21594 ) ) ; +#45050 = SURFACE_STYLE_FILL_AREA ( #36927 ) ; +#45051 = LINE ( 'NONE', #23126, #11050 ) ; +#45052 = FILL_AREA_STYLE ('',( #6214 ) ) ; +#45053 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45054 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45055 = FACE_OUTER_BOUND ( 'NONE', #66728, .T. ) ; +#45056 = FILL_AREA_STYLE ('',( #92040 ) ) ; +#45057 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46668, 'distance_accuracy_value', 'NONE'); +#45058 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.4999999999999996669, 0.1829999999999790405 ) ) ; +#45059 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#45060 = ORIENTED_EDGE ( 'NONE', *, *, #79494, .F. ) ; +#45061 = SURFACE_STYLE_FILL_AREA ( #58958 ) ; +#45062 = EDGE_LOOP ( 'NONE', ( #98841, #53812, #90328, #58959 ) ) ; +#45063 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37160, 'distance_accuracy_value', 'NONE'); +#45065 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89599, 'distance_accuracy_value', 'NONE'); +#45066 = CARTESIAN_POINT ( 'NONE', ( 1.059879982250959918, -1.052467830684129968, 0.8299999999999999600 ) ) ; +#45067 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45068 = CARTESIAN_POINT ( 'NONE', ( -0.9327878365278901018, -1.419416888468929994, 0.8299999999999981837 ) ) ; +#45069 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#45070 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45071 = SURFACE_SIDE_STYLE ('',( #14915 ) ) ; +#45072 = LINE ( 'NONE', #100117, #90074 ) ; +#45073 = PLANE ( 'NONE', #4387 ) ; +#45074 = SURFACE_STYLE_USAGE ( .BOTH. , #75744 ) ; +#45075 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45076 = ORIENTED_EDGE ( 'NONE', *, *, #11249, .T. ) ; +#45077 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5913 ), #82588 ) ; +#45078 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15607, 'distance_accuracy_value', 'NONE'); +#45079 = AXIS2_PLACEMENT_3D ( 'NONE', #21068, #35903, #36393 ) ; +#45080 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, -0.01500000000000001332, 0.2399999999999999356 ) ) ; +#45081 = SURFACE_SIDE_STYLE ('',( #91569 ) ) ; +#45082 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45083 = VERTEX_POINT ( 'NONE', #48018 ) ; +#45084 = FACE_OUTER_BOUND ( 'NONE', #9230, .T. ) ; +#45085 = EDGE_CURVE ( 'NONE', #28438, #28706, #15829, .T. ) ; +#45086 = FACE_OUTER_BOUND ( 'NONE', #56886, .T. ) ; +#45087 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45088 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72830 ), #12457 ) ; +#45089 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45090 = SURFACE_STYLE_FILL_AREA ( #52795 ) ; +#45091 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45092 = AXIS2_PLACEMENT_3D ( 'NONE', #4379, #42211, #51875 ) ; +#45093 = VERTEX_POINT ( 'NONE', #78638 ) ; +#45094 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45095 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81656, 'distance_accuracy_value', 'NONE'); +#45096 = AXIS2_PLACEMENT_3D ( 'NONE', #94286, #69803, #14647 ) ; +#45097 = VECTOR ( 'NONE', #53784, 1000.000000000000000 ) ; +#45098 = CLOSED_SHELL ( 'NONE', ( #11250, #16640, #72247, #22470, #44590, #36302 ) ) ; +#45099 = ORIENTED_EDGE ( 'NONE', *, *, #73830, .F. ) ; +#45100 = VECTOR ( 'NONE', #78981, 1000.000000000000000 ) ; +#45101 = ADVANCED_FACE ( 'NONE', ( #84786 ), #31181, .T. ) ; +#45102 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#45103 = PRESENTATION_STYLE_ASSIGNMENT (( #13937 ) ) ; +#45104 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#45105 = ORIENTED_EDGE ( 'NONE', *, *, #47150, .T. ) ; +#45106 = EDGE_CURVE ( 'NONE', #77581, #88427, #77131, .T. ) ; +#45107 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97301 ) ) ; +#45108 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11740, #35365, #58353, #4668 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45109 = MANIFOLD_SOLID_BREP ( 'ÊäÈë150', #76241 ) ; +#45110 = VERTEX_POINT ( 'NONE', #8604 ) ; +#45112 = VERTEX_POINT ( 'NONE', #94450 ) ; +#45111 = CARTESIAN_POINT ( 'NONE', ( 0.3666666666666633101, -3.500000000000000000, 0.000000000000000000 ) ) ; +#45113 = FILL_AREA_STYLE_COLOUR ( '', #65418 ) ; +#45114 = SURFACE_SIDE_STYLE ('',( #53818 ) ) ; +#45115 = VERTEX_POINT ( 'NONE', #24574 ) ; +#45116 = DIRECTION ( 'NONE', ( 0.7071075504167448900, 0.7071060119555133694, 0.000000000000000000 ) ) ; +#45117 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45118 = LINE ( 'NONE', #6757, #42648 ) ; +#45119 = ORIENTED_EDGE ( 'NONE', *, *, #80401, .T. ) ; +#45120 = EDGE_CURVE ( 'NONE', #8779, #85090, #39852, .T. ) ; +#45121 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45122 = SURFACE_STYLE_FILL_AREA ( #83472 ) ; +#45123 = ORIENTED_EDGE ( 'NONE', *, *, #42991, .T. ) ; +#45124 = VECTOR ( 'NONE', #93858, 1000.000000000000000 ) ; +#45126 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45125 = FILL_AREA_STYLE_COLOUR ( '', #89400 ) ; +#45127 = EDGE_LOOP ( 'NONE', ( #99667, #44860, #1672, #5128 ) ) ; +#45128 = ADVANCED_FACE ( 'NONE', ( #63855 ), #22504, .F. ) ; +#45130 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, 0.000000000000000000 ) ) ; +#45129 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8648700000000000276 ) ) ; +#45131 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68427 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79634, #46934, #89482 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45132 = SURFACE_SIDE_STYLE ('',( #15496 ) ) ; +#45134 = EDGE_CURVE ( 'NONE', #85310, #10872, #58600, .T. ) ; +#45133 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#45135 = LINE ( 'NONE', #23208, #97273 ) ; +#45136 = VECTOR ( 'NONE', #32177, 1000.000000000000000 ) ; +#45137 = STYLED_ITEM ( 'NONE', ( #875 ), #90904 ) ; +#45138 = ORIENTED_EDGE ( 'NONE', *, *, #97957, .F. ) ; +#45139 = ORIENTED_EDGE ( 'NONE', *, *, #87644, .T. ) ; +#45140 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45141 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#45142 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46755 ), #59878 ) ; +#45143 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#45144 = STYLED_ITEM ( 'NONE', ( #100551 ), #79026 ) ; +#45145 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#45146 = FACE_OUTER_BOUND ( 'NONE', #22385, .T. ) ; +#45147 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45148 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#45149 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45150 = AXIS2_PLACEMENT_3D ( 'NONE', #29440, #98304, #28442 ) ; +#45151 = VERTEX_POINT ( 'NONE', #20245 ) ; +#45152 = FACE_OUTER_BOUND ( 'NONE', #67248, .T. ) ; +#45153 = EDGE_CURVE ( 'NONE', #1586, #63240, #95448, .T. ) ; +#45154 = VECTOR ( 'NONE', #49558, 1000.000000000000000 ) ; +#45155 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74517 ), #38627 ) ; +#45157 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45156 = SURFACE_STYLE_USAGE ( .BOTH. , #38044 ) ; +#45158 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8648700000000000276 ) ) ; +#45159 = LINE ( 'NONE', #76324, #43027 ) ; +#45160 = STYLED_ITEM ( 'NONE', ( #97781 ), #40948 ) ; +#45161 = VECTOR ( 'NONE', #75158, 1000.000000000000114 ) ; +#45162 = LINE ( 'NONE', #68656, #14173 ) ; +#45163 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74594 ) ) ; +#45164 = PRESENTATION_STYLE_ASSIGNMENT (( #84009 ) ) ; +#45165 = CLOSED_SHELL ( 'NONE', ( #25754, #54353, #91308, #58855, #54433, #1419 ) ) ; +#45166 = LINE ( 'NONE', #38049, #15129 ) ; +#45167 = ORIENTED_EDGE ( 'NONE', *, *, #88341, .F. ) ; +#45168 = EDGE_CURVE ( 'NONE', #77051, #96015, #27951, .T. ) ; +#45169 = PLANE ( 'NONE', #22826 ) ; +#45170 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45171 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45173 = LINE ( 'NONE', #85000, #33210 ) ; +#45174 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, -0.1500000000000000222 ) ) ; +#45175 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#45176 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051949811, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#45177 = LINE ( 'NONE', #76341, #47914 ) ; +#45178 = LINE ( 'NONE', #37074, #84247 ) ; +#45179 = VECTOR ( 'NONE', #565, 1000.000000000000000 ) ; +#45180 = FILL_AREA_STYLE ('',( #14020 ) ) ; +#45181 = PRESENTATION_STYLE_ASSIGNMENT (( #99253 ) ) ; +#45182 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45183 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#45184 = EDGE_CURVE ( 'NONE', #97367, #41960, #40876, .T. ) ; +#45185 = SURFACE_SIDE_STYLE ('',( #76867 ) ) ; +#45186 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45187 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47240, 'distance_accuracy_value', 'NONE'); +#45188 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45191 = ADVANCED_FACE ( 'NONE', ( #9625 ), #98295, .F. ) ; +#45190 = SURFACE_STYLE_FILL_AREA ( #14032 ) ; +#45192 = LINE ( 'NONE', #43708, #11680 ) ; +#45193 = EDGE_LOOP ( 'NONE', ( #35667, #6724, #34352, #27708 ) ) ; +#45194 = FILL_AREA_STYLE_COLOUR ( '', #43791 ) ; +#45195 = LINE ( 'NONE', #37092, #1376 ) ; +#45196 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97570, 'distance_accuracy_value', 'NONE'); +#45197 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#45198 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45199 = CARTESIAN_POINT ( 'NONE', ( -0.07193707439540279747, -0.9683984092875530525, 0.8300000000000002931 ) ) ; +#45200 = ADVANCED_FACE ( 'NONE', ( #59619 ), #25068, .F. ) ; +#45201 = EDGE_CURVE ( 'NONE', #77835, #24092, #14051, .T. ) ; +#45202 = SURFACE_STYLE_USAGE ( .BOTH. , #68195 ) ; +#45203 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45204 = STYLED_ITEM ( 'NONE', ( #8945 ), #30756 ) ; +#45205 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#45206 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45207 = ORIENTED_EDGE ( 'NONE', *, *, #30872, .F. ) ; +#45208 = EDGE_CURVE ( 'NONE', #31005, #81966, #68703, .T. ) ; +#45209 = EDGE_CURVE ( 'NONE', #31030, #43775, #37107, .T. ) ; +#45210 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49113, 'distance_accuracy_value', 'NONE'); +#45211 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45212 = CARTESIAN_POINT ( 'NONE', ( -0.08876197264234840512, -1.443664018207750033, 0.8300000000000006262 ) ) ; +#45213 = SURFACE_STYLE_USAGE ( .BOTH. , #14053 ) ; +#45214 = ORIENTED_EDGE ( 'NONE', *, *, #95907, .F. ) ; +#45215 = ORIENTED_EDGE ( 'NONE', *, *, #36684, .T. ) ; +#45216 = EDGE_CURVE ( 'NONE', #61035, #986, #97258, .T. ) ; +#45217 = PRESENTATION_STYLE_ASSIGNMENT (( #75891 ) ) ; +#45218 = ORIENTED_EDGE ( 'NONE', *, *, #91235, .T. ) ; +#45219 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77827 ), #71351 ) ; +#45220 = CARTESIAN_POINT ( 'NONE', ( 0.06855147566562069805, -1.423344911062679907, 0.8299999999999999600 ) ) ; +#45221 = CARTESIAN_POINT ( 'NONE', ( 0.5194035290631999757, -1.172439657072400054, 0.8299999999999999600 ) ) ; +#45222 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#45223 = SURFACE_SIDE_STYLE ('',( #99763 ) ) ; +#45224 = EDGE_CURVE ( 'NONE', #43745, #30000, #99750, .T. ) ; +#45225 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89300 ), #68048 ) ; +#45226 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45227 = VERTEX_POINT ( 'NONE', #61094 ) ; +#45228 = VECTOR ( 'NONE', #54397, 1000.000000000000000 ) ; +#45229 = VECTOR ( 'NONE', #25635, 1000.000000000000000 ) ; +#45230 = ORIENTED_EDGE ( 'NONE', *, *, #88408, .T. ) ; +#45231 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#45232 = SURFACE_STYLE_FILL_AREA ( #84563 ) ; +#45233 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45234 = VECTOR ( 'NONE', #2071, 1000.000000000000000 ) ; +#45236 = CARTESIAN_POINT ( 'NONE', ( 1.391117489400210072, -0.9747981717974689708, 0.8299999999999999600 ) ) ; +#45235 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45237 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45238 = CLOSED_SHELL ( 'NONE', ( #91397, #6287, #37523, #52644, #88100, #31200 ) ) ; +#45239 = SURFACE_SIDE_STYLE ('',( #77415 ) ) ; +#45240 = ORIENTED_EDGE ( 'NONE', *, *, #36339, .F. ) ; +#45241 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77861 ) ) ; +#45242 = EDGE_LOOP ( 'NONE', ( #62358, #54305, #4749, #93583 ) ) ; +#45243 = ORIENTED_EDGE ( 'NONE', *, *, #3880, .T. ) ; +#45244 = CARTESIAN_POINT ( 'NONE', ( 1.316661513406260031, -1.260670644472420054, 0.8100000000000000533 ) ) ; +#45245 = STYLED_ITEM ( 'NONE', ( #80112 ), #14820 ) ; +#45247 = SURFACE_STYLE_FILL_AREA ( #84582 ) ; +#45246 = SURFACE_SIDE_STYLE ('',( #68242 ) ) ; +#45248 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1268 ), #1344 ) ; +#45250 = EDGE_CURVE ( 'NONE', #19914, #17757, #15580, .T. ) ; +#45249 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45252 = VERTEX_POINT ( 'NONE', #22266 ) ; +#45251 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45253 = AXIS2_PLACEMENT_3D ( 'NONE', #97431, #12628, #21861 ) ; +#45254 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#45255 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45256 = ORIENTED_EDGE ( 'NONE', *, *, #63847, .T. ) ; +#45258 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45257 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#45259 = ORIENTED_EDGE ( 'NONE', *, *, #24044, .T. ) ; +#45260 = EDGE_CURVE ( 'NONE', #81900, #51946, #26632, .T. ) ; +#45261 = ORIENTED_EDGE ( 'NONE', *, *, #226, .T. ) ; +#45262 = SURFACE_STYLE_FILL_AREA ( #42432 ) ; +#45264 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45263 = CARTESIAN_POINT ( 'NONE', ( 1.134147553444200041, -1.508462442331270026, 0.8100000000000000533 ) ) ; +#45265 = FILL_AREA_STYLE ('',( #90767 ) ) ; +#45266 = SURFACE_STYLE_USAGE ( .BOTH. , #91260 ) ; +#45267 = CARTESIAN_POINT ( 'NONE', ( 3.383841750250087266, 4.963071249749912539, 0.8991599999999999593 ) ) ; +#45268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45269 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#45270 = VECTOR ( 'NONE', #98121, 1000.000000000000000 ) ; +#45271 = FILL_AREA_STYLE_COLOUR ( '', #13516 ) ; +#45272 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000020206, 0.1829999999999619986 ) ) ; +#45273 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -1.100000000000000089 ) ) ; +#45274 = VECTOR ( 'NONE', #38047, 1000.000000000000000 ) ; +#45275 = VERTEX_POINT ( 'NONE', #14559 ) ; +#45276 = VERTEX_POINT ( 'NONE', #53920 ) ; +#45277 = EDGE_CURVE ( 'NONE', #26719, #81738, #21878, .T. ) ; +#45278 = LINE ( 'NONE', #92265, #49808 ) ; +#45279 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#45280 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11508 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5384, #36594, #4895 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45281 = AXIS2_PLACEMENT_3D ( 'NONE', #79774, #78731, #54794 ) ; +#45282 = FACE_OUTER_BOUND ( 'NONE', #95114, .T. ) ; +#45283 = LINE ( 'NONE', #6451, #55032 ) ; +#45284 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#45285 = SURFACE_STYLE_FILL_AREA ( #98363 ) ; +#45287 = ORIENTED_EDGE ( 'NONE', *, *, #59147, .F. ) ; +#45286 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74712 ), #37186 ) ; +#45288 = LINE ( 'NONE', #76459, #98216 ) ; +#45289 = SURFACE_STYLE_FILL_AREA ( #14135 ) ; +#45290 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45291 = SURFACE_STYLE_FILL_AREA ( #99835 ) ; +#45292 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30774 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97637, #35919, #82863 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45293 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#45294 = CARTESIAN_POINT ( 'NONE', ( 1.867699582579569917, -1.228633653069070020, 0.8299999999999999600 ) ) ; +#45295 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#45296 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32069 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26350, #3847, #81979 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45297 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#45298 = CARTESIAN_POINT ( 'NONE', ( 0.4645119866146585341, 0.3274465759269651888, 0.8100000000000000533 ) ) ; +#45300 = VECTOR ( 'NONE', #66938, 1000.000000000000000 ) ; +#45299 = FILL_AREA_STYLE ('',( #24404 ) ) ; +#45301 = LINE ( 'NONE', #59713, #74828 ) ; +#45302 = AXIS2_PLACEMENT_3D ( 'NONE', #49371, #9967, #16668 ) ; +#45303 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45304 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45305 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46980 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44442, #55569, #8468 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45306 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#45307 = STYLED_ITEM ( 'NONE', ( #47770 ), #23492 ) ; +#45308 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19237, 'distance_accuracy_value', 'NONE'); +#45309 = CLOSED_SHELL ( 'NONE', ( #40885, #33085, #68385, #50579, #89002, #52181 ) ) ; +#45310 = PRESENTATION_STYLE_ASSIGNMENT (( #44811 ) ) ; +#45311 = SURFACE_SIDE_STYLE ('',( #35710 ) ) ; +#45312 = CARTESIAN_POINT ( 'NONE', ( -1.200869043929681190, -1.440493760292191894, 0.8099999999996634337 ) ) ; +#45313 = ORIENTED_EDGE ( 'NONE', *, *, #91192, .F. ) ; +#45314 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.000000000000000000, -11.41999999999999993 ) ) ; +#45315 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45316 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45317 = CARTESIAN_POINT ( 'NONE', ( 1.617712736099780280, -1.425091422160009946, 0.8299999999999977396 ) ) ; +#45318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62551, 'distance_accuracy_value', 'NONE'); +#45319 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66416, #59306, #81271 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45320 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.000000000000000000 ) ) ; +#45321 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64973 ) ) ; +#45322 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#45323 = STYLED_ITEM ( 'NONE', ( #23848 ), #49993 ) ; +#45324 = ORIENTED_EDGE ( 'NONE', *, *, #65915, .T. ) ; +#45325 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45326 = FACE_OUTER_BOUND ( 'NONE', #9165, .T. ) ; +#45327 = STYLED_ITEM ( 'NONE', ( #32803 ), #43847 ) ; +#45328 = EDGE_CURVE ( 'NONE', #258, #81145, #70339, .T. ) ; +#45329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79393, 'distance_accuracy_value', 'NONE'); +#45330 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45331 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45186, 'distance_accuracy_value', 'NONE'); +#45332 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45333 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64918 ), #7738 ) ; +#45334 = EDGE_LOOP ( 'NONE', ( #80282, #19663, #40152, #99732 ) ) ; +#45335 = EDGE_LOOP ( 'NONE', ( #66376, #93306, #29197, #21578 ) ) ; +#45336 = FILL_AREA_STYLE_COLOUR ( '', #77189 ) ; +#45337 = SURFACE_STYLE_USAGE ( .BOTH. , #66844 ) ; +#45338 = ORIENTED_EDGE ( 'NONE', *, *, #20050, .F. ) ; +#45339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45340 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45341 = EDGE_CURVE ( 'NONE', #44986, #64247, #72256, .T. ) ; +#45342 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45343 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #1185 ) ; +#45344 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8648700000000000276 ) ) ; +#45345 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45347 = ORIENTED_EDGE ( 'NONE', *, *, #99339, .T. ) ; +#45346 = VERTEX_POINT ( 'NONE', #24318 ) ; +#45348 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45349 = EDGE_LOOP ( 'NONE', ( #59855, #47624, #25746, #33126, #20241, #12154 ) ) ; +#45350 = AXIS2_PLACEMENT_3D ( 'NONE', #86282, #71475, #78616 ) ; +#45351 = SURFACE_SIDE_STYLE ('',( #14194 ) ) ; +#45352 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#45353 = ORIENTED_EDGE ( 'NONE', *, *, #87286, .T. ) ; +#45354 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94272 ) ) ; +#45355 = ORIENTED_EDGE ( 'NONE', *, *, #8795, .F. ) ; +#45356 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#45357 = SURFACE_STYLE_USAGE ( .BOTH. , #14200 ) ; +#45358 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53285 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73080, #25621, #26634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45360 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45359 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -4.701977403289150032E-32 ) ) ; +#45361 = FACE_OUTER_BOUND ( 'NONE', #19579, .T. ) ; +#45362 = VERTEX_POINT ( 'NONE', #16586 ) ; +#45363 = LINE ( 'NONE', #53078, #4624 ) ; +#45364 = ORIENTED_EDGE ( 'NONE', *, *, #15675, .T. ) ; +#45365 = ORIENTED_EDGE ( 'NONE', *, *, #51048, .F. ) ; +#45366 = VECTOR ( 'NONE', #16251, 1000.000000000000000 ) ; +#45367 = SURFACE_SIDE_STYLE ('',( #67859 ) ) ; +#45368 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87762 ) ) ; +#45369 = SURFACE_STYLE_USAGE ( .BOTH. , #7515 ) ; +#45372 = EDGE_LOOP ( 'NONE', ( #65239, #75754, #45851, #92705 ) ) ; +#45371 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70772, 'distance_accuracy_value', 'NONE'); +#45370 = CARTESIAN_POINT ( 'NONE', ( -1.076179938779914913, -3.099999999999990319, 0.000000000000000000 ) ) ; +#45374 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61765 ), #92673 ) ; +#45373 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45375 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#45376 = FILL_AREA_STYLE ('',( #7521 ) ) ; +#45377 = EDGE_LOOP ( 'NONE', ( #88255, #75165, #95746, #80611 ) ) ; +#45378 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#45379 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16089 ), #47082 ) ; +#45380 = FACE_OUTER_BOUND ( 'NONE', #64179, .T. ) ; +#45381 = EDGE_LOOP ( 'NONE', ( #62826, #27221, #72211, #78548 ) ) ; +#45382 = EDGE_CURVE ( 'NONE', #93554, #85273, #79940, .T. ) ; +#45383 = VERTEX_POINT ( 'NONE', #8870 ) ; +#45384 = PLANE ( 'NONE', #10595 ) ; +#45385 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45386 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#45387 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99126 ), #84557 ) ; +#45388 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8648700000000000276 ) ) ; +#45389 = FILL_AREA_STYLE ('',( #60777 ) ) ; +#45390 = VECTOR ( 'NONE', #51356, 1000.000000000000000 ) ; +#45391 = ORIENTED_EDGE ( 'NONE', *, *, #9861, .T. ) ; +#45392 = CARTESIAN_POINT ( 'NONE', ( 0.4526194431797169737, -1.137806428429579908, 0.8299999999999999600 ) ) ; +#45393 = VERTEX_POINT ( 'NONE', #47766 ) ; +#45394 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#45395 = STYLED_ITEM ( 'NONE', ( #7587 ), #44016 ) ; +#45396 = SURFACE_STYLE_FILL_AREA ( #69385 ) ; +#45397 = LINE ( 'NONE', #63314, #56245 ) ; +#45398 = FILL_AREA_STYLE_COLOUR ( '', #14328 ) ; +#45400 = PLANE ( 'NONE', #66289 ) ; +#45399 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1458578643762690197 ) ) ; +#45401 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.500000000000000222, 0.1829999999999870064 ) ) ; +#45402 = SURFACE_SIDE_STYLE ('',( #75105 ) ) ; +#45403 = FILL_AREA_STYLE_COLOUR ( '', #69431 ) ; +#45404 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45406 = EDGE_CURVE ( 'NONE', #49704, #1370, #88090, .T. ) ; +#45405 = FACE_OUTER_BOUND ( 'NONE', #42383, .T. ) ; +#45407 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#45408 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45409 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#45410 = VECTOR ( 'NONE', #57569, 1000.000000000000000 ) ; +#45411 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51962 ) ) ; +#45412 = LINE ( 'NONE', #82389, #3962 ) ; +#45413 = AXIS2_PLACEMENT_3D ( 'NONE', #52531, #59228, #52045 ) ; +#45414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84761 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #888, #40722, #54533 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45415 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#45416 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45417 = VECTOR ( 'NONE', #95065, 1000.000000000000000 ) ; +#45418 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88528, 'distance_accuracy_value', 'NONE'); +#45419 = ORIENTED_EDGE ( 'NONE', *, *, #47662, .F. ) ; +#45420 = CARTESIAN_POINT ( 'NONE', ( -0.9897579360803360204, -1.341449062141889970, 0.8299999999999999600 ) ) ; +#45421 = EDGE_CURVE ( 'NONE', #49062, #14566, #78910, .T. ) ; +#45422 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45423 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.899999999999993472, 0.1829999999999919746 ) ) ; +#45424 = PRESENTATION_STYLE_ASSIGNMENT (( #19971 ) ) ; +#45425 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45426 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45427 = STYLED_ITEM ( 'NONE', ( #4962 ), #17825 ) ; +#45428 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#45429 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22593 ), #92668 ) ; +#45430 = ORIENTED_EDGE ( 'NONE', *, *, #71876, .F. ) ; +#45431 = PLANE ( 'NONE', #88950 ) ; +#45432 = ORIENTED_EDGE ( 'NONE', *, *, #8347, .F. ) ; +#45434 = MANIFOLD_SOLID_BREP ( 'ÊäÈë29', #54999 ) ; +#45433 = AXIS2_PLACEMENT_3D ( 'NONE', #8301, #87508, #31368 ) ; +#45435 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45436 = SURFACE_STYLE_FILL_AREA ( #14283 ) ; +#45438 = VECTOR ( 'NONE', #17590, 1000.000000000000000 ) ; +#45437 = CARTESIAN_POINT ( 'NONE', ( -0.1830714119375710103, -0.9850088450568520448, 0.8299999999999999600 ) ) ; +#45439 = FACE_OUTER_BOUND ( 'NONE', #8732, .T. ) ; +#45440 = EDGE_CURVE ( 'NONE', #54838, #90356, #9390, .T. ) ; +#45441 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#45442 = FILL_AREA_STYLE_COLOUR ( '', #50139 ) ; +#45443 = PLANE ( 'NONE', #92916 ) ; +#45444 = FACE_OUTER_BOUND ( 'NONE', #92343, .T. ) ; +#45445 = ORIENTED_EDGE ( 'NONE', *, *, #36348, .F. ) ; +#45446 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62055, #14003, #83511, #52378 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45447 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45448 = EDGE_LOOP ( 'NONE', ( #14296, #59801, #39009, #2962 ) ) ; +#45449 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980549, 0.000000000000000000 ) ) ; +#45450 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#45451 = ORIENTED_EDGE ( 'NONE', *, *, #36936, .T. ) ; +#45452 = AXIS2_PLACEMENT_3D ( 'NONE', #47073, #8188, #78239 ) ; +#45453 = LINE ( 'NONE', #29183, #32167 ) ; +#45454 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23262, #77352, #763 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45455 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45456 = EDGE_CURVE ( 'NONE', #1063, #83292, #24826, .T. ) ; +#45457 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#45458 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45459 = CARTESIAN_POINT ( 'NONE', ( 1.877211804471180079, -1.084027901463999966, 0.8299999999999999600 ) ) ; +#45461 = ORIENTED_EDGE ( 'NONE', *, *, #70755, .F. ) ; +#45460 = EDGE_LOOP ( 'NONE', ( #38389, #50982, #26651, #91381, #79824, #35943 ) ) ; +#45462 = ORIENTED_EDGE ( 'NONE', *, *, #72811, .F. ) ; +#45463 = LINE ( 'NONE', #5159, #18288 ) ; +#45465 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558440262, -1.079220779220779969, 0.8100000000000000533 ) ) ; +#45464 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#45466 = ORIENTED_EDGE ( 'NONE', *, *, #21177, .T. ) ; +#45467 = ORIENTED_EDGE ( 'NONE', *, *, #68236, .F. ) ; +#45468 = SURFACE_STYLE_USAGE ( .BOTH. , #62877 ) ; +#45469 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45470 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45471 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45472 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45473 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51417 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46761, #84574, #85077 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45474 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45475 = CARTESIAN_POINT ( 'NONE', ( 2.300000000000000266, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#45476 = ORIENTED_EDGE ( 'NONE', *, *, #69299, .T. ) ; +#45477 = VERTEX_POINT ( 'NONE', #55957 ) ; +#45478 = ORIENTED_EDGE ( 'NONE', *, *, #77382, .T. ) ; +#45479 = LINE ( 'NONE', #75661, #34596 ) ; +#45480 = VECTOR ( 'NONE', #26727, 1000.000000000000000 ) ; +#45481 = STYLED_ITEM ( 'NONE', ( #90684 ), #31909 ) ; +#45482 = EDGE_CURVE ( 'NONE', #47424, #52771, #8364, .T. ) ; +#45483 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45485 = ORIENTED_EDGE ( 'NONE', *, *, #36277, .F. ) ; +#45484 = SURFACE_STYLE_FILL_AREA ( #16361 ) ; +#45486 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94418 ) ) ; +#45487 = SURFACE_SIDE_STYLE ('',( #42659 ) ) ; +#45488 = SURFACE_STYLE_USAGE ( .BOTH. , #70517 ) ; +#45489 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 2.300000000000000266, 0.000000000000000000 ) ) ; +#45490 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#45491 = ORIENTED_EDGE ( 'NONE', *, *, #41295, .T. ) ; +#45492 = CYLINDRICAL_SURFACE ( 'NONE', #49346, 0.01000000000000002623 ) ; +#45493 = ORIENTED_EDGE ( 'NONE', *, *, #32950, .F. ) ; +#45494 = ADVANCED_FACE ( 'NONE', ( #62614 ), #54948, .T. ) ; +#45495 = VECTOR ( 'NONE', #64115, 1000.000000000000000 ) ; +#45496 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45497 = SURFACE_STYLE_FILL_AREA ( #84832 ) ; +#45499 = ORIENTED_EDGE ( 'NONE', *, *, #33743, .F. ) ; +#45498 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#45500 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000021, -0.2250000000000000333 ) ) ; +#45501 = LINE ( 'NONE', #578, #81320 ) ; +#45502 = CARTESIAN_POINT ( 'NONE', ( 1.673324881778589956, -1.507258815139120189, 0.8100000000000000533 ) ) ; +#45503 = CARTESIAN_POINT ( 'NONE', ( -1.072951258369055916, -1.171570345189036688, 0.8099999999998616085 ) ) ; +#45504 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#45505 = ORIENTED_EDGE ( 'NONE', *, *, #83352, .T. ) ; +#45506 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45509 = CARTESIAN_POINT ( 'NONE', ( 1.664835065683849979, -1.443372874996269983, 0.8299999999999999600 ) ) ; +#45508 = CARTESIAN_POINT ( 'NONE', ( 0.4587323827270540222, -1.026347246440100003, 0.8299999999999999600 ) ) ; +#45510 = LINE ( 'NONE', #67033, #50256 ) ; +#45511 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.009999999999999998473, 1.250000000000000000 ) ) ; +#45512 = SURFACE_STYLE_USAGE ( .BOTH. , #4739 ) ; +#45513 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45514 = EDGE_LOOP ( 'NONE', ( #75894, #98199, #34317, #70603 ) ) ; +#45515 = EDGE_CURVE ( 'NONE', #100148, #75434, #98472, .T. ) ; +#45516 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45517 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45518 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45519 = VERTEX_POINT ( 'NONE', #98175 ) ; +#45521 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45520 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45522 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#45523 = STYLED_ITEM ( 'NONE', ( #60590 ), #44377 ) ; +#45524 = VERTEX_POINT ( 'NONE', #74272 ) ; +#45525 = FILL_AREA_STYLE ('',( #37923 ) ) ; +#45526 = ADVANCED_FACE ( 'NONE', ( #96218 ), #89593, .T. ) ; +#45527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45528 = CARTESIAN_POINT ( 'NONE', ( -0.05867698335161790346, -1.150470459123589917, 0.8300000000000005151 ) ) ; +#45529 = FACE_OUTER_BOUND ( 'NONE', #40232, .T. ) ; +#45530 = PLANE ( 'NONE', #86840 ) ; +#45531 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45533 = LINE ( 'NONE', #52270, #79188 ) ; +#45534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97727 ), #76554 ) ; +#45535 = LINE ( 'NONE', #31775, #76860 ) ; +#45536 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.000000000000000000 ) ) ; +#45537 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45538 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45539 = AXIS2_PLACEMENT_3D ( 'NONE', #39766, #1976, #79588 ) ; +#45540 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#45541 = SURFACE_SIDE_STYLE ('',( #52278 ) ) ; +#45542 = ORIENTED_EDGE ( 'NONE', *, *, #97969, .T. ) ; +#45543 = ORIENTED_EDGE ( 'NONE', *, *, #39331, .F. ) ; +#45544 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#45545 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68397 ), #40746 ) ; +#45546 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45547 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45548 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#45549 = FILL_AREA_STYLE_COLOUR ( '', #6869 ) ; +#45550 = EDGE_CURVE ( 'NONE', #88330, #62932, #73772, .T. ) ; +#45551 = STYLED_ITEM ( 'NONE', ( #47050 ), #94179 ) ; +#45552 = CARTESIAN_POINT ( 'NONE', ( 1.767907037466160070, -0.9096959278232360502, 0.8100000000000000533 ) ) ; +#45553 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45554 = FILL_AREA_STYLE ('',( #37468 ) ) ; +#45555 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19519 ), #11267 ) ; +#45556 = ORIENTED_EDGE ( 'NONE', *, *, #93036, .T. ) ; +#45557 = PLANE ( 'NONE', #83522 ) ; +#45558 = FILL_AREA_STYLE_COLOUR ( '', #43312 ) ; +#45559 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63572 ), #39122 ) ; +#45560 = EDGE_CURVE ( 'NONE', #76182, #23174, #81465, .T. ) ; +#45561 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#45562 = STYLED_ITEM ( 'NONE', ( #23605 ), #80521 ) ; +#45563 = ORIENTED_EDGE ( 'NONE', *, *, #34656, .T. ) ; +#45564 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#45565 = FILL_AREA_STYLE_COLOUR ( '', #76100 ) ; +#45566 = PLANE ( 'NONE', #72348 ) ; +#45567 = EDGE_CURVE ( 'NONE', #47444, #87344, #35496, .T. ) ; +#45568 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45569 = EDGE_CURVE ( 'NONE', #17149, #63404, #34996, .T. ) ; +#45570 = SURFACE_STYLE_USAGE ( .BOTH. , #14432 ) ; +#45571 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.004999999999999986226, -0.1500000000000000222 ) ) ; +#45572 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #18831, #99561 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #32083 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#45573 = ORIENTED_EDGE ( 'NONE', *, *, #9880, .F. ) ; +#45574 = VECTOR ( 'NONE', #89268, 1000.000000000000000 ) ; +#45575 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45576 = SURFACE_STYLE_USAGE ( .BOTH. , #67098 ) ; +#45577 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45578 = ORIENTED_EDGE ( 'NONE', *, *, #4672, .F. ) ; +#45579 = STYLED_ITEM ( 'NONE', ( #71012 ), #10496 ) ; +#45580 = SURFACE_STYLE_FILL_AREA ( #59507 ) ; +#45581 = FILL_AREA_STYLE ('',( #100144 ) ) ; +#45582 = FACE_OUTER_BOUND ( 'NONE', #79852, .T. ) ; +#45583 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45584 = PRESENTATION_STYLE_ASSIGNMENT (( #76268 ) ) ; +#45585 = ORIENTED_EDGE ( 'NONE', *, *, #79859, .T. ) ; +#45586 = ORIENTED_EDGE ( 'NONE', *, *, #99127, .T. ) ; +#45587 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70799, 'distance_accuracy_value', 'NONE'); +#45588 = EDGE_CURVE ( 'NONE', #59128, #51695, #50790, .T. ) ; +#45589 = MANIFOLD_SOLID_BREP ( 'ÊäÈë97', #46935 ) ; +#45590 = ORIENTED_EDGE ( 'NONE', *, *, #48355, .T. ) ; +#45592 = ORIENTED_EDGE ( 'NONE', *, *, #36279, .T. ) ; +#45591 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45593 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40527, 'distance_accuracy_value', 'NONE'); +#45594 = PLANE ( 'NONE', #39402 ) ; +#45596 = FILL_AREA_STYLE ('',( #30822 ) ) ; +#45595 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000030032, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#45597 = FILL_AREA_STYLE ('',( #68103 ) ) ; +#45598 = FACE_OUTER_BOUND ( 'NONE', #10599, .T. ) ; +#45599 = EDGE_LOOP ( 'NONE', ( #1594, #6888, #48299, #75050 ) ) ; +#45600 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45601 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45602 = PLANE ( 'NONE', #29583 ) ; +#45603 = EDGE_LOOP ( 'NONE', ( #47072, #34785, #27553 ) ) ; +#45604 = ADVANCED_FACE ( 'NONE', ( #22658 ), #66600, .T. ) ; +#45605 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.8500000000100800257, 0.6499230723517829267 ) ) ; +#45606 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, 0.000000000000000000 ) ) ; +#45607 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8100000000000601164 ) ) ; +#45608 = SURFACE_SIDE_STYLE ('',( #30310 ) ) ; +#45609 = ORIENTED_EDGE ( 'NONE', *, *, #79637, .F. ) ; +#45610 = EDGE_CURVE ( 'NONE', #82492, #55609, #60482, .T. ) ; +#45612 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 3.543630035076900485E-34, 0.03429000000000000103 ) ) ; +#45611 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45613 = ORIENTED_EDGE ( 'NONE', *, *, #14438, .F. ) ; +#45614 = AXIS2_PLACEMENT_3D ( 'NONE', #11927, #51346, #35531 ) ; +#45615 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35333 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4949, #100290, #45249 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45616 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79953 ), #39177 ) ; +#45617 = FACE_OUTER_BOUND ( 'NONE', #31473, .T. ) ; +#45618 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.500000000000000000, 0.8299999999999999600 ) ) ; +#45620 = ADVANCED_FACE ( 'NONE', ( #37490 ), #60971, .T. ) ; +#45619 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#45621 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45622 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91299 ), #21183 ) ; +#45623 = VECTOR ( 'NONE', #9304, 1000.000000000000000 ) ; +#45624 = VERTEX_POINT ( 'NONE', #68085 ) ; +#45625 = PRESENTATION_STYLE_ASSIGNMENT (( #92603 ) ) ; +#45626 = ORIENTED_EDGE ( 'NONE', *, *, #90577, .T. ) ; +#45628 = SURFACE_STYLE_FILL_AREA ( #62031 ) ; +#45627 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58716 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99804, #6437, #92251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45630 = DIRECTION ( 'NONE', ( -0.7071067816865476141, 0.7071067806865475314, 0.000000000000000000 ) ) ; +#45629 = SURFACE_STYLE_FILL_AREA ( #22193 ) ; +#45631 = CYLINDRICAL_SURFACE ( 'NONE', #40466, 0.09407705479135430870 ) ; +#45632 = VECTOR ( 'NONE', #39480, 1000.000000000000000 ) ; +#45633 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45634 = SURFACE_SIDE_STYLE ('',( #38031 ) ) ; +#45635 = VECTOR ( 'NONE', #3894, 1000.000000000000000 ) ; +#45636 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 2.567390744878445071E-16 ) ) ; +#45637 = EDGE_CURVE ( 'NONE', #65830, #37993, #69060, .T. ) ; +#45639 = EDGE_CURVE ( 'NONE', #71809, #23403, #12903, .T. ) ; +#45638 = SURFACE_STYLE_FILL_AREA ( #68139 ) ; +#45640 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#45641 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45642 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45643 = FILL_AREA_STYLE_COLOUR ( '', #81361 ) ; +#45644 = ORIENTED_EDGE ( 'NONE', *, *, #11154, .F. ) ; +#45645 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#45646 = STYLED_ITEM ( 'NONE', ( #22849 ), #64413 ) ; +#45647 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#45648 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35959 ) ) ; +#45651 = FACE_OUTER_BOUND ( 'NONE', #8117, .T. ) ; +#45650 = SURFACE_STYLE_FILL_AREA ( #52866 ) ; +#45649 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#45652 = PRESENTATION_STYLE_ASSIGNMENT (( #20323 ) ) ; +#45653 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79767, 'distance_accuracy_value', 'NONE'); +#45654 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88938 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76406, #52445, #15609 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45655 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45656 = VECTOR ( 'NONE', #63936, 1000.000000000000000 ) ; +#45657 = FILL_AREA_STYLE_COLOUR ( '', #85436 ) ; +#45658 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45659 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#45660 = FILL_AREA_STYLE ('',( #85502 ) ) ; +#45661 = ORIENTED_EDGE ( 'NONE', *, *, #37021, .F. ) ; +#45662 = EDGE_CURVE ( 'NONE', #9046, #23198, #83444, .T. ) ; +#45663 = LINE ( 'NONE', #83013, #62530 ) ; +#45664 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45665 = ADVANCED_FACE ( 'NONE', ( #36485 ), #21644, .T. ) ; +#45666 = FILL_AREA_STYLE_COLOUR ( '', #74142 ) ; +#45667 = PLANE ( 'NONE', #41378 ) ; +#45668 = VECTOR ( 'NONE', #51589, 1000.000000000000000 ) ; +#45669 = LINE ( 'NONE', #99717, #1215 ) ; +#45670 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45671 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#45672 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21287 ) ) ; +#45673 = LINE ( 'NONE', #46170, #37665 ) ; +#45674 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45675 = VECTOR ( 'NONE', #52394, 1000.000000000000000 ) ; +#45676 = SURFACE_STYLE_FILL_AREA ( #8328 ) ; +#45677 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45678 = LINE ( 'NONE', #85014, #40475 ) ; +#45679 = LINE ( 'NONE', #61575, #22920 ) ; +#45680 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8991599999999999593 ) ) ; +#45681 = SURFACE_STYLE_FILL_AREA ( #93153 ) ; +#45682 = ADVANCED_FACE ( 'NONE', ( #15462 ), #55341, .T. ) ; +#45683 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990585, 0.000000000000000000 ) ) ; +#45684 = FILL_AREA_STYLE_COLOUR ( '', #18961 ) ; +#45685 = CARTESIAN_POINT ( 'NONE', ( -0.9152290605710889926, -1.296821915455180108, 0.8299999999999999600 ) ) ; +#45686 = ORIENTED_EDGE ( 'NONE', *, *, #61314, .F. ) ; +#45687 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45688 = EDGE_CURVE ( 'NONE', #20872, #75429, #8745, .T. ) ; +#45689 = FILL_AREA_STYLE ('',( #37594 ) ) ; +#45690 = VECTOR ( 'NONE', #1870, 1000.000000000000000 ) ; +#45691 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45692 = VERTEX_POINT ( 'NONE', #9261 ) ; +#45693 = CARTESIAN_POINT ( 'NONE', ( -0.04570195398950489818, -0.9814610950457439698, 0.8300000000000002931 ) ) ; +#45694 = STYLED_ITEM ( 'NONE', ( #50737 ), #86492 ) ; +#45695 = SURFACE_STYLE_USAGE ( .BOTH. , #15570 ) ; +#45697 = EDGE_CURVE ( 'NONE', #17207, #28706, #46618, .T. ) ; +#45696 = LINE ( 'NONE', #46726, #40279 ) ; +#45698 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45699 = EDGE_CURVE ( 'NONE', #89742, #3594, #7136, .T. ) ; +#45700 = ORIENTED_EDGE ( 'NONE', *, *, #1282, .F. ) ; +#45701 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45702 = CARTESIAN_POINT ( 'NONE', ( 8.383087000000001510, 9.651189000000000462, 0.8648700000000000276 ) ) ; +#45703 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37742, 'distance_accuracy_value', 'NONE'); +#45704 = CARTESIAN_POINT ( 'NONE', ( -0.0005258701502700120420, -1.389839611604140046, 0.8300000000000006262 ) ) ; +#45705 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45706 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#45707 = VECTOR ( 'NONE', #52952, 1000.000000000000000 ) ; +#45708 = EDGE_LOOP ( 'NONE', ( #88621, #71764, #88987, #68618 ) ) ; +#45709 = EDGE_LOOP ( 'NONE', ( #88456, #19347, #30250, #3297 ) ) ; +#45710 = PRESENTATION_STYLE_ASSIGNMENT (( #93179 ) ) ; +#45711 = ORIENTED_EDGE ( 'NONE', *, *, #38240, .F. ) ; +#45712 = PLANE ( 'NONE', #52668 ) ; +#45713 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#45714 = AXIS2_PLACEMENT_3D ( 'NONE', #80399, #63582, #72720 ) ; +#45715 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45716 = FACE_OUTER_BOUND ( 'NONE', #17151, .T. ) ; +#45717 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #61587, #82894 ) ; +#45718 = PRESENTATION_STYLE_ASSIGNMENT (( #22792 ) ) ; +#45719 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60449 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61040, #53860, #84491 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45721 = ORIENTED_EDGE ( 'NONE', *, *, #44221, .F. ) ; +#45720 = EDGE_CURVE ( 'NONE', #97394, #3505, #41081, .T. ) ; +#45722 = AXIS2_PLACEMENT_3D ( 'NONE', #35021, #19147, #3841 ) ; +#45723 = ORIENTED_EDGE ( 'NONE', *, *, #62149, .F. ) ; +#45724 = CARTESIAN_POINT ( 'NONE', ( -0.03878568267182790075, 1.364454123474860170, 0.8299999999999999600 ) ) ; +#45725 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16168, 'distance_accuracy_value', 'NONE'); +#45726 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45727 = FILL_AREA_STYLE ('',( #15081 ) ) ; +#45728 = EDGE_CURVE ( 'NONE', #87419, #38287, #7736, .T. ) ; +#45729 = PLANE ( 'NONE', #80947 ) ; +#45730 = CARTESIAN_POINT ( 'NONE', ( 5.519304249750025093, 2.827609249750024034, 0.8648700000000000276 ) ) ; +#45731 = FILL_AREA_STYLE ('',( #94229 ) ) ; +#45732 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70255 ), #52361 ) ; +#45733 = ORIENTED_EDGE ( 'NONE', *, *, #1949, .T. ) ; +#45734 = ADVANCED_FACE ( 'NONE', ( #25210 ), #70614, .T. ) ; +#45736 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#45735 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#45737 = ORIENTED_EDGE ( 'NONE', *, *, #62352, .F. ) ; +#45738 = VERTEX_POINT ( 'NONE', #97099 ) ; +#45739 = AXIS2_PLACEMENT_3D ( 'NONE', #82818, #67466, #76648 ) ; +#45740 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45741 = LINE ( 'NONE', #6421, #49920 ) ; +#45742 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45744 = ADVANCED_FACE ( 'NONE', ( #27205 ), #11762, .T. ) ; +#45743 = DIRECTION ( 'NONE', ( -9.346570452461240360E-17, 1.000000000000000000, -5.551115123125790098E-17 ) ) ; +#45746 = VERTEX_POINT ( 'NONE', #89961 ) ; +#45745 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#45747 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#45748 = PRESENTATION_STYLE_ASSIGNMENT (( #75427 ) ) ; +#45749 = FILL_AREA_STYLE ('',( #68253 ) ) ; +#45750 = EDGE_LOOP ( 'NONE', ( #12169, #26868, #8185, #76780 ) ) ; +#45751 = FACE_OUTER_BOUND ( 'NONE', #74584, .T. ) ; +#45752 = SURFACE_SIDE_STYLE ('',( #70274 ) ) ; +#45753 = ORIENTED_EDGE ( 'NONE', *, *, #76651, .F. ) ; +#45754 = ORIENTED_EDGE ( 'NONE', *, *, #26773, .T. ) ; +#45755 = FACE_OUTER_BOUND ( 'NONE', #26166, .T. ) ; +#45757 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45756 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45758 = PLANE ( 'NONE', #66884 ) ; +#45759 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45760 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45761 = STYLED_ITEM ( 'NONE', ( #53346 ), #18145 ) ; +#45762 = LINE ( 'NONE', #78963, #100288 ) ; +#45763 = SURFACE_STYLE_FILL_AREA ( #14619 ) ; +#45764 = CARTESIAN_POINT ( 'NONE', ( -0.008157340354953810171, -1.074567238704529970, 0.8299999999999999600 ) ) ; +#45766 = EDGE_CURVE ( 'NONE', #93467, #84475, #25525, .T. ) ; +#45765 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #41968 ) ; +#45768 = ADVANCED_FACE ( 'NONE', ( #4201 ), #18996, .T. ) ; +#45767 = SURFACE_STYLE_USAGE ( .BOTH. , #77442 ) ; +#45769 = SURFACE_SIDE_STYLE ('',( #7427 ) ) ; +#45770 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45771 = ORIENTED_EDGE ( 'NONE', *, *, #92482, .F. ) ; +#45772 = CYLINDRICAL_SURFACE ( 'NONE', #80704, 0.009999999999999998473 ) ; +#45773 = ORIENTED_EDGE ( 'NONE', *, *, #81103, .T. ) ; +#45774 = MANIFOLD_SOLID_BREP ( 'ÊäÈë153', #98902 ) ; +#45776 = CARTESIAN_POINT ( 'NONE', ( -0.9654900160113228935, -1.460253732877538679, 0.8099999999996493338 ) ) ; +#45775 = AXIS2_PLACEMENT_3D ( 'NONE', #77696, #61898, #7656 ) ; +#45777 = CARTESIAN_POINT ( 'NONE', ( 1.119708175802679895, -1.130592060098940088, 0.8299999999999999600 ) ) ; +#45778 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73536 ), #11478 ) ; +#45779 = FILL_AREA_STYLE ('',( #61170 ) ) ; +#45780 = VECTOR ( 'NONE', #63042, 1000.000000000000000 ) ; +#45781 = PRESENTATION_STYLE_ASSIGNMENT (( #68772 ) ) ; +#45782 = PRESENTATION_STYLE_ASSIGNMENT (( #14631 ) ) ; +#45783 = FACE_OUTER_BOUND ( 'NONE', #46195, .T. ) ; +#45784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45785 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#45786 = EDGE_LOOP ( 'NONE', ( #56496, #31470, #57589, #90309 ) ) ; +#45787 = LINE ( 'NONE', #38180, #16627 ) ; +#45788 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45789 = ADVANCED_FACE ( 'NONE', ( #59872 ), #90463, .T. ) ; +#45790 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45791 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45792 = EDGE_CURVE ( 'NONE', #67944, #23538, #44976, .T. ) ; +#45793 = CARTESIAN_POINT ( 'NONE', ( 1.890937141840999924, -1.269147371132230084, 0.8299999999999999600 ) ) ; +#45794 = SURFACE_STYLE_USAGE ( .BOTH. , #84638 ) ; +#45795 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#45796 = SURFACE_SIDE_STYLE ('',( #14646 ) ) ; +#45797 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62199 ), #73553 ) ; +#45798 = DIRECTION ( 'NONE', ( -0.7490054809316831763, 0.6625638003500476936, 0.000000000000000000 ) ) ; +#45799 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#45800 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#45801 = STYLED_ITEM ( 'NONE', ( #57822 ), #2198 ) ; +#45802 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67804 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17383, #81226, #63399 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45803 = CARTESIAN_POINT ( 'NONE', ( 1.275362369208429936, -0.9706035140527151661, 0.8299999999999995159 ) ) ; +#45804 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79469, #9426, #36529, #43641, #75805, #81984, #97734, #35529, #42668, #73811, #36026, #74312, #3851, #20160, #35030 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000001665, 0.1875000000000002498, 0.2500000000000003331, 0.4999999999999998890, 0.6250000000000005551, 0.7500000000000012212, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45805 = LINE ( 'NONE', #23901, #4541 ) ; +#45806 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#45807 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8099999999999827338 ) ) ; +#45808 = VERTEX_POINT ( 'NONE', #51692 ) ; +#45809 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#45810 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45811 = CARTESIAN_POINT ( 'NONE', ( 1.664835065683849979, -1.443372874996269983, 0.8299999999999977396 ) ) ; +#45812 = CARTESIAN_POINT ( 'NONE', ( 9.535670999999998898, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#45813 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96058 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54004, #77992, #7947 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45814 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#45815 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65380 ) ) ; +#45816 = AXIS2_PLACEMENT_3D ( 'NONE', #51076, #37256, #60254 ) ; +#45817 = VERTEX_POINT ( 'NONE', #84315 ) ; +#45818 = EDGE_CURVE ( 'NONE', #26569, #48469, #45463, .T. ) ; +#45819 = VECTOR ( 'NONE', #85549, 1000.000000000000114 ) ; +#45820 = PLANE ( 'NONE', #36420 ) ; +#45821 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#45822 = EDGE_CURVE ( 'NONE', #20872, #49407, #100017, .T. ) ; +#45823 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#45824 = VERTEX_POINT ( 'NONE', #68960 ) ; +#45825 = VERTEX_POINT ( 'NONE', #30169 ) ; +#45826 = VECTOR ( 'NONE', #33790, 1000.000000000000000 ) ; +#45827 = STYLED_ITEM ( 'NONE', ( #75639 ), #33908 ) ; +#45828 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45829 = ORIENTED_EDGE ( 'NONE', *, *, #53431, .T. ) ; +#45830 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45831 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45832 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#45833 = SURFACE_SIDE_STYLE ('',( #31064 ) ) ; +#45834 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45835 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56477 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54501, #22317, #15634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45836 = SURFACE_STYLE_FILL_AREA ( #39221 ) ; +#45837 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32853 ), #44258 ) ; +#45838 = PRODUCT_CONTEXT ( 'NONE', #58646, 'mechanical' ) ; +#45839 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#45840 = SURFACE_STYLE_FILL_AREA ( #23411 ) ; +#45843 = ORIENTED_EDGE ( 'NONE', *, *, #21337, .T. ) ; +#45842 = ORIENTED_EDGE ( 'NONE', *, *, #96723, .F. ) ; +#45841 = ADVANCED_FACE ( 'NONE', ( #61373 ), #38367, .F. ) ; +#45844 = ORIENTED_EDGE ( 'NONE', *, *, #45637, .F. ) ; +#45845 = SURFACE_STYLE_FILL_AREA ( #92805 ) ; +#45846 = AXIS2_PLACEMENT_3D ( 'NONE', #41453, #11206, #95016 ) ; +#45847 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15914, 'distance_accuracy_value', 'NONE'); +#45849 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#45848 = FACE_OUTER_BOUND ( 'NONE', #74898, .T. ) ; +#45850 = VERTEX_POINT ( 'NONE', #87331 ) ; +#45852 = ADVANCED_FACE ( 'NONE', ( #69470 ), #24595, .T. ) ; +#45851 = ORIENTED_EDGE ( 'NONE', *, *, #51203, .T. ) ; +#45853 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49364 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18412, #2119, #33770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45854 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 2.100000000000000089, 0.000000000000000000 ) ) ; +#45855 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#45857 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#45856 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88269 ) ) ; +#45858 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44085 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100469, #91924, #30619 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45859 = CARTESIAN_POINT ( 'NONE', ( -0.3688392660424539837, -1.039320398944010071, 0.8299999999999999600 ) ) ; +#45860 = ORIENTED_EDGE ( 'NONE', *, *, #90476, .F. ) ; +#45861 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#45862 = ORIENTED_EDGE ( 'NONE', *, *, #31913, .T. ) ; +#45863 = ORIENTED_EDGE ( 'NONE', *, *, #78685, .F. ) ; +#45864 = PRESENTATION_STYLE_ASSIGNMENT (( #52581 ) ) ; +#45865 = SURFACE_STYLE_USAGE ( .BOTH. , #32114 ) ; +#45866 = VECTOR ( 'NONE', #77904, 1000.000000000000000 ) ; +#45867 = EDGE_CURVE ( 'NONE', #29371, #31665, #48038, .T. ) ; +#45868 = ORIENTED_EDGE ( 'NONE', *, *, #4097, .T. ) ; +#45869 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45870 = VERTEX_POINT ( 'NONE', #1583 ) ; +#45871 = CARTESIAN_POINT ( 'NONE', ( 0.01546163603480650052, -1.327673353236110021, 0.8299999999999999600 ) ) ; +#45872 = PLANE ( 'NONE', #99790 ) ; +#45874 = ORIENTED_EDGE ( 'NONE', *, *, #28385, .F. ) ; +#45873 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77629 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10359, #3309, #73270 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45875 = EDGE_CURVE ( 'NONE', #52681, #4348, #94884, .T. ) ; +#45876 = VERTEX_POINT ( 'NONE', #94964 ) ; +#45878 = LINE ( 'NONE', #93349, #60101 ) ; +#45877 = LINE ( 'NONE', #8027, #37487 ) ; +#45879 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45880 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.9000000000000020206, 0.1829999999999619986 ) ) ; +#45881 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4170 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59072, #14018, #43694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45882 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#45884 = VECTOR ( 'NONE', #45231, 1000.000000000000000 ) ; +#45883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45885 = ADVANCED_FACE ( 'NONE', ( #17373 ), #79702, .T. ) ; +#45886 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45887 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, 0.6500000000000000222 ) ) ; +#45889 = SURFACE_STYLE_USAGE ( .BOTH. , #68391 ) ; +#45888 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35101, 'distance_accuracy_value', 'NONE'); +#45890 = ORIENTED_EDGE ( 'NONE', *, *, #66249, .F. ) ; +#45891 = CARTESIAN_POINT ( 'NONE', ( 0.4459649354204920368, -1.149076952450200029, 0.8100000000000000533 ) ) ; +#45892 = CARTESIAN_POINT ( 'NONE', ( 0.08991555325362560191, -1.292112914554750080, 0.8100000000000000533 ) ) ; +#45893 = ORIENTED_EDGE ( 'NONE', *, *, #27384, .T. ) ; +#45894 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86032 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4685, #26199, #65990 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45895 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -2.100000000000000533, 0.1829999999999500082 ) ) ; +#45896 = EDGE_CURVE ( 'NONE', #34253, #26606, #1074, .T. ) ; +#45897 = EDGE_CURVE ( 'NONE', #61368, #56085, #39519, .T. ) ; +#45898 = FACE_OUTER_BOUND ( 'NONE', #72069, .T. ) ; +#45899 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45900 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45901 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#45902 = CARTESIAN_POINT ( 'NONE', ( 1.715925389647680044, -0.9637996098261990552, 0.8299999999999999600 ) ) ; +#45903 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45904 = DIRECTION ( 'NONE', ( 0.8186165608382620640, 0.5743404272044030368, 0.000000000000000000 ) ) ; +#45905 = EDGE_CURVE ( 'NONE', #24848, #43011, #64861, .T. ) ; +#45906 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, -0.2349999999999999867 ) ) ; +#45907 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45908 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4638, #66934, #43956, #75118 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#45909 = AXIS2_PLACEMENT_3D ( 'NONE', #8931, #40179, #71306 ) ; +#45910 = EDGE_CURVE ( 'NONE', #14100, #18355, #49093, .T. ) ; +#45911 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99696 ), #88383 ) ; +#45912 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70427 ), #72065 ) ; +#45914 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#45913 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45915 = LINE ( 'NONE', #77094, #63643 ) ; +#45916 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57438 ) ) ; +#45917 = CARTESIAN_POINT ( 'NONE', ( 9.231614875125044861, 3.725634875125043877, 0.8991599999999999593 ) ) ; +#45918 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77610 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15510, #5597, #28136 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45919 = EDGE_LOOP ( 'NONE', ( #85442, #56220, #443, #8608 ) ) ; +#45920 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#45921 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47339 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14742, #77572, #7532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#45922 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45048, 'distance_accuracy_value', 'NONE'); +#45923 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9479, 'distance_accuracy_value', 'NONE'); +#45924 = LINE ( 'NONE', #46961, #71065 ) ; +#45925 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45926 = SURFACE_SIDE_STYLE ('',( #14774 ) ) ; +#45927 = PLANE ( 'NONE', #60177 ) ; +#45928 = FILL_AREA_STYLE ('',( #22484 ) ) ; +#45929 = VECTOR ( 'NONE', #89806, 1000.000000000000000 ) ; +#45930 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#45931 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#45932 = VERTEX_POINT ( 'NONE', #87841 ) ; +#45933 = SURFACE_STYLE_USAGE ( .BOTH. , #93409 ) ; +#45934 = ORIENTED_EDGE ( 'NONE', *, *, #100383, .T. ) ; +#45935 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999356, -0.01500000000000001332, -0.2458578643762690530 ) ) ; +#45937 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100486, 'distance_accuracy_value', 'NONE'); +#45936 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90003 ) ) ; +#45938 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49276, 'distance_accuracy_value', 'NONE'); +#45939 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45940 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -2.300000000000000266, -0.02000000000000000042 ) ) ; +#45941 = CARTESIAN_POINT ( 'NONE', ( 9.514457000000000164, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#45942 = FILL_AREA_STYLE_COLOUR ( '', #57585 ) ; +#45943 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, -0.3000000000000001554, 0.000000000000000000 ) ) ; +#45944 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45945 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#45946 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#45947 = EDGE_CURVE ( 'NONE', #49689, #51947, #81212, .T. ) ; +#45948 = ORIENTED_EDGE ( 'NONE', *, *, #66687, .F. ) ; +#45949 = FILL_AREA_STYLE ('',( #98520 ) ) ; +#45950 = EDGE_LOOP ( 'NONE', ( #28421, #59997, #60440, #27756 ) ) ; +#45951 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#45952 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6764 ), #67202 ) ; +#45953 = ORIENTED_EDGE ( 'NONE', *, *, #57147, .F. ) ; +#45954 = AXIS2_PLACEMENT_3D ( 'NONE', #91490, #44990, #61875 ) ; +#45955 = CARTESIAN_POINT ( 'NONE', ( 1.161760760428500072, -1.440849955440170138, 0.8100000000000000533 ) ) ; +#45956 = SURFACE_STYLE_USAGE ( .BOTH. , #38852 ) ; +#45957 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#45958 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#45959 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45960 = CARTESIAN_POINT ( 'NONE', ( -0.1838731702863170558, 1.340133138901687060, 0.8100000000000000533 ) ) ; +#45962 = ORIENTED_EDGE ( 'NONE', *, *, #63939, .T. ) ; +#45961 = ORIENTED_EDGE ( 'NONE', *, *, #89433, .F. ) ; +#45963 = STYLED_ITEM ( 'NONE', ( #45718 ), #82058 ) ; +#45964 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01499999999999998383, 0.1400000000000000133 ) ) ; +#45965 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639962, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#45966 = EDGE_LOOP ( 'NONE', ( #8169, #50710, #89139, #98813 ) ) ; +#45967 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45969 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#45968 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#45970 = ORIENTED_EDGE ( 'NONE', *, *, #2832, .F. ) ; +#45972 = ADVANCED_FACE ( 'NONE', ( #89348 ), #41893, .T. ) ; +#45971 = ORIENTED_EDGE ( 'NONE', *, *, #79667, .T. ) ; +#45973 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.03429000000000000103 ) ) ; +#45974 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45975 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#45976 = FILL_AREA_STYLE ('',( #71022 ) ) ; +#45977 = SURFACE_SIDE_STYLE ('',( #99046 ) ) ; +#45978 = SURFACE_STYLE_USAGE ( .BOTH. , #77159 ) ; +#45979 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.7099999999999999645, -8.923404656952791787E-18 ) ) ; +#45980 = ORIENTED_EDGE ( 'NONE', *, *, #8264, .T. ) ; +#45981 = ORIENTED_EDGE ( 'NONE', *, *, #53080, .T. ) ; +#45982 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#45983 = AXIS2_PLACEMENT_3D ( 'NONE', #1208, #45745, #28963 ) ; +#45984 = VERTEX_POINT ( 'NONE', #73538 ) ; +#45985 = STYLED_ITEM ( 'NONE', ( #54366 ), #86946 ) ; +#45986 = AXIS2_PLACEMENT_3D ( 'NONE', #89571, #44100, #35970 ) ; +#45987 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#45988 = CIRCLE ( 'NONE', #59120, 0.1200000000000000927 ) ; +#45989 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47646 ), #68811 ) ; +#45991 = ORIENTED_EDGE ( 'NONE', *, *, #19335, .T. ) ; +#45990 = LINE ( 'NONE', #7634, #29761 ) ; +#45992 = STYLED_ITEM ( 'NONE', ( #78585 ), #8728 ) ; +#45993 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#45994 = FILL_AREA_STYLE ('',( #84824 ) ) ; +#45995 = SURFACE_STYLE_USAGE ( .BOTH. , #13825 ) ; +#45996 = ORIENTED_EDGE ( 'NONE', *, *, #81038, .T. ) ; +#45997 = FILL_AREA_STYLE_COLOUR ( '', #86807 ) ; +#45998 = ORIENTED_EDGE ( 'NONE', *, *, #17078, .T. ) ; +#45999 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52624 ) ) ; +#46000 = CARTESIAN_POINT ( 'NONE', ( 0.05660856691479519698, -0.9907810524907130212, 0.8299999999999988498 ) ) ; +#46001 = LINE ( 'NONE', #12820, #49818 ) ; +#46002 = ORIENTED_EDGE ( 'NONE', *, *, #33992, .F. ) ; +#46003 = LINE ( 'NONE', #70021, #55222 ) ; +#46005 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.1199999999999999956, 0.8499999999999999778 ) ) ; +#46004 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46006 = SURFACE_STYLE_FILL_AREA ( #37899 ) ; +#46007 = CARTESIAN_POINT ( 'NONE', ( 2.300000000000000266, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#46008 = VERTEX_POINT ( 'NONE', #3588 ) ; +#46009 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55566 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12183, #20939, #90883 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46010 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#46011 = EDGE_CURVE ( 'NONE', #35363, #85114, #27875, .T. ) ; +#46012 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.300000000000000266, 1.048695503451051965E-76 ) ) ; +#46014 = FILL_AREA_STYLE ('',( #13853 ) ) ; +#46013 = LINE ( 'NONE', #44045, #56021 ) ; +#46015 = SURFACE_STYLE_FILL_AREA ( #22580 ) ; +#46016 = FILL_AREA_STYLE ('',( #47577 ) ) ; +#46017 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99616, #29770, #29289, #60463, #53765, #45068, #21619, #46592, #91068, #84898, #76234, #60950, #85405, #83420, #14914, #7216, #69565, #100594, #38956 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.320612373527916158E-05, 4.492052686938633892E-05, 6.582062287974524938E-05, 8.605494144861170901E-05, 0.0001059136079145904123, 0.0001256087639101623481, 0.0001452127442685411979, 0.0001650429405876201704, 0.0001850370302419335883, 0.0002052205854468329297, 0.0002258575965929353346, 0.0002469788263569381919, 0.0002682616920459039798, 0.0002891959060428054640, 0.0003100051045178446531, 0.0003307427320208417552 ), + .UNSPECIFIED. ) ; +#46018 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#46019 = LINE ( 'NONE', #38917, #27925 ) ; +#46020 = ORIENTED_EDGE ( 'NONE', *, *, #34444, .F. ) ; +#46021 = VECTOR ( 'NONE', #94851, 1000.000000000000000 ) ; +#46022 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#46023 = EDGE_CURVE ( 'NONE', #57703, #84697, #27087, .T. ) ; +#46024 = ORIENTED_EDGE ( 'NONE', *, *, #50114, .F. ) ; +#46025 = CYLINDRICAL_SURFACE ( 'NONE', #39015, 0.04999999999999991257 ) ; +#46028 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46027 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.449999999999999956, -11.32000000000000028 ) ) ; +#46026 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29807 ), #62421 ) ; +#46029 = SURFACE_STYLE_FILL_AREA ( #77209 ) ; +#46030 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#46031 = VECTOR ( 'NONE', #55293, 1000.000000000000000 ) ; +#46032 = VERTEX_POINT ( 'NONE', #35261 ) ; +#46033 = FILL_AREA_STYLE_COLOUR ( '', #13786 ) ; +#46034 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46035 = VECTOR ( 'NONE', #94822, 1000.000000000000114 ) ; +#46036 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, -3.602442418445169851E-17, -0.8499999999999999778 ) ) ; +#46037 = STYLED_ITEM ( 'NONE', ( #78851 ), #18712 ) ; +#46038 = VECTOR ( 'NONE', #14760, 1000.000000000000000 ) ; +#46039 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#46040 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#46041 = PRESENTATION_STYLE_ASSIGNMENT (( #77734 ) ) ; +#46042 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#46043 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#46044 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46045 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90114 ), #387 ) ; +#46047 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38018 ), #80376 ) ; +#46046 = FACE_OUTER_BOUND ( 'NONE', #8627, .T. ) ; +#46048 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62102, 'distance_accuracy_value', 'NONE'); +#46049 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46050 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852913999999999728, 0.8991599999999999593 ) ) ; +#46051 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#46052 = ORIENTED_EDGE ( 'NONE', *, *, #65873, .T. ) ; +#46053 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46055 = VERTEX_POINT ( 'NONE', #51073 ) ; +#46054 = CIRCLE ( 'NONE', #75480, 0.009999999999999998473 ) ; +#46056 = PRESENTATION_STYLE_ASSIGNMENT (( #29283 ) ) ; +#46057 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81388, 'distance_accuracy_value', 'NONE'); +#46058 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39053, 'distance_accuracy_value', 'NONE'); +#46059 = VECTOR ( 'NONE', #70818, 1000.000000000000000 ) ; +#46060 = PLANE ( 'NONE', #81478 ) ; +#46061 = CARTESIAN_POINT ( 'NONE', ( 3.924999999999999822, 0.2999999999999999889, -12.44500000000000028 ) ) ; +#46062 = FACE_OUTER_BOUND ( 'NONE', #4847, .T. ) ; +#46063 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55981 ), #62464 ) ; +#46064 = FACE_OUTER_BOUND ( 'NONE', #26856, .T. ) ; +#46065 = PLANE ( 'NONE', #4767 ) ; +#46066 = PLANE ( 'NONE', #93359 ) ; +#46067 = ADVANCED_FACE ( 'NONE', ( #82209 ), #90343, .T. ) ; +#46068 = ORIENTED_EDGE ( 'NONE', *, *, #95082, .F. ) ; +#46069 = LINE ( 'NONE', #62468, #63988 ) ; +#46070 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46071 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46072 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84741, 'distance_accuracy_value', 'NONE'); +#46073 = PRESENTATION_STYLE_ASSIGNMENT (( #84909 ) ) ; +#46074 = FILL_AREA_STYLE_COLOUR ( '', #83033 ) ; +#46075 = ORIENTED_EDGE ( 'NONE', *, *, #49006, .F. ) ; +#46076 = SURFACE_STYLE_FILL_AREA ( #14926 ) ; +#46077 = FACE_OUTER_BOUND ( 'NONE', #814, .T. ) ; +#46078 = LINE ( 'NONE', #34238, #41385 ) ; +#46079 = PRESENTATION_STYLE_ASSIGNMENT (( #65732 ) ) ; +#46080 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46081 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#46082 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46084 = ORIENTED_EDGE ( 'NONE', *, *, #67690, .F. ) ; +#46083 = STYLED_ITEM ( 'NONE', ( #74949 ), #70701 ) ; +#46085 = SURFACE_STYLE_FILL_AREA ( #84921 ) ; +#46086 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68544, 'distance_accuracy_value', 'NONE'); +#46087 = LINE ( 'NONE', #24703, #6971 ) ; +#46088 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46089 = AXIS2_PLACEMENT_3D ( 'NONE', #61220, #31056, #23398 ) ; +#46091 = EDGE_CURVE ( 'NONE', #8714, #28482, #22399, .T. ) ; +#46090 = ORIENTED_EDGE ( 'NONE', *, *, #46462, .T. ) ; +#46093 = LINE ( 'NONE', #44126, #42953 ) ; +#46092 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46094 = FILL_AREA_STYLE ('',( #84438 ) ) ; +#46095 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46096 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#46097 = ORIENTED_EDGE ( 'NONE', *, *, #13156, .F. ) ; +#46098 = ORIENTED_EDGE ( 'NONE', *, *, #21606, .T. ) ; +#46099 = CARTESIAN_POINT ( 'NONE', ( -0.5614853896103890740, 0.6899999999999999467, 0.1493506493506489563 ) ) ; +#46101 = EDGE_CURVE ( 'NONE', #54674, #3678, #36357, .T. ) ; +#46100 = CIRCLE ( 'NONE', #67342, 0.2000000000000005107 ) ; +#46102 = ORIENTED_EDGE ( 'NONE', *, *, #71193, .T. ) ; +#46103 = MANIFOLD_SOLID_BREP ( 'ÊäÈë136', #78004 ) ; +#46104 = VERTEX_POINT ( 'NONE', #12157 ) ; +#46106 = ORIENTED_EDGE ( 'NONE', *, *, #2115, .F. ) ; +#46105 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#46107 = SURFACE_STYLE_USAGE ( .BOTH. , #53321 ) ; +#46110 = PRESENTATION_STYLE_ASSIGNMENT (( #70123 ) ) ; +#46109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46108 = AXIS2_PLACEMENT_3D ( 'NONE', #99709, #30347, #70177 ) ; +#46111 = VECTOR ( 'NONE', #23004, 1000.000000000000000 ) ; +#46112 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46113 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#46114 = ORIENTED_EDGE ( 'NONE', *, *, #28372, .T. ) ; +#46115 = FACE_OUTER_BOUND ( 'NONE', #75425, .T. ) ; +#46117 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000622, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#46116 = AXIS2_PLACEMENT_3D ( 'NONE', #84419, #39459, #15452 ) ; +#46118 = PLANE ( 'NONE', #59079 ) ; +#46119 = EDGE_LOOP ( 'NONE', ( #16583, #38718, #24887, #77287 ) ) ; +#46120 = ADVANCED_FACE ( 'NONE', ( #54589 ), #29075, .T. ) ; +#46121 = PRESENTATION_STYLE_ASSIGNMENT (( #29337 ) ) ; +#46122 = SURFACE_STYLE_FILL_AREA ( #14965 ) ; +#46123 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75534 ) ) ; +#46124 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71885 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36919, #45521, #6685 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46125 = FILL_AREA_STYLE_COLOUR ( '', #49957 ) ; +#46126 = VERTEX_POINT ( 'NONE', #38239 ) ; +#46128 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#46127 = CARTESIAN_POINT ( 'NONE', ( 1.799634867437249985, -1.074567238704529970, 0.8099999999999998312 ) ) ; +#46129 = VERTEX_POINT ( 'NONE', #78047 ) ; +#46130 = VECTOR ( 'NONE', #32134, 1000.000000000000000 ) ; +#46131 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66240, #89223, #19251, #36121 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46132 = AXIS2_PLACEMENT_3D ( 'NONE', #33715, #32699, #25553 ) ; +#46134 = FACE_OUTER_BOUND ( 'NONE', #67549, .T. ) ; +#46133 = FILL_AREA_STYLE ('',( #50845 ) ) ; +#46135 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#46136 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36428 ), #59276 ) ; +#46137 = AXIS2_PLACEMENT_3D ( 'NONE', #48246, #40069, #32911 ) ; +#46138 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46139 = EDGE_CURVE ( 'NONE', #24193, #33859, #46365, .T. ) ; +#46140 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46141 = ORIENTED_EDGE ( 'NONE', *, *, #53602, .T. ) ; +#46142 = ORIENTED_EDGE ( 'NONE', *, *, #74875, .F. ) ; +#46143 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46144 = SURFACE_SIDE_STYLE ('',( #45629 ) ) ; +#46145 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93757, 'distance_accuracy_value', 'NONE'); +#46146 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67359 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49296, #87586, #45969 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46147 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46148 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46149 = SURFACE_STYLE_USAGE ( .BOTH. , #14496 ) ; +#46150 = EDGE_CURVE ( 'NONE', #19242, #7870, #7997, .T. ) ; +#46151 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#46152 = VERTEX_POINT ( 'NONE', #86709 ) ; +#46153 = CARTESIAN_POINT ( 'NONE', ( -1.233538577444069917, -1.130592060098940088, 0.8300000000000002931 ) ) ; +#46154 = FILL_AREA_STYLE ('',( #100198 ) ) ; +#46155 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77165 ), #85323 ) ; +#46156 = SURFACE_STYLE_USAGE ( .BOTH. , #92622 ) ; +#46157 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.000000000000000000 ) ) ; +#46158 = FACE_OUTER_BOUND ( 'NONE', #49423, .T. ) ; +#46159 = FILL_AREA_STYLE ('',( #15003 ) ) ; +#46160 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000311, -0.02000000000000000042 ) ) ; +#46161 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16793 ) ) ; +#46162 = SURFACE_STYLE_USAGE ( .BOTH. , #82637 ) ; +#46163 = ORIENTED_EDGE ( 'NONE', *, *, #65313, .T. ) ; +#46164 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46165 = SURFACE_STYLE_USAGE ( .BOTH. , #14515 ) ; +#46166 = CARTESIAN_POINT ( 'NONE', ( 0.01532804002844260008, -1.344848644821849959, 0.8100000000000000533 ) ) ; +#46167 = VECTOR ( 'NONE', #221, 1000.000000000000000 ) ; +#46168 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#46169 = SURFACE_STYLE_USAGE ( .BOTH. , #7323 ) ; +#46170 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#46171 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, 0.000000000000000000 ) ) ; +#46172 = FILL_AREA_STYLE ('',( #31905 ) ) ; +#46173 = VECTOR ( 'NONE', #5978, 1000.000000000000000 ) ; +#46174 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31494 ) ) ; +#46175 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8648700000000000276 ) ) ; +#46176 = SURFACE_SIDE_STYLE ('',( #53882 ) ) ; +#46177 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46178 = SURFACE_SIDE_STYLE ('',( #69149 ) ) ; +#46180 = ADVANCED_FACE ( 'NONE', ( #39742 ), #77522, .T. ) ; +#46179 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #21296, #3490, #59151, #74937, #73930, #59661, #83099, #3974, #83606, #65774, #74441, #12052, #35657, #89258, #96873, #82601, #35152, #27987, #19285 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.366134600599807235E-05, 2.678053936399086277E-05, 3.925672662558360747E-05, 5.134489543513030157E-05, 6.322496733117226580E-05, 7.487673038755930459E-05, 8.649796808712875327E-05, 9.812875356678275169E-05, 0.0001098766569990736511, 0.0001215772214741423347, 0.0001333030571762210408, 0.0001451137840694612579, 0.0001571522639181525797, 0.0001694924733769886862, 0.0001820943669839380791, 0.0001951167467603312587 ), + .UNSPECIFIED. ) ; +#46181 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8648700000000000276 ) ) ; +#46182 = CARTESIAN_POINT ( 'NONE', ( 9.535670500500176061, 3.110451500500174493, 0.8991599999999999593 ) ) ; +#46183 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52794 ) ) ; +#46184 = FACE_OUTER_BOUND ( 'NONE', #66790, .T. ) ; +#46185 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46186 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26859, 'distance_accuracy_value', 'NONE'); +#46187 = LINE ( 'NONE', #54411, #19630 ) ; +#46188 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45206, 'distance_accuracy_value', 'NONE'); +#46189 = CARTESIAN_POINT ( 'NONE', ( 0.6761799387799150018, 3.099999999999980105, 0.000000000000000000 ) ) ; +#46190 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28766 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79402, #2307, #56952 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46191 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#46192 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46193 = SURFACE_STYLE_FILL_AREA ( #15035 ) ; +#46194 = EDGE_CURVE ( 'NONE', #88040, #40171, #77030, .T. ) ; +#46195 = EDGE_LOOP ( 'NONE', ( #33968, #45353, #5258, #55837 ) ) ; +#46196 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57421, 'distance_accuracy_value', 'NONE'); +#46197 = SURFACE_STYLE_USAGE ( .BOTH. , #61081 ) ; +#46198 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67216 ) ) ; +#46199 = SURFACE_SIDE_STYLE ('',( #38088 ) ) ; +#46200 = VERTEX_POINT ( 'NONE', #79061 ) ; +#46201 = SURFACE_SIDE_STYLE ('',( #39588 ) ) ; +#46202 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46203 = FILL_AREA_STYLE ('',( #94692 ) ) ; +#46204 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.583333333333333481, 0.000000000000000000 ) ) ; +#46205 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666633301, -1.899999999999999911, 3.495651678169922342E-76 ) ) ; +#46206 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46207 = ORIENTED_EDGE ( 'NONE', *, *, #36112, .F. ) ; +#46208 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46209 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81772, 'distance_accuracy_value', 'NONE'); +#46210 = CARTESIAN_POINT ( 'NONE', ( -1.723820061220085353, 3.100000000000000533, 0.000000000000000000 ) ) ; +#46211 = SURFACE_STYLE_FILL_AREA ( #15056 ) ; +#46212 = ORIENTED_EDGE ( 'NONE', *, *, #70176, .T. ) ; +#46213 = ORIENTED_EDGE ( 'NONE', *, *, #46316, .F. ) ; +#46214 = SURFACE_STYLE_USAGE ( .BOTH. , #8876 ) ; +#46215 = STYLED_ITEM ( 'NONE', ( #30267 ), #67427 ) ; +#46216 = VERTEX_POINT ( 'NONE', #54060 ) ; +#46217 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999430, 7.437945000000000917, 0.8991599999999999593 ) ) ; +#46218 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#46219 = CARTESIAN_POINT ( 'NONE', ( 0.5426878470553200273, -1.110278784363659899, 0.8299999999999999600 ) ) ; +#46220 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46221 = EDGE_CURVE ( 'NONE', #79084, #86756, #71390, .T. ) ; +#46222 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.266666666666639962, 3.495651678169978796E-76 ) ) ; +#46223 = EDGE_CURVE ( 'NONE', #59792, #72195, #24961, .T. ) ; +#46224 = ORIENTED_EDGE ( 'NONE', *, *, #96843, .F. ) ; +#46225 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86153 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23469, #62791, #32139 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46226 = ORIENTED_EDGE ( 'NONE', *, *, #76912, .T. ) ; +#46227 = FACE_OUTER_BOUND ( 'NONE', #31916, .T. ) ; +#46228 = LINE ( 'NONE', #15603, #99452 ) ; +#46230 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46229 = FILL_AREA_STYLE ('',( #29452 ) ) ; +#46232 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#46231 = VECTOR ( 'NONE', #57343, 1000.000000000000000 ) ; +#46233 = ORIENTED_EDGE ( 'NONE', *, *, #98188, .F. ) ; +#46234 = EDGE_CURVE ( 'NONE', #10112, #96599, #58121, .T. ) ; +#46235 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46236 = SURFACE_STYLE_USAGE ( .BOTH. , #99779 ) ; +#46237 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46238 = AXIS2_PLACEMENT_3D ( 'NONE', #98595, #28734, #68020 ) ; +#46239 = LINE ( 'NONE', #86083, #4158 ) ; +#46240 = ORIENTED_EDGE ( 'NONE', *, *, #29005, .F. ) ; +#46241 = EDGE_CURVE ( 'NONE', #12696, #91950, #84976, .T. ) ; +#46242 = CARTESIAN_POINT ( 'NONE', ( 4.387933249749911724, 8.569316249749912018, 0.8991599999999999593 ) ) ; +#46243 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90306 ) ) ; +#46244 = EDGE_LOOP ( 'NONE', ( #16317, #62144, #37499, #90856 ) ) ; +#46245 = VECTOR ( 'NONE', #23541, 1000.000000000000000 ) ; +#46246 = ORIENTED_EDGE ( 'NONE', *, *, #37480, .T. ) ; +#46247 = FILL_AREA_STYLE_COLOUR ( '', #11796 ) ; +#46248 = PRESENTATION_STYLE_ASSIGNMENT (( #17141 ) ) ; +#46249 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46250 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96204 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40823, #94397, #30585 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46251 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46252 = VERTEX_POINT ( 'NONE', #49943 ) ; +#46253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46254 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#46255 = EDGE_CURVE ( 'NONE', #71141, #87344, #41278, .T. ) ; +#46256 = FILL_AREA_STYLE ('',( #7404 ) ) ; +#46257 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46258 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34967 ), #69127 ) ; +#46259 = ORIENTED_EDGE ( 'NONE', *, *, #58602, .T. ) ; +#46261 = FACE_OUTER_BOUND ( 'NONE', #3119, .T. ) ; +#46260 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#46262 = FILL_AREA_STYLE_COLOUR ( '', #2129 ) ; +#46263 = ORIENTED_EDGE ( 'NONE', *, *, #45208, .F. ) ; +#46264 = EDGE_LOOP ( 'NONE', ( #94661, #35843, #100537, #42675 ) ) ; +#46265 = FACE_OUTER_BOUND ( 'NONE', #22152, .T. ) ; +#46266 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99968 ) ) ; +#46268 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#46267 = CARTESIAN_POINT ( 'NONE', ( 1.182009071931110045, -1.515071875619850017, 0.8299999999999999600 ) ) ; +#46269 = SURFACE_STYLE_USAGE ( .BOTH. , #61153 ) ; +#46271 = ADVANCED_FACE ( 'NONE', ( #3472 ), #72905, .F. ) ; +#46270 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46273 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16908 ) ) ; +#46272 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46274 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#46275 = CIRCLE ( 'NONE', #36573, 0.2000000000066392836 ) ; +#46276 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#46277 = PLANE ( 'NONE', #32540 ) ; +#46278 = ORIENTED_EDGE ( 'NONE', *, *, #30941, .F. ) ; +#46279 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46280 = ORIENTED_EDGE ( 'NONE', *, *, #94083, .F. ) ; +#46281 = EDGE_CURVE ( 'NONE', #33332, #78778, #34625, .T. ) ; +#46282 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59836, #52151, #83279, #13239, #44434, #75607, #5617, #98989, #23510, #8078, #86796, #77615 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 1, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999954481, 0.3749999999999930611, 0.4374999999999918954, 0.4687499999999914513, 0.4999999999999911182, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46283 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46284 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46285 = VECTOR ( 'NONE', #6517, 1000.000000000000000 ) ; +#46286 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#46287 = AXIS2_PLACEMENT_3D ( 'NONE', #98570, #20048, #89014 ) ; +#46288 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#46289 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46290 = PRESENTATION_STYLE_ASSIGNMENT (( #16156 ) ) ; +#46291 = VERTEX_POINT ( 'NONE', #25454 ) ; +#46292 = PRESENTATION_STYLE_ASSIGNMENT (( #61678 ) ) ; +#46293 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#46294 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81680, #10091, #41356, #11609, #72468, #3557, #2542, #33700, #95936, #42858, #34216, #96436, #88812, #73995, #57709, #50040, #81180, #73502, #65836 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.105474188390737791E-05, 2.168737210466838153E-05, 3.206957311019679926E-05, 4.202632042907491642E-05, 5.190279406512375961E-05, 6.156804635986610477E-05, 7.127211355680849244E-05, 8.098529113021857696E-05, 9.069011785185156942E-05, 0.0001003439242984687342, 0.0001100479914954111219, 0.0001199869562479563198, 0.0001302384145329702012, 0.0001410770161797250178, 0.0001525678786973594674, 0.0001647190599595296573 ), + .UNSPECIFIED. ) ; +#46295 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46296 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#46297 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66505, 'distance_accuracy_value', 'NONE'); +#46298 = AXIS2_PLACEMENT_3D ( 'NONE', #23822, #39124, #31974 ) ; +#46299 = DIRECTION ( 'NONE', ( 0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#46300 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46301 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000081, 0.8648700000000000276 ) ) ; +#46302 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#46303 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46304 = ADVANCED_FACE ( 'NONE', ( #18238 ), #26956, .F. ) ; +#46305 = LINE ( 'NONE', #6467, #97288 ) ; +#46306 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#46307 = STYLED_ITEM ( 'NONE', ( #54509 ), #71463 ) ; +#46308 = DIRECTION ( 'NONE', ( -0.3444045651374278427, 0.000000000000000000, -0.9388213331153585361 ) ) ; +#46309 = FACE_OUTER_BOUND ( 'NONE', #84538, .T. ) ; +#46310 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46311 = FACE_OUTER_BOUND ( 'NONE', #79096, .T. ) ; +#46312 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39868 ), #28430 ) ; +#46313 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#46314 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#46315 = SURFACE_STYLE_FILL_AREA ( #54542 ) ; +#46316 = EDGE_CURVE ( 'NONE', #79989, #8666, #3951, .T. ) ; +#46317 = ORIENTED_EDGE ( 'NONE', *, *, #51424, .T. ) ; +#46318 = FILL_AREA_STYLE_COLOUR ( '', #98323 ) ; +#46319 = LINE ( 'NONE', #25300, #48104 ) ; +#46320 = FACE_OUTER_BOUND ( 'NONE', #85301, .T. ) ; +#46321 = STYLED_ITEM ( 'NONE', ( #21964 ), #87456 ) ; +#46322 = SURFACE_SIDE_STYLE ('',( #87680 ) ) ; +#46323 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6762, 'distance_accuracy_value', 'NONE'); +#46324 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.000000000000000000 ) ) ; +#46325 = EDGE_CURVE ( 'NONE', #5115, #83217, #4443, .T. ) ; +#46326 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46328 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71732 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79148, #1036, #63359 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46327 = CARTESIAN_POINT ( 'NONE', ( 1.173595140922543800, -1.146678927717649898, 0.8099999999998975797 ) ) ; +#46329 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52855 ) ) ; +#46330 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46331 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46332 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46333 = ORIENTED_EDGE ( 'NONE', *, *, #32186, .T. ) ; +#46334 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46335 = SURFACE_STYLE_FILL_AREA ( #84165 ) ; +#46336 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#46337 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19471, 'distance_accuracy_value', 'NONE'); +#46339 = LINE ( 'NONE', #99869, #3732 ) ; +#46340 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67738, 'distance_accuracy_value', 'NONE'); +#46341 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46342 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46343 = ORIENTED_EDGE ( 'NONE', *, *, #6535, .F. ) ; +#46344 = VERTEX_POINT ( 'NONE', #90727 ) ; +#46346 = STYLED_ITEM ( 'NONE', ( #733 ), #28932 ) ; +#46345 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46347 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41517 ), #2380 ) ; +#46348 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#46349 = ORIENTED_EDGE ( 'NONE', *, *, #72388, .F. ) ; +#46350 = CARTESIAN_POINT ( 'NONE', ( -0.2130180398314890089, -1.488490865982160294, 0.8299999999999999600 ) ) ; +#46352 = LINE ( 'NONE', #31564, #84078 ) ; +#46351 = AXIS2_PLACEMENT_3D ( 'NONE', #26751, #56900, #79864 ) ; +#46353 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#46354 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46355 = EDGE_CURVE ( 'NONE', #81528, #46450, #43750, .T. ) ; +#46356 = ADVANCED_FACE ( 'NONE', ( #29449 ), #36130, .T. ) ; +#46357 = AXIS2_PLACEMENT_3D ( 'NONE', #62990, #100618, #55336 ) ; +#46358 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 4.701977403289150032E-32 ) ) ; +#46359 = PRODUCT_CONTEXT ( 'NONE', #97037, 'mechanical' ) ; +#46360 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#46362 = ORIENTED_EDGE ( 'NONE', *, *, #43450, .T. ) ; +#46361 = ORIENTED_EDGE ( 'NONE', *, *, #97034, .F. ) ; +#46363 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7162 ), #51374 ) ; +#46364 = ORIENTED_EDGE ( 'NONE', *, *, #23324, .T. ) ; +#46365 = LINE ( 'NONE', #63757, #94738 ) ; +#46366 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46367 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#46369 = FILL_AREA_STYLE ('',( #15727 ) ) ; +#46368 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46370 = VERTEX_POINT ( 'NONE', #5906 ) ; +#46371 = ORIENTED_EDGE ( 'NONE', *, *, #17095, .F. ) ; +#46372 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46373 = SURFACE_STYLE_USAGE ( .BOTH. , #93327 ) ; +#46374 = ADVANCED_FACE ( 'NONE', ( #12031 ), #21275, .F. ) ; +#46375 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46376 = AXIS2_PLACEMENT_3D ( 'NONE', #59244, #44351, #67347 ) ; +#46378 = LINE ( 'NONE', #23963, #54864 ) ; +#46377 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#46379 = ORIENTED_EDGE ( 'NONE', *, *, #29053, .F. ) ; +#46380 = VECTOR ( 'NONE', #30832, 1000.000000000000000 ) ; +#46381 = CARTESIAN_POINT ( 'NONE', ( -0.4458447660039659977, -1.054313421655699967, 0.8100000000000000533 ) ) ; +#46382 = ORIENTED_EDGE ( 'NONE', *, *, #93793, .F. ) ; +#46383 = ORIENTED_EDGE ( 'NONE', *, *, #11152, .F. ) ; +#46384 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65710, #90695, #96814, #52404 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46385 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, 0.000000000000000000 ) ) ; +#46386 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#46387 = EDGE_LOOP ( 'NONE', ( #50220, #411, #843, #100047 ) ) ; +#46388 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -1.300000000000000266, 0.000000000000000000 ) ) ; +#46389 = PLANE ( 'NONE', #12332 ) ; +#46390 = AXIS2_PLACEMENT_3D ( 'NONE', #96940, #88806, #19350 ) ; +#46391 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#46392 = ORIENTED_EDGE ( 'NONE', *, *, #3079, .F. ) ; +#46393 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#46394 = SURFACE_SIDE_STYLE ('',( #15230 ) ) ; +#46395 = ORIENTED_EDGE ( 'NONE', *, *, #85954, .F. ) ; +#46396 = ORIENTED_EDGE ( 'NONE', *, *, #47571, .F. ) ; +#46398 = LINE ( 'NONE', #55127, #61758 ) ; +#46397 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46399 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6761799387799151129, -0.02000000000000000042 ) ) ; +#46400 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90448 ) ) ; +#46401 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90449 ), #39874 ) ; +#46402 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#46403 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43149 ) ) ; +#46404 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46405 = CARTESIAN_POINT ( 'NONE', ( 0.9819563994042010968, -1.066576130479129914, 0.8299999999999997380 ) ) ; +#46406 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#46407 = ORIENTED_EDGE ( 'NONE', *, *, #62588, .T. ) ; +#46408 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#46409 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#46410 = ORIENTED_EDGE ( 'NONE', *, *, #97883, .F. ) ; +#46411 = EDGE_CURVE ( 'NONE', #79581, #4336, #91713, .T. ) ; +#46412 = SURFACE_SIDE_STYLE ('',( #78577 ) ) ; +#46414 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77918, 'distance_accuracy_value', 'NONE'); +#46413 = FACE_OUTER_BOUND ( 'NONE', #3402, .T. ) ; +#46415 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46416 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95315 ), #59547 ) ; +#46417 = AXIS2_PLACEMENT_3D ( 'NONE', #52772, #19608, #59959 ) ; +#46418 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46420 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16517 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16807, #9108, #38824 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46419 = CARTESIAN_POINT ( 'NONE', ( 1.726111644763860253, -0.9656914468017120390, 0.8100000000000000533 ) ) ; +#46421 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46422 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46423 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#46424 = SURFACE_STYLE_FILL_AREA ( #92391 ) ; +#46425 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46426 = SURFACE_SIDE_STYLE ('',( #62811 ) ) ; +#46427 = LINE ( 'NONE', #99954, #36611 ) ; +#46428 = FILL_AREA_STYLE_COLOUR ( '', #58762 ) ; +#46429 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46430 = STYLED_ITEM ( 'NONE', ( #5539 ), #97809 ) ; +#46431 = EDGE_CURVE ( 'NONE', #68821, #17366, #84077, .T. ) ; +#46433 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46432 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46434 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.3000000000000000444, 1.048695503451051965E-76 ) ) ; +#46435 = FACE_OUTER_BOUND ( 'NONE', #38089, .T. ) ; +#46436 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46437 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25663, 'distance_accuracy_value', 'NONE'); +#46438 = ORIENTED_EDGE ( 'NONE', *, *, #20548, .F. ) ; +#46439 = EDGE_CURVE ( 'NONE', #14672, #53702, #41251, .T. ) ; +#46440 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46441 = SURFACE_STYLE_FILL_AREA ( #48521 ) ; +#46442 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46443 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46444 = SURFACE_STYLE_FILL_AREA ( #14273 ) ; +#46445 = VECTOR ( 'NONE', #15364, 1000.000000000000000 ) ; +#46446 = PLANE ( 'NONE', #36699 ) ; +#46447 = VECTOR ( 'NONE', #13612, 1000.000000000000000 ) ; +#46448 = EDGE_LOOP ( 'NONE', ( #19391, #66018, #93829, #57760 ) ) ; +#46449 = STYLED_ITEM ( 'NONE', ( #96492 ), #72118 ) ; +#46450 = VERTEX_POINT ( 'NONE', #48687 ) ; +#46451 = MANIFOLD_SOLID_BREP ( 'ÊäÈë103', #63237 ) ; +#46452 = PRESENTATION_STYLE_ASSIGNMENT (( #70980 ) ) ; +#46453 = EDGE_CURVE ( 'NONE', #51489, #1339, #84562, .T. ) ; +#46454 = FILL_AREA_STYLE ('',( #7 ) ) ; +#46455 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#46456 = FILL_AREA_STYLE_COLOUR ( '', #16267 ) ; +#46457 = SURFACE_SIDE_STYLE ('',( #94443 ) ) ; +#46458 = PLANE ( 'NONE', #10875 ) ; +#46459 = STYLED_ITEM ( 'NONE', ( #26384 ), #54304 ) ; +#46460 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46461 = FACE_OUTER_BOUND ( 'NONE', #56376, .T. ) ; +#46462 = EDGE_CURVE ( 'NONE', #90736, #10764, #59545, .T. ) ; +#46463 = ORIENTED_EDGE ( 'NONE', *, *, #87961, .F. ) ; +#46464 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#46466 = VECTOR ( 'NONE', #17236, 1000.000000000000000 ) ; +#46465 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46467 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#46468 = ORIENTED_EDGE ( 'NONE', *, *, #82146, .T. ) ; +#46469 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46470 = STYLED_ITEM ( 'NONE', ( #24268 ), #88870 ) ; +#46471 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373192999999999664, 0.8648700000000000276 ) ) ; +#46472 = ORIENTED_EDGE ( 'NONE', *, *, #60884, .T. ) ; +#46473 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22083 ) ) ; +#46475 = STYLED_ITEM ( 'NONE', ( #2116 ), #26972 ) ; +#46474 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46476 = CARTESIAN_POINT ( 'NONE', ( 1.102257911893530062, -1.419390247362990021, 0.8299999999999999600 ) ) ; +#46477 = EDGE_CURVE ( 'NONE', #9892, #82715, #87977, .T. ) ; +#46478 = EDGE_CURVE ( 'NONE', #97358, #73573, #24761, .T. ) ; +#46479 = CARTESIAN_POINT ( 'NONE', ( 10.32001999999999953, 2.748280000000000278, 0.8991599999999999593 ) ) ; +#46480 = PRESENTATION_STYLE_ASSIGNMENT (( #15322 ) ) ; +#46481 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69698 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31204, #23556, #24072 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46482 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#46483 = LINE ( 'NONE', #40893, #75759 ) ; +#46485 = ORIENTED_EDGE ( 'NONE', *, *, #86445, .F. ) ; +#46484 = VERTEX_POINT ( 'NONE', #94603 ) ; +#46486 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50649, #81788, #18962, #12236 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46488 = ADVANCED_FACE ( 'NONE', ( #17996 ), #94079, .F. ) ; +#46487 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#46489 = EDGE_CURVE ( 'NONE', #69855, #64866, #95600, .T. ) ; +#46490 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46491 = ORIENTED_EDGE ( 'NONE', *, *, #2723, .F. ) ; +#46492 = AXIS2_PLACEMENT_3D ( 'NONE', #21485, #68436, #85271 ) ; +#46493 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46495 = CARTESIAN_POINT ( 'NONE', ( -0.4442493331421650260, -1.074915662348969958, 0.8100000000000000533 ) ) ; +#46494 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8199999999999999512 ) ) ; +#46496 = ORIENTED_EDGE ( 'NONE', *, *, #22179, .F. ) ; +#46497 = VERTEX_POINT ( 'NONE', #18521 ) ; +#46499 = VECTOR ( 'NONE', #50381, 1000.000000000000000 ) ; +#46498 = LINE ( 'NONE', #16347, #41650 ) ; +#46500 = EDGE_CURVE ( 'NONE', #32170, #95472, #63124, .T. ) ; +#46502 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46503 = SURFACE_STYLE_USAGE ( .BOTH. , #77160 ) ; +#46504 = VERTEX_POINT ( 'NONE', #73665 ) ; +#46505 = ORIENTED_EDGE ( 'NONE', *, *, #71404, .F. ) ; +#46506 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8648700000000000276 ) ) ; +#46507 = ORIENTED_EDGE ( 'NONE', *, *, #80510, .F. ) ; +#46508 = ADVANCED_FACE ( 'NONE', ( #42532 ), #49706, .F. ) ; +#46509 = VECTOR ( 'NONE', #2764, 1000.000000000000114 ) ; +#46510 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, -11.36999999999999922 ) ) ; +#46511 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90563 ) ) ; +#46513 = VERTEX_POINT ( 'NONE', #50224 ) ; +#46512 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#46514 = AXIS2_PLACEMENT_3D ( 'NONE', #14691, #413, #23404 ) ; +#46515 = PRESENTATION_STYLE_ASSIGNMENT (( #85327 ) ) ; +#46516 = FILL_AREA_STYLE_COLOUR ( '', #56356 ) ; +#46517 = LINE ( 'NONE', #8146, #22098 ) ; +#46518 = ORIENTED_EDGE ( 'NONE', *, *, #63122, .F. ) ; +#46519 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46520 = FILL_AREA_STYLE ('',( #85845 ) ) ; +#46521 = ORIENTED_EDGE ( 'NONE', *, *, #36961, .F. ) ; +#46522 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#46523 = FILL_AREA_STYLE_COLOUR ( '', #56313 ) ; +#46524 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16420 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19005, #33358, #72148 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46525 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#46526 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46528 = VERTEX_POINT ( 'NONE', #88989 ) ; +#46527 = FACE_OUTER_BOUND ( 'NONE', #81728, .T. ) ; +#46529 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#46530 = PRESENTATION_STYLE_ASSIGNMENT (( #15377 ) ) ; +#46531 = CARTESIAN_POINT ( 'NONE', ( -1.066288986608876721, -1.173454618603475108, 0.8099999999998604983 ) ) ; +#46532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46533 = AXIS2_PLACEMENT_3D ( 'NONE', #80122, #64276, #1992 ) ; +#46534 = FILL_AREA_STYLE_COLOUR ( '', #32654 ) ; +#46535 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#46536 = VERTEX_POINT ( 'NONE', #26217 ) ; +#46537 = ADVANCED_FACE ( 'NONE', ( #4700 ), #71035, .T. ) ; +#46538 = LINE ( 'NONE', #61904, #48500 ) ; +#46539 = LINE ( 'NONE', #16383, #33326 ) ; +#46540 = SURFACE_STYLE_FILL_AREA ( #39396 ) ; +#46541 = SURFACE_STYLE_USAGE ( .BOTH. , #52360 ) ; +#46542 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92173 ), #43499 ) ; +#46543 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46544 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#46545 = EDGE_CURVE ( 'NONE', #59976, #7257, #30685, .T. ) ; +#46546 = LINE ( 'NONE', #9195, #99625 ) ; +#46548 = STYLED_ITEM ( 'NONE', ( #44610 ), #49608 ) ; +#46547 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#46549 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#46550 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12235 ), #43295 ) ; +#46551 = SURFACE_STYLE_FILL_AREA ( #99094 ) ; +#46552 = SURFACE_STYLE_USAGE ( .BOTH. , #15397 ) ; +#46553 = ORIENTED_EDGE ( 'NONE', *, *, #58456, .F. ) ; +#46554 = VECTOR ( 'NONE', #13400, 1000.000000000000000 ) ; +#46555 = AXIS2_PLACEMENT_3D ( 'NONE', #32192, #24566, #72002 ) ; +#46556 = FILL_AREA_STYLE_COLOUR ( '', #25192 ) ; +#46557 = ORIENTED_EDGE ( 'NONE', *, *, #57033, .F. ) ; +#46559 = SURFACE_STYLE_USAGE ( .BOTH. , #69020 ) ; +#46558 = VECTOR ( 'NONE', #31077, 1000.000000000000000 ) ; +#46561 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46560 = LINE ( 'NONE', #83877, #57251 ) ; +#46562 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.05000000000000000278, 0.2100000000000000200 ) ) ; +#46563 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#46564 = FILL_AREA_STYLE_COLOUR ( '', #82264 ) ; +#46565 = VECTOR ( 'NONE', #59350, 1000.000000000000114 ) ; +#46566 = FILL_AREA_STYLE ('',( #52759 ) ) ; +#46567 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27089 ) ) ; +#46568 = ORIENTED_EDGE ( 'NONE', *, *, #78103, .F. ) ; +#46569 = CARTESIAN_POINT ( 'NONE', ( 1.733257866282789994, -0.9021709523542821296, 0.8100000000000008304 ) ) ; +#46570 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#46571 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#46573 = VECTOR ( 'NONE', #41795, 1000.000000000000000 ) ; +#46572 = LINE ( 'NONE', #15924, #69336 ) ; +#46574 = LINE ( 'NONE', #50153, #55959 ) ; +#46575 = AXIS2_PLACEMENT_3D ( 'NONE', #9724, #34330, #34830 ) ; +#46576 = LINE ( 'NONE', #7693, #38777 ) ; +#46577 = SURFACE_STYLE_FILL_AREA ( #8702 ) ; +#46578 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#46579 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#46580 = CARTESIAN_POINT ( 'NONE', ( 0.02974286737007770035, -0.9500768360162820114, 0.8299999999999999600 ) ) ; +#46581 = VECTOR ( 'NONE', #27126, 1000.000000000000000 ) ; +#46582 = SURFACE_STYLE_USAGE ( .BOTH. , #61445 ) ; +#46583 = VECTOR ( 'NONE', #100399, 1000.000000000000000 ) ; +#46584 = SURFACE_STYLE_FILL_AREA ( #15428 ) ; +#46585 = PRESENTATION_STYLE_ASSIGNMENT (( #6702 ) ) ; +#46586 = ORIENTED_EDGE ( 'NONE', *, *, #94401, .T. ) ; +#46587 = SURFACE_STYLE_FILL_AREA ( #38947 ) ; +#46588 = VERTEX_POINT ( 'NONE', #76162 ) ; +#46589 = VECTOR ( 'NONE', #92714, 1000.000000000000000 ) ; +#46590 = FILL_AREA_STYLE_COLOUR ( '', #11164 ) ; +#46591 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#46592 = CARTESIAN_POINT ( 'NONE', ( -0.9573895083907240089, -1.450479623942970253, 0.8299999999999981837 ) ) ; +#46593 = SURFACE_STYLE_FILL_AREA ( #76744 ) ; +#46594 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46595 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46596 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46597 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#46598 = EDGE_CURVE ( 'NONE', #79066, #41134, #69485, .T. ) ; +#46599 = ORIENTED_EDGE ( 'NONE', *, *, #77474, .T. ) ; +#46600 = SURFACE_SIDE_STYLE ('',( #8725 ) ) ; +#46601 = FILL_AREA_STYLE_COLOUR ( '', #100254 ) ; +#46602 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46603 = SURFACE_SIDE_STYLE ('',( #85415 ) ) ; +#46604 = ORIENTED_EDGE ( 'NONE', *, *, #81541, .T. ) ; +#46605 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2761799387799140360, 0.000000000000000000 ) ) ; +#46606 = VERTEX_POINT ( 'NONE', #22546 ) ; +#46607 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#46608 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15631, #55002, #16637 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46609 = FACE_OUTER_BOUND ( 'NONE', #25595, .T. ) ; +#46610 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38814 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76439, #66767, #74460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46611 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, -3.500000000000000444, 0.000000000000000000 ) ) ; +#46612 = SURFACE_STYLE_USAGE ( .BOTH. , #63492 ) ; +#46613 = CARTESIAN_POINT ( 'NONE', ( 8.800279041625021392, 6.264147958374939762, 0.8648700000000000276 ) ) ; +#46614 = EDGE_LOOP ( 'NONE', ( #16131, #69589, #38274, #81950 ) ) ; +#46615 = SURFACE_SIDE_STYLE ('',( #100620 ) ) ; +#46616 = EDGE_CURVE ( 'NONE', #74943, #86178, #7133, .T. ) ; +#46617 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#46618 = LINE ( 'NONE', #39473, #89957 ) ; +#46619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72736 ) ) ; +#46620 = VECTOR ( 'NONE', #25053, 1000.000000000000000 ) ; +#46621 = CIRCLE ( 'NONE', #93884, 0.009999999999999998473 ) ; +#46622 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32000 ), #67823 ) ; +#46623 = ORIENTED_EDGE ( 'NONE', *, *, #18249, .T. ) ; +#46624 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90669 ) ) ; +#46625 = PRESENTATION_STYLE_ASSIGNMENT (( #61989 ) ) ; +#46626 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#46627 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87391 ) ) ; +#46628 = ORIENTED_EDGE ( 'NONE', *, *, #70575, .T. ) ; +#46629 = ORIENTED_EDGE ( 'NONE', *, *, #4888, .T. ) ; +#46630 = PRESENTATION_STYLE_ASSIGNMENT (( #30809 ) ) ; +#46631 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_R0201_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_R0201_20210301.STEP', '', ( #88710 ) ) ; +#46632 = ORIENTED_EDGE ( 'NONE', *, *, #94415, .T. ) ; +#46633 = EDGE_CURVE ( 'NONE', #53732, #71649, #55787, .T. ) ; +#46635 = MANIFOLD_SOLID_BREP ( 'ÊäÈë2', #32312 ) ; +#46634 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43379 ), #74369 ) ; +#46636 = ORIENTED_EDGE ( 'NONE', *, *, #2696, .F. ) ; +#46638 = VERTEX_POINT ( 'NONE', #29210 ) ; +#46637 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46639 = FILL_AREA_STYLE ('',( #62001 ) ) ; +#46641 = FACE_OUTER_BOUND ( 'NONE', #99928, .T. ) ; +#46640 = LINE ( 'NONE', #21662, #6803 ) ; +#46642 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000081, 0.8991599999999999593 ) ) ; +#46643 = ORIENTED_EDGE ( 'NONE', *, *, #80417, .T. ) ; +#46644 = FILL_AREA_STYLE_COLOUR ( '', #96080 ) ; +#46645 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#46646 = SURFACE_SIDE_STYLE ('',( #15484 ) ) ; +#46647 = ORIENTED_EDGE ( 'NONE', *, *, #60037, .T. ) ; +#46648 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46649 = STYLED_ITEM ( 'NONE', ( #3238 ), #39438 ) ; +#46650 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46651 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#46652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46653 = VERTEX_POINT ( 'NONE', #6156 ) ; +#46654 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46655 = ORIENTED_EDGE ( 'NONE', *, *, #32761, .T. ) ; +#46656 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51601 ), #17287 ) ; +#46657 = EDGE_CURVE ( 'NONE', #32276, #3594, #41166, .T. ) ; +#46659 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#46658 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46660 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46661 = FILL_AREA_STYLE ('',( #15497 ) ) ; +#46662 = SURFACE_SIDE_STYLE ('',( #75809 ) ) ; +#46663 = VECTOR ( 'NONE', #32470, 1000.000000000000114 ) ; +#46664 = ORIENTED_EDGE ( 'NONE', *, *, #83592, .F. ) ; +#46665 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46666 = ORIENTED_EDGE ( 'NONE', *, *, #3593, .F. ) ; +#46667 = EDGE_CURVE ( 'NONE', #67996, #48479, #45479, .T. ) ; +#46668 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46669 = VECTOR ( 'NONE', #52118, 1000.000000000000000 ) ; +#46670 = FILL_AREA_STYLE ('',( #96028 ) ) ; +#46671 = FILL_AREA_STYLE_COLOUR ( '', #66684 ) ; +#46672 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, 0.000000000000000000 ) ) ; +#46673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46674 = ORIENTED_EDGE ( 'NONE', *, *, #24650, .T. ) ; +#46675 = CARTESIAN_POINT ( 'NONE', ( -1.284837223313930021, -1.093211113524890088, 0.8300000000000002931 ) ) ; +#46677 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17324 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59919, #37424, #6188 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46676 = LINE ( 'NONE', #54890, #4072 ) ; +#46679 = FILL_AREA_STYLE_COLOUR ( '', #8464 ) ; +#46678 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#46680 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, -13.35000000000000142 ) ) ; +#46681 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63913, 'distance_accuracy_value', 'NONE'); +#46682 = CARTESIAN_POINT ( 'NONE', ( -0.1429571421083520033, -1.443372874996269983, 0.8100000000000000533 ) ) ; +#46683 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46684 = CARTESIAN_POINT ( 'NONE', ( -1.313637677578630036, -1.335706927508150121, 0.8299999999999998490 ) ) ; +#46685 = FILL_AREA_STYLE ('',( #85501 ) ) ; +#46686 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.44219999999999970, 0.8648700000000000276 ) ) ; +#46687 = ORIENTED_EDGE ( 'NONE', *, *, #13869, .F. ) ; +#46688 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46689 = EDGE_CURVE ( 'NONE', #38134, #81528, #53198, .T. ) ; +#46690 = PLANE ( 'NONE', #65804 ) ; +#46691 = SURFACE_STYLE_FILL_AREA ( #78861 ) ; +#46692 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46693 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46694 = SURFACE_STYLE_FILL_AREA ( #38554 ) ; +#46695 = SURFACE_SIDE_STYLE ('',( #54396 ) ) ; +#46696 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999833, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#46697 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46698 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#46699 = FILL_AREA_STYLE_COLOUR ( '', #78465 ) ; +#46700 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46701 = ADVANCED_FACE ( 'NONE', ( #75183 ), #91974, .T. ) ; +#46702 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23578, #94502, #95498, #39903 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46703 = PLANE ( 'NONE', #52876 ) ; +#46704 = STYLED_ITEM ( 'NONE', ( #86698 ), #16628 ) ; +#46705 = FACE_OUTER_BOUND ( 'NONE', #35292, .T. ) ; +#46706 = VECTOR ( 'NONE', #98851, 1000.000000000000114 ) ; +#46707 = EDGE_LOOP ( 'NONE', ( #72663, #44495, #39269, #16599 ) ) ; +#46708 = SURFACE_STYLE_FILL_AREA ( #15548 ) ; +#46709 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#46710 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46712 = VECTOR ( 'NONE', #42863, 1000.000000000000000 ) ; +#46711 = PRESENTATION_STYLE_ASSIGNMENT (( #38073 ) ) ; +#46713 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46714 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#46715 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 1.149999999999999911, 0.000000000000000000 ) ) ; +#46716 = CARTESIAN_POINT ( 'NONE', ( -0.9467570119888509828, -1.236164603532529993, 0.8100000000000000533 ) ) ; +#46717 = EDGE_CURVE ( 'NONE', #5182, #34736, #555, .T. ) ; +#46718 = ORIENTED_EDGE ( 'NONE', *, *, #46970, .F. ) ; +#46719 = EDGE_CURVE ( 'NONE', #47482, #61247, #16685, .T. ) ; +#46720 = VECTOR ( 'NONE', #58967, 1000.000000000000114 ) ; +#46721 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46722 = VERTEX_POINT ( 'NONE', #46510 ) ; +#46723 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20086, #36439, #76219, #12862 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46724 = LINE ( 'NONE', #56469, #61484 ) ; +#46725 = VECTOR ( 'NONE', #85844, 1000.000000000000000 ) ; +#46726 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#46727 = FACE_OUTER_BOUND ( 'NONE', #1866, .T. ) ; +#46728 = LINE ( 'NONE', #15048, #35998 ) ; +#46729 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#46730 = ORIENTED_EDGE ( 'NONE', *, *, #27829, .F. ) ; +#46731 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#46732 = EDGE_CURVE ( 'NONE', #39862, #75533, #64380, .T. ) ; +#46733 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93046, 'distance_accuracy_value', 'NONE'); +#46734 = CARTESIAN_POINT ( 'NONE', ( -0.007147714975284390031, -1.399205570841099977, 0.8300000000000006262 ) ) ; +#46735 = ORIENTED_EDGE ( 'NONE', *, *, #40970, .T. ) ; +#46736 = SURFACE_STYLE_FILL_AREA ( #62616 ) ; +#46737 = FILL_AREA_STYLE_COLOUR ( '', #26406 ) ; +#46738 = AXIS2_PLACEMENT_3D ( 'NONE', #8998, #39720, #64219 ) ; +#46739 = ORIENTED_EDGE ( 'NONE', *, *, #4323, .T. ) ; +#46740 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#46741 = SURFACE_STYLE_FILL_AREA ( #100262 ) ; +#46742 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46743 = LINE ( 'NONE', #7877, #64513 ) ; +#46744 = EDGE_CURVE ( 'NONE', #24035, #89669, #69999, .T. ) ; +#46745 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #63267, #94097 ) ; +#46746 = PRESENTATION_STYLE_ASSIGNMENT (( #68219 ) ) ; +#46747 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82642 ) ) ; +#46748 = ORIENTED_EDGE ( 'NONE', *, *, #26028, .T. ) ; +#46749 = VECTOR ( 'NONE', #100215, 1000.000000000000114 ) ; +#46750 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36535, 'distance_accuracy_value', 'NONE'); +#46751 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46752 = SURFACE_STYLE_FILL_AREA ( #1321 ) ; +#46753 = FILL_AREA_STYLE ('',( #14083 ) ) ; +#46754 = VERTEX_POINT ( 'NONE', #9162 ) ; +#46755 = STYLED_ITEM ( 'NONE', ( #11465 ), #54961 ) ; +#46756 = LINE ( 'NONE', #69201, #83967 ) ; +#46757 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#46758 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46760 = ORIENTED_EDGE ( 'NONE', *, *, #98753, .T. ) ; +#46759 = EDGE_CURVE ( 'NONE', #11187, #61263, #86339, .T. ) ; +#46762 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46761 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46763 = VERTEX_POINT ( 'NONE', #2103 ) ; +#46764 = ORIENTED_EDGE ( 'NONE', *, *, #48900, .F. ) ; +#46765 = FILL_AREA_STYLE_COLOUR ( '', #95018 ) ; +#46766 = STYLED_ITEM ( 'NONE', ( #79947 ), #16987 ) ; +#46767 = EDGE_CURVE ( 'NONE', #32273, #74498, #16869, .T. ) ; +#46768 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46769 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46770 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89449 ), #54985 ) ; +#46771 = FILL_AREA_STYLE_COLOUR ( '', #96228 ) ; +#46772 = ORIENTED_EDGE ( 'NONE', *, *, #60248, .T. ) ; +#46773 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46774 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#46775 = VECTOR ( 'NONE', #49280, 1000.000000000000000 ) ; +#46776 = LINE ( 'NONE', #87123, #6536 ) ; +#46777 = ORIENTED_EDGE ( 'NONE', *, *, #74999, .T. ) ; +#46779 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46778 = PRESENTATION_STYLE_ASSIGNMENT (( #15103 ) ) ; +#46780 = FACE_OUTER_BOUND ( 'NONE', #77447, .T. ) ; +#46781 = EDGE_LOOP ( 'NONE', ( #7283, #16511, #18752, #17756 ) ) ; +#46782 = ORIENTED_EDGE ( 'NONE', *, *, #61324, .F. ) ; +#46783 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46784 = CLOSED_SHELL ( 'NONE', ( #51479, #62496, #19429, #95615, #93553, #73854 ) ) ; +#46785 = EDGE_CURVE ( 'NONE', #52650, #62079, #33245, .T. ) ; +#46787 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46786 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#46788 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.500000000000000000, 0.1829999999999999960 ) ) ; +#46789 = LINE ( 'NONE', #69771, #28695 ) ; +#46790 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97294 ) ) ; +#46791 = CARTESIAN_POINT ( 'NONE', ( 0.6316964285714280480, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#46792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46793 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#46794 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46795 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81034 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69449, #85800, #86820 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46796 = SURFACE_STYLE_USAGE ( .BOTH. , #70287 ) ; +#46797 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46798 = SURFACE_STYLE_FILL_AREA ( #32528 ) ; +#46799 = STYLED_ITEM ( 'NONE', ( #38270 ), #14700 ) ; +#46800 = ORIENTED_EDGE ( 'NONE', *, *, #2701, .F. ) ; +#46801 = PRESENTATION_STYLE_ASSIGNMENT (( #77966 ) ) ; +#46802 = MANIFOLD_SOLID_BREP ( 'ÊäÈë166', #7643 ) ; +#46804 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#46803 = LINE ( 'NONE', #61167, #32668 ) ; +#46805 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#46806 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46807 = LINE ( 'NONE', #38175, #25624 ) ; +#46808 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#46809 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46810 = SURFACE_SIDE_STYLE ('',( #29980 ) ) ; +#46811 = ORIENTED_EDGE ( 'NONE', *, *, #87672, .F. ) ; +#46812 = DIRECTION ( 'NONE', ( 0.7071067811865435759, 0.7071067811865514585, 0.000000000000000000 ) ) ; +#46813 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46814 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.4999999999999998890, 0.000000000000000000 ) ) ; +#46815 = PLANE ( 'NONE', #2841 ) ; +#46816 = LINE ( 'NONE', #39170, #53910 ) ; +#46817 = LINE ( 'NONE', #63199, #23577 ) ; +#46818 = PLANE ( 'NONE', #63063 ) ; +#46819 = EDGE_CURVE ( 'NONE', #37124, #15748, #55236, .T. ) ; +#46820 = EDGE_CURVE ( 'NONE', #77078, #26228, #1599, .T. ) ; +#46821 = FILL_AREA_STYLE ('',( #39174 ) ) ; +#46822 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.566666666666666652, 0.000000000000000000 ) ) ; +#46823 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30613 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8432, #23875, #39671 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46824 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#46825 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.300000000000000266, 0.000000000000000000 ) ) ; +#46826 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46827 = SURFACE_STYLE_USAGE ( .BOTH. , #15155 ) ; +#46828 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#46829 = VECTOR ( 'NONE', #63346, 1000.000000000000000 ) ; +#46830 = ADVANCED_FACE ( 'NONE', ( #17388 ), #78191, .F. ) ; +#46831 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45137 ) ) ; +#46832 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#46833 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#46834 = EDGE_CURVE ( 'NONE', #18416, #21812, #26596, .T. ) ; +#46835 = EDGE_LOOP ( 'NONE', ( #89857, #84689, #14729 ) ) ; +#46836 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2808578643762690286, -0.1399999999999999856 ) ) ; +#46837 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#46839 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46838 = VECTOR ( 'NONE', #38647, 1000.000000000000000 ) ; +#46840 = EDGE_CURVE ( 'NONE', #80438, #49021, #80225, .T. ) ; +#46841 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#46842 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#46843 = STYLED_ITEM ( 'NONE', ( #54470 ), #17089 ) ; +#46844 = CARTESIAN_POINT ( 'NONE', ( 6.106202875125043228, 9.368346875125045159, 0.8991599999999999593 ) ) ; +#46845 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46847 = ORIENTED_EDGE ( 'NONE', *, *, #96843, .T. ) ; +#46846 = VECTOR ( 'NONE', #96177, 1000.000000000000000 ) ; +#46848 = SURFACE_STYLE_FILL_AREA ( #38211 ) ; +#46849 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#46850 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#46851 = VECTOR ( 'NONE', #94670, 1000.000000000000000 ) ; +#46852 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46853 = EDGE_CURVE ( 'NONE', #84082, #100007, #18899, .T. ) ; +#46854 = FILL_AREA_STYLE ('',( #401 ) ) ; +#46855 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46856 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #40648, #9412, #21916, #32979 ), + ( #53074, #64131, #38252, #6526 ), + ( #84210, #71787, #37753, #87601 ), + ( #17629, #76042, #6029, #37268 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243633832, 0.8047378541243633832, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606864162, 0.6476030138606864162, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606864162, 0.6476030138606864162, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243633832, 0.8047378541243633832, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#46857 = CLOSED_SHELL ( 'NONE', ( #47612, #40091, #37610, #67947, #18368, #36102 ) ) ; +#46858 = ORIENTED_EDGE ( 'NONE', *, *, #93317, .F. ) ; +#46859 = ADVANCED_FACE ( 'NONE', ( #26095 ), #50592, .F. ) ; +#46860 = EDGE_LOOP ( 'NONE', ( #12161, #15874, #68775, #44649 ) ) ; +#46861 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#46862 = ORIENTED_EDGE ( 'NONE', *, *, #73849, .F. ) ; +#46863 = CARTESIAN_POINT ( 'NONE', ( -0.2710399284879780324, -1.444662699359970048, 0.8299999999999999600 ) ) ; +#46864 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86017 ) ) ; +#46865 = SURFACE_STYLE_USAGE ( .BOTH. , #100378 ) ; +#46866 = AXIS2_PLACEMENT_3D ( 'NONE', #32124, #40294, #63290 ) ; +#46867 = ADVANCED_FACE ( 'NONE', ( #27606 ), #33754, .T. ) ; +#46868 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #91832 ) ; +#46869 = SURFACE_SIDE_STYLE ('',( #69852 ) ) ; +#46870 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46871 = EDGE_CURVE ( 'NONE', #10916, #69558, #81732, .T. ) ; +#46873 = VERTEX_POINT ( 'NONE', #82227 ) ; +#46872 = EDGE_LOOP ( 'NONE', ( #49071, #25750, #43303, #81201 ) ) ; +#46874 = VECTOR ( 'NONE', #31027, 1000.000000000000000 ) ; +#46875 = VERTEX_POINT ( 'NONE', #74563 ) ; +#46876 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91644, 'distance_accuracy_value', 'NONE'); +#46877 = SURFACE_SIDE_STYLE ('',( #40768 ) ) ; +#46879 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#46878 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#46880 = ORIENTED_EDGE ( 'NONE', *, *, #6490, .F. ) ; +#46881 = PRODUCT_DEFINITION ( 'δ֪', '', #2970, #23900 ) ; +#46882 = SURFACE_STYLE_FILL_AREA ( #69865 ) ; +#46883 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#46884 = SURFACE_SIDE_STYLE ('',( #63266 ) ) ; +#46885 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46887 = VERTEX_POINT ( 'NONE', #35775 ) ; +#46886 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86046 ), #15978 ) ; +#46888 = LINE ( 'NONE', #45861, #17661 ) ; +#46889 = ORIENTED_EDGE ( 'NONE', *, *, #85684, .T. ) ; +#46890 = ORIENTED_EDGE ( 'NONE', *, *, #66323, .F. ) ; +#46891 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46892 = STYLED_ITEM ( 'NONE', ( #99232 ), #30993 ) ; +#46893 = EDGE_CURVE ( 'NONE', #31406, #31352, #66873, .T. ) ; +#46894 = FILL_AREA_STYLE ('',( #86215 ) ) ; +#46895 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8648700000000000276 ) ) ; +#46896 = FILL_AREA_STYLE ('',( #62259 ) ) ; +#46897 = ORIENTED_EDGE ( 'NONE', *, *, #76929, .F. ) ; +#46898 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#46899 = AXIS2_PLACEMENT_3D ( 'NONE', #29030, #29529, #43341 ) ; +#46900 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46901 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#46902 = ORIENTED_EDGE ( 'NONE', *, *, #67259, .T. ) ; +#46903 = SURFACE_SIDE_STYLE ('',( #8526 ) ) ; +#46904 = ORIENTED_EDGE ( 'NONE', *, *, #23865, .T. ) ; +#46905 = VERTEX_POINT ( 'NONE', #17887 ) ; +#46906 = EDGE_CURVE ( 'NONE', #70604, #59283, #39883, .T. ) ; +#46908 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#46907 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -11.41999999999999993 ) ) ; +#46909 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46910 = PLANE ( 'NONE', #49692 ) ; +#46911 = STYLED_ITEM ( 'NONE', ( #10819 ), #79541 ) ; +#46912 = ADVANCED_FACE ( 'NONE', ( #36266 ), #13693, .T. ) ; +#46913 = CARTESIAN_POINT ( 'NONE', ( 3.560618875125044269, 6.822762875125043536, 0.8648700000000000276 ) ) ; +#46914 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46915 = SURFACE_STYLE_USAGE ( .BOTH. , #91388 ) ; +#46917 = AXIS2_PLACEMENT_3D ( 'NONE', #24343, #8905, #40156 ) ; +#46916 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16920, 'distance_accuracy_value', 'NONE'); +#46918 = CARTESIAN_POINT ( 'NONE', ( 0.2295068781666219915, -0.9459922548521020325, 0.8300000000000020695 ) ) ; +#46919 = ORIENTED_EDGE ( 'NONE', *, *, #31418, .F. ) ; +#46920 = CARTESIAN_POINT ( 'NONE', ( 0.4672226176551799726, -1.085850084742399968, 0.8100000000000000533 ) ) ; +#46921 = AXIS2_PLACEMENT_3D ( 'NONE', #11224, #3154, #97051 ) ; +#46922 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#46923 = CARTESIAN_POINT ( 'NONE', ( 0.08991555325362560191, -1.292112914554750080, 0.8299999999999999600 ) ) ; +#46924 = ORIENTED_EDGE ( 'NONE', *, *, #57834, .T. ) ; +#46925 = EDGE_CURVE ( 'NONE', #42026, #4574, #59782, .T. ) ; +#46926 = DIRECTION ( 'NONE', ( -6.165170508236590408E-78, 1.306104834246980087E-31, 1.000000000000000000 ) ) ; +#46927 = FILL_AREA_STYLE ('',( #85233 ) ) ; +#46928 = VECTOR ( 'NONE', #60331, 1000.000000000000000 ) ; +#46929 = VECTOR ( 'NONE', #58732, 1000.000000000000000 ) ; +#46930 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46931 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14316 ) ) ; +#46933 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46932 = PRESENTATION_STYLE_ASSIGNMENT (( #85241 ) ) ; +#46934 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#46935 = CLOSED_SHELL ( 'NONE', ( #39102, #18122, #6776, #90733, #51568, #19304 ) ) ; +#46936 = SURFACE_SIDE_STYLE ('',( #15259 ) ) ; +#46937 = CARTESIAN_POINT ( 'NONE', ( -1.970710678118650305, 1.529289321881339925, 0.000000000000000000 ) ) ; +#46938 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37209 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36222, #5997, #52047 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46939 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#46940 = FILL_AREA_STYLE ('',( #20570 ) ) ; +#46941 = LINE ( 'NONE', #61799, #91770 ) ; +#46942 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#46943 = SURFACE_STYLE_FILL_AREA ( #15788 ) ; +#46944 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#46945 = SURFACE_SIDE_STYLE ('',( #70425 ) ) ; +#46946 = ADVANCED_FACE ( 'NONE', ( #68372 ), #5067, .T. ) ; +#46947 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#46949 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.3000000000000016542, -9.095983544939292593E-90 ) ) ; +#46948 = SURFACE_SIDE_STYLE ('',( #26901 ) ) ; +#46950 = PLANE ( 'NONE', #99381 ) ; +#46951 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#46952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46953 = VERTEX_POINT ( 'NONE', #22419 ) ; +#46954 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46955 = SURFACE_SIDE_STYLE ('',( #8072 ) ) ; +#46956 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91218 ), #11029 ) ; +#46957 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25639, 'distance_accuracy_value', 'NONE'); +#46958 = ADVANCED_FACE ( 'NONE', ( #20926 ), #53579, .T. ) ; +#46959 = VERTEX_POINT ( 'NONE', #77546 ) ; +#46960 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47044, 'distance_accuracy_value', 'NONE'); +#46961 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#46962 = CARTESIAN_POINT ( 'NONE', ( 3.822248124875013531, 4.524665124875012268, 0.8991599999999999593 ) ) ; +#46963 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46964 = EDGE_CURVE ( 'NONE', #7099, #42796, #94360, .T. ) ; +#46965 = FILL_AREA_STYLE_COLOUR ( '', #14380 ) ; +#46967 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#46966 = AXIS2_PLACEMENT_3D ( 'NONE', #27079, #89837, #83696 ) ; +#46968 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#46969 = FACE_OUTER_BOUND ( 'NONE', #37385, .T. ) ; +#46970 = EDGE_CURVE ( 'NONE', #62242, #70219, #78063, .T. ) ; +#46971 = PLANE ( 'NONE', #93693 ) ; +#46972 = AXIS2_PLACEMENT_3D ( 'NONE', #1525, #78600, #8065 ) ; +#46973 = ORIENTED_EDGE ( 'NONE', *, *, #60616, .T. ) ; +#46974 = SURFACE_SIDE_STYLE ('',( #15817 ) ) ; +#46975 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #91020, #29241, #52247, #92013 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#46976 = ORIENTED_EDGE ( 'NONE', *, *, #71949, .F. ) ; +#46977 = MANIFOLD_SOLID_BREP ( 'ÊäÈë113', #81025 ) ; +#46978 = FILL_AREA_STYLE_COLOUR ( '', #35706 ) ; +#46979 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12399, 'distance_accuracy_value', 'NONE'); +#46980 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44442, 'distance_accuracy_value', 'NONE'); +#46981 = SURFACE_STYLE_USAGE ( .BOTH. , #15819 ) ; +#46982 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15077 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19525, #35391, #44010 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#46983 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#46984 = STYLED_ITEM ( 'NONE', ( #37593 ), #84517 ) ; +#46985 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76354 ), #17606 ) ; +#46986 = CARTESIAN_POINT ( 'NONE', ( 8.277020750249976189, 1.851801249750025802, 0.8648700000000000276 ) ) ; +#46987 = LINE ( 'NONE', #23023, #32178 ) ; +#46988 = CARTESIAN_POINT ( 'NONE', ( -0.8116130133853438622, 1.464409075926969894, 0.8100000000000001643 ) ) ; +#46989 = ORIENTED_EDGE ( 'NONE', *, *, #34442, .T. ) ; +#46991 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#46990 = STYLED_ITEM ( 'NONE', ( #35093 ), #55666 ) ; +#46992 = SURFACE_STYLE_USAGE ( .BOTH. , #85795 ) ; +#46993 = ORIENTED_EDGE ( 'NONE', *, *, #45550, .F. ) ; +#46994 = EDGE_CURVE ( 'NONE', #87301, #36372, #38747, .T. ) ; +#46995 = SURFACE_SIDE_STYLE ('',( #16322 ) ) ; +#46996 = FILL_AREA_STYLE ('',( #8105 ) ) ; +#46997 = STYLED_ITEM ( 'NONE', ( #51122 ), #79964 ) ; +#46998 = ORIENTED_EDGE ( 'NONE', *, *, #18600, .F. ) ; +#46999 = CARTESIAN_POINT ( 'NONE', ( 1.205759526989409913, -1.445368494507049961, 0.8100000000000000533 ) ) ; +#47000 = SURFACE_STYLE_USAGE ( .BOTH. , #75766 ) ; +#47001 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.4245906043549200204, 0.000000000000000000 ) ) ; +#47002 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47003 = EDGE_CURVE ( 'NONE', #44242, #93361, #8515, .T. ) ; +#47004 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47005 = FACE_OUTER_BOUND ( 'NONE', #20664, .T. ) ; +#47006 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47007 = LINE ( 'NONE', #61366, #82270 ) ; +#47008 = EDGE_CURVE ( 'NONE', #68004, #55852, #57557, .T. ) ; +#47010 = ORIENTED_EDGE ( 'NONE', *, *, #4262, .F. ) ; +#47009 = ORIENTED_EDGE ( 'NONE', *, *, #37032, .F. ) ; +#47011 = VECTOR ( 'NONE', #67154, 1000.000000000000000 ) ; +#47012 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47014 = VECTOR ( 'NONE', #7850, 1000.000000000000000 ) ; +#47013 = LINE ( 'NONE', #93935, #100018 ) ; +#47015 = ORIENTED_EDGE ( 'NONE', *, *, #51524, .F. ) ; +#47016 = VECTOR ( 'NONE', #28316, 1000.000000000000000 ) ; +#47017 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#47018 = CLOSED_SHELL ( 'NONE', ( #85762, #53214, #38107, #60469, #28982, #13404 ) ) ; +#47019 = EDGE_LOOP ( 'NONE', ( #89377, #82652, #85309, #58314 ) ) ; +#47020 = VERTEX_POINT ( 'NONE', #9034 ) ; +#47021 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47022 = PLANE ( 'NONE', #74261 ) ; +#47023 = CARTESIAN_POINT ( 'NONE', ( -0.1914460425574669999, -0.9925253384799729295, 0.8300000000000000711 ) ) ; +#47024 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47025 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#47026 = EDGE_LOOP ( 'NONE', ( #81516, #33689, #81356, #32966 ) ) ; +#47027 = VERTEX_POINT ( 'NONE', #40282 ) ; +#47028 = LINE ( 'NONE', #7628, #30618 ) ; +#47029 = ORIENTED_EDGE ( 'NONE', *, *, #70836, .T. ) ; +#47030 = EDGE_CURVE ( 'NONE', #12856, #26955, #71407, .T. ) ; +#47032 = ORIENTED_EDGE ( 'NONE', *, *, #59438, .T. ) ; +#47031 = STYLED_ITEM ( 'NONE', ( #52161 ), #43971 ) ; +#47033 = FACE_OUTER_BOUND ( 'NONE', #31085, .T. ) ; +#47034 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#47035 = FILL_AREA_STYLE_COLOUR ( '', #8980 ) ; +#47036 = ORIENTED_EDGE ( 'NONE', *, *, #94530, .T. ) ; +#47037 = LINE ( 'NONE', #9672, #46725 ) ; +#47038 = LINE ( 'NONE', #15362, #52637 ) ; +#47039 = ORIENTED_EDGE ( 'NONE', *, *, #21966, .T. ) ; +#47040 = EDGE_CURVE ( 'NONE', #3989, #21763, #4599, .T. ) ; +#47041 = LINE ( 'NONE', #14347, #67660 ) ; +#47042 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #30944 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#47043 = VECTOR ( 'NONE', #60141, 1000.000000000000000 ) ; +#47044 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47045 = ADVANCED_FACE ( 'NONE', ( #41294 ), #73928, .T. ) ; +#47046 = ORIENTED_EDGE ( 'NONE', *, *, #88360, .F. ) ; +#47047 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#47049 = CARTESIAN_POINT ( 'NONE', ( 1.562899685023940055, -1.469666695271939938, 0.8299999999999999600 ) ) ; +#47048 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47050 = PRESENTATION_STYLE_ASSIGNMENT (( #7657 ) ) ; +#47051 = ORIENTED_EDGE ( 'NONE', *, *, #34242, .F. ) ; +#47052 = EDGE_CURVE ( 'NONE', #89914, #92361, #2477, .T. ) ; +#47054 = LINE ( 'NONE', #48085, #21931 ) ; +#47053 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47055 = VECTOR ( 'NONE', #28896, 1000.000000000000000 ) ; +#47056 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8099999999999852873 ) ) ; +#47057 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47058 = ADVANCED_FACE ( 'NONE', ( #25978 ), #43272, .F. ) ; +#47059 = FACE_OUTER_BOUND ( 'NONE', #52101, .T. ) ; +#47060 = SURFACE_STYLE_FILL_AREA ( #7671 ) ; +#47061 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47062 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65118 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1803, #93158, #54931 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47063 = STYLED_ITEM ( 'NONE', ( #37723 ), #5936 ) ; +#47064 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#47065 = STYLED_ITEM ( 'NONE', ( #47960 ), #80088 ) ; +#47066 = FACE_OUTER_BOUND ( 'NONE', #65923, .T. ) ; +#47067 = VERTEX_POINT ( 'NONE', #41787 ) ; +#47068 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47069 = EDGE_CURVE ( 'NONE', #22523, #58149, #17758, .T. ) ; +#47070 = EDGE_CURVE ( 'NONE', #80241, #17982, #88736, .T. ) ; +#47071 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43237 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98829, #66288, #4480 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47072 = ORIENTED_EDGE ( 'NONE', *, *, #25352, .T. ) ; +#47073 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#47074 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#47075 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#47077 = ADVANCED_FACE ( 'NONE', ( #49966 ), #50656, .F. ) ; +#47076 = SURFACE_STYLE_USAGE ( .BOTH. , #99234 ) ; +#47079 = ADVANCED_FACE ( 'NONE', ( #93206 ), #100285, .T. ) ; +#47078 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47080 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4733 ), #56975 ) ; +#47081 = LINE ( 'NONE', #9714, #51056 ) ; +#47082 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42515 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85594, #63154, #93218 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47083 = ORIENTED_EDGE ( 'NONE', *, *, #33865, .T. ) ; +#47084 = CARTESIAN_POINT ( 'NONE', ( 1.856855962848350305, -0.9758031678253591412, 0.8100000000000008304 ) ) ; +#47085 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47086 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999983624, -0.1400000000000000411 ) ) ; +#47087 = FILL_AREA_STYLE_COLOUR ( '', #36812 ) ; +#47088 = LINE ( 'NONE', #40974, #15055 ) ; +#47089 = EDGE_CURVE ( 'NONE', #96516, #92782, #1340, .T. ) ; +#47090 = SURFACE_STYLE_FILL_AREA ( #23617 ) ; +#47091 = FILL_AREA_STYLE_COLOUR ( '', #100584 ) ; +#47092 = CARTESIAN_POINT ( 'NONE', ( 10.66704099999999933, 4.241823000000000121, 0.8648700000000000276 ) ) ; +#47093 = FACE_OUTER_BOUND ( 'NONE', #60161, .T. ) ; +#47094 = EDGE_CURVE ( 'NONE', #54974, #13406, #22814, .T. ) ; +#47095 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #73315, #41672, #17638, #3362, #50363, #72803, #2863, #10922, #32990, #48337, #96748, #34529, #65634, #89127, #7723, #38467, #79283, #8239, #62473, #24689, #646, #16964, #32822, #1693, #78283, #93541, #47118, #39454, #1158, #48147, #55326, #31804, #93039, #87438 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 1, 1, 2, 2, 1, 1, 1, 1, 2, 2, 1, 1, 2, 2, 1, 1, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000149880, 0.1875000000000215938, 0.2187500000000248968, 0.2343750000000264788, 0.2500000000000280886, 0.3750000000000377476, 0.4375000000000419664, 0.4687500000000440759, 0.4843750000000451306, 0.4921875000000456857, 0.5000000000000461853, 0.5625000000000429656, 0.5937500000000414113, 0.6093750000000406342, 0.6250000000000398570, 0.6875000000000349720, 0.7187500000000318634, 0.7343750000000300870, 0.7500000000000283107, 0.8750000000000142109, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#47096 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47097 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100614, 'distance_accuracy_value', 'NONE'); +#47098 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#47099 = ORIENTED_EDGE ( 'NONE', *, *, #56285, .T. ) ; +#47100 = PRESENTATION_STYLE_ASSIGNMENT (( #47615 ) ) ; +#47101 = ORIENTED_EDGE ( 'NONE', *, *, #29444, .T. ) ; +#47102 = SURFACE_STYLE_FILL_AREA ( #8219 ) ; +#47103 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7361, 'distance_accuracy_value', 'NONE'); +#47104 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41518, 'distance_accuracy_value', 'NONE'); +#47105 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6298 ) ) ; +#47106 = FILL_AREA_STYLE ('',( #84896 ) ) ; +#47107 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#47108 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#47109 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#47110 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8991599999999999593 ) ) ; +#47111 = ORIENTED_EDGE ( 'NONE', *, *, #63020, .T. ) ; +#47112 = SURFACE_STYLE_USAGE ( .BOTH. , #15441 ) ; +#47113 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47114 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8648700000000000276 ) ) ; +#47115 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26478, 'distance_accuracy_value', 'NONE'); +#47116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47117 = ORIENTED_EDGE ( 'NONE', *, *, #18715, .T. ) ; +#47118 = CARTESIAN_POINT ( 'NONE', ( 1.277034826065559958, -1.244095395320583997, 0.8099999999998362954 ) ) ; +#47119 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6306 ) ) ; +#47120 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12500 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52966, #14088, #76411 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47121 = ORIENTED_EDGE ( 'NONE', *, *, #6954, .T. ) ; +#47122 = CARTESIAN_POINT ( 'NONE', ( 2.276179938779915091, -3.099999999999969891, 0.000000000000000000 ) ) ; +#47123 = SURFACE_STYLE_USAGE ( .BOTH. , #32827 ) ; +#47124 = VECTOR ( 'NONE', #7977, 1000.000000000000000 ) ; +#47125 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47126 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47127 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47128 = PRESENTATION_STYLE_ASSIGNMENT (( #8741 ) ) ; +#47129 = ADVANCED_FACE ( 'NONE', ( #63650 ), #62146, .F. ) ; +#47130 = VERTEX_POINT ( 'NONE', #9909 ) ; +#47131 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47132 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47133 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83040 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48272, #70713, #72233 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47134 = EDGE_CURVE ( 'NONE', #36712, #55809, #54553, .T. ) ; +#47135 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32514 ), #65082 ) ; +#47136 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79449 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37986, #38484, #22664 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47137 = ORIENTED_EDGE ( 'NONE', *, *, #71432, .T. ) ; +#47138 = AXIS2_PLACEMENT_3D ( 'NONE', #14057, #35619, #74399 ) ; +#47139 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#47140 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47141 = SURFACE_SIDE_STYLE ('',( #85439 ) ) ; +#47142 = VECTOR ( 'NONE', #103, 1000.000000000000000 ) ; +#47143 = PLANE ( 'NONE', #66738 ) ; +#47144 = FILL_AREA_STYLE_COLOUR ( '', #72131 ) ; +#47145 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.100000000000000089 ) ) ; +#47146 = EDGE_LOOP ( 'NONE', ( #39105, #98810, #16102, #44366 ) ) ; +#47147 = EDGE_LOOP ( 'NONE', ( #8571, #41680, #10248, #32867 ) ) ; +#47148 = ORIENTED_EDGE ( 'NONE', *, *, #81155, .F. ) ; +#47149 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53062 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56319, #25650, #16423 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47150 = EDGE_CURVE ( 'NONE', #64904, #33648, #9424, .T. ) ; +#47151 = ORIENTED_EDGE ( 'NONE', *, *, #69418, .T. ) ; +#47153 = VERTEX_POINT ( 'NONE', #48829 ) ; +#47152 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 4.142826999999999593, 0.8648700000000000276 ) ) ; +#47154 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83104 ) ) ; +#47155 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47156 = LINE ( 'NONE', #78319, #56947 ) ; +#47157 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47158 = VERTEX_POINT ( 'NONE', #40660 ) ; +#47159 = FILL_AREA_STYLE ('',( #46644 ) ) ; +#47160 = SURFACE_STYLE_USAGE ( .BOTH. , #15995 ) ; +#47161 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6761799387799151129, -0.02000000000000000042 ) ) ; +#47162 = ORIENTED_EDGE ( 'NONE', *, *, #89632, .F. ) ; +#47163 = EDGE_CURVE ( 'NONE', #6399, #27945, #34019, .T. ) ; +#47164 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 2.261924000000000046, 0.8648700000000000276 ) ) ; +#47165 = SURFACE_STYLE_FILL_AREA ( #54855 ) ; +#47166 = FILL_AREA_STYLE_COLOUR ( '', #2429 ) ; +#47167 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47168 = VERTEX_POINT ( 'NONE', #41167 ) ; +#47169 = SURFACE_SIDE_STYLE ('',( #86997 ) ) ; +#47170 = ORIENTED_EDGE ( 'NONE', *, *, #22690, .F. ) ; +#47172 = FILL_AREA_STYLE ('',( #87003 ) ) ; +#47171 = SURFACE_STYLE_USAGE ( .BOTH. , #22691 ) ; +#47173 = LINE ( 'NONE', #88003, #71849 ) ; +#47174 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#47175 = ADVANCED_FACE ( 'NONE', ( #80987 ), #56510, .T. ) ; +#47176 = ORIENTED_EDGE ( 'NONE', *, *, #100275, .F. ) ; +#47177 = PRESENTATION_STYLE_ASSIGNMENT (( #30845 ) ) ; +#47178 = ORIENTED_EDGE ( 'NONE', *, *, #61450, .T. ) ; +#47179 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#47180 = EDGE_CURVE ( 'NONE', #69965, #53059, #46100, .T. ) ; +#47182 = SURFACE_STYLE_USAGE ( .BOTH. , #85989 ) ; +#47181 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47183 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, 5.050936520885800324E-17, 1.000000000000000000 ) ) ; +#47184 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37477, 'distance_accuracy_value', 'NONE'); +#47185 = STYLED_ITEM ( 'NONE', ( #100599 ), #33085 ) ; +#47186 = LINE ( 'NONE', #30851, #67155 ) ; +#47187 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47188 = FACE_BOUND ( 'NONE', #80775, .T. ) ; +#47189 = EDGE_CURVE ( 'NONE', #70802, #37766, #47095, .T. ) ; +#47190 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#47191 = EDGE_CURVE ( 'NONE', #59694, #84381, #31367, .T. ) ; +#47192 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86341 ) ) ; +#47193 = ORIENTED_EDGE ( 'NONE', *, *, #60034, .T. ) ; +#47194 = CARTESIAN_POINT ( 'NONE', ( -1.102470388999849948, -1.163804091156239950, 0.8300000000000002931 ) ) ; +#47195 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47197 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.433333333333333570, 0.000000000000000000 ) ) ; +#47196 = PLANE ( 'NONE', #39886 ) ; +#47198 = LINE ( 'NONE', #78361, #70016 ) ; +#47199 = VECTOR ( 'NONE', #56757, 1000.000000000000000 ) ; +#47200 = FILL_AREA_STYLE_COLOUR ( '', #51743 ) ; +#47201 = ADVANCED_FACE ( 'NONE', ( #32319 ), #17469, .T. ) ; +#47202 = EDGE_CURVE ( 'NONE', #46754, #79041, #8731, .T. ) ; +#47203 = STYLED_ITEM ( 'NONE', ( #29428 ), #85159 ) ; +#47204 = SURFACE_STYLE_USAGE ( .BOTH. , #81777 ) ; +#47205 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.2999999999999990452, 0.1829999999999749605 ) ) ; +#47206 = FILL_AREA_STYLE ('',( #7313 ) ) ; +#47207 = VECTOR ( 'NONE', #22744, 1000.000000000000000 ) ; +#47208 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#47209 = ORIENTED_EDGE ( 'NONE', *, *, #39845, .T. ) ; +#47210 = FACE_OUTER_BOUND ( 'NONE', #44253, .T. ) ; +#47211 = AXIS2_PLACEMENT_3D ( 'NONE', #10892, #71766, #49294 ) ; +#47212 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#47213 = PLANE ( 'NONE', #5710 ) ; +#47214 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47215 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #3815, #59504, #81954, #11889, #99168, #29312, #82938, #5279, #36488, #59990, #21146, #52316, #60483, #73774, #34997, #47516, #22142, #79697, #32722 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.288220107127180975E-05, 2.546595463570696893E-05, 3.778840073839962897E-05, 5.004540205234147849E-05, 6.206962160931185320E-05, 7.376281292832417380E-05, 8.507887034544053492E-05, 9.633477727401059299E-05, 0.0001075229581203585288, 0.0001186204162254660935, 0.0001299462504990130042, 0.0001416394418180252977, 0.0001537315867160413878, 0.0001661975122778307592, 0.0001792391103226398678, 0.0001931013215793918249 ), + .UNSPECIFIED. ) ; +#47216 = EDGE_CURVE ( 'NONE', #59108, #26591, #71114, .T. ) ; +#47217 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#47218 = AXIS2_PLACEMENT_3D ( 'NONE', #86907, #15405, #16404 ) ; +#47219 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47220 = SURFACE_SIDE_STYLE ('',( #38061 ) ) ; +#47221 = FACE_OUTER_BOUND ( 'NONE', #38949, .T. ) ; +#47222 = FILL_AREA_STYLE_COLOUR ( '', #51213 ) ; +#47223 = EDGE_CURVE ( 'NONE', #80244, #91883, #75516, .T. ) ; +#47224 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47225 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 7.678360999999999770, 0.8991599999999999593 ) ) ; +#47226 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47227 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.600000000000000089, 0.000000000000000000 ) ) ; +#47228 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47229 = VECTOR ( 'NONE', #86760, 1000.000000000000000 ) ; +#47230 = AXIS2_PLACEMENT_3D ( 'NONE', #70819, #1388, #25399 ) ; +#47231 = ORIENTED_EDGE ( 'NONE', *, *, #95944, .T. ) ; +#47232 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077920276, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#47233 = ORIENTED_EDGE ( 'NONE', *, *, #30148, .F. ) ; +#47235 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11731, 'distance_accuracy_value', 'NONE'); +#47234 = VECTOR ( 'NONE', #39780, 1000.000000000000000 ) ; +#47236 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76615 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9838, #62060, #39059 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47237 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#47238 = CARTESIAN_POINT ( 'NONE', ( 0.1542778230595640010, -1.450978309596749893, 0.8299999999999999600 ) ) ; +#47239 = SURFACE_SIDE_STYLE ('',( #26298 ) ) ; +#47240 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47241 = CARTESIAN_POINT ( 'NONE', ( -1.204575085674180146, -1.140452398731560013, 0.8100000000000000533 ) ) ; +#47242 = VERTEX_POINT ( 'NONE', #48659 ) ; +#47243 = SURFACE_STYLE_USAGE ( .BOTH. , #48279 ) ; +#47244 = FILL_AREA_STYLE_COLOUR ( '', #71416 ) ; +#47245 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90349, 'distance_accuracy_value', 'NONE'); +#47246 = PLANE ( 'NONE', #75300 ) ; +#47247 = VECTOR ( 'NONE', #88294, 1000.000000000000000 ) ; +#47248 = ORIENTED_EDGE ( 'NONE', *, *, #45328, .T. ) ; +#47249 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47250 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, -1.000000000000000000, 1.498136433501504447E-75 ) ) ; +#47251 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47252 = SURFACE_SIDE_STYLE ('',( #31428 ) ) ; +#47253 = LINE ( 'NONE', #77892, #4966 ) ; +#47254 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#47255 = EDGE_LOOP ( 'NONE', ( #78190, #58627, #93333, #19715 ) ) ; +#47256 = SURFACE_STYLE_USAGE ( .BOTH. , #56974 ) ; +#47257 = AXIS2_PLACEMENT_3D ( 'NONE', #5270, #58983, #12393 ) ; +#47258 = PRESENTATION_STYLE_ASSIGNMENT (( #62611 ) ) ; +#47259 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50968, 'distance_accuracy_value', 'NONE'); +#47260 = ADVANCED_FACE ( 'NONE', ( #61967 ), #34711, .F. ) ; +#47261 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47262 = VERTEX_POINT ( 'NONE', #43838 ) ; +#47263 = FILL_AREA_STYLE ('',( #85052 ) ) ; +#47264 = AXIS2_PLACEMENT_3D ( 'NONE', #27188, #90440, #73630 ) ; +#47265 = ORIENTED_EDGE ( 'NONE', *, *, #78658, .T. ) ; +#47266 = SURFACE_STYLE_USAGE ( .BOTH. , #79944 ) ; +#47267 = LINE ( 'NONE', #57480, #59852 ) ; +#47268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47269 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96152 ) ) ; +#47270 = FILL_AREA_STYLE_COLOUR ( '', #60753 ) ; +#47271 = ORIENTED_EDGE ( 'NONE', *, *, #93107, .F. ) ; +#47272 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#47273 = VECTOR ( 'NONE', #29649, 1000.000000000000000 ) ; +#47274 = VECTOR ( 'NONE', #57389, 1000.000000000000000 ) ; +#47275 = LINE ( 'NONE', #7885, #24601 ) ; +#47277 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47276 = PLANE ( 'NONE', #75336 ) ; +#47278 = ORIENTED_EDGE ( 'NONE', *, *, #30732, .F. ) ; +#47279 = EDGE_CURVE ( 'NONE', #9359, #80711, #96429, .T. ) ; +#47280 = LINE ( 'NONE', #80461, #32012 ) ; +#47281 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#47282 = STYLED_ITEM ( 'NONE', ( #27152 ), #80574 ) ; +#47283 = VERTEX_POINT ( 'NONE', #75001 ) ; +#47284 = STYLED_ITEM ( 'NONE', ( #93996 ), #65104 ) ; +#47286 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, 3.099999999999969891, 0.000000000000000000 ) ) ; +#47285 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#47287 = VERTEX_POINT ( 'NONE', #81674 ) ; +#47288 = ORIENTED_EDGE ( 'NONE', *, *, #57985, .F. ) ; +#47289 = SURFACE_STYLE_USAGE ( .BOTH. , #71279 ) ; +#47290 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.7000000000000015099, 0.1829999999999659677 ) ) ; +#47291 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91321 ), #53856 ) ; +#47292 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999990785, -9.750000000000000000, 0.8499999999999999778 ) ) ; +#47293 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93310 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9342, #8825, #8320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47294 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#47295 = ORIENTED_EDGE ( 'NONE', *, *, #66457, .T. ) ; +#47296 = VECTOR ( 'NONE', #60137, 1000.000000000000000 ) ; +#47298 = AXIS2_PLACEMENT_3D ( 'NONE', #82401, #49242, #66550 ) ; +#47297 = FILL_AREA_STYLE_COLOUR ( '', #25466 ) ; +#47299 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.000000000000000000 ) ) ; +#47300 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#47301 = DIRECTION ( 'NONE', ( 0.7071075504167436687, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#47302 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99574, #77691, #29714, #38899, #31229, #60894, #62396, #85855, #67998, #99074, #60406, #68511, #22055, #75665, #15972, #40512, #91698, #163, #16984 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.283604389317657869E-05, 4.478221093118447146E-05, 6.621287096865519843E-05, 8.708286053616781349E-05, 0.0001074236228577684320, 0.0001271414675467374045, 0.0001466721859428506971, 0.0001659572734257127864, 0.0001851366268558053794, 0.0002043346130818376289, 0.0002236332143170337294, 0.0002432419607417113090, 0.0002635504721856831139, 0.0002848430484330285940, 0.0003074973376798180273, 0.0003314900864579890284 ), + .UNSPECIFIED. ) ; +#47303 = ORIENTED_EDGE ( 'NONE', *, *, #21728, .F. ) ; +#47304 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47305 = VERTEX_POINT ( 'NONE', #97436 ) ; +#47306 = VERTEX_POINT ( 'NONE', #58701 ) ; +#47307 = EDGE_CURVE ( 'NONE', #91646, #68052, #90298, .T. ) ; +#47308 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47309 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.700000000000000178, 1.495481557822595733E-79 ) ) ; +#47310 = PRESENTATION_STYLE_ASSIGNMENT (( #7917 ) ) ; +#47311 = FILL_AREA_STYLE_COLOUR ( '', #62807 ) ; +#47312 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77377 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4566, #22401, #55097 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47313 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#47314 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17988 ), #52300 ) ; +#47315 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#47316 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#47317 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47318 = LINE ( 'NONE', #62671, #22140 ) ; +#47319 = ORIENTED_EDGE ( 'NONE', *, *, #34492, .F. ) ; +#47320 = FILL_AREA_STYLE_COLOUR ( '', #28423 ) ; +#47322 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47321 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#47323 = VECTOR ( 'NONE', #17968, 1000.000000000000000 ) ; +#47324 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47326 = EDGE_CURVE ( 'NONE', #47933, #83048, #5008, .T. ) ; +#47325 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8099999999998962474 ) ) ; +#47327 = SURFACE_STYLE_USAGE ( .BOTH. , #42576 ) ; +#47328 = CARTESIAN_POINT ( 'NONE', ( 8.842706249749912928, 10.11080875025008829, 0.8648700000000000276 ) ) ; +#47329 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.299999999999999822, 1.084224129406308774E-78 ) ) ; +#47330 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47331 = VERTEX_POINT ( 'NONE', #74503 ) ; +#47332 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47333 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #57945, #58450, #50777, #11348, #42087, #51256, #73241, #3279, #97659, #27788, #73723, #33942, #34942, #58945, #82407, #12356, #4764, #35946, #28273 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.199810243541386873E-05, 4.278690227043494064E-05, 6.252165198475999699E-05, 8.158361054739773574E-05, 0.0001002151390316244448, 0.0001186497156152531939, 0.0001368610957251226016, 0.0001552754567345340027, 0.0001739329553027002409, 0.0001929318924837712939, 0.0002122658542286071494, 0.0002322243066156376966, 0.0002525346056374676447, 0.0002728217849409314490, 0.0002931775127340942658, 0.0003136925383507375964 ), + .UNSPECIFIED. ) ; +#47334 = SURFACE_STYLE_USAGE ( .BOTH. , #16161 ) ; +#47335 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 1.500000000000000000, 0.000000000000000000 ) ) ; +#47336 = DIRECTION ( 'NONE', ( -1.617781153285274011E-32, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#47337 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47338 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47339 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14742, 'distance_accuracy_value', 'NONE'); +#47340 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#47341 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8648700000000000276 ) ) ; +#47342 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47343 = LINE ( 'NONE', #55029, #79080 ) ; +#47344 = EDGE_CURVE ( 'NONE', #1317, #64767, #20356, .T. ) ; +#47345 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81635 ), #45615 ) ; +#47346 = AXIS2_PLACEMENT_3D ( 'NONE', #54119, #15267, #6579 ) ; +#47347 = SURFACE_STYLE_FILL_AREA ( #1905 ) ; +#47348 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47349 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47350 = SURFACE_SIDE_STYLE ('',( #70321 ) ) ; +#47351 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13019 ) ) ; +#47353 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.3000000000000013212, 0.1829999999999709637 ) ) ; +#47354 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47355 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #68422, 'design' ) ; +#47356 = STYLED_ITEM ( 'NONE', ( #17739 ), #81940 ) ; +#47357 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#47358 = SURFACE_STYLE_USAGE ( .BOTH. , #61694 ) ; +#47359 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#47360 = ORIENTED_EDGE ( 'NONE', *, *, #10702, .T. ) ; +#47361 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, 0.000000000000000000 ) ) ; +#47362 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#47363 = SURFACE_SIDE_STYLE ('',( #70330 ) ) ; +#47364 = FILL_AREA_STYLE_COLOUR ( '', #23273 ) ; +#47365 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36674, 'distance_accuracy_value', 'NONE'); +#47366 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#47367 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75726 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52893, #14016, #43194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47368 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47369 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47370 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#47371 = EDGE_CURVE ( 'NONE', #60579, #3505, #4525, .T. ) ; +#47372 = ORIENTED_EDGE ( 'NONE', *, *, #62775, .T. ) ; +#47373 = VECTOR ( 'NONE', #62948, 1000.000000000000114 ) ; +#47374 = SURFACE_STYLE_USAGE ( .BOTH. , #78022 ) ; +#47375 = STYLED_ITEM ( 'NONE', ( #78678 ), #69401 ) ; +#47376 = LINE ( 'NONE', #10474, #18721 ) ; +#47377 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.000000000000000000 ) ) ; +#47378 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47379 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50799, 'distance_accuracy_value', 'NONE'); +#47380 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56507, 'distance_accuracy_value', 'NONE'); +#47381 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47382 = ADVANCED_FACE ( 'NONE', ( #50032 ), #90816, .T. ) ; +#47383 = ORIENTED_EDGE ( 'NONE', *, *, #49240, .T. ) ; +#47384 = ORIENTED_EDGE ( 'NONE', *, *, #98141, .F. ) ; +#47385 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47386 = ORIENTED_EDGE ( 'NONE', *, *, #32808, .T. ) ; +#47387 = PLANE ( 'NONE', #37929 ) ; +#47388 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#47389 = LINE ( 'NONE', #84187, #23859 ) ; +#47390 = STYLED_ITEM ( 'NONE', ( #60084 ), #10108 ) ; +#47391 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30743, 'distance_accuracy_value', 'NONE'); +#47392 = PRESENTATION_STYLE_ASSIGNMENT (( #16209 ) ) ; +#47393 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #84088 ) ; +#47394 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47395 = FILL_AREA_STYLE ('',( #69853 ) ) ; +#47397 = EDGE_LOOP ( 'NONE', ( #43867, #59777, #19002, #100029 ) ) ; +#47396 = VERTEX_POINT ( 'NONE', #42357 ) ; +#47398 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29466 ), #34387 ) ; +#47399 = VERTEX_POINT ( 'NONE', #73498 ) ; +#47400 = SURFACE_STYLE_USAGE ( .BOTH. , #31072 ) ; +#47402 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47401 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.500000000000000000, 0.000000000000000000 ) ) ; +#47403 = ORIENTED_EDGE ( 'NONE', *, *, #40837, .T. ) ; +#47404 = EDGE_CURVE ( 'NONE', #84314, #35132, #89801, .T. ) ; +#47405 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47406 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47407 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999986226, 0.1400000000000000133 ) ) ; +#47408 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6523 ) ) ; +#47409 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38072 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15965, #70608, #7729 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47411 = FACE_OUTER_BOUND ( 'NONE', #88127, .T. ) ; +#47410 = FILL_AREA_STYLE_COLOUR ( '', #84043 ) ; +#47412 = ORIENTED_EDGE ( 'NONE', *, *, #56299, .T. ) ; +#47413 = PLANE ( 'NONE', #16049 ) ; +#47414 = EDGE_CURVE ( 'NONE', #54059, #45817, #98880, .T. ) ; +#47415 = ORIENTED_EDGE ( 'NONE', *, *, #71303, .T. ) ; +#47416 = VERTEX_POINT ( 'NONE', #45809 ) ; +#47417 = STYLED_ITEM ( 'NONE', ( #3239 ), #86498 ) ; +#47418 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50658 ), #88178 ) ; +#47419 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99497 ), #92991 ) ; +#47420 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47421 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47422 = STYLED_ITEM ( 'NONE', ( #93484 ), #58103 ) ; +#47424 = VERTEX_POINT ( 'NONE', #38199 ) ; +#47423 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#47425 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47426 = LINE ( 'NONE', #93837, #34505 ) ; +#47427 = AXIS2_PLACEMENT_3D ( 'NONE', #79351, #48226, #62540 ) ; +#47428 = FACE_OUTER_BOUND ( 'NONE', #75153, .T. ) ; +#47429 = EDGE_LOOP ( 'NONE', ( #76276, #68579, #55736, #7038 ) ) ; +#47431 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47430 = FILL_AREA_STYLE_COLOUR ( '', #36960 ) ; +#47432 = ORIENTED_EDGE ( 'NONE', *, *, #18185, .T. ) ; +#47433 = ORIENTED_EDGE ( 'NONE', *, *, #16508, .F. ) ; +#47434 = EDGE_CURVE ( 'NONE', #60158, #31808, #37214, .T. ) ; +#47436 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47435 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47437 = AXIS2_PLACEMENT_3D ( 'NONE', #100274, #40142, #23813 ) ; +#47438 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 2.000000000000000000, 0.000000000000000000 ) ) ; +#47439 = ADVANCED_FACE ( 'NONE', ( #91795 ), #22887, .T. ) ; +#47440 = CARTESIAN_POINT ( 'NONE', ( -0.4883433428992630665, -1.252526457973309970, 0.8299999999999999600 ) ) ; +#47441 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -4.591774807899559894E-33 ) ) ; +#47442 = FILL_AREA_STYLE ('',( #48974 ) ) ; +#47443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28760 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40056, #63560, #87028 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47444 = VERTEX_POINT ( 'NONE', #37701 ) ; +#47445 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47446 = CARTESIAN_POINT ( 'NONE', ( 0.08314493404879109983, -1.269147371132220314, 0.8100000000000000533 ) ) ; +#47447 = ORIENTED_EDGE ( 'NONE', *, *, #47513, .T. ) ; +#47448 = VECTOR ( 'NONE', #25596, 1000.000000000000000 ) ; +#47449 = FILL_AREA_STYLE_COLOUR ( '', #40761 ) ; +#47450 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#47452 = ADVANCED_FACE ( 'NONE', ( #6956 ), #30489, .F. ) ; +#47451 = PRESENTATION_STYLE_ASSIGNMENT (( #86762 ) ) ; +#47453 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#47454 = SURFACE_STYLE_USAGE ( .BOTH. , #69910 ) ; +#47455 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9971, 'distance_accuracy_value', 'NONE'); +#47457 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.149999999999970157, 0.000000000000000000 ) ) ; +#47458 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47459 = LINE ( 'NONE', #31634, #46038 ) ; +#47460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47461 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47462 = SURFACE_STYLE_USAGE ( .BOTH. , #2015 ) ; +#47463 = LINE ( 'NONE', #71967, #30277 ) ; +#47464 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50784 ) ) ; +#47465 = VECTOR ( 'NONE', #6174, 1000.000000000000000 ) ; +#47466 = CARTESIAN_POINT ( 'NONE', ( -0.4000000000000000222, 2.645453300864626197E-17, 0.8499999999999999778 ) ) ; +#47467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11530 ), #84987 ) ; +#47468 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75504, 'distance_accuracy_value', 'NONE'); +#47469 = SHAPE_REPRESENTATION ( 'Submodel-R0201_part_R0201', ( #42085, #35618 ), #91046 ) ; +#47470 = ORIENTED_EDGE ( 'NONE', *, *, #35353, .T. ) ; +#47471 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980549, 0.000000000000000000 ) ) ; +#47472 = VERTEX_POINT ( 'NONE', #93278 ) ; +#47473 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#47474 = FILL_AREA_STYLE_COLOUR ( '', #30308 ) ; +#47475 = STYLED_ITEM ( 'NONE', ( #27200 ), #33938 ) ; +#47476 = SURFACE_STYLE_FILL_AREA ( #33699 ) ; +#47477 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8991599999999999593 ) ) ; +#47478 = FACE_OUTER_BOUND ( 'NONE', #95227, .T. ) ; +#47479 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100960 ) ; +#47480 = AXIS2_PLACEMENT_3D ( 'NONE', #70695, #76853, #63581 ) ; +#47481 = ADVANCED_FACE ( 'NONE', ( #54019 ), #85142, .T. ) ; +#47482 = VERTEX_POINT ( 'NONE', #47361 ) ; +#47483 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#47484 = ORIENTED_EDGE ( 'NONE', *, *, #29571, .F. ) ; +#47485 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47486 = AXIS2_PLACEMENT_3D ( 'NONE', #62788, #17292, #16769 ) ; +#47487 = FILL_AREA_STYLE ('',( #23019 ) ) ; +#47488 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16479 ) ) ; +#47489 = LINE ( 'NONE', #78628, #82515 ) ; +#47490 = LINE ( 'NONE', #31169, #44467 ) ; +#47491 = VECTOR ( 'NONE', #30223, 1000.000000000000000 ) ; +#47492 = SURFACE_STYLE_FILL_AREA ( #86297 ) ; +#47493 = FILL_AREA_STYLE ('',( #53657 ) ) ; +#47494 = EDGE_LOOP ( 'NONE', ( #97097, #97956, #5949, #29247 ) ) ; +#47495 = EDGE_CURVE ( 'NONE', #12846, #5141, #17208, .T. ) ; +#47496 = LINE ( 'NONE', #78635, #63161 ) ; +#47497 = VECTOR ( 'NONE', #54845, 1000.000000000000000 ) ; +#47498 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47499 = EDGE_LOOP ( 'NONE', ( #30811, #52815, #36721, #62652 ) ) ; +#47500 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47501 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91521 ), #86650 ) ; +#47502 = AXIS2_PLACEMENT_3D ( 'NONE', #42958, #90424, #42476 ) ; +#47503 = ORIENTED_EDGE ( 'NONE', *, *, #75905, .T. ) ; +#47504 = EDGE_CURVE ( 'NONE', #38496, #25987, #20338, .T. ) ; +#47505 = CARTESIAN_POINT ( 'NONE', ( 1.039609075668130211, -1.335706927508150121, 0.8299999999999999600 ) ) ; +#47506 = SURFACE_SIDE_STYLE ('',( #49044 ) ) ; +#47507 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#47508 = CARTESIAN_POINT ( 'NONE', ( 9.391396000000000299, 10.59180000000000099, 0.8991599999999999593 ) ) ; +#47509 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47510 = LINE ( 'NONE', #78646, #70151 ) ; +#47511 = PRESENTATION_STYLE_ASSIGNMENT (( #14810 ) ) ; +#47512 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13166 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80106, #93340, #46898 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47513 = EDGE_CURVE ( 'NONE', #9281, #34599, #79526, .T. ) ; +#47515 = ORIENTED_EDGE ( 'NONE', *, *, #34057, .T. ) ; +#47514 = EDGE_LOOP ( 'NONE', ( #11293, #28821, #31717, #93061 ) ) ; +#47516 = CARTESIAN_POINT ( 'NONE', ( 1.667677657188979978, -0.9647878283071118499, 0.8099999999999994982 ) ) ; +#47517 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47518 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, 0.2999999999999991562, 0.000000000000000000 ) ) ; +#47519 = ORIENTED_EDGE ( 'NONE', *, *, #30791, .F. ) ; +#47520 = DIRECTION ( 'NONE', ( -0.6668863736986311297, 0.7451594222547881508, 0.000000000000000000 ) ) ; +#47522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47521 = FILL_AREA_STYLE ('',( #93448 ) ) ; +#47523 = ORIENTED_EDGE ( 'NONE', *, *, #40960, .F. ) ; +#47524 = ORIENTED_EDGE ( 'NONE', *, *, #53849, .T. ) ; +#47525 = CARTESIAN_POINT ( 'NONE', ( -1.416666666666666519, 3.099999999999989875, 0.000000000000000000 ) ) ; +#47526 = CARTESIAN_POINT ( 'NONE', ( 6.389045124874956905, 9.651189124874957059, 0.8648700000000000276 ) ) ; +#47527 = PLANE ( 'NONE', #98408 ) ; +#47528 = CARTESIAN_POINT ( 'NONE', ( -0.2109871940610940078, -1.020192282374009940, 0.8300000000000000711 ) ) ; +#47529 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91545 ), #45881 ) ; +#47531 = FILL_AREA_STYLE_COLOUR ( '', #87349 ) ; +#47530 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47532 = LINE ( 'NONE', #55229, #62838 ) ; +#47533 = ORIENTED_EDGE ( 'NONE', *, *, #78085, .T. ) ; +#47534 = ORIENTED_EDGE ( 'NONE', *, *, #25745, .T. ) ; +#47535 = CYLINDRICAL_SURFACE ( 'NONE', #68168, 0.009999999999999998473 ) ; +#47536 = EDGE_CURVE ( 'NONE', #4336, #62643, #7960, .T. ) ; +#47537 = ORIENTED_EDGE ( 'NONE', *, *, #46732, .F. ) ; +#47538 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#47539 = STYLED_ITEM ( 'NONE', ( #50696 ), #45744 ) ; +#47541 = ORIENTED_EDGE ( 'NONE', *, *, #48219, .T. ) ; +#47540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47542 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.05000000000000000278, 0.1900000000000000022 ) ) ; +#47543 = SURFACE_STYLE_USAGE ( .BOTH. , #62384 ) ; +#47544 = CARTESIAN_POINT ( 'NONE', ( 1.826147860666869960, -1.473933850988760064, 0.8099999999999996092 ) ) ; +#47545 = ORIENTED_EDGE ( 'NONE', *, *, #69888, .T. ) ; +#47546 = CARTESIAN_POINT ( 'NONE', ( 7.700000000000000178, 7.700000000000000178, 0.8648700000000000276 ) ) ; +#47547 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47548 = EDGE_LOOP ( 'NONE', ( #43837, #99183, #72539, #54077, #7292, #78798, #27581, #10527 ) ) ; +#47549 = ADVANCED_FACE ( 'NONE', ( #55046 ), #54038, .T. ) ; +#47550 = CARTESIAN_POINT ( 'NONE', ( -1.450000000000000178, 0.6600000000000000311, -0.8000000000000001554 ) ) ; +#47551 = EDGE_CURVE ( 'NONE', #21904, #5748, #91067, .T. ) ; +#47552 = CYLINDRICAL_SURFACE ( 'NONE', #88864, 0.8059519977764619814 ) ; +#47553 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14776 ), #29616 ) ; +#47554 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#47555 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#47557 = VERTEX_POINT ( 'NONE', #21618 ) ; +#47556 = PLANE ( 'NONE', #34695 ) ; +#47559 = CARTESIAN_POINT ( 'NONE', ( 1.594774167960719913, -1.488490865982160294, 0.8299999999999999600 ) ) ; +#47558 = CARTESIAN_POINT ( 'NONE', ( -0.4450164074857486107, -1.119265042888333506, 0.8299999999999999600 ) ) ; +#47560 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47561 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 7.282382000000000133, 0.8648700000000000276 ) ) ; +#47563 = PRESENTATION_STYLE_ASSIGNMENT (( #69511 ) ) ; +#47562 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#47564 = ORIENTED_EDGE ( 'NONE', *, *, #81851, .T. ) ; +#47565 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41654 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8381, #63126, #805 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47566 = FILL_AREA_STYLE ('',( #16382 ) ) ; +#47567 = SURFACE_STYLE_FILL_AREA ( #54230 ) ; +#47568 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65489 ), #45918 ) ; +#47569 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4600000000000000200, 0.2250000000000000333 ) ) ; +#47571 = EDGE_CURVE ( 'NONE', #94814, #36359, #91557, .T. ) ; +#47570 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47572 = SURFACE_SIDE_STYLE ('',( #10691 ) ) ; +#47574 = LINE ( 'NONE', #85358, #240 ) ; +#47573 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47575 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47576 = SURFACE_STYLE_USAGE ( .BOTH. , #9698 ) ; +#47577 = FILL_AREA_STYLE_COLOUR ( '', #97204 ) ; +#47578 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33034 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64001, #17508, #36380 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47579 = EDGE_CURVE ( 'NONE', #43123, #49721, #29286, .T. ) ; +#47580 = FILL_AREA_STYLE ('',( #71582 ) ) ; +#47581 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47582 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47583 = EDGE_LOOP ( 'NONE', ( #45419, #12258, #28084, #2578 ) ) ; +#47584 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#47585 = ORIENTED_EDGE ( 'NONE', *, *, #41802, .F. ) ; +#47586 = EDGE_CURVE ( 'NONE', #80014, #31057, #51777, .T. ) ; +#47587 = VECTOR ( 'NONE', #12378, 1000.000000000000000 ) ; +#47588 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47589 = EDGE_CURVE ( 'NONE', #19143, #69410, #4293, .T. ) ; +#47590 = FACE_OUTER_BOUND ( 'NONE', #43467, .T. ) ; +#47591 = LINE ( 'NONE', #78718, #47142 ) ; +#47592 = AXIS2_PLACEMENT_3D ( 'NONE', #92586, #14962, #53820 ) ; +#47593 = PLANE ( 'NONE', #56610 ) ; +#47594 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47595 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47596 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99663 ) ) ; +#47597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33907, 'distance_accuracy_value', 'NONE'); +#47598 = VERTEX_POINT ( 'NONE', #43092 ) ; +#47599 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.157142857142859915, 0.8299999999999999600 ) ) ; +#47600 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, -0.1400000000000000411 ) ) ; +#47601 = FACE_OUTER_BOUND ( 'NONE', #14314, .T. ) ; +#47602 = LINE ( 'NONE', #25641, #51075 ) ; +#47603 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47604 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, -0.1000000000000000056, 0.1829999999999709914 ) ) ; +#47605 = FILL_AREA_STYLE ('',( #92522 ) ) ; +#47606 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47607 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47608 = CARTESIAN_POINT ( 'NONE', ( -0.03988517032605130158, -0.9096959278232360502, 0.8299999999999999600 ) ) ; +#47609 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18279 ), #11655 ) ; +#47610 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47611 = PRESENTATION_STYLE_ASSIGNMENT (( #63947 ) ) ; +#47612 = ADVANCED_FACE ( 'NONE', ( #59963 ), #83418, .T. ) ; +#47613 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47614 = ORIENTED_EDGE ( 'NONE', *, *, #86405, .F. ) ; +#47615 = SURFACE_STYLE_USAGE ( .BOTH. , #84399 ) ; +#47616 = ORIENTED_EDGE ( 'NONE', *, *, #37338, .F. ) ; +#47617 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#47618 = LINE ( 'NONE', #37952, #78869 ) ; +#47619 = LINE ( 'NONE', #47107, #90593 ) ; +#47620 = SURFACE_SIDE_STYLE ('',( #16434 ) ) ; +#47621 = CARTESIAN_POINT ( 'NONE', ( 0.05811896311769199769, -1.438073744133560039, 0.8300000000000004041 ) ) ; +#47622 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.185754870129869909, 0.8299999999999999600 ) ) ; +#47623 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, 1.048695503451022204E-76 ) ) ; +#47624 = ORIENTED_EDGE ( 'NONE', *, *, #74135, .T. ) ; +#47625 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47626 = EDGE_CURVE ( 'NONE', #76537, #20826, #76231, .T. ) ; +#47627 = EDGE_CURVE ( 'NONE', #69166, #28663, #67073, .T. ) ; +#47628 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#47629 = SURFACE_SIDE_STYLE ('',( #33840 ) ) ; +#47630 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#47631 = ORIENTED_EDGE ( 'NONE', *, *, #78685, .T. ) ; +#47632 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47633 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85073 ) ) ; +#47634 = PLANE ( 'NONE', #66757 ) ; +#47635 = ORIENTED_EDGE ( 'NONE', *, *, #40, .F. ) ; +#47636 = EDGE_CURVE ( 'NONE', #61258, #42517, #85223, .T. ) ; +#47637 = LINE ( 'NONE', #23155, #97353 ) ; +#47638 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#47639 = STYLED_ITEM ( 'NONE', ( #2534 ), #43404 ) ; +#47640 = VECTOR ( 'NONE', #92299, 1000.000000000000000 ) ; +#47641 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#47642 = PRESENTATION_STYLE_ASSIGNMENT (( #24184 ) ) ; +#47643 = FILL_AREA_STYLE ('',( #24698 ) ) ; +#47644 = EDGE_CURVE ( 'NONE', #54871, #56074, #66573, .T. ) ; +#47645 = EDGE_LOOP ( 'NONE', ( #64857, #44402, #71150, #6519 ) ) ; +#47646 = STYLED_ITEM ( 'NONE', ( #63999 ), #59187 ) ; +#47647 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47648 = DIRECTION ( 'NONE', ( 0.7071075504167436687, 0.7071060119555145906, 0.000000000000000000 ) ) ; +#47649 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#47650 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #328 ), #81856 ) ; +#47651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85103 ) ) ; +#47652 = ORIENTED_EDGE ( 'NONE', *, *, #100037, .F. ) ; +#47653 = FILL_AREA_STYLE_COLOUR ( '', #48093 ) ; +#47654 = LINE ( 'NONE', #55348, #29960 ) ; +#47655 = SURFACE_SIDE_STYLE ('',( #16464 ) ) ; +#47656 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47657 = ORIENTED_EDGE ( 'NONE', *, *, #100449, .F. ) ; +#47658 = ORIENTED_EDGE ( 'NONE', *, *, #45818, .T. ) ; +#47659 = FILL_AREA_STYLE ('',( #32848 ) ) ; +#47660 = ADVANCED_FACE ( 'NONE', ( #97674 ), #28767, .T. ) ; +#47661 = EDGE_LOOP ( 'NONE', ( #75186, #81857, #23442, #90574 ) ) ; +#47662 = EDGE_CURVE ( 'NONE', #68882, #53546, #85908, .T. ) ; +#47663 = AXIS2_PLACEMENT_3D ( 'NONE', #62971, #8227, #638 ) ; +#47664 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47665 = EDGE_LOOP ( 'NONE', ( #97707, #40917, #82890, #6433 ) ) ; +#47667 = VERTEX_POINT ( 'NONE', #93023 ) ; +#47666 = PLANE ( 'NONE', #39471 ) ; +#47668 = PLANE ( 'NONE', #85240 ) ; +#47669 = ORIENTED_EDGE ( 'NONE', *, *, #61159, .T. ) ; +#47670 = CARTESIAN_POINT ( 'NONE', ( 1.793081130502420129, -1.407725713391660305, 0.8099999999999997202 ) ) ; +#47671 = LINE ( 'NONE', #62006, #19830 ) ; +#47672 = ORIENTED_EDGE ( 'NONE', *, *, #59662, .T. ) ; +#47673 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.000000000000000000 ) ) ; +#47674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47675 = EDGE_CURVE ( 'NONE', #73024, #58491, #39443, .T. ) ; +#47676 = SURFACE_STYLE_USAGE ( .BOTH. , #33384 ) ; +#47677 = VECTOR ( 'NONE', #58680, 1000.000000000000000 ) ; +#47678 = VERTEX_POINT ( 'NONE', #30254 ) ; +#47680 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#47679 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47681 = ORIENTED_EDGE ( 'NONE', *, *, #96826, .F. ) ; +#47683 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47682 = FACE_BOUND ( 'NONE', #98083, .T. ) ; +#47684 = PRESENTATION_STYLE_ASSIGNMENT (( #17024 ) ) ; +#47685 = STYLED_ITEM ( 'NONE', ( #66242 ), #82000 ) ; +#47686 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, -8.987602329035836718E-17, -0.6500000000000001332 ) ) ; +#47687 = SURFACE_SIDE_STYLE ('',( #72687 ) ) ; +#47688 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26506 ), #8680 ) ; +#47689 = VERTEX_POINT ( 'NONE', #53275 ) ; +#47690 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, -0.000000000000000000 ) ) ; +#47691 = SURFACE_STYLE_FILL_AREA ( #70664 ) ; +#47692 = SURFACE_STYLE_FILL_AREA ( #7296 ) ; +#47693 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47694 = AXIS2_PLACEMENT_3D ( 'NONE', #80329, #10254, #33361 ) ; +#47695 = CARTESIAN_POINT ( 'NONE', ( -0.9621292638465409608, -0.9747981717974689708, 0.8299999999999999600 ) ) ; +#47696 = LINE ( 'NONE', #32891, #21332 ) ; +#47697 = SURFACE_SIDE_STYLE ('',( #79353 ) ) ; +#47698 = AXIS2_PLACEMENT_3D ( 'NONE', #12823, #74697, #44515 ) ; +#47699 = CYLINDRICAL_SURFACE ( 'NONE', #45433, 0.09999999999999999167 ) ; +#47700 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60594 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61913, #45513, #13332 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47701 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#47702 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47703 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48512 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19619, #33967, #64087 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47704 = SURFACE_STYLE_FILL_AREA ( #31880 ) ; +#47705 = EDGE_LOOP ( 'NONE', ( #67128, #90242, #98943, #40119 ) ) ; +#47706 = CARTESIAN_POINT ( 'NONE', ( -1.067393514141900202, -1.172828961844079920, 0.8300000000000002931 ) ) ; +#47707 = PLANE ( 'NONE', #88684 ) ; +#47708 = EDGE_CURVE ( 'NONE', #25227, #28607, #77751, .T. ) ; +#47711 = SURFACE_STYLE_FILL_AREA ( #86517 ) ; +#47710 = CARTESIAN_POINT ( 'NONE', ( 1.476179938779914602, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#47709 = FACE_OUTER_BOUND ( 'NONE', #86723, .T. ) ; +#47712 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -11.36999999999999922 ) ) ; +#47713 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11673, 'distance_accuracy_value', 'NONE'); +#47714 = SURFACE_STYLE_USAGE ( .BOTH. , #87031 ) ; +#47715 = VECTOR ( 'NONE', #21843, 1000.000000000000000 ) ; +#47716 = FILL_AREA_STYLE_COLOUR ( '', #61055 ) ; +#47717 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34241, #17358, #48026, #65340, #25076, #55708 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 4 ), + ( 0.000000000000000000, 0.4999999999999997780, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#47718 = FACE_OUTER_BOUND ( 'NONE', #79251, .T. ) ; +#47719 = FACE_OUTER_BOUND ( 'NONE', #43864, .T. ) ; +#47720 = PRESENTATION_STYLE_ASSIGNMENT (( #16539 ) ) ; +#47721 = ORIENTED_EDGE ( 'NONE', *, *, #64671, .T. ) ; +#47722 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47723 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#47724 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47725 = CIRCLE ( 'NONE', #65657, 0.5799999999999999600 ) ; +#47726 = PRESENTATION_STYLE_ASSIGNMENT (( #61566 ) ) ; +#47727 = FILL_AREA_STYLE_COLOUR ( '', #75085 ) ; +#47728 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47729 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47730 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47731 = CARTESIAN_POINT ( 'NONE', ( 1.036940038338219905, -1.318596846191909977, 0.8299999999999999600 ) ) ; +#47732 = PRESENTATION_STYLE_ASSIGNMENT (( #96555 ) ) ; +#47733 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#47734 = EDGE_CURVE ( 'NONE', #36462, #13016, #47618, .T. ) ; +#47735 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#47736 = ORIENTED_EDGE ( 'NONE', *, *, #77596, .T. ) ; +#47737 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47738 = AXIS2_PLACEMENT_3D ( 'NONE', #6654, #71036, #93962 ) ; +#47739 = VERTEX_POINT ( 'NONE', #53762 ) ; +#47740 = FILL_AREA_STYLE_COLOUR ( '', #35984 ) ; +#47741 = CARTESIAN_POINT ( 'NONE', ( -0.3070726708499241231, -1.372325400170357090, 0.8099999999996897460 ) ) ; +#47742 = CARTESIAN_POINT ( 'NONE', ( 0.2039600559557959991, -1.343068553933169929, 0.8100000000000000533 ) ) ; +#47743 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47744 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.899999999999999911, 0.000000000000000000 ) ) ; +#47745 = VECTOR ( 'NONE', #94945, 1000.000000000000114 ) ; +#47746 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8100000000000000533 ) ) ; +#47747 = VERTEX_POINT ( 'NONE', #15435 ) ; +#47748 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47749 = EDGE_CURVE ( 'NONE', #59380, #56115, #62459, .T. ) ; +#47750 = SURFACE_STYLE_USAGE ( .BOTH. , #71742 ) ; +#47751 = SURFACE_STYLE_USAGE ( .BOTH. , #85538 ) ; +#47752 = VECTOR ( 'NONE', #18717, 1000.000000000000000 ) ; +#47753 = SURFACE_STYLE_FILL_AREA ( #18081 ) ; +#47754 = ORIENTED_EDGE ( 'NONE', *, *, #88249, .F. ) ; +#47755 = FACE_OUTER_BOUND ( 'NONE', #91225, .T. ) ; +#47756 = AXIS2_PLACEMENT_3D ( 'NONE', #69834, #16697, #55067 ) ; +#47757 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#47758 = SURFACE_STYLE_FILL_AREA ( #31426 ) ; +#47759 = CARTESIAN_POINT ( 'NONE', ( 2.123820061220085265, -3.099999999999969891, 0.000000000000000000 ) ) ; +#47760 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86905 ) ) ; +#47761 = LINE ( 'NONE', #23281, #99986 ) ; +#47762 = EDGE_CURVE ( 'NONE', #94098, #59301, #633, .T. ) ; +#47763 = EDGE_LOOP ( 'NONE', ( #19636, #86085, #18659, #90085 ) ) ; +#47764 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47765 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43037, 'distance_accuracy_value', 'NONE'); +#47766 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8648700000000000276 ) ) ; +#47767 = VECTOR ( 'NONE', #41204, 1000.000000000000000 ) ; +#47768 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49452 ), #16752 ) ; +#47769 = ADVANCED_FACE ( 'NONE', ( #61455 ), #8717, .T. ) ; +#47770 = PRESENTATION_STYLE_ASSIGNMENT (( #69717 ) ) ; +#47771 = ORIENTED_EDGE ( 'NONE', *, *, #65608, .T. ) ; +#47772 = VECTOR ( 'NONE', #76386, 1000.000000000000000 ) ; +#47773 = VECTOR ( 'NONE', #59932, 1000.000000000000000 ) ; +#47774 = VECTOR ( 'NONE', #19329, 1000.000000000000000 ) ; +#47775 = PRESENTATION_STYLE_ASSIGNMENT (( #16092 ) ) ; +#47776 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#47777 = ORIENTED_EDGE ( 'NONE', *, *, #29320, .F. ) ; +#47778 = LINE ( 'NONE', #63626, #55963 ) ; +#47779 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47780 = EDGE_CURVE ( 'NONE', #65417, #60579, #100113, .T. ) ; +#47781 = AXIS2_PLACEMENT_3D ( 'NONE', #46455, #53156, #67932 ) ; +#47782 = EDGE_CURVE ( 'NONE', #55952, #51323, #70070, .T. ) ; +#47783 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41244 ) ) ; +#47784 = CARTESIAN_POINT ( 'NONE', ( 0.3405668653832410464, -0.9628054983551439516, 0.8100000000000000533 ) ) ; +#47785 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76278 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18262, #93832, #39767 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47786 = ADVANCED_FACE ( 'NONE', ( #73623 ), #2677, .T. ) ; +#47787 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47788 = ORIENTED_EDGE ( 'NONE', *, *, #51126, .T. ) ; +#47789 = EDGE_CURVE ( 'NONE', #53905, #78702, #48647, .T. ) ; +#47790 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75572, 'distance_accuracy_value', 'NONE'); +#47791 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2109 ) ) ; +#47792 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#47793 = SURFACE_SIDE_STYLE ('',( #55985 ) ) ; +#47794 = ORIENTED_EDGE ( 'NONE', *, *, #8026, .F. ) ; +#47795 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#47796 = ADVANCED_FACE ( 'NONE', ( #2178 ), #26170, .T. ) ; +#47797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8560 ) ) ; +#47798 = ORIENTED_EDGE ( 'NONE', *, *, #76528, .T. ) ; +#47800 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47799 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47801 = ORIENTED_EDGE ( 'NONE', *, *, #3378, .T. ) ; +#47802 = EDGE_LOOP ( 'NONE', ( #31174, #51838, #33015, #100502 ) ) ; +#47803 = SURFACE_STYLE_FILL_AREA ( #55495 ) ; +#47804 = ADVANCED_FACE ( 'NONE', ( #24677 ), #88432, .T. ) ; +#47805 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#47806 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47807 = SURFACE_STYLE_FILL_AREA ( #23832 ) ; +#47808 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2425 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77562, #54089, #38759 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47809 = EDGE_LOOP ( 'NONE', ( #63473, #70439, #50375, #28491, #50197, #96349 ) ) ; +#47810 = FILL_AREA_STYLE ('',( #25367 ) ) ; +#47811 = LINE ( 'NONE', #46774, #71526 ) ; +#47812 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47813 = ORIENTED_EDGE ( 'NONE', *, *, #8047, .T. ) ; +#47814 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47815 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47816 = ORIENTED_EDGE ( 'NONE', *, *, #59841, .T. ) ; +#47817 = ORIENTED_EDGE ( 'NONE', *, *, #28756, .T. ) ; +#47818 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#47820 = LINE ( 'NONE', #70790, #81694 ) ; +#47819 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47821 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47822 = PLANE ( 'NONE', #88883 ) ; +#47823 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49514 ), #11870 ) ; +#47824 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47826 = VECTOR ( 'NONE', #75737, 1000.000000000000000 ) ; +#47825 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47827 = SURFACE_STYLE_USAGE ( .BOTH. , #8934 ) ; +#47828 = LINE ( 'NONE', #72304, #69876 ) ; +#47829 = FILL_AREA_STYLE ('',( #17665 ) ) ; +#47830 = ORIENTED_EDGE ( 'NONE', *, *, #23425, .T. ) ; +#47831 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78797 ), #20052 ) ; +#47832 = ADVANCED_FACE ( 'NONE', ( #44945 ), #97568, .T. ) ; +#47834 = PLANE ( 'NONE', #39455 ) ; +#47833 = FILL_AREA_STYLE ('',( #99818 ) ) ; +#47835 = LINE ( 'NONE', #24382, #37015 ) ; +#47836 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#47837 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47838 = VECTOR ( 'NONE', #14028, 1000.000000000000000 ) ; +#47839 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8648700000000000276 ) ) ; +#47840 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#47841 = EDGE_CURVE ( 'NONE', #34205, #57188, #20487, .T. ) ; +#47842 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18392, #41909, #74562, #89366 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#47843 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49534 ), #57722 ) ; +#47844 = CARTESIAN_POINT ( 'NONE', ( 1.979987608488140038, 1.411244273603041943, -11.41903816350894019 ) ) ; +#47845 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#47846 = ORIENTED_EDGE ( 'NONE', *, *, #87479, .F. ) ; +#47847 = PLANE ( 'NONE', #1624 ) ; +#47849 = AXIS2_PLACEMENT_3D ( 'NONE', #95208, #55468, #86576 ) ; +#47848 = FACE_OUTER_BOUND ( 'NONE', #27726, .T. ) ; +#47850 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #524 ) ) ; +#47851 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77197 ), #54184 ) ; +#47852 = LINE ( 'NONE', #57057, #74567 ) ; +#47853 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#47855 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47854 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78821 ) ) ; +#47856 = LINE ( 'NONE', #95791, #7000 ) ; +#47857 = AXIS2_PLACEMENT_3D ( 'NONE', #85158, #63233, #94316 ) ; +#47858 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#47859 = VECTOR ( 'NONE', #57208, 1000.000000000000000 ) ; +#47860 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#47861 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47862 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#47863 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47864 = VECTOR ( 'NONE', #18014, 1000.000000000000000 ) ; +#47865 = SURFACE_SIDE_STYLE ('',( #1406 ) ) ; +#47866 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#47867 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34845 ) ) ; +#47868 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#47869 = VECTOR ( 'NONE', #61134, 1000.000000000000000 ) ; +#47870 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.8999999999999989120, 0.1829999999999829818 ) ) ; +#47871 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, -0.01085786437626903508, -0.2500000000000000000 ) ) ; +#47872 = ORIENTED_EDGE ( 'NONE', *, *, #62588, .F. ) ; +#47873 = PRESENTATION_STYLE_ASSIGNMENT (( #48408 ) ) ; +#47874 = PRESENTATION_STYLE_ASSIGNMENT (( #16184 ) ) ; +#47875 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5501 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23157, #16448, #85927 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47877 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47876 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8648700000000000276 ) ) ; +#47878 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#47879 = CARTESIAN_POINT ( 'NONE', ( 1.151901687511581285, -0.9556482860497680365, 0.8100000000000174838 ) ) ; +#47880 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47881 = SURFACE_STYLE_FILL_AREA ( #85152 ) ; +#47882 = ORIENTED_EDGE ( 'NONE', *, *, #64448, .F. ) ; +#47883 = LINE ( 'NONE', #77001, #58667 ) ; +#47884 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34864 ), #73980 ) ; +#47885 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47886 = LINE ( 'NONE', #7978, #2146 ) ; +#47887 = AXIS2_PLACEMENT_3D ( 'NONE', #15461, #32333, #55340 ) ; +#47888 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47889 = ORIENTED_EDGE ( 'NONE', *, *, #35730, .T. ) ; +#47890 = ORIENTED_EDGE ( 'NONE', *, *, #96123, .F. ) ; +#47891 = PLANE ( 'NONE', #60167 ) ; +#47892 = VERTEX_POINT ( 'NONE', #89443 ) ; +#47893 = SURFACE_STYLE_USAGE ( .BOTH. , #87205 ) ; +#47894 = VECTOR ( 'NONE', #1677, 1000.000000000000000 ) ; +#47895 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47896 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 0.4500000000000001221 ) ) ; +#47897 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#47898 = CARTESIAN_POINT ( 'NONE', ( -1.361868870821330013, -0.9987792914302030534, 0.8299999999999997380 ) ) ; +#47899 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #48681, #82894 ) ; +#47900 = FILL_AREA_STYLE ('',( #71901 ) ) ; +#47901 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47903 = ORIENTED_EDGE ( 'NONE', *, *, #61580, .F. ) ; +#47902 = EDGE_LOOP ( 'NONE', ( #64234, #16770, #4833, #87855 ) ) ; +#47904 = VECTOR ( 'NONE', #64415, 1000.000000000000000 ) ; +#47905 = ORIENTED_EDGE ( 'NONE', *, *, #75439, .F. ) ; +#47906 = ORIENTED_EDGE ( 'NONE', *, *, #20346, .F. ) ; +#47907 = EDGE_CURVE ( 'NONE', #68118, #95335, #83975, .T. ) ; +#47908 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#47909 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33822, 'distance_accuracy_value', 'NONE'); +#47910 = CARTESIAN_POINT ( 'NONE', ( 1.702237012380340087, -1.507644428662930025, 0.8299999999999999600 ) ) ; +#47912 = SURFACE_STYLE_FILL_AREA ( #46369 ) ; +#47911 = CARTESIAN_POINT ( 'NONE', ( 0.5377516545130740511, -1.015240267636180027, 0.8299999999999999600 ) ) ; +#47913 = ORIENTED_EDGE ( 'NONE', *, *, #21591, .F. ) ; +#47914 = VECTOR ( 'NONE', #92163, 1000.000000000000000 ) ; +#47915 = FILL_AREA_STYLE_COLOUR ( '', #12320 ) ; +#47916 = PRESENTATION_STYLE_ASSIGNMENT (( #18248 ) ) ; +#47918 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#47917 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#47919 = ORIENTED_EDGE ( 'NONE', *, *, #29277, .F. ) ; +#47920 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.6999999999999990674, 5.234185452379087911E-79 ) ) ; +#47921 = VERTEX_POINT ( 'NONE', #28653 ) ; +#47922 = PRESENTATION_STYLE_ASSIGNMENT (( #80094 ) ) ; +#47923 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44611 ) ) ; +#47924 = ORIENTED_EDGE ( 'NONE', *, *, #17215, .F. ) ; +#47925 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4291 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18356, #56202, #72017 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47926 = ORIENTED_EDGE ( 'NONE', *, *, #79443, .F. ) ; +#47927 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47928 = EDGE_CURVE ( 'NONE', #74424, #11057, #27182, .T. ) ; +#47929 = AXIS2_PLACEMENT_3D ( 'NONE', #1701, #94584, #85427 ) ; +#47930 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#47931 = PRESENTATION_STYLE_ASSIGNMENT (( #8518 ) ) ; +#47933 = VERTEX_POINT ( 'NONE', #43470 ) ; +#47932 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999990785, 0.2500000000000029976, 0.8499999999999999778 ) ) ; +#47934 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47935 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#47936 = ORIENTED_EDGE ( 'NONE', *, *, #39708, .T. ) ; +#47938 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#47937 = SURFACE_STYLE_USAGE ( .BOTH. , #8022 ) ; +#47939 = ORIENTED_EDGE ( 'NONE', *, *, #18628, .F. ) ; +#47940 = ORIENTED_EDGE ( 'NONE', *, *, #50653, .T. ) ; +#47942 = CARTESIAN_POINT ( 'NONE', ( 1.313603896932107107, 0.7100000000000000755, 1.079289321881345076 ) ) ; +#47941 = FILL_AREA_STYLE ('',( #40299 ) ) ; +#47943 = CARTESIAN_POINT ( 'NONE', ( 1.817674829793840319, -1.368793146596559929, 0.8300000000000002931 ) ) ; +#47944 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40981 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28673, #29185, #37844 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47945 = CARTESIAN_POINT ( 'NONE', ( -0.4703841191077399730, -1.247659769119729978, 0.8299999999999999600 ) ) ; +#47946 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#47947 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#47948 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#47949 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52127, 'distance_accuracy_value', 'NONE'); +#47950 = EDGE_CURVE ( 'NONE', #14593, #55846, #60340, .T. ) ; +#47951 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#47952 = ORIENTED_EDGE ( 'NONE', *, *, #41961, .F. ) ; +#47953 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 0.8999999999999991340, -5.977360615245821520E-90 ) ) ; +#47954 = CARTESIAN_POINT ( 'NONE', ( 0.05990737478736290339, -1.228633653069070020, 0.8299999999999999600 ) ) ; +#47955 = VERTEX_POINT ( 'NONE', #27686 ) ; +#47956 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.000000000000000000 ) ) ; +#47957 = SURFACE_STYLE_USAGE ( .BOTH. , #55147 ) ; +#47958 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#47959 = FACE_OUTER_BOUND ( 'NONE', #51709, .T. ) ; +#47960 = PRESENTATION_STYLE_ASSIGNMENT (( #48989 ) ) ; +#47961 = EDGE_CURVE ( 'NONE', #19588, #73420, #74630, .T. ) ; +#47962 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, 3.500000000000000444, 0.000000000000000000 ) ) ; +#47963 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000533, -3.266666666666647068, 0.000000000000000000 ) ) ; +#47964 = LINE ( 'NONE', #79127, #96038 ) ; +#47965 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16686 ), #33333 ) ; +#47966 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72440 ) ) ; +#47967 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#47968 = PLANE ( 'NONE', #34335 ) ; +#47969 = PLANE ( 'NONE', #49843 ) ; +#47970 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47235 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11731, #83797, #81804 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47971 = VECTOR ( 'NONE', #97937, 1000.000000000000000 ) ; +#47972 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#47973 = VECTOR ( 'NONE', #25270, 1000.000000000000114 ) ; +#47974 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47975 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#47976 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78942 ), #95231 ) ; +#47977 = SURFACE_STYLE_FILL_AREA ( #86266 ) ; +#47978 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#47979 = VECTOR ( 'NONE', #75101, 1000.000000000000000 ) ; +#47980 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91981 ), #5515 ) ; +#47982 = ORIENTED_EDGE ( 'NONE', *, *, #58971, .F. ) ; +#47981 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40043 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3157, #18457, #65429 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47983 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#47984 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89047, 'distance_accuracy_value', 'NONE'); +#47985 = ORIENTED_EDGE ( 'NONE', *, *, #82554, .F. ) ; +#47987 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47983, 'distance_accuracy_value', 'NONE'); +#47986 = FACE_OUTER_BOUND ( 'NONE', #77519, .T. ) ; +#47988 = FILL_AREA_STYLE_COLOUR ( '', #79009 ) ; +#47989 = CARTESIAN_POINT ( 'NONE', ( 1.847806625102409894, -0.9622763341455700115, 0.8299999999999999600 ) ) ; +#47990 = AXIS2_PLACEMENT_3D ( 'NONE', #76710, #31256, #62942 ) ; +#47991 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#47992 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88729 ) ) ; +#47993 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1458578643762690197 ) ) ; +#47995 = PRESENTATION_STYLE_ASSIGNMENT (( #40351 ) ) ; +#47994 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90858 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8054, #77088, #31631 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#47996 = EDGE_CURVE ( 'NONE', #51041, #71553, #35356, .T. ) ; +#47997 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50749, #27762, #97638, #4251 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#47998 = VECTOR ( 'NONE', #58362, 1000.000000000000000 ) ; +#47999 = VECTOR ( 'NONE', #4510, 1000.000000000000000 ) ; +#48000 = VERTEX_POINT ( 'NONE', #52653 ) ; +#48001 = LINE ( 'NONE', #71483, #49135 ) ; +#48002 = EDGE_LOOP ( 'NONE', ( #74436, #33736, #19408, #84816 ) ) ; +#48003 = SURFACE_STYLE_FILL_AREA ( #39316 ) ; +#48004 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12893, 'distance_accuracy_value', 'NONE'); +#48005 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75690 ) ) ; +#48006 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#48007 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82278 ), #3981 ) ; +#48008 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48009 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.549999999999999822, 0.000000000000000000 ) ) ; +#48010 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48011 = SURFACE_STYLE_FILL_AREA ( #10102 ) ; +#48012 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13632 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33744, #33233, #42404 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48013 = ORIENTED_EDGE ( 'NONE', *, *, #93161, .F. ) ; +#48014 = EDGE_CURVE ( 'NONE', #67280, #37634, #59849, .T. ) ; +#48015 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#48016 = ADVANCED_FACE ( 'NONE', ( #19984 ), #36330, .T. ) ; +#48017 = VERTEX_POINT ( 'NONE', #78142 ) ; +#48018 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.899999999999999911, 0.1829999999999540050 ) ) ; +#48019 = DIRECTION ( 'NONE', ( -0.7071067811865469066, 0.7071067811865482389, 0.000000000000000000 ) ) ; +#48020 = ORIENTED_EDGE ( 'NONE', *, *, #17179, .F. ) ; +#48021 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48022 = SURFACE_STYLE_FILL_AREA ( #62859 ) ; +#48023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31757 ), #57908 ) ; +#48024 = FILL_AREA_STYLE ('',( #66971 ) ) ; +#48025 = PRESENTATION_STYLE_ASSIGNMENT (( #17862 ) ) ; +#48026 = CARTESIAN_POINT ( 'NONE', ( -1.214957380262011943, 2.078763679963070210, 0.8100000000000000533 ) ) ; +#48027 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.8999999999999989120, 0.8299999999999999600 ) ) ; +#48028 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48029 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.149999999999959499, 0.000000000000000000 ) ) ; +#48030 = CARTESIAN_POINT ( 'NONE', ( -0.4329969622638689120, 1.480442625815681756, 0.8100000000000000533 ) ) ; +#48033 = VERTEX_POINT ( 'NONE', #77119 ) ; +#48032 = VERTEX_POINT ( 'NONE', #21992 ) ; +#48031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47365 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36674, #97875, #59177 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48034 = FILL_AREA_STYLE_COLOUR ( '', #11076 ) ; +#48035 = PRESENTATION_STYLE_ASSIGNMENT (( #1578 ) ) ; +#48036 = VERTEX_POINT ( 'NONE', #23523 ) ; +#48037 = ADVANCED_FACE ( 'NONE', ( #8094 ), #68443, .T. ) ; +#48038 = LINE ( 'NONE', #61856, #88430 ) ; +#48039 = VECTOR ( 'NONE', #17834, 1000.000000000000000 ) ; +#48040 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57111 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92380, #37301, #83255 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48041 = SURFACE_SIDE_STYLE ('',( #16342 ) ) ; +#48042 = ORIENTED_EDGE ( 'NONE', *, *, #95779, .F. ) ; +#48043 = VERTEX_POINT ( 'NONE', #6606 ) ; +#48044 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#48045 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#48046 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28503 ), #67607 ) ; +#48047 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48048 = FACE_OUTER_BOUND ( 'NONE', #95731, .T. ) ; +#48049 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, -3.500000000000000444, 0.000000000000000000 ) ) ; +#48050 = ORIENTED_EDGE ( 'NONE', *, *, #22158, .T. ) ; +#48051 = ORIENTED_EDGE ( 'NONE', *, *, #47404, .T. ) ; +#48052 = CIRCLE ( 'NONE', #2428, 0.4690439894930241160 ) ; +#48053 = AXIS2_PLACEMENT_3D ( 'NONE', #50726, #10283, #67011 ) ; +#48054 = PRESENTATION_STYLE_ASSIGNMENT (( #16867 ) ) ; +#48055 = VERTEX_POINT ( 'NONE', #37830 ) ; +#48056 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#48057 = EDGE_CURVE ( 'NONE', #45746, #91484, #16969, .T. ) ; +#48058 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26807 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55083, #56604, #17735 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48060 = ORIENTED_EDGE ( 'NONE', *, *, #52740, .T. ) ; +#48059 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48061 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48062 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48063 = STYLED_ITEM ( 'NONE', ( #12994 ), #20106 ) ; +#48064 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48065 = ORIENTED_EDGE ( 'NONE', *, *, #55836, .F. ) ; +#48066 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93105 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43845, #43342, #27548 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48067 = VERTEX_POINT ( 'NONE', #99994 ) ; +#48068 = CARTESIAN_POINT ( 'NONE', ( -1.429289321881344943, 0.7100000000000001865, -0.9636038969321072400 ) ) ; +#48070 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62783 ), #33434 ) ; +#48069 = AXIS2_PLACEMENT_3D ( 'NONE', #48327, #80458, #79452 ) ; +#48071 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35047 ), #8829 ) ; +#48072 = SURFACE_SIDE_STYLE ('',( #72061 ) ) ; +#48073 = CARTESIAN_POINT ( 'NONE', ( 3.539405499499824082, 7.720788499499825264, 0.8991599999999999593 ) ) ; +#48074 = VECTOR ( 'NONE', #25081, 1000.000000000000000 ) ; +#48075 = PLANE ( 'NONE', #29628 ) ; +#48076 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.500000000000000000, 3.738703894556490081E-79 ) ) ; +#48078 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#48077 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#48079 = EDGE_CURVE ( 'NONE', #34599, #45808, #73145, .T. ) ; +#48080 = LINE ( 'NONE', #65386, #6605 ) ; +#48081 = PLANE ( 'NONE', #3342 ) ; +#48082 = CARTESIAN_POINT ( 'NONE', ( 2.973719124875012554, 5.373193124875012217, 0.8648700000000000276 ) ) ; +#48083 = ORIENTED_EDGE ( 'NONE', *, *, #78642, .F. ) ; +#48084 = FILL_AREA_STYLE_COLOUR ( '', #77766 ) ; +#48085 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#48087 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95339 ), #51377 ) ; +#48086 = LINE ( 'NONE', #62919, #75666 ) ; +#48088 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4784314575050762630, 0.2458578643762690252 ) ) ; +#48089 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48090 = SURFACE_STYLE_USAGE ( .BOTH. , #78228 ) ; +#48091 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.900000000000000133, -1.507334416018511324E-89 ) ) ; +#48092 = ADVANCED_FACE ( 'NONE', ( #69435 ), #15297, .T. ) ; +#48093 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48094 = PLANE ( 'NONE', #5235 ) ; +#48095 = ORIENTED_EDGE ( 'NONE', *, *, #82762, .F. ) ; +#48096 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#48097 = SURFACE_STYLE_FILL_AREA ( #38422 ) ; +#48098 = ORIENTED_EDGE ( 'NONE', *, *, #10565, .F. ) ; +#48099 = LINE ( 'NONE', #79242, #52088 ) ; +#48100 = VECTOR ( 'NONE', #17194, 1000.000000000000000 ) ; +#48101 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48102 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.000000000000000000 ) ) ; +#48103 = LINE ( 'NONE', #10190, #47999 ) ; +#48104 = VECTOR ( 'NONE', #64081, 1000.000000000000000 ) ; +#48105 = AXIS2_PLACEMENT_3D ( 'NONE', #82253, #25616, #41442 ) ; +#48106 = ORIENTED_EDGE ( 'NONE', *, *, #61663, .F. ) ; +#48107 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#48108 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#48109 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8648700000000000276 ) ) ; +#48110 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48111 = AXIS2_PLACEMENT_3D ( 'NONE', #19406, #40912, #79712 ) ; +#48112 = SURFACE_STYLE_USAGE ( .BOTH. , #86920 ) ; +#48113 = LINE ( 'NONE', #55295, #27021 ) ; +#48114 = VECTOR ( 'NONE', #91718, 1000.000000000000000 ) ; +#48115 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44870 ) ) ; +#48116 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33423 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55249, #38891, #32250 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48117 = CARTESIAN_POINT ( 'NONE', ( 0.06997596596441089944, -1.057175192472970204, 0.8299999999999999600 ) ) ; +#48118 = EDGE_CURVE ( 'NONE', #61785, #96849, #18307, .T. ) ; +#48119 = ADVANCED_FACE ( 'NONE', ( #95942, #71996 ), #40867, .F. ) ; +#48120 = SURFACE_SIDE_STYLE ('',( #94545 ) ) ; +#48121 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59403, 'distance_accuracy_value', 'NONE'); +#48122 = SURFACE_STYLE_FILL_AREA ( #39436 ) ; +#48123 = VECTOR ( 'NONE', #88979, 1000.000000000000000 ) ; +#48124 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8648700000000000276 ) ) ; +#48125 = ORIENTED_EDGE ( 'NONE', *, *, #65088, .F. ) ; +#48126 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 8.979438000000001807, 0.8648700000000000276 ) ) ; +#48127 = VERTEX_POINT ( 'NONE', #57203 ) ; +#48128 = SURFACE_SIDE_STYLE ('',( #31784 ) ) ; +#48129 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62798, 'distance_accuracy_value', 'NONE'); +#48130 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3226, 'distance_accuracy_value', 'NONE'); +#48131 = SURFACE_STYLE_USAGE ( .BOTH. , #25178 ) ; +#48132 = FACE_OUTER_BOUND ( 'NONE', #68145, .T. ) ; +#48133 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#48134 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17290 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98143, #34956, #28285 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48135 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48136 = LINE ( 'NONE', #71622, #63095 ) ; +#48137 = VECTOR ( 'NONE', #8985, 1000.000000000000000 ) ; +#48138 = VERTEX_POINT ( 'NONE', #3050 ) ; +#48139 = CARTESIAN_POINT ( 'NONE', ( 1.892524908602200018, -1.389761831846570095, 0.8300000000000011813 ) ) ; +#48140 = EDGE_CURVE ( 'NONE', #95096, #58037, #33192, .T. ) ; +#48141 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48142 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25860, 'distance_accuracy_value', 'NONE'); +#48143 = EDGE_CURVE ( 'NONE', #67581, #95260, #64330, .T. ) ; +#48145 = AXIS2_PLACEMENT_3D ( 'NONE', #34544, #72819, #17157 ) ; +#48144 = VECTOR ( 'NONE', #100531, 1000.000000000000000 ) ; +#48146 = ORIENTED_EDGE ( 'NONE', *, *, #47495, .T. ) ; +#48147 = CARTESIAN_POINT ( 'NONE', ( 1.307463592336401970, -1.254699690856928784, 0.8099999999998299671 ) ) ; +#48148 = ORIENTED_EDGE ( 'NONE', *, *, #80221, .F. ) ; +#48149 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#48150 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76101 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3893, #51868, #53354 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48151 = SURFACE_STYLE_USAGE ( .BOTH. , #73146 ) ; +#48152 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#48153 = FILL_AREA_STYLE_COLOUR ( '', #77504 ) ; +#48154 = PLANE ( 'NONE', #46357 ) ; +#48155 = ORIENTED_EDGE ( 'NONE', *, *, #76271, .F. ) ; +#48156 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56269 ), #66084 ) ; +#48157 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#48158 = ORIENTED_EDGE ( 'NONE', *, *, #58629, .F. ) ; +#48160 = ADVANCED_FACE ( 'NONE', ( #65325 ), #18341, .T. ) ; +#48159 = AXIS2_PLACEMENT_3D ( 'NONE', #61782, #22967, #13207 ) ; +#48161 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48162 = PRESENTATION_STYLE_ASSIGNMENT (( #70616 ) ) ; +#48163 = ORIENTED_EDGE ( 'NONE', *, *, #69594, .F. ) ; +#48164 = EDGE_CURVE ( 'NONE', #28482, #88940, #27055, .T. ) ; +#48165 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#48166 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#48167 = AXIS2_PLACEMENT_3D ( 'NONE', #44, #7623, #69476 ) ; +#48168 = SURFACE_SIDE_STYLE ('',( #9768 ) ) ; +#48169 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48170 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#48171 = VERTEX_POINT ( 'NONE', #98896 ) ; +#48174 = ORIENTED_EDGE ( 'NONE', *, *, #62876, .F. ) ; +#48173 = EDGE_LOOP ( 'NONE', ( #37014, #69696, #12038, #11032 ) ) ; +#48172 = VECTOR ( 'NONE', #68756, 1000.000000000000000 ) ; +#48175 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48176 = VERTEX_POINT ( 'NONE', #67327 ) ; +#48177 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#48178 = EDGE_CURVE ( 'NONE', #5265, #64618, #58218, .T. ) ; +#48179 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48180 = EDGE_CURVE ( 'NONE', #83440, #83324, #31715, .T. ) ; +#48181 = ORIENTED_EDGE ( 'NONE', *, *, #3880, .F. ) ; +#48182 = VERTEX_POINT ( 'NONE', #28062 ) ; +#48183 = VECTOR ( 'NONE', #64263, 1000.000000000000000 ) ; +#48184 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 5.551115123125790098E-17 ) ) ; +#48185 = CIRCLE ( 'NONE', #4149, 0.1000000000000000472 ) ; +#48187 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48186 = PRESENTATION_STYLE_ASSIGNMENT (( #95606 ) ) ; +#48188 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20393 ), #93747 ) ; +#48189 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48190 = ORIENTED_EDGE ( 'NONE', *, *, #95454, .T. ) ; +#48191 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8648700000000000276 ) ) ; +#48192 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000006176, -0.1400000000000000411 ) ) ; +#48193 = FILL_AREA_STYLE ('',( #85458 ) ) ; +#48194 = EDGE_LOOP ( 'NONE', ( #49749, #76071, #63386, #99189 ) ) ; +#48195 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #69427 ) ) ; +#48196 = DIRECTION ( 'NONE', ( 0.7071067806865475314, -0.7071067816865476141, 0.000000000000000000 ) ) ; +#48197 = STYLED_ITEM ( 'NONE', ( #6883 ), #82699 ) ; +#48198 = FILL_AREA_STYLE ('',( #24741 ) ) ; +#48199 = FACE_OUTER_BOUND ( 'NONE', #87222, .T. ) ; +#48200 = EDGE_LOOP ( 'NONE', ( #9988, #52833, #97335, #18486 ) ) ; +#48202 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48201 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26997 ), #53076 ) ; +#48203 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61260 ) ) ; +#48204 = VERTEX_POINT ( 'NONE', #50550 ) ; +#48205 = AXIS2_PLACEMENT_3D ( 'NONE', #99509, #51164, #90437 ) ; +#48206 = SURFACE_SIDE_STYLE ('',( #17021 ) ) ; +#48207 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#48208 = ADVANCED_FACE ( 'NONE', ( #29043 ), #66833, .T. ) ; +#48209 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48210 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2850000000000000311, 0.000000000000000000 ) ) ; +#48211 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48212 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #28235, #27247, #35421, #52236 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48213 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.000000000000000000 ) ) ; +#48214 = ORIENTED_EDGE ( 'NONE', *, *, #52211, .T. ) ; +#48215 = STYLED_ITEM ( 'NONE', ( #22364 ), #22470 ) ; +#48217 = SURFACE_SIDE_STYLE ('',( #17033 ) ) ; +#48216 = SURFACE_STYLE_USAGE ( .BOTH. , #56898 ) ; +#48218 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48219 = EDGE_CURVE ( 'NONE', #39129, #91380, #59226, .T. ) ; +#48220 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48222 = VECTOR ( 'NONE', #51631, 1000.000000000000000 ) ; +#48221 = VECTOR ( 'NONE', #18401, 1000.000000000000000 ) ; +#48223 = VECTOR ( 'NONE', #29270, 1000.000000000000000 ) ; +#48224 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47888, 'distance_accuracy_value', 'NONE'); +#48225 = CARTESIAN_POINT ( 'NONE', ( -0.9730827514092390551, -0.9588323859052130249, 0.8100000000000000533 ) ) ; +#48227 = EDGE_CURVE ( 'NONE', #79525, #25465, #90314, .T. ) ; +#48226 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#48228 = FACE_BOUND ( 'NONE', #90507, .T. ) ; +#48229 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58094 ), #40133 ) ; +#48230 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#48231 = PRESENTATION_STYLE_ASSIGNMENT (( #71181 ) ) ; +#48232 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999999778, -3.123820061220055511, 0.000000000000000000 ) ) ; +#48233 = ORIENTED_EDGE ( 'NONE', *, *, #13198, .T. ) ; +#48234 = LINE ( 'NONE', #72201, #25315 ) ; +#48237 = SURFACE_SIDE_STYLE ('',( #47711 ) ) ; +#48236 = FACE_OUTER_BOUND ( 'NONE', #93786, .T. ) ; +#48235 = SURFACE_STYLE_FILL_AREA ( #49233 ) ; +#48238 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#48239 = LINE ( 'NONE', #70683, #81202 ) ; +#48240 = CARTESIAN_POINT ( 'NONE', ( 0.3189951478977410271, -1.329088006532930022, 0.8299999999999999600 ) ) ; +#48241 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72637 ), #41678 ) ; +#48242 = PLANE ( 'NONE', #63351 ) ; +#48243 = PRESENTATION_STYLE_ASSIGNMENT (( #33428 ) ) ; +#48244 = ORIENTED_EDGE ( 'NONE', *, *, #36918, .T. ) ; +#48245 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48246 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#48247 = CARTESIAN_POINT ( 'NONE', ( 8.404299750249974110, 10.54921475024997868, 0.8991599999999999593 ) ) ; +#48248 = DIRECTION ( 'NONE', ( -0.7071045084557385785, 0.7071090539100516326, 0.000000000000000000 ) ) ; +#48249 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48250 = LINE ( 'NONE', #62065, #20775 ) ; +#48251 = PRESENTATION_STYLE_ASSIGNMENT (( #23750 ) ) ; +#48252 = PLANE ( 'NONE', #39312 ) ; +#48253 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92305 ), #80911 ) ; +#48254 = FACE_OUTER_BOUND ( 'NONE', #18630, .T. ) ; +#48255 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48256 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48257 = SURFACE_STYLE_FILL_AREA ( #39567 ) ; +#48258 = ADVANCED_FACE ( 'NONE', ( #12647 ), #13133, .T. ) ; +#48259 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#48260 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48261 = SURFACE_SIDE_STYLE ('',( #16554 ) ) ; +#48262 = LINE ( 'NONE', #55429, #68392 ) ; +#48263 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#48264 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#48265 = ORIENTED_EDGE ( 'NONE', *, *, #49055, .T. ) ; +#48266 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#48267 = ORIENTED_EDGE ( 'NONE', *, *, #14670, .F. ) ; +#48268 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55810, 'distance_accuracy_value', 'NONE'); +#48269 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48270 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92238 ), #69408 ) ; +#48271 = VECTOR ( 'NONE', #96953, 1000.000000000000000 ) ; +#48272 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48273 = STYLED_ITEM ( 'NONE', ( #34812 ), #54495 ) ; +#48274 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48275 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48276 = PRESENTATION_STYLE_ASSIGNMENT (( #56457 ) ) ; +#48277 = CARTESIAN_POINT ( 'NONE', ( -1.188831266068800074, -1.144973971495400145, 0.8299999999999999600 ) ) ; +#48278 = ORIENTED_EDGE ( 'NONE', *, *, #57715, .T. ) ; +#48279 = SURFACE_SIDE_STYLE ('',( #71228 ) ) ; +#48280 = VECTOR ( 'NONE', #64499, 1000.000000000000114 ) ; +#48281 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48282 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27884, 'distance_accuracy_value', 'NONE'); +#48283 = VECTOR ( 'NONE', #5813, 1000.000000000000114 ) ; +#48285 = EDGE_CURVE ( 'NONE', #54091, #86708, #61712, .T. ) ; +#48284 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61325 ), #61164 ) ; +#48287 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#48286 = VECTOR ( 'NONE', #66333, 1000.000000000000000 ) ; +#48288 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#48289 = CIRCLE ( 'NONE', #40108, 0.009999999999999998473 ) ; +#48290 = VERTEX_POINT ( 'NONE', #93294 ) ; +#48291 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48292 = EDGE_CURVE ( 'NONE', #90356, #100648, #48052, .T. ) ; +#48293 = PRESENTATION_STYLE_ASSIGNMENT (( #55946 ) ) ; +#48294 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48295 = STYLED_ITEM ( 'NONE', ( #86201 ), #77622 ) ; +#48296 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.000000000000000000 ) ) ; +#48297 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#48298 = CIRCLE ( 'NONE', #84118, 0.6499999999789451977 ) ; +#48299 = ORIENTED_EDGE ( 'NONE', *, *, #15151, .F. ) ; +#48300 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#48301 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#48302 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28486, 'distance_accuracy_value', 'NONE'); +#48303 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#48304 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53158 ), #100322 ) ; +#48305 = SURFACE_STYLE_USAGE ( .BOTH. , #71244 ) ; +#48306 = PLANE ( 'NONE', #41938 ) ; +#48307 = ORIENTED_EDGE ( 'NONE', *, *, #37601, .T. ) ; +#48308 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48309 = ADVANCED_FACE ( 'NONE', ( #5990 ), #54034, .T. ) ; +#48310 = VECTOR ( 'NONE', #78617, 1000.000000000000000 ) ; +#48311 = FACE_OUTER_BOUND ( 'NONE', #59749, .T. ) ; +#48312 = ORIENTED_EDGE ( 'NONE', *, *, #24754, .T. ) ; +#48313 = FILL_AREA_STYLE ('',( #86062 ) ) ; +#48314 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.000000000000000000 ) ) ; +#48315 = FILL_AREA_STYLE_COLOUR ( '', #85739 ) ; +#48316 = PRESENTATION_STYLE_ASSIGNMENT (( #33487 ) ) ; +#48317 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#48318 = VECTOR ( 'NONE', #46331, 1000.000000000000000 ) ; +#48319 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64542 ) ) ; +#48320 = EDGE_CURVE ( 'NONE', #86708, #15485, #394, .T. ) ; +#48321 = ADVANCED_FACE ( 'NONE', ( #45326 ), #99389, .F. ) ; +#48322 = ORIENTED_EDGE ( 'NONE', *, *, #60823, .F. ) ; +#48323 = EDGE_LOOP ( 'NONE', ( #55926, #72306, #82963, #97686 ) ) ; +#48324 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48325 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#48326 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48327 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#48328 = VERTEX_POINT ( 'NONE', #32064 ) ; +#48329 = PLANE ( 'NONE', #40186 ) ; +#48330 = FILL_AREA_STYLE ('',( #89120 ) ) ; +#48331 = SURFACE_SIDE_STYLE ('',( #32488 ) ) ; +#48332 = ORIENTED_EDGE ( 'NONE', *, *, #68935, .F. ) ; +#48333 = STYLED_ITEM ( 'NONE', ( #56783 ), #73677 ) ; +#48334 = FILL_AREA_STYLE_COLOUR ( '', #38773 ) ; +#48335 = EDGE_LOOP ( 'NONE', ( #1982, #66148, #55717, #16345 ) ) ; +#48336 = EDGE_LOOP ( 'NONE', ( #42010, #79265, #94245, #60477 ) ) ; +#48337 = CARTESIAN_POINT ( 'NONE', ( 1.049575243808681835, -1.178641562787471564, 0.8099999999998775957 ) ) ; +#48339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48338 = PRESENTATION_STYLE_ASSIGNMENT (( #71800 ) ) ; +#48340 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48341 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#48342 = VERTEX_POINT ( 'NONE', #23920 ) ; +#48343 = SURFACE_STYLE_FILL_AREA ( #86607 ) ; +#48344 = VECTOR ( 'NONE', #33398, 1000.000000000000000 ) ; +#48345 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#48346 = LINE ( 'NONE', #7906, #63709 ) ; +#48347 = AXIS2_PLACEMENT_3D ( 'NONE', #99477, #59818, #20968 ) ; +#48348 = ORIENTED_EDGE ( 'NONE', *, *, #17069, .F. ) ; +#48349 = PRESENTATION_STYLE_ASSIGNMENT (( #87623 ) ) ; +#48350 = ORIENTED_EDGE ( 'NONE', *, *, #43271, .F. ) ; +#48351 = ORIENTED_EDGE ( 'NONE', *, *, #30729, .F. ) ; +#48352 = FILL_AREA_STYLE ('',( #19171 ) ) ; +#48354 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#48353 = SURFACE_SIDE_STYLE ('',( #334 ) ) ; +#48355 = EDGE_CURVE ( 'NONE', #54723, #19133, #2434, .T. ) ; +#48356 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23852 ), #72747 ) ; +#48357 = FACE_OUTER_BOUND ( 'NONE', #31199, .T. ) ; +#48358 = AXIS2_PLACEMENT_3D ( 'NONE', #72674, #86482, #33898 ) ; +#48360 = SURFACE_SIDE_STYLE ('',( #3380 ) ) ; +#48359 = PLANE ( 'NONE', #63048 ) ; +#48361 = CARTESIAN_POINT ( 'NONE', ( 9.974076750250087997, 8.979438249749913226, 0.8991599999999999593 ) ) ; +#48362 = VECTOR ( 'NONE', #80992, 1000.000000000000000 ) ; +#48363 = VECTOR ( 'NONE', #6983, 1000.000000000000000 ) ; +#48364 = ADVANCED_FACE ( 'NONE', ( #39714 ), #55580, .T. ) ; +#48365 = PRESENTATION_STYLE_ASSIGNMENT (( #72826 ) ) ; +#48366 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100944 ) ; +#48367 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#48368 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2913, #49896, #28397, #18700 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48369 = SURFACE_STYLE_FILL_AREA ( #39660 ) ; +#48370 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48371 = ORIENTED_EDGE ( 'NONE', *, *, #58091, .F. ) ; +#48372 = AXIS2_PLACEMENT_3D ( 'NONE', #83593, #53448, #84568 ) ; +#48373 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#48374 = VECTOR ( 'NONE', #82632, 1000.000000000000000 ) ; +#48375 = EDGE_CURVE ( 'NONE', #25987, #3199, #48733, .T. ) ; +#48376 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#48377 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48378 = LINE ( 'NONE', #54512, #9219 ) ; +#48379 = LINE ( 'NONE', #70299, #20348 ) ; +#48380 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#48381 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48382 = EDGE_CURVE ( 'NONE', #58753, #1317, #16692, .T. ) ; +#48383 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#48384 = ORIENTED_EDGE ( 'NONE', *, *, #72523, .F. ) ; +#48385 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48386 = SURFACE_SIDE_STYLE ('',( #24394 ) ) ; +#48387 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48388 = LINE ( 'NONE', #55539, #53340 ) ; +#48389 = PRESENTATION_STYLE_ASSIGNMENT (( #39680 ) ) ; +#48390 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24322, 'distance_accuracy_value', 'NONE'); +#48391 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50410 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57852, #74647, #4186 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48392 = FILL_AREA_STYLE_COLOUR ( '', #88649 ) ; +#48394 = EDGE_CURVE ( 'NONE', #23664, #81283, #47376, .T. ) ; +#48393 = DIRECTION ( 'NONE', ( -2.168404344971010347E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48396 = EDGE_CURVE ( 'NONE', #55587, #54871, #80556, .T. ) ; +#48395 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8648700000000000276 ) ) ; +#48397 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68859 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99201, #52837, #83977 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48398 = EDGE_CURVE ( 'NONE', #92104, #36610, #19416, .T. ) ; +#48399 = EDGE_CURVE ( 'NONE', #54997, #33242, #41745, .T. ) ; +#48401 = SURFACE_STYLE_FILL_AREA ( #64691 ) ; +#48400 = STYLED_ITEM ( 'NONE', ( #98181 ), #13151 ) ; +#48402 = FILL_AREA_STYLE ('',( #32044 ) ) ; +#48403 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #50867, 'design' ) ; +#48404 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.004999999999999969746, -0.2399999999999999356 ) ) ; +#48405 = VERTEX_POINT ( 'NONE', #41252 ) ; +#48406 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48407 = FILL_AREA_STYLE_COLOUR ( '', #6189 ) ; +#48408 = SURFACE_STYLE_USAGE ( .BOTH. , #55565 ) ; +#48409 = ADVANCED_FACE ( 'NONE', ( #40745 ), #71883, .F. ) ; +#48410 = PLANE ( 'NONE', #72175 ) ; +#48411 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76058, 'distance_accuracy_value', 'NONE'); +#48412 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#48413 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7468 ) ) ; +#48414 = LINE ( 'NONE', #79532, #90540 ) ; +#48415 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.09999999999999999167, 0.8499999999999999778 ) ) ; +#48416 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48417 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#48418 = ORIENTED_EDGE ( 'NONE', *, *, #66621, .F. ) ; +#48419 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5616, 'distance_accuracy_value', 'NONE'); +#48421 = CARTESIAN_POINT ( 'NONE', ( -2.123820061220085265, 3.100000000000000089, 0.000000000000000000 ) ) ; +#48420 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48422 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76075 ), #66326 ) ; +#48423 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1206, 'distance_accuracy_value', 'NONE'); +#48424 = CIRCLE ( 'NONE', #4363, 0.3000000000000000444 ) ; +#48425 = VERTEX_POINT ( 'NONE', #89697 ) ; +#48426 = VERTEX_POINT ( 'NONE', #67214 ) ; +#48427 = ORIENTED_EDGE ( 'NONE', *, *, #51412, .F. ) ; +#48428 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#48429 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#48430 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.7099999999999999645, 0.4397321428571430157 ) ) ; +#48431 = VECTOR ( 'NONE', #44238, 1000.000000000000000 ) ; +#48432 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #42369 ) ; +#48433 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48434 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48436 = VERTEX_POINT ( 'NONE', #19763 ) ; +#48435 = ORIENTED_EDGE ( 'NONE', *, *, #24241, .F. ) ; +#48437 = EDGE_CURVE ( 'NONE', #92223, #60158, #65210, .T. ) ; +#48438 = ORIENTED_EDGE ( 'NONE', *, *, #85817, .F. ) ; +#48439 = ORIENTED_EDGE ( 'NONE', *, *, #5280, .F. ) ; +#48440 = SURFACE_STYLE_USAGE ( .BOTH. , #25963 ) ; +#48441 = AXIS2_PLACEMENT_3D ( 'NONE', #57066, #9965, #9478 ) ; +#48442 = CARTESIAN_POINT ( 'NONE', ( 1.715954649776489926, -1.507352529807550079, 0.8100000000000000533 ) ) ; +#48443 = PRESENTATION_STYLE_ASSIGNMENT (( #56094 ) ) ; +#48444 = ORIENTED_EDGE ( 'NONE', *, *, #15568, .F. ) ; +#48445 = EDGE_CURVE ( 'NONE', #46887, #36673, #23705, .T. ) ; +#48447 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65439 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32657, #55647, #33149 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48446 = LINE ( 'NONE', #34135, #17264 ) ; +#48448 = ORIENTED_EDGE ( 'NONE', *, *, #717, .F. ) ; +#48449 = SURFACE_SIDE_STYLE ('',( #95860 ) ) ; +#48450 = ORIENTED_EDGE ( 'NONE', *, *, #47907, .T. ) ; +#48451 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -13.35000000000000142 ) ) ; +#48452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48453 = ORIENTED_EDGE ( 'NONE', *, *, #41872, .F. ) ; +#48454 = VERTEX_POINT ( 'NONE', #4909 ) ; +#48455 = CARTESIAN_POINT ( 'NONE', ( 0.3189951478977410271, -1.329088006532930022, 0.8300000000000004041 ) ) ; +#48456 = LINE ( 'NONE', #88739, #49482 ) ; +#48457 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48458 = EDGE_CURVE ( 'NONE', #8286, #30515, #26424, .T. ) ; +#48459 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#48461 = ORIENTED_EDGE ( 'NONE', *, *, #28352, .T. ) ; +#48460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48462 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48463 = SURFACE_SIDE_STYLE ('',( #63775 ) ) ; +#48464 = SURFACE_SIDE_STYLE ('',( #63777 ) ) ; +#48465 = EDGE_LOOP ( 'NONE', ( #10314, #69468, #71903, #4211 ) ) ; +#48467 = SURFACE_STYLE_USAGE ( .BOTH. , #71422 ) ; +#48466 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48468 = CARTESIAN_POINT ( 'NONE', ( 0.07312563425034800113, -1.247909878090150082, 0.8299999999999999600 ) ) ; +#48469 = VERTEX_POINT ( 'NONE', #36109 ) ; +#48470 = ORIENTED_EDGE ( 'NONE', *, *, #95586, .F. ) ; +#48472 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#48471 = FACE_OUTER_BOUND ( 'NONE', #93362, .T. ) ; +#48473 = EDGE_CURVE ( 'NONE', #89863, #81943, #27946, .T. ) ; +#48474 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#48475 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48476 = SURFACE_SIDE_STYLE ('',( #77570 ) ) ; +#48477 = STYLED_ITEM ( 'NONE', ( #70297 ), #74012 ) ; +#48478 = LINE ( 'NONE', #32640, #62390 ) ; +#48479 = VERTEX_POINT ( 'NONE', #66224 ) ; +#48480 = CARTESIAN_POINT ( 'NONE', ( 0.3332327486577990050, -1.242627591519610109, 0.8299999999999999600 ) ) ; +#48481 = CARTESIAN_POINT ( 'NONE', ( -0.001323334233439310212, -1.190451802854979979, 0.8100000000000000533 ) ) ; +#48482 = ORIENTED_EDGE ( 'NONE', *, *, #11302, .F. ) ; +#48483 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14362, #22572, #68005, #83862 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48484 = FACE_OUTER_BOUND ( 'NONE', #44384, .T. ) ; +#48485 = SURFACE_SIDE_STYLE ('',( #24512 ) ) ; +#48486 = LINE ( 'NONE', #47450, #45124 ) ; +#48487 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48488 = VECTOR ( 'NONE', #73359, 1000.000000000000000 ) ; +#48489 = FACE_OUTER_BOUND ( 'NONE', #14812, .T. ) ; +#48491 = SURFACE_STYLE_FILL_AREA ( #9573 ) ; +#48490 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#48492 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#48493 = SURFACE_SIDE_STYLE ('',( #93373 ) ) ; +#48494 = FILL_AREA_STYLE_COLOUR ( '', #100387 ) ; +#48495 = CYLINDRICAL_SURFACE ( 'NONE', #85365, 0.05000000000000012768 ) ; +#48496 = VECTOR ( 'NONE', #97778, 1000.000000000000000 ) ; +#48497 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48498 = LINE ( 'NONE', #94405, #85912 ) ; +#48499 = SURFACE_STYLE_FILL_AREA ( #94407 ) ; +#48500 = VECTOR ( 'NONE', #77702, 1000.000000000000000 ) ; +#48501 = STYLED_ITEM ( 'NONE', ( #6390 ), #16936 ) ; +#48502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48503 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48504 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82739 ) ) ; +#48505 = FILL_AREA_STYLE_COLOUR ( '', #37245 ) ; +#48506 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5048 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9089, #78602, #15799 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48507 = SURFACE_SIDE_STYLE ('',( #96928 ) ) ; +#48508 = ADVANCED_FACE ( 'NONE', ( #20756 ), #59100, .T. ) ; +#48509 = AXIS2_PLACEMENT_3D ( 'NONE', #3901, #26906, #35080 ) ; +#48510 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63156 ) ) ; +#48511 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48512 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19619, 'distance_accuracy_value', 'NONE'); +#48513 = ORIENTED_EDGE ( 'NONE', *, *, #39615, .T. ) ; +#48514 = CLOSED_SHELL ( 'NONE', ( #79964, #35718, #7668, #91358, #61308, #6548 ) ) ; +#48515 = SURFACE_STYLE_USAGE ( .BOTH. , #46955 ) ; +#48516 = ORIENTED_EDGE ( 'NONE', *, *, #76476, .T. ) ; +#48517 = SURFACE_STYLE_FILL_AREA ( #86278 ) ; +#48518 = AXIS2_PLACEMENT_3D ( 'NONE', #94773, #57543, #33021 ) ; +#48519 = CARTESIAN_POINT ( 'NONE', ( 1.799170355476140015, -0.9218577280486121017, 0.8299999999999999600 ) ) ; +#48520 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80156 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28171, #82792, #67448 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48521 = FILL_AREA_STYLE ('',( #25039 ) ) ; +#48522 = EDGE_CURVE ( 'NONE', #70194, #5115, #26930, .T. ) ; +#48523 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48524 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2808578643762690841, -0.1434314575050761598 ) ) ; +#48525 = VECTOR ( 'NONE', #73559, 1000.000000000000000 ) ; +#48526 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.000000000000000000 ) ) ; +#48527 = ORIENTED_EDGE ( 'NONE', *, *, #3063, .T. ) ; +#48528 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#48529 = ORIENTED_EDGE ( 'NONE', *, *, #24548, .F. ) ; +#48530 = PLANE ( 'NONE', #31947 ) ; +#48531 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48532 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#48533 = LINE ( 'NONE', #72001, #3042 ) ; +#48534 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48535 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48536 = ORIENTED_EDGE ( 'NONE', *, *, #95826, .F. ) ; +#48537 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#48538 = MANIFOLD_SOLID_BREP ( 'ÊäÈë30', #1323 ) ; +#48539 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48540 = ORIENTED_EDGE ( 'NONE', *, *, #52385, .F. ) ; +#48541 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41973 ) ) ; +#48542 = SURFACE_STYLE_FILL_AREA ( #46996 ) ; +#48543 = ORIENTED_EDGE ( 'NONE', *, *, #51469, .F. ) ; +#48544 = SURFACE_SIDE_STYLE ('',( #30787 ) ) ; +#48545 = AXIS2_PLACEMENT_3D ( 'NONE', #37053, #99228, #37555 ) ; +#48546 = FILL_AREA_STYLE_COLOUR ( '', #91351 ) ; +#48547 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48548 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48549 = FILL_AREA_STYLE ('',( #17361 ) ) ; +#48550 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#48551 = SURFACE_SIDE_STYLE ('',( #70999 ) ) ; +#48552 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48554 = ORIENTED_EDGE ( 'NONE', *, *, #18309, .T. ) ; +#48553 = ORIENTED_EDGE ( 'NONE', *, *, #4583, .F. ) ; +#48555 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333330195, 2.100000000000000089, 1.747825839084982648E-76 ) ) ; +#48556 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48557 = ORIENTED_EDGE ( 'NONE', *, *, #31658, .F. ) ; +#48558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89349 ) ) ; +#48559 = VECTOR ( 'NONE', #87039, 1000.000000000000000 ) ; +#48561 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#48560 = LINE ( 'NONE', #95975, #9700 ) ; +#48562 = ORIENTED_EDGE ( 'NONE', *, *, #10189, .T. ) ; +#48563 = ADVANCED_FACE ( 'NONE', ( #12515 ), #76376, .T. ) ; +#48564 = ORIENTED_EDGE ( 'NONE', *, *, #29674, .T. ) ; +#48565 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#48566 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 8.859075087692251214E-35, 0.03429000000000000103 ) ) ; +#48567 = LINE ( 'NONE', #10647, #74089 ) ; +#48568 = PRESENTATION_STYLE_ASSIGNMENT (( #1068 ) ) ; +#48569 = STYLED_ITEM ( 'NONE', ( #21189 ), #79378 ) ; +#48571 = SURFACE_STYLE_USAGE ( .BOTH. , #78665 ) ; +#48570 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#48572 = PRESENTATION_STYLE_ASSIGNMENT (( #24606 ) ) ; +#48573 = ORIENTED_EDGE ( 'NONE', *, *, #28636, .F. ) ; +#48574 = EDGE_LOOP ( 'NONE', ( #89602, #4108, #59669, #16215 ) ) ; +#48575 = LINE ( 'NONE', #95484, #60071 ) ; +#48576 = ORIENTED_EDGE ( 'NONE', *, *, #84870, .F. ) ; +#48577 = FILL_AREA_STYLE ('',( #16357 ) ) ; +#48578 = AXIS2_PLACEMENT_3D ( 'NONE', #64630, #9905, #93704 ) ; +#48579 = VECTOR ( 'NONE', #57183, 1000.000000000000000 ) ; +#48580 = ORIENTED_EDGE ( 'NONE', *, *, #18074, .T. ) ; +#48581 = VECTOR ( 'NONE', #91057, 1000.000000000000000 ) ; +#48582 = FILL_AREA_STYLE ('',( #47035 ) ) ; +#48583 = SURFACE_STYLE_USAGE ( .BOTH. , #49585 ) ; +#48584 = VERTEX_POINT ( 'NONE', #84539 ) ; +#48585 = CLOSED_SHELL ( 'NONE', ( #43610, #40689, #91582, #54188, #98800, #51893 ) ) ; +#48586 = VERTEX_POINT ( 'NONE', #76892 ) ; +#48587 = EDGE_CURVE ( 'NONE', #27727, #91350, #29425, .T. ) ; +#48588 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40420 ), #27366 ) ; +#48589 = VECTOR ( 'NONE', #74526, 1000.000000000000000 ) ; +#48590 = FILL_AREA_STYLE_COLOUR ( '', #10544 ) ; +#48591 = SURFACE_STYLE_USAGE ( .BOTH. , #48072 ) ; +#48592 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#48593 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69674 ), #1259 ) ; +#48594 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48596 = PLANE ( 'NONE', #50882 ) ; +#48595 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28166 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19295, #3986, #43286 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48597 = LINE ( 'NONE', #64402, #22677 ) ; +#48599 = DIRECTION ( 'NONE', ( -2.058195874565369951E-47, -0.000000000000000000, 1.000000000000000000 ) ) ; +#48598 = CARTESIAN_POINT ( 'NONE', ( -0.5545805800045841005, -1.188240277164636094, 0.8300000000000001821 ) ) ; +#48600 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48601 = STYLED_ITEM ( 'NONE', ( #26112 ), #49903 ) ; +#48602 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, 5.606048033198377238E-17, 0.8499999999999999778 ) ) ; +#48603 = PRESENTATION_STYLE_ASSIGNMENT (( #3121 ) ) ; +#48604 = ORIENTED_EDGE ( 'NONE', *, *, #56206, .T. ) ; +#48605 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48606 = LINE ( 'NONE', #78222, #52927 ) ; +#48607 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48608 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48609 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706229E-17, 0.7578679656440356904, -0.2000000000000000111 ) ) ; +#48611 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#48610 = PRESENTATION_STYLE_ASSIGNMENT (( #25142 ) ) ; +#48612 = LINE ( 'NONE', #39400, #1073 ) ; +#48613 = ADVANCED_FACE ( 'NONE', ( #14555 ), #37605, .T. ) ; +#48614 = VECTOR ( 'NONE', #89012, 1000.000000000000000 ) ; +#48615 = PLANE ( 'NONE', #72739 ) ; +#48616 = AXIS2_PLACEMENT_3D ( 'NONE', #72500, #63375, #16841 ) ; +#48617 = LINE ( 'NONE', #32270, #20003 ) ; +#48618 = LINE ( 'NONE', #28621, #83369 ) ; +#48619 = FACE_OUTER_BOUND ( 'NONE', #69718, .T. ) ; +#48620 = ORIENTED_EDGE ( 'NONE', *, *, #25337, .F. ) ; +#48621 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.1000000000000000056, -11.91999999999999993 ) ) ; +#48622 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48623 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.699999999999999956, -0.02000000000000560010 ) ) ; +#48624 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48625 = CIRCLE ( 'NONE', #4562, 0.04341445994543620401 ) ; +#48626 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46984 ) ) ; +#48627 = VECTOR ( 'NONE', #41972, 1000.000000000000000 ) ; +#48628 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26280, 'distance_accuracy_value', 'NONE'); +#48629 = ORIENTED_EDGE ( 'NONE', *, *, #58442, .F. ) ; +#48630 = AXIS2_PLACEMENT_3D ( 'NONE', #20862, #29527, #45315 ) ; +#48631 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48632 = FILL_AREA_STYLE ('',( #23614 ) ) ; +#48633 = PLANE ( 'NONE', #92529 ) ; +#48634 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#48635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73036 ), #82867 ) ; +#48636 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48637 = EDGE_CURVE ( 'NONE', #58180, #13557, #60592, .T. ) ; +#48638 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48639 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22516 ), #14381 ) ; +#48640 = VERTEX_POINT ( 'NONE', #40625 ) ; +#48641 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#48642 = ORIENTED_EDGE ( 'NONE', *, *, #51816, .T. ) ; +#48643 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79838 ), #53724 ) ; +#48644 = SURFACE_SIDE_STYLE ('',( #47102 ) ) ; +#48645 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15625, 'distance_accuracy_value', 'NONE'); +#48646 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999959992 ) ) ; +#48647 = LINE ( 'NONE', #79790, #23490 ) ; +#48648 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#48649 = FACE_OUTER_BOUND ( 'NONE', #78714, .T. ) ; +#48650 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24005 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8873, #29914, #92198 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48651 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#48652 = FILL_AREA_STYLE ('',( #17461 ) ) ; +#48653 = CLOSED_SHELL ( 'NONE', ( #81122, #32461, #71366, #63434, #23873, #51093 ) ) ; +#48654 = EDGE_LOOP ( 'NONE', ( #41287, #62015, #31814, #20253 ) ) ; +#48655 = FILL_AREA_STYLE_COLOUR ( '', #67776 ) ; +#48656 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94228 ) ) ; +#48657 = FILL_AREA_STYLE ('',( #1691 ) ) ; +#48658 = ORIENTED_EDGE ( 'NONE', *, *, #9518, .F. ) ; +#48659 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.05000000000000000278, 0.2100000000000000200 ) ) ; +#48660 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48661 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.616666666666666252, 0.000000000000000000 ) ) ; +#48662 = VERTEX_POINT ( 'NONE', #48300 ) ; +#48663 = STYLED_ITEM ( 'NONE', ( #9072 ), #50558 ) ; +#48664 = AXIS2_PLACEMENT_3D ( 'NONE', #58694, #42349, #89794 ) ; +#48665 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#48666 = SURFACE_STYLE_FILL_AREA ( #78773 ) ; +#48667 = VECTOR ( 'NONE', #14611, 1000.000000000000000 ) ; +#48668 = SURFACE_SIDE_STYLE ('',( #3191 ) ) ; +#48669 = SURFACE_STYLE_FILL_AREA ( #70094 ) ; +#48670 = PLANE ( 'NONE', #74098 ) ; +#48671 = ORIENTED_EDGE ( 'NONE', *, *, #91425, .T. ) ; +#48672 = FILL_AREA_STYLE_COLOUR ( '', #57772 ) ; +#48673 = ORIENTED_EDGE ( 'NONE', *, *, #24054, .F. ) ; +#48674 = FILL_AREA_STYLE_COLOUR ( '', #52509 ) ; +#48675 = FILL_AREA_STYLE ('',( #18502 ) ) ; +#48676 = ADVANCED_FACE ( 'NONE', ( #31945 ), #95700, .T. ) ; +#48677 = VERTEX_POINT ( 'NONE', #18091 ) ; +#48678 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48679 = FILL_AREA_STYLE ('',( #79303 ) ) ; +#48680 = CARTESIAN_POINT ( 'NONE', ( 1.792693045999540047, -1.018845982455530041, 0.8300000000000004041 ) ) ; +#48681 = AXIS2_PLACEMENT_3D ( 'NONE', #91345, #4556, #75042 ) ; +#48682 = SURFACE_STYLE_USAGE ( .BOTH. , #25225 ) ; +#48683 = ORIENTED_EDGE ( 'NONE', *, *, #20089, .T. ) ; +#48685 = ORIENTED_EDGE ( 'NONE', *, *, #53266, .F. ) ; +#48684 = ORIENTED_EDGE ( 'NONE', *, *, #25154, .T. ) ; +#48686 = ORIENTED_EDGE ( 'NONE', *, *, #19145, .T. ) ; +#48687 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597380222, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#48688 = VECTOR ( 'NONE', #24016, 1000.000000000000000 ) ; +#48689 = VERTEX_POINT ( 'NONE', #70737 ) ; +#48690 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56869 ) ) ; +#48692 = VERTEX_POINT ( 'NONE', #56476 ) ; +#48691 = FILL_AREA_STYLE ('',( #73179 ) ) ; +#48693 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#48694 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#48695 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48696 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#48697 = ORIENTED_EDGE ( 'NONE', *, *, #59604, .T. ) ; +#48698 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5833333333333333703, 0.000000000000000000 ) ) ; +#48699 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.9000000000000020206, 0.1829999999999619986 ) ) ; +#48700 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48701 = ORIENTED_EDGE ( 'NONE', *, *, #44041, .F. ) ; +#48702 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69863 ), #71496 ) ; +#48703 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48704 = MANIFOLD_SOLID_BREP ( 'ÊäÈë67', #14243 ) ; +#48705 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48706 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#48707 = ORIENTED_EDGE ( 'NONE', *, *, #44777, .F. ) ; +#48708 = STYLED_ITEM ( 'NONE', ( #71577 ), #79923 ) ; +#48709 = ORIENTED_EDGE ( 'NONE', *, *, #7679, .F. ) ; +#48710 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53912, #63103, #47759, #15574 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48711 = EDGE_CURVE ( 'NONE', #25174, #47667, #8362, .T. ) ; +#48712 = ADVANCED_FACE ( 'NONE', ( #54945 ), #16085, .F. ) ; +#48713 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48715 = CARTESIAN_POINT ( 'NONE', ( 4.557639000000000884, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#48714 = SURFACE_STYLE_USAGE ( .BOTH. , #88001 ) ; +#48716 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#48717 = VECTOR ( 'NONE', #22754, 999.9999999999998863 ) ; +#48718 = VECTOR ( 'NONE', #64568, 1000.000000000000000 ) ; +#48719 = FACE_OUTER_BOUND ( 'NONE', #100878, .T. ) ; +#48720 = VECTOR ( 'NONE', #23782, 1000.000000000000000 ) ; +#48721 = FILL_AREA_STYLE ('',( #25255 ) ) ; +#48722 = CARTESIAN_POINT ( 'NONE', ( -0.8116130169878562617, 1.464383040805290026, 0.8100000000000000533 ) ) ; +#48723 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#48724 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48725 = ADVANCED_FACE ( 'NONE', ( #10885 ), #96214, .F. ) ; +#48726 = EDGE_CURVE ( 'NONE', #43664, #80853, #80954, .T. ) ; +#48727 = PRESENTATION_STYLE_ASSIGNMENT (( #17530 ) ) ; +#48728 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48729 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999929778, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#48730 = ORIENTED_EDGE ( 'NONE', *, *, #72191, .F. ) ; +#48731 = SURFACE_STYLE_USAGE ( .BOTH. , #62541 ) ; +#48732 = PLANE ( 'NONE', #94366 ) ; +#48733 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1428, #25433, #57084, #86686 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48734 = FACE_OUTER_BOUND ( 'NONE', #4015, .T. ) ; +#48735 = ORIENTED_EDGE ( 'NONE', *, *, #37174, .F. ) ; +#48736 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48737 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92051 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19045, #57917, #80874 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48740 = PLANE ( 'NONE', #2012 ) ; +#48739 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#48738 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48741 = LINE ( 'NONE', #38540, #87968 ) ; +#48742 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85380, 'distance_accuracy_value', 'NONE'); +#48743 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#48744 = CARTESIAN_POINT ( 'NONE', ( 0.2414713305586040082, -1.411255840060410049, 0.8100000000000000533 ) ) ; +#48745 = EDGE_CURVE ( 'NONE', #71387, #466, #8471, .T. ) ; +#48746 = FACE_OUTER_BOUND ( 'NONE', #25664, .T. ) ; +#48747 = FILL_AREA_STYLE ('',( #17549 ) ) ; +#48748 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #60746, #92351, #64248, #95350 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48749 = FILL_AREA_STYLE_COLOUR ( '', #516 ) ; +#48750 = EDGE_LOOP ( 'NONE', ( #72508, #50675, #58897, #21903 ) ) ; +#48751 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#48752 = LINE ( 'NONE', #17555, #21687 ) ; +#48753 = SURFACE_STYLE_FILL_AREA ( #2283 ) ; +#48754 = FACE_OUTER_BOUND ( 'NONE', #4451, .T. ) ; +#48755 = LINE ( 'NONE', #62569, #63285 ) ; +#48756 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19431 ), #99215 ) ; +#48757 = PLANE ( 'NONE', #52388 ) ; +#48758 = SURFACE_STYLE_USAGE ( .BOTH. , #11354 ) ; +#48759 = LINE ( 'NONE', #1788, #81144 ) ; +#48760 = LINE ( 'NONE', #39566, #10353 ) ; +#48761 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48762 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48763 = EDGE_CURVE ( 'NONE', #69664, #73012, #81462, .T. ) ; +#48765 = DIRECTION ( 'NONE', ( 0.7071071146859689849, -0.7071064476869689530, 0.000000000000000000 ) ) ; +#48764 = VECTOR ( 'NONE', #92615, 1000.000000000000000 ) ; +#48766 = VECTOR ( 'NONE', #6947, 1000.000000000000000 ) ; +#48767 = DIRECTION ( 'NONE', ( -1.000000000000000000, 8.052359004764721492E-109, 6.165170508236590408E-78 ) ) ; +#48768 = EDGE_CURVE ( 'NONE', #35737, #20872, #11882, .T. ) ; +#48769 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#48770 = ORIENTED_EDGE ( 'NONE', *, *, #52244, .T. ) ; +#48771 = VERTEX_POINT ( 'NONE', #19119 ) ; +#48772 = VECTOR ( 'NONE', #98078, 1000.000000000000000 ) ; +#48773 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #3010 ) ; +#48774 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.300000000000000044, -0.02000000000000630093 ) ) ; +#48776 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48775 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32507 ) ) ; +#48777 = CARTESIAN_POINT ( 'NONE', ( 0.2039600559557959991, -1.343068553933169929, 0.8299999999999999600 ) ) ; +#48778 = PLANE ( 'NONE', #4707 ) ; +#48779 = FACE_OUTER_BOUND ( 'NONE', #1188, .T. ) ; +#48780 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#48781 = FILL_AREA_STYLE ('',( #65576 ) ) ; +#48782 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48783 = ORIENTED_EDGE ( 'NONE', *, *, #57129, .F. ) ; +#48784 = SURFACE_STYLE_USAGE ( .BOTH. , #2315 ) ; +#48785 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#48786 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54525 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20889, #98906, #29549 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48787 = PLANE ( 'NONE', #63933 ) ; +#48789 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886600000000008, 0.8991599999999999593 ) ) ; +#48788 = VECTOR ( 'NONE', #11697, 999.9999999999998863 ) ; +#48790 = ORIENTED_EDGE ( 'NONE', *, *, #46840, .F. ) ; +#48791 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#48792 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#48793 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68271 ) ) ; +#48794 = SURFACE_STYLE_USAGE ( .BOTH. , #42621 ) ; +#48795 = ADVANCED_FACE ( 'NONE', ( #1049 ), #59497, .F. ) ; +#48796 = AXIS2_PLACEMENT_3D ( 'NONE', #77494, #40739, #49389 ) ; +#48797 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000020206, 0.1829999999999619986 ) ) ; +#48798 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#48799 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 1.100000000000000089 ) ) ; +#48800 = STYLED_ITEM ( 'NONE', ( #88520 ), #1335 ) ; +#48801 = ORIENTED_EDGE ( 'NONE', *, *, #69290, .F. ) ; +#48802 = FILL_AREA_STYLE ('',( #32457 ) ) ; +#48803 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6277 ) ) ; +#48804 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32481, 'distance_accuracy_value', 'NONE'); +#48805 = FILL_AREA_STYLE ('',( #17607 ) ) ; +#48806 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.57000000000000028 ) ) ; +#48807 = EDGE_CURVE ( 'NONE', #66256, #51382, #31687, .T. ) ; +#48808 = ORIENTED_EDGE ( 'NONE', *, *, #58267, .T. ) ; +#48809 = FACE_OUTER_BOUND ( 'NONE', #87155, .T. ) ; +#48810 = EDGE_CURVE ( 'NONE', #27932, #17890, #36482, .T. ) ; +#48811 = SURFACE_STYLE_FILL_AREA ( #17122 ) ; +#48812 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48813 = VECTOR ( 'NONE', #27811, 1000.000000000000000 ) ; +#48814 = EDGE_CURVE ( 'NONE', #46129, #40128, #78644, .T. ) ; +#48815 = ORIENTED_EDGE ( 'NONE', *, *, #81466, .T. ) ; +#48817 = ORIENTED_EDGE ( 'NONE', *, *, #68163, .F. ) ; +#48816 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#48818 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78542, 'distance_accuracy_value', 'NONE'); +#48819 = CYLINDRICAL_SURFACE ( 'NONE', #59570, 0.009999999999999998473 ) ; +#48820 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48821 = VERTEX_POINT ( 'NONE', #59985 ) ; +#48822 = SURFACE_STYLE_FILL_AREA ( #56998 ) ; +#48824 = ORIENTED_EDGE ( 'NONE', *, *, #68379, .T. ) ; +#48823 = AXIS2_PLACEMENT_3D ( 'NONE', #34016, #96744, #10918 ) ; +#48825 = DIRECTION ( 'NONE', ( -0.7071067816865476141, 0.7071067806865475314, 0.000000000000000000 ) ) ; +#48826 = ORIENTED_EDGE ( 'NONE', *, *, #49791, .F. ) ; +#48827 = ORIENTED_EDGE ( 'NONE', *, *, #395, .T. ) ; +#48828 = EDGE_CURVE ( 'NONE', #97102, #51183, #39333, .T. ) ; +#48829 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#48830 = STYLED_ITEM ( 'NONE', ( #22679 ), #92845 ) ; +#48831 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93888 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52904, #6348, #70190 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48832 = SURFACE_STYLE_USAGE ( .BOTH. , #18650 ) ; +#48833 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48834 = ORIENTED_EDGE ( 'NONE', *, *, #9677, .F. ) ; +#48835 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38611 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48189, #90490, #34891 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48836 = FACE_OUTER_BOUND ( 'NONE', #73159, .T. ) ; +#48837 = ORIENTED_EDGE ( 'NONE', *, *, #23440, .F. ) ; +#48838 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48839 = VERTEX_POINT ( 'NONE', #37486 ) ; +#48840 = EDGE_LOOP ( 'NONE', ( #92953, #72030, #43494, #24320 ) ) ; +#48841 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#48843 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#48842 = LINE ( 'NONE', #41684, #13415 ) ; +#48845 = AXIS2_PLACEMENT_3D ( 'NONE', #70621, #78790, #32343 ) ; +#48844 = CARTESIAN_POINT ( 'NONE', ( -1.014711377400389969, -1.276477384597439979, 0.8100000000000000533 ) ) ; +#48846 = ADVANCED_FACE ( 'NONE', ( #68587 ), #51802, .T. ) ; +#48847 = SURFACE_STYLE_FILL_AREA ( #56526 ) ; +#48848 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48849 = EDGE_CURVE ( 'NONE', #86070, #88085, #12899, .T. ) ; +#48850 = VECTOR ( 'NONE', #17544, 1000.000000000000000 ) ; +#48851 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48852 = CARTESIAN_POINT ( 'NONE', ( -0.09936535710386810993, -1.163903542943879987, 0.8100000000000000533 ) ) ; +#48853 = LINE ( 'NONE', #85613, #77998 ) ; +#48854 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48855 = VERTEX_POINT ( 'NONE', #44593 ) ; +#48856 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2999999999999999889, -12.44500000000000028 ) ) ; +#48857 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48858 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#48859 = AXIS2_PLACEMENT_3D ( 'NONE', #40830, #47458, #9576 ) ; +#48860 = FILL_AREA_STYLE ('',( #96277 ) ) ; +#48861 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999689, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#48862 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48863 = EDGE_CURVE ( 'NONE', #84179, #78436, #68081, .T. ) ; +#48864 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8648700000000000276 ) ) ; +#48865 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48866 = VECTOR ( 'NONE', #56652, 1000.000000000000114 ) ; +#48867 = ORIENTED_EDGE ( 'NONE', *, *, #26468, .F. ) ; +#48869 = MANIFOLD_SOLID_BREP ( 'ÊäÈë119', #48653 ) ; +#48868 = CARTESIAN_POINT ( 'NONE', ( -0.5614853896103889630, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#48872 = ADVANCED_FACE ( 'NONE', ( #33725 ), #79168, .T. ) ; +#48871 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86983, 'distance_accuracy_value', 'NONE'); +#48870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48873 = FACE_OUTER_BOUND ( 'NONE', #957, .T. ) ; +#48874 = SURFACE_STYLE_USAGE ( .BOTH. , #16658 ) ; +#48875 = FILL_AREA_STYLE ('',( #94785 ) ) ; +#48876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39088 ) ) ; +#48877 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48878 = SURFACE_STYLE_FILL_AREA ( #56555 ) ; +#48879 = SURFACE_STYLE_USAGE ( .BOTH. , #78998 ) ; +#48880 = EDGE_CURVE ( 'NONE', #41056, #48586, #16837, .T. ) ; +#48881 = PRESENTATION_STYLE_ASSIGNMENT (( #56045 ) ) ; +#48882 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#48883 = CARTESIAN_POINT ( 'NONE', ( -0.4406630133853430276, 0.3469465759269649840, 0.8100000000000000533 ) ) ; +#48884 = FILL_AREA_STYLE ('',( #80529 ) ) ; +#48885 = ADVANCED_FACE ( 'NONE', ( #88332 ), #42387, .F. ) ; +#48886 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48887 = CARTESIAN_POINT ( 'NONE', ( 1.901168164643999736, -1.316888414733939916, 0.8100000000000004974 ) ) ; +#48888 = PRESENTATION_STYLE_ASSIGNMENT (( #369 ) ) ; +#48889 = SURFACE_SIDE_STYLE ('',( #64203 ) ) ; +#48890 = VERTEX_POINT ( 'NONE', #12146 ) ; +#48891 = SURFACE_STYLE_FILL_AREA ( #56572 ) ; +#48892 = LINE ( 'NONE', #65201, #47752 ) ; +#48893 = VECTOR ( 'NONE', #36459, 1000.000000000000000 ) ; +#48895 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#48894 = PRESENTATION_STYLE_ASSIGNMENT (( #55568 ) ) ; +#48896 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48897 = VECTOR ( 'NONE', #4712, 1000.000000000000000 ) ; +#48898 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#48899 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48900 = EDGE_CURVE ( 'NONE', #51408, #37515, #44843, .T. ) ; +#48901 = ORIENTED_EDGE ( 'NONE', *, *, #48320, .T. ) ; +#48902 = FILL_AREA_STYLE ('',( #11501 ) ) ; +#48903 = FILL_AREA_STYLE_COLOUR ( '', #17937 ) ; +#48904 = SURFACE_STYLE_FILL_AREA ( #72880 ) ; +#48905 = VECTOR ( 'NONE', #84826, 1000.000000000000000 ) ; +#48907 = SURFACE_SIDE_STYLE ('',( #17724 ) ) ; +#48906 = STYLED_ITEM ( 'NONE', ( #3810 ), #85395 ) ; +#48908 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60366 ) ) ; +#48909 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#48910 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48911 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#48912 = AXIS2_PLACEMENT_3D ( 'NONE', #5123, #84279, #21480 ) ; +#48913 = EDGE_CURVE ( 'NONE', #54090, #35131, #28550, .T. ) ; +#48914 = AXIS2_PLACEMENT_3D ( 'NONE', #61101, #14563, #6858 ) ; +#48915 = ORIENTED_EDGE ( 'NONE', *, *, #72630, .T. ) ; +#48916 = ORIENTED_EDGE ( 'NONE', *, *, #73101, .F. ) ; +#48917 = FILL_AREA_STYLE ('',( #87702 ) ) ; +#48918 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48919 = ORIENTED_EDGE ( 'NONE', *, *, #67483, .F. ) ; +#48920 = EDGE_CURVE ( 'NONE', #60664, #14220, #89339, .T. ) ; +#48921 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48922 = SURFACE_STYLE_USAGE ( .BOTH. , #71897 ) ; +#48923 = PLANE ( 'NONE', #17047 ) ; +#48924 = SHAPE_DEFINITION_REPRESENTATION ( #64659, #47469 ) ; +#48925 = FACE_OUTER_BOUND ( 'NONE', #100637, .T. ) ; +#48926 = PLANE ( 'NONE', #14975 ) ; +#48927 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#48929 = EDGE_LOOP ( 'NONE', ( #91137, #10601, #48042, #8759 ) ) ; +#48928 = ORIENTED_EDGE ( 'NONE', *, *, #47307, .T. ) ; +#48930 = AXIS2_PLACEMENT_3D ( 'NONE', #13604, #60191, #38181 ) ; +#48931 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#48932 = EDGE_CURVE ( 'NONE', #88871, #3341, #19383, .T. ) ; +#48933 = ORIENTED_EDGE ( 'NONE', *, *, #27877, .F. ) ; +#48934 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50892, 'distance_accuracy_value', 'NONE'); +#48935 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2808578643762690841, -0.1499999999999999944 ) ) ; +#48936 = ORIENTED_EDGE ( 'NONE', *, *, #78770, .F. ) ; +#48937 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #63786, #54624, #33652, #78081, #1991, #86746, #56127, #17281, #16760, #23456, #86230, #87239, #25488, #85722, #47943, #48963, #15758, #78565, #17781 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.289444789457627467E-05, 2.549973415362091972E-05, 3.801561174744572423E-05, 5.040511403747544256E-05, 6.264100167992721932E-05, 7.454698067567129896E-05, 8.605472911504119657E-05, 9.753033114701231405E-05, 0.0001088881519317733875, 0.0001202550761410785967, 0.0001315881507700809915, 0.0001431828865404820837, 0.0001550584193850497916, 0.0001670638921105410213, 0.0001793942156805982291, 0.0001922938194067799061 ), + .UNSPECIFIED. ) ; +#48938 = PLANE ( 'NONE', #7429 ) ; +#48939 = CIRCLE ( 'NONE', #19551, 0.009999999999999998473 ) ; +#48940 = ORIENTED_EDGE ( 'NONE', *, *, #289, .F. ) ; +#48941 = AXIS2_PLACEMENT_3D ( 'NONE', #45297, #31019, #39179 ) ; +#48942 = ORIENTED_EDGE ( 'NONE', *, *, #55534, .F. ) ; +#48944 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#48943 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8648700000000000276 ) ) ; +#48945 = ORIENTED_EDGE ( 'NONE', *, *, #76844, .F. ) ; +#48946 = EDGE_CURVE ( 'NONE', #95326, #69070, #36236, .T. ) ; +#48947 = VERTEX_POINT ( 'NONE', #90846 ) ; +#48949 = EDGE_CURVE ( 'NONE', #28558, #4673, #59753, .T. ) ; +#48948 = STYLED_ITEM ( 'NONE', ( #95289 ), #9910 ) ; +#48951 = FACE_OUTER_BOUND ( 'NONE', #52089, .T. ) ; +#48950 = PLANE ( 'NONE', #85306 ) ; +#48952 = SURFACE_SIDE_STYLE ('',( #79081 ) ) ; +#48953 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#48956 = ORIENTED_EDGE ( 'NONE', *, *, #34492, .T. ) ; +#48955 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48004 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12893, #36969, #93923 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48954 = LINE ( 'NONE', #17268, #38023 ) ; +#48957 = SURFACE_SIDE_STYLE ('',( #10038 ) ) ; +#48958 = CARTESIAN_POINT ( 'NONE', ( -0.2353471038102170343, -0.9412361261466359874, 0.8100000000000000533 ) ) ; +#48959 = ORIENTED_EDGE ( 'NONE', *, *, #11456, .F. ) ; +#48960 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#48961 = ORIENTED_EDGE ( 'NONE', *, *, #89949, .F. ) ; +#48962 = ORIENTED_EDGE ( 'NONE', *, *, #23938, .T. ) ; +#48963 = CARTESIAN_POINT ( 'NONE', ( 1.820901995646819982, -1.357122040133029950, 0.8300000000000002931 ) ) ; +#48964 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#48965 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41303, #70915, #62770, #56638 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48966 = EDGE_CURVE ( 'NONE', #17592, #24841, #27573, .T. ) ; +#48967 = STYLED_ITEM ( 'NONE', ( #11502 ), #33354 ) ; +#48968 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.000000000000000000 ) ) ; +#48969 = ADVANCED_FACE ( 'NONE', ( #60238 ), #83694, .T. ) ; +#48970 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#48971 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #5709 ) ; +#48972 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#48974 = FILL_AREA_STYLE_COLOUR ( '', #97699 ) ; +#48973 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94653, #55899, #47197, #49235 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#48975 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27402, 'distance_accuracy_value', 'NONE'); +#48976 = FILL_AREA_STYLE_COLOUR ( '', #23092 ) ; +#48977 = ORIENTED_EDGE ( 'NONE', *, *, #100048, .T. ) ; +#48978 = CARTESIAN_POINT ( 'NONE', ( -1.566666666666666652, -3.500000000000000000, 0.000000000000000000 ) ) ; +#48979 = FILL_AREA_STYLE ('',( #25501 ) ) ; +#48980 = ORIENTED_EDGE ( 'NONE', *, *, #21246, .F. ) ; +#48981 = SURFACE_STYLE_FILL_AREA ( #10060 ) ; +#48983 = FILL_AREA_STYLE_COLOUR ( '', #30139 ) ; +#48982 = AXIS2_PLACEMENT_3D ( 'NONE', #80109, #63287, #94372 ) ; +#48984 = LINE ( 'NONE', #10557, #734 ) ; +#48985 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76851 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39266, #14230, #92848 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#48986 = PLANE ( 'NONE', #43824 ) ; +#48988 = SURFACE_SIDE_STYLE ('',( #94889 ) ) ; +#48987 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#48989 = SURFACE_STYLE_USAGE ( .BOTH. , #79120 ) ; +#48990 = CARTESIAN_POINT ( 'NONE', ( -2.616666666666666252, -3.100000000000000533, 0.000000000000000000 ) ) ; +#48991 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#48992 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#48993 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#48994 = SURFACE_STYLE_USAGE ( .BOTH. , #79126 ) ; +#48995 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#48996 = CARTESIAN_POINT ( 'NONE', ( 0.3385502766025340060, -0.9005362424757039630, 0.8100000000000000533 ) ) ; +#48997 = STYLED_ITEM ( 'NONE', ( #56678 ), #80772 ) ; +#48998 = SURFACE_SIDE_STYLE ('',( #3018 ) ) ; +#48999 = CYLINDRICAL_SURFACE ( 'NONE', #34407, 0.05000000000000012768 ) ; +#49000 = LINE ( 'NONE', #95406, #26811 ) ; +#49001 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58778 ), #27793 ) ; +#49002 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#49003 = AXIS2_PLACEMENT_3D ( 'NONE', #84985, #39542, #7801 ) ; +#49004 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.000000000000000000 ) ) ; +#49005 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999334, -0.1499999999999999667, -0.01999999999999999695 ) ) ; +#49006 = EDGE_CURVE ( 'NONE', #28694, #15347, #14015, .T. ) ; +#49007 = VECTOR ( 'NONE', #75412, 1000.000000000000000 ) ; +#49008 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19614 ), #44096 ) ; +#49009 = EDGE_CURVE ( 'NONE', #57188, #76911, #29065, .T. ) ; +#49010 = ORIENTED_EDGE ( 'NONE', *, *, #15790, .T. ) ; +#49011 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8199999999999999512 ) ) ; +#49012 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81562, 'distance_accuracy_value', 'NONE'); +#49013 = ORIENTED_EDGE ( 'NONE', *, *, #88738, .F. ) ; +#49014 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68657, 'distance_accuracy_value', 'NONE'); +#49015 = PRESENTATION_STYLE_ASSIGNMENT (( #34713 ) ) ; +#49016 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#49017 = AXIS2_PLACEMENT_3D ( 'NONE', #32036, #72337, #80526 ) ; +#49018 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49019 = SURFACE_SIDE_STYLE ('',( #25540 ) ) ; +#49020 = PLANE ( 'NONE', #15666 ) ; +#49021 = VERTEX_POINT ( 'NONE', #5532 ) ; +#49022 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#49023 = EDGE_CURVE ( 'NONE', #55852, #72043, #36729, .T. ) ; +#49024 = ORIENTED_EDGE ( 'NONE', *, *, #17238, .T. ) ; +#49025 = PRESENTATION_STYLE_ASSIGNMENT (( #25545 ) ) ; +#49026 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82563, 'distance_accuracy_value', 'NONE'); +#49027 = STYLED_ITEM ( 'NONE', ( #15835 ), #44813 ) ; +#49028 = LINE ( 'NONE', #98397, #20559 ) ; +#49029 = PRESENTATION_STYLE_ASSIGNMENT (( #50053 ) ) ; +#49030 = SURFACE_STYLE_USAGE ( .BOTH. , #28064 ) ; +#49031 = PRESENTATION_STYLE_ASSIGNMENT (( #34228 ) ) ; +#49032 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49033 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#49034 = ORIENTED_EDGE ( 'NONE', *, *, #46011, .T. ) ; +#49035 = SURFACE_SIDE_STYLE ('',( #17854 ) ) ; +#49036 = EDGE_CURVE ( 'NONE', #52930, #13305, #6009, .T. ) ; +#49037 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #74726 ) ; +#49038 = FILL_AREA_STYLE ('',( #17855 ) ) ; +#49039 = EDGE_LOOP ( 'NONE', ( #32726, #44522, #3105, #85708 ) ) ; +#49040 = FILL_AREA_STYLE ('',( #33208 ) ) ; +#49041 = CIRCLE ( 'NONE', #76697, 0.09999999999999939493 ) ; +#49042 = VECTOR ( 'NONE', #94695, 1000.000000000000000 ) ; +#49043 = ORIENTED_EDGE ( 'NONE', *, *, #35747, .F. ) ; +#49044 = SURFACE_STYLE_FILL_AREA ( #70477 ) ; +#49045 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65341 ) ) ; +#49046 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79952 ), #31088 ) ; +#49047 = CARTESIAN_POINT ( 'NONE', ( -1.010461395130570095, -1.072184731453450057, 0.8100000000000000533 ) ) ; +#49048 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49049 = FILL_AREA_STYLE ('',( #88839 ) ) ; +#49050 = SURFACE_SIDE_STYLE ('',( #94956 ) ) ; +#49051 = CARTESIAN_POINT ( 'NONE', ( 6.106202875125043228, 9.368346875125045159, 0.8648700000000000276 ) ) ; +#49052 = FILL_AREA_STYLE_COLOUR ( '', #98488 ) ; +#49054 = VERTEX_POINT ( 'NONE', #99405 ) ; +#49053 = ORIENTED_EDGE ( 'NONE', *, *, #22591, .F. ) ; +#49055 = EDGE_CURVE ( 'NONE', #7232, #32337, #22390, .T. ) ; +#49056 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86493 ) ) ; +#49057 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70222 ) ) ; +#49058 = ORIENTED_EDGE ( 'NONE', *, *, #93161, .T. ) ; +#49059 = SURFACE_STYLE_FILL_AREA ( #65876 ) ; +#49061 = PRESENTATION_STYLE_ASSIGNMENT (( #17875 ) ) ; +#49060 = PRESENTATION_STYLE_ASSIGNMENT (( #57236 ) ) ; +#49062 = VERTEX_POINT ( 'NONE', #78035 ) ; +#49063 = EDGE_CURVE ( 'NONE', #46959, #78892, #47389, .T. ) ; +#49064 = ORIENTED_EDGE ( 'NONE', *, *, #69553, .T. ) ; +#49065 = VECTOR ( 'NONE', #68719, 1000.000000000000000 ) ; +#49066 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#49067 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#49068 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#49069 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#49070 = ORIENTED_EDGE ( 'NONE', *, *, #24893, .T. ) ; +#49071 = ORIENTED_EDGE ( 'NONE', *, *, #20478, .F. ) ; +#49072 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49073 = EDGE_LOOP ( 'NONE', ( #35334, #87625, #41525, #22447 ) ) ; +#49074 = EDGE_CURVE ( 'NONE', #46873, #98695, #85173, .T. ) ; +#49075 = EDGE_CURVE ( 'NONE', #11727, #92361, #93309, .T. ) ; +#49076 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49077 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86516 ), #71950 ) ; +#49078 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21272 ), #34371 ) ; +#49080 = EDGE_CURVE ( 'NONE', #90091, #78446, #39219, .T. ) ; +#49079 = ORIENTED_EDGE ( 'NONE', *, *, #92105, .T. ) ; +#49081 = EDGE_CURVE ( 'NONE', #90724, #1795, #23407, .T. ) ; +#49082 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49083 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4000000000000000222, 0.000000000000000000 ) ) ; +#49084 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49085 = VERTEX_POINT ( 'NONE', #69313 ) ; +#49086 = LINE ( 'NONE', #79726, #27312 ) ; +#49087 = FILL_AREA_STYLE_COLOUR ( '', #47664 ) ; +#49088 = ORIENTED_EDGE ( 'NONE', *, *, #86978, .F. ) ; +#49089 = LINE ( 'NONE', #72540, #61158 ) ; +#49090 = ADVANCED_FACE ( 'NONE', ( #54049 ), #55082, .T. ) ; +#49091 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#49093 = CIRCLE ( 'NONE', #65612, 0.009999999999999998473 ) ; +#49092 = LINE ( 'NONE', #25608, #93355 ) ; +#49094 = ADVANCED_FACE ( 'NONE', ( #91822 ), #21895, .T. ) ; +#49095 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49097 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.500000000000000444, 0.000000000000000000 ) ) ; +#49096 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#49098 = CARTESIAN_POINT ( 'NONE', ( 1.581953864252920283, -1.079063990458370093, 0.8299999999999990719 ) ) ; +#49099 = ORIENTED_EDGE ( 'NONE', *, *, #78609, .T. ) ; +#49100 = FILL_AREA_STYLE ('',( #32260 ) ) ; +#49101 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#49102 = ORIENTED_EDGE ( 'NONE', *, *, #65189, .T. ) ; +#49103 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96348 ), #63755 ) ; +#49104 = SURFACE_STYLE_USAGE ( .BOTH. , #25615 ) ; +#49105 = PLANE ( 'NONE', #57916 ) ; +#49106 = SURFACE_STYLE_FILL_AREA ( #63431 ) ; +#49107 = PRESENTATION_STYLE_ASSIGNMENT (( #80250 ) ) ; +#49108 = CARTESIAN_POINT ( 'NONE', ( 0.2757359312880713342, 0.8200000000000000622, 0.1378679656440356949 ) ) ; +#49110 = FILL_AREA_STYLE_COLOUR ( '', #76848 ) ; +#49109 = SURFACE_STYLE_FILL_AREA ( #19455 ) ; +#49111 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#49112 = AXIS2_PLACEMENT_3D ( 'NONE', #93045, #23159, #15455 ) ; +#49113 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49114 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49115 = STYLED_ITEM ( 'NONE', ( #54752 ), #86639 ) ; +#49116 = ORIENTED_EDGE ( 'NONE', *, *, #68077, .F. ) ; +#49117 = STYLED_ITEM ( 'NONE', ( #97177 ), #95583 ) ; +#49118 = FILL_AREA_STYLE ('',( #55768 ) ) ; +#49119 = SURFACE_SIDE_STYLE ('',( #93997 ) ) ; +#49120 = FILL_AREA_STYLE ('',( #25634 ) ) ; +#49121 = ADVANCED_FACE ( 'NONE', ( #87207 ), #95843, .T. ) ; +#49122 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31166 ) ) ; +#49123 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49124 = CIRCLE ( 'NONE', #63845, 0.009999999999999998473 ) ; +#49125 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506900000000080, 0.8648700000000000276 ) ) ; +#49126 = EDGE_CURVE ( 'NONE', #53395, #27995, #63746, .T. ) ; +#49127 = VERTEX_POINT ( 'NONE', #72894 ) ; +#49128 = PRESENTATION_STYLE_ASSIGNMENT (( #55289 ) ) ; +#49129 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56941, #88056, #47731, #78872, #9848, #64566, #8840, #757, #55922, #80405, #72726, #2787, #33952, #17074, #56441, #71211, #64074, #65071, #26289 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.827722729374921579E-05, 3.540061502004459648E-05, 5.176356202143433434E-05, 6.750299826528529995E-05, 8.273623489609373467E-05, 9.765522892530948079E-05, 0.0001124576626364706347, 0.0001272425831096937895, 0.0001422599913927652393, 0.0001573908365776010936, 0.0001730496430735188769, 0.0001892507387656465771, 0.0002057214521072078903, 0.0002222442170891137433, 0.0002388674796421553950, 0.0002555440932686103557 ), + .UNSPECIFIED. ) ; +#49130 = VECTOR ( 'NONE', #94084, 1000.000000000000000 ) ; +#49131 = PRESENTATION_STYLE_ASSIGNMENT (( #42950 ) ) ; +#49132 = PRESENTATION_STYLE_ASSIGNMENT (( #19478 ) ) ; +#49133 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#49134 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#49135 = VECTOR ( 'NONE', #42730, 1000.000000000000000 ) ; +#49136 = CIRCLE ( 'NONE', #47502, 0.2000000000000005107 ) ; +#49137 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#49138 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49139 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100379, 'distance_accuracy_value', 'NONE'); +#49140 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49141 = FILL_AREA_STYLE ('',( #31781 ) ) ; +#49142 = EDGE_LOOP ( 'NONE', ( #89347, #32363, #89267, #97610 ) ) ; +#49143 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49144 = ORIENTED_EDGE ( 'NONE', *, *, #21978, .F. ) ; +#49145 = FILL_AREA_STYLE ('',( #97566 ) ) ; +#49147 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41824, 'distance_accuracy_value', 'NONE'); +#49146 = VECTOR ( 'NONE', #95993, 1000.000000000000000 ) ; +#49148 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58559, 'distance_accuracy_value', 'NONE'); +#49149 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49150 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49151 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49152 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49153 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49154 = ORIENTED_EDGE ( 'NONE', *, *, #89343, .T. ) ; +#49155 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#49156 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49157 = EDGE_CURVE ( 'NONE', #78125, #44242, #2953, .T. ) ; +#49158 = PLANE ( 'NONE', #62408 ) ; +#49159 = ORIENTED_EDGE ( 'NONE', *, *, #24620, .T. ) ; +#49160 = LINE ( 'NONE', #34357, #32693 ) ; +#49161 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49162 = ORIENTED_EDGE ( 'NONE', *, *, #6867, .F. ) ; +#49163 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23065 ), #41073 ) ; +#49164 = SURFACE_STYLE_FILL_AREA ( #19506 ) ; +#49165 = FILL_AREA_STYLE_COLOUR ( '', #51174 ) ; +#49166 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999988828, -0.1400000000000000411 ) ) ; +#49167 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.149999999999970157, 0.000000000000000000 ) ) ; +#49168 = ORIENTED_EDGE ( 'NONE', *, *, #27545, .T. ) ; +#49169 = VECTOR ( 'NONE', #7365, 1000.000000000000000 ) ; +#49170 = LINE ( 'NONE', #95077, #24592 ) ; +#49171 = ORIENTED_EDGE ( 'NONE', *, *, #47202, .T. ) ; +#49172 = SURFACE_STYLE_USAGE ( .BOTH. , #87960 ) ; +#49173 = EDGE_LOOP ( 'NONE', ( #26967, #14476, #31543, #70453 ) ) ; +#49174 = CARTESIAN_POINT ( 'NONE', ( 1.662784294148539344, -1.164927051866627261, 0.8099999999999999423 ) ) ; +#49175 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#49176 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9926 ) ) ; +#49177 = FACE_OUTER_BOUND ( 'NONE', #26562, .T. ) ; +#49178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49179 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#49180 = VERTEX_POINT ( 'NONE', #40251 ) ; +#49182 = VERTEX_POINT ( 'NONE', #79557 ) ; +#49181 = EDGE_LOOP ( 'NONE', ( #92029, #64006, #53182, #95225 ) ) ; +#49183 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49184 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100929 ) ; +#49185 = ORIENTED_EDGE ( 'NONE', *, *, #10731, .T. ) ; +#49186 = AXIS2_PLACEMENT_3D ( 'NONE', #56014, #17160, #79492 ) ; +#49187 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#49188 = AXIS2_PLACEMENT_3D ( 'NONE', #78256, #84391, #86408 ) ; +#49189 = VECTOR ( 'NONE', #67237, 1000.000000000000114 ) ; +#49190 = VERTEX_POINT ( 'NONE', #71378 ) ; +#49192 = ORIENTED_EDGE ( 'NONE', *, *, #34912, .T. ) ; +#49191 = SURFACE_STYLE_USAGE ( .BOTH. , #78799 ) ; +#49193 = EDGE_CURVE ( 'NONE', #83746, #71728, #34119, .T. ) ; +#49194 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34353, #94569, #55807, #86945, #48139, #79279, #9240, #1687, #87014, #7968, #31041, #15693, #7471, #1423, #100357, #78019, #908, #30497, #62709 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.139749904431148539E-05, 4.167926570800450003E-05, 6.117642585279143739E-05, 8.007125617966778363E-05, 9.849555549675536334E-05, 0.0001164573492433767853, 0.0001342794739314012373, 0.0001521830310466221311, 0.0001701165620495521860, 0.0001883875854461628050, 0.0002070280353970009200, 0.0002264193111612982268, 0.0002460901620273280477, 0.0002661920138352033842, 0.0002865739416040863504, 0.0003074733952738241990 ), + .UNSPECIFIED. ) ; +#49195 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 2.299999999999999822, 0.000000000000000000 ) ) ; +#49197 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#49196 = LINE ( 'NONE', #32359, #67239 ) ; +#49198 = SURFACE_STYLE_FILL_AREA ( #43017 ) ; +#49199 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000011380, -0.1499999999999999944 ) ) ; +#49200 = EDGE_LOOP ( 'NONE', ( #2936, #64153, #90027, #15708 ) ) ; +#49201 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.476179938779914824, -0.02000000000000000042 ) ) ; +#49202 = LINE ( 'NONE', #94616, #100406 ) ; +#49203 = ORIENTED_EDGE ( 'NONE', *, *, #9677, .T. ) ; +#49204 = MANIFOLD_SOLID_BREP ( 'ÊäÈë152', #81167 ) ; +#49205 = FACE_OUTER_BOUND ( 'NONE', #18012, .T. ) ; +#49206 = SURFACE_STYLE_FILL_AREA ( #79335 ) ; +#49207 = ORIENTED_EDGE ( 'NONE', *, *, #15175, .F. ) ; +#49208 = AXIS2_PLACEMENT_3D ( 'NONE', #54141, #84278, #68916 ) ; +#49209 = PLANE ( 'NONE', #14346 ) ; +#49210 = CARTESIAN_POINT ( 'NONE', ( 0.03349564727623650928, -1.152628822534790043, 0.8300000000000002931 ) ) ; +#49211 = ADVANCED_FACE ( 'NONE', ( #82574 ), #88708, .F. ) ; +#49213 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#49212 = FILL_AREA_STYLE_COLOUR ( '', #59419 ) ; +#49214 = SURFACE_STYLE_FILL_AREA ( #46256 ) ; +#49215 = LINE ( 'NONE', #56400, #52324 ) ; +#49216 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93168 ) ) ; +#49217 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49218 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49219 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#49220 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81811 ), #11795 ) ; +#49221 = LINE ( 'NONE', #2754, #78965 ) ; +#49222 = STYLED_ITEM ( 'NONE', ( #64073 ), #51958 ) ; +#49223 = PLANE ( 'NONE', #71932 ) ; +#49224 = ORIENTED_EDGE ( 'NONE', *, *, #78346, .F. ) ; +#49225 = PRESENTATION_STYLE_ASSIGNMENT (( #31875 ) ) ; +#49226 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#49227 = FILL_AREA_STYLE ('',( #73703 ) ) ; +#49228 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49229 = ORIENTED_EDGE ( 'NONE', *, *, #30946, .T. ) ; +#49230 = EDGE_CURVE ( 'NONE', #83639, #63500, #46131, .T. ) ; +#49231 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#49232 = FILL_AREA_STYLE_COLOUR ( '', #7260 ) ; +#49235 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.500000000000000000, 1.869351947278245041E-79 ) ) ; +#49234 = LINE ( 'NONE', #17048, #57178 ) ; +#49233 = FILL_AREA_STYLE ('',( #41078 ) ) ; +#49236 = CARTESIAN_POINT ( 'NONE', ( 1.571641772371880297, -1.354501511147599979, 0.8099999999999984990 ) ) ; +#49237 = SURFACE_STYLE_USAGE ( .BOTH. , #89545 ) ; +#49238 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8299999999999999600 ) ) ; +#49239 = DIRECTION ( 'NONE', ( -0.7071075504167445569, 0.7071060119555137025, 0.000000000000000000 ) ) ; +#49240 = EDGE_CURVE ( 'NONE', #88228, #97804, #71676, .T. ) ; +#49241 = EDGE_LOOP ( 'NONE', ( #71935, #89927, #7614, #45012 ) ) ; +#49242 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49243 = PRESENTATION_STYLE_ASSIGNMENT (( #96172 ) ) ; +#49244 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#49245 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.5000000000000000000, -13.40000000000000036 ) ) ; +#49246 = STYLED_ITEM ( 'NONE', ( #98915 ), #34096 ) ; +#49247 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49248 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49249 = PLANE ( 'NONE', #75156 ) ; +#49250 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#49251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49252 = STYLED_ITEM ( 'NONE', ( #48727 ), #87064 ) ; +#49254 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41102 ) ) ; +#49253 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#49255 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78868, 'distance_accuracy_value', 'NONE'); +#49256 = VECTOR ( 'NONE', #31029, 1000.000000000000000 ) ; +#49257 = FACE_OUTER_BOUND ( 'NONE', #32614, .T. ) ; +#49258 = LINE ( 'NONE', #41601, #56755 ) ; +#49259 = PRESENTATION_STYLE_ASSIGNMENT (( #3292 ) ) ; +#49260 = DIRECTION ( 'NONE', ( -0.7071067811865479058, 0.7071067811865470176, 0.000000000000000000 ) ) ; +#49261 = ORIENTED_EDGE ( 'NONE', *, *, #51320, .F. ) ; +#49262 = VERTEX_POINT ( 'NONE', #4436 ) ; +#49263 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97450, 'distance_accuracy_value', 'NONE'); +#49264 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27264, 'distance_accuracy_value', 'NONE'); +#49265 = MANIFOLD_SOLID_BREP ( 'ÊäÈë82', #93985 ) ; +#49266 = FILL_AREA_STYLE ('',( #15685 ) ) ; +#49267 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36223 ) ) ; +#49268 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49269 = CARTESIAN_POINT ( 'NONE', ( -1.166666666666666741, -3.500000000000000000, 0.000000000000000000 ) ) ; +#49270 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#49271 = FILL_AREA_STYLE_COLOUR ( '', #2020 ) ; +#49272 = EDGE_LOOP ( 'NONE', ( #51584, #13418, #58366, #7925 ) ) ; +#49273 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49274 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10802, 'distance_accuracy_value', 'NONE'); +#49275 = SURFACE_STYLE_FILL_AREA ( #56963 ) ; +#49276 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49277 = VECTOR ( 'NONE', #72349, 1000.000000000000000 ) ; +#49278 = ORIENTED_EDGE ( 'NONE', *, *, #22077, .T. ) ; +#49279 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49280 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49281 = FILL_AREA_STYLE_COLOUR ( '', #5331 ) ; +#49282 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49283 = PRESENTATION_STYLE_ASSIGNMENT (( #73766 ) ) ; +#49284 = EDGE_LOOP ( 'NONE', ( #80986, #60989, #92726, #74516, #40242, #21100 ) ) ; +#49285 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49286 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66918, 'distance_accuracy_value', 'NONE'); +#49287 = FILL_AREA_STYLE_COLOUR ( '', #58960 ) ; +#49288 = VECTOR ( 'NONE', #8237, 1000.000000000000000 ) ; +#49289 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#49290 = EDGE_CURVE ( 'NONE', #96999, #22523, #77812, .T. ) ; +#49291 = ORIENTED_EDGE ( 'NONE', *, *, #16559, .T. ) ; +#49292 = EDGE_CURVE ( 'NONE', #24588, #55259, #58613, .T. ) ; +#49293 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 9.801187639268928344E-18, 1.000000000000000000 ) ) ; +#49294 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49295 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64010 ), #77040 ) ; +#49296 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49297 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#49298 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49299 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#49300 = STYLED_ITEM ( 'NONE', ( #46746 ), #82035 ) ; +#49301 = STYLED_ITEM ( 'NONE', ( #44002 ), #45789 ) ; +#49302 = VERTEX_POINT ( 'NONE', #90213 ) ; +#49303 = EDGE_LOOP ( 'NONE', ( #88129, #72921, #46643, #18879 ) ) ; +#49304 = EDGE_CURVE ( 'NONE', #89125, #81105, #4921, .T. ) ; +#49306 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#49305 = PLANE ( 'NONE', #37807 ) ; +#49307 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49308 = PRESENTATION_STYLE_ASSIGNMENT (( #18117 ) ) ; +#49309 = ORIENTED_EDGE ( 'NONE', *, *, #36860, .F. ) ; +#49310 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, 0.2349999999999999867 ) ) ; +#49311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49312 = VERTEX_POINT ( 'NONE', #67225 ) ; +#49314 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#49313 = LINE ( 'NONE', #9904, #32490 ) ; +#49315 = ORIENTED_EDGE ( 'NONE', *, *, #85614, .F. ) ; +#49316 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49317 = ORIENTED_EDGE ( 'NONE', *, *, #99091, .F. ) ; +#49318 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100250 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95015, #41452, #2638 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49319 = EDGE_CURVE ( 'NONE', #23290, #38846, #90720, .T. ) ; +#49321 = LINE ( 'NONE', #56512, #98782 ) ; +#49320 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#49322 = LINE ( 'NONE', #11431, #44131 ) ; +#49323 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49324 = ORIENTED_EDGE ( 'NONE', *, *, #31581, .T. ) ; +#49325 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62314 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98365, #3014, #96911 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49326 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49327 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49328 = ORIENTED_EDGE ( 'NONE', *, *, #36981, .T. ) ; +#49329 = CARTESIAN_POINT ( 'NONE', ( 1.363204453251209980, -1.351484773706350007, 0.8100000000000000533 ) ) ; +#49330 = SURFACE_STYLE_FILL_AREA ( #79481 ) ; +#49331 = ORIENTED_EDGE ( 'NONE', *, *, #51629, .F. ) ; +#49332 = SURFACE_SIDE_STYLE ('',( #33526 ) ) ; +#49334 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8991599999999999593 ) ) ; +#49333 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49335 = CARTESIAN_POINT ( 'NONE', ( -1.282612376779509900, -1.188596174736179956, 0.8100000000000000533 ) ) ; +#49336 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49337 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15087 ) ) ; +#49338 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49339 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#49340 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#49341 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#49342 = CARTESIAN_POINT ( 'NONE', ( 1.286377402956589977, -0.9766832120545909657, 0.8100000000000000533 ) ) ; +#49343 = AXIS2_PLACEMENT_3D ( 'NONE', #45441, #82791, #44454 ) ; +#49344 = ORIENTED_EDGE ( 'NONE', *, *, #99281, .F. ) ; +#49345 = EDGE_CURVE ( 'NONE', #49312, #64618, #13033, .T. ) ; +#49346 = AXIS2_PLACEMENT_3D ( 'NONE', #37886, #62903, #100051 ) ; +#49347 = FACE_OUTER_BOUND ( 'NONE', #62981, .T. ) ; +#49348 = SURFACE_STYLE_FILL_AREA ( #66660 ) ; +#49349 = FILL_AREA_STYLE ('',( #57046 ) ) ; +#49350 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -1.224646799147353207E-16 ) ) ; +#49351 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -1.099999999999999867, 0.1829999999999620541 ) ) ; +#49352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64005 ) ) ; +#49353 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 1.474514954580256140E-18, 0.8499999999999999778 ) ) ; +#49354 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49355 = EDGE_CURVE ( 'NONE', #9513, #11284, #44239, .T. ) ; +#49356 = ORIENTED_EDGE ( 'NONE', *, *, #12789, .F. ) ; +#49357 = MANIFOLD_SOLID_BREP ( 'ÊäÈë107', #95905 ) ; +#49358 = PLANE ( 'NONE', #24944 ) ; +#49359 = SURFACE_SIDE_STYLE ('',( #33029 ) ) ; +#49360 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20043 ), #96695 ) ; +#49361 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49362 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49363 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49364 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18412, 'distance_accuracy_value', 'NONE'); +#49365 = SURFACE_STYLE_FILL_AREA ( #57063 ) ; +#49366 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49367 = LINE ( 'NONE', #96303, #24020 ) ; +#49368 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#49369 = FACE_OUTER_BOUND ( 'NONE', #17728, .T. ) ; +#49370 = STYLED_ITEM ( 'NONE', ( #87627 ), #75783 ) ; +#49371 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#49372 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49373 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.300000000000000266, 0.1829999999999580573 ) ) ; +#49374 = FACE_OUTER_BOUND ( 'NONE', #684, .T. ) ; +#49375 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#49376 = AXIS2_PLACEMENT_3D ( 'NONE', #18193, #81047, #10981 ) ; +#49377 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#49378 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #89325, 'design' ) ; +#49379 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#49380 = SURFACE_STYLE_FILL_AREA ( #65707 ) ; +#49381 = EDGE_LOOP ( 'NONE', ( #49926, #42797, #12832, #3649, #81591, #72656, #61844, #19182 ) ) ; +#49382 = LINE ( 'NONE', #42724, #66602 ) ; +#49383 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49384 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13606, 'distance_accuracy_value', 'NONE'); +#49385 = VECTOR ( 'NONE', #37114, 1000.000000000000000 ) ; +#49386 = VECTOR ( 'NONE', #52749, 1000.000000000000000 ) ; +#49387 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36900, 'distance_accuracy_value', 'NONE'); +#49388 = STYLED_ITEM ( 'NONE', ( #85745 ), #35007 ) ; +#49389 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49390 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67295 ), #386 ) ; +#49391 = ADVANCED_FACE ( 'NONE', ( #14066 ), #54454, .F. ) ; +#49392 = EDGE_CURVE ( 'NONE', #74437, #94230, #62126, .T. ) ; +#49393 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49394 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49395 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.3000000000000005995, 0.1829999999999710192 ) ) ; +#49396 = LINE ( 'NONE', #96321, #81036 ) ; +#49397 = VERTEX_POINT ( 'NONE', #60608 ) ; +#49398 = AXIS2_PLACEMENT_3D ( 'NONE', #73047, #34271, #65368 ) ; +#49399 = PRESENTATION_STYLE_ASSIGNMENT (( #86164 ) ) ; +#49400 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44716, 'distance_accuracy_value', 'NONE'); +#49401 = FACE_OUTER_BOUND ( 'NONE', #677, .T. ) ; +#49402 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95769, 'distance_accuracy_value', 'NONE'); +#49403 = SURFACE_STYLE_FILL_AREA ( #94320 ) ; +#49404 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49405 = EDGE_CURVE ( 'NONE', #85319, #70873, #62624, .T. ) ; +#49406 = ORIENTED_EDGE ( 'NONE', *, *, #39178, .F. ) ; +#49407 = VERTEX_POINT ( 'NONE', #93185 ) ; +#49408 = EDGE_CURVE ( 'NONE', #19702, #19409, #85563, .T. ) ; +#49409 = FILL_AREA_STYLE ('',( #41750 ) ) ; +#49410 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#49411 = AXIS2_PLACEMENT_3D ( 'NONE', #38095, #100737, #47251 ) ; +#49412 = ORIENTED_EDGE ( 'NONE', *, *, #58817, .F. ) ; +#49413 = DIRECTION ( 'NONE', ( -0.7071060119555140355, 0.7071075504167442238, 0.000000000000000000 ) ) ; +#49414 = EDGE_CURVE ( 'NONE', #65783, #49717, #46743, .T. ) ; +#49415 = SURFACE_STYLE_FILL_AREA ( #64723 ) ; +#49416 = PRODUCT_CONTEXT ( 'NONE', #42369, 'mechanical' ) ; +#49417 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49418 = FILL_AREA_STYLE ('',( #9525 ) ) ; +#49420 = VERTEX_POINT ( 'NONE', #6391 ) ; +#49419 = ORIENTED_EDGE ( 'NONE', *, *, #60086, .T. ) ; +#49421 = STYLED_ITEM ( 'NONE', ( #54620 ), #70630 ) ; +#49422 = EDGE_LOOP ( 'NONE', ( #94739, #10641, #48527, #28447 ) ) ; +#49423 = EDGE_LOOP ( 'NONE', ( #29742, #11745, #29803, #16148, #73433, #2344 ) ) ; +#49424 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#49425 = ADVANCED_FACE ( 'NONE', ( #39109 ), #93683, .T. ) ; +#49426 = LINE ( 'NONE', #11024, #89779 ) ; +#49428 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999578 ) ) ; +#49427 = SURFACE_STYLE_FILL_AREA ( #95341 ) ; +#49429 = EDGE_LOOP ( 'NONE', ( #92927, #58384, #64148, #948 ) ) ; +#49430 = STYLED_ITEM ( 'NONE', ( #66842 ), #53014 ) ; +#49431 = ADVANCED_FACE ( 'NONE', ( #65110 ), #25335, .T. ) ; +#49432 = VERTEX_POINT ( 'NONE', #32472 ) ; +#49433 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49434 = ORIENTED_EDGE ( 'NONE', *, *, #59877, .F. ) ; +#49436 = FILL_AREA_STYLE_COLOUR ( '', #77196 ) ; +#49435 = LINE ( 'NONE', #70906, #74823 ) ; +#49437 = VECTOR ( 'NONE', #49842, 1000.000000000000000 ) ; +#49438 = VERTEX_POINT ( 'NONE', #95715 ) ; +#49439 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59316 ) ) ; +#49440 = ORIENTED_EDGE ( 'NONE', *, *, #67196, .T. ) ; +#49441 = EDGE_CURVE ( 'NONE', #59417, #9822, #31961, .T. ) ; +#49442 = SURFACE_STYLE_FILL_AREA ( #88250 ) ; +#49443 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49444 = ADVANCED_FACE ( 'NONE', ( #72779 ), #71255, .T. ) ; +#49445 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71744 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61531, #60529, #14979 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49446 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49447 = ORIENTED_EDGE ( 'NONE', *, *, #9543, .T. ) ; +#49448 = PRESENTATION_STYLE_ASSIGNMENT (( #18264 ) ) ; +#49449 = VERTEX_POINT ( 'NONE', #44129 ) ; +#49450 = EDGE_CURVE ( 'NONE', #13508, #2385, #55975, .T. ) ; +#49451 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49452 = STYLED_ITEM ( 'NONE', ( #53638 ), #35947 ) ; +#49453 = ORIENTED_EDGE ( 'NONE', *, *, #47344, .F. ) ; +#49454 = CARTESIAN_POINT ( 'NONE', ( 0.05204425658606930821, -1.220010286732279958, 0.8299999999999999600 ) ) ; +#49455 = ORIENTED_EDGE ( 'NONE', *, *, #94002, .T. ) ; +#49456 = EDGE_LOOP ( 'NONE', ( #28480, #27299, #48020, #42626, #19888, #74780 ) ) ; +#49457 = VECTOR ( 'NONE', #75755, 1000.000000000000000 ) ; +#49459 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49458 = PRODUCT_DEFINITION ( 'δ֪', '', #37237, #100347 ) ; +#49460 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49461 = VECTOR ( 'NONE', #39994, 1000.000000000000000 ) ; +#49462 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23364 ) ) ; +#49463 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34761 ), #51084 ) ; +#49464 = PLANE ( 'NONE', #46533 ) ; +#49465 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.9000000000000007994, -0.02000000000000000042 ) ) ; +#49466 = VECTOR ( 'NONE', #57666, 1000.000000000000000 ) ; +#49467 = SURFACE_SIDE_STYLE ('',( #9560 ) ) ; +#49468 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94754, #78454, #14616, #53480 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#49469 = VECTOR ( 'NONE', #16198, 1000.000000000000000 ) ; +#49470 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#49471 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49472 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49473 = ORIENTED_EDGE ( 'NONE', *, *, #43199, .F. ) ; +#49474 = EDGE_CURVE ( 'NONE', #81075, #54723, #27844, .T. ) ; +#49475 = PRESENTATION_STYLE_ASSIGNMENT (( #57155 ) ) ; +#49476 = ORIENTED_EDGE ( 'NONE', *, *, #54673, .T. ) ; +#49477 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93442 ) ) ; +#49478 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49479 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#49480 = VECTOR ( 'NONE', #82402, 1000.000000000000000 ) ; +#49481 = LINE ( 'NONE', #42325, #92056 ) ; +#49482 = VECTOR ( 'NONE', #18259, 1000.000000000000000 ) ; +#49483 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49484 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49485 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49486 = EDGE_CURVE ( 'NONE', #56475, #50459, #36500, .T. ) ; +#49487 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.500000000000000222, -0.02000000000000839995 ) ) ; +#49488 = LINE ( 'NONE', #3015, #76518 ) ; +#49489 = SURFACE_SIDE_STYLE ('',( #1000 ) ) ; +#49490 = LINE ( 'NONE', #70175, #37910 ) ; +#49491 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#49492 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47097 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100614, #38972, #92554 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49493 = DIRECTION ( 'NONE', ( -0.7071067811865445751, 0.7071067811865504593, 0.000000000000000000 ) ) ; +#49494 = FACE_OUTER_BOUND ( 'NONE', #66603, .T. ) ; +#49495 = EDGE_CURVE ( 'NONE', #95875, #65615, #97708, .T. ) ; +#49496 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1500000000000000222 ) ) ; +#49497 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49498 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#49499 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666627084, -2.700000000000000178, 3.495651678169879387E-76 ) ) ; +#49500 = PLANE ( 'NONE', #29142 ) ; +#49501 = EDGE_CURVE ( 'NONE', #74773, #94479, #26330, .T. ) ; +#49502 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49503 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000020040, 0.1829999999999709914 ) ) ; +#49504 = SURFACE_STYLE_FILL_AREA ( #65825 ) ; +#49505 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49506 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91809, 'distance_accuracy_value', 'NONE'); +#49507 = ORIENTED_EDGE ( 'NONE', *, *, #38449, .F. ) ; +#49508 = CARTESIAN_POINT ( 'NONE', ( 1.654345427547579961, -0.9032194100038879458, 0.8100000000000000533 ) ) ; +#49509 = ORIENTED_EDGE ( 'NONE', *, *, #33246, .T. ) ; +#49510 = LINE ( 'NONE', #41846, #38802 ) ; +#49511 = CARTESIAN_POINT ( 'NONE', ( -0.7486876120449308392, 1.376287671486961850, 0.8100000000000000533 ) ) ; +#49512 = PLANE ( 'NONE', #12089 ) ; +#49513 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49514 = STYLED_ITEM ( 'NONE', ( #48231 ), #88144 ) ; +#49515 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49516 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36472 ) ) ; +#49517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89662 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88965, #51180, #81332 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49518 = EDGE_CURVE ( 'NONE', #75277, #90613, #80196, .T. ) ; +#49519 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49520 = ORIENTED_EDGE ( 'NONE', *, *, #32971, .F. ) ; +#49521 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40103 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22454, #28613, #38295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49522 = ORIENTED_EDGE ( 'NONE', *, *, #27158, .T. ) ; +#49523 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#49524 = SURFACE_SIDE_STYLE ('',( #18340 ) ) ; +#49525 = FILL_AREA_STYLE_COLOUR ( '', #13715 ) ; +#49526 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#49527 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#49528 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#49529 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36486 ), #26724 ) ; +#49530 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98335 ), #96711 ) ; +#49531 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49532 = SURFACE_STYLE_USAGE ( .BOTH. , #18347 ) ; +#49533 = ORIENTED_EDGE ( 'NONE', *, *, #83135, .T. ) ; +#49534 = STYLED_ITEM ( 'NONE', ( #65689 ), #21348 ) ; +#49535 = PRESENTATION_STYLE_ASSIGNMENT (( #89821 ) ) ; +#49536 = MANIFOLD_SOLID_BREP ( 'ÊäÈë128', #71296 ) ; +#49537 = ORIENTED_EDGE ( 'NONE', *, *, #636, .F. ) ; +#49538 = EDGE_CURVE ( 'NONE', #26361, #25572, #12410, .T. ) ; +#49540 = STYLED_ITEM ( 'NONE', ( #70808 ), #28656 ) ; +#49539 = AXIS2_PLACEMENT_3D ( 'NONE', #34376, #82335, #19523 ) ; +#49541 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86754 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10563, #87777, #49485 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49542 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58467 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66185, #65681, #27390 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49543 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#49544 = ORIENTED_EDGE ( 'NONE', *, *, #23002, .T. ) ; +#49545 = LINE ( 'NONE', #10620, #34690 ) ; +#49546 = SURFACE_STYLE_FILL_AREA ( #10113 ) ; +#49547 = VECTOR ( 'NONE', #3511, 1000.000000000000000 ) ; +#49548 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#49549 = FILL_AREA_STYLE_COLOUR ( '', #1027 ) ; +#49550 = STYLED_ITEM ( 'NONE', ( #66847 ), #37287 ) ; +#49551 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69072 ) ) ; +#49552 = DIRECTION ( 'NONE', ( -1.836909530733570078E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49553 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#49554 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999556, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#49555 = SURFACE_STYLE_USAGE ( .BOTH. , #18364 ) ; +#49557 = ORIENTED_EDGE ( 'NONE', *, *, #28143, .F. ) ; +#49556 = EDGE_LOOP ( 'NONE', ( #7524, #43132, #92187, #83708 ) ) ; +#49558 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#49559 = AXIS2_PLACEMENT_3D ( 'NONE', #63937, #95032, #30742 ) ; +#49560 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#49561 = ORIENTED_EDGE ( 'NONE', *, *, #81676, .T. ) ; +#49562 = PRESENTATION_STYLE_ASSIGNMENT (( #97478 ) ) ; +#49563 = VECTOR ( 'NONE', #26356, 1000.000000000000114 ) ; +#49565 = FACE_OUTER_BOUND ( 'NONE', #26580, .T. ) ; +#49564 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#49566 = VERTEX_POINT ( 'NONE', #4814 ) ; +#49567 = ORIENTED_EDGE ( 'NONE', *, *, #73051, .F. ) ; +#49568 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#49569 = SURFACE_SIDE_STYLE ('',( #63395 ) ) ; +#49570 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49571 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.7499999999941607820, 0.6999285677797779659 ) ) ; +#49572 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49573 = LINE ( 'NONE', #56744, #17111 ) ; +#49574 = PLANE ( 'NONE', #80134 ) ; +#49575 = VERTEX_POINT ( 'NONE', #51815 ) ; +#49576 = ORIENTED_EDGE ( 'NONE', *, *, #39217, .F. ) ; +#49577 = LINE ( 'NONE', #80723, #27468 ) ; +#49578 = ORIENTED_EDGE ( 'NONE', *, *, #98068, .T. ) ; +#49579 = FILL_AREA_STYLE_COLOUR ( '', #95358 ) ; +#49580 = ADVANCED_FACE ( 'NONE', ( #67108 ), #50342, .T. ) ; +#49582 = ORIENTED_EDGE ( 'NONE', *, *, #73402, .F. ) ; +#49581 = FILL_AREA_STYLE ('',( #71030 ) ) ; +#49583 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49584 = FILL_AREA_STYLE ('',( #96497 ) ) ; +#49585 = SURFACE_SIDE_STYLE ('',( #18402 ) ) ; +#49586 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49587 = ORIENTED_EDGE ( 'NONE', *, *, #21093, .F. ) ; +#49588 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49589 = LINE ( 'NONE', #63893, #24889 ) ; +#49590 = ORIENTED_EDGE ( 'NONE', *, *, #10030, .F. ) ; +#49591 = LINE ( 'NONE', #81251, #35073 ) ; +#49592 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#49593 = FACE_OUTER_BOUND ( 'NONE', #38966, .T. ) ; +#49594 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#49595 = VECTOR ( 'NONE', #93802, 1000.000000000000000 ) ; +#49596 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8648700000000000276 ) ) ; +#49597 = SURFACE_SIDE_STYLE ('',( #2619 ) ) ; +#49599 = FACE_OUTER_BOUND ( 'NONE', #90759, .T. ) ; +#49598 = SURFACE_STYLE_USAGE ( .BOTH. , #98464 ) ; +#49600 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8648700000000000276 ) ) ; +#49601 = ORIENTED_EDGE ( 'NONE', *, *, #73805, .F. ) ; +#49602 = CARTESIAN_POINT ( 'NONE', ( 1.525795062450169937, -1.430103682213279992, 0.8099999999999982769 ) ) ; +#49603 = AXIS2_PLACEMENT_3D ( 'NONE', #62553, #100688, #84984 ) ; +#49604 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#49605 = ORIENTED_EDGE ( 'NONE', *, *, #3306, .F. ) ; +#49606 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49607 = SURFACE_STYLE_FILL_AREA ( #33783 ) ; +#49608 = MANIFOLD_SOLID_BREP ( 'ÊäÈë116', #33936 ) ; +#49609 = CARTESIAN_POINT ( 'NONE', ( -0.5282008442508040469, -1.258308808185959915, 0.8300000000000000711 ) ) ; +#49610 = AXIS2_PLACEMENT_3D ( 'NONE', #77476, #8454, #17198 ) ; +#49611 = FILL_AREA_STYLE_COLOUR ( '', #94156 ) ; +#49612 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2784314575050770846, 0.1458578643762690474 ) ) ; +#49613 = STYLED_ITEM ( 'NONE', ( #66076 ), #21491 ) ; +#49614 = CARTESIAN_POINT ( 'NONE', ( 1.799876578750339906, -1.066767002799750008, 0.8299999999999999600 ) ) ; +#49616 = ADVANCED_FACE ( 'NONE', ( #5795 ), #84932, .T. ) ; +#49615 = SURFACE_STYLE_USAGE ( .BOTH. , #56788 ) ; +#49617 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49618 = FILL_AREA_STYLE_COLOUR ( '', #80248 ) ; +#49619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8752 ) ) ; +#49620 = VECTOR ( 'NONE', #8300, 1000.000000000000000 ) ; +#49621 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.300000000000000044, 0.000000000000000000 ) ) ; +#49622 = VECTOR ( 'NONE', #100011, 1000.000000000000000 ) ; +#49623 = VERTEX_POINT ( 'NONE', #46099 ) ; +#49624 = SURFACE_STYLE_USAGE ( .BOTH. , #18437 ) ; +#49625 = FILL_AREA_STYLE_COLOUR ( '', #81588 ) ; +#49626 = ADVANCED_FACE ( 'NONE', ( #85443 ), #7256, .T. ) ; +#49627 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49628 = VECTOR ( 'NONE', #17375, 1000.000000000000000 ) ; +#49629 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15301 ) ) ; +#49630 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49632 = EDGE_CURVE ( 'NONE', #2623, #78820, #8262, .T. ) ; +#49631 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20536, 'distance_accuracy_value', 'NONE'); +#49633 = ORIENTED_EDGE ( 'NONE', *, *, #73273, .F. ) ; +#49634 = CARTESIAN_POINT ( 'NONE', ( 7.661838000000000370, 2.155857000000000134, 0.8991599999999999593 ) ) ; +#49635 = CARTESIAN_POINT ( 'NONE', ( -1.129230981225310071, -0.9561532343638800002, 0.8299999999999999600 ) ) ; +#49636 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#49637 = PRESENTATION_STYLE_ASSIGNMENT (( #26658 ) ) ; +#49638 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#49639 = FILL_AREA_STYLE_COLOUR ( '', #41665 ) ; +#49640 = STYLED_ITEM ( 'NONE', ( #34740 ), #67991 ) ; +#49641 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49642 = CARTESIAN_POINT ( 'NONE', ( -1.002767861914739989, -1.390055052842650074, 0.8300000000000001821 ) ) ; +#49643 = EDGE_CURVE ( 'NONE', #81132, #56911, #1180, .T. ) ; +#49644 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#49645 = EDGE_CURVE ( 'NONE', #22015, #82922, #33367, .T. ) ; +#49646 = LINE ( 'NONE', #5126, #19235 ) ; +#49647 = VERTEX_POINT ( 'NONE', #54836 ) ; +#49648 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49649 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17027 ) ) ; +#49650 = EDGE_LOOP ( 'NONE', ( #83966, #78059, #14659, #99412, #19193, #82845, #24572, #78712, #44443, #56570, #20366, #77624, #23016, #21922, #38025, #97920, #70897, #46904, #8498 ) ) ; +#49651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72264, 'distance_accuracy_value', 'NONE'); +#49652 = EDGE_CURVE ( 'NONE', #37825, #60527, #46621, .T. ) ; +#49653 = EDGE_CURVE ( 'NONE', #33332, #49054, #63993, .T. ) ; +#49654 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49656 = CARTESIAN_POINT ( 'NONE', ( 0.5449963026571937874, -1.098122393001198072, 0.8100000000000002753 ) ) ; +#49657 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#49658 = STYLED_ITEM ( 'NONE', ( #63384 ), #53543 ) ; +#49659 = FACE_OUTER_BOUND ( 'NONE', #49422, .T. ) ; +#49660 = LINE ( 'NONE', #64465, #38020 ) ; +#49661 = VERTEX_POINT ( 'NONE', #95597 ) ; +#49662 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49663 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#49664 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#49665 = ORIENTED_EDGE ( 'NONE', *, *, #50866, .T. ) ; +#49666 = SURFACE_STYLE_FILL_AREA ( #97080 ) ; +#49667 = AXIS2_PLACEMENT_3D ( 'NONE', #65404, #5106, #42934 ) ; +#49668 = ADVANCED_FACE ( 'NONE', ( #25703 ), #87471, .T. ) ; +#49669 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 4.524664999999999715, 0.8991599999999999593 ) ) ; +#49670 = ORIENTED_EDGE ( 'NONE', *, *, #44912, .T. ) ; +#49671 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#49672 = ADVANCED_FACE ( 'NONE', ( #2217 ), #93562, .T. ) ; +#49673 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -3.500000000000000444, 0.000000000000000000 ) ) ; +#49674 = PLANE ( 'NONE', #93477 ) ; +#49675 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49676 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49677 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33342 ), #38285 ) ; +#49678 = LINE ( 'NONE', #11755, #8996 ) ; +#49679 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49680 = ORIENTED_EDGE ( 'NONE', *, *, #28410, .F. ) ; +#49681 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.876179938779915179, -0.02000000000000000042 ) ) ; +#49682 = FILL_AREA_STYLE ('',( #79810 ) ) ; +#49683 = ORIENTED_EDGE ( 'NONE', *, *, #29999, .F. ) ; +#49684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49685 = VECTOR ( 'NONE', #40821, 1000.000000000000000 ) ; +#49686 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78571 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24796, #17077, #71729 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49687 = VECTOR ( 'NONE', #20476, 1000.000000000000000 ) ; +#49688 = SURFACE_STYLE_FILL_AREA ( #48675 ) ; +#49689 = VERTEX_POINT ( 'NONE', #49702 ) ; +#49692 = AXIS2_PLACEMENT_3D ( 'NONE', #70925, #1490, #38766 ) ; +#49691 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49690 = SURFACE_STYLE_FILL_AREA ( #1712 ) ; +#49693 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49694 = VECTOR ( 'NONE', #63694, 1000.000000000000000 ) ; +#49695 = CARTESIAN_POINT ( 'NONE', ( -0.4517732017275800094, -1.126314109036339994, 0.8299999999999999600 ) ) ; +#49696 = SURFACE_STYLE_USAGE ( .BOTH. , #36367 ) ; +#49698 = FACE_OUTER_BOUND ( 'NONE', #47494, .T. ) ; +#49697 = SURFACE_STYLE_FILL_AREA ( #88982 ) ; +#49699 = ORIENTED_EDGE ( 'NONE', *, *, #96738, .F. ) ; +#49701 = ORIENTED_EDGE ( 'NONE', *, *, #84339, .T. ) ; +#49700 = ORIENTED_EDGE ( 'NONE', *, *, #71357, .F. ) ; +#49702 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#49703 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8758 ) ) ; +#49704 = VERTEX_POINT ( 'NONE', #80841 ) ; +#49705 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74174 ), #52970 ) ; +#49706 = PLANE ( 'NONE', #67129 ) ; +#49707 = ADVANCED_FACE ( 'NONE', ( #33877 ), #43506, .F. ) ; +#49708 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46414 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77918, #79451, #38613 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49709 = ORIENTED_EDGE ( 'NONE', *, *, #36551, .F. ) ; +#49710 = EDGE_LOOP ( 'NONE', ( #35823, #26791, #96972, #91996 ) ) ; +#49711 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36654 ) ) ; +#49712 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#49714 = SURFACE_STYLE_USAGE ( .BOTH. , #32862 ) ; +#49713 = SURFACE_STYLE_FILL_AREA ( #44875 ) ; +#49715 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, 0.000000000000000000 ) ) ; +#49716 = SURFACE_STYLE_FILL_AREA ( #41044 ) ; +#49717 = VERTEX_POINT ( 'NONE', #74681 ) ; +#49719 = EDGE_CURVE ( 'NONE', #84706, #100686, #26215, .T. ) ; +#49718 = LINE ( 'NONE', #33891, #24424 ) ; +#49720 = SURFACE_SIDE_STYLE ('',( #88493 ) ) ; +#49721 = VERTEX_POINT ( 'NONE', #88478 ) ; +#49722 = PLANE ( 'NONE', #69342 ) ; +#49723 = MANIFOLD_SOLID_BREP ( 'ÊäÈë121', #50276 ) ; +#49724 = PRESENTATION_STYLE_ASSIGNMENT (( #3232 ) ) ; +#49725 = LINE ( 'NONE', #16494, #1088 ) ; +#49726 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17114, #65601, #50337 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49727 = LINE ( 'NONE', #58906, #48614 ) ; +#49728 = AXIS2_PLACEMENT_3D ( 'NONE', #79846, #94620, #26229 ) ; +#49729 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49731 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49730 = SURFACE_STYLE_USAGE ( .BOTH. , #41058 ) ; +#49732 = FILL_AREA_STYLE ('',( #88507 ) ) ; +#49733 = FILL_AREA_STYLE_COLOUR ( '', #80025 ) ; +#49734 = SURFACE_SIDE_STYLE ('',( #41553 ) ) ; +#49735 = VECTOR ( 'NONE', #19184, 1000.000000000000000 ) ; +#49736 = LINE ( 'NONE', #34413, #92458 ) ; +#49737 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89723 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36783, #67403, #13726 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49738 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#49739 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49741 = EDGE_CURVE ( 'NONE', #62005, #47130, #2536, .T. ) ; +#49740 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49742 = VECTOR ( 'NONE', #50885, 1000.000000000000000 ) ; +#49743 = CARTESIAN_POINT ( 'NONE', ( -1.015539310577060039, -0.9199924700473179895, 0.8100000000000000533 ) ) ; +#49744 = CARTESIAN_POINT ( 'NONE', ( 1.047921542718980081, -0.9264544496121609463, 0.8100000000000000533 ) ) ; +#49745 = VERTEX_POINT ( 'NONE', #4212 ) ; +#49747 = AXIS2_PLACEMENT_3D ( 'NONE', #16196, #9985, #79032 ) ; +#49746 = FACE_OUTER_BOUND ( 'NONE', #74480, .T. ) ; +#49748 = STYLED_ITEM ( 'NONE', ( #50108 ), #26976 ) ; +#49749 = ORIENTED_EDGE ( 'NONE', *, *, #65086, .T. ) ; +#49751 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49750 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49752 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220085265, 2.499999999999999556, 0.000000000000000000 ) ) ; +#49753 = CARTESIAN_POINT ( 'NONE', ( 1.580074546203000363, -1.378252124432310266, 0.8099999999999976108 ) ) ; +#49754 = DIRECTION ( 'NONE', ( -1.626303258728260102E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49755 = CARTESIAN_POINT ( 'NONE', ( 0.2638348760318000030, -1.377348110544800219, 0.8299999999999999600 ) ) ; +#49756 = LINE ( 'NONE', #2279, #71481 ) ; +#49757 = LINE ( 'NONE', #63568, #83545 ) ; +#49758 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#49759 = ORIENTED_EDGE ( 'NONE', *, *, #26572, .F. ) ; +#49760 = FILL_AREA_STYLE_COLOUR ( '', #65233 ) ; +#49761 = LINE ( 'NONE', #35455, #2177 ) ; +#49762 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49764 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30177 ) ) ; +#49763 = FILL_AREA_STYLE ('',( #4276 ) ) ; +#49765 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49766 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49767 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#49768 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#49769 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#49770 = FACE_OUTER_BOUND ( 'NONE', #74671, .T. ) ; +#49771 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#49772 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#49773 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722699999999918, 0.8991599999999999593 ) ) ; +#49774 = VECTOR ( 'NONE', #54889, 1000.000000000000000 ) ; +#49775 = FACE_OUTER_BOUND ( 'NONE', #47802, .T. ) ; +#49776 = LINE ( 'NONE', #55427, #81163 ) ; +#49777 = ORIENTED_EDGE ( 'NONE', *, *, #86894, .T. ) ; +#49778 = SURFACE_SIDE_STYLE ('',( #11365 ) ) ; +#49779 = VERTEX_POINT ( 'NONE', #1535 ) ; +#49780 = VECTOR ( 'NONE', #85452, 1000.000000000000000 ) ; +#49781 = ADVANCED_FACE ( 'NONE', ( #47986 ), #87285, .T. ) ; +#49782 = CYLINDRICAL_SURFACE ( 'NONE', #26914, 0.05000000000000012768 ) ; +#49783 = FACE_OUTER_BOUND ( 'NONE', #82093, .T. ) ; +#49784 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87278 ) ) ; +#49785 = FACE_OUTER_BOUND ( 'NONE', #12126, .T. ) ; +#49786 = CARTESIAN_POINT ( 'NONE', ( 1.856855962848350083, -0.9758031678253591412, 0.8299999999999999600 ) ) ; +#49787 = LINE ( 'NONE', #12379, #53238 ) ; +#49788 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49789 = ORIENTED_EDGE ( 'NONE', *, *, #58312, .T. ) ; +#49790 = FACE_OUTER_BOUND ( 'NONE', #86713, .T. ) ; +#49791 = EDGE_CURVE ( 'NONE', #13861, #53940, #57064, .T. ) ; +#49792 = VECTOR ( 'NONE', #39992, 1000.000000000000000 ) ; +#49793 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#49794 = ORIENTED_EDGE ( 'NONE', *, *, #41218, .T. ) ; +#49795 = CARTESIAN_POINT ( 'NONE', ( 8.199238745930522043, 10.59871325406948017, 0.8991599999999999593 ) ) ; +#49796 = VECTOR ( 'NONE', #75083, 1000.000000000000000 ) ; +#49797 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49798 = EDGE_CURVE ( 'NONE', #98326, #11668, #24544, .T. ) ; +#49799 = PLANE ( 'NONE', #98300 ) ; +#49800 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43203 ) ) ; +#49801 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49802 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49803 = STYLED_ITEM ( 'NONE', ( #56418 ), #71925 ) ; +#49804 = ORIENTED_EDGE ( 'NONE', *, *, #44700, .T. ) ; +#49805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49806 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49807 = VECTOR ( 'NONE', #9739, 1000.000000000000000 ) ; +#49808 = VECTOR ( 'NONE', #76449, 1000.000000000000000 ) ; +#49809 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49810 = VECTOR ( 'NONE', #91220, 1000.000000000000000 ) ; +#49811 = EDGE_LOOP ( 'NONE', ( #80170, #76026, #92061, #78021 ) ) ; +#49812 = AXIS2_PLACEMENT_3D ( 'NONE', #86530, #86013, #25284 ) ; +#49813 = CARTESIAN_POINT ( 'NONE', ( -0.3870363089776986953, 0.5647286298174479802, 0.8100000000000001643 ) ) ; +#49814 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49815 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 5.910594999999999821, 0.8648700000000000276 ) ) ; +#49816 = STYLED_ITEM ( 'NONE', ( #11790 ), #78312 ) ; +#49817 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#49818 = VECTOR ( 'NONE', #30698, 1000.000000000000000 ) ; +#49819 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#49820 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #84367 ) ; +#49821 = STYLED_ITEM ( 'NONE', ( #92455 ), #77214 ) ; +#49822 = ORIENTED_EDGE ( 'NONE', *, *, #4498, .F. ) ; +#49824 = EDGE_LOOP ( 'NONE', ( #81435, #11022, #2535, #31710 ) ) ; +#49823 = FACE_OUTER_BOUND ( 'NONE', #9064, .T. ) ; +#49826 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98605 ) ) ; +#49825 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15753, 'distance_accuracy_value', 'NONE'); +#49827 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49828 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#49830 = VECTOR ( 'NONE', #50798, 1000.000000000000000 ) ; +#49829 = PRESENTATION_STYLE_ASSIGNMENT (( #19140 ) ) ; +#49831 = ADVANCED_FACE ( 'NONE', ( #17323 ), #57189, .T. ) ; +#49832 = ORIENTED_EDGE ( 'NONE', *, *, #5162, .F. ) ; +#49833 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8100000000000000533 ) ) ; +#49834 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41664 ) ) ; +#49835 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#49836 = FILL_AREA_STYLE ('',( #57000 ) ) ; +#49837 = VERTEX_POINT ( 'NONE', #88307 ) ; +#49839 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#49838 = FACE_OUTER_BOUND ( 'NONE', #393, .T. ) ; +#49840 = ORIENTED_EDGE ( 'NONE', *, *, #39289, .F. ) ; +#49841 = EDGE_LOOP ( 'NONE', ( #71635, #37121, #77332, #69484, #59390, #34775 ) ) ; +#49842 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#49843 = AXIS2_PLACEMENT_3D ( 'NONE', #66799, #50521, #19844 ) ; +#49845 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#49844 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#49846 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#49847 = PLANE ( 'NONE', #65342 ) ; +#49848 = ORIENTED_EDGE ( 'NONE', *, *, #31508, .F. ) ; +#49849 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36782 ) ) ; +#49850 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#49851 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36785 ) ) ; +#49852 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#49853 = ORIENTED_EDGE ( 'NONE', *, *, #78353, .F. ) ; +#49854 = SURFACE_STYLE_USAGE ( .BOTH. , #24874 ) ; +#49855 = ORIENTED_EDGE ( 'NONE', *, *, #88145, .F. ) ; +#49856 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49857 = CARTESIAN_POINT ( 'NONE', ( -1.297607782917340025, -1.181386160465659918, 0.8100000000000000533 ) ) ; +#49858 = EDGE_CURVE ( 'NONE', #86742, #48342, #49510, .T. ) ; +#49859 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#49860 = PRESENTATION_STYLE_ASSIGNMENT (( #27371 ) ) ; +#49861 = FILL_AREA_STYLE ('',( #43170 ) ) ; +#49862 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#49863 = ORIENTED_EDGE ( 'NONE', *, *, #61939, .T. ) ; +#49864 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49866 = VECTOR ( 'NONE', #22437, 1000.000000000000000 ) ; +#49865 = LINE ( 'NONE', #48373, #782 ) ; +#49868 = SURFACE_SIDE_STYLE ('',( #94264 ) ) ; +#49867 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49869 = SURFACE_STYLE_FILL_AREA ( #65669 ) ; +#49870 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78026, 'distance_accuracy_value', 'NONE'); +#49871 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49872 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92238 ) ) ; +#49873 = AXIS2_PLACEMENT_3D ( 'NONE', #32695, #77632, #70458 ) ; +#49874 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74420 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8684, #15906, #47068 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49875 = FILL_AREA_STYLE_COLOUR ( '', #63167 ) ; +#49876 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49877 = FILL_AREA_STYLE_COLOUR ( '', #22238 ) ; +#49878 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49879 = EDGE_CURVE ( 'NONE', #2990, #60726, #14478, .T. ) ; +#49880 = ORIENTED_EDGE ( 'NONE', *, *, #16300, .T. ) ; +#49881 = VECTOR ( 'NONE', #84071, 1000.000000000000000 ) ; +#49883 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #79546 ) ; +#49882 = FILL_AREA_STYLE_COLOUR ( '', #89591 ) ; +#49884 = EDGE_CURVE ( 'NONE', #53914, #52681, #1617, .T. ) ; +#49885 = SURFACE_STYLE_USAGE ( .BOTH. , #18688 ) ; +#49886 = STYLED_ITEM ( 'NONE', ( #93002 ), #89150 ) ; +#49887 = FACE_OUTER_BOUND ( 'NONE', #80747, .T. ) ; +#49888 = DIRECTION ( 'NONE', ( 0.7071067811865460184, 0.7071067811865489050, 0.000000000000000000 ) ) ; +#49889 = SURFACE_STYLE_USAGE ( .BOTH. , #18691 ) ; +#49890 = STYLED_ITEM ( 'NONE', ( #50973 ), #78597 ) ; +#49892 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#49891 = SURFACE_STYLE_USAGE ( .BOTH. , #50411 ) ; +#49893 = FILL_AREA_STYLE_COLOUR ( '', #95661 ) ; +#49894 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#49895 = PLANE ( 'NONE', #51693 ) ; +#49896 = CARTESIAN_POINT ( 'NONE', ( 0.8333333333333293735, -3.500000000000000000, 0.000000000000000000 ) ) ; +#49897 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36821 ) ) ; +#49898 = SURFACE_STYLE_FILL_AREA ( #65185 ) ; +#49899 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#49900 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#49901 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#49903 = ADVANCED_FACE ( 'NONE', ( #78688 ), #8156, .T. ) ; +#49902 = FILL_AREA_STYLE_COLOUR ( '', #50566 ) ; +#49904 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93838 ), #18881 ) ; +#49905 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#49906 = VECTOR ( 'NONE', #24685, 1000.000000000000000 ) ; +#49907 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#49908 = ORIENTED_EDGE ( 'NONE', *, *, #99256, .T. ) ; +#49909 = LINE ( 'NONE', #9973, #14371 ) ; +#49910 = SURFACE_SIDE_STYLE ('',( #48891 ) ) ; +#49911 = VECTOR ( 'NONE', #36153, 1000.000000000000000 ) ; +#49912 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#49913 = LINE ( 'NONE', #53774, #44346 ) ; +#49914 = EDGE_CURVE ( 'NONE', #7208, #60362, #24623, .T. ) ; +#49915 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61360 ) ) ; +#49916 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49917 = ORIENTED_EDGE ( 'NONE', *, *, #39802, .F. ) ; +#49918 = LINE ( 'NONE', #66221, #89606 ) ; +#49919 = PRESENTATION_STYLE_ASSIGNMENT (( #64709 ) ) ; +#49920 = VECTOR ( 'NONE', #29940, 1000.000000000000000 ) ; +#49921 = SURFACE_SIDE_STYLE ('',( #3452 ) ) ; +#49922 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51670 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73409, #4919, #3463 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49923 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4850000000000000977, 0.2399999999999999911 ) ) ; +#49924 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#49925 = ORIENTED_EDGE ( 'NONE', *, *, #75276, .T. ) ; +#49926 = ORIENTED_EDGE ( 'NONE', *, *, #25996, .F. ) ; +#49927 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.100000000000000311, -0.02000000000000000042 ) ) ; +#49928 = LINE ( 'NONE', #25946, #24668 ) ; +#49929 = ORIENTED_EDGE ( 'NONE', *, *, #93495, .T. ) ; +#49930 = CARTESIAN_POINT ( 'NONE', ( 1.736362623504380087, -1.223383224893549892, 0.8100000000000000533 ) ) ; +#49931 = ADVANCED_FACE ( 'NONE', ( #33256 ), #79210, .T. ) ; +#49932 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25444 ) ) ; +#49933 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49934 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49935 = FILL_AREA_STYLE_COLOUR ( '', #56300 ) ; +#49936 = CARTESIAN_POINT ( 'NONE', ( -1.216120372379269954, -0.8900438058027670962, 0.8299999999999997380 ) ) ; +#49937 = EDGE_CURVE ( 'NONE', #10654, #37758, #55089, .T. ) ; +#49938 = CARTESIAN_POINT ( 'NONE', ( 0.9940821325528270691, -1.424266694256208332, 0.8099999999997231637 ) ) ; +#49939 = AXIS2_PLACEMENT_3D ( 'NONE', #23857, #94757, #46792 ) ; +#49941 = VERTEX_POINT ( 'NONE', #34288 ) ; +#49940 = ORIENTED_EDGE ( 'NONE', *, *, #47586, .T. ) ; +#49942 = EDGE_LOOP ( 'NONE', ( #25101, #4184, #61002, #42792 ) ) ; +#49943 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#49944 = STYLED_ITEM ( 'NONE', ( #11467 ), #83837 ) ; +#49945 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50431 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95259, #15640, #48370 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49946 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20014, 'distance_accuracy_value', 'NONE'); +#49947 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29451 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16788, #93382, #62815 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49948 = CARTESIAN_POINT ( 'NONE', ( 1.876343683457829981, -1.423344911062679907, 0.8299999999999999600 ) ) ; +#49950 = LINE ( 'NONE', #50957, #72477 ) ; +#49949 = CARTESIAN_POINT ( 'NONE', ( 0.5141275518124609478, -0.9686402964547039529, 0.8299999999999999600 ) ) ; +#49951 = ORIENTED_EDGE ( 'NONE', *, *, #56905, .T. ) ; +#49952 = ADVANCED_FACE ( 'NONE', ( #18915 ), #73564, .T. ) ; +#49953 = STYLED_ITEM ( 'NONE', ( #94075 ), #49668 ) ; +#49954 = VECTOR ( 'NONE', #73584, 1000.000000000000000 ) ; +#49955 = FILL_AREA_STYLE_COLOUR ( '', #64594 ) ; +#49956 = LINE ( 'NONE', #81097, #49007 ) ; +#49957 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#49958 = ORIENTED_EDGE ( 'NONE', *, *, #11432, .T. ) ; +#49959 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#49960 = ORIENTED_EDGE ( 'NONE', *, *, #9836, .T. ) ; +#49961 = AXIS2_PLACEMENT_3D ( 'NONE', #19890, #81701, #28075 ) ; +#49963 = FILL_AREA_STYLE_COLOUR ( '', #42007 ) ; +#49962 = PLANE ( 'NONE', #78034 ) ; +#49964 = ORIENTED_EDGE ( 'NONE', *, *, #20020, .T. ) ; +#49965 = EDGE_LOOP ( 'NONE', ( #6621, #90989, #78514, #53608 ) ) ; +#49966 = FACE_OUTER_BOUND ( 'NONE', #12932, .T. ) ; +#49967 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36896 ) ) ; +#49969 = SURFACE_STYLE_FILL_AREA ( #19284 ) ; +#49968 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#49970 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7500000000000002220, 0.000000000000000000 ) ) ; +#49971 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32603 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46422, #22458, #24521 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49973 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #43095, #18595, #34966, #90569 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#49972 = PRESENTATION_STYLE_ASSIGNMENT (( #58143 ) ) ; +#49974 = ORIENTED_EDGE ( 'NONE', *, *, #50911, .T. ) ; +#49975 = PLANE ( 'NONE', #54775 ) ; +#49976 = ORIENTED_EDGE ( 'NONE', *, *, #21909, .F. ) ; +#49977 = CARTESIAN_POINT ( 'NONE', ( -0.1903619263518360194, -0.9137302873894740385, 0.8299999999999999600 ) ) ; +#49978 = SURFACE_STYLE_FILL_AREA ( #42305 ) ; +#49979 = EDGE_LOOP ( 'NONE', ( #89582, #26063, #39341, #41671 ) ) ; +#49981 = PLANE ( 'NONE', #28959 ) ; +#49980 = SURFACE_STYLE_FILL_AREA ( #23981 ) ; +#49982 = ORIENTED_EDGE ( 'NONE', *, *, #1993, .F. ) ; +#49983 = ORIENTED_EDGE ( 'NONE', *, *, #38311, .T. ) ; +#49984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75531 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25091, #47522, #79704 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49985 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#49986 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49987 = LINE ( 'NONE', #34168, #51361 ) ; +#49988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83152 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92654, #12999, #36589 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#49989 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#49991 = ADVANCED_FACE ( 'NONE', ( #49593 ), #99801, .T. ) ; +#49990 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#49992 = VECTOR ( 'NONE', #51040, 1000.000000000000000 ) ; +#49993 = ADVANCED_FACE ( 'NONE', ( #65912 ), #89381, .T. ) ; +#49994 = PRESENTATION_STYLE_ASSIGNMENT (( #88766 ) ) ; +#49995 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#49996 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52625, 'distance_accuracy_value', 'NONE'); +#49997 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90702 ) ) ; +#49998 = ORIENTED_EDGE ( 'NONE', *, *, #22320, .T. ) ; +#49999 = PRESENTATION_STYLE_ASSIGNMENT (( #50505 ) ) ; +#50000 = ORIENTED_EDGE ( 'NONE', *, *, #93188, .F. ) ; +#50001 = VECTOR ( 'NONE', #13973, 1000.000000000000000 ) ; +#50002 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -0.1499999999999999944 ) ) ; +#50003 = CARTESIAN_POINT ( 'NONE', ( 1.367767600758680091, -1.205184960463220323, 0.8299999999999999600 ) ) ; +#50005 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79269 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61492, #38487, #53311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50004 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#50006 = SURFACE_SIDE_STYLE ('',( #48491 ) ) ; +#50007 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8199999999999999512 ) ) ; +#50008 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#50009 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.000000000000000000 ) ) ; +#50010 = PRESENTATION_STYLE_ASSIGNMENT (( #97406 ) ) ; +#50011 = EDGE_CURVE ( 'NONE', #81506, #69223, #6906, .T. ) ; +#50012 = VERTEX_POINT ( 'NONE', #69766 ) ; +#50013 = EDGE_CURVE ( 'NONE', #79565, #55846, #15628, .T. ) ; +#50014 = FACE_OUTER_BOUND ( 'NONE', #71658, .T. ) ; +#50015 = SURFACE_SIDE_STYLE ('',( #27525 ) ) ; +#50016 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#50017 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#50018 = ADVANCED_FACE ( 'NONE', ( #45755 ), #16034, .T. ) ; +#50019 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50020 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000000490, 0.8648700000000000276 ) ) ; +#50021 = PLANE ( 'NONE', #1639 ) ; +#50022 = VECTOR ( 'NONE', #30218, 1000.000000000000000 ) ; +#50023 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8648700000000000276 ) ) ; +#50024 = CARTESIAN_POINT ( 'NONE', ( -0.8073670843789639839, 0.5792268695032709580, 0.8299999999999999600 ) ) ; +#50025 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#50026 = EDGE_CURVE ( 'NONE', #92697, #16753, #100795, .T. ) ; +#50027 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72881 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63544, #79860, #56403 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50028 = EDGE_LOOP ( 'NONE', ( #95482, #422, #32230, #34674, #26105, #82111 ) ) ; +#50029 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50030 = FILL_AREA_STYLE ('',( #88801 ) ) ; +#50031 = VERTEX_POINT ( 'NONE', #8414 ) ; +#50032 = FACE_OUTER_BOUND ( 'NONE', #26805, .T. ) ; +#50033 = SURFACE_SIDE_STYLE ('',( #80664 ) ) ; +#50034 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#50035 = ADVANCED_FACE ( 'NONE', ( #46265 ), #30443, .T. ) ; +#50037 = VECTOR ( 'NONE', #85206, 1000.000000000000000 ) ; +#50036 = CARTESIAN_POINT ( 'NONE', ( 1.767907037466160070, -0.9096959278232360502, 0.8299999999999999600 ) ) ; +#50039 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#50038 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1090 ), #51644 ) ; +#50040 = CARTESIAN_POINT ( 'NONE', ( 1.798434352155980021, -1.039339352017210061, 0.8100000000000006084 ) ) ; +#50041 = ADVANCED_FACE ( 'NONE', ( #72815 ), #2371, .T. ) ; +#50042 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38215 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30036, #31063, #14692 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50043 = PLANE ( 'NONE', #97152 ) ; +#50044 = ORIENTED_EDGE ( 'NONE', *, *, #23818, .F. ) ; +#50045 = EDGE_CURVE ( 'NONE', #94573, #32396, #43744, .T. ) ; +#50046 = ORIENTED_EDGE ( 'NONE', *, *, #54343, .T. ) ; +#50047 = VECTOR ( 'NONE', #33550, 1000.000000000000000 ) ; +#50048 = FILL_AREA_STYLE_COLOUR ( '', #16101 ) ; +#50049 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90075, 'distance_accuracy_value', 'NONE'); +#50050 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#50051 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50052 = LINE ( 'NONE', #34225, #41768 ) ; +#50053 = SURFACE_STYLE_USAGE ( .BOTH. , #43350 ) ; +#50054 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50055 = CARTESIAN_POINT ( 'NONE', ( -0.5701283774939980287, -1.188292975353419934, 0.8100000000000000533 ) ) ; +#50056 = VECTOR ( 'NONE', #1293, 1000.000000000000000 ) ; +#50057 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50058 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50059 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50060 = MANIFOLD_SOLID_BREP ( 'ÊäÈë130', #64811 ) ; +#50062 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28803 ), #4384 ) ; +#50061 = FILL_AREA_STYLE_COLOUR ( '', #52638 ) ; +#50063 = VERTEX_POINT ( 'NONE', #48841 ) ; +#50064 = VECTOR ( 'NONE', #82919, 1000.000000000000000 ) ; +#50065 = SURFACE_STYLE_USAGE ( .BOTH. , #65335 ) ; +#50066 = ORIENTED_EDGE ( 'NONE', *, *, #50094, .T. ) ; +#50067 = FILL_AREA_STYLE_COLOUR ( '', #19637 ) ; +#50068 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36231 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44710, #90193, #91684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50069 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50070 = CARTESIAN_POINT ( 'NONE', ( -1.046906373037310045, -0.9912247593444889482, 0.8100000000000000533 ) ) ; +#50071 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50072 = ADVANCED_FACE ( 'NONE', ( #64155 ), #1867, .T. ) ; +#50073 = FACE_OUTER_BOUND ( 'NONE', #3375, .T. ) ; +#50075 = ORIENTED_EDGE ( 'NONE', *, *, #30604, .T. ) ; +#50074 = ORIENTED_EDGE ( 'NONE', *, *, #53810, .F. ) ; +#50076 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#50077 = ORIENTED_EDGE ( 'NONE', *, *, #21615, .F. ) ; +#50079 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50078 = PRESENTATION_STYLE_ASSIGNMENT (( #87842 ) ) ; +#50080 = ORIENTED_EDGE ( 'NONE', *, *, #87107, .F. ) ; +#50081 = EDGE_CURVE ( 'NONE', #12592, #94831, #27363, .T. ) ; +#50082 = ORIENTED_EDGE ( 'NONE', *, *, #10453, .T. ) ; +#50083 = CARTESIAN_POINT ( 'NONE', ( 8.227523499499826087, 9.806752500500174108, 0.8991599999999999593 ) ) ; +#50084 = FILL_AREA_STYLE_COLOUR ( '', #57972 ) ; +#50085 = SURFACE_SIDE_STYLE ('',( #11157 ) ) ; +#50086 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41348 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73515, #4054, #28543 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50087 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50088 = EDGE_LOOP ( 'NONE', ( #78451, #7681, #91454, #82481 ) ) ; +#50089 = EDGE_CURVE ( 'NONE', #28002, #67856, #50854, .T. ) ; +#50090 = EDGE_LOOP ( 'NONE', ( #30992, #34056, #45230, #97091 ) ) ; +#50091 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50092 = ORIENTED_EDGE ( 'NONE', *, *, #50614, .T. ) ; +#50093 = PRESENTATION_STYLE_ASSIGNMENT (( #64875 ) ) ; +#50094 = EDGE_CURVE ( 'NONE', #69410, #7753, #37029, .T. ) ; +#50096 = VERTEX_POINT ( 'NONE', #36538 ) ; +#50095 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#50097 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#50098 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81069 ), #5973 ) ; +#50099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71261 ) ) ; +#50100 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50101 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50102 = ORIENTED_EDGE ( 'NONE', *, *, #42689, .T. ) ; +#50103 = CARTESIAN_POINT ( 'NONE', ( -0.09657079632682520620, -1.219829592979950084, 0.8100000000000000533 ) ) ; +#50104 = VERTEX_POINT ( 'NONE', #75814 ) ; +#50105 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#50106 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74575 ) ) ; +#50107 = SURFACE_SIDE_STYLE ('',( #28112 ) ) ; +#50108 = PRESENTATION_STYLE_ASSIGNMENT (( #25604 ) ) ; +#50109 = PRESENTATION_STYLE_ASSIGNMENT (( #81749 ) ) ; +#50110 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74578 ), #43568 ) ; +#50111 = CARTESIAN_POINT ( 'NONE', ( -1.094250269889780025, -1.238505293396390039, 0.8300000000000000711 ) ) ; +#50113 = EDGE_CURVE ( 'NONE', #68649, #42002, #89643, .T. ) ; +#50112 = LINE ( 'NONE', #48073, #70508 ) ; +#50114 = EDGE_CURVE ( 'NONE', #21301, #25185, #98709, .T. ) ; +#50115 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50119 = LINE ( 'NONE', #42440, #978 ) ; +#50118 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50117 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50120 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999957, 0.8648700000000000276 ) ) ; +#50121 = ORIENTED_EDGE ( 'NONE', *, *, #75748, .F. ) ; +#50122 = CARTESIAN_POINT ( 'NONE', ( 1.652046208920949999, -1.504992180692799941, 0.8099999999999982769 ) ) ; +#50123 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89449 ) ) ; +#50124 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29565 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29383, #49627, #80773 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50125 = CARTESIAN_POINT ( 'NONE', ( -1.147844963924800066, -0.8845642871695170717, 0.8300000000000000711 ) ) ; +#50126 = ORIENTED_EDGE ( 'NONE', *, *, #83718, .T. ) ; +#50127 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#50128 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50129 = AXIS2_PLACEMENT_3D ( 'NONE', #29397, #60567, #92166 ) ; +#50130 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59965 ), #9260 ) ; +#50131 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50132 = FILL_AREA_STYLE_COLOUR ( '', #17685 ) ; +#50133 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50134 = CLOSED_SHELL ( 'NONE', ( #80667, #81880, #77621, #75612, #38948, #49781 ) ) ; +#50135 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50136 = EDGE_CURVE ( 'NONE', #90990, #605, #98221, .T. ) ; +#50137 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51790 ), #79488 ) ; +#50138 = ADVANCED_FACE ( 'NONE', ( #90127 ), #5326, .T. ) ; +#50139 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50140 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50141 = SURFACE_SIDE_STYLE ('',( #41956 ) ) ; +#50142 = VECTOR ( 'NONE', #16831, 1000.000000000000000 ) ; +#50143 = SURFACE_STYLE_USAGE ( .BOTH. , #34316 ) ; +#50144 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46799 ), #87641 ) ; +#50145 = EDGE_LOOP ( 'NONE', ( #98656, #31224, #79090, #53663 ) ) ; +#50147 = PRESENTATION_STYLE_ASSIGNMENT (( #80770 ) ) ; +#50146 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#50148 = PRESENTATION_STYLE_ASSIGNMENT (( #64929 ) ) ; +#50149 = EDGE_CURVE ( 'NONE', #72982, #13908, #97264, .T. ) ; +#50150 = ORIENTED_EDGE ( 'NONE', *, *, #67699, .T. ) ; +#50151 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#50152 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -5.551115123125790098E-17 ) ) ; +#50153 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#50154 = EDGE_CURVE ( 'NONE', #49021, #25087, #52846, .T. ) ; +#50155 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, -3.149999999999990585, 0.000000000000000000 ) ) ; +#50156 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#50157 = PRESENTATION_STYLE_ASSIGNMENT (( #26155 ) ) ; +#50158 = VECTOR ( 'NONE', #12975, 1000.000000000000000 ) ; +#50159 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50160 = PLANE ( 'NONE', #92858 ) ; +#50161 = CARTESIAN_POINT ( 'NONE', ( 0.6702516233766230291, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#50162 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57473, 'distance_accuracy_value', 'NONE'); +#50163 = EDGE_CURVE ( 'NONE', #48204, #17884, #66154, .T. ) ; +#50164 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.723820061220085131, 0.000000000000000000 ) ) ; +#50165 = ORIENTED_EDGE ( 'NONE', *, *, #73771, .F. ) ; +#50166 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#50167 = ADVANCED_FACE ( 'NONE', ( #86497 ), #84476, .T. ) ; +#50168 = ORIENTED_EDGE ( 'NONE', *, *, #44980, .T. ) ; +#50169 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50170 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46177, 'distance_accuracy_value', 'NONE'); +#50171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63637, 'distance_accuracy_value', 'NONE'); +#50172 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50173 = SURFACE_STYLE_FILL_AREA ( #18976 ) ; +#50174 = SURFACE_STYLE_USAGE ( .BOTH. , #89933 ) ; +#50175 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55040 ) ) ; +#50176 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50177 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333313320, -2.700000000000000178, 1.747825839084491125E-76 ) ) ; +#50178 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#50179 = LINE ( 'NONE', #75146, #3248 ) ; +#50180 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50181 = EDGE_LOOP ( 'NONE', ( #74108, #69309, #87739, #39641 ) ) ; +#50183 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89289 ), #100573 ) ; +#50184 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50185 = SURFACE_SIDE_STYLE ('',( #25188 ) ) ; +#50186 = ORIENTED_EDGE ( 'NONE', *, *, #40314, .T. ) ; +#50187 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50188 = ORIENTED_EDGE ( 'NONE', *, *, #26739, .F. ) ; +#50189 = SURFACE_STYLE_FILL_AREA ( #88963 ) ; +#50190 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#50191 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50192 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#50193 = EDGE_CURVE ( 'NONE', #28522, #56990, #14487, .T. ) ; +#50195 = PRESENTATION_STYLE_ASSIGNMENT (( #65986 ) ) ; +#50194 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12974 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100093, #67539, #45532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50196 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8199999999999999512 ) ) ; +#50197 = ORIENTED_EDGE ( 'NONE', *, *, #71517, .F. ) ; +#50198 = CYLINDRICAL_SURFACE ( 'NONE', #73984, 0.02999999999999997113 ) ; +#50199 = ORIENTED_EDGE ( 'NONE', *, *, #46925, .T. ) ; +#50200 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50201 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50202 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35539 ), #4518 ) ; +#50203 = SHAPE_REPRESENTATION ( 'Submodel-IPEX_4P_part_IPEX_4P', ( #69623, #82704 ), #71397 ) ; +#50204 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50205 = CLOSED_SHELL ( 'NONE', ( #95044, #58758, #95551, #52827, #64894, #93816 ) ) ; +#50206 = ORIENTED_EDGE ( 'NONE', *, *, #96627, .F. ) ; +#50207 = ADVANCED_FACE ( 'NONE', ( #38522 ), #31862, .T. ) ; +#50208 = ORIENTED_EDGE ( 'NONE', *, *, #33390, .F. ) ; +#50209 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94146 ) ) ; +#50210 = SURFACE_STYLE_FILL_AREA ( #41514 ) ; +#50211 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#50212 = LINE ( 'NONE', #50703, #9455 ) ; +#50213 = SURFACE_SIDE_STYLE ('',( #2212 ) ) ; +#50215 = CARTESIAN_POINT ( 'NONE', ( 5.264745124874999682, 5.557041124875000904, 0.8648700000000000276 ) ) ; +#50214 = CARTESIAN_POINT ( 'NONE', ( 0.3269029137381110339, -0.9653181426176251634, 0.8100000000000000533 ) ) ; +#50216 = EDGE_LOOP ( 'NONE', ( #65159, #14075, #81346, #93445, #93612, #2481 ) ) ; +#50218 = ADVANCED_FACE ( 'NONE', ( #100670 ), #85987, .T. ) ; +#50217 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #50558, #82894 ), #43760 ) ; +#50220 = ORIENTED_EDGE ( 'NONE', *, *, #23646, .F. ) ; +#50219 = ORIENTED_EDGE ( 'NONE', *, *, #100916, .T. ) ; +#50221 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50222 = ORIENTED_EDGE ( 'NONE', *, *, #28120, .F. ) ; +#50223 = STYLED_ITEM ( 'NONE', ( #88261 ), #14844 ) ; +#50224 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.5000000000000018874, 0.1829999999999659677 ) ) ; +#50225 = EDGE_CURVE ( 'NONE', #23798, #95862, #39835, .T. ) ; +#50226 = ORIENTED_EDGE ( 'NONE', *, *, #23002, .F. ) ; +#50228 = ORIENTED_EDGE ( 'NONE', *, *, #69382, .T. ) ; +#50227 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 1.100000000000000089, 0.000000000000000000 ) ) ; +#50229 = ORIENTED_EDGE ( 'NONE', *, *, #96924, .T. ) ; +#50230 = FILL_AREA_STYLE_COLOUR ( '', #34194 ) ; +#50231 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33129, #62779, #70924, #41313 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 3.386137796821731712E-15, 0.0001118058566273296491 ), + .UNSPECIFIED. ) ; +#50232 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50233 = PRESENTATION_STYLE_ASSIGNMENT (( #58393 ) ) ; +#50234 = EDGE_LOOP ( 'NONE', ( #17110, #98527, #10256, #59155 ) ) ; +#50235 = MANIFOLD_SOLID_BREP ( 'ÊäÈë16', #56831 ) ; +#50236 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01500000000000000118, 0.2399999999999999911 ) ) ; +#50237 = PRESENTATION_STYLE_ASSIGNMENT (( #28229 ) ) ; +#50238 = CARTESIAN_POINT ( 'NONE', ( 0.4283467773376269938, -1.261010674219189998, 0.8299999999999999600 ) ) ; +#50239 = AXIS2_PLACEMENT_3D ( 'NONE', #38359, #62865, #54698 ) ; +#50241 = EDGE_CURVE ( 'NONE', #6655, #2974, #17526, .T. ) ; +#50240 = PRESENTATION_STYLE_ASSIGNMENT (( #65022 ) ) ; +#50242 = ADVANCED_FACE ( 'NONE', ( #41063 ), #26747, .T. ) ; +#50243 = PLANE ( 'NONE', #38929 ) ; +#50244 = FILL_AREA_STYLE_COLOUR ( '', #83863 ) ; +#50245 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#50246 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50247 = EDGE_CURVE ( 'NONE', #96985, #65920, #50895, .T. ) ; +#50248 = VECTOR ( 'NONE', #56432, 1000.000000000000000 ) ; +#50249 = FILL_AREA_STYLE_COLOUR ( '', #52016 ) ; +#50251 = FILL_AREA_STYLE ('',( #10302 ) ) ; +#50250 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#50252 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50253 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.383333333333330195, 1.747825839084982648E-76 ) ) ; +#50254 = EDGE_CURVE ( 'NONE', #97953, #24220, #76345, .T. ) ; +#50255 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#50256 = VECTOR ( 'NONE', #13854, 1000.000000000000000 ) ; +#50257 = CARTESIAN_POINT ( 'NONE', ( 1.190985675097830265, -0.8845231535185279492, 0.8100000000000000533 ) ) ; +#50258 = ORIENTED_EDGE ( 'NONE', *, *, #60730, .T. ) ; +#50259 = CARTESIAN_POINT ( 'NONE', ( -1.337569335501239909, -1.448219210431749948, 0.8300000000000024025 ) ) ; +#50260 = ADVANCED_FACE ( 'NONE', ( #4734 ), #13322, .T. ) ; +#50261 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50262 = SURFACE_SIDE_STYLE ('',( #20065 ) ) ; +#50263 = SURFACE_STYLE_FILL_AREA ( #19059 ) ; +#50264 = VECTOR ( 'NONE', #36023, 1000.000000000000000 ) ; +#50265 = ORIENTED_EDGE ( 'NONE', *, *, #94900, .F. ) ; +#50266 = SURFACE_STYLE_USAGE ( .BOTH. , #96656 ) ; +#50267 = LINE ( 'NONE', #26262, #22610 ) ; +#50268 = AXIS2_PLACEMENT_3D ( 'NONE', #54535, #45303, #54010 ) ; +#50270 = PRESENTATION_STYLE_ASSIGNMENT (( #89038 ) ) ; +#50269 = PRESENTATION_STYLE_ASSIGNMENT (( #98600 ) ) ; +#50271 = CARTESIAN_POINT ( 'NONE', ( 1.585431502668920078, -1.054251812769849916, 0.8100000000000000533 ) ) ; +#50272 = CARTESIAN_POINT ( 'NONE', ( -0.03881103786207359962, 1.364228230794140018, 0.8299999999999999600 ) ) ; +#50273 = CARTESIAN_POINT ( 'NONE', ( 0.2473788005703330406, -1.399092671493430196, 0.8100000000000000533 ) ) ; +#50274 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50275 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50276 = CLOSED_SHELL ( 'NONE', ( #67137, #93271, #18498, #39857, #29071, #35277 ) ) ; +#50277 = ORIENTED_EDGE ( 'NONE', *, *, #58088, .T. ) ; +#50278 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#50279 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94226 ) ) ; +#50280 = LINE ( 'NONE', #74229, #57182 ) ; +#50281 = LINE ( 'NONE', #34445, #28571 ) ; +#50282 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50283 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#50284 = CARTESIAN_POINT ( 'NONE', ( 11.49435687512499094, 6.539919875124987847, 0.8648700000000000276 ) ) ; +#50285 = FACE_OUTER_BOUND ( 'NONE', #88264, .T. ) ; +#50286 = FACE_OUTER_BOUND ( 'NONE', #50296, .T. ) ; +#50287 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#50288 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#50289 = FACE_OUTER_BOUND ( 'NONE', #70261, .T. ) ; +#50290 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97795, 'distance_accuracy_value', 'NONE'); +#50291 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58458 ) ) ; +#50292 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#50293 = CARTESIAN_POINT ( 'NONE', ( -2.799999999999999822, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#50294 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34959 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24877, #35541, #97745 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50295 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#50296 = EDGE_LOOP ( 'NONE', ( #11961, #44373, #5323, #2044 ) ) ; +#50297 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50298 = EDGE_CURVE ( 'NONE', #64204, #20901, #43044, .T. ) ; +#50299 = ORIENTED_EDGE ( 'NONE', *, *, #26402, .T. ) ; +#50300 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11533, 'distance_accuracy_value', 'NONE'); +#50301 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23766, 'distance_accuracy_value', 'NONE'); +#50302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13251 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94023, #40479, #71613 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50303 = MANIFOLD_SOLID_BREP ( 'ÊäÈë19', #30507 ) ; +#50304 = SURFACE_SIDE_STYLE ('',( #57961 ) ) ; +#50305 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#50306 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#50308 = ADVANCED_FACE ( 'NONE', ( #54233 ), #15390, .F. ) ; +#50307 = PLANE ( 'NONE', #87941 ) ; +#50309 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#50311 = ORIENTED_EDGE ( 'NONE', *, *, #65873, .F. ) ; +#50310 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68157 ) ) ; +#50312 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50313 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95372, 'distance_accuracy_value', 'NONE'); +#50314 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50315 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4022 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31007, #15657, #39167 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50316 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#50317 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55400 ), #6172 ) ; +#50318 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12663 ) ) ; +#50319 = VERTEX_POINT ( 'NONE', #38911 ) ; +#50320 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#50321 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000013517, 0.1829999999999710192 ) ) ; +#50322 = PLANE ( 'NONE', #13533 ) ; +#50323 = FACE_OUTER_BOUND ( 'NONE', #56973, .T. ) ; +#50324 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50325 = EDGE_CURVE ( 'NONE', #65258, #88593, #76194, .T. ) ; +#50326 = EDGE_LOOP ( 'NONE', ( #40410, #22777, #57081, #40521 ) ) ; +#50327 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, -0.02000000000002515044 ) ) ; +#50328 = SURFACE_STYLE_FILL_AREA ( #4319 ) ; +#50329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90299, 'distance_accuracy_value', 'NONE'); +#50330 = STYLED_ITEM ( 'NONE', ( #75870 ), #84506 ) ; +#50332 = SURFACE_STYLE_FILL_AREA ( #58495 ) ; +#50331 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50333 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50334 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8991599999999999593 ) ) ; +#50335 = VECTOR ( 'NONE', #3914, 1000.000000000000000 ) ; +#50336 = ORIENTED_EDGE ( 'NONE', *, *, #59502, .T. ) ; +#50337 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50338 = SURFACE_SIDE_STYLE ('',( #2827 ) ) ; +#50339 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50340 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50341 = ORIENTED_EDGE ( 'NONE', *, *, #7981, .F. ) ; +#50342 = CYLINDRICAL_SURFACE ( 'NONE', #79157, 0.05000000000000012768 ) ; +#50343 = STYLED_ITEM ( 'NONE', ( #20422 ), #17553 ) ; +#50344 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16009 ) ) ; +#50345 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95897 ), #100661 ) ; +#50346 = STYLED_ITEM ( 'NONE', ( #75449 ), #812 ) ; +#50347 = ADVANCED_FACE ( 'NONE', ( #8173 ), #93982, .F. ) ; +#50348 = ORIENTED_EDGE ( 'NONE', *, *, #91678, .F. ) ; +#50349 = ORIENTED_EDGE ( 'NONE', *, *, #3696, .F. ) ; +#50351 = PRESENTATION_STYLE_ASSIGNMENT (( #9896 ) ) ; +#50350 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50352 = LINE ( 'NONE', #3346, #7148 ) ; +#50353 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01085786437626904723, 0.1499999999999999944 ) ) ; +#50354 = EDGE_CURVE ( 'NONE', #65057, #12156, #51795, .T. ) ; +#50355 = SURFACE_SIDE_STYLE ('',( #42165 ) ) ; +#50356 = ORIENTED_EDGE ( 'NONE', *, *, #85210, .F. ) ; +#50357 = FACE_OUTER_BOUND ( 'NONE', #96869, .T. ) ; +#50358 = LINE ( 'NONE', #97248, #38480 ) ; +#50359 = EDGE_LOOP ( 'NONE', ( #24457, #78955, #72016, #77248 ) ) ; +#50360 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42171 ), #97578 ) ; +#50361 = CARTESIAN_POINT ( 'NONE', ( -2.123820061220085265, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#50362 = VERTEX_POINT ( 'NONE', #31242 ) ; +#50363 = CARTESIAN_POINT ( 'NONE', ( 1.008379832179014501, -1.144781931243858075, 0.8099999999998986899 ) ) ; +#50364 = EDGE_CURVE ( 'NONE', #70019, #49397, #23591, .T. ) ; +#50365 = STYLED_ITEM ( 'NONE', ( #66688 ), #15168 ) ; +#50367 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.069338999999999817, 0.8648700000000000276 ) ) ; +#50366 = SURFACE_SIDE_STYLE ('',( #51344 ) ) ; +#50368 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53272 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61022, #7294, #77820 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50369 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50370 = ORIENTED_EDGE ( 'NONE', *, *, #12768, .T. ) ; +#50372 = ADVANCED_FACE ( 'NONE', ( #57278 ), #54660, .T. ) ; +#50371 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68223 ), #20955 ) ; +#50373 = ADVANCED_FACE ( 'NONE', ( #34306 ), #22726, .T. ) ; +#50374 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50375 = ORIENTED_EDGE ( 'NONE', *, *, #42784, .F. ) ; +#50376 = FILL_AREA_STYLE_COLOUR ( '', #2629 ) ; +#50377 = SURFACE_STYLE_FILL_AREA ( #53227 ) ; +#50378 = ORIENTED_EDGE ( 'NONE', *, *, #55836, .T. ) ; +#50379 = SURFACE_STYLE_FILL_AREA ( #19174 ) ; +#50380 = CARTESIAN_POINT ( 'NONE', ( -1.371024924951979918, -1.079235908285120171, 0.8299999999999999600 ) ) ; +#50381 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#50382 = EDGE_CURVE ( 'NONE', #50950, #83700, #58299, .T. ) ; +#50383 = FACE_OUTER_BOUND ( 'NONE', #64603, .T. ) ; +#50384 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#50385 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50386 = LINE ( 'NONE', #4368, #47011 ) ; +#50387 = EDGE_CURVE ( 'NONE', #26954, #13552, #5096, .T. ) ; +#50388 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89194 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46852, #47885, #47378 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50389 = AXIS2_PLACEMENT_3D ( 'NONE', #17696, #363, #16174 ) ; +#50390 = ORIENTED_EDGE ( 'NONE', *, *, #70850, .F. ) ; +#50391 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#50392 = CARTESIAN_POINT ( 'NONE', ( -0.2761799387799139804, 3.099999999999980105, 0.000000000000000000 ) ) ; +#50393 = FILL_AREA_STYLE ('',( #95263 ) ) ; +#50394 = VECTOR ( 'NONE', #90864, 1000.000000000000114 ) ; +#50395 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50396 = STYLED_ITEM ( 'NONE', ( #23649 ), #84831 ) ; +#50397 = VECTOR ( 'NONE', #501, 1000.000000000000000 ) ; +#50398 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50399 = PRESENTATION_STYLE_ASSIGNMENT (( #20198 ) ) ; +#50400 = SURFACE_SIDE_STYLE ('',( #88651 ) ) ; +#50402 = ORIENTED_EDGE ( 'NONE', *, *, #79287, .F. ) ; +#50401 = STYLED_ITEM ( 'NONE', ( #94177 ), #55780 ) ; +#50404 = MANIFOLD_SOLID_BREP ( 'ÊäÈë68', #12627 ) ; +#50403 = SURFACE_SIDE_STYLE ('',( #12469 ) ) ; +#50405 = VECTOR ( 'NONE', #93796, 1000.000000000000000 ) ; +#50406 = PLANE ( 'NONE', #26193 ) ; +#50407 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50408 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#50409 = FACE_OUTER_BOUND ( 'NONE', #85445, .T. ) ; +#50410 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57852, 'distance_accuracy_value', 'NONE'); +#50411 = SURFACE_SIDE_STYLE ('',( #56553 ) ) ; +#50412 = FACE_OUTER_BOUND ( 'NONE', #47019, .T. ) ; +#50413 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50414 = SURFACE_SIDE_STYLE ('',( #2912 ) ) ; +#50415 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97622 ) ) ; +#50416 = SURFACE_SIDE_STYLE ('',( #43695 ) ) ; +#50417 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8648700000000000276 ) ) ; +#50418 = LINE ( 'NONE', #27922, #68323 ) ; +#50419 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50420 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81386 ) ) ; +#50421 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#50422 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27683 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92068, #84416, #15450 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50423 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50424 = SURFACE_STYLE_FILL_AREA ( #34584 ) ; +#50425 = CARTESIAN_POINT ( 'NONE', ( 1.780058980618379971, -1.124571705400470023, 0.8299999999999997380 ) ) ; +#50426 = SURFACE_SIDE_STYLE ('',( #82542 ) ) ; +#50427 = STYLED_ITEM ( 'NONE', ( #33771 ), #268 ) ; +#50428 = FILL_AREA_STYLE_COLOUR ( '', #36209 ) ; +#50429 = ORIENTED_EDGE ( 'NONE', *, *, #55935, .F. ) ; +#50430 = PLANE ( 'NONE', #91022 ) ; +#50431 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95259, 'distance_accuracy_value', 'NONE'); +#50432 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80635, 'distance_accuracy_value', 'NONE'); +#50433 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#50434 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50435 = CARTESIAN_POINT ( 'NONE', ( 0.3885234902190933259, -0.9631295002298508878, 0.8100000000000000533 ) ) ; +#50436 = ORIENTED_EDGE ( 'NONE', *, *, #86689, .T. ) ; +#50437 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#50438 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50439 = AXIS2_PLACEMENT_3D ( 'NONE', #40863, #74001, #71994 ) ; +#50440 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50441 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80914, 'distance_accuracy_value', 'NONE'); +#50442 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83969, 'distance_accuracy_value', 'NONE'); +#50443 = FACE_OUTER_BOUND ( 'NONE', #4773, .T. ) ; +#50444 = ADVANCED_FACE ( 'NONE', ( #51120 ), #18935, .T. ) ; +#50445 = ORIENTED_EDGE ( 'NONE', *, *, #20216, .T. ) ; +#50446 = ORIENTED_EDGE ( 'NONE', *, *, #67699, .F. ) ; +#50447 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#50448 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#50449 = EDGE_LOOP ( 'NONE', ( #7261, #75131, #29080, #24071 ) ) ; +#50450 = CARTESIAN_POINT ( 'NONE', ( 1.795983389471520031, -1.255590633215009966, 0.8299999999999999600 ) ) ; +#50451 = VECTOR ( 'NONE', #87110, 1000.000000000000000 ) ; +#50452 = FACE_OUTER_BOUND ( 'NONE', #92093, .T. ) ; +#50453 = FILL_AREA_STYLE_COLOUR ( '', #61111 ) ; +#50454 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48830 ), #39040 ) ; +#50455 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70440 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12992, #75357, #59589 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50456 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #48616, #58257 ) ; +#50457 = FILL_AREA_STYLE ('',( #3944 ) ) ; +#50458 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50460 = ORIENTED_EDGE ( 'NONE', *, *, #23142, .T. ) ; +#50459 = VERTEX_POINT ( 'NONE', #36786 ) ; +#50461 = ORIENTED_EDGE ( 'NONE', *, *, #26369, .F. ) ; +#50462 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #806 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36515, #83463, #73794 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50463 = EDGE_LOOP ( 'NONE', ( #5719, #75389, #29688, #95851 ) ) ; +#50464 = MANIFOLD_SOLID_BREP ( 'ÊäÈë168', #36984 ) ; +#50465 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#50466 = AXIS2_PLACEMENT_3D ( 'NONE', #59472, #58966, #12879 ) ; +#50467 = CARTESIAN_POINT ( 'NONE', ( 1.810234811980210079, -1.482878949593630091, 0.8100000000000000533 ) ) ; +#50468 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#50469 = ORIENTED_EDGE ( 'NONE', *, *, #83143, .T. ) ; +#50470 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3136 ), #37407 ) ; +#50471 = SURFACE_SIDE_STYLE ('',( #28949 ) ) ; +#50472 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91173 ), #16142 ) ; +#50473 = FILL_AREA_STYLE ('',( #19275 ) ) ; +#50474 = ORIENTED_EDGE ( 'NONE', *, *, #59706, .F. ) ; +#50476 = FILL_AREA_STYLE_COLOUR ( '', #38623 ) ; +#50475 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50477 = VERTEX_POINT ( 'NONE', #60787 ) ; +#50478 = ORIENTED_EDGE ( 'NONE', *, *, #7167, .T. ) ; +#50479 = SURFACE_SIDE_STYLE ('',( #58641 ) ) ; +#50480 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50481 = VECTOR ( 'NONE', #71609, 1000.000000000000000 ) ; +#50482 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50483 = ORIENTED_EDGE ( 'NONE', *, *, #4313, .T. ) ; +#50484 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#50485 = ADVANCED_FACE ( 'NONE', ( #11694 ), #68893, .T. ) ; +#50486 = EDGE_LOOP ( 'NONE', ( #59614, #93016, #24460, #87356, #17428, #100863 ) ) ; +#50487 = CARTESIAN_POINT ( 'NONE', ( -0.2919245839448350033, -1.051115598670280038, 0.8100000000000000533 ) ) ; +#50488 = ORIENTED_EDGE ( 'NONE', *, *, #38998, .F. ) ; +#50489 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50490 = PRESENTATION_STYLE_ASSIGNMENT (( #75938 ) ) ; +#50491 = ORIENTED_EDGE ( 'NONE', *, *, #73200, .F. ) ; +#50492 = ORIENTED_EDGE ( 'NONE', *, *, #4936, .T. ) ; +#50494 = FACE_OUTER_BOUND ( 'NONE', #83469, .T. ) ; +#50493 = CARTESIAN_POINT ( 'NONE', ( 0.3671721421540899977, -0.9001501144350020356, 0.8299999999999992939 ) ) ; +#50495 = SURFACE_SIDE_STYLE ('',( #20303 ) ) ; +#50496 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#50497 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50498 = FILL_AREA_STYLE_COLOUR ( '', #63835 ) ; +#50499 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#50501 = SURFACE_SIDE_STYLE ('',( #89274 ) ) ; +#50500 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91333 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8223, #92534, #39442 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50502 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50503 = EDGE_CURVE ( 'NONE', #34589, #95207, #99049, .T. ) ; +#50504 = ORIENTED_EDGE ( 'NONE', *, *, #54173, .T. ) ; +#50505 = SURFACE_STYLE_USAGE ( .BOTH. , #79621 ) ; +#50506 = EDGE_LOOP ( 'NONE', ( #76153, #25310, #49455, #27128 ) ) ; +#50507 = SURFACE_STYLE_USAGE ( .BOTH. , #19315 ) ; +#50508 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#50509 = CARTESIAN_POINT ( 'NONE', ( 1.186840394175660007, -1.149778012002649952, 0.8299999999999999600 ) ) ; +#50510 = PLANE ( 'NONE', #33350 ) ; +#50511 = SURFACE_SIDE_STYLE ('',( #89772 ) ) ; +#50512 = LINE ( 'NONE', #13093, #12470 ) ; +#50513 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#50514 = SURFACE_STYLE_FILL_AREA ( #42329 ) ; +#50515 = ORIENTED_EDGE ( 'NONE', *, *, #95963, .F. ) ; +#50516 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50517 = FILL_AREA_STYLE ('',( #82150 ) ) ; +#50518 = CARTESIAN_POINT ( 'NONE', ( 0.3170313104546300109, -0.9034630071664919715, 0.8299999999999999600 ) ) ; +#50519 = PLANE ( 'NONE', #8439 ) ; +#50520 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#50521 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50523 = CIRCLE ( 'NONE', #43992, 0.6999999999999999556 ) ; +#50524 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68390 ), #83145 ) ; +#50525 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50526 = LINE ( 'NONE', #41837, #15875 ) ; +#50527 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50528 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#50529 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50530 = SURFACE_SIDE_STYLE ('',( #33167 ) ) ; +#50531 = AXIS2_PLACEMENT_3D ( 'NONE', #68983, #83849, #37398 ) ; +#50532 = AXIS2_PLACEMENT_3D ( 'NONE', #2179, #25659, #86427 ) ; +#50533 = FILL_AREA_STYLE ('',( #74992 ) ) ; +#50534 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85789, 'distance_accuracy_value', 'NONE'); +#50535 = VECTOR ( 'NONE', #86025, 1000.000000000000000 ) ; +#50536 = ORIENTED_EDGE ( 'NONE', *, *, #91135, .T. ) ; +#50537 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50539 = ADVANCED_FACE ( 'NONE', ( #84248 ), #69907, .T. ) ; +#50538 = CARTESIAN_POINT ( 'NONE', ( 1.519746594691179897, -1.031932509624860161, 0.8100000000000000533 ) ) ; +#50540 = ORIENTED_EDGE ( 'NONE', *, *, #100444, .T. ) ; +#50541 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50542 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #357 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43125, #28806, #91589 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50543 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50544 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50545 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50546 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50547 = EDGE_LOOP ( 'NONE', ( #69430, #96978, #40928, #14634 ) ) ; +#50548 = ORIENTED_EDGE ( 'NONE', *, *, #58837, .F. ) ; +#50549 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71726 ) ) ; +#50550 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#50552 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8091 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100696, #5353, #37062 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50551 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#50553 = CARTESIAN_POINT ( 'NONE', ( -0.4616949353561959901, -1.145331018069290163, 0.8100000000000000533 ) ) ; +#50554 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71212, 'distance_accuracy_value', 'NONE'); +#50555 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#50556 = SURFACE_STYLE_FILL_AREA ( #67821 ) ; +#50557 = FILL_AREA_STYLE_COLOUR ( '', #1244 ) ; +#50558 = MANIFOLD_SOLID_BREP ( 'NONE', #86078 ) ; +#50559 = ADVANCED_FACE ( 'NONE', ( #48489 ), #2005, .T. ) ; +#50560 = ORIENTED_EDGE ( 'NONE', *, *, #61178, .F. ) ; +#50561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92881 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55220, #24597, #16855 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50562 = CARTESIAN_POINT ( 'NONE', ( -0.7453505133853431941, 1.552609075926967286, 0.8100000000000001643 ) ) ; +#50563 = ORIENTED_EDGE ( 'NONE', *, *, #6073, .T. ) ; +#50564 = ADVANCED_FACE ( 'NONE', ( #32655 ), #48986, .T. ) ; +#50565 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50566 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50567 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50568 = CARTESIAN_POINT ( 'NONE', ( -1.129230981225310071, -0.9561532343638800002, 0.8299999999999999600 ) ) ; +#50569 = CARTESIAN_POINT ( 'NONE', ( -0.4700584699050159854, -0.9114593501573470258, 0.8100000000000000533 ) ) ; +#50570 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#50572 = EDGE_LOOP ( 'NONE', ( #55624, #43653, #79591, #56341, #51600, #3950 ) ) ; +#50571 = ORIENTED_EDGE ( 'NONE', *, *, #9556, .F. ) ; +#50573 = AXIS2_PLACEMENT_3D ( 'NONE', #83437, #91575, #90586 ) ; +#50574 = EDGE_LOOP ( 'NONE', ( #97495, #27204, #10776, #1076 ) ) ; +#50575 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666632857, -2.100000000000000089, 0.000000000000000000 ) ) ; +#50577 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50576 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#50578 = EDGE_LOOP ( 'NONE', ( #59566, #93177, #13697, #78450 ) ) ; +#50579 = ADVANCED_FACE ( 'NONE', ( #25506 ), #87770, .T. ) ; +#50580 = ORIENTED_EDGE ( 'NONE', *, *, #49414, .T. ) ; +#50581 = SURFACE_SIDE_STYLE ('',( #5056 ) ) ; +#50582 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50583 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50585 = PRESENTATION_STYLE_ASSIGNMENT (( #34764 ) ) ; +#50584 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#50586 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#50587 = ORIENTED_EDGE ( 'NONE', *, *, #49441, .T. ) ; +#50588 = ORIENTED_EDGE ( 'NONE', *, *, #3443, .T. ) ; +#50589 = FILL_AREA_STYLE_COLOUR ( '', #40520 ) ; +#50590 = VERTEX_POINT ( 'NONE', #81645 ) ; +#50591 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50592 = CYLINDRICAL_SURFACE ( 'NONE', #42732, 0.2000000000000005107 ) ; +#50593 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42469 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84260, #77090, #38798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50594 = VECTOR ( 'NONE', #15226, 1000.000000000000000 ) ; +#50596 = VERTEX_POINT ( 'NONE', #82143 ) ; +#50595 = PLANE ( 'NONE', #78747 ) ; +#50597 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91299 ) ) ; +#50598 = ADVANCED_FACE ( 'NONE', ( #66783 ), #52003, .T. ) ; +#50599 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96544 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30208, #70535, #62402 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50600 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50601 = ORIENTED_EDGE ( 'NONE', *, *, #73101, .T. ) ; +#50602 = SURFACE_STYLE_USAGE ( .BOTH. , #13195 ) ; +#50603 = VERTEX_POINT ( 'NONE', #59687 ) ; +#50604 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92103, #61507, #75791, #76792 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#50605 = VERTEX_POINT ( 'NONE', #18809 ) ; +#50606 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#50608 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50607 = VECTOR ( 'NONE', #50527, 1000.000000000000000 ) ; +#50609 = CARTESIAN_POINT ( 'NONE', ( -1.371290353842550047, -1.066576130479129914, 0.8300000000000000711 ) ) ; +#50610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21193 ), #8288 ) ; +#50611 = SURFACE_STYLE_USAGE ( .BOTH. , #58780 ) ; +#50612 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#50613 = SURFACE_SIDE_STYLE ('',( #27124 ) ) ; +#50614 = EDGE_CURVE ( 'NONE', #49021, #51509, #82530, .T. ) ; +#50616 = SURFACE_STYLE_FILL_AREA ( #4603 ) ; +#50615 = SURFACE_STYLE_FILL_AREA ( #82245 ) ; +#50617 = CARTESIAN_POINT ( 'NONE', ( 1.549517223800989996, -0.9663557550577259736, 0.8299999999999997380 ) ) ; +#50618 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52212 ), #14671 ) ; +#50619 = ORIENTED_EDGE ( 'NONE', *, *, #94409, .F. ) ; +#50620 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69848 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62565, #78369, #24267 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50621 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.699999999999999734, 3.364833505069654667E-79 ) ) ; +#50622 = ORIENTED_EDGE ( 'NONE', *, *, #17809, .T. ) ; +#50623 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 1.600000000000000089, 0.000000000000000000 ) ) ; +#50624 = MANIFOLD_SOLID_BREP ( 'ÊäÈë149', #72843 ) ; +#50625 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#50626 = LINE ( 'NONE', #26130, #30022 ) ; +#50627 = SURFACE_SIDE_STYLE ('',( #90908 ) ) ; +#50629 = LINE ( 'NONE', #59308, #13223 ) ; +#50628 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2808578643762690286, 0.1399999999999980149 ) ) ; +#50630 = CARTESIAN_POINT ( 'NONE', ( 1.785976973916959976, -1.116141175150469955, 0.8299999999999999600 ) ) ; +#50631 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16302 ) ) ; +#50632 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.6761799387799151129, 0.000000000000000000 ) ) ; +#50633 = FILL_AREA_STYLE ('',( #5600 ) ) ; +#50634 = ORIENTED_EDGE ( 'NONE', *, *, #21917, .T. ) ; +#50635 = EDGE_CURVE ( 'NONE', #14803, #33080, #12090, .T. ) ; +#50636 = LINE ( 'NONE', #97999, #27671 ) ; +#50637 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #28159, #53143, #36817, #6099 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#50639 = FACE_OUTER_BOUND ( 'NONE', #22938, .T. ) ; +#50638 = CARTESIAN_POINT ( 'NONE', ( -1.147487226257349890, -1.445368494507049961, 0.8299999999999998490 ) ) ; +#50640 = CARTESIAN_POINT ( 'NONE', ( 0.9002637987012980236, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#50641 = PRESENTATION_STYLE_ASSIGNMENT (( #27660 ) ) ; +#50642 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1115, 'distance_accuracy_value', 'NONE'); +#50643 = ORIENTED_EDGE ( 'NONE', *, *, #4514, .F. ) ; +#50644 = EDGE_CURVE ( 'NONE', #21886, #93467, #3316, .T. ) ; +#50645 = FILL_AREA_STYLE_COLOUR ( '', #66850 ) ; +#50646 = CYLINDRICAL_SURFACE ( 'NONE', #96396, 0.04999999999999999584 ) ; +#50647 = CARTESIAN_POINT ( 'NONE', ( -1.143806093516799960, -0.9548508715965600135, 0.8299999999999999600 ) ) ; +#50648 = CARTESIAN_POINT ( 'NONE', ( 7.661837875124987818, 2.155857124875012243, 0.8648700000000000276 ) ) ; +#50649 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.149999999999970157, 0.000000000000000000 ) ) ; +#50650 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8648700000000000276 ) ) ; +#50651 = AXIS2_PLACEMENT_3D ( 'NONE', #96266, #5328, #18664 ) ; +#50652 = AXIS2_PLACEMENT_3D ( 'NONE', #94190, #17100, #55949 ) ; +#50653 = EDGE_CURVE ( 'NONE', #53326, #61497, #98848, .T. ) ; +#50654 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50655 = FILL_AREA_STYLE ('',( #66445 ) ) ; +#50656 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #81106, #37141 ), + ( #90744, #83095 ), + ( #29938, #36146 ), + ( #59146, #99320 ), + ( #74438, #51474 ), + ( #20796, #13057 ), + ( #52969, #82599 ), + ( #44752, #13558 ), + ( #75922, #98327 ), + ( #67741, #98815 ), + ( #90237, #5431 ), + ( #44256, #66748 ), + ( #53460, #12564 ), + ( #97845, #27984 ), + ( #60628, #75420 ), + ( #68239, #43768 ), + ( #74933, #4946 ), + ( #28958, #28468 ), + ( #60145, #21294 ), + ( #52454, #83602 ), + ( #91725, #21795 ), + ( #84084, #14092 ), + ( #45244, #37640 ), + ( #68734, #99785 ), + ( #84578, #14595 ), + ( #86090, #93709 ), + ( #7395, #24346 ), + ( #39130, #69750 ), + ( #77934, #6891 ), + ( #7899, #39636 ), + ( #92709, #16118 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.03814092977640389653, 0.07324469314986049862, 0.1061969321809869971, 0.1374304763707679955, 0.1678896035485339944, 0.1977315896515779992, 0.2280232376912230130, 0.2586940336098749738, 0.2899912476047389887, 0.3221726268997229803, 0.3550576746715989884, 0.3890409003039089764, 0.4584870114880090219, 0.5284665488555919666, 0.5980717268930320074, 0.6665294321140310396, 0.6996665789640289512, 0.7315154747723879858, 0.7619337275606480331, 0.7912372011617729850, 0.8192113105742789836, 0.8457594638444070334, 0.8709908791189390209, 0.8957711837317919867, 0.9201022408770099803, 0.9449582991602709647, 0.9714845733685939511, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#50657 = AXIS2_PLACEMENT_3D ( 'NONE', #5924, #99788, #61136 ) ; +#50658 = STYLED_ITEM ( 'NONE', ( #52351 ), #93604 ) ; +#50659 = FILL_AREA_STYLE_COLOUR ( '', #100665 ) ; +#50660 = ORIENTED_EDGE ( 'NONE', *, *, #15073, .F. ) ; +#50661 = SURFACE_STYLE_USAGE ( .BOTH. , #36326 ) ; +#50662 = ORIENTED_EDGE ( 'NONE', *, *, #100664, .F. ) ; +#50663 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83151, 'distance_accuracy_value', 'NONE'); +#50664 = FILL_AREA_STYLE_COLOUR ( '', #97709 ) ; +#50665 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#50666 = CARTESIAN_POINT ( 'NONE', ( -0.2259284465094109906, -1.087576819458450084, 0.8100000000000000533 ) ) ; +#50667 = SURFACE_SIDE_STYLE ('',( #20489 ) ) ; +#50668 = AXIS2_PLACEMENT_3D ( 'NONE', #55747, #73574, #72070 ) ; +#50669 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#50670 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, -0.2250000000000000333 ) ) ; +#50671 = CYLINDRICAL_SURFACE ( 'NONE', #61561, 1.319494367338009955 ) ; +#50672 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#50673 = VECTOR ( 'NONE', #97939, 1000.000000000000000 ) ; +#50674 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50675 = ORIENTED_EDGE ( 'NONE', *, *, #99603, .F. ) ; +#50676 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#50677 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#50678 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39260 ), #27862 ) ; +#50679 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50680 = VERTEX_POINT ( 'NONE', #38174 ) ; +#50681 = FILL_AREA_STYLE_COLOUR ( '', #72920 ) ; +#50682 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36939 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10970, #3412, #35074 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50683 = ORIENTED_EDGE ( 'NONE', *, *, #79386, .F. ) ; +#50684 = ADVANCED_FACE ( 'NONE', ( #45282 ), #23354, .F. ) ; +#50685 = ADVANCED_FACE ( 'NONE', ( #83131 ), #14128, .T. ) ; +#50686 = FILL_AREA_STYLE_COLOUR ( '', #1169 ) ; +#50687 = PLANE ( 'NONE', #96815 ) ; +#50688 = SURFACE_STYLE_USAGE ( .BOTH. , #35863 ) ; +#50689 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50691 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11430 ), #9825 ) ; +#50692 = ORIENTED_EDGE ( 'NONE', *, *, #97957, .T. ) ; +#50693 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78295 ), #66978 ) ; +#50694 = FACE_OUTER_BOUND ( 'NONE', #6127, .T. ) ; +#50695 = ORIENTED_EDGE ( 'NONE', *, *, #30772, .T. ) ; +#50696 = PRESENTATION_STYLE_ASSIGNMENT (( #89476 ) ) ; +#50697 = ORIENTED_EDGE ( 'NONE', *, *, #88206, .T. ) ; +#50698 = EDGE_CURVE ( 'NONE', #40173, #31830, #100814, .T. ) ; +#50699 = EDGE_LOOP ( 'NONE', ( #58884, #57655, #74136, #51576, #52371, #80207, #89858, #7126, #40053, #32211, #58604, #58, #3504, #41087, #40492, #35257, #39724, #61735, #92514, #12776, #95090, #81597, #91338, #15973, #90870, #15227, #83108, #79203, #17644, #97852, #72814, #4774, #24752, #60591, #84807, #93180, #98056, #35635, #92047, #24313, #53270, #48427, #80985, #100401, #41539, #21641, #17977, #6644, #43392, #83384, #8898, #42140, #96336, #59178, #75657, #69732, #3216, #26851, #44837, #76705 ) ) ; +#50700 = SURFACE_STYLE_USAGE ( .BOTH. , #91966 ) ; +#50701 = FACE_OUTER_BOUND ( 'NONE', #33212, .T. ) ; +#50702 = PRESENTATION_STYLE_ASSIGNMENT (( #2713 ) ) ; +#50703 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#50704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31138 ) ) ; +#50706 = FILL_AREA_STYLE_COLOUR ( '', #4397 ) ; +#50705 = CARTESIAN_POINT ( 'NONE', ( 0.3500290314248439838, -0.9624968822990390693, 0.8100000000000000533 ) ) ; +#50707 = ORIENTED_EDGE ( 'NONE', *, *, #24573, .F. ) ; +#50708 = EDGE_CURVE ( 'NONE', #28835, #80455, #50267, .T. ) ; +#50710 = ORIENTED_EDGE ( 'NONE', *, *, #93435, .F. ) ; +#50709 = EDGE_LOOP ( 'NONE', ( #51832, #6223, #68311, #21414 ) ) ; +#50711 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822763000000000133, 0.8991599999999999593 ) ) ; +#50712 = ORIENTED_EDGE ( 'NONE', *, *, #39387, .T. ) ; +#50713 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84914 ), #11442 ) ; +#50714 = VECTOR ( 'NONE', #44959, 1000.000000000000000 ) ; +#50715 = ORIENTED_EDGE ( 'NONE', *, *, #21418, .T. ) ; +#50717 = ORIENTED_EDGE ( 'NONE', *, *, #95845, .F. ) ; +#50716 = SURFACE_STYLE_USAGE ( .BOTH. , #60388 ) ; +#50718 = EDGE_CURVE ( 'NONE', #76102, #45362, #89036, .T. ) ; +#50719 = FACE_OUTER_BOUND ( 'NONE', #71947, .T. ) ; +#50720 = ORIENTED_EDGE ( 'NONE', *, *, #39699, .T. ) ; +#50721 = PLANE ( 'NONE', #6746 ) ; +#50722 = VERTEX_POINT ( 'NONE', #40193 ) ; +#50723 = CYLINDRICAL_SURFACE ( 'NONE', #31849, 0.009999999999999998473 ) ; +#50724 = MANIFOLD_SOLID_BREP ( 'ÊäÈë85', #91042 ) ; +#50725 = ADVANCED_FACE ( 'NONE', ( #70301 ), #32539, .F. ) ; +#50726 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#50727 = FACE_OUTER_BOUND ( 'NONE', #69094, .T. ) ; +#50728 = STYLED_ITEM ( 'NONE', ( #78452 ), #17979 ) ; +#50729 = FILL_AREA_STYLE ('',( #27243 ) ) ; +#50730 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50731 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59542, #19160, #11429 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50732 = CARTESIAN_POINT ( 'NONE', ( 1.706409873422509937, -1.445184491613219935, 0.8100000000000000533 ) ) ; +#50733 = EDGE_CURVE ( 'NONE', #2385, #67996, #31321, .T. ) ; +#50734 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55684 ), #53978 ) ; +#50736 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50735 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50737 = PRESENTATION_STYLE_ASSIGNMENT (( #80868 ) ) ; +#50739 = EDGE_CURVE ( 'NONE', #43148, #50605, #16153, .T. ) ; +#50738 = CARTESIAN_POINT ( 'NONE', ( -0.2257747756978046860, -1.073058171074661837, 0.8100000000001369438 ) ) ; +#50740 = VERTEX_POINT ( 'NONE', #24385 ) ; +#50741 = VECTOR ( 'NONE', #80746, 1000.000000000000000 ) ; +#50742 = LINE ( 'NONE', #27252, #22362 ) ; +#50743 = VECTOR ( 'NONE', #91777, 1000.000000000000000 ) ; +#50744 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2399999999999999911 ) ) ; +#50745 = VECTOR ( 'NONE', #29846, 1000.000000000000000 ) ; +#50746 = FILL_AREA_STYLE_COLOUR ( '', #25699 ) ; +#50748 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50747 = CARTESIAN_POINT ( 'NONE', ( 0.3985040481619670505, -0.9698512957057280337, 0.8299999999999999600 ) ) ; +#50749 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50750 = SURFACE_STYLE_FILL_AREA ( #10304 ) ; +#50751 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94705 ), #24738 ) ; +#50752 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50753 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14740 ), #1763 ) ; +#50754 = CARTESIAN_POINT ( 'NONE', ( -0.1238200612200840572, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#50755 = ORIENTED_EDGE ( 'NONE', *, *, #54028, .T. ) ; +#50756 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50757 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#50758 = FACE_OUTER_BOUND ( 'NONE', #96380, .T. ) ; +#50759 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50760 = VERTEX_POINT ( 'NONE', #55530 ) ; +#50761 = SURFACE_STYLE_FILL_AREA ( #88025 ) ; +#50762 = EDGE_CURVE ( 'NONE', #79240, #53421, #57933, .T. ) ; +#50763 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50765 = FACE_BOUND ( 'NONE', #76924, .T. ) ; +#50764 = LINE ( 'NONE', #4751, #52349 ) ; +#50766 = CARTESIAN_POINT ( 'NONE', ( 1.581863761282799929, -1.087576819458450084, 0.8299999999999999600 ) ) ; +#50767 = VECTOR ( 'NONE', #87353, 1000.000000000000000 ) ; +#50768 = CARTESIAN_POINT ( 'NONE', ( -0.1995248675705779962, -1.417598257925390293, 0.8100000000000000533 ) ) ; +#50769 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#50770 = PRESENTATION_STYLE_ASSIGNMENT (( #99109 ) ) ; +#50771 = VECTOR ( 'NONE', #98342, 1000.000000000000000 ) ; +#50772 = ORIENTED_EDGE ( 'NONE', *, *, #44221, .T. ) ; +#50773 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50774 = EDGE_CURVE ( 'NONE', #60878, #11603, #66053, .T. ) ; +#50775 = CYLINDRICAL_SURFACE ( 'NONE', #64200, 0.05000000000000012768 ) ; +#50776 = LINE ( 'NONE', #41586, #31045 ) ; +#50777 = CARTESIAN_POINT ( 'NONE', ( 0.9823626554959720147, -1.038425069758839969, 0.8299999999999994049 ) ) ; +#50778 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#50779 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.05000000000000071, 0.000000000000000000 ) ) ; +#50780 = SURFACE_STYLE_USAGE ( .BOTH. , #88046 ) ; +#50781 = LINE ( 'NONE', #91050, #99576 ) ; +#50782 = EDGE_CURVE ( 'NONE', #81116, #5418, #78980, .T. ) ; +#50783 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50784 = STYLED_ITEM ( 'NONE', ( #2460 ), #46271 ) ; +#50785 = SURFACE_STYLE_FILL_AREA ( #28281 ) ; +#50786 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50787 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.09999999999999870104, -9.095983544939292593E-90 ) ) ; +#50788 = VERTEX_POINT ( 'NONE', #60431 ) ; +#50789 = ORIENTED_EDGE ( 'NONE', *, *, #27649, .F. ) ; +#50790 = CIRCLE ( 'NONE', #36127, 0.009999999999999998473 ) ; +#50791 = MANIFOLD_SOLID_BREP ( 'ÊäÈë100', #98966 ) ; +#50792 = SURFACE_SIDE_STYLE ('',( #13378 ) ) ; +#50793 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#50794 = PLANE ( 'NONE', #50466 ) ; +#50795 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.099999999999960121, 0.000000000000000000 ) ) ; +#50796 = PRESENTATION_STYLE_ASSIGNMENT (( #45074 ) ) ; +#50797 = EDGE_LOOP ( 'NONE', ( #44358, #76812, #8255, #97083 ) ) ; +#50798 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#50799 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50800 = SURFACE_SIDE_STYLE ('',( #95185 ) ) ; +#50801 = VECTOR ( 'NONE', #56844, 1000.000000000000000 ) ; +#50802 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#50803 = EDGE_LOOP ( 'NONE', ( #59670, #38236, #76191, #47545 ) ) ; +#50804 = LINE ( 'NONE', #96698, #11811 ) ; +#50805 = EDGE_CURVE ( 'NONE', #95525, #5298, #68022, .T. ) ; +#50806 = EDGE_CURVE ( 'NONE', #61653, #70624, #59437, .T. ) ; +#50807 = PRESENTATION_STYLE_ASSIGNMENT (( #19631 ) ) ; +#50808 = VECTOR ( 'NONE', #59414, 1000.000000000000000 ) ; +#50809 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50810 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50811 = ORIENTED_EDGE ( 'NONE', *, *, #38447, .F. ) ; +#50812 = VECTOR ( 'NONE', #9564, 1000.000000000000000 ) ; +#50813 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 8.286473000000000866, 0.8991599999999999593 ) ) ; +#50814 = VECTOR ( 'NONE', #89151, 1000.000000000000000 ) ; +#50815 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#50816 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#50817 = STYLED_ITEM ( 'NONE', ( #71664 ), #7484 ) ; +#50818 = ORIENTED_EDGE ( 'NONE', *, *, #16971, .F. ) ; +#50819 = ADVANCED_FACE ( 'NONE', ( #90532 ), #67523, .T. ) ; +#50820 = FILL_AREA_STYLE_COLOUR ( '', #57826 ) ; +#50821 = SURFACE_SIDE_STYLE ('',( #19646 ) ) ; +#50822 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50824 = VECTOR ( 'NONE', #19755, 1000.000000000000000 ) ; +#50823 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#50825 = STYLED_ITEM ( 'NONE', ( #82774 ), #65975 ) ; +#50826 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50827 = ORIENTED_EDGE ( 'NONE', *, *, #78827, .F. ) ; +#50828 = AXIS2_PLACEMENT_3D ( 'NONE', #25824, #87089, #80444 ) ; +#50829 = VECTOR ( 'NONE', #32366, 1000.000000000000000 ) ; +#50830 = ORIENTED_EDGE ( 'NONE', *, *, #36503, .F. ) ; +#50832 = ORIENTED_EDGE ( 'NONE', *, *, #61523, .T. ) ; +#50831 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50833 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44763, 'distance_accuracy_value', 'NONE'); +#50834 = FILL_AREA_STYLE ('',( #19667 ) ) ; +#50835 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77110 ) ) ; +#50836 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50837 = VERTEX_POINT ( 'NONE', #28737 ) ; +#50838 = PRESENTATION_STYLE_ASSIGNMENT (( #60511 ) ) ; +#50839 = DIRECTION ( 'NONE', ( -2.356961244533699997E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50840 = AXIS2_PLACEMENT_3D ( 'NONE', #15542, #15019, #16054 ) ; +#50841 = EDGE_LOOP ( 'NONE', ( #61636, #47039, #57003, #90175 ) ) ; +#50842 = LINE ( 'NONE', #11424, #33922 ) ; +#50843 = ORIENTED_EDGE ( 'NONE', *, *, #45382, .F. ) ; +#50844 = AXIS2_PLACEMENT_3D ( 'NONE', #48177, #24206, #55356 ) ; +#50846 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#50845 = FILL_AREA_STYLE_COLOUR ( '', #38173 ) ; +#50847 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.5000000000000015543, 7.477407789112982559E-79 ) ) ; +#50848 = EDGE_CURVE ( 'NONE', #87112, #8017, #91034, .T. ) ; +#50849 = ORIENTED_EDGE ( 'NONE', *, *, #44498, .T. ) ; +#50850 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#50851 = ORIENTED_EDGE ( 'NONE', *, *, #1264, .T. ) ; +#50852 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50853 = ORIENTED_EDGE ( 'NONE', *, *, #28914, .F. ) ; +#50854 = LINE ( 'NONE', #20681, #68220 ) ; +#50855 = SURFACE_SIDE_STYLE ('',( #50379 ) ) ; +#50856 = CARTESIAN_POINT ( 'NONE', ( -1.180619344033760010, -1.219266740403220028, 0.8299999999999999600 ) ) ; +#50857 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000000222, 3.123820061220075051, 0.000000000000000000 ) ) ; +#50858 = LINE ( 'NONE', #3864, #3559 ) ; +#50859 = DIRECTION ( 'NONE', ( -0.7071075504167442238, 0.7071060119555140355, 0.000000000000000000 ) ) ; +#50860 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999902023, 3.123820061220065281, 0.000000000000000000 ) ) ; +#50861 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #247 ), #89977 ) ; +#50862 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50863 = VERTEX_POINT ( 'NONE', #11826 ) ; +#50864 = DIRECTION ( 'NONE', ( 1.000000000000000000, -2.168404344971010051E-15, 0.000000000000000000 ) ) ; +#50865 = LINE ( 'NONE', #20187, #95286 ) ; +#50866 = EDGE_CURVE ( 'NONE', #83734, #65265, #52747, .T. ) ; +#50867 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#50870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50869 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#50868 = FACE_OUTER_BOUND ( 'NONE', #37471, .T. ) ; +#50872 = SURFACE_STYLE_FILL_AREA ( #83874 ) ; +#50871 = STYLED_ITEM ( 'NONE', ( #71258 ), #58801 ) ; +#50873 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21220, 'distance_accuracy_value', 'NONE'); +#50874 = FACE_OUTER_BOUND ( 'NONE', #71008, .T. ) ; +#50875 = VECTOR ( 'NONE', #16523, 1000.000000000000000 ) ; +#50876 = VECTOR ( 'NONE', #59135, 1000.000000000000000 ) ; +#50877 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50878 = LINE ( 'NONE', #97291, #38748 ) ; +#50879 = PLANE ( 'NONE', #14098 ) ; +#50880 = VERTEX_POINT ( 'NONE', #74218 ) ; +#50881 = ADVANCED_FACE ( 'NONE', ( #68532 ), #27268, .T. ) ; +#50882 = AXIS2_PLACEMENT_3D ( 'NONE', #35300, #58287, #19435 ) ; +#50883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50884 = SURFACE_STYLE_USAGE ( .BOTH. , #65677 ) ; +#50885 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#50886 = PRESENTATION_STYLE_ASSIGNMENT (( #78477 ) ) ; +#50887 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50888 = CARTESIAN_POINT ( 'NONE', ( 0.4190707317248760222, -1.180616848856389955, 0.8300000000000015143 ) ) ; +#50889 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72724 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41853, #17838, #55185 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50890 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, -6.018531076210109988E-33 ) ) ; +#50891 = PLANE ( 'NONE', #44082 ) ; +#50892 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50893 = FACE_OUTER_BOUND ( 'NONE', #95445, .T. ) ; +#50894 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50895 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96137, #32384, #57393, #63546 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#50896 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50897 = SURFACE_STYLE_USAGE ( .BOTH. , #26905 ) ; +#50898 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65505 ), #19893 ) ; +#50899 = FILL_AREA_STYLE ('',( #12990 ) ) ; +#50900 = SURFACE_SIDE_STYLE ('',( #82535 ) ) ; +#50901 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50902 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, -3.500000000000000444, 0.000000000000000000 ) ) ; +#50903 = ADVANCED_FACE ( 'NONE', ( #30730 ), #100565, .T. ) ; +#50904 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28083 ) ) ; +#50905 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#50906 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#50907 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#50908 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#50909 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16311 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72241, #33971, #88559 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50911 = EDGE_CURVE ( 'NONE', #86316, #90877, #14881, .T. ) ; +#50910 = SURFACE_STYLE_USAGE ( .BOTH. , #76358 ) ; +#50912 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#50913 = ORIENTED_EDGE ( 'NONE', *, *, #3117, .T. ) ; +#50914 = FILL_AREA_STYLE_COLOUR ( '', #38843 ) ; +#50915 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999689, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#50916 = FILL_AREA_STYLE_COLOUR ( '', #5283 ) ; +#50917 = STYLED_ITEM ( 'NONE', ( #9222 ), #52117 ) ; +#50919 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8648700000000000276 ) ) ; +#50918 = FILL_AREA_STYLE ('',( #82056 ) ) ; +#50920 = FILL_AREA_STYLE_COLOUR ( '', #34501 ) ; +#50921 = EDGE_CURVE ( 'NONE', #7232, #26599, #24130, .T. ) ; +#50922 = ADVANCED_FACE ( 'NONE', ( #31760 ), #46025, .T. ) ; +#50923 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50924 = CARTESIAN_POINT ( 'NONE', ( 1.076179938779914913, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#50925 = VERTEX_POINT ( 'NONE', #33803 ) ; +#50926 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#50927 = ADVANCED_FACE ( 'NONE', ( #17429 ), #96033, .T. ) ; +#50928 = ADVANCED_FACE ( 'NONE', ( #25153 ), #57290, .T. ) ; +#50929 = FILL_AREA_STYLE ('',( #66707 ) ) ; +#50930 = FILL_AREA_STYLE ('',( #19765 ) ) ; +#50931 = EDGE_LOOP ( 'NONE', ( #32137, #40742, #15860, #89214 ) ) ; +#50932 = ORIENTED_EDGE ( 'NONE', *, *, #45822, .F. ) ; +#50933 = ADVANCED_FACE ( 'NONE', ( #64927 ), #71072, .T. ) ; +#50934 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35112 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25385, #57539, #70805 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50935 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61577 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83942, #13939, #18748 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#50936 = FILL_AREA_STYLE_COLOUR ( '', #45496 ) ; +#50937 = SURFACE_STYLE_FILL_AREA ( #14059 ) ; +#50938 = EDGE_LOOP ( 'NONE', ( #57830, #11575, #62961, #75650, #90642, #12658, #13246, #10345 ) ) ; +#50939 = CARTESIAN_POINT ( 'NONE', ( 1.821320548784939986, -1.306448053922619978, 0.8299999999999999600 ) ) ; +#50940 = SURFACE_SIDE_STYLE ('',( #27443 ) ) ; +#50941 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50942 = AXIS2_PLACEMENT_3D ( 'NONE', #79341, #25729, #66024 ) ; +#50943 = CARTESIAN_POINT ( 'NONE', ( -1.162261078148919990, -0.8845231535185279492, 0.8299999999999997380 ) ) ; +#50944 = CIRCLE ( 'NONE', #76996, 0.1679250012421869831 ) ; +#50945 = EDGE_CURVE ( 'NONE', #37825, #15997, #48099, .T. ) ; +#50946 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #35225, #41033 ) ; +#50948 = ORIENTED_EDGE ( 'NONE', *, *, #100623, .F. ) ; +#50947 = VERTEX_POINT ( 'NONE', #40450 ) ; +#50949 = VERTEX_POINT ( 'NONE', #71586 ) ; +#50950 = VERTEX_POINT ( 'NONE', #63926 ) ; +#50951 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #94062 ) ; +#50952 = CARTESIAN_POINT ( 'NONE', ( 1.877211804471180079, -1.084027901463999966, 0.8299999999999995159 ) ) ; +#50953 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3634, 'distance_accuracy_value', 'NONE'); +#50954 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#50955 = CARTESIAN_POINT ( 'NONE', ( 1.865911170909900108, -1.438073744133560039, 0.8100000000000000533 ) ) ; +#50957 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -2.100000000000000533, 0.8299999999999999600 ) ) ; +#50956 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#50958 = ORIENTED_EDGE ( 'NONE', *, *, #28185, .T. ) ; +#50959 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608240111, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#50960 = CARTESIAN_POINT ( 'NONE', ( -1.175853632737690058, -0.8847374564574109757, 0.8100000000000000533 ) ) ; +#50961 = EDGE_LOOP ( 'NONE', ( #82858, #98907, #89641, #80081 ) ) ; +#50962 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 4.524664999999999715, 0.8991599999999999593 ) ) ; +#50963 = VERTEX_POINT ( 'NONE', #75110 ) ; +#50964 = ORIENTED_EDGE ( 'NONE', *, *, #34669, .T. ) ; +#50965 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#50966 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73762 ) ) ; +#50967 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50968 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50970 = EDGE_CURVE ( 'NONE', #14361, #57374, #42939, .T. ) ; +#50969 = PLANE ( 'NONE', #99436 ) ; +#50972 = VERTEX_POINT ( 'NONE', #3643 ) ; +#50971 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#50973 = PRESENTATION_STYLE_ASSIGNMENT (( #12057 ) ) ; +#50974 = EDGE_LOOP ( 'NONE', ( #59914, #82626, #4199, #96105 ) ) ; +#50975 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#50976 = FILL_AREA_STYLE_COLOUR ( '', #60435 ) ; +#50977 = EDGE_LOOP ( 'NONE', ( #95486, #41380, #80997, #83365 ) ) ; +#50978 = FILL_AREA_STYLE_COLOUR ( '', #82832 ) ; +#50980 = ORIENTED_EDGE ( 'NONE', *, *, #13156, .T. ) ; +#50979 = AXIS2_PLACEMENT_3D ( 'NONE', #10231, #81325, #65976 ) ; +#50981 = EDGE_CURVE ( 'NONE', #270, #51654, #66923, .T. ) ; +#50982 = ORIENTED_EDGE ( 'NONE', *, *, #84061, .F. ) ; +#50984 = FILL_AREA_STYLE_COLOUR ( '', #11136 ) ; +#50983 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#50985 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20587, #51763, #12860, #72717 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#50986 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#50987 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#50988 = CARTESIAN_POINT ( 'NONE', ( -0.3688379042909170069, -1.119121047813059988, 0.8100000000000000533 ) ) ; +#50990 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19975 ) ) ; +#50989 = SURFACE_SIDE_STYLE ('',( #28488 ) ) ; +#50991 = FILL_AREA_STYLE ('',( #19826 ) ) ; +#50992 = SURFACE_STYLE_USAGE ( .BOTH. , #11062 ) ; +#50993 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71721, 'distance_accuracy_value', 'NONE'); +#50994 = ORIENTED_EDGE ( 'NONE', *, *, #26470, .F. ) ; +#50995 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#50996 = ORIENTED_EDGE ( 'NONE', *, *, #60630, .T. ) ; +#50997 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#50998 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.000000000000000000, -11.57000000000000028 ) ) ; +#50999 = FILL_AREA_STYLE_COLOUR ( '', #46742 ) ; +#51000 = FACE_OUTER_BOUND ( 'NONE', #30194, .T. ) ; +#51001 = PRESENTATION_STYLE_ASSIGNMENT (( #96404 ) ) ; +#51002 = CIRCLE ( 'NONE', #70560, 0.02999999999999997113 ) ; +#51003 = STYLED_ITEM ( 'NONE', ( #54793 ), #35654 ) ; +#51004 = FACE_OUTER_BOUND ( 'NONE', #17630, .T. ) ; +#51005 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51006 = EDGE_LOOP ( 'NONE', ( #50348, #77205, #19294, #96875 ) ) ; +#51007 = ADVANCED_FACE ( 'NONE', ( #5604 ), #97032, .T. ) ; +#51008 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51009 = FILL_AREA_STYLE_COLOUR ( '', #34148 ) ; +#51011 = AXIS2_PLACEMENT_3D ( 'NONE', #23736, #52867, #22212 ) ; +#51010 = CARTESIAN_POINT ( 'NONE', ( 0.2049220250908939944, -0.9740213618777919802, 0.8100000000000010525 ) ) ; +#51012 = VECTOR ( 'NONE', #98971, 1000.000000000000000 ) ; +#51013 = FACE_OUTER_BOUND ( 'NONE', #94883, .T. ) ; +#51014 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#51016 = LINE ( 'NONE', #50020, #53283 ) ; +#51015 = AXIS2_PLACEMENT_3D ( 'NONE', #13311, #74190, #4237 ) ; +#51017 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5471, 'distance_accuracy_value', 'NONE'); +#51018 = STYLED_ITEM ( 'NONE', ( #52735 ), #87152 ) ; +#51019 = STYLED_ITEM ( 'NONE', ( #53277 ), #36424 ) ; +#51020 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51021 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51022 = PRESENTATION_STYLE_ASSIGNMENT (( #19849 ) ) ; +#51023 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#51024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52818 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1602, #57768, #47540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51025 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000541, 0.1350000000000000089 ) ) ; +#51026 = CARTESIAN_POINT ( 'NONE', ( 1.342785358116189931, -1.072184731453450057, 0.8299999999999995159 ) ) ; +#51027 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#51028 = ORIENTED_EDGE ( 'NONE', *, *, #38301, .F. ) ; +#51029 = LINE ( 'NONE', #20859, #69686 ) ; +#51030 = CARTESIAN_POINT ( 'NONE', ( 1.531892641499219998, -0.9966931238414048488, 0.8299999999999999600 ) ) ; +#51031 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51032 = ORIENTED_EDGE ( 'NONE', *, *, #34363, .T. ) ; +#51033 = FACE_OUTER_BOUND ( 'NONE', #22778, .T. ) ; +#51034 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#51035 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55131, #70931, #33136, #23462 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51036 = VECTOR ( 'NONE', #10742, 999.9999999999998863 ) ; +#51037 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51038 = AXIS2_PLACEMENT_3D ( 'NONE', #57476, #88585, #72262 ) ; +#51039 = FACE_OUTER_BOUND ( 'NONE', #20258, .T. ) ; +#51040 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51041 = VERTEX_POINT ( 'NONE', #83765 ) ; +#51042 = ORIENTED_EDGE ( 'NONE', *, *, #20072, .F. ) ; +#51043 = LINE ( 'NONE', #96444, #87859 ) ; +#51044 = VECTOR ( 'NONE', #85598, 1000.000000000000000 ) ; +#51045 = SURFACE_STYLE_USAGE ( .BOTH. , #74520 ) ; +#51046 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#51047 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51048 = EDGE_CURVE ( 'NONE', #35659, #61697, #50636, .T. ) ; +#51049 = LINE ( 'NONE', #5025, #12635 ) ; +#51050 = CARTESIAN_POINT ( 'NONE', ( -0.7059659090909090606, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#51051 = STYLED_ITEM ( 'NONE', ( #57212 ), #52871 ) ; +#51052 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51053 = MANIFOLD_SOLID_BREP ( 'ÊäÈë122', #72912 ) ; +#51054 = ORIENTED_EDGE ( 'NONE', *, *, #36166, .F. ) ; +#51055 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #24436, #86690, #63738, #80562 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51056 = VECTOR ( 'NONE', #17434, 1000.000000000000000 ) ; +#51057 = STYLED_ITEM ( 'NONE', ( #32443 ), #52516 ) ; +#51058 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51059 = VERTEX_POINT ( 'NONE', #61310 ) ; +#51060 = SURFACE_STYLE_USAGE ( .BOTH. , #74021 ) ; +#51061 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62585 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23319, #94740, #45740 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51062 = AXIS2_PLACEMENT_3D ( 'NONE', #23395, #92315, #63236 ) ; +#51063 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51064 = ADVANCED_FACE ( 'NONE', ( #488 ), #12223, .T. ) ; +#51065 = CARTESIAN_POINT ( 'NONE', ( -1.056478722217069954, -0.9834456900322131601, 0.8299999999999999600 ) ) ; +#51066 = FACE_OUTER_BOUND ( 'NONE', #39635, .T. ) ; +#51067 = CARTESIAN_POINT ( 'NONE', ( -1.276180882027730279, -0.9985765647821309710, 0.8100000000000010525 ) ) ; +#51068 = FACE_OUTER_BOUND ( 'NONE', #92565, .T. ) ; +#51070 = ORIENTED_EDGE ( 'NONE', *, *, #31489, .F. ) ; +#51069 = ORIENTED_EDGE ( 'NONE', *, *, #70720, .F. ) ; +#51071 = VECTOR ( 'NONE', #42053, 1000.000000000000114 ) ; +#51072 = ORIENTED_EDGE ( 'NONE', *, *, #99212, .F. ) ; +#51073 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#51074 = CIRCLE ( 'NONE', #46108, 0.009999999999999998473 ) ; +#51075 = VECTOR ( 'NONE', #15416, 1000.000000000000000 ) ; +#51077 = FILL_AREA_STYLE_COLOUR ( '', #87079 ) ; +#51076 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#51078 = ORIENTED_EDGE ( 'NONE', *, *, #76768, .F. ) ; +#51079 = AXIS2_PLACEMENT_3D ( 'NONE', #68073, #21634, #36966 ) ; +#51080 = ORIENTED_EDGE ( 'NONE', *, *, #56587, .F. ) ; +#51081 = FILL_AREA_STYLE ('',( #19910 ) ) ; +#51082 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51083 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91769 ) ) ; +#51084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32934 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24525, #18820, #25019 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51085 = SURFACE_STYLE_USAGE ( .BOTH. , #65884 ) ; +#51087 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#51086 = FILL_AREA_STYLE_COLOUR ( '', #59603 ) ; +#51088 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8648700000000000276 ) ) ; +#51089 = ORIENTED_EDGE ( 'NONE', *, *, #95805, .T. ) ; +#51090 = VERTEX_POINT ( 'NONE', #44913 ) ; +#51091 = ORIENTED_EDGE ( 'NONE', *, *, #40778, .F. ) ; +#51092 = VECTOR ( 'NONE', #66346, 1000.000000000000000 ) ; +#51093 = ADVANCED_FACE ( 'NONE', ( #31143 ), #70428, .T. ) ; +#51094 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21686 ) ) ; +#51096 = VERTEX_POINT ( 'NONE', #6079 ) ; +#51095 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.266666666666653285, 3.495651678170078205E-76 ) ) ; +#51097 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#51098 = ORIENTED_EDGE ( 'NONE', *, *, #44625, .F. ) ; +#51099 = SURFACE_SIDE_STYLE ('',( #64886 ) ) ; +#51100 = SURFACE_SIDE_STYLE ('',( #98945 ) ) ; +#51101 = ORIENTED_EDGE ( 'NONE', *, *, #36981, .F. ) ; +#51102 = EDGE_CURVE ( 'NONE', #38666, #52968, #37316, .T. ) ; +#51103 = ORIENTED_EDGE ( 'NONE', *, *, #46689, .T. ) ; +#51104 = FILL_AREA_STYLE ('',( #75563 ) ) ; +#51105 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8648700000000000276 ) ) ; +#51106 = SURFACE_STYLE_FILL_AREA ( #27620 ) ; +#51107 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51108 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61446 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51422, #37599, #90192 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51109 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51110 = SURFACE_STYLE_USAGE ( .BOTH. , #12194 ) ; +#51111 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 6.971255000000000202, 0.8648700000000000276 ) ) ; +#51112 = PRESENTATION_STYLE_ASSIGNMENT (( #49598 ) ) ; +#51113 = CARTESIAN_POINT ( 'NONE', ( 1.531892641499219998, -0.9966931238414048488, 0.8299999999999997380 ) ) ; +#51114 = ORIENTED_EDGE ( 'NONE', *, *, #72630, .F. ) ; +#51115 = CARTESIAN_POINT ( 'NONE', ( -1.105094510553189968, -1.513291690750319995, 0.8100000000000000533 ) ) ; +#51116 = ORIENTED_EDGE ( 'NONE', *, *, #8425, .F. ) ; +#51117 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#51118 = CARTESIAN_POINT ( 'NONE', ( -0.2130180398314890089, -1.488490865982160294, 0.8299999999999999600 ) ) ; +#51119 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.000000000000000000 ) ) ; +#51120 = FACE_OUTER_BOUND ( 'NONE', #72937, .T. ) ; +#51121 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.429870129870129958, 0.8299999999999999600 ) ) ; +#51122 = PRESENTATION_STYLE_ASSIGNMENT (( #98964 ) ) ; +#51123 = EDGE_CURVE ( 'NONE', #1354, #65336, #14766, .T. ) ; +#51124 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51125 = VECTOR ( 'NONE', #25875, 1000.000000000000000 ) ; +#51126 = EDGE_CURVE ( 'NONE', #28356, #51680, #53626, .T. ) ; +#51127 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82103 ), #26639 ) ; +#51128 = FACE_OUTER_BOUND ( 'NONE', #84153, .T. ) ; +#51129 = ORIENTED_EDGE ( 'NONE', *, *, #63698, .T. ) ; +#51131 = LINE ( 'NONE', #13230, #66488 ) ; +#51130 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51132 = SURFACE_STYLE_FILL_AREA ( #19964 ) ; +#51133 = PLANE ( 'NONE', #24086 ) ; +#51134 = AXIS2_PLACEMENT_3D ( 'NONE', #34199, #14650, #37695 ) ; +#51135 = ORIENTED_EDGE ( 'NONE', *, *, #14663, .F. ) ; +#51136 = CARTESIAN_POINT ( 'NONE', ( -1.018373906775690063, -1.409018172687890091, 0.8100000000000000533 ) ) ; +#51137 = ADVANCED_FACE ( 'NONE', ( #9584 ), #95916, .T. ) ; +#51138 = SURFACE_STYLE_USAGE ( .BOTH. , #28152 ) ; +#51139 = EDGE_CURVE ( 'NONE', #95463, #33492, #79643, .T. ) ; +#51140 = CARTESIAN_POINT ( 'NONE', ( -1.010461395130570095, -1.072184731453450057, 0.8299999999999999600 ) ) ; +#51141 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8648700000000000276 ) ) ; +#51142 = SURFACE_STYLE_USAGE ( .BOTH. , #34826 ) ; +#51143 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51144 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51145 = PRESENTATION_STYLE_ASSIGNMENT (( #81792 ) ) ; +#51146 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51148 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51147 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7011 ) ) ; +#51149 = STYLED_ITEM ( 'NONE', ( #22205 ), #37075 ) ; +#51150 = VECTOR ( 'NONE', #5027, 1000.000000000000000 ) ; +#51151 = PLANE ( 'NONE', #24160 ) ; +#51152 = EDGE_LOOP ( 'NONE', ( #17353, #92570, #74829, #66981, #69210, #39788 ) ) ; +#51154 = ORIENTED_EDGE ( 'NONE', *, *, #90629, .F. ) ; +#51153 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24858 ), #60697 ) ; +#51155 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.792553465592259094E-15, 0.000000000000000000 ) ) ; +#51156 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47610, 'distance_accuracy_value', 'NONE'); +#51157 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14907, 'distance_accuracy_value', 'NONE'); +#51158 = SURFACE_STYLE_FILL_AREA ( #52652 ) ; +#51159 = FILL_AREA_STYLE_COLOUR ( '', #39879 ) ; +#51160 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#51161 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51162 = EDGE_CURVE ( 'NONE', #51096, #33665, #28983, .T. ) ; +#51163 = CARTESIAN_POINT ( 'NONE', ( -0.9337505133853444272, 2.302534075926971457, 0.8100000000000000533 ) ) ; +#51164 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51165 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51166 = FILL_AREA_STYLE ('',( #11737 ) ) ; +#51167 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51168 = ORIENTED_EDGE ( 'NONE', *, *, #27768, .T. ) ; +#51169 = LINE ( 'NONE', #72614, #31949 ) ; +#51170 = FILL_AREA_STYLE ('',( #80809 ) ) ; +#51171 = LINE ( 'NONE', #23534, #59163 ) ; +#51172 = EDGE_LOOP ( 'NONE', ( #42528, #46362, #32899, #56715 ) ) ; +#51173 = PLANE ( 'NONE', #27901 ) ; +#51174 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51175 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#51176 = EDGE_LOOP ( 'NONE', ( #50712, #75206, #29691, #100860 ) ) ; +#51177 = LINE ( 'NONE', #41500, #28941 ) ; +#51178 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#51179 = ADVANCED_FACE ( 'NONE', ( #25025 ), #33162, .T. ) ; +#51180 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51181 = FILL_AREA_STYLE_COLOUR ( '', #17226 ) ; +#51183 = VERTEX_POINT ( 'NONE', #94411 ) ; +#51182 = VECTOR ( 'NONE', #84841, 1000.000000000000114 ) ; +#51184 = ORIENTED_EDGE ( 'NONE', *, *, #59672, .F. ) ; +#51185 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51186 = ORIENTED_EDGE ( 'NONE', *, *, #9212, .T. ) ; +#51187 = ORIENTED_EDGE ( 'NONE', *, *, #56266, .T. ) ; +#51188 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4600000000000000200, 0.2349999999999999867 ) ) ; +#51189 = SURFACE_STYLE_FILL_AREA ( #21526 ) ; +#51190 = PRESENTATION_STYLE_ASSIGNMENT (( #3699 ) ) ; +#51191 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10330 ) ) ; +#51192 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51193 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8648700000000000276 ) ) ; +#51194 = EDGE_CURVE ( 'NONE', #63967, #43395, #86780, .T. ) ; +#51196 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51195 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51197 = ORIENTED_EDGE ( 'NONE', *, *, #12720, .F. ) ; +#51198 = ORIENTED_EDGE ( 'NONE', *, *, #93055, .F. ) ; +#51199 = PRESENTATION_STYLE_ASSIGNMENT (( #65483 ) ) ; +#51200 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72373 ) ) ; +#51201 = VERTEX_POINT ( 'NONE', #10576 ) ; +#51202 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51203 = EDGE_CURVE ( 'NONE', #49420, #31588, #41835, .T. ) ; +#51204 = AXIS2_PLACEMENT_3D ( 'NONE', #61793, #16777, #77587 ) ; +#51205 = ORIENTED_EDGE ( 'NONE', *, *, #43935, .T. ) ; +#51206 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #80428, #32953, #18613, #2325 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51208 = ORIENTED_EDGE ( 'NONE', *, *, #18185, .F. ) ; +#51207 = FACE_OUTER_BOUND ( 'NONE', #27694, .T. ) ; +#51209 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#51210 = FILL_AREA_STYLE ('',( #42034 ) ) ; +#51211 = ORIENTED_EDGE ( 'NONE', *, *, #72638, .F. ) ; +#51212 = CARTESIAN_POINT ( 'NONE', ( 4.691989249749913604, 7.954133249749911982, 0.8991599999999999593 ) ) ; +#51214 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#51213 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51215 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#51216 = ORIENTED_EDGE ( 'NONE', *, *, #31853, .F. ) ; +#51217 = EDGE_CURVE ( 'NONE', #92379, #22015, #96417, .T. ) ; +#51218 = MANIFOLD_SOLID_BREP ( 'ÊäÈë114', #77850 ) ; +#51219 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75677 ), #88727 ) ; +#51220 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51221 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96796 ) ) ; +#51222 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51223 = AXIS2_PLACEMENT_3D ( 'NONE', #8358, #16582, #62609 ) ; +#51225 = SURFACE_SIDE_STYLE ('',( #66522 ) ) ; +#51224 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#51226 = VERTEX_POINT ( 'NONE', #13108 ) ; +#51227 = SURFACE_STYLE_FILL_AREA ( #81875 ) ; +#51228 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#51229 = CARTESIAN_POINT ( 'NONE', ( 1.285853239104850054, -1.172828961844079920, 0.8300000000000022915 ) ) ; +#51230 = VECTOR ( 'NONE', #26706, 1000.000000000000000 ) ; +#51231 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8648700000000000276 ) ) ; +#51232 = FILL_AREA_STYLE ('',( #91023 ) ) ; +#51233 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16935 ), #47944 ) ; +#51234 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#51235 = ORIENTED_EDGE ( 'NONE', *, *, #41325, .T. ) ; +#51236 = CIRCLE ( 'NONE', #7102, 0.009999999999999998473 ) ; +#51237 = ADVANCED_FACE ( 'NONE', ( #59203 ), #50021, .T. ) ; +#51238 = EDGE_CURVE ( 'NONE', #46638, #18495, #81156, .T. ) ; +#51239 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51240 = PRESENTATION_STYLE_ASSIGNMENT (( #18560 ) ) ; +#51241 = ORIENTED_EDGE ( 'NONE', *, *, #37377, .T. ) ; +#51242 = LINE ( 'NONE', #69917, #30031 ) ; +#51243 = FILL_AREA_STYLE ('',( #28258 ) ) ; +#51244 = CARTESIAN_POINT ( 'NONE', ( 1.583412716359319905, -1.066507643917919967, 0.8100000000000000533 ) ) ; +#51245 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51246 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#51247 = SURFACE_STYLE_USAGE ( .BOTH. , #3771 ) ; +#51248 = SURFACE_STYLE_FILL_AREA ( #19072 ) ; +#51249 = ORIENTED_EDGE ( 'NONE', *, *, #71966, .T. ) ; +#51250 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#51251 = EDGE_CURVE ( 'NONE', #702, #18846, #44306, .T. ) ; +#51252 = SURFACE_SIDE_STYLE ('',( #97657 ) ) ; +#51253 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#51254 = ADVANCED_FACE ( 'NONE', ( #36692 ), #98376, .F. ) ; +#51255 = LINE ( 'NONE', #43070, #43220 ) ; +#51256 = CARTESIAN_POINT ( 'NONE', ( 0.9994445003280740814, -0.9813977598329840513, 0.8299999999999994049 ) ) ; +#51257 = AXIS2_PLACEMENT_3D ( 'NONE', #52132, #6075, #98972 ) ; +#51258 = PLANE ( 'NONE', #87675 ) ; +#51259 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#51260 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51261 = EDGE_CURVE ( 'NONE', #72731, #39240, #22873, .T. ) ; +#51262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51263 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51264 = VECTOR ( 'NONE', #21493, 1000.000000000000000 ) ; +#51265 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51267 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73348, 'distance_accuracy_value', 'NONE'); +#51268 = ORIENTED_EDGE ( 'NONE', *, *, #39330, .T. ) ; +#51269 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.2000000000000000111, -12.44500000000000028 ) ) ; +#51270 = EDGE_LOOP ( 'NONE', ( #22832, #99657, #58710, #64708 ) ) ; +#51271 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51272 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53805, 'distance_accuracy_value', 'NONE'); +#51273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22119, 'distance_accuracy_value', 'NONE'); +#51274 = FACE_OUTER_BOUND ( 'NONE', #14594, .T. ) ; +#51275 = FILL_AREA_STYLE ('',( #5754 ) ) ; +#51276 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51277 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.6600000000000000311, -0.8000000000000001554 ) ) ; +#51278 = EDGE_CURVE ( 'NONE', #50972, #52613, #61190, .T. ) ; +#51279 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24515, #46930, #48487 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51280 = PRESENTATION_STYLE_ASSIGNMENT (( #57447 ) ) ; +#51281 = VECTOR ( 'NONE', #52392, 1000.000000000000000 ) ; +#51282 = PLANE ( 'NONE', #81032 ) ; +#51283 = LINE ( 'NONE', #4300, #61865 ) ; +#51284 = AXIS2_PLACEMENT_3D ( 'NONE', #50161, #27170, #11724 ) ; +#51285 = LINE ( 'NONE', #12381, #14991 ) ; +#51286 = ORIENTED_EDGE ( 'NONE', *, *, #40324, .F. ) ; +#51287 = CYLINDRICAL_SURFACE ( 'NONE', #17131, 0.04999999999999999584 ) ; +#51288 = FILL_AREA_STYLE ('',( #98645 ) ) ; +#51289 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67526, 'distance_accuracy_value', 'NONE'); +#51292 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48742 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85380, #611, #55283 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51291 = STYLED_ITEM ( 'NONE', ( #93692 ), #38259 ) ; +#51290 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736766344E-18, 0.6700000000000000400, -0.05000000000000000278 ) ) ; +#51293 = STYLED_ITEM ( 'NONE', ( #57552 ), #98623 ) ; +#51294 = ORIENTED_EDGE ( 'NONE', *, *, #98659, .F. ) ; +#51295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51296 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79570 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64532, #88514, #49740 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51297 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51298 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#51299 = ADVANCED_FACE ( 'NONE', ( #91292 ), #22344, .T. ) ; +#51300 = FACE_OUTER_BOUND ( 'NONE', #98079, .T. ) ; +#51302 = EDGE_CURVE ( 'NONE', #99445, #32963, #75977, .T. ) ; +#51301 = CYLINDRICAL_SURFACE ( 'NONE', #3408, 0.05000000000000012768 ) ; +#51303 = PRESENTATION_STYLE_ASSIGNMENT (( #4799 ) ) ; +#51304 = ORIENTED_EDGE ( 'NONE', *, *, #78496, .F. ) ; +#51305 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51306 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23588 ), #59498 ) ; +#51307 = SURFACE_SIDE_STYLE ('',( #12397 ) ) ; +#51308 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44419, 'distance_accuracy_value', 'NONE'); +#51309 = EDGE_CURVE ( 'NONE', #19609, #13072, #7451, .T. ) ; +#51310 = VECTOR ( 'NONE', #82854, 1000.000000000000000 ) ; +#51311 = PRESENTATION_STYLE_ASSIGNMENT (( #20124 ) ) ; +#51312 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990585, 0.000000000000000000 ) ) ; +#51313 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #34332 ) ) ; +#51314 = ORIENTED_EDGE ( 'NONE', *, *, #95509, .T. ) ; +#51315 = CYLINDRICAL_SURFACE ( 'NONE', #78206, 0.009999999999999998473 ) ; +#51316 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.4999999999999994449, 0.1829999999999789850 ) ) ; +#51317 = FILL_AREA_STYLE ('',( #89601 ) ) ; +#51318 = ORIENTED_EDGE ( 'NONE', *, *, #3928, .T. ) ; +#51319 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51320 = EDGE_CURVE ( 'NONE', #25062, #49127, #42197, .T. ) ; +#51321 = ORIENTED_EDGE ( 'NONE', *, *, #33978, .T. ) ; +#51323 = VERTEX_POINT ( 'NONE', #38679 ) ; +#51322 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51324 = PRESENTATION_STYLE_ASSIGNMENT (( #75297 ) ) ; +#51325 = AXIS2_PLACEMENT_3D ( 'NONE', #55179, #39302, #23507 ) ; +#51327 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51326 = SURFACE_SIDE_STYLE ('',( #66618 ) ) ; +#51328 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#51329 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51330 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671291000000000082, 0.8991599999999999593 ) ) ; +#51331 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#51332 = FILL_AREA_STYLE_COLOUR ( '', #99600 ) ; +#51333 = ORIENTED_EDGE ( 'NONE', *, *, #4498, .T. ) ; +#51334 = EDGE_CURVE ( 'NONE', #35165, #55979, #21221, .T. ) ; +#51335 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51336 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51337 = LINE ( 'NONE', #67610, #48283 ) ; +#51338 = ORIENTED_EDGE ( 'NONE', *, *, #68955, .F. ) ; +#51339 = ADVANCED_FACE ( 'NONE', ( #52505 ), #100829, .F. ) ; +#51341 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51340 = SURFACE_SIDE_STYLE ('',( #74806 ) ) ; +#51342 = ORIENTED_EDGE ( 'NONE', *, *, #83046, .T. ) ; +#51343 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70859 ), #7203 ) ; +#51345 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#51344 = SURFACE_STYLE_FILL_AREA ( #51843 ) ; +#51346 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51347 = STYLED_ITEM ( 'NONE', ( #82575 ), #76969 ) ; +#51349 = EDGE_CURVE ( 'NONE', #32846, #72987, #68508, .T. ) ; +#51348 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, 0.000000000000000000 ) ) ; +#51350 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#51351 = AXIS2_PLACEMENT_3D ( 'NONE', #86121, #15128, #24384 ) ; +#51352 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#51353 = VERTEX_POINT ( 'NONE', #79517 ) ; +#51354 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706229E-17, 0.7578679656440356904, -0.2000000000000000111 ) ) ; +#51355 = ORIENTED_EDGE ( 'NONE', *, *, #84540, .F. ) ; +#51356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51357 = STYLED_ITEM ( 'NONE', ( #14160 ), #22268 ) ; +#51359 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#51358 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51360 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#51361 = VECTOR ( 'NONE', #80119, 1000.000000000000000 ) ; +#51362 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51363 = ADVANCED_FACE ( 'NONE', ( #57065 ), #24912, .F. ) ; +#51365 = EDGE_CURVE ( 'NONE', #91854, #38490, #87165, .T. ) ; +#51364 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51366 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#51367 = AXIS2_PLACEMENT_3D ( 'NONE', #56726, #87833, #10119 ) ; +#51368 = CARTESIAN_POINT ( 'NONE', ( 1.199474818244760321, -0.9546485130184679813, 0.8299999999999999600 ) ) ; +#51369 = EDGE_LOOP ( 'NONE', ( #20495, #19243, #75552, #36858 ) ) ; +#51370 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#51373 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51372 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.383333333333330195, 0.000000000000000000 ) ) ; +#51371 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51374 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6568 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55483, #30415, #86076 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51375 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#51376 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1238200612200849871, -0.02000000000000000042 ) ) ; +#51377 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12713, #3626, #42439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51378 = LINE ( 'NONE', #27904, #76178 ) ; +#51379 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51380 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #83819, #30167, #76642, #14813 ), + ( #77657, #67953, #46487, #45964 ), + ( #61369, #21517, #84312, #13274 ), + ( #69466, #60858, #31197, #37371 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#51381 = SURFACE_STYLE_FILL_AREA ( #75339 ) ; +#51382 = VERTEX_POINT ( 'NONE', #79001 ) ; +#51384 = MANIFOLD_SOLID_BREP ( 'ÊäÈë131', #58371 ) ; +#51383 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#51385 = SURFACE_STYLE_USAGE ( .BOTH. , #90147 ) ; +#51386 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#51387 = ADVANCED_FACE ( 'NONE', ( #55549 ), #55031, .T. ) ; +#51388 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, -0.2400000000000000189 ) ) ; +#51389 = FILL_AREA_STYLE ('',( #67177 ) ) ; +#51390 = FACE_OUTER_BOUND ( 'NONE', #73815, .T. ) ; +#51391 = EDGE_CURVE ( 'NONE', #15828, #40780, #35078, .T. ) ; +#51392 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.000000000000000000 ) ) ; +#51393 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51394 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51395 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#51396 = PLANE ( 'NONE', #65314 ) ; +#51397 = LINE ( 'NONE', #82534, #69592 ) ; +#51398 = SURFACE_STYLE_FILL_AREA ( #74860 ) ; +#51399 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51400 = AXIS2_PLACEMENT_3D ( 'NONE', #15668, #38677, #63700 ) ; +#51401 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999922691396, 0.1200000000000000094, -0.3250000000000000666 ) ) ; +#51402 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36107, 'distance_accuracy_value', 'NONE'); +#51403 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43212 ), #20392 ) ; +#51404 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#51405 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#51406 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 7.565224999999999866, 0.8648700000000000276 ) ) ; +#51407 = DIRECTION ( 'NONE', ( 0.7071067811865504593, 0.7071067811865445751, 0.000000000000000000 ) ) ; +#51408 = VERTEX_POINT ( 'NONE', #34068 ) ; +#51409 = SURFACE_STYLE_USAGE ( .BOTH. , #60095 ) ; +#51410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82378 ), #15486 ) ; +#51411 = SURFACE_STYLE_USAGE ( .BOTH. , #90177 ) ; +#51412 = EDGE_CURVE ( 'NONE', #21700, #18774, #48368, .T. ) ; +#51413 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77462, 'distance_accuracy_value', 'NONE'); +#51414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77004 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11649, #26585, #34259 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51416 = SURFACE_STYLE_FILL_AREA ( #52916 ) ; +#51415 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46470 ), #57922 ) ; +#51417 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46761, 'distance_accuracy_value', 'NONE'); +#51418 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49816 ) ) ; +#51419 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97054 ) ) ; +#51420 = CARTESIAN_POINT ( 'NONE', ( -0.09186681814452940520, -0.9637996098261990552, 0.8300000000000002931 ) ) ; +#51421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13792 ), #87242 ) ; +#51422 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51424 = EDGE_CURVE ( 'NONE', #35238, #24110, #43200, .T. ) ; +#51423 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51425 = ORIENTED_EDGE ( 'NONE', *, *, #6005, .F. ) ; +#51426 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51428 = ADVANCED_FACE ( 'NONE', ( #58073 ), #88669, .F. ) ; +#51427 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51429 = ORIENTED_EDGE ( 'NONE', *, *, #67894, .T. ) ; +#51430 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51431 = SURFACE_STYLE_USAGE ( .BOTH. , #48907 ) ; +#51432 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69761, 'distance_accuracy_value', 'NONE'); +#51433 = SURFACE_STYLE_FILL_AREA ( #59617 ) ; +#51434 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82397 ) ) ; +#51435 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62163, 'distance_accuracy_value', 'NONE'); +#51436 = PRESENTATION_STYLE_ASSIGNMENT (( #56714 ) ) ; +#51437 = FILL_AREA_STYLE ('',( #42253 ) ) ; +#51438 = VECTOR ( 'NONE', #6485, 1000.000000000000000 ) ; +#51439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51440 = EDGE_LOOP ( 'NONE', ( #89362, #29564, #17575, #59790 ) ) ; +#51441 = ORIENTED_EDGE ( 'NONE', *, *, #26470, .T. ) ; +#51443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84493 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48848, #64160, #65653 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51442 = AXIS2_PLACEMENT_3D ( 'NONE', #37397, #59895, #68500 ) ; +#51444 = VECTOR ( 'NONE', #14899, 1000.000000000000000 ) ; +#51445 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51446 = PLANE ( 'NONE', #14882 ) ; +#51447 = EDGE_LOOP ( 'NONE', ( #14060, #53472, #3660, #64013 ) ) ; +#51448 = FILL_AREA_STYLE_COLOUR ( '', #11742 ) ; +#51449 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#51450 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50275, #25277, #58444, #17056 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51451 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18824 ), #28597 ) ; +#51452 = SURFACE_STYLE_USAGE ( .BOTH. , #20257 ) ; +#51453 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#51454 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#51456 = VERTEX_POINT ( 'NONE', #74858 ) ; +#51455 = ORIENTED_EDGE ( 'NONE', *, *, #76129, .F. ) ; +#51457 = VERTEX_POINT ( 'NONE', #51891 ) ; +#51458 = ORIENTED_EDGE ( 'NONE', *, *, #71677, .F. ) ; +#51459 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#51460 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, -9.880000000000000782, 0.2999999999999999889 ) ) ; +#51461 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#51463 = CARTESIAN_POINT ( 'NONE', ( 1.220292586642630184, -0.8848558980161149723, 0.8299999999999999600 ) ) ; +#51462 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#51464 = EDGE_CURVE ( 'NONE', #16500, #38776, #66680, .T. ) ; +#51465 = PRESENTATION_STYLE_ASSIGNMENT (( #20273 ) ) ; +#51466 = LINE ( 'NONE', #82590, #75097 ) ; +#51467 = FACE_OUTER_BOUND ( 'NONE', #39089, .T. ) ; +#51468 = ORIENTED_EDGE ( 'NONE', *, *, #55076, .F. ) ; +#51469 = EDGE_CURVE ( 'NONE', #31070, #21443, #86458, .T. ) ; +#51470 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87294 ), #53194 ) ; +#51471 = SURFACE_SIDE_STYLE ('',( #43268 ) ) ; +#51472 = ORIENTED_EDGE ( 'NONE', *, *, #54604, .T. ) ; +#51473 = ORIENTED_EDGE ( 'NONE', *, *, #13848, .F. ) ; +#51474 = CARTESIAN_POINT ( 'NONE', ( 0.9903538716760360572, -1.113830263093820161, 0.8299999999999999600 ) ) ; +#51476 = PRESENTATION_STYLE_ASSIGNMENT (( #97847 ) ) ; +#51475 = LINE ( 'NONE', #37143, #78831 ) ; +#51477 = STYLED_ITEM ( 'NONE', ( #13713 ), #29833 ) ; +#51478 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51479 = ADVANCED_FACE ( 'NONE', ( #27919 ), #51396, .T. ) ; +#51480 = ORIENTED_EDGE ( 'NONE', *, *, #80307, .F. ) ; +#51481 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333322646, -0.1000000000000000056, 0.000000000000000000 ) ) ; +#51482 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.266666666666667052, 0.000000000000000000 ) ) ; +#51483 = VECTOR ( 'NONE', #37155, 1000.000000000000000 ) ; +#51484 = VECTOR ( 'NONE', #20488, 1000.000000000000227 ) ; +#51485 = SURFACE_SIDE_STYLE ('',( #49978 ) ) ; +#51486 = ORIENTED_EDGE ( 'NONE', *, *, #74381, .F. ) ; +#51487 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#51488 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51489 = VERTEX_POINT ( 'NONE', #29395 ) ; +#51490 = EDGE_CURVE ( 'NONE', #81624, #41801, #21723, .T. ) ; +#51491 = EDGE_LOOP ( 'NONE', ( #41205, #33875, #44702, #27733 ) ) ; +#51492 = CARTESIAN_POINT ( 'NONE', ( 0.4642887493627290141, -0.9252028835730660150, 0.8299999999999992939 ) ) ; +#51493 = VECTOR ( 'NONE', #58508, 1000.000000000000000 ) ; +#51494 = PRESENTATION_STYLE_ASSIGNMENT (( #34660 ) ) ; +#51495 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#51496 = STYLED_ITEM ( 'NONE', ( #82592 ), #82644 ) ; +#51497 = STYLED_ITEM ( 'NONE', ( #82895 ), #88977 ) ; +#51498 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51499 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18864 ), #98670 ) ; +#51500 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14406 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94193, #39597, #34488 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51501 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61261 ) ) ; +#51502 = PLANE ( 'NONE', #21746 ) ; +#51504 = ADVANCED_FACE ( 'NONE', ( #69681 ), #5862, .T. ) ; +#51503 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #93187, #23299 ), + ( #15597, #31453 ), + ( #37621, #93685 ), + ( #54958, #73657 ), + ( #2716, #42525 ), + ( #802, #39618 ), + ( #70754, #27721 ), + ( #73170, #33871 ), + ( #81353, #3212 ), + ( #11278, #74167 ), + ( #96102, #3704 ), + ( #58376, #96607 ), + ( #55477, #34876 ), + ( #50214, #64993 ), + ( #47784, #66002 ), + ( #50705, #35393 ), + ( #42020, #10255 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.1277251357949019950, 0.2559383689292250019, 0.3198635178170889937, 0.3822801948528660176, 0.4435287786692460044, 0.5036369928591669654, 0.5632897287285819621, 0.6224265700000809476, 0.6813437883179970234, 0.7410557636720519481, 0.8020398925316100103, 0.8648008806892689693, 0.9302486110852540291, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51505 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51506 = ORIENTED_EDGE ( 'NONE', *, *, #44484, .T. ) ; +#51507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64526 ) ) ; +#51508 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#51509 = VERTEX_POINT ( 'NONE', #62073 ) ; +#51510 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#51511 = ADVANCED_FACE ( 'NONE', ( #30363 ), #22233, .T. ) ; +#51512 = ADVANCED_FACE ( 'NONE', ( #84510 ), #91178, .F. ) ; +#51513 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51514 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51515 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19310 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6103, #100474, #84284 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51516 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51517 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79249 ), #18882 ) ; +#51518 = CYLINDRICAL_SURFACE ( 'NONE', #32206, 0.05000000000000012768 ) ; +#51519 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51520 = VERTEX_POINT ( 'NONE', #15021 ) ; +#51521 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93775 ), #35191 ) ; +#51522 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#51523 = CARTESIAN_POINT ( 'NONE', ( 1.663885285959190163, -1.121518536532950083, 0.8139999999999999458 ) ) ; +#51524 = EDGE_CURVE ( 'NONE', #47955, #70676, #7328, .T. ) ; +#51525 = VECTOR ( 'NONE', #2664, 1000.000000000000000 ) ; +#51526 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51527 = FILL_AREA_STYLE_COLOUR ( '', #10200 ) ; +#51528 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51529 = PLANE ( 'NONE', #1079 ) ; +#51530 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602300000000035, 0.8991599999999999593 ) ) ; +#51531 = LINE ( 'NONE', #3534, #18608 ) ; +#51532 = ADVANCED_FACE ( 'NONE', ( #67666 ), #52389, .F. ) ; +#51533 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59748 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82736, #12714, #35303 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51534 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#51535 = FILL_AREA_STYLE_COLOUR ( '', #45583 ) ; +#51536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51537 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51538 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#51539 = STYLED_ITEM ( 'NONE', ( #37144 ), #3899 ) ; +#51540 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51541 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46595, 'distance_accuracy_value', 'NONE'); +#51542 = ORIENTED_EDGE ( 'NONE', *, *, #9543, .F. ) ; +#51543 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#51544 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.300000000000000266, 1.048695503451051965E-76 ) ) ; +#51545 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#51546 = ORIENTED_EDGE ( 'NONE', *, *, #192, .T. ) ; +#51547 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51548 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51549 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#51550 = LINE ( 'NONE', #71605, #39508 ) ; +#51551 = LINE ( 'NONE', #4530, #21478 ) ; +#51552 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25444 ), #46608 ) ; +#51553 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51554 = FILL_AREA_STYLE_COLOUR ( '', #2667 ) ; +#51555 = STYLED_ITEM ( 'NONE', ( #51739 ), #30159 ) ; +#51556 = ORIENTED_EDGE ( 'NONE', *, *, #16190, .T. ) ; +#51557 = ORIENTED_EDGE ( 'NONE', *, *, #1903, .F. ) ; +#51558 = EDGE_CURVE ( 'NONE', #59301, #72386, #2298, .T. ) ; +#51559 = PRESENTATION_STYLE_ASSIGNMENT (( #51045 ) ) ; +#51560 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#51561 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31531, 'distance_accuracy_value', 'NONE'); +#51563 = LINE ( 'NONE', #60224, #90154 ) ; +#51562 = VECTOR ( 'NONE', #65645, 1000.000000000000000 ) ; +#51564 = VECTOR ( 'NONE', #29171, 1000.000000000000000 ) ; +#51565 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#51566 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26546, 'distance_accuracy_value', 'NONE'); +#51567 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51568 = ADVANCED_FACE ( 'NONE', ( #55921 ), #41104, .T. ) ; +#51569 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#51570 = STYLED_ITEM ( 'NONE', ( #51199 ), #49723 ) ; +#51571 = MANIFOLD_SOLID_BREP ( 'ÊäÈë176', #45309 ) ; +#51572 = PRESENTATION_STYLE_ASSIGNMENT (( #20375 ) ) ; +#51573 = ORIENTED_EDGE ( 'NONE', *, *, #92352, .T. ) ; +#51575 = ORIENTED_EDGE ( 'NONE', *, *, #38351, .T. ) ; +#51574 = VECTOR ( 'NONE', #89121, 1000.000000000000000 ) ; +#51576 = ORIENTED_EDGE ( 'NONE', *, *, #92949, .F. ) ; +#51577 = VECTOR ( 'NONE', #54989, 1000.000000000000000 ) ; +#51578 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#51579 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51580 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999989964, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#51581 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, -8.400000000000000355, -11.32000000000000028 ) ) ; +#51584 = ORIENTED_EDGE ( 'NONE', *, *, #43204, .F. ) ; +#51583 = ORIENTED_EDGE ( 'NONE', *, *, #12573, .T. ) ; +#51582 = ADVANCED_FACE ( 'NONE', ( #49257 ), #55426, .T. ) ; +#51585 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75528 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13735, #59312, #67410 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51586 = ORIENTED_EDGE ( 'NONE', *, *, #20345, .T. ) ; +#51587 = DIRECTION ( 'NONE', ( 0.7071045084557434635, 0.7071090539100467476, 0.000000000000000000 ) ) ; +#51588 = STYLED_ITEM ( 'NONE', ( #78141 ), #15725 ) ; +#51590 = SURFACE_STYLE_FILL_AREA ( #92809 ) ; +#51589 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51591 = ORIENTED_EDGE ( 'NONE', *, *, #98702, .F. ) ; +#51592 = ORIENTED_EDGE ( 'NONE', *, *, #14052, .F. ) ; +#51594 = AXIS2_PLACEMENT_3D ( 'NONE', #18777, #81621, #11556 ) ; +#51593 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, -5.403663627667755085E-17, -0.8499999999999999778 ) ) ; +#51595 = AXIS2_PLACEMENT_3D ( 'NONE', #83281, #68432, #20987 ) ; +#51596 = SURFACE_STYLE_USAGE ( .BOTH. , #50085 ) ; +#51597 = FACE_OUTER_BOUND ( 'NONE', #17991, .T. ) ; +#51598 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#51599 = ORIENTED_EDGE ( 'NONE', *, *, #72528, .F. ) ; +#51600 = ORIENTED_EDGE ( 'NONE', *, *, #53297, .F. ) ; +#51601 = STYLED_ITEM ( 'NONE', ( #69826 ), #5102 ) ; +#51602 = ORIENTED_EDGE ( 'NONE', *, *, #38356, .T. ) ; +#51603 = PLANE ( 'NONE', #95210 ) ; +#51604 = FILL_AREA_STYLE_COLOUR ( '', #44440 ) ; +#51605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77651 ), #7450 ) ; +#51606 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#51607 = CIRCLE ( 'NONE', #35351, 0.009999999999999998473 ) ; +#51608 = EDGE_CURVE ( 'NONE', #8138, #67140, #65557, .T. ) ; +#51610 = ORIENTED_EDGE ( 'NONE', *, *, #99352, .T. ) ; +#51609 = FACE_OUTER_BOUND ( 'NONE', #90358, .T. ) ; +#51611 = EDGE_LOOP ( 'NONE', ( #14891, #16852, #17509, #6515, #27610, #8923 ) ) ; +#51612 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#51613 = ORIENTED_EDGE ( 'NONE', *, *, #40846, .F. ) ; +#51614 = EDGE_CURVE ( 'NONE', #31325, #21132, #96183, .T. ) ; +#51615 = ORIENTED_EDGE ( 'NONE', *, *, #80043, .T. ) ; +#51616 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51617 = FACE_OUTER_BOUND ( 'NONE', #57239, .T. ) ; +#51618 = SURFACE_SIDE_STYLE ('',( #82731 ) ) ; +#51619 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87443 ), #77670 ) ; +#51620 = EDGE_CURVE ( 'NONE', #88972, #72098, #72725, .T. ) ; +#51621 = FILL_AREA_STYLE_COLOUR ( '', #47157 ) ; +#51622 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.000000000000000000 ) ) ; +#51623 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17389 ) ) ; +#51624 = VERTEX_POINT ( 'NONE', #50292 ) ; +#51625 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#51626 = VERTEX_POINT ( 'NONE', #80404 ) ; +#51627 = FILL_AREA_STYLE ('',( #98957 ) ) ; +#51628 = ADVANCED_FACE ( 'NONE', ( #49775 ), #3291, .T. ) ; +#51629 = EDGE_CURVE ( 'NONE', #2363, #49449, #24402, .T. ) ; +#51630 = SURFACE_STYLE_FILL_AREA ( #28609 ) ; +#51631 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#51632 = VECTOR ( 'NONE', #85996, 1000.000000000000000 ) ; +#51633 = FILL_AREA_STYLE_COLOUR ( '', #84418 ) ; +#51635 = FILL_AREA_STYLE ('',( #15646 ) ) ; +#51634 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#51636 = FILL_AREA_STYLE_COLOUR ( '', #25896 ) ; +#51637 = FILL_AREA_STYLE_COLOUR ( '', #76139 ) ; +#51638 = FILL_AREA_STYLE_COLOUR ( '', #70647 ) ; +#51639 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51640 = LINE ( 'NONE', #67412, #14937 ) ; +#51641 = EDGE_CURVE ( 'NONE', #35369, #436, #884, .T. ) ; +#51642 = SURFACE_STYLE_USAGE ( .BOTH. , #50141 ) ; +#51643 = SURFACE_SIDE_STYLE ('',( #58806 ) ) ; +#51644 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37963 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89633, #81990, #20166 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51645 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51646 = ADVANCED_FACE ( 'NONE', ( #7449 ), #31017, .F. ) ; +#51647 = ORIENTED_EDGE ( 'NONE', *, *, #95659, .T. ) ; +#51648 = FILL_AREA_STYLE ('',( #52635 ) ) ; +#51649 = FACE_OUTER_BOUND ( 'NONE', #17117, .T. ) ; +#51650 = STYLED_ITEM ( 'NONE', ( #94775 ), #62206 ) ; +#51651 = PRESENTATION_STYLE_ASSIGNMENT (( #5607 ) ) ; +#51652 = AXIS2_PLACEMENT_3D ( 'NONE', #89814, #19873, #4540 ) ; +#51653 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59457, 'distance_accuracy_value', 'NONE'); +#51654 = VERTEX_POINT ( 'NONE', #86658 ) ; +#51655 = CARTESIAN_POINT ( 'NONE', ( -0.9926480063939780996, -1.365766081162230083, 0.8299999999999999600 ) ) ; +#51656 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.429870129870129958, 0.8299999999999999600 ) ) ; +#51658 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8222 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13066, #23329, #72680 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51657 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#51659 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84208 ), #45031 ) ; +#51660 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#51661 = PRESENTATION_STYLE_ASSIGNMENT (( #20470 ) ) ; +#51662 = FILL_AREA_STYLE_COLOUR ( '', #70313 ) ; +#51663 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51664 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#51665 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#51666 = VERTEX_POINT ( 'NONE', #23369 ) ; +#51667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51668 = ORIENTED_EDGE ( 'NONE', *, *, #15151, .T. ) ; +#51669 = STYLED_ITEM ( 'NONE', ( #34409 ), #4464 ) ; +#51670 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73409, 'distance_accuracy_value', 'NONE'); +#51671 = PLANE ( 'NONE', #37431 ) ; +#51672 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#51673 = CARTESIAN_POINT ( 'NONE', ( -0.1181104512869620010, -0.9624218420162741205, 0.8299999999999999600 ) ) ; +#51674 = VECTOR ( 'NONE', #11399, 1000.000000000000114 ) ; +#51675 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#51676 = PRESENTATION_STYLE_ASSIGNMENT (( #52171 ) ) ; +#51677 = PRESENTATION_STYLE_ASSIGNMENT (( #29175 ) ) ; +#51678 = LINE ( 'NONE', #76127, #42905 ) ; +#51679 = ADVANCED_FACE ( 'NONE', ( #54528 ), #24911, .F. ) ; +#51680 = VERTEX_POINT ( 'NONE', #46302 ) ; +#51681 = ORIENTED_EDGE ( 'NONE', *, *, #92893, .T. ) ; +#51682 = STYLED_ITEM ( 'NONE', ( #79545 ), #12288 ) ; +#51683 = ORIENTED_EDGE ( 'NONE', *, *, #35218, .T. ) ; +#51684 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42243 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60294, #25011, #33669 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51685 = LINE ( 'NONE', #7105, #87042 ) ; +#51686 = AXIS2_PLACEMENT_3D ( 'NONE', #78583, #63803, #86766 ) ; +#51687 = FILL_AREA_STYLE_COLOUR ( '', #68664 ) ; +#51688 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999990452, -0.02000000000001254941 ) ) ; +#51689 = EDGE_LOOP ( 'NONE', ( #20774, #19530, #64344, #24139 ) ) ; +#51690 = SURFACE_STYLE_FILL_AREA ( #90972 ) ; +#51691 = ORIENTED_EDGE ( 'NONE', *, *, #93009, .F. ) ; +#51692 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#51693 = AXIS2_PLACEMENT_3D ( 'NONE', #3414, #19729, #34578 ) ; +#51694 = VECTOR ( 'NONE', #35692, 1000.000000000000000 ) ; +#51695 = VERTEX_POINT ( 'NONE', #78483 ) ; +#51697 = EDGE_CURVE ( 'NONE', #20411, #8603, #87164, .T. ) ; +#51696 = EDGE_LOOP ( 'NONE', ( #20439, #89087, #85585, #81610 ) ) ; +#51698 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92173 ) ) ; +#51699 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51700 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51701 = SURFACE_SIDE_STYLE ('',( #28207 ) ) ; +#51702 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51703 = ORIENTED_EDGE ( 'NONE', *, *, #72470, .T. ) ; +#51704 = ORIENTED_EDGE ( 'NONE', *, *, #45250, .F. ) ; +#51705 = ORIENTED_EDGE ( 'NONE', *, *, #54382, .F. ) ; +#51706 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#51707 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69587 ) ) ; +#51709 = EDGE_LOOP ( 'NONE', ( #39001, #92111, #37612, #9796 ) ) ; +#51708 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51710 = VECTOR ( 'NONE', #47250, 1000.000000000000000 ) ; +#51711 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#51712 = FACE_OUTER_BOUND ( 'NONE', #73909, .T. ) ; +#51713 = ORIENTED_EDGE ( 'NONE', *, *, #39430, .T. ) ; +#51714 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#51715 = ORIENTED_EDGE ( 'NONE', *, *, #11152, .T. ) ; +#51716 = EDGE_CURVE ( 'NONE', #11725, #21864, #94789, .T. ) ; +#51717 = MANIFOLD_SOLID_BREP ( 'ÊäÈë14', #66485 ) ; +#51718 = STYLED_ITEM ( 'NONE', ( #25016 ), #39590 ) ; +#51719 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51720 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51721 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51722 = SURFACE_STYLE_FILL_AREA ( #90499 ) ; +#51723 = VECTOR ( 'NONE', #30648, 1000.000000000000000 ) ; +#51724 = LINE ( 'NONE', #81866, #55815 ) ; +#51725 = CARTESIAN_POINT ( 'NONE', ( 1.807266337641940002, -1.389839611604140046, 0.8299999999999999600 ) ) ; +#51727 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51726 = PLANE ( 'NONE', #46287 ) ; +#51728 = FACE_OUTER_BOUND ( 'NONE', #62829, .T. ) ; +#51729 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#51730 = ORIENTED_EDGE ( 'NONE', *, *, #74425, .T. ) ; +#51731 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#51733 = EDGE_CURVE ( 'NONE', #67005, #79973, #34067, .T. ) ; +#51732 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82694 ) ) ; +#51734 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51735 = CARTESIAN_POINT ( 'NONE', ( 1.164415487177949959, -1.144973971495400145, 0.8300000000000022915 ) ) ; +#51737 = PRESENTATION_STYLE_ASSIGNMENT (( #44529 ) ) ; +#51736 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#51738 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#51739 = PRESENTATION_STYLE_ASSIGNMENT (( #82375 ) ) ; +#51740 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#51741 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.000000000000000000 ) ) ; +#51742 = FILL_AREA_STYLE ('',( #13333 ) ) ; +#51743 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51744 = ORIENTED_EDGE ( 'NONE', *, *, #58868, .F. ) ; +#51745 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#51746 = EDGE_CURVE ( 'NONE', #73310, #19502, #26904, .T. ) ; +#51747 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#51748 = ORIENTED_EDGE ( 'NONE', *, *, #89298, .F. ) ; +#51749 = CARTESIAN_POINT ( 'NONE', ( 8.227523124874956295, 9.806752875125043900, 0.8648700000000000276 ) ) ; +#51750 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#51751 = FILL_AREA_STYLE ('',( #36423 ) ) ; +#51752 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51753 = CARTESIAN_POINT ( 'NONE', ( 1.680683372326140068, -0.9625852181168450539, 0.8299999999999999600 ) ) ; +#51754 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51755 = FILL_AREA_STYLE_COLOUR ( '', #8749 ) ; +#51756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #400 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19086, #42594, #12798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51757 = AXIS2_PLACEMENT_3D ( 'NONE', #66673, #90672, #49888 ) ; +#51758 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#51759 = VERTEX_POINT ( 'NONE', #81556 ) ; +#51760 = PLANE ( 'NONE', #71807 ) ; +#51761 = AXIS2_PLACEMENT_3D ( 'NONE', #89057, #56438, #25776 ) ; +#51762 = SURFACE_SIDE_STYLE ('',( #91047 ) ) ; +#51763 = CARTESIAN_POINT ( 'NONE', ( -2.366666666666666696, -3.500000000000000000, 0.000000000000000000 ) ) ; +#51764 = CARTESIAN_POINT ( 'NONE', ( 1.031909709261459973, -1.462480703074420019, 0.8300000000000010703 ) ) ; +#51765 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51766 = FILL_AREA_STYLE_COLOUR ( '', #31112 ) ; +#51767 = LINE ( 'NONE', #91053, #7620 ) ; +#51768 = CYLINDRICAL_SURFACE ( 'NONE', #41511, 0.01000000000000002623 ) ; +#51769 = AXIS2_PLACEMENT_3D ( 'NONE', #90741, #74930, #3483 ) ; +#51770 = VECTOR ( 'NONE', #41095, 1000.000000000000000 ) ; +#51771 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#51772 = ORIENTED_EDGE ( 'NONE', *, *, #91119, .F. ) ; +#51773 = LINE ( 'NONE', #27803, #8892 ) ; +#51774 = EDGE_LOOP ( 'NONE', ( #17450, #43983, #68286, #55712 ) ) ; +#51775 = MANIFOLD_SOLID_BREP ( 'ÊäÈë86', #92477 ) ; +#51776 = CARTESIAN_POINT ( 'NONE', ( 1.121762993838200106, -0.9661431204389000493, 0.8299999999999999600 ) ) ; +#51777 = LINE ( 'NONE', #82916, #47826 ) ; +#51779 = VECTOR ( 'NONE', #90582, 1000.000000000000000 ) ; +#51778 = CYLINDRICAL_SURFACE ( 'NONE', #81983, 0.04999999999999991257 ) ; +#51780 = SURFACE_SIDE_STYLE ('',( #35971 ) ) ; +#51781 = CARTESIAN_POINT ( 'NONE', ( 1.812952947087890232, -0.9302426320460149833, 0.8100000000000000533 ) ) ; +#51782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72980 ) ) ; +#51783 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#51784 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.000000000000000000 ) ) ; +#51785 = CLOSED_SHELL ( 'NONE', ( #96898, #44415, #36521, #94486, #19425, #88413 ) ) ; +#51786 = ADVANCED_FACE ( 'NONE', ( #19203 ), #2410, .T. ) ; +#51787 = VERTEX_POINT ( 'NONE', #12989 ) ; +#51788 = LINE ( 'NONE', #74759, #48137 ) ; +#51789 = SURFACE_SIDE_STYLE ('',( #74259 ) ) ; +#51790 = STYLED_ITEM ( 'NONE', ( #17676 ), #39857 ) ; +#51791 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82756 ) ) ; +#51792 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#51793 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#51794 = VERTEX_POINT ( 'NONE', #67665 ) ; +#51795 = CIRCLE ( 'NONE', #90922, 0.1200000000000000927 ) ; +#51796 = LINE ( 'NONE', #37968, #45097 ) ; +#51797 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51798 = PRESENTATION_STYLE_ASSIGNMENT (( #52305 ) ) ; +#51799 = PRESENTATION_STYLE_ASSIGNMENT (( #83438 ) ) ; +#51800 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.004999999999999987094, -0.1500000000000000222 ) ) ; +#51801 = EDGE_LOOP ( 'NONE', ( #43786, #58127, #19392, #15475 ) ) ; +#51802 = PLANE ( 'NONE', #90605 ) ; +#51803 = LINE ( 'NONE', #73769, #66809 ) ; +#51804 = SURFACE_STYLE_FILL_AREA ( #43120 ) ; +#51805 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51806 = EDGE_LOOP ( 'NONE', ( #41564, #53952, #85321, #100870 ) ) ; +#51807 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#51808 = LINE ( 'NONE', #75774, #16202 ) ; +#51809 = AXIS2_PLACEMENT_3D ( 'NONE', #5151, #60358, #66472 ) ; +#51810 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#51811 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2850000000000000311, 0.000000000000000000 ) ) ; +#51812 = VECTOR ( 'NONE', #89041, 1000.000000000000000 ) ; +#51813 = SURFACE_STYLE_FILL_AREA ( #81474 ) ; +#51814 = VERTEX_POINT ( 'NONE', #36577 ) ; +#51815 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#51816 = EDGE_CURVE ( 'NONE', #30427, #91043, #68671, .T. ) ; +#51817 = CIRCLE ( 'NONE', #30621, 0.1000000000000000056 ) ; +#51818 = ORIENTED_EDGE ( 'NONE', *, *, #45910, .F. ) ; +#51820 = ORIENTED_EDGE ( 'NONE', *, *, #94715, .T. ) ; +#51819 = LINE ( 'NONE', #5292, #42692 ) ; +#51821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6112 ) ) ; +#51822 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83844, 'distance_accuracy_value', 'NONE'); +#51823 = CARTESIAN_POINT ( 'NONE', ( 0.5854301948051939819, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#51825 = CARTESIAN_POINT ( 'NONE', ( -1.303498337670309981, -1.475020827802409951, 0.8100000000000000533 ) ) ; +#51824 = CARTESIAN_POINT ( 'NONE', ( -1.303800513451622844, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#51826 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#51827 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.250000000000000000, 0.000000000000000000 ) ) ; +#51828 = VERTEX_POINT ( 'NONE', #29394 ) ; +#51829 = SURFACE_STYLE_FILL_AREA ( #20656 ) ; +#51830 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51831 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#51832 = ORIENTED_EDGE ( 'NONE', *, *, #2807, .F. ) ; +#51833 = ADVANCED_FACE ( 'NONE', ( #28396 ), #37077, .T. ) ; +#51834 = CARTESIAN_POINT ( 'NONE', ( 1.309875304108520044, -1.500691070757680157, 0.8100000000000000533 ) ) ; +#51835 = EDGE_CURVE ( 'NONE', #52994, #88427, #42311, .T. ) ; +#51836 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51837 = SURFACE_STYLE_FILL_AREA ( #20662 ) ; +#51838 = ORIENTED_EDGE ( 'NONE', *, *, #84979, .T. ) ; +#51839 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51840 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#51841 = ORIENTED_EDGE ( 'NONE', *, *, #52928, .F. ) ; +#51842 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95818 ) ) ; +#51844 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#51843 = FILL_AREA_STYLE ('',( #28836 ) ) ; +#51845 = SURFACE_SIDE_STYLE ('',( #4838 ) ) ; +#51846 = VECTOR ( 'NONE', #79775, 1000.000000000000000 ) ; +#51847 = AXIS2_PLACEMENT_3D ( 'NONE', #15676, #7952, #31533 ) ; +#51848 = PLANE ( 'NONE', #89148 ) ; +#51849 = VECTOR ( 'NONE', #24579, 1000.000000000000000 ) ; +#51850 = SURFACE_STYLE_FILL_AREA ( #15380 ) ; +#51851 = EDGE_LOOP ( 'NONE', ( #97647, #76420, #6779, #7113 ) ) ; +#51853 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99704 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6382, #20763, #51439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51852 = CARTESIAN_POINT ( 'NONE', ( 1.238543046823479932, -1.444732071753930036, 0.8299999999999999600 ) ) ; +#51854 = VERTEX_POINT ( 'NONE', #83023 ) ; +#51855 = FILL_AREA_STYLE_COLOUR ( '', #66633 ) ; +#51856 = CLOSED_SHELL ( 'NONE', ( #79026, #79151, #1627, #100658, #17534, #68450 ) ) ; +#51858 = FILL_AREA_STYLE ('',( #65649 ) ) ; +#51857 = SURFACE_STYLE_USAGE ( .BOTH. , #20682 ) ; +#51859 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78750 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92400, #62306, #53628 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51860 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000541, 0.1350000000000000089 ) ) ; +#51861 = VECTOR ( 'NONE', #29049, 1000.000000000000000 ) ; +#51862 = LINE ( 'NONE', #73827, #6788 ) ; +#51863 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48663 ), #76310 ) ; +#51864 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#51865 = CARTESIAN_POINT ( 'NONE', ( 1.322240070112479904, -1.010360997253880067, 0.8100000000000000533 ) ) ; +#51866 = SURFACE_STYLE_FILL_AREA ( #53853 ) ; +#51867 = ORIENTED_EDGE ( 'NONE', *, *, #20316, .F. ) ; +#51868 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51869 = AXIS2_PLACEMENT_3D ( 'NONE', #4597, #10672, #50608 ) ; +#51870 = EDGE_CURVE ( 'NONE', #16963, #55200, #53381, .T. ) ; +#51873 = PLANE ( 'NONE', #34607 ) ; +#51872 = FACE_OUTER_BOUND ( 'NONE', #58519, .T. ) ; +#51871 = FILL_AREA_STYLE ('',( #20702 ) ) ; +#51874 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20879, 'distance_accuracy_value', 'NONE'); +#51875 = DIRECTION ( 'NONE', ( 1.000000000000000000, 6.179952383168509971E-14, 0.000000000000000000 ) ) ; +#51876 = FILL_AREA_STYLE ('',( #52878 ) ) ; +#51877 = EDGE_LOOP ( 'NONE', ( #39626, #82349, #17883, #44226 ) ) ; +#51879 = MANIFOLD_SOLID_BREP ( 'ÊäÈë177', #92543 ) ; +#51878 = SURFACE_SIDE_STYLE ('',( #91648 ) ) ; +#51880 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000444, 0.000000000000000000 ) ) ; +#51881 = FACE_OUTER_BOUND ( 'NONE', #56877, .T. ) ; +#51882 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#51883 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #34332, .NOT_KNOWN. ) ; +#51884 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4849999999999999867, -0.2500000000000000000 ) ) ; +#51885 = PLANE ( 'NONE', #93700 ) ; +#51886 = STYLED_ITEM ( 'NONE', ( #10141 ), #74614 ) ; +#51887 = FACE_OUTER_BOUND ( 'NONE', #35651, .T. ) ; +#51888 = PRESENTATION_STYLE_ASSIGNMENT (( #43195 ) ) ; +#51889 = LINE ( 'NONE', #53881, #52804 ) ; +#51890 = CARTESIAN_POINT ( 'NONE', ( -2.216666666666666785, -3.100000000000000533, 0.000000000000000000 ) ) ; +#51891 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.164062568141495335, 0.8299999999999999600 ) ) ; +#51892 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75601 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97653, #35941, #39294 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51893 = ADVANCED_FACE ( 'NONE', ( #74362 ), #22232, .T. ) ; +#51894 = FACE_OUTER_BOUND ( 'NONE', #13424, .T. ) ; +#51895 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59423, #20563, #45027, #44530 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#51896 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#51897 = SURFACE_STYLE_USAGE ( .BOTH. , #27403 ) ; +#51898 = VECTOR ( 'NONE', #15560, 1000.000000000000000 ) ; +#51899 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36929, #44077, #38439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51900 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51901 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51902 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#51903 = FACE_OUTER_BOUND ( 'NONE', #77270, .T. ) ; +#51904 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8100000000000000533 ) ) ; +#51905 = EDGE_CURVE ( 'NONE', #14190, #5714, #55425, .T. ) ; +#51906 = EDGE_LOOP ( 'NONE', ( #26083, #40292, #11915, #47360 ) ) ; +#51908 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96730 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76879, #38082, #20228 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51907 = LINE ( 'NONE', #67685, #30719 ) ; +#51909 = FACE_OUTER_BOUND ( 'NONE', #41109, .T. ) ; +#51910 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51912 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51911 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95890 ) ) ; +#51913 = EDGE_CURVE ( 'NONE', #94730, #51794, #81818, .T. ) ; +#51914 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#51915 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24153 ) ) ; +#51916 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51917 = VERTEX_POINT ( 'NONE', #53884 ) ; +#51918 = AXIS2_PLACEMENT_3D ( 'NONE', #98265, #82040, #28891 ) ; +#51919 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51921 = ADVANCED_FACE ( 'NONE', ( #31908 ), #38561, .T. ) ; +#51920 = FILL_AREA_STYLE ('',( #37603 ) ) ; +#51922 = AXIS2_PLACEMENT_3D ( 'NONE', #54506, #2383, #64164 ) ; +#51923 = EDGE_LOOP ( 'NONE', ( #32832, #95361, #76146, #71369, #39225, #74703 ) ) ; +#51924 = SURFACE_SIDE_STYLE ('',( #43235 ) ) ; +#51925 = VECTOR ( 'NONE', #48895, 1000.000000000000000 ) ; +#51926 = PLANE ( 'NONE', #83692 ) ; +#51927 = FILL_AREA_STYLE_COLOUR ( '', #62150 ) ; +#51928 = VECTOR ( 'NONE', #1577, 1000.000000000000000 ) ; +#51929 = VECTOR ( 'NONE', #67748, 1000.000000000000000 ) ; +#51930 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#51931 = ORIENTED_EDGE ( 'NONE', *, *, #11971, .F. ) ; +#51932 = VERTEX_POINT ( 'NONE', #63586 ) ; +#51933 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88301 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6612, #84780, #30639 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51934 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#51935 = VERTEX_POINT ( 'NONE', #94668 ) ; +#51936 = CARTESIAN_POINT ( 'NONE', ( 1.759379393379719936, -1.230342595016630014, 0.8299999999999999600 ) ) ; +#51937 = LINE ( 'NONE', #75896, #36968 ) ; +#51938 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51939 = ADVANCED_FACE ( 'NONE', ( #92639 ), #24789, .T. ) ; +#51940 = ADVANCED_FACE ( 'NONE', ( #50289 ), #18582, .T. ) ; +#51941 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#51942 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #91246, #15637 ) ; +#51943 = FACE_OUTER_BOUND ( 'NONE', #63677, .T. ) ; +#51944 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38879 ) ) ; +#51946 = VERTEX_POINT ( 'NONE', #57954 ) ; +#51945 = EDGE_LOOP ( 'NONE', ( #24210, #43778, #48553, #7599 ) ) ; +#51947 = VERTEX_POINT ( 'NONE', #34457 ) ; +#51948 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67444 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88943, #96057, #50169 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51949 = EDGE_LOOP ( 'NONE', ( #59107, #95620, #92199, #23967, #43602, #73173 ) ) ; +#51950 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000009909, 3.123820061220065281, 0.000000000000000000 ) ) ; +#51951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5278, 'distance_accuracy_value', 'NONE'); +#51952 = SURFACE_SIDE_STYLE ('',( #20782 ) ) ; +#51954 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.149999999999999911, 0.000000000000000000 ) ) ; +#51953 = CARTESIAN_POINT ( 'NONE', ( 0.3671721421540899977, -0.9001501144350020356, 0.8100000000000000533 ) ) ; +#51955 = EDGE_CURVE ( 'NONE', #39774, #63379, #65552, .T. ) ; +#51956 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 7.437945000000000917, 0.8648700000000000276 ) ) ; +#51957 = CARTESIAN_POINT ( 'NONE', ( -0.1525548447364439841, -1.164073081312986924, 0.8100000000000002753 ) ) ; +#51958 = ADVANCED_FACE ( 'NONE', ( #19088 ), #42095, .F. ) ; +#51959 = LINE ( 'NONE', #44424, #29581 ) ; +#51960 = CARTESIAN_POINT ( 'NONE', ( -1.235751819672409990, -0.8946064028769500354, 0.8100000000000000533 ) ) ; +#51961 = VECTOR ( 'NONE', #38196, 1000.000000000000000 ) ; +#51963 = EDGE_LOOP ( 'NONE', ( #81185, #60232, #61221, #46973 ) ) ; +#51962 = STYLED_ITEM ( 'NONE', ( #17260 ), #75046 ) ; +#51964 = FACE_OUTER_BOUND ( 'NONE', #3612, .T. ) ; +#51965 = ORIENTED_EDGE ( 'NONE', *, *, #72548, .F. ) ; +#51966 = ORIENTED_EDGE ( 'NONE', *, *, #50921, .F. ) ; +#51968 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#51967 = FILL_AREA_STYLE ('',( #36147 ) ) ; +#51969 = VERTEX_POINT ( 'NONE', #97182 ) ; +#51970 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#51971 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.5199999999686952812, 0.6999285677528677141 ) ) ; +#51972 = VECTOR ( 'NONE', #29633, 1000.000000000000000 ) ; +#51973 = EDGE_CURVE ( 'NONE', #60642, #48454, #27284, .T. ) ; +#51974 = FILL_AREA_STYLE ('',( #74944 ) ) ; +#51975 = FACE_OUTER_BOUND ( 'NONE', #14280, .T. ) ; +#51976 = EDGE_LOOP ( 'NONE', ( #70406, #92800, #93654, #61463 ) ) ; +#51977 = SURFACE_STYLE_FILL_AREA ( #82610 ) ; +#51978 = SURFACE_STYLE_FILL_AREA ( #91256 ) ; +#51979 = VERTEX_POINT ( 'NONE', #9352 ) ; +#51980 = ORIENTED_EDGE ( 'NONE', *, *, #99814, .T. ) ; +#51982 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, 0.7999999999999999334 ) ) ; +#51981 = CARTESIAN_POINT ( 'NONE', ( 0.4328235538323689791, -0.9111919069839470309, 0.8299999999999992939 ) ) ; +#51984 = STYLED_ITEM ( 'NONE', ( #89082 ), #55854 ) ; +#51983 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#51985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#51987 = ADVANCED_FACE ( 'NONE', ( #99124 ), #52770, .T. ) ; +#51986 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#51988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39974 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4617, #19954, #43434 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51989 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 4.418599000000000387, 0.8648700000000000276 ) ) ; +#51990 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#51991 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18732 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99929, #39259, #29593 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#51992 = EDGE_CURVE ( 'NONE', #31354, #62472, #20593, .T. ) ; +#51993 = ORIENTED_EDGE ( 'NONE', *, *, #60172, .F. ) ; +#51994 = VECTOR ( 'NONE', #73375, 1000.000000000000000 ) ; +#51995 = VECTOR ( 'NONE', #64075, 1000.000000000000000 ) ; +#51996 = ORIENTED_EDGE ( 'NONE', *, *, #90145, .F. ) ; +#51997 = ADVANCED_FACE ( 'NONE', ( #90557 ), #21604, .T. ) ; +#51998 = VECTOR ( 'NONE', #85744, 1000.000000000000000 ) ; +#51999 = PRESENTATION_STYLE_ASSIGNMENT (( #14123 ) ) ; +#52000 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#52001 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10361, #95187, #55941 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52002 = SURFACE_SIDE_STYLE ('',( #13090 ) ) ; +#52003 = PLANE ( 'NONE', #35694 ) ; +#52004 = CYLINDRICAL_SURFACE ( 'NONE', #43616, 0.3000000000000000444 ) ; +#52005 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22599 ) ) ; +#52006 = LINE ( 'NONE', #13094, #76028 ) ; +#52007 = ORIENTED_EDGE ( 'NONE', *, *, #57159, .F. ) ; +#52008 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#52009 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52010 = FILL_AREA_STYLE ('',( #36191 ) ) ; +#52011 = SURFACE_STYLE_USAGE ( .BOTH. , #91773 ) ; +#52012 = STYLED_ITEM ( 'NONE', ( #66538 ), #50819 ) ; +#52013 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52015 = AXIS2_PLACEMENT_3D ( 'NONE', #51401, #81046, #4398 ) ; +#52014 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52016 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52017 = ADVANCED_FACE ( 'NONE', ( #66561 ), #97667, .T. ) ; +#52018 = FACE_OUTER_BOUND ( 'NONE', #69871, .T. ) ; +#52019 = FILL_AREA_STYLE_COLOUR ( '', #86437 ) ; +#52020 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52021 = PLANE ( 'NONE', #49610 ) ; +#52022 = LINE ( 'NONE', #45306, #9425 ) ; +#52023 = ORIENTED_EDGE ( 'NONE', *, *, #34645, .T. ) ; +#52024 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8099999999997948841 ) ) ; +#52025 = FACE_OUTER_BOUND ( 'NONE', #71403, .T. ) ; +#52027 = EDGE_CURVE ( 'NONE', #73258, #51090, #61729, .T. ) ; +#52026 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696238000000000135, 0.8648700000000000276 ) ) ; +#52028 = ORIENTED_EDGE ( 'NONE', *, *, #80889, .T. ) ; +#52029 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#52030 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#52031 = FILL_AREA_STYLE_COLOUR ( '', #44437 ) ; +#52032 = AXIS2_PLACEMENT_3D ( 'NONE', #31413, #23772, #16068 ) ; +#52033 = VECTOR ( 'NONE', #27865, 1000.000000000000000 ) ; +#52034 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#52035 = ADVANCED_FACE ( 'NONE', ( #46046 ), #100100, .T. ) ; +#52036 = CARTESIAN_POINT ( 'NONE', ( 1.407886145087594798, -1.009524776188982287, 0.8099999999999840661 ) ) ; +#52037 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#52038 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73875 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76829, #53352, #38533 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52039 = SURFACE_SIDE_STYLE ('',( #66826 ) ) ; +#52040 = ORIENTED_EDGE ( 'NONE', *, *, #73439, .T. ) ; +#52041 = SURFACE_STYLE_FILL_AREA ( #99388 ) ; +#52042 = EDGE_CURVE ( 'NONE', #15908, #56832, #54271, .T. ) ; +#52043 = FILL_AREA_STYLE ('',( #20874 ) ) ; +#52044 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71573 ) ) ; +#52045 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52046 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#52047 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52048 = FILL_AREA_STYLE ('',( #20373 ) ) ; +#52049 = CARTESIAN_POINT ( 'NONE', ( -1.261679599840822119, -0.9032100794317502457, 0.8100000000000592282 ) ) ; +#52050 = VECTOR ( 'NONE', #33571, 1000.000000000000114 ) ; +#52052 = FILL_AREA_STYLE ('',( #5028 ) ) ; +#52051 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78054 ) ) ; +#52053 = MANIFOLD_SOLID_BREP ( 'ÊäÈë96', #19172 ) ; +#52054 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32028 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79047, #63742, #86176 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52055 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999985359, 0.1400000000000000133 ) ) ; +#52056 = ORIENTED_EDGE ( 'NONE', *, *, #17557, .T. ) ; +#52057 = ORIENTED_EDGE ( 'NONE', *, *, #32609, .T. ) ; +#52058 = VERTEX_POINT ( 'NONE', #6700 ) ; +#52059 = LINE ( 'NONE', #42385, #13356 ) ; +#52060 = FACE_OUTER_BOUND ( 'NONE', #12177, .T. ) ; +#52061 = ADVANCED_FACE ( 'NONE', ( #93524 ), #7701, .T. ) ; +#52062 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52063 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45427 ) ) ; +#52064 = CARTESIAN_POINT ( 'NONE', ( -0.5417956820186821121, -0.9001291024598061519, 0.8299999999999999600 ) ) ; +#52065 = CARTESIAN_POINT ( 'NONE', ( -1.276180882027730279, -0.9985765647821309710, 0.8299999999999999600 ) ) ; +#52066 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52067 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55357 ) ) ; +#52069 = VERTEX_POINT ( 'NONE', #20361 ) ; +#52068 = VERTEX_POINT ( 'NONE', #64944 ) ; +#52070 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70026 ), #9610 ) ; +#52071 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74863 ) ) ; +#52072 = ORIENTED_EDGE ( 'NONE', *, *, #24532, .F. ) ; +#52073 = CARTESIAN_POINT ( 'NONE', ( 1.519746594691179675, -1.031932509624860161, 0.8099999999999981659 ) ) ; +#52074 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26291, 'distance_accuracy_value', 'NONE'); +#52075 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68213, 'distance_accuracy_value', 'NONE'); +#52077 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52076 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#52078 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24240 ) ) ; +#52079 = ORIENTED_EDGE ( 'NONE', *, *, #10030, .T. ) ; +#52080 = ORIENTED_EDGE ( 'NONE', *, *, #80434, .T. ) ; +#52081 = FILL_AREA_STYLE ('',( #29082 ) ) ; +#52082 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000009645, -0.1400000000000000133 ) ) ; +#52083 = EDGE_CURVE ( 'NONE', #57652, #30965, #17941, .T. ) ; +#52084 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#52086 = FILL_AREA_STYLE ('',( #6525 ) ) ; +#52085 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52087 = FACE_OUTER_BOUND ( 'NONE', #37887, .T. ) ; +#52089 = EDGE_LOOP ( 'NONE', ( #74048, #89823, #41584, #96332 ) ) ; +#52088 = VECTOR ( 'NONE', #9207, 1000.000000000000000 ) ; +#52090 = ORIENTED_EDGE ( 'NONE', *, *, #41747, .F. ) ; +#52091 = VERTEX_POINT ( 'NONE', #95040 ) ; +#52092 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65111 ) ) ; +#52093 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52094 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52097 = ORIENTED_EDGE ( 'NONE', *, *, #32704, .T. ) ; +#52096 = VECTOR ( 'NONE', #86563, 1000.000000000000114 ) ; +#52095 = FILL_AREA_STYLE_COLOUR ( '', #42906 ) ; +#52098 = ORIENTED_EDGE ( 'NONE', *, *, #77794, .T. ) ; +#52099 = CARTESIAN_POINT ( 'NONE', ( 0.01522189160443420189, -1.319025261726090026, 0.8100000000000000533 ) ) ; +#52100 = ORIENTED_EDGE ( 'NONE', *, *, #30942, .T. ) ; +#52101 = EDGE_LOOP ( 'NONE', ( #52436, #30078, #1730, #86470 ) ) ; +#52102 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52103 = SURFACE_STYLE_USAGE ( .BOTH. , #91384 ) ; +#52104 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46596, #96067, #2182 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52105 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52106 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.000000000000000000 ) ) ; +#52107 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.266666666666647068, 0.000000000000000000 ) ) ; +#52108 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6314 ), #29276 ) ; +#52109 = FACE_OUTER_BOUND ( 'NONE', #9512, .T. ) ; +#52110 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70001 ) ) ; +#52111 = SURFACE_STYLE_USAGE ( .BOTH. , #20950 ) ; +#52112 = ORIENTED_EDGE ( 'NONE', *, *, #36073, .T. ) ; +#52113 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#52114 = VERTEX_POINT ( 'NONE', #96558 ) ; +#52115 = EDGE_CURVE ( 'NONE', #56699, #10128, #28049, .T. ) ; +#52116 = VECTOR ( 'NONE', #15867, 1000.000000000000000 ) ; +#52117 = MANIFOLD_SOLID_BREP ( 'ÊäÈë148', #69738 ) ; +#52118 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52119 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41256 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19234, #65730, #15826 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52120 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17826 ) ) ; +#52121 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999908268, 0.2999999999999999334, 0.5799137866959191978 ) ) ; +#52122 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#52123 = EDGE_CURVE ( 'NONE', #84630, #93881, #90302, .T. ) ; +#52125 = LINE ( 'NONE', #14239, #78875 ) ; +#52124 = VECTOR ( 'NONE', #20473, 1000.000000000000000 ) ; +#52126 = PRESENTATION_STYLE_ASSIGNMENT (( #21450 ) ) ; +#52127 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52128 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52129 = FACE_OUTER_BOUND ( 'NONE', #28934, .T. ) ; +#52130 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #87040, #95157, #30882, #25288 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52131 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#52132 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#52133 = STYLED_ITEM ( 'NONE', ( #83390 ), #80431 ) ; +#52134 = FACE_OUTER_BOUND ( 'NONE', #49841, .T. ) ; +#52135 = PRESENTATION_STYLE_ASSIGNMENT (( #59819 ) ) ; +#52136 = EDGE_CURVE ( 'NONE', #30758, #85200, #63467, .T. ) ; +#52138 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52139 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#52140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40711, #9954, #63195 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52141 = FILL_AREA_STYLE_COLOUR ( '', #22372 ) ; +#52142 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53721 ), #9614 ) ; +#52143 = ORIENTED_EDGE ( 'NONE', *, *, #62069, .T. ) ; +#52144 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52145 = EDGE_CURVE ( 'NONE', #20901, #72146, #51550, .T. ) ; +#52146 = FACE_OUTER_BOUND ( 'NONE', #32719, .T. ) ; +#52147 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6327, 'distance_accuracy_value', 'NONE'); +#52148 = FILL_AREA_STYLE_COLOUR ( '', #87388 ) ; +#52149 = FACE_OUTER_BOUND ( 'NONE', #80981, .T. ) ; +#52150 = SURFACE_STYLE_FILL_AREA ( #29632 ) ; +#52151 = CARTESIAN_POINT ( 'NONE', ( 0.4670315120509885287, -1.095045192229049169, 0.8100000000000001643 ) ) ; +#52152 = CARTESIAN_POINT ( 'NONE', ( 1.816666666666666652, -3.099999999999969891, 0.000000000000000000 ) ) ; +#52153 = VECTOR ( 'NONE', #14257, 1000.000000000000000 ) ; +#52154 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#52155 = FILL_AREA_STYLE_COLOUR ( '', #83913 ) ; +#52156 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58719 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57318, #95055, #87424 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52157 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#52158 = ORIENTED_EDGE ( 'NONE', *, *, #100125, .F. ) ; +#52159 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52160 = EDGE_LOOP ( 'NONE', ( #64497, #85677, #18734, #44882 ) ) ; +#52161 = PRESENTATION_STYLE_ASSIGNMENT (( #83792 ) ) ; +#52162 = ADVANCED_FACE ( 'NONE', ( #80790 ), #1664, .T. ) ; +#52163 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27774, 'distance_accuracy_value', 'NONE'); +#52164 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58199, 'distance_accuracy_value', 'NONE'); +#52165 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52166 = FILL_AREA_STYLE_COLOUR ( '', #15345 ) ; +#52167 = CARTESIAN_POINT ( 'NONE', ( -0.1401145506032289989, -0.9647878283071119609, 0.8299999999999999600 ) ) ; +#52168 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52169 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52170 = FILL_AREA_STYLE ('',( #45442 ) ) ; +#52171 = SURFACE_STYLE_USAGE ( .BOTH. , #89451 ) ; +#52172 = LINE ( 'NONE', #74637, #79943 ) ; +#52173 = ADVANCED_FACE ( 'NONE', ( #20864 ), #30007, .T. ) ; +#52174 = ORIENTED_EDGE ( 'NONE', *, *, #16275, .F. ) ; +#52175 = ORIENTED_EDGE ( 'NONE', *, *, #99778, .F. ) ; +#52176 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#52177 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99356 ), #24498 ) ; +#52178 = LINE ( 'NONE', #37361, #67994 ) ; +#52179 = ORIENTED_EDGE ( 'NONE', *, *, #25611, .T. ) ; +#52180 = SURFACE_STYLE_FILL_AREA ( #43990 ) ; +#52181 = ADVANCED_FACE ( 'NONE', ( #68316 ), #30492, .T. ) ; +#52182 = EDGE_CURVE ( 'NONE', #55234, #41918, #83623, .T. ) ; +#52183 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52184 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92842 ), #63557 ) ; +#52185 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#52186 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52188 = VERTEX_POINT ( 'NONE', #6960 ) ; +#52187 = VERTEX_POINT ( 'NONE', #45812 ) ; +#52190 = ADVANCED_FACE ( 'NONE', ( #92775 ), #48410, .T. ) ; +#52189 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52191 = ADVANCED_FACE ( 'NONE', ( #93778 ), #93282, .T. ) ; +#52192 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44215 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43976, #75142, #6113 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52193 = VERTEX_POINT ( 'NONE', #24418 ) ; +#52194 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52196 = DIRECTION ( 'NONE', ( -0.7071067811865484609, 0.7071067811865465735, 0.000000000000000000 ) ) ; +#52195 = FILL_AREA_STYLE_COLOUR ( '', #14765 ) ; +#52197 = ORIENTED_EDGE ( 'NONE', *, *, #13073, .T. ) ; +#52198 = ORIENTED_EDGE ( 'NONE', *, *, #21192, .F. ) ; +#52199 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63695 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95709, #26323, #17612 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52200 = SURFACE_STYLE_FILL_AREA ( #21035 ) ; +#52201 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52202 = EDGE_CURVE ( 'NONE', #79206, #57360, #16677, .T. ) ; +#52203 = CARTESIAN_POINT ( 'NONE', ( -0.5440966885710070144, -1.187196157070490088, 0.8299999999999999600 ) ) ; +#52204 = FILL_AREA_STYLE ('',( #22031 ) ) ; +#52206 = SURFACE_STYLE_USAGE ( .BOTH. , #37868 ) ; +#52205 = SURFACE_STYLE_USAGE ( .BOTH. , #59385 ) ; +#52207 = AXIS2_PLACEMENT_3D ( 'NONE', #5605, #100452, #21464 ) ; +#52208 = ORIENTED_EDGE ( 'NONE', *, *, #56563, .T. ) ; +#52209 = ORIENTED_EDGE ( 'NONE', *, *, #6129, .T. ) ; +#52210 = ORIENTED_EDGE ( 'NONE', *, *, #100393, .F. ) ; +#52211 = EDGE_CURVE ( 'NONE', #59871, #41605, #379, .T. ) ; +#52212 = STYLED_ITEM ( 'NONE', ( #52487 ), #64273 ) ; +#52213 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89787 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92754, #14134, #7442 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52214 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #12210, #19453 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #45717 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#52215 = STYLED_ITEM ( 'NONE', ( #66741 ), #68945 ) ; +#52217 = ORIENTED_EDGE ( 'NONE', *, *, #34927, .T. ) ; +#52216 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#52218 = AXIS2_PLACEMENT_3D ( 'NONE', #23244, #31897, #48245 ) ; +#52219 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52220 = SURFACE_STYLE_USAGE ( .BOTH. , #83346 ) ; +#52221 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#52222 = LINE ( 'NONE', #83348, #100258 ) ; +#52223 = PLANE ( 'NONE', #66808 ) ; +#52224 = ORIENTED_EDGE ( 'NONE', *, *, #96416, .F. ) ; +#52225 = SURFACE_SIDE_STYLE ('',( #76174 ) ) ; +#52226 = SURFACE_STYLE_FILL_AREA ( #98562 ) ; +#52227 = ORIENTED_EDGE ( 'NONE', *, *, #74468, .F. ) ; +#52228 = MANIFOLD_SOLID_BREP ( 'ÊäÈë132', #56688 ) ; +#52229 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, 0.000000000000000000 ) ) ; +#52231 = VECTOR ( 'NONE', #67360, 1000.000000000000000 ) ; +#52230 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52232 = CARTESIAN_POINT ( 'NONE', ( 0.5194035290631999757, -1.172439657072400054, 0.8299999999999999600 ) ) ; +#52233 = PRESENTATION_STYLE_ASSIGNMENT (( #14734 ) ) ; +#52234 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #98098, #90000, #59416, #4728 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52235 = FILL_AREA_STYLE_COLOUR ( '', #30739 ) ; +#52237 = CARTESIAN_POINT ( 'NONE', ( 7.386066041625060308, 7.678361041625021421, 0.8648700000000000276 ) ) ; +#52236 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#52238 = CARTESIAN_POINT ( 'NONE', ( -1.134936903355714621, -1.156541810439597917, 0.8099999999998731548 ) ) ; +#52239 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52240 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.004999999999999999237, 0.2500000000000000000 ) ) ; +#52241 = ORIENTED_EDGE ( 'NONE', *, *, #27003, .F. ) ; +#52242 = EDGE_CURVE ( 'NONE', #59512, #51828, #23908, .T. ) ; +#52243 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4808578643762690952, -0.2500000000000000000 ) ) ; +#52244 = EDGE_CURVE ( 'NONE', #97591, #62724, #48892, .T. ) ; +#52246 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#52245 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52247 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.266666666666659946, 0.000000000000000000 ) ) ; +#52248 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52249 = AXIS2_PLACEMENT_3D ( 'NONE', #20754, #91204, #98781 ) ; +#52250 = SURFACE_STYLE_USAGE ( .BOTH. , #65519 ) ; +#52251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52252 = ORIENTED_EDGE ( 'NONE', *, *, #23756, .F. ) ; +#52253 = PRESENTATION_STYLE_ASSIGNMENT (( #59926 ) ) ; +#52254 = FILL_AREA_STYLE_COLOUR ( '', #69051 ) ; +#52255 = DIRECTION ( 'NONE', ( -2.356961244533699997E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52256 = ORIENTED_EDGE ( 'NONE', *, *, #89288, .T. ) ; +#52257 = STYLED_ITEM ( 'NONE', ( #29138 ), #94998 ) ; +#52258 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#52259 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.000000000000000000 ) ) ; +#52260 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#52261 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86493 ), #88108 ) ; +#52262 = STYLED_ITEM ( 'NONE', ( #74661 ), #85670 ) ; +#52263 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57819 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63426, #2624, #94509 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52264 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52265 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69833 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23945, #46870, #31569 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52266 = ORIENTED_EDGE ( 'NONE', *, *, #90526, .T. ) ; +#52267 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52268 = FILL_AREA_STYLE_COLOUR ( '', #40919 ) ; +#52269 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65849 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47974, #99965, #54651 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52270 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#52271 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#52272 = VECTOR ( 'NONE', #77340, 1000.000000000000000 ) ; +#52273 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, -11.27000000000000135 ) ) ; +#52274 = SURFACE_SIDE_STYLE ('',( #58455 ) ) ; +#52275 = DIRECTION ( 'NONE', ( -0.7071067811865472397, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#52276 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30338, 'distance_accuracy_value', 'NONE'); +#52277 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31043 ), #40918 ) ; +#52278 = SURFACE_STYLE_FILL_AREA ( #90046 ) ; +#52279 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76666 ) ) ; +#52280 = EDGE_LOOP ( 'NONE', ( #50832, #2925, #91355, #57377 ) ) ; +#52281 = LINE ( 'NONE', #51269, #90465 ) ; +#52282 = ORIENTED_EDGE ( 'NONE', *, *, #53849, .F. ) ; +#52283 = SURFACE_STYLE_FILL_AREA ( #67552 ) ; +#52285 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71505, 'distance_accuracy_value', 'NONE'); +#52284 = VECTOR ( 'NONE', #99060, 1000.000000000000000 ) ; +#52286 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52290, 'distance_accuracy_value', 'NONE'); +#52287 = CARTESIAN_POINT ( 'NONE', ( 1.111216736053209919, -0.9708075278790050389, 0.8299999999999999600 ) ) ; +#52288 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52289 = FILL_AREA_STYLE_COLOUR ( '', #85550 ) ; +#52290 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52291 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#52292 = LINE ( 'NONE', #14917, #67917 ) ; +#52293 = LINE ( 'NONE', #74254, #55392 ) ; +#52294 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52295 = VERTEX_POINT ( 'NONE', #42726 ) ; +#52296 = SURFACE_STYLE_USAGE ( .BOTH. , #59973 ) ; +#52297 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#52298 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61533, 'distance_accuracy_value', 'NONE'); +#52299 = SURFACE_STYLE_FILL_AREA ( #98648 ) ; +#52300 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32805 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33568, #86659, #18184 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52301 = VERTEX_POINT ( 'NONE', #19221 ) ; +#52302 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52303 = SURFACE_SIDE_STYLE ('',( #21135 ) ) ; +#52304 = CARTESIAN_POINT ( 'NONE', ( 1.441319620083689967, -1.344945484192040075, 0.8299999999999994049 ) ) ; +#52305 = SURFACE_STYLE_USAGE ( .BOTH. , #20625 ) ; +#52306 = CARTESIAN_POINT ( 'NONE', ( -1.294533524454640094, -1.379057077391790287, 0.8100000000000000533 ) ) ; +#52307 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8648700000000000276 ) ) ; +#52308 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8648700000000000276 ) ) ; +#52309 = ORIENTED_EDGE ( 'NONE', *, *, #72783, .F. ) ; +#52310 = PRESENTATION_STYLE_ASSIGNMENT (( #70998 ) ) ; +#52311 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9117 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65454, #89460, #80300 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52312 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52313 = ADVANCED_FACE ( 'NONE', ( #26921 ), #59086, .T. ) ; +#52314 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1650, 'distance_accuracy_value', 'NONE'); +#52315 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52316 = CARTESIAN_POINT ( 'NONE', ( 1.624720795854639688, -0.9850088450568520448, 0.8099999999999994982 ) ) ; +#52317 = ORIENTED_EDGE ( 'NONE', *, *, #84151, .F. ) ; +#52318 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8179 ) ) ; +#52319 = FACE_OUTER_BOUND ( 'NONE', #64729, .T. ) ; +#52320 = FILL_AREA_STYLE ('',( #35004 ) ) ; +#52321 = ORIENTED_EDGE ( 'NONE', *, *, #60272, .T. ) ; +#52322 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52323 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #83144, #36193 ), + ( #43826, #75472 ), + ( #74979, #67296 ), + ( #20336, #91775 ), + ( #13105, #12611 ), + ( #14141, #98860 ), + ( #29006, #45793 ), + ( #59704, #21849 ), + ( #44303, #44800 ), + ( #52501, #61187 ), + ( #5478, #45294 ), + ( #14640, #6463 ), + ( #60197, #37687 ), + ( #28031, #68781 ), + ( #69265, #83649 ), + ( #99839, #36691 ), + ( #53507, #76975 ), + ( #59198, #90803 ), + ( #90284, #4997 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06674147653962790583, 0.1313279039795479941, 0.1945731643876359995, 0.2562720192966850274, 0.3168036091747580274, 0.3769001200933310147, 0.4368671125188500204, 0.4970767235714639853, 0.5566860891065530392, 0.6162465209635079599, 0.6759633994470309881, 0.7368503919440649863, 0.7988039095700789627, 0.8627460748057349527, 0.9299837341856730388, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52324 = VECTOR ( 'NONE', #48207, 1000.000000000000000 ) ; +#52325 = ADVANCED_FACE ( 'NONE', ( #33583 ), #34090, .T. ) ; +#52326 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34322 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6773, #7774, #85472 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52327 = STYLED_ITEM ( 'NONE', ( #37685 ), #95343 ) ; +#52328 = ORIENTED_EDGE ( 'NONE', *, *, #24298, .F. ) ; +#52330 = VERTEX_POINT ( 'NONE', #97794 ) ; +#52329 = LINE ( 'NONE', #4818, #1953 ) ; +#52331 = STYLED_ITEM ( 'NONE', ( #70159 ), #94615 ) ; +#52332 = SURFACE_SIDE_STYLE ('',( #12419 ) ) ; +#52333 = CARTESIAN_POINT ( 'NONE', ( -1.154835151445229968, -1.515412412365080064, 0.8100000000000000533 ) ) ; +#52334 = ORIENTED_EDGE ( 'NONE', *, *, #52679, .F. ) ; +#52335 = SURFACE_STYLE_USAGE ( .BOTH. , #44142 ) ; +#52336 = SURFACE_SIDE_STYLE ('',( #30304 ) ) ; +#52337 = ORIENTED_EDGE ( 'NONE', *, *, #46101, .F. ) ; +#52338 = CARTESIAN_POINT ( 'NONE', ( 1.429960467956949977, -1.401385721107119897, 0.8299999999999999600 ) ) ; +#52339 = FILL_AREA_STYLE ('',( #21169 ) ) ; +#52340 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#52341 = ORIENTED_EDGE ( 'NONE', *, *, #38447, .T. ) ; +#52342 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13104 ), #3441 ) ; +#52344 = SURFACE_SIDE_STYLE ('',( #98697 ) ) ; +#52343 = FACE_OUTER_BOUND ( 'NONE', #92275, .T. ) ; +#52345 = ORIENTED_EDGE ( 'NONE', *, *, #23142, .F. ) ; +#52346 = EDGE_CURVE ( 'NONE', #29149, #68987, #17709, .T. ) ; +#52348 = FACE_OUTER_BOUND ( 'NONE', #69842, .T. ) ; +#52347 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52349 = VECTOR ( 'NONE', #59440, 1000.000000000000000 ) ; +#52350 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.187459415584420030, 0.8099999999999863975 ) ) ; +#52351 = PRESENTATION_STYLE_ASSIGNMENT (( #52839 ) ) ; +#52352 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73612 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86348, #1077, #16874 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52353 = SURFACE_STYLE_USAGE ( .BOTH. , #75312 ) ; +#52354 = EDGE_LOOP ( 'NONE', ( #29863, #87944, #55942, #28670 ) ) ; +#52355 = ORIENTED_EDGE ( 'NONE', *, *, #89479, .F. ) ; +#52356 = EDGE_CURVE ( 'NONE', #17500, #11537, #22251, .T. ) ; +#52358 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#52357 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52359 = PLANE ( 'NONE', #68043 ) ; +#52360 = SURFACE_SIDE_STYLE ('',( #66642 ) ) ; +#52361 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39960 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62578, #24281, #78871 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52362 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52363 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666653285, 0.8999999999999990230, 3.495651678170078205E-76 ) ) ; +#52364 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65380 ), #31141 ) ; +#52367 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52366 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10084 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41512, #27711, #12792 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52368 = FILL_AREA_STYLE_COLOUR ( '', #81312 ) ; +#52369 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52370 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333329751, 2.299999999999999822, 0.000000000000000000 ) ) ; +#52371 = ORIENTED_EDGE ( 'NONE', *, *, #73918, .T. ) ; +#52372 = CARTESIAN_POINT ( 'NONE', ( 1.363204453251209980, -1.351484773706350007, 0.8299999999999994049 ) ) ; +#52374 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#52373 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#52375 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52376 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52377 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, 1.149999999999999911 ) ) ; +#52378 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990585, 0.000000000000000000 ) ) ; +#52379 = EDGE_LOOP ( 'NONE', ( #42024, #14486, #41572, #32503 ) ) ; +#52380 = MANIFOLD_SOLID_BREP ( 'ÊäÈë46', #53366 ) ; +#52381 = ADVANCED_FACE ( 'NONE', ( #83041 ), #37095, .T. ) ; +#52382 = CARTESIAN_POINT ( 'NONE', ( -3.233333333333333393, -3.500000000000000000, 0.000000000000000000 ) ) ; +#52383 = FILL_AREA_STYLE_COLOUR ( '', #19606 ) ; +#52384 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52385 = EDGE_CURVE ( 'NONE', #42170, #39774, #88582, .T. ) ; +#52386 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#52387 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#52388 = AXIS2_PLACEMENT_3D ( 'NONE', #18058, #41594, #43075 ) ; +#52389 = PLANE ( 'NONE', #26279 ) ; +#52390 = LINE ( 'NONE', #75850, #10864 ) ; +#52391 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#52392 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#52393 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32858 ) ) ; +#52394 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52395 = SURFACE_SIDE_STYLE ('',( #83535 ) ) ; +#52396 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47509, 'distance_accuracy_value', 'NONE'); +#52397 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96374 ), #62180 ) ; +#52398 = CARTESIAN_POINT ( 'NONE', ( 1.757815472291410330, -1.145059460293619935, 0.8299999999999997380 ) ) ; +#52399 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#52400 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000081, 0.8991599999999999593 ) ) ; +#52401 = EDGE_CURVE ( 'NONE', #76626, #34733, #91196, .T. ) ; +#52402 = ORIENTED_EDGE ( 'NONE', *, *, #43199, .T. ) ; +#52403 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89610, #11909, #100640 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52404 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#52405 = EDGE_CURVE ( 'NONE', #86972, #18285, #98251, .T. ) ; +#52406 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28155, 'distance_accuracy_value', 'NONE'); +#52407 = SURFACE_STYLE_FILL_AREA ( #90179 ) ; +#52408 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53722, 'distance_accuracy_value', 'NONE'); +#52409 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52410 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45888 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35101, #32185, #24557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52411 = AXIS2_PLACEMENT_3D ( 'NONE', #75124, #5122, #90936 ) ; +#52412 = SURFACE_STYLE_USAGE ( .BOTH. , #21244 ) ; +#52413 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#52414 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#52415 = VERTEX_POINT ( 'NONE', #14038 ) ; +#52416 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59256 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41301, #32120, #87741 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52417 = LINE ( 'NONE', #37602, #74967 ) ; +#52418 = ORIENTED_EDGE ( 'NONE', *, *, #73512, .T. ) ; +#52419 = SURFACE_SIDE_STYLE ('',( #37103 ) ) ; +#52420 = DIRECTION ( 'NONE', ( -0.3444045651374277872, 0.000000000000000000, -0.9388213331153587582 ) ) ; +#52421 = EDGE_CURVE ( 'NONE', #63527, #58647, #20744, .T. ) ; +#52422 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51362, 'distance_accuracy_value', 'NONE'); +#52423 = LINE ( 'NONE', #44718, #40487 ) ; +#52424 = ORIENTED_EDGE ( 'NONE', *, *, #11777, .F. ) ; +#52425 = ORIENTED_EDGE ( 'NONE', *, *, #62740, .F. ) ; +#52426 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52427 = ORIENTED_EDGE ( 'NONE', *, *, #72230, .T. ) ; +#52428 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, -9.880000000000000782, 0.3499999999999999778 ) ) ; +#52429 = FACE_OUTER_BOUND ( 'NONE', #29079, .T. ) ; +#52430 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.8999999999999989120, 0.1829999999999829818 ) ) ; +#52431 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52432 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#52433 = ADVANCED_FACE ( 'NONE', ( #76364 ), #6368, .F. ) ; +#52434 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #66516, #69623 ) ; +#52435 = SURFACE_SIDE_STYLE ('',( #82577 ) ) ; +#52437 = ORIENTED_EDGE ( 'NONE', *, *, #33025, .T. ) ; +#52436 = ORIENTED_EDGE ( 'NONE', *, *, #86872, .F. ) ; +#52438 = STYLED_ITEM ( 'NONE', ( #98660 ), #45604 ) ; +#52439 = EDGE_LOOP ( 'NONE', ( #83455, #36343, #20113, #55223 ) ) ; +#52440 = LINE ( 'NONE', #90730, #70229 ) ; +#52442 = CARTESIAN_POINT ( 'NONE', ( 1.242240128911429986, -0.8869042198941200494, 0.8100000000000000533 ) ) ; +#52441 = CARTESIAN_POINT ( 'NONE', ( 0.4785075026192849856, -0.9340610223455999561, 0.8299999999999999600 ) ) ; +#52443 = FILL_AREA_STYLE_COLOUR ( '', #69063 ) ; +#52444 = FACE_OUTER_BOUND ( 'NONE', #25962, .T. ) ; +#52445 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52446 = VECTOR ( 'NONE', #97024, 1000.000000000000000 ) ; +#52447 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83034 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40891, #88840, #86829 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52448 = CARTESIAN_POINT ( 'NONE', ( -1.367367192634590056, -1.017871276266119951, 0.8299999999999999600 ) ) ; +#52449 = ORIENTED_EDGE ( 'NONE', *, *, #57866, .T. ) ; +#52451 = SURFACE_STYLE_FILL_AREA ( #77417 ) ; +#52450 = FILL_AREA_STYLE ('',( #7895 ) ) ; +#52452 = ORIENTED_EDGE ( 'NONE', *, *, #1464, .F. ) ; +#52453 = ORIENTED_EDGE ( 'NONE', *, *, #70404, .T. ) ; +#52454 = CARTESIAN_POINT ( 'NONE', ( 1.274810379711009967, -1.243129529655299992, 0.8100000000000000533 ) ) ; +#52455 = VECTOR ( 'NONE', #70060, 1000.000000000000000 ) ; +#52456 = EDGE_CURVE ( 'NONE', #13157, #67142, #28785, .T. ) ; +#52457 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#52458 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52460 = STYLED_ITEM ( 'NONE', ( #54960 ), #58758 ) ; +#52461 = EDGE_LOOP ( 'NONE', ( #24975, #26621, #31607, #81850 ) ) ; +#52462 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4169, #87924, #82297, #18973 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52463 = STYLED_ITEM ( 'NONE', ( #73586 ), #8434 ) ; +#52464 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#52465 = DIRECTION ( 'NONE', ( -0.01414952675146630492, -0.9998998904353922912, 0.000000000000000000 ) ) ; +#52466 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#52467 = VERTEX_POINT ( 'NONE', #48287 ) ; +#52469 = SURFACE_STYLE_FILL_AREA ( #74947 ) ; +#52468 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#52470 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52471 = EDGE_LOOP ( 'NONE', ( #90339, #34509, #64137, #34381, #32087, #24615 ) ) ; +#52472 = VERTEX_POINT ( 'NONE', #94181 ) ; +#52473 = EDGE_CURVE ( 'NONE', #31057, #30846, #1287, .T. ) ; +#52474 = FILL_AREA_STYLE_COLOUR ( '', #84803 ) ; +#52475 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56552 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11781, #89502, #3715 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52476 = FACE_OUTER_BOUND ( 'NONE', #57620, .T. ) ; +#52477 = FACE_OUTER_BOUND ( 'NONE', #62725, .T. ) ; +#52478 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76279, #60003, #91109, #75786 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52479 = PLANE ( 'NONE', #49939 ) ; +#52480 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#52481 = PRESENTATION_STYLE_ASSIGNMENT (( #22845 ) ) ; +#52482 = AXIS2_PLACEMENT_3D ( 'NONE', #46714, #17083, #767 ) ; +#52483 = EDGE_LOOP ( 'NONE', ( #88277, #54632, #70505, #13543 ) ) ; +#52484 = CARTESIAN_POINT ( 'NONE', ( 4.414529946168118002, 1.600000000000000089, -11.91553418012614607 ) ) ; +#52485 = VERTEX_POINT ( 'NONE', #272 ) ; +#52486 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72026 ) ) ; +#52487 = PRESENTATION_STYLE_ASSIGNMENT (( #13593 ) ) ; +#52488 = CARTESIAN_POINT ( 'NONE', ( -0.08168056302834829363, -0.9656914468017120390, 0.8100000000000000533 ) ) ; +#52489 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52490 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#52491 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#52492 = PLANE ( 'NONE', #65859 ) ; +#52493 = ORIENTED_EDGE ( 'NONE', *, *, #95870, .F. ) ; +#52494 = PRESENTATION_STYLE_ASSIGNMENT (( #12604 ) ) ; +#52495 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988787, -3.149999999999979927, 0.000000000000000000 ) ) ; +#52496 = CARTESIAN_POINT ( 'NONE', ( 0.3385502766025340060, -0.9005362424757039630, 0.8299999999999999600 ) ) ; +#52497 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66454 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59953, #98625, #4771 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52498 = PRESENTATION_STYLE_ASSIGNMENT (( #74977 ) ) ; +#52499 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52500 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14657, #21862, #52514, #76479 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52501 = CARTESIAN_POINT ( 'NONE', ( 1.874834857517529985, -1.237898259965849901, 0.8100000000000000533 ) ) ; +#52503 = EDGE_CURVE ( 'NONE', #99345, #50477, #69699, .T. ) ; +#52502 = VECTOR ( 'NONE', #79197, 1000.000000000000000 ) ; +#52504 = ADVANCED_FACE ( 'NONE', ( #40613 ), #47246, .T. ) ; +#52505 = FACE_OUTER_BOUND ( 'NONE', #66887, .T. ) ; +#52506 = SURFACE_STYLE_FILL_AREA ( #66320 ) ; +#52507 = SURFACE_STYLE_USAGE ( .BOTH. , #29011 ) ; +#52508 = LINE ( 'NONE', #29013, #6250 ) ; +#52509 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52510 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#52511 = FILL_AREA_STYLE_COLOUR ( '', #90991 ) ; +#52512 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61218, 'distance_accuracy_value', 'NONE'); +#52513 = VERTEX_POINT ( 'NONE', #774 ) ; +#52514 = CARTESIAN_POINT ( 'NONE', ( -0.9833333333333335036, -3.099999999999989875, 0.000000000000000000 ) ) ; +#52515 = LINE ( 'NONE', #83664, #96512 ) ; +#52516 = ADVANCED_FACE ( 'NONE', ( #78394 ), #16575, .F. ) ; +#52517 = ORIENTED_EDGE ( 'NONE', *, *, #34481, .F. ) ; +#52518 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52519 = PRESENTATION_STYLE_ASSIGNMENT (( #37215 ) ) ; +#52520 = ADVANCED_FACE ( 'NONE', ( #26808 ), #48787, .T. ) ; +#52521 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52522 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52523 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66134, 'distance_accuracy_value', 'NONE'); +#52524 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -9.880000000000000782, 0.3499999999999999778 ) ) ; +#52525 = PLANE ( 'NONE', #4030 ) ; +#52526 = STYLED_ITEM ( 'NONE', ( #70845 ), #95989 ) ; +#52527 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#52528 = ORIENTED_EDGE ( 'NONE', *, *, #72804, .F. ) ; +#52529 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52530 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52531 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#52532 = ADVANCED_FACE ( 'NONE', ( #57971 ), #43105, .F. ) ; +#52533 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55711, 'distance_accuracy_value', 'NONE'); +#52534 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#52535 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#52536 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52537 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42371, 'distance_accuracy_value', 'NONE'); +#52538 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52539 = LINE ( 'NONE', #76501, #90909 ) ; +#52540 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52541 = MANIFOLD_SOLID_BREP ( 'ÊäÈë18', #43654 ) ; +#52542 = SURFACE_STYLE_FILL_AREA ( #29056 ) ; +#52543 = ORIENTED_EDGE ( 'NONE', *, *, #43550, .T. ) ; +#52544 = EDGE_CURVE ( 'NONE', #43378, #54341, #79927, .T. ) ; +#52545 = EDGE_LOOP ( 'NONE', ( #8513, #3930, #73235 ) ) ; +#52546 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81756, 'distance_accuracy_value', 'NONE'); +#52547 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52548 = ORIENTED_EDGE ( 'NONE', *, *, #60169, .F. ) ; +#52549 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8648700000000000276 ) ) ; +#52550 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52551 = FILL_AREA_STYLE_COLOUR ( '', #41781 ) ; +#52552 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52553 = PLANE ( 'NONE', #8734 ) ; +#52554 = EDGE_CURVE ( 'NONE', #45383, #3092, #12887, .T. ) ; +#52555 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52556 = SURFACE_STYLE_FILL_AREA ( #66852 ) ; +#52557 = CARTESIAN_POINT ( 'NONE', ( -0.3774237423761729882, -1.003781515188449935, 0.8100000000000010525 ) ) ; +#52558 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#52559 = EDGE_CURVE ( 'NONE', #51946, #13016, #31331, .T. ) ; +#52561 = VERTEX_POINT ( 'NONE', #97684 ) ; +#52560 = VERTEX_POINT ( 'NONE', #51792 ) ; +#52562 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52563 = ORIENTED_EDGE ( 'NONE', *, *, #12720, .T. ) ; +#52564 = CARTESIAN_POINT ( 'NONE', ( 1.531892641499219776, -0.9966931238414048488, 0.8099999999999981659 ) ) ; +#52565 = ADVANCED_FACE ( 'NONE', ( #36962 ), #64487, .T. ) ; +#52566 = CARTESIAN_POINT ( 'NONE', ( -0.7991633060742736605, 1.892060340254192008, 0.8100000000000000533 ) ) ; +#52567 = ORIENTED_EDGE ( 'NONE', *, *, #90334, .T. ) ; +#52568 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64005 ), #55851 ) ; +#52569 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #75948 ) ) ; +#52570 = ORIENTED_EDGE ( 'NONE', *, *, #6046, .F. ) ; +#52571 = STYLED_ITEM ( 'NONE', ( #87525 ), #87752 ) ; +#52572 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#52573 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59087 ) ) ; +#52575 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 8.130910000000000082, 0.8648700000000000276 ) ) ; +#52574 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52576 = LINE ( 'NONE', #28574, #58936 ) ; +#52577 = ORIENTED_EDGE ( 'NONE', *, *, #17341, .F. ) ; +#52578 = FACE_OUTER_BOUND ( 'NONE', #61515, .T. ) ; +#52579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57441 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70377, #31594, #54605 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52580 = ORIENTED_EDGE ( 'NONE', *, *, #81494, .T. ) ; +#52581 = SURFACE_STYLE_USAGE ( .BOTH. , #90360 ) ; +#52582 = EDGE_CURVE ( 'NONE', #75293, #30322, #84415, .T. ) ; +#52583 = SURFACE_STYLE_USAGE ( .BOTH. , #45367 ) ; +#52584 = AXIS2_PLACEMENT_3D ( 'NONE', #100268, #86068, #14071 ) ; +#52585 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23207 ), #11660 ) ; +#52587 = EDGE_LOOP ( 'NONE', ( #14467, #95726, #21089, #28477 ) ) ; +#52586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52588 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#52589 = FILL_AREA_STYLE_COLOUR ( '', #48308 ) ; +#52590 = SURFACE_STYLE_FILL_AREA ( #44383 ) ; +#52591 = STYLED_ITEM ( 'NONE', ( #41334 ), #19122 ) ; +#52592 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#52593 = ORIENTED_EDGE ( 'NONE', *, *, #75232, .T. ) ; +#52594 = CARTESIAN_POINT ( 'NONE', ( 0.006444788832097659778, -1.283680827045200035, 0.8100000000000000533 ) ) ; +#52595 = PRESENTATION_STYLE_ASSIGNMENT (( #99448 ) ) ; +#52596 = ORIENTED_EDGE ( 'NONE', *, *, #41578, .T. ) ; +#52597 = VERTEX_POINT ( 'NONE', #4307 ) ; +#52598 = ADVANCED_FACE ( 'NONE', ( #77762 ), #78766, .T. ) ; +#52599 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#52600 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96578 ) ) ; +#52601 = VECTOR ( 'NONE', #32400, 1000.000000000000000 ) ; +#52602 = VECTOR ( 'NONE', #94122, 1000.000000000000114 ) ; +#52603 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, -8.400000000000000355, -11.41999999999999993 ) ) ; +#52604 = EDGE_CURVE ( 'NONE', #34518, #99420, #100606, .T. ) ; +#52605 = STYLED_ITEM ( 'NONE', ( #83854 ), #60229 ) ; +#52606 = PRESENTATION_STYLE_ASSIGNMENT (( #51110 ) ) ; +#52607 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52608 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96584 ) ) ; +#52609 = SURFACE_STYLE_USAGE ( .BOTH. , #37779 ) ; +#52610 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52611 = AXIS2_PLACEMENT_3D ( 'NONE', #50309, #88072, #2803 ) ; +#52612 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000001305, -3.383333333333326642, 0.000000000000000000 ) ) ; +#52613 = VERTEX_POINT ( 'NONE', #145 ) ; +#52614 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52616 = EDGE_LOOP ( 'NONE', ( #24027, #45119, #58924, #83354 ) ) ; +#52617 = EDGE_CURVE ( 'NONE', #31444, #865, #93037, .T. ) ; +#52618 = VECTOR ( 'NONE', #48059, 1000.000000000000000 ) ; +#52619 = STYLED_ITEM ( 'NONE', ( #43682 ), #9091 ) ; +#52620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52621 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8648700000000000276 ) ) ; +#52622 = PRESENTATION_STYLE_ASSIGNMENT (( #6068 ) ) ; +#52623 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52624 = STYLED_ITEM ( 'NONE', ( #19308 ), #7969 ) ; +#52625 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52626 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52627 = LINE ( 'NONE', #77592, #13297 ) ; +#52628 = SURFACE_STYLE_FILL_AREA ( #81401 ) ; +#52629 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000006162, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#52630 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52631 = SURFACE_SIDE_STYLE ('',( #37798 ) ) ; +#52632 = ADVANCED_FACE ( 'NONE', ( #71112 ), #76752, .T. ) ; +#52633 = EDGE_CURVE ( 'NONE', #71811, #25247, #1156, .T. ) ; +#52635 = FILL_AREA_STYLE_COLOUR ( '', #74673 ) ; +#52634 = CARTESIAN_POINT ( 'NONE', ( -0.5610005133853442905, 2.432921575926969560, 0.8100000000000000533 ) ) ; +#52636 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#52637 = VECTOR ( 'NONE', #30694, 1000.000000000000000 ) ; +#52638 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52639 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11970, 'distance_accuracy_value', 'NONE'); +#52640 = ORIENTED_EDGE ( 'NONE', *, *, #46500, .T. ) ; +#52641 = CARTESIAN_POINT ( 'NONE', ( -1.132903271161860070, -1.445215125000139933, 0.8299999999999999600 ) ) ; +#52642 = PLANE ( 'NONE', #35241 ) ; +#52643 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52644 = ADVANCED_FACE ( 'NONE', ( #63487 ), #55808, .T. ) ; +#52645 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#52646 = FILL_AREA_STYLE ('',( #20990 ) ) ; +#52647 = EDGE_CURVE ( 'NONE', #5636, #27482, #32820, .T. ) ; +#52648 = ORIENTED_EDGE ( 'NONE', *, *, #86410, .F. ) ; +#52649 = STYLED_ITEM ( 'NONE', ( #87130 ), #75804 ) ; +#52650 = VERTEX_POINT ( 'NONE', #63962 ) ; +#52651 = SURFACE_SIDE_STYLE ('',( #7083 ) ) ; +#52652 = FILL_AREA_STYLE ('',( #98508 ) ) ; +#52653 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#52654 = CARTESIAN_POINT ( 'NONE', ( -0.1634999987230950080, -0.9726617844338850682, 0.8299999999999999600 ) ) ; +#52655 = FACE_OUTER_BOUND ( 'NONE', #70113, .T. ) ; +#52656 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52657 = CARTESIAN_POINT ( 'NONE', ( 9.568126999999998716, 10.98066299999999984, 0.8991599999999999593 ) ) ; +#52658 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18590 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13757, #68911, #36810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52659 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#52660 = FILL_AREA_STYLE ('',( #14794 ) ) ; +#52661 = ORIENTED_EDGE ( 'NONE', *, *, #82521, .F. ) ; +#52662 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52663 = LINE ( 'NONE', #20497, #61347 ) ; +#52664 = FACE_OUTER_BOUND ( 'NONE', #24746, .T. ) ; +#52665 = FILL_AREA_STYLE ('',( #43982 ) ) ; +#52666 = ORIENTED_EDGE ( 'NONE', *, *, #5676, .T. ) ; +#52667 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52668 = AXIS2_PLACEMENT_3D ( 'NONE', #53928, #44236, #75394 ) ; +#52669 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24995 ), #21675 ) ; +#52670 = VECTOR ( 'NONE', #2518, 1000.000000000000000 ) ; +#52671 = LINE ( 'NONE', #44961, #94076 ) ; +#52672 = VERTEX_POINT ( 'NONE', #18481 ) ; +#52673 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52675 = STYLED_ITEM ( 'NONE', ( #49029 ), #36808 ) ; +#52676 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#52677 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52678 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#52679 = EDGE_CURVE ( 'NONE', #72386, #31313, #27193, .T. ) ; +#52681 = VERTEX_POINT ( 'NONE', #72127 ) ; +#52680 = ORIENTED_EDGE ( 'NONE', *, *, #79994, .F. ) ; +#52682 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52683 = FILL_AREA_STYLE ('',( #68470 ) ) ; +#52684 = ORIENTED_EDGE ( 'NONE', *, *, #35987, .T. ) ; +#52685 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52686 = CARTESIAN_POINT ( 'NONE', ( -0.4517812530547630212, -1.032254439803430124, 0.8299999999999999600 ) ) ; +#52687 = ORIENTED_EDGE ( 'NONE', *, *, #56842, .F. ) ; +#52688 = ORIENTED_EDGE ( 'NONE', *, *, #90697, .F. ) ; +#52689 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52691 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#52692 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52693 = EDGE_LOOP ( 'NONE', ( #56795, #24718, #11852, #32456 ) ) ; +#52694 = ORIENTED_EDGE ( 'NONE', *, *, #79985, .F. ) ; +#52695 = ORIENTED_EDGE ( 'NONE', *, *, #13345, .F. ) ; +#52696 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#52697 = EDGE_CURVE ( 'NONE', #41304, #71585, #83540, .T. ) ; +#52699 = VERTEX_POINT ( 'NONE', #33841 ) ; +#52698 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52700 = PLANE ( 'NONE', #91398 ) ; +#52701 = PRESENTATION_STYLE_ASSIGNMENT (( #89503 ) ) ; +#52702 = FILL_AREA_STYLE ('',( #68982 ) ) ; +#52703 = SURFACE_STYLE_USAGE ( .BOTH. , #76172 ) ; +#52704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96758 ) ) ; +#52705 = ORIENTED_EDGE ( 'NONE', *, *, #43397, .T. ) ; +#52706 = SURFACE_SIDE_STYLE ('',( #52226 ) ) ; +#52707 = ORIENTED_EDGE ( 'NONE', *, *, #14421, .T. ) ; +#52708 = EDGE_CURVE ( 'NONE', #36035, #65143, #2690, .T. ) ; +#52709 = MANIFOLD_SOLID_BREP ( 'ÊäÈë145', #32097 ) ; +#52710 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52711 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52712 = VECTOR ( 'NONE', #40457, 1000.000000000000114 ) ; +#52713 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8583 ) ) ; +#52715 = ORIENTED_EDGE ( 'NONE', *, *, #29924, .T. ) ; +#52714 = SURFACE_STYLE_USAGE ( .BOTH. , #90501 ) ; +#52716 = SURFACE_STYLE_USAGE ( .BOTH. , #54221 ) ; +#52717 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#52718 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#52719 = CARTESIAN_POINT ( 'NONE', ( -0.9347239525463104659, -1.250624474938026642, 0.8099999999998035438 ) ) ; +#52720 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#52721 = ORIENTED_EDGE ( 'NONE', *, *, #91470, .T. ) ; +#52722 = EDGE_CURVE ( 'NONE', #21864, #43123, #41003, .T. ) ; +#52723 = LINE ( 'NONE', #59915, #98886 ) ; +#52724 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52725 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85730 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28745, #43068, #35451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52726 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80536, #33576, #80038 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52727 = CARTESIAN_POINT ( 'NONE', ( 0.9399999999999999467, -9.880000000000000782, 0.3499999999999999778 ) ) ; +#52728 = EDGE_CURVE ( 'NONE', #96056, #39851, #42001, .T. ) ; +#52729 = CARTESIAN_POINT ( 'NONE', ( 1.688590486522010048, -1.445336647901249938, 0.8100000000000000533 ) ) ; +#52731 = CIRCLE ( 'NONE', #36489, 0.2500000000000001110 ) ; +#52730 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52732 = PLANE ( 'NONE', #9163 ) ; +#52733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42955 ) ) ; +#52734 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34761 ) ) ; +#52735 = PRESENTATION_STYLE_ASSIGNMENT (( #29244 ) ) ; +#52736 = FACE_OUTER_BOUND ( 'NONE', #34870, .T. ) ; +#52737 = ORIENTED_EDGE ( 'NONE', *, *, #46819, .F. ) ; +#52738 = CIRCLE ( 'NONE', #20137, 0.09999999999999939493 ) ; +#52739 = FILL_AREA_STYLE_COLOUR ( '', #46543 ) ; +#52740 = EDGE_CURVE ( 'NONE', #72878, #93165, #73136, .T. ) ; +#52742 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97193 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61714, #12648, #70340 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52741 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52743 = ADVANCED_FACE ( 'NONE', ( #34355 ), #49158, .F. ) ; +#52744 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87001 ), #11901 ) ; +#52745 = FILL_AREA_STYLE_COLOUR ( '', #94030 ) ; +#52746 = ORIENTED_EDGE ( 'NONE', *, *, #55929, .T. ) ; +#52747 = LINE ( 'NONE', #90019, #92759 ) ; +#52749 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52748 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52751 = AXIS2_PLACEMENT_3D ( 'NONE', #59663, #12569, #81111 ) ; +#52750 = CARTESIAN_POINT ( 'NONE', ( 1.680683372326140068, -0.9625852181168450539, 0.8100000000000000533 ) ) ; +#52752 = FILL_AREA_STYLE_COLOUR ( '', #7676 ) ; +#52753 = ADVANCED_FACE ( 'NONE', ( #44956 ), #28665, .T. ) ; +#52754 = VECTOR ( 'NONE', #77333, 1000.000000000000000 ) ; +#52756 = ADVANCED_FACE ( 'NONE', ( #75629 ), #42982, .T. ) ; +#52755 = CARTESIAN_POINT ( 'NONE', ( 6.678958916749879293, 4.142827083250041120, 0.8991599999999999593 ) ) ; +#52757 = STYLED_ITEM ( 'NONE', ( #89256 ), #11476 ) ; +#52758 = FILL_AREA_STYLE ('',( #21587 ) ) ; +#52759 = FILL_AREA_STYLE_COLOUR ( '', #39585 ) ; +#52760 = ORIENTED_EDGE ( 'NONE', *, *, #7577, .T. ) ; +#52761 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52762 = SURFACE_STYLE_USAGE ( .BOTH. , #75716 ) ; +#52763 = PLANE ( 'NONE', #66976 ) ; +#52764 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52765 = SURFACE_STYLE_USAGE ( .BOTH. , #99116 ) ; +#52766 = EDGE_CURVE ( 'NONE', #38877, #100002, #51171, .T. ) ; +#52767 = SURFACE_STYLE_FILL_AREA ( #91542 ) ; +#52768 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52769 = ADVANCED_FACE ( 'NONE', ( #23031, #62343 ), #85288, .F. ) ; +#52770 = PLANE ( 'NONE', #83474 ) ; +#52771 = VERTEX_POINT ( 'NONE', #31680 ) ; +#52772 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#52773 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59224 ), #5417 ) ; +#52774 = VERTEX_POINT ( 'NONE', #46467 ) ; +#52775 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#52776 = SURFACE_SIDE_STYLE ('',( #90566 ) ) ; +#52777 = FILL_AREA_STYLE_COLOUR ( '', #65587 ) ; +#52778 = CARTESIAN_POINT ( 'NONE', ( 7.661837500499949272, 2.155857499500049013, 0.8991599999999999593 ) ) ; +#52779 = AXIS2_PLACEMENT_3D ( 'NONE', #89592, #65594, #95703 ) ; +#52780 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#52781 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.699999999999999734, -3.118622929693471946E-90 ) ) ; +#52782 = ORIENTED_EDGE ( 'NONE', *, *, #93663, .T. ) ; +#52783 = SURFACE_STYLE_FILL_AREA ( #44579 ) ; +#52784 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52785 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39726 ), #571 ) ; +#52786 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#52787 = ORIENTED_EDGE ( 'NONE', *, *, #75660, .F. ) ; +#52788 = PRESENTATION_STYLE_ASSIGNMENT (( #91571 ) ) ; +#52789 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39810 ), #67545 ) ; +#52790 = VECTOR ( 'NONE', #44469, 1000.000000000000114 ) ; +#52791 = SURFACE_STYLE_USAGE ( .BOTH. , #52303 ) ; +#52792 = SURFACE_SIDE_STYLE ('',( #21637 ) ) ; +#52793 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#52794 = STYLED_ITEM ( 'NONE', ( #31746 ), #76312 ) ; +#52795 = FILL_AREA_STYLE ('',( #21639 ) ) ; +#52796 = FACE_OUTER_BOUND ( 'NONE', #56227, .T. ) ; +#52797 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#52798 = EDGE_CURVE ( 'NONE', #10139, #39524, #32198, .T. ) ; +#52799 = EDGE_LOOP ( 'NONE', ( #81974, #61354, #76639, #33611 ) ) ; +#52800 = SURFACE_STYLE_FILL_AREA ( #13924 ) ; +#52801 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 8.286473000000000866, 0.8991599999999999593 ) ) ; +#52802 = AXIS2_PLACEMENT_3D ( 'NONE', #39817, #70959, #31149 ) ; +#52803 = EDGE_CURVE ( 'NONE', #27995, #25062, #77129, .T. ) ; +#52804 = VECTOR ( 'NONE', #52386, 1000.000000000000000 ) ; +#52805 = VERTEX_POINT ( 'NONE', #22002 ) ; +#52806 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52807 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#52808 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#52809 = SURFACE_STYLE_FILL_AREA ( #52320 ) ; +#52810 = ORIENTED_EDGE ( 'NONE', *, *, #47326, .F. ) ; +#52811 = VECTOR ( 'NONE', #100680, 1000.000000000000000 ) ; +#52812 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52813 = AXIS2_PLACEMENT_3D ( 'NONE', #30271, #61477, #92559 ) ; +#52814 = ADVANCED_FACE ( 'NONE', ( #69443 ), #30645, .F. ) ; +#52815 = ORIENTED_EDGE ( 'NONE', *, *, #47589, .T. ) ; +#52817 = EDGE_LOOP ( 'NONE', ( #84926, #53548, #71788, #100783 ) ) ; +#52816 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#52818 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1602, 'distance_accuracy_value', 'NONE'); +#52819 = VECTOR ( 'NONE', #62524, 1000.000000000000000 ) ; +#52820 = SURFACE_STYLE_FILL_AREA ( #13954 ) ; +#52822 = CARTESIAN_POINT ( 'NONE', ( -1.364612412596039936, -1.414598001867640065, 0.8100000000000000533 ) ) ; +#52821 = LINE ( 'NONE', #77800, #75407 ) ; +#52823 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.5000000000000019984, 0.1829999999999659954 ) ) ; +#52824 = VERTEX_POINT ( 'NONE', #78636 ) ; +#52825 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#52826 = ORIENTED_EDGE ( 'NONE', *, *, #65855, .F. ) ; +#52827 = ADVANCED_FACE ( 'NONE', ( #77640 ), #30146, .T. ) ; +#52828 = CARTESIAN_POINT ( 'NONE', ( 0.4933785085725994612, 0.5074992478988522571, 0.8100000000000000533 ) ) ; +#52829 = SURFACE_STYLE_USAGE ( .BOTH. , #69088 ) ; +#52830 = PRESENTATION_STYLE_ASSIGNMENT (( #91122 ) ) ; +#52831 = FILL_AREA_STYLE ('',( #91610 ) ) ; +#52832 = CIRCLE ( 'NONE', #11994, 0.1200000000000000927 ) ; +#52833 = ORIENTED_EDGE ( 'NONE', *, *, #5114, .F. ) ; +#52834 = ORIENTED_EDGE ( 'NONE', *, *, #18438, .F. ) ; +#52835 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92304 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63642, #24851, #49311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52837 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52836 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#52838 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#52839 = SURFACE_STYLE_USAGE ( .BOTH. , #59031 ) ; +#52840 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39792 ), #70756 ) ; +#52841 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52842 = ORIENTED_EDGE ( 'NONE', *, *, #40744, .F. ) ; +#52843 = CARTESIAN_POINT ( 'NONE', ( 1.238543046823479932, -1.444732071753930036, 0.8100000000000000533 ) ) ; +#52844 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41420 ), #5567 ) ; +#52845 = ORIENTED_EDGE ( 'NONE', *, *, #82957, .T. ) ; +#52846 = LINE ( 'NONE', #83987, #71544 ) ; +#52848 = SURFACE_STYLE_USAGE ( .BOTH. , #75817 ) ; +#52847 = PLANE ( 'NONE', #18367 ) ; +#52849 = VECTOR ( 'NONE', #57171, 1000.000000000000000 ) ; +#52850 = STYLED_ITEM ( 'NONE', ( #85637 ), #88577 ) ; +#52851 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52852 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52854 = VECTOR ( 'NONE', #92053, 1000.000000000000000 ) ; +#52853 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#52855 = STYLED_ITEM ( 'NONE', ( #53054 ), #26528 ) ; +#52856 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8648700000000000276 ) ) ; +#52857 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52858 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52859 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52860 = SURFACE_SIDE_STYLE ('',( #12967 ) ) ; +#52861 = EDGE_LOOP ( 'NONE', ( #14403, #85190, #70584, #15334 ) ) ; +#52862 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#52863 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52864 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52867 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#52866 = FILL_AREA_STYLE ('',( #99701 ) ) ; +#52865 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52868 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64836, 'distance_accuracy_value', 'NONE'); +#52869 = LINE ( 'NONE', #22719, #81128 ) ; +#52871 = ADVANCED_FACE ( 'NONE', ( #56712 ), #64842, .T. ) ; +#52870 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#52872 = VECTOR ( 'NONE', #96020, 1000.000000000000000 ) ; +#52873 = AXIS2_PLACEMENT_3D ( 'NONE', #7456, #16669, #47866 ) ; +#52874 = FACE_OUTER_BOUND ( 'NONE', #73717, .T. ) ; +#52875 = FILL_AREA_STYLE ('',( #44671 ) ) ; +#52876 = AXIS2_PLACEMENT_3D ( 'NONE', #72221, #8327, #93640 ) ; +#52877 = FACE_OUTER_BOUND ( 'NONE', #38366, .T. ) ; +#52878 = FILL_AREA_STYLE_COLOUR ( '', #31505 ) ; +#52879 = EDGE_LOOP ( 'NONE', ( #14107, #78667, #84586, #72006 ) ) ; +#52881 = MANIFOLD_SOLID_BREP ( 'ÊäÈë77', #41951 ) ; +#52880 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.000000000000000000 ) ) ; +#52882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52883 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.399999999999999911, -13.35000000000000142 ) ) ; +#52886 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32402 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65532, #89042, #66058 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52885 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#52884 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#52887 = CARTESIAN_POINT ( 'NONE', ( 0.009882622001633050227, -1.368793146596559929, 0.8100000000000000533 ) ) ; +#52888 = EDGE_CURVE ( 'NONE', #42036, #44849, #72488, .T. ) ; +#52889 = VECTOR ( 'NONE', #67043, 1000.000000000000000 ) ; +#52890 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52891 = SURFACE_STYLE_USAGE ( .BOTH. , #22737 ) ; +#52892 = LINE ( 'NONE', #76339, #27848 ) ; +#52893 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52895 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#52894 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75757 ), #28465 ) ; +#52896 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#52897 = EDGE_CURVE ( 'NONE', #10911, #32731, #79158, .T. ) ; +#52898 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52899 = SURFACE_STYLE_FILL_AREA ( #99250 ) ; +#52900 = FILL_AREA_STYLE ('',( #60566 ) ) ; +#52901 = VECTOR ( 'NONE', #25636, 1000.000000000000000 ) ; +#52902 = FACE_OUTER_BOUND ( 'NONE', #29119, .T. ) ; +#52903 = SURFACE_STYLE_FILL_AREA ( #14021 ) ; +#52904 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52905 = SURFACE_STYLE_USAGE ( .BOTH. , #82041 ) ; +#52906 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#52907 = CARTESIAN_POINT ( 'NONE', ( 1.296446609406725958, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#52908 = AXIS2_PLACEMENT_3D ( 'NONE', #62398, #47048, #68513 ) ; +#52909 = LINE ( 'NONE', #92653, #34071 ) ; +#52910 = FACE_OUTER_BOUND ( 'NONE', #23135, .T. ) ; +#52911 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#52912 = FILL_AREA_STYLE ('',( #68684 ) ) ; +#52913 = ORIENTED_EDGE ( 'NONE', *, *, #69784, .F. ) ; +#52914 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#52915 = PLANE ( 'NONE', #7756 ) ; +#52916 = FILL_AREA_STYLE ('',( #44705 ) ) ; +#52917 = LINE ( 'NONE', #4411, #81315 ) ; +#52918 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#52919 = VECTOR ( 'NONE', #83471, 1000.000000000000000 ) ; +#52920 = LINE ( 'NONE', #85036, #41879 ) ; +#52921 = LINE ( 'NONE', #74886, #40723 ) ; +#52922 = SURFACE_SIDE_STYLE ('',( #5884 ) ) ; +#52923 = ORIENTED_EDGE ( 'NONE', *, *, #46964, .T. ) ; +#52924 = SURFACE_STYLE_FILL_AREA ( #94194 ) ; +#52925 = CARTESIAN_POINT ( 'NONE', ( -0.02315300183346909874, -1.415447185383410078, 0.8300000000000006262 ) ) ; +#52926 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20319 ) ) ; +#52927 = VECTOR ( 'NONE', #15386, 1000.000000000000000 ) ; +#52928 = EDGE_CURVE ( 'NONE', #65830, #8318, #34233, .T. ) ; +#52929 = LINE ( 'NONE', #43731, #60029 ) ; +#52930 = VERTEX_POINT ( 'NONE', #56198 ) ; +#52931 = ORIENTED_EDGE ( 'NONE', *, *, #90624, .T. ) ; +#52932 = VECTOR ( 'NONE', #90986, 1000.000000000000000 ) ; +#52933 = VECTOR ( 'NONE', #73357, 1000.000000000000000 ) ; +#52934 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52935 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#52936 = EDGE_LOOP ( 'NONE', ( #50587, #98783, #44939, #77792 ) ) ; +#52937 = PLANE ( 'NONE', #80369 ) ; +#52938 = CARTESIAN_POINT ( 'NONE', ( 0.002442604188005680164, -1.482878949593630091, 0.8100000000000000533 ) ) ; +#52939 = CARTESIAN_POINT ( 'NONE', ( 0.4675224071360329914, -1.231957836876500068, 0.8299999999999999600 ) ) ; +#52940 = VECTOR ( 'NONE', #58845, 1000.000000000000000 ) ; +#52941 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#52942 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#52943 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #74905, #15067 ), + ( #23295, #13536 ), + ( #76389, #60606 ), + ( #85056, #84069 ), + ( #7375, #52939 ), + ( #6389, #69725 ), + ( #21771, #37116 ), + ( #15593, #14064 ), + ( #37618, #83571 ), + ( #76905, #45221 ), + ( #61104, #44726 ), + ( #75895, #54451 ), + ( #14569, #85559 ), + ( #68709, #46219 ), + ( #5899, #22785 ), + ( #68217, #99760 ), + ( #29921, #22274 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.1243326568241810010, 0.2472115806153259987, 0.3081045382937199761, 0.3686632993063180264, 0.4278342660164959899, 0.4874377344565560266, 0.5471209518679810424, 0.6069315464593240117, 0.6674064697376600463, 0.7287490833101170074, 0.7918515905586700487, 0.8577802721522059803, 0.9268425776014700412, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52944 = SURFACE_SIDE_STYLE ('',( #92213 ) ) ; +#52945 = ORIENTED_EDGE ( 'NONE', *, *, #20072, .T. ) ; +#52946 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96925 ) ) ; +#52947 = ORIENTED_EDGE ( 'NONE', *, *, #64398, .T. ) ; +#52948 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#52949 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8099999999999827338 ) ) ; +#52950 = VECTOR ( 'NONE', #34181, 1000.000000000000000 ) ; +#52951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10443, 'distance_accuracy_value', 'NONE'); +#52952 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#52954 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#52953 = SURFACE_SIDE_STYLE ('',( #93691 ) ) ; +#52955 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52956 = VECTOR ( 'NONE', #60938, 1000.000000000000000 ) ; +#52957 = EDGE_CURVE ( 'NONE', #74469, #59650, #87312, .T. ) ; +#52958 = PRESENTATION_STYLE_ASSIGNMENT (( #62635 ) ) ; +#52959 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#52961 = AXIS2_PLACEMENT_3D ( 'NONE', #24994, #16761, #62271 ) ; +#52960 = VECTOR ( 'NONE', #9897, 1000.000000000000000 ) ; +#52962 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77583, #55644, #30582, #78578, #70409, #93365, #92853, #61789, #63312 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999967804, 0.3749999999999966138, 0.4999999999999964473, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#52963 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61126 ) ) ; +#52964 = CARTESIAN_POINT ( 'NONE', ( -1.353802252918679949, -0.9813977598329840513, 0.8100000000000000533 ) ) ; +#52965 = ORIENTED_EDGE ( 'NONE', *, *, #56118, .T. ) ; +#52966 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#52967 = ORIENTED_EDGE ( 'NONE', *, *, #67217, .F. ) ; +#52968 = VERTEX_POINT ( 'NONE', #18857 ) ; +#52969 = CARTESIAN_POINT ( 'NONE', ( 1.006730632090929944, -1.141526082476280068, 0.8100000000000000533 ) ) ; +#52970 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61811 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34244, #64352, #96466 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#52972 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#52971 = FILL_AREA_STYLE ('',( #82600 ) ) ; +#52973 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#52974 = SURFACE_STYLE_FILL_AREA ( #22299 ) ; +#52976 = ORIENTED_EDGE ( 'NONE', *, *, #10763, .F. ) ; +#52975 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#52977 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#52978 = VECTOR ( 'NONE', #81258, 1000.000000000000000 ) ; +#52979 = FACE_OUTER_BOUND ( 'NONE', #53468, .T. ) ; +#52980 = FACE_OUTER_BOUND ( 'NONE', #87175, .T. ) ; +#52981 = ORIENTED_EDGE ( 'NONE', *, *, #37539, .F. ) ; +#52983 = PLANE ( 'NONE', #22469 ) ; +#52982 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8199999999999999512 ) ) ; +#52984 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, -3.500000000000000444, 0.000000000000000000 ) ) ; +#52985 = ORIENTED_EDGE ( 'NONE', *, *, #100099, .F. ) ; +#52986 = ORIENTED_EDGE ( 'NONE', *, *, #17993, .F. ) ; +#52987 = EDGE_CURVE ( 'NONE', #20920, #70649, #26631, .T. ) ; +#52988 = PRESENTATION_STYLE_ASSIGNMENT (( #21818 ) ) ; +#52989 = CARTESIAN_POINT ( 'NONE', ( -1.267164372650494197, -0.9871347208242026161, 0.8099999999999977218 ) ) ; +#52990 = STYLED_ITEM ( 'NONE', ( #39505 ), #72445 ) ; +#52991 = FILL_AREA_STYLE ('',( #45271 ) ) ; +#52992 = PLANE ( 'NONE', #94772 ) ; +#52993 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#52994 = VERTEX_POINT ( 'NONE', #72009 ) ; +#52995 = PRESENTATION_STYLE_ASSIGNMENT (( #91270 ) ) ; +#52996 = ORIENTED_EDGE ( 'NONE', *, *, #86523, .T. ) ; +#52997 = FACE_OUTER_BOUND ( 'NONE', #51491, .T. ) ; +#52998 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#52999 = CARTESIAN_POINT ( 'NONE', ( 1.075908802260020058, -1.102553831183370026, 0.8299999999999999600 ) ) ; +#53000 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000007688, -3.149999999999979927, 0.000000000000000000 ) ) ; +#53001 = VECTOR ( 'NONE', #21445, 1000.000000000000000 ) ; +#53002 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#53003 = ORIENTED_EDGE ( 'NONE', *, *, #23680, .F. ) ; +#53004 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#53006 = FACE_BOUND ( 'NONE', #49381, .T. ) ; +#53005 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30084 ), #2495 ) ; +#53007 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#53008 = SURFACE_STYLE_FILL_AREA ( #37192 ) ; +#53009 = LINE ( 'NONE', #38184, #8187 ) ; +#53010 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53011 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10346 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50051, #92311, #31048 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53012 = SURFACE_STYLE_FILL_AREA ( #54000 ) ; +#53013 = SURFACE_STYLE_FILL_AREA ( #99361 ) ; +#53014 = ADVANCED_FACE ( 'NONE', ( #2062 ), #87821, .T. ) ; +#53015 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53016 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53017 = SURFACE_STYLE_USAGE ( .BOTH. , #60678 ) ; +#53018 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#53019 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35676 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92892, #54143, #32181 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53020 = LINE ( 'NONE', #90812, #19189 ) ; +#53021 = FACE_OUTER_BOUND ( 'NONE', #18562, .T. ) ; +#53022 = LINE ( 'NONE', #84152, #8399 ) ; +#53023 = EDGE_LOOP ( 'NONE', ( #40008, #42333, #1319, #100904 ) ) ; +#53024 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#53025 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#53027 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53026 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26942 ) ) ; +#53028 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6587 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77339, #7324, #9347 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53029 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#53030 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53031 = LINE ( 'NONE', #75011, #17057 ) ; +#53032 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#53033 = AXIS2_PLACEMENT_3D ( 'NONE', #97156, #41573, #3260 ) ; +#53034 = CARTESIAN_POINT ( 'NONE', ( 10.70135999999999932, 12.60947499999999977, 0.8991599999999999593 ) ) ; +#53035 = EDGE_CURVE ( 'NONE', #8138, #29476, #8005, .T. ) ; +#53036 = ORIENTED_EDGE ( 'NONE', *, *, #25856, .F. ) ; +#53037 = STYLED_ITEM ( 'NONE', ( #58516 ), #3469 ) ; +#53038 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#53039 = SURFACE_STYLE_USAGE ( .BOTH. , #98898 ) ; +#53040 = AXIS2_PLACEMENT_3D ( 'NONE', #56353, #7730, #15966 ) ; +#53041 = SURFACE_STYLE_FILL_AREA ( #36221 ) ; +#53042 = ADVANCED_FACE ( 'NONE', ( #12140 ), #74924, .T. ) ; +#53043 = MANIFOLD_SOLID_BREP ( 'ÊäÈë43', #50205 ) ; +#53044 = LINE ( 'NONE', #14683, #37978 ) ; +#53045 = VERTEX_POINT ( 'NONE', #22910 ) ; +#53046 = VERTEX_POINT ( 'NONE', #95199 ) ; +#53047 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53048 = ORIENTED_EDGE ( 'NONE', *, *, #15272, .T. ) ; +#53049 = FILL_AREA_STYLE_COLOUR ( '', #10132 ) ; +#53050 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39999 ), #17093 ) ; +#53051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53052 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#53053 = DIRECTION ( 'NONE', ( -1.853357274465659969E-67, 1.000000000000000000, -4.266452400824600274E-34 ) ) ; +#53054 = PRESENTATION_STYLE_ASSIGNMENT (( #90848 ) ) ; +#53055 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #3873 ) ; +#53056 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53057 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999580573 ) ) ; +#53059 = VERTEX_POINT ( 'NONE', #38219 ) ; +#53058 = ORIENTED_EDGE ( 'NONE', *, *, #10909, .F. ) ; +#53060 = EDGE_LOOP ( 'NONE', ( #4915, #100776, #71034, #39392 ) ) ; +#53061 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67678 ) ) ; +#53062 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56319, 'distance_accuracy_value', 'NONE'); +#53063 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53065 = CARTESIAN_POINT ( 'NONE', ( 0.5096387987012981347, 0.7099999999999999645, -6.437450399132682577E-17 ) ) ; +#53064 = PLANE ( 'NONE', #78302 ) ; +#53066 = ORIENTED_EDGE ( 'NONE', *, *, #1974, .F. ) ; +#53068 = ORIENTED_EDGE ( 'NONE', *, *, #12788, .T. ) ; +#53067 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43090 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19130, #11899, #74285 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53069 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53070 = SURFACE_STYLE_FILL_AREA ( #7002 ) ; +#53071 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29791 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24146, #39423, #71087 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53072 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998730, -0.1400000000000000688 ) ) ; +#53073 = FILL_AREA_STYLE ('',( #76532 ) ) ; +#53074 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4750000000000000333, -0.2458578643762690530 ) ) ; +#53075 = ORIENTED_EDGE ( 'NONE', *, *, #19902, .T. ) ; +#53076 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55324 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63021, #93578, #25721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53077 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97054 ), #30154 ) ; +#53078 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, -0.2500000000000000000 ) ) ; +#53079 = ORIENTED_EDGE ( 'NONE', *, *, #89424, .T. ) ; +#53080 = EDGE_CURVE ( 'NONE', #30288, #89742, #13139, .T. ) ; +#53081 = EDGE_LOOP ( 'NONE', ( #25858, #53840, #57991, #86454 ) ) ; +#53082 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#53083 = VECTOR ( 'NONE', #1065, 1000.000000000000000 ) ; +#53084 = PRESENTATION_STYLE_ASSIGNMENT (( #13694 ) ) ; +#53085 = PLANE ( 'NONE', #88022 ) ; +#53087 = ORIENTED_EDGE ( 'NONE', *, *, #73393, .T. ) ; +#53086 = SURFACE_SIDE_STYLE ('',( #61269 ) ) ; +#53088 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53089 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53090 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53091 = ORIENTED_EDGE ( 'NONE', *, *, #44484, .F. ) ; +#53093 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53092 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53094 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -4.266452400824600274E-34 ) ) ; +#53095 = ORIENTED_EDGE ( 'NONE', *, *, #88158, .F. ) ; +#53096 = ORIENTED_EDGE ( 'NONE', *, *, #55112, .T. ) ; +#53097 = EDGE_CURVE ( 'NONE', #30261, #22415, #23335, .T. ) ; +#53098 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.7000000000000000666, -0.02000000000001045039 ) ) ; +#53099 = EDGE_CURVE ( 'NONE', #839, #72146, #25321, .T. ) ; +#53100 = VECTOR ( 'NONE', #16385, 1000.000000000000000 ) ; +#53101 = FILL_AREA_STYLE ('',( #90890 ) ) ; +#53102 = VECTOR ( 'NONE', #28755, 1000.000000000000000 ) ; +#53103 = VECTOR ( 'NONE', #19943, 1000.000000000000000 ) ; +#53104 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18826 ), #22108 ) ; +#53105 = CARTESIAN_POINT ( 'NONE', ( 1.172627409212990024, -1.219266740403220028, 0.8299999999999997380 ) ) ; +#53106 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#53107 = EDGE_LOOP ( 'NONE', ( #85758, #97824, #331, #43069 ) ) ; +#53108 = CARTESIAN_POINT ( 'NONE', ( 0.4579875826041610032, -1.125997481646370035, 0.8299999999999999600 ) ) ; +#53109 = SURFACE_SIDE_STYLE ('',( #66902 ) ) ; +#53110 = EDGE_LOOP ( 'NONE', ( #23918, #92847, #75078, #64752, #75785, #19744 ) ) ; +#53111 = VECTOR ( 'NONE', #82347, 1000.000000000000114 ) ; +#53112 = FILL_AREA_STYLE ('',( #20441 ) ) ; +#53113 = CYLINDRICAL_SURFACE ( 'NONE', #82640, 0.3000000000000000444 ) ; +#53115 = EDGE_CURVE ( 'NONE', #71812, #72845, #53044, .T. ) ; +#53114 = LINE ( 'NONE', #7046, #80811 ) ; +#53117 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.188311688311689984, 0.8099999999999716316 ) ) ; +#53116 = CARTESIAN_POINT ( 'NONE', ( -0.07759375636085262540, -1.444683470624803512, 0.8099999999995817213 ) ) ; +#53118 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#53119 = FILL_AREA_STYLE_COLOUR ( '', #37019 ) ; +#53120 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23693, #93081, #24219, #77290 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53121 = PRESENTATION_STYLE_ASSIGNMENT (( #21956 ) ) ; +#53122 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53123 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 9.700687000000002058, 0.8648700000000000276 ) ) ; +#53124 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#53125 = SURFACE_SIDE_STYLE ('',( #22987 ) ) ; +#53126 = FILL_AREA_STYLE_COLOUR ( '', #62018 ) ; +#53127 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71870 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81124, #88266, #42801 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53128 = ADVANCED_FACE ( 'NONE', ( #30510 ), #84176, .T. ) ; +#53129 = VECTOR ( 'NONE', #41929, 1000.000000000000000 ) ; +#53130 = EDGE_CURVE ( 'NONE', #83102, #38590, #55956, .T. ) ; +#53131 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#53132 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53133 = SURFACE_STYLE_FILL_AREA ( #59320 ) ; +#53134 = VECTOR ( 'NONE', #58219, 1000.000000000000114 ) ; +#53135 = ORIENTED_EDGE ( 'NONE', *, *, #22772, .F. ) ; +#53136 = CARTESIAN_POINT ( 'NONE', ( -1.092088612093490063, -1.441583773770549914, 0.8100000000000000533 ) ) ; +#53137 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63595, 'distance_accuracy_value', 'NONE'); +#53138 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37306, 'distance_accuracy_value', 'NONE'); +#53139 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53140 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53141 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, -3.099999999999969891, 0.000000000000000000 ) ) ; +#53142 = FILL_AREA_STYLE ('',( #77111 ) ) ; +#53143 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.616666666666666252, 0.000000000000000000 ) ) ; +#53144 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53145 = PRODUCT ( 'uid__2482', 'uid__2482', '', ( #56082 ) ) ; +#53146 = PRESENTATION_STYLE_ASSIGNMENT (( #6600 ) ) ; +#53147 = EDGE_CURVE ( 'NONE', #54195, #8666, #40627, .T. ) ; +#53148 = AXIS2_PLACEMENT_3D ( 'NONE', #22932, #22407, #77533 ) ; +#53149 = ORIENTED_EDGE ( 'NONE', *, *, #37689, .F. ) ; +#53150 = ORIENTED_EDGE ( 'NONE', *, *, #66666, .F. ) ; +#53151 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52784, 'distance_accuracy_value', 'NONE'); +#53152 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47485, 'distance_accuracy_value', 'NONE'); +#53153 = SURFACE_SIDE_STYLE ('',( #67445 ) ) ; +#53154 = SURFACE_SIDE_STYLE ('',( #31670 ) ) ; +#53155 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#53156 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#53157 = SURFACE_STYLE_FILL_AREA ( #91447 ) ; +#53158 = STYLED_ITEM ( 'NONE', ( #78627 ), #15692 ) ; +#53159 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53160 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53161 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53162 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53163 = EDGE_LOOP ( 'NONE', ( #25365, #62875, #93018, #10195 ) ) ; +#53164 = EDGE_CURVE ( 'NONE', #828, #84594, #76503, .T. ) ; +#53165 = LINE ( 'NONE', #91455, #87333 ) ; +#53167 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92276 ) ) ; +#53166 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.600000000000000089, -11.57000000000000028 ) ) ; +#53168 = ORIENTED_EDGE ( 'NONE', *, *, #39778, .F. ) ; +#53169 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#53170 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20856 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35343, #75122, #51144 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53171 = ORIENTED_EDGE ( 'NONE', *, *, #27893, .T. ) ; +#53172 = ADVANCED_FACE ( 'NONE', ( #64103 ), #99873, .T. ) ; +#53173 = VECTOR ( 'NONE', #94927, 1000.000000000000000 ) ; +#53174 = LINE ( 'NONE', #21018, #71288 ) ; +#53175 = LINE ( 'NONE', #82806, #73996 ) ; +#53176 = CARTESIAN_POINT ( 'NONE', ( 1.872286628785889917, -1.103202958186300320, 0.8299999999999999600 ) ) ; +#53177 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53178 = ADVANCED_FACE ( 'NONE', ( #88574 ), #33169, .T. ) ; +#53180 = EDGE_LOOP ( 'NONE', ( #41896, #1182, #10131, #8269 ) ) ; +#53179 = VERTEX_POINT ( 'NONE', #18620 ) ; +#53181 = VECTOR ( 'NONE', #61640, 1000.000000000000000 ) ; +#53182 = ORIENTED_EDGE ( 'NONE', *, *, #28989, .F. ) ; +#53183 = STYLED_ITEM ( 'NONE', ( #17234 ), #12833 ) ; +#53184 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#53185 = FILL_AREA_STYLE_COLOUR ( '', #58887 ) ; +#53186 = ORIENTED_EDGE ( 'NONE', *, *, #58231, .T. ) ; +#53187 = EDGE_LOOP ( 'NONE', ( #14725, #54570, #99800, #5406, #91604, #9717, #69450, #56124, #48158, #68272, #29384, #92996, #63144, #87860, #27966, #3185, #10265, #77810, #51286, #49261, #65724, #82225, #38549, #16466, #48371, #38469, #34382, #17261, #15847, #51208, #63015, #90364, #72176, #46349, #23811, #6377, #90017, #87489, #18233, #90268, #82741, #48098, #87852, #72288, #24635, #14264, #68953, #21801, #43009, #9873, #65125, #21148, #91753, #57217, #89631, #23062, #70164, #7835, #5905, #9548 ) ) ; +#53188 = FILL_AREA_STYLE ('',( #61864 ) ) ; +#53189 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53190 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#53191 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#53192 = SURFACE_STYLE_FILL_AREA ( #22033 ) ; +#53193 = ORIENTED_EDGE ( 'NONE', *, *, #22424, .T. ) ; +#53195 = ORIENTED_EDGE ( 'NONE', *, *, #41024, .F. ) ; +#53194 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17710 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61154, #5941, #45759 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53196 = ORIENTED_EDGE ( 'NONE', *, *, #36305, .T. ) ; +#53197 = ADVANCED_FACE ( 'NONE', ( #34493 ), #20122, .T. ) ; +#53198 = LINE ( 'NONE', #36376, #62349 ) ; +#53199 = AXIS2_PLACEMENT_3D ( 'NONE', #81392, #17158, #43542 ) ; +#53201 = VERTEX_POINT ( 'NONE', #59988 ) ; +#53200 = LINE ( 'NONE', #46512, #41250 ) ; +#53202 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53203 = SURFACE_SIDE_STYLE ('',( #70005 ) ) ; +#53205 = LINE ( 'NONE', #98559, #72541 ) ; +#53204 = AXIS2_PLACEMENT_3D ( 'NONE', #44422, #14255, #98487 ) ; +#53206 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53207 = VERTEX_POINT ( 'NONE', #76765 ) ; +#53208 = LINE ( 'NONE', #91988, #3585 ) ; +#53209 = ORIENTED_EDGE ( 'NONE', *, *, #8189, .F. ) ; +#53210 = MANIFOLD_SOLID_BREP ( 'ÊäÈë175', #69813 ) ; +#53211 = EDGE_CURVE ( 'NONE', #61263, #82578, #43606, .T. ) ; +#53212 = VECTOR ( 'NONE', #92499, 1000.000000000000000 ) ; +#53213 = VECTOR ( 'NONE', #87994, 1000.000000000000000 ) ; +#53214 = ADVANCED_FACE ( 'NONE', ( #4804 ), #44595, .T. ) ; +#53215 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53216 = AXIS2_PLACEMENT_3D ( 'NONE', #83198, #50565, #43869 ) ; +#53217 = ADVANCED_FACE ( 'NONE', ( #91092 ), #100139, .T. ) ; +#53219 = ORIENTED_EDGE ( 'NONE', *, *, #92862, .F. ) ; +#53218 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53220 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53221 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53222 = FILL_AREA_STYLE ('',( #92000 ) ) ; +#53223 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53224 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22234 ), #17120 ) ; +#53225 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#53226 = AXIS2_PLACEMENT_3D ( 'NONE', #96908, #32659, #81143 ) ; +#53227 = FILL_AREA_STYLE ('',( #68515 ) ) ; +#53228 = ORIENTED_EDGE ( 'NONE', *, *, #1548, .T. ) ; +#53229 = FACE_OUTER_BOUND ( 'NONE', #98471, .T. ) ; +#53230 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#53231 = EDGE_CURVE ( 'NONE', #5892, #80014, #46087, .T. ) ; +#53232 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23426, #14709, #45854, #94349 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53233 = SURFACE_SIDE_STYLE ('',( #22576 ) ) ; +#53235 = CARTESIAN_POINT ( 'NONE', ( 1.617712736099780280, -1.425091422160009946, 0.8299999999999999600 ) ) ; +#53234 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#53236 = CARTESIAN_POINT ( 'NONE', ( 10.08014250050017324, 4.574162500500176698, 0.8991599999999999593 ) ) ; +#53237 = EDGE_CURVE ( 'NONE', #96473, #80595, #13547, .T. ) ; +#53238 = VECTOR ( 'NONE', #27817, 1000.000000000000000 ) ; +#53239 = FACE_OUTER_BOUND ( 'NONE', #28213, .T. ) ; +#53240 = ORIENTED_EDGE ( 'NONE', *, *, #87085, .T. ) ; +#53241 = VECTOR ( 'NONE', #82181, 1000.000000000000000 ) ; +#53242 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53243 = AXIS2_PLACEMENT_3D ( 'NONE', #5808, #29333, #44626 ) ; +#53244 = ORIENTED_EDGE ( 'NONE', *, *, #45728, .F. ) ; +#53245 = ADVANCED_FACE ( 'NONE', ( #7735 ), #70101, .F. ) ; +#53246 = ADVANCED_FACE ( 'NONE', ( #94057 ), #78297, .T. ) ; +#53248 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#53247 = DIRECTION ( 'NONE', ( -1.668003342285390072E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53249 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.100000000000000089, 2.617092726158356351E-79 ) ) ; +#53250 = AXIS2_PLACEMENT_3D ( 'NONE', #12939, #83481, #38022 ) ; +#53251 = SURFACE_STYLE_FILL_AREA ( #35936 ) ; +#53252 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999972453, 0.3800000000146488977, 0.6999285677985320753 ) ) ; +#53253 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53254 = ORIENTED_EDGE ( 'NONE', *, *, #74185, .T. ) ; +#53255 = FILL_AREA_STYLE ('',( #13879 ) ) ; +#53256 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53257 = SURFACE_STYLE_USAGE ( .BOTH. , #61438 ) ; +#53258 = SURFACE_STYLE_FILL_AREA ( #5739 ) ; +#53259 = CYLINDRICAL_SURFACE ( 'NONE', #40042, 0.05000000000000012768 ) ; +#53260 = STYLED_ITEM ( 'NONE', ( #57791 ), #73722 ) ; +#53261 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53262 = FILL_AREA_STYLE_COLOUR ( '', #60740 ) ; +#53263 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96776, 'distance_accuracy_value', 'NONE'); +#53264 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53265 = VECTOR ( 'NONE', #90515, 999.9999999999998863 ) ; +#53266 = EDGE_CURVE ( 'NONE', #29809, #15490, #8254, .T. ) ; +#53267 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53268 = ORIENTED_EDGE ( 'NONE', *, *, #31087, .F. ) ; +#53269 = FILL_AREA_STYLE_COLOUR ( '', #4102 ) ; +#53270 = ORIENTED_EDGE ( 'NONE', *, *, #14074, .F. ) ; +#53271 = LINE ( 'NONE', #99134, #61713 ) ; +#53272 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61022, 'distance_accuracy_value', 'NONE'); +#53273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #748, 'distance_accuracy_value', 'NONE'); +#53274 = CARTESIAN_POINT ( 'NONE', ( 5.929425999999999419, 10.11080899999999971, 0.8648700000000000276 ) ) ; +#53275 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#53276 = PLANE ( 'NONE', #36738 ) ; +#53277 = PRESENTATION_STYLE_ASSIGNMENT (( #21122 ) ) ; +#53278 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35094 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81657, #89296, #91285 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53279 = FACE_OUTER_BOUND ( 'NONE', #21611, .T. ) ; +#53280 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639518, -0.9000000000000001332, 0.000000000000000000 ) ) ; +#53281 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#53282 = ORIENTED_EDGE ( 'NONE', *, *, #10067, .T. ) ; +#53283 = VECTOR ( 'NONE', #10574, 1000.000000000000114 ) ; +#53284 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000059508, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#53285 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73080, 'distance_accuracy_value', 'NONE'); +#53286 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40243 ) ) ; +#53287 = FILL_AREA_STYLE_COLOUR ( '', #66685 ) ; +#53288 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53289 = ORIENTED_EDGE ( 'NONE', *, *, #4238, .T. ) ; +#53290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53291 = EDGE_CURVE ( 'NONE', #95078, #59404, #1167, .T. ) ; +#53292 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8648700000000000276 ) ) ; +#53293 = LINE ( 'NONE', #55334, #33236 ) ; +#53294 = AXIS2_PLACEMENT_3D ( 'NONE', #90845, #52550, #51063 ) ; +#53295 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#53296 = PRESENTATION_STYLE_ASSIGNMENT (( #67092 ) ) ; +#53297 = EDGE_CURVE ( 'NONE', #59388, #9663, #40509, .T. ) ; +#53298 = ORIENTED_EDGE ( 'NONE', *, *, #98753, .F. ) ; +#53299 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53300 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40064, 'distance_accuracy_value', 'NONE'); +#53302 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74522 ), #9190 ) ; +#53301 = SURFACE_SIDE_STYLE ('',( #5778 ) ) ; +#53303 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53304 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#53305 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36830, #77121, #85277, #84290, #91445, #69437, #29648, #59851, #30136 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000013323, 0.3750000000000021649, 0.5000000000000029976, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53306 = ORIENTED_EDGE ( 'NONE', *, *, #33521, .T. ) ; +#53307 = VECTOR ( 'NONE', #19834, 1000.000000000000000 ) ; +#53308 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#53309 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53310 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53312 = VERTEX_POINT ( 'NONE', #96593 ) ; +#53313 = SURFACE_STYLE_FILL_AREA ( #37500 ) ; +#53314 = AXIS2_PLACEMENT_3D ( 'NONE', #56345, #21751, #100738 ) ; +#53315 = EDGE_CURVE ( 'NONE', #81292, #68558, #26699, .T. ) ; +#53316 = ADVANCED_FACE ( 'NONE', ( #87450 ), #50198, .T. ) ; +#53317 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53318 = VERTEX_POINT ( 'NONE', #97096 ) ; +#53320 = ORIENTED_EDGE ( 'NONE', *, *, #17983, .F. ) ; +#53319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53321 = SURFACE_SIDE_STYLE ('',( #16481 ) ) ; +#53323 = SURFACE_STYLE_FILL_AREA ( #69614 ) ; +#53322 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#53324 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#53325 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53326 = VERTEX_POINT ( 'NONE', #87957 ) ; +#53327 = PLANE ( 'NONE', #89108 ) ; +#53328 = ORIENTED_EDGE ( 'NONE', *, *, #71924, .T. ) ; +#53329 = CARTESIAN_POINT ( 'NONE', ( -0.008296387702179356879, -1.079054418458129883, 0.8100000000001278400 ) ) ; +#53330 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53331 = EDGE_CURVE ( 'NONE', #71466, #24973, #88459, .T. ) ; +#53332 = EDGE_LOOP ( 'NONE', ( #38100, #14841, #25318, #12436 ) ) ; +#53333 = VECTOR ( 'NONE', #8941, 1000.000000000000000 ) ; +#53334 = LINE ( 'NONE', #77298, #4768 ) ; +#53335 = ORIENTED_EDGE ( 'NONE', *, *, #56882, .T. ) ; +#53336 = EDGE_CURVE ( 'NONE', #40015, #84076, #25208, .T. ) ; +#53337 = LINE ( 'NONE', #69097, #63034 ) ; +#53338 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17446 ), #9226 ) ; +#53339 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4952, #98822, #28474, #13565 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53340 = VECTOR ( 'NONE', #47336, 1000.000000000000000 ) ; +#53341 = ORIENTED_EDGE ( 'NONE', *, *, #9299, .T. ) ; +#53342 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53343 = ORIENTED_EDGE ( 'NONE', *, *, #63886, .F. ) ; +#53344 = FILL_AREA_STYLE ('',( #99683 ) ) ; +#53346 = PRESENTATION_STYLE_ASSIGNMENT (( #23214 ) ) ; +#53345 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#53347 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43080, 'distance_accuracy_value', 'NONE'); +#53348 = SURFACE_STYLE_USAGE ( .BOTH. , #30330 ) ; +#53349 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#53350 = CARTESIAN_POINT ( 'NONE', ( 1.342785358116189931, -1.072184731453450057, 0.8299999999999999600 ) ) ; +#53351 = SURFACE_SIDE_STYLE ('',( #30334 ) ) ; +#53352 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53353 = ORIENTED_EDGE ( 'NONE', *, *, #35776, .T. ) ; +#53354 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53355 = STYLED_ITEM ( 'NONE', ( #13360 ), #24434 ) ; +#53356 = STYLED_ITEM ( 'NONE', ( #81666 ), #62566 ) ; +#53357 = ADVANCED_FACE ( 'NONE', ( #3689 ), #96091, .T. ) ; +#53359 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#53358 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#53360 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53361 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.05000000000000000278, 0.1900000000000000022 ) ) ; +#53362 = AXIS2_PLACEMENT_3D ( 'NONE', #30784, #71636, #86441 ) ; +#53363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53364 = PRESENTATION_STYLE_ASSIGNMENT (( #37057 ) ) ; +#53365 = ADVANCED_FACE ( 'NONE', ( #50694 ), #17485, .F. ) ; +#53366 = CLOSED_SHELL ( 'NONE', ( #31874, #75697, #51299, #29353, #80831, #67156 ) ) ; +#53367 = LINE ( 'NONE', #47208, #95027 ) ; +#53368 = ORIENTED_EDGE ( 'NONE', *, *, #21460, .F. ) ; +#53369 = MANIFOLD_SOLID_BREP ( 'ÊäÈë12', #66351 ) ; +#53370 = STYLED_ITEM ( 'NONE', ( #81539 ), #40027 ) ; +#53371 = LINE ( 'NONE', #75343, #65729 ) ; +#53372 = VECTOR ( 'NONE', #24043, 1000.000000000000000 ) ; +#53373 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53374 = PLANE ( 'NONE', #24135 ) ; +#53375 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54850, 'distance_accuracy_value', 'NONE'); +#53376 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53377 = FILL_AREA_STYLE_COLOUR ( '', #32666 ) ; +#53378 = VECTOR ( 'NONE', #100006, 1000.000000000000000 ) ; +#53379 = CARTESIAN_POINT ( 'NONE', ( 1.633333333333323312, 3.500000000000000000, 0.000000000000000000 ) ) ; +#53380 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53381 = LINE ( 'NONE', #29877, #65455 ) ; +#53382 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#53383 = SURFACE_STYLE_FILL_AREA ( #75851 ) ; +#53384 = EDGE_CURVE ( 'NONE', #64141, #77581, #21475, .T. ) ; +#53385 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53386 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59274, 'distance_accuracy_value', 'NONE'); +#53387 = FILL_AREA_STYLE_COLOUR ( '', #99406 ) ; +#53388 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53389 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8738, 'distance_accuracy_value', 'NONE'); +#53390 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8100000000000000533 ) ) ; +#53391 = FILL_AREA_STYLE_COLOUR ( '', #40602 ) ; +#53392 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#53393 = SURFACE_STYLE_FILL_AREA ( #100229 ) ; +#53394 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53395 = VERTEX_POINT ( 'NONE', #67954 ) ; +#53396 = ADVANCED_FACE ( 'NONE', ( #12277 ), #66480, .F. ) ; +#53397 = LINE ( 'NONE', #38576, #51898 ) ; +#53398 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82871, 'distance_accuracy_value', 'NONE'); +#53399 = AXIS2_PLACEMENT_3D ( 'NONE', #82564, #26427, #88692 ) ; +#53400 = FACE_OUTER_BOUND ( 'NONE', #5927, .T. ) ; +#53401 = AXIS2_PLACEMENT_3D ( 'NONE', #26386, #27379, #10428 ) ; +#53402 = ORIENTED_EDGE ( 'NONE', *, *, #92691, .F. ) ; +#53403 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#53404 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999467, -3.149999999999999911, 0.000000000000000000 ) ) ; +#53405 = FACE_OUTER_BOUND ( 'NONE', #78043, .T. ) ; +#53406 = VECTOR ( 'NONE', #61673, 1000.000000000000000 ) ; +#53407 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#53408 = EDGE_CURVE ( 'NONE', #31808, #38257, #69467, .T. ) ; +#53409 = ORIENTED_EDGE ( 'NONE', *, *, #89534, .F. ) ; +#53410 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53411 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#53412 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71822, 'distance_accuracy_value', 'NONE'); +#53413 = VECTOR ( 'NONE', #71869, 1000.000000000000000 ) ; +#53414 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84379 ) ) ; +#53415 = CARTESIAN_POINT ( 'NONE', ( -1.632862398863140093E-18, 0.8199999999999998401, 0.04999999999999998890 ) ) ; +#53416 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53417 = EDGE_CURVE ( 'NONE', #90840, #13836, #75032, .T. ) ; +#53418 = PLANE ( 'NONE', #25760 ) ; +#53419 = VECTOR ( 'NONE', #99123, 1000.000000000000000 ) ; +#53420 = VERTEX_POINT ( 'NONE', #53677 ) ; +#53421 = VERTEX_POINT ( 'NONE', #69984 ) ; +#53422 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53423 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53424 = EDGE_LOOP ( 'NONE', ( #1802, #44674, #3772, #44791 ) ) ; +#53425 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53426 = STYLED_ITEM ( 'NONE', ( #71298 ), #79317 ) ; +#53427 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53428 = FILL_AREA_STYLE ('',( #38116 ) ) ; +#53429 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53430 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53431 = EDGE_CURVE ( 'NONE', #76154, #87220, #100501, .T. ) ; +#53432 = EDGE_CURVE ( 'NONE', #19914, #91350, #61370, .T. ) ; +#53433 = AXIS2_PLACEMENT_3D ( 'NONE', #37636, #85583, #15089 ) ; +#53434 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #18927, #63008 ) ; +#53435 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53436 = ORIENTED_EDGE ( 'NONE', *, *, #70361, .F. ) ; +#53437 = AXIS2_PLACEMENT_3D ( 'NONE', #8831, #32917, #100701 ) ; +#53438 = EDGE_CURVE ( 'NONE', #15383, #58769, #1965, .T. ) ; +#53439 = ORIENTED_EDGE ( 'NONE', *, *, #37145, .F. ) ; +#53440 = EDGE_CURVE ( 'NONE', #54630, #10498, #61854, .T. ) ; +#53441 = FILL_AREA_STYLE_COLOUR ( '', #93215 ) ; +#53442 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54564 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34239, #72019, #58236 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53443 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84407 ) ) ; +#53445 = LINE ( 'NONE', #82587, #12056 ) ; +#53444 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#53446 = PLANE ( 'NONE', #34978 ) ; +#53447 = CLOSED_SHELL ( 'NONE', ( #55950, #11506, #10728, #16972, #14924, #57743 ) ) ; +#53449 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40420 ) ) ; +#53448 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#53450 = CYLINDRICAL_SURFACE ( 'NONE', #26195, 0.05000000000000012768 ) ; +#53451 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69743 ) ) ; +#53452 = ADVANCED_FACE ( 'NONE', ( #7112 ), #8121, .F. ) ; +#53453 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#53454 = ORIENTED_EDGE ( 'NONE', *, *, #31780, .F. ) ; +#53455 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97443 ) ) ; +#53457 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53456 = SURFACE_SIDE_STYLE ('',( #83598 ) ) ; +#53458 = VERTEX_POINT ( 'NONE', #39343 ) ; +#53459 = ORIENTED_EDGE ( 'NONE', *, *, #88012, .T. ) ; +#53460 = CARTESIAN_POINT ( 'NONE', ( 1.086367759722999926, -1.195322104373920169, 0.8100000000000000533 ) ) ; +#53461 = EDGE_CURVE ( 'NONE', #66922, #68837, #94470, .T. ) ; +#53462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40426 ), #98975 ) ; +#53464 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#53463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53465 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53466 = FILL_AREA_STYLE_COLOUR ( '', #44054 ) ; +#53467 = LINE ( 'NONE', #84584, #31016 ) ; +#53468 = EDGE_LOOP ( 'NONE', ( #24607, #3259, #75485, #40146, #85373, #13002 ) ) ; +#53469 = AXIS2_PLACEMENT_3D ( 'NONE', #91306, #98876, #14149 ) ; +#53470 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#53471 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #26012, #32663, #18297, #25511 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53472 = ORIENTED_EDGE ( 'NONE', *, *, #35052, .F. ) ; +#53473 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#53474 = LINE ( 'NONE', #54487, #55997 ) ; +#53475 = EDGE_LOOP ( 'NONE', ( #26060, #57036, #62240, #28318 ) ) ; +#53476 = ORIENTED_EDGE ( 'NONE', *, *, #80058, .T. ) ; +#53478 = LINE ( 'NONE', #70279, #92740 ) ; +#53477 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#53479 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53480 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8099999999999827338 ) ) ; +#53481 = AXIS2_PLACEMENT_3D ( 'NONE', #64853, #2572, #10117 ) ; +#53482 = PLANE ( 'NONE', #12293 ) ; +#53483 = FILL_AREA_STYLE_COLOUR ( '', #44257 ) ; +#53484 = AXIS2_PLACEMENT_3D ( 'NONE', #5218, #21097, #45041 ) ; +#53485 = SURFACE_STYLE_USAGE ( .BOTH. , #21824 ) ; +#53486 = LINE ( 'NONE', #67766, #34709 ) ; +#53487 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53488 = ORIENTED_EDGE ( 'NONE', *, *, #88377, .T. ) ; +#53489 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53490 = EDGE_LOOP ( 'NONE', ( #90218, #95985, #42132, #65621 ) ) ; +#53491 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53492 = SURFACE_STYLE_FILL_AREA ( #71316 ) ; +#53493 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#53494 = SURFACE_STYLE_USAGE ( .BOTH. , #52002 ) ; +#53495 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53496 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#53497 = CARTESIAN_POINT ( 'NONE', ( 0.5096387987012980236, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#53498 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#53499 = EDGE_CURVE ( 'NONE', #56373, #5416, #15846, .T. ) ; +#53500 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53502 = VERTEX_POINT ( 'NONE', #86837 ) ; +#53501 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2965 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66818, #33694, #51548 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53503 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53504 = LINE ( 'NONE', #100332, #525 ) ; +#53505 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53506 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11321, #4257, #25748, #64538 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53507 = CARTESIAN_POINT ( 'NONE', ( 1.806468873558769950, -1.190451802854979979, 0.8100000000000000533 ) ) ; +#53508 = FILL_AREA_STYLE ('',( #22342 ) ) ; +#53509 = FACE_OUTER_BOUND ( 'NONE', #77012, .T. ) ; +#53510 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.500000000000000000, 3.738703894556490081E-79 ) ) ; +#53511 = SURFACE_SIDE_STYLE ('',( #31530 ) ) ; +#53512 = AXIS2_PLACEMENT_3D ( 'NONE', #4160, #59837, #20986 ) ; +#53513 = LINE ( 'NONE', #14649, #48766 ) ; +#53514 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60253 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8966, #96304, #42229 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53515 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14539 ), #30661 ) ; +#53516 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90945 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87418, #16421, #56317 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53518 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79674, 'distance_accuracy_value', 'NONE'); +#53519 = CLOSED_SHELL ( 'NONE', ( #49903, #18712, #75707, #3806, #71925, #24039 ) ) ; +#53520 = FILL_AREA_STYLE_COLOUR ( '', #100552 ) ; +#53521 = LINE ( 'NONE', #28043, #74764 ) ; +#53522 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#53523 = EDGE_LOOP ( 'NONE', ( #84994, #83111, #74897, #55993 ) ) ; +#53524 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53525 = EDGE_CURVE ( 'NONE', #87284, #27738, #47013, .T. ) ; +#53526 = LINE ( 'NONE', #93279, #44786 ) ; +#53527 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53528 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53529 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64135, 'distance_accuracy_value', 'NONE'); +#53530 = FACE_OUTER_BOUND ( 'NONE', #63991, .T. ) ; +#53531 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 10.11080899999999971, 0.8648700000000000276 ) ) ; +#53532 = SURFACE_SIDE_STYLE ('',( #23385 ) ) ; +#53533 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#53534 = ORIENTED_EDGE ( 'NONE', *, *, #64943, .T. ) ; +#53535 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#53536 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53537 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53538 = SURFACE_SIDE_STYLE ('',( #22374 ) ) ; +#53539 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9635, 'distance_accuracy_value', 'NONE'); +#53540 = FILL_AREA_STYLE_COLOUR ( '', #16977 ) ; +#53541 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3792, 'distance_accuracy_value', 'NONE'); +#53542 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#53543 = MANIFOLD_SOLID_BREP ( 'ÊäÈë185', #45238 ) ; +#53544 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53545 = EDGE_LOOP ( 'NONE', ( #46666, #10684, #54132, #79060 ) ) ; +#53546 = VERTEX_POINT ( 'NONE', #17370 ) ; +#53547 = STYLED_ITEM ( 'NONE', ( #49259 ), #32023 ) ; +#53548 = ORIENTED_EDGE ( 'NONE', *, *, #64972, .F. ) ; +#53549 = SURFACE_SIDE_STYLE ('',( #14690 ) ) ; +#53550 = FILL_AREA_STYLE ('',( #54047 ) ) ; +#53551 = FACE_OUTER_BOUND ( 'NONE', #60270, .T. ) ; +#53552 = LINE ( 'NONE', #60721, #31682 ) ; +#53553 = LINE ( 'NONE', #75520, #83839 ) ; +#53554 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76347 ), #86115 ) ; +#53555 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #34486 ) ; +#53556 = LINE ( 'NONE', #15188, #70345 ) ; +#53557 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#53559 = VERTEX_POINT ( 'NONE', #95972 ) ; +#53558 = ORIENTED_EDGE ( 'NONE', *, *, #57381, .F. ) ; +#53560 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12132, #50055, #65848, #18343, #80685, #35229, #81191, #3567, #43351, #96954, #19367, #50553, #89817, #4051, #97453, #19874, #74523, #35729, #10607 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 0.08440948425954797329, 0.1628031558198339557, 0.2355606535845109484, 0.3043567275352200285, 0.3677451562076700098, 0.4280479426939729493, 0.4850950643867849577, 0.5394703001303209344, 0.5930068297189590165, 0.6465109772510510000, 0.7004738425458379991, 0.7551739202497640413, 0.8118926666184910212, 0.8716662319150270122, 0.9341705473199373166, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53561 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53562 = ORIENTED_EDGE ( 'NONE', *, *, #83352, .F. ) ; +#53563 = ADVANCED_FACE ( 'NONE', ( #55216 ), #2577, .T. ) ; +#53564 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53565 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69859 ), #1378 ) ; +#53566 = CARTESIAN_POINT ( 'NONE', ( -0.8116130169878562617, 1.464383040805290026, 0.8299999999999999600 ) ) ; +#53568 = LINE ( 'NONE', #28565, #10368 ) ; +#53567 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.299999999999999822, -1.507334416018511324E-89 ) ) ; +#53569 = ORIENTED_EDGE ( 'NONE', *, *, #41310, .F. ) ; +#53570 = ORIENTED_EDGE ( 'NONE', *, *, #51835, .F. ) ; +#53571 = STYLED_ITEM ( 'NONE', ( #14868 ), #79828 ) ; +#53573 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53572 = SURFACE_STYLE_FILL_AREA ( #30539 ) ; +#53574 = CARTESIAN_POINT ( 'NONE', ( -0.4700584699050159854, -0.9114593501573470258, 0.8299999999999999600 ) ) ; +#53575 = VERTEX_POINT ( 'NONE', #10122 ) ; +#53576 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#53577 = ORIENTED_EDGE ( 'NONE', *, *, #81479, .F. ) ; +#53578 = EDGE_LOOP ( 'NONE', ( #99664, #5674, #90781, #98246 ) ) ; +#53579 = PLANE ( 'NONE', #60747 ) ; +#53580 = EDGE_CURVE ( 'NONE', #96590, #54090, #33224, .T. ) ; +#53581 = VECTOR ( 'NONE', #77566, 1000.000000000000000 ) ; +#53582 = VECTOR ( 'NONE', #18194, 1000.000000000000000 ) ; +#53583 = PLANE ( 'NONE', #68892 ) ; +#53584 = PRESENTATION_STYLE_ASSIGNMENT (( #62761 ) ) ; +#53585 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64950 ), #20928 ) ; +#53588 = ORIENTED_EDGE ( 'NONE', *, *, #24828, .T. ) ; +#53587 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38625, 'distance_accuracy_value', 'NONE'); +#53586 = FILL_AREA_STYLE_COLOUR ( '', #44549 ) ; +#53590 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53589 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.600000000000000089, -0.1499999999999999944 ) ) ; +#53591 = SURFACE_SIDE_STYLE ('',( #61767 ) ) ; +#53592 = ORIENTED_EDGE ( 'NONE', *, *, #33456, .T. ) ; +#53593 = CARTESIAN_POINT ( 'NONE', ( -0.01972870844762369957, -1.247965265924660061, 0.8299999999999999600 ) ) ; +#53594 = VERTEX_POINT ( 'NONE', #64356 ) ; +#53595 = ORIENTED_EDGE ( 'NONE', *, *, #4713, .F. ) ; +#53596 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53597 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68216 ), #91051 ) ; +#53599 = CARTESIAN_POINT ( 'NONE', ( 0.1073457792207790085, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#53598 = AXIS2_PLACEMENT_3D ( 'NONE', #50906, #27405, #97307 ) ; +#53600 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#53601 = PRESENTATION_STYLE_ASSIGNMENT (( #92375 ) ) ; +#53602 = EDGE_CURVE ( 'NONE', #75149, #71482, #80707, .T. ) ; +#53603 = CARTESIAN_POINT ( 'NONE', ( 0.2440989101500280201, -0.9342297348062970075, 0.8300000000000020695 ) ) ; +#53604 = STYLED_ITEM ( 'NONE', ( #84968 ), #50207 ) ; +#53605 = EDGE_LOOP ( 'NONE', ( #60555, #68820, #1451, #69946 ) ) ; +#53606 = CARTESIAN_POINT ( 'NONE', ( 0.4459649354204920368, -1.149076952450200029, 0.8299999999999999600 ) ) ; +#53607 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, -0.1499999999999999944 ) ) ; +#53608 = ORIENTED_EDGE ( 'NONE', *, *, #85219, .F. ) ; +#53609 = LINE ( 'NONE', #24510, #19534 ) ; +#53610 = LINE ( 'NONE', #99942, #21996 ) ; +#53611 = VECTOR ( 'NONE', #73619, 1000.000000000000000 ) ; +#53612 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40266, 'distance_accuracy_value', 'NONE'); +#53613 = LINE ( 'NONE', #13728, #47979 ) ; +#53614 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#53616 = SURFACE_STYLE_USAGE ( .BOTH. , #77084 ) ; +#53615 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8991599999999999593 ) ) ; +#53617 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53618 = EDGE_CURVE ( 'NONE', #65057, #60913, #41890, .T. ) ; +#53619 = SURFACE_STYLE_USAGE ( .BOTH. , #100438 ) ; +#53620 = FACE_OUTER_BOUND ( 'NONE', #18371, .T. ) ; +#53621 = PLANE ( 'NONE', #83713 ) ; +#53622 = AXIS2_PLACEMENT_3D ( 'NONE', #59721, #13623, #44812 ) ; +#53623 = LINE ( 'NONE', #92394, #9728 ) ; +#53624 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97595 ) ) ; +#53625 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#53626 = LINE ( 'NONE', #45415, #47247 ) ; +#53628 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53627 = FACE_OUTER_BOUND ( 'NONE', #38381, .T. ) ; +#53629 = FILL_AREA_STYLE ('',( #30606 ) ) ; +#53630 = SURFACE_STYLE_FILL_AREA ( #73716 ) ; +#53631 = STYLED_ITEM ( 'NONE', ( #44140 ), #56927 ) ; +#53632 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75871 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35476, #89572, #42111 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53633 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31431, 'distance_accuracy_value', 'NONE'); +#53634 = ORIENTED_EDGE ( 'NONE', *, *, #64022, .T. ) ; +#53635 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#53636 = VECTOR ( 'NONE', #73011, 1000.000000000000000 ) ; +#53637 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53638 = PRESENTATION_STYLE_ASSIGNMENT (( #83277 ) ) ; +#53639 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78195, #76166, #53697, #77675 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53640 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#53641 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53642 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83019 ), #100801 ) ; +#53643 = FACE_OUTER_BOUND ( 'NONE', #78409, .T. ) ; +#53644 = LINE ( 'NONE', #84766, #58770 ) ; +#53645 = EDGE_CURVE ( 'NONE', #31335, #22278, #3077, .T. ) ; +#53646 = VECTOR ( 'NONE', #11058, 1000.000000000000000 ) ; +#53647 = ORIENTED_EDGE ( 'NONE', *, *, #1064, .T. ) ; +#53648 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53649 = ORIENTED_EDGE ( 'NONE', *, *, #81394, .T. ) ; +#53650 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25983 ), #29167 ) ; +#53651 = CYLINDRICAL_SURFACE ( 'NONE', #19342, 0.1000000000000000194 ) ; +#53652 = PRESENTATION_STYLE_ASSIGNMENT (( #8093 ) ) ; +#53653 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53654 = VECTOR ( 'NONE', #11871, 1000.000000000000000 ) ; +#53655 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999689, 0.7099999999999999645, -0.9464466094067259805 ) ) ; +#53656 = LINE ( 'NONE', #38338, #47273 ) ; +#53657 = FILL_AREA_STYLE_COLOUR ( '', #24032 ) ; +#53658 = CARTESIAN_POINT ( 'NONE', ( -0.6674107142857140795, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#53659 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.000000000000000000 ) ) ; +#53660 = ORIENTED_EDGE ( 'NONE', *, *, #50081, .T. ) ; +#53661 = EDGE_CURVE ( 'NONE', #89321, #93205, #40386, .T. ) ; +#53662 = FILL_AREA_STYLE_COLOUR ( '', #21566 ) ; +#53663 = ORIENTED_EDGE ( 'NONE', *, *, #64301, .T. ) ; +#53664 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#53665 = SURFACE_STYLE_USAGE ( .BOTH. , #14298 ) ; +#53666 = ORIENTED_EDGE ( 'NONE', *, *, #15240, .F. ) ; +#53667 = STYLED_ITEM ( 'NONE', ( #61428 ), #50903 ) ; +#53668 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53669 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53670 = FILL_AREA_STYLE_COLOUR ( '', #5429 ) ; +#53671 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53672 = SURFACE_SIDE_STYLE ('',( #15842 ) ) ; +#53674 = ORIENTED_EDGE ( 'NONE', *, *, #43953, .T. ) ; +#53673 = ORIENTED_EDGE ( 'NONE', *, *, #54653, .F. ) ; +#53676 = AXIS2_PLACEMENT_3D ( 'NONE', #23389, #46334, #63730 ) ; +#53675 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#53677 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, 0.000000000000000000 ) ) ; +#53678 = VERTEX_POINT ( 'NONE', #32264 ) ; +#53679 = EDGE_CURVE ( 'NONE', #40383, #18482, #46539, .T. ) ; +#53680 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#53682 = CARTESIAN_POINT ( 'NONE', ( -0.4484892475557449854, -1.042938524989579951, 0.8100000000000000533 ) ) ; +#53681 = LINE ( 'NONE', #84804, #89673 ) ; +#53683 = EDGE_LOOP ( 'NONE', ( #58005, #47303, #17967, #22587 ) ) ; +#53684 = ORIENTED_EDGE ( 'NONE', *, *, #7932, .F. ) ; +#53685 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#53686 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53687 = STYLED_ITEM ( 'NONE', ( #6361 ), #32448 ) ; +#53688 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15561 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82480, #81498, #19677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53689 = FACE_OUTER_BOUND ( 'NONE', #28546, .T. ) ; +#53690 = LINE ( 'NONE', #8634, #57981 ) ; +#53691 = ORIENTED_EDGE ( 'NONE', *, *, #66993, .F. ) ; +#53692 = ORIENTED_EDGE ( 'NONE', *, *, #83755, .F. ) ; +#53693 = ORIENTED_EDGE ( 'NONE', *, *, #32004, .T. ) ; +#53694 = EDGE_CURVE ( 'NONE', #2565, #57725, #86376, .T. ) ; +#53695 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53696 = AXIS2_PLACEMENT_3D ( 'NONE', #46113, #93572, #30824 ) ; +#53698 = ORIENTED_EDGE ( 'NONE', *, *, #32071, .F. ) ; +#53697 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.216666666666666785, 0.000000000000000000 ) ) ; +#53699 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97675 ) ) ; +#53700 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53701 = FILL_AREA_STYLE ('',( #54209 ) ) ; +#53702 = VERTEX_POINT ( 'NONE', #25136 ) ; +#53703 = AXIS2_PLACEMENT_3D ( 'NONE', #49368, #1402, #81042 ) ; +#53704 = FILL_AREA_STYLE_COLOUR ( '', #89180 ) ; +#53705 = VERTEX_POINT ( 'NONE', #56271 ) ; +#53706 = MANIFOLD_SOLID_BREP ( 'ÊäÈë133', #90979 ) ; +#53707 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 9.350000000000001421, 0.000000000000000000 ) ) ; +#53708 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53709 = ORIENTED_EDGE ( 'NONE', *, *, #41926, .T. ) ; +#53710 = LINE ( 'NONE', #75, #65317 ) ; +#53711 = SURFACE_STYLE_FILL_AREA ( #22562 ) ; +#53713 = LINE ( 'NONE', #73571, #20504 ) ; +#53712 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53714 = CARTESIAN_POINT ( 'NONE', ( -0.9130688375731768058, -1.312528618838266548, 0.8099999999997579136 ) ) ; +#53715 = EDGE_CURVE ( 'NONE', #94240, #3632, #48606, .T. ) ; +#53716 = VECTOR ( 'NONE', #15166, 1000.000000000000000 ) ; +#53717 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53718 = CARTESIAN_POINT ( 'NONE', ( 1.736362623504380087, -1.223383224893549892, 0.8099999999999996092 ) ) ; +#53719 = ORIENTED_EDGE ( 'NONE', *, *, #1368, .F. ) ; +#53720 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#53721 = STYLED_ITEM ( 'NONE', ( #79284 ), #42433 ) ; +#53722 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53723 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53724 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44511 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25494, #71944, #70932 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53725 = SURFACE_STYLE_USAGE ( .BOTH. , #14867 ) ; +#53726 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#53727 = FACE_OUTER_BOUND ( 'NONE', #56121, .T. ) ; +#53728 = EDGE_CURVE ( 'NONE', #90254, #61084, #47054, .T. ) ; +#53729 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#53730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60336 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24013, #68418, #13747 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53731 = CARTESIAN_POINT ( 'NONE', ( 7.032513000000000680, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#53732 = VERTEX_POINT ( 'NONE', #39394 ) ; +#53733 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#53734 = ORIENTED_EDGE ( 'NONE', *, *, #43450, .F. ) ; +#53736 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#53735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53737 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#53738 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12915 ) ) ; +#53739 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#53740 = ORIENTED_EDGE ( 'NONE', *, *, #15798, .T. ) ; +#53741 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#53742 = PRESENTATION_STYLE_ASSIGNMENT (( #22603 ) ) ; +#53743 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53744 = SURFACE_SIDE_STYLE ('',( #45050 ) ) ; +#53745 = FACE_OUTER_BOUND ( 'NONE', #21264, .T. ) ; +#53746 = PLANE ( 'NONE', #9388 ) ; +#53747 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53748 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53749 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53750 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53752 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#53753 = EDGE_CURVE ( 'NONE', #86671, #98596, #2131, .T. ) ; +#53754 = EDGE_CURVE ( 'NONE', #73043, #3859, #31238, .T. ) ; +#53755 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11712 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24978, #71411, #56112 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53756 = SURFACE_SIDE_STYLE ('',( #30754 ) ) ; +#53757 = EDGE_LOOP ( 'NONE', ( #45313, #5626, #65373, #100394 ) ) ; +#53758 = ORIENTED_EDGE ( 'NONE', *, *, #26287, .F. ) ; +#53759 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.266666666666647068, 3.495651678170021751E-76 ) ) ; +#53760 = VECTOR ( 'NONE', #58273, 1000.000000000000000 ) ; +#53761 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#53762 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#53763 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #284 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3323, #34490, #33473 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53764 = AXIS2_PLACEMENT_3D ( 'NONE', #32191, #1554, #85785 ) ; +#53765 = CARTESIAN_POINT ( 'NONE', ( -0.9232862852897980588, -1.401385721107119897, 0.8299999999999981837 ) ) ; +#53766 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53767 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#53768 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, -0.1499999999999999944 ) ) ; +#53769 = LINE ( 'NONE', #35973, #14114 ) ; +#53770 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53771 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#53772 = SURFACE_STYLE_USAGE ( .BOTH. , #24681 ) ; +#53773 = ORIENTED_EDGE ( 'NONE', *, *, #18901, .F. ) ; +#53774 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#53775 = ADVANCED_FACE ( 'NONE', ( #70540 ), #31742, .T. ) ; +#53776 = SURFACE_STYLE_USAGE ( .BOTH. , #83917 ) ; +#53777 = VECTOR ( 'NONE', #97227, 1000.000000000000000 ) ; +#53778 = EDGE_CURVE ( 'NONE', #74902, #12657, #100086, .T. ) ; +#53779 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#53780 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, 3.500000000000000444, 0.000000000000000000 ) ) ; +#53781 = ORIENTED_EDGE ( 'NONE', *, *, #33886, .F. ) ; +#53782 = PLANE ( 'NONE', #33202 ) ; +#53783 = ADVANCED_FACE ( 'NONE', ( #2626 ), #26128, .F. ) ; +#53784 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53785 = FACE_OUTER_BOUND ( 'NONE', #100257, .T. ) ; +#53786 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53787 = AXIS2_PLACEMENT_3D ( 'NONE', #95130, #69639, #63549 ) ; +#53788 = LINE ( 'NONE', #32329, #63763 ) ; +#53789 = SURFACE_SIDE_STYLE ('',( #70095 ) ) ; +#53790 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74489 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83014, #65679, #58061 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53791 = EDGE_LOOP ( 'NONE', ( #95734, #93810, #40632, #59804 ) ) ; +#53792 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50313 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95372, #17280, #49985 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53793 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58714 ) ) ; +#53794 = EDGE_CURVE ( 'NONE', #93808, #66638, #81266, .T. ) ; +#53795 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#53796 = ORIENTED_EDGE ( 'NONE', *, *, #7460, .T. ) ; +#53797 = EDGE_CURVE ( 'NONE', #95182, #87071, #19950, .T. ) ; +#53798 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71969 ), #27963 ) ; +#53799 = SURFACE_STYLE_FILL_AREA ( #669 ) ; +#53800 = SURFACE_STYLE_USAGE ( .BOTH. , #76771 ) ; +#53801 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#53802 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#53803 = SURFACE_STYLE_USAGE ( .BOTH. , #23172 ) ; +#53804 = ORIENTED_EDGE ( 'NONE', *, *, #12413, .T. ) ; +#53805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53806 = ORIENTED_EDGE ( 'NONE', *, *, #55155, .F. ) ; +#53807 = VECTOR ( 'NONE', #22879, 1000.000000000000000 ) ; +#53808 = ADVANCED_FACE ( 'NONE', ( #11689 ), #49105, .F. ) ; +#53809 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28368, 'distance_accuracy_value', 'NONE'); +#53810 = EDGE_CURVE ( 'NONE', #93323, #90974, #67571, .T. ) ; +#53811 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53812 = ORIENTED_EDGE ( 'NONE', *, *, #28419, .T. ) ; +#53814 = ORIENTED_EDGE ( 'NONE', *, *, #48637, .F. ) ; +#53813 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53815 = SURFACE_STYLE_FILL_AREA ( #22673 ) ; +#53817 = SURFACE_SIDE_STYLE ('',( #53323 ) ) ; +#53816 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#53818 = SURFACE_STYLE_FILL_AREA ( #70125 ) ; +#53819 = ORIENTED_EDGE ( 'NONE', *, *, #32133, .F. ) ; +#53820 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#53821 = ORIENTED_EDGE ( 'NONE', *, *, #84185, .F. ) ; +#53822 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#53823 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1350000000000000089 ) ) ; +#53824 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53825 = SURFACE_STYLE_FILL_AREA ( #60512 ) ; +#53826 = ORIENTED_EDGE ( 'NONE', *, *, #82713, .F. ) ; +#53827 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#53828 = ORIENTED_EDGE ( 'NONE', *, *, #26524, .T. ) ; +#53829 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94547 ), #99435 ) ; +#53830 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97798 ) ) ; +#53831 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6465 ) ) ; +#53833 = SURFACE_SIDE_STYLE ('',( #94104 ) ) ; +#53832 = PRESENTATION_STYLE_ASSIGNMENT (( #47171 ) ) ; +#53834 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#53835 = ADVANCED_FACE ( 'NONE', ( #58294 ), #58792, .F. ) ; +#53836 = PLANE ( 'NONE', #78273 ) ; +#53837 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53838 = ORIENTED_EDGE ( 'NONE', *, *, #71498, .F. ) ; +#53839 = FACE_OUTER_BOUND ( 'NONE', #6777, .T. ) ; +#53840 = ORIENTED_EDGE ( 'NONE', *, *, #47504, .F. ) ; +#53841 = STYLED_ITEM ( 'NONE', ( #4963 ), #81614 ) ; +#53842 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#53843 = SURFACE_STYLE_FILL_AREA ( #214 ) ; +#53844 = EDGE_CURVE ( 'NONE', #67009, #16425, #72558, .T. ) ; +#53845 = LINE ( 'NONE', #55390, #39071 ) ; +#53846 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53847 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14667 ), #47367 ) ; +#53849 = EDGE_CURVE ( 'NONE', #35608, #57096, #53610, .T. ) ; +#53848 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53850 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#53851 = FACE_OUTER_BOUND ( 'NONE', #804, .T. ) ; +#53852 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53853 = FILL_AREA_STYLE ('',( #98720 ) ) ; +#53854 = VERTEX_POINT ( 'NONE', #83749 ) ; +#53855 = PLANE ( 'NONE', #41598 ) ; +#53856 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43081 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97877, #58665, #20317 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53857 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8099999999997948841 ) ) ; +#53858 = AXIS2_PLACEMENT_3D ( 'NONE', #27909, #59579, #34059 ) ; +#53861 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#53860 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53859 = PLANE ( 'NONE', #49603 ) ; +#53862 = SURFACE_STYLE_USAGE ( .BOTH. , #22717 ) ; +#53863 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51986, 'distance_accuracy_value', 'NONE'); +#53864 = STYLED_ITEM ( 'NONE', ( #47916 ), #68797 ) ; +#53865 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23522 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26652, #27160, #97554 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53866 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53867 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.123820061220055511, 0.000000000000000000 ) ) ; +#53868 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 0.4500000000000001221 ) ) ; +#53869 = ORIENTED_EDGE ( 'NONE', *, *, #93663, .F. ) ; +#53871 = MANIFOLD_SOLID_BREP ( 'ÊäÈë11', #71364 ) ; +#53870 = SURFACE_SIDE_STYLE ('',( #59577 ) ) ; +#53872 = FILL_AREA_STYLE_COLOUR ( '', #18469 ) ; +#53873 = FACE_OUTER_BOUND ( 'NONE', #97823, .T. ) ; +#53874 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.266666666666647068, 3.495651678170021751E-76 ) ) ; +#53875 = CARTESIAN_POINT ( 'NONE', ( -0.1098982853935999981, -1.445363849546990043, 0.8299999999999999600 ) ) ; +#53876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6500 ) ) ; +#53877 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53878 = AXIS2_PLACEMENT_3D ( 'NONE', #37690, #7948, #99364 ) ; +#53879 = CARTESIAN_POINT ( 'NONE', ( 0.5854301948051945370, 0.7099999999999999645, 0.2077922077922077504 ) ) ; +#53880 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#53881 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#53882 = SURFACE_STYLE_FILL_AREA ( #22231 ) ; +#53883 = EDGE_CURVE ( 'NONE', #7722, #46370, #59525, .T. ) ; +#53884 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8299999999999999600 ) ) ; +#53885 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53886 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53887 = FACE_OUTER_BOUND ( 'NONE', #79956, .T. ) ; +#53888 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#53889 = PRESENTATION_STYLE_ASSIGNMENT (( #31404 ) ) ; +#53890 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53891 = SURFACE_STYLE_FILL_AREA ( #77353 ) ; +#53892 = SURFACE_STYLE_FILL_AREA ( #76873 ) ; +#53893 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, -3.738329090730020644E-17, -0.8499999999999999778 ) ) ; +#53894 = FILL_AREA_STYLE_COLOUR ( '', #33654 ) ; +#53895 = CYLINDRICAL_SURFACE ( 'NONE', #34116, 0.1200000000000000927 ) ; +#53896 = PLANE ( 'NONE', #52611 ) ; +#53897 = EDGE_LOOP ( 'NONE', ( #64616, #74606, #28519, #9206 ) ) ; +#53898 = LINE ( 'NONE', #25306, #3061 ) ; +#53899 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#53900 = EDGE_CURVE ( 'NONE', #22697, #65708, #60784, .T. ) ; +#53901 = SURFACE_STYLE_FILL_AREA ( #23781 ) ; +#53902 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53903 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53904 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#53905 = VERTEX_POINT ( 'NONE', #45895 ) ; +#53906 = ADVANCED_FACE ( 'NONE', ( #22449 ), #76072, .T. ) ; +#53907 = VECTOR ( 'NONE', #63032, 1000.000000000000000 ) ; +#53908 = VECTOR ( 'NONE', #8787, 1000.000000000000000 ) ; +#53909 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#53910 = VECTOR ( 'NONE', #93259, 1000.000000000000000 ) ; +#53911 = FILL_AREA_STYLE_COLOUR ( '', #27684 ) ; +#53912 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.149999999999970157, 0.000000000000000000 ) ) ; +#53913 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#53914 = VERTEX_POINT ( 'NONE', #29606 ) ; +#53915 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70145 ) ) ; +#53917 = FILL_AREA_STYLE_COLOUR ( '', #40747 ) ; +#53916 = VECTOR ( 'NONE', #45094, 1000.000000000000000 ) ; +#53918 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49968, 'distance_accuracy_value', 'NONE'); +#53919 = VECTOR ( 'NONE', #20691, 1000.000000000000000 ) ; +#53920 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.099999999999999867, 4.486444673467788097E-79 ) ) ; +#53921 = VECTOR ( 'NONE', #68833, 1000.000000000000000 ) ; +#53922 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53923 = VERTEX_POINT ( 'NONE', #97984 ) ; +#53924 = VERTEX_POINT ( 'NONE', #59303 ) ; +#53925 = SURFACE_STYLE_FILL_AREA ( #47263 ) ; +#53926 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#53927 = ORIENTED_EDGE ( 'NONE', *, *, #86894, .F. ) ; +#53928 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#53929 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#53930 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78414 ), #34423 ) ; +#53931 = SURFACE_STYLE_FILL_AREA ( #76390 ) ; +#53932 = SURFACE_STYLE_USAGE ( .BOTH. , #30939 ) ; +#53933 = FILL_AREA_STYLE_COLOUR ( '', #83898 ) ; +#53934 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #15831, #10893 ) ; +#53935 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53936 = EDGE_LOOP ( 'NONE', ( #63079, #46163, #98163, #64777 ) ) ; +#53937 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#53938 = ADVANCED_FACE ( 'NONE', ( #90386 ), #59805, .T. ) ; +#53939 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15427 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25350, #40652, #41663 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53940 = VERTEX_POINT ( 'NONE', #469 ) ; +#53941 = SURFACE_STYLE_USAGE ( .BOTH. , #300 ) ; +#53942 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11992, 'distance_accuracy_value', 'NONE'); +#53944 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53943 = FILL_AREA_STYLE ('',( #29931 ) ) ; +#53945 = LINE ( 'NONE', #77919, #16988 ) ; +#53946 = ORIENTED_EDGE ( 'NONE', *, *, #68935, .T. ) ; +#53947 = SURFACE_SIDE_STYLE ('',( #29091 ) ) ; +#53948 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#53949 = ORIENTED_EDGE ( 'NONE', *, *, #67652, .T. ) ; +#53950 = ORIENTED_EDGE ( 'NONE', *, *, #62389, .T. ) ; +#53951 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #24641, #70544, #80255, #86383 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#53952 = ORIENTED_EDGE ( 'NONE', *, *, #47089, .T. ) ; +#53953 = STYLED_ITEM ( 'NONE', ( #91474 ), #10450 ) ; +#53954 = PRESENTATION_STYLE_ASSIGNMENT (( #31982 ) ) ; +#53955 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#53957 = ORIENTED_EDGE ( 'NONE', *, *, #19117, .F. ) ; +#53956 = PLANE ( 'NONE', #45983 ) ; +#53958 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.000000000000000000 ) ) ; +#53959 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999990452, -0.02000000000001254941 ) ) ; +#53960 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53961 = ORIENTED_EDGE ( 'NONE', *, *, #40650, .F. ) ; +#53963 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#53962 = LINE ( 'NONE', #30437, #25455 ) ; +#53964 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53965 = EDGE_LOOP ( 'NONE', ( #35996, #14434, #20027, #85733 ) ) ; +#53966 = ORIENTED_EDGE ( 'NONE', *, *, #76243, .T. ) ; +#53967 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#53969 = FILL_AREA_STYLE ('',( #69770 ) ) ; +#53968 = CARTESIAN_POINT ( 'NONE', ( 0.9776395701974860408, -1.395425853902759972, 0.8100000000000000533 ) ) ; +#53970 = SURFACE_SIDE_STYLE ('',( #22836 ) ) ; +#53971 = EDGE_CURVE ( 'NONE', #33336, #67267, #62793, .T. ) ; +#53972 = FILL_AREA_STYLE_COLOUR ( '', #17233 ) ; +#53973 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#53974 = FACE_OUTER_BOUND ( 'NONE', #84080, .T. ) ; +#53975 = FILL_AREA_STYLE ('',( #22318 ) ) ; +#53976 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100941 ) ; +#53977 = PRESENTATION_STYLE_ASSIGNMENT (( #22844 ) ) ; +#53978 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72096 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76220, #68044, #81907 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53979 = EDGE_LOOP ( 'NONE', ( #46748, #58031, #8742, #64382 ) ) ; +#53980 = FACE_OUTER_BOUND ( 'NONE', #12366, .T. ) ; +#53981 = VERTEX_POINT ( 'NONE', #23997 ) ; +#53982 = EDGE_CURVE ( 'NONE', #11153, #83076, #52962, .T. ) ; +#53983 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#53985 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#53984 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#53986 = PRESENTATION_STYLE_ASSIGNMENT (( #5952 ) ) ; +#53987 = FILL_AREA_STYLE ('',( #30464 ) ) ; +#53988 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#53989 = LINE ( 'NONE', #23357, #92508 ) ; +#53990 = EDGE_CURVE ( 'NONE', #99269, #2971, #8546, .T. ) ; +#53991 = FILL_AREA_STYLE ('',( #38176 ) ) ; +#53992 = EDGE_LOOP ( 'NONE', ( #41424, #62681, #72472, #65230 ) ) ; +#53993 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63130, #22801, #61621 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53994 = FILL_AREA_STYLE ('',( #91282 ) ) ; +#53995 = FACE_OUTER_BOUND ( 'NONE', #52483, .T. ) ; +#53996 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#53997 = FILL_AREA_STYLE_COLOUR ( '', #81637 ) ; +#53998 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58457 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37935, #84393, #99608 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#53999 = FILL_AREA_STYLE_COLOUR ( '', #87529 ) ; +#54001 = EDGE_CURVE ( 'NONE', #34142, #72086, #93857, .T. ) ; +#54000 = FILL_AREA_STYLE ('',( #62195 ) ) ; +#54003 = ADVANCED_FACE ( 'NONE', ( #23471 ), #79625, .T. ) ; +#54002 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#54004 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54005 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#54006 = VECTOR ( 'NONE', #1647, 1000.000000000000000 ) ; +#54007 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54008 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#54009 = VECTOR ( 'NONE', #4155, 1000.000000000000000 ) ; +#54010 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54011 = ADVANCED_FACE ( 'NONE', ( #100432 ), #38288, .T. ) ; +#54012 = EDGE_CURVE ( 'NONE', #75419, #73120, #62728, .T. ) ; +#54013 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 1.149999999999999911, 0.000000000000000000 ) ) ; +#54014 = CARTESIAN_POINT ( 'NONE', ( 1.251030810655360037, -0.9616422087329199453, 0.8299999999999995159 ) ) ; +#54015 = DIRECTION ( 'NONE', ( 0.7071060119555149237, -0.7071075504167433357, 0.000000000000000000 ) ) ; +#54016 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 2.258754526011470139E-17 ) ) ; +#54017 = CARTESIAN_POINT ( 'NONE', ( -1.166958079791611480, -1.445067339141033802, 0.8099999999996603250 ) ) ; +#54018 = VERTEX_POINT ( 'NONE', #19316 ) ; +#54019 = FACE_OUTER_BOUND ( 'NONE', #27955, .T. ) ; +#54020 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1399999999999999856 ) ) ; +#54021 = FILL_AREA_STYLE_COLOUR ( '', #17524 ) ; +#54022 = EDGE_CURVE ( 'NONE', #73738, #5169, #65282, .T. ) ; +#54023 = LINE ( 'NONE', #91316, #39403 ) ; +#54024 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8648700000000000276 ) ) ; +#54025 = LINE ( 'NONE', #85148, #53716 ) ; +#54026 = AXIS2_PLACEMENT_3D ( 'NONE', #95853, #71906, #81599 ) ; +#54027 = STYLED_ITEM ( 'NONE', ( #63389 ), #10468 ) ; +#54028 = EDGE_CURVE ( 'NONE', #83675, #19298, #26502, .T. ) ; +#54029 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54030 = FACE_OUTER_BOUND ( 'NONE', #11855, .T. ) ; +#54031 = VERTEX_POINT ( 'NONE', #17795 ) ; +#54032 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54033 = VECTOR ( 'NONE', #3812, 1000.000000000000000 ) ; +#54034 = PLANE ( 'NONE', #33408 ) ; +#54035 = CARTESIAN_POINT ( 'NONE', ( 1.803030467297160211, -1.264112177694660000, 0.8299999999999994049 ) ) ; +#54036 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54037 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54038 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #26797, #57962, #19097, #39193 ), + ( #50305, #81438, #97195, #11371 ), + ( #377, #34962, #89567, #46836 ), + ( #93772, #39701, #60462, #12373 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#54039 = FILL_AREA_STYLE ('',( #31055 ) ) ; +#54040 = MANIFOLD_SOLID_BREP ( 'ÊäÈë33', #10941 ) ; +#54041 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54042 = ORIENTED_EDGE ( 'NONE', *, *, #1213, .F. ) ; +#54043 = ORIENTED_EDGE ( 'NONE', *, *, #61994, .F. ) ; +#54044 = LINE ( 'NONE', #23402, #3062 ) ; +#54045 = ORIENTED_EDGE ( 'NONE', *, *, #88835, .T. ) ; +#54046 = SURFACE_STYLE_USAGE ( .BOTH. , #92793 ) ; +#54047 = FILL_AREA_STYLE_COLOUR ( '', #100273 ) ; +#54048 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54049 = FACE_OUTER_BOUND ( 'NONE', #36108, .T. ) ; +#54050 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60629 ) ) ; +#54051 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#54052 = VECTOR ( 'NONE', #14901, 1000.000000000000000 ) ; +#54053 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #61313 ) ; +#54054 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#54056 = ORIENTED_EDGE ( 'NONE', *, *, #40737, .F. ) ; +#54055 = ORIENTED_EDGE ( 'NONE', *, *, #71973, .T. ) ; +#54057 = EDGE_CURVE ( 'NONE', #10027, #99759, #94326, .T. ) ; +#54058 = AXIS2_PLACEMENT_3D ( 'NONE', #62168, #86626, #93737 ) ; +#54059 = VERTEX_POINT ( 'NONE', #50998 ) ; +#54060 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#54061 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45903, 'distance_accuracy_value', 'NONE'); +#54062 = SURFACE_SIDE_STYLE ('',( #92807 ) ) ; +#54064 = PRESENTATION_STYLE_ASSIGNMENT (( #22929 ) ) ; +#54063 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54065 = ORIENTED_EDGE ( 'NONE', *, *, #25856, .T. ) ; +#54066 = EDGE_CURVE ( 'NONE', #49432, #96362, #9569, .T. ) ; +#54067 = EDGE_LOOP ( 'NONE', ( #8724, #96145, #36242, #61590 ) ) ; +#54068 = VECTOR ( 'NONE', #80339, 1000.000000000000000 ) ; +#54069 = LINE ( 'NONE', #84698, #9035 ) ; +#54070 = LINE ( 'NONE', #92812, #5547 ) ; +#54071 = SURFACE_STYLE_FILL_AREA ( #92813 ) ; +#54073 = LINE ( 'NONE', #31587, #66217 ) ; +#54072 = LINE ( 'NONE', #46377, #870 ) ; +#54074 = ORIENTED_EDGE ( 'NONE', *, *, #50503, .F. ) ; +#54075 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8099999999999119016 ) ) ; +#54076 = ORIENTED_EDGE ( 'NONE', *, *, #40313, .T. ) ; +#54077 = ORIENTED_EDGE ( 'NONE', *, *, #68033, .F. ) ; +#54078 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54079 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54080 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54081 = CARTESIAN_POINT ( 'NONE', ( 7.895183000000000284, 10.29465700000000083, 0.8991599999999999593 ) ) ; +#54083 = ORIENTED_EDGE ( 'NONE', *, *, #64340, .T. ) ; +#54082 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8099999999999442091 ) ) ; +#54084 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#54085 = LINE ( 'NONE', #85202, #94554 ) ; +#54086 = ORIENTED_EDGE ( 'NONE', *, *, #28352, .F. ) ; +#54088 = SURFACE_STYLE_FILL_AREA ( #22956 ) ; +#54087 = PRESENTATION_STYLE_ASSIGNMENT (( #47937 ) ) ; +#54089 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54090 = VERTEX_POINT ( 'NONE', #73961 ) ; +#54091 = VERTEX_POINT ( 'NONE', #27008 ) ; +#54092 = SURFACE_SIDE_STYLE ('',( #78080 ) ) ; +#54093 = EDGE_CURVE ( 'NONE', #82492, #34797, #10555, .T. ) ; +#54094 = FILL_AREA_STYLE_COLOUR ( '', #43266 ) ; +#54095 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54096 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91611 ), #37775 ) ; +#54097 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54098 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#54099 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#54100 = CARTESIAN_POINT ( 'NONE', ( 0.9903538716760360572, -1.113830263093820161, 0.8299999999999997380 ) ) ; +#54102 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54101 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54783, 'distance_accuracy_value', 'NONE'); +#54103 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 3.548858000000000068, 0.8648700000000000276 ) ) ; +#54104 = VERTEX_POINT ( 'NONE', #81642 ) ; +#54105 = EDGE_LOOP ( 'NONE', ( #26558, #29460, #5988, #27617, #55535, #35595 ) ) ; +#54106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81830 ), #36196 ) ; +#54107 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54108 = FACE_OUTER_BOUND ( 'NONE', #31997, .T. ) ; +#54109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54110 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#54111 = ADVANCED_FACE ( 'NONE', ( #11578 ), #98673, .F. ) ; +#54112 = FILL_AREA_STYLE ('',( #69392 ) ) ; +#54113 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#54114 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54116 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54115 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54117 = VECTOR ( 'NONE', #7495, 1000.000000000000000 ) ; +#54118 = LINE ( 'NONE', #13743, #39805 ) ; +#54119 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#54120 = FILL_AREA_STYLE_COLOUR ( '', #79298 ) ; +#54121 = STYLED_ITEM ( 'NONE', ( #72984 ), #43380 ) ; +#54122 = AXIS2_PLACEMENT_3D ( 'NONE', #34588, #44211, #6831 ) ; +#54124 = CARTESIAN_POINT ( 'NONE', ( 3.383841999999999572, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#54123 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54125 = SURFACE_SIDE_STYLE ('',( #31146 ) ) ; +#54126 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62309 ), #47565 ) ; +#54127 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#54128 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54129 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24799 ) ) ; +#54130 = EDGE_CURVE ( 'NONE', #22507, #43256, #45278, .T. ) ; +#54131 = STYLED_ITEM ( 'NONE', ( #70248 ), #10948 ) ; +#54132 = ORIENTED_EDGE ( 'NONE', *, *, #4968, .F. ) ; +#54133 = LINE ( 'NONE', #32416, #72063 ) ; +#54134 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54135 = AXIS2_PLACEMENT_3D ( 'NONE', #39385, #17404, #96006 ) ; +#54136 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9644, 'distance_accuracy_value', 'NONE'); +#54137 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90808, 'distance_accuracy_value', 'NONE'); +#54138 = SURFACE_STYLE_FILL_AREA ( #96309 ) ; +#54139 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54140 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54141 = CARTESIAN_POINT ( 'NONE', ( -0.5610005133853439574, 2.432921575926970004, 0.8100000000000000533 ) ) ; +#54142 = PRESENTATION_STYLE_ASSIGNMENT (( #69940 ) ) ; +#54143 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54144 = EDGE_CURVE ( 'NONE', #54862, #45083, #6447, .T. ) ; +#54145 = VERTEX_POINT ( 'NONE', #74472 ) ; +#54146 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935070042, 0.8199999999999999512 ) ) ; +#54147 = ORIENTED_EDGE ( 'NONE', *, *, #17596, .T. ) ; +#54149 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40226, 'distance_accuracy_value', 'NONE'); +#54148 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9223 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15873, #8150, #47547 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54150 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49161, 'distance_accuracy_value', 'NONE'); +#54151 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54152 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54153 = SURFACE_STYLE_USAGE ( .BOTH. , #31671 ) ; +#54154 = SURFACE_STYLE_USAGE ( .BOTH. , #29173 ) ; +#54155 = CARTESIAN_POINT ( 'NONE', ( -0.2221370729066020344, -1.389169665048220148, 0.8299999999999995159 ) ) ; +#54156 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54157 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#54158 = PRESENTATION_STYLE_ASSIGNMENT (( #86299 ) ) ; +#54159 = LINE ( 'NONE', #61837, #96142 ) ; +#54160 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#54161 = VERTEX_POINT ( 'NONE', #90786 ) ; +#54162 = CARTESIAN_POINT ( 'NONE', ( 5.264744999999999564, 5.557041000000000786, 0.8648700000000000276 ) ) ; +#54163 = PRESENTATION_STYLE_ASSIGNMENT (( #6617 ) ) ; +#54164 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54165 = ORIENTED_EDGE ( 'NONE', *, *, #58324, .F. ) ; +#54166 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#54167 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60604 ) ) ; +#54168 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54169 = ORIENTED_EDGE ( 'NONE', *, *, #25152, .F. ) ; +#54170 = SURFACE_SIDE_STYLE ('',( #94952 ) ) ; +#54171 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.123820061220085265, -0.02000000000000000042 ) ) ; +#54172 = LINE ( 'NONE', #47507, #82180 ) ; +#54173 = EDGE_CURVE ( 'NONE', #36642, #64535, #20830, .T. ) ; +#54174 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54175 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 7.700000000000000178, 0.8648700000000000276 ) ) ; +#54176 = SURFACE_SIDE_STYLE ('',( #62868 ) ) ; +#54177 = CARTESIAN_POINT ( 'NONE', ( -0.5986186809950444498, 1.535305927740408416, 0.8099999999999999423 ) ) ; +#54179 = ORIENTED_EDGE ( 'NONE', *, *, #71973, .F. ) ; +#54178 = VERTEX_POINT ( 'NONE', #78471 ) ; +#54180 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62359 ), #60681 ) ; +#54181 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333319537, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#54182 = ORIENTED_EDGE ( 'NONE', *, *, #43559, .F. ) ; +#54183 = SURFACE_STYLE_FILL_AREA ( #16339 ) ; +#54184 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65567 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10966, #13477, #83519 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54186 = CARTESIAN_POINT ( 'NONE', ( -0.4617362663480760743, -1.013453039847479920, 0.8100000000000000533 ) ) ; +#54185 = PLANE ( 'NONE', #14833 ) ; +#54187 = ORIENTED_EDGE ( 'NONE', *, *, #93686, .F. ) ; +#54188 = ADVANCED_FACE ( 'NONE', ( #40190 ), #77449, .T. ) ; +#54189 = ORIENTED_EDGE ( 'NONE', *, *, #52697, .F. ) ; +#54190 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54191 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56594 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13997, #45157, #76320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54192 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#54193 = FILL_AREA_STYLE_COLOUR ( '', #74704 ) ; +#54194 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54195 = VERTEX_POINT ( 'NONE', #55015 ) ; +#54196 = ORIENTED_EDGE ( 'NONE', *, *, #96862, .F. ) ; +#54197 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#54198 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94901 ) ) ; +#54199 = ORIENTED_EDGE ( 'NONE', *, *, #61720, .T. ) ; +#54200 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54201 = AXIS2_PLACEMENT_3D ( 'NONE', #62969, #17456, #95057 ) ; +#54202 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54204 = EDGE_LOOP ( 'NONE', ( #76034, #64828, #73029, #42763 ) ) ; +#54203 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#54205 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4000000000000000222, 0.2999999999999999889 ) ) ; +#54206 = FILL_AREA_STYLE ('',( #46516 ) ) ; +#54207 = VECTOR ( 'NONE', #59523, 1000.000000000000000 ) ; +#54208 = LINE ( 'NONE', #92957, #2515 ) ; +#54209 = FILL_AREA_STYLE_COLOUR ( '', #7973 ) ; +#54210 = VERTEX_POINT ( 'NONE', #53985 ) ; +#54211 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54212 = SURFACE_STYLE_FILL_AREA ( #23573 ) ; +#54213 = VERTEX_POINT ( 'NONE', #94265 ) ; +#54214 = MANIFOLD_SOLID_BREP ( 'ÊäÈë2', #10871 ) ; +#54215 = EDGE_CURVE ( 'NONE', #70042, #21645, #81003, .T. ) ; +#54216 = CARTESIAN_POINT ( 'NONE', ( -0.03988517032605130158, -0.9096959278232360502, 0.8299999999999988498 ) ) ; +#54217 = LINE ( 'NONE', #25122, #5771 ) ; +#54218 = EDGE_CURVE ( 'NONE', #66963, #21841, #23856, .T. ) ; +#54220 = ORIENTED_EDGE ( 'NONE', *, *, #7732, .F. ) ; +#54219 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.500000000000000000, 1.121611168366946904E-78 ) ) ; +#54221 = SURFACE_SIDE_STYLE ('',( #6663 ) ) ; +#54222 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55085, #100380, #31567, #69849 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54224 = CARTESIAN_POINT ( 'NONE', ( 1.631872624588970089, -1.500900992704750081, 0.8100000000000000533 ) ) ; +#54223 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54225 = CARTESIAN_POINT ( 'NONE', ( -0.9735001140982717516, -1.211946142803215665, 0.8099999999998319655 ) ) ; +#54226 = PLANE ( 'NONE', #6470 ) ; +#54227 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#54228 = VERTEX_POINT ( 'NONE', #61668 ) ; +#54229 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#54230 = FILL_AREA_STYLE ('',( #55752 ) ) ; +#54231 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#54232 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146550232, 0.5686465759269649922, 0.8100000000000000533 ) ) ; +#54233 = FACE_OUTER_BOUND ( 'NONE', #85696, .T. ) ; +#54234 = STYLED_ITEM ( 'NONE', ( #9749 ), #52709 ) ; +#54236 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54235 = CARTESIAN_POINT ( 'NONE', ( 0.4673939658190879864, -1.066920424575050097, 0.8100000000000000533 ) ) ; +#54237 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#54238 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54239 = EDGE_CURVE ( 'NONE', #13197, #84465, #60401, .T. ) ; +#54240 = PRESENTATION_STYLE_ASSIGNMENT (( #77712 ) ) ; +#54241 = EDGE_CURVE ( 'NONE', #98563, #23378, #23353, .T. ) ; +#54242 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90089 ), #60738 ) ; +#54243 = VECTOR ( 'NONE', #9494, 1000.000000000000114 ) ; +#54244 = LINE ( 'NONE', #31248, #42835 ) ; +#54245 = LINE ( 'NONE', #85367, #24728 ) ; +#54246 = VERTEX_POINT ( 'NONE', #25882 ) ; +#54247 = PRESENTATION_STYLE_ASSIGNMENT (( #22588 ) ) ; +#54248 = SURFACE_SIDE_STYLE ('',( #23109 ) ) ; +#54249 = EDGE_LOOP ( 'NONE', ( #45214, #37026, #62789, #13026 ) ) ; +#54252 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54251 = LINE ( 'NONE', #23112, #11498 ) ; +#54250 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49370 ), #39594 ) ; +#54253 = FACE_OUTER_BOUND ( 'NONE', #67234, .T. ) ; +#54254 = FILL_AREA_STYLE ('',( #46564 ) ) ; +#54255 = EDGE_CURVE ( 'NONE', #15311, #690, #95770, .T. ) ; +#54256 = AXIS2_PLACEMENT_3D ( 'NONE', #36562, #20199, #59064 ) ; +#54257 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70492 ), #10126 ) ; +#54258 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#54259 = VERTEX_POINT ( 'NONE', #56023 ) ; +#54260 = CARTESIAN_POINT ( 'NONE', ( 1.799170355476140015, -0.9218577280486121017, 0.8100000000000008304 ) ) ; +#54261 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01085786437626898131, -0.1500000000000000222 ) ) ; +#54262 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#54263 = FACE_OUTER_BOUND ( 'NONE', #100773, .T. ) ; +#54264 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24928 ) ) ; +#54265 = VECTOR ( 'NONE', #94647, 1000.000000000000000 ) ; +#54266 = CARTESIAN_POINT ( 'NONE', ( 11.49435650049995239, 6.539919500499948413, 0.8991599999999999593 ) ) ; +#54267 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.1600000000000000033, 1.129999999999999893 ) ) ; +#54268 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 8.286472999999999089, 0.8991599999999999593 ) ) ; +#54270 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662329837, -1.437662337662340084, 0.8299999999999999600 ) ) ; +#54269 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8470 ) ) ; +#54272 = VECTOR ( 'NONE', #38836, 1000.000000000000114 ) ; +#54271 = LINE ( 'NONE', #8211, #24835 ) ; +#54273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20914, 'distance_accuracy_value', 'NONE'); +#54274 = CARTESIAN_POINT ( 'NONE', ( 6.084989124874956801, 10.26637212487495709, 0.8991599999999999593 ) ) ; +#54275 = ORIENTED_EDGE ( 'NONE', *, *, #20325, .T. ) ; +#54276 = FACE_OUTER_BOUND ( 'NONE', #77114, .T. ) ; +#54278 = EDGE_LOOP ( 'NONE', ( #55247, #52648, #81230, #33609 ) ) ; +#54277 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39619 ), #51024 ) ; +#54279 = LINE ( 'NONE', #58841, #40508 ) ; +#54280 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63121, 'distance_accuracy_value', 'NONE'); +#54281 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11168, 'distance_accuracy_value', 'NONE'); +#54282 = VECTOR ( 'NONE', #95274, 1000.000000000000000 ) ; +#54283 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#54284 = CARTESIAN_POINT ( 'NONE', ( 7.064730999999999206, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#54285 = CARTESIAN_POINT ( 'NONE', ( 7.386066499500000937, 9.092575499500000547, 0.8991599999999999593 ) ) ; +#54286 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54287 = PLANE ( 'NONE', #47663 ) ; +#54288 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.600000000000000089, -11.41999999999999993 ) ) ; +#54289 = FACE_BOUND ( 'NONE', #58464, .T. ) ; +#54290 = ORIENTED_EDGE ( 'NONE', *, *, #58442, .T. ) ; +#54291 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000172, 0.8991599999999999593 ) ) ; +#54292 = PRESENTATION_STYLE_ASSIGNMENT (( #93034 ) ) ; +#54293 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7170, 'distance_accuracy_value', 'NONE'); +#54294 = EDGE_LOOP ( 'NONE', ( #98336, #3305, #48332, #45243, #57603, #78513, #88942, #20711, #99938, #88843, #52543, #67479, #2968, #81684, #58264, #58745, #48928, #3481, #4337 ) ) ; +#54295 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54296 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54297 = EDGE_CURVE ( 'NONE', #60900, #100686, #73349, .T. ) ; +#54298 = ORIENTED_EDGE ( 'NONE', *, *, #70012, .T. ) ; +#54299 = EDGE_CURVE ( 'NONE', #79108, #16133, #9943, .T. ) ; +#54301 = VERTEX_POINT ( 'NONE', #81536 ) ; +#54300 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#54302 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78271, 'distance_accuracy_value', 'NONE'); +#54303 = SURFACE_SIDE_STYLE ('',( #77258 ) ) ; +#54304 = ADVANCED_FACE ( 'NONE', ( #80007 ), #18161, .T. ) ; +#54305 = ORIENTED_EDGE ( 'NONE', *, *, #50193, .T. ) ; +#54306 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#54307 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54309 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01500000000000000465, -0.1400000000000000133 ) ) ; +#54308 = AXIS2_PLACEMENT_3D ( 'NONE', #100731, #9370, #62090 ) ; +#54310 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8199999999999999512 ) ) ; +#54311 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, -3.099999999999992539, -0.02000000000000000042 ) ) ; +#54312 = ORIENTED_EDGE ( 'NONE', *, *, #78129, .T. ) ; +#54313 = EDGE_LOOP ( 'NONE', ( #36270, #91857, #66857, #83452 ) ) ; +#54314 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91747 ), #26564 ) ; +#54315 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54316 = ORIENTED_EDGE ( 'NONE', *, *, #4514, .T. ) ; +#54317 = EDGE_LOOP ( 'NONE', ( #76119, #49951, #83077, #41707 ) ) ; +#54319 = ORIENTED_EDGE ( 'NONE', *, *, #30080, .T. ) ; +#54318 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#54320 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#54323 = CARTESIAN_POINT ( 'NONE', ( -0.8193368432721279682, 0.5992714337669160507, 0.8100000000000000533 ) ) ; +#54322 = CARTESIAN_POINT ( 'NONE', ( -0.03713474025974068671, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#54321 = VECTOR ( 'NONE', #61558, 1000.000000000000000 ) ; +#54324 = VECTOR ( 'NONE', #18959, 1000.000000000000000 ) ; +#54325 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54326 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54327 = ORIENTED_EDGE ( 'NONE', *, *, #96532, .F. ) ; +#54328 = SURFACE_STYLE_USAGE ( .BOTH. , #38500 ) ; +#54330 = FACE_OUTER_BOUND ( 'NONE', #56458, .T. ) ; +#54329 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60838 ), #82268 ) ; +#54331 = FACE_OUTER_BOUND ( 'NONE', #18513, .T. ) ; +#54332 = VERTEX_POINT ( 'NONE', #17670 ) ; +#54333 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#54334 = FACE_OUTER_BOUND ( 'NONE', #1487, .T. ) ; +#54335 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56448 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6740, #59509, #20642 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54336 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95110 ) ) ; +#54337 = SURFACE_SIDE_STYLE ('',( #100651 ) ) ; +#54338 = AXIS2_PLACEMENT_3D ( 'NONE', #23363, #85638, #76461 ) ; +#54339 = ORIENTED_EDGE ( 'NONE', *, *, #34481, .T. ) ; +#54340 = FILL_AREA_STYLE_COLOUR ( '', #43679 ) ; +#54341 = VERTEX_POINT ( 'NONE', #72309 ) ; +#54342 = AXIS2_PLACEMENT_3D ( 'NONE', #9057, #48970, #96391 ) ; +#54343 = EDGE_CURVE ( 'NONE', #68202, #24985, #96279, .T. ) ; +#54344 = ADVANCED_FACE ( 'NONE', ( #49347 ), #42693, .T. ) ; +#54345 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2304 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12131, #73003, #65847 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54346 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#54348 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8099999999999013545 ) ) ; +#54349 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -11.36999999999999922 ) ) ; +#54350 = VECTOR ( 'NONE', #36269, 1000.000000000000000 ) ; +#54351 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39694 ), #83728 ) ; +#54352 = SURFACE_STYLE_USAGE ( .BOTH. , #46662 ) ; +#54353 = ADVANCED_FACE ( 'NONE', ( #92504 ), #14376, .T. ) ; +#54354 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54355 = ORIENTED_EDGE ( 'NONE', *, *, #33531, .T. ) ; +#54356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54357 = VERTEX_POINT ( 'NONE', #21576 ) ; +#54358 = SURFACE_STYLE_FILL_AREA ( #23212 ) ; +#54360 = DIRECTION ( 'NONE', ( 0.7071067806865475314, 0.7071067816865476141, 0.000000000000000000 ) ) ; +#54359 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#54361 = ADVANCED_FACE ( 'NONE', ( #60916 ), #30226, .F. ) ; +#54362 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#54363 = EDGE_CURVE ( 'NONE', #98768, #25575, #99149, .T. ) ; +#54364 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6120, 'distance_accuracy_value', 'NONE'); +#54365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8560 ), #11844 ) ; +#54366 = PRESENTATION_STYLE_ASSIGNMENT (( #21692 ) ) ; +#54368 = EDGE_CURVE ( 'NONE', #71662, #89231, #5717, .T. ) ; +#54367 = SURFACE_STYLE_USAGE ( .BOTH. , #17038 ) ; +#54369 = DIRECTION ( 'NONE', ( -0.7071060119555133694, -0.7071075504167448900, 0.000000000000000000 ) ) ; +#54370 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54371 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54372 = LINE ( 'NONE', #89030, #78862 ) ; +#54373 = CARTESIAN_POINT ( 'NONE', ( 9.535670999999998898, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#54374 = ORIENTED_EDGE ( 'NONE', *, *, #66974, .T. ) ; +#54375 = LINE ( 'NONE', #15517, #49774 ) ; +#54376 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#54378 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54377 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.266666666666647068, 0.000000000000000000 ) ) ; +#54379 = LINE ( 'NONE', #40577, #3138 ) ; +#54380 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#54381 = SURFACE_STYLE_FILL_AREA ( #77327 ) ; +#54382 = EDGE_CURVE ( 'NONE', #75772, #37735, #7678, .T. ) ; +#54383 = CARTESIAN_POINT ( 'NONE', ( -1.316306714908529907, -1.318596846191909977, 0.8299999999999998490 ) ) ; +#54384 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.099999999999999867, 0.8299999999999999600 ) ) ; +#54385 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5422 ) ) ; +#54386 = CARTESIAN_POINT ( 'NONE', ( -0.1381505133853420109, 2.561284075926970161, 0.8100000000000000533 ) ) ; +#54387 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54388 = VERTEX_POINT ( 'NONE', #97286 ) ; +#54389 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#54391 = ADVANCED_FACE ( 'NONE', ( #68019, #95523 ), #79238, .F. ) ; +#54390 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8648700000000000276 ) ) ; +#54392 = LINE ( 'NONE', #92150, #83251 ) ; +#54393 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.016666666666667052, 0.000000000000000000 ) ) ; +#54394 = CARTESIAN_POINT ( 'NONE', ( -0.04240146891761689685, -1.428263396816370046, 0.8299999999999999600 ) ) ; +#54395 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8576 ) ) ; +#54396 = SURFACE_STYLE_FILL_AREA ( #85511 ) ; +#54397 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#54398 = SURFACE_STYLE_FILL_AREA ( #23253 ) ; +#54399 = VECTOR ( 'NONE', #50541, 1000.000000000000000 ) ; +#54400 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54402 = PRESENTATION_STYLE_ASSIGNMENT (( #76861 ) ) ; +#54403 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#54404 = LINE ( 'NONE', #30365, #79889 ) ; +#54405 = ADVANCED_FACE ( 'NONE', ( #32274 ), #39405, .F. ) ; +#54406 = AXIS2_PLACEMENT_3D ( 'NONE', #70542, #47573, #9194 ) ; +#54407 = FACE_BOUND ( 'NONE', #47548, .T. ) ; +#54408 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608477551, 0.6899999999999999467, 0.4397321428571430713 ) ) ; +#54409 = ORIENTED_EDGE ( 'NONE', *, *, #78337, .F. ) ; +#54410 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12279, 'distance_accuracy_value', 'NONE'); +#54411 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#54412 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#54413 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70403 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2530, #12112, #95921 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54414 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54415 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#54416 = CARTESIAN_POINT ( 'NONE', ( -1.246499984327120059, -1.124851061273939967, 0.8100000000000000533 ) ) ; +#54417 = VERTEX_POINT ( 'NONE', #56282 ) ; +#54418 = PRODUCT_DEFINITION ( 'δ֪', '', #19273, #80039 ) ; +#54419 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999992895, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#54420 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54421 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88853, 'distance_accuracy_value', 'NONE'); +#54424 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83779 ) ) ; +#54423 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54422 = SURFACE_STYLE_FILL_AREA ( #22761 ) ; +#54425 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79615 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66788, #91280, #14131 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35966 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55538, #40206, #63197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54427 = ORIENTED_EDGE ( 'NONE', *, *, #66296, .F. ) ; +#54428 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41382 ) ) ; +#54429 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3897 ), #3676 ) ; +#54430 = STYLED_ITEM ( 'NONE', ( #53296 ), #97169 ) ; +#54431 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54432 = FACE_OUTER_BOUND ( 'NONE', #91873, .T. ) ; +#54433 = ADVANCED_FACE ( 'NONE', ( #48619 ), #87392, .T. ) ; +#54434 = LINE ( 'NONE', #6844, #29259 ) ; +#54435 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#54436 = ORIENTED_EDGE ( 'NONE', *, *, #59794, .F. ) ; +#54437 = VECTOR ( 'NONE', #37924, 1000.000000000000000 ) ; +#54438 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22774, 'distance_accuracy_value', 'NONE'); +#54439 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54440 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#54441 = EDGE_CURVE ( 'NONE', #51828, #86388, #42461, .T. ) ; +#54442 = ORIENTED_EDGE ( 'NONE', *, *, #83578, .F. ) ; +#54443 = VERTEX_POINT ( 'NONE', #3641 ) ; +#54444 = PLANE ( 'NONE', #1614 ) ; +#54445 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#54446 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54447 = ORIENTED_EDGE ( 'NONE', *, *, #22440, .T. ) ; +#54448 = SURFACE_STYLE_USAGE ( .BOTH. , #68215 ) ; +#54449 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#54450 = EDGE_CURVE ( 'NONE', #47472, #91193, #73087, .T. ) ; +#54451 = CARTESIAN_POINT ( 'NONE', ( 0.5335638015470970386, -1.143334495870530265, 0.8299999999999999600 ) ) ; +#54452 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#54453 = VECTOR ( 'NONE', #14327, 1000.000000000000000 ) ; +#54454 = PLANE ( 'NONE', #31843 ) ; +#54455 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #92560, #30289 ) ; +#54456 = EDGE_CURVE ( 'NONE', #88653, #5088, #74096, .T. ) ; +#54457 = VECTOR ( 'NONE', #39391, 1000.000000000000000 ) ; +#54458 = ORIENTED_EDGE ( 'NONE', *, *, #96536, .T. ) ; +#54459 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54461 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.000000000000000000 ) ) ; +#54460 = FILL_AREA_STYLE_COLOUR ( '', #31310 ) ; +#54463 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#54462 = VECTOR ( 'NONE', #79294, 1000.000000000000000 ) ; +#54464 = ORIENTED_EDGE ( 'NONE', *, *, #700, .T. ) ; +#54465 = PLANE ( 'NONE', #48372 ) ; +#54466 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#54467 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39726 ) ) ; +#54468 = SURFACE_STYLE_USAGE ( .BOTH. , #84570 ) ; +#54469 = EDGE_LOOP ( 'NONE', ( #38051, #91473, #8542, #6397 ) ) ; +#54470 = PRESENTATION_STYLE_ASSIGNMENT (( #28955 ) ) ; +#54471 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92169 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87928, #86938, #95557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54472 = ORIENTED_EDGE ( 'NONE', *, *, #46657, .T. ) ; +#54473 = EDGE_CURVE ( 'NONE', #48176, #13508, #68822, .T. ) ; +#54474 = ORIENTED_EDGE ( 'NONE', *, *, #15913, .F. ) ; +#54475 = EDGE_CURVE ( 'NONE', #99050, #35632, #11703, .T. ) ; +#54476 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#54477 = SURFACE_STYLE_USAGE ( .BOTH. , #23322 ) ; +#54478 = VECTOR ( 'NONE', #31376, 1000.000000000000000 ) ; +#54479 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54480 = ORIENTED_EDGE ( 'NONE', *, *, #77723, .T. ) ; +#54481 = SURFACE_STYLE_USAGE ( .BOTH. , #22302 ) ; +#54482 = FACE_OUTER_BOUND ( 'NONE', #93157, .T. ) ; +#54483 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#54484 = SURFACE_SIDE_STYLE ('',( #16631 ) ) ; +#54485 = ORIENTED_EDGE ( 'NONE', *, *, #3849, .F. ) ; +#54486 = SURFACE_STYLE_FILL_AREA ( #23333 ) ; +#54487 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#54488 = ORIENTED_EDGE ( 'NONE', *, *, #73290, .T. ) ; +#54489 = ORIENTED_EDGE ( 'NONE', *, *, #244, .F. ) ; +#54490 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#54491 = VECTOR ( 'NONE', #47728, 1000.000000000000000 ) ; +#54493 = FACE_OUTER_BOUND ( 'NONE', #8002, .T. ) ; +#54492 = CARTESIAN_POINT ( 'NONE', ( 0.9886343406507150933, -1.414598001867640065, 0.8299999999999999600 ) ) ; +#54494 = SURFACE_STYLE_USAGE ( .BOTH. , #87629 ) ; +#54495 = ADVANCED_FACE ( 'NONE', ( #51128 ), #18947, .T. ) ; +#54496 = FACE_OUTER_BOUND ( 'NONE', #3562, .T. ) ; +#54497 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#54498 = ADVANCED_FACE ( 'NONE', ( #82269 ), #12220, .T. ) ; +#54499 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44676 ) ) ; +#54500 = LINE ( 'NONE', #85107, #5837 ) ; +#54501 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54502 = ADVANCED_FACE ( 'NONE', ( #5109 ), #29140, .T. ) ; +#54503 = STYLED_ITEM ( 'NONE', ( #73828 ), #60964 ) ; +#54504 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54505 = SURFACE_SIDE_STYLE ('',( #23347 ) ) ; +#54506 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#54507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34983 ) ) ; +#54508 = EDGE_LOOP ( 'NONE', ( #3360, #57185, #4467, #74914 ) ) ; +#54509 = PRESENTATION_STYLE_ASSIGNMENT (( #30457 ) ) ; +#54510 = LINE ( 'NONE', #86633, #4862 ) ; +#54511 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75690 ), #11984 ) ; +#54512 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#54513 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.82000000000000028 ) ) ; +#54514 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16087 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12825, #58909, #50735 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54515 = LINE ( 'NONE', #53497, #54933 ) ; +#54516 = SURFACE_STYLE_FILL_AREA ( #15651 ) ; +#54517 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#54518 = ORIENTED_EDGE ( 'NONE', *, *, #88230, .T. ) ; +#54520 = EDGE_CURVE ( 'NONE', #66504, #41349, #85757, .T. ) ; +#54519 = SURFACE_STYLE_USAGE ( .BOTH. , #80016 ) ; +#54521 = FILL_AREA_STYLE_COLOUR ( '', #70096 ) ; +#54522 = CARTESIAN_POINT ( 'NONE', ( 0.9399999999999999467, 1.827097501072570334E-17, 0.3499999999999999223 ) ) ; +#54523 = PLANE ( 'NONE', #54338 ) ; +#54524 = SURFACE_SIDE_STYLE ('',( #45291 ) ) ; +#54525 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20889, 'distance_accuracy_value', 'NONE'); +#54526 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20237 ), #74047 ) ; +#54527 = FACE_OUTER_BOUND ( 'NONE', #17893, .T. ) ; +#54528 = FACE_OUTER_BOUND ( 'NONE', #64758, .T. ) ; +#54529 = EDGE_CURVE ( 'NONE', #41527, #80241, #67417, .T. ) ; +#54530 = DIRECTION ( 'NONE', ( -0.7071075504167422254, -0.7071060119555159229, 0.000000000000000000 ) ) ; +#54531 = CARTESIAN_POINT ( 'NONE', ( -0.1311282467532469964, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#54532 = LINE ( 'NONE', #46306, #71647 ) ; +#54533 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54534 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46307 ) ) ; +#54535 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#54536 = FILL_AREA_STYLE_COLOUR ( '', #25211 ) ; +#54537 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#54538 = AXIS2_PLACEMENT_3D ( 'NONE', #1628, #71572, #87375 ) ; +#54539 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #48931, 'design' ) ; +#54540 = PLANE ( 'NONE', #82763 ) ; +#54541 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.4245906043549200204, -0.02000000000000000042 ) ) ; +#54542 = FILL_AREA_STYLE ('',( #86670 ) ) ; +#54543 = EDGE_LOOP ( 'NONE', ( #20238, #80113, #42513, #50827 ) ) ; +#54544 = PRESENTATION_STYLE_ASSIGNMENT (( #55047 ) ) ; +#54545 = CARTESIAN_POINT ( 'NONE', ( 1.566818635346699962, -1.328064047174219997, 0.8299999999999977396 ) ) ; +#54547 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#54546 = STYLED_ITEM ( 'NONE', ( #40955 ), #88536 ) ; +#54548 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31729, 'distance_accuracy_value', 'NONE'); +#54549 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#54550 = LINE ( 'NONE', #93286, #41658 ) ; +#54552 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23764 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26051, #41363, #26547 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54551 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8099999999999815126 ) ) ; +#54553 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88611, #18647, #64143, #95228 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54554 = LINE ( 'NONE', #22368, #79261 ) ; +#54555 = EDGE_CURVE ( 'NONE', #78767, #65764, #75590, .T. ) ; +#54556 = STYLED_ITEM ( 'NONE', ( #33087 ), #76904 ) ; +#54557 = ORIENTED_EDGE ( 'NONE', *, *, #81336, .F. ) ; +#54558 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#54559 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666633301, -1.899999999999999911, 3.495651678169922342E-76 ) ) ; +#54560 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886600000000008, 0.8648700000000000276 ) ) ; +#54561 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1524, 'distance_accuracy_value', 'NONE'); +#54562 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4028 ), #33425 ) ; +#54563 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34752, #88849, #65352, #96475 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54564 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34239, 'distance_accuracy_value', 'NONE'); +#54565 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #33171, #34291 ) ; +#54566 = FILL_AREA_STYLE_COLOUR ( '', #38712 ) ; +#54567 = EDGE_CURVE ( 'NONE', #78426, #12278, #22217, .T. ) ; +#54568 = MANIFOLD_SOLID_BREP ( 'ÊäÈë60', #4380 ) ; +#54569 = EDGE_LOOP ( 'NONE', ( #18170, #15058, #60334, #760 ) ) ; +#54570 = ORIENTED_EDGE ( 'NONE', *, *, #29924, .F. ) ; +#54572 = STYLED_ITEM ( 'NONE', ( #41314 ), #27179 ) ; +#54571 = STYLED_ITEM ( 'NONE', ( #10908 ), #38329 ) ; +#54573 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92067 ) ) ; +#54574 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#54575 = VERTEX_POINT ( 'NONE', #22468 ) ; +#54576 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54577 = EDGE_CURVE ( 'NONE', #10657, #17377, #69399, .T. ) ; +#54579 = SURFACE_SIDE_STYLE ('',( #99880 ) ) ; +#54578 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34981 ), #15370 ) ; +#54580 = FILL_AREA_STYLE ('',( #7989 ) ) ; +#54581 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65952, 'distance_accuracy_value', 'NONE'); +#54582 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #1952 ) ; +#54583 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#54584 = PRESENTATION_STYLE_ASSIGNMENT (( #77024 ) ) ; +#54586 = EDGE_LOOP ( 'NONE', ( #1729, #24924, #36507, #47788 ) ) ; +#54585 = ORIENTED_EDGE ( 'NONE', *, *, #3117, .F. ) ; +#54587 = ADVANCED_FACE ( 'NONE', ( #84751 ), #7057, .T. ) ; +#54588 = EDGE_LOOP ( 'NONE', ( #11126, #54275, #86337, #88339 ) ) ; +#54589 = FACE_OUTER_BOUND ( 'NONE', #55597, .T. ) ; +#54590 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54592 = SURFACE_STYLE_USAGE ( .BOTH. , #62747 ) ; +#54591 = SURFACE_SIDE_STYLE ('',( #23422 ) ) ; +#54593 = ORIENTED_EDGE ( 'NONE', *, *, #24064, .T. ) ; +#54594 = EDGE_CURVE ( 'NONE', #33000, #46763, #87378, .T. ) ; +#54595 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54596 = LINE ( 'NONE', #65122, #34048 ) ; +#54597 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36667 ), #49726 ) ; +#54598 = ORIENTED_EDGE ( 'NONE', *, *, #79123, .F. ) ; +#54599 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18298, #998, #72964, #32152 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54600 = SURFACE_SIDE_STYLE ('',( #69345 ) ) ; +#54601 = ORIENTED_EDGE ( 'NONE', *, *, #90537, .F. ) ; +#54602 = EDGE_CURVE ( 'NONE', #28432, #72535, #47463, .T. ) ; +#54603 = ORIENTED_EDGE ( 'NONE', *, *, #81795, .F. ) ; +#54604 = EDGE_CURVE ( 'NONE', #74888, #61666, #487, .T. ) ; +#54605 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54606 = FACE_OUTER_BOUND ( 'NONE', #73900, .T. ) ; +#54607 = AXIS2_PLACEMENT_3D ( 'NONE', #8306, #61546, #62046 ) ; +#54608 = FILL_AREA_STYLE ('',( #79082 ) ) ; +#54611 = ADVANCED_FACE ( 'NONE', ( #38800 ), #2016, .T. ) ; +#54610 = ORIENTED_EDGE ( 'NONE', *, *, #6374, .F. ) ; +#54609 = FACE_OUTER_BOUND ( 'NONE', #17741, .T. ) ; +#54612 = EDGE_CURVE ( 'NONE', #75525, #75369, #16284, .T. ) ; +#54613 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54614 = FILL_AREA_STYLE_COLOUR ( '', #28666 ) ; +#54615 = STYLED_ITEM ( 'NONE', ( #14913 ), #89822 ) ; +#54616 = CARTESIAN_POINT ( 'NONE', ( 11.23272687512504575, 4.807507875125044627, 0.8991599999999999593 ) ) ; +#54617 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54618 = ORIENTED_EDGE ( 'NONE', *, *, #51558, .T. ) ; +#54619 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#54620 = PRESENTATION_STYLE_ASSIGNMENT (( #70392 ) ) ; +#54621 = ORIENTED_EDGE ( 'NONE', *, *, #87563, .F. ) ; +#54622 = VERTEX_POINT ( 'NONE', #70955 ) ; +#54623 = LINE ( 'NONE', #25995, #82950 ) ; +#54624 = CARTESIAN_POINT ( 'NONE', ( 1.697893922398610034, -1.445363849546990043, 0.8300000000000002931 ) ) ; +#54625 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59533 ), #7194 ) ; +#54626 = EDGE_CURVE ( 'NONE', #18909, #54417, #1004, .T. ) ; +#54627 = FILL_AREA_STYLE_COLOUR ( '', #48263 ) ; +#54628 = EDGE_CURVE ( 'NONE', #46588, #16846, #25517, .T. ) ; +#54629 = FILL_AREA_STYLE ('',( #23464 ) ) ; +#54630 = VERTEX_POINT ( 'NONE', #55659 ) ; +#54631 = AXIS2_PLACEMENT_3D ( 'NONE', #29200, #37379, #70496 ) ; +#54632 = ORIENTED_EDGE ( 'NONE', *, *, #51238, .T. ) ; +#54633 = PLANE ( 'NONE', #22745 ) ; +#54634 = PRESENTATION_STYLE_ASSIGNMENT (( #32651 ) ) ; +#54635 = PLANE ( 'NONE', #43155 ) ; +#54636 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95315 ) ) ; +#54637 = SURFACE_STYLE_USAGE ( .BOTH. , #78097 ) ; +#54639 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62801 ) ) ; +#54638 = CARTESIAN_POINT ( 'NONE', ( 1.792693045999540047, -1.018845982455530041, 0.8100000000000000533 ) ) ; +#54640 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#54641 = VECTOR ( 'NONE', #94253, 1000.000000000000000 ) ; +#54642 = SURFACE_STYLE_FILL_AREA ( #75222 ) ; +#54643 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54644 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#54645 = PRESENTATION_STYLE_ASSIGNMENT (( #67520 ) ) ; +#54646 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54647 = SURFACE_SIDE_STYLE ('',( #93381 ) ) ; +#54648 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54650 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54649 = FILL_AREA_STYLE_COLOUR ( '', #13031 ) ; +#54651 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54652 = CARTESIAN_POINT ( 'NONE', ( 4.171940352103389200E-17, 0.2500000001077751222, 0.2299999998740531737 ) ) ; +#54653 = EDGE_CURVE ( 'NONE', #58234, #7394, #51016, .T. ) ; +#54654 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#54655 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54656 = LINE ( 'NONE', #85755, #10267 ) ; +#54657 = VECTOR ( 'NONE', #83929, 1000.000000000000114 ) ; +#54659 = ADVANCED_FACE ( 'NONE', ( #65818 ), #35695, .T. ) ; +#54658 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64814, 'distance_accuracy_value', 'NONE'); +#54660 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #72077, #80757, #95009, #79223 ), + ( #25141, #49108, #33787, #2134 ), + ( #39919, #3130, #80252, #48609 ), + ( #24639, #9193, #79753, #40438 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.3333333333333334259, 0.3333333333333334259, 1.000000000000000000), + ( 0.8047378541243649375, 0.2682459513747884050, 0.2682459513747884050, 0.8047378541243649375), + ( 0.8047378541243649375, 0.2682459513747884050, 0.2682459513747884050, 0.8047378541243649375), + ( 1.000000000000000000, 0.3333333333333334259, 0.3333333333333334259, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#54661 = ORIENTED_EDGE ( 'NONE', *, *, #21468, .F. ) ; +#54662 = SURFACE_STYLE_USAGE ( .BOTH. , #7068 ) ; +#54663 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54664 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54665 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54666 = SURFACE_STYLE_FILL_AREA ( #85265 ) ; +#54667 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #122 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74781, #22146, #35997 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54668 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54669 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#54670 = VECTOR ( 'NONE', #77689, 1000.000000000000000 ) ; +#54671 = ORIENTED_EDGE ( 'NONE', *, *, #20345, .F. ) ; +#54673 = EDGE_CURVE ( 'NONE', #35498, #56849, #88792, .T. ) ; +#54672 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85619 ) ) ; +#54674 = VERTEX_POINT ( 'NONE', #72448 ) ; +#54675 = FACE_OUTER_BOUND ( 'NONE', #24830, .T. ) ; +#54676 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54678 = LINE ( 'NONE', #71999, #90115 ) ; +#54679 = PRESENTATION_STYLE_ASSIGNMENT (( #7592 ) ) ; +#54680 = AXIS2_PLACEMENT_3D ( 'NONE', #100592, #92535, #69041 ) ; +#54681 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54682 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54683 = FILL_AREA_STYLE ('',( #38341 ) ) ; +#54684 = ORIENTED_EDGE ( 'NONE', *, *, #37338, .T. ) ; +#54685 = LINE ( 'NONE', #1043, #14169 ) ; +#54686 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1350000000000000089 ) ) ; +#54687 = ORIENTED_EDGE ( 'NONE', *, *, #85029, .T. ) ; +#54688 = FILL_AREA_STYLE_COLOUR ( '', #44178 ) ; +#54689 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4544 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13174, #5553, #52574 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54690 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#54691 = ORIENTED_EDGE ( 'NONE', *, *, #66929, .T. ) ; +#54692 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98592 ), #18796 ) ; +#54694 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54693 = SURFACE_STYLE_USAGE ( .BOTH. , #528 ) ; +#54695 = CARTESIAN_POINT ( 'NONE', ( 1.178090748447750080, -1.443574297695930264, 0.8100000000000000533 ) ) ; +#54696 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146561808, 0.2541340759269652416, 0.8299999999999999600 ) ) ; +#54697 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#54698 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54699 = CARTESIAN_POINT ( 'NONE', ( 1.810920360744870061, -1.177156496261070107, 0.8299999999999999600 ) ) ; +#54700 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43387, #74038, #12684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54701 = LINE ( 'NONE', #30163, #49622 ) ; +#54703 = VERTEX_POINT ( 'NONE', #18306 ) ; +#54702 = ORIENTED_EDGE ( 'NONE', *, *, #59556, .F. ) ; +#54704 = ADVANCED_FACE ( 'NONE', ( #88292 ), #58684, .T. ) ; +#54705 = FILL_AREA_STYLE_COLOUR ( '', #55398 ) ; +#54706 = VERTEX_POINT ( 'NONE', #19334 ) ; +#54707 = SURFACE_STYLE_USAGE ( .BOTH. , #8624 ) ; +#54708 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26496 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52159, #67925, #73617 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54709 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56333 ), #12181 ) ; +#54710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54711 = ORIENTED_EDGE ( 'NONE', *, *, #17596, .F. ) ; +#54712 = EDGE_CURVE ( 'NONE', #41605, #47027, #66317, .T. ) ; +#54713 = VERTEX_POINT ( 'NONE', #42833 ) ; +#54715 = VECTOR ( 'NONE', #91869, 1000.000000000000000 ) ; +#54714 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#54717 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54716 = FILL_AREA_STYLE ('',( #15341 ) ) ; +#54718 = LINE ( 'NONE', #61381, #77448 ) ; +#54719 = VERTEX_POINT ( 'NONE', #49496 ) ; +#54720 = ORIENTED_EDGE ( 'NONE', *, *, #11353, .F. ) ; +#54721 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54722 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23972 ) ) ; +#54723 = VERTEX_POINT ( 'NONE', #33680 ) ; +#54724 = EDGE_CURVE ( 'NONE', #62242, #16362, #35199, .T. ) ; +#54725 = STYLED_ITEM ( 'NONE', ( #97648 ), #98170 ) ; +#54726 = ADVANCED_FACE ( 'NONE', ( #84637 ), #52323, .F. ) ; +#54727 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54728 = AXIS2_PLACEMENT_3D ( 'NONE', #59894, #4708, #12300 ) ; +#54731 = EDGE_CURVE ( 'NONE', #59760, #41056, #13611, .T. ) ; +#54730 = ORIENTED_EDGE ( 'NONE', *, *, #40048, .T. ) ; +#54729 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#54732 = EDGE_CURVE ( 'NONE', #26946, #18237, #5965, .T. ) ; +#54733 = VECTOR ( 'NONE', #95841, 1000.000000000000000 ) ; +#54734 = SURFACE_SIDE_STYLE ('',( #16363 ) ) ; +#54735 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#54736 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#54737 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54738 = ORIENTED_EDGE ( 'NONE', *, *, #91056, .F. ) ; +#54739 = SURFACE_STYLE_FILL_AREA ( #33252 ) ; +#54740 = SURFACE_STYLE_USAGE ( .BOTH. , #67 ) ; +#54741 = ORIENTED_EDGE ( 'NONE', *, *, #56987, .T. ) ; +#54742 = MANIFOLD_SOLID_BREP ( 'ÊäÈë92', #15950 ) ; +#54743 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19038, #96129, #41548, #26737, #71674, #88503, #49210, #64523, #32876, #64017, #3234 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.017691337436107015E-05, 3.952423233967897973E-05, 5.875382848037802210E-05, 7.832621165737556769E-05, 9.793198170667367041E-05, 0.0001172428034372773606, 0.0001365502000149599292, 0.0001561259619804737544 ), + .UNSPECIFIED. ) ; +#54744 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#54745 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#54746 = ADVANCED_FACE ( 'NONE', ( #56040 ), #46818, .T. ) ; +#54748 = VERTEX_POINT ( 'NONE', #47340 ) ; +#54747 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.433333333333333570, 0.000000000000000000 ) ) ; +#54749 = EDGE_CURVE ( 'NONE', #59417, #84314, #38675, .T. ) ; +#54750 = LINE ( 'NONE', #45013, #47465 ) ; +#54751 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#54752 = PRESENTATION_STYLE_ASSIGNMENT (( #19306 ) ) ; +#54753 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61420, #53729, #100557, #7675 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54754 = LINE ( 'NONE', #38903, #42556 ) ; +#54755 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23760 ), #7331 ) ; +#54756 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#54758 = CARTESIAN_POINT ( 'NONE', ( 1.803030467297160211, -1.264112177694660000, 0.8099999999999996092 ) ) ; +#54757 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#54759 = EDGE_LOOP ( 'NONE', ( #89722, #4031, #47533, #65094 ) ) ; +#54760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54761 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54762 = VECTOR ( 'NONE', #12063, 1000.000000000000000 ) ; +#54763 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54764 = AXIS2_PLACEMENT_3D ( 'NONE', #53733, #75704, #84854 ) ; +#54765 = FILL_AREA_STYLE ('',( #50746 ) ) ; +#54767 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#54766 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#54768 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54769 = FILL_AREA_STYLE_COLOUR ( '', #67880 ) ; +#54771 = STYLED_ITEM ( 'NONE', ( #22276 ), #49425 ) ; +#54770 = PRESENTATION_STYLE_ASSIGNMENT (( #84848 ) ) ; +#54772 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71064 ), #62927 ) ; +#54773 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54774 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -1.100000000000000089, 3.495651678169978796E-76 ) ) ; +#54775 = AXIS2_PLACEMENT_3D ( 'NONE', #95362, #24981, #56117 ) ; +#54776 = VERTEX_POINT ( 'NONE', #79514 ) ; +#54777 = AXIS2_PLACEMENT_3D ( 'NONE', #11389, #20630, #97696 ) ; +#54778 = FILL_AREA_STYLE ('',( #9204 ) ) ; +#54779 = ORIENTED_EDGE ( 'NONE', *, *, #37377, .F. ) ; +#54781 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8991599999999999593 ) ) ; +#54780 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79926 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78056, #77038, #62750 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54783 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54782 = SURFACE_SIDE_STYLE ('',( #30232 ) ) ; +#54784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54785 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54786 = AXIS2_PLACEMENT_3D ( 'NONE', #50050, #9611, #88319 ) ; +#54787 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.005000000000000009645, -0.2400000000000000189 ) ) ; +#54788 = EDGE_LOOP ( 'NONE', ( #52845, #90753, #27362, #11924, #52098 ) ) ; +#54789 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54790 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#54791 = FILL_AREA_STYLE_COLOUR ( '', #24613 ) ; +#54792 = VECTOR ( 'NONE', #61142, 1000.000000000000000 ) ; +#54793 = PRESENTATION_STYLE_ASSIGNMENT (( #62951 ) ) ; +#54794 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54795 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54796 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#54797 = FILL_AREA_STYLE ('',( #23620 ) ) ; +#54798 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54799 = SURFACE_STYLE_USAGE ( .BOTH. , #16418 ) ; +#54800 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87346 ), #38446 ) ; +#54801 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220025313, -2.499999999999999556, 0.000000000000000000 ) ) ; +#54802 = AXIS2_PLACEMENT_3D ( 'NONE', #82218, #11159, #2592 ) ; +#54803 = FACE_OUTER_BOUND ( 'NONE', #24867, .T. ) ; +#54804 = ORIENTED_EDGE ( 'NONE', *, *, #44576, .F. ) ; +#54805 = LINE ( 'NONE', #93528, #74222 ) ; +#54806 = EDGE_LOOP ( 'NONE', ( #65372, #67258, #50378, #51472 ) ) ; +#54807 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54808 = SURFACE_SIDE_STYLE ('',( #87929 ) ) ; +#54809 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98705 ) ) ; +#54810 = PRESENTATION_STYLE_ASSIGNMENT (( #39968 ) ) ; +#54811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54812 = ORIENTED_EDGE ( 'NONE', *, *, #23836, .F. ) ; +#54813 = SURFACE_STYLE_FILL_AREA ( #41002 ) ; +#54814 = ORIENTED_EDGE ( 'NONE', *, *, #56537, .F. ) ; +#54815 = PRESENTATION_STYLE_ASSIGNMENT (( #100608 ) ) ; +#54816 = EDGE_LOOP ( 'NONE', ( #62382, #16810, #75866, #30311, #80465, #74257, #14197, #32096, #89871, #42699, #16478, #54316, #40938, #13196, #89266, #38760, #71233, #49024, #81074, #39257, #18519, #25934, #82436, #8487, #68573, #99301, #47515, #14121, #34719, #70394, #64280, #24808, #76044, #51573, #42997, #933 ) ) ; +#54817 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54818 = VECTOR ( 'NONE', #22837, 1000.000000000000000 ) ; +#54819 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54820 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98724 ), #79289 ) ; +#54821 = ORIENTED_EDGE ( 'NONE', *, *, #44083, .T. ) ; +#54822 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54823 = AXIS2_PLACEMENT_3D ( 'NONE', #2548, #56705, #17845 ) ; +#54824 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98733 ), #4298 ) ; +#54825 = EDGE_CURVE ( 'NONE', #3674, #25443, #34714, .T. ) ; +#54826 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15630 ) ) ; +#54827 = VECTOR ( 'NONE', #92, 1000.000000000000000 ) ; +#54828 = ORIENTED_EDGE ( 'NONE', *, *, #83223, .T. ) ; +#54829 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54830 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#54831 = FACE_OUTER_BOUND ( 'NONE', #27863, .T. ) ; +#54832 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54833 = STYLED_ITEM ( 'NONE', ( #41384 ), #48872 ) ; +#54834 = EDGE_LOOP ( 'NONE', ( #2268, #68942, #80468, #32089 ) ) ; +#54835 = EDGE_LOOP ( 'NONE', ( #21259, #80935, #80056, #31571 ) ) ; +#54836 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#54837 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100955 ) ; +#54838 = VERTEX_POINT ( 'NONE', #63201 ) ; +#54839 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23867 ) ) ; +#54840 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #87799, #6358, #46189, #85530 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54841 = ORIENTED_EDGE ( 'NONE', *, *, #83391, .T. ) ; +#54843 = VERTEX_POINT ( 'NONE', #92760 ) ; +#54842 = CARTESIAN_POINT ( 'NONE', ( 3.256562750249976101, 5.090350750249974077, 0.8991599999999999593 ) ) ; +#54844 = EDGE_CURVE ( 'NONE', #28438, #93216, #69796, .T. ) ; +#54845 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#54847 = LINE ( 'NONE', #70639, #49780 ) ; +#54846 = LINE ( 'NONE', #45595, #13381 ) ; +#54848 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#54849 = VERTEX_POINT ( 'NONE', #7941 ) ; +#54850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54851 = CARTESIAN_POINT ( 'NONE', ( 1.706409873422509937, -1.445184491613220157, 0.8099999999999997202 ) ) ; +#54852 = ORIENTED_EDGE ( 'NONE', *, *, #67912, .T. ) ; +#54853 = LINE ( 'NONE', #32869, #13860 ) ; +#54854 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3168 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38634, #31989, #15101 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54855 = FILL_AREA_STYLE ('',( #85968 ) ) ; +#54856 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58161 ) ) ; +#54857 = PLANE ( 'NONE', #31712 ) ; +#54858 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54859 = ORIENTED_EDGE ( 'NONE', *, *, #79095, .F. ) ; +#54861 = FILL_AREA_STYLE_COLOUR ( '', #4580 ) ; +#54860 = LINE ( 'NONE', #17518, #78182 ) ; +#54862 = VERTEX_POINT ( 'NONE', #39173 ) ; +#54863 = EDGE_CURVE ( 'NONE', #1018, #73618, #48424, .T. ) ; +#54864 = VECTOR ( 'NONE', #69339, 1000.000000000000000 ) ; +#54866 = PLANE ( 'NONE', #59633 ) ; +#54865 = SURFACE_STYLE_FILL_AREA ( #7286 ) ; +#54867 = PRESENTATION_STYLE_ASSIGNMENT (( #23708 ) ) ; +#54868 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14724 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64636, #33515, #95738 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54869 = CARTESIAN_POINT ( 'NONE', ( 5.646583124875012238, 9.827965875124986539, 0.8991599999999999593 ) ) ; +#54870 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48400 ) ) ; +#54871 = VERTEX_POINT ( 'NONE', #55543 ) ; +#54872 = LINE ( 'NONE', #94110, #13928 ) ; +#54873 = EDGE_LOOP ( 'NONE', ( #9170, #65600, #67939, #82803 ) ) ; +#54874 = PRESENTATION_STYLE_ASSIGNMENT (( #92606 ) ) ; +#54876 = FACE_OUTER_BOUND ( 'NONE', #93512, .T. ) ; +#54875 = SURFACE_STYLE_USAGE ( .BOTH. , #41066 ) ; +#54877 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54878 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#54879 = FILL_AREA_STYLE_COLOUR ( '', #86776 ) ; +#54880 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8100000000000000533 ) ) ; +#54881 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#54882 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -7.363535408886330351E-13 ) ) ; +#54883 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#54884 = LINE ( 'NONE', #55891, #82098 ) ; +#54885 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000000104, 0.2399999999999999911 ) ) ; +#54886 = PLANE ( 'NONE', #97198 ) ; +#54887 = VERTEX_POINT ( 'NONE', #17192 ) ; +#54888 = EDGE_CURVE ( 'NONE', #85412, #84546, #20021, .T. ) ; +#54889 = DIRECTION ( 'NONE', ( -0.7071067811865479058, -0.7071067811865472397, 0.000000000000000000 ) ) ; +#54891 = VECTOR ( 'NONE', #79757, 1000.000000000000114 ) ; +#54890 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -1.099999999999999867, 0.8299999999999999600 ) ) ; +#54893 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54892 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#54894 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#54895 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54095, 'distance_accuracy_value', 'NONE'); +#54896 = CARTESIAN_POINT ( 'NONE', ( -0.1429571421083520033, -1.443372874996269983, 0.8299999999999999600 ) ) ; +#54897 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#54898 = STYLED_ITEM ( 'NONE', ( #56896 ), #83774 ) ; +#54899 = STYLED_ITEM ( 'NONE', ( #96654 ), #90610 ) ; +#54900 = FILL_AREA_STYLE_COLOUR ( '', #9339 ) ; +#54901 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#54902 = EDGE_CURVE ( 'NONE', #6530, #1299, #95584, .T. ) ; +#54903 = ORIENTED_EDGE ( 'NONE', *, *, #31750, .F. ) ; +#54904 = MANIFOLD_SOLID_BREP ( 'ÊäÈë184', #14319 ) ; +#54905 = VECTOR ( 'NONE', #24530, 1000.000000000000000 ) ; +#54906 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#54907 = PLANE ( 'NONE', #73418 ) ; +#54908 = PRESENTATION_STYLE_ASSIGNMENT (( #31389 ) ) ; +#54909 = SURFACE_SIDE_STYLE ('',( #94152 ) ) ; +#54910 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8299999999999999600 ) ) ; +#54911 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98811 ) ) ; +#54912 = FILL_AREA_STYLE ('',( #85513 ) ) ; +#54913 = PLANE ( 'NONE', #92516 ) ; +#54914 = SURFACE_SIDE_STYLE ('',( #15541 ) ) ; +#54915 = PRESENTATION_STYLE_ASSIGNMENT (( #756 ) ) ; +#54916 = FILL_AREA_STYLE_COLOUR ( '', #83332 ) ; +#54917 = AXIS2_PLACEMENT_3D ( 'NONE', #95329, #24954, #33604 ) ; +#54918 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#54919 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#54920 = VECTOR ( 'NONE', #65170, 1000.000000000000000 ) ; +#54921 = DIRECTION ( 'NONE', ( 0.3387340427540269649, -0.000000000000000000, 0.9408821649279537347 ) ) ; +#54922 = VERTEX_POINT ( 'NONE', #34065 ) ; +#54923 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#54924 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#54926 = STYLED_ITEM ( 'NONE', ( #74265 ), #16063 ) ; +#54925 = FILL_AREA_STYLE_COLOUR ( '', #33200 ) ; +#54927 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54928 = SURFACE_STYLE_USAGE ( .BOTH. , #87059 ) ; +#54929 = CARTESIAN_POINT ( 'NONE', ( -1.067393514141900202, -1.172828961844079920, 0.8299999999999999600 ) ) ; +#54930 = ORIENTED_EDGE ( 'NONE', *, *, #15275, .F. ) ; +#54931 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54932 = LINE ( 'NONE', #16072, #20906 ) ; +#54933 = VECTOR ( 'NONE', #55018, 1000.000000000000000 ) ; +#54934 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44134, #90094, #45111, #27852 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#54935 = VECTOR ( 'NONE', #48651, 1000.000000000000000 ) ; +#54936 = LINE ( 'NONE', #92662, #87839 ) ; +#54937 = VERTEX_POINT ( 'NONE', #34576 ) ; +#54938 = ADVANCED_FACE ( 'NONE', ( #33565 ), #19727, .T. ) ; +#54939 = STYLED_ITEM ( 'NONE', ( #65456 ), #5455 ) ; +#54940 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72857 ) ) ; +#54941 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54942 = LINE ( 'NONE', #48799, #36504 ) ; +#54943 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51669 ) ) ; +#54944 = ORIENTED_EDGE ( 'NONE', *, *, #5314, .F. ) ; +#54945 = FACE_OUTER_BOUND ( 'NONE', #16438, .T. ) ; +#54946 = STYLED_ITEM ( 'NONE', ( #8633 ), #13528 ) ; +#54947 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52347, 'distance_accuracy_value', 'NONE'); +#54948 = PLANE ( 'NONE', #60548 ) ; +#54949 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54950 = EDGE_CURVE ( 'NONE', #66295, #69070, #84320, .T. ) ; +#54951 = ORIENTED_EDGE ( 'NONE', *, *, #10092, .T. ) ; +#54952 = CARTESIAN_POINT ( 'NONE', ( 8.093172875124999166, 4.142827124874999711, 0.8991599999999999593 ) ) ; +#54953 = ORIENTED_EDGE ( 'NONE', *, *, #19473, .T. ) ; +#54954 = FACE_OUTER_BOUND ( 'NONE', #75096, .T. ) ; +#54955 = FILL_AREA_STYLE_COLOUR ( '', #37328 ) ; +#54956 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#54957 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54958 = CARTESIAN_POINT ( 'NONE', ( 0.2454021686453040363, -1.061343041336519910, 0.8100000000000000533 ) ) ; +#54959 = ORIENTED_EDGE ( 'NONE', *, *, #2525, .F. ) ; +#54960 = PRESENTATION_STYLE_ASSIGNMENT (( #62131 ) ) ; +#54961 = ADVANCED_FACE ( 'NONE', ( #50412 ), #96797, .T. ) ; +#54962 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23999 ) ) ; +#54963 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99937, 'distance_accuracy_value', 'NONE'); +#54964 = CARTESIAN_POINT ( 'NONE', ( 5.802146875124987169, 2.544766875124987227, 0.8991599999999999593 ) ) ; +#54966 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, 0.000000000000000000 ) ) ; +#54965 = SURFACE_STYLE_USAGE ( .BOTH. , #30953 ) ; +#54967 = PLANE ( 'NONE', #5595 ) ; +#54968 = VERTEX_POINT ( 'NONE', #98255 ) ; +#54969 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10443, #48877, #95790 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54970 = CARTESIAN_POINT ( 'NONE', ( -0.8116130133853436401, 1.464409075926969894, 0.8100000000000000533 ) ) ; +#54971 = SURFACE_STYLE_USAGE ( .BOTH. , #10392 ) ; +#54972 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#54973 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54974 = VERTEX_POINT ( 'NONE', #36069 ) ; +#54975 = VECTOR ( 'NONE', #14863, 1000.000000000000000 ) ; +#54977 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54976 = LINE ( 'NONE', #31471, #91146 ) ; +#54978 = ORIENTED_EDGE ( 'NONE', *, *, #69716, .T. ) ; +#54979 = ORIENTED_EDGE ( 'NONE', *, *, #57796, .F. ) ; +#54980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#54981 = EDGE_CURVE ( 'NONE', #61177, #28196, #90679, .T. ) ; +#54983 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#54982 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#54984 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#54985 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80501 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26573, #41396, #97475 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#54986 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89156 ) ) ; +#54987 = FACE_OUTER_BOUND ( 'NONE', #82229, .T. ) ; +#54988 = ORIENTED_EDGE ( 'NONE', *, *, #36648, .F. ) ; +#54989 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#54990 = AXIS2_PLACEMENT_3D ( 'NONE', #47862, #79519, #33570 ) ; +#54991 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82745 ), #81090 ) ; +#54992 = ORIENTED_EDGE ( 'NONE', *, *, #28120, .T. ) ; +#54995 = LINE ( 'NONE', #78448, #30600 ) ; +#54994 = AXIS2_PLACEMENT_3D ( 'NONE', #8102, #39323, #70467 ) ; +#54993 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#54996 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#54997 = VERTEX_POINT ( 'NONE', #13485 ) ; +#54998 = ORIENTED_EDGE ( 'NONE', *, *, #64917, .F. ) ; +#54999 = CLOSED_SHELL ( 'NONE', ( #100496, #44164, #19881, #75080, #48563, #92932 ) ) ; +#55000 = CARTESIAN_POINT ( 'NONE', ( 0.9689116169396260192, -1.374349516767729984, 0.8100000000000000533 ) ) ; +#55001 = PLANE ( 'NONE', #1224 ) ; +#55002 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55003 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55311 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #736, #31893, #78853 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55004 = LINE ( 'NONE', #100802, #4286 ) ; +#55005 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8648700000000000276 ) ) ; +#55006 = VECTOR ( 'NONE', #9128, 1000.000000000000000 ) ; +#55007 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55008 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55009 = STYLED_ITEM ( 'NONE', ( #78075 ), #14782 ) ; +#55010 = VERTEX_POINT ( 'NONE', #36574 ) ; +#55011 = EDGE_CURVE ( 'NONE', #34867, #20127, #84507, .T. ) ; +#55012 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4600000000000000200, -0.2250000000000000333 ) ) ; +#55014 = CARTESIAN_POINT ( 'NONE', ( -0.7991633060742736605, 1.892060340254192008, 0.8299999999999999600 ) ) ; +#55013 = SURFACE_STYLE_USAGE ( .BOTH. , #16150 ) ; +#55015 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#55016 = FILL_AREA_STYLE ('',( #25387 ) ) ; +#55017 = CARTESIAN_POINT ( 'NONE', ( 7.064730999999999206, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#55018 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55019 = LINE ( 'NONE', #86126, #17336 ) ; +#55020 = EDGE_CURVE ( 'NONE', #61838, #47424, #5361, .T. ) ; +#55021 = VERTEX_POINT ( 'NONE', #27915 ) ; +#55022 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.000000000000000000 ) ) ; +#55023 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55024 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#55025 = SURFACE_STYLE_FILL_AREA ( #5964 ) ; +#55026 = EDGE_CURVE ( 'NONE', #16321, #28255, #44192, .T. ) ; +#55027 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55028 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#55029 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#55030 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55031 = CYLINDRICAL_SURFACE ( 'NONE', #32685, 0.04999999999999991257 ) ; +#55032 = VECTOR ( 'NONE', #61174, 1000.000000000000000 ) ; +#55033 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#55034 = FACE_OUTER_BOUND ( 'NONE', #79694, .T. ) ; +#55035 = EDGE_CURVE ( 'NONE', #25439, #43289, #90153, .T. ) ; +#55036 = FACE_OUTER_BOUND ( 'NONE', #91468, .T. ) ; +#55037 = SURFACE_STYLE_FILL_AREA ( #15677 ) ; +#55038 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#55039 = FILL_AREA_STYLE ('',( #93767 ) ) ; +#55040 = STYLED_ITEM ( 'NONE', ( #59835 ), #83991 ) ; +#55041 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3438 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8440, #25402, #70822 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55042 = LINE ( 'NONE', #78005, #63259 ) ; +#55043 = SURFACE_STYLE_FILL_AREA ( #40220 ) ; +#55044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55045 = VERTEX_POINT ( 'NONE', #20212 ) ; +#55046 = FACE_OUTER_BOUND ( 'NONE', #52545, .T. ) ; +#55048 = STYLED_ITEM ( 'NONE', ( #13364 ), #55248 ) ; +#55047 = SURFACE_STYLE_USAGE ( .BOTH. , #8978 ) ; +#55049 = CARTESIAN_POINT ( 'NONE', ( 1.566431021886530051, -1.318798174699070014, 0.8299999999999977396 ) ) ; +#55050 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55053 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#55052 = CARTESIAN_POINT ( 'NONE', ( 0.01546163603480650052, -1.327673353236110021, 0.8300000000000002931 ) ) ; +#55051 = AXIS2_PLACEMENT_3D ( 'NONE', #50127, #96016, #74079 ) ; +#55054 = CARTESIAN_POINT ( 'NONE', ( 1.119510237106087436, -0.9639334565574937397, 0.8100000000000122657 ) ) ; +#55055 = EDGE_CURVE ( 'NONE', #93078, #86631, #59070, .T. ) ; +#55056 = EDGE_CURVE ( 'NONE', #91599, #47892, #99248, .T. ) ; +#55057 = PRESENTATION_STYLE_ASSIGNMENT (( #94812 ) ) ; +#55058 = SURFACE_STYLE_USAGE ( .BOTH. , #92781 ) ; +#55060 = EDGE_LOOP ( 'NONE', ( #62748, #49064, #56184, #22911, #85718, #11487 ) ) ; +#55059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #479 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27279, #74233, #17561 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55061 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6020 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20457, #67423, #39816 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55062 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#55063 = SURFACE_SIDE_STYLE ('',( #56066 ) ) ; +#55064 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55065 = STYLED_ITEM ( 'NONE', ( #29278 ), #41414 ) ; +#55066 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55067 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#55068 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55069 = STYLED_ITEM ( 'NONE', ( #10104 ), #23222 ) ; +#55070 = CLOSED_SHELL ( 'NONE', ( #80857, #68746, #57708, #33154, #33594, #56490 ) ) ; +#55071 = MANIFOLD_SOLID_BREP ( 'ÊäÈë93', #38644 ) ; +#55072 = ADVANCED_FACE ( 'NONE', ( #82527 ), #83021, .T. ) ; +#55073 = VECTOR ( 'NONE', #29622, 1000.000000000000000 ) ; +#55074 = ORIENTED_EDGE ( 'NONE', *, *, #21603, .T. ) ; +#55075 = ORIENTED_EDGE ( 'NONE', *, *, #20089, .F. ) ; +#55076 = EDGE_CURVE ( 'NONE', #48469, #99643, #100509, .T. ) ; +#55077 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72992 ) ) ; +#55078 = LINE ( 'NONE', #1437, #1462 ) ; +#55079 = ORIENTED_EDGE ( 'NONE', *, *, #42731, .T. ) ; +#55080 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55081 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55082 = PLANE ( 'NONE', #64657 ) ; +#55083 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55084 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55085 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, -3.500000000000000444, 0.000000000000000000 ) ) ; +#55086 = SHAPE_DEFINITION_REPRESENTATION ( #74288, #57968 ) ; +#55087 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#55088 = LINE ( 'NONE', #86189, #8124 ) ; +#55089 = CIRCLE ( 'NONE', #32259, 0.04341445994558928989 ) ; +#55091 = EDGE_LOOP ( 'NONE', ( #38984, #82089, #50996, #95170 ) ) ; +#55090 = EDGE_LOOP ( 'NONE', ( #81829, #97576, #18387, #24857 ) ) ; +#55092 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95773 ), #68083 ) ; +#55093 = VERTEX_POINT ( 'NONE', #69676 ) ; +#55094 = FILL_AREA_STYLE_COLOUR ( '', #34455 ) ; +#55095 = ADVANCED_FACE ( 'NONE', ( #70697 ), #77342, .T. ) ; +#55096 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62582, 'distance_accuracy_value', 'NONE'); +#55098 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55097 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55099 = ORIENTED_EDGE ( 'NONE', *, *, #35035, .T. ) ; +#55100 = FILL_AREA_STYLE ('',( #69333 ) ) ; +#55101 = ADVANCED_FACE ( 'NONE', ( #47221 ), #54913, .T. ) ; +#55102 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55104 = PRESENTATION_STYLE_ASSIGNMENT (( #31082 ) ) ; +#55103 = FILL_AREA_STYLE ('',( #86720 ) ) ; +#55106 = VERTEX_POINT ( 'NONE', #53880 ) ; +#55105 = VECTOR ( 'NONE', #68490, 1000.000000000000000 ) ; +#55108 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55107 = LINE ( 'NONE', #954, #24273 ) ; +#55109 = ORIENTED_EDGE ( 'NONE', *, *, #99041, .F. ) ; +#55110 = EDGE_LOOP ( 'NONE', ( #66537, #100248, #91336, #36749 ) ) ; +#55111 = SURFACE_STYLE_FILL_AREA ( #62256 ) ; +#55112 = EDGE_CURVE ( 'NONE', #86302, #80244, #41098, .T. ) ; +#55113 = STYLED_ITEM ( 'NONE', ( #63567 ), #31131 ) ; +#55114 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000019873, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#55115 = EDGE_CURVE ( 'NONE', #2486, #43767, #42092, .T. ) ; +#55116 = SURFACE_STYLE_USAGE ( .BOTH. , #23973 ) ; +#55118 = EDGE_LOOP ( 'NONE', ( #15610, #51080, #5494, #86127 ) ) ; +#55117 = SURFACE_STYLE_USAGE ( .BOTH. , #25984 ) ; +#55119 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#55120 = AXIS2_PLACEMENT_3D ( 'NONE', #81052, #88197, #10988 ) ; +#55121 = STYLED_ITEM ( 'NONE', ( #16543 ), #91222 ) ; +#55122 = FACE_OUTER_BOUND ( 'NONE', #77029, .T. ) ; +#55123 = ORIENTED_EDGE ( 'NONE', *, *, #4371, .T. ) ; +#55124 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.816666666666666652, 0.000000000000000000 ) ) ; +#55125 = EDGE_LOOP ( 'NONE', ( #84351, #44089, #31060, #22192 ) ) ; +#55126 = ORIENTED_EDGE ( 'NONE', *, *, #38394, .T. ) ; +#55127 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#55128 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55129 = CARTESIAN_POINT ( 'NONE', ( -0.5075789211564899484, -1.256245978568790056, 0.8299999999999999600 ) ) ; +#55130 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55131 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, -3.500000000000000444, 0.000000000000000000 ) ) ; +#55132 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55134 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55133 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38664, 'distance_accuracy_value', 'NONE'); +#55135 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55136 = ORIENTED_EDGE ( 'NONE', *, *, #80631, .T. ) ; +#55137 = CARTESIAN_POINT ( 'NONE', ( 0.4653200840722879761, -1.100151516462789969, 0.8100000000000000533 ) ) ; +#55138 = EDGE_CURVE ( 'NONE', #69464, #8279, #9845, .T. ) ; +#55139 = VECTOR ( 'NONE', #85388, 1000.000000000000000 ) ; +#55140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31576 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21349, #13617, #5970 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55141 = CARTESIAN_POINT ( 'NONE', ( 0.07873568626789680114, -1.258231835375339891, 0.8299999999999999600 ) ) ; +#55142 = ORIENTED_EDGE ( 'NONE', *, *, #100516, .F. ) ; +#55143 = SURFACE_STYLE_USAGE ( .BOTH. , #22448 ) ; +#55144 = FILL_AREA_STYLE_COLOUR ( '', #54617 ) ; +#55145 = STYLED_ITEM ( 'NONE', ( #12664 ), #16588 ) ; +#55146 = SURFACE_SIDE_STYLE ('',( #94396 ) ) ; +#55147 = SURFACE_SIDE_STYLE ('',( #79630 ) ) ; +#55148 = VECTOR ( 'NONE', #30396, 1000.000000000000000 ) ; +#55150 = SURFACE_STYLE_FILL_AREA ( #14240 ) ; +#55149 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#55151 = CARTESIAN_POINT ( 'NONE', ( 1.783305012356700026, -1.001398657004090254, 0.8299999999999999600 ) ) ; +#55152 = FILL_AREA_STYLE_COLOUR ( '', #30479 ) ; +#55153 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55155 = EDGE_CURVE ( 'NONE', #95850, #77743, #87041, .T. ) ; +#55154 = SURFACE_STYLE_USAGE ( .BOTH. , #24006 ) ; +#55156 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.251909075926969983, 0.8299999999999999600 ) ) ; +#55157 = EDGE_CURVE ( 'NONE', #81292, #61010, #48759, .T. ) ; +#55158 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55159 = CIRCLE ( 'NONE', #66347, 0.009999999999999998473 ) ; +#55160 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6471 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1557, #16820, #26058 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55161 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, 0.000000000000000000 ) ) ; +#55162 = LINE ( 'NONE', #31633, #79831 ) ; +#55163 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55164 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#55165 = ADVANCED_FACE ( 'NONE', ( #26282 ), #64069, .T. ) ; +#55166 = VECTOR ( 'NONE', #43333, 1000.000000000000000 ) ; +#55167 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.699999999999999956, 0.8299999999999999600 ) ) ; +#55168 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, 0.1350000000000000089 ) ) ; +#55169 = ADVANCED_FACE ( 'NONE', ( #2293 ), #25291, .F. ) ; +#55170 = SURFACE_STYLE_USAGE ( .BOTH. , #70432 ) ; +#55171 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99058 ), #7734 ) ; +#55172 = ORIENTED_EDGE ( 'NONE', *, *, #30362, .F. ) ; +#55173 = FILL_AREA_STYLE_COLOUR ( '', #34615 ) ; +#55174 = FILL_AREA_STYLE_COLOUR ( '', #33973 ) ; +#55175 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55176 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38433, 'distance_accuracy_value', 'NONE'); +#55177 = VERTEX_POINT ( 'NONE', #11355 ) ; +#55178 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66199, 'distance_accuracy_value', 'NONE'); +#55179 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#55180 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55181 = LINE ( 'NONE', #22482, #45136 ) ; +#55182 = LINE ( 'NONE', #1539, #99166 ) ; +#55183 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55184 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2973 ), #99071 ) ; +#55185 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55186 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55187 = EDGE_CURVE ( 'NONE', #23378, #99535, #73730, .T. ) ; +#55188 = ORIENTED_EDGE ( 'NONE', *, *, #16857, .T. ) ; +#55189 = SURFACE_SIDE_STYLE ('',( #24036 ) ) ; +#55190 = ORIENTED_EDGE ( 'NONE', *, *, #2205, .T. ) ; +#55191 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61482, 'distance_accuracy_value', 'NONE'); +#55192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67667, 'distance_accuracy_value', 'NONE'); +#55193 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55194 = FACE_OUTER_BOUND ( 'NONE', #17623, .T. ) ; +#55195 = PRESENTATION_STYLE_ASSIGNMENT (( #93908 ) ) ; +#55196 = STYLED_ITEM ( 'NONE', ( #56306 ), #91441 ) ; +#55197 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#55198 = LINE ( 'NONE', #30638, #63169 ) ; +#55199 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55200 = VERTEX_POINT ( 'NONE', #35460 ) ; +#55201 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55202 = ORIENTED_EDGE ( 'NONE', *, *, #9476, .T. ) ; +#55203 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#55204 = EDGE_CURVE ( 'NONE', #68717, #51624, #51767, .T. ) ; +#55205 = ORIENTED_EDGE ( 'NONE', *, *, #16516, .T. ) ; +#55206 = FILL_AREA_STYLE ('',( #24578 ) ) ; +#55207 = ADVANCED_FACE ( 'NONE', ( #45055 ), #75246, .T. ) ; +#55208 = CARTESIAN_POINT ( 'NONE', ( 1.036559900398249967, -1.306787212278190058, 0.8299999999999999600 ) ) ; +#55209 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43799 ), #6198 ) ; +#55210 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6166666666666666963, 0.000000000000000000 ) ) ; +#55211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55212 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22516 ) ) ; +#55214 = ORIENTED_EDGE ( 'NONE', *, *, #27751, .F. ) ; +#55213 = ORIENTED_EDGE ( 'NONE', *, *, #54712, .T. ) ; +#55215 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50346 ), #3004 ) ; +#55217 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61340 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56576, #80548, #25926 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55216 = FACE_OUTER_BOUND ( 'NONE', #36646, .T. ) ; +#55218 = ORIENTED_EDGE ( 'NONE', *, *, #98996, .F. ) ; +#55219 = STYLED_ITEM ( 'NONE', ( #17368 ), #23873 ) ; +#55221 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55220 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55222 = VECTOR ( 'NONE', #52717, 1000.000000000000000 ) ; +#55223 = ORIENTED_EDGE ( 'NONE', *, *, #89069, .F. ) ; +#55224 = VERTEX_POINT ( 'NONE', #36442 ) ; +#55225 = SURFACE_STYLE_FILL_AREA ( #84323 ) ; +#55226 = CARTESIAN_POINT ( 'NONE', ( -0.2157361669573319984, -1.030915998478540097, 0.8300000000000000711 ) ) ; +#55228 = FACE_OUTER_BOUND ( 'NONE', #15641, .T. ) ; +#55227 = SURFACE_STYLE_FILL_AREA ( #54716 ) ; +#55229 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#55231 = EDGE_LOOP ( 'NONE', ( #4918, #72786, #18767, #95222 ) ) ; +#55230 = VECTOR ( 'NONE', #100323, 1000.000000000000000 ) ; +#55232 = ORIENTED_EDGE ( 'NONE', *, *, #99861, .F. ) ; +#55233 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 7.261168999999999762, 0.8648700000000000276 ) ) ; +#55234 = VERTEX_POINT ( 'NONE', #12362 ) ; +#55235 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65045 ), #68299 ) ; +#55236 = LINE ( 'NONE', #86860, #28099 ) ; +#55237 = EDGE_CURVE ( 'NONE', #58620, #79954, #68550, .T. ) ; +#55240 = ORIENTED_EDGE ( 'NONE', *, *, #46281, .F. ) ; +#55239 = AXIS2_PLACEMENT_3D ( 'NONE', #42967, #56822, #34339 ) ; +#55238 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#55241 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#55242 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55243 = EDGE_LOOP ( 'NONE', ( #25358, #38156, #86590, #36126 ) ) ; +#55244 = EDGE_CURVE ( 'NONE', #61112, #62754, #59951, .T. ) ; +#55245 = LINE ( 'NONE', #7642, #45179 ) ; +#55246 = SURFACE_SIDE_STYLE ('',( #94497 ) ) ; +#55247 = ORIENTED_EDGE ( 'NONE', *, *, #91828, .F. ) ; +#55248 = MANIFOLD_SOLID_BREP ( 'ÊäÈë134', #14109 ) ; +#55249 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55250 = FILL_AREA_STYLE ('',( #64397 ) ) ; +#55251 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94332 ) ) ; +#55252 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#55253 = ORIENTED_EDGE ( 'NONE', *, *, #77036, .F. ) ; +#55254 = LINE ( 'NONE', #64898, #36227 ) ; +#55255 = CARTESIAN_POINT ( 'NONE', ( 1.549081571661369949, -1.457888621141530061, 0.8299999999999999600 ) ) ; +#55256 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42199 ), #37315 ) ; +#55257 = EDGE_CURVE ( 'NONE', #18897, #48043, #67060, .T. ) ; +#55258 = PLANE ( 'NONE', #69036 ) ; +#55259 = VERTEX_POINT ( 'NONE', #81909 ) ; +#55260 = FILL_AREA_STYLE_COLOUR ( '', #100580 ) ; +#55261 = SURFACE_STYLE_USAGE ( .BOTH. , #7663 ) ; +#55262 = CARTESIAN_POINT ( 'NONE', ( -0.3092775381631849840, -1.357596283920579960, 0.8100000000000000533 ) ) ; +#55263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69859 ) ) ; +#55264 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#55265 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55266 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.000000000000000000, 1.149999999999999911 ) ) ; +#55267 = AXIS2_PLACEMENT_3D ( 'NONE', #72239, #33459, #49273 ) ; +#55269 = EDGE_CURVE ( 'NONE', #83662, #5073, #96673, .T. ) ; +#55268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55270 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#55271 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78133 ) ) ; +#55272 = ORIENTED_EDGE ( 'NONE', *, *, #100465, .T. ) ; +#55273 = SURFACE_SIDE_STYLE ('',( #64423 ) ) ; +#55274 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55275 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97333 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83115, #82614, #35166 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55276 = VERTEX_POINT ( 'NONE', #6217 ) ; +#55277 = PRESENTATION_STYLE_ASSIGNMENT (( #93995 ) ) ; +#55278 = AXIS2_PLACEMENT_3D ( 'NONE', #34461, #91058, #51771 ) ; +#55280 = FILL_AREA_STYLE ('',( #17924 ) ) ; +#55279 = SURFACE_SIDE_STYLE ('',( #70558 ) ) ; +#55281 = EDGE_CURVE ( 'NONE', #90356, #69997, #29273, .T. ) ; +#55282 = FILL_AREA_STYLE_COLOUR ( '', #35403 ) ; +#55283 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55284 = FILL_AREA_STYLE_COLOUR ( '', #15113 ) ; +#55285 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55286 = EDGE_CURVE ( 'NONE', #31808, #40649, #8704, .T. ) ; +#55287 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #64663, #55523, #10424, #73345 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55288 = EDGE_LOOP ( 'NONE', ( #24594, #57900, #36160, #14073 ) ) ; +#55289 = SURFACE_STYLE_USAGE ( .BOTH. , #77216 ) ; +#55290 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92723, #33905, #22828, #10292 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55291 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55292 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55293 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55294 = FILL_AREA_STYLE_COLOUR ( '', #100639 ) ; +#55295 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#55296 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55297 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55298 = FACE_OUTER_BOUND ( 'NONE', #57198, .T. ) ; +#55299 = SURFACE_STYLE_USAGE ( .BOTH. , #39432 ) ; +#55300 = CARTESIAN_POINT ( 'NONE', ( -0.02383637504043630354, -0.9153515042605530061, 0.8299999999999999600 ) ) ; +#55301 = EDGE_CURVE ( 'NONE', #94347, #26946, #92037, .T. ) ; +#55302 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67459, 'distance_accuracy_value', 'NONE'); +#55304 = EDGE_CURVE ( 'NONE', #76431, #46528, #78739, .T. ) ; +#55303 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29184 ) ) ; +#55305 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000089, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#55306 = ORIENTED_EDGE ( 'NONE', *, *, #8540, .T. ) ; +#55307 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55308 = ORIENTED_EDGE ( 'NONE', *, *, #92507, .F. ) ; +#55309 = SURFACE_STYLE_USAGE ( .BOTH. , #48644 ) ; +#55310 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88396, 'distance_accuracy_value', 'NONE'); +#55311 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #736, 'distance_accuracy_value', 'NONE'); +#55312 = ADVANCED_FACE ( 'NONE', ( #94014 ), #71093, .F. ) ; +#55313 = ADVANCED_FACE ( 'NONE', ( #93522 ), #92524, .T. ) ; +#55314 = PLANE ( 'NONE', #21156 ) ; +#55315 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 8.109697000000000600, 0.8991599999999999593 ) ) ; +#55316 = FILL_AREA_STYLE ('',( #64459 ) ) ; +#55317 = FACE_OUTER_BOUND ( 'NONE', #7570, .T. ) ; +#55318 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#55319 = CARTESIAN_POINT ( 'NONE', ( 0.003128152952664109854, -1.177156496261070107, 0.8299999999999999600 ) ) ; +#55320 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000009215, 0.2500000000000000000, 0.6999285677838846809 ) ) ; +#55321 = ORIENTED_EDGE ( 'NONE', *, *, #77065, .F. ) ; +#55322 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55323 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#55324 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63021, 'distance_accuracy_value', 'NONE'); +#55325 = ORIENTED_EDGE ( 'NONE', *, *, #85222, .T. ) ; +#55326 = CARTESIAN_POINT ( 'NONE', ( 1.324985677079354440, -1.264235153807147682, 0.8099999999998236389 ) ) ; +#55327 = EDGE_CURVE ( 'NONE', #100318, #67111, #14903, .T. ) ; +#55328 = CARTESIAN_POINT ( 'NONE', ( 0.9238200612200860862, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#55329 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53687 ) ) ; +#55330 = ORIENTED_EDGE ( 'NONE', *, *, #23021, .T. ) ; +#55331 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55332 = SURFACE_STYLE_FILL_AREA ( #95072 ) ; +#55333 = ADVANCED_FACE ( 'NONE', ( #77224 ), #7201, .F. ) ; +#55334 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.000000000000000000, -13.54999999999999893 ) ) ; +#55335 = PLANE ( 'NONE', #97098 ) ; +#55336 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55337 = ORIENTED_EDGE ( 'NONE', *, *, #97765, .F. ) ; +#55338 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#55339 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55340 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55341 = PLANE ( 'NONE', #18209 ) ; +#55342 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55567 ), #24365 ) ; +#55343 = SURFACE_STYLE_FILL_AREA ( #32335 ) ; +#55344 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55345 = ORIENTED_EDGE ( 'NONE', *, *, #14598, .F. ) ; +#55346 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#55347 = SURFACE_SIDE_STYLE ('',( #64987 ) ) ; +#55348 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.449999999999999956, -0.2000000000000000111 ) ) ; +#55349 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52133 ), #84673 ) ; +#55350 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#55351 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999996625, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#55352 = ORIENTED_EDGE ( 'NONE', *, *, #8599, .F. ) ; +#55353 = VERTEX_POINT ( 'NONE', #95929 ) ; +#55354 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55355 = EDGE_LOOP ( 'NONE', ( #98698, #64639, #48448, #75171 ) ) ; +#55356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55357 = STYLED_ITEM ( 'NONE', ( #18720 ), #63854 ) ; +#55358 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55359 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#55360 = EDGE_CURVE ( 'NONE', #74032, #46588, #88308, .T. ) ; +#55361 = ORIENTED_EDGE ( 'NONE', *, *, #92143, .F. ) ; +#55363 = VERTEX_POINT ( 'NONE', #49511 ) ; +#55362 = LINE ( 'NONE', #47152, #81921 ) ; +#55364 = VECTOR ( 'NONE', #1386, 1000.000000000000000 ) ; +#55365 = LINE ( 'NONE', #76786, #62187 ) ; +#55366 = FILL_AREA_STYLE_COLOUR ( '', #50954 ) ; +#55367 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55368 = AXIS2_PLACEMENT_3D ( 'NONE', #39786, #64278, #25001 ) ; +#55369 = EDGE_LOOP ( 'NONE', ( #49982, #73758, #77563, #98309, #19529, #73804, #35176, #62467, #41786, #29296 ) ) ; +#55371 = ADVANCED_FACE ( 'NONE', ( #18839 ), #2537, .T. ) ; +#55370 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55372 = CARTESIAN_POINT ( 'NONE', ( 1.743271607193970008, -1.437850337629750008, 0.8099999999999997202 ) ) ; +#55373 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55374 = ORIENTED_EDGE ( 'NONE', *, *, #1496, .T. ) ; +#55375 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55376 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55377 = ORIENTED_EDGE ( 'NONE', *, *, #83697, .T. ) ; +#55379 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, -3.149999999999979927, 0.000000000000000000 ) ) ; +#55378 = CARTESIAN_POINT ( 'NONE', ( -1.150000000000000133, 0.6892893218813450629, 1.100000000000000089 ) ) ; +#55380 = ORIENTED_EDGE ( 'NONE', *, *, #23555, .T. ) ; +#55381 = LINE ( 'NONE', #95627, #88177 ) ; +#55382 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55383 = AXIS2_PLACEMENT_3D ( 'NONE', #13015, #27943, #60106 ) ; +#55384 = LINE ( 'NONE', #61019, #41767 ) ; +#55385 = ORIENTED_EDGE ( 'NONE', *, *, #33304, .T. ) ; +#55386 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55388 = SURFACE_STYLE_FILL_AREA ( #55877 ) ; +#55387 = PRESENTATION_STYLE_ASSIGNMENT (( #48216 ) ) ; +#55389 = SURFACE_SIDE_STYLE ('',( #47692 ) ) ; +#55390 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8991599999999999593 ) ) ; +#55391 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43861, 'distance_accuracy_value', 'NONE'); +#55392 = VECTOR ( 'NONE', #98640, 1000.000000000000000 ) ; +#55393 = CARTESIAN_POINT ( 'NONE', ( -0.9449124846862100302, -1.010972591757870021, 0.8100000000000000533 ) ) ; +#55394 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, 1.050000000000000044 ) ) ; +#55395 = SURFACE_STYLE_USAGE ( .BOTH. , #22708 ) ; +#55396 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#55397 = LINE ( 'NONE', #47190, #52602 ) ; +#55398 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55399 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#55400 = STYLED_ITEM ( 'NONE', ( #78608 ), #32062 ) ; +#55401 = ORIENTED_EDGE ( 'NONE', *, *, #14428, .T. ) ; +#55402 = CARTESIAN_POINT ( 'NONE', ( -1.293371091536239970, -1.061634207873779934, 0.8300000000000002931 ) ) ; +#55404 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#55403 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8648700000000000276 ) ) ; +#55405 = CARTESIAN_POINT ( 'NONE', ( 1.027124486614658050, 0.8310340759269665423, 0.8100000000000000533 ) ) ; +#55406 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55407 = CIRCLE ( 'NONE', #43927, 0.1200000000000000927 ) ; +#55408 = FILL_AREA_STYLE_COLOUR ( '', #41953 ) ; +#55409 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#55410 = DIRECTION ( 'NONE', ( -0.7071075504167435577, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#55411 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55412 = EDGE_LOOP ( 'NONE', ( #39164, #81085, #81576, #99874 ) ) ; +#55414 = MANIFOLD_SOLID_BREP ( 'ÊäÈë4', #6070 ) ; +#55413 = FILL_AREA_STYLE_COLOUR ( '', #91251 ) ; +#55415 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55416 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#55417 = SURFACE_SIDE_STYLE ('',( #39062 ) ) ; +#55418 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.449999999999999956, -11.36999999999999922 ) ) ; +#55419 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999994, 0.8648700000000000276 ) ) ; +#55420 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55421 = FACE_OUTER_BOUND ( 'NONE', #74554, .T. ) ; +#55422 = PRESENTATION_STYLE_ASSIGNMENT (( #38062 ) ) ; +#55423 = FACE_OUTER_BOUND ( 'NONE', #26364, .T. ) ; +#55424 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#55425 = LINE ( 'NONE', #69680, #14900 ) ; +#55426 = PLANE ( 'NONE', #81679 ) ; +#55427 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#55428 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55429 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#55430 = VECTOR ( 'NONE', #47693, 1000.000000000000000 ) ; +#55431 = CARTESIAN_POINT ( 'NONE', ( 0.1073457792207792721, 0.6899999999999999467, 0.1493506493506491228 ) ) ; +#55432 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#55433 = ORIENTED_EDGE ( 'NONE', *, *, #15815, .T. ) ; +#55434 = FILL_AREA_STYLE_COLOUR ( '', #7140 ) ; +#55435 = ORIENTED_EDGE ( 'NONE', *, *, #33690, .T. ) ; +#55436 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66731, 'distance_accuracy_value', 'NONE'); +#55437 = ADVANCED_FACE ( 'NONE', ( #98386 ), #34712, .F. ) ; +#55438 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#55439 = CARTESIAN_POINT ( 'NONE', ( 0.1500588324485339908, -1.474796765042009961, 0.8100000000000000533 ) ) ; +#55440 = SURFACE_SIDE_STYLE ('',( #64580 ) ) ; +#55441 = SURFACE_STYLE_USAGE ( .BOTH. , #7842 ) ; +#55442 = CARTESIAN_POINT ( 'NONE', ( -1.166406359071090026, -1.149778012002649952, 0.8299999999999999600 ) ) ; +#55443 = ORIENTED_EDGE ( 'NONE', *, *, #79463, .F. ) ; +#55444 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72939, 'distance_accuracy_value', 'NONE'); +#55445 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55446 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55447 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17917 ), #75035 ) ; +#55448 = ORIENTED_EDGE ( 'NONE', *, *, #44656, .F. ) ; +#55449 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8648700000000000276 ) ) ; +#55450 = AXIS2_PLACEMENT_3D ( 'NONE', #38685, #29152, #28637 ) ; +#55451 = ADVANCED_FACE ( 'NONE', ( #67316 ), #38200, .T. ) ; +#55452 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55453 = SURFACE_STYLE_FILL_AREA ( #94189 ) ; +#55454 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#55455 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55456 = ORIENTED_EDGE ( 'NONE', *, *, #54001, .F. ) ; +#55457 = SURFACE_STYLE_FILL_AREA ( #39099 ) ; +#55458 = STYLED_ITEM ( 'NONE', ( #51798 ), #44760 ) ; +#55459 = LINE ( 'NONE', #43604, #34273 ) ; +#55460 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39244, 'distance_accuracy_value', 'NONE'); +#55461 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65194 ), #8019 ) ; +#55462 = SURFACE_SIDE_STYLE ('',( #46211 ) ) ; +#55463 = ORIENTED_EDGE ( 'NONE', *, *, #8582, .T. ) ; +#55464 = SURFACE_STYLE_USAGE ( .BOTH. , #69314 ) ; +#55465 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55466 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81570 ), #74976 ) ; +#55467 = ORIENTED_EDGE ( 'NONE', *, *, #99198, .T. ) ; +#55468 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55469 = LINE ( 'NONE', #16595, #71579 ) ; +#55470 = PRESENTATION_STYLE_ASSIGNMENT (( #2341 ) ) ; +#55471 = SURFACE_STYLE_USAGE ( .BOTH. , #17617 ) ; +#55472 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55473 = AXIS2_PLACEMENT_3D ( 'NONE', #90748, #82107, #52458 ) ; +#55474 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3257 ) ) ; +#55476 = EDGE_CURVE ( 'NONE', #95, #96771, #5496, .T. ) ; +#55475 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99363 ) ) ; +#55477 = CARTESIAN_POINT ( 'NONE', ( 0.3142305969234919782, -0.9692640729113169984, 0.8100000000000000533 ) ) ; +#55478 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55479 = EDGE_LOOP ( 'NONE', ( #74719, #29493, #68105, #14554 ) ) ; +#55481 = CARTESIAN_POINT ( 'NONE', ( -0.7892813355960819344, 1.536318883024137882, 0.8100000000000000533 ) ) ; +#55480 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55483 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55482 = PLANE ( 'NONE', #65572 ) ; +#55484 = SURFACE_STYLE_USAGE ( .BOTH. , #40647 ) ; +#55485 = STYLED_ITEM ( 'NONE', ( #39338 ), #81714 ) ; +#55486 = ADVANCED_FACE ( 'NONE', ( #83667 ), #13627, .T. ) ; +#55487 = ORIENTED_EDGE ( 'NONE', *, *, #60317, .F. ) ; +#55488 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44072 ) ) ; +#55489 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#55490 = EDGE_LOOP ( 'NONE', ( #61098, #27967, #50277, #789 ) ) ; +#55491 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47284 ) ) ; +#55492 = LINE ( 'NONE', #94232, #50451 ) ; +#55493 = ORIENTED_EDGE ( 'NONE', *, *, #97993, .T. ) ; +#55494 = VERTEX_POINT ( 'NONE', #77485 ) ; +#55495 = FILL_AREA_STYLE ('',( #46765 ) ) ; +#55496 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#55497 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51267 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73348, #25384, #26382 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55498 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55499 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76666 ), #47293 ) ; +#55500 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #57968 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #85566 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#55501 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#55502 = ORIENTED_EDGE ( 'NONE', *, *, #42635, .T. ) ; +#55503 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55505 = STYLED_ITEM ( 'NONE', ( #98125 ), #42855 ) ; +#55504 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.4999999999999994449, 0.1829999999999789573 ) ) ; +#55506 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55507 = ORIENTED_EDGE ( 'NONE', *, *, #23680, .T. ) ; +#55508 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55509 = EDGE_LOOP ( 'NONE', ( #58957, #98791, #17318, #96901, #72369, #41627, #70736, #12794 ) ) ; +#55510 = VERTEX_POINT ( 'NONE', #55563 ) ; +#55511 = FILL_AREA_STYLE ('',( #63668 ) ) ; +#55512 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#55513 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#55514 = ADVANCED_FACE ( 'NONE', ( #25420 ), #93773, .T. ) ; +#55515 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#55516 = VECTOR ( 'NONE', #4080, 1000.000000000000000 ) ; +#55517 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55519 = EDGE_CURVE ( 'NONE', #80630, #11036, #40224, .T. ) ; +#55518 = CARTESIAN_POINT ( 'NONE', ( -0.06821911881269179800, -1.154690592117219916, 0.8299999999999999600 ) ) ; +#55520 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47390 ), #71824 ) ; +#55521 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55522 = ORIENTED_EDGE ( 'NONE', *, *, #68138, .T. ) ; +#55523 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 1.300000000000000266, 3.495651678170121160E-76 ) ) ; +#55524 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1240, #24770, #32401, #94133 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55526 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55525 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55527 = CARTESIAN_POINT ( 'NONE', ( -0.9450130786088907220, -1.439563048828382819, 0.8099999999996645439 ) ) ; +#55528 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#55529 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#55530 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#55531 = CARTESIAN_POINT ( 'NONE', ( 9.568126999999998716, 10.98066299999999984, 0.8648700000000000276 ) ) ; +#55532 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.1499999999999999667, -0.02000000000000000042 ) ) ; +#55533 = PLANE ( 'NONE', #45092 ) ; +#55534 = EDGE_CURVE ( 'NONE', #38594, #85184, #79527, .T. ) ; +#55535 = ORIENTED_EDGE ( 'NONE', *, *, #90955, .T. ) ; +#55536 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.02000000000000000042, 0.000000000000000000 ) ) ; +#55537 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#55538 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55539 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, 0.2500000000000000000, -0.8499999999999997558 ) ) ; +#55540 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81629 ) ) ; +#55541 = DIRECTION ( 'NONE', ( -6.776263578034399754E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55542 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80083, 'distance_accuracy_value', 'NONE'); +#55543 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999966582, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#55544 = SURFACE_STYLE_FILL_AREA ( #46821 ) ; +#55545 = STYLED_ITEM ( 'NONE', ( #64637 ), #86168 ) ; +#55547 = FILL_AREA_STYLE_COLOUR ( '', #91483 ) ; +#55546 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13010 ) ) ; +#55548 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29871 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72443, #32665, #17309 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55549 = FACE_OUTER_BOUND ( 'NONE', #21396, .T. ) ; +#55550 = FILL_AREA_STYLE ('',( #88670 ) ) ; +#55551 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.005000000000000011380, -0.2500000000000000000 ) ) ; +#55552 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#55553 = PRESENTATION_STYLE_ASSIGNMENT (( #77997 ) ) ; +#55554 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9807 ), #65281 ) ; +#55555 = EDGE_CURVE ( 'NONE', #79941, #93940, #86673, .T. ) ; +#55556 = AXIS2_PLACEMENT_3D ( 'NONE', #42924, #35307, #58787 ) ; +#55557 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #47562, 'design' ) ; +#55558 = PRESENTATION_STYLE_ASSIGNMENT (( #62699 ) ) ; +#55559 = SURFACE_SIDE_STYLE ('',( #6952 ) ) ; +#55560 = FACE_OUTER_BOUND ( 'NONE', #98534, .T. ) ; +#55561 = ORIENTED_EDGE ( 'NONE', *, *, #79994, .T. ) ; +#55562 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8100000000000068257 ) ) ; +#55563 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999512, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#55564 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55565 = SURFACE_SIDE_STYLE ('',( #63219 ) ) ; +#55566 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12183, 'distance_accuracy_value', 'NONE'); +#55567 = STYLED_ITEM ( 'NONE', ( #6946 ), #80901 ) ; +#55569 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55568 = SURFACE_STYLE_USAGE ( .BOTH. , #24419 ) ; +#55570 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58778 ) ) ; +#55571 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55572 = CARTESIAN_POINT ( 'NONE', ( 1.394346260588942066, -1.224522408316681688, 0.8099999999998487299 ) ) ; +#55573 = ADVANCED_FACE ( 'NONE', ( #33053 ), #24415, .T. ) ; +#55574 = DIRECTION ( 'NONE', ( -0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#55575 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55576 = VERTEX_POINT ( 'NONE', #89691 ) ; +#55577 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42508 ) ) ; +#55578 = LINE ( 'NONE', #53535, #92768 ) ; +#55579 = AXIS2_PLACEMENT_3D ( 'NONE', #61, #55241, #100529 ) ; +#55580 = PLANE ( 'NONE', #62782 ) ; +#55581 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#55582 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.4999999999999991673, 0.8299999999999999600 ) ) ; +#55583 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55674, 'distance_accuracy_value', 'NONE'); +#55584 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70997, 'distance_accuracy_value', 'NONE'); +#55585 = CARTESIAN_POINT ( 'NONE', ( -3.235599999734661836E-06, -0.2350000046000000342, 0.2500000000000000000 ) ) ; +#55586 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#55587 = VERTEX_POINT ( 'NONE', #41234 ) ; +#55588 = ORIENTED_EDGE ( 'NONE', *, *, #38817, .T. ) ; +#55589 = VERTEX_POINT ( 'NONE', #96813 ) ; +#55590 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155856999999999690, 0.8991599999999999593 ) ) ; +#55591 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.383333333333333304, 0.000000000000000000 ) ) ; +#55592 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55593 = SHAPE_DEFINITION_REPRESENTATION ( #62167, #93053 ) ; +#55594 = SURFACE_SIDE_STYLE ('',( #78527 ) ) ; +#55595 = ADVANCED_FACE ( 'NONE', ( #81051 ), #50430, .F. ) ; +#55597 = EDGE_LOOP ( 'NONE', ( #74546, #65117, #69778, #82310 ) ) ; +#55596 = EDGE_LOOP ( 'NONE', ( #81374, #11405, #88444, #9014 ) ) ; +#55598 = ORIENTED_EDGE ( 'NONE', *, *, #8744, .F. ) ; +#55599 = ORIENTED_EDGE ( 'NONE', *, *, #26269, .T. ) ; +#55600 = PRESENTATION_STYLE_ASSIGNMENT (( #32090 ) ) ; +#55602 = PLANE ( 'NONE', #92077 ) ; +#55601 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 1.566666666666666652, 0.000000000000000000 ) ) ; +#55603 = ORIENTED_EDGE ( 'NONE', *, *, #75376, .F. ) ; +#55604 = EDGE_CURVE ( 'NONE', #85668, #27455, #49382, .T. ) ; +#55605 = FILL_AREA_STYLE ('',( #49955 ) ) ; +#55606 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.000000000000000000 ) ) ; +#55607 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999999237, 0.1458578643762690752 ) ) ; +#55608 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55609 = VERTEX_POINT ( 'NONE', #97315 ) ; +#55610 = FACE_BOUND ( 'NONE', #44851, .T. ) ; +#55611 = ORIENTED_EDGE ( 'NONE', *, *, #70489, .T. ) ; +#55612 = FILL_AREA_STYLE ('',( #95864 ) ) ; +#55613 = ORIENTED_EDGE ( 'NONE', *, *, #31359, .T. ) ; +#55614 = ORIENTED_EDGE ( 'NONE', *, *, #35127, .T. ) ; +#55615 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55616 = VECTOR ( 'NONE', #53505, 1000.000000000000000 ) ; +#55617 = VECTOR ( 'NONE', #25612, 1000.000000000000227 ) ; +#55619 = VERTEX_POINT ( 'NONE', #27413 ) ; +#55618 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#55620 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#55621 = SURFACE_STYLE_USAGE ( .BOTH. , #9042 ) ; +#55622 = AXIS2_PLACEMENT_3D ( 'NONE', #91627, #67152, #68641 ) ; +#55623 = FILL_AREA_STYLE ('',( #7022 ) ) ; +#55624 = ORIENTED_EDGE ( 'NONE', *, *, #75580, .F. ) ; +#55625 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55626 = ORIENTED_EDGE ( 'NONE', *, *, #76694, .F. ) ; +#55627 = ORIENTED_EDGE ( 'NONE', *, *, #20364, .F. ) ; +#55628 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1499999999999999667, -0.02000000000000000042 ) ) ; +#55629 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#55630 = SURFACE_STYLE_USAGE ( .BOTH. , #15236 ) ; +#55631 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55632 = VECTOR ( 'NONE', #55917, 1000.000000000000000 ) ; +#55634 = EDGE_CURVE ( 'NONE', #40957, #28607, #58499, .T. ) ; +#55633 = FILL_AREA_STYLE ('',( #24500 ) ) ; +#55635 = EDGE_CURVE ( 'NONE', #45151, #48855, #49909, .T. ) ; +#55636 = FILL_AREA_STYLE_COLOUR ( '', #34631 ) ; +#55637 = VECTOR ( 'NONE', #22594, 1000.000000000000000 ) ; +#55638 = EDGE_LOOP ( 'NONE', ( #35724, #84830, #6143, #80348 ) ) ; +#55639 = STYLED_ITEM ( 'NONE', ( #79086 ), #2246 ) ; +#55640 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#55641 = ORIENTED_EDGE ( 'NONE', *, *, #72299, .T. ) ; +#55642 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39342 ) ) ; +#55643 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55644 = CARTESIAN_POINT ( 'NONE', ( -0.4445834731179032495, -1.059528698560976867, 0.8300000000000001821 ) ) ; +#55645 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55646 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#55647 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55648 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 10.26637200000000050, 0.8648700000000000276 ) ) ; +#55649 = PLANE ( 'NONE', #1137 ) ; +#55650 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55651 = EDGE_CURVE ( 'NONE', #2960, #19442, #95808, .T. ) ; +#55652 = EDGE_CURVE ( 'NONE', #95182, #20227, #65709, .T. ) ; +#55653 = LINE ( 'NONE', #39279, #14999 ) ; +#55654 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 7.105604999999999727, 0.8648700000000000276 ) ) ; +#55655 = FILL_AREA_STYLE ('',( #2011 ) ) ; +#55656 = AXIS2_PLACEMENT_3D ( 'NONE', #56044, #62197, #55030 ) ; +#55657 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55658 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#55659 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8648700000000000276 ) ) ; +#55660 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69685 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3080, #96474, #10124 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55661 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.17581999999999987, 0.8648700000000000276 ) ) ; +#55662 = FILL_AREA_STYLE_COLOUR ( '', #96247 ) ; +#55663 = CARTESIAN_POINT ( 'NONE', ( 10.38419887512504403, 3.958979875125043346, 0.8648700000000000276 ) ) ; +#55665 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11530 ) ) ; +#55664 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#55666 = ADVANCED_FACE ( 'NONE', ( #34087 ), #65198, .F. ) ; +#55667 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72869, 'distance_accuracy_value', 'NONE'); +#55668 = ORIENTED_EDGE ( 'NONE', *, *, #61929, .F. ) ; +#55669 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#55670 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23393, #22904, #54559, #45148 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55671 = ORIENTED_EDGE ( 'NONE', *, *, #90764, .T. ) ; +#55672 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#55673 = EDGE_CURVE ( 'NONE', #76538, #94339, #61080, .T. ) ; +#55674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55675 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#55676 = STYLED_ITEM ( 'NONE', ( #94638 ), #18154 ) ; +#55677 = SURFACE_STYLE_FILL_AREA ( #45928 ) ; +#55678 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67085 ), #18147 ) ; +#55679 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2850000000000000311, -0.1458578643762690197 ) ) ; +#55680 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55681 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100943 ) ; +#55682 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55683 = ADVANCED_FACE ( 'NONE', ( #69167 ), #90694, .F. ) ; +#55684 = STYLED_ITEM ( 'NONE', ( #75721 ), #95605 ) ; +#55685 = VERTEX_POINT ( 'NONE', #29896 ) ; +#55686 = EDGE_CURVE ( 'NONE', #75115, #2124, #51907, .T. ) ; +#55687 = EDGE_LOOP ( 'NONE', ( #53306, #48513, #70269, #28937 ) ) ; +#55688 = AXIS2_PLACEMENT_3D ( 'NONE', #59799, #11682, #4604 ) ; +#55689 = PRESENTATION_STYLE_ASSIGNMENT (( #10098 ) ) ; +#55690 = SURFACE_STYLE_FILL_AREA ( #513 ) ; +#55691 = SURFACE_STYLE_FILL_AREA ( #9120 ) ; +#55692 = EDGE_CURVE ( 'NONE', #79728, #3602, #30376, .T. ) ; +#55693 = STYLED_ITEM ( 'NONE', ( #1640 ), #94920 ) ; +#55694 = LINE ( 'NONE', #56191, #91300 ) ; +#55695 = FILL_AREA_STYLE_COLOUR ( '', #7354 ) ; +#55696 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#55697 = LINE ( 'NONE', #57721, #72268 ) ; +#55698 = ORIENTED_EDGE ( 'NONE', *, *, #48711, .T. ) ; +#55699 = LINE ( 'NONE', #13, #40337 ) ; +#55700 = ORIENTED_EDGE ( 'NONE', *, *, #91318, .T. ) ; +#55701 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#55702 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55703 = CIRCLE ( 'NONE', #24744, 0.1000000000000000056 ) ; +#55704 = EDGE_LOOP ( 'NONE', ( #7511, #44255, #22686, #66580 ) ) ; +#55705 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#55706 = PRESENTATION_STYLE_ASSIGNMENT (( #77137 ) ) ; +#55707 = SURFACE_STYLE_FILL_AREA ( #57221 ) ; +#55708 = CARTESIAN_POINT ( 'NONE', ( -1.383450513385342084, 1.393384075926970000, 0.8100000000000001643 ) ) ; +#55709 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55710 = EDGE_CURVE ( 'NONE', #44212, #86804, #99271, .T. ) ; +#55711 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55713 = VERTEX_POINT ( 'NONE', #99733 ) ; +#55712 = ORIENTED_EDGE ( 'NONE', *, *, #91192, .T. ) ; +#55714 = FILL_AREA_STYLE_COLOUR ( '', #42160 ) ; +#55715 = ORIENTED_EDGE ( 'NONE', *, *, #91253, .F. ) ; +#55716 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55717 = ORIENTED_EDGE ( 'NONE', *, *, #58888, .T. ) ; +#55718 = ADVANCED_FACE ( 'NONE', ( #37091 ), #90176, .T. ) ; +#55719 = ORIENTED_EDGE ( 'NONE', *, *, #60439, .F. ) ; +#55720 = LINE ( 'NONE', #48044, #31857 ) ; +#55721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55722 = CARTESIAN_POINT ( 'NONE', ( -0.2243794914328909873, -1.066507643917919967, 0.8300000000000000711 ) ) ; +#55723 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55724 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#55725 = EDGE_LOOP ( 'NONE', ( #37626, #57439, #4104, #89589 ) ) ; +#55726 = EDGE_CURVE ( 'NONE', #28706, #19918, #30907, .T. ) ; +#55727 = ORIENTED_EDGE ( 'NONE', *, *, #72048, .F. ) ; +#55728 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18204 ) ) ; +#55729 = EDGE_LOOP ( 'NONE', ( #79310, #54043, #54056, #4960 ) ) ; +#55731 = ORIENTED_EDGE ( 'NONE', *, *, #11868, .T. ) ; +#55730 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55732 = SURFACE_STYLE_FILL_AREA ( #70004 ) ; +#55733 = LINE ( 'NONE', #71551, #7369 ) ; +#55734 = ORIENTED_EDGE ( 'NONE', *, *, #34104, .F. ) ; +#55735 = CARTESIAN_POINT ( 'NONE', ( -0.5614853896103889630, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#55736 = ORIENTED_EDGE ( 'NONE', *, *, #61929, .T. ) ; +#55737 = CARTESIAN_POINT ( 'NONE', ( -1.450000000000000178, 0.6599999999999998090, -0.9757359312880716784 ) ) ; +#55738 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#55739 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55740 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55741 = LINE ( 'NONE', #18919, #13365 ) ; +#55742 = AXIS2_PLACEMENT_3D ( 'NONE', #77439, #85610, #61157 ) ; +#55743 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#55744 = LINE ( 'NONE', #78694, #11150 ) ; +#55745 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #249 ), #23085 ) ; +#55746 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.000000000000000000, -13.54999999999999893 ) ) ; +#55747 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#55748 = SURFACE_STYLE_FILL_AREA ( #38407 ) ; +#55749 = EDGE_LOOP ( 'NONE', ( #37822, #80453, #9433, #7627 ) ) ; +#55750 = STYLED_ITEM ( 'NONE', ( #74291 ), #58928 ) ; +#55751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55752 = FILL_AREA_STYLE_COLOUR ( '', #65970 ) ; +#55753 = STYLED_ITEM ( 'NONE', ( #27652 ), #8501 ) ; +#55754 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55755 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8100000000000074918 ) ) ; +#55756 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4808578643762690952, 0.2434314575050761376 ) ) ; +#55758 = PRESENTATION_STYLE_ASSIGNMENT (( #23098 ) ) ; +#55757 = PLANE ( 'NONE', #28309 ) ; +#55759 = LINE ( 'NONE', #93492, #32372 ) ; +#55760 = VECTOR ( 'NONE', #83244, 1000.000000000000000 ) ; +#55761 = ADVANCED_FACE ( 'NONE', ( #772 ), #31931, .T. ) ; +#55762 = VECTOR ( 'NONE', #50039, 1000.000000000000000 ) ; +#55763 = ORIENTED_EDGE ( 'NONE', *, *, #81987, .T. ) ; +#55764 = EDGE_CURVE ( 'NONE', #29476, #84912, #78429, .T. ) ; +#55765 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55766 = ORIENTED_EDGE ( 'NONE', *, *, #14632, .T. ) ; +#55767 = AXIS2_PLACEMENT_3D ( 'NONE', #90059, #73748, #81931 ) ; +#55768 = FILL_AREA_STYLE_COLOUR ( '', #40715 ) ; +#55770 = CARTESIAN_POINT ( 'NONE', ( 0.7761769480519481457, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#55769 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.000000000000000000 ) ) ; +#55771 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55772 = FACE_OUTER_BOUND ( 'NONE', #16204, .T. ) ; +#55773 = AXIS2_PLACEMENT_3D ( 'NONE', #51290, #5764, #58974 ) ; +#55774 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5089, 'distance_accuracy_value', 'NONE'); +#55775 = EDGE_LOOP ( 'NONE', ( #33890, #61597, #52097, #89718 ) ) ; +#55776 = CARTESIAN_POINT ( 'NONE', ( 1.812952947087890232, -0.9302426320460149833, 0.8100000000000008304 ) ) ; +#55777 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#55778 = CARTESIAN_POINT ( 'NONE', ( -0.09936535710386810993, -1.163903542943879987, 0.8300000000000005151 ) ) ; +#55779 = SURFACE_SIDE_STYLE ('',( #31262 ) ) ; +#55780 = ADVANCED_FACE ( 'NONE', ( #70203 ), #63603, .F. ) ; +#55781 = SURFACE_STYLE_FILL_AREA ( #39425 ) ; +#55782 = SURFACE_SIDE_STYLE ('',( #70057 ) ) ; +#55783 = LINE ( 'NONE', #85389, #31870 ) ; +#55784 = AXIS2_PLACEMENT_3D ( 'NONE', #85898, #70577, #22615 ) ; +#55785 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, -3.123820061220065281, 0.000000000000000000 ) ) ; +#55786 = CARTESIAN_POINT ( 'NONE', ( 0.06710731395959769474, -1.024811280222130083, 0.8299999999999999600 ) ) ; +#55787 = CIRCLE ( 'NONE', #45954, 0.009999999999999998473 ) ; +#55788 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8648700000000000276 ) ) ; +#55789 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.300000000000000044, -0.02000000000000000042 ) ) ; +#55790 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#55791 = ORIENTED_EDGE ( 'NONE', *, *, #63168, .T. ) ; +#55792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55793 = EDGE_CURVE ( 'NONE', #37623, #20912, #38575, .T. ) ; +#55794 = VECTOR ( 'NONE', #7880, 1000.000000000000000 ) ; +#55795 = ORIENTED_EDGE ( 'NONE', *, *, #37480, .F. ) ; +#55796 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55797 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45831, 'distance_accuracy_value', 'NONE'); +#55798 = SURFACE_STYLE_FILL_AREA ( #24676 ) ; +#55799 = FILL_AREA_STYLE ('',( #79271 ) ) ; +#55800 = SURFACE_SIDE_STYLE ('',( #16433 ) ) ; +#55801 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109697000000000600, 0.8991599999999999593 ) ) ; +#55802 = FILL_AREA_STYLE ('',( #62463 ) ) ; +#55803 = CARTESIAN_POINT ( 'NONE', ( -0.05183531411288819918, -1.501723168847330259, 0.8300000000000004041 ) ) ; +#55804 = CARTESIAN_POINT ( 'NONE', ( 0.06449442099368349335, -1.103202958186300320, 0.8299999999999999600 ) ) ; +#55805 = SURFACE_SIDE_STYLE ('',( #62974 ) ) ; +#55806 = VERTEX_POINT ( 'NONE', #17088 ) ; +#55807 = CARTESIAN_POINT ( 'NONE', ( 1.900854206603999952, -1.350767436372750208, 0.8300000000000011813 ) ) ; +#55808 = PLANE ( 'NONE', #70464 ) ; +#55809 = VERTEX_POINT ( 'NONE', #54419 ) ; +#55810 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16611 ) ) ; +#55812 = AXIS2_PLACEMENT_3D ( 'NONE', #55833, #46095, #39482 ) ; +#55813 = FACE_OUTER_BOUND ( 'NONE', #6173, .T. ) ; +#55814 = VERTEX_POINT ( 'NONE', #79410 ) ; +#55815 = VECTOR ( 'NONE', #20549, 1000.000000000000000 ) ; +#55816 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49252 ) ) ; +#55817 = CIRCLE ( 'NONE', #83500, 1.968750814464449883 ) ; +#55818 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#55819 = ORIENTED_EDGE ( 'NONE', *, *, #78919, .T. ) ; +#55820 = VECTOR ( 'NONE', #1187, 1000.000000000000000 ) ; +#55821 = PRESENTATION_STYLE_ASSIGNMENT (( #32332 ) ) ; +#55822 = PRESENTATION_STYLE_ASSIGNMENT (( #7247 ) ) ; +#55823 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.2000000000000000111, -12.24500000000000099 ) ) ; +#55824 = CARTESIAN_POINT ( 'NONE', ( 0.4264791961179740243, -0.9850687526833949992, 0.8300000000000002931 ) ) ; +#55825 = EDGE_CURVE ( 'NONE', #73556, #1613, #53898, .T. ) ; +#55826 = STYLED_ITEM ( 'NONE', ( #53977 ), #8139 ) ; +#55827 = VERTEX_POINT ( 'NONE', #17585 ) ; +#55828 = PLANE ( 'NONE', #28512 ) ; +#55829 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55830 = FILL_AREA_STYLE_COLOUR ( '', #47917 ) ; +#55831 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55832 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59141 ), #338 ) ; +#55833 = CARTESIAN_POINT ( 'NONE', ( -0.7175359621965019530, 1.464383040805290026, 0.8299999999999999600 ) ) ; +#55834 = FILL_AREA_STYLE ('',( #23676 ) ) ; +#55835 = ORIENTED_EDGE ( 'NONE', *, *, #85614, .T. ) ; +#55836 = EDGE_CURVE ( 'NONE', #64584, #74888, #57453, .T. ) ; +#55838 = EDGE_LOOP ( 'NONE', ( #22550, #1153, #66845, #9011 ) ) ; +#55837 = ORIENTED_EDGE ( 'NONE', *, *, #97316, .T. ) ; +#55839 = FILL_AREA_STYLE_COLOUR ( '', #79228 ) ; +#55840 = ORIENTED_EDGE ( 'NONE', *, *, #82108, .T. ) ; +#55841 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.000000000000000000 ) ) ; +#55842 = ADVANCED_FACE ( 'NONE', ( #79925 ), #26806, .T. ) ; +#55843 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55844 = EDGE_LOOP ( 'NONE', ( #89364, #25092, #11422, #91764 ) ) ; +#55846 = VERTEX_POINT ( 'NONE', #56960 ) ; +#55845 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#55847 = SURFACE_STYLE_FILL_AREA ( #72658 ) ; +#55849 = PRESENTATION_STYLE_ASSIGNMENT (( #49714 ) ) ; +#55848 = CARTESIAN_POINT ( 'NONE', ( -0.7486876120449309502, 1.376287671486960074, 0.8100000000000000533 ) ) ; +#55850 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55851 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12772, #59363, #76132 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55852 = VERTEX_POINT ( 'NONE', #10356 ) ; +#55854 = ADVANCED_FACE ( 'NONE', ( #18076 ), #87561, .T. ) ; +#55853 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#55855 = ORIENTED_EDGE ( 'NONE', *, *, #76047, .T. ) ; +#55856 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999996669, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#55857 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.399999999999999911, -11.91999999999999993 ) ) ; +#55858 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#55859 = STYLED_ITEM ( 'NONE', ( #25923 ), #52325 ) ; +#55860 = ORIENTED_EDGE ( 'NONE', *, *, #32442, .T. ) ; +#55862 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#55861 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#55863 = VERTEX_POINT ( 'NONE', #21770 ) ; +#55865 = ADVANCED_FACE ( 'NONE', ( #14568 ), #11402, .F. ) ; +#55864 = FILL_AREA_STYLE_COLOUR ( '', #37873 ) ; +#55866 = EDGE_CURVE ( 'NONE', #62643, #1854, #30403, .T. ) ; +#55867 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55868 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55869 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55870 = AXIS2_PLACEMENT_3D ( 'NONE', #66640, #89644, #59553 ) ; +#55871 = EDGE_CURVE ( 'NONE', #28432, #56137, #1461, .T. ) ; +#55872 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, -2.000000000000000000, 0.000000000000000000 ) ) ; +#55873 = EDGE_CURVE ( 'NONE', #84465, #67087, #18626, .T. ) ; +#55874 = LINE ( 'NONE', #25737, #38544 ) ; +#55875 = ORIENTED_EDGE ( 'NONE', *, *, #67575, .T. ) ; +#55876 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.03333333333333168141, 0.000000000000000000 ) ) ; +#55877 = FILL_AREA_STYLE ('',( #39526 ) ) ; +#55878 = FILL_AREA_STYLE_COLOUR ( '', #51839 ) ; +#55879 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55880 = EDGE_CURVE ( 'NONE', #63839, #86226, #64608, .T. ) ; +#55881 = VECTOR ( 'NONE', #15591, 1000.000000000000114 ) ; +#55882 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70499 ) ) ; +#55883 = VECTOR ( 'NONE', #64043, 1000.000000000000000 ) ; +#55884 = CARTESIAN_POINT ( 'NONE', ( -1.069701591823909892, -0.8955552045491339541, 0.8299999999999999600 ) ) ; +#55885 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#55886 = FACE_BOUND ( 'NONE', #23230, .T. ) ; +#55887 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55888 = LINE ( 'NONE', #85485, #17763 ) ; +#55889 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34696 ), #65635 ) ; +#55890 = EDGE_CURVE ( 'NONE', #95326, #37922, #94711, .T. ) ; +#55892 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80308 ) ) ; +#55891 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#55893 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55894 = VECTOR ( 'NONE', #70596, 1000.000000000000000 ) ; +#55895 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#55896 = EDGE_LOOP ( 'NONE', ( #56655, #44720, #27220, #56521, #33365, #5222 ) ) ; +#55897 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55898 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261924000000000046, 0.8648700000000000276 ) ) ; +#55899 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.366666666666666696, 0.000000000000000000 ) ) ; +#55901 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51822 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83844, #82345, #98554 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#55900 = CYLINDRICAL_SURFACE ( 'NONE', #22736, 0.09999999999999939493 ) ; +#55902 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74577, 'distance_accuracy_value', 'NONE'); +#55903 = LINE ( 'NONE', #8818, #100559 ) ; +#55904 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000081, 0.8648700000000000276 ) ) ; +#55905 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83588 ) ) ; +#55906 = CARTESIAN_POINT ( 'NONE', ( -1.237444333805499896, -1.426518300252259897, 0.8299999999999998490 ) ) ; +#55907 = PLANE ( 'NONE', #42802 ) ; +#55908 = SURFACE_STYLE_FILL_AREA ( #8821 ) ; +#55909 = ORIENTED_EDGE ( 'NONE', *, *, #82762, .T. ) ; +#55910 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55911 = SURFACE_STYLE_FILL_AREA ( #63064 ) ; +#55912 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#55913 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55914 = SURFACE_STYLE_FILL_AREA ( #63578 ) ; +#55915 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#55916 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55917 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#55918 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#55919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55920 = SURFACE_STYLE_USAGE ( .BOTH. , #77346 ) ; +#55921 = FACE_OUTER_BOUND ( 'NONE', #25499, .T. ) ; +#55922 = CARTESIAN_POINT ( 'NONE', ( 1.078134533378849902, -1.401744930657430110, 0.8299999999999999600 ) ) ; +#55923 = SURFACE_SIDE_STYLE ('',( #88932 ) ) ; +#55924 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990585, 0.000000000000000000 ) ) ; +#55925 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#55926 = ORIENTED_EDGE ( 'NONE', *, *, #80417, .F. ) ; +#55927 = FILL_AREA_STYLE ('',( #2793 ) ) ; +#55929 = EDGE_CURVE ( 'NONE', #64241, #38123, #86577, .T. ) ; +#55928 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35897, #44025, #82842, #90492 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55930 = AXIS2_PLACEMENT_3D ( 'NONE', #90762, #20811, #3988 ) ; +#55931 = VERTEX_POINT ( 'NONE', #48314 ) ; +#55932 = LINE ( 'NONE', #33963, #95103 ) ; +#55933 = FILL_AREA_STYLE ('',( #24806 ) ) ; +#55935 = EDGE_CURVE ( 'NONE', #97150, #42881, #55469, .T. ) ; +#55934 = CARTESIAN_POINT ( 'NONE', ( 3.100999249749912146, 5.245913750250087659, 0.8991599999999999593 ) ) ; +#55936 = CARTESIAN_POINT ( 'NONE', ( -1.204575085674180146, -1.140452398731560013, 0.8299999999999999600 ) ) ; +#55937 = VERTEX_POINT ( 'NONE', #17119 ) ; +#55938 = FILL_AREA_STYLE_COLOUR ( '', #73192 ) ; +#55939 = STYLED_ITEM ( 'NONE', ( #84380 ), #87963 ) ; +#55940 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1911 ), #50909 ) ; +#55941 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55942 = ORIENTED_EDGE ( 'NONE', *, *, #54028, .F. ) ; +#55943 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#55944 = VECTOR ( 'NONE', #66267, 1000.000000000000000 ) ; +#55945 = AXIS2_PLACEMENT_3D ( 'NONE', #88322, #50057, #41868 ) ; +#55946 = SURFACE_STYLE_USAGE ( .BOTH. , #64593 ) ; +#55947 = PLANE ( 'NONE', #90208 ) ; +#55948 = SURFACE_STYLE_USAGE ( .BOTH. , #64096 ) ; +#55949 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#55950 = ADVANCED_FACE ( 'NONE', ( #32968 ), #87588, .T. ) ; +#55951 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#55952 = VERTEX_POINT ( 'NONE', #79438 ) ; +#55953 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#55954 = DIRECTION ( 'NONE', ( 0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#55955 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #156, 'distance_accuracy_value', 'NONE'); +#55956 = LINE ( 'NONE', #48303, #59230 ) ; +#55957 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105605000000000615, 0.8648700000000000276 ) ) ; +#55958 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42886 ), #81968 ) ; +#55959 = VECTOR ( 'NONE', #11222, 1000.000000000000114 ) ; +#55960 = LINE ( 'NONE', #49289, #4588 ) ; +#55961 = EDGE_CURVE ( 'NONE', #12696, #5920, #17615, .T. ) ; +#55962 = ORIENTED_EDGE ( 'NONE', *, *, #49486, .F. ) ; +#55963 = VECTOR ( 'NONE', #78916, 1000.000000000000000 ) ; +#55964 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#55965 = AXIS2_PLACEMENT_3D ( 'NONE', #72965, #79638, #9079 ) ; +#55966 = FILL_AREA_STYLE ('',( #24831 ) ) ; +#55967 = PRESENTATION_STYLE_ASSIGNMENT (( #88584 ) ) ; +#55968 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#55969 = ORIENTED_EDGE ( 'NONE', *, *, #1427, .F. ) ; +#55970 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#55971 = PLANE ( 'NONE', #66302 ) ; +#55972 = FILL_AREA_STYLE_COLOUR ( '', #30496 ) ; +#55973 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55974 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#55975 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82949, #73296, #66610, #49819 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#55976 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15071 ) ) ; +#55977 = ORIENTED_EDGE ( 'NONE', *, *, #2221, .T. ) ; +#55979 = VERTEX_POINT ( 'NONE', #9399 ) ; +#55978 = FILL_AREA_STYLE_COLOUR ( '', #80246 ) ; +#55980 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31446, 'distance_accuracy_value', 'NONE'); +#55981 = STYLED_ITEM ( 'NONE', ( #68856 ), #11308 ) ; +#55983 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#55982 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#55984 = PRESENTATION_STYLE_ASSIGNMENT (( #24846 ) ) ; +#55985 = SURFACE_STYLE_FILL_AREA ( #61752 ) ; +#55986 = ORIENTED_EDGE ( 'NONE', *, *, #43739, .T. ) ; +#55987 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55988 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -9.880000000000000782, 0.4000000000000000222 ) ) ; +#55989 = STYLED_ITEM ( 'NONE', ( #22766 ), #67121 ) ; +#55990 = EDGE_LOOP ( 'NONE', ( #36765, #9491, #9688, #49789 ) ) ; +#55991 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#55992 = EDGE_LOOP ( 'NONE', ( #96113, #53, #79891, #5921 ) ) ; +#55993 = ORIENTED_EDGE ( 'NONE', *, *, #82717, .T. ) ; +#55995 = FILL_AREA_STYLE_COLOUR ( '', #12415 ) ; +#55994 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#55996 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 1.149999999999999911, 0.000000000000000000 ) ) ; +#55997 = VECTOR ( 'NONE', #14608, 1000.000000000000000 ) ; +#55998 = VERTEX_POINT ( 'NONE', #49815 ) ; +#55999 = EDGE_CURVE ( 'NONE', #13508, #91364, #10379, .T. ) ; +#56000 = LINE ( 'NONE', #69759, #42485 ) ; +#56001 = ORIENTED_EDGE ( 'NONE', *, *, #19487, .F. ) ; +#56002 = CARTESIAN_POINT ( 'NONE', ( 1.325329304031209965, -1.416724300735810127, 0.8100000000000000533 ) ) ; +#56004 = ORIENTED_EDGE ( 'NONE', *, *, #43186, .F. ) ; +#56003 = AXIS2_PLACEMENT_3D ( 'NONE', #31308, #161, #61981 ) ; +#56005 = ORIENTED_EDGE ( 'NONE', *, *, #5130, .T. ) ; +#56007 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#56006 = FACE_OUTER_BOUND ( 'NONE', #42902, .T. ) ; +#56008 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8100000000000000533 ) ) ; +#56009 = LINE ( 'NONE', #17156, #31977 ) ; +#56010 = LINE ( 'NONE', #87135, #2516 ) ; +#56011 = EDGE_CURVE ( 'NONE', #66829, #79048, #3331, .T. ) ; +#56012 = STYLED_ITEM ( 'NONE', ( #22709 ), #88100 ) ; +#56013 = PRESENTATION_STYLE_ASSIGNMENT (( #74711 ) ) ; +#56014 = CARTESIAN_POINT ( 'NONE', ( 4.629999999999999893, 0.6999999999999999556, 0.000000000000000000 ) ) ; +#56015 = VECTOR ( 'NONE', #66331, 1000.000000000000000 ) ; +#56016 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44667 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9986, #8997, #40238 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56017 = FILL_AREA_STYLE ('',( #63174 ) ) ; +#56018 = EDGE_CURVE ( 'NONE', #2457, #28590, #88218, .T. ) ; +#56019 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.806970050855547879E-17, -0.8499999999999999778 ) ) ; +#56020 = ORIENTED_EDGE ( 'NONE', *, *, #59126, .F. ) ; +#56021 = VECTOR ( 'NONE', #6674, 1000.000000000000114 ) ; +#56022 = FILL_AREA_STYLE_COLOUR ( '', #97822 ) ; +#56023 = CARTESIAN_POINT ( 'NONE', ( 10.66704112487501099, 8.286473124875012530, 0.8648700000000000276 ) ) ; +#56024 = SURFACE_SIDE_STYLE ('',( #33544 ) ) ; +#56025 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56026 = LINE ( 'NONE', #47839, #19032 ) ; +#56027 = SURFACE_SIDE_STYLE ('',( #54516 ) ) ; +#56028 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11890 ), #20126 ) ; +#56029 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#56030 = ORIENTED_EDGE ( 'NONE', *, *, #37745, .F. ) ; +#56031 = SURFACE_STYLE_FILL_AREA ( #63193 ) ; +#56033 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13823, 'distance_accuracy_value', 'NONE'); +#56032 = SURFACE_STYLE_FILL_AREA ( #24392 ) ; +#56034 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56036 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88470, #27216, #57882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56035 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#56037 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56038 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57662 ), #54426 ) ; +#56039 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.164062568141495335, 0.8300000000000000711 ) ) ; +#56040 = FACE_OUTER_BOUND ( 'NONE', #40387, .T. ) ; +#56041 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 2.168404344971010347E-16 ) ) ; +#56042 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56043 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#56044 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.2300000000000000100, 0.6999999999999999556 ) ) ; +#56045 = SURFACE_STYLE_USAGE ( .BOTH. , #94790 ) ; +#56046 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56047 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#56048 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94901 ), #33220 ) ; +#56049 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56050 = SURFACE_STYLE_USAGE ( .BOTH. , #100832 ) ; +#56051 = CARTESIAN_POINT ( 'NONE', ( 1.874834857517529763, -1.237898259965849679, 0.8100000000000004974 ) ) ; +#56052 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78405 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24350, #78438, #30968 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56054 = EDGE_CURVE ( 'NONE', #82682, #46484, #60012, .T. ) ; +#56053 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56055 = ORIENTED_EDGE ( 'NONE', *, *, #9665, .T. ) ; +#56056 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853440755, 2.251909075926970427, 0.8100000000000000533 ) ) ; +#56057 = SURFACE_STYLE_USAGE ( .BOTH. , #7463 ) ; +#56058 = PRESENTATION_STYLE_ASSIGNMENT (( #63722 ) ) ; +#56059 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#56060 = LINE ( 'NONE', #94809, #33498 ) ; +#56061 = SURFACE_STYLE_FILL_AREA ( #87684 ) ; +#56062 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8648700000000000276 ) ) ; +#56063 = ORIENTED_EDGE ( 'NONE', *, *, #94530, .F. ) ; +#56064 = PRESENTATION_STYLE_ASSIGNMENT (( #57590 ) ) ; +#56065 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5484 ), #3923 ) ; +#56066 = SURFACE_STYLE_FILL_AREA ( #8993 ) ; +#56067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56068 = STYLED_ITEM ( 'NONE', ( #74153 ), #53316 ) ; +#56069 = PRESENTATION_STYLE_ASSIGNMENT (( #26937 ) ) ; +#56070 = EDGE_CURVE ( 'NONE', #23198, #74534, #26837, .T. ) ; +#56071 = VERTEX_POINT ( 'NONE', #51316 ) ; +#56072 = EDGE_LOOP ( 'NONE', ( #67651, #49278, #86728, #12094 ) ) ; +#56073 = AXIS2_PLACEMENT_3D ( 'NONE', #41568, #65043, #81887 ) ; +#56074 = VERTEX_POINT ( 'NONE', #28808 ) ; +#56075 = CARTESIAN_POINT ( 'NONE', ( 0.2827097938661469745, -0.9901059572320288771, 0.8299999999999996270 ) ) ; +#56076 = SURFACE_STYLE_FILL_AREA ( #86697 ) ; +#56078 = EDGE_CURVE ( 'NONE', #5565, #84446, #59510, .T. ) ; +#56077 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11858, #43579, #83908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56079 = AXIS2_PLACEMENT_3D ( 'NONE', #97087, #43489, #64974 ) ; +#56080 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56081 = LINE ( 'NONE', #48430, #12107 ) ; +#56082 = PRODUCT_CONTEXT ( 'NONE', #43669, 'mechanical' ) ; +#56083 = SURFACE_STYLE_USAGE ( .BOTH. , #10495 ) ; +#56084 = CARTESIAN_POINT ( 'NONE', ( 1.027503817219263649, -1.458506469577147913, 0.8099999999997017364 ) ) ; +#56086 = ORIENTED_EDGE ( 'NONE', *, *, #84434, .T. ) ; +#56085 = VERTEX_POINT ( 'NONE', #58505 ) ; +#56087 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2316 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39398, #48089, #32267 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56088 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#56089 = ORIENTED_EDGE ( 'NONE', *, *, #41834, .F. ) ; +#56090 = VERTEX_POINT ( 'NONE', #50823 ) ; +#56091 = CARTESIAN_POINT ( 'NONE', ( -0.7465345709966251242, 1.533618350106040085, 0.8299999999999999600 ) ) ; +#56093 = VECTOR ( 'NONE', #89792, 1000.000000000000000 ) ; +#56092 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58815, 'distance_accuracy_value', 'NONE'); +#56094 = SURFACE_STYLE_USAGE ( .BOTH. , #32605 ) ; +#56095 = VERTEX_POINT ( 'NONE', #58996 ) ; +#56096 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82194 ) ) ; +#56097 = EDGE_CURVE ( 'NONE', #60372, #53395, #57997, .T. ) ; +#56098 = PRESENTATION_STYLE_ASSIGNMENT (( #24965 ) ) ; +#56099 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#56101 = VECTOR ( 'NONE', #25388, 1000.000000000000000 ) ; +#56100 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59327 ) ) ; +#56102 = ORIENTED_EDGE ( 'NONE', *, *, #73729, .F. ) ; +#56103 = ORIENTED_EDGE ( 'NONE', *, *, #14048, .F. ) ; +#56104 = SURFACE_STYLE_FILL_AREA ( #55612 ) ; +#56105 = ORIENTED_EDGE ( 'NONE', *, *, #44365, .T. ) ; +#56106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65625 ), #47925 ) ; +#56107 = ORIENTED_EDGE ( 'NONE', *, *, #14736, .T. ) ; +#56108 = CARTESIAN_POINT ( 'NONE', ( 0.3732565376499660248, -1.295998480396600039, 0.8300000000000004041 ) ) ; +#56109 = VECTOR ( 'NONE', #9381, 1000.000000000000000 ) ; +#56110 = CARTESIAN_POINT ( 'NONE', ( -0.1487993745455430117, -1.164662551751850073, 0.8100000000000000533 ) ) ; +#56111 = FILL_AREA_STYLE_COLOUR ( '', #32571 ) ; +#56113 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36587, #98764, #83537, #2039 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#56112 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56115 = VERTEX_POINT ( 'NONE', #36000 ) ; +#56114 = LINE ( 'NONE', #80103, #15152 ) ; +#56116 = VECTOR ( 'NONE', #86326, 1000.000000000000000 ) ; +#56117 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56118 = EDGE_CURVE ( 'NONE', #66285, #22678, #67589, .T. ) ; +#56119 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54947 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52347, #43152, #4352 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56120 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.4245906043549200204, -6.018531076210109988E-33 ) ) ; +#56121 = EDGE_LOOP ( 'NONE', ( #6269, #37442, #724, #84576 ) ) ; +#56123 = PRESENTATION_STYLE_ASSIGNMENT (( #16755 ) ) ; +#56122 = SURFACE_STYLE_USAGE ( .BOTH. , #70918 ) ; +#56124 = ORIENTED_EDGE ( 'NONE', *, *, #10581, .F. ) ; +#56125 = ORIENTED_EDGE ( 'NONE', *, *, #3426, .F. ) ; +#56126 = SURFACE_STYLE_USAGE ( .BOTH. , #41311 ) ; +#56127 = CARTESIAN_POINT ( 'NONE', ( 1.754677333481259982, -1.433486393616560051, 0.8300000000000002931 ) ) ; +#56128 = FILL_AREA_STYLE ('',( #975 ) ) ; +#56129 = VECTOR ( 'NONE', #80197, 1000.000000000000000 ) ; +#56130 = CARTESIAN_POINT ( 'NONE', ( -0.3921422844660710227, -1.185705927526510051, 0.8299999999999999600 ) ) ; +#56131 = AXIS2_PLACEMENT_3D ( 'NONE', #58018, #78932, #26345 ) ; +#56132 = SURFACE_STYLE_FILL_AREA ( #55633 ) ; +#56133 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#56134 = ADVANCED_FACE ( 'NONE', ( #35003 ), #81960, .T. ) ; +#56135 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45304, 'distance_accuracy_value', 'NONE'); +#56136 = PRESENTATION_STYLE_ASSIGNMENT (( #25002 ) ) ; +#56137 = VERTEX_POINT ( 'NONE', #22149 ) ; +#56138 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#56139 = FILL_AREA_STYLE ('',( #80629 ) ) ; +#56140 = ORIENTED_EDGE ( 'NONE', *, *, #61025, .F. ) ; +#56141 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, 0.000000000000000000 ) ) ; +#56142 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56143 = FILL_AREA_STYLE_COLOUR ( '', #12435 ) ; +#56144 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#56145 = SURFACE_SIDE_STYLE ('',( #26009 ) ) ; +#56146 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39868 ) ) ; +#56147 = SURFACE_STYLE_USAGE ( .BOTH. , #40824 ) ; +#56148 = FILL_AREA_STYLE_COLOUR ( '', #25973 ) ; +#56149 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56150 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56151 = FILL_AREA_STYLE_COLOUR ( '', #34900 ) ; +#56152 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72766 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79129, #9578, #17811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56153 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98173 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98367, #80261, #51526 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56154 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56155 = FACE_OUTER_BOUND ( 'NONE', #41020, .T. ) ; +#56156 = SURFACE_STYLE_FILL_AREA ( #9582 ) ; +#56157 = VECTOR ( 'NONE', #7492, 1000.000000000000000 ) ; +#56158 = PRESENTATION_STYLE_ASSIGNMENT (( #93871 ) ) ; +#56159 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56160 = AXIS2_PLACEMENT_3D ( 'NONE', #45649, #77840, #54892 ) ; +#56161 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#56162 = LINE ( 'NONE', #93387, #19282 ) ; +#56163 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100036 ), #82032 ) ; +#56164 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56165 = VECTOR ( 'NONE', #2133, 1000.000000000000000 ) ; +#56166 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93851 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85649, #47351, #69274 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56168 = ORIENTED_EDGE ( 'NONE', *, *, #97463, .T. ) ; +#56167 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77330 ) ) ; +#56169 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56170 = EDGE_CURVE ( 'NONE', #5540, #73059, #26036, .T. ) ; +#56171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39151, 'distance_accuracy_value', 'NONE'); +#56172 = ORIENTED_EDGE ( 'NONE', *, *, #93952, .T. ) ; +#56173 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71060, 'distance_accuracy_value', 'NONE'); +#56174 = SURFACE_STYLE_USAGE ( .BOTH. , #77105 ) ; +#56175 = CARTESIAN_POINT ( 'NONE', ( -0.1450077104042191978, -1.164919038798186257, 0.8166666666666667629 ) ) ; +#56177 = AXIS2_PLACEMENT_3D ( 'NONE', #50769, #11832, #98604 ) ; +#56176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85435 ), #5525 ) ; +#56178 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#56179 = VECTOR ( 'NONE', #40327, 1000.000000000000000 ) ; +#56180 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56181 = SURFACE_STYLE_USAGE ( .BOTH. , #25041 ) ; +#56182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61060 ), #20280 ) ; +#56183 = PRESENTATION_STYLE_ASSIGNMENT (( #88815 ) ) ; +#56184 = ORIENTED_EDGE ( 'NONE', *, *, #14074, .T. ) ; +#56185 = VERTEX_POINT ( 'NONE', #45104 ) ; +#56186 = PLANE ( 'NONE', #25859 ) ; +#56187 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80192, 'distance_accuracy_value', 'NONE'); +#56188 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4046 ), #36652 ) ; +#56189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#56190 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#56191 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#56192 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #685 ) ) ; +#56193 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#56194 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17008 ) ) ; +#56195 = ORIENTED_EDGE ( 'NONE', *, *, #75225, .F. ) ; +#56196 = CARTESIAN_POINT ( 'NONE', ( 11.51556912487501272, 7.437945124875012581, 0.8991599999999999593 ) ) ; +#56197 = EDGE_CURVE ( 'NONE', #74052, #2960, #14944, .T. ) ; +#56198 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#56199 = EDGE_LOOP ( 'NONE', ( #3075, #14198, #89192, #35012 ) ) ; +#56200 = LINE ( 'NONE', #93427, #6008 ) ; +#56201 = ORIENTED_EDGE ( 'NONE', *, *, #63037, .F. ) ; +#56202 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56203 = FACE_OUTER_BOUND ( 'NONE', #33472, .T. ) ; +#56204 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56205 = ADVANCED_FACE ( 'NONE', ( #45582 ), #92567, .F. ) ; +#56206 = EDGE_CURVE ( 'NONE', #65143, #16557, #70109, .T. ) ; +#56207 = FILL_AREA_STYLE_COLOUR ( '', #1242 ) ; +#56208 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56209 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56210 = CARTESIAN_POINT ( 'NONE', ( 3.575241999999999809, 3.169274666666670015, 0.8991599999999999593 ) ) ; +#56211 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6480, #55049, #54545, #7464, #99858, #39196, #14156, #100841, #61700, #31034, #21866, #45317, #85659, #23907, #37703, #45811, #92302, #68801, #76990 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.417957774307038589E-05, 2.786330893872861745E-05, 4.109794397677815674E-05, 5.383676549423571200E-05, 6.625423184903386081E-05, 7.847836201925432608E-05, 9.066284592777046607E-05, 0.0001028204189866484036, 0.0001149859491741200233, 0.0001269720978533767314, 0.0001389625930523584311, 0.0001514642992412946381, 0.0001643130881902067349, 0.0001776669893733621162, 0.0001918024004216863185, 0.0002068227363344061337 ), + .UNSPECIFIED. ) ; +#56212 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56213 = SURFACE_STYLE_FILL_AREA ( #88841 ) ; +#56216 = ORIENTED_EDGE ( 'NONE', *, *, #22902, .F. ) ; +#56215 = EDGE_LOOP ( 'NONE', ( #85050, #9850, #20278, #67218 ) ) ; +#56214 = CONICAL_SURFACE ( 'NONE', #25254, 0.5799999999567262421, 0.7853981633974477239 ) ; +#56217 = LINE ( 'NONE', #87327, #34004 ) ; +#56218 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#56219 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#56220 = ORIENTED_EDGE ( 'NONE', *, *, #89228, .T. ) ; +#56221 = PRESENTATION_STYLE_ASSIGNMENT (( #93937 ) ) ; +#56222 = AXIS2_PLACEMENT_3D ( 'NONE', #51117, #57275, #50128 ) ; +#56224 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56223 = SURFACE_STYLE_FILL_AREA ( #26079 ) ; +#56225 = VERTEX_POINT ( 'NONE', #38989 ) ; +#56226 = ADVANCED_FACE ( 'NONE', ( #15976 ), #47143, .T. ) ; +#56227 = EDGE_LOOP ( 'NONE', ( #7360, #16773, #25947, #79349 ) ) ; +#56228 = EDGE_CURVE ( 'NONE', #27473, #14953, #21650, .T. ) ; +#56229 = FILL_AREA_STYLE_COLOUR ( '', #20480 ) ; +#56230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87178 ), #20330 ) ; +#56231 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57851 ), #25259 ) ; +#56232 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#56233 = FILL_AREA_STYLE ('',( #95478 ) ) ; +#56235 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56234 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56236 = CARTESIAN_POINT ( 'NONE', ( -0.05976542525664269023, 0.3315618930340822890, 0.8100000000000000533 ) ) ; +#56237 = VERTEX_POINT ( 'NONE', #39995 ) ; +#56238 = ORIENTED_EDGE ( 'NONE', *, *, #51194, .F. ) ; +#56239 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56240 = ORIENTED_EDGE ( 'NONE', *, *, #36778, .T. ) ; +#56241 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#56242 = ORIENTED_EDGE ( 'NONE', *, *, #41962, .F. ) ; +#56243 = ADVANCED_FACE ( 'NONE', ( #71653 ), #1717, .F. ) ; +#56244 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000028644, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#56245 = VECTOR ( 'NONE', #31127, 1000.000000000000114 ) ; +#56246 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17055 ), #69199 ) ; +#56247 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56248 = CARTESIAN_POINT ( 'NONE', ( 1.876343683457829981, -1.423344911062679907, 0.8099999999999996092 ) ) ; +#56249 = ORIENTED_EDGE ( 'NONE', *, *, #84620, .T. ) ; +#56251 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.876179938779915179, 0.000000000000000000 ) ) ; +#56250 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10480 ), #46420 ) ; +#56252 = LINE ( 'NONE', #2113, #77028 ) ; +#56253 = ORIENTED_EDGE ( 'NONE', *, *, #68786, .F. ) ; +#56254 = EDGE_CURVE ( 'NONE', #85776, #80455, #64989, .T. ) ; +#56255 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56256 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56257 = FACE_OUTER_BOUND ( 'NONE', #94880, .T. ) ; +#56258 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#56259 = SURFACE_STYLE_FILL_AREA ( #25126 ) ; +#56260 = VECTOR ( 'NONE', #21394, 1000.000000000000227 ) ; +#56261 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2166666666666660079, 0.000000000000000000 ) ) ; +#56263 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666647068, -0.1000000000000000056, 0.000000000000000000 ) ) ; +#56262 = SURFACE_STYLE_USAGE ( .BOTH. , #88385 ) ; +#56264 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56266 = EDGE_CURVE ( 'NONE', #96104, #44430, #63001, .T. ) ; +#56265 = SURFACE_STYLE_FILL_AREA ( #49100 ) ; +#56267 = FACE_OUTER_BOUND ( 'NONE', #35758, .T. ) ; +#56268 = ORIENTED_EDGE ( 'NONE', *, *, #54673, .F. ) ; +#56269 = STYLED_ITEM ( 'NONE', ( #18634 ), #3477 ) ; +#56270 = FACE_OUTER_BOUND ( 'NONE', #12141, .T. ) ; +#56271 = CARTESIAN_POINT ( 'NONE', ( 11.67113275025008789, 7.282382249749913328, 0.8991599999999999593 ) ) ; +#56272 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56274 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56273 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56275 = SURFACE_STYLE_USAGE ( .BOTH. , #47572 ) ; +#56276 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56277 = PRESENTATION_STYLE_ASSIGNMENT (( #61910 ) ) ; +#56278 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#56279 = AXIS2_PLACEMENT_3D ( 'NONE', #55346, #84927, #62486 ) ; +#56280 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56281 = CARTESIAN_POINT ( 'NONE', ( 5.519303750250086793, 9.700686750250087087, 0.8648700000000000276 ) ) ; +#56282 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#56283 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56284 = ORIENTED_EDGE ( 'NONE', *, *, #66316, .T. ) ; +#56285 = EDGE_CURVE ( 'NONE', #54210, #50031, #63506, .T. ) ; +#56286 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56287 = STYLED_ITEM ( 'NONE', ( #83965 ), #29494 ) ; +#56288 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62551, #52863, #84001 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56290 = FILL_AREA_STYLE ('',( #80266 ) ) ; +#56289 = LINE ( 'NONE', #87396, #26331 ) ; +#56291 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56292 = FILL_AREA_STYLE_COLOUR ( '', #98894 ) ; +#56293 = FACE_OUTER_BOUND ( 'NONE', #32187, .T. ) ; +#56294 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74753, #18592, #98149 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56295 = VECTOR ( 'NONE', #58172, 1000.000000000000000 ) ; +#56296 = LINE ( 'NONE', #49125, #52712 ) ; +#56297 = ORIENTED_EDGE ( 'NONE', *, *, #80824, .T. ) ; +#56298 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#56299 = EDGE_CURVE ( 'NONE', #865, #76663, #41519, .T. ) ; +#56300 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56301 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#56302 = CARTESIAN_POINT ( 'NONE', ( -0.1591923701298699756, 0.6899999999999999467, -1.355252715606880543E-17 ) ) ; +#56303 = SURFACE_STYLE_FILL_AREA ( #33303 ) ; +#56304 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30150 ) ) ; +#56305 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97219 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9343, #10847, #12355 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56306 = PRESENTATION_STYLE_ASSIGNMENT (( #48112 ) ) ; +#56307 = FILL_AREA_STYLE ('',( #9723 ) ) ; +#56308 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#56309 = ADVANCED_FACE ( 'NONE', ( #79306 ), #9271, .T. ) ; +#56311 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56310 = AXIS2_PLACEMENT_3D ( 'NONE', #84457, #91609, #99668 ) ; +#56312 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58000 ), #878 ) ; +#56313 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56314 = CARTESIAN_POINT ( 'NONE', ( 0.04906375505614529731, -0.9758031678253580310, 0.8299999999999999600 ) ) ; +#56315 = FILL_AREA_STYLE_COLOUR ( '', #14966 ) ; +#56316 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48548, 'distance_accuracy_value', 'NONE'); +#56317 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56318 = VECTOR ( 'NONE', #26203, 1000.000000000000000 ) ; +#56319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56320 = ORIENTED_EDGE ( 'NONE', *, *, #45610, .T. ) ; +#56321 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56322 = ADVANCED_FACE ( 'NONE', ( #2714 ), #24198, .T. ) ; +#56323 = ORIENTED_EDGE ( 'NONE', *, *, #45560, .F. ) ; +#56324 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33567, 'distance_accuracy_value', 'NONE'); +#56325 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6266, 'distance_accuracy_value', 'NONE'); +#56326 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#56327 = FILL_AREA_STYLE ('',( #84404 ) ) ; +#56328 = FILL_AREA_STYLE_COLOUR ( '', #10074 ) ; +#56329 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.6999999999999990674, 0.1829999999999790128 ) ) ; +#56330 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39787 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95168, #42103, #32930 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56331 = CARTESIAN_POINT ( 'NONE', ( 0.06855147566562069805, -1.423344911062679907, 0.8300000000000004041 ) ) ; +#56332 = FACE_OUTER_BOUND ( 'NONE', #1032, .T. ) ; +#56333 = STYLED_ITEM ( 'NONE', ( #5762 ), #22602 ) ; +#56334 = EDGE_LOOP ( 'NONE', ( #6153, #77483, #85289, #14457 ) ) ; +#56335 = PRESENTATION_STYLE_ASSIGNMENT (( #65450 ) ) ; +#56336 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56337 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.01000000000000000021, -0.2250000000000000333 ) ) ; +#56338 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24329, 'distance_accuracy_value', 'NONE'); +#56340 = STYLED_ITEM ( 'NONE', ( #28006 ), #27226 ) ; +#56339 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73621 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44997, #75189, #44022 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56341 = ORIENTED_EDGE ( 'NONE', *, *, #23068, .F. ) ; +#56342 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#56343 = AXIS2_PLACEMENT_3D ( 'NONE', #55915, #94154, #46697 ) ; +#56344 = FILL_AREA_STYLE_COLOUR ( '', #17846 ) ; +#56345 = CARTESIAN_POINT ( 'NONE', ( 13.17837699999999934, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#56346 = ORIENTED_EDGE ( 'NONE', *, *, #53080, .F. ) ; +#56347 = EDGE_CURVE ( 'NONE', #62323, #37124, #42019, .T. ) ; +#56348 = EDGE_CURVE ( 'NONE', #41478, #55494, #50212, .T. ) ; +#56349 = PRESENTATION_STYLE_ASSIGNMENT (( #47123 ) ) ; +#56350 = SURFACE_STYLE_FILL_AREA ( #95573 ) ; +#56351 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56352 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56353 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#56354 = FACE_OUTER_BOUND ( 'NONE', #28687, .T. ) ; +#56355 = EDGE_LOOP ( 'NONE', ( #83804, #57094, #73833, #78368 ) ) ; +#56356 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56357 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56358 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#56359 = ORIENTED_EDGE ( 'NONE', *, *, #48118, .F. ) ; +#56360 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56361 = PLANE ( 'NONE', #44168 ) ; +#56362 = ADVANCED_FACE ( 'NONE', ( #34875 ), #4694, .F. ) ; +#56363 = ORIENTED_EDGE ( 'NONE', *, *, #66457, .F. ) ; +#56364 = EDGE_CURVE ( 'NONE', #32892, #39861, #27720, .T. ) ; +#56365 = SURFACE_STYLE_USAGE ( .BOTH. , #10766 ) ; +#56366 = CARTESIAN_POINT ( 'NONE', ( 1.798434352155980021, -1.039339352017210061, 0.8300000000000004041 ) ) ; +#56367 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39993 ), #95425 ) ; +#56368 = PRESENTATION_STYLE_ASSIGNMENT (( #95591 ) ) ; +#56369 = SURFACE_STYLE_FILL_AREA ( #94072 ) ; +#56370 = ORIENTED_EDGE ( 'NONE', *, *, #41634, .T. ) ; +#56372 = ORIENTED_EDGE ( 'NONE', *, *, #18804, .F. ) ; +#56371 = ORIENTED_EDGE ( 'NONE', *, *, #1974, .T. ) ; +#56373 = VERTEX_POINT ( 'NONE', #89483 ) ; +#56374 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56375 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51477 ), #38404 ) ; +#56376 = EDGE_LOOP ( 'NONE', ( #84204, #35803, #94438, #59258 ) ) ; +#56378 = ORIENTED_EDGE ( 'NONE', *, *, #48292, .T. ) ; +#56377 = SURFACE_STYLE_FILL_AREA ( #19019 ) ; +#56379 = VECTOR ( 'NONE', #96378, 1000.000000000000000 ) ; +#56380 = AXIS2_PLACEMENT_3D ( 'NONE', #79791, #54807, #85909 ) ; +#56382 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56381 = SURFACE_STYLE_USAGE ( .BOTH. , #9283 ) ; +#56383 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56384 = ORIENTED_EDGE ( 'NONE', *, *, #33260, .T. ) ; +#56385 = LINE ( 'NONE', #86987, #81502 ) ; +#56386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56387 = ORIENTED_EDGE ( 'NONE', *, *, #52211, .F. ) ; +#56388 = SURFACE_STYLE_FILL_AREA ( #1197 ) ; +#56389 = ADVANCED_FACE ( 'NONE', ( #66001 ), #35882, .T. ) ; +#56390 = STYLED_ITEM ( 'NONE', ( #99487 ), #89291 ) ; +#56391 = SURFACE_STYLE_USAGE ( .BOTH. , #96126 ) ; +#56392 = ORIENTED_EDGE ( 'NONE', *, *, #14444, .T. ) ; +#56394 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56393 = VECTOR ( 'NONE', #55620, 1000.000000000000000 ) ; +#56395 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66568 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43116, #35492, #51305 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56396 = EDGE_LOOP ( 'NONE', ( #13622, #18500, #58379, #33517 ) ) ; +#56397 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56398 = EDGE_CURVE ( 'NONE', #53059, #97466, #6147, .T. ) ; +#56399 = SURFACE_STYLE_FILL_AREA ( #65507 ) ; +#56400 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#56401 = VECTOR ( 'NONE', #62367, 999.9999999999998863 ) ; +#56402 = EDGE_CURVE ( 'NONE', #97828, #19800, #92576, .T. ) ; +#56403 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56404 = FILL_AREA_STYLE ('',( #10816 ) ) ; +#56405 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56406 = AXIS2_PLACEMENT_3D ( 'NONE', #25110, #72052, #56247 ) ; +#56407 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56408 = SURFACE_STYLE_FILL_AREA ( #26249 ) ; +#56409 = CARTESIAN_POINT ( 'NONE', ( 0.9994445003280740814, -0.9813977598329840513, 0.8100000000000000533 ) ) ; +#56410 = ORIENTED_EDGE ( 'NONE', *, *, #7792, .T. ) ; +#56411 = FACE_BOUND ( 'NONE', #40298, .T. ) ; +#56412 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10656 ) ) ; +#56413 = SURFACE_STYLE_USAGE ( .BOTH. , #70675 ) ; +#56414 = SURFACE_STYLE_FILL_AREA ( #77833 ) ; +#56415 = VECTOR ( 'NONE', #6028, 1000.000000000000000 ) ; +#56416 = VERTEX_POINT ( 'NONE', #76156 ) ; +#56417 = FILL_AREA_STYLE ('',( #18563 ) ) ; +#56418 = PRESENTATION_STYLE_ASSIGNMENT (( #8811 ) ) ; +#56419 = EDGE_CURVE ( 'NONE', #87853, #12291, #37380, .T. ) ; +#56420 = SURFACE_SIDE_STYLE ('',( #1771 ) ) ; +#56421 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#56422 = CARTESIAN_POINT ( 'NONE', ( 0.2365201132049190025, -1.424034756619420028, 0.8299999999999999600 ) ) ; +#56423 = FILL_AREA_STYLE ('',( #55408 ) ) ; +#56424 = SURFACE_STYLE_USAGE ( .BOTH. , #33935 ) ; +#56425 = PLANE ( 'NONE', #21647 ) ; +#56426 = ORIENTED_EDGE ( 'NONE', *, *, #49075, .T. ) ; +#56427 = EDGE_CURVE ( 'NONE', #51457, #25863, #48625, .T. ) ; +#56428 = PLANE ( 'NONE', #78223 ) ; +#56429 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.149999999999970157, 0.000000000000000000 ) ) ; +#56430 = DIRECTION ( 'NONE', ( 0.7071045084557444627, 0.7071090539100457484, 0.000000000000000000 ) ) ; +#56431 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.05000000000000071, 0.000000000000000000 ) ) ; +#56432 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56433 = LINE ( 'NONE', #17068, #56679 ) ; +#56434 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56435 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#56436 = EDGE_CURVE ( 'NONE', #2124, #52295, #6639, .T. ) ; +#56437 = LINE ( 'NONE', #32919, #55632 ) ; +#56438 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#56439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56440 = PRESENTATION_STYLE_ASSIGNMENT (( #71722 ) ) ; +#56441 = CARTESIAN_POINT ( 'NONE', ( 1.161760760428500072, -1.440849955440170138, 0.8299999999999999600 ) ) ; +#56442 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85749 ), #69403 ) ; +#56443 = LINE ( 'NONE', #87550, #11142 ) ; +#56444 = ORIENTED_EDGE ( 'NONE', *, *, #40988, .F. ) ; +#56445 = ADVANCED_FACE ( 'NONE', ( #21529 ), #84811, .T. ) ; +#56446 = ORIENTED_EDGE ( 'NONE', *, *, #7752, .T. ) ; +#56447 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22019, 'distance_accuracy_value', 'NONE'); +#56448 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6740, 'distance_accuracy_value', 'NONE'); +#56450 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#56449 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93031, #38463, #100602, #8232 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#56451 = CARTESIAN_POINT ( 'NONE', ( 0.1485744800866570237, -1.491420757567720079, 0.8100000000000000533 ) ) ; +#56452 = VECTOR ( 'NONE', #86101, 1000.000000000000000 ) ; +#56453 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000000118, 0.2400000000000000189 ) ) ; +#56454 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59132 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31140, #63328, #79641 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56455 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#56456 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#56457 = SURFACE_STYLE_USAGE ( .BOTH. , #17085 ) ; +#56458 = EDGE_LOOP ( 'NONE', ( #32582, #72160, #90941, #85177 ) ) ; +#56459 = VECTOR ( 'NONE', #70626, 1000.000000000000000 ) ; +#56460 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100306 ) ) ; +#56461 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87887, 'distance_accuracy_value', 'NONE'); +#56462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43363 ), #77614 ) ; +#56464 = SURFACE_STYLE_USAGE ( .BOTH. , #42120 ) ; +#56463 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89099 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40851, #88309, #56691 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56465 = AXIS2_PLACEMENT_3D ( 'NONE', #75426, #43777, #97853 ) ; +#56466 = EDGE_LOOP ( 'NONE', ( #49680, #90783, #49116, #98689 ) ) ; +#56467 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56468 = EDGE_CURVE ( 'NONE', #58647, #76885, #100513, .T. ) ; +#56469 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#56470 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10629 ) ) ; +#56471 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56472 = SURFACE_SIDE_STYLE ('',( #34987 ) ) ; +#56473 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, -0.09999999999999988065, -0.02000000000000000042 ) ) ; +#56474 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43379 ) ) ; +#56475 = VERTEX_POINT ( 'NONE', #68484 ) ; +#56476 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#56477 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54501, 'distance_accuracy_value', 'NONE'); +#56478 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56479 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4546 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #512, #24561, #86809 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56480 = SURFACE_SIDE_STYLE ('',( #17107 ) ) ; +#56481 = FACE_OUTER_BOUND ( 'NONE', #72411, .T. ) ; +#56482 = ORIENTED_EDGE ( 'NONE', *, *, #19505, .T. ) ; +#56483 = ADVANCED_FACE ( 'NONE', ( #92942 ), #23057, .T. ) ; +#56484 = STYLED_ITEM ( 'NONE', ( #44436 ), #99421 ) ; +#56485 = SURFACE_SIDE_STYLE ('',( #33994 ) ) ; +#56486 = FACE_OUTER_BOUND ( 'NONE', #19947, .T. ) ; +#56487 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#56488 = FILL_AREA_STYLE_COLOUR ( '', #61816 ) ; +#56489 = SURFACE_SIDE_STYLE ('',( #8881 ) ) ; +#56490 = ADVANCED_FACE ( 'NONE', ( #48048 ), #17381, .T. ) ; +#56491 = FILL_AREA_STYLE_COLOUR ( '', #92181 ) ; +#56492 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #37013, #82894 ) ; +#56493 = VECTOR ( 'NONE', #26357, 1000.000000000000000 ) ; +#56494 = ORIENTED_EDGE ( 'NONE', *, *, #43249, .T. ) ; +#56496 = ORIENTED_EDGE ( 'NONE', *, *, #1502, .F. ) ; +#56495 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56497 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#56498 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56499 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 10.54921500000000023, 0.8648700000000000276 ) ) ; +#56500 = CARTESIAN_POINT ( 'NONE', ( -0.4123911155665859751, -0.9468660869752939524, 0.8299999999999999600 ) ) ; +#56501 = EDGE_LOOP ( 'NONE', ( #2335, #92076, #61529, #92958 ) ) ; +#56502 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56503 = PRESENTATION_STYLE_ASSIGNMENT (( #84079 ) ) ; +#56504 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56505 = VERTEX_POINT ( 'NONE', #94973 ) ; +#56507 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56506 = PLANE ( 'NONE', #27623 ) ; +#56508 = VERTEX_POINT ( 'NONE', #93944 ) ; +#56509 = ORIENTED_EDGE ( 'NONE', *, *, #8462, .T. ) ; +#56510 = PLANE ( 'NONE', #68919 ) ; +#56512 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#56511 = SURFACE_STYLE_FILL_AREA ( #95737 ) ; +#56513 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6089 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92498, #54238, #60418 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56514 = SURFACE_SIDE_STYLE ('',( #64146 ) ) ; +#56516 = EDGE_CURVE ( 'NONE', #6687, #31320, #79711, .T. ) ; +#56515 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#56517 = ORIENTED_EDGE ( 'NONE', *, *, #10932, .F. ) ; +#56518 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#56519 = VERTEX_POINT ( 'NONE', #62883 ) ; +#56520 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56521 = ORIENTED_EDGE ( 'NONE', *, *, #12430, .T. ) ; +#56522 = EDGE_CURVE ( 'NONE', #68921, #88713, #42984, .T. ) ; +#56523 = ORIENTED_EDGE ( 'NONE', *, *, #85806, .F. ) ; +#56524 = PRESENTATION_STYLE_ASSIGNMENT (( #33527 ) ) ; +#56525 = STYLED_ITEM ( 'NONE', ( #11089 ), #54704 ) ; +#56526 = FILL_AREA_STYLE ('',( #100800 ) ) ; +#56527 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#56528 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63065 ), #27212 ) ; +#56529 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56530 = FILL_AREA_STYLE ('',( #53483 ) ) ; +#56531 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9106 ) ) ; +#56532 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #31336 ) ; +#56533 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56534 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#56535 = EDGE_LOOP ( 'NONE', ( #58447, #36347, #82009, #61270 ) ) ; +#56536 = CARTESIAN_POINT ( 'NONE', ( 1.314898002023040080, -1.423389424083600030, 0.8299999999999994049 ) ) ; +#56537 = EDGE_CURVE ( 'NONE', #20912, #48890, #72518, .T. ) ; +#56538 = SURFACE_SIDE_STYLE ('',( #10426 ) ) ; +#56539 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8991599999999999593 ) ) ; +#56540 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.01500000000000000118, 0.000000000000000000 ) ) ; +#56541 = FACE_OUTER_BOUND ( 'NONE', #51172, .T. ) ; +#56542 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56543 = EDGE_LOOP ( 'NONE', ( #99747, #40416, #45578, #51647 ) ) ; +#56544 = ADVANCED_FACE ( 'NONE', ( #71533 ), #81222, .T. ) ; +#56545 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#56546 = AXIS2_PLACEMENT_3D ( 'NONE', #26741, #11304, #42552 ) ; +#56547 = FILL_AREA_STYLE ('',( #25397 ) ) ; +#56548 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 6.650000000000000355, 0.000000000000000000 ) ) ; +#56549 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35207 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31926, #77874, #85532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56550 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56551 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56552 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11781, 'distance_accuracy_value', 'NONE'); +#56553 = SURFACE_STYLE_FILL_AREA ( #18693 ) ; +#56554 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56555 = FILL_AREA_STYLE ('',( #25407 ) ) ; +#56556 = FILL_AREA_STYLE ('',( #882 ) ) ; +#56557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56558 = VECTOR ( 'NONE', #78808, 1000.000000000000000 ) ; +#56559 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -13.35000000000000142 ) ) ; +#56560 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, -3.500000000000000444, 0.000000000000000000 ) ) ; +#56561 = SURFACE_STYLE_USAGE ( .BOTH. , #77995 ) ; +#56562 = FACE_OUTER_BOUND ( 'NONE', #19813, .T. ) ; +#56563 = EDGE_CURVE ( 'NONE', #25543, #17385, #88858, .T. ) ; +#56565 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#56564 = VECTOR ( 'NONE', #31447, 1000.000000000000000 ) ; +#56567 = EDGE_CURVE ( 'NONE', #85797, #12703, #59265, .T. ) ; +#56566 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56568 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4124, #87879, #18417, #10167 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#56569 = FILL_AREA_STYLE ('',( #93770 ) ) ; +#56570 = ORIENTED_EDGE ( 'NONE', *, *, #94218, .T. ) ; +#56571 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56572 = FILL_AREA_STYLE ('',( #40225 ) ) ; +#56573 = SURFACE_SIDE_STYLE ('',( #25425 ) ) ; +#56574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23061, 'distance_accuracy_value', 'NONE'); +#56576 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56575 = CARTESIAN_POINT ( 'NONE', ( 0.01522189160443420189, -1.319025261726090026, 0.8300000000000002931 ) ) ; +#56577 = STYLED_ITEM ( 'NONE', ( #100924 ), #73798 ) ; +#56578 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#56579 = EDGE_CURVE ( 'NONE', #94260, #42765, #19405, .T. ) ; +#56580 = EDGE_CURVE ( 'NONE', #61021, #48328, #12687, .T. ) ; +#56581 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8648700000000000276 ) ) ; +#56582 = SURFACE_STYLE_USAGE ( .BOTH. , #19226 ) ; +#56583 = VERTEX_POINT ( 'NONE', #49571 ) ; +#56584 = SURFACE_SIDE_STYLE ('',( #25432 ) ) ; +#56585 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56586 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#56587 = EDGE_CURVE ( 'NONE', #70873, #52485, #75058, .T. ) ; +#56588 = ADVANCED_FACE ( 'NONE', ( #89853 ), #35766, .T. ) ; +#56589 = FILL_AREA_STYLE ('',( #25434 ) ) ; +#56590 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10475, 'distance_accuracy_value', 'NONE'); +#56592 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#56591 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44685, #30888, #54400 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56593 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98874 ), #41916 ) ; +#56594 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13997, 'distance_accuracy_value', 'NONE'); +#56595 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56596 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82655 ) ) ; +#56597 = VERTEX_POINT ( 'NONE', #73035 ) ; +#56598 = ORIENTED_EDGE ( 'NONE', *, *, #52928, .T. ) ; +#56599 = EDGE_CURVE ( 'NONE', #27601, #70482, #57755, .T. ) ; +#56600 = SURFACE_STYLE_FILL_AREA ( #24952 ) ; +#56601 = VERTEX_POINT ( 'NONE', #5552 ) ; +#56602 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56603 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59481 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19163, #53837, #46138 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56604 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100451 ), #20698 ) ; +#56606 = SHAPE_DEFINITION_REPRESENTATION ( #32008, #5682 ) ; +#56607 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.416666666666666519, 0.000000000000000000 ) ) ; +#56609 = ORIENTED_EDGE ( 'NONE', *, *, #84354, .T. ) ; +#56608 = ORIENTED_EDGE ( 'NONE', *, *, #79421, .T. ) ; +#56610 = AXIS2_PLACEMENT_3D ( 'NONE', #78720, #39413, #25157 ) ; +#56611 = ORIENTED_EDGE ( 'NONE', *, *, #22532, .F. ) ; +#56612 = VERTEX_POINT ( 'NONE', #15207 ) ; +#56613 = SURFACE_STYLE_FILL_AREA ( #10502 ) ; +#56614 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68816 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75758, #99153, #37478 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56615 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56617 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56616 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56618 = VERTEX_POINT ( 'NONE', #52084 ) ; +#56620 = STYLED_ITEM ( 'NONE', ( #45782 ), #39707 ) ; +#56619 = FILL_AREA_STYLE_COLOUR ( '', #59681 ) ; +#56621 = CARTESIAN_POINT ( 'NONE', ( 5.363740750249974099, 9.545123249750025352, 0.8648700000000000276 ) ) ; +#56622 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51541 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46595, #1149, #16435 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56623 = ORIENTED_EDGE ( 'NONE', *, *, #8462, .F. ) ; +#56624 = EDGE_LOOP ( 'NONE', ( #40419, #32980, #50634, #80324 ) ) ; +#56625 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#56626 = AXIS2_PLACEMENT_3D ( 'NONE', #44463, #83315, #14801 ) ; +#56627 = ORIENTED_EDGE ( 'NONE', *, *, #98861, .F. ) ; +#56628 = ORIENTED_EDGE ( 'NONE', *, *, #81359, .F. ) ; +#56629 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#56630 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69532 ), #28811 ) ; +#56631 = LINE ( 'NONE', #26472, #28265 ) ; +#56632 = CARTESIAN_POINT ( 'NONE', ( 0.9002637987012981347, 0.7099999999999999645, 9.486769009248163798E-17 ) ) ; +#56633 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56635 = ORIENTED_EDGE ( 'NONE', *, *, #96042, .T. ) ; +#56634 = SURFACE_STYLE_USAGE ( .BOTH. , #23974 ) ; +#56636 = LINE ( 'NONE', #95874, #56393 ) ; +#56637 = CARTESIAN_POINT ( 'NONE', ( -0.1330377395154810072, -0.9004049383407729534, 0.8299999999999999600 ) ) ; +#56638 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#56639 = ORIENTED_EDGE ( 'NONE', *, *, #54653, .T. ) ; +#56640 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56641 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 1.399999999999999911, -13.35000000000000142 ) ) ; +#56642 = ORIENTED_EDGE ( 'NONE', *, *, #19533, .F. ) ; +#56643 = ADVANCED_FACE ( 'NONE', ( #22933 ), #95751, .T. ) ; +#56644 = ORIENTED_EDGE ( 'NONE', *, *, #30546, .F. ) ; +#56645 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#56646 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#56647 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41973 ), #4482 ) ; +#56648 = PRESENTATION_STYLE_ASSIGNMENT (( #72941 ) ) ; +#56649 = VECTOR ( 'NONE', #21703, 1000.000000000000000 ) ; +#56650 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#56651 = SURFACE_SIDE_STYLE ('',( #78087 ) ) ; +#56652 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#56653 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000009326, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#56654 = AXIS2_PLACEMENT_3D ( 'NONE', #28022, #50008, #17805 ) ; +#56655 = ORIENTED_EDGE ( 'NONE', *, *, #48399, .F. ) ; +#56656 = SURFACE_STYLE_USAGE ( .BOTH. , #1499 ) ; +#56657 = SURFACE_STYLE_FILL_AREA ( #48979 ) ; +#56658 = ORIENTED_EDGE ( 'NONE', *, *, #33168, .T. ) ; +#56659 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696237999999999913, 0.8991599999999999593 ) ) ; +#56660 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#56661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56662 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12498 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26395, #58066, #74847 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56663 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56664 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#56665 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56666 = FILL_AREA_STYLE ('',( #87262 ) ) ; +#56667 = FILL_AREA_STYLE ('',( #88781 ) ) ; +#56668 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56669 = CARTESIAN_POINT ( 'NONE', ( 0.3533189038523930070, -0.9001815241100280529, 0.8299999999999999600 ) ) ; +#56670 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56671 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000172, 0.8648700000000000276 ) ) ; +#56672 = AXIS2_PLACEMENT_3D ( 'NONE', #72073, #78221, #39393 ) ; +#56673 = LINE ( 'NONE', #17815, #43108 ) ; +#56674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56675 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22909 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79440, #47779, #78918 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56676 = PRESENTATION_STYLE_ASSIGNMENT (( #86262 ) ) ; +#56677 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#56679 = VECTOR ( 'NONE', #77860, 1000.000000000000000 ) ; +#56678 = PRESENTATION_STYLE_ASSIGNMENT (( #32670 ) ) ; +#56680 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#56681 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15195 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72452, #40840, #2529 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56682 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.449999999999999956, -11.36999999999999922 ) ) ; +#56683 = VECTOR ( 'NONE', #39570, 1000.000000000000000 ) ; +#56684 = VECTOR ( 'NONE', #84915, 1000.000000000000114 ) ; +#56685 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74466 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11004, #49404, #9510 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56686 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45705, 'distance_accuracy_value', 'NONE'); +#56687 = EDGE_LOOP ( 'NONE', ( #61726, #67955, #17666, #100388 ) ) ; +#56688 = CLOSED_SHELL ( 'NONE', ( #71116, #51137, #3613, #67477, #95049, #30993 ) ) ; +#56689 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56690 = ORIENTED_EDGE ( 'NONE', *, *, #85835, .F. ) ; +#56692 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53370 ), #6001 ) ; +#56691 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56693 = FILL_AREA_STYLE ('',( #26536 ) ) ; +#56694 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98381 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39847, #54681, #38340 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56695 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56696 = LINE ( 'NONE', #87803, #6741 ) ; +#56697 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81179 ), #12558 ) ; +#56698 = AXIS2_PLACEMENT_3D ( 'NONE', #8525, #47431, #23982 ) ; +#56699 = VERTEX_POINT ( 'NONE', #67850 ) ; +#56700 = VERTEX_POINT ( 'NONE', #76531 ) ; +#56701 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56702 = PRESENTATION_STYLE_ASSIGNMENT (( #41862 ) ) ; +#56703 = PRESENTATION_STYLE_ASSIGNMENT (( #88820 ) ) ; +#56704 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98981 ), #89328 ) ; +#56705 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#56706 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56707 = EDGE_CURVE ( 'NONE', #47130, #605, #61282, .T. ) ; +#56708 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8648700000000000276 ) ) ; +#56709 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56710 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#56711 = ORIENTED_EDGE ( 'NONE', *, *, #87085, .F. ) ; +#56712 = FACE_OUTER_BOUND ( 'NONE', #45599, .T. ) ; +#56713 = VERTEX_POINT ( 'NONE', #60261 ) ; +#56714 = SURFACE_STYLE_USAGE ( .BOTH. , #35113 ) ; +#56715 = ORIENTED_EDGE ( 'NONE', *, *, #89488, .T. ) ; +#56716 = FILL_AREA_STYLE ('',( #64847 ) ) ; +#56717 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90182 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91534, #13873, #14386 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56718 = FILL_AREA_STYLE ('',( #95959 ) ) ; +#56719 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#56720 = FILL_AREA_STYLE ('',( #79688 ) ) ; +#56721 = EDGE_CURVE ( 'NONE', #93318, #56736, #30537, .T. ) ; +#56722 = CARTESIAN_POINT ( 'NONE', ( -1.011710337664210035, -1.062017517080650064, 0.8100000000000000533 ) ) ; +#56723 = CARTESIAN_POINT ( 'NONE', ( 12.44599999999999973, 7.442199999999999704, 0.8991599999999999593 ) ) ; +#56724 = FILL_AREA_STYLE_COLOUR ( '', #44251 ) ; +#56725 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#56726 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#56728 = EDGE_LOOP ( 'NONE', ( #80066, #89550, #28100, #22793 ) ) ; +#56727 = ORIENTED_EDGE ( 'NONE', *, *, #68140, .T. ) ; +#56729 = FILL_AREA_STYLE ('',( #25573 ) ) ; +#56730 = SURFACE_STYLE_FILL_AREA ( #25086 ) ; +#56731 = VERTEX_POINT ( 'NONE', #44367 ) ; +#56732 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40388 ) ) ; +#56735 = CYLINDRICAL_SURFACE ( 'NONE', #26822, 0.1000000000000000472 ) ; +#56734 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#56736 = VERTEX_POINT ( 'NONE', #29083 ) ; +#56737 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80580 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74738, #51263, #4769 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56738 = EDGE_LOOP ( 'NONE', ( #9033, #6885, #38396, #37504 ) ) ; +#56739 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#56740 = FACE_OUTER_BOUND ( 'NONE', #16911, .T. ) ; +#56741 = LINE ( 'NONE', #34762, #30030 ) ; +#56742 = SURFACE_SIDE_STYLE ('',( #33745 ) ) ; +#56743 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52298 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61533, #82495, #75818 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56745 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#56744 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000019873, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#56746 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56747 = EDGE_LOOP ( 'NONE', ( #11269, #55345, #97252, #51129 ) ) ; +#56748 = VERTEX_POINT ( 'NONE', #36254 ) ; +#56749 = ORIENTED_EDGE ( 'NONE', *, *, #73450, .T. ) ; +#56750 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56751 = VECTOR ( 'NONE', #10723, 1000.000000000000000 ) ; +#56752 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19230 ) ) ; +#56754 = ORIENTED_EDGE ( 'NONE', *, *, #39460, .T. ) ; +#56753 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56755 = VECTOR ( 'NONE', #31911, 1000.000000000000000 ) ; +#56756 = SURFACE_STYLE_USAGE ( .BOTH. , #18906 ) ; +#56758 = VECTOR ( 'NONE', #82677, 1000.000000000000000 ) ; +#56757 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#56759 = ORIENTED_EDGE ( 'NONE', *, *, #50805, .T. ) ; +#56760 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.4245906043549200204, -0.01999999999999999695 ) ) ; +#56761 = CLOSED_SHELL ( 'NONE', ( #74787, #57526, #28427, #28971, #15642, #63854 ) ) ; +#56762 = LINE ( 'NONE', #27115, #98171 ) ; +#56763 = ORIENTED_EDGE ( 'NONE', *, *, #12163, .F. ) ; +#56764 = EDGE_CURVE ( 'NONE', #42279, #31335, #59774, .T. ) ; +#56765 = VECTOR ( 'NONE', #7563, 1000.000000000000000 ) ; +#56766 = FILL_AREA_STYLE_COLOUR ( '', #35102 ) ; +#56767 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56768 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#56769 = STYLED_ITEM ( 'NONE', ( #79117 ), #50564 ) ; +#56770 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#56772 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56771 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56773 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.2000000000000000111, -13.40000000000000036 ) ) ; +#56774 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333326642, 0.5000000000000000000, 1.747825839084889375E-76 ) ) ; +#56775 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#56776 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56777 = VERTEX_POINT ( 'NONE', #44865 ) ; +#56778 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#56779 = CARTESIAN_POINT ( 'NONE', ( -0.9526471110344909565, -0.9920916311794309994, 0.8300000000000000711 ) ) ; +#56780 = ORIENTED_EDGE ( 'NONE', *, *, #35142, .F. ) ; +#56781 = LINE ( 'NONE', #24112, #32156 ) ; +#56782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99058 ) ) ; +#56783 = PRESENTATION_STYLE_ASSIGNMENT (( #17413 ) ) ; +#56784 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#56785 = LINE ( 'NONE', #77708, #11952 ) ; +#56786 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.4600000000000000200, 1.129999999999999893 ) ) ; +#56787 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21104 ) ) ; +#56788 = SURFACE_SIDE_STYLE ('',( #32768 ) ) ; +#56789 = ADVANCED_FACE ( 'NONE', ( #91359 ), #21913, .T. ) ; +#56790 = AXIS2_PLACEMENT_3D ( 'NONE', #5460, #76448, #59684 ) ; +#56791 = FACE_OUTER_BOUND ( 'NONE', #66777, .T. ) ; +#56792 = CIRCLE ( 'NONE', #24201, 0.01000000000000002623 ) ; +#56793 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56794 = FILL_AREA_STYLE ('',( #59698 ) ) ; +#56795 = ORIENTED_EDGE ( 'NONE', *, *, #75585, .T. ) ; +#56796 = AXIS2_PLACEMENT_3D ( 'NONE', #44180, #67649, #28868 ) ; +#56797 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#56798 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56799 = LINE ( 'NONE', #17925, #61968 ) ; +#56800 = LINE ( 'NONE', #57295, #28936 ) ; +#56801 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32353 ), #46982 ) ; +#56802 = VECTOR ( 'NONE', #44926, 1000.000000000000000 ) ; +#56803 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56804 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55296, 'distance_accuracy_value', 'NONE'); +#56805 = ORIENTED_EDGE ( 'NONE', *, *, #49914, .T. ) ; +#56806 = EDGE_CURVE ( 'NONE', #37356, #79963, #23430, .T. ) ; +#56807 = STYLED_ITEM ( 'NONE', ( #10589 ), #55333 ) ; +#56808 = SURFACE_STYLE_USAGE ( .BOTH. , #80274 ) ; +#56809 = EDGE_CURVE ( 'NONE', #82810, #74168, #79069, .T. ) ; +#56810 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#56811 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.399999999999999911, -13.54999999999999893 ) ) ; +#56812 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#56813 = LINE ( 'NONE', #95037, #7370 ) ; +#56814 = AXIS2_PLACEMENT_3D ( 'NONE', #2753, #72691, #49739 ) ; +#56815 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, 0.000000000000000000 ) ) ; +#56816 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#56817 = STYLED_ITEM ( 'NONE', ( #64693 ), #24766 ) ; +#56818 = AXIS2_PLACEMENT_3D ( 'NONE', #41722, #80530, #81043 ) ; +#56819 = ORIENTED_EDGE ( 'NONE', *, *, #26019, .F. ) ; +#56820 = ORIENTED_EDGE ( 'NONE', *, *, #15373, .F. ) ; +#56821 = VECTOR ( 'NONE', #92739, 1000.000000000000000 ) ; +#56822 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56823 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30518, 'distance_accuracy_value', 'NONE'); +#56824 = VECTOR ( 'NONE', #21985, 1000.000000000000000 ) ; +#56825 = SURFACE_STYLE_USAGE ( .BOTH. , #39444 ) ; +#56826 = EDGE_CURVE ( 'NONE', #25651, #1862, #100881, .T. ) ; +#56827 = SURFACE_SIDE_STYLE ('',( #17957 ) ) ; +#56828 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68152 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22776, #47261, #77901 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56829 = SURFACE_SIDE_STYLE ('',( #42489 ) ) ; +#56830 = FILL_AREA_STYLE_COLOUR ( '', #50583 ) ; +#56831 = CLOSED_SHELL ( 'NONE', ( #23222, #53938, #23246, #42578, #48208, #60041 ) ) ; +#56832 = VERTEX_POINT ( 'NONE', #9023 ) ; +#56833 = LINE ( 'NONE', #2185, #68900 ) ; +#56834 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, 0.000000000000000000 ) ) ; +#56835 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#56836 = ORIENTED_EDGE ( 'NONE', *, *, #62626, .T. ) ; +#56837 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -1.699999999999999956, -0.02000000000004609896 ) ) ; +#56838 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56839 = ORIENTED_EDGE ( 'NONE', *, *, #68334, .F. ) ; +#56840 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56841 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8648700000000000276 ) ) ; +#56842 = EDGE_CURVE ( 'NONE', #58118, #91380, #54596, .T. ) ; +#56843 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56844 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56845 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56846 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#56847 = VERTEX_POINT ( 'NONE', #93820 ) ; +#56848 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100762 ), #29192 ) ; +#56849 = VERTEX_POINT ( 'NONE', #39754 ) ; +#56850 = CYLINDRICAL_SURFACE ( 'NONE', #39288, 0.05000000000000002359 ) ; +#56851 = ORIENTED_EDGE ( 'NONE', *, *, #82973, .T. ) ; +#56852 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#56853 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#56854 = CARTESIAN_POINT ( 'NONE', ( 1.788364155591040117, -1.009819306370540071, 0.8300000000000004041 ) ) ; +#56855 = ADVANCED_FACE ( 'NONE', ( #42977 ), #28659, .T. ) ; +#56856 = CARTESIAN_POINT ( 'NONE', ( -0.4517732017275800094, -1.126314109036339994, 0.8100000000000000533 ) ) ; +#56857 = SURFACE_STYLE_USAGE ( .BOTH. , #50213 ) ; +#56858 = VECTOR ( 'NONE', #73042, 1000.000000000000000 ) ; +#56859 = LINE ( 'NONE', #25698, #45042 ) ; +#56860 = ORIENTED_EDGE ( 'NONE', *, *, #59732, .T. ) ; +#56862 = VERTEX_POINT ( 'NONE', #26848 ) ; +#56861 = VERTEX_POINT ( 'NONE', #24467 ) ; +#56863 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56864 = ORIENTED_EDGE ( 'NONE', *, *, #47040, .F. ) ; +#56865 = CARTESIAN_POINT ( 'NONE', ( -0.5833333333333330373, 3.099999999999989875, 0.000000000000000000 ) ) ; +#56866 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10087 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20579, #29261, #98606 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56867 = ADVANCED_FACE ( 'NONE', ( #70900 ), #8317, .T. ) ; +#56868 = ORIENTED_EDGE ( 'NONE', *, *, #39591, .T. ) ; +#56869 = STYLED_ITEM ( 'NONE', ( #81723 ), #56544 ) ; +#56871 = ORIENTED_EDGE ( 'NONE', *, *, #61418, .F. ) ; +#56870 = SURFACE_STYLE_USAGE ( .BOTH. , #72161 ) ; +#56872 = VECTOR ( 'NONE', #39452, 1000.000000000000114 ) ; +#56873 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#56875 = FILL_AREA_STYLE_COLOUR ( '', #87350 ) ; +#56874 = LINE ( 'NONE', #8273, #94911 ) ; +#56876 = FILL_AREA_STYLE_COLOUR ( '', #10484 ) ; +#56877 = EDGE_LOOP ( 'NONE', ( #50446, #64995, #75301, #18601 ) ) ; +#56878 = SURFACE_STYLE_FILL_AREA ( #57901 ) ; +#56879 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#56880 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56881 = EDGE_LOOP ( 'NONE', ( #79574, #46647, #60010, #56988 ) ) ; +#56882 = EDGE_CURVE ( 'NONE', #59719, #89490, #2853, .T. ) ; +#56883 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94272 ), #19302 ) ; +#56884 = DIRECTION ( 'NONE', ( -0.7071075504167445569, 0.7071060119555137025, 0.000000000000000000 ) ) ; +#56885 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56886 = EDGE_LOOP ( 'NONE', ( #18047, #51586, #64354, #24363 ) ) ; +#56887 = VECTOR ( 'NONE', #27138, 1000.000000000000000 ) ; +#56888 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999734, 0.6892893218813450629, 0.8000000000000003775 ) ) ; +#56889 = LINE ( 'NONE', #87999, #47864 ) ; +#56891 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671290999999998306, 0.8991599999999999593 ) ) ; +#56890 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608509942, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#56892 = FILL_AREA_STYLE_COLOUR ( '', #48910 ) ; +#56893 = AXIS2_PLACEMENT_3D ( 'NONE', #29366, #29849, #59563 ) ; +#56894 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#56895 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9497, #72350, #33584 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56896 = PRESENTATION_STYLE_ASSIGNMENT (( #17030 ) ) ; +#56897 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88461 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85856, #76683, #53221 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56898 = SURFACE_SIDE_STYLE ('',( #24242 ) ) ; +#56899 = FACE_OUTER_BOUND ( 'NONE', #89745, .T. ) ; +#56900 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#56901 = CARTESIAN_POINT ( 'NONE', ( -0.9354363632813189611, -1.053930089500670020, 0.8100000000000000533 ) ) ; +#56902 = CARTESIAN_POINT ( 'NONE', ( 1.009265655561859987, -0.9654894655288509542, 0.8100000000000000533 ) ) ; +#56903 = EDGE_LOOP ( 'NONE', ( #67625, #41176, #50515, #33864 ) ) ; +#56904 = FACE_BOUND ( 'NONE', #26432, .T. ) ; +#56905 = EDGE_CURVE ( 'NONE', #87953, #16589, #58517, .T. ) ; +#56906 = EDGE_CURVE ( 'NONE', #53854, #87907, #74799, .T. ) ; +#56907 = FILL_AREA_STYLE_COLOUR ( '', #84621 ) ; +#56908 = PLANE ( 'NONE', #85216 ) ; +#56909 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#56910 = LINE ( 'NONE', #20068, #18934 ) ; +#56911 = VERTEX_POINT ( 'NONE', #98684 ) ; +#56912 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#56913 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#56915 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#56914 = SURFACE_STYLE_USAGE ( .BOTH. , #56420 ) ; +#56916 = CARTESIAN_POINT ( 'NONE', ( 1.602494679827060287, -1.010243534007990052, 0.8100000000000000533 ) ) ; +#56917 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16923, 'distance_accuracy_value', 'NONE'); +#56918 = CARTESIAN_POINT ( 'NONE', ( -0.1683685331939580310, -1.436594792639700024, 0.8299999999999999600 ) ) ; +#56919 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100762 ) ) ; +#56920 = PRESENTATION_STYLE_ASSIGNMENT (( #17545 ) ) ; +#56921 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#56922 = PLANE ( 'NONE', #42946 ) ; +#56923 = VERTEX_POINT ( 'NONE', #35016 ) ; +#56924 = LINE ( 'NONE', #51250, #81596 ) ; +#56925 = EDGE_CURVE ( 'NONE', #66265, #89063, #68104, .T. ) ; +#56926 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56927 = ADVANCED_FACE ( 'NONE', ( #82961 ), #35516, .T. ) ; +#56928 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56929 = PRESENTATION_STYLE_ASSIGNMENT (( #15533 ) ) ; +#56930 = VECTOR ( 'NONE', #42941, 1000.000000000000114 ) ; +#56931 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#56932 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#56933 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3038 ) ) ; +#56934 = SURFACE_STYLE_FILL_AREA ( #17565 ) ; +#56935 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #43215, #97312, #64696, #42237 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 1.533293416683374186E-19, 7.071456406524447838E-05 ), + .UNSPECIFIED. ) ; +#56936 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#56937 = SURFACE_SIDE_STYLE ('',( #80403 ) ) ; +#56939 = SURFACE_STYLE_FILL_AREA ( #86024 ) ; +#56938 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29211 ), #71565 ) ; +#56940 = VECTOR ( 'NONE', #50528, 1000.000000000000000 ) ; +#56941 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#56942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56943 = PRESENTATION_STYLE_ASSIGNMENT (( #95673 ) ) ; +#56944 = EDGE_LOOP ( 'NONE', ( #56598, #11551, #96213, #20 ) ) ; +#56945 = LINE ( 'NONE', #63591, #96991 ) ; +#56946 = ORIENTED_EDGE ( 'NONE', *, *, #20128, .F. ) ; +#56947 = VECTOR ( 'NONE', #39497, 1000.000000000000000 ) ; +#56948 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#56949 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56951 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#56950 = AXIS2_PLACEMENT_3D ( 'NONE', #85021, #45188, #264 ) ; +#56952 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#56953 = EDGE_CURVE ( 'NONE', #49837, #64838, #37004, .T. ) ; +#56954 = FILL_AREA_STYLE_COLOUR ( '', #92722 ) ; +#56955 = CARTESIAN_POINT ( 'NONE', ( 1.877470194538120030, -1.043958301690999901, 0.8100000000000000533 ) ) ; +#56956 = LINE ( 'NONE', #34969, #46720 ) ; +#56957 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4850000000000000422, 0.000000000000000000 ) ) ; +#56958 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56959 = VERTEX_POINT ( 'NONE', #60007 ) ; +#56960 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8648700000000000276 ) ) ; +#56961 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56962 = ADVANCED_FACE ( 'NONE', ( #59527 ), #44622, .T. ) ; +#56963 = FILL_AREA_STYLE ('',( #9862 ) ) ; +#56965 = FACE_OUTER_BOUND ( 'NONE', #44627, .T. ) ; +#56964 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#56966 = ORIENTED_EDGE ( 'NONE', *, *, #51733, .F. ) ; +#56967 = FILL_AREA_STYLE_COLOUR ( '', #95682 ) ; +#56968 = SURFACE_STYLE_FILL_AREA ( #3317 ) ; +#56969 = EDGE_CURVE ( 'NONE', #62672, #70050, #69082, .T. ) ; +#56971 = ADVANCED_FACE ( 'NONE', ( #85961 ), #14463, .F. ) ; +#56970 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#56972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6273 ), #22669 ) ; +#56973 = EDGE_LOOP ( 'NONE', ( #44633, #73425, #99288, #17733 ) ) ; +#56974 = SURFACE_SIDE_STYLE ('',( #94698 ) ) ; +#56975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84772 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43109, #82435, #73756 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56976 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10031, 'distance_accuracy_value', 'NONE'); +#56977 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56978 = LINE ( 'NONE', #18097, #71283 ) ; +#56979 = ORIENTED_EDGE ( 'NONE', *, *, #78177, .F. ) ; +#56980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#56981 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#56982 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56983 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52163 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27774, #50763, #76205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#56984 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#56985 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.699999999999999734, 9.720630125846873012E-79 ) ) ; +#56986 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549969999999999182, 0.8991599999999999593 ) ) ; +#56987 = EDGE_CURVE ( 'NONE', #66714, #50104, #74645, .T. ) ; +#56988 = ORIENTED_EDGE ( 'NONE', *, *, #2525, .T. ) ; +#56990 = VERTEX_POINT ( 'NONE', #29815 ) ; +#56989 = LINE ( 'NONE', #66615, #83506 ) ; +#56991 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3608, 'distance_accuracy_value', 'NONE'); +#56992 = FILL_AREA_STYLE_COLOUR ( '', #73543 ) ; +#56993 = FILL_AREA_STYLE ('',( #64129 ) ) ; +#56994 = SURFACE_STYLE_FILL_AREA ( #25841 ) ; +#56995 = ORIENTED_EDGE ( 'NONE', *, *, #86084, .F. ) ; +#56996 = ADVANCED_FACE ( 'NONE', ( #22676 ), #92100, .T. ) ; +#56997 = SURFACE_SIDE_STYLE ('',( #2851 ) ) ; +#56998 = FILL_AREA_STYLE ('',( #80462 ) ) ; +#56999 = PLANE ( 'NONE', #93584 ) ; +#57000 = FILL_AREA_STYLE_COLOUR ( '', #20543 ) ; +#57001 = VECTOR ( 'NONE', #35479, 1000.000000000000000 ) ; +#57003 = ORIENTED_EDGE ( 'NONE', *, *, #60621, .T. ) ; +#57002 = STYLED_ITEM ( 'NONE', ( #95223 ), #75282 ) ; +#57004 = EDGE_CURVE ( 'NONE', #98322, #95720, #13957, .T. ) ; +#57006 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57005 = FILL_AREA_STYLE ('',( #64139 ) ) ; +#57007 = ORIENTED_EDGE ( 'NONE', *, *, #16452, .F. ) ; +#57008 = ORIENTED_EDGE ( 'NONE', *, *, #25922, .F. ) ; +#57009 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86341 ), #84653 ) ; +#57011 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#57010 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#57012 = EDGE_CURVE ( 'NONE', #3550, #64435, #30301, .T. ) ; +#57013 = VERTEX_POINT ( 'NONE', #8275 ) ; +#57014 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2842 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57899, #5679, #96622 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57015 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24431 ), #60295 ) ; +#57016 = AXIS2_PLACEMENT_3D ( 'NONE', #50669, #74128, #89934 ) ; +#57017 = ORIENTED_EDGE ( 'NONE', *, *, #53291, .F. ) ; +#57018 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57019 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57020 = VERTEX_POINT ( 'NONE', #60996 ) ; +#57021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57022 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6330 ), #65084 ) ; +#57023 = CARTESIAN_POINT ( 'NONE', ( -1.362892881570719972, -1.113830263093820161, 0.8100000000000000533 ) ) ; +#57025 = VECTOR ( 'NONE', #87202, 1000.000000000000000 ) ; +#57026 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57027 = CIRCLE ( 'NONE', #4792, 0.01000000000000002623 ) ; +#57028 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57029 = PRESENTATION_STYLE_ASSIGNMENT (( #65153 ) ) ; +#57030 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75345, #54393, #91169, #22733 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57031 = LINE ( 'NONE', #23860, #80520 ) ; +#57033 = EDGE_CURVE ( 'NONE', #73676, #71164, #84451, .T. ) ; +#57032 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, 0.000000000000000000 ) ) ; +#57034 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57035 = CARTESIAN_POINT ( 'NONE', ( 1.224015772021439963, -0.9561532343638800002, 0.8100000000000000533 ) ) ; +#57036 = ORIENTED_EDGE ( 'NONE', *, *, #81449, .T. ) ; +#57037 = LINE ( 'NONE', #18156, #82823 ) ; +#57038 = STYLED_ITEM ( 'NONE', ( #83125 ), #64269 ) ; +#57039 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57040 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14530 ) ) ; +#57041 = FILL_AREA_STYLE_COLOUR ( '', #75318 ) ; +#57042 = SURFACE_STYLE_USAGE ( .BOTH. , #10955 ) ; +#57043 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46442, 'distance_accuracy_value', 'NONE'); +#57044 = FACE_OUTER_BOUND ( 'NONE', #16994, .T. ) ; +#57045 = VECTOR ( 'NONE', #25892, 1000.000000000000000 ) ; +#57046 = FILL_AREA_STYLE_COLOUR ( '', #69064 ) ; +#57047 = LINE ( 'NONE', #48864, #32099 ) ; +#57048 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73842 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96896, #90266, #82135 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57050 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#57051 = VERTEX_POINT ( 'NONE', #23691 ) ; +#57052 = PLANE ( 'NONE', #81464 ) ; +#57053 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, -0.000000000000000000 ) ) ; +#57054 = EDGE_CURVE ( 'NONE', #97577, #36447, #47156, .T. ) ; +#57055 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57056 = FILL_AREA_STYLE ('',( #16164 ) ) ; +#57057 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#57058 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62304, #92397, #39290 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57060 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000000104, -0.2500000000000000000 ) ) ; +#57061 = FACE_OUTER_BOUND ( 'NONE', #13084, .T. ) ; +#57062 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57063 = FILL_AREA_STYLE ('',( #70826 ) ) ; +#57064 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55672, #71471, #64312, #95927 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57065 = FACE_OUTER_BOUND ( 'NONE', #40000, .T. ) ; +#57066 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998900047, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#57067 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57068 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.000000000000000000 ) ) ; +#57069 = LINE ( 'NONE', #41723, #21882 ) ; +#57070 = VECTOR ( 'NONE', #69707, 1000.000000000000000 ) ; +#57071 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#57072 = DIRECTION ( 'NONE', ( -0.7071075504167448900, 0.7071060119555133694, 0.000000000000000000 ) ) ; +#57073 = FACE_OUTER_BOUND ( 'NONE', #43288, .T. ) ; +#57074 = ORIENTED_EDGE ( 'NONE', *, *, #78591, .T. ) ; +#57075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57076 = FACE_OUTER_BOUND ( 'NONE', #31485, .T. ) ; +#57077 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37518 ) ) ; +#57078 = LINE ( 'NONE', #80053, #58643 ) ; +#57079 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#57080 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#57081 = ORIENTED_EDGE ( 'NONE', *, *, #48726, .T. ) ; +#57082 = SURFACE_STYLE_USAGE ( .BOTH. , #80554 ) ; +#57083 = ADVANCED_FACE ( 'NONE', ( #45598 ), #63014, .F. ) ; +#57084 = CARTESIAN_POINT ( 'NONE', ( -0.4294542129446599077, -0.9021127771749032354, 0.8099999999997810063 ) ) ; +#57086 = SURFACE_STYLE_FILL_AREA ( #73394 ) ; +#57085 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54438 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22774, #63107, #37607 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57087 = STYLED_ITEM ( 'NONE', ( #9 ), #92465 ) ; +#57088 = SURFACE_STYLE_FILL_AREA ( #3454 ) ; +#57089 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68474 ), #50599 ) ; +#57090 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57091 = FILL_AREA_STYLE_COLOUR ( '', #25837 ) ; +#57092 = STYLED_ITEM ( 'NONE', ( #94707 ), #6396 ) ; +#57093 = VERTEX_POINT ( 'NONE', #49199 ) ; +#57094 = ORIENTED_EDGE ( 'NONE', *, *, #15744, .F. ) ; +#57095 = FACE_OUTER_BOUND ( 'NONE', #41966, .T. ) ; +#57096 = VERTEX_POINT ( 'NONE', #1191 ) ; +#57097 = SURFACE_STYLE_FILL_AREA ( #24444 ) ; +#57098 = VECTOR ( 'NONE', #59319, 1000.000000000000114 ) ; +#57099 = CARTESIAN_POINT ( 'NONE', ( -0.5238200612200851758, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#57100 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57101 = SHAPE_DEFINITION_REPRESENTATION ( #176, #2465 ) ; +#57102 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57103 = CARTESIAN_POINT ( 'NONE', ( 1.133582523346102322, -1.514066480758920363, 0.8099999999996667643 ) ) ; +#57104 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92872 ), #84819 ) ; +#57106 = ORIENTED_EDGE ( 'NONE', *, *, #63075, .T. ) ; +#57105 = EDGE_LOOP ( 'NONE', ( #70537, #40435, #1480, #70786 ) ) ; +#57107 = ORIENTED_EDGE ( 'NONE', *, *, #92500, .F. ) ; +#57108 = VECTOR ( 'NONE', #71938, 1000.000000000000000 ) ; +#57109 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21208 ), #8069 ) ; +#57110 = ORIENTED_EDGE ( 'NONE', *, *, #36373, .T. ) ; +#57111 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92380, 'distance_accuracy_value', 'NONE'); +#57112 = CARTESIAN_POINT ( 'NONE', ( 1.826147860666869960, -1.473933850988760064, 0.8299999999999999600 ) ) ; +#57113 = CARTESIAN_POINT ( 'NONE', ( 1.414009484217380042, -1.031612284007709990, 0.8299999999999999600 ) ) ; +#57114 = ORIENTED_EDGE ( 'NONE', *, *, #94579, .F. ) ; +#57115 = ADVANCED_FACE ( 'NONE', ( #3227 ), #34393, .T. ) ; +#57116 = LINE ( 'NONE', #72389, #6491 ) ; +#57117 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71969 ) ) ; +#57118 = ORIENTED_EDGE ( 'NONE', *, *, #28271, .T. ) ; +#57119 = FILL_AREA_STYLE ('',( #33105 ) ) ; +#57120 = VECTOR ( 'NONE', #54530, 1000.000000000000114 ) ; +#57121 = VERTEX_POINT ( 'NONE', #72164 ) ; +#57123 = FILL_AREA_STYLE ('',( #49436 ) ) ; +#57122 = LINE ( 'NONE', #88245, #12732 ) ; +#57124 = ORIENTED_EDGE ( 'NONE', *, *, #3903, .F. ) ; +#57125 = VERTEX_POINT ( 'NONE', #24216 ) ; +#57126 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32619 ), #24476 ) ; +#57127 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57128 = FACE_OUTER_BOUND ( 'NONE', #46872, .T. ) ; +#57129 = EDGE_CURVE ( 'NONE', #6530, #8907, #86985, .T. ) ; +#57131 = EDGE_LOOP ( 'NONE', ( #62208, #31987, #37981, #36364 ) ) ; +#57130 = PRESENTATION_STYLE_ASSIGNMENT (( #55117 ) ) ; +#57132 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57133 = ORIENTED_EDGE ( 'NONE', *, *, #10565, .T. ) ; +#57134 = CARTESIAN_POINT ( 'NONE', ( -0.1725832855250629960, -0.9074576374047380600, 0.8299999999999999600 ) ) ; +#57135 = SURFACE_SIDE_STYLE ('',( #67261 ) ) ; +#57136 = ORIENTED_EDGE ( 'NONE', *, *, #93706, .T. ) ; +#57137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57138 = EDGE_LOOP ( 'NONE', ( #85450, #11642, #22310, #64697 ) ) ; +#57139 = EDGE_CURVE ( 'NONE', #53421, #61884, #2732, .T. ) ; +#57140 = ORIENTED_EDGE ( 'NONE', *, *, #6195, .F. ) ; +#57141 = SURFACE_STYLE_FILL_AREA ( #88760 ) ; +#57142 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18 ) ) ; +#57143 = CARTESIAN_POINT ( 'NONE', ( -0.3725126731206029884, -1.137476252684360034, 0.8100000000000000533 ) ) ; +#57144 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, -0.8499999999999997558 ) ) ; +#57145 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -3.183217578417443114E-17, 0.2499999999999998890 ) ) ; +#57147 = EDGE_CURVE ( 'NONE', #13287, #2990, #33889, .T. ) ; +#57146 = PRODUCT ( 'Submodel-SOD882_part_SOD882', 'Submodel-SOD882_part_SOD882', '', ( #45838 ) ) ; +#57148 = ADVANCED_FACE ( 'NONE', ( #88489 ), #18529, .F. ) ; +#57149 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#57150 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#57151 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13010 ), #11403 ) ; +#57152 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74370, 'distance_accuracy_value', 'NONE'); +#57153 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79953 ) ) ; +#57154 = ORIENTED_EDGE ( 'NONE', *, *, #21560, .F. ) ; +#57155 = SURFACE_STYLE_USAGE ( .BOTH. , #89278 ) ; +#57156 = ORIENTED_EDGE ( 'NONE', *, *, #68944, .T. ) ; +#57157 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980549, 0.000000000000000000 ) ) ; +#57158 = CIRCLE ( 'NONE', #31093, 0.1000000000000000472 ) ; +#57159 = EDGE_CURVE ( 'NONE', #36856, #83206, #66508, .T. ) ; +#57160 = EDGE_CURVE ( 'NONE', #23571, #65355, #3718, .T. ) ; +#57161 = PRESENTATION_STYLE_ASSIGNMENT (( #95900 ) ) ; +#57162 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.91999999999999993 ) ) ; +#57163 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76712 ) ) ; +#57164 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8648700000000000276 ) ) ; +#57165 = FACE_OUTER_BOUND ( 'NONE', #71016, .T. ) ; +#57166 = FACE_OUTER_BOUND ( 'NONE', #55412, .T. ) ; +#57167 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72149, #49693, #80326 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57168 = FILL_AREA_STYLE_COLOUR ( '', #83583 ) ; +#57169 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57170 = ADVANCED_FACE ( 'NONE', ( #51712 ), #19025, .T. ) ; +#57171 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#57172 = CARTESIAN_POINT ( 'NONE', ( -1.242030017193550107, -0.9708075278790050389, 0.8299999999999998490 ) ) ; +#57173 = CARTESIAN_POINT ( 'NONE', ( 1.343372187030950737, -1.487199427423351539, 0.8099999999996838618 ) ) ; +#57174 = AXIS2_PLACEMENT_3D ( 'NONE', #72852, #89175, #73855 ) ; +#57175 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#57176 = ADVANCED_FACE ( 'NONE', ( #12302 ), #52223, .T. ) ; +#57177 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8648700000000000276 ) ) ; +#57178 = VECTOR ( 'NONE', #64546, 1000.000000000000000 ) ; +#57179 = FILL_AREA_STYLE ('',( #73489 ) ) ; +#57180 = FILL_AREA_STYLE ('',( #26023 ) ) ; +#57181 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#57182 = VECTOR ( 'NONE', #3775, 1000.000000000000000 ) ; +#57183 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57184 = LINE ( 'NONE', #43331, #78887 ) ; +#57185 = ORIENTED_EDGE ( 'NONE', *, *, #56254, .F. ) ; +#57186 = DIRECTION ( 'NONE', ( -0.7490054809316848417, 0.6625638003500460282, 0.000000000000000000 ) ) ; +#57187 = CARTESIAN_POINT ( 'NONE', ( 1.572445103981990222, -0.9412361261466359874, 0.8100000000000000533 ) ) ; +#57188 = VERTEX_POINT ( 'NONE', #11783 ) ; +#57190 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49178, 'distance_accuracy_value', 'NONE'); +#57189 = PLANE ( 'NONE', #87712 ) ; +#57191 = SURFACE_STYLE_USAGE ( .BOTH. , #95930 ) ; +#57192 = CARTESIAN_POINT ( 'NONE', ( 1.837535075162280318, -0.9500768360162830106, 0.8299999999999999600 ) ) ; +#57193 = CARTESIAN_POINT ( 'NONE', ( 0.1693535484868108343, -1.047148654906014054, 0.8100000000000000533 ) ) ; +#57194 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6700000000000000400, 0.000000000000000000 ) ) ; +#57195 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29629 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32430, #261, #7837 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57196 = LINE ( 'NONE', #73997, #53173 ) ; +#57197 = ORIENTED_EDGE ( 'NONE', *, *, #85778, .T. ) ; +#57198 = EDGE_LOOP ( 'NONE', ( #71610, #58332, #15210, #20396 ) ) ; +#57199 = EDGE_CURVE ( 'NONE', #188, #44836, #77170, .T. ) ; +#57200 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98780, 'distance_accuracy_value', 'NONE'); +#57201 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3322 ), #60414 ) ; +#57202 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#57203 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#57204 = FACE_OUTER_BOUND ( 'NONE', #39958, .T. ) ; +#57205 = SURFACE_STYLE_FILL_AREA ( #97925 ) ; +#57206 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57207 = PRESENTATION_STYLE_ASSIGNMENT (( #40870 ) ) ; +#57208 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#57209 = EDGE_CURVE ( 'NONE', #72032, #70891, #7142, .T. ) ; +#57210 = ORIENTED_EDGE ( 'NONE', *, *, #68909, .T. ) ; +#57211 = FILL_AREA_STYLE ('',( #26555 ) ) ; +#57212 = PRESENTATION_STYLE_ASSIGNMENT (( #24571 ) ) ; +#57213 = EDGE_LOOP ( 'NONE', ( #83, #100028, #30861, #68732 ) ) ; +#57214 = AXIS2_PLACEMENT_3D ( 'NONE', #86617, #72817, #40678 ) ; +#57215 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57216 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#57217 = ORIENTED_EDGE ( 'NONE', *, *, #4581, .F. ) ; +#57218 = LINE ( 'NONE', #84916, #29965 ) ; +#57219 = FACE_OUTER_BOUND ( 'NONE', #46781, .T. ) ; +#57220 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57221 = FILL_AREA_STYLE ('',( #95961 ) ) ; +#57222 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#57223 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#57224 = VECTOR ( 'NONE', #92122, 1000.000000000000000 ) ; +#57225 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86562 ), #84858 ) ; +#57226 = SURFACE_SIDE_STYLE ('',( #3072 ) ) ; +#57227 = PLANE ( 'NONE', #44324 ) ; +#57228 = FILL_AREA_STYLE ('',( #26072 ) ) ; +#57230 = ORIENTED_EDGE ( 'NONE', *, *, #78793, .T. ) ; +#57229 = ORIENTED_EDGE ( 'NONE', *, *, #52346, .F. ) ; +#57231 = VECTOR ( 'NONE', #47812, 1000.000000000000000 ) ; +#57232 = AXIS2_PLACEMENT_3D ( 'NONE', #56218, #8620, #71006 ) ; +#57233 = ORIENTED_EDGE ( 'NONE', *, *, #4619, .F. ) ; +#57234 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#57235 = VECTOR ( 'NONE', #74328, 1000.000000000000000 ) ; +#57237 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#57236 = SURFACE_STYLE_USAGE ( .BOTH. , #2582 ) ; +#57238 = ORIENTED_EDGE ( 'NONE', *, *, #5330, .T. ) ; +#57240 = ADVANCED_FACE ( 'NONE', ( #85329 ), #44998, .T. ) ; +#57239 = EDGE_LOOP ( 'NONE', ( #56201, #75656, #14623, #44880 ) ) ; +#57241 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14737 ) ) ; +#57242 = PRESENTATION_STYLE_ASSIGNMENT (( #24602 ) ) ; +#57243 = DIRECTION ( 'NONE', ( 0.7071045084557395777, 0.7071090539100506334, 0.000000000000000000 ) ) ; +#57244 = PRESENTATION_STYLE_ASSIGNMENT (( #33748 ) ) ; +#57245 = ORIENTED_EDGE ( 'NONE', *, *, #87434, .T. ) ; +#57246 = ORIENTED_EDGE ( 'NONE', *, *, #16748, .T. ) ; +#57247 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999969891, 0.000000000000000000 ) ) ; +#57248 = ORIENTED_EDGE ( 'NONE', *, *, #3367, .T. ) ; +#57249 = SURFACE_STYLE_FILL_AREA ( #26592 ) ; +#57250 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57251 = VECTOR ( 'NONE', #61429, 1000.000000000000000 ) ; +#57252 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27873 ) ) ; +#57253 = EDGE_LOOP ( 'NONE', ( #21519, #11265, #1986, #38139, #32247, #56371 ) ) ; +#57254 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#57255 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#57256 = EDGE_LOOP ( 'NONE', ( #51557, #64717, #31570, #23983 ) ) ; +#57257 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#57258 = VERTEX_POINT ( 'NONE', #61883 ) ; +#57259 = CARTESIAN_POINT ( 'NONE', ( -1.325735931288071434, 0.6599999999999998090, -1.100000000000000089 ) ) ; +#57260 = SURFACE_STYLE_USAGE ( .BOTH. , #87363 ) ; +#57261 = FACE_OUTER_BOUND ( 'NONE', #80971, .T. ) ; +#57263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #151 ) ) ; +#57262 = CARTESIAN_POINT ( 'NONE', ( -0.4143618085515369809, -1.188311688311689984, 0.8099999999999824007 ) ) ; +#57264 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64310 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58370, #95582, #79814 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57265 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57267 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.100000000000000089 ) ) ; +#57266 = LINE ( 'NONE', #39389, #44761 ) ; +#57268 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#57269 = ORIENTED_EDGE ( 'NONE', *, *, #89564, .T. ) ; +#57270 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57271 = CARTESIAN_POINT ( 'NONE', ( -0.9730827514092390551, -0.9588323859052130249, 0.8300000000000000711 ) ) ; +#57272 = ORIENTED_EDGE ( 'NONE', *, *, #28435, .T. ) ; +#57273 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31148 ) ) ; +#57274 = FACE_OUTER_BOUND ( 'NONE', #22405, .T. ) ; +#57275 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57276 = EDGE_CURVE ( 'NONE', #98929, #5198, #7639, .T. ) ; +#57277 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.449999999999999956, -11.41999999999999993 ) ) ; +#57278 = FACE_OUTER_BOUND ( 'NONE', #7461, .T. ) ; +#57279 = PLANE ( 'NONE', #38916 ) ; +#57280 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#57281 = FACE_OUTER_BOUND ( 'NONE', #40782, .T. ) ; +#57282 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#57283 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57284 = SURFACE_STYLE_USAGE ( .BOTH. , #96534 ) ; +#57285 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#57286 = STYLED_ITEM ( 'NONE', ( #98349 ), #86657 ) ; +#57287 = EDGE_CURVE ( 'NONE', #27981, #27113, #68501, .T. ) ; +#57288 = ORIENTED_EDGE ( 'NONE', *, *, #63651, .F. ) ; +#57289 = STYLED_ITEM ( 'NONE', ( #47726 ), #95535 ) ; +#57290 = PLANE ( 'NONE', #84703 ) ; +#57292 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57291 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000001166, 0.8991599999999999593 ) ) ; +#57293 = SURFACE_SIDE_STYLE ('',( #17431 ) ) ; +#57294 = VECTOR ( 'NONE', #18415, 1000.000000000000000 ) ; +#57295 = CARTESIAN_POINT ( 'NONE', ( 2.818155999999999661, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#57296 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31170 ), #18095 ) ; +#57297 = ORIENTED_EDGE ( 'NONE', *, *, #8266, .T. ) ; +#57298 = VECTOR ( 'NONE', #71783, 1000.000000000000000 ) ; +#57299 = PLANE ( 'NONE', #35906 ) ; +#57300 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57301 = LINE ( 'NONE', #41971, #42887 ) ; +#57302 = SURFACE_SIDE_STYLE ('',( #10722 ) ) ; +#57303 = LINE ( 'NONE', #18454, #79537 ) ; +#57304 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57305 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68692 ) ) ; +#57306 = SURFACE_STYLE_FILL_AREA ( #78738 ) ; +#57307 = SURFACE_STYLE_USAGE ( .BOTH. , #26159 ) ; +#57308 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10021, 'distance_accuracy_value', 'NONE'); +#57309 = EDGE_CURVE ( 'NONE', #79695, #7500, #91496, .T. ) ; +#57310 = VECTOR ( 'NONE', #26644, 1000.000000000000000 ) ; +#57311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57312 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29517 ) ) ; +#57313 = ORIENTED_EDGE ( 'NONE', *, *, #83659, .F. ) ; +#57314 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.67582000000000164, 0.8648700000000000276 ) ) ; +#57315 = ORIENTED_EDGE ( 'NONE', *, *, #2017, .T. ) ; +#57316 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49366, 'distance_accuracy_value', 'NONE'); +#57317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2527, 'distance_accuracy_value', 'NONE'); +#57318 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57319 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57320 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57321 = FILL_AREA_STYLE ('',( #41484 ) ) ; +#57322 = CARTESIAN_POINT ( 'NONE', ( 0.4955186371591528416, -1.204989099812753706, 0.8100000000000001643 ) ) ; +#57323 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57324 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -1.899999999999999911, 0.000000000000000000 ) ) ; +#57325 = PLANE ( 'NONE', #94542 ) ; +#57326 = DIRECTION ( 'NONE', ( 1.000000000000000000, 6.179952383168509971E-14, 0.000000000000000000 ) ) ; +#57327 = ADVANCED_FACE ( 'NONE', ( #99559 ), #22553, .T. ) ; +#57328 = ORIENTED_EDGE ( 'NONE', *, *, #92911, .F. ) ; +#57329 = LINE ( 'NONE', #95564, #60798 ) ; +#57330 = CARTESIAN_POINT ( 'NONE', ( 2.676179938779915002, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#57331 = SURFACE_STYLE_USAGE ( .BOTH. , #18984 ) ; +#57332 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57333 = ORIENTED_EDGE ( 'NONE', *, *, #69071, .F. ) ; +#57334 = STYLED_ITEM ( 'NONE', ( #90156 ), #51833 ) ; +#57335 = ORIENTED_EDGE ( 'NONE', *, *, #85988, .F. ) ; +#57336 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57337 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.123820061220055511, 0.000000000000000000 ) ) ; +#57338 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57340 = CARTESIAN_POINT ( 'NONE', ( -0.7453505133853431941, 1.552609075926966176, 0.8299999999999999600 ) ) ; +#57341 = ORIENTED_EDGE ( 'NONE', *, *, #43047, .T. ) ; +#57342 = FILL_AREA_STYLE_COLOUR ( '', #66955 ) ; +#57343 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57344 = ORIENTED_EDGE ( 'NONE', *, *, #41626, .T. ) ; +#57345 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57346 =( BOUNDED_CURVE ( ) B_SPLINE_CURVE ( 3, ( #28380, #96781, #74344, #36057 ), + .UNSPECIFIED., .F., .F. ) + B_SPLINE_CURVE_WITH_KNOTS ( ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + CURVE ( ) GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_CURVE ( ( 1.000000000000000000, 0.8047378541243654926, 0.8047378541243654926, 1.000000000000000000 ) ) + REPRESENTATION_ITEM ( '' ) ); +#57347 = SURFACE_STYLE_FILL_AREA ( #35383 ) ; +#57349 = EDGE_CURVE ( 'NONE', #11778, #11881, #21544, .T. ) ; +#57348 = VERTEX_POINT ( 'NONE', #60395 ) ; +#57350 = PRESENTATION_STYLE_ASSIGNMENT (( #87460 ) ) ; +#57351 = SURFACE_SIDE_STYLE ('',( #88468 ) ) ; +#57352 = CARTESIAN_POINT ( 'NONE', ( 1.762090253802699902, -0.9814610950457449690, 0.8300000000000004041 ) ) ; +#57353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10479 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82259, #41948, #41445 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57354 = STYLED_ITEM ( 'NONE', ( #72501 ), #34045 ) ; +#57355 = SURFACE_STYLE_USAGE ( .BOTH. , #20024 ) ; +#57356 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#57357 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57358 = ORIENTED_EDGE ( 'NONE', *, *, #6110, .F. ) ; +#57360 = VERTEX_POINT ( 'NONE', #563 ) ; +#57359 = ORIENTED_EDGE ( 'NONE', *, *, #9251, .F. ) ; +#57361 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57362 = ADVANCED_FACE ( 'NONE', ( #62900 ), #41419, .F. ) ; +#57363 = ORIENTED_EDGE ( 'NONE', *, *, #33925, .T. ) ; +#57364 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65485 ), #91574 ) ; +#57366 = ORIENTED_EDGE ( 'NONE', *, *, #3725, .F. ) ; +#57367 = ORIENTED_EDGE ( 'NONE', *, *, #98573, .F. ) ; +#57368 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32858 ), #62241 ) ; +#57369 = SURFACE_STYLE_FILL_AREA ( #65008 ) ; +#57371 = SURFACE_STYLE_USAGE ( .BOTH. , #24730 ) ; +#57370 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#57372 = PRESENTATION_STYLE_ASSIGNMENT (( #66507 ) ) ; +#57373 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#57374 = VERTEX_POINT ( 'NONE', #71552 ) ; +#57375 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57376 = FILL_AREA_STYLE_COLOUR ( '', #9205 ) ; +#57377 = ORIENTED_EDGE ( 'NONE', *, *, #17230, .T. ) ; +#57378 = ADVANCED_FACE ( 'NONE', ( #79724 ), #72534, .T. ) ; +#57379 = AXIS2_PLACEMENT_3D ( 'NONE', #44020, #98074, #43014 ) ; +#57380 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000000295, 0.8648700000000000276 ) ) ; +#57381 = EDGE_CURVE ( 'NONE', #35508, #42723, #79332, .T. ) ; +#57382 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57383 = CIRCLE ( 'NONE', #44280, 0.04999999999999969746 ) ; +#57384 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#57386 = DIRECTION ( 'NONE', ( 0.7071062811861712483, 0.7071072811865701802, 0.000000000000000000 ) ) ; +#57385 = PLANE ( 'NONE', #33296 ) ; +#57387 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57388 = VECTOR ( 'NONE', #85053, 1000.000000000000000 ) ; +#57389 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#57390 = STYLED_ITEM ( 'NONE', ( #34010 ), #69890 ) ; +#57391 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#57392 = SURFACE_SIDE_STYLE ('',( #41557 ) ) ; +#57393 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.266666666666653285, 0.000000000000000000 ) ) ; +#57394 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59237 ) ) ; +#57395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57396 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #293 ) ) ; +#57397 = CARTESIAN_POINT ( 'NONE', ( 0.9858795606121630861, -1.017871276266119951, 0.8100000000000000533 ) ) ; +#57398 = ORIENTED_EDGE ( 'NONE', *, *, #43161, .F. ) ; +#57399 = STYLED_ITEM ( 'NONE', ( #30187 ), #46701 ) ; +#57400 = SURFACE_SIDE_STYLE ('',( #74211 ) ) ; +#57401 = LINE ( 'NONE', #19575, #70692 ) ; +#57402 = FILL_AREA_STYLE ('',( #67897 ) ) ; +#57403 = EDGE_CURVE ( 'NONE', #71529, #74052, #12179, .T. ) ; +#57404 = FACE_OUTER_BOUND ( 'NONE', #83885, .T. ) ; +#57405 = ORIENTED_EDGE ( 'NONE', *, *, #24417, .F. ) ; +#57406 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#57408 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57407 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#57409 = CARTESIAN_POINT ( 'NONE', ( 1.617712736099780280, -1.425091422160009946, 0.8099999999999976108 ) ) ; +#57410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47539 ), #65530 ) ; +#57411 = PRESENTATION_STYLE_ASSIGNMENT (( #26268 ) ) ; +#57412 = LINE ( 'NONE', #95147, #94259 ) ; +#57413 = FILL_AREA_STYLE ('',( #42078 ) ) ; +#57414 = SURFACE_STYLE_USAGE ( .BOTH. , #32908 ) ; +#57415 = ORIENTED_EDGE ( 'NONE', *, *, #67300, .T. ) ; +#57416 = LINE ( 'NONE', #90028, #43686 ) ; +#57417 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#57418 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999919746 ) ) ; +#57419 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57420 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#57421 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57422 = AXIS2_PLACEMENT_3D ( 'NONE', #98728, #43177, #19186 ) ; +#57423 = STYLED_ITEM ( 'NONE', ( #24452 ), #34398 ) ; +#57424 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#57425 = PLANE ( 'NONE', #20360 ) ; +#57426 = ADVANCED_FACE ( 'NONE', ( #34779 ), #20935, .T. ) ; +#57427 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #17315, #46635, #86793, #44132, #16730, #82894 ), #33813 ) ; +#57428 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#57429 = SURFACE_STYLE_USAGE ( .BOTH. , #57953 ) ; +#57430 = FILL_AREA_STYLE_COLOUR ( '', #5146 ) ; +#57431 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65549, 'distance_accuracy_value', 'NONE'); +#57432 = STYLED_ITEM ( 'NONE', ( #95806 ), #96147 ) ; +#57433 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57434 = FILL_AREA_STYLE_COLOUR ( '', #55183 ) ; +#57435 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #39722 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #46745 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#57436 = ORIENTED_EDGE ( 'NONE', *, *, #73393, .F. ) ; +#57437 = SURFACE_STYLE_FILL_AREA ( #55927 ) ; +#57439 = ORIENTED_EDGE ( 'NONE', *, *, #95490, .F. ) ; +#57438 = STYLED_ITEM ( 'NONE', ( #26842 ), #58855 ) ; +#57440 = DIRECTION ( 'NONE', ( -0.7071067811865470176, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#57441 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70377, 'distance_accuracy_value', 'NONE'); +#57442 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69843, 'distance_accuracy_value', 'NONE'); +#57443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63341 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58803, #75586, #74603 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57444 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#57445 = PRESENTATION_STYLE_ASSIGNMENT (( #11859 ) ) ; +#57446 = CARTESIAN_POINT ( 'NONE', ( 0.2846257902759590230, -1.272935805450750246, 0.8100000000000000533 ) ) ; +#57447 = SURFACE_STYLE_USAGE ( .BOTH. , #98637 ) ; +#57448 = CARTESIAN_POINT ( 'NONE', ( 1.864400774706999941, -0.9907810524907121330, 0.8299999999999999600 ) ) ; +#57449 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57450 = LINE ( 'NONE', #63598, #11246 ) ; +#57451 = EDGE_CURVE ( 'NONE', #8781, #67952, #12333, .T. ) ; +#57452 = ORIENTED_EDGE ( 'NONE', *, *, #4777, .T. ) ; +#57453 = LINE ( 'NONE', #10873, #27564 ) ; +#57454 = SURFACE_STYLE_FILL_AREA ( #87065 ) ; +#57455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95142, 'distance_accuracy_value', 'NONE'); +#57456 = PRESENTATION_STYLE_ASSIGNMENT (( #88077 ) ) ; +#57457 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#57458 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#57459 = EDGE_LOOP ( 'NONE', ( #77230, #59099, #4575, #24834 ) ) ; +#57460 = SURFACE_STYLE_FILL_AREA ( #3314 ) ; +#57461 = FACE_OUTER_BOUND ( 'NONE', #1070, .T. ) ; +#57462 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#57463 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57464 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57465 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626904202, -0.1434314575050762430 ) ) ; +#57467 = ORIENTED_EDGE ( 'NONE', *, *, #4988, .F. ) ; +#57466 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63929 ), #32955 ) ; +#57468 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57469 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5474, 'distance_accuracy_value', 'NONE'); +#57470 = FILL_AREA_STYLE_COLOUR ( '', #86962 ) ; +#57471 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#57472 = ORIENTED_EDGE ( 'NONE', *, *, #51913, .T. ) ; +#57473 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57474 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57475 = VECTOR ( 'NONE', #11590, 1000.000000000000000 ) ; +#57476 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -11.36999999999999922 ) ) ; +#57478 = FILL_AREA_STYLE ('',( #65606 ) ) ; +#57477 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#57479 = CARTESIAN_POINT ( 'NONE', ( -1.279803590892660381, -1.190413013056344393, 0.8099999999998476197 ) ) ; +#57480 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#57481 = EDGE_CURVE ( 'NONE', #55713, #49745, #97504, .T. ) ; +#57482 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #28614, #44413, #83259, #90393 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57483 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23381, #62703, #32051, #78011 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57484 = AXIS2_PLACEMENT_3D ( 'NONE', #33737, #33226, #64358 ) ; +#57485 = EDGE_LOOP ( 'NONE', ( #72578, #17742, #48685, #25600 ) ) ; +#57487 = ORIENTED_EDGE ( 'NONE', *, *, #15025, .F. ) ; +#57486 = LINE ( 'NONE', #88592, #32931 ) ; +#57488 = PLANE ( 'NONE', #5054 ) ; +#57490 = CYLINDRICAL_SURFACE ( 'NONE', #70958, 1.383445513478990030 ) ; +#57489 = SURFACE_SIDE_STYLE ('',( #87599 ) ) ; +#57491 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70492 ) ) ; +#57492 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57493 = ORIENTED_EDGE ( 'NONE', *, *, #55360, .T. ) ; +#57494 = EDGE_CURVE ( 'NONE', #26314, #93554, #36272, .T. ) ; +#57495 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57496 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57497 = ADVANCED_FACE ( 'NONE', ( #89370 ), #58768, .T. ) ; +#57498 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57499 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#57500 = ORIENTED_EDGE ( 'NONE', *, *, #4096, .T. ) ; +#57501 = EDGE_CURVE ( 'NONE', #29731, #24110, #100899, .T. ) ; +#57503 = LINE ( 'NONE', #88608, #86066 ) ; +#57502 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#57504 = VERTEX_POINT ( 'NONE', #14216 ) ; +#57505 = AXIS2_PLACEMENT_3D ( 'NONE', #88888, #26115, #24626 ) ; +#57506 = VERTEX_POINT ( 'NONE', #69357 ) ; +#57507 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57508 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45210 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49113, #62929, #80258 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57509 = FACE_OUTER_BOUND ( 'NONE', #82213, .T. ) ; +#57510 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57511 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47646 ) ) ; +#57512 = VERTEX_POINT ( 'NONE', #67865 ) ; +#57513 = STYLED_ITEM ( 'NONE', ( #60304 ), #8639 ) ; +#57514 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40908, #18888, #3086, #9151 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57515 = ADVANCED_FACE ( 'NONE', ( #92830 ), #7023, .F. ) ; +#57516 = EDGE_LOOP ( 'NONE', ( #12402, #40787, #37604, #86573, #15249, #51116, #38993, #98332 ) ) ; +#57517 = CARTESIAN_POINT ( 'NONE', ( 1.278904811106269968, -1.437631519369750199, 0.8299999999999999600 ) ) ; +#57518 = SURFACE_STYLE_FILL_AREA ( #65145 ) ; +#57519 = ORIENTED_EDGE ( 'NONE', *, *, #69503, .F. ) ; +#57520 = SURFACE_STYLE_FILL_AREA ( #89140 ) ; +#57522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57521 = SURFACE_STYLE_FILL_AREA ( #67144 ) ; +#57523 = CARTESIAN_POINT ( 'NONE', ( -1.116693831898450062, -1.233317951191559958, 0.8100000000000000533 ) ) ; +#57524 = VECTOR ( 'NONE', #41319, 1000.000000000000000 ) ; +#57526 = ADVANCED_FACE ( 'NONE', ( #98942 ), #68863, .T. ) ; +#57525 = FILL_AREA_STYLE_COLOUR ( '', #95401 ) ; +#57527 = FACE_OUTER_BOUND ( 'NONE', #14087, .T. ) ; +#57528 = VECTOR ( 'NONE', #99279, 1000.000000000000000 ) ; +#57529 = SURFACE_STYLE_FILL_AREA ( #72823 ) ; +#57530 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57531 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.699999999999999956, 0.1829999999999919746 ) ) ; +#57532 = CARTESIAN_POINT ( 'NONE', ( 1.275362369208429936, -0.9706035140527151661, 0.8299999999999999600 ) ) ; +#57533 = EDGE_CURVE ( 'NONE', #55863, #44158, #54085, .T. ) ; +#57534 = AXIS2_PLACEMENT_3D ( 'NONE', #35851, #21995, #99997 ) ; +#57535 = ORIENTED_EDGE ( 'NONE', *, *, #47150, .F. ) ; +#57536 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57537 = EDGE_CURVE ( 'NONE', #20826, #34886, #91375, .T. ) ; +#57538 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #421 ) ) ; +#57539 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57540 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#57541 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000000513, 0.8991599999999999593 ) ) ; +#57542 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57543 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#57544 = LINE ( 'NONE', #65673, #28910 ) ; +#57545 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19965 ), #8433 ) ; +#57546 = CYLINDRICAL_SURFACE ( 'NONE', #58142, 0.05000000000000012768 ) ; +#57547 = FACE_OUTER_BOUND ( 'NONE', #62141, .T. ) ; +#57548 = ORIENTED_EDGE ( 'NONE', *, *, #60439, .T. ) ; +#57549 = FILL_AREA_STYLE ('',( #26393 ) ) ; +#57550 = STYLED_ITEM ( 'NONE', ( #77725 ), #87866 ) ; +#57551 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6106 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67318, #68802, #5500 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57552 = PRESENTATION_STYLE_ASSIGNMENT (( #26396 ) ) ; +#57553 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59994, 'distance_accuracy_value', 'NONE'); +#57554 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57555 = CARTESIAN_POINT ( 'NONE', ( 5.236461499499823979, 9.417844499499826938, 0.8991599999999999593 ) ) ; +#57556 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57557 = CIRCLE ( 'NONE', #85192, 0.1100000000000007222 ) ; +#57558 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#57559 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#57560 = SURFACE_SIDE_STYLE ('',( #11977 ) ) ; +#57561 = EDGE_CURVE ( 'NONE', #80839, #88972, #13192, .T. ) ; +#57562 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57563 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #441 ), #99817 ) ; +#57564 = SURFACE_STYLE_USAGE ( .BOTH. , #47865 ) ; +#57565 = LINE ( 'NONE', #10978, #30023 ) ; +#57566 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57567 = PLANE ( 'NONE', #87856 ) ; +#57568 = AXIS2_PLACEMENT_3D ( 'NONE', #32020, #84629, #45785 ) ; +#57569 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57570 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57571 = ADVANCED_FACE ( 'NONE', ( #75556 ), #31098, .T. ) ; +#57572 = ORIENTED_EDGE ( 'NONE', *, *, #69266, .T. ) ; +#57573 = SURFACE_SIDE_STYLE ('',( #10986 ) ) ; +#57574 = SURFACE_STYLE_USAGE ( .BOTH. , #49910 ) ; +#57575 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71620, 'distance_accuracy_value', 'NONE'); +#57576 = DIRECTION ( 'NONE', ( 0.7071090539100493011, -0.7071045084557410210, 0.000000000000000000 ) ) ; +#57577 = STYLED_ITEM ( 'NONE', ( #75710 ), #18851 ) ; +#57578 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84618, 'distance_accuracy_value', 'NONE'); +#57579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32897, #95643, #7794 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57581 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57580 = LINE ( 'NONE', #59088, #34636 ) ; +#57582 = EDGE_CURVE ( 'NONE', #39738, #32337, #24488, .T. ) ; +#57583 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#57584 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28332 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45883, #16253, #15241 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57585 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#57586 = VECTOR ( 'NONE', #57326, 1000.000000000000000 ) ; +#57587 = FILL_AREA_STYLE_COLOUR ( '', #59217 ) ; +#57588 = FILL_AREA_STYLE ('',( #95307 ) ) ; +#57589 = ORIENTED_EDGE ( 'NONE', *, *, #38914, .F. ) ; +#57590 = SURFACE_STYLE_USAGE ( .BOTH. , #56584 ) ; +#57592 = EDGE_CURVE ( 'NONE', #43775, #15546, #1483, .T. ) ; +#57591 = PLANE ( 'NONE', #99425 ) ; +#57593 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44476 ) ) ; +#57594 = FILL_AREA_STYLE ('',( #42249 ) ) ; +#57595 = VECTOR ( 'NONE', #28998, 1000.000000000000000 ) ; +#57596 = LINE ( 'NONE', #62851, #39051 ) ; +#57597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44685, 'distance_accuracy_value', 'NONE'); +#57598 = SURFACE_SIDE_STYLE ('',( #26426 ) ) ; +#57599 = STYLED_ITEM ( 'NONE', ( #31595 ), #11382 ) ; +#57600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38412, 'distance_accuracy_value', 'NONE'); +#57601 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57602 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#57603 = ORIENTED_EDGE ( 'NONE', *, *, #40744, .T. ) ; +#57604 = ORIENTED_EDGE ( 'NONE', *, *, #62840, .F. ) ; +#57605 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#57606 = CIRCLE ( 'NONE', #49411, 0.009999999999999998473 ) ; +#57607 = ORIENTED_EDGE ( 'NONE', *, *, #26860, .T. ) ; +#57608 = FILL_AREA_STYLE ('',( #51448 ) ) ; +#57609 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57610 = SURFACE_STYLE_FILL_AREA ( #32080 ) ; +#57611 = EDGE_CURVE ( 'NONE', #54997, #4959, #48965, .T. ) ; +#57612 = CYLINDRICAL_SURFACE ( 'NONE', #5583, 0.009999999999999998473 ) ; +#57613 = ADVANCED_FACE ( 'NONE', ( #55122 ), #40792, .F. ) ; +#57614 = PRODUCT_CONTEXT ( 'NONE', #54757, 'mechanical' ) ; +#57615 = FILL_AREA_STYLE ('',( #96345 ) ) ; +#57617 = VERTEX_POINT ( 'NONE', #54616 ) ; +#57616 = VERTEX_POINT ( 'NONE', #40291 ) ; +#57618 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95300 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28479, #83110, #13070 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57619 = ORIENTED_EDGE ( 'NONE', *, *, #5786, .T. ) ; +#57620 = EDGE_LOOP ( 'NONE', ( #70905, #40513, #66298, #100510 ) ) ; +#57621 = SURFACE_SIDE_STYLE ('',( #56613 ) ) ; +#57622 = CARTESIAN_POINT ( 'NONE', ( 0.5312032056918729594, -0.9984395139652609830, 0.8299999999999999600 ) ) ; +#57623 = VERTEX_POINT ( 'NONE', #87745 ) ; +#57624 = VECTOR ( 'NONE', #48539, 1000.000000000000000 ) ; +#57625 = EDGE_CURVE ( 'NONE', #43378, #43745, #71419, .T. ) ; +#57626 = SURFACE_SIDE_STYLE ('',( #18247 ) ) ; +#57627 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57628 = EDGE_CURVE ( 'NONE', #97828, #46722, #71934, .T. ) ; +#57629 = AXIS2_PLACEMENT_3D ( 'NONE', #96769, #88637, #50862 ) ; +#57630 = EDGE_LOOP ( 'NONE', ( #50228, #72154, #22219, #33099 ) ) ; +#57631 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57632 = ORIENTED_EDGE ( 'NONE', *, *, #45047, .F. ) ; +#57633 = EDGE_CURVE ( 'NONE', #99402, #87713, #95366, .T. ) ; +#57635 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57636 = AXIS2_PLACEMENT_3D ( 'NONE', #71632, #54295, #25190 ) ; +#57637 = ORIENTED_EDGE ( 'NONE', *, *, #19673, .F. ) ; +#57638 = ORIENTED_EDGE ( 'NONE', *, *, #51490, .T. ) ; +#57639 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#57641 = SURFACE_STYLE_USAGE ( .BOTH. , #81616 ) ; +#57640 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.494386206516049929E-12 ) ) ; +#57642 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98264 ), #49445 ) ; +#57643 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571430157, 0.6899999999999999467, 0.5000000000000001110 ) ) ; +#57645 = ORIENTED_EDGE ( 'NONE', *, *, #9104, .T. ) ; +#57644 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57646 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#57647 = ORIENTED_EDGE ( 'NONE', *, *, #69919, .T. ) ; +#57648 = CARTESIAN_POINT ( 'NONE', ( -0.2880456131010220022, -1.031932509624869931, 0.8299999999999999600 ) ) ; +#57649 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#57650 = AXIS2_PLACEMENT_3D ( 'NONE', #22218, #7314, #15527 ) ; +#57651 = VECTOR ( 'NONE', #24802, 1000.000000000000000 ) ; +#57652 = VERTEX_POINT ( 'NONE', #34156 ) ; +#57653 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1350000000000000089 ) ) ; +#57654 = EDGE_LOOP ( 'NONE', ( #55588, #98672, #40528, #60506 ) ) ; +#57655 = ORIENTED_EDGE ( 'NONE', *, *, #67469, .F. ) ; +#57657 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 1.099999999999999867 ) ) ; +#57656 = SURFACE_STYLE_USAGE ( .BOTH. , #25486 ) ; +#57658 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57660 = EDGE_CURVE ( 'NONE', #87567, #38666, #89263, .T. ) ; +#57659 = FILL_AREA_STYLE ('',( #97386 ) ) ; +#57661 = AXIS2_PLACEMENT_3D ( 'NONE', #54113, #63805, #15260 ) ; +#57662 = STYLED_ITEM ( 'NONE', ( #95275 ), #35227 ) ; +#57663 = FILL_AREA_STYLE_COLOUR ( '', #87298 ) ; +#57664 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57665 = AXIS2_PLACEMENT_3D ( 'NONE', #60173, #98351, #73459 ) ; +#57666 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#57667 = STYLED_ITEM ( 'NONE', ( #42866 ), #36895 ) ; +#57668 = FILL_AREA_STYLE ('',( #11571 ) ) ; +#57669 = LINE ( 'NONE', #88767, #74722 ) ; +#57670 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57671 = EDGE_CURVE ( 'NONE', #37187, #94205, #11052, .T. ) ; +#57672 = EDGE_LOOP ( 'NONE', ( #81762, #39155, #12055, #842 ) ) ; +#57673 = ORIENTED_EDGE ( 'NONE', *, *, #100682, .T. ) ; +#57674 = ADVANCED_FACE ( 'NONE', ( #81115 ), #96376, .T. ) ; +#57675 = SURFACE_SIDE_STYLE ('',( #78093 ) ) ; +#57676 = VECTOR ( 'NONE', #29865, 1000.000000000000000 ) ; +#57677 = CARTESIAN_POINT ( 'NONE', ( 1.438017692675660042, -1.296821915455180108, 0.8100000000000000533 ) ) ; +#57678 = LINE ( 'NONE', #57162, #64305 ) ; +#57679 = STYLED_ITEM ( 'NONE', ( #38141 ), #11619 ) ; +#57680 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57681 = PRESENTATION_STYLE_ASSIGNMENT (( #56147 ) ) ; +#57682 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57683 = ORIENTED_EDGE ( 'NONE', *, *, #41597, .F. ) ; +#57684 = SURFACE_SIDE_STYLE ('',( #66792 ) ) ; +#57685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57686 = LINE ( 'NONE', #89295, #57475 ) ; +#57687 = STYLED_ITEM ( 'NONE', ( #154 ), #67343 ) ; +#57688 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#57689 = SURFACE_SIDE_STYLE ('',( #18827 ) ) ; +#57691 = ADVANCED_FACE ( 'NONE', ( #3500 ), #59159, .T. ) ; +#57690 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72519, #18891, #10649, #65359 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57692 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 9.949999999999999289, 0.000000000000000000 ) ) ; +#57693 = SURFACE_STYLE_FILL_AREA ( #57180 ) ; +#57694 = LINE ( 'NONE', #79647, #35533 ) ; +#57695 = LINE ( 'NONE', #81162, #56093 ) ; +#57696 = VECTOR ( 'NONE', #32960, 1000.000000000000114 ) ; +#57697 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6694, 'distance_accuracy_value', 'NONE'); +#57698 = VERTEX_POINT ( 'NONE', #90246 ) ; +#57699 = LINE ( 'NONE', #64308, #10002 ) ; +#57700 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57702 = ADVANCED_FACE ( 'NONE', ( #20295 ), #4955, .F. ) ; +#57701 = SURFACE_STYLE_FILL_AREA ( #34708 ) ; +#57703 = VERTEX_POINT ( 'NONE', #84096 ) ; +#57704 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57705 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57706 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#57707 = LINE ( 'NONE', #89318, #68758 ) ; +#57708 = ADVANCED_FACE ( 'NONE', ( #51975 ), #38635, .T. ) ; +#57709 = CARTESIAN_POINT ( 'NONE', ( 1.795940028366769914, -1.028719707420159946, 0.8100000000000006084 ) ) ; +#57710 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11367 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35714, #58203, #3033 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57711 = ORIENTED_EDGE ( 'NONE', *, *, #42455, .F. ) ; +#57712 = VECTOR ( 'NONE', #28132, 1000.000000000000000 ) ; +#57713 = ORIENTED_EDGE ( 'NONE', *, *, #24782, .F. ) ; +#57714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57715 = EDGE_CURVE ( 'NONE', #41801, #58410, #21304, .T. ) ; +#57716 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.5000000000000015543, 0.000000000000000000 ) ) ; +#57717 = SURFACE_SIDE_STYLE ('',( #34224 ) ) ; +#57718 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999951594, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#57719 = FILL_AREA_STYLE_COLOUR ( '', #36349 ) ; +#57720 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57721 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999709359 ) ) ; +#57722 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100190 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89178, #35076, #10444 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57723 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57724 = SURFACE_SIDE_STYLE ('',( #88327 ) ) ; +#57725 = VERTEX_POINT ( 'NONE', #61143 ) ; +#57726 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59327 ), #56036 ) ; +#57727 = STYLED_ITEM ( 'NONE', ( #39559 ), #35377 ) ; +#57728 = FACE_OUTER_BOUND ( 'NONE', #18724, .T. ) ; +#57729 = ORIENTED_EDGE ( 'NONE', *, *, #74286, .T. ) ; +#57730 = CARTESIAN_POINT ( 'NONE', ( -0.1557459988712610044, -1.504992180692799941, 0.8299999999999999600 ) ) ; +#57731 = AXIS2_PLACEMENT_3D ( 'NONE', #96766, #98229, #81525 ) ; +#57732 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57733 = EDGE_CURVE ( 'NONE', #30563, #13016, #40896, .T. ) ; +#57734 = EDGE_CURVE ( 'NONE', #31591, #40572, #57158, .T. ) ; +#57735 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#57736 = STYLED_ITEM ( 'NONE', ( #9872 ), #97044 ) ; +#57737 = CARTESIAN_POINT ( 'NONE', ( -1.046906373037310045, -0.9912247593444889482, 0.8299999999999999600 ) ) ; +#57738 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57739 = SURFACE_STYLE_FILL_AREA ( #9137 ) ; +#57740 = CARTESIAN_POINT ( 'NONE', ( -0.9337505133853429840, 2.302534075926970125, 0.8100000000000000533 ) ) ; +#57742 = EDGE_LOOP ( 'NONE', ( #69363, #54903, #86210, #73998 ) ) ; +#57741 = EDGE_LOOP ( 'NONE', ( #75532, #11173, #11613, #15277 ) ) ; +#57743 = ADVANCED_FACE ( 'NONE', ( #52980 ), #90758, .T. ) ; +#57744 = VECTOR ( 'NONE', #47085, 1000.000000000000000 ) ; +#57745 = EDGE_CURVE ( 'NONE', #3583, #22697, #39645, .T. ) ; +#57746 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57747 = VERTEX_POINT ( 'NONE', #9916 ) ; +#57748 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#57750 = CARTESIAN_POINT ( 'NONE', ( -0.8116130133853438622, 1.464409075926969894, 0.8100000000000001643 ) ) ; +#57749 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57751 = ORIENTED_EDGE ( 'NONE', *, *, #38110, .F. ) ; +#57752 = ORIENTED_EDGE ( 'NONE', *, *, #96754, .F. ) ; +#57753 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.022832238033761717E-16, 0.000000000000000000 ) ) ; +#57754 = ADVANCED_FACE ( 'NONE', ( #24358 ), #63158, .T. ) ; +#57755 = LINE ( 'NONE', #34258, #3051 ) ; +#57756 = VECTOR ( 'NONE', #7605, 1000.000000000000000 ) ; +#57758 = LINE ( 'NONE', #10650, #72704 ) ; +#57757 = FILL_AREA_STYLE_COLOUR ( '', #79100 ) ; +#57759 = VERTEX_POINT ( 'NONE', #23840 ) ; +#57760 = ORIENTED_EDGE ( 'NONE', *, *, #91233, .F. ) ; +#57761 = EDGE_CURVE ( 'NONE', #62116, #13371, #56000, .T. ) ; +#57762 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26977 ) ) ; +#57763 = PLANE ( 'NONE', #38821 ) ; +#57764 = ORIENTED_EDGE ( 'NONE', *, *, #71894, .T. ) ; +#57765 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#57766 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57767 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44643 ) ) ; +#57769 = ORIENTED_EDGE ( 'NONE', *, *, #15009, .F. ) ; +#57768 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57770 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#57771 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 9.061328076764850526E-17, 0.6500000000000000222 ) ) ; +#57772 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57773 = VERTEX_POINT ( 'NONE', #70779 ) ; +#57774 = CARTESIAN_POINT ( 'NONE', ( -0.1052747236373319933, -1.219598171061480052, 0.8299999999999999600 ) ) ; +#57775 = ORIENTED_EDGE ( 'NONE', *, *, #45168, .T. ) ; +#57776 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67537 ), #83830 ) ; +#57777 = STYLED_ITEM ( 'NONE', ( #8685 ), #88485 ) ; +#57778 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57779 = LINE ( 'NONE', #72545, #53129 ) ; +#57780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57781 = PLANE ( 'NONE', #13307 ) ; +#57783 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#57782 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.000000000000000000 ) ) ; +#57784 = CARTESIAN_POINT ( 'NONE', ( 3.843461499499825962, 7.105605499499824340, 0.8991599999999999593 ) ) ; +#57785 = ORIENTED_EDGE ( 'NONE', *, *, #11329, .T. ) ; +#57786 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#57787 = VECTOR ( 'NONE', #93116, 1000.000000000000000 ) ; +#57788 = ORIENTED_EDGE ( 'NONE', *, *, #15224, .T. ) ; +#57789 = EDGE_CURVE ( 'NONE', #15985, #17257, #46776, .T. ) ; +#57790 = SURFACE_STYLE_USAGE ( .BOTH. , #4611 ) ; +#57791 = PRESENTATION_STYLE_ASSIGNMENT (( #89395 ) ) ; +#57792 = LINE ( 'NONE', #35808, #52872 ) ; +#57793 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #900 ), #34965 ) ; +#57794 = AXIS2_PLACEMENT_3D ( 'NONE', #9969, #3905, #95288 ) ; +#57795 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689420, 0.4849999999999999867, 0.2458578643762689697 ) ) ; +#57796 = EDGE_CURVE ( 'NONE', #4203, #96933, #48346, .T. ) ; +#57798 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57797 = CARTESIAN_POINT ( 'NONE', ( 1.313603896932107107, 0.7100000000000000755, -1.079289321881345520 ) ) ; +#57800 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49613 ), #70788 ) ; +#57799 = LINE ( 'NONE', #80760, #1392 ) ; +#57801 = PRESENTATION_STYLE_ASSIGNMENT (( #35318 ) ) ; +#57802 = FILL_AREA_STYLE_COLOUR ( '', #95518 ) ; +#57804 = STYLED_ITEM ( 'NONE', ( #56920 ), #28947 ) ; +#57803 = AXIS2_PLACEMENT_3D ( 'NONE', #54192, #56232, #87342 ) ; +#57805 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57806 = VECTOR ( 'NONE', #46944, 1000.000000000000000 ) ; +#57807 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.4600000000000000200, 0.8000000000000001554 ) ) ; +#57808 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57809 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#57810 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77345 ) ) ; +#57812 = ORIENTED_EDGE ( 'NONE', *, *, #28825, .T. ) ; +#57813 = EDGE_CURVE ( 'NONE', #13660, #81243, #98771, .T. ) ; +#57815 = FILL_AREA_STYLE ('',( #18952 ) ) ; +#57814 = PRESENTATION_STYLE_ASSIGNMENT (( #58315 ) ) ; +#57816 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57817 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#57818 = CIRCLE ( 'NONE', #67505, 0.04999999999999991257 ) ; +#57819 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63426, 'distance_accuracy_value', 'NONE'); +#57820 = ORIENTED_EDGE ( 'NONE', *, *, #38084, .T. ) ; +#57821 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.000000000000000000 ) ) ; +#57822 = PRESENTATION_STYLE_ASSIGNMENT (( #2658 ) ) ; +#57823 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -11.57000000000000028 ) ) ; +#57824 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57825 = LINE ( 'NONE', #97052, #89025 ) ; +#57826 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57827 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#57828 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #89172, #3409, #33560, #12474, #88171, #82027, #26897, #35070, #50888, #58067, #72330, #96295, #3892, #43191, #95786, #19198, #27913, #25897, #88661 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.179344289177029202E-05, 4.223280199157380981E-05, 6.155514909439392451E-05, 7.952707680626719693E-05, 9.653200757605508891E-05, 0.0001125486211447493580, 0.0001277307644114369792, 0.0001419413655221706113, 0.0001556806596934850605, 0.0001690322672106163763, 0.0001820251840212426541, 0.0001948872847722201340, 0.0002079064349490314606, 0.0002216457291203459640, 0.0002358917785941352181, 0.0002511285410802088888 ), + .UNSPECIFIED. ) ; +#57829 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57830 = ORIENTED_EDGE ( 'NONE', *, *, #80887, .F. ) ; +#57831 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 15.09753200000000106, 0.8648700000000000276 ) ) ; +#57832 = ORIENTED_EDGE ( 'NONE', *, *, #56419, .F. ) ; +#57833 = PRESENTATION_STYLE_ASSIGNMENT (( #72603 ) ) ; +#57834 = EDGE_CURVE ( 'NONE', #57348, #35498, #77943, .T. ) ; +#57835 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96734, 'distance_accuracy_value', 'NONE'); +#57836 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57837 = LINE ( 'NONE', #89444, #40010 ) ; +#57838 = SURFACE_STYLE_USAGE ( .BOTH. , #74127 ) ; +#57839 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57840 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.700000000000000178, -1.793208184573746020E-89 ) ) ; +#57841 = FILL_AREA_STYLE ('',( #65969 ) ) ; +#57842 = VECTOR ( 'NONE', #73025, 1000.000000000000000 ) ; +#57843 = FILL_AREA_STYLE ('',( #85410 ) ) ; +#57844 = EDGE_CURVE ( 'NONE', #21309, #37139, #95237, .T. ) ; +#57845 = ORIENTED_EDGE ( 'NONE', *, *, #41316, .F. ) ; +#57846 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#57847 = SURFACE_STYLE_FILL_AREA ( #74138 ) ; +#57848 = EDGE_LOOP ( 'NONE', ( #87469, #84717, #43110, #16704 ) ) ; +#57849 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8991599999999999593 ) ) ; +#57850 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80714 ) ) ; +#57851 = STYLED_ITEM ( 'NONE', ( #3405 ), #88695 ) ; +#57852 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57853 = ORIENTED_EDGE ( 'NONE', *, *, #80318, .F. ) ; +#57854 = VECTOR ( 'NONE', #58339, 1000.000000000000000 ) ; +#57855 = VECTOR ( 'NONE', #73680, 1000.000000000000000 ) ; +#57856 = PLANE ( 'NONE', #84338 ) ; +#57857 = EDGE_CURVE ( 'NONE', #70651, #33110, #17648, .T. ) ; +#57858 = ADVANCED_FACE ( 'NONE', ( #48836 ), #100789, .T. ) ; +#57859 = SURFACE_STYLE_FILL_AREA ( #10749 ) ; +#57860 = SURFACE_STYLE_USAGE ( .BOTH. , #87445 ) ; +#57861 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #19453, #18514 ) ; +#57862 = LINE ( 'NONE', #42506, #29548 ) ; +#57863 = STYLED_ITEM ( 'NONE', ( #10493 ), #76888 ) ; +#57864 = PRESENTATION_STYLE_ASSIGNMENT (( #18991 ) ) ; +#57865 = EDGE_LOOP ( 'NONE', ( #37724, #58106, #21081, #54661 ) ) ; +#57866 = EDGE_CURVE ( 'NONE', #20041, #2971, #97741, .T. ) ; +#57867 = ADVANCED_FACE ( 'NONE', ( #88138 ), #26866, .T. ) ; +#57868 = FILL_AREA_STYLE_COLOUR ( '', #80561 ) ; +#57869 = ORIENTED_EDGE ( 'NONE', *, *, #10653, .F. ) ; +#57870 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30101 ) ) ; +#57871 = AXIS2_PLACEMENT_3D ( 'NONE', #77867, #84516, #22239 ) ; +#57872 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5578, 'distance_accuracy_value', 'NONE'); +#57873 = VECTOR ( 'NONE', #100097, 1000.000000000000000 ) ; +#57874 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#57875 = ORIENTED_EDGE ( 'NONE', *, *, #75439, .T. ) ; +#57876 = ORIENTED_EDGE ( 'NONE', *, *, #94510, .T. ) ; +#57879 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69204 ), #62727 ) ; +#57878 = AXIS2_PLACEMENT_3D ( 'NONE', #26847, #19139, #74798 ) ; +#57877 = CARTESIAN_POINT ( 'NONE', ( 1.657722982825625024, -1.164568096342167847, 0.8100000000000000533 ) ) ; +#57880 = EDGE_CURVE ( 'NONE', #88109, #32846, #82491, .T. ) ; +#57881 = AXIS2_PLACEMENT_3D ( 'NONE', #90800, #45293, #83142 ) ; +#57882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57883 = FILL_AREA_STYLE ('',( #58879 ) ) ; +#57884 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -0.1499999999999999944 ) ) ; +#57886 = SURFACE_STYLE_FILL_AREA ( #12286 ) ; +#57885 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#57887 = VERTEX_POINT ( 'NONE', #58034 ) ; +#57889 = ORIENTED_EDGE ( 'NONE', *, *, #66737, .T. ) ; +#57888 = ORIENTED_EDGE ( 'NONE', *, *, #40203, .T. ) ; +#57890 = EDGE_LOOP ( 'NONE', ( #60246, #98678, #39723, #95857 ) ) ; +#57891 = EDGE_CURVE ( 'NONE', #11229, #23180, #80102, .T. ) ; +#57892 = AXIS2_PLACEMENT_3D ( 'NONE', #72851, #10969, #64683 ) ; +#57893 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59370, #59864, #12782, #75159 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#57894 = ORIENTED_EDGE ( 'NONE', *, *, #31179, .T. ) ; +#57896 = VERTEX_POINT ( 'NONE', #72812 ) ; +#57895 = SURFACE_STYLE_USAGE ( .BOTH. , #79321 ) ; +#57897 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8648700000000000276 ) ) ; +#57898 = SURFACE_SIDE_STYLE ('',( #10270 ) ) ; +#57899 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#57900 = ORIENTED_EDGE ( 'NONE', *, *, #37205, .F. ) ; +#57901 = FILL_AREA_STYLE ('',( #50230 ) ) ; +#57902 = EDGE_LOOP ( 'NONE', ( #77718, #75927, #4956, #37522 ) ) ; +#57903 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57904 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#57905 = LINE ( 'NONE', #15228, #72820 ) ; +#57906 = AXIS2_PLACEMENT_3D ( 'NONE', #60487, #91588, #67103 ) ; +#57907 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#57908 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85146 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78812, #40022, #9792 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57909 = FILL_AREA_STYLE_COLOUR ( '', #19937 ) ; +#57910 = CYLINDRICAL_SURFACE ( 'NONE', #95977, 0.05000000000000012768 ) ; +#57911 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57912 = LINE ( 'NONE', #67023, #50808 ) ; +#57913 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.000000000000000000 ) ) ; +#57914 = STYLED_ITEM ( 'NONE', ( #41694 ), #71528 ) ; +#57915 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#57916 = AXIS2_PLACEMENT_3D ( 'NONE', #50623, #26627, #41942 ) ; +#57917 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57918 = EDGE_CURVE ( 'NONE', #10531, #39373, #10405, .T. ) ; +#57919 = LINE ( 'NONE', #51231, #8586 ) ; +#57920 = SURFACE_STYLE_FILL_AREA ( #26750 ) ; +#57921 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#57922 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27834 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70181, #23746, #77857 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57923 = CARTESIAN_POINT ( 'NONE', ( 1.020577689509359898, -0.9509517096142480197, 0.8299999999999999600 ) ) ; +#57924 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71146 ) ) ; +#57925 = ORIENTED_EDGE ( 'NONE', *, *, #50635, .T. ) ; +#57927 = AXIS2_PLACEMENT_3D ( 'NONE', #7972, #53536, #62714 ) ; +#57926 = CARTESIAN_POINT ( 'NONE', ( -1.241916755955269958, -1.502675929081449979, 0.8300000000000024025 ) ) ; +#57928 = CYLINDRICAL_SURFACE ( 'NONE', #56073, 0.05000000000000012768 ) ; +#57929 = CARTESIAN_POINT ( 'NONE', ( 4.405103135288819693, 1.443705937490903812, -11.91690420651350024 ) ) ; +#57930 = EDGE_LOOP ( 'NONE', ( #10037, #100644, #87308, #13193 ) ) ; +#57931 = FILL_AREA_STYLE_COLOUR ( '', #39981 ) ; +#57933 = LINE ( 'NONE', #73707, #82971 ) ; +#57932 = VECTOR ( 'NONE', #42017, 1000.000000000000000 ) ; +#57934 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#57935 = CARTESIAN_POINT ( 'NONE', ( -0.2361504354203300127, -1.354501511147599979, 0.8299999999999999600 ) ) ; +#57936 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7223 ), #28518 ) ; +#57937 = SURFACE_SIDE_STYLE ('',( #26772 ) ) ; +#57938 = ORIENTED_EDGE ( 'NONE', *, *, #10698, .T. ) ; +#57939 = CARTESIAN_POINT ( 'NONE', ( 5.646583124874956283, 2.700329875125043966, 0.8991599999999999593 ) ) ; +#57940 = EDGE_CURVE ( 'NONE', #21523, #59846, #72289, .T. ) ; +#57941 = FILL_AREA_STYLE ('',( #73238 ) ) ; +#57942 = PRESENTATION_STYLE_ASSIGNMENT (( #88042 ) ) ; +#57944 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #819 ) ) ; +#57943 = STYLED_ITEM ( 'NONE', ( #33378 ), #38501 ) ; +#57945 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#57946 = VECTOR ( 'NONE', #64068, 1000.000000000000000 ) ; +#57947 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8199999999999999512 ) ) ; +#57948 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#57949 = PRESENTATION_STYLE_ASSIGNMENT (( #88047 ) ) ; +#57950 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#57951 = SURFACE_SIDE_STYLE ('',( #56934 ) ) ; +#57952 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#57953 = SURFACE_SIDE_STYLE ('',( #73249 ) ) ; +#57954 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736765574E-18, 0.8199999999999998401, -0.04999999999999998890 ) ) ; +#57955 = FILL_AREA_STYLE_COLOUR ( '', #5010 ) ; +#57956 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#57957 = LINE ( 'NONE', #89062, #24199 ) ; +#57958 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#57959 = ORIENTED_EDGE ( 'NONE', *, *, #33863, .F. ) ; +#57960 = ORIENTED_EDGE ( 'NONE', *, *, #6556, .T. ) ; +#57961 = SURFACE_STYLE_FILL_AREA ( #95679 ) ; +#57962 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2808578643762690286, -0.1500000000000000222 ) ) ; +#57963 = PRESENTATION_STYLE_ASSIGNMENT (( #75256 ) ) ; +#57964 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87278 ), #12209 ) ; +#57965 = FACE_OUTER_BOUND ( 'NONE', #82795, .T. ) ; +#57966 = FILL_AREA_STYLE_COLOUR ( '', #27240 ) ; +#57967 = SURFACE_STYLE_FILL_AREA ( #33966 ) ; +#57968 = SHAPE_REPRESENTATION ( 'Submodel-XTAL3225_part_XTAL3225', ( #68011, #15831 ), #40369 ) ; +#57969 = PLANE ( 'NONE', #3682 ) ; +#57970 = EDGE_LOOP ( 'NONE', ( #2000, #23692, #58654, #35853 ) ) ; +#57971 = FACE_OUTER_BOUND ( 'NONE', #47147, .T. ) ; +#57972 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#57973 = VERTEX_POINT ( 'NONE', #74317 ) ; +#57974 = SURFACE_SIDE_STYLE ('',( #57460 ) ) ; +#57975 = VECTOR ( 'NONE', #79208, 1000.000000000000000 ) ; +#57976 = PLANE ( 'NONE', #72839 ) ; +#57977 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#57978 = VECTOR ( 'NONE', #1091, 1000.000000000000000 ) ; +#57979 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#57980 = FACE_OUTER_BOUND ( 'NONE', #42870, .T. ) ; +#57981 = VECTOR ( 'NONE', #14829, 1000.000000000000000 ) ; +#57982 = SURFACE_SIDE_STYLE ('',( #62106 ) ) ; +#57983 = ORIENTED_EDGE ( 'NONE', *, *, #3525, .T. ) ; +#57984 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#57985 = EDGE_CURVE ( 'NONE', #36490, #45624, #80994, .T. ) ; +#57986 = PRESENTATION_STYLE_ASSIGNMENT (( #27318 ) ) ; +#57987 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#57988 = VECTOR ( 'NONE', #48377, 1000.000000000000000 ) ; +#57989 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#57990 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #866 ), #20464 ) ; +#57991 = ORIENTED_EDGE ( 'NONE', *, *, #97543, .T. ) ; +#57992 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61181 ) ) ; +#57993 = PRESENTATION_STYLE_ASSIGNMENT (( #96717 ) ) ; +#57994 = PLANE ( 'NONE', #24437 ) ; +#57995 = FACE_OUTER_BOUND ( 'NONE', #66064, .T. ) ; +#57996 = PLANE ( 'NONE', #83712 ) ; +#57997 = LINE ( 'NONE', #74783, #81448 ) ; +#57998 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70600 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76286, #48703, #80349 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#57999 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#58000 = STYLED_ITEM ( 'NONE', ( #70865 ), #48409 ) ; +#58001 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74284 ) ) ; +#58002 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#58003 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #27760, #50250 ), + ( #2751, #90008 ), + ( #58916, #81389 ), + ( #11312, #82372 ), + ( #43539, #74708 ), + ( #72689, #50747 ), + ( #35917, #12838 ), + ( #59421, #20561 ), + ( #82861, #22577 ), + ( #6185, #14367 ), + ( #92011, #84363 ), + ( #28722, #67509 ), + ( #59916, #37421 ), + ( #83371, #45508 ), + ( #23097, #45026 ), + ( #75213, #84845 ), + ( #99087, #13852 ), + ( #54235, #22070 ), + ( #37905, #29725 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06481244438064100166, 0.1287210103013690099, 0.1914041334950269957, 0.2543766094645569797, 0.3164535587835590191, 0.3765787110264209869, 0.4366433609708170183, 0.4963802396372439807, 0.5559708634846659558, 0.6154515602174139843, 0.6764889641051079483, 0.7381427634195599774, 0.8007291384104789911, 0.8649102044861449734, 0.9309819797791719642, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#58004 = ADVANCED_FACE ( 'NONE', ( #90123 ), #89136, .T. ) ; +#58005 = ORIENTED_EDGE ( 'NONE', *, *, #10674, .F. ) ; +#58007 = ORIENTED_EDGE ( 'NONE', *, *, #88382, .T. ) ; +#58006 = PLANE ( 'NONE', #13294 ) ; +#58009 = VECTOR ( 'NONE', #13765, 1000.000000000000000 ) ; +#58008 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10789, 'distance_accuracy_value', 'NONE'); +#58010 = PLANE ( 'NONE', #60580 ) ; +#58011 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402590496, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#58012 = CARTESIAN_POINT ( 'NONE', ( -1.383450513385344305, 1.393384075926970223, 0.8100000000000000533 ) ) ; +#58013 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58014 = ORIENTED_EDGE ( 'NONE', *, *, #40638, .T. ) ; +#58015 = CARTESIAN_POINT ( 'NONE', ( 1.227431534468609975, -1.515241174392790047, 0.8299999999999999600 ) ) ; +#58017 = VECTOR ( 'NONE', #50131, 1000.000000000000000 ) ; +#58016 = AXIS2_PLACEMENT_3D ( 'NONE', #95492, #18907, #50100 ) ; +#58018 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#58019 = ORIENTED_EDGE ( 'NONE', *, *, #18715, .F. ) ; +#58021 = SURFACE_STYLE_USAGE ( .BOTH. , #89124 ) ; +#58020 = LINE ( 'NONE', #36022, #35793 ) ; +#58022 = VERTEX_POINT ( 'NONE', #98218 ) ; +#58023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51669 ), #13891 ) ; +#58024 = ORIENTED_EDGE ( 'NONE', *, *, #38526, .T. ) ; +#58025 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58026 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#58027 = EDGE_CURVE ( 'NONE', #5584, #26980, #75313, .T. ) ; +#58028 = LINE ( 'NONE', #50846, #56493 ) ; +#58029 = FILL_AREA_STYLE_COLOUR ( '', #57150 ) ; +#58030 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58031 = ORIENTED_EDGE ( 'NONE', *, *, #16107, .F. ) ; +#58032 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48871 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86983, #87985, #73185 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58033 = CIRCLE ( 'NONE', #46514, 0.009999999999999998473 ) ; +#58034 = CARTESIAN_POINT ( 'NONE', ( -0.9938630133853425530, 2.355709075926969653, 0.8100000000000000533 ) ) ; +#58035 = ORIENTED_EDGE ( 'NONE', *, *, #36628, .F. ) ; +#58036 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.1200000000000003147, 0.2999999999999999889 ) ) ; +#58037 = VERTEX_POINT ( 'NONE', #62401 ) ; +#58038 = EDGE_CURVE ( 'NONE', #43157, #54213, #54754, .T. ) ; +#58040 = SURFACE_STYLE_USAGE ( .BOTH. , #50855 ) ; +#58039 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8648700000000000276 ) ) ; +#58041 = CARTESIAN_POINT ( 'NONE', ( -0.9900897613018839749, -1.321802795360440319, 0.8299999999999999600 ) ) ; +#58042 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9495 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74955, #65268, #25997 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58043 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 7.018111866568259778E-13 ) ) ; +#58044 = FILL_AREA_STYLE_COLOUR ( '', #10252 ) ; +#58045 = ORIENTED_EDGE ( 'NONE', *, *, #20302, .T. ) ; +#58046 = LINE ( 'NONE', #35054, #86012 ) ; +#58048 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58047 = FILL_AREA_STYLE_COLOUR ( '', #69177 ) ; +#58049 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #47469 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #89226 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#58051 = SURFACE_SIDE_STYLE ('',( #20704 ) ) ; +#58050 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82070, 'distance_accuracy_value', 'NONE'); +#58053 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58054 = VECTOR ( 'NONE', #43974, 1000.000000000000000 ) ; +#58055 = PRESENTATION_STYLE_ASSIGNMENT (( #10431 ) ) ; +#58056 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#58057 = VERTEX_POINT ( 'NONE', #36034 ) ; +#58058 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#58059 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#58060 = EDGE_CURVE ( 'NONE', #40659, #21763, #37025, .T. ) ; +#58061 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58062 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66116 ) ) ; +#58064 = LINE ( 'NONE', #97774, #49742 ) ; +#58063 = AXIS2_PLACEMENT_3D ( 'NONE', #51657, #68910, #37814 ) ; +#58065 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58066 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58067 = CARTESIAN_POINT ( 'NONE', ( 0.4292069872566470767, -1.170408502478720081, 0.8300000000000015143 ) ) ; +#58068 = CIRCLE ( 'NONE', #7352, 0.1499999999999999944 ) ; +#58070 = STYLED_ITEM ( 'NONE', ( #48025 ), #48869 ) ; +#58069 = SURFACE_STYLE_FILL_AREA ( #65686 ) ; +#58071 = ADVANCED_FACE ( 'NONE', ( #23089 ), #99205, .T. ) ; +#58072 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58073 = FACE_OUTER_BOUND ( 'NONE', #20262, .T. ) ; +#58074 = SURFACE_SIDE_STYLE ('',( #13493 ) ) ; +#58075 = LINE ( 'NONE', #97303, #87959 ) ; +#58076 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58077 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58078 = FILL_AREA_STYLE_COLOUR ( '', #38152 ) ; +#58079 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58080 = SURFACE_STYLE_USAGE ( .BOTH. , #26912 ) ; +#58082 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58081 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58083 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58084 = VECTOR ( 'NONE', #68452, 1000.000000000000114 ) ; +#58085 = PLANE ( 'NONE', #85799 ) ; +#58086 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58087 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58088 = EDGE_CURVE ( 'NONE', #10911, #39930, #68127, .T. ) ; +#58089 = ORIENTED_EDGE ( 'NONE', *, *, #15528, .T. ) ; +#58090 = PLANE ( 'NONE', #81289 ) ; +#58091 = EDGE_CURVE ( 'NONE', #81497, #45276, #5322, .T. ) ; +#58092 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22172 ), #31953 ) ; +#58093 = VECTOR ( 'NONE', #69422, 1000.000000000000227 ) ; +#58094 = STYLED_ITEM ( 'NONE', ( #5086 ), #4759 ) ; +#58095 = SURFACE_STYLE_USAGE ( .BOTH. , #17716 ) ; +#58096 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58097 = VERTEX_POINT ( 'NONE', #90641 ) ; +#58098 = LINE ( 'NONE', #17221, #83052 ) ; +#58099 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58100 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9068 ) ) ; +#58101 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -1.012211148232466841E-16, -0.8499999999999999778 ) ) ; +#58102 = SURFACE_STYLE_USAGE ( .BOTH. , #49921 ) ; +#58103 = ADVANCED_FACE ( 'NONE', ( #60026 ), #13447, .F. ) ; +#58104 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2399999999999999911 ) ) ; +#58105 = ORIENTED_EDGE ( 'NONE', *, *, #17983, .T. ) ; +#58106 = ORIENTED_EDGE ( 'NONE', *, *, #50298, .F. ) ; +#58107 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#58108 = ORIENTED_EDGE ( 'NONE', *, *, #54215, .T. ) ; +#58109 = CARTESIAN_POINT ( 'NONE', ( 1.711221411465380093, -1.219829592979950084, 0.8299999999999999600 ) ) ; +#58110 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88200 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39146, #39655, #94252 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58111 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58112 = CARTESIAN_POINT ( 'NONE', ( -1.272737459667760085, -0.9076590548536880299, 0.8299999999999997380 ) ) ; +#58113 = EDGE_CURVE ( 'NONE', #25944, #28972, #40431, .T. ) ; +#58114 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #84437, #58257 ) ; +#58115 = SURFACE_SIDE_STYLE ('',( #89715 ) ) ; +#58116 = VECTOR ( 'NONE', #69773, 1000.000000000000000 ) ; +#58118 = VERTEX_POINT ( 'NONE', #56775 ) ; +#58117 = ORIENTED_EDGE ( 'NONE', *, *, #50364, .F. ) ; +#58119 = VERTEX_POINT ( 'NONE', #87876 ) ; +#58120 = ORIENTED_EDGE ( 'NONE', *, *, #97383, .T. ) ; +#58121 = LINE ( 'NONE', #17244, #26285 ) ; +#58122 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54898 ), #35314 ) ; +#58123 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20604 ) ) ; +#58124 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4198, 'distance_accuracy_value', 'NONE'); +#58125 = FACE_OUTER_BOUND ( 'NONE', #41274, .T. ) ; +#58126 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1458578643762690197 ) ) ; +#58127 = ORIENTED_EDGE ( 'NONE', *, *, #35730, .F. ) ; +#58128 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22220 ) ) ; +#58129 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#58130 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61715 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81976, #68112, #59023 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58131 = VERTEX_POINT ( 'NONE', #63906 ) ; +#58132 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58133 = ORIENTED_EDGE ( 'NONE', *, *, #21093, .T. ) ; +#58134 = VECTOR ( 'NONE', #74537, 1000.000000000000000 ) ; +#58136 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#58135 = FILL_AREA_STYLE_COLOUR ( '', #58546 ) ; +#58137 = ORIENTED_EDGE ( 'NONE', *, *, #82163, .T. ) ; +#58138 = EDGE_LOOP ( 'NONE', ( #7372, #42356, #86363, #54852 ) ) ; +#58139 = EDGE_CURVE ( 'NONE', #30014, #30288, #17408, .T. ) ; +#58140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22234 ) ) ; +#58141 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#58142 = AXIS2_PLACEMENT_3D ( 'NONE', #88650, #63189, #9948 ) ; +#58143 = SURFACE_STYLE_USAGE ( .BOTH. , #65776 ) ; +#58145 = ORIENTED_EDGE ( 'NONE', *, *, #90253, .T. ) ; +#58144 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58146 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.4866665961941922802, 0.6665916412559034221 ) ) ; +#58147 = ORIENTED_EDGE ( 'NONE', *, *, #28305, .F. ) ; +#58148 = SURFACE_STYLE_USAGE ( .BOTH. , #51485 ) ; +#58149 = VERTEX_POINT ( 'NONE', #1621 ) ; +#58152 = FILL_AREA_STYLE_COLOUR ( '', #56771 ) ; +#58151 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82471 ), #12465 ) ; +#58150 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58153 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.000000000000000000 ) ) ; +#58154 = ORIENTED_EDGE ( 'NONE', *, *, #15175, .T. ) ; +#58155 = ORIENTED_EDGE ( 'NONE', *, *, #42684, .T. ) ; +#58156 = EDGE_CURVE ( 'NONE', #69886, #69086, #71567, .T. ) ; +#58158 = PRESENTATION_STYLE_ASSIGNMENT (( #28483 ) ) ; +#58157 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#58159 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5238200612200850648, -0.02000000000000000042 ) ) ; +#58160 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28726 ) ) ; +#58161 = STYLED_ITEM ( 'NONE', ( #59083 ), #99573 ) ; +#58162 = SURFACE_STYLE_FILL_AREA ( #8165 ) ; +#58163 = SURFACE_STYLE_USAGE ( .BOTH. , #50989 ) ; +#58164 = VECTOR ( 'NONE', #55575, 1000.000000000000000 ) ; +#58165 = PLANE ( 'NONE', #5259 ) ; +#58166 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64178, 'distance_accuracy_value', 'NONE'); +#58167 = STYLED_ITEM ( 'NONE', ( #189 ), #14155 ) ; +#58168 = EDGE_LOOP ( 'NONE', ( #40276, #33742, #69463, #70757 ) ) ; +#58169 = ORIENTED_EDGE ( 'NONE', *, *, #51391, .T. ) ; +#58170 = VECTOR ( 'NONE', #13442, 1000.000000000000000 ) ; +#58171 = PLANE ( 'NONE', #56790 ) ; +#58172 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58173 = CARTESIAN_POINT ( 'NONE', ( 1.285853239104850054, -1.172828961844079920, 0.8299999999999999600 ) ) ; +#58175 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40218 ), #63036 ) ; +#58174 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58176 = FILL_AREA_STYLE ('',( #98849 ) ) ; +#58177 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58178 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#58179 = LINE ( 'NONE', #90275, #32013 ) ; +#58180 = VERTEX_POINT ( 'NONE', #9686 ) ; +#58181 = PRESENTATION_STYLE_ASSIGNMENT (( #3529 ) ) ; +#58182 = LINE ( 'NONE', #66793, #4800 ) ; +#58183 = LINE ( 'NONE', #59193, #11814 ) ; +#58184 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58185 = SURFACE_STYLE_USAGE ( .BOTH. , #27024 ) ; +#58186 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.299999999999999822, 0.000000000000000000 ) ) ; +#58187 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#58188 = VECTOR ( 'NONE', #68889, 1000.000000000000000 ) ; +#58189 = EDGE_CURVE ( 'NONE', #47921, #27976, #78699, .T. ) ; +#58190 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999990097, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#58191 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58192 = CARTESIAN_POINT ( 'NONE', ( 10.82260475025008795, 8.130910249749913277, 0.8648700000000000276 ) ) ; +#58193 = PRESENTATION_STYLE_ASSIGNMENT (( #27032 ) ) ; +#58194 = SURFACE_STYLE_USAGE ( .BOTH. , #48507 ) ; +#58195 = SURFACE_SIDE_STYLE ('',( #65824 ) ) ; +#58196 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#58197 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53398 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82871, #45036, #36914 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58198 = ORIENTED_EDGE ( 'NONE', *, *, #39478, .T. ) ; +#58199 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58200 = CARTESIAN_POINT ( 'NONE', ( 1.635208922267139986, -0.9074576374047380600, 0.8299999999999999600 ) ) ; +#58201 = EDGE_CURVE ( 'NONE', #56777, #56237, #63425, .T. ) ; +#58202 = ORIENTED_EDGE ( 'NONE', *, *, #99339, .F. ) ; +#58203 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58204 = VECTOR ( 'NONE', #73977, 1000.000000000000000 ) ; +#58205 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#58207 = AXIS2_PLACEMENT_3D ( 'NONE', #81863, #73681, #51721 ) ; +#58206 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58208 = EDGE_CURVE ( 'NONE', #88958, #18897, #44049, .T. ) ; +#58210 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58209 = AXIS2_PLACEMENT_3D ( 'NONE', #51350, #42184, #98217 ) ; +#58211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58212 = STYLED_ITEM ( 'NONE', ( #1940 ), #16768 ) ; +#58213 = ORIENTED_EDGE ( 'NONE', *, *, #20751, .T. ) ; +#58214 = ORIENTED_EDGE ( 'NONE', *, *, #45639, .T. ) ; +#58215 = VECTOR ( 'NONE', #4871, 1000.000000000000000 ) ; +#58216 = SURFACE_STYLE_FILL_AREA ( #41860 ) ; +#58217 = FILL_AREA_STYLE ('',( #27054 ) ) ; +#58218 = LINE ( 'NONE', #34725, #66043 ) ; +#58219 = DIRECTION ( 'NONE', ( -0.7071064476869688420, -0.7071071146859688739, -0.000000000000000000 ) ) ; +#58220 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#58221 = AXIS2_PLACEMENT_3D ( 'NONE', #81157, #32669, #11093 ) ; +#58222 = VECTOR ( 'NONE', #62603, 1000.000000000000000 ) ; +#58223 = EDGE_CURVE ( 'NONE', #61919, #10054, #22173, .T. ) ; +#58224 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58225 = LINE ( 'NONE', #10611, #84414 ) ; +#58226 = FILL_AREA_STYLE ('',( #98901 ) ) ; +#58227 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58229 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56620 ), #98832 ) ; +#58228 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58230 = ORIENTED_EDGE ( 'NONE', *, *, #21825, .T. ) ; +#58231 = EDGE_CURVE ( 'NONE', #30976, #27347, #88387, .T. ) ; +#58232 = VECTOR ( 'NONE', #96689, 1000.000000000000000 ) ; +#58233 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58234 = VERTEX_POINT ( 'NONE', #86880 ) ; +#58235 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90774 ), #9131 ) ; +#58236 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58237 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58238 = FILL_AREA_STYLE_COLOUR ( '', #82288 ) ; +#58239 = VECTOR ( 'NONE', #1611, 1000.000000000000000 ) ; +#58240 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#58241 = EDGE_CURVE ( 'NONE', #22670, #75316, #9183, .T. ) ; +#58242 = CARTESIAN_POINT ( 'NONE', ( -0.3666260071936779941, -1.058874572656040014, 0.8100000000000000533 ) ) ; +#58243 = LINE ( 'NONE', #34743, #36016 ) ; +#58244 = EDGE_CURVE ( 'NONE', #73661, #4405, #16378, .T. ) ; +#58246 = ORIENTED_EDGE ( 'NONE', *, *, #70414, .T. ) ; +#58245 = VERTEX_POINT ( 'NONE', #73069 ) ; +#58247 = DIRECTION ( 'NONE', ( 2.258754526011470139E-17, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58248 = ORIENTED_EDGE ( 'NONE', *, *, #38791, .F. ) ; +#58249 = VECTOR ( 'NONE', #49179, 1000.000000000000000 ) ; +#58250 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58252 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.5000000000000000000, -13.15000000000000036 ) ) ; +#58251 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#58253 = EDGE_LOOP ( 'NONE', ( #30375, #65842, #100728, #52100 ) ) ; +#58254 = ORIENTED_EDGE ( 'NONE', *, *, #13748, .F. ) ; +#58255 = SURFACE_STYLE_FILL_AREA ( #52081 ) ; +#58256 = DIRECTION ( 'NONE', ( 0.7071075504167430026, -0.7071060119555152568, 0.000000000000000000 ) ) ; +#58257 = AXIS2_PLACEMENT_3D ( 'NONE', #70341, #99395, #52538 ) ; +#58259 = LINE ( 'NONE', #11650, #43326 ) ; +#58258 = PRESENTATION_STYLE_ASSIGNMENT (( #17881 ) ) ; +#58260 = VERTEX_POINT ( 'NONE', #34294 ) ; +#58262 = ORIENTED_EDGE ( 'NONE', *, *, #76576, .F. ) ; +#58261 = AXIS2_PLACEMENT_3D ( 'NONE', #10556, #66781, #28494 ) ; +#58263 = SURFACE_STYLE_FILL_AREA ( #43896 ) ; +#58264 = ORIENTED_EDGE ( 'NONE', *, *, #55764, .T. ) ; +#58265 = FILL_AREA_STYLE ('',( #49579 ) ) ; +#58266 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87591 ) ) ; +#58267 = EDGE_CURVE ( 'NONE', #84427, #69329, #48080, .T. ) ; +#58269 = ORIENTED_EDGE ( 'NONE', *, *, #73667, .T. ) ; +#58268 = FILL_AREA_STYLE ('',( #66390 ) ) ; +#58270 = STYLED_ITEM ( 'NONE', ( #2037 ), #84167 ) ; +#58271 = STYLED_ITEM ( 'NONE', ( #32548 ), #90863 ) ; +#58272 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.5000000000000015543, 7.477407789112982559E-79 ) ) ; +#58273 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#58274 = ORIENTED_EDGE ( 'NONE', *, *, #65723, .T. ) ; +#58275 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8648700000000000276 ) ) ; +#58276 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#58277 = ORIENTED_EDGE ( 'NONE', *, *, #8233, .T. ) ; +#58278 = EDGE_CURVE ( 'NONE', #35375, #79695, #26620, .T. ) ; +#58279 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99773 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51393, #35578, #29391 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58280 = ORIENTED_EDGE ( 'NONE', *, *, #48587, .F. ) ; +#58281 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#58282 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#58283 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24010 ) ) ; +#58284 = CARTESIAN_POINT ( 'NONE', ( -1.024943210826370299, -1.268071887441960088, 0.8300000000000000711 ) ) ; +#58285 = EDGE_CURVE ( 'NONE', #28141, #17483, #35802, .T. ) ; +#58286 = SURFACE_STYLE_USAGE ( .BOTH. , #75568 ) ; +#58287 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58288 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95672 ) ) ; +#58289 = CARTESIAN_POINT ( 'NONE', ( 1.585937742812469908, -0.9305358755170231033, 0.8299999999999997380 ) ) ; +#58290 = ORIENTED_EDGE ( 'NONE', *, *, #64671, .F. ) ; +#58291 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58292 = ORIENTED_EDGE ( 'NONE', *, *, #46598, .F. ) ; +#58293 = PRESENTATION_STYLE_ASSIGNMENT (( #27130 ) ) ; +#58294 = FACE_OUTER_BOUND ( 'NONE', #44872, .T. ) ; +#58295 = CARTESIAN_POINT ( 'NONE', ( -0.2295631936502020021, -1.479722134560319979, 0.8299999999999999600 ) ) ; +#58296 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45160 ) ) ; +#58297 = AXIS2_PLACEMENT_3D ( 'NONE', #48149, #79286, #17473 ) ; +#58298 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58299 = LINE ( 'NONE', #20444, #14254 ) ; +#58300 = VECTOR ( 'NONE', #94447, 1000.000000000000000 ) ; +#58302 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#58301 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, -0.7999999999999999334 ) ) ; +#58303 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#58304 = CLOSED_SHELL ( 'NONE', ( #37726, #77765, #5052, #85791, #7946, #18008 ) ) ; +#58305 = PRESENTATION_STYLE_ASSIGNMENT (( #27140 ) ) ; +#58306 = AXIS2_PLACEMENT_3D ( 'NONE', #60550, #70173, #21705 ) ; +#58307 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66811 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51165, #60344, #84293 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58308 = FILL_AREA_STYLE_COLOUR ( '', #5181 ) ; +#58309 = FILL_AREA_STYLE_COLOUR ( '', #3499 ) ; +#58310 = STYLED_ITEM ( 'NONE', ( #38353 ), #5701 ) ; +#58311 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#58312 = EDGE_CURVE ( 'NONE', #80604, #26448, #27633, .T. ) ; +#58313 = EDGE_CURVE ( 'NONE', #84497, #60744, #58784, .T. ) ; +#58314 = ORIENTED_EDGE ( 'NONE', *, *, #76486, .T. ) ; +#58317 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58316 = FILL_AREA_STYLE_COLOUR ( '', #87632 ) ; +#58315 = SURFACE_STYLE_USAGE ( .BOTH. , #67421 ) ; +#58318 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58319 = ORIENTED_EDGE ( 'NONE', *, *, #84028, .T. ) ; +#58320 = FILL_AREA_STYLE ('',( #81293 ) ) ; +#58321 = FILL_AREA_STYLE ('',( #81785 ) ) ; +#58322 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#58323 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58324 = EDGE_CURVE ( 'NONE', #48043, #93815, #75698, .T. ) ; +#58325 = LINE ( 'NONE', #56811, #60087 ) ; +#58326 = LINE ( 'NONE', #19481, #59697 ) ; +#58327 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58328 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58329 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.157142857142859915, 0.8299999999999999600 ) ) ; +#58330 = PLANE ( 'NONE', #79629 ) ; +#58331 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45204 ), #46823 ) ; +#58332 = ORIENTED_EDGE ( 'NONE', *, *, #13652, .F. ) ; +#58333 = FACE_OUTER_BOUND ( 'NONE', #76383, .T. ) ; +#58334 = ORIENTED_EDGE ( 'NONE', *, *, #41528, .F. ) ; +#58335 = FACE_OUTER_BOUND ( 'NONE', #74020, .T. ) ; +#58336 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10336, 'distance_accuracy_value', 'NONE'); +#58337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81028, 'distance_accuracy_value', 'NONE'); +#58338 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#58339 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#58340 = SURFACE_STYLE_FILL_AREA ( #58847 ) ; +#58341 = SURFACE_STYLE_USAGE ( .BOTH. , #50667 ) ; +#58342 = STYLED_ITEM ( 'NONE', ( #47873 ), #84432 ) ; +#58343 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58344 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8100000000000001643 ) ) ; +#58345 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#58346 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#58347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#58348 = CARTESIAN_POINT ( 'NONE', ( 9.231614500500175069, 3.725634500500175417, 0.8991599999999999593 ) ) ; +#58349 = LINE ( 'NONE', #73631, #57586 ) ; +#58350 = ORIENTED_EDGE ( 'NONE', *, *, #23440, .T. ) ; +#58352 = LINE ( 'NONE', #80297, #58084 ) ; +#58351 = STYLED_ITEM ( 'NONE', ( #97180 ), #55165 ) ; +#58353 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333329751, 1.899999999999999911, 0.000000000000000000 ) ) ; +#58354 = VERTEX_POINT ( 'NONE', #51622 ) ; +#58355 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#58356 = ORIENTED_EDGE ( 'NONE', *, *, #17682, .F. ) ; +#58357 = FILL_AREA_STYLE ('',( #27698 ) ) ; +#58358 = SURFACE_STYLE_USAGE ( .BOTH. , #80310 ) ; +#58359 = LINE ( 'NONE', #13795, #94756 ) ; +#58361 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000001332, -0.1400000000000000411 ) ) ; +#58360 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58362 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58363 = EDGE_CURVE ( 'NONE', #74561, #93750, #89388, .T. ) ; +#58364 = ORIENTED_EDGE ( 'NONE', *, *, #85977, .T. ) ; +#58365 = VECTOR ( 'NONE', #90045, 1000.000000000000000 ) ; +#58366 = ORIENTED_EDGE ( 'NONE', *, *, #77444, .F. ) ; +#58367 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86073 ), #53442 ) ; +#58368 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#58369 = CIRCLE ( 'NONE', #40415, 0.009999999999999998473 ) ; +#58370 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58371 = CLOSED_SHELL ( 'NONE', ( #9511, #26947, #11495, #68685, #22683, #96326 ) ) ; +#58372 = ORIENTED_EDGE ( 'NONE', *, *, #67483, .T. ) ; +#58373 = ORIENTED_EDGE ( 'NONE', *, *, #55929, .F. ) ; +#58374 = STYLED_ITEM ( 'NONE', ( #11446 ), #100806 ) ; +#58375 = LINE ( 'NONE', #75651, #59649 ) ; +#58376 = CARTESIAN_POINT ( 'NONE', ( 0.3027121684171390492, -0.9750598911029030313, 0.8100000000000000533 ) ) ; +#58378 = ORIENTED_EDGE ( 'NONE', *, *, #28855, .T. ) ; +#58377 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93020 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86889, #96021, #63915 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58380 = ORIENTED_EDGE ( 'NONE', *, *, #89534, .T. ) ; +#58379 = ORIENTED_EDGE ( 'NONE', *, *, #84458, .T. ) ; +#58381 = ORIENTED_EDGE ( 'NONE', *, *, #34097, .T. ) ; +#58382 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34340 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26988, #18782, #48960 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58383 = EDGE_CURVE ( 'NONE', #29579, #50950, #43920, .T. ) ; +#58384 = ORIENTED_EDGE ( 'NONE', *, *, #42945, .F. ) ; +#58386 = VERTEX_POINT ( 'NONE', #4122 ) ; +#58385 = VECTOR ( 'NONE', #74499, 1000.000000000000000 ) ; +#58387 = SURFACE_STYLE_USAGE ( .BOTH. , #97119 ) ; +#58388 = PLANE ( 'NONE', #92215 ) ; +#58389 = FILL_AREA_STYLE_COLOUR ( '', #80736 ) ; +#58390 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#58391 = ORIENTED_EDGE ( 'NONE', *, *, #26368, .F. ) ; +#58392 = LINE ( 'NONE', #81858, #48897 ) ; +#58393 = SURFACE_STYLE_USAGE ( .BOTH. , #34894 ) ; +#58394 = VERTEX_POINT ( 'NONE', #82247 ) ; +#58395 = EDGE_CURVE ( 'NONE', #93216, #19918, #81758, .T. ) ; +#58396 = FILL_AREA_STYLE ('',( #19031 ) ) ; +#58397 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000005773, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#58398 = FILL_AREA_STYLE_COLOUR ( '', #12104 ) ; +#58399 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#58400 = AXIS2_PLACEMENT_3D ( 'NONE', #31190, #32207, #68949 ) ; +#58401 = STYLED_ITEM ( 'NONE', ( #22090 ), #74492 ) ; +#58402 = CARTESIAN_POINT ( 'NONE', ( -1.313603896932107107, 0.7099999999999999645, 1.079289321881345298 ) ) ; +#58403 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#58404 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#58406 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58405 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.583333333333333481, 0.000000000000000000 ) ) ; +#58407 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46892 ), #64852 ) ; +#58408 = FILL_AREA_STYLE ('',( #49733 ) ) ; +#58409 = LINE ( 'NONE', #73690, #86426 ) ; +#58410 = VERTEX_POINT ( 'NONE', #19441 ) ; +#58411 = EDGE_CURVE ( 'NONE', #62639, #1354, #74583, .T. ) ; +#58412 = PRESENTATION_STYLE_ASSIGNMENT (( #36404 ) ) ; +#58413 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58414 = AXIS2_PLACEMENT_3D ( 'NONE', #66441, #89425, #35835 ) ; +#58415 = SURFACE_STYLE_USAGE ( .BOTH. , #5704 ) ; +#58416 = EDGE_CURVE ( 'NONE', #42518, #40675, #5087, .T. ) ; +#58418 = PLANE ( 'NONE', #32770 ) ; +#58417 = FILL_AREA_STYLE_COLOUR ( '', #73931 ) ; +#58419 = LINE ( 'NONE', #33401, #37194 ) ; +#58420 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#58421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92588 ), #79606 ) ; +#58422 = FILL_AREA_STYLE ('',( #66038 ) ) ; +#58423 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#58424 = VECTOR ( 'NONE', #68522, 1000.000000000000000 ) ; +#58425 = CARTESIAN_POINT ( 'NONE', ( 1.098582290651209936, -0.9005718509792439708, 0.8299999999999999600 ) ) ; +#58426 = ORIENTED_EDGE ( 'NONE', *, *, #64044, .F. ) ; +#58427 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58428 = EDGE_CURVE ( 'NONE', #21902, #66285, #94770, .T. ) ; +#58429 = ADVANCED_FACE ( 'NONE', ( #66407 ), #36288, .T. ) ; +#58430 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58431 = VECTOR ( 'NONE', #69627, 1000.000000000000000 ) ; +#58432 = ORIENTED_EDGE ( 'NONE', *, *, #20270, .F. ) ; +#58433 = CARTESIAN_POINT ( 'NONE', ( -0.9467570119888509828, -1.236164603532529993, 0.8300000000000002931 ) ) ; +#58434 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58435 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90970 ) ) ; +#58437 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58436 = PRESENTATION_STYLE_ASSIGNMENT (( #81892 ) ) ; +#58438 = CARTESIAN_POINT ( 'NONE', ( 1.583412716359319905, -1.066507643917919967, 0.8299999999999999600 ) ) ; +#58439 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#58440 = EDGE_CURVE ( 'NONE', #68999, #39862, #91391, .T. ) ; +#58442 = EDGE_CURVE ( 'NONE', #50949, #5408, #15765, .T. ) ; +#58441 = SURFACE_SIDE_STYLE ('',( #43065 ) ) ; +#58443 = STYLED_ITEM ( 'NONE', ( #88694 ), #23348 ) ; +#58444 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.266666666666667052, 0.000000000000000000 ) ) ; +#58445 = CLOSED_SHELL ( 'NONE', ( #69529, #10363, #1801, #41019, #72986, #16588 ) ) ; +#58446 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#58447 = ORIENTED_EDGE ( 'NONE', *, *, #42842, .T. ) ; +#58448 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58449 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58450 = CARTESIAN_POINT ( 'NONE', ( 0.9820030608313390363, -1.052663393014950044, 0.8299999999999994049 ) ) ; +#58451 = EDGE_CURVE ( 'NONE', #97238, #7382, #8037, .T. ) ; +#58452 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#58453 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#58454 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#58455 = SURFACE_STYLE_FILL_AREA ( #76221 ) ; +#58456 = EDGE_CURVE ( 'NONE', #16, #61742, #61783, .T. ) ; +#58457 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37935, 'distance_accuracy_value', 'NONE'); +#58458 = STYLED_ITEM ( 'NONE', ( #53742 ), #14972 ) ; +#58459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58460 = PRESENTATION_STYLE_ASSIGNMENT (( #20090 ) ) ; +#58461 = VECTOR ( 'NONE', #333, 1000.000000000000000 ) ; +#58462 = FILL_AREA_STYLE ('',( #5239 ) ) ; +#58463 = ORIENTED_EDGE ( 'NONE', *, *, #44614, .F. ) ; +#58464 = EDGE_LOOP ( 'NONE', ( #6904, #41029, #96361, #33807, #48543, #99064, #78326, #77659 ) ) ; +#58465 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#58466 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63249, 'distance_accuracy_value', 'NONE'); +#58467 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66185, 'distance_accuracy_value', 'NONE'); +#58468 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#58469 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58470 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999833, -0.02000000000000000042, 0.1500000000000000222 ) ) ; +#58471 = SURFACE_STYLE_FILL_AREA ( #74249 ) ; +#58472 = FILL_AREA_STYLE_COLOUR ( '', #6326 ) ; +#58473 = SURFACE_SIDE_STYLE ('',( #66092 ) ) ; +#58474 = LINE ( 'NONE', #88071, #74532 ) ; +#58475 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#58476 = FILL_AREA_STYLE_COLOUR ( '', #31371 ) ; +#58478 = ORIENTED_EDGE ( 'NONE', *, *, #73110, .F. ) ; +#58477 = VECTOR ( 'NONE', #97620, 1000.000000000000000 ) ; +#58479 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58480 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87996, 'distance_accuracy_value', 'NONE'); +#58481 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #24720, .NOT_KNOWN. ) ; +#58482 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58483 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91008 ) ) ; +#58484 = EDGE_LOOP ( 'NONE', ( #69474, #52923, #15619, #73797 ) ) ; +#58485 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8648700000000000276 ) ) ; +#58486 = SURFACE_STYLE_USAGE ( .BOTH. , #52792 ) ; +#58487 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58488 = CARTESIAN_POINT ( 'NONE', ( -1.191485992818250184, -1.440849955440170138, 0.8100000000000000533 ) ) ; +#58489 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 9.651189000000000462, 0.8648700000000000276 ) ) ; +#58490 = EDGE_CURVE ( 'NONE', #54228, #58891, #96288, .T. ) ; +#58491 = VERTEX_POINT ( 'NONE', #84726 ) ; +#58492 = FILL_AREA_STYLE ('',( #66108 ) ) ; +#58493 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97172, 'distance_accuracy_value', 'NONE'); +#58494 = AXIS2_PLACEMENT_3D ( 'NONE', #56337, #48141, #70599 ) ; +#58495 = FILL_AREA_STYLE ('',( #10886 ) ) ; +#58496 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58497 = ADVANCED_FACE ( 'NONE', ( #69896 ), #68393, .F. ) ; +#58498 = SURFACE_SIDE_STYLE ('',( #43121 ) ) ; +#58499 = CIRCLE ( 'NONE', #20911, 0.1099999999999998479 ) ; +#58500 = EDGE_LOOP ( 'NONE', ( #7751, #33763, #73009, #2458 ) ) ; +#58501 = LINE ( 'NONE', #89597, #20378 ) ; +#58502 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58503 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58504 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97560 ) ) ; +#58505 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01499999999999999944, 0.1400000000000000133 ) ) ; +#58506 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58507 = ORIENTED_EDGE ( 'NONE', *, *, #66232, .F. ) ; +#58508 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#58509 = VECTOR ( 'NONE', #95803, 1000.000000000000000 ) ; +#58510 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90162, #27401, #29400 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58511 = ORIENTED_EDGE ( 'NONE', *, *, #4118, .T. ) ; +#58513 = VERTEX_POINT ( 'NONE', #56653 ) ; +#58512 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#58514 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25912 ), #71521 ) ; +#58515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58516 = PRESENTATION_STYLE_ASSIGNMENT (( #89115 ) ) ; +#58517 = LINE ( 'NONE', #43626, #19364 ) ; +#58518 = CARTESIAN_POINT ( 'NONE', ( 4.673285226230620488E-18, 0.2499999999999999445, -1.387778780781450606E-17 ) ) ; +#58519 = EDGE_LOOP ( 'NONE', ( #26449, #74055, #12719, #65308 ) ) ; +#58520 = ADVANCED_FACE ( 'NONE', ( #462 ), #87759, .T. ) ; +#58521 = FILL_AREA_STYLE_COLOUR ( '', #877 ) ; +#58522 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#58523 = SURFACE_STYLE_FILL_AREA ( #11918 ) ; +#58524 = ORIENTED_EDGE ( 'NONE', *, *, #27994, .F. ) ; +#58525 = ORIENTED_EDGE ( 'NONE', *, *, #76456, .F. ) ; +#58526 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#58528 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58527 = FACE_OUTER_BOUND ( 'NONE', #74453, .T. ) ; +#58529 = VECTOR ( 'NONE', #59036, 1000.000000000000000 ) ; +#58530 = LINE ( 'NONE', #43643, #19576 ) ; +#58531 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58532 = ORIENTED_EDGE ( 'NONE', *, *, #69646, .F. ) ; +#58533 = FILL_AREA_STYLE ('',( #27354 ) ) ; +#58534 = EDGE_LOOP ( 'NONE', ( #27174, #44234, #73989, #76944 ) ) ; +#58535 = SURFACE_SIDE_STYLE ('',( #20679 ) ) ; +#58536 = FILL_AREA_STYLE_COLOUR ( '', #64147 ) ; +#58537 = ORIENTED_EDGE ( 'NONE', *, *, #25013, .F. ) ; +#58538 = SURFACE_SIDE_STYLE ('',( #28844 ) ) ; +#58539 = EDGE_CURVE ( 'NONE', #42796, #86388, #985, .T. ) ; +#58541 = PLANE ( 'NONE', #92983 ) ; +#58540 = PLANE ( 'NONE', #37917 ) ; +#58542 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#58543 = CARTESIAN_POINT ( 'NONE', ( -0.8193368432721279682, 0.5992714337669160507, 0.8100000000000000533 ) ) ; +#58544 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58545 = FACE_OUTER_BOUND ( 'NONE', #12186, .T. ) ; +#58546 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58547 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 9.368346999999999980, 0.8648700000000000276 ) ) ; +#58548 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58549 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#58550 = ORIENTED_EDGE ( 'NONE', *, *, #21468, .T. ) ; +#58551 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58554 = FILL_AREA_STYLE_COLOUR ( '', #52522 ) ; +#58553 = LINE ( 'NONE', #28375, #81663 ) ; +#58552 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58555 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58556 = VECTOR ( 'NONE', #18890, 1000.000000000000000 ) ; +#58557 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58558 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80062 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69049, #14419, #46602 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58559 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58560 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #2463, #87722, #49428, #17746 ), + ( #12037, #42278, #3957, #81093 ), + ( #26459, #48935, #27460, #73424 ), + ( #88721, #4450, #58126, #2967 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#58562 = ORIENTED_EDGE ( 'NONE', *, *, #53315, .T. ) ; +#58561 = VECTOR ( 'NONE', #71251, 1000.000000000000000 ) ; +#58563 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58564 = VECTOR ( 'NONE', #93304, 1000.000000000000000 ) ; +#58565 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58566 = PRESENTATION_STYLE_ASSIGNMENT (( #27388 ) ) ; +#58567 = FILL_AREA_STYLE ('',( #96291 ) ) ; +#58568 = SURFACE_SIDE_STYLE ('',( #66186 ) ) ; +#58569 = STYLED_ITEM ( 'NONE', ( #4011 ), #80194 ) ; +#58570 = LINE ( 'NONE', #65179, #80675 ) ; +#58571 = SURFACE_STYLE_FILL_AREA ( #4880 ) ; +#58572 = EDGE_CURVE ( 'NONE', #97203, #89230, #70933, .T. ) ; +#58573 = VECTOR ( 'NONE', #46268, 999.9999999999998863 ) ; +#58574 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58575 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58577 = STYLED_ITEM ( 'NONE', ( #72866 ), #24948 ) ; +#58576 = SURFACE_SIDE_STYLE ('',( #51398 ) ) ; +#58578 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#58579 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58580 = SURFACE_STYLE_USAGE ( .BOTH. , #72341 ) ; +#58581 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1481 ) ) ; +#58582 = CARTESIAN_POINT ( 'NONE', ( 1.773496746821729975, -1.132325613921520091, 0.8299999999999997380 ) ) ; +#58583 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1350000000000000089 ) ) ; +#58584 = SURFACE_STYLE_FILL_AREA ( #34587 ) ; +#58585 = VECTOR ( 'NONE', #97978, 1000.000000000000000 ) ; +#58586 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58587 = VERTEX_POINT ( 'NONE', #32135 ) ; +#58588 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32788, 'distance_accuracy_value', 'NONE'); +#58589 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58590 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73840, 'distance_accuracy_value', 'NONE'); +#58591 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000011470, 0.7499999999859485733, 0.6999285677838846809 ) ) ; +#58592 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100822 ), #63464 ) ; +#58593 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58594 = EDGE_CURVE ( 'NONE', #28255, #59760, #25498, .T. ) ; +#58595 = ORIENTED_EDGE ( 'NONE', *, *, #72438, .T. ) ; +#58596 = SURFACE_SIDE_STYLE ('',( #41744 ) ) ; +#58597 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58598 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14662, 'distance_accuracy_value', 'NONE'); +#58599 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50870, 'distance_accuracy_value', 'NONE'); +#58600 = LINE ( 'NONE', #89701, #9852 ) ; +#58601 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #93053, #30598 ) ; +#58602 = EDGE_CURVE ( 'NONE', #47027, #83112, #16258, .T. ) ; +#58603 = PLANE ( 'NONE', #43729 ) ; +#58604 = ORIENTED_EDGE ( 'NONE', *, *, #94691, .F. ) ; +#58605 = ORIENTED_EDGE ( 'NONE', *, *, #67974, .T. ) ; +#58606 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, 0.000000000000000000 ) ) ; +#58607 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100771 ), #7892 ) ; +#58608 = ORIENTED_EDGE ( 'NONE', *, *, #23224, .T. ) ; +#58609 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57002 ), #9581 ) ; +#58611 = SURFACE_STYLE_USAGE ( .BOTH. , #83069 ) ; +#58612 = SURFACE_SIDE_STYLE ('',( #83070 ) ) ; +#58613 = LINE ( 'NONE', #59115, #25539 ) ; +#58614 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 1.100000000000000089 ) ) ; +#58615 = AXIS2_PLACEMENT_3D ( 'NONE', #98758, #51399, #36078 ) ; +#58616 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #27391, #58257 ) ; +#58617 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58618 = FACE_OUTER_BOUND ( 'NONE', #85349, .T. ) ; +#58620 = VERTEX_POINT ( 'NONE', #95383 ) ; +#58619 = ORIENTED_EDGE ( 'NONE', *, *, #36394, .T. ) ; +#58621 = ORIENTED_EDGE ( 'NONE', *, *, #81278, .T. ) ; +#58622 = ORIENTED_EDGE ( 'NONE', *, *, #100633, .T. ) ; +#58623 = AXIS2_PLACEMENT_3D ( 'NONE', #13260, #5638, #99015 ) ; +#58624 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73262 ), #87885 ) ; +#58625 = SURFACE_STYLE_FILL_AREA ( #27458 ) ; +#58626 = FILL_AREA_STYLE ('',( #99306 ) ) ; +#58627 = ORIENTED_EDGE ( 'NONE', *, *, #100444, .F. ) ; +#58628 = AXIS2_PLACEMENT_3D ( 'NONE', #99646, #29800, #53310 ) ; +#58629 = EDGE_CURVE ( 'NONE', #74962, #79295, #17789, .T. ) ; +#58630 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94279 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51445, #20767, #5895 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58631 = PLANE ( 'NONE', #9111 ) ; +#58632 = FILL_AREA_STYLE ('',( #83089 ) ) ; +#58633 = VECTOR ( 'NONE', #16037, 1000.000000000000000 ) ; +#58634 = SURFACE_STYLE_FILL_AREA ( #50473 ) ; +#58635 = ORIENTED_EDGE ( 'NONE', *, *, #77421, .T. ) ; +#58637 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58636 = LINE ( 'NONE', #12045, #37312 ) ; +#58638 = ADVANCED_FACE ( 'NONE', ( #63305 ), #75405, .F. ) ; +#58639 = ORIENTED_EDGE ( 'NONE', *, *, #86243, .F. ) ; +#58640 = ORIENTED_EDGE ( 'NONE', *, *, #91517, .F. ) ; +#58641 = SURFACE_STYLE_FILL_AREA ( #19281 ) ; +#58642 = DIRECTION ( 'NONE', ( 2.168404344971010347E-16, -0.000000000000000000, 1.000000000000000000 ) ) ; +#58643 = VECTOR ( 'NONE', #33061, 1000.000000000000000 ) ; +#58644 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58645 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58646 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#58647 = VERTEX_POINT ( 'NONE', #29929 ) ; +#58648 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #37711, #60704, #28060, #5508 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#58649 = STYLED_ITEM ( 'NONE', ( #66179 ), #42568 ) ; +#58650 = ORIENTED_EDGE ( 'NONE', *, *, #35571, .T. ) ; +#58651 = VERTEX_POINT ( 'NONE', #29450 ) ; +#58652 = AXIS2_PLACEMENT_3D ( 'NONE', #80626, #64774, #70402 ) ; +#58653 = ORIENTED_EDGE ( 'NONE', *, *, #71911, .F. ) ; +#58654 = ORIENTED_EDGE ( 'NONE', *, *, #70378, .F. ) ; +#58655 = EDGE_CURVE ( 'NONE', #77000, #23198, #36630, .T. ) ; +#58657 = LINE ( 'NONE', #43291, #53646 ) ; +#58656 = FILL_AREA_STYLE_COLOUR ( '', #30973 ) ; +#58658 = CYLINDRICAL_SURFACE ( 'NONE', #71042, 0.009999999999999998473 ) ; +#58659 = EDGE_CURVE ( 'NONE', #54259, #41421, #90223, .T. ) ; +#58660 = FILL_AREA_STYLE ('',( #95376 ) ) ; +#58661 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25655 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20454, #68901, #38801 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58662 = ORIENTED_EDGE ( 'NONE', *, *, #39039, .T. ) ; +#58663 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58664 = EDGE_LOOP ( 'NONE', ( #5209, #69505, #95718, #25631 ) ) ; +#58665 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58666 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.9238200612200849760, 0.000000000000000000 ) ) ; +#58667 = VECTOR ( 'NONE', #22899, 1000.000000000000114 ) ; +#58668 = CARTESIAN_POINT ( 'NONE', ( 1.250776364246900085, -1.163804091156239950, 0.8100000000000000533 ) ) ; +#58670 = EDGE_CURVE ( 'NONE', #80338, #41179, #21276, .T. ) ; +#58669 = FILL_AREA_STYLE_COLOUR ( '', #82256 ) ; +#58671 = SURFACE_SIDE_STYLE ('',( #74970 ) ) ; +#58672 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58673 = LINE ( 'NONE', #92140, #37334 ) ; +#58674 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58675 = LINE ( 'NONE', #89777, #89095 ) ; +#58676 = VERTEX_POINT ( 'NONE', #4932 ) ; +#58677 = SURFACE_STYLE_USAGE ( .BOTH. , #4502 ) ; +#58678 = CARTESIAN_POINT ( 'NONE', ( 0.1868680034464730022, -1.007635622941599918, 0.8100000000000010525 ) ) ; +#58679 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #22254, #12506, #37098, #90186 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#58680 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58681 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, 0.09999999999999988065, 0.000000000000000000 ) ) ; +#58682 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77239, #53770, #54811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58683 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.500000000000000000, 8.977651093538432215E-153 ) ) ; +#58684 = PLANE ( 'NONE', #32072 ) ; +#58685 = EDGE_CURVE ( 'NONE', #14189, #87468, #3726, .T. ) ; +#58686 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68390 ) ) ; +#58687 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#58688 = SURFACE_STYLE_FILL_AREA ( #12616 ) ; +#58689 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#58690 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01085786437626909753, 0.2399999999999999911 ) ) ; +#58691 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58692 = STYLED_ITEM ( 'NONE', ( #10152 ), #57362 ) ; +#58693 = STYLED_ITEM ( 'NONE', ( #5757 ), #92033 ) ; +#58694 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#58695 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18853, 'distance_accuracy_value', 'NONE'); +#58696 = STYLED_ITEM ( 'NONE', ( #45181 ), #81322 ) ; +#58697 = ORIENTED_EDGE ( 'NONE', *, *, #23263, .F. ) ; +#58698 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58699 = CARTESIAN_POINT ( 'NONE', ( 1.525294525926170097, -1.013847726018640039, 0.8299999999999999600 ) ) ; +#58700 = ORIENTED_EDGE ( 'NONE', *, *, #22921, .T. ) ; +#58701 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000622, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#58702 = SURFACE_STYLE_FILL_AREA ( #35715 ) ; +#58703 = VECTOR ( 'NONE', #3821, 1000.000000000000000 ) ; +#58704 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#58705 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#58706 = CARTESIAN_POINT ( 'NONE', ( 1.410789937338646993, -1.019697217944821155, 0.8099999999999772937 ) ) ; +#58707 = LINE ( 'NONE', #43344, #64611 ) ; +#58708 = ADVANCED_FACE ( 'NONE', ( #6402 ), #68226, .T. ) ; +#58709 = ORIENTED_EDGE ( 'NONE', *, *, #19836, .T. ) ; +#58710 = ORIENTED_EDGE ( 'NONE', *, *, #17215, .T. ) ; +#58711 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81532 ) ) ; +#58712 = AXIS2_PLACEMENT_3D ( 'NONE', #31106, #46397, #62269 ) ; +#58713 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58714 = STYLED_ITEM ( 'NONE', ( #29385 ), #42631 ) ; +#58715 = FILL_AREA_STYLE ('',( #17847 ) ) ; +#58716 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99804, 'distance_accuracy_value', 'NONE'); +#58717 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58718 = FACE_OUTER_BOUND ( 'NONE', #43894, .T. ) ; +#58719 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57318, 'distance_accuracy_value', 'NONE'); +#58720 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58721 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#58722 = EDGE_CURVE ( 'NONE', #41260, #54871, #28452, .T. ) ; +#58723 = LINE ( 'NONE', #2061, #43585 ) ; +#58724 = SURFACE_SIDE_STYLE ('',( #10105 ) ) ; +#58725 = ORIENTED_EDGE ( 'NONE', *, *, #89689, .F. ) ; +#58726 = AXIS2_PLACEMENT_3D ( 'NONE', #95469, #10127, #89350 ) ; +#58727 = CARTESIAN_POINT ( 'NONE', ( 9.076051124874956244, 8.958224875125043951, 0.8648700000000000276 ) ) ; +#58728 = ORIENTED_EDGE ( 'NONE', *, *, #87442, .F. ) ; +#58730 = FILL_AREA_STYLE_COLOUR ( '', #91927 ) ; +#58729 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58731 = SURFACE_STYLE_USAGE ( .BOTH. , #66360 ) ; +#58732 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58733 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58734 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19556 ), #97844 ) ; +#58735 = CARTESIAN_POINT ( 'NONE', ( 0.4645119866146579790, 0.3274465759269650222, 0.8299999999999999600 ) ) ; +#58736 = LINE ( 'NONE', #19386, #20182 ) ; +#58737 = CARTESIAN_POINT ( 'NONE', ( -0.4878449414651300775, -0.9061750041553330304, 0.8299999999999999600 ) ) ; +#58738 = CARTESIAN_POINT ( 'NONE', ( -1.269090901571400032, -0.9900689134305360461, 0.8299999999999999600 ) ) ; +#58740 = ORIENTED_EDGE ( 'NONE', *, *, #83376, .F. ) ; +#58739 = ORIENTED_EDGE ( 'NONE', *, *, #66825, .F. ) ; +#58741 = SURFACE_STYLE_FILL_AREA ( #88343 ) ; +#58742 = ORIENTED_EDGE ( 'NONE', *, *, #59429, .F. ) ; +#58743 = LINE ( 'NONE', #68357, #8079 ) ; +#58744 = VERTEX_POINT ( 'NONE', #21780 ) ; +#58745 = ORIENTED_EDGE ( 'NONE', *, *, #33261, .T. ) ; +#58746 = PLANE ( 'NONE', #40113 ) ; +#58747 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#58748 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58749 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 3.725635000000000030, 0.8648700000000000276 ) ) ; +#58750 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89693 ) ) ; +#58751 = FILL_AREA_STYLE ('',( #97490 ) ) ; +#58752 = LINE ( 'NONE', #51088, #89928 ) ; +#58753 = VERTEX_POINT ( 'NONE', #52949 ) ; +#58754 = ORIENTED_EDGE ( 'NONE', *, *, #6566, .T. ) ; +#58755 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58756 = EDGE_CURVE ( 'NONE', #35664, #54843, #37628, .T. ) ; +#58757 = EDGE_LOOP ( 'NONE', ( #83552, #91258, #71161, #68093 ) ) ; +#58758 = ADVANCED_FACE ( 'NONE', ( #92217 ), #43751, .T. ) ; +#58759 = FILL_AREA_STYLE_COLOUR ( '', #19917 ) ; +#58760 = STYLED_ITEM ( 'NONE', ( #94742 ), #86185 ) ; +#58761 = AXIS2_PLACEMENT_3D ( 'NONE', #29465, #29943, #76935 ) ; +#58762 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58763 = VECTOR ( 'NONE', #16244, 1000.000000000000114 ) ; +#58764 = ORIENTED_EDGE ( 'NONE', *, *, #73602, .T. ) ; +#58765 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58766 = STYLED_ITEM ( 'NONE', ( #9184 ), #94200 ) ; +#58767 = PLANE ( 'NONE', #58016 ) ; +#58768 = PLANE ( 'NONE', #11333 ) ; +#58769 = VERTEX_POINT ( 'NONE', #30950 ) ; +#58770 = VECTOR ( 'NONE', #74620, 1000.000000000000000 ) ; +#58771 = ORIENTED_EDGE ( 'NONE', *, *, #71406, .T. ) ; +#58772 = EDGE_LOOP ( 'NONE', ( #46020, #91241, #53869, #52687 ) ) ; +#58773 = EDGE_CURVE ( 'NONE', #2974, #24157, #65762, .T. ) ; +#58774 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58775 = STYLED_ITEM ( 'NONE', ( #76523 ), #6761 ) ; +#58776 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 1.149999999999999911, 0.000000000000000000 ) ) ; +#58777 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#58778 = STYLED_ITEM ( 'NONE', ( #91655 ), #65318 ) ; +#58779 = EDGE_CURVE ( 'NONE', #27821, #79030, #16103, .T. ) ; +#58780 = SURFACE_SIDE_STYLE ('',( #6054 ) ) ; +#58781 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58783 = SURFACE_STYLE_USAGE ( .BOTH. , #20434 ) ; +#58782 = PRESENTATION_STYLE_ASSIGNMENT (( #19438 ) ) ; +#58784 = LINE ( 'NONE', #28123, #70295 ) ; +#58785 = AXIS2_PLACEMENT_3D ( 'NONE', #63182, #55525, #23351 ) ; +#58786 = ORIENTED_EDGE ( 'NONE', *, *, #32478, .T. ) ; +#58787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14673 ) ) ; +#58789 = CARTESIAN_POINT ( 'NONE', ( -0.9327878365278901018, -1.419416888468929994, 0.8100000000000000533 ) ) ; +#58790 = ORIENTED_EDGE ( 'NONE', *, *, #31246, .T. ) ; +#58791 = SURFACE_STYLE_USAGE ( .BOTH. , #73578 ) ; +#58792 = PLANE ( 'NONE', #48105 ) ; +#58793 = STYLED_ITEM ( 'NONE', ( #49128 ), #43113 ) ; +#58794 = CARTESIAN_POINT ( 'NONE', ( -0.2991008533676399739, -1.396584910994119966, 0.8100000000000000533 ) ) ; +#58796 = ADVANCED_FACE ( 'NONE', ( #46227 ), #22797, .T. ) ; +#58795 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#58797 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689420, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#58799 = LINE ( 'NONE', #51121, #52446 ) ; +#58798 = CARTESIAN_POINT ( 'NONE', ( 1.429289321881344943, 0.7100000000000000755, -0.9636038969321071290 ) ) ; +#58800 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#58801 = ADVANCED_FACE ( 'NONE', ( #24842 ), #16600, .T. ) ; +#58803 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58802 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6500 ), #47312 ) ; +#58804 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#58805 = AXIS2_PLACEMENT_3D ( 'NONE', #73366, #11978, #83025 ) ; +#58806 = SURFACE_STYLE_FILL_AREA ( #50633 ) ; +#58807 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76682 ) ) ; +#58808 = ORIENTED_EDGE ( 'NONE', *, *, #61324, .T. ) ; +#58809 = ADVANCED_FACE ( 'NONE', ( #10901 ), #1837, .F. ) ; +#58810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58811 = EDGE_CURVE ( 'NONE', #38321, #30183, #96233, .T. ) ; +#58813 = FILL_AREA_STYLE ('',( #96036 ) ) ; +#58812 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58814 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999512, 0.8648700000000000276 ) ) ; +#58816 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3322 ) ) ; +#58815 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58817 = EDGE_CURVE ( 'NONE', #84851, #24082, #57486, .T. ) ; +#58818 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4390, 'distance_accuracy_value', 'NONE'); +#58819 = ORIENTED_EDGE ( 'NONE', *, *, #91119, .T. ) ; +#58820 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58821 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #6598 ) ) ; +#58822 = FILL_AREA_STYLE_COLOUR ( '', #68433 ) ; +#58823 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, 1.449999999999999956, -11.32000000000000028 ) ) ; +#58824 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#58825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58826 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#58827 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50728 ), #32705 ) ; +#58828 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#58829 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76698 ) ) ; +#58830 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58831 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58832 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#58833 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #53390, #39078 ), + ( #70197, #70712 ), + ( #57446, #9363 ), + ( #33450, #31921 ), + ( #64577, #2797 ), + ( #87556, #764 ), + ( #32433, #72232 ), + ( #47742, #48777 ), + ( #63597, #24292 ), + ( #88554, #25301 ), + ( #96195, #78885 ), + ( #79919, #10350 ), + ( #8848, #63084 ), + ( #94679, #47238 ), + ( #55439, #26297 ), + ( #56451, #1277 ), + ( #40090, #40604 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.1152531753007139947, 0.2298694491444699950, 0.2864722980166279909, 0.3435946276136230271, 0.4003635854541520156, 0.4581047010498500160, 0.5163277649124530244, 0.5756887286248180136, 0.6372192592804779565, 0.7009277165726219838, 0.7679686521701940549, 0.8398027673799139947, 0.9173260639101179503, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#58834 = VECTOR ( 'NONE', #55868, 1000.000000000000000 ) ; +#58835 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26236 ), #37664 ) ; +#58836 = CARTESIAN_POINT ( 'NONE', ( 9.125548750249976138, 2.700330249750026113, 0.8648700000000000276 ) ) ; +#58837 = EDGE_CURVE ( 'NONE', #5312, #87098, #18631, .T. ) ; +#58838 = VERTEX_POINT ( 'NONE', #2345 ) ; +#58839 = SURFACE_STYLE_FILL_AREA ( #89437 ) ; +#58840 = ORIENTED_EDGE ( 'NONE', *, *, #9559, .T. ) ; +#58841 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#58842 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51196, 'distance_accuracy_value', 'NONE'); +#58843 = AXIS2_PLACEMENT_3D ( 'NONE', #29947, #60638, #98334 ) ; +#58844 = LINE ( 'NONE', #4657, #46565 ) ; +#58845 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58846 = AXIS2_PLACEMENT_3D ( 'NONE', #11758, #58871, #42511 ) ; +#58847 = FILL_AREA_STYLE ('',( #65442 ) ) ; +#58848 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58849 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#58850 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.266666666666639962, 0.000000000000000000 ) ) ; +#58851 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.149999999999970157, 0.000000000000000000 ) ) ; +#58852 = VECTOR ( 'NONE', #42393, 1000.000000000000000 ) ; +#58853 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#58854 = ORIENTED_EDGE ( 'NONE', *, *, #86778, .F. ) ; +#58855 = ADVANCED_FACE ( 'NONE', ( #49823 ), #58006, .T. ) ; +#58856 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, 0.000000000000000000 ) ) ; +#58857 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58858 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#58859 = ORIENTED_EDGE ( 'NONE', *, *, #47495, .F. ) ; +#58860 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#58861 = AXIS2_PLACEMENT_3D ( 'NONE', #31267, #8208, #85391 ) ; +#58862 = ORIENTED_EDGE ( 'NONE', *, *, #88082, .F. ) ; +#58863 = EDGE_CURVE ( 'NONE', #50319, #85903, #56989, .T. ) ; +#58864 = SURFACE_SIDE_STYLE ('',( #73641 ) ) ; +#58865 = FILL_AREA_STYLE ('',( #18491 ) ) ; +#58866 = SURFACE_STYLE_FILL_AREA ( #74655 ) ; +#58867 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626905764, -0.1400000000000000411 ) ) ; +#58868 = EDGE_CURVE ( 'NONE', #26121, #27723, #35509, .T. ) ; +#58869 = VERTEX_POINT ( 'NONE', #91106 ) ; +#58870 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21272 ) ) ; +#58871 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58872 = ORIENTED_EDGE ( 'NONE', *, *, #100004, .F. ) ; +#58873 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.099999999999980549, 0.000000000000000000 ) ) ; +#58874 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58875 = ORIENTED_EDGE ( 'NONE', *, *, #57671, .T. ) ; +#58876 = ORIENTED_EDGE ( 'NONE', *, *, #34030, .F. ) ; +#58877 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 2.134644999999999904, 0.8648700000000000276 ) ) ; +#58878 = CARTESIAN_POINT ( 'NONE', ( -0.4458598713506949918, -1.104165518103240151, 0.8100000000000000533 ) ) ; +#58879 = FILL_AREA_STYLE_COLOUR ( '', #45348 ) ; +#58880 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58882 = LINE ( 'NONE', #89971, #76124 ) ; +#58881 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#58883 = ORIENTED_EDGE ( 'NONE', *, *, #49080, .T. ) ; +#58885 = ORIENTED_EDGE ( 'NONE', *, *, #63371, .F. ) ; +#58884 = ORIENTED_EDGE ( 'NONE', *, *, #30039, .F. ) ; +#58886 = ORIENTED_EDGE ( 'NONE', *, *, #88377, .F. ) ; +#58888 = EDGE_CURVE ( 'NONE', #98407, #63306, #52329, .T. ) ; +#58887 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58889 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#58890 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58891 = VERTEX_POINT ( 'NONE', #21658 ) ; +#58893 = ORIENTED_EDGE ( 'NONE', *, *, #9038, .T. ) ; +#58892 = FILL_AREA_STYLE ('',( #44499 ) ) ; +#58894 = FILL_AREA_STYLE ('',( #74686 ) ) ; +#58895 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, 0.000000000000000000 ) ) ; +#58896 = PRESENTATION_STYLE_ASSIGNMENT (( #26725 ) ) ; +#58897 = ORIENTED_EDGE ( 'NONE', *, *, #99556, .T. ) ; +#58898 = LINE ( 'NONE', #4226, #12937 ) ; +#58899 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#58900 = SURFACE_STYLE_USAGE ( .BOTH. , #66512 ) ; +#58901 = ORIENTED_EDGE ( 'NONE', *, *, #99442, .T. ) ; +#58902 = EDGE_CURVE ( 'NONE', #61742, #59871, #36010, .T. ) ; +#58903 = CARTESIAN_POINT ( 'NONE', ( 0.4101069733384740124, -1.272991977397700092, 0.8299999999999999600 ) ) ; +#58904 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33077 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42054, #67032, #11810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58905 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68596 ) ) ; +#58906 = CARTESIAN_POINT ( 'NONE', ( 11.23272650050017596, 4.807507500500174835, 0.8991599999999999593 ) ) ; +#58907 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48302 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28486, #42804, #35170 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58908 = SURFACE_STYLE_FILL_AREA ( #27752 ) ; +#58909 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58910 = LINE ( 'NONE', #35910, #99371 ) ; +#58911 = ORIENTED_EDGE ( 'NONE', *, *, #95827, .T. ) ; +#58912 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58913 = VECTOR ( 'NONE', #38676, 1000.000000000000000 ) ; +#58914 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#58915 = CARTESIAN_POINT ( 'NONE', ( 1.432999986405000037, -1.279077976066830047, 0.8300000000000022915 ) ) ; +#58916 = CARTESIAN_POINT ( 'NONE', ( 0.3661974308942260170, -0.9626035508172909871, 0.8100000000000000533 ) ) ; +#58917 = FILL_AREA_STYLE_COLOUR ( '', #95506 ) ; +#58918 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#58919 = VECTOR ( 'NONE', #20147, 1000.000000000000000 ) ; +#58920 = EDGE_CURVE ( 'NONE', #42769, #3356, #51819, .T. ) ; +#58921 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#58922 = AXIS2_PLACEMENT_3D ( 'NONE', #92523, #22612, #53750 ) ; +#58923 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#58924 = ORIENTED_EDGE ( 'NONE', *, *, #29336, .T. ) ; +#58925 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58926 = FILL_AREA_STYLE_COLOUR ( '', #26708 ) ; +#58927 = VERTEX_POINT ( 'NONE', #82954 ) ; +#58928 = ADVANCED_FACE ( 'NONE', ( #29324 ), #82463, .T. ) ; +#58929 = FILL_AREA_STYLE_COLOUR ( '', #58026 ) ; +#58930 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98138 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1120, #63449, #32278 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58931 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58932 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44224 ) ) ; +#58933 = EDGE_CURVE ( 'NONE', #97231, #58260, #54934, .T. ) ; +#58934 = PRESENTATION_STYLE_ASSIGNMENT (( #4752 ) ) ; +#58935 = SURFACE_STYLE_USAGE ( .BOTH. , #41576 ) ; +#58936 = VECTOR ( 'NONE', #51598, 1000.000000000000000 ) ; +#58937 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#58938 = SURFACE_SIDE_STYLE ('',( #67528 ) ) ; +#58939 = CYLINDRICAL_SURFACE ( 'NONE', #82024, 0.04999999999999991257 ) ; +#58940 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8648700000000000276 ) ) ; +#58941 = VERTEX_POINT ( 'NONE', #75784 ) ; +#58942 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58943 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#58944 = PRESENTATION_STYLE_ASSIGNMENT (( #89049 ) ) ; +#58945 = CARTESIAN_POINT ( 'NONE', ( 1.117494933574350036, -0.8946064028769500354, 0.8299999999999994049 ) ) ; +#58946 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#58947 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.8100000000000000533 ) ) ; +#58948 = STYLED_ITEM ( 'NONE', ( #69800 ), #51646 ) ; +#58949 = PRESENTATION_STYLE_ASSIGNMENT (( #20087 ) ) ; +#58950 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#58951 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65566 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96351, #64735, #9530 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#58952 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#58953 = SURFACE_STYLE_FILL_AREA ( #82904 ) ; +#58954 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58955 = PLANE ( 'NONE', #97425 ) ; +#58956 = FILL_AREA_STYLE_COLOUR ( '', #1476 ) ; +#58957 = ORIENTED_EDGE ( 'NONE', *, *, #19569, .F. ) ; +#58958 = FILL_AREA_STYLE ('',( #60455 ) ) ; +#58959 = ORIENTED_EDGE ( 'NONE', *, *, #21134, .T. ) ; +#58960 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#58961 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#58962 = FILL_AREA_STYLE ('',( #34961 ) ) ; +#58963 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8648700000000000276 ) ) ; +#58964 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#58965 = CARTESIAN_POINT ( 'NONE', ( -1.370978437951752005, -1.404803802054160222, 0.8099999999996898570 ) ) ; +#58966 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58967 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#58968 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#58969 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000000934, 0.8991599999999999593 ) ) ; +#58970 = ORIENTED_EDGE ( 'NONE', *, *, #82360, .F. ) ; +#58971 = EDGE_CURVE ( 'NONE', #10128, #30660, #36999, .T. ) ; +#58972 = SURFACE_STYLE_FILL_AREA ( #97205 ) ; +#58973 = FILL_AREA_STYLE ('',( #59480 ) ) ; +#58974 = DIRECTION ( 'NONE', ( 1.224646799147352961E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58975 = STYLED_ITEM ( 'NONE', ( #33279 ), #18368 ) ; +#58976 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47475 ), #85003 ) ; +#58977 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#58978 = EDGE_LOOP ( 'NONE', ( #96728, #433, #69320, #43885, #54485, #14786 ) ) ; +#58979 = EDGE_CURVE ( 'NONE', #40128, #27738, #91598, .T. ) ; +#58980 = FILL_AREA_STYLE ('',( #34982 ) ) ; +#58981 = AXIS2_PLACEMENT_3D ( 'NONE', #10416, #9929, #55517 ) ; +#58982 = CARTESIAN_POINT ( 'NONE', ( 1.289608948985750070, -1.506193478032149979, 0.8299999999999994049 ) ) ; +#58983 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#58984 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#58985 = DIRECTION ( 'NONE', ( -0.7071067811865435759, 0.7071067811865514585, 0.000000000000000000 ) ) ; +#58986 = EDGE_CURVE ( 'NONE', #20296, #81075, #59009, .T. ) ; +#58987 = ORIENTED_EDGE ( 'NONE', *, *, #92010, .T. ) ; +#58988 = PRESENTATION_STYLE_ASSIGNMENT (( #42629 ) ) ; +#58989 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89912 ), #10010 ) ; +#58990 = EDGE_CURVE ( 'NONE', #37113, #14861, #23271, .T. ) ; +#58991 = CYLINDRICAL_SURFACE ( 'NONE', #38862, 0.6999999999999999556 ) ; +#58992 = EDGE_LOOP ( 'NONE', ( #21689, #10963, #20365, #32646 ) ) ; +#58993 = SURFACE_STYLE_FILL_AREA ( #97702 ) ; +#58994 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#58995 = FACE_OUTER_BOUND ( 'NONE', #100269, .T. ) ; +#58997 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91521 ) ) ; +#58996 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, 0.000000000000000000 ) ) ; +#58998 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34502 ) ) ; +#58999 = SURFACE_SIDE_STYLE ('',( #4332 ) ) ; +#59000 = EDGE_LOOP ( 'NONE', ( #98396, #2464, #58277, #1753 ) ) ; +#59001 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#59002 = EDGE_CURVE ( 'NONE', #96354, #1836, #83948, .T. ) ; +#59003 = EDGE_CURVE ( 'NONE', #43745, #9552, #6275, .T. ) ; +#59004 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81797 ) ) ; +#59005 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72026 ), #70382 ) ; +#59006 = EDGE_CURVE ( 'NONE', #28071, #23531, #55362, .T. ) ; +#59007 = ORIENTED_EDGE ( 'NONE', *, *, #12308, .F. ) ; +#59008 = EDGE_CURVE ( 'NONE', #4819, #48677, #683, .T. ) ; +#59010 = ORIENTED_EDGE ( 'NONE', *, *, #5957, .F. ) ; +#59009 = LINE ( 'NONE', #68097, #19948 ) ; +#59011 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43033, 'distance_accuracy_value', 'NONE'); +#59012 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#59014 = CARTESIAN_POINT ( 'NONE', ( -1.337569335501239909, -1.448219210431749948, 0.8299999999999999600 ) ) ; +#59013 = DIRECTION ( 'NONE', ( 0.9388213331153589802, 0.000000000000000000, -0.3444045651374270656 ) ) ; +#59015 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#59016 = SURFACE_STYLE_FILL_AREA ( #97718 ) ; +#59017 = FACE_OUTER_BOUND ( 'NONE', #40402, .T. ) ; +#59018 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.75342000000000020, 0.8648700000000000276 ) ) ; +#59019 = ORIENTED_EDGE ( 'NONE', *, *, #82852, .F. ) ; +#59020 = SURFACE_STYLE_FILL_AREA ( #90104 ) ; +#59021 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59022 = EDGE_CURVE ( 'NONE', #55259, #14770, #100152, .T. ) ; +#59023 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #293 ), #52497 ) ; +#59025 = ORIENTED_EDGE ( 'NONE', *, *, #23960, .T. ) ; +#59027 = SURFACE_SIDE_STYLE ('',( #59538 ) ) ; +#59026 = FILL_AREA_STYLE_COLOUR ( '', #3110 ) ; +#59028 = EDGE_LOOP ( 'NONE', ( #86192, #92974, #56805, #77135 ) ) ; +#59029 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6699 ), #72045 ) ; +#59030 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#59031 = SURFACE_SIDE_STYLE ('',( #21181 ) ) ; +#59032 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3542 ), #68716 ) ; +#59033 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#59034 = VERTEX_POINT ( 'NONE', #54842 ) ; +#59035 = ORIENTED_EDGE ( 'NONE', *, *, #56254, .T. ) ; +#59036 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#59037 = SURFACE_STYLE_FILL_AREA ( #35544 ) ; +#59038 = CARTESIAN_POINT ( 'NONE', ( -1.324712406799700037, -1.164020980542209927, 0.8100000000000000533 ) ) ; +#59039 = PLANE ( 'NONE', #71019 ) ; +#59040 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32915 ) ) ; +#59041 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3555 ) ) ; +#59042 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59043 = PLANE ( 'NONE', #91373 ) ; +#59044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59045 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59046 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60699 ) ) ; +#59048 = AXIS2_PLACEMENT_3D ( 'NONE', #35335, #66437, #20463 ) ; +#59047 = CARTESIAN_POINT ( 'NONE', ( 1.251030810655360037, -0.9616422087329199453, 0.8100000000000000533 ) ) ; +#59049 = ORIENTED_EDGE ( 'NONE', *, *, #21337, .F. ) ; +#59050 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59051 = CARTESIAN_POINT ( 'NONE', ( 1.363488817166419897, -1.341449062141889970, 0.8299999999999994049 ) ) ; +#59052 = EDGE_CURVE ( 'NONE', #14292, #34176, #31831, .T. ) ; +#59055 = FILL_AREA_STYLE ('',( #10954 ) ) ; +#59054 = LINE ( 'NONE', #68150, #13037 ) ; +#59053 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#59056 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17514, 'distance_accuracy_value', 'NONE'); +#59057 = FILL_AREA_STYLE_COLOUR ( '', #58327 ) ; +#59058 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59059 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36223 ), #62311 ) ; +#59060 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8648700000000000276 ) ) ; +#59061 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59062 = EDGE_CURVE ( 'NONE', #79066, #35425, #76784, .T. ) ; +#59063 = SURFACE_STYLE_USAGE ( .BOTH. , #81542 ) ; +#59064 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59065 = ORIENTED_EDGE ( 'NONE', *, *, #66126, .F. ) ; +#59066 = CIRCLE ( 'NONE', #60712, 0.01000000000000002623 ) ; +#59067 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#59068 = FACE_OUTER_BOUND ( 'NONE', #32, .T. ) ; +#59069 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#59070 = LINE ( 'NONE', #45176, #38616 ) ; +#59071 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.000000000000000000 ) ) ; +#59072 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59073 = VECTOR ( 'NONE', #11861, 1000.000000000000000 ) ; +#59074 = LINE ( 'NONE', #90158, #19099 ) ; +#59075 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#59076 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#59077 = EDGE_CURVE ( 'NONE', #68307, #39129, #84445, .T. ) ; +#59078 = SURFACE_STYLE_FILL_AREA ( #83030 ) ; +#59079 = AXIS2_PLACEMENT_3D ( 'NONE', #87483, #3230, #48700 ) ; +#59080 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59081 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59082 = CARTESIAN_POINT ( 'NONE', ( -0.2919245839448350033, -1.051115598670280038, 0.8300000000000009592 ) ) ; +#59083 = PRESENTATION_STYLE_ASSIGNMENT (( #26916 ) ) ; +#59084 = ORIENTED_EDGE ( 'NONE', *, *, #15240, .T. ) ; +#59085 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.449999999999999956, 0.000000000000000000 ) ) ; +#59086 = CYLINDRICAL_SURFACE ( 'NONE', #81959, 0.05000000000000012768 ) ; +#59087 = STYLED_ITEM ( 'NONE', ( #89558 ), #52017 ) ; +#59089 = PRESENTATION_STYLE_ASSIGNMENT (( #60099 ) ) ; +#59088 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.000000000000000000 ) ) ; +#59090 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, -2.710505431213761085E-17, 0.6199999999999999956 ) ) ; +#59091 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77654, #7611, #69978, #9138 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59092 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77869 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11285, #51202, #11776 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59093 = SURFACE_STYLE_USAGE ( .BOTH. , #91683 ) ; +#59094 = FILL_AREA_STYLE ('',( #27421 ) ) ; +#59095 = ORIENTED_EDGE ( 'NONE', *, *, #40728, .T. ) ; +#59096 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#59097 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59098 = ADVANCED_FACE ( 'NONE', ( #15986 ), #47666, .T. ) ; +#59099 = ORIENTED_EDGE ( 'NONE', *, *, #66525, .F. ) ; +#59100 = PLANE ( 'NONE', #13862 ) ; +#59101 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2761799387799140360, -0.02000000000000000042 ) ) ; +#59102 = SURFACE_STYLE_FILL_AREA ( #72011 ) ; +#59103 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59104 = EDGE_CURVE ( 'NONE', #87124, #38846, #8765, .T. ) ; +#59105 = FILL_AREA_STYLE_COLOUR ( '', #69811 ) ; +#59106 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68252, #51482, #83610, #20807 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59107 = ORIENTED_EDGE ( 'NONE', *, *, #91623, .F. ) ; +#59108 = VERTEX_POINT ( 'NONE', #37994 ) ; +#59109 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26434 ) ) ; +#59110 = SURFACE_SIDE_STYLE ('',( #13028 ) ) ; +#59111 = ORIENTED_EDGE ( 'NONE', *, *, #54902, .F. ) ; +#59112 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#59113 = SURFACE_SIDE_STYLE ('',( #97819 ) ) ; +#59114 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#59115 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8648700000000000276 ) ) ; +#59116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11903 ), #16618 ) ; +#59117 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59118 = VECTOR ( 'NONE', #50752, 1000.000000000000000 ) ; +#59119 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51019 ), #70511 ) ; +#59120 = AXIS2_PLACEMENT_3D ( 'NONE', #5257, #66579, #97681 ) ; +#59121 = PLANE ( 'NONE', #73726 ) ; +#59122 = FILL_AREA_STYLE ('',( #42758 ) ) ; +#59124 = ORIENTED_EDGE ( 'NONE', *, *, #14374, .F. ) ; +#59123 = ORIENTED_EDGE ( 'NONE', *, *, #58201, .T. ) ; +#59125 = ORIENTED_EDGE ( 'NONE', *, *, #45005, .F. ) ; +#59126 = EDGE_CURVE ( 'NONE', #80884, #2359, #70119, .T. ) ; +#59127 = AXIS2_PLACEMENT_3D ( 'NONE', #997, #16780, #17807 ) ; +#59128 = VERTEX_POINT ( 'NONE', #46105 ) ; +#59129 = EDGE_CURVE ( 'NONE', #15828, #77784, #77278, .T. ) ; +#59130 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59131 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59132 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31140, 'distance_accuracy_value', 'NONE'); +#59133 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59134 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#59136 = CARTESIAN_POINT ( 'NONE', ( 1.242240128911429986, -0.8869042198941200494, 0.8299999999999999600 ) ) ; +#59135 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59137 = ORIENTED_EDGE ( 'NONE', *, *, #71837, .F. ) ; +#59138 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72850 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16255, #24501, #81633 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59139 = FILL_AREA_STYLE_COLOUR ( '', #61408 ) ; +#59140 = FILL_AREA_STYLE_COLOUR ( '', #56 ) ; +#59141 = STYLED_ITEM ( 'NONE', ( #6484 ), #66456 ) ; +#59142 = ORIENTED_EDGE ( 'NONE', *, *, #37718, .F. ) ; +#59143 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59144 = VERTEX_POINT ( 'NONE', #60988 ) ; +#59145 = ORIENTED_EDGE ( 'NONE', *, *, #37962, .F. ) ; +#59146 = CARTESIAN_POINT ( 'NONE', ( 0.9855976085564051026, -1.097307480365639965, 0.8100000000000000533 ) ) ; +#59147 = EDGE_CURVE ( 'NONE', #15222, #57504, #38495, .T. ) ; +#59148 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19187 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75742, #5253, #22632 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59150 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59149 = SURFACE_STYLE_USAGE ( .BOTH. , #14095 ) ; +#59151 = CARTESIAN_POINT ( 'NONE', ( 1.806468873558769950, -1.190451802854979979, 0.8300000000000004041 ) ) ; +#59152 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #89183, #19206, #11473, #42714 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59153 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2048 ), #11709 ) ; +#59155 = ORIENTED_EDGE ( 'NONE', *, *, #55476, .F. ) ; +#59154 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#59156 = PLANE ( 'NONE', #38486 ) ; +#59157 = VERTEX_POINT ( 'NONE', #94081 ) ; +#59158 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8648700000000000276 ) ) ; +#59159 = PLANE ( 'NONE', #91370 ) ; +#59160 = ORIENTED_EDGE ( 'NONE', *, *, #69872, .T. ) ; +#59161 = FILL_AREA_STYLE_COLOUR ( '', #20459 ) ; +#59162 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000010214, -3.123820061220065281, 0.000000000000000000 ) ) ; +#59164 = EDGE_LOOP ( 'NONE', ( #82138, #12528, #95433, #30906 ) ) ; +#59163 = VECTOR ( 'NONE', #7598, 1000.000000000000000 ) ; +#59165 = ORIENTED_EDGE ( 'NONE', *, *, #66176, .F. ) ; +#59167 = FILL_AREA_STYLE_COLOUR ( '', #69942 ) ; +#59166 = CARTESIAN_POINT ( 'NONE', ( 0.5421186041101929698, -1.033429037169790066, 0.8299999999999992939 ) ) ; +#59168 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#59169 = PLANE ( 'NONE', #79125 ) ; +#59170 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65603 ) ) ; +#59171 = SURFACE_STYLE_FILL_AREA ( #21821 ) ; +#59172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59173 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59174 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59175 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55186, 'distance_accuracy_value', 'NONE'); +#59176 = ORIENTED_EDGE ( 'NONE', *, *, #96890, .F. ) ; +#59177 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59178 = ORIENTED_EDGE ( 'NONE', *, *, #56054, .F. ) ; +#59179 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59180 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 12.10755799999999915, 0.8648700000000000276 ) ) ; +#59181 = CARTESIAN_POINT ( 'NONE', ( -0.09186681814452940520, -0.9637996098261990552, 0.8299999999999999600 ) ) ; +#59182 = CARTESIAN_POINT ( 'NONE', ( 1.381901993660050065, -1.214210613447320064, 0.8100000000000000533 ) ) ; +#59183 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#59184 = VECTOR ( 'NONE', #85892, 1000.000000000000000 ) ; +#59185 = PLANE ( 'NONE', #30449 ) ; +#59186 = FILL_AREA_STYLE_COLOUR ( '', #21069 ) ; +#59187 = ADVANCED_FACE ( 'NONE', ( #93072 ), #92092, .T. ) ; +#59188 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#59189 = ORIENTED_EDGE ( 'NONE', *, *, #83724, .F. ) ; +#59190 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59191 = SURFACE_STYLE_FILL_AREA ( #20841 ) ; +#59192 = VECTOR ( 'NONE', #63245, 1000.000000000000000 ) ; +#59194 = VECTOR ( 'NONE', #30233, 1000.000000000000000 ) ; +#59193 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#59195 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, 0.000000000000000000 ) ) ; +#59196 = PRESENTATION_STYLE_ASSIGNMENT (( #20845 ) ) ; +#59197 = LINE ( 'NONE', #90283, #93557 ) ; +#59198 = CARTESIAN_POINT ( 'NONE', ( 1.797750835596120256, -1.188470249711290228, 0.8100000000000000533 ) ) ; +#59199 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20715, 'distance_accuracy_value', 'NONE'); +#59200 = AXIS2_PLACEMENT_3D ( 'NONE', #25626, #33286, #56280 ) ; +#59201 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#59202 = AXIS2_PLACEMENT_3D ( 'NONE', #4664, #29652, #44954 ) ; +#59203 = FACE_OUTER_BOUND ( 'NONE', #56466, .T. ) ; +#59204 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#59205 = STYLED_ITEM ( 'NONE', ( #71545 ), #59506 ) ; +#59206 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59207 = STYLED_ITEM ( 'NONE', ( #8437 ), #9013 ) ; +#59208 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59209 = AXIS2_PLACEMENT_3D ( 'NONE', #20413, #5562, #29094 ) ; +#59210 = ORIENTED_EDGE ( 'NONE', *, *, #4625, .T. ) ; +#59211 = FILL_AREA_STYLE ('',( #5005 ) ) ; +#59212 = ORIENTED_EDGE ( 'NONE', *, *, #6252, .F. ) ; +#59213 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#59214 = EDGE_CURVE ( 'NONE', #99398, #39930, #87477, .T. ) ; +#59215 = PLANE ( 'NONE', #13774 ) ; +#59216 = FILL_AREA_STYLE ('',( #28048 ) ) ; +#59217 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59218 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, 0.000000000000000000 ) ) ; +#59219 = SURFACE_SIDE_STYLE ('',( #83168 ) ) ; +#59220 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000009909, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#59221 = ORIENTED_EDGE ( 'NONE', *, *, #56070, .T. ) ; +#59222 = ORIENTED_EDGE ( 'NONE', *, *, #97023, .T. ) ; +#59223 = FILL_AREA_STYLE_COLOUR ( '', #60203 ) ; +#59224 = STYLED_ITEM ( 'NONE', ( #37157 ), #70829 ) ; +#59225 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59226 = LINE ( 'NONE', #3565, #10466 ) ; +#59227 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8991599999999999593 ) ) ; +#59228 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#59229 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155850987, 0.8100000000000292522 ) ) ; +#59230 = VECTOR ( 'NONE', #87082, 1000.000000000000000 ) ; +#59231 = EDGE_CURVE ( 'NONE', #87221, #16128, #95603, .T. ) ; +#59232 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59233 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59234 = ORIENTED_EDGE ( 'NONE', *, *, #54612, .F. ) ; +#59235 = ORIENTED_EDGE ( 'NONE', *, *, #10273, .F. ) ; +#59236 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59237 = STYLED_ITEM ( 'NONE', ( #29412 ), #52380 ) ; +#59238 = PRESENTATION_STYLE_ASSIGNMENT (( #28072 ) ) ; +#59239 = ORIENTED_EDGE ( 'NONE', *, *, #18349, .T. ) ; +#59240 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99809 ) ) ; +#59241 = VECTOR ( 'NONE', #15702, 1000.000000000000227 ) ; +#59242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59243 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#59244 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#59245 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8648700000000000276 ) ) ; +#59246 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59247 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#59248 = CARTESIAN_POINT ( 'NONE', ( 0.7761769480519479236, 0.6899999999999999467, 0.1493506493506489285 ) ) ; +#59250 = ORIENTED_EDGE ( 'NONE', *, *, #4631, .T. ) ; +#59249 = ORIENTED_EDGE ( 'NONE', *, *, #37682, .F. ) ; +#59251 = EDGE_LOOP ( 'NONE', ( #52517, #72931, #91281, #66760, #8584, #63276 ) ) ; +#59252 = ADVANCED_FACE ( 'NONE', ( #79833 ), #32354, .F. ) ; +#59253 = CARTESIAN_POINT ( 'NONE', ( 1.585937742812469908, -0.9305358755170229923, 0.8099999999999981659 ) ) ; +#59254 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8592 ), #52725 ) ; +#59255 = AXIS2_PLACEMENT_3D ( 'NONE', #10454, #93891, #24030 ) ; +#59256 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41301, 'distance_accuracy_value', 'NONE'); +#59257 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#59258 = ORIENTED_EDGE ( 'NONE', *, *, #95251, .T. ) ; +#59259 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86913 ), #3745 ) ; +#59260 = ORIENTED_EDGE ( 'NONE', *, *, #84852, .F. ) ; +#59261 = FILL_AREA_STYLE_COLOUR ( '', #80793 ) ; +#59262 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59263 = STYLED_ITEM ( 'NONE', ( #29315 ), #37824 ) ; +#59264 = VECTOR ( 'NONE', #17810, 1000.000000000000000 ) ; +#59265 = LINE ( 'NONE', #89357, #58556 ) ; +#59267 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59266 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1400000000000000133 ) ) ; +#59268 = ORIENTED_EDGE ( 'NONE', *, *, #12078, .T. ) ; +#59269 = VERTEX_POINT ( 'NONE', #87981 ) ; +#59270 = FACE_OUTER_BOUND ( 'NONE', #35104, .T. ) ; +#59271 = ORIENTED_EDGE ( 'NONE', *, *, #16929, .T. ) ; +#59272 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59273 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59274 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59275 = EDGE_CURVE ( 'NONE', #65839, #19143, #34136, .T. ) ; +#59276 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97714 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30552, #15221, #62261 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59278 = ORIENTED_EDGE ( 'NONE', *, *, #92658, .F. ) ; +#59277 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#59279 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73892 ), #25010 ) ; +#59280 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44552 ) ) ; +#59281 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59282 = CARTESIAN_POINT ( 'NONE', ( 1.892524908602200018, -1.389761831846570317, 0.8100000000000006084 ) ) ; +#59283 = VERTEX_POINT ( 'NONE', #96618 ) ; +#59284 = CARTESIAN_POINT ( 'NONE', ( -0.03797038500300969899, -1.235192314287260062, 0.8299999999999999600 ) ) ; +#59285 = LINE ( 'NONE', #90370, #91666 ) ; +#59286 = ORIENTED_EDGE ( 'NONE', *, *, #53097, .T. ) ; +#59287 = ORIENTED_EDGE ( 'NONE', *, *, #24328, .F. ) ; +#59288 = CARTESIAN_POINT ( 'NONE', ( 0.5854301948051939819, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#59289 = SURFACE_SIDE_STYLE ('',( #30083 ) ) ; +#59290 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16706 ) ) ; +#59291 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#59292 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59293 = FILL_AREA_STYLE_COLOUR ( '', #70437 ) ; +#59294 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#59295 = LINE ( 'NONE', #91390, #53103 ) ; +#59296 = ADVANCED_FACE ( 'NONE', ( #80847 ), #26720, .F. ) ; +#59297 = CARTESIAN_POINT ( 'NONE', ( 1.635208922267139986, -0.9074576374047380600, 0.8299999999999997380 ) ) ; +#59298 = ORIENTED_EDGE ( 'NONE', *, *, #66525, .T. ) ; +#59299 = FILL_AREA_STYLE_COLOUR ( '', #47354 ) ; +#59300 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59301 = VERTEX_POINT ( 'NONE', #52216 ) ; +#59302 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78849 ), #3853 ) ; +#59303 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#59304 = CARTESIAN_POINT ( 'NONE', ( -0.2710399284879780324, -1.444662699359970048, 0.8299999999999999600 ) ) ; +#59305 = LINE ( 'NONE', #89396, #44669 ) ; +#59306 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59307 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83752 ), #8645 ) ; +#59308 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#59309 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#59310 = CARTESIAN_POINT ( 'NONE', ( 1.780058980618379971, -1.124571705400470023, 0.8299999999999999600 ) ) ; +#59311 = EDGE_CURVE ( 'NONE', #12872, #27116, #36378, .T. ) ; +#59312 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59313 = LINE ( 'NONE', #90401, #32935 ) ; +#59314 = SURFACE_STYLE_USAGE ( .BOTH. , #35818 ) ; +#59315 = AXIS2_PLACEMENT_3D ( 'NONE', #8977, #24414, #40730 ) ; +#59316 = STYLED_ITEM ( 'NONE', ( #46079 ), #25959 ) ; +#59317 = ORIENTED_EDGE ( 'NONE', *, *, #10564, .F. ) ; +#59319 = DIRECTION ( 'NONE', ( 0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#59318 = STYLED_ITEM ( 'NONE', ( #10175 ), #76363 ) ; +#59320 = FILL_AREA_STYLE ('',( #37805 ) ) ; +#59321 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59322 = VECTOR ( 'NONE', #42110, 1000.000000000000000 ) ; +#59324 = VERTEX_POINT ( 'NONE', #59890 ) ; +#59323 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16823 ) ) ; +#59325 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#59326 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 1.899999999999999911, 0.000000000000000000 ) ) ; +#59328 = STYLED_ITEM ( 'NONE', ( #100203 ), #28876 ) ; +#59327 = STYLED_ITEM ( 'NONE', ( #50702 ), #38019 ) ; +#59329 = FACE_OUTER_BOUND ( 'NONE', #27569, .T. ) ; +#59330 = VECTOR ( 'NONE', #45904, 1000.000000000000114 ) ; +#59331 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67216 ), #23210 ) ; +#59332 = SURFACE_STYLE_FILL_AREA ( #5119 ) ; +#59333 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59334 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59335 = SURFACE_STYLE_USAGE ( .BOTH. , #44931 ) ; +#59337 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59336 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78821 ), #28325 ) ; +#59338 = ADVANCED_FACE ( 'NONE', ( #51207 ), #35891, .T. ) ; +#59339 = EDGE_CURVE ( 'NONE', #16133, #60900, #36876, .T. ) ; +#59340 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66569 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99403, #45830, #77016 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59341 = VECTOR ( 'NONE', #87574, 1000.000000000000000 ) ; +#59342 = SURFACE_SIDE_STYLE ('',( #82293 ) ) ; +#59343 = ORIENTED_EDGE ( 'NONE', *, *, #65112, .F. ) ; +#59344 = FACE_OUTER_BOUND ( 'NONE', #92531, .T. ) ; +#59345 = VERTEX_POINT ( 'NONE', #91492 ) ; +#59346 = FILL_AREA_STYLE_COLOUR ( '', #95922 ) ; +#59347 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34698, 'distance_accuracy_value', 'NONE'); +#59348 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82650, 'distance_accuracy_value', 'NONE'); +#59349 = VECTOR ( 'NONE', #68035, 1000.000000000000000 ) ; +#59350 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#59351 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#59352 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55994, #80471, #87116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59354 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59355 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#59356 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, 0.000000000000000000 ) ) ; +#59357 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59358 = ORIENTED_EDGE ( 'NONE', *, *, #15870, .T. ) ; +#59359 = EDGE_CURVE ( 'NONE', #71728, #4336, #74176, .T. ) ; +#59360 = FACE_OUTER_BOUND ( 'NONE', #58992, .T. ) ; +#59361 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59362 = ADVANCED_FACE ( 'NONE', ( #75662 ), #67977, .F. ) ; +#59363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59364 = EDGE_LOOP ( 'NONE', ( #1071, #28986, #19093, #38504, #41147, #17773, #61946 ) ) ; +#59365 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21767 ) ) ; +#59366 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59367 = VERTEX_POINT ( 'NONE', #22548 ) ; +#59368 = LINE ( 'NONE', #36850, #100528 ) ; +#59369 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59370 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#59371 = SURFACE_SIDE_STYLE ('',( #29188 ) ) ; +#59373 = ORIENTED_EDGE ( 'NONE', *, *, #90038, .F. ) ; +#59372 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10316 ) ) ; +#59374 = FACE_OUTER_BOUND ( 'NONE', #35763, .T. ) ; +#59375 = SURFACE_SIDE_STYLE ('',( #98053 ) ) ; +#59376 = ORIENTED_EDGE ( 'NONE', *, *, #84662, .T. ) ; +#59377 = EDGE_CURVE ( 'NONE', #40392, #39700, #53639, .T. ) ; +#59378 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59379 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56068 ) ) ; +#59380 = VERTEX_POINT ( 'NONE', #22041 ) ; +#59381 = VERTEX_POINT ( 'NONE', #30189 ) ; +#59382 = LINE ( 'NONE', #77031, #9748 ) ; +#59383 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10330 ), #62637 ) ; +#59384 = CARTESIAN_POINT ( 'NONE', ( -0.5298487572449830374, -1.185132602208770036, 0.8100000000000000533 ) ) ; +#59386 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#59385 = SURFACE_SIDE_STYLE ('',( #98062 ) ) ; +#59387 = ORIENTED_EDGE ( 'NONE', *, *, #43964, .T. ) ; +#59388 = VERTEX_POINT ( 'NONE', #84335 ) ; +#59389 = STYLED_ITEM ( 'NONE', ( #17953 ), #47786 ) ; +#59390 = ORIENTED_EDGE ( 'NONE', *, *, #5117, .T. ) ; +#59391 = EDGE_CURVE ( 'NONE', #19759, #100016, #45990, .T. ) ; +#59392 = EDGE_CURVE ( 'NONE', #11284, #61021, #53200, .T. ) ; +#59393 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26789 ), #82250 ) ; +#59395 = VERTEX_POINT ( 'NONE', #55238 ) ; +#59394 = FILL_AREA_STYLE ('',( #29213 ) ) ; +#59396 = CIRCLE ( 'NONE', #78950, 0.009999999999999998473 ) ; +#59397 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#59398 = FILL_AREA_STYLE ('',( #75190 ) ) ; +#59399 = ORIENTED_EDGE ( 'NONE', *, *, #66273, .F. ) ; +#59400 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#59402 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#59401 = AXIS2_PLACEMENT_3D ( 'NONE', #24277, #2295, #40592 ) ; +#59403 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59404 = VERTEX_POINT ( 'NONE', #86344 ) ; +#59405 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59406 = VECTOR ( 'NONE', #44179, 1000.000000000000000 ) ; +#59407 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59408 = CARTESIAN_POINT ( 'NONE', ( 0.4675224071360329914, -1.231957836876500068, 0.8299999999999999600 ) ) ; +#59409 = STYLED_ITEM ( 'NONE', ( #94645 ), #61210 ) ; +#59410 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59411 = VECTOR ( 'NONE', #13270, 1000.000000000000000 ) ; +#59413 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#59412 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#59414 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59415 = ADVANCED_FACE ( 'NONE', ( #85324 ), #70515, .T. ) ; +#59416 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.383333333333320425, 0.000000000000000000 ) ) ; +#59417 = VERTEX_POINT ( 'NONE', #92469 ) ; +#59418 = AXIS2_PLACEMENT_3D ( 'NONE', #59257, #90346, #33739 ) ; +#59419 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59420 = CIRCLE ( 'NONE', #61076, 0.009999999999999998473 ) ; +#59422 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666667052, 2.500000000000000000, 3.495651678170177615E-76 ) ) ; +#59421 = CARTESIAN_POINT ( 'NONE', ( 0.4178376006486049787, -0.9790859034276460093, 0.8100000000000000533 ) ) ; +#59423 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#59424 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 9.092575000000000074, 0.8991599999999999593 ) ) ; +#59425 = EDGE_CURVE ( 'NONE', #60383, #42285, #38388, .T. ) ; +#59426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55302 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67459, #35860, #20506 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59427 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#59429 = EDGE_CURVE ( 'NONE', #96560, #90342, #30687, .T. ) ; +#59428 = CARTESIAN_POINT ( 'NONE', ( 6.367832249750026818, 1.979081249750024307, 0.8648700000000000276 ) ) ; +#59430 = ORIENTED_EDGE ( 'NONE', *, *, #95107, .F. ) ; +#59431 = STYLED_ITEM ( 'NONE', ( #31467 ), #72168 ) ; +#59432 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59433 = FILL_AREA_STYLE_COLOUR ( '', #7053 ) ; +#59434 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -2.356961244533699997E-16 ) ) ; +#59435 = VERTEX_POINT ( 'NONE', #57 ) ; +#59436 = SURFACE_STYLE_USAGE ( .BOTH. , #54647 ) ; +#59437 = LINE ( 'NONE', #29255, #6290 ) ; +#59438 = EDGE_CURVE ( 'NONE', #66888, #10705, #23069, .T. ) ; +#59439 = AXIS2_PLACEMENT_3D ( 'NONE', #27005, #26003, #71951 ) ; +#59441 = FACE_OUTER_BOUND ( 'NONE', #33244, .T. ) ; +#59440 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#59442 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59443 = FILL_AREA_STYLE_COLOUR ( '', #76267 ) ; +#59444 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#59445 = VECTOR ( 'NONE', #14814, 1000.000000000000000 ) ; +#59446 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59447 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59448 = ORIENTED_EDGE ( 'NONE', *, *, #33025, .F. ) ; +#59449 = FILL_AREA_STYLE_COLOUR ( '', #39769 ) ; +#59450 = FACE_OUTER_BOUND ( 'NONE', #20649, .T. ) ; +#59451 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#59452 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2352 ), #56152 ) ; +#59453 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95155 ) ) ; +#59454 = CARTESIAN_POINT ( 'NONE', ( 1.111329997291490068, -1.502675929081449979, 0.8300000000000010703 ) ) ; +#59455 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59456 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59457 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59458 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#59459 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59460 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#59461 = ADVANCED_FACE ( 'NONE', ( #31217 ), #62381, .T. ) ; +#59462 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4162, 'distance_accuracy_value', 'NONE'); +#59463 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.03333333333333168141, 0.000000000000000000 ) ) ; +#59464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18604 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80381, #2271, #78360 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59465 = ORIENTED_EDGE ( 'NONE', *, *, #27404, .F. ) ; +#59466 = FILL_AREA_STYLE ('',( #35470 ) ) ; +#59467 = ORIENTED_EDGE ( 'NONE', *, *, #100244, .F. ) ; +#59468 = LINE ( 'NONE', #90564, #15970 ) ; +#59469 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56767, 'distance_accuracy_value', 'NONE'); +#59470 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69793, 'distance_accuracy_value', 'NONE'); +#59471 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59472 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#59473 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6352, #14025, #28401 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59474 = CARTESIAN_POINT ( 'NONE', ( 1.837535075162280318, -0.9500768360162830106, 0.8100000000000000533 ) ) ; +#59475 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#59476 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#59477 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #216 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30246, #61444, #46044 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59478 = ORIENTED_EDGE ( 'NONE', *, *, #57561, .F. ) ; +#59479 = EDGE_CURVE ( 'NONE', #46875, #2385, #23565, .T. ) ; +#59480 = FILL_AREA_STYLE_COLOUR ( '', #53564 ) ; +#59481 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19163, 'distance_accuracy_value', 'NONE'); +#59482 = EDGE_CURVE ( 'NONE', #35481, #85813, #46054, .T. ) ; +#59485 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21887 ), #52886 ) ; +#59484 = AXIS2_PLACEMENT_3D ( 'NONE', #36514, #83462, #84945 ) ; +#59483 = SURFACE_SIDE_STYLE ('',( #43594 ) ) ; +#59486 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90402 ), #85581 ) ; +#59487 = FILL_AREA_STYLE_COLOUR ( '', #100812 ) ; +#59488 = ORIENTED_EDGE ( 'NONE', *, *, #73195, .F. ) ; +#59489 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33368 ), #47994 ) ; +#59490 = FILL_AREA_STYLE ('',( #98165 ) ) ; +#59491 = CARTESIAN_POINT ( 'NONE', ( 1.268942880527089923, -1.510436674894549913, 0.8299999999999994049 ) ) ; +#59492 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#59493 = CARTESIAN_POINT ( 'NONE', ( -1.302508589717060072, -1.365949044099890264, 0.8299999999999999600 ) ) ; +#59494 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041100000000085, 0.8991599999999999593 ) ) ; +#59495 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#59496 = EDGE_LOOP ( 'NONE', ( #50622, #31099, #834, #75643 ) ) ; +#59497 = PLANE ( 'NONE', #43298 ) ; +#59498 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22979 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25459, #56617, #33617 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59499 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#59500 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42109, 'distance_accuracy_value', 'NONE'); +#59502 = EDGE_CURVE ( 'NONE', #74915, #64246, #85070, .T. ) ; +#59501 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59503 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59504 = CARTESIAN_POINT ( 'NONE', ( 1.581863761282799929, -1.087576819458449862, 0.8099999999999994982 ) ) ; +#59505 = ORIENTED_EDGE ( 'NONE', *, *, #93188, .T. ) ; +#59506 = ADVANCED_FACE ( 'NONE', ( #32238 ), #63887, .T. ) ; +#59507 = FILL_AREA_STYLE ('',( #44604 ) ) ; +#59508 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#59509 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59510 = LINE ( 'NONE', #51811, #21064 ) ; +#59511 = PLANE ( 'NONE', #76052 ) ; +#59512 = VERTEX_POINT ( 'NONE', #1075 ) ; +#59513 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52990 ), #25249 ) ; +#59514 = FILL_AREA_STYLE ('',( #98183 ) ) ; +#59515 = EDGE_CURVE ( 'NONE', #19790, #63866, #16871, .T. ) ; +#59516 = ADVANCED_FACE ( 'NONE', ( #41416 ), #64381, .T. ) ; +#59517 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98445 ), #85546 ) ; +#59518 = VERTEX_POINT ( 'NONE', #88363 ) ; +#59520 = EDGE_LOOP ( 'NONE', ( #38994, #87190, #21794, #1270 ) ) ; +#59519 = SURFACE_SIDE_STYLE ('',( #28815 ) ) ; +#59521 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.7071067811865474617, -0.7071067811865474617 ) ) ; +#59522 = VECTOR ( 'NONE', #58205, 1000.000000000000000 ) ; +#59524 = FILL_AREA_STYLE ('',( #4823 ) ) ; +#59523 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59526 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#59525 = CIRCLE ( 'NONE', #36681, 0.009999999999999998473 ) ; +#59527 = FACE_OUTER_BOUND ( 'NONE', #79676, .T. ) ; +#59528 = PRESENTATION_STYLE_ASSIGNMENT (( #83466 ) ) ; +#59529 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#59530 = ORIENTED_EDGE ( 'NONE', *, *, #25880, .F. ) ; +#59531 = CARTESIAN_POINT ( 'NONE', ( 1.248152242693560066, -1.513291690750319995, 0.8299999999999999600 ) ) ; +#59532 = SURFACE_STYLE_USAGE ( .BOTH. , #60013 ) ; +#59533 = STYLED_ITEM ( 'NONE', ( #90477 ), #82175 ) ; +#59534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80715 ), #15417 ) ; +#59535 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#59536 = ORIENTED_EDGE ( 'NONE', *, *, #56953, .F. ) ; +#59538 = SURFACE_STYLE_FILL_AREA ( #2860 ) ; +#59537 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#59539 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59540 = ORIENTED_EDGE ( 'NONE', *, *, #62078, .T. ) ; +#59541 = FILL_AREA_STYLE ('',( #67133 ) ) ; +#59542 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59543 = ADVANCED_FACE ( 'NONE', ( #18395 ), #41912, .T. ) ; +#59544 = LINE ( 'NONE', #43646, #19656 ) ; +#59545 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41037, #56865, #86979, #16999 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59546 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8991599999999999593 ) ) ; +#59547 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24257 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85117, #61671, #346 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59548 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59549 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22020 ) ) ; +#59550 = ORIENTED_EDGE ( 'NONE', *, *, #97584, .T. ) ; +#59551 = VERTEX_POINT ( 'NONE', #96494 ) ; +#59552 = VECTOR ( 'NONE', #30130, 1000.000000000000000 ) ; +#59554 = FILL_AREA_STYLE_COLOUR ( '', #80019 ) ; +#59553 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59555 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59556 = EDGE_CURVE ( 'NONE', #31700, #38992, #26598, .T. ) ; +#59557 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96942 ) ) ; +#59558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25287 ) ) ; +#59560 = EDGE_CURVE ( 'NONE', #94101, #69571, #16882, .T. ) ; +#59559 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#59561 = PLANE ( 'NONE', #57731 ) ; +#59562 = PRESENTATION_STYLE_ASSIGNMENT (( #5335 ) ) ; +#59563 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59564 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28469 ), #77420 ) ; +#59565 = CARTESIAN_POINT ( 'NONE', ( -0.8073450731391820234, 0.5791240218592531575, 0.8100000000000000533 ) ) ; +#59566 = ORIENTED_EDGE ( 'NONE', *, *, #33865, .F. ) ; +#59567 = SURFACE_STYLE_USAGE ( .BOTH. , #26884 ) ; +#59568 = ADVANCED_FACE ( 'NONE', ( #51609 ), #50595, .F. ) ; +#59569 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#59570 = AXIS2_PLACEMENT_3D ( 'NONE', #49306, #96237, #73303 ) ; +#59571 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59572 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59573 = PRESENTATION_STYLE_ASSIGNMENT (( #35567 ) ) ; +#59574 = SURFACE_SIDE_STYLE ('',( #76325 ) ) ; +#59575 = FACE_OUTER_BOUND ( 'NONE', #16619, .T. ) ; +#59576 = EDGE_LOOP ( 'NONE', ( #20620, #78938, #25359, #26713 ) ) ; +#59577 = SURFACE_STYLE_FILL_AREA ( #74842 ) ; +#59578 = LINE ( 'NONE', #67654, #13523 ) ; +#59579 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#59580 = SURFACE_SIDE_STYLE ('',( #27389 ) ) ; +#59581 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000777, 0.1399999999999999856 ) ) ; +#59582 = AXIS2_PLACEMENT_3D ( 'NONE', #99644, #83448, #75773 ) ; +#59583 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -11.57000000000000028 ) ) ; +#59584 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66102 ), #95349 ) ; +#59585 = FACE_OUTER_BOUND ( 'NONE', #18265, .T. ) ; +#59586 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59587 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, 3.500000000000000444, 0.000000000000000000 ) ) ; +#59588 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59589 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59590 = SURFACE_SIDE_STYLE ('',( #59078 ) ) ; +#59591 = FILL_AREA_STYLE ('',( #61070 ) ) ; +#59592 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.5833333333333333703, 0.000000000000000000 ) ) ; +#59593 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90195, 'distance_accuracy_value', 'NONE'); +#59594 = STYLED_ITEM ( 'NONE', ( #42606 ), #89760 ) ; +#59595 = PLANE ( 'NONE', #82937 ) ; +#59596 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59597 = CARTESIAN_POINT ( 'NONE', ( -0.2218544649797319912, -0.9305358755170231033, 0.8300000000000009592 ) ) ; +#59598 = FACE_OUTER_BOUND ( 'NONE', #83323, .T. ) ; +#59599 = CARTESIAN_POINT ( 'NONE', ( -0.9202467668417529945, -1.279077976066830047, 0.8299999999999999600 ) ) ; +#59600 = EDGE_LOOP ( 'NONE', ( #98219, #82679, #28900, #94959 ) ) ; +#59601 = SURFACE_STYLE_FILL_AREA ( #5383 ) ; +#59602 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65815, 'distance_accuracy_value', 'NONE'); +#59603 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59604 = EDGE_CURVE ( 'NONE', #97123, #42769, #60268, .T. ) ; +#59605 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59606 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28377, 'distance_accuracy_value', 'NONE'); +#59607 = CARTESIAN_POINT ( 'NONE', ( -0.009357855636228630536, -1.039339352017210061, 0.8300000000000002931 ) ) ; +#59608 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59609 = SURFACE_STYLE_FILL_AREA ( #28420 ) ; +#59610 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59611 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#59612 = EDGE_LOOP ( 'NONE', ( #93574, #44955, #95489, #55463 ) ) ; +#59613 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59614 = ORIENTED_EDGE ( 'NONE', *, *, #6148, .F. ) ; +#59615 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000140062184, 0.000000000000000000 ) ) ; +#59616 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60690, 'distance_accuracy_value', 'NONE'); +#59617 = FILL_AREA_STYLE ('',( #97331 ) ) ; +#59618 = AXIS2_PLACEMENT_3D ( 'NONE', #50166, #13247, #81310 ) ; +#59619 = FACE_OUTER_BOUND ( 'NONE', #78676, .T. ) ; +#59620 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48215 ), #40038 ) ; +#59621 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, -3.499999999999969802, 0.1829999999999999960 ) ) ; +#59622 = ORIENTED_EDGE ( 'NONE', *, *, #66145, .F. ) ; +#59623 = VERTEX_POINT ( 'NONE', #59277 ) ; +#59625 = STYLED_ITEM ( 'NONE', ( #52988 ), #27311 ) ; +#59624 = VECTOR ( 'NONE', #27111, 1000.000000000000000 ) ; +#59626 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18830 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7694, #622, #24148 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59627 = SURFACE_SIDE_STYLE ('',( #89216 ) ) ; +#59628 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59629 = VERTEX_POINT ( 'NONE', #50095 ) ; +#59630 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#59631 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#59632 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#59633 = AXIS2_PLACEMENT_3D ( 'NONE', #202, #31856, #85978 ) ; +#59634 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#59635 = STYLED_ITEM ( 'NONE', ( #73223 ), #98086 ) ; +#59636 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #80845, #39310 ) ; +#59637 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59639 = VERTEX_POINT ( 'NONE', #3605 ) ; +#59638 = ORIENTED_EDGE ( 'NONE', *, *, #65598, .T. ) ; +#59640 = EDGE_CURVE ( 'NONE', #97792, #38779, #82714, .T. ) ; +#59641 = EDGE_LOOP ( 'NONE', ( #67158, #91240, #32214, #21975 ) ) ; +#59642 = ORIENTED_EDGE ( 'NONE', *, *, #18662, .T. ) ; +#59643 = FILL_AREA_STYLE_COLOUR ( '', #80223 ) ; +#59644 = VECTOR ( 'NONE', #40249, 1000.000000000000000 ) ; +#59645 = FILL_AREA_STYLE ('',( #98317 ) ) ; +#59646 = FACE_OUTER_BOUND ( 'NONE', #34430, .T. ) ; +#59647 = EDGE_CURVE ( 'NONE', #91883, #19807, #81236, .T. ) ; +#59648 = SURFACE_SIDE_STYLE ('',( #12553 ) ) ; +#59649 = VECTOR ( 'NONE', #4690, 999.9999999999998863 ) ; +#59650 = VERTEX_POINT ( 'NONE', #34774 ) ; +#59651 = STYLED_ITEM ( 'NONE', ( #95888 ), #73143 ) ; +#59653 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59652 = SURFACE_SIDE_STYLE ('',( #96867 ) ) ; +#59654 = VERTEX_POINT ( 'NONE', #90876 ) ; +#59655 = ORIENTED_EDGE ( 'NONE', *, *, #59231, .F. ) ; +#59656 = SURFACE_SIDE_STYLE ('',( #12049 ) ) ; +#59657 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100060, #30206, #53714, #30706, #75686, #98572, #52719, #84356, #60410, #84839, #54225, #61897, #15379, #14357, #46531, #45503, #92970, #59912, #21076, #13315, #5694, #52238, #36894, #68002, #83859, #13840, #45017, #10541, #95891, #73458, #62400, #42314, #41808, #93974, #25999, #15888 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 1, 1, 1, 2, 2, 1, 2, 2, 1, 1, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.06249999999999800160, 0.1249999999999960032, 0.1874999999999940048, 0.2187499999999931999, 0.2499999999999923950, 0.3749999999999884537, 0.4374999999999870659, 0.4687499999999870659, 0.4843749999999873990, 0.4999999999999877875, 0.5624999999999933387, 0.5937499999999955591, 0.6249999999999977796, 0.6875000000000029976, 0.7187500000000054401, 0.7343750000000057732, 0.7500000000000062172, 0.8125000000000042188, 0.8437500000000032196, 0.8750000000000022204, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59659 = FILL_AREA_STYLE_COLOUR ( '', #22185 ) ; +#59658 = PRESENTATION_STYLE_ASSIGNMENT (( #44259 ) ) ; +#59660 = VECTOR ( 'NONE', #27498, 1000.000000000000000 ) ; +#59661 = CARTESIAN_POINT ( 'NONE', ( 1.841098443137489937, -1.205608583660890076, 0.8300000000000004041 ) ) ; +#59662 = EDGE_CURVE ( 'NONE', #31422, #14361, #28104, .T. ) ; +#59664 = ORIENTED_EDGE ( 'NONE', *, *, #57199, .T. ) ; +#59663 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8648700000000000276 ) ) ; +#59665 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.164082792207790096, 0.8100000000000000533 ) ) ; +#59666 = AXIS2_PLACEMENT_3D ( 'NONE', #73446, #3985, #89265 ) ; +#59667 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13849 ) ) ; +#59668 = ORIENTED_EDGE ( 'NONE', *, *, #56925, .T. ) ; +#59669 = ORIENTED_EDGE ( 'NONE', *, *, #32530, .T. ) ; +#59670 = ORIENTED_EDGE ( 'NONE', *, *, #39408, .F. ) ; +#59672 = EDGE_CURVE ( 'NONE', #88828, #92506, #83227, .T. ) ; +#59671 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #866 ) ) ; +#59673 = FACE_OUTER_BOUND ( 'NONE', #14174, .T. ) ; +#59674 = SURFACE_STYLE_USAGE ( .BOTH. , #37656 ) ; +#59675 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36220 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98321, #28461, #36138 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59676 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59677 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18864 ) ) ; +#59678 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#59679 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#59680 = ORIENTED_EDGE ( 'NONE', *, *, #24989, .T. ) ; +#59681 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59682 = VERTEX_POINT ( 'NONE', #20929 ) ; +#59683 = ADVANCED_FACE ( 'NONE', ( #67382 ), #98446, .T. ) ; +#59684 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59685 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#59686 = LINE ( 'NONE', #52000, #69551 ) ; +#59687 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.1499999999999999667, 0.1900000000000000022 ) ) ; +#59688 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59689 = VECTOR ( 'NONE', #49156, 1000.000000000000000 ) ; +#59690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59691 = EDGE_CURVE ( 'NONE', #82555, #62344, #82755, .T. ) ; +#59692 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59693 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59694 = VERTEX_POINT ( 'NONE', #85199 ) ; +#59695 = VECTOR ( 'NONE', #15752, 1000.000000000000000 ) ; +#59696 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59697 = VECTOR ( 'NONE', #64442, 1000.000000000000000 ) ; +#59698 = FILL_AREA_STYLE_COLOUR ( '', #13630 ) ; +#59699 = CARTESIAN_POINT ( 'NONE', ( 0.3170313104546300109, -0.9034630071664919715, 0.8100000000000000533 ) ) ; +#59700 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 11.25335600000000014, 0.8648700000000000276 ) ) ; +#59701 = SURFACE_STYLE_FILL_AREA ( #74485 ) ; +#59702 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59703 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#59704 = CARTESIAN_POINT ( 'NONE', ( 1.886527894060100019, -1.258231835375339891, 0.8100000000000000533 ) ) ; +#59705 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59706 = EDGE_CURVE ( 'NONE', #33894, #48689, #96096, .T. ) ; +#59708 = ADVANCED_FACE ( 'NONE', ( #6537 ), #84710, .T. ) ; +#59707 = FACE_OUTER_BOUND ( 'NONE', #85420, .T. ) ; +#59709 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43400 ), #98776 ) ; +#59710 = SURFACE_SIDE_STYLE ('',( #35700 ) ) ; +#59711 = SURFACE_SIDE_STYLE ('',( #52506 ) ) ; +#59712 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.9000000000000001332, -0.02000000000002513309 ) ) ; +#59713 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.8499999999999999778, 0.000000000000000000 ) ) ; +#59714 = STYLED_ITEM ( 'NONE', ( #51476 ), #3863 ) ; +#59715 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#59716 = ADVANCED_FACE ( 'NONE', ( #54609 ), #7018, .T. ) ; +#59717 = ADVANCED_FACE ( 'NONE', ( #71928 ), #86732, .T. ) ; +#59718 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75384, 'distance_accuracy_value', 'NONE'); +#59719 = VERTEX_POINT ( 'NONE', #86217 ) ; +#59720 = LINE ( 'NONE', #68308, #77870 ) ; +#59721 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#59722 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, 0.6500000000000001332 ) ) ; +#59723 = ORIENTED_EDGE ( 'NONE', *, *, #96627, .T. ) ; +#59724 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#59725 = SURFACE_STYLE_FILL_AREA ( #5498 ) ; +#59726 = EDGE_CURVE ( 'NONE', #41891, #4442, #48954, .T. ) ; +#59727 = FILL_AREA_STYLE ('',( #84157 ) ) ; +#59728 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52219, 'distance_accuracy_value', 'NONE'); +#59729 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.100000000000000311, -0.02000000000000000042 ) ) ; +#59730 = AXIS2_PLACEMENT_3D ( 'NONE', #70793, #40680, #25376 ) ; +#59731 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.383333333333326642, 0.000000000000000000 ) ) ; +#59732 = EDGE_CURVE ( 'NONE', #46887, #53732, #56114, .T. ) ; +#59733 = EDGE_LOOP ( 'NONE', ( #55352, #87373, #43243, #35557 ) ) ; +#59734 = SURFACE_STYLE_USAGE ( .BOTH. , #74518 ) ; +#59735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59736 = FILL_AREA_STYLE ('',( #90315 ) ) ; +#59737 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59738 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15086, 'distance_accuracy_value', 'NONE'); +#59739 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10688 ) ) ; +#59740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65983, 'distance_accuracy_value', 'NONE'); +#59741 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89076 ) ) ; +#59742 = PLANE ( 'NONE', #96726 ) ; +#59743 = AXIS2_PLACEMENT_3D ( 'NONE', #94601, #24719, #72156 ) ; +#59744 = AXIS2_PLACEMENT_3D ( 'NONE', #25146, #50135, #10178 ) ; +#59745 = ORIENTED_EDGE ( 'NONE', *, *, #3850, .T. ) ; +#59747 = EDGE_LOOP ( 'NONE', ( #78563, #69354, #3361, #51072, #15121, #72507 ) ) ; +#59746 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35239 ), #40177 ) ; +#59748 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82736, 'distance_accuracy_value', 'NONE'); +#59749 = EDGE_LOOP ( 'NONE', ( #46410, #32598, #36849, #27680 ) ) ; +#59750 = CARTESIAN_POINT ( 'NONE', ( -0.1344673260136140247, -1.507258815139120189, 0.8299999999999999600 ) ) ; +#59751 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6240 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34026, #63153, #33520 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59752 = LINE ( 'NONE', #53052, #98959 ) ; +#59753 = LINE ( 'NONE', #59243, #90676 ) ; +#59754 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59755 = PLANE ( 'NONE', #31638 ) ; +#59756 = PRESENTATION_STYLE_ASSIGNMENT (( #36731 ) ) ; +#59757 = VECTOR ( 'NONE', #56502, 1000.000000000000000 ) ; +#59758 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#59759 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#59761 = VERTEX_POINT ( 'NONE', #87228 ) ; +#59760 = VERTEX_POINT ( 'NONE', #2480 ) ; +#59763 = EDGE_CURVE ( 'NONE', #25440, #88871, #33639, .T. ) ; +#59762 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67935, #36831, #45943, #99508 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59764 = ORIENTED_EDGE ( 'NONE', *, *, #16292, .F. ) ; +#59765 = CARTESIAN_POINT ( 'NONE', ( 1.601121020982049670, -0.9216047924506349798, 0.8099999999999981659 ) ) ; +#59767 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59766 = LINE ( 'NONE', #83706, #55516 ) ; +#59768 = EDGE_LOOP ( 'NONE', ( #28284, #8136, #30839, #70555 ) ) ; +#59769 = ADVANCED_FACE ( 'NONE', ( #16239 ), #78553, .T. ) ; +#59770 = EDGE_LOOP ( 'NONE', ( #26570, #78307, #77802 ) ) ; +#59771 = VECTOR ( 'NONE', #64290, 999.9999999999998863 ) ; +#59772 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8648700000000000276 ) ) ; +#59773 = STYLED_ITEM ( 'NONE', ( #78889 ), #99710 ) ; +#59774 = LINE ( 'NONE', #83714, #50394 ) ; +#59775 = LINE ( 'NONE', #14203, #77576 ) ; +#59776 = FACE_OUTER_BOUND ( 'NONE', #56334, .T. ) ; +#59777 = ORIENTED_EDGE ( 'NONE', *, *, #88918, .F. ) ; +#59778 = EDGE_LOOP ( 'NONE', ( #19513, #65778, #87863, #75404 ) ) ; +#59779 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#59780 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59781 = VERTEX_POINT ( 'NONE', #55618 ) ; +#59782 = LINE ( 'NONE', #21923, #42806 ) ; +#59783 = PLANE ( 'NONE', #36361 ) ; +#59784 = CIRCLE ( 'NONE', #25503, 0.02999999999999997113 ) ; +#59786 = ORIENTED_EDGE ( 'NONE', *, *, #90545, .F. ) ; +#59785 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#59787 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#59788 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#59789 = FILL_AREA_STYLE ('',( #18908 ) ) ; +#59790 = ORIENTED_EDGE ( 'NONE', *, *, #4146, .F. ) ; +#59791 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59792 = VERTEX_POINT ( 'NONE', #47932 ) ; +#59793 = ORIENTED_EDGE ( 'NONE', *, *, #6456, .T. ) ; +#59794 = EDGE_CURVE ( 'NONE', #22262, #40797, #79083, .T. ) ; +#59795 = LINE ( 'NONE', #34285, #13834 ) ; +#59796 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59797 = VECTOR ( 'NONE', #54231, 1000.000000000000000 ) ; +#59798 = FILL_AREA_STYLE_COLOUR ( '', #39532 ) ; +#59799 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#59800 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27199 ), #22277 ) ; +#59801 = ORIENTED_EDGE ( 'NONE', *, *, #24893, .F. ) ; +#59802 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#59803 = CARTESIAN_POINT ( 'NONE', ( -1.023967505146820001, -1.493640573211080014, 0.8100000000000010525 ) ) ; +#59804 = ORIENTED_EDGE ( 'NONE', *, *, #93069, .T. ) ; +#59805 = PLANE ( 'NONE', #74132 ) ; +#59806 = LINE ( 'NONE', #34799, #46669 ) ; +#59807 = FILL_AREA_STYLE_COLOUR ( '', #12032 ) ; +#59808 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49944 ), #76001 ) ; +#59809 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26920 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80890, #58430, #65525 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59811 = FACE_OUTER_BOUND ( 'NONE', #76043, .T. ) ; +#59810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59812 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.2999999999999999889, -0.02000000000001960279 ) ) ; +#59813 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #40584, #70689, #24265, #742 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59814 = SURFACE_STYLE_USAGE ( .BOTH. , #5592 ) ; +#59815 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59816 = SURFACE_STYLE_USAGE ( .BOTH. , #19057 ) ; +#59817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100448 ), #69578 ) ; +#59818 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59819 = SURFACE_STYLE_USAGE ( .BOTH. , #67419 ) ; +#59821 = LINE ( 'NONE', #98979, #10944 ) ; +#59820 = CARTESIAN_POINT ( 'NONE', ( -0.03225693158157669910, -1.237517385711579099, 0.8099999999998911404 ) ) ; +#59822 = LINE ( 'NONE', #43445, #65220 ) ; +#59823 = VECTOR ( 'NONE', #35686, 1000.000000000000000 ) ; +#59824 = FILL_AREA_STYLE ('',( #52141 ) ) ; +#59825 = EDGE_CURVE ( 'NONE', #100280, #7067, #1479, .T. ) ; +#59826 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92402 ), #42083 ) ; +#59827 = STYLED_ITEM ( 'NONE', ( #48293 ), #15901 ) ; +#59828 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8596, 'distance_accuracy_value', 'NONE'); +#59829 = ORIENTED_EDGE ( 'NONE', *, *, #63141, .F. ) ; +#59830 = CLOSED_SHELL ( 'NONE', ( #89653, #77591, #49090, #9404, #6168, #62566 ) ) ; +#59831 = CARTESIAN_POINT ( 'NONE', ( -1.061635297135890221, -1.433733517242619993, 0.8299999999999999600 ) ) ; +#59832 = FACE_OUTER_BOUND ( 'NONE', #77388, .T. ) ; +#59833 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#59834 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.300000000000000044, -0.02000000000000630093 ) ) ; +#59835 = PRESENTATION_STYLE_ASSIGNMENT (( #60323 ) ) ; +#59836 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660784, -1.070941558441560026, 0.8100000000000001643 ) ) ; +#59837 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#59838 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59839 = CARTESIAN_POINT ( 'NONE', ( 0.2166666666666670071, 3.099999999999980549, 0.000000000000000000 ) ) ; +#59840 = AXIS2_PLACEMENT_3D ( 'NONE', #60102, #51423, #99280 ) ; +#59841 = EDGE_CURVE ( 'NONE', #44826, #24940, #16774, .T. ) ; +#59842 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69532 ) ) ; +#59843 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#59844 = ORIENTED_EDGE ( 'NONE', *, *, #47961, .F. ) ; +#59845 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59846 = VERTEX_POINT ( 'NONE', #74444 ) ; +#59847 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11770, 'distance_accuracy_value', 'NONE'); +#59848 = FACE_OUTER_BOUND ( 'NONE', #45750, .T. ) ; +#59849 = LINE ( 'NONE', #76121, #57854 ) ; +#59850 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59851 = CARTESIAN_POINT ( 'NONE', ( 0.9833223778770081580, -1.000424401669840258, 0.8099999999999898392 ) ) ; +#59852 = VECTOR ( 'NONE', #36001, 1000.000000000000000 ) ; +#59853 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#59854 = LINE ( 'NONE', #90953, #35921 ) ; +#59855 = ORIENTED_EDGE ( 'NONE', *, *, #815, .F. ) ; +#59856 = PLANE ( 'NONE', #7568 ) ; +#59857 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051949811, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#59858 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59859 = ORIENTED_EDGE ( 'NONE', *, *, #31663, .T. ) ; +#59860 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#59861 = CYLINDRICAL_SURFACE ( 'NONE', #56626, 0.009999999999999998473 ) ; +#59862 = ORIENTED_EDGE ( 'NONE', *, *, #86233, .T. ) ; +#59863 = STYLED_ITEM ( 'NONE', ( #53986 ), #73962 ) ; +#59864 = CARTESIAN_POINT ( 'NONE', ( -2.276179938779915091, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#59865 = EDGE_CURVE ( 'NONE', #95866, #2961, #69305, .T. ) ; +#59866 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87797 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71957, #86246, #95398 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59867 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#59868 = SURFACE_STYLE_USAGE ( .BOTH. , #91955 ) ; +#59869 = EDGE_LOOP ( 'NONE', ( #26726, #42759, #26952, #51294 ) ) ; +#59870 = SURFACE_STYLE_FILL_AREA ( #2201 ) ; +#59871 = VERTEX_POINT ( 'NONE', #59154 ) ; +#59872 = FACE_OUTER_BOUND ( 'NONE', #91203, .T. ) ; +#59873 = AXIS2_PLACEMENT_3D ( 'NONE', #24278, #72222, #17071 ) ; +#59874 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59875 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558440262, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#59876 = ORIENTED_EDGE ( 'NONE', *, *, #73290, .F. ) ; +#59877 = EDGE_CURVE ( 'NONE', #84768, #67390, #43277, .T. ) ; +#59878 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43753 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27395, #17690, #74360 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59879 = ORIENTED_EDGE ( 'NONE', *, *, #57844, .F. ) ; +#59880 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59881 = FACE_OUTER_BOUND ( 'NONE', #27542, .T. ) ; +#59882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59883 = ORIENTED_EDGE ( 'NONE', *, *, #27549, .F. ) ; +#59884 = ORIENTED_EDGE ( 'NONE', *, *, #65772, .F. ) ; +#59885 = ORIENTED_EDGE ( 'NONE', *, *, #51641, .F. ) ; +#59886 = SURFACE_STYLE_FILL_AREA ( #92948 ) ; +#59887 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46766 ), #25677 ) ; +#59888 = VECTOR ( 'NONE', #41635, 1000.000000000000000 ) ; +#59889 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90824 ), #94054 ) ; +#59891 = VERTEX_POINT ( 'NONE', #34151 ) ; +#59890 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#59892 = STYLED_ITEM ( 'NONE', ( #85013 ), #41019 ) ; +#59893 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#59894 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#59895 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#59896 = EDGE_LOOP ( 'NONE', ( #18253, #34219, #16308, #61997 ) ) ; +#59897 = FILL_AREA_STYLE_COLOUR ( '', #92843 ) ; +#59898 = PRESENTATION_STYLE_ASSIGNMENT (( #91987 ) ) ; +#59899 = CLOSED_SHELL ( 'NONE', ( #67139, #41393, #812, #39438, #745, #79949 ) ) ; +#59900 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#59901 = ORIENTED_EDGE ( 'NONE', *, *, #97955, .T. ) ; +#59902 = EDGE_CURVE ( 'NONE', #51854, #25227, #41326, .T. ) ; +#59903 = VECTOR ( 'NONE', #11958, 1000.000000000000227 ) ; +#59904 = CYLINDRICAL_SURFACE ( 'NONE', #92087, 0.2000000000000005107 ) ; +#59905 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8299999999999999600 ) ) ; +#59906 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25627 ), #7584 ) ; +#59907 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59908 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59909 = CARTESIAN_POINT ( 'NONE', ( 1.765390738874589971, -1.428263396816370046, 0.8100000000000000533 ) ) ; +#59911 = FILL_AREA_STYLE_COLOUR ( '', #7302 ) ; +#59910 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#59912 = CARTESIAN_POINT ( 'NONE', ( -1.087888467490099043, -1.167561955042019539, 0.8099999999998646061 ) ) ; +#59913 = SURFACE_SIDE_STYLE ('',( #67024 ) ) ; +#59914 = ORIENTED_EDGE ( 'NONE', *, *, #90545, .T. ) ; +#59915 = CARTESIAN_POINT ( 'NONE', ( 0.5096387987012980236, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#59917 = CARTESIAN_POINT ( 'NONE', ( 1.571641772371880075, -1.354501511147599979, 0.8100000000000010525 ) ) ; +#59916 = CARTESIAN_POINT ( 'NONE', ( 0.4538094727981990539, -1.016713352587220065, 0.8100000000000000533 ) ) ; +#59918 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#59919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59920 = ADVANCED_FACE ( 'NONE', ( #42300 ), #89738, .T. ) ; +#59921 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999961697, -0.02000000000000000042 ) ) ; +#59922 = EDGE_CURVE ( 'NONE', #80553, #83102, #19806, .T. ) ; +#59923 = PRESENTATION_STYLE_ASSIGNMENT (( #83379 ) ) ; +#59924 = VECTOR ( 'NONE', #45655, 1000.000000000000000 ) ; +#59925 = EDGE_LOOP ( 'NONE', ( #33733, #67398, #98551, #41259 ) ) ; +#59926 = SURFACE_STYLE_USAGE ( .BOTH. , #28733 ) ; +#59927 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#59928 = ORIENTED_EDGE ( 'NONE', *, *, #99341, .F. ) ; +#59929 = CIRCLE ( 'NONE', #74623, 0.009999999999999998473 ) ; +#59930 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59932 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#59931 = FILL_AREA_STYLE_COLOUR ( '', #86582 ) ; +#59933 = CARTESIAN_POINT ( 'NONE', ( 1.655510330387720330, -0.9679977428869780409, 0.8100000000000000533 ) ) ; +#59934 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50520, #97411, #58681, #89783 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#59935 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#59936 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#59937 = ADVANCED_FACE ( 'NONE', ( #43774 ), #13063, .T. ) ; +#59938 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49384 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13606, #76972, #85639 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#59939 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#59940 = SURFACE_SIDE_STYLE ('',( #51248 ) ) ; +#59941 = ORIENTED_EDGE ( 'NONE', *, *, #5152, .F. ) ; +#59942 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59943 = STYLED_ITEM ( 'NONE', ( #15927 ), #55313 ) ; +#59944 = DIRECTION ( 'NONE', ( -0.7071067811865504593, -0.7071067811865445751, 0.000000000000000000 ) ) ; +#59945 = PRESENTATION_STYLE_ASSIGNMENT (( #36436 ) ) ; +#59946 = CARTESIAN_POINT ( 'NONE', ( 0.9886343406507150933, -1.414598001867640065, 0.8300000000000010703 ) ) ; +#59947 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#59948 = SURFACE_STYLE_FILL_AREA ( #45052 ) ; +#59949 = PLANE ( 'NONE', #9870 ) ; +#59950 = FACE_OUTER_BOUND ( 'NONE', #21792, .T. ) ; +#59951 = LINE ( 'NONE', #74236, #98948 ) ; +#59952 = PRESENTATION_STYLE_ASSIGNMENT (( #60448 ) ) ; +#59953 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59954 = ADVANCED_FACE ( 'NONE', ( #99791 ), #53956, .T. ) ; +#59955 = STYLED_ITEM ( 'NONE', ( #16616 ), #17143 ) ; +#59956 = SURFACE_STYLE_USAGE ( .BOTH. , #3786 ) ; +#59957 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2868 ) ) ; +#59958 = EDGE_LOOP ( 'NONE', ( #62839, #79184, #84888, #24959 ) ) ; +#59959 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59960 = VERTEX_POINT ( 'NONE', #85089 ) ; +#59961 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#59962 = CARTESIAN_POINT ( 'NONE', ( 1.062208424706029941, -1.030374455384980070, 0.8299999999999999600 ) ) ; +#59963 = FACE_OUTER_BOUND ( 'NONE', #26700, .T. ) ; +#59964 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#59965 = STYLED_ITEM ( 'NONE', ( #18487 ), #16291 ) ; +#59966 = PRESENTATION_STYLE_ASSIGNMENT (( #99142 ) ) ; +#59967 = CIRCLE ( 'NONE', #97427, 0.009999999999999998473 ) ; +#59968 = LINE ( 'NONE', #52778, #9199 ) ; +#59969 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#59970 = CARTESIAN_POINT ( 'NONE', ( 0.4595287982601125587, -0.9164889766897266199, 0.8099999999999998312 ) ) ; +#59971 = CLOSED_SHELL ( 'NONE', ( #100110, #85805, #56322, #3560, #32448, #55313 ) ) ; +#59972 = ORIENTED_EDGE ( 'NONE', *, *, #41036, .T. ) ; +#59973 = SURFACE_SIDE_STYLE ('',( #28777 ) ) ; +#59974 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59975 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59976 = VERTEX_POINT ( 'NONE', #32374 ) ; +#59977 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59978 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#59979 = ADVANCED_FACE ( 'NONE', ( #15097 ), #6894, .T. ) ; +#59980 = STYLED_ITEM ( 'NONE', ( #9679 ), #49883 ) ; +#59981 = CARTESIAN_POINT ( 'NONE', ( -1.237444333805499896, -1.426518300252259897, 0.8299999999999999600 ) ) ; +#59982 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#59983 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#59984 = ORIENTED_EDGE ( 'NONE', *, *, #94691, .T. ) ; +#59985 = CARTESIAN_POINT ( 'NONE', ( 3.539405124874955622, 7.720788124874957248, 0.8991599999999999593 ) ) ; +#59987 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#59986 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#59988 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#59989 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8199999999999999512 ) ) ; +#59990 = CARTESIAN_POINT ( 'NONE', ( 1.608893861054889962, -1.000931601726380071, 0.8099999999999994982 ) ) ; +#59991 = ADVANCED_FACE ( 'NONE', ( #63537 ), #94627, .T. ) ; +#59992 = ORIENTED_EDGE ( 'NONE', *, *, #71246, .T. ) ; +#59993 = SURFACE_STYLE_USAGE ( .BOTH. , #12405 ) ; +#59994 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#59995 = FILL_AREA_STYLE ('',( #81472 ) ) ; +#59996 = STYLED_ITEM ( 'NONE', ( #12852 ), #74501 ) ; +#59997 = ORIENTED_EDGE ( 'NONE', *, *, #26816, .T. ) ; +#59998 = ORIENTED_EDGE ( 'NONE', *, *, #75592, .T. ) ; +#60000 = ORIENTED_EDGE ( 'NONE', *, *, #38468, .T. ) ; +#59999 = SURFACE_STYLE_USAGE ( .BOTH. , #59519 ) ; +#60001 = AXIS2_PLACEMENT_3D ( 'NONE', #2423, #9974, #64700 ) ; +#60002 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28979, 'distance_accuracy_value', 'NONE'); +#60003 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333316872, -1.699999999999999956, 0.000000000000000000 ) ) ; +#60005 = CARTESIAN_POINT ( 'NONE', ( -1.263740750452060135, -1.495173285438690103, 0.8100000000000000533 ) ) ; +#60004 = SURFACE_SIDE_STYLE ('',( #91110 ) ) ; +#60006 = FILL_AREA_STYLE ('',( #68613 ) ) ; +#60007 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#60008 = EDGE_LOOP ( 'NONE', ( #55840, #32049, #68505, #87822 ) ) ; +#60009 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60010 = ORIENTED_EDGE ( 'NONE', *, *, #1401, .T. ) ; +#60011 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.300000000000000711, 0.000000000000000000 ) ) ; +#60012 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50339, #4811, #27842, #5285 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60013 = SURFACE_SIDE_STYLE ('',( #58523 ) ) ; +#60014 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#60015 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.5000000000000006661, 0.1829999999999659954 ) ) ; +#60016 = ORIENTED_EDGE ( 'NONE', *, *, #91539, .T. ) ; +#60017 = ORIENTED_EDGE ( 'NONE', *, *, #87737, .T. ) ; +#60018 = EDGE_CURVE ( 'NONE', #51935, #87602, #96635, .T. ) ; +#60019 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84466 ) ) ; +#60020 = CARTESIAN_POINT ( 'NONE', ( -0.6761799387799138916, 3.099999999999989875, 0.000000000000000000 ) ) ; +#60021 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60022 = CIRCLE ( 'NONE', #27422, 0.2000000000000000944 ) ; +#60023 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68123 ) ) ; +#60024 = LINE ( 'NONE', #44642, #63702 ) ; +#60025 = STYLED_ITEM ( 'NONE', ( #75637 ), #16390 ) ; +#60026 = FACE_OUTER_BOUND ( 'NONE', #20891, .T. ) ; +#60027 = VERTEX_POINT ( 'NONE', #80864 ) ; +#60029 = VECTOR ( 'NONE', #44230, 1000.000000000000000 ) ; +#60028 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#60030 = EDGE_LOOP ( 'NONE', ( #64166, #44750, #3513, #95865 ) ) ; +#60031 = SURFACE_STYLE_USAGE ( .BOTH. , #58538 ) ; +#60032 = CLOSED_SHELL ( 'NONE', ( #51504, #11702, #48016, #22558, #1136, #96600 ) ) ; +#60033 = SURFACE_SIDE_STYLE ('',( #14489 ) ) ; +#60034 = EDGE_CURVE ( 'NONE', #22813, #67140, #54743, .T. ) ; +#60035 = CIRCLE ( 'NONE', #63239, 0.1000000000000000472 ) ; +#60036 = FILL_AREA_STYLE_COLOUR ( '', #93776 ) ; +#60037 = EDGE_CURVE ( 'NONE', #86756, #36263, #10804, .T. ) ; +#60038 = AXIS2_PLACEMENT_3D ( 'NONE', #25878, #50864, #82010 ) ; +#60039 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35622 ), #22540 ) ; +#60041 = ADVANCED_FACE ( 'NONE', ( #2744 ), #65503, .T. ) ; +#60040 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#60042 = FILL_AREA_STYLE ('',( #99689 ) ) ; +#60043 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#60044 = CARTESIAN_POINT ( 'NONE', ( 1.322240070112479904, -1.010360997253880067, 0.8299999999999999600 ) ) ; +#60045 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666659946, 2.299999999999999822, 0.000000000000000000 ) ) ; +#60046 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2955 ) ) ; +#60047 = ORIENTED_EDGE ( 'NONE', *, *, #77508, .F. ) ; +#60048 = LINE ( 'NONE', #91154, #87271 ) ; +#60049 = CYLINDRICAL_SURFACE ( 'NONE', #35082, 0.05000000000000012768 ) ; +#60051 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.123820061220065281, 0.000000000000000000 ) ) ; +#60050 = PRESENTATION_STYLE_ASSIGNMENT (( #12972 ) ) ; +#60052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1555, 'distance_accuracy_value', 'NONE'); +#60053 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60054 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#60055 = EDGE_CURVE ( 'NONE', #64141, #71358, #34905, .T. ) ; +#60056 = LINE ( 'NONE', #65672, #89245 ) ; +#60057 = FACE_OUTER_BOUND ( 'NONE', #64480, .T. ) ; +#60058 = PLANE ( 'NONE', #91757 ) ; +#60059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42119 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60515, #44151, #21678 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60060 = VERTEX_POINT ( 'NONE', #27245 ) ; +#60061 = FILL_AREA_STYLE ('',( #99238 ) ) ; +#60063 = EDGE_CURVE ( 'NONE', #14561, #10057, #9799, .T. ) ; +#60062 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999017, 0.8648700000000000276 ) ) ; +#60064 = SURFACE_STYLE_USAGE ( .BOTH. , #30352 ) ; +#60065 = PRESENTATION_STYLE_ASSIGNMENT (( #6810 ) ) ; +#60066 = CARTESIAN_POINT ( 'NONE', ( -0.1098982853935999981, -1.445363849546990043, 0.8100000000000000533 ) ) ; +#60067 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #27000, .NOT_KNOWN. ) ; +#60068 = PRESENTATION_STYLE_ASSIGNMENT (( #84502 ) ) ; +#60069 = SURFACE_STYLE_FILL_AREA ( #29872 ) ; +#60070 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65135 ) ) ; +#60071 = VECTOR ( 'NONE', #25589, 1000.000000000000114 ) ; +#60072 = SURFACE_SIDE_STYLE ('',( #74359 ) ) ; +#60073 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#60074 = SURFACE_STYLE_USAGE ( .BOTH. , #37574 ) ; +#60075 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#60076 = EDGE_CURVE ( 'NONE', #74415, #46606, #41057, .T. ) ; +#60077 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60078 = VECTOR ( 'NONE', #8564, 1000.000000000000000 ) ; +#60079 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60080 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#60081 = EDGE_CURVE ( 'NONE', #83136, #63924, #56889, .T. ) ; +#60082 = PLANE ( 'NONE', #735 ) ; +#60083 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61669 ) ) ; +#60084 = PRESENTATION_STYLE_ASSIGNMENT (( #22751 ) ) ; +#60085 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54420, #92182, #85537 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60086 = EDGE_CURVE ( 'NONE', #4210, #62535, #37411, .T. ) ; +#60087 = VECTOR ( 'NONE', #66937, 1000.000000000000000 ) ; +#60088 = FACE_OUTER_BOUND ( 'NONE', #67697, .T. ) ; +#60089 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8100000000000001643 ) ) ; +#60090 = PLANE ( 'NONE', #52482 ) ; +#60091 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60092 = CARTESIAN_POINT ( 'NONE', ( -0.9365963522183331502, -1.249140550102370018, 0.8100000000000000533 ) ) ; +#60093 = ORIENTED_EDGE ( 'NONE', *, *, #89090, .T. ) ; +#60094 = PRODUCT_DEFINITION ( 'δ֪', '', #66586, #78003 ) ; +#60096 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46990 ) ) ; +#60095 = SURFACE_SIDE_STYLE ('',( #59601 ) ) ; +#60097 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60099 = SURFACE_STYLE_USAGE ( .BOTH. , #20234 ) ; +#60098 = VECTOR ( 'NONE', #8674, 1000.000000000000000 ) ; +#60100 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.800000000000000711, 0.000000000000000000 ) ) ; +#60101 = VECTOR ( 'NONE', #38763, 1000.000000000000000 ) ; +#60102 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#60103 = EDGE_CURVE ( 'NONE', #84076, #61927, #83357, .T. ) ; +#60104 = ORIENTED_EDGE ( 'NONE', *, *, #28768, .F. ) ; +#60105 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60106 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60107 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14385 ) ) ; +#60108 = ORIENTED_EDGE ( 'NONE', *, *, #28790, .F. ) ; +#60109 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60110 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.100000000000000089, 0.000000000000000000 ) ) ; +#60111 = VECTOR ( 'NONE', #43716, 1000.000000000000000 ) ; +#60112 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#60113 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60114 = CLOSED_SHELL ( 'NONE', ( #13528, #25867, #83638, #15181, #5319, #81533 ) ) ; +#60115 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60116 = EDGE_CURVE ( 'NONE', #54417, #69987, #89996, .T. ) ; +#60117 = ORIENTED_EDGE ( 'NONE', *, *, #5821, .F. ) ; +#60118 = ORIENTED_EDGE ( 'NONE', *, *, #1833, .F. ) ; +#60119 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60120 = ORIENTED_EDGE ( 'NONE', *, *, #22757, .F. ) ; +#60121 = FILL_AREA_STYLE_COLOUR ( '', #3749 ) ; +#60122 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49147 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41824, #42326, #92268 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60123 = EDGE_CURVE ( 'NONE', #10043, #17448, #51724, .T. ) ; +#60124 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#60125 = CARTESIAN_POINT ( 'NONE', ( -0.08340097402597419773, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#60126 = STYLED_ITEM ( 'NONE', ( #22242 ), #15200 ) ; +#60127 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #81200, #58257 ) ; +#60128 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81261 ) ) ; +#60130 = ORIENTED_EDGE ( 'NONE', *, *, #21606, .F. ) ; +#60129 = ORIENTED_EDGE ( 'NONE', *, *, #35202, .T. ) ; +#60131 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14408 ), #51948 ) ; +#60132 = EDGE_LOOP ( 'NONE', ( #12791, #9786, #83735, #3484, #37652, #1498 ) ) ; +#60133 = SURFACE_STYLE_USAGE ( .BOTH. , #61114 ) ; +#60134 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57704, 'distance_accuracy_value', 'NONE'); +#60135 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.000000000000000000 ) ) ; +#60136 = CARTESIAN_POINT ( 'NONE', ( 1.353223433754789928, -0.9315058289328710384, 0.8100000000000000533 ) ) ; +#60137 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60138 = ADVANCED_FACE ( 'NONE', ( #73629 ), #27187, .F. ) ; +#60139 = CARTESIAN_POINT ( 'NONE', ( -1.175853632737690058, -0.8847374564574109757, 0.8299999999999999600 ) ) ; +#60140 = ORIENTED_EDGE ( 'NONE', *, *, #85125, .F. ) ; +#60141 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#60142 = ORIENTED_EDGE ( 'NONE', *, *, #64340, .F. ) ; +#60143 = ORIENTED_EDGE ( 'NONE', *, *, #81182, .T. ) ; +#60144 = EDGE_CURVE ( 'NONE', #62323, #96032, #99072, .T. ) ; +#60145 = CARTESIAN_POINT ( 'NONE', ( 1.258996483356980001, -1.238505293396390039, 0.8100000000000000533 ) ) ; +#60146 = STYLED_ITEM ( 'NONE', ( #42376 ), #92480 ) ; +#60147 = VECTOR ( 'NONE', #54008, 1000.000000000000000 ) ; +#60149 = LINE ( 'NONE', #99787, #53181 ) ; +#60148 = FACE_OUTER_BOUND ( 'NONE', #5559, .T. ) ; +#60150 = LINE ( 'NONE', #20285, #79872 ) ; +#60151 = ORIENTED_EDGE ( 'NONE', *, *, #24074, .T. ) ; +#60152 = VECTOR ( 'NONE', #40397, 1000.000000000000000 ) ; +#60153 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60154 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60155 = STYLED_ITEM ( 'NONE', ( #3036 ), #91824 ) ; +#60156 = FILL_AREA_STYLE ('',( #44270 ) ) ; +#60157 = PRESENTATION_STYLE_ASSIGNMENT (( #83107 ) ) ; +#60158 = VERTEX_POINT ( 'NONE', #67016 ) ; +#60159 = FACE_OUTER_BOUND ( 'NONE', #42850, .T. ) ; +#60160 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#60161 = EDGE_LOOP ( 'NONE', ( #14880, #80002, #85441, #55401 ) ) ; +#60162 = ORIENTED_EDGE ( 'NONE', *, *, #42153, .F. ) ; +#60163 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60165 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95723 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65579, #25798, #64585 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60164 = FACE_OUTER_BOUND ( 'NONE', #55479, .T. ) ; +#60166 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60167 = AXIS2_PLACEMENT_3D ( 'NONE', #84672, #7986, #14687 ) ; +#60168 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60169 = EDGE_CURVE ( 'NONE', #62535, #50947, #68875, .T. ) ; +#60170 = VECTOR ( 'NONE', #30104, 1000.000000000000000 ) ; +#60171 = SURFACE_STYLE_FILL_AREA ( #12073 ) ; +#60172 = EDGE_CURVE ( 'NONE', #6650, #56416, #28714, .T. ) ; +#60173 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#60174 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60175 = STYLED_ITEM ( 'NONE', ( #69230 ), #17915 ) ; +#60176 = ORIENTED_EDGE ( 'NONE', *, *, #1929, .F. ) ; +#60177 = AXIS2_PLACEMENT_3D ( 'NONE', #58583, #73868, #58083 ) ; +#60178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43802 ) ) ; +#60179 = FILL_AREA_STYLE ('',( #4002 ) ) ; +#60180 = ORIENTED_EDGE ( 'NONE', *, *, #14706, .F. ) ; +#60181 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60182 = CARTESIAN_POINT ( 'NONE', ( -0.07193707439540279747, -0.9683984092875530525, 0.8100000000000000533 ) ) ; +#60183 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#60184 = VECTOR ( 'NONE', #67572, 1000.000000000000000 ) ; +#60185 = PRESENTATION_STYLE_ASSIGNMENT (( #53494 ) ) ; +#60186 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60187 = LINE ( 'NONE', #97887, #87562 ) ; +#60188 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60189 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60190 = VERTEX_POINT ( 'NONE', #11798 ) ; +#60191 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60192 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#60193 = CARTESIAN_POINT ( 'NONE', ( 0.2967604117379429862, -0.9084949572282049468, 0.8299999999999999600 ) ) ; +#60194 = PRESENTATION_STYLE_ASSIGNMENT (( #46162 ) ) ; +#60195 = PRESENTATION_STYLE_ASSIGNMENT (( #58185 ) ) ; +#60196 = AXIS2_PLACEMENT_3D ( 'NONE', #48621, #88405, #10707 ) ; +#60197 = CARTESIAN_POINT ( 'NONE', ( 1.850801046367029912, -1.212495751768599916, 0.8100000000000000533 ) ) ; +#60198 = PRESENTATION_STYLE_ASSIGNMENT (( #91779 ) ) ; +#60199 = PRESENTATION_STYLE_ASSIGNMENT (( #52507 ) ) ; +#60200 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60201 = ADVANCED_FACE ( 'NONE', ( #44034 ), #97621, .T. ) ; +#60202 = PRESENTATION_STYLE_ASSIGNMENT (( #36696 ) ) ; +#60203 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60204 = EDGE_LOOP ( 'NONE', ( #35859, #34383, #62151, #45626, #25161, #97961 ) ) ; +#60205 = SURFACE_SIDE_STYLE ('',( #99374 ) ) ; +#60206 = PLANE ( 'NONE', #38893 ) ; +#60207 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#60208 = EDGE_LOOP ( 'NONE', ( #37666, #12, #57535, #43721 ) ) ; +#60209 = SURFACE_STYLE_USAGE ( .BOTH. , #75987 ) ; +#60210 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#60211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60212 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85018 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25417, #80041, #88194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60213 = CARTESIAN_POINT ( 'NONE', ( 1.418232044022499805, -1.061283632817239697, 0.8099999999999513145 ) ) ; +#60214 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#60215 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60216 = STYLED_ITEM ( 'NONE', ( #67186 ), #31899 ) ; +#60217 = SURFACE_SIDE_STYLE ('',( #67323 ) ) ; +#60218 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #73414, #10006, #3466, #2455, #26447, #33607, #49938, #1450, #32595, #56084, #81084, #57103, #34618 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000012490, 0.2500000000000024980, 0.3750000000000037748, 0.4375000000000037192, 0.5000000000000036637, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60219 = VERTEX_POINT ( 'NONE', #36891 ) ; +#60220 = SURFACE_STYLE_FILL_AREA ( #44335 ) ; +#60221 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74833 ) ) ; +#60222 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60223 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86269 ) ) ; +#60224 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8648700000000000276 ) ) ; +#60225 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60226 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60228 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#60227 = VECTOR ( 'NONE', #57356, 1000.000000000000000 ) ; +#60229 = ADVANCED_FACE ( 'NONE', ( #98092 ), #75683, .T. ) ; +#60230 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70013 ) ) ; +#60231 = SURFACE_STYLE_USAGE ( .BOTH. , #58724 ) ; +#60232 = ORIENTED_EDGE ( 'NONE', *, *, #86390, .F. ) ; +#60233 = VERTEX_POINT ( 'NONE', #7152 ) ; +#60234 = VECTOR ( 'NONE', #54894, 1000.000000000000000 ) ; +#60235 = ORIENTED_EDGE ( 'NONE', *, *, #75778, .T. ) ; +#60236 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#60237 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60238 = FACE_OUTER_BOUND ( 'NONE', #29588, .T. ) ; +#60239 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#60240 = PRESENTATION_STYLE_ASSIGNMENT (( #44845 ) ) ; +#60241 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60242 = CARTESIAN_POINT ( 'NONE', ( -0.3840663679600159752, -0.9878352835667890686, 0.8100000000000000533 ) ) ; +#60243 = CARTESIAN_POINT ( 'NONE', ( -1.183862409742999944, -0.9551946040733080290, 0.8100000000000000533 ) ) ; +#60244 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60245 = VECTOR ( 'NONE', #95815, 1000.000000000000000 ) ; +#60247 = ORIENTED_EDGE ( 'NONE', *, *, #51469, .T. ) ; +#60246 = ORIENTED_EDGE ( 'NONE', *, *, #98328, .F. ) ; +#60248 = EDGE_CURVE ( 'NONE', #73427, #88894, #23080, .T. ) ; +#60249 = AXIS2_PLACEMENT_3D ( 'NONE', #10234, #95568, #17970 ) ; +#60250 = ORIENTED_EDGE ( 'NONE', *, *, #90145, .T. ) ; +#60251 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82526, #12476, #98254, #43690 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60252 = SURFACE_STYLE_FILL_AREA ( #37739 ) ; +#60253 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8966, 'distance_accuracy_value', 'NONE'); +#60255 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#60254 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60256 = AXIS2_PLACEMENT_3D ( 'NONE', #63420, #94505, #9180 ) ; +#60257 = VERTEX_POINT ( 'NONE', #39382 ) ; +#60258 = EDGE_CURVE ( 'NONE', #65640, #15315, #6660, .T. ) ; +#60259 = ORIENTED_EDGE ( 'NONE', *, *, #56347, .F. ) ; +#60260 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60261 = CARTESIAN_POINT ( 'NONE', ( 11.79841287512498837, 7.155102875124987882, 0.8648700000000000276 ) ) ; +#60262 = LINE ( 'NONE', #20405, #31196 ) ; +#60263 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79786 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34318, #26642, #88914 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60264 = EDGE_LOOP ( 'NONE', ( #94734, #36624, #37271, #37591 ) ) ; +#60265 = VERTEX_POINT ( 'NONE', #32254 ) ; +#60266 = EDGE_CURVE ( 'NONE', #63443, #84427, #32836, .T. ) ; +#60267 = LINE ( 'NONE', #51606, #33076 ) ; +#60271 = ADVANCED_FACE ( 'NONE', ( #100542 ), #69504, .F. ) ; +#60270 = EDGE_LOOP ( 'NONE', ( #48697, #91865, #44768, #93420 ) ) ; +#60269 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18339 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62606, #15047, #22259 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60268 = LINE ( 'NONE', #18903, #6948 ) ; +#60272 = EDGE_CURVE ( 'NONE', #35369, #85285, #8655, .T. ) ; +#60273 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60274 = ORIENTED_EDGE ( 'NONE', *, *, #32743, .F. ) ; +#60275 = FILL_AREA_STYLE_COLOUR ( '', #81107 ) ; +#60276 = LINE ( 'NONE', #89869, #90077 ) ; +#60277 = ORIENTED_EDGE ( 'NONE', *, *, #43678, .F. ) ; +#60278 = ORIENTED_EDGE ( 'NONE', *, *, #27662, .F. ) ; +#60279 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 1.166666666666666741, 0.000000000000000000 ) ) ; +#60280 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60281 = FACE_OUTER_BOUND ( 'NONE', #26587, .T. ) ; +#60282 = ADVANCED_FACE ( 'NONE', ( #46527 ), #47556, .F. ) ; +#60283 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84721 ), #17813 ) ; +#60284 = FACE_OUTER_BOUND ( 'NONE', #47809, .T. ) ; +#60285 = EDGE_CURVE ( 'NONE', #97109, #53546, #41930, .T. ) ; +#60286 = SURFACE_SIDE_STYLE ('',( #30571 ) ) ; +#60287 = PRESENTATION_STYLE_ASSIGNMENT (( #46915 ) ) ; +#60288 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#60289 = VECTOR ( 'NONE', #54919, 1000.000000000000000 ) ; +#60290 = CARTESIAN_POINT ( 'NONE', ( 0.1802163075021840088, -1.026304639009830044, 0.8300000000000020695 ) ) ; +#60291 = ORIENTED_EDGE ( 'NONE', *, *, #1427, .T. ) ; +#60292 = CARTESIAN_POINT ( 'NONE', ( -1.139646564935959949, -1.515470133326519919, 0.8299999999999999600 ) ) ; +#60293 = ORIENTED_EDGE ( 'NONE', *, *, #93547, .T. ) ; +#60294 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60295 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9386 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27947, #82561, #46208 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60296 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#60297 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#60298 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60299 = FILL_AREA_STYLE_COLOUR ( '', #65020 ) ; +#60300 = CARTESIAN_POINT ( 'NONE', ( 1.726282678897220091, -1.159841243706410063, 0.8100000000000000533 ) ) ; +#60301 = FILL_AREA_STYLE_COLOUR ( '', #31943 ) ; +#60302 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60303 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96171 ), #52199 ) ; +#60304 = PRESENTATION_STYLE_ASSIGNMENT (( #22463 ) ) ; +#60305 = LINE ( 'NONE', #6578, #88699 ) ; +#60306 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22807 ), #79899 ) ; +#60307 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60308 = SURFACE_STYLE_FILL_AREA ( #21967 ) ; +#60309 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60310 = AXIS2_PLACEMENT_3D ( 'NONE', #27007, #94885, #72429 ) ; +#60312 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60313 = LINE ( 'NONE', #37802, #21191 ) ; +#60314 = EDGE_CURVE ( 'NONE', #46200, #65564, #79211, .T. ) ; +#60315 = STYLED_ITEM ( 'NONE', ( #13576 ), #75764 ) ; +#60316 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9693 ), #50552 ) ; +#60317 = EDGE_CURVE ( 'NONE', #39491, #44555, #18411, .T. ) ; +#60318 = EDGE_LOOP ( 'NONE', ( #6860, #1385, #21788, #5548 ) ) ; +#60319 = CARTESIAN_POINT ( 'NONE', ( -1.074341942140480066, -1.437631519369750199, 0.8299999999999999600 ) ) ; +#60320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55631, 'distance_accuracy_value', 'NONE'); +#60321 = SURFACE_SIDE_STYLE ('',( #75602 ) ) ; +#60322 = SURFACE_SIDE_STYLE ('',( #99974 ) ) ; +#60323 = SURFACE_STYLE_USAGE ( .BOTH. , #21979 ) ; +#60324 = PLANE ( 'NONE', #25886 ) ; +#60325 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#60326 = SURFACE_SIDE_STYLE ('',( #66940 ) ) ; +#60327 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26674 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40835, #64800, #2021 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60328 = LINE ( 'NONE', #91431, #23103 ) ; +#60329 = FACE_OUTER_BOUND ( 'NONE', #23260, .T. ) ; +#60330 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60331 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#60332 = ORIENTED_EDGE ( 'NONE', *, *, #1868, .T. ) ; +#60333 = SURFACE_STYLE_FILL_AREA ( #3661 ) ; +#60334 = ORIENTED_EDGE ( 'NONE', *, *, #22860, .T. ) ; +#60335 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.008431457505076185577, -0.2458578643762690530 ) ) ; +#60336 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24013, 'distance_accuracy_value', 'NONE'); +#60337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10361, 'distance_accuracy_value', 'NONE'); +#60338 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24406 ) ) ; +#60339 = FILL_AREA_STYLE_COLOUR ( '', #87402 ) ; +#60340 = LINE ( 'NONE', #83300, #51264 ) ; +#60341 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 8.031915000000001470, 0.8648700000000000276 ) ) ; +#60342 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60343 = AXIS2_PLACEMENT_3D ( 'NONE', #96040, #51020, #82157 ) ; +#60344 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60345 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#60346 = LINE ( 'NONE', #50672, #43987 ) ; +#60347 = SURFACE_STYLE_USAGE ( .BOTH. , #83803 ) ; +#60348 = ORIENTED_EDGE ( 'NONE', *, *, #70218, .F. ) ; +#60349 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60350 = SURFACE_STYLE_USAGE ( .BOTH. , #75152 ) ; +#60351 = ORIENTED_EDGE ( 'NONE', *, *, #1902, .T. ) ; +#60352 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#60353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74865 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16958, #40997, #25662 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60354 = LINE ( 'NONE', #22505, #33797 ) ; +#60355 = VERTEX_POINT ( 'NONE', #56770 ) ; +#60356 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73386 ) ) ; +#60357 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14517 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26225, #80345, #57375 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60358 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60359 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#60360 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#60362 = VERTEX_POINT ( 'NONE', #94503 ) ; +#60361 = ORIENTED_EDGE ( 'NONE', *, *, #14652, .F. ) ; +#60363 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12942 ), #16264 ) ; +#60364 = LINE ( 'NONE', #8119, #68389 ) ; +#60365 = STYLED_ITEM ( 'NONE', ( #30274 ), #85497 ) ; +#60366 = STYLED_ITEM ( 'NONE', ( #61342 ), #92370 ) ; +#60367 = VERTEX_POINT ( 'NONE', #94997 ) ; +#60368 = SURFACE_STYLE_FILL_AREA ( #36360 ) ; +#60369 = VECTOR ( 'NONE', #17025, 1000.000000000000000 ) ; +#60371 = CARTESIAN_POINT ( 'NONE', ( -0.5298581286778389909, -0.9738248771264079728, 0.8100000000000000533 ) ) ; +#60370 = FILL_AREA_STYLE ('',( #53185 ) ) ; +#60372 = VERTEX_POINT ( 'NONE', #33769 ) ; +#60373 = ORIENTED_EDGE ( 'NONE', *, *, #53794, .F. ) ; +#60374 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24522 ) ) ; +#60375 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60376 = FILL_AREA_STYLE ('',( #76155 ) ) ; +#60377 = SURFACE_STYLE_FILL_AREA ( #5166 ) ; +#60378 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60380 = PRESENTATION_STYLE_ASSIGNMENT (( #52206 ) ) ; +#60379 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60381 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60382 = ORIENTED_EDGE ( 'NONE', *, *, #35937, .F. ) ; +#60383 = VERTEX_POINT ( 'NONE', #63900 ) ; +#60384 = VERTEX_POINT ( 'NONE', #86875 ) ; +#60385 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1500000000000000500 ) ) ; +#60386 = VECTOR ( 'NONE', #56430, 1000.000000000000000 ) ; +#60387 = AXIS2_PLACEMENT_3D ( 'NONE', #98319, #96861, #5424 ) ; +#60389 = ORIENTED_EDGE ( 'NONE', *, *, #92981, .T. ) ; +#60388 = SURFACE_SIDE_STYLE ('',( #99057 ) ) ; +#60390 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60391 = EDGE_CURVE ( 'NONE', #86832, #98314, #81255, .T. ) ; +#60392 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.299999999999999822, 0.1829999999999500082 ) ) ; +#60393 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#60394 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60395 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#60396 = VERTEX_POINT ( 'NONE', #34790 ) ; +#60397 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60398 = ORIENTED_EDGE ( 'NONE', *, *, #49290, .T. ) ; +#60399 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60400 = STYLED_ITEM ( 'NONE', ( #48443 ), #10814 ) ; +#60401 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42204, #35058, #18676, #48861 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60402 = EDGE_CURVE ( 'NONE', #28703, #67038, #49092, .T. ) ; +#60403 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66919 ), #6502 ) ; +#60405 = EDGE_LOOP ( 'NONE', ( #68798, #52227, #40222, #7509 ) ) ; +#60404 = SURFACE_STYLE_USAGE ( .BOTH. , #60892 ) ; +#60406 = CARTESIAN_POINT ( 'NONE', ( 1.367410627668359968, -0.9444486738239200596, 0.8299999999999998490 ) ) ; +#60407 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60409 = FACE_OUTER_BOUND ( 'NONE', #80678, .T. ) ; +#60408 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60410 = CARTESIAN_POINT ( 'NONE', ( -0.9531279601788141820, -1.229871795159534820, 0.8099999999998187539 ) ) ; +#60411 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60412 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60413 = VERTEX_POINT ( 'NONE', #87870 ) ; +#60414 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64327 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82314, #5145, #36846 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60415 = LINE ( 'NONE', #91514, #92224 ) ; +#60416 = CARTESIAN_POINT ( 'NONE', ( 1.148671667572580102, -1.140452398731560013, 0.8300000000000022915 ) ) ; +#60417 = LINE ( 'NONE', #91519, #94206 ) ; +#60418 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60419 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60420 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18 ), #40878 ) ; +#60421 = CARTESIAN_POINT ( 'NONE', ( 1.676663961038960204, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#60422 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999334, -0.5799999999999999600 ) ) ; +#60423 = VERTEX_POINT ( 'NONE', #2618 ) ; +#60424 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#60425 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#60426 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62016 ), #29418 ) ; +#60427 = VECTOR ( 'NONE', #41790, 1000.000000000000000 ) ; +#60428 = PLANE ( 'NONE', #27207 ) ; +#60429 = ORIENTED_EDGE ( 'NONE', *, *, #22509, .T. ) ; +#60430 = CIRCLE ( 'NONE', #19580, 1.462498829941430323 ) ; +#60431 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, -0.7999999999999999334 ) ) ; +#60433 = LINE ( 'NONE', #22595, #70569 ) ; +#60432 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#60434 = FACE_BOUND ( 'NONE', #42542, .T. ) ; +#60435 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60436 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#60437 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000005884, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#60438 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#60439 = EDGE_CURVE ( 'NONE', #51828, #48067, #9179, .T. ) ; +#60440 = ORIENTED_EDGE ( 'NONE', *, *, #54950, .T. ) ; +#60441 = AXIS2_PLACEMENT_3D ( 'NONE', #41279, #35135, #19264 ) ; +#60442 = LINE ( 'NONE', #84385, #33223 ) ; +#60443 = FACE_OUTER_BOUND ( 'NONE', #80995, .T. ) ; +#60444 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91385 ) ) ; +#60445 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#60446 = PLANE ( 'NONE', #58861 ) ; +#60447 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60448 = SURFACE_STYLE_USAGE ( .BOTH. , #36935 ) ; +#60449 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61040, 'distance_accuracy_value', 'NONE'); +#60450 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60451 = VECTOR ( 'NONE', #18566, 1000.000000000000000 ) ; +#60452 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60453 = VECTOR ( 'NONE', #7691, 1000.000000000000000 ) ; +#60454 = ORIENTED_EDGE ( 'NONE', *, *, #98275, .T. ) ; +#60455 = FILL_AREA_STYLE_COLOUR ( '', #5656 ) ; +#60456 = ORIENTED_EDGE ( 'NONE', *, *, #62809, .F. ) ; +#60457 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#60459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78956, 'distance_accuracy_value', 'NONE'); +#60458 = VECTOR ( 'NONE', #2852, 1000.000000000000000 ) ; +#60460 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12662, 'distance_accuracy_value', 'NONE'); +#60461 = CARTESIAN_POINT ( 'NONE', ( 1.101360327800479988, -0.9762538161110779766, 0.8100000000000000533 ) ) ; +#60462 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999578 ) ) ; +#60463 = CARTESIAN_POINT ( 'NONE', ( -0.9164863243573180274, -1.381526214478759895, 0.8299999999999981837 ) ) ; +#60464 = FACE_OUTER_BOUND ( 'NONE', #43763, .T. ) ; +#60465 = LINE ( 'NONE', #16436, #63551 ) ; +#60466 = ORIENTED_EDGE ( 'NONE', *, *, #19240, .F. ) ; +#60467 = FILL_AREA_STYLE ('',( #36958 ) ) ; +#60469 = ADVANCED_FACE ( 'NONE', ( #40933 ), #11178, .T. ) ; +#60468 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#60470 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82490, 'distance_accuracy_value', 'NONE'); +#60471 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31138 ), #3381 ) ; +#60472 = EDGE_LOOP ( 'NONE', ( #16635, #92803, #77767, #14212 ) ) ; +#60473 = EDGE_CURVE ( 'NONE', #21325, #12693, #55741, .T. ) ; +#60474 = FILL_AREA_STYLE ('',( #67089 ) ) ; +#60475 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60476 = SURFACE_STYLE_FILL_AREA ( #5273 ) ; +#60477 = ORIENTED_EDGE ( 'NONE', *, *, #29458, .T. ) ; +#60478 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60479 = VECTOR ( 'NONE', #23033, 1000.000000000000000 ) ; +#60480 = SURFACE_SIDE_STYLE ('',( #46085 ) ) ; +#60481 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72324, 'distance_accuracy_value', 'NONE'); +#60482 = LINE ( 'NONE', #21145, #34602 ) ; +#60483 = CARTESIAN_POINT ( 'NONE', ( 1.634048567103849825, -0.9784189978443859070, 0.8099999999999994982 ) ) ; +#60484 = EDGE_CURVE ( 'NONE', #62116, #48821, #50112, .T. ) ; +#60485 = EDGE_LOOP ( 'NONE', ( #24353, #49576, #16947, #36229, #6300 ) ) ; +#60486 = EDGE_CURVE ( 'NONE', #9565, #5291, #33259, .T. ) ; +#60487 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#60488 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60489 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60490 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60491 = CARTESIAN_POINT ( 'NONE', ( 1.498514669629020135, -1.357596283920579960, 0.8300000000000001821 ) ) ; +#60492 = EDGE_LOOP ( 'NONE', ( #17137, #72114, #95926, #67593 ) ) ; +#60493 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60494 = PRODUCT ( 'DesignRootModel', 'DesignRootModel', '', ( #22394 ) ) ; +#60495 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47417 ), #34479 ) ; +#60496 = STYLED_ITEM ( 'NONE', ( #42185 ), #57858 ) ; +#60497 = VERTEX_POINT ( 'NONE', #17898 ) ; +#60500 = ORIENTED_EDGE ( 'NONE', *, *, #13763, .T. ) ; +#60499 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8648700000000000276 ) ) ; +#60498 = AXIS2_PLACEMENT_3D ( 'NONE', #72028, #63870, #64355 ) ; +#60501 = ADVANCED_FACE ( 'NONE', ( #35796 ), #91387, .T. ) ; +#60502 = VECTOR ( 'NONE', #86757, 1000.000000000000000 ) ; +#60503 = FACE_OUTER_BOUND ( 'NONE', #80313, .T. ) ; +#60504 = PRESENTATION_STYLE_ASSIGNMENT (( #29328 ) ) ; +#60505 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.100000000000000089 ) ) ; +#60506 = ORIENTED_EDGE ( 'NONE', *, *, #30565, .T. ) ; +#60507 = SURFACE_SIDE_STYLE ('',( #20150 ) ) ; +#60508 = EDGE_LOOP ( 'NONE', ( #32850, #19870, #72033, #35786, #94830 ) ) ; +#60509 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60510 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#60511 = SURFACE_STYLE_USAGE ( .BOTH. , #29339 ) ; +#60512 = FILL_AREA_STYLE ('',( #99193 ) ) ; +#60513 = VERTEX_POINT ( 'NONE', #36771 ) ; +#60514 = AXIS2_PLACEMENT_3D ( 'NONE', #38939, #45054, #31776 ) ; +#60516 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60517 = ORIENTED_EDGE ( 'NONE', *, *, #73585, .F. ) ; +#60518 = ADVANCED_FACE ( 'NONE', ( #19434 ), #89383, .T. ) ; +#60519 = LINE ( 'NONE', #91616, #58170 ) ; +#60520 = FACE_OUTER_BOUND ( 'NONE', #39484, .T. ) ; +#60521 = VECTOR ( 'NONE', #65221, 1000.000000000000000 ) ; +#60522 = LINE ( 'NONE', #20673, #83289 ) ; +#60523 = AXIS2_PLACEMENT_3D ( 'NONE', #26102, #88367, #49082 ) ; +#60524 = CARTESIAN_POINT ( 'NONE', ( 0.2283082038525930113, -1.316727038456209975, 0.8299999999999982947 ) ) ; +#60525 = ORIENTED_EDGE ( 'NONE', *, *, #28200, .F. ) ; +#60526 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999990841, 0.8199999999999998401, -0.04999999999999998890 ) ) ; +#60527 = VERTEX_POINT ( 'NONE', #76062 ) ; +#60528 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60530 = PRESENTATION_STYLE_ASSIGNMENT (( #52848 ) ) ; +#60529 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60531 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58948 ) ) ; +#60532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60533 = ADVANCED_FACE ( 'NONE', ( #4117 ), #97519, .F. ) ; +#60534 = PLANE ( 'NONE', #47427 ) ; +#60535 = PLANE ( 'NONE', #88664 ) ; +#60536 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41009 ) ) ; +#60538 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#60537 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31142 ) ) ; +#60539 = SURFACE_STYLE_FILL_AREA ( #22202 ) ; +#60540 = CARTESIAN_POINT ( 'NONE', ( 1.333992163213469917, -1.033922635360990050, 0.8100000000000000533 ) ) ; +#60541 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60542 = VERTEX_POINT ( 'NONE', #46913 ) ; +#60543 = EDGE_CURVE ( 'NONE', #27567, #79320, #60773, .T. ) ; +#60544 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60545 = FACE_OUTER_BOUND ( 'NONE', #30807, .T. ) ; +#60547 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60546 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60548 = AXIS2_PLACEMENT_3D ( 'NONE', #42136, #34494, #82442 ) ; +#60549 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.09999999999999961697, -0.02000000000001260145 ) ) ; +#60550 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8648700000000000276 ) ) ; +#60551 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60552 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#60553 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#60554 = ADVANCED_FACE ( 'NONE', ( #76555 ), #23989, .T. ) ; +#60555 = ORIENTED_EDGE ( 'NONE', *, *, #35035, .F. ) ; +#60556 = PRESENTATION_STYLE_ASSIGNMENT (( #37064 ) ) ; +#60557 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#60558 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#60559 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90202 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31864, #9311, #71684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60561 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#60562 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#60563 = CYLINDRICAL_SURFACE ( 'NONE', #59873, 0.04999999999999991257 ) ; +#60564 = PRESENTATION_STYLE_ASSIGNMENT (( #21227 ) ) ; +#60565 = STYLED_ITEM ( 'NONE', ( #83020 ), #95455 ) ; +#60566 = FILL_AREA_STYLE_COLOUR ( '', #11379 ) ; +#60567 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#60568 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#60569 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#60570 = VECTOR ( 'NONE', #88635, 1000.000000000000000 ) ; +#60571 = PLANE ( 'NONE', #4945 ) ; +#60572 = FILL_AREA_STYLE_COLOUR ( '', #92686 ) ; +#60573 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89227, 'distance_accuracy_value', 'NONE'); +#60574 = SURFACE_SIDE_STYLE ('',( #53891 ) ) ; +#60575 = PRESENTATION_STYLE_ASSIGNMENT (( #68183 ) ) ; +#60576 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#60577 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#60578 = CARTESIAN_POINT ( 'NONE', ( -0.9118498257241719473, -1.330101555947649894, 0.8100000000000000533 ) ) ; +#60579 = VERTEX_POINT ( 'NONE', #86234 ) ; +#60580 = AXIS2_PLACEMENT_3D ( 'NONE', #89113, #81485, #73791 ) ; +#60581 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85001, 'distance_accuracy_value', 'NONE'); +#60582 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60583 = PLANE ( 'NONE', #1408 ) ; +#60584 = CARTESIAN_POINT ( 'NONE', ( -0.06269022549541880540, -0.9718760589866800581, 0.8300000000000002931 ) ) ; +#60585 = EDGE_CURVE ( 'NONE', #32262, #72845, #100912, .T. ) ; +#60586 = SURFACE_STYLE_FILL_AREA ( #22257 ) ; +#60587 = SURFACE_SIDE_STYLE ('',( #29420 ) ) ; +#60588 = VECTOR ( 'NONE', #22993, 1000.000000000000114 ) ; +#60589 = STYLED_ITEM ( 'NONE', ( #6385 ), #2474 ) ; +#60590 = PRESENTATION_STYLE_ASSIGNMENT (( #36602 ) ) ; +#60591 = ORIENTED_EDGE ( 'NONE', *, *, #30122, .F. ) ; +#60592 = LINE ( 'NONE', #67698, #8955 ) ; +#60593 = SURFACE_STYLE_USAGE ( .BOTH. , #21254 ) ; +#60594 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61913, 'distance_accuracy_value', 'NONE'); +#60595 = CARTESIAN_POINT ( 'NONE', ( -0.03242561202523040059, -1.422222704560690110, 0.8300000000000006262 ) ) ; +#60596 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#60597 = EDGE_CURVE ( 'NONE', #63516, #74161, #37777, .T. ) ; +#60598 = ORIENTED_EDGE ( 'NONE', *, *, #4533, .F. ) ; +#60599 = EDGE_LOOP ( 'NONE', ( #68353, #73449, #26990, #35892, #19828 ) ) ; +#60600 = EDGE_CURVE ( 'NONE', #16395, #41260, #61777, .T. ) ; +#60601 = LINE ( 'NONE', #89706, #32519 ) ; +#60602 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60603 = VERTEX_POINT ( 'NONE', #54098 ) ; +#60604 = STYLED_ITEM ( 'NONE', ( #36938 ), #51997 ) ; +#60605 = ADVANCED_FACE ( 'NONE', ( #92839 ), #62274, .T. ) ; +#60606 = CARTESIAN_POINT ( 'NONE', ( 0.4283467773376269938, -1.261010674219189998, 0.8299999999999999600 ) ) ; +#60607 = LINE ( 'NONE', #3940, #92467 ) ; +#60608 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8991599999999999593 ) ) ; +#60609 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#60610 = FILL_AREA_STYLE ('',( #53933 ) ) ; +#60611 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #87371, #25542 ) ; +#60612 = ORIENTED_EDGE ( 'NONE', *, *, #47008, .T. ) ; +#60613 = ORIENTED_EDGE ( 'NONE', *, *, #63547, .F. ) ; +#60614 = FILL_AREA_STYLE_COLOUR ( '', #60609 ) ; +#60615 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998900047, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#60616 = EDGE_CURVE ( 'NONE', #93243, #80183, #65271, .T. ) ; +#60617 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7935, #85629, #6931, #47329 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60618 = PRESENTATION_STYLE_ASSIGNMENT (( #36634 ) ) ; +#60619 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #39016, #31341, #63026, #24227 ), + ( #55378, #72676, #19036, #56888 ), + ( #66022, #58402, #26736, #88502 ), + ( #67015, #43031, #20046, #97132 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606879705, 0.6476030138606879705, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606879705, 0.6476030138606879705, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#60620 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.6999999999999992895, 0.1829999999999789573 ) ) ; +#60621 = EDGE_CURVE ( 'NONE', #63509, #53981, #10049, .T. ) ; +#60622 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60623 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75859 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43373, #12670, #74026 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60624 = CARTESIAN_POINT ( 'NONE', ( -1.305325210527780166, -0.9264544496121620565, 0.8299999999999999600 ) ) ; +#60625 = VERTEX_POINT ( 'NONE', #63300 ) ; +#60626 = ORIENTED_EDGE ( 'NONE', *, *, #92590, .T. ) ; +#60627 = ORIENTED_EDGE ( 'NONE', *, *, #453, .T. ) ; +#60628 = CARTESIAN_POINT ( 'NONE', ( 1.137573705260860102, -1.210702855844099979, 0.8100000000000000533 ) ) ; +#60629 = STYLED_ITEM ( 'NONE', ( #100311 ), #86793 ) ; +#60630 = EDGE_CURVE ( 'NONE', #1845, #71556, #41317, .T. ) ; +#60631 = ADVANCED_FACE ( 'NONE', ( #40305 ), #41809, .F. ) ; +#60632 = FACE_OUTER_BOUND ( 'NONE', #69624, .T. ) ; +#60634 = EDGE_LOOP ( 'NONE', ( #42395, #6207, #51599, #58876 ) ) ; +#60633 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60635 = AXIS2_PLACEMENT_3D ( 'NONE', #718, #220, #31877 ) ; +#60636 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#60637 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8648700000000000276 ) ) ; +#60638 = DIRECTION ( 'NONE', ( 3.614007241618339896E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60639 = VERTEX_POINT ( 'NONE', #80124 ) ; +#60640 = PRESENTATION_STYLE_ASSIGNMENT (( #43285 ) ) ; +#60641 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -2.824738166141190008E-16 ) ) ; +#60642 = VERTEX_POINT ( 'NONE', #72418 ) ; +#60643 = ORIENTED_EDGE ( 'NONE', *, *, #15919, .T. ) ; +#60644 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60645 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60646 = FILL_AREA_STYLE_COLOUR ( '', #10485 ) ; +#60647 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5121 ), #50889 ) ; +#60648 = PRESENTATION_STYLE_ASSIGNMENT (( #99340 ) ) ; +#60649 = FACE_OUTER_BOUND ( 'NONE', #13180, .T. ) ; +#60650 = SURFACE_STYLE_FILL_AREA ( #91267 ) ; +#60651 = ORIENTED_EDGE ( 'NONE', *, *, #27724, .F. ) ; +#60652 = EDGE_CURVE ( 'NONE', #75316, #10757, #72944, .T. ) ; +#60653 = STYLED_ITEM ( 'NONE', ( #74400 ), #2492 ) ; +#60654 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60655 = ORIENTED_EDGE ( 'NONE', *, *, #6409, .F. ) ; +#60656 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#60657 = CARTESIAN_POINT ( 'NONE', ( -0.03785612751057330916, -0.9872600217210630857, 0.8299999999999999600 ) ) ; +#60658 = CARTESIAN_POINT ( 'NONE', ( 1.068409529932820012, -1.093211113524890088, 0.8299999999999999600 ) ) ; +#60659 = PRESENTATION_STYLE_ASSIGNMENT (( #22330 ) ) ; +#60660 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32592, #72895, #80075, #41269, #47898, #79052, #9007, #71379, #1445, #43250, #89713, #58112, #42266, #36123, #49936, #97820, #43742, #50943, #97343 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.199810243541582030E-05, 4.278690227043873535E-05, 6.252165198476553997E-05, 8.158361054740497279E-05, 0.0001002151390316336469, 0.0001186497156152640223, 0.0001368610957251347447, 0.0001552754567345477721, 0.0001739329553027156637, 0.0001929318924837881261, 0.0002122658542286259874, 0.0002322243066156582964, 0.0002525346056374900335, 0.0002728217849409556267, 0.0002931775127341202866, 0.0003136925383507654062 ), + .UNSPECIFIED. ) ; +#60661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#60662 = LINE ( 'NONE', #35687, #62600 ) ; +#60663 = EDGE_CURVE ( 'NONE', #51408, #70194, #95892, .T. ) ; +#60664 = VERTEX_POINT ( 'NONE', #1493 ) ; +#60665 = LINE ( 'NONE', #91765, #47715 ) ; +#60666 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60667 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#60668 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8648700000000000276 ) ) ; +#60669 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60670 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000812, -0.1400000000000008737 ) ) ; +#60671 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60672 = EDGE_CURVE ( 'NONE', #14404, #86914, #18278, .T. ) ; +#60673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60674 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60675 = SURFACE_SIDE_STYLE ('',( #15146 ) ) ; +#60676 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000081, 0.8991599999999999593 ) ) ; +#60677 = SURFACE_STYLE_USAGE ( .BOTH. , #75978 ) ; +#60678 = SURFACE_SIDE_STYLE ('',( #73979 ) ) ; +#60679 = EDGE_CURVE ( 'NONE', #80299, #61238, #24999, .T. ) ; +#60681 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38071 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #544, #63387, #39866 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60680 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#60682 = SURFACE_STYLE_USAGE ( .BOTH. , #97905 ) ; +#60683 = CARTESIAN_POINT ( 'NONE', ( 1.296768031029680079, -0.9834456900322131601, 0.8299999999999995159 ) ) ; +#60684 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57090, 'distance_accuracy_value', 'NONE'); +#60685 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60686 = CARTESIAN_POINT ( 'NONE', ( -0.9453606081591535704, -1.009524776188984063, 0.8099999999999809575 ) ) ; +#60687 = ORIENTED_EDGE ( 'NONE', *, *, #74626, .F. ) ; +#60688 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60689 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60690 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60691 = AXIS2_PLACEMENT_3D ( 'NONE', #42691, #98238, #35563 ) ; +#60692 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11069, 'distance_accuracy_value', 'NONE'); +#60693 = STYLED_ITEM ( 'NONE', ( #29801 ), #34484 ) ; +#60694 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#60695 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 3.614007241618339896E-16 ) ) ; +#60696 = SURFACE_SIDE_STYLE ('',( #68321 ) ) ; +#60697 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69077 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38147, #60633, #5433 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60698 = EDGE_CURVE ( 'NONE', #49566, #4908, #52738, .T. ) ; +#60699 = STYLED_ITEM ( 'NONE', ( #29364 ), #86963 ) ; +#60700 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47639 ) ) ; +#60701 = STYLED_ITEM ( 'NONE', ( #375 ), #96063 ) ; +#60702 = ORIENTED_EDGE ( 'NONE', *, *, #22388, .T. ) ; +#60703 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #68335, #89242 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #14070 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#60704 = CARTESIAN_POINT ( 'NONE', ( 0.6761799387799150018, -3.099999999999980105, 0.000000000000000000 ) ) ; +#60705 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60706 = FILL_AREA_STYLE_COLOUR ( '', #23622 ) ; +#60707 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60708 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60709 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31706, 'distance_accuracy_value', 'NONE'); +#60710 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82685, 'distance_accuracy_value', 'NONE'); +#60711 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60712 = AXIS2_PLACEMENT_3D ( 'NONE', #69894, #100913, #5577 ) ; +#60713 = ADVANCED_FACE ( 'NONE', ( #977 ), #94385, .T. ) ; +#60714 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60715 = ORIENTED_EDGE ( 'NONE', *, *, #19705, .F. ) ; +#60716 = ORIENTED_EDGE ( 'NONE', *, *, #23695, .T. ) ; +#60717 = EDGE_CURVE ( 'NONE', #44869, #99146, #36670, .T. ) ; +#60718 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13310 ) ) ; +#60719 = ORIENTED_EDGE ( 'NONE', *, *, #2275, .T. ) ; +#60720 = PRESENTATION_STYLE_ASSIGNMENT (( #14181 ) ) ; +#60721 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#60722 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #22819 ) ; +#60723 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.600000000000000089, -12.44500000000000028 ) ) ; +#60724 = CARTESIAN_POINT ( 'NONE', ( -0.4324685231842523292, 1.272232131270036870, 0.8100000000000000533 ) ) ; +#60726 = VERTEX_POINT ( 'NONE', #81631 ) ; +#60725 = EDGE_LOOP ( 'NONE', ( #25355, #53368, #80355, #67450 ) ) ; +#60727 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2048 ) ) ; +#60728 = ORIENTED_EDGE ( 'NONE', *, *, #47191, .F. ) ; +#60729 = CARTESIAN_POINT ( 'NONE', ( 1.572445103981990222, -0.9412361261466359874, 0.8099999999999981659 ) ) ; +#60730 = EDGE_CURVE ( 'NONE', #78170, #94847, #28011, .T. ) ; +#60732 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#60731 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998900047, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#60733 = VERTEX_POINT ( 'NONE', #50499 ) ; +#60734 = VERTEX_POINT ( 'NONE', #11569 ) ; +#60735 = PRESENTATION_STYLE_ASSIGNMENT (( #30536 ) ) ; +#60736 = EDGE_CURVE ( 'NONE', #40957, #51854, #91265, .T. ) ; +#60737 = FILL_AREA_STYLE_COLOUR ( '', #52911 ) ; +#60738 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96216 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31894, #30871, #13100 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60739 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01085786437626898131, -0.1500000000000000222 ) ) ; +#60740 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60742 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#60741 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#60743 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666633301, -2.299999999999999822, 3.495651678169922342E-76 ) ) ; +#60744 = VERTEX_POINT ( 'NONE', #75446 ) ; +#60745 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7117, #90978, #44481, #75648 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60746 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, 0.000000000000000000 ) ) ; +#60747 = AXIS2_PLACEMENT_3D ( 'NONE', #32620, #100889, #62759 ) ; +#60748 = ORIENTED_EDGE ( 'NONE', *, *, #86361, .F. ) ; +#60749 = ORIENTED_EDGE ( 'NONE', *, *, #61332, .F. ) ; +#60750 = EDGE_CURVE ( 'NONE', #35535, #38717, #66291, .T. ) ; +#60751 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#60752 = EDGE_CURVE ( 'NONE', #29025, #35264, #64190, .T. ) ; +#60753 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#60756 = ORIENTED_EDGE ( 'NONE', *, *, #19067, .F. ) ; +#60755 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74192, 'distance_accuracy_value', 'NONE'); +#60754 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.149999999999990585, 0.000000000000000000 ) ) ; +#60757 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60758 = PLANE ( 'NONE', #98614 ) ; +#60759 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60760 = VECTOR ( 'NONE', #3777, 1000.000000000000000 ) ; +#60761 = ORIENTED_EDGE ( 'NONE', *, *, #18804, .T. ) ; +#60762 = LINE ( 'NONE', #98944, #61569 ) ; +#60763 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60764 = ORIENTED_EDGE ( 'NONE', *, *, #8376, .T. ) ; +#60765 = ORIENTED_EDGE ( 'NONE', *, *, #5866, .F. ) ; +#60766 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#60767 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60768 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67554 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97935, #73520, #5529 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60769 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87196 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18567, #43062, #82879 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60770 = CIRCLE ( 'NONE', #13434, 0.01000000000000002623 ) ; +#60771 = FACE_OUTER_BOUND ( 'NONE', #2989, .T. ) ; +#60772 = AXIS2_PLACEMENT_3D ( 'NONE', #14352, #31227, #92965 ) ; +#60773 = LINE ( 'NONE', #7033, #21681 ) ; +#60774 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96584 ), #73810 ) ; +#60775 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#60776 = VECTOR ( 'NONE', #66095, 1000.000000000000000 ) ; +#60777 = FILL_AREA_STYLE_COLOUR ( '', #54590 ) ; +#60778 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#60779 = ORIENTED_EDGE ( 'NONE', *, *, #41570, .T. ) ; +#60780 = EDGE_CURVE ( 'NONE', #66452, #2598, #42805, .T. ) ; +#60781 = CARTESIAN_POINT ( 'NONE', ( -0.9882503141469709540, -1.475119686261340046, 0.8299999999999999600 ) ) ; +#60782 = ORIENTED_EDGE ( 'NONE', *, *, #40328, .T. ) ; +#60783 = VECTOR ( 'NONE', #62895, 1000.000000000000000 ) ; +#60784 = LINE ( 'NONE', #44407, #53001 ) ; +#60785 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#60786 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60787 = CARTESIAN_POINT ( 'NONE', ( 9.125548750249976138, 2.700330249750026113, 0.8991599999999999593 ) ) ; +#60788 = SURFACE_SIDE_STYLE ('',( #99946 ) ) ; +#60789 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#60790 = CARTESIAN_POINT ( 'NONE', ( 1.726282678897220091, -1.159841243706410063, 0.8299999999999999600 ) ) ; +#60792 = ADVANCED_FACE ( 'NONE', ( #35674 ), #51502, .T. ) ; +#60791 = FILL_AREA_STYLE ('',( #44905 ) ) ; +#60793 = VECTOR ( 'NONE', #61160, 1000.000000000000000 ) ; +#60794 = SURFACE_STYLE_USAGE ( .BOTH. , #13736 ) ; +#60795 = CARTESIAN_POINT ( 'NONE', ( -1.394603015216079989, -1.309512843728070086, 0.8300000000000024025 ) ) ; +#60796 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60797 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60798 = VECTOR ( 'NONE', #63961, 1000.000000000000000 ) ; +#60799 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60800 = EDGE_CURVE ( 'NONE', #44001, #91498, #43796, .T. ) ; +#60801 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60802 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#60803 = SURFACE_STYLE_FILL_AREA ( #21970 ) ; +#60804 = ADVANCED_FACE ( 'NONE', ( #36171 ), #67274, .T. ) ; +#60805 = CIRCLE ( 'NONE', #55930, 0.3000000000000000444 ) ; +#60806 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60807 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88952, 'distance_accuracy_value', 'NONE'); +#60808 = EDGE_LOOP ( 'NONE', ( #89638, #31194, #33801, #91059 ) ) ; +#60809 = SURFACE_STYLE_FILL_AREA ( #36312 ) ; +#60810 = FACE_OUTER_BOUND ( 'NONE', #20030, .T. ) ; +#60811 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#60812 = FILL_AREA_STYLE_COLOUR ( '', #22351 ) ; +#60813 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.400000000000000355, 0.000000000000000000 ) ) ; +#60814 = SURFACE_STYLE_USAGE ( .BOTH. , #37333 ) ; +#60815 = STYLED_ITEM ( 'NONE', ( #90025 ), #87776 ) ; +#60816 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8648700000000000276 ) ) ; +#60817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24903 ), #41212 ) ; +#60818 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.35000000000000142 ) ) ; +#60819 = PRESENTATION_STYLE_ASSIGNMENT (( #59335 ) ) ; +#60820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60821 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#60822 = EDGE_CURVE ( 'NONE', #89369, #89490, #44775, .T. ) ; +#60823 = EDGE_CURVE ( 'NONE', #91646, #37871, #22842, .T. ) ; +#60824 = ORIENTED_EDGE ( 'NONE', *, *, #23177, .F. ) ; +#60825 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60826 = VECTOR ( 'NONE', #22835, 1000.000000000000000 ) ; +#60827 = ORIENTED_EDGE ( 'NONE', *, *, #41503, .T. ) ; +#60828 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60829 = ADVANCED_FACE ( 'NONE', ( #15117 ), #66944, .F. ) ; +#60830 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60831 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60832 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60833 = PRESENTATION_STYLE_ASSIGNMENT (( #82304 ) ) ; +#60834 = VECTOR ( 'NONE', #49354, 1000.000000000000000 ) ; +#60835 = LINE ( 'NONE', #91940, #37066 ) ; +#60836 = SURFACE_STYLE_USAGE ( .BOTH. , #38841 ) ; +#60837 = VERTEX_POINT ( 'NONE', #33012 ) ; +#60838 = STYLED_ITEM ( 'NONE', ( #31937 ), #20977 ) ; +#60839 = FACE_OUTER_BOUND ( 'NONE', #32864, .T. ) ; +#60840 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#60841 = FILL_AREA_STYLE_COLOUR ( '', #67266 ) ; +#60842 = EDGE_LOOP ( 'NONE', ( #68258, #99547, #76317, #13027 ) ) ; +#60843 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8991599999999999593 ) ) ; +#60844 = ADVANCED_FACE ( 'NONE', ( #24884 ), #25378, .F. ) ; +#60845 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17577 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14251, #16279, #45408 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60846 = VERTEX_POINT ( 'NONE', #70798 ) ; +#60847 = EDGE_CURVE ( 'NONE', #11668, #30183, #87637, .T. ) ; +#60848 = VECTOR ( 'NONE', #33657, 1000.000000000000000 ) ; +#60849 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60850 = VECTOR ( 'NONE', #83302, 1000.000000000000000 ) ; +#60851 = SURFACE_STYLE_FILL_AREA ( #93925 ) ; +#60852 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60853 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60854 = LINE ( 'NONE', #29669, #680 ) ; +#60856 = EDGE_LOOP ( 'NONE', ( #16158, #69634, #65800, #60016 ) ) ; +#60855 = ORIENTED_EDGE ( 'NONE', *, *, #68326, .F. ) ; +#60857 = AXIS2_PLACEMENT_3D ( 'NONE', #63280, #94368, #24483 ) ; +#60858 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#60859 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39694 ) ) ; +#60860 = VERTEX_POINT ( 'NONE', #32007 ) ; +#60861 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#60862 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2109 ), #99851 ) ; +#60863 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#60864 = VERTEX_POINT ( 'NONE', #71823 ) ; +#60865 = VERTEX_POINT ( 'NONE', #1877 ) ; +#60866 = CARTESIAN_POINT ( 'NONE', ( 2.123820061220085265, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#60867 = PRESENTATION_STYLE_ASSIGNMENT (( #67474 ) ) ; +#60868 = SURFACE_SIDE_STYLE ('',( #29685 ) ) ; +#60869 = STYLED_ITEM ( 'NONE', ( #17097 ), #67156 ) ; +#60870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60871 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#60872 = ORIENTED_EDGE ( 'NONE', *, *, #72930, .T. ) ; +#60873 = ORIENTED_EDGE ( 'NONE', *, *, #29369, .T. ) ; +#60874 = FILL_AREA_STYLE_COLOUR ( '', #37241 ) ; +#60875 = ORIENTED_EDGE ( 'NONE', *, *, #13021, .F. ) ; +#60876 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#60877 = EDGE_CURVE ( 'NONE', #62983, #69571, #83827, .T. ) ; +#60878 = VERTEX_POINT ( 'NONE', #24372 ) ; +#60879 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#60880 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60881 = FILL_AREA_STYLE_COLOUR ( '', #41588 ) ; +#60882 = VECTOR ( 'NONE', #21144, 1000.000000000000000 ) ; +#60883 = EDGE_LOOP ( 'NONE', ( #62870, #19930, #23879, #34756 ) ) ; +#60884 = EDGE_CURVE ( 'NONE', #15979, #85776, #16639, .T. ) ; +#60885 = LINE ( 'NONE', #68986, #20647 ) ; +#60886 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1833333333333333481, 0.000000000000000000 ) ) ; +#60887 = ORIENTED_EDGE ( 'NONE', *, *, #34668, .T. ) ; +#60888 = FILL_AREA_STYLE_COLOUR ( '', #54669 ) ; +#60889 = CARTESIAN_POINT ( 'NONE', ( 3.383841999999999572, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#60890 = AXIS2_PLACEMENT_3D ( 'NONE', #35555, #73832, #97277 ) ; +#60891 = VECTOR ( 'NONE', #68564, 1000.000000000000000 ) ; +#60893 = ORIENTED_EDGE ( 'NONE', *, *, #42494, .F. ) ; +#60892 = SURFACE_SIDE_STYLE ('',( #82361 ) ) ; +#60894 = CARTESIAN_POINT ( 'NONE', ( 1.283545161422839920, -0.8955552045491329549, 0.8299999999999998490 ) ) ; +#60895 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#60897 = CARTESIAN_POINT ( 'NONE', ( 1.516559913281009919, -1.413990021526319918, 0.8299999999999999600 ) ) ; +#60896 = PRESENTATION_STYLE_ASSIGNMENT (( #15886 ) ) ; +#60898 = EDGE_CURVE ( 'NONE', #16986, #94347, #57031, .T. ) ; +#60899 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60900 = VERTEX_POINT ( 'NONE', #41188 ) ; +#60901 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#60902 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#60904 = CARTESIAN_POINT ( 'NONE', ( 1.321985133225566544, -1.418839292875715197, 0.8099999999997266054 ) ) ; +#60903 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#60905 = LINE ( 'NONE', #4738, #42059 ) ; +#60906 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#60908 = EDGE_CURVE ( 'NONE', #26843, #15215, #78966, .T. ) ; +#60907 = FACE_OUTER_BOUND ( 'NONE', #14103, .T. ) ; +#60909 = VECTOR ( 'NONE', #25329, 1000.000000000000000 ) ; +#60910 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90261 ), #18452 ) ; +#60911 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#60912 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01499999999999998557, 0.1400000000000000133 ) ) ; +#60913 = VERTEX_POINT ( 'NONE', #63673 ) ; +#60914 = AXIS2_PLACEMENT_3D ( 'NONE', #34666, #21319, #96894 ) ; +#60915 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12304, #28704, #90999, #28223, #21060, #89507 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 4 ), + ( 0.000000000000000000, 0.5000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#60916 = FACE_OUTER_BOUND ( 'NONE', #33, .T. ) ; +#60917 = SURFACE_SIDE_STYLE ('',( #82870 ) ) ; +#60918 = ORIENTED_EDGE ( 'NONE', *, *, #6310, .T. ) ; +#60919 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#60920 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#60922 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24858 ) ) ; +#60921 = FILL_AREA_STYLE ('',( #29738 ) ) ; +#60923 = EDGE_CURVE ( 'NONE', #25468, #26141, #9415, .T. ) ; +#60924 = LINE ( 'NONE', #91039, #45270 ) ; +#60925 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#60926 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57679 ) ) ; +#60927 = LINE ( 'NONE', #54258, #75442 ) ; +#60928 = EDGE_CURVE ( 'NONE', #60513, #58513, #18149, .T. ) ; +#60929 = ORIENTED_EDGE ( 'NONE', *, *, #75492, .T. ) ; +#60930 = LINE ( 'NONE', #28749, #99920 ) ; +#60931 = FILL_AREA_STYLE ('',( #52268 ) ) ; +#60932 = CARTESIAN_POINT ( 'NONE', ( 0.9590361231611750359, -1.326636125966530244, 0.8300000000000010703 ) ) ; +#60933 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#60934 = VECTOR ( 'NONE', #59978, 1000.000000000000000 ) ; +#60935 = SURFACE_SIDE_STYLE ('',( #78736 ) ) ; +#60936 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#60937 = FILL_AREA_STYLE ('',( #29753 ) ) ; +#60938 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60939 = EDGE_CURVE ( 'NONE', #8907, #97466, #26664, .T. ) ; +#60940 = SURFACE_SIDE_STYLE ('',( #69032 ) ) ; +#60941 = EDGE_CURVE ( 'NONE', #14799, #39491, #26877, .T. ) ; +#60942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#60943 = FILL_AREA_STYLE ('',( #68050 ) ) ; +#60944 = ORIENTED_EDGE ( 'NONE', *, *, #37076, .T. ) ; +#60945 = ORIENTED_EDGE ( 'NONE', *, *, #57671, .F. ) ; +#60946 = ADVANCED_FACE ( 'NONE', ( #89149 ), #59561, .T. ) ; +#60947 = CARTESIAN_POINT ( 'NONE', ( 1.077065871219029969, -0.9985765647821309710, 0.8100000000000000533 ) ) ; +#60948 = SURFACE_STYLE_USAGE ( .BOTH. , #50792 ) ; +#60949 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8648700000000000276 ) ) ; +#60950 = CARTESIAN_POINT ( 'NONE', ( -1.023967505146820001, -1.493640573211080014, 0.8299999999999991829 ) ) ; +#60951 = DIRECTION ( 'NONE', ( 0.3387340427540269649, -0.000000000000000000, 0.9408821649279537347 ) ) ; +#60952 = VECTOR ( 'NONE', #70612, 1000.000000000000000 ) ; +#60953 = FILL_AREA_STYLE_COLOUR ( '', #19503 ) ; +#60954 = LINE ( 'NONE', #67080, #70514 ) ; +#60955 = VERTEX_POINT ( 'NONE', #34549 ) ; +#60956 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#60957 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.1199999999999999956, 0.6500000000000001332 ) ) ; +#60958 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, 0.2458578643762690530 ) ) ; +#60959 = EDGE_CURVE ( 'NONE', #57096, #39553, #66159, .T. ) ; +#60960 = PRESENTATION_STYLE_ASSIGNMENT (( #29778 ) ) ; +#60961 = ORIENTED_EDGE ( 'NONE', *, *, #63945, .F. ) ; +#60962 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80569 ) ) ; +#60963 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#60964 = ADVANCED_FACE ( 'NONE', ( #18669 ), #74824, .T. ) ; +#60965 = SURFACE_SIDE_STYLE ('',( #23658 ) ) ; +#60966 = CARTESIAN_POINT ( 'NONE', ( -1.275112219867899910, -1.401744930657430110, 0.8299999999999999600 ) ) ; +#60967 = AXIS2_PLACEMENT_3D ( 'NONE', #29609, #21951, #68405 ) ; +#60968 = SURFACE_STYLE_FILL_AREA ( #83930 ) ; +#60969 = ORIENTED_EDGE ( 'NONE', *, *, #95502, .F. ) ; +#60970 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#60971 = PLANE ( 'NONE', #29605 ) ; +#60972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91909 ), #87057 ) ; +#60973 = VERTEX_POINT ( 'NONE', #51864 ) ; +#60974 = VECTOR ( 'NONE', #9945, 1000.000000000000000 ) ; +#60975 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#60976 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#60977 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#60978 = CARTESIAN_POINT ( 'NONE', ( 1.562899685023940055, -1.469666695271939938, 0.8300000000000001821 ) ) ; +#60979 = ORIENTED_EDGE ( 'NONE', *, *, #27860, .T. ) ; +#60980 = SURFACE_STYLE_FILL_AREA ( #23175 ) ; +#60981 = AXIS2_PLACEMENT_3D ( 'NONE', #79869, #71690, #2261 ) ; +#60982 = AXIS2_PLACEMENT_3D ( 'NONE', #61034, #68143, #100684 ) ; +#60983 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93393 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34485, #18615, #10365 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#60984 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100316, 'distance_accuracy_value', 'NONE'); +#60985 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #69438, #75622, #6610, #37832, #68929, #84778, #77122, #54155, #7089, #100480, #30636, #31672, #24564, #9616, #63362, #25055, #93415, #23526, #78147 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.417957774307013855E-05, 2.786330893872813295E-05, 4.109794397677743845E-05, 5.383676549423477688E-05, 6.625423184903269530E-05, 7.847836201925295727E-05, 9.066284592776888043E-05, 0.0001028204189866466011, 0.0001149859491741178006, 0.0001269720978533745088, 0.0001389625930523560187, 0.0001514642992412920089, 0.0001643130881902038888, 0.0001776669893733589991, 0.0001918024004216830117, 0.0002068227363344025287 ), + .UNSPECIFIED. ) ; +#60986 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3906 ) ) ; +#60987 = ORIENTED_EDGE ( 'NONE', *, *, #40728, .F. ) ; +#60989 = ORIENTED_EDGE ( 'NONE', *, *, #824, .F. ) ; +#60988 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#60990 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26476, 'distance_accuracy_value', 'NONE'); +#60991 = AXIS2_PLACEMENT_3D ( 'NONE', #27349, #83480, #13441 ) ; +#60992 = LINE ( 'NONE', #70636, #47497 ) ; +#60994 = CARTESIAN_POINT ( 'NONE', ( -1.241916755955269958, -1.502675929081449979, 0.8299999999999999600 ) ) ; +#60993 = FILL_AREA_STYLE ('',( #100155 ) ) ; +#60995 = CARTESIAN_POINT ( 'NONE', ( 2.818155750249974556, 6.999539249750025505, 0.8648700000000000276 ) ) ; +#60996 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#60997 = ORIENTED_EDGE ( 'NONE', *, *, #70837, .F. ) ; +#60999 = EDGE_CURVE ( 'NONE', #29208, #71441, #65659, .T. ) ; +#60998 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61000 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.123820061220085265, 0.000000000000000000 ) ) ; +#61001 = FILL_AREA_STYLE_COLOUR ( '', #75292 ) ; +#61002 = ORIENTED_EDGE ( 'NONE', *, *, #53440, .F. ) ; +#61003 = CARTESIAN_POINT ( 'NONE', ( 1.436760428889430008, -1.381526214478759895, 0.8100000000000000533 ) ) ; +#61004 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61005 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#61006 = FILL_AREA_STYLE ('',( #46125 ) ) ; +#61007 = EDGE_LOOP ( 'NONE', ( #72379, #80991, #44006, #12337 ) ) ; +#61009 = CARTESIAN_POINT ( 'NONE', ( 4.409146875125044218, 7.671290875125043485, 0.8648700000000000276 ) ) ; +#61008 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61010 = VERTEX_POINT ( 'NONE', #67635 ) ; +#61011 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8705 ) ) ; +#61013 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#61012 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#61014 = PRESENTATION_STYLE_ASSIGNMENT (( #29348 ) ) ; +#61015 = CARTESIAN_POINT ( 'NONE', ( 3.383842000000000017, 7.565224999999999866, 0.8991599999999999593 ) ) ; +#61016 = VECTOR ( 'NONE', #55640, 1000.000000000000000 ) ; +#61017 = LINE ( 'NONE', #22187, #12452 ) ; +#61018 = ORIENTED_EDGE ( 'NONE', *, *, #20236, .T. ) ; +#61019 = CARTESIAN_POINT ( 'NONE', ( 0.1634537337662340106, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#61020 = STYLED_ITEM ( 'NONE', ( #2082 ), #53563 ) ; +#61021 = VERTEX_POINT ( 'NONE', #98718 ) ; +#61022 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61023 = FILL_AREA_STYLE ('',( #99684 ) ) ; +#61024 = PLANE ( 'NONE', #35526 ) ; +#61025 = EDGE_CURVE ( 'NONE', #36117, #98939, #5828, .T. ) ; +#61026 = STYLED_ITEM ( 'NONE', ( #67898 ), #87452 ) ; +#61027 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34993 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29507, #99830, #93255 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61028 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, 0.000000000000000000 ) ) ; +#61029 = SURFACE_STYLE_USAGE ( .BOTH. , #75822 ) ; +#61031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31919 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92902, #93413, #54152 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61030 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#61032 = PRESENTATION_STYLE_ASSIGNMENT (( #37545 ) ) ; +#61033 = SURFACE_SIDE_STYLE ('',( #60539 ) ) ; +#61034 = CARTESIAN_POINT ( 'NONE', ( 8.231457000000000690, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#61035 = VERTEX_POINT ( 'NONE', #52853 ) ; +#61036 = FILL_AREA_STYLE ('',( #68650 ) ) ; +#61037 = SURFACE_SIDE_STYLE ('',( #84983 ) ) ; +#61038 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83842 ), #46250 ) ; +#61041 = FILL_AREA_STYLE ('',( #6798 ) ) ; +#61040 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61039 = PLANE ( 'NONE', #658 ) ; +#61042 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61043 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93933, 'distance_accuracy_value', 'NONE'); +#61044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61045 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61046 = VECTOR ( 'NONE', #2627, 1000.000000000000000 ) ; +#61047 = CARTESIAN_POINT ( 'NONE', ( -1.302508589717060072, -1.365949044099890264, 0.8299999999999998490 ) ) ; +#61048 = FACE_OUTER_BOUND ( 'NONE', #74802, .T. ) ; +#61049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69640 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31778, #7700, #70574 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61050 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 3.110451999999999995, 0.8648700000000000276 ) ) ; +#61051 = ORIENTED_EDGE ( 'NONE', *, *, #74588, .F. ) ; +#61052 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61055 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61054 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64245 ) ) ; +#61053 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61056 = CARTESIAN_POINT ( 'NONE', ( 0.01549768115604830028, -1.336414498567920051, 0.8299999999999999600 ) ) ; +#61057 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21888 ) ) ; +#61058 = PRESENTATION_STYLE_ASSIGNMENT (( #52891 ) ) ; +#61059 = SURFACE_STYLE_FILL_AREA ( #68169 ) ; +#61061 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#61060 = STYLED_ITEM ( 'NONE', ( #97146 ), #61405 ) ; +#61062 = FILL_AREA_STYLE ('',( #23254 ) ) ; +#61063 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61064 = SURFACE_SIDE_STYLE ('',( #52899 ) ) ; +#61065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61066 = PLANE ( 'NONE', #72906 ) ; +#61067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61068 = FACE_OUTER_BOUND ( 'NONE', #83426, .T. ) ; +#61069 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#61070 = FILL_AREA_STYLE_COLOUR ( '', #15355 ) ; +#61071 = EDGE_CURVE ( 'NONE', #66984, #26813, #6785, .T. ) ; +#61072 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61073 = AXIS2_PLACEMENT_3D ( 'NONE', #9301, #40552, #9804 ) ; +#61074 = CYLINDRICAL_SURFACE ( 'NONE', #97608, 0.009999999999999998473 ) ; +#61075 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584400679, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#61076 = AXIS2_PLACEMENT_3D ( 'NONE', #52082, #58747, #59262 ) ; +#61077 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#61078 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61079 = ORIENTED_EDGE ( 'NONE', *, *, #12039, .T. ) ; +#61080 = LINE ( 'NONE', #6364, #4636 ) ; +#61081 = SURFACE_SIDE_STYLE ('',( #68690 ) ) ; +#61082 = CIRCLE ( 'NONE', #46376, 0.009999999999999998473 ) ; +#61083 = CARTESIAN_POINT ( 'NONE', ( 5.130395499499825540, 4.135756500500176180, 0.8991599999999999593 ) ) ; +#61084 = VERTEX_POINT ( 'NONE', #44658 ) ; +#61085 = CARTESIAN_POINT ( 'NONE', ( -0.007896400202255349221, -1.058723197808659977, 0.8300000000000002931 ) ) ; +#61086 = VECTOR ( 'NONE', #98200, 1000.000000000000000 ) ; +#61087 = EDGE_CURVE ( 'NONE', #21831, #75765, #92132, .T. ) ; +#61088 = SURFACE_STYLE_USAGE ( .BOTH. , #69175 ) ; +#61089 = PRESENTATION_STYLE_ASSIGNMENT (( #100246 ) ) ; +#61090 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61091 = ORIENTED_EDGE ( 'NONE', *, *, #47996, .T. ) ; +#61092 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61093 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66129, 'distance_accuracy_value', 'NONE'); +#61094 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.700000000000000178, 1.158998207294579771E-78 ) ) ; +#61095 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4232 ) ) ; +#61096 = STYLED_ITEM ( 'NONE', ( #76567 ), #53871 ) ; +#61097 = ORIENTED_EDGE ( 'NONE', *, *, #67131, .F. ) ; +#61098 = ORIENTED_EDGE ( 'NONE', *, *, #78018, .F. ) ; +#61099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28503 ) ) ; +#61100 = AXIS2_PLACEMENT_3D ( 'NONE', #60558, #61053, #52384 ) ; +#61101 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8299999999999999600 ) ) ; +#61102 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#61103 = ORIENTED_EDGE ( 'NONE', *, *, #97416, .F. ) ; +#61104 = CARTESIAN_POINT ( 'NONE', ( 0.5268964082245309877, -1.158245412001609909, 0.8100000000000000533 ) ) ; +#61105 = STYLED_ITEM ( 'NONE', ( #2239 ), #26646 ) ; +#61106 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61107 = SURFACE_SIDE_STYLE ('',( #29922 ) ) ; +#61108 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #72740, #95683 ), + ( #43097, #2799 ), + ( #56955, #88070 ), + ( #18070, #80931 ), + ( #10351, #41611 ), + ( #65079, #57448 ), + ( #18597, #49786 ), + ( #98638, #13382 ), + ( #59474, #90570 ), + ( #91069, #20606 ), + ( #51781, #22121 ), + ( #12880, #36953 ), + ( #37466, #68061 ), + ( #45552, #35972 ), + ( #99617, #83422 ), + ( #61459, #14412 ), + ( #99143, #6234 ), + ( #83910, #13904 ), + ( #30258, #67560 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07371267057028850489, 0.1427176704673379926, 0.2082134058715000013, 0.2705027277892230186, 0.3304959100989089960, 0.3889789042896930060, 0.4458964732700320122, 0.5023682877331400176, 0.5591912362163320438, 0.6167818134451890089, 0.6762489342310300522, 0.7375288950348040107, 0.8004750105796279991, 0.8650547179286960375, 0.9315767411187479974, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61109 = EDGE_CURVE ( 'NONE', #38282, #16868, #28852, .T. ) ; +#61110 = ORIENTED_EDGE ( 'NONE', *, *, #20516, .T. ) ; +#61111 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61112 = VERTEX_POINT ( 'NONE', #29365 ) ; +#61113 = PRESENTATION_STYLE_ASSIGNMENT (( #1184 ) ) ; +#61114 = SURFACE_SIDE_STYLE ('',( #45232 ) ) ; +#61115 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21950 ), #67558 ) ; +#61117 = AXIS2_PLACEMENT_3D ( 'NONE', #64077, #10344, #50297 ) ; +#61116 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6697, 'distance_accuracy_value', 'NONE'); +#61118 = LINE ( 'NONE', #43754, #45707 ) ; +#61120 = CARTESIAN_POINT ( 'NONE', ( 1.263299480776550077, -0.8906029366306310591, 0.8299999999999999600 ) ) ; +#61119 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61121 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#61122 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#61123 = EDGE_CURVE ( 'NONE', #36462, #88429, #46275, .T. ) ; +#61125 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96942 ), #93632 ) ; +#61124 = VECTOR ( 'NONE', #38498, 1000.000000000000000 ) ; +#61126 = STYLED_ITEM ( 'NONE', ( #48389 ), #98518 ) ; +#61127 = PRESENTATION_STYLE_ASSIGNMENT (( #77927 ) ) ; +#61128 = VERTEX_POINT ( 'NONE', #68642 ) ; +#61130 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61129 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61131 = ORIENTED_EDGE ( 'NONE', *, *, #45896, .T. ) ; +#61132 = VERTEX_POINT ( 'NONE', #37040 ) ; +#61133 = SURFACE_STYLE_USAGE ( .BOTH. , #59656 ) ; +#61135 = LINE ( 'NONE', #84086, #89040 ) ; +#61134 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#61136 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61137 = PRESENTATION_STYLE_ASSIGNMENT (( #43773 ) ) ; +#61138 = ORIENTED_EDGE ( 'NONE', *, *, #83341, .F. ) ; +#61139 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3906 ), #67582 ) ; +#61140 = CARTESIAN_POINT ( 'NONE', ( 9.252827750249974059, 9.700686750249976953, 0.8991599999999999593 ) ) ; +#61141 = DIRECTION ( 'NONE', ( -0.9998998904353922912, 0.01414952675146630492, 0.000000000000000000 ) ) ; +#61142 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61143 = CARTESIAN_POINT ( 'NONE', ( 5.540517124874957844, 8.802661124874957110, 0.8648700000000000276 ) ) ; +#61144 = ORIENTED_EDGE ( 'NONE', *, *, #60847, .F. ) ; +#61146 = PRESENTATION_STYLE_ASSIGNMENT (( #75431 ) ) ; +#61145 = SURFACE_STYLE_FILL_AREA ( #22830 ) ; +#61147 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61148 = ORIENTED_EDGE ( 'NONE', *, *, #27404, .T. ) ; +#61149 = ORIENTED_EDGE ( 'NONE', *, *, #20128, .T. ) ; +#61150 = SURFACE_SIDE_STYLE ('',( #45262 ) ) ; +#61152 = DIRECTION ( 'NONE', ( 0.7071075504167435577, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#61151 = CARTESIAN_POINT ( 'NONE', ( 1.182009071931110045, -1.515071875619850017, 0.8100000000000000533 ) ) ; +#61153 = SURFACE_SIDE_STYLE ('',( #76433 ) ) ; +#61154 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61155 = ADVANCED_FACE ( 'NONE', ( #45146 ), #69111, .T. ) ; +#61156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61157 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61158 = VECTOR ( 'NONE', #94500, 1000.000000000000000 ) ; +#61159 = EDGE_CURVE ( 'NONE', #45876, #5007, #21694, .T. ) ; +#61160 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#61161 = SURFACE_STYLE_FILL_AREA ( #68270 ) ; +#61162 = ORIENTED_EDGE ( 'NONE', *, *, #73602, .F. ) ; +#61164 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69123 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20847, #99842, #52014 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61163 = FILL_AREA_STYLE ('',( #47320 ) ) ; +#61165 = VERTEX_POINT ( 'NONE', #77829 ) ; +#61166 = VECTOR ( 'NONE', #29374, 1000.000000000000000 ) ; +#61167 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#61168 = CARTESIAN_POINT ( 'NONE', ( -0.008099123004813310947, -1.050822088410799937, 0.8299999999999999600 ) ) ; +#61169 = FACE_OUTER_BOUND ( 'NONE', #24203, .T. ) ; +#61170 = FILL_AREA_STYLE_COLOUR ( '', #23639 ) ; +#61171 = VECTOR ( 'NONE', #38201, 1000.000000000000000 ) ; +#61172 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61173 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.166666666666666741, 0.000000000000000000 ) ) ; +#61174 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61175 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61176 = ADVANCED_FACE ( 'NONE', ( #14989 ), #60535, .F. ) ; +#61177 = VERTEX_POINT ( 'NONE', #76313 ) ; +#61178 = EDGE_CURVE ( 'NONE', #33336, #39098, #38530, .T. ) ; +#61179 = LINE ( 'NONE', #22861, #20013 ) ; +#61180 = PRESENTATION_STYLE_ASSIGNMENT (( #29983 ) ) ; +#61181 = STYLED_ITEM ( 'NONE', ( #39756 ), #82512 ) ; +#61182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35095 ), #56305 ) ; +#61183 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61184 = FILL_AREA_STYLE_COLOUR ( '', #89211 ) ; +#61185 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61186 = VECTOR ( 'NONE', #78427, 1000.000000000000000 ) ; +#61187 = CARTESIAN_POINT ( 'NONE', ( 1.874834857517529985, -1.237898259965849901, 0.8299999999999999600 ) ) ; +#61188 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#61189 = LINE ( 'NONE', #92287, #66104 ) ; +#61190 = LINE ( 'NONE', #13614, #4879 ) ; +#61192 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#61191 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93160 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60375, #75173, #4205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61193 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#61194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61195 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61196 = EDGE_CURVE ( 'NONE', #44266, #27194, #62037, .T. ) ; +#61197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31792 ) ) ; +#61198 = FACE_OUTER_BOUND ( 'NONE', #28163, .T. ) ; +#61199 = LINE ( 'NONE', #67313, #47640 ) ; +#61200 = VECTOR ( 'NONE', #37375, 1000.000000000000114 ) ; +#61201 = ORIENTED_EDGE ( 'NONE', *, *, #64786, .F. ) ; +#61202 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61203 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#61204 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32806 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94612, #55850, #39003 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61205 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84269 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15537, #56434, #38557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61206 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61207 = SURFACE_SIDE_STYLE ('',( #77493 ) ) ; +#61208 = FILL_AREA_STYLE_COLOUR ( '', #76515 ) ; +#61209 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30186 ) ) ; +#61210 = ADVANCED_FACE ( 'NONE', ( #85482, #32893, #47188, #64036, #56411, #87507, #95136, #218, #48228, #55886, #56904, #70160, #31366, #25747, #18032 ), #86507, .T. ) ; +#61211 = SURFACE_SIDE_STYLE ('',( #47881 ) ) ; +#61212 = VERTEX_POINT ( 'NONE', #9818 ) ; +#61213 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61214 = CIRCLE ( 'NONE', #28534, 0.2000000000000005107 ) ; +#61215 = SURFACE_STYLE_USAGE ( .BOTH. , #30017 ) ; +#61216 = PLANE ( 'NONE', #9521 ) ; +#61217 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #7336, #69688, #39077, #94678 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61218 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61219 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61220 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#61221 = ORIENTED_EDGE ( 'NONE', *, *, #67620, .F. ) ; +#61222 = ORIENTED_EDGE ( 'NONE', *, *, #79053, .F. ) ; +#61223 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41686 ) ) ; +#61224 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61225 = EDGE_LOOP ( 'NONE', ( #80411, #41660, #32774, #49203 ) ) ; +#61226 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999920064, 1.899999999999980149, 0.1829999999999920024 ) ) ; +#61227 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88985 ) ) ; +#61228 = SURFACE_SIDE_STYLE ('',( #99883 ) ) ; +#61229 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61230 = PLANE ( 'NONE', #69169 ) ; +#61231 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#61232 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #93145 ) ; +#61233 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61234 = EDGE_CURVE ( 'NONE', #98314, #23933, #93605, .T. ) ; +#61235 = SURFACE_SIDE_STYLE ('',( #45840 ) ) ; +#61236 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4142 ), #71047 ) ; +#61238 = VERTEX_POINT ( 'NONE', #16025 ) ; +#61237 = VERTEX_POINT ( 'NONE', #1226 ) ; +#61239 = ORIENTED_EDGE ( 'NONE', *, *, #30604, .F. ) ; +#61240 = STYLED_ITEM ( 'NONE', ( #80111 ), #83262 ) ; +#61241 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33547 ) ) ; +#61242 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85612, 'distance_accuracy_value', 'NONE'); +#61243 = AXIS2_PLACEMENT_3D ( 'NONE', #69244, #77968, #32536 ) ; +#61244 = SURFACE_STYLE_USAGE ( .BOTH. , #45351 ) ; +#61246 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61245 = LINE ( 'NONE', #2462, #21219 ) ; +#61247 = VERTEX_POINT ( 'NONE', #78840 ) ; +#61248 = EDGE_CURVE ( 'NONE', #13908, #63401, #8802, .T. ) ; +#61250 = ORIENTED_EDGE ( 'NONE', *, *, #8987, .T. ) ; +#61249 = AXIS2_PLACEMENT_3D ( 'NONE', #88102, #58002, #35505 ) ; +#61251 = SURFACE_STYLE_FILL_AREA ( #23959 ) ; +#61252 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48197 ) ) ; +#61253 = AXIS2_PLACEMENT_3D ( 'NONE', #32787, #31771, #1657 ) ; +#61254 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, -0.1400000000000000411 ) ) ; +#61256 = LINE ( 'NONE', #22412, #7378 ) ; +#61255 = SURFACE_STYLE_USAGE ( .BOTH. , #77539 ) ; +#61257 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#61258 = VERTEX_POINT ( 'NONE', #39038 ) ; +#61259 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86949 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57495, #44146, #96245 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61260 = STYLED_ITEM ( 'NONE', ( #90079 ), #48773 ) ; +#61261 = STYLED_ITEM ( 'NONE', ( #49031 ), #25779 ) ; +#61262 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61263 = VERTEX_POINT ( 'NONE', #32390 ) ; +#61264 = EDGE_LOOP ( 'NONE', ( #84196, #77790, #22999, #57245 ) ) ; +#61265 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61266 = AXIS2_PLACEMENT_3D ( 'NONE', #45973, #47021, #7120 ) ; +#61267 = PRESENTATION_STYLE_ASSIGNMENT (( #93335 ) ) ; +#61268 = PLANE ( 'NONE', #78403 ) ; +#61270 = ORIENTED_EDGE ( 'NONE', *, *, #99302, .T. ) ; +#61269 = SURFACE_STYLE_FILL_AREA ( #70383 ) ; +#61271 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61272 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000533, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#61273 = EDGE_LOOP ( 'NONE', ( #92724, #28449, #4829, #27067, #57959, #16799, #49853, #24458 ) ) ; +#61275 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#61274 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20311 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100000, #76623, #76130 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61276 = FILL_AREA_STYLE_COLOUR ( '', #54300 ) ; +#61277 = EDGE_LOOP ( 'NONE', ( #14175, #76737, #19979, #64453 ) ) ; +#61278 = ORIENTED_EDGE ( 'NONE', *, *, #10792, .T. ) ; +#61279 = VECTOR ( 'NONE', #60863, 1000.000000000000000 ) ; +#61280 = PRESENTATION_STYLE_ASSIGNMENT (( #37770 ) ) ; +#61281 = PLANE ( 'NONE', #98483 ) ; +#61282 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #22409, #77041, #100398, #69337 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61283 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.000000000000000000 ) ) ; +#61284 = ADVANCED_FACE ( 'NONE', ( #70672 ), #714, .F. ) ; +#61285 = STYLED_ITEM ( 'NONE', ( #71990 ), #4858 ) ; +#61286 = EDGE_CURVE ( 'NONE', #96056, #48890, #29133, .T. ) ; +#61288 = CARTESIAN_POINT ( 'NONE', ( 1.070634376467239912, -1.188596174736179956, 0.8299999999999997380 ) ) ; +#61287 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36235, #76018, #89832, #67345 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61289 = SURFACE_STYLE_FILL_AREA ( #45389 ) ; +#61290 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27185 ), #38659 ) ; +#61291 = CARTESIAN_POINT ( 'NONE', ( 0.2049220250908939944, -0.9740213618777919802, 0.8300000000000030687 ) ) ; +#61292 = ORIENTED_EDGE ( 'NONE', *, *, #99862, .F. ) ; +#61293 = ORIENTED_EDGE ( 'NONE', *, *, #84458, .F. ) ; +#61294 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79507 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75188, #75667, #37396 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61295 = SURFACE_STYLE_USAGE ( .BOTH. , #30097 ) ; +#61296 = PRESENTATION_STYLE_ASSIGNMENT (( #83750 ) ) ; +#61298 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93790 ), #44900 ) ; +#61297 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#61299 = PLANE ( 'NONE', #92345 ) ; +#61300 = SURFACE_STYLE_FILL_AREA ( #16271 ) ; +#61301 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.000000000000000000 ) ) ; +#61302 = SURFACE_STYLE_FILL_AREA ( #76577 ) ; +#61303 = EDGE_CURVE ( 'NONE', #100629, #80806, #3754, .T. ) ; +#61304 = ADVANCED_FACE ( 'NONE', ( #88518 ), #36791, .F. ) ; +#61305 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61306 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61307 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61308 = ADVANCED_FACE ( 'NONE', ( #49746 ), #26253, .F. ) ; +#61309 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61310 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8648700000000000276 ) ) ; +#61311 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98724 ) ) ; +#61312 = FILL_AREA_STYLE_COLOUR ( '', #92549 ) ; +#61313 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#61314 = EDGE_CURVE ( 'NONE', #59976, #23571, #74095, .T. ) ; +#61315 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#61316 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61317 = AXIS2_PLACEMENT_3D ( 'NONE', #92986, #61424, #89661 ) ; +#61318 = EDGE_LOOP ( 'NONE', ( #72345, #43265, #12245, #47523 ) ) ; +#61319 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76007 ) ) ; +#61320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58565, 'distance_accuracy_value', 'NONE'); +#61321 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33655, 'distance_accuracy_value', 'NONE'); +#61322 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61323 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 7.671291000000000082, 0.8648700000000000276 ) ) ; +#61324 = EDGE_CURVE ( 'NONE', #82464, #79041, #15608, .T. ) ; +#61325 = STYLED_ITEM ( 'NONE', ( #30476 ), #29235 ) ; +#61326 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20319 ), #100085 ) ; +#61327 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8648700000000000276 ) ) ; +#61328 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#61329 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558440262, -1.079220779220779969, 0.8199999999999999512 ) ) ; +#61330 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#61331 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100928 ) ; +#61332 = EDGE_CURVE ( 'NONE', #40572, #12677, #18557, .T. ) ; +#61333 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8350 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47405, #37262, #46372 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61334 = EDGE_LOOP ( 'NONE', ( #47046, #29671, #4261, #21186 ) ) ; +#61335 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.000000000000000000 ) ) ; +#61336 = EDGE_CURVE ( 'NONE', #57617, #75765, #86175, .T. ) ; +#61337 = ORIENTED_EDGE ( 'NONE', *, *, #38144, .F. ) ; +#61338 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01085786437626905764, -0.2399999999999999911 ) ) ; +#61339 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31801, 'distance_accuracy_value', 'NONE'); +#61340 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56576, 'distance_accuracy_value', 'NONE'); +#61341 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#61342 = PRESENTATION_STYLE_ASSIGNMENT (( #13772 ) ) ; +#61343 = FACE_OUTER_BOUND ( 'NONE', #92069, .T. ) ; +#61344 = FILL_AREA_STYLE ('',( #36834 ) ) ; +#61345 = SURFACE_STYLE_FILL_AREA ( #6115 ) ; +#61346 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#61347 = VECTOR ( 'NONE', #22000, 1000.000000000000000 ) ; +#61348 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#61349 = VERTEX_POINT ( 'NONE', #99951 ) ; +#61350 = SURFACE_STYLE_FILL_AREA ( #30144 ) ; +#61351 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.521936902157089967E-47, 6.141358241030730393E-32 ) ) ; +#61353 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64604 ) ) ; +#61352 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#61354 = ORIENTED_EDGE ( 'NONE', *, *, #76576, .T. ) ; +#61355 = VECTOR ( 'NONE', #31660, 1000.000000000000000 ) ; +#61356 = VERTEX_POINT ( 'NONE', #78102 ) ; +#61357 = VECTOR ( 'NONE', #31549, 1000.000000000000000 ) ; +#61358 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#61359 = PLANE ( 'NONE', #90351 ) ; +#61360 = STYLED_ITEM ( 'NONE', ( #50585 ), #13613 ) ; +#61361 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61362 = DIRECTION ( 'NONE', ( 6.123031769111889989E-17, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61364 = ADVANCED_FACE ( 'NONE', ( #45405 ), #38303, .T. ) ; +#61365 = FILL_AREA_STYLE ('',( #100010 ) ) ; +#61366 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#61368 = VERTEX_POINT ( 'NONE', #23482 ) ; +#61367 = ORIENTED_EDGE ( 'NONE', *, *, #6671, .T. ) ; +#61369 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, 0.1458578643762690752 ) ) ; +#61370 = LINE ( 'NONE', #38365, #13702 ) ; +#61371 = ORIENTED_EDGE ( 'NONE', *, *, #73745, .T. ) ; +#61372 = AXIS2_PLACEMENT_3D ( 'NONE', #96840, #51449, #66238 ) ; +#61373 = FACE_OUTER_BOUND ( 'NONE', #18478, .T. ) ; +#61375 = CARTESIAN_POINT ( 'NONE', ( -0.4757128391191070560, -0.9978229697136190568, 0.8299999999999999600 ) ) ; +#61374 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61376 = ORIENTED_EDGE ( 'NONE', *, *, #93244, .F. ) ; +#61377 = ADVANCED_FACE ( 'NONE', ( #7553 ), #37791, .T. ) ; +#61378 = ORIENTED_EDGE ( 'NONE', *, *, #20871, .F. ) ; +#61379 = FACE_OUTER_BOUND ( 'NONE', #97840, .T. ) ; +#61380 = FILL_AREA_STYLE_COLOUR ( '', #82315 ) ; +#61381 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000616, 0.8991599999999999593 ) ) ; +#61382 = ORIENTED_EDGE ( 'NONE', *, *, #59008, .T. ) ; +#61383 = ADVANCED_FACE ( 'NONE', ( #94879 ), #9812, .F. ) ; +#61385 = ORIENTED_EDGE ( 'NONE', *, *, #76047, .F. ) ; +#61384 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48333 ), #80982 ) ; +#61386 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61387 = ORIENTED_EDGE ( 'NONE', *, *, #79611, .T. ) ; +#61388 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61389 = STYLED_ITEM ( 'NONE', ( #71305 ), #30044 ) ; +#61391 = VERTEX_POINT ( 'NONE', #10821 ) ; +#61390 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61392 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61393 = STYLED_ITEM ( 'NONE', ( #64541 ), #90584 ) ; +#61394 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61395 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41770 ) ) ; +#61396 = SURFACE_STYLE_FILL_AREA ( #91984 ) ; +#61397 = EDGE_LOOP ( 'NONE', ( #22301, #85398, #10039, #80730 ) ) ; +#61398 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333316872, -2.100000000000000089, 0.000000000000000000 ) ) ; +#61399 = PLANE ( 'NONE', #47738 ) ; +#61400 = ORIENTED_EDGE ( 'NONE', *, *, #24142, .T. ) ; +#61401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61402 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36890 ), #90517 ) ; +#61404 = EDGE_LOOP ( 'NONE', ( #5405, #74805, #53534, #53488 ) ) ; +#61403 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61405 = ADVANCED_FACE ( 'NONE', ( #73213 ), #41561, .T. ) ; +#61406 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61407 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61408 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61409 = LINE ( 'NONE', #39913, #3269 ) ; +#61410 = ORIENTED_EDGE ( 'NONE', *, *, #76927, .T. ) ; +#61411 = SURFACE_STYLE_USAGE ( .BOTH. , #85354 ) ; +#61412 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#61414 = CARTESIAN_POINT ( 'NONE', ( 1.580074546203000141, -1.378252124432310044, 0.8100000000000000533 ) ) ; +#61413 = LINE ( 'NONE', #76195, #86980 ) ; +#61415 = FILL_AREA_STYLE ('',( #70037 ) ) ; +#61416 = DIRECTION ( 'NONE', ( 0.7071067811865441310, 0.000000000000000000, 0.7071067811865510144 ) ) ; +#61417 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70587 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42049, #26238, #89015 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61418 = EDGE_CURVE ( 'NONE', #29467, #36327, #65539, .T. ) ; +#61419 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19855 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11484, #43707, #28408 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61420 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#61421 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#61422 = EDGE_LOOP ( 'NONE', ( #62115, #34640, #36924, #1333 ) ) ; +#61423 = VECTOR ( 'NONE', #80303, 1000.000000000000000 ) ; +#61424 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#61425 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -1.500000000000000000, 3.495651678169978796E-76 ) ) ; +#61426 = VECTOR ( 'NONE', #92102, 1000.000000000000000 ) ; +#61427 = VERTEX_POINT ( 'NONE', #81393 ) ; +#61428 = PRESENTATION_STYLE_ASSIGNMENT (( #84859 ) ) ; +#61430 = SURFACE_STYLE_USAGE ( .BOTH. , #98601 ) ; +#61429 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#61431 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61432 = AXIS2_PLACEMENT_3D ( 'NONE', #92119, #6295, #68628 ) ; +#61433 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#61434 = ORIENTED_EDGE ( 'NONE', *, *, #57940, .F. ) ; +#61435 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999942858, -0.1400000000000000133 ) ) ; +#61436 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61437 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#61438 = SURFACE_SIDE_STYLE ('',( #13884 ) ) ; +#61439 = PLANE ( 'NONE', #17541 ) ; +#61440 = LINE ( 'NONE', #84879, #51444 ) ; +#61441 = LINE ( 'NONE', #100094, #13228 ) ; +#61442 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61443 = SURFACE_STYLE_USAGE ( .BOTH. , #30245 ) ; +#61444 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61445 = SURFACE_SIDE_STYLE ('',( #15930 ) ) ; +#61446 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51422, 'distance_accuracy_value', 'NONE'); +#61447 = FILL_AREA_STYLE ('',( #6701 ) ) ; +#61448 = ORIENTED_EDGE ( 'NONE', *, *, #70827, .T. ) ; +#61449 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 2.100000000000000089, 1.747825839084982648E-76 ) ) ; +#61450 = EDGE_CURVE ( 'NONE', #11006, #65564, #2256, .T. ) ; +#61451 = ORIENTED_EDGE ( 'NONE', *, *, #21546, .T. ) ; +#61452 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64348, 'distance_accuracy_value', 'NONE'); +#61453 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95087, 'distance_accuracy_value', 'NONE'); +#61454 = CARTESIAN_POINT ( 'NONE', ( 1.132978354350060224, -0.9623790331012080923, 0.8299999999999999600 ) ) ; +#61455 = FACE_OUTER_BOUND ( 'NONE', #46264, .T. ) ; +#61456 = FILL_AREA_STYLE ('',( #76743 ) ) ; +#61457 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.4245906043549200204, -6.018531076210109988E-33 ) ) ; +#61458 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4356 ) ) ; +#61459 = CARTESIAN_POINT ( 'NONE', ( 1.733257866282789994, -0.9021709523542820186, 0.8100000000000000533 ) ) ; +#61460 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.600000000000000089, -11.91999999999999993 ) ) ; +#61461 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#61462 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61463 = ORIENTED_EDGE ( 'NONE', *, *, #24542, .F. ) ; +#61465 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61464 = STYLED_ITEM ( 'NONE', ( #72853 ), #54904 ) ; +#61466 = FILL_AREA_STYLE ('',( #5763 ) ) ; +#61467 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13446, 'distance_accuracy_value', 'NONE'); +#61468 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10608 ) ) ; +#61469 = SURFACE_STYLE_FILL_AREA ( #85923 ) ; +#61470 = VECTOR ( 'NONE', #10297, 1000.000000000000000 ) ; +#61471 = ORIENTED_EDGE ( 'NONE', *, *, #35954, .F. ) ; +#61472 = SURFACE_STYLE_USAGE ( .BOTH. , #76755 ) ; +#61473 = FILL_AREA_STYLE ('',( #45565 ) ) ; +#61474 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8099999999999629718 ) ) ; +#61475 = FILL_AREA_STYLE ('',( #8248 ) ) ; +#61476 = SURFACE_STYLE_USAGE ( .BOTH. , #29786 ) ; +#61477 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61478 = AXIS2_PLACEMENT_3D ( 'NONE', #66174, #74346, #75338 ) ; +#61479 = EDGE_LOOP ( 'NONE', ( #2504, #27692, #33092, #37843, #81370, #27326 ) ) ; +#61480 = LINE ( 'NONE', #77778, #17954 ) ; +#61481 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34936, 'distance_accuracy_value', 'NONE'); +#61483 = VECTOR ( 'NONE', #79645, 1000.000000000000000 ) ; +#61482 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61484 = VECTOR ( 'NONE', #17096, 1000.000000000000000 ) ; +#61485 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#61486 = CLOSED_SHELL ( 'NONE', ( #83742, #33903, #90361, #65611, #3200, #166 ) ) ; +#61487 = EDGE_CURVE ( 'NONE', #15091, #61666, #49221, .T. ) ; +#61488 = ORIENTED_EDGE ( 'NONE', *, *, #35022, .F. ) ; +#61489 = VECTOR ( 'NONE', #23144, 1000.000000000000000 ) ; +#61490 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61491 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61492 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61493 = EDGE_LOOP ( 'NONE', ( #1603, #72556, #1488, #8196 ) ) ; +#61494 = VERTEX_POINT ( 'NONE', #26246 ) ; +#61495 = AXIS2_PLACEMENT_3D ( 'NONE', #90493, #82351, #58899 ) ; +#61496 = ADVANCED_FACE ( 'NONE', ( #65037 ), #34919, .T. ) ; +#61497 = VERTEX_POINT ( 'NONE', #59921 ) ; +#61499 = ORIENTED_EDGE ( 'NONE', *, *, #6195, .T. ) ; +#61498 = DIRECTION ( 'NONE', ( 0.7071067811865469066, -0.7071067811865482389, 0.000000000000000000 ) ) ; +#61501 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61500 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61502 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61503 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#61504 = ORIENTED_EDGE ( 'NONE', *, *, #63137, .F. ) ; +#61505 = ADVANCED_FACE ( 'NONE', ( #28725 ), #22074, .F. ) ; +#61506 = LINE ( 'NONE', #85457, #33661 ) ; +#61507 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.7666666666666657193, 0.000000000000000000 ) ) ; +#61508 = VERTEX_POINT ( 'NONE', #98105 ) ; +#61509 = DIRECTION ( 'NONE', ( -1.401985567973789257E-16, 1.000000000000000000, -2.620751377075717173E-32 ) ) ; +#61510 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#61511 = AXIS2_PLACEMENT_3D ( 'NONE', #93791, #1432, #48911 ) ; +#61512 = EDGE_LOOP ( 'NONE', ( #72460, #3857, #98676, #17376 ) ) ; +#61514 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#61513 = PRESENTATION_STYLE_ASSIGNMENT (( #30312 ) ) ; +#61515 = EDGE_LOOP ( 'NONE', ( #58885, #18585, #71247, #175, #41264, #99208 ) ) ; +#61516 = EDGE_CURVE ( 'NONE', #85184, #76681, #67034, .T. ) ; +#61517 = ADVANCED_FACE ( 'NONE', ( #60907 ), #74713, .T. ) ; +#61519 = PRESENTATION_STYLE_ASSIGNMENT (( #31346 ) ) ; +#61518 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61520 = AXIS2_PLACEMENT_3D ( 'NONE', #69391, #29611, #53617 ) ; +#61521 = FILL_AREA_STYLE_COLOUR ( '', #57223 ) ; +#61522 = DIRECTION ( 'NONE', ( -1.000000000000000000, 6.842277657835989739E-47, 1.355252715606876105E-16 ) ) ; +#61523 = EDGE_CURVE ( 'NONE', #1971, #14292, #93986, .T. ) ; +#61524 = ADVANCED_FACE ( 'NONE', ( #78230 ), #16389, .T. ) ; +#61525 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12518 ), #100503 ) ; +#61526 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61527 = ORIENTED_EDGE ( 'NONE', *, *, #94451, .T. ) ; +#61528 = FACE_OUTER_BOUND ( 'NONE', #67476, .T. ) ; +#61529 = ORIENTED_EDGE ( 'NONE', *, *, #51697, .T. ) ; +#61530 = FILL_AREA_STYLE_COLOUR ( '', #100761 ) ; +#61532 = SURFACE_STYLE_FILL_AREA ( #28846 ) ; +#61531 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61533 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61534 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61535 = EDGE_CURVE ( 'NONE', #38423, #93302, #14871, .T. ) ; +#61536 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89319, 'distance_accuracy_value', 'NONE'); +#61537 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#61538 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4849999999999999867, -0.2400000000000000189 ) ) ; +#61539 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.8999999999999990230, 0.1829999999999829818 ) ) ; +#61540 = SURFACE_SIDE_STYLE ('',( #45638 ) ) ; +#61541 = PRESENTATION_STYLE_ASSIGNMENT (( #30332 ) ) ; +#61542 = EDGE_CURVE ( 'NONE', #14292, #48328, #71062, .T. ) ; +#61543 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61544 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61545 = ORIENTED_EDGE ( 'NONE', *, *, #18662, .F. ) ; +#61546 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61547 = STYLED_ITEM ( 'NONE', ( #78864 ), #24039 ) ; +#61548 = VECTOR ( 'NONE', #35331, 1000.000000000000000 ) ; +#61549 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#61550 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#61551 = LINE ( 'NONE', #45158, #37097 ) ; +#61552 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#61553 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59892 ), #35473 ) ; +#61554 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#61555 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61556 = LINE ( 'NONE', #15004, #40449 ) ; +#61557 = CLOSED_SHELL ( 'NONE', ( #24439, #59769, #80088, #47832, #77749, #33371 ) ) ; +#61558 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61559 = ORIENTED_EDGE ( 'NONE', *, *, #34952, .F. ) ; +#61560 = PRESENTATION_STYLE_ASSIGNMENT (( #60064 ) ) ; +#61561 = AXIS2_PLACEMENT_3D ( 'NONE', #33325, #18474, #18980 ) ; +#61562 = SURFACE_SIDE_STYLE ('',( #38055 ) ) ; +#61563 = CARTESIAN_POINT ( 'NONE', ( -0.007147714975284390031, -1.399205570841099977, 0.8100000000000000533 ) ) ; +#61564 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3139, 'distance_accuracy_value', 'NONE'); +#61565 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61566 = SURFACE_STYLE_USAGE ( .BOTH. , #15016 ) ; +#61567 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61568 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61569 = VECTOR ( 'NONE', #98451, 1000.000000000000000 ) ; +#61570 = PRESENTATION_STYLE_ASSIGNMENT (( #75353 ) ) ; +#61571 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61572 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#61573 = ADVANCED_FACE ( 'NONE', ( #62413 ), #86893, .F. ) ; +#61574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9145, 'distance_accuracy_value', 'NONE'); +#61575 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#61576 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61577 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83942, 'distance_accuracy_value', 'NONE'); +#61578 = PLANE ( 'NONE', #56950 ) ; +#61579 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#61580 = EDGE_CURVE ( 'NONE', #8318, #4845, #23594, .T. ) ; +#61581 = CARTESIAN_POINT ( 'NONE', ( -1.268301777710219902, -1.110638925478639960, 0.8299999999999999600 ) ) ; +#61582 = ORIENTED_EDGE ( 'NONE', *, *, #96411, .T. ) ; +#61583 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#61584 = SURFACE_STYLE_FILL_AREA ( #29411 ) ; +#61585 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44946, 'distance_accuracy_value', 'NONE'); +#61586 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61587 = AXIS2_PLACEMENT_3D ( 'NONE', #3684, #56351, #63973 ) ; +#61588 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#61589 = STYLED_ITEM ( 'NONE', ( #345 ), #74097 ) ; +#61590 = ORIENTED_EDGE ( 'NONE', *, *, #61971, .F. ) ; +#61591 = PRESENTATION_STYLE_ASSIGNMENT (( #15042 ) ) ; +#61592 = LINE ( 'NONE', #78397, #28276 ) ; +#61593 = CARTESIAN_POINT ( 'NONE', ( 0.6431619866146595088, 0.5992840759270875450, 0.8299999999999999600 ) ) ; +#61594 = VECTOR ( 'NONE', #22856, 1000.000000000000000 ) ; +#61595 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#61596 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61597 = ORIENTED_EDGE ( 'NONE', *, *, #67217, .T. ) ; +#61598 = PRESENTATION_STYLE_ASSIGNMENT (( #77375 ) ) ; +#61599 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8648700000000000276 ) ) ; +#61600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59542, 'distance_accuracy_value', 'NONE'); +#61601 = VECTOR ( 'NONE', #60211, 1000.000000000000000 ) ; +#61602 = PRESENTATION_STYLE_ASSIGNMENT (( #17350 ) ) ; +#61603 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61604 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95727 ), #43631 ) ; +#61605 = VERTEX_POINT ( 'NONE', #22583 ) ; +#61606 = ORIENTED_EDGE ( 'NONE', *, *, #62605, .F. ) ; +#61607 = PLANE ( 'NONE', #9600 ) ; +#61608 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999996181, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#61609 = VERTEX_POINT ( 'NONE', #92982 ) ; +#61610 = PRESENTATION_STYLE_ASSIGNMENT (( #54448 ) ) ; +#61611 = VECTOR ( 'NONE', #40175, 1000.000000000000000 ) ; +#61612 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#61613 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61614 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46843 ) ) ; +#61615 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #53399, #1202 ) ; +#61616 = EDGE_LOOP ( 'NONE', ( #87575, #18002, #67708, #62997, #73537, #59210 ) ) ; +#61617 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77911 ) ) ; +#61618 = ORIENTED_EDGE ( 'NONE', *, *, #53130, .T. ) ; +#61619 = PRESENTATION_STYLE_ASSIGNMENT (( #53941 ) ) ; +#61620 = STYLED_ITEM ( 'NONE', ( #22618 ), #41393 ) ; +#61621 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61622 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55069 ) ) ; +#61624 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#61623 = SURFACE_SIDE_STYLE ('',( #39118 ) ) ; +#61625 = SURFACE_STYLE_USAGE ( .BOTH. , #69737 ) ; +#61626 = CLOSED_SHELL ( 'NONE', ( #64413, #90278, #62512, #22113, #11028, #13398 ) ) ; +#61627 = ORIENTED_EDGE ( 'NONE', *, *, #72693, .T. ) ; +#61629 = VECTOR ( 'NONE', #70429, 1000.000000000000000 ) ; +#61628 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#61630 = VECTOR ( 'NONE', #27561, 1000.000000000000000 ) ; +#61631 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61632 = ORIENTED_EDGE ( 'NONE', *, *, #22644, .T. ) ; +#61634 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61633 = SURFACE_STYLE_USAGE ( .BOTH. , #6886 ) ; +#61635 = ORIENTED_EDGE ( 'NONE', *, *, #18369, .F. ) ; +#61636 = ORIENTED_EDGE ( 'NONE', *, *, #12504, .T. ) ; +#61637 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61638 = STYLED_ITEM ( 'NONE', ( #43784 ), #14873 ) ; +#61640 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61639 = LINE ( 'NONE', #63146, #98294 ) ; +#61641 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80936 ) ) ; +#61642 = FILL_AREA_STYLE ('',( #100289 ) ) ; +#61644 = ORIENTED_EDGE ( 'NONE', *, *, #14906, .T. ) ; +#61643 = FILL_AREA_STYLE_COLOUR ( '', #36283 ) ; +#61645 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30609 ), #17578 ) ; +#61646 = SURFACE_STYLE_FILL_AREA ( #6896 ) ; +#61647 = EDGE_CURVE ( 'NONE', #38419, #80230, #74426, .T. ) ; +#61648 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#61649 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61650 = VERTEX_POINT ( 'NONE', #2634 ) ; +#61652 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61651 = FILL_AREA_STYLE ('',( #76945 ) ) ; +#61653 = VERTEX_POINT ( 'NONE', #56278 ) ; +#61654 = ORIENTED_EDGE ( 'NONE', *, *, #76929, .T. ) ; +#61655 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84496 ) ) ; +#61657 = SURFACE_SIDE_STYLE ('',( #85101 ) ) ; +#61656 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#61658 = CARTESIAN_POINT ( 'NONE', ( -0.1500000000000000222, 0.1499999999999999667, -0.01999999999999999695 ) ) ; +#61659 = FILL_AREA_STYLE_COLOUR ( '', #74264 ) ; +#61660 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61661 = AXIS2_PLACEMENT_3D ( 'NONE', #67527, #43555, #98603 ) ; +#61662 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61663 = EDGE_CURVE ( 'NONE', #54246, #38282, #80761, .T. ) ; +#61664 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61665 = VERTEX_POINT ( 'NONE', #81277 ) ; +#61666 = VERTEX_POINT ( 'NONE', #9699 ) ; +#61667 = CARTESIAN_POINT ( 'NONE', ( 13.17837700000000112, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#61668 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#61669 = STYLED_ITEM ( 'NONE', ( #77157 ), #56445 ) ; +#61670 = LINE ( 'NONE', #92746, #33750 ) ; +#61671 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61672 = FILL_AREA_STYLE_COLOUR ( '', #7790 ) ; +#61673 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61674 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#61676 = ORIENTED_EDGE ( 'NONE', *, *, #59104, .T. ) ; +#61675 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61677 = FILL_AREA_STYLE ('',( #31006 ) ) ; +#61678 = SURFACE_STYLE_USAGE ( .BOTH. , #21844 ) ; +#61679 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.01499999999999999944, 0.1400000000000000133 ) ) ; +#61680 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76751 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59555, #32886, #54877 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61681 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11291, 'distance_accuracy_value', 'NONE'); +#61682 = SURFACE_STYLE_FILL_AREA ( #53508 ) ; +#61683 = SURFACE_STYLE_USAGE ( .BOTH. , #83651 ) ; +#61684 = CARTESIAN_POINT ( 'NONE', ( 9.514457499499824777, 4.008477499499824681, 0.8991599999999999593 ) ) ; +#61685 = ADVANCED_FACE ( 'NONE', ( #11201 ), #96530, .T. ) ; +#61686 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -1.166666666666666741, 0.000000000000000000 ) ) ; +#61687 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#61688 = FILL_AREA_STYLE ('',( #30482 ) ) ; +#61689 = SURFACE_SIDE_STYLE ('',( #7953 ) ) ; +#61690 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28652 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57829, #34838, #79022 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61691 = SURFACE_STYLE_FILL_AREA ( #98872 ) ; +#61692 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61693 = CLOSED_SHELL ( 'NONE', ( #66259, #3179, #88558, #8801, #98201, #42554 ) ) ; +#61695 = EDGE_CURVE ( 'NONE', #86528, #82928, #87383, .T. ) ; +#61694 = SURFACE_SIDE_STYLE ('',( #55043 ) ) ; +#61696 = CARTESIAN_POINT ( 'NONE', ( -1.088394230359242876, -0.8857285283026523626, 0.8100000000000723288 ) ) ; +#61697 = VERTEX_POINT ( 'NONE', #26636 ) ; +#61698 = DIRECTION ( 'NONE', ( 0.4475798637663839785, -0.8942439631056310345, 0.000000000000000000 ) ) ; +#61699 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#61700 = CARTESIAN_POINT ( 'NONE', ( 1.592240980523089933, -1.399421068953929925, 0.8299999999999977396 ) ) ; +#61701 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66690, #43214, #74373, #59082, #4401, #81048, #82541, #12491, #98270, #10982, #28407, #59597, #80538, #10455, #41728, #42234, #99264, #37087, #44209 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.101913602857871397E-05, 4.134561820478297665E-05, 6.078410685937110300E-05, 7.975871741957252464E-05, 9.809563397106762063E-05, 0.0001159246450513708756, 0.0001331015568629862768, 0.0001500848695792009722, 0.0001669813285112673081, 0.0001841742391617554790, 0.0002016734443718590307, 0.0002197766717633888706, 0.0002385148391632708814, 0.0002581511027027656464, 0.0002785647693864929091, 0.0003002811567888427125 ), + .UNSPECIFIED. ) ; +#61702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17792, 'distance_accuracy_value', 'NONE'); +#61703 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#61704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100679 ) ) ; +#61705 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.009999999999999998473, 1.129999999999999893 ) ) ; +#61706 = CARTESIAN_POINT ( 'NONE', ( 1.149382776344263224, -1.140583172347456875, 0.8099999999999014655 ) ) ; +#61707 = AXIS2_PLACEMENT_3D ( 'NONE', #38193, #100346, #53018 ) ; +#61708 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8199999999999999512 ) ) ; +#61709 = AXIS2_PLACEMENT_3D ( 'NONE', #29955, #3618, #51107 ) ; +#61710 = EDGE_LOOP ( 'NONE', ( #95938, #80972, #41307, #33511 ) ) ; +#61711 = SURFACE_SIDE_STYLE ('',( #16195 ) ) ; +#61712 = LINE ( 'NONE', #6492, #36690 ) ; +#61713 = VECTOR ( 'NONE', #99614, 1000.000000000000114 ) ; +#61714 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61715 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81976, 'distance_accuracy_value', 'NONE'); +#61716 = PRESENTATION_STYLE_ASSIGNMENT (( #30506 ) ) ; +#61717 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36120, 'distance_accuracy_value', 'NONE'); +#61718 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61719 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61720 = EDGE_CURVE ( 'NONE', #29371, #47331, #33282, .T. ) ; +#61721 = ORIENTED_EDGE ( 'NONE', *, *, #5170, .T. ) ; +#61722 = ORIENTED_EDGE ( 'NONE', *, *, #93435, .T. ) ; +#61723 = DIRECTION ( 'NONE', ( 0.7071067811865455743, 0.7071067811865495711, 0.000000000000000000 ) ) ; +#61724 = LINE ( 'NONE', #22914, #50405 ) ; +#61725 = VECTOR ( 'NONE', #67797, 1000.000000000000000 ) ; +#61726 = ORIENTED_EDGE ( 'NONE', *, *, #98861, .T. ) ; +#61727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20745 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25102, #63403, #33752 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61728 = EDGE_CURVE ( 'NONE', #55200, #4099, #18940, .T. ) ; +#61729 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #69555, #30751, #54801, #39435 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61730 = FILL_AREA_STYLE_COLOUR ( '', #69113 ) ; +#61731 = SHAPE_DEFINITION_REPRESENTATION ( #84112, #39722 ) ; +#61732 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61733 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#61735 = ORIENTED_EDGE ( 'NONE', *, *, #94325, .F. ) ; +#61734 = VERTEX_POINT ( 'NONE', #17420 ) ; +#61736 = ORIENTED_EDGE ( 'NONE', *, *, #82764, .T. ) ; +#61737 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#61738 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76423 ) ) ; +#61739 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72147, #57877, #72640, #49174 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61741 = FILL_AREA_STYLE_COLOUR ( '', #47934 ) ; +#61740 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#61742 = VERTEX_POINT ( 'NONE', #34807 ) ; +#61743 = EDGE_CURVE ( 'NONE', #4927, #53318, #26134, .T. ) ; +#61744 = AXIS2_PLACEMENT_3D ( 'NONE', #100840, #19219, #2422 ) ; +#61745 = ORIENTED_EDGE ( 'NONE', *, *, #2159, .F. ) ; +#61746 = ADVANCED_FACE ( 'NONE', ( #65932 ), #48615, .T. ) ; +#61747 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#61748 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#61749 = STYLED_ITEM ( 'NONE', ( #6676 ), #79765 ) ; +#61751 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61750 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#61752 = FILL_AREA_STYLE ('',( #30540 ) ) ; +#61753 = VERTEX_POINT ( 'NONE', #91896 ) ; +#61754 = FACE_OUTER_BOUND ( 'NONE', #87975, .T. ) ; +#61755 = VERTEX_POINT ( 'NONE', #82753 ) ; +#61756 = ORIENTED_EDGE ( 'NONE', *, *, #11209, .F. ) ; +#61757 = CARTESIAN_POINT ( 'NONE', ( 0.2638348760318000030, -1.377348110544800219, 0.8300000000000004041 ) ) ; +#61758 = VECTOR ( 'NONE', #47436, 1000.000000000000000 ) ; +#61759 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58577 ) ) ; +#61760 = SURFACE_STYLE_FILL_AREA ( #46894 ) ; +#61761 = VECTOR ( 'NONE', #22619, 1000.000000000000000 ) ; +#61762 = FILL_AREA_STYLE ('',( #16237 ) ) ; +#61763 = LINE ( 'NONE', #22946, #91291 ) ; +#61764 = ORIENTED_EDGE ( 'NONE', *, *, #48814, .T. ) ; +#61765 = STYLED_ITEM ( 'NONE', ( #59089 ), #41954 ) ; +#61766 = ADVANCED_FACE ( 'NONE', ( #83754 ), #12726, .F. ) ; +#61767 = SURFACE_STYLE_FILL_AREA ( #45376 ) ; +#61768 = VERTEX_POINT ( 'NONE', #98967 ) ; +#61769 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61770 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61771 = ORIENTED_EDGE ( 'NONE', *, *, #54057, .T. ) ; +#61772 = ORIENTED_EDGE ( 'NONE', *, *, #24625, .T. ) ; +#61773 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61774 = PRESENTATION_STYLE_ASSIGNMENT (( #100908 ) ) ; +#61775 = CARTESIAN_POINT ( 'NONE', ( -0.5282008442508040469, -1.258308808185959915, 0.8299999999999999600 ) ) ; +#61776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4674 ) ) ; +#61777 = LINE ( 'NONE', #99933, #33133 ) ; +#61779 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61778 = STYLED_ITEM ( 'NONE', ( #48888 ), #15099 ) ; +#61780 = CARTESIAN_POINT ( 'NONE', ( 1.207735270546159922, -1.226800916006800080, 0.8299999999999997380 ) ) ; +#61781 = EDGE_CURVE ( 'NONE', #8413, #41478, #82262, .T. ) ; +#61782 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.000000000000000000 ) ) ; +#61783 = LINE ( 'NONE', #92846, #39317 ) ; +#61784 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79720 ), #94312 ) ; +#61785 = VERTEX_POINT ( 'NONE', #29612 ) ; +#61786 = CARTESIAN_POINT ( 'NONE', ( 0.4190707317248760222, -1.180616848856389955, 0.8100000000000000533 ) ) ; +#61787 = ORIENTED_EDGE ( 'NONE', *, *, #8316, .F. ) ; +#61788 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#61789 = CARTESIAN_POINT ( 'NONE', ( -0.5325711222945195278, -0.9709989571038968315, 0.8299999999999999600 ) ) ; +#61791 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78536, 'distance_accuracy_value', 'NONE'); +#61790 = PLANE ( 'NONE', #89199 ) ; +#61792 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61794 = SURFACE_STYLE_USAGE ( .BOTH. , #39274 ) ; +#61793 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#61795 = CARTESIAN_POINT ( 'NONE', ( 1.788364155591040117, -1.009819306370540071, 0.8100000000000000533 ) ) ; +#61796 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#61797 = SURFACE_STYLE_USAGE ( .BOTH. , #77087 ) ; +#61798 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61799 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#61800 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61801 = ADVANCED_FACE ( 'NONE', ( #43435 ), #74599, .T. ) ; +#61802 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61803 = EDGE_CURVE ( 'NONE', #76014, #34880, #48298, .T. ) ; +#61804 = FILL_AREA_STYLE_COLOUR ( '', #50497 ) ; +#61806 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.149999999999970157, 0.000000000000000000 ) ) ; +#61805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61807 = LINE ( 'NONE', #92877, #65850 ) ; +#61808 = VECTOR ( 'NONE', #70642, 1000.000000000000000 ) ; +#61809 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95313 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13782, #46465, #83310 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61810 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32507 ), #47133 ) ; +#61811 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34244, 'distance_accuracy_value', 'NONE'); +#61812 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #96212, #97692, #26313, #3808 ), + ( #90076, #57465, #97216, #72251 ), + ( #80430, #88569, #12895, #51800 ), + ( #75763, #74772, #67580, #45571 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 0.8047378541243648264, 0.6476030138606878594, 0.6476030138606878594, 0.8047378541243648264), + ( 1.000000000000000000, 0.8047378541243652705, 0.8047378541243652705, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#61813 = ORIENTED_EDGE ( 'NONE', *, *, #37757, .F. ) ; +#61815 = ADVANCED_FACE ( 'NONE', ( #89896 ), #62291, .T. ) ; +#61814 = FILL_AREA_STYLE_COLOUR ( '', #50525 ) ; +#61816 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61817 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#61818 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -2.100000000000000089, 1.046837090475817223E-78 ) ) ; +#61819 = SURFACE_SIDE_STYLE ('',( #25914 ) ) ; +#61820 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#61821 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7228 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34182, #25017, #18811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61822 = SURFACE_STYLE_USAGE ( .BOTH. , #99981 ) ; +#61823 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#61824 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61825 = AXIS2_PLACEMENT_3D ( 'NONE', #96889, #26992, #73453 ) ; +#61826 = VECTOR ( 'NONE', #63727, 1000.000000000000000 ) ; +#61827 = ORIENTED_EDGE ( 'NONE', *, *, #64106, .F. ) ; +#61828 = FILL_AREA_STYLE ('',( #23015 ) ) ; +#61829 = VERTEX_POINT ( 'NONE', #480 ) ; +#61830 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48800 ), #83031 ) ; +#61831 = FILL_AREA_STYLE_COLOUR ( '', #76398 ) ; +#61832 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.276179938779915091, -0.02000000000000000042 ) ) ; +#61833 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99002 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58482, #12889, #4308 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61834 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61835 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61836 = PRESENTATION_STYLE_ASSIGNMENT (( #78631 ) ) ; +#61837 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#61838 = VERTEX_POINT ( 'NONE', #38300 ) ; +#61839 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000622, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#61840 = SURFACE_SIDE_STYLE ('',( #22502 ) ) ; +#61841 = ORIENTED_EDGE ( 'NONE', *, *, #65254, .F. ) ; +#61842 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#61843 = FILL_AREA_STYLE ('',( #39327 ) ) ; +#61844 = ORIENTED_EDGE ( 'NONE', *, *, #36056, .F. ) ; +#61845 = ADVANCED_FACE ( 'NONE', ( #15782 ), #87868, .T. ) ; +#61846 = CARTESIAN_POINT ( 'NONE', ( 1.130331698131229912, -1.432449005990829916, 0.8299999999999999600 ) ) ; +#61847 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61848 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4849999999999999867, 0.2400000000000000189 ) ) ; +#61849 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61850 = PLANE ( 'NONE', #32656 ) ; +#61852 = ORIENTED_EDGE ( 'NONE', *, *, #22508, .F. ) ; +#61851 = VERTEX_POINT ( 'NONE', #92388 ) ; +#61853 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61854 = LINE ( 'NONE', #31198, #16957 ) ; +#61855 = ORIENTED_EDGE ( 'NONE', *, *, #13579, .F. ) ; +#61856 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#61858 = CARTESIAN_POINT ( 'NONE', ( -0.4682654858281209975, -1.005282756156510082, 0.8100000000000000533 ) ) ; +#61857 = CARTESIAN_POINT ( 'NONE', ( 3.233333333333330284, 3.500000000000000000, 0.000000000000000000 ) ) ; +#61859 = EDGE_LOOP ( 'NONE', ( #51355, #18982, #69840, #78400 ) ) ; +#61860 = ADVANCED_FACE ( 'NONE', ( #22984 ), #70415, .T. ) ; +#61861 = VERTEX_POINT ( 'NONE', #47962 ) ; +#61862 = ADVANCED_FACE ( 'NONE', ( #64787 ), #80641, .F. ) ; +#61863 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#61864 = FILL_AREA_STYLE_COLOUR ( '', #33298 ) ; +#61865 = VECTOR ( 'NONE', #52780, 1000.000000000000000 ) ; +#61866 = VECTOR ( 'NONE', #7280, 1000.000000000000000 ) ; +#61868 = SURFACE_SIDE_STYLE ('',( #2097 ) ) ; +#61867 = SURFACE_STYLE_USAGE ( .BOTH. , #86334 ) ; +#61869 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61870 = ORIENTED_EDGE ( 'NONE', *, *, #87309, .T. ) ; +#61871 = EDGE_CURVE ( 'NONE', #25531, #96537, #1511, .T. ) ; +#61872 = ORIENTED_EDGE ( 'NONE', *, *, #89983, .F. ) ; +#61873 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 6.822762999999999245, 0.8991599999999999593 ) ) ; +#61874 = VERTEX_POINT ( 'NONE', #50009 ) ; +#61875 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61876 = STYLED_ITEM ( 'NONE', ( #95106 ), #92932 ) ; +#61877 = AXIS2_PLACEMENT_3D ( 'NONE', #39572, #70705, #47733 ) ; +#61878 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92852 ) ) ; +#61880 = VERTEX_POINT ( 'NONE', #71958 ) ; +#61879 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#61881 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61882 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.276179938779915091, 0.000000000000000000 ) ) ; +#61883 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8991599999999999593 ) ) ; +#61884 = VERTEX_POINT ( 'NONE', #72959 ) ; +#61885 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61886 = ORIENTED_EDGE ( 'NONE', *, *, #50113, .T. ) ; +#61887 = AXIS2_PLACEMENT_3D ( 'NONE', #18100, #49298, #41139 ) ; +#61888 = ADVANCED_FACE ( 'NONE', ( #3012 ), #88780, .T. ) ; +#61889 = FILL_AREA_STYLE ('',( #5187 ) ) ; +#61890 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#61891 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41970, #81298, #72101, #87909 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61893 = ORIENTED_EDGE ( 'NONE', *, *, #12257, .F. ) ; +#61892 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61894 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#61895 = ADVANCED_FACE ( 'NONE', ( #11080 ), #63804, .T. ) ; +#61896 = LINE ( 'NONE', #93973, #93849 ) ; +#61897 = CARTESIAN_POINT ( 'NONE', ( -0.9970074157821667837, -1.197864191688262192, 0.8099999999998419575 ) ) ; +#61898 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#61899 = VECTOR ( 'NONE', #39527, 1000.000000000000000 ) ; +#61900 = EDGE_CURVE ( 'NONE', #98821, #67869, #52006, .T. ) ; +#61901 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11213 ) ) ; +#61902 = FILL_AREA_STYLE_COLOUR ( '', #72358 ) ; +#61903 = ORIENTED_EDGE ( 'NONE', *, *, #48932, .T. ) ; +#61904 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#61905 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70031 ) ) ; +#61906 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333330195, 1.300000000000000266, 1.747825839084982648E-76 ) ) ; +#61907 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61909 = CARTESIAN_POINT ( 'NONE', ( 1.628132030843780331, -1.431361989143759894, 0.8299999999999999600 ) ) ; +#61908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61910 = SURFACE_STYLE_USAGE ( .BOTH. , #30718 ) ; +#61911 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #94762 ) ) ; +#61912 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#61913 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61914 = VECTOR ( 'NONE', #29143, 1000.000000000000000 ) ; +#61915 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, 0.000000000000000000 ) ) ; +#61916 = ORIENTED_EDGE ( 'NONE', *, *, #79006, .F. ) ; +#61917 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61918 = STYLED_ITEM ( 'NONE', ( #73123 ), #15602 ) ; +#61919 = VERTEX_POINT ( 'NONE', #75460 ) ; +#61920 = EDGE_CURVE ( 'NONE', #7996, #12027, #5467, .T. ) ; +#61922 = FACE_OUTER_BOUND ( 'NONE', #24980, .T. ) ; +#61921 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#61923 = SURFACE_SIDE_STYLE ('',( #30735 ) ) ; +#61924 = VECTOR ( 'NONE', #81577, 1000.000000000000000 ) ; +#61925 = CARTESIAN_POINT ( 'NONE', ( -0.7996373468737240087, 0.5991788043593869739, 0.8299999999999999600 ) ) ; +#61926 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#61927 = VERTEX_POINT ( 'NONE', #36685 ) ; +#61928 = CARTESIAN_POINT ( 'NONE', ( 1.662784294148539344, -1.164927051866627261, 0.8099999999999999423 ) ) ; +#61929 = EDGE_CURVE ( 'NONE', #2862, #79398, #43482, .T. ) ; +#61930 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8099999999999815126 ) ) ; +#61931 = SURFACE_STYLE_FILL_AREA ( #69027 ) ; +#61932 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61933 = SURFACE_STYLE_USAGE ( .BOTH. , #40973 ) ; +#61934 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#61935 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#61936 = FACE_OUTER_BOUND ( 'NONE', #17251, .T. ) ; +#61937 = VECTOR ( 'NONE', #49153, 1000.000000000000000 ) ; +#61938 = FACE_OUTER_BOUND ( 'NONE', #95510, .T. ) ; +#61939 = EDGE_CURVE ( 'NONE', #1743, #75149, #28995, .T. ) ; +#61940 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#61941 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#61942 = SURFACE_STYLE_USAGE ( .BOTH. , #60940 ) ; +#61943 = VECTOR ( 'NONE', #32116, 1000.000000000000114 ) ; +#61944 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61945 = LINE ( 'NONE', #22110, #94364 ) ; +#61946 = ORIENTED_EDGE ( 'NONE', *, *, #89632, .T. ) ; +#61947 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61948 = EDGE_CURVE ( 'NONE', #43003, #60664, #58179, .T. ) ; +#61949 = EDGE_LOOP ( 'NONE', ( #46280, #22543, #57313, #25340 ) ) ; +#61950 = FACE_OUTER_BOUND ( 'NONE', #52461, .T. ) ; +#61951 = STYLED_ITEM ( 'NONE', ( #29704 ), #57327 ) ; +#61952 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#61953 = VECTOR ( 'NONE', #29310, 1000.000000000000000 ) ; +#61955 = SURFACE_STYLE_USAGE ( .BOTH. , #30255 ) ; +#61954 = AXIS2_PLACEMENT_3D ( 'NONE', #95947, #49528, #27560 ) ; +#61956 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61957 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4843 ), #26103 ) ; +#61958 = CARTESIAN_POINT ( 'NONE', ( 0.003128152952664109854, -1.177156496261070107, 0.8100000000000000533 ) ) ; +#61959 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.000000000000000000 ) ) ; +#61960 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61961 = ORIENTED_EDGE ( 'NONE', *, *, #15112, .F. ) ; +#61962 = PLANE ( 'NONE', #84059 ) ; +#61963 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#61964 = CIRCLE ( 'NONE', #47211, 0.1000000000000000472 ) ; +#61965 = FILL_AREA_STYLE_COLOUR ( '', #88411 ) ; +#61966 = ORIENTED_EDGE ( 'NONE', *, *, #25555, .F. ) ; +#61967 = FACE_OUTER_BOUND ( 'NONE', #55509, .T. ) ; +#61969 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61968 = VECTOR ( 'NONE', #56291, 1000.000000000000000 ) ; +#61970 = EDGE_LOOP ( 'NONE', ( #10884, #40344, #666, #22036 ) ) ; +#61971 = EDGE_CURVE ( 'NONE', #21167, #31068, #21335, .T. ) ; +#61972 = EDGE_CURVE ( 'NONE', #56713, #67465, #58675, .T. ) ; +#61973 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#61974 = FACE_OUTER_BOUND ( 'NONE', #67725, .T. ) ; +#61975 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#61976 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#61977 = AXIS2_PLACEMENT_3D ( 'NONE', #16162, #41710, #87157 ) ; +#61978 = ORIENTED_EDGE ( 'NONE', *, *, #96027, .T. ) ; +#61979 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66832 ), #75018 ) ; +#61980 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63594 ) ) ; +#61981 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#61982 = SURFACE_STYLE_USAGE ( .BOTH. , #84924 ) ; +#61983 = EDGE_LOOP ( 'NONE', ( #65981, #46068, #2260, #97817 ) ) ; +#61984 = EDGE_CURVE ( 'NONE', #57773, #92605, #37184, .T. ) ; +#61985 = STYLED_ITEM ( 'NONE', ( #49060 ), #10633 ) ; +#61986 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#61987 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61988 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#61989 = SURFACE_STYLE_USAGE ( .BOTH. , #30805 ) ; +#61990 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#61991 = SURFACE_STYLE_FILL_AREA ( #14946 ) ; +#61992 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01500000000000000118, 0.2500000000000000000 ) ) ; +#61993 = ORIENTED_EDGE ( 'NONE', *, *, #40256, .F. ) ; +#61994 = EDGE_CURVE ( 'NONE', #57973, #98563, #28023, .T. ) ; +#61995 = ORIENTED_EDGE ( 'NONE', *, *, #18836, .F. ) ; +#61996 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86371, #22568, #46007, #30708 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#61997 = ORIENTED_EDGE ( 'NONE', *, *, #45039, .F. ) ; +#61998 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80680 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40620, #10880, #56471 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#61999 = VERTEX_POINT ( 'NONE', #42821 ) ; +#62000 = VERTEX_POINT ( 'NONE', #4013 ) ; +#62001 = FILL_AREA_STYLE_COLOUR ( '', #75216 ) ; +#62002 = SURFACE_STYLE_USAGE ( .BOTH. , #23688 ) ; +#62003 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8648700000000000276 ) ) ; +#62004 = PRESENTATION_STYLE_ASSIGNMENT (( #100157 ) ) ; +#62005 = VERTEX_POINT ( 'NONE', #35189 ) ; +#62006 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#62007 = ORIENTED_EDGE ( 'NONE', *, *, #7783, .F. ) ; +#62008 = CARTESIAN_POINT ( 'NONE', ( 1.420458916718859932, -1.419416888468929994, 0.8100000000000000533 ) ) ; +#62009 = EDGE_CURVE ( 'NONE', #68837, #10390, #66307, .T. ) ; +#62010 = SURFACE_STYLE_USAGE ( .BOTH. , #39011 ) ; +#62011 = SURFACE_STYLE_USAGE ( .BOTH. , #45608 ) ; +#62012 = ORIENTED_EDGE ( 'NONE', *, *, #51620, .F. ) ; +#62014 = CARTESIAN_POINT ( 'NONE', ( 6.367831750250086742, 10.54921475025008881, 0.8648700000000000276 ) ) ; +#62013 = SURFACE_SIDE_STYLE ('',( #29343 ) ) ; +#62015 = ORIENTED_EDGE ( 'NONE', *, *, #5871, .F. ) ; +#62016 = STYLED_ITEM ( 'NONE', ( #43153 ), #86227 ) ; +#62017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97798 ), #4903 ) ; +#62018 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62020 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62019 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#62021 = LINE ( 'NONE', #13443, #97871 ) ; +#62023 = EDGE_CURVE ( 'NONE', #55713, #38519, #97405, .T. ) ; +#62022 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.7099999999999999645, 0.8000000000000001554 ) ) ; +#62024 = VECTOR ( 'NONE', #72933, 1000.000000000000000 ) ; +#62025 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#62026 = VECTOR ( 'NONE', #92563, 1000.000000000000000 ) ; +#62027 = STYLED_ITEM ( 'NONE', ( #62281 ), #94309 ) ; +#62028 = EDGE_LOOP ( 'NONE', ( #67377, #52321, #18515, #60389 ) ) ; +#62029 = ORIENTED_EDGE ( 'NONE', *, *, #90677, .F. ) ; +#62031 = FILL_AREA_STYLE ('',( #61530 ) ) ; +#62030 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76647 ), #42426 ) ; +#62033 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#62032 = PLANE ( 'NONE', #13495 ) ; +#62034 = LINE ( 'NONE', #23216, #61899 ) ; +#62035 = VECTOR ( 'NONE', #14446, 1000.000000000000000 ) ; +#62036 = FILL_AREA_STYLE ('',( #92608 ) ) ; +#62037 = LINE ( 'NONE', #93108, #23513 ) ; +#62038 = CARTESIAN_POINT ( 'NONE', ( -1.056623704877649894, -0.9836087549443109923, 0.8100000000000000533 ) ) ; +#62039 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62040 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62041 = PLANE ( 'NONE', #60982 ) ; +#62042 = LINE ( 'NONE', #5833, #40593 ) ; +#62043 = ORIENTED_EDGE ( 'NONE', *, *, #6898, .T. ) ; +#62044 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62045 = STYLED_ITEM ( 'NONE', ( #85492 ), #64627 ) ; +#62046 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#62047 = EDGE_CURVE ( 'NONE', #87713, #5810, #66787, .T. ) ; +#62048 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14673 ), #99387 ) ; +#62049 = PRESENTATION_STYLE_ASSIGNMENT (( #70168 ) ) ; +#62050 = LINE ( 'NONE', #7803, #32521 ) ; +#62051 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36390, 'distance_accuracy_value', 'NONE'); +#62052 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#62053 = VECTOR ( 'NONE', #92997, 1000.000000000000000 ) ; +#62054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62055 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.500000000000000444, 0.000000000000000000 ) ) ; +#62056 = PLANE ( 'NONE', #74700 ) ; +#62057 = PRESENTATION_STYLE_ASSIGNMENT (( #12607 ) ) ; +#62058 = ORIENTED_EDGE ( 'NONE', *, *, #21409, .T. ) ; +#62059 = ADVANCED_FACE ( 'NONE', ( #12601 ), #43814, .T. ) ; +#62060 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62061 = PRESENTATION_STYLE_ASSIGNMENT (( #30878 ) ) ; +#62062 = SURFACE_STYLE_FILL_AREA ( #7319 ) ; +#62063 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.5000000000000000000, -0.02000000000003350487 ) ) ; +#62064 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.876179938779915179, 0.000000000000000000 ) ) ; +#62065 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#62066 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62067 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26208 ) ) ; +#62068 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#62069 = EDGE_CURVE ( 'NONE', #9730, #72772, #23359, .T. ) ; +#62070 = FILL_AREA_STYLE_COLOUR ( '', #41924 ) ; +#62071 = AXIS2_PLACEMENT_3D ( 'NONE', #11479, #11985, #66202 ) ; +#62072 = SURFACE_STYLE_USAGE ( .BOTH. , #86023 ) ; +#62073 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#62074 = FACE_OUTER_BOUND ( 'NONE', #43008, .T. ) ; +#62075 = LINE ( 'NONE', #37580, #47207 ) ; +#62076 = PLANE ( 'NONE', #89405 ) ; +#62077 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#62078 = EDGE_CURVE ( 'NONE', #9281, #84427, #60617, .T. ) ; +#62079 = VERTEX_POINT ( 'NONE', #37679 ) ; +#62080 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62081 = LINE ( 'NONE', #93150, #86465 ) ; +#62082 = LINE ( 'NONE', #32936, #42246 ) ; +#62083 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62084 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8991599999999999593 ) ) ; +#62085 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62086 = ADVANCED_FACE ( 'NONE', ( #78475 ), #68774, .T. ) ; +#62087 = CARTESIAN_POINT ( 'NONE', ( -1.067393514141900202, -1.172828961844079920, 0.8100000000000000533 ) ) ; +#62088 = EDGE_LOOP ( 'NONE', ( #29254, #34132, #28802, #1582 ) ) ; +#62089 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#62090 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#62091 = AXIS2_PLACEMENT_3D ( 'NONE', #73332, #28361, #34542 ) ; +#62092 = AXIS2_PLACEMENT_3D ( 'NONE', #27425, #80057, #56585 ) ; +#62093 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62094 = ORIENTED_EDGE ( 'NONE', *, *, #33230, .T. ) ; +#62095 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62096 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4663, #13256, #98030, #99010 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#62097 = EDGE_CURVE ( 'NONE', #55931, #39851, #55019, .T. ) ; +#62098 = EDGE_CURVE ( 'NONE', #66816, #18416, #39672, .T. ) ; +#62099 = DIRECTION ( 'NONE', ( 0.7071072811865697361, 0.7071062811861716924, 0.000000000000000000 ) ) ; +#62100 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45694 ), #78396 ) ; +#62101 = VECTOR ( 'NONE', #75808, 1000.000000000000000 ) ; +#62102 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62103 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62104 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62105 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.399999999999999911, -11.57000000000000028 ) ) ; +#62106 = SURFACE_STYLE_FILL_AREA ( #64098 ) ; +#62107 = EDGE_LOOP ( 'NONE', ( #82628, #37376, #64008, #16060 ) ) ; +#62108 = EDGE_CURVE ( 'NONE', #60726, #38321, #2090, .T. ) ; +#62109 = EDGE_CURVE ( 'NONE', #45984, #52771, #84128, .T. ) ; +#62110 = FILL_AREA_STYLE ('',( #30924 ) ) ; +#62111 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49336, 'distance_accuracy_value', 'NONE'); +#62112 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#62113 = VECTOR ( 'NONE', #81206, 1000.000000000000000 ) ; +#62114 = CIRCLE ( 'NONE', #47437, 0.5799999999999999600 ) ; +#62115 = ORIENTED_EDGE ( 'NONE', *, *, #75247, .T. ) ; +#62116 = VERTEX_POINT ( 'NONE', #24897 ) ; +#62117 = EDGE_CURVE ( 'NONE', #27038, #5550, #64672, .T. ) ; +#62118 = FILL_AREA_STYLE_COLOUR ( '', #52128 ) ; +#62119 = SURFACE_SIDE_STYLE ('',( #92679 ) ) ; +#62120 = ORIENTED_EDGE ( 'NONE', *, *, #11005, .F. ) ; +#62121 = SURFACE_STYLE_USAGE ( .BOTH. , #21265 ) ; +#62122 = CARTESIAN_POINT ( 'NONE', ( 0.03293650051631569903, -1.463352833475739967, 0.8299999999999999600 ) ) ; +#62123 = PRESENTATION_STYLE_ASSIGNMENT (( #92682 ) ) ; +#62125 = EDGE_CURVE ( 'NONE', #47747, #88609, #87153, .T. ) ; +#62124 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.01500000000000000118, -0.2400000000000000189 ) ) ; +#62126 = LINE ( 'NONE', #38603, #74433 ) ; +#62127 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #47042, #84933 ) ; +#62128 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26261 ) ) ; +#62129 = VECTOR ( 'NONE', #92955, 1000.000000000000114 ) ; +#62130 = EDGE_LOOP ( 'NONE', ( #12643, #45478, #10401, #24957 ) ) ; +#62131 = SURFACE_STYLE_USAGE ( .BOTH. , #13045 ) ; +#62132 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86203, 'distance_accuracy_value', 'NONE'); +#62133 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62135 = CARTESIAN_POINT ( 'NONE', ( -2.276179938779915091, -3.100000000000000089, 0.000000000000000000 ) ) ; +#62134 = LINE ( 'NONE', #38128, #19878 ) ; +#62136 = PLANE ( 'NONE', #3960 ) ; +#62137 = ORIENTED_EDGE ( 'NONE', *, *, #7737, .T. ) ; +#62138 = SURFACE_SIDE_STYLE ('',( #38617 ) ) ; +#62139 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, 0.000000000000000000 ) ) ; +#62140 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62141 = EDGE_LOOP ( 'NONE', ( #88772, #61893, #58280, #76900 ) ) ; +#62143 = FILL_AREA_STYLE ('',( #7392 ) ) ; +#62142 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#62144 = ORIENTED_EDGE ( 'NONE', *, *, #82484, .F. ) ; +#62145 = ORIENTED_EDGE ( 'NONE', *, *, #50364, .T. ) ; +#62146 = PLANE ( 'NONE', #33109 ) ; +#62147 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8199999999999999512 ) ) ; +#62149 = EDGE_CURVE ( 'NONE', #5017, #11704, #80507, .T. ) ; +#62148 = CARTESIAN_POINT ( 'NONE', ( 0.1073457792207790085, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#62151 = ORIENTED_EDGE ( 'NONE', *, *, #76243, .F. ) ; +#62150 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62152 = LINE ( 'NONE', #78442, #85769 ) ; +#62153 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#62154 = FILL_AREA_STYLE_COLOUR ( '', #37670 ) ; +#62155 = ORIENTED_EDGE ( 'NONE', *, *, #98034, .F. ) ; +#62157 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#62156 = FACE_OUTER_BOUND ( 'NONE', #94993, .T. ) ; +#62158 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62159 = ORIENTED_EDGE ( 'NONE', *, *, #18074, .F. ) ; +#62160 = EDGE_CURVE ( 'NONE', #72195, #44288, #10961, .T. ) ; +#62161 = VERTEX_POINT ( 'NONE', #64177 ) ; +#62163 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62162 = CARTESIAN_POINT ( 'NONE', ( 1.089506002794699890, -1.495173285438690103, 0.8100000000000000533 ) ) ; +#62164 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62165 = LINE ( 'NONE', #55005, #89902 ) ; +#62166 = CARTESIAN_POINT ( 'NONE', ( -0.02181523387524260046, -1.116141175150469955, 0.8299999999999999600 ) ) ; +#62167 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #60094 ) ; +#62168 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#62169 = FACE_OUTER_BOUND ( 'NONE', #70149, .T. ) ; +#62170 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49115 ) ) ; +#62171 = ORIENTED_EDGE ( 'NONE', *, *, #56599, .F. ) ; +#62172 = FACE_OUTER_BOUND ( 'NONE', #65132, .T. ) ; +#62173 = EDGE_LOOP ( 'NONE', ( #56763, #46240, #100734, #28922 ) ) ; +#62174 = EDGE_CURVE ( 'NONE', #78858, #35525, #32019, .T. ) ; +#62176 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666653285, 1.100000000000000089, 0.000000000000000000 ) ) ; +#62175 = LINE ( 'NONE', #86117, #94581 ) ; +#62177 = VECTOR ( 'NONE', #1099, 1000.000000000000000 ) ; +#62178 = SURFACE_SIDE_STYLE ('',( #22327 ) ) ; +#62179 = SURFACE_STYLE_USAGE ( .BOTH. , #76964 ) ; +#62180 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50642 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1115, #86898, #87389 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62181 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62182 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 2.258754526011470139E-17 ) ) ; +#62183 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62184 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8648700000000000276 ) ) ; +#62185 = EDGE_LOOP ( 'NONE', ( #39502, #4801, #76891, #72949 ) ) ; +#62186 = EDGE_CURVE ( 'NONE', #99548, #4760, #19165, .T. ) ; +#62187 = VECTOR ( 'NONE', #47155, 1000.000000000000000 ) ; +#62188 = PLANE ( 'NONE', #42843 ) ; +#62189 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#62190 = SURFACE_STYLE_USAGE ( .BOTH. , #15661 ) ; +#62191 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146563249, 0.3100465759269648847, 0.8299999999999999600 ) ) ; +#62192 = CIRCLE ( 'NONE', #70311, 0.02999999999999997113 ) ; +#62193 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#62194 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#62195 = FILL_AREA_STYLE_COLOUR ( '', #4980 ) ; +#62196 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62197 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62198 = PRESENTATION_STYLE_ASSIGNMENT (( #85132 ) ) ; +#62199 = STYLED_ITEM ( 'NONE', ( #50269 ), #64894 ) ; +#62200 = PRESENTATION_STYLE_ASSIGNMENT (( #56561 ) ) ; +#62201 = VECTOR ( 'NONE', #1937, 1000.000000000000000 ) ; +#62202 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62203 = ADVANCED_FACE ( 'NONE', ( #18167 ), #57546, .T. ) ; +#62204 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#62206 = ADVANCED_FACE ( 'NONE', ( #24389 ), #55533, .F. ) ; +#62205 = PRESENTATION_STYLE_ASSIGNMENT (( #47358 ) ) ; +#62207 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.004999999999999986226, -0.2399999999999999911 ) ) ; +#62208 = ORIENTED_EDGE ( 'NONE', *, *, #47089, .F. ) ; +#62209 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62210 = SURFACE_STYLE_USAGE ( .BOTH. , #95680 ) ; +#62211 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666667052, 2.700000000000000178, 0.000000000000000000 ) ) ; +#62212 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62213 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#62214 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.300000000000000266, 0.8299999999999999600 ) ) ; +#62215 = CARTESIAN_POINT ( 'NONE', ( 1.086082380596258279, -0.9871347208242030602, 0.8099999999999980549 ) ) ; +#62216 = EDGE_CURVE ( 'NONE', #76167, #45738, #3401, .T. ) ; +#62217 = ORIENTED_EDGE ( 'NONE', *, *, #58722, .F. ) ; +#62218 = VECTOR ( 'NONE', #2332, 1000.000000000000000 ) ; +#62219 = CARTESIAN_POINT ( 'NONE', ( -0.8560791624706871605, 0.5647286298174479802, 0.8299999999999999600 ) ) ; +#62220 = EDGE_CURVE ( 'NONE', #5457, #33332, #42697, .T. ) ; +#62221 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.50000000000000000, 0.000000000000000000 ) ) ; +#62222 = ADVANCED_FACE ( 'NONE', ( #11454 ), #44182, .F. ) ; +#62223 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#62224 = SURFACE_STYLE_USAGE ( .BOTH. , #31556 ) ; +#62225 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62226 = EDGE_LOOP ( 'NONE', ( #23715, #78915, #59879, #66868, #11417, #71257 ) ) ; +#62227 = VERTEX_POINT ( 'NONE', #19714 ) ; +#62228 = ADVANCED_FACE ( 'NONE', ( #19191 ), #50879, .T. ) ; +#62229 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#62230 = ORIENTED_EDGE ( 'NONE', *, *, #93799, .T. ) ; +#62231 = CARTESIAN_POINT ( 'NONE', ( -0.03878568267182790075, 1.364454123474860170, 0.8100000000000000533 ) ) ; +#62232 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#62233 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -9.880000000000000782, 0.4000000000000000222 ) ) ; +#62234 = ADVANCED_FACE ( 'NONE', ( #52877 ), #47593, .T. ) ; +#62235 = FACE_OUTER_BOUND ( 'NONE', #2836, .T. ) ; +#62236 = SHAPE_DEFINITION_REPRESENTATION ( #18798, #99561 ) ; +#62237 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.05000000000000002359, 0.1900000000000000022 ) ) ; +#62238 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000500, 6.612910450713249105E-17, 1.000000000000000000 ) ) ; +#62240 = ORIENTED_EDGE ( 'NONE', *, *, #64734, .T. ) ; +#62239 = ORIENTED_EDGE ( 'NONE', *, *, #65036, .T. ) ; +#62241 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91913 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16146, #94763, #93238 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62242 = VERTEX_POINT ( 'NONE', #5842 ) ; +#62243 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#62244 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3883, 'distance_accuracy_value', 'NONE'); +#62246 = SURFACE_STYLE_FILL_AREA ( #9532 ) ; +#62245 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#62247 = ORIENTED_EDGE ( 'NONE', *, *, #80205, .T. ) ; +#62248 = VECTOR ( 'NONE', #67484, 1000.000000000000000 ) ; +#62249 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.600000000000000089, -0.2000000000000000111 ) ) ; +#62250 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62251 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4283 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87292, #18329, #12122 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62252 = ORIENTED_EDGE ( 'NONE', *, *, #60908, .T. ) ; +#62253 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62254 = VERTEX_POINT ( 'NONE', #60552 ) ; +#62255 = ORIENTED_EDGE ( 'NONE', *, *, #97316, .F. ) ; +#62256 = FILL_AREA_STYLE ('',( #438 ) ) ; +#62257 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60653 ) ) ; +#62258 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#62259 = FILL_AREA_STYLE_COLOUR ( '', #74983 ) ; +#62260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8360 ), #65509 ) ; +#62262 = EDGE_LOOP ( 'NONE', ( #27866, #26498, #46098, #87704, #40658, #58145 ) ) ; +#62261 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62263 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#62264 = FILL_AREA_STYLE_COLOUR ( '', #88030 ) ; +#62265 = ORIENTED_EDGE ( 'NONE', *, *, #25123, .T. ) ; +#62266 = ORIENTED_EDGE ( 'NONE', *, *, #46453, .T. ) ; +#62267 = ADVANCED_FACE ( 'NONE', ( #38927 ), #16922, .T. ) ; +#62268 = ORIENTED_EDGE ( 'NONE', *, *, #3415, .F. ) ; +#62269 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62270 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62271 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#62272 = AXIS2_PLACEMENT_3D ( 'NONE', #48259, #34949, #66079 ) ; +#62273 = CARTESIAN_POINT ( 'NONE', ( -0.4015417829630419932, -1.199500944507529976, 0.8299999999999999600 ) ) ; +#62275 = VECTOR ( 'NONE', #97829, 1000.000000000000000 ) ; +#62274 = PLANE ( 'NONE', #73883 ) ; +#62276 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62277 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, -0.02000000000002515044 ) ) ; +#62278 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17058, 'distance_accuracy_value', 'NONE'); +#62279 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#62280 = ORIENTED_EDGE ( 'NONE', *, *, #26392, .F. ) ; +#62281 = PRESENTATION_STYLE_ASSIGNMENT (( #22444 ) ) ; +#62282 = FILL_AREA_STYLE_COLOUR ( '', #77229 ) ; +#62283 = ORIENTED_EDGE ( 'NONE', *, *, #26684, .T. ) ; +#62284 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62285 = FILL_AREA_STYLE_COLOUR ( '', #50546 ) ; +#62286 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#62287 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62288 = FILL_AREA_STYLE ('',( #31129 ) ) ; +#62289 = CARTESIAN_POINT ( 'NONE', ( 1.745101982296789922, -0.9718760589866800581, 0.8299999999999999600 ) ) ; +#62290 = PRESENTATION_STYLE_ASSIGNMENT (( #31130 ) ) ; +#62291 = CYLINDRICAL_SURFACE ( 'NONE', #17266, 0.04999999999999999584 ) ; +#62293 = ADVANCED_FACE ( 'NONE', ( #63930 ), #79247, .T. ) ; +#62292 = SURFACE_STYLE_USAGE ( .BOTH. , #38792 ) ; +#62294 = SURFACE_STYLE_USAGE ( .BOTH. , #91525 ) ; +#62295 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98478, #47322, #91405 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62296 = AXIS2_PLACEMENT_3D ( 'NONE', #79173, #63376, #50071 ) ; +#62297 = SURFACE_SIDE_STYLE ('',( #31137 ) ) ; +#62298 = SURFACE_STYLE_FILL_AREA ( #70423 ) ; +#62299 = FILL_AREA_STYLE_COLOUR ( '', #34979 ) ; +#62300 = EDGE_CURVE ( 'NONE', #99146, #66371, #3646, .T. ) ; +#62301 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45985 ), #75322 ) ; +#62302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56169, #56689, #11604 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62303 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57432 ), #19867 ) ; +#62304 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62306 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62305 = CARTESIAN_POINT ( 'NONE', ( 0.9400000000000000577, 0.1200000000000003147, 0.3500000000000000333 ) ) ; +#62307 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62308 = CYLINDRICAL_SURFACE ( 'NONE', #46972, 0.04999999999999991257 ) ; +#62309 = STYLED_ITEM ( 'NONE', ( #61619 ), #58796 ) ; +#62310 = AXIS2_PLACEMENT_3D ( 'NONE', #62038, #93110, #54882 ) ; +#62311 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33474 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61119, #48326, #71784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62312 = EDGE_LOOP ( 'NONE', ( #65871, #9780, #89870, #96988 ) ) ; +#62313 = ADVANCED_FACE ( 'NONE', ( #27155 ), #26647, .T. ) ; +#62314 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98365, 'distance_accuracy_value', 'NONE'); +#62315 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77473, 'distance_accuracy_value', 'NONE'); +#62316 = LINE ( 'NONE', #8077, #46829 ) ; +#62317 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#62318 = SURFACE_SIDE_STYLE ('',( #54666 ) ) ; +#62319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62320 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62321 = CARTESIAN_POINT ( 'NONE', ( 13.17837699999999934, 9.889034999999999798, 0.8648700000000000276 ) ) ; +#62322 = SURFACE_SIDE_STYLE ('',( #63833 ) ) ; +#62323 = VERTEX_POINT ( 'NONE', #42467 ) ; +#62324 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62325 = ORIENTED_EDGE ( 'NONE', *, *, #93671, .T. ) ; +#62326 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#62328 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82195, 'distance_accuracy_value', 'NONE'); +#62327 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24665 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19028, #10794, #89003 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65058, 'distance_accuracy_value', 'NONE'); +#62330 = FILL_AREA_STYLE_COLOUR ( '', #22163 ) ; +#62331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62332 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62333 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62334 = EDGE_CURVE ( 'NONE', #1845, #93666, #74103, .T. ) ; +#62335 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62336 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 4.114543000000000283, 0.8648700000000000276 ) ) ; +#62337 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000020983, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#62338 = SURFACE_STYLE_FILL_AREA ( #54683 ) ; +#62339 = SURFACE_STYLE_FILL_AREA ( #70463 ) ; +#62340 = ORIENTED_EDGE ( 'NONE', *, *, #33390, .T. ) ; +#62341 = FILL_AREA_STYLE ('',( #100485 ) ) ; +#62342 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#62343 = FACE_OUTER_BOUND ( 'NONE', #59364, .T. ) ; +#62344 = VERTEX_POINT ( 'NONE', #88919 ) ; +#62345 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11392 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74484, #97894, #90280 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62346 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28093 ), #8441 ) ; +#62347 = VERTEX_POINT ( 'NONE', #96039 ) ; +#62348 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#62349 = VECTOR ( 'NONE', #83841, 1000.000000000000000 ) ; +#62350 = CARTESIAN_POINT ( 'NONE', ( 1.058713228792119931, -1.379057077391790287, 0.8100000000000000533 ) ) ; +#62351 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.000000000000000000 ) ) ; +#62352 = EDGE_CURVE ( 'NONE', #96560, #68999, #73597, .T. ) ; +#62353 = SURFACE_SIDE_STYLE ('',( #70478 ) ) ; +#62354 = CARTESIAN_POINT ( 'NONE', ( 1.877682030168900118, -1.070769809704489983, 0.8299999999999999600 ) ) ; +#62355 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999999556, -3.123820061220045297, 0.000000000000000000 ) ) ; +#62356 = CARTESIAN_POINT ( 'NONE', ( 9.974076750249974310, 3.548858249750026062, 0.8991599999999999593 ) ) ; +#62358 = ORIENTED_EDGE ( 'NONE', *, *, #33479, .F. ) ; +#62357 = ORIENTED_EDGE ( 'NONE', *, *, #70836, .F. ) ; +#62359 = STYLED_ITEM ( 'NONE', ( #31201 ), #45841 ) ; +#62360 = SURFACE_STYLE_USAGE ( .BOTH. , #68954 ) ; +#62361 = SURFACE_SIDE_STYLE ('',( #68958 ) ) ; +#62362 = ORIENTED_EDGE ( 'NONE', *, *, #78390, .F. ) ; +#62363 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62364 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62365 = ORIENTED_EDGE ( 'NONE', *, *, #6215, .F. ) ; +#62366 = VERTEX_POINT ( 'NONE', #65946 ) ; +#62367 = DIRECTION ( 'NONE', ( 0.7071067816865476141, -0.7071067806865475314, -0.000000000000000000 ) ) ; +#62368 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#62369 = CARTESIAN_POINT ( 'NONE', ( 1.663885285959190385, -1.121518536532950083, 0.8299999999999999600 ) ) ; +#62371 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -11.41999999999999993 ) ) ; +#62370 = LINE ( 'NONE', #93456, #65979 ) ; +#62372 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62373 = ORIENTED_EDGE ( 'NONE', *, *, #49858, .T. ) ; +#62374 = ORIENTED_EDGE ( 'NONE', *, *, #6582, .F. ) ; +#62375 = VECTOR ( 'NONE', #42436, 999.9999999999998863 ) ; +#62376 = ORIENTED_EDGE ( 'NONE', *, *, #15939, .F. ) ; +#62377 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67228 ), #16687 ) ; +#62378 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62379 = AXIS2_PLACEMENT_3D ( 'NONE', #8230, #100120, #15439 ) ; +#62380 = VECTOR ( 'NONE', #6748, 1000.000000000000000 ) ; +#62382 = ORIENTED_EDGE ( 'NONE', *, *, #7582, .T. ) ; +#62381 = PLANE ( 'NONE', #42840 ) ; +#62383 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89985 ) ) ; +#62384 = SURFACE_SIDE_STYLE ('',( #16364 ) ) ; +#62385 = ORIENTED_EDGE ( 'NONE', *, *, #87592, .T. ) ; +#62386 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62387 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#62388 = VERTEX_POINT ( 'NONE', #48623 ) ; +#62389 = EDGE_CURVE ( 'NONE', #89842, #79986, #9711, .T. ) ; +#62390 = VECTOR ( 'NONE', #63792, 1000.000000000000000 ) ; +#62391 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#62392 = AXIS2_PLACEMENT_3D ( 'NONE', #56581, #50923, #65722 ) ; +#62393 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#62395 = EDGE_LOOP ( 'NONE', ( #77532, #73443, #6562, #20524 ) ) ; +#62394 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.000000000000000000 ) ) ; +#62396 = CARTESIAN_POINT ( 'NONE', ( 1.302823766419570317, -0.9018902076549569768, 0.8299999999999998490 ) ) ; +#62397 = LINE ( 'NONE', #91999, #42164 ) ; +#62399 = CARTESIAN_POINT ( 'NONE', ( 1.652046208920949999, -1.504992180692799941, 0.8100000000000000533 ) ) ; +#62398 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#62400 = CARTESIAN_POINT ( 'NONE', ( -1.249457397435496553, -1.122836816814995808, 0.8099999999998975797 ) ) ; +#62401 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.299999999999999822, -0.02000000000003353609 ) ) ; +#62402 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62403 = CARTESIAN_POINT ( 'NONE', ( 1.759379393379719936, -1.230342595016630014, 0.8099999999999996092 ) ) ; +#62404 = ORIENTED_EDGE ( 'NONE', *, *, #72564, .T. ) ; +#62405 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62406 = SURFACE_STYLE_FILL_AREA ( #77703 ) ; +#62407 = SURFACE_STYLE_FILL_AREA ( #33275 ) ; +#62408 = AXIS2_PLACEMENT_3D ( 'NONE', #20499, #21500, #58858 ) ; +#62410 = SURFACE_STYLE_USAGE ( .BOTH. , #2137 ) ; +#62409 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62411 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000971, 0.1499999999999999944 ) ) ; +#62412 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#62413 = FACE_OUTER_BOUND ( 'NONE', #67070, .T. ) ; +#62414 = EDGE_CURVE ( 'NONE', #24305, #48640, #66434, .T. ) ; +#62415 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29799 ), #18353 ) ; +#62416 = LINE ( 'NONE', #60911, #91706 ) ; +#62417 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#62418 = ORIENTED_EDGE ( 'NONE', *, *, #31865, .F. ) ; +#62419 = STYLED_ITEM ( 'NONE', ( #10029 ), #47058 ) ; +#62420 = ORIENTED_EDGE ( 'NONE', *, *, #82158, .F. ) ; +#62423 = PLANE ( 'NONE', #26583 ) ; +#62422 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9369 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22700, #29844, #77311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62424 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.149999999999999911, 0.000000000000000000 ) ) ; +#62425 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.276179938779915091, 0.000000000000000000 ) ) ; +#62426 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21661 ), #65701 ) ; +#62427 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62428 = LINE ( 'NONE', #85887, #70548 ) ; +#62429 = ORIENTED_EDGE ( 'NONE', *, *, #47536, .F. ) ; +#62430 = CARTESIAN_POINT ( 'NONE', ( 1.702357802111380103, -0.9001170352889870108, 0.8100000000000008304 ) ) ; +#62431 = EDGE_CURVE ( 'NONE', #12846, #1586, #42944, .T. ) ; +#62432 = LINE ( 'NONE', #93514, #85379 ) ; +#62433 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62434 = CARTESIAN_POINT ( 'NONE', ( 1.166666666666660079, 3.500000000000000000, 0.000000000000000000 ) ) ; +#62435 = EDGE_CURVE ( 'NONE', #70676, #53201, #34320, .T. ) ; +#62436 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#62437 = FILL_AREA_STYLE_COLOUR ( '', #77055 ) ; +#62438 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62439 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46916 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16920, #71074, #48622 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62440 = CIRCLE ( 'NONE', #77068, 0.009999999999999998473 ) ; +#62441 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#62442 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62443 = FACE_OUTER_BOUND ( 'NONE', #61397, .T. ) ; +#62444 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#62445 = PRESENTATION_STYLE_ASSIGNMENT (( #54799 ) ) ; +#62446 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86926 ), #82060 ) ; +#62447 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57496, 'distance_accuracy_value', 'NONE'); +#62448 = STYLED_ITEM ( 'NONE', ( #2183 ), #96678 ) ; +#62449 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8991599999999999593 ) ) ; +#62450 = EDGE_LOOP ( 'NONE', ( #55190, #4940, #14310, #19906 ) ) ; +#62451 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000812, -0.1400000000000008737 ) ) ; +#62453 = ORIENTED_EDGE ( 'NONE', *, *, #18309, .F. ) ; +#62452 = AXIS2_PLACEMENT_3D ( 'NONE', #91978, #99554, #15351 ) ; +#62454 = FILL_AREA_STYLE_COLOUR ( '', #33960 ) ; +#62455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14571, 'distance_accuracy_value', 'NONE'); +#62456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16604, 'distance_accuracy_value', 'NONE'); +#62457 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37950 ), #8478 ) ; +#62458 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62459 = LINE ( 'NONE', #55315, #34881 ) ; +#62460 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62461 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#62462 = EDGE_CURVE ( 'NONE', #36233, #23378, #56800, .T. ) ; +#62463 = FILL_AREA_STYLE_COLOUR ( '', #29288 ) ; +#62464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7866 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83225, #6534, #44376 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62465 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8648700000000000276 ) ) ; +#62466 = LINE ( 'NONE', #29773, #37449 ) ; +#62467 = ORIENTED_EDGE ( 'NONE', *, *, #83709, .T. ) ; +#62468 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584400679, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#62469 = PLANE ( 'NONE', #66598 ) ; +#62470 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87888, 'distance_accuracy_value', 'NONE'); +#62471 = SURFACE_STYLE_USAGE ( .BOTH. , #24174 ) ; +#62472 = VERTEX_POINT ( 'NONE', #65413 ) ; +#62473 = CARTESIAN_POINT ( 'NONE', ( 1.167728355359882508, -1.217863928316313071, 0.8099999999998526157 ) ) ; +#62474 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62475 = ORIENTED_EDGE ( 'NONE', *, *, #70133, .F. ) ; +#62476 = SURFACE_STYLE_FILL_AREA ( #32323 ) ; +#62477 = FILL_AREA_STYLE ('',( #31299 ) ) ; +#62478 = ADVANCED_FACE ( 'NONE', ( #20973 ), #43950, .F. ) ; +#62479 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62480 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62482 = ORIENTED_EDGE ( 'NONE', *, *, #99302, .F. ) ; +#62481 = STYLED_ITEM ( 'NONE', ( #22957 ), #70656 ) ; +#62483 = SURFACE_STYLE_USAGE ( .BOTH. , #24705 ) ; +#62484 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62485 = ORIENTED_EDGE ( 'NONE', *, *, #88360, .T. ) ; +#62486 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62487 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62488 = STYLED_ITEM ( 'NONE', ( #21697 ), #88107 ) ; +#62489 = PLANE ( 'NONE', #67430 ) ; +#62490 = ORIENTED_EDGE ( 'NONE', *, *, #85219, .T. ) ; +#62491 = VERTEX_POINT ( 'NONE', #75596 ) ; +#62492 = PRESENTATION_STYLE_ASSIGNMENT (( #25229 ) ) ; +#62493 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10182 ) ) ; +#62494 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81537 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72628, #10750, #96587 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62495 = EDGE_LOOP ( 'NONE', ( #50772, #70337, #87451, #36338 ) ) ; +#62496 = ADVANCED_FACE ( 'NONE', ( #44427 ), #51133, .T. ) ; +#62497 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62498 = ORIENTED_EDGE ( 'NONE', *, *, #95107, .T. ) ; +#62500 = VERTEX_POINT ( 'NONE', #4632 ) ; +#62499 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62501 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#62503 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#62502 = CYLINDRICAL_SURFACE ( 'NONE', #10080, 0.05000000000000012768 ) ; +#62504 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62505 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62506 = VERTEX_POINT ( 'NONE', #29624 ) ; +#62507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62509 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.583333333333333481, 0.000000000000000000 ) ) ; +#62508 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62510 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8991599999999999593 ) ) ; +#62511 = EDGE_LOOP ( 'NONE', ( #85846, #23553, #14698, #75812, #78262, #87730 ) ) ; +#62512 = ADVANCED_FACE ( 'NONE', ( #76591 ), #91908, .T. ) ; +#62513 = FILL_AREA_STYLE_COLOUR ( '', #70994 ) ; +#62514 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#62515 = VECTOR ( 'NONE', #61183, 1000.000000000000000 ) ; +#62516 = SURFACE_STYLE_USAGE ( .BOTH. , #99670 ) ; +#62517 = VERTEX_POINT ( 'NONE', #45917 ) ; +#62518 = ADVANCED_FACE ( 'NONE', ( #46435 ), #77603, .F. ) ; +#62519 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#62520 = ORIENTED_EDGE ( 'NONE', *, *, #24993, .F. ) ; +#62521 = STYLED_ITEM ( 'NONE', ( #6555 ), #60554 ) ; +#62522 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75548 ), #52742 ) ; +#62523 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12742 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88825, #50059, #48535 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62525 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62524 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62526 = LINE ( 'NONE', #9805, #37663 ) ; +#62528 = ADVANCED_FACE ( 'NONE', ( #62821 ), #15273, .F. ) ; +#62527 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#62529 = AXIS2_PLACEMENT_3D ( 'NONE', #100893, #38751, #76541 ) ; +#62530 = VECTOR ( 'NONE', #98740, 1000.000000000000114 ) ; +#62531 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62532 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62533 = ORIENTED_EDGE ( 'NONE', *, *, #17777, .T. ) ; +#62534 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.000000000000000000, -1.149999999999999911 ) ) ; +#62535 = VERTEX_POINT ( 'NONE', #55664 ) ; +#62536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62537 = SURFACE_STYLE_FILL_AREA ( #9314 ) ; +#62538 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57723, 'distance_accuracy_value', 'NONE'); +#62539 = CIRCLE ( 'NONE', #23383, 0.3000000000000000444 ) ; +#62540 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62541 = SURFACE_SIDE_STYLE ('',( #23726 ) ) ; +#62542 = EDGE_CURVE ( 'NONE', #29448, #38462, #93389, .T. ) ; +#62544 = EDGE_CURVE ( 'NONE', #25590, #77663, #2203, .T. ) ; +#62543 = SURFACE_STYLE_USAGE ( .BOTH. , #93608 ) ; +#62545 = CARTESIAN_POINT ( 'NONE', ( 8.383086500500173344, 2.877106500500176356, 0.8991599999999999593 ) ) ; +#62546 = PRESENTATION_STYLE_ASSIGNMENT (( #23729 ) ) ; +#62547 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.123820061220075051, 0.000000000000000000 ) ) ; +#62548 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#62549 = ORIENTED_EDGE ( 'NONE', *, *, #22169, .T. ) ; +#62550 = FACE_OUTER_BOUND ( 'NONE', #11949, .T. ) ; +#62551 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62552 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72873 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14105, #23845, #53964 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62554 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62553 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62555 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.300000000000000266, 0.8299999999999999600 ) ) ; +#62556 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62557 = SURFACE_SIDE_STYLE ('',( #14507 ) ) ; +#62558 = CARTESIAN_POINT ( 'NONE', ( -1.263508545851719900, -1.411115659170130154, 0.8299999999999998490 ) ) ; +#62559 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#62560 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16793 ), #88619 ) ; +#62561 = FILL_AREA_STYLE_COLOUR ( '', #98180 ) ; +#62562 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62563 = ORIENTED_EDGE ( 'NONE', *, *, #17422, .F. ) ; +#62564 = EDGE_CURVE ( 'NONE', #67952, #97257, #85754, .T. ) ; +#62565 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62566 = ADVANCED_FACE ( 'NONE', ( #64805 ), #41840, .T. ) ; +#62567 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62568 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62569 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.01000000000000000021, -1.250000000000000000 ) ) ; +#62570 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62571 = FILL_AREA_STYLE ('',( #243 ) ) ; +#62572 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, 0.000000000000000000 ) ) ; +#62573 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#62574 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#62575 = VECTOR ( 'NONE', #3551, 1000.000000000000000 ) ; +#62576 = CARTESIAN_POINT ( 'NONE', ( -0.7229898940154579901, 0.6774732877316049784, 0.8100000000000000533 ) ) ; +#62577 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62578 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62579 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#62580 = SURFACE_SIDE_STYLE ('',( #30890 ) ) ; +#62581 = CIRCLE ( 'NONE', #54406, 0.4690439894930241160 ) ; +#62582 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62583 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#62584 = ORIENTED_EDGE ( 'NONE', *, *, #22991, .F. ) ; +#62585 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23319, 'distance_accuracy_value', 'NONE'); +#62586 = CARTESIAN_POINT ( 'NONE', ( -0.2892830278089179585, -1.420226250591691164, 0.8099999999996182476 ) ) ; +#62587 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#62588 = EDGE_CURVE ( 'NONE', #88976, #34710, #34198, .T. ) ; +#62589 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7566, #46436, #63820 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62590 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#62591 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#62592 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 8.286473000000000866, 0.8991599999999999593 ) ) ; +#62593 = CARTESIAN_POINT ( 'NONE', ( -1.102470388999849948, -1.163804091156239950, 0.8299999999999999600 ) ) ; +#62594 = ORIENTED_EDGE ( 'NONE', *, *, #19371, .F. ) ; +#62595 = SURFACE_STYLE_FILL_AREA ( #63093 ) ; +#62596 = EDGE_CURVE ( 'NONE', #44992, #50362, #57694, .T. ) ; +#62597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43387, 'distance_accuracy_value', 'NONE'); +#62599 = VECTOR ( 'NONE', #15000, 1000.000000000000000 ) ; +#62598 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62600 = VECTOR ( 'NONE', #84129, 1000.000000000000000 ) ; +#62601 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93498 ) ) ; +#62602 = VERTEX_POINT ( 'NONE', #2025 ) ; +#62603 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62604 = STYLED_ITEM ( 'NONE', ( #71642 ), #97234 ) ; +#62605 = EDGE_CURVE ( 'NONE', #64247, #75418, #17823, .T. ) ; +#62606 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62608 = EDGE_CURVE ( 'NONE', #89851, #85680, #65304, .T. ) ; +#62607 = LINE ( 'NONE', #16082, #49042 ) ; +#62609 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62610 = ORIENTED_EDGE ( 'NONE', *, *, #81196, .T. ) ; +#62611 = SURFACE_STYLE_USAGE ( .BOTH. , #31433 ) ; +#62612 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21027, 'distance_accuracy_value', 'NONE'); +#62613 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20077 ), #59353 ) ; +#62614 = FACE_OUTER_BOUND ( 'NONE', #79138, .T. ) ; +#62615 = ORIENTED_EDGE ( 'NONE', *, *, #21569, .T. ) ; +#62616 = FILL_AREA_STYLE ('',( #62118 ) ) ; +#62617 = SURFACE_SIDE_STYLE ('',( #31443 ) ) ; +#62618 = VERTEX_POINT ( 'NONE', #26025 ) ; +#62619 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62620 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62621 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#62622 = SURFACE_STYLE_USAGE ( .BOTH. , #31960 ) ; +#62623 = VECTOR ( 'NONE', #31708, 1000.000000000000114 ) ; +#62624 = LINE ( 'NONE', #91704, #49881 ) ; +#62625 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62626 = EDGE_CURVE ( 'NONE', #22324, #50963, #11096, .T. ) ; +#62627 = EDGE_LOOP ( 'NONE', ( #83275, #66858, #54464, #96370 ) ) ; +#62628 = LINE ( 'NONE', #30413, #81652 ) ; +#62630 = SURFACE_STYLE_FILL_AREA ( #15080 ) ; +#62629 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#62631 = STYLED_ITEM ( 'NONE', ( #34866 ), #53357 ) ; +#62632 = ADVANCED_FACE ( 'NONE', ( #88299 ), #85331, .T. ) ; +#62633 = ORIENTED_EDGE ( 'NONE', *, *, #12044, .F. ) ; +#62634 = EDGE_CURVE ( 'NONE', #84706, #27821, #99367, .T. ) ; +#62635 = SURFACE_STYLE_USAGE ( .BOTH. , #62138 ) ; +#62636 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.816666666666666652, 0.000000000000000000 ) ) ; +#62637 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84922 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22084, #24127, #93503 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62638 = LINE ( 'NONE', #23823, #89007 ) ; +#62639 = VERTEX_POINT ( 'NONE', #51538 ) ; +#62640 = ADVANCED_FACE ( 'NONE', ( #5485 ), #35704, .T. ) ; +#62642 = SURFACE_SIDE_STYLE ('',( #79465 ) ) ; +#62641 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#62643 = VERTEX_POINT ( 'NONE', #60680 ) ; +#62644 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3939 ) ) ; +#62645 = ORIENTED_EDGE ( 'NONE', *, *, #32661, .F. ) ; +#62646 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#62647 = SURFACE_STYLE_USAGE ( .BOTH. , #24351 ) ; +#62648 = SURFACE_STYLE_FILL_AREA ( #61642 ) ; +#62649 = ADVANCED_FACE ( 'NONE', ( #66806 ), #13113, .T. ) ; +#62650 = ORIENTED_EDGE ( 'NONE', *, *, #94574, .F. ) ; +#62651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91981 ) ) ; +#62652 = ORIENTED_EDGE ( 'NONE', *, *, #28832, .T. ) ; +#62654 = SURFACE_STYLE_FILL_AREA ( #38154 ) ; +#62653 = FILL_AREA_STYLE_COLOUR ( '', #79377 ) ; +#62655 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.1199999999999999956, -0.8499999999999999778 ) ) ; +#62656 = ORIENTED_EDGE ( 'NONE', *, *, #62108, .F. ) ; +#62657 = ORIENTED_EDGE ( 'NONE', *, *, #46834, .T. ) ; +#62658 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62659 = FILL_AREA_STYLE ('',( #23853 ) ) ; +#62660 = SURFACE_SIDE_STYLE ('',( #24370 ) ) ; +#62662 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77325 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75233, #29260, #66542 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62661 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93555 ) ) ; +#62663 = VECTOR ( 'NONE', #73976, 1000.000000000000000 ) ; +#62664 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 5.090351000000000070, 0.8648700000000000276 ) ) ; +#62665 = LINE ( 'NONE', #21822, #93139 ) ; +#62666 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96796 ), #20211 ) ; +#62667 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62668 = EDGE_CURVE ( 'NONE', #72797, #84398, #92766, .T. ) ; +#62669 = EDGE_CURVE ( 'NONE', #25261, #89045, #365, .T. ) ; +#62670 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96872 ) ) ; +#62671 = CARTESIAN_POINT ( 'NONE', ( 5.413238000000000660, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#62672 = VERTEX_POINT ( 'NONE', #85648 ) ; +#62673 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62675 = VECTOR ( 'NONE', #21906, 1000.000000000000000 ) ; +#62676 = CARTESIAN_POINT ( 'NONE', ( -0.7465345709966251242, 1.533618350106040085, 0.8100000000000000533 ) ) ; +#62677 = SURFACE_STYLE_USAGE ( .BOTH. , #56027 ) ; +#62678 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20914, #65883, #91357 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62679 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62680 = PRESENTATION_STYLE_ASSIGNMENT (( #85630 ) ) ; +#62681 = ORIENTED_EDGE ( 'NONE', *, *, #66820, .T. ) ; +#62682 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62683 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62684 = ADVANCED_FACE ( 'NONE', ( #55036 ), #38192, .F. ) ; +#62685 = SURFACE_SIDE_STYLE ('',( #99834 ) ) ; +#62686 = FACE_OUTER_BOUND ( 'NONE', #90093, .T. ) ; +#62687 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92340, 'distance_accuracy_value', 'NONE'); +#62688 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5558 ) ) ; +#62689 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62691 = CARTESIAN_POINT ( 'NONE', ( -0.5550755121431560912, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#62692 = PRESENTATION_STYLE_ASSIGNMENT (( #22874 ) ) ; +#62693 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62694 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#62695 = FILL_AREA_STYLE ('',( #31022 ) ) ; +#62696 = FILL_AREA_STYLE_COLOUR ( '', #60330 ) ; +#62697 = FACE_OUTER_BOUND ( 'NONE', #4593, .T. ) ; +#62698 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26846 ) ) ; +#62699 = SURFACE_STYLE_USAGE ( .BOTH. , #32046 ) ; +#62700 = FACE_OUTER_BOUND ( 'NONE', #67454, .T. ) ; +#62701 = LINE ( 'NONE', #38690, #49256 ) ; +#62702 = ORIENTED_EDGE ( 'NONE', *, *, #31752, .F. ) ; +#62703 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333323090, -0.2999999999999999889, 1.747825839084783216E-76 ) ) ; +#62704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67537 ) ) ; +#62705 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65263, 'distance_accuracy_value', 'NONE'); +#62706 = SURFACE_SIDE_STYLE ('',( #70332 ) ) ; +#62707 = CARTESIAN_POINT ( 'NONE', ( 1.400118793067939738, -1.229871795159537262, 0.8099999999998452882 ) ) ; +#62708 = VECTOR ( 'NONE', #72173, 1000.000000000000000 ) ; +#62709 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#62710 = FILL_AREA_STYLE ('',( #30498 ) ) ; +#62711 = STYLED_ITEM ( 'NONE', ( #22788 ), #77017 ) ; +#62712 = ORIENTED_EDGE ( 'NONE', *, *, #23712, .F. ) ; +#62713 = PRESENTATION_STYLE_ASSIGNMENT (( #100851 ) ) ; +#62714 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62715 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62716 = LINE ( 'NONE', #55582, #4701 ) ; +#62717 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18078, 'distance_accuracy_value', 'NONE'); +#62718 = FACE_OUTER_BOUND ( 'NONE', #86692, .T. ) ; +#62719 = VECTOR ( 'NONE', #86030, 1000.000000000000000 ) ; +#62720 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29042, 'distance_accuracy_value', 'NONE'); +#62721 = EDGE_CURVE ( 'NONE', #66967, #4744, #32040, .T. ) ; +#62722 = VECTOR ( 'NONE', #35840, 1000.000000000000114 ) ; +#62723 = FACE_OUTER_BOUND ( 'NONE', #58664, .T. ) ; +#62724 = VERTEX_POINT ( 'NONE', #23896 ) ; +#62725 = EDGE_LOOP ( 'NONE', ( #100527, #84066, #34463, #7540 ) ) ; +#62727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40578 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50987, #3994, #41806 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62726 = VECTOR ( 'NONE', #6753, 1000.000000000000000 ) ; +#62728 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #87766, #72430, #34178, #4005 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#62729 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62730 = SURFACE_STYLE_USAGE ( .BOTH. , #7487 ) ; +#62731 = EDGE_LOOP ( 'NONE', ( #45773, #48564, #64732, #52252 ) ) ; +#62732 = FILL_AREA_STYLE ('',( #92794 ) ) ; +#62733 = FILL_AREA_STYLE ('',( #7491 ) ) ; +#62734 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62735 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98612, 'distance_accuracy_value', 'NONE'); +#62736 = SURFACE_SIDE_STYLE ('',( #45836 ) ) ; +#62737 = SHAPE_DEFINITION_REPRESENTATION ( #88103, #19453 ) ; +#62738 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 1.979081000000000090, 0.8648700000000000276 ) ) ; +#62739 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#62742 = ORIENTED_EDGE ( 'NONE', *, *, #13829, .F. ) ; +#62741 = EDGE_LOOP ( 'NONE', ( #52721, #79278, #33917, #100158 ) ) ; +#62740 = EDGE_CURVE ( 'NONE', #68882, #4538, #92292, .T. ) ; +#62743 = ORIENTED_EDGE ( 'NONE', *, *, #67471, .F. ) ; +#62744 = AXIS2_PLACEMENT_3D ( 'NONE', #35302, #43918, #42920 ) ; +#62745 = SURFACE_STYLE_USAGE ( .BOTH. , #46877 ) ; +#62747 = SURFACE_SIDE_STYLE ('',( #47912 ) ) ; +#62746 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#62748 = ORIENTED_EDGE ( 'NONE', *, *, #51139, .F. ) ; +#62749 = EDGE_CURVE ( 'NONE', #81611, #7486, #43645, .T. ) ; +#62750 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62751 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#62753 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.187459415584420030, 0.8099999999999863975 ) ) ; +#62752 = SURFACE_STYLE_FILL_AREA ( #55103 ) ; +#62754 = VERTEX_POINT ( 'NONE', #62694 ) ; +#62756 = CARTESIAN_POINT ( 'NONE', ( 0.2165152913619279862, -0.9597720184016970135, 0.8100000000000000533 ) ) ; +#62755 = SURFACE_STYLE_USAGE ( .BOTH. , #54600 ) ; +#62757 = ORIENTED_EDGE ( 'NONE', *, *, #79229, .F. ) ; +#62758 = VERTEX_POINT ( 'NONE', #93765 ) ; +#62759 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#62760 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62761 = SURFACE_STYLE_USAGE ( .BOTH. , #440 ) ; +#62762 = VECTOR ( 'NONE', #87643, 1000.000000000000000 ) ; +#62764 = EDGE_CURVE ( 'NONE', #48640, #48176, #93269, .T. ) ; +#62763 = SURFACE_SIDE_STYLE ('',( #15220 ) ) ; +#62765 = ORIENTED_EDGE ( 'NONE', *, *, #2901, .T. ) ; +#62766 = PLANE ( 'NONE', #79234 ) ; +#62767 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#62768 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62769 = AXIS2_PLACEMENT_3D ( 'NONE', #66087, #51276, #74248 ) ; +#62770 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.383333333333326642, 1.747825839084889375E-76 ) ) ; +#62771 = AXIS2_PLACEMENT_3D ( 'NONE', #68398, #7045, #45394 ) ; +#62772 = ORIENTED_EDGE ( 'NONE', *, *, #78912, .F. ) ; +#62773 = PLANE ( 'NONE', #100443 ) ; +#62774 = ORIENTED_EDGE ( 'NONE', *, *, #74626, .T. ) ; +#62775 = EDGE_CURVE ( 'NONE', #9393, #93277, #69805, .T. ) ; +#62776 = VERTEX_POINT ( 'NONE', #24405 ) ; +#62778 = SURFACE_STYLE_FILL_AREA ( #93845 ) ; +#62777 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#62779 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.7833333856764529424, 0.6832601739883094050 ) ) ; +#62780 = SURFACE_STYLE_USAGE ( .BOTH. , #100909 ) ; +#62781 = VECTOR ( 'NONE', #29205, 1000.000000000000000 ) ; +#62782 = AXIS2_PLACEMENT_3D ( 'NONE', #1928, #93787, #40234 ) ; +#62783 = STYLED_ITEM ( 'NONE', ( #77064 ), #27033 ) ; +#62784 = SURFACE_STYLE_FILL_AREA ( #99458 ) ; +#62785 = EDGE_CURVE ( 'NONE', #41637, #53421, #7704, .T. ) ; +#62787 = ADVANCED_FACE ( 'NONE', ( #39692 ), #889, .T. ) ; +#62786 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#62788 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#62789 = ORIENTED_EDGE ( 'NONE', *, *, #91828, .T. ) ; +#62790 = PLANE ( 'NONE', #29429 ) ; +#62791 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62792 = ORIENTED_EDGE ( 'NONE', *, *, #14085, .T. ) ; +#62793 = LINE ( 'NONE', #25009, #31765 ) ; +#62794 = ADVANCED_FACE ( 'NONE', ( #10976 ), #95287, .T. ) ; +#62795 = ADVANCED_FACE ( 'NONE', ( #17698 ), #95798, .T. ) ; +#62796 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, -9.880000000000000782, 0.4000000000000000222 ) ) ; +#62797 = AXIS2_PLACEMENT_3D ( 'NONE', #77744, #46053, #100588 ) ; +#62798 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62799 = PRESENTATION_STYLE_ASSIGNMENT (( #54637 ) ) ; +#62801 = STYLED_ITEM ( 'NONE', ( #40857 ), #22180 ) ; +#62800 = CARTESIAN_POINT ( 'NONE', ( 1.769936080281629964, -0.9872600217210630857, 0.8299999999999999600 ) ) ; +#62802 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6700000000000000400, 0.2000000000000000111 ) ) ; +#62803 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71363, 'distance_accuracy_value', 'NONE'); +#62804 = FILL_AREA_STYLE ('',( #31629 ) ) ; +#62805 = PRESENTATION_STYLE_ASSIGNMENT (( #32660 ) ) ; +#62806 = FILL_AREA_STYLE ('',( #30108 ) ) ; +#62807 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62808 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62809 = EDGE_CURVE ( 'NONE', #58234, #96454, #34580, .T. ) ; +#62810 = AXIS2_PLACEMENT_3D ( 'NONE', #13482, #98747, #83521 ) ; +#62811 = SURFACE_STYLE_FILL_AREA ( #38797 ) ; +#62812 = SURFACE_STYLE_FILL_AREA ( #24008 ) ; +#62813 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62814 = PRESENTATION_STYLE_ASSIGNMENT (( #486 ) ) ; +#62815 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62816 = ADVANCED_FACE ( 'NONE', ( #79004 ), #40217, .T. ) ; +#62817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36710 ), #97008 ) ; +#62818 = PRESENTATION_STYLE_ASSIGNMENT (( #77599 ) ) ; +#62819 = LINE ( 'NONE', #85255, #43656 ) ; +#62820 = SURFACE_STYLE_USAGE ( .BOTH. , #21466 ) ; +#62821 = FACE_OUTER_BOUND ( 'NONE', #8857, .T. ) ; +#62822 = VECTOR ( 'NONE', #7266, 1000.000000000000000 ) ; +#62823 = FILL_AREA_STYLE_COLOUR ( '', #90247 ) ; +#62824 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35134 ), #98556 ) ; +#62825 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15682, 'distance_accuracy_value', 'NONE'); +#62826 = ORIENTED_EDGE ( 'NONE', *, *, #36262, .T. ) ; +#62827 = FACE_OUTER_BOUND ( 'NONE', #15169, .T. ) ; +#62828 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62829 = EDGE_LOOP ( 'NONE', ( #62549, #71275, #30692, #91335 ) ) ; +#62830 = LINE ( 'NONE', #61817, #79232 ) ; +#62831 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.4300000000264844191, 0.6499230724029858575 ) ) ; +#62832 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#62833 = FILL_AREA_STYLE ('',( #47474 ) ) ; +#62834 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2808578643762690841, -0.1499999999999999944 ) ) ; +#62835 = VECTOR ( 'NONE', #35790, 1000.000000000000000 ) ; +#62836 = FILL_AREA_STYLE_COLOUR ( '', #41583 ) ; +#62837 = VERTEX_POINT ( 'NONE', #68177 ) ; +#62838 = VECTOR ( 'NONE', #78666, 1000.000000000000000 ) ; +#62839 = ORIENTED_EDGE ( 'NONE', *, *, #81541, .F. ) ; +#62840 = EDGE_CURVE ( 'NONE', #47306, #2949, #81560, .T. ) ; +#62841 = SURFACE_SIDE_STYLE ('',( #30134 ) ) ; +#62842 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62843 = LINE ( 'NONE', #64332, #54272 ) ; +#62844 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62845 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62846 = STYLED_ITEM ( 'NONE', ( #92745 ), #54188 ) ; +#62847 = SURFACE_STYLE_FILL_AREA ( #14795 ) ; +#62848 = ADVANCED_FACE ( 'NONE', ( #43205 ), #75358, .T. ) ; +#62849 = ORIENTED_EDGE ( 'NONE', *, *, #32584, .F. ) ; +#62850 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62851 = CARTESIAN_POINT ( 'NONE', ( -0.7991630133853441231, 1.892059075926968870, 0.8100000000000000533 ) ) ; +#62852 = SURFACE_STYLE_USAGE ( .BOTH. , #61840 ) ; +#62853 = ORIENTED_EDGE ( 'NONE', *, *, #14736, .F. ) ; +#62854 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.123820061220075051, 0.000000000000000000 ) ) ; +#62855 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28065 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8006, #63269, #70370 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62856 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100168 ), #18793 ) ; +#62857 = LINE ( 'NONE', #54690, #64750 ) ; +#62858 = VERTEX_POINT ( 'NONE', #67671 ) ; +#62859 = FILL_AREA_STYLE ('',( #93429 ) ) ; +#62861 = CARTESIAN_POINT ( 'NONE', ( 1.145723413874399910, -1.437310919031880241, 0.8299999999999999600 ) ) ; +#62860 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55755, #86378, #8670, #47056 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#62862 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#62863 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#62864 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62865 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62866 = CARTESIAN_POINT ( 'NONE', ( 1.864761241546880166, -1.121240070007210043, 0.8100000000000000533 ) ) ; +#62867 = AXIS2_PLACEMENT_3D ( 'NONE', #49066, #64365, #9150 ) ; +#62868 = SURFACE_STYLE_FILL_AREA ( #77142 ) ; +#62869 = FILL_AREA_STYLE_COLOUR ( '', #95258 ) ; +#62871 = ORIENTED_EDGE ( 'NONE', *, *, #50247, .T. ) ; +#62870 = ORIENTED_EDGE ( 'NONE', *, *, #83170, .F. ) ; +#62872 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.5000000000000015543, 0.000000000000000000 ) ) ; +#62873 = ORIENTED_EDGE ( 'NONE', *, *, #44777, .T. ) ; +#62874 = ORIENTED_EDGE ( 'NONE', *, *, #8968, .T. ) ; +#62876 = EDGE_CURVE ( 'NONE', #93113, #26181, #97305, .T. ) ; +#62875 = ORIENTED_EDGE ( 'NONE', *, *, #50241, .T. ) ; +#62879 = VECTOR ( 'NONE', #11692, 1000.000000000000000 ) ; +#62878 = VECTOR ( 'NONE', #94493, 1000.000000000000000 ) ; +#62877 = SURFACE_SIDE_STYLE ('',( #55225 ) ) ; +#62880 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999995781, 1.048695503451053346E-76 ) ) ; +#62881 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62882 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62883 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#62885 = FACE_OUTER_BOUND ( 'NONE', #13968, .T. ) ; +#62884 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62886 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#62887 = ORIENTED_EDGE ( 'NONE', *, *, #13829, .T. ) ; +#62888 = ORIENTED_EDGE ( 'NONE', *, *, #50114, .T. ) ; +#62889 = FILL_AREA_STYLE_COLOUR ( '', #98993 ) ; +#62890 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33734 ) ) ; +#62891 = ORIENTED_EDGE ( 'NONE', *, *, #99950, .T. ) ; +#62892 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21888 ), #75900 ) ; +#62893 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#62894 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36782 ), #61294 ) ; +#62896 = ORIENTED_EDGE ( 'NONE', *, *, #41946, .T. ) ; +#62895 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#62897 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80829 ) ) ; +#62898 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62899 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62900 = FACE_OUTER_BOUND ( 'NONE', #65465, .T. ) ; +#62901 = VERTEX_POINT ( 'NONE', #50902 ) ; +#62902 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.900000000000000133, 0.000000000000000000 ) ) ; +#62903 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62904 = ORIENTED_EDGE ( 'NONE', *, *, #91861, .F. ) ; +#62905 = FACE_OUTER_BOUND ( 'NONE', #81311, .T. ) ; +#62906 = FILL_AREA_STYLE_COLOUR ( '', #67669 ) ; +#62907 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95427 ) ) ; +#62908 = ORIENTED_EDGE ( 'NONE', *, *, #63122, .T. ) ; +#62909 = SURFACE_SIDE_STYLE ('',( #53711 ) ) ; +#62910 = LINE ( 'NONE', #100059, #80886 ) ; +#62911 = PLANE ( 'NONE', #68670 ) ; +#62912 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62913 = AXIS2_PLACEMENT_3D ( 'NONE', #1618, #32754, #63898 ) ; +#62914 = VERTEX_POINT ( 'NONE', #5370 ) ; +#62915 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62916 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.449999999999999956, -11.82000000000000028 ) ) ; +#62917 = EDGE_CURVE ( 'NONE', #45275, #18237, #67187, .T. ) ; +#62918 = PRESENTATION_STYLE_ASSIGNMENT (( #61411 ) ) ; +#62919 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#62920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79222 ) ) ; +#62921 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20530 ) ) ; +#62922 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62923 = FILL_AREA_STYLE ('',( #85873 ) ) ; +#62924 = SURFACE_STYLE_USAGE ( .BOTH. , #71059 ) ; +#62925 = SURFACE_STYLE_FILL_AREA ( #64417 ) ; +#62926 = FILL_AREA_STYLE ('',( #8176 ) ) ; +#62927 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12650 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57631, #49433, #1466 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62928 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49886 ), #90599 ) ; +#62929 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62930 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.149999999999959499, 0.000000000000000000 ) ) ; +#62931 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49890 ) ) ; +#62932 = VERTEX_POINT ( 'NONE', #98759 ) ; +#62933 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61260 ), #56395 ) ; +#62934 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#62935 = EDGE_CURVE ( 'NONE', #22294, #18530, #91180, .T. ) ; +#62936 = ORIENTED_EDGE ( 'NONE', *, *, #79006, .T. ) ; +#62937 = FILL_AREA_STYLE_COLOUR ( '', #32469 ) ; +#62939 = DIRECTION ( 'NONE', ( -0.08767291364819880528, -0.9961493162234442700, 0.000000000000000000 ) ) ; +#62938 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62940 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#62941 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5864 ), #66200 ) ; +#62942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#62943 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62944 = ORIENTED_EDGE ( 'NONE', *, *, #65200, .F. ) ; +#62945 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#62946 = SURFACE_STYLE_USAGE ( .BOTH. , #7189 ) ; +#62947 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#62948 = DIRECTION ( 'NONE', ( 0.9200319872051170300, 0.3918432626949240327, 0.000000000000000000 ) ) ; +#62950 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62949 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62951 = SURFACE_STYLE_USAGE ( .BOTH. , #94008 ) ; +#62952 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62953 = FACE_OUTER_BOUND ( 'NONE', #72599, .T. ) ; +#62954 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#62955 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#62956 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8986 ) ) ; +#62957 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8648700000000000276 ) ) ; +#62958 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#62959 = EDGE_CURVE ( 'NONE', #75715, #98421, #83530, .T. ) ; +#62960 = SURFACE_SIDE_STYLE ('',( #26165 ) ) ; +#62961 = ORIENTED_EDGE ( 'NONE', *, *, #17205, .F. ) ; +#62962 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#62963 = ORIENTED_EDGE ( 'NONE', *, *, #93103, .T. ) ; +#62964 = AXIS2_PLACEMENT_3D ( 'NONE', #54735, #78199, #8145 ) ; +#62965 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#62966 = PRESENTATION_STYLE_ASSIGNMENT (( #32303 ) ) ; +#62967 = PRESENTATION_STYLE_ASSIGNMENT (( #84403 ) ) ; +#62968 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#62969 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#62970 = SURFACE_STYLE_USAGE ( .BOTH. , #56827 ) ; +#62971 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#62972 = CARTESIAN_POINT ( 'NONE', ( 0.05696903375467490122, -1.121240070007210043, 0.8299999999999999600 ) ) ; +#62973 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#62974 = SURFACE_STYLE_FILL_AREA ( #78760 ) ; +#62975 = EDGE_CURVE ( 'NONE', #7779, #92831, #75855, .T. ) ; +#62976 = ORIENTED_EDGE ( 'NONE', *, *, #97062, .T. ) ; +#62977 = PRESENTATION_STYLE_ASSIGNMENT (( #7718 ) ) ; +#62978 = FACE_OUTER_BOUND ( 'NONE', #90347, .T. ) ; +#62979 = LINE ( 'NONE', #55323, #84519 ) ; +#62980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#62981 = EDGE_LOOP ( 'NONE', ( #14993, #21936, #34527, #37250 ) ) ; +#62982 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000005773, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#62983 = VERTEX_POINT ( 'NONE', #61069 ) ; +#62984 = SURFACE_SIDE_STYLE ('',( #46076 ) ) ; +#62985 = VECTOR ( 'NONE', #336, 1000.000000000000000 ) ; +#62986 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.100000000000000089, -0.02000000000001120326 ) ) ; +#62987 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.1600000000000000033, -1.250000000000000000 ) ) ; +#62988 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#62989 = SURFACE_SIDE_STYLE ('',( #31813 ) ) ; +#62990 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#62991 = ORIENTED_EDGE ( 'NONE', *, *, #34882, .F. ) ; +#62992 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#62993 = FILL_AREA_STYLE_COLOUR ( '', #39721 ) ; +#62994 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20604 ), #1012 ) ; +#62995 = AXIS2_PLACEMENT_3D ( 'NONE', #14949, #22153, #29319 ) ; +#62996 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76522 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52248, #82377, #99588 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#62997 = ORIENTED_EDGE ( 'NONE', *, *, #28902, .F. ) ; +#62998 = AXIS2_PLACEMENT_3D ( 'NONE', #16002, #22685, #47167 ) ; +#62999 = FACE_OUTER_BOUND ( 'NONE', #39227, .T. ) ; +#63000 = FACE_OUTER_BOUND ( 'NONE', #11554, .T. ) ; +#63001 = LINE ( 'NONE', #32843, #60227 ) ; +#63002 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67568 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31988, #40667, #40165 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63003 = PLANE ( 'NONE', #77798 ) ; +#63004 = ORIENTED_EDGE ( 'NONE', *, *, #24412, .F. ) ; +#63005 = VERTEX_POINT ( 'NONE', #85522 ) ; +#63006 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63007 = EDGE_CURVE ( 'NONE', #56074, #16395, #37583, .T. ) ; +#63008 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100953 ) ; +#63009 = EDGE_LOOP ( 'NONE', ( #99314, #90124, #92572, #46847 ) ) ; +#63010 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5864 ) ) ; +#63011 = ORIENTED_EDGE ( 'NONE', *, *, #77647, .T. ) ; +#63013 = ORIENTED_EDGE ( 'NONE', *, *, #50644, .F. ) ; +#63012 = SURFACE_STYLE_FILL_AREA ( #30817 ) ; +#63014 = PLANE ( 'NONE', #65076 ) ; +#63015 = ORIENTED_EDGE ( 'NONE', *, *, #15919, .F. ) ; +#63016 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63017 = CARTESIAN_POINT ( 'NONE', ( 1.754677333481259982, -1.433486393616560273, 0.8099999999999997202 ) ) ; +#63018 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#63019 = ORIENTED_EDGE ( 'NONE', *, *, #42800, .F. ) ; +#63020 = EDGE_CURVE ( 'NONE', #4203, #78817, #22746, .T. ) ; +#63021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63022 = ADVANCED_FACE ( 'NONE', ( #39072 ), #70192, .F. ) ; +#63023 = SURFACE_STYLE_FILL_AREA ( #63529 ) ; +#63024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84148 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48275, #17581, #1799 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63025 = ORIENTED_EDGE ( 'NONE', *, *, #24205, .F. ) ; +#63027 = FACE_OUTER_BOUND ( 'NONE', #1015, .T. ) ; +#63026 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999512, 0.6599999999999999201, 0.9757359312880716784 ) ) ; +#63028 = VERTEX_POINT ( 'NONE', #100218 ) ; +#63029 = STYLED_ITEM ( 'NONE', ( #56183 ), #4902 ) ; +#63031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63030 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63032 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63033 = SURFACE_SIDE_STYLE ('',( #705 ) ) ; +#63034 = VECTOR ( 'NONE', #51844, 1000.000000000000000 ) ; +#63035 = SURFACE_SIDE_STYLE ('',( #94634 ) ) ; +#63037 = EDGE_CURVE ( 'NONE', #86964, #79461, #45678, .T. ) ; +#63036 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19983 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #172, #47656, #9770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63038 = ORIENTED_EDGE ( 'NONE', *, *, #2409, .F. ) ; +#63039 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#63040 = LINE ( 'NONE', #39032, #73587 ) ; +#63041 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000006176, -0.1400000000000000411 ) ) ; +#63042 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63043 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#63044 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 7.105604999999999727, 0.8991599999999999593 ) ) ; +#63045 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63046 = ORIENTED_EDGE ( 'NONE', *, *, #84585, .T. ) ; +#63047 = CARTESIAN_POINT ( 'NONE', ( -1.137533421400759970, -1.155903533527329996, 0.8300000000000002931 ) ) ; +#63048 = AXIS2_PLACEMENT_3D ( 'NONE', #34420, #10820, #73212 ) ; +#63051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63050 = FILL_AREA_STYLE ('',( #31885 ) ) ; +#63049 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63052 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89771, 'distance_accuracy_value', 'NONE'); +#63054 = SURFACE_STYLE_USAGE ( .BOTH. , #93620 ) ; +#63055 = FILL_AREA_STYLE ('',( #47716 ) ) ; +#63056 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95655 ), #53278 ) ; +#63057 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53567, #78050, #93321, #69861 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63058 = CARTESIAN_POINT ( 'NONE', ( 1.723820061220085353, 3.099999999999970335, 0.000000000000000000 ) ) ; +#63059 = PLANE ( 'NONE', #18276 ) ; +#63060 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#63061 = ORIENTED_EDGE ( 'NONE', *, *, #89916, .T. ) ; +#63062 = SURFACE_STYLE_FILL_AREA ( #85504 ) ; +#63063 = AXIS2_PLACEMENT_3D ( 'NONE', #39682, #880, #94281 ) ; +#63064 = FILL_AREA_STYLE ('',( #63573 ) ) ; +#63065 = STYLED_ITEM ( 'NONE', ( #95113 ), #83062 ) ; +#63066 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.000000000000000000 ) ) ; +#63067 = FACE_OUTER_BOUND ( 'NONE', #19997, .T. ) ; +#63068 = LINE ( 'NONE', #32417, #43573 ) ; +#63069 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25537 ) ) ; +#63070 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.000000000000000000 ) ) ; +#63071 = PRESENTATION_STYLE_ASSIGNMENT (( #6816 ) ) ; +#63072 = SURFACE_STYLE_USAGE ( .BOTH. , #23753 ) ; +#63073 = LINE ( 'NONE', #94158, #89134 ) ; +#63074 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63075 = EDGE_CURVE ( 'NONE', #42016, #81345, #15026, .T. ) ; +#63076 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63077 = LINE ( 'NONE', #2790, #84535 ) ; +#63078 = STYLED_ITEM ( 'NONE', ( #71835 ), #62203 ) ; +#63079 = ORIENTED_EDGE ( 'NONE', *, *, #87224, .T. ) ; +#63080 = LINE ( 'NONE', #7333, #62719 ) ; +#63081 = ORIENTED_EDGE ( 'NONE', *, *, #87436, .F. ) ; +#63082 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 4.344024262657780003E-34 ) ) ; +#63083 = STYLED_ITEM ( 'NONE', ( #35701 ), #40700 ) ; +#63085 = VECTOR ( 'NONE', #49797, 1000.000000000000000 ) ; +#63084 = CARTESIAN_POINT ( 'NONE', ( 0.1595320655217619954, -1.429044931969539967, 0.8299999999999999600 ) ) ; +#63086 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#63087 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#63088 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63089 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63090 = CARTESIAN_POINT ( 'NONE', ( -1.219528525021920107, -1.135808780994409961, 0.8100000000000000533 ) ) ; +#63091 = ADVANCED_FACE ( 'NONE', ( #54407, #46184 ), #77350, .F. ) ; +#63092 = ORIENTED_EDGE ( 'NONE', *, *, #6984, .T. ) ; +#63093 = FILL_AREA_STYLE ('',( #55938 ) ) ; +#63094 = PRESENTATION_STYLE_ASSIGNMENT (( #47750 ) ) ; +#63095 = VECTOR ( 'NONE', #77238, 1000.000000000000000 ) ; +#63096 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63097 = VERTEX_POINT ( 'NONE', #41106 ) ; +#63098 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90774 ) ) ; +#63100 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.4999999999999991673, 0.8299999999999999600 ) ) ; +#63101 = VECTOR ( 'NONE', #13827, 1000.000000000000000 ) ; +#63102 = LINE ( 'NONE', #78903, #57070 ) ; +#63103 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.123820061220055511, 0.000000000000000000 ) ) ; +#63104 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#63105 = ORIENTED_EDGE ( 'NONE', *, *, #1173, .T. ) ; +#63106 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63107 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63108 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89185 ) ) ; +#63109 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87002, 'distance_accuracy_value', 'NONE'); +#63110 = PRESENTATION_STYLE_ASSIGNMENT (( #31435 ) ) ; +#63111 = ORIENTED_EDGE ( 'NONE', *, *, #78827, .T. ) ; +#63112 = LINE ( 'NONE', #99407, #100074 ) ; +#63113 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63114 = FILL_AREA_STYLE_COLOUR ( '', #31252 ) ; +#63115 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38195 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90321, #5518, #67820 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63116 = ORIENTED_EDGE ( 'NONE', *, *, #17634, .T. ) ; +#63117 = LINE ( 'NONE', #71250, #99831 ) ; +#63118 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72875 ) ) ; +#63119 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.476179938779914824, 0.000000000000000000 ) ) ; +#63120 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#63121 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63122 = EDGE_CURVE ( 'NONE', #36462, #41918, #63077, .T. ) ; +#63123 = VECTOR ( 'NONE', #87260, 1000.000000000000000 ) ; +#63124 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35401, #88480, #10780, #89978 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63125 = VERTEX_POINT ( 'NONE', #42101 ) ; +#63126 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63127 = STYLED_ITEM ( 'NONE', ( #40079 ), #83958 ) ; +#63128 = VECTOR ( 'NONE', #84635, 1000.000000000000000 ) ; +#63129 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43018, 'distance_accuracy_value', 'NONE'); +#63130 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63131 = FACE_OUTER_BOUND ( 'NONE', #57741, .T. ) ; +#63132 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#63133 = ORIENTED_EDGE ( 'NONE', *, *, #75164, .T. ) ; +#63134 = EDGE_CURVE ( 'NONE', #96200, #79071, #32426, .T. ) ; +#63135 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82655 ), #58279 ) ; +#63136 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63137 = EDGE_CURVE ( 'NONE', #4168, #55353, #41603, .T. ) ; +#63138 = FACE_OUTER_BOUND ( 'NONE', #51696, .T. ) ; +#63139 = ORIENTED_EDGE ( 'NONE', *, *, #10146, .T. ) ; +#63140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28850 ) ) ; +#63141 = EDGE_CURVE ( 'NONE', #70651, #99535, #25784, .T. ) ; +#63142 = PRESENTATION_STYLE_ASSIGNMENT (( #31978 ) ) ; +#63143 = ORIENTED_EDGE ( 'NONE', *, *, #4936, .F. ) ; +#63144 = ORIENTED_EDGE ( 'NONE', *, *, #87459, .F. ) ; +#63145 = SURFACE_SIDE_STYLE ('',( #100778 ) ) ; +#63147 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#63146 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#63148 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63149 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63388 ) ) ; +#63150 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51650 ) ) ; +#63151 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, 0.000000000000000000 ) ) ; +#63152 = ORIENTED_EDGE ( 'NONE', *, *, #49632, .F. ) ; +#63153 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63154 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63155 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45160 ), #40335 ) ; +#63156 = STYLED_ITEM ( 'NONE', ( #56349 ), #16254 ) ; +#63157 = EDGE_CURVE ( 'NONE', #1345, #7626, #31914, .T. ) ; +#63158 = PLANE ( 'NONE', #94633 ) ; +#63159 = ORIENTED_EDGE ( 'NONE', *, *, #90923, .F. ) ; +#63161 = VECTOR ( 'NONE', #62850, 1000.000000000000000 ) ; +#63160 = LINE ( 'NONE', #77430, #33613 ) ; +#63162 = VERTEX_POINT ( 'NONE', #24284 ) ; +#63163 = ORIENTED_EDGE ( 'NONE', *, *, #25105, .T. ) ; +#63164 = CLOSED_SHELL ( 'NONE', ( #52017, #49831, #2628, #49993, #37287, #87415 ) ) ; +#63166 = SURFACE_STYLE_USAGE ( .BOTH. , #71815 ) ; +#63165 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63167 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#63168 = EDGE_CURVE ( 'NONE', #89851, #88016, #18065, .T. ) ; +#63169 = VECTOR ( 'NONE', #85788, 1000.000000000000000 ) ; +#63170 = FILL_AREA_STYLE_COLOUR ( '', #82506 ) ; +#63171 = CARTESIAN_POINT ( 'NONE', ( -1.275961121358871742, -0.9963620614099988337, 0.8099999999999907274 ) ) ; +#63172 = SURFACE_STYLE_FILL_AREA ( #40686 ) ; +#63173 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71308 ), #69604 ) ; +#63174 = FILL_AREA_STYLE_COLOUR ( '', #23095 ) ; +#63175 = LINE ( 'NONE', #41190, #32379 ) ; +#63176 = FACE_OUTER_BOUND ( 'NONE', #16726, .T. ) ; +#63177 = VECTOR ( 'NONE', #14218, 1000.000000000000000 ) ; +#63178 = EDGE_CURVE ( 'NONE', #50740, #15330, #78876, .T. ) ; +#63179 = ORIENTED_EDGE ( 'NONE', *, *, #61332, .T. ) ; +#63180 = SURFACE_STYLE_FILL_AREA ( #20827 ) ; +#63181 = EDGE_CURVE ( 'NONE', #16653, #80960, #40083, .T. ) ; +#63183 = FILL_AREA_STYLE ('',( #64170 ) ) ; +#63182 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#63184 = CARTESIAN_POINT ( 'NONE', ( -1.070550814989697841, -1.509576801066647933, 0.8099999999996125855 ) ) ; +#63185 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63186 = EDGE_CURVE ( 'NONE', #9228, #18378, #56443, .T. ) ; +#63187 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63188 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#63189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63190 = FILL_AREA_STYLE_COLOUR ( '', #52656 ) ; +#63191 = PRODUCT_DEFINITION ( 'δ֪', '', #33972, #19741 ) ; +#63192 = ORIENTED_EDGE ( 'NONE', *, *, #67018, .F. ) ; +#63193 = FILL_AREA_STYLE ('',( #39165 ) ) ; +#63194 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#63195 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63196 = SURFACE_STYLE_USAGE ( .BOTH. , #6457 ) ; +#63197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63198 = AXIS2_PLACEMENT_3D ( 'NONE', #20246, #89213, #73898 ) ; +#63199 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#63200 = VECTOR ( 'NONE', #17672, 1000.000000000000000 ) ; +#63201 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853448918, 0.2349715759269649928, 0.8299999999999999600 ) ) ; +#63202 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63203 = SURFACE_SIDE_STYLE ('',( #70316 ) ) ; +#63204 = EDGE_CURVE ( 'NONE', #3181, #85180, #72728, .T. ) ; +#63205 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#63206 = SURFACE_SIDE_STYLE ('',( #38681 ) ) ; +#63207 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#63208 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909090190, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#63209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63210 = SURFACE_STYLE_FILL_AREA ( #94798 ) ; +#63211 = VECTOR ( 'NONE', #25038, 1000.000000000000114 ) ; +#63212 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55121 ), #32216 ) ; +#63213 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#63214 = LINE ( 'NONE', #46833, #6243 ) ; +#63215 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, -0.004999999999999986226, -0.2500000000000000000 ) ) ; +#63216 = EDGE_CURVE ( 'NONE', #36363, #90254, #72226, .T. ) ; +#63217 = ORIENTED_EDGE ( 'NONE', *, *, #79123, .T. ) ; +#63218 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55048 ) ) ; +#63219 = SURFACE_STYLE_FILL_AREA ( #24416 ) ; +#63220 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63222 = PLANE ( 'NONE', #32381 ) ; +#63221 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#63223 = EDGE_CURVE ( 'NONE', #65172, #3550, #2300, .T. ) ; +#63224 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63225 = CARTESIAN_POINT ( 'NONE', ( 1.218309849891033192, -1.156541810439597251, 0.8099999999998914735 ) ) ; +#63226 = STYLED_ITEM ( 'NONE', ( #69747 ), #17046 ) ; +#63227 = SURFACE_SIDE_STYLE ('',( #23915 ) ) ; +#63228 = LINE ( 'NONE', #61708, #22178 ) ; +#63230 = ORIENTED_EDGE ( 'NONE', *, *, #41718, .F. ) ; +#63229 = VECTOR ( 'NONE', #6693, 1000.000000000000000 ) ; +#63231 = STYLED_ITEM ( 'NONE', ( #492 ), #62518 ) ; +#63232 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63233 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63234 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55065 ), #40411 ) ; +#63235 = SURFACE_STYLE_USAGE ( .BOTH. , #16695 ) ; +#63236 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#63237 = CLOSED_SHELL ( 'NONE', ( #6312, #16768, #21258, #78455, #79317, #31764 ) ) ; +#63238 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63239 = AXIS2_PLACEMENT_3D ( 'NONE', #77601, #23495, #54650 ) ; +#63240 = VERTEX_POINT ( 'NONE', #1269 ) ; +#63241 = ORIENTED_EDGE ( 'NONE', *, *, #10558, .T. ) ; +#63242 = VECTOR ( 'NONE', #89332, 1000.000000000000000 ) ; +#63243 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63244 = ORIENTED_EDGE ( 'NONE', *, *, #78899, .T. ) ; +#63245 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63246 = STYLED_ITEM ( 'NONE', ( #86379 ), #50373 ) ; +#63247 = FILL_AREA_STYLE_COLOUR ( '', #9071 ) ; +#63248 = SURFACE_SIDE_STYLE ('',( #69312 ) ) ; +#63249 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63250 = SURFACE_STYLE_USAGE ( .BOTH. , #40252 ) ; +#63251 = EDGE_CURVE ( 'NONE', #78062, #55587, #17572, .T. ) ; +#63252 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63253 = PRESENTATION_STYLE_ASSIGNMENT (( #14694 ) ) ; +#63254 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#63255 = FACE_OUTER_BOUND ( 'NONE', #42157, .T. ) ; +#63257 = ORIENTED_EDGE ( 'NONE', *, *, #40595, .T. ) ; +#63256 = VERTEX_POINT ( 'NONE', #55431 ) ; +#63258 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #37058 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #89714 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#63259 = VECTOR ( 'NONE', #70843, 1000.000000000000114 ) ; +#63260 = VERTEX_POINT ( 'NONE', #86543 ) ; +#63261 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50385, 'distance_accuracy_value', 'NONE'); +#63262 = CARTESIAN_POINT ( 'NONE', ( 1.755956893679319952, -1.501723168847330259, 0.8100000000000000533 ) ) ; +#63263 = FACE_OUTER_BOUND ( 'NONE', #5977, .T. ) ; +#63264 = ORIENTED_EDGE ( 'NONE', *, *, #82852, .T. ) ; +#63265 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000444, 0.000000000000000000 ) ) ; +#63266 = SURFACE_STYLE_FILL_AREA ( #85700 ) ; +#63267 = AXIS2_PLACEMENT_3D ( 'NONE', #11138, #33215, #49552 ) ; +#63268 = ORIENTED_EDGE ( 'NONE', *, *, #60908, .F. ) ; +#63270 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.000000000000000000 ) ) ; +#63269 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63271 = ORIENTED_EDGE ( 'NONE', *, *, #45153, .F. ) ; +#63272 = EDGE_CURVE ( 'NONE', #4744, #4168, #63589, .T. ) ; +#63274 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#63273 = SURFACE_STYLE_FILL_AREA ( #8510 ) ; +#63275 = ORIENTED_EDGE ( 'NONE', *, *, #39027, .F. ) ; +#63276 = ORIENTED_EDGE ( 'NONE', *, *, #81598, .T. ) ; +#63277 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40850 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77328, #8314, #70686 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63278 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.000000000000000000 ) ) ; +#63279 = FILL_AREA_STYLE_COLOUR ( '', #70063 ) ; +#63281 = ORIENTED_EDGE ( 'NONE', *, *, #24993, .T. ) ; +#63280 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#63282 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63283 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#63284 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63285 = VECTOR ( 'NONE', #93634, 1000.000000000000000 ) ; +#63286 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63287 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63288 = ORIENTED_EDGE ( 'NONE', *, *, #58779, .F. ) ; +#63290 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63289 = FILL_AREA_STYLE_COLOUR ( '', #32074 ) ; +#63291 = DIRECTION ( 'NONE', ( 0.000000000000000000, 4.266452400824600274E-34, 1.000000000000000000 ) ) ; +#63292 = ORIENTED_EDGE ( 'NONE', *, *, #35056, .F. ) ; +#63293 = VERTEX_POINT ( 'NONE', #79910 ) ; +#63294 = CARTESIAN_POINT ( 'NONE', ( 1.325735931288071434, 0.6892893218813450629, 1.099999999999999645 ) ) ; +#63295 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84015, #76333, #62064, #68165 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63296 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#63298 = ADVANCED_FACE ( 'NONE', ( #10341 ), #33954, .F. ) ; +#63297 = FACE_OUTER_BOUND ( 'NONE', #65115, .T. ) ; +#63299 = VECTOR ( 'NONE', #27761, 1000.000000000000000 ) ; +#63300 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#63301 = LINE ( 'NONE', #86753, #6807 ) ; +#63303 = VECTOR ( 'NONE', #49314, 999.9999999999998863 ) ; +#63302 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68408, 'distance_accuracy_value', 'NONE'); +#63304 = ADVANCED_FACE ( 'NONE', ( #13370 ), #35958, .F. ) ; +#63305 = FACE_OUTER_BOUND ( 'NONE', #54834, .T. ) ; +#63306 = VERTEX_POINT ( 'NONE', #44566 ) ; +#63307 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.499999999999980016, 0.1829999999999999960 ) ) ; +#63308 = STYLED_ITEM ( 'NONE', ( #55553 ), #62684 ) ; +#63309 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999994671, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#63310 = VERTEX_POINT ( 'NONE', #12871 ) ; +#63311 = ADVANCED_FACE ( 'NONE', ( #81918 ), #65560, .F. ) ; +#63312 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#63313 = VECTOR ( 'NONE', #80792, 1000.000000000000000 ) ; +#63314 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 8.392538999999999305, 0.8648700000000000276 ) ) ; +#63315 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63317 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.876179938779915179, 0.000000000000000000 ) ) ; +#63316 = FILL_AREA_STYLE_COLOUR ( '', #33268 ) ; +#63318 = CARTESIAN_POINT ( 'NONE', ( 1.798434352155980021, -1.039339352017210061, 0.8100000000000000533 ) ) ; +#63319 = SURFACE_STYLE_USAGE ( .BOTH. , #15781 ) ; +#63320 = CLOSED_SHELL ( 'NONE', ( #39518, #2893, #75195, #72445, #23205, #73590 ) ) ; +#63321 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63322 = FILL_AREA_STYLE_COLOUR ( '', #72328 ) ; +#63323 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63324 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, -3.099999999999969891, 0.000000000000000000 ) ) ; +#63325 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#63326 = FILL_AREA_STYLE_COLOUR ( '', #20250 ) ; +#63327 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63328 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63329 = STYLED_ITEM ( 'NONE', ( #70273 ), #14932 ) ; +#63330 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#63331 = STYLED_ITEM ( 'NONE', ( #79990 ), #50060 ) ; +#63332 = EDGE_CURVE ( 'NONE', #12027, #70604, #66081, .T. ) ; +#63333 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980549, 0.000000000000000000 ) ) ; +#63334 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#63335 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63336 = AXIS2_PLACEMENT_3D ( 'NONE', #72116, #2174, #15432 ) ; +#63337 = ORIENTED_EDGE ( 'NONE', *, *, #78824, .F. ) ; +#63338 = PRESENTATION_STYLE_ASSIGNMENT (( #54662 ) ) ; +#63339 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.699999999999999956, -0.02000000000000419845 ) ) ; +#63340 = ADVANCED_FACE ( 'NONE', ( #11362 ), #3788, .T. ) ; +#63341 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58803, 'distance_accuracy_value', 'NONE'); +#63342 = ORIENTED_EDGE ( 'NONE', *, *, #81884, .F. ) ; +#63344 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33953, 'distance_accuracy_value', 'NONE'); +#63343 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63345 = DIRECTION ( 'NONE', ( -4.344024262657780003E-34, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63346 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63348 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#63347 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #79314, .NOT_KNOWN. ) ; +#63349 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37238 ), #2972 ) ; +#63350 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.8999999999999991340, 4.860315062863665657E-79 ) ) ; +#63351 = AXIS2_PLACEMENT_3D ( 'NONE', #59939, #83394, #76211 ) ; +#63352 = EDGE_LOOP ( 'NONE', ( #9638, #16634, #4487, #5091 ) ) ; +#63353 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#63354 = ORIENTED_EDGE ( 'NONE', *, *, #72502, .F. ) ; +#63355 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63356 = EDGE_CURVE ( 'NONE', #35508, #37870, #69557, .T. ) ; +#63357 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31685, 'distance_accuracy_value', 'NONE'); +#63358 = LINE ( 'NONE', #39842, #84123 ) ; +#63359 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63360 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66127 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38378, #75654, #69478 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63361 = LINE ( 'NONE', #79150, #70578 ) ; +#63362 = CARTESIAN_POINT ( 'NONE', ( -0.1561074608318659962, -1.440618065759700084, 0.8299999999999995159 ) ) ; +#63363 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63364 = EDGE_CURVE ( 'NONE', #11287, #61128, #15933, .T. ) ; +#63365 = ORIENTED_EDGE ( 'NONE', *, *, #59077, .T. ) ; +#63366 = LINE ( 'NONE', #16824, #33788 ) ; +#63367 = ORIENTED_EDGE ( 'NONE', *, *, #95099, .T. ) ; +#63368 = SURFACE_STYLE_USAGE ( .BOTH. , #77645 ) ; +#63369 = ORIENTED_EDGE ( 'NONE', *, *, #76435, .F. ) ; +#63370 = CARTESIAN_POINT ( 'NONE', ( 1.194650275651319982, -1.445196667902379994, 0.8299999999999999600 ) ) ; +#63371 = EDGE_CURVE ( 'NONE', #82331, #54849, #37942, .T. ) ; +#63372 = EDGE_CURVE ( 'NONE', #61999, #82294, #38450, .T. ) ; +#63373 = PLANE ( 'NONE', #70747 ) ; +#63374 = AXIS2_PLACEMENT_3D ( 'NONE', #52599, #51616, #11670 ) ; +#63375 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63376 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63377 = AXIS2_PLACEMENT_3D ( 'NONE', #88191, #41230, #76603 ) ; +#63378 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000089, 2.676179938779915002, 0.000000000000000000 ) ) ; +#63380 = VERTEX_POINT ( 'NONE', #100585 ) ; +#63379 = VERTEX_POINT ( 'NONE', #83899 ) ; +#63381 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63383 = EDGE_CURVE ( 'NONE', #63765, #52560, #61945, .T. ) ; +#63382 = SURFACE_SIDE_STYLE ('',( #86836 ) ) ; +#63385 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#63384 = PRESENTATION_STYLE_ASSIGNMENT (( #71007 ) ) ; +#63386 = ORIENTED_EDGE ( 'NONE', *, *, #75455, .F. ) ; +#63387 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63388 = STYLED_ITEM ( 'NONE', ( #96712 ), #23600 ) ; +#63390 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#63389 = PRESENTATION_STYLE_ASSIGNMENT (( #85822 ) ) ; +#63391 = AXIS2_PLACEMENT_3D ( 'NONE', #86097, #836, #325 ) ; +#63392 = ORIENTED_EDGE ( 'NONE', *, *, #60473, .F. ) ; +#63393 = ORIENTED_EDGE ( 'NONE', *, *, #35008, .T. ) ; +#63394 = LINE ( 'NONE', #87847, #72597 ) ; +#63395 = SURFACE_STYLE_FILL_AREA ( #3596 ) ; +#63396 = ADVANCED_FACE ( 'NONE', ( #54803 ), #15429, .T. ) ; +#63397 = CARTESIAN_POINT ( 'NONE', ( -0.2052975279651420015, -1.010243534007990052, 0.8300000000000000711 ) ) ; +#63398 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63399 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63401 = VERTEX_POINT ( 'NONE', #23630 ) ; +#63400 = AXIS2_PLACEMENT_3D ( 'NONE', #11581, #4494, #20320 ) ; +#63402 = ORIENTED_EDGE ( 'NONE', *, *, #87416, .T. ) ; +#63403 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63404 = VERTEX_POINT ( 'NONE', #68557 ) ; +#63405 = EDGE_CURVE ( 'NONE', #94835, #6289, #84397, .T. ) ; +#63406 = CARTESIAN_POINT ( 'NONE', ( 2.523820061220085176, 3.099999999999960121, 0.000000000000000000 ) ) ; +#63407 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53604 ), #21022 ) ; +#63409 = ORIENTED_EDGE ( 'NONE', *, *, #62435, .T. ) ; +#63408 = CIRCLE ( 'NONE', #94315, 1.874993856093760236 ) ; +#63410 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63411 = ORIENTED_EDGE ( 'NONE', *, *, #16426, .F. ) ; +#63412 = VERTEX_POINT ( 'NONE', #14908 ) ; +#63413 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999689, 0.7099999999999999645, -0.8000000000000001554 ) ) ; +#63414 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#63415 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63416 = VECTOR ( 'NONE', #80593, 1000.000000000000114 ) ; +#63417 = PLANE ( 'NONE', #62913 ) ; +#63418 = SURFACE_STYLE_FILL_AREA ( #1092 ) ; +#63419 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#63420 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#63421 = STYLED_ITEM ( 'NONE', ( #44336 ), #92553 ) ; +#63423 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63422 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.1600000000000000033, 1.250000000000000000 ) ) ; +#63424 = VECTOR ( 'NONE', #96927, 1000.000000000000000 ) ; +#63425 = LINE ( 'NONE', #17902, #62177 ) ; +#63426 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63427 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63428 = ORIENTED_EDGE ( 'NONE', *, *, #53883, .F. ) ; +#63429 = EDGE_CURVE ( 'NONE', #13386, #75277, #86417, .T. ) ; +#63430 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100764 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46375, #14710, #37748 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63431 = FILL_AREA_STYLE ('',( #87883 ) ) ; +#63432 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95946 ) ) ; +#63433 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63434 = ADVANCED_FACE ( 'NONE', ( #79264 ), #94020, .T. ) ; +#63435 = LINE ( 'NONE', #15898, #6721 ) ; +#63436 = SURFACE_STYLE_FILL_AREA ( #39921 ) ; +#63437 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63438 = VECTOR ( 'NONE', #24837, 1000.000000000000000 ) ; +#63439 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63440 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79758 ) ) ; +#63441 = SURFACE_STYLE_USAGE ( .BOTH. , #16910 ) ; +#63442 = AXIS2_PLACEMENT_3D ( 'NONE', #29856, #11583, #61042 ) ; +#63443 = VERTEX_POINT ( 'NONE', #17946 ) ; +#63444 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#63445 = ORIENTED_EDGE ( 'NONE', *, *, #61516, .T. ) ; +#63446 = FILL_AREA_STYLE ('',( #40959 ) ) ; +#63447 = VECTOR ( 'NONE', #33444, 1000.000000000000000 ) ; +#63448 = EDGE_CURVE ( 'NONE', #79973, #93922, #24156, .T. ) ; +#63450 = PRESENTATION_STYLE_ASSIGNMENT (( #24132 ) ) ; +#63449 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63451 = FILL_AREA_STYLE_COLOUR ( '', #40683 ) ; +#63452 = SURFACE_STYLE_USAGE ( .BOTH. , #64433 ) ; +#63453 = AXIS2_PLACEMENT_3D ( 'NONE', #89581, #51793, #89085 ) ; +#63454 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#63455 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96596 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31230, #68993, #7155 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63456 = ORIENTED_EDGE ( 'NONE', *, *, #48880, .T. ) ; +#63457 = LINE ( 'NONE', #47599, #89721 ) ; +#63458 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63459 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.004999999999999959338, -0.1499999999999999944 ) ) ; +#63460 = LINE ( 'NONE', #16411, #47373 ) ; +#63461 = FACE_OUTER_BOUND ( 'NONE', #52280, .T. ) ; +#63462 = SURFACE_STYLE_FILL_AREA ( #69548 ) ; +#63463 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#63464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10216 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23602, #606, #60919 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63465 = SURFACE_STYLE_USAGE ( .BOTH. , #80786 ) ; +#63466 = CARTESIAN_POINT ( 'NONE', ( -0.1054344056808270008, -0.9001170352889870108, 0.8100000000000000533 ) ) ; +#63467 = LINE ( 'NONE', #1134, #76973 ) ; +#63468 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34396, 'distance_accuracy_value', 'NONE'); +#63469 = VECTOR ( 'NONE', #48269, 1000.000000000000000 ) ; +#63470 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#63471 = ORIENTED_EDGE ( 'NONE', *, *, #10628, .F. ) ; +#63472 = SURFACE_STYLE_USAGE ( .BOTH. , #24670 ) ; +#63473 = ORIENTED_EDGE ( 'NONE', *, *, #62186, .F. ) ; +#63474 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#63475 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45900, 'distance_accuracy_value', 'NONE'); +#63476 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48047, 'distance_accuracy_value', 'NONE'); +#63477 = SURFACE_STYLE_USAGE ( .BOTH. , #23637 ) ; +#63478 = PRESENTATION_STYLE_ASSIGNMENT (( #56825 ) ) ; +#63479 = CARTESIAN_POINT ( 'NONE', ( 0.08473270080998969445, -1.389761831846570095, 0.8300000000000004041 ) ) ; +#63480 = LINE ( 'NONE', #16956, #12471 ) ; +#63481 = FILL_AREA_STYLE ('',( #32311 ) ) ; +#63482 = EDGE_LOOP ( 'NONE', ( #92990, #45754, #14343, #35395 ) ) ; +#63483 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#63484 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#63485 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#63486 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88282, 'distance_accuracy_value', 'NONE'); +#63487 = FACE_OUTER_BOUND ( 'NONE', #21428, .T. ) ; +#63488 = VERTEX_POINT ( 'NONE', #2171 ) ; +#63489 = EDGE_LOOP ( 'NONE', ( #4930, #82649, #84959, #3214 ) ) ; +#63490 = LINE ( 'NONE', #81331, #95132 ) ; +#63491 = SURFACE_STYLE_FILL_AREA ( #61475 ) ; +#63492 = SURFACE_SIDE_STYLE ('',( #100617 ) ) ; +#63493 = FILL_AREA_STYLE_COLOUR ( '', #52898 ) ; +#63494 = ORIENTED_EDGE ( 'NONE', *, *, #53679, .T. ) ; +#63495 = COLOUR_RGB ( '',0.2235294117647058654, 0.2235294117647058654, 0.2235294117647058654 ) ; +#63496 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999734, 0.4600000000000000200, -1.250000000000000000 ) ) ; +#63497 = VECTOR ( 'NONE', #3423, 1000.000000000000000 ) ; +#63498 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#63499 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6330 ) ) ; +#63500 = VERTEX_POINT ( 'NONE', #8710 ) ; +#63501 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63502 = CARTESIAN_POINT ( 'NONE', ( 1.723820061220085353, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#63504 = EDGE_CURVE ( 'NONE', #42170, #93963, #72598, .T. ) ; +#63503 = CYLINDRICAL_SURFACE ( 'NONE', #11345, 0.009999999999999998473 ) ; +#63505 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91173 ) ) ; +#63506 = LINE ( 'NONE', #24714, #100857 ) ; +#63507 = ORIENTED_EDGE ( 'NONE', *, *, #96367, .F. ) ; +#63509 = VERTEX_POINT ( 'NONE', #40474 ) ; +#63508 = ORIENTED_EDGE ( 'NONE', *, *, #77978, .F. ) ; +#63510 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#63511 = ORIENTED_EDGE ( 'NONE', *, *, #12736, .F. ) ; +#63512 = EDGE_CURVE ( 'NONE', #89365, #54341, #32297, .T. ) ; +#63513 = CARTESIAN_POINT ( 'NONE', ( 1.799202792133490103, -1.182875588085640306, 0.8299999999999995159 ) ) ; +#63514 = AXIS2_PLACEMENT_3D ( 'NONE', #12639, #21364, #5013 ) ; +#63515 = AXIS2_PLACEMENT_3D ( 'NONE', #73164, #46425, #21575 ) ; +#63516 = VERTEX_POINT ( 'NONE', #79782 ) ; +#63517 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42585, #12352, #80393, #74728 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63519 = ORIENTED_EDGE ( 'NONE', *, *, #53661, .T. ) ; +#63518 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63520 = AXIS2_PLACEMENT_3D ( 'NONE', #28386, #43184, #2904 ) ; +#63521 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63522 = DIRECTION ( 'NONE', ( 2.168404344971010347E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63523 = SURFACE_STYLE_USAGE ( .BOTH. , #16483 ) ; +#63524 = ORIENTED_EDGE ( 'NONE', *, *, #60800, .T. ) ; +#63525 = FILL_AREA_STYLE ('',( #41537 ) ) ; +#63526 = CARTESIAN_POINT ( 'NONE', ( 10.25691912487501334, 3.831700875124988137, 0.8991599999999999593 ) ) ; +#63527 = VERTEX_POINT ( 'NONE', #33311 ) ; +#63528 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999667, -1.504632769052528352E-33 ) ) ; +#63529 = FILL_AREA_STYLE ('',( #73196 ) ) ; +#63530 = SURFACE_STYLE_FILL_AREA ( #78324 ) ; +#63531 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#63532 = ORIENTED_EDGE ( 'NONE', *, *, #70238, .T. ) ; +#63533 = AXIS2_PLACEMENT_3D ( 'NONE', #83268, #82272, #60309 ) ; +#63535 = SURFACE_STYLE_USAGE ( .BOTH. , #71163 ) ; +#63534 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63536 = ORIENTED_EDGE ( 'NONE', *, *, #28853, .F. ) ; +#63537 = FACE_OUTER_BOUND ( 'NONE', #23360, .T. ) ; +#63538 = STYLED_ITEM ( 'NONE', ( #95556 ), #15559 ) ; +#63540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63539 = PRESENTATION_STYLE_ASSIGNMENT (( #48714 ) ) ; +#63541 = FILL_AREA_STYLE_COLOUR ( '', #21323 ) ; +#63542 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63543 = FILL_AREA_STYLE_COLOUR ( '', #53288 ) ; +#63544 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63545 = EDGE_LOOP ( 'NONE', ( #45868, #40365, #52931, #78681 ) ) ; +#63546 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, 3.149999999999979927, 0.000000000000000000 ) ) ; +#63547 = EDGE_CURVE ( 'NONE', #19060, #52561, #64450, .T. ) ; +#63548 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.000000000000000000 ) ) ; +#63549 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63550 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10971, 'distance_accuracy_value', 'NONE'); +#63551 = VECTOR ( 'NONE', #24166, 1000.000000000000000 ) ; +#63552 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63553 = FILL_AREA_STYLE ('',( #93603 ) ) ; +#63554 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63555 = PRESENTATION_STYLE_ASSIGNMENT (( #30856 ) ) ; +#63556 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#63557 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71410, #18260, #16743 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63558 = ORIENTED_EDGE ( 'NONE', *, *, #66854, .T. ) ; +#63561 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#63560 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63559 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, 3.123820061220075051, -0.02000000000000000042 ) ) ; +#63562 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63563 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6398 ) ) ; +#63564 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#63565 = STYLED_ITEM ( 'NONE', ( #12516 ), #85104 ) ; +#63566 = VECTOR ( 'NONE', #1680, 1000.000000000000000 ) ; +#63567 = PRESENTATION_STYLE_ASSIGNMENT (( #1245 ) ) ; +#63568 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#63569 = CIRCLE ( 'NONE', #4848, 0.09999999999999999167 ) ; +#63570 = EDGE_LOOP ( 'NONE', ( #9149, #8379, #93822, #69037 ) ) ; +#63571 = EDGE_CURVE ( 'NONE', #1971, #61021, #8215, .T. ) ; +#63572 = STYLED_ITEM ( 'NONE', ( #30284 ), #6497 ) ; +#63573 = FILL_AREA_STYLE_COLOUR ( '', #41328 ) ; +#63574 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63575 = PRESENTATION_STYLE_ASSIGNMENT (( #32413 ) ) ; +#63576 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63577 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63578 = FILL_AREA_STYLE ('',( #71203 ) ) ; +#63579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19471, #80771, #42466 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63580 = SURFACE_SIDE_STYLE ('',( #8326 ) ) ; +#63581 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63582 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#63583 = ADVANCED_FACE ( 'NONE', ( #1138 ), #80281, .F. ) ; +#63584 = FILL_AREA_STYLE_COLOUR ( '', #25144 ) ; +#63585 = LINE ( 'NONE', #94666, #1078 ) ; +#63586 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999979572, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#63587 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63588 = DIRECTION ( 'NONE', ( 1.668003342285390072E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63589 = LINE ( 'NONE', #55925, #25909 ) ; +#63590 = EDGE_LOOP ( 'NONE', ( #57074, #68765, #53003, #42891 ) ) ; +#63591 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#63592 = VERTEX_POINT ( 'NONE', #66824 ) ; +#63593 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64458, 'distance_accuracy_value', 'NONE'); +#63594 = STYLED_ITEM ( 'NONE', ( #92148 ), #42645 ) ; +#63595 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63596 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8099999999997948841 ) ) ; +#63597 = CARTESIAN_POINT ( 'NONE', ( 0.1930873560432360136, -1.357759925407370227, 0.8100000000000000533 ) ) ; +#63598 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.700000000000000178, 0.000000000000000000 ) ) ; +#63599 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88761, #58159, #18790, #19303 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63600 = CARTESIAN_POINT ( 'NONE', ( -1.268301777710219902, -1.110638925478639960, 0.8100000000000000533 ) ) ; +#63601 = EDGE_CURVE ( 'NONE', #53575, #16593, #44647, .T. ) ; +#63602 = ORIENTED_EDGE ( 'NONE', *, *, #53990, .T. ) ; +#63603 = PLANE ( 'NONE', #69933 ) ; +#63604 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63605 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19271, 'distance_accuracy_value', 'NONE'); +#63606 = SURFACE_STYLE_FILL_AREA ( #72243 ) ; +#63607 = STYLED_ITEM ( 'NONE', ( #3539 ), #51218 ) ; +#63608 = ORIENTED_EDGE ( 'NONE', *, *, #81692, .T. ) ; +#63609 = SURFACE_SIDE_STYLE ('',( #30914 ) ) ; +#63610 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44035 ) ) ; +#63611 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63612 = FACE_OUTER_BOUND ( 'NONE', #94802, .T. ) ; +#63613 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 9.651189000000000462, 0.8648700000000000276 ) ) ; +#63614 = ORIENTED_EDGE ( 'NONE', *, *, #27520, .F. ) ; +#63615 = STYLED_ITEM ( 'NONE', ( #95697 ), #44638 ) ; +#63616 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63617 = ADVANCED_FACE ( 'NONE', ( #83672 ), #75012, .T. ) ; +#63618 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81870, 'distance_accuracy_value', 'NONE'); +#63619 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.299999999999999822, 0.8299999999999999600 ) ) ; +#63620 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#63621 = ORIENTED_EDGE ( 'NONE', *, *, #50225, .T. ) ; +#63622 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63623 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#63624 = VECTOR ( 'NONE', #19990, 1000.000000000000000 ) ; +#63625 = ORIENTED_EDGE ( 'NONE', *, *, #11916, .F. ) ; +#63626 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#63627 = SURFACE_STYLE_USAGE ( .BOTH. , #95711 ) ; +#63628 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#63629 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #63917, #79224, #95012, #54767 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#63630 = EDGE_CURVE ( 'NONE', #37995, #12127, #12123, .T. ) ; +#63631 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74107 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31636, #76583, #47461 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63632 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35935 ) ) ; +#63633 = ORIENTED_EDGE ( 'NONE', *, *, #282, .F. ) ; +#63634 = ORIENTED_EDGE ( 'NONE', *, *, #37577, .T. ) ; +#63635 = LINE ( 'NONE', #94724, #18028 ) ; +#63636 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.1499999999999999667, -3.009265538105054994E-33 ) ) ; +#63637 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63638 = CARTESIAN_POINT ( 'NONE', ( -0.5070681596463531005, -0.9026237492037839649, 0.8299999999999999600 ) ) ; +#63639 = VERTEX_POINT ( 'NONE', #74512 ) ; +#63640 = STYLED_ITEM ( 'NONE', ( #51190 ), #6715 ) ; +#63641 = PRESENTATION_STYLE_ASSIGNMENT (( #24849 ) ) ; +#63642 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63643 = VECTOR ( 'NONE', #86781, 1000.000000000000000 ) ; +#63644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63645 = ORIENTED_EDGE ( 'NONE', *, *, #15931, .T. ) ; +#63647 = LINE ( 'NONE', #94736, #82805 ) ; +#63646 = LINE ( 'NONE', #71795, #14493 ) ; +#63648 = ORIENTED_EDGE ( 'NONE', *, *, #27868, .F. ) ; +#63649 = ORIENTED_EDGE ( 'NONE', *, *, #6565, .F. ) ; +#63650 = FACE_OUTER_BOUND ( 'NONE', #55243, .T. ) ; +#63651 = EDGE_CURVE ( 'NONE', #79876, #69987, #97917, .T. ) ; +#63653 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#63652 = LINE ( 'NONE', #65136, #3909 ) ; +#63654 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59199 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20715, #11458, #67174 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63655 = SURFACE_STYLE_USAGE ( .BOTH. , #78943 ) ; +#63656 = ORIENTED_EDGE ( 'NONE', *, *, #100111, .T. ) ; +#63657 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8770 ), #19611 ) ; +#63659 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63658 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#63660 = SURFACE_SIDE_STYLE ('',( #1348 ) ) ; +#63661 = ORIENTED_EDGE ( 'NONE', *, *, #82692, .F. ) ; +#63662 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63663 = SURFACE_SIDE_STYLE ('',( #49330 ) ) ; +#63664 = ORIENTED_EDGE ( 'NONE', *, *, #4655, .T. ) ; +#63665 = VERTEX_POINT ( 'NONE', #90305 ) ; +#63666 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63667 = EDGE_CURVE ( 'NONE', #69410, #4416, #25180, .T. ) ; +#63668 = FILL_AREA_STYLE_COLOUR ( '', #53902 ) ; +#63669 = PLANE ( 'NONE', #98717 ) ; +#63670 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63671 = LINE ( 'NONE', #38651, #58116 ) ; +#63672 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#63673 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, -1.129999999999999893 ) ) ; +#63675 = LINE ( 'NONE', #48367, #99582 ) ; +#63674 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11383 ), #57195 ) ; +#63676 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#63677 = EDGE_LOOP ( 'NONE', ( #30224, #18632, #42900, #97911 ) ) ; +#63678 = CARTESIAN_POINT ( 'NONE', ( 1.303582274605669999, -1.428972370004099934, 0.8299999999999994049 ) ) ; +#63679 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#63680 = SURFACE_STYLE_USAGE ( .BOTH. , #56024 ) ; +#63681 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63682 = CARTESIAN_POINT ( 'NONE', ( 3.843902000000000374, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#63683 = SURFACE_STYLE_USAGE ( .BOTH. , #1382 ) ; +#63684 = LINE ( 'NONE', #40705, #60834 ) ; +#63685 = ORIENTED_EDGE ( 'NONE', *, *, #92772, .F. ) ; +#63686 = FACE_OUTER_BOUND ( 'NONE', #50961, .T. ) ; +#63687 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63688 = SURFACE_SIDE_STYLE ('',( #869 ) ) ; +#63689 = PRESENTATION_STYLE_ASSIGNMENT (( #63196 ) ) ; +#63690 = FACE_OUTER_BOUND ( 'NONE', #92462, .T. ) ; +#63691 = SURFACE_STYLE_USAGE ( .BOTH. , #80018 ) ; +#63692 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63693 = VECTOR ( 'NONE', #51427, 1000.000000000000000 ) ; +#63694 = DIRECTION ( 'NONE', ( -1.784971879987599845E-14, 1.918759123245459951E-15, -1.000000000000000000 ) ) ; +#63695 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95709, 'distance_accuracy_value', 'NONE'); +#63696 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63697 = EDGE_CURVE ( 'NONE', #13350, #12696, #11210, .T. ) ; +#63698 = EDGE_CURVE ( 'NONE', #10498, #27482, #28052, .T. ) ; +#63699 = SURFACE_SIDE_STYLE ('',( #32553 ) ) ; +#63700 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63701 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76703 ) ) ; +#63703 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999959992 ) ) ; +#63702 = VECTOR ( 'NONE', #29837, 1000.000000000000000 ) ; +#63704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18015 ) ) ; +#63705 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#63706 = SURFACE_STYLE_FILL_AREA ( #71853 ) ; +#63707 = SURFACE_SIDE_STYLE ('',( #49898 ) ) ; +#63708 = SURFACE_SIDE_STYLE ('',( #1907 ) ) ; +#63709 = VECTOR ( 'NONE', #86610, 1000.000000000000000 ) ; +#63710 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52262 ) ) ; +#63711 = CARTESIAN_POINT ( 'NONE', ( 1.850801046367029912, -1.212495751768599916, 0.8100000000000004974 ) ) ; +#63712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63713 = VECTOR ( 'NONE', #45345, 1000.000000000000000 ) ; +#63714 = SURFACE_STYLE_USAGE ( .BOTH. , #35472 ) ; +#63715 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.004999999999999986226, -0.2458578643762690530 ) ) ; +#63716 = EDGE_CURVE ( 'NONE', #42116, #37113, #77586, .T. ) ; +#63717 = ORIENTED_EDGE ( 'NONE', *, *, #89384, .T. ) ; +#63718 = SURFACE_STYLE_USAGE ( .BOTH. , #79015 ) ; +#63719 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63720 = VECTOR ( 'NONE', #38733, 1000.000000000000000 ) ; +#63721 = EDGE_CURVE ( 'NONE', #83336, #9637, #22799, .T. ) ; +#63722 = SURFACE_STYLE_USAGE ( .BOTH. , #46322 ) ; +#63723 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35040, 'distance_accuracy_value', 'NONE'); +#63725 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000000118, 0.2500000000000000000 ) ) ; +#63724 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#63726 = LINE ( 'NONE', #1420, #71011 ) ; +#63727 = DIRECTION ( 'NONE', ( -0.7071067811865485719, -0.7071067811865465735, 0.000000000000000000 ) ) ; +#63728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97901 ), #3365 ) ; +#63729 = EDGE_LOOP ( 'NONE', ( #39230, #38272, #94185, #36145 ) ) ; +#63730 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63731 = STYLED_ITEM ( 'NONE', ( #87605 ), #69212 ) ; +#63732 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63733 = CARTESIAN_POINT ( 'NONE', ( 1.814236996624309928, -1.283680827045210027, 0.8300000000000002931 ) ) ; +#63734 = EDGE_CURVE ( 'NONE', #35208, #100777, #15690, .T. ) ; +#63735 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65451, 'distance_accuracy_value', 'NONE'); +#63736 = FILL_AREA_STYLE_COLOUR ( '', #69120 ) ; +#63737 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1773, 'distance_accuracy_value', 'NONE'); +#63738 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.183333333333333570, 0.000000000000000000 ) ) ; +#63739 = VERTEX_POINT ( 'NONE', #100355 ) ; +#63740 = EDGE_CURVE ( 'NONE', #32845, #6630, #54025, .T. ) ; +#63741 = ORIENTED_EDGE ( 'NONE', *, *, #98404, .T. ) ; +#63742 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63743 = ORIENTED_EDGE ( 'NONE', *, *, #31348, .T. ) ; +#63744 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70255 ) ) ; +#63745 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63746 = LINE ( 'NONE', #41756, #95592 ) ; +#63747 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16447 ), #75182 ) ; +#63748 = EDGE_CURVE ( 'NONE', #9637, #5428, #79957, .T. ) ; +#63749 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #48931 ) ; +#63750 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#63751 = SURFACE_STYLE_FILL_AREA ( #49418 ) ; +#63752 = ADVANCED_FACE ( 'NONE', ( #22365 ), #71354, .F. ) ; +#63754 = VERTEX_POINT ( 'NONE', #34595 ) ; +#63753 = VERTEX_POINT ( 'NONE', #65205 ) ; +#63755 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49026 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82563, #74894, #17857 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63756 = ORIENTED_EDGE ( 'NONE', *, *, #68693, .F. ) ; +#63757 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.05000000000000071, 0.000000000000000000 ) ) ; +#63758 = FILL_AREA_STYLE ('',( #24462 ) ) ; +#63759 = FILL_AREA_STYLE_COLOUR ( '', #24550 ) ; +#63760 = ORIENTED_EDGE ( 'NONE', *, *, #90406, .T. ) ; +#63761 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#63762 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63763 = VECTOR ( 'NONE', #37970, 1000.000000000000114 ) ; +#63764 = EDGE_LOOP ( 'NONE', ( #70244, #16757, #89279, #27982 ) ) ; +#63765 = VERTEX_POINT ( 'NONE', #80549 ) ; +#63766 = ORIENTED_EDGE ( 'NONE', *, *, #26739, .T. ) ; +#63767 = ORIENTED_EDGE ( 'NONE', *, *, #47950, .T. ) ; +#63768 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8299999999999999600 ) ) ; +#63769 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44196 ) ) ; +#63770 = EDGE_CURVE ( 'NONE', #98929, #87432, #2427, .T. ) ; +#63771 = SURFACE_STYLE_FILL_AREA ( #80099 ) ; +#63772 = VECTOR ( 'NONE', #79215, 1000.000000000000000 ) ; +#63773 = ORIENTED_EDGE ( 'NONE', *, *, #98050, .T. ) ; +#63774 = AXIS2_PLACEMENT_3D ( 'NONE', #53675, #29191, #23549 ) ; +#63775 = SURFACE_STYLE_FILL_AREA ( #1482 ) ; +#63776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19738 ) ) ; +#63777 = SURFACE_STYLE_FILL_AREA ( #64762 ) ; +#63778 = VERTEX_POINT ( 'NONE', #2931 ) ; +#63779 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63780 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#63781 = EDGE_LOOP ( 'NONE', ( #38108, #80085, #49925, #59536 ) ) ; +#63782 = ORIENTED_EDGE ( 'NONE', *, *, #75592, .F. ) ; +#63783 = EDGE_CURVE ( 'NONE', #41478, #81114, #57078, .T. ) ; +#63784 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63785 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88265 ), #71939 ) ; +#63786 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#63787 = CARTESIAN_POINT ( 'NONE', ( 0.5238200612200860640, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#63788 = CARTESIAN_POINT ( 'NONE', ( -0.4124892269281669743, -1.212011904613210067, 0.8299999999999999600 ) ) ; +#63789 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13104 ) ) ; +#63790 = EDGE_CURVE ( 'NONE', #95207, #68004, #33585, .T. ) ; +#63791 = SURFACE_STYLE_USAGE ( .BOTH. , #49467 ) ; +#63792 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#63793 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63794 = ORIENTED_EDGE ( 'NONE', *, *, #92685, .F. ) ; +#63795 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63796 = AXIS2_PLACEMENT_3D ( 'NONE', #61102, #52935, #19772 ) ; +#63797 = ORIENTED_EDGE ( 'NONE', *, *, #10166, .F. ) ; +#63798 = EDGE_CURVE ( 'NONE', #79914, #93527, #96818, .T. ) ; +#63799 = VECTOR ( 'NONE', #74557, 1000.000000000000000 ) ; +#63800 = FILL_AREA_STYLE ('',( #56143 ) ) ; +#63801 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63802 = PLANE ( 'NONE', #74530 ) ; +#63803 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63804 = CYLINDRICAL_SURFACE ( 'NONE', #15721, 0.05000000000000012768 ) ; +#63805 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#63806 = CARTESIAN_POINT ( 'NONE', ( 9.252828249749912359, 2.827609249749912568, 0.8991599999999999593 ) ) ; +#63807 = FACE_OUTER_BOUND ( 'NONE', #7483, .T. ) ; +#63808 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63809 = CARTESIAN_POINT ( 'NONE', ( -1.251886425446270046, -0.9762538161110789758, 0.8299999999999998490 ) ) ; +#63810 = AXIS2_PLACEMENT_3D ( 'NONE', #91177, #37576, #5364 ) ; +#63811 = SURFACE_SIDE_STYLE ('',( #56156 ) ) ; +#63812 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#63814 = EDGE_CURVE ( 'NONE', #74161, #28576, #38518, .T. ) ; +#63813 = VECTOR ( 'NONE', #51587, 1000.000000000000114 ) ; +#63815 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54027 ), #24693 ) ; +#63816 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8648700000000000276 ) ) ; +#63817 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63818 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, 0.000000000000000000 ) ) ; +#63819 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93119 ) ) ; +#63820 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63821 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70954, 'distance_accuracy_value', 'NONE'); +#63822 = ORIENTED_EDGE ( 'NONE', *, *, #43481, .T. ) ; +#63823 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63824 = EDGE_CURVE ( 'NONE', #25987, #23167, #41242, .T. ) ; +#63825 = VERTEX_POINT ( 'NONE', #88203 ) ; +#63826 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#63827 = CARTESIAN_POINT ( 'NONE', ( 1.864400774706999941, -0.9907810524907121330, 0.8299999999999999600 ) ) ; +#63828 = EDGE_CURVE ( 'NONE', #28269, #22507, #96319, .T. ) ; +#63829 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#63830 = STYLED_ITEM ( 'NONE', ( #710 ), #18202 ) ; +#63831 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63832 = PLANE ( 'NONE', #76957 ) ; +#63833 = SURFACE_STYLE_FILL_AREA ( #70975 ) ; +#63834 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100931 ) ; +#63835 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#63836 = AXIS2_PLACEMENT_3D ( 'NONE', #19857, #35711, #20354 ) ; +#63837 = ORIENTED_EDGE ( 'NONE', *, *, #25509, .F. ) ; +#63838 = SURFACE_STYLE_USAGE ( .BOTH. , #2045 ) ; +#63839 = VERTEX_POINT ( 'NONE', #26417 ) ; +#63840 = SURFACE_STYLE_USAGE ( .BOTH. , #40356 ) ; +#63841 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70358 ), #86634 ) ; +#63842 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63843 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#63844 = LINE ( 'NONE', #94933, #46620 ) ; +#63845 = AXIS2_PLACEMENT_3D ( 'NONE', #42460, #18433, #57808 ) ; +#63846 = PRESENTATION_STYLE_ASSIGNMENT (( #32697 ) ) ; +#63847 = EDGE_CURVE ( 'NONE', #41410, #31304, #41737, .T. ) ; +#63848 = LINE ( 'NONE', #77635, #69344 ) ; +#63849 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#63850 = ORIENTED_EDGE ( 'NONE', *, *, #58863, .T. ) ; +#63851 = CARTESIAN_POINT ( 'NONE', ( -0.5610005133853442905, 2.432921575926969560, 0.8299999999999999600 ) ) ; +#63852 = PRESENTATION_STYLE_ASSIGNMENT (( #86816 ) ) ; +#63853 = ORIENTED_EDGE ( 'NONE', *, *, #83824, .F. ) ; +#63854 = ADVANCED_FACE ( 'NONE', ( #24934 ), #9499, .T. ) ; +#63855 = FACE_OUTER_BOUND ( 'NONE', #78923, .T. ) ; +#63856 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26326 ) ) ; +#63857 = VECTOR ( 'NONE', #50159, 1000.000000000000000 ) ; +#63858 = ORIENTED_EDGE ( 'NONE', *, *, #60486, .F. ) ; +#63859 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#63860 = PLANE ( 'NONE', #42468 ) ; +#63861 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63862 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#63863 = EDGE_CURVE ( 'NONE', #48290, #43086, #87352, .T. ) ; +#63864 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.000000000000000000, 0.4500000000000000666 ) ) ; +#63865 = EDGE_CURVE ( 'NONE', #5291, #88040, #7787, .T. ) ; +#63867 = ORIENTED_EDGE ( 'NONE', *, *, #35056, .T. ) ; +#63866 = VERTEX_POINT ( 'NONE', #24244 ) ; +#63868 = VECTOR ( 'NONE', #15996, 1000.000000000000000 ) ; +#63869 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63870 = DIRECTION ( 'NONE', ( -0.7071064476869689530, -0.7071071146859689849, 0.000000000000000000 ) ) ; +#63871 = VERTEX_POINT ( 'NONE', #47183 ) ; +#63872 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63873 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.600000000000000089, -11.41999999999999993 ) ) ; +#63874 = VERTEX_POINT ( 'NONE', #63041 ) ; +#63875 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#63876 = ORIENTED_EDGE ( 'NONE', *, *, #99846, .F. ) ; +#63877 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#63878 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#63880 = FILL_AREA_STYLE_COLOUR ( '', #92289 ) ; +#63879 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63881 = ORIENTED_EDGE ( 'NONE', *, *, #73849, .T. ) ; +#63882 = ORIENTED_EDGE ( 'NONE', *, *, #54724, .T. ) ; +#63883 = LINE ( 'NONE', #86854, #73086 ) ; +#63884 = ORIENTED_EDGE ( 'NONE', *, *, #69517, .T. ) ; +#63885 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#63886 = EDGE_CURVE ( 'NONE', #3859, #6634, #215, .T. ) ; +#63888 = ORIENTED_EDGE ( 'NONE', *, *, #33847, .F. ) ; +#63887 = CYLINDRICAL_SURFACE ( 'NONE', #37945, 0.05000000000000002359 ) ; +#63889 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63890 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.000000000000000000 ) ) ; +#63891 = ORIENTED_EDGE ( 'NONE', *, *, #34150, .F. ) ; +#63892 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#63893 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 2.544766999999999779, 0.8648700000000000276 ) ) ; +#63894 = ORIENTED_EDGE ( 'NONE', *, *, #88158, .T. ) ; +#63895 = EDGE_CURVE ( 'NONE', #57258, #28663, #53845, .T. ) ; +#63896 = SURFACE_STYLE_FILL_AREA ( #40929 ) ; +#63897 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#63898 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#63899 = EDGE_CURVE ( 'NONE', #16593, #21886, #78345, .T. ) ; +#63900 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -1.899999999999999911, 0.1829999999999540328 ) ) ; +#63901 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#63902 = FILL_AREA_STYLE ('',( #16375 ) ) ; +#63903 = FACE_OUTER_BOUND ( 'NONE', #90823, .T. ) ; +#63904 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68808 ), #75324 ) ; +#63905 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#63906 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.1250000000000000000 ) ) ; +#63907 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#63908 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#63909 = ORIENTED_EDGE ( 'NONE', *, *, #55026, .T. ) ; +#63910 = EDGE_CURVE ( 'NONE', #96354, #84202, #79830, .T. ) ; +#63911 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50871 ), #18234 ) ; +#63912 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68426 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46148, #54370, #23728 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63913 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63914 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#63915 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63917 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#63916 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#63918 = PRESENTATION_STYLE_ASSIGNMENT (( #49615 ) ) ; +#63919 = VECTOR ( 'NONE', #89385, 1000.000000000000000 ) ; +#63920 = VECTOR ( 'NONE', #67320, 1000.000000000000000 ) ; +#63921 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63922 = EDGE_CURVE ( 'NONE', #97466, #33842, #64031, .T. ) ; +#63923 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#63924 = VERTEX_POINT ( 'NONE', #84971 ) ; +#63925 = CIRCLE ( 'NONE', #18258, 0.009999999999999998473 ) ; +#63926 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#63927 = PLANE ( 'NONE', #2161 ) ; +#63928 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999378, -3.266666666666667052, 0.000000000000000000 ) ) ; +#63929 = STYLED_ITEM ( 'NONE', ( #27741 ), #70167 ) ; +#63930 = FACE_OUTER_BOUND ( 'NONE', #10168, .T. ) ; +#63931 = SURFACE_STYLE_USAGE ( .BOTH. , #82641 ) ; +#63932 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#63933 = AXIS2_PLACEMENT_3D ( 'NONE', #18605, #81941, #50314 ) ; +#63934 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44302, 'distance_accuracy_value', 'NONE'); +#63935 = EDGE_LOOP ( 'NONE', ( #93707, #4606, #12026, #41281 ) ) ; +#63936 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#63937 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#63938 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63939 = EDGE_CURVE ( 'NONE', #58386, #86528, #62034, .T. ) ; +#63940 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#63941 = PRESENTATION_STYLE_ASSIGNMENT (( #33812 ) ) ; +#63942 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#63943 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12246 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40980, #49138, #40469 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63944 = FILL_AREA_STYLE_COLOUR ( '', #13177 ) ; +#63945 = EDGE_CURVE ( 'NONE', #53207, #96275, #35824, .T. ) ; +#63946 = CARTESIAN_POINT ( 'NONE', ( -0.05684101355748980011, -0.9053603395923379704, 0.8299999999999999600 ) ) ; +#63947 = SURFACE_STYLE_USAGE ( .BOTH. , #86928 ) ; +#63948 = SURFACE_SIDE_STYLE ('',( #10212 ) ) ; +#63949 = ORIENTED_EDGE ( 'NONE', *, *, #44568, .F. ) ; +#63950 = PRESENTATION_STYLE_ASSIGNMENT (( #2673 ) ) ; +#63951 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37229 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29925, #92688, #53435 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63952 = VERTEX_POINT ( 'NONE', #31866 ) ; +#63953 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49301 ), #19922 ) ; +#63954 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65123, 'distance_accuracy_value', 'NONE'); +#63955 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#63956 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.3000000000000016542, 7.103537399566374497E-79 ) ) ; +#63957 = PRESENTATION_STYLE_ASSIGNMENT (( #25182 ) ) ; +#63958 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#63959 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#63960 = ORIENTED_EDGE ( 'NONE', *, *, #92676, .T. ) ; +#63961 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, -0.000000000000000000 ) ) ; +#63962 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.000000000000000000 ) ) ; +#63963 = ORIENTED_EDGE ( 'NONE', *, *, #54368, .T. ) ; +#63964 = FILL_AREA_STYLE ('',( #69577 ) ) ; +#63965 = SURFACE_SIDE_STYLE ('',( #41496 ) ) ; +#63966 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#63967 = VERTEX_POINT ( 'NONE', #23721 ) ; +#63968 = STYLED_ITEM ( 'NONE', ( #14099 ), #59991 ) ; +#63969 = VECTOR ( 'NONE', #82380, 1000.000000000000000 ) ; +#63970 = AXIS2_PLACEMENT_3D ( 'NONE', #78607, #23000, #23504 ) ; +#63971 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#63972 = FILL_AREA_STYLE_COLOUR ( '', #20115 ) ; +#63973 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#63974 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#63975 = ORIENTED_EDGE ( 'NONE', *, *, #2205, .F. ) ; +#63976 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45992 ), #32997 ) ; +#63977 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#63978 = EDGE_LOOP ( 'NONE', ( #62533, #8127, #20501, #82149 ) ) ; +#63979 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89985 ), #78679 ) ; +#63980 = EDGE_CURVE ( 'NONE', #72731, #85574, #16023, .T. ) ; +#63981 = CARTESIAN_POINT ( 'NONE', ( 0.4671228747608590082, -1.059049811218969905, 0.8300000000000002931 ) ) ; +#63982 = CIRCLE ( 'NONE', #77011, 0.1000000000000000194 ) ; +#63983 = ORIENTED_EDGE ( 'NONE', *, *, #30356, .F. ) ; +#63984 = FACE_OUTER_BOUND ( 'NONE', #50216, .T. ) ; +#63985 = FILL_AREA_STYLE_COLOUR ( '', #91383 ) ; +#63986 = FILL_AREA_STYLE_COLOUR ( '', #11893 ) ; +#63987 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#63988 = VECTOR ( 'NONE', #60956, 1000.000000000000000 ) ; +#63989 = LINE ( 'NONE', #95089, #30391 ) ; +#63990 = VERTEX_POINT ( 'NONE', #70155 ) ; +#63992 = ORIENTED_EDGE ( 'NONE', *, *, #8623, .T. ) ; +#63991 = EDGE_LOOP ( 'NONE', ( #47384, #22253, #10741, #37532 ) ) ; +#63993 = LINE ( 'NONE', #70114, #87384 ) ; +#63994 = EDGE_LOOP ( 'NONE', ( #96960, #42402, #71405, #13978 ) ) ; +#63995 = SURFACE_STYLE_FILL_AREA ( #6873 ) ; +#63996 = EDGE_CURVE ( 'NONE', #21523, #60190, #15504, .T. ) ; +#63997 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #381 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95494, #25114, #18910 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#63998 = VERTEX_POINT ( 'NONE', #7297 ) ; +#64000 = VERTEX_POINT ( 'NONE', #40039 ) ; +#63999 = PRESENTATION_STYLE_ASSIGNMENT (( #49191 ) ) ; +#64001 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64002 = FILL_AREA_STYLE_COLOUR ( '', #27035 ) ; +#64003 = FACE_OUTER_BOUND ( 'NONE', #61949, .T. ) ; +#64004 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -13.54999999999999893 ) ) ; +#64005 = STYLED_ITEM ( 'NONE', ( #36843 ), #52743 ) ; +#64006 = ORIENTED_EDGE ( 'NONE', *, *, #3888, .T. ) ; +#64007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64008 = ORIENTED_EDGE ( 'NONE', *, *, #34452, .T. ) ; +#64009 = SURFACE_SIDE_STYLE ('',( #24224 ) ) ; +#64010 = STYLED_ITEM ( 'NONE', ( #11085 ), #87568 ) ; +#64011 = FILL_AREA_STYLE_COLOUR ( '', #25535 ) ; +#64012 = VECTOR ( 'NONE', #46837, 1000.000000000000000 ) ; +#64013 = ORIENTED_EDGE ( 'NONE', *, *, #77280, .T. ) ; +#64014 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146561861, 0.3100465759269649957, 0.8100000000000000533 ) ) ; +#64015 = VERTEX_POINT ( 'NONE', #54878 ) ; +#64016 = AXIS2_PLACEMENT_3D ( 'NONE', #6531, #69348, #68855 ) ; +#64017 = CARTESIAN_POINT ( 'NONE', ( -0.008589415658712419230, -1.182875588085640306, 0.8300000000000002931 ) ) ; +#64018 = SURFACE_STYLE_USAGE ( .BOTH. , #1746 ) ; +#64019 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 3.159949000000000119, 0.8991599999999999593 ) ) ; +#64020 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#64021 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29807 ) ) ; +#64022 = EDGE_CURVE ( 'NONE', #28972, #28071, #31360, .T. ) ; +#64023 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51003 ), #18293 ) ; +#64025 = ORIENTED_EDGE ( 'NONE', *, *, #36639, .T. ) ; +#64026 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#64027 = ADVANCED_FACE ( 'NONE', ( #32388 ), #70939, .T. ) ; +#64029 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64028 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#64030 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64031 = LINE ( 'NONE', #30849, #91244 ) ; +#64032 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64033 = VECTOR ( 'NONE', #45040, 1000.000000000000000 ) ; +#64034 = CARTESIAN_POINT ( 'NONE', ( -1.111006624335320048, -0.8869042198941200494, 0.8100000000000000533 ) ) ; +#64035 = EDGE_LOOP ( 'NONE', ( #68610, #67366, #24158, #28345 ) ) ; +#64036 = FACE_BOUND ( 'NONE', #8635, .T. ) ; +#64037 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52605 ) ) ; +#64038 = FILL_AREA_STYLE ('',( #46671 ) ) ; +#64040 = ADVANCED_FACE ( 'NONE', ( #16263 ), #54633, .F. ) ; +#64039 = STYLED_ITEM ( 'NONE', ( #24643 ), #87296 ) ; +#64042 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67228 ) ) ; +#64041 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64043 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64044 = EDGE_CURVE ( 'NONE', #85310, #63260, #53609, .T. ) ; +#64045 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93290 ) ) ; +#64046 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64047 = ORIENTED_EDGE ( 'NONE', *, *, #60103, .F. ) ; +#64048 = CARTESIAN_POINT ( 'NONE', ( -0.9118498257241719473, -1.330101555947649894, 0.8300000000000002931 ) ) ; +#64049 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64051 = FILL_AREA_STYLE_COLOUR ( '', #21598 ) ; +#64050 = FILL_AREA_STYLE ('',( #79363 ) ) ; +#64052 = LINE ( 'NONE', #47712, #27654 ) ; +#64053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99229, 'distance_accuracy_value', 'NONE'); +#64054 = CARTESIAN_POINT ( 'NONE', ( -0.1289016636980840069, -1.445107798742939931, 0.8100000000000000533 ) ) ; +#64055 = EDGE_CURVE ( 'NONE', #27932, #16108, #7542, .T. ) ; +#64056 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37812 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86129, #79506, #40709 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64057 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64058 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64059 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, 0.000000000000000000, 0.1499999999999999944 ) ) ; +#64060 = EDGE_LOOP ( 'NONE', ( #37061, #89811, #11835, #63608 ) ) ; +#64061 = SURFACE_STYLE_USAGE ( .BOTH. , #71712 ) ; +#64062 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999689, -3.266666666666667052, 0.000000000000000000 ) ) ; +#64063 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#64064 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#64065 = ADVANCED_FACE ( 'NONE', ( #78092 ), #16775, .T. ) ; +#64066 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#64067 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#64068 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64069 = PLANE ( 'NONE', #25666 ) ; +#64070 = FILL_AREA_STYLE ('',( #86537 ) ) ; +#64071 = SURFACE_SIDE_STYLE ('',( #48257 ) ) ; +#64072 = ADVANCED_FACE ( 'NONE', ( #100922 ), #31124, .T. ) ; +#64073 = PRESENTATION_STYLE_ASSIGNMENT (( #17073 ) ) ; +#64074 = CARTESIAN_POINT ( 'NONE', ( 1.194650275651319982, -1.445196667902379994, 0.8299999999999999600 ) ) ; +#64075 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#64076 = ORIENTED_EDGE ( 'NONE', *, *, #50911, .F. ) ; +#64077 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#64078 = AXIS2_PLACEMENT_3D ( 'NONE', #73448, #40295, #40796 ) ; +#64079 = ORIENTED_EDGE ( 'NONE', *, *, #6077, .T. ) ; +#64080 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#64081 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#64082 = SURFACE_STYLE_USAGE ( .BOTH. , #32937 ) ; +#64083 = FILL_AREA_STYLE_COLOUR ( '', #96019 ) ; +#64084 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64085 = PLANE ( 'NONE', #76038 ) ; +#64086 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.100000000000000089, -0.02000000000000209943 ) ) ; +#64087 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64088 = VERTEX_POINT ( 'NONE', #17794 ) ; +#64089 = PRESENTATION_STYLE_ASSIGNMENT (( #32943 ) ) ; +#64090 = VECTOR ( 'NONE', #87403, 1000.000000000000114 ) ; +#64091 = ORIENTED_EDGE ( 'NONE', *, *, #35127, .F. ) ; +#64092 = STYLED_ITEM ( 'NONE', ( #40159 ), #47079 ) ; +#64093 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74078 ), #87119 ) ; +#64094 = SURFACE_SIDE_STYLE ('',( #7853 ) ) ; +#64095 = FACE_OUTER_BOUND ( 'NONE', #6646, .T. ) ; +#64096 = SURFACE_SIDE_STYLE ('',( #26819 ) ) ; +#64097 = FACE_OUTER_BOUND ( 'NONE', #40862, .T. ) ; +#64098 = FILL_AREA_STYLE ('',( #32954 ) ) ; +#64099 = ORIENTED_EDGE ( 'NONE', *, *, #62740, .T. ) ; +#64100 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#64101 = SURFACE_SIDE_STYLE ('',( #2328 ) ) ; +#64102 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42277, 'distance_accuracy_value', 'NONE'); +#64103 = FACE_OUTER_BOUND ( 'NONE', #53523, .T. ) ; +#64104 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64105 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80627 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1247, #10842, #9835 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64106 = EDGE_CURVE ( 'NONE', #53420, #35876, #17702, .T. ) ; +#64108 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84972 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63098, #94186, #70209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64107 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.699999999999999956, 0.8299999999999999600 ) ) ; +#64109 = ORIENTED_EDGE ( 'NONE', *, *, #77495, .T. ) ; +#64110 = AXIS2_PLACEMENT_3D ( 'NONE', #9209, #62939, #40451 ) ; +#64111 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88583 ), #6937 ) ; +#64112 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 3.500000000000000444, -1.450207831659080759E-157 ) ) ; +#64113 = PLANE ( 'NONE', #37473 ) ; +#64114 = ORIENTED_EDGE ( 'NONE', *, *, #55257, .F. ) ; +#64115 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64116 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#64117 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64118 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82465 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82732, #66894, #55130 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64119 = VECTOR ( 'NONE', #50674, 1000.000000000000000 ) ; +#64120 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #8403, #20694 ) ; +#64121 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64122 = VECTOR ( 'NONE', #79894, 1000.000000000000114 ) ; +#64123 = ORIENTED_EDGE ( 'NONE', *, *, #67101, .F. ) ; +#64125 = VERTEX_POINT ( 'NONE', #41818 ) ; +#64124 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#64126 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38872, 'distance_accuracy_value', 'NONE'); +#64127 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70660 ), #75554 ) ; +#64128 = SURFACE_SIDE_STYLE ('',( #25346 ) ) ; +#64129 = FILL_AREA_STYLE_COLOUR ( '', #54655 ) ; +#64130 = PRESENTATION_STYLE_ASSIGNMENT (( #32483 ) ) ; +#64131 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4784314575050763185, -0.2458578643762690530 ) ) ; +#64132 = ORIENTED_EDGE ( 'NONE', *, *, #43359, .F. ) ; +#64133 = EDGE_CURVE ( 'NONE', #26939, #48821, #96399, .T. ) ; +#64134 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64135 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64136 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64137 = ORIENTED_EDGE ( 'NONE', *, *, #92693, .F. ) ; +#64138 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36370 ), #46146 ) ; +#64140 = LINE ( 'NONE', #78435, #4511 ) ; +#64139 = FILL_AREA_STYLE_COLOUR ( '', #96004 ) ; +#64141 = VERTEX_POINT ( 'NONE', #87253 ) ; +#64142 = ORIENTED_EDGE ( 'NONE', *, *, #35900, .F. ) ; +#64143 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999990674, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#64144 = LINE ( 'NONE', #86093, #43468 ) ; +#64145 = VECTOR ( 'NONE', #79942, 1000.000000000000000 ) ; +#64146 = SURFACE_STYLE_FILL_AREA ( #24864 ) ; +#64147 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64148 = ORIENTED_EDGE ( 'NONE', *, *, #22991, .T. ) ; +#64149 = SURFACE_SIDE_STYLE ('',( #48343 ) ) ; +#64150 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64151 = ORIENTED_EDGE ( 'NONE', *, *, #19080, .F. ) ; +#64152 = PRESENTATION_STYLE_ASSIGNMENT (( #80996 ) ) ; +#64153 = ORIENTED_EDGE ( 'NONE', *, *, #7807, .F. ) ; +#64154 = ORIENTED_EDGE ( 'NONE', *, *, #70253, .T. ) ; +#64155 = FACE_OUTER_BOUND ( 'NONE', #64766, .T. ) ; +#64157 = FILL_AREA_STYLE_COLOUR ( '', #1739 ) ; +#64156 = PLANE ( 'NONE', #24915 ) ; +#64158 = SURFACE_SIDE_STYLE ('',( #95246 ) ) ; +#64159 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000533, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#64160 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64161 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64162 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64163 = AXIS2_PLACEMENT_3D ( 'NONE', #79288, #54819, #40501 ) ; +#64164 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#64165 = PRESENTATION_STYLE_ASSIGNMENT (( #80001 ) ) ; +#64166 = ORIENTED_EDGE ( 'NONE', *, *, #95118, .F. ) ; +#64167 = CARTESIAN_POINT ( 'NONE', ( 1.278904811106269968, -1.437631519369750199, 0.8299999999999994049 ) ) ; +#64168 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33970 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20958, #91893, #59810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64170 = FILL_AREA_STYLE_COLOUR ( '', #13283 ) ; +#64169 = FILL_AREA_STYLE ('',( #56022 ) ) ; +#64171 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#64172 = EDGE_CURVE ( 'NONE', #69225, #52650, #87765, .T. ) ; +#64173 = STYLED_ITEM ( 'NONE', ( #17081 ), #36354 ) ; +#64174 = FILL_AREA_STYLE_COLOUR ( '', #64819 ) ; +#64175 = SURFACE_SIDE_STYLE ('',( #3881 ) ) ; +#64176 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16823 ), #23424 ) ; +#64177 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.100000000000000089, -0.02000000000002513309 ) ) ; +#64178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64179 = EDGE_LOOP ( 'NONE', ( #87964, #6737, #62657, #81468 ) ) ; +#64180 = PRESENTATION_STYLE_ASSIGNMENT (( #16654 ) ) ; +#64182 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89736, 'distance_accuracy_value', 'NONE'); +#64181 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#64184 = AXIS2_PLACEMENT_3D ( 'NONE', #44008, #75174, #84810 ) ; +#64183 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#64185 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#64186 = AXIS2_PLACEMENT_3D ( 'NONE', #11968, #18689, #58065 ) ; +#64187 = PLANE ( 'NONE', #12121 ) ; +#64188 = LINE ( 'NONE', #26899, #67577 ) ; +#64189 = SURFACE_STYLE_USAGE ( .BOTH. , #46948 ) ; +#64190 = CIRCLE ( 'NONE', #60914, 0.6999999999999999556 ) ; +#64191 = FACE_OUTER_BOUND ( 'NONE', #73916, .T. ) ; +#64192 = STYLED_ITEM ( 'NONE', ( #37714 ), #36906 ) ; +#64193 = EDGE_CURVE ( 'NONE', #97931, #82544, #95389, .T. ) ; +#64194 = STYLED_ITEM ( 'NONE', ( #80689 ), #96859 ) ; +#64195 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64196 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64197 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#64198 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1212, #39520, #2248, #94107 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64199 = PRESENTATION_STYLE_ASSIGNMENT (( #58580 ) ) ; +#64200 = AXIS2_PLACEMENT_3D ( 'NONE', #81901, #11838, #74228 ) ; +#64201 = PRESENTATION_STYLE_ASSIGNMENT (( #23376 ) ) ; +#64202 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64203 = SURFACE_STYLE_FILL_AREA ( #40726 ) ; +#64204 = VERTEX_POINT ( 'NONE', #3518 ) ; +#64205 = SURFACE_STYLE_FILL_AREA ( #40731 ) ; +#64206 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#64208 = LINE ( 'NONE', #75372, #77999 ) ; +#64207 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.5238200612200850648, -0.02000000000000000042 ) ) ; +#64209 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, 0.000000000000000000 ) ) ; +#64210 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#64211 = SURFACE_STYLE_FILL_AREA ( #57588 ) ; +#64212 = EDGE_CURVE ( 'NONE', #12287, #44461, #42814, .T. ) ; +#64213 = EDGE_LOOP ( 'NONE', ( #48265, #70275, #5396, #51966 ) ) ; +#64214 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#64215 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64216 = STYLED_ITEM ( 'NONE', ( #92492 ), #71116 ) ; +#64217 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#64218 = SURFACE_STYLE_USAGE ( .BOTH. , #11001 ) ; +#64219 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64220 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49946 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20014, #44000, #28195 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64221 = EDGE_CURVE ( 'NONE', #97502, #59694, #72950, .T. ) ; +#64222 = SURFACE_SIDE_STYLE ('',( #65736 ) ) ; +#64223 = ORIENTED_EDGE ( 'NONE', *, *, #63922, .T. ) ; +#64224 = ORIENTED_EDGE ( 'NONE', *, *, #97086, .T. ) ; +#64225 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20632 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27770, #42063, #81400 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64226 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#64227 = FILL_AREA_STYLE ('',( #11517 ) ) ; +#64228 = VERTEX_POINT ( 'NONE', #18805 ) ; +#64229 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#64230 = VECTOR ( 'NONE', #134, 1000.000000000000000 ) ; +#64231 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #44262 ) ; +#64232 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#64234 = ORIENTED_EDGE ( 'NONE', *, *, #37195, .T. ) ; +#64233 = VERTEX_POINT ( 'NONE', #50002 ) ; +#64235 = VECTOR ( 'NONE', #56664, 1000.000000000000000 ) ; +#64236 = EDGE_LOOP ( 'NONE', ( #91608, #94861, #47777, #23580 ) ) ; +#64237 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17303, 'distance_accuracy_value', 'NONE'); +#64238 = CARTESIAN_POINT ( 'NONE', ( 1.854034869405480013, -1.451435312150680224, 0.8299999999999999600 ) ) ; +#64240 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64239 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64241 = VERTEX_POINT ( 'NONE', #41327 ) ; +#64242 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13651 ), #67489 ) ; +#64243 = EDGE_CURVE ( 'NONE', #2945, #38264, #80633, .T. ) ; +#64244 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#64245 = STYLED_ITEM ( 'NONE', ( #72036 ), #38166 ) ; +#64246 = VERTEX_POINT ( 'NONE', #17297 ) ; +#64247 = VERTEX_POINT ( 'NONE', #81134 ) ; +#64248 = CARTESIAN_POINT ( 'NONE', ( 1.016666666666667052, -3.099999999999980549, 0.000000000000000000 ) ) ; +#64249 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64250 = ADVANCED_FACE ( 'NONE', ( #48484 ), #9568, .F. ) ; +#64251 = ORIENTED_EDGE ( 'NONE', *, *, #52202, .F. ) ; +#64252 = ORIENTED_EDGE ( 'NONE', *, *, #13691, .T. ) ; +#64253 = SURFACE_SIDE_STYLE ('',( #88252 ) ) ; +#64254 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#64255 = ORIENTED_EDGE ( 'NONE', *, *, #58773, .F. ) ; +#64256 = FILL_AREA_STYLE ('',( #33117 ) ) ; +#64257 = SURFACE_STYLE_USAGE ( .BOTH. , #48463 ) ; +#64258 = AXIS2_PLACEMENT_3D ( 'NONE', #56890, #95120, #18543 ) ; +#64259 = FACE_OUTER_BOUND ( 'NONE', #42912, .T. ) ; +#64260 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#64261 = EDGE_LOOP ( 'NONE', ( #51591, #49520, #57647, #46604 ) ) ; +#64262 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #39351, #69475, #47525, #78660 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64264 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64263 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64265 = VECTOR ( 'NONE', #17379, 1000.000000000000000 ) ; +#64266 = CARTESIAN_POINT ( 'NONE', ( 0.07873568626789680114, -1.258231835375339891, 0.8299999999999999600 ) ) ; +#64267 = VERTEX_POINT ( 'NONE', #42321 ) ; +#64268 = ORIENTED_EDGE ( 'NONE', *, *, #81062, .T. ) ; +#64269 = ADVANCED_FACE ( 'NONE', ( #2508 ), #58171, .T. ) ; +#64271 = SURFACE_STYLE_FILL_AREA ( #79605 ) ; +#64270 = FILL_AREA_STYLE ('',( #18787 ) ) ; +#64272 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64273 = ADVANCED_FACE ( 'NONE', ( #6446 ), #5950, .T. ) ; +#64274 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#64275 = STYLED_ITEM ( 'NONE', ( #15319 ), #67691 ) ; +#64276 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.291173436397889936E-79, 4.640777529015779698E-48 ) ) ; +#64277 = LINE ( 'NONE', #94876, #15006 ) ; +#64278 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#64279 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96055, 'distance_accuracy_value', 'NONE'); +#64280 = ORIENTED_EDGE ( 'NONE', *, *, #40436, .T. ) ; +#64281 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64282 = VERTEX_POINT ( 'NONE', #91755 ) ; +#64283 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64284 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8648700000000000276 ) ) ; +#64286 = EDGE_CURVE ( 'NONE', #82698, #12979, #90785, .T. ) ; +#64285 = CARTESIAN_POINT ( 'NONE', ( 9.125548750250088048, 9.827966249749911398, 0.8991599999999999593 ) ) ; +#64287 = SURFACE_SIDE_STYLE ('',( #6570 ) ) ; +#64288 = VECTOR ( 'NONE', #81210, 1000.000000000000000 ) ; +#64290 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#64289 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64291 = LINE ( 'NONE', #38788, #7536 ) ; +#64292 = SURFACE_STYLE_USAGE ( .BOTH. , #3526 ) ; +#64293 = FACE_OUTER_BOUND ( 'NONE', #55231, .T. ) ; +#64294 = FACE_OUTER_BOUND ( 'NONE', #21549, .T. ) ; +#64295 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7121 ), #70764 ) ; +#64296 = SURFACE_SIDE_STYLE ('',( #62812 ) ) ; +#64297 = LINE ( 'NONE', #50016, #3335 ) ; +#64298 = CARTESIAN_POINT ( 'NONE', ( 1.723820061220085353, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#64299 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64300 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64301 = EDGE_CURVE ( 'NONE', #26704, #19379, #74965, .T. ) ; +#64302 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#64303 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64304 = PRESENTATION_STYLE_ASSIGNMENT (( #41838 ) ) ; +#64305 = VECTOR ( 'NONE', #56661, 1000.000000000000000 ) ; +#64306 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27208, #89477, #11764, #72145 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64307 = VERTEX_POINT ( 'NONE', #66778 ) ; +#64308 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#64309 = CARTESIAN_POINT ( 'NONE', ( 1.531892641499219998, -0.9966931238414048488, 0.8100000000000000533 ) ) ; +#64310 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58370, 'distance_accuracy_value', 'NONE'); +#64311 = ORIENTED_EDGE ( 'NONE', *, *, #46717, .F. ) ; +#64313 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21334, 'distance_accuracy_value', 'NONE'); +#64312 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999902023, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#64314 = FACE_OUTER_BOUND ( 'NONE', #73417, .T. ) ; +#64316 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33357 ), #51292 ) ; +#64315 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54571 ) ) ; +#64317 = LINE ( 'NONE', #7341, #24291 ) ; +#64318 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51293 ) ) ; +#64320 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#64319 = AXIS2_PLACEMENT_3D ( 'NONE', #80879, #4252, #42564 ) ; +#64321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96872 ), #100057 ) ; +#64322 = ADVANCED_FACE ( 'NONE', ( #52997 ), #12085, .T. ) ; +#64323 = VERTEX_POINT ( 'NONE', #61667 ) ; +#64324 = PRESENTATION_STYLE_ASSIGNMENT (( #63838 ) ) ; +#64325 = ORIENTED_EDGE ( 'NONE', *, *, #70804, .T. ) ; +#64326 = PRESENTATION_STYLE_ASSIGNMENT (( #3047 ) ) ; +#64327 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82314, 'distance_accuracy_value', 'NONE'); +#64328 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53612 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40266, #55098, #942 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64329 = DIRECTION ( 'NONE', ( 0.9388213331153586472, 0.000000000000000000, -0.3444045651374278982 ) ) ; +#64330 = LINE ( 'NONE', #25547, #715 ) ; +#64331 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64332 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8991599999999999593 ) ) ; +#64333 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64334 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64335 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64336 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64337 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64338 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#64339 = ORIENTED_EDGE ( 'NONE', *, *, #61196, .T. ) ; +#64340 = EDGE_CURVE ( 'NONE', #37668, #329, #38168, .T. ) ; +#64341 = ORIENTED_EDGE ( 'NONE', *, *, #55020, .F. ) ; +#64342 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#64343 = FILL_AREA_STYLE_COLOUR ( '', #55270 ) ; +#64344 = ORIENTED_EDGE ( 'NONE', *, *, #93932, .T. ) ; +#64345 = FILL_AREA_STYLE_COLOUR ( '', #43034 ) ; +#64346 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67592 ), #21919 ) ; +#64347 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#64348 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64349 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#64350 = CARTESIAN_POINT ( 'NONE', ( -1.153771935001989934, -0.9546485130184679813, 0.8100000000000000533 ) ) ; +#64351 = SURFACE_SIDE_STYLE ('',( #57739 ) ) ; +#64352 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64354 = ORIENTED_EDGE ( 'NONE', *, *, #24531, .F. ) ; +#64353 = ORIENTED_EDGE ( 'NONE', *, *, #39419, .T. ) ; +#64355 = DIRECTION ( 'NONE', ( 0.7071071146859688739, -0.7071064476869688420, 0.000000000000000000 ) ) ; +#64356 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#64357 = ORIENTED_EDGE ( 'NONE', *, *, #44483, .T. ) ; +#64358 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64359 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92078 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23003, #31154, #14772 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64360 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64362 = LINE ( 'NONE', #32730, #56116 ) ; +#64361 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64363 = EDGE_LOOP ( 'NONE', ( #91958, #67093, #55325, #77410 ) ) ; +#64364 = ORIENTED_EDGE ( 'NONE', *, *, #45260, .F. ) ; +#64365 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64366 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#64367 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#64368 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64370 = LINE ( 'NONE', #95480, #100340 ) ; +#64369 = FACE_OUTER_BOUND ( 'NONE', #89122, .T. ) ; +#64371 = CARTESIAN_POINT ( 'NONE', ( -0.03214163119229251214, 0.4502205434146903662, 0.8100000000000000533 ) ) ; +#64372 = ORIENTED_EDGE ( 'NONE', *, *, #25152, .T. ) ; +#64373 = EDGE_LOOP ( 'NONE', ( #68864, #37269, #16427, #24228, #40523, #12632, #5896, #27101, #90050, #35885, #55986, #44118 ) ) ; +#64374 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21613 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95312, #87192, #95825 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64375 = AXIS2_PLACEMENT_3D ( 'NONE', #35415, #2743, #96125 ) ; +#64376 = LINE ( 'NONE', #1596, #56858 ) ; +#64377 = EDGE_CURVE ( 'NONE', #71811, #17472, #24379, .T. ) ; +#64378 = ORIENTED_EDGE ( 'NONE', *, *, #43923, .T. ) ; +#64379 = EDGE_CURVE ( 'NONE', #16993, #55106, #46803, .T. ) ; +#64380 = LINE ( 'NONE', #40405, #10050 ) ; +#64382 = ORIENTED_EDGE ( 'NONE', *, *, #77049, .T. ) ; +#64381 = PLANE ( 'NONE', #93363 ) ; +#64383 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#64384 = VECTOR ( 'NONE', #78472, 1000.000000000000000 ) ; +#64385 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64386 = ORIENTED_EDGE ( 'NONE', *, *, #50254, .F. ) ; +#64388 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#64387 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10480 ) ) ; +#64389 = FACE_OUTER_BOUND ( 'NONE', #42744, .T. ) ; +#64390 = ORIENTED_EDGE ( 'NONE', *, *, #52559, .F. ) ; +#64391 = EDGE_CURVE ( 'NONE', #17982, #71312, #22325, .T. ) ; +#64392 = EDGE_CURVE ( 'NONE', #74534, #21831, #62175, .T. ) ; +#64394 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72542 ), #31730 ) ; +#64393 = CIRCLE ( 'NONE', #75820, 0.1000000000000000194 ) ; +#64395 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #3386, #74331, #65156, #57032 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64396 = STYLED_ITEM ( 'NONE', ( #48251 ), #98818 ) ; +#64397 = FILL_AREA_STYLE_COLOUR ( '', #56776 ) ; +#64398 = EDGE_CURVE ( 'NONE', #7813, #64865, #39665, .T. ) ; +#64399 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#64400 = VECTOR ( 'NONE', #66189, 1000.000000000000000 ) ; +#64401 = FILL_AREA_STYLE ('',( #70530 ) ) ; +#64402 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8991599999999999593 ) ) ; +#64403 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#64404 = ORIENTED_EDGE ( 'NONE', *, *, #11669, .T. ) ; +#64405 = CARTESIAN_POINT ( 'NONE', ( 1.498514669629020135, -1.357596283920579960, 0.8099999999999982769 ) ) ; +#64406 = SURFACE_SIDE_STYLE ('',( #96518 ) ) ; +#64407 = ORIENTED_EDGE ( 'NONE', *, *, #15025, .T. ) ; +#64408 = AXIS2_PLACEMENT_3D ( 'NONE', #62503, #94086, #39002 ) ; +#64409 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64410 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#64413 = ADVANCED_FACE ( 'NONE', ( #37669 ), #85115, .T. ) ; +#64412 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #765 ) ) ; +#64411 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#64414 = FILL_AREA_STYLE ('',( #10173 ) ) ; +#64415 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#64416 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64417 = FILL_AREA_STYLE ('',( #54769 ) ) ; +#64418 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#64419 = EDGE_CURVE ( 'NONE', #31163, #41395, #54510, .T. ) ; +#64420 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95345 ), #54667 ) ; +#64421 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64422 = VECTOR ( 'NONE', #82728, 1000.000000000000000 ) ; +#64423 = SURFACE_STYLE_FILL_AREA ( #31758 ) ; +#64424 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64425 = EDGE_LOOP ( 'NONE', ( #11282, #93549, #46213, #82494, #43639, #90726 ) ) ; +#64426 = ADVANCED_FACE ( 'NONE', ( #16646 ), #15125, .T. ) ; +#64427 = VECTOR ( 'NONE', #98694, 1000.000000000000000 ) ; +#64428 = ADVANCED_FACE ( 'NONE', ( #32534 ), #44015, .T. ) ; +#64429 = STYLED_ITEM ( 'NONE', ( #7125 ), #72082 ) ; +#64430 = FACE_OUTER_BOUND ( 'NONE', #17502, .T. ) ; +#64431 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64432 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#64433 = SURFACE_SIDE_STYLE ('',( #87902 ) ) ; +#64434 = AXIS2_PLACEMENT_3D ( 'NONE', #56539, #11450, #87647 ) ; +#64435 = VERTEX_POINT ( 'NONE', #87645 ) ; +#64436 = SURFACE_STYLE_FILL_AREA ( #58320 ) ; +#64437 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20619 ) ) ; +#64438 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64439 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2494 ) ) ; +#64440 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68589 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46693, #47724, #31900 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64441 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64442 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64443 = CARTESIAN_POINT ( 'NONE', ( -0.9897579360803360204, -1.341449062141889970, 0.8300000000000001821 ) ) ; +#64444 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #4432, #35621 ), + ( #74402, #12016 ), + ( #88703, #58109 ), + ( #42750, #73407 ), + ( #49930, #89219 ), + ( #81079, #13030 ), + ( #11010, #51936 ), + ( #66718, #65223 ), + ( #42261, #3462 ), + ( #34612, #82570 ), + ( #96839, #50450 ), + ( #11520, #98302 ), + ( #43737, #73905 ), + ( #74903, #3935 ), + ( #97818, #89709 ), + ( #19775, #50939 ), + ( #90210, #20254 ), + ( #67223, #28439 ), + ( #59630, #5409 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06972848522764410473, 0.1371566764511970016, 0.2028565572390650107, 0.2668931989899159807, 0.3293761293060860074, 0.3894310858417550092, 0.4479802515295530085, 0.5057883253526750389, 0.5636564595284360157, 0.6208711770372169481, 0.6795632605569840168, 0.7390300992722009799, 0.8005340725457860129, 0.8637937833762510120, 0.9302451451948829941, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64445 = FILL_AREA_STYLE ('',( #41977 ) ) ; +#64446 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11251, 'distance_accuracy_value', 'NONE'); +#64447 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#64448 = EDGE_CURVE ( 'NONE', #14748, #74547, #17668, .T. ) ; +#64449 = AXIS2_PLACEMENT_3D ( 'NONE', #11273, #17984, #80834 ) ; +#64450 = LINE ( 'NONE', #78261, #37417 ) ; +#64451 = EDGE_LOOP ( 'NONE', ( #15482, #23173, #93089, #27491 ) ) ; +#64452 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#64453 = ORIENTED_EDGE ( 'NONE', *, *, #29455, .F. ) ; +#64454 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#64455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62304, 'distance_accuracy_value', 'NONE'); +#64456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88470, 'distance_accuracy_value', 'NONE'); +#64457 = SURFACE_STYLE_USAGE ( .BOTH. , #89442 ) ; +#64458 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64459 = FILL_AREA_STYLE_COLOUR ( '', #62845 ) ; +#64460 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#64461 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64462 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64463 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#64464 = SURFACE_STYLE_FILL_AREA ( #33835 ) ; +#64465 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#64466 = VERTEX_POINT ( 'NONE', #17168 ) ; +#64467 = ADVANCED_FACE ( 'NONE', ( #89157 ), #8940, .T. ) ; +#64468 = SURFACE_STYLE_FILL_AREA ( #94038 ) ; +#64469 = SURFACE_STYLE_USAGE ( .BOTH. , #50185 ) ; +#64470 = ORIENTED_EDGE ( 'NONE', *, *, #20423, .T. ) ; +#64471 = PLANE ( 'NONE', #53314 ) ; +#64472 = ORIENTED_EDGE ( 'NONE', *, *, #10558, .F. ) ; +#64473 = EDGE_CURVE ( 'NONE', #78320, #99343, #3393, .T. ) ; +#64474 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31876 ), #82629 ) ; +#64475 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98493 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67159, #71185, #62044 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64476 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#64477 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64478 = CARTESIAN_POINT ( 'NONE', ( 0.2900000000000000355, -0.01085786437626902814, -0.1500000000000000222 ) ) ; +#64479 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.000000000000000000 ) ) ; +#64480 = EDGE_LOOP ( 'NONE', ( #49079, #31550, #47432, #39014 ) ) ; +#64481 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97092 ), #58032 ) ; +#64482 = FILL_AREA_STYLE_COLOUR ( '', #37606 ) ; +#64483 = SURFACE_STYLE_FILL_AREA ( #73646 ) ; +#64484 = EDGE_LOOP ( 'NONE', ( #74177, #41545, #75747, #11056 ) ) ; +#64485 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36717 ), #20443 ) ; +#64486 = FILL_AREA_STYLE_COLOUR ( '', #94816 ) ; +#64487 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #83428, #29299, #28298, #83919 ), + ( #91566, #20616, #44108, #45080 ), + ( #60958, #76246, #6241, #37474 ), + ( #68576, #99624, #92065, #22126 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606871933, 0.6476030138606871933, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606871933, 0.6476030138606871933, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#64488 = FACE_OUTER_BOUND ( 'NONE', #73886, .T. ) ; +#64489 = ORIENTED_EDGE ( 'NONE', *, *, #8708, .T. ) ; +#64490 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64491 = VECTOR ( 'NONE', #44487, 1000.000000000000000 ) ; +#64492 = SURFACE_STYLE_FILL_AREA ( #73165 ) ; +#64493 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#64494 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#64495 = VERTEX_POINT ( 'NONE', #65667 ) ; +#64498 = ORIENTED_EDGE ( 'NONE', *, *, #66737, .F. ) ; +#64497 = ORIENTED_EDGE ( 'NONE', *, *, #66862, .F. ) ; +#64496 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59651 ) ) ; +#64499 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#64500 = ORIENTED_EDGE ( 'NONE', *, *, #58241, .F. ) ; +#64501 = ADVANCED_FACE ( 'NONE', ( #73837 ), #98237, .T. ) ; +#64502 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64503 = EDGE_LOOP ( 'NONE', ( #41530, #60351, #75047, #11991 ) ) ; +#64504 = ORIENTED_EDGE ( 'NONE', *, *, #57533, .F. ) ; +#64505 = SURFACE_SIDE_STYLE ('',( #57369 ) ) ; +#64506 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67678 ), #93746 ) ; +#64507 = FILL_AREA_STYLE ('',( #56875 ) ) ; +#64508 = ORIENTED_EDGE ( 'NONE', *, *, #59002, .F. ) ; +#64509 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#64510 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64511 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8648700000000000276 ) ) ; +#64512 = ORIENTED_EDGE ( 'NONE', *, *, #4675, .T. ) ; +#64513 = VECTOR ( 'NONE', #76391, 1000.000000000000000 ) ; +#64514 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64515 = AXIS2_PLACEMENT_3D ( 'NONE', #34139, #71916, #73428 ) ; +#64516 = EDGE_CURVE ( 'NONE', #39240, #17269, #19707, .T. ) ; +#64517 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56390 ) ) ; +#64518 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64519 = ORIENTED_EDGE ( 'NONE', *, *, #76870, .T. ) ; +#64521 = CYLINDRICAL_SURFACE ( 'NONE', #30611, 0.04999999999999999584 ) ; +#64520 = STYLED_ITEM ( 'NONE', ( #49448 ), #78455 ) ; +#64522 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64523 = CARTESIAN_POINT ( 'NONE', ( 0.01897074359908140079, -1.165682221622120096, 0.8300000000000002931 ) ) ; +#64525 = LINE ( 'NONE', #18017, #77496 ) ; +#64524 = LINE ( 'NONE', #3236, #18621 ) ; +#64526 = STYLED_ITEM ( 'NONE', ( #97948 ), #77547 ) ; +#64527 = PLANE ( 'NONE', #16268 ) ; +#64528 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77478 ), #93768 ) ; +#64529 = AXIS2_PLACEMENT_3D ( 'NONE', #9746, #143, #94570 ) ; +#64530 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64531 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#64532 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64533 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77747 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94860, #69880, #63286 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64534 = FACE_OUTER_BOUND ( 'NONE', #24456, .T. ) ; +#64535 = VERTEX_POINT ( 'NONE', #91638 ) ; +#64536 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64537 = AXIS2_PLACEMENT_3D ( 'NONE', #31737, #85858, #70022 ) ; +#64538 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#64539 = CARTESIAN_POINT ( 'NONE', ( 11.33879349950005100, 5.832812500499948705, 0.8991599999999999593 ) ) ; +#64540 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#64541 = PRESENTATION_STYLE_ASSIGNMENT (( #4748 ) ) ; +#64542 = STYLED_ITEM ( 'NONE', ( #23060 ), #13548 ) ; +#64543 = ORIENTED_EDGE ( 'NONE', *, *, #96949, .F. ) ; +#64544 = FACE_OUTER_BOUND ( 'NONE', #19170, .T. ) ; +#64545 = ADVANCED_FACE ( 'NONE', ( #98727 ), #97284, .T. ) ; +#64546 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#64547 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#64548 = CARTESIAN_POINT ( 'NONE', ( -0.2389181574176280354, -1.341601374162270099, 0.8100000000000000533 ) ) ; +#64549 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662330114, -1.437662337662340084, 0.8299999999999999600 ) ) ; +#64550 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36785 ), #77585 ) ; +#64551 = FACE_OUTER_BOUND ( 'NONE', #64451, .T. ) ; +#64552 = SURFACE_STYLE_USAGE ( .BOTH. , #26270 ) ; +#64553 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999927350, 0.8500000000000000888, 0.5799137866959191978 ) ) ; +#64554 = EDGE_LOOP ( 'NONE', ( #24600, #65312, #17001, #44344 ) ) ; +#64555 = FILL_AREA_STYLE ('',( #33430 ) ) ; +#64556 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64557 = SURFACE_STYLE_USAGE ( .BOTH. , #237 ) ; +#64558 = FILL_AREA_STYLE_COLOUR ( '', #96982 ) ; +#64559 = SURFACE_STYLE_USAGE ( .BOTH. , #40072 ) ; +#64560 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051948701, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#64561 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64562 = SURFACE_SIDE_STYLE ('',( #42590 ) ) ; +#64563 = VECTOR ( 'NONE', #52724, 1000.000000000000000 ) ; +#64564 = PRESENTATION_STYLE_ASSIGNMENT (( #25777 ) ) ; +#64565 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#64566 = CARTESIAN_POINT ( 'NONE', ( 1.050738163529689961, -1.365949044099890264, 0.8299999999999999600 ) ) ; +#64567 = VECTOR ( 'NONE', #75214, 1000.000000000000000 ) ; +#64568 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64569 = ORIENTED_EDGE ( 'NONE', *, *, #11561, .F. ) ; +#64570 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64571 = ORIENTED_EDGE ( 'NONE', *, *, #53883, .T. ) ; +#64572 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93664, #780, #16579, #39592 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64573 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69282, 'distance_accuracy_value', 'NONE'); +#64574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58081, 'distance_accuracy_value', 'NONE'); +#64575 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64576 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#64577 = CARTESIAN_POINT ( 'NONE', ( 0.2415003227679569930, -1.304818455916720188, 0.8100000000000000533 ) ) ; +#64578 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27059 ) ) ; +#64579 = VECTOR ( 'NONE', #40868, 1000.000000000000114 ) ; +#64580 = SURFACE_STYLE_FILL_AREA ( #95175 ) ; +#64581 = FILL_AREA_STYLE_COLOUR ( '', #98094 ) ; +#64582 = PRESENTATION_STYLE_ASSIGNMENT (( #65575 ) ) ; +#64583 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64584 = VERTEX_POINT ( 'NONE', #21702 ) ; +#64585 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64586 = EDGE_CURVE ( 'NONE', #46497, #3218, #35562, .T. ) ; +#64587 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64588 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64589 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60546, 'distance_accuracy_value', 'NONE'); +#64590 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64591 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95521 ), #27146 ) ; +#64592 = EDGE_LOOP ( 'NONE', ( #92464, #4073, #86172, #89981 ) ) ; +#64593 = SURFACE_SIDE_STYLE ('',( #79418 ) ) ; +#64594 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64595 = EDGE_CURVE ( 'NONE', #91487, #9027, #95631, .T. ) ; +#64596 = VERTEX_POINT ( 'NONE', #27899 ) ; +#64597 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#64598 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71045, 'distance_accuracy_value', 'NONE'); +#64599 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64600 = VECTOR ( 'NONE', #40358, 1000.000000000000000 ) ; +#64601 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64602 = EDGE_CURVE ( 'NONE', #57725, #85932, #59054, .T. ) ; +#64603 = EDGE_LOOP ( 'NONE', ( #2398, #42882, #81812, #86338, #91737, #14091, #47846, #41857, #47913, #29698, #91269 ) ) ; +#64604 = STYLED_ITEM ( 'NONE', ( #85201 ), #39153 ) ; +#64605 = VECTOR ( 'NONE', #40853, 1000.000000000000000 ) ; +#64606 = FACE_OUTER_BOUND ( 'NONE', #31457, .T. ) ; +#64607 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64608 = LINE ( 'NONE', #1312, #19372 ) ; +#64609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#64610 = SURFACE_STYLE_FILL_AREA ( #96226 ) ; +#64611 = VECTOR ( 'NONE', #35221, 1000.000000000000114 ) ; +#64612 = ADVANCED_FACE ( 'NONE', ( #51872 ), #81534, .F. ) ; +#64613 = EDGE_CURVE ( 'NONE', #61356, #1165, #58553, .T. ) ; +#64614 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64615 = ADVANCED_FACE ( 'NONE', ( #20191 ), #21204, .F. ) ; +#64616 = ORIENTED_EDGE ( 'NONE', *, *, #56285, .F. ) ; +#64617 = ADVANCED_FACE ( 'NONE', ( #93616 ), #22211, .F. ) ; +#64618 = VERTEX_POINT ( 'NONE', #53359 ) ; +#64619 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53183 ) ) ; +#64620 = FILL_AREA_STYLE_COLOUR ( '', #60509 ) ; +#64621 = SURFACE_STYLE_USAGE ( .BOTH. , #41152 ) ; +#64622 = FILL_AREA_STYLE_COLOUR ( '', #44746 ) ; +#64623 = PLANE ( 'NONE', #28017 ) ; +#64624 = ORIENTED_EDGE ( 'NONE', *, *, #95017, .T. ) ; +#64625 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#64626 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64627 = ADVANCED_FACE ( 'NONE', ( #23735 ), #8308, .F. ) ; +#64628 = EDGE_LOOP ( 'NONE', ( #22809, #32612, #6635, #54814 ) ) ; +#64630 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#64629 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#64631 = ORIENTED_EDGE ( 'NONE', *, *, #13945, .F. ) ; +#64632 = ORIENTED_EDGE ( 'NONE', *, *, #4455, .T. ) ; +#64633 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64634 = ADVANCED_FACE ( 'NONE', ( #70681, #729 ), #13996, .T. ) ; +#64636 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64635 = PRESENTATION_STYLE_ASSIGNMENT (( #65637 ) ) ; +#64637 = PRESENTATION_STYLE_ASSIGNMENT (( #17142 ) ) ; +#64638 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.350000000000000089, 0.000000000000000000 ) ) ; +#64639 = ORIENTED_EDGE ( 'NONE', *, *, #94985, .T. ) ; +#64640 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64641 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69490 ) ) ; +#64642 = VECTOR ( 'NONE', #723, 1000.000000000000000 ) ; +#64643 = SURFACE_STYLE_USAGE ( .BOTH. , #4358 ) ; +#64644 = ORIENTED_EDGE ( 'NONE', *, *, #25996, .T. ) ; +#64645 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64646 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64647 = ORIENTED_EDGE ( 'NONE', *, *, #54255, .F. ) ; +#64648 = ORIENTED_EDGE ( 'NONE', *, *, #31309, .T. ) ; +#64649 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#64650 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#64651 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64652 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64653 = PRESENTATION_STYLE_ASSIGNMENT (( #2377 ) ) ; +#64654 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87193 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14471, #76797, #85464 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64655 = FILL_AREA_STYLE_COLOUR ( '', #25368 ) ; +#64656 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85850 ) ) ; +#64657 = AXIS2_PLACEMENT_3D ( 'NONE', #38230, #78522, #8494 ) ; +#64658 = CARTESIAN_POINT ( 'NONE', ( -0.09936535710386810993, -1.163903542943879987, 0.8299999999999999600 ) ) ; +#64659 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #13169 ) ; +#64660 = LINE ( 'NONE', #78462, #6203 ) ; +#64661 = VERTEX_POINT ( 'NONE', #96157 ) ; +#64662 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64663 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.300000000000000044, 1.048695503451051965E-76 ) ) ; +#64664 = VECTOR ( 'NONE', #97888, 1000.000000000000114 ) ; +#64665 = EDGE_CURVE ( 'NONE', #100533, #54887, #87172, .T. ) ; +#64666 = SURFACE_STYLE_USAGE ( .BOTH. , #49868 ) ; +#64667 = SURFACE_SIDE_STYLE ('',( #9944 ) ) ; +#64668 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#64669 = VECTOR ( 'NONE', #58191, 1000.000000000000000 ) ; +#64670 = FILL_AREA_STYLE_COLOUR ( '', #82778 ) ; +#64671 = EDGE_CURVE ( 'NONE', #20599, #74684, #41079, .T. ) ; +#64672 = LINE ( 'NONE', #56029, #36973 ) ; +#64673 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#64674 = EDGE_LOOP ( 'NONE', ( #45592, #19257, #7345, #44719 ) ) ; +#64675 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64676 = AXIS2_PLACEMENT_3D ( 'NONE', #7905, #94243, #24357 ) ; +#64677 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64678 = LINE ( 'NONE', #1389, #65980 ) ; +#64679 = FACE_OUTER_BOUND ( 'NONE', #61859, .T. ) ; +#64680 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#64681 = LINE ( 'NONE', #73360, #33360 ) ; +#64682 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65219, 'distance_accuracy_value', 'NONE'); +#64683 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64684 = LINE ( 'NONE', #95789, #6554 ) ; +#64685 = VECTOR ( 'NONE', #1924, 1000.000000000000000 ) ; +#64686 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#64687 = STYLED_ITEM ( 'NONE', ( #59898 ), #14358 ) ; +#64688 = SURFACE_STYLE_USAGE ( .BOTH. , #63707 ) ; +#64689 = VECTOR ( 'NONE', #44038, 1000.000000000000000 ) ; +#64691 = FILL_AREA_STYLE ('',( #33574 ) ) ; +#64690 = VECTOR ( 'NONE', #54956, 1000.000000000000000 ) ; +#64692 = SURFACE_STYLE_FILL_AREA ( #86280 ) ; +#64693 = PRESENTATION_STYLE_ASSIGNMENT (( #39305 ) ) ; +#64694 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96463, 'distance_accuracy_value', 'NONE'); +#64695 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64696 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.4133334038228877461, 0.6665916413350266856 ) ) ; +#64697 = ORIENTED_EDGE ( 'NONE', *, *, #87097, .F. ) ; +#64698 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64699 = EDGE_CURVE ( 'NONE', #53546, #14332, #42072, .T. ) ; +#64700 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#64701 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33713, 'distance_accuracy_value', 'NONE'); +#64702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15631, 'distance_accuracy_value', 'NONE'); +#64703 = STYLED_ITEM ( 'NONE', ( #74895 ), #30598 ) ; +#64705 = PRESENTATION_STYLE_ASSIGNMENT (( #25426 ) ) ; +#64704 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64706 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8991599999999999593 ) ) ; +#64707 = LINE ( 'NONE', #95306, #10089 ) ; +#64708 = ORIENTED_EDGE ( 'NONE', *, *, #69462, .F. ) ; +#64709 = SURFACE_STYLE_USAGE ( .BOTH. , #58596 ) ; +#64710 = PLANE ( 'NONE', #94490 ) ; +#64711 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13020, 'distance_accuracy_value', 'NONE'); +#64713 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2399999999999999634 ) ) ; +#64712 = STYLED_ITEM ( 'NONE', ( #43197 ), #83843 ) ; +#64714 = VECTOR ( 'NONE', #3532, 1000.000000000000000 ) ; +#64715 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76550, 'distance_accuracy_value', 'NONE'); +#64716 = STYLED_ITEM ( 'NONE', ( #21223 ), #55072 ) ; +#64717 = ORIENTED_EDGE ( 'NONE', *, *, #80558, .F. ) ; +#64718 = ORIENTED_EDGE ( 'NONE', *, *, #58659, .T. ) ; +#64719 = PLANE ( 'NONE', #47138 ) ; +#64720 = ORIENTED_EDGE ( 'NONE', *, *, #3537, .T. ) ; +#64721 = LINE ( 'NONE', #39728, #15060 ) ; +#64722 = FACE_OUTER_BOUND ( 'NONE', #69218, .T. ) ; +#64723 = FILL_AREA_STYLE ('',( #71377 ) ) ; +#64724 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990585, 0.000000000000000000 ) ) ; +#64725 = AXIS2_PLACEMENT_3D ( 'NONE', #24838, #64609, #41141 ) ; +#64726 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #94512 ) ; +#64727 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#64728 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64730 = EDGE_LOOP ( 'NONE', ( #88317, #11628, #27853, #18643 ) ) ; +#64729 = EDGE_LOOP ( 'NONE', ( #7613, #36250, #23554, #51205, #3572, #12673 ) ) ; +#64731 = VECTOR ( 'NONE', #58056, 1000.000000000000000 ) ; +#64732 = ORIENTED_EDGE ( 'NONE', *, *, #57403, .F. ) ; +#64733 = ORIENTED_EDGE ( 'NONE', *, *, #55327, .F. ) ; +#64734 = EDGE_CURVE ( 'NONE', #54145, #29713, #44452, .T. ) ; +#64735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64736 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64737 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98403 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70731, #8861, #32949 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64738 = CARTESIAN_POINT ( 'NONE', ( 1.900854206603999952, -1.350767436372750208, 0.8299999999999999600 ) ) ; +#64740 = CARTESIAN_POINT ( 'NONE', ( 1.418698861684009938, -1.069424818316000003, 0.8299999999999999600 ) ) ; +#64739 = CARTESIAN_POINT ( 'NONE', ( 0.5453269378142420187, -1.066140682755960301, 0.8100000000000000533 ) ) ; +#64741 = VERTEX_POINT ( 'NONE', #9827 ) ; +#64743 = VECTOR ( 'NONE', #66784, 1000.000000000000000 ) ; +#64742 = SURFACE_STYLE_USAGE ( .BOTH. , #33102 ) ; +#64744 = FILL_AREA_STYLE ('',( #33623 ) ) ; +#64745 = CIRCLE ( 'NONE', #77785, 0.1000000000000000472 ) ; +#64746 = ORIENTED_EDGE ( 'NONE', *, *, #14398, .F. ) ; +#64747 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#64748 = EDGE_LOOP ( 'NONE', ( #60129, #10843, #72227, #44458 ) ) ; +#64749 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64750 = VECTOR ( 'NONE', #79682, 1000.000000000000000 ) ; +#64751 = ORIENTED_EDGE ( 'NONE', *, *, #69607, .T. ) ; +#64752 = ORIENTED_EDGE ( 'NONE', *, *, #75907, .T. ) ; +#64753 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#64754 = EDGE_CURVE ( 'NONE', #68987, #73420, #10835, .T. ) ; +#64755 = CARTESIAN_POINT ( 'NONE', ( 11.38829012487495618, 7.565224875125044157, 0.8991599999999999593 ) ) ; +#64756 = FILL_AREA_STYLE ('',( #94365 ) ) ; +#64758 = EDGE_LOOP ( 'NONE', ( #97429, #59540, #48808, #96106, #72281, #58432 ) ) ; +#64757 = SURFACE_STYLE_FILL_AREA ( #41298 ) ; +#64759 = LINE ( 'NONE', #25476, #87390 ) ; +#64760 = AXIS2_PLACEMENT_3D ( 'NONE', #9154, #32227, #56235 ) ; +#64761 = EDGE_LOOP ( 'NONE', ( #85676, #15719, #73380, #32104 ) ) ; +#64762 = FILL_AREA_STYLE ('',( #62264 ) ) ; +#64763 = EDGE_LOOP ( 'NONE', ( #24443, #77507, #67353, #1353 ) ) ; +#64764 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -2.700000000000000622, 0.1829999999999460114 ) ) ; +#64765 = SURFACE_STYLE_USAGE ( .BOTH. , #33647 ) ; +#64766 = EDGE_LOOP ( 'NONE', ( #29355, #58426, #68809, #52056 ) ) ; +#64767 = VERTEX_POINT ( 'NONE', #71188 ) ; +#64768 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#64769 = FACE_OUTER_BOUND ( 'NONE', #92124, .T. ) ; +#64770 = FILL_AREA_STYLE ('',( #88267 ) ) ; +#64771 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64703 ) ) ; +#64772 = CARTESIAN_POINT ( 'NONE', ( -0.4373985389610389740, 0.7099999999999999645, -2.710505431213761085E-17 ) ) ; +#64773 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.32344800000000085, 0.8648700000000000276 ) ) ; +#64774 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#64775 = EDGE_CURVE ( 'NONE', #55177, #49438, #49234, .T. ) ; +#64776 = STYLED_ITEM ( 'NONE', ( #58055 ), #30921 ) ; +#64777 = ORIENTED_EDGE ( 'NONE', *, *, #39504, .T. ) ; +#64778 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64779 = ORIENTED_EDGE ( 'NONE', *, *, #42563, .F. ) ; +#64780 = SURFACE_STYLE_USAGE ( .BOTH. , #73468 ) ; +#64781 = SURFACE_SIDE_STYLE ('',( #2510 ) ) ; +#64782 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64783 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66696 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32026, #1391, #16165 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64784 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64785 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#64786 = EDGE_CURVE ( 'NONE', #99206, #299, #9328, .T. ) ; +#64787 = FACE_OUTER_BOUND ( 'NONE', #100921, .T. ) ; +#64788 = SURFACE_STYLE_USAGE ( .BOTH. , #96407 ) ; +#64789 = AXIS2_PLACEMENT_3D ( 'NONE', #85392, #47607, #15423 ) ; +#64790 = LINE ( 'NONE', #70417, #39472 ) ; +#64791 = LINE ( 'NONE', #71453, #24378 ) ; +#64792 = SURFACE_STYLE_FILL_AREA ( #11084 ) ; +#64793 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#64794 = CARTESIAN_POINT ( 'NONE', ( -1.183862409742999944, -0.9551946040733080290, 0.8299999999999998490 ) ) ; +#64795 = LINE ( 'NONE', #18303, #76706 ) ; +#64796 = STYLED_ITEM ( 'NONE', ( #28362 ), #79404 ) ; +#64797 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#64799 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63226 ) ) ; +#64800 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64801 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64802 = SURFACE_STYLE_FILL_AREA ( #18311 ) ; +#64803 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#64804 = AXIS2_PLACEMENT_3D ( 'NONE', #78116, #45409, #7565 ) ; +#64805 = FACE_OUTER_BOUND ( 'NONE', #98065, .T. ) ; +#64806 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333326198, 0.6999999999999999556, 0.000000000000000000 ) ) ; +#64807 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37125 ), #27355 ) ; +#64808 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64809 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95766, 'distance_accuracy_value', 'NONE'); +#64810 = ORIENTED_EDGE ( 'NONE', *, *, #52123, .F. ) ; +#64811 = CLOSED_SHELL ( 'NONE', ( #82729, #90455, #72270, #73384, #75916, #79378 ) ) ; +#64812 = FILL_AREA_STYLE_COLOUR ( '', #39463 ) ; +#64813 = CARTESIAN_POINT ( 'NONE', ( 1.674754468276729913, -0.9004049383407729534, 0.8299999999999999600 ) ) ; +#64814 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64815 = EDGE_LOOP ( 'NONE', ( #10826, #76517, #55330, #92552, #34389, #65469 ) ) ; +#64816 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#64817 = ADVANCED_FACE ( 'NONE', ( #48236 ), #73226, .T. ) ; +#64819 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64818 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#64820 = CARTESIAN_POINT ( 'NONE', ( 1.714851922897540071, -0.9003478538782040408, 0.8299999999999999600 ) ) ; +#64821 = LINE ( 'NONE', #34213, #27484 ) ; +#64822 = PRESENTATION_STYLE_ASSIGNMENT (( #56181 ) ) ; +#64823 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86017 ), #2886 ) ; +#64824 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #49037, #83116, #82894 ), #38739 ) ; +#64825 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#64826 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64827 = SURFACE_SIDE_STYLE ('',( #33702 ) ) ; +#64828 = ORIENTED_EDGE ( 'NONE', *, *, #970, .F. ) ; +#64829 = VERTEX_POINT ( 'NONE', #27775 ) ; +#64830 = FILL_AREA_STYLE_COLOUR ( '', #99204 ) ; +#64831 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#64832 = DIRECTION ( 'NONE', ( -0.9584246665703162193, 0.2853456824793013102, 0.000000000000000000 ) ) ; +#64833 = STYLED_ITEM ( 'NONE', ( #35963 ), #43735 ) ; +#64834 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 9.241066999999999254, 0.8648700000000000276 ) ) ; +#64835 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#64836 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64837 = SURFACE_STYLE_FILL_AREA ( #71494 ) ; +#64838 = VERTEX_POINT ( 'NONE', #81406 ) ; +#64839 = ADVANCED_FACE ( 'NONE', ( #27269 ), #12849, .T. ) ; +#64840 = SURFACE_SIDE_STYLE ('',( #2559 ) ) ; +#64841 = EDGE_CURVE ( 'NONE', #75802, #39313, #50764, .T. ) ; +#64842 = PLANE ( 'NONE', #11784 ) ; +#64843 = ORIENTED_EDGE ( 'NONE', *, *, #73090, .F. ) ; +#64844 = AXIS2_PLACEMENT_3D ( 'NONE', #91954, #45458, #23542 ) ; +#64845 = LINE ( 'NONE', #18861, #53636 ) ; +#64846 = ORIENTED_EDGE ( 'NONE', *, *, #37123, .T. ) ; +#64847 = FILL_AREA_STYLE_COLOUR ( '', #80524 ) ; +#64848 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58401 ) ) ; +#64849 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64850 = CARTESIAN_POINT ( 'NONE', ( 4.515213000000000143, 8.696595000000000297, 0.8648700000000000276 ) ) ; +#64851 = CARTESIAN_POINT ( 'NONE', ( -1.038413249809780003, -1.000241703689469963, 0.8299999999999999600 ) ) ; +#64852 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79654 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51379, #12466, #60551 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64853 = CARTESIAN_POINT ( 'NONE', ( 2.844800000000000217, 10.61720000000000041, 0.8991599999999999593 ) ) ; +#64854 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#64855 = FILL_AREA_STYLE ('',( #73021 ) ) ; +#64856 = PLANE ( 'NONE', #100130 ) ; +#64858 = ORIENTED_EDGE ( 'NONE', *, *, #7348, .F. ) ; +#64857 = ORIENTED_EDGE ( 'NONE', *, *, #77065, .T. ) ; +#64859 = ORIENTED_EDGE ( 'NONE', *, *, #100, .F. ) ; +#64860 = EDGE_CURVE ( 'NONE', #66177, #97203, #90533, .T. ) ; +#64861 = LINE ( 'NONE', #25578, #8453 ) ; +#64862 = VECTOR ( 'NONE', #40732, 1000.000000000000000 ) ; +#64863 = AXIS2_PLACEMENT_3D ( 'NONE', #46168, #84016, #76847 ) ; +#64864 = FILL_AREA_STYLE ('',( #27091 ) ) ; +#64865 = VERTEX_POINT ( 'NONE', #43061 ) ; +#64866 = VERTEX_POINT ( 'NONE', #34932 ) ; +#64867 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64868 = FILL_AREA_STYLE_COLOUR ( '', #68247 ) ; +#64870 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#64869 = PRESENTATION_STYLE_ASSIGNMENT (( #33746 ) ) ; +#64871 = SURFACE_SIDE_STYLE ('',( #17882 ) ) ; +#64872 = ORIENTED_EDGE ( 'NONE', *, *, #34150, .T. ) ; +#64873 = EDGE_LOOP ( 'NONE', ( #47924, #6237, #51691, #93254 ) ) ; +#64874 = ORIENTED_EDGE ( 'NONE', *, *, #48057, .T. ) ; +#64876 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19047, #59422, #76691, #21568 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64875 = SURFACE_STYLE_USAGE ( .BOTH. , #19417 ) ; +#64877 = EDGE_CURVE ( 'NONE', #74099, #81719, #82878, .T. ) ; +#64878 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88213 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31851, #46654, #17018 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64879 = AXIS2_PLACEMENT_3D ( 'NONE', #78489, #100831, #8452 ) ; +#64881 = ORIENTED_EDGE ( 'NONE', *, *, #95363, .T. ) ; +#64880 = FILL_AREA_STYLE_COLOUR ( '', #83655 ) ; +#64882 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42077 ), #35536 ) ; +#64883 = PRESENTATION_STYLE_ASSIGNMENT (( #56756 ) ) ; +#64884 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#64885 = ORIENTED_EDGE ( 'NONE', *, *, #37406, .F. ) ; +#64886 = SURFACE_STYLE_FILL_AREA ( #66395 ) ; +#64887 = CLOSED_SHELL ( 'NONE', ( #4426, #23484, #31296, #60804, #268, #57378 ) ) ; +#64888 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64889 = ORIENTED_EDGE ( 'NONE', *, *, #100750, .T. ) ; +#64890 = AXIS2_PLACEMENT_3D ( 'NONE', #1008, #7060, #32161 ) ; +#64891 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#64892 = CARTESIAN_POINT ( 'NONE', ( 0.2526536197321688215, -1.037435139025664421, 0.8100000000000000533 ) ) ; +#64893 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64894 = ADVANCED_FACE ( 'NONE', ( #44058 ), #96658, .T. ) ; +#64895 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4849999999999999867, -0.2399999999999999911 ) ) ; +#64896 = PRESENTATION_STYLE_ASSIGNMENT (( #80237 ) ) ; +#64898 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#64897 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72117 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31484, #61652, #76719 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64899 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701301354, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#64900 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#64901 = ADVANCED_FACE ( 'NONE', ( #66054 ), #97158, .F. ) ; +#64902 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#64903 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1268 ) ) ; +#64904 = VERTEX_POINT ( 'NONE', #91530 ) ; +#64905 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#64906 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8299999999999999600 ) ) ; +#64907 = ORIENTED_EDGE ( 'NONE', *, *, #57733, .F. ) ; +#64908 = PRESENTATION_STYLE_ASSIGNMENT (( #10686 ) ) ; +#64909 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64910 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49673, #80820, #87946, #25200 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#64911 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#64912 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#64913 = PRESENTATION_STYLE_ASSIGNMENT (( #56275 ) ) ; +#64915 = FILL_AREA_STYLE ('',( #81767 ) ) ; +#64914 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441509868, -1.332102272727269998, 0.8099999999999000222 ) ) ; +#64916 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#64917 = EDGE_CURVE ( 'NONE', #78892, #28211, #46560, .T. ) ; +#64918 = STYLED_ITEM ( 'NONE', ( #16498 ), #75562 ) ; +#64919 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#64920 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #60494, .NOT_KNOWN. ) ; +#64921 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#64922 = FILL_AREA_STYLE ('',( #65936 ) ) ; +#64923 = AXIS2_PLACEMENT_3D ( 'NONE', #87854, #95986, #33243 ) ; +#64924 = FILL_AREA_STYLE_COLOUR ( '', #2353 ) ; +#64925 = ORIENTED_EDGE ( 'NONE', *, *, #90476, .T. ) ; +#64926 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#64927 = FACE_OUTER_BOUND ( 'NONE', #84083, .T. ) ; +#64928 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#64929 = SURFACE_STYLE_USAGE ( .BOTH. , #33805 ) ; +#64930 = CYLINDRICAL_SURFACE ( 'NONE', #60343, 0.05000000000000002359 ) ; +#64931 = AXIS2_PLACEMENT_3D ( 'NONE', #38937, #70568, #62438 ) ; +#64932 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33115, 'distance_accuracy_value', 'NONE'); +#64933 = ORIENTED_EDGE ( 'NONE', *, *, #34346, .T. ) ; +#64934 = STYLED_ITEM ( 'NONE', ( #2926 ), #55595 ) ; +#64935 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#64936 = PLANE ( 'NONE', #23046 ) ; +#64937 = LINE ( 'NONE', #12233, #75946 ) ; +#64938 = LINE ( 'NONE', #17440, #37201 ) ; +#64939 = PLANE ( 'NONE', #36769 ) ; +#64940 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22585 ) ) ; +#64941 = SURFACE_STYLE_FILL_AREA ( #72591 ) ; +#64942 = EDGE_CURVE ( 'NONE', #24285, #78301, #21580, .T. ) ; +#64943 = EDGE_CURVE ( 'NONE', #40001, #94949, #69021, .T. ) ; +#64944 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.100000000000000533, 0.1829999999999500082 ) ) ; +#64945 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17693 ) ) ; +#64946 = CARTESIAN_POINT ( 'NONE', ( 10.66704112487501099, 8.286473124875012530, 0.8991599999999999593 ) ) ; +#64947 = STYLED_ITEM ( 'NONE', ( #19208 ), #62816 ) ; +#64948 = ORIENTED_EDGE ( 'NONE', *, *, #13909, .F. ) ; +#64949 = ORIENTED_EDGE ( 'NONE', *, *, #13058, .T. ) ; +#64950 = STYLED_ITEM ( 'NONE', ( #95763 ), #853 ) ; +#64951 = CYLINDRICAL_SURFACE ( 'NONE', #55239, 0.05000000000000012768 ) ; +#64952 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25827, 'distance_accuracy_value', 'NONE'); +#64953 = SURFACE_SIDE_STYLE ('',( #33829 ) ) ; +#64954 = CARTESIAN_POINT ( 'NONE', ( -0.1988983467373149905, -1.000931601726380071, 0.8299999999999999600 ) ) ; +#64955 = FILL_AREA_STYLE_COLOUR ( '', #24937 ) ; +#64956 = EDGE_CURVE ( 'NONE', #31588, #84851, #13870, .T. ) ; +#64957 = FILL_AREA_STYLE ('',( #73626 ) ) ; +#64958 = PLANE ( 'NONE', #37897 ) ; +#64959 = FILL_AREA_STYLE ('',( #33834 ) ) ; +#64960 = SURFACE_SIDE_STYLE ('',( #10227 ) ) ; +#64961 = CLOSED_SHELL ( 'NONE', ( #14358, #25324, #86053, #75305, #75783, #67091 ) ) ; +#64962 = ORIENTED_EDGE ( 'NONE', *, *, #44416, .T. ) ; +#64963 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#64964 = EDGE_CURVE ( 'NONE', #41637, #30976, #54251, .T. ) ; +#64965 = EDGE_CURVE ( 'NONE', #4908, #39650, #14883, .T. ) ; +#64966 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#64967 = VERTEX_POINT ( 'NONE', #68533 ) ; +#64968 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#64969 = SURFACE_SIDE_STYLE ('',( #11744 ) ) ; +#64970 = ORIENTED_EDGE ( 'NONE', *, *, #96890, .T. ) ; +#64971 = STYLED_ITEM ( 'NONE', ( #72956 ), #50598 ) ; +#64972 = EDGE_CURVE ( 'NONE', #86759, #43302, #99597, .T. ) ; +#64973 = STYLED_ITEM ( 'NONE', ( #21351 ), #15020 ) ; +#64974 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#64975 = LINE ( 'NONE', #87448, #91997 ) ; +#64976 = ORIENTED_EDGE ( 'NONE', *, *, #83299, .F. ) ; +#64977 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#64978 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#64979 = VERTEX_POINT ( 'NONE', #38425 ) ; +#64980 = SURFACE_SIDE_STYLE ('',( #65470 ) ) ; +#64981 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65504, 'distance_accuracy_value', 'NONE'); +#64982 = PRESENTATION_STYLE_ASSIGNMENT (( #88975 ) ) ; +#64983 = ORIENTED_EDGE ( 'NONE', *, *, #66361, .T. ) ; +#64984 = EDGE_CURVE ( 'NONE', #72489, #52805, #22087, .T. ) ; +#64985 = PLANE ( 'NONE', #70936 ) ; +#64986 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#64987 = SURFACE_STYLE_FILL_AREA ( #79304 ) ; +#64988 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64989 = LINE ( 'NONE', #10253, #7916 ) ; +#64990 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90166 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70326, #32562, #8460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#64991 = FILL_AREA_STYLE_COLOUR ( '', #33058 ) ; +#64992 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#64993 = CARTESIAN_POINT ( 'NONE', ( 0.3269029137381110339, -0.9653181426176251634, 0.8299999999999999600 ) ) ; +#64994 = ORIENTED_EDGE ( 'NONE', *, *, #57287, .F. ) ; +#64996 = VERTEX_POINT ( 'NONE', #69535 ) ; +#64995 = ORIENTED_EDGE ( 'NONE', *, *, #88268, .F. ) ; +#64997 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#64998 = ORIENTED_EDGE ( 'NONE', *, *, #83856, .F. ) ; +#64999 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, 0.2850000000000020850, 0.1458578643762672711 ) ) ; +#65000 = EDGE_CURVE ( 'NONE', #65537, #62388, #84375, .T. ) ; +#65001 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65002 = EDGE_CURVE ( 'NONE', #6062, #60878, #102, .T. ) ; +#65003 = ORIENTED_EDGE ( 'NONE', *, *, #96966, .F. ) ; +#65004 = AXIS2_PLACEMENT_3D ( 'NONE', #88353, #18385, #10648 ) ; +#65006 = ORIENTED_EDGE ( 'NONE', *, *, #31246, .F. ) ; +#65005 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65007 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6259 ) ) ; +#65008 = FILL_AREA_STYLE ('',( #33887 ) ) ; +#65009 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65010 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#65011 = VERTEX_POINT ( 'NONE', #15403 ) ; +#65012 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#65013 = SURFACE_SIDE_STYLE ('',( #81372 ) ) ; +#65014 = ORIENTED_EDGE ( 'NONE', *, *, #35788, .F. ) ; +#65015 = PRODUCT_DEFINITION ( 'δ֪', '', #86109, #97309 ) ; +#65016 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17128 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19106, #32942, #34473 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65017 = PRESENTATION_STYLE_ASSIGNMENT (( #33895 ) ) ; +#65018 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15663 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68342, #99401, #61224 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65019 = SURFACE_STYLE_USAGE ( .BOTH. , #25722 ) ; +#65020 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65021 = LINE ( 'NONE', #18013, #65129 ) ; +#65022 = SURFACE_STYLE_USAGE ( .BOTH. , #33902 ) ; +#65023 = VECTOR ( 'NONE', #63784, 1000.000000000000000 ) ; +#65024 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241067000000001030, 0.8991599999999999593 ) ) ; +#65025 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.000000000000000000 ) ) ; +#65026 = ADVANCED_FACE ( 'NONE', ( #14382 ), #78240, .T. ) ; +#65027 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27287, #28283, #20091 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65028 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#65029 = STYLED_ITEM ( 'NONE', ( #67518 ), #1372 ) ; +#65030 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.723820061220085131, -0.02000000000000000042 ) ) ; +#65031 = FILL_AREA_STYLE ('',( #2749 ) ) ; +#65032 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82962 ), #99111 ) ; +#65033 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.05000000000000001665, 0.1900000000000000022 ) ) ; +#65034 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#65036 = EDGE_CURVE ( 'NONE', #11562, #58651, #40961, .T. ) ; +#65035 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14604, #100788, #30974, #62153 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65037 = FACE_OUTER_BOUND ( 'NONE', #22500, .T. ) ; +#65038 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65039 = STYLED_ITEM ( 'NONE', ( #55277 ), #50922 ) ; +#65041 = EDGE_CURVE ( 'NONE', #66816, #7307, #94529, .T. ) ; +#65040 = CARTESIAN_POINT ( 'NONE', ( 0.9820030608313390363, -1.052663393014950044, 0.8100000000000000533 ) ) ; +#65042 = VERTEX_POINT ( 'NONE', #71589 ) ; +#65043 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65044 = CARTESIAN_POINT ( 'NONE', ( 4.425198167651319459, 1.449999999999999956, -11.90937487957755891 ) ) ; +#65045 = STYLED_ITEM ( 'NONE', ( #21235 ), #15203 ) ; +#65046 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#65047 = ORIENTED_EDGE ( 'NONE', *, *, #84525, .T. ) ; +#65048 = CARTESIAN_POINT ( 'NONE', ( -0.9121606455498090238, -1.316410597191429943, 0.8300000000000002931 ) ) ; +#65049 = STYLED_ITEM ( 'NONE', ( #72187 ), #50242 ) ; +#65050 = EDGE_CURVE ( 'NONE', #90959, #42517, #67044, .T. ) ; +#65052 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#65051 = PRESENTATION_STYLE_ASSIGNMENT (( #1772 ) ) ; +#65053 = CARTESIAN_POINT ( 'NONE', ( 1.585655134885600281, -1.389169665048220370, 0.8099999999999976108 ) ) ; +#65054 = FILL_AREA_STYLE ('',( #33931 ) ) ; +#65055 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65056 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#65057 = VERTEX_POINT ( 'NONE', #72088 ) ; +#65058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65059 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65060 = LINE ( 'NONE', #42586, #88208 ) ; +#65061 = FILL_AREA_STYLE_COLOUR ( '', #52592 ) ; +#65062 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#65063 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65064 = VECTOR ( 'NONE', #49270, 1000.000000000000000 ) ; +#65065 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#65066 = SURFACE_SIDE_STYLE ('',( #34453 ) ) ; +#65067 = PRESENTATION_STYLE_ASSIGNMENT (( #98497 ) ) ; +#65068 = ADVANCED_FACE ( 'NONE', ( #64430 ), #95529, .T. ) ; +#65069 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30788, #66709, #59101, #97807 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65070 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31652 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83028, #82536, #44199 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65071 = CARTESIAN_POINT ( 'NONE', ( 1.205759526989409913, -1.445368494507049961, 0.8299999999999999600 ) ) ; +#65072 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65073 = FILL_AREA_STYLE_COLOUR ( '', #7858 ) ; +#65074 = ORIENTED_EDGE ( 'NONE', *, *, #77824, .T. ) ; +#65075 = ORIENTED_EDGE ( 'NONE', *, *, #14370, .F. ) ; +#65076 = AXIS2_PLACEMENT_3D ( 'NONE', #40014, #87987, #48696 ) ; +#65077 = LINE ( 'NONE', #96686, #48813 ) ; +#65078 = FILL_AREA_STYLE_COLOUR ( '', #6995 ) ; +#65079 = CARTESIAN_POINT ( 'NONE', ( 1.864400774706999941, -0.9907810524907121330, 0.8100000000000000533 ) ) ; +#65080 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000466, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#65081 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_L0201_20210301.STEP', ( #27436, #100676 ), #66381 ) ; +#65082 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20878 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65694, #95285, #57562 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65083 = ORIENTED_EDGE ( 'NONE', *, *, #38284, .F. ) ; +#65085 = SURFACE_STYLE_USAGE ( .BOTH. , #2806 ) ; +#65084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1839 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41027, #25696, #17987 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65086 = EDGE_CURVE ( 'NONE', #16380, #7315, #71073, .T. ) ; +#65087 = STYLED_ITEM ( 'NONE', ( #47775 ), #6312 ) ; +#65088 = EDGE_CURVE ( 'NONE', #68343, #83900, #56289, .T. ) ; +#65089 = STYLED_ITEM ( 'NONE', ( #66305 ), #80127 ) ; +#65090 = ORIENTED_EDGE ( 'NONE', *, *, #71167, .F. ) ; +#65091 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65092 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#65093 = AXIS2_PLACEMENT_3D ( 'NONE', #28252, #59432, #95403 ) ; +#65094 = ORIENTED_EDGE ( 'NONE', *, *, #76114, .T. ) ; +#65095 = SURFACE_STYLE_USAGE ( .BOTH. , #67094 ) ; +#65096 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#65097 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89930 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50883, #34569, #11457 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65098 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87984, 'distance_accuracy_value', 'NONE'); +#65099 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65100 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#65101 = AXIS2_PLACEMENT_3D ( 'NONE', #53600, #98952, #100914 ) ; +#65102 = FILL_AREA_STYLE_COLOUR ( '', #61692 ) ; +#65103 = VERTEX_POINT ( 'NONE', #24131 ) ; +#65104 = ADVANCED_FACE ( 'NONE', ( #17430 ), #18440, .T. ) ; +#65105 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65106 = SURFACE_STYLE_USAGE ( .BOTH. , #56485 ) ; +#65107 = SURFACE_SIDE_STYLE ('',( #72776 ) ) ; +#65108 = CARTESIAN_POINT ( 'NONE', ( 4.557639000000000884, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#65109 = STYLED_ITEM ( 'NONE', ( #52135 ), #50951 ) ; +#65110 = FACE_OUTER_BOUND ( 'NONE', #75340, .T. ) ; +#65111 = STYLED_ITEM ( 'NONE', ( #70711 ), #15335 ) ; +#65112 = EDGE_CURVE ( 'NONE', #79876, #18909, #90409, .T. ) ; +#65113 = EDGE_CURVE ( 'NONE', #31335, #32847, #65943, .T. ) ; +#65114 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45523 ) ) ; +#65115 = EDGE_LOOP ( 'NONE', ( #43381, #50695, #27190, #7602 ) ) ; +#65117 = ORIENTED_EDGE ( 'NONE', *, *, #30812, .F. ) ; +#65116 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#65118 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1803, 'distance_accuracy_value', 'NONE'); +#65120 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65119 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8648700000000000276 ) ) ; +#65121 = LINE ( 'NONE', #29814, #61124 ) ; +#65122 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.652400000000000091, 0.8648700000000000276 ) ) ; +#65123 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65124 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#65125 = ORIENTED_EDGE ( 'NONE', *, *, #53525, .F. ) ; +#65126 = FILL_AREA_STYLE_COLOUR ( '', #8141 ) ; +#65127 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65128 = FILL_AREA_STYLE_COLOUR ( '', #82522 ) ; +#65130 = ORIENTED_EDGE ( 'NONE', *, *, #51608, .T. ) ; +#65129 = VECTOR ( 'NONE', #73683, 1000.000000000000000 ) ; +#65131 = SURFACE_STYLE_USAGE ( .BOTH. , #51340 ) ; +#65132 = EDGE_LOOP ( 'NONE', ( #73649, #69869, #38619, #29819 ) ) ; +#65133 = EDGE_LOOP ( 'NONE', ( #68467, #91597, #10746, #61378 ) ) ; +#65134 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24347 ), #12868 ) ; +#65135 = STYLED_ITEM ( 'NONE', ( #70436 ), #32088 ) ; +#65137 = FILL_AREA_STYLE_COLOUR ( '', #41817 ) ; +#65136 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#65138 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65139 = EDGE_CURVE ( 'NONE', #42382, #36882, #4340, .T. ) ; +#65140 = SURFACE_SIDE_STYLE ('',( #89131 ) ) ; +#65141 = EDGE_LOOP ( 'NONE', ( #70130, #58697, #16734, #23847, #63850, #26259 ) ) ; +#65142 = VECTOR ( 'NONE', #32811, 1000.000000000000000 ) ; +#65143 = VERTEX_POINT ( 'NONE', #28145 ) ; +#65144 = CARTESIAN_POINT ( 'NONE', ( 1.314898002023040080, -1.423389424083600030, 0.8100000000000000533 ) ) ; +#65145 = FILL_AREA_STYLE ('',( #34029 ) ) ; +#65146 = ORIENTED_EDGE ( 'NONE', *, *, #63814, .F. ) ; +#65148 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.1900000000000000022 ) ) ; +#65147 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3202 ) ) ; +#65150 = FILL_AREA_STYLE_COLOUR ( '', #9795 ) ; +#65149 = FILL_AREA_STYLE ('',( #31998 ) ) ; +#65151 = CARTESIAN_POINT ( 'NONE', ( -1.297607782917340025, -1.181386160465659918, 0.8299999999999999600 ) ) ; +#65152 = EDGE_CURVE ( 'NONE', #22262, #67581, #73091, .T. ) ; +#65153 = SURFACE_STYLE_USAGE ( .BOTH. , #80487 ) ; +#65154 = EDGE_CURVE ( 'NONE', #44979, #51382, #65409, .T. ) ; +#65155 = CARTESIAN_POINT ( 'NONE', ( -0.05867698335161790346, -1.150470459123589917, 0.8100000000000000533 ) ) ; +#65156 = CARTESIAN_POINT ( 'NONE', ( 1.323820061220085220, -3.099999999999970335, 0.000000000000000000 ) ) ; +#65157 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65158 = CARTESIAN_POINT ( 'NONE', ( 1.314833503436970030, -1.000241703689469963, 0.8100000000000000533 ) ) ; +#65159 = ORIENTED_EDGE ( 'NONE', *, *, #29673, .T. ) ; +#65160 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, -1.050000000000000044 ) ) ; +#65161 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #18831, #74319 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #47899 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#65162 = ADVANCED_FACE ( 'NONE', ( #12225 ), #43443, .F. ) ; +#65164 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65163 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 11.03497999999999912, 0.8648700000000000276 ) ) ; +#65165 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99245, 'distance_accuracy_value', 'NONE'); +#65166 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65167 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65168 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#65169 = EDGE_CURVE ( 'NONE', #19073, #97150, #81286, .T. ) ; +#65170 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#65171 = FILL_AREA_STYLE_COLOUR ( '', #44455 ) ; +#65172 = VERTEX_POINT ( 'NONE', #43945 ) ; +#65173 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65174 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#65175 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65176 = FILL_AREA_STYLE ('',( #41713 ) ) ; +#65177 = FILL_AREA_STYLE ('',( #73853 ) ) ; +#65178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17917 ) ) ; +#65179 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#65181 = EDGE_CURVE ( 'NONE', #98905, #100631, #5111, .T. ) ; +#65180 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65183 = EDGE_CURVE ( 'NONE', #85300, #24413, #7562, .T. ) ; +#65182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61918 ), #17863 ) ; +#65184 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65185 = FILL_AREA_STYLE ('',( #25412 ) ) ; +#65186 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#65187 = FILL_AREA_STYLE_COLOUR ( '', #79539 ) ; +#65188 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#65189 = EDGE_CURVE ( 'NONE', #52805, #47158, #76589, .T. ) ; +#65190 = ADVANCED_FACE ( 'NONE', ( #53627 ), #21969, .T. ) ; +#65191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65192 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#65193 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77073, #52612, #68881, #7534 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65194 = STYLED_ITEM ( 'NONE', ( #94531 ), #29176 ) ; +#65195 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#65196 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -7.819266067965463093E-18, 0.4000000000000000777 ) ) ; +#65197 = ORIENTED_EDGE ( 'NONE', *, *, #75708, .F. ) ; +#65198 = PLANE ( 'NONE', #97555 ) ; +#65199 = PLANE ( 'NONE', #55120 ) ; +#65200 = EDGE_CURVE ( 'NONE', #98956, #73986, #51959, .T. ) ; +#65201 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000172, 0.8991599999999999593 ) ) ; +#65202 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65204 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#65203 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#65205 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#65206 = EDGE_CURVE ( 'NONE', #94369, #67492, #31144, .T. ) ; +#65207 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26096 ) ) ; +#65208 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8648700000000000276 ) ) ; +#65209 = ORIENTED_EDGE ( 'NONE', *, *, #12128, .F. ) ; +#65210 = LINE ( 'NONE', #82560, #40030 ) ; +#65211 = VECTOR ( 'NONE', #50101, 1000.000000000000000 ) ; +#65212 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4749999999999999778, 0.2500000000000001110 ) ) ; +#65213 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91302 ), #22800 ) ; +#65214 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65215 = SURFACE_STYLE_FILL_AREA ( #34110 ) ; +#65216 = VECTOR ( 'NONE', #68088, 1000.000000000000000 ) ; +#65217 = ORIENTED_EDGE ( 'NONE', *, *, #15664, .F. ) ; +#65218 = VERTEX_POINT ( 'NONE', #22473 ) ; +#65219 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65220 = VECTOR ( 'NONE', #6082, 1000.000000000000000 ) ; +#65221 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65222 = ORIENTED_EDGE ( 'NONE', *, *, #12382, .F. ) ; +#65223 = CARTESIAN_POINT ( 'NONE', ( 1.769821822789199972, -1.235192314287260062, 0.8299999999999999600 ) ) ; +#65224 = VECTOR ( 'NONE', #90925, 1000.000000000000000 ) ; +#65225 = SURFACE_SIDE_STYLE ('',( #34118 ) ) ; +#65226 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65227 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #49523 ) ; +#65228 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#65230 = ORIENTED_EDGE ( 'NONE', *, *, #14806, .F. ) ; +#65229 = ORIENTED_EDGE ( 'NONE', *, *, #10013, .F. ) ; +#65231 = ORIENTED_EDGE ( 'NONE', *, *, #39217, .T. ) ; +#65232 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52215 ), #66904 ) ; +#65233 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65234 = VERTEX_POINT ( 'NONE', #93384 ) ; +#65235 = DIRECTION ( 'NONE', ( -0.7071067811865493491, 0.000000000000000000, -0.7071067811865456854 ) ) ; +#65236 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3395, 'distance_accuracy_value', 'NONE'); +#65237 = PLANE ( 'NONE', #60441 ) ; +#65238 = CARTESIAN_POINT ( 'NONE', ( 0.5453269378142420187, -1.066140682755960301, 0.8299999999999999600 ) ) ; +#65239 = ORIENTED_EDGE ( 'NONE', *, *, #5662, .T. ) ; +#65240 = EDGE_CURVE ( 'NONE', #18355, #89625, #23494, .T. ) ; +#65241 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65242 = SURFACE_SIDE_STYLE ('',( #88240 ) ) ; +#65243 = VECTOR ( 'NONE', #84693, 1000.000000000000000 ) ; +#65244 = ORIENTED_EDGE ( 'NONE', *, *, #66389, .T. ) ; +#65245 = SURFACE_SIDE_STYLE ('',( #80591 ) ) ; +#65246 = ORIENTED_EDGE ( 'NONE', *, *, #68957, .F. ) ; +#65247 = FACE_OUTER_BOUND ( 'NONE', #90742, .T. ) ; +#65248 = ORIENTED_EDGE ( 'NONE', *, *, #76343, .F. ) ; +#65249 = EDGE_LOOP ( 'NONE', ( #61387, #53320, #96249, #30576 ) ) ; +#65250 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46957 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25639, #64935, #2156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65251 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65252 = PRESENTATION_STYLE_ASSIGNMENT (( #45488 ) ) ; +#65253 = FILL_AREA_STYLE ('',( #56111 ) ) ; +#65254 = EDGE_CURVE ( 'NONE', #41960, #33631, #6583, .T. ) ; +#65255 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#65256 = ORIENTED_EDGE ( 'NONE', *, *, #16178, .T. ) ; +#65257 = FILL_AREA_STYLE ('',( #86734 ) ) ; +#65258 = VERTEX_POINT ( 'NONE', #62305 ) ; +#65259 = CARTESIAN_POINT ( 'NONE', ( -0.2950099738946450056, -1.071137013546419992, 0.8299999999999999600 ) ) ; +#65260 = ORIENTED_EDGE ( 'NONE', *, *, #54441, .F. ) ; +#65262 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#65261 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051949811, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#65263 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65264 = ORIENTED_EDGE ( 'NONE', *, *, #74588, .T. ) ; +#65265 = VERTEX_POINT ( 'NONE', #13229 ) ; +#65267 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65266 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.000000000000000000 ) ) ; +#65268 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65269 = FACE_OUTER_BOUND ( 'NONE', #70120, .T. ) ; +#65270 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65271 = LINE ( 'NONE', #56650, #24997 ) ; +#65272 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #51904, #14541 ), + ( #60578, #13507 ), + ( #4893, #36088 ), + ( #91674, #45685 ), + ( #98273, #59599 ), + ( #98767, #28899 ), + ( #60092, #17086 ), + ( #46716, #87061 ), + ( #7343, #23773 ), + ( #770, #8344 ), + ( #9366, #31414 ), + ( #86553, #39582 ), + ( #16069, #71226 ), + ( #1800, #269 ), + ( #62087, #54929 ), + ( #70717, #62593 ), + ( #32438, #40607 ), + ( #77876, #55442 ), + ( #31928, #48277 ), + ( #47241, #55936 ), + ( #63090, #93156 ), + ( #15555, #79408 ), + ( #54416, #71739 ), + ( #93653, #7844 ), + ( #63600, #61581 ), + ( #86038, #78391 ), + ( #92655, #16569 ), + ( #85533, #70201 ), + ( #94175, #39083 ), + ( #24297, #22758 ), + ( #47746, #78891 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.04097893070594339771, 0.07886041624184260412, 0.1139485695848140023, 0.1469181589410820110, 0.1789789957062070114, 0.2102877319658280064, 0.2417150887787909985, 0.2734982334250909974, 0.3056144908655740178, 0.3382864838163350263, 0.3715855336697960198, 0.4057812349280769948, 0.4753309549031540238, 0.5451735204053850259, 0.6145171970331100297, 0.6824659191102320221, 0.7153232889272269635, 0.7466521175711750002, 0.7768360883787870375, 0.8055560270855229854, 0.8327754294448449501, 0.8584535229925359667, 0.8825485238002289679, 0.9057267804332469474, 0.9282330950246570067, 0.9509427184471550554, 0.9744340267434640213, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65273 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65274 = VECTOR ( 'NONE', #85087, 1000.000000000000000 ) ; +#65275 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20482, 'distance_accuracy_value', 'NONE'); +#65276 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26163 ) ) ; +#65277 = VERTEX_POINT ( 'NONE', #52634 ) ; +#65278 = VERTEX_POINT ( 'NONE', #77600 ) ; +#65279 = ADVANCED_FACE ( 'NONE', ( #36798 ), #99963, .T. ) ; +#65280 = CARTESIAN_POINT ( 'NONE', ( -0.1833333333333323212, -3.099999999999980549, 0.000000000000000000 ) ) ; +#65282 = LINE ( 'NONE', #56660, #97040 ) ; +#65281 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23304 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45255, #92240, #36656 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65283 = CARTESIAN_POINT ( 'NONE', ( 1.215713331845990064, -1.155903533527329996, 0.8100000000000000533 ) ) ; +#65284 = STYLED_ITEM ( 'NONE', ( #7244 ), #85575 ) ; +#65285 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 2.261924000000000046, 0.8991599999999999593 ) ) ; +#65287 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#65286 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44139 ), #24596 ) ; +#65288 = FACE_OUTER_BOUND ( 'NONE', #86868, .T. ) ; +#65289 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65290 = ADVANCED_FACE ( 'NONE', ( #97298 ), #85750, .F. ) ; +#65291 = LINE ( 'NONE', #3527, #13347 ) ; +#65292 = EDGE_LOOP ( 'NONE', ( #96350, #76256, #94590, #56946 ) ) ; +#65293 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63640 ) ) ; +#65294 = LINE ( 'NONE', #55654, #89588 ) ; +#65295 = SURFACE_STYLE_USAGE ( .BOTH. , #49489 ) ; +#65296 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65297 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14667 ) ) ; +#65298 = EDGE_CURVE ( 'NONE', #91804, #29477, #42220, .T. ) ; +#65299 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#65300 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62045 ), #66972 ) ; +#65301 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#65302 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#65303 = SURFACE_STYLE_USAGE ( .BOTH. , #3026 ) ; +#65304 = LINE ( 'NONE', #81161, #92530 ) ; +#65305 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#65306 = EDGE_CURVE ( 'NONE', #17990, #23798, #34064, .T. ) ; +#65307 = ADVANCED_FACE ( 'NONE', ( #87661 ), #96795, .T. ) ; +#65308 = ORIENTED_EDGE ( 'NONE', *, *, #2855, .T. ) ; +#65309 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, 0.7999999999999999334 ) ) ; +#65310 = PRESENTATION_STYLE_ASSIGNMENT (( #42354 ) ) ; +#65311 = PLANE ( 'NONE', #78596 ) ; +#65312 = ORIENTED_EDGE ( 'NONE', *, *, #95963, .T. ) ; +#65313 = EDGE_CURVE ( 'NONE', #61753, #74773, #64684, .T. ) ; +#65314 = AXIS2_PLACEMENT_3D ( 'NONE', #36076, #3421, #28888 ) ; +#65315 = PLANE ( 'NONE', #81864 ) ; +#65316 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65317 = VECTOR ( 'NONE', #13837, 999.9999999999998863 ) ; +#65318 = ADVANCED_FACE ( 'NONE', ( #57061 ), #50891, .T. ) ; +#65319 = FILL_AREA_STYLE ('',( #34217 ) ) ; +#65320 = ORIENTED_EDGE ( 'NONE', *, *, #12494, .F. ) ; +#65321 = ORIENTED_EDGE ( 'NONE', *, *, #58395, .F. ) ; +#65322 = FACE_OUTER_BOUND ( 'NONE', #24061, .T. ) ; +#65323 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1822, 'distance_accuracy_value', 'NONE'); +#65324 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#65325 = FACE_OUTER_BOUND ( 'NONE', #85428, .T. ) ; +#65326 = FILL_AREA_STYLE_COLOUR ( '', #61316 ) ; +#65327 = LINE ( 'NONE', #96448, #99154 ) ; +#65328 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65329 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220779480, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#65330 = PLANE ( 'NONE', #73957 ) ; +#65331 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65332 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#65333 = ORIENTED_EDGE ( 'NONE', *, *, #44963, .F. ) ; +#65334 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66939 ) ) ; +#65335 = SURFACE_SIDE_STYLE ('',( #74019 ) ) ; +#65336 = VERTEX_POINT ( 'NONE', #20721 ) ; +#65337 = FACE_OUTER_BOUND ( 'NONE', #36605, .T. ) ; +#65338 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65339 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#65340 = CARTESIAN_POINT ( 'NONE', ( -1.349743919808670922, 1.746191508240869439, 0.8099999999999999423 ) ) ; +#65341 = STYLED_ITEM ( 'NONE', ( #54867 ), #86479 ) ; +#65342 = AXIS2_PLACEMENT_3D ( 'NONE', #91133, #75310, #35534 ) ; +#65343 = CIRCLE ( 'NONE', #32716, 0.09999999999999939493 ) ; +#65344 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000000291, 0.000000000000000000 ) ) ; +#65345 = LINE ( 'NONE', #63864, #30115 ) ; +#65347 = ORIENTED_EDGE ( 'NONE', *, *, #93585, .T. ) ; +#65346 = EDGE_LOOP ( 'NONE', ( #6501, #48801, #26351, #94675 ) ) ; +#65348 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65349 = CARTESIAN_POINT ( 'NONE', ( 10.38419850050017423, 3.958979500500174886, 0.8991599999999999593 ) ) ; +#65350 = ORIENTED_EDGE ( 'NONE', *, *, #63383, .T. ) ; +#65351 = VECTOR ( 'NONE', #100192, 1000.000000000000000 ) ; +#65352 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.233333333333333393, 0.000000000000000000 ) ) ; +#65353 = EDGE_LOOP ( 'NONE', ( #50563, #92944, #95139, #45996 ) ) ; +#65354 = EDGE_CURVE ( 'NONE', #44999, #24193, #90152, .T. ) ; +#65355 = VERTEX_POINT ( 'NONE', #90678 ) ; +#65356 = SURFACE_SIDE_STYLE ('',( #34255 ) ) ; +#65357 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65358 = CARTESIAN_POINT ( 'NONE', ( 4.557638875125000766, 6.264148124874999723, 0.8991599999999999593 ) ) ; +#65360 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#65359 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#65361 = SURFACE_SIDE_STYLE ('',( #34261 ) ) ; +#65362 = ORIENTED_EDGE ( 'NONE', *, *, #48745, .T. ) ; +#65363 = VERTEX_POINT ( 'NONE', #60561 ) ; +#65364 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#65365 = EDGE_LOOP ( 'NONE', ( #83065, #44475, #36139, #64746 ) ) ; +#65366 = SURFACE_STYLE_USAGE ( .BOTH. , #82226 ) ; +#65367 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37918, #53735, #62422 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65369 = ORIENTED_EDGE ( 'NONE', *, *, #95131, .T. ) ; +#65368 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65370 = FACE_OUTER_BOUND ( 'NONE', #38393, .T. ) ; +#65371 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#65372 = ORIENTED_EDGE ( 'NONE', *, *, #61487, .F. ) ; +#65373 = ORIENTED_EDGE ( 'NONE', *, *, #33396, .F. ) ; +#65374 = ADVANCED_FACE ( 'NONE', ( #59585 ), #28884, .T. ) ; +#65375 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608730306, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#65376 = FILL_AREA_STYLE ('',( #89380 ) ) ; +#65377 = SURFACE_STYLE_FILL_AREA ( #21813 ) ; +#65378 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65379 = CARTESIAN_POINT ( 'NONE', ( -1.036585239840499995, -1.260670644472420054, 0.8300000000000000711 ) ) ; +#65380 = STYLED_ITEM ( 'NONE', ( #98426 ), #46067 ) ; +#65381 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65382 = SURFACE_STYLE_FILL_AREA ( #67394 ) ; +#65383 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65385 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65384 = LINE ( 'NONE', #96513, #26888 ) ; +#65386 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.299999999999999378, 0.8299999999999999600 ) ) ; +#65387 = EDGE_LOOP ( 'NONE', ( #97111, #56240, #76056, #17740 ) ) ; +#65388 = CARTESIAN_POINT ( 'NONE', ( 1.496184376687780260, -1.336216925617480067, 0.8099999999999982769 ) ) ; +#65389 = CARTESIAN_POINT ( 'NONE', ( -1.132954166604120072, -0.8848558980161149723, 0.8300000000000000711 ) ) ; +#65390 = EDGE_LOOP ( 'NONE', ( #84619, #32494, #59221, #26292 ) ) ; +#65391 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8253 ), #31216 ) ; +#65392 = PLANE ( 'NONE', #55051 ) ; +#65393 = SURFACE_STYLE_FILL_AREA ( #27131 ) ; +#65394 = FACE_OUTER_BOUND ( 'NONE', #27591, .T. ) ; +#65395 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#65396 = SURFACE_SIDE_STYLE ('',( #1632 ) ) ; +#65397 = SURFACE_SIDE_STYLE ('',( #11696 ) ) ; +#65398 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#65399 = CARTESIAN_POINT ( 'NONE', ( 1.797929489527180014, -1.085974092738730024, 0.8100000000000000533 ) ) ; +#65400 = EDGE_CURVE ( 'NONE', #21902, #41891, #13484, .T. ) ; +#65401 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#65402 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65403 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65404 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8648700000000000276 ) ) ; +#65405 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65406 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.300000000000000266, 0.000000000000000000 ) ) ; +#65407 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65408 = ORIENTED_EDGE ( 'NONE', *, *, #93288, .T. ) ; +#65410 = SURFACE_SIDE_STYLE ('',( #18441 ) ) ; +#65409 = LINE ( 'NONE', #96539, #57310 ) ; +#65411 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65412 = STYLED_ITEM ( 'NONE', ( #28939 ), #58708 ) ; +#65413 = CARTESIAN_POINT ( 'NONE', ( 4.953618875124988108, 3.393294875124987175, 0.8648700000000000276 ) ) ; +#65414 = VECTOR ( 'NONE', #11443, 1000.000000000000000 ) ; +#65415 = EDGE_CURVE ( 'NONE', #87078, #57020, #11423, .T. ) ; +#65416 = AXIS2_PLACEMENT_3D ( 'NONE', #36416, #20567, #75220 ) ; +#65417 = VERTEX_POINT ( 'NONE', #82029 ) ; +#65418 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65419 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.399999999999999911, 0.000000000000000000 ) ) ; +#65420 = FACE_OUTER_BOUND ( 'NONE', #77520, .T. ) ; +#65421 = PRESENTATION_STYLE_ASSIGNMENT (( #10717 ) ) ; +#65422 = LINE ( 'NONE', #80781, #93419 ) ; +#65423 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#65424 = LINE ( 'NONE', #96552, #33926 ) ; +#65425 = SURFACE_STYLE_FILL_AREA ( #41470 ) ; +#65426 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68692 ), #89919 ) ; +#65427 = VECTOR ( 'NONE', #52154, 1000.000000000000114 ) ; +#65428 = LINE ( 'NONE', #8841, #35874 ) ; +#65429 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65430 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45455, 'distance_accuracy_value', 'NONE'); +#65431 = EDGE_CURVE ( 'NONE', #91364, #48640, #60251, .T. ) ; +#65432 = LINE ( 'NONE', #88426, #63313 ) ; +#65433 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19601 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39932, #72571, #8689 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65434 = VERTEX_POINT ( 'NONE', #51392 ) ; +#65435 = ORIENTED_EDGE ( 'NONE', *, *, #59640, .F. ) ; +#65436 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#65438 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45677, 'distance_accuracy_value', 'NONE'); +#65437 = STYLED_ITEM ( 'NONE', ( #4828 ), #69996 ) ; +#65439 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32657, 'distance_accuracy_value', 'NONE'); +#65440 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65441 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65442 = FILL_AREA_STYLE_COLOUR ( '', #97039 ) ; +#65443 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65444 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#65445 = SURFACE_SIDE_STYLE ('',( #87931 ) ) ; +#65446 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65447 = FILL_AREA_STYLE ('',( #56830 ) ) ; +#65448 = PRESENTATION_STYLE_ASSIGNMENT (( #96572 ) ) ; +#65449 = ORIENTED_EDGE ( 'NONE', *, *, #22196, .F. ) ; +#65450 = SURFACE_STYLE_USAGE ( .BOTH. , #96069 ) ; +#65451 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65452 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65453 = ORIENTED_EDGE ( 'NONE', *, *, #89401, .T. ) ; +#65454 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65455 = VECTOR ( 'NONE', #82531, 1000.000000000000000 ) ; +#65456 = PRESENTATION_STYLE_ASSIGNMENT (( #81819 ) ) ; +#65457 = ORIENTED_EDGE ( 'NONE', *, *, #48445, .F. ) ; +#65458 = FACE_OUTER_BOUND ( 'NONE', #7909, .T. ) ; +#65459 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65460 = FACE_OUTER_BOUND ( 'NONE', #66016, .T. ) ; +#65461 = EDGE_CURVE ( 'NONE', #20028, #53207, #67179, .T. ) ; +#65462 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65463 = SURFACE_SIDE_STYLE ('',( #34367 ) ) ; +#65464 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#65465 = EDGE_LOOP ( 'NONE', ( #99674, #11271, #77103, #90368, #58728, #34487 ) ) ; +#65466 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52438 ), #78576 ) ; +#65467 = FILL_AREA_STYLE ('',( #66979 ) ) ; +#65468 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#65469 = ORIENTED_EDGE ( 'NONE', *, *, #8761, .F. ) ; +#65470 = SURFACE_STYLE_FILL_AREA ( #34868 ) ; +#65471 = EDGE_CURVE ( 'NONE', #2421, #84311, #85007, .T. ) ; +#65472 = ORIENTED_EDGE ( 'NONE', *, *, #20029, .F. ) ; +#65473 = SURFACE_SIDE_STYLE ('',( #17985 ) ) ; +#65474 = VECTOR ( 'NONE', #86381, 1000.000000000000000 ) ; +#65475 = LINE ( 'NONE', #74166, #43026 ) ; +#65476 = SURFACE_STYLE_USAGE ( .BOTH. , #11277 ) ; +#65477 = CARTESIAN_POINT ( 'NONE', ( 8.231457000000000690, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#65479 = CARTESIAN_POINT ( 'NONE', ( -1.303800513385344084, 1.386221575926970262, 0.8100000000000000533 ) ) ; +#65478 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#65480 = ORIENTED_EDGE ( 'NONE', *, *, #82837, .T. ) ; +#65482 = ORIENTED_EDGE ( 'NONE', *, *, #59062, .F. ) ; +#65481 = EDGE_LOOP ( 'NONE', ( #7180, #9653, #46472, #6042, #32346, #61644, #98099, #92562 ) ) ; +#65483 = SURFACE_STYLE_USAGE ( .BOTH. , #34384 ) ; +#65484 = EDGE_LOOP ( 'NONE', ( #38867, #30064, #45240, #74625 ) ) ; +#65485 = STYLED_ITEM ( 'NONE', ( #30748 ), #95670 ) ; +#65486 = VERTEX_POINT ( 'NONE', #53879 ) ; +#65488 = ORIENTED_EDGE ( 'NONE', *, *, #46785, .T. ) ; +#65487 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000170530, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#65489 = STYLED_ITEM ( 'NONE', ( #34313 ), #8388 ) ; +#65490 = LINE ( 'NONE', #88996, #31247 ) ; +#65491 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#65492 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#65493 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#65494 = ORIENTED_EDGE ( 'NONE', *, *, #40682, .T. ) ; +#65495 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#65496 = SURFACE_STYLE_USAGE ( .BOTH. , #65013 ) ; +#65497 = ORIENTED_EDGE ( 'NONE', *, *, #40864, .T. ) ; +#65498 = SURFACE_SIDE_STYLE ('',( #73193 ) ) ; +#65499 = CARTESIAN_POINT ( 'NONE', ( 0.2850630626479886409, -1.355960596041370536, 0.8100000000000002753 ) ) ; +#65500 = FILL_AREA_STYLE_COLOUR ( '', #92039 ) ; +#65501 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#65502 = ADVANCED_FACE ( 'NONE', ( #55421 ), #24275, .T. ) ; +#65503 = PLANE ( 'NONE', #10073 ) ; +#65504 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65505 = STYLED_ITEM ( 'NONE', ( #96688 ), #25341 ) ; +#65507 = FILL_AREA_STYLE ('',( #88506 ) ) ; +#65506 = PLANE ( 'NONE', #52908 ) ; +#65508 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41060 ), #88338 ) ; +#65509 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38942 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38005, #5809, #29334 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65510 = PLANE ( 'NONE', #97339 ) ; +#65511 = CARTESIAN_POINT ( 'NONE', ( 1.060135477854049935, -1.070174563215090080, 0.8300000000000022915 ) ) ; +#65513 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65512 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#65514 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65515 = LINE ( 'NONE', #96646, #18988 ) ; +#65516 = EDGE_CURVE ( 'NONE', #44288, #67231, #39564, .T. ) ; +#65517 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65518 = ADVANCED_FACE ( 'NONE', ( #92161 ), #14520, .F. ) ; +#65519 = SURFACE_SIDE_STYLE ('',( #3249 ) ) ; +#65520 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65521 = ORIENTED_EDGE ( 'NONE', *, *, #99837, .T. ) ; +#65522 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#65523 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85130 ) ) ; +#65524 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.449999999999999956, -11.90660254037844012 ) ) ; +#65525 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65526 = ORIENTED_EDGE ( 'NONE', *, *, #49719, .T. ) ; +#65527 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#65529 = SURFACE_SIDE_STYLE ('',( #44059 ) ) ; +#65528 = SURFACE_STYLE_USAGE ( .BOTH. , #32901 ) ; +#65530 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54410 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12279, #50201, #49684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65531 = CARTESIAN_POINT ( 'NONE', ( -0.2221370729066020344, -1.389169665048220148, 0.8299999999999999600 ) ) ; +#65532 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65533 = EDGE_CURVE ( 'NONE', #59654, #81638, #93638, .T. ) ; +#65534 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#65535 = SURFACE_STYLE_USAGE ( .BOTH. , #73233 ) ; +#65536 = FILL_AREA_STYLE_COLOUR ( '', #93417 ) ; +#65537 = VERTEX_POINT ( 'NONE', #85514 ) ; +#65538 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65539 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41067, #19049, #50253, #18027 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65540 = LINE ( 'NONE', #10328, #93015 ) ; +#65541 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65542 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.1499999999999999944, 0.08229670385730990245 ) ) ; +#65543 = LINE ( 'NONE', #49767, #89283 ) ; +#65544 = STYLED_ITEM ( 'NONE', ( #94769 ), #18497 ) ; +#65545 = STYLED_ITEM ( 'NONE', ( #43251 ), #34475 ) ; +#65546 = LINE ( 'NONE', #49768, #77838 ) ; +#65547 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#65548 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4699999999999999734, -0.2250000000000000333 ) ) ; +#65549 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65550 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264148000000000494, 0.8648700000000000276 ) ) ; +#65551 = STYLED_ITEM ( 'NONE', ( #73696 ), #87094 ) ; +#65553 = VECTOR ( 'NONE', #38322, 1000.000000000000114 ) ; +#65552 = LINE ( 'NONE', #64565, #42662 ) ; +#65554 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39291, 'distance_accuracy_value', 'NONE'); +#65555 = EDGE_CURVE ( 'NONE', #92506, #10705, #70696, .T. ) ; +#65556 = VECTOR ( 'NONE', #20860, 1000.000000000000000 ) ; +#65557 = LINE ( 'NONE', #11849, #18056 ) ; +#65558 = FACE_OUTER_BOUND ( 'NONE', #12626, .T. ) ; +#65559 = PLANE ( 'NONE', #42123 ) ; +#65560 = PLANE ( 'NONE', #68274 ) ; +#65561 = EDGE_LOOP ( 'NONE', ( #65644, #52080, #70328, #40198 ) ) ; +#65562 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65564 = VERTEX_POINT ( 'NONE', #15539 ) ; +#65563 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78601 ), #96520 ) ; +#65565 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65566 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96351, 'distance_accuracy_value', 'NONE'); +#65567 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10966, 'distance_accuracy_value', 'NONE'); +#65568 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29699 ) ) ; +#65569 = CYLINDRICAL_SURFACE ( 'NONE', #94386, 0.04999999999999991257 ) ; +#65570 = SURFACE_STYLE_FILL_AREA ( #36454 ) ; +#65571 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 10.26637200000000050, 0.8648700000000000276 ) ) ; +#65572 = AXIS2_PLACEMENT_3D ( 'NONE', #86588, #41151, #55982 ) ; +#65573 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99537, #4686, #35875, #98055 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65574 = SURFACE_SIDE_STYLE ('',( #25793 ) ) ; +#65575 = SURFACE_STYLE_USAGE ( .BOTH. , #82428 ) ; +#65576 = FILL_AREA_STYLE_COLOUR ( '', #45472 ) ; +#65577 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65578 = EDGE_LOOP ( 'NONE', ( #49848, #97236, #86853, #36761 ) ) ; +#65579 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65580 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65581 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21525, 'distance_accuracy_value', 'NONE'); +#65582 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70447 ) ) ; +#65583 = ORIENTED_EDGE ( 'NONE', *, *, #37524, .F. ) ; +#65584 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65585 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#65586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65587 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65588 = ADVANCED_FACE ( 'NONE', ( #245 ), #94157, .T. ) ; +#65589 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#65591 = ORIENTED_EDGE ( 'NONE', *, *, #53164, .F. ) ; +#65590 = AXIS2_PLACEMENT_3D ( 'NONE', #97612, #36385, #67989 ) ; +#65592 = SURFACE_STYLE_FILL_AREA ( #41629 ) ; +#65593 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66439, 'distance_accuracy_value', 'NONE'); +#65594 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65595 = CARTESIAN_POINT ( 'NONE', ( -1.076179938779914913, -3.099999999999990319, -0.02000000000000000042 ) ) ; +#65596 = VECTOR ( 'NONE', #33331, 1000.000000000000000 ) ; +#65597 = LINE ( 'NONE', #64107, #15796 ) ; +#65598 = EDGE_CURVE ( 'NONE', #4894, #39103, #81424, .T. ) ; +#65599 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #22336, #46814, #76971, #69259 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65600 = ORIENTED_EDGE ( 'NONE', *, *, #42961, .T. ) ; +#65601 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65602 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65603 = STYLED_ITEM ( 'NONE', ( #62057 ), #87665 ) ; +#65604 = PRESENTATION_STYLE_ASSIGNMENT (( #80964 ) ) ; +#65606 = FILL_AREA_STYLE_COLOUR ( '', #51082 ) ; +#65605 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3655 ) ) ; +#65607 = CARTESIAN_POINT ( 'NONE', ( -1.045783160910370935, -1.254699690856918570, 0.8099999999998004352 ) ) ; +#65608 = EDGE_CURVE ( 'NONE', #67839, #60860, #56437, .T. ) ; +#65609 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65610 = AXIS2_PLACEMENT_3D ( 'NONE', #95354, #80097, #65773 ) ; +#65611 = ADVANCED_FACE ( 'NONE', ( #25290 ), #9844, .T. ) ; +#65612 = AXIS2_PLACEMENT_3D ( 'NONE', #18880, #57234, #18372 ) ; +#65613 = ORIENTED_EDGE ( 'NONE', *, *, #37076, .F. ) ; +#65615 = VERTEX_POINT ( 'NONE', #50287 ) ; +#65614 = SURFACE_STYLE_USAGE ( .BOTH. , #3340 ) ; +#65617 = FILL_AREA_STYLE_COLOUR ( '', #80752 ) ; +#65616 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65618 = STYLED_ITEM ( 'NONE', ( #10848 ), #35390 ) ; +#65619 = FILL_AREA_STYLE ('',( #20657 ) ) ; +#65620 = SURFACE_SIDE_STYLE ('',( #27339 ) ) ; +#65621 = ORIENTED_EDGE ( 'NONE', *, *, #78177, .T. ) ; +#65622 = CARTESIAN_POINT ( 'NONE', ( 1.364996439099779968, -1.475119686261340046, 0.8299999999999999600 ) ) ; +#65623 = PRESENTATION_STYLE_ASSIGNMENT (( #76671 ) ) ; +#65624 = FACE_OUTER_BOUND ( 'NONE', #22940, .T. ) ; +#65625 = STYLED_ITEM ( 'NONE', ( #9130 ), #37222 ) ; +#65626 = AXIS2_PLACEMENT_3D ( 'NONE', #53861, #38539, #93117 ) ; +#65627 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98204 ), #91697 ) ; +#65628 = ORIENTED_EDGE ( 'NONE', *, *, #67384, .T. ) ; +#65630 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65629 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65631 = ORIENTED_EDGE ( 'NONE', *, *, #10720, .F. ) ; +#65632 = ORIENTED_EDGE ( 'NONE', *, *, #91309, .F. ) ; +#65633 = EDGE_CURVE ( 'NONE', #8714, #26448, #88049, .T. ) ; +#65634 = CARTESIAN_POINT ( 'NONE', ( 1.134404406240698826, -1.209605127971634442, 0.8099999999998579447 ) ) ; +#65635 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84055 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93, #54773, #17916 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65636 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21607 ) ) ; +#65637 = SURFACE_STYLE_USAGE ( .BOTH. , #34531 ) ; +#65638 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#65639 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#65640 = VERTEX_POINT ( 'NONE', #24786 ) ; +#65641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31456 ), #28194 ) ; +#65642 = FILL_AREA_STYLE_COLOUR ( '', #5919 ) ; +#65643 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15002 ) ) ; +#65644 = ORIENTED_EDGE ( 'NONE', *, *, #48118, .T. ) ; +#65645 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65646 = ORIENTED_EDGE ( 'NONE', *, *, #52115, .F. ) ; +#65647 = SURFACE_STYLE_FILL_AREA ( #17153 ) ; +#65649 = FILL_AREA_STYLE_COLOUR ( '', #63692 ) ; +#65648 = FACE_OUTER_BOUND ( 'NONE', #48574, .T. ) ; +#65650 = CARTESIAN_POINT ( 'NONE', ( -0.9982971928311329401, -1.296162859166370307, 0.8299999999999999600 ) ) ; +#65651 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31014 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100315, #60174, #28981 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65652 = EDGE_CURVE ( 'NONE', #56911, #18257, #32420, .T. ) ; +#65653 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65654 = ADVANCED_FACE ( 'NONE', ( #48254 ), #49249, .T. ) ; +#65655 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #73339, #50860, #97276, #26374 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65656 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65657 = AXIS2_PLACEMENT_3D ( 'NONE', #88686, #80054, #19756 ) ; +#65658 = SURFACE_STYLE_FILL_AREA ( #13455 ) ; +#65659 = LINE ( 'NONE', #61030, #83784 ) ; +#65660 = LINE ( 'NONE', #73829, #21398 ) ; +#65661 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65662 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65663 = ORIENTED_EDGE ( 'NONE', *, *, #12589, .T. ) ; +#65664 = LINE ( 'NONE', #48856, #100605 ) ; +#65665 = LINE ( 'NONE', #65160, #62762 ) ; +#65666 = VECTOR ( 'NONE', #97508, 1000.000000000000000 ) ; +#65668 = FILL_AREA_STYLE_COLOUR ( '', #90033 ) ; +#65667 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.75342000000000020, 0.8648700000000000276 ) ) ; +#65669 = FILL_AREA_STYLE ('',( #79499 ) ) ; +#65670 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#65671 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65672 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#65673 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#65674 = STYLED_ITEM ( 'NONE', ( #63852 ), #52881 ) ; +#65675 = VERTEX_POINT ( 'NONE', #12865 ) ; +#65676 = SURFACE_STYLE_USAGE ( .BOTH. , #36061 ) ; +#65678 = EDGE_CURVE ( 'NONE', #13197, #9357, #90039, .T. ) ; +#65677 = SURFACE_SIDE_STYLE ('',( #2905 ) ) ; +#65679 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65680 = PLANE ( 'NONE', #88786 ) ; +#65681 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65682 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65683 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#65684 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19972 ), #75443 ) ; +#65685 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36613, 'distance_accuracy_value', 'NONE'); +#65686 = FILL_AREA_STYLE ('',( #88662 ) ) ; +#65687 = SURFACE_STYLE_USAGE ( .BOTH. , #33036 ) ; +#65688 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65689 = PRESENTATION_STYLE_ASSIGNMENT (( #34577 ) ) ; +#65690 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#65691 = EDGE_CURVE ( 'NONE', #48584, #44869, #4280, .T. ) ; +#65692 = SURFACE_STYLE_USAGE ( .BOTH. , #50416 ) ; +#65693 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65694 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65695 = LINE ( 'NONE', #65186, #12869 ) ; +#65696 = ADVANCED_FACE ( 'NONE', ( #59950 ), #91052, .T. ) ; +#65697 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000001378, 0.8991599999999999593 ) ) ; +#65698 = SURFACE_STYLE_FILL_AREA ( #17699 ) ; +#65699 = PRESENTATION_STYLE_ASSIGNMENT (( #43209 ) ) ; +#65700 = CARTESIAN_POINT ( 'NONE', ( 1.799876578750339906, -1.066767002799750008, 0.8299999999999997380 ) ) ; +#65701 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42808 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7936, #53500, #47330 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65702 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25788 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71088, #77732, #2158 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65703 = SURFACE_SIDE_STYLE ('',( #35592 ) ) ; +#65704 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65705 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65706 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65707 = FILL_AREA_STYLE ('',( #27931 ) ) ; +#65708 = VERTEX_POINT ( 'NONE', #98621 ) ; +#65709 = LINE ( 'NONE', #10458, #24221 ) ; +#65710 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#65711 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43583, 'distance_accuracy_value', 'NONE'); +#65713 = VECTOR ( 'NONE', #77389, 1000.000000000000000 ) ; +#65712 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 2.700330000000000563, 0.8648700000000000276 ) ) ; +#65714 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24995 ) ) ; +#65715 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93825, 'distance_accuracy_value', 'NONE'); +#65716 = VECTOR ( 'NONE', #53124, 1000.000000000000000 ) ; +#65717 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65718 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65719 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4820 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67876, #52105, #29111 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65720 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91778 ), #3758 ) ; +#65721 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70962 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18981, #71624, #18476 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65722 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65723 = EDGE_CURVE ( 'NONE', #79474, #65143, #28758, .T. ) ; +#65724 = ORIENTED_EDGE ( 'NONE', *, *, #52803, .F. ) ; +#65725 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#65726 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65727 = STYLED_ITEM ( 'NONE', ( #73555 ), #59683 ) ; +#65728 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#65729 = VECTOR ( 'NONE', #75841, 1000.000000000000000 ) ; +#65730 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65731 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80523, 'distance_accuracy_value', 'NONE'); +#65732 = SURFACE_STYLE_USAGE ( .BOTH. , #57598 ) ; +#65733 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92357, #92824, #23438 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65734 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55526, 'distance_accuracy_value', 'NONE'); +#65735 = SURFACE_STYLE_FILL_AREA ( #51437 ) ; +#65736 = SURFACE_STYLE_FILL_AREA ( #34604 ) ; +#65737 = EDGE_CURVE ( 'NONE', #80338, #13051, #32791, .T. ) ; +#65738 = EDGE_CURVE ( 'NONE', #91985, #30348, #99520, .T. ) ; +#65739 = EDGE_LOOP ( 'NONE', ( #11160, #64846, #19678, #10636, #76399, #81846 ) ) ; +#65740 = VERTEX_POINT ( 'NONE', #11846 ) ; +#65741 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000009992, 3.123820061220065281, 0.000000000000000000 ) ) ; +#65742 = PRESENTATION_STYLE_ASSIGNMENT (( #66234 ) ) ; +#65743 = STYLED_ITEM ( 'NONE', ( #9869 ), #67189 ) ; +#65744 = ORIENTED_EDGE ( 'NONE', *, *, #39715, .T. ) ; +#65745 = CARTESIAN_POINT ( 'NONE', ( 0.2454021686453040363, -1.061343041336519910, 0.8299999999999996270 ) ) ; +#65746 = EDGE_CURVE ( 'NONE', #30660, #12898, #13363, .T. ) ; +#65747 = SURFACE_SIDE_STYLE ('',( #49415 ) ) ; +#65748 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65749 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #68089, #41901 ) ; +#65750 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65752 = ORIENTED_EDGE ( 'NONE', *, *, #18126, .T. ) ; +#65751 = ORIENTED_EDGE ( 'NONE', *, *, #2266, .F. ) ; +#65753 = EDGE_CURVE ( 'NONE', #12693, #52415, #43076, .T. ) ; +#65754 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15096 ), #86883 ) ; +#65755 = VERTEX_POINT ( 'NONE', #98135 ) ; +#65756 = ORIENTED_EDGE ( 'NONE', *, *, #55673, .F. ) ; +#65757 = CARTESIAN_POINT ( 'NONE', ( 1.900854206603999952, -1.350767436372750208, 0.8100000000000000533 ) ) ; +#65758 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65759 = EDGE_LOOP ( 'NONE', ( #37841, #40524, #98879, #86191 ) ) ; +#65760 = STYLED_ITEM ( 'NONE', ( #81952 ), #53172 ) ; +#65761 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#65762 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30409, #85064, #55481, #31458 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65763 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65764 = VERTEX_POINT ( 'NONE', #66074 ) ; +#65765 = ORIENTED_EDGE ( 'NONE', *, *, #10092, .F. ) ; +#65766 = SURFACE_STYLE_FILL_AREA ( #34638 ) ; +#65767 = VECTOR ( 'NONE', #52288, 1000.000000000000000 ) ; +#65768 = EDGE_LOOP ( 'NONE', ( #27510, #35783, #682, #15492 ) ) ; +#65769 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8583 ), #56016 ) ; +#65770 = ADVANCED_FACE ( 'NONE', ( #68046 ), #60446, .T. ) ; +#65771 = ORIENTED_EDGE ( 'NONE', *, *, #70960, .F. ) ; +#65772 = EDGE_CURVE ( 'NONE', #63765, #79372, #15422, .T. ) ; +#65773 = DIRECTION ( 'NONE', ( -4.344024262657780003E-34, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65774 = CARTESIAN_POINT ( 'NONE', ( 1.874834857517529985, -1.237898259965849901, 0.8300000000000004041 ) ) ; +#65775 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#65776 = SURFACE_SIDE_STYLE ('',( #82109 ) ) ; +#65778 = ORIENTED_EDGE ( 'NONE', *, *, #25745, .F. ) ; +#65777 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#65779 = ORIENTED_EDGE ( 'NONE', *, *, #274, .F. ) ; +#65780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65781 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23355 ), #70637 ) ; +#65782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70640 ) ) ; +#65783 = VERTEX_POINT ( 'NONE', #60936 ) ; +#65784 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65785 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#65786 = ORIENTED_EDGE ( 'NONE', *, *, #17225, .T. ) ; +#65787 = ORIENTED_EDGE ( 'NONE', *, *, #64391, .T. ) ; +#65789 = SURFACE_STYLE_FILL_AREA ( #98343 ) ; +#65788 = SURFACE_STYLE_FILL_AREA ( #20301 ) ; +#65790 = FACE_OUTER_BOUND ( 'NONE', #93771, .T. ) ; +#65791 = ADVANCED_FACE ( 'NONE', ( #47093 ), #7697, .T. ) ; +#65792 = VECTOR ( 'NONE', #48248, 1000.000000000000227 ) ; +#65793 = CARTESIAN_POINT ( 'NONE', ( -0.3663670119008199944, -1.086125944437150048, 0.8299999999999999600 ) ) ; +#65794 = FILL_AREA_STYLE ('',( #78217 ) ) ; +#65795 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65796 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65797 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51149 ) ) ; +#65798 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#65799 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70653 ), #33138 ) ; +#65800 = ORIENTED_EDGE ( 'NONE', *, *, #58027, .T. ) ; +#65801 = CARTESIAN_POINT ( 'NONE', ( 0.02260986327491390155, -1.199770973383029959, 0.8100000000000000533 ) ) ; +#65802 = VERTEX_POINT ( 'NONE', #93521 ) ; +#65803 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65804 = AXIS2_PLACEMENT_3D ( 'NONE', #20082, #57417, #41585 ) ; +#65805 = CARTESIAN_POINT ( 'NONE', ( 1.250776364246900085, -1.163804091156239950, 0.8299999999999999600 ) ) ; +#65806 = LINE ( 'NONE', #4006, #23567 ) ; +#65807 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65808 = FILL_AREA_STYLE ('',( #43811 ) ) ; +#65809 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#65810 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65811 = EDGE_LOOP ( 'NONE', ( #70384, #49315, #52418, #49863 ) ) ; +#65812 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#65813 = CYLINDRICAL_SURFACE ( 'NONE', #73280, 0.04341445994543620401 ) ; +#65814 = CARTESIAN_POINT ( 'NONE', ( 0.1720843054334539879, -1.066823530734400061, 0.8100000000000000533 ) ) ; +#65815 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65816 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65817 = FILL_AREA_STYLE ('',( #81153 ) ) ; +#65818 = FACE_OUTER_BOUND ( 'NONE', #84789, .T. ) ; +#65819 = FILL_AREA_STYLE ('',( #51535 ) ) ; +#65820 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65821 = CARTESIAN_POINT ( 'NONE', ( 1.999999999999999556, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#65822 = FILL_AREA_STYLE_COLOUR ( '', #68241 ) ; +#65823 = FILL_AREA_STYLE ('',( #80654 ) ) ; +#65824 = SURFACE_STYLE_FILL_AREA ( #74494 ) ; +#65825 = FILL_AREA_STYLE ('',( #16931 ) ) ; +#65826 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38216, 'distance_accuracy_value', 'NONE'); +#65827 = VERTEX_POINT ( 'NONE', #24151 ) ; +#65828 = CYLINDRICAL_SURFACE ( 'NONE', #53469, 0.05000000000000012768 ) ; +#65829 = FACE_OUTER_BOUND ( 'NONE', #8656, .T. ) ; +#65830 = VERTEX_POINT ( 'NONE', #14902 ) ; +#65831 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#65832 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#65833 = CARTESIAN_POINT ( 'NONE', ( 1.702357802111380103, -0.9001170352889870108, 0.8299999999999999600 ) ) ; +#65834 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85418 ), #90301 ) ; +#65835 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, 3.099999999999969891, 0.000000000000000000 ) ) ; +#65836 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#65837 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90306 ), #5504 ) ; +#65838 = VECTOR ( 'NONE', #92922, 1000.000000000000000 ) ; +#65839 = VERTEX_POINT ( 'NONE', #22105 ) ; +#65840 = ADVANCED_FACE ( 'NONE', ( #55298 ), #70061, .T. ) ; +#65841 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82183 ) ) ; +#65842 = ORIENTED_EDGE ( 'NONE', *, *, #50149, .F. ) ; +#65843 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65844 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65845 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65846 = LINE ( 'NONE', #50551, #48271 ) ; +#65847 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65848 = CARTESIAN_POINT ( 'NONE', ( -0.5594799075883629680, -1.188256883098049999, 0.8100000000000000533 ) ) ; +#65849 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47974, 'distance_accuracy_value', 'NONE'); +#65850 = VECTOR ( 'NONE', #54128, 1000.000000000000000 ) ; +#65851 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#65852 = PRESENTATION_STYLE_ASSIGNMENT (( #66839 ) ) ; +#65853 = SURFACE_STYLE_FILL_AREA ( #58226 ) ; +#65854 = STYLED_ITEM ( 'NONE', ( #31906 ), #21483 ) ; +#65855 = EDGE_CURVE ( 'NONE', #68558, #18766, #55703, .T. ) ; +#65856 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#65857 = EDGE_LOOP ( 'NONE', ( #13416, #84130, #65231, #98505, #39758, #60140 ) ) ; +#65858 = VECTOR ( 'NONE', #64668, 1000.000000000000114 ) ; +#65859 = AXIS2_PLACEMENT_3D ( 'NONE', #21336, #44790, #74973 ) ; +#65860 = LINE ( 'NONE', #19377, #68263 ) ; +#65861 = ORIENTED_EDGE ( 'NONE', *, *, #6208, .F. ) ; +#65862 = PRESENTATION_STYLE_ASSIGNMENT (( #73015 ) ) ; +#65863 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#65864 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65865 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#65866 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61976, #46082, #78293 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65867 = CARTESIAN_POINT ( 'NONE', ( -1.129230981225310071, -0.9561532343638800002, 0.8100000000000000533 ) ) ; +#65868 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65869 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65872 = EDGE_LOOP ( 'NONE', ( #77564, #17767, #3076, #41308 ) ) ; +#65871 = ORIENTED_EDGE ( 'NONE', *, *, #94555, .T. ) ; +#65873 = EDGE_CURVE ( 'NONE', #88609, #53420, #23686, .T. ) ; +#65874 = PLANE ( 'NONE', #5987 ) ; +#65875 = VERTEX_POINT ( 'NONE', #25645 ) ; +#65876 = FILL_AREA_STYLE ('',( #17873 ) ) ; +#65877 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99996 ), #56119 ) ; +#65878 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65879 = ORIENTED_EDGE ( 'NONE', *, *, #18286, .F. ) ; +#65880 = EDGE_CURVE ( 'NONE', #59551, #74962, #73111, .T. ) ; +#65881 = VERTEX_POINT ( 'NONE', #16416 ) ; +#65882 = SURFACE_STYLE_FILL_AREA ( #25583 ) ; +#65883 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#65884 = SURFACE_SIDE_STYLE ('',( #34763 ) ) ; +#65885 = VECTOR ( 'NONE', #43991, 1000.000000000000000 ) ; +#65886 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65887 = ORIENTED_EDGE ( 'NONE', *, *, #13575, .F. ) ; +#65888 = ORIENTED_EDGE ( 'NONE', *, *, #11249, .F. ) ; +#65889 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30008 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62140, #820, #54972 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65890 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#65891 = EDGE_LOOP ( 'NONE', ( #23036, #11280, #14610, #68835 ) ) ; +#65892 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#65893 = ADVANCED_FACE ( 'NONE', ( #26662 ), #71092, .T. ) ; +#65894 = EDGE_CURVE ( 'NONE', #67841, #53940, #79259, .T. ) ; +#65895 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65897 = ADVANCED_FACE ( 'NONE', ( #88423 ), #40978, .T. ) ; +#65896 = ORIENTED_EDGE ( 'NONE', *, *, #79509, .F. ) ; +#65898 = ADVANCED_FACE ( 'NONE', ( #72105 ), #32792, .F. ) ; +#65899 = SURFACE_SIDE_STYLE ('',( #34277 ) ) ; +#65900 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65901 = ORIENTED_EDGE ( 'NONE', *, *, #43597, .F. ) ; +#65902 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#65903 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#65904 = ORIENTED_EDGE ( 'NONE', *, *, #82446, .T. ) ; +#65905 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65906 = ORIENTED_EDGE ( 'NONE', *, *, #99198, .F. ) ; +#65907 = LINE ( 'NONE', #3615, #20381 ) ; +#65908 = SURFACE_STYLE_FILL_AREA ( #65376 ) ; +#65909 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7121 ) ) ; +#65910 = EDGE_CURVE ( 'NONE', #53201, #95367, #49136, .T. ) ; +#65911 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52850 ) ) ; +#65912 = FACE_OUTER_BOUND ( 'NONE', #54278, .T. ) ; +#65913 = CARTESIAN_POINT ( 'NONE', ( -1.355486452235469930, -1.128484622308769891, 0.8300000000000000711 ) ) ; +#65914 = FILL_AREA_STYLE ('',( #59798 ) ) ; +#65915 = EDGE_CURVE ( 'NONE', #26971, #66829, #34831, .T. ) ; +#65916 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65918 = LINE ( 'NONE', #48078, #46581 ) ; +#65917 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000444, 0.000000000000000000 ) ) ; +#65919 = CARTESIAN_POINT ( 'NONE', ( 1.674754468276729913, -0.9004049383407729534, 0.8299999999999997380 ) ) ; +#65920 = VERTEX_POINT ( 'NONE', #65957 ) ; +#65921 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#65922 = AXIS2_PLACEMENT_3D ( 'NONE', #80137, #90659, #73836 ) ; +#65923 = EDGE_LOOP ( 'NONE', ( #54953, #2987, #69075, #91794 ) ) ; +#65924 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000001001, 0.8991599999999999593 ) ) ; +#65925 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.000000000000000000 ) ) ; +#65926 = VECTOR ( 'NONE', #48608, 1000.000000000000000 ) ; +#65927 = SURFACE_STYLE_FILL_AREA ( #27135 ) ; +#65929 = LINE ( 'NONE', #34804, #96433 ) ; +#65928 = CARTESIAN_POINT ( 'NONE', ( 1.325735931288071434, 0.6892893218813450629, -1.100000000000000089 ) ) ; +#65930 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65931 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44707, #27938, #90185, #13514 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#65932 = FACE_OUTER_BOUND ( 'NONE', #75560, .T. ) ; +#65933 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#65934 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54725 ) ) ; +#65935 = PRESENTATION_STYLE_ASSIGNMENT (( #51642 ) ) ; +#65936 = FILL_AREA_STYLE_COLOUR ( '', #99584 ) ; +#65937 = VECTOR ( 'NONE', #11315, 1000.000000000000000 ) ; +#65938 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65939 = VECTOR ( 'NONE', #26695, 1000.000000000000000 ) ; +#65940 = ORIENTED_EDGE ( 'NONE', *, *, #63824, .T. ) ; +#65941 = STYLED_ITEM ( 'NONE', ( #8691 ), #29107 ) ; +#65942 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 9.983529000000000764, 0.8648700000000000276 ) ) ; +#65944 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65943 = LINE ( 'NONE', #20970, #56930 ) ; +#65945 = LINE ( 'NONE', #88917, #68415 ) ; +#65946 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#65947 = STYLED_ITEM ( 'NONE', ( #25095 ), #68619 ) ; +#65949 = EDGE_CURVE ( 'NONE', #66177, #96516, #4642, .T. ) ; +#65948 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22198, 'distance_accuracy_value', 'NONE'); +#65950 = ORIENTED_EDGE ( 'NONE', *, *, #60543, .T. ) ; +#65951 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65953 = CARTESIAN_POINT ( 'NONE', ( -1.011710337664210035, -1.062017517080650064, 0.8299999999999999600 ) ) ; +#65954 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#65955 = CARTESIAN_POINT ( 'NONE', ( 6.827451499499826326, 2.438700500500175838, 0.8991599999999999593 ) ) ; +#65956 = CIRCLE ( 'NONE', #10439, 0.09999999999999999167 ) ; +#65957 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, 3.149999999999979927, 0.000000000000000000 ) ) ; +#65958 = CARTESIAN_POINT ( 'NONE', ( 4.105090750249975606, 4.241822750249974128, 0.8991599999999999593 ) ) ; +#65959 = ORIENTED_EDGE ( 'NONE', *, *, #92630, .F. ) ; +#65960 = AXIS2_PLACEMENT_3D ( 'NONE', #98840, #58663, #73959 ) ; +#65961 = EDGE_LOOP ( 'NONE', ( #97118, #75462, #47231, #61721 ) ) ; +#65962 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97426, 'distance_accuracy_value', 'NONE'); +#65963 = CARTESIAN_POINT ( 'NONE', ( -3.233333333333333393, 3.500000000000000000, 0.000000000000000000 ) ) ; +#65964 = CARTESIAN_POINT ( 'NONE', ( -0.2052975279651420015, -1.010243534007990052, 0.8299999999999999600 ) ) ; +#65965 = SURFACE_STYLE_FILL_AREA ( #80801 ) ; +#65966 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65967 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#65968 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30282 ) ) ; +#65969 = FILL_AREA_STYLE_COLOUR ( '', #23961 ) ; +#65970 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#65971 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, 0.1400000000000000133 ) ) ; +#65972 = VERTEX_POINT ( 'NONE', #19973 ) ; +#65973 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.7000000000000001776, 0.000000000000000000 ) ) ; +#65975 = ADVANCED_FACE ( 'NONE', ( #20472 ), #89921, .F. ) ; +#65974 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.500000000000000000, -0.02000000000004190093 ) ) ; +#65976 = DIRECTION ( 'NONE', ( 1.084202172485504237E-15, 0.000000000000000000, -1.000000000000000000 ) ) ; +#65977 = ORIENTED_EDGE ( 'NONE', *, *, #17069, .T. ) ; +#65978 = DIRECTION ( 'NONE', ( 0.3643423458302811890, 0.000000000000000000, 0.9312650831180602218 ) ) ; +#65979 = VECTOR ( 'NONE', #7124, 1000.000000000000000 ) ; +#65980 = VECTOR ( 'NONE', #33557, 1000.000000000000114 ) ; +#65981 = ORIENTED_EDGE ( 'NONE', *, *, #39476, .F. ) ; +#65982 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72732 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99506, #60831, #77631 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65983 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#65984 = PRESENTATION_STYLE_ASSIGNMENT (( #20005 ) ) ; +#65985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#65986 = SURFACE_STYLE_USAGE ( .BOTH. , #65463 ) ; +#65987 = ORIENTED_EDGE ( 'NONE', *, *, #14276, .T. ) ; +#65988 = PRESENTATION_STYLE_ASSIGNMENT (( #82811 ) ) ; +#65989 = EDGE_LOOP ( 'NONE', ( #80705, #50851, #2172, #66246, #38348, #89355 ) ) ; +#65990 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#65991 = VECTOR ( 'NONE', #19833, 1000.000000000000000 ) ; +#65992 = VECTOR ( 'NONE', #88547, 1000.000000000000000 ) ; +#65993 = ORIENTED_EDGE ( 'NONE', *, *, #98624, .F. ) ; +#65994 = EDGE_LOOP ( 'NONE', ( #86290, #66744, #29209, #70846, #70767, #30913 ) ) ; +#65997 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79044 ) ) ; +#65996 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1143 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86077, #810, #17130 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#65995 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#65998 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#65999 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, -0.1400000000000000411 ) ) ; +#66000 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66001 = FACE_OUTER_BOUND ( 'NONE', #19026, .T. ) ; +#66003 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#66002 = CARTESIAN_POINT ( 'NONE', ( 0.3405668653832410464, -0.9628054983551439516, 0.8299999999999999600 ) ) ; +#66004 = ORIENTED_EDGE ( 'NONE', *, *, #29112, .T. ) ; +#66006 = ORIENTED_EDGE ( 'NONE', *, *, #72191, .T. ) ; +#66005 = ORIENTED_EDGE ( 'NONE', *, *, #60672, .F. ) ; +#66007 = VERTEX_POINT ( 'NONE', #20989 ) ; +#66008 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94419 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71002, #31192, #32209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66009 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66010 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3978 ) ) ; +#66011 = ORIENTED_EDGE ( 'NONE', *, *, #29864, .T. ) ; +#66012 = ORIENTED_EDGE ( 'NONE', *, *, #25733, .F. ) ; +#66013 = EDGE_CURVE ( 'NONE', #9513, #34176, #43460, .T. ) ; +#66014 = SURFACE_STYLE_FILL_AREA ( #5677 ) ; +#66015 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#66016 = EDGE_LOOP ( 'NONE', ( #18763, #63271, #86933, #54988 ) ) ; +#66017 = CARTESIAN_POINT ( 'NONE', ( 0.001420454545454329087, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#66018 = ORIENTED_EDGE ( 'NONE', *, *, #10674, .T. ) ; +#66019 = CARTESIAN_POINT ( 'NONE', ( 0.3828981658612353733, -1.290083047920857595, 0.8100000000000002753 ) ) ; +#66020 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.000000000000000000 ) ) ; +#66021 = STYLED_ITEM ( 'NONE', ( #23672 ), #68289 ) ; +#66022 = CARTESIAN_POINT ( 'NONE', ( -1.150000000000000133, 0.7099999999999999645, 1.079289321881345298 ) ) ; +#66023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72568 ), #850 ) ; +#66024 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66025 = EDGE_CURVE ( 'NONE', #2612, #90311, #3656, .T. ) ; +#66026 = CARTESIAN_POINT ( 'NONE', ( 1.754677333481259982, -1.433486393616560051, 0.8299999999999999600 ) ) ; +#66028 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#66027 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#66029 = PRESENTATION_STYLE_ASSIGNMENT (( #73689 ) ) ; +#66030 = FACE_OUTER_BOUND ( 'NONE', #96581, .T. ) ; +#66031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100687, #15518, #92617 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66032 = SURFACE_SIDE_STYLE ('',( #34911 ) ) ; +#66033 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54615 ), #12227 ) ; +#66034 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5633 ) ) ; +#66035 = FILL_AREA_STYLE ('',( #99086 ) ) ; +#66036 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66037 = DIRECTION ( 'NONE', ( 0.3643423458302801343, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#66038 = FILL_AREA_STYLE_COLOUR ( '', #98486 ) ; +#66039 = AXIS2_PLACEMENT_3D ( 'NONE', #9025, #46885, #15208 ) ; +#66040 = LINE ( 'NONE', #97149, #70225 ) ; +#66041 = VECTOR ( 'NONE', #39627, 1000.000000000000000 ) ; +#66042 = VERTEX_POINT ( 'NONE', #19482 ) ; +#66043 = VECTOR ( 'NONE', #65845, 1000.000000000000000 ) ; +#66044 = AXIS2_PLACEMENT_3D ( 'NONE', #73563, #18407, #72543 ) ; +#66045 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66046 = LINE ( 'NONE', #64539, #20176 ) ; +#66047 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66048 = FACE_OUTER_BOUND ( 'NONE', #75267, .T. ) ; +#66049 = VERTEX_POINT ( 'NONE', #50654 ) ; +#66050 = EDGE_CURVE ( 'NONE', #45115, #2903, #83283, .T. ) ; +#66051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66053 = LINE ( 'NONE', #85625, #43893 ) ; +#66052 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82390 ) ) ; +#66055 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66054 = FACE_OUTER_BOUND ( 'NONE', #68031, .T. ) ; +#66056 = CARTESIAN_POINT ( 'NONE', ( 1.592056040834880060, -1.030915998478540097, 0.8299999999999999600 ) ) ; +#66057 = CARTESIAN_POINT ( 'NONE', ( -0.2277176615892120282, -1.378252124432310044, 0.8100000000000000533 ) ) ; +#66058 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66059 = VECTOR ( 'NONE', #81920, 1000.000000000000000 ) ; +#66060 = FILL_AREA_STYLE ('',( #9833 ) ) ; +#66061 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66062 = PLANE ( 'NONE', #99967 ) ; +#66063 = EDGE_CURVE ( 'NONE', #67337, #5244, #15812, .T. ) ; +#66064 = EDGE_LOOP ( 'NONE', ( #77025, #51715, #22307, #59723 ) ) ; +#66065 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66066 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#66068 = STYLED_ITEM ( 'NONE', ( #87633 ), #27501 ) ; +#66067 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26942 ), #56339 ) ; +#66069 = FILL_AREA_STYLE ('',( #65061 ) ) ; +#66070 = VECTOR ( 'NONE', #85005, 1000.000000000000000 ) ; +#66071 = SURFACE_STYLE_USAGE ( .BOTH. , #34944 ) ; +#66072 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66073 = SURFACE_STYLE_FILL_AREA ( #96679 ) ; +#66074 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980549, 0.000000000000000000 ) ) ; +#66075 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#66076 = PRESENTATION_STYLE_ASSIGNMENT (( #73732 ) ) ; +#66077 = PLANE ( 'NONE', #92449 ) ; +#66078 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66079 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66080 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66081 = LINE ( 'NONE', #81432, #100739 ) ; +#66082 = ORIENTED_EDGE ( 'NONE', *, *, #75923, .T. ) ; +#66083 = ORIENTED_EDGE ( 'NONE', *, *, #39725, .T. ) ; +#66084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68890 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79960, #72788, #71785 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66085 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66086 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8099999999999629718 ) ) ; +#66087 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#66088 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.005000000000000000104, -0.2400000000000000189 ) ) ; +#66089 = VECTOR ( 'NONE', #61975, 1000.000000000000000 ) ; +#66090 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #21547, #61398, #6166, #76674 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66091 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#66092 = SURFACE_STYLE_FILL_AREA ( #81442 ) ; +#66093 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#66094 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#66095 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66096 = ORIENTED_EDGE ( 'NONE', *, *, #16729, .T. ) ; +#66097 = CARTESIAN_POINT ( 'NONE', ( -2.523820061220085176, -3.100000000000000089, 0.000000000000000000 ) ) ; +#66098 = SURFACE_STYLE_FILL_AREA ( #58973 ) ; +#66099 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#66100 = ORIENTED_EDGE ( 'NONE', *, *, #21267, .F. ) ; +#66101 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66102 = STYLED_ITEM ( 'NONE', ( #26109 ), #72665 ) ; +#66103 = ADVANCED_FACE ( 'NONE', ( #15284 ), #29159, .F. ) ; +#66104 = VECTOR ( 'NONE', #84639, 1000.000000000000000 ) ; +#66105 = FILL_AREA_STYLE ('',( #75761 ) ) ; +#66106 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66107 = ORIENTED_EDGE ( 'NONE', *, *, #54441, .T. ) ; +#66108 = FILL_AREA_STYLE_COLOUR ( '', #66190 ) ; +#66109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66110 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22066 ), #12297 ) ; +#66111 = VECTOR ( 'NONE', #33542, 1000.000000000000000 ) ; +#66112 = FILL_AREA_STYLE ('',( #5782 ) ) ; +#66113 = ADVANCED_FACE ( 'NONE', ( #53643 ), #37335, .F. ) ; +#66114 = ORIENTED_EDGE ( 'NONE', *, *, #52604, .F. ) ; +#66115 = EDGE_CURVE ( 'NONE', #46216, #78767, #7077, .T. ) ; +#66116 = STYLED_ITEM ( 'NONE', ( #1848 ), #82729 ) ; +#66117 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66118 = FACE_OUTER_BOUND ( 'NONE', #1414, .T. ) ; +#66119 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#66120 = VERTEX_POINT ( 'NONE', #14779 ) ; +#66121 = AXIS2_PLACEMENT_3D ( 'NONE', #2055, #64335, #95441 ) ; +#66122 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #35830, #44431 ), + ( #44920, #45420 ), + ( #43955, #67426 ), + ( #84271, #51655 ), + ( #82766, #12744 ), + ( #99970, #98984 ), + ( #91912, #76596 ), + ( #51136, #28635 ), + ( #90929, #75116 ), + ( #21976, #75599 ), + ( #29626, #67911 ), + ( #37810, #59831 ), + ( #29150, #60319 ), + ( #53136, #30121 ), + ( #90415, #82282 ), + ( #91424, #52641 ), + ( #21472, #12230 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07361161809163040137, 0.1418704760126159869, 0.2047010881220309997, 0.2650638462607379786, 0.3226075809791700277, 0.3798957495557009900, 0.4370254124446700250, 0.4956449832836989922, 0.5547100597432720326, 0.6152773224479549663, 0.6777605979153450422, 0.7425370015046289796, 0.8723910695608639854, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66123 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49821 ), #46481 ) ; +#66124 = ORIENTED_EDGE ( 'NONE', *, *, #21366, .T. ) ; +#66125 = ORIENTED_EDGE ( 'NONE', *, *, #18686, .F. ) ; +#66126 = EDGE_CURVE ( 'NONE', #69981, #52069, #23512, .T. ) ; +#66127 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38378, 'distance_accuracy_value', 'NONE'); +#66128 = LINE ( 'NONE', #97240, #83377 ) ; +#66130 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66129 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66131 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66132 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#66133 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66134 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66135 = VERTEX_POINT ( 'NONE', #85770 ) ; +#66137 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46681 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63913, #47570, #63433 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66136 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77488 ), #82476 ) ; +#66138 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000011470, -1.979898987322330051, 0.6999285677838846809 ) ) ; +#66139 = STYLED_ITEM ( 'NONE', ( #39946 ), #99068 ) ; +#66140 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#66141 = ORIENTED_EDGE ( 'NONE', *, *, #34722, .T. ) ; +#66142 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.9000000000000003553, -0.02000000000000000042 ) ) ; +#66143 = EDGE_LOOP ( 'NONE', ( #7872, #88913, #57246, #37991 ) ) ; +#66144 = AXIS2_PLACEMENT_3D ( 'NONE', #77595, #7557, #38799 ) ; +#66145 = EDGE_CURVE ( 'NONE', #14593, #67038, #60328, .T. ) ; +#66146 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#66147 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66148 = ORIENTED_EDGE ( 'NONE', *, *, #15373, .T. ) ; +#66149 = PLANE ( 'NONE', #58209 ) ; +#66150 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13902 ) ) ; +#66151 = ORIENTED_EDGE ( 'NONE', *, *, #59556, .T. ) ; +#66152 = FACE_OUTER_BOUND ( 'NONE', #85488, .T. ) ; +#66153 = ORIENTED_EDGE ( 'NONE', *, *, #62564, .T. ) ; +#66154 = LINE ( 'NONE', #11937, #32399 ) ; +#66155 = CARTESIAN_POINT ( 'NONE', ( -1.336283849596160200, -1.153389236204189983, 0.8100000000000000533 ) ) ; +#66156 = LINE ( 'NONE', #9439, #33506 ) ; +#66157 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#66158 = AXIS2_PLACEMENT_3D ( 'NONE', #10538, #27495, #74457 ) ; +#66159 = LINE ( 'NONE', #36044, #7079 ) ; +#66160 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#66161 = ORIENTED_EDGE ( 'NONE', *, *, #65894, .T. ) ; +#66162 = EDGE_CURVE ( 'NONE', #12591, #97527, #44930, .T. ) ; +#66163 = SURFACE_SIDE_STYLE ('',( #26380 ) ) ; +#66164 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#66167 = FILL_AREA_STYLE ('',( #58554 ) ) ; +#66166 = FILL_AREA_STYLE_COLOUR ( '', #37622 ) ; +#66165 = LINE ( 'NONE', #52373, #30013 ) ; +#66168 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16546, 'distance_accuracy_value', 'NONE'); +#66169 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, 3.266666666666653285, 3.495651678170078205E-76 ) ) ; +#66170 = SURFACE_STYLE_USAGE ( .BOTH. , #34050 ) ; +#66171 = VECTOR ( 'NONE', #72305, 1000.000000000000000 ) ; +#66172 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66173 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66174 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#66175 = PRESENTATION_STYLE_ASSIGNMENT (( #3884 ) ) ; +#66176 = EDGE_CURVE ( 'NONE', #73910, #79728, #57383, .T. ) ; +#66177 = VERTEX_POINT ( 'NONE', #31661 ) ; +#66178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51570 ) ) ; +#66179 = PRESENTATION_STYLE_ASSIGNMENT (( #18172 ) ) ; +#66180 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#66181 = FILL_AREA_STYLE ('',( #35067 ) ) ; +#66182 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87386 ), #4231 ) ; +#66184 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66183 = STYLED_ITEM ( 'NONE', ( #89803 ), #89605 ) ; +#66185 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66186 = SURFACE_STYLE_FILL_AREA ( #3891 ) ; +#66187 = FILL_AREA_STYLE_COLOUR ( '', #62729 ) ; +#66188 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43297 ) ) ; +#66190 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66189 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#66191 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66192 = SURFACE_STYLE_FILL_AREA ( #87662 ) ; +#66193 = SURFACE_SIDE_STYLE ('',( #20213 ) ) ; +#66194 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#66195 = SURFACE_STYLE_FILL_AREA ( #82036 ) ; +#66196 = FILL_AREA_STYLE_COLOUR ( '', #4939 ) ; +#66197 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#66198 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66199 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66200 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44854 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86767, #49484, #56150 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66201 = PLANE ( 'NONE', #12114 ) ; +#66202 = DIRECTION ( 'NONE', ( -0.9684929325968363312, 0.2490410398106700507, 0.000000000000000000 ) ) ; +#66204 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28658 ) ) ; +#66203 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.966666666666667007, 0.000000000000000000 ) ) ; +#66205 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#66206 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71081 ), #61274 ) ; +#66207 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.009158714663670502E-14 ) ) ; +#66208 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#66209 = SURFACE_STYLE_USAGE ( .BOTH. , #4404 ) ; +#66210 = ORIENTED_EDGE ( 'NONE', *, *, #33101, .T. ) ; +#66211 = SURFACE_SIDE_STYLE ('',( #88679 ) ) ; +#66212 = STYLED_ITEM ( 'NONE', ( #36655 ), #39348 ) ; +#66213 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17827 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21477, #6096, #59333 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66214 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66215 = STYLED_ITEM ( 'NONE', ( #4535 ), #5052 ) ; +#66216 = ADVANCED_FACE ( 'NONE', ( #10594 ), #92475, .T. ) ; +#66217 = VECTOR ( 'NONE', #38251, 1000.000000000000114 ) ; +#66218 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66219 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66220 = VERTEX_POINT ( 'NONE', #94924 ) ; +#66221 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#66222 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66223 = AXIS2_PLACEMENT_3D ( 'NONE', #22815, #21796, #12566 ) ; +#66224 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#66225 = SURFACE_STYLE_FILL_AREA ( #5399 ) ; +#66226 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36859 ), #79273 ) ; +#66227 = SURFACE_SIDE_STYLE ('',( #12522 ) ) ; +#66228 = FACE_OUTER_BOUND ( 'NONE', #12949, .T. ) ; +#66229 = EDGE_CURVE ( 'NONE', #55809, #61785, #41355, .T. ) ; +#66230 = ORIENTED_EDGE ( 'NONE', *, *, #56097, .T. ) ; +#66231 = ORIENTED_EDGE ( 'NONE', *, *, #87309, .F. ) ; +#66232 = EDGE_CURVE ( 'NONE', #80224, #141, #56696, .T. ) ; +#66233 = LINE ( 'NONE', #73403, #57025 ) ; +#66234 = SURFACE_STYLE_USAGE ( .BOTH. , #35119 ) ; +#66235 = ORIENTED_EDGE ( 'NONE', *, *, #84441, .T. ) ; +#66236 = SURFACE_STYLE_USAGE ( .BOTH. , #26438 ) ; +#66237 = VECTOR ( 'NONE', #51228, 1000.000000000000000 ) ; +#66238 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#66239 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#66240 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#66241 = LINE ( 'NONE', #12534, #72450 ) ; +#66242 = PRESENTATION_STYLE_ASSIGNMENT (( #75903 ) ) ; +#66243 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19352 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67512, #50252, #3246 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66245 = ORIENTED_EDGE ( 'NONE', *, *, #58440, .T. ) ; +#66244 = ORIENTED_EDGE ( 'NONE', *, *, #17993, .T. ) ; +#66246 = ORIENTED_EDGE ( 'NONE', *, *, #46489, .F. ) ; +#66247 = EDGE_LOOP ( 'NONE', ( #49976, #16401, #10384, #98522 ) ) ; +#66248 = FILL_AREA_STYLE_COLOUR ( '', #67063 ) ; +#66249 = EDGE_CURVE ( 'NONE', #3594, #3165, #16305, .T. ) ; +#66250 = AXIS2_PLACEMENT_3D ( 'NONE', #9308, #95126, #95632 ) ; +#66251 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28681, 'distance_accuracy_value', 'NONE'); +#66252 = VECTOR ( 'NONE', #76585, 1000.000000000000000 ) ; +#66253 = CYLINDRICAL_SURFACE ( 'NONE', #16346, 0.2137111836784290342 ) ; +#66255 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66254 = PRESENTATION_STYLE_ASSIGNMENT (( #98805 ) ) ; +#66256 = VERTEX_POINT ( 'NONE', #1541 ) ; +#66257 = VECTOR ( 'NONE', #3135, 1000.000000000000000 ) ; +#66258 = FILL_AREA_STYLE_COLOUR ( '', #30292 ) ; +#66259 = ADVANCED_FACE ( 'NONE', ( #72467 ), #63832, .T. ) ; +#66260 = LINE ( 'NONE', #11538, #4928 ) ; +#66261 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8100000000000000533 ) ) ; +#66262 = ORIENTED_EDGE ( 'NONE', *, *, #5720, .T. ) ; +#66263 = VECTOR ( 'NONE', #23937, 1000.000000000000000 ) ; +#66264 = FACE_OUTER_BOUND ( 'NONE', #52799, .T. ) ; +#66265 = VERTEX_POINT ( 'NONE', #42857 ) ; +#66266 = ORIENTED_EDGE ( 'NONE', *, *, #65113, .T. ) ; +#66267 = DIRECTION ( 'NONE', ( -0.7071067811865472397, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#66268 = EDGE_CURVE ( 'NONE', #88969, #11006, #82177, .T. ) ; +#66269 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87066 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6880, #85069, #6411 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66271 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#66270 = FILL_AREA_STYLE ('',( #13559 ) ) ; +#66272 = PLANE ( 'NONE', #11324 ) ; +#66273 = EDGE_CURVE ( 'NONE', #78301, #56713, #13127, .T. ) ; +#66274 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66275 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#66277 = VERTEX_POINT ( 'NONE', #74509 ) ; +#66276 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.4999999999999993339, -5.977360615245821520E-90 ) ) ; +#66278 = ORIENTED_EDGE ( 'NONE', *, *, #64665, .T. ) ; +#66279 = CARTESIAN_POINT ( 'NONE', ( -0.2919245839448350033, -1.051115598670280038, 0.8299999999999999600 ) ) ; +#66280 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66281 = ORIENTED_EDGE ( 'NONE', *, *, #2646, .T. ) ; +#66282 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.449999999999999956, -0.2000000000000000111 ) ) ; +#66283 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66284 = VERTEX_POINT ( 'NONE', #82660 ) ; +#66285 = VERTEX_POINT ( 'NONE', #3039 ) ; +#66288 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66287 = CARTESIAN_POINT ( 'NONE', ( 0.3608766233766220188, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#66286 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #27000 ) ) ; +#66289 = AXIS2_PLACEMENT_3D ( 'NONE', #69389, #8552, #30103 ) ; +#66290 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100397 ) ) ; +#66291 = LINE ( 'NONE', #97391, #99911 ) ; +#66292 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66293 = SURFACE_STYLE_USAGE ( .BOTH. , #27503 ) ; +#66294 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87300, 'distance_accuracy_value', 'NONE'); +#66295 = VERTEX_POINT ( 'NONE', #19865 ) ; +#66296 = EDGE_CURVE ( 'NONE', #93277, #43549, #51551, .T. ) ; +#66297 = FACE_OUTER_BOUND ( 'NONE', #99499, .T. ) ; +#66298 = ORIENTED_EDGE ( 'NONE', *, *, #62608, .F. ) ; +#66299 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97235 ), #48397 ) ; +#66300 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 1.600000000000000089, -13.54999999999999893 ) ) ; +#66302 = AXIS2_PLACEMENT_3D ( 'NONE', #70750, #87590, #95209 ) ; +#66301 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#66303 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#66304 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66305 = PRESENTATION_STYLE_ASSIGNMENT (( #43311 ) ) ; +#66306 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#66307 = LINE ( 'NONE', #12093, #43446 ) ; +#66308 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#66309 = EDGE_CURVE ( 'NONE', #19298, #21754, #83166, .T. ) ; +#66310 = ORIENTED_EDGE ( 'NONE', *, *, #53971, .F. ) ; +#66311 = FILL_AREA_STYLE ('',( #51009 ) ) ; +#66312 = SURFACE_STYLE_USAGE ( .BOTH. , #82636 ) ; +#66313 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#66314 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66315 = CARTESIAN_POINT ( 'NONE', ( 1.440589185038309683, -1.368586375555260526, 0.8099999999997580247 ) ) ; +#66316 = EDGE_CURVE ( 'NONE', #58149, #65802, #43208, .T. ) ; +#66317 = LINE ( 'NONE', #97897, #90734 ) ; +#66318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86252, 'distance_accuracy_value', 'NONE'); +#66319 = VECTOR ( 'NONE', #5708, 1000.000000000000000 ) ; +#66320 = FILL_AREA_STYLE ('',( #36694 ) ) ; +#66321 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66322 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66323 = EDGE_CURVE ( 'NONE', #42288, #32396, #75009, .T. ) ; +#66324 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000000104, 0.2500000000000000000 ) ) ; +#66325 = LINE ( 'NONE', #49503, #15196 ) ; +#66326 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90178 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95405, #88788, #32664 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66327 = ORIENTED_EDGE ( 'NONE', *, *, #55076, .T. ) ; +#66328 = CARTESIAN_POINT ( 'NONE', ( 1.560249861737120103, -0.9531265814360270205, 0.8100000000000000533 ) ) ; +#66329 = SURFACE_STYLE_FILL_AREA ( #12118 ) ; +#66330 = ORIENTED_EDGE ( 'NONE', *, *, #59865, .T. ) ; +#66331 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66332 = STYLED_ITEM ( 'NONE', ( #24395 ), #54746 ) ; +#66333 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66334 = VECTOR ( 'NONE', #89746, 1000.000000000000000 ) ; +#66335 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8648700000000000276 ) ) ; +#66336 = FILL_AREA_STYLE_COLOUR ( '', #61122 ) ; +#66337 = EDGE_CURVE ( 'NONE', #95742, #72731, #57707, .T. ) ; +#66338 = VECTOR ( 'NONE', #17235, 1000.000000000000000 ) ; +#66339 = FILL_AREA_STYLE ('',( #51554 ) ) ; +#66340 = ORIENTED_EDGE ( 'NONE', *, *, #57160, .F. ) ; +#66341 = EDGE_LOOP ( 'NONE', ( #41, #21918, #79282, #56172, #64948 ) ) ; +#66342 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#66343 = FILL_AREA_STYLE_COLOUR ( '', #2729 ) ; +#66344 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 7.105604999999999727, 0.8991599999999999593 ) ) ; +#66345 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66346 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66347 = AXIS2_PLACEMENT_3D ( 'NONE', #90287, #5481, #51536 ) ; +#66348 = SURFACE_SIDE_STYLE ('',( #21375 ) ) ; +#66349 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8648700000000000276 ) ) ; +#66350 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66351 = CLOSED_SHELL ( 'NONE', ( #70701, #38091, #39590, #42836, #52871, #67121 ) ) ; +#66352 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94025 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29501, #30465, #84125 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66354 = ORIENTED_EDGE ( 'NONE', *, *, #28402, .F. ) ; +#66355 = EDGE_CURVE ( 'NONE', #10670, #74640, #95438, .T. ) ; +#66356 = VECTOR ( 'NONE', #15948, 1000.000000000000000 ) ; +#66357 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000000118, -0.2500000000000000000 ) ) ; +#66358 = ORIENTED_EDGE ( 'NONE', *, *, #78556, .F. ) ; +#66359 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66360 = SURFACE_SIDE_STYLE ('',( #4064 ) ) ; +#66361 = EDGE_CURVE ( 'NONE', #46252, #43157, #20866, .T. ) ; +#66362 = CYLINDRICAL_SURFACE ( 'NONE', #12623, 0.04999999999999991257 ) ; +#66363 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66364 = CARTESIAN_POINT ( 'NONE', ( -1.102215942591399989, -0.9616422087329199453, 0.8299999999999999600 ) ) ; +#66365 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66366 = CARTESIAN_POINT ( 'NONE', ( -0.4385307926823460711, -0.9262267064097939873, 0.8299999999999999600 ) ) ; +#66367 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8100000000000000533 ) ) ; +#66368 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66370 = ORIENTED_EDGE ( 'NONE', *, *, #14988, .F. ) ; +#66369 = VERTEX_POINT ( 'NONE', #90303 ) ; +#66371 = VERTEX_POINT ( 'NONE', #97442 ) ; +#66372 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1674 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92460, #68486, #67475 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66373 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#66374 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8991599999999999593 ) ) ; +#66375 = ORIENTED_EDGE ( 'NONE', *, *, #32356, .F. ) ; +#66376 = ORIENTED_EDGE ( 'NONE', *, *, #13946, .F. ) ; +#66377 = SURFACE_STYLE_FILL_AREA ( #67847 ) ; +#66378 = ADVANCED_FACE ( 'NONE', ( #27547 ), #65315, .T. ) ; +#66379 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#66380 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66381 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75982 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20882, #12136, #83186 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66382 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#66383 = ORIENTED_EDGE ( 'NONE', *, *, #65723, .F. ) ; +#66384 = ORIENTED_EDGE ( 'NONE', *, *, #46223, .T. ) ; +#66385 = PRESENTATION_STYLE_ASSIGNMENT (( #97494 ) ) ; +#66386 = ORIENTED_EDGE ( 'NONE', *, *, #66571, .T. ) ; +#66387 = ADVANCED_FACE ( 'NONE', ( #53530 ), #22363, .T. ) ; +#66388 = VECTOR ( 'NONE', #32148, 1000.000000000000000 ) ; +#66389 = EDGE_CURVE ( 'NONE', #63097, #55979, #21869, .T. ) ; +#66391 = ORIENTED_EDGE ( 'NONE', *, *, #24117, .T. ) ; +#66390 = FILL_AREA_STYLE_COLOUR ( '', #65639 ) ; +#66392 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66393 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#66394 = ORIENTED_EDGE ( 'NONE', *, *, #31819, .T. ) ; +#66395 = FILL_AREA_STYLE ('',( #33762 ) ) ; +#66396 = PLANE ( 'NONE', #34723 ) ; +#66397 = ORIENTED_EDGE ( 'NONE', *, *, #58324, .T. ) ; +#66398 = ORIENTED_EDGE ( 'NONE', *, *, #71540, .T. ) ; +#66399 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#66400 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#66401 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66402 = LINE ( 'NONE', #58777, #27050 ) ; +#66403 = FILL_AREA_STYLE_COLOUR ( '', #80257 ) ; +#66404 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.383333333333323090, 0.000000000000000000 ) ) ; +#66406 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66405 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, 0.000000000000000000 ) ) ; +#66407 = FACE_OUTER_BOUND ( 'NONE', #34878, .T. ) ; +#66408 = ORIENTED_EDGE ( 'NONE', *, *, #98870, .T. ) ; +#66409 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66410 = SURFACE_SIDE_STYLE ('',( #35308 ) ) ; +#66411 = VERTEX_POINT ( 'NONE', #67805 ) ; +#66412 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#66413 = STYLED_ITEM ( 'NONE', ( #87666 ), #40885 ) ; +#66414 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85937 ) ) ; +#66415 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1238200612200849871, -0.02000000000000000042 ) ) ; +#66416 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66418 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#66417 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2849999999999999756, 0.1399999999999965994 ) ) ; +#66419 = LINE ( 'NONE', #28133, #11128 ) ; +#66420 = PLANE ( 'NONE', #79362 ) ; +#66421 = CLOSED_SHELL ( 'NONE', ( #26490, #15020, #50928, #40147, #32062, #28472 ) ) ; +#66423 = EDGE_CURVE ( 'NONE', #73074, #79783, #83670, .T. ) ; +#66422 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66424 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95759 ), #48520 ) ; +#66425 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#66426 = FACE_OUTER_BOUND ( 'NONE', #8890, .T. ) ; +#66427 = EDGE_CURVE ( 'NONE', #60219, #100619, #23384, .T. ) ; +#66428 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#66429 = ORIENTED_EDGE ( 'NONE', *, *, #55011, .F. ) ; +#66431 = CARTESIAN_POINT ( 'NONE', ( 3.794707603699269956E-16, 1.393372100993099938, 0.8100000000000000533 ) ) ; +#66430 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441509868, -1.332102272727269998, 0.8099999999999000222 ) ) ; +#66432 = FILL_AREA_STYLE_COLOUR ( '', #30960 ) ; +#66433 = EDGE_CURVE ( 'NONE', #16380, #90468, #54023, .T. ) ; +#66434 = LINE ( 'NONE', #40965, #72975 ) ; +#66435 = EDGE_CURVE ( 'NONE', #31665, #76527, #37705, .T. ) ; +#66436 = VERTEX_POINT ( 'NONE', #15164 ) ; +#66437 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66438 = SURFACE_STYLE_FILL_AREA ( #58321 ) ; +#66439 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66440 = LINE ( 'NONE', #97558, #96641 ) ; +#66441 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8648700000000000276 ) ) ; +#66442 = FILL_AREA_STYLE_COLOUR ( '', #58434 ) ; +#66443 = AXIS2_PLACEMENT_3D ( 'NONE', #36054, #67165, #72836 ) ; +#66444 = SURFACE_STYLE_USAGE ( .BOTH. , #35344 ) ; +#66445 = FILL_AREA_STYLE_COLOUR ( '', #26033 ) ; +#66446 = EDGE_CURVE ( 'NONE', #88747, #65875, #77492, .T. ) ; +#66447 = EDGE_CURVE ( 'NONE', #88330, #20680, #69822, .T. ) ; +#66448 = DIRECTION ( 'NONE', ( 0.6668863736986208046, -0.7451594222547972546, 0.000000000000000000 ) ) ; +#66449 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66450 = EDGE_LOOP ( 'NONE', ( #22124, #81340, #49700 ) ) ; +#66451 = PRESENTATION_STYLE_ASSIGNMENT (( #83293 ) ) ; +#66452 = VERTEX_POINT ( 'NONE', #62213 ) ; +#66453 = CARTESIAN_POINT ( 'NONE', ( -0.7229898940154579901, 0.6774732877316049784, 0.8100000000000000533 ) ) ; +#66454 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59953, 'distance_accuracy_value', 'NONE'); +#66455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56169, 'distance_accuracy_value', 'NONE'); +#66456 = ADVANCED_FACE ( 'NONE', ( #13634 ), #5984, .T. ) ; +#66457 = EDGE_CURVE ( 'NONE', #74727, #15626, #16681, .T. ) ; +#66458 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66459 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65917, #4602, #81755, #66405 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66460 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66461 = SURFACE_STYLE_USAGE ( .BOTH. , #34852 ) ; +#66462 = SURFACE_STYLE_FILL_AREA ( #98516 ) ; +#66463 = ORIENTED_EDGE ( 'NONE', *, *, #19067, .T. ) ; +#66464 = SURFACE_STYLE_FILL_AREA ( #82797 ) ; +#66465 = ORIENTED_EDGE ( 'NONE', *, *, #62125, .T. ) ; +#66466 = PLANE ( 'NONE', #84 ) ; +#66467 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66468 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53426 ) ) ; +#66469 = VERTEX_POINT ( 'NONE', #23910 ) ; +#66470 = LINE ( 'NONE', #11750, #25167 ) ; +#66471 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66472 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66473 = FILL_AREA_STYLE_COLOUR ( '', #8259 ) ; +#66475 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66474 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42069 ), #97499 ) ; +#66476 = FILL_AREA_STYLE ('',( #91466 ) ) ; +#66477 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100876 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46826, #77475, #61194 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66478 = VERTEX_POINT ( 'NONE', #25925 ) ; +#66479 = SURFACE_STYLE_FILL_AREA ( #65467 ) ; +#66481 = AXIS2_PLACEMENT_3D ( 'NONE', #22109, #53264, #16941 ) ; +#66480 = PLANE ( 'NONE', #2349 ) ; +#66482 = ORIENTED_EDGE ( 'NONE', *, *, #94456, .F. ) ; +#66483 = VECTOR ( 'NONE', #10114, 1000.000000000000114 ) ; +#66484 = PRESENTATION_STYLE_ASSIGNMENT (( #81341 ) ) ; +#66485 = CLOSED_SHELL ( 'NONE', ( #32035, #77681, #78727, #87866, #5936, #45526 ) ) ; +#66486 = ORIENTED_EDGE ( 'NONE', *, *, #67533, .F. ) ; +#66487 = ORIENTED_EDGE ( 'NONE', *, *, #96450, .T. ) ; +#66488 = VECTOR ( 'NONE', #67904, 1000.000000000000000 ) ; +#66489 = AXIS2_PLACEMENT_3D ( 'NONE', #52659, #4177, #83801 ) ; +#66490 = SURFACE_STYLE_USAGE ( .BOTH. , #44982 ) ; +#66491 = CARTESIAN_POINT ( 'NONE', ( 1.715925389647680044, -0.9637996098261990552, 0.8300000000000004041 ) ) ; +#66494 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #10679, #96010, #56263, #41934 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66493 = LINE ( 'NONE', #97597, #41892 ) ; +#66492 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 8.286472999999999089, 0.8648700000000000276 ) ) ; +#66496 = ORIENTED_EDGE ( 'NONE', *, *, #59391, .T. ) ; +#66495 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38722 ), #15880 ) ; +#66498 = ORIENTED_EDGE ( 'NONE', *, *, #14768, .T. ) ; +#66497 = ORIENTED_EDGE ( 'NONE', *, *, #20341, .F. ) ; +#66499 = VERTEX_POINT ( 'NONE', #63221 ) ; +#66500 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #19779 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#66501 = EDGE_CURVE ( 'NONE', #43395, #48584, #903, .T. ) ; +#66502 = ORIENTED_EDGE ( 'NONE', *, *, #395, .F. ) ; +#66504 = VERTEX_POINT ( 'NONE', #383 ) ; +#66503 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66505 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66506 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66507 = SURFACE_STYLE_USAGE ( .BOTH. , #57898 ) ; +#66508 = LINE ( 'NONE', #67486, #48772 ) ; +#66509 = ORIENTED_EDGE ( 'NONE', *, *, #65608, .F. ) ; +#66510 = EDGE_CURVE ( 'NONE', #986, #85300, #24800, .T. ) ; +#66511 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#66512 = SURFACE_SIDE_STYLE ('',( #76675 ) ) ; +#66513 = ORIENTED_EDGE ( 'NONE', *, *, #40102, .T. ) ; +#66514 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#66515 = FILL_AREA_STYLE_COLOUR ( '', #51319 ) ; +#66516 = AXIS2_PLACEMENT_3D ( 'NONE', #73019, #71509, #3580 ) ; +#66517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19751 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97651, #51245, #10319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66518 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66519 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66520 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#66522 = SURFACE_STYLE_FILL_AREA ( #20049 ) ; +#66521 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#66523 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9377 ) ) ; +#66524 = SURFACE_SIDE_STYLE ('',( #96134 ) ) ; +#66525 = EDGE_CURVE ( 'NONE', #58491, #26569, #79021, .T. ) ; +#66526 = ORIENTED_EDGE ( 'NONE', *, *, #68140, .F. ) ; +#66527 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66528 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40644 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68091, #15466, #31315 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66529 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89414 ), #22494 ) ; +#66530 = SURFACE_SIDE_STYLE ('',( #74199 ) ) ; +#66531 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66532 = LINE ( 'NONE', #6187, #1311 ) ; +#66533 = FILL_AREA_STYLE_COLOUR ( '', #43424 ) ; +#66534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90962 ), #17614 ) ; +#66535 = EDGE_LOOP ( 'NONE', ( #97117, #95955, #78392, #42368, #5507, #36289 ) ) ; +#66536 = SURFACE_STYLE_USAGE ( .BOTH. , #74214 ) ; +#66537 = ORIENTED_EDGE ( 'NONE', *, *, #4075, .F. ) ; +#66538 = PRESENTATION_STYLE_ASSIGNMENT (( #44057 ) ) ; +#66539 = VECTOR ( 'NONE', #87912, 1000.000000000000000 ) ; +#66540 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66541 = FILL_AREA_STYLE_COLOUR ( '', #33900 ) ; +#66542 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66543 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91934 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9225, #25649, #80280 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66544 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#66545 = FILL_AREA_STYLE ('',( #4758 ) ) ; +#66546 = CLOSED_SHELL ( 'NONE', ( #84758, #89416, #46958, #44921, #18520, #55514, #80844 ) ) ; +#66547 = CARTESIAN_POINT ( 'NONE', ( 6.389045499499825809, 9.651189499499825075, 0.8991599999999999593 ) ) ; +#66548 = EDGE_CURVE ( 'NONE', #25563, #56237, #93779, .T. ) ; +#66549 = ORIENTED_EDGE ( 'NONE', *, *, #63356, .T. ) ; +#66550 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66551 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#66552 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#66553 = PRESENTATION_STYLE_ASSIGNMENT (( #73240 ) ) ; +#66554 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#66555 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.187459415584420030, 0.8099999999999863975 ) ) ; +#66556 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#66557 = SURFACE_STYLE_USAGE ( .BOTH. , #83404 ) ; +#66558 = AXIS2_PLACEMENT_3D ( 'NONE', #16776, #55646, #64784 ) ; +#66559 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66560 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66561 = FACE_OUTER_BOUND ( 'NONE', #35437, .T. ) ; +#66562 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9981, 'distance_accuracy_value', 'NONE'); +#66563 = LINE ( 'NONE', #81430, #48581 ) ; +#66564 = STYLED_ITEM ( 'NONE', ( #71295 ), #50018 ) ; +#66565 = ORIENTED_EDGE ( 'NONE', *, *, #62608, .T. ) ; +#66566 = ORIENTED_EDGE ( 'NONE', *, *, #71876, .T. ) ; +#66567 = SURFACE_STYLE_FILL_AREA ( #73259 ) ; +#66568 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43116, 'distance_accuracy_value', 'NONE'); +#66569 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99403, 'distance_accuracy_value', 'NONE'); +#66570 = STYLED_ITEM ( 'NONE', ( #80796 ), #43949 ) ; +#66571 = EDGE_CURVE ( 'NONE', #4914, #12027, #88067, .T. ) ; +#66572 = LINE ( 'NONE', #56948, #91202 ) ; +#66573 = LINE ( 'NONE', #98633, #95160 ) ; +#66574 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66575 = LINE ( 'NONE', #34964, #59322 ) ; +#66576 = LINE ( 'NONE', #65571, #42275 ) ; +#66577 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.8999999999999999112, -0.02000000000000000042 ) ) ; +#66578 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.499999999999989786, 0.1829999999999999960 ) ) ; +#66579 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#66580 = ORIENTED_EDGE ( 'NONE', *, *, #64448, .T. ) ; +#66581 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, 0.000000000000000000 ) ) ; +#66582 = SURFACE_STYLE_USAGE ( .BOTH. , #73269 ) ; +#66583 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71162, 'distance_accuracy_value', 'NONE'); +#66584 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66585 = ADVANCED_FACE ( 'NONE', ( #95301 ), #80050, .T. ) ; +#66586 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #77620, .NOT_KNOWN. ) ; +#66587 = FACE_OUTER_BOUND ( 'NONE', #32285, .T. ) ; +#66588 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63344 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33953, #42598, #72225 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66589 = ORIENTED_EDGE ( 'NONE', *, *, #56118, .F. ) ; +#66590 = ADVANCED_FACE ( 'NONE', ( #82549 ), #88201, .F. ) ; +#66591 = LINE ( 'NONE', #11874, #73974 ) ; +#66592 = STYLED_ITEM ( 'NONE', ( #17822 ), #31454 ) ; +#66593 = CARTESIAN_POINT ( 'NONE', ( 9.507386500499999116, 6.971254500500000617, 0.8991599999999999593 ) ) ; +#66594 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#66595 = ORIENTED_EDGE ( 'NONE', *, *, #97615, .F. ) ; +#66596 = AXIS2_PLACEMENT_3D ( 'NONE', #10769, #97594, #74678 ) ; +#66597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22223, 'distance_accuracy_value', 'NONE'); +#66598 = AXIS2_PLACEMENT_3D ( 'NONE', #8727, #87435, #79281 ) ; +#66599 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60155 ), #79673 ) ; +#66600 = PLANE ( 'NONE', #16534 ) ; +#66601 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66602 = VECTOR ( 'NONE', #17707, 1000.000000000000000 ) ; +#66603 = EDGE_LOOP ( 'NONE', ( #71889, #76027, #13179, #87229 ) ) ; +#66604 = FILL_AREA_STYLE_COLOUR ( '', #90498 ) ; +#66605 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66606 = FILL_AREA_STYLE ('',( #19649 ) ) ; +#66607 = CARTESIAN_POINT ( 'NONE', ( -1.117273754646370687, -1.233175053557125977, 0.8099999999998163114 ) ) ; +#66608 = LINE ( 'NONE', #96225, #92363 ) ; +#66609 = ORIENTED_EDGE ( 'NONE', *, *, #77280, .F. ) ; +#66610 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.416666666666666519, 0.000000000000000000 ) ) ; +#66611 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64715 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76550, #30081, #53596 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66612 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86710 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23133, #13894, #53267 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66613 = AXIS2_PLACEMENT_3D ( 'NONE', #82008, #66650, #90132 ) ; +#66614 = ORIENTED_EDGE ( 'NONE', *, *, #49408, .T. ) ; +#66616 = ORIENTED_EDGE ( 'NONE', *, *, #58223, .F. ) ; +#66615 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999989964, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#66617 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000637737685, -0.6999999999948158802 ) ) ; +#66618 = SURFACE_STYLE_FILL_AREA ( #3344 ) ; +#66619 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.8999999999999990230, 0.1829999999999829818 ) ) ; +#66621 = EDGE_CURVE ( 'NONE', #63866, #23290, #57580, .T. ) ; +#66620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66622 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#66623 = ORIENTED_EDGE ( 'NONE', *, *, #83298, .T. ) ; +#66624 = CARTESIAN_POINT ( 'NONE', ( 1.289608948985750070, -1.506193478032149979, 0.8299999999999999600 ) ) ; +#66625 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66626 = PLANE ( 'NONE', #62998 ) ; +#66627 = ORIENTED_EDGE ( 'NONE', *, *, #34972, .T. ) ; +#66628 = AXIS2_PLACEMENT_3D ( 'NONE', #53496, #38660, #69787 ) ; +#66630 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#66629 = LINE ( 'NONE', #97729, #52033 ) ; +#66631 = VERTEX_POINT ( 'NONE', #90184 ) ; +#66632 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99126 ) ) ; +#66633 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66634 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#66635 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#66636 = EDGE_LOOP ( 'NONE', ( #91393, #54557, #1178, #65264 ) ) ; +#66637 = CARTESIAN_POINT ( 'NONE', ( -0.2757359312880713342, 0.8200000000000000622, -0.1378679656440357226 ) ) ; +#66638 = VERTEX_POINT ( 'NONE', #2930 ) ; +#66639 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 1.149999999999999911, 0.000000000000000000 ) ) ; +#66640 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#66641 = CARTESIAN_POINT ( 'NONE', ( -1.078436373535740067, -1.243129529655299992, 0.8100000000000000533 ) ) ; +#66642 = SURFACE_STYLE_FILL_AREA ( #91143 ) ; +#66643 = SURFACE_STYLE_FILL_AREA ( #71455 ) ; +#66644 = VECTOR ( 'NONE', #100349, 1000.000000000000000 ) ; +#66645 = CARTESIAN_POINT ( 'NONE', ( -0.6674107142857141906, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#66646 = FACE_OUTER_BOUND ( 'NONE', #55990, .T. ) ; +#66648 = ADVANCED_FACE ( 'NONE', ( #96317 ), #12502, .F. ) ; +#66647 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.09999999999999870104, -9.095983544939292593E-90 ) ) ; +#66649 = SURFACE_SIDE_STYLE ('',( #18671 ) ) ; +#66650 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66651 = FILL_AREA_STYLE ('',( #58044 ) ) ; +#66652 = STYLED_ITEM ( 'NONE', ( #5511 ), #92571 ) ; +#66653 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66654 = ORIENTED_EDGE ( 'NONE', *, *, #46719, .T. ) ; +#66655 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#66656 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66658 = SURFACE_STYLE_FILL_AREA ( #20703 ) ; +#66657 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#66659 = VECTOR ( 'NONE', #26085, 1000.000000000000000 ) ; +#66660 = FILL_AREA_STYLE ('',( #59057 ) ) ; +#66661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66662 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76424 ), #89569 ) ; +#66663 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, 1.600000000000000089, -11.41999999999999993 ) ) ; +#66664 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66665 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66666 = EDGE_CURVE ( 'NONE', #10422, #38892, #80547, .T. ) ; +#66668 = VERTEX_POINT ( 'NONE', #36095 ) ; +#66667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50401 ), #24300 ) ; +#66669 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#66670 = FACE_OUTER_BOUND ( 'NONE', #54067, .T. ) ; +#66671 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#66672 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2808578643762690841, 0.1499999999999999667 ) ) ; +#66673 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#66674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66675 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #80710, #26577, #88346, #43383 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66676 = PLANE ( 'NONE', #99 ) ; +#66677 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66678 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#66679 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60175 ) ) ; +#66680 = LINE ( 'NONE', #19204, #35981 ) ; +#66681 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.000000000000000000 ) ) ; +#66682 = STYLED_ITEM ( 'NONE', ( #25173 ), #63583 ) ; +#66683 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66684 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66685 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66687 = EDGE_CURVE ( 'NONE', #62491, #40128, #49913, .T. ) ; +#66686 = FACE_OUTER_BOUND ( 'NONE', #42255, .T. ) ; +#66688 = PRESENTATION_STYLE_ASSIGNMENT (( #12487 ) ) ; +#66689 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87060, 'distance_accuracy_value', 'NONE'); +#66690 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#66691 = CARTESIAN_POINT ( 'NONE', ( 8.665929124874956813, 3.159949124874956272, 0.8648700000000000276 ) ) ; +#66692 = VECTOR ( 'NONE', #54751, 1000.000000000000000 ) ; +#66693 = PRESENTATION_STYLE_ASSIGNMENT (( #83037 ) ) ; +#66694 = ORIENTED_EDGE ( 'NONE', *, *, #94555, .F. ) ; +#66695 = SURFACE_STYLE_FILL_AREA ( #35596 ) ; +#66696 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32026, 'distance_accuracy_value', 'NONE'); +#66697 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90871, 'distance_accuracy_value', 'NONE'); +#66698 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#66699 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66700 = FILL_AREA_STYLE_COLOUR ( '', #55702 ) ; +#66701 = VECTOR ( 'NONE', #75858, 1000.000000000000000 ) ; +#66702 = ADVANCED_FACE ( 'NONE', ( #39451 ), #39971, .T. ) ; +#66703 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999988010, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#66704 = ORIENTED_EDGE ( 'NONE', *, *, #47434, .T. ) ; +#66705 = SURFACE_STYLE_FILL_AREA ( #51920 ) ; +#66706 = ORIENTED_EDGE ( 'NONE', *, *, #23646, .T. ) ; +#66707 = FILL_AREA_STYLE_COLOUR ( '', #29287 ) ; +#66708 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27359, 'distance_accuracy_value', 'NONE'); +#66709 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, 0.2999999999999991562, -0.02000000000000000042 ) ) ; +#66710 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97534, 'distance_accuracy_value', 'NONE'); +#66711 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66712 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66713 = LINE ( 'NONE', #91693, #95830 ) ; +#66714 = VERTEX_POINT ( 'NONE', #78762 ) ; +#66715 = EDGE_LOOP ( 'NONE', ( #90373, #8587, #14976, #4785 ) ) ; +#66716 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66717 = ORIENTED_EDGE ( 'NONE', *, *, #52544, .T. ) ; +#66718 = CARTESIAN_POINT ( 'NONE', ( 1.769821822789199972, -1.235192314287260062, 0.8100000000000000533 ) ) ; +#66719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83067 ), #47120 ) ; +#66720 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#66721 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66722 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.100000000000000089, 1.048695503451053346E-76 ) ) ; +#66723 = SURFACE_STYLE_FILL_AREA ( #96844 ) ; +#66724 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66725 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#66726 = EDGE_CURVE ( 'NONE', #37746, #60625, #37961, .T. ) ; +#66728 = EDGE_LOOP ( 'NONE', ( #68210, #57519, #1338, #37762 ) ) ; +#66727 = ORIENTED_EDGE ( 'NONE', *, *, #37197, .F. ) ; +#66729 = ORIENTED_EDGE ( 'NONE', *, *, #65678, .F. ) ; +#66730 = ORIENTED_EDGE ( 'NONE', *, *, #27250, .F. ) ; +#66731 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66732 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37093 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83421, #68567, #69042 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66734 = CARTESIAN_POINT ( 'NONE', ( 1.283545161422839920, -0.8955552045491329549, 0.8299999999999999600 ) ) ; +#66733 = CARTESIAN_POINT ( 'NONE', ( 0.3795945119668320267, -0.9004463214819089512, 0.8299999999999999600 ) ) ; +#66735 = ORIENTED_EDGE ( 'NONE', *, *, #5821, .T. ) ; +#66736 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89331 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98262, #59588, #27399 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66737 = EDGE_CURVE ( 'NONE', #35982, #27223, #46069, .T. ) ; +#66738 = AXIS2_PLACEMENT_3D ( 'NONE', #5791, #60490, #91591 ) ; +#66739 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3136 ) ) ; +#66740 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66741 = PRESENTATION_STYLE_ASSIGNMENT (( #35642 ) ) ; +#66742 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37409 ), #34214 ) ; +#66743 = SURFACE_SIDE_STYLE ('',( #58634 ) ) ; +#66744 = ORIENTED_EDGE ( 'NONE', *, *, #62414, .F. ) ; +#66745 = SURFACE_STYLE_USAGE ( .BOTH. , #59652 ) ; +#66746 = VERTEX_POINT ( 'NONE', #85413 ) ; +#66747 = ORIENTED_EDGE ( 'NONE', *, *, #9378, .F. ) ; +#66748 = CARTESIAN_POINT ( 'NONE', ( 1.070634376467239912, -1.188596174736179956, 0.8299999999999999600 ) ) ; +#66750 = LINE ( 'NONE', #19803, #35284 ) ; +#66749 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66751 = VECTOR ( 'NONE', #4004, 1000.000000000000000 ) ; +#66752 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 2.175017978223169360E-17, -0.6500000000000000222 ) ) ; +#66753 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35697 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13098, #88785, #83138 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66754 = PRESENTATION_STYLE_ASSIGNMENT (( #55116 ) ) ; +#66755 = EDGE_LOOP ( 'NONE', ( #66951, #65246, #56102, #49832 ) ) ; +#66757 = AXIS2_PLACEMENT_3D ( 'NONE', #78768, #25193, #87439 ) ; +#66756 = LINE ( 'NONE', #90754, #12314 ) ; +#66758 = ORIENTED_EDGE ( 'NONE', *, *, #53384, .T. ) ; +#66759 = FACE_OUTER_BOUND ( 'NONE', #95005, .T. ) ; +#66760 = ORIENTED_EDGE ( 'NONE', *, *, #66985, .T. ) ; +#66761 = SURFACE_SIDE_STYLE ('',( #51977 ) ) ; +#66762 = ORIENTED_EDGE ( 'NONE', *, *, #92971, .T. ) ; +#66763 = EDGE_LOOP ( 'NONE', ( #91213, #81321, #79497, #19396 ) ) ; +#66764 = PRESENTATION_STYLE_ASSIGNMENT (( #73948 ) ) ; +#66765 = SURFACE_SIDE_STYLE ('',( #89269 ) ) ; +#66766 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2761799387799150352, 0.000000000000000000 ) ) ; +#66767 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66768 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66769 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000533, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#66770 = FILL_AREA_STYLE_COLOUR ( '', #46202 ) ; +#66771 = EDGE_CURVE ( 'NONE', #26125, #81873, #7226, .T. ) ; +#66773 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#66772 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24401 ), #52156 ) ; +#66774 = FILL_AREA_STYLE ('',( #41812 ) ) ; +#66775 = ORIENTED_EDGE ( 'NONE', *, *, #46221, .T. ) ; +#66776 = FILL_AREA_STYLE_COLOUR ( '', #61090 ) ; +#66777 = EDGE_LOOP ( 'NONE', ( #75325, #41277, #31094, #34278 ) ) ; +#66778 = CARTESIAN_POINT ( 'NONE', ( 11.67113275025008789, 7.282382249749913328, 0.8648700000000000276 ) ) ; +#66779 = PRESENTATION_STYLE_ASSIGNMENT (( #90270 ) ) ; +#66780 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17871 ) ) ; +#66781 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66782 = LINE ( 'NONE', #26504, #15354 ) ; +#66783 = FACE_OUTER_BOUND ( 'NONE', #36159, .T. ) ; +#66784 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66785 = FILL_AREA_STYLE ('',( #84492 ) ) ; +#66786 = SURFACE_SIDE_STYLE ('',( #50514 ) ) ; +#66787 = LINE ( 'NONE', #4987, #48374 ) ; +#66788 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66789 = EDGE_CURVE ( 'NONE', #28081, #68842, #56449, .T. ) ; +#66790 = EDGE_LOOP ( 'NONE', ( #14684, #65244, #38691, #61632, #99612, #95613, #18198, #9463 ) ) ; +#66791 = ADVANCED_FACE ( 'NONE', ( #93538 ), #45557, .T. ) ; +#66792 = SURFACE_STYLE_FILL_AREA ( #11588 ) ; +#66793 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8648700000000000276 ) ) ; +#66794 = CARTESIAN_POINT ( 'NONE', ( 0.2295068781666219915, -0.9459922548521020325, 0.8100000000000000533 ) ) ; +#66795 = LINE ( 'NONE', #27023, #78933 ) ; +#66796 = FILL_AREA_STYLE_COLOUR ( '', #4357 ) ; +#66797 = VECTOR ( 'NONE', #14918, 1000.000000000000000 ) ; +#66798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66799 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#66800 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66801 = FACE_OUTER_BOUND ( 'NONE', #67551, .T. ) ; +#66802 = VECTOR ( 'NONE', #24977, 1000.000000000000000 ) ; +#66803 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 2.544766999999999779, 0.8991599999999999593 ) ) ; +#66804 = FILL_AREA_STYLE ('',( #28034 ) ) ; +#66805 = PRESENTATION_STYLE_ASSIGNMENT (( #53017 ) ) ; +#66806 = FACE_OUTER_BOUND ( 'NONE', #79684, .T. ) ; +#66807 = PRESENTATION_STYLE_ASSIGNMENT (( #98869 ) ) ; +#66808 = AXIS2_PLACEMENT_3D ( 'NONE', #13301, #44505, #75669 ) ; +#66809 = VECTOR ( 'NONE', #52312, 1000.000000000000000 ) ; +#66810 = ADVANCED_FACE ( 'NONE', ( #69048 ), #32314, .F. ) ; +#66811 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51165, 'distance_accuracy_value', 'NONE'); +#66812 = ORIENTED_EDGE ( 'NONE', *, *, #30959, .F. ) ; +#66813 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1499999999999999667, -3.009265538105054994E-33 ) ) ; +#66814 = CYLINDRICAL_SURFACE ( 'NONE', #53622, 0.1000000000000000194 ) ; +#66815 = FILL_AREA_STYLE_COLOUR ( '', #50810 ) ; +#66816 = VERTEX_POINT ( 'NONE', #49155 ) ; +#66817 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#66818 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66819 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66820 = EDGE_CURVE ( 'NONE', #37111, #21167, #57329, .T. ) ; +#66821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22807 ) ) ; +#66822 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, -0.02000000000000000042 ) ) ; +#66823 = FILL_AREA_STYLE ('',( #66336 ) ) ; +#66824 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#66825 = EDGE_CURVE ( 'NONE', #77646, #95367, #56833, .T. ) ; +#66826 = SURFACE_STYLE_FILL_AREA ( #66339 ) ; +#66827 = EDGE_LOOP ( 'NONE', ( #58478, #40084, #56370, #39882 ) ) ; +#66828 = EDGE_CURVE ( 'NONE', #9989, #26971, #33838, .T. ) ; +#66829 = VERTEX_POINT ( 'NONE', #87936 ) ; +#66830 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66831 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 3.435721000000000025, 0.8991599999999999593 ) ) ; +#66832 = STYLED_ITEM ( 'NONE', ( #81123 ), #75707 ) ; +#66833 = PLANE ( 'NONE', #85560 ) ; +#66834 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66835 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441509868, -1.332102272727269998, 0.8099999999999000222 ) ) ; +#66836 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63817, 'distance_accuracy_value', 'NONE'); +#66837 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#66838 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40992, 'distance_accuracy_value', 'NONE'); +#66839 = SURFACE_STYLE_USAGE ( .BOTH. , #29051 ) ; +#66840 = SURFACE_STYLE_USAGE ( .BOTH. , #35733 ) ; +#66841 = SURFACE_STYLE_FILL_AREA ( #52052 ) ; +#66842 = PRESENTATION_STYLE_ASSIGNMENT (( #60231 ) ) ; +#66843 = ORIENTED_EDGE ( 'NONE', *, *, #75727, .F. ) ; +#66844 = SURFACE_SIDE_STYLE ('',( #68823 ) ) ; +#66845 = ORIENTED_EDGE ( 'NONE', *, *, #23279, .T. ) ; +#66847 = PRESENTATION_STYLE_ASSIGNMENT (( #51060 ) ) ; +#66846 = STYLED_ITEM ( 'NONE', ( #27029 ), #51237 ) ; +#66848 = SURFACE_STYLE_USAGE ( .BOTH. , #35743 ) ; +#66849 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -9.880000000000000782, 0.2499999999999999445 ) ) ; +#66850 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#66851 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#66852 = FILL_AREA_STYLE ('',( #34742 ) ) ; +#66853 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#66854 = EDGE_CURVE ( 'NONE', #26074, #51814, #18479, .T. ) ; +#66855 = CARTESIAN_POINT ( 'NONE', ( -1.269090901571400032, -0.9900689134305360461, 0.8100000000000000533 ) ) ; +#66857 = ORIENTED_EDGE ( 'NONE', *, *, #90787, .T. ) ; +#66856 = VERTEX_POINT ( 'NONE', #40493 ) ; +#66858 = ORIENTED_EDGE ( 'NONE', *, *, #40297, .F. ) ; +#66859 = SURFACE_SIDE_STYLE ('',( #12678 ) ) ; +#66860 = SURFACE_STYLE_USAGE ( .BOTH. , #2583 ) ; +#66861 = ORIENTED_EDGE ( 'NONE', *, *, #3427, .T. ) ; +#66862 = EDGE_CURVE ( 'NONE', #39930, #58022, #24684, .T. ) ; +#66863 = EDGE_LOOP ( 'NONE', ( #44758, #5823, #35491, #96488 ) ) ; +#66864 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#66865 = PRESENTATION_STYLE_ASSIGNMENT (( #51085 ) ) ; +#66867 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8299999999999999600 ) ) ; +#66866 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66868 = ORIENTED_EDGE ( 'NONE', *, *, #20769, .F. ) ; +#66869 = ADVANCED_FACE ( 'NONE', ( #41001 ), #25186, .T. ) ; +#66870 = VERTEX_POINT ( 'NONE', #3175 ) ; +#66871 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76557, #84238, #31115, #15764 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66872 = ORIENTED_EDGE ( 'NONE', *, *, #72595, .T. ) ; +#66873 = LINE ( 'NONE', #97958, #2070 ) ; +#66874 = VECTOR ( 'NONE', #39638, 1000.000000000000000 ) ; +#66875 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37598 ), #27771 ) ; +#66876 = AXIS2_PLACEMENT_3D ( 'NONE', #69397, #31139, #54646 ) ; +#66877 = EDGE_CURVE ( 'NONE', #55806, #37870, #49194, .T. ) ; +#66878 = STYLED_ITEM ( 'NONE', ( #72406 ), #57613 ) ; +#66880 = ORIENTED_EDGE ( 'NONE', *, *, #27418, .T. ) ; +#66879 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66881 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9738 ), #39185 ) ; +#66882 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999992895, 3.500000000000000444, -1.195472123049164304E-89 ) ) ; +#66883 = VERTEX_POINT ( 'NONE', #86680 ) ; +#66884 = AXIS2_PLACEMENT_3D ( 'NONE', #30447, #21816, #14111 ) ; +#66885 = CARTESIAN_POINT ( 'NONE', ( -0.04841281441248360129, -1.230342595016630014, 0.8100000000000000533 ) ) ; +#66886 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#66887 = EDGE_LOOP ( 'NONE', ( #99551, #41827, #63471, #8461 ) ) ; +#66888 = VERTEX_POINT ( 'NONE', #85151 ) ; +#66889 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999512, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#66890 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#66891 = CIRCLE ( 'NONE', #88123, 0.9754790742981810370 ) ; +#66892 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#66893 = AXIS2_PLACEMENT_3D ( 'NONE', #12984, #5857, #83524 ) ; +#66894 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66895 = ADVANCED_FACE ( 'NONE', ( #8989 ), #93783, .F. ) ; +#66896 = SURFACE_STYLE_FILL_AREA ( #89386 ) ; +#66897 = SURFACE_SIDE_STYLE ('',( #50616 ) ) ; +#66898 = CARTESIAN_POINT ( 'NONE', ( 1.540061115671039982, -0.9808836469697840288, 0.8299999999999997380 ) ) ; +#66899 = ORIENTED_EDGE ( 'NONE', *, *, #88165, .T. ) ; +#66900 = PRESENTATION_STYLE_ASSIGNMENT (( #35804 ) ) ; +#66901 = AXIS2_PLACEMENT_3D ( 'NONE', #55912, #63574, #56926 ) ; +#66902 = SURFACE_STYLE_FILL_AREA ( #98955 ) ; +#66903 = VERTEX_POINT ( 'NONE', #46844 ) ; +#66904 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3161 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27978, #36136, #65763 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66905 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66906 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66907 = CARTESIAN_POINT ( 'NONE', ( -0.2912322945111979755, -1.413990021526319918, 0.8299999999999999600 ) ) ; +#66908 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#66909 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4808578643762691507, 0.2499999999999999722 ) ) ; +#66910 = CARTESIAN_POINT ( 'NONE', ( 1.429289321881345165, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#66911 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66912 = SURFACE_STYLE_FILL_AREA ( #96025 ) ; +#66913 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998900047, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#66914 = FACE_OUTER_BOUND ( 'NONE', #93795, .T. ) ; +#66915 = ADVANCED_FACE ( 'NONE', ( #32572 ), #87187, .T. ) ; +#66916 = EDGE_CURVE ( 'NONE', #98041, #93065, #78505, .T. ) ; +#66917 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64102 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42277, #34629, #56616 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66918 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66919 = STYLED_ITEM ( 'NONE', ( #48881 ), #51384 ) ; +#66920 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#66921 = AXIS2_PLACEMENT_3D ( 'NONE', #43702, #20734, #81045 ) ; +#66922 = VERTEX_POINT ( 'NONE', #71356 ) ; +#66923 = LINE ( 'NONE', #81776, #61914 ) ; +#66925 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66924 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66926 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, 1.449999999999999956, -11.41999999999999993 ) ) ; +#66928 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1035 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15316, #95453, #8107 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66927 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66929 = EDGE_CURVE ( 'NONE', #41762, #56862, #17218, .T. ) ; +#66930 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29231, 'distance_accuracy_value', 'NONE'); +#66931 = ORIENTED_EDGE ( 'NONE', *, *, #78101, .F. ) ; +#66932 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.7000000000000000666, -0.02000000000000000042 ) ) ; +#66933 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#66934 = CARTESIAN_POINT ( 'NONE', ( 0.5833333333333340365, -3.099999999999980549, 0.000000000000000000 ) ) ; +#66935 = LINE ( 'NONE', #89423, #31437 ) ; +#66936 = ADVANCED_FACE ( 'NONE', ( #88204 ), #96320, .T. ) ; +#66937 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66938 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#66939 = STYLED_ITEM ( 'NONE', ( #81519 ), #18122 ) ; +#66940 = SURFACE_STYLE_FILL_AREA ( #36318 ) ; +#66941 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20736 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100741, #70216, #69176 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66942 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#66943 = LINE ( 'NONE', #28160, #13733 ) ; +#66944 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #52480, #92257 ), + ( #14620, #93736 ), + ( #5943, #45764 ), + ( #100313, #30453 ), + ( #38652, #99342 ), + ( #69775, #100803 ), + ( #30987, #62166 ), + ( #77961, #29486 ), + ( #7922, #39149 ), + ( #9446, #78460 ), + ( #33535, #9930 ), + ( #65155, #8420 ), + ( #94760, #55518 ), + ( #86624, #79493 ), + ( #48852, #64658 ), + ( #8933, #2887 ), + ( #40181, #49339 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06966389745086019880, 0.1364315478428499984, 0.2011873724129779883, 0.2645983123399129888, 0.3259037851543969966, 0.3855761511408299924, 0.4444834551525079780, 0.5032708546699640184, 0.5621995445251519730, 0.6211282343803400385, 0.6821163697534160519, 0.7443520026810309664, 0.8704105427126580530, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#66945 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1301 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #704, #78825, #94631 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66946 = EDGE_CURVE ( 'NONE', #32313, #99432, #96821, .T. ) ; +#66947 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79250 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82154, #59702, #66798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66948 = SURFACE_STYLE_USAGE ( .BOTH. , #59342 ) ; +#66949 = ORIENTED_EDGE ( 'NONE', *, *, #34057, .F. ) ; +#66950 = EDGE_CURVE ( 'NONE', #51794, #28082, #47725, .T. ) ; +#66951 = ORIENTED_EDGE ( 'NONE', *, *, #36161, .F. ) ; +#66952 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50232, 'distance_accuracy_value', 'NONE'); +#66953 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92994 ) ) ; +#66954 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#66955 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#66956 = VECTOR ( 'NONE', #30853, 1000.000000000000000 ) ; +#66957 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#66958 = SURFACE_SIDE_STYLE ('',( #98512 ) ) ; +#66959 = SURFACE_STYLE_USAGE ( .BOTH. , #83800 ) ; +#66960 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#66961 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000053513, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#66962 = FACE_OUTER_BOUND ( 'NONE', #98904, .T. ) ; +#66963 = VERTEX_POINT ( 'NONE', #3444 ) ; +#66964 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999999778, 3.123820061220055511, 0.000000000000000000 ) ) ; +#66965 = SURFACE_STYLE_USAGE ( .BOTH. , #89457 ) ; +#66966 = STYLED_ITEM ( 'NONE', ( #72384 ), #6832 ) ; +#66967 = VERTEX_POINT ( 'NONE', #95819 ) ; +#66968 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#66969 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51262, #75722, #75245 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66970 = ORIENTED_EDGE ( 'NONE', *, *, #55866, .T. ) ; +#66971 = FILL_AREA_STYLE_COLOUR ( '', #50200 ) ; +#66972 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52276 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30338, #77324, #92621 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66973 = PLANE ( 'NONE', #34476 ) ; +#66974 = EDGE_CURVE ( 'NONE', #57020, #46504, #82061, .T. ) ; +#66975 = PLANE ( 'NONE', #28395 ) ; +#66976 = AXIS2_PLACEMENT_3D ( 'NONE', #83887, #37445, #13880 ) ; +#66977 = ORIENTED_EDGE ( 'NONE', *, *, #54825, .T. ) ; +#66978 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83164 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23820, #817, #33504 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66979 = FILL_AREA_STYLE_COLOUR ( '', #3339 ) ; +#66980 = FILL_AREA_STYLE_COLOUR ( '', #85408 ) ; +#66981 = ORIENTED_EDGE ( 'NONE', *, *, #56097, .F. ) ; +#66982 = FILL_AREA_STYLE_COLOUR ( '', #39440 ) ; +#66983 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -13.35000000000000142 ) ) ; +#66984 = VERTEX_POINT ( 'NONE', #18205 ) ; +#66985 = EDGE_CURVE ( 'NONE', #39620, #94240, #41739, .T. ) ; +#66986 = ORIENTED_EDGE ( 'NONE', *, *, #44639, .F. ) ; +#66987 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#66988 = FACE_OUTER_BOUND ( 'NONE', #16249, .T. ) ; +#66989 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42968 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37079, #68673, #22742 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#66991 = SURFACE_SIDE_STYLE ('',( #57886 ) ) ; +#66990 = LINE ( 'NONE', #68970, #52932 ) ; +#66992 = ORIENTED_EDGE ( 'NONE', *, *, #48437, .F. ) ; +#66993 = EDGE_CURVE ( 'NONE', #21671, #31057, #11998, .T. ) ; +#66994 = ORIENTED_EDGE ( 'NONE', *, *, #46853, .T. ) ; +#66995 = ORIENTED_EDGE ( 'NONE', *, *, #94236, .T. ) ; +#66996 = VECTOR ( 'NONE', #92488, 1000.000000000000000 ) ; +#66997 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, 0.1400000000000000133 ) ) ; +#66998 = EDGE_CURVE ( 'NONE', #97350, #66371, #64707, .T. ) ; +#66999 = VECTOR ( 'NONE', #97334, 1000.000000000000000 ) ; +#67001 = EDGE_LOOP ( 'NONE', ( #42256, #18141, #61131, #40941 ) ) ; +#67000 = SURFACE_STYLE_USAGE ( .BOTH. , #43511 ) ; +#67002 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#67003 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.4245906043549200204, -6.018531076210109988E-33 ) ) ; +#67004 = SURFACE_STYLE_FILL_AREA ( #97609 ) ; +#67005 = VERTEX_POINT ( 'NONE', #49395 ) ; +#67006 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67007 = FACE_OUTER_BOUND ( 'NONE', #17017, .T. ) ; +#67008 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67009 = VERTEX_POINT ( 'NONE', #26419 ) ; +#67010 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#67011 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67012 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8299999999999999600 ) ) ; +#67013 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67014 = AXIS2_PLACEMENT_3D ( 'NONE', #50192, #57339, #1699 ) ; +#67015 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#67017 = ADVANCED_FACE ( 'NONE', ( #97323 ), #10992, .F. ) ; +#67016 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.000000000000000000 ) ) ; +#67018 = EDGE_CURVE ( 'NONE', #73661, #56748, #75374, .T. ) ; +#67019 = VECTOR ( 'NONE', #47560, 1000.000000000000000 ) ; +#67020 = SURFACE_STYLE_USAGE ( .BOTH. , #43530 ) ; +#67021 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67022 = CARTESIAN_POINT ( 'NONE', ( 1.498514669629020135, -1.357596283920579960, 0.8299999999999999600 ) ) ; +#67023 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373193000000000552, 0.8991599999999999593 ) ) ; +#67024 = SURFACE_STYLE_FILL_AREA ( #21078 ) ; +#67025 = ORIENTED_EDGE ( 'NONE', *, *, #61109, .F. ) ; +#67026 = VECTOR ( 'NONE', #30975, 1000.000000000000000 ) ; +#67027 = FILL_AREA_STYLE ('',( #20557 ) ) ; +#67028 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#67029 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89417 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24123, #15904, #69014 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67030 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67032 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67031 = LINE ( 'NONE', #80876, #29881 ) ; +#67033 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#67034 = LINE ( 'NONE', #58918, #98739 ) ; +#67035 = EDGE_CURVE ( 'NONE', #2575, #91087, #74883, .T. ) ; +#67036 = LINE ( 'NONE', #20061, #85082 ) ; +#67037 = VECTOR ( 'NONE', #9725, 1000.000000000000000 ) ; +#67038 = VERTEX_POINT ( 'NONE', #52413 ) ; +#67039 = ADVANCED_FACE ( 'NONE', ( #67207 ), #44709, .T. ) ; +#67040 = LINE ( 'NONE', #67519, #33255 ) ; +#67041 = FILL_AREA_STYLE_COLOUR ( '', #36952 ) ; +#67042 = ORIENTED_EDGE ( 'NONE', *, *, #95193, .T. ) ; +#67043 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67044 = CIRCLE ( 'NONE', #23041, 0.6500000000000001332 ) ; +#67045 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.000000000000000000 ) ) ; +#67046 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44224 ), #47512 ) ; +#67047 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67048 = SURFACE_SIDE_STYLE ('',( #37437 ) ) ; +#67049 = VECTOR ( 'NONE', #94987, 1000.000000000000000 ) ; +#67050 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8991599999999999593 ) ) ; +#67051 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67052 = EDGE_LOOP ( 'NONE', ( #58883, #36753, #50258, #40921 ) ) ; +#67053 = LINE ( 'NONE', #4761, #29379 ) ; +#67054 = LINE ( 'NONE', #66066, #44088 ) ; +#67055 = PLANE ( 'NONE', #80363 ) ; +#67056 = LINE ( 'NONE', #73242, #43622 ) ; +#67057 = LINE ( 'NONE', #30243, #63229 ) ; +#67058 = FACE_OUTER_BOUND ( 'NONE', #7739, .T. ) ; +#67059 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9902 ) ) ; +#67061 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #48076, #95000, #86365, #72550 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67060 = LINE ( 'NONE', #98136, #53419 ) ; +#67062 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67063 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67064 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67065 = LINE ( 'NONE', #19603, #77845 ) ; +#67066 = DIRECTION ( 'NONE', ( -0.9312650831180608879, 0.000000000000000000, 0.3643423458302799678 ) ) ; +#67067 = ORIENTED_EDGE ( 'NONE', *, *, #55880, .T. ) ; +#67068 = LINE ( 'NONE', #36448, #28517 ) ; +#67069 = EDGE_CURVE ( 'NONE', #63753, #14732, #14043, .T. ) ; +#67070 = EDGE_LOOP ( 'NONE', ( #64341, #12641, #89324, #80795 ) ) ; +#67071 = VECTOR ( 'NONE', #30926, 1000.000000000000000 ) ; +#67072 = SURFACE_STYLE_FILL_AREA ( #21617 ) ; +#67073 = LINE ( 'NONE', #58963, #11942 ) ; +#67074 = FILL_AREA_STYLE_COLOUR ( '', #76997 ) ; +#67075 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 7.826853999999999090, 0.8648700000000000276 ) ) ; +#67076 = FILL_AREA_STYLE_COLOUR ( '', #10093 ) ; +#67077 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#67079 = EDGE_CURVE ( 'NONE', #98020, #31163, #36599, .T. ) ; +#67078 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#67080 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#67081 = ORIENTED_EDGE ( 'NONE', *, *, #99516, .F. ) ; +#67082 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, 0.000000000000000000 ) ) ; +#67083 = FACE_OUTER_BOUND ( 'NONE', #97510, .T. ) ; +#67084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80063 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54236, #81273, #11197 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67085 = STYLED_ITEM ( 'NONE', ( #13269 ), #33903 ) ; +#67086 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#67087 = VERTEX_POINT ( 'NONE', #53404 ) ; +#67088 = LINE ( 'NONE', #68581, #38710 ) ; +#67089 = FILL_AREA_STYLE_COLOUR ( '', #16862 ) ; +#67090 = FILL_AREA_STYLE_COLOUR ( '', #53811 ) ; +#67091 = ADVANCED_FACE ( 'NONE', ( #98777 ), #68696, .T. ) ; +#67092 = SURFACE_STYLE_USAGE ( .BOTH. , #90590 ) ; +#67093 = ORIENTED_EDGE ( 'NONE', *, *, #16798, .T. ) ; +#67094 = SURFACE_SIDE_STYLE ('',( #73768 ) ) ; +#67095 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #257 ), #34489 ) ; +#67096 = SURFACE_SIDE_STYLE ('',( #75279 ) ) ; +#67097 = STYLED_ITEM ( 'NONE', ( #42196 ), #8186 ) ; +#67098 = SURFACE_SIDE_STYLE ('',( #37977 ) ) ; +#67099 = SURFACE_SIDE_STYLE ('',( #90082 ) ) ; +#67100 = LINE ( 'NONE', #36983, #67975 ) ; +#67101 = EDGE_CURVE ( 'NONE', #5636, #88325, #15044, .T. ) ; +#67102 = ORIENTED_EDGE ( 'NONE', *, *, #30812, .T. ) ; +#67103 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67104 = LINE ( 'NONE', #20641, #65216 ) ; +#67105 = CARTESIAN_POINT ( 'NONE', ( -1.198405638302102227, -1.214867104881772075, 0.8099999999998298561 ) ) ; +#67106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19887 ), #14945 ) ; +#67107 = ORIENTED_EDGE ( 'NONE', *, *, #93678, .F. ) ; +#67108 = FACE_OUTER_BOUND ( 'NONE', #35411, .T. ) ; +#67109 = EDGE_CURVE ( 'NONE', #78546, #88447, #24309, .T. ) ; +#67110 = VECTOR ( 'NONE', #58013, 1000.000000000000000 ) ; +#67111 = VERTEX_POINT ( 'NONE', #16577 ) ; +#67113 = ORIENTED_EDGE ( 'NONE', *, *, #89306, .T. ) ; +#67112 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#67114 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23460, 'distance_accuracy_value', 'NONE'); +#67115 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67117 = SURFACE_STYLE_USAGE ( .BOTH. , #36014 ) ; +#67116 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#67118 = SURFACE_SIDE_STYLE ('',( #82960 ) ) ; +#67119 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67121 = ADVANCED_FACE ( 'NONE', ( #32451 ), #85035, .T. ) ; +#67120 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#67122 = LINE ( 'NONE', #66622, #25496 ) ; +#67123 = ORIENTED_EDGE ( 'NONE', *, *, #83341, .T. ) ; +#67124 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#67125 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#67126 = LINE ( 'NONE', #98205, #97128 ) ; +#67127 = ORIENTED_EDGE ( 'NONE', *, *, #60063, .F. ) ; +#67128 = ORIENTED_EDGE ( 'NONE', *, *, #61803, .T. ) ; +#67129 = AXIS2_PLACEMENT_3D ( 'NONE', #51706, #27728, #97116 ) ; +#67130 = EDGE_CURVE ( 'NONE', #49779, #95534, #57606, .T. ) ; +#67131 = EDGE_CURVE ( 'NONE', #86914, #28348, #61592, .T. ) ; +#67133 = FILL_AREA_STYLE_COLOUR ( '', #90555 ) ; +#67132 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67134 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67135 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#67136 = AXIS2_PLACEMENT_3D ( 'NONE', #58368, #2704, #57345 ) ; +#67137 = ADVANCED_FACE ( 'NONE', ( #94188 ), #24819, .T. ) ; +#67138 = LINE ( 'NONE', #21182, #27217 ) ; +#67139 = ADVANCED_FACE ( 'NONE', ( #63612 ), #55947, .T. ) ; +#67140 = VERTEX_POINT ( 'NONE', #9376 ) ; +#67141 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#67142 = VERTEX_POINT ( 'NONE', #57977 ) ; +#67143 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#67145 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67144 = FILL_AREA_STYLE ('',( #36039 ) ) ; +#67146 = FILL_AREA_STYLE ('',( #83491 ) ) ; +#67147 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67148 = ADVANCED_FACE ( 'NONE', ( #34480 ), #49799, .T. ) ; +#67149 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2439 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27900, #97285, #89660 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67150 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96434 ), #89970 ) ; +#67151 = FILL_AREA_STYLE ('',( #12959 ) ) ; +#67152 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#67153 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#67154 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67155 = VECTOR ( 'NONE', #22197, 1000.000000000000000 ) ; +#67156 = ADVANCED_FACE ( 'NONE', ( #64095 ), #41621, .T. ) ; +#67157 = FACE_OUTER_BOUND ( 'NONE', #16981, .T. ) ; +#67158 = ORIENTED_EDGE ( 'NONE', *, *, #42330, .F. ) ; +#67159 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67162 = FACE_OUTER_BOUND ( 'NONE', #24609, .T. ) ; +#67161 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, -3.149999999999990585, 0.000000000000000000 ) ) ; +#67160 = LINE ( 'NONE', #28861, #5506 ) ; +#67163 = VECTOR ( 'NONE', #41148, 1000.000000000000000 ) ; +#67164 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54414, 'distance_accuracy_value', 'NONE'); +#67165 = DIRECTION ( 'NONE', ( 0.000000000000000000, 6.123233995736766036E-17, 1.000000000000000000 ) ) ; +#67166 = SURFACE_STYLE_USAGE ( .BOTH. , #67646 ) ; +#67167 = AXIS2_PLACEMENT_3D ( 'NONE', #51462, #44247, #28944 ) ; +#67168 = FACE_OUTER_BOUND ( 'NONE', #87476, .T. ) ; +#67169 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67170 = FILL_AREA_STYLE_COLOUR ( '', #27225 ) ; +#67171 = ORIENTED_EDGE ( 'NONE', *, *, #45201, .T. ) ; +#67172 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67173 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#67174 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67175 = CYLINDRICAL_SURFACE ( 'NONE', #31773, 0.04999999999999991257 ) ; +#67176 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2750000000000000222, 0.1458578643762690474 ) ) ; +#67177 = FILL_AREA_STYLE_COLOUR ( '', #10904 ) ; +#67178 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67179 = LINE ( 'NONE', #69675, #3357 ) ; +#67180 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#67181 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67182 = FILL_AREA_STYLE_COLOUR ( '', #217 ) ; +#67183 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146550232, 0.5686465759269649922, 0.8299999999999999600 ) ) ; +#67184 = FACE_OUTER_BOUND ( 'NONE', #90414, .T. ) ; +#67185 = LINE ( 'NONE', #83027, #34133 ) ; +#67186 = PRESENTATION_STYLE_ASSIGNMENT (( #37581 ) ) ; +#67187 = LINE ( 'NONE', #11981, #42151 ) ; +#67188 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#67189 = ADVANCED_FACE ( 'NONE', ( #33467 ), #50322, .F. ) ; +#67190 = FACE_OUTER_BOUND ( 'NONE', #82822, .T. ) ; +#67191 = SURFACE_STYLE_FILL_AREA ( #29404 ) ; +#67192 = SURFACE_STYLE_USAGE ( .BOTH. , #2539 ) ; +#67193 = LINE ( 'NONE', #90690, #86214 ) ; +#67194 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.399999999999999911, -11.41999999999999993 ) ) ; +#67195 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83464 ), #70393 ) ; +#67196 = EDGE_CURVE ( 'NONE', #78820, #94767, #5268, .T. ) ; +#67197 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#67198 = ORIENTED_EDGE ( 'NONE', *, *, #36996, .F. ) ; +#67199 = CARTESIAN_POINT ( 'NONE', ( 9.125548750250088048, 9.827966249749911398, 0.8648700000000000276 ) ) ; +#67200 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.000000000000000000 ) ) ; +#67201 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67202 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51156 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47610, #77739, #47096 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67204 = SURFACE_STYLE_FILL_AREA ( #35600 ) ; +#67203 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67205 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67206 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57766, #42414, #49076 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67207 = FACE_OUTER_BOUND ( 'NONE', #34672, .T. ) ; +#67208 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#67209 = VERTEX_POINT ( 'NONE', #67578 ) ; +#67210 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#67211 = SURFACE_STYLE_USAGE ( .BOTH. , #36603 ) ; +#67212 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70484 ), #23206 ) ; +#67213 = VERTEX_POINT ( 'NONE', #68582 ) ; +#67214 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#67215 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67216 = STYLED_ITEM ( 'NONE', ( #56929 ), #35371 ) ; +#67217 = EDGE_CURVE ( 'NONE', #11208, #29928, #27828, .T. ) ; +#67218 = ORIENTED_EDGE ( 'NONE', *, *, #91517, .T. ) ; +#67219 = ORIENTED_EDGE ( 'NONE', *, *, #68245, .T. ) ; +#67220 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74893 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71700, #39543, #63051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67221 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67222 = VERTEX_POINT ( 'NONE', #28307 ) ; +#67223 = CARTESIAN_POINT ( 'NONE', ( 1.823253843827010057, -1.327673353236110021, 0.8100000000000000533 ) ) ; +#67224 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.149999999999999911, 0.000000000000000000 ) ) ; +#67225 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#67226 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83458 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21299, #37148, #92716 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67227 = VECTOR ( 'NONE', #9200, 1000.000000000000000 ) ; +#67228 = STYLED_ITEM ( 'NONE', ( #72607 ), #36502 ) ; +#67229 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99483 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34971, #74255, #26804 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67230 = FACE_OUTER_BOUND ( 'NONE', #86821, .T. ) ; +#67232 = ORIENTED_EDGE ( 'NONE', *, *, #43865, .F. ) ; +#67231 = VERTEX_POINT ( 'NONE', #43599 ) ; +#67233 = VECTOR ( 'NONE', #76275, 1000.000000000000000 ) ; +#67234 = EDGE_LOOP ( 'NONE', ( #1471, #64543, #32586, #21666 ) ) ; +#67235 = STYLED_ITEM ( 'NONE', ( #58181 ), #8786 ) ; +#67236 = ORIENTED_EDGE ( 'NONE', *, *, #33314, .T. ) ; +#67237 = DIRECTION ( 'NONE', ( 0.7071060119555152568, -0.7071075504167430026, 0.000000000000000000 ) ) ; +#67238 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15540, 'distance_accuracy_value', 'NONE'); +#67239 = VECTOR ( 'NONE', #32861, 1000.000000000000000 ) ; +#67241 = DIRECTION ( 'NONE', ( 0.7071067811865462405, -0.7071067811865489050, 0.000000000000000000 ) ) ; +#67240 = SURFACE_STYLE_FILL_AREA ( #58626 ) ; +#67242 = EDGE_CURVE ( 'NONE', #36018, #21034, #91082, .T. ) ; +#67243 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7445 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3999, #66292, #82134 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67244 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67245 = SURFACE_STYLE_FILL_AREA ( #58632 ) ; +#67246 = CARTESIAN_POINT ( 'NONE', ( -1.216120372379269954, -0.8900438058027670962, 0.8299999999999999600 ) ) ; +#67247 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67248 = EDGE_LOOP ( 'NONE', ( #77805, #73542, #40984, #24070, #97314, #92896 ) ) ; +#67249 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#67250 = ORIENTED_EDGE ( 'NONE', *, *, #87077, .F. ) ; +#67251 = EDGE_LOOP ( 'NONE', ( #31562, #66391, #65362, #96382 ) ) ; +#67252 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26540 ) ) ; +#67253 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67254 = DIRECTION ( 'NONE', ( 8.881784197001252323E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67255 = SURFACE_SIDE_STYLE ('',( #44756 ) ) ; +#67256 = CIRCLE ( 'NONE', #18338, 0.1000000000000000056 ) ; +#67258 = ORIENTED_EDGE ( 'NONE', *, *, #9197, .F. ) ; +#67257 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67259 = EDGE_CURVE ( 'NONE', #38287, #13965, #62539, .T. ) ; +#67260 = PRESENTATION_STYLE_ASSIGNMENT (( #21803 ) ) ; +#67261 = SURFACE_STYLE_FILL_AREA ( #36154 ) ; +#67262 = ORIENTED_EDGE ( 'NONE', *, *, #63007, .T. ) ; +#67264 = FACE_OUTER_BOUND ( 'NONE', #65739, .T. ) ; +#67263 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#67265 = SURFACE_SIDE_STYLE ('',( #51978 ) ) ; +#67267 = VERTEX_POINT ( 'NONE', #98652 ) ; +#67266 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67268 = ORIENTED_EDGE ( 'NONE', *, *, #42330, .T. ) ; +#67270 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, 0.9464466094067259805 ) ) ; +#67269 = CARTESIAN_POINT ( 'NONE', ( 0.5312032056918729594, -0.9984395139652609830, 0.8299999999999992939 ) ) ; +#67271 = PRESENTATION_STYLE_ASSIGNMENT (( #15110 ) ) ; +#67272 = AXIS2_PLACEMENT_3D ( 'NONE', #98390, #14157, #36203 ) ; +#67273 = FILL_AREA_STYLE_COLOUR ( '', #7398 ) ; +#67274 = PLANE ( 'NONE', #18540 ) ; +#67275 = FACE_OUTER_BOUND ( 'NONE', #6136, .T. ) ; +#67276 = EDGE_CURVE ( 'NONE', #15082, #28951, #74769, .T. ) ; +#67277 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8958, 'distance_accuracy_value', 'NONE'); +#67278 = ORIENTED_EDGE ( 'NONE', *, *, #10653, .T. ) ; +#67279 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#67280 = VERTEX_POINT ( 'NONE', #37479 ) ; +#67281 = CARTESIAN_POINT ( 'NONE', ( 1.441396927522579974, -1.330101555947649894, 0.8299999999999999600 ) ) ; +#67282 = FILL_AREA_STYLE ('',( #36679 ) ) ; +#67283 = CIRCLE ( 'NONE', #6852, 0.1000000000000000194 ) ; +#67284 = LINE ( 'NONE', #75959, #53307 ) ; +#67285 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67286 = SURFACE_STYLE_USAGE ( .BOTH. , #28499 ) ; +#67287 = ORIENTED_EDGE ( 'NONE', *, *, #36874, .T. ) ; +#67288 = SURFACE_SIDE_STYLE ('',( #81654 ) ) ; +#67289 = FACE_OUTER_BOUND ( 'NONE', #75573, .T. ) ; +#67290 = CARTESIAN_POINT ( 'NONE', ( 11.21151312487495666, 5.705533124874956563, 0.8991599999999999593 ) ) ; +#67291 = LINE ( 'NONE', #232, #85187 ) ; +#67292 = SURFACE_SIDE_STYLE ('',( #4994 ) ) ; +#67293 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.266666666666653285, 0.000000000000000000 ) ) ; +#67294 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#67296 = CARTESIAN_POINT ( 'NONE', ( 1.901168164643999958, -1.316888414733939916, 0.8299999999999999600 ) ) ; +#67295 = STYLED_ITEM ( 'NONE', ( #64896 ), #60469 ) ; +#67297 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38018 ) ) ; +#67298 = PLANE ( 'NONE', #8938 ) ; +#67299 = AXIS2_PLACEMENT_3D ( 'NONE', #1040, #31676, #23026 ) ; +#67300 = EDGE_CURVE ( 'NONE', #24220, #86833, #23500, .T. ) ; +#67301 = FILL_AREA_STYLE ('',( #74984 ) ) ; +#67302 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67303 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#67304 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#67305 = VECTOR ( 'NONE', #85838, 1000.000000000000000 ) ; +#67306 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01085786437626909580, 0.2434314575050762763 ) ) ; +#67307 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67308 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8547 ) ) ; +#67309 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67310 = EDGE_LOOP ( 'NONE', ( #53806, #70112, #35617, #49983 ) ) ; +#67312 = EDGE_CURVE ( 'NONE', #94818, #54937, #66591, .T. ) ; +#67311 = LINE ( 'NONE', #37212, #61725 ) ; +#67313 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#67314 = ORIENTED_EDGE ( 'NONE', *, *, #25606, .F. ) ; +#67315 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67316 = FACE_OUTER_BOUND ( 'NONE', #23694, .T. ) ; +#67317 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8299999999999999600 ) ) ; +#67318 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67319 = VECTOR ( 'NONE', #92665, 1000.000000000000114 ) ; +#67320 = DIRECTION ( 'NONE', ( 0.7071067811865469066, 0.7071067811865482389, 0.000000000000000000 ) ) ; +#67321 = CARTESIAN_POINT ( 'NONE', ( 1.386618070225959176, -0.9667022860554699282, 0.8100000000000108225 ) ) ; +#67322 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#67323 = SURFACE_STYLE_FILL_AREA ( #44825 ) ; +#67324 = ORIENTED_EDGE ( 'NONE', *, *, #7809, .F. ) ; +#67325 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46083 ) ) ; +#67326 = LINE ( 'NONE', #43348, #84198 ) ; +#67327 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.300000000000000266, 0.000000000000000000 ) ) ; +#67328 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#67329 = FILL_AREA_STYLE_COLOUR ( '', #100779 ) ; +#67330 = SURFACE_STYLE_USAGE ( .BOTH. , #6495 ) ; +#67331 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#67332 = STYLED_ITEM ( 'NONE', ( #37234 ), #53043 ) ; +#67333 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8648700000000000276 ) ) ; +#67334 = EDGE_CURVE ( 'NONE', #23866, #46873, #68074, .T. ) ; +#67335 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01085786437626904202, 0.1434314575050762153 ) ) ; +#67336 = ORIENTED_EDGE ( 'NONE', *, *, #79900, .F. ) ; +#67337 = VERTEX_POINT ( 'NONE', #44115 ) ; +#67338 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57550 ), #80421 ) ; +#67339 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67340 = ORIENTED_EDGE ( 'NONE', *, *, #6565, .T. ) ; +#67341 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#67343 = ADVANCED_FACE ( 'NONE', ( #98166 ), #75271, .F. ) ; +#67342 = AXIS2_PLACEMENT_3D ( 'NONE', #79468, #87612, #64633 ) ; +#67344 = VECTOR ( 'NONE', #44229, 1000.000000000000000 ) ; +#67345 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#67346 = SURFACE_STYLE_USAGE ( .BOTH. , #20894 ) ; +#67347 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67348 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#67349 = CARTESIAN_POINT ( 'NONE', ( -0.3919372300192849878, -0.9729160362892149694, 0.8299999999999999600 ) ) ; +#67350 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67351 = PLANE ( 'NONE', #18673 ) ; +#67353 = ORIENTED_EDGE ( 'NONE', *, *, #45910, .T. ) ; +#67352 = ORIENTED_EDGE ( 'NONE', *, *, #5579, .T. ) ; +#67354 = ORIENTED_EDGE ( 'NONE', *, *, #5693, .T. ) ; +#67355 = CARTESIAN_POINT ( 'NONE', ( 1.635208922267139986, -0.9074576374047379490, 0.8099999999999981659 ) ) ; +#67357 = AXIS2_PLACEMENT_3D ( 'NONE', #71710, #9336, #42080 ) ; +#67356 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66683, 'distance_accuracy_value', 'NONE'); +#67358 = AXIS2_PLACEMENT_3D ( 'NONE', #79773, #64438, #86404 ) ; +#67359 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49296, 'distance_accuracy_value', 'NONE'); +#67360 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#67361 = ORIENTED_EDGE ( 'NONE', *, *, #46744, .F. ) ; +#67362 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30677, #45475, #30182, #70504 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67363 = STYLED_ITEM ( 'NONE', ( #70605 ), #21258 ) ; +#67365 = ADVANCED_FACE ( 'NONE', ( #46609 ), #78289, .T. ) ; +#67364 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2411, #95795, #88181, #18186 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67366 = ORIENTED_EDGE ( 'NONE', *, *, #21775, .F. ) ; +#67367 = EDGE_CURVE ( 'NONE', #18757, #8714, #86442, .T. ) ; +#67368 = SURFACE_STYLE_USAGE ( .BOTH. , #76035 ) ; +#67369 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67370 = AXIS2_PLACEMENT_3D ( 'NONE', #51810, #75288, #22663 ) ; +#67371 = AXIS2_PLACEMENT_3D ( 'NONE', #86725, #41783, #93826 ) ; +#67372 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01085786437626898131, -0.1500000000000000222 ) ) ; +#67373 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67374 = EDGE_LOOP ( 'NONE', ( #7894, #24556, #22175, #79829 ) ) ; +#67375 = VERTEX_POINT ( 'NONE', #62986 ) ; +#67376 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67114 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23460, #68383, #93848 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67377 = ORIENTED_EDGE ( 'NONE', *, *, #90525, .T. ) ; +#67378 = SURFACE_STYLE_USAGE ( .BOTH. , #86082 ) ; +#67379 = VECTOR ( 'NONE', #37228, 1000.000000000000000 ) ; +#67380 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67381 = FILL_AREA_STYLE ('',( #98444 ) ) ; +#67383 = ORIENTED_EDGE ( 'NONE', *, *, #92153, .T. ) ; +#67382 = FACE_OUTER_BOUND ( 'NONE', #20355, .T. ) ; +#67384 = EDGE_CURVE ( 'NONE', #6703, #77948, #88605, .T. ) ; +#67385 = FACE_OUTER_BOUND ( 'NONE', #82021, .T. ) ; +#67386 = FILL_AREA_STYLE ('',( #20415 ) ) ; +#67387 = ORIENTED_EDGE ( 'NONE', *, *, #16178, .F. ) ; +#67388 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67389 = ORIENTED_EDGE ( 'NONE', *, *, #36226, .T. ) ; +#67390 = VERTEX_POINT ( 'NONE', #24181 ) ; +#67391 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#67392 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#67393 = SURFACE_STYLE_USAGE ( .BOTH. , #44392 ) ; +#67394 = FILL_AREA_STYLE ('',( #59293 ) ) ; +#67395 = FILL_AREA_STYLE_COLOUR ( '', #17775 ) ; +#67396 = EDGE_CURVE ( 'NONE', #90763, #27347, #53293, .T. ) ; +#67397 = FILL_AREA_STYLE ('',( #44401 ) ) ; +#67398 = ORIENTED_EDGE ( 'NONE', *, *, #69462, .T. ) ; +#67399 = SURFACE_STYLE_USAGE ( .BOTH. , #36780 ) ; +#67400 = CARTESIAN_POINT ( 'NONE', ( -0.9721805927153830407, -1.463531211619029992, 0.8299999999999999600 ) ) ; +#67401 = VERTEX_POINT ( 'NONE', #8736 ) ; +#67402 = VECTOR ( 'NONE', #29952, 1000.000000000000000 ) ; +#67403 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67404 = CARTESIAN_POINT ( 'NONE', ( -0.2448925227682630101, -1.469666695271939938, 0.8299999999999999600 ) ) ; +#67405 = LINE ( 'NONE', #22980, #87122 ) ; +#67406 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67407 = AXIS2_PLACEMENT_3D ( 'NONE', #79939, #18096, #26318 ) ; +#67409 = PRESENTATION_STYLE_ASSIGNMENT (( #23871 ) ) ; +#67408 = FILL_AREA_STYLE_COLOUR ( '', #33189 ) ; +#67410 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67411 = PRESENTATION_STYLE_ASSIGNMENT (( #60794 ) ) ; +#67412 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999709359 ) ) ; +#67413 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67414 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#67415 = STYLED_ITEM ( 'NONE', ( #31544 ), #47481 ) ; +#67416 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78099 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100493, #47002, #11137 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67417 = LINE ( 'NONE', #21461, #9093 ) ; +#67418 = EDGE_CURVE ( 'NONE', #71777, #82970, #15454, .T. ) ; +#67419 = SURFACE_SIDE_STYLE ('',( #91416 ) ) ; +#67422 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#67421 = SURFACE_SIDE_STYLE ('',( #27151 ) ) ; +#67420 = AXIS2_PLACEMENT_3D ( 'NONE', #98581, #52245, #75694 ) ; +#67423 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67424 = CIRCLE ( 'NONE', #23420, 0.04999999999999991257 ) ; +#67425 = VERTEX_POINT ( 'NONE', #14429 ) ; +#67426 = CARTESIAN_POINT ( 'NONE', ( -0.9900422999955440506, -1.351484773706350007, 0.8299999999999999600 ) ) ; +#67427 = ADVANCED_FACE ( 'NONE', ( #53785 ), #45566, .T. ) ; +#67428 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67429 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584400679, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#67430 = AXIS2_PLACEMENT_3D ( 'NONE', #25221, #61988, #23170 ) ; +#67431 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#67432 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23428 ), #54425 ) ; +#67433 = SURFACE_SIDE_STYLE ('',( #13240 ) ) ; +#67434 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, 3.500000000000000444, 0.000000000000000000 ) ) ; +#67435 = LINE ( 'NONE', #82775, #74995 ) ; +#67437 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67436 = VECTOR ( 'NONE', #47316, 1000.000000000000000 ) ; +#67438 = LINE ( 'NONE', #18968, #68126 ) ; +#67439 = ORIENTED_EDGE ( 'NONE', *, *, #79793, .T. ) ; +#67440 = PRESENTATION_STYLE_ASSIGNMENT (( #50661 ) ) ; +#67441 = ORIENTED_EDGE ( 'NONE', *, *, #5321, .F. ) ; +#67442 = SURFACE_STYLE_FILL_AREA ( #12758 ) ; +#67443 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43083, 'distance_accuracy_value', 'NONE'); +#67444 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88943, 'distance_accuracy_value', 'NONE'); +#67445 = SURFACE_STYLE_FILL_AREA ( #90946 ) ; +#67446 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#67447 = FILL_AREA_STYLE_COLOUR ( '', #16765 ) ; +#67448 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67449 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67450 = ORIENTED_EDGE ( 'NONE', *, *, #18337, .T. ) ; +#67451 = PRESENTATION_STYLE_ASSIGNMENT (( #60350 ) ) ; +#67452 = ORIENTED_EDGE ( 'NONE', *, *, #32888, .F. ) ; +#67453 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8648700000000000276 ) ) ; +#67454 = EDGE_LOOP ( 'NONE', ( #84704, #16470, #26533, #91238 ) ) ; +#67455 = STYLED_ITEM ( 'NONE', ( #70678 ), #71907 ) ; +#67456 = EDGE_CURVE ( 'NONE', #55106, #33509, #41765, .T. ) ; +#67457 = ADVANCED_FACE ( 'NONE', ( #41011 ), #25676, .F. ) ; +#67458 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67459 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67460 = SURFACE_STYLE_USAGE ( .BOTH. , #76634 ) ; +#67461 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67463 = ORIENTED_EDGE ( 'NONE', *, *, #60144, .T. ) ; +#67462 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64216 ) ) ; +#67464 = SURFACE_SIDE_STYLE ('',( #59870 ) ) ; +#67465 = VERTEX_POINT ( 'NONE', #56841 ) ; +#67467 = CARTESIAN_POINT ( 'NONE', ( -0.5440898474478359503, -0.9715902597976999733, 0.8099999999999990541 ) ) ; +#67466 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67468 = EDGE_LOOP ( 'NONE', ( #99197, #32883, #83630, #49507, #77511, #79598 ) ) ; +#67469 = EDGE_CURVE ( 'NONE', #54178, #97613, #64910, .T. ) ; +#67470 = ORIENTED_EDGE ( 'NONE', *, *, #53971, .T. ) ; +#67471 = EDGE_CURVE ( 'NONE', #99336, #30553, #63490, .T. ) ; +#67472 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67473 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#67474 = SURFACE_STYLE_USAGE ( .BOTH. , #83832 ) ; +#67475 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67476 = EDGE_LOOP ( 'NONE', ( #73593, #12115, #71682, #53439 ) ) ; +#67477 = ADVANCED_FACE ( 'NONE', ( #26186 ), #42006, .T. ) ; +#67478 = ORIENTED_EDGE ( 'NONE', *, *, #23314, .T. ) ; +#67479 = ORIENTED_EDGE ( 'NONE', *, *, #86315, .T. ) ; +#67480 = CARTESIAN_POINT ( 'NONE', ( 0.6702516233766230291, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#67482 = ORIENTED_EDGE ( 'NONE', *, *, #46223, .F. ) ; +#67481 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#67483 = EDGE_CURVE ( 'NONE', #37124, #14217, #21509, .T. ) ; +#67484 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67485 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#67486 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#67487 = EDGE_LOOP ( 'NONE', ( #92444, #65333, #11788, #4651 ) ) ; +#67488 = LINE ( 'NONE', #30551, #76559 ) ; +#67490 = LINE ( 'NONE', #29706, #40283 ) ; +#67489 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31871 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44193, #21720, #69677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67491 = FILL_AREA_STYLE ('',( #44028 ) ) ; +#67492 = VERTEX_POINT ( 'NONE', #21020 ) ; +#67493 = EDGE_CURVE ( 'NONE', #72086, #6118, #66470, .T. ) ; +#67494 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#67496 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87521 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71192, #53866, #23740 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #132 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39119, #5912, #99308 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67497 = FILL_AREA_STYLE_COLOUR ( '', #71731 ) ; +#67498 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#67499 = CARTESIAN_POINT ( 'NONE', ( 1.719030235149860086, -1.443664018207750033, 0.8100000000000000533 ) ) ; +#67500 = EDGE_CURVE ( 'NONE', #47020, #60913, #52832, .T. ) ; +#67501 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67503 = EDGE_CURVE ( 'NONE', #65881, #63509, #36851, .T. ) ; +#67502 = FACE_OUTER_BOUND ( 'NONE', #36609, .T. ) ; +#67504 = EDGE_LOOP ( 'NONE', ( #78466, #87624, #11656, #87552 ) ) ; +#67505 = AXIS2_PLACEMENT_3D ( 'NONE', #76032, #84694, #61246 ) ; +#67506 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8991599999999999593 ) ) ; +#67507 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2400000000000000466 ) ) ; +#67508 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#67510 = CARTESIAN_POINT ( 'NONE', ( 1.575220826706200006, -1.366783821657739928, 0.8100000000000000533 ) ) ; +#67509 = CARTESIAN_POINT ( 'NONE', ( 0.4481429611221979803, -1.007711706028959986, 0.8299999999999999600 ) ) ; +#67511 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999430, 7.437945000000000917, 0.8648700000000000276 ) ) ; +#67512 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67513 = PRODUCT_DEFINITION ( 'δ֪', '', #60067, #82047 ) ; +#67514 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69091 ) ) ; +#67515 = LINE ( 'NONE', #60421, #86858 ) ; +#67516 = ORIENTED_EDGE ( 'NONE', *, *, #5178, .F. ) ; +#67517 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67518 = PRESENTATION_STYLE_ASSIGNMENT (( #62294 ) ) ; +#67519 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#67520 = SURFACE_STYLE_USAGE ( .BOTH. , #62297 ) ; +#67521 = VERTEX_POINT ( 'NONE', #4678 ) ; +#67522 = ADVANCED_FACE ( 'NONE', ( #83813 ), #50687, .T. ) ; +#67523 = PLANE ( 'NONE', #97640 ) ; +#67524 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17792, #95898, #64778 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67525 = SURFACE_SIDE_STYLE ('',( #83388 ) ) ; +#67526 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67527 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#67528 = SURFACE_STYLE_FILL_AREA ( #82882 ) ; +#67529 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67530 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#67531 = ORIENTED_EDGE ( 'NONE', *, *, #43964, .F. ) ; +#67532 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#67533 = EDGE_CURVE ( 'NONE', #38992, #35120, #83318, .T. ) ; +#67534 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8648700000000000276 ) ) ; +#67535 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67536 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766240006, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#67537 = STYLED_ITEM ( 'NONE', ( #9080 ), #87504 ) ; +#67538 = SURFACE_SIDE_STYLE ('',( #52767 ) ) ; +#67539 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67540 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67541 = SURFACE_STYLE_USAGE ( .BOTH. , #37450 ) ; +#67542 = ADVANCED_FACE ( 'NONE', ( #89466 ), #74147, .T. ) ; +#67543 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67544 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#67545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65441, #36828, #89932 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67546 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8099999999998959144 ) ) ; +#67547 = SURFACE_STYLE_USAGE ( .BOTH. , #74740 ) ; +#67548 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14626, 'distance_accuracy_value', 'NONE'); +#67549 = EDGE_LOOP ( 'NONE', ( #35243, #21016, #10123, #58550 ) ) ; +#67550 = FACE_OUTER_BOUND ( 'NONE', #1696, .T. ) ; +#67551 = EDGE_LOOP ( 'NONE', ( #46052, #68096, #6747, #66465 ) ) ; +#67552 = FILL_AREA_STYLE ('',( #12875 ) ) ; +#67553 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39031, 'distance_accuracy_value', 'NONE'); +#67554 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97935, 'distance_accuracy_value', 'NONE'); +#67555 = LINE ( 'NONE', #20097, #99200 ) ; +#67556 = DIRECTION ( 'NONE', ( 2.058195874565369951E-47, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67557 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#67558 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89771, #72431, #87769 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67559 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67560 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#67561 = CARTESIAN_POINT ( 'NONE', ( -1.529289321881347696, 1.970710678118652082, -0.02000000000000000042 ) ) ; +#67562 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#67563 = VECTOR ( 'NONE', #14275, 1000.000000000000000 ) ; +#67564 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#67565 = EDGE_LOOP ( 'NONE', ( #23388, #56608, #37110, #74030, #97860, #53814 ) ) ; +#67566 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67567 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#67568 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31988, 'distance_accuracy_value', 'NONE'); +#67570 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25286 ), #8827 ) ; +#67569 = STYLED_ITEM ( 'NONE', ( #38000 ), #38430 ) ; +#67571 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42449, #80754, #34302, #73579 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67572 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67573 = EDGE_LOOP ( 'NONE', ( #65488, #82597, #84696, #74318 ) ) ; +#67574 = PLANE ( 'NONE', #51079 ) ; +#67575 = EDGE_CURVE ( 'NONE', #78436, #32075, #84306, .T. ) ; +#67576 = SURFACE_STYLE_USAGE ( .BOTH. , #82930 ) ; +#67577 = VECTOR ( 'NONE', #2910, 999.9999999999998863 ) ; +#67578 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8648700000000000276 ) ) ; +#67579 = LINE ( 'NONE', #44588, #6448 ) ; +#67580 = CARTESIAN_POINT ( 'NONE', ( 0.2900000000000000355, -0.01085786437626902814, -0.1500000000000000222 ) ) ; +#67581 = VERTEX_POINT ( 'NONE', #54696 ) ; +#67582 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61791 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78536, #64240, #1961 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67583 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65407, 'distance_accuracy_value', 'NONE'); +#67584 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#67585 = SURFACE_STYLE_FILL_AREA ( #91093 ) ; +#67586 = ORIENTED_EDGE ( 'NONE', *, *, #50026, .F. ) ; +#67587 = FILL_AREA_STYLE_COLOUR ( '', #81521 ) ; +#67588 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8778 ) ) ; +#67589 = LINE ( 'NONE', #98669, #4786 ) ; +#67590 = CARTESIAN_POINT ( 'NONE', ( 1.594774167960719913, -1.488490865982160294, 0.8300000000000001821 ) ) ; +#67591 = EDGE_LOOP ( 'NONE', ( #74841, #32446, #70934, #47288, #18556, #73401 ) ) ; +#67592 = STYLED_ITEM ( 'NONE', ( #1199 ), #72473 ) ; +#67593 = ORIENTED_EDGE ( 'NONE', *, *, #17398, .T. ) ; +#67595 = ORIENTED_EDGE ( 'NONE', *, *, #91221, .T. ) ; +#67594 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#67596 = LINE ( 'NONE', #51823, #96385 ) ; +#67597 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59594 ) ) ; +#67599 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67598 = FACE_OUTER_BOUND ( 'NONE', #45448, .T. ) ; +#67600 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5633 ), #84033 ) ; +#67601 = ORIENTED_EDGE ( 'NONE', *, *, #56170, .F. ) ; +#67602 = SURFACE_STYLE_USAGE ( .BOTH. , #37006 ) ; +#67603 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67604 = SURFACE_STYLE_FILL_AREA ( #36517 ) ; +#67605 = ORIENTED_EDGE ( 'NONE', *, *, #76343, .T. ) ; +#67606 = CARTESIAN_POINT ( 'NONE', ( 1.429960467956949977, -1.401385721107119897, 0.8100000000000000533 ) ) ; +#67607 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99392 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37382, #44491, #28209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67608 = STYLED_ITEM ( 'NONE', ( #19196 ), #88698 ) ; +#67609 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#67610 = CARTESIAN_POINT ( 'NONE', ( -0.1150130133853430048, 0.2193340759269659934, 0.8299999999999999600 ) ) ; +#67611 = ORIENTED_EDGE ( 'NONE', *, *, #43204, .T. ) ; +#67613 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67612 = CARTESIAN_POINT ( 'NONE', ( 1.797929489527179792, -1.085974092738729802, 0.8099999999999998312 ) ) ; +#67614 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67615 = ORIENTED_EDGE ( 'NONE', *, *, #19359, .F. ) ; +#67616 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94655 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14348, #28710, #68507 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67618 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#67617 = SURFACE_SIDE_STYLE ('',( #12437 ) ) ; +#67619 = FILL_AREA_STYLE_COLOUR ( '', #13009 ) ; +#67620 = EDGE_CURVE ( 'NONE', #93243, #55589, #31688, .T. ) ; +#67621 = SURFACE_STYLE_FILL_AREA ( #97259 ) ; +#67622 = AXIS2_PLACEMENT_3D ( 'NONE', #13596, #44785, #21835 ) ; +#67623 = SURFACE_SIDE_STYLE ('',( #31738 ) ) ; +#67624 = AXIS2_PLACEMENT_3D ( 'NONE', #31274, #77228, #61947 ) ; +#67625 = ORIENTED_EDGE ( 'NONE', *, *, #77643, .F. ) ; +#67626 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#67627 = ORIENTED_EDGE ( 'NONE', *, *, #10382, .F. ) ; +#67629 = SURFACE_SIDE_STYLE ('',( #61532 ) ) ; +#67628 = LINE ( 'NONE', #58039, #31430 ) ; +#67630 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#67631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30177 ), #12189 ) ; +#67632 = VECTOR ( 'NONE', #96676, 1000.000000000000000 ) ; +#67633 = FILL_AREA_STYLE_COLOUR ( '', #37799 ) ; +#67634 = PLANE ( 'NONE', #14792 ) ; +#67635 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, 0.000000000000000000, -0.1499999999999999667 ) ) ; +#67636 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67637 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.5000000000000000000, -0.02000000000001675091 ) ) ; +#67638 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45418 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88528, #80380, #42067 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67639 = FILL_AREA_STYLE ('',( #77317 ) ) ; +#67640 = LINE ( 'NONE', #20697, #74827 ) ; +#67641 = VERTEX_POINT ( 'NONE', #37364 ) ; +#67642 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#67644 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67643 = PRESENTATION_STYLE_ASSIGNMENT (( #5344 ) ) ; +#67645 = LINE ( 'NONE', #84004, #27324 ) ; +#67646 = SURFACE_SIDE_STYLE ('',( #10429 ) ) ; +#67647 = STYLED_ITEM ( 'NONE', ( #39468 ), #12637 ) ; +#67648 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#67649 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67650 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67651 = ORIENTED_EDGE ( 'NONE', *, *, #23855, .T. ) ; +#67652 = EDGE_CURVE ( 'NONE', #53458, #44242, #30157, .T. ) ; +#67653 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67654 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#67655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67656 = FILL_AREA_STYLE_COLOUR ( '', #44603 ) ; +#67657 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67658 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#67659 = PRESENTATION_STYLE_ASSIGNMENT (( #20209 ) ) ; +#67660 = VECTOR ( 'NONE', #5686, 1000.000000000000000 ) ; +#67661 = SURFACE_STYLE_USAGE ( .BOTH. , #60072 ) ; +#67662 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67663 = LINE ( 'NONE', #8834, #54491 ) ; +#67664 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67665 = CARTESIAN_POINT ( 'NONE', ( -0.5799999999751889179, 0.2999999999999999334, -1.665334536835250932E-17 ) ) ; +#67666 = FACE_OUTER_BOUND ( 'NONE', #65994, .T. ) ; +#67667 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67668 = FILL_AREA_STYLE_COLOUR ( '', #60226 ) ; +#67669 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67670 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85619 ), #16938 ) ; +#67671 = CARTESIAN_POINT ( 'NONE', ( 9.020149180195751297E-35, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#67672 = LINE ( 'NONE', #68675, #41509 ) ; +#67673 = EDGE_CURVE ( 'NONE', #14220, #20515, #93581, .T. ) ; +#67674 = LINE ( 'NONE', #77351, #32687 ) ; +#67675 = FILL_AREA_STYLE_COLOUR ( '', #53668 ) ; +#67676 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86943, 'distance_accuracy_value', 'NONE'); +#67677 = CARTESIAN_POINT ( 'NONE', ( -2.799999999999999822, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#67678 = STYLED_ITEM ( 'NONE', ( #135 ), #89905 ) ; +#67679 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67680 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19263 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36179, #99346, #5951 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67681 = CARTESIAN_POINT ( 'NONE', ( 11.21151300000000184, 5.705533000000000854, 0.8648700000000000276 ) ) ; +#67683 = EDGE_CURVE ( 'NONE', #95346, #10994, #100492, .T. ) ; +#67682 = SURFACE_SIDE_STYLE ('',( #44210 ) ) ; +#67684 = ORIENTED_EDGE ( 'NONE', *, *, #83673, .F. ) ; +#67685 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#67686 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48854, 'distance_accuracy_value', 'NONE'); +#67687 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14125, 'distance_accuracy_value', 'NONE'); +#67688 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67689 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67690 = EDGE_CURVE ( 'NONE', #19543, #50590, #74495, .T. ) ; +#67691 = ADVANCED_FACE ( 'NONE', ( #99523 ), #61359, .T. ) ; +#67692 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#67693 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33569 ) ) ; +#67694 = ORIENTED_EDGE ( 'NONE', *, *, #88716, .T. ) ; +#67695 = SURFACE_SIDE_STYLE ('',( #95310 ) ) ; +#67696 = PLANE ( 'NONE', #52249 ) ; +#67697 = EDGE_LOOP ( 'NONE', ( #8181, #29919, #75540, #8252 ) ) ; +#67698 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#67699 = EDGE_CURVE ( 'NONE', #60027, #56736, #31187, .T. ) ; +#67700 = EDGE_CURVE ( 'NONE', #52699, #19060, #77650, .T. ) ; +#67701 = SURFACE_STYLE_USAGE ( .BOTH. , #51924 ) ; +#67702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81005, 'distance_accuracy_value', 'NONE'); +#67703 = AXIS2_PLACEMENT_3D ( 'NONE', #71611, #49143, #88941 ) ; +#67704 = CARTESIAN_POINT ( 'NONE', ( 0.01532804002844260008, -1.344848644821849959, 0.8300000000000006262 ) ) ; +#67705 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67706 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8972 ) ) ; +#67707 = ORIENTED_EDGE ( 'NONE', *, *, #40514, .T. ) ; +#67708 = ORIENTED_EDGE ( 'NONE', *, *, #41018, .F. ) ; +#67710 = VECTOR ( 'NONE', #83258, 1000.000000000000000 ) ; +#67709 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71018 ) ) ; +#67711 = EDGE_CURVE ( 'NONE', #11007, #43535, #77138, .T. ) ; +#67712 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72620 ) ) ; +#67713 = ORIENTED_EDGE ( 'NONE', *, *, #33314, .F. ) ; +#67714 = PRESENTATION_STYLE_ASSIGNMENT (( #62121 ) ) ; +#67716 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#67715 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #52781, #20609, #13385, #99620 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67717 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#67718 = PLANE ( 'NONE', #8886 ) ; +#67719 = ADVANCED_FACE ( 'NONE', ( #69973 ), #93432, .F. ) ; +#67720 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67721 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #58049, #86625 ) ; +#67722 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67724 = ORIENTED_EDGE ( 'NONE', *, *, #66510, .T. ) ; +#67723 = ORIENTED_EDGE ( 'NONE', *, *, #32004, .F. ) ; +#67725 = EDGE_LOOP ( 'NONE', ( #59430, #8216, #69854, #5799 ) ) ; +#67726 = SURFACE_STYLE_USAGE ( .BOTH. , #28938 ) ; +#67727 = CARTESIAN_POINT ( 'NONE', ( 10.66704149950004776, 8.286473499500051076, 0.8991599999999999593 ) ) ; +#67728 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67729 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67731 = LINE ( 'NONE', #14584, #13752 ) ; +#67730 = CARTESIAN_POINT ( 'NONE', ( 0.4328235538323689791, -0.9111919069839470309, 0.8100000000000000533 ) ) ; +#67732 = SHAPE_REPRESENTATION ( 'Shield Box_ESP32-S3-MINI-1U_20200714', ( #82894 ), #43760 ) ; +#67733 = SURFACE_STYLE_USAGE ( .BOTH. , #89728 ) ; +#67734 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79779 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84324, #45469, #92456 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67735 = CARTESIAN_POINT ( 'NONE', ( -1.343981097684900039, -0.9654894655288509542, 0.8299999999999999600 ) ) ; +#67736 = ORIENTED_EDGE ( 'NONE', *, *, #97086, .F. ) ; +#67737 = STYLED_ITEM ( 'NONE', ( #83238 ), #73016 ) ; +#67738 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67739 = VERTEX_POINT ( 'NONE', #33214 ) ; +#67740 = ORIENTED_EDGE ( 'NONE', *, *, #79667, .F. ) ; +#67741 = CARTESIAN_POINT ( 'NONE', ( 1.041560975556909963, -1.173235213159260049, 0.8100000000000000533 ) ) ; +#67742 = SURFACE_STYLE_FILL_AREA ( #69214 ) ; +#67743 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7071 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #54097, #30569, #70399 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67744 = FACE_OUTER_BOUND ( 'NONE', #20015, .T. ) ; +#67745 = EDGE_CURVE ( 'NONE', #93527, #59388, #32713, .T. ) ; +#67746 = ORIENTED_EDGE ( 'NONE', *, *, #78330, .T. ) ; +#67747 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8099999999998839240 ) ) ; +#67748 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#67749 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#67750 = VECTOR ( 'NONE', #4473, 1000.000000000000000 ) ; +#67751 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88997 ), #937 ) ; +#67752 = VECTOR ( 'NONE', #80764, 1000.000000000000000 ) ; +#67753 = ORIENTED_EDGE ( 'NONE', *, *, #44428, .T. ) ; +#67755 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67754 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67756 = EDGE_LOOP ( 'NONE', ( #99052, #73663, #68340, #94338 ) ) ; +#67757 = EDGE_CURVE ( 'NONE', #66436, #52774, #78645, .T. ) ; +#67758 = ORIENTED_EDGE ( 'NONE', *, *, #37130, .T. ) ; +#67759 = FILL_AREA_STYLE_COLOUR ( '', #19385 ) ; +#67760 = SURFACE_SIDE_STYLE ('',( #91259 ) ) ; +#67761 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#67762 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67763 = FILL_AREA_STYLE ('',( #27499 ) ) ; +#67764 = AXIS2_PLACEMENT_3D ( 'NONE', #21424, #52588, #13698 ) ; +#67765 = PRODUCT ( 'XTAL3225_20210301.xtd', 'XTAL3225_20210301.xtd', '', ( #6508 ) ) ; +#67766 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#67767 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8648700000000000276 ) ) ; +#67768 = EDGE_LOOP ( 'NONE', ( #85025, #79849, #31258, #63179 ) ) ; +#67769 = AXIS2_PLACEMENT_3D ( 'NONE', #64244, #88724, #18759 ) ; +#67770 = LINE ( 'NONE', #51508, #38191 ) ; +#67771 = EDGE_LOOP ( 'NONE', ( #69495, #56387, #74290, #58635 ) ) ; +#67772 = CARTESIAN_POINT ( 'NONE', ( -0.01509916179266439923, -1.018845982455530041, 0.8100000000000000533 ) ) ; +#67773 = CARTESIAN_POINT ( 'NONE', ( 1.063574105442089968, -1.082231071007949907, 0.8299999999999999600 ) ) ; +#67774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75957 ) ) ; +#67775 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, 0.000000000000000000 ) ) ; +#67776 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67777 = CARTESIAN_POINT ( 'NONE', ( -1.723820061220085353, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#67778 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33500 ), #49984 ) ; +#67779 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#67780 = EDGE_LOOP ( 'NONE', ( #60782, #87010, #3587, #48461 ) ) ; +#67781 = ADVANCED_FACE ( 'NONE', ( #95962 ), #63373, .T. ) ; +#67782 = LINE ( 'NONE', #37188, #68812 ) ; +#67783 = SURFACE_STYLE_USAGE ( .BOTH. , #67288 ) ; +#67784 = VECTOR ( 'NONE', #26661, 1000.000000000000000 ) ; +#67785 = CARTESIAN_POINT ( 'NONE', ( 0.1707063580043630124, -1.088378544347549992, 0.8100000000000000533 ) ) ; +#67786 = LINE ( 'NONE', #51530, #40889 ) ; +#67787 = FACE_OUTER_BOUND ( 'NONE', #41054, .T. ) ; +#67788 = FILL_AREA_STYLE_COLOUR ( '', #59815 ) ; +#67789 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9734 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59267, #90353, #45360 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67790 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#67791 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67792 = FACE_OUTER_BOUND ( 'NONE', #59520, .T. ) ; +#67793 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, -0.005000000000000000104, 0.2500000000000000000 ) ) ; +#67794 = SURFACE_SIDE_STYLE ('',( #99848 ) ) ; +#67795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74395, 'distance_accuracy_value', 'NONE'); +#67796 = EDGE_LOOP ( 'NONE', ( #13117, #66235, #5698, #86350 ) ) ; +#67797 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#67798 = CARTESIAN_POINT ( 'NONE', ( -0.9666286830207958536, -0.9667022860554665975, 0.8100000000000125988 ) ) ; +#67799 = ORIENTED_EDGE ( 'NONE', *, *, #26005, .T. ) ; +#67800 = SURFACE_STYLE_USAGE ( .BOTH. , #36703 ) ; +#67801 = FILL_AREA_STYLE ('',( #100352 ) ) ; +#67802 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#67803 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #93005, #115, #39426, #621 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67804 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17383, 'distance_accuracy_value', 'NONE'); +#67805 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#67806 = VECTOR ( 'NONE', #21817, 1000.000000000000000 ) ; +#67807 = CARTESIAN_POINT ( 'NONE', ( 10.38419887512504403, 3.958979875125043346, 0.8991599999999999593 ) ) ; +#67808 = CARTESIAN_POINT ( 'NONE', ( 1.426333131974311108, -1.264135989007903804, 0.8099999999998236389 ) ) ; +#67809 = AXIS2_PLACEMENT_3D ( 'NONE', #34169, #97387, #44773 ) ; +#67810 = ORIENTED_EDGE ( 'NONE', *, *, #73954, .T. ) ; +#67811 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#67812 = EDGE_CURVE ( 'NONE', #85285, #90656, #24580, .T. ) ; +#67813 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44866, 'distance_accuracy_value', 'NONE'); +#67815 = FILL_AREA_STYLE ('',( #28066 ) ) ; +#67814 = AXIS2_PLACEMENT_3D ( 'NONE', #37533, #54356, #38520 ) ; +#67816 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67817 = CARTESIAN_POINT ( 'NONE', ( -0.8360085490496081961, 1.033343808911651340, 0.8299999999999999600 ) ) ; +#67818 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1313, 'distance_accuracy_value', 'NONE'); +#67819 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10014 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33798, #96030, #72569 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67820 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67821 = FILL_AREA_STYLE ('',( #27563 ) ) ; +#67822 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51570 ), #7418 ) ; +#67823 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69326 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85876, #7172, #63439 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67824 = ORIENTED_EDGE ( 'NONE', *, *, #33188, .F. ) ; +#67825 = ORIENTED_EDGE ( 'NONE', *, *, #8359, .F. ) ; +#67826 = EDGE_CURVE ( 'NONE', #57887, #25651, #47717, .T. ) ; +#67827 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58096, 'distance_accuracy_value', 'NONE'); +#67828 = ORIENTED_EDGE ( 'NONE', *, *, #21460, .T. ) ; +#67829 = STYLED_ITEM ( 'NONE', ( #88836 ), #48885 ) ; +#67830 = LINE ( 'NONE', #98910, #90975 ) ; +#67831 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#67832 = EDGE_CURVE ( 'NONE', #34605, #13680, #39782, .T. ) ; +#67833 = LINE ( 'NONE', #13667, #47971 ) ; +#67834 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67835 = CARTESIAN_POINT ( 'NONE', ( -0.4247119971151859796, -0.9357370515645540010, 0.8299999999999999600 ) ) ; +#67836 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24812 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98808, #81603, #27464 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67837 = CARTESIAN_POINT ( 'NONE', ( -1.242030017193550107, -0.9708075278790050389, 0.8299999999999999600 ) ) ; +#67839 = VERTEX_POINT ( 'NONE', #2073 ) ; +#67838 = ORIENTED_EDGE ( 'NONE', *, *, #57813, .F. ) ; +#67840 = AXIS2_PLACEMENT_3D ( 'NONE', #10065, #10562, #48991 ) ; +#67841 = VERTEX_POINT ( 'NONE', #64349 ) ; +#67842 = CARTESIAN_POINT ( 'NONE', ( 1.515867623847370060, -1.051115598670280038, 0.8099999999999981659 ) ) ; +#67844 = LINE ( 'NONE', #30052, #91935 ) ; +#67843 = SURFACE_STYLE_USAGE ( .BOTH. , #5545 ) ; +#67845 = ORIENTED_EDGE ( 'NONE', *, *, #91470, .F. ) ; +#67846 = ORIENTED_EDGE ( 'NONE', *, *, #41528, .T. ) ; +#67848 = STYLED_ITEM ( 'NONE', ( #15779 ), #39514 ) ; +#67847 = FILL_AREA_STYLE ('',( #59261 ) ) ; +#67849 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81165 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97789, #25040, #71476 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67850 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.62344799999999978, 0.8648700000000000276 ) ) ; +#67851 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67852 = FILL_AREA_STYLE_COLOUR ( '', #13188 ) ; +#67853 = ORIENTED_EDGE ( 'NONE', *, *, #75086, .T. ) ; +#67854 = EDGE_LOOP ( 'NONE', ( #72870, #25450, #26337, #75489 ) ) ; +#67855 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67856 = VERTEX_POINT ( 'NONE', #95458 ) ; +#67857 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67858 = EDGE_CURVE ( 'NONE', #34606, #38779, #4067, .T. ) ; +#67859 = SURFACE_STYLE_FILL_AREA ( #67381 ) ; +#67860 = AXIS2_PLACEMENT_3D ( 'NONE', #16120, #93211, #48339 ) ; +#67862 = ORIENTED_EDGE ( 'NONE', *, *, #83122, .F. ) ; +#67861 = SURFACE_SIDE_STYLE ('',( #27108 ) ) ; +#67863 = AXIS2_PLACEMENT_3D ( 'NONE', #61992, #99649, #28809 ) ; +#67864 = PLANE ( 'NONE', #79257 ) ; +#67865 = CARTESIAN_POINT ( 'NONE', ( 3.256562750249976101, 5.090350750249974077, 0.8648700000000000276 ) ) ; +#67866 = EDGE_LOOP ( 'NONE', ( #68380, #59049, #13014, #86317 ) ) ; +#67867 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67868 = FILL_AREA_STYLE ('',( #20419 ) ) ; +#67869 = VERTEX_POINT ( 'NONE', #43371 ) ; +#67870 = EDGE_CURVE ( 'NONE', #20259, #67581, #11135, .T. ) ; +#67871 = ORIENTED_EDGE ( 'NONE', *, *, #79627, .F. ) ; +#67872 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67873 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.7000000000000005107, -0.02000000000001675091 ) ) ; +#67874 = FILL_AREA_STYLE_COLOUR ( '', #58048 ) ; +#67875 = STYLED_ITEM ( 'NONE', ( #8044 ), #73787 ) ; +#67876 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67877 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#67878 = CARTESIAN_POINT ( 'NONE', ( 9.514457124874956762, 4.008477124874955777, 0.8991599999999999593 ) ) ; +#67879 = CARTESIAN_POINT ( 'NONE', ( 1.525294525926170097, -1.013847726018640039, 0.8299999999999997380 ) ) ; +#67880 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67881 = EDGE_LOOP ( 'NONE', ( #75829, #55435, #78530, #2351 ) ) ; +#67882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67883 = ORIENTED_EDGE ( 'NONE', *, *, #33184, .F. ) ; +#67884 = SURFACE_STYLE_FILL_AREA ( #76568 ) ; +#67885 = FILL_AREA_STYLE ('',( #59807 ) ) ; +#67886 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67888 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#67887 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#67889 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#67890 = FILL_AREA_STYLE ('',( #21955 ) ) ; +#67891 = FILL_AREA_STYLE ('',( #60301 ) ) ; +#67892 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67894 = EDGE_CURVE ( 'NONE', #4944, #81133, #75519, .T. ) ; +#67893 = PRESENTATION_STYLE_ASSIGNMENT (( #5594 ) ) ; +#67895 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #10765 ) ) ; +#67896 = SURFACE_SIDE_STYLE ('',( #46424 ) ) ; +#67897 = FILL_AREA_STYLE_COLOUR ( '', #34692 ) ; +#67898 = PRESENTATION_STYLE_ASSIGNMENT (( #14761 ) ) ; +#67899 = FILL_AREA_STYLE ('',( #20966 ) ) ; +#67900 = VECTOR ( 'NONE', #62531, 1000.000000000000000 ) ; +#67901 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#67902 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#67904 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#67903 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#67905 = LINE ( 'NONE', #74610, #84748 ) ; +#67906 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64237 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17303, #95906, #96406 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67907 = AXIS2_PLACEMENT_3D ( 'NONE', #23370, #63205, #15149 ) ; +#67908 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30024 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75269, #83924, #30266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67909 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60671, 'distance_accuracy_value', 'NONE'); +#67910 = ORIENTED_EDGE ( 'NONE', *, *, #5693, .F. ) ; +#67911 = CARTESIAN_POINT ( 'NONE', ( -1.049664478641080034, -1.428972370004099934, 0.8299999999999999600 ) ) ; +#67912 = EDGE_CURVE ( 'NONE', #55931, #37623, #81203, .T. ) ; +#67913 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92408, #28640, #22481, #59834 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#67914 = EDGE_CURVE ( 'NONE', #98322, #89541, #89834, .T. ) ; +#67916 = VECTOR ( 'NONE', #86642, 1000.000000000000000 ) ; +#67915 = CARTESIAN_POINT ( 'NONE', ( 4.798055499499824350, 3.548857500500174567, 0.8991599999999999593 ) ) ; +#67917 = VECTOR ( 'NONE', #44102, 1000.000000000000000 ) ; +#67918 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#67919 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67920 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#67921 = SURFACE_STYLE_USAGE ( .BOTH. , #44439 ) ; +#67922 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73122 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45000, #85332, #69494 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67923 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#67924 = ORIENTED_EDGE ( 'NONE', *, *, #68399, .F. ) ; +#67925 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67926 = ORIENTED_EDGE ( 'NONE', *, *, #64965, .F. ) ; +#67927 = VECTOR ( 'NONE', #26237, 1000.000000000000000 ) ; +#67928 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01085786437626905937, -0.2434314575050761931 ) ) ; +#67929 = PLANE ( 'NONE', #9043 ) ; +#67930 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 3.500000000000000444, -1.450207831659080759E-157 ) ) ; +#67931 = LINE ( 'NONE', #99004, #51564 ) ; +#67932 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#67934 = EDGE_CURVE ( 'NONE', #85305, #25572, #61082, .T. ) ; +#67933 = VECTOR ( 'NONE', #81845, 1000.000000000000000 ) ; +#67935 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#67936 = FILL_AREA_STYLE_COLOUR ( '', #83603 ) ; +#67937 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#67938 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736765574E-18, 0.8199999999999998401, -0.04999999999999998890 ) ) ; +#67939 = ORIENTED_EDGE ( 'NONE', *, *, #6087, .T. ) ; +#67940 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#67941 = SURFACE_STYLE_FILL_AREA ( #52665 ) ; +#67942 = ORIENTED_EDGE ( 'NONE', *, *, #61781, .F. ) ; +#67943 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#67944 = VERTEX_POINT ( 'NONE', #4554 ) ; +#67945 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67687 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14125, #36678, #28990 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67946 = SURFACE_STYLE_USAGE ( .BOTH. , #4676 ) ; +#67947 = ADVANCED_FACE ( 'NONE', ( #74540 ), #18866, .T. ) ; +#67948 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 13.08073500000000067, 0.8991599999999999593 ) ) ; +#67949 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#67950 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#67952 = VERTEX_POINT ( 'NONE', #13148 ) ; +#67951 = ORIENTED_EDGE ( 'NONE', *, *, #51365, .T. ) ; +#67953 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01085786437626904723, 0.1499999999999999944 ) ) ; +#67954 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#67955 = ORIENTED_EDGE ( 'NONE', *, *, #22025, .F. ) ; +#67956 = STYLED_ITEM ( 'NONE', ( #85010 ), #83902 ) ; +#67957 = VECTOR ( 'NONE', #8058, 1000.000000000000000 ) ; +#67959 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#67958 = PRESENTATION_STYLE_ASSIGNMENT (( #29195 ) ) ; +#67960 = ORIENTED_EDGE ( 'NONE', *, *, #8932, .T. ) ; +#67961 = VECTOR ( 'NONE', #60562, 1000.000000000000000 ) ; +#67962 = ORIENTED_EDGE ( 'NONE', *, *, #22643, .F. ) ; +#67963 = PRESENTATION_STYLE_ASSIGNMENT (( #50700 ) ) ; +#67964 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#67965 = FILL_AREA_STYLE_COLOUR ( '', #54423 ) ; +#67966 = EDGE_CURVE ( 'NONE', #31325, #40383, #65956, .T. ) ; +#67967 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93035 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98577, #42557, #4244 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67969 = FACE_OUTER_BOUND ( 'NONE', #45786, .T. ) ; +#67968 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, -3.099999999999994316, 0.000000000000000000 ) ) ; +#67970 = ORIENTED_EDGE ( 'NONE', *, *, #42148, .F. ) ; +#67971 = ORIENTED_EDGE ( 'NONE', *, *, #15291, .F. ) ; +#67972 = ORIENTED_EDGE ( 'NONE', *, *, #81020, .T. ) ; +#67973 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69649 ), #35464 ) ; +#67974 = EDGE_CURVE ( 'NONE', #39373, #60639, #42389, .T. ) ; +#67975 = VECTOR ( 'NONE', #19643, 1000.000000000000000 ) ; +#67976 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95674 ) ) ; +#67978 = ORIENTED_EDGE ( 'NONE', *, *, #95471, .F. ) ; +#67977 = PLANE ( 'NONE', #62452 ) ; +#67979 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67667, #98756, #44198 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#67980 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82745 ) ) ; +#67981 = FILL_AREA_STYLE_COLOUR ( '', #89793 ) ; +#67982 = FACE_OUTER_BOUND ( 'NONE', #90998, .T. ) ; +#67983 = DIRECTION ( 'NONE', ( -0.7071067811865514585, 0.7071067811865435759, 0.000000000000000000 ) ) ; +#67985 = VECTOR ( 'NONE', #25065, 1000.000000000000000 ) ; +#67984 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#67986 = ORIENTED_EDGE ( 'NONE', *, *, #83056, .F. ) ; +#67987 = DIRECTION ( 'NONE', ( 0.7071072811858626350, -0.7071062811868787934, 0.000000000000000000 ) ) ; +#67988 = CLOSED_SHELL ( 'NONE', ( #97234, #9781, #17962, #22144, #20977, #64065 ) ) ; +#67989 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#67990 = ORIENTED_EDGE ( 'NONE', *, *, #74776, .F. ) ; +#67991 = ADVANCED_FACE ( 'NONE', ( #36730 ), #73524, .T. ) ; +#67992 = STYLED_ITEM ( 'NONE', ( #86524 ), #40153 ) ; +#67993 = SURFACE_STYLE_USAGE ( .BOTH. , #37890 ) ; +#67994 = VECTOR ( 'NONE', #21504, 1000.000000000000000 ) ; +#67996 = VERTEX_POINT ( 'NONE', #30037 ) ; +#67995 = SURFACE_STYLE_FILL_AREA ( #4723 ) ; +#67998 = CARTESIAN_POINT ( 'NONE', ( 1.337707442669689994, -0.9199924700473179895, 0.8299999999999998490 ) ) ; +#67997 = AXIS2_PLACEMENT_3D ( 'NONE', #20937, #67867, #91378 ) ; +#67999 = CARTESIAN_POINT ( 'NONE', ( 1.800644492816920295, -1.399205570841099977, 0.8100000000000000533 ) ) ; +#68001 = CARTESIAN_POINT ( 'NONE', ( 1.496131215532870096, -1.321596304865350069, 0.8100000000000000533 ) ) ; +#68000 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68002 = CARTESIAN_POINT ( 'NONE', ( -1.179651612324215781, -1.146678927717647900, 0.8099999999998799272 ) ) ; +#68003 = SURFACE_STYLE_USAGE ( .BOTH. , #59913 ) ; +#68004 = VERTEX_POINT ( 'NONE', #14183 ) ; +#68005 = CARTESIAN_POINT ( 'NONE', ( -2.676179938779915002, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#68006 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4849999999999999867, -0.2458578643762690530 ) ) ; +#68007 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#68009 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8099999999999112354 ) ) ; +#68008 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#68010 = CARTESIAN_POINT ( 'NONE', ( 3.949527499500047778, 8.130909500499949871, 0.8991599999999999593 ) ) ; +#68011 = AXIS2_PLACEMENT_3D ( 'NONE', #28920, #21760, #53416 ) ; +#68012 = FACE_OUTER_BOUND ( 'NONE', #18082, .T. ) ; +#68013 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68014 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2829 ), #90869 ) ; +#68015 = EDGE_LOOP ( 'NONE', ( #21199, #5062, #52705, #20793 ) ) ; +#68016 = EDGE_CURVE ( 'NONE', #71728, #1854, #63112, .T. ) ; +#68017 = EDGE_CURVE ( 'NONE', #75115, #59960, #84188, .T. ) ; +#68018 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68019 = FACE_BOUND ( 'NONE', #419, .T. ) ; +#68020 = DIRECTION ( 'NONE', ( -1.000000000000000000, -2.305195391370443587E-15, 0.000000000000000000 ) ) ; +#68021 = ORIENTED_EDGE ( 'NONE', *, *, #47579, .T. ) ; +#68022 = LINE ( 'NONE', #67045, #87914 ) ; +#68024 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.499999999999989786, 0.1829999999999999960 ) ) ; +#68023 = SURFACE_STYLE_USAGE ( .BOTH. , #54782 ) ; +#68025 = FACE_OUTER_BOUND ( 'NONE', #78411, .T. ) ; +#68026 = SURFACE_SIDE_STYLE ('',( #29258 ) ) ; +#68027 = CARTESIAN_POINT ( 'NONE', ( -0.7522321428571430157, 0.6899999999999999467, 0.2077922077922079724 ) ) ; +#68028 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72955 ), #19136 ) ; +#68029 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, 0.09999999999999999167, 0.8499999999999999778 ) ) ; +#68030 = LINE ( 'NONE', #26771, #2141 ) ; +#68031 = EDGE_LOOP ( 'NONE', ( #75194, #57572, #31783, #27092, #45467, #57775 ) ) ; +#68032 = LINE ( 'NONE', #92515, #4929 ) ; +#68033 = EDGE_CURVE ( 'NONE', #2547, #49717, #44844, .T. ) ; +#68034 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34626 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86536, #40078, #32421 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68035 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68036 = FILL_AREA_STYLE ('',( #69544 ) ) ; +#68037 = EDGE_CURVE ( 'NONE', #66277, #87953, #94203, .T. ) ; +#68038 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#68039 = FILL_AREA_STYLE ('',( #84876 ) ) ; +#68040 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68041 = SURFACE_SIDE_STYLE ('',( #90551 ) ) ; +#68042 = SURFACE_STYLE_USAGE ( .BOTH. , #69029 ) ; +#68043 = AXIS2_PLACEMENT_3D ( 'NONE', #83989, #37538, #44655 ) ; +#68044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68045 = ADVANCED_FACE ( 'NONE', ( #37729 ), #61230, .F. ) ; +#68046 = FACE_OUTER_BOUND ( 'NONE', #76264, .T. ) ; +#68047 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#68048 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47380 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56507, #1851, #46762 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68049 = STYLED_ITEM ( 'NONE', ( #91049 ), #24397 ) ; +#68050 = FILL_AREA_STYLE_COLOUR ( '', #50419 ) ; +#68051 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90902 ), #27288 ) ; +#68052 = VERTEX_POINT ( 'NONE', #29554 ) ; +#68053 = PLANE ( 'NONE', #67624 ) ; +#68054 = ORIENTED_EDGE ( 'NONE', *, *, #7765, .T. ) ; +#68055 = CARTESIAN_POINT ( 'NONE', ( 1.060148841163599975, -1.043393888298179917, 0.8299999999999999600 ) ) ; +#68057 = VECTOR ( 'NONE', #73252, 1000.000000000000000 ) ; +#68056 = PLANE ( 'NONE', #54680 ) ; +#68058 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68059 = EDGE_CURVE ( 'NONE', #81743, #92365, #53552, .T. ) ; +#68060 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68061 = CARTESIAN_POINT ( 'NONE', ( 1.783955832751769943, -0.9153515042605530061, 0.8299999999999999600 ) ) ; +#68062 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35539 ) ) ; +#68063 = SURFACE_STYLE_USAGE ( .BOTH. , #13907 ) ; +#68064 = CLOSED_SHELL ( 'NONE', ( #14294, #54003, #37763, #53906, #77622, #93281 ) ) ; +#68065 = ORIENTED_EDGE ( 'NONE', *, *, #60055, .F. ) ; +#68066 = SURFACE_STYLE_USAGE ( .BOTH. , #83427 ) ; +#68067 = EDGE_CURVE ( 'NONE', #74000, #72570, #9394, .T. ) ; +#68068 = VECTOR ( 'NONE', #48534, 1000.000000000000000 ) ; +#68069 = SURFACE_STYLE_USAGE ( .BOTH. , #18079 ) ; +#68070 = PRESENTATION_STYLE_ASSIGNMENT (( #75753 ) ) ; +#68071 = ORIENTED_EDGE ( 'NONE', *, *, #200, .T. ) ; +#68073 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#68072 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69674 ) ) ; +#68074 = LINE ( 'NONE', #83926, #39703 ) ; +#68075 = ADVANCED_FACE ( 'NONE', ( #48311 ), #76020, .T. ) ; +#68076 = LINE ( 'NONE', #59492, #76616 ) ; +#68077 = EDGE_CURVE ( 'NONE', #99914, #7099, #2826, .T. ) ; +#68078 = SURFACE_STYLE_FILL_AREA ( #91085 ) ; +#68079 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, -9.880000000000000782, 0.2500000000000000000 ) ) ; +#68080 = ORIENTED_EDGE ( 'NONE', *, *, #24111, .T. ) ; +#68081 = LINE ( 'NONE', #95457, #2567 ) ; +#68083 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19492 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98145, #79011, #71346 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68082 = FILL_AREA_STYLE_COLOUR ( '', #14726 ) ; +#68084 = PRESENTATION_STYLE_ASSIGNMENT (( #36978 ) ) ; +#68085 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#68086 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.123820061220075051, 0.000000000000000000 ) ) ; +#68087 = ORIENTED_EDGE ( 'NONE', *, *, #16702, .F. ) ; +#68088 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#68089 = AXIS2_PLACEMENT_3D ( 'NONE', #15321, #15839, #93436 ) ; +#68090 = DIRECTION ( 'NONE', ( -0.7071067811865472397, 0.7071067811865479058, -1.853151070534223495E-32 ) ) ; +#68091 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68092 = CARTESIAN_POINT ( 'NONE', ( 1.502791041020159923, -1.377680218341670093, 0.8300000000000001821 ) ) ; +#68093 = ORIENTED_EDGE ( 'NONE', *, *, #78443, .F. ) ; +#68094 = VECTOR ( 'NONE', #33549, 1000.000000000000114 ) ; +#68095 = ADVANCED_FACE ( 'NONE', ( #73291 ), #26322, .T. ) ; +#68096 = ORIENTED_EDGE ( 'NONE', *, *, #93731, .T. ) ; +#68098 = ORIENTED_EDGE ( 'NONE', *, *, #72463, .T. ) ; +#68097 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#68099 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58342 ), #6111 ) ; +#68100 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11661, 'distance_accuracy_value', 'NONE'); +#68102 = SURFACE_STYLE_FILL_AREA ( #59524 ) ; +#68101 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68103 = FILL_AREA_STYLE_COLOUR ( '', #33356 ) ; +#68104 = LINE ( 'NONE', #98197, #84587 ) ; +#68105 = ORIENTED_EDGE ( 'NONE', *, *, #871, .T. ) ; +#68106 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68107 = ORIENTED_EDGE ( 'NONE', *, *, #80434, .F. ) ; +#68108 = EDGE_CURVE ( 'NONE', #83060, #69997, #6228, .T. ) ; +#68109 = STYLED_ITEM ( 'NONE', ( #91311 ), #55486 ) ; +#68110 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#68111 = PLANE ( 'NONE', #77366 ) ; +#68112 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68113 = ORIENTED_EDGE ( 'NONE', *, *, #62216, .F. ) ; +#68114 = VECTOR ( 'NONE', #90514, 1000.000000000000000 ) ; +#68115 = EDGE_CURVE ( 'NONE', #93951, #20041, #72260, .T. ) ; +#68116 = CARTESIAN_POINT ( 'NONE', ( 1.794978790831629700, -1.096743473147149928, 0.8099999999999998312 ) ) ; +#68117 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78968, #9933, #24374, #94257 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68118 = VERTEX_POINT ( 'NONE', #64112 ) ; +#68119 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2932 ) ) ; +#68121 = PLANE ( 'NONE', #53250 ) ; +#68120 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#68122 = VECTOR ( 'NONE', #8204, 1000.000000000000000 ) ; +#68123 = STYLED_ITEM ( 'NONE', ( #89303 ), #62632 ) ; +#68125 = EDGE_CURVE ( 'NONE', #27956, #62837, #100040, .T. ) ; +#68124 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#68126 = VECTOR ( 'NONE', #43465, 1000.000000000000114 ) ; +#68127 = LINE ( 'NONE', #30707, #40964 ) ; +#68128 = ORIENTED_EDGE ( 'NONE', *, *, #10899, .F. ) ; +#68129 = ORIENTED_EDGE ( 'NONE', *, *, #84092, .T. ) ; +#68130 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#68131 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11003 ) ) ; +#68132 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68133 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12707 ) ) ; +#68134 = PRESENTATION_STYLE_ASSIGNMENT (( #78348 ) ) ; +#68135 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48663 ) ) ; +#68136 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#68137 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68138 = EDGE_CURVE ( 'NONE', #96933, #92486, #9881, .T. ) ; +#68140 = EDGE_CURVE ( 'NONE', #75434, #82555, #88094, .T. ) ; +#68139 = FILL_AREA_STYLE ('',( #83497 ) ) ; +#68141 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.100000000000000089 ) ) ; +#68142 = FILL_AREA_STYLE_COLOUR ( '', #86968 ) ; +#68143 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#68144 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68145 = EDGE_LOOP ( 'NONE', ( #5213, #96041, #60017, #59664 ) ) ; +#68146 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68147 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#68148 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68151 = PRESENTATION_STYLE_ASSIGNMENT (( #23233 ) ) ; +#68150 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 8.802661000000002289, 0.8648700000000000276 ) ) ; +#68149 = LINE ( 'NONE', #92138, #77255 ) ; +#68152 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22776, 'distance_accuracy_value', 'NONE'); +#68153 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 8.385469000000000506, 0.8648700000000000276 ) ) ; +#68154 = LINE ( 'NONE', #84005, #29961 ) ; +#68155 = LINE ( 'NONE', #84991, #90916 ) ; +#68156 = SURFACE_SIDE_STYLE ('',( #5841 ) ) ; +#68157 = STYLED_ITEM ( 'NONE', ( #34903 ), #75612 ) ; +#68158 = ORIENTED_EDGE ( 'NONE', *, *, #81479, .T. ) ; +#68159 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.62720099999999945, 0.8991599999999999593 ) ) ; +#68160 = EDGE_CURVE ( 'NONE', #81873, #63871, #95708, .T. ) ; +#68161 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#68162 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#68163 = EDGE_CURVE ( 'NONE', #21309, #56090, #58501, .T. ) ; +#68164 = FACE_OUTER_BOUND ( 'NONE', #96655, .T. ) ; +#68165 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#68166 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #3333, .NOT_KNOWN. ) ; +#68167 = LINE ( 'NONE', #67658, #80738 ) ; +#68168 = AXIS2_PLACEMENT_3D ( 'NONE', #39881, #49072, #80222 ) ; +#68169 = FILL_AREA_STYLE ('',( #44682 ) ) ; +#68170 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68171 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#68172 = FILL_AREA_STYLE_COLOUR ( '', #78500 ) ; +#68173 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68174 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89409 ) ) ; +#68175 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#68176 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68177 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, 0.000000000000000000 ) ) ; +#68178 = LINE ( 'NONE', #29401, #51281 ) ; +#68179 = AXIS2_PLACEMENT_3D ( 'NONE', #73655, #34377, #81843 ) ; +#68180 = CARTESIAN_POINT ( 'NONE', ( -0.6761799387799138916, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#68181 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6184 ) ) ; +#68182 = PLANE ( 'NONE', #3814 ) ; +#68183 = SURFACE_STYLE_USAGE ( .BOTH. , #75862 ) ; +#68184 = SURFACE_STYLE_USAGE ( .BOTH. , #22245 ) ; +#68185 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#68186 = ORIENTED_EDGE ( 'NONE', *, *, #12460, .F. ) ; +#68187 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73422 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80045, #11488, #57075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68188 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68189 = ADVANCED_FACE ( 'NONE', ( #41640 ), #19645, .T. ) ; +#68190 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68192 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#68193 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85545, #46205, #7860, #38587 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68194 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17693 ), #37272 ) ; +#68195 = SURFACE_SIDE_STYLE ('',( #59609 ) ) ; +#68197 = EDGE_CURVE ( 'NONE', #24588, #63260, #5788, .T. ) ; +#68196 = SURFACE_STYLE_FILL_AREA ( #59094 ) ; +#68198 = VECTOR ( 'NONE', #99724, 1000.000000000000000 ) ; +#68200 = ADVANCED_FACE ( 'NONE', ( #14445 ), #84435, .T. ) ; +#68199 = SURFACE_SIDE_STYLE ('',( #66705 ) ) ; +#68201 = VECTOR ( 'NONE', #88152, 1000.000000000000000 ) ; +#68202 = VERTEX_POINT ( 'NONE', #75286 ) ; +#68203 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68204 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68205 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79700 ) ) ; +#68206 = VECTOR ( 'NONE', #17608, 1000.000000000000000 ) ; +#68207 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68208 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -9.035018104045849247E-16 ) ) ; +#68209 = VERTEX_POINT ( 'NONE', #20640 ) ; +#68210 = ORIENTED_EDGE ( 'NONE', *, *, #60679, .T. ) ; +#68211 = SURFACE_STYLE_USAGE ( .BOTH. , #59627 ) ; +#68213 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68212 = CARTESIAN_POINT ( 'NONE', ( 0.3985040481619670505, -0.9698512957057280337, 0.8300000000000002931 ) ) ; +#68214 = VERTEX_POINT ( 'NONE', #6265 ) ; +#68215 = SURFACE_SIDE_STYLE ('',( #36615 ) ) ; +#68216 = STYLED_ITEM ( 'NONE', ( #45781 ), #50685 ) ; +#68217 = CARTESIAN_POINT ( 'NONE', ( 0.5453366361084071023, -1.079472621882799910, 0.8100000000000000533 ) ) ; +#68218 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68219 = SURFACE_STYLE_USAGE ( .BOTH. , #52944 ) ; +#68220 = VECTOR ( 'NONE', #13981, 1000.000000000000000 ) ; +#68222 = ORIENTED_EDGE ( 'NONE', *, *, #89315, .F. ) ; +#68221 = EDGE_CURVE ( 'NONE', #35131, #60837, #21646, .T. ) ; +#68223 = STYLED_ITEM ( 'NONE', ( #84286 ), #43985 ) ; +#68224 = VERTEX_POINT ( 'NONE', #51807 ) ; +#68225 = FILL_AREA_STYLE ('',( #59643 ) ) ; +#68226 = PLANE ( 'NONE', #75331 ) ; +#68227 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16397, 'distance_accuracy_value', 'NONE'); +#68229 = FILL_AREA_STYLE_COLOUR ( '', #79058 ) ; +#68228 = CARTESIAN_POINT ( 'NONE', ( 0.3795945119668320267, -0.9004463214819089512, 0.8100000000000000533 ) ) ; +#68230 = ADVANCED_FACE ( 'NONE', ( #35499 ), #82942, .T. ) ; +#68231 = FILL_AREA_STYLE ('',( #37134 ) ) ; +#68232 = CARTESIAN_POINT ( 'NONE', ( -1.370884097750779906, -1.038425069758839969, 0.8299999999999999600 ) ) ; +#68233 = AXIS2_PLACEMENT_3D ( 'NONE', #54541, #15681, #54016 ) ; +#68235 = ORIENTED_EDGE ( 'NONE', *, *, #79329, .T. ) ; +#68234 = AXIS2_PLACEMENT_3D ( 'NONE', #10516, #95863, #25975 ) ; +#68236 = EDGE_CURVE ( 'NONE', #77051, #68559, #97587, .T. ) ; +#68237 = ORIENTED_EDGE ( 'NONE', *, *, #44183, .F. ) ; +#68238 = ORIENTED_EDGE ( 'NONE', *, *, #6636, .T. ) ; +#68239 = CARTESIAN_POINT ( 'NONE', ( 1.172627409212990024, -1.219266740403220028, 0.8100000000000000533 ) ) ; +#68240 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18716 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6969, #44830, #99868 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68241 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68243 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#68242 = SURFACE_STYLE_FILL_AREA ( #66270 ) ; +#68245 = EDGE_CURVE ( 'NONE', #26730, #28071, #94593, .T. ) ; +#68244 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68246 = EDGE_LOOP ( 'NONE', ( #4490, #73032, #60944, #9265 ) ) ; +#68247 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68248 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#68249 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68250 = VECTOR ( 'NONE', #31288, 1000.000000000000000 ) ; +#68251 = VECTOR ( 'NONE', #53140, 1000.000000000000000 ) ; +#68252 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, 0.000000000000000000 ) ) ; +#68253 = FILL_AREA_STYLE_COLOUR ( '', #99437 ) ; +#68254 = ORIENTED_EDGE ( 'NONE', *, *, #27954, .F. ) ; +#68256 = FILL_AREA_STYLE ('',( #37156 ) ) ; +#68255 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#68257 = ORIENTED_EDGE ( 'NONE', *, *, #27679, .T. ) ; +#68258 = ORIENTED_EDGE ( 'NONE', *, *, #91235, .F. ) ; +#68259 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68261 = LINE ( 'NONE', #5939, #17759 ) ; +#68260 = CARTESIAN_POINT ( 'NONE', ( 1.031909709261459973, -1.462480703074420019, 0.8299999999999999600 ) ) ; +#68262 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68263 = VECTOR ( 'NONE', #2067, 1000.000000000000000 ) ; +#68264 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46997 ), #73198 ) ; +#68265 = LINE ( 'NONE', #74957, #84163 ) ; +#68266 = SURFACE_STYLE_FILL_AREA ( #5450 ) ; +#68267 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8199999999999999512 ) ) ; +#68268 = EDGE_CURVE ( 'NONE', #55021, #92216, #24194, .T. ) ; +#68269 = ADVANCED_FACE ( 'NONE', ( #39479 ), #16989, .F. ) ; +#68270 = FILL_AREA_STYLE ('',( #100805 ) ) ; +#68271 = STYLED_ITEM ( 'NONE', ( #38646 ), #17962 ) ; +#68272 = ORIENTED_EDGE ( 'NONE', *, *, #65880, .F. ) ; +#68273 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40554 ) ) ; +#68274 = AXIS2_PLACEMENT_3D ( 'NONE', #75249, #21113, #57958 ) ; +#68275 = ORIENTED_EDGE ( 'NONE', *, *, #3544, .F. ) ; +#68276 = CIRCLE ( 'NONE', #79764, 0.2299999999877400114 ) ; +#68277 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#68278 = CARTESIAN_POINT ( 'NONE', ( -0.007896400202255349221, -1.058723197808659977, 0.8299999999999999600 ) ) ; +#68279 = EDGE_CURVE ( 'NONE', #77186, #16240, #8256, .T. ) ; +#68280 = CARTESIAN_POINT ( 'NONE', ( 1.075908802260020058, -1.102553831183370026, 0.8100000000000000533 ) ) ; +#68281 = AXIS2_PLACEMENT_3D ( 'NONE', #48288, #32445, #80941 ) ; +#68282 = LINE ( 'NONE', #83129, #85498 ) ; +#68283 = FILL_AREA_STYLE_COLOUR ( '', #40270 ) ; +#68284 = STYLED_ITEM ( 'NONE', ( #60287 ), #514 ) ; +#68285 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#68286 = ORIENTED_EDGE ( 'NONE', *, *, #69784, .T. ) ; +#68287 = SURFACE_STYLE_USAGE ( .BOTH. , #13603 ) ; +#68288 = SURFACE_SIDE_STYLE ('',( #91766 ) ) ; +#68289 = ADVANCED_FACE ( 'NONE', ( #62999 ), #16460, .T. ) ; +#68290 = PLANE ( 'NONE', #16966 ) ; +#68291 = PRESENTATION_STYLE_ASSIGNMENT (( #14136 ) ) ; +#68292 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#68293 = FILL_AREA_STYLE ('',( #69261 ) ) ; +#68294 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#68295 = VECTOR ( 'NONE', #26763, 1000.000000000000000 ) ; +#68296 = ADVANCED_FACE ( 'NONE', ( #26204 ), #34873, .T. ) ; +#68297 = SURFACE_STYLE_USAGE ( .BOTH. , #29511 ) ; +#68299 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45331 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45186, #84030, #98266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68298 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68300 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 1.633333333333333304, 0.000000000000000000 ) ) ; +#68301 = SURFACE_STYLE_FILL_AREA ( #66804 ) ; +#68302 = LINE ( 'NONE', #99365, #9522 ) ; +#68303 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68304 = FILL_AREA_STYLE ('',( #37204 ) ) ; +#68305 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81410 ), #21028 ) ; +#68306 = FACE_OUTER_BOUND ( 'NONE', #46707, .T. ) ; +#68307 = VERTEX_POINT ( 'NONE', #32838 ) ; +#68308 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 2.877107000000000081, 0.8991599999999999593 ) ) ; +#68309 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#68310 = CARTESIAN_POINT ( 'NONE', ( -0.9350147092242558911, -1.061283632817223044, 0.8099999999999428768 ) ) ; +#68311 = ORIENTED_EDGE ( 'NONE', *, *, #79329, .F. ) ; +#68312 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68313 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68314 = LINE ( 'NONE', #21358, #13700 ) ; +#68315 = PRESENTATION_STYLE_ASSIGNMENT (( #81678 ) ) ; +#68316 = FACE_OUTER_BOUND ( 'NONE', #84600, .T. ) ; +#68317 = VECTOR ( 'NONE', #4403, 1000.000000000000000 ) ; +#68318 = CIRCLE ( 'NONE', #76487, 0.01000000000000002623 ) ; +#68319 = SURFACE_SIDE_STYLE ('',( #37218 ) ) ; +#68320 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#68321 = SURFACE_STYLE_FILL_AREA ( #18461 ) ; +#68322 = AXIS2_PLACEMENT_3D ( 'NONE', #82964, #83957, #81972 ) ; +#68323 = VECTOR ( 'NONE', #59076, 1000.000000000000000 ) ; +#68324 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, 0.1350000000000000089 ) ) ; +#68325 = EDGE_LOOP ( 'NONE', ( #36548, #92707, #6539, #88730 ) ) ; +#68326 = EDGE_CURVE ( 'NONE', #55494, #96832, #95085, .T. ) ; +#68327 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#68328 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78117 ) ) ; +#68329 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68330 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83005 ) ) ; +#68331 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73262 ) ) ; +#68332 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#68333 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68334 = EDGE_CURVE ( 'NONE', #10916, #19915, #33867, .T. ) ; +#68335 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_ESP32-S3_20210301.STEP', ( #51809, #7674 ), #25725 ) ; +#68336 = VECTOR ( 'NONE', #92291, 1000.000000000000000 ) ; +#68338 = FILL_AREA_STYLE ('',( #91334 ) ) ; +#68337 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68339 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35817 ) ) ; +#68340 = ORIENTED_EDGE ( 'NONE', *, *, #77302, .F. ) ; +#68341 = EDGE_LOOP ( 'NONE', ( #45953, #5430, #969, #28956 ) ) ; +#68342 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68343 = VERTEX_POINT ( 'NONE', #96098 ) ; +#68344 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.699999999999999512, 0.1829999999999540328 ) ) ; +#68345 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68346 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68347 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#68348 = SHAPE_DEFINITION_REPRESENTATION ( #88936, #89242 ) ; +#68349 = CARTESIAN_POINT ( 'NONE', ( -0.2714932316793902678, 1.150801384564331453, 0.8100000000000002753 ) ) ; +#68350 = AXIS2_PLACEMENT_3D ( 'NONE', #9979, #39034, #70667 ) ; +#68353 = ORIENTED_EDGE ( 'NONE', *, *, #71988, .T. ) ; +#68352 = ORIENTED_EDGE ( 'NONE', *, *, #8932, .F. ) ; +#68351 = ADVANCED_FACE ( 'NONE', ( #88980 ), #95588, .T. ) ; +#68354 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94439 ) ) ; +#68355 = ORIENTED_EDGE ( 'NONE', *, *, #57012, .T. ) ; +#68356 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36709, 'distance_accuracy_value', 'NONE'); +#68358 = LINE ( 'NONE', #44362, #31669 ) ; +#68357 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.09999999999999853451, 0.1829999999999749605 ) ) ; +#68359 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79623 ) ) ; +#68360 = VERTEX_POINT ( 'NONE', #56853 ) ; +#68362 = EDGE_CURVE ( 'NONE', #14332, #49661, #58375, .T. ) ; +#68361 = ORIENTED_EDGE ( 'NONE', *, *, #83620, .T. ) ; +#68363 = FILL_AREA_STYLE_COLOUR ( '', #75693 ) ; +#68365 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68364 = LINE ( 'NONE', #83715, #39943 ) ; +#68366 = LINE ( 'NONE', #29575, #67110 ) ; +#68367 = STYLED_ITEM ( 'NONE', ( #62818 ), #51064 ) ; +#68368 = ORIENTED_EDGE ( 'NONE', *, *, #26045, .F. ) ; +#68369 = ORIENTED_EDGE ( 'NONE', *, *, #68417, .T. ) ; +#68370 = ORIENTED_EDGE ( 'NONE', *, *, #482, .F. ) ; +#68371 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92317 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20486, #83796, #74629 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68372 = FACE_OUTER_BOUND ( 'NONE', #33116, .T. ) ; +#68373 = EDGE_CURVE ( 'NONE', #33538, #80630, #27716, .T. ) ; +#68375 = ORIENTED_EDGE ( 'NONE', *, *, #38667, .F. ) ; +#68374 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68376 = SURFACE_STYLE_FILL_AREA ( #35781 ) ; +#68377 = ORIENTED_EDGE ( 'NONE', *, *, #69620, .F. ) ; +#68378 = ORIENTED_EDGE ( 'NONE', *, *, #59104, .F. ) ; +#68379 = EDGE_CURVE ( 'NONE', #100207, #26348, #90473, .T. ) ; +#68380 = ORIENTED_EDGE ( 'NONE', *, *, #41946, .F. ) ; +#68381 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.297402597402600000, 0.8100000000000000533 ) ) ; +#68382 = VECTOR ( 'NONE', #87559, 1000.000000000000000 ) ; +#68383 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68385 = ADVANCED_FACE ( 'NONE', ( #50701 ), #29680, .T. ) ; +#68384 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #79572, #10504 ), + ( #64739, #65238 ), + ( #11025, #25965 ), + ( #17249, #1960 ), + ( #81092, #47911 ), + ( #41772, #57622 ), + ( #72910, #88720 ), + ( #94839, #49949 ), + ( #26960, #79064 ), + ( #9018, #40265 ), + ( #1458, #52441 ), + ( #13545, #12549 ), + ( #90731, #75911 ), + ( #67730, #43755 ), + ( #27974, #19265 ), + ( #4935, #82092 ), + ( #68228, #66733 ), + ( #51953, #20784 ), + ( #44740, #21280 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07233520380446670228, 0.1406164208698900131, 0.2058568734728750127, 0.2690756830016319823, 0.3300877397612519970, 0.3891610552472329898, 0.4474756408581599954, 0.5052403664210020073, 0.5634152235309070056, 0.6220285514472370103, 0.6815091249882340163, 0.7429780954347050548, 0.8053640459471179680, 0.8691057565010430475, 0.9336642540648779631, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68387 = ADVANCED_FACE ( 'NONE', ( #83330 ), #83829, .T. ) ; +#68386 = FILL_AREA_STYLE ('',( #30090 ) ) ; +#68388 = CARTESIAN_POINT ( 'NONE', ( 1.347523492357600050, -1.285676881280640282, 0.8299999999999997380 ) ) ; +#68389 = VECTOR ( 'NONE', #33222, 1000.000000000000000 ) ; +#68390 = STYLED_ITEM ( 'NONE', ( #47931 ), #93232 ) ; +#68391 = SURFACE_SIDE_STYLE ('',( #13720 ) ) ; +#68392 = VECTOR ( 'NONE', #9354, 1000.000000000000000 ) ; +#68393 = PLANE ( 'NONE', #42628 ) ; +#68394 = ORIENTED_EDGE ( 'NONE', *, *, #41597, .T. ) ; +#68395 = PRESENTATION_STYLE_ASSIGNMENT (( #30093 ) ) ; +#68396 = ORIENTED_EDGE ( 'NONE', *, *, #83980, .T. ) ; +#68398 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#68397 = STYLED_ITEM ( 'NONE', ( #25599 ), #57378 ) ; +#68399 = EDGE_CURVE ( 'NONE', #20105, #81116, #17316, .T. ) ; +#68400 = FILL_AREA_STYLE ('',( #78095 ) ) ; +#68401 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37464 ) ) ; +#68402 = AXIS2_PLACEMENT_3D ( 'NONE', #55318, #39965, #72121 ) ; +#68403 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68405 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68404 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99150 ), #29358 ) ; +#68406 = CARTESIAN_POINT ( 'NONE', ( 1.739573088979520010, -1.154690592117219916, 0.8100000000000000533 ) ) ; +#68407 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68408 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68409 = CARTESIAN_POINT ( 'NONE', ( -1.390280071815130025, -1.351356007592219965, 0.8300000000000024025 ) ) ; +#68410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57092 ), #50542 ) ; +#68411 = PRESENTATION_STYLE_ASSIGNMENT (( #85743 ) ) ; +#68412 = ADVANCED_FACE ( 'NONE', ( #68482 ), #4206, .T. ) ; +#68413 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68414 = FACE_OUTER_BOUND ( 'NONE', #12690, .T. ) ; +#68415 = VECTOR ( 'NONE', #80267, 1000.000000000000000 ) ; +#68416 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68417 = EDGE_CURVE ( 'NONE', #33665, #81543, #7476, .T. ) ; +#68418 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68419 = VECTOR ( 'NONE', #48220, 1000.000000000000000 ) ; +#68420 = SURFACE_STYLE_FILL_AREA ( #86005 ) ; +#68421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81661 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31515, #24393, #56034 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68422 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#68423 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19768 ), #70099 ) ; +#68424 = ORIENTED_EDGE ( 'NONE', *, *, #98404, .F. ) ; +#68425 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#68426 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46148, 'distance_accuracy_value', 'NONE'); +#68427 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79634, 'distance_accuracy_value', 'NONE'); +#68428 = SURFACE_STYLE_FILL_AREA ( #5614 ) ; +#68429 = FILL_AREA_STYLE_COLOUR ( '', #18374 ) ; +#68430 = LINE ( 'NONE', #99489, #92384 ) ; +#68431 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#68432 = DIRECTION ( 'NONE', ( 0.000000000000000000, 3.357926749866047180E-13, 1.000000000000000000 ) ) ; +#68433 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68434 = LINE ( 'NONE', #90939, #71443 ) ; +#68435 = VERTEX_POINT ( 'NONE', #30672 ) ; +#68436 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#68437 = VERTEX_POINT ( 'NONE', #47526 ) ; +#68438 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#68439 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55050, 'distance_accuracy_value', 'NONE'); +#68440 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69133, 'distance_accuracy_value', 'NONE'); +#68441 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3242 ), #40786 ) ; +#68442 = FACE_OUTER_BOUND ( 'NONE', #26431, .T. ) ; +#68443 = CYLINDRICAL_SURFACE ( 'NONE', #8733, 0.05000000000000012768 ) ; +#68444 = CARTESIAN_POINT ( 'NONE', ( -0.1271088354660659947, -0.9625852181168450539, 0.8100000000000000533 ) ) ; +#68445 = FILL_AREA_STYLE ('',( #45942 ) ) ; +#68446 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68447 = SURFACE_SIDE_STYLE ('',( #37351 ) ) ; +#68448 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, -0.1400000000000000411 ) ) ; +#68449 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.300000000000000266, 0.000000000000000000 ) ) ; +#68450 = ADVANCED_FACE ( 'NONE', ( #23056 ), #47022, .T. ) ; +#68451 = ORIENTED_EDGE ( 'NONE', *, *, #67079, .T. ) ; +#68452 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#68453 = PRESENTATION_STYLE_ASSIGNMENT (( #6121 ) ) ; +#68454 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68455 = ORIENTED_EDGE ( 'NONE', *, *, #92197, .T. ) ; +#68456 = SURFACE_SIDE_STYLE ('',( #22004 ) ) ; +#68457 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68458 = ORIENTED_EDGE ( 'NONE', *, *, #23472, .T. ) ; +#68459 = SURFACE_SIDE_STYLE ('',( #52180 ) ) ; +#68460 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68461 = AXIS2_PLACEMENT_3D ( 'NONE', #100408, #38749, #33636 ) ; +#68462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43993 ), #84724 ) ; +#68463 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68464 = CARTESIAN_POINT ( 'NONE', ( 1.864761241546880166, -1.121240070007210043, 0.8299999999999999600 ) ) ; +#68465 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #43030, #89993, #3730, #34902 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68466 = CARTESIAN_POINT ( 'NONE', ( -0.6687297077922079724, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#68468 = ORIENTED_EDGE ( 'NONE', *, *, #27868, .T. ) ; +#68467 = ORIENTED_EDGE ( 'NONE', *, *, #74406, .T. ) ; +#68469 = AXIS2_PLACEMENT_3D ( 'NONE', #35289, #28584, #66393 ) ; +#68470 = FILL_AREA_STYLE_COLOUR ( '', #92930 ) ; +#68471 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96162 ) ) ; +#68472 = CIRCLE ( 'NONE', #78038, 0.01000000000000002623 ) ; +#68473 = ORIENTED_EDGE ( 'NONE', *, *, #1929, .T. ) ; +#68474 = STYLED_ITEM ( 'NONE', ( #38405 ), #94063 ) ; +#68475 = VECTOR ( 'NONE', #24059, 1000.000000000000000 ) ; +#68477 = CARTESIAN_POINT ( 'NONE', ( -0.5701283358897649700, -0.9702412545157700352, 0.8100000000000000533 ) ) ; +#68476 = FACE_OUTER_BOUND ( 'NONE', #76660, .T. ) ; +#68478 = ORIENTED_EDGE ( 'NONE', *, *, #6558, .F. ) ; +#68479 = ORIENTED_EDGE ( 'NONE', *, *, #62917, .F. ) ; +#68480 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44072 ), #57167 ) ; +#68481 = FACE_OUTER_BOUND ( 'NONE', #82580, .T. ) ; +#68482 = FACE_OUTER_BOUND ( 'NONE', #84705, .T. ) ; +#68483 = STYLED_ITEM ( 'NONE', ( #93873 ), #80741 ) ; +#68484 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#68486 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68485 = FILL_AREA_STYLE ('',( #99047 ) ) ; +#68487 = STYLED_ITEM ( 'NONE', ( #87900 ), #65068 ) ; +#68488 = ORIENTED_EDGE ( 'NONE', *, *, #55115, .T. ) ; +#68489 = ORIENTED_EDGE ( 'NONE', *, *, #68245, .F. ) ; +#68490 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68491 = ORIENTED_EDGE ( 'NONE', *, *, #75212, .T. ) ; +#68492 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100101 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60181, #13086, #36178 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68493 = VECTOR ( 'NONE', #36566, 1000.000000000000000 ) ; +#68494 = VECTOR ( 'NONE', #19272, 1000.000000000000114 ) ; +#68496 = ORIENTED_EDGE ( 'NONE', *, *, #99772, .T. ) ; +#68495 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68497 = VECTOR ( 'NONE', #70051, 1000.000000000000000 ) ; +#68498 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.000000000000000000, 0.3000000000000000999 ) ) ; +#68499 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68500 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68501 = LINE ( 'NONE', #45490, #52116 ) ; +#68502 = ORIENTED_EDGE ( 'NONE', *, *, #97900, .T. ) ; +#68503 = PLANE ( 'NONE', #95623 ) ; +#68504 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#68505 = ORIENTED_EDGE ( 'NONE', *, *, #18628, .T. ) ; +#68506 = SURFACE_STYLE_FILL_AREA ( #37408 ) ; +#68507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68508 = CIRCLE ( 'NONE', #49017, 0.09999999999999999167 ) ; +#68510 = VERTEX_POINT ( 'NONE', #1066 ) ; +#68509 = PRESENTATION_STYLE_ASSIGNMENT (( #60404 ) ) ; +#68511 = CARTESIAN_POINT ( 'NONE', ( 1.380164001837510090, -0.9588323859052130249, 0.8299999999999998490 ) ) ; +#68512 = PLANE ( 'NONE', #14464 ) ; +#68513 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68514 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#68515 = FILL_AREA_STYLE_COLOUR ( '', #88689 ) ; +#68516 = ORIENTED_EDGE ( 'NONE', *, *, #23425, .F. ) ; +#68517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56187 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80192, #72494, #95567 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68518 = SURFACE_STYLE_FILL_AREA ( #6670 ) ; +#68519 = ADVANCED_FACE ( 'NONE', ( #93943 ), #24073, .T. ) ; +#68521 = CARTESIAN_POINT ( 'NONE', ( 1.347355563172373483, -1.394896464896022259, 0.8099999999997413713 ) ) ; +#68520 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#68522 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68523 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68524 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68525 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999986226, 0.1400000000000000133 ) ) ; +#68526 = EDGE_LOOP ( 'NONE', ( #26422, #33190, #10985, #66266 ) ) ; +#68527 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68528 = EDGE_CURVE ( 'NONE', #82982, #45746, #2092, .T. ) ; +#68529 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73098 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49446, #10034, #80602 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68530 = VERTEX_POINT ( 'NONE', #48566 ) ; +#68531 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52327 ), #36006 ) ; +#68532 = FACE_OUTER_BOUND ( 'NONE', #19620, .T. ) ; +#68534 = LINE ( 'NONE', #92023, #47773 ) ; +#68533 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#68535 = VECTOR ( 'NONE', #29471, 1000.000000000000000 ) ; +#68536 = SURFACE_SIDE_STYLE ('',( #53251 ) ) ; +#68537 = CIRCLE ( 'NONE', #19661, 0.02999999999999997113 ) ; +#68538 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94533 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19946, #44403, #21440 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68539 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#68540 = STYLED_ITEM ( 'NONE', ( #95967 ), #81816 ) ; +#68541 = VERTEX_POINT ( 'NONE', #81220 ) ; +#68542 = SURFACE_SIDE_STYLE ('',( #99114 ) ) ; +#68543 = FILL_AREA_STYLE_COLOUR ( '', #44155 ) ; +#68544 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68545 = SURFACE_STYLE_FILL_AREA ( #91541 ) ; +#68546 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68547 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.000000000000000000 ) ) ; +#68548 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#68549 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49255 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78868, #8833, #40077 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68550 = LINE ( 'NONE', #67544, #41999 ) ; +#68551 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#68552 = SURFACE_STYLE_USAGE ( .BOTH. , #90042 ) ; +#68553 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11827, 'distance_accuracy_value', 'NONE'); +#68554 = ADVANCED_FACE ( 'NONE', ( #56740 ), #17879, .T. ) ; +#68555 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000533, 0.000000000000000000 ) ) ; +#68556 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97901 ) ) ; +#68557 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#68558 = VERTEX_POINT ( 'NONE', #63878 ) ; +#68559 = VERTEX_POINT ( 'NONE', #41899 ) ; +#68560 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68562 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49805, 'distance_accuracy_value', 'NONE'); +#68561 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68563 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20843, 'distance_accuracy_value', 'NONE'); +#68564 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68565 = LINE ( 'NONE', #60949, #2553 ) ; +#68566 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68567 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68568 = SURFACE_STYLE_FILL_AREA ( #91561 ) ; +#68569 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.1499999999999999944, 0.08229670385730990245 ) ) ; +#68570 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.6761799387799151129, -0.02000000000000000042 ) ) ; +#68571 = SURFACE_STYLE_FILL_AREA ( #4784 ) ; +#68572 = EDGE_CURVE ( 'NONE', #13836, #2961, #57514, .T. ) ; +#68573 = ORIENTED_EDGE ( 'NONE', *, *, #38828, .T. ) ; +#68574 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#68575 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32263, 'distance_accuracy_value', 'NONE'); +#68576 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000971, 0.2400000000000000189 ) ) ; +#68577 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#68578 = STYLED_ITEM ( 'NONE', ( #35463 ), #51582 ) ; +#68579 = ORIENTED_EDGE ( 'NONE', *, *, #39390, .T. ) ; +#68580 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34456 ), #32756 ) ; +#68581 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#68582 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8991599999999999593 ) ) ; +#68583 = CARTESIAN_POINT ( 'NONE', ( -1.316686852848500067, -1.306787212278190058, 0.8100000000000000533 ) ) ; +#68584 = LINE ( 'NONE', #36479, #31817 ) ; +#68585 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68586 = ORIENTED_EDGE ( 'NONE', *, *, #54602, .T. ) ; +#68587 = FACE_OUTER_BOUND ( 'NONE', #62731, .T. ) ; +#68588 = AXIS2_PLACEMENT_3D ( 'NONE', #72490, #79681, #20761 ) ; +#68589 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46693, 'distance_accuracy_value', 'NONE'); +#68590 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68591 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71086, #1127, #55778, #7190, #31770, #45528, #92517, #8200, #93000, #32288, #6690, #94537, #24656, #38933, #78251, #70564, #54790 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.217060269204687310E-05, 4.373712411657698602E-05, 5.438460671129726333E-05, 6.481866320469777207E-05, 7.490038279277603779E-05, 8.498210238085428996E-05, 9.503964954003555027E-05, 0.0001051177103656679982, 0.0001153266605817813327, 0.0001258150082380591478, 0.0001366635663297261188, 0.0001477422118352538969, 0.0001591650473074330478, 0.0001710833825230662162 ), + .UNSPECIFIED. ) ; +#68592 = SURFACE_SIDE_STYLE ('',( #36982 ) ) ; +#68593 = SURFACE_STYLE_FILL_AREA ( #9640 ) ; +#68594 = VERTEX_POINT ( 'NONE', #72035 ) ; +#68595 = AXIS2_PLACEMENT_3D ( 'NONE', #51359, #67145, #88624 ) ; +#68596 = STYLED_ITEM ( 'NONE', ( #47642 ), #33802 ) ; +#68597 = PLANE ( 'NONE', #91847 ) ; +#68598 = CARTESIAN_POINT ( 'NONE', ( 1.076179938779914913, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#68599 = CARTESIAN_POINT ( 'NONE', ( 1.673324881778589956, -1.507258815139120189, 0.8300000000000001821 ) ) ; +#68600 = EDGE_LOOP ( 'NONE', ( #292, #23842, #71220, #4570 ) ) ; +#68601 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68602 = EDGE_CURVE ( 'NONE', #48689, #26002, #26084, .T. ) ; +#68603 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #11891 ) ; +#68604 = STYLED_ITEM ( 'NONE', ( #204 ), #86305 ) ; +#68605 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79952 ) ) ; +#68606 = VECTOR ( 'NONE', #33944, 1000.000000000000000 ) ; +#68607 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46750 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36535, #91136, #62912 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68608 = ORIENTED_EDGE ( 'NONE', *, *, #68160, .F. ) ; +#68610 = ORIENTED_EDGE ( 'NONE', *, *, #72679, .F. ) ; +#68609 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68611 = VECTOR ( 'NONE', #50859, 1000.000000000000114 ) ; +#68612 = CARTESIAN_POINT ( 'NONE', ( -1.154835151445229968, -1.515412412365080064, 0.8299999999999999600 ) ) ; +#68613 = FILL_AREA_STYLE_COLOUR ( '', #12120 ) ; +#68614 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#68615 = VERTEX_POINT ( 'NONE', #94971 ) ; +#68616 = PLANE ( 'NONE', #68322 ) ; +#68617 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68618 = ORIENTED_EDGE ( 'NONE', *, *, #92288, .F. ) ; +#68619 = ADVANCED_FACE ( 'NONE', ( #26582 ), #95475, .F. ) ; +#68620 = CARTESIAN_POINT ( 'NONE', ( 1.395857244856030022, -1.450479623942970253, 0.8299999999999999600 ) ) ; +#68621 = EDGE_CURVE ( 'NONE', #66638, #39853, #21410, .T. ) ; +#68622 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#68623 = ORIENTED_EDGE ( 'NONE', *, *, #2286, .T. ) ; +#68624 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78414 ) ) ; +#68625 = LINE ( 'NONE', #29827, #22511 ) ; +#68626 = ORIENTED_EDGE ( 'NONE', *, *, #26860, .F. ) ; +#68628 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#68627 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#68629 = VECTOR ( 'NONE', #45520, 1000.000000000000000 ) ; +#68630 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -2.966666666666666785, 0.000000000000000000 ) ) ; +#68631 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55639 ) ) ; +#68632 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68633 = CARTESIAN_POINT ( 'NONE', ( 0.2846257902759590230, -1.272935805450750246, 0.8299999999999982947 ) ) ; +#68634 = EDGE_CURVE ( 'NONE', #91804, #2565, #4572, .T. ) ; +#68635 = ORIENTED_EDGE ( 'NONE', *, *, #74037, .F. ) ; +#68636 = ORIENTED_EDGE ( 'NONE', *, *, #52123, .T. ) ; +#68637 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77880 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2489, #33650, #79097 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68638 = CYLINDRICAL_SURFACE ( 'NONE', #6922, 0.009999999999999998473 ) ; +#68639 = FILL_AREA_STYLE ('',( #74821 ) ) ; +#68640 = SURFACE_SIDE_STYLE ('',( #37036 ) ) ; +#68641 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68642 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.7000000000000018430, -1.195472123049164304E-89 ) ) ; +#68643 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68644 = LINE ( 'NONE', #45640, #87836 ) ; +#68645 = FILL_AREA_STYLE ('',( #68142 ) ) ; +#68646 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68647 = ADVANCED_FACE ( 'NONE', ( #74039 ), #98432, .T. ) ; +#68648 = SURFACE_STYLE_USAGE ( .BOTH. , #77318 ) ; +#68649 = VERTEX_POINT ( 'NONE', #28091 ) ; +#68650 = FILL_AREA_STYLE_COLOUR ( '', #51453 ) ; +#68651 = CARTESIAN_POINT ( 'NONE', ( -5.421010862427522170E-17, 0.2999999999815373686, -1.665334536835250932E-17 ) ) ; +#68653 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68652 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68654 = VECTOR ( 'NONE', #16088, 1000.000000000000000 ) ; +#68655 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68656 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#68657 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68658 = ORIENTED_EDGE ( 'NONE', *, *, #46994, .T. ) ; +#68659 = FILL_AREA_STYLE ('',( #14007 ) ) ; +#68660 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68661 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#68662 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68663 = VECTOR ( 'NONE', #65513, 1000.000000000000000 ) ; +#68664 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68665 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#68666 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21194, 'distance_accuracy_value', 'NONE'); +#68667 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68668 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68669 = SURFACE_SIDE_STYLE ('',( #76342 ) ) ; +#68670 = AXIS2_PLACEMENT_3D ( 'NONE', #39911, #44281, #3997 ) ; +#68671 = LINE ( 'NONE', #75849, #44235 ) ; +#68672 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19966 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40075, #33438, #34451 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68674 = EDGE_CURVE ( 'NONE', #36002, #78277, #59420, .T. ) ; +#68675 = CARTESIAN_POINT ( 'NONE', ( -0.1500000000000000222, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#68676 = VECTOR ( 'NONE', #36131, 1000.000000000000000 ) ; +#68677 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68678 = FACE_OUTER_BOUND ( 'NONE', #74397, .T. ) ; +#68679 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79407, 'distance_accuracy_value', 'NONE'); +#68680 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68681 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68682 = LINE ( 'NONE', #67681, #6272 ) ; +#68683 = SURFACE_STYLE_USAGE ( .BOTH. , #92177 ) ; +#68684 = FILL_AREA_STYLE_COLOUR ( '', #71634 ) ; +#68685 = ADVANCED_FACE ( 'NONE', ( #97487 ), #12685, .T. ) ; +#68686 = EDGE_LOOP ( 'NONE', ( #84011, #56195, #57729, #84616 ) ) ; +#68687 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23101 ) ) ; +#68688 = PRESENTATION_STYLE_ASSIGNMENT (( #93657 ) ) ; +#68689 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15300, 'distance_accuracy_value', 'NONE'); +#68690 = SURFACE_STYLE_FILL_AREA ( #45689 ) ; +#68691 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68692 = STYLED_ITEM ( 'NONE', ( #77885 ), #20945 ) ; +#68693 = EDGE_CURVE ( 'NONE', #81483, #47689, #98930, .T. ) ; +#68694 = ORIENTED_EDGE ( 'NONE', *, *, #88790, .T. ) ; +#68695 = LINE ( 'NONE', #51914, #24743 ) ; +#68696 = PLANE ( 'NONE', #41337 ) ; +#68697 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8648700000000000276 ) ) ; +#68698 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8099999999999885070 ) ) ; +#68699 = PRESENTATION_STYLE_ASSIGNMENT (( #14046 ) ) ; +#68701 = ORIENTED_EDGE ( 'NONE', *, *, #2266, .T. ) ; +#68700 = AXIS2_PLACEMENT_3D ( 'NONE', #94091, #22680, #85965 ) ; +#68702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28312, 'distance_accuracy_value', 'NONE'); +#68703 = LINE ( 'NONE', #91690, #49169 ) ; +#68704 = EDGE_LOOP ( 'NONE', ( #21215, #70872, #81183, #66370 ) ) ; +#68705 = VERTEX_POINT ( 'NONE', #76037 ) ; +#68706 = ORIENTED_EDGE ( 'NONE', *, *, #31365, .F. ) ; +#68707 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68708 = SURFACE_SIDE_STYLE ('',( #46741 ) ) ; +#68709 = CARTESIAN_POINT ( 'NONE', ( 0.5426878470553200273, -1.110278784363659899, 0.8100000000000000533 ) ) ; +#68710 = FILL_AREA_STYLE_COLOUR ( '', #20398 ) ; +#68712 = ADVANCED_FACE ( 'NONE', ( #69334 ), #38248, .T. ) ; +#68711 = VECTOR ( 'NONE', #97351, 1000.000000000000000 ) ; +#68713 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959499, 1.048695503451053346E-76 ) ) ; +#68714 = EDGE_CURVE ( 'NONE', #6846, #85582, #77039, .T. ) ; +#68715 = ORIENTED_EDGE ( 'NONE', *, *, #8307, .F. ) ; +#68716 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76865 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1170, #48161, #78298 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68717 = VERTEX_POINT ( 'NONE', #16228 ) ; +#68718 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#68719 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#68720 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#68721 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.499999999999960032, -0.02000000000000000042 ) ) ; +#68722 = EDGE_CURVE ( 'NONE', #61697, #95346, #21912, .T. ) ; +#68723 = DIRECTION ( 'NONE', ( -1.000000000000000000, -6.165170508236908981E-73, -4.720272329281459820E-44 ) ) ; +#68724 = SURFACE_STYLE_FILL_AREA ( #5915 ) ; +#68725 = EDGE_CURVE ( 'NONE', #20063, #17177, #54070, .T. ) ; +#68726 = AXIS2_PLACEMENT_3D ( 'NONE', #27137, #18427, #57798 ) ; +#68727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99261 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59246, #65868, #12148 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68728 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68729 = ORIENTED_EDGE ( 'NONE', *, *, #40846, .T. ) ; +#68730 = ADVANCED_FACE ( 'NONE', ( #31078 ), #86202, .T. ) ; +#68731 = FILL_AREA_STYLE ('',( #100774 ) ) ; +#68732 = ORIENTED_EDGE ( 'NONE', *, *, #76081, .T. ) ; +#68733 = EDGE_LOOP ( 'NONE', ( #28150, #72053, #99799, #59399 ) ) ; +#68734 = CARTESIAN_POINT ( 'NONE', ( 1.328303542420389949, -1.268071887441960088, 0.8100000000000000533 ) ) ; +#68735 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68736 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#68738 = PLANE ( 'NONE', #66223 ) ; +#68737 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#68739 = PLANE ( 'NONE', #50657 ) ; +#68740 = SURFACE_STYLE_USAGE ( .BOTH. , #74939 ) ; +#68741 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55750 ), #10078 ) ; +#68743 = ORIENTED_EDGE ( 'NONE', *, *, #51992, .T. ) ; +#68742 = FILL_AREA_STYLE_COLOUR ( '', #6786 ) ; +#68744 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#68745 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#68746 = ADVANCED_FACE ( 'NONE', ( #37263 ), #29570, .T. ) ; +#68747 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#68748 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68749 = VECTOR ( 'NONE', #91231, 1000.000000000000000 ) ; +#68750 = ORIENTED_EDGE ( 'NONE', *, *, #71432, .F. ) ; +#68751 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#68752 = LINE ( 'NONE', #38640, #51044 ) ; +#68753 = ORIENTED_EDGE ( 'NONE', *, *, #60402, .F. ) ; +#68754 = VERTEX_POINT ( 'NONE', #56621 ) ; +#68755 = CARTESIAN_POINT ( 'NONE', ( 1.134147553444200041, -1.508462442331270026, 0.8299999999999999600 ) ) ; +#68756 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68757 = EDGE_CURVE ( 'NONE', #49745, #90815, #40772, .T. ) ; +#68758 = VECTOR ( 'NONE', #5011, 1000.000000000000114 ) ; +#68759 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68760 = SURFACE_STYLE_FILL_AREA ( #53975 ) ; +#68761 = EDGE_CURVE ( 'NONE', #94205, #74058, #25462, .T. ) ; +#68762 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16578 ) ) ; +#68763 = ORIENTED_EDGE ( 'NONE', *, *, #39387, .F. ) ; +#68764 = SURFACE_SIDE_STYLE ('',( #85113 ) ) ; +#68765 = ORIENTED_EDGE ( 'NONE', *, *, #89575, .T. ) ; +#68766 = EDGE_CURVE ( 'NONE', #98939, #73465, #80087, .T. ) ; +#68767 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93245 ), #62327 ) ; +#68768 = FILL_AREA_STYLE_COLOUR ( '', #35888 ) ; +#68769 = CARTESIAN_POINT ( 'NONE', ( -0.06269022549541880540, -0.9718760589866800581, 0.8299999999999999600 ) ) ; +#68770 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68771 = FACE_OUTER_BOUND ( 'NONE', #100520, .T. ) ; +#68772 = SURFACE_STYLE_USAGE ( .BOTH. , #5465 ) ; +#68773 = LINE ( 'NONE', #92272, #14209 ) ; +#68774 = PLANE ( 'NONE', #77699 ) ; +#68775 = ORIENTED_EDGE ( 'NONE', *, *, #25232, .T. ) ; +#68776 = FACE_OUTER_BOUND ( 'NONE', #18638, .T. ) ; +#68777 = PRESENTATION_STYLE_ASSIGNMENT (( #37683 ) ) ; +#68778 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#68779 = STYLED_ITEM ( 'NONE', ( #12636 ), #52061 ) ; +#68780 = FILL_AREA_STYLE_COLOUR ( '', #26875 ) ; +#68781 = CARTESIAN_POINT ( 'NONE', ( 1.841098443137489937, -1.205608583660890076, 0.8299999999999999600 ) ) ; +#68782 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57399 ), #21507 ) ; +#68783 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68784 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#68785 = FILL_AREA_STYLE_COLOUR ( '', #83265 ) ; +#68786 = EDGE_CURVE ( 'NONE', #56861, #19073, #57116, .T. ) ; +#68787 = LINE ( 'NONE', #77471, #32091 ) ; +#68788 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#68789 = AXIS2_PLACEMENT_3D ( 'NONE', #44241, #51454, #67722 ) ; +#68791 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49301 ) ) ; +#68790 = PRESENTATION_STYLE_ASSIGNMENT (( #37694 ) ) ; +#68792 = FILL_AREA_STYLE_COLOUR ( '', #20125 ) ; +#68793 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17478, 'distance_accuracy_value', 'NONE'); +#68795 = SURFACE_STYLE_USAGE ( .BOTH. , #84646 ) ; +#68796 = CARTESIAN_POINT ( 'NONE', ( -1.254419306237802179, -1.417370842016835830, 0.8099999999996805311 ) ) ; +#68797 = ADVANCED_FACE ( 'NONE', ( #79068 ), #16732, .F. ) ; +#68798 = ORIENTED_EDGE ( 'NONE', *, *, #88184, .F. ) ; +#68799 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#68800 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68801 = CARTESIAN_POINT ( 'NONE', ( 1.688590486522010048, -1.445336647901249938, 0.8299999999999977396 ) ) ; +#68802 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68803 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42413, 'distance_accuracy_value', 'NONE'); +#68804 = EDGE_CURVE ( 'NONE', #6634, #42889, #8506, .T. ) ; +#68805 = CARTESIAN_POINT ( 'NONE', ( 1.440177915673575226, -1.312528618838271210, 0.8099999999997933298 ) ) ; +#68806 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35511 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97850, #67257, #90752 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68807 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65551 ) ) ; +#68808 = STYLED_ITEM ( 'NONE', ( #18711 ), #96079 ) ; +#68809 = ORIENTED_EDGE ( 'NONE', *, *, #45134, .T. ) ; +#68810 = FILL_AREA_STYLE ('',( #59223 ) ) ; +#68811 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13952 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42030, #41531, #2726 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68812 = VECTOR ( 'NONE', #38668, 1000.000000000000000 ) ; +#68813 = FACE_OUTER_BOUND ( 'NONE', #34989, .T. ) ; +#68814 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62625, 'distance_accuracy_value', 'NONE'); +#68815 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31434 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25712, #15989, #1731 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68816 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75758, 'distance_accuracy_value', 'NONE'); +#68817 = CYLINDRICAL_SURFACE ( 'NONE', #17548, 0.009999999999999998473 ) ; +#68818 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69412 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36671, #99811, #95255 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68819 = FILL_AREA_STYLE_COLOUR ( '', #99798 ) ; +#68820 = ORIENTED_EDGE ( 'NONE', *, *, #87224, .F. ) ; +#68821 = VERTEX_POINT ( 'NONE', #78541 ) ; +#68822 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65406, #49621, #43440, #57285 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68823 = SURFACE_STYLE_FILL_AREA ( #44838 ) ; +#68824 = AXIS2_PLACEMENT_3D ( 'NONE', #27937, #41735, #65203 ) ; +#68825 = EDGE_LOOP ( 'NONE', ( #66125, #99767, #8242, #87560 ) ) ; +#68826 = PLANE ( 'NONE', #14094 ) ; +#68827 = CARTESIAN_POINT ( 'NONE', ( 6.325405999999999196, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#68828 = PRESENTATION_STYLE_ASSIGNMENT (( #55464 ) ) ; +#68829 = FILL_AREA_STYLE_COLOUR ( '', #25198 ) ; +#68830 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96778 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48135, #78757, #16955 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68831 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #18158 ) ; +#68832 = FACE_OUTER_BOUND ( 'NONE', #50699, .T. ) ; +#68833 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68835 = ORIENTED_EDGE ( 'NONE', *, *, #89200, .T. ) ; +#68834 = ORIENTED_EDGE ( 'NONE', *, *, #1706, .T. ) ; +#68836 = AXIS2_PLACEMENT_3D ( 'NONE', #88371, #58276, #72538 ) ; +#68837 = VERTEX_POINT ( 'NONE', #39751 ) ; +#68838 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666647068, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#68839 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#68840 = ORIENTED_EDGE ( 'NONE', *, *, #96170, .T. ) ; +#68841 = VECTOR ( 'NONE', #95067, 1000.000000000000000 ) ; +#68842 = VERTEX_POINT ( 'NONE', #24966 ) ; +#68843 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#68844 = EDGE_CURVE ( 'NONE', #34886, #39774, #18398, .T. ) ; +#68845 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90089 ) ) ; +#68846 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01499999999999995781, -0.1458578643762691029 ) ) ; +#68847 = STYLED_ITEM ( 'NONE', ( #91313 ), #52181 ) ; +#68849 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68848 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#68850 = ORIENTED_EDGE ( 'NONE', *, *, #48863, .F. ) ; +#68851 = CARTESIAN_POINT ( 'NONE', ( -0.4757128391191070560, -0.9978229697136190568, 0.8100000000000000533 ) ) ; +#68852 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34667 ) ) ; +#68853 = ORIENTED_EDGE ( 'NONE', *, *, #83171, .F. ) ; +#68854 = ORIENTED_EDGE ( 'NONE', *, *, #66946, .F. ) ; +#68855 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#68856 = PRESENTATION_STYLE_ASSIGNMENT (( #52583 ) ) ; +#68857 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68858 = VECTOR ( 'NONE', #5327, 1000.000000000000000 ) ; +#68860 = ORIENTED_EDGE ( 'NONE', *, *, #57309, .T. ) ; +#68859 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99201, 'distance_accuracy_value', 'NONE'); +#68861 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68862 = SURFACE_SIDE_STYLE ('',( #44879 ) ) ; +#68863 = PLANE ( 'NONE', #83149 ) ; +#68864 = ORIENTED_EDGE ( 'NONE', *, *, #7084, .T. ) ; +#68865 = CARTESIAN_POINT ( 'NONE', ( -0.004761740495047140850, -1.264112177694660000, 0.8100000000000000533 ) ) ; +#68866 = FILL_AREA_STYLE ('',( #93346 ) ) ; +#68867 = ORIENTED_EDGE ( 'NONE', *, *, #52346, .T. ) ; +#68868 = VERTEX_POINT ( 'NONE', #55606 ) ; +#68869 = SURFACE_STYLE_USAGE ( .BOTH. , #22961 ) ; +#68870 = FILL_AREA_STYLE_COLOUR ( '', #79143 ) ; +#68871 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68872 = STYLED_ITEM ( 'NONE', ( #30034 ), #37425 ) ; +#68873 = AXIS2_PLACEMENT_3D ( 'NONE', #14884, #22088, #54252 ) ; +#68874 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990585, 0.000000000000000000 ) ) ; +#68875 = CIRCLE ( 'NONE', #47698, 0.09999999999999982514 ) ; +#68876 = STYLED_ITEM ( 'NONE', ( #69524 ), #87133 ) ; +#68877 = AXIS2_PLACEMENT_3D ( 'NONE', #96062, #34345, #88948 ) ; +#68878 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.000000000000000000 ) ) ; +#68879 = CARTESIAN_POINT ( 'NONE', ( 1.137573705260860102, -1.210702855844099979, 0.8299999999999997380 ) ) ; +#68880 = VECTOR ( 'NONE', #94035, 1000.000000000000114 ) ; +#68881 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000002554, -3.266666666666653285, 0.000000000000000000 ) ) ; +#68882 = VERTEX_POINT ( 'NONE', #56099 ) ; +#68883 = FILL_AREA_STYLE ('',( #22971 ) ) ; +#68884 = SURFACE_SIDE_STYLE ('',( #9066 ) ) ; +#68885 = VERTEX_POINT ( 'NONE', #17253 ) ; +#68886 = EDGE_CURVE ( 'NONE', #64323, #59761, #35141, .T. ) ; +#68887 = VECTOR ( 'NONE', #70002, 1000.000000000000000 ) ; +#68888 = SURFACE_STYLE_FILL_AREA ( #53112 ) ; +#68890 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79960, 'distance_accuracy_value', 'NONE'); +#68889 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#68891 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000006176, -0.2400000000000000189 ) ) ; +#68892 = AXIS2_PLACEMENT_3D ( 'NONE', #56110, #17760, #57640 ) ; +#68893 = PLANE ( 'NONE', #1334 ) ; +#68895 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68894 = LINE ( 'NONE', #53615, #26717 ) ; +#68896 = CARTESIAN_POINT ( 'NONE', ( 1.795940028366769914, -1.028719707420159946, 0.8100000000000000533 ) ) ; +#68897 = PLANE ( 'NONE', #73951 ) ; +#68898 = LINE ( 'NONE', #98970, #83509 ) ; +#68899 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#68900 = VECTOR ( 'NONE', #95064, 1000.000000000000000 ) ; +#68901 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68902 = EDGE_CURVE ( 'NONE', #20127, #63293, #43262, .T. ) ; +#68903 = PRESENTATION_STYLE_ASSIGNMENT (( #8563 ) ) ; +#68904 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46083 ), #57618 ) ; +#68905 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30627 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19375, #58228, #59233 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68906 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89554, 'distance_accuracy_value', 'NONE'); +#68907 = EDGE_LOOP ( 'NONE', ( #20019, #22823, #85054, #100874, #18985, #69780 ) ) ; +#68908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68909 = EDGE_CURVE ( 'NONE', #34605, #64233, #20274, .T. ) ; +#68910 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68911 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68912 = PRESENTATION_STYLE_ASSIGNMENT (( #69417 ) ) ; +#68913 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#68914 = PLANE ( 'NONE', #97148 ) ; +#68915 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51057 ), #45873 ) ; +#68916 = DIRECTION ( 'NONE', ( -0.8186165608382627301, -0.5743404272044019265, 0.000000000000000000 ) ) ; +#68917 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68918 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#68919 = AXIS2_PLACEMENT_3D ( 'NONE', #33512, #10402, #57507 ) ; +#68920 = LINE ( 'NONE', #55053, #99032 ) ; +#68921 = VERTEX_POINT ( 'NONE', #42773 ) ; +#68922 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68923 = VECTOR ( 'NONE', #93596, 1000.000000000000000 ) ; +#68924 = EDGE_LOOP ( 'NONE', ( #24494, #62944, #920, #26690 ) ) ; +#68925 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691085, -0.01085786437626905590, -0.2500000000000000000 ) ) ; +#68926 = EDGE_CURVE ( 'NONE', #8017, #18378, #51466, .T. ) ; +#68927 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68928 = PRESENTATION_STYLE_ASSIGNMENT (( #6608 ) ) ; +#68929 = CARTESIAN_POINT ( 'NONE', ( -0.2361504354203300127, -1.354501511147599979, 0.8299999999999995159 ) ) ; +#68930 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68931 = VECTOR ( 'NONE', #63060, 1000.000000000000000 ) ; +#68932 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11808 ) ) ; +#68933 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#68934 = PRESENTATION_STYLE_ASSIGNMENT (( #60836 ) ) ; +#68935 = EDGE_CURVE ( 'NONE', #89973, #90126, #3767, .T. ) ; +#68936 = ORIENTED_EDGE ( 'NONE', *, *, #66268, .F. ) ; +#68937 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89762 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49279, #65584, #40615 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68938 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, -13.54999999999999893 ) ) ; +#68939 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68940 = ORIENTED_EDGE ( 'NONE', *, *, #25668, .T. ) ; +#68941 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33130 ) ) ; +#68942 = ORIENTED_EDGE ( 'NONE', *, *, #20595, .F. ) ; +#68943 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#68944 = EDGE_CURVE ( 'NONE', #25071, #26712, #97361, .T. ) ; +#68945 = ADVANCED_FACE ( 'NONE', ( #4456 ), #13049, .T. ) ; +#68946 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#68947 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#68948 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#68949 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68950 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#68951 = CARTESIAN_POINT ( 'NONE', ( 0.005924814402238407114, 1.124625895891711025, 0.8099999999999999423 ) ) ; +#68953 = ORIENTED_EDGE ( 'NONE', *, *, #31175, .F. ) ; +#68952 = EDGE_LOOP ( 'NONE', ( #11557, #32972, #43895, #29058 ) ) ; +#68955 = EDGE_CURVE ( 'NONE', #85813, #6033, #49956, .T. ) ; +#68954 = SURFACE_SIDE_STYLE ('',( #44973 ) ) ; +#68956 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96727 ) ) ; +#68957 = EDGE_CURVE ( 'NONE', #25544, #1291, #66260, .T. ) ; +#68958 = SURFACE_STYLE_FILL_AREA ( #30662 ) ; +#68959 = EDGE_LOOP ( 'NONE', ( #87746, #83294, #75649, #99769, #90428, #7522 ) ) ; +#68960 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#68961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44479 ), #65733 ) ; +#68963 = CARTESIAN_POINT ( 'NONE', ( -0.4444315888559909888, -1.066522886050349950, 0.8100000000000000533 ) ) ; +#68962 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68964 = ORIENTED_EDGE ( 'NONE', *, *, #36860, .T. ) ; +#68965 = ORIENTED_EDGE ( 'NONE', *, *, #64379, .F. ) ; +#68966 = LINE ( 'NONE', #77155, #44874 ) ; +#68967 = ADVANCED_FACE ( 'NONE', ( #27465 ), #4938, .T. ) ; +#68968 = SURFACE_STYLE_USAGE ( .BOTH. , #45977 ) ; +#68969 = VECTOR ( 'NONE', #35603, 999.9999999999998863 ) ; +#68971 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, 0.2250000000000000333 ) ) ; +#68970 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#68972 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 7.848067000000000348, 0.8648700000000000276 ) ) ; +#68973 = ORIENTED_EDGE ( 'NONE', *, *, #62605, .T. ) ; +#68974 = EDGE_LOOP ( 'NONE', ( #32174, #2471, #38371, #70989 ) ) ; +#68975 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75746, #74757, #83914, #29774 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#68976 = PRESENTATION_STYLE_ASSIGNMENT (( #6645 ) ) ; +#68977 = ORIENTED_EDGE ( 'NONE', *, *, #17944, .T. ) ; +#68978 = ADVANCED_FACE ( 'NONE', ( #15084 ), #53450, .T. ) ; +#68980 = ORIENTED_EDGE ( 'NONE', *, *, #39802, .T. ) ; +#68979 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#68981 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#68982 = FILL_AREA_STYLE_COLOUR ( '', #97001 ) ; +#68983 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#68984 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46979 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12399, #75280, #74779 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68985 = VERTEX_POINT ( 'NONE', #30958 ) ; +#68986 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#68987 = VERTEX_POINT ( 'NONE', #14589 ) ; +#68988 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#68989 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#68990 = VECTOR ( 'NONE', #94121, 1000.000000000000000 ) ; +#68991 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21206 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24696, #2194, #47126 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#68992 = ORIENTED_EDGE ( 'NONE', *, *, #33261, .F. ) ; +#68993 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#68995 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#68994 = PRESENTATION_STYLE_ASSIGNMENT (( #30204 ) ) ; +#68996 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.000000000000000000, -0.2400000000000000189 ) ) ; +#68997 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11879 ) ) ; +#68998 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#68999 = VERTEX_POINT ( 'NONE', #45730 ) ; +#69000 = EDGE_CURVE ( 'NONE', #24110, #5293, #76920, .T. ) ; +#69001 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69002 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69003 = VECTOR ( 'NONE', #49239, 1000.000000000000000 ) ; +#69004 = AXIS2_PLACEMENT_3D ( 'NONE', #80413, #67557, #73263 ) ; +#69005 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69006 = EDGE_CURVE ( 'NONE', #74547, #19627, #21285, .T. ) ; +#69008 = CARTESIAN_POINT ( 'NONE', ( 1.316988700902881337, -1.421953058340963638, 0.8099999999997246070 ) ) ; +#69007 = FACE_OUTER_BOUND ( 'NONE', #89132, .T. ) ; +#69009 = LINE ( 'NONE', #22579, #43794 ) ; +#69010 = SURFACE_STYLE_FILL_AREA ( #62926 ) ; +#69011 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69012 = AXIS2_PLACEMENT_3D ( 'NONE', #72327, #874, #9956 ) ; +#69013 = FILL_AREA_STYLE_COLOUR ( '', #54200 ) ; +#69014 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69015 = EDGE_LOOP ( 'NONE', ( #63011, #80209, #18250, #51681 ) ) ; +#69017 = VECTOR ( 'NONE', #46850, 1000.000000000000000 ) ; +#69016 = SURFACE_STYLE_USAGE ( .BOTH. , #99098 ) ; +#69018 = VECTOR ( 'NONE', #90322, 1000.000000000000000 ) ; +#69019 = EDGE_LOOP ( 'NONE', ( #70388, #9707, #26865, #67219 ) ) ; +#69020 = SURFACE_SIDE_STYLE ('',( #20071 ) ) ; +#69021 = LINE ( 'NONE', #60432, #78419 ) ; +#69023 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11903 ) ) ; +#69022 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#69024 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#69025 = AXIS2_PLACEMENT_3D ( 'NONE', #85085, #70265, #7397 ) ; +#69026 = EDGE_LOOP ( 'NONE', ( #32629, #3687, #60332, #76481 ) ) ; +#69027 = FILL_AREA_STYLE ('',( #94006 ) ) ; +#69028 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69029 = SURFACE_SIDE_STYLE ('',( #59948 ) ) ; +#69030 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21767 ), #47875 ) ; +#69031 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8648700000000000276 ) ) ; +#69032 = SURFACE_STYLE_FILL_AREA ( #92043 ) ; +#69033 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#69034 = VERTEX_POINT ( 'NONE', #62139 ) ; +#69035 = CARTESIAN_POINT ( 'NONE', ( 6.954730750249974669, 2.311420750249975953, 0.8648700000000000276 ) ) ; +#69036 = AXIS2_PLACEMENT_3D ( 'NONE', #54227, #30709, #82 ) ; +#69037 = ORIENTED_EDGE ( 'NONE', *, *, #6636, .F. ) ; +#69038 = PRESENTATION_STYLE_ASSIGNMENT (( #5752 ) ) ; +#69039 = CARTESIAN_POINT ( 'NONE', ( 1.101360327800479988, -0.9762538161110779766, 0.8299999999999999600 ) ) ; +#69040 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#69041 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69042 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69043 = DIRECTION ( 'NONE', ( -0.7071060119555133694, 0.7071075504167448900, 0.000000000000000000 ) ) ; +#69044 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#69045 = STYLED_ITEM ( 'NONE', ( #12790 ), #53369 ) ; +#69046 = SURFACE_SIDE_STYLE ('',( #92542 ) ) ; +#69047 = ORIENTED_EDGE ( 'NONE', *, *, #13306, .T. ) ; +#69048 = FACE_OUTER_BOUND ( 'NONE', #56738, .T. ) ; +#69049 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69050 = PRESENTATION_STYLE_ASSIGNMENT (( #62471 ) ) ; +#69051 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69052 = ORIENTED_EDGE ( 'NONE', *, *, #21368, .F. ) ; +#69053 = SURFACE_STYLE_FILL_AREA ( #8243 ) ; +#69054 = STYLED_ITEM ( 'NONE', ( #27812 ), #47660 ) ; +#69055 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#69056 = VECTOR ( 'NONE', #21567, 1000.000000000000000 ) ; +#69057 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69058 = ORIENTED_EDGE ( 'NONE', *, *, #55115, .F. ) ; +#69059 = EDGE_CURVE ( 'NONE', #90220, #35538, #77412, .T. ) ; +#69060 = LINE ( 'NONE', #61485, #42672 ) ; +#69061 = AXIS2_PLACEMENT_3D ( 'NONE', #25524, #11601, #72976 ) ; +#69062 = ORIENTED_EDGE ( 'NONE', *, *, #81963, .T. ) ; +#69064 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69063 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69065 = SURFACE_STYLE_USAGE ( .BOTH. , #78787 ) ; +#69066 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#69067 = ORIENTED_EDGE ( 'NONE', *, *, #48140, .T. ) ; +#69068 = SURFACE_STYLE_USAGE ( .BOTH. , #77272 ) ; +#69069 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54503 ), #98413 ) ; +#69070 = VERTEX_POINT ( 'NONE', #93196 ) ; +#69071 = EDGE_CURVE ( 'NONE', #11607, #70921, #99311, .T. ) ; +#69072 = STYLED_ITEM ( 'NONE', ( #49283 ), #97095 ) ; +#69073 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79870, 'distance_accuracy_value', 'NONE'); +#69074 = VECTOR ( 'NONE', #37743, 1000.000000000000000 ) ; +#69075 = ORIENTED_EDGE ( 'NONE', *, *, #56170, .T. ) ; +#69076 = ORIENTED_EDGE ( 'NONE', *, *, #27749, .F. ) ; +#69077 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38147, 'distance_accuracy_value', 'NONE'); +#69078 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88675 ) ) ; +#69080 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#69079 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#69081 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69082 = LINE ( 'NONE', #22167, #61808 ) ; +#69083 = ORIENTED_EDGE ( 'NONE', *, *, #85353, .F. ) ; +#69084 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69085 = LINE ( 'NONE', #29818, #21487 ) ; +#69086 = VERTEX_POINT ( 'NONE', #85577 ) ; +#69087 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#69088 = SURFACE_SIDE_STYLE ('',( #47165 ) ) ; +#69089 = FILL_AREA_STYLE_COLOUR ( '', #5695 ) ; +#69090 = LINE ( 'NONE', #100170, #14010 ) ; +#69091 = STYLED_ITEM ( 'NONE', ( #32205 ), #67781 ) ; +#69092 = ORIENTED_EDGE ( 'NONE', *, *, #20884, .T. ) ; +#69093 = LINE ( 'NONE', #90631, #69801 ) ; +#69094 = EDGE_LOOP ( 'NONE', ( #67862, #42022, #46382, #48148, #74181 ) ) ; +#69095 = EDGE_CURVE ( 'NONE', #12703, #78529, #77924, .T. ) ; +#69097 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#69096 = PLANE ( 'NONE', #64258 ) ; +#69098 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#69099 = STYLED_ITEM ( 'NONE', ( #52995 ), #71414 ) ; +#69100 = FACE_OUTER_BOUND ( 'NONE', #83486, .T. ) ; +#69101 = ORIENTED_EDGE ( 'NONE', *, *, #1856, .F. ) ; +#69102 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69103 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61020 ) ) ; +#69104 = ORIENTED_EDGE ( 'NONE', *, *, #70264, .T. ) ; +#69105 = EDGE_CURVE ( 'NONE', #51626, #48017, #40315, .T. ) ; +#69106 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69107 = LINE ( 'NONE', #13985, #37115 ) ; +#69108 = AXIS2_PLACEMENT_3D ( 'NONE', #16783, #63808, #56154 ) ; +#69109 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#69110 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#69112 = STYLED_ITEM ( 'NONE', ( #56703 ), #48160 ) ; +#69111 = PLANE ( 'NONE', #34904 ) ; +#69113 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69114 = SURFACE_SIDE_STYLE ('',( #38531 ) ) ; +#69115 = LINE ( 'NONE', #13459, #36467 ) ; +#69116 = PRESENTATION_STYLE_ASSIGNMENT (( #23228 ) ) ; +#69117 = LINE ( 'NONE', #6792, #84579 ) ; +#69118 = ORIENTED_EDGE ( 'NONE', *, *, #37757, .T. ) ; +#69119 = VECTOR ( 'NONE', #98236, 999.9999999999998863 ) ; +#69120 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69122 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#69121 = SURFACE_STYLE_FILL_AREA ( #76833 ) ; +#69123 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20847, 'distance_accuracy_value', 'NONE'); +#69124 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69125 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69126 = AXIS2_PLACEMENT_3D ( 'NONE', #51360, #67630, #74325 ) ; +#69127 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71434 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62202, #70322, #92767 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69128 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#69129 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#69130 = VECTOR ( 'NONE', #38445, 1000.000000000000000 ) ; +#69131 = LINE ( 'NONE', #100206, #54321 ) ; +#69132 = VERTEX_POINT ( 'NONE', #39123 ) ; +#69133 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69134 = ADVANCED_FACE ( 'NONE', ( #44745 ), #75915, .T. ) ; +#69135 = LINE ( 'NONE', #38550, #99849 ) ; +#69137 = AXIS2_PLACEMENT_3D ( 'NONE', #24260, #84989, #16040 ) ; +#69136 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3597, #96983, #75913 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69138 = CARTESIAN_POINT ( 'NONE', ( -0.01471107728978500104, -1.407725713391660083, 0.8100000000000000533 ) ) ; +#69139 = AXIS2_PLACEMENT_3D ( 'NONE', #38185, #53010, #92284 ) ; +#69140 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#69141 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69142 = PRESENTATION_STYLE_ASSIGNMENT (( #86535 ) ) ; +#69144 = SURFACE_STYLE_FILL_AREA ( #93134 ) ; +#69143 = AXIS2_PLACEMENT_3D ( 'NONE', #97151, #60302, #73218 ) ; +#69145 = EDGE_CURVE ( 'NONE', #82715, #19945, #32982, .T. ) ; +#69146 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#69147 = SURFACE_SIDE_STYLE ('',( #6347 ) ) ; +#69148 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69149 = SURFACE_STYLE_FILL_AREA ( #52900 ) ; +#69150 = DIRECTION ( 'NONE', ( 0.7071067811865472397, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#69151 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69152 = SURFACE_STYLE_FILL_AREA ( #20730 ) ; +#69153 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69154 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999992895, 0.1829999999999790405 ) ) ; +#69155 = VECTOR ( 'NONE', #67241, 1000.000000000000000 ) ; +#69156 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69157 = SURFACE_SIDE_STYLE ('',( #67191 ) ) ; +#69158 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#69159 = VECTOR ( 'NONE', #90503, 1000.000000000000000 ) ; +#69160 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.000000000000000000 ) ) ; +#69161 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69162 = CYLINDRICAL_SURFACE ( 'NONE', #20639, 0.009999999999999998473 ) ; +#69163 = AXIS2_PLACEMENT_3D ( 'NONE', #43889, #34759, #36252 ) ; +#69164 = LINE ( 'NONE', #1280, #22703 ) ; +#69165 = CARTESIAN_POINT ( 'NONE', ( 10.10135575024997223, 8.852158750249975228, 0.8648700000000000276 ) ) ; +#69166 = VERTEX_POINT ( 'NONE', #25844 ) ; +#69167 = FACE_OUTER_BOUND ( 'NONE', #89336, .T. ) ; +#69168 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.383333333333333304, 1.747825839084932944E-76 ) ) ; +#69169 = AXIS2_PLACEMENT_3D ( 'NONE', #92332, #1307, #68346 ) ; +#69170 = PRESENTATION_STYLE_ASSIGNMENT (( #86045 ) ) ; +#69171 = ORIENTED_EDGE ( 'NONE', *, *, #45020, .F. ) ; +#69172 = SURFACE_SIDE_STYLE ('',( #39090 ) ) ; +#69173 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85542 ), #72495 ) ; +#69174 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69175 = SURFACE_SIDE_STYLE ('',( #22767 ) ) ; +#69176 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69177 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69178 = VERTEX_POINT ( 'NONE', #24850 ) ; +#69179 = FILL_AREA_STYLE ('',( #38101 ) ) ; +#69180 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#69181 = EDGE_CURVE ( 'NONE', #26599, #39738, #18121, .T. ) ; +#69182 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2620, 'distance_accuracy_value', 'NONE'); +#69183 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50953 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3634, #18931, #97529 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69184 = ORIENTED_EDGE ( 'NONE', *, *, #87636, .F. ) ; +#69185 = ORIENTED_EDGE ( 'NONE', *, *, #97370, .T. ) ; +#69186 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57851 ) ) ; +#69187 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#69188 = ORIENTED_EDGE ( 'NONE', *, *, #60116, .T. ) ; +#69189 = FILL_AREA_STYLE_COLOUR ( '', #64032 ) ; +#69190 = CARTESIAN_POINT ( 'NONE', ( 0.06855147566562069805, -1.423344911062679907, 0.8100000000000000533 ) ) ; +#69191 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69192 = FACE_OUTER_BOUND ( 'NONE', #47665, .T. ) ; +#69193 = EDGE_CURVE ( 'NONE', #15372, #52597, #41157, .T. ) ; +#69194 = ORIENTED_EDGE ( 'NONE', *, *, #49126, .T. ) ; +#69195 = ORIENTED_EDGE ( 'NONE', *, *, #78912, .T. ) ; +#69196 = SURFACE_SIDE_STYLE ('',( #16472 ) ) ; +#69197 = VECTOR ( 'NONE', #41330, 1000.000000000000000 ) ; +#69199 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57152 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74370, #35586, #97784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69198 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38169, 'distance_accuracy_value', 'NONE'); +#69200 = VECTOR ( 'NONE', #53144, 1000.000000000000000 ) ; +#69201 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000003147, 0.4000000000000000222 ) ) ; +#69202 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#69204 = STYLED_ITEM ( 'NONE', ( #7527 ), #27172 ) ; +#69203 = STYLED_ITEM ( 'NONE', ( #13956 ), #38470 ) ; +#69205 = VECTOR ( 'NONE', #356, 1000.000000000000000 ) ; +#69206 = SURFACE_STYLE_FILL_AREA ( #45731 ) ; +#69207 = ORIENTED_EDGE ( 'NONE', *, *, #78880, .T. ) ; +#69208 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69209 = VERTEX_POINT ( 'NONE', #79458 ) ; +#69210 = ORIENTED_EDGE ( 'NONE', *, *, #86763, .F. ) ; +#69211 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46430 ) ) ; +#69212 = ADVANCED_FACE ( 'NONE', ( #9416 ), #16608, .F. ) ; +#69214 = FILL_AREA_STYLE ('',( #43770 ) ) ; +#69213 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333313320, -2.500000000000000000, 0.000000000000000000 ) ) ; +#69215 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#69216 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69218 = EDGE_LOOP ( 'NONE', ( #52947, #77559, #1859, #53298 ) ) ; +#69217 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#69219 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12129 ) ) ; +#69220 = SURFACE_STYLE_USAGE ( .BOTH. , #38149 ) ; +#69221 = VECTOR ( 'NONE', #31736, 1000.000000000000000 ) ; +#69222 = PRESENTATION_STYLE_ASSIGNMENT (( #76942 ) ) ; +#69223 = VERTEX_POINT ( 'NONE', #71789 ) ; +#69224 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69225 = VERTEX_POINT ( 'NONE', #8387 ) ; +#69226 = ORIENTED_EDGE ( 'NONE', *, *, #35372, .T. ) ; +#69227 = SURFACE_STYLE_FILL_AREA ( #32515 ) ; +#69228 = EDGE_CURVE ( 'NONE', #58651, #97931, #93697, .T. ) ; +#69230 = PRESENTATION_STYLE_ASSIGNMENT (( #85603 ) ) ; +#69229 = CARTESIAN_POINT ( 'NONE', ( 1.198411601801520066, -1.515412412365080064, 0.8299999999999999600 ) ) ; +#69231 = FILL_AREA_STYLE_COLOUR ( '', #94566 ) ; +#69232 = LINE ( 'NONE', #84609, #8900 ) ; +#69233 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82357 ), #38326 ) ; +#69234 = FILL_AREA_STYLE ('',( #63170 ) ) ; +#69235 = SURFACE_STYLE_USAGE ( .BOTH. , #76958 ) ; +#69236 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25311 ), #100149 ) ; +#69237 = SURFACE_STYLE_USAGE ( .BOTH. , #77441 ) ; +#69238 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#69239 = FILL_AREA_STYLE_COLOUR ( '', #50489 ) ; +#69240 = ORIENTED_EDGE ( 'NONE', *, *, #99676, .T. ) ; +#69241 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69242 = ORIENTED_EDGE ( 'NONE', *, *, #88130, .T. ) ; +#69243 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#69244 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#69245 = CARTESIAN_POINT ( 'NONE', ( 1.148671667572580102, -1.140452398731560013, 0.8100000000000000533 ) ) ; +#69246 = PRESENTATION_STYLE_ASSIGNMENT (( #14629 ) ) ; +#69248 = SURFACE_SIDE_STYLE ('',( #7436 ) ) ; +#69247 = CIRCLE ( 'NONE', #98513, 0.2000000000000000111 ) ; +#69249 = STYLED_ITEM ( 'NONE', ( #3005 ), #54011 ) ; +#69250 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69251 = PLANE ( 'NONE', #77813 ) ; +#69252 = FILL_AREA_STYLE ('',( #74972 ) ) ; +#69253 = PRESENTATION_STYLE_ASSIGNMENT (( #92274 ) ) ; +#69254 = EDGE_LOOP ( 'NONE', ( #76793, #5426, #7408, #21885 ) ) ; +#69255 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38346 ) ) ; +#69256 = VECTOR ( 'NONE', #31586, 1000.000000000000000 ) ; +#69258 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#69257 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69259 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#69260 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#69261 = FILL_AREA_STYLE_COLOUR ( '', #88180 ) ; +#69262 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35171 ), #10542 ) ; +#69263 = AXIS2_PLACEMENT_3D ( 'NONE', #88690, #90197, #35108 ) ; +#69264 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43227 ), #2498 ) ; +#69265 = CARTESIAN_POINT ( 'NONE', ( 1.830402071067120051, -1.199770973383029959, 0.8100000000000000533 ) ) ; +#69266 = EDGE_CURVE ( 'NONE', #74573, #59388, #94227, .T. ) ; +#69267 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999940048, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#69268 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8648700000000000276 ) ) ; +#69270 = FILL_AREA_STYLE ('',( #22346 ) ) ; +#69269 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90458 ), #4098 ) ; +#69271 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69272 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, 0.1200000000000003147, 0.3499999999999999778 ) ) ; +#69273 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#69274 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69275 = CARTESIAN_POINT ( 'NONE', ( 1.314833503436970030, -1.000241703689469963, 0.8299999999999995159 ) ) ; +#69276 = VECTOR ( 'NONE', #69559, 1000.000000000000000 ) ; +#69277 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38369 ), #82399 ) ; +#69278 = FILL_AREA_STYLE_COLOUR ( '', #63415 ) ; +#69279 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.09999999999999870104, 6.355796620655076481E-79 ) ) ; +#69280 = EDGE_CURVE ( 'NONE', #82518, #33509, #78931, .T. ) ; +#69281 = VERTEX_POINT ( 'NONE', #1328 ) ; +#69282 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69283 = PLANE ( 'NONE', #62769 ) ; +#69284 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69285 = EDGE_CURVE ( 'NONE', #55937, #47557, #32486, .T. ) ; +#69286 = VECTOR ( 'NONE', #72300, 1000.000000000000000 ) ; +#69287 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69288 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69289 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#69290 = EDGE_CURVE ( 'NONE', #777, #43767, #26266, .T. ) ; +#69291 = DIRECTION ( 'NONE', ( 0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#69292 = CARTESIAN_POINT ( 'NONE', ( 1.275468060740723386, -1.170256537188258950, 0.8099999999998828137 ) ) ; +#69293 = FILL_AREA_STYLE_COLOUR ( '', #32030 ) ; +#69294 = EDGE_LOOP ( 'NONE', ( #99999, #89506, #37270, #52437 ) ) ; +#69295 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12205 ) ) ; +#69296 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69297 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#69299 = EDGE_CURVE ( 'NONE', #77944, #6871, #96246, .T. ) ; +#69298 = AXIS2_PLACEMENT_3D ( 'NONE', #59494, #37971, #90589 ) ; +#69300 = SURFACE_STYLE_FILL_AREA ( #6970 ) ; +#69301 = PRESENTATION_STYLE_ASSIGNMENT (( #1433 ) ) ; +#69302 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000053513, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#69303 = EDGE_LOOP ( 'NONE', ( #61239, #75169, #48956, #85211 ) ) ; +#69304 = EDGE_CURVE ( 'NONE', #100016, #99445, #97247, .T. ) ; +#69305 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66276, #88744, #11045, #96874 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#69306 = EDGE_LOOP ( 'NONE', ( #85466, #19538, #73561, #3798 ) ) ; +#69307 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39993 ) ) ; +#69308 = CARTESIAN_POINT ( 'NONE', ( 1.323820061220085220, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#69309 = ORIENTED_EDGE ( 'NONE', *, *, #23123, .T. ) ; +#69310 = AXIS2_PLACEMENT_3D ( 'NONE', #10046, #64272, #55128 ) ; +#69311 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69312 = SURFACE_STYLE_FILL_AREA ( #62733 ) ; +#69313 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 0.5862888163215710380 ) ) ; +#69314 = SURFACE_SIDE_STYLE ('',( #21389 ) ) ; +#69315 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#69316 = EDGE_CURVE ( 'NONE', #66135, #5169, #83345, .T. ) ; +#69317 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #7062 ) ; +#69318 = LINE ( 'NONE', #62237, #54117 ) ; +#69319 = EDGE_CURVE ( 'NONE', #2963, #19573, #26344, .T. ) ; +#69321 = ORIENTED_EDGE ( 'NONE', *, *, #46925, .F. ) ; +#69320 = ORIENTED_EDGE ( 'NONE', *, *, #45020, .T. ) ; +#69322 = ORIENTED_EDGE ( 'NONE', *, *, #10782, .T. ) ; +#69323 = FILL_AREA_STYLE_COLOUR ( '', #97977 ) ; +#69324 = EDGE_CURVE ( 'NONE', #63500, #92532, #13822, .T. ) ; +#69325 = VECTOR ( 'NONE', #2988, 1000.000000000000000 ) ; +#69326 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85876, 'distance_accuracy_value', 'NONE'); +#69327 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, 0.000000000000000000 ) ) ; +#69328 = LINE ( 'NONE', #12680, #62675 ) ; +#69329 = VERTEX_POINT ( 'NONE', #60392 ) ; +#69330 = PRODUCT_DEFINITION ( 'δ֪', '', #4620, #22882 ) ; +#69332 = VERTEX_POINT ( 'NONE', #68498 ) ; +#69331 = VECTOR ( 'NONE', #12912, 1000.000000000000000 ) ; +#69333 = FILL_AREA_STYLE_COLOUR ( '', #79241 ) ; +#69334 = FACE_OUTER_BOUND ( 'NONE', #74077, .T. ) ; +#69335 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80859 ), #79161 ) ; +#69336 = VECTOR ( 'NONE', #62949, 1000.000000000000000 ) ; +#69337 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#69339 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69338 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.149999999999990585, 0.000000000000000000 ) ) ; +#69340 = CARTESIAN_POINT ( 'NONE', ( -0.4385307926823460711, -0.9262267064097939873, 0.8299999999999999600 ) ) ; +#69341 = ORIENTED_EDGE ( 'NONE', *, *, #36463, .T. ) ; +#69342 = AXIS2_PLACEMENT_3D ( 'NONE', #92362, #92828, #99921 ) ; +#69343 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82456 ) ) ; +#69344 = VECTOR ( 'NONE', #79152, 1000.000000000000000 ) ; +#69345 = SURFACE_STYLE_FILL_AREA ( #15211 ) ; +#69346 = ORIENTED_EDGE ( 'NONE', *, *, #28481, .T. ) ; +#69347 = ORIENTED_EDGE ( 'NONE', *, *, #90722, .T. ) ; +#69348 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#69349 = ADVANCED_FACE ( 'NONE', ( #81492 ), #84340, .T. ) ; +#69350 = FILL_AREA_STYLE_COLOUR ( '', #51027 ) ; +#69351 = PLANE ( 'NONE', #68461 ) ; +#69352 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8991599999999999593 ) ) ; +#69354 = ORIENTED_EDGE ( 'NONE', *, *, #36394, .F. ) ; +#69353 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#69355 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69356 = FILL_AREA_STYLE ('',( #54614 ) ) ; +#69357 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, 1.129999999999999893 ) ) ; +#69358 = ORIENTED_EDGE ( 'NONE', *, *, #8172, .F. ) ; +#69361 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#69360 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69359 = LINE ( 'NONE', #100416, #98661 ) ; +#69362 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69363 = ORIENTED_EDGE ( 'NONE', *, *, #13034, .F. ) ; +#69364 = ORIENTED_EDGE ( 'NONE', *, *, #91623, .T. ) ; +#69365 = ADVANCED_FACE ( 'NONE', ( #50357 ), #52700, .T. ) ; +#69366 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#69367 = FACE_OUTER_BOUND ( 'NONE', #74036, .T. ) ; +#69368 = STYLED_ITEM ( 'NONE', ( #30747 ), #99214 ) ; +#69369 = CARTESIAN_POINT ( 'NONE', ( -0.3839949111172690221, -1.170868642971409912, 0.8100000000000000533 ) ) ; +#69370 = EDGE_CURVE ( 'NONE', #63754, #28835, #100041, .T. ) ; +#69371 = FILL_AREA_STYLE ('',( #77571 ) ) ; +#69372 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87346 ) ) ; +#69373 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69374 = CARTESIAN_POINT ( 'NONE', ( 1.274810379711009967, -1.243129529655299992, 0.8299999999999997380 ) ) ; +#69376 = SURFACE_SIDE_STYLE ('',( #61289 ) ) ; +#69375 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100325, 'distance_accuracy_value', 'NONE'); +#69377 = CIRCLE ( 'NONE', #25429, 0.4459546481032609644 ) ; +#69378 = ORIENTED_EDGE ( 'NONE', *, *, #68115, .T. ) ; +#69379 = FILL_AREA_STYLE_COLOUR ( '', #73473 ) ; +#69380 = CARTESIAN_POINT ( 'NONE', ( 0.09337595685179390925, -1.316888414733939916, 0.8100000000000000533 ) ) ; +#69381 = EDGE_LOOP ( 'NONE', ( #11513, #83465, #8412, #60104 ) ) ; +#69382 = EDGE_CURVE ( 'NONE', #84782, #15411, #30690, .T. ) ; +#69383 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100344 ), #988 ) ; +#69384 = PRESENTATION_STYLE_ASSIGNMENT (( #61295 ) ) ; +#69385 = FILL_AREA_STYLE ('',( #85237 ) ) ; +#69387 = VECTOR ( 'NONE', #15182, 1000.000000000000000 ) ; +#69386 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69388 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69389 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#69390 = CARTESIAN_POINT ( 'NONE', ( 1.698015391961940068, -0.9623926821384259922, 0.8299999999999999600 ) ) ; +#69391 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#69392 = FILL_AREA_STYLE_COLOUR ( '', #80951 ) ; +#69393 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69394 = PRESENTATION_STYLE_ASSIGNMENT (( #62292 ) ) ; +#69395 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#69396 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#69397 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#69398 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77597 ) ) ; +#69399 = LINE ( 'NONE', #99960, #82516 ) ; +#69400 = EDGE_CURVE ( 'NONE', #97964, #81759, #32242, .T. ) ; +#69401 = ADVANCED_FACE ( 'NONE', ( #47033 ), #22552, .T. ) ; +#69402 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69403 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61321 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33655, #81630, #41807 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69405 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#69404 = FILL_AREA_STYLE_COLOUR ( '', #78485 ) ; +#69406 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69407 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #52775, #53759, #75733, #100107 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#69408 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66708 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27359, #27881, #50852 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69409 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69410 = VERTEX_POINT ( 'NONE', #84823 ) ; +#69411 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69412 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36671, 'distance_accuracy_value', 'NONE'); +#69413 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99807, 'distance_accuracy_value', 'NONE'); +#69414 = AXIS2_PLACEMENT_3D ( 'NONE', #75215, #83375, #29728 ) ; +#69415 = LINE ( 'NONE', #78127, #43364 ) ; +#69416 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69417 = SURFACE_STYLE_USAGE ( .BOTH. , #37816 ) ; +#69418 = EDGE_CURVE ( 'NONE', #11018, #74498, #23071, .T. ) ; +#69419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69420 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #48166, #9269, #96099, #56366, #71651, #48680, #56854, #2712, #32839, #87462, #57352, #88469, #17494, #84692, #97592, #66491, #74676, #89968, #50211 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.206823832064058647E-05, 2.348066517697088633E-05, 3.424528344027901415E-05, 4.442676613306184894E-05, 5.429788834795175079E-05, 6.393571639820135803E-05, 7.352362677378115820E-05, 8.316220916426971346E-05, 9.280908540432332822E-05, 0.0001024469134545729287, 0.0001120461915498810771, 0.0001218552492073810949, 0.0001317440326063014117, 0.0001420553655807824242, 0.0001526154183617308801, 0.0001635947015071075093 ), + .UNSPECIFIED. ) ; +#69421 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#69422 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#69423 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71137 ) ) ; +#69424 = CARTESIAN_POINT ( 'NONE', ( 0.03652597402597375364, 0.7099999999999999645, 0.5000000000000000000 ) ) ; +#69425 = ADVANCED_FACE ( 'NONE', ( #93465 ), #14838, .T. ) ; +#69426 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#69427 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_DFN1006.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_DFN1006.STEP', '', ( #77515 ) ) ; +#69428 = STYLED_ITEM ( 'NONE', ( #56098 ), #77722 ) ; +#69429 = ORIENTED_EDGE ( 'NONE', *, *, #68067, .F. ) ; +#69430 = ORIENTED_EDGE ( 'NONE', *, *, #34105, .T. ) ; +#69431 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69432 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41372, 'distance_accuracy_value', 'NONE'); +#69433 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54296, 'distance_accuracy_value', 'NONE'); +#69434 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#69435 = FACE_OUTER_BOUND ( 'NONE', #23994, .T. ) ; +#69436 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69437 = CARTESIAN_POINT ( 'NONE', ( 1.060212458128310775, -0.9184269860678199171, 0.8100000000000412426 ) ) ; +#69438 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#69439 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#69440 = ORIENTED_EDGE ( 'NONE', *, *, #58313, .T. ) ; +#69441 = CARTESIAN_POINT ( 'NONE', ( 1.065702489232140060, -1.018544155089240011, 0.8300000000000002931 ) ) ; +#69442 = PLANE ( 'NONE', #58623 ) ; +#69444 = VECTOR ( 'NONE', #12060, 1000.000000000000000 ) ; +#69443 = FACE_OUTER_BOUND ( 'NONE', #73255, .T. ) ; +#69445 = VERTEX_POINT ( 'NONE', #15865 ) ; +#69446 = EDGE_CURVE ( 'NONE', #45227, #16846, #33758, .T. ) ; +#69447 = CARTESIAN_POINT ( 'NONE', ( -1.076179938779914913, 3.099999999999990319, 0.000000000000000000 ) ) ; +#69448 = CIRCLE ( 'NONE', #82547, 0.01000000000000002623 ) ; +#69449 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69450 = ORIENTED_EDGE ( 'NONE', *, *, #7792, .F. ) ; +#69451 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36836, #7092, #6613, #30141, #99511, #22498, #38342, #23025 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000003331, 0.5000000000000006661, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#69452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69453 = CARTESIAN_POINT ( 'NONE', ( 1.115802419441249915, -1.426518300252259897, 0.8100000000000000533 ) ) ; +#69454 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69455 = VECTOR ( 'NONE', #61751, 1000.000000000000000 ) ; +#69456 = PRESENTATION_STYLE_ASSIGNMENT (( #15320 ) ) ; +#69457 = EDGE_CURVE ( 'NONE', #60973, #28450, #1931, .T. ) ; +#69458 = CARTESIAN_POINT ( 'NONE', ( -1.525999994769766666E-07, 9.589999974690677220E-08, 0.02000000000000005246 ) ) ; +#69459 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.000000000000000000 ) ) ; +#69460 = SURFACE_STYLE_USAGE ( .BOTH. , #38361 ) ; +#69461 = LINE ( 'NONE', #7107, #38231 ) ; +#69462 = EDGE_CURVE ( 'NONE', #25100, #92419, #26603, .T. ) ; +#69464 = VERTEX_POINT ( 'NONE', #2108 ) ; +#69463 = ORIENTED_EDGE ( 'NONE', *, *, #37803, .T. ) ; +#69465 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45371 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70772, #318, #8401 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69466 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#69467 = LINE ( 'NONE', #7616, #12007 ) ; +#69468 = ORIENTED_EDGE ( 'NONE', *, *, #82497, .T. ) ; +#69469 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40141 ) ) ; +#69470 = FACE_OUTER_BOUND ( 'NONE', #30190, .T. ) ; +#69472 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.123820061220085265, -0.02000000000000000042 ) ) ; +#69471 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.300000000000000711, 0.000000000000000000 ) ) ; +#69473 = VERTEX_POINT ( 'NONE', #34275 ) ; +#69474 = ORIENTED_EDGE ( 'NONE', *, *, #68077, .T. ) ; +#69475 = CARTESIAN_POINT ( 'NONE', ( -1.383333333333333526, 3.099999999999989875, 0.000000000000000000 ) ) ; +#69476 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69477 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69478 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69480 = FILL_AREA_STYLE_COLOUR ( '', #30462 ) ; +#69479 = FILL_AREA_STYLE ('',( #8632 ) ) ; +#69481 = ORIENTED_EDGE ( 'NONE', *, *, #13579, .T. ) ; +#69482 = ORIENTED_EDGE ( 'NONE', *, *, #67101, .T. ) ; +#69483 = SURFACE_STYLE_USAGE ( .BOTH. , #23064 ) ; +#69484 = ORIENTED_EDGE ( 'NONE', *, *, #38817, .F. ) ; +#69485 = LINE ( 'NONE', #76664, #6769 ) ; +#69486 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17389 ), #56513 ) ; +#69488 = VERTEX_POINT ( 'NONE', #64383 ) ; +#69487 = SURFACE_SIDE_STYLE ('',( #45484 ) ) ; +#69489 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69490 = STYLED_ITEM ( 'NONE', ( #24399 ), #83790 ) ; +#69491 = VECTOR ( 'NONE', #70290, 1000.000000000000000 ) ; +#69492 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#69493 = ORIENTED_EDGE ( 'NONE', *, *, #19801, .T. ) ; +#69494 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69495 = ORIENTED_EDGE ( 'NONE', *, *, #54712, .F. ) ; +#69496 = ADVANCED_FACE ( 'NONE', ( #65370 ), #71550, .T. ) ; +#69497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5913 ) ) ; +#69498 = FACE_OUTER_BOUND ( 'NONE', #24963, .T. ) ; +#69499 = CIRCLE ( 'NONE', #45079, 0.2000000000000005107 ) ; +#69500 = CYLINDRICAL_SURFACE ( 'NONE', #41646, 0.04999999999999999584 ) ; +#69501 = VECTOR ( 'NONE', #56894, 1000.000000000000000 ) ; +#69502 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51938, #83071, #28443 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69503 = EDGE_CURVE ( 'NONE', #72086, #61238, #96496, .T. ) ; +#69505 = ORIENTED_EDGE ( 'NONE', *, *, #48399, .T. ) ; +#69504 = CYLINDRICAL_SURFACE ( 'NONE', #21601, 0.2500000000000000000 ) ; +#69506 = FACE_OUTER_BOUND ( 'NONE', #74808, .T. ) ; +#69507 = CARTESIAN_POINT ( 'NONE', ( 1.673324881778589956, -1.507258815139120189, 0.8299999999999999600 ) ) ; +#69508 = SURFACE_SIDE_STYLE ('',( #46006 ) ) ; +#69509 = LINE ( 'NONE', #15891, #76646 ) ; +#69510 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69511 = SURFACE_STYLE_USAGE ( .BOTH. , #32762 ) ; +#69512 = ORIENTED_EDGE ( 'NONE', *, *, #66309, .T. ) ; +#69513 = EDGE_CURVE ( 'NONE', #80839, #54018, #40412, .T. ) ; +#69514 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69515 = SURFACE_STYLE_FILL_AREA ( #37420 ) ; +#69516 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#69517 = EDGE_CURVE ( 'NONE', #70495, #68510, #72051, .T. ) ; +#69519 = CARTESIAN_POINT ( 'NONE', ( 1.664835065683849979, -1.443372874996269983, 0.8100000000000000533 ) ) ; +#69518 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69520 = FILL_AREA_STYLE_COLOUR ( '', #79683 ) ; +#69521 = FILL_AREA_STYLE ('',( #14369 ) ) ; +#69522 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8991599999999999593 ) ) ; +#69523 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69524 = PRESENTATION_STYLE_ASSIGNMENT (( #52250 ) ) ; +#69525 = FILL_AREA_STYLE_COLOUR ( '', #70300 ) ; +#69526 = ORIENTED_EDGE ( 'NONE', *, *, #60116, .F. ) ; +#69527 = VECTOR ( 'NONE', #88687, 1000.000000000000000 ) ; +#69528 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69529 = ADVANCED_FACE ( 'NONE', ( #88872 ), #2606, .T. ) ; +#69530 = SURFACE_STYLE_USAGE ( .BOTH. , #32773 ) ; +#69531 = EDGE_CURVE ( 'NONE', #99332, #35208, #25109, .T. ) ; +#69532 = STYLED_ITEM ( 'NONE', ( #3722 ), #14334 ) ; +#69533 = ORIENTED_EDGE ( 'NONE', *, *, #88939, .T. ) ; +#69534 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16183, #38695, #62211, #85144 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#69535 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.004999999999999999237, 0.2500000000000000000 ) ) ; +#69536 = EDGE_CURVE ( 'NONE', #88062, #77506, #70078, .T. ) ; +#69538 = ADVANCED_FACE ( 'NONE', ( #72521 ), #49574, .T. ) ; +#69537 = CYLINDRICAL_SURFACE ( 'NONE', #17000, 0.04999999999999991257 ) ; +#69539 = AXIS2_PLACEMENT_3D ( 'NONE', #32345, #2213, #7747 ) ; +#69540 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69541 = ORIENTED_EDGE ( 'NONE', *, *, #65154, .T. ) ; +#69542 = CARTESIAN_POINT ( 'NONE', ( 1.874899521751800080, -1.024811280222130083, 0.8100000000000008304 ) ) ; +#69543 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.008431457505076164760, -0.1458578643762690474 ) ) ; +#69544 = FILL_AREA_STYLE_COLOUR ( '', #53937 ) ; +#69545 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69546 = EDGE_CURVE ( 'NONE', #7518, #74684, #87851, .T. ) ; +#69547 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#69548 = FILL_AREA_STYLE ('',( #78734 ) ) ; +#69550 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69549 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44313 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61718, #45332, #76500 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69551 = VECTOR ( 'NONE', #41820, 1000.000000000000000 ) ; +#69552 = FILL_AREA_STYLE ('',( #38444 ) ) ; +#69553 = EDGE_CURVE ( 'NONE', #95463, #18774, #20172, .T. ) ; +#69554 = CARTESIAN_POINT ( 'NONE', ( 0.04001441731020210363, -0.9622763341455700115, 0.8100000000000000533 ) ) ; +#69555 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#69556 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88081, 'distance_accuracy_value', 'NONE'); +#69557 = LINE ( 'NONE', #76733, #81385 ) ; +#69558 = VERTEX_POINT ( 'NONE', #49069 ) ; +#69559 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69560 = ORIENTED_EDGE ( 'NONE', *, *, #32219, .T. ) ; +#69561 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69562 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54957, 'distance_accuracy_value', 'NONE'); +#69563 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46933, 'distance_accuracy_value', 'NONE'); +#69564 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#69565 = CARTESIAN_POINT ( 'NONE', ( -1.125815218778140059, -1.515241174392790047, 0.8299999999999981837 ) ) ; +#69566 = AXIS2_PLACEMENT_3D ( 'NONE', #83526, #85516, #53380 ) ; +#69567 = CARTESIAN_POINT ( 'NONE', ( -0.1125000000000000167, -1.507792207792209904, 0.8299999999999999600 ) ) ; +#69568 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#69569 = SURFACE_STYLE_USAGE ( .BOTH. , #38460 ) ; +#69570 = CARTESIAN_POINT ( 'NONE', ( -1.876179938779914957, 3.100000000000000533, 0.000000000000000000 ) ) ; +#69571 = VERTEX_POINT ( 'NONE', #33239 ) ; +#69572 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69573 = FILL_AREA_STYLE ('',( #99622 ) ) ; +#69574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62536, 'distance_accuracy_value', 'NONE'); +#69575 = CIRCLE ( 'NONE', #59666, 0.02999999999999997113 ) ; +#69576 = ORIENTED_EDGE ( 'NONE', *, *, #9592, .F. ) ; +#69577 = FILL_AREA_STYLE_COLOUR ( '', #65688 ) ; +#69578 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9244 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96136, #31859, #49217 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69579 = EDGE_LOOP ( 'NONE', ( #62873, #88986, #71689, #56509 ) ) ; +#69580 = PRESENTATION_STYLE_ASSIGNMENT (( #94046 ) ) ; +#69581 = FILL_AREA_STYLE_COLOUR ( '', #77846 ) ; +#69582 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69583 = AXIS2_PLACEMENT_3D ( 'NONE', #67249, #57635, #83092 ) ; +#69584 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69585 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#69586 = PLANE ( 'NONE', #69298 ) ; +#69587 = STYLED_ITEM ( 'NONE', ( #89667 ), #62222 ) ; +#69588 = ADVANCED_FACE ( 'NONE', ( #10138 ), #41903, .T. ) ; +#69589 = ORIENTED_EDGE ( 'NONE', *, *, #15328, .T. ) ; +#69590 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#69591 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21121, 'distance_accuracy_value', 'NONE'); +#69592 = VECTOR ( 'NONE', #12481, 1000.000000000000000 ) ; +#69593 = VECTOR ( 'NONE', #31425, 1000.000000000000000 ) ; +#69594 = EDGE_CURVE ( 'NONE', #36115, #23190, #79192, .T. ) ; +#69595 = ORIENTED_EDGE ( 'NONE', *, *, #77723, .F. ) ; +#69596 = CIRCLE ( 'NONE', #33718, 0.1100000000000007222 ) ; +#69597 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#69598 = SURFACE_STYLE_USAGE ( .BOTH. , #28807 ) ; +#69599 = FILL_AREA_STYLE_COLOUR ( '', #9597 ) ; +#69600 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69601 = ORIENTED_EDGE ( 'NONE', *, *, #99433, .F. ) ; +#69602 = EDGE_LOOP ( 'NONE', ( #42569, #62765, #41463, #62012, #59478, #84801 ) ) ; +#69603 = SURFACE_STYLE_FILL_AREA ( #15470 ) ; +#69604 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42219 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36848, #90450, #99519 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69605 = ORIENTED_EDGE ( 'NONE', *, *, #55244, .T. ) ; +#69606 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64687 ) ) ; +#69607 = EDGE_CURVE ( 'NONE', #46008, #54719, #3450, .T. ) ; +#69608 = ORIENTED_EDGE ( 'NONE', *, *, #30068, .T. ) ; +#69610 = ORIENTED_EDGE ( 'NONE', *, *, #9658, .T. ) ; +#69609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69611 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58842 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51196, #2717, #73658 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69612 = SURFACE_STYLE_USAGE ( .BOTH. , #7264 ) ; +#69614 = FILL_AREA_STYLE ('',( #86472 ) ) ; +#69613 = SURFACE_SIDE_STYLE ('',( #30821 ) ) ; +#69615 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69616 = ORIENTED_EDGE ( 'NONE', *, *, #41219, .T. ) ; +#69617 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69618 = PRESENTATION_STYLE_ASSIGNMENT (( #17011 ) ) ; +#69619 = ORIENTED_EDGE ( 'NONE', *, *, #52604, .T. ) ; +#69620 = EDGE_CURVE ( 'NONE', #49182, #14799, #20919, .T. ) ; +#69621 = CARTESIAN_POINT ( 'NONE', ( -0.03199294643712817521, -1.130688752554405596, 0.8100000000000510125 ) ) ; +#69622 = PLANE ( 'NONE', #95356 ) ; +#69623 = AXIS2_PLACEMENT_3D ( 'NONE', #76140, #90457, #20008 ) ; +#69624 = EDGE_LOOP ( 'NONE', ( #1059, #23289, #87034, #32109 ) ) ; +#69625 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9296 ) ) ; +#69627 = DIRECTION ( 'NONE', ( -4.344024262657780003E-34, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69626 = SURFACE_STYLE_USAGE ( .BOTH. , #6291 ) ; +#69628 = ORIENTED_EDGE ( 'NONE', *, *, #21842, .F. ) ; +#69629 = LINE ( 'NONE', #45618, #92988 ) ; +#69630 = PRESENTATION_STYLE_ASSIGNMENT (( #16505 ) ) ; +#69631 = ADVANCED_FACE ( 'NONE', ( #52087 ), #89855, .T. ) ; +#69632 = VECTOR ( 'NONE', #18326, 1000.000000000000000 ) ; +#69633 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35450 ), #38688 ) ; +#69634 = ORIENTED_EDGE ( 'NONE', *, *, #91403, .F. ) ; +#69635 = VERTEX_POINT ( 'NONE', #90354 ) ; +#69636 = EDGE_CURVE ( 'NONE', #10232, #19609, #60262, .T. ) ; +#69638 = PLANE ( 'NONE', #88241 ) ; +#69637 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69639 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69640 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31778, 'distance_accuracy_value', 'NONE'); +#69641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82659 ), #19151 ) ; +#69642 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#69643 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69644 = PRESENTATION_STYLE_ASSIGNMENT (( #55395 ) ) ; +#69645 = SURFACE_SIDE_STYLE ('',( #70674 ) ) ; +#69646 = EDGE_CURVE ( 'NONE', #55494, #89960, #52576, .T. ) ; +#69647 = SURFACE_SIDE_STYLE ('',( #100683 ) ) ; +#69648 = SURFACE_STYLE_USAGE ( .BOTH. , #52860 ) ; +#69649 = STYLED_ITEM ( 'NONE', ( #90212 ), #16906 ) ; +#69650 = ORIENTED_EDGE ( 'NONE', *, *, #9038, .F. ) ; +#69651 = CARTESIAN_POINT ( 'NONE', ( -1.219528525021920107, -1.135808780994409961, 0.8300000000000002931 ) ) ; +#69652 = VECTOR ( 'NONE', #85512, 1000.000000000000000 ) ; +#69653 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74585 ), #82740 ) ; +#69656 = SURFACE_STYLE_FILL_AREA ( #61041 ) ; +#69655 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.019578823124769955E-44, 4.701977403289150032E-30 ) ) ; +#69654 = FACE_OUTER_BOUND ( 'NONE', #33328, .T. ) ; +#69657 = CARTESIAN_POINT ( 'NONE', ( -1.383450513437169516, 1.393372100993099938, 0.8299999999999999600 ) ) ; +#69658 = FILL_AREA_STYLE ('',( #94657 ) ) ; +#69659 = ADVANCED_FACE ( 'NONE', ( #59776 ), #19913, .T. ) ; +#69660 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69661 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#69662 = CLOSED_SHELL ( 'NONE', ( #84225, #55072, #20714, #75884, #41558, #90544 ) ) ; +#69663 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69664 = VERTEX_POINT ( 'NONE', #27599 ) ; +#69665 = PLANE ( 'NONE', #39138 ) ; +#69666 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12554 ), #25690 ) ; +#69667 = SURFACE_STYLE_FILL_AREA ( #9839 ) ; +#69668 = FILL_AREA_STYLE ('',( #98741 ) ) ; +#69669 = VECTOR ( 'NONE', #23529, 1000.000000000000000 ) ; +#69670 = SURFACE_SIDE_STYLE ('',( #46694 ) ) ; +#69671 = EDGE_CURVE ( 'NONE', #74996, #86461, #58752, .T. ) ; +#69672 = LINE ( 'NONE', #47217, #69652 ) ; +#69673 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69674 = STYLED_ITEM ( 'NONE', ( #91516 ), #50260 ) ; +#69675 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4849999999999999867, -0.2399999999999999911 ) ) ; +#69676 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000025258, 0.1500000000000000222 ) ) ; +#69677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69678 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8648700000000000276 ) ) ; +#69679 = EDGE_CURVE ( 'NONE', #40674, #66883, #96830, .T. ) ; +#69680 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#69681 = FACE_OUTER_BOUND ( 'NONE', #20453, .T. ) ; +#69682 = SURFACE_STYLE_FILL_AREA ( #100217 ) ; +#69683 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#69684 = FILL_AREA_STYLE_COLOUR ( '', #73317 ) ; +#69685 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3080, 'distance_accuracy_value', 'NONE'); +#69686 = VECTOR ( 'NONE', #43336, 1000.000000000000000 ) ; +#69687 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69688 = CARTESIAN_POINT ( 'NONE', ( 1.160615575525245413, 1.293812674402289753, 0.8100000000000000533 ) ) ; +#69689 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61233, 'distance_accuracy_value', 'NONE'); +#69690 = PLANE ( 'NONE', #84591 ) ; +#69691 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, -0.2999999999999999889 ) ) ; +#69692 = SURFACE_STYLE_FILL_AREA ( #91189 ) ; +#69693 = FILL_AREA_STYLE_COLOUR ( '', #50448 ) ; +#69694 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #52229, #97127, #97617, #58397 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#69695 = PRESENTATION_STYLE_ASSIGNMENT (( #38573 ) ) ; +#69696 = ORIENTED_EDGE ( 'NONE', *, *, #61647, .F. ) ; +#69697 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69698 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31204, 'distance_accuracy_value', 'NONE'); +#69699 = LINE ( 'NONE', #86043, #10180 ) ; +#69700 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64694 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96463, #34243, #2075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69701 = VECTOR ( 'NONE', #29690, 1000.000000000000114 ) ; +#69702 = ORIENTED_EDGE ( 'NONE', *, *, #71911, .T. ) ; +#69703 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#69704 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.000000000000000000 ) ) ; +#69705 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.500000000000000444, 0.000000000000000000 ) ) ; +#69706 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69707 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#69708 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69709 = LINE ( 'NONE', #94696, #21829 ) ; +#69710 = ORIENTED_EDGE ( 'NONE', *, *, #71959, .F. ) ; +#69711 = FACE_OUTER_BOUND ( 'NONE', #48200, .T. ) ; +#69712 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100014, 'distance_accuracy_value', 'NONE'); +#69713 = AXIS2_PLACEMENT_3D ( 'NONE', #58705, #21359, #35216 ) ; +#69714 = STYLED_ITEM ( 'NONE', ( #28753 ), #91308 ) ; +#69715 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69716 = EDGE_CURVE ( 'NONE', #27159, #23167, #88373, .T. ) ; +#69717 = SURFACE_STYLE_USAGE ( .BOTH. , #16587 ) ; +#69718 = EDGE_LOOP ( 'NONE', ( #94833, #40495, #66595, #100543 ) ) ; +#69719 = VERTEX_POINT ( 'NONE', #24334 ) ; +#69720 = PLANE ( 'NONE', #50828 ) ; +#69721 = EDGE_LOOP ( 'NONE', ( #5352, #57269, #47889, #66899 ) ) ; +#69722 = SURFACE_STYLE_FILL_AREA ( #7373 ) ; +#69723 = STYLED_ITEM ( 'NONE', ( #30982 ), #79354 ) ; +#69724 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69725 = CARTESIAN_POINT ( 'NONE', ( 0.4793384683631900511, -1.221234985172420018, 0.8299999999999999600 ) ) ; +#69726 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69727 = DIRECTION ( 'NONE', ( -1.000000000000000000, -5.551115123125780237E-17, 3.081487911019574628E-33 ) ) ; +#69728 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #29376, #9931 ) ; +#69729 = FACE_OUTER_BOUND ( 'NONE', #62395, .T. ) ; +#69730 = EDGE_LOOP ( 'NONE', ( #97728, #82313, #52567, #23075, #22357, #42923 ) ) ; +#69731 = VECTOR ( 'NONE', #46039, 1000.000000000000000 ) ; +#69732 = ORIENTED_EDGE ( 'NONE', *, *, #81963, .F. ) ; +#69733 = SURFACE_STYLE_FILL_AREA ( #23812 ) ; +#69734 = STYLED_ITEM ( 'NONE', ( #64705 ), #41775 ) ; +#69735 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45307 ) ) ; +#69736 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69737 = SURFACE_SIDE_STYLE ('',( #22287 ) ) ; +#69738 = CLOSED_SHELL ( 'NONE', ( #36895, #35107, #54498, #80127, #66378, #76888 ) ) ; +#69739 = ORIENTED_EDGE ( 'NONE', *, *, #35045, .F. ) ; +#69740 = EDGE_CURVE ( 'NONE', #25944, #26730, #95217, .T. ) ; +#69741 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16431 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16536, #1243, #97036 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69742 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69743 = STYLED_ITEM ( 'NONE', ( #2386 ), #100727 ) ; +#69744 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69745 = ORIENTED_EDGE ( 'NONE', *, *, #5039, .F. ) ; +#69747 = PRESENTATION_STYLE_ASSIGNMENT (( #13554 ) ) ; +#69746 = CYLINDRICAL_SURFACE ( 'NONE', #38969, 0.05000000000000012768 ) ; +#69748 = VERTEX_POINT ( 'NONE', #7008 ) ; +#69749 = ORIENTED_EDGE ( 'NONE', *, *, #99414, .T. ) ; +#69750 = CARTESIAN_POINT ( 'NONE', ( 1.360085058678500047, -1.308270162923429902, 0.8299999999999999600 ) ) ; +#69751 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45245 ), #58382 ) ; +#69752 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59469 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56767, #39902, #97004 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69753 = FILL_AREA_STYLE ('',( #7902 ) ) ; +#69754 = LINE ( 'NONE', #47294, #70141 ) ; +#69755 = ORIENTED_EDGE ( 'NONE', *, *, #54628, .F. ) ; +#69756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99993 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19490, #74122, #4653 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69757 = PRESENTATION_STYLE_ASSIGNMENT (( #38630 ) ) ; +#69758 = FACE_OUTER_BOUND ( 'NONE', #61264, .T. ) ; +#69759 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 7.720787999999999762, 0.8648700000000000276 ) ) ; +#69760 = EDGE_LOOP ( 'NONE', ( #23551, #79326, #54298, #16872 ) ) ; +#69762 = FACE_OUTER_BOUND ( 'NONE', #66450, .T. ) ; +#69761 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69763 = CARTESIAN_POINT ( 'NONE', ( 0.4645119866146578125, 0.3274465759269653553, 0.8100000000000000533 ) ) ; +#69764 = ORIENTED_EDGE ( 'NONE', *, *, #3416, .F. ) ; +#69765 = VERTEX_POINT ( 'NONE', #40145 ) ; +#69766 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#69767 = ADVANCED_FACE ( 'NONE', ( #45361 ), #46856, .T. ) ; +#69768 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69770 = FILL_AREA_STYLE_COLOUR ( '', #74857 ) ; +#69769 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#69771 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#69772 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#69773 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#69774 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69775 = CARTESIAN_POINT ( 'NONE', ( -0.01680389005683929904, -1.106837409965790053, 0.8100000000000000533 ) ) ; +#69776 = FILL_AREA_STYLE_COLOUR ( '', #86637 ) ; +#69777 = STYLED_ITEM ( 'NONE', ( #50770 ), #31314 ) ; +#69778 = ORIENTED_EDGE ( 'NONE', *, *, #15962, .F. ) ; +#69779 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69780 = ORIENTED_EDGE ( 'NONE', *, *, #5603, .F. ) ; +#69781 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333333304, 2.500000000000000000, 1.747825839085088807E-76 ) ) ; +#69782 = VECTOR ( 'NONE', #53686, 1000.000000000000000 ) ; +#69783 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69784 = EDGE_CURVE ( 'NONE', #83900, #13569, #68366, .T. ) ; +#69785 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27406 ), #60085 ) ; +#69786 = VECTOR ( 'NONE', #69547, 999.9999999999998863 ) ; +#69787 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69788 = FILL_AREA_STYLE_COLOUR ( '', #51750 ) ; +#69789 = SURFACE_SIDE_STYLE ('',( #71323 ) ) ; +#69791 = ORIENTED_EDGE ( 'NONE', *, *, #44395, .T. ) ; +#69790 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69792 = FACE_OUTER_BOUND ( 'NONE', #29828, .T. ) ; +#69793 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69794 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1199999999999999956, -1.000000000000000000 ) ) ; +#69795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #791, 'distance_accuracy_value', 'NONE'); +#69796 = LINE ( 'NONE', #77989, #92389 ) ; +#69797 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69798 = LINE ( 'NONE', #62691, #84026 ) ; +#69799 = EDGE_CURVE ( 'NONE', #81483, #146, #43140, .T. ) ; +#69800 = PRESENTATION_STYLE_ASSIGNMENT (( #15669 ) ) ; +#69801 = VECTOR ( 'NONE', #20667, 1000.000000000000000 ) ; +#69802 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69803 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#69804 = SURFACE_STYLE_USAGE ( .BOTH. , #7951 ) ; +#69805 = LINE ( 'NONE', #70835, #95822 ) ; +#69806 = VECTOR ( 'NONE', #55007, 1000.000000000000000 ) ; +#69807 = SURFACE_STYLE_FILL_AREA ( #62695 ) ; +#69808 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#69809 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#69810 = CARTESIAN_POINT ( 'NONE', ( 1.224015772021439963, -0.9561532343638800002, 0.8299999999999995159 ) ) ; +#69811 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69812 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #28630, 'design' ) ; +#69813 = CLOSED_SHELL ( 'NONE', ( #85670, #95670, #84420, #2079, #22666, #64269 ) ) ; +#69814 = FILL_AREA_STYLE ('',( #38689 ) ) ; +#69815 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#69816 = EDGE_LOOP ( 'NONE', ( #73648, #17512, #96785, #22161 ) ) ; +#69817 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69818 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#69819 = PRESENTATION_STYLE_ASSIGNMENT (( #77487 ) ) ; +#69820 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69821 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52710, 'distance_accuracy_value', 'NONE'); +#69822 = LINE ( 'NONE', #100844, #91592 ) ; +#69823 = STYLED_ITEM ( 'NONE', ( #39668 ), #50725 ) ; +#69824 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69825 = FILL_AREA_STYLE_COLOUR ( '', #89584 ) ; +#69826 = PRESENTATION_STYLE_ASSIGNMENT (( #55058 ) ) ; +#69827 = EDGE_CURVE ( 'NONE', #20920, #1969, #89118, .T. ) ; +#69828 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63331 ) ) ; +#69829 = ORIENTED_EDGE ( 'NONE', *, *, #39300, .F. ) ; +#69830 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68223 ) ) ; +#69831 = LINE ( 'NONE', #100853, #49469 ) ; +#69832 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69833 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23945, 'distance_accuracy_value', 'NONE'); +#69834 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8991599999999999593 ) ) ; +#69835 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44749, 'distance_accuracy_value', 'NONE'); +#69836 = EDGE_CURVE ( 'NONE', #25853, #87484, #3517, .T. ) ; +#69837 = LINE ( 'NONE', #77009, #94139 ) ; +#69838 = SURFACE_STYLE_FILL_AREA ( #87580 ) ; +#69839 = EDGE_LOOP ( 'NONE', ( #68424, #96068, #93062, #10103 ) ) ; +#69840 = ORIENTED_EDGE ( 'NONE', *, *, #16344, .F. ) ; +#69841 = FACE_OUTER_BOUND ( 'NONE', #13797, .T. ) ; +#69842 = EDGE_LOOP ( 'NONE', ( #72928, #79483, #20995, #13592 ) ) ; +#69843 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69844 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94332 ), #17734 ) ; +#69845 = SURFACE_STYLE_USAGE ( .BOTH. , #38723 ) ; +#69846 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69847 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69848 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62565, 'distance_accuracy_value', 'NONE'); +#69849 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999992006, -3.500000000000000444, 0.000000000000000000 ) ) ; +#69850 = VECTOR ( 'NONE', #94906, 1000.000000000000114 ) ; +#69851 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #73668 ) ; +#69852 = SURFACE_STYLE_FILL_AREA ( #23944 ) ; +#69853 = FILL_AREA_STYLE_COLOUR ( '', #94637 ) ; +#69855 = VERTEX_POINT ( 'NONE', #72792 ) ; +#69854 = ORIENTED_EDGE ( 'NONE', *, *, #82889, .F. ) ; +#69856 = ORIENTED_EDGE ( 'NONE', *, *, #68944, .F. ) ; +#69857 = FILL_AREA_STYLE ('',( #69323 ) ) ; +#69858 = STYLED_ITEM ( 'NONE', ( #36465 ), #84744 ) ; +#69859 = STYLED_ITEM ( 'NONE', ( #76108 ), #91510 ) ; +#69860 = CARTESIAN_POINT ( 'NONE', ( 1.775025884298160106, -1.496872818153279994, 0.8299999999999999600 ) ) ; +#69861 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.500000000000000000, 0.000000000000000000 ) ) ; +#69862 = ORIENTED_EDGE ( 'NONE', *, *, #28750, .F. ) ; +#69863 = STYLED_ITEM ( 'NONE', ( #54544 ), #55573 ) ; +#69864 = EDGE_CURVE ( 'NONE', #46763, #96899, #18190, .T. ) ; +#69865 = FILL_AREA_STYLE ('',( #99901 ) ) ; +#69866 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#69867 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69868 = SURFACE_STYLE_FILL_AREA ( #86721 ) ; +#69869 = ORIENTED_EDGE ( 'NONE', *, *, #74662, .F. ) ; +#69870 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#69871 = EDGE_LOOP ( 'NONE', ( #65197, #15982, #24599, #38451 ) ) ; +#69872 = EDGE_CURVE ( 'NONE', #76182, #29895, #13982, .T. ) ; +#69873 = ORIENTED_EDGE ( 'NONE', *, *, #5300, .F. ) ; +#69874 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32376 ), #51991 ) ; +#69875 = STYLED_ITEM ( 'NONE', ( #44087 ), #63304 ) ; +#69876 = VECTOR ( 'NONE', #32527, 1000.000000000000000 ) ; +#69877 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#69878 = ORIENTED_EDGE ( 'NONE', *, *, #65461, .T. ) ; +#69879 = VECTOR ( 'NONE', #57581, 1000.000000000000000 ) ; +#69880 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69881 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69882 = ORIENTED_EDGE ( 'NONE', *, *, #98643, .F. ) ; +#69883 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69884 = AXIS2_PLACEMENT_3D ( 'NONE', #37151, #91732, #52977 ) ; +#69885 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#69886 = VERTEX_POINT ( 'NONE', #4344 ) ; +#69887 = EDGE_LOOP ( 'NONE', ( #31698, #4228, #66949, #1711 ) ) ; +#69888 = EDGE_CURVE ( 'NONE', #95260, #75526, #81489, .T. ) ; +#69889 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#69890 = ADVANCED_FACE ( 'NONE', ( #34517 ), #19670, .T. ) ; +#69891 = LINE ( 'NONE', #9055, #41589 ) ; +#69892 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69893 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68216 ) ) ; +#69894 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#69895 = PLANE ( 'NONE', #58652 ) ; +#69896 = FACE_OUTER_BOUND ( 'NONE', #16231, .T. ) ; +#69897 = AXIS2_PLACEMENT_3D ( 'NONE', #31355, #63039, #78833 ) ; +#69898 = VERTEX_POINT ( 'NONE', #65124 ) ; +#69899 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8100000000000000533 ) ) ; +#69900 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, 0.000000000000000000 ) ) ; +#69901 = EDGE_LOOP ( 'NONE', ( #58653, #67336, #16811, #33740 ) ) ; +#69902 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#69903 = VECTOR ( 'NONE', #72999, 1000.000000000000000 ) ; +#69904 = FILL_AREA_STYLE_COLOUR ( '', #92436 ) ; +#69906 = EDGE_CURVE ( 'NONE', #5714, #89914, #90102, .T. ) ; +#69905 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#69907 = CYLINDRICAL_SURFACE ( 'NONE', #27441, 0.04999999999999999584 ) ; +#69909 = PLANE ( 'NONE', #10718 ) ; +#69908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#69910 = SURFACE_SIDE_STYLE ('',( #61300 ) ) ; +#69911 = LINE ( 'NONE', #32658, #66388 ) ; +#69912 = SURFACE_STYLE_FILL_AREA ( #62806 ) ; +#69913 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#69914 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 3.676137000000000210, 0.8991599999999999593 ) ) ; +#69915 = LINE ( 'NONE', #76581, #96648 ) ; +#69916 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#69917 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.1600000000000000033, -1.129999999999999893 ) ) ; +#69918 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.000000000000000000 ) ) ; +#69919 = EDGE_CURVE ( 'NONE', #42447, #18257, #26342, .T. ) ; +#69920 = STYLED_ITEM ( 'NONE', ( #14992 ), #92701 ) ; +#69921 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#69922 = ADVANCED_FACE ( 'NONE', ( #2350 ), #64623, .T. ) ; +#69924 = SURFACE_STYLE_FILL_AREA ( #78599 ) ; +#69923 = SURFACE_STYLE_FILL_AREA ( #6080 ) ; +#69925 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69926 = SURFACE_SIDE_STYLE ('',( #22997 ) ) ; +#69927 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69928 = AXIS2_PLACEMENT_3D ( 'NONE', #94171, #71224, #71738 ) ; +#69929 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69141, 'distance_accuracy_value', 'NONE'); +#69930 = ORIENTED_EDGE ( 'NONE', *, *, #94811, .F. ) ; +#69931 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69932 = FACE_OUTER_BOUND ( 'NONE', #81727, .T. ) ; +#69933 = AXIS2_PLACEMENT_3D ( 'NONE', #61583, #94684, #24809 ) ; +#69934 = VECTOR ( 'NONE', #72013, 1000.000000000000000 ) ; +#69935 = LINE ( 'NONE', #63826, #7184 ) ; +#69936 = SURFACE_SIDE_STYLE ('',( #64692 ) ) ; +#69937 = LINE ( 'NONE', #31156, #20759 ) ; +#69938 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#69939 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65089 ), #42218 ) ; +#69940 = SURFACE_STYLE_USAGE ( .BOTH. , #77617 ) ; +#69941 = PLANE ( 'NONE', #43158 ) ; +#69942 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#69943 = EDGE_CURVE ( 'NONE', #24092, #81543, #50604, .T. ) ; +#69944 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42296 ), #1545 ) ; +#69945 = ORIENTED_EDGE ( 'NONE', *, *, #56579, .T. ) ; +#69946 = ORIENTED_EDGE ( 'NONE', *, *, #26311, .T. ) ; +#69947 = VECTOR ( 'NONE', #76826, 1000.000000000000000 ) ; +#69948 = SURFACE_STYLE_FILL_AREA ( #86293 ) ; +#69949 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#69950 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, -11.57000000000000028 ) ) ; +#69952 = AXIS2_PLACEMENT_3D ( 'NONE', #76247, #52786, #70088 ) ; +#69951 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#69953 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000025258, 0.2500000000000000000 ) ) ; +#69954 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#69955 = PRESENTATION_STYLE_ASSIGNMENT (( #32698 ) ) ; +#69956 = SURFACE_STYLE_USAGE ( .BOTH. , #30140 ) ; +#69957 = PLANE ( 'NONE', #21171 ) ; +#69958 = LINE ( 'NONE', #53659, #80377 ) ; +#69959 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29238 ) ) ; +#69960 = ORIENTED_EDGE ( 'NONE', *, *, #2074, .T. ) ; +#69961 = EDGE_CURVE ( 'NONE', #89439, #49575, #45118, .T. ) ; +#69962 = CARTESIAN_POINT ( 'NONE', ( 1.077065871219029969, -0.9985765647821309710, 0.8300000000000002931 ) ) ; +#69963 = PRESENTATION_STYLE_ASSIGNMENT (( #2435 ) ) ; +#69964 = FILL_AREA_STYLE ('',( #38845 ) ) ; +#69965 = VERTEX_POINT ( 'NONE', #98688 ) ; +#69966 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#69967 = LINE ( 'NONE', #15314, #55006 ) ; +#69968 = ORIENTED_EDGE ( 'NONE', *, *, #22877, .F. ) ; +#69969 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52012 ) ) ; +#69970 = ADVANCED_FACE ( 'NONE', ( #100162 ), #45602, .F. ) ; +#69971 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#69972 = CARTESIAN_POINT ( 'NONE', ( 1.044215815879510068, -1.351519064127929992, 0.8299999999999999600 ) ) ; +#69973 = FACE_OUTER_BOUND ( 'NONE', #10935, .T. ) ; +#69974 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#69975 = CARTESIAN_POINT ( 'NONE', ( 13.08100000000000129, 6.502400000000000624, 0.8991599999999999593 ) ) ; +#69976 = CARTESIAN_POINT ( 'NONE', ( 1.841287855068439949, -1.152628822534790043, 0.8100000000000000533 ) ) ; +#69977 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, 0.000000000000000000 ) ) ; +#69978 = CARTESIAN_POINT ( 'NONE', ( -0.5238200612200851758, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#69979 = EDGE_CURVE ( 'NONE', #12805, #54332, #69085, .T. ) ; +#69981 = VERTEX_POINT ( 'NONE', #82474 ) ; +#69980 = ORIENTED_EDGE ( 'NONE', *, *, #92561, .F. ) ; +#69983 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79668 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78508, #7971, #70864 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#69982 = PRESENTATION_STYLE_ASSIGNMENT (( #62360 ) ) ; +#69984 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -13.40000000000000036 ) ) ; +#69985 = ORIENTED_EDGE ( 'NONE', *, *, #65240, .F. ) ; +#69986 = FACE_OUTER_BOUND ( 'NONE', #29967, .T. ) ; +#69987 = VERTEX_POINT ( 'NONE', #13961 ) ; +#69988 = EDGE_LOOP ( 'NONE', ( #68113, #50044, #67516, #47176 ) ) ; +#69989 = LINE ( 'NONE', #71532, #8678 ) ; +#69990 = VECTOR ( 'NONE', #32939, 1000.000000000000000 ) ; +#69991 = STYLED_ITEM ( 'NONE', ( #63142 ), #75305 ) ; +#69992 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#69993 = LINE ( 'NONE', #68972, #54453 ) ; +#69994 = ORIENTED_EDGE ( 'NONE', *, *, #6556, .F. ) ; +#69995 = VERTEX_POINT ( 'NONE', #30305 ) ; +#69996 = ADVANCED_FACE ( 'NONE', ( #20152 ), #6285, .T. ) ; +#69997 = VERTEX_POINT ( 'NONE', #691 ) ; +#69998 = EDGE_CURVE ( 'NONE', #21063, #61650, #53120, .T. ) ; +#69999 = LINE ( 'NONE', #72047, #83479 ) ; +#70000 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70001 = STYLED_ITEM ( 'NONE', ( #77349 ), #31965 ) ; +#70003 = ORIENTED_EDGE ( 'NONE', *, *, #11486, .F. ) ; +#70002 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70004 = FILL_AREA_STYLE ('',( #93959 ) ) ; +#70005 = SURFACE_STYLE_FILL_AREA ( #45994 ) ; +#70006 = SURFACE_STYLE_USAGE ( .BOTH. , #15357 ) ; +#70007 = PRESENTATION_STYLE_ASSIGNMENT (( #52703 ) ) ; +#70008 = VERTEX_POINT ( 'NONE', #31334 ) ; +#70009 = VECTOR ( 'NONE', #34832, 1000.000000000000000 ) ; +#70010 = FACE_OUTER_BOUND ( 'NONE', #49272, .T. ) ; +#70011 = EDGE_LOOP ( 'NONE', ( #95238, #73937, #24558, #3373 ) ) ; +#70012 = EDGE_CURVE ( 'NONE', #36865, #13287, #3203, .T. ) ; +#70013 = STYLED_ITEM ( 'NONE', ( #19245 ), #6168 ) ; +#70014 = CARTESIAN_POINT ( 'NONE', ( -0.008621852316070110350, -0.9218577280486121017, 0.8299999999999988498 ) ) ; +#70015 = EDGE_CURVE ( 'NONE', #17365, #65537, #7762, .T. ) ; +#70016 = VECTOR ( 'NONE', #8310, 1000.000000000000000 ) ; +#70017 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#70019 = VERTEX_POINT ( 'NONE', #62510 ) ; +#70018 = FILL_AREA_STYLE ('',( #78691 ) ) ; +#70020 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70021 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#70022 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70023 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84883 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23996, #1503, #77079 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70025 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70026 = STYLED_ITEM ( 'NONE', ( #75464 ), #1559 ) ; +#70027 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70028 = ORIENTED_EDGE ( 'NONE', *, *, #45341, .T. ) ; +#70029 = SURFACE_SIDE_STYLE ('',( #68518 ) ) ; +#70030 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70031 = STYLED_ITEM ( 'NONE', ( #64180 ), #42478 ) ; +#70033 = EDGE_CURVE ( 'NONE', #60837, #20645, #8774, .T. ) ; +#70032 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.500000000000000222, 0.1829999999999580296 ) ) ; +#70034 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70036 = FACE_OUTER_BOUND ( 'NONE', #35399, .T. ) ; +#70035 = FACE_OUTER_BOUND ( 'NONE', #41049, .T. ) ; +#70037 = FILL_AREA_STYLE_COLOUR ( '', #28761 ) ; +#70038 = EDGE_CURVE ( 'NONE', #4568, #86742, #70129, .T. ) ; +#70039 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.099999999999999867, 8.599018957360380094E-79 ) ) ; +#70040 = ORIENTED_EDGE ( 'NONE', *, *, #17078, .F. ) ; +#70041 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70042 = VERTEX_POINT ( 'NONE', #40539 ) ; +#70043 = EDGE_CURVE ( 'NONE', #72987, #52930, #47671, .T. ) ; +#70044 = PRESENTATION_STYLE_ASSIGNMENT (( #46559 ) ) ; +#70045 = EDGE_CURVE ( 'NONE', #81345, #37734, #39501, .T. ) ; +#70046 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70047 = SURFACE_STYLE_USAGE ( .BOTH. , #7182 ) ; +#70048 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17871 ), #1579 ) ; +#70049 = LINE ( 'NONE', #68539, #36392 ) ; +#70050 = VERTEX_POINT ( 'NONE', #63526 ) ; +#70051 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#70052 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#70053 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70054 = LINE ( 'NONE', #49634, #73492 ) ; +#70055 = LINE ( 'NONE', #30744, #7350 ) ; +#70056 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.000000000000000000 ) ) ; +#70057 = SURFACE_STYLE_FILL_AREA ( #24660 ) ; +#70058 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#70059 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70060 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#70061 = PLANE ( 'NONE', #58922 ) ; +#70062 = CARTESIAN_POINT ( 'NONE', ( -0.02383637504043630354, -0.9153515042605530061, 0.8100000000000000533 ) ) ; +#70063 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70064 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999334, 0.000000000000000000 ) ) ; +#70065 = ADVANCED_FACE ( 'NONE', ( #54331 ), #93576, .T. ) ; +#70066 = EDGE_LOOP ( 'NONE', ( #67990, #33595, #2722, #61144, #41615, #12468 ) ) ; +#70067 = ORIENTED_EDGE ( 'NONE', *, *, #51391, .F. ) ; +#70068 = PRESENTATION_STYLE_ASSIGNMENT (( #31277 ) ) ; +#70069 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71776 ), #76641 ) ; +#70070 = LINE ( 'NONE', #56326, #47894 ) ; +#70071 = VECTOR ( 'NONE', #71758, 1000.000000000000000 ) ; +#70073 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70072 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64701 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33713, #34727, #18850 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70074 = FACE_OUTER_BOUND ( 'NONE', #18108, .T. ) ; +#70075 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#70076 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70077 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44067 ) ) ; +#70079 = EDGE_LOOP ( 'NONE', ( #78537, #90371, #81836, #7013 ) ) ; +#70078 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95481, #56236, #64371, #2593 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70080 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#70081 = ADVANCED_FACE ( 'NONE', ( #84949 ), #46118, .T. ) ; +#70082 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333326642, 0.5000000000000000000, 1.747825839084889375E-76 ) ) ; +#70083 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#70084 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, -0.2500000000000000000 ) ) ; +#70085 = ORIENTED_EDGE ( 'NONE', *, *, #2558, .F. ) ; +#70086 = SURFACE_SIDE_STYLE ('',( #15448 ) ) ; +#70088 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70087 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47282 ), #34287 ) ; +#70089 = ORIENTED_EDGE ( 'NONE', *, *, #49080, .F. ) ; +#70090 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70091 = ADVANCED_FACE ( 'NONE', ( #88494 ), #79841, .T. ) ; +#70092 = SURFACE_STYLE_USAGE ( .BOTH. , #8737 ) ; +#70093 = AXIS2_PLACEMENT_3D ( 'NONE', #95262, #2894, #24890 ) ; +#70094 = FILL_AREA_STYLE ('',( #71641 ) ) ; +#70095 = SURFACE_STYLE_FILL_AREA ( #38976 ) ; +#70096 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70097 = EDGE_CURVE ( 'NONE', #48067, #99914, #33893, .T. ) ; +#70098 = ORIENTED_EDGE ( 'NONE', *, *, #23276, .T. ) ; +#70099 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19624 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89751, #43290, #60163 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70100 = LINE ( 'NONE', #14936, #35869 ) ; +#70101 = PLANE ( 'NONE', #47887 ) ; +#70102 = SURFACE_STYLE_FILL_AREA ( #16457 ) ; +#70103 = CARTESIAN_POINT ( 'NONE', ( 0.4587323827270540222, -1.026347246440100003, 0.8300000000000002931 ) ) ; +#70104 = ORIENTED_EDGE ( 'NONE', *, *, #91343, .T. ) ; +#70105 = VECTOR ( 'NONE', #98427, 1000.000000000000114 ) ; +#70106 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#70107 = LINE ( 'NONE', #92083, #42429 ) ; +#70108 = SURFACE_STYLE_FILL_AREA ( #16463 ) ; +#70109 = LINE ( 'NONE', #53802, #97683 ) ; +#70110 = AXIS2_PLACEMENT_3D ( 'NONE', #57177, #49497, #80651 ) ; +#70111 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70112 = ORIENTED_EDGE ( 'NONE', *, *, #98050, .F. ) ; +#70113 = EDGE_LOOP ( 'NONE', ( #70178, #36734, #81961, #94840 ) ) ; +#70114 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#70115 = ORIENTED_EDGE ( 'NONE', *, *, #30227, .T. ) ; +#70116 = ADVANCED_FACE ( 'NONE', ( #26729 ), #50721, .F. ) ; +#70117 = AXIS2_PLACEMENT_3D ( 'NONE', #69971, #1566, #40882 ) ; +#70118 = ORIENTED_EDGE ( 'NONE', *, *, #83299, .T. ) ; +#70120 = EDGE_LOOP ( 'NONE', ( #54610, #39820, #19422, #21946 ) ) ; +#70119 = LINE ( 'NONE', #84940, #83582 ) ; +#70121 = PRESENTATION_STYLE_ASSIGNMENT (( #69612 ) ) ; +#70123 = SURFACE_STYLE_USAGE ( .BOTH. , #53817 ) ; +#70122 = DIRECTION ( 'NONE', ( -2.168404344971010347E-16, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70124 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70125 = FILL_AREA_STYLE ('',( #6754 ) ) ; +#70126 = ORIENTED_EDGE ( 'NONE', *, *, #50848, .F. ) ; +#70127 = FACE_OUTER_BOUND ( 'NONE', #25372, .T. ) ; +#70128 = FILL_AREA_STYLE ('',( #38004 ) ) ; +#70129 = LINE ( 'NONE', #78322, #63868 ) ; +#70130 = ORIENTED_EDGE ( 'NONE', *, *, #71276, .F. ) ; +#70131 = LINE ( 'NONE', #41051, #74206 ) ; +#70132 = LINE ( 'NONE', #93579, #41547 ) ; +#70133 = EDGE_CURVE ( 'NONE', #93672, #62366, #99066, .T. ) ; +#70134 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70135 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70136 = ORIENTED_EDGE ( 'NONE', *, *, #45699, .T. ) ; +#70138 = FACE_OUTER_BOUND ( 'NONE', #70706, .T. ) ; +#70137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70139 = ORIENTED_EDGE ( 'NONE', *, *, #50382, .F. ) ; +#70140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94547 ) ) ; +#70141 = VECTOR ( 'NONE', #55501, 1000.000000000000000 ) ; +#70143 = SURFACE_STYLE_USAGE ( .BOTH. , #53833 ) ; +#70142 = PLANE ( 'NONE', #23445 ) ; +#70144 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#70145 = STYLED_ITEM ( 'NONE', ( #60157 ), #57708 ) ; +#70146 = CARTESIAN_POINT ( 'NONE', ( 0.1930873560432360136, -1.357759925407370227, 0.8299999999999982947 ) ) ; +#70147 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13019 ), #32724 ) ; +#70148 = VECTOR ( 'NONE', #88895, 1000.000000000000000 ) ; +#70149 = EDGE_LOOP ( 'NONE', ( #8519, #7749, #35309, #74747 ) ) ; +#70150 = EDGE_LOOP ( 'NONE', ( #37476, #12081, #5844, #79929, #96619, #37140 ) ) ; +#70151 = VECTOR ( 'NONE', #8615, 1000.000000000000000 ) ; +#70153 = SURFACE_STYLE_USAGE ( .BOTH. , #48217 ) ; +#70152 = FILL_AREA_STYLE ('',( #93100 ) ) ; +#70154 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70155 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#70156 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73404 ) ) ; +#70157 = LINE ( 'NONE', #31363, #29692 ) ; +#70158 = AXIS2_PLACEMENT_3D ( 'NONE', #42707, #15793, #17689 ) ; +#70159 = PRESENTATION_STYLE_ASSIGNMENT (( #54367 ) ) ; +#70160 = FACE_BOUND ( 'NONE', #20249, .T. ) ; +#70161 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70162 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#70163 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70164 = ORIENTED_EDGE ( 'NONE', *, *, #87474, .F. ) ; +#70165 = CARTESIAN_POINT ( 'NONE', ( -1.258104321733710007, -1.118172950060400073, 0.8300000000000002931 ) ) ; +#70166 = SURFACE_STYLE_USAGE ( .BOTH. , #61037 ) ; +#70167 = ADVANCED_FACE ( 'NONE', ( #29707 ), #21548, .T. ) ; +#70169 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70168 = SURFACE_STYLE_USAGE ( .BOTH. , #85491 ) ; +#70170 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61660, 'distance_accuracy_value', 'NONE'); +#70171 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55505 ), #92954 ) ; +#70172 = SURFACE_STYLE_USAGE ( .BOTH. , #62557 ) ; +#70173 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70174 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#70175 = CARTESIAN_POINT ( 'NONE', ( 5.646583499499824299, 2.700329500500174618, 0.8991599999999999593 ) ) ; +#70176 = EDGE_CURVE ( 'NONE', #27266, #47955, #99654, .T. ) ; +#70177 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70178 = ORIENTED_EDGE ( 'NONE', *, *, #41926, .F. ) ; +#70179 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999689, -3.383333333333333304, 0.000000000000000000 ) ) ; +#70180 = FACE_OUTER_BOUND ( 'NONE', #66535, .T. ) ; +#70181 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70182 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70183 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70184 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70185 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70186 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21293 ), #40858 ) ; +#70187 = SURFACE_SIDE_STYLE ('',( #79905 ) ) ; +#70188 = SURFACE_SIDE_STYLE ('',( #69682 ) ) ; +#70189 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70190 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70191 = EDGE_CURVE ( 'NONE', #5935, #50788, #5097, .T. ) ; +#70192 = PLANE ( 'NONE', #19312 ) ; +#70193 = LINE ( 'NONE', #85015, #38293 ) ; +#70194 = VERTEX_POINT ( 'NONE', #36883 ) ; +#70195 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8092 ) ) ; +#70196 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220779480, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#70197 = CARTESIAN_POINT ( 'NONE', ( 0.3050025479630040226, -1.260362508506799983, 0.8100000000000000533 ) ) ; +#70198 = CARTESIAN_POINT ( 'NONE', ( 7.064730999999999206, 10.37243899999999996, 0.8648700000000000276 ) ) ; +#70199 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70200 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 10.45022100000000087, 0.8991599999999999593 ) ) ; +#70201 = CARTESIAN_POINT ( 'NONE', ( -1.289672647804670058, -1.082231071007949907, 0.8299999999999999600 ) ) ; +#70202 = ORIENTED_EDGE ( 'NONE', *, *, #8085, .T. ) ; +#70203 = FACE_OUTER_BOUND ( 'NONE', #18837, .T. ) ; +#70204 = EDGE_CURVE ( 'NONE', #99555, #42765, #98082, .T. ) ; +#70205 = FILL_AREA_STYLE_COLOUR ( '', #58413 ) ; +#70206 = STYLED_ITEM ( 'NONE', ( #2817 ), #33603 ) ; +#70207 = FILL_AREA_STYLE ('',( #6839 ) ) ; +#70208 = ORIENTED_EDGE ( 'NONE', *, *, #68722, .F. ) ; +#70209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70210 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70211 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68604 ), #96300 ) ; +#70212 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39243 ) ) ; +#70213 = SURFACE_SIDE_STYLE ('',( #47758 ) ) ; +#70214 = LINE ( 'NONE', #84533, #5944 ) ; +#70215 = VECTOR ( 'NONE', #92283, 1000.000000000000000 ) ; +#70216 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70217 = FILL_AREA_STYLE ('',( #7359 ) ) ; +#70218 = EDGE_CURVE ( 'NONE', #54776, #58057, #82352, .T. ) ; +#70219 = VERTEX_POINT ( 'NONE', #74691 ) ; +#70220 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70221 = VECTOR ( 'NONE', #81260, 999.9999999999998863 ) ; +#70223 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.2300000000000000100, 0.5799137866959189758 ) ) ; +#70222 = STYLED_ITEM ( 'NONE', ( #69982 ), #85764 ) ; +#70224 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7016, 'distance_accuracy_value', 'NONE'); +#70225 = VECTOR ( 'NONE', #33405, 1000.000000000000000 ) ; +#70226 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70227 = EDGE_CURVE ( 'NONE', #3470, #7082, #75673, .T. ) ; +#70228 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70229 = VECTOR ( 'NONE', #51461, 1000.000000000000000 ) ; +#70230 = EDGE_LOOP ( 'NONE', ( #27083, #9337, #41498, #76248 ) ) ; +#70231 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#70232 = ORIENTED_EDGE ( 'NONE', *, *, #54520, .F. ) ; +#70233 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#70234 = CARTESIAN_POINT ( 'NONE', ( 0.002442604188005680164, -1.482878949593630091, 0.8299999999999999600 ) ) ; +#70235 = FACE_OUTER_BOUND ( 'NONE', #98430, .T. ) ; +#70236 = SURFACE_STYLE_FILL_AREA ( #14570 ) ; +#70237 = FILL_AREA_STYLE ('',( #68710 ) ) ; +#70238 = EDGE_CURVE ( 'NONE', #49302, #78769, #53208, .T. ) ; +#70239 = EDGE_CURVE ( 'NONE', #100104, #22518, #12704, .T. ) ; +#70240 = VECTOR ( 'NONE', #70046, 1000.000000000000000 ) ; +#70241 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11430 ) ) ; +#70242 = VECTOR ( 'NONE', #40149, 1000.000000000000000 ) ; +#70243 = ADVANCED_FACE ( 'NONE', ( #14344 ), #45492, .T. ) ; +#70244 = ORIENTED_EDGE ( 'NONE', *, *, #40639, .F. ) ; +#70245 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15358, 'distance_accuracy_value', 'NONE'); +#70246 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86489, #79343, #18016, #32877 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70247 = LINE ( 'NONE', #39117, #3351 ) ; +#70249 = PRESENTATION_STYLE_ASSIGNMENT (( #7886 ) ) ; +#70248 = PRESENTATION_STYLE_ASSIGNMENT (( #15604 ) ) ; +#70250 = ORIENTED_EDGE ( 'NONE', *, *, #3936, .F. ) ; +#70251 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#70252 = FILL_AREA_STYLE_COLOUR ( '', #67517 ) ; +#70253 = EDGE_CURVE ( 'NONE', #18067, #82841, #22556, .T. ) ; +#70254 = PLANE ( 'NONE', #25400 ) ; +#70255 = STYLED_ITEM ( 'NONE', ( #250 ), #51568 ) ; +#70256 = EDGE_LOOP ( 'NONE', ( #81481, #12280, #39301, #19094 ) ) ; +#70258 = FACE_OUTER_BOUND ( 'NONE', #75034, .T. ) ; +#70257 = FILL_AREA_STYLE_COLOUR ( '', #6307 ) ; +#70259 = ORIENTED_EDGE ( 'NONE', *, *, #65189, .F. ) ; +#70260 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24798 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99417, #84197, #30048 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70261 = EDGE_LOOP ( 'NONE', ( #48735, #38922, #10920, #56759 ) ) ; +#70262 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#70263 = CARTESIAN_POINT ( 'NONE', ( -0.8560791624706871605, 0.5647286298174479802, 0.8100000000000000533 ) ) ; +#70264 = EDGE_CURVE ( 'NONE', #46450, #4592, #47038, .T. ) ; +#70266 = PRESENTATION_STYLE_ASSIGNMENT (( #62647 ) ) ; +#70265 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70267 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#70268 = PLANE ( 'NONE', #83222 ) ; +#70269 = ORIENTED_EDGE ( 'NONE', *, *, #73378, .T. ) ; +#70270 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70271 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70272 = ORIENTED_EDGE ( 'NONE', *, *, #14644, .F. ) ; +#70273 = PRESENTATION_STYLE_ASSIGNMENT (( #77946 ) ) ; +#70274 = SURFACE_STYLE_FILL_AREA ( #7908 ) ; +#70275 = ORIENTED_EDGE ( 'NONE', *, *, #57582, .F. ) ; +#70276 = ORIENTED_EDGE ( 'NONE', *, *, #21418, .F. ) ; +#70277 = SURFACE_STYLE_FILL_AREA ( #8924 ) ; +#70279 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#70278 = CARTESIAN_POINT ( 'NONE', ( 1.049748415576440053, -1.475020827802409951, 0.8100000000000000533 ) ) ; +#70280 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#70281 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23006 ) ) ; +#70282 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57354 ), #52447 ) ; +#70283 = LINE ( 'NONE', #47313, #43345 ) ; +#70284 = SURFACE_SIDE_STYLE ('',( #85108 ) ) ; +#70285 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -2.100000000000000089, -0.02000000000005030046 ) ) ; +#70286 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100933 ) ; +#70287 = SURFACE_SIDE_STYLE ('',( #1365 ) ) ; +#70288 = LINE ( 'NONE', #341, #69806 ) ; +#70289 = STYLED_ITEM ( 'NONE', ( #66029 ), #86512 ) ; +#70290 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70291 = ORIENTED_EDGE ( 'NONE', *, *, #66946, .T. ) ; +#70292 = ADVANCED_FACE ( 'NONE', ( #32246 ), #61399, .T. ) ; +#70294 = PRESENTATION_STYLE_ASSIGNMENT (( #75104 ) ) ; +#70293 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 3.570070999999999550, 0.8991599999999999593 ) ) ; +#70296 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70295 = VECTOR ( 'NONE', #19944, 1000.000000000000000 ) ; +#70297 = PRESENTATION_STYLE_ASSIGNMENT (( #63680 ) ) ; +#70298 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33691 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11945, #81526, #81008 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70299 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#70300 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70301 = FACE_OUTER_BOUND ( 'NONE', #90486, .T. ) ; +#70302 = FILL_AREA_STYLE_COLOUR ( '', #66449 ) ; +#70303 = EDGE_CURVE ( 'NONE', #59157, #86856, #38888, .T. ) ; +#70304 = ORIENTED_EDGE ( 'NONE', *, *, #15237, .F. ) ; +#70305 = STYLED_ITEM ( 'NONE', ( #2347 ), #7132 ) ; +#70306 = SURFACE_SIDE_STYLE ('',( #56031 ) ) ; +#70307 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70308 = LINE ( 'NONE', #31517, #18453 ) ; +#70309 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#70310 = CARTESIAN_POINT ( 'NONE', ( 4.557638500499999523, 6.264148499500000078, 0.8991599999999999593 ) ) ; +#70311 = AXIS2_PLACEMENT_3D ( 'NONE', #59090, #28907, #90700 ) ; +#70312 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8648700000000000276 ) ) ; +#70313 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70314 = FILL_AREA_STYLE ('',( #29990 ) ) ; +#70315 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#70316 = SURFACE_STYLE_FILL_AREA ( #32033 ) ; +#70317 = SURFACE_STYLE_USAGE ( .BOTH. , #45796 ) ; +#70318 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68487 ), #65433 ) ; +#70319 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#70320 = SURFACE_SIDE_STYLE ('',( #15150 ) ) ; +#70321 = SURFACE_STYLE_FILL_AREA ( #61688 ) ; +#70322 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70323 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39342 ), #27944 ) ; +#70324 = SURFACE_STYLE_FILL_AREA ( #23375 ) ; +#70325 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70326 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70327 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000971, -0.2400000000000000189 ) ) ; +#70328 = ORIENTED_EDGE ( 'NONE', *, *, #47134, .T. ) ; +#70329 = ADVANCED_FACE ( 'NONE', ( #84829 ), #93469, .T. ) ; +#70330 = SURFACE_STYLE_FILL_AREA ( #22360 ) ; +#70331 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#70332 = SURFACE_STYLE_FILL_AREA ( #79023 ) ; +#70333 = CARTESIAN_POINT ( 'NONE', ( 1.095384834513976502, -1.117969024486349827, 0.8099999999999157874 ) ) ; +#70334 = VECTOR ( 'NONE', #49187, 1000.000000000000000 ) ; +#70335 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70336 = PLANE ( 'NONE', #10726 ) ; +#70337 = ORIENTED_EDGE ( 'NONE', *, *, #62669, .F. ) ; +#70338 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70339 = CIRCLE ( 'NONE', #21444, 1.319494367338009955 ) ; +#70340 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70341 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70342 = ORIENTED_EDGE ( 'NONE', *, *, #33619, .F. ) ; +#70343 = ORIENTED_EDGE ( 'NONE', *, *, #63075, .F. ) ; +#70344 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70345 = VECTOR ( 'NONE', #45839, 1000.000000000000114 ) ; +#70346 = FILL_AREA_STYLE ('',( #24441 ) ) ; +#70347 = ORIENTED_EDGE ( 'NONE', *, *, #26927, .T. ) ; +#70348 = CARTESIAN_POINT ( 'NONE', ( -0.7453505133853431941, 1.552609075926967286, 0.8100000000000001643 ) ) ; +#70349 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70350 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53412 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71822, #42195, #34548 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70351 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39388 ) ) ; +#70353 = SHAPE_DEFINITION_REPRESENTATION ( #4970, #18831 ) ; +#70354 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#70356 = ORIENTED_EDGE ( 'NONE', *, *, #33391, .T. ) ; +#70355 = EDGE_LOOP ( 'NONE', ( #8074, #95337, #63625, #80712 ) ) ; +#70357 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #44181 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #28446 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#70358 = STYLED_ITEM ( 'NONE', ( #2503 ), #58520 ) ; +#70359 = VECTOR ( 'NONE', #80491, 1000.000000000000000 ) ; +#70360 = ORIENTED_EDGE ( 'NONE', *, *, #2115, .T. ) ; +#70361 = EDGE_CURVE ( 'NONE', #28590, #312, #94298, .T. ) ; +#70362 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59692, 'distance_accuracy_value', 'NONE'); +#70363 = FACE_OUTER_BOUND ( 'NONE', #20941, .T. ) ; +#70365 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.350000000000000089, 0.000000000000000000 ) ) ; +#70364 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#70366 = ORIENTED_EDGE ( 'NONE', *, *, #60272, .F. ) ; +#70367 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16571 ), #73678 ) ; +#70368 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70369 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70371 = PRESENTATION_STYLE_ASSIGNMENT (( #432 ) ) ; +#70370 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70372 = AXIS2_PLACEMENT_3D ( 'NONE', #60694, #69289, #76993 ) ; +#70373 = EDGE_LOOP ( 'NONE', ( #41155, #24080, #15190, #52341 ) ) ; +#70374 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 3.500000000000000444, 0.000000000000000000 ) ) ; +#70375 = ORIENTED_EDGE ( 'NONE', *, *, #42670, .T. ) ; +#70376 = EDGE_LOOP ( 'NONE', ( #87700, #13755, #50075, #5893 ) ) ; +#70377 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70378 = EDGE_CURVE ( 'NONE', #52472, #86070, #9172, .T. ) ; +#70379 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, 0.000000000000000000 ) ) ; +#70380 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#70381 = FACE_OUTER_BOUND ( 'NONE', #14311, .T. ) ; +#70382 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88600, #84454, #99666 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70384 = ORIENTED_EDGE ( 'NONE', *, *, #82716, .T. ) ; +#70383 = FILL_AREA_STYLE ('',( #21926 ) ) ; +#70385 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70387 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70388 = ORIENTED_EDGE ( 'NONE', *, *, #64022, .F. ) ; +#70389 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8814, #63559, #79878, #94130 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70391 = LINE ( 'NONE', #451, #100613 ) ; +#70390 = FACE_OUTER_BOUND ( 'NONE', #86794, .T. ) ; +#70392 = SURFACE_STYLE_USAGE ( .BOTH. , #46394 ) ; +#70394 = ORIENTED_EDGE ( 'NONE', *, *, #62149, .T. ) ; +#70393 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22490 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13911, #66584, #13390 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70395 = ORIENTED_EDGE ( 'NONE', *, *, #81394, .F. ) ; +#70397 = LINE ( 'NONE', #14735, #76369 ) ; +#70396 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70398 = FILL_AREA_STYLE_COLOUR ( '', #17065 ) ; +#70399 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70400 = VECTOR ( 'NONE', #45987, 1000.000000000000000 ) ; +#70401 = SURFACE_STYLE_USAGE ( .BOTH. , #56651 ) ; +#70402 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#70403 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2530, 'distance_accuracy_value', 'NONE'); +#70404 = EDGE_CURVE ( 'NONE', #99914, #59512, #49589, .T. ) ; +#70405 = CARTESIAN_POINT ( 'NONE', ( 0.2602179779670369952, -0.9240726320973919883, 0.8300000000000020695 ) ) ; +#70406 = ORIENTED_EDGE ( 'NONE', *, *, #72684, .F. ) ; +#70407 = CARTESIAN_POINT ( 'NONE', ( 0.07873568626789680114, -1.258231835375339891, 0.8100000000000000533 ) ) ; +#70408 = EDGE_LOOP ( 'NONE', ( #29344, #68701, #76128, #88217, #5611, #11395 ) ) ; +#70409 = CARTESIAN_POINT ( 'NONE', ( -0.4705492818410410005, -1.002707786929728728, 0.8299999999999997380 ) ) ; +#70410 = FACE_OUTER_BOUND ( 'NONE', #56687, .T. ) ; +#70411 = FACE_OUTER_BOUND ( 'NONE', #17886, .T. ) ; +#70412 = CARTESIAN_POINT ( 'NONE', ( 1.715925389647680044, -0.9637996098261990552, 0.8100000000000000533 ) ) ; +#70413 = FACE_OUTER_BOUND ( 'NONE', #67468, .T. ) ; +#70414 = EDGE_CURVE ( 'NONE', #98998, #80630, #94992, .T. ) ; +#70415 = PLANE ( 'NONE', #67840 ) ; +#70416 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70417 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#70418 = LINE ( 'NONE', #29248, #34074 ) ; +#70419 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#70420 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57423 ) ) ; +#70421 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70422 = FILL_AREA_STYLE ('',( #67041 ) ) ; +#70423 = FILL_AREA_STYLE ('',( #53126 ) ) ; +#70424 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#70425 = SURFACE_STYLE_FILL_AREA ( #87270 ) ; +#70426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76893 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40044, #95637, #1223 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70427 = STYLED_ITEM ( 'NONE', ( #14033 ), #96196 ) ; +#70428 = PLANE ( 'NONE', #26065 ) ; +#70429 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70430 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62309 ) ) ; +#70431 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#70432 = SURFACE_SIDE_STYLE ('',( #87277 ) ) ; +#70433 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54131 ) ) ; +#70434 = ORIENTED_EDGE ( 'NONE', *, *, #75778, .F. ) ; +#70435 = FACE_OUTER_BOUND ( 'NONE', #3705, .T. ) ; +#70436 = PRESENTATION_STYLE_ASSIGNMENT (( #32679 ) ) ; +#70437 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70438 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46310, 'distance_accuracy_value', 'NONE'); +#70439 = ORIENTED_EDGE ( 'NONE', *, *, #84092, .F. ) ; +#70440 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12992, 'distance_accuracy_value', 'NONE'); +#70441 = ADVANCED_FACE ( 'NONE', ( #64389 ), #26608, .F. ) ; +#70442 = PRESENTATION_STYLE_ASSIGNMENT (( #56174 ) ) ; +#70443 = LINE ( 'NONE', #15809, #85982 ) ; +#70444 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#70445 = FILL_AREA_STYLE ('',( #46965 ) ) ; +#70446 = CARTESIAN_POINT ( 'NONE', ( 9.974076750250087997, 8.979438249749913226, 0.8648700000000000276 ) ) ; +#70447 = STYLED_ITEM ( 'NONE', ( #35097 ), #66648 ) ; +#70448 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70449 = SURFACE_SIDE_STYLE ('',( #94432 ) ) ; +#70450 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #47953, #38032, #52363, #12961 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70451 = ORIENTED_EDGE ( 'NONE', *, *, #72322, .T. ) ; +#70452 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70453 = ORIENTED_EDGE ( 'NONE', *, *, #13946, .T. ) ; +#70455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20231, 'distance_accuracy_value', 'NONE'); +#70454 = AXIS2_PLACEMENT_3D ( 'NONE', #20537, #60397, #67008 ) ; +#70456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76214, 'distance_accuracy_value', 'NONE'); +#70457 = SURFACE_SIDE_STYLE ('',( #45436 ) ) ; +#70458 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70459 = LINE ( 'NONE', #95437, #34771 ) ; +#70460 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70461 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70462 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70463 = FILL_AREA_STYLE ('',( #85283 ) ) ; +#70464 = AXIS2_PLACEMENT_3D ( 'NONE', #41493, #79798, #88443 ) ; +#70465 = ORIENTED_EDGE ( 'NONE', *, *, #100328, .T. ) ; +#70466 = EDGE_CURVE ( 'NONE', #51695, #42002, #10155, .T. ) ; +#70467 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70468 = EDGE_CURVE ( 'NONE', #3141, #58587, #56762, .T. ) ; +#70469 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70470 = EDGE_LOOP ( 'NONE', ( #23931, #70625, #43427, #42188 ) ) ; +#70471 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89929 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82416, #67064, #23625 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70472 = SURFACE_STYLE_FILL_AREA ( #61843 ) ; +#70473 = ORIENTED_EDGE ( 'NONE', *, *, #63697, .F. ) ; +#70474 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#70475 = CARTESIAN_POINT ( 'NONE', ( 1.130331698131229912, -1.432449005990829916, 0.8100000000000000533 ) ) ; +#70476 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70477 = FILL_AREA_STYLE ('',( #78164 ) ) ; +#70478 = SURFACE_STYLE_FILL_AREA ( #98046 ) ; +#70479 = CARTESIAN_POINT ( 'NONE', ( 1.799202792133490103, -1.182875588085640306, 0.8100000000000000533 ) ) ; +#70480 = FILL_AREA_STYLE_COLOUR ( '', #12950 ) ; +#70481 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#70483 = ORIENTED_EDGE ( 'NONE', *, *, #65737, .F. ) ; +#70482 = VERTEX_POINT ( 'NONE', #87864 ) ; +#70484 = STYLED_ITEM ( 'NONE', ( #72899 ), #81956 ) ; +#70485 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75380 ) ) ; +#70486 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70487 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#70488 = ORIENTED_EDGE ( 'NONE', *, *, #1945, .T. ) ; +#70489 = EDGE_CURVE ( 'NONE', #34980, #44992, #40927, .T. ) ; +#70490 = FILL_AREA_STYLE_COLOUR ( '', #96563 ) ; +#70491 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70492 = STYLED_ITEM ( 'NONE', ( #59945 ), #35594 ) ; +#70493 = SURFACE_STYLE_USAGE ( .BOTH. , #39345 ) ; +#70494 = ORIENTED_EDGE ( 'NONE', *, *, #49290, .F. ) ; +#70495 = VERTEX_POINT ( 'NONE', #32751 ) ; +#70496 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70497 = SURFACE_STYLE_USAGE ( .BOTH. , #91967 ) ; +#70498 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49550 ) ) ; +#70499 = STYLED_ITEM ( 'NONE', ( #80383 ), #18746 ) ; +#70500 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60693 ) ) ; +#70501 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#70502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70503 = PLANE ( 'NONE', #17217 ) ; +#70504 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#70505 = ORIENTED_EDGE ( 'NONE', *, *, #35696, .T. ) ; +#70506 = ORIENTED_EDGE ( 'NONE', *, *, #43658, .F. ) ; +#70507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70508 = VECTOR ( 'NONE', #2118, 1000.000000000000000 ) ; +#70509 = ORIENTED_EDGE ( 'NONE', *, *, #77367, .T. ) ; +#70510 = AXIS2_PLACEMENT_3D ( 'NONE', #82757, #43438, #18944 ) ; +#70511 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51273 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22119, #68566, #61956 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70512 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70513 = EDGE_CURVE ( 'NONE', #54388, #15767, #56252, .T. ) ; +#70514 = VECTOR ( 'NONE', #90573, 1000.000000000000000 ) ; +#70516 = ORIENTED_EDGE ( 'NONE', *, *, #15009, .T. ) ; +#70515 = PLANE ( 'NONE', #24942 ) ; +#70517 = SURFACE_SIDE_STYLE ('',( #14340 ) ) ; +#70518 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70519 = SURFACE_SIDE_STYLE ('',( #40924 ) ) ; +#70520 = VERTEX_POINT ( 'NONE', #95997 ) ; +#70521 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -4.344024262657780003E-34 ) ) ; +#70522 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70523 = ORIENTED_EDGE ( 'NONE', *, *, #73562, .F. ) ; +#70524 = STYLED_ITEM ( 'NONE', ( #49994 ), #7946 ) ; +#70525 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70526 = VECTOR ( 'NONE', #10469, 1000.000000000000000 ) ; +#70527 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70529 = ORIENTED_EDGE ( 'NONE', *, *, #69979, .T. ) ; +#70528 = FILL_AREA_STYLE_COLOUR ( '', #15068 ) ; +#70530 = FILL_AREA_STYLE_COLOUR ( '', #52540 ) ; +#70531 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.000000000000000000, 1.149999999999999911 ) ) ; +#70532 = VECTOR ( 'NONE', #97070, 1000.000000000000000 ) ; +#70533 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#70534 = EDGE_CURVE ( 'NONE', #89669, #63990, #67256, .T. ) ; +#70535 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70536 = CARTESIAN_POINT ( 'NONE', ( 1.809085324296979991, -1.273483528256009967, 0.8099999999999996092 ) ) ; +#70537 = ORIENTED_EDGE ( 'NONE', *, *, #12413, .F. ) ; +#70538 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #421 ), #72159 ) ; +#70539 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.40000000000000036 ) ) ; +#70540 = FACE_OUTER_BOUND ( 'NONE', #40185, .T. ) ; +#70541 = STYLED_ITEM ( 'NONE', ( #84784 ), #52769 ) ; +#70543 = CARTESIAN_POINT ( 'NONE', ( 1.566431021886530051, -1.318798174699070014, 0.8299999999999999600 ) ) ; +#70542 = CARTESIAN_POINT ( 'NONE', ( -0.8560791624706871605, 0.5647286298174479802, 0.8100000000000000533 ) ) ; +#70544 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1238200612200849871, 0.000000000000000000 ) ) ; +#70545 = EDGE_CURVE ( 'NONE', #34736, #49420, #6044, .T. ) ; +#70546 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#70547 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71353, #40230, #34975, #9498, #11866, #95303, #35977, #82432, #40738 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999975020, 0.3749999999999978351, 0.4999999999999982236, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70548 = VECTOR ( 'NONE', #53253, 1000.000000000000000 ) ; +#70549 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91745 ), #31421 ) ; +#70550 = LINE ( 'NONE', #16394, #80107 ) ; +#70551 = ORIENTED_EDGE ( 'NONE', *, *, #24754, .F. ) ; +#70552 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70553 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70554 = CARTESIAN_POINT ( 'NONE', ( -4.606914704940411312E-28, 0.2799999999751889845, 0.2000000000066392836 ) ) ; +#70555 = ORIENTED_EDGE ( 'NONE', *, *, #56522, .F. ) ; +#70556 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000003147, 0.4000000000000000222 ) ) ; +#70558 = SURFACE_STYLE_FILL_AREA ( #80769 ) ; +#70557 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31487, #45756, #93725 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70559 = FILL_AREA_STYLE_COLOUR ( '', #2791 ) ; +#70560 = AXIS2_PLACEMENT_3D ( 'NONE', #41706, #87154, #17176 ) ; +#70561 = ORIENTED_EDGE ( 'NONE', *, *, #12054, .T. ) ; +#70562 = CARTESIAN_POINT ( 'NONE', ( 1.877470194538120030, -1.043958301690999901, 0.8100000000000008304 ) ) ; +#70563 = FACE_OUTER_BOUND ( 'NONE', #32355, .T. ) ; +#70564 = CARTESIAN_POINT ( 'NONE', ( -0.007915629041866760474, -1.066767002799750008, 0.8300000000000005151 ) ) ; +#70565 = SURFACE_SIDE_STYLE ('',( #23124 ) ) ; +#70566 = SURFACE_SIDE_STYLE ('',( #56303 ) ) ; +#70567 = VECTOR ( 'NONE', #25948, 1000.000000000000000 ) ; +#70568 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70569 = VECTOR ( 'NONE', #46028, 1000.000000000000000 ) ; +#70570 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37931 ), #57579 ) ; +#70571 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#70572 = SURFACE_STYLE_FILL_AREA ( #47605 ) ; +#70574 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70573 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13439 ) ) ; +#70575 = EDGE_CURVE ( 'NONE', #100148, #30033, #60276, .T. ) ; +#70576 = ADVANCED_FACE ( 'NONE', ( #82723 ), #19929, .T. ) ; +#70578 = VECTOR ( 'NONE', #15820, 1000.000000000000000 ) ; +#70577 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70579 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90087, 'distance_accuracy_value', 'NONE'); +#70580 = SURFACE_STYLE_USAGE ( .BOTH. , #72596 ) ; +#70581 = EDGE_LOOP ( 'NONE', ( #50755, #38507, #971, #1720 ) ) ; +#70582 = SURFACE_SIDE_STYLE ('',( #46587 ) ) ; +#70584 = ORIENTED_EDGE ( 'NONE', *, *, #46023, .T. ) ; +#70583 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37505 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51708, #52698, #27732 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70585 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#70586 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79827, 'distance_accuracy_value', 'NONE'); +#70587 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42049, 'distance_accuracy_value', 'NONE'); +#70588 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70589 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#70590 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -11.27000000000000135 ) ) ; +#70591 = LINE ( 'NONE', #24678, #63566 ) ; +#70592 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30392 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76048, #12694, #35777 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70593 = SURFACE_SIDE_STYLE ('',( #71621 ) ) ; +#70594 = CARTESIAN_POINT ( 'NONE', ( 0.01897074359908140079, -1.165682221622120096, 0.8100000000000000533 ) ) ; +#70595 = LINE ( 'NONE', #84903, #89621 ) ; +#70596 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#70597 = ORIENTED_EDGE ( 'NONE', *, *, #99366, .T. ) ; +#70598 = ADVANCED_FACE ( 'NONE', ( #36764 ), #66396, .T. ) ; +#70599 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76286, 'distance_accuracy_value', 'NONE'); +#70601 = EDGE_CURVE ( 'NONE', #919, #13962, #4107, .T. ) ; +#70602 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70603 = ORIENTED_EDGE ( 'NONE', *, *, #68786, .T. ) ; +#70604 = VERTEX_POINT ( 'NONE', #51612 ) ; +#70605 = PRESENTATION_STYLE_ASSIGNMENT (( #61472 ) ) ; +#70606 = EDGE_CURVE ( 'NONE', #34647, #24100, #59285, .T. ) ; +#70607 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#70608 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70609 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#70610 = ORIENTED_EDGE ( 'NONE', *, *, #53754, .F. ) ; +#70611 = CYLINDRICAL_SURFACE ( 'NONE', #91372, 0.009999999999999998473 ) ; +#70612 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70613 = EDGE_CURVE ( 'NONE', #5198, #10501, #43909, .T. ) ; +#70614 = PLANE ( 'NONE', #67136 ) ; +#70615 = VECTOR ( 'NONE', #80186, 1000.000000000000000 ) ; +#70616 = SURFACE_STYLE_USAGE ( .BOTH. , #21765 ) ; +#70617 = ORIENTED_EDGE ( 'NONE', *, *, #52544, .F. ) ; +#70618 = EDGE_CURVE ( 'NONE', #25891, #93833, #21934, .T. ) ; +#70619 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70620 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56012 ), #16804 ) ; +#70621 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#70622 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70623 = SURFACE_SIDE_STYLE ('',( #56369 ) ) ; +#70624 = VERTEX_POINT ( 'NONE', #31606 ) ; +#70625 = ORIENTED_EDGE ( 'NONE', *, *, #98772, .F. ) ; +#70626 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70627 = STYLED_ITEM ( 'NONE', ( #42873 ), #47260 ) ; +#70628 = VECTOR ( 'NONE', #64476, 1000.000000000000000 ) ; +#70629 = ORIENTED_EDGE ( 'NONE', *, *, #30544, .F. ) ; +#70630 = ADVANCED_FACE ( 'NONE', ( #85717 ), #16247, .T. ) ; +#70631 = EDGE_CURVE ( 'NONE', #6703, #46008, #99926, .T. ) ; +#70632 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85272 ), #31498 ) ; +#70633 = VERTEX_POINT ( 'NONE', #22430 ) ; +#70634 = ORIENTED_EDGE ( 'NONE', *, *, #60847, .T. ) ; +#70635 = ADVANCED_FACE ( 'NONE', ( #30077 ), #86224, .T. ) ; +#70636 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#70639 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#70638 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#70637 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62278 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17058, #80391, #26271 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70640 = STYLED_ITEM ( 'NONE', ( #85767 ), #36135 ) ; +#70641 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70642 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70643 = ORIENTED_EDGE ( 'NONE', *, *, #25187, .T. ) ; +#70644 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70645 = ORIENTED_EDGE ( 'NONE', *, *, #74538, .F. ) ; +#70646 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #90609 ) ) ; +#70647 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70648 = LINE ( 'NONE', #55858, #20615 ) ; +#70649 = VERTEX_POINT ( 'NONE', #84228 ) ; +#70650 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000002220, -3.266666666666653285, 0.000000000000000000 ) ) ; +#70651 = VERTEX_POINT ( 'NONE', #14219 ) ; +#70652 = VECTOR ( 'NONE', #97275, 1000.000000000000000 ) ; +#70653 = STYLED_ITEM ( 'NONE', ( #78632 ), #96803 ) ; +#70655 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70654 = SURFACE_STYLE_FILL_AREA ( #46133 ) ; +#70656 = ADVANCED_FACE ( 'NONE', ( #45380 ), #45872, .F. ) ; +#70657 = SURFACE_STYLE_FILL_AREA ( #39517 ) ; +#70658 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85303 ) ) ; +#70659 = LINE ( 'NONE', #16012, #76090 ) ; +#70660 = STYLED_ITEM ( 'NONE', ( #73437 ), #11495 ) ; +#70661 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#70662 = ORIENTED_EDGE ( 'NONE', *, *, #62431, .F. ) ; +#70664 = FILL_AREA_STYLE ('',( #8793 ) ) ; +#70663 = PRESENTATION_STYLE_ASSIGNMENT (( #54875 ) ) ; +#70665 = FILL_AREA_STYLE_COLOUR ( '', #87754 ) ; +#70666 = EDGE_CURVE ( 'NONE', #98291, #89578, #38273, .T. ) ; +#70667 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70668 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41491, 'distance_accuracy_value', 'NONE'); +#70669 = STYLED_ITEM ( 'NONE', ( #72627 ), #67457 ) ; +#70671 = ADVANCED_FACE ( 'NONE', ( #41306 ), #81119, .T. ) ; +#70670 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70672 = FACE_OUTER_BOUND ( 'NONE', #6102, .T. ) ; +#70673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70674 = SURFACE_STYLE_FILL_AREA ( #64038 ) ; +#70675 = SURFACE_SIDE_STYLE ('',( #1229 ) ) ; +#70676 = VERTEX_POINT ( 'NONE', #56641 ) ; +#70677 = CARTESIAN_POINT ( 'NONE', ( -1.000284964254319897, -1.196758459236680006, 0.8300000000000002931 ) ) ; +#70678 = PRESENTATION_STYLE_ASSIGNMENT (( #2765 ) ) ; +#70679 = EDGE_CURVE ( 'NONE', #25673, #79525, #95369, .T. ) ; +#70680 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34864 ) ) ; +#70681 = FACE_BOUND ( 'NONE', #84455, .T. ) ; +#70682 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#70683 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#70684 = CYLINDRICAL_SURFACE ( 'NONE', #69137, 0.05000000000000012768 ) ; +#70685 = SURFACE_STYLE_FILL_AREA ( #19470 ) ; +#70686 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70687 = AXIS2_PLACEMENT_3D ( 'NONE', #1707, #16456, #15971 ) ; +#70688 = VERTEX_POINT ( 'NONE', #34654 ) ; +#70689 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220085265, 2.499999999999999556, 0.000000000000000000 ) ) ; +#70690 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70691 = SURFACE_STYLE_USAGE ( .BOTH. , #32912 ) ; +#70692 = VECTOR ( 'NONE', #9820, 1000.000000000000227 ) ; +#70693 = FACE_OUTER_BOUND ( 'NONE', #99571, .T. ) ; +#70694 = LINE ( 'NONE', #31902, #43244 ) ; +#70695 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#70696 = LINE ( 'NONE', #63070, #8134 ) ; +#70697 = FACE_OUTER_BOUND ( 'NONE', #55687, .T. ) ; +#70698 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70699 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28367 ) ) ; +#70700 = FACE_OUTER_BOUND ( 'NONE', #55118, .T. ) ; +#70701 = ADVANCED_FACE ( 'NONE', ( #25483 ), #71423, .T. ) ; +#70702 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70703 = FILL_AREA_STYLE_COLOUR ( '', #87693 ) ; +#70704 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#70705 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#70706 = EDGE_LOOP ( 'NONE', ( #8423, #13800, #85552, #24859, #59010, #28700 ) ) ; +#70707 = FACE_OUTER_BOUND ( 'NONE', #51440, .T. ) ; +#70708 = ORIENTED_EDGE ( 'NONE', *, *, #88639, .F. ) ; +#70709 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15194, 'distance_accuracy_value', 'NONE'); +#70710 = CYLINDRICAL_SURFACE ( 'NONE', #16373, 0.009999999999999998473 ) ; +#70711 = PRESENTATION_STYLE_ASSIGNMENT (( #9361 ) ) ; +#70712 = CARTESIAN_POINT ( 'NONE', ( 0.3050025479630040226, -1.260362508506799983, 0.8299999999999999600 ) ) ; +#70713 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70714 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#70715 = LINE ( 'NONE', #93652, #29203 ) ; +#70716 = AXIS2_PLACEMENT_3D ( 'NONE', #2407, #24398, #87663 ) ; +#70717 = CARTESIAN_POINT ( 'NONE', ( -1.102470388999849948, -1.163804091156239950, 0.8100000000000000533 ) ) ; +#70718 = EDGE_LOOP ( 'NONE', ( #84318, #30972, #8294, #55855 ) ) ; +#70719 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65241, 'distance_accuracy_value', 'NONE'); +#70720 = EDGE_CURVE ( 'NONE', #3632, #94835, #27432, .T. ) ; +#70723 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30340 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65167, #33020, #48862 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70722 = STYLED_ITEM ( 'NONE', ( #60867 ), #38040 ) ; +#70721 = SURFACE_STYLE_USAGE ( .BOTH. , #30911 ) ; +#70724 = CIRCLE ( 'NONE', #5447, 1.874993856093760236 ) ; +#70725 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57727 ), #34828 ) ; +#70726 = LINE ( 'NONE', #93658, #47014 ) ; +#70727 = ORIENTED_EDGE ( 'NONE', *, *, #41998, .T. ) ; +#70728 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70729 = EDGE_CURVE ( 'NONE', #88429, #30563, #90251, .T. ) ; +#70730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60460 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12662, #90330, #27570 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70731 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70732 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57736 ) ) ; +#70733 = PRESENTATION_STYLE_ASSIGNMENT (( #31938 ) ) ; +#70734 = FILL_AREA_STYLE_COLOUR ( '', #68374 ) ; +#70735 = DIRECTION ( 'NONE', ( -0.7071060119555145906, 0.7071075504167435577, 0.000000000000000000 ) ) ; +#70736 = ORIENTED_EDGE ( 'NONE', *, *, #38583, .F. ) ; +#70737 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8099999999999442091 ) ) ; +#70738 = STYLED_ITEM ( 'NONE', ( #94005 ), #9657 ) ; +#70739 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#70740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50482, 'distance_accuracy_value', 'NONE'); +#70741 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #612 ), #10298 ) ; +#70742 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#70743 = FACE_OUTER_BOUND ( 'NONE', #29106, .T. ) ; +#70744 = VERTEX_POINT ( 'NONE', #44273 ) ; +#70745 = FACE_OUTER_BOUND ( 'NONE', #43278, .T. ) ; +#70746 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#70747 = AXIS2_PLACEMENT_3D ( 'NONE', #96460, #41386, #40886 ) ; +#70748 = ORIENTED_EDGE ( 'NONE', *, *, #64972, .T. ) ; +#70749 = CARTESIAN_POINT ( 'NONE', ( -0.03276632349404259847, -1.496872818153279994, 0.8100000000000000533 ) ) ; +#70750 = CARTESIAN_POINT ( 'NONE', ( -0.1311282467532469964, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#70751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70752 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46449 ) ) ; +#70753 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #15617, #33701 ) ; +#70754 = CARTESIAN_POINT ( 'NONE', ( 0.2603867800980460001, -1.020295711170670083, 0.8100000000000000533 ) ) ; +#70755 = EDGE_CURVE ( 'NONE', #2486, #12539, #60805, .T. ) ; +#70756 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34091 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74076, #34298, #42925 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70757 = ORIENTED_EDGE ( 'NONE', *, *, #9880, .T. ) ; +#70758 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70760 = LINE ( 'NONE', #78926, #15458 ) ; +#70759 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70761 = ORIENTED_EDGE ( 'NONE', *, *, #18769, .F. ) ; +#70762 = LINE ( 'NONE', #816, #45018 ) ; +#70763 = SURFACE_STYLE_FILL_AREA ( #39629 ) ; +#70764 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22655 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80146, #24526, #70421 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70765 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95155 ), #83831 ) ; +#70766 = LINE ( 'NONE', #78431, #33556 ) ; +#70767 = ORIENTED_EDGE ( 'NONE', *, *, #80286, .T. ) ; +#70768 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70769 = VECTOR ( 'NONE', #74247, 1000.000000000000000 ) ; +#70770 = ORIENTED_EDGE ( 'NONE', *, *, #91649, .T. ) ; +#70771 = ORIENTED_EDGE ( 'NONE', *, *, #33863, .T. ) ; +#70772 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70773 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#70774 = EDGE_CURVE ( 'NONE', #36856, #89439, #5934, .T. ) ; +#70775 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70776 = ORIENTED_EDGE ( 'NONE', *, *, #74652, .T. ) ; +#70777 = FACE_OUTER_BOUND ( 'NONE', #91437, .T. ) ; +#70778 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70779 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#70780 = STYLED_ITEM ( 'NONE', ( #32559 ), #19976 ) ; +#70781 = EDGE_LOOP ( 'NONE', ( #26697, #25588, #86222, #34000 ) ) ; +#70783 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70782 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70784 = PRESENTATION_STYLE_ASSIGNMENT (( #41177 ) ) ; +#70785 = ORIENTED_EDGE ( 'NONE', *, *, #31981, .T. ) ; +#70786 = ORIENTED_EDGE ( 'NONE', *, *, #24548, .T. ) ; +#70787 = FILL_AREA_STYLE_COLOUR ( '', #14335 ) ; +#70788 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85990 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4282, #73248, #51266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70789 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #53780, #85419, #148, #22127 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70790 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#70791 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#70792 = ADVANCED_FACE ( 'NONE', ( #28969 ), #11559, .T. ) ; +#70793 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#70794 = AXIS2_PLACEMENT_3D ( 'NONE', #64367, #81221, #64867 ) ; +#70795 = AXIS2_PLACEMENT_3D ( 'NONE', #77091, #23489, #43551 ) ; +#70796 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#70797 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70798 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000222, 0.000000000000000000 ) ) ; +#70799 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70800 = VECTOR ( 'NONE', #11259, 1000.000000000000000 ) ; +#70801 = FILL_AREA_STYLE ('',( #17163 ) ) ; +#70802 = VERTEX_POINT ( 'NONE', #27489 ) ; +#70803 = SURFACE_SIDE_STYLE ('',( #8424 ) ) ; +#70804 = EDGE_CURVE ( 'NONE', #42493, #27316, #12065, .T. ) ; +#70805 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70806 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70807 = STYLED_ITEM ( 'NONE', ( #75053 ), #3179 ) ; +#70808 = PRESENTATION_STYLE_ASSIGNMENT (( #1375 ) ) ; +#70809 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44695 ) ) ; +#70810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70811 = CARTESIAN_POINT ( 'NONE', ( -0.1525528712910690365, -1.164063370418184196, 0.8166666666666667629 ) ) ; +#70812 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#70813 = EDGE_CURVE ( 'NONE', #75732, #69635, #74452, .T. ) ; +#70814 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000001110, 0.6500000000000001332 ) ) ; +#70815 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999667, -3.009265538105054994E-33 ) ) ; +#70816 = ORIENTED_EDGE ( 'NONE', *, *, #9658, .F. ) ; +#70817 = LINE ( 'NONE', #41206, #55364 ) ; +#70818 = DIRECTION ( 'NONE', ( 0.7071067811865482389, -0.7071067811865469066, 0.000000000000000000 ) ) ; +#70819 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#70820 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, 0.000000000000000000 ) ) ; +#70821 = SURFACE_STYLE_USAGE ( .BOTH. , #17187 ) ; +#70822 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70823 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13684 ) ) ; +#70824 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42987, 'distance_accuracy_value', 'NONE'); +#70825 = PLANE ( 'NONE', #70716 ) ; +#70827 = EDGE_CURVE ( 'NONE', #9642, #52330, #68752, .T. ) ; +#70826 = FILL_AREA_STYLE_COLOUR ( '', #90728 ) ; +#70829 = ADVANCED_FACE ( 'NONE', ( #84597 ), #29475, .F. ) ; +#70828 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#70830 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70831 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33696, #65833, #64820, #88807, #26042, #50036, #87288, #48519, #71983, #81176, #57192, #47989, #73500, #63827, #40347, #94921, #1538, #87798, #79656 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.895499375637957961E-05, 3.738329657103353019E-05, 5.527352819117361014E-05, 7.271121307565384367E-05, 8.968733045764818097E-05, 0.0001061612447615800111, 0.0001221153084768700572, 0.0001378567193849246256, 0.0001535008571834084456, 0.0001692684803906427718, 0.0001854697664425767050, 0.0002020894132512589736, 0.0002193451494927706690, 0.0002374891443266025786, 0.0002566052952319190176, 0.0002770255913895567626 ), + .UNSPECIFIED. ) ; +#70832 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#70833 = PRESENTATION_STYLE_ASSIGNMENT (( #69804 ) ) ; +#70834 = STYLED_ITEM ( 'NONE', ( #46801 ), #71429 ) ; +#70835 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#70836 = EDGE_CURVE ( 'NONE', #12278, #66504, #37650, .T. ) ; +#70837 = EDGE_CURVE ( 'NONE', #24251, #47168, #76947, .T. ) ; +#70838 = PRESENTATION_STYLE_ASSIGNMENT (( #8455 ) ) ; +#70839 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70840 = VECTOR ( 'NONE', #83161, 1000.000000000000114 ) ; +#70841 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70842 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62225, 'distance_accuracy_value', 'NONE'); +#70843 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#70844 = LINE ( 'NONE', #31028, #94329 ) ; +#70845 = PRESENTATION_STYLE_ASSIGNMENT (( #100837 ) ) ; +#70846 = ORIENTED_EDGE ( 'NONE', *, *, #80650, .F. ) ; +#70847 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70848 = PLANE ( 'NONE', #2921 ) ; +#70849 = AXIS2_PLACEMENT_3D ( 'NONE', #99545, #37867, #22537 ) ; +#70850 = EDGE_CURVE ( 'NONE', #40797, #20259, #91736, .T. ) ; +#70852 = FILL_AREA_STYLE_COLOUR ( '', #49362 ) ; +#70851 = STYLED_ITEM ( 'NONE', ( #71840 ), #88626 ) ; +#70853 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62270, 'distance_accuracy_value', 'NONE'); +#70855 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#70854 = CARTESIAN_POINT ( 'NONE', ( -0.01180881832068430073, -1.255590633215009966, 0.8300000000000002931 ) ) ; +#70856 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70858 = STYLED_ITEM ( 'NONE', ( #12249 ), #47832 ) ; +#70857 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8100000000000074918 ) ) ; +#70859 = STYLED_ITEM ( 'NONE', ( #50237 ), #26761 ) ; +#70860 = EDGE_CURVE ( 'NONE', #84529, #61508, #100792, .T. ) ; +#70861 = SURFACE_STYLE_USAGE ( .BOTH. , #8473 ) ; +#70862 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23778 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95844, #62734, #72374 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70863 = VERTEX_POINT ( 'NONE', #52984 ) ; +#70864 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70865 = PRESENTATION_STYLE_ASSIGNMENT (( #80060 ) ) ; +#70866 = LINE ( 'NONE', #23394, #47124 ) ; +#70867 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51394, 'distance_accuracy_value', 'NONE'); +#70868 = AXIS2_PLACEMENT_3D ( 'NONE', #62796, #94887, #39272 ) ; +#70869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96868, 'distance_accuracy_value', 'NONE'); +#70870 = VECTOR ( 'NONE', #3286, 1000.000000000000000 ) ; +#70871 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70872 = ORIENTED_EDGE ( 'NONE', *, *, #47094, .F. ) ; +#70873 = VERTEX_POINT ( 'NONE', #22309 ) ; +#70874 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100691 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40802, #49460, #10539 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70875 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52639 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11970, #27392, #57058 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70876 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#70877 = ORIENTED_EDGE ( 'NONE', *, *, #81285, .T. ) ; +#70878 = CARTESIAN_POINT ( 'NONE', ( 0.3142305969234919782, -0.9692640729113169984, 0.8299999999999996270 ) ) ; +#70879 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70880 = PLANE ( 'NONE', #54917 ) ; +#70881 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#70882 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43171 ), #82342 ) ; +#70883 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70884 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #14261 ) ; +#70885 = FACE_OUTER_BOUND ( 'NONE', #94330, .T. ) ; +#70886 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70888 = ORIENTED_EDGE ( 'NONE', *, *, #90198, .T. ) ; +#70887 = ORIENTED_EDGE ( 'NONE', *, *, #67367, .T. ) ; +#70889 = EDGE_CURVE ( 'NONE', #67869, #38490, #53474, .T. ) ; +#70890 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#70891 = VERTEX_POINT ( 'NONE', #30439 ) ; +#70892 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#70893 = STYLED_ITEM ( 'NONE', ( #86878 ), #12155 ) ; +#70894 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#70896 = FACE_OUTER_BOUND ( 'NONE', #51963, .T. ) ; +#70895 = PRESENTATION_STYLE_ASSIGNMENT (( #941 ) ) ; +#70897 = ORIENTED_EDGE ( 'NONE', *, *, #92862, .T. ) ; +#70898 = ADVANCED_FACE ( 'NONE', ( #46780 ), #84101, .T. ) ; +#70899 = CARTESIAN_POINT ( 'NONE', ( 4.105090750249975606, 4.241822750249974128, 0.8648700000000000276 ) ) ; +#70900 = FACE_OUTER_BOUND ( 'NONE', #78748, .T. ) ; +#70901 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82357 ) ) ; +#70902 = EDGE_LOOP ( 'NONE', ( #29313, #78986, #47614, #94437 ) ) ; +#70904 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333326642, 0.6999999999999999556, 0.000000000000000000 ) ) ; +#70903 = PLANE ( 'NONE', #66039 ) ; +#70905 = ORIENTED_EDGE ( 'NONE', *, *, #20179, .F. ) ; +#70906 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#70907 = EDGE_LOOP ( 'NONE', ( #78554, #36839, #64648, #78160 ) ) ; +#70908 = ORIENTED_EDGE ( 'NONE', *, *, #76711, .F. ) ; +#70909 = FILL_AREA_STYLE ('',( #439 ) ) ; +#70910 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#70911 = ORIENTED_EDGE ( 'NONE', *, *, #35202, .F. ) ; +#70912 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#70913 = PRESENTATION_STYLE_ASSIGNMENT (( #78557 ) ) ; +#70914 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43118 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81440, #33962, #58964 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70915 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.266666666666653285, 3.495651678170078205E-76 ) ) ; +#70916 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90438 ) ) ; +#70917 = ORIENTED_EDGE ( 'NONE', *, *, #29053, .T. ) ; +#70919 = SURFACE_STYLE_FILL_AREA ( #93345 ) ; +#70918 = SURFACE_SIDE_STYLE ('',( #86739 ) ) ; +#70920 = EDGE_LOOP ( 'NONE', ( #63656, #85477, #60969, #62888 ) ) ; +#70921 = VERTEX_POINT ( 'NONE', #24362 ) ; +#70923 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6892893218813450629, 0.9757359312880711233 ) ) ; +#70922 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70924 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.8166667230436682745, 0.6665916835684375652 ) ) ; +#70925 = CARTESIAN_POINT ( 'NONE', ( 4.532300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#70926 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30151 ) ) ; +#70927 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70928 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32933 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63842, #5022, #89327 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#70929 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74210 ) ) ; +#70930 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#70931 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000002442, -3.383333333333326642, 0.000000000000000000 ) ) ; +#70932 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70933 = LINE ( 'NONE', #79617, #27989 ) ; +#70934 = ORIENTED_EDGE ( 'NONE', *, *, #30049, .F. ) ; +#70935 = CARTESIAN_POINT ( 'NONE', ( 6.084989124874956801, 10.26637212487495709, 0.8648700000000000276 ) ) ; +#70936 = AXIS2_PLACEMENT_3D ( 'NONE', #65995, #95587, #56852 ) ; +#70937 = PRESENTATION_STYLE_ASSIGNMENT (( #86241 ) ) ; +#70938 = ORIENTED_EDGE ( 'NONE', *, *, #74213, .T. ) ; +#70939 = PLANE ( 'NONE', #81530 ) ; +#70940 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#70941 = SURFACE_STYLE_USAGE ( .BOTH. , #64287 ) ; +#70942 = CARTESIAN_POINT ( 'NONE', ( 9.924579499499824209, 8.109696500500174210, 0.8991599999999999593 ) ) ; +#70944 = VECTOR ( 'NONE', #72994, 1000.000000000000000 ) ; +#70943 = CARTESIAN_POINT ( 'NONE', ( 1.762090253802699902, -0.9814610950457449690, 0.8100000000000000533 ) ) ; +#70945 = FILL_AREA_STYLE_COLOUR ( '', #67949 ) ; +#70946 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87058, 'distance_accuracy_value', 'NONE'); +#70947 = SURFACE_SIDE_STYLE ('',( #39801 ) ) ; +#70948 = AXIS2_PLACEMENT_3D ( 'NONE', #37884, #29217, #60394 ) ; +#70949 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.266666666666653285, 0.000000000000000000 ) ) ; +#70950 = SURFACE_SIDE_STYLE ('',( #25512 ) ) ; +#70951 = AXIS2_PLACEMENT_3D ( 'NONE', #90674, #5854, #76337 ) ; +#70952 = SURFACE_STYLE_USAGE ( .BOTH. , #64296 ) ; +#70953 = CARTESIAN_POINT ( 'NONE', ( -1.220268398896690032, -0.9623790331012080923, 0.8299999999999998490 ) ) ; +#70954 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70955 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 12.65647100000000158, 0.8648700000000000276 ) ) ; +#70956 = FACE_OUTER_BOUND ( 'NONE', #22590, .T. ) ; +#70957 = FILL_AREA_STYLE_COLOUR ( '', #9449 ) ; +#70958 = AXIS2_PLACEMENT_3D ( 'NONE', #25347, #1842, #3345 ) ; +#70959 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#70960 = EDGE_CURVE ( 'NONE', #55863, #60664, #10243, .T. ) ; +#70961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28540 ), #74250 ) ; +#70962 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18981, 'distance_accuracy_value', 'NONE'); +#70963 = VERTEX_POINT ( 'NONE', #94748 ) ; +#70964 = PLANE ( 'NONE', #316 ) ; +#70965 = FILL_AREA_STYLE ('',( #61814 ) ) ; +#70966 = ORIENTED_EDGE ( 'NONE', *, *, #19359, .T. ) ; +#70967 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#70968 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#70969 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#70970 = ADVANCED_FACE ( 'NONE', ( #96263 ), #95240, .F. ) ; +#70971 = STYLED_ITEM ( 'NONE', ( #57242 ), #68554 ) ; +#70972 = SURFACE_STYLE_FILL_AREA ( #80164 ) ; +#70973 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36954, #83423, #90571, #6712 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#70974 = VECTOR ( 'NONE', #58281, 1000.000000000000000 ) ; +#70975 = FILL_AREA_STYLE ('',( #62836 ) ) ; +#70976 = ADVANCED_FACE ( 'NONE', ( #26363 ), #2368, .T. ) ; +#70977 = VECTOR ( 'NONE', #54002, 1000.000000000000000 ) ; +#70978 = ORIENTED_EDGE ( 'NONE', *, *, #29864, .F. ) ; +#70979 = ORIENTED_EDGE ( 'NONE', *, *, #35022, .T. ) ; +#70980 = SURFACE_STYLE_USAGE ( .BOTH. , #98022 ) ; +#70981 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#70982 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#70983 = LINE ( 'NONE', #33196, #74991 ) ; +#70984 = AXIS2_PLACEMENT_3D ( 'NONE', #96061, #88433, #51160 ) ; +#70985 = SURFACE_SIDE_STYLE ('',( #94939 ) ) ; +#70986 = ORIENTED_EDGE ( 'NONE', *, *, #41540, .F. ) ; +#70987 = LINE ( 'NONE', #24570, #58300 ) ; +#70988 = STYLED_ITEM ( 'NONE', ( #87093 ), #49431 ) ; +#70989 = ORIENTED_EDGE ( 'NONE', *, *, #16458, .T. ) ; +#70990 = FILL_AREA_STYLE ('',( #54688 ) ) ; +#70991 = AXIS2_PLACEMENT_3D ( 'NONE', #48570, #35273, #80217 ) ; +#70992 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92184 ) ) ; +#70993 = ORIENTED_EDGE ( 'NONE', *, *, #37454, .F. ) ; +#70994 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#70996 = STYLED_ITEM ( 'NONE', ( #57207 ), #25778 ) ; +#70995 = SURFACE_SIDE_STYLE ('',( #48022 ) ) ; +#70997 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#70998 = SURFACE_STYLE_USAGE ( .BOTH. , #15836 ) ; +#70999 = SURFACE_STYLE_FILL_AREA ( #32208 ) ; +#71000 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33569 ), #36756 ) ; +#71001 = FACE_OUTER_BOUND ( 'NONE', #45708, .T. ) ; +#71002 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71004 = ORIENTED_EDGE ( 'NONE', *, *, #21973, .F. ) ; +#71003 = ORIENTED_EDGE ( 'NONE', *, *, #5479, .F. ) ; +#71005 = LINE ( 'NONE', #16848, #6205 ) ; +#71006 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#71007 = SURFACE_STYLE_USAGE ( .BOTH. , #8621 ) ; +#71008 = EDGE_LOOP ( 'NONE', ( #21908, #35066, #83840, #30027 ) ) ; +#71009 = FILL_AREA_STYLE ('',( #70490 ) ) ; +#71010 = VECTOR ( 'NONE', #16944, 1000.000000000000000 ) ; +#71011 = VECTOR ( 'NONE', #17213, 1000.000000000000000 ) ; +#71013 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#71012 = PRESENTATION_STYLE_ASSIGNMENT (( #70493 ) ) ; +#71014 = ORIENTED_EDGE ( 'NONE', *, *, #56436, .T. ) ; +#71015 = ADVANCED_FACE ( 'NONE', ( #95748 ), #2876, .T. ) ; +#71016 = EDGE_LOOP ( 'NONE', ( #35138, #82611, #7411, #59655 ) ) ; +#71019 = AXIS2_PLACEMENT_3D ( 'NONE', #54232, #90129, #77706 ) ; +#71018 = STYLED_ITEM ( 'NONE', ( #26104 ), #39019 ) ; +#71017 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, -3.149999999999979927, 0.000000000000000000 ) ) ; +#71020 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.8999999999999991340, 4.860315062863665657E-79 ) ) ; +#71021 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71022 = FILL_AREA_STYLE_COLOUR ( '', #49617 ) ; +#71023 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, 3.500000000000000444, 0.000000000000000000 ) ) ; +#71024 = FACE_OUTER_BOUND ( 'NONE', #16691, .T. ) ; +#71025 = ORIENTED_EDGE ( 'NONE', *, *, #74028, .T. ) ; +#71026 = EDGE_LOOP ( 'NONE', ( #72157, #8475, #49794, #68496 ) ) ; +#71027 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#71028 = ORIENTED_EDGE ( 'NONE', *, *, #80052, .F. ) ; +#71029 = SURFACE_SIDE_STYLE ('',( #24610 ) ) ; +#71031 = ORIENTED_EDGE ( 'NONE', *, *, #93834, .F. ) ; +#71030 = FILL_AREA_STYLE_COLOUR ( '', #36356 ) ; +#71032 = SURFACE_STYLE_USAGE ( .BOTH. , #39889 ) ; +#71033 = FILL_AREA_STYLE_COLOUR ( '', #3195 ) ; +#71034 = ORIENTED_EDGE ( 'NONE', *, *, #50635, .F. ) ; +#71035 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #28215, #58889, #35887, #66997 ), + ( #20525, #82833, #12807, #2724 ), + ( #33880, #64999, #37877, #37388 ), + ( #44497, #99054, #13818, #60385 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541242845573, 0.8047378541242845573, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606230224, 0.6476030138606230224, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606230224, 0.6476030138606230224, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541242845573, 0.8047378541242845573, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#71036 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71037 = ORIENTED_EDGE ( 'NONE', *, *, #49355, .T. ) ; +#71038 = EDGE_CURVE ( 'NONE', #35363, #2963, #22570, .T. ) ; +#71039 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71040 = PRESENTATION_STYLE_ASSIGNMENT (( #23078 ) ) ; +#71041 = LINE ( 'NONE', #39381, #54670 ) ; +#71042 = AXIS2_PLACEMENT_3D ( 'NONE', #28005, #41804, #49986 ) ; +#71043 = ORIENTED_EDGE ( 'NONE', *, *, #62809, .T. ) ; +#71044 = CARTESIAN_POINT ( 'NONE', ( 0.2314326298701299967, 0.6899999999999999467, -4.065758146820641628E-17 ) ) ; +#71045 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71046 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#71047 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77611 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88270, #87755, #2993 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71048 = CARTESIAN_POINT ( 'NONE', ( 1.818404401970810103, -1.294636995308309890, 0.8099999999999996092 ) ) ; +#71049 = ORIENTED_EDGE ( 'NONE', *, *, #47762, .T. ) ; +#71050 = PRESENTATION_STYLE_ASSIGNMENT (( #55261 ) ) ; +#71051 = FILL_AREA_STYLE ('',( #96018 ) ) ; +#71052 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71053 = VECTOR ( 'NONE', #8293, 1000.000000000000000 ) ; +#71054 = AXIS2_PLACEMENT_3D ( 'NONE', #14284, #67446, #69436 ) ; +#71055 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3953 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40696, #33018, #72835 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71056 = FILL_AREA_STYLE ('',( #49611 ) ) ; +#71058 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71057 = LINE ( 'NONE', #8673, #96775 ) ; +#71059 = SURFACE_SIDE_STYLE ('',( #31748 ) ) ; +#71060 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71061 = EDGE_CURVE ( 'NONE', #37515, #29371, #6967, .T. ) ; +#71063 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12370 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56863, #85951, #15981 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71062 = LINE ( 'NONE', #9198, #45004 ) ; +#71064 = STYLED_ITEM ( 'NONE', ( #42287 ), #82615 ) ; +#71065 = VECTOR ( 'NONE', #63345, 1000.000000000000000 ) ; +#71066 = SURFACE_STYLE_FILL_AREA ( #2143 ) ; +#71067 = AXIS2_PLACEMENT_3D ( 'NONE', #93836, #100896, #38753 ) ; +#71068 = ORIENTED_EDGE ( 'NONE', *, *, #27867, .T. ) ; +#71069 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9029 ), #44932 ) ; +#71070 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#71071 = ORIENTED_EDGE ( 'NONE', *, *, #61418, .T. ) ; +#71072 = PLANE ( 'NONE', #6370 ) ; +#71074 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71073 = LINE ( 'NONE', #57291, #19597 ) ; +#71075 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71076 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78534 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12214, #27648, #76082 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71077 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#71078 = ADVANCED_FACE ( 'NONE', ( #6180 ), #21561, .F. ) ; +#71079 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51588 ), #56479 ) ; +#71080 = LINE ( 'NONE', #1124, #6913 ) ; +#71081 = STYLED_ITEM ( 'NONE', ( #5637 ), #22884 ) ; +#71082 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34191, 'distance_accuracy_value', 'NONE'); +#71083 = EDGE_LOOP ( 'NONE', ( #86162, #58290, #40109, #9140 ) ) ; +#71084 = CARTESIAN_POINT ( 'NONE', ( 1.877768173756620085, -1.057175192472970204, 0.8100000000000008304 ) ) ; +#71085 = FILL_AREA_STYLE ('',( #14892 ) ) ; +#71086 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8299999999999999600 ) ) ; +#71087 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71088 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71089 = CYLINDRICAL_SURFACE ( 'NONE', #37255, 0.05000000000000002359 ) ; +#71090 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71091 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.266666666666659946, 0.000000000000000000 ) ) ; +#71092 = PLANE ( 'NONE', #14802 ) ; +#71093 = PLANE ( 'NONE', #64789 ) ; +#71094 = CARTESIAN_POINT ( 'NONE', ( 0.04001441731020210363, -0.9622763341455700115, 0.8299999999999999600 ) ) ; +#71095 = EDGE_CURVE ( 'NONE', #36673, #64996, #45021, .T. ) ; +#71096 = AXIS2_PLACEMENT_3D ( 'NONE', #78184, #1592, #63398 ) ; +#71097 = LINE ( 'NONE', #95547, #22450 ) ; +#71098 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#71099 = ORIENTED_EDGE ( 'NONE', *, *, #9020, .T. ) ; +#71100 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#71101 = ORIENTED_EDGE ( 'NONE', *, *, #66013, .F. ) ; +#71102 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25398 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59150, #95868, #88251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71103 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#71104 = FILL_AREA_STYLE ('',( #24161 ) ) ; +#71105 = CARTESIAN_POINT ( 'NONE', ( 0.03293650051631569903, -1.463352833475739967, 0.8300000000000004041 ) ) ; +#71106 = LINE ( 'NONE', #54288, #17423 ) ; +#71107 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71108 = FACE_OUTER_BOUND ( 'NONE', #95083, .T. ) ; +#71109 = ORIENTED_EDGE ( 'NONE', *, *, #77596, .F. ) ; +#71110 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71111 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71112 = FACE_OUTER_BOUND ( 'NONE', #71643, .T. ) ; +#71113 = ORIENTED_EDGE ( 'NONE', *, *, #78138, .T. ) ; +#71114 = LINE ( 'NONE', #40496, #93406 ) ; +#71115 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71116 = ADVANCED_FACE ( 'NONE', ( #22061 ), #10938, .T. ) ; +#71117 = EDGE_LOOP ( 'NONE', ( #58380, #47564, #21271, #91971 ) ) ; +#71118 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#71119 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#71120 = EDGE_CURVE ( 'NONE', #62858, #68530, #8168, .T. ) ; +#71121 = VECTOR ( 'NONE', #78458, 1000.000000000000114 ) ; +#71122 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71123 = SURFACE_STYLE_USAGE ( .BOTH. , #93548 ) ; +#71124 = PLANE ( 'NONE', #47929 ) ; +#71125 = ORIENTED_EDGE ( 'NONE', *, *, #95693, .F. ) ; +#71126 = SURFACE_STYLE_FILL_AREA ( #94056 ) ; +#71127 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#71128 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71129 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18933 ) ) ; +#71130 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40168 ), #59809 ) ; +#71131 = CARTESIAN_POINT ( 'NONE', ( 0.4481429611221979803, -1.007711706028959986, 0.8300000000000002931 ) ) ; +#71132 = ADVANCED_FACE ( 'NONE', ( #1100 ), #55258, .T. ) ; +#71133 = VERTEX_POINT ( 'NONE', #48082 ) ; +#71134 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38213 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63644, #25354, #79967 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71135 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71136 = FACE_OUTER_BOUND ( 'NONE', #12144, .T. ) ; +#71137 = STYLED_ITEM ( 'NONE', ( #69757 ), #78668 ) ; +#71138 = PRESENTATION_STYLE_ASSIGNMENT (( #48682 ) ) ; +#71139 = VECTOR ( 'NONE', #75518, 1000.000000000000000 ) ; +#71140 = EDGE_LOOP ( 'NONE', ( #31319, #5937, #55641, #60873 ) ) ; +#71141 = VERTEX_POINT ( 'NONE', #79218 ) ; +#71142 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71143 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100939 ) ; +#71144 = ORIENTED_EDGE ( 'NONE', *, *, #99916, .F. ) ; +#71145 = FILL_AREA_STYLE_COLOUR ( '', #39363 ) ; +#71146 = STYLED_ITEM ( 'NONE', ( #51465 ), #77765 ) ; +#71147 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70362 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59692, #19837, #82147 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71148 = VERTEX_POINT ( 'NONE', #63908 ) ; +#71150 = ORIENTED_EDGE ( 'NONE', *, *, #79749, .F. ) ; +#71149 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8648700000000000276 ) ) ; +#71151 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62720 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29042, #59225, #100735 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71152 = PLANE ( 'NONE', #64408 ) ; +#71153 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#71154 = ORIENTED_EDGE ( 'NONE', *, *, #93708, .F. ) ; +#71155 = CARTESIAN_POINT ( 'NONE', ( 1.775366595766980193, -1.422222704560690332, 0.8099999999999997202 ) ) ; +#71156 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.7000000000000005107, -0.02000000000000000042 ) ) ; +#71157 = ORIENTED_EDGE ( 'NONE', *, *, #80692, .F. ) ; +#71158 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71159 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#71160 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71161 = ORIENTED_EDGE ( 'NONE', *, *, #62462, .F. ) ; +#71163 = SURFACE_SIDE_STYLE ('',( #94100 ) ) ; +#71162 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71164 = VERTEX_POINT ( 'NONE', #7659 ) ; +#71165 = EDGE_CURVE ( 'NONE', #55998, #85062, #31235, .T. ) ; +#71166 = AXIS2_PLACEMENT_3D ( 'NONE', #92308, #32060, #15694 ) ; +#71167 = EDGE_CURVE ( 'NONE', #98298, #19781, #78219, .T. ) ; +#71168 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71169 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58167 ), #4334 ) ; +#71170 = LINE ( 'NONE', #85980, #22944 ) ; +#71171 = VECTOR ( 'NONE', #2866, 1000.000000000000000 ) ; +#71172 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71173 = ORIENTED_EDGE ( 'NONE', *, *, #49408, .F. ) ; +#71174 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71175 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, -3.500000000000000444, 0.000000000000000000 ) ) ; +#71176 = EDGE_CURVE ( 'NONE', #55609, #80595, #85348, .T. ) ; +#71177 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71178 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -1.699999999999999956, 0.000000000000000000 ) ) ; +#71179 = AXIS2_PLACEMENT_3D ( 'NONE', #6183, #69002, #100065 ) ; +#71180 = SURFACE_STYLE_FILL_AREA ( #8805 ) ; +#71181 = SURFACE_STYLE_USAGE ( .BOTH. , #17535 ) ; +#71182 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#71183 = SURFACE_STYLE_USAGE ( .BOTH. , #8808 ) ; +#71184 = ORIENTED_EDGE ( 'NONE', *, *, #27337, .T. ) ; +#71185 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71187 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71186 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#71189 = SURFACE_STYLE_USAGE ( .BOTH. , #40057 ) ; +#71188 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#71190 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37035, 'distance_accuracy_value', 'NONE'); +#71191 = SURFACE_STYLE_FILL_AREA ( #69658 ) ; +#71192 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71193 = EDGE_CURVE ( 'NONE', #13305, #27266, #86372, .T. ) ; +#71194 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67956 ) ) ; +#71195 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71196 = FACE_OUTER_BOUND ( 'NONE', #51152, .T. ) ; +#71197 = EDGE_LOOP ( 'NONE', ( #61855, #45844, #53819, #74045 ) ) ; +#71198 = STYLED_ITEM ( 'NONE', ( #94786 ), #54742 ) ; +#71200 = EDGE_CURVE ( 'NONE', #66499, #15222, #24922, .T. ) ; +#71199 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#71201 = VECTOR ( 'NONE', #968, 1000.000000000000227 ) ; +#71202 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#71203 = FILL_AREA_STYLE_COLOUR ( '', #90901 ) ; +#71204 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#71205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71206 = PRESENTATION_STYLE_ASSIGNMENT (( #48758 ) ) ; +#71207 = FACE_OUTER_BOUND ( 'NONE', #81414, .T. ) ; +#71208 = ADVANCED_FACE ( 'NONE', ( #26623 ), #80243, .T. ) ; +#71209 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71210 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24162 ) ) ; +#71211 = CARTESIAN_POINT ( 'NONE', ( 1.178090748447750080, -1.443574297695930264, 0.8299999999999999600 ) ) ; +#71212 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71213 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, -0.1500000000000000222 ) ) ; +#71214 = EDGE_CURVE ( 'NONE', #57759, #45227, #56568, .T. ) ; +#71215 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #41343, #49499, #95412, #25521 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#71216 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999378, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#71217 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89156 ), #97282 ) ; +#71218 = ORIENTED_EDGE ( 'NONE', *, *, #82717, .F. ) ; +#71219 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71220 = ORIENTED_EDGE ( 'NONE', *, *, #23868, .T. ) ; +#71221 = FACE_OUTER_BOUND ( 'NONE', #25112, .T. ) ; +#71222 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#71223 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#71224 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71225 = LINE ( 'NONE', #22246, #65064 ) ; +#71226 = CARTESIAN_POINT ( 'NONE', ( -1.016236428037849970, -1.189797473215369994, 0.8299999999999999600 ) ) ; +#71227 = ORIENTED_EDGE ( 'NONE', *, *, #27258, .F. ) ; +#71228 = SURFACE_STYLE_FILL_AREA ( #71741 ) ; +#71229 = FILL_AREA_STYLE ('',( #70205 ) ) ; +#71230 = VECTOR ( 'NONE', #21333, 1000.000000000000000 ) ; +#71231 = STYLED_ITEM ( 'NONE', ( #98639 ), #99966 ) ; +#71232 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.09999999999999881206, 0.1829999999999749605 ) ) ; +#71233 = ORIENTED_EDGE ( 'NONE', *, *, #64243, .T. ) ; +#71234 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#71235 = VECTOR ( 'NONE', #51714, 1000.000000000000000 ) ; +#71236 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71237 = EDGE_CURVE ( 'NONE', #99634, #1317, #10129, .T. ) ; +#71238 = LINE ( 'NONE', #72758, #35913 ) ; +#71239 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#71240 = VERTEX_POINT ( 'NONE', #64906 ) ; +#71241 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71242 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#71243 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76065, 'distance_accuracy_value', 'NONE'); +#71244 = SURFACE_SIDE_STYLE ('',( #1304 ) ) ; +#71245 = CARTESIAN_POINT ( 'NONE', ( 1.877682030168899896, -1.070769809704489983, 0.8099999999999998312 ) ) ; +#71246 = EDGE_CURVE ( 'NONE', #45383, #49127, #28498, .T. ) ; +#71247 = ORIENTED_EDGE ( 'NONE', *, *, #100356, .T. ) ; +#71248 = SURFACE_STYLE_USAGE ( .BOTH. , #17115 ) ; +#71249 = ORIENTED_EDGE ( 'NONE', *, *, #82733, .F. ) ; +#71250 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#71251 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71252 = ADVANCED_FACE ( 'NONE', ( #56267 ), #87372, .F. ) ; +#71253 = AXIS2_PLACEMENT_3D ( 'NONE', #64284, #95391, #17298 ) ; +#71254 = FACE_OUTER_BOUND ( 'NONE', #71921, .T. ) ; +#71255 = PLANE ( 'NONE', #61249 ) ; +#71256 = ADVANCED_FACE ( 'NONE', ( #12718 ), #21320, .F. ) ; +#71257 = ORIENTED_EDGE ( 'NONE', *, *, #8677, .T. ) ; +#71259 = VERTEX_POINT ( 'NONE', #69900 ) ; +#71258 = PRESENTATION_STYLE_ASSIGNMENT (( #40139 ) ) ; +#71260 = AXIS2_PLACEMENT_3D ( 'NONE', #49773, #29155, #42094 ) ; +#71261 = STYLED_ITEM ( 'NONE', ( #14137 ), #90825 ) ; +#71262 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55135, 'distance_accuracy_value', 'NONE'); +#71263 = CARTESIAN_POINT ( 'NONE', ( 10.49026475025008764, 7.544011249749912551, 0.8648700000000000276 ) ) ; +#71265 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71264 = FILL_AREA_STYLE_COLOUR ( '', #44339 ) ; +#71266 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71267 = CARTESIAN_POINT ( 'NONE', ( -0.4015774049763590758, -0.9593865114130070149, 0.8299999999999999600 ) ) ; +#71268 = ORIENTED_EDGE ( 'NONE', *, *, #98315, .F. ) ; +#71269 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90818 ) ) ; +#71270 = SURFACE_SIDE_STYLE ('',( #2354 ) ) ; +#71271 = VERTEX_POINT ( 'NONE', #63309 ) ; +#71272 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71274 = SURFACE_SIDE_STYLE ('',( #1337 ) ) ; +#71273 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#71275 = ORIENTED_EDGE ( 'NONE', *, *, #80978, .F. ) ; +#71276 = EDGE_CURVE ( 'NONE', #68559, #9382, #78574, .T. ) ; +#71277 = ORIENTED_EDGE ( 'NONE', *, *, #18225, .T. ) ; +#71278 = EDGE_CURVE ( 'NONE', #62758, #87120, #39268, .T. ) ; +#71279 = SURFACE_SIDE_STYLE ('',( #47803 ) ) ; +#71280 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71281 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#71282 = PLANE ( 'NONE', #22871 ) ; +#71283 = VECTOR ( 'NONE', #26828, 1000.000000000000000 ) ; +#71284 = ORIENTED_EDGE ( 'NONE', *, *, #63272, .T. ) ; +#71285 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#71286 = PRESENTATION_STYLE_ASSIGNMENT (( #3235 ) ) ; +#71287 = AXIS2_PLACEMENT_3D ( 'NONE', #25411, #48882, #34069 ) ; +#71288 = VECTOR ( 'NONE', #6622, 1000.000000000000000 ) ; +#71289 = SURFACE_STYLE_USAGE ( .BOTH. , #54484 ) ; +#71290 = ORIENTED_EDGE ( 'NONE', *, *, #73119, .T. ) ; +#71291 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20709 ) ) ; +#71292 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71293 = VERTEX_POINT ( 'NONE', #38286 ) ; +#71294 = ORIENTED_EDGE ( 'NONE', *, *, #33008, .F. ) ; +#71295 = PRESENTATION_STYLE_ASSIGNMENT (( #76951 ) ) ; +#71296 = CLOSED_SHELL ( 'NONE', ( #25822, #43415, #15200, #38329, #90825, #44993 ) ) ; +#71297 = SURFACE_STYLE_FILL_AREA ( #65149 ) ; +#71298 = PRESENTATION_STYLE_ASSIGNMENT (( #54494 ) ) ; +#71299 = EDGE_CURVE ( 'NONE', #9766, #83048, #16946, .T. ) ; +#71300 = LINE ( 'NONE', #1358, #62985 ) ; +#71301 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38716 ) ) ; +#71302 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 3.614007241618339896E-16 ) ) ; +#71303 = EDGE_CURVE ( 'NONE', #70688, #77117, #78090, .T. ) ; +#71304 = STYLED_ITEM ( 'NONE', ( #44456 ), #100326 ) ; +#71305 = PRESENTATION_STYLE_ASSIGNMENT (( #85609 ) ) ; +#71306 = DIRECTION ( 'NONE', ( -0.3387340427540269649, 0.000000000000000000, -0.9408821649279537347 ) ) ; +#71307 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#71308 = STYLED_ITEM ( 'NONE', ( #26689 ), #5566 ) ; +#71309 = LINE ( 'NONE', #32526, #34491 ) ; +#71310 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#71311 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46799 ) ) ; +#71312 = VERTEX_POINT ( 'NONE', #30094 ) ; +#71313 = CARTESIAN_POINT ( 'NONE', ( 1.220343482084889963, -1.445215125000139933, 0.8299999999999994049 ) ) ; +#71315 = SURFACE_STYLE_USAGE ( .BOTH. , #56538 ) ; +#71314 = SURFACE_STYLE_USAGE ( .BOTH. , #9940 ) ; +#71316 = FILL_AREA_STYLE ('',( #15647 ) ) ; +#71317 = FILL_AREA_STYLE_COLOUR ( '', #2437 ) ; +#71318 = ADVANCED_FACE ( 'NONE', ( #100920 ), #81632, .F. ) ; +#71319 = SURFACE_SIDE_STYLE ('',( #97157 ) ) ; +#71320 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#71321 = LINE ( 'NONE', #347, #43552 ) ; +#71322 = CARTESIAN_POINT ( 'NONE', ( 1.980215352946615104, 1.426814750214819849, -11.41256781350644012 ) ) ; +#71323 = SURFACE_STYLE_FILL_AREA ( #40197 ) ; +#71324 = ORIENTED_EDGE ( 'NONE', *, *, #62668, .T. ) ; +#71325 = LINE ( 'NONE', #25396, #74942 ) ; +#71327 = EDGE_CURVE ( 'NONE', #87112, #9228, #1500, .T. ) ; +#71326 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61394, 'distance_accuracy_value', 'NONE'); +#71328 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146551342, 0.5686465759269651032, 0.8299999999999999600 ) ) ; +#71329 = FILL_AREA_STYLE_COLOUR ( '', #50176 ) ; +#71330 = SURFACE_STYLE_FILL_AREA ( #48875 ) ; +#71331 = VECTOR ( 'NONE', #28864, 1000.000000000000114 ) ; +#71332 = FILL_AREA_STYLE_COLOUR ( '', #72316 ) ; +#71333 = LINE ( 'NONE', #32554, #4071 ) ; +#71334 = SURFACE_STYLE_FILL_AREA ( #31529 ) ; +#71335 = FILL_AREA_STYLE_COLOUR ( '', #16304 ) ; +#71336 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64313 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21334, #99349, #59690 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71337 = FACE_OUTER_BOUND ( 'NONE', #50797, .T. ) ; +#71338 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#71339 = FILL_AREA_STYLE_COLOUR ( '', #47125 ) ; +#71340 = ADVANCED_FACE ( 'NONE', ( #2506 ), #87251, .T. ) ; +#71341 = FILL_AREA_STYLE_COLOUR ( '', #7773 ) ; +#71342 = CARTESIAN_POINT ( 'NONE', ( 1.899701586460730285, -1.304291937284929759, 0.8100000000000004974 ) ) ; +#71343 = LINE ( 'NONE', #46828, #81256 ) ; +#71344 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19211 ), #45280 ) ; +#71345 = VECTOR ( 'NONE', #70182, 1000.000000000000000 ) ; +#71346 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71347 = LINE ( 'NONE', #9490, #32926 ) ; +#71348 = ORIENTED_EDGE ( 'NONE', *, *, #77643, .T. ) ; +#71349 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71350 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#71352 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.4999999999999998890, -0.02000000000000000042 ) ) ; +#71351 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31800 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80753, #81763, #26626 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71353 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8099999999998839240 ) ) ; +#71354 = PLANE ( 'NONE', #48796 ) ; +#71355 = STYLED_ITEM ( 'NONE', ( #4461 ), #17022 ) ; +#71356 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, -0.02000000000000000042 ) ) ; +#71357 = EDGE_CURVE ( 'NONE', #71500, #100280, #2343, .T. ) ; +#71358 = VERTEX_POINT ( 'NONE', #95387 ) ; +#71359 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71360 = CARTESIAN_POINT ( 'NONE', ( 1.823014099396639942, -1.319025261726090026, 0.8299999999999994049 ) ) ; +#71361 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#71362 = VECTOR ( 'NONE', #48547, 1000.000000000000000 ) ; +#71363 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71364 = CLOSED_SHELL ( 'NONE', ( #32023, #56134, #4057, #47175, #40447, #70081 ) ) ; +#71365 = FILL_AREA_STYLE ('',( #54566 ) ) ; +#71366 = ADVANCED_FACE ( 'NONE', ( #34175 ), #34673, .T. ) ; +#71367 = AXIS2_PLACEMENT_3D ( 'NONE', #3025, #18828, #88295 ) ; +#71368 = ORIENTED_EDGE ( 'NONE', *, *, #27867, .F. ) ; +#71369 = ORIENTED_EDGE ( 'NONE', *, *, #78540, .F. ) ; +#71370 = VECTOR ( 'NONE', #72483, 1000.000000000000000 ) ; +#71371 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8648700000000000276 ) ) ; +#71372 = ORIENTED_EDGE ( 'NONE', *, *, #21377, .T. ) ; +#71373 = LINE ( 'NONE', #93798, #46035 ) ; +#71374 = VECTOR ( 'NONE', #89891, 1000.000000000000000 ) ; +#71375 = ADVANCED_FACE ( 'NONE', ( #4977 ), #20313, .T. ) ; +#71376 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71377 = FILL_AREA_STYLE_COLOUR ( '', #84262 ) ; +#71378 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8648700000000000276 ) ) ; +#71379 = CARTESIAN_POINT ( 'NONE', ( -1.332669063737389914, -0.9509517096142480197, 0.8299999999999997380 ) ) ; +#71380 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71381 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #24794 ) ; +#71382 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71383 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71385 = ORIENTED_EDGE ( 'NONE', *, *, #1726, .T. ) ; +#71384 = ORIENTED_EDGE ( 'NONE', *, *, #57761, .T. ) ; +#71386 = EDGE_CURVE ( 'NONE', #45519, #55010, #83123, .T. ) ; +#71387 = VERTEX_POINT ( 'NONE', #67279 ) ; +#71388 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71389 = ORIENTED_EDGE ( 'NONE', *, *, #93785, .T. ) ; +#71390 = LINE ( 'NONE', #1455, #83337 ) ; +#71391 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3442, 'distance_accuracy_value', 'NONE'); +#71392 = CARTESIAN_POINT ( 'NONE', ( 1.755956893679319952, -1.501723168847330259, 0.8299999999999999600 ) ) ; +#71393 = FACE_OUTER_BOUND ( 'NONE', #13681, .T. ) ; +#71394 = ORIENTED_EDGE ( 'NONE', *, *, #8380, .T. ) ; +#71395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71396 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71397 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27037 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44470, #83814, #12271 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71398 = ORIENTED_EDGE ( 'NONE', *, *, #6671, .F. ) ; +#71399 = PRESENTATION_STYLE_ASSIGNMENT (( #81605 ) ) ; +#71401 = ORIENTED_EDGE ( 'NONE', *, *, #18836, .T. ) ; +#71400 = CIRCLE ( 'NONE', #84439, 1.200973049130430015 ) ; +#71402 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71403 = EDGE_LOOP ( 'NONE', ( #85942, #69619, #48815, #53828 ) ) ; +#71404 = EDGE_CURVE ( 'NONE', #15064, #15082, #67770, .T. ) ; +#71405 = ORIENTED_EDGE ( 'NONE', *, *, #68115, .F. ) ; +#71406 = EDGE_CURVE ( 'NONE', #76735, #33842, #40630, .T. ) ; +#71407 = LINE ( 'NONE', #30548, #41217 ) ; +#71408 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95794 ), #43696 ) ; +#71409 = SURFACE_SIDE_STYLE ('',( #100407 ) ) ; +#71410 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71411 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71413 = EDGE_LOOP ( 'NONE', ( #11898, #93740, #62896, #39212 ) ) ; +#71412 = DIRECTION ( 'NONE', ( 0.8942439631056318117, 0.4475798637663823132, 0.000000000000000000 ) ) ; +#71414 = ADVANCED_FACE ( 'NONE', ( #66297 ), #11574, .T. ) ; +#71415 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71416 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71417 = VECTOR ( 'NONE', #43458, 1000.000000000000000 ) ; +#71418 = SURFACE_SIDE_STYLE ('',( #16750 ) ) ; +#71419 = LINE ( 'NONE', #8020, #78266 ) ; +#71420 = ORIENTED_EDGE ( 'NONE', *, *, #3079, .T. ) ; +#71422 = SURFACE_SIDE_STYLE ('',( #70919 ) ) ; +#71421 = FACE_OUTER_BOUND ( 'NONE', #53107, .T. ) ; +#71423 = PLANE ( 'NONE', #23325 ) ; +#71424 = ORIENTED_EDGE ( 'NONE', *, *, #16895, .F. ) ; +#71425 = ORIENTED_EDGE ( 'NONE', *, *, #78901, .T. ) ; +#71426 = SURFACE_SIDE_STYLE ('',( #64271 ) ) ; +#71427 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92588 ) ) ; +#71428 = PRESENTATION_STYLE_ASSIGNMENT (( #55630 ) ) ; +#71429 = ADVANCED_FACE ( 'NONE', ( #90782 ), #27509, .T. ) ; +#71430 = STYLED_ITEM ( 'NONE', ( #26244 ), #79455 ) ; +#71431 = CARTESIAN_POINT ( 'NONE', ( -0.4124892269281669743, -1.212011904613210067, 0.8100000000000000533 ) ) ; +#71432 = EDGE_CURVE ( 'NONE', #36275, #93316, #857, .T. ) ; +#71433 = LINE ( 'NONE', #1495, #4584 ) ; +#71435 = CIRCLE ( 'NONE', #19225, 0.05000000000000002359 ) ; +#71434 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62202, 'distance_accuracy_value', 'NONE'); +#71436 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#71437 = ORIENTED_EDGE ( 'NONE', *, *, #57625, .T. ) ; +#71438 = CARTESIAN_POINT ( 'NONE', ( 0.4190707317248760222, -1.180616848856389955, 0.8299999999999999600 ) ) ; +#71439 = STYLED_ITEM ( 'NONE', ( #100578 ), #24495 ) ; +#71440 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90970 ), #53514 ) ; +#71441 = VERTEX_POINT ( 'NONE', #78467 ) ; +#71442 = VECTOR ( 'NONE', #43797, 1000.000000000000000 ) ; +#71443 = VECTOR ( 'NONE', #20993, 1000.000000000000000 ) ; +#71444 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14316 ), #97505 ) ; +#71446 = FACE_OUTER_BOUND ( 'NONE', #38961, .T. ) ; +#71445 = LINE ( 'NONE', #54110, #10340 ) ; +#71447 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71448 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71449 = CLOSED_SHELL ( 'NONE', ( #60229, #6194, #98850, #62059, #61524, #8728 ) ) ; +#71450 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#71451 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76982 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40871, #2057, #12654 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71452 = LINE ( 'NONE', #87264, #39547 ) ; +#71453 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#71454 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#71455 = FILL_AREA_STYLE ('',( #63326 ) ) ; +#71456 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#71457 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#71458 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2499999999999997780, 0.000000000000000000 ) ) ; +#71459 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3664 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14893, #70053, #62433 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71460 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.9238200612200849760, 0.000000000000000000 ) ) ; +#71461 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#71462 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#71463 = ADVANCED_FACE ( 'NONE', ( #53980 ), #29968, .T. ) ; +#71464 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8199999999999999512 ) ) ; +#71465 = ADVANCED_FACE ( 'NONE', ( #62172 ), #45772, .T. ) ; +#71466 = VERTEX_POINT ( 'NONE', #48858 ) ; +#71467 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#71468 = VECTOR ( 'NONE', #57907, 1000.000000000000000 ) ; +#71469 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88041, 'distance_accuracy_value', 'NONE'); +#71470 = ORIENTED_EDGE ( 'NONE', *, *, #90588, .F. ) ; +#71472 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25028, 'distance_accuracy_value', 'NONE'); +#71471 = CARTESIAN_POINT ( 'NONE', ( -0.1238200612200840572, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#71473 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71474 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71475 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71476 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71477 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9100 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62828, #17320, #50029 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71478 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66697 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90871, #58755, #67855 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71479 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#71480 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 9.700687000000002058, 0.8991599999999999593 ) ) ; +#71481 = VECTOR ( 'NONE', #97164, 1000.000000000000114 ) ; +#71482 = VERTEX_POINT ( 'NONE', #94768 ) ; +#71483 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#71484 = EDGE_CURVE ( 'NONE', #86671, #52301, #55287, .T. ) ; +#71485 = EDGE_LOOP ( 'NONE', ( #93961, #76413, #94942, #82693 ) ) ; +#71486 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71487 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78158, 'distance_accuracy_value', 'NONE'); +#71488 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, 0.000000000000000000 ) ) ; +#71489 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14363 ), #33984 ) ; +#71490 = FILL_AREA_STYLE_COLOUR ( '', #69409 ) ; +#71491 = SURFACE_SIDE_STYLE ('',( #47492 ) ) ; +#71492 = FACE_OUTER_BOUND ( 'NONE', #64761, .T. ) ; +#71493 = FACE_OUTER_BOUND ( 'NONE', #72697, .T. ) ; +#71494 = FILL_AREA_STYLE ('',( #88324 ) ) ; +#71495 = ORIENTED_EDGE ( 'NONE', *, *, #52722, .T. ) ; +#71497 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 4.241823000000000121, 0.8648700000000000276 ) ) ; +#71496 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11023 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56571, #39194, #70847 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71498 = EDGE_CURVE ( 'NONE', #80244, #93449, #65665, .T. ) ; +#71499 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8991599999999999593 ) ) ; +#71500 = VERTEX_POINT ( 'NONE', #9939 ) ; +#71501 = PRESENTATION_STYLE_ASSIGNMENT (( #93921 ) ) ; +#71502 = EDGE_LOOP ( 'NONE', ( #25833, #630, #40448, #83195 ) ) ; +#71503 = FILL_AREA_STYLE ('',( #64345 ) ) ; +#71504 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#71505 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71506 = SURFACE_SIDE_STYLE ('',( #2570 ) ) ; +#71507 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71508 = SURFACE_STYLE_USAGE ( .BOTH. , #62353 ) ; +#71509 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71510 = FILL_AREA_STYLE ('',( #56724 ) ) ; +#71511 = SURFACE_STYLE_USAGE ( .BOTH. , #96969 ) ; +#71512 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71513 = VECTOR ( 'NONE', #44690, 1000.000000000000000 ) ; +#71515 = ORIENTED_EDGE ( 'NONE', *, *, #35712, .T. ) ; +#71514 = ORIENTED_EDGE ( 'NONE', *, *, #80481, .F. ) ; +#71516 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22155 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41691, #3387, #35050 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71517 = EDGE_CURVE ( 'NONE', #89241, #34794, #95767, .T. ) ; +#71518 = PLANE ( 'NONE', #81087 ) ; +#71519 = SURFACE_STYLE_USAGE ( .BOTH. , #63382 ) ; +#71521 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92899 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14039, #30381, #776 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71520 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71522 = ORIENTED_EDGE ( 'NONE', *, *, #7167, .F. ) ; +#71523 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#71525 = FILL_AREA_STYLE_COLOUR ( '', #77482 ) ; +#71524 = CARTESIAN_POINT ( 'NONE', ( -0.7732345779220779480, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#71526 = VECTOR ( 'NONE', #78947, 1000.000000000000000 ) ; +#71527 = EDGE_LOOP ( 'NONE', ( #53095, #65771, #7498 ) ) ; +#71528 = ADVANCED_FACE ( 'NONE', ( #24888 ), #86632, .T. ) ; +#71529 = VERTEX_POINT ( 'NONE', #87144 ) ; +#71530 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71531 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71532 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#71533 = FACE_OUTER_BOUND ( 'NONE', #21033, .T. ) ; +#71534 = FILL_AREA_STYLE ('',( #47531 ) ) ; +#71535 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#71537 = ORIENTED_EDGE ( 'NONE', *, *, #87311, .F. ) ; +#71536 = AXIS2_PLACEMENT_3D ( 'NONE', #29976, #75958, #84124 ) ; +#71538 = ORIENTED_EDGE ( 'NONE', *, *, #46964, .F. ) ; +#71539 = EDGE_LOOP ( 'NONE', ( #41794, #23598, #98999, #91829 ) ) ; +#71540 = EDGE_CURVE ( 'NONE', #14378, #39791, #17165, .T. ) ; +#71541 = EDGE_CURVE ( 'NONE', #36035, #100163, #25382, .T. ) ; +#71542 = SURFACE_STYLE_USAGE ( .BOTH. , #71029 ) ; +#71543 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #98112, #61425, #76203, #13864 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#71544 = VECTOR ( 'NONE', #76303, 1000.000000000000000 ) ; +#71548 = EDGE_CURVE ( 'NONE', #97325, #47067, #49865, .T. ) ; +#71547 = ORIENTED_EDGE ( 'NONE', *, *, #65471, .T. ) ; +#71546 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45395 ), #40579 ) ; +#71545 = PRESENTATION_STYLE_ASSIGNMENT (( #72529 ) ) ; +#71549 = EDGE_CURVE ( 'NONE', #92419, #95882, #3391, .T. ) ; +#71550 = PLANE ( 'NONE', #60523 ) ; +#71551 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999829818 ) ) ; +#71552 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 9.523910000000002540, 0.8648700000000000276 ) ) ; +#71553 = VERTEX_POINT ( 'NONE', #79498 ) ; +#71554 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.90000000000000036, 0.000000000000000000 ) ) ; +#71555 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#71556 = VERTEX_POINT ( 'NONE', #40692 ) ; +#71557 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71558 = PLANE ( 'NONE', #26926 ) ; +#71559 = EDGE_CURVE ( 'NONE', #94145, #9040, #30828, .T. ) ; +#71560 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14425 ) ) ; +#71561 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71562 = FILL_AREA_STYLE_COLOUR ( '', #91705 ) ; +#71563 = EDGE_CURVE ( 'NONE', #93343, #45692, #50865, .T. ) ; +#71564 = SURFACE_STYLE_USAGE ( .BOTH. , #72064 ) ; +#71565 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94317, #69832, #54036 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71566 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71567 = LINE ( 'NONE', #64403, #94699 ) ; +#71568 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#71569 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#71570 = VERTEX_POINT ( 'NONE', #51370 ) ; +#71572 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71571 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56869 ), #1453 ) ; +#71573 = STYLED_ITEM ( 'NONE', ( #12771 ), #84956 ) ; +#71574 = PLANE ( 'NONE', #96854 ) ; +#71575 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2458578643762690530 ) ) ; +#71576 = SURFACE_STYLE_FILL_AREA ( #62923 ) ; +#71577 = PRESENTATION_STYLE_ASSIGNMENT (( #2138 ) ) ; +#71578 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71579 = VECTOR ( 'NONE', #32468, 1000.000000000000000 ) ; +#71580 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#71581 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76437 ) ) ; +#71582 = FILL_AREA_STYLE_COLOUR ( '', #37938 ) ; +#71583 = PLANE ( 'NONE', #33334 ) ; +#71584 = STYLED_ITEM ( 'NONE', ( #19301 ), #17798 ) ; +#71585 = VERTEX_POINT ( 'NONE', #36050 ) ; +#71586 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#71587 = VECTOR ( 'NONE', #84034, 999.9999999999998863 ) ; +#71588 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19390 ), #66612 ) ; +#71590 = SURFACE_STYLE_USAGE ( .BOTH. , #86393 ) ; +#71589 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#71591 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#71592 = SURFACE_SIDE_STYLE ('',( #40452 ) ) ; +#71593 = SURFACE_STYLE_FILL_AREA ( #20340 ) ; +#71594 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73156 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96007, #41932, #39908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71595 = ADVANCED_FACE ( 'NONE', ( #90136 ), #60049, .T. ) ; +#71596 = VERTEX_POINT ( 'NONE', #28371 ) ; +#71597 = LINE ( 'NONE', #23118, #42450 ) ; +#71598 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71599 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71600 = LINE ( 'NONE', #94540, #59184 ) ; +#71601 = FACE_OUTER_BOUND ( 'NONE', #4808, .T. ) ; +#71602 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71603 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#71604 = CARTESIAN_POINT ( 'NONE', ( -0.09294028489466890641, -0.9003478538782040408, 0.8299999999999999600 ) ) ; +#71605 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.000000000000000000 ) ) ; +#71606 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86353, 'distance_accuracy_value', 'NONE'); +#71607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97646 ) ) ; +#71608 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71609 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71610 = ORIENTED_EDGE ( 'NONE', *, *, #29125, .F. ) ; +#71611 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#71612 = VERTEX_POINT ( 'NONE', #75831 ) ; +#71613 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67902, 'distance_accuracy_value', 'NONE'); +#71615 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77054, 'distance_accuracy_value', 'NONE'); +#71616 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71617 = PRESENTATION_STYLE_ASSIGNMENT (( #17454 ) ) ; +#71618 = SURFACE_STYLE_FILL_AREA ( #38955 ) ; +#71619 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71620 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71621 = SURFACE_STYLE_FILL_AREA ( #30769 ) ; +#71622 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -1.012211148232466841E-16, -1.000000000000000000 ) ) ; +#71623 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8648700000000000276 ) ) ; +#71624 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71625 = ORIENTED_EDGE ( 'NONE', *, *, #35924, .T. ) ; +#71626 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.450000000000000178, 0.000000000000000000 ) ) ; +#71627 = SURFACE_SIDE_STYLE ('',( #54813 ) ) ; +#71629 = EDGE_CURVE ( 'NONE', #2949, #30456, #5836, .T. ) ; +#71628 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71630 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27011, 'distance_accuracy_value', 'NONE'); +#71631 = ORIENTED_EDGE ( 'NONE', *, *, #96045, .T. ) ; +#71632 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#71633 = FILL_AREA_STYLE ('',( #649 ) ) ; +#71634 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71635 = ORIENTED_EDGE ( 'NONE', *, *, #16525, .F. ) ; +#71636 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#71637 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.299999999999999822, -0.02000000000000209943 ) ) ; +#71638 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61876 ) ) ; +#71639 = AXIS2_PLACEMENT_3D ( 'NONE', #58578, #89682, #50901 ) ; +#71640 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.100000000000000311, 0.000000000000000000 ) ) ; +#71641 = FILL_AREA_STYLE_COLOUR ( '', #40062 ) ; +#71642 = PRESENTATION_STYLE_ASSIGNMENT (( #23663 ) ) ; +#71643 = EDGE_LOOP ( 'NONE', ( #26821, #25502, #99783, #84328 ) ) ; +#71644 = VECTOR ( 'NONE', #37839, 1000.000000000000000 ) ; +#71645 = VECTOR ( 'NONE', #16954, 1000.000000000000000 ) ; +#71646 = ORIENTED_EDGE ( 'NONE', *, *, #71120, .T. ) ; +#71647 = VECTOR ( 'NONE', #23894, 1000.000000000000000 ) ; +#71648 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71649 = VERTEX_POINT ( 'NONE', #20700 ) ; +#71650 = AXIS2_PLACEMENT_3D ( 'NONE', #31442, #93178, #55465 ) ; +#71651 = CARTESIAN_POINT ( 'NONE', ( 1.795940028366769914, -1.028719707420159946, 0.8300000000000004041 ) ) ; +#71652 = VECTOR ( 'NONE', #30866, 1000.000000000000000 ) ; +#71653 = FACE_OUTER_BOUND ( 'NONE', #64425, .T. ) ; +#71654 = ORIENTED_EDGE ( 'NONE', *, *, #22509, .F. ) ; +#71656 = ORIENTED_EDGE ( 'NONE', *, *, #54297, .F. ) ; +#71655 = ORIENTED_EDGE ( 'NONE', *, *, #44858, .F. ) ; +#71657 = FILL_AREA_STYLE ('',( #55839 ) ) ; +#71658 = EDGE_LOOP ( 'NONE', ( #49880, #86047, #60143, #42634 ) ) ; +#71659 = PRESENTATION_STYLE_ASSIGNMENT (( #78796 ) ) ; +#71660 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71661 = ORIENTED_EDGE ( 'NONE', *, *, #11659, .T. ) ; +#71662 = VERTEX_POINT ( 'NONE', #37048 ) ; +#71663 = EDGE_CURVE ( 'NONE', #29934, #79525, #11951, .T. ) ; +#71664 = PRESENTATION_STYLE_ASSIGNMENT (( #87983 ) ) ; +#71666 = PRESENTATION_STYLE_ASSIGNMENT (( #57371 ) ) ; +#71665 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71667 = SURFACE_STYLE_FILL_AREA ( #688 ) ; +#71668 = VERTEX_POINT ( 'NONE', #44174 ) ; +#71669 = SURFACE_STYLE_USAGE ( .BOTH. , #88492 ) ; +#71670 = EDGE_LOOP ( 'NONE', ( #71917, #13248, #91476, #71398 ) ) ; +#71671 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#71672 = ORIENTED_EDGE ( 'NONE', *, *, #95257, .T. ) ; +#71673 = EDGE_LOOP ( 'NONE', ( #97908, #49034, #74565, #42948, #74679, #81713 ) ) ; +#71674 = CARTESIAN_POINT ( 'NONE', ( 0.05696903375467490122, -1.121240070007210043, 0.8300000000000002931 ) ) ; +#71675 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12653 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60830, #89931, #52165 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71676 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #74405, #12532, #82080, #97342 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#71677 = EDGE_CURVE ( 'NONE', #17890, #64125, #11447, .T. ) ; +#71679 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71678 = SURFACE_STYLE_FILL_AREA ( #17023 ) ; +#71680 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.000000000000000000 ) ) ; +#71681 = FILL_AREA_STYLE ('',( #3241 ) ) ; +#71682 = ORIENTED_EDGE ( 'NONE', *, *, #80182, .F. ) ; +#71683 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71685 = FILL_AREA_STYLE_COLOUR ( '', #10990 ) ; +#71686 = CIRCLE ( 'NONE', #16185, 0.04999999999999991257 ) ; +#71687 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#71688 = LINE ( 'NONE', #24760, #32780 ) ; +#71689 = ORIENTED_EDGE ( 'NONE', *, *, #19746, .F. ) ; +#71690 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71691 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71692 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990585, 0.000000000000000000 ) ) ; +#71693 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71694 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1601 ) ) ; +#71695 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#71696 = ORIENTED_EDGE ( 'NONE', *, *, #93270, .F. ) ; +#71697 = EDGE_CURVE ( 'NONE', #63665, #33002, #27897, .T. ) ; +#71698 = SURFACE_STYLE_FILL_AREA ( #32900 ) ; +#71700 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71699 = LINE ( 'NONE', #16531, #47973 ) ; +#71701 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#71702 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#71703 = CARTESIAN_POINT ( 'NONE', ( 0.2473788005703330406, -1.399092671493430196, 0.8299999999999999600 ) ) ; +#71704 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71705 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71706 = AXIS2_PLACEMENT_3D ( 'NONE', #35424, #52720, #97627 ) ; +#71707 = PLANE ( 'NONE', #2809 ) ; +#71708 = SURFACE_STYLE_FILL_AREA ( #72209 ) ; +#71709 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58696 ) ) ; +#71710 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#71711 = EDGE_LOOP ( 'NONE', ( #86514, #17891, #9050, #12526 ) ) ; +#71712 = SURFACE_SIDE_STYLE ('',( #63062 ) ) ; +#71713 = PRESENTATION_STYLE_ASSIGNMENT (( #64557 ) ) ; +#71714 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71715 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#71716 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71717 = AXIS2_PLACEMENT_3D ( 'NONE', #72573, #26143, #65411 ) ; +#71718 = PLANE ( 'NONE', #8902 ) ; +#71719 = DIRECTION ( 'NONE', ( 0.7071090539100477468, -0.7071045084557425753, 0.000000000000000000 ) ) ; +#71720 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#71721 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71722 = SURFACE_STYLE_USAGE ( .BOTH. , #64071 ) ; +#71723 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71724 = SURFACE_STYLE_FILL_AREA ( #40596 ) ; +#71725 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7993 ) ) ; +#71726 = STYLED_ITEM ( 'NONE', ( #24900 ), #1589 ) ; +#71727 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #75399 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#71728 = VERTEX_POINT ( 'NONE', #3871 ) ; +#71729 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71730 = ORIENTED_EDGE ( 'NONE', *, *, #16487, .F. ) ; +#71732 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79148, 'distance_accuracy_value', 'NONE'); +#71731 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71733 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90828, 'distance_accuracy_value', 'NONE'); +#71734 = AXIS2_PLACEMENT_3D ( 'NONE', #27386, #67173, #66669 ) ; +#71735 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71736 = FACE_OUTER_BOUND ( 'NONE', #96713, .T. ) ; +#71737 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#71738 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71739 = CARTESIAN_POINT ( 'NONE', ( -1.246499984327120059, -1.124851061273939967, 0.8299999999999999600 ) ) ; +#71740 = VERTEX_POINT ( 'NONE', #35055 ) ; +#71741 = FILL_AREA_STYLE ('',( #100729 ) ) ; +#71743 = EDGE_CURVE ( 'NONE', #98006, #81623, #39931, .T. ) ; +#71742 = SURFACE_SIDE_STYLE ('',( #1285 ) ) ; +#71744 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61531, 'distance_accuracy_value', 'NONE'); +#71745 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#71746 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71747 = STYLED_ITEM ( 'NONE', ( #19336 ), #51254 ) ; +#71748 = ORIENTED_EDGE ( 'NONE', *, *, #84434, .F. ) ; +#71749 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71750 = ADVANCED_FACE ( 'NONE', ( #19704 ), #43174, .F. ) ; +#71751 = STYLED_ITEM ( 'NONE', ( #35337 ), #9781 ) ; +#71752 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#71753 = CARTESIAN_POINT ( 'NONE', ( -1.222915055115519900, -1.432449005990839908, 0.8100000000000000533 ) ) ; +#71754 = PLANE ( 'NONE', #90335 ) ; +#71755 = EDGE_LOOP ( 'NONE', ( #97462, #62325, #94359, #15464, #99051, #50715 ) ) ; +#71756 = SURFACE_STYLE_FILL_AREA ( #48802 ) ; +#71757 = CIRCLE ( 'NONE', #79936, 0.02999999999999997113 ) ; +#71758 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#71759 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20307, 'distance_accuracy_value', 'NONE'); +#71760 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71761 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.525171249457494580E-10, 0.000000000000000000 ) ) ; +#71762 = CARTESIAN_POINT ( 'NONE', ( 1.810920360744870061, -1.177156496261070107, 0.8099999999999998312 ) ) ; +#71763 = EDGE_CURVE ( 'NONE', #65265, #69981, #17435, .T. ) ; +#71764 = ORIENTED_EDGE ( 'NONE', *, *, #15585, .F. ) ; +#71765 = ADVANCED_FACE ( 'NONE', ( #60545 ), #38536, .F. ) ; +#71766 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71767 = ORIENTED_EDGE ( 'NONE', *, *, #30395, .F. ) ; +#71768 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71769 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8099999999999776268 ) ) ; +#71770 = CARTESIAN_POINT ( 'NONE', ( 2.449293598294706538E-17, 0.6700000000000000400, -0.2000000000000000111 ) ) ; +#71771 = SURFACE_SIDE_STYLE ('',( #40131 ) ) ; +#71772 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#71773 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79951 ) ) ; +#71774 = VECTOR ( 'NONE', #54479, 1000.000000000000000 ) ; +#71775 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8694 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52630, #29617, #60307 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71776 = STYLED_ITEM ( 'NONE', ( #37279 ), #57526 ) ; +#71777 = VERTEX_POINT ( 'NONE', #39540 ) ; +#71780 = VERTEX_POINT ( 'NONE', #6319 ) ; +#71779 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#71778 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39101 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19638, #28794, #59986 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71781 = EDGE_CURVE ( 'NONE', #30965, #51759, #46676, .T. ) ; +#71782 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1679 ) ) ; +#71783 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#71785 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71786 = SURFACE_SIDE_STYLE ('',( #8896 ) ) ; +#71787 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691640, 0.4808578643762691507, -0.2500000000000000000 ) ) ; +#71788 = ORIENTED_EDGE ( 'NONE', *, *, #76188, .T. ) ; +#71789 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8648700000000000276 ) ) ; +#71790 = PLANE ( 'NONE', #83873 ) ; +#71791 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82188 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15795, #62307, #93386 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71792 = PRESENTATION_STYLE_ASSIGNMENT (( #88124 ) ) ; +#71793 = EDGE_LOOP ( 'NONE', ( #26881, #87211, #6139 ) ) ; +#71794 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86505 ), #94643 ) ; +#71795 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#71796 = ORIENTED_EDGE ( 'NONE', *, *, #56707, .F. ) ; +#71797 = ORIENTED_EDGE ( 'NONE', *, *, #6046, .T. ) ; +#71798 = SURFACE_STYLE_FILL_AREA ( #25360 ) ; +#71799 = EDGE_CURVE ( 'NONE', #32073, #96887, #99224, .T. ) ; +#71801 = SURFACE_STYLE_FILL_AREA ( #1857 ) ; +#71800 = SURFACE_STYLE_USAGE ( .BOTH. , #18649 ) ; +#71802 = VECTOR ( 'NONE', #7816, 1000.000000000000000 ) ; +#71803 = LINE ( 'NONE', #30431, #19577 ) ; +#71804 = ORIENTED_EDGE ( 'NONE', *, *, #5314, .T. ) ; +#71805 = AXIS2_PLACEMENT_3D ( 'NONE', #34137, #40271, #96356 ) ; +#71807 = AXIS2_PLACEMENT_3D ( 'NONE', #99113, #37443, #45046 ) ; +#71806 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#71808 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#71809 = VERTEX_POINT ( 'NONE', #53857 ) ; +#71810 = SURFACE_SIDE_STYLE ('',( #40672 ) ) ; +#71811 = VERTEX_POINT ( 'NONE', #7799 ) ; +#71812 = VERTEX_POINT ( 'NONE', #39045 ) ; +#71813 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71815 = SURFACE_SIDE_STYLE ('',( #10411 ) ) ; +#71814 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71816 = CARTESIAN_POINT ( 'NONE', ( 0.6431619866146595088, 0.5992840759270754436, 0.8100000000000000533 ) ) ; +#71817 = LINE ( 'NONE', #55513, #93870 ) ; +#71818 = FILL_AREA_STYLE ('',( #57525 ) ) ; +#71819 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37566 ), #83193 ) ; +#71820 = SURFACE_SIDE_STYLE ('',( #1875 ) ) ; +#71821 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29389 ), #81606 ) ; +#71822 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71823 = CARTESIAN_POINT ( 'NONE', ( 1.027124486614659160, 0.8310340759269658761, 0.8100000000000000533 ) ) ; +#71825 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71824 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39823 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99727, #53890, #22241 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71826 = FILL_AREA_STYLE_COLOUR ( '', #25832 ) ; +#71827 = ORIENTED_EDGE ( 'NONE', *, *, #68016, .T. ) ; +#71828 = ADVANCED_FACE ( 'NONE', ( #45152 ), #56214, .F. ) ; +#71829 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71830 = AXIS2_PLACEMENT_3D ( 'NONE', #25670, #64968, #11245 ) ; +#71831 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#71832 = FILL_AREA_STYLE ('',( #72837 ) ) ; +#71833 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#71834 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8991599999999999593 ) ) ; +#71835 = PRESENTATION_STYLE_ASSIGNMENT (( #72842 ) ) ; +#71836 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#71837 = EDGE_CURVE ( 'NONE', #39359, #12243, #84487, .T. ) ; +#71838 = ORIENTED_EDGE ( 'NONE', *, *, #90553, .T. ) ; +#71839 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#71840 = PRESENTATION_STYLE_ASSIGNMENT (( #8951 ) ) ; +#71841 = SURFACE_STYLE_FILL_AREA ( #87658 ) ; +#71842 = FILL_AREA_STYLE ('',( #78478 ) ) ; +#71843 = VECTOR ( 'NONE', #8926, 1000.000000000000000 ) ; +#71844 = VECTOR ( 'NONE', #34102, 1000.000000000000000 ) ; +#71845 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34003, 'distance_accuracy_value', 'NONE'); +#71846 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71847 = LINE ( 'NONE', #79515, #25063 ) ; +#71848 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 8.003631000000000384, 0.8991599999999999593 ) ) ; +#71849 = VECTOR ( 'NONE', #72181, 1000.000000000000000 ) ; +#71850 = VECTOR ( 'NONE', #90119, 1000.000000000000000 ) ; +#71851 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58818 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4390, #98253, #84019 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71852 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71853 = FILL_AREA_STYLE ('',( #72858 ) ) ; +#71854 = LINE ( 'NONE', #79520, #73265 ) ; +#71855 = LINE ( 'NONE', #8450, #89494 ) ; +#71856 = FILL_AREA_STYLE ('',( #65187 ) ) ; +#71857 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70145 ), #84862 ) ; +#71858 = VECTOR ( 'NONE', #72635, 1000.000000000000000 ) ; +#71859 = CARTESIAN_POINT ( 'NONE', ( 1.830402071067120051, -1.199770973383029737, 0.8100000000000004974 ) ) ; +#71860 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71861 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71862 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90849, 'distance_accuracy_value', 'NONE'); +#71863 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47356 ), #99746 ) ; +#71864 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.000000000000000000 ) ) ; +#71865 = SURFACE_SIDE_STYLE ('',( #40727 ) ) ; +#71866 = ORIENTED_EDGE ( 'NONE', *, *, #69919, .F. ) ; +#71867 = PRESENTATION_STYLE_ASSIGNMENT (( #63718 ) ) ; +#71868 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71869 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71870 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81124, 'distance_accuracy_value', 'NONE'); +#71872 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.000000000000000000, 1.149999999999999911 ) ) ; +#71871 = CARTESIAN_POINT ( 'NONE', ( -0.04841281441248360129, -1.230342595016630014, 0.8300000000000002931 ) ) ; +#71873 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#71874 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71875 = SURFACE_SIDE_STYLE ('',( #56061 ) ) ; +#71876 = EDGE_CURVE ( 'NONE', #42881, #62672, #6795, .T. ) ; +#71877 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.000000000000000000 ) ) ; +#71878 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.28250199999999914, 0.8648700000000000276 ) ) ; +#71879 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16358 ) ) ; +#71880 = ORIENTED_EDGE ( 'NONE', *, *, #61234, .T. ) ; +#71881 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71882 = VECTOR ( 'NONE', #560, 1000.000000000000000 ) ; +#71883 = PLANE ( 'NONE', #69263 ) ; +#71884 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37358, 'distance_accuracy_value', 'NONE'); +#71885 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36919, 'distance_accuracy_value', 'NONE'); +#71886 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#71887 = EDGE_CURVE ( 'NONE', #28450, #75419, #87514, .T. ) ; +#71888 = ORIENTED_EDGE ( 'NONE', *, *, #25339, .F. ) ; +#71889 = ORIENTED_EDGE ( 'NONE', *, *, #94797, .F. ) ; +#71890 = CARTESIAN_POINT ( 'NONE', ( 0.5238200612200860640, 3.099999999999980105, 0.000000000000000000 ) ) ; +#71891 = ORIENTED_EDGE ( 'NONE', *, *, #93809, .F. ) ; +#71893 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#71892 = VECTOR ( 'NONE', #58954, 1000.000000000000000 ) ; +#71894 = EDGE_CURVE ( 'NONE', #45393, #100619, #9824, .T. ) ; +#71895 = FILL_AREA_STYLE ('',( #24445 ) ) ; +#71896 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71897 = SURFACE_SIDE_STYLE ('',( #1941 ) ) ; +#71898 = LINE ( 'NONE', #88223, #25268 ) ; +#71899 = STYLED_ITEM ( 'NONE', ( #9765 ), #10389 ) ; +#71900 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #16218 ) ; +#71901 = FILL_AREA_STYLE_COLOUR ( '', #88378 ) ; +#71903 = ORIENTED_EDGE ( 'NONE', *, *, #35747, .T. ) ; +#71902 = ORIENTED_EDGE ( 'NONE', *, *, #13922, .T. ) ; +#71904 = EDGE_LOOP ( 'NONE', ( #45364, #61097, #66005, #75381 ) ) ; +#71905 = ORIENTED_EDGE ( 'NONE', *, *, #53438, .F. ) ; +#71906 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#71907 = ADVANCED_FACE ( 'NONE', ( #1770 ), #79877, .T. ) ; +#71908 = CARTESIAN_POINT ( 'NONE', ( 1.885232907775660216, -1.407232784796780045, 0.8100000000000000533 ) ) ; +#71909 = SURFACE_STYLE_FILL_AREA ( #424 ) ; +#71910 = VERTEX_POINT ( 'NONE', #55898 ) ; +#71911 = EDGE_CURVE ( 'NONE', #81120, #43057, #95141, .T. ) ; +#71912 = DIRECTION ( 'NONE', ( -0.7071067811865514585, -0.7071067811865435759, 0.000000000000000000 ) ) ; +#71913 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63830 ), #1804 ) ; +#71914 = VECTOR ( 'NONE', #29304, 1000.000000000000000 ) ; +#71915 = ORIENTED_EDGE ( 'NONE', *, *, #77824, .F. ) ; +#71916 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#71917 = ORIENTED_EDGE ( 'NONE', *, *, #36621, .T. ) ; +#71919 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71918 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#71920 = ORIENTED_EDGE ( 'NONE', *, *, #24266, .F. ) ; +#71921 = EDGE_LOOP ( 'NONE', ( #44145, #47162, #21116, #17752 ) ) ; +#71922 = CARTESIAN_POINT ( 'NONE', ( 5.646583000000000574, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#71923 = AXIS2_PLACEMENT_3D ( 'NONE', #90772, #37166, #12074 ) ; +#71924 = EDGE_CURVE ( 'NONE', #37139, #58941, #48234, .T. ) ; +#71925 = ADVANCED_FACE ( 'NONE', ( #64544 ), #47707, .T. ) ; +#71926 = CYLINDRICAL_SURFACE ( 'NONE', #88023, 0.009999999999999998473 ) ; +#71927 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60496 ) ) ; +#71929 = EDGE_LOOP ( 'NONE', ( #79014, #88851, #80691, #69702 ) ) ; +#71928 = FACE_OUTER_BOUND ( 'NONE', #64730, .T. ) ; +#71930 = LINE ( 'NONE', #80606, #93823 ) ; +#71931 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#71932 = AXIS2_PLACEMENT_3D ( 'NONE', #42567, #65520, #3752 ) ; +#71933 = CARTESIAN_POINT ( 'NONE', ( -0.2950099738946450056, -1.071137013546419992, 0.8100000000000000533 ) ) ; +#71934 = LINE ( 'NONE', #1981, #43997 ) ; +#71935 = ORIENTED_EDGE ( 'NONE', *, *, #36505, .T. ) ; +#71936 = ORIENTED_EDGE ( 'NONE', *, *, #18208, .F. ) ; +#71937 = ORIENTED_EDGE ( 'NONE', *, *, #86260, .F. ) ; +#71938 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -2.258754526011470139E-17 ) ) ; +#71939 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86133 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10906, #42159, #56498 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71940 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#71941 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8199999999999999512 ) ) ; +#71942 = VECTOR ( 'NONE', #34331, 1000.000000000000000 ) ; +#71943 = LINE ( 'NONE', #95381, #23243 ) ; +#71944 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71945 = FILL_AREA_STYLE ('',( #48976 ) ) ; +#71946 = AXIS2_PLACEMENT_3D ( 'NONE', #75229, #26765, #57934 ) ; +#71947 = EDGE_LOOP ( 'NONE', ( #83191, #64132, #88861, #57983 ) ) ; +#71948 = FILL_AREA_STYLE_COLOUR ( '', #17956 ) ; +#71949 = EDGE_CURVE ( 'NONE', #5652, #69765, #67362, .T. ) ; +#71950 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31065 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10716, #11715, #18448 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#71951 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71952 = ORIENTED_EDGE ( 'NONE', *, *, #2558, .T. ) ; +#71953 = AXIS2_PLACEMENT_3D ( 'NONE', #55724, #86851, #16864 ) ; +#71954 = LINE ( 'NONE', #69905, #87195 ) ; +#71955 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#71956 = PLANE ( 'NONE', #74849 ) ; +#71957 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#71958 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#71959 = EDGE_CURVE ( 'NONE', #93886, #54843, #7625, .T. ) ; +#71960 = SURFACE_STYLE_FILL_AREA ( #2517 ) ; +#71961 = PLANE ( 'NONE', #55965 ) ; +#71962 = CYLINDRICAL_SURFACE ( 'NONE', #69108, 0.04999999999999991257 ) ; +#71963 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#71964 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#71965 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#71966 = EDGE_CURVE ( 'NONE', #90656, #62724, #54718, .T. ) ; +#71967 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.000000000000000000, -0.2400000000000000189 ) ) ; +#71968 = VECTOR ( 'NONE', #16221, 1000.000000000000000 ) ; +#71969 = STYLED_ITEM ( 'NONE', ( #50078 ), #10597 ) ; +#71970 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#71971 = SURFACE_SIDE_STYLE ('',( #64802 ) ) ; +#71972 = FACE_OUTER_BOUND ( 'NONE', #57890, .T. ) ; +#71973 = EDGE_CURVE ( 'NONE', #86354, #87221, #69993, .T. ) ; +#71975 = VECTOR ( 'NONE', #21255, 1000.000000000000114 ) ; +#71974 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#71976 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#71977 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30597, 'distance_accuracy_value', 'NONE'); +#71978 = ORIENTED_EDGE ( 'NONE', *, *, #49858, .F. ) ; +#71979 = FILL_AREA_STYLE_COLOUR ( '', #19276 ) ; +#71980 = ORIENTED_EDGE ( 'NONE', *, *, #39178, .T. ) ; +#71981 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#71982 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, 1.048695503451053346E-76 ) ) ; +#71983 = CARTESIAN_POINT ( 'NONE', ( 1.812952947087890232, -0.9302426320460149833, 0.8299999999999999600 ) ) ; +#71984 = STYLED_ITEM ( 'NONE', ( #55758 ), #18359 ) ; +#71985 = VECTOR ( 'NONE', #76638, 1000.000000000000000 ) ; +#71986 = SURFACE_STYLE_USAGE ( .BOTH. , #9603 ) ; +#71987 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #40706 ) ; +#71988 = EDGE_CURVE ( 'NONE', #23571, #40957, #6642, .T. ) ; +#71989 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #249 ) ) ; +#71990 = PRESENTATION_STYLE_ASSIGNMENT (( #11612 ) ) ; +#71991 = ORIENTED_EDGE ( 'NONE', *, *, #92153, .F. ) ; +#71992 = FILL_AREA_STYLE ('',( #50920 ) ) ; +#71993 = ORIENTED_EDGE ( 'NONE', *, *, #34504, .T. ) ; +#71994 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#71995 = STYLED_ITEM ( 'NONE', ( #37296 ), #58497 ) ; +#71996 = FACE_OUTER_BOUND ( 'NONE', #28110, .T. ) ; +#71997 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#71998 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.650000000000000355, 0.000000000000000000 ) ) ; +#71999 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 2.061746575926969971, 0.8299999999999999600 ) ) ; +#72000 = STYLED_ITEM ( 'NONE', ( #8681 ), #94777 ) ; +#72001 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#72002 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72003 = SURFACE_STYLE_USAGE ( .BOTH. , #9618 ) ; +#72004 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72005 = PLANE ( 'NONE', #46132 ) ; +#72006 = ORIENTED_EDGE ( 'NONE', *, *, #17844, .F. ) ; +#72007 = FACE_OUTER_BOUND ( 'NONE', #86615, .T. ) ; +#72008 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50817 ), #78539 ) ; +#72009 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, 0.000000000000000000 ) ) ; +#72010 = VERTEX_POINT ( 'NONE', #45979 ) ; +#72011 = FILL_AREA_STYLE ('',( #43238 ) ) ; +#72012 = EDGE_CURVE ( 'NONE', #37735, #41904, #24078, .T. ) ; +#72013 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72014 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72015 = VECTOR ( 'NONE', #44821, 1000.000000000000000 ) ; +#72016 = ORIENTED_EDGE ( 'NONE', *, *, #22661, .T. ) ; +#72017 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72018 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72019 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72020 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72022 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#72023 = VECTOR ( 'NONE', #82076, 1000.000000000000000 ) ; +#72025 = ORIENTED_EDGE ( 'NONE', *, *, #12573, .F. ) ; +#72024 = ORIENTED_EDGE ( 'NONE', *, *, #26082, .T. ) ; +#72026 = STYLED_ITEM ( 'NONE', ( #49308 ), #69922 ) ; +#72027 = LINE ( 'NONE', #33221, #32382 ) ; +#72028 = CARTESIAN_POINT ( 'NONE', ( 8.800278999999999741, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#72029 = SURFACE_STYLE_USAGE ( .BOTH. , #10635 ) ; +#72030 = ORIENTED_EDGE ( 'NONE', *, *, #59604, .F. ) ; +#72031 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, 3.099999999999992539, -0.02000000000000000042 ) ) ; +#72032 = VERTEX_POINT ( 'NONE', #47025 ) ; +#72033 = ORIENTED_EDGE ( 'NONE', *, *, #41856, .T. ) ; +#72034 = CARTESIAN_POINT ( 'NONE', ( -0.03214163119229276888, 0.5753100270687899753, 0.8100000000000001643 ) ) ; +#72035 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#72037 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68192, #99277, #14040, #84530 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#72036 = PRESENTATION_STYLE_ASSIGNMENT (( #42405 ) ) ; +#72038 = CARTESIAN_POINT ( 'NONE', ( -0.1522818774044870371, -0.9679977428869791511, 0.8300000000000000711 ) ) ; +#72040 = FILL_AREA_STYLE ('',( #63880 ) ) ; +#72039 = CYLINDRICAL_SURFACE ( 'NONE', #28570, 0.04341445994558928989 ) ; +#72041 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72042 = ORIENTED_EDGE ( 'NONE', *, *, #76, .T. ) ; +#72043 = VERTEX_POINT ( 'NONE', #77668 ) ; +#72044 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#72045 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81360, #57364, #66009 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72046 = EDGE_LOOP ( 'NONE', ( #91524, #86478, #29969, #57017 ) ) ; +#72047 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999833, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#72048 = EDGE_CURVE ( 'NONE', #39926, #52513, #53690, .T. ) ; +#72049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79915 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30798, #14938, #46088 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72050 = ORIENTED_EDGE ( 'NONE', *, *, #59647, .T. ) ; +#72051 = LINE ( 'NONE', #57770, #47448 ) ; +#72052 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72053 = ORIENTED_EDGE ( 'NONE', *, *, #27520, .T. ) ; +#72054 = FILL_AREA_STYLE_COLOUR ( '', #79419 ) ; +#72055 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8099999999998962474 ) ) ; +#72056 = EDGE_LOOP ( 'NONE', ( #80838, #58862, #15720, #90709 ) ) ; +#72057 = CARTESIAN_POINT ( 'NONE', ( -1.450000000000000400, 0.6892893218813452849, -0.8000000000000001554 ) ) ; +#72058 = SURFACE_STYLE_USAGE ( .BOTH. , #15878 ) ; +#72059 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65544 ) ) ; +#72060 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3555 ), #60623 ) ; +#72061 = SURFACE_STYLE_FILL_AREA ( #39380 ) ; +#72062 = FILL_AREA_STYLE ('',( #62906 ) ) ; +#72063 = VECTOR ( 'NONE', #86789, 1000.000000000000000 ) ; +#72064 = SURFACE_SIDE_STYLE ('',( #24629 ) ) ; +#72065 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22998 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44701, #21739, #61078 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72067 = SURFACE_STYLE_FILL_AREA ( #40936 ) ; +#72066 = FILL_AREA_STYLE_COLOUR ( '', #56274 ) ; +#72068 = CARTESIAN_POINT ( 'NONE', ( 1.602494679827060287, -1.010243534007990052, 0.8299999999999990719 ) ) ; +#72069 = EDGE_LOOP ( 'NONE', ( #98424, #74885, #60176, #4333 ) ) ; +#72070 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72071 = ORIENTED_EDGE ( 'NONE', *, *, #86929, .F. ) ; +#72072 = AXIS2_PLACEMENT_3D ( 'NONE', #77913, #92694, #15076 ) ; +#72073 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#72074 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#72075 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.000000000000000000 ) ) ; +#72076 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -2.299999999999999822, -0.02000000000005030046 ) ) ; +#72077 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8199999999999999512, 0.04999999999999997502 ) ) ; +#72079 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#72078 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#72080 = PRESENTATION_STYLE_ASSIGNMENT (( #47576 ) ) ; +#72082 = ADVANCED_FACE ( 'NONE', ( #85317 ), #85830, .F. ) ; +#72081 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72083 = VECTOR ( 'NONE', #45886, 1000.000000000000000 ) ; +#72084 = FILL_AREA_STYLE ('',( #95019 ) ) ; +#72085 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72086 = VERTEX_POINT ( 'NONE', #93946 ) ; +#72087 = PRESENTATION_STYLE_ASSIGNMENT (( #94528 ) ) ; +#72089 = FACE_OUTER_BOUND ( 'NONE', #13556, .T. ) ; +#72088 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.009999999999999998473, -1.129999999999999893 ) ) ; +#72090 = SURFACE_STYLE_FILL_AREA ( #3144 ) ; +#72091 = EDGE_CURVE ( 'NONE', #49407, #1880, #47532, .T. ) ; +#72092 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39954 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39008, #86989, #70644 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72093 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72094 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72095 = AXIS2_PLACEMENT_3D ( 'NONE', #86950, #15445, #53779 ) ; +#72097 = ADVANCED_FACE ( 'NONE', ( #71024 ), #26094, .F. ) ; +#72096 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76220, 'distance_accuracy_value', 'NONE'); +#72098 = VERTEX_POINT ( 'NONE', #28101 ) ; +#72099 = SURFACE_STYLE_USAGE ( .BOTH. , #10714 ) ; +#72100 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#72101 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333323090, 0.09999999999999939493, 1.747825839084783216E-76 ) ) ; +#72102 = SURFACE_STYLE_USAGE ( .BOTH. , #70566 ) ; +#72103 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72104 = LINE ( 'NONE', #10724, #93777 ) ; +#72105 = FACE_OUTER_BOUND ( 'NONE', #24708, .T. ) ; +#72106 = CARTESIAN_POINT ( 'NONE', ( -1.027917449215540069, -1.416724300735810127, 0.8300000000000001821 ) ) ; +#72107 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72108 = EDGE_CURVE ( 'NONE', #51932, #406, #18898, .T. ) ; +#72109 = DIRECTION ( 'NONE', ( -0.7071060119555159229, -0.7071075504167422254, 0.000000000000000000 ) ) ; +#72110 = EDGE_CURVE ( 'NONE', #43172, #21034, #47842, .T. ) ; +#72111 = CYLINDRICAL_SURFACE ( 'NONE', #81238, 0.2000000000000000944 ) ; +#72112 = ORIENTED_EDGE ( 'NONE', *, *, #31271, .F. ) ; +#72113 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#72114 = ORIENTED_EDGE ( 'NONE', *, *, #14417, .F. ) ; +#72115 = AXIS2_PLACEMENT_3D ( 'NONE', #94472, #79180, #47520 ) ; +#72116 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#72117 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31484, 'distance_accuracy_value', 'NONE'); +#72118 = ADVANCED_FACE ( 'NONE', ( #88867 ), #89859, .T. ) ; +#72119 = ADVANCED_FACE ( 'NONE', ( #35281 ), #51603, .T. ) ; +#72120 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72121 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#72122 = LINE ( 'NONE', #65967, #70532 ) ; +#72123 = SURFACE_STYLE_USAGE ( .BOTH. , #40998 ) ; +#72124 = ORIENTED_EDGE ( 'NONE', *, *, #96826, .T. ) ; +#72125 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999833, 0.000000000000000000, -0.1499999999999999667 ) ) ; +#72126 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000089, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#72127 = CARTESIAN_POINT ( 'NONE', ( -0.7486878350751702271, 1.376286804147143439, 0.8299999999999999600 ) ) ; +#72128 = ORIENTED_EDGE ( 'NONE', *, *, #1230, .F. ) ; +#72129 = SURFACE_SIDE_STYLE ('',( #49666 ) ) ; +#72130 = AXIS2_PLACEMENT_3D ( 'NONE', #33421, #96158, #24769 ) ; +#72131 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72132 = ORIENTED_EDGE ( 'NONE', *, *, #52405, .F. ) ; +#72133 = VECTOR ( 'NONE', #90241, 1000.000000000000000 ) ; +#72134 = SURFACE_SIDE_STYLE ('',( #50189 ) ) ; +#72135 = AXIS2_PLACEMENT_3D ( 'NONE', #37428, #22079, #68524 ) ; +#72136 = ADVANCED_FACE ( 'NONE', ( #90873 ), #43055, .T. ) ; +#72137 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72138 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37941 ) ) ; +#72139 = LINE ( 'NONE', #79803, #25044 ) ; +#72140 = SURFACE_SIDE_STYLE ('',( #88454 ) ) ; +#72141 = CARTESIAN_POINT ( 'NONE', ( 5.363740750249974099, 9.545123249750025352, 0.8991599999999999593 ) ) ; +#72142 = ORIENTED_EDGE ( 'NONE', *, *, #99916, .T. ) ; +#72143 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72144 = ORIENTED_EDGE ( 'NONE', *, *, #90777, .T. ) ; +#72145 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.300000000000000044, 0.000000000000000000 ) ) ; +#72146 = VERTEX_POINT ( 'NONE', #83219 ) ; +#72147 = CARTESIAN_POINT ( 'NONE', ( 1.655237363055763966, -1.164073081312990476, 0.8100000000000000533 ) ) ; +#72148 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72149 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72150 = STYLED_ITEM ( 'NONE', ( #62977 ), #66791 ) ; +#72151 = FILL_AREA_STYLE ('',( #64991 ) ) ; +#72152 = LINE ( 'NONE', #87971, #23898 ) ; +#72153 = ORIENTED_EDGE ( 'NONE', *, *, #45766, .T. ) ; +#72155 = EDGE_LOOP ( 'NONE', ( #36060, #9239, #64091, #34296 ) ) ; +#72154 = ORIENTED_EDGE ( 'NONE', *, *, #21421, .T. ) ; +#72156 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72157 = ORIENTED_EDGE ( 'NONE', *, *, #75234, .T. ) ; +#72158 = ADVANCED_FACE ( 'NONE', ( #77414 ), #93197, .T. ) ; +#72159 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10463 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29590, #59791, #60763 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72160 = ORIENTED_EDGE ( 'NONE', *, *, #14452, .F. ) ; +#72162 = EDGE_LOOP ( 'NONE', ( #30426, #13263, #76898, #46438 ) ) ; +#72161 = SURFACE_SIDE_STYLE ('',( #10264 ) ) ; +#72163 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72164 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4299999999943793227, -0.6500000000642102149 ) ) ; +#72165 = VECTOR ( 'NONE', #80810, 1000.000000000000000 ) ; +#72166 = ORIENTED_EDGE ( 'NONE', *, *, #81936, .F. ) ; +#72168 = ADVANCED_FACE ( 'NONE', ( #63138 ), #85072, .T. ) ; +#72167 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.500000000000000000, -0.02000000000002094894 ) ) ; +#72169 = CARTESIAN_POINT ( 'NONE', ( 1.800644492816920295, -1.399205570841099977, 0.8099999999999997202 ) ) ; +#72170 = VERTEX_POINT ( 'NONE', #1331 ) ; +#72171 = FILL_AREA_STYLE_COLOUR ( '', #12171 ) ; +#72172 = FACE_OUTER_BOUND ( 'NONE', #60472, .T. ) ; +#72173 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72174 = VECTOR ( 'NONE', #58184, 1000.000000000000000 ) ; +#72175 = AXIS2_PLACEMENT_3D ( 'NONE', #70331, #78013, #17210 ) ; +#72176 = ORIENTED_EDGE ( 'NONE', *, *, #47928, .F. ) ; +#72177 = EDGE_LOOP ( 'NONE', ( #47015, #43402, #8809, #59165, #323, #86598 ) ) ; +#72178 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17576 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55615, #46891, #16236 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72179 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#72180 = PLANE ( 'NONE', #906 ) ; +#72181 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72182 = CARTESIAN_POINT ( 'NONE', ( 3.949527124875011896, 8.130909875124988417, 0.8991599999999999593 ) ) ; +#72183 = AXIS2_PLACEMENT_3D ( 'NONE', #95244, #71814, #8925 ) ; +#72184 = FILL_AREA_STYLE_COLOUR ( '', #12389 ) ; +#72185 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#72186 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72187 = PRESENTATION_STYLE_ASSIGNMENT (( #9810 ) ) ; +#72189 = PRESENTATION_STYLE_ASSIGNMENT (( #70153 ) ) ; +#72188 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#72191 = EDGE_CURVE ( 'NONE', #69070, #55093, #51236, .T. ) ; +#72190 = FILL_AREA_STYLE_COLOUR ( '', #70797 ) ; +#72192 = VECTOR ( 'NONE', #64229, 1000.000000000000000 ) ; +#72193 = AXIS2_PLACEMENT_3D ( 'NONE', #72703, #83760, #68413 ) ; +#72194 = CARTESIAN_POINT ( 'NONE', ( -1.032372237264020054, -0.9101533448649530289, 0.8299999999999999600 ) ) ; +#72195 = VERTEX_POINT ( 'NONE', #87106 ) ; +#72196 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6864 ) ) ; +#72197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37939 ) ) ; +#72198 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#72199 = SURFACE_SIDE_STYLE ('',( #56414 ) ) ; +#72200 = EDGE_LOOP ( 'NONE', ( #51615, #33219, #75415, #36661 ) ) ; +#72201 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#72202 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72203 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#72204 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24497, 'distance_accuracy_value', 'NONE'); +#72205 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86792 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83641, #85123, #44792 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72206 = CARTESIAN_POINT ( 'NONE', ( 0.3916958651482640441, -1.284685391536070087, 0.8100000000000000533 ) ) ; +#72207 = SURFACE_STYLE_FILL_AREA ( #56423 ) ; +#72208 = PRESENTATION_STYLE_ASSIGNMENT (( #64552 ) ) ; +#72209 = FILL_AREA_STYLE ('',( #8820 ) ) ; +#72210 = EDGE_CURVE ( 'NONE', #81114, #96832, #88122, .T. ) ; +#72211 = ORIENTED_EDGE ( 'NONE', *, *, #61159, .F. ) ; +#72212 = LINE ( 'NONE', #73720, #20076 ) ; +#72213 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72214 = SURFACE_STYLE_FILL_AREA ( #87533 ) ; +#72215 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#72216 = CARTESIAN_POINT ( 'NONE', ( -2.300000000000000266, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#72217 = SURFACE_STYLE_FILL_AREA ( #26278 ) ; +#72218 = AXIS2_PLACEMENT_3D ( 'NONE', #85667, #54029, #47369 ) ; +#72219 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72220 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72221 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#72222 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72223 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72224 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999990319, -0.02000000000000000042 ) ) ; +#72225 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72226 = LINE ( 'NONE', #79395, #14454 ) ; +#72227 = ORIENTED_EDGE ( 'NONE', *, *, #73160, .T. ) ; +#72228 = AXIS2_PLACEMENT_3D ( 'NONE', #32125, #53094, #63291 ) ; +#72229 = ORIENTED_EDGE ( 'NONE', *, *, #5549, .F. ) ; +#72230 = EDGE_CURVE ( 'NONE', #31723, #62983, #32487, .T. ) ; +#72231 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2808578643762690841, 0.1400000000000000133 ) ) ; +#72232 = CARTESIAN_POINT ( 'NONE', ( 0.2157961956640810364, -1.329502282602879948, 0.8299999999999999600 ) ) ; +#72233 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72234 = LINE ( 'NONE', #62590, #80263 ) ; +#72235 = STYLED_ITEM ( 'NONE', ( #51572 ), #53042 ) ; +#72236 = SHAPE_REPRESENTATION ( 'R0201_20210301.xtd', ( #82894 ), #14322 ) ; +#72237 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#72238 = ORIENTED_EDGE ( 'NONE', *, *, #78556, .T. ) ; +#72239 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#72240 = SURFACE_SIDE_STYLE ('',( #57454 ) ) ; +#72241 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72242 = VECTOR ( 'NONE', #13006, 1000.000000000000000 ) ; +#72243 = FILL_AREA_STYLE ('',( #2811 ) ) ; +#72244 = ORIENTED_EDGE ( 'NONE', *, *, #12216, .F. ) ; +#72245 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28376 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10609, #58224, #18852 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72246 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#72247 = ADVANCED_FACE ( 'NONE', ( #65624 ), #71790, .T. ) ; +#72248 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#72249 = FILL_AREA_STYLE ('',( #95698 ) ) ; +#72250 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72251 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999958471, -0.1458578643762690752 ) ) ; +#72252 = VERTEX_POINT ( 'NONE', #3354 ) ; +#72253 = PRESENTATION_STYLE_ASSIGNMENT (( #32957 ) ) ; +#72254 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72255 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38612, 'distance_accuracy_value', 'NONE'); +#72256 = LINE ( 'NONE', #95201, #91491 ) ; +#72257 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77124 ), #44525 ) ; +#72258 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72259 = ORIENTED_EDGE ( 'NONE', *, *, #13738, .F. ) ; +#72260 = LINE ( 'NONE', #74278, #3996 ) ; +#72261 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72262 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72263 = LINE ( 'NONE', #46740, #60909 ) ; +#72264 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72265 = LINE ( 'NONE', #25334, #32159 ) ; +#72266 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62521 ) ) ; +#72267 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72268 = VECTOR ( 'NONE', #63849, 1000.000000000000000 ) ; +#72269 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #100676, #82894 ) ; +#72270 = ADVANCED_FACE ( 'NONE', ( #1847 ), #56999, .T. ) ; +#72271 = VECTOR ( 'NONE', #7815, 1000.000000000000000 ) ; +#72272 = ORIENTED_EDGE ( 'NONE', *, *, #100645, .F. ) ; +#72274 = EDGE_LOOP ( 'NONE', ( #59373, #75782, #21573, #49168 ) ) ; +#72273 = SURFACE_STYLE_USAGE ( .BOTH. , #35011 ) ; +#72275 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55242, 'distance_accuracy_value', 'NONE'); +#72276 = AXIS2_PLACEMENT_3D ( 'NONE', #97846, #43273, #91727 ) ; +#72277 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#72278 = FILL_AREA_STYLE_COLOUR ( '', #46345 ) ; +#72279 = ADVANCED_FACE ( 'NONE', ( #98692 ), #5812, .T. ) ; +#72280 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72281 = ORIENTED_EDGE ( 'NONE', *, *, #31546, .F. ) ; +#72282 = VERTEX_POINT ( 'NONE', #90105 ) ; +#72283 = SURFACE_STYLE_USAGE ( .BOTH. , #25850 ) ; +#72284 = ORIENTED_EDGE ( 'NONE', *, *, #24964, .T. ) ; +#72285 = ORIENTED_EDGE ( 'NONE', *, *, #4795, .T. ) ; +#72287 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72286 = FILL_AREA_STYLE_COLOUR ( '', #2249 ) ; +#72288 = ORIENTED_EDGE ( 'NONE', *, *, #29553, .F. ) ; +#72289 = LINE ( 'NONE', #11932, #29496 ) ; +#72290 = ORIENTED_EDGE ( 'NONE', *, *, #38769, .F. ) ; +#72291 = CARTESIAN_POINT ( 'NONE', ( 1.363488817166419897, -1.341449062141889970, 0.8299999999999999600 ) ) ; +#72293 = ORIENTED_EDGE ( 'NONE', *, *, #64965, .T. ) ; +#72292 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5422 ), #31557 ) ; +#72294 = EDGE_LOOP ( 'NONE', ( #40260, #523, #23047, #98172 ) ) ; +#72296 = SURFACE_STYLE_USAGE ( .BOTH. , #16136 ) ; +#72295 = SURFACE_SIDE_STYLE ('',( #71297 ) ) ; +#72297 = CARTESIAN_POINT ( 'NONE', ( -0.9982971928311329401, -1.296162859166370307, 0.8100000000000000533 ) ) ; +#72298 = DIRECTION ( 'NONE', ( -0.5479224129540778421, -0.8365291563254571017, 0.000000000000000000 ) ) ; +#72299 = EDGE_CURVE ( 'NONE', #51969, #37756, #90626, .T. ) ; +#72300 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72301 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#72303 = EDGE_CURVE ( 'NONE', #77117, #8845, #43633, .T. ) ; +#72302 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72304 = CARTESIAN_POINT ( 'NONE', ( 3.560618500500175809, 6.822762500500174632, 0.8991599999999999593 ) ) ; +#72305 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72306 = ORIENTED_EDGE ( 'NONE', *, *, #46234, .T. ) ; +#72307 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#72308 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72309 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8648700000000000276 ) ) ; +#72310 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72311 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#72312 = STYLED_ITEM ( 'NONE', ( #66807 ), #19881 ) ; +#72313 = AXIS2_PLACEMENT_3D ( 'NONE', #12997, #36586, #98763 ) ; +#72314 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72315 = SURFACE_SIDE_STYLE ('',( #10960 ) ) ; +#72316 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72317 = CARTESIAN_POINT ( 'NONE', ( 1.980596491615695065, 1.431171544775461824, -11.40909392275420053 ) ) ; +#72318 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72319 = EDGE_CURVE ( 'NONE', #27116, #33248, #3842, .T. ) ; +#72320 = VERTEX_POINT ( 'NONE', #35023 ) ; +#72321 = PRESENTATION_STYLE_ASSIGNMENT (( #31513 ) ) ; +#72322 = EDGE_CURVE ( 'NONE', #42023, #61258, #36020, .T. ) ; +#72323 = PRESENTATION_STYLE_ASSIGNMENT (( #41208 ) ) ; +#72326 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72325 = AXIS2_PLACEMENT_3D ( 'NONE', #93558, #9270, #94069 ) ; +#72324 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72328 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72327 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#72329 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#72330 = CARTESIAN_POINT ( 'NONE', ( 0.4381267573579120111, -1.159910275666830026, 0.8300000000000015143 ) ) ; +#72331 = LINE ( 'NONE', #27393, #5602 ) ; +#72332 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72333 = DIRECTION ( 'NONE', ( 0.000000000000000000, -3.794707603699256053E-15, -1.000000000000000000 ) ) ; +#72334 = SURFACE_STYLE_USAGE ( .BOTH. , #63699 ) ; +#72335 = AXIS2_PLACEMENT_3D ( 'NONE', #60236, #6978, #45339 ) ; +#72336 = STYLED_ITEM ( 'NONE', ( #51303 ), #97105 ) ; +#72337 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72338 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.850000000000000089, 0.000000000000000000 ) ) ; +#72339 = SURFACE_STYLE_USAGE ( .BOTH. , #88671 ) ; +#72340 = PRESENTATION_STYLE_ASSIGNMENT (( #57564 ) ) ; +#72341 = SURFACE_SIDE_STYLE ('',( #18704 ) ) ; +#72342 = EDGE_CURVE ( 'NONE', #56508, #59301, #13430, .T. ) ; +#72343 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72344 = SURFACE_STYLE_USAGE ( .BOTH. , #61819 ) ; +#72345 = ORIENTED_EDGE ( 'NONE', *, *, #47708, .F. ) ; +#72346 = FILL_AREA_STYLE ('',( #26919 ) ) ; +#72347 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8991599999999999593 ) ) ; +#72348 = AXIS2_PLACEMENT_3D ( 'NONE', #40500, #48665, #17974 ) ; +#72350 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72349 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#72351 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#72352 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.000000000000000000 ) ) ; +#72353 = EDGE_CURVE ( 'NONE', #47557, #39315, #20155, .T. ) ; +#72354 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72355 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#72356 = ORIENTED_EDGE ( 'NONE', *, *, #26892, .T. ) ; +#72357 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72358 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#72359 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72360 = FACE_OUTER_BOUND ( 'NONE', #72274, .T. ) ; +#72361 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72362 = SURFACE_SIDE_STYLE ('',( #49403 ) ) ; +#72363 = VECTOR ( 'NONE', #64978, 1000.000000000000000 ) ; +#72364 = PLANE ( 'NONE', #12548 ) ; +#72365 = ORIENTED_EDGE ( 'NONE', *, *, #5697, .T. ) ; +#72366 = EDGE_LOOP ( 'NONE', ( #8271, #2774, #70727, #98736 ) ) ; +#72367 = PRESENTATION_STYLE_ASSIGNMENT (( #17730 ) ) ; +#72368 = FILL_AREA_STYLE ('',( #80565 ) ) ; +#72369 = ORIENTED_EDGE ( 'NONE', *, *, #58428, .F. ) ; +#72370 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72371 = ADVANCED_FACE ( 'NONE', ( #81493 ), #68111, .F. ) ; +#72372 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98394 ) ) ; +#72373 = STYLED_ITEM ( 'NONE', ( #69456 ), #26430 ) ; +#72374 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72375 = PRODUCT_CONTEXT ( 'NONE', #5775, 'mechanical' ) ; +#72377 = ORIENTED_EDGE ( 'NONE', *, *, #47996, .F. ) ; +#72376 = ORIENTED_EDGE ( 'NONE', *, *, #63790, .T. ) ; +#72378 = VECTOR ( 'NONE', #58552, 1000.000000000000000 ) ; +#72379 = ORIENTED_EDGE ( 'NONE', *, *, #50325, .F. ) ; +#72380 = ORIENTED_EDGE ( 'NONE', *, *, #68804, .T. ) ; +#72381 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#72383 = AXIS2_PLACEMENT_3D ( 'NONE', #12621, #43830, #74988 ) ; +#72382 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48255, 'distance_accuracy_value', 'NONE'); +#72384 = PRESENTATION_STYLE_ASSIGNMENT (( #19787 ) ) ; +#72385 = CARTESIAN_POINT ( 'NONE', ( 1.417810389965429962, -1.053930089500670020, 0.8100000000000000533 ) ) ; +#72386 = VERTEX_POINT ( 'NONE', #16000 ) ; +#72387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50993 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71721, #48256, #86021 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72388 = EDGE_CURVE ( 'NONE', #19901, #74424, #695, .T. ) ; +#72389 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#72390 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44676 ), #2318 ) ; +#72391 = ORIENTED_EDGE ( 'NONE', *, *, #80871, .F. ) ; +#72392 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72393 = ORIENTED_EDGE ( 'NONE', *, *, #7344, .T. ) ; +#72394 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72395 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88733 ), #11973 ) ; +#72396 = ORIENTED_EDGE ( 'NONE', *, *, #31071, .F. ) ; +#72397 = ORIENTED_EDGE ( 'NONE', *, *, #80152, .F. ) ; +#72398 = VECTOR ( 'NONE', #49679, 1000.000000000000000 ) ; +#72399 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#72400 = VERTEX_POINT ( 'NONE', #45606 ) ; +#72401 = VECTOR ( 'NONE', #19905, 1000.000000000000000 ) ; +#72402 = LINE ( 'NONE', #72929, #12237 ) ; +#72403 = FACE_OUTER_BOUND ( 'NONE', #27052, .T. ) ; +#72404 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63109 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87002, #2244, #80866 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72405 = CARTESIAN_POINT ( 'NONE', ( -0.2758995662929830117, -0.9966931238414048488, 0.8299999999999999600 ) ) ; +#72406 = PRESENTATION_STYLE_ASSIGNMENT (( #16751 ) ) ; +#72407 = ORIENTED_EDGE ( 'NONE', *, *, #9020, .F. ) ; +#72408 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85454 ) ) ; +#72409 = FILL_AREA_STYLE_COLOUR ( '', #82013 ) ; +#72410 = ORIENTED_EDGE ( 'NONE', *, *, #10805, .F. ) ; +#72411 = EDGE_LOOP ( 'NONE', ( #967, #35366, #16091, #21532 ) ) ; +#72412 = LINE ( 'NONE', #93846, #90581 ) ; +#72413 = PRESENTATION_STYLE_ASSIGNMENT (( #27496 ) ) ; +#72414 = VECTOR ( 'NONE', #29666, 1000.000000000000000 ) ; +#72415 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999460114 ) ) ; +#72416 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12610, #41832, #42339, #74978, #57173, #3020, #19332, #88291, #97414, #66315, #18304 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000017764, 0.3750000000000016653, 0.5000000000000015543, 0.7500000000000007772, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#72417 = STYLED_ITEM ( 'NONE', ( #79459 ), #72247 ) ; +#72419 = EDGE_CURVE ( 'NONE', #47067, #27614, #38008, .T. ) ; +#72418 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#72420 = FILL_AREA_STYLE_COLOUR ( '', #39555 ) ; +#72421 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#72422 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5468, 'distance_accuracy_value', 'NONE'); +#72423 = SURFACE_SIDE_STYLE ('',( #9063 ) ) ; +#72424 = ORIENTED_EDGE ( 'NONE', *, *, #15116, .T. ) ; +#72425 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8648700000000000276 ) ) ; +#72426 = CARTESIAN_POINT ( 'NONE', ( 0.02260986327491390155, -1.199770973383029959, 0.8299999999999999600 ) ) ; +#72427 = VERTEX_POINT ( 'NONE', #84954 ) ; +#72428 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87168 ), #48031 ) ; +#72429 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72430 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -0.9000000000000007994, -0.02000000000000000042 ) ) ; +#72431 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72432 = ADVANCED_FACE ( 'NONE', ( #54334 ), #77807, .T. ) ; +#72433 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72434 = FILL_AREA_STYLE_COLOUR ( '', #69523 ) ; +#72435 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#72436 = SURFACE_SIDE_STYLE ('',( #42331 ) ) ; +#72437 = SURFACE_STYLE_FILL_AREA ( #56667 ) ; +#72438 = EDGE_CURVE ( 'NONE', #93936, #100590, #70132, .T. ) ; +#72439 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72440 = STYLED_ITEM ( 'NONE', ( #88912 ), #88527 ) ; +#72441 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72442 = FILL_AREA_STYLE ('',( #72967 ) ) ; +#72443 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72444 = FILL_AREA_STYLE_COLOUR ( '', #67720 ) ; +#72445 = ADVANCED_FACE ( 'NONE', ( #92107 ), #31845, .T. ) ; +#72446 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43078 ), #54552 ) ; +#72447 = VECTOR ( 'NONE', #30521, 1000.000000000000000 ) ; +#72448 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#72449 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.8999999999999999112, 0.000000000000000000 ) ) ; +#72450 = VECTOR ( 'NONE', #19777, 1000.000000000000000 ) ; +#72451 = LINE ( 'NONE', #54652, #69850 ) ; +#72452 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72453 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#72454 = ADVANCED_FACE ( 'NONE', ( #41541 ), #80350, .F. ) ; +#72455 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17055 ) ) ; +#72457 = ORIENTED_EDGE ( 'NONE', *, *, #35139, .T. ) ; +#72456 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82260 ) ) ; +#72458 = SURFACE_SIDE_STYLE ('',( #41350 ) ) ; +#72459 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58874, 'distance_accuracy_value', 'NONE'); +#72460 = ORIENTED_EDGE ( 'NONE', *, *, #32769, .T. ) ; +#72462 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43916, 'distance_accuracy_value', 'NONE'); +#72461 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72463 = EDGE_CURVE ( 'NONE', #92782, #84842, #95616, .T. ) ; +#72465 = VECTOR ( 'NONE', #22720, 1000.000000000000114 ) ; +#72464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50171 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63637, #25839, #32977 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72466 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72467 = FACE_OUTER_BOUND ( 'NONE', #72754, .T. ) ; +#72468 = CARTESIAN_POINT ( 'NONE', ( 1.726111644763860253, -0.9656914468017120390, 0.8100000000000006084 ) ) ; +#72469 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43171 ) ) ; +#72470 = EDGE_CURVE ( 'NONE', #69178, #88062, #87993, .T. ) ; +#72471 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#72472 = ORIENTED_EDGE ( 'NONE', *, *, #89288, .F. ) ; +#72473 = ADVANCED_FACE ( 'NONE', ( #80858 ), #33897, .T. ) ; +#72474 = VERTEX_POINT ( 'NONE', #79333 ) ; +#72475 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72476 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25935, 'distance_accuracy_value', 'NONE'); +#72477 = VECTOR ( 'NONE', #65758, 1000.000000000000000 ) ; +#72478 = FILL_AREA_STYLE ('',( #24562 ) ) ; +#72479 = LINE ( 'NONE', #64834, #31923 ) ; +#72480 = FILL_AREA_STYLE ('',( #57719 ) ) ; +#72481 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#72482 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69182 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2620, #71566, #24630 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72483 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#72484 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72485 = VERTEX_POINT ( 'NONE', #55857 ) ; +#72486 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #16469 ) ) ; +#72487 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72488 = LINE ( 'NONE', #16825, #57624 ) ; +#72489 = VERTEX_POINT ( 'NONE', #88497 ) ; +#72490 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#72491 = AXIS2_PLACEMENT_3D ( 'NONE', #24321, #6507, #77019 ) ; +#72492 = PLANE ( 'NONE', #16073 ) ; +#72493 = ORIENTED_EDGE ( 'NONE', *, *, #78944, .F. ) ; +#72494 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38202 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45121, #23193, #84459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72496 = PRESENTATION_STYLE_ASSIGNMENT (( #17861 ) ) ; +#72497 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72498 = PRESENTATION_STYLE_ASSIGNMENT (( #88333 ) ) ; +#72499 = SURFACE_STYLE_USAGE ( .BOTH. , #41388 ) ; +#72500 = CARTESIAN_POINT ( 'NONE', ( 13.14297600000000088, 10.06576599999999999, 0.8991599999999999593 ) ) ; +#72501 = PRESENTATION_STYLE_ASSIGNMENT (( #24584 ) ) ; +#72502 = EDGE_CURVE ( 'NONE', #80272, #86316, #94094, .T. ) ; +#72503 = SURFACE_STYLE_USAGE ( .BOTH. , #64351 ) ; +#72504 = FACE_OUTER_BOUND ( 'NONE', #34100, .T. ) ; +#72507 = ORIENTED_EDGE ( 'NONE', *, *, #4656, .T. ) ; +#72506 = VERTEX_POINT ( 'NONE', #86481 ) ; +#72505 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57914 ) ) ; +#72508 = ORIENTED_EDGE ( 'NONE', *, *, #25103, .T. ) ; +#72509 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72510 = VECTOR ( 'NONE', #3552, 1000.000000000000000 ) ; +#72511 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#72512 = ORIENTED_EDGE ( 'NONE', *, *, #23671, .T. ) ; +#72513 = ADVANCED_FACE ( 'NONE', ( #72172 ), #24223, .T. ) ; +#72514 = ORIENTED_EDGE ( 'NONE', *, *, #1230, .T. ) ; +#72515 = SURFACE_STYLE_USAGE ( .BOTH. , #65356 ) ; +#72516 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72517 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155856999999999690, 0.8991599999999999593 ) ) ; +#72518 = LINE ( 'NONE', #93455, #60152 ) ; +#72520 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72519 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, 0.000000000000000000 ) ) ; +#72521 = FACE_OUTER_BOUND ( 'NONE', #23313, .T. ) ; +#72522 = EDGE_LOOP ( 'NONE', ( #46655, #34127, #29074, #31944 ) ) ; +#72523 = EDGE_CURVE ( 'NONE', #40659, #81709, #18710, .T. ) ; +#72524 = ORIENTED_EDGE ( 'NONE', *, *, #81196, .F. ) ; +#72525 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42105 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21373, #84658, #38706 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72526 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72527 = ORIENTED_EDGE ( 'NONE', *, *, #96862, .T. ) ; +#72528 = EDGE_CURVE ( 'NONE', #23447, #100135, #12311, .T. ) ; +#72530 = ORIENTED_EDGE ( 'NONE', *, *, #100589, .T. ) ; +#72529 = SURFACE_STYLE_USAGE ( .BOTH. , #40409 ) ; +#72531 = CIRCLE ( 'NONE', #51351, 0.04999999999999969746 ) ; +#72532 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22020 ), #48134 ) ; +#72533 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#72534 = PLANE ( 'NONE', #97737 ) ; +#72535 = VERTEX_POINT ( 'NONE', #35901 ) ; +#72537 = CARTESIAN_POINT ( 'NONE', ( -0.02839774098039829844, -1.241062917987890257, 0.8299999999999999600 ) ) ; +#72536 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1222 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59337, #60820, #76113 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72538 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72539 = ORIENTED_EDGE ( 'NONE', *, *, #37659, .F. ) ; +#72540 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 9.350000000000001421, 0.03429000000000000103 ) ) ; +#72542 = STYLED_ITEM ( 'NONE', ( #72413 ), #27195 ) ; +#72541 = VECTOR ( 'NONE', #67983, 1000.000000000000000 ) ; +#72543 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72544 = AXIS2_PLACEMENT_3D ( 'NONE', #57948, #49769, #66072 ) ; +#72545 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#72547 = EDGE_CURVE ( 'NONE', #13350, #2068, #43525, .T. ) ; +#72546 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#72548 = EDGE_CURVE ( 'NONE', #40281, #24251, #35413, .T. ) ; +#72549 = SURFACE_STYLE_USAGE ( .BOTH. , #86876 ) ; +#72550 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.500000000000000000, 0.000000000000000000 ) ) ; +#72551 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72552 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#72553 = ORIENTED_EDGE ( 'NONE', *, *, #17224, .T. ) ; +#72554 = FILL_AREA_STYLE ('',( #87878 ) ) ; +#72555 = CARTESIAN_POINT ( 'NONE', ( -0.9392372690293679938, -1.031612284007709990, 0.8300000000000000711 ) ) ; +#72556 = ORIENTED_EDGE ( 'NONE', *, *, #47749, .T. ) ; +#72557 = AXIS2_PLACEMENT_3D ( 'NONE', #61624, #47792, #47277 ) ; +#72558 = LINE ( 'NONE', #82742, #95292 ) ; +#72559 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72561 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#72560 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2750000000000000222, 0.1500000000000000500 ) ) ; +#72562 = DIRECTION ( 'NONE', ( 0.9200319872051138104, 0.3918432626949318598, 0.000000000000000000 ) ) ; +#72563 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#72564 = EDGE_CURVE ( 'NONE', #17994, #26462, #69694, .T. ) ; +#72565 = EDGE_CURVE ( 'NONE', #31464, #13386, #40439, .T. ) ; +#72566 = STYLED_ITEM ( 'NONE', ( #36494 ), #68189 ) ; +#72567 = ADVANCED_FACE ( 'NONE', ( #98565 ), #82355, .T. ) ; +#72568 = STYLED_ITEM ( 'NONE', ( #569 ), #72678 ) ; +#72569 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72570 = VERTEX_POINT ( 'NONE', #75196 ) ; +#72572 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72571 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72573 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#72574 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#72575 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72576 = AXIS2_PLACEMENT_3D ( 'NONE', #40818, #81135, #11072 ) ; +#72577 = SURFACE_STYLE_FILL_AREA ( #2153 ) ; +#72578 = ORIENTED_EDGE ( 'NONE', *, *, #15030, .F. ) ; +#72579 = SURFACE_STYLE_FILL_AREA ( #89915 ) ; +#72580 = AXIS2_PLACEMENT_3D ( 'NONE', #20771, #11013, #58111 ) ; +#72581 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72582 = CARTESIAN_POINT ( 'NONE', ( 9.507386875125000358, 6.971254875125000083, 0.8648700000000000276 ) ) ; +#72583 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#72584 = ADVANCED_FACE ( 'NONE', ( #36388 ), #59904, .T. ) ; +#72585 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3568 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25098, #74043, #65886 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72586 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35095 ) ) ; +#72587 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8199999999999999512 ) ) ; +#72588 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.499999999999960032, 0.1829999999999999960 ) ) ; +#72590 = PRESENTATION_STYLE_ASSIGNMENT (( #33817 ) ) ; +#72589 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4229, #57903, #60273 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72591 = FILL_AREA_STYLE ('',( #89431 ) ) ; +#72592 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #22581 ) ; +#72593 = SURFACE_STYLE_FILL_AREA ( #64445 ) ; +#72594 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51700, 'distance_accuracy_value', 'NONE'); +#72595 = EDGE_CURVE ( 'NONE', #88475, #22813, #28315, .T. ) ; +#72596 = SURFACE_SIDE_STYLE ('',( #79781 ) ) ; +#72597 = VECTOR ( 'NONE', #96480, 1000.000000000000000 ) ; +#72598 = LINE ( 'NONE', #16942, #32531 ) ; +#72599 = EDGE_LOOP ( 'NONE', ( #80228, #3485, #58872, #35223 ) ) ; +#72600 = FACE_OUTER_BOUND ( 'NONE', #59869, .T. ) ; +#72601 = ADVANCED_FACE ( 'NONE', ( #92481, #69498 ), #23077, .F. ) ; +#72602 = ORIENTED_EDGE ( 'NONE', *, *, #93764, .T. ) ; +#72603 = SURFACE_STYLE_USAGE ( .BOTH. , #27681 ) ; +#72604 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86392, 'distance_accuracy_value', 'NONE'); +#72605 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32748, 'distance_accuracy_value', 'NONE'); +#72606 = FILL_AREA_STYLE ('',( #9737 ) ) ; +#72607 = PRESENTATION_STYLE_ASSIGNMENT (( #31790 ) ) ; +#72608 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.500000000000000444, 0.000000000000000000 ) ) ; +#72609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72610 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72611 = AXIS2_PLACEMENT_3D ( 'NONE', #94306, #16683, #38698 ) ; +#72612 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, -3.499999999999980016, 0.1829999999999999960 ) ) ; +#72613 = ORIENTED_EDGE ( 'NONE', *, *, #10600, .T. ) ; +#72614 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#72615 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#72617 = VECTOR ( 'NONE', #67147, 1000.000000000000000 ) ; +#72616 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#72618 = ORIENTED_EDGE ( 'NONE', *, *, #71246, .F. ) ; +#72619 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#72620 = STYLED_ITEM ( 'NONE', ( #50157 ), #99251 ) ; +#72621 = CARTESIAN_POINT ( 'NONE', ( 4.670775750250086844, 8.852158750250087138, 0.8991599999999999593 ) ) ; +#72622 = PRESENTATION_STYLE_ASSIGNMENT (( #27696 ) ) ; +#72623 = ORIENTED_EDGE ( 'NONE', *, *, #80206, .T. ) ; +#72624 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #21624, #44577, #82430, #59970, #76240, #27820 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 4 ), + ( 0.000000000000000000, 0.5000000000000002220, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#72625 = CARTESIAN_POINT ( 'NONE', ( 1.876179938779914957, -3.099999999999970335, 0.000000000000000000 ) ) ; +#72626 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59635 ) ) ; +#72627 = PRESENTATION_STYLE_ASSIGNMENT (( #18490 ) ) ; +#72628 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72629 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72630 = EDGE_CURVE ( 'NONE', #91128, #37735, #13830, .T. ) ; +#72631 = SURFACE_STYLE_USAGE ( .BOTH. , #72140 ) ; +#72632 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#72633 = ORIENTED_EDGE ( 'NONE', *, *, #92630, .T. ) ; +#72634 = AXIS2_PLACEMENT_3D ( 'NONE', #34391, #26222, #49197 ) ; +#72635 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72636 = VERTEX_POINT ( 'NONE', #77685 ) ; +#72637 = STYLED_ITEM ( 'NONE', ( #23161 ), #12675 ) ; +#72638 = EDGE_CURVE ( 'NONE', #15485, #66967, #70, .T. ) ; +#72639 = ORIENTED_EDGE ( 'NONE', *, *, #64212, .T. ) ; +#72640 = CARTESIAN_POINT ( 'NONE', ( 1.660250899578611383, -1.164854777894125393, 0.8099999999999998312 ) ) ; +#72641 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72642 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41686 ), #848 ) ; +#72643 = FILL_AREA_STYLE_COLOUR ( '', #41375 ) ; +#72644 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#72645 = LINE ( 'NONE', #3211, #75467 ) ; +#72647 = SURFACE_STYLE_USAGE ( .BOTH. , #80330 ) ; +#72646 = LINE ( 'NONE', #10772, #4016 ) ; +#72648 = ORIENTED_EDGE ( 'NONE', *, *, #57199, .F. ) ; +#72649 = EDGE_CURVE ( 'NONE', #77426, #64866, #23575, .T. ) ; +#72651 = VERTEX_POINT ( 'NONE', #93472 ) ; +#72650 = ORIENTED_EDGE ( 'NONE', *, *, #16798, .F. ) ; +#72652 = FILL_AREA_STYLE_COLOUR ( '', #12309 ) ; +#72653 = EDGE_LOOP ( 'NONE', ( #12029, #21405, #84461, #69829 ) ) ; +#72654 = EDGE_CURVE ( 'NONE', #39650, #89241, #47041, .T. ) ; +#72655 = ORIENTED_EDGE ( 'NONE', *, *, #63899, .F. ) ; +#72656 = ORIENTED_EDGE ( 'NONE', *, *, #96629, .F. ) ; +#72657 = VECTOR ( 'NONE', #65784, 1000.000000000000000 ) ; +#72658 = FILL_AREA_STYLE ('',( #10266 ) ) ; +#72659 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72661 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72660 = VECTOR ( 'NONE', #20452, 1000.000000000000000 ) ; +#72662 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, -8.400000000000000355, -13.35000000000000142 ) ) ; +#72663 = ORIENTED_EDGE ( 'NONE', *, *, #69740, .F. ) ; +#72665 = ADVANCED_FACE ( 'NONE', ( #36887 ), #1865, .T. ) ; +#72664 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72666 = CARTESIAN_POINT ( 'NONE', ( 1.823376623376620209, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#72667 = ORIENTED_EDGE ( 'NONE', *, *, #74430, .T. ) ; +#72668 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46548 ), #41708 ) ; +#72669 = PLANE ( 'NONE', #67764 ) ; +#72670 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#72671 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72672 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92184 ), #4159 ) ; +#72673 = PLANE ( 'NONE', #64375 ) ; +#72674 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 5.267127000000001225, 0.8648700000000000276 ) ) ; +#72676 = CARTESIAN_POINT ( 'NONE', ( -1.325735931288071434, 0.6892893218813451739, 1.100000000000000089 ) ) ; +#72675 = VECTOR ( 'NONE', #93339, 1000.000000000000000 ) ; +#72677 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61261 ), #72245 ) ; +#72678 = ADVANCED_FACE ( 'NONE', ( #78207 ), #2614, .T. ) ; +#72679 = EDGE_CURVE ( 'NONE', #44056, #91128, #49089, .T. ) ; +#72680 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72681 = SURFACE_SIDE_STYLE ('',( #94105 ) ) ; +#72682 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1286 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87725, #2969, #41283 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72683 = SURFACE_STYLE_FILL_AREA ( #80361 ) ; +#72684 = EDGE_CURVE ( 'NONE', #62724, #41373, #94994, .T. ) ; +#72685 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#72686 = EDGE_CURVE ( 'NONE', #39524, #48036, #1087, .T. ) ; +#72687 = SURFACE_STYLE_FILL_AREA ( #48721 ) ; +#72688 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.09999999999999870104, 6.355796620655076481E-79 ) ) ; +#72690 = LINE ( 'NONE', #74200, #81770 ) ; +#72689 = CARTESIAN_POINT ( 'NONE', ( 0.3985040481619670505, -0.9698512957057280337, 0.8100000000000000533 ) ) ; +#72691 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#72692 = CIRCLE ( 'NONE', #51594, 0.5799999999999999600 ) ; +#72693 = EDGE_CURVE ( 'NONE', #88325, #77365, #24621, .T. ) ; +#72694 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15587 ) ) ; +#72695 = CARTESIAN_POINT ( 'NONE', ( -1.069701591823909892, -0.8955552045491339541, 0.8100000000000000533 ) ) ; +#72696 = FILL_AREA_STYLE_COLOUR ( '', #71861 ) ; +#72697 = EDGE_LOOP ( 'NONE', ( #66526, #87481, #66497, #55240, #15959, #26184 ) ) ; +#72698 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72699 = EDGE_CURVE ( 'NONE', #69558, #3181, #49591, .T. ) ; +#72700 = VECTOR ( 'NONE', #64900, 1000.000000000000000 ) ; +#72701 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72702 = LINE ( 'NONE', #11322, #88628 ) ; +#72703 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155857000000000134, 0.8648700000000000276 ) ) ; +#72704 = VECTOR ( 'NONE', #35274, 1000.000000000000000 ) ; +#72705 = VERTEX_POINT ( 'NONE', #42916 ) ; +#72706 = DIRECTION ( 'NONE', ( -0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#72707 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72708 = VECTOR ( 'NONE', #67253, 1000.000000000000000 ) ; +#72709 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72710 = LINE ( 'NONE', #10838, #23509 ) ; +#72711 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87427 ), #49922 ) ; +#72712 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72713 = CARTESIAN_POINT ( 'NONE', ( 6.495110999999999635, 1.851801000000000030, 0.8648700000000000276 ) ) ; +#72714 = ORIENTED_EDGE ( 'NONE', *, *, #36387, .F. ) ; +#72715 = CYLINDRICAL_SURFACE ( 'NONE', #47298, 0.05000000000000012768 ) ; +#72716 = LINE ( 'NONE', #4763, #13040 ) ; +#72717 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#72718 = FACE_OUTER_BOUND ( 'NONE', #91001, .T. ) ; +#72719 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72720 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72722 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#72723 = SURFACE_STYLE_FILL_AREA ( #32924 ) ; +#72724 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41853, 'distance_accuracy_value', 'NONE'); +#72725 = LINE ( 'NONE', #26786, #40931 ) ; +#72726 = CARTESIAN_POINT ( 'NONE', ( 1.102257911893530062, -1.419390247362990021, 0.8299999999999999600 ) ) ; +#72727 = FILL_AREA_STYLE ('',( #57434 ) ) ; +#72728 = LINE ( 'NONE', #17075, #95968 ) ; +#72729 = VERTEX_POINT ( 'NONE', #11672 ) ; +#72730 = EDGE_CURVE ( 'NONE', #1795, #87325, #19428, .T. ) ; +#72731 = VERTEX_POINT ( 'NONE', #80735 ) ; +#72732 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99506, 'distance_accuracy_value', 'NONE'); +#72733 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15031, 'distance_accuracy_value', 'NONE'); +#72734 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000777, 0.1400000000000000133 ) ) ; +#72735 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#72736 = STYLED_ITEM ( 'NONE', ( #45625 ), #83741 ) ; +#72737 = AXIS2_PLACEMENT_3D ( 'NONE', #28654, #77120, #59850 ) ; +#72738 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#72739 = AXIS2_PLACEMENT_3D ( 'NONE', #11699, #52623, #20961 ) ; +#72740 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#72741 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72742 = EDGE_CURVE ( 'NONE', #91193, #8318, #12706, .T. ) ; +#72743 = FILL_AREA_STYLE ('',( #58476 ) ) ; +#72744 = ORIENTED_EDGE ( 'NONE', *, *, #3746, .T. ) ; +#72745 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#72746 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72747 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30530 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41952, #10695, #87892 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72748 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.5000000000000000000, -0.02000000000002233672 ) ) ; +#72749 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69518, 'distance_accuracy_value', 'NONE'); +#72750 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17254 ) ) ; +#72751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72752 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84182 ) ) ; +#72753 = STYLED_ITEM ( 'NONE', ( #6505 ), #49037 ) ; +#72754 = EDGE_LOOP ( 'NONE', ( #26272, #3977, #69440, #79285 ) ) ; +#72755 = LINE ( 'NONE', #49795, #36411 ) ; +#72756 = LINE ( 'NONE', #20116, #79403 ) ; +#72757 = STYLED_ITEM ( 'NONE', ( #1327 ), #77921 ) ; +#72758 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#72759 = PLANE ( 'NONE', #5033 ) ; +#72760 = EDGE_CURVE ( 'NONE', #63125, #15816, #65907, .T. ) ; +#72761 = LINE ( 'NONE', #73279, #2243 ) ; +#72762 = STYLED_ITEM ( 'NONE', ( #86248 ), #61860 ) ; +#72763 = ORIENTED_EDGE ( 'NONE', *, *, #100102, .F. ) ; +#72764 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#72765 = PRESENTATION_STYLE_ASSIGNMENT (( #9875 ) ) ; +#72766 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79129, 'distance_accuracy_value', 'NONE'); +#72767 = SURFACE_STYLE_USAGE ( .BOTH. , #80957 ) ; +#72768 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40192 ) ) ; +#72769 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#72770 = CARTESIAN_POINT ( 'NONE', ( 1.826762951391289969, -1.165682221622120096, 0.8099999999999998312 ) ) ; +#72771 = EDGE_CURVE ( 'NONE', #28296, #47444, #4595, .T. ) ; +#72772 = VERTEX_POINT ( 'NONE', #58776 ) ; +#72773 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72774 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72775 = SURFACE_STYLE_FILL_AREA ( #24832 ) ; +#72776 = SURFACE_STYLE_FILL_AREA ( #95205 ) ; +#72777 = PLANE ( 'NONE', #73950 ) ; +#72778 = CARTESIAN_POINT ( 'NONE', ( -1.331253871539946010, -1.158166114942168257, 0.8099999999998713784 ) ) ; +#72779 = FACE_OUTER_BOUND ( 'NONE', #51, .T. ) ; +#72780 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63029 ) ) ; +#72781 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#72782 = VECTOR ( 'NONE', #29347, 1000.000000000000000 ) ; +#72783 = EDGE_CURVE ( 'NONE', #4099, #28558, #38078, .T. ) ; +#72784 = VERTEX_POINT ( 'NONE', #51105 ) ; +#72786 = ORIENTED_EDGE ( 'NONE', *, *, #55360, .F. ) ; +#72785 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72787 = AXIS2_PLACEMENT_3D ( 'NONE', #11897, #74784, #3332 ) ; +#72788 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72789 = FILL_AREA_STYLE ('',( #72278 ) ) ; +#72790 = EDGE_CURVE ( 'NONE', #34323, #25590, #74062, .T. ) ; +#72791 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666653285, 0.6999999999999999556, 0.000000000000000000 ) ) ; +#72792 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#72793 = EDGE_LOOP ( 'NONE', ( #58886, #2240, #47926, #38970 ) ) ; +#72794 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#72795 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#72796 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72797 = VERTEX_POINT ( 'NONE', #67391 ) ; +#72798 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30329 ), #2697 ) ; +#72800 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.569275000000000198, 0.8648700000000000276 ) ) ; +#72799 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#72801 = ORIENTED_EDGE ( 'NONE', *, *, #5337, .T. ) ; +#72802 = ORIENTED_EDGE ( 'NONE', *, *, #43941, .F. ) ; +#72803 = CARTESIAN_POINT ( 'NONE', ( 1.021992881706803580, -1.158166114942168257, 0.8099999999998901412 ) ) ; +#72804 = EDGE_CURVE ( 'NONE', #51489, #27473, #12188, .T. ) ; +#72806 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725635000000000030, 0.8648700000000000276 ) ) ; +#72805 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.000000000000000000 ) ) ; +#72807 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36940 ), #46677 ) ; +#72808 = VERTEX_POINT ( 'NONE', #97000 ) ; +#72809 = EDGE_CURVE ( 'NONE', #80096, #65363, #90374, .T. ) ; +#72810 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#72811 = EDGE_CURVE ( 'NONE', #38629, #93318, #73061, .T. ) ; +#72812 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#72813 = ORIENTED_EDGE ( 'NONE', *, *, #2017, .F. ) ; +#72814 = ORIENTED_EDGE ( 'NONE', *, *, #100465, .F. ) ; +#72815 = FACE_OUTER_BOUND ( 'NONE', #46119, .T. ) ; +#72817 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72816 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#72818 = CARTESIAN_POINT ( 'NONE', ( -0.9931616945682509856, -1.308270162923429902, 0.8100000000000000533 ) ) ; +#72819 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#72820 = VECTOR ( 'NONE', #30560, 1000.000000000000000 ) ; +#72821 = EDGE_CURVE ( 'NONE', #44158, #78277, #18914, .T. ) ; +#72822 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#72823 = FILL_AREA_STYLE ('',( #26372 ) ) ; +#72824 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99148 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40558, #88006, #71172 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72825 = AXIS2_PLACEMENT_3D ( 'NONE', #10492, #40757, #94824 ) ; +#72826 = SURFACE_STYLE_USAGE ( .BOTH. , #86111 ) ; +#72827 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, 0.000000000000000000 ) ) ; +#72828 = EDGE_CURVE ( 'NONE', #34710, #30679, #59795, .T. ) ; +#72829 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72830 = STYLED_ITEM ( 'NONE', ( #22918 ), #16640 ) ; +#72831 = ORIENTED_EDGE ( 'NONE', *, *, #33743, .T. ) ; +#72832 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, 3.500000000000000444, 0.000000000000000000 ) ) ; +#72833 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#72834 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12395 ) ) ; +#72835 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72836 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#72837 = FILL_AREA_STYLE_COLOUR ( '', #47918 ) ; +#72838 = AXIS2_PLACEMENT_3D ( 'NONE', #59204, #97902, #5968 ) ; +#72839 = AXIS2_PLACEMENT_3D ( 'NONE', #11385, #97213, #97687 ) ; +#72840 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#72841 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72842 = SURFACE_STYLE_USAGE ( .BOTH. , #41705 ) ; +#72843 = CLOSED_SHELL ( 'NONE', ( #51179, #9639, #17787, #71015, #42117, #23160 ) ) ; +#72844 = FILL_AREA_STYLE_COLOUR ( '', #49375 ) ; +#72845 = VERTEX_POINT ( 'NONE', #97971 ) ; +#72846 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27238 ) ) ; +#72847 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#72848 = CYLINDRICAL_SURFACE ( 'NONE', #91849, 0.1000000000000000056 ) ; +#72849 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72850 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16255, 'distance_accuracy_value', 'NONE'); +#72851 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#72852 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#72853 = PRESENTATION_STYLE_ASSIGNMENT (( #65687 ) ) ; +#72854 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5527 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48899, #87188, #2431 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72855 = LINE ( 'NONE', #71848, #25526 ) ; +#72856 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#72857 = STYLED_ITEM ( 'NONE', ( #81859 ), #14294 ) ; +#72858 = FILL_AREA_STYLE_COLOUR ( '', #50054 ) ; +#72859 = LINE ( 'NONE', #34579, #37400 ) ; +#72860 = LINE ( 'NONE', #74367, #4772 ) ; +#72861 = VECTOR ( 'NONE', #71679, 1000.000000000000000 ) ; +#72862 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#72864 = FILL_AREA_STYLE_COLOUR ( '', #74 ) ; +#72863 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20652 ) ) ; +#72865 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#72866 = PRESENTATION_STYLE_ASSIGNMENT (( #90170 ) ) ; +#72868 = EDGE_CURVE ( 'NONE', #26606, #45524, #43913, .T. ) ; +#72867 = PLANE ( 'NONE', #24339 ) ; +#72869 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72870 = ORIENTED_EDGE ( 'NONE', *, *, #66687, .T. ) ; +#72871 = SURFACE_STYLE_USAGE ( .BOTH. , #66211 ) ; +#72872 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85487, 'distance_accuracy_value', 'NONE'); +#72873 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14105, 'distance_accuracy_value', 'NONE'); +#72874 = LINE ( 'NONE', #71872, #69879 ) ; +#72875 = STYLED_ITEM ( 'NONE', ( #79628 ), #73854 ) ; +#72876 = FILL_AREA_STYLE_COLOUR ( '', #17761 ) ; +#72877 = LINE ( 'NONE', #10470, #9203 ) ; +#72878 = VERTEX_POINT ( 'NONE', #65375 ) ; +#72879 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#72880 = FILL_AREA_STYLE ('',( #78509 ) ) ; +#72881 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63544, 'distance_accuracy_value', 'NONE'); +#72883 = CYLINDRICAL_SURFACE ( 'NONE', #16809, 0.05000000000000012768 ) ; +#72882 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81069 ) ) ; +#72884 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95655 ) ) ; +#72885 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49459, 'distance_accuracy_value', 'NONE'); +#72886 = SURFACE_STYLE_FILL_AREA ( #11512 ) ; +#72887 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64716 ), #28848 ) ; +#72888 = ADVANCED_FACE ( 'NONE', ( #51617 ), #5078, .T. ) ; +#72889 = ORIENTED_EDGE ( 'NONE', *, *, #95179, .F. ) ; +#72890 = ORIENTED_EDGE ( 'NONE', *, *, #62959, .F. ) ; +#72891 = LINE ( 'NONE', #57605, #5069 ) ; +#72892 = ORIENTED_EDGE ( 'NONE', *, *, #18438, .T. ) ; +#72893 = FACE_OUTER_BOUND ( 'NONE', #20248, .T. ) ; +#72894 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.699999999999999734, 3.364833505069654667E-79 ) ) ; +#72895 = CARTESIAN_POINT ( 'NONE', ( -1.371243692415410331, -1.052663393014950044, 0.8299999999999997380 ) ) ; +#72896 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95672 ), #95736 ) ; +#72897 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #59983 ) ; +#72898 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#72899 = PRESENTATION_STYLE_ASSIGNMENT (( #41759 ) ) ; +#72901 = EDGE_LOOP ( 'NONE', ( #35780, #35650, #5680, #62645 ) ) ; +#72900 = ORIENTED_EDGE ( 'NONE', *, *, #69193, .F. ) ; +#72902 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90824 ) ) ; +#72903 = ORIENTED_EDGE ( 'NONE', *, *, #95827, .F. ) ; +#72904 = ORIENTED_EDGE ( 'NONE', *, *, #3111, .F. ) ; +#72905 = PLANE ( 'NONE', #54026 ) ; +#72906 = AXIS2_PLACEMENT_3D ( 'NONE', #77347, #100712, #30889 ) ; +#72907 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54926 ) ) ; +#72908 = FILL_AREA_STYLE_COLOUR ( '', #55564 ) ; +#72909 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15508 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72487, #58227, #51052 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72910 = CARTESIAN_POINT ( 'NONE', ( 0.5232566677822769741, -0.9829422030519651132, 0.8100000000000000533 ) ) ; +#72911 = ORIENTED_EDGE ( 'NONE', *, *, #69513, .T. ) ; +#72912 = CLOSED_SHELL ( 'NONE', ( #91464, #52190, #55451, #18948, #38092, #51987 ) ) ; +#72913 = EDGE_CURVE ( 'NONE', #45115, #13692, #44884, .T. ) ; +#72914 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2176 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50877, #5348, #83007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72915 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#72916 = ORIENTED_EDGE ( 'NONE', *, *, #62917, .T. ) ; +#72917 = ORIENTED_EDGE ( 'NONE', *, *, #50089, .F. ) ; +#72919 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72918 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#72920 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#72921 = ORIENTED_EDGE ( 'NONE', *, *, #40003, .T. ) ; +#72922 = ORIENTED_EDGE ( 'NONE', *, *, #75041, .F. ) ; +#72923 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#72924 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43469 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85716, #47938, #16246 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#72925 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72926 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#72927 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.100000000000000089, 0.1829999999999619709 ) ) ; +#72928 = ORIENTED_EDGE ( 'NONE', *, *, #66050, .F. ) ; +#72929 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#72930 = EDGE_CURVE ( 'NONE', #53318, #11778, #36767, .T. ) ; +#72931 = ORIENTED_EDGE ( 'NONE', *, *, #6682, .T. ) ; +#72932 = CARTESIAN_POINT ( 'NONE', ( -0.2475423460550890131, -0.9531265814360270205, 0.8299999999999999600 ) ) ; +#72933 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#72934 = ORIENTED_EDGE ( 'NONE', *, *, #100836, .F. ) ; +#72935 = FILL_AREA_STYLE ('',( #41798 ) ) ; +#72936 = PRESENTATION_STYLE_ASSIGNMENT (( #64765 ) ) ; +#72937 = EDGE_LOOP ( 'NONE', ( #7687, #33429, #23435, #32824 ) ) ; +#72938 = ORIENTED_EDGE ( 'NONE', *, *, #50981, .T. ) ; +#72940 = LINE ( 'NONE', #87238, #22589 ) ; +#72939 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72941 = SURFACE_STYLE_USAGE ( .BOTH. , #26491 ) ; +#72942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72943 = AXIS2_PLACEMENT_3D ( 'NONE', #86120, #94771, #47324 ) ; +#72944 = LINE ( 'NONE', #64773, #60848 ) ; +#72945 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#72946 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64776 ), #20750 ) ; +#72947 = ORIENTED_EDGE ( 'NONE', *, *, #50011, .T. ) ; +#72948 = CARTESIAN_POINT ( 'NONE', ( -0.001323334233439310212, -1.190451802854979979, 0.8299999999999999600 ) ) ; +#72949 = ORIENTED_EDGE ( 'NONE', *, *, #58156, .T. ) ; +#72950 = LINE ( 'NONE', #79624, #78218 ) ; +#72951 = FILL_AREA_STYLE ('',( #48983 ) ) ; +#72952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#72953 = CARTESIAN_POINT ( 'NONE', ( 8.231457000000000690, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#72954 = STYLED_ITEM ( 'NONE', ( #68912 ), #84106 ) ; +#72955 = STYLED_ITEM ( 'NONE', ( #35574 ), #91030 ) ; +#72956 = PRESENTATION_STYLE_ASSIGNMENT (( #43309 ) ) ; +#72957 = SURFACE_STYLE_FILL_AREA ( #26010 ) ; +#72958 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#72959 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -13.54999999999999893 ) ) ; +#72960 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#72962 = ORIENTED_EDGE ( 'NONE', *, *, #99127, .F. ) ; +#72961 = VECTOR ( 'NONE', #21107, 1000.000000000000114 ) ; +#72963 = PRESENTATION_STYLE_ASSIGNMENT (( #34687 ) ) ; +#72964 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.016666666666666829, 0.000000000000000000 ) ) ; +#72965 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#72966 = LINE ( 'NONE', #35195, #23195 ) ; +#72967 = FILL_AREA_STYLE_COLOUR ( '', #59874 ) ; +#72968 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#72969 = VECTOR ( 'NONE', #26126, 1000.000000000000114 ) ; +#72970 = LINE ( 'NONE', #43322, #62663 ) ; +#72971 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#72972 = VECTOR ( 'NONE', #53457, 1000.000000000000000 ) ; +#72973 = EDGE_CURVE ( 'NONE', #4673, #55200, #76949, .T. ) ; +#72974 = FILL_AREA_STYLE ('',( #18829 ) ) ; +#72975 = VECTOR ( 'NONE', #26144, 1000.000000000000000 ) ; +#72976 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#72977 = VECTOR ( 'NONE', #100583, 1000.000000000000000 ) ; +#72978 = STYLED_ITEM ( 'NONE', ( #24179 ), #16277 ) ; +#72979 = LINE ( 'NONE', #20347, #55166 ) ; +#72980 = STYLED_ITEM ( 'NONE', ( #69301 ), #23308 ) ; +#72981 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33340, 'distance_accuracy_value', 'NONE'); +#72982 = VERTEX_POINT ( 'NONE', #69889 ) ; +#72983 = CLOSED_SHELL ( 'NONE', ( #235, #61405, #1988, #53128, #44016, #79170 ) ) ; +#72984 = PRESENTATION_STYLE_ASSIGNMENT (( #88304 ) ) ; +#72986 = ADVANCED_FACE ( 'NONE', ( #30082 ), #45384, .T. ) ; +#72985 = CARTESIAN_POINT ( 'NONE', ( 1.549517223800989996, -0.9663557550577259736, 0.8100000000000000533 ) ) ; +#72987 = VERTEX_POINT ( 'NONE', #76552 ) ; +#72988 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#72990 = VECTOR ( 'NONE', #94905, 1000.000000000000114 ) ; +#72989 = SURFACE_SIDE_STYLE ('',( #80665 ) ) ; +#72991 = CARTESIAN_POINT ( 'NONE', ( -0.1450079136436681349, -1.164927051866627927, 0.8299999999999999600 ) ) ; +#72992 = STYLED_ITEM ( 'NONE', ( #51676 ), #60138 ) ; +#72993 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000000295, 0.8648700000000000276 ) ) ; +#72994 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#72995 = STYLED_ITEM ( 'NONE', ( #93721 ), #14924 ) ; +#72996 = LINE ( 'NONE', #48526, #35200 ) ; +#72997 = EDGE_LOOP ( 'NONE', ( #38728, #13131, #39748, #98453 ) ) ; +#72998 = ORIENTED_EDGE ( 'NONE', *, *, #46431, .T. ) ; +#72999 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#73000 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73001 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20485 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86668, #78494, #85139 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73002 = SURFACE_STYLE_USAGE ( .BOTH. , #74005 ) ; +#73003 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73004 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#73005 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73006 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73007 = LINE ( 'NONE', #27565, #28867 ) ; +#73008 = EDGE_CURVE ( 'NONE', #87567, #100106, #29110, .T. ) ; +#73009 = ORIENTED_EDGE ( 'NONE', *, *, #97253, .T. ) ; +#73010 = AXIS2_PLACEMENT_3D ( 'NONE', #1572, #55709, #48550 ) ; +#73011 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#73012 = VERTEX_POINT ( 'NONE', #99930 ) ; +#73013 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#73014 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58401 ), #82773 ) ; +#73015 = SURFACE_STYLE_USAGE ( .BOTH. , #41878 ) ; +#73016 = ADVANCED_FACE ( 'NONE', ( #6050 ), #100421, .T. ) ; +#73017 = FILL_AREA_STYLE ('',( #56207 ) ) ; +#73018 = SURFACE_STYLE_FILL_AREA ( #19892 ) ; +#73019 = CARTESIAN_POINT ( 'NONE', ( 3.193541999999999881, 13.79677200000000070, 0.8991599999999999593 ) ) ; +#73020 = PRESENTATION_STYLE_ASSIGNMENT (( #10627 ) ) ; +#73021 = FILL_AREA_STYLE_COLOUR ( '', #107 ) ; +#73022 = PRESENTATION_STYLE_ASSIGNMENT (( #18872 ) ) ; +#73024 = VERTEX_POINT ( 'NONE', #47438 ) ; +#73023 = ORIENTED_EDGE ( 'NONE', *, *, #63790, .F. ) ; +#73025 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#73026 = ORIENTED_EDGE ( 'NONE', *, *, #91343, .F. ) ; +#73027 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73028 = FILL_AREA_STYLE ('',( #51077 ) ) ; +#73029 = ORIENTED_EDGE ( 'NONE', *, *, #1726, .F. ) ; +#73030 = EDGE_CURVE ( 'NONE', #90877, #7315, #39781, .T. ) ; +#73031 = VECTOR ( 'NONE', #35214, 1000.000000000000000 ) ; +#73032 = ORIENTED_EDGE ( 'NONE', *, *, #19902, .F. ) ; +#73033 = PLANE ( 'NONE', #28581 ) ; +#73034 = PLANE ( 'NONE', #13656 ) ; +#73035 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, -3.149999999999959499, 0.000000000000000000 ) ) ; +#73036 = STYLED_ITEM ( 'NONE', ( #1219 ), #79412 ) ; +#73038 = LINE ( 'NONE', #95982, #18900 ) ; +#73037 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.149999999999970157, 0.000000000000000000 ) ) ; +#73039 = FILL_AREA_STYLE_COLOUR ( '', #93095 ) ; +#73040 = ORIENTED_EDGE ( 'NONE', *, *, #97864, .T. ) ; +#73041 = ORIENTED_EDGE ( 'NONE', *, *, #36166, .T. ) ; +#73042 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73043 = VERTEX_POINT ( 'NONE', #95374 ) ; +#73044 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50442 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83969, #5816, #21679 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73045 = STYLED_ITEM ( 'NONE', ( #63941 ), #24636 ) ; +#73046 = VECTOR ( 'NONE', #42841, 1000.000000000000000 ) ; +#73048 = ORIENTED_EDGE ( 'NONE', *, *, #67276, .F. ) ; +#73047 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6999999999999999556, -13.15000000000000036 ) ) ; +#73049 = STYLED_ITEM ( 'NONE', ( #27173 ), #41558 ) ; +#73050 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73051 = EDGE_CURVE ( 'NONE', #24413, #10654, #93351, .T. ) ; +#73052 = SURFACE_STYLE_FILL_AREA ( #41914 ) ; +#73053 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999993650, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#73055 = STYLED_ITEM ( 'NONE', ( #5403 ), #23452 ) ; +#73054 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73056 = EDGE_LOOP ( 'NONE', ( #77664, #53075, #100809, #40086 ) ) ; +#73057 = LINE ( 'NONE', #3610, #22392 ) ; +#73058 = CLOSED_SHELL ( 'NONE', ( #12025, #7132, #98818, #42647, #72888, #18119 ) ) ; +#73059 = VERTEX_POINT ( 'NONE', #16252 ) ; +#73060 = PRESENTATION_STYLE_ASSIGNMENT (( #23200 ) ) ; +#73061 = LINE ( 'NONE', #43413, #5690 ) ; +#73062 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73063 = LINE ( 'NONE', #64895, #79216 ) ; +#73064 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73066 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#73065 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2955 ), #42097 ) ; +#73067 = EDGE_CURVE ( 'NONE', #56583, #76014, #50231, .T. ) ; +#73068 = PRESENTATION_STYLE_ASSIGNMENT (( #10163 ) ) ; +#73069 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.8500000000100800257, 0.6499230723517829267 ) ) ; +#73070 = AXIS2_PLACEMENT_3D ( 'NONE', #80998, #17654, #41180 ) ; +#73071 = ORIENTED_EDGE ( 'NONE', *, *, #16098, .T. ) ; +#73072 = CARTESIAN_POINT ( 'NONE', ( 1.508691354424570141, -1.396584910994120188, 0.8099999999999982769 ) ) ; +#73073 = CARTESIAN_POINT ( 'NONE', ( -1.111006624335320048, -0.8869042198941200494, 0.8300000000000000711 ) ) ; +#73074 = VERTEX_POINT ( 'NONE', #24992 ) ; +#73075 = FILL_AREA_STYLE_COLOUR ( '', #92098 ) ; +#73076 = VECTOR ( 'NONE', #22624, 1000.000000000000000 ) ; +#73077 = CARTESIAN_POINT ( 'NONE', ( -0.4703841191077399730, -1.247659769119729978, 0.8300000000000000711 ) ) ; +#73079 = LINE ( 'NONE', #3132, #93129 ) ; +#73078 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#73080 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73081 = FACE_OUTER_BOUND ( 'NONE', #30818, .T. ) ; +#73082 = AXIS2_PLACEMENT_3D ( 'NONE', #43527, #27748, #74696 ) ; +#73083 = SURFACE_SIDE_STYLE ('',( #7303 ) ) ; +#73084 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#73085 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32425, #93143, #1793 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73086 = VECTOR ( 'NONE', #56239, 1000.000000000000000 ) ; +#73087 = LINE ( 'NONE', #73591, #72660 ) ; +#73088 = ORIENTED_EDGE ( 'NONE', *, *, #77647, .F. ) ; +#73089 = STYLED_ITEM ( 'NONE', ( #83882 ), #31322 ) ; +#73090 = EDGE_CURVE ( 'NONE', #95596, #57504, #48937, .T. ) ; +#73092 = FILL_AREA_STYLE_COLOUR ( '', #34760 ) ; +#73091 = LINE ( 'NONE', #82273, #3512 ) ; +#73093 = FACE_OUTER_BOUND ( 'NONE', #92503, .T. ) ; +#73094 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#73095 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77969 ), #30712 ) ; +#73096 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79595 ) ) ; +#73097 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55196 ), #1303 ) ; +#73098 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49446, 'distance_accuracy_value', 'NONE'); +#73099 = ORIENTED_EDGE ( 'NONE', *, *, #34678, .T. ) ; +#73100 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#73101 = EDGE_CURVE ( 'NONE', #59629, #49689, #973, .T. ) ; +#73102 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73103 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73104 = CARTESIAN_POINT ( 'NONE', ( -1.038413249809780003, -1.000241703689469963, 0.8299999999999999600 ) ) ; +#73105 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#73106 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73107 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#73108 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#73109 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73110 = EDGE_CURVE ( 'NONE', #38776, #87602, #9054, .T. ) ; +#73111 = LINE ( 'NONE', #2163, #71942 ) ; +#73112 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #44952, #76126, #6116, #68449 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#73113 = CARTESIAN_POINT ( 'NONE', ( -1.018373906775690063, -1.409018172687890091, 0.8300000000000001821 ) ) ; +#73114 = SURFACE_SIDE_STYLE ('',( #72593 ) ) ; +#73115 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97561 ) ) ; +#73116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73117 = ORIENTED_EDGE ( 'NONE', *, *, #79816, .F. ) ; +#73118 = LINE ( 'NONE', #8712, #71010 ) ; +#73119 = EDGE_CURVE ( 'NONE', #59518, #30553, #72412, .T. ) ; +#73120 = VERTEX_POINT ( 'NONE', #56646 ) ; +#73121 = SURFACE_STYLE_FILL_AREA ( #89440 ) ; +#73122 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45000, 'distance_accuracy_value', 'NONE'); +#73123 = PRESENTATION_STYLE_ASSIGNMENT (( #64457 ) ) ; +#73124 = SURFACE_SIDE_STYLE ('',( #18470 ) ) ; +#73125 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69734 ) ) ; +#73126 = PLANE ( 'NONE', #3268 ) ; +#73127 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#73128 = VECTOR ( 'NONE', #65348, 1000.000000000000000 ) ; +#73129 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#73130 = SURFACE_STYLE_FILL_AREA ( #65447 ) ; +#73131 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#73132 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81342 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76940, #5435, #85093 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73133 = EDGE_LOOP ( 'NONE', ( #48961, #91676, #5030, #2839 ) ) ; +#73134 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73135 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#73136 = LINE ( 'NONE', #56835, #426 ) ; +#73137 = EDGE_LOOP ( 'NONE', ( #67352, #14877, #9000, #8410 ) ) ; +#73138 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73139 = PLANE ( 'NONE', #19111 ) ; +#73140 = ORIENTED_EDGE ( 'NONE', *, *, #63141, .T. ) ; +#73141 = VECTOR ( 'NONE', #77453, 1000.000000000000114 ) ; +#73142 = ADVANCED_FACE ( 'NONE', ( #94381 ), #94869, .T. ) ; +#73143 = ADVANCED_FACE ( 'NONE', ( #64769 ), #58658, .T. ) ; +#73144 = FACE_OUTER_BOUND ( 'NONE', #63009, .T. ) ; +#73145 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14789, #45940, #61832, #85275 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#73146 = SURFACE_SIDE_STYLE ('',( #57859 ) ) ; +#73147 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74744 ), #92618 ) ; +#73148 = LINE ( 'NONE', #88453, #37722 ) ; +#73149 = CARTESIAN_POINT ( 'NONE', ( -1.529289321881347696, 1.970710678118652082, 0.000000000000000000 ) ) ; +#73150 = LINE ( 'NONE', #27201, #75684 ) ; +#73151 = ORIENTED_EDGE ( 'NONE', *, *, #77421, .F. ) ; +#73153 = AXIS2_PLACEMENT_3D ( 'NONE', #44447, #21990, #60828 ) ; +#73152 = SURFACE_STYLE_USAGE ( .BOTH. , #43492 ) ; +#73154 = ORIENTED_EDGE ( 'NONE', *, *, #68417, .F. ) ; +#73155 = CARTESIAN_POINT ( 'NONE', ( 0.2166666666666670071, -3.099999999999980549, 0.000000000000000000 ) ) ; +#73156 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96007, 'distance_accuracy_value', 'NONE'); +#73157 = PRESENTATION_STYLE_ASSIGNMENT (( #80832 ) ) ; +#73158 = EDGE_CURVE ( 'NONE', #27634, #28269, #89752, .T. ) ; +#73159 = EDGE_LOOP ( 'NONE', ( #17243, #45980, #7024, #51241 ) ) ; +#73160 = EDGE_CURVE ( 'NONE', #7596, #1063, #63599, .T. ) ; +#73161 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#73162 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73163 = SURFACE_STYLE_USAGE ( .BOTH. , #8751 ) ; +#73164 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#73165 = FILL_AREA_STYLE ('',( #72643 ) ) ; +#73166 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#73167 = STYLED_ITEM ( 'NONE', ( #37698 ), #32212 ) ; +#73168 = CYLINDRICAL_SURFACE ( 'NONE', #47694, 0.05000000000000012768 ) ; +#73169 = AXIS2_PLACEMENT_3D ( 'NONE', #11542, #74929, #74434 ) ; +#73170 = CARTESIAN_POINT ( 'NONE', ( 0.2667602038132769748, -1.009329072279059991, 0.8100000000000000533 ) ) ; +#73171 = ORIENTED_EDGE ( 'NONE', *, *, #39461, .T. ) ; +#73173 = ORIENTED_EDGE ( 'NONE', *, *, #93793, .T. ) ; +#73172 = VERTEX_POINT ( 'NONE', #59168 ) ; +#73174 = SURFACE_STYLE_FILL_AREA ( #42025 ) ; +#73175 = ORIENTED_EDGE ( 'NONE', *, *, #84852, .T. ) ; +#73176 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60146 ) ) ; +#73177 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37813 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19850, #18312, #19340 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73178 = ORIENTED_EDGE ( 'NONE', *, *, #98807, .T. ) ; +#73180 = ORIENTED_EDGE ( 'NONE', *, *, #90416, .T. ) ; +#73179 = FILL_AREA_STYLE_COLOUR ( '', #72143 ) ; +#73181 = VECTOR ( 'NONE', #95424, 1000.000000000000000 ) ; +#73182 = ADVANCED_FACE ( 'NONE', ( #82126 ), #42310, .F. ) ; +#73183 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#73185 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73184 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8100000000000000533 ) ) ; +#73186 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73187 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73188 = ORIENTED_EDGE ( 'NONE', *, *, #93509, .T. ) ; +#73189 = DIRECTION ( 'NONE', ( -0.7071067811865472397, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#73190 = PLANE ( 'NONE', #61495 ) ; +#73191 = ORIENTED_EDGE ( 'NONE', *, *, #31548, .T. ) ; +#73192 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73193 = SURFACE_STYLE_FILL_AREA ( #2738 ) ; +#73194 = VECTOR ( 'NONE', #51058, 1000.000000000000000 ) ; +#73195 = EDGE_CURVE ( 'NONE', #58744, #80432, #73454, .T. ) ; +#73196 = FILL_AREA_STYLE_COLOUR ( '', #83945 ) ; +#73197 = CYLINDRICAL_SURFACE ( 'NONE', #38552, 0.2000000000000005107 ) ; +#73198 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23650 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29130, #98479, #97535 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73199 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43871 ) ) ; +#73200 = EDGE_CURVE ( 'NONE', #29713, #25877, #100307, .T. ) ; +#73201 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73202 = PLANE ( 'NONE', #56546 ) ; +#73203 = VECTOR ( 'NONE', #51405, 1000.000000000000000 ) ; +#73204 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73206 = ADVANCED_FACE ( 'NONE', ( #52476 ), #76953, .T. ) ; +#73205 = LINE ( 'NONE', #25253, #47274 ) ; +#73207 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27583 ) ) ; +#73208 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6277 ), #52001 ) ; +#73209 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22599 ), #56897 ) ; +#73211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73210 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73212 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73213 = FACE_OUTER_BOUND ( 'NONE', #100283, .T. ) ; +#73214 = LINE ( 'NONE', #59427, #32991 ) ; +#73215 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73216 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73217 = ORIENTED_EDGE ( 'NONE', *, *, #41089, .F. ) ; +#73218 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73219 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86235 ) ) ; +#73221 = SURFACE_STYLE_FILL_AREA ( #43056 ) ; +#73222 = ORIENTED_EDGE ( 'NONE', *, *, #28636, .T. ) ; +#73223 = PRESENTATION_STYLE_ASSIGNMENT (( #96155 ) ) ; +#73224 = EDGE_CURVE ( 'NONE', #54246, #67375, #84607, .T. ) ; +#73225 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73227 = SURFACE_STYLE_USAGE ( .BOTH. , #35933 ) ; +#73226 = CYLINDRICAL_SURFACE ( 'NONE', #42575, 0.09999999999999982514 ) ; +#73228 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73229 = FILL_AREA_STYLE ('',( #66541 ) ) ; +#73230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12853 ), #78094 ) ; +#73231 = CARTESIAN_POINT ( 'NONE', ( 0.2414713305586040082, -1.411255840060410049, 0.8299999999999999600 ) ) ; +#73232 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73233 = SURFACE_SIDE_STYLE ('',( #88534 ) ) ; +#73234 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 13.40000000000000036, 0.000000000000000000 ) ) ; +#73235 = ORIENTED_EDGE ( 'NONE', *, *, #94925, .T. ) ; +#73236 = EDGE_CURVE ( 'NONE', #94045, #96104, #14615, .T. ) ; +#73237 = ADVANCED_FACE ( 'NONE', ( #59673 ), #77437, .T. ) ; +#73238 = FILL_AREA_STYLE_COLOUR ( '', #77148 ) ; +#73239 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73240 = SURFACE_STYLE_USAGE ( .BOTH. , #35457 ) ; +#73241 = CARTESIAN_POINT ( 'NONE', ( 1.009265655561859987, -0.9654894655288509542, 0.8299999999999994049 ) ) ; +#73242 = CARTESIAN_POINT ( 'NONE', ( 10.66704100000000111, 4.241823000000000121, 0.8648700000000000276 ) ) ; +#73243 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#73244 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45187 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47240, #78389, #84524 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73245 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57002 ) ) ; +#73246 = LINE ( 'NONE', #65548, #29557 ) ; +#73247 = EDGE_CURVE ( 'NONE', #40880, #9413, #21314, .T. ) ; +#73248 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73249 = SURFACE_STYLE_FILL_AREA ( #26284 ) ; +#73250 = AXIS2_PLACEMENT_3D ( 'NONE', #78511, #914, #32577 ) ; +#73251 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91152 ), #48831 ) ; +#73252 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73253 = FACE_OUTER_BOUND ( 'NONE', #40690, .T. ) ; +#73254 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#73255 = EDGE_LOOP ( 'NONE', ( #16234, #75921, #95507, #52217, #48783, #32607, #84656, #66861, #58381, #52112 ) ) ; +#73256 = PRESENTATION_STYLE_ASSIGNMENT (( #80921 ) ) ; +#73257 = EDGE_CURVE ( 'NONE', #12127, #95078, #75943, .T. ) ; +#73258 = VERTEX_POINT ( 'NONE', #14112 ) ; +#73259 = FILL_AREA_STYLE ('',( #19610 ) ) ; +#73260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40666 ), #48835 ) ; +#73261 = VECTOR ( 'NONE', #50677, 1000.000000000000000 ) ; +#73262 = STYLED_ITEM ( 'NONE', ( #96197 ), #91956 ) ; +#73263 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#73264 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#73265 = VECTOR ( 'NONE', #16665, 1000.000000000000000 ) ; +#73266 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#73267 = VERTEX_POINT ( 'NONE', #6438 ) ; +#73268 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86274 ) ) ; +#73269 = SURFACE_SIDE_STYLE ('',( #91075 ) ) ; +#73270 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73271 = AXIS2_PLACEMENT_3D ( 'NONE', #86518, #31378, #79366 ) ; +#73272 = ORIENTED_EDGE ( 'NONE', *, *, #63356, .F. ) ; +#73273 = EDGE_CURVE ( 'NONE', #51947, #56699, #71817, .T. ) ; +#73274 = ADVANCED_FACE ( 'NONE', ( #48357 ), #38648, .F. ) ; +#73275 = LINE ( 'NONE', #11873, #46775 ) ; +#73276 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73277 = FILL_AREA_STYLE_COLOUR ( '', #21157 ) ; +#73278 = PRESENTATION_STYLE_ASSIGNMENT (( #18614 ) ) ; +#73279 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#73280 = AXIS2_PLACEMENT_3D ( 'NONE', #51523, #96912, #27523 ) ; +#73281 = ORIENTED_EDGE ( 'NONE', *, *, #83770, .F. ) ; +#73282 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73283 = CARTESIAN_POINT ( 'NONE', ( 9.974076750249974310, 3.548858249750026062, 0.8648700000000000276 ) ) ; +#73284 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70031 ), #79835 ) ; +#73285 = PRESENTATION_STYLE_ASSIGNMENT (( #42135 ) ) ; +#73286 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73287 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18998 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97010, #26617, #52610 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73288 = DIRECTION ( 'NONE', ( -0.7071067811865485719, 0.7071067811865465735, 0.000000000000000000 ) ) ; +#73289 = ORIENTED_EDGE ( 'NONE', *, *, #20818, .T. ) ; +#73290 = EDGE_CURVE ( 'NONE', #92361, #21501, #71300, .T. ) ; +#73291 = FACE_OUTER_BOUND ( 'NONE', #65561, .T. ) ; +#73292 = PRESENTATION_STYLE_ASSIGNMENT (( #65106 ) ) ; +#73293 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73294 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73296 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.383333333333333526, 0.000000000000000000 ) ) ; +#73297 = VECTOR ( 'NONE', #93169, 1000.000000000000000 ) ; +#73298 = ORIENTED_EDGE ( 'NONE', *, *, #69280, .F. ) ; +#73300 = ORIENTED_EDGE ( 'NONE', *, *, #79035, .T. ) ; +#73299 = FILL_AREA_STYLE ('',( #42156 ) ) ; +#73301 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76916, 'distance_accuracy_value', 'NONE'); +#73303 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73302 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.000000000000000000 ) ) ; +#73304 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.008431457505076202924, 0.1458578643762690474 ) ) ; +#73305 = DIRECTION ( 'NONE', ( -9.346570452461240360E-17, 1.000000000000000000, -5.551115123125790098E-17 ) ) ; +#73306 = ORIENTED_EDGE ( 'NONE', *, *, #38898, .T. ) ; +#73307 = CARTESIAN_POINT ( 'NONE', ( 1.364996439099779968, -1.475119686261340046, 0.8100000000000010525 ) ) ; +#73308 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#73309 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#73310 = VERTEX_POINT ( 'NONE', #9438 ) ; +#73312 = FACE_OUTER_BOUND ( 'NONE', #100850, .T. ) ; +#73311 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 0.5862888163215710380 ) ) ; +#73313 = EDGE_LOOP ( 'NONE', ( #73442, #1116, #53058, #61841 ) ) ; +#73314 = ORIENTED_EDGE ( 'NONE', *, *, #63601, .T. ) ; +#73315 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8099999999999808464 ) ) ; +#73316 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6314 ) ) ; +#73317 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73319 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#73318 = FACE_OUTER_BOUND ( 'NONE', #95706, .T. ) ; +#73321 = EDGE_CURVE ( 'NONE', #60413, #73926, #56009, .T. ) ; +#73320 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73322 = EDGE_LOOP ( 'NONE', ( #42303, #35631, #52787, #56690, #81362, #71661 ) ) ; +#73323 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58693 ) ) ; +#73324 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000000000888, 0.000000000000000000 ) ) ; +#73325 = ORIENTED_EDGE ( 'NONE', *, *, #20925, .T. ) ; +#73326 = CARTESIAN_POINT ( 'NONE', ( 1.360598746852770047, -1.365766081162230083, 0.8100000000000000533 ) ) ; +#73327 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73328 = EDGE_CURVE ( 'NONE', #91985, #42677, #17657, .T. ) ; +#73329 = ORIENTED_EDGE ( 'NONE', *, *, #28234, .T. ) ; +#73330 = STYLED_ITEM ( 'NONE', ( #84513 ), #81290 ) ; +#73332 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#73331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73333 = CARTESIAN_POINT ( 'NONE', ( -1.371024924951979918, -1.079235908285120171, 0.8100000000000000533 ) ) ; +#73334 = LINE ( 'NONE', #3379, #46499 ) ; +#73335 = STYLED_ITEM ( 'NONE', ( #31641 ), #80703 ) ; +#73336 = LINE ( 'NONE', #96765, #30191 ) ; +#73337 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #48773, #54214, #12831, #55414, #14708, #16980, #10977, #16071, #79587, #84495, #53871, #53369, #17749, #51717, #17252, #50235, #84106, #52541, #50303, #78067, #86619, #21128, #80431, #17089, #16291, #80601, #79765, #19107, #45434, #48538, #87456, #82283, #54040, #79933, #12675, #12155, #80100, #82447, #19622, #18245, #12322, #16455, #53043, #78551, #85433, #52380, #85840, #86963, #17421, #21283, #17647, #17825, #88144, #15559, #16572, #16390, #86275, #19269, #85326, #54568, #85497, #83181, #15901, #78904, #88626, #44940, #48704, #50404, #84432, #89143, #11805, #15394, #20786, #77722, #88977, #87963, #52881, #15099, #15800, #10633, #20448, #49265, #85159, #19459, #50724, #51775, #79425, #13159, #82940, #82767, #83936, #54742, #55071, #84760, #84273, #52053, #45589, #10450, #18758, #50791, #88802, #13317, #46451, #85104, #77894, #16226, #49357, #85941, #17147, #16124, #44289, #85764, #46977, #51218, #84661, #49608, #78243, #85262, #48869, #11982, #49723, #51053, #20272, #12484, #83004, #83446, #14872, #49536, #10811, #50060, #51384, #52228, #53706, #55248, #84990, #46103, #84925, #84606, #20106, #19791, #10295, #82512, #79246, #87795, #52709, #18941, #18602, #52117, #50624, #45109, #19958, #49204, #45774, #84167, #17979, #11476, #84006, #15203, #11308, #21627, #20963, #86453, #80772, #44782, #78719, #46802, #77552, #50464, #12993, #15729, #83618, #83774, #82615, #18077, #53210, #51571, #51879, #18430, #20611, #43967, #17915, #17586, #9968, #54904, #53543, #16906, #82894 ), #28975 ) ; +#73338 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.213428637248479935, 0.8099999999999891731 ) ) ; +#73339 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, 3.149999999999979927, 0.000000000000000000 ) ) ; +#73340 = PRESENTATION_STYLE_ASSIGNMENT (( #88636 ) ) ; +#73341 = CARTESIAN_POINT ( 'NONE', ( 1.306340380209440211, -0.9912247593444889482, 0.8100000000000000533 ) ) ; +#73342 = ORIENTED_EDGE ( 'NONE', *, *, #46598, .T. ) ; +#73343 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73344 = VECTOR ( 'NONE', #88774, 1000.000000000000000 ) ; +#73345 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.300000000000000266, 4.112574283980952083E-79 ) ) ; +#73346 = EDGE_CURVE ( 'NONE', #49449, #52188, #33007, .T. ) ; +#73347 = STYLED_ITEM ( 'NONE', ( #72323 ), #1627 ) ; +#73348 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73349 = LINE ( 'NONE', #34561, #26985 ) ; +#73350 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19241, 'distance_accuracy_value', 'NONE'); +#73351 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60315 ), #70557 ) ; +#73352 = FILL_AREA_STYLE_COLOUR ( '', #45198 ) ; +#73353 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77630 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6332, #30349, #84012 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73354 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#73355 = ORIENTED_EDGE ( 'NONE', *, *, #52766, .T. ) ; +#73356 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#73357 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#73358 = FILL_AREA_STYLE ('',( #67656 ) ) ; +#73359 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73360 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 12.10755799999999915, 0.8648700000000000276 ) ) ; +#73361 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66846 ), #9702 ) ; +#73362 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 5.832812999999999803, 0.8648700000000000276 ) ) ; +#73363 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73364 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#73365 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71751 ) ) ; +#73366 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.01000000000000000021, 0.2250000000000000333 ) ) ; +#73367 = SURFACE_STYLE_USAGE ( .BOTH. , #32556 ) ; +#73368 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#73369 = EDGE_CURVE ( 'NONE', #61919, #1345, #46789, .T. ) ; +#73370 = AXIS2_PLACEMENT_3D ( 'NONE', #9379, #57463, #32453 ) ; +#73371 = SURFACE_STYLE_USAGE ( .BOTH. , #34078 ) ; +#73372 = FILL_AREA_STYLE_COLOUR ( '', #3023 ) ; +#73373 = LINE ( 'NONE', #17703, #5296 ) ; +#73374 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56917 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16923, #48624, #2650 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73375 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73376 = FILL_AREA_STYLE_COLOUR ( '', #95617 ) ; +#73378 = EDGE_CURVE ( 'NONE', #59324, #84321, #95180, .T. ) ; +#73377 = PLANE ( 'NONE', #17732 ) ; +#73379 = FACE_OUTER_BOUND ( 'NONE', #74169, .T. ) ; +#73380 = ORIENTED_EDGE ( 'NONE', *, *, #55020, .T. ) ; +#73381 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73383 = LINE ( 'NONE', #63725, #27513 ) ; +#73382 = SURFACE_STYLE_FILL_AREA ( #43222 ) ; +#73384 = ADVANCED_FACE ( 'NONE', ( #54496 ), #63669, .T. ) ; +#73385 = EDGE_CURVE ( 'NONE', #37634, #27932, #5700, .T. ) ; +#73386 = STYLED_ITEM ( 'NONE', ( #34147 ), #86039 ) ; +#73387 = VECTOR ( 'NONE', #95610, 1000.000000000000000 ) ; +#73388 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#73389 = ORIENTED_EDGE ( 'NONE', *, *, #44568, .T. ) ; +#73390 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73391 = PRESENTATION_STYLE_ASSIGNMENT (( #3451 ) ) ; +#73392 = VECTOR ( 'NONE', #22952, 1000.000000000000000 ) ; +#73393 = EDGE_CURVE ( 'NONE', #21754, #25848, #88146, .T. ) ; +#73394 = FILL_AREA_STYLE ('',( #39324 ) ) ; +#73395 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57087 ) ) ; +#73396 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#73397 = AXIS2_PLACEMENT_3D ( 'NONE', #43534, #5696, #74702 ) ; +#73398 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76647 ) ) ; +#73399 = PLANE ( 'NONE', #22525 ) ; +#73400 = ORIENTED_EDGE ( 'NONE', *, *, #32828, .F. ) ; +#73401 = ORIENTED_EDGE ( 'NONE', *, *, #9378, .T. ) ; +#73402 = EDGE_CURVE ( 'NONE', #80708, #2215, #90509, .T. ) ; +#73403 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#73404 = STYLED_ITEM ( 'NONE', ( #64304 ), #80751 ) ; +#73405 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73406 = ORIENTED_EDGE ( 'NONE', *, *, #4827, .F. ) ; +#73407 = CARTESIAN_POINT ( 'NONE', ( 1.724073170230389973, -1.220939016933670018, 0.8299999999999999600 ) ) ; +#73408 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88274 ), #84814 ) ; +#73409 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73410 = SURFACE_STYLE_USAGE ( .BOTH. , #26948 ) ; +#73411 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73412 = ADVANCED_FACE ( 'NONE', ( #43537 ), #8922, .T. ) ; +#73413 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73414 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8099999999999502043 ) ) ; +#73415 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12969 ), #55497 ) ; +#73417 = EDGE_LOOP ( 'NONE', ( #98299, #73329, #70465, #96424 ) ) ; +#73416 = ORIENTED_EDGE ( 'NONE', *, *, #84541, .F. ) ; +#73418 = AXIS2_PLACEMENT_3D ( 'NONE', #17063, #95153, #15531 ) ; +#73419 = EDGE_LOOP ( 'NONE', ( #62159, #70597, #2184 ) ) ; +#73420 = VERTEX_POINT ( 'NONE', #98578 ) ; +#73421 = SURFACE_STYLE_FILL_AREA ( #10012 ) ; +#73422 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80045, 'distance_accuracy_value', 'NONE'); +#73423 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73424 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#73425 = ORIENTED_EDGE ( 'NONE', *, *, #77049, .F. ) ; +#73426 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73427 = VERTEX_POINT ( 'NONE', #75691 ) ; +#73428 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73429 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73430 = ORIENTED_EDGE ( 'NONE', *, *, #30941, .T. ) ; +#73432 = FILL_AREA_STYLE ('',( #18765 ) ) ; +#73431 = PLANE ( 'NONE', #73169 ) ; +#73433 = ORIENTED_EDGE ( 'NONE', *, *, #52356, .T. ) ; +#73434 = EDGE_LOOP ( 'NONE', ( #63760, #14458, #1546, #40140 ) ) ; +#73435 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29463 ), #8245 ) ; +#73436 = PRESENTATION_STYLE_ASSIGNMENT (( #1973 ) ) ; +#73438 = FACE_OUTER_BOUND ( 'NONE', #41984, .T. ) ; +#73437 = PRESENTATION_STYLE_ASSIGNMENT (( #10521 ) ) ; +#73439 = EDGE_CURVE ( 'NONE', #11287, #96833, #60415, .T. ) ; +#73442 = ORIENTED_EDGE ( 'NONE', *, *, #45184, .F. ) ; +#73441 = VECTOR ( 'NONE', #100003, 1000.000000000000000 ) ; +#73440 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73443 = ORIENTED_EDGE ( 'NONE', *, *, #99093, .F. ) ; +#73444 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#73445 = ORIENTED_EDGE ( 'NONE', *, *, #51733, .T. ) ; +#73447 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#73446 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#73448 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#73449 = ORIENTED_EDGE ( 'NONE', *, *, #55634, .T. ) ; +#73450 = EDGE_CURVE ( 'NONE', #64829, #35238, #4245, .T. ) ; +#73451 = ORIENTED_EDGE ( 'NONE', *, *, #26028, .F. ) ; +#73453 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#73452 = FACE_OUTER_BOUND ( 'NONE', #36877, .T. ) ; +#73454 = LINE ( 'NONE', #3509, #48172 ) ; +#73455 = SURFACE_STYLE_FILL_AREA ( #57659 ) ; +#73456 = VECTOR ( 'NONE', #58099, 1000.000000000000000 ) ; +#73457 = SURFACE_STYLE_FILL_AREA ( #58660 ) ; +#73458 = CARTESIAN_POINT ( 'NONE', ( -1.235803762811620077, -1.129864225586414639, 0.8099999999998921396 ) ) ; +#73459 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 5.551115123125790098E-17 ) ) ; +#73460 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #49833, #67124 ), + ( #80979, #81491 ), + ( #35522, #58015 ), + ( #42168, #59531 ), + ( #90625, #12928 ), + ( #75306, #66624 ), + ( #51834, #82967 ), + ( #3352, #19146 ), + ( #5304, #36519 ), + ( #73307, #65622 ), + ( #3840, #35020 ), + ( #27342, #68620 ), + ( #6760, #7766 ), + ( #62008, #38007 ), + ( #67606, #52338 ), + ( #61003, #30307 ), + ( #92106, #98690 ), + ( #100166, #38505 ), + ( #22171, #23192 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06270017598358139377, 0.1256167466604179994, 0.1889113015218140124, 0.2532600040886919812, 0.3171200007542330224, 0.3795159633805629817, 0.4405409028601919852, 0.5009929936201289458, 0.5609495532032120479, 0.6202221492738739794, 0.6797704147043319711, 0.7398130537205920287, 0.8009914761313710052, 0.8641828753275350161, 0.9298363305113630517, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#73461 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62016 ) ) ; +#73462 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73463 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87170, 'distance_accuracy_value', 'NONE'); +#73464 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43449 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12218, #61306, #85746 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73465 = VERTEX_POINT ( 'NONE', #58914 ) ; +#73466 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#73467 = EDGE_LOOP ( 'NONE', ( #28105, #50948, #82074, #32763 ) ) ; +#73468 = SURFACE_SIDE_STYLE ('',( #48981 ) ) ; +#73469 = AXIS2_PLACEMENT_3D ( 'NONE', #75428, #6900, #99331 ) ; +#73470 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.449999999999999956, -13.35000000000000142 ) ) ; +#73471 = AXIS2_PLACEMENT_3D ( 'NONE', #4683, #81338, #3688 ) ; +#73472 = LINE ( 'NONE', #81137, #69197 ) ; +#73473 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73474 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.900000000000000577, 0.000000000000000000 ) ) ; +#73475 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73476 = VERTEX_POINT ( 'NONE', #90005 ) ; +#73477 = EDGE_CURVE ( 'NONE', #7082, #2685, #2376, .T. ) ; +#73478 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42497 ) ) ; +#73479 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.723820061220085131, 0.000000000000000000 ) ) ; +#73480 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73481 = LINE ( 'NONE', #26015, #72174 ) ; +#73482 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73483 = LINE ( 'NONE', #66313, #64714 ) ; +#73484 = SURFACE_STYLE_USAGE ( .BOTH. , #4020 ) ; +#73485 = AXIS2_PLACEMENT_3D ( 'NONE', #46171, #31395, #76854 ) ; +#73486 = SURFACE_SIDE_STYLE ('',( #43323 ) ) ; +#73487 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73488 = VECTOR ( 'NONE', #49867, 1000.000000000000000 ) ; +#73489 = FILL_AREA_STYLE_COLOUR ( '', #86011 ) ; +#73490 = LINE ( 'NONE', #65821, #76657 ) ; +#73491 = LINE ( 'NONE', #57181, #20969 ) ; +#73492 = VECTOR ( 'NONE', #11220, 1000.000000000000114 ) ; +#73493 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73494 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 3.435721000000000025, 0.8991599999999999593 ) ) ; +#73495 = ORIENTED_EDGE ( 'NONE', *, *, #80978, .T. ) ; +#73496 = FILL_AREA_STYLE_COLOUR ( '', #3037 ) ; +#73497 = EDGE_LOOP ( 'NONE', ( #51268, #56820, #9309, #100560 ) ) ; +#73498 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#73499 = PRESENTATION_STYLE_ASSIGNMENT (( #57191 ) ) ; +#73500 = CARTESIAN_POINT ( 'NONE', ( 1.856855962848350083, -0.9758031678253591412, 0.8299999999999999600 ) ) ; +#73501 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65438 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45677, #76346, #13492 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73502 = CARTESIAN_POINT ( 'NONE', ( 1.799895807589950048, -1.058723197808659977, 0.8100000000000006084 ) ) ; +#73503 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73504 = LINE ( 'NONE', #25045, #28731 ) ; +#73505 = ORIENTED_EDGE ( 'NONE', *, *, #15913, .T. ) ; +#73506 = VERTEX_POINT ( 'NONE', #82368 ) ; +#73507 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73508 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64601, 'distance_accuracy_value', 'NONE'); +#73509 = VECTOR ( 'NONE', #3925, 1000.000000000000000 ) ; +#73510 = LINE ( 'NONE', #80175, #4246 ) ; +#73511 = SURFACE_SIDE_STYLE ('',( #57205 ) ) ; +#73512 = EDGE_CURVE ( 'NONE', #57360, #1743, #100553, .T. ) ; +#73513 = FACE_OUTER_BOUND ( 'NONE', #61710, .T. ) ; +#73514 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#73515 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73516 = ORIENTED_EDGE ( 'NONE', *, *, #53297, .T. ) ; +#73517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93152 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45089, #58984, #43114 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73518 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73519 = VERTEX_POINT ( 'NONE', #15387 ) ; +#73520 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73521 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73522 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#73523 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73524 = PLANE ( 'NONE', #72491 ) ; +#73525 = EDGE_CURVE ( 'NONE', #93963, #14378, #80584, .T. ) ; +#73526 = CIRCLE ( 'NONE', #97872, 0.3000000000000000444 ) ; +#73527 = CARTESIAN_POINT ( 'NONE', ( -1.056478722217069954, -0.9834456900322131601, 0.8100000000000000533 ) ) ; +#73528 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9803 ) ) ; +#73529 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#73530 = SURFACE_STYLE_FILL_AREA ( #64855 ) ; +#73531 = SURFACE_SIDE_STYLE ('',( #9636 ) ) ; +#73533 = ORIENTED_EDGE ( 'NONE', *, *, #63371, .T. ) ; +#73532 = ORIENTED_EDGE ( 'NONE', *, *, #43769, .F. ) ; +#73535 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#73534 = VECTOR ( 'NONE', #26360, 1000.000000000000000 ) ; +#73536 = STYLED_ITEM ( 'NONE', ( #99360 ), #85816 ) ; +#73537 = ORIENTED_EDGE ( 'NONE', *, *, #33977, .T. ) ; +#73538 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999830802, 0.01000000000000000021, 0.6914213562373291433 ) ) ; +#73539 = VECTOR ( 'NONE', #78573, 1000.000000000000114 ) ; +#73540 = LINE ( 'NONE', #90860, #30984 ) ; +#73541 = ORIENTED_EDGE ( 'NONE', *, *, #90173, .T. ) ; +#73542 = ORIENTED_EDGE ( 'NONE', *, *, #77424, .F. ) ; +#73543 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73544 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73545 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73546 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33950 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1787, #26281, #88545 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73547 = ORIENTED_EDGE ( 'NONE', *, *, #20932, .F. ) ; +#73548 = ORIENTED_EDGE ( 'NONE', *, *, #84305, .F. ) ; +#73549 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.500000000000000222, -0.02000000000002793293 ) ) ; +#73550 = ORIENTED_EDGE ( 'NONE', *, *, #4096, .F. ) ; +#73551 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73552 = EDGE_CURVE ( 'NONE', #63310, #48171, #86526, .T. ) ; +#73553 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68553 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11827, #28738, #35444 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73554 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73556 = VERTEX_POINT ( 'NONE', #587 ) ; +#73555 = PRESENTATION_STYLE_ASSIGNMENT (( #5564 ) ) ; +#73557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73558 = ORIENTED_EDGE ( 'NONE', *, *, #18330, .T. ) ; +#73559 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#73560 = SURFACE_STYLE_FILL_AREA ( #96500 ) ; +#73561 = ORIENTED_EDGE ( 'NONE', *, *, #13709, .T. ) ; +#73562 = EDGE_CURVE ( 'NONE', #21501, #5714, #23589, .T. ) ; +#73563 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#73564 = PLANE ( 'NONE', #2892 ) ; +#73565 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73566 = CARTESIAN_POINT ( 'NONE', ( -0.9897739841320261078, -1.331314275383060020, 0.8300000000000000711 ) ) ; +#73567 = AXIS2_PLACEMENT_3D ( 'NONE', #62243, #93319, #9015 ) ; +#73568 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#73569 = CARTESIAN_POINT ( 'NONE', ( -2.366666666666666696, 3.500000000000000000, 0.000000000000000000 ) ) ; +#73571 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#73570 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73572 = CARTESIAN_POINT ( 'NONE', ( 1.512782233897560058, -1.071137013546419992, 0.8299999999999997380 ) ) ; +#73573 = VERTEX_POINT ( 'NONE', #92008 ) ; +#73574 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73575 = CARTESIAN_POINT ( 'NONE', ( -0.9449124846862100302, -1.010972591757870021, 0.8300000000000000711 ) ) ; +#73576 = EDGE_LOOP ( 'NONE', ( #36872, #86031, #10631, #34841 ) ) ; +#73577 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24560 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42632, #4321, #19121 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73578 = SURFACE_SIDE_STYLE ('',( #11188 ) ) ; +#73579 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.6999999999999990674, 0.000000000000000000 ) ) ; +#73580 = CARTESIAN_POINT ( 'NONE', ( -0.3839949111172690221, -1.170868642971409912, 0.8300000000000000711 ) ) ; +#73581 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.7099999999999999645, -0.9464466094067264246 ) ) ; +#73582 = DIRECTION ( 'NONE', ( -0.6668863736986311297, 0.7451594222547881508, 0.000000000000000000 ) ) ; +#73583 = CARTESIAN_POINT ( 'NONE', ( 1.794978790831629922, -1.096743473147149928, 0.8100000000000000533 ) ) ; +#73584 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#73585 = EDGE_CURVE ( 'NONE', #72808, #38761, #99583, .T. ) ; +#73586 = PRESENTATION_STYLE_ASSIGNMENT (( #28620 ) ) ; +#73587 = VECTOR ( 'NONE', #1758, 1000.000000000000000 ) ; +#73588 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#73589 = SURFACE_SIDE_STYLE ('',( #18945 ) ) ; +#73590 = ADVANCED_FACE ( 'NONE', ( #15895 ), #85867, .T. ) ; +#73591 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#73592 = AXIS2_PLACEMENT_3D ( 'NONE', #98836, #20820, #13585 ) ; +#73593 = ORIENTED_EDGE ( 'NONE', *, *, #72210, .F. ) ; +#73594 = SURFACE_STYLE_USAGE ( .BOTH. , #42463 ) ; +#73595 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73596 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6669 ) ) ; +#73597 = LINE ( 'NONE', #81781, #1237 ) ; +#73598 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24541 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99219, #52367, #68643 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73599 = VECTOR ( 'NONE', #68013, 1000.000000000000000 ) ; +#73600 = ORIENTED_EDGE ( 'NONE', *, *, #63996, .F. ) ; +#73601 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73602 = EDGE_CURVE ( 'NONE', #85180, #10916, #13847, .T. ) ; +#73603 = STYLED_ITEM ( 'NONE', ( #70121 ), #7477 ) ; +#73604 = FACE_OUTER_BOUND ( 'NONE', #7131, .T. ) ; +#73605 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73606 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73607 = FACE_OUTER_BOUND ( 'NONE', #78905, .T. ) ; +#73608 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#73609 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73610 = SURFACE_STYLE_FILL_AREA ( #35838 ) ; +#73611 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#73612 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86348, 'distance_accuracy_value', 'NONE'); +#73613 = LINE ( 'NONE', #19486, #82813 ) ; +#73614 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47284 ), #3285 ) ; +#73615 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28563 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29436, #59628, #66716 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73616 = ORIENTED_EDGE ( 'NONE', *, *, #6157, .T. ) ; +#73617 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73618 = VERTEX_POINT ( 'NONE', #93979 ) ; +#73619 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#73620 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1791, 'distance_accuracy_value', 'NONE'); +#73621 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44997, 'distance_accuracy_value', 'NONE'); +#73622 = SURFACE_STYLE_USAGE ( .BOTH. , #64953 ) ; +#73623 = FACE_OUTER_BOUND ( 'NONE', #35041, .T. ) ; +#73624 = CARTESIAN_POINT ( 'NONE', ( -0.1525548447364439841, -1.164073081312986924, 0.8100000000000002753 ) ) ; +#73625 = ADVANCED_FACE ( 'NONE', ( #38409 ), #30213, .T. ) ; +#73626 = FILL_AREA_STYLE_COLOUR ( '', #89635 ) ; +#73627 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73628 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#73629 = FACE_OUTER_BOUND ( 'NONE', #60405, .T. ) ; +#73630 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#73631 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999920064, 1.899999999999980149, -0.02000000000000839995 ) ) ; +#73632 = ORIENTED_EDGE ( 'NONE', *, *, #39300, .T. ) ; +#73633 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.950000000000000178, 0.000000000000000000 ) ) ; +#73634 = FACE_OUTER_BOUND ( 'NONE', #53187, .T. ) ; +#73635 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#73636 = ORIENTED_EDGE ( 'NONE', *, *, #40116, .T. ) ; +#73637 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58336 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10336, #41599, #3289 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73638 = FACE_OUTER_BOUND ( 'NONE', #64213, .T. ) ; +#73639 = ORIENTED_EDGE ( 'NONE', *, *, #91489, .F. ) ; +#73640 = STYLED_ITEM ( 'NONE', ( #43257 ), #46374 ) ; +#73641 = SURFACE_STYLE_FILL_AREA ( #58357 ) ; +#73642 = FACE_OUTER_BOUND ( 'NONE', #48840, .T. ) ; +#73643 = PRESENTATION_STYLE_ASSIGNMENT (( #58358 ) ) ; +#73644 = LINE ( 'NONE', #65464, #47998 ) ; +#73645 = VERTEX_POINT ( 'NONE', #72075 ) ; +#73646 = FILL_AREA_STYLE ('',( #57868 ) ) ; +#73647 = EDGE_LOOP ( 'NONE', ( #50707, #31827, #98721, #13288 ) ) ; +#73648 = ORIENTED_EDGE ( 'NONE', *, *, #80765, .F. ) ; +#73649 = ORIENTED_EDGE ( 'NONE', *, *, #43398, .T. ) ; +#73650 = SURFACE_SIDE_STYLE ('',( #50210 ) ) ; +#73651 = FILL_AREA_STYLE_COLOUR ( '', #48993 ) ; +#73652 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73653 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73654 = CARTESIAN_POINT ( 'NONE', ( -0.4682333997055400099, -1.153630909546540018, 0.8299999999999999600 ) ) ; +#73655 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#73656 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73658 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73657 = CARTESIAN_POINT ( 'NONE', ( 0.2454021686453040363, -1.061343041336519910, 0.8299999999999999600 ) ) ; +#73659 = EDGE_LOOP ( 'NONE', ( #22382, #41494, #80476, #22805 ) ) ; +#73661 = VERTEX_POINT ( 'NONE', #10171 ) ; +#73660 = ORIENTED_EDGE ( 'NONE', *, *, #13633, .F. ) ; +#73662 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100965 ) ; +#73663 = ORIENTED_EDGE ( 'NONE', *, *, #90215, .F. ) ; +#73664 = AXIS2_PLACEMENT_3D ( 'NONE', #27369, #27889, #19696 ) ; +#73665 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#73666 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73667 = EDGE_CURVE ( 'NONE', #22432, #70688, #97250, .T. ) ; +#73668 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#73669 = VECTOR ( 'NONE', #99656, 1000.000000000000000 ) ; +#73670 = ORIENTED_EDGE ( 'NONE', *, *, #84937, .T. ) ; +#73672 = ORIENTED_EDGE ( 'NONE', *, *, #96763, .T. ) ; +#73671 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73673 = PLANE ( 'NONE', #15446 ) ; +#73674 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73675 = ORIENTED_EDGE ( 'NONE', *, *, #23461, .F. ) ; +#73676 = VERTEX_POINT ( 'NONE', #95512 ) ; +#73677 = ADVANCED_FACE ( 'NONE', ( #25617 ), #8669, .F. ) ; +#73678 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46297 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66505, #28219, #90488 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73679 = CARTESIAN_POINT ( 'NONE', ( 0.3121999599827350313, -1.334043206419958105, 0.8100000000000000533 ) ) ; +#73680 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#73681 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73682 = STYLED_ITEM ( 'NONE', ( #64822 ), #66259 ) ; +#73683 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#73684 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#73685 = CARTESIAN_POINT ( 'NONE', ( 1.765390738874589971, -1.428263396816370046, 0.8299999999999999600 ) ) ; +#73686 = VECTOR ( 'NONE', #64084, 1000.000000000000000 ) ; +#73687 = PRESENTATION_STYLE_ASSIGNMENT (( #36398 ) ) ; +#73688 = LINE ( 'NONE', #21952, #84206 ) ; +#73689 = SURFACE_STYLE_USAGE ( .BOTH. , #42553 ) ; +#73690 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 4.008477000000000068, 0.8991599999999999593 ) ) ; +#73691 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85779 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86435, #23148, #47116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73692 = LINE ( 'NONE', #3743, #93410 ) ; +#73693 = FILL_AREA_STYLE ('',( #70665 ) ) ; +#73694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73695 = VECTOR ( 'NONE', #86925, 1000.000000000000000 ) ; +#73696 = PRESENTATION_STYLE_ASSIGNMENT (( #4741 ) ) ; +#73697 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#73698 = ORIENTED_EDGE ( 'NONE', *, *, #51558, .F. ) ; +#73699 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73700 = AXIS2_PLACEMENT_3D ( 'NONE', #11658, #88868, #88362 ) ; +#73701 = EDGE_CURVE ( 'NONE', #72535, #46370, #15689, .T. ) ; +#73702 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.5000000000000000000, -13.15000000000000036 ) ) ; +#73703 = FILL_AREA_STYLE_COLOUR ( '', #62568 ) ; +#73704 = CARTESIAN_POINT ( 'NONE', ( 4.415099200572560001, 1.447728043919934038, -11.91363784554959970 ) ) ; +#73705 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#73706 = ORIENTED_EDGE ( 'NONE', *, *, #80245, .F. ) ; +#73707 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.600000000000000089, -13.40000000000000036 ) ) ; +#73709 = FILL_AREA_STYLE ('',( #35445 ) ) ; +#73708 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73710 = CARTESIAN_POINT ( 'NONE', ( 1.592056040834880060, -1.030915998478540097, 0.8100000000000000533 ) ) ; +#73711 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94167 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8123, #26078, #95467 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73712 = CARTESIAN_POINT ( 'NONE', ( -0.2325713810860060016, -1.366783821657739928, 0.8299999999999999600 ) ) ; +#73713 = SURFACE_STYLE_FILL_AREA ( #65054 ) ; +#73714 = LINE ( 'NONE', #65534, #27475 ) ; +#73715 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#73716 = FILL_AREA_STYLE ('',( #7064 ) ) ; +#73717 = EDGE_LOOP ( 'NONE', ( #74785, #67127, #39509, #68980 ) ) ; +#73718 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.216666666666666785, 0.000000000000000000 ) ) ; +#73719 = ADVANCED_FACE ( 'NONE', ( #65394 ), #97868, .F. ) ; +#73720 = CARTESIAN_POINT ( 'NONE', ( 6.106202999999999825, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#73721 = SURFACE_STYLE_FILL_AREA ( #19590 ) ; +#73722 = ADVANCED_FACE ( 'NONE', ( #82254 ), #75100, .T. ) ; +#73723 = CARTESIAN_POINT ( 'NONE', ( 1.063743438223609949, -0.9165513359838141083, 0.8299999999999994049 ) ) ; +#73724 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.099999999999960121, 0.000000000000000000 ) ) ; +#73725 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73726 = AXIS2_PLACEMENT_3D ( 'NONE', #52808, #76266, #6268 ) ; +#73727 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73728 = FILL_AREA_STYLE_COLOUR ( '', #13152 ) ; +#73729 = EDGE_CURVE ( 'NONE', #65336, #25544, #59806, .T. ) ; +#73730 = LINE ( 'NONE', #3783, #72961 ) ; +#73732 = SURFACE_STYLE_USAGE ( .BOTH. , #1789 ) ; +#73731 = VECTOR ( 'NONE', #10288, 1000.000000000000000 ) ; +#73733 = PRESENTATION_STYLE_ASSIGNMENT (( #57429 ) ) ; +#73734 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47639 ), #12571 ) ; +#73735 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100122, 'distance_accuracy_value', 'NONE'); +#73736 = FILL_AREA_STYLE_COLOUR ( '', #100593 ) ; +#73737 = FILL_AREA_STYLE ('',( #80918 ) ) ; +#73738 = VERTEX_POINT ( 'NONE', #65924 ) ; +#73740 = VERTEX_POINT ( 'NONE', #97020 ) ; +#73739 = AXIS2_PLACEMENT_3D ( 'NONE', #83456, #98677, #74792 ) ; +#73741 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56750, 'distance_accuracy_value', 'NONE'); +#73742 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25549, 'distance_accuracy_value', 'NONE'); +#73743 = FILL_AREA_STYLE ('',( #20099 ) ) ; +#73744 = CARTESIAN_POINT ( 'NONE', ( -1.386875452357819061, -1.365159793661682608, 0.8099999999997192779 ) ) ; +#73745 = EDGE_CURVE ( 'NONE', #78817, #19298, #27132, .T. ) ; +#73746 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#73747 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41116 ), #78605 ) ; +#73748 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73749 = LINE ( 'NONE', #4299, #40272 ) ; +#73750 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73751 = ORIENTED_EDGE ( 'NONE', *, *, #100717, .T. ) ; +#73752 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28069 ), #80323 ) ; +#73753 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#73754 = EDGE_CURVE ( 'NONE', #96910, #24186, #42927, .T. ) ; +#73755 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79486, 'distance_accuracy_value', 'NONE'); +#73756 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73757 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83896 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46839, #64704, #97319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73758 = ORIENTED_EDGE ( 'NONE', *, *, #85040, .T. ) ; +#73759 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73760 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.000000000000000000 ) ) ; +#73761 = ADVANCED_FACE ( 'NONE', ( #85737 ), #91890, .T. ) ; +#73762 = STYLED_ITEM ( 'NONE', ( #31281 ), #25471 ) ; +#73763 = LINE ( 'NONE', #36476, #84773 ) ; +#73765 = EDGE_CURVE ( 'NONE', #88953, #38419, #21948, .T. ) ; +#73764 = FILL_AREA_STYLE ('',( #95192 ) ) ; +#73766 = SURFACE_STYLE_USAGE ( .BOTH. , #42625 ) ; +#73767 = ORIENTED_EDGE ( 'NONE', *, *, #24478, .F. ) ; +#73768 = SURFACE_STYLE_FILL_AREA ( #42627 ) ; +#73769 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#73770 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27263, 'distance_accuracy_value', 'NONE'); +#73771 = EDGE_CURVE ( 'NONE', #55979, #54719, #91400, .T. ) ; +#73772 = LINE ( 'NONE', #27835, #41016 ) ; +#73773 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33023 ), #2059 ) ; +#73774 = CARTESIAN_POINT ( 'NONE', ( 1.644292209069110111, -0.9726617844338858454, 0.8099999999999994982 ) ) ; +#73775 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #42479 ) ) ; +#73776 = ORIENTED_EDGE ( 'NONE', *, *, #17620, .T. ) ; +#73777 = CARTESIAN_POINT ( 'NONE', ( 5.802146500499951287, 2.544766500499948680, 0.8991599999999999593 ) ) ; +#73778 = LINE ( 'NONE', #97703, #58703 ) ; +#73779 = VECTOR ( 'NONE', #22725, 1000.000000000000000 ) ; +#73780 = FACE_OUTER_BOUND ( 'NONE', #18503, .T. ) ; +#73782 = PRESENTATION_STYLE_ASSIGNMENT (( #42638 ) ) ; +#73781 = AXIS2_PLACEMENT_3D ( 'NONE', #62957, #15426, #14399 ) ; +#73783 = CARTESIAN_POINT ( 'NONE', ( -1.082141282666305493, -1.242263041859239747, 0.8099999999998097611 ) ) ; +#73784 = ORIENTED_EDGE ( 'NONE', *, *, #84874, .T. ) ; +#73785 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#73786 = STYLED_ITEM ( 'NONE', ( #100405 ), #46958 ) ; +#73787 = ADVANCED_FACE ( 'NONE', ( #45898 ), #61790, .T. ) ; +#73788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45963 ) ) ; +#73789 = ORIENTED_EDGE ( 'NONE', *, *, #9224, .F. ) ; +#73790 = ORIENTED_EDGE ( 'NONE', *, *, #99876, .T. ) ; +#73791 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#73792 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26507 ) ) ; +#73793 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#73794 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73795 = PRESENTATION_STYLE_ASSIGNMENT (( #42655 ) ) ; +#73796 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73797 = ORIENTED_EDGE ( 'NONE', *, *, #70404, .F. ) ; +#73798 = ADVANCED_FACE ( 'NONE', ( #46413 ), #53113, .T. ) ; +#73799 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, 0.2349999999999999867 ) ) ; +#73800 = CIRCLE ( 'NONE', #29747, 0.009999999999999998473 ) ; +#73801 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#73802 = STYLED_ITEM ( 'NONE', ( #34429 ), #34813 ) ; +#73803 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73804 = ORIENTED_EDGE ( 'NONE', *, *, #83429, .T. ) ; +#73805 = EDGE_CURVE ( 'NONE', #78778, #37298, #40819, .T. ) ; +#73806 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#73807 = ORIENTED_EDGE ( 'NONE', *, *, #34113, .T. ) ; +#73808 = VECTOR ( 'NONE', #61403, 1000.000000000000000 ) ; +#73809 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16686 ) ) ; +#73810 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29765 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51161, #88434, #65443 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73812 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.650000000000000355, 0.000000000000000000 ) ) ; +#73811 = CARTESIAN_POINT ( 'NONE', ( 0.1818071625306326711, -1.375720599612540784, 0.8100000000000001643 ) ) ; +#73813 = PRESENTATION_STYLE_ASSIGNMENT (( #42181 ) ) ; +#73814 = AXIS2_PLACEMENT_3D ( 'NONE', #11779, #28216, #35405 ) ; +#73815 = EDGE_LOOP ( 'NONE', ( #92578, #64874, #69364, #98182, #18272, #33937 ) ) ; +#73816 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#73817 = FILL_AREA_STYLE ('',( #18137 ) ) ; +#73818 = ORIENTED_EDGE ( 'NONE', *, *, #21246, .T. ) ; +#73819 = ORIENTED_EDGE ( 'NONE', *, *, #45897, .T. ) ; +#73820 = PRESENTATION_STYLE_ASSIGNMENT (( #80480 ) ) ; +#73822 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#73821 = LINE ( 'NONE', #12952, #21656 ) ; +#73823 = CARTESIAN_POINT ( 'NONE', ( -1.324712406799700037, -1.164020980542209927, 0.8299999999999999600 ) ) ; +#73824 = VECTOR ( 'NONE', #20309, 1000.000000000000000 ) ; +#73825 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.4245906043549200204, 0.000000000000000000 ) ) ; +#73826 = VECTOR ( 'NONE', #2933, 1000.000000000000000 ) ; +#73827 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#73828 = PRESENTATION_STYLE_ASSIGNMENT (( #43168 ) ) ; +#73830 = EDGE_CURVE ( 'NONE', #55576, #4472, #33145, .T. ) ; +#73829 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 7.282382000000000133, 0.8648700000000000276 ) ) ; +#73831 = FACE_OUTER_BOUND ( 'NONE', #89726, .T. ) ; +#73832 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73833 = ORIENTED_EDGE ( 'NONE', *, *, #4702, .T. ) ; +#73834 = CARTESIAN_POINT ( 'NONE', ( 1.360598746852770047, -1.365766081162230083, 0.8299999999999994049 ) ) ; +#73835 = VECTOR ( 'NONE', #51488, 1000.000000000000000 ) ; +#73838 = PRESENTATION_STYLE_ASSIGNMENT (( #81535 ) ) ; +#73837 = FACE_OUTER_BOUND ( 'NONE', #87316, .T. ) ; +#73836 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73839 = SURFACE_STYLE_FILL_AREA ( #50393 ) ; +#73840 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73841 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73842 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96896, 'distance_accuracy_value', 'NONE'); +#73843 = AXIS2_PLACEMENT_3D ( 'NONE', #35237, #65856, #5522 ) ; +#73844 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#73845 = EDGE_LOOP ( 'NONE', ( #38113, #56819, #84117, #3698 ) ) ; +#73846 = PRESENTATION_STYLE_ASSIGNMENT (( #65676 ) ) ; +#73847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73848 = FACE_OUTER_BOUND ( 'NONE', #82329, .T. ) ; +#73849 = EDGE_CURVE ( 'NONE', #27941, #99428, #48486, .T. ) ; +#73850 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#73851 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11793 ), #83622 ) ; +#73852 = PLANE ( 'NONE', #64863 ) ; +#73853 = FILL_AREA_STYLE_COLOUR ( '', #36640 ) ; +#73854 = ADVANCED_FACE ( 'NONE', ( #39271 ), #1505, .T. ) ; +#73855 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#73856 = SURFACE_STYLE_USAGE ( .BOTH. , #25406 ) ; +#73857 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37990 ) ) ; +#73858 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73859 = SURFACE_STYLE_USAGE ( .BOTH. , #36071 ) ; +#73860 = SURFACE_STYLE_USAGE ( .BOTH. , #18699 ) ; +#73861 = FILL_AREA_STYLE ('',( #66196 ) ) ; +#73862 = PLANE ( 'NONE', #48509 ) ; +#73863 = FACE_OUTER_BOUND ( 'NONE', #33251, .T. ) ; +#73864 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96638 ) ) ; +#73865 = PRESENTATION_STYLE_ASSIGNMENT (( #51897 ) ) ; +#73866 = CARTESIAN_POINT ( 'NONE', ( 1.797929489527180014, -1.085974092738730024, 0.8299999999999997380 ) ) ; +#73867 = VECTOR ( 'NONE', #89918, 1000.000000000000000 ) ; +#73868 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73869 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #97758, 'design' ) ; +#73870 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266014999999999890, 0.8991599999999999593 ) ) ; +#73871 = AXIS2_PLACEMENT_3D ( 'NONE', #74767, #90070, #76249 ) ; +#73872 = ORIENTED_EDGE ( 'NONE', *, *, #61948, .F. ) ; +#73873 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#73874 = FACE_OUTER_BOUND ( 'NONE', #62028, .T. ) ; +#73875 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76829, 'distance_accuracy_value', 'NONE'); +#73877 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33055 ) ) ; +#73876 = FILL_AREA_STYLE ('',( #50916 ) ) ; +#73878 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57577 ) ) ; +#73879 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11162, 'distance_accuracy_value', 'NONE'); +#73880 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68563 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20843, #13099, #5473 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73881 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#73882 = SURFACE_STYLE_USAGE ( .BOTH. , #55189 ) ; +#73883 = AXIS2_PLACEMENT_3D ( 'NONE', #80623, #88765, #87757 ) ; +#73884 = SURFACE_SIDE_STYLE ('',( #80551 ) ) ; +#73885 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#73886 = EDGE_LOOP ( 'NONE', ( #85401, #83380, #84193, #77683 ) ) ; +#73887 = FILL_AREA_STYLE_COLOUR ( '', #83127 ) ; +#73889 = ADVANCED_FACE ( 'NONE', ( #25504 ), #87767, .F. ) ; +#73888 = FACE_OUTER_BOUND ( 'NONE', #34265, .T. ) ; +#73890 = VECTOR ( 'NONE', #97501, 1000.000000000000000 ) ; +#73891 = SURFACE_SIDE_STYLE ('',( #11504 ) ) ; +#73892 = STYLED_ITEM ( 'NONE', ( #49243 ), #9467 ) ; +#73893 = LINE ( 'NONE', #11507, #79808 ) ; +#73894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19748, 'distance_accuracy_value', 'NONE'); +#73895 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#73896 = AXIS2_PLACEMENT_3D ( 'NONE', #91862, #60751, #90874 ) ; +#73897 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78469, 'distance_accuracy_value', 'NONE'); +#73898 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73899 = PRESENTATION_STYLE_ASSIGNMENT (( #80065 ) ) ; +#73900 = EDGE_LOOP ( 'NONE', ( #57333, #97483, #6144, #46383, #57832, #31202 ) ) ; +#73901 = EDGE_LOOP ( 'NONE', ( #74717, #81889, #7733, #8878 ) ) ; +#73902 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#73903 = DIRECTION ( 'NONE', ( 0.7071067811865435759, -0.7071067811865514585, 0.000000000000000000 ) ) ; +#73904 = ORIENTED_EDGE ( 'NONE', *, *, #84392, .T. ) ; +#73905 = CARTESIAN_POINT ( 'NONE', ( 1.809085324296979991, -1.273483528256009967, 0.8299999999999999600 ) ) ; +#73906 = CARTESIAN_POINT ( 'NONE', ( -0.7996232790101961418, 0.5990488921811000234, 0.8299999999999999600 ) ) ; +#73907 = SURFACE_STYLE_FILL_AREA ( #11526 ) ; +#73908 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#73910 = VERTEX_POINT ( 'NONE', #73470 ) ; +#73909 = EDGE_LOOP ( 'NONE', ( #13039, #60293, #41490, #24440 ) ) ; +#73911 = STYLED_ITEM ( 'NONE', ( #18658 ), #71015 ) ; +#73912 = ORIENTED_EDGE ( 'NONE', *, *, #45120, .F. ) ; +#73913 = ORIENTED_EDGE ( 'NONE', *, *, #35720, .F. ) ; +#73914 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73915 = LINE ( 'NONE', #3956, #50876 ) ; +#73916 = EDGE_LOOP ( 'NONE', ( #62058, #99627, #8231, #68977 ) ) ; +#73917 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73918 = EDGE_CURVE ( 'NONE', #44461, #57759, #59686, .T. ) ; +#73919 = AXIS2_PLACEMENT_3D ( 'NONE', #23226, #1767, #94646 ) ; +#73920 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73921 = ORIENTED_EDGE ( 'NONE', *, *, #71799, .F. ) ; +#73922 = ADVANCED_FACE ( 'NONE', ( #43808 ), #79950, .F. ) ; +#73924 = PRESENTATION_STYLE_ASSIGNMENT (( #28464 ) ) ; +#73923 = PLANE ( 'NONE', #91080 ) ; +#73925 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64573 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69282, #62209, #30001 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73926 = VERTEX_POINT ( 'NONE', #83128 ) ; +#73927 = ORIENTED_EDGE ( 'NONE', *, *, #8885, .T. ) ; +#73928 = PLANE ( 'NONE', #65610 ) ; +#73929 = SURFACE_STYLE_FILL_AREA ( #34643 ) ; +#73930 = CARTESIAN_POINT ( 'NONE', ( 1.830402071067120051, -1.199770973383029959, 0.8300000000000004041 ) ) ; +#73931 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#73933 = ADVANCED_FACE ( 'NONE', ( #100811 ), #37672, .T. ) ; +#73932 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#73935 = ORIENTED_EDGE ( 'NONE', *, *, #41567, .T. ) ; +#73934 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73936 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73937 = ORIENTED_EDGE ( 'NONE', *, *, #91776, .F. ) ; +#73938 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#73939 = AXIS2_PLACEMENT_3D ( 'NONE', #60553, #90143, #66665 ) ; +#73940 = VECTOR ( 'NONE', #44207, 1000.000000000000000 ) ; +#73941 = VERTEX_POINT ( 'NONE', #53493 ) ; +#73943 = SURFACE_STYLE_USAGE ( .BOTH. , #4474 ) ; +#73942 = LINE ( 'NONE', #1983, #33546 ) ; +#73944 = ORIENTED_EDGE ( 'NONE', *, *, #10547, .F. ) ; +#73945 = EDGE_CURVE ( 'NONE', #5281, #55713, #61670, .T. ) ; +#73946 = ORIENTED_EDGE ( 'NONE', *, *, #84525, .F. ) ; +#73947 = VECTOR ( 'NONE', #67180, 1000.000000000000000 ) ; +#73949 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#73948 = SURFACE_STYLE_USAGE ( .BOTH. , #13074 ) ; +#73950 = AXIS2_PLACEMENT_3D ( 'NONE', #11895, #97704, #88098 ) ; +#73951 = AXIS2_PLACEMENT_3D ( 'NONE', #20962, #53122, #12727 ) ; +#73952 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#73953 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73954 = EDGE_CURVE ( 'NONE', #75075, #23904, #29973, .T. ) ; +#73955 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44094 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14168, #60222, #36219 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73956 = EDGE_CURVE ( 'NONE', #32262, #28814, #83633, .T. ) ; +#73957 = AXIS2_PLACEMENT_3D ( 'NONE', #94445, #3059, #95444 ) ; +#73958 = ORIENTED_EDGE ( 'NONE', *, *, #69316, .F. ) ; +#73959 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#73960 = EDGE_LOOP ( 'NONE', ( #79444, #6024, #91554 ) ) ; +#73961 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#73962 = ADVANCED_FACE ( 'NONE', ( #61169 ), #30998, .T. ) ; +#73963 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17321 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78728, #23120, #32786 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73964 = EDGE_CURVE ( 'NONE', #34472, #2708, #44784, .T. ) ; +#73965 = CARTESIAN_POINT ( 'NONE', ( 1.438017692675660042, -1.296821915455180108, 0.8299999999999999600 ) ) ; +#73966 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73967 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 0.1000000000000000056, -11.41999999999999993 ) ) ; +#73968 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#73969 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#73970 = ORIENTED_EDGE ( 'NONE', *, *, #11344, .F. ) ; +#73971 = EDGE_CURVE ( 'NONE', #36642, #83944, #47835, .T. ) ; +#73972 = CARTESIAN_POINT ( 'NONE', ( 0.1802163075021840088, -1.026304639009830044, 0.8299999999999999600 ) ) ; +#73973 = DIRECTION ( 'NONE', ( 0.7071064476869688420, -0.7071071146859688739, 0.000000000000000000 ) ) ; +#73974 = VECTOR ( 'NONE', #12892, 1000.000000000000000 ) ; +#73975 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73976 = DIRECTION ( 'NONE', ( -0.7071090539100457484, -0.7071045084557444627, 0.000000000000000000 ) ) ; +#73977 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#73978 = EDGE_CURVE ( 'NONE', #53924, #12661, #48378, .T. ) ; +#73979 = SURFACE_STYLE_FILL_AREA ( #90288 ) ; +#73980 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8465 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87125, #57019, #78953 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#73981 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#73982 = SURFACE_STYLE_USAGE ( .BOTH. , #50530 ) ; +#73983 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#73984 = AXIS2_PLACEMENT_3D ( 'NONE', #17980, #41506, #81339 ) ; +#73985 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36853, 'distance_accuracy_value', 'NONE'); +#73986 = VERTEX_POINT ( 'NONE', #55528 ) ; +#73987 = CARTESIAN_POINT ( 'NONE', ( 1.512782233897560058, -1.071137013546419992, 0.8100000000000000533 ) ) ; +#73988 = SURFACE_STYLE_FILL_AREA ( #50030 ) ; +#73989 = ORIENTED_EDGE ( 'NONE', *, *, #32251, .T. ) ; +#73990 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#73991 = PRESENTATION_STYLE_ASSIGNMENT (( #96939 ) ) ; +#73992 = SURFACE_STYLE_USAGE ( .BOTH. , #72989 ) ; +#73993 = CIRCLE ( 'NONE', #5499, 0.009999999999999998473 ) ; +#73994 = SURFACE_STYLE_USAGE ( .BOTH. , #88810 ) ; +#73995 = CARTESIAN_POINT ( 'NONE', ( 1.792693045999540047, -1.018845982455530041, 0.8100000000000006084 ) ) ; +#73996 = VECTOR ( 'NONE', #28676, 1000.000000000000000 ) ; +#73997 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8648700000000000276 ) ) ; +#73998 = ORIENTED_EDGE ( 'NONE', *, *, #15929, .F. ) ; +#73999 = VECTOR ( 'NONE', #16386, 1000.000000000000114 ) ; +#74000 = VERTEX_POINT ( 'NONE', #15648 ) ; +#74001 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#74002 = EDGE_CURVE ( 'NONE', #54937, #81292, #22340, .T. ) ; +#74003 = LINE ( 'NONE', #71234, #1107 ) ; +#74004 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#74005 = SURFACE_SIDE_STYLE ('',( #26052 ) ) ; +#74006 = LINE ( 'NONE', #87815, #11336 ) ; +#74007 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90425, 'distance_accuracy_value', 'NONE'); +#74008 = VECTOR ( 'NONE', #71976, 1000.000000000000114 ) ; +#74009 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#74010 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7087, 'distance_accuracy_value', 'NONE'); +#74011 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74012 = ADVANCED_FACE ( 'NONE', ( #39158 ), #8429, .F. ) ; +#74013 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30850 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37073, #99720, #30360 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74014 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#74015 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#74016 = ORIENTED_EDGE ( 'NONE', *, *, #63216, .T. ) ; +#74018 = VECTOR ( 'NONE', #12976, 1000.000000000000000 ) ; +#74017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10280 ), #7004 ) ; +#74019 = SURFACE_STYLE_FILL_AREA ( #97465 ) ; +#74020 = EDGE_LOOP ( 'NONE', ( #38599, #51186, #17997, #38829 ) ) ; +#74021 = SURFACE_SIDE_STYLE ('',( #75515 ) ) ; +#74022 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#74023 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3897 ) ) ; +#74024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57736 ), #60983 ) ; +#74025 = PLANE ( 'NONE', #74068 ) ; +#74026 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74027 = CARTESIAN_POINT ( 'NONE', ( -0.7486876120449308392, 1.376287671486961850, 0.8100000000000000533 ) ) ; +#74030 = ORIENTED_EDGE ( 'NONE', *, *, #84979, .F. ) ; +#74029 = VERTEX_POINT ( 'NONE', #9456 ) ; +#74028 = EDGE_CURVE ( 'NONE', #67465, #24285, #24891, .T. ) ; +#74031 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74032 = VERTEX_POINT ( 'NONE', #71831 ) ; +#74033 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88675 ), #29975 ) ; +#74034 = PRESENTATION_STYLE_ASSIGNMENT (( #44361 ) ) ; +#74035 = ORIENTED_EDGE ( 'NONE', *, *, #5880, .F. ) ; +#74037 = EDGE_CURVE ( 'NONE', #56911, #63825, #85622, .T. ) ; +#74036 = EDGE_LOOP ( 'NONE', ( #63891, #3029, #56238, #32428 ) ) ; +#74038 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74039 = FACE_OUTER_BOUND ( 'NONE', #95115, .T. ) ; +#74040 = FILL_AREA_STYLE ('',( #95477 ) ) ; +#74041 = FILL_AREA_STYLE ('',( #64868 ) ) ; +#74042 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16935 ) ) ; +#74044 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74043 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74045 = ORIENTED_EDGE ( 'NONE', *, *, #89023, .F. ) ; +#74046 = ORIENTED_EDGE ( 'NONE', *, *, #34311, .T. ) ; +#74047 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87181 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78430, #75065, #69744 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74048 = ORIENTED_EDGE ( 'NONE', *, *, #38667, .T. ) ; +#74049 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#74050 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#74051 = AXIS2_PLACEMENT_3D ( 'NONE', #53607, #92378, #8040 ) ; +#74052 = VERTEX_POINT ( 'NONE', #95772 ) ; +#74053 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8648700000000000276 ) ) ; +#74054 = VECTOR ( 'NONE', #78703, 1000.000000000000000 ) ; +#74055 = ORIENTED_EDGE ( 'NONE', *, *, #32163, .T. ) ; +#74056 = CARTESIAN_POINT ( 'NONE', ( -0.09657079632682520620, -1.219829592979950084, 0.8299999999999999600 ) ) ; +#74057 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74058 = VERTEX_POINT ( 'NONE', #77970 ) ; +#74059 = EDGE_LOOP ( 'NONE', ( #33703, #15735, #11111, #46586 ) ) ; +#74060 = SURFACE_SIDE_STYLE ('',( #97512 ) ) ; +#74061 = ORIENTED_EDGE ( 'NONE', *, *, #35720, .T. ) ; +#74062 = LINE ( 'NONE', #66400, #77440 ) ; +#74063 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#74064 = AXIS2_PLACEMENT_3D ( 'NONE', #96535, #95524, #12605 ) ; +#74065 = SURFACE_STYLE_FILL_AREA ( #92248 ) ; +#74066 = CARTESIAN_POINT ( 'NONE', ( -1.180619344033760010, -1.219266740403220028, 0.8300000000000000711 ) ) ; +#74067 = STYLED_ITEM ( 'NONE', ( #85782 ), #48092 ) ; +#74068 = AXIS2_PLACEMENT_3D ( 'NONE', #66851, #45342, #13150 ) ; +#74069 = PRESENTATION_STYLE_ASSIGNMENT (( #50611 ) ) ; +#74070 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74071 = LINE ( 'NONE', #4121, #79195 ) ; +#74072 = CARTESIAN_POINT ( 'NONE', ( 1.688788655318780085, -0.9001377335631759458, 0.8299999999999997380 ) ) ; +#74073 = ORIENTED_EDGE ( 'NONE', *, *, #21326, .T. ) ; +#74074 = SURFACE_STYLE_USAGE ( .BOTH. , #4607 ) ; +#74075 = AXIS2_PLACEMENT_3D ( 'NONE', #98726, #43670, #64289 ) ; +#74076 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74077 = EDGE_LOOP ( 'NONE', ( #83502, #86104, #37901, #75064 ) ) ; +#74078 = STYLED_ITEM ( 'NONE', ( #61716 ), #25910 ) ; +#74079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74080 = EDGE_CURVE ( 'NONE', #73172, #82566, #33019, .T. ) ; +#74081 = CARTESIAN_POINT ( 'NONE', ( -0.1759195832032370010, -1.500900992704750081, 0.8100000000000000533 ) ) ; +#74082 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#74083 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5514 ), #84064 ) ; +#74084 = AXIS2_PLACEMENT_3D ( 'NONE', #91297, #61195, #67307 ) ; +#74085 = SURFACE_STYLE_USAGE ( .BOTH. , #42930 ) ; +#74086 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74087 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8648700000000000276 ) ) ; +#74088 = SURFACE_STYLE_FILL_AREA ( #60791 ) ; +#74090 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57804 ) ) ; +#74089 = VECTOR ( 'NONE', #18889, 1000.000000000000000 ) ; +#74091 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74092 = EDGE_CURVE ( 'NONE', #33578, #21416, #95265, .T. ) ; +#74093 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74094 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#74095 = CIRCLE ( 'NONE', #10417, 0.1099999999999998479 ) ; +#74096 = LINE ( 'NONE', #2640, #67752 ) ; +#74097 = ADVANCED_FACE ( 'NONE', ( #860 ), #7929, .T. ) ; +#74098 = AXIS2_PLACEMENT_3D ( 'NONE', #79805, #97090, #9758 ) ; +#74099 = VERTEX_POINT ( 'NONE', #57541 ) ; +#74100 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31664 ) ) ; +#74102 = PLANE ( 'NONE', #35547 ) ; +#74101 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74103 = LINE ( 'NONE', #73094, #84334 ) ; +#74104 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85238 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66255, #35639, #19266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74105 = VECTOR ( 'NONE', #57911, 1000.000000000000000 ) ; +#74106 = VECTOR ( 'NONE', #88352, 1000.000000000000000 ) ; +#74107 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31636, 'distance_accuracy_value', 'NONE'); +#74108 = ORIENTED_EDGE ( 'NONE', *, *, #97218, .T. ) ; +#74109 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74110 = FILL_AREA_STYLE ('',( #50645 ) ) ; +#74111 = FILL_AREA_STYLE ('',( #34823 ) ) ; +#74112 = LINE ( 'NONE', #58322, #97049 ) ; +#74113 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74114 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#74115 = CARTESIAN_POINT ( 'NONE', ( 0.7666666666666606123, 3.500000000000000000, 0.000000000000000000 ) ) ; +#74116 = AXIS2_PLACEMENT_3D ( 'NONE', #86826, #56208, #72020 ) ; +#74117 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#74118 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74119 = ORIENTED_EDGE ( 'NONE', *, *, #14293, .F. ) ; +#74120 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#74121 = ORIENTED_EDGE ( 'NONE', *, *, #80958, .F. ) ; +#74122 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74123 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39876, 'distance_accuracy_value', 'NONE'); +#74124 = FILL_AREA_STYLE_COLOUR ( '', #19485 ) ; +#74125 = CARTESIAN_POINT ( 'NONE', ( -2.966666666666666785, 3.500000000000000000, 0.000000000000000000 ) ) ; +#74126 = CARTESIAN_POINT ( 'NONE', ( -0.2258383435392919969, -1.079063990458370093, 0.8299999999999999600 ) ) ; +#74127 = SURFACE_SIDE_STYLE ('',( #27184 ) ) ; +#74128 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#74129 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666627084, -2.700000000000000178, 3.495651678169879387E-76 ) ) ; +#74130 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39867 ), #38265 ) ; +#74131 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#74132 = AXIS2_PLACEMENT_3D ( 'NONE', #94394, #9070, #31125 ) ; +#74133 = FACE_OUTER_BOUND ( 'NONE', #50803, .T. ) ; +#74134 = FILL_AREA_STYLE_COLOUR ( '', #52677 ) ; +#74135 = EDGE_CURVE ( 'NONE', #26462, #58927, #79299, .T. ) ; +#74136 = ORIENTED_EDGE ( 'NONE', *, *, #25557, .T. ) ; +#74137 = PRESENTATION_STYLE_ASSIGNMENT (( #35854 ) ) ; +#74138 = FILL_AREA_STYLE ('',( #96071 ) ) ; +#74139 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#74140 = ORIENTED_EDGE ( 'NONE', *, *, #36639, .F. ) ; +#74141 = FACE_OUTER_BOUND ( 'NONE', #68952, .T. ) ; +#74142 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74143 = ORIENTED_EDGE ( 'NONE', *, *, #40758, .F. ) ; +#74144 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92038 ) ) ; +#74145 = STYLED_ITEM ( 'NONE', ( #1200 ), #26649 ) ; +#74146 = SURFACE_STYLE_USAGE ( .BOTH. , #96583 ) ; +#74147 = PLANE ( 'NONE', #31613 ) ; +#74148 = PLANE ( 'NONE', #56079 ) ; +#74149 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96925 ), #59464 ) ; +#74150 = FACE_OUTER_BOUND ( 'NONE', #59770, .T. ) ; +#74151 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.000000000000000000, -12.24500000000000099 ) ) ; +#74152 = ORIENTED_EDGE ( 'NONE', *, *, #10581, .T. ) ; +#74153 = PRESENTATION_STYLE_ASSIGNMENT (( #88971 ) ) ; +#74154 = EDGE_LOOP ( 'NONE', ( #27742, #52337, #56868, #54165 ) ) ; +#74155 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, -3.099999999999980549, 0.000000000000000000 ) ) ; +#74156 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74157 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48063 ) ) ; +#74158 = CIRCLE ( 'NONE', #4105, 0.1999999999999996503 ) ; +#74159 = FILL_AREA_STYLE ('',( #43000 ) ) ; +#74160 = ORIENTED_EDGE ( 'NONE', *, *, #26981, .T. ) ; +#74161 = VERTEX_POINT ( 'NONE', #11955 ) ; +#74163 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74162 = VECTOR ( 'NONE', #91602, 1000.000000000000000 ) ; +#74164 = SURFACE_STYLE_FILL_AREA ( #4207 ) ; +#74165 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92067 ), #79046 ) ; +#74166 = CARTESIAN_POINT ( 'NONE', ( 2.973719499500051100, 5.373193499500048098, 0.8991599999999999593 ) ) ; +#74167 = CARTESIAN_POINT ( 'NONE', ( 0.2827097938661469745, -0.9901059572320288771, 0.8299999999999999600 ) ) ; +#74168 = VERTEX_POINT ( 'NONE', #41697 ) ; +#74170 = EDGE_LOOP ( 'NONE', ( #8913, #82121, #59239, #68502 ) ) ; +#74169 = EDGE_LOOP ( 'NONE', ( #100020, #56836, #41233, #55700 ) ) ; +#74171 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74172 = EDGE_CURVE ( 'NONE', #37734, #17391, #82510, .T. ) ; +#74173 = ORIENTED_EDGE ( 'NONE', *, *, #42914, .T. ) ; +#74174 = STYLED_ITEM ( 'NONE', ( #73022 ), #97666 ) ; +#74175 = ORIENTED_EDGE ( 'NONE', *, *, #83755, .T. ) ; +#74177 = ORIENTED_EDGE ( 'NONE', *, *, #38260, .F. ) ; +#74176 = LINE ( 'NONE', #21050, #96661 ) ; +#74178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80686 ) ) ; +#74179 = LINE ( 'NONE', #20531, #53111 ) ; +#74180 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.000000000000000000 ) ) ; +#74181 = ORIENTED_EDGE ( 'NONE', *, *, #42784, .T. ) ; +#74182 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#74183 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74184 = ORIENTED_EDGE ( 'NONE', *, *, #78848, .F. ) ; +#74185 = EDGE_CURVE ( 'NONE', #5416, #68985, #43178, .T. ) ; +#74186 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74187 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.5105124837953329830, -1.000000000000000000 ) ) ; +#74188 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74189 = AXIS2_PLACEMENT_3D ( 'NONE', #92371, #85213, #5572 ) ; +#74190 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#74191 = CARTESIAN_POINT ( 'NONE', ( 1.817674829793840319, -1.368793146596559929, 0.8100000000000000533 ) ) ; +#74192 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74193 = CARTESIAN_POINT ( 'NONE', ( -0.2142558627640144542, -1.025729774117964510, 0.8100000000002077760 ) ) ; +#74194 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57914 ), #88842 ) ; +#74195 = ORIENTED_EDGE ( 'NONE', *, *, #68725, .T. ) ; +#74196 = ADVANCED_FACE ( 'NONE', ( #50874 ), #4868, .T. ) ; +#74197 = SURFACE_STYLE_FILL_AREA ( #35915 ) ; +#74198 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19639 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79918, #85658, #9853 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74199 = SURFACE_STYLE_FILL_AREA ( #11809 ) ; +#74200 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 9.545123000000000246, 0.8648700000000000276 ) ) ; +#74201 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, 0.000000000000000000, 0.2999999999999999889 ) ) ; +#74202 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74203 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2494 ), #85635 ) ; +#74204 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.5000000000000000000, -0.02000000000001400310 ) ) ; +#74205 = CARTESIAN_POINT ( 'NONE', ( 1.033493568211090174, -0.9379159637996601351, 0.8299999999999999600 ) ) ; +#74206 = VECTOR ( 'NONE', #31337, 1000.000000000000000 ) ; +#74207 = ORIENTED_EDGE ( 'NONE', *, *, #97644, .T. ) ; +#74209 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74208 = FILL_AREA_STYLE ('',( #10309 ) ) ; +#74210 = STYLED_ITEM ( 'NONE', ( #9176 ), #26947 ) ; +#74211 = SURFACE_STYLE_FILL_AREA ( #20064 ) ; +#74212 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#74213 = EDGE_CURVE ( 'NONE', #53732, #36642, #20747, .T. ) ; +#74214 = SURFACE_SIDE_STYLE ('',( #73221 ) ) ; +#74215 = VERTEX_POINT ( 'NONE', #65670 ) ; +#74216 = FILL_AREA_STYLE ('',( #62299 ) ) ; +#74218 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, -3.099999999999960121, 0.000000000000000000 ) ) ; +#74217 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74219 = CARTESIAN_POINT ( 'NONE', ( 1.628132030843780553, -1.431361989143760116, 0.8099999999999976108 ) ) ; +#74220 = FACE_OUTER_BOUND ( 'NONE', #24376, .T. ) ; +#74221 = LINE ( 'NONE', #21098, #43107 ) ; +#74222 = VECTOR ( 'NONE', #37460, 1000.000000000000000 ) ; +#74223 = FILL_AREA_STYLE_COLOUR ( '', #32351 ) ; +#74224 = STYLED_ITEM ( 'NONE', ( #99859 ), #22406 ) ; +#74225 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74226 = ORIENTED_EDGE ( 'NONE', *, *, #4625, .F. ) ; +#74227 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#74228 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74229 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#74230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57943 ), #38304 ) ; +#74231 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17134 ) ) ; +#74232 = CARTESIAN_POINT ( 'NONE', ( 1.206696428571430113, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#74233 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74234 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#74235 = FILL_AREA_STYLE_COLOUR ( '', #67021 ) ; +#74236 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8199999999999999512 ) ) ; +#74237 = SURFACE_SIDE_STYLE ('',( #81910 ) ) ; +#74238 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90556 ), #64475 ) ; +#74239 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#74240 = SURFACE_STYLE_USAGE ( .BOTH. , #41600 ) ; +#74241 = ADVANCED_FACE ( 'NONE', ( #57044 ), #80502, .T. ) ; +#74242 = SURFACE_STYLE_USAGE ( .BOTH. , #27800 ) ; +#74243 = VERTEX_POINT ( 'NONE', #91159 ) ; +#74244 = EDGE_LOOP ( 'NONE', ( #9019, #78395, #76414, #89883 ) ) ; +#74245 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 3.393295000000000172, 0.8991599999999999593 ) ) ; +#74246 = FACE_OUTER_BOUND ( 'NONE', #53475, .T. ) ; +#74247 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74248 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74249 = FILL_AREA_STYLE ('',( #27292 ) ) ; +#74250 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48851, #57028, #96269 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74251 = SURFACE_STYLE_USAGE ( .BOTH. , #51780 ) ; +#74252 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74253 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#74254 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#74255 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74256 = EDGE_CURVE ( 'NONE', #73120, #60973, #52869, .T. ) ; +#74257 = ORIENTED_EDGE ( 'NONE', *, *, #64917, .T. ) ; +#74258 = SURFACE_STYLE_USAGE ( .BOTH. , #81937 ) ; +#74259 = SURFACE_STYLE_FILL_AREA ( #51288 ) ; +#74260 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8100000000000000533 ) ) ; +#74261 = AXIS2_PLACEMENT_3D ( 'NONE', #31702, #30178, #8131 ) ; +#74262 = VERTEX_POINT ( 'NONE', #6324 ) ; +#74263 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74264 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74265 = PRESENTATION_STYLE_ASSIGNMENT (( #18084 ) ) ; +#74266 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#74267 = CARTESIAN_POINT ( 'NONE', ( -1.309030937367239966, -1.351519064127929992, 0.8299999999999999600 ) ) ; +#74268 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74269 = ORIENTED_EDGE ( 'NONE', *, *, #80120, .F. ) ; +#74270 = FILL_AREA_STYLE_COLOUR ( '', #27778 ) ; +#74271 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74272 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#74273 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85693 ) ) ; +#74274 = VECTOR ( 'NONE', #73785, 1000.000000000000000 ) ; +#74276 = EDGE_CURVE ( 'NONE', #3831, #45393, #61551, .T. ) ; +#74275 = ORIENTED_EDGE ( 'NONE', *, *, #59479, .F. ) ; +#74277 = VECTOR ( 'NONE', #38935, 1000.000000000000000 ) ; +#74278 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8648700000000000276 ) ) ; +#74279 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#74280 = PRESENTATION_STYLE_ASSIGNMENT (( #42639 ) ) ; +#74281 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#74282 = VECTOR ( 'NONE', #85804, 1000.000000000000000 ) ; +#74283 = ORIENTED_EDGE ( 'NONE', *, *, #35939, .T. ) ; +#74284 = STYLED_ITEM ( 'NONE', ( #54679 ), #25754 ) ; +#74285 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74286 = EDGE_CURVE ( 'NONE', #14953, #1339, #7309, .T. ) ; +#74287 = EDGE_CURVE ( 'NONE', #75028, #32231, #21207, .T. ) ; +#74288 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #67513 ) ; +#74289 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4166 ) ) ; +#74290 = ORIENTED_EDGE ( 'NONE', *, *, #94083, .T. ) ; +#74292 = EDGE_LOOP ( 'NONE', ( #71696, #3922, #34860, #85814 ) ) ; +#74291 = PRESENTATION_STYLE_ASSIGNMENT (( #59999 ) ) ; +#74294 = AXIS2_PLACEMENT_3D ( 'NONE', #74120, #12244, #91438 ) ; +#74293 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41791, 'distance_accuracy_value', 'NONE'); +#74296 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.2000000000000000111, -12.44500000000000028 ) ) ; +#74295 = SURFACE_SIDE_STYLE ('',( #34512 ) ) ; +#74297 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#74298 = AXIS2_PLACEMENT_3D ( 'NONE', #37357, #7096, #60349 ) ; +#74299 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74300 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74301 = ORIENTED_EDGE ( 'NONE', *, *, #30278, .F. ) ; +#74302 = EDGE_CURVE ( 'NONE', #75920, #80616, #76836, .T. ) ; +#74303 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#74304 = EDGE_CURVE ( 'NONE', #29318, #51680, #36555, .T. ) ; +#74305 = AXIS2_PLACEMENT_3D ( 'NONE', #16413, #86407, #24661 ) ; +#74306 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#74307 = ORIENTED_EDGE ( 'NONE', *, *, #47675, .T. ) ; +#74308 = DIRECTION ( 'NONE', ( 0.7071067811865446862, 0.000000000000000000, 0.7071067811865503483 ) ) ; +#74309 = EDGE_LOOP ( 'NONE', ( #44616, #23146, #88606, #61079 ) ) ; +#74310 = VECTOR ( 'NONE', #89881, 1000.000000000000000 ) ; +#74311 = STYLED_ITEM ( 'NONE', ( #28210 ), #13320 ) ; +#74312 = CARTESIAN_POINT ( 'NONE', ( 0.1648571099708991683, -1.412818103019282567, 0.8100000000000002753 ) ) ; +#74313 = FACE_OUTER_BOUND ( 'NONE', #58978, .T. ) ; +#74314 = ORIENTED_EDGE ( 'NONE', *, *, #100087, .T. ) ; +#74315 = SURFACE_STYLE_USAGE ( .BOTH. , #11931 ) ; +#74316 = EDGE_CURVE ( 'NONE', #74391, #72651, #67645, .T. ) ; +#74317 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8991599999999999593 ) ) ; +#74318 = ORIENTED_EDGE ( 'NONE', *, *, #64172, .T. ) ; +#74320 = ORIENTED_EDGE ( 'NONE', *, *, #83188, .F. ) ; +#74319 = SHAPE_REPRESENTATION ( 'Imported', ( #82894 ), #28975 ) ; +#74321 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74323 = SURFACE_STYLE_FILL_AREA ( #43159 ) ; +#74322 = PRESENTATION_STYLE_ASSIGNMENT (( #51857 ) ) ; +#74324 = CARTESIAN_POINT ( 'NONE', ( -1.362892881570719972, -1.113830263093820161, 0.8299999999999999600 ) ) ; +#74326 = EDGE_CURVE ( 'NONE', #97466, #16858, #12505, .T. ) ; +#74325 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#74327 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74328 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#74329 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20522 ), #14063 ) ; +#74330 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#74331 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.123820061220055511, 0.000000000000000000 ) ) ; +#74332 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74333 = ADVANCED_FACE ( 'NONE', ( #46158 ), #100202, .F. ) ; +#74334 = ORIENTED_EDGE ( 'NONE', *, *, #54130, .F. ) ; +#74335 = FACE_OUTER_BOUND ( 'NONE', #84947, .T. ) ; +#74336 = FILL_AREA_STYLE_COLOUR ( '', #20315 ) ; +#74337 = EDGE_CURVE ( 'NONE', #30348, #90714, #14506, .T. ) ; +#74338 = LINE ( 'NONE', #4375, #57787 ) ; +#74339 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70228, 'distance_accuracy_value', 'NONE'); +#74340 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077919165, 0.6899999999999999467, 4.598363044682735356E-18 ) ) ; +#74341 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82069 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57018, #64645, #56520 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74342 = STYLED_ITEM ( 'NONE', ( #64165 ), #90418 ) ; +#74343 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48273 ) ) ; +#74344 = CARTESIAN_POINT ( 'NONE', ( -1.399999999999999467, 0.7099999999999999645, 0.9464466094067266466 ) ) ; +#74345 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74346 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#74347 = FACE_OUTER_BOUND ( 'NONE', #15935, .T. ) ; +#74348 = ORIENTED_EDGE ( 'NONE', *, *, #60652, .F. ) ; +#74349 = LINE ( 'NONE', #51383, #32538 ) ; +#74350 = AXIS2_PLACEMENT_3D ( 'NONE', #1637, #64919, #65401 ) ; +#74351 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74352 = SURFACE_STYLE_USAGE ( .BOTH. , #43187 ) ; +#74353 = VECTOR ( 'NONE', #59535, 1000.000000000000000 ) ; +#74355 = SURFACE_STYLE_FILL_AREA ( #58567 ) ; +#74354 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66183 ) ) ; +#74356 = PRESENTATION_STYLE_ASSIGNMENT (( #5357 ) ) ; +#74357 = PRESENTATION_STYLE_ASSIGNMENT (( #49889 ) ) ; +#74358 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.80755800000000022, 0.8648700000000000276 ) ) ; +#74359 = SURFACE_STYLE_FILL_AREA ( #74852 ) ; +#74360 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74361 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#74362 = FACE_OUTER_BOUND ( 'NONE', #84411, .T. ) ; +#74363 = EDGE_CURVE ( 'NONE', #61084, #18155, #30341, .T. ) ; +#74365 = PLANE ( 'NONE', #76168 ) ; +#74364 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70719 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65241, #88239, #80586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74366 = FILL_AREA_STYLE_COLOUR ( '', #40676 ) ; +#74367 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#74368 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74369 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54061 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45903, #7050, #77086 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74370 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74371 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#74372 = SURFACE_STYLE_USAGE ( .BOTH. , #43211 ) ; +#74373 = CARTESIAN_POINT ( 'NONE', ( -0.2950099738946450056, -1.071137013546419992, 0.8300000000000009592 ) ) ; +#74374 = SURFACE_SIDE_STYLE ('',( #37590 ) ) ; +#74375 = ADVANCED_FACE ( 'NONE', ( #94134 ), #23739, .T. ) ; +#74376 = ORIENTED_EDGE ( 'NONE', *, *, #89384, .F. ) ; +#74377 = AXIS2_PLACEMENT_3D ( 'NONE', #92829, #22951, #8522 ) ; +#74378 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74380 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#74379 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.499999999999960032, -0.02000000000000000042 ) ) ; +#74381 = EDGE_CURVE ( 'NONE', #62914, #9046, #48239, .T. ) ; +#74382 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13658 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87297, #34718, #96945 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74383 = AXIS2_PLACEMENT_3D ( 'NONE', #79073, #39236, #9026 ) ; +#74384 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#74385 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74386 = ORIENTED_EDGE ( 'NONE', *, *, #47040, .T. ) ; +#74387 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#74389 = EDGE_CURVE ( 'NONE', #5007, #78446, #30868, .T. ) ; +#74388 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74390 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74391 = VERTEX_POINT ( 'NONE', #87522 ) ; +#74392 = SURFACE_STYLE_USAGE ( .BOTH. , #43724 ) ; +#74393 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74394 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#74395 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74396 = LINE ( 'NONE', #36113, #11002 ) ; +#74397 = EDGE_LOOP ( 'NONE', ( #92935, #29228, #77246, #76701 ) ) ; +#74398 = VERTEX_POINT ( 'NONE', #79882 ) ; +#74399 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74400 = PRESENTATION_STYLE_ASSIGNMENT (( #4430 ) ) ; +#74401 = ORIENTED_EDGE ( 'NONE', *, *, #60822, .F. ) ; +#74402 = CARTESIAN_POINT ( 'NONE', ( 1.702517484154870031, -1.219598171061480052, 0.8100000000000000533 ) ) ; +#74403 = FILL_AREA_STYLE_COLOUR ( '', #59787 ) ; +#74404 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74405 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, 0.000000000000000000 ) ) ; +#74406 = EDGE_CURVE ( 'NONE', #210, #454, #55903, .T. ) ; +#74407 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000222, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#74408 = ADVANCED_FACE ( 'NONE', ( #16535 ), #10548, .F. ) ; +#74409 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74410 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74412 = ORIENTED_EDGE ( 'NONE', *, *, #30772, .F. ) ; +#74411 = ORIENTED_EDGE ( 'NONE', *, *, #75376, .T. ) ; +#74413 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #75506 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #93186 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#74414 = ORIENTED_EDGE ( 'NONE', *, *, #917, .T. ) ; +#74415 = VERTEX_POINT ( 'NONE', #41577 ) ; +#74416 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#74417 = CARTESIAN_POINT ( 'NONE', ( 0.1238200612200860418, 3.099999999999980105, 0.000000000000000000 ) ) ; +#74418 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89074 ) ) ; +#74419 = AXIS2_PLACEMENT_3D ( 'NONE', #40184, #78464, #55008 ) ; +#74420 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8684, 'distance_accuracy_value', 'NONE'); +#74421 = AXIS2_PLACEMENT_3D ( 'NONE', #47972, #79131, #54648 ) ; +#74422 = LINE ( 'NONE', #60135, #49065 ) ; +#74423 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74424 = VERTEX_POINT ( 'NONE', #97161 ) ; +#74425 = EDGE_CURVE ( 'NONE', #54713, #27603, #10837, .T. ) ; +#74426 = CIRCLE ( 'NONE', #59744, 1.383450513437169960 ) ; +#74427 = LINE ( 'NONE', #90735, #75951 ) ; +#74428 = CARTESIAN_POINT ( 'NONE', ( -0.1450079136436681071, -1.164927051866627927, 0.8100000000000000533 ) ) ; +#74429 = VECTOR ( 'NONE', #63531, 1000.000000000000114 ) ; +#74430 = EDGE_CURVE ( 'NONE', #41304, #24344, #43064, .T. ) ; +#74431 = CARTESIAN_POINT ( 'NONE', ( -1.196111491924880088, -0.8867570690059840555, 0.8299999999999999600 ) ) ; +#74432 = VERTEX_POINT ( 'NONE', #80387 ) ; +#74433 = VECTOR ( 'NONE', #69727, 1000.000000000000000 ) ; +#74435 = SURFACE_STYLE_USAGE ( .BOTH. , #51471 ) ; +#74434 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74436 = ORIENTED_EDGE ( 'NONE', *, *, #45688, .F. ) ; +#74437 = VERTEX_POINT ( 'NONE', #27271 ) ; +#74438 = CARTESIAN_POINT ( 'NONE', ( 0.9903538716760360572, -1.113830263093820161, 0.8100000000000000533 ) ) ; +#74440 = SURFACE_SIDE_STYLE ('',( #73929 ) ) ; +#74439 = PLANE ( 'NONE', #72276 ) ; +#74441 = CARTESIAN_POINT ( 'NONE', ( 1.880917842042550081, -1.247909878090150082, 0.8300000000000004041 ) ) ; +#74442 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63078 ) ) ; +#74443 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74445 = EDGE_LOOP ( 'NONE', ( #66931, #91096, #30529, #57472, #94111 ) ) ; +#74444 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8648700000000000276 ) ) ; +#74446 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#74447 = ORIENTED_EDGE ( 'NONE', *, *, #83068, .T. ) ; +#74448 = ADVANCED_FACE ( 'NONE', ( #74220 ), #33424, .T. ) ; +#74449 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74450 = ORIENTED_EDGE ( 'NONE', *, *, #80077, .F. ) ; +#74451 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#74452 = LINE ( 'NONE', #43785, #95006 ) ; +#74453 = EDGE_LOOP ( 'NONE', ( #6966, #13474, #27307, #95640 ) ) ; +#74454 = ORIENTED_EDGE ( 'NONE', *, *, #68926, .T. ) ; +#74456 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#74455 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74457 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#74458 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46649 ), #61417 ) ; +#74459 = EDGE_CURVE ( 'NONE', #73573, #87220, #71400, .T. ) ; +#74460 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74461 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#74462 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32108 ) ) ; +#74463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74465 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#74464 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51758, #82888, #44068, #8566 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#74466 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11004, 'distance_accuracy_value', 'NONE'); +#74467 = AXIS2_PLACEMENT_3D ( 'NONE', #93821, #15209, #77043 ) ; +#74468 = EDGE_CURVE ( 'NONE', #60233, #32857, #75711, .T. ) ; +#74469 = VERTEX_POINT ( 'NONE', #67050 ) ; +#74470 = ORIENTED_EDGE ( 'NONE', *, *, #86312, .T. ) ; +#74471 = EDGE_CURVE ( 'NONE', #16868, #81497, #60924, .T. ) ; +#74472 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#74473 = PRESENTATION_STYLE_ASSIGNMENT (( #81136 ) ) ; +#74474 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40480 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21652, #37498, #99176 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74475 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74476 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.449999999999999956, -11.32000000000000028 ) ) ; +#74477 = LINE ( 'NONE', #4495, #89514 ) ; +#74478 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#74479 = DIRECTION ( 'NONE', ( 0.7071045084557444627, -0.7071090539100457484, 0.000000000000000000 ) ) ; +#74480 = EDGE_LOOP ( 'NONE', ( #42306, #13688, #61978, #49013 ) ) ; +#74481 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#74482 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74483 = CARTESIAN_POINT ( 'NONE', ( 9.818513499500047814, 9.135001499500052802, 0.8991599999999999593 ) ) ; +#74484 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74485 = FILL_AREA_STYLE ('',( #66796 ) ) ; +#74486 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52512 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61218, #100367, #13650 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74487 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999960476, 3.500000000000000444, 0.000000000000000000 ) ) ; +#74488 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74489 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83014, 'distance_accuracy_value', 'NONE'); +#74490 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8648700000000000276 ) ) ; +#74491 = AXIS2_PLACEMENT_3D ( 'NONE', #29727, #99090, #60906 ) ; +#74492 = ADVANCED_FACE ( 'NONE', ( #13343 ), #12348, .T. ) ; +#74493 = PRESENTATION_STYLE_ASSIGNMENT (( #74987 ) ) ; +#74494 = FILL_AREA_STYLE ('',( #19341 ) ) ; +#74495 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6128, #23540, #54171, #24055 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#74496 = CARTESIAN_POINT ( 'NONE', ( 1.338207848547039891, -1.047446665233070062, 0.8299999999999995159 ) ) ; +#74497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40239 ) ) ; +#74498 = VERTEX_POINT ( 'NONE', #36429 ) ; +#74499 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74500 = CARTESIAN_POINT ( 'NONE', ( 1.525294525926170097, -1.013847726018640039, 0.8100000000000000533 ) ) ; +#74501 = ADVANCED_FACE ( 'NONE', ( #90536 ), #44062, .T. ) ; +#74502 = VERTEX_POINT ( 'NONE', #60871 ) ; +#74503 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -8.513155458356185007E-18, 0.3000000000000000444 ) ) ; +#74504 = VECTOR ( 'NONE', #20846, 1000.000000000000000 ) ; +#74505 = SURFACE_STYLE_USAGE ( .BOTH. , #5009 ) ; +#74507 = VECTOR ( 'NONE', #44272, 1000.000000000000000 ) ; +#74506 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74509 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.000000000000000000, 1.149999999999999911 ) ) ; +#74508 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60470 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82490, #36534, #43647 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74510 = EDGE_CURVE ( 'NONE', #35018, #21356, #85320, .T. ) ; +#74511 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#74512 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.6899999999999999467, 4.461702328476395893E-18 ) ) ; +#74513 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76005 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71896, #18742, #49934 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74514 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74515 = ORIENTED_EDGE ( 'NONE', *, *, #76261, .F. ) ; +#74516 = ORIENTED_EDGE ( 'NONE', *, *, #79035, .F. ) ; +#74517 = STYLED_ITEM ( 'NONE', ( #50399 ), #62228 ) ; +#74518 = SURFACE_SIDE_STYLE ('',( #52041 ) ) ; +#74519 = EDGE_CURVE ( 'NONE', #53732, #73059, #84330, .T. ) ; +#74520 = SURFACE_SIDE_STYLE ('',( #21372 ) ) ; +#74521 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74522 = STYLED_ITEM ( 'NONE', ( #42839 ), #40689 ) ; +#74523 = CARTESIAN_POINT ( 'NONE', ( -0.4444287376170629744, -1.091919226080539929, 0.8100000000000000533 ) ) ; +#74524 = STYLED_ITEM ( 'NONE', ( #19112 ), #16071 ) ; +#74525 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#74526 = DIRECTION ( 'NONE', ( -2.356961244533699997E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74527 = PRESENTATION_STYLE_ASSIGNMENT (( #20374 ) ) ; +#74528 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74530 = AXIS2_PLACEMENT_3D ( 'NONE', #52491, #59688, #4985 ) ; +#74529 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.01499999999999998383, 0.1400000000000000133 ) ) ; +#74531 = ORIENTED_EDGE ( 'NONE', *, *, #18197, .T. ) ; +#74532 = VECTOR ( 'NONE', #97678, 1000.000000000000000 ) ; +#74533 = FILL_AREA_STYLE ('',( #43365 ) ) ; +#74534 = VERTEX_POINT ( 'NONE', #93950 ) ; +#74535 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#74536 = VECTOR ( 'NONE', #59366, 1000.000000000000000 ) ; +#74537 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#74538 = EDGE_CURVE ( 'NONE', #31497, #39329, #15859, .T. ) ; +#74539 = EDGE_CURVE ( 'NONE', #47067, #58131, #74695, .T. ) ; +#74540 = FACE_OUTER_BOUND ( 'NONE', #67504, .T. ) ; +#74541 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11729 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85964, #24734, #64510 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74542 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74543 = SURFACE_STYLE_USAGE ( .BOTH. , #28079 ) ; +#74544 = CARTESIAN_POINT ( 'NONE', ( -1.167182179144840237, -0.9547617453595670378, 0.8100000000000000533 ) ) ; +#74545 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 1.399999999999999911, -11.36999999999999922 ) ) ; +#74547 = VERTEX_POINT ( 'NONE', #46506 ) ; +#74546 = ORIENTED_EDGE ( 'NONE', *, *, #34386, .F. ) ; +#74548 = ORIENTED_EDGE ( 'NONE', *, *, #93753, .F. ) ; +#74549 = AXIS2_PLACEMENT_3D ( 'NONE', #38379, #45474, #84327 ) ; +#74550 = CARTESIAN_POINT ( 'NONE', ( 1.674754468276729691, -0.9004049383407728424, 0.8099999999999981659 ) ) ; +#74552 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74551 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#74553 = ORIENTED_EDGE ( 'NONE', *, *, #66337, .T. ) ; +#74554 = EDGE_LOOP ( 'NONE', ( #69512, #53087, #95030, #61371 ) ) ; +#74555 = EDGE_CURVE ( 'NONE', #32963, #19759, #47028, .T. ) ; +#74556 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#74557 = DIRECTION ( 'NONE', ( -1.000000000000000000, -2.385832768178450048E-26, -3.399536532815460200E-14 ) ) ; +#74558 = ORIENTED_EDGE ( 'NONE', *, *, #29199, .F. ) ; +#74559 = ORIENTED_EDGE ( 'NONE', *, *, #55890, .F. ) ; +#74560 = EDGE_CURVE ( 'NONE', #56847, #49837, #90935, .T. ) ; +#74561 = VERTEX_POINT ( 'NONE', #61873 ) ; +#74562 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.6761799387799151129, -0.02000000000000000042 ) ) ; +#74563 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#74565 = ORIENTED_EDGE ( 'NONE', *, *, #3251, .T. ) ; +#74564 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74566 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4356 ), #76149 ) ; +#74567 = VECTOR ( 'NONE', #72849, 1000.000000000000000 ) ; +#74568 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#74569 = CARTESIAN_POINT ( 'NONE', ( 2.366666666666663144, 3.500000000000000000, 0.000000000000000000 ) ) ; +#74570 = VERTEX_POINT ( 'NONE', #93460 ) ; +#74571 = FILL_AREA_STYLE ('',( #75559 ) ) ; +#74572 = ORIENTED_EDGE ( 'NONE', *, *, #59502, .F. ) ; +#74573 = VERTEX_POINT ( 'NONE', #92946 ) ; +#74574 = PLANE ( 'NONE', #91032 ) ; +#74575 = STYLED_ITEM ( 'NONE', ( #63071 ), #55101 ) ; +#74576 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#74577 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74578 = STYLED_ITEM ( 'NONE', ( #586 ), #79170 ) ; +#74579 = CARTESIAN_POINT ( 'NONE', ( -0.9982971928311329401, -1.296162859166370307, 0.8300000000000000711 ) ) ; +#74580 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94660, #63058, #53867, #16537 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#74581 = PLANE ( 'NONE', #65101 ) ; +#74582 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25609 ) ) ; +#74583 = LINE ( 'NONE', #28603, #89910 ) ; +#74584 = EDGE_LOOP ( 'NONE', ( #7009, #28568, #11048, #29679 ) ) ; +#74585 = STYLED_ITEM ( 'NONE', ( #51651 ), #62496 ) ; +#74586 = CARTESIAN_POINT ( 'NONE', ( -0.9164863243573180274, -1.381526214478759895, 0.8299999999999999600 ) ) ; +#74587 = ORIENTED_EDGE ( 'NONE', *, *, #35139, .F. ) ; +#74588 = EDGE_CURVE ( 'NONE', #87602, #45477, #23562, .T. ) ; +#74589 = SURFACE_SIDE_STYLE ('',( #10685 ) ) ; +#74590 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74591 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74592 = CARTESIAN_POINT ( 'NONE', ( -0.3921422844660710227, -1.185705927526510051, 0.8300000000000000711 ) ) ; +#74593 = PRESENTATION_STYLE_ASSIGNMENT (( #43431 ) ) ; +#74594 = STYLED_ITEM ( 'NONE', ( #49535 ), #23205 ) ; +#74595 = ADVANCED_FACE ( 'NONE', ( #37386 ), #16355, .T. ) ; +#74597 = SURFACE_STYLE_FILL_AREA ( #4616 ) ; +#74596 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000020295, 0.1458578643762672711 ) ) ; +#74598 = CLOSED_SHELL ( 'NONE', ( #61746, #56855, #92710, #32408, #19554, #86039 ) ) ; +#74599 = PLANE ( 'NONE', #90685 ) ; +#74600 = SURFACE_STYLE_FILL_AREA ( #43436 ) ; +#74601 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12554 ) ) ; +#74602 = STYLED_ITEM ( 'NONE', ( #61836 ), #100425 ) ; +#74603 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74604 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.100000000000000089, 0.1829999999999830096 ) ) ; +#74605 = AXIS2_PLACEMENT_3D ( 'NONE', #11171, #35784, #88370 ) ; +#74606 = ORIENTED_EDGE ( 'NONE', *, *, #5786, .F. ) ; +#74607 = FILL_AREA_STYLE_COLOUR ( '', #12909 ) ; +#74608 = ADVANCED_FACE ( 'NONE', ( #14331 ), #47535, .T. ) ; +#74609 = DIRECTION ( 'NONE', ( 4.640777529015779698E-48, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74610 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#74611 = VECTOR ( 'NONE', #58698, 1000.000000000000000 ) ; +#74612 = ORIENTED_EDGE ( 'NONE', *, *, #89272, .T. ) ; +#74613 = PRESENTATION_STYLE_ASSIGNMENT (( #76103 ) ) ; +#74614 = ADVANCED_FACE ( 'NONE', ( #94481 ), #3094, .T. ) ; +#74615 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74616 = LINE ( 'NONE', #98010, #86911 ) ; +#74617 = PLANE ( 'NONE', #92580 ) ; +#74618 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74619 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.000000000000000000 ) ) ; +#74620 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74621 = LINE ( 'NONE', #51664, #739 ) ; +#74622 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74623 = AXIS2_PLACEMENT_3D ( 'NONE', #4986, #20836, #82631 ) ; +#74624 = VERTEX_POINT ( 'NONE', #26092 ) ; +#74625 = ORIENTED_EDGE ( 'NONE', *, *, #92619, .T. ) ; +#74626 = EDGE_CURVE ( 'NONE', #88940, #18757, #17386, .T. ) ; +#74627 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83652, 'distance_accuracy_value', 'NONE'); +#74628 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61969, 'distance_accuracy_value', 'NONE'); +#74629 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74630 = LINE ( 'NONE', #4172, #98461 ) ; +#74631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42052 ), #1214 ) ; +#74632 = AXIS2_PLACEMENT_3D ( 'NONE', #48249, #39560, #32914 ) ; +#74633 = LINE ( 'NONE', #35850, #27706 ) ; +#74634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74635 = PRESENTATION_STYLE_ASSIGNMENT (( #43474 ) ) ; +#74636 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74637 = CARTESIAN_POINT ( 'NONE', ( 8.093172500499999700, 4.142827499500000066, 0.8991599999999999593 ) ) ; +#74638 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74639 = EDGE_CURVE ( 'NONE', #68214, #57374, #64376, .T. ) ; +#74640 = VERTEX_POINT ( 'NONE', #57247 ) ; +#74642 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74641 = VECTOR ( 'NONE', #33440, 1000.000000000000000 ) ; +#74643 = FILL_AREA_STYLE_COLOUR ( '', #55339 ) ; +#74644 = ORIENTED_EDGE ( 'NONE', *, *, #7692, .F. ) ; +#74645 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99662, #23185, #6282, #68614 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#74646 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74647 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74648 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48569 ), #30568 ) ; +#74649 = ORIENTED_EDGE ( 'NONE', *, *, #56953, .T. ) ; +#74650 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74651 = EDGE_CURVE ( 'NONE', #63005, #57703, #48575, .T. ) ; +#74652 = EDGE_CURVE ( 'NONE', #20028, #28432, #56792, .T. ) ; +#74653 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87685 ), #84394 ) ; +#74654 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#74655 = FILL_AREA_STYLE ('',( #99526 ) ) ; +#74656 = SURFACE_STYLE_FILL_AREA ( #43490 ) ; +#74657 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22445 ) ) ; +#74658 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74659 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74660 = ORIENTED_EDGE ( 'NONE', *, *, #1064, .F. ) ; +#74662 = EDGE_CURVE ( 'NONE', #4549, #5540, #18390, .T. ) ; +#74661 = PRESENTATION_STYLE_ASSIGNMENT (( #73152 ) ) ; +#74663 = EDGE_CURVE ( 'NONE', #17149, #31741, #63883, .T. ) ; +#74665 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74664 = SURFACE_STYLE_USAGE ( .BOTH. , #83820 ) ; +#74666 = ORIENTED_EDGE ( 'NONE', *, *, #60486, .T. ) ; +#74667 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17547 ) ) ; +#74668 = CARTESIAN_POINT ( 'NONE', ( 0.1833333333333339865, -3.099999999999980549, 0.000000000000000000 ) ) ; +#74669 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74670 = CLOSED_SHELL ( 'NONE', ( #27537, #59716, #51786, #89516, #719, #779 ) ) ; +#74671 = EDGE_LOOP ( 'NONE', ( #33632, #44332, #47403, #1807 ) ) ; +#74672 = ORIENTED_EDGE ( 'NONE', *, *, #75010, .F. ) ; +#74673 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#74674 = AXIS2_PLACEMENT_3D ( 'NONE', #81194, #80688, #73514 ) ; +#74675 = PRESENTATION_STYLE_ASSIGNMENT (( #66490 ) ) ; +#74677 = EDGE_CURVE ( 'NONE', #60383, #45083, #49577, .T. ) ; +#74676 = CARTESIAN_POINT ( 'NONE', ( 1.705268638847220242, -0.9625006208768249749, 0.8300000000000004041 ) ) ; +#74678 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#74679 = ORIENTED_EDGE ( 'NONE', *, *, #89424, .F. ) ; +#74680 = VERTEX_POINT ( 'NONE', #79717 ) ; +#74681 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#74682 = ORIENTED_EDGE ( 'NONE', *, *, #11477, .T. ) ; +#74683 = ADVANCED_FACE ( 'NONE', ( #10655 ), #57763, .F. ) ; +#74684 = VERTEX_POINT ( 'NONE', #73549 ) ; +#74685 = CYLINDRICAL_SURFACE ( 'NONE', #57379, 0.01000000000000002623 ) ; +#74686 = FILL_AREA_STYLE_COLOUR ( '', #87276 ) ; +#74687 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74688 = SURFACE_STYLE_USAGE ( .BOTH. , #43517 ) ; +#74689 = ORIENTED_EDGE ( 'NONE', *, *, #91341, .F. ) ; +#74690 = PLANE ( 'NONE', #45539 ) ; +#74691 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.500000000000000444, 0.000000000000000000 ) ) ; +#74692 = ORIENTED_EDGE ( 'NONE', *, *, #66446, .T. ) ; +#74693 = SURFACE_SIDE_STYLE ('',( #3727 ) ) ; +#74694 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#74695 = CIRCLE ( 'NONE', #42044, 0.009999999999999998473 ) ; +#74696 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74697 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74698 = CARTESIAN_POINT ( 'NONE', ( 1.813028831487849990, -1.379727385542079965, 0.8299999999999999600 ) ) ; +#74699 = CYLINDRICAL_SURFACE ( 'NONE', #20430, 0.04999999999999991257 ) ; +#74700 = AXIS2_PLACEMENT_3D ( 'NONE', #41084, #1780, #10320 ) ; +#74701 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974019543, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#74702 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#74703 = ORIENTED_EDGE ( 'NONE', *, *, #63716, .T. ) ; +#74704 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74705 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4784314575050762075, -0.2458578643762690530 ) ) ; +#74706 = SURFACE_STYLE_USAGE ( .BOTH. , #66530 ) ; +#74707 = ADVANCED_FACE ( 'NONE', ( #59270 ), #13181, .F. ) ; +#74709 = PRESENTATION_STYLE_ASSIGNMENT (( #35918 ) ) ; +#74708 = CARTESIAN_POINT ( 'NONE', ( 0.3880979930239000231, -0.9663965808142249703, 0.8299999999999999600 ) ) ; +#74710 = SURFACE_SIDE_STYLE ('',( #43541 ) ) ; +#74711 = SURFACE_STYLE_USAGE ( .BOTH. , #82864 ) ; +#74712 = STYLED_ITEM ( 'NONE', ( #73991 ), #55371 ) ; +#74713 = PLANE ( 'NONE', #85766 ) ; +#74714 = SURFACE_STYLE_FILL_AREA ( #43544 ) ; +#74715 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71430 ) ) ; +#74716 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74717 = ORIENTED_EDGE ( 'NONE', *, *, #38178, .T. ) ; +#74718 = SURFACE_SIDE_STYLE ('',( #50263 ) ) ; +#74719 = ORIENTED_EDGE ( 'NONE', *, *, #32950, .T. ) ; +#74720 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74721 = CARTESIAN_POINT ( 'NONE', ( 1.644292209069110111, -0.9726617844338859564, 0.8299999999999999600 ) ) ; +#74722 = VECTOR ( 'NONE', #49995, 1000.000000000000000 ) ; +#74723 = LINE ( 'NONE', #14887, #91991 ) ; +#74724 = VECTOR ( 'NONE', #8984, 1000.000000000000000 ) ; +#74725 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74726 = CLOSED_SHELL ( 'NONE', ( #81648, #62816, #91002, #17216, #64615, #2819, #88527, #64817, #67457, #25778, #68619, #82175 ) ) ; +#74727 = VERTEX_POINT ( 'NONE', #19410 ) ; +#74728 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.593649167310369874, -11.41999999999999993 ) ) ; +#74729 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#74730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3546 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37352, #14793, #37834 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74731 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#74732 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74733 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363688888, -1.186323051948053209, 0.8099999999999676348 ) ) ; +#74734 = SURFACE_STYLE_FILL_AREA ( #83889 ) ; +#74735 = SURFACE_STYLE_FILL_AREA ( #44561 ) ; +#74736 = AXIS2_PLACEMENT_3D ( 'NONE', #99944, #69388, #77083 ) ; +#74737 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74738 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74739 = LINE ( 'NONE', #80402, #8746 ) ; +#74740 = SURFACE_SIDE_STYLE ('',( #50785 ) ) ; +#74741 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36676, 'distance_accuracy_value', 'NONE'); +#74742 = AXIS2_PLACEMENT_3D ( 'NONE', #84147, #14148, #31026 ) ; +#74743 = CARTESIAN_POINT ( 'NONE', ( -2.216666666666666785, 3.100000000000000533, 0.000000000000000000 ) ) ; +#74744 = STYLED_ITEM ( 'NONE', ( #95753 ), #50041 ) ; +#74745 = FILL_AREA_STYLE ('',( #97669 ) ) ; +#74746 = ORIENTED_EDGE ( 'NONE', *, *, #91205, .T. ) ; +#74747 = ORIENTED_EDGE ( 'NONE', *, *, #17797, .T. ) ; +#74748 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#74749 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93887, 'distance_accuracy_value', 'NONE'); +#74750 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80178, 'distance_accuracy_value', 'NONE'); +#74751 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74752 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74753 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74754 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8099999999998432898 ) ) ; +#74755 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.4600000000000000200, 1.250000000000000000 ) ) ; +#74756 = LINE ( 'NONE', #20102, #98834 ) ; +#74757 = CARTESIAN_POINT ( 'NONE', ( 0.9238200612200860862, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#74758 = EDGE_LOOP ( 'NONE', ( #6454, #4438, #8395, #2191 ) ) ; +#74759 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#74760 = PLANE ( 'NONE', #14437 ) ; +#74761 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8191, 'distance_accuracy_value', 'NONE'); +#74762 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #46631, .NOT_KNOWN. ) ; +#74763 = LINE ( 'NONE', #81942, #53654 ) ; +#74764 = VECTOR ( 'NONE', #12629, 1000.000000000000000 ) ; +#74765 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#74766 = ORIENTED_EDGE ( 'NONE', *, *, #41273, .F. ) ; +#74767 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#74768 = LINE ( 'NONE', #73760, #81021 ) ; +#74769 = LINE ( 'NONE', #83436, #82153 ) ; +#74770 = VECTOR ( 'NONE', #46951, 1000.000000000000000 ) ; +#74771 = FILL_AREA_STYLE_COLOUR ( '', #57215 ) ; +#74772 = CARTESIAN_POINT ( 'NONE', ( 0.2900000000000000355, -0.01499999999999999771, -0.1458578643762691029 ) ) ; +#74773 = VERTEX_POINT ( 'NONE', #65890 ) ; +#74774 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16061 ) ) ; +#74775 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#74776 = EDGE_CURVE ( 'NONE', #60726, #36865, #82710, .T. ) ; +#74777 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63932, 'distance_accuracy_value', 'NONE'); +#74779 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74778 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95946 ), #89415 ) ; +#74780 = ORIENTED_EDGE ( 'NONE', *, *, #65678, .T. ) ; +#74781 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74782 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#74783 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.300000000000000266, 0.1829999999999870064 ) ) ; +#74784 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74785 = ORIENTED_EDGE ( 'NONE', *, *, #93642, .T. ) ; +#74786 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220085265, 2.700000000000000178, 0.000000000000000000 ) ) ; +#74787 = ADVANCED_FACE ( 'NONE', ( #21415 ), #27102, .T. ) ; +#74788 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74789 = STYLED_ITEM ( 'NONE', ( #46585 ), #63340 ) ; +#74790 = AXIS2_PLACEMENT_3D ( 'NONE', #83995, #45147, #5830 ) ; +#74791 = ORIENTED_EDGE ( 'NONE', *, *, #556, .F. ) ; +#74793 = ORIENTED_EDGE ( 'NONE', *, *, #19654, .T. ) ; +#74792 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74794 = CIRCLE ( 'NONE', #30737, 0.1000000000000000056 ) ; +#74795 = CARTESIAN_POINT ( 'NONE', ( 2.818156000000000105, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#74797 = CARTESIAN_POINT ( 'NONE', ( -1.394210630085580105, -1.326636125966530244, 0.8299999999999999600 ) ) ; +#74796 = SURFACE_STYLE_USAGE ( .BOTH. , #60004 ) ; +#74798 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#74799 = LINE ( 'NONE', #51827, #76421 ) ; +#74800 = FACE_OUTER_BOUND ( 'NONE', #42032, .T. ) ; +#74801 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74802 = EDGE_LOOP ( 'NONE', ( #70356, #5817, #47372, #22207 ) ) ; +#74803 = PRESENTATION_STYLE_ASSIGNMENT (( #59532 ) ) ; +#74804 = LINE ( 'NONE', #52340, #1023 ) ; +#74805 = ORIENTED_EDGE ( 'NONE', *, *, #88165, .F. ) ; +#74807 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#74806 = SURFACE_STYLE_FILL_AREA ( #2859 ) ; +#74808 = EDGE_LOOP ( 'NONE', ( #82503, #29300, #97366, #24022, #82346, #43519 ) ) ; +#74809 = VECTOR ( 'NONE', #3907, 1000.000000000000000 ) ; +#74810 = SURFACE_STYLE_USAGE ( .BOTH. , #21684 ) ; +#74811 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65049 ), #3100 ) ; +#74812 = FILL_AREA_STYLE ('',( #67619 ) ) ; +#74813 = LINE ( 'NONE', #98214, #71850 ) ; +#74814 = AXIS2_PLACEMENT_3D ( 'NONE', #38334, #31165, #88318 ) ; +#74815 = ORIENTED_EDGE ( 'NONE', *, *, #16835, .T. ) ; +#74816 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999999112, 0.7578679656440356904, 0.1999999999999998723 ) ) ; +#74817 = VERTEX_POINT ( 'NONE', #38744 ) ; +#74818 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74819 = EDGE_CURVE ( 'NONE', #88638, #20936, #83720, .T. ) ; +#74820 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74821 = FILL_AREA_STYLE_COLOUR ( '', #92521 ) ; +#74822 = VECTOR ( 'NONE', #32437, 1000.000000000000000 ) ; +#74823 = VECTOR ( 'NONE', #94848, 1000.000000000000000 ) ; +#74824 = PLANE ( 'NONE', #82201 ) ; +#74825 = FILL_AREA_STYLE ('',( #6311 ) ) ; +#74826 = LINE ( 'NONE', #25874, #22596 ) ; +#74827 = VECTOR ( 'NONE', #60541, 1000.000000000000000 ) ; +#74828 = VECTOR ( 'NONE', #45800, 1000.000000000000000 ) ; +#74829 = ORIENTED_EDGE ( 'NONE', *, *, #75241, .T. ) ; +#74830 = PRESENTATION_STYLE_ASSIGNMENT (( #82504 ) ) ; +#74832 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74831 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74833 = STYLED_ITEM ( 'NONE', ( #62004 ), #56996 ) ; +#74834 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74835 = CIRCLE ( 'NONE', #78118, 0.09999999999999939493 ) ; +#74836 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1457 ) ) ; +#74837 = LINE ( 'NONE', #27381, #24029 ) ; +#74838 = FILL_AREA_STYLE_COLOUR ( '', #7682 ) ; +#74839 = SURFACE_STYLE_USAGE ( .BOTH. , #5351 ) ; +#74841 = ORIENTED_EDGE ( 'NONE', *, *, #55873, .F. ) ; +#74840 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17748 ) ) ; +#74842 = FILL_AREA_STYLE ('',( #43681 ) ) ; +#74843 = EDGE_CURVE ( 'NONE', #5540, #77757, #45363, .T. ) ; +#74844 = VECTOR ( 'NONE', #95956, 1000.000000000000000 ) ; +#74845 = PLANE ( 'NONE', #79911 ) ; +#74846 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1399999999999999856 ) ) ; +#74847 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74848 = FILL_AREA_STYLE ('',( #36066 ) ) ; +#74849 = AXIS2_PLACEMENT_3D ( 'NONE', #48492, #1509, #26508 ) ; +#74850 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74851 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#74852 = FILL_AREA_STYLE ('',( #84021 ) ) ; +#74853 = SURFACE_STYLE_USAGE ( .BOTH. , #91656 ) ; +#74854 = EDGE_CURVE ( 'NONE', #55021, #67280, #46888, .T. ) ; +#74855 = FILL_AREA_STYLE ('',( #43693 ) ) ; +#74856 = SURFACE_STYLE_FILL_AREA ( #84509 ) ; +#74857 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74858 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.699999999999999734, 0.1829999999999999960 ) ) ; +#74859 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74860 = FILL_AREA_STYLE ('',( #74366 ) ) ; +#74861 = VECTOR ( 'NONE', #89029, 1000.000000000000114 ) ; +#74862 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74863 = STYLED_ITEM ( 'NONE', ( #60960 ), #42416 ) ; +#74864 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#74865 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16958, 'distance_accuracy_value', 'NONE'); +#74866 = LINE ( 'NONE', #98268, #25059 ) ; +#74867 = FACE_OUTER_BOUND ( 'NONE', #48194, .T. ) ; +#74868 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74869 = CARTESIAN_POINT ( 'NONE', ( 3.277775124875012214, 5.988376124875013140, 0.8991599999999999593 ) ) ; +#74870 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57872 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5578, #28119, #50116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74871 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#74872 = ADVANCED_FACE ( 'NONE', ( #61754 ), #14206, .T. ) ; +#74873 = ORIENTED_EDGE ( 'NONE', *, *, #6409, .T. ) ; +#74874 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74875 = EDGE_CURVE ( 'NONE', #20018, #49182, #1150, .T. ) ; +#74876 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69419, 'distance_accuracy_value', 'NONE'); +#74877 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9330, 'distance_accuracy_value', 'NONE'); +#74879 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#74878 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74880 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52012 ), #56983 ) ; +#74881 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#74882 = STYLED_ITEM ( 'NONE', ( #98632 ), #15443 ) ; +#74883 = LINE ( 'NONE', #36100, #91721 ) ; +#74884 = CARTESIAN_POINT ( 'NONE', ( 0.4139933895064480396, -0.9720529820698129431, 0.8100000000000002753 ) ) ; +#74885 = ORIENTED_EDGE ( 'NONE', *, *, #28855, .F. ) ; +#74886 = CARTESIAN_POINT ( 'NONE', ( 3.539404999999999912, 4.807508000000000337, 0.8991599999999999593 ) ) ; +#74887 = FILL_AREA_STYLE ('',( #12002 ) ) ; +#74888 = VERTEX_POINT ( 'NONE', #85191 ) ; +#74889 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17796 ) ) ; +#74890 = ADVANCED_FACE ( 'NONE', ( #52578 ), #14716, .F. ) ; +#74891 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80666, 'distance_accuracy_value', 'NONE'); +#74892 = SURFACE_STYLE_USAGE ( .BOTH. , #83055 ) ; +#74893 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71700, 'distance_accuracy_value', 'NONE'); +#74894 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74895 = PRESENTATION_STYLE_ASSIGNMENT (( #43728 ) ) ; +#74896 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#74897 = ORIENTED_EDGE ( 'NONE', *, *, #99366, .F. ) ; +#74898 = EDGE_LOOP ( 'NONE', ( #11366, #8688, #79339, #94041 ) ) ; +#74899 = FACE_OUTER_BOUND ( 'NONE', #2456, .T. ) ; +#74900 = SURFACE_SIDE_STYLE ('',( #50937 ) ) ; +#74901 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29271 ), #58682 ) ; +#74902 = VERTEX_POINT ( 'NONE', #8010 ) ; +#74903 = CARTESIAN_POINT ( 'NONE', ( 1.814236996624309928, -1.283680827045210027, 0.8100000000000010525 ) ) ; +#74904 = STYLED_ITEM ( 'NONE', ( #38508 ), #75475 ) ; +#74905 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8100000000000000533 ) ) ; +#74906 = SURFACE_STYLE_USAGE ( .BOTH. , #58612 ) ; +#74907 = SURFACE_STYLE_FILL_AREA ( #43741 ) ; +#74908 = SURFACE_SIDE_STYLE ('',( #66723 ) ) ; +#74909 = EDGE_CURVE ( 'NONE', #94835, #44546, #48748, .T. ) ; +#74910 = AXIS2_PLACEMENT_3D ( 'NONE', #11474, #97304, #27400 ) ; +#74911 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #1288, #42085 ) ; +#74912 = LINE ( 'NONE', #73908, #26499 ) ; +#74914 = ORIENTED_EDGE ( 'NONE', *, *, #30927, .F. ) ; +#74913 = ORIENTED_EDGE ( 'NONE', *, *, #57761, .F. ) ; +#74915 = VERTEX_POINT ( 'NONE', #70374 ) ; +#74916 = STYLED_ITEM ( 'NONE', ( #43406 ), #57426 ) ; +#74917 = ORIENTED_EDGE ( 'NONE', *, *, #14642, .T. ) ; +#74919 = SURFACE_STYLE_FILL_AREA ( #4444 ) ; +#74918 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63565 ) ) ; +#74920 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17826 ), #66732 ) ; +#74921 = FACE_OUTER_BOUND ( 'NONE', #6977, .T. ) ; +#74923 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74922 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74924 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #74015, #43361, #44342, #5029 ), + ( #96959, #75509, #20885, #74529 ), + ( #36228, #35736, #67335, #98405 ), + ( #28544, #90838, #52055, #83189 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#74925 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84169 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82038, #60079, #21230 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74926 = AXIS2_PLACEMENT_3D ( 'NONE', #76209, #45522, #59442 ) ; +#74927 = CARTESIAN_POINT ( 'NONE', ( -1.162261078148919990, -0.8845231535185279492, 0.8299999999999999600 ) ) ; +#74928 = ORIENTED_EDGE ( 'NONE', *, *, #53778, .F. ) ; +#74930 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#74929 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#74931 = ORIENTED_EDGE ( 'NONE', *, *, #43181, .F. ) ; +#74932 = ORIENTED_EDGE ( 'NONE', *, *, #78042, .T. ) ; +#74933 = CARTESIAN_POINT ( 'NONE', ( 1.207735270546159922, -1.226800916006800080, 0.8100000000000000533 ) ) ; +#74934 = EDGE_CURVE ( 'NONE', #30014, #25174, #49435, .T. ) ; +#74936 = SURFACE_STYLE_USAGE ( .BOTH. , #100287 ) ; +#74935 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#74937 = CARTESIAN_POINT ( 'NONE', ( 1.818850168448489901, -1.194792006717259936, 0.8300000000000004041 ) ) ; +#74938 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37502 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99096, #39280, #77593 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74939 = SURFACE_SIDE_STYLE ('',( #52974 ) ) ; +#74941 = ORIENTED_EDGE ( 'NONE', *, *, #90802, .T. ) ; +#74940 = SURFACE_STYLE_USAGE ( .BOTH. , #82110 ) ; +#74942 = VECTOR ( 'NONE', #79505, 1000.000000000000000 ) ; +#74943 = VERTEX_POINT ( 'NONE', #25467 ) ; +#74944 = FILL_AREA_STYLE_COLOUR ( '', #62950 ) ; +#74945 = ORIENTED_EDGE ( 'NONE', *, *, #41143, .T. ) ; +#74947 = FILL_AREA_STYLE ('',( #76429 ) ) ; +#74946 = LINE ( 'NONE', #67263, #67750 ) ; +#74948 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89594 ) ) ; +#74949 = PRESENTATION_STYLE_ASSIGNMENT (( #19816 ) ) ; +#74950 = EDGE_LOOP ( 'NONE', ( #43614, #46263, #49088, #97967 ) ) ; +#74951 = ORIENTED_EDGE ( 'NONE', *, *, #66355, .T. ) ; +#74952 = ADVANCED_FACE ( 'NONE', ( #87731 ), #80093, .T. ) ; +#74954 = SURFACE_STYLE_USAGE ( .BOTH. , #43790 ) ; +#74953 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#74955 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#74956 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#74957 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#74958 = STYLED_ITEM ( 'NONE', ( #28144 ), #51053 ) ; +#74959 = PLANE ( 'NONE', #73592 ) ; +#74960 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#74961 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2166666666666660079, 0.000000000000000000 ) ) ; +#74962 = VERTEX_POINT ( 'NONE', #41782 ) ; +#74963 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#74964 = ORIENTED_EDGE ( 'NONE', *, *, #29724, .F. ) ; +#74965 = LINE ( 'NONE', #59180, #89716 ) ; +#74966 = CARTESIAN_POINT ( 'NONE', ( -0.03785612751057330916, -0.9872600217210630857, 0.8100000000000000533 ) ) ; +#74967 = VECTOR ( 'NONE', #21752, 1000.000000000000000 ) ; +#74968 = CARTESIAN_POINT ( 'NONE', ( 1.432999986405000037, -1.279077976066830047, 0.8100000000000000533 ) ) ; +#74969 = FACE_OUTER_BOUND ( 'NONE', #53060, .T. ) ; +#74970 = SURFACE_STYLE_FILL_AREA ( #95902 ) ; +#74971 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935067599, 0.8100000000000000533 ) ) ; +#74972 = FILL_AREA_STYLE_COLOUR ( '', #9115 ) ; +#74973 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#74974 = ORIENTED_EDGE ( 'NONE', *, *, #80915, .T. ) ; +#74975 = CARTESIAN_POINT ( 'NONE', ( 0.1950603093179809899, -0.9901296077683260366, 0.8100000000000000533 ) ) ; +#74976 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33693 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77125, #30640, #17222 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#74977 = SURFACE_STYLE_USAGE ( .BOTH. , #28507 ) ; +#74978 = CARTESIAN_POINT ( 'NONE', ( 1.319977302430629162, -1.497085791687843281, 0.8099999999996775335 ) ) ; +#74979 = CARTESIAN_POINT ( 'NONE', ( 1.901168164643999958, -1.316888414733939916, 0.8100000000000000533 ) ) ; +#74980 = EDGE_CURVE ( 'NONE', #37298, #5457, #55107, .T. ) ; +#74981 = EDGE_CURVE ( 'NONE', #62227, #18656, #17754, .T. ) ; +#74982 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39110 ), #6393 ) ; +#74983 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74984 = FILL_AREA_STYLE_COLOUR ( '', #58729 ) ; +#74985 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#74986 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#74987 = SURFACE_STYLE_USAGE ( .BOTH. , #21856 ) ; +#74988 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#74989 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#74990 = VECTOR ( 'NONE', #53299, 1000.000000000000000 ) ; +#74991 = VECTOR ( 'NONE', #69954, 1000.000000000000000 ) ; +#74992 = FILL_AREA_STYLE_COLOUR ( '', #11015 ) ; +#74993 = VECTOR ( 'NONE', #92491, 1000.000000000000000 ) ; +#74994 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4662, 'distance_accuracy_value', 'NONE'); +#74995 = VECTOR ( 'NONE', #5621, 1000.000000000000000 ) ; +#74996 = VERTEX_POINT ( 'NONE', #48943 ) ; +#74997 = CARTESIAN_POINT ( 'NONE', ( 0.02152160799746852607, -1.471934987032784914, 0.8099999999995407540 ) ) ; +#74998 = CARTESIAN_POINT ( 'NONE', ( -0.9563262017851451580, -0.9843154279477429602, 0.8099999999999997202 ) ) ; +#74999 = EDGE_CURVE ( 'NONE', #66135, #10511, #18254, .T. ) ; +#75000 = ORIENTED_EDGE ( 'NONE', *, *, #50094, .F. ) ; +#75001 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#75002 = SURFACE_SIDE_STYLE ('',( #92771 ) ) ; +#75003 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #791, #8369, #53422 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75004 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#75005 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75006 = ADVANCED_FACE ( 'NONE', ( #41288 ), #9030, .T. ) ; +#75007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75008 = VECTOR ( 'NONE', #35826, 1000.000000000000000 ) ; +#75009 = LINE ( 'NONE', #28051, #11630 ) ; +#75010 = EDGE_CURVE ( 'NONE', #93666, #28002, #79075, .T. ) ; +#75011 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, 0.05000000000000000278, 0.08229670385730990245 ) ) ; +#75012 = PLANE ( 'NONE', #14528 ) ; +#75013 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#75014 = ORIENTED_EDGE ( 'NONE', *, *, #63601, .F. ) ; +#75015 = EDGE_LOOP ( 'NONE', ( #76229, #93855, #48155, #91305 ) ) ; +#75016 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92875 ) ) ; +#75017 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#75018 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55444 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72939, #70922, #74953 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75019 = SURFACE_STYLE_USAGE ( .BOTH. , #4048 ) ; +#75020 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63594 ), #6426 ) ; +#75021 = SURFACE_STYLE_FILL_AREA ( #12649 ) ; +#75022 = ADVANCED_FACE ( 'NONE', ( #40277 ), #1970, .T. ) ; +#75023 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94846, 'distance_accuracy_value', 'NONE'); +#75024 = FILL_AREA_STYLE ('',( #83681 ) ) ; +#75025 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59080, 'distance_accuracy_value', 'NONE'); +#75026 = CARTESIAN_POINT ( 'NONE', ( -2.215999996349471424E-07, -0.1350001193000001376, 0.1499999999999999667 ) ) ; +#75027 = FILL_AREA_STYLE_COLOUR ( '', #18424 ) ; +#75028 = VERTEX_POINT ( 'NONE', #24971 ) ; +#75029 = EDGE_CURVE ( 'NONE', #57125, #69445, #57122, .T. ) ; +#75030 = VERTEX_POINT ( 'NONE', #24472 ) ; +#75031 = AXIS2_PLACEMENT_3D ( 'NONE', #25579, #50576, #11149 ) ; +#75032 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #22521, #77149, #47518, #23550 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#75033 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75034 = EDGE_LOOP ( 'NONE', ( #80944, #16014, #76177, #28933 ) ) ; +#75036 = PLANE ( 'NONE', #21596 ) ; +#75035 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81801 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29513, #69802, #93266 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75037 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#75038 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75039 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48948 ) ) ; +#75040 = SURFACE_STYLE_FILL_AREA ( #76511 ) ; +#75041 = EDGE_CURVE ( 'NONE', #34720, #65675, #23966, .T. ) ; +#75042 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75043 = CARTESIAN_POINT ( 'NONE', ( -0.3666260071936779941, -1.058874572656040014, 0.8299999999999999600 ) ) ; +#75044 = CARTESIAN_POINT ( 'NONE', ( -1.242030017193550107, -0.9708075278790050389, 0.8100000000000000533 ) ) ; +#75045 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766240006, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#75046 = ADVANCED_FACE ( 'NONE', ( #65247 ), #47413, .T. ) ; +#75048 = ORIENTED_EDGE ( 'NONE', *, *, #19117, .T. ) ; +#75047 = ORIENTED_EDGE ( 'NONE', *, *, #20910, .T. ) ; +#75049 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75050 = ORIENTED_EDGE ( 'NONE', *, *, #414, .T. ) ; +#75051 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75053 = PRESENTATION_STYLE_ASSIGNMENT (( #82697 ) ) ; +#75052 = PLANE ( 'NONE', #45816 ) ; +#75054 = ORIENTED_EDGE ( 'NONE', *, *, #41503, .F. ) ; +#75055 = ORIENTED_EDGE ( 'NONE', *, *, #79816, .T. ) ; +#75056 = SURFACE_SIDE_STYLE ('',( #65882 ) ) ; +#75057 = FILL_AREA_STYLE_COLOUR ( '', #67508 ) ; +#75058 = LINE ( 'NONE', #35272, #7836 ) ; +#75059 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14712 ), #66941 ) ; +#75060 = PLANE ( 'NONE', #9062 ) ; +#75061 = ORIENTED_EDGE ( 'NONE', *, *, #85444, .F. ) ; +#75062 = ORIENTED_EDGE ( 'NONE', *, *, #55764, .F. ) ; +#75063 = SURFACE_STYLE_FILL_AREA ( #82224 ) ; +#75064 = ORIENTED_EDGE ( 'NONE', *, *, #42844, .F. ) ; +#75065 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75066 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75067 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26163 ), #78332 ) ; +#75068 = EDGE_CURVE ( 'NONE', #25637, #10232, #58636, .T. ) ; +#75069 = FACE_OUTER_BOUND ( 'NONE', #69019, .T. ) ; +#75070 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75072 = EDGE_LOOP ( 'NONE', ( #26390, #3801, #49917, #65217 ) ) ; +#75071 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75073 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#75074 = CARTESIAN_POINT ( 'NONE', ( 2.433333333333326465, 3.500000000000000000, 0.000000000000000000 ) ) ; +#75075 = VERTEX_POINT ( 'NONE', #36141 ) ; +#75076 = AXIS2_PLACEMENT_3D ( 'NONE', #91741, #28973, #99338 ) ; +#75077 = SURFACE_STYLE_FILL_AREA ( #74571 ) ; +#75078 = ORIENTED_EDGE ( 'NONE', *, *, #9867, .F. ) ; +#75079 = ORIENTED_EDGE ( 'NONE', *, *, #24772, .F. ) ; +#75080 = ADVANCED_FACE ( 'NONE', ( #43267 ), #73431, .T. ) ; +#75081 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 13.09601199999999999, 0.8648700000000000276 ) ) ; +#75082 = AXIS2_PLACEMENT_3D ( 'NONE', #53308, #670, #31821 ) ; +#75083 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#75084 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75085 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75086 = EDGE_CURVE ( 'NONE', #72705, #36325, #90233, .T. ) ; +#75087 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.000000000000000000 ) ) ; +#75088 = SURFACE_STYLE_USAGE ( .BOTH. , #12711 ) ; +#75090 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#75089 = FILL_AREA_STYLE ('',( #97522 ) ) ; +#75091 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#75092 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27797 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95143, #2767, #25271 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75093 = ORIENTED_EDGE ( 'NONE', *, *, #17600, .T. ) ; +#75094 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75095 = CARTESIAN_POINT ( 'NONE', ( -1.043371449138229989, -1.500691070757680157, 0.8299999999999999600 ) ) ; +#75096 = EDGE_LOOP ( 'NONE', ( #36593, #48827, #86009, #28214 ) ) ; +#75097 = VECTOR ( 'NONE', #97837, 1000.000000000000000 ) ; +#75098 = PRESENTATION_STYLE_ASSIGNMENT (( #5093 ) ) ; +#75099 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79984 ) ) ; +#75100 = PLANE ( 'NONE', #90719 ) ; +#75101 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#75102 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75104 = SURFACE_STYLE_USAGE ( .BOTH. , #85621 ) ; +#75103 = FACE_OUTER_BOUND ( 'NONE', #71793, .T. ) ; +#75105 = SURFACE_STYLE_FILL_AREA ( #84252 ) ; +#75106 = FILL_AREA_STYLE ('',( #34314 ) ) ; +#75107 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26208 ), #73501 ) ; +#75108 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75109 = ADVANCED_FACE ( 'NONE', ( #27470 ), #49962, .F. ) ; +#75110 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.300000000000000044, -0.02000000000000000042 ) ) ; +#75111 = SURFACE_SIDE_STYLE ('',( #20455 ) ) ; +#75112 = SURFACE_STYLE_USAGE ( .BOTH. , #13231 ) ; +#75113 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75114 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28859, 'distance_accuracy_value', 'NONE'); +#75115 = VERTEX_POINT ( 'NONE', #81101 ) ; +#75116 = CARTESIAN_POINT ( 'NONE', ( -1.027917449215540069, -1.416724300735810127, 0.8299999999999999600 ) ) ; +#75117 = LINE ( 'NONE', #69809, #22843 ) ; +#75118 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, -3.099999999999980549, 0.000000000000000000 ) ) ; +#75119 = ADVANCED_FACE ( 'NONE', ( #42777 ), #73923, .T. ) ; +#75120 = SURFACE_STYLE_USAGE ( .BOTH. , #45926 ) ; +#75121 = LINE ( 'NONE', #51660, #86069 ) ; +#75122 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75123 = VECTOR ( 'NONE', #18088, 1000.000000000000000 ) ; +#75124 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#75125 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#75126 = FACE_OUTER_BOUND ( 'NONE', #78649, .T. ) ; +#75127 = PRODUCT ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_XTAL3225_20210301.STEP', 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_XTAL3225_20210301.STEP', '', ( #16210 ) ) ; +#75128 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75129 = AXIS2_PLACEMENT_3D ( 'NONE', #21716, #92159, #37070 ) ; +#75130 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#75131 = ORIENTED_EDGE ( 'NONE', *, *, #35788, .T. ) ; +#75132 = PLANE ( 'NONE', #46492 ) ; +#75133 = VERTEX_POINT ( 'NONE', #46242 ) ; +#75134 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000001110, -0.005000000000000004441, -0.2399999999999999911 ) ) ; +#75135 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85316, 'distance_accuracy_value', 'NONE'); +#75136 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#75137 = SURFACE_STYLE_USAGE ( .BOTH. , #21002 ) ; +#75138 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22948 ) ) ; +#75139 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#75140 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#75141 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75142 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75143 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75144 = PLANE ( 'NONE', #6004 ) ; +#75145 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#75146 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#75147 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68540 ), #88193 ) ; +#75148 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75149 = VERTEX_POINT ( 'NONE', #38135 ) ; +#75150 = SURFACE_STYLE_FILL_AREA ( #84297 ) ; +#75151 = AXIS2_PLACEMENT_3D ( 'NONE', #23421, #94345, #93320 ) ; +#75152 = SURFACE_SIDE_STYLE ('',( #67941 ) ) ; +#75153 = EDGE_LOOP ( 'NONE', ( #48942, #22279, #37850, #87923 ) ) ; +#75154 = FACE_OUTER_BOUND ( 'NONE', #52160, .T. ) ; +#75155 = FILL_AREA_STYLE ('',( #29661 ) ) ; +#75156 = AXIS2_PLACEMENT_3D ( 'NONE', #49771, #89056, #19085 ) ; +#75157 = ORIENTED_EDGE ( 'NONE', *, *, #7396, .F. ) ; +#75158 = DIRECTION ( 'NONE', ( 0.7071060119555137025, 0.7071075504167445569, 0.000000000000000000 ) ) ; +#75159 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#75160 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62199 ) ) ; +#75161 = CARTESIAN_POINT ( 'NONE', ( -8.673617379884035472E-16, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75162 = PRESENTATION_STYLE_ASSIGNMENT (( #99528 ) ) ; +#75163 = VECTOR ( 'NONE', #29265, 1000.000000000000000 ) ; +#75164 = EDGE_CURVE ( 'NONE', #14941, #41816, #6416, .T. ) ; +#75165 = ORIENTED_EDGE ( 'NONE', *, *, #58231, .F. ) ; +#75166 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47375 ) ) ; +#75167 = LINE ( 'NONE', #5156, #1751 ) ; +#75168 = SURFACE_STYLE_FILL_AREA ( #29675 ) ; +#75169 = ORIENTED_EDGE ( 'NONE', *, *, #54215, .F. ) ; +#75170 = PLANE ( 'NONE', #6647 ) ; +#75171 = ORIENTED_EDGE ( 'NONE', *, *, #3443, .F. ) ; +#75172 = VERTEX_POINT ( 'NONE', #23315 ) ; +#75173 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75174 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#75175 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75176 = STYLED_ITEM ( 'NONE', ( #10338 ), #51628 ) ; +#75177 = CARTESIAN_POINT ( 'NONE', ( -1.816666666666666652, -3.099999999999989875, 0.000000000000000000 ) ) ; +#75178 = ORIENTED_EDGE ( 'NONE', *, *, #80544, .F. ) ; +#75179 = ORIENTED_EDGE ( 'NONE', *, *, #57813, .T. ) ; +#75180 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93109 ) ) ; +#75181 = VERTEX_POINT ( 'NONE', #100281 ) ; +#75182 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40847 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88463, #50204, #25687 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75183 = FACE_OUTER_BOUND ( 'NONE', #82709, .T. ) ; +#75184 = ADVANCED_FACE ( 'NONE', ( #30963 ), #69746, .T. ) ; +#75185 = VECTOR ( 'NONE', #84300, 1000.000000000000000 ) ; +#75186 = ORIENTED_EDGE ( 'NONE', *, *, #25064, .F. ) ; +#75187 = FACE_OUTER_BOUND ( 'NONE', #63781, .T. ) ; +#75188 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75189 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75190 = FILL_AREA_STYLE_COLOUR ( '', #32574 ) ; +#75191 = ORIENTED_EDGE ( 'NONE', *, *, #59560, .T. ) ; +#75192 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75193 = CARTESIAN_POINT ( 'NONE', ( 1.296446609406726402, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#75194 = ORIENTED_EDGE ( 'NONE', *, *, #81182, .F. ) ; +#75195 = ADVANCED_FACE ( 'NONE', ( #93202 ), #77930, .T. ) ; +#75196 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109696999999998823, 0.8991599999999999593 ) ) ; +#75197 = CARTESIAN_POINT ( 'NONE', ( 0.5451074176016761363, -1.092033457943389907, 0.8299999999999999600 ) ) ; +#75198 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4399 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50324, #49802, #57464 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75199 = SURFACE_STYLE_FILL_AREA ( #85720 ) ; +#75200 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75201 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93066 ) ) ; +#75202 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87404 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70185, #55420, #71205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75204 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#75203 = LINE ( 'NONE', #5195, #7164 ) ; +#75205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75206 = ORIENTED_EDGE ( 'NONE', *, *, #89343, .F. ) ; +#75207 = EDGE_CURVE ( 'NONE', #93723, #48662, #9420, .T. ) ; +#75208 = AXIS2_PLACEMENT_3D ( 'NONE', #41174, #81991, #97261 ) ; +#75209 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4808578643762689842, -0.2400000000000000189 ) ) ; +#75210 = VECTOR ( 'NONE', #25149, 1000.000000000000000 ) ; +#75211 = CARTESIAN_POINT ( 'NONE', ( 1.186840394175660007, -1.149778012002649952, 0.8300000000000022915 ) ) ; +#75212 = EDGE_CURVE ( 'NONE', #72987, #27266, #55492, .T. ) ; +#75213 = CARTESIAN_POINT ( 'NONE', ( 0.4656308297546359887, -1.047495427385189970, 0.8100000000000000533 ) ) ; +#75214 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75215 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#75216 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75217 = LINE ( 'NONE', #5208, #59118 ) ; +#75218 = VECTOR ( 'NONE', #67205, 1000.000000000000000 ) ; +#75219 = VECTOR ( 'NONE', #98500, 1000.000000000000000 ) ; +#75220 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75221 = ORIENTED_EDGE ( 'NONE', *, *, #100785, .T. ) ; +#75222 = FILL_AREA_STYLE ('',( #44052 ) ) ; +#75223 = EDGE_CURVE ( 'NONE', #46528, #19290, #63646, .T. ) ; +#75224 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75225 = EDGE_CURVE ( 'NONE', #14953, #48692, #1336, .T. ) ; +#75226 = LINE ( 'NONE', #46942, #67957 ) ; +#75227 = ORIENTED_EDGE ( 'NONE', *, *, #28589, .T. ) ; +#75228 = VECTOR ( 'NONE', #54123, 1000.000000000000000 ) ; +#75229 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#75230 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75231 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88278 ), #99532 ) ; +#75232 = EDGE_CURVE ( 'NONE', #91841, #67222, #87609, .T. ) ; +#75234 = EDGE_CURVE ( 'NONE', #33091, #19242, #79971, .T. ) ; +#75233 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75235 = PLANE ( 'NONE', #12734 ) ; +#75236 = ORIENTED_EDGE ( 'NONE', *, *, #25509, .T. ) ; +#75237 = PRESENTATION_STYLE_ASSIGNMENT (( #13878 ) ) ; +#75238 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.4245906043549200204, -0.02000000000000000042 ) ) ; +#75239 = SURFACE_STYLE_USAGE ( .BOTH. , #44074 ) ; +#75240 = LINE ( 'NONE', #100090, #13934 ) ; +#75241 = EDGE_CURVE ( 'NONE', #52301, #53395, #49313, .T. ) ; +#75242 = SURFACE_STYLE_USAGE ( .BOTH. , #68041 ) ; +#75243 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75244 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#75245 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75246 = PLANE ( 'NONE', #77822 ) ; +#75247 = EDGE_CURVE ( 'NONE', #80432, #98364, #54976, .T. ) ; +#75248 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75249 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#75250 = ORIENTED_EDGE ( 'NONE', *, *, #30651, .T. ) ; +#75251 = ORIENTED_EDGE ( 'NONE', *, *, #93288, .F. ) ; +#75252 = VECTOR ( 'NONE', #64104, 1000.000000000000000 ) ; +#75253 = CYLINDRICAL_SURFACE ( 'NONE', #77940, 0.009999999999999998473 ) ; +#75254 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8100000000000000533 ) ) ; +#75255 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#75256 = SURFACE_STYLE_USAGE ( .BOTH. , #82917 ) ; +#75257 = LINE ( 'NONE', #20101, #43856 ) ; +#75258 = PRESENTATION_STYLE_ASSIGNMENT (( #76236 ) ) ; +#75259 = SURFACE_SIDE_STYLE ('',( #29772 ) ) ; +#75260 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#75261 = LINE ( 'NONE', #22123, #39537 ) ; +#75262 = ORIENTED_EDGE ( 'NONE', *, *, #55555, .T. ) ; +#75263 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75264 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42252 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94521, #87379, #17418 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75265 = AXIS2_PLACEMENT_3D ( 'NONE', #25679, #59867, #81826 ) ; +#75266 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8648700000000000276 ) ) ; +#75267 = EDGE_LOOP ( 'NONE', ( #93038, #68235, #90446, #66151 ) ) ; +#75268 = SURFACE_SIDE_STYLE ('',( #20621 ) ) ; +#75269 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75270 = STYLED_ITEM ( 'NONE', ( #12451 ), #86870 ) ; +#75271 = PLANE ( 'NONE', #90281 ) ; +#75272 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81852 ), #85012 ) ; +#75273 = PLANE ( 'NONE', #47257 ) ; +#75274 = FILL_AREA_STYLE ('',( #84918 ) ) ; +#75275 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#75276 = EDGE_CURVE ( 'NONE', #84446, #64838, #68318, .T. ) ; +#75277 = VERTEX_POINT ( 'NONE', #8393 ) ; +#75278 = VECTOR ( 'NONE', #63793, 1000.000000000000000 ) ; +#75279 = SURFACE_STYLE_FILL_AREA ( #27833 ) ; +#75280 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75281 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75282 = ADVANCED_FACE ( 'NONE', ( #78935 ), #56506, .T. ) ; +#75283 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8648700000000000276 ) ) ; +#75284 = AXIS2_PLACEMENT_3D ( 'NONE', #92094, #14460, #92581 ) ; +#75285 = ORIENTED_EDGE ( 'NONE', *, *, #64602, .F. ) ; +#75286 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#75287 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999994849, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#75288 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#75289 = CARTESIAN_POINT ( 'NONE', ( -1.028261076167377830, -1.264235153807178547, 0.8099999999997935518 ) ) ; +#75290 = PRESENTATION_STYLE_ASSIGNMENT (( #53803 ) ) ; +#75291 = ORIENTED_EDGE ( 'NONE', *, *, #10273, .T. ) ; +#75292 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75293 = VERTEX_POINT ( 'NONE', #17635 ) ; +#75295 = ORIENTED_EDGE ( 'NONE', *, *, #71120, .F. ) ; +#75294 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.123820061220065281, 0.000000000000000000 ) ) ; +#75296 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45591, 'distance_accuracy_value', 'NONE'); +#75297 = SURFACE_STYLE_USAGE ( .BOTH. , #52332 ) ; +#75298 = CARTESIAN_POINT ( 'NONE', ( -1.394210630085580105, -1.326636125966530244, 0.8100000000000000533 ) ) ; +#75299 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75300 = AXIS2_PLACEMENT_3D ( 'NONE', #24813, #61586, #55445 ) ; +#75301 = ORIENTED_EDGE ( 'NONE', *, *, #99156, .T. ) ; +#75302 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75303 = SURFACE_SIDE_STYLE ('',( #90622 ) ) ; +#75304 = ORIENTED_EDGE ( 'NONE', *, *, #98624, .T. ) ; +#75305 = ADVANCED_FACE ( 'NONE', ( #825 ), #95733, .T. ) ; +#75306 = CARTESIAN_POINT ( 'NONE', ( 1.289608948985750070, -1.506193478032149979, 0.8100000000000000533 ) ) ; +#75307 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75308 = ORIENTED_EDGE ( 'NONE', *, *, #86410, .T. ) ; +#75309 = VERTEX_POINT ( 'NONE', #41667 ) ; +#75310 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#75311 = VECTOR ( 'NONE', #94588, 1000.000000000000000 ) ; +#75312 = SURFACE_SIDE_STYLE ('',( #96753 ) ) ; +#75313 = LINE ( 'NONE', #28355, #1815 ) ; +#75314 = ORIENTED_EDGE ( 'NONE', *, *, #72110, .F. ) ; +#75315 = SURFACE_STYLE_USAGE ( .BOTH. , #58535 ) ; +#75316 = VERTEX_POINT ( 'NONE', #4350 ) ; +#75317 = SURFACE_STYLE_FILL_AREA ( #68639 ) ; +#75318 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75319 = VECTOR ( 'NONE', #57102, 1000.000000000000000 ) ; +#75320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75321 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 3.570070999999999994, 0.8991599999999999593 ) ) ; +#75322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99284 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52851, #6783, #60532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75323 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75324 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55667 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72869, #18196, #41730 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75325 = ORIENTED_EDGE ( 'NONE', *, *, #80265, .T. ) ; +#75326 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#75327 = CARTESIAN_POINT ( 'NONE', ( 1.334872846471060193, -1.409018172687890091, 0.8299999999999994049 ) ) ; +#75330 = PLANE ( 'NONE', #57422 ) ; +#75329 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75328 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75331 = AXIS2_PLACEMENT_3D ( 'NONE', #97830, #27972, #83081 ) ; +#75332 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21981, 'distance_accuracy_value', 'NONE'); +#75333 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.4600000000000000200, 1.129999999999999893 ) ) ; +#75335 = EDGE_CURVE ( 'NONE', #69132, #30580, #78108, .T. ) ; +#75334 = LINE ( 'NONE', #4869, #41376 ) ; +#75336 = AXIS2_PLACEMENT_3D ( 'NONE', #22802, #62629, #99776 ) ; +#75337 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75338 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#75339 = FILL_AREA_STYLE ('',( #99235 ) ) ; +#75340 = EDGE_LOOP ( 'NONE', ( #7677, #8764, #3949, #17868 ) ) ; +#75341 = STYLED_ITEM ( 'NONE', ( #76063 ), #7684 ) ; +#75342 = PRESENTATION_STYLE_ASSIGNMENT (( #37561 ) ) ; +#75343 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999802450, 0.2500000000000000000, 0.6499230723708768753 ) ) ; +#75344 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75345 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#75346 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75347 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#75348 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#75349 = SURFACE_SIDE_STYLE ('',( #22230 ) ) ; +#75350 = FACE_OUTER_BOUND ( 'NONE', #27472, .T. ) ; +#75351 = EDGE_CURVE ( 'NONE', #61838, #45984, #58020, .T. ) ; +#75352 = SURFACE_STYLE_FILL_AREA ( #99721 ) ; +#75353 = SURFACE_STYLE_USAGE ( .BOTH. , #85517 ) ; +#75354 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75355 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#75356 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#75357 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75358 = PLANE ( 'NONE', #86141 ) ; +#75359 = FILL_AREA_STYLE ('',( #5865 ) ) ; +#75360 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63929 ) ) ; +#75361 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.1499999999999999667, 0.1900000000000000022 ) ) ; +#75362 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#75363 = CARTESIAN_POINT ( 'NONE', ( 1.693812380665640216, -1.164588072778879990, 0.8299999999999997380 ) ) ; +#75364 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#75365 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#75366 = PRESENTATION_STYLE_ASSIGNMENT (( #68683 ) ) ; +#75367 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75368 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#75369 = VERTEX_POINT ( 'NONE', #43637 ) ; +#75370 = FILL_AREA_STYLE ('',( #4406 ) ) ; +#75371 = STYLED_ITEM ( 'NONE', ( #9334 ), #87715 ) ; +#75372 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#75373 = CARTESIAN_POINT ( 'NONE', ( -0.008099123004813310947, -1.050822088410799937, 0.8300000000000002931 ) ) ; +#75374 = LINE ( 'NONE', #5394, #57528 ) ; +#75375 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#75376 = EDGE_CURVE ( 'NONE', #62643, #98298, #66629, .T. ) ; +#75377 = ORIENTED_EDGE ( 'NONE', *, *, #98711, .T. ) ; +#75378 = SURFACE_STYLE_FILL_AREA ( #28912 ) ; +#75379 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#75380 = STYLED_ITEM ( 'NONE', ( #91961 ), #45774 ) ; +#75381 = ORIENTED_EDGE ( 'NONE', *, *, #89950, .F. ) ; +#75382 = CARTESIAN_POINT ( 'NONE', ( -0.1044034090909090329, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#75383 = FILL_AREA_STYLE ('',( #51927 ) ) ; +#75384 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75385 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75735 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46034, #92031, #38437 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75386 = ADVANCED_FACE ( 'NONE', ( #49838 ), #26349, .F. ) ; +#75387 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01499999999999999944, 0.2399999999999999911 ) ) ; +#75388 = ORIENTED_EDGE ( 'NONE', *, *, #10923, .T. ) ; +#75389 = ORIENTED_EDGE ( 'NONE', *, *, #7258, .T. ) ; +#75390 = STYLED_ITEM ( 'NONE', ( #96659 ), #18758 ) ; +#75391 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75392 = PLANE ( 'NONE', #71650 ) ; +#75393 = EDGE_LOOP ( 'NONE', ( #81833, #19155, #67531, #69960, #650 ) ) ; +#75394 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#75395 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000000222, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#75396 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75397 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90114 ) ) ; +#75398 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18308 ), #26520 ) ; +#75399 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #40444, #58257 ) ; +#75400 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#75402 = ORIENTED_EDGE ( 'NONE', *, *, #52554, .F. ) ; +#75401 = VERTEX_POINT ( 'NONE', #73311 ) ; +#75403 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57513 ), #6802 ) ; +#75404 = ORIENTED_EDGE ( 'NONE', *, *, #33364, .T. ) ; +#75405 = CYLINDRICAL_SURFACE ( 'NONE', #83366, 0.05000000000000002359 ) ; +#75406 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10170, 'distance_accuracy_value', 'NONE'); +#75407 = VECTOR ( 'NONE', #93076, 1000.000000000000000 ) ; +#75409 = CARTESIAN_POINT ( 'NONE', ( 1.320874515982729980, -0.9101533448649530289, 0.8299999999999999600 ) ) ; +#75408 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75410 = EDGE_CURVE ( 'NONE', #77743, #68999, #19152, .T. ) ; +#75411 = SURFACE_STYLE_FILL_AREA ( #89727 ) ; +#75412 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75413 = CARTESIAN_POINT ( 'NONE', ( -1.254664462595540098, -0.9005718509792439708, 0.8299999999999999600 ) ) ; +#75414 = AXIS2_PLACEMENT_3D ( 'NONE', #13011, #13518, #99742 ) ; +#75415 = ORIENTED_EDGE ( 'NONE', *, *, #77497, .F. ) ; +#75416 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.009999999999999998473, -1.250000000000000000 ) ) ; +#75417 = EDGE_CURVE ( 'NONE', #41000, #34733, #5974, .T. ) ; +#75418 = VERTEX_POINT ( 'NONE', #42664 ) ; +#75419 = VERTEX_POINT ( 'NONE', #66142 ) ; +#75420 = CARTESIAN_POINT ( 'NONE', ( 1.137573705260860102, -1.210702855844099979, 0.8299999999999999600 ) ) ; +#75421 = FACE_OUTER_BOUND ( 'NONE', #79416, .T. ) ; +#75422 = FILL_AREA_STYLE ('',( #44261 ) ) ; +#75423 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #55853, #49201, #1193, #72167 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#75424 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75425 = EDGE_LOOP ( 'NONE', ( #9837, #88344, #1782, #96495, #2487, #28111 ) ) ; +#75426 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#75427 = SURFACE_STYLE_USAGE ( .BOTH. , #36653 ) ; +#75428 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#75429 = VERTEX_POINT ( 'NONE', #90630 ) ; +#75431 = SURFACE_STYLE_USAGE ( .BOTH. , #29951 ) ; +#75430 = LINE ( 'NONE', #20809, #95663 ) ; +#75432 = SURFACE_STYLE_FILL_AREA ( #35163 ) ; +#75434 = VERTEX_POINT ( 'NONE', #73806 ) ; +#75433 = AXIS2_PLACEMENT_3D ( 'NONE', #53166, #68939, #47498 ) ; +#75435 = ORIENTED_EDGE ( 'NONE', *, *, #36389, .T. ) ; +#75436 = EDGE_CURVE ( 'NONE', #89235, #30702, #2441, .T. ) ; +#75437 = CARTESIAN_POINT ( 'NONE', ( 0.5141275518124609478, -0.9686402964547039529, 0.8299999999999992939 ) ) ; +#75438 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#75439 = EDGE_CURVE ( 'NONE', #41605, #16, #53334, .T. ) ; +#75440 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, 0.1500000000000000222 ) ) ; +#75441 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #17839, #17331, #79663, #34716 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#75442 = VECTOR ( 'NONE', #14889, 1000.000000000000000 ) ; +#75443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78749 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #92303, #52521, #53528 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75444 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041099999999908, 0.8991599999999999593 ) ) ; +#75445 = PLANE ( 'NONE', #71923 ) ; +#75447 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62419 ), #15118 ) ; +#75446 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8648700000000000276 ) ) ; +#75448 = CARTESIAN_POINT ( 'NONE', ( 0.01569390708528280165, 1.386225820966699995, 0.8100000000000000533 ) ) ; +#75449 = PRESENTATION_STYLE_ASSIGNMENT (( #6917 ) ) ; +#75450 = ORIENTED_EDGE ( 'NONE', *, *, #40669, .T. ) ; +#75451 = ORIENTED_EDGE ( 'NONE', *, *, #90253, .F. ) ; +#75452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75453 = SURFACE_SIDE_STYLE ('',( #4979 ) ) ; +#75455 = EDGE_CURVE ( 'NONE', #90468, #80272, #37016, .T. ) ; +#75454 = FILL_AREA_STYLE ('',( #58669 ) ) ; +#75456 = VECTOR ( 'NONE', #88162, 1000.000000000000000 ) ; +#75457 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11808 ), #52658 ) ; +#75458 = SURFACE_STYLE_USAGE ( .BOTH. , #44788 ) ; +#75459 = FILL_AREA_STYLE_COLOUR ( '', #35507 ) ; +#75460 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#75461 = SURFACE_STYLE_USAGE ( .BOTH. , #6453 ) ; +#75462 = ORIENTED_EDGE ( 'NONE', *, *, #97440, .F. ) ; +#75463 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75464 = PRESENTATION_STYLE_ASSIGNMENT (( #58677 ) ) ; +#75465 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83643 ) ) ; +#75466 = STYLED_ITEM ( 'NONE', ( #33804 ), #18948 ) ; +#75467 = VECTOR ( 'NONE', #26710, 1000.000000000000000 ) ; +#75468 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75469 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75470 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75472 = CARTESIAN_POINT ( 'NONE', ( 1.901254715655620098, -1.325441991778449902, 0.8299999999999999600 ) ) ; +#75471 = STYLED_ITEM ( 'NONE', ( #14741 ), #60605 ) ; +#75473 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86926 ) ) ; +#75474 = FILL_AREA_STYLE_COLOUR ( '', #87387 ) ; +#75475 = ADVANCED_FACE ( 'NONE', ( #99195 ), #84463, .F. ) ; +#75476 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46437 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25663, #59357, #99512 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75477 = SURFACE_SIDE_STYLE ('',( #81662 ) ) ; +#75478 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75479 = PLANE ( 'NONE', #14666 ) ; +#75480 = AXIS2_PLACEMENT_3D ( 'NONE', #15863, #39887, #56753 ) ; +#75481 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#75482 = VECTOR ( 'NONE', #89670, 1000.000000000000000 ) ; +#75483 = SURFACE_SIDE_STYLE ('',( #99850 ) ) ; +#75484 = AXIS2_PLACEMENT_3D ( 'NONE', #55114, #54078, #100890 ) ; +#75485 = ORIENTED_EDGE ( 'NONE', *, *, #23412, .F. ) ; +#75486 = LINE ( 'NONE', #5004, #2898 ) ; +#75487 = CARTESIAN_POINT ( 'NONE', ( 0.2314326298701300244, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#75488 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#75489 = ORIENTED_EDGE ( 'NONE', *, *, #80650, .T. ) ; +#75490 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75491 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37940 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21750, #83550, #51916 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75492 = EDGE_CURVE ( 'NONE', #48479, #46129, #30837, .T. ) ; +#75493 = PRESENTATION_STYLE_ASSIGNMENT (( #29034 ) ) ; +#75494 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36370 ) ) ; +#75495 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#75496 = ADVANCED_FACE ( 'NONE', ( #52343 ), #5815, .T. ) ; +#75497 = EDGE_LOOP ( 'NONE', ( #8853, #42735, #89462, #97834, #42779, #15005, #38641, #71004 ) ) ; +#75498 = SURFACE_SIDE_STYLE ('',( #4539 ) ) ; +#75499 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40227 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42307, #57137, #94376 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75500 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75501 = SURFACE_SIDE_STYLE ('',( #60220 ) ) ; +#75502 = PLANE ( 'NONE', #11900 ) ; +#75503 = PRESENTATION_STYLE_ASSIGNMENT (( #20880 ) ) ; +#75504 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75505 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65674 ) ) ; +#75506 = SHAPE_REPRESENTATION ( 'Submodel-C0402_part_C0402', ( #61511, #20663 ), #12433 ) ; +#75507 = EDGE_CURVE ( 'NONE', #97600, #17377, #54860, .T. ) ; +#75508 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75509 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01085786437626904723, 0.1499999999999999944 ) ) ; +#75510 = VERTEX_POINT ( 'NONE', #8780 ) ; +#75511 = ORIENTED_EDGE ( 'NONE', *, *, #94391, .T. ) ; +#75512 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49514 ) ) ; +#75513 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#75514 = ORIENTED_EDGE ( 'NONE', *, *, #27701, .T. ) ; +#75515 = SURFACE_STYLE_FILL_AREA ( #18863 ) ; +#75516 = CIRCLE ( 'NONE', #57636, 0.2500000000000001110 ) ; +#75517 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75518 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#75519 = LINE ( 'NONE', #20895, #80693 ) ; +#75520 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.950000000000000178, 0.000000000000000000 ) ) ; +#75521 = PLANE ( 'NONE', #76922 ) ; +#75522 = CARTESIAN_POINT ( 'NONE', ( -1.261022403107399992, -0.9825712221600161334, 0.8100000000000000533 ) ) ; +#75523 = SURFACE_STYLE_USAGE ( .BOTH. , #44356 ) ; +#75525 = VERTEX_POINT ( 'NONE', #39510 ) ; +#75524 = ORIENTED_EDGE ( 'NONE', *, *, #72679, .T. ) ; +#75526 = VERTEX_POINT ( 'NONE', #64014 ) ; +#75527 = CARTESIAN_POINT ( 'NONE', ( 9.252827999999999165, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#75529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29889 ) ) ; +#75528 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13735, 'distance_accuracy_value', 'NONE'); +#75530 = STYLED_ITEM ( 'NONE', ( #4400 ), #36264 ) ; +#75531 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25091, 'distance_accuracy_value', 'NONE'); +#75532 = ORIENTED_EDGE ( 'NONE', *, *, #99516, .T. ) ; +#75533 = VERTEX_POINT ( 'NONE', #78818 ) ; +#75534 = STYLED_ITEM ( 'NONE', ( #81471 ), #37759 ) ; +#75535 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#75536 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999983624, -0.1400000000000000411 ) ) ; +#75538 = PRESENTATION_STYLE_ASSIGNMENT (( #36256 ) ) ; +#75537 = LINE ( 'NONE', #90865, #41638 ) ; +#75539 = FILL_AREA_STYLE ('',( #67852 ) ) ; +#75540 = ORIENTED_EDGE ( 'NONE', *, *, #64956, .T. ) ; +#75541 = ORIENTED_EDGE ( 'NONE', *, *, #97883, .T. ) ; +#75542 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75543 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60002 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28979, #20822, #13080 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75544 = EDGE_CURVE ( 'NONE', #39524, #15979, #94625, .T. ) ; +#75545 = ORIENTED_EDGE ( 'NONE', *, *, #17912, .T. ) ; +#75546 = ADVANCED_FACE ( 'NONE', ( #9797 ), #64521, .T. ) ; +#75547 = SURFACE_STYLE_USAGE ( .BOTH. , #53947 ) ; +#75548 = STYLED_ITEM ( 'NONE', ( #14677 ), #36937 ) ; +#75549 = PRESENTATION_STYLE_ASSIGNMENT (( #84216 ) ) ; +#75550 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47468 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75504, #97459, #60225 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75552 = ORIENTED_EDGE ( 'NONE', *, *, #25103, .F. ) ; +#75551 = SURFACE_SIDE_STYLE ('',( #81737 ) ) ; +#75553 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61052, #36565, #52882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75554 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53918 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49968, #50480, #81615 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75555 = LINE ( 'NONE', #45375, #30240 ) ; +#75556 = FACE_OUTER_BOUND ( 'NONE', #24169, .T. ) ; +#75557 = ORIENTED_EDGE ( 'NONE', *, *, #85462, .T. ) ; +#75558 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8100000000000000533 ) ) ; +#75559 = FILL_AREA_STYLE_COLOUR ( '', #75424 ) ; +#75560 = EDGE_LOOP ( 'NONE', ( #26034, #88466, #11671, #54480 ) ) ; +#75561 = ORIENTED_EDGE ( 'NONE', *, *, #45875, .T. ) ; +#75562 = ADVANCED_FACE ( 'NONE', ( #87488 ), #60619, .T. ) ; +#75563 = FILL_AREA_STYLE_COLOUR ( '', #35677 ) ; +#75564 = ADVANCED_FACE ( 'NONE', ( #4722 ), #4235, .T. ) ; +#75565 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#75566 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#75567 = EDGE_CURVE ( 'NONE', #15091, #54776, #19553, .T. ) ; +#75568 = SURFACE_SIDE_STYLE ('',( #83243 ) ) ; +#75569 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75570 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.01499999999999999944, 0.1400000000000000133 ) ) ; +#75571 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#75572 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75573 = EDGE_LOOP ( 'NONE', ( #46024, #100656, #36627, #62772 ) ) ; +#75574 = CARTESIAN_POINT ( 'NONE', ( -0.9232862852897980588, -1.401385721107119897, 0.8100000000000000533 ) ) ; +#75575 = ORIENTED_EDGE ( 'NONE', *, *, #37601, .F. ) ; +#75576 = VECTOR ( 'NONE', #92245, 1000.000000000000000 ) ; +#75577 = FILL_AREA_STYLE_COLOUR ( '', #18707 ) ; +#75578 = CARTESIAN_POINT ( 'NONE', ( -0.1557459988712610044, -1.504992180692799941, 0.8299999999999999600 ) ) ; +#75580 = EDGE_CURVE ( 'NONE', #21935, #74573, #25728, .T. ) ; +#75579 = CARTESIAN_POINT ( 'NONE', ( 6.678958916749879293, 4.142827083250041120, 0.8648700000000000276 ) ) ; +#75581 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75583 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.099999999999999867, 0.000000000000000000 ) ) ; +#75582 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2808578643762690286, -0.1500000000000000222 ) ) ; +#75584 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75585 = EDGE_CURVE ( 'NONE', #74534, #57617, #49727, .T. ) ; +#75586 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75587 = CARTESIAN_POINT ( 'NONE', ( 4.389605418774279677, 1.429466554050291993, -11.91953761063119899 ) ) ; +#75588 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#75589 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95094 ), #39731 ) ; +#75590 = LINE ( 'NONE', #28624, #66252 ) ; +#75591 = EDGE_CURVE ( 'NONE', #34620, #10790, #80862, .T. ) ; +#75592 = EDGE_CURVE ( 'NONE', #87071, #87714, #65021, .T. ) ; +#75594 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8991599999999999593 ) ) ; +#75593 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59318 ), #39740 ) ; +#75595 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#75596 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#75597 = AXIS2_PLACEMENT_3D ( 'NONE', #9090, #32165, #56164 ) ; +#75598 = ORIENTED_EDGE ( 'NONE', *, *, #92676, .F. ) ; +#75599 = CARTESIAN_POINT ( 'NONE', ( -1.038348751223719946, -1.423389424083600030, 0.8299999999999999600 ) ) ; +#75600 = PLANE ( 'NONE', #55450 ) ; +#75601 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97653, 'distance_accuracy_value', 'NONE'); +#75602 = SURFACE_STYLE_FILL_AREA ( #13236 ) ; +#75603 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#75604 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#75606 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49540 ) ) ; +#75605 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15205 ) ) ; +#75607 = CARTESIAN_POINT ( 'NONE', ( 0.4314211104641285099, -1.167927078461674872, 0.8100000000000001643 ) ) ; +#75608 = CYLINDRICAL_SURFACE ( 'NONE', #96166, 0.009999999999999998473 ) ; +#75609 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#75610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62604 ), #65866 ) ; +#75611 = FILL_AREA_STYLE_COLOUR ( '', #32305 ) ; +#75612 = ADVANCED_FACE ( 'NONE', ( #3731 ), #49209, .T. ) ; +#75613 = ORIENTED_EDGE ( 'NONE', *, *, #84305, .T. ) ; +#75614 = FILL_AREA_STYLE_COLOUR ( '', #48211 ) ; +#75615 = ORIENTED_EDGE ( 'NONE', *, *, #36551, .T. ) ; +#75616 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2668, 'distance_accuracy_value', 'NONE'); +#75617 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99000, 'distance_accuracy_value', 'NONE'); +#75618 = AXIS2_PLACEMENT_3D ( 'NONE', #55777, #111, #31260 ) ; +#75619 = PLANE ( 'NONE', #11228 ) ; +#75620 = SURFACE_STYLE_USAGE ( .BOTH. , #44450 ) ; +#75621 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75622 = CARTESIAN_POINT ( 'NONE', ( -0.2413611859056800091, -1.318798174699070014, 0.8299999999999995159 ) ) ; +#75623 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26746 ), #39772 ) ; +#75624 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#75625 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.783333333333333437, 0.000000000000000000 ) ) ; +#75626 = ORIENTED_EDGE ( 'NONE', *, *, #2074, .F. ) ; +#75627 = ADVANCED_FACE ( 'NONE', ( #16250 ), #100906, .T. ) ; +#75628 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75629 = FACE_OUTER_BOUND ( 'NONE', #66763, .T. ) ; +#75630 = ORIENTED_EDGE ( 'NONE', *, *, #45209, .T. ) ; +#75631 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75632 = VECTOR ( 'NONE', #3681, 1000.000000000000000 ) ; +#75633 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75634 = ORIENTED_EDGE ( 'NONE', *, *, #66916, .T. ) ; +#75635 = ADVANCED_FACE ( 'NONE', ( #77565 ), #7029, .T. ) ; +#75636 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64429 ) ) ; +#75637 = PRESENTATION_STYLE_ASSIGNMENT (( #67946 ) ) ; +#75638 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999389, 0.1199999999999999956, -1.000000000000000000 ) ) ; +#75639 = PRESENTATION_STYLE_ASSIGNMENT (( #12784 ) ) ; +#75640 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#75641 = EDGE_CURVE ( 'NONE', #45817, #82982, #44033, .T. ) ; +#75643 = ORIENTED_EDGE ( 'NONE', *, *, #56567, .F. ) ; +#75642 = EDGE_LOOP ( 'NONE', ( #91214, #26760, #18284, #96519 ) ) ; +#75644 = SURFACE_STYLE_FILL_AREA ( #52683 ) ; +#75645 = VERTEX_POINT ( 'NONE', #15233 ) ; +#75646 = FILL_AREA_STYLE_COLOUR ( '', #55796 ) ; +#75647 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23476 ) ) ; +#75648 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#75649 = ORIENTED_EDGE ( 'NONE', *, *, #57129, .T. ) ; +#75650 = ORIENTED_EDGE ( 'NONE', *, *, #81248, .T. ) ; +#75651 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 3.676137000000000210, 0.8648700000000000276 ) ) ; +#75652 = STYLED_ITEM ( 'NONE', ( #17919 ), #88504 ) ; +#75653 = CARTESIAN_POINT ( 'NONE', ( -0.4842236312130879794, -1.167783801559209911, 0.8299999999999999600 ) ) ; +#75654 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75655 = SURFACE_STYLE_FILL_AREA ( #36869 ) ; +#75656 = ORIENTED_EDGE ( 'NONE', *, *, #20140, .F. ) ; +#75657 = ORIENTED_EDGE ( 'NONE', *, *, #41340, .F. ) ; +#75658 = VECTOR ( 'NONE', #99408, 1000.000000000000000 ) ; +#75659 = EDGE_LOOP ( 'NONE', ( #42412, #37651, #18256, #26721, #24742, #68065 ) ) ; +#75660 = EDGE_CURVE ( 'NONE', #74032, #73012, #45877, .T. ) ; +#75661 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.500000000000000000, -0.02000000000000000042 ) ) ; +#75663 = EDGE_LOOP ( 'NONE', ( #78624, #22024, #32752, #2367 ) ) ; +#75662 = FACE_OUTER_BOUND ( 'NONE', #78761, .T. ) ; +#75664 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 9.135001000000000815, 0.8648700000000000276 ) ) ; +#75665 = CARTESIAN_POINT ( 'NONE', ( 1.400599642212259965, -0.9920916311794309994, 0.8300000000000008482 ) ) ; +#75666 = VECTOR ( 'NONE', #17416, 1000.000000000000000 ) ; +#75667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75668 = FACE_OUTER_BOUND ( 'NONE', #82063, .T. ) ; +#75669 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75670 = ORIENTED_EDGE ( 'NONE', *, *, #73954, .F. ) ; +#75671 = PLANE ( 'NONE', #14574 ) ; +#75672 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99968 ), #74013 ) ; +#75673 = LINE ( 'NONE', #68504, #21563 ) ; +#75674 = ORIENTED_EDGE ( 'NONE', *, *, #44114, .F. ) ; +#75675 = EDGE_CURVE ( 'NONE', #28239, #60219, #31609, .T. ) ; +#75676 = EDGE_CURVE ( 'NONE', #54161, #865, #10045, .T. ) ; +#75677 = STYLED_ITEM ( 'NONE', ( #32735 ), #38092 ) ; +#75678 = LINE ( 'NONE', #38398, #80722 ) ; +#75679 = VECTOR ( 'NONE', #72706, 1000.000000000000114 ) ; +#75680 = PRESENTATION_STYLE_ASSIGNMENT (( #56122 ) ) ; +#75681 = ADVANCED_FACE ( 'NONE', ( #1489 ), #96383, .T. ) ; +#75682 = VECTOR ( 'NONE', #68137, 1000.000000000000000 ) ; +#75683 = PLANE ( 'NONE', #60772 ) ; +#75684 = VECTOR ( 'NONE', #89472, 1000.000000000000000 ) ; +#75685 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#75686 = CARTESIAN_POINT ( 'NONE', ( -0.9190348056960269130, -1.282982640083639270, 0.8099999999997797850 ) ) ; +#75687 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8100000000001210676 ) ) ; +#75688 = SURFACE_SIDE_STYLE ('',( #30209 ) ) ; +#75689 = ORIENTED_EDGE ( 'NONE', *, *, #21959, .T. ) ; +#75690 = STYLED_ITEM ( 'NONE', ( #34252 ), #2979 ) ; +#75691 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.000000000000000000 ) ) ; +#75692 = CARTESIAN_POINT ( 'NONE', ( 1.250776364246900085, -1.163804091156239950, 0.8300000000000022915 ) ) ; +#75693 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75695 = CARTESIAN_POINT ( 'NONE', ( 1.617712736099780280, -1.425091422160009946, 0.8100000000000000533 ) ) ; +#75694 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75696 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#75697 = ADVANCED_FACE ( 'NONE', ( #9051 ), #94379, .T. ) ; +#75698 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42922, #90382, #73572, #11183, #97980, #67879, #51113, #66898, #50617, #98466, #12200, #58289, #13209, #3628, #59297, #34793, #65919, #74072, #12715 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.101913602857916120E-05, 4.134561820478385757E-05, 6.078410685937239727E-05, 7.975871741957423226E-05, 9.809563397106970772E-05, 0.0001159246450513733422, 0.0001331015568629890958, 0.0001500848695792041706, 0.0001669813285112708859, 0.0001841742391617593822, 0.0002016734443718633132, 0.0002197766717633935327, 0.0002385148391632759771, 0.0002581511027027711758, 0.0002785647693864987638, 0.0003002811567888491093 ), + .UNSPECIFIED. ) ; +#75699 = VECTOR ( 'NONE', #82686, 1000.000000000000000 ) ; +#75700 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#75701 = EDGE_LOOP ( 'NONE', ( #26965, #28583, #88922, #58911, #4001, #32127, #26940, #73389 ) ) ; +#75702 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90357 ) ) ; +#75703 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.5000000000000000000, -11.57000000000000028 ) ) ; +#75704 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75705 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11953, #50392, #60051, #91157 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#75706 = ORIENTED_EDGE ( 'NONE', *, *, #27554, .T. ) ; +#75707 = ADVANCED_FACE ( 'NONE', ( #48471 ), #33128, .T. ) ; +#75708 = EDGE_CURVE ( 'NONE', #100104, #73074, #42798, .T. ) ; +#75709 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33315 ), #10383 ) ; +#75710 = PRESENTATION_STYLE_ASSIGNMENT (( #61430 ) ) ; +#75711 = LINE ( 'NONE', #82881, #20821 ) ; +#75712 = FACE_OUTER_BOUND ( 'NONE', #49173, .T. ) ; +#75713 = SURFACE_STYLE_FILL_AREA ( #37440 ) ; +#75714 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61020 ), #31697 ) ; +#75715 = VERTEX_POINT ( 'NONE', #36663 ) ; +#75716 = SURFACE_SIDE_STYLE ('',( #12353 ) ) ; +#75717 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75718 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75719 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54546 ) ) ; +#75720 = LINE ( 'NONE', #82898, #27351 ) ; +#75721 = PRESENTATION_STYLE_ASSIGNMENT (( #67541 ) ) ; +#75722 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75723 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50873 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21220, #91172, #67178 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75724 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75725 = FILL_AREA_STYLE_COLOUR ( '', #89945 ) ; +#75726 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52893, 'distance_accuracy_value', 'NONE'); +#75727 = EDGE_CURVE ( 'NONE', #58891, #51917, #98539, .T. ) ; +#75728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62711 ), #2432 ) ; +#75729 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, -0.1400000000000000133 ) ) ; +#75730 = ORIENTED_EDGE ( 'NONE', *, *, #98188, .T. ) ; +#75731 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8991599999999999593 ) ) ; +#75732 = VERTEX_POINT ( 'NONE', #35670 ) ; +#75733 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.383333333333323090, 1.747825839084783216E-76 ) ) ; +#75734 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11521, 'distance_accuracy_value', 'NONE'); +#75735 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46034, 'distance_accuracy_value', 'NONE'); +#75736 = SURFACE_STYLE_USAGE ( .BOTH. , #35967 ) ; +#75737 = DIRECTION ( 'NONE', ( 0.7071067811865435759, -0.7071067811865514585, 0.000000000000000000 ) ) ; +#75738 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#75739 = VECTOR ( 'NONE', #84246, 1000.000000000000000 ) ; +#75740 = SURFACE_STYLE_USAGE ( .BOTH. , #7218 ) ; +#75741 = VECTOR ( 'NONE', #54921, 1000.000000000000000 ) ; +#75742 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75743 = LINE ( 'NONE', #67077, #50064 ) ; +#75744 = SURFACE_SIDE_STYLE ('',( #20608 ) ) ; +#75745 = CIRCLE ( 'NONE', #44743, 0.04999999999999969746 ) ; +#75746 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#75747 = ORIENTED_EDGE ( 'NONE', *, *, #2544, .T. ) ; +#75748 = EDGE_CURVE ( 'NONE', #68307, #58118, #82613, .T. ) ; +#75749 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75750 = FILL_AREA_STYLE_COLOUR ( '', #24290 ) ; +#75751 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97631, 'distance_accuracy_value', 'NONE'); +#75752 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.45467499999999994, 0.8991599999999999593 ) ) ; +#75753 = SURFACE_STYLE_USAGE ( .BOTH. , #13391 ) ; +#75754 = ORIENTED_EDGE ( 'NONE', *, *, #33992, .T. ) ; +#75755 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75756 = ADVANCED_FACE ( 'NONE', ( #73452 ), #82123, .T. ) ; +#75757 = STYLED_ITEM ( 'NONE', ( #67893 ), #61308 ) ; +#75758 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75759 = VECTOR ( 'NONE', #40381, 1000.000000000000114 ) ; +#75760 = CARTESIAN_POINT ( 'NONE', ( 1.395857244856030022, -1.450479623942970253, 0.8299999999999994049 ) ) ; +#75761 = FILL_AREA_STYLE_COLOUR ( '', #12995 ) ; +#75762 = CARTESIAN_POINT ( 'NONE', ( 3.822248000000000090, 8.003631000000000384, 0.8991599999999999593 ) ) ; +#75763 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000001332, -0.1400000000000000411 ) ) ; +#75764 = ADVANCED_FACE ( 'NONE', ( #28003 ), #26160, .F. ) ; +#75765 = VERTEX_POINT ( 'NONE', #69769 ) ; +#75766 = SURFACE_SIDE_STYLE ('',( #52800 ) ) ; +#75767 = VECTOR ( 'NONE', #79065, 1000.000000000000000 ) ; +#75768 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20084, 'distance_accuracy_value', 'NONE'); +#75769 = FILL_AREA_STYLE_COLOUR ( '', #49505 ) ; +#75770 = STYLED_ITEM ( 'NONE', ( #46530 ), #12152 ) ; +#75771 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#75772 = VERTEX_POINT ( 'NONE', #53477 ) ; +#75773 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75774 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, -1.899999999999999689, -0.02000000000000000042 ) ) ; +#75775 = FILL_AREA_STYLE ('',( #13410 ) ) ; +#75776 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#75777 = ORIENTED_EDGE ( 'NONE', *, *, #31663, .F. ) ; +#75778 = EDGE_CURVE ( 'NONE', #95850, #96560, #100796, .T. ) ; +#75779 = EDGE_CURVE ( 'NONE', #97257, #56731, #30445, .T. ) ; +#75780 = VECTOR ( 'NONE', #82999, 1000.000000000000000 ) ; +#75781 = ADVANCED_FACE ( 'NONE', ( #93229 ), #77952, .T. ) ; +#75782 = ORIENTED_EDGE ( 'NONE', *, *, #81912, .T. ) ; +#75783 = ADVANCED_FACE ( 'NONE', ( #56006 ), #64156, .T. ) ; +#75785 = ORIENTED_EDGE ( 'NONE', *, *, #10782, .F. ) ; +#75784 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#75786 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#75787 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75788 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75789 = ORIENTED_EDGE ( 'NONE', *, *, #93880, .F. ) ; +#75790 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75791 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.8333333333333322601, 0.000000000000000000 ) ) ; +#75792 = ORIENTED_EDGE ( 'NONE', *, *, #61087, .T. ) ; +#75793 = LINE ( 'NONE', #37010, #20408 ) ; +#75794 = VECTOR ( 'NONE', #97596, 1000.000000000000000 ) ; +#75795 = EDGE_CURVE ( 'NONE', #36865, #98326, #48842, .T. ) ; +#75796 = SURFACE_SIDE_STYLE ('',( #13433 ) ) ; +#75797 = LINE ( 'NONE', #12930, #51574 ) ; +#75798 = VERTEX_POINT ( 'NONE', #72816 ) ; +#75800 = FILL_AREA_STYLE_COLOUR ( '', #55134 ) ; +#75799 = CARTESIAN_POINT ( 'NONE', ( 1.739573088979519788, -1.154690592117219694, 0.8099999999999998312 ) ) ; +#75801 = VECTOR ( 'NONE', #63732, 1000.000000000000000 ) ; +#75802 = VERTEX_POINT ( 'NONE', #17154 ) ; +#75803 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100176 ), #95379 ) ; +#75804 = ADVANCED_FACE ( 'NONE', ( #86616 ), #9921, .T. ) ; +#75806 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75805 = CARTESIAN_POINT ( 'NONE', ( 0.2588531918745809457, -1.291491417255038465, 0.8100000000000002753 ) ) ; +#75807 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65581 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21525, #52689, #66987 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75808 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75809 = SURFACE_STYLE_FILL_AREA ( #38516 ) ; +#75810 = PRESENTATION_STYLE_ASSIGNMENT (( #44648 ) ) ; +#75811 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75812 = ORIENTED_EDGE ( 'NONE', *, *, #766, .F. ) ; +#75813 = ORIENTED_EDGE ( 'NONE', *, *, #79761, .F. ) ; +#75814 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#75815 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62801 ), #13801 ) ; +#75817 = SURFACE_SIDE_STYLE ('',( #6304 ) ) ; +#75816 = PRESENTATION_STYLE_ASSIGNMENT (( #44653 ) ) ; +#75818 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75819 = LINE ( 'NONE', #82001, #72617 ) ; +#75820 = AXIS2_PLACEMENT_3D ( 'NONE', #89504, #59397, #11292 ) ; +#75821 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25287 ), #28528 ) ; +#75822 = SURFACE_SIDE_STYLE ('',( #98228 ) ) ; +#75823 = SURFACE_STYLE_FILL_AREA ( #60042 ) ; +#75824 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, 0.000000000000000000 ) ) ; +#75825 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75826 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75827 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#75828 = LINE ( 'NONE', #46151, #48764 ) ; +#75829 = ORIENTED_EDGE ( 'NONE', *, *, #10642, .T. ) ; +#75830 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#75831 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 0.6999999999999999556, -13.54999999999999893 ) ) ; +#75832 = EDGE_CURVE ( 'NONE', #7486, #31439, #43655, .T. ) ; +#75834 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#75833 = FILL_AREA_STYLE ('',( #16035 ) ) ; +#75835 = DIRECTION ( 'NONE', ( 0.000000000000000000, -3.252606517456505019E-15, -1.000000000000000000 ) ) ; +#75836 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999996739, -1.979898987322330051, 0.5799137866959191978 ) ) ; +#75837 = SURFACE_STYLE_USAGE ( .BOTH. , #13469 ) ; +#75838 = ADVANCED_FACE ( 'NONE', ( #19692, #42190 ), #80999, .F. ) ; +#75839 = PRESENTATION_STYLE_ASSIGNMENT (( #13472 ) ) ; +#75840 = ORIENTED_EDGE ( 'NONE', *, *, #67832, .T. ) ; +#75841 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75842 = CARTESIAN_POINT ( 'NONE', ( -0.007147714975284390031, -1.399205570841099977, 0.8299999999999999600 ) ) ; +#75843 = SURFACE_STYLE_USAGE ( .BOTH. , #44679 ) ; +#75844 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#75845 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#75846 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#75847 = FACE_OUTER_BOUND ( 'NONE', #92246, .T. ) ; +#75848 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#75849 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.49753199999999964, 0.8648700000000000276 ) ) ; +#75850 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 2.877107000000000525, 0.8991599999999999593 ) ) ; +#75851 = FILL_AREA_STYLE ('',( #13494 ) ) ; +#75852 = VECTOR ( 'NONE', #78999, 1000.000000000000000 ) ; +#75854 = ADVANCED_FACE ( 'NONE', ( #65648 ), #10942, .F. ) ; +#75853 = VECTOR ( 'NONE', #50591, 1000.000000000000000 ) ; +#75855 = LINE ( 'NONE', #31403, #94288 ) ; +#75856 = FACE_OUTER_BOUND ( 'NONE', #97060, .T. ) ; +#75857 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999995115, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#75858 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#75859 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43373, 'distance_accuracy_value', 'NONE'); +#75860 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75861 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69249 ), #33476 ) ; +#75862 = SURFACE_SIDE_STYLE ('',( #44697 ) ) ; +#75863 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75864 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#75865 = SURFACE_SIDE_STYLE ('',( #76876 ) ) ; +#75866 = ORIENTED_EDGE ( 'NONE', *, *, #60663, .T. ) ; +#75867 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75869 = EDGE_CURVE ( 'NONE', #45393, #27603, #67628, .T. ) ; +#75868 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28765 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5901, #22787, #77394 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75870 = PRESENTATION_STYLE_ASSIGNMENT (( #51411 ) ) ; +#75871 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35476, 'distance_accuracy_value', 'NONE'); +#75872 = VECTOR ( 'NONE', #31081, 1000.000000000000000 ) ; +#75873 = LINE ( 'NONE', #90699, #99106 ) ; +#75874 = STYLED_ITEM ( 'NONE', ( #61598 ), #48563 ) ; +#75875 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#75876 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27378 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59354, #5138, #91448 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75877 = PRESENTATION_STYLE_ASSIGNMENT (( #45202 ) ) ; +#75878 = CARTESIAN_POINT ( 'NONE', ( 0.4664346272664121607, -1.039067854021756165, 0.8100000000000001643 ) ) ; +#75879 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49821 ) ) ; +#75880 = EDGE_CURVE ( 'NONE', #2215, #14770, #73821, .T. ) ; +#75881 = ORIENTED_EDGE ( 'NONE', *, *, #414, .F. ) ; +#75882 = SURFACE_STYLE_FILL_AREA ( #69179 ) ; +#75883 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52362, 'distance_accuracy_value', 'NONE'); +#75884 = ADVANCED_FACE ( 'NONE', ( #4850 ), #58540, .T. ) ; +#75885 = FILL_AREA_STYLE_COLOUR ( '', #63315 ) ; +#75886 = EDGE_LOOP ( 'NONE', ( #36469, #38827, #47813, #86151 ) ) ; +#75887 = ORIENTED_EDGE ( 'NONE', *, *, #57918, .T. ) ; +#75889 = VECTOR ( 'NONE', #82746, 1000.000000000000000 ) ; +#75888 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77488 ) ) ; +#75890 = VECTOR ( 'NONE', #11351, 1000.000000000000000 ) ; +#75891 = SURFACE_STYLE_USAGE ( .BOTH. , #21764 ) ; +#75893 = LINE ( 'NONE', #99758, #72023 ) ; +#75892 = CARTESIAN_POINT ( 'NONE', ( 0.4178376006486049787, -0.9790859034276460093, 0.8300000000000002931 ) ) ; +#75894 = ORIENTED_EDGE ( 'NONE', *, *, #65169, .T. ) ; +#75895 = CARTESIAN_POINT ( 'NONE', ( 0.5335638015470970386, -1.143334495870530265, 0.8100000000000000533 ) ) ; +#75896 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#75897 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#75898 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#75899 = ADVANCED_FACE ( 'NONE', ( #37030 ), #52847, .T. ) ; +#75900 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63821 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70954, #74488, #4508 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#75901 = ADVANCED_FACE ( 'NONE', ( #23213 ), #68638, .T. ) ; +#75902 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #60703, #32849 ) ; +#75903 = SURFACE_STYLE_USAGE ( .BOTH. , #27448 ) ; +#75904 = EDGE_LOOP ( 'NONE', ( #10667, #100563, #63105, #30398 ) ) ; +#75905 = EDGE_CURVE ( 'NONE', #97279, #3083, #33114, .T. ) ; +#75906 = ORIENTED_EDGE ( 'NONE', *, *, #4075, .T. ) ; +#75907 = EDGE_CURVE ( 'NONE', #406, #99386, #6780, .T. ) ; +#75908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75909 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93790 ) ) ; +#75910 = PRESENTATION_STYLE_ASSIGNMENT (( #27973 ) ) ; +#75912 = SURFACE_STYLE_FILL_AREA ( #98318 ) ; +#75911 = CARTESIAN_POINT ( 'NONE', ( 0.4491032436848350073, -0.9174134460922771517, 0.8299999999999999600 ) ) ; +#75913 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75914 = SURFACE_SIDE_STYLE ('',( #14588 ) ) ; +#75915 = PLANE ( 'NONE', #37625 ) ; +#75916 = ADVANCED_FACE ( 'NONE', ( #30848 ), #62032, .T. ) ; +#75917 = CARTESIAN_POINT ( 'NONE', ( -1.254664462595540098, -0.9005718509792439708, 0.8100000000000000533 ) ) ; +#75918 = ORIENTED_EDGE ( 'NONE', *, *, #12044, .T. ) ; +#75919 = VECTOR ( 'NONE', #69366, 1000.000000000000114 ) ; +#75920 = VERTEX_POINT ( 'NONE', #1217 ) ; +#75921 = ORIENTED_EDGE ( 'NONE', *, *, #92143, .T. ) ; +#75922 = CARTESIAN_POINT ( 'NONE', ( 1.028534346447049996, -1.164020980542209927, 0.8100000000000000533 ) ) ; +#75923 = EDGE_CURVE ( 'NONE', #99386, #49941, #31356, .T. ) ; +#75925 = LINE ( 'NONE', #99322, #20512 ) ; +#75924 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#75926 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12224 ), #41695 ) ; +#75927 = ORIENTED_EDGE ( 'NONE', *, *, #54602, .F. ) ; +#75928 = SURFACE_STYLE_USAGE ( .BOTH. , #27481 ) ; +#75929 = SURFACE_STYLE_FILL_AREA ( #14603 ) ; +#75930 = PLANE ( 'NONE', #87409 ) ; +#75931 = VECTOR ( 'NONE', #53473, 1000.000000000000000 ) ; +#75932 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43353 ), #98732 ) ; +#75933 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 1.458578643762689975, 0.000000000000000000 ) ) ; +#75934 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44918 ) ) ; +#75935 = EDGE_LOOP ( 'NONE', ( #70347, #62520, #64498, #33599 ) ) ; +#75937 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75936 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75938 = SURFACE_STYLE_USAGE ( .BOTH. , #89748 ) ; +#75939 = EDGE_LOOP ( 'NONE', ( #87053, #1306, #75227, #5340, #52967, #77418, #59035, #85819 ) ) ; +#75940 = EDGE_LOOP ( 'NONE', ( #2642, #77145, #11766, #6730 ) ) ; +#75941 = CARTESIAN_POINT ( 'NONE', ( 0.9776395701974860408, -1.395425853902759972, 0.8299999999999999600 ) ) ; +#75942 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75943 = LINE ( 'NONE', #37163, #67806 ) ; +#75944 = FACE_OUTER_BOUND ( 'NONE', #11780, .T. ) ; +#75945 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48197 ), #82449 ) ; +#75946 = VECTOR ( 'NONE', #50152, 1000.000000000000000 ) ; +#75947 = PLANE ( 'NONE', #1007 ) ; +#75948 = PRODUCT ( 'Imported', 'Imported', '', ( #6987 ) ) ; +#75949 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75950 = ORIENTED_EDGE ( 'NONE', *, *, #55710, .T. ) ; +#75951 = VECTOR ( 'NONE', #58129, 1000.000000000000000 ) ; +#75952 = ORIENTED_EDGE ( 'NONE', *, *, #23868, .F. ) ; +#75953 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20555 ) ) ; +#75954 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75955 = CARTESIAN_POINT ( 'NONE', ( -0.06269022549541880540, -0.9718760589866800581, 0.8100000000000000533 ) ) ; +#75956 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#75957 = STYLED_ITEM ( 'NONE', ( #56702 ), #15729 ) ; +#75958 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#75959 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8199999999999999512 ) ) ; +#75960 = AXIS2_PLACEMENT_3D ( 'NONE', #7719, #23648, #71110 ) ; +#75961 = FACE_OUTER_BOUND ( 'NONE', #98828, .T. ) ; +#75962 = EDGE_CURVE ( 'NONE', #89867, #46291, #87012, .T. ) ; +#75963 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#75964 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75965 = VERTEX_POINT ( 'NONE', #95127 ) ; +#75966 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#75967 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#75968 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.000000000000000000 ) ) ; +#75969 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12334 ) ) ; +#75970 = FACE_BOUND ( 'NONE', #75497, .T. ) ; +#75971 = DIRECTION ( 'NONE', ( -4.640777529015779698E-48, -0.000000000000000000, 1.000000000000000000 ) ) ; +#75972 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#75973 = VECTOR ( 'NONE', #1620, 1000.000000000000000 ) ; +#75974 = FACE_OUTER_BOUND ( 'NONE', #97642, .T. ) ; +#75975 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#75976 = VECTOR ( 'NONE', #45857, 1000.000000000000000 ) ; +#75977 = LINE ( 'NONE', #15671, #57120 ) ; +#75978 = SURFACE_SIDE_STYLE ('',( #37199 ) ) ; +#75979 = PRESENTATION_STYLE_ASSIGNMENT (( #98867 ) ) ; +#75980 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#75981 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12350 ) ) ; +#75982 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20882, 'distance_accuracy_value', 'NONE'); +#75983 = EDGE_LOOP ( 'NONE', ( #71952, #39439, #51321, #89034 ) ) ; +#75984 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.449999999999999956, -11.82000000000000028 ) ) ; +#75985 = FACE_OUTER_BOUND ( 'NONE', #92432, .T. ) ; +#75986 = ORIENTED_EDGE ( 'NONE', *, *, #16314, .F. ) ; +#75987 = SURFACE_SIDE_STYLE ('',( #29026 ) ) ; +#75988 = ADVANCED_FACE ( 'NONE', ( #8295 ), #39525, .T. ) ; +#75989 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#75990 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#75991 = SURFACE_STYLE_FILL_AREA ( #59727 ) ; +#75992 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20952, 'distance_accuracy_value', 'NONE'); +#75993 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#75994 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#75995 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61389 ), #31984 ) ; +#75996 = ORIENTED_EDGE ( 'NONE', *, *, #3746, .F. ) ; +#75997 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#75998 = LINE ( 'NONE', #93166, #17271 ) ; +#75999 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#76000 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50458, 'distance_accuracy_value', 'NONE'); +#76002 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76001 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70867 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51394, #82529, #50413 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76003 = VECTOR ( 'NONE', #10830, 1000.000000000000114 ) ; +#76004 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76005 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71896, 'distance_accuracy_value', 'NONE'); +#76006 = ADVANCED_FACE ( 'NONE', ( #32386 ), #80365, .T. ) ; +#76007 = STYLED_ITEM ( 'NONE', ( #62492 ), #49672 ) ; +#76008 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7998 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5205, #76695, #90516 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76009 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8100000000000601164 ) ) ; +#76010 = ORIENTED_EDGE ( 'NONE', *, *, #70303, .T. ) ; +#76012 = EDGE_LOOP ( 'NONE', ( #80187, #69101, #91271, #66566 ) ) ; +#76011 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18942 ) ) ; +#76013 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46845, 'distance_accuracy_value', 'NONE'); +#76014 = VERTEX_POINT ( 'NONE', #42559 ) ; +#76015 = CARTESIAN_POINT ( 'NONE', ( -0.3116078311044310212, -1.336216925617480067, 0.8299999999999999600 ) ) ; +#76016 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54833 ) ) ; +#76017 = FACE_OUTER_BOUND ( 'NONE', #77671, .T. ) ; +#76018 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000089, 2.676179938779915002, -0.02000000000000000042 ) ) ; +#76019 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76020 = PLANE ( 'NONE', #88762 ) ; +#76021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76022 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76023 = LINE ( 'NONE', #46360, #98060 ) ; +#76024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98161 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63136, #16109, #79457 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76025 = CARTESIAN_POINT ( 'NONE', ( -1.282481293671730027, -1.007957212727089935, 0.8299999999999999600 ) ) ; +#76027 = ORIENTED_EDGE ( 'NONE', *, *, #61984, .F. ) ; +#76026 = ORIENTED_EDGE ( 'NONE', *, *, #60391, .F. ) ; +#76028 = VECTOR ( 'NONE', #44295, 1000.000000000000000 ) ; +#76029 = EDGE_LOOP ( 'NONE', ( #97802, #46880, #95320, #78077 ) ) ; +#76030 = EDGE_CURVE ( 'NONE', #61768, #56612, #67031, .T. ) ; +#76031 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#76032 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#76033 = VERTEX_POINT ( 'NONE', #26748 ) ; +#76034 = ORIENTED_EDGE ( 'NONE', *, *, #75591, .F. ) ; +#76036 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76035 = SURFACE_SIDE_STYLE ('',( #66377 ) ) ; +#76037 = CARTESIAN_POINT ( 'NONE', ( 6.678959124874999986, 8.385468875124999499, 0.8991599999999999593 ) ) ; +#76038 = AXIS2_PLACEMENT_3D ( 'NONE', #48780, #79921, #62085 ) ; +#76039 = FILL_AREA_STYLE_COLOUR ( '', #51970 ) ; +#76041 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#76040 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2000000000000000111, -13.54999999999999893 ) ) ; +#76042 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4808578643762690952, -0.2500000000000000000 ) ) ; +#76043 = EDGE_LOOP ( 'NONE', ( #48051, #67753, #22623, #80285 ) ) ; +#76044 = ORIENTED_EDGE ( 'NONE', *, *, #20871, .T. ) ; +#76045 = ORIENTED_EDGE ( 'NONE', *, *, #5579, .F. ) ; +#76046 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8648700000000000276 ) ) ; +#76047 = EDGE_CURVE ( 'NONE', #34164, #69166, #33912, .T. ) ; +#76048 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76051 = ORIENTED_EDGE ( 'NONE', *, *, #42042, .T. ) ; +#76050 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47683, 'distance_accuracy_value', 'NONE'); +#76049 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#76052 = AXIS2_PLACEMENT_3D ( 'NONE', #90604, #57999, #20644 ) ; +#76053 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76054 = VERTEX_POINT ( 'NONE', #34417 ) ; +#76055 = LINE ( 'NONE', #45378, #77793 ) ; +#76056 = ORIENTED_EDGE ( 'NONE', *, *, #48473, .T. ) ; +#76057 = ORIENTED_EDGE ( 'NONE', *, *, #84348, .T. ) ; +#76058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76059 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76060 = PLANE ( 'NONE', #90585 ) ; +#76061 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44216 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2132, #32265, #1630 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76062 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000000311, 0.1399999999999991807 ) ) ; +#76063 = PRESENTATION_STYLE_ASSIGNMENT (( #52609 ) ) ; +#76064 = CARTESIAN_POINT ( 'NONE', ( 1.108771792731459982, -1.202560495203230051, 0.8299999999999997380 ) ) ; +#76065 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76066 = CARTESIAN_POINT ( 'NONE', ( 0.3385502766025340060, -0.9005362424757039630, 0.8300000000000020695 ) ) ; +#76067 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76068 = ORIENTED_EDGE ( 'NONE', *, *, #24412, .T. ) ; +#76069 = SURFACE_STYLE_FILL_AREA ( #7538 ) ; +#76070 = PRESENTATION_STYLE_ASSIGNMENT (( #6061 ) ) ; +#76071 = ORIENTED_EDGE ( 'NONE', *, *, #31232, .T. ) ; +#76072 = PLANE ( 'NONE', #62771 ) ; +#76073 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76074 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25939 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61568, #7827, #76857 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76075 = STYLED_ITEM ( 'NONE', ( #17812 ), #90704 ) ; +#76076 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76078 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#76077 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76080 = CARTESIAN_POINT ( 'NONE', ( 1.773496746821729975, -1.132325613921520091, 0.8100000000000000533 ) ) ; +#76081 = EDGE_CURVE ( 'NONE', #40643, #60367, #97144, .T. ) ; +#76082 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76083 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.566666666666666652, 0.000000000000000000 ) ) ; +#76084 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76085 = CARTESIAN_POINT ( 'NONE', ( -1.284259234833809993, -1.485874691073119980, 0.8300000000000024025 ) ) ; +#76086 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76087 = CARTESIAN_POINT ( 'NONE', ( 4.400663157199260489, 1.440488883097521988, -11.91784188231304142 ) ) ; +#76088 = LINE ( 'NONE', #7054, #10393 ) ; +#76089 = SURFACE_STYLE_FILL_AREA ( #67899 ) ; +#76090 = VECTOR ( 'NONE', #79346, 1000.000000000000000 ) ; +#76091 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76092 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #54697, #79171, #55210, #9134 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76093 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46704 ) ) ; +#76094 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#76095 = PRESENTATION_STYLE_ASSIGNMENT (( #98978 ) ) ; +#76096 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76097 = VECTOR ( 'NONE', #62679, 1000.000000000000000 ) ; +#76098 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#76099 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80798 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97419, #67302, #27533 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76100 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76101 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3893, 'distance_accuracy_value', 'NONE'); +#76102 = VERTEX_POINT ( 'NONE', #26243 ) ; +#76103 = SURFACE_STYLE_USAGE ( .BOTH. , #43452 ) ; +#76104 = EDGE_CURVE ( 'NONE', #7500, #60542, #73692, .T. ) ; +#76106 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23635 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17301, #42819, #28020 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76105 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#76107 = STYLED_ITEM ( 'NONE', ( #2181 ), #100160 ) ; +#76108 = PRESENTATION_STYLE_ASSIGNMENT (( #13758 ) ) ; +#76109 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76110 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#76111 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#76112 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76113 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76114 = EDGE_CURVE ( 'NONE', #25673, #76160, #98102, .T. ) ; +#76115 = VECTOR ( 'NONE', #57080, 1000.000000000000000 ) ; +#76116 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#76117 = ORIENTED_EDGE ( 'NONE', *, *, #90049, .F. ) ; +#76118 = SURFACE_SIDE_STYLE ('',( #21987 ) ) ; +#76119 = ORIENTED_EDGE ( 'NONE', *, *, #68037, .T. ) ; +#76120 = SURFACE_STYLE_FILL_AREA ( #44944 ) ; +#76121 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 9.949999999999999289, 0.000000000000000000 ) ) ; +#76122 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76123 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#76124 = VECTOR ( 'NONE', #13812, 1000.000000000000000 ) ; +#76125 = FILL_AREA_STYLE ('',( #36833 ) ) ; +#76126 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666639518, -1.300000000000000266, 0.000000000000000000 ) ) ; +#76127 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#76128 = ORIENTED_EDGE ( 'NONE', *, *, #58670, .T. ) ; +#76129 = EDGE_CURVE ( 'NONE', #67492, #68437, #57919, .T. ) ; +#76130 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76131 = EDGE_CURVE ( 'NONE', #61829, #6634, #81879, .T. ) ; +#76132 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76133 = ORIENTED_EDGE ( 'NONE', *, *, #47008, .F. ) ; +#76134 = LINE ( 'NONE', #6124, #6586 ) ; +#76135 = EDGE_LOOP ( 'NONE', ( #84329, #78832, #26529, #67910 ) ) ; +#76136 = AXIS2_PLACEMENT_3D ( 'NONE', #38171, #30460, #68770 ) ; +#76137 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.7099999999999999645, -9.196726089365473794E-18 ) ) ; +#76138 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1400000000000000411 ) ) ; +#76139 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76140 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76141 = SURFACE_STYLE_FILL_AREA ( #91465 ) ; +#76142 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76144 = ORIENTED_EDGE ( 'NONE', *, *, #26333, .F. ) ; +#76143 = EDGE_LOOP ( 'NONE', ( #34263, #39254, #22829, #5523 ) ) ; +#76145 = DIRECTION ( 'NONE', ( -0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#76146 = ORIENTED_EDGE ( 'NONE', *, *, #80273, .F. ) ; +#76147 = ADVANCED_FACE ( 'NONE', ( #35431 ), #58003, .F. ) ; +#76148 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#76149 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48419 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5616, #45422, #81426 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76150 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58271 ) ) ; +#76152 = CARTESIAN_POINT ( 'NONE', ( -0.5167674196284709476, -0.9767818844061101347, 0.8100000000000000533 ) ) ; +#76151 = SURFACE_STYLE_FILL_AREA ( #44480 ) ; +#76153 = ORIENTED_EDGE ( 'NONE', *, *, #2964, .T. ) ; +#76154 = VERTEX_POINT ( 'NONE', #83865 ) ; +#76155 = FILL_AREA_STYLE_COLOUR ( '', #53047 ) ; +#76156 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#76157 = VECTOR ( 'NONE', #76192, 1000.000000000000000 ) ; +#76158 = SURFACE_STYLE_USAGE ( .BOTH. , #44984 ) ; +#76159 = ORIENTED_EDGE ( 'NONE', *, *, #8244, .F. ) ; +#76160 = VERTEX_POINT ( 'NONE', #53234 ) ; +#76161 = EDGE_LOOP ( 'NONE', ( #86322, #52424, #91564, #61051 ) ) ; +#76162 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.699999999999999734, 0.1829999999999459837 ) ) ; +#76163 = EDGE_CURVE ( 'NONE', #84768, #80553, #61413, .T. ) ; +#76164 = AXIS2_PLACEMENT_3D ( 'NONE', #37979, #32213, #63381 ) ; +#76165 = AXIS2_PLACEMENT_3D ( 'NONE', #81287, #96542, #72574 ) ; +#76167 = VERTEX_POINT ( 'NONE', #68520 ) ; +#76166 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.183333333333333570, 0.000000000000000000 ) ) ; +#76168 = AXIS2_PLACEMENT_3D ( 'NONE', #19205, #75355, #5366 ) ; +#76169 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59965 ) ) ; +#76170 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#76171 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8991599999999999593 ) ) ; +#76172 = SURFACE_SIDE_STYLE ('',( #61396 ) ) ; +#76173 = ORIENTED_EDGE ( 'NONE', *, *, #72342, .F. ) ; +#76174 = SURFACE_STYLE_FILL_AREA ( #99065 ) ; +#76175 = CLOSED_SHELL ( 'NONE', ( #7377, #12615, #45101, #24366, #90751, #99573 ) ) ; +#76176 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#76177 = ORIENTED_EDGE ( 'NONE', *, *, #70534, .T. ) ; +#76178 = VECTOR ( 'NONE', #66172, 1000.000000000000000 ) ; +#76179 = FILL_AREA_STYLE_COLOUR ( '', #48096 ) ; +#76180 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74602 ) ) ; +#76181 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76182 = VERTEX_POINT ( 'NONE', #92496 ) ; +#76184 = LINE ( 'NONE', #61894, #6581 ) ; +#76183 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76185 = LINE ( 'NONE', #23583, #12767 ) ; +#76187 = CARTESIAN_POINT ( 'NONE', ( 1.508691354424569919, -1.396584910994119966, 0.8100000000000000533 ) ) ; +#76186 = FACE_OUTER_BOUND ( 'NONE', #29357, .T. ) ; +#76188 = EDGE_CURVE ( 'NONE', #86759, #9645, #85357, .T. ) ; +#76189 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610389962, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#76190 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76191 = ORIENTED_EDGE ( 'NONE', *, *, #80782, .F. ) ; +#76192 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76193 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.123820061220085265, -0.02000000000000000042 ) ) ; +#76194 = LINE ( 'NONE', #52727, #95761 ) ; +#76196 = CARTESIAN_POINT ( 'NONE', ( 1.290154168107711774, -1.436993929120639057, 0.8099999999997149480 ) ) ; +#76195 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#76197 = LINE ( 'NONE', #99089, #68114 ) ; +#76198 = EDGE_CURVE ( 'NONE', #15626, #21395, #46013, .T. ) ; +#76199 = EDGE_CURVE ( 'NONE', #73074, #93922, #24137, .T. ) ; +#76200 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7603 ), #89271 ) ; +#76201 = EDGE_LOOP ( 'NONE', ( #56979, #76545, #42425, #43504 ) ) ; +#76202 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76203 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -1.500000000000000000, 1.747825839084689943E-76 ) ) ; +#76204 = ORIENTED_EDGE ( 'NONE', *, *, #29620, .T. ) ; +#76205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76206 = ADVANCED_FACE ( 'NONE', ( #69007 ), #36409, .T. ) ; +#76208 = SURFACE_SIDE_STYLE ('',( #13871 ) ) ; +#76207 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#76209 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#76210 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50441 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80914, #83278, #90933 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76211 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76212 = SURFACE_STYLE_USAGE ( .BOTH. , #45044 ) ; +#76213 = ORIENTED_EDGE ( 'NONE', *, *, #44598, .F. ) ; +#76214 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76215 = VECTOR ( 'NONE', #23130, 1000.000000000000000 ) ; +#76216 = SURFACE_SIDE_STYLE ('',( #76720 ) ) ; +#76217 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#76218 = FILL_AREA_STYLE_COLOUR ( '', #82859 ) ; +#76219 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.4333333333333323489, 0.000000000000000000 ) ) ; +#76220 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76221 = FILL_AREA_STYLE ('',( #20592 ) ) ; +#76222 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76223 = EDGE_CURVE ( 'NONE', #81497, #3032, #5705, .T. ) ; +#76224 = FILL_AREA_STYLE_COLOUR ( '', #60669 ) ; +#76225 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69835 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44749, #47800, #57006 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76226 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76227 = VECTOR ( 'NONE', #21102, 1000.000000000000000 ) ; +#76228 = AXIS2_PLACEMENT_3D ( 'NONE', #3027, #33685, #11599 ) ; +#76229 = ORIENTED_EDGE ( 'NONE', *, *, #39735, .F. ) ; +#76230 = ORIENTED_EDGE ( 'NONE', *, *, #70466, .T. ) ; +#76231 = LINE ( 'NONE', #6230, #70769 ) ; +#76233 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61620 ) ) ; +#76232 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76234 = CARTESIAN_POINT ( 'NONE', ( -1.005612341081159933, -1.485054850390570058, 0.8299999999999981837 ) ) ; +#76235 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76236 = SURFACE_STYLE_USAGE ( .BOTH. , #21621 ) ; +#76237 = AXIS2_PLACEMENT_3D ( 'NONE', #29055, #60228, #51569 ) ; +#76238 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76239 = PLANE ( 'NONE', #100843 ) ; +#76240 = CARTESIAN_POINT ( 'NONE', ( 0.4156490935876188675, -0.9013060303225225445, 0.8099999999999999423 ) ) ; +#76241 = CLOSED_SHELL ( 'NONE', ( #92075, #20123, #84744, #91824, #64467, #38222 ) ) ; +#76242 = EDGE_LOOP ( 'NONE', ( #59793, #74553, #18816, #41362 ) ) ; +#76243 = EDGE_CURVE ( 'NONE', #15739, #98788, #56785, .T. ) ; +#76244 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76245 = EDGE_CURVE ( 'NONE', #60060, #96833, #33278, .T. ) ; +#76246 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.008431457505076211598, 0.2458578643762690530 ) ) ; +#76247 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#76248 = ORIENTED_EDGE ( 'NONE', *, *, #33489, .T. ) ; +#76249 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76250 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#76251 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19181 ) ) ; +#76252 = CARTESIAN_POINT ( 'NONE', ( 1.420458916718859932, -1.419416888468929994, 0.8299999999999994049 ) ) ; +#76253 = PRESENTATION_STYLE_ASSIGNMENT (( #36477 ) ) ; +#76254 = SURFACE_STYLE_USAGE ( .BOTH. , #13920 ) ; +#76255 = PLANE ( 'NONE', #44612 ) ; +#76256 = ORIENTED_EDGE ( 'NONE', *, *, #47307, .F. ) ; +#76257 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#76259 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76258 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76260 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76261 = EDGE_CURVE ( 'NONE', #86461, #82814, #71057, .T. ) ; +#76262 = FILL_AREA_STYLE_COLOUR ( '', #96420 ) ; +#76263 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#76264 = EDGE_LOOP ( 'NONE', ( #11518, #75630, #35010, #3984 ) ) ; +#76265 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 5.910594999999999821, 0.8991599999999999593 ) ) ; +#76266 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76267 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76268 = SURFACE_STYLE_USAGE ( .BOTH. , #14947 ) ; +#76269 = ORIENTED_EDGE ( 'NONE', *, *, #93138, .T. ) ; +#76270 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76271 = EDGE_CURVE ( 'NONE', #56700, #2575, #8174, .T. ) ; +#76272 = AXIS2_PLACEMENT_3D ( 'NONE', #55409, #86525, #71195 ) ; +#76273 = EDGE_CURVE ( 'NONE', #41904, #68541, #40949, .T. ) ; +#76274 = ORIENTED_EDGE ( 'NONE', *, *, #19487, .T. ) ; +#76276 = ORIENTED_EDGE ( 'NONE', *, *, #45277, .T. ) ; +#76275 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#76277 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19211 ) ) ; +#76278 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18262, 'distance_accuracy_value', 'NONE'); +#76279 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.699999999999999734, 9.720630125846873012E-79 ) ) ; +#76281 = CARTESIAN_POINT ( 'NONE', ( -1.375607183049269988, -1.395425853902759972, 0.8299999999999999600 ) ) ; +#76280 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76282 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76283 = EDGE_LOOP ( 'NONE', ( #28108, #61434, #5072, #83956 ) ) ; +#76284 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76285 = ORIENTED_EDGE ( 'NONE', *, *, #50970, .F. ) ; +#76286 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76287 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999749605 ) ) ; +#76288 = PLANE ( 'NONE', #89146 ) ; +#76289 = ORIENTED_EDGE ( 'NONE', *, *, #93708, .T. ) ; +#76290 = VECTOR ( 'NONE', #75696, 1000.000000000000000 ) ; +#76292 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76291 = CARTESIAN_POINT ( 'NONE', ( 1.757815472291410108, -1.145059460293619713, 0.8099999999999998312 ) ) ; +#76293 = ORIENTED_EDGE ( 'NONE', *, *, #28305, .T. ) ; +#76294 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81233 ), #35602 ) ; +#76295 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76296 = EDGE_CURVE ( 'NONE', #15529, #34205, #23592, .T. ) ; +#76297 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19230 ), #20851 ) ; +#76298 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76299 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17624 ) ) ; +#76300 = ORIENTED_EDGE ( 'NONE', *, *, #49055, .F. ) ; +#76301 = FILL_AREA_STYLE ('',( #16015 ) ) ; +#76302 = ORIENTED_EDGE ( 'NONE', *, *, #97498, .T. ) ; +#76303 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76304 = CLOSED_SHELL ( 'NONE', ( #53217, #30643, #12593, #96639, #42433, #89760 ) ) ; +#76306 = FILL_AREA_STYLE ('',( #100185 ) ) ; +#76305 = FILL_AREA_STYLE_COLOUR ( '', #83702 ) ; +#76307 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#76308 = EDGE_CURVE ( 'NONE', #17500, #2820, #95515, .T. ) ; +#76309 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#76310 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49483, #88280, #10063 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76312 = ADVANCED_FACE ( 'NONE', ( #70035 ), #55757, .F. ) ; +#76311 = LINE ( 'NONE', #61538, #65351 ) ; +#76313 = CARTESIAN_POINT ( 'NONE', ( 11.33879312487501245, 5.832812875124988139, 0.8991599999999999593 ) ) ; +#76314 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.123820061220055511, 0.000000000000000000 ) ) ; +#76315 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76316 = FILL_AREA_STYLE_COLOUR ( '', #90264 ) ; +#76317 = ORIENTED_EDGE ( 'NONE', *, *, #94957, .F. ) ; +#76318 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, -1.100000000000000089 ) ) ; +#76319 = VECTOR ( 'NONE', #47818, 1000.000000000000000 ) ; +#76320 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76321 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76322 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23528, 'distance_accuracy_value', 'NONE'); +#76323 = AXIS2_PLACEMENT_3D ( 'NONE', #70585, #86934, #38950 ) ; +#76324 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974019543, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#76325 = SURFACE_STYLE_FILL_AREA ( #97767 ) ; +#76326 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#76327 = AXIS2_PLACEMENT_3D ( 'NONE', #76800, #6766, #44634 ) ; +#76328 = ORIENTED_EDGE ( 'NONE', *, *, #18126, .F. ) ; +#76329 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#76330 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76331 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76332 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#76333 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -1.900000000000000133, 0.000000000000000000 ) ) ; +#76334 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76335 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #53145, .NOT_KNOWN. ) ; +#76336 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76337 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76338 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65135 ), #71477 ) ; +#76339 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#76340 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76341 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#76343 = EDGE_CURVE ( 'NONE', #83060, #76650, #62581, .T. ) ; +#76342 = SURFACE_STYLE_FILL_AREA ( #84023 ) ; +#76344 = ADVANCED_FACE ( 'NONE', ( #40440 ), #15526, .T. ) ; +#76345 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #25738, #88511, #65511, #96642, #29237, #81877, #82860, #27759, #98580, #21083, #12327, #60416, #51735, #75211, #28243, #75692, #51229, #35429, #20056, #82371, #5201, #36901, #4247, #89528, #83370, #97141, #58915, #12835, #27254, #19564, #28721 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.327616387800017416E-05, 2.547497420769070134E-05, 3.726786310495536615E-05, 4.895517568277734142E-05, 6.099142129637324120E-05, 7.350372333759120367E-05, 8.683811020379866678E-05, 0.0001009728839031022359, 0.0001158868716872077885, 0.0001315611172521862686, 0.0001478298764740367780, 0.0001648923924171355221, 0.0002001775098873236384, 0.0002361870138312961416, 0.0002724555859667435035, 0.0003085720862381374665, 0.0003263295848192647236, 0.0003436214609547928451, 0.0003605877124752303927, 0.0003772653758933002649, 0.0003937700570430625402, 0.0004100899809948962472, 0.0004263483064349247488, 0.0004429971904296220366, 0.0004601179808995206383, 0.0004783389212597158389, 0.0004980104121460688033, 0.0005192903765009651128 ), + .UNSPECIFIED. ) ; +#76346 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76347 = STYLED_ITEM ( 'NONE', ( #15797 ), #31398 ) ; +#76348 = SURFACE_STYLE_FILL_AREA ( #45180 ) ; +#76349 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#76350 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76351 = VECTOR ( 'NONE', #44983, 1000.000000000000000 ) ; +#76352 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76353 = AXIS2_PLACEMENT_3D ( 'NONE', #5874, #84527, #7347 ) ; +#76354 = STYLED_ITEM ( 'NONE', ( #97050 ), #91464 ) ; +#76355 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76356 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311421000000000170, 0.8648700000000000276 ) ) ; +#76357 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #15730, #100395, #29569, #45356 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76358 = SURFACE_SIDE_STYLE ('',( #45190 ) ) ; +#76359 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#76360 = ORIENTED_EDGE ( 'NONE', *, *, #43481, .F. ) ; +#76362 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53942 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11992, #3436, #97793 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76361 = PRESENTATION_STYLE_ASSIGNMENT (( #37592 ) ) ; +#76363 = ADVANCED_FACE ( 'NONE', ( #81272 ), #40339, .T. ) ; +#76364 = FACE_OUTER_BOUND ( 'NONE', #3078, .T. ) ; +#76366 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#76365 = AXIS2_PLACEMENT_3D ( 'NONE', #84846, #86382, #77710 ) ; +#76367 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#76368 = EDGE_CURVE ( 'NONE', #53502, #28269, #97988, .T. ) ; +#76369 = VECTOR ( 'NONE', #38276, 1000.000000000000000 ) ; +#76370 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35532 ) ) ; +#76371 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87762 ), #89435 ) ; +#76372 = FILL_AREA_STYLE_COLOUR ( '', #9641 ) ; +#76373 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76374 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50346 ) ) ; +#76375 = ORIENTED_EDGE ( 'NONE', *, *, #28692, .F. ) ; +#76376 = PLANE ( 'NONE', #82384 ) ; +#76377 = STYLED_ITEM ( 'NONE', ( #34093 ), #41784 ) ; +#76378 = CARTESIAN_POINT ( 'NONE', ( 0.009882622001633050227, -1.368793146596559929, 0.8300000000000006262 ) ) ; +#76379 = SURFACE_STYLE_USAGE ( .BOTH. , #5402 ) ; +#76380 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94295 ), #89454 ) ; +#76381 = FILL_AREA_STYLE ('',( #59105 ) ) ; +#76382 = VERTEX_POINT ( 'NONE', #34307 ) ; +#76383 = EDGE_LOOP ( 'NONE', ( #94494, #86242, #12229, #71284, #41940, #54951 ) ) ; +#76384 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76385 = ORIENTED_EDGE ( 'NONE', *, *, #83409, .T. ) ; +#76386 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76387 = CARTESIAN_POINT ( 'NONE', ( 0.07744069998345409767, -1.407232784796780045, 0.8100000000000000533 ) ) ; +#76388 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76389 = CARTESIAN_POINT ( 'NONE', ( 0.4283467773376269938, -1.261010674219189998, 0.8100000000000000533 ) ) ; +#76390 = FILL_AREA_STYLE ('',( #22786 ) ) ; +#76391 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76392 = SURFACE_STYLE_USAGE ( .BOTH. , #45223 ) ; +#76393 = CIRCLE ( 'NONE', #32394, 0.009999999999999998473 ) ; +#76394 = DIRECTION ( 'NONE', ( 3.012399831378599940E-146, 4.591774807899559894E-33, 1.000000000000000000 ) ) ; +#76395 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7881 ), #48737 ) ; +#76396 = ORIENTED_EDGE ( 'NONE', *, *, #85518, .T. ) ; +#76397 = EDGE_CURVE ( 'NONE', #36882, #33894, #2251, .T. ) ; +#76398 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76399 = ORIENTED_EDGE ( 'NONE', *, *, #41232, .F. ) ; +#76400 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980549, 0.000000000000000000 ) ) ; +#76401 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60801, 'distance_accuracy_value', 'NONE'); +#76402 = SURFACE_SIDE_STYLE ('',( #4448 ) ) ; +#76403 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76404 = FACE_OUTER_BOUND ( 'NONE', #21875, .T. ) ; +#76405 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76406 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76407 = FILL_AREA_STYLE ('',( #99952 ) ) ; +#76408 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#76409 = STYLED_ITEM ( 'NONE', ( #86669 ), #32284 ) ; +#76410 = ORIENTED_EDGE ( 'NONE', *, *, #55635, .F. ) ; +#76412 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76411 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76413 = ORIENTED_EDGE ( 'NONE', *, *, #7497, .F. ) ; +#76414 = ORIENTED_EDGE ( 'NONE', *, *, #30908, .T. ) ; +#76415 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63421 ) ) ; +#76416 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85765 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26523, #51537, #66322 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76417 = ADVANCED_FACE ( 'NONE', ( #98963 ), #83753, .T. ) ; +#76418 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76420 = ORIENTED_EDGE ( 'NONE', *, *, #51973, .T. ) ; +#76419 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#76421 = VECTOR ( 'NONE', #51329, 1000.000000000000000 ) ; +#76422 = LINE ( 'NONE', #61648, #11079 ) ; +#76423 = STYLED_ITEM ( 'NONE', ( #3307 ), #84718 ) ; +#76424 = STYLED_ITEM ( 'NONE', ( #29888 ), #91878 ) ; +#76425 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#76426 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76427 = ORIENTED_EDGE ( 'NONE', *, *, #43359, .T. ) ; +#76429 = FILL_AREA_STYLE_COLOUR ( '', #63252 ) ; +#76428 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76430 = VERTEX_POINT ( 'NONE', #90392 ) ; +#76431 = VERTEX_POINT ( 'NONE', #91404 ) ; +#76432 = DIRECTION ( 'NONE', ( -0.7071060119555133694, -0.7071075504167448900, 0.000000000000000000 ) ) ; +#76434 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50401 ) ) ; +#76433 = SURFACE_STYLE_FILL_AREA ( #5940 ) ; +#76435 = EDGE_CURVE ( 'NONE', #21671, #74099, #44901, .T. ) ; +#76436 = SURFACE_STYLE_FILL_AREA ( #6910 ) ; +#76437 = STYLED_ITEM ( 'NONE', ( #96455 ), #5888 ) ; +#76438 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#76439 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76440 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#76441 = PRESENTATION_STYLE_ASSIGNMENT (( #69237 ) ) ; +#76442 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#76443 = SURFACE_STYLE_USAGE ( .BOTH. , #93239 ) ; +#76444 = AXIS2_PLACEMENT_3D ( 'NONE', #11564, #73949, #82124 ) ; +#76445 = ORIENTED_EDGE ( 'NONE', *, *, #64193, .F. ) ; +#76446 = ORIENTED_EDGE ( 'NONE', *, *, #78138, .F. ) ; +#76447 = EDGE_CURVE ( 'NONE', #65234, #24100, #84739, .T. ) ; +#76448 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76449 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#76450 = CARTESIAN_POINT ( 'NONE', ( 1.133718228224829927, -1.135808780994409961, 0.8299999999999999600 ) ) ; +#76451 = VECTOR ( 'NONE', #50802, 1000.000000000000114 ) ; +#76452 = DIRECTION ( 'NONE', ( -0.7071045084557405769, -0.7071090539100497452, 0.000000000000000000 ) ) ; +#76453 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76454 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76455 = VECTOR ( 'NONE', #6175, 1000.000000000000000 ) ; +#76456 = EDGE_CURVE ( 'NONE', #141, #95, #52125, .T. ) ; +#76457 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.7000000000000018430, 7.851278178449085673E-79 ) ) ; +#76458 = ORIENTED_EDGE ( 'NONE', *, *, #82939, .T. ) ; +#76459 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#76460 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76461 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#76462 = CARTESIAN_POINT ( 'NONE', ( 7.386066166500240726, 7.678361166500082824, 0.8991599999999999593 ) ) ; +#76463 = SURFACE_STYLE_FILL_AREA ( #68293 ) ; +#76464 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#76465 = FILL_AREA_STYLE ('',( #91289 ) ) ; +#76467 = EDGE_CURVE ( 'NONE', #42173, #10657, #68894, .T. ) ; +#76466 = PRESENTATION_STYLE_ASSIGNMENT (( #15667 ) ) ; +#76469 = ADVANCED_FACE ( 'NONE', ( #75103 ), #78782, .T. ) ; +#76468 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76470 = SURFACE_STYLE_FILL_AREA ( #44803 ) ; +#76471 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76472 = SURFACE_STYLE_FILL_AREA ( #23373 ) ; +#76473 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.123820061220085265, 0.000000000000000000 ) ) ; +#76475 = EDGE_CURVE ( 'NONE', #33080, #96200, #994, .T. ) ; +#76474 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86808 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29539, #21876, #14166 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76476 = EDGE_CURVE ( 'NONE', #94818, #40642, #39796, .T. ) ; +#76477 = PRESENTATION_STYLE_ASSIGNMENT (( #22880 ) ) ; +#76478 = LINE ( 'NONE', #27540, #74611 ) ; +#76479 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, 0.000000000000000000 ) ) ; +#76480 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76481 = ORIENTED_EDGE ( 'NONE', *, *, #58208, .F. ) ; +#76482 = SURFACE_STYLE_USAGE ( .BOTH. , #23379 ) ; +#76483 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76484 = FACE_OUTER_BOUND ( 'NONE', #100794, .T. ) ; +#76485 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.5000000000000000000, -13.54999999999999893 ) ) ; +#76486 = EDGE_CURVE ( 'NONE', #19897, #38594, #71445, .T. ) ; +#76487 = AXIS2_PLACEMENT_3D ( 'NONE', #64629, #32492, #16115 ) ; +#76488 = SURFACE_STYLE_USAGE ( .BOTH. , #68319 ) ; +#76489 = LINE ( 'NONE', #13128, #51438 ) ; +#76490 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 1.076179938779915135, -0.02000000000000000042 ) ) ; +#76491 = ADVANCED_FACE ( 'NONE', ( #38785 ), #86764, .F. ) ; +#76492 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.000000000000000000, 0.1900000000000000022 ) ) ; +#76493 = ORIENTED_EDGE ( 'NONE', *, *, #90525, .F. ) ; +#76494 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12810 ), #32504 ) ; +#76495 = LINE ( 'NONE', #75999, #67379 ) ; +#76496 = VECTOR ( 'NONE', #22001, 1000.000000000000000 ) ; +#76497 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13509 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76355, #79405, #9855 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76498 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76499 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76500 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76501 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#76502 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42282 ) ) ; +#76503 = LINE ( 'NONE', #1821, #57696 ) ; +#76504 = ORIENTED_EDGE ( 'NONE', *, *, #32233, .T. ) ; +#76505 = ORIENTED_EDGE ( 'NONE', *, *, #71924, .F. ) ; +#76506 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85793, #92912, #23028, #79156, #15825, #85287, #9124, #38844, #40366, #1561, #69962, #87310, #69441, #32701, #17346, #31176, #48537 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.492633351254385372E-05, 4.988459961574983259E-05, 6.202023387223290572E-05, 7.381064975063147200E-05, 8.522929490718605342E-05, 9.648269829191406734E-05, 0.0001074668139312722116, 0.0001183815562236710756, 0.0001293286825426075625, 0.0001405453271619777156, 0.0001521160265971611514, 0.0001642953361755828529, 0.0001773332741803570795, 0.0001914400125204008098 ), + .UNSPECIFIED. ) ; +#76507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52133 ) ) ; +#76508 = ORIENTED_EDGE ( 'NONE', *, *, #89145, .T. ) ; +#76509 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#76510 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76511 = FILL_AREA_STYLE ('',( #68829 ) ) ; +#76512 = SHAPE_DEFINITION_REPRESENTATION ( #28647, #29294 ) ; +#76513 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76514 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#76515 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76517 = ORIENTED_EDGE ( 'NONE', *, *, #89165, .T. ) ; +#76516 = EDGE_LOOP ( 'NONE', ( #68706, #13783, #62908, #29759 ) ) ; +#76518 = VECTOR ( 'NONE', #34187, 1000.000000000000000 ) ; +#76519 = ADVANCED_FACE ( 'NONE', ( #47959 ), #40319, .T. ) ; +#76520 = ORIENTED_EDGE ( 'NONE', *, *, #37259, .F. ) ; +#76521 = FILL_AREA_STYLE_COLOUR ( '', #36122 ) ; +#76522 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52248, 'distance_accuracy_value', 'NONE'); +#76523 = PRESENTATION_STYLE_ASSIGNMENT (( #61244 ) ) ; +#76525 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2849999999999999756, -0.1400000000000000133 ) ) ; +#76524 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 1.633333333333333304, 0.000000000000000000 ) ) ; +#76526 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60984 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100316, #52993, #22319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76527 = VERTEX_POINT ( 'NONE', #21203 ) ; +#76528 = EDGE_CURVE ( 'NONE', #10994, #35659, #87771, .T. ) ; +#76529 = EDGE_LOOP ( 'NONE', ( #62155, #70761, #77868, #36518 ) ) ; +#76530 = PRESENTATION_STYLE_ASSIGNMENT (( #45357 ) ) ; +#76531 = CARTESIAN_POINT ( 'NONE', ( 5.257674750250088458, 8.519818750250086836, 0.8648700000000000276 ) ) ; +#76533 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#76532 = FILL_AREA_STYLE_COLOUR ( '', #90518 ) ; +#76534 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76535 = ORIENTED_EDGE ( 'NONE', *, *, #47069, .T. ) ; +#76536 = CARTESIAN_POINT ( 'NONE', ( -0.5047584000990159581, -0.9806916243805300359, 0.8100000000000000533 ) ) ; +#76537 = VERTEX_POINT ( 'NONE', #12461 ) ; +#76538 = VERTEX_POINT ( 'NONE', #59569 ) ; +#76539 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24401 ) ) ; +#76540 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76542 = EDGE_LOOP ( 'NONE', ( #20597, #44070, #23110, #98629 ) ) ; +#76541 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76543 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76544 = PRESENTATION_STYLE_ASSIGNMENT (( #29101 ) ) ; +#76545 = ORIENTED_EDGE ( 'NONE', *, *, #20624, .F. ) ; +#76546 = CARTESIAN_POINT ( 'NONE', ( 0.001293116504768550062, -1.273483528256009967, 0.8299999999999999600 ) ) ; +#76547 = FILL_AREA_STYLE_COLOUR ( '', #77096 ) ; +#76548 = VERTEX_POINT ( 'NONE', #97759 ) ; +#76549 = ORIENTED_EDGE ( 'NONE', *, *, #100664, .T. ) ; +#76550 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76551 = EDGE_CURVE ( 'NONE', #212, #56185, #66165, .T. ) ; +#76552 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.000000000000000000, -0.2999999999999999889 ) ) ; +#76553 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#76554 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13499 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58968, #81933, #29293 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76555 = FACE_OUTER_BOUND ( 'NONE', #44357, .T. ) ; +#76556 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #53752, #9221 ), + ( #94543, #48117 ), + ( #79260, #38940 ), + ( #39953, #55786 ), + ( #15424, #85393 ), + ( #8210, #24152 ), + ( #39433, #56314 ), + ( #69554, #71094 ), + ( #85897, #46580 ), + ( #94015, #78740 ), + ( #86924, #8706 ), + ( #86411, #1133 ), + ( #70062, #55300 ), + ( #23131, #47608 ), + ( #78258, #63946 ), + ( #32295, #120 ), + ( #77737, #71604 ), + ( #63466, #31269 ), + ( #24663, #16939 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07371267057028850489, 0.1427176704673379926, 0.2082134058714990021, 0.2705027277892230186, 0.3304959100989089960, 0.3889789042896930060, 0.4458964732700330114, 0.5023682877331400176, 0.5591912362163320438, 0.6167818134451880097, 0.6762489342310300522, 0.7375288950348040107, 0.8004750105796289983, 0.8650547179286960375, 0.9315767411187479974, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76557 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, 1.048695503451051965E-76 ) ) ; +#76558 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92842 ) ) ; +#76559 = VECTOR ( 'NONE', #67006, 1000.000000000000000 ) ; +#76560 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76561 = SURFACE_STYLE_USAGE ( .BOTH. , #85731 ) ; +#76562 = ORIENTED_EDGE ( 'NONE', *, *, #18992, .T. ) ; +#76563 = SURFACE_SIDE_STYLE ('',( #86240 ) ) ; +#76564 = CARTESIAN_POINT ( 'NONE', ( -0.9573895083907240089, -1.450479623942970253, 0.8100000000000000533 ) ) ; +#76565 = ORIENTED_EDGE ( 'NONE', *, *, #62300, .T. ) ; +#76567 = PRESENTATION_STYLE_ASSIGNMENT (( #84244 ) ) ; +#76566 = VECTOR ( 'NONE', #100046, 1000.000000000000000 ) ; +#76568 = FILL_AREA_STYLE ('',( #69904 ) ) ; +#76569 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24431 ) ) ; +#76570 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, -3.149999999999979927, 0.000000000000000000 ) ) ; +#76571 = FILL_AREA_STYLE ('',( #45398 ) ) ; +#76573 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#76572 = SURFACE_STYLE_FILL_AREA ( #5098 ) ; +#76574 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#76575 = LINE ( 'NONE', #43932, #94019 ) ; +#76576 = EDGE_CURVE ( 'NONE', #68842, #78654, #27898, .T. ) ; +#76577 = FILL_AREA_STYLE ('',( #51638 ) ) ; +#76578 = PRESENTATION_STYLE_ASSIGNMENT (( #84743 ) ) ; +#76579 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63572 ) ) ; +#76580 = SURFACE_SIDE_STYLE ('',( #100445 ) ) ; +#76581 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#76582 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76583 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76584 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76585 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#76586 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50847, #81986, #69098, #92596 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76587 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#76588 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99125 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64283, #34676, #10554 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76589 = LINE ( 'NONE', #91418, #37543 ) ; +#76590 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76591 = FACE_OUTER_BOUND ( 'NONE', #25206, .T. ) ; +#76592 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19539 ) ) ; +#76593 = EDGE_CURVE ( 'NONE', #8122, #90078, #36051, .T. ) ; +#76594 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16044, #70179, #64062, #95152 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76595 = ORIENTED_EDGE ( 'NONE', *, *, #35142, .T. ) ; +#76596 = CARTESIAN_POINT ( 'NONE', ( -1.010125602507139897, -1.400043273498619900, 0.8299999999999999600 ) ) ; +#76597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14317, 'distance_accuracy_value', 'NONE'); +#76598 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73232, 'distance_accuracy_value', 'NONE'); +#76599 = LINE ( 'NONE', #5116, #95291 ) ; +#76600 = LINE ( 'NONE', #11106, #33833 ) ; +#76601 = SURFACE_STYLE_FILL_AREA ( #6094 ) ; +#76602 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14317, #68962, #44977 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76603 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76604 = FACE_OUTER_BOUND ( 'NONE', #25797, .T. ) ; +#76605 = SURFACE_STYLE_FILL_AREA ( #53142 ) ; +#76606 = LINE ( 'NONE', #12751, #99309 ) ; +#76607 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#76608 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19556 ) ) ; +#76609 = EDGE_CURVE ( 'NONE', #37284, #64661, #89658, .T. ) ; +#76610 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#76611 = ORIENTED_EDGE ( 'NONE', *, *, #79207, .T. ) ; +#76612 = EDGE_LOOP ( 'NONE', ( #96623, #8394, #89253, #53660 ) ) ; +#76613 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999356, -0.01085786437626905590, -0.2500000000000000555 ) ) ; +#76614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12772, 'distance_accuracy_value', 'NONE'); +#76615 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9838, 'distance_accuracy_value', 'NONE'); +#76616 = VECTOR ( 'NONE', #19633, 1000.000000000000000 ) ; +#76617 = PRESENTATION_STYLE_ASSIGNMENT (( #86295 ) ) ; +#76618 = FACE_OUTER_BOUND ( 'NONE', #87280, .T. ) ; +#76619 = FILL_AREA_STYLE ('',( #67936 ) ) ; +#76620 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#76621 = PRESENTATION_STYLE_ASSIGNMENT (( #14290 ) ) ; +#76622 = ORIENTED_EDGE ( 'NONE', *, *, #85444, .T. ) ; +#76623 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76624 = SURFACE_SIDE_STYLE ('',( #83806 ) ) ; +#76625 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76626 = VERTEX_POINT ( 'NONE', #11449 ) ; +#76627 = SURFACE_SIDE_STYLE ('',( #14297 ) ) ; +#76628 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.800000000000000711, 0.000000000000000000 ) ) ; +#76629 = ORIENTED_EDGE ( 'NONE', *, *, #27701, .F. ) ; +#76630 = LINE ( 'NONE', #22510, #5995 ) ; +#76631 = CARTESIAN_POINT ( 'NONE', ( 3.949526999999999344, 4.397386000000000905, 0.8991599999999999593 ) ) ; +#76632 = AXIS2_PLACEMENT_3D ( 'NONE', #90637, #60021, #27872 ) ; +#76633 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24582 ) ) ; +#76634 = SURFACE_SIDE_STYLE ('',( #36352 ) ) ; +#76636 = EDGE_CURVE ( 'NONE', #33415, #92379, #36552, .T. ) ; +#76635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99363 ), #55548 ) ; +#76637 = CARTESIAN_POINT ( 'NONE', ( 5.257799999999999585, 10.85342000000000162, 0.8991599999999999593 ) ) ; +#76638 = DIRECTION ( 'NONE', ( 1.853357274465659969E-67, -1.000000000000000000, 4.266452400824600274E-34 ) ) ; +#76640 = ORIENTED_EDGE ( 'NONE', *, *, #67471, .T. ) ; +#76639 = ORIENTED_EDGE ( 'NONE', *, *, #36324, .T. ) ; +#76641 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30412 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60759, #21930, #53090 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76642 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#76643 = FILL_AREA_STYLE_COLOUR ( '', #51185 ) ; +#76644 = ORIENTED_EDGE ( 'NONE', *, *, #59794, .T. ) ; +#76645 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#76646 = VECTOR ( 'NONE', #14859, 1000.000000000000000 ) ; +#76647 = STYLED_ITEM ( 'NONE', ( #67271 ), #81648 ) ; +#76649 = CARTESIAN_POINT ( 'NONE', ( -0.4939768715539690214, -0.9855649010623360740, 0.8299999999999999600 ) ) ; +#76648 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76650 = VERTEX_POINT ( 'NONE', #43175 ) ; +#76651 = EDGE_CURVE ( 'NONE', #77835, #53179, #17802, .T. ) ; +#76652 = EDGE_LOOP ( 'NONE', ( #6890, #12066, #94378, #84931 ) ) ; +#76653 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#76654 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#76655 = PRESENTATION_STYLE_ASSIGNMENT (( #70497 ) ) ; +#76656 = SURFACE_SIDE_STYLE ('',( #60377 ) ) ; +#76657 = VECTOR ( 'NONE', #79646, 1000.000000000000000 ) ; +#76658 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#76659 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#76660 = EDGE_LOOP ( 'NONE', ( #45737, #70434, #29332, #97982 ) ) ; +#76661 = ORIENTED_EDGE ( 'NONE', *, *, #96736, .F. ) ; +#76662 = SURFACE_SIDE_STYLE ('',( #99549 ) ) ; +#76663 = VERTEX_POINT ( 'NONE', #97283 ) ; +#76664 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#76665 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52212 ) ) ; +#76666 = STYLED_ITEM ( 'NONE', ( #79895 ), #1818 ) ; +#76667 = VECTOR ( 'NONE', #79577, 1000.000000000000000 ) ; +#76669 = ORIENTED_EDGE ( 'NONE', *, *, #96902, .F. ) ; +#76668 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76670 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19614 ) ) ; +#76671 = SURFACE_STYLE_USAGE ( .BOTH. , #45487 ) ; +#76672 = LINE ( 'NONE', #84825, #48144 ) ; +#76673 = ORIENTED_EDGE ( 'NONE', *, *, #57537, .F. ) ; +#76674 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#76675 = SURFACE_STYLE_FILL_AREA ( #67491 ) ; +#76676 = VERTEX_POINT ( 'NONE', #82507 ) ; +#76677 = SURFACE_SIDE_STYLE ('',( #68506 ) ) ; +#76678 = PLANE ( 'NONE', #23623 ) ; +#76679 = EDGE_CURVE ( 'NONE', #81243, #47482, #95394, .T. ) ; +#76681 = VERTEX_POINT ( 'NONE', #28374 ) ; +#76680 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#76682 = STYLED_ITEM ( 'NONE', ( #89684 ), #9997 ) ; +#76683 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76684 = SURFACE_SIDE_STYLE ('',( #92969 ) ) ; +#76685 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76686 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76687 = ORIENTED_EDGE ( 'NONE', *, *, #49645, .F. ) ; +#76688 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34321 ) ) ; +#76689 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76691 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333333304, 2.500000000000000000, 1.747825839085088807E-76 ) ) ; +#76690 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76692 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#76693 = SURFACE_STYLE_USAGE ( .BOTH. , #28724 ) ; +#76694 = EDGE_CURVE ( 'NONE', #31104, #41000, #67160, .T. ) ; +#76695 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76696 = ADVANCED_FACE ( 'NONE', ( #50868 ), #2006, .F. ) ; +#76697 = AXIS2_PLACEMENT_3D ( 'NONE', #29361, #45140, #44654 ) ; +#76698 = STYLED_ITEM ( 'NONE', ( #98288 ), #33395 ) ; +#76699 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76700 = SURFACE_STYLE_FILL_AREA ( #51742 ) ; +#76701 = ORIENTED_EDGE ( 'NONE', *, *, #52042, .T. ) ; +#76702 = CARTESIAN_POINT ( 'NONE', ( 1.162161998062432700, 1.364349903361321781, 0.8100000000000001643 ) ) ; +#76703 = STYLED_ITEM ( 'NONE', ( #61014 ), #86275 ) ; +#76704 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26236 ) ) ; +#76705 = ORIENTED_EDGE ( 'NONE', *, *, #47163, .F. ) ; +#76706 = VECTOR ( 'NONE', #95913, 1000.000000000000000 ) ; +#76707 = FILL_AREA_STYLE_COLOUR ( '', #49140 ) ; +#76708 = SURFACE_SIDE_STYLE ('',( #14384 ) ) ; +#76709 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78336 ) ) ; +#76710 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#76711 = EDGE_CURVE ( 'NONE', #8544, #10422, #74338, .T. ) ; +#76712 = STYLED_ITEM ( 'NONE', ( #28605 ), #94308 ) ; +#76713 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722699999999918, 0.8991599999999999593 ) ) ; +#76714 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80040 ), #4984 ) ; +#76715 = EDGE_LOOP ( 'NONE', ( #13866, #16897, #46233, #2794, #9906, #67746 ) ) ; +#76716 = FILL_AREA_STYLE_COLOUR ( '', #63659 ) ; +#76717 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39260 ) ) ; +#76718 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#76719 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76720 = SURFACE_STYLE_FILL_AREA ( #60931 ) ; +#76721 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76722 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76723 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#76724 = PLANE ( 'NONE', #6060 ) ; +#76725 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#76726 = LINE ( 'NONE', #69031, #52455 ) ; +#76727 = VECTOR ( 'NONE', #2292, 1000.000000000000000 ) ; +#76728 = FILL_AREA_STYLE_COLOUR ( '', #71873 ) ; +#76729 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#76730 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76731 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72354, 'distance_accuracy_value', 'NONE'); +#76732 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#76733 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8199999999999999512 ) ) ; +#76734 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #415 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7191, #99115, #53743 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76735 = VERTEX_POINT ( 'NONE', #100199 ) ; +#76736 = PLANE ( 'NONE', #62797 ) ; +#76737 = ORIENTED_EDGE ( 'NONE', *, *, #30948, .T. ) ; +#76738 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51938, 'distance_accuracy_value', 'NONE'); +#76739 = AXIS2_PLACEMENT_3D ( 'NONE', #49310, #24337, #86080 ) ; +#76741 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6945, 'distance_accuracy_value', 'NONE'); +#76742 = CARTESIAN_POINT ( 'NONE', ( 1.092224350139350264, -0.9825712221600161334, 0.8100000000000000533 ) ) ; +#76743 = FILL_AREA_STYLE_COLOUR ( '', #57987 ) ; +#76744 = FILL_AREA_STYLE ('',( #84406 ) ) ; +#76745 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.476179938779914824, -0.02000000000000000042 ) ) ; +#76746 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8648700000000000276 ) ) ; +#76747 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, 3.099999999999994316, 0.000000000000000000 ) ) ; +#76748 = ORIENTED_EDGE ( 'NONE', *, *, #4118, .F. ) ; +#76749 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#76750 = LINE ( 'NONE', #53284, #11118 ) ; +#76751 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59555, 'distance_accuracy_value', 'NONE'); +#76752 = PLANE ( 'NONE', #23186 ) ; +#76753 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82783 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72223, #71209, #63587 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76754 = ORIENTED_EDGE ( 'NONE', *, *, #73051, .T. ) ; +#76755 = SURFACE_SIDE_STYLE ('',( #69053 ) ) ; +#76756 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#76757 = FILL_AREA_STYLE ('',( #7728 ) ) ; +#76758 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76759 = ADVANCED_FACE ( 'NONE', ( #22715 ), #29854, .F. ) ; +#76760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76761 = FILL_AREA_STYLE_COLOUR ( '', #26957 ) ; +#76762 = EDGE_LOOP ( 'NONE', ( #98438, #39030, #80833, #4978, #83569, #98142 ) ) ; +#76763 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76764 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88037, 'distance_accuracy_value', 'NONE'); +#76765 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4849999999999999867, -0.2399999999999999911 ) ) ; +#76766 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76767 = SURFACE_STYLE_USAGE ( .BOTH. , #84431 ) ; +#76768 = EDGE_CURVE ( 'NONE', #82331, #94599, #31539, .T. ) ; +#76769 = ORIENTED_EDGE ( 'NONE', *, *, #35099, .F. ) ; +#76770 = SURFACE_STYLE_FILL_AREA ( #14942 ) ; +#76771 = SURFACE_SIDE_STYLE ('',( #38987 ) ) ; +#76772 = STYLED_ITEM ( 'NONE', ( #35432 ), #18246 ) ; +#76773 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76774 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76775 = SURFACE_SIDE_STYLE ('',( #29316 ) ) ; +#76776 = CARTESIAN_POINT ( 'NONE', ( 1.516559913281009919, -1.413990021526319918, 0.8300000000000001821 ) ) ; +#76777 = ORIENTED_EDGE ( 'NONE', *, *, #68379, .F. ) ; +#76778 = FILL_AREA_STYLE_COLOUR ( '', #98664 ) ; +#76779 = PRODUCT ( 'Submodel-C0201_part_C0201', 'Submodel-C0201_part_C0201', '', ( #87209 ) ) ; +#76780 = ORIENTED_EDGE ( 'NONE', *, *, #50387, .T. ) ; +#76781 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #89304, #4027, #64806, #42346 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76782 = VECTOR ( 'NONE', #82737, 1000.000000000000114 ) ; +#76783 = ORIENTED_EDGE ( 'NONE', *, *, #91874, .T. ) ; +#76785 = ORIENTED_EDGE ( 'NONE', *, *, #68059, .F. ) ; +#76784 = LINE ( 'NONE', #54318, #44406 ) ; +#76786 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#76787 = CARTESIAN_POINT ( 'NONE', ( 0.9685869866146575857, 0.4055590759269656620, 0.8299999999999999600 ) ) ; +#76788 = FILL_AREA_STYLE ('',( #92584 ) ) ; +#76789 = ORIENTED_EDGE ( 'NONE', *, *, #66050, .T. ) ; +#76790 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76791 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.149999999999999911, 0.000000000000000000 ) ) ; +#76792 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.8999999999999991340, 4.860315062863665657E-79 ) ) ; +#76793 = ORIENTED_EDGE ( 'NONE', *, *, #53618, .T. ) ; +#76794 = AXIS2_PLACEMENT_3D ( 'NONE', #74795, #5294, #5801 ) ; +#76795 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000011470, 0.7499999999859485733, 0.6999285677838846809 ) ) ; +#76796 = FACE_OUTER_BOUND ( 'NONE', #21431, .T. ) ; +#76797 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76798 = ORIENTED_EDGE ( 'NONE', *, *, #61920, .F. ) ; +#76799 = VECTOR ( 'NONE', #1260, 1000.000000000000000 ) ; +#76801 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 15.15000000000000036, 0.000000000000000000 ) ) ; +#76800 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#76802 = ORIENTED_EDGE ( 'NONE', *, *, #13336, .F. ) ; +#76803 = EDGE_CURVE ( 'NONE', #95213, #39315, #68149, .T. ) ; +#76804 = EDGE_CURVE ( 'NONE', #32731, #59034, #99225, .T. ) ; +#76806 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.35000000000000142, 0.000000000000000000 ) ) ; +#76805 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#76807 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13369 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90021, #89542, #98118 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76808 = CARTESIAN_POINT ( 'NONE', ( 0.09278135453971496360, -1.258125650529932527, 0.8099999999998603872 ) ) ; +#76809 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#76810 = ORIENTED_EDGE ( 'NONE', *, *, #17422, .T. ) ; +#76811 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76812 = ORIENTED_EDGE ( 'NONE', *, *, #94456, .T. ) ; +#76813 = SURFACE_SIDE_STYLE ('',( #38028 ) ) ; +#76814 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19768 ) ) ; +#76815 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76816 = ADVANCED_FACE ( 'NONE', ( #69654 ), #53859, .T. ) ; +#76817 = ADVANCED_FACE ( 'NONE', ( #92620 ), #61039, .F. ) ; +#76818 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42618, 'distance_accuracy_value', 'NONE'); +#76819 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91545 ) ) ; +#76820 = SURFACE_STYLE_FILL_AREA ( #14986 ) ; +#76821 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8648700000000000276 ) ) ; +#76822 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -1.300000000000000266, 0.8299999999999999600 ) ) ; +#76823 = AXIS2_PLACEMENT_3D ( 'NONE', #20391, #21400, #13675 ) ; +#76825 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76824 = CIRCLE ( 'NONE', #75031, 0.009999999999999998473 ) ; +#76826 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#76827 = CARTESIAN_POINT ( 'NONE', ( 1.338207848547039891, -1.047446665233070062, 0.8100000000000000533 ) ) ; +#76828 = FACE_OUTER_BOUND ( 'NONE', #21328, .T. ) ; +#76829 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76830 = VERTEX_POINT ( 'NONE', #6796 ) ; +#76831 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#76833 = FILL_AREA_STYLE ('',( #29855 ) ) ; +#76832 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76834 = SURFACE_STYLE_FILL_AREA ( #66785 ) ; +#76835 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94743 ) ) ; +#76836 = LINE ( 'NONE', #68153, #71331 ) ; +#76837 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76838 = EDGE_CURVE ( 'NONE', #87237, #68202, #70389, .T. ) ; +#76839 = LINE ( 'NONE', #6804, #4454 ) ; +#76840 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76841 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76842 = VERTEX_POINT ( 'NONE', #94652 ) ; +#76844 = EDGE_CURVE ( 'NONE', #90252, #16380, #71699, .T. ) ; +#76843 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, -0.1444665087776849932, 1.013711183678429162 ) ) ; +#76845 = PLANE ( 'NONE', #61100 ) ; +#76846 = FILL_AREA_STYLE_COLOUR ( '', #90262 ) ; +#76847 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76848 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76849 = VECTOR ( 'NONE', #16331, 1000.000000000000000 ) ; +#76850 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76851 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39266, 'distance_accuracy_value', 'NONE'); +#76852 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#76853 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76854 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76855 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76856 = LINE ( 'NONE', #5363, #80585 ) ; +#76857 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76858 = STYLED_ITEM ( 'NONE', ( #24106 ), #86619 ) ; +#76859 = ADVANCED_FACE ( 'NONE', ( #47709 ), #47196, .T. ) ; +#76860 = VECTOR ( 'NONE', #23619, 1000.000000000000000 ) ; +#76861 = SURFACE_STYLE_USAGE ( .BOTH. , #46178 ) ; +#76862 = PLANE ( 'NONE', #84738 ) ; +#76863 = ADVANCED_FACE ( 'NONE', ( #24254 ), #78850, .F. ) ; +#76864 = FILL_AREA_STYLE ('',( #1271 ) ) ; +#76865 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1170, 'distance_accuracy_value', 'NONE'); +#76866 = VECTOR ( 'NONE', #49340, 1000.000000000000000 ) ; +#76867 = SURFACE_STYLE_FILL_AREA ( #28892 ) ; +#76868 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999993072, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#76869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46596, 'distance_accuracy_value', 'NONE'); +#76870 = EDGE_CURVE ( 'NONE', #96609, #33923, #56081, .T. ) ; +#76871 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82280 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41957, #49114, #19465 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76872 = SURFACE_SIDE_STYLE ('',( #45681 ) ) ; +#76873 = FILL_AREA_STYLE ('',( #22753 ) ) ; +#76874 = LINE ( 'NONE', #62084, #37340 ) ; +#76875 = SURFACE_SIDE_STYLE ('',( #15033 ) ) ; +#76876 = SURFACE_STYLE_FILL_AREA ( #91191 ) ; +#76877 = VERTEX_POINT ( 'NONE', #87208 ) ; +#76878 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #67765 ) ) ; +#76879 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76880 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#76881 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3258, 'distance_accuracy_value', 'NONE'); +#76882 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33708, #95941, #3049, #57716 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76883 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#76884 = VECTOR ( 'NONE', #44438, 1000.000000000000000 ) ; +#76885 = VERTEX_POINT ( 'NONE', #64724 ) ; +#76886 = CARTESIAN_POINT ( 'NONE', ( -0.08168056302834829363, -0.9656914468017120390, 0.8300000000000002931 ) ) ; +#76887 = CYLINDRICAL_SURFACE ( 'NONE', #17355, 0.009999999999999998473 ) ; +#76888 = ADVANCED_FACE ( 'NONE', ( #78523 ), #17237, .T. ) ; +#76889 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.300000000000000266, 4.112574283980952083E-79 ) ) ; +#76891 = ORIENTED_EDGE ( 'NONE', *, *, #37205, .T. ) ; +#76890 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85899 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91117, #28340, #31841 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76892 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 14.25000000000000000, 0.000000000000000000 ) ) ; +#76893 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40044, 'distance_accuracy_value', 'NONE'); +#76894 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76895 = SURFACE_STYLE_FILL_AREA ( #31950 ) ; +#76896 = EDGE_CURVE ( 'NONE', #43863, #24062, #71898, .T. ) ; +#76897 = ORIENTED_EDGE ( 'NONE', *, *, #71663, .T. ) ; +#76898 = ORIENTED_EDGE ( 'NONE', *, *, #17557, .F. ) ; +#76899 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76900 = ORIENTED_EDGE ( 'NONE', *, *, #77748, .T. ) ; +#76902 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -13.35000000000000142 ) ) ; +#76901 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76903 = CARTESIAN_POINT ( 'NONE', ( 0.09306199881179780253, -1.350767436372750208, 0.8299999999999999600 ) ) ; +#76904 = ADVANCED_FACE ( 'NONE', ( #1942 ), #48923, .T. ) ; +#76905 = CARTESIAN_POINT ( 'NONE', ( 0.5194035290631999757, -1.172439657072400054, 0.8100000000000000533 ) ) ; +#76906 = SURFACE_SIDE_STYLE ('',( #53931 ) ) ; +#76907 = FILL_AREA_STYLE ('',( #29441 ) ) ; +#76908 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6699 ) ) ; +#76909 = LINE ( 'NONE', #6866, #93614 ) ; +#76910 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #82704, #12501 ) ; +#76911 = VERTEX_POINT ( 'NONE', #86699 ) ; +#76912 = EDGE_CURVE ( 'NONE', #88816, #99634, #60660, .T. ) ; +#76913 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80226 ), #72049 ) ; +#76914 = ORIENTED_EDGE ( 'NONE', *, *, #39640, .T. ) ; +#76915 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#76916 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76917 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#76918 = SURFACE_STYLE_FILL_AREA ( #45727 ) ; +#76919 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#76920 = LINE ( 'NONE', #85071, #86447 ) ; +#76921 = AXIS2_PLACEMENT_3D ( 'NONE', #9696, #72079, #31244 ) ; +#76922 = AXIS2_PLACEMENT_3D ( 'NONE', #45344, #39223, #29559 ) ; +#76923 = SURFACE_STYLE_FILL_AREA ( #38618 ) ; +#76924 = EDGE_LOOP ( 'NONE', ( #90868, #23827, #53244, #74548, #77172, #76802, #61138, #85921 ) ) ; +#76925 = FACE_OUTER_BOUND ( 'NONE', #72522, .T. ) ; +#76926 = VERTEX_POINT ( 'NONE', #58614 ) ; +#76927 = EDGE_CURVE ( 'NONE', #47667, #15739, #81083, .T. ) ; +#76928 = ORIENTED_EDGE ( 'NONE', *, *, #55035, .F. ) ; +#76929 = EDGE_CURVE ( 'NONE', #12458, #98893, #66241, .T. ) ; +#76930 = STYLED_ITEM ( 'NONE', ( #57029 ), #86803 ) ; +#76931 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70427 ) ) ; +#76932 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#76933 = PRESENTATION_STYLE_ASSIGNMENT (( #39134 ) ) ; +#76934 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #11525 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#76935 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#76936 = AXIS2_PLACEMENT_3D ( 'NONE', #65116, #97237, #34508 ) ; +#76938 = ORIENTED_EDGE ( 'NONE', *, *, #80510, .T. ) ; +#76937 = SURFACE_STYLE_USAGE ( .BOTH. , #78822 ) ; +#76939 = LINE ( 'NONE', #39642, #32006 ) ; +#76940 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#76941 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#76942 = SURFACE_STYLE_USAGE ( .BOTH. , #37153 ) ; +#76943 = VECTOR ( 'NONE', #74423, 1000.000000000000000 ) ; +#76944 = ORIENTED_EDGE ( 'NONE', *, *, #42717, .T. ) ; +#76946 = SURFACE_STYLE_USAGE ( .BOTH. , #98338 ) ; +#76945 = FILL_AREA_STYLE_COLOUR ( '', #31922 ) ; +#76947 = LINE ( 'NONE', #62655, #75576 ) ; +#76948 = ORIENTED_EDGE ( 'NONE', *, *, #62668, .F. ) ; +#76950 = ORIENTED_EDGE ( 'NONE', *, *, #26958, .F. ) ; +#76949 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99453, #46399, #14222, #67873 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#76951 = SURFACE_STYLE_USAGE ( .BOTH. , #92728 ) ; +#76952 = CARTESIAN_POINT ( 'NONE', ( 1.068987518412940263, -1.485874691073119980, 0.8100000000000000533 ) ) ; +#76953 = PLANE ( 'NONE', #23825 ) ; +#76954 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#76955 = ADVANCED_FACE ( 'NONE', ( #19252 ), #11522, .T. ) ; +#76956 = LINE ( 'NONE', #62664, #71121 ) ; +#76957 = AXIS2_PLACEMENT_3D ( 'NONE', #66335, #43844, #51037 ) ; +#76958 = SURFACE_SIDE_STYLE ('',( #45763 ) ) ; +#76959 = FACE_OUTER_BOUND ( 'NONE', #74292, .T. ) ; +#76960 = VERTEX_POINT ( 'NONE', #74407 ) ; +#76961 = EDGE_LOOP ( 'NONE', ( #74917, #80494, #10403, #3067, #50818, #62420 ) ) ; +#76962 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8099999999998959144 ) ) ; +#76963 = CARTESIAN_POINT ( 'NONE', ( 1.060135477854049935, -1.070174563215090080, 0.8100000000000000533 ) ) ; +#76964 = SURFACE_SIDE_STYLE ('',( #22328 ) ) ; +#76965 = LINE ( 'NONE', #12600, #12509 ) ; +#76966 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61339 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31801, #94572, #70602 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#76967 = ORIENTED_EDGE ( 'NONE', *, *, #88991, .T. ) ; +#76969 = ADVANCED_FACE ( 'NONE', ( #98306 ), #57612, .T. ) ; +#76968 = PRESENTATION_STYLE_ASSIGNMENT (( #68287 ) ) ; +#76970 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#76971 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5238200612200850648, 0.000000000000000000 ) ) ; +#76972 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76973 = VECTOR ( 'NONE', #72109, 1000.000000000000114 ) ; +#76974 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#76975 = CARTESIAN_POINT ( 'NONE', ( 1.806468873558769950, -1.190451802854979979, 0.8299999999999999600 ) ) ; +#76976 = PLANE ( 'NONE', #1816 ) ; +#76977 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#76978 = EDGE_CURVE ( 'NONE', #30895, #20936, #76909, .T. ) ; +#76979 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#76980 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#76981 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#76982 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40871, 'distance_accuracy_value', 'NONE'); +#76983 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#76984 = PLANE ( 'NONE', #91079 ) ; +#76985 = CARTESIAN_POINT ( 'NONE', ( -0.9896879621259911941, -0.9410130125528604061, 0.8100000000000316946 ) ) ; +#76986 = VERTEX_POINT ( 'NONE', #32338 ) ; +#76987 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#76988 = FILL_AREA_STYLE ('',( #99377 ) ) ; +#76989 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2808578643762690841, 0.1499999999999999389 ) ) ; +#76990 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#76991 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70027, 'distance_accuracy_value', 'NONE'); +#76992 = STYLED_ITEM ( 'NONE', ( #15977 ), #34519 ) ; +#76993 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#76994 = CARTESIAN_POINT ( 'NONE', ( 1.379746639148478060, -1.211946142803215221, 0.8099999999998568345 ) ) ; +#76995 = AXIS2_PLACEMENT_3D ( 'NONE', #42787, #18773, #58144 ) ; +#76996 = AXIS2_PLACEMENT_3D ( 'NONE', #98108, #28249, #12335 ) ; +#76997 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#76998 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18308 ) ) ; +#76999 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77000 = VERTEX_POINT ( 'NONE', #5902 ) ; +#77001 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8991599999999999593 ) ) ; +#77002 = STYLED_ITEM ( 'NONE', ( #100636 ), #59098 ) ; +#77003 = FACE_OUTER_BOUND ( 'NONE', #99621, .T. ) ; +#77004 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11649, 'distance_accuracy_value', 'NONE'); +#77005 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77006 = VECTOR ( 'NONE', #80340, 1000.000000000000114 ) ; +#77007 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3187, 'distance_accuracy_value', 'NONE'); +#77008 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77009 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#77010 = EDGE_CURVE ( 'NONE', #61247, #67952, #86324, .T. ) ; +#77011 = AXIS2_PLACEMENT_3D ( 'NONE', #17288, #31617, #980 ) ; +#77012 = EDGE_LOOP ( 'NONE', ( #42872, #21921, #93913, #94453 ) ) ; +#77013 = ORIENTED_EDGE ( 'NONE', *, *, #8380, .F. ) ; +#77014 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59141 ) ) ; +#77015 = ORIENTED_EDGE ( 'NONE', *, *, #21506, .F. ) ; +#77016 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77017 = ADVANCED_FACE ( 'NONE', ( #86965 ), #55828, .T. ) ; +#77018 = FILL_AREA_STYLE ('',( #14182 ) ) ; +#77019 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#77020 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77021 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86247 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77755, #8720, #1681 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77022 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #56088 ) ; +#77023 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#77024 = SURFACE_STYLE_USAGE ( .BOTH. , #61235 ) ; +#77026 = EDGE_LOOP ( 'NONE', ( #57500, #64647, #2459, #70291 ) ) ; +#77025 = ORIENTED_EDGE ( 'NONE', *, *, #82354, .T. ) ; +#77027 = ADVANCED_FACE ( 'NONE', ( #69192 ), #67718, .F. ) ; +#77028 = VECTOR ( 'NONE', #64888, 1000.000000000000000 ) ; +#77029 = EDGE_LOOP ( 'NONE', ( #43260, #21270, #54621, #91257 ) ) ; +#77030 = LINE ( 'NONE', #61737, #39287 ) ; +#77031 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#77033 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#77032 = CARTESIAN_POINT ( 'NONE', ( 7.386066124875000583, 9.092575124875001080, 0.8991599999999999593 ) ) ; +#77034 = VERTEX_POINT ( 'NONE', #52942 ) ; +#77035 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77036 = EDGE_CURVE ( 'NONE', #35982, #60955, #92684, .T. ) ; +#77037 = ORIENTED_EDGE ( 'NONE', *, *, #34327, .F. ) ; +#77038 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77039 = LINE ( 'NONE', #46883, #36590 ) ; +#77040 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45095 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81656, #96413, #42336 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77041 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -0.9000000000000001332, 0.000000000000000000 ) ) ; +#77042 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19972 ) ) ; +#77043 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77044 = ORIENTED_EDGE ( 'NONE', *, *, #74326, .T. ) ; +#77045 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#77046 = ORIENTED_EDGE ( 'NONE', *, *, #100677, .T. ) ; +#77047 = EDGE_CURVE ( 'NONE', #63967, #27159, #13537, .T. ) ; +#77048 = ORIENTED_EDGE ( 'NONE', *, *, #83429, .F. ) ; +#77049 = EDGE_CURVE ( 'NONE', #6059, #23968, #29443, .T. ) ; +#77050 = PRESENTATION_STYLE_ASSIGNMENT (( #45865 ) ) ; +#77052 = EDGE_CURVE ( 'NONE', #20312, #11817, #41022, .T. ) ; +#77051 = VERTEX_POINT ( 'NONE', #26705 ) ; +#77053 = EDGE_CURVE ( 'NONE', #43255, #42861, #61739, .T. ) ; +#77054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77055 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77056 = ORIENTED_EDGE ( 'NONE', *, *, #34551, .T. ) ; +#77057 = CARTESIAN_POINT ( 'NONE', ( 0.01558441558441510215, -1.332102272727269998, 0.8299999999999999600 ) ) ; +#77058 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77059 = ORIENTED_EDGE ( 'NONE', *, *, #4470, .T. ) ; +#77060 = ORIENTED_EDGE ( 'NONE', *, *, #44183, .T. ) ; +#77062 = FILL_AREA_STYLE_COLOUR ( '', #48713 ) ; +#77061 = PRESENTATION_STYLE_ASSIGNMENT (( #12822 ) ) ; +#77063 = FILL_AREA_STYLE ('',( #54094 ) ) ; +#77064 = PRESENTATION_STYLE_ASSIGNMENT (( #20426 ) ) ; +#77065 = EDGE_CURVE ( 'NONE', #32847, #13170, #95084, .T. ) ; +#77066 = VECTOR ( 'NONE', #78412, 1000.000000000000000 ) ; +#77067 = VECTOR ( 'NONE', #62554, 1000.000000000000000 ) ; +#77068 = AXIS2_PLACEMENT_3D ( 'NONE', #54644, #70419, #30110 ) ; +#77069 = VECTOR ( 'NONE', #96508, 1000.000000000000000 ) ; +#77070 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21757 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93499, #21572, #6677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77071 = CARTESIAN_POINT ( 'NONE', ( 1.363472769114729921, -1.331314275383060020, 0.8299999999999997380 ) ) ; +#77072 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41244 ), #65721 ) ; +#77073 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, -3.500000000000000444, 0.000000000000000000 ) ) ; +#77074 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77075 = ORIENTED_EDGE ( 'NONE', *, *, #22013, .T. ) ; +#77076 = CARTESIAN_POINT ( 'NONE', ( 0.4292069872566470767, -1.170408502478720081, 0.8100000000000000533 ) ) ; +#77077 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4600000000000000200, 0.2349999999999999867 ) ) ; +#77078 = VERTEX_POINT ( 'NONE', #81347 ) ; +#77079 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77080 = AXIS2_PLACEMENT_3D ( 'NONE', #1895, #41207, #62682 ) ; +#77081 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89611, 'distance_accuracy_value', 'NONE'); +#77082 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78756 ) ) ; +#77083 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77084 = SURFACE_SIDE_STYLE ('',( #55150 ) ) ; +#77085 = CARTESIAN_POINT ( 'NONE', ( 1.735855133396799976, -0.9683984092875530525, 0.8100000000000000533 ) ) ; +#77086 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77087 = SURFACE_SIDE_STYLE ('',( #14757 ) ) ; +#77088 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77089 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77090 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77091 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#77092 = FILL_AREA_STYLE_COLOUR ( '', #66768 ) ; +#77093 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77094 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#77095 = ADVANCED_FACE ( 'NONE', ( #27213 ), #79818, .T. ) ; +#77096 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77097 = SURFACE_SIDE_STYLE ('',( #92876 ) ) ; +#77098 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#77099 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32631, #24491, #55124, #31102 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#77100 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8090 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14172, #9389, #21884 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77102 = ADVANCED_FACE ( 'NONE', ( #63984 ), #64985, .T. ) ; +#77101 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65870, 'distance_accuracy_value', 'NONE'); +#77103 = ORIENTED_EDGE ( 'NONE', *, *, #28787, .T. ) ; +#77104 = CARTESIAN_POINT ( 'NONE', ( -0.9128876696368980470, 0.4958735128372510625, 0.8100000000000000533 ) ) ; +#77105 = SURFACE_SIDE_STYLE ('',( #100462 ) ) ; +#77106 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77107 = FILL_AREA_STYLE_COLOUR ( '', #19366 ) ; +#77108 = FACE_OUTER_BOUND ( 'NONE', #52693, .T. ) ; +#77109 = AXIS2_PLACEMENT_3D ( 'NONE', #54787, #7185, #15409 ) ; +#77110 = STYLED_ITEM ( 'NONE', ( #93162 ), #52504 ) ; +#77111 = FILL_AREA_STYLE_COLOUR ( '', #1900 ) ; +#77112 = AXIS2_PLACEMENT_3D ( 'NONE', #18768, #10520, #26471 ) ; +#77113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33111 ), #33345 ) ; +#77114 = EDGE_LOOP ( 'NONE', ( #38256, #17009, #20930, #9879 ) ) ; +#77115 = ADVANCED_FACE ( 'NONE', ( #88467 ), #87965, .T. ) ; +#77116 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77117 = VERTEX_POINT ( 'NONE', #51188 ) ; +#77118 = SURFACE_STYLE_FILL_AREA ( #14787 ) ; +#77119 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.000000000000000000 ) ) ; +#77120 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#77121 = CARTESIAN_POINT ( 'NONE', ( 1.167783407730830225, -0.8848889651143551083, 0.8100000000000620037 ) ) ; +#77122 = CARTESIAN_POINT ( 'NONE', ( -0.2277176615892120282, -1.378252124432310044, 0.8299999999999995159 ) ) ; +#77123 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77124 = STYLED_ITEM ( 'NONE', ( #66175 ), #19451 ) ; +#77125 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77126 = FILL_AREA_STYLE_COLOUR ( '', #57670 ) ; +#77127 = EDGE_LOOP ( 'NONE', ( #16043, #32618, #13764, #20388 ) ) ; +#77128 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77129 = LINE ( 'NONE', #38347, #36309 ) ; +#77130 = ORIENTED_EDGE ( 'NONE', *, *, #70227, .T. ) ; +#77131 = LINE ( 'NONE', #54166, #159 ) ; +#77132 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11812 ), #86993 ) ; +#77133 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77134 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77135 = ORIENTED_EDGE ( 'NONE', *, *, #31658, .T. ) ; +#77136 = STYLED_ITEM ( 'NONE', ( #74069 ), #60533 ) ; +#77137 = SURFACE_STYLE_USAGE ( .BOTH. , #54170 ) ; +#77138 = LINE ( 'NONE', #47001, #57756 ) ; +#77139 = CYLINDRICAL_SURFACE ( 'NONE', #38138, 0.3000000000000000444 ) ; +#77140 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77141 = DIRECTION ( 'NONE', ( 0.7071075504167436687, 0.7071060119555145906, 0.000000000000000000 ) ) ; +#77142 = FILL_AREA_STYLE ('',( #70480 ) ) ; +#77143 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#77145 = ORIENTED_EDGE ( 'NONE', *, *, #82053, .F. ) ; +#77144 = ORIENTED_EDGE ( 'NONE', *, *, #94875, .F. ) ; +#77146 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #68100 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11661, #35285, #52586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77147 = ADVANCED_FACE ( 'NONE', ( #68481 ), #13281, .T. ) ; +#77148 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77149 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2761799387799140360, 0.000000000000000000 ) ) ; +#77150 = EDGE_LOOP ( 'NONE', ( #24669, #68479, #28329, #45711 ) ) ; +#77151 = CARTESIAN_POINT ( 'NONE', ( -0.4444315888559909888, -1.066522886050349950, 0.8299999999999999600 ) ) ; +#77152 = EDGE_LOOP ( 'NONE', ( #66011, #45971, #99028, #32800 ) ) ; +#77153 = ADVANCED_FACE ( 'NONE', ( #44486 ), #99043, .T. ) ; +#77154 = EDGE_LOOP ( 'NONE', ( #61293, #86391, #13158, #36174 ) ) ; +#77155 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.000000000000000000 ) ) ; +#77156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77157 = PRESENTATION_STYLE_ASSIGNMENT (( #68968 ) ) ; +#77158 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77159 = SURFACE_SIDE_STYLE ('',( #99048 ) ) ; +#77160 = SURFACE_SIDE_STYLE ('',( #86335 ) ) ; +#77161 = ORIENTED_EDGE ( 'NONE', *, *, #23199, .T. ) ; +#77162 = VERTEX_POINT ( 'NONE', #31701 ) ; +#77163 = ORIENTED_EDGE ( 'NONE', *, *, #1464, .T. ) ; +#77164 = FILL_AREA_STYLE_COLOUR ( '', #14970 ) ; +#77165 = STYLED_ITEM ( 'NONE', ( #11438 ), #71078 ) ; +#77167 = EDGE_LOOP ( 'NONE', ( #564, #52986, #99304, #29190, #11009, #17793, #30416, #67986 ) ) ; +#77166 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#77168 = EDGE_CURVE ( 'NONE', #56225, #21700, #15337, .T. ) ; +#77169 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#77170 = LINE ( 'NONE', #14342, #48905 ) ; +#77171 = AXIS2_PLACEMENT_3D ( 'NONE', #33987, #3811, #35495 ) ; +#77172 = ORIENTED_EDGE ( 'NONE', *, *, #95659, .F. ) ; +#77173 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.4600000000000000200, 1.250000000000000000 ) ) ; +#77174 = ORIENTED_EDGE ( 'NONE', *, *, #36628, .T. ) ; +#77175 = CARTESIAN_POINT ( 'NONE', ( -0.07453434150941770642, -0.9021709523542820186, 0.8299999999999988498 ) ) ; +#77176 = EDGE_CURVE ( 'NONE', #14055, #89125, #68966, .T. ) ; +#77177 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77178 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82103 ) ) ; +#77179 = ORIENTED_EDGE ( 'NONE', *, *, #16396, .T. ) ; +#77180 = EDGE_CURVE ( 'NONE', #99316, #98364, #30175, .T. ) ; +#77182 = CARTESIAN_POINT ( 'NONE', ( 1.578229014142009889, -1.479722134560319979, 0.8299999999999999600 ) ) ; +#77181 = SURFACE_SIDE_STYLE ('',( #84355 ) ) ; +#77183 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77184 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.000000000000000000 ) ) ; +#77185 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77186 = VERTEX_POINT ( 'NONE', #53685 ) ; +#77187 = SURFACE_STYLE_USAGE ( .BOTH. , #70029 ) ; +#77188 = FILL_AREA_STYLE_COLOUR ( '', #20590 ) ; +#77189 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77190 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72733 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15031, #62083, #85528 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77193 = CARTESIAN_POINT ( 'NONE', ( 1.329231245976205011, -1.413524840751619882, 0.8099999999997299360 ) ) ; +#77192 = PRESENTATION_STYLE_ASSIGNMENT (( #53725 ) ) ; +#77194 = STYLED_ITEM ( 'NONE', ( #881 ), #21283 ) ; +#77195 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37949 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29684, #53189, #45470 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77196 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77197 = STYLED_ITEM ( 'NONE', ( #88659 ), #35317 ) ; +#77198 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -1.100000000000000089, 1.747825839084689943E-76 ) ) ; +#77199 = ORIENTED_EDGE ( 'NONE', *, *, #13135, .F. ) ; +#77200 = STYLED_ITEM ( 'NONE', ( #89756 ), #60792 ) ; +#77201 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.383333333333333304, 0.000000000000000000 ) ) ; +#77203 = AXIS2_PLACEMENT_3D ( 'NONE', #53038, #5991, #98897 ) ; +#77202 = FILL_AREA_STYLE ('',( #95020 ) ) ; +#77204 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64194 ), #62523 ) ; +#77205 = ORIENTED_EDGE ( 'NONE', *, *, #97463, .F. ) ; +#77206 = SURFACE_SIDE_STYLE ('',( #92509 ) ) ; +#77208 = FILL_AREA_STYLE ('',( #99598 ) ) ; +#77207 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 6.539920000000000400, 0.8648700000000000276 ) ) ; +#77209 = FILL_AREA_STYLE ('',( #15912 ) ) ; +#77210 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78829 ) ) ; +#77211 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 2.300000000000000266, 0.000000000000000000 ) ) ; +#77212 = VECTOR ( 'NONE', #3363, 1000.000000000000000 ) ; +#77213 = DIRECTION ( 'NONE', ( -0.7071067811865504593, -0.7071067811865445751, 0.000000000000000000 ) ) ; +#77214 = ADVANCED_FACE ( 'NONE', ( #61379 ), #22533, .T. ) ; +#77215 = ORIENTED_EDGE ( 'NONE', *, *, #14642, .F. ) ; +#77216 = SURFACE_SIDE_STYLE ('',( #17437 ) ) ; +#77217 = SURFACE_STYLE_FILL_AREA ( #71085 ) ; +#77218 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77219 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999906, 0.8648700000000000276 ) ) ; +#77220 = LINE ( 'NONE', #54266, #55139 ) ; +#77221 = LINE ( 'NONE', #47604, #87341 ) ; +#77222 = AXIS2_PLACEMENT_3D ( 'NONE', #8246, #39464, #39982 ) ; +#77223 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77224 = FACE_OUTER_BOUND ( 'NONE', #75659, .T. ) ; +#77225 = SURFACE_STYLE_FILL_AREA ( #22614 ) ; +#77226 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#77227 = ORIENTED_EDGE ( 'NONE', *, *, #77464, .F. ) ; +#77228 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77229 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77230 = ORIENTED_EDGE ( 'NONE', *, *, #45818, .F. ) ; +#77231 = FACE_OUTER_BOUND ( 'NONE', #3642, .T. ) ; +#77232 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#77233 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77234 = SURFACE_STYLE_FILL_AREA ( #61456 ) ; +#77235 = SURFACE_STYLE_FILL_AREA ( #5755 ) ; +#77236 = FILL_AREA_STYLE ('',( #30257 ) ) ; +#77237 = PLANE ( 'NONE', #78621 ) ; +#77238 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#77239 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77240 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#77241 = ORIENTED_EDGE ( 'NONE', *, *, #90707, .T. ) ; +#77242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77244 = EDGE_CURVE ( 'NONE', #71910, #99336, #14323, .T. ) ; +#77243 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#77245 = FILL_AREA_STYLE_COLOUR ( '', #24827 ) ; +#77246 = ORIENTED_EDGE ( 'NONE', *, *, #4634, .F. ) ; +#77247 = AXIS2_PLACEMENT_3D ( 'NONE', #10828, #97153, #88019 ) ; +#77248 = ORIENTED_EDGE ( 'NONE', *, *, #52897, .T. ) ; +#77249 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77250 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77251 = AXIS2_PLACEMENT_3D ( 'NONE', #99022, #60852, #6131 ) ; +#77252 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8648700000000000276 ) ) ; +#77253 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#77254 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#77255 = VECTOR ( 'NONE', #76832, 1000.000000000000000 ) ; +#77256 = ORIENTED_EDGE ( 'NONE', *, *, #68528, .T. ) ; +#77257 = SURFACE_STYLE_USAGE ( .BOTH. , #60480 ) ; +#77258 = SURFACE_STYLE_FILL_AREA ( #86961 ) ; +#77259 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77260 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56135 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45304, #29016, #13618 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77261 = EDGE_CURVE ( 'NONE', #38857, #36985, #46498, .T. ) ; +#77262 = ORIENTED_EDGE ( 'NONE', *, *, #9716, .T. ) ; +#77264 = CIRCLE ( 'NONE', #44601, 0.1000000000000000194 ) ; +#77263 = VECTOR ( 'NONE', #61121, 1000.000000000000000 ) ; +#77265 = FILL_AREA_STYLE_COLOUR ( '', #5689 ) ; +#77266 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77267 = LINE ( 'NONE', #82944, #8605 ) ; +#77268 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#77269 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -0.7666666666666686059, 0.000000000000000000 ) ) ; +#77270 = EDGE_LOOP ( 'NONE', ( #92827, #22846, #7253, #51455 ) ) ; +#77271 = EDGE_LOOP ( 'NONE', ( #67978, #41618, #81453, #9656 ) ) ; +#77272 = SURFACE_SIDE_STYLE ('',( #60980 ) ) ; +#77273 = ORIENTED_EDGE ( 'NONE', *, *, #74363, .F. ) ; +#77274 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31528 ), #2323 ) ; +#77275 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72701, 'distance_accuracy_value', 'NONE'); +#77276 = VECTOR ( 'NONE', #45352, 1000.000000000000000 ) ; +#77277 = VERTEX_POINT ( 'NONE', #71017 ) ; +#77279 = ORIENTED_EDGE ( 'NONE', *, *, #89315, .T. ) ; +#77278 = LINE ( 'NONE', #16477, #11688 ) ; +#77280 = EDGE_CURVE ( 'NONE', #88653, #24985, #64262, .T. ) ; +#77281 = FACE_OUTER_BOUND ( 'NONE', #14843, .T. ) ; +#77283 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77282 = LINE ( 'NONE', #99185, #31383 ) ; +#77284 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#77285 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77286 = STYLED_ITEM ( 'NONE', ( #14823 ), #68412 ) ; +#77287 = ORIENTED_EDGE ( 'NONE', *, *, #22772, .T. ) ; +#77288 = PLANE ( 'NONE', #94410 ) ; +#77289 = FILL_AREA_STYLE ('',( #83468 ) ) ; +#77290 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, 0.000000000000000000 ) ) ; +#77291 = ORIENTED_EDGE ( 'NONE', *, *, #40872, .T. ) ; +#77292 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.022832238033761717E-16, 0.000000000000000000 ) ) ; +#77293 = DIRECTION ( 'NONE', ( 0.3643423458302799123, 0.000000000000000000, 0.9312650831180607769 ) ) ; +#77294 = FACE_OUTER_BOUND ( 'NONE', #25151, .T. ) ; +#77295 = PRESENTATION_STYLE_ASSIGNMENT (( #62516 ) ) ; +#77296 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64275 ), #44632 ) ; +#77297 = ORIENTED_EDGE ( 'NONE', *, *, #69864, .F. ) ; +#77299 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.000000000000000000, 0.2999999999999999889 ) ) ; +#77298 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#77300 = EDGE_LOOP ( 'NONE', ( #65090, #55603, #66970, #100751 ) ) ; +#77301 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#77302 = EDGE_CURVE ( 'NONE', #10747, #98905, #78179, .T. ) ; +#77303 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77304 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77305 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77306 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77307 = ORIENTED_EDGE ( 'NONE', *, *, #2599, .T. ) ; +#77308 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#77309 = VECTOR ( 'NONE', #96472, 1000.000000000000000 ) ; +#77310 = ORIENTED_EDGE ( 'NONE', *, *, #46834, .F. ) ; +#77311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77312 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.123820061220055511, -0.02000000000000000042 ) ) ; +#77313 = CIRCLE ( 'NONE', #30005, 0.009999999999999998473 ) ; +#77314 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57777 ) ) ; +#77315 = PLANE ( 'NONE', #16563 ) ; +#77316 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77317 = FILL_AREA_STYLE_COLOUR ( '', #23401 ) ; +#77318 = SURFACE_SIDE_STYLE ('',( #51866 ) ) ; +#77319 = ORIENTED_EDGE ( 'NONE', *, *, #53336, .F. ) ; +#77320 = FILL_AREA_STYLE_COLOUR ( '', #66078 ) ; +#77321 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33342 ) ) ; +#77322 = AXIS2_PLACEMENT_3D ( 'NONE', #28541, #97927, #13136 ) ; +#77324 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77323 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, -3.383333333333323090, 0.000000000000000000 ) ) ; +#77325 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75233, 'distance_accuracy_value', 'NONE'); +#77326 = SURFACE_STYLE_USAGE ( .BOTH. , #6801 ) ; +#77327 = FILL_AREA_STYLE ('',( #94658 ) ) ; +#77328 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77329 = LINE ( 'NONE', #15525, #13330 ) ; +#77330 = STYLED_ITEM ( 'NONE', ( #84881 ), #21636 ) ; +#77331 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77332 = ORIENTED_EDGE ( 'NONE', *, *, #94451, .F. ) ; +#77333 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#77335 = AXIS2_PLACEMENT_3D ( 'NONE', #61925, #47078, #38428 ) ; +#77334 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77336 = CARTESIAN_POINT ( 'NONE', ( 0.005236623695644900336, -1.379727385542079965, 0.8299999999999999600 ) ) ; +#77337 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77338 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77339 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77340 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 2.258754526011470139E-17 ) ) ; +#77342 = CYLINDRICAL_SURFACE ( 'NONE', #37034, 0.05000000000000012768 ) ; +#77341 = AXIS2_PLACEMENT_3D ( 'NONE', #31134, #6574, #15261 ) ; +#77343 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77344 = LINE ( 'NONE', #69678, #46749 ) ; +#77345 = STYLED_ITEM ( 'NONE', ( #47511 ), #97630 ) ; +#77346 = SURFACE_SIDE_STYLE ('',( #85011 ) ) ; +#77347 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#77348 = SURFACE_SIDE_STYLE ('',( #100713 ) ) ; +#77349 = PRESENTATION_STYLE_ASSIGNMENT (( #31402 ) ) ; +#77350 = PLANE ( 'NONE', #27508 ) ; +#77351 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000000, -0.02000000000000000042 ) ) ; +#77352 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77353 = FILL_AREA_STYLE ('',( #54925 ) ) ; +#77354 = AXIS2_PLACEMENT_3D ( 'NONE', #48077, #9181, #95001 ) ; +#77355 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77356 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#77357 = AXIS2_PLACEMENT_3D ( 'NONE', #19403, #66864, #28569 ) ; +#77358 = LINE ( 'NONE', #38572, #43842 ) ; +#77359 = SURFACE_SIDE_STYLE ('',( #46193 ) ) ; +#77360 = ORIENTED_EDGE ( 'NONE', *, *, #74287, .T. ) ; +#77361 = CARTESIAN_POINT ( 'NONE', ( -0.01270902371792639873, -0.9143971421076433348, 0.8100000000003740874 ) ) ; +#77362 = FACE_OUTER_BOUND ( 'NONE', #68959, .T. ) ; +#77363 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49640 ), #43126 ) ; +#77364 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.1000000000000016015, 0.000000000000000000 ) ) ; +#77365 = VERTEX_POINT ( 'NONE', #43 ) ; +#77366 = AXIS2_PLACEMENT_3D ( 'NONE', #29821, #193, #77293 ) ; +#77367 = EDGE_CURVE ( 'NONE', #89974, #20528, #77665, .T. ) ; +#77368 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#77369 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.100000000000000089, 1.048695503451053346E-76 ) ) ; +#77370 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.099999999999999867, 4.486444673467788097E-79 ) ) ; +#77371 = FACE_OUTER_BOUND ( 'NONE', #7118, .T. ) ; +#77372 = VECTOR ( 'NONE', #96276, 1000.000000000000000 ) ; +#77373 = SURFACE_SIDE_STYLE ('',( #65853 ) ) ; +#77374 = EDGE_LOOP ( 'NONE', ( #100919, #7629, #54859, #76897 ) ) ; +#77375 = SURFACE_STYLE_USAGE ( .BOTH. , #52419 ) ; +#77376 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77377 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4566, 'distance_accuracy_value', 'NONE'); +#77378 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77379 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21642 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28153, #14268, #61322 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77380 = AXIS2_PLACEMENT_3D ( 'NONE', #62916, #43428, #96017 ) ; +#77381 = PLANE ( 'NONE', #32309 ) ; +#77382 = EDGE_CURVE ( 'NONE', #13680, #94722, #2505, .T. ) ; +#77383 = ORIENTED_EDGE ( 'NONE', *, *, #24828, .F. ) ; +#77384 = ORIENTED_EDGE ( 'NONE', *, *, #81125, .F. ) ; +#77385 = EDGE_CURVE ( 'NONE', #41748, #66177, #23055, .T. ) ; +#77386 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77387 = FACE_OUTER_BOUND ( 'NONE', #54249, .T. ) ; +#77388 = EDGE_LOOP ( 'NONE', ( #73872, #15041, #31666, #88688 ) ) ; +#77389 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77390 = CARTESIAN_POINT ( 'NONE', ( -0.07152490633971099465, -1.505252428432260148, 0.8100000000000000533 ) ) ; +#77391 = VECTOR ( 'NONE', #34103, 1000.000000000000000 ) ; +#77392 = STYLED_ITEM ( 'NONE', ( #92484 ), #26831 ) ; +#77393 = SURFACE_STYLE_USAGE ( .BOTH. , #76906 ) ; +#77394 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77395 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77396 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #26106, #42910 ), + ( #26607, #57774 ), + ( #50103, #74056 ), + ( #4106, #19928 ), + ( #4590, #81244 ), + ( #80231, #41422 ), + ( #66885, #97965 ), + ( #28109, #59284 ), + ( #20418, #72537 ), + ( #95996, #53593 ), + ( #21429, #6043 ), + ( #68865, #14731 ), + ( #5074, #76546 ), + ( #52594, #83733 ), + ( #6546, #84227 ), + ( #36274, #30561 ), + ( #52099, #44385 ), + ( #99447, #45871 ), + ( #75558, #77057 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06972848522764360513, 0.1371566764511960024, 0.2028565572390650107, 0.2668931989899159807, 0.3293761293060850082, 0.3894310858417550092, 0.4479802515295520093, 0.5057883253526750389, 0.5636564595284360157, 0.6208711770372169481, 0.6795632605569840168, 0.7390300992722009799, 0.8005340725457850137, 0.8637937833762510120, 0.9302451451948829941, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#77397 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #22210, #38492 ) ; +#77398 = SURFACE_SIDE_STYLE ('',( #39111 ) ) ; +#77399 = ORIENTED_EDGE ( 'NONE', *, *, #56563, .F. ) ; +#77400 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30162 ), #98532 ) ; +#77401 = ORIENTED_EDGE ( 'NONE', *, *, #42689, .F. ) ; +#77402 = EDGE_CURVE ( 'NONE', #83432, #839, #7622, .T. ) ; +#77403 = VECTOR ( 'NONE', #63681, 1000.000000000000000 ) ; +#77405 = STYLED_ITEM ( 'NONE', ( #73256 ), #20286 ) ; +#77404 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69697, 'distance_accuracy_value', 'NONE'); +#77406 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999999237, 0.1399999999999999856 ) ) ; +#77408 = LINE ( 'NONE', #7386, #26953 ) ; +#77407 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77409 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77410 = ORIENTED_EDGE ( 'NONE', *, *, #44083, .F. ) ; +#77411 = FILL_AREA_STYLE_COLOUR ( '', #92112 ) ; +#77412 = LINE ( 'NONE', #83594, #83254 ) ; +#77413 = VECTOR ( 'NONE', #1190, 1000.000000000000000 ) ; +#77414 = FACE_OUTER_BOUND ( 'NONE', #62741, .T. ) ; +#77415 = SURFACE_STYLE_FILL_AREA ( #99780 ) ; +#77416 = ORIENTED_EDGE ( 'NONE', *, *, #11432, .F. ) ; +#77417 = FILL_AREA_STYLE ('',( #83599 ) ) ; +#77418 = ORIENTED_EDGE ( 'NONE', *, *, #77579, .T. ) ; +#77419 = VERTEX_POINT ( 'NONE', #32222 ) ; +#77420 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86271 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81551, #26398, #3411 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77421 = EDGE_CURVE ( 'NONE', #43651, #47027, #63394, .T. ) ; +#77422 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886600000000008, 0.8648700000000000276 ) ) ; +#77423 = LINE ( 'NONE', #93712, #86487 ) ; +#77424 = EDGE_CURVE ( 'NONE', #47262, #35923, #12242, .T. ) ; +#77425 = LINE ( 'NONE', #93713, #3334 ) ; +#77426 = VERTEX_POINT ( 'NONE', #88351 ) ; +#77427 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#77428 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77429 = ORIENTED_EDGE ( 'NONE', *, *, #77978, .T. ) ; +#77430 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#77431 = SURFACE_STYLE_FILL_AREA ( #99797 ) ; +#77432 = ORIENTED_EDGE ( 'NONE', *, *, #100129, .T. ) ; +#77433 = ORIENTED_EDGE ( 'NONE', *, *, #18859, .T. ) ; +#77434 = PRESENTATION_STYLE_ASSIGNMENT (( #30980 ) ) ; +#77436 = PLANE ( 'NONE', #57214 ) ; +#77435 = CARTESIAN_POINT ( 'NONE', ( 1.001160189360249975, -1.432289833627879982, 0.8100000000000000533 ) ) ; +#77437 = PLANE ( 'NONE', #97178 ) ; +#77438 = VECTOR ( 'NONE', #13935, 1000.000000000000000 ) ; +#77439 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#77440 = VECTOR ( 'NONE', #41925, 1000.000000000000000 ) ; +#77441 = SURFACE_SIDE_STYLE ('',( #23345 ) ) ; +#77442 = SURFACE_SIDE_STYLE ('',( #92259 ) ) ; +#77443 = ORIENTED_EDGE ( 'NONE', *, *, #20215, .T. ) ; +#77444 = EDGE_CURVE ( 'NONE', #93449, #44826, #18379, .T. ) ; +#77446 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36807 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15489, #30834, #6288 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77445 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77447 = EDGE_LOOP ( 'NONE', ( #76010, #89110, #25861, #9010 ) ) ; +#77448 = VECTOR ( 'NONE', #84815, 1000.000000000000000 ) ; +#77449 = PLANE ( 'NONE', #61243 ) ; +#77450 = CARTESIAN_POINT ( 'NONE', ( 1.084944975536529910, -1.110638925478639960, 0.8299999999999999600 ) ) ; +#77451 = SURFACE_SIDE_STYLE ('',( #78979 ) ) ; +#77453 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#77452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77454 = SURFACE_SIDE_STYLE ('',( #6928 ) ) ; +#77455 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#77456 = PLANE ( 'NONE', #6851 ) ; +#77457 = ADVANCED_FACE ( 'NONE', ( #2586 ), #73033, .T. ) ; +#77458 = ORIENTED_EDGE ( 'NONE', *, *, #35019, .F. ) ; +#77459 = SURFACE_STYLE_USAGE ( .BOTH. , #13097 ) ; +#77460 = CIRCLE ( 'NONE', #4086, 0.009999999999999998473 ) ; +#77461 = FILL_AREA_STYLE_COLOUR ( '', #5389 ) ; +#77462 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77463 = PLANE ( 'NONE', #30109 ) ; +#77464 = EDGE_CURVE ( 'NONE', #88079, #82873, #18886, .T. ) ; +#77465 = CIRCLE ( 'NONE', #56310, 0.1100000000000007222 ) ; +#77466 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47713 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11673, #73062, #66401 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77467 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77469 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#77470 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77471 = CARTESIAN_POINT ( 'NONE', ( 7.739619254069480370, 10.45022074593052253, 0.8991599999999999593 ) ) ; +#77472 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109697000000000600, 0.8991599999999999593 ) ) ; +#77473 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77474 = EDGE_CURVE ( 'NONE', #29189, #75434, #55720, .T. ) ; +#77475 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77476 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#77477 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77478 = STYLED_ITEM ( 'NONE', ( #66451 ), #20685 ) ; +#77479 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77480 = LINE ( 'NONE', #76983, #42031 ) ; +#77481 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77482 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77483 = ORIENTED_EDGE ( 'NONE', *, *, #93471, .F. ) ; +#77484 = PRESENTATION_STYLE_ASSIGNMENT (( #60209 ) ) ; +#77485 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#77486 = PRESENTATION_STYLE_ASSIGNMENT (( #62210 ) ) ; +#77487 = SURFACE_STYLE_USAGE ( .BOTH. , #47363 ) ; +#77489 = VECTOR ( 'NONE', #95248, 1000.000000000000000 ) ; +#77488 = STYLED_ITEM ( 'NONE', ( #1080 ), #38874 ) ; +#77490 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69368 ) ) ; +#77491 = FILL_AREA_STYLE ('',( #47364 ) ) ; +#77492 = LINE ( 'NONE', #46324, #41055 ) ; +#77493 = SURFACE_STYLE_FILL_AREA ( #92777 ) ; +#77494 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#77495 = EDGE_CURVE ( 'NONE', #9046, #57617, #32734, .T. ) ; +#77496 = VECTOR ( 'NONE', #75204, 1000.000000000000000 ) ; +#77497 = EDGE_CURVE ( 'NONE', #98144, #93204, #41898, .T. ) ; +#77498 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20431 ), #5671 ) ; +#77499 = LINE ( 'NONE', #7472, #61357 ) ; +#77500 = ORIENTED_EDGE ( 'NONE', *, *, #9264, .F. ) ; +#77501 = LINE ( 'NONE', #94815, #22696 ) ; +#77502 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77503 = CARTESIAN_POINT ( 'NONE', ( 1.809085324296979991, -1.273483528256009967, 0.8299999999999994049 ) ) ; +#77504 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77505 = ADVANCED_FACE ( 'NONE', ( #17878 ), #79185, .F. ) ; +#77506 = VERTEX_POINT ( 'NONE', #72034 ) ; +#77507 = ORIENTED_EDGE ( 'NONE', *, *, #10720, .T. ) ; +#77508 = EDGE_CURVE ( 'NONE', #80592, #54862, #80212, .T. ) ; +#77509 = AXIS2_PLACEMENT_3D ( 'NONE', #13282, #43500, #82824 ) ; +#77510 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77511 = ORIENTED_EDGE ( 'NONE', *, *, #58629, .T. ) ; +#77512 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77513 = SURFACE_STYLE_USAGE ( .BOTH. , #63248 ) ; +#77514 = LINE ( 'NONE', #38724, #72447 ) ; +#77515 = PRODUCT_CONTEXT ( 'NONE', #61313, 'mechanical' ) ; +#77516 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77517 = LINE ( 'NONE', #30524, #89773 ) ; +#77518 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77520 = EDGE_LOOP ( 'NONE', ( #6512, #87109, #74873, #13534, #35469, #13897 ) ) ; +#77519 = EDGE_LOOP ( 'NONE', ( #80578, #87336, #5653, #33383 ) ) ; +#77521 = VERTEX_POINT ( 'NONE', #63877 ) ; +#77522 = PLANE ( 'NONE', #91486 ) ; +#77523 = EDGE_CURVE ( 'NONE', #78634, #94145, #2091, .T. ) ; +#77524 = VECTOR ( 'NONE', #37649, 1000.000000000000000 ) ; +#77525 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81805, #57320, #49654 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77526 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63335, 'distance_accuracy_value', 'NONE'); +#77527 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77528 = FACE_OUTER_BOUND ( 'NONE', #85540, .T. ) ; +#77529 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77530 = ORIENTED_EDGE ( 'NONE', *, *, #11384, .T. ) ; +#77532 = ORIENTED_EDGE ( 'NONE', *, *, #57633, .T. ) ; +#77531 = VECTOR ( 'NONE', #10897, 1000.000000000000000 ) ; +#77533 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#77534 = EDGE_CURVE ( 'NONE', #84842, #66746, #25094, .T. ) ; +#77535 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#77536 = AXIS2_PLACEMENT_3D ( 'NONE', #76408, #93199, #53948 ) ; +#77537 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10370 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20586, #14393, #53256 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77538 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8648700000000000276 ) ) ; +#77540 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#77539 = SURFACE_SIDE_STYLE ('',( #62752 ) ) ; +#77541 = ORIENTED_EDGE ( 'NONE', *, *, #45106, .T. ) ; +#77542 = VECTOR ( 'NONE', #444, 999.9999999999998863 ) ; +#77543 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1555, #62844, #39846 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77544 = ORIENTED_EDGE ( 'NONE', *, *, #68197, .F. ) ; +#77545 = ORIENTED_EDGE ( 'NONE', *, *, #45085, .T. ) ; +#77546 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#77547 = ADVANCED_FACE ( 'NONE', ( #79708 ), #9648, .F. ) ; +#77548 = VECTOR ( 'NONE', #37862, 1000.000000000000000 ) ; +#77549 = FACE_OUTER_BOUND ( 'NONE', #4635, .T. ) ; +#77550 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, -3.500000000000000444, 0.000000000000000000 ) ) ; +#77551 = EDGE_CURVE ( 'NONE', #91322, #64466, #5055, .T. ) ; +#77552 = MANIFOLD_SOLID_BREP ( 'ÊäÈë167', #9411 ) ; +#77554 = ORIENTED_EDGE ( 'NONE', *, *, #28841, .F. ) ; +#77553 = SURFACE_SIDE_STYLE ('',( #23441 ) ) ; +#77555 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77556 = STYLED_ITEM ( 'NONE', ( #63950 ), #20611 ) ; +#77557 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#77558 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77559 = ORIENTED_EDGE ( 'NONE', *, *, #88937, .T. ) ; +#77561 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 11.03497999999999912, 0.8648700000000000276 ) ) ; +#77560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70668 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41491, #50183, #89942 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77562 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77563 = ORIENTED_EDGE ( 'NONE', *, *, #67396, .T. ) ; +#77564 = ORIENTED_EDGE ( 'NONE', *, *, #14093, .F. ) ; +#77566 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77565 = FACE_OUTER_BOUND ( 'NONE', #45919, .T. ) ; +#77567 = SURFACE_STYLE_FILL_AREA ( #15235 ) ; +#77568 = STYLED_ITEM ( 'NONE', ( #70913 ), #39139 ) ; +#77569 = SURFACE_STYLE_USAGE ( .BOTH. , #92836 ) ; +#77570 = SURFACE_STYLE_FILL_AREA ( #87240 ) ; +#77571 = FILL_AREA_STYLE_COLOUR ( '', #39616 ) ; +#77572 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77573 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#77575 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#77574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6352, 'distance_accuracy_value', 'NONE'); +#77576 = VECTOR ( 'NONE', #67373, 1000.000000000000000 ) ; +#77577 = CARTESIAN_POINT ( 'NONE', ( 0.1720843054334539879, -1.066823530734400061, 0.8300000000000020695 ) ) ; +#77578 = ORIENTED_EDGE ( 'NONE', *, *, #85565, .F. ) ; +#77579 = EDGE_CURVE ( 'NONE', #11208, #85776, #4084, .T. ) ; +#77580 = CARTESIAN_POINT ( 'NONE', ( 0.05990737478736290339, -1.228633653069070020, 0.8100000000000000533 ) ) ; +#77581 = VERTEX_POINT ( 'NONE', #6025 ) ; +#77582 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77583 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#77584 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#77585 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56823 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #30518, #77512, #6504 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77586 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #28531, #59731, #83169, #13129 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#77588 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77587 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#77589 = CARTESIAN_POINT ( 'NONE', ( 1.762090253802699902, -0.9814610950457449690, 0.8299999999999999600 ) ) ; +#77590 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#77591 = ADVANCED_FACE ( 'NONE', ( #83211 ), #58746, .T. ) ; +#77592 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#77593 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77594 = FILL_AREA_STYLE ('',( #84747 ) ) ; +#77595 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.289444213855800265E-17, -0.8499999999999999778 ) ) ; +#77596 = EDGE_CURVE ( 'NONE', #85582, #97502, #54069, .T. ) ; +#77597 = STYLED_ITEM ( 'NONE', ( #47310 ), #73384 ) ; +#77598 = SURFACE_SIDE_STYLE ('',( #1519 ) ) ; +#77599 = SURFACE_STYLE_USAGE ( .BOTH. , #38313 ) ; +#77601 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 1.458578643762689975, -0.02000000000000000042 ) ) ; +#77600 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#77602 = EDGE_CURVE ( 'NONE', #7176, #82708, #76357, .T. ) ; +#77603 = PLANE ( 'NONE', #64804 ) ; +#77604 = CIRCLE ( 'NONE', #80849, 0.1999999999999996503 ) ; +#77605 = AXIS2_PLACEMENT_3D ( 'NONE', #56190, #32189, #85276 ) ; +#77606 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48273 ), #10690 ) ; +#77607 = ORIENTED_EDGE ( 'NONE', *, *, #66273, .T. ) ; +#77608 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77609 = PLANE ( 'NONE', #11254 ) ; +#77610 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15510, 'distance_accuracy_value', 'NONE'); +#77611 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88270, 'distance_accuracy_value', 'NONE'); +#77612 = PLANE ( 'NONE', #49376 ) ; +#77614 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92314 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41161, #64136, #87606 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77613 = LINE ( 'NONE', #7576, #69632 ) ; +#77615 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8100000000000001643 ) ) ; +#77616 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20546 ) ) ; +#77617 = SURFACE_SIDE_STYLE ('',( #23010 ) ) ; +#77618 = VECTOR ( 'NONE', #4066, 1000.000000000000000 ) ; +#77619 = FILL_AREA_STYLE_COLOUR ( '', #66061 ) ; +#77621 = ADVANCED_FACE ( 'NONE', ( #8003 ), #93818, .T. ) ; +#77620 = PRODUCT ( 'DFN1006.xtd', 'DFN1006.xtd', '', ( #10004 ) ) ; +#77622 = ADVANCED_FACE ( 'NONE', ( #91845 ), #14199, .T. ) ; +#77623 = VECTOR ( 'NONE', #20787, 1000.000000000000000 ) ; +#77624 = ORIENTED_EDGE ( 'NONE', *, *, #9937, .T. ) ; +#77625 = PRESENTATION_STYLE_ASSIGNMENT (( #45933 ) ) ; +#77626 = ORIENTED_EDGE ( 'NONE', *, *, #3378, .F. ) ; +#77627 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20555 ), #71076 ) ; +#77628 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#77629 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10359, 'distance_accuracy_value', 'NONE'); +#77630 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6332, 'distance_accuracy_value', 'NONE'); +#77631 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77632 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77633 = PLANE ( 'NONE', #61954 ) ; +#77634 = STYLED_ITEM ( 'NONE', ( #35228 ), #15800 ) ; +#77635 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.000000000000000000, 0.2400000000000000189 ) ) ; +#77636 = FILL_AREA_STYLE ('',( #1556 ) ) ; +#77637 = PRESENTATION_STYLE_ASSIGNMENT (( #15304 ) ) ; +#77638 = ORIENTED_EDGE ( 'NONE', *, *, #59825, .T. ) ; +#77639 = LINE ( 'NONE', #71497, #25619 ) ; +#77641 = STYLED_ITEM ( 'NONE', ( #57681 ), #39541 ) ; +#77640 = FACE_OUTER_BOUND ( 'NONE', #31650, .T. ) ; +#77642 = ORIENTED_EDGE ( 'NONE', *, *, #66013, .T. ) ; +#77643 = EDGE_CURVE ( 'NONE', #50104, #44974, #7505, .T. ) ; +#77644 = VECTOR ( 'NONE', #16567, 1000.000000000000000 ) ; +#77645 = SURFACE_SIDE_STYLE ('',( #48542 ) ) ; +#77646 = VERTEX_POINT ( 'NONE', #62249 ) ; +#77647 = EDGE_CURVE ( 'NONE', #44609, #45252, #53232, .T. ) ; +#77648 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20888 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44331, #5505, #74514 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77649 = CARTESIAN_POINT ( 'NONE', ( 1.067938486522060026, -1.390907012919420094, 0.8100000000000000533 ) ) ; +#77650 = LINE ( 'NONE', #62351, #18554 ) ; +#77651 = STYLED_ITEM ( 'NONE', ( #73795 ), #14068 ) ; +#77652 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#77653 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77654 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#77656 = ORIENTED_EDGE ( 'NONE', *, *, #78235, .T. ) ; +#77655 = ORIENTED_EDGE ( 'NONE', *, *, #40046, .F. ) ; +#77657 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#77658 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.100000000000000089, -0.02000000000000000042 ) ) ; +#77659 = ORIENTED_EDGE ( 'NONE', *, *, #11868, .F. ) ; +#77660 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77662 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8299999999999999600 ) ) ; +#77661 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77663 = VERTEX_POINT ( 'NONE', #93326 ) ; +#77664 = ORIENTED_EDGE ( 'NONE', *, *, #69646, .T. ) ; +#77665 = LINE ( 'NONE', #38869, #886 ) ; +#77666 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77667 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77668 = CARTESIAN_POINT ( 'NONE', ( 8.199238872965260327, 10.59871312703474011, 0.8991599999999999593 ) ) ; +#77669 = EDGE_LOOP ( 'NONE', ( #92214, #72553, #86691, #74913 ) ) ; +#77671 = EDGE_LOOP ( 'NONE', ( #44570, #39985, #76385, #38730, #67615, #92792 ) ) ; +#77670 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52408 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53722, #45024, #54761 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77672 = EDGE_LOOP ( 'NONE', ( #50643, #22915, #14831, #98708, #32874, #1955, #84090, #51135 ) ) ; +#77673 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999999556, 3.123820061220045297, 0.000000000000000000 ) ) ; +#77674 = EDGE_CURVE ( 'NONE', #47399, #79941, #48446, .T. ) ; +#77676 = VERTEX_POINT ( 'NONE', #70899 ) ; +#77675 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#77677 = CIRCLE ( 'NONE', #17317, 0.09999999999999939493 ) ; +#77678 = VECTOR ( 'NONE', #12341, 1000.000000000000000 ) ; +#77679 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, 0.09999999999999939493, 0.1829999999999749882 ) ) ; +#77680 = VERTEX_POINT ( 'NONE', #32098 ) ; +#77681 = ADVANCED_FACE ( 'NONE', ( #94843 ), #48938, .T. ) ; +#77682 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77683 = ORIENTED_EDGE ( 'NONE', *, *, #38606, .F. ) ; +#77684 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56525 ), #27210 ) ; +#77685 = CARTESIAN_POINT ( 'NONE', ( -2.699999999999999734, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#77686 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4420 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31847, #55376, #96632 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77687 = CARTESIAN_POINT ( 'NONE', ( -0.8380936289687549445, 0.5753100270687899753, 0.8100000000000000533 ) ) ; +#77688 = AXIS2_PLACEMENT_3D ( 'NONE', #18020, #32380, #24751 ) ; +#77689 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -6.776263578034399754E-16 ) ) ; +#77690 = ORIENTED_EDGE ( 'NONE', *, *, #43002, .F. ) ; +#77691 = CARTESIAN_POINT ( 'NONE', ( 1.205401789321949968, -0.8845642871695170717, 0.8299999999999998490 ) ) ; +#77694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77693 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77692 = AXIS2_PLACEMENT_3D ( 'NONE', #48429, #91219, #42751 ) ; +#77695 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.9000000000000003553, -0.02000000000001884992 ) ) ; +#77696 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#77697 = SURFACE_SIDE_STYLE ('',( #31739 ) ) ; +#77698 = ADVANCED_FACE ( 'NONE', ( #2467 ), #41776, .T. ) ; +#77699 = AXIS2_PLACEMENT_3D ( 'NONE', #23876, #99825, #30467 ) ; +#77700 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.000000000000000000, -13.25000000000000000 ) ) ; +#77701 = ORIENTED_EDGE ( 'NONE', *, *, #54529, .T. ) ; +#77702 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77703 = FILL_AREA_STYLE ('',( #85352 ) ) ; +#77704 = FILL_AREA_STYLE_COLOUR ( '', #61309 ) ; +#77705 = AXIS2_PLACEMENT_3D ( 'NONE', #67790, #20849, #82160 ) ; +#77706 = DIRECTION ( 'NONE', ( 0.5479224129540708477, 0.8365291563254616536, 0.000000000000000000 ) ) ; +#77707 = PRESENTATION_STYLE_ASSIGNMENT (( #84362 ) ) ; +#77709 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#77708 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#77710 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#77711 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77712 = SURFACE_STYLE_USAGE ( .BOTH. , #39401 ) ; +#77713 = VECTOR ( 'NONE', #34470, 1000.000000000000000 ) ; +#77714 = ORIENTED_EDGE ( 'NONE', *, *, #57611, .F. ) ; +#77715 = AXIS2_PLACEMENT_3D ( 'NONE', #52414, #74385, #59610 ) ; +#77716 = FILL_AREA_STYLE ('',( #6680 ) ) ; +#77717 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97567 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77682, #46519, #29221 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#77718 = ORIENTED_EDGE ( 'NONE', *, *, #88349, .T. ) ; +#77719 = FILL_AREA_STYLE ('',( #62937 ) ) ; +#77720 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#77721 = PLANE ( 'NONE', #42362 ) ; +#77722 = MANIFOLD_SOLID_BREP ( 'ÊäÈë74', #59830 ) ; +#77723 = EDGE_CURVE ( 'NONE', #63778, #84082, #34632, .T. ) ; +#77724 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85820 ) ) ; +#77725 = PRESENTATION_STYLE_ASSIGNMENT (( #22598 ) ) ; +#77726 = EDGE_CURVE ( 'NONE', #61237, #64307, #32608, .T. ) ; +#77727 = ORIENTED_EDGE ( 'NONE', *, *, #71303, .F. ) ; +#77728 = CARTESIAN_POINT ( 'NONE', ( 1.870562122921110015, -1.007076035477679987, 0.8100000000000008304 ) ) ; +#77729 = FILL_AREA_STYLE_COLOUR ( '', #5461 ) ; +#77730 = PRESENTATION_STYLE_ASSIGNMENT (( #40972 ) ) ; +#77731 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01500000000000000118, 0.2399999999999999911 ) ) ; +#77732 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77733 = AXIS2_PLACEMENT_3D ( 'NONE', #29544, #60711, #404 ) ; +#77734 = SURFACE_STYLE_USAGE ( .BOTH. , #624 ) ; +#77735 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38602 ) ) ; +#77736 = SURFACE_SIDE_STYLE ('',( #7200 ) ) ; +#77737 = CARTESIAN_POINT ( 'NONE', ( -0.09294028489466890641, -0.9003478538782040408, 0.8100000000000000533 ) ) ; +#77738 = EDGE_CURVE ( 'NONE', #19644, #38462, #43757, .T. ) ; +#77739 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77740 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88600, 'distance_accuracy_value', 'NONE'); +#77741 = EDGE_CURVE ( 'NONE', #69329, #52068, #74427, .T. ) ; +#77742 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77743 = VERTEX_POINT ( 'NONE', #11030 ) ; +#77744 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#77745 = ORIENTED_EDGE ( 'NONE', *, *, #13185, .T. ) ; +#77746 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #709, 'distance_accuracy_value', 'NONE'); +#77747 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94860, 'distance_accuracy_value', 'NONE'); +#77748 = EDGE_CURVE ( 'NONE', #27727, #9645, #19792, .T. ) ; +#77749 = ADVANCED_FACE ( 'NONE', ( #42283 ), #58631, .T. ) ; +#77750 = LINE ( 'NONE', #54283, #91129 ) ; +#77751 = LINE ( 'NONE', #54284, #52854 ) ; +#77752 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82648 ), #90810 ) ; +#77753 = STYLED_ITEM ( 'NONE', ( #15141 ), #90788 ) ; +#77754 = SURFACE_SIDE_STYLE ('',( #46593 ) ) ; +#77755 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77756 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#77757 = VERTEX_POINT ( 'NONE', #90228 ) ; +#77758 = FILL_AREA_STYLE ('',( #92545 ) ) ; +#77759 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90818 ), #54969 ) ; +#77760 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#77761 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54613, 'distance_accuracy_value', 'NONE'); +#77762 = FACE_OUTER_BOUND ( 'NONE', #18884, .T. ) ; +#77763 = ORIENTED_EDGE ( 'NONE', *, *, #34030, .T. ) ; +#77764 = FILL_AREA_STYLE ('',( #38967 ) ) ; +#77765 = ADVANCED_FACE ( 'NONE', ( #44250 ), #27977, .T. ) ; +#77766 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77767 = ORIENTED_EDGE ( 'NONE', *, *, #30864, .T. ) ; +#77768 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77769 = SURFACE_STYLE_USAGE ( .BOTH. , #85926 ) ; +#77770 = ADVANCED_FACE ( 'NONE', ( #52444 ), #45729, .T. ) ; +#77771 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.5000000000000000000, 0.1829999999999659954 ) ) ; +#77772 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77773 = PRESENTATION_STYLE_ASSIGNMENT (( #94049 ) ) ; +#77774 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77775 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77776 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95674 ), #50124 ) ; +#77777 = ORIENTED_EDGE ( 'NONE', *, *, #52083, .F. ) ; +#77778 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#77779 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17455, 'distance_accuracy_value', 'NONE'); +#77780 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5928 ) ) ; +#77781 = AXIS2_PLACEMENT_3D ( 'NONE', #94689, #87074, #70210 ) ; +#77782 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77783 = CIRCLE ( 'NONE', #54994, 0.05000000000000002359 ) ; +#77784 = VERTEX_POINT ( 'NONE', #15083 ) ; +#77785 = AXIS2_PLACEMENT_3D ( 'NONE', #57324, #96570, #87932 ) ; +#77786 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.600000000000000089, -11.32000000000000028 ) ) ; +#77787 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77788 = PLANE ( 'NONE', #69539 ) ; +#77789 = VERTEX_POINT ( 'NONE', #22806 ) ; +#77790 = ORIENTED_EDGE ( 'NONE', *, *, #97085, .F. ) ; +#77791 = VECTOR ( 'NONE', #80815, 1000.000000000000000 ) ; +#77792 = ORIENTED_EDGE ( 'NONE', *, *, #54749, .F. ) ; +#77793 = VECTOR ( 'NONE', #7025, 1000.000000000000000 ) ; +#77794 = EDGE_CURVE ( 'NONE', #79108, #67213, #304, .T. ) ; +#77795 = ORIENTED_EDGE ( 'NONE', *, *, #81733, .F. ) ; +#77797 = VERTEX_POINT ( 'NONE', #85576 ) ; +#77796 = FILL_AREA_STYLE_COLOUR ( '', #86783 ) ; +#77798 = AXIS2_PLACEMENT_3D ( 'NONE', #66003, #3213, #11279 ) ; +#77799 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77800 = CARTESIAN_POINT ( 'NONE', ( 4.953618500499952226, 3.393294500499948185, 0.8991599999999999593 ) ) ; +#77801 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#77802 = ORIENTED_EDGE ( 'NONE', *, *, #3516, .T. ) ; +#77803 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77804 = CARTESIAN_POINT ( 'NONE', ( -2.676179938779915002, -3.100000000000000089, 0.000000000000000000 ) ) ; +#77805 = ORIENTED_EDGE ( 'NONE', *, *, #8214, .F. ) ; +#77806 = FACE_OUTER_BOUND ( 'NONE', #60599, .T. ) ; +#77807 = CYLINDRICAL_SURFACE ( 'NONE', #38254, 0.05000000000000012768 ) ; +#77808 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#77809 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77810 = ORIENTED_EDGE ( 'NONE', *, *, #37206, .F. ) ; +#77811 = ORIENTED_EDGE ( 'NONE', *, *, #96653, .T. ) ; +#77812 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66722, #3941, #35124, #89712 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#77813 = AXIS2_PLACEMENT_3D ( 'NONE', #6929, #76454, #67285 ) ; +#77814 = FILL_AREA_STYLE_COLOUR ( '', #27846 ) ; +#77815 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8991599999999999593 ) ) ; +#77816 = CARTESIAN_POINT ( 'NONE', ( 0.1500588324485339908, -1.474796765042009961, 0.8299999999999982947 ) ) ; +#77817 = EDGE_LOOP ( 'NONE', ( #82633, #42443, #43270, #79078 ) ) ; +#77818 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77819 = ORIENTED_EDGE ( 'NONE', *, *, #60037, .F. ) ; +#77820 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77821 = PRESENTATION_STYLE_ASSIGNMENT (( #84970 ) ) ; +#77822 = AXIS2_PLACEMENT_3D ( 'NONE', #19598, #5233, #60447 ) ; +#77824 = EDGE_CURVE ( 'NONE', #21305, #22729, #46756, .T. ) ; +#77823 = FILL_AREA_STYLE_COLOUR ( '', #45568 ) ; +#77825 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1292, 'distance_accuracy_value', 'NONE'); +#77826 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#77827 = STYLED_ITEM ( 'NONE', ( #97018 ), #79253 ) ; +#77828 = SURFACE_STYLE_FILL_AREA ( #63553 ) ; +#77829 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#77830 = FACE_OUTER_BOUND ( 'NONE', #97954, .T. ) ; +#77831 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77832 = LINE ( 'NONE', #32393, #28299 ) ; +#77833 = FILL_AREA_STYLE ('',( #94648 ) ) ; +#77834 = AXIS2_PLACEMENT_3D ( 'NONE', #75416, #45736, #61634 ) ; +#77835 = VERTEX_POINT ( 'NONE', #60620 ) ; +#77836 = CARTESIAN_POINT ( 'NONE', ( -1.268301777710219902, -1.110638925478639960, 0.8300000000000002931 ) ) ; +#77837 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#77838 = VECTOR ( 'NONE', #96675, 1000.000000000000000 ) ; +#77839 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63231 ), #7633 ) ; +#77841 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77840 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77842 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#77843 = PRESENTATION_STYLE_ASSIGNMENT (( #63054 ) ) ; +#77844 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.4245906043549200204, 0.2100000000000000200 ) ) ; +#77845 = VECTOR ( 'NONE', #97185, 1000.000000000000114 ) ; +#77846 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77847 = CARTESIAN_POINT ( 'NONE', ( -1.294533524454640094, -1.379057077391790287, 0.8299999999999998490 ) ) ; +#77848 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77849 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#77850 = CLOSED_SHELL ( 'NONE', ( #15216, #70167, #23600, #57754, #56588, #90653 ) ) ; +#77851 = LINE ( 'NONE', #6329, #68931 ) ; +#77852 = ORIENTED_EDGE ( 'NONE', *, *, #47371, .F. ) ; +#77853 = AXIS2_PLACEMENT_3D ( 'NONE', #66663, #12464, #34565 ) ; +#77854 = DIRECTION ( 'NONE', ( 0.7071067811865484609, -0.7071067811865465735, 0.000000000000000000 ) ) ; +#77855 = LINE ( 'NONE', #64063, #71802 ) ; +#77856 = AXIS2_PLACEMENT_3D ( 'NONE', #76620, #5632, #6611 ) ; +#77857 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77858 = CARTESIAN_POINT ( 'NONE', ( -0.1013823343696960005, -1.445184491613219935, 0.8100000000000000533 ) ) ; +#77859 = SURFACE_STYLE_USAGE ( .BOTH. , #46695 ) ; +#77860 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#77861 = STYLED_ITEM ( 'NONE', ( #97632 ), #50303 ) ; +#77862 = SURFACE_STYLE_USAGE ( .BOTH. , #54914 ) ; +#77863 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#77864 = FILL_AREA_STYLE_COLOUR ( '', #74591 ) ; +#77865 = LINE ( 'NONE', #253, #16192 ) ; +#77866 = PRESENTATION_STYLE_ASSIGNMENT (( #93144 ) ) ; +#77867 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#77868 = ORIENTED_EDGE ( 'NONE', *, *, #58383, .F. ) ; +#77869 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11285, 'distance_accuracy_value', 'NONE'); +#77870 = VECTOR ( 'NONE', #91790, 1000.000000000000114 ) ; +#77872 = EDGE_CURVE ( 'NONE', #71585, #39991, #100277, .T. ) ; +#77871 = SURFACE_STYLE_USAGE ( .BOTH. , #1275 ) ; +#77873 = SURFACE_SIDE_STYLE ('',( #14029 ) ) ; +#77874 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77875 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77876 = CARTESIAN_POINT ( 'NONE', ( -1.166406359071090026, -1.149778012002649952, 0.8100000000000000533 ) ) ; +#77877 = ORIENTED_EDGE ( 'NONE', *, *, #87544, .T. ) ; +#77878 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#77879 = CARTESIAN_POINT ( 'NONE', ( 5.696080875125044685, 3.570071124874956592, 0.8991599999999999593 ) ) ; +#77880 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2489, 'distance_accuracy_value', 'NONE'); +#77881 = AXIS2_PLACEMENT_3D ( 'NONE', #56210, #26070, #32717 ) ; +#77882 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77883 = VECTOR ( 'NONE', #78189, 1000.000000000000000 ) ; +#77884 = ORIENTED_EDGE ( 'NONE', *, *, #85518, .F. ) ; +#77885 = PRESENTATION_STYLE_ASSIGNMENT (( #8858 ) ) ; +#77886 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#77887 = ADVANCED_FACE ( 'NONE', ( #21784 ), #54465, .T. ) ; +#77888 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#77889 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.099999999999999867, -1.195472123049164304E-89 ) ) ; +#77890 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12590 ), #100632 ) ; +#77891 = LINE ( 'NONE', #53407, #88005 ) ; +#77892 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#77893 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.09999999999999996392, -0.02000000000001464842 ) ) ; +#77894 = MANIFOLD_SOLID_BREP ( 'ÊäÈë105', #43589 ) ; +#77895 = ORIENTED_EDGE ( 'NONE', *, *, #93350, .F. ) ; +#77896 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#77897 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#77898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71410, 'distance_accuracy_value', 'NONE'); +#77899 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77900 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8100000000000000533 ) ) ; +#77901 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77902 = ORIENTED_EDGE ( 'NONE', *, *, #42514, .T. ) ; +#77903 = SURFACE_SIDE_STYLE ('',( #46736 ) ) ; +#77904 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#77905 = EDGE_LOOP ( 'NONE', ( #7095, #39606, #38905, #67232 ) ) ; +#77906 = CARTESIAN_POINT ( 'NONE', ( -0.03276632349404259847, -1.496872818153279994, 0.8299999999999999600 ) ) ; +#77907 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77908 = EDGE_CURVE ( 'NONE', #70482, #79240, #95219, .T. ) ; +#77909 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#77910 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71439 ) ) ; +#77911 = STYLED_ITEM ( 'NONE', ( #60202 ), #62649 ) ; +#77912 = EDGE_LOOP ( 'NONE', ( #25082, #32199, #19150, #90854, #83210, #13951 ) ) ; +#77913 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8991599999999999593 ) ) ; +#77914 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77915 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60025 ) ) ; +#77916 = LINE ( 'NONE', #78423, #80046 ) ; +#77917 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#77918 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#77919 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, 0.1829999999999959992 ) ) ; +#77920 = CLOSED_SHELL ( 'NONE', ( #21502, #28257, #32088, #57240, #37222, #74595 ) ) ; +#77921 = ADVANCED_FACE ( 'NONE', ( #34012 ), #48329, .T. ) ; +#77922 = ORIENTED_EDGE ( 'NONE', *, *, #53794, .T. ) ; +#77923 = STYLED_ITEM ( 'NONE', ( #43444 ), #40306 ) ; +#77924 = LINE ( 'NONE', #305, #26127 ) ; +#77925 = STYLED_ITEM ( 'NONE', ( #75503 ), #100658 ) ; +#77926 = PRESENTATION_STYLE_ASSIGNMENT (( #67378 ) ) ; +#77927 = SURFACE_STYLE_USAGE ( .BOTH. , #45239 ) ; +#77928 = ORIENTED_EDGE ( 'NONE', *, *, #30293, .T. ) ; +#77929 = AXIS2_PLACEMENT_3D ( 'NONE', #34801, #97987, #75581 ) ; +#77931 = LINE ( 'NONE', #86597, #1232 ) ; +#77930 = PLANE ( 'NONE', #82989 ) ; +#77932 = ORIENTED_EDGE ( 'NONE', *, *, #97389, .T. ) ; +#77933 = ORIENTED_EDGE ( 'NONE', *, *, #30546, .T. ) ; +#77934 = CARTESIAN_POINT ( 'NONE', ( 1.363156991944870056, -1.321802795360440319, 0.8100000000000000533 ) ) ; +#77935 = CIRCLE ( 'NONE', #74742, 0.2000000000000000111 ) ; +#77936 = FILL_AREA_STYLE_COLOUR ( '', #25089 ) ; +#77937 = PLANE ( 'NONE', #94628 ) ; +#77938 = SURFACE_SIDE_STYLE ('',( #320 ) ) ; +#77939 = ORIENTED_EDGE ( 'NONE', *, *, #68163, .T. ) ; +#77940 = AXIS2_PLACEMENT_3D ( 'NONE', #63474, #85904, #1673 ) ; +#77941 = PRESENTATION_STYLE_ASSIGNMENT (( #54481 ) ) ; +#77942 = FILL_AREA_STYLE_COLOUR ( '', #60188 ) ; +#77943 = LINE ( 'NONE', #1861, #96306 ) ; +#77944 = VERTEX_POINT ( 'NONE', #78930 ) ; +#77946 = SURFACE_STYLE_USAGE ( .BOTH. , #30438 ) ; +#77945 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#77947 = CARTESIAN_POINT ( 'NONE', ( -3.200000000000000178, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#77948 = VERTEX_POINT ( 'NONE', #31972 ) ; +#77949 = ORIENTED_EDGE ( 'NONE', *, *, #14455, .F. ) ; +#77950 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77951 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91218 ) ) ; +#77953 = SURFACE_STYLE_FILL_AREA ( #38157 ) ; +#77952 = CYLINDRICAL_SURFACE ( 'NONE', #72183, 0.05000000000000012768 ) ; +#77954 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#77955 = EDGE_CURVE ( 'NONE', #58354, #97934, #47280, .T. ) ; +#77956 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#77957 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6171 ), #89404 ) ; +#77958 = LINE ( 'NONE', #12841, #64567 ) ; +#77959 = AXIS2_PLACEMENT_3D ( 'NONE', #92643, #78378, #8332 ) ; +#77960 = VECTOR ( 'NONE', #13690, 1000.000000000000000 ) ; +#77962 = EDGE_CURVE ( 'NONE', #74424, #6846, #87604, .T. ) ; +#77961 = CARTESIAN_POINT ( 'NONE', ( -0.02773322717383189945, -1.124571705400470023, 0.8100000000000000533 ) ) ; +#77963 = FILL_AREA_STYLE ('',( #15638 ) ) ; +#77964 = VECTOR ( 'NONE', #11338, 1000.000000000000000 ) ; +#77965 = ORIENTED_EDGE ( 'NONE', *, *, #44114, .T. ) ; +#77966 = SURFACE_STYLE_USAGE ( .BOTH. , #99815 ) ; +#77967 = DIRECTION ( 'NONE', ( -0.7071075504167442238, 0.7071060119555140355, 0.000000000000000000 ) ) ; +#77968 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77969 = STYLED_ITEM ( 'NONE', ( #48568 ), #56490 ) ; +#77970 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.300000000000000266, -0.02000000000000839995 ) ) ; +#77971 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37254 ), #1302 ) ; +#77972 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20907 ), #87743 ) ; +#77973 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.500000000000000000, 0.000000000000000000 ) ) ; +#77974 = FACE_OUTER_BOUND ( 'NONE', #8509, .T. ) ; +#77975 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000000513, 0.8648700000000000276 ) ) ; +#77976 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#77977 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#77978 = EDGE_CURVE ( 'NONE', #62858, #23866, #9414, .T. ) ; +#77980 = ORIENTED_EDGE ( 'NONE', *, *, #10033, .F. ) ; +#77979 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100730 ) ) ; +#77981 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#77982 = PRESENTATION_STYLE_ASSIGNMENT (( #31008 ) ) ; +#77983 = SURFACE_STYLE_FILL_AREA ( #85127 ) ; +#77984 = CARTESIAN_POINT ( 'NONE', ( 3.716182000000000318, 5.549970000000000070, 0.8991599999999999593 ) ) ; +#77985 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77986 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48708 ), #12749 ) ; +#77987 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#77988 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96334, 'distance_accuracy_value', 'NONE'); +#77989 = CARTESIAN_POINT ( 'NONE', ( 4.232370000000001298, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#77990 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#77991 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#77992 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#77993 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#77994 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#77995 = SURFACE_SIDE_STYLE ('',( #87668 ) ) ; +#77996 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#77997 = SURFACE_STYLE_USAGE ( .BOTH. , #47350 ) ; +#77998 = VECTOR ( 'NONE', #95256, 1000.000000000000000 ) ; +#77999 = VECTOR ( 'NONE', #43223, 1000.000000000000000 ) ; +#78001 = EDGE_CURVE ( 'NONE', #25241, #2974, #94225, .T. ) ; +#78000 = PRESENTATION_STYLE_ASSIGNMENT (( #46827 ) ) ; +#78002 = PLANE ( 'NONE', #78086 ) ; +#78003 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #16218, 'design' ) ; +#78004 = CLOSED_SHELL ( 'NONE', ( #32497, #54938, #70091, #41065, #30216, #21348 ) ) ; +#78005 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8648700000000000276 ) ) ; +#78006 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.000000000000000000, 0.2999999999999999889 ) ) ; +#78007 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#78008 = ORIENTED_EDGE ( 'NONE', *, *, #64473, .T. ) ; +#78009 = CARTESIAN_POINT ( 'NONE', ( -0.4296857479143016412, -1.257700959484805869, 0.8100000000000305844 ) ) ; +#78010 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78011 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.3000000000000000444, 1.048695503451051965E-76 ) ) ; +#78012 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38868 ) ) ; +#78013 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#78014 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86613, 'distance_accuracy_value', 'NONE'); +#78015 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78016 = FILL_AREA_STYLE ('',( #69825 ) ) ; +#78017 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50365 ) ) ; +#78018 = EDGE_CURVE ( 'NONE', #32731, #58022, #88121, .T. ) ; +#78019 = CARTESIAN_POINT ( 'NONE', ( 1.736267301452500300, -1.505252428432260148, 0.8300000000000011813 ) ) ; +#78020 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78021 = ORIENTED_EDGE ( 'NONE', *, *, #10931, .F. ) ; +#78022 = SURFACE_SIDE_STYLE ('',( #46848 ) ) ; +#78023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86165 ), #16039 ) ; +#78024 = CARTESIAN_POINT ( 'NONE', ( 1.821320548784939986, -1.306448053922619978, 0.8299999999999994049 ) ) ; +#78025 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36164, 'distance_accuracy_value', 'NONE'); +#78026 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78027 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15961, 'distance_accuracy_value', 'NONE'); +#78028 = EDGE_LOOP ( 'NONE', ( #65744, #63244, #1172, #95995 ) ) ; +#78029 = EDGE_LOOP ( 'NONE', ( #86990, #94525, #45590, #33522 ) ) ; +#78030 = FACE_OUTER_BOUND ( 'NONE', #16877, .T. ) ; +#78031 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76409 ) ) ; +#78032 = ORIENTED_EDGE ( 'NONE', *, *, #16581, .T. ) ; +#78033 = CARTESIAN_POINT ( 'NONE', ( -0.1950643281718389965, -1.495500525511030077, 0.8299999999999999600 ) ) ; +#78034 = AXIS2_PLACEMENT_3D ( 'NONE', #13052, #50475, #81608 ) ; +#78035 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#78036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21709, 'distance_accuracy_value', 'NONE'); +#78037 = DIRECTION ( 'NONE', ( -1.019578823124770065E-47, 4.701977403289150032E-32, 1.000000000000000000 ) ) ; +#78038 = AXIS2_PLACEMENT_3D ( 'NONE', #73004, #3056, #34227 ) ; +#78039 = AXIS2_PLACEMENT_3D ( 'NONE', #63207, #33043, #39182 ) ; +#78040 = SHAPE_DEFINITION_REPRESENTATION ( #48971, #74319 ) ; +#78041 = SURFACE_STYLE_USAGE ( .BOTH. , #46869 ) ; +#78042 = EDGE_CURVE ( 'NONE', #95213, #54575, #70762, .T. ) ; +#78044 = ORIENTED_EDGE ( 'NONE', *, *, #61984, .T. ) ; +#78043 = EDGE_LOOP ( 'NONE', ( #23293, #49522, #79056, #28824 ) ) ; +#78045 = VECTOR ( 'NONE', #93328, 1000.000000000000000 ) ; +#78046 = ORIENTED_EDGE ( 'NONE', *, *, #59339, .F. ) ; +#78047 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.500000000000000222, -0.02000000000000000042 ) ) ; +#78048 = STYLED_ITEM ( 'NONE', ( #30616 ), #91726 ) ; +#78049 = PLANE ( 'NONE', #75151 ) ; +#78051 = SURFACE_STYLE_USAGE ( .BOTH. , #40770 ) ; +#78050 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -2.366666666666666696, 0.000000000000000000 ) ) ; +#78052 = ORIENTED_EDGE ( 'NONE', *, *, #77602, .F. ) ; +#78053 = EDGE_CURVE ( 'NONE', #94446, #12927, #97724, .T. ) ; +#78054 = STYLED_ITEM ( 'NONE', ( #93656 ), #55761 ) ; +#78055 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37329 ) ) ; +#78056 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78057 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78133 ), #6267 ) ; +#78058 = SURFACE_STYLE_USAGE ( .BOTH. , #7507 ) ; +#78059 = ORIENTED_EDGE ( 'NONE', *, *, #99169, .T. ) ; +#78060 = CARTESIAN_POINT ( 'NONE', ( -0.5701283358897649700, -0.9702412545157700352, 0.8100000000000000533 ) ) ; +#78061 = ORIENTED_EDGE ( 'NONE', *, *, #14036, .F. ) ; +#78062 = VERTEX_POINT ( 'NONE', #20660 ) ; +#78063 = LINE ( 'NONE', #7512, #46021 ) ; +#78064 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60175 ), #3070 ) ; +#78065 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999939959, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#78067 = MANIFOLD_SOLID_BREP ( 'ÊäÈë20', #6142 ) ; +#78066 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65029 ), #74938 ) ; +#78068 = SURFACE_STYLE_FILL_AREA ( #46896 ) ; +#78070 = ORIENTED_EDGE ( 'NONE', *, *, #45897, .F. ) ; +#78069 = FILL_AREA_STYLE ('',( #53586 ) ) ; +#78072 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43879 ) ) ; +#78071 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#78073 = SURFACE_SIDE_STYLE ('',( #966 ) ) ; +#78074 = EDGE_LOOP ( 'NONE', ( #49587, #54472, #13145, #32140, #39849, #42319 ) ) ; +#78075 = PRESENTATION_STYLE_ASSIGNMENT (( #48467 ) ) ; +#78076 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78077 = ORIENTED_EDGE ( 'NONE', *, *, #17179, .T. ) ; +#78078 = ORIENTED_EDGE ( 'NONE', *, *, #3416, .T. ) ; +#78080 = SURFACE_STYLE_FILL_AREA ( #91875 ) ; +#78079 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78081 = CARTESIAN_POINT ( 'NONE', ( 1.719030235149860086, -1.443664018207750033, 0.8300000000000002931 ) ) ; +#78082 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78083 = AXIS2_PLACEMENT_3D ( 'NONE', #32017, #42068, #73225 ) ; +#78084 = ADVANCED_FACE ( 'NONE', ( #89618 ), #73460, .F. ) ; +#78085 = EDGE_CURVE ( 'NONE', #89795, #25673, #5811, .T. ) ; +#78087 = SURFACE_STYLE_FILL_AREA ( #9562 ) ; +#78086 = AXIS2_PLACEMENT_3D ( 'NONE', #1910, #32561, #70325 ) ; +#78088 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#78089 = EDGE_LOOP ( 'NONE', ( #8874, #44897, #20857, #74974 ) ) ; +#78090 = LINE ( 'NONE', #77077, #87096 ) ; +#78091 = ORIENTED_EDGE ( 'NONE', *, *, #48946, .T. ) ; +#78092 = FACE_OUTER_BOUND ( 'NONE', #64592, .T. ) ; +#78093 = SURFACE_STYLE_FILL_AREA ( #46927 ) ; +#78094 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32692 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20367, #45325, #5989 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78095 = FILL_AREA_STYLE_COLOUR ( '', #79352 ) ; +#78096 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78097 = SURFACE_SIDE_STYLE ('',( #31626 ) ) ; +#78098 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#78099 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100493, 'distance_accuracy_value', 'NONE'); +#78100 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#78101 = EDGE_CURVE ( 'NONE', #35923, #47262, #8954, .T. ) ; +#78102 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#78103 = EDGE_CURVE ( 'NONE', #40797, #97279, #32630, .T. ) ; +#78104 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 12.10755799999999915, 0.8991599999999999593 ) ) ; +#78105 = SURFACE_STYLE_FILL_AREA ( #46940 ) ; +#78106 = LINE ( 'NONE', #39281, #65716 ) ; +#78107 = SURFACE_STYLE_USAGE ( .BOTH. , #84749 ) ; +#78108 = CIRCLE ( 'NONE', #40654, 0.6999999999379724613 ) ; +#78109 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#78110 = FILL_AREA_STYLE_COLOUR ( '', #28702 ) ; +#78111 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29211 ) ) ; +#78112 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45481 ) ) ; +#78114 = FACE_OUTER_BOUND ( 'NONE', #39980, .T. ) ; +#78113 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78115 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78116 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#78117 = STYLED_ITEM ( 'NONE', ( #42035 ), #57115 ) ; +#78118 = AXIS2_PLACEMENT_3D ( 'NONE', #68938, #67940, #90958 ) ; +#78119 = EDGE_CURVE ( 'NONE', #89849, #82440, #92269, .T. ) ; +#78120 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52294, 'distance_accuracy_value', 'NONE'); +#78121 = STYLED_ITEM ( 'NONE', ( #19731 ), #81122 ) ; +#78122 = ORIENTED_EDGE ( 'NONE', *, *, #71237, .T. ) ; +#78123 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78124 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78125 = VERTEX_POINT ( 'NONE', #69087 ) ; +#78126 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65087 ) ) ; +#78127 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#78128 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78129 = EDGE_CURVE ( 'NONE', #41417, #60158, #28826, .T. ) ; +#78130 = PRESENTATION_STYLE_ASSIGNMENT (( #24547 ) ) ; +#78131 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999962044, 0.3000000000000000444, 0.5799137866959191978 ) ) ; +#78132 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 2.261924000000000046, 0.8991599999999999593 ) ) ; +#78133 = STYLED_ITEM ( 'NONE', ( #45652 ), #80133 ) ; +#78134 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#78135 = AXIS2_PLACEMENT_3D ( 'NONE', #78743, #87921, #32798 ) ; +#78136 = EDGE_LOOP ( 'NONE', ( #91371, #49344, #34621, #56297 ) ) ; +#78137 = PLANE ( 'NONE', #33494 ) ; +#78138 = EDGE_CURVE ( 'NONE', #27289, #14189, #75793, .T. ) ; +#78139 = ORIENTED_EDGE ( 'NONE', *, *, #35372, .F. ) ; +#78140 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92802 ) ) ; +#78141 = PRESENTATION_STYLE_ASSIGNMENT (( #46981 ) ) ; +#78142 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#78144 = VECTOR ( 'NONE', #46812, 1000.000000000000000 ) ; +#78143 = PRESENTATION_STYLE_ASSIGNMENT (( #54153 ) ) ; +#78145 = SURFACE_SIDE_STYLE ('',( #55691 ) ) ; +#78146 = EDGE_CURVE ( 'NONE', #55010, #47598, #77465, .T. ) ; +#78147 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460165, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#78148 = SURFACE_STYLE_FILL_AREA ( #15302 ) ; +#78149 = SURFACE_STYLE_FILL_AREA ( #77636 ) ; +#78150 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78151 = LINE ( 'NONE', #7093, #23298 ) ; +#78152 = VECTOR ( 'NONE', #84722, 1000.000000000000000 ) ; +#78153 = EDGE_LOOP ( 'NONE', ( #80720, #46002, #97590, #2672 ) ) ; +#78154 = PRODUCT_DEFINITION ( 'δ֪', '', #99070, #34082 ) ; +#78155 = DIRECTION ( 'NONE', ( -0.7071062811861718034, 0.7071072811865697361, 0.000000000000000000 ) ) ; +#78156 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506899999999902, 0.8648700000000000276 ) ) ; +#78157 = ORIENTED_EDGE ( 'NONE', *, *, #56197, .F. ) ; +#78158 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78159 = FACE_OUTER_BOUND ( 'NONE', #81854, .T. ) ; +#78160 = ORIENTED_EDGE ( 'NONE', *, *, #7465, .T. ) ; +#78161 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65109 ) ) ; +#78162 = CARTESIAN_POINT ( 'NONE', ( 1.089738207395029912, -1.411115659170130154, 0.8100000000000000533 ) ) ; +#78163 = PRESENTATION_STYLE_ASSIGNMENT (( #47000 ) ) ; +#78164 = FILL_AREA_STYLE_COLOUR ( '', #10377 ) ; +#78165 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78166 = CARTESIAN_POINT ( 'NONE', ( 1.877211804471180079, -1.084027901463999966, 0.8100000000000000533 ) ) ; +#78167 = EDGE_CURVE ( 'NONE', #58245, #42023, #27758, .T. ) ; +#78168 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#78170 = VERTEX_POINT ( 'NONE', #83962 ) ; +#78169 = ORIENTED_EDGE ( 'NONE', *, *, #28909, .T. ) ; +#78171 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #26016, #16784, #64794, #33157, #70953, #87268, #57172, #63809, #9579, #8559, #86772, #79130, #41830, #40833, #10570, #18302, #10069 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.492633351254281356E-05, 4.988459961574794879E-05, 6.202023387223060179E-05, 7.381064975062877505E-05, 8.522929490718315318E-05, 9.648269829191059789E-05, 0.0001074668139312685524, 0.0001183815562236670505, 0.0001293286825426029547, 0.0001405453271619729451, 0.0001521160265971559743, 0.0001642953361755772692, 0.0001773332741803510079, 0.0001914400125203943046 ), + .UNSPECIFIED. ) ; +#78172 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57200 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98780, #83553, #20239 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78173 = ORIENTED_EDGE ( 'NONE', *, *, #11999, .F. ) ; +#78175 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78174 = SURFACE_STYLE_FILL_AREA ( #47521 ) ; +#78176 = EDGE_LOOP ( 'NONE', ( #30067, #98542 ) ) ; +#78177 = EDGE_CURVE ( 'NONE', #56618, #27071, #22682, .T. ) ; +#78178 = ORIENTED_EDGE ( 'NONE', *, *, #8928, .F. ) ; +#78179 = LINE ( 'NONE', #30671, #56401 ) ; +#78180 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78181 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78182 = VECTOR ( 'NONE', #47679, 1000.000000000000000 ) ; +#78184 = CARTESIAN_POINT ( 'NONE', ( 13.17837699999999934, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#78183 = SURFACE_STYLE_FILL_AREA ( #69479 ) ; +#78185 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#78186 = ORIENTED_EDGE ( 'NONE', *, *, #62352, .T. ) ; +#78187 = ADVANCED_FACE ( 'NONE', ( #77806 ), #91120, .T. ) ; +#78188 = ORIENTED_EDGE ( 'NONE', *, *, #89187, .T. ) ; +#78189 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#78190 = ORIENTED_EDGE ( 'NONE', *, *, #6566, .F. ) ; +#78191 = PLANE ( 'NONE', #73700 ) ; +#78192 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43218 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99697, #21699, #45149 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78193 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55400 ) ) ; +#78194 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78196 = EDGE_LOOP ( 'NONE', ( #5932, #73970, #14852, #41004 ) ) ; +#78195 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, 0.000000000000000000 ) ) ; +#78197 = STYLED_ITEM ( 'NONE', ( #41746 ), #85088 ) ; +#78198 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96315 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91560, #76235, #6233 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78199 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78200 = FILL_AREA_STYLE_COLOUR ( '', #12261 ) ; +#78201 = EDGE_LOOP ( 'NONE', ( #6806, #91724, #92894, #22443 ) ) ; +#78202 = SHAPE_REPRESENTATION ( 'Submodel-C0201_part_C0201', ( #58257, #77733 ), #74486 ) ; +#78203 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11621 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15023, #61067, #69151 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78204 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.850000000000000311, 0.000000000000000000 ) ) ; +#78205 = ORIENTED_EDGE ( 'NONE', *, *, #98675, .T. ) ; +#78206 = AXIS2_PLACEMENT_3D ( 'NONE', #7741, #6739, #61987 ) ; +#78207 = FACE_OUTER_BOUND ( 'NONE', #95100, .T. ) ; +#78209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78208 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37409 ) ) ; +#78210 = PRESENTATION_STYLE_ASSIGNMENT (( #15879 ) ) ; +#78211 = ORIENTED_EDGE ( 'NONE', *, *, #48292, .F. ) ; +#78212 = EDGE_CURVE ( 'NONE', #10057, #87203, #54853, .T. ) ; +#78213 = LINE ( 'NONE', #78693, #80185 ) ; +#78214 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78216 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.000000000000000000 ) ) ; +#78215 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78217 = FILL_AREA_STYLE_COLOUR ( '', #39311 ) ; +#78218 = VECTOR ( 'NONE', #80135, 1000.000000000000000 ) ; +#78219 = LINE ( 'NONE', #16379, #7043 ) ; +#78220 = ORIENTED_EDGE ( 'NONE', *, *, #15368, .F. ) ; +#78221 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#78222 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000003553, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#78223 = AXIS2_PLACEMENT_3D ( 'NONE', #96669, #50278, #97168 ) ; +#78224 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000089, 3.099999999999995204, -0.02000000000000000042 ) ) ; +#78225 = LINE ( 'NONE', #87, #88717 ) ; +#78226 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78227 = PLANE ( 'NONE', #85002 ) ; +#78228 = SURFACE_SIDE_STYLE ('',( #47060 ) ) ; +#78229 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, -3.099999999999989875, 0.000000000000000000 ) ) ; +#78230 = FACE_OUTER_BOUND ( 'NONE', #87441, .T. ) ; +#78231 = EDGE_CURVE ( 'NONE', #67521, #58234, #15999, .T. ) ; +#78232 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94524 ), #8081 ) ; +#78233 = CYLINDRICAL_SURFACE ( 'NONE', #86415, 0.009999999999999998473 ) ; +#78234 = ORIENTED_EDGE ( 'NONE', *, *, #66389, .F. ) ; +#78235 = EDGE_CURVE ( 'NONE', #28348, #28967, #70131, .T. ) ; +#78236 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#78237 = STYLED_ITEM ( 'NONE', ( #28167 ), #15654 ) ; +#78238 = ORIENTED_EDGE ( 'NONE', *, *, #10546, .F. ) ; +#78239 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78241 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78240 = PLANE ( 'NONE', #40982 ) ; +#78242 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#78243 = MANIFOLD_SOLID_BREP ( 'ÊäÈë117', #58304 ) ; +#78245 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63615 ) ) ; +#78244 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78246 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78247 = AXIS2_PLACEMENT_3D ( 'NONE', #51534, #1123, #72093 ) ; +#78248 = FILL_AREA_STYLE_COLOUR ( '', #59236 ) ; +#78249 = ORIENTED_EDGE ( 'NONE', *, *, #781, .F. ) ; +#78250 = FACE_OUTER_BOUND ( 'NONE', #10632, .T. ) ; +#78251 = CARTESIAN_POINT ( 'NONE', ( -0.008157340354953810171, -1.074567238704529970, 0.8300000000000005151 ) ) ; +#78252 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8648700000000000276 ) ) ; +#78253 = FILL_AREA_STYLE_COLOUR ( '', #32357 ) ; +#78254 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78255 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.383333333333330195, 0.000000000000000000 ) ) ; +#78256 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.499999999999989786, -0.02000000000000000042 ) ) ; +#78257 = SURFACE_STYLE_FILL_AREA ( #60937 ) ; +#78258 = CARTESIAN_POINT ( 'NONE', ( -0.05684101355748980011, -0.9053603395923379704, 0.8100000000000000533 ) ) ; +#78259 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3257 ), #68529 ) ; +#78260 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#78261 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.000000000000000000 ) ) ; +#78262 = ORIENTED_EDGE ( 'NONE', *, *, #49741, .T. ) ; +#78263 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 2.100000000000000089, 3.495651678170121160E-76 ) ) ; +#78264 = ADVANCED_FACE ( 'NONE', ( #25244 ), #86480, .T. ) ; +#78265 = ORIENTED_EDGE ( 'NONE', *, *, #96367, .T. ) ; +#78266 = VECTOR ( 'NONE', #32628, 1000.000000000000114 ) ; +#78267 = FILL_AREA_STYLE ('',( #46590 ) ) ; +#78268 = SURFACE_STYLE_FILL_AREA ( #47106 ) ; +#78269 = VECTOR ( 'NONE', #100249, 1000.000000000000000 ) ; +#78271 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78270 = AXIS2_PLACEMENT_3D ( 'NONE', #97068, #58848, #43473 ) ; +#78272 = DIRECTION ( 'NONE', ( -0.7071075504167435577, 0.7071060119555145906, 0.000000000000000000 ) ) ; +#78273 = AXIS2_PLACEMENT_3D ( 'NONE', #42051, #10810, #10294 ) ; +#78274 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78275 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.7000000000000001776, -0.02000000000000000042 ) ) ; +#78276 = VECTOR ( 'NONE', #92413, 1000.000000000000000 ) ; +#78277 = VERTEX_POINT ( 'NONE', #32369 ) ; +#78278 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#78279 = SURFACE_SIDE_STYLE ('',( #78763 ) ) ; +#78280 = SURFACE_STYLE_USAGE ( .BOTH. , #47629 ) ; +#78281 = VECTOR ( 'NONE', #45102, 1000.000000000000114 ) ; +#78282 = VERTEX_POINT ( 'NONE', #63528 ) ; +#78283 = CARTESIAN_POINT ( 'NONE', ( 1.254627500282712083, -1.237666169257944482, 0.8099999999998401812 ) ) ; +#78284 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62940, #39934, #71075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78285 = STYLED_ITEM ( 'NONE', ( #57814 ), #65162 ) ; +#78286 = VERTEX_POINT ( 'NONE', #55856 ) ; +#78287 = LINE ( 'NONE', #46607, #2154 ) ; +#78288 = FILL_AREA_STYLE_COLOUR ( '', #40336 ) ; +#78289 = PLANE ( 'NONE', #77222 ) ; +#78290 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45646 ), #34295 ) ; +#78291 = FACE_OUTER_BOUND ( 'NONE', #84712, .T. ) ; +#78292 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78293 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78294 = ORIENTED_EDGE ( 'NONE', *, *, #41219, .F. ) ; +#78295 = STYLED_ITEM ( 'NONE', ( #56503 ), #69134 ) ; +#78296 = LINE ( 'NONE', #69590, #74990 ) ; +#78297 = PLANE ( 'NONE', #5487 ) ; +#78298 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78299 = FILL_AREA_STYLE_COLOUR ( '', #96343 ) ; +#78300 = EDGE_CURVE ( 'NONE', #27945, #61829, #86991, .T. ) ; +#78301 = VERTEX_POINT ( 'NONE', #57380 ) ; +#78302 = AXIS2_PLACEMENT_3D ( 'NONE', #100390, #99896, #46368 ) ; +#78303 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78304 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78305 = SURFACE_STYLE_FILL_AREA ( #16991 ) ; +#78306 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78307 = ORIENTED_EDGE ( 'NONE', *, *, #82496, .F. ) ; +#78308 = ORIENTED_EDGE ( 'NONE', *, *, #91341, .T. ) ; +#78309 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#78310 = ORIENTED_EDGE ( 'NONE', *, *, #53661, .F. ) ; +#78311 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23505 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80778, #34822, #65951 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78312 = ADVANCED_FACE ( 'NONE', ( #18535 ), #50723, .T. ) ; +#78313 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11113 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25564, #27571, #34738 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78314 = ORIENTED_EDGE ( 'NONE', *, *, #152, .T. ) ; +#78315 = ORIENTED_EDGE ( 'NONE', *, *, #97328, .F. ) ; +#78316 = LINE ( 'NONE', #184, #49130 ) ; +#78317 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#78318 = FACE_OUTER_BOUND ( 'NONE', #62312, .T. ) ; +#78319 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -2.350550309948575893E-17, 0.4000000000000000777 ) ) ; +#78320 = VERTEX_POINT ( 'NONE', #21929 ) ; +#78321 = ADVANCED_FACE ( 'NONE', ( #6039 ), #72669, .F. ) ; +#78322 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#78323 = ORIENTED_EDGE ( 'NONE', *, *, #29469, .F. ) ; +#78324 = FILL_AREA_STYLE ('',( #47166 ) ) ; +#78325 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14712 ) ) ; +#78326 = ORIENTED_EDGE ( 'NONE', *, *, #73667, .F. ) ; +#78327 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78328 = ORIENTED_EDGE ( 'NONE', *, *, #84036, .T. ) ; +#78329 = ADVANCED_FACE ( 'NONE', ( #44877 ), #49722, .T. ) ; +#78330 = EDGE_CURVE ( 'NONE', #85412, #16737, #15498, .T. ) ; +#78331 = STYLED_ITEM ( 'NONE', ( #14097 ), #86156 ) ; +#78332 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71082 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34191, #65296, #80648 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78333 = SURFACE_STYLE_FILL_AREA ( #47172 ) ; +#78334 = FILL_AREA_STYLE ('',( #63541 ) ) ; +#78335 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#78336 = STYLED_ITEM ( 'NONE', ( #12061 ), #57691 ) ; +#78337 = EDGE_CURVE ( 'NONE', #81900, #30563, #58068, .T. ) ; +#78338 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, -0.6999999999999999556 ) ) ; +#78339 = EDGE_CURVE ( 'NONE', #61238, #35156, #78555, .T. ) ; +#78340 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22881 ), #26173 ) ; +#78341 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78342 = VERTEX_POINT ( 'NONE', #8520 ) ; +#78344 = PRESENTATION_STYLE_ASSIGNMENT (( #15503 ) ) ; +#78343 = VECTOR ( 'NONE', #21901, 1000.000000000000000 ) ; +#78345 = LINE ( 'NONE', #86501, #55430 ) ; +#78346 = EDGE_CURVE ( 'NONE', #21238, #48176, #42320, .T. ) ; +#78347 = STYLED_ITEM ( 'NONE', ( #60199 ), #80844 ) ; +#78348 = SURFACE_STYLE_USAGE ( .BOTH. , #45634 ) ; +#78349 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40834 ), #50682 ) ; +#78350 = SURFACE_STYLE_FILL_AREA ( #22706 ) ; +#78351 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#78352 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#78353 = EDGE_CURVE ( 'NONE', #4549, #72427, #13940, .T. ) ; +#78354 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78355 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#78356 = ORIENTED_EDGE ( 'NONE', *, *, #59429, .T. ) ; +#78357 = AXIS2_PLACEMENT_3D ( 'NONE', #30865, #69655, #14503 ) ; +#78358 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.033333333333333659, 0.000000000000000000 ) ) ; +#78359 = AXIS2_PLACEMENT_3D ( 'NONE', #78252, #94007, #1128 ) ; +#78360 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78361 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 8.031915000000001470, 0.8991599999999999593 ) ) ; +#78362 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9793, 'distance_accuracy_value', 'NONE'); +#78363 = VECTOR ( 'NONE', #94536, 1000.000000000000000 ) ; +#78364 = LINE ( 'NONE', #93120, #5446 ) ; +#78365 = CARTESIAN_POINT ( 'NONE', ( -1.191485992818250184, -1.440849955440170138, 0.8299999999999998490 ) ) ; +#78366 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#78367 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#78368 = ORIENTED_EDGE ( 'NONE', *, *, #42042, .F. ) ; +#78369 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78370 = FILL_AREA_STYLE ('',( #87037 ) ) ; +#78371 = VECTOR ( 'NONE', #360, 1000.000000000000000 ) ; +#78372 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.383333333333323090, 0.000000000000000000 ) ) ; +#78373 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#78374 = SURFACE_SIDE_STYLE ('',( #7326 ) ) ; +#78375 = FILL_AREA_STYLE ('',( #47222 ) ) ; +#78376 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#78377 = FILL_AREA_STYLE ('',( #29880 ) ) ; +#78378 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78379 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78380 = EDGE_LOOP ( 'NONE', ( #78507, #25834, #43183, #59025 ) ) ; +#78381 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78382 = ADVANCED_FACE ( 'NONE', ( #16241 ), #22423, .T. ) ; +#78383 = ORIENTED_EDGE ( 'NONE', *, *, #35079, .T. ) ; +#78384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25546 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90960, #44462, #75631 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78385 = CARTESIAN_POINT ( 'NONE', ( -0.2253841549269462452, -1.489562514595016873, 0.8099999999995148858 ) ) ; +#78386 = SURFACE_STYLE_FILL_AREA ( #9854 ) ; +#78387 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19854, #51026, #35707, #74496, #28039, #90292, #14654, #69275, #91788, #60683, #15156, #45803, #22350, #54014, #44312, #69810, #5972, #91301, #83660 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.579034425011571787E-05, 3.081603604638715241E-05, 4.491746013559986677E-05, 5.837560011014658959E-05, 7.117912044676800130E-05, 8.376220332114717919E-05, 9.603306182115256074E-05, 0.0001083585251528076688, 0.0001207930788422116429, 0.0001333113597912503120, 0.0001461759257520039068, 0.0001592721489571213931, 0.0001728423707183110122, 0.0001868402333759707499, 0.0002015609050938452099, 0.0002168387333276165807 ), + .UNSPECIFIED. ) ; +#78388 = PLANE ( 'NONE', #99653 ) ; +#78390 = EDGE_CURVE ( 'NONE', #98956, #86972, #48289, .T. ) ; +#78389 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78391 = CARTESIAN_POINT ( 'NONE', ( -1.277337950986729975, -1.102553831183370026, 0.8299999999999999600 ) ) ; +#78392 = ORIENTED_EDGE ( 'NONE', *, *, #41425, .F. ) ; +#78393 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.98066299999999984, 0.8648700000000000276 ) ) ; +#78394 = FACE_OUTER_BOUND ( 'NONE', #57970, .T. ) ; +#78395 = ORIENTED_EDGE ( 'NONE', *, *, #17112, .T. ) ; +#78396 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63618 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81870, #43533, #57387 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78397 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#78398 = PLANE ( 'NONE', #100894 ) ; +#78399 = LINE ( 'NONE', #1297, #21242 ) ; +#78400 = ORIENTED_EDGE ( 'NONE', *, *, #65154, .F. ) ; +#78401 = PRESENTATION_STYLE_ASSIGNMENT (( #47256 ) ) ; +#78402 = VECTOR ( 'NONE', #49852, 1000.000000000000000 ) ; +#78404 = SURFACE_SIDE_STYLE ('',( #39600 ) ) ; +#78403 = AXIS2_PLACEMENT_3D ( 'NONE', #70380, #62258, #70910 ) ; +#78405 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24350, 'distance_accuracy_value', 'NONE'); +#78406 = CARTESIAN_POINT ( 'NONE', ( -0.2926880133853450028, 0.2349715759269649928, 0.8299999999999999600 ) ) ; +#78407 = PRESENTATION_STYLE_ASSIGNMENT (( #30928 ) ) ; +#78408 = EDGE_CURVE ( 'NONE', #9766, #88616, #24486, .T. ) ; +#78409 = EDGE_LOOP ( 'NONE', ( #58859, #63949, #12916, #41015 ) ) ; +#78410 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.000000000000000000, 0.000000000000000000 ) ) ; +#78411 = EDGE_LOOP ( 'NONE', ( #85592, #34024, #58014, #77262, #85318, #73495, #6661, #49070 ) ) ; +#78412 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78413 = CARTESIAN_POINT ( 'NONE', ( -0.09183755801571232003, -1.507352529807550079, 0.8100000000000000533 ) ) ; +#78414 = STYLED_ITEM ( 'NONE', ( #71206 ), #65611 ) ; +#78415 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220045297, -1.500000000000000000, 0.000000000000000000 ) ) ; +#78416 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78417 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8991599999999999593 ) ) ; +#78418 = FILL_AREA_STYLE ('',( #47270 ) ) ; +#78419 = VECTOR ( 'NONE', #92511, 1000.000000000000000 ) ; +#78420 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37696 ), #34436 ) ; +#78421 = EDGE_LOOP ( 'NONE', ( #73117, #76133, #88731, #3295 ) ) ; +#78422 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91603, 'distance_accuracy_value', 'NONE'); +#78423 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#78424 = SURFACE_STYLE_USAGE ( .BOTH. , #52953 ) ; +#78425 = SURFACE_STYLE_FILL_AREA ( #41657 ) ; +#78426 = VERTEX_POINT ( 'NONE', #84713 ) ; +#78427 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#78428 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#78429 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23268, #40099, #86041, #8346, #85536, #77361, #39584, #40611 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000002776, 0.5000000000000004441, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#78430 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78431 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000002125, 0.8991599999999999593 ) ) ; +#78432 = AXIS2_PLACEMENT_3D ( 'NONE', #78613, #30478, #39687 ) ; +#78433 = EDGE_LOOP ( 'NONE', ( #23980, #3369, #57960, #5798 ) ) ; +#78435 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#78434 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78436 = VERTEX_POINT ( 'NONE', #14727 ) ; +#78437 = EDGE_LOOP ( 'NONE', ( #35306, #49940, #80233, #28997 ) ) ; +#78438 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78439 = SURFACE_STYLE_USAGE ( .BOTH. , #8402 ) ; +#78440 = LINE ( 'NONE', #62148, #81574 ) ; +#78441 = EDGE_LOOP ( 'NONE', ( #17992, #67042, #69322, #66082 ) ) ; +#78442 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#78443 = EDGE_CURVE ( 'NONE', #71133, #36233, #30554, .T. ) ; +#78444 = SURFACE_STYLE_FILL_AREA ( #39140 ) ; +#78445 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#78446 = VERTEX_POINT ( 'NONE', #55119 ) ; +#78448 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, -0.02000000000000000042 ) ) ; +#78447 = SURFACE_SIDE_STYLE ('',( #61145 ) ) ; +#78449 = DIRECTION ( 'NONE', ( -2.824738166141190008E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78450 = ORIENTED_EDGE ( 'NONE', *, *, #46139, .T. ) ; +#78451 = ORIENTED_EDGE ( 'NONE', *, *, #22738, .T. ) ; +#78452 = PRESENTATION_STYLE_ASSIGNMENT (( #72296 ) ) ; +#78453 = SURFACE_SIDE_STYLE ('',( #87134 ) ) ; +#78454 = CARTESIAN_POINT ( 'NONE', ( -1.073952997185251501, -0.9562692539047544793, 0.8100000000000201483 ) ) ; +#78455 = ADVANCED_FACE ( 'NONE', ( #31600 ), #62766, .T. ) ; +#78456 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#78457 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45827 ) ) ; +#78458 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#78459 = FACE_OUTER_BOUND ( 'NONE', #99924, .T. ) ; +#78460 = CARTESIAN_POINT ( 'NONE', ( -0.04176633354695089700, -1.139163918933580266, 0.8299999999999999600 ) ) ; +#78461 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100952 ) ; +#78462 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, 0.2999999999999999889 ) ) ; +#78463 = EDGE_CURVE ( 'NONE', #85319, #87763, #71930, .T. ) ; +#78464 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78465 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#78466 = ORIENTED_EDGE ( 'NONE', *, *, #77738, .F. ) ; +#78467 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#78469 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78468 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78471 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -3.500000000000000444, 0.000000000000000000 ) ) ; +#78470 = AXIS2_PLACEMENT_3D ( 'NONE', #78088, #29599, #30575 ) ; +#78472 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#78473 = VECTOR ( 'NONE', #47582, 1000.000000000000000 ) ; +#78474 = CARTESIAN_POINT ( 'NONE', ( -1.850000000000000311, 3.099999999999994316, 0.000000000000000000 ) ) ; +#78475 = FACE_OUTER_BOUND ( 'NONE', #96346, .T. ) ; +#78476 = ORIENTED_EDGE ( 'NONE', *, *, #100048, .F. ) ; +#78477 = SURFACE_STYLE_USAGE ( .BOTH. , #18175 ) ; +#78478 = FILL_AREA_STYLE_COLOUR ( '', #41992 ) ; +#78479 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#78480 = FILL_AREA_STYLE ('',( #67788 ) ) ; +#78481 = PLANE ( 'NONE', #93877 ) ; +#78482 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.700000000000000178, 0.000000000000000000 ) ) ; +#78483 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#78484 = DIRECTION ( 'NONE', ( -0.3444045651374270656, 0.000000000000000000, -0.9388213331153589802 ) ) ; +#78485 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78486 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#78487 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78488 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.000000000000000000 ) ) ; +#78489 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.1000000000000000056, -13.40000000000000036 ) ) ; +#78490 = FILL_AREA_STYLE_COLOUR ( '', #43096 ) ; +#78491 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65437 ) ) ; +#78492 = SURFACE_SIDE_STYLE ('',( #16177 ) ) ; +#78493 = SURFACE_SIDE_STYLE ('',( #16179 ) ) ; +#78494 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78496 = EDGE_CURVE ( 'NONE', #81623, #28287, #41793, .T. ) ; +#78495 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8648700000000000276 ) ) ; +#78497 = LINE ( 'NONE', #78007, #94825 ) ; +#78498 = ORIENTED_EDGE ( 'NONE', *, *, #31865, .T. ) ; +#78499 = FILL_AREA_STYLE_COLOUR ( '', #6838 ) ; +#78500 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78501 = FILL_AREA_STYLE_COLOUR ( '', #85169 ) ; +#78502 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78503 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8099999999999815126 ) ) ; +#78504 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85059 ), #59092 ) ; +#78505 = LINE ( 'NONE', #24426, #98226 ) ; +#78506 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#78507 = ORIENTED_EDGE ( 'NONE', *, *, #11884, .F. ) ; +#78508 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78509 = FILL_AREA_STYLE_COLOUR ( '', #31777 ) ; +#78510 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78511 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#78512 = EDGE_CURVE ( 'NONE', #25848, #96933, #56636, .T. ) ; +#78513 = ORIENTED_EDGE ( 'NONE', *, *, #65139, .T. ) ; +#78514 = ORIENTED_EDGE ( 'NONE', *, *, #65298, .F. ) ; +#78515 = VECTOR ( 'NONE', #31067, 1000.000000000000000 ) ; +#78516 = FACE_OUTER_BOUND ( 'NONE', #73576, .T. ) ; +#78517 = EDGE_LOOP ( 'NONE', ( #94202, #53666, #20026, #71625 ) ) ; +#78518 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78519 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#78520 = EDGE_CURVE ( 'NONE', #52774, #7082, #72402, .T. ) ; +#78521 = LINE ( 'NONE', #30519, #28788 ) ; +#78522 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78523 = FACE_OUTER_BOUND ( 'NONE', #97031, .T. ) ; +#78524 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18152 ), #45835 ) ; +#78525 = AXIS2_PLACEMENT_3D ( 'NONE', #97663, #27792, #90037 ) ; +#78526 = SHAPE_DEFINITION_REPRESENTATION ( #45765, #37058 ) ; +#78527 = SURFACE_STYLE_FILL_AREA ( #34124 ) ; +#78528 = LINE ( 'NONE', #53057, #78343 ) ; +#78530 = ORIENTED_EDGE ( 'NONE', *, *, #64391, .F. ) ; +#78529 = VERTEX_POINT ( 'NONE', #57646 ) ; +#78531 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14582, #98316, #44734 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78532 = EDGE_LOOP ( 'NONE', ( #32184, #34254, #100052, #8009 ) ) ; +#78533 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886600000000008, 0.8991599999999999593 ) ) ; +#78534 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12214, 'distance_accuracy_value', 'NONE'); +#78535 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78537 = ORIENTED_EDGE ( 'NONE', *, *, #26595, .F. ) ; +#78538 = ADVANCED_FACE ( 'NONE', ( #80105 ), #49975, .F. ) ; +#78539 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61681 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11291, #63521, #94609 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78540 = EDGE_CURVE ( 'NONE', #38918, #34152, #64759, .T. ) ; +#78541 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999999944, 0.1400000000000004297 ) ) ; +#78542 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78544 = FILL_AREA_STYLE ('',( #86205 ) ) ; +#78543 = FACE_OUTER_BOUND ( 'NONE', #81697, .T. ) ; +#78545 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1968 ) ) ; +#78546 = VERTEX_POINT ( 'NONE', #79593 ) ; +#78547 = FILL_AREA_STYLE_COLOUR ( '', #71561 ) ; +#78548 = ORIENTED_EDGE ( 'NONE', *, *, #35776, .F. ) ; +#78549 = ORIENTED_EDGE ( 'NONE', *, *, #54888, .T. ) ; +#78550 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#78551 = MANIFOLD_SOLID_BREP ( 'ÊäÈë44', #76175 ) ; +#78552 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8426 ) ) ; +#78554 = ORIENTED_EDGE ( 'NONE', *, *, #7396, .T. ) ; +#78553 = PLANE ( 'NONE', #60857 ) ; +#78555 = LINE ( 'NONE', #62263, #44929 ) ; +#78556 = EDGE_CURVE ( 'NONE', #45083, #80846, #40788, .T. ) ; +#78557 = SURFACE_STYLE_USAGE ( .BOTH. , #78073 ) ; +#78558 = PRESENTATION_STYLE_ASSIGNMENT (( #39773 ) ) ; +#78559 = ORIENTED_EDGE ( 'NONE', *, *, #12054, .F. ) ; +#78560 = FILL_AREA_STYLE_COLOUR ( '', #59908 ) ; +#78562 = ORIENTED_EDGE ( 'NONE', *, *, #45515, .F. ) ; +#78561 = VECTOR ( 'NONE', #72616, 1000.000000000000000 ) ; +#78563 = ORIENTED_EDGE ( 'NONE', *, *, #55604, .F. ) ; +#78564 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78565 = CARTESIAN_POINT ( 'NONE', ( 1.823289888948260051, -1.336414498567920051, 0.8300000000000002931 ) ) ; +#78566 = AXIS2_PLACEMENT_3D ( 'NONE', #248, #94159, #24279 ) ; +#78567 = CARTESIAN_POINT ( 'NONE', ( -0.4703841191077399730, -1.247659769119729978, 0.8100000000000000533 ) ) ; +#78568 = VECTOR ( 'NONE', #96989, 1000.000000000000000 ) ; +#78569 = LINE ( 'NONE', #80126, #84695 ) ; +#78570 = EDGE_CURVE ( 'NONE', #90959, #69132, #19132, .T. ) ; +#78571 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24796, 'distance_accuracy_value', 'NONE'); +#78572 = VERTEX_POINT ( 'NONE', #83103 ) ; +#78573 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#78574 = LINE ( 'NONE', #7040, #28353 ) ; +#78575 = EDGE_LOOP ( 'NONE', ( #81964, #32318, #27202, #43466 ) ) ; +#78576 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14532 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75281, #14439, #84430 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78577 = SURFACE_STYLE_FILL_AREA ( #8545 ) ; +#78578 = CARTESIAN_POINT ( 'NONE', ( -0.4613015463790179349, -1.014418990859363046, 0.8299999999999998490 ) ) ; +#78579 = SURFACE_STYLE_USAGE ( .BOTH. , #471 ) ; +#78581 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78580 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2808578643762690841, -0.1434314575050761598 ) ) ; +#78582 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#78583 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#78584 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#78585 = PRESENTATION_STYLE_ASSIGNMENT (( #48994 ) ) ; +#78586 = PRESENTATION_STYLE_ASSIGNMENT (( #2010 ) ) ; +#78588 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58599 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50870, #43672, #51373 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78587 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#78589 = SURFACE_STYLE_FILL_AREA ( #94897 ) ; +#78590 = SURFACE_SIDE_STYLE ('',( #93378 ) ) ; +#78591 = EDGE_CURVE ( 'NONE', #61494, #88860, #3979, .T. ) ; +#78592 = PRESENTATION_STYLE_ASSIGNMENT (( #47462 ) ) ; +#78593 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#78594 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75883 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52362, #81524, #5825 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78595 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#78596 = AXIS2_PLACEMENT_3D ( 'NONE', #15158, #29522, #30487 ) ; +#78597 = ADVANCED_FACE ( 'NONE', ( #19289 ), #43279, .F. ) ; +#78598 = CARTESIAN_POINT ( 'NONE', ( 5.257674999999999876, 8.519819000000000031, 0.8991599999999999593 ) ) ; +#78599 = FILL_AREA_STYLE ('',( #61312 ) ) ; +#78600 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78601 = STYLED_ITEM ( 'NONE', ( #81363 ), #59296 ) ; +#78602 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78603 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78604 = AXIS2_PLACEMENT_3D ( 'NONE', #54114, #15262, #15786 ) ; +#78605 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48804 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32481, #17627, #24333 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78606 = VERTEX_POINT ( 'NONE', #52464 ) ; +#78607 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.000000000000000000 ) ) ; +#78609 = EDGE_CURVE ( 'NONE', #88552, #48839, #44268, .T. ) ; +#78608 = PRESENTATION_STYLE_ASSIGNMENT (( #48515 ) ) ; +#78610 = CIRCLE ( 'NONE', #14940, 0.009999999999999998473 ) ; +#78611 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32043, 'distance_accuracy_value', 'NONE'); +#78612 = EDGE_LOOP ( 'NONE', ( #30501, #76445, #1085, #94176 ) ) ; +#78614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32425, 'distance_accuracy_value', 'NONE'); +#78613 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#78615 = FILL_AREA_STYLE ('',( #94427 ) ) ; +#78616 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78617 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#78618 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92044 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19752, #89197, #19223 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78619 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#78620 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#78621 = AXIS2_PLACEMENT_3D ( 'NONE', #95060, #46594, #85407 ) ; +#78622 = ORIENTED_EDGE ( 'NONE', *, *, #86355, .F. ) ; +#78623 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -0.9701298701298698424, 0.8299999999999999600 ) ) ; +#78624 = ORIENTED_EDGE ( 'NONE', *, *, #91471, .T. ) ; +#78625 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90003 ), #54148 ) ; +#78626 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68191, 'distance_accuracy_value', 'NONE'); +#78627 = PRESENTATION_STYLE_ASSIGNMENT (( #92422 ) ) ; +#78628 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#78629 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78630 = SURFACE_STYLE_USAGE ( .BOTH. , #25550 ) ; +#78631 = SURFACE_STYLE_USAGE ( .BOTH. , #16316 ) ; +#78632 = PRESENTATION_STYLE_ASSIGNMENT (( #93912 ) ) ; +#78633 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13403 ), #42795 ) ; +#78634 = VERTEX_POINT ( 'NONE', #67747 ) ; +#78635 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#78636 = CARTESIAN_POINT ( 'NONE', ( 10.94988375024997573, 8.003630750249975279, 0.8991599999999999593 ) ) ; +#78637 = ORIENTED_EDGE ( 'NONE', *, *, #42813, .F. ) ; +#78638 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#78639 = LINE ( 'NONE', #23034, #50142 ) ; +#78640 = ORIENTED_EDGE ( 'NONE', *, *, #30927, .T. ) ; +#78641 = FACE_OUTER_BOUND ( 'NONE', #17232, .T. ) ; +#78642 = EDGE_CURVE ( 'NONE', #95595, #59144, #53339, .T. ) ; +#78643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78644 = LINE ( 'NONE', #28793, #30225 ) ; +#78645 = LINE ( 'NONE', #94460, #56129 ) ; +#78646 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#78647 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8648700000000000276 ) ) ; +#78649 = EDGE_LOOP ( 'NONE', ( #83316, #4561, #58378, #54691 ) ) ; +#78648 = ORIENTED_EDGE ( 'NONE', *, *, #4382, .T. ) ; +#78650 = AXIS2_PLACEMENT_3D ( 'NONE', #77909, #76394, #6395 ) ; +#78651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6775 ) ) ; +#78652 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78653 = FILL_AREA_STYLE_COLOUR ( '', #72433 ) ; +#78654 = VERTEX_POINT ( 'NONE', #74446 ) ; +#78655 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21588 ), #13582 ) ; +#78656 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#78657 = ORIENTED_EDGE ( 'NONE', *, *, #63980, .F. ) ; +#78658 = EDGE_CURVE ( 'NONE', #21395, #64323, #66756, .T. ) ; +#78659 = EDGE_LOOP ( 'NONE', ( #18391, #42617, #28545, #93097 ) ) ; +#78660 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999989875, 0.000000000000000000 ) ) ; +#78661 = AXIS2_PLACEMENT_3D ( 'NONE', #63561, #33928, #16533 ) ; +#78662 = AXIS2_PLACEMENT_3D ( 'NONE', #31370, #93610, #23730 ) ; +#78663 = SURFACE_STYLE_USAGE ( .BOTH. , #7624 ) ; +#78664 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#78665 = SURFACE_SIDE_STYLE ('',( #47 ) ) ; +#78666 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#78667 = ORIENTED_EDGE ( 'NONE', *, *, #52503, .T. ) ; +#78668 = ADVANCED_FACE ( 'NONE', ( #27993 ), #59156, .T. ) ; +#78669 = ORIENTED_EDGE ( 'NONE', *, *, #98320, .F. ) ; +#78670 = FILL_AREA_STYLE ('',( #60874 ) ) ; +#78671 = ORIENTED_EDGE ( 'NONE', *, *, #88639, .T. ) ; +#78672 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78673 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#78674 = FILL_AREA_STYLE_COLOUR ( '', #72107 ) ; +#78675 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8472 ), #47703 ) ; +#78676 = EDGE_LOOP ( 'NONE', ( #51054, #30534, #47029, #5904 ) ) ; +#78677 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52619 ), #99768 ) ; +#78678 = PRESENTATION_STYLE_ASSIGNMENT (( #71032 ) ) ; +#78679 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61093 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66129, #27333, #50350 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78680 = CARTESIAN_POINT ( 'NONE', ( 1.865911170909900108, -1.438073744133560039, 0.8099999999999996092 ) ) ; +#78681 = ORIENTED_EDGE ( 'NONE', *, *, #47030, .T. ) ; +#78682 = PRESENTATION_STYLE_ASSIGNMENT (( #66 ) ) ; +#78683 = VERTEX_POINT ( 'NONE', #61140 ) ; +#78684 = VECTOR ( 'NONE', #37169, 1000.000000000000000 ) ; +#78685 = EDGE_CURVE ( 'NONE', #54748, #44962, #62152, .T. ) ; +#78686 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78687 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78688 = FACE_OUTER_BOUND ( 'NONE', #42186, .T. ) ; +#78689 = AXIS2_PLACEMENT_3D ( 'NONE', #17463, #80296, #63483 ) ; +#78690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78692 = EDGE_LOOP ( 'NONE', ( #66735, #57938, #39634, #28015 ) ) ; +#78691 = FILL_AREA_STYLE_COLOUR ( '', #55887 ) ; +#78693 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -9.789044574937121152E-17, -0.8499999999999999778 ) ) ; +#78694 = CARTESIAN_POINT ( 'NONE', ( -0.7486876120449306171, 1.376287671486964070, 0.8100000000000000533 ) ) ; +#78695 = ADVANCED_FACE ( 'NONE', ( #21802 ), #93217, .T. ) ; +#78697 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8991599999999999593 ) ) ; +#78696 = CARTESIAN_POINT ( 'NONE', ( -3.200000000000000178, 3.000000000000000000, 0.8299999999999999600 ) ) ; +#78698 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9238200612200859752, -0.02000000000000000042 ) ) ; +#78699 = LINE ( 'NONE', #32759, #83297 ) ; +#78700 = EDGE_CURVE ( 'NONE', #56990, #61177, #76939, .T. ) ; +#78701 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#78702 = VERTEX_POINT ( 'NONE', #31480 ) ; +#78703 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78704 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 3.435721000000000025, 0.8991599999999999593 ) ) ; +#78705 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#78706 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#78707 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78708 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#78709 = AXIS2_PLACEMENT_3D ( 'NONE', #83884, #39415, #13875 ) ; +#78710 = STYLED_ITEM ( 'NONE', ( #32052 ), #52228 ) ; +#78711 = PRESENTATION_STYLE_ASSIGNMENT (( #46552 ) ) ; +#78712 = ORIENTED_EDGE ( 'NONE', *, *, #80327, .T. ) ; +#78713 = PRESENTATION_STYLE_ASSIGNMENT (( #33289 ) ) ; +#78714 = EDGE_LOOP ( 'NONE', ( #2703, #45355, #70483, #65751 ) ) ; +#78715 = EDGE_CURVE ( 'NONE', #100590, #51457, #93716, .T. ) ; +#78717 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 2.311421000000000170, 0.8991599999999999593 ) ) ; +#78716 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86905 ), #11804 ) ; +#78718 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.5000000000000000000, 0.000000000000000000 ) ) ; +#78719 = MANIFOLD_SOLID_BREP ( 'ÊäÈë165', #81095 ) ; +#78720 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#78721 = SURFACE_SIDE_STYLE ('',( #100568 ) ) ; +#78722 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41229 ) ) ; +#78723 = VECTOR ( 'NONE', #14773, 1000.000000000000000 ) ; +#78724 = LINE ( 'NONE', #8693, #64090 ) ; +#78725 = ORIENTED_EDGE ( 'NONE', *, *, #23473, .F. ) ; +#78726 = CARTESIAN_POINT ( 'NONE', ( 1.750951194234720010, -0.9053603395923379704, 0.8100000000000008304 ) ) ; +#78727 = ADVANCED_FACE ( 'NONE', ( #94241 ), #99328, .T. ) ; +#78728 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78729 = PLANE ( 'NONE', #67358 ) ; +#78730 = VECTOR ( 'NONE', #294, 1000.000000000000000 ) ; +#78731 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78732 = STYLED_ITEM ( 'NONE', ( #50147 ), #18929 ) ; +#78733 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21676 ) ) ; +#78734 = FILL_AREA_STYLE_COLOUR ( '', #24155 ) ; +#78735 = FILL_AREA_STYLE_COLOUR ( '', #56407 ) ; +#78736 = SURFACE_STYLE_FILL_AREA ( #7696 ) ; +#78737 = ADVANCED_FACE ( 'NONE', ( #94745 ), #41677, .T. ) ; +#78738 = FILL_AREA_STYLE ('',( #17938 ) ) ; +#78739 = LINE ( 'NONE', #85896, #17529 ) ; +#78740 = CARTESIAN_POINT ( 'NONE', ( 0.01806955754146100102, -0.9394184040112210088, 0.8299999999999999600 ) ) ; +#78741 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91363, 'distance_accuracy_value', 'NONE'); +#78742 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60807 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88952, #50180, #89453 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78743 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#78744 = ORIENTED_EDGE ( 'NONE', *, *, #54749, .T. ) ; +#78745 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#78746 = EDGE_CURVE ( 'NONE', #97015, #75181, #2871, .T. ) ; +#78748 = EDGE_LOOP ( 'NONE', ( #93537, #79548, #42367 ) ) ; +#78747 = AXIS2_PLACEMENT_3D ( 'NONE', #29098, #35778, #36758 ) ; +#78749 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92303, 'distance_accuracy_value', 'NONE'); +#78750 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92400, 'distance_accuracy_value', 'NONE'); +#78751 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96727 ), #21756 ) ; +#78752 = FACE_OUTER_BOUND ( 'NONE', #83563, .T. ) ; +#78753 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78754 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78755 = SURFACE_STYLE_USAGE ( .BOTH. , #47620 ) ; +#78756 = STYLED_ITEM ( 'NONE', ( #26221 ), #11272 ) ; +#78757 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78758 = CARTESIAN_POINT ( 'NONE', ( -0.008589415658712419230, -1.182875588085640306, 0.8299999999999999600 ) ) ; +#78759 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78760 = FILL_AREA_STYLE ('',( #24167 ) ) ; +#78761 = EDGE_LOOP ( 'NONE', ( #48620, #66812, #66986, #8790, #23949, #24797 ) ) ; +#78762 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#78763 = SURFACE_STYLE_FILL_AREA ( #86432 ) ; +#78764 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78765 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37907, 'distance_accuracy_value', 'NONE'); +#78766 = PLANE ( 'NONE', #72095 ) ; +#78767 = VERTEX_POINT ( 'NONE', #9432 ) ; +#78768 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#78769 = VERTEX_POINT ( 'NONE', #55504 ) ; +#78770 = EDGE_CURVE ( 'NONE', #10994, #97934, #87121, .T. ) ; +#78771 = ADVANCED_FACE ( 'NONE', ( #32998 ), #3371, .T. ) ; +#78772 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78773 = FILL_AREA_STYLE ('',( #31301 ) ) ; +#78774 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#78775 = LINE ( 'NONE', #40504, #35206 ) ; +#78776 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, 0.000000000000000000 ) ) ; +#78778 = VERTEX_POINT ( 'NONE', #50850 ) ; +#78777 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78779 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#78780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78781 = PRESENTATION_STYLE_ASSIGNMENT (( #1709 ) ) ; +#78782 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #44412, #75582, #45399, #5588 ), + ( #79631, #7549, #79118, #48490 ), + ( #93370, #31128, #78580, #24001 ), + ( #47453, #25015, #15256, #94888 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#78783 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78784 = EDGE_CURVE ( 'NONE', #16240, #42663, #34536, .T. ) ; +#78785 = ORIENTED_EDGE ( 'NONE', *, *, #84392, .F. ) ; +#78786 = ADVANCED_FACE ( 'NONE', ( #81508 ), #66149, .T. ) ; +#78787 = SURFACE_SIDE_STYLE ('',( #76770 ) ) ; +#78788 = SURFACE_STYLE_FILL_AREA ( #33868 ) ; +#78789 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31491 ) ) ; +#78790 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78791 = PRESENTATION_STYLE_ASSIGNMENT (( #100147 ) ) ; +#78792 = ORIENTED_EDGE ( 'NONE', *, *, #60780, .F. ) ; +#78793 = EDGE_CURVE ( 'NONE', #98364, #88828, #67138, .T. ) ; +#78794 = VERTEX_POINT ( 'NONE', #59546 ) ; +#78795 = ORIENTED_EDGE ( 'NONE', *, *, #84999, .T. ) ; +#78796 = SURFACE_STYLE_USAGE ( .BOTH. , #100272 ) ; +#78797 = STYLED_ITEM ( 'NONE', ( #89530 ), #76147 ) ; +#78798 = ORIENTED_EDGE ( 'NONE', *, *, #75832, .F. ) ; +#78800 = ORIENTED_EDGE ( 'NONE', *, *, #13345, .T. ) ; +#78799 = SURFACE_SIDE_STYLE ('',( #86469 ) ) ; +#78801 = ADVANCED_FACE ( 'NONE', ( #20674 ), #51848, .T. ) ; +#78803 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, -0.02000000000001050243 ) ) ; +#78802 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78804 = SURFACE_SIDE_STYLE ('',( #49716 ) ) ; +#78805 = ORIENTED_EDGE ( 'NONE', *, *, #59022, .T. ) ; +#78806 = FILL_AREA_STYLE_COLOUR ( '', #30859 ) ; +#78808 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#78807 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78809 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#78810 = ORIENTED_EDGE ( 'NONE', *, *, #14370, .T. ) ; +#78811 = ADVANCED_FACE ( 'NONE', ( #69100 ), #92600, .F. ) ; +#78812 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78813 = VECTOR ( 'NONE', #1512, 1000.000000000000000 ) ; +#78814 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78815 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80517 ) ) ; +#78816 = PLANE ( 'NONE', #48358 ) ; +#78817 = VERTEX_POINT ( 'NONE', #62025 ) ; +#78819 = FILL_AREA_STYLE_COLOUR ( '', #79616 ) ; +#78818 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8648700000000000276 ) ) ; +#78820 = VERTEX_POINT ( 'NONE', #93096 ) ; +#78821 = STYLED_ITEM ( 'NONE', ( #76441 ), #60829 ) ; +#78822 = SURFACE_SIDE_STYLE ('',( #44757 ) ) ; +#78823 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87001 ) ) ; +#78824 = EDGE_CURVE ( 'NONE', #25989, #86105, #45135, .T. ) ; +#78825 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78827 = EDGE_CURVE ( 'NONE', #9248, #7028, #87324, .T. ) ; +#78826 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78828 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22162 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45251, #1744, #49729 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78829 = STYLED_ITEM ( 'NONE', ( #5224 ), #9541 ) ; +#78830 = LINE ( 'NONE', #78338, #69501 ) ; +#78831 = VECTOR ( 'NONE', #58642, 1000.000000000000000 ) ; +#78832 = ORIENTED_EDGE ( 'NONE', *, *, #78700, .T. ) ; +#78833 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#78834 = FILL_AREA_STYLE_COLOUR ( '', #42615 ) ; +#78835 = SURFACE_STYLE_USAGE ( .BOTH. , #55389 ) ; +#78836 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78837 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100123, 'distance_accuracy_value', 'NONE'); +#78838 = CARTESIAN_POINT ( 'NONE', ( -1.032372237264020054, -0.9101533448649530289, 0.8100000000000000533 ) ) ; +#78839 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#78840 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959499, 1.048695503451053346E-76 ) ) ; +#78841 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#78842 = CYLINDRICAL_SURFACE ( 'NONE', #24312, 0.05000000000000012768 ) ; +#78843 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#78844 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.4600000000000000200, 0.8000000000000001554 ) ) ; +#78845 = PRESENTATION_STYLE_ASSIGNMENT (( #79875 ) ) ; +#78846 = EDGE_LOOP ( 'NONE', ( #60398, #76535, #56284, #19908 ) ) ; +#78847 = CARTESIAN_POINT ( 'NONE', ( -1.016236428037849970, -1.189797473215369994, 0.8300000000000002931 ) ) ; +#78848 = EDGE_CURVE ( 'NONE', #30792, #78282, #93591, .T. ) ; +#78849 = STYLED_ITEM ( 'NONE', ( #48349 ), #70970 ) ; +#78851 = PRESENTATION_STYLE_ASSIGNMENT (( #95144 ) ) ; +#78850 = PLANE ( 'NONE', #2362 ) ; +#78852 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662330114, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#78853 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78854 = FILL_AREA_STYLE ('',( #94140 ) ) ; +#78855 = AXIS2_PLACEMENT_3D ( 'NONE', #11760, #27203, #89474 ) ; +#78856 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78857 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#78858 = VERTEX_POINT ( 'NONE', #54869 ) ; +#78859 = EDGE_CURVE ( 'NONE', #53705, #64307, #61017, .T. ) ; +#78860 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#78861 = FILL_AREA_STYLE ('',( #1251 ) ) ; +#78862 = VECTOR ( 'NONE', #26256, 1000.000000000000000 ) ; +#78863 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#78864 = PRESENTATION_STYLE_ASSIGNMENT (( #46169 ) ) ; +#78865 = FILL_AREA_STYLE_COLOUR ( '', #100189 ) ; +#78866 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.500000000000000444, 0.000000000000000000 ) ) ; +#78867 = EDGE_CURVE ( 'NONE', #70649, #74502, #85981, .T. ) ; +#78868 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78869 = VECTOR ( 'NONE', #85404, 1000.000000000000000 ) ; +#78870 = VECTOR ( 'NONE', #63862, 1000.000000000000000 ) ; +#78871 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78872 = CARTESIAN_POINT ( 'NONE', ( 1.039609075668130211, -1.335706927508150121, 0.8299999999999999600 ) ) ; +#78873 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#78874 = SURFACE_STYLE_USAGE ( .BOTH. , #62580 ) ; +#78875 = VECTOR ( 'NONE', #82748, 1000.000000000000000 ) ; +#78876 = LINE ( 'NONE', #87050, #51995 ) ; +#78877 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#78878 = EDGE_LOOP ( 'NONE', ( #97553, #59448, #6905, #21562 ) ) ; +#78879 = SURFACE_STYLE_FILL_AREA ( #16558 ) ; +#78880 = EDGE_CURVE ( 'NONE', #73519, #43154, #70659, .T. ) ; +#78881 = ORIENTED_EDGE ( 'NONE', *, *, #89539, .F. ) ; +#78882 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42781, 'distance_accuracy_value', 'NONE'); +#78883 = SURFACE_STYLE_FILL_AREA ( #40088 ) ; +#78884 = PRESENTATION_STYLE_ASSIGNMENT (( #93649 ) ) ; +#78885 = CARTESIAN_POINT ( 'NONE', ( 0.1743057588777000011, -1.390658178011239920, 0.8299999999999999600 ) ) ; +#78886 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78887 = VECTOR ( 'NONE', #65305, 1000.000000000000000 ) ; +#78888 = SURFACE_STYLE_USAGE ( .BOTH. , #23770 ) ; +#78889 = PRESENTATION_STYLE_ASSIGNMENT (( #54928 ) ) ; +#78890 = SURFACE_STYLE_FILL_AREA ( #30905 ) ; +#78891 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#78892 = VERTEX_POINT ( 'NONE', #47686 ) ; +#78893 = FILL_AREA_STYLE ('',( #25799 ) ) ; +#78894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2373, 'distance_accuracy_value', 'NONE'); +#78895 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99229, #29380, #35566 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#78896 = AXIS2_PLACEMENT_3D ( 'NONE', #30468, #31511, #15134 ) ; +#78897 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78898 = EDGE_LOOP ( 'NONE', ( #13655, #99794, #67452, #17753 ) ) ; +#78899 = EDGE_CURVE ( 'NONE', #44500, #30580, #78830, .T. ) ; +#78900 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78901 = EDGE_CURVE ( 'NONE', #66922, #1733, #64198, .T. ) ; +#78902 = VECTOR ( 'NONE', #66594, 1000.000000000000000 ) ; +#78903 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.299999999999999822, 0.1829999999999499805 ) ) ; +#78904 = MANIFOLD_SOLID_BREP ( 'ÊäÈë64', #58445 ) ; +#78905 = EDGE_LOOP ( 'NONE', ( #47672, #83719, #1644, #75511 ) ) ; +#78906 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78907 = ADVANCED_FACE ( 'N', ( #95124 ), #16507, .T. ) ; +#78908 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9912, 'distance_accuracy_value', 'NONE'); +#78909 = AXIS2_PLACEMENT_3D ( 'NONE', #91615, #68627, #54346 ) ; +#78910 = LINE ( 'NONE', #40123, #68654 ) ; +#78911 = ORIENTED_EDGE ( 'NONE', *, *, #73830, .T. ) ; +#78912 = EDGE_CURVE ( 'NONE', #25185, #23706, #80362, .T. ) ; +#78913 = FILL_AREA_STYLE_COLOUR ( '', #85539 ) ; +#78914 = VECTOR ( 'NONE', #62863, 1000.000000000000000 ) ; +#78915 = ORIENTED_EDGE ( 'NONE', *, *, #90775, .F. ) ; +#78916 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#78917 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#78919 = EDGE_CURVE ( 'NONE', #99420, #71585, #8292, .T. ) ; +#78918 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78920 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78921 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #63198, #82894 ) ; +#78922 = AXIS2_PLACEMENT_3D ( 'NONE', #51625, #36291, #13724 ) ; +#78923 = EDGE_LOOP ( 'NONE', ( #58274, #48604, #78328, #48683 ) ) ; +#78924 = FILL_AREA_STYLE ('',( #55978 ) ) ; +#78925 = FACE_OUTER_BOUND ( 'NONE', #87877, .T. ) ; +#78926 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#78927 = VECTOR ( 'NONE', #57746, 1000.000000000000000 ) ; +#78928 = SURFACE_STYLE_USAGE ( .BOTH. , #47793 ) ; +#78929 = ORIENTED_EDGE ( 'NONE', *, *, #15675, .F. ) ; +#78930 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#78931 = LINE ( 'NONE', #8899, #70242 ) ; +#78932 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#78933 = VECTOR ( 'NONE', #34189, 1000.000000000000000 ) ; +#78934 = EDGE_LOOP ( 'NONE', ( #71031, #76948, #76396, #88994 ) ) ; +#78935 = FACE_OUTER_BOUND ( 'NONE', #69294, .T. ) ; +#78936 = EDGE_LOOP ( 'NONE', ( #1935, #21011, #6161, #32409, #8260, #3753 ) ) ; +#78937 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21871 ) ) ; +#78938 = ORIENTED_EDGE ( 'NONE', *, *, #9937, .F. ) ; +#78939 = LINE ( 'NONE', #63653, #1055 ) ; +#78940 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#78941 = STYLED_ITEM ( 'NONE', ( #62049 ), #76759 ) ; +#78942 = STYLED_ITEM ( 'NONE', ( #16200 ), #25905 ) ; +#78944 = EDGE_CURVE ( 'NONE', #100744, #96313, #94718, .T. ) ; +#78943 = SURFACE_SIDE_STYLE ('',( #47807 ) ) ; +#78945 = EDGE_LOOP ( 'NONE', ( #91462, #72493, #45563, #35504, #48684, #63960 ) ) ; +#78946 = FILL_AREA_STYLE_COLOUR ( '', #15635 ) ; +#78947 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#78948 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41664 ), #16982 ) ; +#78949 = CARTESIAN_POINT ( 'NONE', ( 2.523820061220085176, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#78950 = AXIS2_PLACEMENT_3D ( 'NONE', #49901, #50421, #2918 ) ; +#78951 = ORIENTED_EDGE ( 'NONE', *, *, #13639, .F. ) ; +#78952 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#78953 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#78954 = ORIENTED_EDGE ( 'NONE', *, *, #851, .T. ) ; +#78955 = ORIENTED_EDGE ( 'NONE', *, *, #12665, .T. ) ; +#78956 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78957 = LINE ( 'NONE', #64649, #71843 ) ; +#78958 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999467, -3.149999999999999911, 0.000000000000000000 ) ) ; +#78959 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#78960 = SURFACE_SIDE_STYLE ('',( #847 ) ) ; +#78962 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#78961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11966 ), #67495 ) ; +#78963 = CARTESIAN_POINT ( 'NONE', ( -0.5053774350649350433, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#78964 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#78965 = VECTOR ( 'NONE', #33914, 1000.000000000000000 ) ; +#78966 = LINE ( 'NONE', #32525, #36501 ) ; +#78967 = SURFACE_STYLE_FILL_AREA ( #56017 ) ; +#78968 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#78969 = VECTOR ( 'NONE', #87952, 1000.000000000000000 ) ; +#78970 = VECTOR ( 'NONE', #47594, 1000.000000000000000 ) ; +#78971 = VERTEX_POINT ( 'NONE', #17028 ) ; +#78972 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#78973 = EDGE_CURVE ( 'NONE', #52968, #100106, #11310, .T. ) ; +#78975 = FACE_OUTER_BOUND ( 'NONE', #31275, .T. ) ; +#78974 = SURFACE_SIDE_STYLE ('',( #15645 ) ) ; +#78976 = PRESENTATION_STYLE_ASSIGNMENT (( #16151 ) ) ; +#78977 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78978 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#78979 = SURFACE_STYLE_FILL_AREA ( #22853 ) ; +#78980 = LINE ( 'NONE', #52258, #94384 ) ; +#78981 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78982 = LINE ( 'NONE', #40195, #53406 ) ; +#78983 = VECTOR ( 'NONE', #58256, 1000.000000000000114 ) ; +#78984 = CARTESIAN_POINT ( 'NONE', ( 1.987138528525634884, 1.448308458786040198, -11.38289545694101967 ) ) ; +#78985 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#78986 = ORIENTED_EDGE ( 'NONE', *, *, #100275, .T. ) ; +#78987 = ADVANCED_FACE ( 'NONE', ( #19562 ), #90508, .T. ) ; +#78988 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#78989 = SURFACE_STYLE_FILL_AREA ( #17681 ) ; +#78990 = PRESENTATION_STYLE_ASSIGNMENT (( #80513 ) ) ; +#78991 = SURFACE_STYLE_FILL_AREA ( #65176 ) ; +#78992 = SURFACE_STYLE_FILL_AREA ( #71842 ) ; +#78993 = SURFACE_SIDE_STYLE ('',( #55025 ) ) ; +#78994 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44246, 'distance_accuracy_value', 'NONE'); +#78995 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99538, #29196, #69472, #29677 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#78996 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#78997 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.600000000000000089, -11.91999999999999993 ) ) ; +#78998 = SURFACE_SIDE_STYLE ('',( #1396 ) ) ; +#78999 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79000 = PRESENTATION_STYLE_ASSIGNMENT (( #79516 ) ) ; +#79001 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.900000000000000355, 0.000000000000000000 ) ) ; +#79002 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.03429000000000000103 ) ) ; +#79003 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#79004 = FACE_OUTER_BOUND ( 'NONE', #29937, .T. ) ; +#79005 = LINE ( 'NONE', #8967, #44670 ) ; +#79006 = EDGE_CURVE ( 'NONE', #96899, #29025, #50742, .T. ) ; +#79007 = CARTESIAN_POINT ( 'NONE', ( 1.886527894060100019, -1.258231835375339669, 0.8100000000000004974 ) ) ; +#79008 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#79009 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79010 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #59983, 'design' ) ; +#79011 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79012 = ADVANCED_FACE ( 'NONE', ( #26745 ), #5199, .T. ) ; +#79013 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.592200000000000060, 0.8648700000000000276 ) ) ; +#79014 = ORIENTED_EDGE ( 'NONE', *, *, #10146, .F. ) ; +#79015 = SURFACE_SIDE_STYLE ('',( #32565 ) ) ; +#79016 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79017 = FILL_AREA_STYLE_COLOUR ( '', #79523 ) ; +#79018 = STYLED_ITEM ( 'NONE', ( #35883 ), #82162 ) ; +#79019 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26853 ), #95299 ) ; +#79020 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52470, 'distance_accuracy_value', 'NONE'); +#79022 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79021 = LINE ( 'NONE', #1921, #49277 ) ; +#79023 = FILL_AREA_STYLE ('',( #93780 ) ) ; +#79024 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18041 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11298, #27744, #20042 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79025 = EDGE_CURVE ( 'NONE', #44266, #96200, #49736, .T. ) ; +#79026 = ADVANCED_FACE ( 'NONE', ( #19043 ), #65510, .T. ) ; +#79027 = FILL_AREA_STYLE ('',( #32059 ) ) ; +#79028 = LINE ( 'NONE', #25932, #10803 ) ; +#79029 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57455 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95142, #48738, #87027 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79030 = VERTEX_POINT ( 'NONE', #7662 ) ; +#79031 = PLANE ( 'NONE', #12787 ) ; +#79032 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79033 = EDGE_CURVE ( 'NONE', #3163, #99681, #52723, .T. ) ; +#79034 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#79035 = EDGE_CURVE ( 'NONE', #61653, #35265, #48483, .T. ) ; +#79036 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75936, 'distance_accuracy_value', 'NONE'); +#79037 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#79038 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#79039 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85499 ), #49686 ) ; +#79040 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46787, 'distance_accuracy_value', 'NONE'); +#79041 = VERTEX_POINT ( 'NONE', #53720 ) ; +#79042 = ORIENTED_EDGE ( 'NONE', *, *, #83271, .F. ) ; +#79044 = STYLED_ITEM ( 'NONE', ( #71428 ), #27154 ) ; +#79043 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54571 ), #85507 ) ; +#79045 = EDGE_CURVE ( 'NONE', #88578, #11081, #100064, .T. ) ; +#79046 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29148 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32027, #79512, #77987 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79047 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79048 = VERTEX_POINT ( 'NONE', #37903 ) ; +#79049 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79050 = LINE ( 'NONE', #94333, #54733 ) ; +#79051 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79052 = CARTESIAN_POINT ( 'NONE', ( -1.353802252918679949, -0.9813977598329840513, 0.8299999999999997380 ) ) ; +#79053 = EDGE_CURVE ( 'NONE', #71141, #28296, #46538, .T. ) ; +#79054 = VECTOR ( 'NONE', #59759, 1000.000000000000000 ) ; +#79055 = SURFACE_STYLE_FILL_AREA ( #47900 ) ; +#79057 = ORIENTED_EDGE ( 'NONE', *, *, #43608, .T. ) ; +#79056 = ORIENTED_EDGE ( 'NONE', *, *, #51334, .T. ) ; +#79058 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79059 = EDGE_LOOP ( 'NONE', ( #10506, #71748, #59145, #9323 ) ) ; +#79060 = ORIENTED_EDGE ( 'NONE', *, *, #75832, .T. ) ; +#79061 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#79062 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70893 ), #72482 ) ; +#79063 = FILL_AREA_STYLE_COLOUR ( '', #76653 ) ; +#79065 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79064 = CARTESIAN_POINT ( 'NONE', ( 0.5034558050616539937, -0.9558425862917759863, 0.8299999999999999600 ) ) ; +#79066 = VERTEX_POINT ( 'NONE', #54229 ) ; +#79067 = SURFACE_STYLE_FILL_AREA ( #55605 ) ; +#79068 = FACE_OUTER_BOUND ( 'NONE', #1933, .T. ) ; +#79069 = LINE ( 'NONE', #39233, #24288 ) ; +#79070 = VECTOR ( 'NONE', #97226, 1000.000000000000000 ) ; +#79071 = VERTEX_POINT ( 'NONE', #13846 ) ; +#79073 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4299999999943793227, 0.000000000000000000 ) ) ; +#79072 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79074 = ORIENTED_EDGE ( 'NONE', *, *, #53728, .T. ) ; +#79076 = FACE_OUTER_BOUND ( 'NONE', #6225, .T. ) ; +#79075 = LINE ( 'NONE', #33107, #63416 ) ; +#79077 = ORIENTED_EDGE ( 'NONE', *, *, #39476, .T. ) ; +#79078 = ORIENTED_EDGE ( 'NONE', *, *, #66510, .F. ) ; +#79079 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79080 = VECTOR ( 'NONE', #16662, 1000.000000000000000 ) ; +#79081 = SURFACE_STYLE_FILL_AREA ( #64756 ) ; +#79082 = FILL_AREA_STYLE_COLOUR ( '', #94485 ) ; +#79084 = VERTEX_POINT ( 'NONE', #85350 ) ; +#79083 = LINE ( 'NONE', #9039, #26671 ) ; +#79085 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79086 = PRESENTATION_STYLE_ASSIGNMENT (( #55621 ) ) ; +#79087 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4078 ) ) ; +#79088 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79089 = STYLED_ITEM ( 'NONE', ( #75098 ), #53906 ) ; +#79090 = ORIENTED_EDGE ( 'NONE', *, *, #36527, .T. ) ; +#79092 = FACE_OUTER_BOUND ( 'NONE', #93125, .T. ) ; +#79091 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79093 = CARTESIAN_POINT ( 'NONE', ( -0.001323334233439310212, -1.190451802854979979, 0.8299999999999999600 ) ) ; +#79094 = ORIENTED_EDGE ( 'NONE', *, *, #6867, .T. ) ; +#79095 = EDGE_CURVE ( 'NONE', #29934, #89795, #99081, .T. ) ; +#79096 = EDGE_LOOP ( 'NONE', ( #33876, #39144, #3174, #57925 ) ) ; +#79098 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#79097 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79099 = SURFACE_STYLE_USAGE ( .BOTH. , #24496 ) ; +#79100 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#79101 = STYLED_ITEM ( 'NONE', ( #58944 ), #88946 ) ; +#79102 = CARTESIAN_POINT ( 'NONE', ( -0.4387205553799810032, -1.232805253472390117, 0.8100000000000000533 ) ) ; +#79103 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93680 ), #28509 ) ; +#79104 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79105 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79106 = SURFACE_STYLE_USAGE ( .BOTH. , #2502 ) ; +#79107 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.700000000000000178, 0.8299999999999999600 ) ) ; +#79108 = VERTEX_POINT ( 'NONE', #84843 ) ; +#79109 = CARTESIAN_POINT ( 'NONE', ( 0.3213506759258810130, -1.250167574961789985, 0.8100000000000000533 ) ) ; +#79110 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79111 = CARTESIAN_POINT ( 'NONE', ( 0.05204425658606930821, -1.220010286732279958, 0.8100000000000000533 ) ) ; +#79112 = EDGE_LOOP ( 'NONE', ( #32476, #38897, #30402, #43630 ) ) ; +#79113 = PRESENTATION_STYLE_ASSIGNMENT (( #55143 ) ) ; +#79114 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79115 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77405 ), #807 ) ; +#79117 = PRESENTATION_STYLE_ASSIGNMENT (( #47957 ) ) ; +#79119 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.013711183678429162 ) ) ; +#79118 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2850000000000000311, -0.1458578643762690197 ) ) ; +#79121 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51357 ), #48066 ) ; +#79120 = SURFACE_SIDE_STYLE ('',( #72957 ) ) ; +#79122 = CARTESIAN_POINT ( 'NONE', ( 9.641736999999999114, 4.135756999999999017, 0.8991599999999999593 ) ) ; +#79123 = EDGE_CURVE ( 'NONE', #95352, #16296, #44523, .T. ) ; +#79125 = AXIS2_PLACEMENT_3D ( 'NONE', #76438, #4481, #90259 ) ; +#79124 = AXIS2_PLACEMENT_3D ( 'NONE', #65492, #72661, #2731 ) ; +#79126 = SURFACE_SIDE_STYLE ('',( #17305 ) ) ; +#79127 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 4.524664999999999715, 0.8991599999999999593 ) ) ; +#79128 = CARTESIAN_POINT ( 'NONE', ( 9.492960999999999316, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#79129 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79130 = CARTESIAN_POINT ( 'NONE', ( -1.282481293671730027, -1.007957212727089935, 0.8299999999999998490 ) ) ; +#79131 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79132 = VECTOR ( 'NONE', #28370, 1000.000000000000000 ) ; +#79133 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#79134 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8648700000000000276 ) ) ; +#79135 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48782, 'distance_accuracy_value', 'NONE'); +#79136 = ORIENTED_EDGE ( 'NONE', *, *, #62764, .T. ) ; +#79137 = LINE ( 'NONE', #45920, #81914 ) ; +#79138 = EDGE_LOOP ( 'NONE', ( #48065, #45700, #1454, #66004 ) ) ; +#79139 = FILL_AREA_STYLE ('',( #40849 ) ) ; +#79140 = FILL_AREA_STYLE ('',( #24546 ) ) ; +#79141 = SURFACE_STYLE_USAGE ( .BOTH. , #16803 ) ; +#79142 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31822 ), #67734 ) ; +#79143 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79144 = FILL_AREA_STYLE_COLOUR ( '', #80731 ) ; +#79145 = ORIENTED_EDGE ( 'NONE', *, *, #12282, .T. ) ; +#79146 = VERTEX_POINT ( 'NONE', #46010 ) ; +#79147 = FILL_AREA_STYLE_COLOUR ( '', #12326 ) ; +#79148 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79149 = SURFACE_STYLE_FILL_AREA ( #1037 ) ; +#79150 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#79151 = ADVANCED_FACE ( 'NONE', ( #53229 ), #38906, .T. ) ; +#79152 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#79153 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.35000000000000142, 0.000000000000000000 ) ) ; +#79154 = VECTOR ( 'NONE', #70296, 1000.000000000000000 ) ; +#79155 = ORIENTED_EDGE ( 'NONE', *, *, #28883, .T. ) ; +#79156 = CARTESIAN_POINT ( 'NONE', ( 1.148869891942319921, -0.9585643914498560569, 0.8300000000000002931 ) ) ; +#79157 = AXIS2_PLACEMENT_3D ( 'NONE', #29804, #76270, #93063 ) ; +#79158 = LINE ( 'NONE', #71499, #47745 ) ; +#79159 = ORIENTED_EDGE ( 'NONE', *, *, #26369, .T. ) ; +#79160 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, 3.099999999999989875, 0.000000000000000000 ) ) ; +#79161 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75023 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94846, #87728, #11033 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79162 = VECTOR ( 'NONE', #100576, 1000.000000000000000 ) ; +#79163 = ORIENTED_EDGE ( 'NONE', *, *, #18873, .T. ) ; +#79164 = SURFACE_STYLE_FILL_AREA ( #71503 ) ; +#79165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43224 ) ) ; +#79166 = SURFACE_STYLE_USAGE ( .BOTH. , #70995 ) ; +#79167 = CARTESIAN_POINT ( 'NONE', ( 1.211323051948050011, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#79168 = PLANE ( 'NONE', #98749 ) ; +#79169 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79170 = ADVANCED_FACE ( 'NONE', ( #85 ), #40944, .T. ) ; +#79171 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5833333333333333703, 0.000000000000000000 ) ) ; +#79172 = DIRECTION ( 'NONE', ( -1.836909530733570078E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#79173 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7499999999822648533, 0.000000000000000000 ) ) ; +#79174 = CARTESIAN_POINT ( 'NONE', ( -0.2869335283125122871, 1.414162541288808361, 0.8099999999999998312 ) ) ; +#79176 = VERTEX_POINT ( 'NONE', #95007 ) ; +#79175 = ORIENTED_EDGE ( 'NONE', *, *, #15073, .T. ) ; +#79177 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, 0.000000000000000000 ) ) ; +#79178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79179 = EDGE_LOOP ( 'NONE', ( #12015, #9899, #56323, #59160 ) ) ; +#79180 = DIRECTION ( 'NONE', ( 0.7451594222547881508, 0.6668863736986311297, 0.000000000000000000 ) ) ; +#79181 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79182 = CARTESIAN_POINT ( 'NONE', ( 10.94988424974991581, 4.524665249749911133, 0.8648700000000000276 ) ) ; +#79183 = ORIENTED_EDGE ( 'NONE', *, *, #70666, .F. ) ; +#79184 = ORIENTED_EDGE ( 'NONE', *, *, #65652, .F. ) ; +#79186 = VECTOR ( 'NONE', #4587, 1000.000000000000000 ) ; +#79185 = PLANE ( 'NONE', #62867 ) ; +#79187 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79188 = VECTOR ( 'NONE', #75243, 1000.000000000000000 ) ; +#79189 = CARTESIAN_POINT ( 'NONE', ( -0.2259284465094109906, -1.087576819458450084, 0.8300000000000000711 ) ) ; +#79191 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79190 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#79192 = LINE ( 'NONE', #9155, #208 ) ; +#79193 = ORIENTED_EDGE ( 'NONE', *, *, #17095, .T. ) ; +#79194 = EDGE_LOOP ( 'NONE', ( #27103, #62429, #554, #71827 ) ) ; +#79195 = VECTOR ( 'NONE', #66406, 1000.000000000000000 ) ; +#79196 = ORIENTED_EDGE ( 'NONE', *, *, #88652, .F. ) ; +#79197 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79198 = EDGE_CURVE ( 'NONE', #95882, #35754, #2130, .T. ) ; +#79200 = ORIENTED_EDGE ( 'NONE', *, *, #32375, .T. ) ; +#79199 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 3.500000000000000444, 0.000000000000000000 ) ) ; +#79201 = STYLED_ITEM ( 'NONE', ( #93800 ), #12781 ) ; +#79202 = PLANE ( 'NONE', #56406 ) ; +#79203 = ORIENTED_EDGE ( 'NONE', *, *, #27729, .F. ) ; +#79204 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#79205 = CARTESIAN_POINT ( 'NONE', ( -1.036258052343875802, -1.421953058340963416, 0.8099999999996773115 ) ) ; +#79206 = VERTEX_POINT ( 'NONE', #17909 ) ; +#79207 = EDGE_CURVE ( 'NONE', #86856, #81132, #79220, .T. ) ; +#79208 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79209 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#79210 = PLANE ( 'NONE', #51869 ) ; +#79211 = LINE ( 'NONE', #79735, #77069 ) ; +#79212 = PRESENTATION_STYLE_ASSIGNMENT (( #72549 ) ) ; +#79214 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.500000000000000000, 0.1829999999999460114 ) ) ; +#79213 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79215 = DIRECTION ( 'NONE', ( 0.7071090539100487460, 0.7071045084557415761, 0.000000000000000000 ) ) ; +#79216 = VECTOR ( 'NONE', #96507, 1000.000000000000000 ) ; +#79217 = SURFACE_STYLE_FILL_AREA ( #72554 ) ; +#79218 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#79219 = ORIENTED_EDGE ( 'NONE', *, *, #22288, .F. ) ; +#79220 = LINE ( 'NONE', #93977, #19083 ) ; +#79221 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#79222 = STYLED_ITEM ( 'NONE', ( #47177 ), #83742 ) ; +#79223 = CARTESIAN_POINT ( 'NONE', ( 6.123233995736763263E-18, 0.8199999999999999512, -0.04999999999999997502 ) ) ; +#79224 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.266666666666667052, 3.495651678170177615E-76 ) ) ; +#79225 = SURFACE_STYLE_FILL_AREA ( #96529 ) ; +#79226 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.266666666666653285, 0.000000000000000000 ) ) ; +#79228 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79227 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79229 = EDGE_CURVE ( 'NONE', #68868, #14566, #56781, .T. ) ; +#79230 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79231 = AXIS2_PLACEMENT_3D ( 'NONE', #69268, #4998, #21851 ) ; +#79232 = VECTOR ( 'NONE', #93890, 1000.000000000000000 ) ; +#79233 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #10786, #49195, #80850, #73183 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79234 = AXIS2_PLACEMENT_3D ( 'NONE', #96372, #17768, #47935 ) ; +#79235 = ORIENTED_EDGE ( 'NONE', *, *, #60585, .T. ) ; +#79236 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27073 ) ) ; +#79237 = ADVANCED_FACE ( 'NONE', ( #56270 ), #87374, .T. ) ; +#79238 = PLANE ( 'NONE', #88998 ) ; +#79239 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79240 = VERTEX_POINT ( 'NONE', #70539 ) ; +#79242 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#79241 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79243 = FILL_AREA_STYLE_COLOUR ( '', #42435 ) ; +#79246 = MANIFOLD_SOLID_BREP ( 'ÊäÈë143', #20858 ) ; +#79245 = STYLED_ITEM ( 'NONE', ( #2514 ), #61888 ) ; +#79247 = PLANE ( 'NONE', #33780 ) ; +#79248 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79249 = STYLED_ITEM ( 'NONE', ( #86947 ), #22666 ) ; +#79250 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82154, 'distance_accuracy_value', 'NONE'); +#79251 = EDGE_LOOP ( 'NONE', ( #22759, #87248, #32689, #1741 ) ) ; +#79252 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79253 = ADVANCED_FACE ( 'NONE', ( #57274 ), #65392, .T. ) ; +#79254 = LINE ( 'NONE', #31769, #57744 ) ; +#79255 = EDGE_CURVE ( 'NONE', #7186, #29477, #4127, .T. ) ; +#79257 = AXIS2_PLACEMENT_3D ( 'NONE', #86736, #70386, #446 ) ; +#79256 = SURFACE_STYLE_USAGE ( .BOTH. , #70565 ) ; +#79258 = SURFACE_STYLE_FILL_AREA ( #24147 ) ; +#79259 = LINE ( 'NONE', #2665, #67037 ) ; +#79260 = CARTESIAN_POINT ( 'NONE', ( 0.06967798674591889341, -1.043958301690999901, 0.8100000000000000533 ) ) ; +#79261 = VECTOR ( 'NONE', #94311, 1000.000000000000000 ) ; +#79262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79263 = FILL_AREA_STYLE ('',( #1668 ) ) ; +#79264 = FACE_OUTER_BOUND ( 'NONE', #4563, .T. ) ; +#79265 = ORIENTED_EDGE ( 'NONE', *, *, #46477, .F. ) ; +#79266 = LINE ( 'NONE', #78745, #22092 ) ; +#79267 = ORIENTED_EDGE ( 'NONE', *, *, #91200, .F. ) ; +#79268 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97160 ), #40137 ) ; +#79269 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61492, 'distance_accuracy_value', 'NONE'); +#79270 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79271 = FILL_AREA_STYLE_COLOUR ( '', #88706 ) ; +#79272 = LINE ( 'NONE', #48133, #88449 ) ; +#79274 = ADVANCED_FACE ( 'NONE', ( #41941 ), #55001, .T. ) ; +#79273 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42484 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49933, #82078, #44237 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79275 = SURFACE_STYLE_USAGE ( .BOTH. , #70593 ) ; +#79276 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#79277 = LINE ( 'NONE', #41488, #7962 ) ; +#79278 = ORIENTED_EDGE ( 'NONE', *, *, #20359, .T. ) ; +#79279 = CARTESIAN_POINT ( 'NONE', ( 1.885232907775660216, -1.407232784796780045, 0.8300000000000011813 ) ) ; +#79280 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79281 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79282 = ORIENTED_EDGE ( 'NONE', *, *, #65050, .T. ) ; +#79283 = CARTESIAN_POINT ( 'NONE', ( 1.158276583597519949, -1.215709010884332253, 0.8099999999998543920 ) ) ; +#79284 = PRESENTATION_STYLE_ASSIGNMENT (( #40497 ) ) ; +#79285 = ORIENTED_EDGE ( 'NONE', *, *, #43597, .T. ) ; +#79286 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.649990468822289917E-78, 2.058195874565369951E-47 ) ) ; +#79287 = EDGE_CURVE ( 'NONE', #67087, #100196, #38683, .T. ) ; +#79288 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, 0.1499999999999999944 ) ) ; +#79289 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69413 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99807, #35672, #61156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79291 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79292 = LINE ( 'NONE', #30790, #44686 ) ; +#79293 = ORIENTED_EDGE ( 'NONE', *, *, #89220, .T. ) ; +#79294 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79295 = VERTEX_POINT ( 'NONE', #47309 ) ; +#79296 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.650000000000000355, 0.03429000000000000103 ) ) ; +#79297 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76881 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3258, #18036, #50759 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79298 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79299 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35059, #66169, #19709, #89664 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79300 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79301 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32000 ) ) ; +#79302 = ORIENTED_EDGE ( 'NONE', *, *, #20795, .T. ) ; +#79303 = FILL_AREA_STYLE_COLOUR ( '', #20449 ) ; +#79304 = FILL_AREA_STYLE ('',( #63985 ) ) ; +#79305 = FACE_OUTER_BOUND ( 'NONE', #62226, .T. ) ; +#79306 = FACE_OUTER_BOUND ( 'NONE', #36258, .T. ) ; +#79307 = STYLED_ITEM ( 'NONE', ( #8915 ), #78737 ) ; +#79308 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79309 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67829 ), #85772 ) ; +#79310 = ORIENTED_EDGE ( 'NONE', *, *, #54241, .F. ) ; +#79312 = ORIENTED_EDGE ( 'NONE', *, *, #3041, .F. ) ; +#79311 = ORIENTED_EDGE ( 'NONE', *, *, #58685, .F. ) ; +#79313 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79314 = PRODUCT ( 'C0402_20210301.xtd', 'C0402_20210301.xtd', '', ( #9523 ) ) ; +#79315 = ORIENTED_EDGE ( 'NONE', *, *, #6456, .F. ) ; +#79316 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79317 = ADVANCED_FACE ( 'NONE', ( #24879 ), #7915, .T. ) ; +#79318 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23867 ), #66269 ) ; +#79319 = VECTOR ( 'NONE', #48383, 1000.000000000000000 ) ; +#79320 = VERTEX_POINT ( 'NONE', #46788 ) ; +#79322 = VERTEX_POINT ( 'NONE', #55512 ) ; +#79321 = SURFACE_SIDE_STYLE ('',( #56377 ) ) ; +#79323 = SURFACE_STYLE_USAGE ( .BOTH. , #17005 ) ; +#79324 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#79325 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.699999999999999956, -0.02000000000003073625 ) ) ; +#79326 = ORIENTED_EDGE ( 'NONE', *, *, #74776, .T. ) ; +#79327 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8100000000000000533 ) ) ; +#79328 = VERTEX_POINT ( 'NONE', #71816 ) ; +#79329 = EDGE_CURVE ( 'NONE', #26091, #19154, #25375, .T. ) ; +#79330 = FILL_AREA_STYLE ('',( #72171 ) ) ; +#79331 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67848 ), #17348 ) ; +#79332 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #57255, #88368, #93960, #80729, #24091, #16365, #40414, #1608, #47544, #94990, #25111, #78680, #56248, #87355, #59282, #96993, #90880, #19926, #27112 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.089423564698657371E-05, 4.127107460520045414E-05, 6.136790752972443551E-05, 8.103384712156605865E-05, 0.0001004202814139419989, 0.0001190560773535569161, 0.0001373225389746647281, 0.0001552515924647247087, 0.0001731506795507366258, 0.0001909683545410049716, 0.0002089256637183211848, 0.0002273453629910950535, 0.0002462354757949162458, 0.0002657277680313440337, 0.0002860044708918602486, 0.0003073966275650936238 ), + .UNSPECIFIED. ) ; +#79333 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#79334 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79335 = FILL_AREA_STYLE ('',( #79848 ) ) ; +#79336 = ORIENTED_EDGE ( 'NONE', *, *, #83578, .T. ) ; +#79337 = EDGE_CURVE ( 'NONE', #9775, #24683, #1357, .T. ) ; +#79338 = SURFACE_SIDE_STYLE ('',( #32873 ) ) ; +#79339 = ORIENTED_EDGE ( 'NONE', *, *, #28088, .F. ) ; +#79340 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54939 ) ) ; +#79341 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 2.983172999999999853, 0.8648700000000000276 ) ) ; +#79342 = AXIS2_PLACEMENT_3D ( 'NONE', #89117, #11415, #19141 ) ; +#79343 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.123820061220085265, -0.02000000000000000042 ) ) ; +#79344 = LINE ( 'NONE', #50245, #45623 ) ; +#79345 = STYLED_ITEM ( 'NONE', ( #46248 ), #4082 ) ; +#79346 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79347 = VECTOR ( 'NONE', #9884, 1000.000000000000000 ) ; +#79348 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.000000000000000000 ) ) ; +#79349 = ORIENTED_EDGE ( 'NONE', *, *, #75029, .F. ) ; +#79350 = PRESENTATION_STYLE_ASSIGNMENT (( #17034 ) ) ; +#79351 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#79352 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79353 = SURFACE_STYLE_FILL_AREA ( #41072 ) ; +#79354 = ADVANCED_FACE ( 'NONE', ( #23850 ), #97056, .F. ) ; +#79355 = SURFACE_SIDE_STYLE ('',( #8806 ) ) ; +#79356 = LINE ( 'NONE', #24764, #68990 ) ; +#79357 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.19999999999999929, 0.000000000000000000 ) ) ; +#79358 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#79359 = ORIENTED_EDGE ( 'NONE', *, *, #9503, .T. ) ; +#79360 = CARTESIAN_POINT ( 'NONE', ( 6.389045124874956905, 9.651189124874957059, 0.8991599999999999593 ) ) ; +#79362 = AXIS2_PLACEMENT_3D ( 'NONE', #58303, #50133, #81275 ) ; +#79361 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#79365 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#79364 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#79363 = FILL_AREA_STYLE_COLOUR ( '', #70775 ) ; +#79366 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79367 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5079, 'distance_accuracy_value', 'NONE'); +#79368 = CARTESIAN_POINT ( 'NONE', ( 0.2985587656685099733, -1.344342053265010106, 0.8100000000000000533 ) ) ; +#79369 = PRESENTATION_STYLE_ASSIGNMENT (( #56424 ) ) ; +#79370 = SURFACE_SIDE_STYLE ('',( #71708 ) ) ; +#79371 = FACE_OUTER_BOUND ( 'NONE', #38745, .T. ) ; +#79372 = VERTEX_POINT ( 'NONE', #22195 ) ; +#79373 = ADVANCED_FACE ( 'NONE', ( #20173 ), #61024, .T. ) ; +#79374 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45725 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16168, #31522, #47855 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79375 = CARTESIAN_POINT ( 'NONE', ( 6.049999999999999822, 9.949999999999999289, -1.355252715606880543E-17 ) ) ; +#79376 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.000000000000000000 ) ) ; +#79377 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#79378 = ADVANCED_FACE ( 'NONE', ( #12954 ), #52359, .T. ) ; +#79379 = SURFACE_SIDE_STYLE ('',( #72214 ) ) ; +#79380 = FILL_AREA_STYLE_COLOUR ( '', #596 ) ; +#79381 = LINE ( 'NONE', #79897, #33910 ) ; +#79382 = LINE ( 'NONE', #64067, #94128 ) ; +#79383 = DIRECTION ( 'NONE', ( -0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#79384 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85850 ), #72824 ) ; +#79385 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 9.983529000000000764, 0.8648700000000000276 ) ) ; +#79386 = EDGE_CURVE ( 'NONE', #51520, #33000, #69107, .T. ) ; +#79387 = SURFACE_STYLE_USAGE ( .BOTH. , #65066 ) ; +#79388 = SURFACE_STYLE_FILL_AREA ( #78375 ) ; +#79389 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79390 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79391 = FILL_AREA_STYLE_COLOUR ( '', #99475 ) ; +#79392 = FACE_OUTER_BOUND ( 'NONE', #26989, .T. ) ; +#79393 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79394 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79395 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#79396 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51650 ), #89233 ) ; +#79397 = ORIENTED_EDGE ( 'NONE', *, *, #40491, .T. ) ; +#79398 = VERTEX_POINT ( 'NONE', #76307 ) ; +#79399 = SURFACE_SIDE_STYLE ('',( #39577 ) ) ; +#79401 = VECTOR ( 'NONE', #84142, 1000.000000000000000 ) ; +#79400 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1458578643762690474 ) ) ; +#79403 = VECTOR ( 'NONE', #96208, 1000.000000000000000 ) ; +#79402 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79404 = ADVANCED_FACE ( 'NONE', ( #6305 ), #45631, .T. ) ; +#79405 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79406 = LINE ( 'NONE', #25302, #73686 ) ; +#79407 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79408 = CARTESIAN_POINT ( 'NONE', ( -1.233538577444069917, -1.130592060098940088, 0.8299999999999999600 ) ) ; +#79409 = EDGE_LOOP ( 'NONE', ( #5434, #99282, #95203, #80840 ) ) ; +#79410 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#79411 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#79412 = ADVANCED_FACE ( 'NONE', ( #31358 ), #1759, .T. ) ; +#79413 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22316 ), #95688 ) ; +#79414 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 9.262281000000001541, 0.8648700000000000276 ) ) ; +#79415 = SURFACE_SIDE_STYLE ('',( #25309 ) ) ; +#79416 = EDGE_LOOP ( 'NONE', ( #54187, #29222, #50165, #78234 ) ) ; +#79417 = VECTOR ( 'NONE', #98526, 1000.000000000000114 ) ; +#79418 = SURFACE_STYLE_FILL_AREA ( #97449 ) ; +#79419 = COLOUR_RGB ( '',0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ; +#79420 = SURFACE_SIDE_STYLE ('',( #56968 ) ) ; +#79421 = EDGE_CURVE ( 'NONE', #82708, #69719, #15290, .T. ) ; +#79423 = EDGE_CURVE ( 'NONE', #45932, #43157, #32387, .T. ) ; +#79422 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#79424 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.100000000000000089, 1.048695503451053346E-76 ) ) ; +#79425 = MANIFOLD_SOLID_BREP ( 'ÊäÈë87', #82887 ) ; +#79426 = EDGE_LOOP ( 'NONE', ( #72889, #58117, #9422, #39458 ) ) ; +#79427 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79428 = FILL_AREA_STYLE ('',( #96215 ) ) ; +#79429 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79430 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88236, 'distance_accuracy_value', 'NONE'); +#79431 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#79432 = ORIENTED_EDGE ( 'NONE', *, *, #990, .T. ) ; +#79433 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79434 = FILL_AREA_STYLE_COLOUR ( '', #27715 ) ; +#79435 = LINE ( 'NONE', #55968, #85172 ) ; +#79436 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49506 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91809, #54037, #46341 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79437 = EDGE_LOOP ( 'NONE', ( #72142, #65014, #41886, #15905 ) ) ; +#79438 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#79439 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50432 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80635, #31625, #87255 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79440 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79441 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79442 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79443 = EDGE_CURVE ( 'NONE', #64741, #50096, #24756, .T. ) ; +#79444 = ORIENTED_EDGE ( 'NONE', *, *, #97955, .F. ) ; +#79446 = ORIENTED_EDGE ( 'NONE', *, *, #60621, .F. ) ; +#79445 = SURFACE_STYLE_FILL_AREA ( #88111 ) ; +#79447 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79448 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58271 ), #64783 ) ; +#79449 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37986, 'distance_accuracy_value', 'NONE'); +#79450 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, -3.099999999999994316, 0.000000000000000000 ) ) ; +#79451 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79452 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79453 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 4.849935000000000329, 0.8991599999999999593 ) ) ; +#79454 = EDGE_LOOP ( 'NONE', ( #26460, #37615, #70771, #29166 ) ) ; +#79455 = ADVANCED_FACE ( 'NONE', ( #7786 ), #23720, .T. ) ; +#79456 = STYLED_ITEM ( 'NONE', ( #55422 ), #55095 ) ; +#79457 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79458 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#79459 = PRESENTATION_STYLE_ASSIGNMENT (( #18640 ) ) ; +#79460 = SURFACE_STYLE_USAGE ( .BOTH. , #48331 ) ; +#79461 = VERTEX_POINT ( 'NONE', #25258 ) ; +#79462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89221 ), #30493 ) ; +#79463 = EDGE_CURVE ( 'NONE', #76735, #72485, #24149, .T. ) ; +#79465 = SURFACE_STYLE_FILL_AREA ( #31472 ) ; +#79464 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#79466 = ORIENTED_EDGE ( 'NONE', *, *, #86150, .F. ) ; +#79467 = ORIENTED_EDGE ( 'NONE', *, *, #97765, .T. ) ; +#79468 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.35000000000000142 ) ) ; +#79470 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79469 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8100000000000001643 ) ) ; +#79471 = SURFACE_STYLE_FILL_AREA ( #86603 ) ; +#79472 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53355 ) ) ; +#79473 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86001 ), #55061 ) ; +#79474 = VERTEX_POINT ( 'NONE', #27256 ) ; +#79475 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32166 ), #67979 ) ; +#79476 = CIRCLE ( 'NONE', #33860, 0.1100000000000007222 ) ; +#79477 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30899, #93151, #47741, #62586, #85527, #78385, #15549, #63596 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000000555, 0.5000000000000001110, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79478 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79479 = ORIENTED_EDGE ( 'NONE', *, *, #70043, .T. ) ; +#79480 = FILL_AREA_STYLE ('',( #50376 ) ) ; +#79481 = FILL_AREA_STYLE ('',( #33001 ) ) ; +#79482 = ORIENTED_EDGE ( 'NONE', *, *, #374, .T. ) ; +#79483 = ORIENTED_EDGE ( 'NONE', *, *, #72913, .T. ) ; +#79484 = SURFACE_SIDE_STYLE ('',( #57520 ) ) ; +#79485 = CLOSED_SHELL ( 'NONE', ( #40027, #38040, #11047, #10983, #49672, #61517 ) ) ; +#79486 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79487 = SURFACE_STYLE_FILL_AREA ( #23341 ) ; +#79488 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7213 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87650, #1380, #18165 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79489 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#79490 = VECTOR ( 'NONE', #15303, 1000.000000000000000 ) ; +#79491 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#79492 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79493 = CARTESIAN_POINT ( 'NONE', ( -0.08150952889499120391, -1.159841243706410063, 0.8299999999999999600 ) ) ; +#79494 = EDGE_CURVE ( 'NONE', #66883, #78971, #44613, .T. ) ; +#79495 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#79496 = VECTOR ( 'NONE', #37767, 1000.000000000000000 ) ; +#79497 = ORIENTED_EDGE ( 'NONE', *, *, #14069, .F. ) ; +#79498 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139848000000000638, 0.8648700000000000276 ) ) ; +#79499 = FILL_AREA_STYLE_COLOUR ( '', #61172 ) ; +#79500 = CARTESIAN_POINT ( 'NONE', ( -0.1525548447364439841, -1.164073081312986924, 0.8100000000000002753 ) ) ; +#79501 = LINE ( 'NONE', #47840, #19131 ) ; +#79502 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.405583712835721810, -11.41999999999999993 ) ) ; +#79503 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56560, #10974, #80527, #86660 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79504 = ORIENTED_EDGE ( 'NONE', *, *, #31546, .T. ) ; +#79505 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79507 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75188, 'distance_accuracy_value', 'NONE'); +#79506 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79508 = PRESENTATION_STYLE_ASSIGNMENT (( #80512 ) ) ; +#79509 = EDGE_CURVE ( 'NONE', #7897, #45346, #58419, .T. ) ; +#79510 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8648700000000000276 ) ) ; +#79511 = AXIS2_PLACEMENT_3D ( 'NONE', #29431, #6381, #67705 ) ; +#79512 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79513 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9296 ), #92502 ) ; +#79514 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.450000000000000178, 0.03429000000000000103 ) ) ; +#79515 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#79516 = SURFACE_STYLE_USAGE ( .BOTH. , #100827 ) ; +#79517 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450000000000000178, 0.000000000000000000 ) ) ; +#79518 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92439 ), #40377 ) ; +#79519 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#79520 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#79521 = CARTESIAN_POINT ( 'NONE', ( 10.92867050050017319, 5.422690500500176647, 0.8991599999999999593 ) ) ; +#79522 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79523 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79524 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84379 ), #30556 ) ; +#79525 = VERTEX_POINT ( 'NONE', #18552 ) ; +#79526 = LINE ( 'NONE', #42605, #15183 ) ; +#79528 = VECTOR ( 'NONE', #42592, 1000.000000000000114 ) ; +#79527 = LINE ( 'NONE', #94804, #95887 ) ; +#79529 = FACE_OUTER_BOUND ( 'NONE', #22974, .T. ) ; +#79531 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79530 = CARTESIAN_POINT ( 'NONE', ( 0.006444788832097659778, -1.283680827045200035, 0.8300000000000002931 ) ) ; +#79532 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#79533 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79534 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89300 ) ) ; +#79535 = PRESENTATION_STYLE_ASSIGNMENT (( #70861 ) ) ; +#79536 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#79538 = VERTEX_POINT ( 'NONE', #95635 ) ; +#79537 = VECTOR ( 'NONE', #57824, 1000.000000000000000 ) ; +#79539 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79540 = FACE_OUTER_BOUND ( 'NONE', #14733, .T. ) ; +#79541 = ADVANCED_FACE ( 'NONE', ( #56899 ), #41560, .T. ) ; +#79542 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, -0.02000000000000000042 ) ) ; +#79543 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37125 ) ) ; +#79544 = VECTOR ( 'NONE', #65863, 1000.000000000000000 ) ; +#79545 = PRESENTATION_STYLE_ASSIGNMENT (( #2440 ) ) ; +#79546 = CLOSED_SHELL ( 'NONE', ( #83640, #14782, #64428, #31215, #72136, #23774, #12535, #34045, #28656, #98176, #10389, #98443, #76696, #5566, #40306, #49425, #57702, #74707, #60713, #92042, #63311, #70829, #16277, #22268, #90584, #14334, #28227, #37582, #81757, #58638, #44026, #81379, #53316, #52516, #89363, #3507, #23300, #88536, #18145, #64040, #20261, #29956, #18795, #86639, #48119, #29988, #5926, #15136, #26320, #51646, #93391, #85176, #53178, #71828, #11396, #12986, #82086, #8154, #3392, #95125, #50018, #50372, #26528, #1589, #36502 ) ) ; +#79547 = VECTOR ( 'NONE', #45914, 999.9999999999998863 ) ; +#79548 = ORIENTED_EDGE ( 'NONE', *, *, #4447, .F. ) ; +#79549 = ORIENTED_EDGE ( 'NONE', *, *, #21560, .T. ) ; +#79550 = STYLED_ITEM ( 'NONE', ( #43475 ), #56855 ) ; +#79551 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980549, 0.000000000000000000 ) ) ; +#79552 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#79553 = VERTEX_POINT ( 'NONE', #65034 ) ; +#79554 = FACE_OUTER_BOUND ( 'NONE', #94192, .T. ) ; +#79555 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79556 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#79557 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -0.9701298701298699534, 0.8099999999999119016 ) ) ; +#79558 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79559 = AXIS2_PLACEMENT_3D ( 'NONE', #33646, #95368, #25482 ) ; +#79560 = SHAPE_DEFINITION_REPRESENTATION ( #31161, #44181 ) ; +#79561 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#79562 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79563 = VECTOR ( 'NONE', #47473, 1000.000000000000000 ) ; +#79566 = ORIENTED_EDGE ( 'NONE', *, *, #99985, .F. ) ; +#79565 = VERTEX_POINT ( 'NONE', #81391 ) ; +#79564 = EDGE_CURVE ( 'NONE', #47331, #51408, #12688, .T. ) ; +#79567 = EDGE_LOOP ( 'NONE', ( #1938, #20812, #14450, #60765 ) ) ; +#79568 = AXIS2_PLACEMENT_3D ( 'NONE', #8973, #12369, #81923 ) ; +#79569 = EDGE_LOOP ( 'NONE', ( #5076, #62757, #33720, #88460 ) ) ; +#79570 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64532, 'distance_accuracy_value', 'NONE'); +#79571 = PRESENTATION_STYLE_ASSIGNMENT (( #9531 ) ) ; +#79573 = FILL_AREA_STYLE_COLOUR ( '', #70890 ) ; +#79572 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8100000000000000533 ) ) ; +#79574 = ORIENTED_EDGE ( 'NONE', *, *, #29540, .F. ) ; +#79575 = EDGE_CURVE ( 'NONE', #82440, #90126, #42561, .T. ) ; +#79576 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79577 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.551691174664149102E-48, 3.358555288063679845E-32 ) ) ; +#79578 = ORIENTED_EDGE ( 'NONE', *, *, #44433, .T. ) ; +#79580 = EDGE_LOOP ( 'NONE', ( #48940, #63288, #8404, #61448 ) ) ; +#79579 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22485 ) ) ; +#79581 = VERTEX_POINT ( 'NONE', #98583 ) ; +#79582 = EDGE_LOOP ( 'NONE', ( #27385, #37171, #26469, #1283 ) ) ; +#79583 = CARTESIAN_POINT ( 'NONE', ( 0.2985587656685099733, -1.344342053265010106, 0.8300000000000004041 ) ) ; +#79584 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55113 ), #63277 ) ; +#79585 = FACE_OUTER_BOUND ( 'NONE', #27093, .T. ) ; +#79586 = LINE ( 'NONE', #41296, #27699 ) ; +#79587 = MANIFOLD_SOLID_BREP ( 'ÊäÈë9', #27298 ) ; +#79589 = EDGE_CURVE ( 'NONE', #11053, #93901, #28245, .T. ) ; +#79588 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79591 = ORIENTED_EDGE ( 'NONE', *, *, #87800, .T. ) ; +#79590 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#79592 = STYLED_ITEM ( 'NONE', ( #28691 ), #56389 ) ; +#79593 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#79594 = LINE ( 'NONE', #23978, #99529 ) ; +#79595 = STYLED_ITEM ( 'NONE', ( #64089 ), #84661 ) ; +#79596 = CARTESIAN_POINT ( 'NONE', ( -0.1190035524734260053, -0.9001377335631759458, 0.8299999999999999600 ) ) ; +#79597 = FILL_AREA_STYLE_COLOUR ( '', #4910 ) ; +#79598 = ORIENTED_EDGE ( 'NONE', *, *, #84319, .T. ) ; +#79600 = CYLINDRICAL_SURFACE ( 'NONE', #46866, 0.6999999999999999556 ) ; +#79599 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#79601 = CARTESIAN_POINT ( 'NONE', ( 0.09190937866851861537, -1.304291937284929981, 0.8299999999999999600 ) ) ; +#79602 = VERTEX_POINT ( 'NONE', #21086 ) ; +#79603 = EDGE_CURVE ( 'NONE', #93361, #27423, #60905, .T. ) ; +#79604 = ORIENTED_EDGE ( 'NONE', *, *, #45699, .F. ) ; +#79605 = FILL_AREA_STYLE ('',( #24991 ) ) ; +#79606 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14081 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68799, #6477, #68313 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79607 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79608 = FILL_AREA_STYLE_COLOUR ( '', #56256 ) ; +#79609 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46911 ) ) ; +#79610 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79611 = EDGE_CURVE ( 'NONE', #100499, #53045, #76197, .T. ) ; +#79613 = EDGE_CURVE ( 'NONE', #89742, #9413, #46975, .T. ) ; +#79612 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8648700000000000276 ) ) ; +#79614 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#79616 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79615 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66788, 'distance_accuracy_value', 'NONE'); +#79617 = CARTESIAN_POINT ( 'NONE', ( 8.800278999999999741, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#79618 = ORIENTED_EDGE ( 'NONE', *, *, #35954, .T. ) ; +#79619 = PRESENTATION_STYLE_ASSIGNMENT (( #56656 ) ) ; +#79620 = VECTOR ( 'NONE', #36079, 1000.000000000000000 ) ; +#79621 = SURFACE_SIDE_STYLE ('',( #33664 ) ) ; +#79622 = ORIENTED_EDGE ( 'NONE', *, *, #96381, .F. ) ; +#79623 = STYLED_ITEM ( 'NONE', ( #52481 ), #803 ) ; +#79624 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#79625 = PLANE ( 'NONE', #5703 ) ; +#79626 = EDGE_CURVE ( 'NONE', #87484, #33000, #60417, .T. ) ; +#79627 = EDGE_CURVE ( 'NONE', #66499, #8103, #45510, .T. ) ; +#79628 = PRESENTATION_STYLE_ASSIGNMENT (( #78579 ) ) ; +#79629 = AXIS2_PLACEMENT_3D ( 'NONE', #97562, #42963, #74622 ) ; +#79630 = SURFACE_STYLE_FILL_AREA ( #40822 ) ; +#79632 = FACE_OUTER_BOUND ( 'NONE', #96998, .T. ) ; +#79631 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#79633 = LINE ( 'NONE', #41825, #91099 ) ; +#79634 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79635 = CLOSED_SHELL ( 'NONE', ( #78801, #35627, #91956, #6366, #97630, #79012 ) ) ; +#79636 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#79637 = EDGE_CURVE ( 'NONE', #33492, #25087, #51895, .T. ) ; +#79638 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#79639 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#79640 = STYLED_ITEM ( 'NONE', ( #37788 ), #50485 ) ; +#79641 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79642 = EDGE_CURVE ( 'NONE', #97585, #3356, #90009, .T. ) ; +#79643 = LINE ( 'NONE', #8562, #16230 ) ; +#79644 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74744 ) ) ; +#79645 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79646 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#79647 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#79648 = STYLED_ITEM ( 'NONE', ( #70068 ), #43888 ) ; +#79649 = ORIENTED_EDGE ( 'NONE', *, *, #79707, .T. ) ; +#79650 = CARTESIAN_POINT ( 'NONE', ( 4.532236000000000153, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#79651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65191, 'distance_accuracy_value', 'NONE'); +#79652 = ORIENTED_EDGE ( 'NONE', *, *, #92010, .F. ) ; +#79654 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51379, 'distance_accuracy_value', 'NONE'); +#79653 = SURFACE_STYLE_USAGE ( .BOTH. , #10086 ) ; +#79655 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#79656 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#79657 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -11.57000000000000028 ) ) ; +#79659 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#79658 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #29487, .NOT_KNOWN. ) ; +#79660 = AXIS2_PLACEMENT_3D ( 'NONE', #96426, #81169, #96935 ) ; +#79661 = AXIS2_PLACEMENT_3D ( 'NONE', #98936, #20410, #29089 ) ; +#79662 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1399999999999999856 ) ) ; +#79663 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.1238200612200849871, -0.02000000000000000042 ) ) ; +#79664 = ORIENTED_EDGE ( 'NONE', *, *, #96523, .F. ) ; +#79665 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#79666 = ORIENTED_EDGE ( 'NONE', *, *, #95257, .F. ) ; +#79667 = EDGE_CURVE ( 'NONE', #31980, #34647, #66532, .T. ) ; +#79668 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78508, 'distance_accuracy_value', 'NONE'); +#79669 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79670 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#79671 = PLANE ( 'NONE', #15070 ) ; +#79672 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50396 ), #9458 ) ; +#79673 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38085 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26043, #18327, #49513 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79675 = EDGE_CURVE ( 'NONE', #64435, #24225, #37423, .T. ) ; +#79676 = EDGE_LOOP ( 'NONE', ( #90928, #19053, #17872, #100886 ) ) ; +#79678 = FACE_OUTER_BOUND ( 'NONE', #62173, .T. ) ; +#79677 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81295 ), #51908 ) ; +#79679 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#79680 = ORIENTED_EDGE ( 'NONE', *, *, #33101, .F. ) ; +#79681 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#79682 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79683 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79684 = EDGE_LOOP ( 'NONE', ( #65613, #58532, #85823, #7987 ) ) ; +#79685 = SURFACE_STYLE_USAGE ( .BOTH. , #48544 ) ; +#79686 = FILL_AREA_STYLE ('',( #48546 ) ) ; +#79687 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#79688 = FILL_AREA_STYLE_COLOUR ( '', #953 ) ; +#79689 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79690 = AXIS2_PLACEMENT_3D ( 'NONE', #98455, #19932, #34784 ) ; +#79691 = SURFACE_STYLE_FILL_AREA ( #48549 ) ; +#79692 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.224606353822379970E-16, 0.000000000000000000 ) ) ; +#79693 = AXIS2_PLACEMENT_3D ( 'NONE', #14775, #38818, #69421 ) ; +#79695 = VERTEX_POINT ( 'NONE', #67511 ) ; +#79694 = EDGE_LOOP ( 'NONE', ( #6104, #68370, #39871, #61886 ) ) ; +#79696 = CIRCLE ( 'NONE', #42152, 0.1000000000000000472 ) ; +#79697 = CARTESIAN_POINT ( 'NONE', ( 1.689681756505250210, -0.9624218420162740095, 0.8099999999999994982 ) ) ; +#79698 = SURFACE_SIDE_STYLE ('',( #39863 ) ) ; +#79700 = STYLED_ITEM ( 'NONE', ( #29902 ), #42027 ) ; +#79699 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79701 = VERTEX_POINT ( 'NONE', #82374 ) ; +#79702 = PLANE ( 'NONE', #366 ) ; +#79704 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79703 = FILL_AREA_STYLE_COLOUR ( '', #35902 ) ; +#79705 = ORIENTED_EDGE ( 'NONE', *, *, #66666, .T. ) ; +#79707 = EDGE_CURVE ( 'NONE', #23706, #50947, #36904, .T. ) ; +#79706 = VERTEX_POINT ( 'NONE', #13327 ) ; +#79708 = FACE_OUTER_BOUND ( 'NONE', #35161, .T. ) ; +#79709 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79710 = FACE_OUTER_BOUND ( 'NONE', #74170, .T. ) ; +#79711 = LINE ( 'NONE', #9650, #92647 ) ; +#79712 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#79713 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79715 = ORIENTED_EDGE ( 'NONE', *, *, #73030, .T. ) ; +#79714 = VECTOR ( 'NONE', #36680, 1000.000000000000000 ) ; +#79716 = ORIENTED_EDGE ( 'NONE', *, *, #22, .F. ) ; +#79717 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.699999999999999734, 0.1829999999999460114 ) ) ; +#79718 = ORIENTED_EDGE ( 'NONE', *, *, #79564, .F. ) ; +#79719 = SURFACE_STYLE_FILL_AREA ( #48577 ) ; +#79720 = STYLED_ITEM ( 'NONE', ( #78344 ), #50218 ) ; +#79721 = ORIENTED_EDGE ( 'NONE', *, *, #4853, .F. ) ; +#79722 = SURFACE_SIDE_STYLE ('',( #53192 ) ) ; +#79723 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79724 = FACE_OUTER_BOUND ( 'NONE', #23178, .T. ) ; +#79725 = EDGE_LOOP ( 'NONE', ( #67586, #84730, #7101, #43954, #72042, #53048 ) ) ; +#79726 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#79727 = CARTESIAN_POINT ( 'NONE', ( -1.011231128532416479, -1.401660485983069027, 0.8099999999996924105 ) ) ; +#79728 = VERTEX_POINT ( 'NONE', #99587 ) ; +#79729 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7100000000000001865, -1.079289321881345076 ) ) ; +#79730 = FILL_AREA_STYLE ('',( #48590 ) ) ; +#79731 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79893 ), #92865 ) ; +#79732 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#79733 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#79734 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#79735 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#79736 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1833333333333329873, 0.000000000000000000 ) ) ; +#79737 = SURFACE_STYLE_USAGE ( .BOTH. , #49597 ) ; +#79738 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22647 ) ) ; +#79740 = FACE_OUTER_BOUND ( 'NONE', #38331, .T. ) ; +#79739 = CARTESIAN_POINT ( 'NONE', ( -0.4878933045820542103, -1.170211713208591187, 0.8300000000000001821 ) ) ; +#79741 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84580 ) ) ; +#79742 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 4.849935000000000329, 0.8991599999999999593 ) ) ; +#79743 = ORIENTED_EDGE ( 'NONE', *, *, #92020, .F. ) ; +#79744 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000007994, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#79745 = ORIENTED_EDGE ( 'NONE', *, *, #62634, .F. ) ; +#79746 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79748 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#79747 = STYLED_ITEM ( 'NONE', ( #49829 ), #56867 ) ; +#79749 = EDGE_CURVE ( 'NONE', #34839, #58620, #22072, .T. ) ; +#79750 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86269 ), #92721 ) ; +#79751 = CIRCLE ( 'NONE', #69928, 0.1000000000000000472 ) ; +#79752 = CARTESIAN_POINT ( 'NONE', ( 5.264745041625020328, 6.971255041625060045, 0.8991599999999999593 ) ) ; +#79753 = CARTESIAN_POINT ( 'NONE', ( 0.3999999999999998002, 0.6700000000000000400, -0.1999999999999999001 ) ) ; +#79755 = PLANE ( 'NONE', #76921 ) ; +#79754 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#79756 = DIRECTION ( 'NONE', ( 0.3918432626949318598, -0.9200319872051138104, 0.000000000000000000 ) ) ; +#79757 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#79758 = STYLED_ITEM ( 'NONE', ( #38224 ), #6011 ) ; +#79759 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#79760 = STYLED_ITEM ( 'NONE', ( #80640 ), #80100 ) ; +#79761 = EDGE_CURVE ( 'NONE', #25071, #63592, #35433, .T. ) ; +#79762 = ORIENTED_EDGE ( 'NONE', *, *, #72108, .T. ) ; +#79763 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79765 = MANIFOLD_SOLID_BREP ( 'ÊäÈë27', #7782 ) ; +#79764 = AXIS2_PLACEMENT_3D ( 'NONE', #3254, #51239, #66045 ) ; +#79766 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79767 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79768 = AXIS2_PLACEMENT_3D ( 'NONE', #56773, #10677, #40934 ) ; +#79769 = ORIENTED_EDGE ( 'NONE', *, *, #52202, .T. ) ; +#79770 = LINE ( 'NONE', #96547, #27750 ) ; +#79771 = CARTESIAN_POINT ( 'NONE', ( 0.1681119866146560116, 0.5791465759269650571, 0.8100000000000001643 ) ) ; +#79772 = SURFACE_STYLE_FILL_AREA ( #48632 ) ; +#79773 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#79774 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#79775 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79776 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65039 ), #91125 ) ; +#79778 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 0.1199999999999999956, 0.6500000000000001332 ) ) ; +#79779 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84324, 'distance_accuracy_value', 'NONE'); +#79780 = STYLED_ITEM ( 'NONE', ( #18068 ), #15394 ) ; +#79781 = SURFACE_STYLE_FILL_AREA ( #79263 ) ; +#79782 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#79783 = VERTEX_POINT ( 'NONE', #54237 ) ; +#79784 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8648700000000000276 ) ) ; +#79785 = VERTEX_POINT ( 'NONE', #55266 ) ; +#79786 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34318, 'distance_accuracy_value', 'NONE'); +#79787 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5930, 'distance_accuracy_value', 'NONE'); +#79788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81410 ) ) ; +#79789 = FILL_AREA_STYLE ('',( #50664 ) ) ; +#79790 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999500082 ) ) ; +#79791 = CARTESIAN_POINT ( 'NONE', ( 10.82260499999999936, 8.130910000000000082, 0.8648700000000000276 ) ) ; +#79792 = SURFACE_STYLE_FILL_AREA ( #48652 ) ; +#79793 = EDGE_CURVE ( 'NONE', #8544, #93530, #92979, .T. ) ; +#79794 = ORIENTED_EDGE ( 'NONE', *, *, #97634, .F. ) ; +#79795 = FILL_AREA_STYLE_COLOUR ( '', #39481 ) ; +#79796 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666653285, 0.5000000000000000000, 3.495651678170078205E-76 ) ) ; +#79797 = LINE ( 'NONE', #24686, #89500 ) ; +#79798 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#79799 = ORIENTED_EDGE ( 'NONE', *, *, #2646, .F. ) ; +#79800 = AXIS2_PLACEMENT_3D ( 'NONE', #57502, #35027, #88607 ) ; +#79801 = VERTEX_POINT ( 'NONE', #62411 ) ; +#79802 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55178 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66199, #10975, #3424 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79803 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#79804 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79805 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#79806 = ORIENTED_EDGE ( 'NONE', *, *, #54368, .F. ) ; +#79807 = LINE ( 'NONE', #80827, #6540 ) ; +#79808 = VECTOR ( 'NONE', #82068, 1000.000000000000000 ) ; +#79810 = FILL_AREA_STYLE_COLOUR ( '', #11935 ) ; +#79809 = AXIS2_PLACEMENT_3D ( 'NONE', #66091, #27294, #22631 ) ; +#79811 = ORIENTED_EDGE ( 'NONE', *, *, #76131, .F. ) ; +#79812 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79813 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16134 ), #74925 ) ; +#79814 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79816 = EDGE_CURVE ( 'NONE', #55852, #45519, #69009, .T. ) ; +#79815 = ORIENTED_EDGE ( 'NONE', *, *, #59479, .T. ) ; +#79817 = VECTOR ( 'NONE', #76899, 1000.000000000000000 ) ; +#79818 = CYLINDRICAL_SURFACE ( 'NONE', #64449, 0.05000000000000012768 ) ; +#79819 = PRESENTATION_STYLE_ASSIGNMENT (( #18505 ) ) ; +#79820 = FILL_AREA_STYLE ('',( #63986 ) ) ; +#79821 = COLOUR_RGB ( '',0.6666666666666666297, 0.6666666666666666297, 0.6666666666666666297 ) ; +#79822 = SURFACE_STYLE_USAGE ( .BOTH. , #48168 ) ; +#79823 = PRESENTATION_STYLE_ASSIGNMENT (( #96606 ) ) ; +#79824 = ORIENTED_EDGE ( 'NONE', *, *, #58091, .T. ) ; +#79826 = ORIENTED_EDGE ( 'NONE', *, *, #29396, .T. ) ; +#79825 = VERTEX_POINT ( 'NONE', #53726 ) ; +#79827 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79828 = ADVANCED_FACE ( 'NONE', ( #85874 ), #24120, .T. ) ; +#79829 = ORIENTED_EDGE ( 'NONE', *, *, #56398, .F. ) ; +#79830 = CIRCLE ( 'NONE', #53787, 0.009999999999999998473 ) ; +#79831 = VECTOR ( 'NONE', #12339, 1000.000000000000000 ) ; +#79832 = EDGE_LOOP ( 'NONE', ( #35404, #86595, #94082, #89166 ) ) ; +#79834 = ORIENTED_EDGE ( 'NONE', *, *, #71278, .T. ) ; +#79833 = FACE_OUTER_BOUND ( 'NONE', #73137, .T. ) ; +#79835 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39841 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16159, #17180, #33553 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79836 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79837 = SURFACE_STYLE_FILL_AREA ( #8274 ) ; +#79838 = STYLED_ITEM ( 'NONE', ( #26001 ), #616 ) ; +#79839 = ORIENTED_EDGE ( 'NONE', *, *, #80245, .T. ) ; +#79840 = LINE ( 'NONE', #64509, #6394 ) ; +#79841 = PLANE ( 'NONE', #31324 ) ; +#79842 = ORIENTED_EDGE ( 'NONE', *, *, #98863, .T. ) ; +#79843 = EDGE_CURVE ( 'NONE', #30288, #47667, #55759, .T. ) ; +#79844 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#79845 = ADVANCED_FACE ( 'NONE', ( #32269 ), #23593, .F. ) ; +#79846 = CARTESIAN_POINT ( 'NONE', ( 7.817401000000000266, 10.37243800000000071, 0.8991599999999999593 ) ) ; +#79847 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.149999999999999911, 0.000000000000000000 ) ) ; +#79848 = FILL_AREA_STYLE_COLOUR ( '', #2709 ) ; +#79849 = ORIENTED_EDGE ( 'NONE', *, *, #52766, .F. ) ; +#79850 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1142 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9708, #1645, #95528 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79851 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.1900000000000000022 ) ) ; +#79852 = EDGE_LOOP ( 'NONE', ( #82215, #83791, #89334, #37851 ) ) ; +#79853 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#79854 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63538 ) ) ; +#79855 = FACE_OUTER_BOUND ( 'NONE', #33104, .T. ) ; +#79856 = LINE ( 'NONE', #71680, #19655 ) ; +#79857 = VECTOR ( 'NONE', #84536, 1000.000000000000000 ) ; +#79858 = FILL_AREA_STYLE ('',( #72184 ) ) ; +#79859 = EDGE_CURVE ( 'NONE', #88953, #69281, #10694, .T. ) ; +#79860 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79861 = PRESENTATION_STYLE_ASSIGNMENT (( #40561 ) ) ; +#79863 = FACE_OUTER_BOUND ( 'NONE', #24335, .T. ) ; +#79862 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79864 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79865 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47185 ), #52104 ) ; +#79866 = CARTESIAN_POINT ( 'NONE', ( -0.9345478915627419836, -1.069424818316000003, 0.8299999999999999600 ) ) ; +#79867 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#79868 = ORIENTED_EDGE ( 'NONE', *, *, #45720, .T. ) ; +#79869 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#79870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79871 = LINE ( 'NONE', #63556, #55883 ) ; +#79872 = VECTOR ( 'NONE', #27477, 1000.000000000000114 ) ; +#79873 = EDGE_CURVE ( 'NONE', #61237, #22953, #57799, .T. ) ; +#79874 = VECTOR ( 'NONE', #961, 1000.000000000000000 ) ; +#79875 = SURFACE_STYLE_USAGE ( .BOTH. , #72199 ) ; +#79876 = VERTEX_POINT ( 'NONE', #41949 ) ; +#79877 = PLANE ( 'NONE', #31616 ) ; +#79879 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#79878 = CARTESIAN_POINT ( 'NONE', ( -1.476179938779914602, 3.099999999999990319, -0.02000000000000000042 ) ) ; +#79880 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#79881 = AXIS2_PLACEMENT_3D ( 'NONE', #8147, #67984, #29218 ) ; +#79882 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146550232, 0.5686465759269649922, 0.8100000000000000533 ) ) ; +#79883 = CARTESIAN_POINT ( 'NONE', ( 0.2550745812975909743, -1.387940725880749904, 0.8299999999999999600 ) ) ; +#79884 = VECTOR ( 'NONE', #23666, 1000.000000000000114 ) ; +#79885 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34040 ), #35870 ) ; +#79886 = VECTOR ( 'NONE', #12321, 1000.000000000000000 ) ; +#79887 = CARTESIAN_POINT ( 'NONE', ( -1.207523339372349902, -1.437310919031880241, 0.8299999999999998490 ) ) ; +#79888 = CARTESIAN_POINT ( 'NONE', ( -5.421010862427522170E-17, 0.2999999999815373686, -1.665334536835250932E-17 ) ) ; +#79889 = VECTOR ( 'NONE', #252, 1000.000000000000114 ) ; +#79890 = FACE_OUTER_BOUND ( 'NONE', #44387, .T. ) ; +#79891 = ORIENTED_EDGE ( 'NONE', *, *, #17224, .F. ) ; +#79892 = SURFACE_STYLE_FILL_AREA ( #8823 ) ; +#79893 = STYLED_ITEM ( 'NONE', ( #73292 ), #6376 ) ; +#79894 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#79895 = PRESENTATION_STYLE_ASSIGNMENT (( #32412 ) ) ; +#79896 = PRESENTATION_STYLE_ASSIGNMENT (( #17559 ) ) ; +#79897 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 1.149999999999999911, 0.000000000000000000 ) ) ; +#79898 = LINE ( 'NONE', #88542, #51770 ) ; +#79899 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30021 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13751, #28629, #44916 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#79900 = EDGE_CURVE ( 'NONE', #93582, #81120, #34805, .T. ) ; +#79901 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49097, #97011, #87874, #25130 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79902 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79903 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79904 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79905 = SURFACE_STYLE_FILL_AREA ( #87045 ) ; +#79906 = EDGE_CURVE ( 'NONE', #1951, #6445, #97025, .T. ) ; +#79907 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#79908 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79909 = VECTOR ( 'NONE', #21832, 1000.000000000000000 ) ; +#79910 = CARTESIAN_POINT ( 'NONE', ( -0.08340097402597416998, 0.6899999999999999467, 0.2077922077922079724 ) ) ; +#79911 = AXIS2_PLACEMENT_3D ( 'NONE', #51386, #65174, #4386 ) ; +#79912 = ORIENTED_EDGE ( 'NONE', *, *, #56398, .T. ) ; +#79913 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79914 = VERTEX_POINT ( 'NONE', #34309 ) ; +#79915 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30798, 'distance_accuracy_value', 'NONE'); +#79916 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10736, 'distance_accuracy_value', 'NONE'); +#79917 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19539 ), #35893 ) ; +#79918 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79919 = CARTESIAN_POINT ( 'NONE', ( 0.1662790904141970283, -1.409021472795120022, 0.8100000000000000533 ) ) ; +#79920 = LINE ( 'NONE', #33453, #94852 ) ; +#79921 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#79922 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#79923 = ADVANCED_FACE ( 'NONE', ( #10176 ), #57279, .F. ) ; +#79924 = VERTEX_POINT ( 'NONE', #18938 ) ; +#79925 = FACE_OUTER_BOUND ( 'NONE', #44780, .T. ) ; +#79926 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78056, 'distance_accuracy_value', 'NONE'); +#79927 = LINE ( 'NONE', #75752, #6755 ) ; +#79928 = FILL_AREA_STYLE_COLOUR ( '', #82956 ) ; +#79929 = ORIENTED_EDGE ( 'NONE', *, *, #17438, .F. ) ; +#79930 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79931 = CARTESIAN_POINT ( 'NONE', ( -1.222915055115519900, -1.432449005990839908, 0.8299999999999999600 ) ) ; +#79932 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.016666666666666829, 0.000000000000000000 ) ) ; +#79933 = MANIFOLD_SOLID_BREP ( 'ÊäÈë34', #35614 ) ; +#79934 = ORIENTED_EDGE ( 'NONE', *, *, #52115, .T. ) ; +#79935 = SURFACE_SIDE_STYLE ('',( #55457 ) ) ; +#79936 = AXIS2_PLACEMENT_3D ( 'NONE', #1296, #96210, #57979 ) ; +#79937 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#79938 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65138, 'distance_accuracy_value', 'NONE'); +#79939 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#79940 = LINE ( 'NONE', #94198, #75252 ) ; +#79941 = VERTEX_POINT ( 'NONE', #27645 ) ; +#79942 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79943 = VECTOR ( 'NONE', #83306, 1000.000000000000000 ) ; +#79944 = SURFACE_SIDE_STYLE ('',( #17118 ) ) ; +#79945 = CARTESIAN_POINT ( 'NONE', ( -1.353661290370536951, -1.131943244623368372, 0.8099999999998910294 ) ) ; +#79946 = LINE ( 'NONE', #64116, #79347 ) ; +#79947 = PRESENTATION_STYLE_ASSIGNMENT (( #55471 ) ) ; +#79948 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79949 = ADVANCED_FACE ( 'NONE', ( #89894 ), #19456, .T. ) ; +#79950 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #43306, #82630 ), + ( #97398, #67281 ), + ( #96904, #36180 ), + ( #57677, #73965 ), + ( #74968, #96402 ), + ( #4491, #26503 ), + ( #82142, #20831 ), + ( #19832, #34680 ), + ( #27512, #11073 ), + ( #59182, #88776 ), + ( #90271, #50003 ), + ( #12595, #90789 ), + ( #27009, #20318 ), + ( #3006, #34180 ), + ( #42324, #58173 ), + ( #58668, #65805 ), + ( #65283, #89769 ), + ( #19317, #50509 ), + ( #11579, #42816 ), + ( #69245, #37177 ), + ( #7433, #76450 ), + ( #98845, #45777 ), + ( #84624, #13088 ), + ( #21834, #100321 ), + ( #38658, #77450 ), + ( #68280, #52999 ), + ( #99347, #60658 ), + ( #6449, #67773 ), + ( #76963, #6924 ), + ( #29498, #99820 ), + ( #91756, #5462 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.04097893070594339771, 0.07886041624184260412, 0.1139485695848140023, 0.1469181589410820110, 0.1789789957062060122, 0.2102877319658280064, 0.2417150887787909985, 0.2734982334250919966, 0.3056144908655740178, 0.3382864838163350263, 0.3715855336697960198, 0.4057812349280769948, 0.4753309549031530246, 0.5451735204053850259, 0.6145171970331100297, 0.6824659191102320221, 0.7153232889272269635, 0.7466521175711759994, 0.7768360883787870375, 0.8055560270855229854, 0.8327754294448449501, 0.8584535229925359667, 0.8825485238002289679, 0.9057267804332469474, 0.9282330950246560075, 0.9509427184471550554, 0.9744340267434640213, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79951 = STYLED_ITEM ( 'NONE', ( #17642 ), #86190 ) ; +#79952 = STYLED_ITEM ( 'NONE', ( #25857 ), #93586 ) ; +#79953 = STYLED_ITEM ( 'NONE', ( #5107 ), #94978 ) ; +#79954 = VERTEX_POINT ( 'NONE', #83260 ) ; +#79956 = EDGE_LOOP ( 'NONE', ( #95451, #86788, #62043, #37281 ) ) ; +#79955 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#79957 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #54551, #8469, #14669, #31547, #62215, #55054, #47879, #70857 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000002776, 0.5000000000000005551, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#79958 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22881 ) ) ; +#79959 = SURFACE_STYLE_USAGE ( .BOTH. , #18633 ) ; +#79960 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#79961 = FACE_OUTER_BOUND ( 'NONE', #7650, .T. ) ; +#79962 = CARTESIAN_POINT ( 'NONE', ( -1.016666666666666829, 3.099999999999989875, 0.000000000000000000 ) ) ; +#79963 = VERTEX_POINT ( 'NONE', #42932 ) ; +#79964 = ADVANCED_FACE ( 'NONE', ( #90394 ), #28615, .F. ) ; +#79965 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94571 ) ) ; +#79966 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68483 ) ) ; +#79967 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#79968 = ORIENTED_EDGE ( 'NONE', *, *, #8762, .F. ) ; +#79969 = AXIS2_PLACEMENT_3D ( 'NONE', #5360, #37571, #89676 ) ; +#79970 = EDGE_CURVE ( 'NONE', #87203, #19644, #29610, .T. ) ; +#79972 = PRESENTATION_STYLE_ASSIGNMENT (( #7896 ) ) ; +#79971 = LINE ( 'NONE', #93703, #42262 ) ; +#79973 = VERTEX_POINT ( 'NONE', #59812 ) ; +#79974 = EDGE_LOOP ( 'NONE', ( #98801, #75881, #12803, #34892 ) ) ; +#79975 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#79977 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#79976 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79978 = VECTOR ( 'NONE', #78468, 1000.000000000000000 ) ; +#79979 = LINE ( 'NONE', #47292, #66874 ) ; +#79980 = VECTOR ( 'NONE', #96173, 1000.000000000000114 ) ; +#79981 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#79982 = ORIENTED_EDGE ( 'NONE', *, *, #49036, .T. ) ; +#79983 = VECTOR ( 'NONE', #18760, 1000.000000000000000 ) ; +#79984 = STYLED_ITEM ( 'NONE', ( #41967 ), #43122 ) ; +#79985 = EDGE_CURVE ( 'NONE', #40624, #77521, #66419, .T. ) ; +#79986 = VERTEX_POINT ( 'NONE', #20446 ) ; +#79987 = CARTESIAN_POINT ( 'NONE', ( 1.343121150739609915, -1.400043273498609908, 0.8100000000000000533 ) ) ; +#79988 = VERTEX_POINT ( 'NONE', #78098 ) ; +#79989 = VERTEX_POINT ( 'NONE', #45401 ) ; +#79990 = PRESENTATION_STYLE_ASSIGNMENT (( #10940 ) ) ; +#79991 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#79992 = CARTESIAN_POINT ( 'NONE', ( -1.005723260889149984, -1.285676881280640282, 0.8299999999999999600 ) ) ; +#79993 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#79994 = EDGE_CURVE ( 'NONE', #46905, #79988, #85243, .T. ) ; +#79995 = FILL_AREA_STYLE_COLOUR ( '', #33451 ) ; +#79996 = AXIS2_PLACEMENT_3D ( 'NONE', #10446, #8962, #78484 ) ; +#79997 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#79999 = LINE ( 'NONE', #9932, #70359 ) ; +#79998 = VECTOR ( 'NONE', #6353, 1000.000000000000000 ) ; +#80000 = LINE ( 'NONE', #15639, #11071 ) ; +#80001 = SURFACE_STYLE_USAGE ( .BOTH. , #23864 ) ; +#80002 = ORIENTED_EDGE ( 'NONE', *, *, #82532, .T. ) ; +#80003 = LINE ( 'NONE', #9938, #14249 ) ; +#80004 = ADVANCED_FACE ( 'NONE', ( #38297 ), #43300, .F. ) ; +#80006 = SURFACE_STYLE_FILL_AREA ( #96278 ) ; +#80005 = SURFACE_SIDE_STYLE ('',( #34559 ) ) ; +#80007 = FACE_OUTER_BOUND ( 'NONE', #12674, .T. ) ; +#80008 = FILL_AREA_STYLE ('',( #87648 ) ) ; +#80009 = CYLINDRICAL_SURFACE ( 'NONE', #91919, 0.1100000000000007222 ) ; +#80010 = SURFACE_SIDE_STYLE ('',( #88159 ) ) ; +#80011 = LINE ( 'NONE', #96782, #32277 ) ; +#80012 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.1600000000000000033, -1.250000000000000000 ) ) ; +#80013 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #57146 ) ) ; +#80014 = VERTEX_POINT ( 'NONE', #8553 ) ; +#80015 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.4700000000282762436, 0.6499230723708768753 ) ) ; +#80016 = SURFACE_SIDE_STYLE ('',( #56032 ) ) ; +#80017 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#80018 = SURFACE_SIDE_STYLE ('',( #78992 ) ) ; +#80019 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80020 = AXIS2_PLACEMENT_3D ( 'NONE', #279, #92669, #16580 ) ; +#80021 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77799, 'distance_accuracy_value', 'NONE'); +#80022 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#80023 = SURFACE_SIDE_STYLE ('',( #2405 ) ) ; +#80024 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80025 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80026 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80027 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99497 ) ) ; +#80028 = EDGE_CURVE ( 'NONE', #30348, #43411, #14241, .T. ) ; +#80029 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#80030 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#80031 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80032 = LINE ( 'NONE', #18189, #664 ) ; +#80033 = VECTOR ( 'NONE', #82114, 1000.000000000000000 ) ; +#80034 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22948 ), #21330 ) ; +#80035 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80036 = LINE ( 'NONE', #41228, #4677 ) ; +#80037 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80038 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80039 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #94512, 'design' ) ; +#80040 = STYLED_ITEM ( 'NONE', ( #3073 ), #81757 ) ; +#80041 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80042 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 11.25741999999999976, 0.8648700000000000276 ) ) ; +#80043 = EDGE_CURVE ( 'NONE', #85200, #32231, #9075, .T. ) ; +#80044 = EDGE_LOOP ( 'NONE', ( #50483, #35179, #20978, #46902 ) ) ; +#80045 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80046 = VECTOR ( 'NONE', #23305, 1000.000000000000000 ) ; +#80047 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000971, 0.1499999999999999944 ) ) ; +#80048 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80049 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16149, 'distance_accuracy_value', 'NONE'); +#80051 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1000000000000000056, -11.41999999999999993 ) ) ; +#80050 = PLANE ( 'NONE', #42775 ) ; +#80052 = EDGE_CURVE ( 'NONE', #20861, #89578, #11077, .T. ) ; +#80053 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#80054 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#80055 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22969 ), #75092 ) ; +#80056 = ORIENTED_EDGE ( 'NONE', *, *, #10013, .T. ) ; +#80058 = EDGE_CURVE ( 'NONE', #18378, #28251, #18294, .T. ) ; +#80057 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80059 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9829 ) ) ; +#80060 = SURFACE_STYLE_USAGE ( .BOTH. , #8477 ) ; +#80061 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80062 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69049, 'distance_accuracy_value', 'NONE'); +#80063 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54236, 'distance_accuracy_value', 'NONE'); +#80064 = FILL_AREA_STYLE_COLOUR ( '', #27259 ) ; +#80065 = SURFACE_STYLE_USAGE ( .BOTH. , #17727 ) ; +#80066 = ORIENTED_EDGE ( 'NONE', *, *, #73805, .T. ) ; +#80067 = ORIENTED_EDGE ( 'NONE', *, *, #71548, .T. ) ; +#80068 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80069 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#80070 = ORIENTED_EDGE ( 'NONE', *, *, #72742, .T. ) ; +#80072 = SURFACE_STYLE_USAGE ( .BOTH. , #32587 ) ; +#80071 = AXIS2_PLACEMENT_3D ( 'NONE', #14526, #53885, #21228 ) ; +#80073 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#80074 = PRESENTATION_STYLE_ASSIGNMENT (( #25446 ) ) ; +#80075 = CARTESIAN_POINT ( 'NONE', ( -1.370884097750779906, -1.038425069758839969, 0.8299999999999997380 ) ) ; +#80077 = EDGE_CURVE ( 'NONE', #68224, #74727, #3523, .T. ) ; +#80076 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14265 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62484, #94061, #60602 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80078 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #19536 ) ; +#80079 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#80081 = ORIENTED_EDGE ( 'NONE', *, *, #63186, .F. ) ; +#80080 = VERTEX_POINT ( 'NONE', #34684 ) ; +#80082 = ORIENTED_EDGE ( 'NONE', *, *, #27305, .F. ) ; +#80083 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80084 = CARTESIAN_POINT ( 'NONE', ( 1.419155844155840063, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#80085 = ORIENTED_EDGE ( 'NONE', *, *, #56078, .T. ) ; +#80086 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80087 = LINE ( 'NONE', #88726, #76667 ) ; +#80088 = ADVANCED_FACE ( 'NONE', ( #65288 ), #71956, .T. ) ; +#80089 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45761 ), #99569 ) ; +#80090 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84928 ), #75198 ) ; +#80091 = EDGE_LOOP ( 'NONE', ( #1439, #91814, #99530, #4003 ) ) ; +#80092 = ORIENTED_EDGE ( 'NONE', *, *, #21973, .T. ) ; +#80094 = SURFACE_STYLE_USAGE ( .BOTH. , #9031 ) ; +#80093 = CYLINDRICAL_SURFACE ( 'NONE', #95935, 0.2000000000000005107 ) ; +#80095 = EDGE_LOOP ( 'NONE', ( #10681, #31327, #16366, #57007 ) ) ; +#80096 = VERTEX_POINT ( 'NONE', #55648 ) ; +#80097 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -4.344024262657780003E-34 ) ) ; +#80098 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24825 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #77183, #7158, #21559 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80099 = FILL_AREA_STYLE ('',( #32622 ) ) ; +#80100 = MANIFOLD_SOLID_BREP ( 'ÊäÈë37', #12701 ) ; +#80101 = PRESENTATION_STYLE_ASSIGNMENT (( #17764 ) ) ; +#80102 = CIRCLE ( 'NONE', #97942, 0.5799999999999999600 ) ; +#80104 = ORIENTED_EDGE ( 'NONE', *, *, #64877, .T. ) ; +#80103 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01500000000000000118, 0.2400000000000000189 ) ) ; +#80105 = FACE_OUTER_BOUND ( 'NONE', #57742, .T. ) ; +#80106 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80107 = VECTOR ( 'NONE', #61421, 1000.000000000000000 ) ; +#80108 = CARTESIAN_POINT ( 'NONE', ( -0.2582749839912160117, -0.9663557550577259736, 0.8299999999999999600 ) ) ; +#80109 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#80110 = ORIENTED_EDGE ( 'NONE', *, *, #29673, .F. ) ; +#80112 = PRESENTATION_STYLE_ASSIGNMENT (( #41305 ) ) ; +#80111 = PRESENTATION_STYLE_ASSIGNMENT (( #11054 ) ) ; +#80113 = ORIENTED_EDGE ( 'NONE', *, *, #11789, .F. ) ; +#80114 = ORIENTED_EDGE ( 'NONE', *, *, #69888, .F. ) ; +#80116 = PRESENTATION_STYLE_ASSIGNMENT (( #94868 ) ) ; +#80115 = SURFACE_STYLE_FILL_AREA ( #64270 ) ; +#80117 = VECTOR ( 'NONE', #23181, 1000.000000000000000 ) ; +#80118 = PRESENTATION_STYLE_ASSIGNMENT (( #79099 ) ) ; +#80120 = EDGE_CURVE ( 'NONE', #35498, #15064, #79633, .T. ) ; +#80119 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80121 = VECTOR ( 'NONE', #21745, 1000.000000000000000 ) ; +#80122 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#80123 = STYLED_ITEM ( 'NONE', ( #51145 ), #65898 ) ; +#80124 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 7.099999999999999645, 0.000000000000000000 ) ) ; +#80125 = FACE_OUTER_BOUND ( 'NONE', #25614, .T. ) ; +#80126 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#80127 = ADVANCED_FACE ( 'NONE', ( #95396 ), #33672, .T. ) ; +#80128 = FILL_AREA_STYLE ('',( #1497 ) ) ; +#80129 = ORIENTED_EDGE ( 'NONE', *, *, #36604, .T. ) ; +#80130 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#80131 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80132 = EDGE_LOOP ( 'NONE', ( #84934, #52090, #48312, #75304 ) ) ; +#80133 = ADVANCED_FACE ( 'NONE', ( #51004 ), #100201, .T. ) ; +#80134 = AXIS2_PLACEMENT_3D ( 'NONE', #32228, #80718, #50087 ) ; +#80135 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80136 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.6600000000000000311, -0.7999999999999999334 ) ) ; +#80138 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80137 = CARTESIAN_POINT ( 'NONE', ( -0.9899999999999999911, -9.880000000000000782, 0.3499999999999999778 ) ) ; +#80139 = SURFACE_STYLE_FILL_AREA ( #42328 ) ; +#80140 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8648700000000000276 ) ) ; +#80141 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80142 = FILL_AREA_STYLE_COLOUR ( '', #96569 ) ; +#80143 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.7000000000000018430, -1.195472123049164304E-89 ) ) ; +#80144 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80145 = LINE ( 'NONE', #17306, #26659 ) ; +#80146 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80147 = PLANE ( 'NONE', #100434 ) ; +#80148 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58948 ), #21434 ) ; +#80149 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80150 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23065 ) ) ; +#80151 = SURFACE_SIDE_STYLE ('',( #95410 ) ) ; +#80152 = EDGE_CURVE ( 'NONE', #18766, #54937, #42820, .T. ) ; +#80153 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80154 = SURFACE_STYLE_USAGE ( .BOTH. , #95413 ) ; +#80155 = VECTOR ( 'NONE', #70226, 1000.000000000000000 ) ; +#80156 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28171, 'distance_accuracy_value', 'NONE'); +#80157 = ORIENTED_EDGE ( 'NONE', *, *, #65000, .F. ) ; +#80158 = LINE ( 'NONE', #49011, #18227 ) ; +#80159 = CARTESIAN_POINT ( 'NONE', ( 1.696022727272729957, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#80160 = ORIENTED_EDGE ( 'NONE', *, *, #43528, .F. ) ; +#80161 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80162 = LINE ( 'NONE', #17325, #72510 ) ; +#80163 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80164 = FILL_AREA_STYLE ('',( #33182 ) ) ; +#80165 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.000000000000000000 ) ) ; +#80166 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100935 ) ; +#80167 = STYLED_ITEM ( 'NONE', ( #2381 ), #86823 ) ; +#80168 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80169 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80170 = ORIENTED_EDGE ( 'NONE', *, *, #61234, .F. ) ; +#80171 = VERTEX_POINT ( 'NONE', #73967 ) ; +#80172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80173 = EDGE_CURVE ( 'NONE', #94831, #76986, #58673, .T. ) ; +#80174 = VECTOR ( 'NONE', #83745, 1000.000000000000114 ) ; +#80175 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#80176 = DIRECTION ( 'NONE', ( 5.551115123125780237E-17, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#80177 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84759 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88151, #20183, #59045 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80179 = DIRECTION ( 'NONE', ( 0.7071060119555145906, 0.7071075504167436687, 0.000000000000000000 ) ) ; +#80180 = CARTESIAN_POINT ( 'NONE', ( 4.915000004213077034E-07, -1.182000001348493257E-07, 0.02000000000000005246 ) ) ; +#80181 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#80182 = EDGE_CURVE ( 'NONE', #42509, #17853, #74477, .T. ) ; +#80183 = VERTEX_POINT ( 'NONE', #46157 ) ; +#80184 = SURFACE_STYLE_USAGE ( .BOTH. , #49035 ) ; +#80185 = VECTOR ( 'NONE', #55743, 1000.000000000000000 ) ; +#80186 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80187 = ORIENTED_EDGE ( 'NONE', *, *, #56969, .T. ) ; +#80188 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80189 = SURFACE_SIDE_STYLE ('',( #87823 ) ) ; +#80190 = VECTOR ( 'NONE', #9107, 1000.000000000000000 ) ; +#80191 = ORIENTED_EDGE ( 'NONE', *, *, #97143, .T. ) ; +#80192 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80193 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80194 = ADVANCED_FACE ( 'NONE', ( #14505 ), #35684, .T. ) ; +#80195 = EDGE_CURVE ( 'NONE', #40624, #9730, #25272, .T. ) ; +#80196 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27327, #81476, #74786, #19651 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80197 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80198 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#80199 = SURFACE_STYLE_USAGE ( .BOTH. , #57226 ) ; +#80200 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, -3.738329090730020644E-17, -0.8499999999999999778 ) ) ; +#80201 = CARTESIAN_POINT ( 'NONE', ( 0.9399999999999999467, -9.880000000000000782, 0.2500000000000000000 ) ) ; +#80203 = ORIENTED_EDGE ( 'NONE', *, *, #75029, .T. ) ; +#80202 = ORIENTED_EDGE ( 'NONE', *, *, #79421, .F. ) ; +#80204 = PRESENTATION_STYLE_ASSIGNMENT (( #27085 ) ) ; +#80205 = EDGE_CURVE ( 'NONE', #51624, #72320, #62050, .T. ) ; +#80206 = EDGE_CURVE ( 'NONE', #39936, #84475, #1774, .T. ) ; +#80207 = ORIENTED_EDGE ( 'NONE', *, *, #9312, .F. ) ; +#80208 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#80209 = ORIENTED_EDGE ( 'NONE', *, *, #6148, .T. ) ; +#80210 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80211 = ORIENTED_EDGE ( 'NONE', *, *, #59052, .F. ) ; +#80212 = LINE ( 'NONE', #40395, #82461 ) ; +#80213 = ADVANCED_FACE ( 'NONE', ( #8816 ), #55900, .T. ) ; +#80214 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80215 = CARTESIAN_POINT ( 'NONE', ( -0.1988983467373149905, -1.000931601726380071, 0.8300000000000000711 ) ) ; +#80216 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50170 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46177, #100216, #47224 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80218 = SURFACE_STYLE_FILL_AREA ( #58751 ) ; +#80217 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80219 = ORIENTED_EDGE ( 'NONE', *, *, #57834, .F. ) ; +#80220 = ORIENTED_EDGE ( 'NONE', *, *, #38240, .T. ) ; +#80221 = EDGE_CURVE ( 'NONE', #81337, #7585, #64052, .T. ) ; +#80222 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80223 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80224 = VERTEX_POINT ( 'NONE', #31887 ) ; +#80225 = LINE ( 'NONE', #4579, #94873 ) ; +#80226 = STYLED_ITEM ( 'NONE', ( #44596 ), #45620 ) ; +#80228 = ORIENTED_EDGE ( 'NONE', *, *, #93009, .T. ) ; +#80227 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80229 = CARTESIAN_POINT ( 'NONE', ( 11.33879300000000079, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#80230 = VERTEX_POINT ( 'NONE', #69657 ) ; +#80231 = CARTESIAN_POINT ( 'NONE', ( -0.05957252635663159990, -1.226312279485590073, 0.8100000000000000533 ) ) ; +#80232 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80233 = ORIENTED_EDGE ( 'NONE', *, *, #52473, .T. ) ; +#80234 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6892893218813452849, -1.100000000000000089 ) ) ; +#80235 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80236 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80237 = SURFACE_STYLE_USAGE ( .BOTH. , #40425 ) ; +#80238 = VECTOR ( 'NONE', #58087, 1000.000000000000000 ) ; +#80239 = FILL_AREA_STYLE ('',( #17901 ) ) ; +#80240 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#80241 = VERTEX_POINT ( 'NONE', #95145 ) ; +#80242 = CARTESIAN_POINT ( 'NONE', ( 1.562899685023940277, -1.469666695271939938, 0.8099999999999982769 ) ) ; +#80243 = PLANE ( 'NONE', #36533 ) ; +#80244 = VERTEX_POINT ( 'NONE', #87030 ) ; +#80245 = EDGE_CURVE ( 'NONE', #89492, #34323, #55524, .T. ) ; +#80246 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80247 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 1.696237999999999913, 0.8648700000000000276 ) ) ; +#80248 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80249 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80250 = SURFACE_STYLE_USAGE ( .BOTH. , #23590 ) ; +#80251 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87579 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6876, #70759, #69736 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80252 = CARTESIAN_POINT ( 'NONE', ( 0.3999999999999998557, 0.7578679656440356904, -0.1999999999999999278 ) ) ; +#80253 = EDGE_CURVE ( 'NONE', #60864, #64829, #730, .T. ) ; +#80254 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80255 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, -0.09999999999999988065, 0.000000000000000000 ) ) ; +#80256 = SURFACE_SIDE_STYLE ('',( #97026 ) ) ; +#80257 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80258 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80259 = VECTOR ( 'NONE', #8983, 1000.000000000000000 ) ; +#80260 = SURFACE_SIDE_STYLE ('',( #1641 ) ) ; +#80261 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80262 = ORIENTED_EDGE ( 'NONE', *, *, #19533, .T. ) ; +#80263 = VECTOR ( 'NONE', #17580, 1000.000000000000000 ) ; +#80264 = SURFACE_SIDE_STYLE ('',( #87395 ) ) ; +#80265 = EDGE_CURVE ( 'NONE', #73059, #64535, #57027, .T. ) ; +#80266 = FILL_AREA_STYLE_COLOUR ( '', #55964 ) ; +#80267 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80268 = VECTOR ( 'NONE', #95612, 1000.000000000000000 ) ; +#80269 = SURFACE_SIDE_STYLE ('',( #72577 ) ) ; +#80270 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80271 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96178, 'distance_accuracy_value', 'NONE'); +#80272 = VERTEX_POINT ( 'NONE', #79880 ) ; +#80273 = EDGE_CURVE ( 'NONE', #34152, #25531, #40058, .T. ) ; +#80274 = SURFACE_SIDE_STYLE ('',( #4154 ) ) ; +#80275 = LINE ( 'NONE', #13237, #24984 ) ; +#80276 = CARTESIAN_POINT ( 'NONE', ( 8.665929124874956813, 3.159949124874956272, 0.8991599999999999593 ) ) ; +#80277 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99001 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16419, #76730, #121 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80278 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #42438, #13206, #89879, #3624 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80279 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8648700000000000276 ) ) ; +#80280 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80281 = PLANE ( 'NONE', #27657 ) ; +#80282 = ORIENTED_EDGE ( 'NONE', *, *, #80028, .F. ) ; +#80283 = SURFACE_STYLE_FILL_AREA ( #95048 ) ; +#80284 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15700 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35630, #83579, #59637 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80285 = ORIENTED_EDGE ( 'NONE', *, *, #25116, .F. ) ; +#80286 = EDGE_CURVE ( 'NONE', #9919, #21238, #24256, .T. ) ; +#80287 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48921, 'distance_accuracy_value', 'NONE'); +#80288 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80289 = CARTESIAN_POINT ( 'NONE', ( -0.2109871940610940078, -1.020192282374009940, 0.8299999999999999600 ) ) ; +#80290 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80291 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8100000000000000533 ) ) ; +#80292 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#80293 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85204 ), #65702 ) ; +#80294 = EDGE_CURVE ( 'NONE', #44999, #93886, #54379, .T. ) ; +#80295 = ORIENTED_EDGE ( 'NONE', *, *, #75880, .F. ) ; +#80296 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80297 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 4.291319999999999801, 0.8648700000000000276 ) ) ; +#80298 = FILL_AREA_STYLE_COLOUR ( '', #3647 ) ; +#80299 = VERTEX_POINT ( 'NONE', #87520 ) ; +#80300 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80301 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46037 ), #67220 ) ; +#80302 = AXIS2_PLACEMENT_3D ( 'NONE', #97821, #66725, #74409 ) ; +#80303 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#80304 = VERTEX_POINT ( 'NONE', #93618 ) ; +#80305 = STYLED_ITEM ( 'NONE', ( #44265 ), #59937 ) ; +#80306 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, 0.000000000000000000 ) ) ; +#80307 = EDGE_CURVE ( 'NONE', #28424, #55576, #48741, .T. ) ; +#80308 = STYLED_ITEM ( 'NONE', ( #92055 ), #36445 ) ; +#80309 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78120 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52294, #20104, #43588 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80310 = SURFACE_SIDE_STYLE ('',( #40502 ) ) ; +#80311 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#80312 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.008431457505076156086, -0.1458578643762691029 ) ) ; +#80313 = EDGE_LOOP ( 'NONE', ( #76595, #28473, #31251, #44173 ) ) ; +#80314 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73671, #9779, #96112 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80316 = EDGE_CURVE ( 'NONE', #80960, #4944, #15521, .T. ) ; +#80315 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.2999999999999989897, -0.02000000000001673356 ) ) ; +#80317 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37882 ), #49325 ) ; +#80318 = EDGE_CURVE ( 'NONE', #51059, #86316, #47198, .T. ) ; +#80319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80320 = EDGE_LOOP ( 'NONE', ( #28046, #96168, #24778, #80332 ) ) ; +#80321 = FILL_AREA_STYLE ('',( #43495 ) ) ; +#80322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1819 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65616, #28334, #12921 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80323 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8442 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79105, #46914, #9059 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80324 = ORIENTED_EDGE ( 'NONE', *, *, #61695, .T. ) ; +#80325 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #80143, #95402, #32151, #86768 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80327 = EDGE_CURVE ( 'NONE', #19424, #61112, #34910, .T. ) ; +#80326 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80328 = SURFACE_SIDE_STYLE ('',( #97593 ) ) ; +#80329 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#80330 = SURFACE_SIDE_STYLE ('',( #82337 ) ) ; +#80331 = ORIENTED_EDGE ( 'NONE', *, *, #53499, .F. ) ; +#80333 = ORIENTED_EDGE ( 'NONE', *, *, #79603, .T. ) ; +#80332 = ORIENTED_EDGE ( 'NONE', *, *, #98465, .F. ) ; +#80334 = VERTEX_POINT ( 'NONE', #88029 ) ; +#80335 = ADVANCED_FACE ( 'NONE', ( #80384 ), #80789, .F. ) ; +#80336 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16879, #92478, #7644 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80337 = VERTEX_POINT ( 'NONE', #69022 ) ; +#80338 = VERTEX_POINT ( 'NONE', #12851 ) ; +#80339 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80341 = SURFACE_SIDE_STYLE ('',( #80851 ) ) ; +#80340 = DIRECTION ( 'NONE', ( -0.9686573103133988560, 0.2484009162149200534, 0.000000000000000000 ) ) ; +#80342 = FILL_AREA_STYLE_COLOUR ( '', #69927 ) ; +#80343 = AXIS2_PLACEMENT_3D ( 'NONE', #7098, #15310, #8602 ) ; +#80344 = ORIENTED_EDGE ( 'NONE', *, *, #81834, .T. ) ; +#80345 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80346 = FACE_OUTER_BOUND ( 'NONE', #39761, .T. ) ; +#80347 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 13.09601199999999999, 0.8991599999999999593 ) ) ; +#80348 = ORIENTED_EDGE ( 'NONE', *, *, #98106, .T. ) ; +#80349 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80350 = PLANE ( 'NONE', #28487 ) ; +#80351 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80352 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55939 ), #24967 ) ; +#80353 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#80354 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78710 ), #96633 ) ; +#80355 = ORIENTED_EDGE ( 'NONE', *, *, #83824, .T. ) ; +#80356 = SURFACE_STYLE_FILL_AREA ( #35905 ) ; +#80357 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28161 ) ) ; +#80358 = SURFACE_STYLE_FILL_AREA ( #96132 ) ; +#80359 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80360 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80361 = FILL_AREA_STYLE ('',( #56892 ) ) ; +#80362 = LINE ( 'NONE', #55872, #43502 ) ; +#80363 = AXIS2_PLACEMENT_3D ( 'NONE', #65542, #50282, #19079 ) ; +#80364 = ADVANCED_FACE ( 'NONE', ( #60434, #68025 ), #4753, .T. ) ; +#80366 = FACE_OUTER_BOUND ( 'NONE', #78575, .T. ) ; +#80365 = PLANE ( 'NONE', #41297 ) ; +#80367 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80368 = SURFACE_STYLE_USAGE ( .BOTH. , #43048 ) ; +#80369 = AXIS2_PLACEMENT_3D ( 'NONE', #76902, #13535, #44725 ) ; +#80370 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99757 ) ) ; +#80371 = CARTESIAN_POINT ( 'NONE', ( -0.9858361255783950616, -0.9444486738239200596, 0.8299999999999999600 ) ) ; +#80372 = VERTEX_POINT ( 'NONE', #53249 ) ; +#80373 = FILL_AREA_STYLE_COLOUR ( '', #28391 ) ; +#80374 = VECTOR ( 'NONE', #75200, 1000.000000000000000 ) ; +#80375 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80376 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73742 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25549, #1553, #78629 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80377 = VECTOR ( 'NONE', #38343, 1000.000000000000000 ) ; +#80378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80379 = ORIENTED_EDGE ( 'NONE', *, *, #1041, .F. ) ; +#80380 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80383 = PRESENTATION_STYLE_ASSIGNMENT (( #71189 ) ) ; +#80382 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80381 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80385 = STYLED_ITEM ( 'NONE', ( #38881 ), #59415 ) ; +#80384 = FACE_OUTER_BOUND ( 'NONE', #69026, .T. ) ; +#80386 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62054, 'distance_accuracy_value', 'NONE'); +#80387 = CARTESIAN_POINT ( 'NONE', ( 6.212268750249974936, 10.39365124975002530, 0.8648700000000000276 ) ) ; +#80388 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80389 = CARTESIAN_POINT ( 'NONE', ( 0.3189951478977410271, -1.329088006532930022, 0.8100000000000000533 ) ) ; +#80390 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80391 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80392 = ORIENTED_EDGE ( 'NONE', *, *, #24662, .F. ) ; +#80393 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.598204329022293368, -11.40235793455044089 ) ) ; +#80394 = EDGE_CURVE ( 'NONE', #39991, #53559, #43939, .T. ) ; +#80395 = CARTESIAN_POINT ( 'NONE', ( 0.9685869866146582519, 0.4055590759269661061, 0.8100000000000000533 ) ) ; +#80396 = PLANE ( 'NONE', #14214 ) ; +#80397 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#80398 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95042 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40618, #73276, #65586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80399 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#80400 = FILL_AREA_STYLE_COLOUR ( '', #28921 ) ; +#80401 = EDGE_CURVE ( 'NONE', #35632, #42994, #6202, .T. ) ; +#80402 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#80403 = SURFACE_STYLE_FILL_AREA ( #81427 ) ; +#80404 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.750000000000000222, 0.000000000000000000 ) ) ; +#80405 = CARTESIAN_POINT ( 'NONE', ( 1.089738207395029912, -1.411115659170130154, 0.8299999999999999600 ) ) ; +#80406 = SURFACE_SIDE_STYLE ('',( #18064 ) ) ; +#80407 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496381000000000405, 0.8648700000000000276 ) ) ; +#80408 = ORIENTED_EDGE ( 'NONE', *, *, #94218, .F. ) ; +#80409 = PRESENTATION_STYLE_ASSIGNMENT (( #81434 ) ) ; +#80410 = STYLED_ITEM ( 'NONE', ( #50490 ), #70792 ) ; +#80411 = ORIENTED_EDGE ( 'NONE', *, *, #64956, .F. ) ; +#80412 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2784314575050762519, 0.1458578643762690197 ) ) ; +#80413 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#80414 = CYLINDRICAL_SURFACE ( 'NONE', #55767, 0.4459546481032609644 ) ; +#80415 = AXIS2_PLACEMENT_3D ( 'NONE', #17106, #54041, #100369 ) ; +#80416 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80417 = EDGE_CURVE ( 'NONE', #10112, #73618, #19464, .T. ) ; +#80418 = ORIENTED_EDGE ( 'NONE', *, *, #84470, .T. ) ; +#80419 = FILL_AREA_STYLE ('',( #33969 ) ) ; +#80420 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69540, #38928, #30236 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80422 = SURFACE_STYLE_USAGE ( .BOTH. , #32946 ) ; +#80423 = ORIENTED_EDGE ( 'NONE', *, *, #29295, .T. ) ; +#80424 = FILL_AREA_STYLE_COLOUR ( '', #62508 ) ; +#80425 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82070, #20244, #35111 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80426 = SURFACE_SIDE_STYLE ('',( #42619 ) ) ; +#80427 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80428 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#80429 = AXIS2_PLACEMENT_3D ( 'NONE', #48723, #31863, #79862 ) ; +#80430 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01500000000000001506, -0.1400000000000000411 ) ) ; +#80431 = MANIFOLD_SOLID_BREP ( 'ÊäÈë23', #46784 ) ; +#80432 = VERTEX_POINT ( 'NONE', #47075 ) ; +#80433 = LINE ( 'NONE', #10369, #97806 ) ; +#80434 = EDGE_CURVE ( 'NONE', #96849, #36712, #91037, .T. ) ; +#80435 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46109, 'distance_accuracy_value', 'NONE'); +#80437 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6930 ) ) ; +#80436 = LINE ( 'NONE', #10373, #59888 ) ; +#80438 = VERTEX_POINT ( 'NONE', #38925 ) ; +#80439 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80440 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23364 ), #5387 ) ; +#80441 = VECTOR ( 'NONE', #4503, 1000.000000000000000 ) ; +#80442 = CARTESIAN_POINT ( 'NONE', ( -0.3870380129777519773, 0.4877332074569978859, 0.8100000000000000533 ) ) ; +#80443 = FILL_AREA_STYLE_COLOUR ( '', #3205 ) ; +#80444 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80445 = SURFACE_STYLE_FILL_AREA ( #19126 ) ; +#80446 = CARTESIAN_POINT ( 'NONE', ( -0.7453505133853431941, 1.552609075926966176, 0.8100000000000000533 ) ) ; +#80447 = FILL_AREA_STYLE_COLOUR ( '', #48324 ) ; +#80448 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77136 ), #64118 ) ; +#80449 = VECTOR ( 'NONE', #49527, 1000.000000000000000 ) ; +#80450 = ADVANCED_FACE ( 'NONE', ( #54253 ), #85376, .T. ) ; +#80451 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2169 ) ) ; +#80452 = AXIS2_PLACEMENT_3D ( 'NONE', #38263, #15747, #69353 ) ; +#80453 = ORIENTED_EDGE ( 'NONE', *, *, #10564, .T. ) ; +#80455 = VERTEX_POINT ( 'NONE', #46562 ) ; +#80454 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80456 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15600, 'distance_accuracy_value', 'NONE'); +#80457 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80458 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#80459 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, 0.000000000000000000 ) ) ; +#80460 = ORIENTED_EDGE ( 'NONE', *, *, #71386, .F. ) ; +#80461 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.000000000000000000 ) ) ; +#80462 = FILL_AREA_STYLE_COLOUR ( '', #40920 ) ; +#80463 = SURFACE_SIDE_STYLE ('',( #8901 ) ) ; +#80464 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80465 = ORIENTED_EDGE ( 'NONE', *, *, #4146, .T. ) ; +#80467 = LINE ( 'NONE', #72800, #38853 ) ; +#80466 = SURFACE_SIDE_STYLE ('',( #18127 ) ) ; +#80468 = ORIENTED_EDGE ( 'NONE', *, *, #8726, .T. ) ; +#80469 = ORIENTED_EDGE ( 'NONE', *, *, #40514, .F. ) ; +#80470 = FILL_AREA_STYLE_COLOUR ( '', #70552 ) ; +#80471 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80472 = FILL_AREA_STYLE_COLOUR ( '', #94629 ) ; +#80473 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26696 ) ) ; +#80474 = ORIENTED_EDGE ( 'NONE', *, *, #59922, .F. ) ; +#80475 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80476 = ORIENTED_EDGE ( 'NONE', *, *, #10882, .T. ) ; +#80477 = CARTESIAN_POINT ( 'NONE', ( 1.360598746852770047, -1.365766081162230083, 0.8299999999999999600 ) ) ; +#80478 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95080 ), #23396 ) ; +#80479 = EDGE_LOOP ( 'NONE', ( #47817, #26979, #88526, #87458 ) ) ; +#80480 = SURFACE_STYLE_USAGE ( .BOTH. , #49332 ) ; +#80481 = EDGE_CURVE ( 'NONE', #84331, #96473, #47591, .T. ) ; +#80483 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999999335, 0.8648700000000000276 ) ) ; +#80482 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#80484 = CARTESIAN_POINT ( 'NONE', ( -1.063525042275559995, -1.248384608377719918, 0.8100000000000000533 ) ) ; +#80485 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80486 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62488 ), #18431 ) ; +#80487 = SURFACE_SIDE_STYLE ('',( #25870 ) ) ; +#80489 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16808 ), #73925 ) ; +#80488 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80490 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29377 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4192, #25678, #66471 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80491 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80492 = FILL_AREA_STYLE ('',( #35554 ) ) ; +#80493 = CARTESIAN_POINT ( 'NONE', ( 1.237877634622789991, -0.9585098101514269997, 0.8299999999999999600 ) ) ; +#80494 = ORIENTED_EDGE ( 'NONE', *, *, #57880, .T. ) ; +#80495 = SURFACE_STYLE_USAGE ( .BOTH. , #66163 ) ; +#80496 = CARTESIAN_POINT ( 'NONE', ( 2.079999999999999627, 1.600000000000000089, -11.32000000000000028 ) ) ; +#80497 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29941 ) ) ; +#80499 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999990319, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#80498 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80500 = PRESENTATION_STYLE_ASSIGNMENT (( #25386 ) ) ; +#80501 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26573, 'distance_accuracy_value', 'NONE'); +#80502 = PLANE ( 'NONE', #100490 ) ; +#80503 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36486 ) ) ; +#80504 = VECTOR ( 'NONE', #34466, 1000.000000000000000 ) ; +#80505 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80506 = STYLED_ITEM ( 'NONE', ( #17193 ), #21295 ) ; +#80507 = LINE ( 'NONE', #49353, #79319 ) ; +#80508 = PLANE ( 'NONE', #85203 ) ; +#80509 = ORIENTED_EDGE ( 'NONE', *, *, #90029, .T. ) ; +#80510 = EDGE_CURVE ( 'NONE', #75030, #55353, #85862, .T. ) ; +#80511 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80512 = SURFACE_STYLE_USAGE ( .BOTH. , #49359 ) ; +#80515 = AXIS2_PLACEMENT_3D ( 'NONE', #72311, #41698, #33545 ) ; +#80514 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80513 = SURFACE_STYLE_USAGE ( .BOTH. , #32025 ) ; +#80516 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80517 = STYLED_ITEM ( 'NONE', ( #50886 ), #35277 ) ; +#80518 = SURFACE_SIDE_STYLE ('',( #18176 ) ) ; +#80519 = LINE ( 'NONE', #73362, #36649 ) ; +#80520 = VECTOR ( 'NONE', #47825, 1000.000000000000000 ) ; +#80521 = ADVANCED_FACE ( 'NONE', ( #39411 ), #77721, .F. ) ; +#80522 = CARTESIAN_POINT ( 'NONE', ( 1.566666666666656660, 3.500000000000000000, 0.000000000000000000 ) ) ; +#80523 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80524 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80525 = VECTOR ( 'NONE', #77775, 1000.000000000000000 ) ; +#80526 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80527 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999987121, -3.266666666666653285, 0.000000000000000000 ) ) ; +#80528 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80529 = FILL_AREA_STYLE_COLOUR ( '', #96081 ) ; +#80530 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#80531 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#80532 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #34447, #42587, #81903, #73724 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80533 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55176 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38433, #100574, #63458 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80534 = CARTESIAN_POINT ( 'NONE', ( 1.818850168448489901, -1.194792006717259936, 0.8100000000000004974 ) ) ; +#80535 = LINE ( 'NONE', #96807, #74809 ) ; +#80536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80537 = VECTOR ( 'NONE', #201, 1000.000000000000000 ) ; +#80538 = CARTESIAN_POINT ( 'NONE', ( -0.2066711868101530070, -0.9216047924506359790, 0.8300000000000009592 ) ) ; +#80539 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#80540 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80541 = EDGE_CURVE ( 'NONE', #44962, #19280, #84861, .T. ) ; +#80542 = ORIENTED_EDGE ( 'NONE', *, *, #59515, .F. ) ; +#80543 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80544 = EDGE_CURVE ( 'NONE', #33080, #8279, #88407, .T. ) ; +#80545 = SURFACE_STYLE_USAGE ( .BOTH. , #88199 ) ; +#80546 = AXIS2_PLACEMENT_3D ( 'NONE', #89952, #81824, #5649 ) ; +#80548 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80547 = LINE ( 'NONE', #43715, #91654 ) ; +#80549 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#80550 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49803 ) ) ; +#80551 = SURFACE_STYLE_FILL_AREA ( #25931 ) ; +#80552 = LINE ( 'NONE', #79536, #36994 ) ; +#80553 = VERTEX_POINT ( 'NONE', #25156 ) ; +#80554 = SURFACE_SIDE_STYLE ('',( #9505 ) ) ; +#80555 = AXIS2_PLACEMENT_3D ( 'NONE', #71569, #15382, #15893 ) ; +#80556 = LINE ( 'NONE', #2939, #77391 ) ; +#80557 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, -0.1250000000000000000 ) ) ; +#80558 = EDGE_CURVE ( 'NONE', #36185, #21653, #56799, .T. ) ; +#80559 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4750000000000000333, 0.2458578643762690530 ) ) ; +#80560 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80561 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#80562 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, 0.000000000000000000 ) ) ; +#80563 = EDGE_LOOP ( 'NONE', ( #66327, #12444, #98921, #47658 ) ) ; +#80564 = EDGE_LOOP ( 'NONE', ( #88962, #6743, #52179, #9186 ) ) ; +#80565 = FILL_AREA_STYLE_COLOUR ( '', #73554 ) ; +#80566 = ORIENTED_EDGE ( 'NONE', *, *, #62544, .T. ) ; +#80567 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#80568 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#80569 = STYLED_ITEM ( 'NONE', ( #40993 ), #47796 ) ; +#80570 = EDGE_CURVE ( 'NONE', #10511, #79924, #65945, .T. ) ; +#80571 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #89325 ) ; +#80572 = PLANE ( 'NONE', #80302 ) ; +#80573 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.449999999999999956, 0.000000000000000000 ) ) ; +#80574 = ADVANCED_FACE ( 'NONE', ( #26645 ), #4145, .T. ) ; +#80576 = ORIENTED_EDGE ( 'NONE', *, *, #1914, .F. ) ; +#80575 = ORIENTED_EDGE ( 'NONE', *, *, #26595, .T. ) ; +#80577 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80578 = ORIENTED_EDGE ( 'NONE', *, *, #10702, .F. ) ; +#80579 = ORIENTED_EDGE ( 'NONE', *, *, #85623, .T. ) ; +#80581 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23501 ) ) ; +#80580 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74738, 'distance_accuracy_value', 'NONE'); +#80582 = CARTESIAN_POINT ( 'NONE', ( 1.865911170909900108, -1.438073744133560039, 0.8299999999999999600 ) ) ; +#80583 = ORIENTED_EDGE ( 'NONE', *, *, #29644, .F. ) ; +#80584 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #8170, #76193, #37904, #78224 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80585 = VECTOR ( 'NONE', #77343, 1000.000000000000000 ) ; +#80586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80587 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80588 = STYLED_ITEM ( 'NONE', ( #64130 ), #38207 ) ; +#80589 = AXIS2_PLACEMENT_3D ( 'NONE', #97895, #26516, #12102 ) ; +#80590 = ORIENTED_EDGE ( 'NONE', *, *, #76476, .F. ) ; +#80591 = SURFACE_STYLE_FILL_AREA ( #57119 ) ; +#80592 = VERTEX_POINT ( 'NONE', #96540 ) ; +#80594 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80593 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#80595 = VERTEX_POINT ( 'NONE', #40963 ) ; +#80596 = ORIENTED_EDGE ( 'NONE', *, *, #82125, .F. ) ; +#80597 = STYLED_ITEM ( 'NONE', ( #75162 ), #97542 ) ; +#80598 = ADVANCED_FACE ( 'NONE', ( #73093 ), #89412, .F. ) ; +#80599 = SURFACE_SIDE_STYLE ('',( #49442 ) ) ; +#80600 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80601 = MANIFOLD_SOLID_BREP ( 'ÊäÈë26', #100535 ) ; +#80602 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80604 = VERTEX_POINT ( 'NONE', #58814 ) ; +#80603 = SURFACE_STYLE_FILL_AREA ( #17766 ) ; +#80605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85447 ), #5542 ) ; +#80606 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80607 = ORIENTED_EDGE ( 'NONE', *, *, #52242, .T. ) ; +#80608 = CIRCLE ( 'NONE', #61073, 0.04999999999999969746 ) ; +#80609 = CARTESIAN_POINT ( 'NONE', ( -0.2824976818660340228, -1.013847726018640039, 0.8100000000000000533 ) ) ; +#80610 = SURFACE_STYLE_USAGE ( .BOTH. , #57135 ) ; +#80611 = ORIENTED_EDGE ( 'NONE', *, *, #45610, .F. ) ; +#80612 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#80613 = AXIS2_PLACEMENT_3D ( 'NONE', #6522, #7506, #91846 ) ; +#80614 = CARTESIAN_POINT ( 'NONE', ( 0.05990737478736290339, -1.228633653069070020, 0.8299999999999999600 ) ) ; +#80615 = ORIENTED_EDGE ( 'NONE', *, *, #68373, .T. ) ; +#80616 = VERTEX_POINT ( 'NONE', #35330 ) ; +#80617 = EDGE_CURVE ( 'NONE', #7067, #20920, #59822, .T. ) ; +#80618 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#80619 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80620 = SURFACE_STYLE_USAGE ( .BOTH. , #34171 ) ; +#80621 = EDGE_CURVE ( 'NONE', #23174, #64088, #67905, .T. ) ; +#80622 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80623 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8991599999999999593 ) ) ; +#80624 = LINE ( 'NONE', #4971, #73824 ) ; +#80626 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#80625 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #36299, #62176, #13217, #75583 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80627 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1247, 'distance_accuracy_value', 'NONE'); +#80628 = EDGE_LOOP ( 'NONE', ( #74660, #92742, #55671, #51575 ) ) ; +#80629 = FILL_AREA_STYLE_COLOUR ( '', #98380 ) ; +#80630 = VERTEX_POINT ( 'NONE', #83270 ) ; +#80631 = EDGE_CURVE ( 'NONE', #47739, #48017, #37319, .T. ) ; +#80632 = AXIS2_PLACEMENT_3D ( 'NONE', #1999, #42318, #64281 ) ; +#80633 = LINE ( 'NONE', #2004, #66751 ) ; +#80634 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#80635 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80636 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80637 = FILL_AREA_STYLE_COLOUR ( '', #12709 ) ; +#80638 = AXIS2_PLACEMENT_3D ( 'NONE', #1058, #15329, #46490 ) ; +#80639 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#80640 = PRESENTATION_STYLE_ASSIGNMENT (( #2007 ) ) ; +#80641 = PLANE ( 'NONE', #35258 ) ; +#80642 = LINE ( 'NONE', #2009, #88458 ) ; +#80643 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91089 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91901, #83761, #67413 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80644 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67583 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65407, #44300, #5472 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80645 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#80646 = FILL_AREA_STYLE ('',( #97410 ) ) ; +#80647 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80648 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80649 = AXIS2_PLACEMENT_3D ( 'NONE', #68665, #69140, #28388 ) ; +#80650 = EDGE_CURVE ( 'NONE', #9919, #62491, #4630, .T. ) ; +#80651 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80652 = SURFACE_SIDE_STYLE ('',( #25026 ) ) ; +#80653 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.069338999999999817, 0.8991599999999999593 ) ) ; +#80654 = FILL_AREA_STYLE_COLOUR ( '', #46922 ) ; +#80655 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80656 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41508 ) ) ; +#80657 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28455 ), #56330 ) ; +#80659 = EDGE_LOOP ( 'NONE', ( #85434, #29409, #69207, #90884 ) ) ; +#80658 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24758 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67062, #75724, #53261 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80660 = CARTESIAN_POINT ( 'NONE', ( 1.585937742812469908, -0.9305358755170231033, 0.8299999999999999600 ) ) ; +#80661 = EDGE_CURVE ( 'NONE', #4760, #89241, #12958, .T. ) ; +#80662 = ORIENTED_EDGE ( 'NONE', *, *, #3725, .T. ) ; +#80663 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94174, 'distance_accuracy_value', 'NONE'); +#80664 = SURFACE_STYLE_FILL_AREA ( #69552 ) ; +#80665 = SURFACE_STYLE_FILL_AREA ( #9101 ) ; +#80666 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80667 = ADVANCED_FACE ( 'NONE', ( #83768 ), #20456, .T. ) ; +#80669 = VECTOR ( 'NONE', #48475, 1000.000000000000000 ) ; +#80668 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67569 ) ) ; +#80670 = LINE ( 'NONE', #25536, #37324 ) ; +#80671 = VECTOR ( 'NONE', #17686, 1000.000000000000000 ) ; +#80672 = PRESENTATION_STYLE_ASSIGNMENT (( #71986 ) ) ; +#80674 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#80673 = AXIS2_PLACEMENT_3D ( 'NONE', #51740, #29243, #60419 ) ; +#80675 = VECTOR ( 'NONE', #88173, 1000.000000000000000 ) ; +#80676 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80677 = VERTEX_POINT ( 'NONE', #36800 ) ; +#80678 = EDGE_LOOP ( 'NONE', ( #12525, #85839, #16739, #93842 ) ) ; +#80679 = CYLINDRICAL_SURFACE ( 'NONE', #9570, 0.05000000000000012768 ) ; +#80680 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40620, 'distance_accuracy_value', 'NONE'); +#80681 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 5.373192999999999664, 0.8648700000000000276 ) ) ; +#80682 = CARTESIAN_POINT ( 'NONE', ( -0.6761799387799138916, -3.099999999999989875, 0.000000000000000000 ) ) ; +#80683 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#80684 = LINE ( 'NONE', #3053, #85295 ) ; +#80685 = CARTESIAN_POINT ( 'NONE', ( -0.5298487572449830374, -1.185132602208770036, 0.8100000000000000533 ) ) ; +#80686 = STYLED_ITEM ( 'NONE', ( #44893 ), #12484 ) ; +#80687 = SURFACE_SIDE_STYLE ('',( #87816 ) ) ; +#80688 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80689 = PRESENTATION_STYLE_ASSIGNMENT (( #49532 ) ) ; +#80690 = ORIENTED_EDGE ( 'NONE', *, *, #10573, .F. ) ; +#80691 = ORIENTED_EDGE ( 'NONE', *, *, #83170, .T. ) ; +#80692 = EDGE_CURVE ( 'NONE', #68541, #23282, #60313, .T. ) ; +#80693 = VECTOR ( 'NONE', #50069, 1000.000000000000000 ) ; +#80694 = ORIENTED_EDGE ( 'NONE', *, *, #7317, .F. ) ; +#80695 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80696 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8782 ), #90426 ) ; +#80697 = SURFACE_STYLE_FILL_AREA ( #73017 ) ; +#80698 = FILL_AREA_STYLE ('',( #49549 ) ) ; +#80699 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80700 = DIRECTION ( 'NONE', ( 6.123031769111889989E-17, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80701 = FILL_AREA_STYLE_COLOUR ( '', #45907 ) ; +#80702 = SURFACE_SIDE_STYLE ('',( #56213 ) ) ; +#80703 = ADVANCED_FACE ( 'NONE', ( #51649 ), #82761, .F. ) ; +#80706 = ORIENTED_EDGE ( 'NONE', *, *, #69503, .T. ) ; +#80705 = ORIENTED_EDGE ( 'NONE', *, *, #23695, .F. ) ; +#80704 = AXIS2_PLACEMENT_3D ( 'NONE', #34044, #1371, #17667 ) ; +#80707 = LINE ( 'NONE', #95465, #707 ) ; +#80708 = VERTEX_POINT ( 'NONE', #85752 ) ; +#80709 = VECTOR ( 'NONE', #60689, 1000.000000000000000 ) ; +#80710 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.500000000000000000, 0.000000000000000000 ) ) ; +#80711 = VERTEX_POINT ( 'NONE', #15271 ) ; +#80712 = ORIENTED_EDGE ( 'NONE', *, *, #39331, .T. ) ; +#80713 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8199999999999999512 ) ) ; +#80714 = STYLED_ITEM ( 'NONE', ( #84812 ), #82214 ) ; +#80715 = STYLED_ITEM ( 'NONE', ( #78990 ), #88685 ) ; +#80716 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.000000000000000000 ) ) ; +#80717 = FILL_AREA_STYLE ('',( #42896 ) ) ; +#80718 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80719 = ORIENTED_EDGE ( 'NONE', *, *, #6912, .F. ) ; +#80720 = ORIENTED_EDGE ( 'NONE', *, *, #70545, .T. ) ; +#80721 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49263 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97450, #59735, #90827 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80722 = VECTOR ( 'NONE', #68989, 1000.000000000000000 ) ; +#80723 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -1.899999999999999911, 0.1829999999999540050 ) ) ; +#80724 = ORIENTED_EDGE ( 'NONE', *, *, #20189, .F. ) ; +#80725 = EDGE_CURVE ( 'NONE', #66371, #2421, #45915, .T. ) ; +#80726 = EDGE_LOOP ( 'NONE', ( #7586, #93408, #59622, #63767 ) ) ; +#80727 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80728 = SURFACE_STYLE_USAGE ( .BOTH. , #65899 ) ; +#80729 = CARTESIAN_POINT ( 'NONE', ( 1.736267301452500300, -1.505252428432260148, 0.8099999999999996092 ) ) ; +#80730 = ORIENTED_EDGE ( 'NONE', *, *, #82678, .T. ) ; +#80731 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80732 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#80733 = VERTEX_POINT ( 'NONE', #46434 ) ; +#80734 = ADVANCED_FACE ( 'NONE', ( #16792 ), #490, .T. ) ; +#80735 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#80737 = VECTOR ( 'NONE', #98346, 1000.000000000000000 ) ; +#80736 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80738 = VECTOR ( 'NONE', #68667, 1000.000000000000000 ) ; +#80739 = SURFACE_SIDE_STYLE ('',( #65377 ) ) ; +#80740 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#80741 = ADVANCED_FACE ( 'NONE', ( #70956 ), #46950, .F. ) ; +#80742 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80743 = AXIS2_PLACEMENT_3D ( 'NONE', #40573, #33416, #49231 ) ; +#80744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80745 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#80746 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80747 = EDGE_LOOP ( 'NONE', ( #17706, #27453, #86304 ) ) ; +#80748 = CARTESIAN_POINT ( 'NONE', ( 1.549081571661369949, -1.457888621141530061, 0.8099999999999982769 ) ) ; +#80749 = CARTESIAN_POINT ( 'NONE', ( -1.032372237264020054, -0.9101533448649530289, 0.8300000000000000711 ) ) ; +#80750 = EDGE_LOOP ( 'NONE', ( #69862, #82800, #8088, #33458, #59125, #28650, #40609, #15135 ) ) ; +#80751 = ADVANCED_FACE ( 'NONE', ( #87273 ), #95918, .T. ) ; +#80752 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80753 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80754 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.8333333333333322601, 0.000000000000000000 ) ) ; +#80756 = VECTOR ( 'NONE', #65656, 1000.000000000000000 ) ; +#80755 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.069338999999999817, 0.8648700000000000276 ) ) ; +#80757 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999990841, 0.8199999999999998401, 0.04999999999999997502 ) ) ; +#80759 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#80758 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.6600000000000000311, -0.7999999999999999334 ) ) ; +#80760 = CARTESIAN_POINT ( 'NONE', ( 11.51556949950004949, 7.437945499500052016, 0.8991599999999999593 ) ) ; +#80761 = LINE ( 'NONE', #3637, #66257 ) ; +#80762 = FACE_OUTER_BOUND ( 'NONE', #33991, .T. ) ; +#80763 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, -0.2400000000000000189 ) ) ; +#80764 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#80765 = EDGE_CURVE ( 'NONE', #26002, #77944, #19339, .T. ) ; +#80766 = EDGE_CURVE ( 'NONE', #32909, #45227, #71215, .T. ) ; +#80767 = ORIENTED_EDGE ( 'NONE', *, *, #85778, .F. ) ; +#80768 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80770 = SURFACE_STYLE_USAGE ( .BOTH. , #42942 ) ; +#80769 = FILL_AREA_STYLE ('',( #49625 ) ) ; +#80771 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80772 = MANIFOLD_SOLID_BREP ( 'ÊäÈë163', #38864 ) ; +#80773 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80774 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46459 ), #7267 ) ; +#80775 = EDGE_LOOP ( 'NONE', ( #43966, #44231, #48686, #19229, #29057 ) ) ; +#80776 = FACE_OUTER_BOUND ( 'NONE', #69602, .T. ) ; +#80777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38346 ), #69502 ) ; +#80778 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80779 = SURFACE_STYLE_FILL_AREA ( #74111 ) ; +#80780 = PLANE ( 'NONE', #58063 ) ; +#80781 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.000000000000000000 ) ) ; +#80782 = EDGE_CURVE ( 'NONE', #95260, #13350, #66891, .T. ) ; +#80783 = VECTOR ( 'NONE', #99715, 1000.000000000000000 ) ; +#80784 = LINE ( 'NONE', #81301, #81234 ) ; +#80785 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80786 = SURFACE_SIDE_STYLE ('',( #39949 ) ) ; +#80787 = EDGE_CURVE ( 'NONE', #62535, #22641, #73490, .T. ) ; +#80788 = CARTESIAN_POINT ( 'NONE', ( -1.114703706423270324, -1.444732071753930036, 0.8300000000000001821 ) ) ; +#80789 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #72203, #64547 ), + ( #2768, #50766 ), + ( #10836, #33929 ), + ( #51244, #58438 ), + ( #50271, #33422 ), + ( #95650, #81893 ), + ( #73710, #66056 ), + ( #25757, #18568 ), + ( #56916, #42074 ), + ( #96660, #26767 ), + ( #89039, #81408 ), + ( #97159, #89544 ), + ( #19065, #44060 ), + ( #44548, #74721 ), + ( #59933, #35934 ), + ( #20576, #21582 ), + ( #52750, #51753 ), + ( #83879, #22089 ), + ( #36427, #52260 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06671213312217240399, 0.1318787174909979987, 0.1956920876010850019, 0.2591665434654509825, 0.3214355090977070173, 0.3819902024751150038, 0.4405918594941419797, 0.4988820194811739994, 0.5568214512511839853, 0.6142910636512469713, 0.6729433513772550279, 0.7334980447546629589, 0.7961187704913560426, 0.8606751674120479700, 0.9282127582381529685, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#80790 = FACE_OUTER_BOUND ( 'NONE', #68733, .T. ) ; +#80791 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69866, 'distance_accuracy_value', 'NONE'); +#80792 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#80793 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80794 = ORIENTED_EDGE ( 'NONE', *, *, #17513, .T. ) ; +#80795 = ORIENTED_EDGE ( 'NONE', *, *, #45482, .F. ) ; +#80796 = PRESENTATION_STYLE_ASSIGNMENT (( #33826 ) ) ; +#80797 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4883, 'distance_accuracy_value', 'NONE'); +#80798 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97419, 'distance_accuracy_value', 'NONE'); +#80799 = SURFACE_STYLE_USAGE ( .BOTH. , #34846 ) ; +#80800 = CARTESIAN_POINT ( 'NONE', ( -0.2194392452033120111, -1.042364979248350032, 0.8299999999999999600 ) ) ; +#80801 = FILL_AREA_STYLE ('',( #43472 ) ) ; +#80802 = CARTESIAN_POINT ( 'NONE', ( 0.5454545454545449701, -1.073011363636360294, 0.8100000000000001643 ) ) ; +#80803 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77478 ) ) ; +#80804 = PRESENTATION_STYLE_ASSIGNMENT (( #81807 ) ) ; +#80805 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 9.806753000000000497, 0.8648700000000000276 ) ) ; +#80806 = VERTEX_POINT ( 'NONE', #58192 ) ; +#80807 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 5.705533000000000854, 0.8648700000000000276 ) ) ; +#80808 = LINE ( 'NONE', #10743, #90619 ) ; +#80809 = FILL_AREA_STYLE_COLOUR ( '', #63495 ) ; +#80811 = VECTOR ( 'NONE', #5587, 1000.000000000000000 ) ; +#80810 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#80812 = ORIENTED_EDGE ( 'NONE', *, *, #28841, .T. ) ; +#80813 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80814 = VECTOR ( 'NONE', #62442, 1000.000000000000000 ) ; +#80815 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80816 = ORIENTED_EDGE ( 'NONE', *, *, #62721, .F. ) ; +#80817 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31876 ) ) ; +#80818 = PRESENTATION_STYLE_ASSIGNMENT (( #74146 ) ) ; +#80819 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8752 ), #44890 ) ; +#80820 = CARTESIAN_POINT ( 'NONE', ( 3.233333333333330284, -3.500000000000000000, 0.000000000000000000 ) ) ; +#80821 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80822 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80823 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80824 = EDGE_CURVE ( 'NONE', #14330, #35535, #25027, .T. ) ; +#80825 = VERTEX_POINT ( 'NONE', #81664 ) ; +#80826 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80827 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#80828 = EDGE_LOOP ( 'NONE', ( #51613, #4213, #21127, #88263 ) ) ; +#80829 = STYLED_ITEM ( 'NONE', ( #41266 ), #12831 ) ; +#80830 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#80831 = ADVANCED_FACE ( 'NONE', ( #27534 ), #91783, .T. ) ; +#80832 = SURFACE_STYLE_USAGE ( .BOTH. , #3694 ) ; +#80833 = ORIENTED_EDGE ( 'NONE', *, *, #28184, .T. ) ; +#80834 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80835 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80836 = CARTESIAN_POINT ( 'NONE', ( -0.4564379131545099888, -1.136096770074700002, 0.8100000000000000533 ) ) ; +#80837 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80838 = ORIENTED_EDGE ( 'NONE', *, *, #70038, .F. ) ; +#80840 = ORIENTED_EDGE ( 'NONE', *, *, #68033, .T. ) ; +#80839 = VERTEX_POINT ( 'NONE', #67303 ) ; +#80841 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.299999999999999822, 0.000000000000000000 ) ) ; +#80842 = EDGE_LOOP ( 'NONE', ( #66992, #12383, #45505, #54312 ) ) ; +#80843 = FILL_AREA_STYLE ('',( #98071 ) ) ; +#80844 = ADVANCED_FACE ( 'NONE', ( #13110 ), #75479, .T. ) ; +#80845 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #47469 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #74911 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#80846 = VERTEX_POINT ( 'NONE', #29515 ) ; +#80848 = ORIENTED_EDGE ( 'NONE', *, *, #68714, .T. ) ; +#80847 = FACE_OUTER_BOUND ( 'NONE', #17499, .T. ) ; +#80849 = AXIS2_PLACEMENT_3D ( 'NONE', #706, #93593, #69102 ) ; +#80850 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 2.299999999999999822, 0.000000000000000000 ) ) ; +#80851 = SURFACE_STYLE_FILL_AREA ( #25239 ) ; +#80852 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92241 ) ) ; +#80853 = VERTEX_POINT ( 'NONE', #59712 ) ; +#80854 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80855 = SURFACE_STYLE_USAGE ( .BOTH. , #49720 ) ; +#80856 = ORIENTED_EDGE ( 'NONE', *, *, #39575, .T. ) ; +#80857 = ADVANCED_FACE ( 'NONE', ( #35702 ), #21854, .T. ) ; +#80858 = FACE_OUTER_BOUND ( 'NONE', #78421, .T. ) ; +#80859 = STYLED_ITEM ( 'NONE', ( #71399 ), #82619 ) ; +#80860 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46086 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68544, #7192, #52764 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80862 = LINE ( 'NONE', #89995, #29054 ) ; +#80861 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80863 = VECTOR ( 'NONE', #57468, 1000.000000000000000 ) ; +#80864 = CARTESIAN_POINT ( 'NONE', ( 3.949527249749912095, 4.397385750250087710, 0.8991599999999999593 ) ) ; +#80865 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80867 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#80866 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80868 = SURFACE_STYLE_USAGE ( .BOTH. , #66524 ) ; +#80869 = VECTOR ( 'NONE', #97836, 1000.000000000000000 ) ; +#80870 = PRESENTATION_STYLE_ASSIGNMENT (( #40556 ) ) ; +#80871 = EDGE_CURVE ( 'NONE', #2585, #35481, #99845, .T. ) ; +#80872 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#80873 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53158 ) ) ; +#80874 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80875 = EDGE_CURVE ( 'NONE', #10390, #26121, #29785, .T. ) ; +#80877 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#80876 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#80878 = SURFACE_SIDE_STYLE ('',( #2255 ) ) ; +#80879 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#80880 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79787 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5930, #37152, #74449 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80881 = CIRCLE ( 'NONE', #51595, 0.01000000000000002623 ) ; +#80882 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8648700000000000276 ) ) ; +#80883 = CARTESIAN_POINT ( 'NONE', ( 1.177393120509059976, -0.8847374564574109757, 0.8100000000000000533 ) ) ; +#80884 = VERTEX_POINT ( 'NONE', #84642 ) ; +#80885 = SURFACE_SIDE_STYLE ('',( #91409 ) ) ; +#80886 = VECTOR ( 'NONE', #22565, 1000.000000000000000 ) ; +#80887 = EDGE_CURVE ( 'NONE', #77117, #13392, #89576, .T. ) ; +#80888 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#80889 = EDGE_CURVE ( 'NONE', #7779, #97367, #54532, .T. ) ; +#80890 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80891 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97154 ), #67789 ) ; +#80892 = VERTEX_POINT ( 'NONE', #76980 ) ; +#80893 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80895 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80894 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999999778, 3.123820061220055511, -0.02000000000000000042 ) ) ; +#80896 = CARTESIAN_POINT ( 'NONE', ( 1.566431021886530273, -1.318798174699070236, 0.8099999999999976108 ) ) ; +#80897 = AXIS2_PLACEMENT_3D ( 'NONE', #26973, #10522, #2980 ) ; +#80898 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80899 = EDGE_CURVE ( 'NONE', #58410, #49647, #362, .T. ) ; +#80901 = ADVANCED_FACE ( 'NONE', ( #55034 ), #100342, .F. ) ; +#80900 = CARTESIAN_POINT ( 'NONE', ( 0.3455761866733689791, -1.312343239366150049, 0.8100000000000000533 ) ) ; +#80902 = LINE ( 'NONE', #3270, #77964 ) ; +#80903 = SURFACE_STYLE_USAGE ( .BOTH. , #79370 ) ; +#80904 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#80905 = ORIENTED_EDGE ( 'NONE', *, *, #48396, .T. ) ; +#80906 = FACE_OUTER_BOUND ( 'NONE', #78089, .T. ) ; +#80907 = SURFACE_SIDE_STYLE ('',( #2778 ) ) ; +#80908 = EDGE_CURVE ( 'NONE', #51759, #36117, #89495, .T. ) ; +#80909 = FILL_AREA_STYLE ('',( #42088 ) ) ; +#80910 = LINE ( 'NONE', #11842, #25680 ) ; +#80911 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41238 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38158, #29481, #5443 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80912 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 2.134644999999999904, 0.8991599999999999593 ) ) ; +#80913 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#80914 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80915 = EDGE_CURVE ( 'NONE', #59960, #52295, #7950, .T. ) ; +#80916 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75329, 'distance_accuracy_value', 'NONE'); +#80917 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#80918 = FILL_AREA_STYLE_COLOUR ( '', #7967 ) ; +#80919 = STYLED_ITEM ( 'NONE', ( #92253 ), #30020 ) ; +#80920 = ORIENTED_EDGE ( 'NONE', *, *, #39964, .F. ) ; +#80921 = SURFACE_STYLE_USAGE ( .BOTH. , #49778 ) ; +#80922 = ORIENTED_EDGE ( 'NONE', *, *, #88939, .F. ) ; +#80923 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58469, 'distance_accuracy_value', 'NONE'); +#80925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49228, 'distance_accuracy_value', 'NONE'); +#80926 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#80927 = SURFACE_STYLE_USAGE ( .BOTH. , #34963 ) ; +#80928 = CARTESIAN_POINT ( 'NONE', ( -1.392725932787781007, -1.335111600150418631, 0.8099999999997411493 ) ) ; +#80929 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10688 ), #30275 ) ; +#80930 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100296 ) ) ; +#80931 = CARTESIAN_POINT ( 'NONE', ( 1.874899521751800080, -1.024811280222130083, 0.8299999999999999600 ) ) ; +#80932 = CARTESIAN_POINT ( 'NONE', ( -1.233333333333333393, -3.500000000000000000, 0.000000000000000000 ) ) ; +#80933 = LINE ( 'NONE', #41613, #69990 ) ; +#80934 = PLANE ( 'NONE', #88451 ) ; +#80935 = ORIENTED_EDGE ( 'NONE', *, *, #53331, .F. ) ; +#80936 = STYLED_ITEM ( 'NONE', ( #40345 ), #49781 ) ; +#80937 = VECTOR ( 'NONE', #46547, 1000.000000000000000 ) ; +#80938 = PRESENTATION_STYLE_ASSIGNMENT (( #28778 ) ) ; +#80939 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89224, 'distance_accuracy_value', 'NONE'); +#80940 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85160 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46652, #84460, #77809 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80941 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#80942 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49890 ), #1026 ) ; +#80943 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#80944 = ORIENTED_EDGE ( 'NONE', *, *, #45005, .T. ) ; +#80945 = PLANE ( 'NONE', #73871 ) ; +#80946 = PLANE ( 'NONE', #93980 ) ; +#80947 = AXIS2_PLACEMENT_3D ( 'NONE', #29456, #31465, #46235 ) ; +#80948 = FACE_OUTER_BOUND ( 'NONE', #44583, .T. ) ; +#80949 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#80950 = LINE ( 'NONE', #58489, #87075 ) ; +#80951 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#80952 = ADVANCED_FACE ( 'NONE', ( #8449 ), #39181, .T. ) ; +#80953 = ORIENTED_EDGE ( 'NONE', *, *, #77741, .T. ) ; +#80954 = LINE ( 'NONE', #88571, #15565 ) ; +#80955 = SURFACE_SIDE_STYLE ('',( #65592 ) ) ; +#80956 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45172, 'distance_accuracy_value', 'NONE'); +#80957 = SURFACE_SIDE_STYLE ('',( #6000 ) ) ; +#80958 = EDGE_CURVE ( 'NONE', #69997, #69178, #33042, .T. ) ; +#80959 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8648700000000000276 ) ) ; +#80960 = VERTEX_POINT ( 'NONE', #95796 ) ; +#80961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2660 ), #35339 ) ; +#80962 = CARTESIAN_POINT ( 'NONE', ( -0.4049130131136156607, 0.4151391894935035354, 0.8100000000000000533 ) ) ; +#80963 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#80964 = SURFACE_STYLE_USAGE ( .BOTH. , #65107 ) ; +#80965 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#80966 = CARTESIAN_POINT ( 'NONE', ( -1.367418083824303965, -1.104443832495994648, 0.8099999999999112354 ) ) ; +#80967 = FILL_AREA_STYLE_COLOUR ( '', #14050 ) ; +#80968 = SURFACE_SIDE_STYLE ('',( #90608 ) ) ; +#80969 = VECTOR ( 'NONE', #76284, 1000.000000000000000 ) ; +#80970 = AXIS2_PLACEMENT_3D ( 'NONE', #17640, #89630, #3364 ) ; +#80971 = EDGE_LOOP ( 'NONE', ( #92453, #73023, #100607, #11244 ) ) ; +#80972 = ORIENTED_EDGE ( 'NONE', *, *, #83514, .F. ) ; +#80973 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #17372 ) ) ; +#80974 = LINE ( 'NONE', #2843, #13171 ) ; +#80975 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 9.241066999999999254, 0.8991599999999999593 ) ) ; +#80976 = FACE_OUTER_BOUND ( 'NONE', #39915, .T. ) ; +#80977 = VERTEX_POINT ( 'NONE', #80029 ) ; +#80978 = EDGE_CURVE ( 'NONE', #52091, #97792, #72859, .T. ) ; +#80979 = CARTESIAN_POINT ( 'NONE', ( 1.213600188310800077, -1.515470133326519919, 0.8100000000000000533 ) ) ; +#80980 = FILL_AREA_STYLE ('',( #32983 ) ) ; +#80981 = EDGE_LOOP ( 'NONE', ( #35616, #86806, #18572, #50046 ) ) ; +#80982 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27936 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41943, #56272, #80249 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#80984 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#80983 = PRESENTATION_STYLE_ASSIGNMENT (( #65131 ) ) ; +#80985 = ORIENTED_EDGE ( 'NONE', *, *, #77168, .F. ) ; +#80986 = ORIENTED_EDGE ( 'NONE', *, *, #33382, .T. ) ; +#80987 = FACE_OUTER_BOUND ( 'NONE', #18609, .T. ) ; +#80988 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23917 ) ) ; +#80989 = FACE_OUTER_BOUND ( 'NONE', #73901, .T. ) ; +#80990 = FACE_OUTER_BOUND ( 'NONE', #28575, .T. ) ; +#80991 = ORIENTED_EDGE ( 'NONE', *, *, #18992, .F. ) ; +#80992 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#80993 = VECTOR ( 'NONE', #26258, 1000.000000000000000 ) ; +#80994 = LINE ( 'NONE', #35537, #178 ) ; +#80995 = EDGE_LOOP ( 'NONE', ( #96264, #27712, #48307, #32348 ) ) ; +#80996 = SURFACE_STYLE_USAGE ( .BOTH. , #71810 ) ; +#80997 = ORIENTED_EDGE ( 'NONE', *, *, #43868, .T. ) ; +#80998 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#80999 = PLANE ( 'NONE', #11726 ) ; +#81000 = CARTESIAN_POINT ( 'NONE', ( -1.346516121155820089, -1.141526082476290060, 0.8299999999999999600 ) ) ; +#81001 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81002 = VECTOR ( 'NONE', #65501, 1000.000000000000000 ) ; +#81003 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31501, #84623, #63184, #859, #14627, #24381, #45776, #55527, #86635, #16647, #76962 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000013323, 0.3750000000000019984, 0.5000000000000026645, 0.7500000000000013323, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#81004 = SURFACE_STYLE_USAGE ( .BOTH. , #48360 ) ; +#81005 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81006 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81007 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100967 ) ; +#81008 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81009 = FACE_OUTER_BOUND ( 'NONE', #6549, .T. ) ; +#81010 = CARTESIAN_POINT ( 'NONE', ( 1.209440659729950074, -0.9548508715965590143, 0.8100000000000000533 ) ) ; +#81011 = VECTOR ( 'NONE', #19776, 1000.000000000000000 ) ; +#81012 = ORIENTED_EDGE ( 'NONE', *, *, #23472, .F. ) ; +#81013 = FILL_AREA_STYLE ('',( #19703 ) ) ; +#81014 = SURFACE_STYLE_USAGE ( .BOTH. , #95261 ) ; +#81015 = VECTOR ( 'NONE', #2396, 1000.000000000000000 ) ; +#81016 = PRESENTATION_STYLE_ASSIGNMENT (( #33541 ) ) ; +#81017 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#81018 = SURFACE_STYLE_USAGE ( .BOTH. , #96281 ) ; +#81020 = EDGE_CURVE ( 'NONE', #25590, #32383, #2412, .T. ) ; +#81019 = SURFACE_SIDE_STYLE ('',( #18678 ) ) ; +#81021 = VECTOR ( 'NONE', #89089, 1000.000000000000000 ) ; +#81022 = FILL_AREA_STYLE_COLOUR ( '', #32176 ) ; +#81023 = CARTESIAN_POINT ( 'NONE', ( 6.125000000000000000, 0.000000000000000000, -13.40000000000000036 ) ) ; +#81024 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.399999999999999911, -11.41999999999999993 ) ) ; +#81025 = CLOSED_SHELL ( 'NONE', ( #16936, #89626, #47439, #8434, #52061, #50260 ) ) ; +#81026 = PRESENTATION_STYLE_ASSIGNMENT (( #18683 ) ) ; +#81027 = ORIENTED_EDGE ( 'NONE', *, *, #70606, .F. ) ; +#81028 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81029 = AXIS2_PLACEMENT_3D ( 'NONE', #39670, #48380, #9946 ) ; +#81030 = FACE_OUTER_BOUND ( 'NONE', #10663, .T. ) ; +#81031 = PRESENTATION_STYLE_ASSIGNMENT (( #49885 ) ) ; +#81032 = AXIS2_PLACEMENT_3D ( 'NONE', #68569, #76238, #99144 ) ; +#81033 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#81034 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69449, 'distance_accuracy_value', 'NONE'); +#81035 = FILL_AREA_STYLE ('',( #26399 ) ) ; +#81036 = VECTOR ( 'NONE', #41246, 1000.000000000000000 ) ; +#81037 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#81038 = EDGE_CURVE ( 'NONE', #2547, #8086, #71854, .T. ) ; +#81039 = AXIS2_PLACEMENT_3D ( 'NONE', #12305, #43521, #5184 ) ; +#81040 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#81041 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#81042 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81043 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#81044 = CARTESIAN_POINT ( 'NONE', ( -0.4441558441558439707, -1.079220779220779969, 0.8099999999999619726 ) ) ; +#81045 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81046 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#81047 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81048 = CARTESIAN_POINT ( 'NONE', ( -0.2824976818660340228, -1.013847726018640039, 0.8300000000000009592 ) ) ; +#81049 = FILL_AREA_STYLE_COLOUR ( '', #58544 ) ; +#81050 = ORIENTED_EDGE ( 'NONE', *, *, #17504, .F. ) ; +#81051 = FACE_OUTER_BOUND ( 'NONE', #24474, .T. ) ; +#81052 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#81053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14678, 'distance_accuracy_value', 'NONE'); +#81054 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#81055 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58053, 'distance_accuracy_value', 'NONE'); +#81056 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14138 ) ) ; +#81057 = PLANE ( 'NONE', #42158 ) ; +#81058 = AXIS2_PLACEMENT_3D ( 'NONE', #60183, #91275, #52489 ) ; +#81059 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.123820061220055511, 0.000000000000000000 ) ) ; +#81060 = FILL_AREA_STYLE_COLOUR ( '', #88472 ) ; +#81061 = FACE_OUTER_BOUND ( 'NONE', #56624, .T. ) ; +#81062 = EDGE_CURVE ( 'NONE', #45876, #90091, #32557, .T. ) ; +#81063 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81064 = EDGE_LOOP ( 'NONE', ( #93030, #64998, #69605, #67736 ) ) ; +#81065 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 8.413752999999999815, 0.8991599999999999593 ) ) ; +#81066 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81067 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.009158714663670502E-14 ) ) ; +#81068 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26735, 'distance_accuracy_value', 'NONE'); +#81069 = STYLED_ITEM ( 'NONE', ( #56440 ), #83936 ) ; +#81070 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67872, 'distance_accuracy_value', 'NONE'); +#81071 = ADVANCED_FACE ( 'NONE', ( #1906 ), #87667, .F. ) ; +#81072 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#81073 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #28454 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86019, #46700, #246 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81074 = ORIENTED_EDGE ( 'NONE', *, *, #92288, .T. ) ; +#81075 = VERTEX_POINT ( 'NONE', #34070 ) ; +#81076 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.100000000000000311, -0.02000000000000000042 ) ) ; +#81077 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81078 = ORIENTED_EDGE ( 'NONE', *, *, #60314, .F. ) ; +#81079 = CARTESIAN_POINT ( 'NONE', ( 1.748219681435579931, -1.226312279485590073, 0.8100000000000000533 ) ) ; +#81080 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24010 ), #15789 ) ; +#81081 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 11.02344800000000014, 0.8648700000000000276 ) ) ; +#81082 = FILL_AREA_STYLE ('',( #18743 ) ) ; +#81083 = LINE ( 'NONE', #27444, #4024 ) ; +#81084 = CARTESIAN_POINT ( 'NONE', ( 1.075634261959845794, -1.496445653724932434, 0.8099999999996773115 ) ) ; +#81086 = ORIENTED_EDGE ( 'NONE', *, *, #44644, .F. ) ; +#81085 = ORIENTED_EDGE ( 'NONE', *, *, #76694, .T. ) ; +#81087 = AXIS2_PLACEMENT_3D ( 'NONE', #25084, #76263, #53304 ) ; +#81088 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46876 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91644, #1122, #54785 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81089 = ORIENTED_EDGE ( 'NONE', *, *, #47782, .T. ) ; +#81090 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65983, #2192, #89951 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81091 = CARTESIAN_POINT ( 'NONE', ( 1.901147915587950044, -1.336905478629369926, 0.8299999999999999600 ) ) ; +#81093 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2808578643762690286, -0.1399999999999999856 ) ) ; +#81092 = CARTESIAN_POINT ( 'NONE', ( 0.5377516545130740511, -1.015240267636180027, 0.8100000000000000533 ) ) ; +#81094 = ORIENTED_EDGE ( 'NONE', *, *, #83974, .F. ) ; +#81095 = CLOSED_SHELL ( 'NONE', ( #26976, #14820, #69134, #67039, #21149, #71208 ) ) ; +#81096 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67992 ) ) ; +#81097 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#81098 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74602 ), #56694 ) ; +#81099 = EDGE_LOOP ( 'NONE', ( #87611, #567, #68729, #99739 ) ) ; +#81100 = EDGE_LOOP ( 'NONE', ( #57405, #16220, #26212, #11170 ) ) ; +#81102 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8648700000000000276 ) ) ; +#81101 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#81103 = EDGE_CURVE ( 'NONE', #74262, #23190, #86661, .T. ) ; +#81104 = VERTEX_POINT ( 'NONE', #55551 ) ; +#81105 = VERTEX_POINT ( 'NONE', #79002 ) ; +#81106 = CARTESIAN_POINT ( 'NONE', ( 0.9818181818181811460, -1.059983766233770108, 0.8100000000000000533 ) ) ; +#81107 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81108 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81109 = SURFACE_STYLE_USAGE ( .BOTH. , #64253 ) ; +#81110 = PLANE ( 'NONE', #34334 ) ; +#81112 = ORIENTED_EDGE ( 'NONE', *, *, #46759, .F. ) ; +#81111 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81113 = SURFACE_SIDE_STYLE ('',( #2984 ) ) ; +#81114 = VERTEX_POINT ( 'NONE', #41223 ) ; +#81115 = FACE_OUTER_BOUND ( 'NONE', #20171, .T. ) ; +#81116 = VERTEX_POINT ( 'NONE', #8964 ) ; +#81118 = FILL_AREA_STYLE ('',( #50978 ) ) ; +#81117 = SURFACE_SIDE_STYLE ('',( #96882 ) ) ; +#81119 = PLANE ( 'NONE', #64078 ) ; +#81120 = VERTEX_POINT ( 'NONE', #72338 ) ; +#81121 = ORIENTED_EDGE ( 'NONE', *, *, #51955, .F. ) ; +#81122 = ADVANCED_FACE ( 'NONE', ( #73863 ), #26907, .T. ) ; +#81123 = PRESENTATION_STYLE_ASSIGNMENT (( #57656 ) ) ; +#81124 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81125 = EDGE_CURVE ( 'NONE', #40037, #41413, #67185, .T. ) ; +#81126 = CARTESIAN_POINT ( 'NONE', ( 0.01569390708528280165, 1.386225820966699995, 0.8100000000000000533 ) ) ; +#81127 = FACE_OUTER_BOUND ( 'NONE', #33406, .T. ) ; +#81128 = VECTOR ( 'NONE', #5346, 1000.000000000000000 ) ; +#81129 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#81130 = LINE ( 'NONE', #15120, #99266 ) ; +#81131 = VECTOR ( 'NONE', #35188, 1000.000000000000000 ) ; +#81132 = VERTEX_POINT ( 'NONE', #50417 ) ; +#81133 = VERTEX_POINT ( 'NONE', #12991 ) ; +#81134 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000017125, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#81135 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81136 = SURFACE_STYLE_USAGE ( .BOTH. , #97880 ) ; +#81138 = ADVANCED_FACE ( 'NONE', ( #20218 ), #5367, .T. ) ; +#81137 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#81139 = VECTOR ( 'NONE', #36065, 1000.000000000000000 ) ; +#81140 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#81141 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 9.827965999999999980, 0.8991599999999999593 ) ) ; +#81142 = LINE ( 'NONE', #4012, #81131 ) ; +#81143 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81145 = VERTEX_POINT ( 'NONE', #11979 ) ; +#81144 = VECTOR ( 'NONE', #32920, 1000.000000000000000 ) ; +#81146 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#81147 = LINE ( 'NONE', #28502, #86292 ) ; +#81148 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81149 = FILL_AREA_STYLE_COLOUR ( '', #81958 ) ; +#81150 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#81151 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81152 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81153 = FILL_AREA_STYLE_COLOUR ( '', #43165 ) ; +#81154 = SURFACE_STYLE_FILL_AREA ( #4021 ) ; +#81155 = EDGE_CURVE ( 'NONE', #39098, #48000, #37080, .T. ) ; +#81156 = LINE ( 'NONE', #58190, #14618 ) ; +#81157 = CARTESIAN_POINT ( 'NONE', ( 1.387778780781510079E-17, 0.2799999999751889845, -2.099015404554671279E-18 ) ) ; +#81158 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81159 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81160 = AXIS2_PLACEMENT_3D ( 'NONE', #70431, #22995, #54127 ) ; +#81161 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496380999999999517, 0.8991599999999999593 ) ) ; +#81162 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.2300000000000000100, 0.5799137866959189758 ) ) ; +#81163 = VECTOR ( 'NONE', #48767, 1000.000000000000000 ) ; +#81164 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48224 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47888, #8999, #14682 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81165 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97789, 'distance_accuracy_value', 'NONE'); +#81166 = ORIENTED_EDGE ( 'NONE', *, *, #66726, .T. ) ; +#81167 = CLOSED_SHELL ( 'NONE', ( #22611, #1633, #50041, #79373, #45494, #67781 ) ) ; +#81168 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#81169 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81170 = SURFACE_SIDE_STYLE ('',( #73988 ) ) ; +#81171 = ORIENTED_EDGE ( 'NONE', *, *, #83786, .F. ) ; +#81172 = PRESENTATION_STYLE_ASSIGNMENT (( #82653 ) ) ; +#81173 = SURFACE_SIDE_STYLE ('',( #26534 ) ) ; +#81175 = VECTOR ( 'NONE', #46433, 1000.000000000000000 ) ; +#81174 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#81176 = CARTESIAN_POINT ( 'NONE', ( 1.825861765333669950, -0.9394184040112200096, 0.8299999999999999600 ) ) ; +#81177 = AXIS2_PLACEMENT_3D ( 'NONE', #66837, #68332, #20372 ) ; +#81178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81179 = STYLED_ITEM ( 'NONE', ( #84844 ), #50308 ) ; +#81180 = CARTESIAN_POINT ( 'NONE', ( 1.799693084787389985, -1.050822088410799937, 0.8100000000000006084 ) ) ; +#81181 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72995 ) ) ; +#81182 = EDGE_CURVE ( 'NONE', #74573, #96015, #59152, .T. ) ; +#81183 = ORIENTED_EDGE ( 'NONE', *, *, #30343, .F. ) ; +#81184 = STYLED_ITEM ( 'NONE', ( #25605 ), #49931 ) ; +#81185 = ORIENTED_EDGE ( 'NONE', *, *, #32241, .F. ) ; +#81186 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81187 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81188 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64833 ), #6084 ) ; +#81189 = CARTESIAN_POINT ( 'NONE', ( -0.4406606078163995965, 0.3469450479559613165, 0.8299999999999999600 ) ) ; +#81190 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#81191 = CARTESIAN_POINT ( 'NONE', ( -0.5047968834700360397, -1.178195226781280081, 0.8100000000000000533 ) ) ; +#81192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22395, 'distance_accuracy_value', 'NONE'); +#81193 = FACE_OUTER_BOUND ( 'NONE', #60008, .T. ) ; +#81194 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#81195 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81196 = EDGE_CURVE ( 'NONE', #98788, #25174, #58075, .T. ) ; +#81197 = LINE ( 'NONE', #4056, #38638 ) ; +#81198 = SURFACE_SIDE_STYLE ('',( #18351 ) ) ; +#81199 = ORIENTED_EDGE ( 'NONE', *, *, #30129, .T. ) ; +#81200 = AXIS2_PLACEMENT_3D ( 'NONE', #46479, #77653, #7608 ) ; +#81201 = ORIENTED_EDGE ( 'NONE', *, *, #6790, .F. ) ; +#81202 = VECTOR ( 'NONE', #31380, 999.9999999999998863 ) ; +#81203 = LINE ( 'NONE', #20382, #28485 ) ; +#81204 = CARTESIAN_POINT ( 'NONE', ( -1.077884384038320098, -0.9706035140527139449, 0.8100000000000000533 ) ) ; +#81205 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.700000000000000178, -0.02000000000000000042 ) ) ; +#81206 = DIRECTION ( 'NONE', ( 0.7071067811865514585, -0.7071067811865435759, 0.000000000000000000 ) ) ; +#81208 = ORIENTED_EDGE ( 'NONE', *, *, #24065, .T. ) ; +#81207 = EDGE_LOOP ( 'NONE', ( #49590, #38210, #89989, #9778 ) ) ; +#81209 = FACE_OUTER_BOUND ( 'NONE', #31842, .T. ) ; +#81210 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81211 = ORIENTED_EDGE ( 'NONE', *, *, #60730, .F. ) ; +#81212 = LINE ( 'NONE', #27587, #21583 ) ; +#81213 = VECTOR ( 'NONE', #2928, 1000.000000000000000 ) ; +#81214 = VECTOR ( 'NONE', #63577, 1000.000000000000000 ) ; +#81215 = SURFACE_STYLE_FILL_AREA ( #73028 ) ; +#81216 = EDGE_LOOP ( 'NONE', ( #288, #74689, #33640, #63456 ) ) ; +#81217 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56807 ) ) ; +#81218 = EDGE_LOOP ( 'NONE', ( #90047, #58334, #87449, #96881 ) ) ; +#81219 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81220 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.000000000000000000 ) ) ; +#81221 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81222 = PLANE ( 'NONE', #32429 ) ; +#81223 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84908 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25740, #18026, #80367 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81225 = PLANE ( 'NONE', #54802 ) ; +#81224 = PLANE ( 'NONE', #70991 ) ; +#81226 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81227 = ORIENTED_EDGE ( 'NONE', *, *, #80077, .T. ) ; +#81228 = VERTEX_POINT ( 'NONE', #27921 ) ; +#81229 = EDGE_CURVE ( 'NONE', #52930, #88109, #63569, .T. ) ; +#81230 = ORIENTED_EDGE ( 'NONE', *, *, #90372, .T. ) ; +#81231 = EDGE_CURVE ( 'NONE', #16128, #40310, #54404, .T. ) ; +#81232 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81233 = STYLED_ITEM ( 'NONE', ( #37521 ), #17252 ) ; +#81234 = VECTOR ( 'NONE', #96047, 1000.000000000000000 ) ; +#81235 = VECTOR ( 'NONE', #15153, 1000.000000000000000 ) ; +#81237 = ORIENTED_EDGE ( 'NONE', *, *, #4097, .F. ) ; +#81236 = LINE ( 'NONE', #19923, #99847 ) ; +#81238 = AXIS2_PLACEMENT_3D ( 'NONE', #47098, #95045, #24666 ) ; +#81239 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58212 ), #23942 ) ; +#81240 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81242 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58443 ), #82817 ) ; +#81241 = PRESENTATION_STYLE_ASSIGNMENT (( #97963 ) ) ; +#81243 = VERTEX_POINT ( 'NONE', #38068 ) ; +#81244 = CARTESIAN_POINT ( 'NONE', ( -0.07142958428783030556, -1.223383224893549892, 0.8299999999999999600 ) ) ; +#81245 = VECTOR ( 'NONE', #84589, 1000.000000000000000 ) ; +#81246 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8099999999998640510 ) ) ; +#81247 = ORIENTED_EDGE ( 'NONE', *, *, #90739, .F. ) ; +#81248 = EDGE_CURVE ( 'NONE', #36748, #25543, #62075, .T. ) ; +#81249 = FILL_AREA_STYLE_COLOUR ( '', #71507 ) ; +#81250 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63083 ) ) ; +#81251 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8991599999999999593 ) ) ; +#81252 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12707 ), #74730 ) ; +#81253 = CARTESIAN_POINT ( 'NONE', ( -1.145511482700600103, -1.226800916006800080, 0.8300000000000000711 ) ) ; +#81254 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5133 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13732, #93369, #15254 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81255 = LINE ( 'NONE', #10160, #62375 ) ; +#81256 = VECTOR ( 'NONE', #9486, 1000.000000000000000 ) ; +#81257 = LINE ( 'NONE', #36775, #16155 ) ; +#81259 = SURFACE_SIDE_STYLE ('',( #33775 ) ) ; +#81258 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#81260 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#81261 = STYLED_ITEM ( 'NONE', ( #77434 ), #50035 ) ; +#81262 = ORIENTED_EDGE ( 'NONE', *, *, #10923, .F. ) ; +#81263 = CARTESIAN_POINT ( 'NONE', ( 1.594774167960720135, -1.488490865982160294, 0.8099999999999982769 ) ) ; +#81264 = CARTESIAN_POINT ( 'NONE', ( -1.089947272470209949, -0.8906029366306299488, 0.8300000000000000711 ) ) ; +#81265 = ORIENTED_EDGE ( 'NONE', *, *, #94039, .F. ) ; +#81266 = LINE ( 'NONE', #11189, #38267 ) ; +#81267 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81268 = CARTESIAN_POINT ( 'NONE', ( -0.2819971453420380136, -1.430103682213279992, 0.8299999999999999600 ) ) ; +#81270 = EDGE_CURVE ( 'NONE', #20813, #89321, #38564, .T. ) ; +#81269 = LINE ( 'NONE', #64912, #75889 ) ; +#81271 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81273 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81272 = FACE_OUTER_BOUND ( 'NONE', #81817, .T. ) ; +#81274 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.09999999999999939493, -0.02000000000000000042 ) ) ; +#81275 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81276 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64918 ) ) ; +#81277 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#81278 = EDGE_CURVE ( 'NONE', #47283, #84686, #93142, .T. ) ; +#81279 = CARTESIAN_POINT ( 'NONE', ( 10.94988424974991581, 4.524665249749911133, 0.8991599999999999593 ) ) ; +#81280 = SURFACE_STYLE_FILL_AREA ( #64922 ) ; +#81281 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51886 ) ) ; +#81282 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#81283 = VERTEX_POINT ( 'NONE', #99723 ) ; +#81284 = EDGE_CURVE ( 'NONE', #60542, #35375, #15544, .T. ) ; +#81285 = EDGE_CURVE ( 'NONE', #7897, #44592, #93643, .T. ) ; +#81286 = LINE ( 'NONE', #35825, #57098 ) ; +#81287 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#81288 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7884 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43501, #96604, #12285 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81289 = AXIS2_PLACEMENT_3D ( 'NONE', #91194, #89193, #43217 ) ; +#81290 = ADVANCED_FACE ( 'NONE', ( #53887 ), #31401, .T. ) ; +#81291 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20164, 'distance_accuracy_value', 'NONE'); +#81292 = VERTEX_POINT ( 'NONE', #54918 ) ; +#81293 = FILL_AREA_STYLE_COLOUR ( '', #66906 ) ; +#81294 = PRODUCT_DEFINITION ( 'δ֪', '', #79658, #35089 ) ; +#81295 = STYLED_ITEM ( 'NONE', ( #6834 ), #55683 ) ; +#81296 = LINE ( 'NONE', #65419, #17920 ) ; +#81297 = CARTESIAN_POINT ( 'NONE', ( 1.233333333333330284, 3.500000000000000000, 0.000000000000000000 ) ) ; +#81298 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666647068, 0.09999999999999939493, 3.495651678170021751E-76 ) ) ; +#81299 = SURFACE_SIDE_STYLE ('',( #26656 ) ) ; +#81300 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81301 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 15.15000000000000036, 0.000000000000000000 ) ) ; +#81302 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81303 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78765 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37907, #100071, #54768 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81304 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81305 = CARTESIAN_POINT ( 'NONE', ( 1.993397459621554901, 1.600000000000000089, -11.36999999999999922 ) ) ; +#81306 = CARTESIAN_POINT ( 'NONE', ( -1.074341942140480066, -1.437631519369750199, 0.8300000000000001821 ) ) ; +#81307 = ADVANCED_FACE ( 'NONE', ( #16057 ), #29398, .T. ) ; +#81308 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35532 ), #11067 ) ; +#81309 = ORIENTED_EDGE ( 'NONE', *, *, #53417, .F. ) ; +#81310 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81311 = EDGE_LOOP ( 'NONE', ( #783, #27320, #35397, #85832 ) ) ; +#81312 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81313 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 5.450014000000000358, 0.000000000000000000 ) ) ; +#81314 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60870, 'distance_accuracy_value', 'NONE'); +#81315 = VECTOR ( 'NONE', #28906, 1000.000000000000000 ) ; +#81316 = LINE ( 'NONE', #10738, #4842 ) ; +#81317 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19091 ) ) ; +#81318 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 4.574163000000001311, 0.8648700000000000276 ) ) ; +#81319 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81320 = VECTOR ( 'NONE', #8163, 1000.000000000000114 ) ; +#81321 = ORIENTED_EDGE ( 'NONE', *, *, #93264, .F. ) ; +#81322 = ADVANCED_FACE ( 'NONE', ( #21725 ), #76862, .T. ) ; +#81323 = LINE ( 'NONE', #27191, #85715 ) ; +#81324 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81325 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#81326 = EDGE_LOOP ( 'NONE', ( #93990, #70634, #57133, #19000 ) ) ; +#81327 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#81328 = ORIENTED_EDGE ( 'NONE', *, *, #226, .F. ) ; +#81329 = EDGE_CURVE ( 'NONE', #61697, #87907, #65428, .T. ) ; +#81330 = PRESENTATION_STYLE_ASSIGNMENT (( #42989 ) ) ; +#81331 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#81332 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81333 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81334 = SURFACE_STYLE_USAGE ( .BOTH. , #48668 ) ; +#81335 = FILL_AREA_STYLE ('',( #26192 ) ) ; +#81336 = EDGE_CURVE ( 'NONE', #38776, #10022, #89922, .T. ) ; +#81337 = VERTEX_POINT ( 'NONE', #81305 ) ; +#81338 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81340 = ORIENTED_EDGE ( 'NONE', *, *, #43901, .F. ) ; +#81341 = SURFACE_STYLE_USAGE ( .BOTH. , #3201 ) ; +#81342 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76940, 'distance_accuracy_value', 'NONE'); +#81343 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1909, #95800, #48887, #71342, #87673, #33045, #8970, #79007, #39695, #56051, #41227, #41724, #63711, #88188, #71859, #80534, #86144, #87171, #10452 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.299597628415967726E-05, 2.557231895451440298E-05, 3.788750805376949013E-05, 4.990157931396579873E-05, 6.168835939862321713E-05, 7.339042041303289179E-05, 8.506726143904314778E-05, 9.679134544029608029E-05, 0.0001083985489511122294, 0.0001199962240404204872, 0.0001316243625949385567, 0.0001434803470821177413, 0.0001555440065564461143, 0.0001679948977570176294, 0.0001810874913286514526, 0.0001947211383080996953 ), + .UNSPECIFIED. ) ; +#81344 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81345 = VERTEX_POINT ( 'NONE', #42959 ) ; +#81346 = ORIENTED_EDGE ( 'NONE', *, *, #87115, .T. ) ; +#81347 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, -1.899999999999999689, -0.02000000000000000042 ) ) ; +#81348 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#81349 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81350 = CARTESIAN_POINT ( 'NONE', ( -0.4564379131545099888, -1.136096770074700002, 0.8299999999999999600 ) ) ; +#81351 = SURFACE_STYLE_FILL_AREA ( #57883 ) ; +#81352 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95934 ) ) ; +#81353 = CARTESIAN_POINT ( 'NONE', ( 0.2744150338662970090, -0.9994076953096140414, 0.8100000000000000533 ) ) ; +#81354 = ORIENTED_EDGE ( 'NONE', *, *, #31854, .F. ) ; +#81356 = ORIENTED_EDGE ( 'NONE', *, *, #11999, .T. ) ; +#81355 = EDGE_LOOP ( 'NONE', ( #45139, #100763, #65260, #14715 ) ) ; +#81357 = FILL_AREA_STYLE ('',( #72652 ) ) ; +#81358 = ORIENTED_EDGE ( 'NONE', *, *, #97344, .T. ) ; +#81359 = EDGE_CURVE ( 'NONE', #15529, #60265, #18965, .T. ) ; +#81360 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81361 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81362 = ORIENTED_EDGE ( 'NONE', *, *, #13238, .T. ) ; +#81364 = VERTEX_POINT ( 'NONE', #65958 ) ; +#81363 = PRESENTATION_STYLE_ASSIGNMENT (( #57895 ) ) ; +#81365 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17725 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98160, #50312, #96694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81366 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81367 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#81368 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#81369 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8991599999999999593 ) ) ; +#81370 = ORIENTED_EDGE ( 'NONE', *, *, #53900, .F. ) ; +#81371 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 1.149999999999999911, 0.000000000000000000 ) ) ; +#81372 = SURFACE_STYLE_FILL_AREA ( #98081 ) ; +#81373 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81374 = ORIENTED_EDGE ( 'NONE', *, *, #50382, .T. ) ; +#81375 = AXIS2_PLACEMENT_3D ( 'NONE', #26302, #72745, #95685 ) ; +#81376 = FILL_AREA_STYLE_COLOUR ( '', #88930 ) ; +#81377 = VECTOR ( 'NONE', #22384, 1000.000000000000000 ) ; +#81378 = FILL_AREA_STYLE ('',( #66515 ) ) ; +#81379 = ADVANCED_FACE ( 'NONE', ( #32424 ), #82289, .F. ) ; +#81380 = ADVANCED_FACE ( 'NONE', ( #26663 ), #50160, .T. ) ; +#81381 = CARTESIAN_POINT ( 'NONE', ( 1.813028831487849990, -1.379727385542079965, 0.8100000000000000533 ) ) ; +#81382 = SURFACE_STYLE_USAGE ( .BOTH. , #95626 ) ; +#81383 = SURFACE_STYLE_USAGE ( .BOTH. , #10809 ) ; +#81384 = CYLINDRICAL_SURFACE ( 'NONE', #13149, 0.009999999999999998473 ) ; +#81385 = VECTOR ( 'NONE', #5747, 1000.000000000000000 ) ; +#81386 = STYLED_ITEM ( 'NONE', ( #34428 ), #1326 ) ; +#81387 = FILL_AREA_STYLE_COLOUR ( '', #5983 ) ; +#81388 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81390 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81389 = CARTESIAN_POINT ( 'NONE', ( 0.3661974308942260170, -0.9626035508172909871, 0.8299999999999999600 ) ) ; +#81391 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#81392 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#81393 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.000000000000000000 ) ) ; +#81394 = EDGE_CURVE ( 'NONE', #92247, #258, #7980, .T. ) ; +#81395 = FACE_OUTER_BOUND ( 'NONE', #84547, .T. ) ; +#81396 = CARTESIAN_POINT ( 'NONE', ( 1.117494933574350036, -0.8946064028769500354, 0.8100000000000000533 ) ) ; +#81397 = ORIENTED_EDGE ( 'NONE', *, *, #84541, .T. ) ; +#81398 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#81399 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#81400 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81401 = FILL_AREA_STYLE ('',( #42573 ) ) ; +#81402 = ORIENTED_EDGE ( 'NONE', *, *, #20163, .T. ) ; +#81403 = EDGE_CURVE ( 'NONE', #20794, #100533, #50637, .T. ) ; +#81404 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81405 = EDGE_CURVE ( 'NONE', #99343, #97211, #67435, .T. ) ; +#81407 = SURFACE_STYLE_FILL_AREA ( #73709 ) ; +#81406 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000411 ) ) ; +#81408 = CARTESIAN_POINT ( 'NONE', ( 1.616346165234739951, -0.9925253384799740397, 0.8299999999999999600 ) ) ; +#81409 = CARTESIAN_POINT ( 'NONE', ( -0.1900794716924300021, -1.425091422160009946, 0.8100000000000000533 ) ) ; +#81410 = STYLED_ITEM ( 'NONE', ( #64326 ), #44095 ) ; +#81411 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81412 = FILL_AREA_STYLE_COLOUR ( '', #65682 ) ; +#81413 = FILL_AREA_STYLE_COLOUR ( '', #59321 ) ; +#81414 = EDGE_LOOP ( 'NONE', ( #59387, #13573, #4360, #64154 ) ) ; +#81415 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#81416 = PRESENTATION_STYLE_ASSIGNMENT (( #25766 ) ) ; +#81417 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 3.393295000000000172, 0.8991599999999999593 ) ) ; +#81418 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#81419 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8648700000000000276 ) ) ; +#81420 = LINE ( 'NONE', #80397, #98954 ) ; +#81421 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81422 = VECTOR ( 'NONE', #8904, 1000.000000000000000 ) ; +#81423 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81424 = LINE ( 'NONE', #80912, #76727 ) ; +#81425 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81426 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81427 = FILL_AREA_STYLE ('',( #57430 ) ) ; +#81428 = FILL_AREA_STYLE_COLOUR ( '', #65378 ) ; +#81429 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27632 ) ) ; +#81430 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8199999999999999512 ) ) ; +#81431 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81432 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#81433 = ORIENTED_EDGE ( 'NONE', *, *, #35698, .F. ) ; +#81434 = SURFACE_STYLE_USAGE ( .BOTH. , #94674 ) ; +#81435 = ORIENTED_EDGE ( 'NONE', *, *, #40268, .F. ) ; +#81436 = FACE_OUTER_BOUND ( 'NONE', #81216, .T. ) ; +#81437 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#81438 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2808578643762690841, -0.1499999999999999944 ) ) ; +#81440 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81439 = VECTOR ( 'NONE', #97677, 1000.000000000000114 ) ; +#81441 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81442 = FILL_AREA_STYLE ('',( #64581 ) ) ; +#81443 = LINE ( 'NONE', #65080, #77713 ) ; +#81444 = CARTESIAN_POINT ( 'NONE', ( -0.1213879870129870031, -1.164935064935070042, 0.8199999999999999512 ) ) ; +#81445 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6494 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40215, #80528, #47863 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81446 = FACE_OUTER_BOUND ( 'NONE', #86996, .T. ) ; +#81447 = EDGE_LOOP ( 'NONE', ( #95462, #21051, #52570, #15088 ) ) ; +#81448 = VECTOR ( 'NONE', #21152, 1000.000000000000000 ) ; +#81449 = EDGE_CURVE ( 'NONE', #10670, #54145, #98501, .T. ) ; +#81450 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8648700000000000276 ) ) ; +#81451 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100858 ) ) ; +#81452 = LINE ( 'NONE', #66099, #76451 ) ; +#81453 = ORIENTED_EDGE ( 'NONE', *, *, #57159, .T. ) ; +#81454 = LINE ( 'NONE', #41619, #15132 ) ; +#81455 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81456 = FILL_AREA_STYLE_COLOUR ( '', #62474 ) ; +#81457 = STYLED_ITEM ( 'NONE', ( #9729 ), #63434 ) ; +#81458 = SURFACE_STYLE_USAGE ( .BOTH. , #19115 ) ; +#81459 = CARTESIAN_POINT ( 'NONE', ( -1.147487226257349890, -1.445368494507049961, 0.8299999999999999600 ) ) ; +#81460 = EDGE_CURVE ( 'NONE', #73941, #17994, #98994, .T. ) ; +#81461 = VERTEX_POINT ( 'NONE', #43461 ) ; +#81462 = LINE ( 'NONE', #2821, #80863 ) ; +#81463 = SURFACE_SIDE_STYLE ('',( #50328 ) ) ; +#81464 = AXIS2_PLACEMENT_3D ( 'NONE', #18685, #73356, #19194 ) ; +#81465 = LINE ( 'NONE', #11393, #97983 ) ; +#81466 = EDGE_CURVE ( 'NONE', #99420, #91699, #88038, .T. ) ; +#81467 = CARTESIAN_POINT ( 'NONE', ( 1.872286628785889917, -1.103202958186300098, 0.8099999999999998312 ) ) ; +#81468 = ORIENTED_EDGE ( 'NONE', *, *, #43049, .F. ) ; +#81469 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, -3.099999999999969891, 0.000000000000000000 ) ) ; +#81470 = FILL_AREA_STYLE ('',( #89102 ) ) ; +#81471 = PRESENTATION_STYLE_ASSIGNMENT (( #10378 ) ) ; +#81472 = FILL_AREA_STYLE_COLOUR ( '', #37404 ) ; +#81473 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68367 ), #53730 ) ; +#81474 = FILL_AREA_STYLE ('',( #80967 ) ) ; +#81475 = EDGE_LOOP ( 'NONE', ( #62120, #67825, #45860, #25036 ) ) ; +#81476 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000089, 2.676179938779915002, 0.000000000000000000 ) ) ; +#81477 = EDGE_CURVE ( 'NONE', #75525, #35769, #90937, .T. ) ; +#81479 = EDGE_CURVE ( 'NONE', #84381, #21592, #76606, .T. ) ; +#81478 = AXIS2_PLACEMENT_3D ( 'NONE', #94026, #86422, #61952 ) ; +#81480 = ADVANCED_FACE ( 'NONE', ( #60329 ), #75608, .T. ) ; +#81481 = ORIENTED_EDGE ( 'NONE', *, *, #98830, .T. ) ; +#81482 = EDGE_CURVE ( 'NONE', #27634, #538, #36320, .T. ) ; +#81483 = VERTEX_POINT ( 'NONE', #21983 ) ; +#81484 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99182, 'distance_accuracy_value', 'NONE'); +#81485 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#81486 = FILL_AREA_STYLE ('',( #32976 ) ) ; +#81487 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#81488 = LINE ( 'NONE', #81973, #5881 ) ; +#81489 = LINE ( 'NONE', #19142, #39412 ) ; +#81490 = EDGE_LOOP ( 'NONE', ( #39611, #84834, #90623, #67951 ) ) ; +#81491 = CARTESIAN_POINT ( 'NONE', ( 1.213600188310800077, -1.515470133326519919, 0.8299999999999999600 ) ) ; +#81492 = FACE_OUTER_BOUND ( 'NONE', #60132, .T. ) ; +#81493 = FACE_OUTER_BOUND ( 'NONE', #83457, .T. ) ; +#81494 = EDGE_CURVE ( 'NONE', #20018, #11153, #30128, .T. ) ; +#81495 = LINE ( 'NONE', #66140, #84178 ) ; +#81496 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66689 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87060, #11374, #96199 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81497 = VERTEX_POINT ( 'NONE', #35839 ) ; +#81499 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81498 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81500 = ORIENTED_EDGE ( 'NONE', *, *, #72771, .F. ) ; +#81501 = EDGE_CURVE ( 'NONE', #96362, #38581, #53644, .T. ) ; +#81502 = VECTOR ( 'NONE', #73189, 1000.000000000000000 ) ; +#81504 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#81503 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#81505 = CARTESIAN_POINT ( 'NONE', ( -1.383450513437169516, 1.393372100993099938, 0.8100000000000000533 ) ) ; +#81506 = VERTEX_POINT ( 'NONE', #505 ) ; +#81507 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68397 ) ) ; +#81508 = FACE_OUTER_BOUND ( 'NONE', #19560, .T. ) ; +#81509 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47203 ) ) ; +#81510 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11263 ), #78198 ) ; +#81511 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#81512 = ORIENTED_EDGE ( 'NONE', *, *, #27235, .T. ) ; +#81513 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 9.923448000000000491, 0.8648700000000000276 ) ) ; +#81514 = FILL_AREA_STYLE ('',( #58536 ) ) ; +#81516 = ORIENTED_EDGE ( 'NONE', *, *, #8115, .F. ) ; +#81515 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #29356, #60526, #13979, #91620 ), + ( #89639, #66637, #20169, #12443 ), + ( #51354, #82493, #74816, #43652 ), + ( #4846, #36036, #39521, #85476 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.3333333333333334259, 0.3333333333333334259, 1.000000000000000000), + ( 0.8047378541243649375, 0.2682459513747884050, 0.2682459513747884050, 0.8047378541243649375), + ( 0.8047378541243649375, 0.2682459513747884050, 0.2682459513747884050, 0.8047378541243649375), + ( 1.000000000000000000, 0.3333333333333334259, 0.3333333333333334259, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#81517 = VECTOR ( 'NONE', #60568, 1000.000000000000000 ) ; +#81519 = PRESENTATION_STYLE_ASSIGNMENT (( #44162 ) ) ; +#81518 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81520 = CARTESIAN_POINT ( 'NONE', ( -1.145511482700600103, -1.226800916006800080, 0.8100000000000000533 ) ) ; +#81521 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81522 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81523 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73335 ), #89648 ) ; +#81524 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81525 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81526 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81527 = PLANE ( 'NONE', #66613 ) ; +#81528 = VERTEX_POINT ( 'NONE', #69424 ) ; +#81529 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#81530 = AXIS2_PLACEMENT_3D ( 'NONE', #61788, #32141, #39270 ) ; +#81531 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#81532 = STYLED_ITEM ( 'NONE', ( #61180 ), #1580 ) ; +#81533 = ADVANCED_FACE ( 'NONE', ( #86800 ), #85771, .T. ) ; +#81535 = SURFACE_STYLE_USAGE ( .BOTH. , #58051 ) ; +#81534 = PLANE ( 'NONE', #83248 ) ; +#81536 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000222, -0.02000000000000000042 ) ) ; +#81537 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72628, 'distance_accuracy_value', 'NONE'); +#81538 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81539 = PRESENTATION_STYLE_ASSIGNMENT (( #3399 ) ) ; +#81540 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81541 = EDGE_CURVE ( 'NONE', #18257, #91073, #38328, .T. ) ; +#81542 = SURFACE_SIDE_STYLE ('',( #83008 ) ) ; +#81543 = VERTEX_POINT ( 'NONE', #63350 ) ; +#81544 = LINE ( 'NONE', #36062, #75482 ) ; +#81545 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81546 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.000000000000000000, -0.4500000000000000666 ) ) ; +#81547 = SURFACE_STYLE_USAGE ( .BOTH. , #98744 ) ; +#81548 = FACE_OUTER_BOUND ( 'NONE', #17138, .T. ) ; +#81549 = PLANE ( 'NONE', #38307 ) ; +#81550 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94524 ) ) ; +#81551 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81552 = SURFACE_STYLE_USAGE ( .BOTH. , #80023 ) ; +#81553 = PLANE ( 'NONE', #83772 ) ; +#81554 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#81555 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16295 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79522, #40724, #2416 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81556 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.099999999999999867, -1.195472123049164304E-89 ) ) ; +#81557 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81558 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.000000000000000000 ) ) ; +#81559 = ADVANCED_FACE ( 'NONE', ( #14780 ), #7580, .T. ) ; +#81560 = LINE ( 'NONE', #11475, #35605 ) ; +#81561 = VECTOR ( 'NONE', #17598, 1000.000000000000000 ) ; +#81562 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81563 = CARTESIAN_POINT ( 'NONE', ( 1.739573088979520010, -1.154690592117219916, 0.8299999999999997380 ) ) ; +#81564 = LINE ( 'NONE', #18708, #73203 ) ; +#81565 = VERTEX_POINT ( 'NONE', #4692 ) ; +#81566 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81567 = ADVANCED_FACE ( 'NONE', ( #46969 ), #85102, .F. ) ; +#81568 = FILL_AREA_STYLE_COLOUR ( '', #53495 ) ; +#81569 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81570 = STYLED_ITEM ( 'NONE', ( #76621 ), #33310 ) ; +#81571 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#81572 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81573 = AXIS2_PLACEMENT_3D ( 'NONE', #63278, #86730, #48457 ) ; +#81574 = VECTOR ( 'NONE', #31477, 1000.000000000000000 ) ; +#81575 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8100000000000001643 ) ) ; +#81576 = ORIENTED_EDGE ( 'NONE', *, *, #75417, .T. ) ; +#81577 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81578 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#81579 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81580 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85030 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22496, #83303, #61835 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81581 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4913 ), #3272 ) ; +#81582 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#81583 = ORIENTED_EDGE ( 'NONE', *, *, #72319, .F. ) ; +#81584 = ORIENTED_EDGE ( 'NONE', *, *, #46478, .F. ) ; +#81585 = PLANE ( 'NONE', #17833 ) ; +#81586 = FACE_OUTER_BOUND ( 'NONE', #99912, .T. ) ; +#81587 = EDGE_LOOP ( 'NONE', ( #92817, #83872, #70085, #70098 ) ) ; +#81588 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81589 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853440755, 2.251909075926970427, 0.8100000000000000533 ) ) ; +#81590 = SURFACE_SIDE_STYLE ('',( #99648 ) ) ; +#81592 = ORIENTED_EDGE ( 'NONE', *, *, #54218, .F. ) ; +#81591 = ORIENTED_EDGE ( 'NONE', *, *, #63178, .F. ) ; +#81593 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40839 ) ) ; +#81594 = VERTEX_POINT ( 'NONE', #6908 ) ; +#81595 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79160, #69447, #62854, #45951 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#81596 = VECTOR ( 'NONE', #18573, 1000.000000000000000 ) ; +#81597 = ORIENTED_EDGE ( 'NONE', *, *, #99872, .F. ) ; +#81598 = EDGE_CURVE ( 'NONE', #6289, #91833, #20816, .T. ) ; +#81599 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38979, 'distance_accuracy_value', 'NONE'); +#81601 = FILL_AREA_STYLE ('',( #3475 ) ) ; +#81602 = EDGE_LOOP ( 'NONE', ( #45644, #51965, #24569, #19247 ) ) ; +#81603 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81604 = EDGE_CURVE ( 'NONE', #91487, #94446, #98344, .T. ) ; +#81605 = SURFACE_STYLE_USAGE ( .BOTH. , #65245 ) ; +#81606 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74627 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83652, #47861, #71852 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81607 = ORIENTED_EDGE ( 'NONE', *, *, #497, .F. ) ; +#81609 = LINE ( 'NONE', #50962, #97417 ) ; +#81608 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#81610 = ORIENTED_EDGE ( 'NONE', *, *, #5193, .T. ) ; +#81611 = VERTEX_POINT ( 'NONE', #13076 ) ; +#81612 = VECTOR ( 'NONE', #50423, 1000.000000000000000 ) ; +#81613 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81614 = ADVANCED_FACE ( 'NONE', ( #60164 ), #45758, .T. ) ; +#81616 = SURFACE_SIDE_STYLE ('',( #49969 ) ) ; +#81615 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81618 = EDGE_LOOP ( 'NONE', ( #35260, #60117, #80848, #86483 ) ) ; +#81617 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#81619 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81620 = EDGE_LOOP ( 'NONE', ( #88229, #59278, #6765, #79934 ) ) ; +#81621 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#81622 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81623 = VERTEX_POINT ( 'NONE', #92731 ) ; +#81624 = VERTEX_POINT ( 'NONE', #29958 ) ; +#81625 = ORIENTED_EDGE ( 'NONE', *, *, #64964, .F. ) ; +#81627 = FILL_AREA_STYLE ('',( #67759 ) ) ; +#81626 = CARTESIAN_POINT ( 'NONE', ( 0.5034558050616539937, -0.9558425862917759863, 0.8299999999999992939 ) ) ; +#81628 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81629 = STYLED_ITEM ( 'NONE', ( #68699 ), #33410 ) ; +#81630 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81631 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#81632 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #46409, #16772 ), + ( #14747, #15770 ), + ( #69380, #92849 ), + ( #22973, #23993 ), + ( #45892, #46923 ), + ( #100429, #85230 ), + ( #47446, #30579 ), + ( #70407, #55141 ), + ( #16261, #15248 ), + ( #24508, #86758 ), + ( #77580, #47954 ), + ( #79111, #7539 ), + ( #3514, #88771 ), + ( #96900, #3002 ), + ( #65801, #72426 ), + ( #41815, #25005 ), + ( #48481, #72948 ), + ( #9566, #17295 ), + ( #18802, #88276 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06674147653962790583, 0.1313279039795479941, 0.1945731643876359995, 0.2562720192966850274, 0.3168036091747580274, 0.3769001200933310147, 0.4368671125188500204, 0.4970767235714639853, 0.5566860891065530392, 0.6162465209635089591, 0.6759633994470309881, 0.7368503919440659855, 0.7988039095700789627, 0.8627460748057349527, 0.9299837341856730388, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#81633 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81634 = PLANE ( 'NONE', #14312 ) ; +#81635 = STYLED_ITEM ( 'NONE', ( #84089 ), #93407 ) ; +#81636 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37823, 'distance_accuracy_value', 'NONE'); +#81637 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81638 = VERTEX_POINT ( 'NONE', #61658 ) ; +#81639 = ORIENTED_EDGE ( 'NONE', *, *, #20139, .T. ) ; +#81640 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#81642 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#81641 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81643 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81644 = AXIS2_PLACEMENT_3D ( 'NONE', #59802, #65921, #52614 ) ; +#81645 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#81646 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 1.050000000000000044 ) ) ; +#81647 = PLANE ( 'NONE', #22345 ) ; +#81648 = ADVANCED_FACE ( 'NONE', ( #14613 ), #61850, .T. ) ; +#81649 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, 3.099999999999992539, -0.02000000000000000042 ) ) ; +#81650 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -7.594371560187039807E-15, 0.000000000000000000 ) ) ; +#81651 = ORIENTED_EDGE ( 'NONE', *, *, #90240, .F. ) ; +#81652 = VECTOR ( 'NONE', #32480, 1000.000000000000000 ) ; +#81653 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81654 = SURFACE_STYLE_FILL_AREA ( #66311 ) ; +#81655 = CARTESIAN_POINT ( 'NONE', ( 0.2440989101500280201, -0.9342297348062970075, 0.8299999999999999600 ) ) ; +#81656 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81657 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81658 = LINE ( 'NONE', #11591, #94630 ) ; +#81659 = FILL_AREA_STYLE_COLOUR ( '', #5745 ) ; +#81660 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81661 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31515, 'distance_accuracy_value', 'NONE'); +#81662 = SURFACE_STYLE_FILL_AREA ( #65819 ) ; +#81663 = VECTOR ( 'NONE', #67644, 1000.000000000000000 ) ; +#81664 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#81665 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31121 ), #3368 ) ; +#81666 = PRESENTATION_STYLE_ASSIGNMENT (( #3541 ) ) ; +#81667 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24614 ) ) ; +#81668 = PRESENTATION_STYLE_ASSIGNMENT (( #82647 ) ) ; +#81669 = EDGE_LOOP ( 'NONE', ( #54086, #92936, #97997, #25176, #79193, #71804 ) ) ; +#81670 = SURFACE_STYLE_FILL_AREA ( #25034 ) ; +#81671 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11343, #73718, #96169, #74227 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#81672 = PLANE ( 'NONE', #63836 ) ; +#81673 = VERTEX_POINT ( 'NONE', #7610 ) ; +#81674 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999223, 0.2399999999999999911 ) ) ; +#81675 = FILL_AREA_STYLE_COLOUR ( '', #4569 ) ; +#81676 = EDGE_CURVE ( 'NONE', #56597, #50880, #12537, .T. ) ; +#81677 = PRESENTATION_STYLE_ASSIGNMENT (( #73992 ) ) ; +#81678 = SURFACE_STYLE_USAGE ( .BOTH. , #97912 ) ; +#81679 = AXIS2_PLACEMENT_3D ( 'NONE', #89060, #50786, #3785 ) ; +#81680 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#81681 = EDGE_CURVE ( 'NONE', #64967, #73740, #23661, .T. ) ; +#81682 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.32000000000000028 ) ) ; +#81683 = ORIENTED_EDGE ( 'NONE', *, *, #48745, .F. ) ; +#81684 = ORIENTED_EDGE ( 'NONE', *, *, #53035, .T. ) ; +#81685 = STYLED_ITEM ( 'NONE', ( #91948 ), #44993 ) ; +#81686 = LINE ( 'NONE', #11617, #46712 ) ; +#81687 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81688 = LINE ( 'NONE', #41365, #80449 ) ; +#81689 = FILL_AREA_STYLE_COLOUR ( '', #38420 ) ; +#81690 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8648700000000000276 ) ) ; +#81691 = FACE_OUTER_BOUND ( 'NONE', #8151, .T. ) ; +#81692 = EDGE_CURVE ( 'NONE', #29795, #27451, #23044, .T. ) ; +#81693 = ORIENTED_EDGE ( 'NONE', *, *, #17123, .T. ) ; +#81694 = VECTOR ( 'NONE', #2374, 1000.000000000000114 ) ; +#81695 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81696 = PLANE ( 'NONE', #87893 ) ; +#81697 = EDGE_LOOP ( 'NONE', ( #38225, #29219, #51867, #75061 ) ) ; +#81698 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81699 = FACE_OUTER_BOUND ( 'NONE', #87939, .T. ) ; +#81700 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220035527, -2.100000000000000089, 0.000000000000000000 ) ) ; +#81701 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#81702 = PRESENTATION_STYLE_ASSIGNMENT (( #35745 ) ) ; +#81703 = AXIS2_PLACEMENT_3D ( 'NONE', #92120, #46135, #52838 ) ; +#81704 = AXIS2_PLACEMENT_3D ( 'NONE', #33516, #50369, #88615 ) ; +#81705 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55684 ) ) ; +#81706 = CARTESIAN_POINT ( 'NONE', ( -0.5276249439448480461, -0.9003793229264169806, 0.8299999999999999600 ) ) ; +#81707 = CARTESIAN_POINT ( 'NONE', ( -0.1168882356512790099, 0.9494653422139083254, 0.8100000000000003864 ) ) ; +#81709 = VERTEX_POINT ( 'NONE', #84795 ) ; +#81708 = EDGE_LOOP ( 'NONE', ( #59343, #38167, #97506, #82422 ) ) ; +#81711 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81710 = AXIS2_PLACEMENT_3D ( 'NONE', #71046, #10164, #96012 ) ; +#81712 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13089 ) ) ; +#81713 = ORIENTED_EDGE ( 'NONE', *, *, #69319, .F. ) ; +#81714 = ADVANCED_FACE ( 'NONE', ( #16333 ), #94464, .T. ) ; +#81715 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.100000000000000089, 0.000000000000000000 ) ) ; +#81716 = VECTOR ( 'NONE', #98715, 1000.000000000000000 ) ; +#81718 = FACE_OUTER_BOUND ( 'NONE', #65365, .T. ) ; +#81717 = FILL_AREA_STYLE ('',( #3589 ) ) ; +#81719 = VERTEX_POINT ( 'NONE', #6628 ) ; +#81720 = ORIENTED_EDGE ( 'NONE', *, *, #4872, .F. ) ; +#81721 = VECTOR ( 'NONE', #21660, 1000.000000000000000 ) ; +#81722 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81723 = PRESENTATION_STYLE_ASSIGNMENT (( #51596 ) ) ; +#81725 = LINE ( 'NONE', #74556, #40134 ) ; +#81724 = SURFACE_STYLE_FILL_AREA ( #25585 ) ; +#81726 = VECTOR ( 'NONE', #21106, 1000.000000000000000 ) ; +#81727 = EDGE_LOOP ( 'NONE', ( #20462, #54601, #40913, #99513 ) ) ; +#81728 = EDGE_LOOP ( 'NONE', ( #40540, #3194, #3629, #77928 ) ) ; +#81729 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#81730 = ORIENTED_EDGE ( 'NONE', *, *, #20107, .T. ) ; +#81731 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81732 = LINE ( 'NONE', #42904, #21574 ) ; +#81733 = EDGE_CURVE ( 'NONE', #66411, #66668, #47510, .T. ) ; +#81734 = VECTOR ( 'NONE', #53247, 1000.000000000000000 ) ; +#81735 = STYLED_ITEM ( 'NONE', ( #88219 ), #2466 ) ; +#81736 = AXIS2_PLACEMENT_3D ( 'NONE', #42422, #80727, #63889 ) ; +#81738 = VERTEX_POINT ( 'NONE', #37848 ) ; +#81737 = SURFACE_STYLE_FILL_AREA ( #44380 ) ; +#81739 = LINE ( 'NONE', #74053, #33505 ) ; +#81740 = SURFACE_STYLE_FILL_AREA ( #59789 ) ; +#81741 = EDGE_LOOP ( 'NONE', ( #63649, #29708, #35604, #7984, #90872, #76967, #79912, #64223, #38235, #25685, #12918 ) ) ; +#81742 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81743 = VERTEX_POINT ( 'NONE', #39859 ) ; +#81744 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #27731 ), #68637 ) ; +#81745 = SURFACE_SIDE_STYLE ('',( #44389 ) ) ; +#81746 = ORIENTED_EDGE ( 'NONE', *, *, #82499, .T. ) ; +#81747 = PRESENTATION_STYLE_ASSIGNMENT (( #96503 ) ) ; +#81748 = CARTESIAN_POINT ( 'NONE', ( 0.3165168699472699632, -0.9635899080461344246, 0.8100000000000002753 ) ) ; +#81749 = SURFACE_STYLE_USAGE ( .BOTH. , #61150 ) ; +#81750 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89875 ), #1849 ) ; +#81751 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#81752 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81753 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11523 ) ) ; +#81754 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81756 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81755 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.266666666666667052, 0.000000000000000000 ) ) ; +#81757 = ADVANCED_FACE ( 'NONE', ( #71001 ), #15323, .F. ) ; +#81758 = LINE ( 'NONE', #27127, #1883 ) ; +#81759 = VERTEX_POINT ( 'NONE', #17363 ) ; +#81760 = SURFACE_STYLE_FILL_AREA ( #89884 ) ; +#81761 = SURFACE_STYLE_USAGE ( .BOTH. , #64406 ) ; +#81762 = ORIENTED_EDGE ( 'NONE', *, *, #56826, .F. ) ; +#81763 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81764 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, -1.149999999999999911 ) ) ; +#81765 = CARTESIAN_POINT ( 'NONE', ( -0.4883433428992630665, -1.252526457973309970, 0.8300000000000000711 ) ) ; +#81767 = FILL_AREA_STYLE_COLOUR ( '', #73652 ) ; +#81766 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -1.100000000000000089 ) ) ; +#81768 = SURFACE_STYLE_FILL_AREA ( #97991 ) ; +#81769 = EDGE_CURVE ( 'NONE', #10054, #21063, #26568, .T. ) ; +#81770 = VECTOR ( 'NONE', #3744, 1000.000000000000114 ) ; +#81771 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81772 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81773 = SURFACE_SIDE_STYLE ('',( #35322 ) ) ; +#81774 = ORIENTED_EDGE ( 'NONE', *, *, #93706, .F. ) ; +#81775 = VECTOR ( 'NONE', #46578, 1000.000000000000000 ) ; +#81776 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701300244, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#81778 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#81777 = SURFACE_SIDE_STYLE ('',( #70685 ) ) ; +#81779 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81780 = VECTOR ( 'NONE', #86238, 999.9999999999998863 ) ; +#81781 = CARTESIAN_POINT ( 'NONE', ( 5.519303999999999988, 2.827608999999999817, 0.8991599999999999593 ) ) ; +#81782 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#81783 = ORIENTED_EDGE ( 'NONE', *, *, #40313, .F. ) ; +#81784 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95279 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18526, #40531, #9782 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81785 = FILL_AREA_STYLE_COLOUR ( '', #31599 ) ; +#81786 = LINE ( 'NONE', #34326, #54009 ) ; +#81787 = FILL_AREA_STYLE_COLOUR ( '', #25401 ) ; +#81788 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.123820061220055511, 0.000000000000000000 ) ) ; +#81789 = LINE ( 'NONE', #72587, #56751 ) ; +#81790 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81791 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81792 = SURFACE_STYLE_USAGE ( .BOTH. , #12750 ) ; +#81793 = PRESENTATION_STYLE_ASSIGNMENT (( #87047 ) ) ; +#81794 = ADVANCED_FACE ( 'NONE', ( #50073 ), #25080, .T. ) ; +#81795 = EDGE_CURVE ( 'NONE', #20515, #37668, #58243, .T. ) ; +#81796 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#81797 = STYLED_ITEM ( 'NONE', ( #16093 ), #2628 ) ; +#81798 = VERTEX_POINT ( 'NONE', #49051 ) ; +#81799 = ORIENTED_EDGE ( 'NONE', *, *, #44296, .T. ) ; +#81801 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29513, 'distance_accuracy_value', 'NONE'); +#81800 = AXIS2_PLACEMENT_3D ( 'NONE', #3349, #18637, #74300 ) ; +#81802 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6369, 'distance_accuracy_value', 'NONE'); +#81803 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81804 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81805 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81806 = SURFACE_SIDE_STYLE ('',( #88949 ) ) ; +#81807 = SURFACE_STYLE_USAGE ( .BOTH. , #27186 ) ; +#81808 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81809 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#81810 = PLANE ( 'NONE', #67299 ) ; +#81811 = STYLED_ITEM ( 'NONE', ( #16074 ), #52433 ) ; +#81812 = ORIENTED_EDGE ( 'NONE', *, *, #72654, .F. ) ; +#81813 = EDGE_CURVE ( 'NONE', #27194, #69464, #18871, .T. ) ; +#81814 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#81815 = PRESENTATION_STYLE_ASSIGNMENT (( #57331 ) ) ; +#81816 = ADVANCED_FACE ( 'NONE', ( #96465 ), #12241, .F. ) ; +#81817 = EDGE_LOOP ( 'NONE', ( #49207, #12563, #58970 ) ) ; +#81818 = CIRCLE ( 'NONE', #16518, 0.5799999999999999600 ) ; +#81819 = SURFACE_STYLE_USAGE ( .BOTH. , #35858 ) ; +#81820 = ORIENTED_EDGE ( 'NONE', *, *, #57012, .F. ) ; +#81821 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #51544, #5491, #36701, #98877 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#81822 = STYLED_ITEM ( 'NONE', ( #71659 ), #46488 ) ; +#81823 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, -3.099999999999969891, 0.000000000000000000 ) ) ; +#81824 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#81825 = SURFACE_STYLE_USAGE ( .BOTH. , #20509 ) ; +#81826 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81827 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.699999999999999734, -0.02000000000000000042 ) ) ; +#81828 = SURFACE_SIDE_STYLE ('',( #3686 ) ) ; +#81829 = ORIENTED_EDGE ( 'NONE', *, *, #49719, .F. ) ; +#81830 = STYLED_ITEM ( 'NONE', ( #85430 ), #45665 ) ; +#81831 = SURFACE_SIDE_STYLE ('',( #51690 ) ) ; +#81832 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81833 = ORIENTED_EDGE ( 'NONE', *, *, #98996, .T. ) ; +#81834 = EDGE_CURVE ( 'NONE', #77506, #55363, #39366, .T. ) ; +#81835 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#81836 = ORIENTED_EDGE ( 'NONE', *, *, #27676, .F. ) ; +#81837 = VERTEX_POINT ( 'NONE', #59758 ) ; +#81838 = EDGE_CURVE ( 'NONE', #25343, #31593, #35750, .T. ) ; +#81839 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.98066299999999984, 0.8991599999999999593 ) ) ; +#81840 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11608 ), #62295 ) ; +#81841 = VECTOR ( 'NONE', #54583, 1000.000000000000000 ) ; +#81842 = CARTESIAN_POINT ( 'NONE', ( -0.4444287376170629744, -1.091919226080539929, 0.8100000000000000533 ) ) ; +#81843 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#81845 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81844 = FILL_AREA_STYLE_COLOUR ( '', #88855 ) ; +#81846 = ORIENTED_EDGE ( 'NONE', *, *, #52722, .F. ) ; +#81848 = ORIENTED_EDGE ( 'NONE', *, *, #32807, .F. ) ; +#81847 = ORIENTED_EDGE ( 'NONE', *, *, #50614, .F. ) ; +#81849 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81850 = ORIENTED_EDGE ( 'NONE', *, *, #82158, .T. ) ; +#81851 = EDGE_CURVE ( 'NONE', #61755, #6399, #28080, .T. ) ; +#81852 = STYLED_ITEM ( 'NONE', ( #46041 ), #95707 ) ; +#81853 = EDGE_CURVE ( 'NONE', #100419, #64228, #90338, .T. ) ; +#81854 = EDGE_LOOP ( 'NONE', ( #94960, #87699, #9526, #72153 ) ) ; +#81855 = ORIENTED_EDGE ( 'NONE', *, *, #57734, .T. ) ; +#81856 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18114, #25838, #42161 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81857 = ORIENTED_EDGE ( 'NONE', *, *, #96878, .F. ) ; +#81858 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.19999999999999929, 0.000000000000000000 ) ) ; +#81859 = PRESENTATION_STYLE_ASSIGNMENT (( #65496 ) ) ; +#81860 = SURFACE_STYLE_FILL_AREA ( #18533 ) ; +#81861 = EDGE_LOOP ( 'NONE', ( #49406, #6476, #65130, #39125 ) ) ; +#81862 = PRESENTATION_STYLE_ASSIGNMENT (( #43029 ) ) ; +#81863 = CARTESIAN_POINT ( 'NONE', ( 9.691233999999999682, 3.266015000000000335, 0.8648700000000000276 ) ) ; +#81864 = AXIS2_PLACEMENT_3D ( 'NONE', #44325, #91801, #31038 ) ; +#81865 = SURFACE_SIDE_STYLE ('',( #12315 ) ) ; +#81866 = CARTESIAN_POINT ( 'NONE', ( 6.367831999999999937, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#81867 = CARTESIAN_POINT ( 'NONE', ( 1.784639205958740149, -1.415447185383410078, 0.8100000000000000533 ) ) ; +#81869 = LINE ( 'NONE', #65024, #72861 ) ; +#81868 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980105, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#81870 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81871 = ADVANCED_FACE ( 'NONE', ( #7496 ), #93805, .T. ) ; +#81872 = CARTESIAN_POINT ( 'NONE', ( -0.2233912930005581554, -1.056062513359939059, 0.8100000000001623679 ) ) ; +#81873 = VERTEX_POINT ( 'NONE', #62238 ) ; +#81874 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63468 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34396, #56880, #96625 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81875 = FILL_AREA_STYLE ('',( #43042 ) ) ; +#81876 = SURFACE_SIDE_STYLE ('',( #74197 ) ) ; +#81877 = CARTESIAN_POINT ( 'NONE', ( 1.075908802260020058, -1.102553831183370026, 0.8300000000000022915 ) ) ; +#81878 = STYLED_ITEM ( 'NONE', ( #69050 ), #52632 ) ; +#81879 = LINE ( 'NONE', #10817, #21726 ) ; +#81880 = ADVANCED_FACE ( 'NONE', ( #63255 ), #100384, .T. ) ; +#81881 = SURFACE_SIDE_STYLE ('',( #19568 ) ) ; +#81882 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#81884 = EDGE_CURVE ( 'NONE', #80080, #10584, #55088, .T. ) ; +#81883 = CARTESIAN_POINT ( 'NONE', ( 0.9913778824254210198, -0.9987792914302020542, 0.8299999999999999600 ) ) ; +#81885 = ORIENTED_EDGE ( 'NONE', *, *, #68108, .T. ) ; +#81886 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.000000000000000000 ) ) ; +#81887 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81888 = CYLINDRICAL_SURFACE ( 'NONE', #28770, 0.02999999999999997113 ) ; +#81889 = ORIENTED_EDGE ( 'NONE', *, *, #11456, .T. ) ; +#81890 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67012, #98088, #75197, #98566, #97130, #11794, #5188, #52232, #20044, #27242, #28231, #27746, #59408, #28711, #50238, #58903, #59905 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.949852962657727017E-05, 3.790559434717988101E-05, 5.547745936300596439E-05, 7.229606869555597144E-05, 8.864561640923084376E-05, 0.0001047639000303240454, 0.0001207051211995097150, 0.0001366123927346739504, 0.0001524984089053124040, 0.0001682691510884706441, 0.0001844097798454603595, 0.0002006394814999836438, 0.0002333902025815907575, 0.0002665283847803948634 ), + .UNSPECIFIED. ) ; +#81891 = EDGE_CURVE ( 'NONE', #27738, #9919, #78528, .T. ) ; +#81892 = SURFACE_STYLE_USAGE ( .BOTH. , #35932 ) ; +#81893 = CARTESIAN_POINT ( 'NONE', ( 1.588352962588889916, -1.042364979248350032, 0.8299999999999999600 ) ) ; +#81894 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83556 ), #73711 ) ; +#81895 = CARTESIAN_POINT ( 'NONE', ( -0.2079889469064460095, -1.408946430034399899, 0.8299999999999999600 ) ) ; +#81896 = FILL_AREA_STYLE_COLOUR ( '', #2379 ) ; +#81897 = SURFACE_STYLE_USAGE ( .BOTH. , #6206 ) ; +#81898 = PLANE ( 'NONE', #41285 ) ; +#81899 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#81900 = VERTEX_POINT ( 'NONE', #39737 ) ; +#81901 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#81902 = PLANE ( 'NONE', #23700 ) ; +#81903 = CARTESIAN_POINT ( 'NONE', ( 2.583333333333333481, 3.099999999999960121, 0.000000000000000000 ) ) ; +#81904 = STYLED_ITEM ( 'NONE', ( #78791 ), #34525 ) ; +#81905 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#81906 = FILL_AREA_STYLE_COLOUR ( '', #49766 ) ; +#81907 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81908 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81909 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8648700000000000276 ) ) ; +#81910 = SURFACE_STYLE_FILL_AREA ( #89557 ) ; +#81911 = EDGE_CURVE ( 'NONE', #81105, #63778, #77517, .T. ) ; +#81912 = EDGE_CURVE ( 'NONE', #84446, #83136, #6510, .T. ) ; +#81914 = VECTOR ( 'NONE', #69931, 1000.000000000000000 ) ; +#81913 = PRESENTATION_STYLE_ASSIGNMENT (( #67547 ) ) ; +#81915 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50783, 'distance_accuracy_value', 'NONE'); +#81916 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60701 ) ) ; +#81917 = SURFACE_SIDE_STYLE ('',( #89560 ) ) ; +#81918 = FACE_OUTER_BOUND ( 'NONE', #1054, .T. ) ; +#81919 = EDGE_LOOP ( 'NONE', ( #83350, #25701 ) ) ; +#81920 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#81922 = ORIENTED_EDGE ( 'NONE', *, *, #88230, .F. ) ; +#81921 = VECTOR ( 'NONE', #22160, 999.9999999999998863 ) ; +#81923 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#81924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72359, 'distance_accuracy_value', 'NONE'); +#81925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63576, 'distance_accuracy_value', 'NONE'); +#81926 = PRESENTATION_STYLE_ASSIGNMENT (( #97194 ) ) ; +#81927 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#81928 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#81929 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.000000000000000000, -1.149999999999999911 ) ) ; +#81930 = AXIS2_PLACEMENT_3D ( 'NONE', #78317, #71665, #65009 ) ; +#81931 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#81932 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.123820061220045297, 0.000000000000000000 ) ) ; +#81933 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81934 = ORIENTED_EDGE ( 'NONE', *, *, #5769, .F. ) ; +#81935 = STYLED_ITEM ( 'NONE', ( #15763 ), #7913 ) ; +#81936 = EDGE_CURVE ( 'NONE', #100232, #27604, #90559, .T. ) ; +#81937 = SURFACE_SIDE_STYLE ('',( #58972 ) ) ; +#81938 = CYLINDRICAL_SURFACE ( 'NONE', #37323, 0.05000000000000012768 ) ; +#81939 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38538, 'distance_accuracy_value', 'NONE'); +#81940 = ADVANCED_FACE ( 'NONE', ( #99887 ), #48926, .T. ) ; +#81941 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81942 = CARTESIAN_POINT ( 'NONE', ( -0.1711130133853420165, 2.469409075926969788, 0.8100000000000000533 ) ) ; +#81943 = VERTEX_POINT ( 'NONE', #80079 ) ; +#81944 = SURFACE_SIDE_STYLE ('',( #29301 ) ) ; +#81945 = EDGE_CURVE ( 'NONE', #12127, #8949, #60218, .T. ) ; +#81946 = CARTESIAN_POINT ( 'NONE', ( 1.381066160531370102, -1.463531211619029992, 0.8299999999999994049 ) ) ; +#81947 = CARTESIAN_POINT ( 'NONE', ( -1.285308266724690007, -1.390907012919420094, 0.8299999999999999600 ) ) ; +#81948 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#81950 = ORIENTED_EDGE ( 'NONE', *, *, #19732, .T. ) ; +#81949 = VECTOR ( 'NONE', #71555, 1000.000000000000000 ) ; +#81951 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74753, 'distance_accuracy_value', 'NONE'); +#81952 = PRESENTATION_STYLE_ASSIGNMENT (( #72767 ) ) ; +#81953 = EDGE_CURVE ( 'NONE', #29915, #29795, #88226, .T. ) ; +#81954 = CARTESIAN_POINT ( 'NONE', ( 1.581953864252920283, -1.079063990458369870, 0.8099999999999994982 ) ) ; +#81955 = ORIENTED_EDGE ( 'NONE', *, *, #75585, .F. ) ; +#81956 = ADVANCED_FACE ( 'NONE', ( #24453 ), #33090, .T. ) ; +#81957 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.499999999999980016, -0.02000000000000000042 ) ) ; +#81958 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#81959 = AXIS2_PLACEMENT_3D ( 'NONE', #81054, #81569, #73381 ) ; +#81960 = PLANE ( 'NONE', #58628 ) ; +#81961 = ORIENTED_EDGE ( 'NONE', *, *, #83534, .F. ) ; +#81962 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73786 ) ) ; +#81963 = EDGE_CURVE ( 'NONE', #57896, #21531, #74912, .T. ) ; +#81964 = ORIENTED_EDGE ( 'NONE', *, *, #62596, .F. ) ; +#81966 = VERTEX_POINT ( 'NONE', #75400 ) ; +#81965 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#81967 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#81968 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30573 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35065, #37060, #97769 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81969 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99751 ) ) ; +#81970 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.476179938779914824, 0.000000000000000000 ) ) ; +#81971 = SURFACE_SIDE_STYLE ('',( #43137 ) ) ; +#81972 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81973 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#81974 = ORIENTED_EDGE ( 'NONE', *, *, #66789, .T. ) ; +#81975 = STYLED_ITEM ( 'NONE', ( #100689 ), #18648 ) ; +#81976 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#81977 = EDGE_LOOP ( 'NONE', ( #100517, #9067, #79315, #15501 ) ) ; +#81979 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81978 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#81980 = ORIENTED_EDGE ( 'NONE', *, *, #86091, .T. ) ; +#81981 = VECTOR ( 'NONE', #13835, 1000.000000000000000 ) ; +#81982 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64039 ), #49318 ) ; +#81983 = AXIS2_PLACEMENT_3D ( 'NONE', #18593, #81441, #11372 ) ; +#81985 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#81984 = CARTESIAN_POINT ( 'NONE', ( 0.2560377036815987828, -1.293547069175752240, 0.8100000000000002753 ) ) ; +#81986 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333320425, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#81987 = EDGE_CURVE ( 'NONE', #14472, #71910, #4923, .T. ) ; +#81988 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#81989 = ORIENTED_EDGE ( 'NONE', *, *, #48398, .T. ) ; +#81990 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#81991 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#81992 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65098 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87984, #79836, #40011 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#81993 = ORIENTED_EDGE ( 'NONE', *, *, #44203, .F. ) ; +#81994 = CARTESIAN_POINT ( 'NONE', ( 1.220343482084889963, -1.445215125000139933, 0.8100000000000000533 ) ) ; +#81995 = ORIENTED_EDGE ( 'NONE', *, *, #78944, .T. ) ; +#81996 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#81998 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#81997 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#81999 = CARTESIAN_POINT ( 'NONE', ( -1.145511482700600103, -1.226800916006800080, 0.8299999999999999600 ) ) ; +#82000 = ADVANCED_FACE ( 'NONE', ( #58618 ), #27965, .T. ) ; +#82001 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#82002 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96182 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9501, #16689, #48416 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82003 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#82005 = ADVANCED_FACE ( 'NONE', ( #67230 ), #98308, .F. ) ; +#82004 = CARTESIAN_POINT ( 'NONE', ( 0.4077210354193729902, -1.190630982187130149, 0.8299999999999999600 ) ) ; +#82006 = SURFACE_SIDE_STYLE ('',( #12962 ) ) ; +#82007 = SURFACE_STYLE_USAGE ( .BOTH. , #54505 ) ; +#82008 = CARTESIAN_POINT ( 'NONE', ( 4.832235999999999976, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#82009 = ORIENTED_EDGE ( 'NONE', *, *, #44963, .T. ) ; +#82010 = DIRECTION ( 'NONE', ( 2.168404344971010051E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82011 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82012 = ADVANCED_FACE ( 'NONE', ( #51943 ), #13539, .T. ) ; +#82013 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82015 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 15.15000000000000036, 0.000000000000000000 ) ) ; +#82014 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#82016 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82017 = LINE ( 'NONE', #11956, #65858 ) ; +#82018 = CYLINDRICAL_SURFACE ( 'NONE', #97360, 0.01000000000000002623 ) ; +#82019 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000059508, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#82020 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62328 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82195, #36720, #97461 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82021 = EDGE_LOOP ( 'NONE', ( #78308, #22007, #63909, #23338 ) ) ; +#82022 = CYLINDRICAL_SURFACE ( 'NONE', #96663, 0.05000000000000012768 ) ; +#82023 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.90000000000000036, 0.03429000000000000103 ) ) ; +#82024 = AXIS2_PLACEMENT_3D ( 'NONE', #73715, #19071, #82886 ) ; +#82025 = FILL_AREA_STYLE_COLOUR ( '', #15850 ) ; +#82026 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38830 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62598, #8351, #23272 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82027 = CARTESIAN_POINT ( 'NONE', ( 0.3814764115086780039, -1.210722004796850104, 0.8300000000000015143 ) ) ; +#82028 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #92541, #53280, #84902, #22122 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82029 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.2999999999999999889, -12.44500000000000028 ) ) ; +#82030 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82031 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64092 ) ) ; +#82032 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51874 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20879, #58717, #98400 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82033 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82034 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#82035 = ADVANCED_FACE ( 'NONE', ( #69729 ), #85060, .F. ) ; +#82036 = FILL_AREA_STYLE ('',( #42711 ) ) ; +#82037 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82038 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82039 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#82040 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82041 = SURFACE_SIDE_STYLE ('',( #44201 ) ) ; +#82042 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82043 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82044 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8592 ) ) ; +#82045 = AXIS2_PLACEMENT_3D ( 'NONE', #99488, #69416, #52643 ) ; +#82046 = CARTESIAN_POINT ( 'NONE', ( 1.893542000000000058, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#82047 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #12294, 'design' ) ; +#82048 = PLANE ( 'NONE', #30779 ) ; +#82049 = VECTOR ( 'NONE', #71749, 1000.000000000000000 ) ; +#82050 = ORIENTED_EDGE ( 'NONE', *, *, #38914, .T. ) ; +#82051 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#82052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94317, 'distance_accuracy_value', 'NONE'); +#82053 = EDGE_CURVE ( 'NONE', #74398, #60864, #84073, .T. ) ; +#82054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51754, 'distance_accuracy_value', 'NONE'); +#82055 = VECTOR ( 'NONE', #63325, 1000.000000000000000 ) ; +#82057 = LINE ( 'NONE', #50919, #94292 ) ; +#82056 = FILL_AREA_STYLE_COLOUR ( '', #62320 ) ; +#82058 = ADVANCED_FACE ( 'NONE', ( #100760 ), #51503, .F. ) ; +#82059 = VECTOR ( 'NONE', #1994, 1000.000000000000000 ) ; +#82060 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11368 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84776, #62333, #39844 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82061 = LINE ( 'NONE', #34597, #93305 ) ; +#82062 = SURFACE_SIDE_STYLE ('',( #68196 ) ) ; +#82063 = EDGE_LOOP ( 'NONE', ( #99711, #43851, #14427, #20610, #42291, #31044 ) ) ; +#82064 = CARTESIAN_POINT ( 'NONE', ( -0.3666666666666679730, -3.500000000000000000, 0.000000000000000000 ) ) ; +#82065 = LINE ( 'NONE', #19232, #19648 ) ; +#82066 = FILL_AREA_STYLE ('',( #4419 ) ) ; +#82067 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82068 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#82069 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57018, 'distance_accuracy_value', 'NONE'); +#82070 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82071 = VECTOR ( 'NONE', #6420, 1000.000000000000000 ) ; +#82072 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100673, 'distance_accuracy_value', 'NONE'); +#82073 = VERTEX_POINT ( 'NONE', #66492 ) ; +#82074 = ORIENTED_EDGE ( 'NONE', *, *, #100657, .F. ) ; +#82075 = LINE ( 'NONE', #12013, #1536 ) ; +#82076 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82077 = ORIENTED_EDGE ( 'NONE', *, *, #23520, .F. ) ; +#82078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82079 = LINE ( 'NONE', #59631, #30428 ) ; +#82080 = CARTESIAN_POINT ( 'NONE', ( 1.416666666666666519, -3.099999999999969891, 0.000000000000000000 ) ) ; +#82081 = PRESENTATION_STYLE_ASSIGNMENT (( #18744 ) ) ; +#82082 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #66500, #71143 ) ; +#82083 = PRESENTATION_STYLE_ASSIGNMENT (( #89229 ) ) ; +#82085 = ORIENTED_EDGE ( 'NONE', *, *, #16078, .F. ) ; +#82084 = EDGE_LOOP ( 'NONE', ( #24391, #58147, #84647, #57315 ) ) ; +#82086 = ADVANCED_FACE ( 'NONE', ( #34379 ), #39873, .T. ) ; +#82087 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82088 = ORIENTED_EDGE ( 'NONE', *, *, #43151, .T. ) ; +#82089 = ORIENTED_EDGE ( 'NONE', *, *, #62334, .F. ) ; +#82090 = CARTESIAN_POINT ( 'NONE', ( 1.872286628785889917, -1.103202958186300320, 0.8299999999999995159 ) ) ; +#82091 = CARTESIAN_POINT ( 'NONE', ( 1.892524908602200018, -1.389761831846570095, 0.8100000000000010525 ) ) ; +#82092 = CARTESIAN_POINT ( 'NONE', ( 0.3979805126599459952, -0.9025088801136570416, 0.8299999999999999600 ) ) ; +#82093 = EDGE_LOOP ( 'NONE', ( #25763, #36516, #77544, #93464 ) ) ; +#82094 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15294 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49806, #2330, #64599 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82095 = ADVANCED_FACE ( 'NONE', ( #88474 ), #18511, .F. ) ; +#82096 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82097 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82098 = VECTOR ( 'NONE', #87021, 1000.000000000000000 ) ; +#82099 = CARTESIAN_POINT ( 'NONE', ( -2.499999999999999556, 3.123820061220085265, 0.000000000000000000 ) ) ; +#82100 = ORIENTED_EDGE ( 'NONE', *, *, #60081, .F. ) ; +#82101 = VECTOR ( 'NONE', #60688, 1000.000000000000000 ) ; +#82102 = ORIENTED_EDGE ( 'NONE', *, *, #42519, .T. ) ; +#82103 = STYLED_ITEM ( 'NONE', ( #17477 ), #26114 ) ; +#82104 = ORIENTED_EDGE ( 'NONE', *, *, #11636, .T. ) ; +#82105 = FILL_AREA_STYLE ('',( #97368 ) ) ; +#82106 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#82107 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82108 = EDGE_CURVE ( 'NONE', #96833, #16963, #86581, .T. ) ; +#82109 = SURFACE_STYLE_FILL_AREA ( #35153 ) ; +#82111 = ORIENTED_EDGE ( 'NONE', *, *, #56567, .T. ) ; +#82110 = SURFACE_SIDE_STYLE ('',( #20288 ) ) ; +#82112 = ORIENTED_EDGE ( 'NONE', *, *, #45208, .T. ) ; +#82113 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82114 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#82115 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6994 ), #54413 ) ; +#82116 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82117 = EDGE_LOOP ( 'NONE', ( #16826, #46553, #38475, #4289 ) ) ; +#82119 = SURFACE_SIDE_STYLE ('',( #11055 ) ) ; +#82118 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82120 = ORIENTED_EDGE ( 'NONE', *, *, #85129, .F. ) ; +#82121 = ORIENTED_EDGE ( 'NONE', *, *, #95750, .T. ) ; +#82122 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80506 ) ) ; +#82124 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82123 = PLANE ( 'NONE', #91250 ) ; +#82125 = EDGE_CURVE ( 'NONE', #18846, #39727, #72646, .T. ) ; +#82126 = FACE_OUTER_BOUND ( 'NONE', #12030, .T. ) ; +#82127 = PLANE ( 'NONE', #90548 ) ; +#82128 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82129 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80517 ), #49542 ) ; +#82130 = CARTESIAN_POINT ( 'NONE', ( -0.3663670119008199944, -1.086125944437150048, 0.8100000000000000533 ) ) ; +#82131 = VECTOR ( 'NONE', #5452, 1000.000000000000000 ) ; +#82132 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8648700000000000276 ) ) ; +#82133 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82134 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82135 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82136 = ORIENTED_EDGE ( 'NONE', *, *, #93094, .F. ) ; +#82137 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.600000000000000089, -11.90660254037844012 ) ) ; +#82138 = ORIENTED_EDGE ( 'NONE', *, *, #100828, .F. ) ; +#82139 = STYLED_ITEM ( 'NONE', ( #92233 ), #59979 ) ; +#82140 = ADVANCED_FACE ( 'NONE', ( #26711 ), #8377, .F. ) ; +#82141 = CARTESIAN_POINT ( 'NONE', ( -0.009357855636228630536, -1.039339352017210061, 0.8299999999999999600 ) ) ; +#82142 = CARTESIAN_POINT ( 'NONE', ( 1.416650401028419992, -1.249140550102370018, 0.8100000000000000533 ) ) ; +#82143 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, 1.600000000000000089, -11.82000000000000028 ) ) ; +#82144 = FILL_AREA_STYLE ('',( #59186 ) ) ; +#82145 = PRESENTATION_STYLE_ASSIGNMENT (( #95904 ) ) ; +#82146 = EDGE_CURVE ( 'NONE', #100196, #7176, #22369, .T. ) ; +#82147 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82148 = FILL_AREA_STYLE_COLOUR ( '', #39753 ) ; +#82149 = ORIENTED_EDGE ( 'NONE', *, *, #38854, .T. ) ; +#82150 = FILL_AREA_STYLE_COLOUR ( '', #91181 ) ; +#82151 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#82152 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82153 = VECTOR ( 'NONE', #99630, 1000.000000000000000 ) ; +#82154 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82155 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82156 = EDGE_CURVE ( 'NONE', #56095, #5652, #83834, .T. ) ; +#82158 = EDGE_CURVE ( 'NONE', #3602, #83308, #31772, .T. ) ; +#82157 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82159 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82160 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82161 = SURFACE_STYLE_FILL_AREA ( #43329 ) ; +#82162 = ADVANCED_FACE ( 'NONE', ( #5666 ), #28693, .F. ) ; +#82163 = EDGE_CURVE ( 'NONE', #11727, #62602, #66990, .T. ) ; +#82164 = FACE_OUTER_BOUND ( 'NONE', #81620, .T. ) ; +#82165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69045 ) ) ; +#82166 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84035, 'distance_accuracy_value', 'NONE'); +#82167 = ORIENTED_EDGE ( 'NONE', *, *, #22240, .T. ) ; +#82168 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82169 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82170 = EDGE_LOOP ( 'NONE', ( #61872, #42352, #66394, #63648 ) ) ; +#82171 = CARTESIAN_POINT ( 'NONE', ( 11.21151349949982468, 5.705533499499825467, 0.8991599999999999593 ) ) ; +#82172 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.649999999999999911, -0.02000000000000000042 ) ) ; +#82173 = FILL_AREA_STYLE_COLOUR ( '', #53139 ) ; +#82174 = DIRECTION ( 'NONE', ( -0.3516809254569023269, 0.000000000000000000, 0.9361199317767870953 ) ) ; +#82175 = ADVANCED_FACE ( 'N', ( #21040 ), #30180, .F. ) ; +#82176 = VECTOR ( 'NONE', #92987, 1000.000000000000000 ) ; +#82177 = LINE ( 'NONE', #19355, #45929 ) ; +#82178 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82179 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98394 ), #56077 ) ; +#82180 = VECTOR ( 'NONE', #24056, 1000.000000000000000 ) ; +#82181 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82182 = ORIENTED_EDGE ( 'NONE', *, *, #14276, .F. ) ; +#82183 = STYLED_ITEM ( 'NONE', ( #48610 ), #76344 ) ; +#82184 = ORIENTED_EDGE ( 'NONE', *, *, #14988, .T. ) ; +#82185 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #90721 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#82186 = SURFACE_STYLE_FILL_AREA ( #43349 ) ; +#82187 = FILL_AREA_STYLE_COLOUR ( '', #59273 ) ; +#82188 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15795, 'distance_accuracy_value', 'NONE'); +#82189 = PLANE ( 'NONE', #77322 ) ; +#82190 = CIRCLE ( 'NONE', #51134, 0.01000000000000002623 ) ; +#82191 = PLANE ( 'NONE', #15877 ) ; +#82192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54048, 'distance_accuracy_value', 'NONE'); +#82193 = LINE ( 'NONE', #53913, #26667 ) ; +#82194 = STYLED_ITEM ( 'NONE', ( #95162 ), #21490 ) ; +#82195 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82196 = ORIENTED_EDGE ( 'NONE', *, *, #84951, .T. ) ; +#82197 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59328 ) ) ; +#82198 = FACE_OUTER_BOUND ( 'NONE', #39872, .T. ) ; +#82199 = ORIENTED_EDGE ( 'NONE', *, *, #94935, .F. ) ; +#82200 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#82201 = AXIS2_PLACEMENT_3D ( 'NONE', #67153, #90651, #20693 ) ; +#82202 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82203 = PRESENTATION_STYLE_ASSIGNMENT (( #72499 ) ) ; +#82204 = CARTESIAN_POINT ( 'NONE', ( -1.167182179144840237, -0.9547617453595670378, 0.8299999999999999600 ) ) ; +#82205 = FILL_AREA_STYLE ('',( #83202 ) ) ; +#82207 = ORIENTED_EDGE ( 'NONE', *, *, #92197, .F. ) ; +#82206 = VERTEX_POINT ( 'NONE', #23059 ) ; +#82208 = ORIENTED_EDGE ( 'NONE', *, *, #100458, .F. ) ; +#82209 = FACE_OUTER_BOUND ( 'NONE', #28682, .T. ) ; +#82210 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6742, #77269, #93060, #83451 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82212 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82211 = LINE ( 'NONE', #28564, #45668 ) ; +#82213 = EDGE_LOOP ( 'NONE', ( #31756, #100241, #45033, #128 ) ) ; +#82214 = ADVANCED_FACE ( 'NONE', ( #53689 ), #94477, .F. ) ; +#82215 = ORIENTED_EDGE ( 'NONE', *, *, #54555, .F. ) ; +#82216 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82218 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#82217 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#82219 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#82220 = ORIENTED_EDGE ( 'NONE', *, *, #25888, .T. ) ; +#82221 = ORIENTED_EDGE ( 'NONE', *, *, #14495, .T. ) ; +#82222 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #38535, #55402, #93613, #84982, #46675, #86515, #77836, #70165, #14994, #46153, #69651, #94650, #7798, #16032, #63047, #47194, #47706, #224, #78847, #70677, #31374, #725, #94125, #58433, #11328, #2269, #41077, #26762, #65048, #64048, #56912 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.327616387800421450E-05, 2.547497420769845677E-05, 3.726786310496619462E-05, 4.895517568279224920E-05, 6.099142129639180816E-05, 7.350372333761357889E-05, 8.683811020382510776E-05, 0.0001009728839031329731, 0.0001158868716872430658, 0.0001315611172522268178, 0.0001478298764740817724, 0.0001648923924171857207, 0.0002001775098873845706, 0.0002361870138313680242, 0.0002724555859668259029, 0.0003085720862382314127, 0.0003263295848193640365, 0.0003436214609548974164, 0.0003605877124753401682, 0.0003772653758934155699, 0.0003937700570431823988, 0.0004100899809950210389, 0.0004263483064350540399, 0.0004429971904297568572, 0.0004601179808996606630, 0.0004783389212598614473, 0.0004980104121462203748, 0.0005192903765011231895 ), + .UNSPECIFIED. ) ; +#82223 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16679 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41158, #72795, #65127 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82224 = FILL_AREA_STYLE ('',( #20922 ) ) ; +#82225 = ORIENTED_EDGE ( 'NONE', *, *, #49126, .F. ) ; +#82226 = SURFACE_SIDE_STYLE ('',( #57249 ) ) ; +#82227 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 2.657722526307673226E-34, 0.8648700000000000276 ) ) ; +#82229 = EDGE_LOOP ( 'NONE', ( #27051, #89622, #33777, #88817 ) ) ; +#82228 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#82230 = LINE ( 'NONE', #10151, #48221 ) ; +#82231 = SURFACE_STYLE_FILL_AREA ( #67386 ) ; +#82232 = ORIENTED_EDGE ( 'NONE', *, *, #38110, .T. ) ; +#82233 = PRESENTATION_STYLE_ASSIGNMENT (( #50602 ) ) ; +#82234 = ORIENTED_EDGE ( 'NONE', *, *, #13748, .T. ) ; +#82235 = ORIENTED_EDGE ( 'NONE', *, *, #29681, .T. ) ; +#82236 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23184, #5804, #99187, #15480 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82237 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#82238 = CARTESIAN_POINT ( 'NONE', ( 2.366666666666663144, -3.500000000000000000, 0.000000000000000000 ) ) ; +#82239 = VECTOR ( 'NONE', #30595, 1000.000000000000000 ) ; +#82240 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36612 ), #44657 ) ; +#82241 = PLANE ( 'NONE', #84087 ) ; +#82242 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70858 ), #47970 ) ; +#82243 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42694 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70883, #20718, #45670 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82244 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000444, 0.000000000000000000 ) ) ; +#82246 = LINE ( 'NONE', #19439, #22107 ) ; +#82245 = FILL_AREA_STYLE ('',( #28122 ) ) ; +#82247 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.00000000000000000, 0.000000000000000000 ) ) ; +#82248 = EDGE_LOOP ( 'NONE', ( #60500, #57248, #14164, #43231 ) ) ; +#82249 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82250 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43104 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46418, #71955, #69908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82251 = CARTESIAN_POINT ( 'NONE', ( -1.005612341081159933, -1.485054850390570058, 0.8100000000000000533 ) ) ; +#82252 = ORIENTED_EDGE ( 'NONE', *, *, #58088, .F. ) ; +#82253 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.7000000000000009548, -0.02000000000000000042 ) ) ; +#82254 = FACE_OUTER_BOUND ( 'NONE', #78936, .T. ) ; +#82255 = CARTESIAN_POINT ( 'NONE', ( -0.4248777619592499777, -1.223222257147859926, 0.8300000000000000711 ) ) ; +#82256 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82257 = CIRCLE ( 'NONE', #57794, 0.09999999999999982514 ) ; +#82258 = FILL_AREA_STYLE ('',( #12722 ) ) ; +#82259 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82260 = STYLED_ITEM ( 'NONE', ( #88424 ), #21872 ) ; +#82261 = PRESENTATION_STYLE_ASSIGNMENT (( #26635 ) ) ; +#82262 = LINE ( 'NONE', #43934, #93902 ) ; +#82264 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82263 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69203 ), #25351 ) ; +#82265 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#82266 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41517 ) ) ; +#82267 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82268 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76818 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42618, #79930, #2320 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82269 = FACE_OUTER_BOUND ( 'NONE', #60856, .T. ) ; +#82270 = VECTOR ( 'NONE', #78168, 1000.000000000000000 ) ; +#82271 = ORIENTED_EDGE ( 'NONE', *, *, #37050, .F. ) ; +#82272 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82274 = SURFACE_STYLE_USAGE ( .BOTH. , #75111 ) ; +#82273 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146561808, 0.2541340759269656857, 0.8100000000000000533 ) ) ; +#82275 = SURFACE_STYLE_USAGE ( .BOTH. , #84267 ) ; +#82276 = AXIS2_PLACEMENT_3D ( 'NONE', #85572, #302, #8384 ) ; +#82277 = EDGE_CURVE ( 'NONE', #21592, #86061, #62370, .T. ) ; +#82278 = STYLED_ITEM ( 'NONE', ( #68994 ), #12087 ) ; +#82279 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10208 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84207, #99423, #92346 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82280 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41957, 'distance_accuracy_value', 'NONE'); +#82281 = ORIENTED_EDGE ( 'NONE', *, *, #2104, .F. ) ; +#82282 = CARTESIAN_POINT ( 'NONE', ( -1.114703706423270324, -1.444732071753930036, 0.8299999999999999600 ) ) ; +#82283 = MANIFOLD_SOLID_BREP ( 'ÊäÈë32', #79635 ) ; +#82284 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82285 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077920276, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#82286 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82287 = LINE ( 'NONE', #52645, #33998 ) ; +#82288 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82289 = PLANE ( 'NONE', #39056 ) ; +#82290 = AXIS2_PLACEMENT_3D ( 'NONE', #67010, #19033, #57904 ) ; +#82291 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571421276, 0.7099999999999999645, 0.4999999999999998890 ) ) ; +#82292 = EDGE_CURVE ( 'NONE', #96985, #7769, #32160, .T. ) ; +#82293 = SURFACE_STYLE_FILL_AREA ( #10729 ) ; +#82294 = VERTEX_POINT ( 'NONE', #40398 ) ; +#82295 = VECTOR ( 'NONE', #41194, 1000.000000000000000 ) ; +#82296 = ORIENTED_EDGE ( 'NONE', *, *, #5082, .F. ) ; +#82297 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.383333333333330195, 1.747825839084982648E-76 ) ) ; +#82298 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1984, 'distance_accuracy_value', 'NONE'); +#82299 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#82300 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.2999999999999990452, 0.8299999999999999600 ) ) ; +#82301 = CARTESIAN_POINT ( 'NONE', ( -0.2157361669573319984, -1.030915998478540097, 0.8100000000000000533 ) ) ; +#82302 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8648700000000000276 ) ) ; +#82303 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82304 = SURFACE_STYLE_USAGE ( .BOTH. , #68447 ) ; +#82305 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#82306 = FACE_OUTER_BOUND ( 'NONE', #94466, .T. ) ; +#82307 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75406 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10170, #89888, #35311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82308 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82309 = LINE ( 'NONE', #28660, #26086 ) ; +#82310 = ORIENTED_EDGE ( 'NONE', *, *, #87107, .T. ) ; +#82311 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#82312 = SURFACE_STYLE_FILL_AREA ( #51170 ) ; +#82313 = ORIENTED_EDGE ( 'NONE', *, *, #8762, .T. ) ; +#82314 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82315 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82316 = VECTOR ( 'NONE', #50407, 1000.000000000000000 ) ; +#82317 = FILL_AREA_STYLE ('',( #41497 ) ) ; +#82318 = VERTEX_POINT ( 'NONE', #49068 ) ; +#82319 = CARTESIAN_POINT ( 'NONE', ( 5.929426000000000307, 2.417486999999999941, 0.8648700000000000276 ) ) ; +#82320 = FILL_AREA_STYLE_COLOUR ( '', #80619 ) ; +#82321 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999958471, -0.1458578643762690752 ) ) ; +#82322 = LINE ( 'NONE', #60360, #15287 ) ; +#82323 = ORIENTED_EDGE ( 'NONE', *, *, #13714, .F. ) ; +#82324 = CARTESIAN_POINT ( 'NONE', ( -2.123820061220085265, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#82325 = ORIENTED_EDGE ( 'NONE', *, *, #27447, .F. ) ; +#82326 = VECTOR ( 'NONE', #39795, 1000.000000000000000 ) ; +#82327 = VECTOR ( 'NONE', #22748, 1000.000000000000000 ) ; +#82328 = STYLED_ITEM ( 'NONE', ( #93896 ), #22144 ) ; +#82329 = EDGE_LOOP ( 'NONE', ( #51610, #60348, #33596, #53592 ) ) ; +#82330 = ADVANCED_FACE ( 'NONE', ( #33237 ), #81224, .F. ) ; +#82331 = VERTEX_POINT ( 'NONE', #73037 ) ; +#82332 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69203 ) ) ; +#82333 = SURFACE_STYLE_FILL_AREA ( #20022 ) ; +#82334 = STYLED_ITEM ( 'NONE', ( #31392 ), #98800 ) ; +#82335 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#82336 = PRESENTATION_STYLE_ASSIGNMENT (( #49696 ) ) ; +#82337 = SURFACE_STYLE_FILL_AREA ( #43006 ) ; +#82338 = VERTEX_POINT ( 'NONE', #9652 ) ; +#82339 = ORIENTED_EDGE ( 'NONE', *, *, #74677, .F. ) ; +#82340 = SURFACE_SIDE_STYLE ('',( #42529 ) ) ; +#82341 = ORIENTED_EDGE ( 'NONE', *, *, #88316, .T. ) ; +#82342 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91422 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4559, #52066, #98420 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82343 = VECTOR ( 'NONE', #55983, 1000.000000000000000 ) ; +#82344 = ORIENTED_EDGE ( 'NONE', *, *, #28212, .T. ) ; +#82346 = ORIENTED_EDGE ( 'NONE', *, *, #70513, .T. ) ; +#82345 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82347 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#82348 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#82349 = ORIENTED_EDGE ( 'NONE', *, *, #38898, .F. ) ; +#82350 = FACE_OUTER_BOUND ( 'NONE', #85956, .T. ) ; +#82351 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82352 = LINE ( 'NONE', #59900, #83532 ) ; +#82353 = ORIENTED_EDGE ( 'NONE', *, *, #91425, .F. ) ; +#82354 = EDGE_CURVE ( 'NONE', #81743, #12291, #49573, .T. ) ; +#82355 = PLANE ( 'NONE', #43193 ) ; +#82356 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82357 = STYLED_ITEM ( 'NONE', ( #17493 ), #68296 ) ; +#82358 = FILL_AREA_STYLE_COLOUR ( '', #55175 ) ; +#82359 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66102 ) ) ; +#82360 = EDGE_CURVE ( 'NONE', #2230, #32845, #13858, .T. ) ; +#82361 = SURFACE_STYLE_FILL_AREA ( #5191 ) ; +#82362 = CARTESIAN_POINT ( 'NONE', ( 1.754677333481259982, -1.433486393616560051, 0.8100000000000000533 ) ) ; +#82364 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82363 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.616666666666666252, 0.000000000000000000 ) ) ; +#82365 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#82366 = AXIS2_PLACEMENT_3D ( 'NONE', #78185, #39358, #62886 ) ; +#82367 = ORIENTED_EDGE ( 'NONE', *, *, #15984, .T. ) ; +#82368 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#82369 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90299, #66819, #98388 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82370 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46459 ) ) ; +#82371 = CARTESIAN_POINT ( 'NONE', ( 1.352961788992439907, -1.196758459236680006, 0.8300000000000022915 ) ) ; +#82373 = FILL_AREA_STYLE ('',( #97636 ) ) ; +#82372 = CARTESIAN_POINT ( 'NONE', ( 0.3772639059291220121, -0.9641561732637019544, 0.8299999999999999600 ) ) ; +#82374 = CARTESIAN_POINT ( 'NONE', ( 11.10544712487501329, 4.680228875124988086, 0.8991599999999999593 ) ) ; +#82375 = SURFACE_STYLE_USAGE ( .BOTH. , #90010 ) ; +#82376 = EDGE_CURVE ( 'NONE', #68510, #25439, #41408, .T. ) ; +#82378 = STYLED_ITEM ( 'NONE', ( #31448 ), #49357 ) ; +#82377 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82379 = VECTOR ( 'NONE', #52884, 1000.000000000000000 ) ; +#82380 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82381 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01499999999999998383, 0.1458578643762690474 ) ) ; +#82382 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26997 ) ) ; +#82383 = ORIENTED_EDGE ( 'NONE', *, *, #59129, .F. ) ; +#82384 = AXIS2_PLACEMENT_3D ( 'NONE', #6378, #53410, #13522 ) ; +#82385 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31490, #92734, #32520, #85106 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82386 = FILL_AREA_STYLE ('',( #56907 ) ) ; +#82387 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, 0.000000000000000000 ) ) ; +#82388 = ORIENTED_EDGE ( 'NONE', *, *, #6310, .F. ) ; +#82389 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#82391 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#82390 = STYLED_ITEM ( 'NONE', ( #57350 ), #77102 ) ; +#82392 = SURFACE_STYLE_FILL_AREA ( #36426 ) ; +#82393 = FILL_AREA_STYLE ('',( #90535 ) ) ; +#82394 = CARTESIAN_POINT ( 'NONE', ( -0.2361504354203300127, -1.354501511147599979, 0.8100000000000000533 ) ) ; +#82395 = FACE_OUTER_BOUND ( 'NONE', #27838, .T. ) ; +#82396 = EDGE_CURVE ( 'NONE', #28558, #45692, #57690, .T. ) ; +#82397 = STYLED_ITEM ( 'NONE', ( #33313 ), #20578 ) ; +#82398 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#82399 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4974 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6238, #29776, #30773 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82400 = VERTEX_POINT ( 'NONE', #2591 ) ; +#82401 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#82402 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#82403 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82406 = VECTOR ( 'NONE', #86621, 1000.000000000000000 ) ; +#82405 = STYLED_ITEM ( 'NONE', ( #57372 ), #38614 ) ; +#82404 = SURFACE_STYLE_FILL_AREA ( #42086 ) ; +#82407 = CARTESIAN_POINT ( 'NONE', ( 1.137126380867480080, -0.8900438058027670962, 0.8299999999999994049 ) ) ; +#82408 = CARTESIAN_POINT ( 'NONE', ( 1.198411601801520066, -1.515412412365080064, 0.8300000000000010703 ) ) ; +#82409 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82410 = PLANE ( 'NONE', #88961 ) ; +#82411 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.000000000000000000 ) ) ; +#82412 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8648700000000000276 ) ) ; +#82413 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#82414 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, -5.403663627667755085E-17, -0.8499999999999999778 ) ) ; +#82415 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88889 ), #13817 ) ; +#82416 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82417 = ADVANCED_FACE ( 'NONE', ( #64369 ), #72039, .T. ) ; +#82418 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82419 = SURFACE_STYLE_FILL_AREA ( #58462 ) ; +#82420 = ORIENTED_EDGE ( 'NONE', *, *, #40999, .F. ) ; +#82421 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82422 = ORIENTED_EDGE ( 'NONE', *, *, #83946, .T. ) ; +#82423 = CARTESIAN_POINT ( 'NONE', ( 1.065702489232140060, -1.018544155089240011, 0.8100000000000000533 ) ) ; +#82424 = SURFACE_STYLE_FILL_AREA ( #4294 ) ; +#82425 = DIRECTION ( 'NONE', ( -1.836970198721029688E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82426 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#82427 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82428 = SURFACE_SIDE_STYLE ('',( #42113 ) ) ; +#82429 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333333304, 2.700000000000000178, 0.000000000000000000 ) ) ; +#82430 = CARTESIAN_POINT ( 'NONE', ( 0.5255026765280939038, -0.9746087015134969889, 0.8100000000000001643 ) ) ; +#82431 = ORIENTED_EDGE ( 'NONE', *, *, #73964, .T. ) ; +#82432 = CARTESIAN_POINT ( 'NONE', ( 1.037938936489817277, -1.349629322163836465, 0.8099999999997700151 ) ) ; +#82433 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#82434 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100211 ), #46524 ) ; +#82435 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82436 = ORIENTED_EDGE ( 'NONE', *, *, #88579, .T. ) ; +#82437 = ADVANCED_FACE ( 'NONE', ( #90352 ), #44368, .T. ) ; +#82438 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46960 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47044, #16886, #38895 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82439 = CARTESIAN_POINT ( 'NONE', ( -1.250988841353219971, -1.419390247362990021, 0.8299999999999999600 ) ) ; +#82440 = VERTEX_POINT ( 'NONE', #36745 ) ; +#82441 = FILL_AREA_STYLE ('',( #6260 ) ) ; +#82442 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82443 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8481 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58150, #34158, #33645 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82444 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82445 = CARTESIAN_POINT ( 'NONE', ( -1.350000000000000089, 3.099999999999989875, 0.000000000000000000 ) ) ; +#82446 = EDGE_CURVE ( 'NONE', #27582, #25575, #68364, .T. ) ; +#82447 = MANIFOLD_SOLID_BREP ( 'ÊäÈë38', #64887 ) ; +#82448 = ORIENTED_EDGE ( 'NONE', *, *, #39693, .F. ) ; +#82449 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98399 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8391, #68728, #46758 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82450 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12235 ) ) ; +#82451 = PRESENTATION_STYLE_ASSIGNMENT (( #12906 ) ) ; +#82452 = SURFACE_STYLE_USAGE ( .BOTH. , #36988 ) ; +#82453 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82454 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82455 = SURFACE_SIDE_STYLE ('',( #51813 ) ) ; +#82456 = STYLED_ITEM ( 'NONE', ( #78401 ), #48712 ) ; +#82457 = ORIENTED_EDGE ( 'NONE', *, *, #85311, .F. ) ; +#82458 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84049 ), #35172 ) ; +#82459 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82460 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #9634, #66853 ), + ( #36239, #20897 ), + ( #58242, #75043 ), + ( #11638, #43872 ), + ( #27576, #89342 ), + ( #52557, #90337 ), + ( #60242, #42879 ), + ( #11139, #67349 ), + ( #42392, #91346 ), + ( #19388, #83201 ), + ( #5038, #67835 ), + ( #98418, #66366 ), + ( #4069, #4557 ), + ( #50569, #35749 ), + ( #35253, #58737 ), + ( #97938, #19894 ), + ( #90850, #81706 ), + ( #28554, #52064 ), + ( #73529, #89838 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07093303484184700081, 0.1380728745211050046, 0.2018606155235370125, 0.2626916650326779901, 0.3217768640876429997, 0.3790524062085789958, 0.4356238423959519768, 0.4920721967161360011, 0.5487618468155189833, 0.6056749686055149517, 0.6640808602740010391, 0.7243245171839870489, 0.7877911482556440026, 0.8544436180341159481, 0.9248994808183850225, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82461 = VECTOR ( 'NONE', #71530, 1000.000000000000000 ) ; +#82462 = ORIENTED_EDGE ( 'NONE', *, *, #289, .T. ) ; +#82464 = VERTEX_POINT ( 'NONE', #29085 ) ; +#82463 = PLANE ( 'NONE', #73739 ) ; +#82466 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65275 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20482, #51667, #90429 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82465 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82732, 'distance_accuracy_value', 'NONE'); +#82467 = FILL_AREA_STYLE ('',( #83459 ) ) ; +#82468 = CARTESIAN_POINT ( 'NONE', ( -1.390280071815130025, -1.351356007592219965, 0.8100000000000000533 ) ) ; +#82469 = FILL_AREA_STYLE_COLOUR ( '', #49691 ) ; +#82471 = STYLED_ITEM ( 'NONE', ( #36340 ), #22905 ) ; +#82470 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#82472 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#82473 = PLANE ( 'NONE', #53243 ) ; +#82474 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.899999999999999911, 0.000000000000000000 ) ) ; +#82475 = EDGE_LOOP ( 'NONE', ( #13122, #68750, #57118, #63393 ) ) ; +#82476 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9232 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8644, #79723, #73557 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82477 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82478 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999990230, -0.02000000000000000042 ) ) ; +#82479 = ORIENTED_EDGE ( 'NONE', *, *, #16300, .F. ) ; +#82480 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82481 = ORIENTED_EDGE ( 'NONE', *, *, #3060, .T. ) ; +#82482 = EDGE_CURVE ( 'NONE', #90877, #90252, #75537, .T. ) ; +#82483 = VECTOR ( 'NONE', #8164, 1000.000000000000000 ) ; +#82484 = EDGE_CURVE ( 'NONE', #35156, #34142, #28094, .T. ) ; +#82486 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82485 = FILL_AREA_STYLE ('',( #27869 ) ) ; +#82487 = CYLINDRICAL_SURFACE ( 'NONE', #76632, 0.1000000000000000056 ) ; +#82488 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.266666666666667052, 0.000000000000000000 ) ) ; +#82489 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97160 ) ) ; +#82490 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82491 = LINE ( 'NONE', #27357, #73534 ) ; +#82492 = VERTEX_POINT ( 'NONE', #76040 ) ; +#82493 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999998557, 0.7578679656440356904, -0.2000000000000000111 ) ) ; +#82494 = ORIENTED_EDGE ( 'NONE', *, *, #8234, .F. ) ; +#82495 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82496 = EDGE_CURVE ( 'NONE', #63874, #73986, #77460, .T. ) ; +#82497 = EDGE_CURVE ( 'NONE', #58513, #75418, #36255, .T. ) ; +#82499 = EDGE_CURVE ( 'NONE', #17472, #25602, #14202, .T. ) ; +#82498 = PRESENTATION_STYLE_ASSIGNMENT (( #61029 ) ) ; +#82500 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77597 ), #58110 ) ; +#82501 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#82502 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82503 = ORIENTED_EDGE ( 'NONE', *, *, #75923, .F. ) ; +#82504 = SURFACE_STYLE_USAGE ( .BOTH. , #27896 ) ; +#82506 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82505 = FILL_AREA_STYLE ('',( #58047 ) ) ; +#82508 = FILL_AREA_STYLE ('',( #89659 ) ) ; +#82507 = CARTESIAN_POINT ( 'NONE', ( 5.130395124874956636, 4.135756875125044196, 0.8991599999999999593 ) ) ; +#82509 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74618, 'distance_accuracy_value', 'NONE'); +#82510 = LINE ( 'NONE', #88644, #10895 ) ; +#82512 = MANIFOLD_SOLID_BREP ( 'ÊäÈë142', #20785 ) ; +#82511 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 9.949999999999999289, 0.000000000000000000 ) ) ; +#82513 = EDGE_CURVE ( 'NONE', #65011, #7186, #54072, .T. ) ; +#82514 = VECTOR ( 'NONE', #31994, 1000.000000000000000 ) ; +#82515 = VECTOR ( 'NONE', #62332, 1000.000000000000000 ) ; +#82516 = VECTOR ( 'NONE', #53625, 1000.000000000000114 ) ; +#82517 = CARTESIAN_POINT ( 'NONE', ( 5.519303750250086793, 9.700686750250087087, 0.8991599999999999593 ) ) ; +#82518 = VERTEX_POINT ( 'NONE', #27597 ) ; +#82519 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15630 ), #33620 ) ; +#82521 = EDGE_CURVE ( 'NONE', #39075, #76537, #8508, .T. ) ; +#82520 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8991599999999999593 ) ) ; +#82522 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82523 = FILL_AREA_STYLE ('',( #43189 ) ) ; +#82524 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#82525 = PLANE ( 'NONE', #83290 ) ; +#82526 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#82527 = FACE_OUTER_BOUND ( 'NONE', #93827, .T. ) ; +#82528 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#82529 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82530 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #4983, #11075, #12599, #3521 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82531 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#82532 = EDGE_CURVE ( 'NONE', #47678, #84098, #38250, .T. ) ; +#82534 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#82533 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36821 ), #74364 ) ; +#82535 = SURFACE_STYLE_FILL_AREA ( #36579 ) ; +#82536 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82537 = ADVANCED_FACE ( 'NONE', ( #32103 ), #70903, .F. ) ; +#82538 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#82539 = LINE ( 'NONE', #50907, #13503 ) ; +#82540 = LINE ( 'NONE', #49016, #73181 ) ; +#82541 = CARTESIAN_POINT ( 'NONE', ( -0.2758995662929830117, -0.9966931238414048488, 0.8300000000000009592 ) ) ; +#82542 = SURFACE_STYLE_FILL_AREA ( #12492 ) ; +#82543 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82544 = VERTEX_POINT ( 'NONE', #949 ) ; +#82545 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#82546 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#82547 = AXIS2_PLACEMENT_3D ( 'NONE', #31159, #66207, #48523 ) ; +#82548 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82550 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.123820061220075051, -0.02000000000000000042 ) ) ; +#82549 = FACE_OUTER_BOUND ( 'NONE', #10732, .T. ) ; +#82551 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8299999999999999600 ) ) ; +#82552 = VECTOR ( 'NONE', #77540, 1000.000000000000000 ) ; +#82553 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#82554 = EDGE_CURVE ( 'NONE', #17472, #32273, #15734, .T. ) ; +#82555 = VERTEX_POINT ( 'NONE', #69338 ) ; +#82556 = SURFACE_STYLE_USAGE ( .BOTH. , #12001 ) ; +#82557 = FACE_OUTER_BOUND ( 'NONE', #48336, .T. ) ; +#82558 = VECTOR ( 'NONE', #4353, 1000.000000000000000 ) ; +#82559 = EDGE_LOOP ( 'NONE', ( #16454, #4204, #42666, #16354 ) ) ; +#82560 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#82561 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82562 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82563 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82564 = CARTESIAN_POINT ( 'NONE', ( -1.227650000060198643E-05, -5.189999992272209539E-08, 0.02000000000000005246 ) ) ; +#82565 = ADVANCED_FACE ( 'NONE', ( #78543 ), #22411, .T. ) ; +#82566 = VERTEX_POINT ( 'NONE', #88243 ) ; +#82567 = ORIENTED_EDGE ( 'NONE', *, *, #39964, .T. ) ; +#82568 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82569 = ORIENTED_EDGE ( 'NONE', *, *, #50945, .F. ) ; +#82570 = CARTESIAN_POINT ( 'NONE', ( 1.788063499344580087, -1.247965265924660061, 0.8299999999999999600 ) ) ; +#82571 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53260 ), #32056 ) ; +#82572 = FILL_AREA_STYLE ('',( #27442 ) ) ; +#82573 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.03429000000000000103 ) ) ; +#82574 = FACE_OUTER_BOUND ( 'NONE', #81741, .T. ) ; +#82575 = PRESENTATION_STYLE_ASSIGNMENT (( #51452 ) ) ; +#82576 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #77881, #58257 ) ; +#82577 = SURFACE_STYLE_FILL_AREA ( #59122 ) ; +#82579 = ORIENTED_EDGE ( 'NONE', *, *, #5192, .F. ) ; +#82578 = VERTEX_POINT ( 'NONE', #64747 ) ; +#82580 = EDGE_LOOP ( 'NONE', ( #87748, #87527, #87760, #74515 ) ) ; +#82581 = ORIENTED_EDGE ( 'NONE', *, *, #91417, .T. ) ; +#82582 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#82583 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32067 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9962, #17691, #2408 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82584 = VECTOR ( 'NONE', #32898, 1000.000000000000114 ) ; +#82585 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7543, 'distance_accuracy_value', 'NONE'); +#82587 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000985, -0.1400000000000000133 ) ) ; +#82586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82588 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36632 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60673, #22341, #52013 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82589 = DIRECTION ( 'NONE', ( 0.7071090539100497452, -0.7071045084557405769, 0.000000000000000000 ) ) ; +#82590 = CARTESIAN_POINT ( 'NONE', ( 8.969985499500047865, 9.983529499500052751, 0.8991599999999999593 ) ) ; +#82591 = AXIS2_PLACEMENT_3D ( 'NONE', #89513, #74188, #91006 ) ; +#82592 = PRESENTATION_STYLE_ASSIGNMENT (( #37136 ) ) ; +#82593 = ORIENTED_EDGE ( 'NONE', *, *, #13338, .F. ) ; +#82594 = VECTOR ( 'NONE', #59632, 1000.000000000000000 ) ; +#82595 = PRESENTATION_STYLE_ASSIGNMENT (( #90740 ) ) ; +#82596 = ORIENTED_EDGE ( 'NONE', *, *, #51217, .F. ) ; +#82597 = ORIENTED_EDGE ( 'NONE', *, *, #16985, .F. ) ; +#82598 = EDGE_CURVE ( 'NONE', #51323, #20411, #41779, .T. ) ; +#82599 = CARTESIAN_POINT ( 'NONE', ( 1.006730632090929944, -1.141526082476280068, 0.8299999999999999600 ) ) ; +#82600 = FILL_AREA_STYLE_COLOUR ( '', #65807 ) ; +#82601 = CARTESIAN_POINT ( 'NONE', ( 1.899701586460730285, -1.304291937284929981, 0.8300000000000004041 ) ) ; +#82602 = STYLED_ITEM ( 'NONE', ( #93749 ), #62086 ) ; +#82603 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999889, -1.665334536937739988E-17 ) ) ; +#82605 = VERTEX_POINT ( 'NONE', #49959 ) ; +#82604 = FILL_AREA_STYLE ('',( #96369 ) ) ; +#82606 = SURFACE_SIDE_STYLE ('',( #42789 ) ) ; +#82607 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#82608 = SURFACE_STYLE_FILL_AREA ( #60156 ) ; +#82609 = ORIENTED_EDGE ( 'NONE', *, *, #84141, .F. ) ; +#82610 = FILL_AREA_STYLE ('',( #59161 ) ) ; +#82611 = ORIENTED_EDGE ( 'NONE', *, *, #84141, .T. ) ; +#82612 = ORIENTED_EDGE ( 'NONE', *, *, #85865, .T. ) ; +#82614 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82613 = LINE ( 'NONE', #12069, #50771 ) ; +#82615 = MANIFOLD_SOLID_BREP ( 'ÊäÈë173', #59971 ) ; +#82616 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #11482, #75363, #96808, #21236, #81563, #83536, #52398, #43705, #58582, #50425, #97308, #97787, #42719, #73866, #27926, #65700, #3908 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.217060269204701879E-05, 4.373712411657710122E-05, 5.438460671129744629E-05, 6.481866320469819220E-05, 7.490038279277670187E-05, 8.498210238085484561E-05, 9.503964954003633631E-05, 0.0001051177103656686894, 0.0001153266605817822408, 0.0001258150082380597712, 0.0001366635663297268235, 0.0001477422118352548727, 0.0001591650473074340778, 0.0001710833825230673275 ), + .UNSPECIFIED. ) ; +#82617 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41805 ), #48447 ) ; +#82618 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82619 = ADVANCED_FACE ( 'NONE', ( #1967 ), #18251, .F. ) ; +#82620 = PLANE ( 'NONE', #55742 ) ; +#82621 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#82622 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89177 ) ) ; +#82623 = CARTESIAN_POINT ( 'NONE', ( -1.141923701298700022, -1.445454545454550210, 0.8299999999999999600 ) ) ; +#82624 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58479, 'distance_accuracy_value', 'NONE'); +#82625 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82626 = ORIENTED_EDGE ( 'NONE', *, *, #88921, .T. ) ; +#82627 = SURFACE_STYLE_FILL_AREA ( #37172 ) ; +#82628 = ORIENTED_EDGE ( 'NONE', *, *, #27602, .T. ) ; +#82629 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30070 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62020, #100177, #16503 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82630 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#82631 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82632 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#82633 = ORIENTED_EDGE ( 'NONE', *, *, #37891, .F. ) ; +#82634 = FILL_AREA_STYLE_COLOUR ( '', #41173 ) ; +#82635 = SURFACE_SIDE_STYLE ('',( #59191 ) ) ; +#82636 = SURFACE_SIDE_STYLE ('',( #43820 ) ) ; +#82637 = SURFACE_SIDE_STYLE ('',( #738 ) ) ; +#82638 = FILL_AREA_STYLE_COLOUR ( '', #92385 ) ; +#82639 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#82640 = AXIS2_PLACEMENT_3D ( 'NONE', #41329, #94886, #39794 ) ; +#82641 = SURFACE_SIDE_STYLE ('',( #71593 ) ) ; +#82642 = STYLED_ITEM ( 'NONE', ( #82261 ), #30463 ) ; +#82643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82644 = ADVANCED_FACE ( 'NONE', ( #34635 ), #95380, .F. ) ; +#82645 = FILL_AREA_STYLE_COLOUR ( '', #14309 ) ; +#82646 = PLANE ( 'NONE', #72383 ) ; +#82647 = SURFACE_STYLE_USAGE ( .BOTH. , #12113 ) ; +#82648 = STYLED_ITEM ( 'NONE', ( #92164 ), #83928 ) ; +#82649 = ORIENTED_EDGE ( 'NONE', *, *, #55327, .T. ) ; +#82650 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82651 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82652 = ORIENTED_EDGE ( 'NONE', *, *, #99778, .T. ) ; +#82653 = SURFACE_STYLE_USAGE ( .BOTH. , #34210 ) ; +#82655 = STYLED_ITEM ( 'NONE', ( #51888 ), #55071 ) ; +#82654 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82656 = LINE ( 'NONE', #67802, #80709 ) ; +#82658 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#82657 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82660 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.500000000000000444, 0.000000000000000000 ) ) ; +#82659 = STYLED_ITEM ( 'NONE', ( #58293 ), #79246 ) ; +#82661 = CARTESIAN_POINT ( 'NONE', ( 1.396920551461607873, -0.9843154279477446256, 0.8099999999999996092 ) ) ; +#82662 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82663 = CIRCLE ( 'NONE', #40329, 1.293010265664959801 ) ; +#82664 = PRESENTATION_STYLE_ASSIGNMENT (( #28056 ) ) ; +#82665 = ORIENTED_EDGE ( 'NONE', *, *, #19080, .T. ) ; +#82666 = VERTEX_POINT ( 'NONE', #91720 ) ; +#82667 = AXIS2_PLACEMENT_3D ( 'NONE', #48102, #44673, #1649 ) ; +#82668 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82669 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82670 = PLANE ( 'NONE', #73250 ) ; +#82671 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85869 ), #67908 ) ; +#82672 = SURFACE_SIDE_STYLE ('',( #35731 ) ) ; +#82673 = LINE ( 'NONE', #19877, #51861 ) ; +#82674 = PRESENTATION_STYLE_ASSIGNMENT (( #66840 ) ) ; +#82675 = SHAPE_REPRESENTATION ( 'L0201_20210301.xtd', ( #82894 ), #55160 ) ; +#82676 = CLOSED_SHELL ( 'NONE', ( #3538, #32232, #78786, #38866, #48321, #74448, #57571, #10348, #98518, #99902, #25905, #72119, #49707, #50347 ) ) ; +#82677 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82678 = EDGE_CURVE ( 'NONE', #31830, #29934, #35644, .T. ) ; +#82679 = ORIENTED_EDGE ( 'NONE', *, *, #37492, .F. ) ; +#82680 = ORIENTED_EDGE ( 'NONE', *, *, #89220, .F. ) ; +#82681 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25625 ) ) ; +#82682 = VERTEX_POINT ( 'NONE', #3963 ) ; +#82683 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82684 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25627 ) ) ; +#82685 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82686 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82687 = STYLED_ITEM ( 'NONE', ( #78682 ), #14525 ) ; +#82688 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 8.696595000000000297, 0.8991599999999999593 ) ) ; +#82689 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.000000000000000000, -11.57000000000000028 ) ) ; +#82691 = ORIENTED_EDGE ( 'NONE', *, *, #72804, .T. ) ; +#82690 = ORIENTED_EDGE ( 'NONE', *, *, #87544, .F. ) ; +#82692 = EDGE_CURVE ( 'NONE', #25575, #6650, #94127, .T. ) ; +#82693 = ORIENTED_EDGE ( 'NONE', *, *, #48880, .F. ) ; +#82694 = STYLED_ITEM ( 'NONE', ( #60380 ), #13404 ) ; +#82695 = CARTESIAN_POINT ( 'NONE', ( 1.549517223800989996, -0.9663557550577258626, 0.8099999999999981659 ) ) ; +#82696 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8877, 'distance_accuracy_value', 'NONE'); +#82697 = SURFACE_STYLE_USAGE ( .BOTH. , #43883 ) ; +#82698 = VERTEX_POINT ( 'NONE', #97362 ) ; +#82699 = ADVANCED_FACE ( 'NONE', ( #51467 ), #309, .T. ) ; +#82700 = ORIENTED_EDGE ( 'NONE', *, *, #80908, .T. ) ; +#82701 = SURFACE_STYLE_USAGE ( .BOTH. , #19402 ) ; +#82702 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82703 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82704 = AXIS2_PLACEMENT_3D ( 'NONE', #98530, #4680, #13268 ) ; +#82706 = LINE ( 'NONE', #99908, #56415 ) ; +#82705 = SURFACE_SIDE_STYLE ('',( #91361 ) ) ; +#82707 = SURFACE_STYLE_USAGE ( .BOTH. , #13687 ) ; +#82708 = VERTEX_POINT ( 'NONE', #53453 ) ; +#82709 = EDGE_LOOP ( 'NONE', ( #87347, #65583, #25484, #51070 ) ) ; +#82710 = LINE ( 'NONE', #59779, #7746 ) ; +#82711 = ORIENTED_EDGE ( 'NONE', *, *, #1491, .T. ) ; +#82712 = ADVANCED_FACE ( 'NONE', ( #93701 ), #70254, .F. ) ; +#82713 = EDGE_CURVE ( 'NONE', #9763, #2230, #62638, .T. ) ; +#82716 = EDGE_CURVE ( 'NONE', #75149, #82400, #70766, .T. ) ; +#82715 = VERTEX_POINT ( 'NONE', #39630 ) ; +#82714 = LINE ( 'NONE', #43903, #13520 ) ; +#82717 = EDGE_CURVE ( 'NONE', #21432, #86972, #46239, .T. ) ; +#82718 = STYLED_ITEM ( 'NONE', ( #49015 ), #84225 ) ; +#82719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45137 ), #55041 ) ; +#82720 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#82721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82722 = EDGE_LOOP ( 'NONE', ( #94687, #47872, #97843, #1248 ) ) ; +#82723 = FACE_OUTER_BOUND ( 'NONE', #2370, .T. ) ; +#82724 = ORIENTED_EDGE ( 'NONE', *, *, #21409, .F. ) ; +#82725 = VERTEX_POINT ( 'NONE', #16111 ) ; +#82726 = FILL_AREA_STYLE ('',( #91382 ) ) ; +#82727 = STYLED_ITEM ( 'NONE', ( #31268 ), #55312 ) ; +#82728 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82729 = ADVANCED_FACE ( 'NONE', ( #822 ), #22808, .T. ) ; +#82730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85920 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45506, #92494, #69001 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82731 = SURFACE_STYLE_FILL_AREA ( #14739 ) ; +#82732 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82733 = EDGE_CURVE ( 'NONE', #98110, #96275, #86593, .T. ) ; +#82734 = FACE_OUTER_BOUND ( 'NONE', #28124, .T. ) ; +#82736 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82735 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#82737 = DIRECTION ( 'NONE', ( -0.7071067811865465735, -0.7071067811865483499, 0.000000000000000000 ) ) ; +#82738 = ORIENTED_EDGE ( 'NONE', *, *, #50644, .T. ) ; +#82739 = STYLED_ITEM ( 'NONE', ( #80204 ), #24026 ) ; +#82740 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90411, #45416, #60806 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82741 = ORIENTED_EDGE ( 'NONE', *, *, #39360, .F. ) ; +#82742 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#82743 = CARTESIAN_POINT ( 'NONE', ( -0.1950643281718389965, -1.495500525511030077, 0.8299999999999999600 ) ) ; +#82744 = STYLED_ITEM ( 'NONE', ( #1792 ), #41119 ) ; +#82745 = STYLED_ITEM ( 'NONE', ( #81330 ), #16309 ) ; +#82746 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82747 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23724 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5999, #59232, #99871 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82749 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999956, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#82748 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82750 = SURFACE_SIDE_STYLE ('',( #12212 ) ) ; +#82751 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#82752 = CLOSED_SHELL ( 'NONE', ( #90919, #38736, #29627, #11714, #43971, #9664 ) ) ; +#82753 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999996181, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#82754 = AXIS2_PLACEMENT_3D ( 'NONE', #38546, #61555, #100204 ) ; +#82755 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #60754, #83726, #45370, #100410 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#82756 = STYLED_ITEM ( 'NONE', ( #69955 ), #100475 ) ; +#82757 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#82758 = VECTOR ( 'NONE', #43538, 1000.000000000000000 ) ; +#82759 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#82760 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #55009 ), #72924 ) ; +#82761 = PLANE ( 'NONE', #1616 ) ; +#82762 = EDGE_CURVE ( 'NONE', #81738, #39791, #88227, .T. ) ; +#82763 = AXIS2_PLACEMENT_3D ( 'NONE', #46832, #100348, #86148 ) ; +#82764 = EDGE_CURVE ( 'NONE', #88846, #97585, #95730, .T. ) ; +#82765 = ORIENTED_EDGE ( 'NONE', *, *, #74459, .F. ) ; +#82766 = CARTESIAN_POINT ( 'NONE', ( -0.9967138265693971100, -1.378727886756609955, 0.8100000000000000533 ) ) ; +#82767 = MANIFOLD_SOLID_BREP ( 'ÊäÈë90', #53447 ) ; +#82768 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.000000000000000000 ) ) ; +#82769 = CYLINDRICAL_SURFACE ( 'NONE', #82045, 0.04999999999999991257 ) ; +#82770 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82771 = FACE_OUTER_BOUND ( 'NONE', #87733, .T. ) ; +#82772 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#82773 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82054 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51754, #59935, #29739 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82774 = PRESENTATION_STYLE_ASSIGNMENT (( #66444 ) ) ; +#82775 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#82776 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82777 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#82778 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82779 = ORIENTED_EDGE ( 'NONE', *, *, #16225, .T. ) ; +#82780 = FILL_AREA_STYLE_COLOUR ( '', #17202 ) ; +#82781 = EDGE_LOOP ( 'NONE', ( #5761, #96187, #51602, #2214 ) ) ; +#82782 = PLANE ( 'NONE', #73153 ) ; +#82783 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72223, 'distance_accuracy_value', 'NONE'); +#82784 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80923, 'distance_accuracy_value', 'NONE'); +#82785 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8648700000000000276 ) ) ; +#82786 = PRESENTATION_STYLE_ASSIGNMENT (( #75620 ) ) ; +#82787 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82788 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89349 ), #4493 ) ; +#82789 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15917 ), #86056 ) ; +#82790 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#82791 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#82792 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82793 = LINE ( 'NONE', #58348, #63624 ) ; +#82794 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#82795 = EDGE_LOOP ( 'NONE', ( #70966, #48817, #86844, #53328 ) ) ; +#82796 = SURFACE_SIDE_STYLE ('',( #75150 ) ) ; +#82798 = ADVANCED_FACE ( 'NONE', ( #2856 ), #88604, .T. ) ; +#82797 = FILL_AREA_STYLE ('',( #74643 ) ) ; +#82799 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#82800 = ORIENTED_EDGE ( 'NONE', *, *, #33848, .F. ) ; +#82801 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000006162, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#82802 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82803 = ORIENTED_EDGE ( 'NONE', *, *, #35937, .T. ) ; +#82804 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#82805 = VECTOR ( 'NONE', #25851, 1000.000000000000000 ) ; +#82806 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8648700000000000276 ) ) ; +#82807 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #89242, #64824 ) ; +#82808 = FACE_OUTER_BOUND ( 'NONE', #79409, .T. ) ; +#82809 = FILL_AREA_STYLE ('',( #28678 ) ) ; +#82810 = VERTEX_POINT ( 'NONE', #43145 ) ; +#82811 = SURFACE_STYLE_USAGE ( .BOTH. , #81831 ) ; +#82813 = VECTOR ( 'NONE', #41979, 1000.000000000000000 ) ; +#82812 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#82814 = VERTEX_POINT ( 'NONE', #13435 ) ; +#82815 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60025 ), #84405 ) ; +#82816 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#82817 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97873 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33593, #49924, #42254 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82818 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#82819 = CLOSED_SHELL ( 'NONE', ( #94920, #99068, #87776, #67691, #15001, #51511 ) ) ; +#82820 = EDGE_LOOP ( 'NONE', ( #15987, #91396, #31604, #59928 ) ) ; +#82821 = EDGE_CURVE ( 'NONE', #70891, #11295, #74804, .T. ) ; +#82822 = EDGE_LOOP ( 'NONE', ( #82948, #19898, #65521, #71394 ) ) ; +#82823 = VECTOR ( 'NONE', #10423, 1000.000000000000114 ) ; +#82824 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#82825 = CARTESIAN_POINT ( 'NONE', ( -0.4939079156693390038, -1.173538053626689948, 0.8100000000000000533 ) ) ; +#82826 = SURFACE_STYLE_USAGE ( .BOTH. , #51701 ) ; +#82827 = SURFACE_SIDE_STYLE ('',( #90478 ) ) ; +#82829 = VERTEX_POINT ( 'NONE', #97726 ) ; +#82828 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56769 ), #89463 ) ; +#82830 = EDGE_LOOP ( 'NONE', ( #43019, #2444, #53588, #39485 ) ) ; +#82831 = ORIENTED_EDGE ( 'NONE', *, *, #50866, .F. ) ; +#82832 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82833 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2808578643762702498, 0.1434314575050751328 ) ) ; +#82836 = ORIENTED_EDGE ( 'NONE', *, *, #76447, .F. ) ; +#82835 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82834 = SURFACE_STYLE_FILL_AREA ( #58892 ) ; +#82837 = EDGE_CURVE ( 'NONE', #28251, #27329, #67126, .T. ) ; +#82838 = LINE ( 'NONE', #44503, #30188 ) ; +#82839 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#82840 = FILL_AREA_STYLE_COLOUR ( '', #35867 ) ; +#82841 = VERTEX_POINT ( 'NONE', #3843 ) ; +#82842 = CARTESIAN_POINT ( 'NONE', ( -2.033333333333333659, -3.500000000000000000, 0.000000000000000000 ) ) ; +#82843 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82844 = FILL_AREA_STYLE_COLOUR ( '', #18261 ) ; +#82845 = ORIENTED_EDGE ( 'NONE', *, *, #71200, .T. ) ; +#82846 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#82847 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82848 = CARTESIAN_POINT ( 'NONE', ( 0.001420454545454360095, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#82849 = AXIS2_PLACEMENT_3D ( 'NONE', #43372, #67834, #51579 ) ; +#82850 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82851 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#82852 = EDGE_CURVE ( 'NONE', #1733, #10027, #28343, .T. ) ; +#82853 = CARTESIAN_POINT ( 'NONE', ( 1.823289888948260051, -1.336414498567920051, 0.8299999999999999600 ) ) ; +#82855 = SURFACE_SIDE_STYLE ('',( #12319 ) ) ; +#82854 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82856 = VECTOR ( 'NONE', #98122, 1000.000000000000000 ) ; +#82857 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#82858 = ORIENTED_EDGE ( 'NONE', *, *, #100879, .F. ) ; +#82859 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82860 = CARTESIAN_POINT ( 'NONE', ( 1.084944975536529910, -1.110638925478639960, 0.8300000000000022915 ) ) ; +#82862 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82861 = CARTESIAN_POINT ( 'NONE', ( 0.4264791961179740243, -0.9850687526833949992, 0.8100000000000000533 ) ) ; +#82863 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82864 = SURFACE_SIDE_STYLE ('',( #20058 ) ) ; +#82865 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56816, #87916, #80788, #96556, #81306, #41976, #27674, #33308, #72106, #73113, #2666, #49642, #40979, #41473, #2165, #64443, #19484 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.705228468942345464E-05, 5.458052432789073236E-05, 6.831271144852564059E-05, 8.155876993718065571E-05, 9.439864586050145980E-05, 0.0001069200678181052571, 0.0001193470454069942666, 0.0001314581719509183349, 0.0001436029006962719046, 0.0001558018078443743298, 0.0001685983300955028262, 0.0001819180217514510250, 0.0001963884671246620892, 0.0002119936637375566171 ), + .UNSPECIFIED. ) ; +#82866 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.900000000000000799, -0.02000000000000419845 ) ) ; +#82867 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62536, #24243, #70154 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82868 = SURFACE_SIDE_STYLE ('',( #96144 ) ) ; +#82869 = ORIENTED_EDGE ( 'NONE', *, *, #34972, .F. ) ; +#82870 = SURFACE_STYLE_FILL_AREA ( #20571 ) ; +#82871 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#82872 = VECTOR ( 'NONE', #88880, 1000.000000000000000 ) ; +#82873 = VERTEX_POINT ( 'NONE', #19674 ) ; +#82874 = EDGE_CURVE ( 'NONE', #92602, #11208, #83473, .T. ) ; +#82875 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82876 = SURFACE_STYLE_FILL_AREA ( #51751 ) ; +#82877 = VECTOR ( 'NONE', #95166, 1000.000000000000000 ) ; +#82879 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#82878 = LINE ( 'NONE', #89037, #94716 ) ; +#82880 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82881 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#82882 = FILL_AREA_STYLE ('',( #51755 ) ) ; +#82883 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69734 ), #56895 ) ; +#82884 = VECTOR ( 'NONE', #43607, 1000.000000000000000 ) ; +#82885 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.000000000000000000 ) ) ; +#82886 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#82887 = CLOSED_SHELL ( 'NONE', ( #37759, #1372, #96724, #7161, #33513, #73016 ) ) ; +#82888 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220085265, 2.499999999999999556, -0.02000000000000000042 ) ) ; +#82889 = EDGE_CURVE ( 'NONE', #20936, #43863, #36523, .T. ) ; +#82890 = ORIENTED_EDGE ( 'NONE', *, *, #92685, .T. ) ; +#82891 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#82892 = FACE_OUTER_BOUND ( 'NONE', #38889, .T. ) ; +#82893 = SURFACE_STYLE_FILL_AREA ( #68036 ) ; +#82894 = AXIS2_PLACEMENT_3D ( 'NONE', #70462, #68933, #53160 ) ; +#82895 = PRESENTATION_STYLE_ASSIGNMENT (( #84386 ) ) ; +#82896 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#82897 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82898 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#82899 = LINE ( 'NONE', #83402, #38376 ) ; +#82900 = LINE ( 'NONE', #82411, #9935 ) ; +#82901 = VECTOR ( 'NONE', #49751, 1000.000000000000000 ) ; +#82902 = SURFACE_SIDE_STYLE ('',( #42591 ) ) ; +#82903 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#82904 = FILL_AREA_STYLE ('',( #37453 ) ) ; +#82905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27672, 'distance_accuracy_value', 'NONE'); +#82906 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58458 ), #71459 ) ; +#82907 = LINE ( 'NONE', #42597, #58365 ) ; +#82908 = AXIS2_PLACEMENT_3D ( 'NONE', #1355, #86106, #63666 ) ; +#82909 = ORIENTED_EDGE ( 'NONE', *, *, #68221, .F. ) ; +#82910 = SURFACE_STYLE_FILL_AREA ( #59466 ) ; +#82911 = ORIENTED_EDGE ( 'NONE', *, *, #17682, .T. ) ; +#82912 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16135, 'distance_accuracy_value', 'NONE'); +#82913 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99354, 'distance_accuracy_value', 'NONE'); +#82914 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34025 ), #17723 ) ; +#82915 = CARTESIAN_POINT ( 'NONE', ( 1.148869891942319921, -0.9585643914498560569, 0.8299999999999999600 ) ) ; +#82916 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 9.417844000000002325, 0.8648700000000000276 ) ) ; +#82917 = SURFACE_SIDE_STYLE ('',( #65570 ) ) ; +#82918 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#82919 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#82920 = FACE_OUTER_BOUND ( 'NONE', #50181, .T. ) ; +#82921 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 15.15000000000000036, 0.000000000000000000 ) ) ; +#82922 = VERTEX_POINT ( 'NONE', #21170 ) ; +#82923 = EDGE_CURVE ( 'NONE', #88062, #4348, #50358, .T. ) ; +#82924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62940, 'distance_accuracy_value', 'NONE'); +#82925 = PRESENTATION_STYLE_ASSIGNMENT (( #68069 ) ) ; +#82926 = PRESENTATION_STYLE_ASSIGNMENT (( #5765 ) ) ; +#82927 = VECTOR ( 'NONE', #99375, 1000.000000000000000 ) ; +#82928 = VERTEX_POINT ( 'NONE', #42661 ) ; +#82929 = EDGE_CURVE ( 'NONE', #94339, #63488, #75797, .T. ) ; +#82930 = SURFACE_SIDE_STYLE ('',( #20622 ) ) ; +#82931 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#82932 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92882 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21347, #60200, #91784 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#82933 = ORIENTED_EDGE ( 'NONE', *, *, #47003, .T. ) ; +#82934 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#82935 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10965, 'distance_accuracy_value', 'NONE'); +#82936 = CIRCLE ( 'NONE', #58494, 0.009999999999999998473 ) ; +#82937 = AXIS2_PLACEMENT_3D ( 'NONE', #27927, #20738, #40852 ) ; +#82938 = CARTESIAN_POINT ( 'NONE', ( 1.592056040834880060, -1.030915998478539874, 0.8099999999999994982 ) ) ; +#82939 = EDGE_CURVE ( 'NONE', #4348, #54838, #51337, .T. ) ; +#82940 = MANIFOLD_SOLID_BREP ( 'ÊäÈë89', #50134 ) ; +#82941 = ORIENTED_EDGE ( 'NONE', *, *, #6415, .F. ) ; +#82942 = PLANE ( 'NONE', #83939 ) ; +#82943 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#82944 = CARTESIAN_POINT ( 'NONE', ( -0.5799999999567262421, 0.2999999999815372576, -1.665334536835250932E-17 ) ) ; +#82945 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20988 ), #51988 ) ; +#82946 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#82947 = PLANE ( 'NONE', #72787 ) ; +#82948 = ORIENTED_EDGE ( 'NONE', *, *, #51162, .T. ) ; +#82949 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#82950 = VECTOR ( 'NONE', #64768, 1000.000000000000000 ) ; +#82951 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74789 ), #86216 ) ; +#82952 = AXIS2_PLACEMENT_3D ( 'NONE', #81399, #34925, #50757 ) ; +#82953 = EDGE_LOOP ( 'NONE', ( #23655, #98799 ) ) ; +#82955 = VERTEX_POINT ( 'NONE', #11919 ) ; +#82954 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#82956 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#82957 = EDGE_CURVE ( 'NONE', #67213, #84706, #11421, .T. ) ; +#82958 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#82959 = CARTESIAN_POINT ( 'NONE', ( -1.321337043985290061, -1.462480703074420019, 0.8100000000000000533 ) ) ; +#82960 = SURFACE_STYLE_FILL_AREA ( #42162 ) ; +#82961 = FACE_OUTER_BOUND ( 'NONE', #2625, .T. ) ; +#82962 = STYLED_ITEM ( 'NONE', ( #24870 ), #153 ) ; +#82963 = ORIENTED_EDGE ( 'NONE', *, *, #36389, .F. ) ; +#82964 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#82965 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#82966 = ORIENTED_EDGE ( 'NONE', *, *, #10861, .F. ) ; +#82967 = CARTESIAN_POINT ( 'NONE', ( 1.309875304108520044, -1.500691070757680157, 0.8299999999999999600 ) ) ; +#82968 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#82969 = SURFACE_STYLE_USAGE ( .BOTH. , #37012 ) ; +#82970 = VERTEX_POINT ( 'NONE', #60015 ) ; +#82971 = VECTOR ( 'NONE', #34931, 1000.000000000000000 ) ; +#82972 = VERTEX_POINT ( 'NONE', #91123 ) ; +#82973 = EDGE_CURVE ( 'NONE', #34634, #94036, #81495, .T. ) ; +#82975 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999994005, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#82974 = PLANE ( 'NONE', #60991 ) ; +#82976 = VECTOR ( 'NONE', #21691, 1000.000000000000000 ) ; +#82977 = LINE ( 'NONE', #5317, #40888 ) ; +#82978 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89546 ), #43904 ) ; +#82979 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 4.984284999999999854, 0.8991599999999999593 ) ) ; +#82980 = ORIENTED_EDGE ( 'NONE', *, *, #98186, .T. ) ; +#82981 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#82982 = VERTEX_POINT ( 'NONE', #4346 ) ; +#82984 = PRESENTATION_STYLE_ASSIGNMENT (( #58040 ) ) ; +#82983 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#82985 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#82986 = SURFACE_SIDE_STYLE ('',( #12956 ) ) ; +#82987 = VECTOR ( 'NONE', #8343, 1000.000000000000000 ) ; +#82988 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#82990 = ADVANCED_FACE ( 'NONE', ( #35524 ), #66626, .F. ) ; +#82989 = AXIS2_PLACEMENT_3D ( 'NONE', #39127, #48825, #25356 ) ; +#82991 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666647068, 0.09999999999999939493, 3.495651678170021751E-76 ) ) ; +#82992 = PLANE ( 'NONE', #74790 ) ; +#82993 = SURFACE_STYLE_FILL_AREA ( #68645 ) ; +#82994 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.299999999999999822, 0.000000000000000000 ) ) ; +#82995 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63421 ), #97602 ) ; +#82996 = PRESENTATION_STYLE_ASSIGNMENT (( #69648 ) ) ; +#82997 = EDGE_LOOP ( 'NONE', ( #44778, #18750, #32783, #28746 ) ) ; +#82998 = EDGE_CURVE ( 'NONE', #25243, #46252, #30835, .T. ) ; +#82999 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#83000 = LINE ( 'NONE', #44177, #3616 ) ; +#83001 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27638 ) ) ; +#83002 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83004 = MANIFOLD_SOLID_BREP ( 'ÊäÈë125', #53519 ) ; +#83003 = LINE ( 'NONE', #12463, #59406 ) ; +#83005 = STYLED_ITEM ( 'NONE', ( #32316 ), #84925 ) ; +#83006 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98277 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93154, #99728, #46713 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83008 = SURFACE_STYLE_FILL_AREA ( #28382 ) ; +#83009 = EDGE_CURVE ( 'NONE', #2215, #85310, #69090, .T. ) ; +#83011 = ORIENTED_EDGE ( 'NONE', *, *, #8029, .F. ) ; +#83010 = STYLED_ITEM ( 'NONE', ( #11376 ), #55842 ) ; +#83012 = VECTOR ( 'NONE', #17858, 1000.000000000000000 ) ; +#83013 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#83014 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83015 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83016 = PRESENTATION_STYLE_ASSIGNMENT (( #20717 ) ) ; +#83017 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999901329, 0.4700000000088402907, 0.6499230723514386465 ) ) ; +#83018 = SURFACE_SIDE_STYLE ('',( #6340 ) ) ; +#83019 = STYLED_ITEM ( 'NONE', ( #93372 ), #80004 ) ; +#83020 = PRESENTATION_STYLE_ASSIGNMENT (( #43689 ) ) ; +#83021 = PLANE ( 'NONE', #85917 ) ; +#83022 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#83023 = CARTESIAN_POINT ( 'NONE', ( 6.876949127034753140, 10.29465662703633555, 0.8648700000000000276 ) ) ; +#83024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45427 ), #91104 ) ; +#83025 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83026 = FILL_AREA_STYLE ('',( #28889 ) ) ; +#83027 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#83028 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83029 = VECTOR ( 'NONE', #71098, 1000.000000000000114 ) ; +#83030 = FILL_AREA_STYLE ('',( #71341 ) ) ; +#83031 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84443 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18559, #58925, #50261 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83032 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#83033 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83034 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40891, 'distance_accuracy_value', 'NONE'); +#83035 = LINE ( 'NONE', #52399, #38909 ) ; +#83036 = FACE_OUTER_BOUND ( 'NONE', #35280, .T. ) ; +#83037 = SURFACE_STYLE_USAGE ( .BOTH. , #74374 ) ; +#83038 = ORIENTED_EDGE ( 'NONE', *, *, #49495, .T. ) ; +#83039 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#83040 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48272, 'distance_accuracy_value', 'NONE'); +#83041 = FACE_OUTER_BOUND ( 'NONE', #4698, .T. ) ; +#83042 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86724, 'distance_accuracy_value', 'NONE'); +#83043 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8648700000000000276 ) ) ; +#83044 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 15.15000000000000036, 0.000000000000000000 ) ) ; +#83045 = ADVANCED_FACE ( 'NONE', ( #39013 ), #76288, .F. ) ; +#83046 = EDGE_CURVE ( 'NONE', #97279, #61391, #9794, .T. ) ; +#83047 = PLANE ( 'NONE', #59840 ) ; +#83048 = VERTEX_POINT ( 'NONE', #94622 ) ; +#83049 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83050 = EDGE_LOOP ( 'NONE', ( #46629, #76622, #30120, #93947 ) ) ; +#83051 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83052 = VECTOR ( 'NONE', #10996, 1000.000000000000000 ) ; +#83053 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#83054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93093, 'distance_accuracy_value', 'NONE'); +#83055 = SURFACE_SIDE_STYLE ('',( #51433 ) ) ; +#83056 = EDGE_CURVE ( 'NONE', #91365, #29928, #70648, .T. ) ; +#83057 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.000000000000000000 ) ) ; +#83058 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 11.30020599999999931, 0.8648700000000000276 ) ) ; +#83059 = EDGE_CURVE ( 'NONE', #85854, #67839, #32370, .T. ) ; +#83060 = VERTEX_POINT ( 'NONE', #697 ) ; +#83061 = EDGE_LOOP ( 'NONE', ( #14321, #50697, #47919, #44567 ) ) ; +#83062 = ADVANCED_FACE ( 'NONE', ( #25245 ), #78816, .T. ) ; +#83063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83064 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47185 ) ) ; +#83065 = ORIENTED_EDGE ( 'NONE', *, *, #10932, .T. ) ; +#83066 = CARTESIAN_POINT ( 'NONE', ( 0.2416947311349459948, -1.083527867505859943, 0.8299999999999996270 ) ) ; +#83067 = STYLED_ITEM ( 'NONE', ( #13553 ), #75195 ) ; +#83068 = EDGE_CURVE ( 'NONE', #97600, #68615, #1201, .T. ) ; +#83069 = SURFACE_SIDE_STYLE ('',( #89222 ) ) ; +#83070 = SURFACE_STYLE_FILL_AREA ( #83572 ) ; +#83071 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83072 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83073 = STYLED_ITEM ( 'NONE', ( #5807 ), #92823 ) ; +#83074 = DIRECTION ( 'NONE', ( -0.7071075504167438908, -0.7071060119555143686, 0.000000000000000000 ) ) ; +#83076 = VERTEX_POINT ( 'NONE', #48706 ) ; +#83075 = ORIENTED_EDGE ( 'NONE', *, *, #98752, .F. ) ; +#83077 = ORIENTED_EDGE ( 'NONE', *, *, #100187, .T. ) ; +#83078 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4840 ) ) ; +#83079 = ORIENTED_EDGE ( 'NONE', *, *, #18419, .T. ) ; +#83080 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#83081 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83082 = EDGE_CURVE ( 'NONE', #85774, #7779, #49725, .T. ) ; +#83083 = SURFACE_STYLE_USAGE ( .BOTH. , #51952 ) ; +#83085 = CARTESIAN_POINT ( 'NONE', ( -2.300000000000000266, -3.123820061220085265, 0.000000000000000000 ) ) ; +#83084 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83086 = VECTOR ( 'NONE', #69683, 1000.000000000000000 ) ; +#83087 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #100858 ), #16140 ) ; +#83088 = EDGE_CURVE ( 'NONE', #65740, #2685, #41543, .T. ) ; +#83089 = FILL_AREA_STYLE_COLOUR ( '', #88137 ) ; +#83090 = CARTESIAN_POINT ( 'NONE', ( -1.319753185035670073, -0.9379159637996590249, 0.8299999999999999600 ) ) ; +#83091 = ORIENTED_EDGE ( 'NONE', *, *, #69671, .T. ) ; +#83092 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#83093 = ORIENTED_EDGE ( 'NONE', *, *, #63186, .T. ) ; +#83094 = ORIENTED_EDGE ( 'NONE', *, *, #22860, .F. ) ; +#83095 = CARTESIAN_POINT ( 'NONE', ( 0.9819563994042010968, -1.066576130479129914, 0.8299999999999999600 ) ) ; +#83096 = ADVANCED_FACE ( 'NONE', ( #48199 ), #18539, .T. ) ; +#83097 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83098 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7993 ), #76588 ) ; +#83099 = CARTESIAN_POINT ( 'NONE', ( 1.850801046367029912, -1.212495751768599916, 0.8300000000000004041 ) ) ; +#83100 = EDGE_CURVE ( 'NONE', #80080, #41651, #68465, .T. ) ; +#83102 = VERTEX_POINT ( 'NONE', #4720 ) ; +#83101 = SURFACE_STYLE_USAGE ( .BOTH. , #26978 ) ; +#83104 = STYLED_ITEM ( 'NONE', ( #41006 ), #42441 ) ; +#83103 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#83105 = FILL_AREA_STYLE_COLOUR ( '', #32385 ) ; +#83106 = FACE_OUTER_BOUND ( 'NONE', #19118, .T. ) ; +#83107 = SURFACE_STYLE_USAGE ( .BOTH. , #13567 ) ; +#83108 = ORIENTED_EDGE ( 'NONE', *, *, #41510, .F. ) ; +#83109 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83110 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83111 = ORIENTED_EDGE ( 'NONE', *, *, #88361, .F. ) ; +#83112 = VERTEX_POINT ( 'NONE', #66020 ) ; +#83115 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83114 = CARTESIAN_POINT ( 'NONE', ( 0.5377516545130740511, -1.015240267636180027, 0.8299999999999992939 ) ) ; +#83113 = PRODUCT_DEFINITION ( 'δ֪', '', #25803, #89189 ) ; +#83116 = MANIFOLD_SOLID_BREP ( 'ÊäÈë2', #33793 ) ; +#83117 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999997780, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#83118 = VECTOR ( 'NONE', #91905, 1000.000000000000000 ) ; +#83119 = SURFACE_STYLE_USAGE ( .BOTH. , #91264 ) ; +#83120 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#83121 = ORIENTED_EDGE ( 'NONE', *, *, #22730, .F. ) ; +#83122 = EDGE_CURVE ( 'NONE', #33508, #82955, #69499, .T. ) ; +#83123 = LINE ( 'NONE', #5458, #23546 ) ; +#83124 = ORIENTED_EDGE ( 'NONE', *, *, #90086, .F. ) ; +#83125 = PRESENTATION_STYLE_ASSIGNMENT (( #50507 ) ) ; +#83126 = CARTESIAN_POINT ( 'NONE', ( -0.03082045455219830504, -0.9939892240680031632, 0.8299999999999999600 ) ) ; +#83127 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83128 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#83129 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8648700000000000276 ) ) ; +#83130 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86398 ), #92252 ) ; +#83131 = FACE_OUTER_BOUND ( 'NONE', #12281, .T. ) ; +#83132 = FILL_AREA_STYLE ('',( #44293 ) ) ; +#83133 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.1499999999999999944, -0.02000000000000000042 ) ) ; +#83134 = FILL_AREA_STYLE ('',( #13095 ) ) ; +#83135 = EDGE_CURVE ( 'NONE', #51917, #3989, #81890, .T. ) ; +#83136 = VERTEX_POINT ( 'NONE', #58399 ) ; +#83137 = SURFACE_STYLE_FILL_AREA ( #61677 ) ; +#83138 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83139 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.1600000000000000033, 1.129999999999999893 ) ) ; +#83140 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37518 ), #32638 ) ; +#83141 = CYLINDRICAL_SURFACE ( 'NONE', #16402, 0.2000000000000000111 ) ; +#83142 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83143 = EDGE_CURVE ( 'NONE', #55224, #85953, #14084, .T. ) ; +#83144 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#83145 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64932 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33115, #47421, #86731 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83146 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8991599999999999593 ) ) ; +#83147 = ADVANCED_FACE ( 'NONE', ( #50727 ), #73197, .T. ) ; +#83148 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.01085786437626907325, 0.2500000000000000000 ) ) ; +#83149 = AXIS2_PLACEMENT_3D ( 'NONE', #23446, #30558, #77558 ) ; +#83150 = AXIS2_PLACEMENT_3D ( 'NONE', #89330, #2550, #41866 ) ; +#83151 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83152 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92654, 'distance_accuracy_value', 'NONE'); +#83153 = VECTOR ( 'NONE', #75942, 1000.000000000000000 ) ; +#83154 = ORIENTED_EDGE ( 'NONE', *, *, #31819, .F. ) ; +#83155 = CARTESIAN_POINT ( 'NONE', ( -0.007881824293594717062, -1.487781485457422059, 0.8099999999995173283 ) ) ; +#83156 = LINE ( 'NONE', #13624, #28055 ) ; +#83157 = ORIENTED_EDGE ( 'NONE', *, *, #8251, .F. ) ; +#83158 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#83159 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#83160 = VECTOR ( 'NONE', #41641, 1000.000000000000000 ) ; +#83161 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#83162 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999999956, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#83163 = SURFACE_SIDE_STYLE ('',( #44321 ) ) ; +#83164 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23820, 'distance_accuracy_value', 'NONE'); +#83165 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35881 ), #92867 ) ; +#83166 = LINE ( 'NONE', #98391, #55762 ) ; +#83167 = VECTOR ( 'NONE', #46432, 1000.000000000000000 ) ; +#83168 = SURFACE_STYLE_FILL_AREA ( #66823 ) ; +#83169 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.266666666666653285, 0.000000000000000000 ) ) ; +#83170 = EDGE_CURVE ( 'NONE', #57188, #81120, #3233, .T. ) ; +#83171 = EDGE_CURVE ( 'NONE', #57887, #81673, #57905, .T. ) ; +#83172 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, 4.495825008573221561E-17, 0.8499999999999999778 ) ) ; +#83173 = VECTOR ( 'NONE', #34046, 1000.000000000000000 ) ; +#83174 = ORIENTED_EDGE ( 'NONE', *, *, #29644, .T. ) ; +#83175 = STYLED_ITEM ( 'NONE', ( #11963 ), #1633 ) ; +#83176 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83177 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83178 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83179 = VECTOR ( 'NONE', #27907, 1000.000000000000000 ) ; +#83180 = FILL_AREA_STYLE ('',( #29045 ) ) ; +#83181 = MANIFOLD_SOLID_BREP ( 'ÊäÈë62', #2879 ) ; +#83182 = FILL_AREA_STYLE_COLOUR ( '', #60215 ) ; +#83183 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22236, 'distance_accuracy_value', 'NONE'); +#83184 = SURFACE_SIDE_STYLE ('',( #98402 ) ) ; +#83185 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33961, 'distance_accuracy_value', 'NONE'); +#83186 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83187 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2850000000000000311, 0.1400000000000000133 ) ) ; +#83188 = EDGE_CURVE ( 'NONE', #85932, #7186, #8524, .T. ) ; +#83189 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999986226, 0.1400000000000000133 ) ) ; +#83190 = ORIENTED_EDGE ( 'NONE', *, *, #77180, .T. ) ; +#83191 = ORIENTED_EDGE ( 'NONE', *, *, #17634, .F. ) ; +#83192 = EDGE_CURVE ( 'NONE', #42884, #51226, #13309, .T. ) ; +#83193 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45703 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37742, #15726, #39746 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83194 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43850, 'distance_accuracy_value', 'NONE'); +#83195 = ORIENTED_EDGE ( 'NONE', *, *, #79423, .T. ) ; +#83196 = FILL_AREA_STYLE_COLOUR ( '', #52812 ) ; +#83197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83198 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.000000000000000000 ) ) ; +#83199 = AXIS2_PLACEMENT_3D ( 'NONE', #40219, #18191, #9485 ) ; +#83200 = FILL_AREA_STYLE_COLOUR ( '', #20305 ) ; +#83201 = CARTESIAN_POINT ( 'NONE', ( -0.4123911155665859751, -0.9468660869752939524, 0.8299999999999999600 ) ) ; +#83202 = FILL_AREA_STYLE_COLOUR ( '', #12124 ) ; +#83204 = EDGE_LOOP ( 'NONE', ( #68491, #46212, #44184, #63409, #71655, #3045 ) ) ; +#83203 = EDGE_LOOP ( 'NONE', ( #99293, #98935, #87610, #49453 ) ) ; +#83205 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3242 ) ) ; +#83206 = VERTEX_POINT ( 'NONE', #9047 ) ; +#83208 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83207 = SURFACE_STYLE_FILL_AREA ( #12159 ) ; +#83209 = ORIENTED_EDGE ( 'NONE', *, *, #17230, .F. ) ; +#83210 = ORIENTED_EDGE ( 'NONE', *, *, #48814, .F. ) ; +#83211 = FACE_OUTER_BOUND ( 'NONE', #31151, .T. ) ; +#83212 = EDGE_CURVE ( 'NONE', #3678, #48043, #38269, .T. ) ; +#83213 = SURFACE_STYLE_FILL_AREA ( #51081 ) ; +#83214 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29886 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74388, #41249, #42737 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83215 = SURFACE_STYLE_FILL_AREA ( #53073 ) ; +#83216 = ORIENTED_EDGE ( 'NONE', *, *, #50193, .F. ) ; +#83217 = VERTEX_POINT ( 'NONE', #16754 ) ; +#83218 = ORIENTED_EDGE ( 'NONE', *, *, #39035, .F. ) ; +#83219 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#83220 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220065281, 0.4999999999999998890, 0.000000000000000000 ) ) ; +#83221 = VECTOR ( 'NONE', #3366, 1000.000000000000000 ) ; +#83222 = AXIS2_PLACEMENT_3D ( 'NONE', #15095, #40664, #16121 ) ; +#83223 = EDGE_CURVE ( 'NONE', #6286, #25944, #5688, .T. ) ; +#83224 = AXIS2_PLACEMENT_3D ( 'NONE', #37796, #30112, #100447 ) ; +#83225 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83226 = ADVANCED_FACE ( 'NONE', ( #71421 ), #93344, .T. ) ; +#83228 = ORIENTED_EDGE ( 'NONE', *, *, #49063, .F. ) ; +#83227 = LINE ( 'NONE', #27608, #73890 ) ; +#83229 = VECTOR ( 'NONE', #56778, 1000.000000000000000 ) ; +#83230 = LINE ( 'NONE', #6543, #54715 ) ; +#83231 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8100000000000000533 ) ) ; +#83232 = ORIENTED_EDGE ( 'NONE', *, *, #48587, .T. ) ; +#83233 = SURFACE_STYLE_FILL_AREA ( #100417 ) ; +#83234 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83235 = ORIENTED_EDGE ( 'NONE', *, *, #40898, .F. ) ; +#83236 = ORIENTED_EDGE ( 'NONE', *, *, #35939, .F. ) ; +#83237 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87161 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71135, #64490, #10251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83238 = PRESENTATION_STYLE_ASSIGNMENT (( #52103 ) ) ; +#83239 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83240 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7478 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44308, #67791, #35203 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83241 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83242 = AXIS2_PLACEMENT_3D ( 'NONE', #78373, #45674, #93133 ) ; +#83243 = SURFACE_STYLE_FILL_AREA ( #90893 ) ; +#83244 = DIRECTION ( 'NONE', ( -0.9999999999319444388, -1.166666666623709853E-05, 0.000000000000000000 ) ) ; +#83245 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#83246 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83247 = PRESENTATION_STYLE_ASSIGNMENT (( #52111 ) ) ; +#83248 = AXIS2_PLACEMENT_3D ( 'NONE', #90139, #44176, #83505 ) ; +#83249 = ORIENTED_EDGE ( 'NONE', *, *, #47536, .T. ) ; +#83250 = EDGE_CURVE ( 'NONE', #81543, #16868, #69359, .T. ) ; +#83251 = VECTOR ( 'NONE', #76331, 1000.000000000000000 ) ; +#83252 = CARTESIAN_POINT ( 'NONE', ( -1.125815218778140059, -1.515241174392790047, 0.8299999999999999600 ) ) ; +#83253 = ORIENTED_EDGE ( 'NONE', *, *, #6374, .T. ) ; +#83254 = VECTOR ( 'NONE', #69742, 1000.000000000000000 ) ; +#83255 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83256 = AXIS2_PLACEMENT_3D ( 'NONE', #84382, #82891, #44071 ) ; +#83257 = FILL_AREA_STYLE_COLOUR ( '', #50019 ) ; +#83258 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#83259 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -1.633333333333333304, 0.000000000000000000 ) ) ; +#83260 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8991599999999999593 ) ) ; +#83262 = ADVANCED_FACE ( 'NONE', ( #70390 ), #62773, .F. ) ; +#83261 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83263 = FILL_AREA_STYLE ('',( #11203 ) ) ; +#83264 = SURFACE_STYLE_USAGE ( .BOTH. , #22464 ) ; +#83265 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83266 = EDGE_CURVE ( 'NONE', #6006, #24413, #17774, .T. ) ; +#83267 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #97516, #27624, #17897, #56768 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#83268 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.28250199999999914, 0.8991599999999999593 ) ) ; +#83269 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 10.26637200000000050, 0.8648700000000000276 ) ) ; +#83270 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.000000000000000000 ) ) ; +#83271 = EDGE_CURVE ( 'NONE', #454, #61349, #69575, .T. ) ; +#83272 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35990 ) ) ; +#83274 = EDGE_CURVE ( 'NONE', #39862, #90342, #87233, .T. ) ; +#83273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61976, 'distance_accuracy_value', 'NONE'); +#83275 = ORIENTED_EDGE ( 'NONE', *, *, #31348, .F. ) ; +#83276 = MANIFOLD_SOLID_BREP ( 'ÊäÈë3', #1171 ) ; +#83277 = SURFACE_STYLE_USAGE ( .BOTH. , #60322 ) ; +#83278 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83279 = CARTESIAN_POINT ( 'NONE', ( 0.4634109025151903483, -1.114344799413643061, 0.8100000000000001643 ) ) ; +#83280 = FILL_AREA_STYLE_COLOUR ( '', #9402 ) ; +#83281 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2749999999999999667, 0.1399999999999999856 ) ) ; +#83282 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44189 ) ) ; +#83283 = LINE ( 'NONE', #36816, #19823 ) ; +#83284 = SURFACE_STYLE_FILL_AREA ( #52646 ) ; +#83285 = FILL_AREA_STYLE ('',( #52155 ) ) ; +#83287 = EDGE_CURVE ( 'NONE', #53575, #39936, #11558, .T. ) ; +#83286 = PRODUCT ( 'ESP32-S3-MINI-1U_V1_3D', 'ESP32-S3-MINI-1U_V1_3D', '', ( #37246 ) ) ; +#83288 = EDGE_CURVE ( 'NONE', #33538, #22417, #95880, .T. ) ; +#83289 = VECTOR ( 'NONE', #21685, 1000.000000000000000 ) ; +#83290 = AXIS2_PLACEMENT_3D ( 'NONE', #36068, #75845, #74851 ) ; +#83291 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#83292 = VERTEX_POINT ( 'NONE', #18269 ) ; +#83293 = SURFACE_STYLE_USAGE ( .BOTH. , #29165 ) ; +#83294 = ORIENTED_EDGE ( 'NONE', *, *, #13141, .T. ) ; +#83295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83296 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39500, 'distance_accuracy_value', 'NONE'); +#83297 = VECTOR ( 'NONE', #56264, 1000.000000000000000 ) ; +#83298 = EDGE_CURVE ( 'NONE', #24186, #60257, #88260, .T. ) ; +#83299 = EDGE_CURVE ( 'NONE', #100385, #1733, #73942, .T. ) ; +#83300 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8648700000000000276 ) ) ; +#83301 = CARTESIAN_POINT ( 'NONE', ( -0.1830714119375710103, -0.9850088450568520448, 0.8100000000000000533 ) ) ; +#83302 = DIRECTION ( 'NONE', ( -0.3516809254569071008, 0.000000000000000000, 0.9361199317767854300 ) ) ; +#83303 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83304 = LINE ( 'NONE', #13255, #92483 ) ; +#83305 = FILL_AREA_STYLE ('',( #35361 ) ) ; +#83306 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83307 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#83308 = VERTEX_POINT ( 'NONE', #66282 ) ; +#83309 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #73474, #87258, #63317, #17803 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#83310 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83311 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9472 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99305, #37126, #6404 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83312 = VERTEX_POINT ( 'NONE', #97380 ) ; +#83313 = SURFACE_STYLE_USAGE ( .BOTH. , #68456 ) ; +#83314 = EDGE_CURVE ( 'NONE', #92966, #77034, #9549, .T. ) ; +#83315 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83316 = ORIENTED_EDGE ( 'NONE', *, *, #28044, .T. ) ; +#83317 = ADVANCED_FACE ( 'NONE', ( #60159 ), #20297, .T. ) ; +#83318 = LINE ( 'NONE', #42990, #38183 ) ; +#83319 = FILL_AREA_STYLE_COLOUR ( '', #574 ) ; +#83320 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84960 ) ) ; +#83321 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83322 = AXIS2_PLACEMENT_3D ( 'NONE', #14392, #13353, #61436 ) ; +#83324 = VERTEX_POINT ( 'NONE', #28968 ) ; +#83323 = EDGE_LOOP ( 'NONE', ( #55614, #2301, #90385, #44664 ) ) ; +#83325 = ORIENTED_EDGE ( 'NONE', *, *, #2334, .T. ) ; +#83327 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#83326 = LINE ( 'NONE', #66983, #83339 ) ; +#83328 = ORIENTED_EDGE ( 'NONE', *, *, #52617, .T. ) ; +#83329 = ORIENTED_EDGE ( 'NONE', *, *, #70601, .T. ) ; +#83330 = FACE_OUTER_BOUND ( 'NONE', #98437, .T. ) ; +#83331 = CARTESIAN_POINT ( 'NONE', ( -0.5594799075883629680, -1.188256883098049999, 0.8299999999999999600 ) ) ; +#83332 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83334 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83333 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83335 = ORIENTED_EDGE ( 'NONE', *, *, #22695, .F. ) ; +#83336 = VERTEX_POINT ( 'NONE', #13068 ) ; +#83337 = VECTOR ( 'NONE', #32601, 1000.000000000000000 ) ; +#83338 = ORIENTED_EDGE ( 'NONE', *, *, #54594, .F. ) ; +#83339 = VECTOR ( 'NONE', #21031, 1000.000000000000000 ) ; +#83340 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83341 = EDGE_CURVE ( 'NONE', #81623, #34706, #83613, .T. ) ; +#83342 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83344 = ORIENTED_EDGE ( 'NONE', *, *, #39284, .F. ) ; +#83343 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83345 = LINE ( 'NONE', #11420, #1776 ) ; +#83346 = SURFACE_SIDE_STYLE ('',( #66014 ) ) ; +#83347 = SURFACE_STYLE_USAGE ( .BOTH. , #91495 ) ; +#83348 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#83349 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#83350 = ORIENTED_EDGE ( 'NONE', *, *, #54520, .T. ) ; +#83352 = EDGE_CURVE ( 'NONE', #86804, #41417, #43783, .T. ) ; +#83351 = SURFACE_STYLE_USAGE ( .BOTH. , #43520 ) ; +#83353 = FACE_OUTER_BOUND ( 'NONE', #81447, .T. ) ; +#83354 = ORIENTED_EDGE ( 'NONE', *, *, #5871, .T. ) ; +#83355 = CARTESIAN_POINT ( 'NONE', ( 0.2708752286681453403, -1.369498746218061003, 0.8100000000000002753 ) ) ; +#83356 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83357 = LINE ( 'NONE', #91009, #42752 ) ; +#83358 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83359 = SURFACE_STYLE_USAGE ( .BOTH. , #21073 ) ; +#83360 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83362 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4749999999999999778, -0.2500000000000000000 ) ) ; +#83361 = FILL_AREA_STYLE ('',( #50244 ) ) ; +#83363 = LINE ( 'NONE', #98575, #44003 ) ; +#83364 = EDGE_CURVE ( 'NONE', #16395, #62901, #90760, .T. ) ; +#83365 = ORIENTED_EDGE ( 'NONE', *, *, #3011, .F. ) ; +#83366 = AXIS2_PLACEMENT_3D ( 'NONE', #51460, #44245, #59131 ) ; +#83367 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83368 = VECTOR ( 'NONE', #82501, 1000.000000000000000 ) ; +#83369 = VECTOR ( 'NONE', #66920, 1000.000000000000114 ) ; +#83370 = CARTESIAN_POINT ( 'NONE', ( 1.416650401028419992, -1.249140550102370018, 0.8300000000000022915 ) ) ; +#83372 = SURFACE_SIDE_STYLE ('',( #92012 ) ) ; +#83371 = CARTESIAN_POINT ( 'NONE', ( 0.4587323827270540222, -1.026347246440100003, 0.8100000000000000533 ) ) ; +#83373 = DIRECTION ( 'NONE', ( -0.000000000000000000, 5.551115123125780237E-17, 1.000000000000000000 ) ) ; +#83374 = PRESENTATION_STYLE_ASSIGNMENT (( #91021 ) ) ; +#83376 = EDGE_CURVE ( 'NONE', #27038, #79941, #75430, .T. ) ; +#83375 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83377 = VECTOR ( 'NONE', #48325, 1000.000000000000000 ) ; +#83378 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99591 ) ) ; +#83379 = SURFACE_STYLE_USAGE ( .BOTH. , #82868 ) ; +#83380 = ORIENTED_EDGE ( 'NONE', *, *, #29136, .T. ) ; +#83381 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#83382 = LINE ( 'NONE', #51745, #98389 ) ; +#83383 = PLANE ( 'NONE', #25598 ) ; +#83384 = ORIENTED_EDGE ( 'NONE', *, *, #26579, .F. ) ; +#83385 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42096 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74101, #35327, #66924 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83386 = SURFACE_SIDE_STYLE ('',( #21094 ) ) ; +#83387 = VECTOR ( 'NONE', #11008, 1000.000000000000000 ) ; +#83389 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#83388 = SURFACE_STYLE_FILL_AREA ( #5216 ) ; +#83390 = PRESENTATION_STYLE_ASSIGNMENT (( #29257 ) ) ; +#83391 = EDGE_CURVE ( 'NONE', #71812, #28814, #5438, .T. ) ; +#83392 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88278 ) ) ; +#83393 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83394 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83395 = LINE ( 'NONE', #61926, #429 ) ; +#83396 = EDGE_CURVE ( 'NONE', #94737, #10764, #44765, .T. ) ; +#83397 = ORIENTED_EDGE ( 'NONE', *, *, #64595, .T. ) ; +#83398 = PRESENTATION_STYLE_ASSIGNMENT (( #52762 ) ) ; +#83399 = PLANE ( 'NONE', #95449 ) ; +#83400 = FILL_AREA_STYLE_COLOUR ( '', #49307 ) ; +#83401 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83402 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, 0.000000000000000000 ) ) ; +#83403 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23058 ), #45813 ) ; +#83404 = SURFACE_SIDE_STYLE ('',( #28277 ) ) ; +#83405 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83406 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83407 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#83408 = VECTOR ( 'NONE', #34885, 1000.000000000000000 ) ; +#83409 = EDGE_CURVE ( 'NONE', #66284, #57896, #90249, .T. ) ; +#83410 = SURFACE_STYLE_FILL_AREA ( #19600 ) ; +#83411 = EDGE_CURVE ( 'NONE', #54776, #83836, #74946, .T. ) ; +#83412 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83413 = ORIENTED_EDGE ( 'NONE', *, *, #94841, .F. ) ; +#83414 = ORIENTED_EDGE ( 'NONE', *, *, #88770, .T. ) ; +#83415 = EDGE_CURVE ( 'NONE', #54228, #1768, #99333, .T. ) ; +#83416 = EDGE_CURVE ( 'NONE', #70802, #64000, #21808, .T. ) ; +#83417 = CARTESIAN_POINT ( 'NONE', ( 1.070765459575029999, -1.007957212727089935, 0.8299999999999999600 ) ) ; +#83418 = PLANE ( 'NONE', #25124 ) ; +#83419 = FILL_AREA_STYLE ('',( #52289 ) ) ; +#83420 = CARTESIAN_POINT ( 'NONE', ( -1.063637804261009956, -1.506193478032149979, 0.8299999999999981837 ) ) ; +#83421 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83422 = CARTESIAN_POINT ( 'NONE', ( 1.750951194234720010, -0.9053603395923379704, 0.8299999999999999600 ) ) ; +#83423 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.676179938779915002, 0.000000000000000000 ) ) ; +#83424 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8648700000000000276 ) ) ; +#83425 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000006176, -0.1499999999999999944 ) ) ; +#83426 = EDGE_LOOP ( 'NONE', ( #73140, #89000, #62615, #88866 ) ) ; +#83427 = SURFACE_SIDE_STYLE ('',( #29297 ) ) ; +#83428 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, 0.2500000000000000000 ) ) ; +#83429 = EDGE_CURVE ( 'NONE', #34797, #84331, #87532, .T. ) ; +#83430 = VECTOR ( 'NONE', #77516, 1000.000000000000000 ) ; +#83431 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83432 = VERTEX_POINT ( 'NONE', #6431 ) ; +#83433 = PRESENTATION_STYLE_ASSIGNMENT (( #5266 ) ) ; +#83434 = PRESENTATION_STYLE_ASSIGNMENT (( #52791 ) ) ; +#83435 = EDGE_CURVE ( 'NONE', #63990, #76877, #4957, .T. ) ; +#83436 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#83437 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#83438 = SURFACE_STYLE_USAGE ( .BOTH. , #36970 ) ; +#83439 = FACE_OUTER_BOUND ( 'NONE', #7705, .T. ) ; +#83440 = VERTEX_POINT ( 'NONE', #68751 ) ; +#83441 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83442 = FACE_OUTER_BOUND ( 'NONE', #83050, .T. ) ; +#83443 = STYLED_ITEM ( 'NONE', ( #68411 ), #8573 ) ; +#83444 = LINE ( 'NONE', #53795, #21516 ) ; +#83445 = LINE ( 'NONE', #12401, #82884 ) ; +#83446 = MANIFOLD_SOLID_BREP ( 'ÊäÈë126', #61486 ) ; +#83447 = ORIENTED_EDGE ( 'NONE', *, *, #49914, .F. ) ; +#83448 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83449 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8099999999998962474 ) ) ; +#83450 = VECTOR ( 'NONE', #49018, 1000.000000000000000 ) ; +#83451 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.9000000000000014655, 0.000000000000000000 ) ) ; +#83452 = ORIENTED_EDGE ( 'NONE', *, *, #26593, .T. ) ; +#83453 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83454 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93168 ), #21776 ) ; +#83455 = ORIENTED_EDGE ( 'NONE', *, *, #5846, .T. ) ; +#83457 = EDGE_LOOP ( 'NONE', ( #53693, #5180, #32871, #49670 ) ) ; +#83456 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#83458 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21299, 'distance_accuracy_value', 'NONE'); +#83459 = FILL_AREA_STYLE_COLOUR ( '', #29506 ) ; +#83461 = CARTESIAN_POINT ( 'NONE', ( -1.390280071815130025, -1.351356007592219965, 0.8299999999999999600 ) ) ; +#83460 = LINE ( 'NONE', #51824, #54207 ) ; +#83462 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83463 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83464 = STYLED_ITEM ( 'NONE', ( #91077 ), #52565 ) ; +#83465 = ORIENTED_EDGE ( 'NONE', *, *, #68016, .F. ) ; +#83467 = EDGE_CURVE ( 'NONE', #50947, #21301, #99795, .T. ) ; +#83466 = SURFACE_STYLE_USAGE ( .BOTH. , #60507 ) ; +#83468 = FILL_AREA_STYLE_COLOUR ( '', #36915 ) ; +#83469 = EDGE_LOOP ( 'NONE', ( #55795, #19520, #91734, #23453 ) ) ; +#83470 = CARTESIAN_POINT ( 'NONE', ( -4.720018080210465332E-17, 0.2500000001077752887, -1.665334536835250932E-17 ) ) ; +#83471 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83472 = FILL_AREA_STYLE ('',( #69089 ) ) ; +#83473 = LINE ( 'NONE', #43634, #30281 ) ; +#83474 = AXIS2_PLACEMENT_3D ( 'NONE', #21109, #83895, #99610 ) ; +#83475 = EDGE_LOOP ( 'NONE', ( #72050, #56644, #83325, #55074 ) ) ; +#83477 = SURFACE_STYLE_USAGE ( .BOTH. , #52344 ) ; +#83476 = CARTESIAN_POINT ( 'NONE', ( 1.693812380665639994, -1.164588072778879990, 0.8099999999999998312 ) ) ; +#83478 = ORIENTED_EDGE ( 'NONE', *, *, #1118, .F. ) ; +#83479 = VECTOR ( 'NONE', #54, 1000.000000000000000 ) ; +#83481 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83480 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83482 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.899999999999999911, 0.1829999999999539495 ) ) ; +#83483 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#83484 = AXIS2_PLACEMENT_3D ( 'NONE', #18501, #80830, #42998 ) ; +#83485 = PRESENTATION_STYLE_ASSIGNMENT (( #52353 ) ) ; +#83486 = EDGE_LOOP ( 'NONE', ( #37384, #41165, #25993, #87824 ) ) ; +#83487 = FILL_AREA_STYLE_COLOUR ( '', #88995 ) ; +#83488 = ORIENTED_EDGE ( 'NONE', *, *, #4988, .T. ) ; +#83489 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83490 = DIRECTION ( 'NONE', ( -2.567390744445670062E-16, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83491 = FILL_AREA_STYLE_COLOUR ( '', #82802 ) ; +#83492 = ADVANCED_FACE ( 'NONE', ( #62156 ), #23843, .F. ) ; +#83493 = PRESENTATION_STYLE_ASSIGNMENT (( #46541 ) ) ; +#83494 = STYLED_ITEM ( 'NONE', ( #79823 ), #34534 ) ; +#83495 = CYLINDRICAL_SURFACE ( 'NONE', #73664, 0.05000000000000012768 ) ; +#83496 = FACE_OUTER_BOUND ( 'NONE', #52817, .T. ) ; +#83497 = FILL_AREA_STYLE_COLOUR ( '', #68677 ) ; +#83498 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37105 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42058, #3751, #27765 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83500 = AXIS2_PLACEMENT_3D ( 'NONE', #77104, #77608, #24024 ) ; +#83499 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.1000000000000000056, -0.2000000000000000111 ) ) ; +#83501 = VECTOR ( 'NONE', #13000, 1000.000000000000114 ) ; +#83502 = ORIENTED_EDGE ( 'NONE', *, *, #49798, .T. ) ; +#83503 = CARTESIAN_POINT ( 'NONE', ( 1.350478891332010267, -1.390055052842650074, 0.8299999999999994049 ) ) ; +#83505 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#83504 = SURFACE_SIDE_STYLE ('',( #35561 ) ) ; +#83506 = VECTOR ( 'NONE', #51322, 1000.000000000000000 ) ; +#83507 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47603, 'distance_accuracy_value', 'NONE'); +#83508 = FILL_AREA_STYLE ('',( #29378 ) ) ; +#83509 = VECTOR ( 'NONE', #93374, 1000.000000000000000 ) ; +#83510 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83511 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.266666666666659946, 0.000000000000000000 ) ) ; +#83512 = SURFACE_STYLE_FILL_AREA ( #35064 ) ; +#83513 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83514 = EDGE_CURVE ( 'NONE', #52650, #11081, #29950, .T. ) ; +#83515 = VERTEX_POINT ( 'NONE', #46260 ) ; +#83516 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18692 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58781, #42437, #50115 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83517 = LINE ( 'NONE', #38052, #29311 ) ; +#83518 = CYLINDRICAL_SURFACE ( 'NONE', #11831, 0.009999999999999998473 ) ; +#83519 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83520 = SURFACE_STYLE_USAGE ( .BOTH. , #83018 ) ; +#83521 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83522 = AXIS2_PLACEMENT_3D ( 'NONE', #76749, #69572, #6717 ) ; +#83523 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83524 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83525 = CARTESIAN_POINT ( 'NONE', ( 11.49435700000000260, 5.988375999999999699, 0.8991599999999999593 ) ) ; +#83526 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.258441558441560026, 0.8100000000000000533 ) ) ; +#83527 = FILL_AREA_STYLE_COLOUR ( '', #86533 ) ; +#83528 = SURFACE_STYLE_FILL_AREA ( #50899 ) ; +#83529 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83530 = LINE ( 'NONE', #13496, #71513 ) ; +#83531 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, -0.000000000000000000 ) ) ; +#83532 = VECTOR ( 'NONE', #5683, 1000.000000000000000 ) ; +#83534 = EDGE_CURVE ( 'NONE', #94750, #76830, #53962, .T. ) ; +#83533 = LINE ( 'NONE', #21727, #1725 ) ; +#83535 = SURFACE_STYLE_FILL_AREA ( #29885 ) ; +#83536 = CARTESIAN_POINT ( 'NONE', ( 1.749115224440590088, -1.150470459123589917, 0.8299999999999997380 ) ) ; +#83537 = CARTESIAN_POINT ( 'NONE', ( 1.783333333333333437, 3.099999999999969891, 0.000000000000000000 ) ) ; +#83538 = LINE ( 'NONE', #28897, #14453 ) ; +#83539 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83540 = CIRCLE ( 'NONE', #50979, 0.1000000000000000194 ) ; +#83541 = ORIENTED_EDGE ( 'NONE', *, *, #36480, .F. ) ; +#83542 = SURFACE_STYLE_FILL_AREA ( #36090 ) ; +#83543 = PRESENTATION_STYLE_ASSIGNMENT (( #44214 ) ) ; +#83544 = SURFACE_STYLE_USAGE ( .BOTH. , #12499 ) ; +#83545 = VECTOR ( 'NONE', #56921, 1000.000000000000000 ) ; +#83546 = AXIS2_PLACEMENT_3D ( 'NONE', #74239, #35462, #6218 ) ; +#83547 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 1.149999999999999911, 0.000000000000000000 ) ) ; +#83548 = AXIS2_PLACEMENT_3D ( 'NONE', #76046, #13183, #43900 ) ; +#83549 = EDGE_CURVE ( 'NONE', #39237, #10790, #7409, .T. ) ; +#83550 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83551 = FACE_OUTER_BOUND ( 'NONE', #74244, .T. ) ; +#83552 = ORIENTED_EDGE ( 'NONE', *, *, #37996, .T. ) ; +#83553 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83554 = LINE ( 'NONE', #90706, #63693 ) ; +#83555 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83556 = STYLED_ITEM ( 'NONE', ( #38861 ), #45885 ) ; +#83557 = ORIENTED_EDGE ( 'NONE', *, *, #32584, .T. ) ; +#83558 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#83559 = CARTESIAN_POINT ( 'NONE', ( 0.01549768115604830028, -1.336414498567920051, 0.8300000000000006262 ) ) ; +#83560 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25495 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38790, #93864, #94892 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83561 = AXIS2_PLACEMENT_3D ( 'NONE', #36928, #29746, #100577 ) ; +#83562 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83563 = EDGE_LOOP ( 'NONE', ( #77273, #25093, #53647, #34895 ) ) ; +#83564 = ORIENTED_EDGE ( 'NONE', *, *, #19995, .F. ) ; +#83565 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49550 ), #60768 ) ; +#83566 = AXIS2_PLACEMENT_3D ( 'NONE', #55350, #86970, #7745 ) ; +#83567 = SURFACE_STYLE_FILL_AREA ( #36116 ) ; +#83568 = FACE_OUTER_BOUND ( 'NONE', #81355, .T. ) ; +#83569 = ORIENTED_EDGE ( 'NONE', *, *, #24065, .F. ) ; +#83570 = LINE ( 'NONE', #29438, #47772 ) ; +#83571 = CARTESIAN_POINT ( 'NONE', ( 0.5106752425455549638, -1.185737326210950071, 0.8299999999999999600 ) ) ; +#83572 = FILL_AREA_STYLE ('',( #43740 ) ) ; +#83573 = FILL_AREA_STYLE ('',( #23807 ) ) ; +#83574 = VECTOR ( 'NONE', #95499, 1000.000000000000000 ) ; +#83575 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#83576 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51019 ) ) ; +#83577 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8472 ) ) ; +#83578 = EDGE_CURVE ( 'NONE', #74415, #90194, #16129, .T. ) ; +#83579 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83581 = ORIENTED_EDGE ( 'NONE', *, *, #62749, .T. ) ; +#83580 = ORIENTED_EDGE ( 'NONE', *, *, #65949, .F. ) ; +#83582 = VECTOR ( 'NONE', #39492, 1000.000000000000000 ) ; +#83583 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83584 = ORIENTED_EDGE ( 'NONE', *, *, #18728, .T. ) ; +#83585 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.1600000000000000033, 1.250000000000000000 ) ) ; +#83586 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83587 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27543, 'distance_accuracy_value', 'NONE'); +#83588 = STYLED_ITEM ( 'NONE', ( #13419 ), #11091 ) ; +#83590 = FACE_OUTER_BOUND ( 'NONE', #84433, .T. ) ; +#83589 = LINE ( 'NONE', #50468, #86787 ) ; +#83591 = LINE ( 'NONE', #6407, #77263 ) ; +#83592 = EDGE_CURVE ( 'NONE', #54968, #27435, #63160, .T. ) ; +#83593 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.5000000000000019984, 0.1829999999999659954 ) ) ; +#83594 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#83595 = CARTESIAN_POINT ( 'NONE', ( -1.196111491924880088, -0.8867570690059840555, 0.8100000000000000533 ) ) ; +#83596 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14400 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47880, #46330, #70335 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83597 = ORIENTED_EDGE ( 'NONE', *, *, #11231, .T. ) ; +#83599 = FILL_AREA_STYLE_COLOUR ( '', #6056 ) ; +#83598 = SURFACE_STYLE_FILL_AREA ( #52450 ) ; +#83600 = EDGE_LOOP ( 'NONE', ( #16747, #58608, #28016, #42274 ) ) ; +#83601 = ORIENTED_EDGE ( 'NONE', *, *, #20364, .T. ) ; +#83602 = CARTESIAN_POINT ( 'NONE', ( 1.274810379711009967, -1.243129529655299992, 0.8299999999999999600 ) ) ; +#83603 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83605 = LINE ( 'NONE', #51968, #93856 ) ; +#83604 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83606 = CARTESIAN_POINT ( 'NONE', ( 1.867699582579569917, -1.228633653069070020, 0.8300000000000004041 ) ) ; +#83607 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83608 = ORIENTED_EDGE ( 'NONE', *, *, #21842, .T. ) ; +#83609 = FILL_AREA_STYLE_COLOUR ( '', #80861 ) ; +#83610 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.383333333333333304, 0.000000000000000000 ) ) ; +#83611 = SURFACE_STYLE_FILL_AREA ( #45749 ) ; +#83612 = ORIENTED_EDGE ( 'NONE', *, *, #27607, .T. ) ; +#83614 = FACE_OUTER_BOUND ( 'NONE', #95579, .T. ) ; +#83613 = LINE ( 'NONE', #45257, #74507 ) ; +#83615 = VERTEX_POINT ( 'NONE', #84595 ) ; +#83616 = ORIENTED_EDGE ( 'NONE', *, *, #40112, .T. ) ; +#83617 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83618 = MANIFOLD_SOLID_BREP ( 'ÊäÈë171', #38713 ) ; +#83619 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83620 = EDGE_CURVE ( 'NONE', #10757, #16995, #3374, .T. ) ; +#83621 = CARTESIAN_POINT ( 'NONE', ( -1.303800513385345861, 1.386221575752817792, 0.8299999999999999600 ) ) ; +#83622 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61481 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34936, #97165, #19586 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83623 = CIRCLE ( 'NONE', #15040, 0.2299999999877400114 ) ; +#83624 = FILL_AREA_STYLE ('',( #97866 ) ) ; +#83626 = ADVANCED_FACE ( 'NONE', ( #45751 ), #41648, .F. ) ; +#83625 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #91747 ) ) ; +#83627 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83628 = EDGE_LOOP ( 'NONE', ( #29280, #46993, #38865, #24645 ) ) ; +#83629 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#83630 = ORIENTED_EDGE ( 'NONE', *, *, #34855, .F. ) ; +#83631 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52649 ), #6845 ) ; +#83632 = CARTESIAN_POINT ( 'NONE', ( -0.1097768158302629971, -0.9623926821384259922, 0.8299999999999999600 ) ) ; +#83633 = LINE ( 'NONE', #15127, #95639 ) ; +#83634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83635 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000009909, -3.123820061220065281, 0.000000000000000000 ) ) ; +#83636 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83637 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83638 = ADVANCED_FACE ( 'NONE', ( #99207 ), #12948, .T. ) ; +#83639 = VERTEX_POINT ( 'NONE', #28357 ) ; +#83640 = ADVANCED_FACE ( 'NONE', ( #66152 ), #81515, .T. ) ; +#83641 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83643 = STYLED_ITEM ( 'NONE', ( #61610 ), #37610 ) ; +#83642 = FILL_AREA_STYLE_COLOUR ( '', #98459 ) ; +#83645 = VECTOR ( 'NONE', #46561, 1000.000000000000000 ) ; +#83644 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83646 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49264 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27264, #66047, #73219 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83647 = LINE ( 'NONE', #100819, #19069 ) ; +#83649 = CARTESIAN_POINT ( 'NONE', ( 1.830402071067120051, -1.199770973383029959, 0.8299999999999999600 ) ) ; +#83648 = VECTOR ( 'NONE', #47441, 1000.000000000000000 ) ; +#83650 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #52675 ) ) ; +#83651 = SURFACE_SIDE_STYLE ('',( #53013 ) ) ; +#83652 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83653 = CYLINDRICAL_SURFACE ( 'NONE', #45096, 0.2500000000000001110 ) ; +#83654 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#83655 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83656 = SURFACE_SIDE_STYLE ('',( #4026 ) ) ; +#83657 = LINE ( 'NONE', #75980, #18596 ) ; +#83658 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58565, #96787, #42702 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83659 = EDGE_CURVE ( 'NONE', #11652, #61742, #92125, .T. ) ; +#83660 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#83661 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44479 ) ) ; +#83662 = VERTEX_POINT ( 'NONE', #100182 ) ; +#83663 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83664 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, -0.02000000000000000042 ) ) ; +#83665 = ORIENTED_EDGE ( 'NONE', *, *, #30833, .F. ) ; +#83666 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#83667 = FACE_OUTER_BOUND ( 'NONE', #15352, .T. ) ; +#83668 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83669 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83670 = LINE ( 'NONE', #6962, #72015 ) ; +#83671 = LINE ( 'NONE', #74511, #100184 ) ; +#83672 = FACE_OUTER_BOUND ( 'NONE', #66755, .T. ) ; +#83673 = EDGE_CURVE ( 'NONE', #64247, #96985, #54872, .T. ) ; +#83674 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.499999999999969802, 0.1829999999999999960 ) ) ; +#83675 = VERTEX_POINT ( 'NONE', #62534 ) ; +#83676 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62481 ), #75499 ) ; +#83677 = LINE ( 'NONE', #66831, #33714 ) ; +#83678 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#83679 = PRESENTATION_STYLE_ASSIGNMENT (( #5023 ) ) ; +#83680 = CARTESIAN_POINT ( 'NONE', ( 1.662784294148539344, -1.164927051866629482, 0.8300000000000000711 ) ) ; +#83681 = FILL_AREA_STYLE_COLOUR ( '', #38794 ) ; +#83682 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83683 = VECTOR ( 'NONE', #38715, 1000.000000000000000 ) ; +#83684 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83685 = SURFACE_SIDE_STYLE ('',( #52542 ) ) ; +#83686 = ORIENTED_EDGE ( 'NONE', *, *, #98141, .T. ) ; +#83687 = ORIENTED_EDGE ( 'NONE', *, *, #96653, .F. ) ; +#83688 = LINE ( 'NONE', #98410, #81377 ) ; +#83689 = ORIENTED_EDGE ( 'NONE', *, *, #10806, .F. ) ; +#83690 = FACE_OUTER_BOUND ( 'NONE', #71485, .T. ) ; +#83691 = VECTOR ( 'NONE', #48406, 1000.000000000000000 ) ; +#83692 = AXIS2_PLACEMENT_3D ( 'NONE', #100131, #89699, #30268 ) ; +#83693 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#83694 = PLANE ( 'NONE', #53216 ) ; +#83695 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#83696 = DIRECTION ( 'NONE', ( 1.000000000000000000, -4.344024262657780858E-34, -4.344024262657779147E-34 ) ) ; +#83697 = EDGE_CURVE ( 'NONE', #60579, #45115, #28701, .T. ) ; +#83698 = CARTESIAN_POINT ( 'NONE', ( -0.06618205349978012464, 0.8082940509174990629, 0.8100000000000003864 ) ) ; +#83699 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83701 = ORIENTED_EDGE ( 'NONE', *, *, #63721, .F. ) ; +#83700 = VERTEX_POINT ( 'NONE', #77308 ) ; +#83702 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83703 = ORIENTED_EDGE ( 'NONE', *, *, #71517, .T. ) ; +#83704 = CARTESIAN_POINT ( 'NONE', ( 1.512057002305370101, -1.084890943604200020, 0.8099999999999981659 ) ) ; +#83705 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66664, 'distance_accuracy_value', 'NONE'); +#83707 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#83706 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1350000000000000089 ) ) ; +#83708 = ORIENTED_EDGE ( 'NONE', *, *, #83135, .F. ) ; +#83709 = EDGE_CURVE ( 'NONE', #66120, #71612, #77604, .T. ) ; +#83710 = ORIENTED_EDGE ( 'NONE', *, *, #11548, .T. ) ; +#83711 = PRESENTATION_STYLE_ASSIGNMENT (( #82701 ) ) ; +#83712 = AXIS2_PLACEMENT_3D ( 'NONE', #74782, #4330, #35502 ) ; +#83713 = AXIS2_PLACEMENT_3D ( 'NONE', #78587, #100446, #8057 ) ; +#83714 = CARTESIAN_POINT ( 'NONE', ( 10.53976199999999963, 4.114543000000000283, 0.8648700000000000276 ) ) ; +#83716 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000089, -0.02000000000000000042 ) ) ; +#83715 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#83717 = SURFACE_STYLE_FILL_AREA ( #75539 ) ; +#83718 = EDGE_CURVE ( 'NONE', #16866, #63256, #55384, .T. ) ; +#83719 = ORIENTED_EDGE ( 'NONE', *, *, #50970, .T. ) ; +#83720 = LINE ( 'NONE', #23433, #77960 ) ; +#83721 = VECTOR ( 'NONE', #65796, 1000.000000000000000 ) ; +#83722 = ORIENTED_EDGE ( 'NONE', *, *, #95509, .F. ) ; +#83723 = FILL_AREA_STYLE_COLOUR ( '', #31424 ) ; +#83724 = EDGE_CURVE ( 'NONE', #81594, #63871, #93098, .T. ) ; +#83725 = AXIS2_PLACEMENT_3D ( 'NONE', #81617, #20802, #73440 ) ; +#83727 = ORIENTED_EDGE ( 'NONE', *, *, #22661, .F. ) ; +#83726 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.123820061220075051, 0.000000000000000000 ) ) ; +#83728 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87794 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25282, #39060, #17062 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83729 = SURFACE_STYLE_FILL_AREA ( #42543 ) ; +#83730 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18094 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83097, #74935, #66749 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83731 = SURFACE_SIDE_STYLE ('',( #52590 ) ) ; +#83732 = VERTEX_POINT ( 'NONE', #38026 ) ; +#83733 = CARTESIAN_POINT ( 'NONE', ( 0.006444788832097659778, -1.283680827045200035, 0.8299999999999999600 ) ) ; +#83734 = VERTEX_POINT ( 'NONE', #6301 ) ; +#83735 = ORIENTED_EDGE ( 'NONE', *, *, #16157, .T. ) ; +#83736 = PRESENTATION_STYLE_ASSIGNMENT (( #12187 ) ) ; +#83737 = SURFACE_SIDE_STYLE ('',( #38765 ) ) ; +#83738 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#83739 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46215 ), #2257 ) ; +#83740 = SURFACE_STYLE_FILL_AREA ( #21937 ) ; +#83741 = ADVANCED_FACE ( 'NONE', ( #61528 ), #23714, .T. ) ; +#83742 = ADVANCED_FACE ( 'NONE', ( #53839 ), #85985, .T. ) ; +#83743 = LINE ( 'NONE', #68878, #72083 ) ; +#83744 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#83745 = DIRECTION ( 'NONE', ( 0.7071075504167442238, 0.7071060119555140355, 0.000000000000000000 ) ) ; +#83746 = VERTEX_POINT ( 'NONE', #48213 ) ; +#83747 = CARTESIAN_POINT ( 'NONE', ( -1.063637804261009956, -1.506193478032149979, 0.8299999999999999600 ) ) ; +#83748 = ORIENTED_EDGE ( 'NONE', *, *, #91150, .F. ) ; +#83749 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.250000000000000000, 0.000000000000000000 ) ) ; +#83750 = SURFACE_STYLE_USAGE ( .BOTH. , #14750 ) ; +#83751 = LINE ( 'NONE', #29608, #88796 ) ; +#83752 = STYLED_ITEM ( 'NONE', ( #68084 ), #53217 ) ; +#83753 = PLANE ( 'NONE', #60967 ) ; +#83754 = FACE_OUTER_BOUND ( 'NONE', #2861, .T. ) ; +#83755 = EDGE_CURVE ( 'NONE', #26712, #63488, #10299, .T. ) ; +#83756 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#83757 = ADVANCED_FACE ( 'NONE', ( #88007 ), #17525, .T. ) ; +#83758 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.05000000000000000971, 0.2100000000000000200 ) ) ; +#83759 = CIRCLE ( 'NONE', #8651, 0.009999999999999998473 ) ; +#83760 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#83761 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83762 = PLANE ( 'NONE', #8111 ) ; +#83763 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93148 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1916, #94803, #33052 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83764 = VECTOR ( 'NONE', #14805, 1000.000000000000000 ) ; +#83765 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139848000000000638, 0.8991599999999999593 ) ) ; +#83767 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#83766 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#83768 = FACE_OUTER_BOUND ( 'NONE', #84939, .T. ) ; +#83769 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999969802, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#83770 = EDGE_CURVE ( 'NONE', #91965, #37700, #55874, .T. ) ; +#83771 = VECTOR ( 'NONE', #59447, 1000.000000000000000 ) ; +#83773 = ORIENTED_EDGE ( 'NONE', *, *, #7661, .F. ) ; +#83772 = AXIS2_PLACEMENT_3D ( 'NONE', #97299, #35580, #27396 ) ; +#83774 = MANIFOLD_SOLID_BREP ( 'ÊäÈë172', #7716 ) ; +#83775 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74202, 'distance_accuracy_value', 'NONE'); +#83776 = FACE_OUTER_BOUND ( 'NONE', #15655, .T. ) ; +#83777 = ADVANCED_FACE ( 'NONE', ( #8444 ), #26400, .F. ) ; +#83778 = PLANE ( 'NONE', #71260 ) ; +#83779 = STYLED_ITEM ( 'NONE', ( #42206 ), #28707 ) ; +#83780 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95894 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43815, #51005, #90276 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83781 = PRESENTATION_STYLE_ASSIGNMENT (( #27669 ) ) ; +#83782 = PLANE ( 'NONE', #98693 ) ; +#83783 = DIRECTION ( 'NONE', ( 0.9317134237021232890, 0.000000000000000000, 0.3631942952377801292 ) ) ; +#83784 = VECTOR ( 'NONE', #69643, 1000.000000000000000 ) ; +#83785 = AXIS2_PLACEMENT_3D ( 'NONE', #13146, #19889, #20380 ) ; +#83786 = EDGE_CURVE ( 'NONE', #78436, #46953, #77677, .T. ) ; +#83787 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#83788 = VERTEX_POINT ( 'NONE', #94283 ) ; +#83789 = LINE ( 'NONE', #54146, #58009 ) ; +#83790 = ADVANCED_FACE ( 'NONE', ( #41221 ), #78481, .F. ) ; +#83791 = ORIENTED_EDGE ( 'NONE', *, *, #66115, .F. ) ; +#83792 = SURFACE_STYLE_USAGE ( .BOTH. , #52651 ) ; +#83793 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41734, 'distance_accuracy_value', 'NONE'); +#83794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19589, 'distance_accuracy_value', 'NONE'); +#83795 = VECTOR ( 'NONE', #88415, 1000.000000000000000 ) ; +#83796 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83797 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83798 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83799 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#83800 = SURFACE_SIDE_STYLE ('',( #99510 ) ) ; +#83801 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83802 = FILL_AREA_STYLE ('',( #11 ) ) ; +#83803 = SURFACE_SIDE_STYLE ('',( #19991 ) ) ; +#83804 = ORIENTED_EDGE ( 'NONE', *, *, #64775, .T. ) ; +#83805 = DIRECTION ( 'NONE', ( 0.7490054809316831763, -0.6625638003500476936, 0.000000000000000000 ) ) ; +#83806 = SURFACE_STYLE_FILL_AREA ( #30145 ) ; +#83807 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83808 = VERTEX_POINT ( 'NONE', #40717 ) ; +#83809 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83810 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83811 = ORIENTED_EDGE ( 'NONE', *, *, #39035, .T. ) ; +#83812 = FILL_AREA_STYLE ('',( #21508 ) ) ; +#83813 = FACE_OUTER_BOUND ( 'NONE', #58534, .T. ) ; +#83814 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83815 = FACE_OUTER_BOUND ( 'NONE', #12434, .T. ) ; +#83816 = EDGE_CURVE ( 'NONE', #92831, #97722, #39684, .T. ) ; +#83818 = ORIENTED_EDGE ( 'NONE', *, *, #74854, .F. ) ; +#83817 = ORIENTED_EDGE ( 'NONE', *, *, #79761, .T. ) ; +#83819 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#83820 = SURFACE_SIDE_STYLE ('',( #75168 ) ) ; +#83821 = ORIENTED_EDGE ( 'NONE', *, *, #97993, .F. ) ; +#83822 = CARTESIAN_POINT ( 'NONE', ( -0.5047584000990159581, -0.9806916243805300359, 0.8299999999999999600 ) ) ; +#83823 = ORIENTED_EDGE ( 'NONE', *, *, #84185, .T. ) ; +#83824 = EDGE_CURVE ( 'NONE', #52824, #71482, #72855, .T. ) ; +#83825 = ADVANCED_FACE ( 'NONE', ( #64191 ), #25903, .T. ) ; +#83826 = ORIENTED_EDGE ( 'NONE', *, *, #40324, .T. ) ; +#83827 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1364, #41689, #94256, #34038 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#83828 = FILL_AREA_STYLE ('',( #98544 ) ) ; +#83829 = PLANE ( 'NONE', #85678 ) ; +#83830 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12398 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31635, #56670, #47460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83831 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14436 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85370, #61917, #30726 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83832 = SURFACE_SIDE_STYLE ('',( #29201 ) ) ; +#83833 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, -13.35000000000000142 ) ) ; +#83835 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83834 = LINE ( 'NONE', #6149, #62781 ) ; +#83836 = VERTEX_POINT ( 'NONE', #59071 ) ; +#83837 = ADVANCED_FACE ( 'NONE', ( #27916 ), #18698, .F. ) ; +#83838 = ORIENTED_EDGE ( 'NONE', *, *, #88298, .F. ) ; +#83839 = VECTOR ( 'NONE', #28077, 1000.000000000000000 ) ; +#83840 = ORIENTED_EDGE ( 'NONE', *, *, #52136, .T. ) ; +#83841 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83842 = STYLED_ITEM ( 'NONE', ( #62799 ), #76491 ) ; +#83843 = ADVANCED_FACE ( 'NONE', ( #75350 ), #49895, .F. ) ; +#83845 = VERTEX_POINT ( 'NONE', #22740 ) ; +#83844 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83846 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83847 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5514 ) ) ; +#83848 = PRESENTATION_STYLE_ASSIGNMENT (( #90997 ) ) ; +#83849 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#83850 = EDGE_LOOP ( 'NONE', ( #88244, #33125, #36563, #69346 ) ) ; +#83851 = CARTESIAN_POINT ( 'NONE', ( -0.6674107142857139685, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#83852 = ORIENTED_EDGE ( 'NONE', *, *, #30840, .T. ) ; +#83853 = AXIS2_PLACEMENT_3D ( 'NONE', #87269, #31637, #33159 ) ; +#83855 = EDGE_LOOP ( 'NONE', ( #97435, #100183, #52593, #74061 ) ) ; +#83854 = PRESENTATION_STYLE_ASSIGNMENT (( #52714 ) ) ; +#83856 = EDGE_CURVE ( 'NONE', #61112, #75732, #45178, .T. ) ; +#83857 = CARTESIAN_POINT ( 'NONE', ( -1.303800513385345861, 1.386221575752817792, 0.8100000000000000533 ) ) ; +#83858 = VECTOR ( 'NONE', #40453, 1000.000000000000000 ) ; +#83859 = CARTESIAN_POINT ( 'NONE', ( -1.195574738698740536, -1.142792474433960148, 0.8099999999998829248 ) ) ; +#83860 = VERTEX_POINT ( 'NONE', #75848 ) ; +#83861 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70807 ), #92006 ) ; +#83862 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#83863 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83864 = SURFACE_STYLE_USAGE ( .BOTH. , #92009 ) ; +#83866 = CARTESIAN_POINT ( 'NONE', ( 1.678890544094119974, -1.445107798742939931, 0.8299999999999999600 ) ) ; +#83865 = CARTESIAN_POINT ( 'NONE', ( 1.157511986614659261, 1.258646575926970490, 0.8100000000000000533 ) ) ; +#83867 = SURFACE_STYLE_USAGE ( .BOTH. , #74710 ) ; +#83868 = PRESENTATION_STYLE_ASSIGNMENT (( #45512 ) ) ; +#83869 = EDGE_CURVE ( 'NONE', #25108, #61494, #77344, .T. ) ; +#83870 = VECTOR ( 'NONE', #67831, 1000.000000000000000 ) ; +#83871 = PRESENTATION_STYLE_ASSIGNMENT (( #12845 ) ) ; +#83872 = ORIENTED_EDGE ( 'NONE', *, *, #75232, .F. ) ; +#83873 = AXIS2_PLACEMENT_3D ( 'NONE', #40653, #25846, #88603 ) ; +#83874 = FILL_AREA_STYLE ('',( #52739 ) ) ; +#83875 = ORIENTED_EDGE ( 'NONE', *, *, #87474, .T. ) ; +#83876 = PRESENTATION_STYLE_ASSIGNMENT (( #36917 ) ) ; +#83878 = FILL_AREA_STYLE ('',( #21581 ) ) ; +#83877 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -8.179221189230645204E-17, -0.6500000000000001332 ) ) ; +#83879 = CARTESIAN_POINT ( 'NONE', ( 1.689681756505250210, -0.9624218420162741205, 0.8100000000000000533 ) ) ; +#83880 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83881 = VECTOR ( 'NONE', #59833, 1000.000000000000000 ) ; +#83882 = PRESENTATION_STYLE_ASSIGNMENT (( #81897 ) ) ; +#83883 = VECTOR ( 'NONE', #16899, 1000.000000000000114 ) ; +#83884 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#83885 = EDGE_LOOP ( 'NONE', ( #77500, #29780, #57367, #28697 ) ) ; +#83886 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83887 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584400679, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#83888 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42377 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14827, #77667, #47530 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#83889 = FILL_AREA_STYLE ('',( #12359 ) ) ; +#83890 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83891 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#83892 = CARTESIAN_POINT ( 'NONE', ( -2.276179938779915091, 3.100000000000000089, 0.000000000000000000 ) ) ; +#83893 = AXIS2_PLACEMENT_3D ( 'NONE', #51672, #97066, #59351 ) ; +#83894 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #70894, #40264 ), + ( #32093, #47910 ), + ( #48442, #85181 ), + ( #15198, #31578 ), + ( #63262, #71392 ), + ( #16723, #69860 ), + ( #31073, #33616 ), + ( #50467, #1959 ), + ( #95340, #57112 ), + ( #41771, #26457 ), + ( #89238, #64238 ), + ( #50955, #80582 ), + ( #12035, #49948 ), + ( #71908, #96856 ), + ( #82091, #3955 ), + ( #88719, #18241 ), + ( #65757, #64738 ), + ( #89724, #81091 ), + ( #17745, #33096 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06797158385402929381, 0.1342600110226029875, 0.1996375432477029976, 0.2636133251149819778, 0.3266798409903740041, 0.3873044356296519997, 0.4467275391483779834, 0.5050530114610609633, 0.5632809992818500477, 0.6212441432870500213, 0.6796615349141380547, 0.7395831398408979629, 0.8010350593152619769, 0.8644459444340329979, 0.9304086162470880383, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#83895 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#83896 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46839, 'distance_accuracy_value', 'NONE'); +#83897 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#83898 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83899 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#83900 = VERTEX_POINT ( 'NONE', #6818 ) ; +#83901 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#83902 = ADVANCED_FACE ( 'NONE', ( #30361 ), #5860, .F. ) ; +#83903 = ORIENTED_EDGE ( 'NONE', *, *, #95826, .T. ) ; +#83904 = SURFACE_SIDE_STYLE ('',( #92533 ) ) ; +#83905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17403, 'distance_accuracy_value', 'NONE'); +#83906 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79049, 'distance_accuracy_value', 'NONE'); +#83907 = CARTESIAN_POINT ( 'NONE', ( 1.077065871219029969, -0.9985765647821309710, 0.8299999999999999600 ) ) ; +#83908 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83909 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83910 = CARTESIAN_POINT ( 'NONE', ( 1.702357802111380103, -0.9001170352889870108, 0.8100000000000000533 ) ) ; +#83912 = ADVANCED_FACE ( 'NONE', ( #93136 ), #21225, .T. ) ; +#83911 = LINE ( 'NONE', #44575, #14565 ) ; +#83913 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83914 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000010214, -3.123820061220065281, -0.02000000000000000042 ) ) ; +#83915 = EDGE_LOOP ( 'NONE', ( #33649, #84904, #89081, #31828 ) ) ; +#83916 = SURFACE_SIDE_STYLE ('',( #52783 ) ) ; +#83917 = SURFACE_SIDE_STYLE ('',( #37472 ) ) ; +#83918 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84986, 'distance_accuracy_value', 'NONE'); +#83920 = VECTOR ( 'NONE', #1843, 1000.000000000000000 ) ; +#83919 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.01500000000000001159, 0.2399999999999999911 ) ) ; +#83921 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51293 ), #70875 ) ; +#83922 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#83923 = ORIENTED_EDGE ( 'NONE', *, *, #11515, .T. ) ; +#83924 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83925 = STYLED_ITEM ( 'NONE', ( #33731 ), #97700 ) ; +#83926 = CARTESIAN_POINT ( 'NONE', ( 7.700000000000000178, 0.000000000000000000, 0.8648700000000000276 ) ) ; +#83927 = CYLINDRICAL_SURFACE ( 'NONE', #39235, 0.05000000000000012768 ) ; +#83928 = ADVANCED_FACE ( 'NONE', ( #29393 ), #60563, .T. ) ; +#83929 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#83930 = FILL_AREA_STYLE ('',( #5774 ) ) ; +#83931 = ORIENTED_EDGE ( 'NONE', *, *, #93476, .T. ) ; +#83932 = SURFACE_STYLE_USAGE ( .BOTH. , #46615 ) ; +#83933 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90148, 'distance_accuracy_value', 'NONE'); +#83934 = SURFACE_STYLE_USAGE ( .BOTH. , #12902 ) ; +#83935 = VECTOR ( 'NONE', #34293, 1000.000000000000000 ) ; +#83936 = MANIFOLD_SOLID_BREP ( 'ÊäÈë91', #14170 ) ; +#83937 = ORIENTED_EDGE ( 'NONE', *, *, #21858, .T. ) ; +#83938 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#83939 = AXIS2_PLACEMENT_3D ( 'NONE', #93556, #38986, #94067 ) ; +#83940 = SURFACE_STYLE_FILL_AREA ( #75775 ) ; +#83941 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#83942 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83943 = FACE_OUTER_BOUND ( 'NONE', #31971, .T. ) ; +#83944 = VERTEX_POINT ( 'NONE', #8835 ) ; +#83945 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83946 = EDGE_CURVE ( 'NONE', #85194, #18909, #2296, .T. ) ; +#83947 = ORIENTED_EDGE ( 'NONE', *, *, #30323, .F. ) ; +#83949 = ORIENTED_EDGE ( 'NONE', *, *, #22378, .T. ) ; +#83948 = LINE ( 'NONE', #13950, #67233 ) ; +#83950 = SURFACE_SIDE_STYLE ('',( #52820 ) ) ; +#83951 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59594 ), #28560 ) ; +#83953 = CARTESIAN_POINT ( 'NONE', ( -1.384335136307129899, -1.374349516767729984, 0.8299999999999999600 ) ) ; +#83952 = FACE_OUTER_BOUND ( 'NONE', #71539, .T. ) ; +#83954 = SURFACE_STYLE_USAGE ( .BOTH. , #92099 ) ; +#83955 = SURFACE_STYLE_USAGE ( .BOTH. , #100643 ) ; +#83956 = ORIENTED_EDGE ( 'NONE', *, *, #24706, .F. ) ; +#83958 = ADVANCED_FACE ( 'NONE', ( #9351 ), #10335, .F. ) ; +#83957 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83959 = CARTESIAN_POINT ( 'NONE', ( -2.649999999999999911, -3.100000000000000533, 0.000000000000000000 ) ) ; +#83960 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#83961 = EDGE_LOOP ( 'NONE', ( #38493, #7080, #2546, #87808 ) ) ; +#83962 = CARTESIAN_POINT ( 'NONE', ( 7.032513000000000680, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#83963 = AXIS2_PLACEMENT_3D ( 'NONE', #91851, #82217, #60741 ) ; +#83964 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #46470 ) ) ; +#83965 = PRESENTATION_STYLE_ASSIGNMENT (( #13964 ) ) ; +#83966 = ORIENTED_EDGE ( 'NONE', *, *, #75436, .T. ) ; +#83969 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#83968 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#83967 = VECTOR ( 'NONE', #68723, 1000.000000000000000 ) ; +#83970 = VECTOR ( 'NONE', #68327, 1000.000000000000000 ) ; +#83971 = ORIENTED_EDGE ( 'NONE', *, *, #32112, .T. ) ; +#83972 = VECTOR ( 'NONE', #25119, 1000.000000000000000 ) ; +#83973 = EDGE_CURVE ( 'NONE', #89063, #59551, #63073, .T. ) ; +#83974 = EDGE_CURVE ( 'NONE', #86832, #99445, #63585, .T. ) ; +#83975 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67930, #65963, #74125, #98509 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#83977 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#83976 = LINE ( 'NONE', #29834, #52819 ) ; +#83978 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.700000000000000178, -1.793208184573746020E-89 ) ) ; +#83979 = AXIS2_PLACEMENT_3D ( 'NONE', #98058, #67472, #51699 ) ; +#83980 = EDGE_CURVE ( 'NONE', #34518, #39991, #68430, .T. ) ; +#83981 = CARTESIAN_POINT ( 'NONE', ( 0.2415003227679569930, -1.304818455916720188, 0.8299999999999982947 ) ) ; +#83982 = ADVANCED_FACE ( 'NONE', ( #6093 ), #83778, .T. ) ; +#83983 = AXIS2_PLACEMENT_3D ( 'NONE', #33446, #42600, #64570 ) ; +#83984 = EDGE_LOOP ( 'NONE', ( #19796, #58364, #70451, #43088 ) ) ; +#83985 = SURFACE_STYLE_FILL_AREA ( #90643 ) ; +#83986 = EDGE_LOOP ( 'NONE', ( #90069, #65083, #100327, #25115 ) ) ; +#83987 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#83988 = VECTOR ( 'NONE', #36708, 1000.000000000000000 ) ; +#83989 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 1.983599999999999808, 0.8648700000000000276 ) ) ; +#83990 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#83991 = ADVANCED_FACE ( 'NONE', ( #21474 ), #66077, .F. ) ; +#83992 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#83993 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, -8.400000000000000355, -11.91999999999999993 ) ) ; +#83994 = FACE_OUTER_BOUND ( 'NONE', #44244, .T. ) ; +#83995 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#83996 = ADVANCED_FACE ( 'NONE', ( #88548 ), #37331, .F. ) ; +#83997 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#83998 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#83999 = ORIENTED_EDGE ( 'NONE', *, *, #80875, .F. ) ; +#84000 = SURFACE_SIDE_STYLE ('',( #91637 ) ) ; +#84001 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84003 = SURFACE_STYLE_FILL_AREA ( #93617 ) ; +#84002 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84004 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#84006 = MANIFOLD_SOLID_BREP ( 'ÊäÈë157', #28869 ) ; +#84005 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#84007 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84008 = LINE ( 'NONE', #29859, #10874 ) ; +#84009 = SURFACE_STYLE_USAGE ( .BOTH. , #68156 ) ; +#84010 = SURFACE_STYLE_FILL_AREA ( #51876 ) ; +#84011 = ORIENTED_EDGE ( 'NONE', *, *, #26201, .F. ) ; +#84012 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84013 = LINE ( 'NONE', #30351, #52754 ) ; +#84014 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#84015 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#84016 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#84017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70971 ), #48012 ) ; +#84018 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84019 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84020 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7177 ), #90500 ) ; +#84021 = FILL_AREA_STYLE_COLOUR ( '', #34360 ) ; +#84022 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#84023 = FILL_AREA_STYLE ('',( #21721 ) ) ; +#84024 = CYLINDRICAL_SURFACE ( 'NONE', #12622, 0.1099999999999998479 ) ; +#84025 = SURFACE_STYLE_USAGE ( .BOTH. , #77348 ) ; +#84026 = VECTOR ( 'NONE', #8445, 1000.000000000000000 ) ; +#84027 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84028 = EDGE_CURVE ( 'NONE', #57725, #65011, #69937, .T. ) ; +#84029 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#84030 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84031 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22354, 'distance_accuracy_value', 'NONE'); +#84032 = STYLED_ITEM ( 'NONE', ( #86939 ), #89963 ) ; +#84033 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91714 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1504, #69902, #54107 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84034 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#84035 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84036 = EDGE_CURVE ( 'NONE', #16557, #63527, #62316, .T. ) ; +#84037 = LINE ( 'NONE', #76359, #83501 ) ; +#84038 = ORIENTED_EDGE ( 'NONE', *, *, #70813, .T. ) ; +#84039 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84040 = VECTOR ( 'NONE', #79948, 1000.000000000000000 ) ; +#84041 = PLANE ( 'NONE', #99083 ) ; +#84042 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66957, 'distance_accuracy_value', 'NONE'); +#84043 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84044 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, 3.266666666666667052, 3.495651678170021751E-76 ) ) ; +#84045 = FILL_AREA_STYLE_COLOUR ( '', #63385 ) ; +#84046 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85640 ) ) ; +#84047 = AXIS2_PLACEMENT_3D ( 'NONE', #18727, #81067, #50438 ) ; +#84048 = LINE ( 'NONE', #44220, #80121 ) ; +#84049 = STYLED_ITEM ( 'NONE', ( #60833 ), #25707 ) ; +#84050 = PLANE ( 'NONE', #98837 ) ; +#84051 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000013767, -3.500000000000000444, 0.000000000000000000 ) ) ; +#84052 = ORIENTED_EDGE ( 'NONE', *, *, #35698, .T. ) ; +#84053 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84054 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84055 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93, 'distance_accuracy_value', 'NONE'); +#84056 = VECTOR ( 'NONE', #17449, 999.9999999999998863 ) ; +#84057 = CARTESIAN_POINT ( 'NONE', ( 0.005236623695644900336, -1.379727385542079965, 0.8300000000000006262 ) ) ; +#84058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84059 = AXIS2_PLACEMENT_3D ( 'NONE', #91565, #13387, #75749 ) ; +#84060 = FACE_OUTER_BOUND ( 'NONE', #82475, .T. ) ; +#84061 = EDGE_CURVE ( 'NONE', #67375, #4416, #70443, .T. ) ; +#84062 = ORIENTED_EDGE ( 'NONE', *, *, #50149, .T. ) ; +#84063 = ORIENTED_EDGE ( 'NONE', *, *, #46616, .F. ) ; +#84064 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71190 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37035, #28363, #27885 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84065 = FILL_AREA_STYLE ('',( #43246 ) ) ; +#84066 = ORIENTED_EDGE ( 'NONE', *, *, #23397, .F. ) ; +#84067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84068 = CARTESIAN_POINT ( 'NONE', ( 0.04624266161326810037, -1.451435312150680224, 0.8299999999999999600 ) ) ; +#84069 = CARTESIAN_POINT ( 'NONE', ( 0.4504580075531440242, -1.245164908316749974, 0.8299999999999999600 ) ) ; +#84070 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#84071 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#84072 = STYLED_ITEM ( 'NONE', ( #21558 ), #4571 ) ; +#84073 = LINE ( 'NONE', #84559, #55794 ) ; +#84074 = ORIENTED_EDGE ( 'NONE', *, *, #37039, .T. ) ; +#84075 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #90563 ), #40059 ) ; +#84076 = VERTEX_POINT ( 'NONE', #500 ) ; +#84077 = LINE ( 'NONE', #82582, #45884 ) ; +#84078 = VECTOR ( 'NONE', #38228, 1000.000000000000000 ) ; +#84079 = SURFACE_STYLE_USAGE ( .BOTH. , #21785 ) ; +#84080 = EDGE_LOOP ( 'NONE', ( #5625, #48181, #53168, #49567 ) ) ; +#84081 = VECTOR ( 'NONE', #79607, 1000.000000000000000 ) ; +#84082 = VERTEX_POINT ( 'NONE', #1022 ) ; +#84083 = EDGE_LOOP ( 'NONE', ( #78091, #35034, #90469, #74559 ) ) ; +#84084 = CARTESIAN_POINT ( 'NONE', ( 1.303722762681589931, -1.254158608853950030, 0.8100000000000000533 ) ) ; +#84086 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, -1.164082792207790096, 0.8100000000000000533 ) ) ; +#84085 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#84087 = AXIS2_PLACEMENT_3D ( 'NONE', #90892, #75566, #13202 ) ; +#84088 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#84089 = PRESENTATION_STYLE_ASSIGNMENT (( #68740 ) ) ; +#84090 = ORIENTED_EDGE ( 'NONE', *, *, #21267, .T. ) ; +#84091 = FILL_AREA_STYLE_COLOUR ( '', #45010 ) ; +#84092 = EDGE_CURVE ( 'NONE', #82955, #99548, #55181, .T. ) ; +#84093 = SURFACE_SIDE_STYLE ('',( #36152 ) ) ; +#84094 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84095 = VECTOR ( 'NONE', #79670, 1000.000000000000000 ) ; +#84096 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#84097 = VECTOR ( 'NONE', #15399, 1000.000000000000000 ) ; +#84098 = VERTEX_POINT ( 'NONE', #31653 ) ; +#84100 = SURFACE_STYLE_FILL_AREA ( #99334 ) ; +#84099 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.2999999999999999889, -13.54999999999999893 ) ) ; +#84101 = PLANE ( 'NONE', #33166 ) ; +#84102 = VERTEX_POINT ( 'NONE', #62831 ) ; +#84103 = ORIENTED_EDGE ( 'NONE', *, *, #29114, .F. ) ; +#84104 = CARTESIAN_POINT ( 'NONE', ( 1.111329997291490068, -1.502675929081449979, 0.8100000000000000533 ) ) ; +#84105 = STYLED_ITEM ( 'NONE', ( #46630 ), #49626 ) ; +#84106 = MANIFOLD_SOLID_BREP ( 'ÊäÈë17', #86007 ) ; +#84107 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#84108 = LINE ( 'NONE', #74956, #39976 ) ; +#84109 = CARTESIAN_POINT ( 'NONE', ( 11.62059900000000034, 10.98312999999999917, 0.8991599999999999593 ) ) ; +#84110 = CARTESIAN_POINT ( 'NONE', ( -1.233736516140655270, -0.9639334565574939617, 0.8100000000000145972 ) ) ; +#84111 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58070 ) ) ; +#84112 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #78154 ) ; +#84113 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.185754870129869909, 0.8099999999999875078 ) ) ; +#84114 = EDGE_CURVE ( 'NONE', #35471, #81506, #77613, .T. ) ; +#84115 = ORIENTED_EDGE ( 'NONE', *, *, #13857, .F. ) ; +#84116 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15572 ), #54780 ) ; +#84117 = ORIENTED_EDGE ( 'NONE', *, *, #87500, .T. ) ; +#84118 = AXIS2_PLACEMENT_3D ( 'NONE', #19957, #68407, #35815 ) ; +#84119 = SURFACE_SIDE_STYLE ('',( #20829 ) ) ; +#84120 = CARTESIAN_POINT ( 'NONE', ( -0.05398490405131480679, -0.9763607356531520676, 0.8299999999999999600 ) ) ; +#84121 = FILL_AREA_STYLE ('',( #92266 ) ) ; +#84122 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84123 = VECTOR ( 'NONE', #69949, 1000.000000000000000 ) ; +#84124 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84125 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84126 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71081 ) ) ; +#84127 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84128 = LINE ( 'NONE', #6452, #98819 ) ; +#84129 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84130 = ORIENTED_EDGE ( 'NONE', *, *, #24266, .T. ) ; +#84131 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84132 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56484 ), #66213 ) ; +#84133 = FILL_AREA_STYLE_COLOUR ( '', #12012 ) ; +#84134 = FACE_OUTER_BOUND ( 'NONE', #50088, .T. ) ; +#84135 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#84136 = PLANE ( 'NONE', #11404 ) ; +#84137 = SURFACE_STYLE_FILL_AREA ( #21343 ) ; +#84138 = AXIS2_PLACEMENT_3D ( 'NONE', #75090, #90381, #36777 ) ; +#84139 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.000000000000000000 ) ) ; +#84140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74123 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39876, #40399, #46502 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84141 = EDGE_CURVE ( 'NONE', #28324, #21325, #76600, .T. ) ; +#84142 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#84143 = PRESENTATION_STYLE_ASSIGNMENT (( #94287 ) ) ; +#84144 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#84145 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#84146 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12350 ), #38517 ) ; +#84147 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#84148 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48275, 'distance_accuracy_value', 'NONE'); +#84149 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84151 = EDGE_CURVE ( 'NONE', #71553, #5198, #95931, .T. ) ; +#84150 = FILL_AREA_STYLE_COLOUR ( '', #4622 ) ; +#84152 = CARTESIAN_POINT ( 'NONE', ( 0.6431619866146580655, 0.5992840759269659756, 0.8100000000000000533 ) ) ; +#84153 = EDGE_LOOP ( 'NONE', ( #20414, #420, #90963, #92819 ) ) ; +#84154 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.000000000000000000 ) ) ; +#84155 = FILL_AREA_STYLE ('',( #28047 ) ) ; +#84156 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000533, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#84157 = FILL_AREA_STYLE_COLOUR ( '', #2066 ) ; +#84158 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98233, 'distance_accuracy_value', 'NONE'); +#84159 = FILL_AREA_STYLE_COLOUR ( '', #47581 ) ; +#84160 = VECTOR ( 'NONE', #72298, 1000.000000000000000 ) ; +#84161 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#84162 = CARTESIAN_POINT ( 'NONE', ( 1.441558441558439929, -1.337215909090909927, 0.8099999999999111244 ) ) ; +#84163 = VECTOR ( 'NONE', #12584, 1000.000000000000000 ) ; +#84164 = ORIENTED_EDGE ( 'NONE', *, *, #95883, .T. ) ; +#84165 = FILL_AREA_STYLE ('',( #37713 ) ) ; +#84166 = SURFACE_STYLE_FILL_AREA ( #83180 ) ; +#84167 = MANIFOLD_SOLID_BREP ( 'ÊäÈë154', #17491 ) ; +#84168 = PLANE ( 'NONE', #45413 ) ; +#84169 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82038, 'distance_accuracy_value', 'NONE'); +#84170 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84171 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84172 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28074, 'distance_accuracy_value', 'NONE'); +#84173 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95514 ), #40170 ) ; +#84174 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84175 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14008 ) ) ; +#84176 = PLANE ( 'NONE', #46089 ) ; +#84177 = VERTEX_POINT ( 'NONE', #96432 ) ; +#84179 = VERTEX_POINT ( 'NONE', #27044 ) ; +#84178 = VECTOR ( 'NONE', #74306, 1000.000000000000000 ) ; +#84180 = ORIENTED_EDGE ( 'NONE', *, *, #94261, .T. ) ; +#84181 = CARTESIAN_POINT ( 'NONE', ( -0.3092775381631849840, -1.357596283920579960, 0.8299999999999999600 ) ) ; +#84182 = STYLED_ITEM ( 'NONE', ( #17646 ), #78727 ) ; +#84183 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84184 = PLANE ( 'NONE', #5756 ) ; +#84185 = EDGE_CURVE ( 'NONE', #10140, #54922, #17326, .T. ) ; +#84186 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#84187 = CARTESIAN_POINT ( 'NONE', ( -0.9699999999999999734, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#84188 = LINE ( 'NONE', #83695, #18625 ) ; +#84189 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #50867 ) ; +#84190 = LINE ( 'NONE', #38234, #78515 ) ; +#84191 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84192 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#84194 = ORIENTED_EDGE ( 'NONE', *, *, #86374, .F. ) ; +#84193 = ORIENTED_EDGE ( 'NONE', *, *, #78848, .T. ) ; +#84195 = VECTOR ( 'NONE', #60661, 1000.000000000000000 ) ; +#84196 = ORIENTED_EDGE ( 'NONE', *, *, #619, .F. ) ; +#84197 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84198 = VECTOR ( 'NONE', #30915, 1000.000000000000000 ) ; +#84199 = FILL_AREA_STYLE ('',( #73651 ) ) ; +#84201 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000058398, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#84200 = FILL_AREA_STYLE_COLOUR ( '', #44032 ) ; +#84202 = VERTEX_POINT ( 'NONE', #42361 ) ; +#84203 = EDGE_CURVE ( 'NONE', #90126, #37758, #42810, .T. ) ; +#84204 = ORIENTED_EDGE ( 'NONE', *, *, #38140, .T. ) ; +#84205 = EDGE_CURVE ( 'NONE', #93815, #14672, #70831, .T. ) ; +#84206 = VECTOR ( 'NONE', #78581, 1000.000000000000000 ) ; +#84207 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84208 = STYLED_ITEM ( 'NONE', ( #100726 ), #99628 ) ; +#84209 = SURFACE_SIDE_STYLE ('',( #37264 ) ) ; +#84210 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, 0.4750000000000000333, -0.2500000000000000000 ) ) ; +#84211 = EDGE_LOOP ( 'NONE', ( #10263, #97713, #34524, #39762 ) ) ; +#84212 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -11.57000000000000028 ) ) ; +#84213 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51601 ) ) ; +#84214 = VERTEX_POINT ( 'NONE', #32683 ) ; +#84215 = EDGE_LOOP ( 'NONE', ( #660, #93424, #34649, #50811 ) ) ; +#84216 = SURFACE_STYLE_USAGE ( .BOTH. , #29092 ) ; +#84217 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57835 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96734, #74801, #67603 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84218 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84219 = AXIS2_PLACEMENT_3D ( 'NONE', #63147, #47805, #1343 ) ; +#84222 = ORIENTED_EDGE ( 'NONE', *, *, #28638, .T. ) ; +#84221 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79470, 'distance_accuracy_value', 'NONE'); +#84220 = SURFACE_STYLE_USAGE ( .BOTH. , #53086 ) ; +#84223 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#84225 = ADVANCED_FACE ( 'NONE', ( #64314 ), #41849, .T. ) ; +#84224 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27185 ) ) ; +#84226 = ORIENTED_EDGE ( 'NONE', *, *, #68886, .F. ) ; +#84227 = CARTESIAN_POINT ( 'NONE', ( 0.01061219417860849966, -1.294636995308309890, 0.8299999999999999600 ) ) ; +#84228 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2849999999999999756, 0.1399999999999999856 ) ) ; +#84229 = ORIENTED_EDGE ( 'NONE', *, *, #46411, .T. ) ; +#84230 = ORIENTED_EDGE ( 'NONE', *, *, #46689, .F. ) ; +#84231 = PRESENTATION_STYLE_ASSIGNMENT (( #68869 ) ) ; +#84232 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84233 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#84234 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84235 = AXIS2_PLACEMENT_3D ( 'NONE', #3126, #24637, #88394 ) ; +#84236 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#84237 = LINE ( 'NONE', #38770, #42771 ) ; +#84238 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666647068, -0.2999999999999999889, 3.495651678170021751E-76 ) ) ; +#84239 = CARTESIAN_POINT ( 'NONE', ( 0.2761799387799149796, -3.099999999999980105, 0.000000000000000000 ) ) ; +#84240 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#84241 = VERTEX_POINT ( 'NONE', #51034 ) ; +#84242 = CARTESIAN_POINT ( 'NONE', ( 0.4526194431797169737, -1.137806428429579908, 0.8100000000000000533 ) ) ; +#84243 = ORIENTED_EDGE ( 'NONE', *, *, #45947, .T. ) ; +#84244 = SURFACE_STYLE_USAGE ( .BOTH. , #91889 ) ; +#84245 = CARTESIAN_POINT ( 'NONE', ( 0.9685869866146578078, 0.4055590759269656620, 0.8100000000000000533 ) ) ; +#84246 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84247 = VECTOR ( 'NONE', #52896, 1000.000000000000000 ) ; +#84248 = FACE_OUTER_BOUND ( 'NONE', #20420, .T. ) ; +#84250 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84249 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#84251 = CARTESIAN_POINT ( 'NONE', ( 1.726111644763860253, -0.9656914468017120390, 0.8299999999999999600 ) ) ; +#84252 = FILL_AREA_STYLE ('',( #53119 ) ) ; +#84253 = LINE ( 'NONE', #14246, #31518 ) ; +#84254 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #71198 ) ) ; +#84255 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#84256 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28781 ) ) ; +#84257 = FACE_OUTER_BOUND ( 'NONE', #32617, .T. ) ; +#84258 = SURFACE_STYLE_USAGE ( .BOTH. , #46426 ) ; +#84259 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84260 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84261 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84262 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84263 = EDGE_CURVE ( 'NONE', #7067, #79084, #37179, .T. ) ; +#84264 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#84265 = FACE_OUTER_BOUND ( 'NONE', #80320, .T. ) ; +#84266 = FILL_AREA_STYLE_COLOUR ( '', #3282 ) ; +#84267 = SURFACE_SIDE_STYLE ('',( #53133 ) ) ; +#84268 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38633 ) ) ; +#84269 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #15537, 'distance_accuracy_value', 'NONE'); +#84270 = EDGE_LOOP ( 'NONE', ( #35929, #81500, #61222, #94626 ) ) ; +#84271 = CARTESIAN_POINT ( 'NONE', ( -0.9926480063939780996, -1.365766081162230083, 0.8100000000000000533 ) ) ; +#84272 = EDGE_CURVE ( 'NONE', #951, #2574, #97439, .T. ) ; +#84273 = MANIFOLD_SOLID_BREP ( 'ÊäÈë95', #61693 ) ; +#84274 = SURFACE_STYLE_USAGE ( .BOTH. , #29631 ) ; +#84275 = FILL_AREA_STYLE_COLOUR ( '', #17675 ) ; +#84276 = CARTESIAN_POINT ( 'NONE', ( 1.783333333333333437, -3.099999999999969891, 0.000000000000000000 ) ) ; +#84277 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#84278 = DIRECTION ( 'NONE', ( -0.5743404272044019265, 0.8186165608382627301, 0.000000000000000000 ) ) ; +#84279 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84280 = LINE ( 'NONE', #37821, #30105 ) ; +#84281 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98409 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62103, #15045, #276 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84282 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64687 ), #77717 ) ; +#84283 = ORIENTED_EDGE ( 'NONE', *, *, #54567, .T. ) ; +#84284 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84285 = ORIENTED_EDGE ( 'NONE', *, *, #65633, .T. ) ; +#84286 = PRESENTATION_STYLE_ASSIGNMENT (( #20999 ) ) ; +#84287 = SURFACE_STYLE_USAGE ( .BOTH. , #53153 ) ; +#84288 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#84289 = LINE ( 'NONE', #36829, #100295 ) ; +#84290 = CARTESIAN_POINT ( 'NONE', ( 1.091567153405927026, -0.9032100794317501347, 0.8100000000000506795 ) ) ; +#84291 = AXIS2_PLACEMENT_3D ( 'NONE', #35394, #19009, #26211 ) ; +#84292 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.000000000000000000 ) ) ; +#84293 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84294 = SURFACE_SIDE_STYLE ('',( #37353 ) ) ; +#84295 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84296 = ORIENTED_EDGE ( 'NONE', *, *, #82973, .F. ) ; +#84297 = FILL_AREA_STYLE ('',( #13259 ) ) ; +#84298 = PLANE ( 'NONE', #17744 ) ; +#84299 = ORIENTED_EDGE ( 'NONE', *, *, #31323, .F. ) ; +#84300 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#84301 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5488 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23926, #33078, #32579 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84302 = LINE ( 'NONE', #92433, #53378 ) ; +#84303 = EDGE_LOOP ( 'NONE', ( #45261, #74666, #17963, #11319 ) ) ; +#84304 = ADVANCED_FACE ( 'NONE', ( #5982 ), #28526, .F. ) ; +#84305 = EDGE_CURVE ( 'NONE', #35510, #36018, #36706, .T. ) ; +#84306 = LINE ( 'NONE', #533, #2338 ) ; +#84307 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84308 = CARTESIAN_POINT ( 'NONE', ( 10.32001999999999953, 2.133599999999999941, 0.8991599999999999593 ) ) ; +#84309 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84311 = VERTEX_POINT ( 'NONE', #86152 ) ; +#84310 = ORIENTED_EDGE ( 'NONE', *, *, #81987, .F. ) ; +#84312 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01085786437626904202, 0.1434314575050762153 ) ) ; +#84313 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84314 = VERTEX_POINT ( 'NONE', #93280 ) ; +#84315 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.000000000000000000, -11.41999999999999993 ) ) ; +#84316 = AXIS2_PLACEMENT_3D ( 'NONE', #79510, #9470, #9957 ) ; +#84317 = CARTESIAN_POINT ( 'NONE', ( -0.5440898474478359503, -0.9715902597976999733, 0.8299999999999999600 ) ) ; +#84318 = ORIENTED_EDGE ( 'NONE', *, *, #35079, .F. ) ; +#84319 = EDGE_CURVE ( 'NONE', #79295, #89943, #69534, .T. ) ; +#84320 = CIRCLE ( 'NONE', #32150, 0.01000000000000002623 ) ; +#84321 = VERTEX_POINT ( 'NONE', #84156 ) ; +#84322 = EDGE_CURVE ( 'NONE', #40353, #80733, #57483, .T. ) ; +#84323 = FILL_AREA_STYLE ('',( #85826 ) ) ; +#84324 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84325 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84326 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84327 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84328 = ORIENTED_EDGE ( 'NONE', *, *, #14455, .T. ) ; +#84329 = ORIENTED_EDGE ( 'NONE', *, *, #86509, .T. ) ; +#84330 = LINE ( 'NONE', #54197, #55105 ) ; +#84331 = VERTEX_POINT ( 'NONE', #76485 ) ; +#84332 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99394 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84554, #69726, #61106 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84333 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95771 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49809, #95705, #32962 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84334 = VECTOR ( 'NONE', #87400, 1000.000000000000114 ) ; +#84336 = ORIENTED_EDGE ( 'NONE', *, *, #81284, .T. ) ; +#84335 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#84337 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84338 = AXIS2_PLACEMENT_3D ( 'NONE', #44964, #28672, #67458 ) ; +#84339 = EDGE_CURVE ( 'NONE', #48479, #46875, #33040, .T. ) ; +#84340 = PLANE ( 'NONE', #45722 ) ; +#84341 = FILL_AREA_STYLE ('',( #22044 ) ) ; +#84342 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84343 = ORIENTED_EDGE ( 'NONE', *, *, #61071, .F. ) ; +#84344 = FACE_OUTER_BOUND ( 'NONE', #9373, .T. ) ; +#84345 = CLOSED_SHELL ( 'NONE', ( #70598, #55486, #110, #93542, #38050, #44298 ) ) ; +#84346 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, 0.000000000000000000 ) ) ; +#84347 = ORIENTED_EDGE ( 'NONE', *, *, #20731, .F. ) ; +#84348 = EDGE_CURVE ( 'NONE', #83217, #78342, #91798, .T. ) ; +#84349 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#84351 = ORIENTED_EDGE ( 'NONE', *, *, #7828, .T. ) ; +#84350 = DIRECTION ( 'NONE', ( 0.7071075504167435577, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#84352 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26168 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49588, #81742, #27615 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84353 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 7.671291000000000082, 0.8648700000000000276 ) ) ; +#84354 = EDGE_CURVE ( 'NONE', #62754, #95596, #56211, .T. ) ; +#84355 = SURFACE_STYLE_FILL_AREA ( #53222 ) ; +#84356 = CARTESIAN_POINT ( 'NONE', ( -0.9453861132075022100, -1.238048172223545684, 0.8099999999998126476 ) ) ; +#84358 = EDGE_CURVE ( 'NONE', #19154, #21305, #6959, .T. ) ; +#84357 = CARTESIAN_POINT ( 'NONE', ( -1.870129870129870087, -1.500000000000000222, 0.8100000000000000533 ) ) ; +#84359 = ORIENTED_EDGE ( 'NONE', *, *, #33471, .F. ) ; +#84360 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84361 = ADVANCED_FACE ( 'NONE', ( #46320 ), #70848, .T. ) ; +#84362 = SURFACE_STYLE_USAGE ( .BOTH. , #53233 ) ; +#84364 = CARTESIAN_POINT ( 'NONE', ( 1.608267340221630093, -1.417598257925390293, 0.8299999999999999600 ) ) ; +#84363 = CARTESIAN_POINT ( 'NONE', ( 0.4415831003499929852, -0.9994927481818659531, 0.8299999999999999600 ) ) ; +#84365 = FILL_AREA_STYLE_COLOUR ( '', #25826 ) ; +#84366 = FACE_OUTER_BOUND ( 'NONE', #29164, .T. ) ; +#84367 = PRODUCT_DEFINITION ( 'δ֪', '', #51883, #8458 ) ; +#84368 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#84369 = CARTESIAN_POINT ( 'NONE', ( 1.157511986614658372, 1.258646575926970046, 0.8299999999999999600 ) ) ; +#84370 = FILL_AREA_STYLE_COLOUR ( '', #68680 ) ; +#84371 = EDGE_LOOP ( 'NONE', ( #5066, #88758, #23566, #98953 ) ) ; +#84372 = ORIENTED_EDGE ( 'NONE', *, *, #11878, .T. ) ; +#84373 = VECTOR ( 'NONE', #62182, 1000.000000000000000 ) ; +#84374 = EDGE_CURVE ( 'NONE', #90693, #19897, #87679, .T. ) ; +#84376 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#84375 = LINE ( 'NONE', #61921, #70240 ) ; +#84377 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84378 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42052 ) ) ; +#84379 = STYLED_ITEM ( 'NONE', ( #97174 ), #91268 ) ; +#84380 = PRESENTATION_STYLE_ASSIGNMENT (( #76212 ) ) ; +#84381 = VERTEX_POINT ( 'NONE', #42240 ) ; +#84382 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8991599999999999593 ) ) ; +#84383 = EDGE_CURVE ( 'NONE', #99548, #45151, #17708, .T. ) ; +#84384 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58351 ), #12524 ) ; +#84385 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#84386 = SURFACE_STYLE_USAGE ( .BOTH. , #90546 ) ; +#84387 = PRESENTATION_STYLE_ASSIGNMENT (( #52765 ) ) ; +#84388 = SURFACE_STYLE_USAGE ( .BOTH. , #98618 ) ; +#84389 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#84390 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84391 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#84392 = EDGE_CURVE ( 'NONE', #79801, #79084, #8979, .T. ) ; +#84393 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84394 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85162 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21790, #61130, #85078 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84395 = FACE_OUTER_BOUND ( 'NONE', #4359, .T. ) ; +#84396 = VECTOR ( 'NONE', #49247, 1000.000000000000000 ) ; +#84397 = LINE ( 'NONE', #14402, #61761 ) ; +#84398 = VERTEX_POINT ( 'NONE', #25920 ) ; +#84399 = SURFACE_SIDE_STYLE ('',( #15936 ) ) ; +#84400 = ADVANCED_FACE ( 'NONE', ( #79529 ), #33580, .T. ) ; +#84401 = ORIENTED_EDGE ( 'NONE', *, *, #56347, .T. ) ; +#84402 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8299999999999999600 ) ) ; +#84403 = SURFACE_STYLE_USAGE ( .BOTH. , #31788 ) ; +#84404 = FILL_AREA_STYLE_COLOUR ( '', #10529 ) ; +#84405 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35234 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98045, #12778, #52674 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84406 = FILL_AREA_STYLE_COLOUR ( '', #71705 ) ; +#84407 = STYLED_ITEM ( 'NONE', ( #92319 ), #23270 ) ; +#84408 = LINE ( 'NONE', #38959, #91215 ) ; +#84409 = LINE ( 'NONE', #92060, #11752 ) ; +#84410 = CLOSED_SHELL ( 'NONE', ( #68519, #17475, #55854, #21297, #94998, #65696 ) ) ; +#84411 = EDGE_LOOP ( 'NONE', ( #77037, #66310, #38977, #52158 ) ) ; +#84412 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84413 = AXIS2_PLACEMENT_3D ( 'NONE', #66431, #20971, #52138 ) ; +#84414 = VECTOR ( 'NONE', #3570, 1000.000000000000000 ) ; +#84415 = LINE ( 'NONE', #14422, #96477 ) ; +#84416 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84417 = ORIENTED_EDGE ( 'NONE', *, *, #38791, .T. ) ; +#84419 = CARTESIAN_POINT ( 'NONE', ( 0.7551745129870131024, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#84418 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84420 = ADVANCED_FACE ( 'NONE', ( #57076 ), #65199, .T. ) ; +#84421 = LINE ( 'NONE', #14927, #51779 ) ; +#84422 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#84423 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59980 ) ) ; +#84424 = FILL_AREA_STYLE_COLOUR ( '', #81695 ) ; +#84425 = FACE_OUTER_BOUND ( 'NONE', #78659, .T. ) ; +#84426 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84427 = VERTEX_POINT ( 'NONE', #34088 ) ; +#84428 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95773 ) ) ; +#84429 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84430 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84431 = SURFACE_SIDE_STYLE ('',( #40897 ) ) ; +#84432 = MANIFOLD_SOLID_BREP ( 'ÊäÈë69', #72983 ) ; +#84433 = EDGE_LOOP ( 'NONE', ( #65993, #54598, #9790, #98051 ) ) ; +#84434 = EDGE_CURVE ( 'NONE', #35664, #33464, #9493, .T. ) ; +#84435 = PLANE ( 'NONE', #57906 ) ; +#84436 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#84437 = AXIS2_PLACEMENT_3D ( 'NONE', #76637, #37846, #61362 ) ; +#84438 = FILL_AREA_STYLE_COLOUR ( '', #55344 ) ; +#84439 = AXIS2_PLACEMENT_3D ( 'NONE', #50272, #25758, #72709 ) ; +#84440 = ORIENTED_EDGE ( 'NONE', *, *, #93835, .F. ) ; +#84441 = EDGE_CURVE ( 'NONE', #47689, #98893, #95298, .T. ) ; +#84442 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84443 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18559, 'distance_accuracy_value', 'NONE'); +#84444 = ORIENTED_EDGE ( 'NONE', *, *, #73119, .F. ) ; +#84446 = VERTEX_POINT ( 'NONE', #11489 ) ; +#84445 = LINE ( 'NONE', #15474, #55820 ) ; +#84447 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84448 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #575, 'distance_accuracy_value', 'NONE'); +#84449 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84450 = SURFACE_STYLE_FILL_AREA ( #60006 ) ; +#84451 = LINE ( 'NONE', #31838, #99227 ) ; +#84452 = ORIENTED_EDGE ( 'NONE', *, *, #74555, .T. ) ; +#84453 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.549999999999999822, 0.000000000000000000 ) ) ; +#84454 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84455 = EDGE_LOOP ( 'NONE', ( #97731, #31861, #88715, #63281 ) ) ; +#84456 = AXIS2_PLACEMENT_3D ( 'NONE', #82172, #4036, #82654 ) ; +#84457 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8648700000000000276 ) ) ; +#84458 = EDGE_CURVE ( 'NONE', #92216, #37634, #44704, .T. ) ; +#84459 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84460 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84461 = ORIENTED_EDGE ( 'NONE', *, *, #61939, .F. ) ; +#84462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71430 ), #30649 ) ; +#84464 = CARTESIAN_POINT ( 'NONE', ( 9.780258999999999148, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#84463 = PLANE ( 'NONE', #76327 ) ; +#84465 = VERTEX_POINT ( 'NONE', #50915 ) ; +#84466 = STYLED_ITEM ( 'NONE', ( #89624 ), #17147 ) ; +#84467 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84468 = LINE ( 'NONE', #53834, #84855 ) ; +#84470 = EDGE_CURVE ( 'NONE', #35538, #21063, #46384, .T. ) ; +#84469 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#84471 = CARTESIAN_POINT ( 'NONE', ( 0.3050025479630040226, -1.260362508506799983, 0.8299999999999982947 ) ) ; +#84472 = ORIENTED_EDGE ( 'NONE', *, *, #59865, .F. ) ; +#84474 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45307 ), #48650 ) ; +#84473 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84475 = VERTEX_POINT ( 'NONE', #27415 ) ; +#84476 = PLANE ( 'NONE', #87635 ) ; +#84477 = CLOSED_SHELL ( 'NONE', ( #95455, #60554, #59098, #88485, #59415, #37778 ) ) ; +#84479 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84478 = SURFACE_STYLE_USAGE ( .BOTH. , #46144 ) ; +#84480 = CARTESIAN_POINT ( 'NONE', ( -2.616666666666666252, 3.100000000000000533, 0.000000000000000000 ) ) ; +#84481 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95840 ), #81254 ) ; +#84482 = LINE ( 'NONE', #92612, #69947 ) ; +#84483 = CARTESIAN_POINT ( 'NONE', ( 1.328634758872640154, -1.021599245672099920, 0.8100000000000000533 ) ) ; +#84484 = SURFACE_STYLE_USAGE ( .BOTH. , #53351 ) ; +#84485 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96930, #41841, #4517 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84486 = EDGE_LOOP ( 'NONE', ( #59176, #94498, #58246, #29592 ) ) ; +#84487 = LINE ( 'NONE', #14501, #12151 ) ; +#84488 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66564 ), #3024 ) ; +#84489 = EDGE_CURVE ( 'NONE', #74570, #49312, #36092, .T. ) ; +#84491 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84490 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84492 = FILL_AREA_STYLE_COLOUR ( '', #45425 ) ; +#84493 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48848, 'distance_accuracy_value', 'NONE'); +#84495 = MANIFOLD_SOLID_BREP ( 'ÊäÈë10', #28800 ) ; +#84494 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#84496 = STYLED_ITEM ( 'NONE', ( #77061 ), #75627 ) ; +#84497 = VERTEX_POINT ( 'NONE', #67199 ) ; +#84498 = EDGE_CURVE ( 'NONE', #19800, #13680, #27934, .T. ) ; +#84499 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#84500 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84501 = PRESENTATION_STYLE_ASSIGNMENT (( #77859 ) ) ; +#84502 = SURFACE_STYLE_USAGE ( .BOTH. , #90673 ) ; +#84503 = PLANE ( 'NONE', #70951 ) ; +#84504 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16298 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79394, #47228, #94671 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84505 = VECTOR ( 'NONE', #50091, 1000.000000000000000 ) ; +#84506 = ADVANCED_FACE ( 'NONE', ( #73874 ), #58090, .T. ) ; +#84507 = LINE ( 'NONE', #28392, #100441 ) ; +#84508 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#84509 = FILL_AREA_STYLE ('',( #43198 ) ) ; +#84510 = FACE_OUTER_BOUND ( 'NONE', #54588, .T. ) ; +#84511 = VECTOR ( 'NONE', #19070, 1000.000000000000000 ) ; +#84512 = DIRECTION ( 'NONE', ( 0.7071067811865554553, -0.7071067811865395791, 0.000000000000000000 ) ) ; +#84513 = PRESENTATION_STYLE_ASSIGNMENT (( #84025 ) ) ; +#84514 = SURFACE_STYLE_USAGE ( .BOTH. , #36580 ) ; +#84515 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#84516 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84517 = ADVANCED_FACE ( 'NONE', ( #51909 ), #20229, .T. ) ; +#84518 = AXIS2_PLACEMENT_3D ( 'NONE', #53190, #22536, #14324 ) ; +#84519 = VECTOR ( 'NONE', #17466, 999.9999999999998863 ) ; +#84520 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84521 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#84522 = SURFACE_SIDE_STYLE ('',( #30902 ) ) ; +#84523 = DIRECTION ( 'NONE', ( 0.7071075504167430026, -0.7071060119555152568, 0.000000000000000000 ) ) ; +#84525 = EDGE_CURVE ( 'NONE', #11881, #4927, #45195, .T. ) ; +#84524 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84526 = ORIENTED_EDGE ( 'NONE', *, *, #34882, .T. ) ; +#84527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#84528 = PLANE ( 'NONE', #21004 ) ; +#84529 = VERTEX_POINT ( 'NONE', #38083 ) ; +#84530 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, -3.099999999999995204, -0.02000000000000000042 ) ) ; +#84531 = ADVANCED_FACE ( 'NONE', ( #77362 ), #52915, .F. ) ; +#84532 = ADVANCED_FACE ( 'NONE', ( #31417 ), #84041, .T. ) ; +#84533 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8991599999999999593 ) ) ; +#84534 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16009 ), #86140 ) ; +#84535 = VECTOR ( 'NONE', #88060, 1000.000000000000114 ) ; +#84536 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84537 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84538 = EDGE_LOOP ( 'NONE', ( #100473, #57366, #100817, #6973 ) ) ; +#84539 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -1.500000000000000222, 0.8100000000000000533 ) ) ; +#84540 = EDGE_CURVE ( 'NONE', #31320, #44979, #53397, .T. ) ; +#84541 = EDGE_CURVE ( 'NONE', #66888, #99316, #30909, .T. ) ; +#84542 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25912 ) ) ; +#84543 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6057, 'distance_accuracy_value', 'NONE'); +#84544 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999995004, 0.8200000000000000622, 0.04999999999999997502 ) ) ; +#84545 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16089 ) ) ; +#84546 = VERTEX_POINT ( 'NONE', #14544 ) ; +#84547 = EDGE_LOOP ( 'NONE', ( #85599, #46278, #4383, #1721 ) ) ; +#84548 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#84549 = ORIENTED_EDGE ( 'NONE', *, *, #8928, .T. ) ; +#84550 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#84551 = CARTESIAN_POINT ( 'NONE', ( 0.08473270080998969445, -1.389761831846570095, 0.8299999999999999600 ) ) ; +#84552 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30749 ) ) ; +#84553 = SURFACE_SIDE_STYLE ('',( #30937 ) ) ; +#84554 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84555 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#84556 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.383333333333320425, 1.747825839084689943E-76 ) ) ; +#84557 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90320 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11480, #89685, #37084 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84558 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #39815, #8263 ) ; +#84559 = CARTESIAN_POINT ( 'NONE', ( 0.8552619866146550232, 0.5686465759269649922, 0.8100000000000000533 ) ) ; +#84560 = ORIENTED_EDGE ( 'NONE', *, *, #57857, .T. ) ; +#84561 = ORIENTED_EDGE ( 'NONE', *, *, #93525, .T. ) ; +#84562 = LINE ( 'NONE', #55841, #70334 ) ; +#84563 = FILL_AREA_STYLE ('',( #12544 ) ) ; +#84564 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76483, 'distance_accuracy_value', 'NONE'); +#84565 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, -0.1444665087776849932, 0.8000000000000000444 ) ) ; +#84567 = SURFACE_STYLE_USAGE ( .BOTH. , #99307 ) ; +#84566 = PLANE ( 'NONE', #18240 ) ; +#84568 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#84569 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84570 = SURFACE_SIDE_STYLE ('',( #76923 ) ) ; +#84571 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73167 ), #35645 ) ; +#84573 = VERTEX_POINT ( 'NONE', #6835 ) ; +#84572 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14426 ), #40589 ) ; +#84575 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000059508, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#84574 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84576 = ORIENTED_EDGE ( 'NONE', *, *, #32793, .T. ) ; +#84577 = EDGE_LOOP ( 'NONE', ( #34018, #12925, #98073, #87995 ) ) ; +#84578 = CARTESIAN_POINT ( 'NONE', ( 1.338535375846370057, -1.276477384597439979, 0.8100000000000000533 ) ) ; +#84579 = VECTOR ( 'NONE', #29851, 1000.000000000000000 ) ; +#84580 = STYLED_ITEM ( 'NONE', ( #96419 ), #31536 ) ; +#84582 = FILL_AREA_STYLE ('',( #59659 ) ) ; +#84581 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84583 = FILL_AREA_STYLE ('',( #53466 ) ) ; +#84585 = EDGE_CURVE ( 'NONE', #59144, #92104, #54932, .T. ) ; +#84584 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#84586 = ORIENTED_EDGE ( 'NONE', *, *, #99041, .T. ) ; +#84587 = VECTOR ( 'NONE', #29331, 1000.000000000000000 ) ; +#84588 = SURFACE_STYLE_FILL_AREA ( #23327 ) ; +#84589 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84590 = STYLED_ITEM ( 'NONE', ( #54163 ), #85061 ) ; +#84591 = AXIS2_PLACEMENT_3D ( 'NONE', #69160, #37086, #92174 ) ; +#84592 = PLANE ( 'NONE', #64676 ) ; +#84593 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84594 = VERTEX_POINT ( 'NONE', #77879 ) ; +#84596 = SURFACE_SIDE_STYLE ('',( #5933 ) ) ; +#84595 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#84597 = FACE_OUTER_BOUND ( 'NONE', #69887, .T. ) ; +#84598 = ORIENTED_EDGE ( 'NONE', *, *, #98116, .F. ) ; +#84599 = ADVANCED_FACE ( 'NONE', ( #7848 ), #39085, .F. ) ; +#84600 = EDGE_LOOP ( 'NONE', ( #37534, #83216, #22270, #36916 ) ) ; +#84601 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84603 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84602 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 2.983172999999999853, 0.8991599999999999593 ) ) ; +#84605 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84604 = PRESENTATION_STYLE_ASSIGNMENT (( #37654 ) ) ; +#84606 = MANIFOLD_SOLID_BREP ( 'ÊäÈë138', #74598 ) ; +#84607 = LINE ( 'NONE', #92733, #54818 ) ; +#84608 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84609 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#84610 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47065 ), #61821 ) ; +#84611 = SURFACE_STYLE_FILL_AREA ( #69234 ) ; +#84612 = FILL_AREA_STYLE_COLOUR ( '', #63901 ) ; +#84613 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#84614 = FILL_AREA_STYLE_COLOUR ( '', #27511 ) ; +#84615 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84616 = ORIENTED_EDGE ( 'NONE', *, *, #86397, .T. ) ; +#84617 = VECTOR ( 'NONE', #8842, 1000.000000000000000 ) ; +#84618 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84619 = ORIENTED_EDGE ( 'NONE', *, *, #90652, .T. ) ; +#84620 = EDGE_CURVE ( 'NONE', #5408, #59345, #95686, .T. ) ; +#84621 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84622 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#84623 = CARTESIAN_POINT ( 'NONE', ( -1.114399290982588608, -1.515052199391657028, 0.8099999999996085887 ) ) ; +#84624 = CARTESIAN_POINT ( 'NONE', ( 1.106746768919629975, -1.124851061273939967, 0.8100000000000000533 ) ) ; +#84625 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#84626 = SURFACE_STYLE_FILL_AREA ( #93250 ) ; +#84627 = SURFACE_STYLE_FILL_AREA ( #83132 ) ; +#84628 = VECTOR ( 'NONE', #20432, 1000.000000000000000 ) ; +#84629 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84630 = VERTEX_POINT ( 'NONE', #48785 ) ; +#84631 = SURFACE_STYLE_FILL_AREA ( #53994 ) ; +#84632 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84633 = FILL_AREA_STYLE ('',( #5960 ) ) ; +#84634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84635 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84636 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65039 ) ) ; +#84637 = FACE_OUTER_BOUND ( 'NONE', #59576, .T. ) ; +#84638 = SURFACE_SIDE_STYLE ('',( #61682 ) ) ; +#84639 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84640 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.699999999999999734, 3.364833505069654667E-79 ) ) ; +#84641 = LINE ( 'NONE', #54531, #27229 ) ; +#84642 = CARTESIAN_POINT ( 'NONE', ( -1.144540609093224859, 1.457596776379110004, 0.8299999999999999600 ) ) ; +#84643 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84645 = SURFACE_STYLE_USAGE ( .BOTH. , #29519 ) ; +#84646 = SURFACE_SIDE_STYLE ('',( #37697 ) ) ; +#84647 = ORIENTED_EDGE ( 'NONE', *, *, #98871, .F. ) ; +#84648 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84649 = SURFACE_SIDE_STYLE ('',( #75991 ) ) ; +#84650 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18323 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82543, #91673, #36087 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84651 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69991 ) ) ; +#84652 = CARTESIAN_POINT ( 'NONE', ( 1.157672014548020378, -1.142792474433961480, 0.8099999999999000222 ) ) ; +#84653 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4407 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75790, #35517, #75302 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84654 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45481 ), #65070 ) ; +#84655 = SURFACE_STYLE_USAGE ( .BOTH. , #61211 ) ; +#84656 = ORIENTED_EDGE ( 'NONE', *, *, #1349, .F. ) ; +#84657 = CARTESIAN_POINT ( 'NONE', ( -0.1591923701298700033, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#84658 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84659 = VECTOR ( 'NONE', #39004, 1000.000000000000000 ) ; +#84660 = SURFACE_STYLE_USAGE ( .BOTH. , #53538 ) ; +#84662 = EDGE_CURVE ( 'NONE', #39853, #14049, #18603, .T. ) ; +#84661 = MANIFOLD_SOLID_BREP ( 'ÊäÈë115', #82752 ) ; +#84663 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37464 ), #1604 ) ; +#84664 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91230 ), #92786 ) ; +#84665 = FILL_AREA_STYLE ('',( #83182 ) ) ; +#84666 = AXIS2_PLACEMENT_3D ( 'NONE', #17694, #18702, #57067 ) ; +#84667 = SURFACE_STYLE_FILL_AREA ( #71365 ) ; +#84668 = STYLED_ITEM ( 'NONE', ( #30931 ), #6287 ) ; +#84669 = VERTEX_POINT ( 'NONE', #72748 ) ; +#84670 = ORIENTED_EDGE ( 'NONE', *, *, #76199, .F. ) ; +#84671 = EDGE_CURVE ( 'NONE', #71500, #58386, #44106, .T. ) ; +#84672 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#84673 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12387 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91532, #61431, #92993 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84674 = ORIENTED_EDGE ( 'NONE', *, *, #76104, .T. ) ; +#84675 = FILL_AREA_STYLE_COLOUR ( '', #78900 ) ; +#84676 = LINE ( 'NONE', #6979, #69387 ) ; +#84677 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84678 = CARTESIAN_POINT ( 'NONE', ( 4.847553000000000445, 8.109696999999998823, 0.8991599999999999593 ) ) ; +#84679 = ADVANCED_FACE ( 'NONE', ( #49790 ), #4788, .T. ) ; +#84680 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000002037, 0.4000000000000000222 ) ) ; +#84681 = PRODUCT_CONTEXT ( 'NONE', #34486, 'mechanical' ) ; +#84682 = PLANE ( 'NONE', #5165 ) ; +#84684 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38995 ), #26404 ) ; +#84683 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#84685 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66682 ) ) ; +#84687 = ORIENTED_EDGE ( 'NONE', *, *, #351, .F. ) ; +#84686 = VERTEX_POINT ( 'NONE', #67567 ) ; +#84688 = VECTOR ( 'NONE', #4991, 1000.000000000000000 ) ; +#84689 = ORIENTED_EDGE ( 'NONE', *, *, #1104, .F. ) ; +#84690 = CARTESIAN_POINT ( 'NONE', ( -0.3999999999999990230, 0.2500000000000001110, 0.8499999999999999778 ) ) ; +#84691 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72081, 'distance_accuracy_value', 'NONE'); +#84692 = CARTESIAN_POINT ( 'NONE', ( 1.735855133396799976, -0.9683984092875530525, 0.8300000000000004041 ) ) ; +#84694 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#84693 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#84695 = VECTOR ( 'NONE', #55132, 1000.000000000000000 ) ; +#84696 = ORIENTED_EDGE ( 'NONE', *, *, #84791, .T. ) ; +#84697 = VERTEX_POINT ( 'NONE', #81450 ) ; +#84698 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, 0.2999999999999989897, -0.02000000000002509840 ) ) ; +#84699 = PRESENTATION_STYLE_ASSIGNMENT (( #46373 ) ) ; +#84701 = DIRECTION ( 'NONE', ( -0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#84700 = PRESENTATION_STYLE_ASSIGNMENT (( #78058 ) ) ; +#84702 = CARTESIAN_POINT ( 'NONE', ( -0.3666260071936779941, -1.058874572656040014, 0.8299999999999999600 ) ) ; +#84703 = AXIS2_PLACEMENT_3D ( 'NONE', #25632, #2645, #87898 ) ; +#84704 = ORIENTED_EDGE ( 'NONE', *, *, #30833, .T. ) ; +#84705 = EDGE_LOOP ( 'NONE', ( #39383, #81993, #50660, #53068 ) ) ; +#84706 = VERTEX_POINT ( 'NONE', #42613 ) ; +#84707 = VECTOR ( 'NONE', #11237, 1000.000000000000000 ) ; +#84708 = SURFACE_STYLE_FILL_AREA ( #36754 ) ; +#84709 = CARTESIAN_POINT ( 'NONE', ( 0.01569385388638699919, 1.386208350606499939, 0.8299999999999999600 ) ) ; +#84712 = EDGE_LOOP ( 'NONE', ( #5806, #30153, #82596, #57233 ) ) ; +#84711 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45523 ), #78172 ) ; +#84710 = CYLINDRICAL_SURFACE ( 'NONE', #23372, 0.009999999999999998473 ) ; +#84713 = CARTESIAN_POINT ( 'NONE', ( -2.799999999999999822, 3.000000000000000000, 0.8299999999999999600 ) ) ; +#84714 = ORIENTED_EDGE ( 'NONE', *, *, #29665, .F. ) ; +#84715 = FACE_OUTER_BOUND ( 'NONE', #34651, .T. ) ; +#84716 = FILL_AREA_STYLE ('',( #76547 ) ) ; +#84717 = ORIENTED_EDGE ( 'NONE', *, *, #27198, .T. ) ; +#84718 = ADVANCED_FACE ( 'NONE', ( #67083 ), #81938, .T. ) ; +#84719 = ORIENTED_EDGE ( 'NONE', *, *, #58756, .T. ) ; +#84720 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84721 = STYLED_ITEM ( 'NONE', ( #48276 ), #32688 ) ; +#84722 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#84723 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9659 ) ) ; +#84724 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49631 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20536, #42539, #44508 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84725 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84726 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 2.000000000000000000, -0.02000000000000000042 ) ) ; +#84727 = ORIENTED_EDGE ( 'NONE', *, *, #31573, .T. ) ; +#84728 = CARTESIAN_POINT ( 'NONE', ( 0.4381267573579120111, -1.159910275666830026, 0.8100000000000000533 ) ) ; +#84729 = FILL_AREA_STYLE ('',( #62282 ) ) ; +#84730 = ORIENTED_EDGE ( 'NONE', *, *, #84964, .F. ) ; +#84731 = FILL_AREA_STYLE_COLOUR ( '', #48857 ) ; +#84732 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61951 ) ) ; +#84733 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84734 = STYLED_ITEM ( 'NONE', ( #28657 ), #92355 ) ; +#84735 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.900000000000000133, 0.8299999999999999600 ) ) ; +#84736 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10712 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78826, #1211, #55869 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84737 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#84740 = FILL_AREA_STYLE_COLOUR ( '', #100396 ) ; +#84739 = LINE ( 'NONE', #84249, #31572 ) ; +#84738 = AXIS2_PLACEMENT_3D ( 'NONE', #78873, #3657, #97053 ) ; +#84741 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84742 = PLANE ( 'NONE', #57661 ) ; +#84744 = ADVANCED_FACE ( 'NONE', ( #5261 ), #74760, .T. ) ; +#84743 = SURFACE_STYLE_USAGE ( .BOTH. , #481 ) ; +#84745 = FILL_AREA_STYLE_COLOUR ( '', #60707 ) ; +#84746 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#84747 = FILL_AREA_STYLE_COLOUR ( '', #3931 ) ; +#84748 = VECTOR ( 'NONE', #76096, 1000.000000000000000 ) ; +#84749 = SURFACE_SIDE_STYLE ('',( #46943 ) ) ; +#84750 = SURFACE_STYLE_USAGE ( .BOTH. , #92869 ) ; +#84751 = FACE_OUTER_BOUND ( 'NONE', #65, .T. ) ; +#84753 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#84752 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#84754 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#84755 = SURFACE_SIDE_STYLE ('',( #47977 ) ) ; +#84756 = ORIENTED_EDGE ( 'NONE', *, *, #12645, .F. ) ; +#84757 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, -3.149999999999979927, 0.000000000000000000 ) ) ; +#84758 = ADVANCED_FACE ( 'NONE', ( #13388 ), #92548, .T. ) ; +#84760 = MANIFOLD_SOLID_BREP ( 'ÊäÈë94', #94222 ) ; +#84759 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88151, 'distance_accuracy_value', 'NONE'); +#84761 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #888, 'distance_accuracy_value', 'NONE'); +#84762 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84763 = SURFACE_SIDE_STYLE ('',( #91916 ) ) ; +#84764 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84765 = VECTOR ( 'NONE', #49564, 1000.000000000000000 ) ; +#84766 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 15.15000000000000036, 0.000000000000000000 ) ) ; +#84767 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71751 ), #65250 ) ; +#84768 = VERTEX_POINT ( 'NONE', #77760 ) ; +#84769 = ORIENTED_EDGE ( 'NONE', *, *, #2615, .T. ) ; +#84770 = FILL_AREA_STYLE_COLOUR ( '', #29123 ) ; +#84771 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10745, 'distance_accuracy_value', 'NONE'); +#84772 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43109, 'distance_accuracy_value', 'NONE'); +#84773 = VECTOR ( 'NONE', #98653, 1000.000000000000000 ) ; +#84774 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84775 = CARTESIAN_POINT ( 'NONE', ( -0.1134740259740260049, -0.9623376623376630468, 0.8100000000000000533 ) ) ; +#84776 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84777 = EDGE_CURVE ( 'NONE', #3165, #87351, #76750, .T. ) ; +#84778 = CARTESIAN_POINT ( 'NONE', ( -0.2325713810860060016, -1.366783821657739928, 0.8299999999999995159 ) ) ; +#84779 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.000000000000000000, -12.24500000000000099 ) ) ; +#84780 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84781 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84782 = VERTEX_POINT ( 'NONE', #77243 ) ; +#84783 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84784 = PRESENTATION_STYLE_ASSIGNMENT (( #62852 ) ) ; +#84785 = VERTEX_POINT ( 'NONE', #7720 ) ; +#84786 = FACE_OUTER_BOUND ( 'NONE', #38198, .T. ) ; +#84787 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84788 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84789 = EDGE_LOOP ( 'NONE', ( #79680, #29560, #43733, #15202 ) ) ; +#84790 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#84791 = EDGE_CURVE ( 'NONE', #46606, #69225, #38963, .T. ) ; +#84792 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, 1.149999999999999911 ) ) ; +#84793 = CARTESIAN_POINT ( 'NONE', ( 4.432299999999999685, 10.48512000000000022, 0.8991599999999999593 ) ) ; +#84794 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#84795 = CARTESIAN_POINT ( 'NONE', ( 0.4009334415584410172, -1.279017857142860093, 0.8100000000000001643 ) ) ; +#84796 = CARTESIAN_POINT ( 'NONE', ( 0.1681119866146560116, 0.5791465759269650571, 0.8100000000000001643 ) ) ; +#84798 = ORIENTED_EDGE ( 'NONE', *, *, #75212, .F. ) ; +#84797 = ORIENTED_EDGE ( 'NONE', *, *, #31524, .F. ) ; +#84799 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60365 ) ) ; +#84800 = CARTESIAN_POINT ( 'NONE', ( 1.157511986614659705, 1.258646575926970934, 0.8100000000000000533 ) ) ; +#84801 = ORIENTED_EDGE ( 'NONE', *, *, #2286, .F. ) ; +#84802 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55774 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5089, #27635, #98468 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84803 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84805 = CARTESIAN_POINT ( 'NONE', ( -0.4484892475557449854, -1.042938524989579951, 0.8299999999999999600 ) ) ; +#84804 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#84806 = ORIENTED_EDGE ( 'NONE', *, *, #50354, .T. ) ; +#84807 = ORIENTED_EDGE ( 'NONE', *, *, #83364, .F. ) ; +#84808 = STYLED_ITEM ( 'NONE', ( #167 ), #6548 ) ; +#84809 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84810 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#84811 = PLANE ( 'NONE', #25812 ) ; +#84813 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84812 = PRESENTATION_STYLE_ASSIGNMENT (( #94974 ) ) ; +#84814 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65554 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39291, #78113, #41714 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84815 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#84816 = ORIENTED_EDGE ( 'NONE', *, *, #5371, .T. ) ; +#84817 = EDGE_LOOP ( 'NONE', ( #92850, #20629, #80953, #37461 ) ) ; +#84818 = ORIENTED_EDGE ( 'NONE', *, *, #9423, .F. ) ; +#84819 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90043 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100319, #72308, #80498 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84820 = STYLED_ITEM ( 'NONE', ( #81031 ), #1654 ) ; +#84821 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89720 ) ) ; +#84822 = ORIENTED_EDGE ( 'NONE', *, *, #59377, .F. ) ; +#84823 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 1.050000000000000044, -0.02000000000000000042 ) ) ; +#84824 = FILL_AREA_STYLE_COLOUR ( '', #23810 ) ; +#84825 = CARTESIAN_POINT ( 'NONE', ( 8.800279166500082795, 6.264147833499761120, 0.8991599999999999593 ) ) ; +#84826 = DIRECTION ( 'NONE', ( -0.7071067811865514585, 0.7071067811865435759, 0.000000000000000000 ) ) ; +#84827 = ORIENTED_EDGE ( 'NONE', *, *, #87919, .F. ) ; +#84828 = LINE ( 'NONE', #77173, #14120 ) ; +#84829 = FACE_OUTER_BOUND ( 'NONE', #18784, .T. ) ; +#84830 = ORIENTED_EDGE ( 'NONE', *, *, #40638, .F. ) ; +#84831 = ADVANCED_FACE ( 'NONE', ( #44580 ), #62469, .T. ) ; +#84832 = FILL_AREA_STYLE ('',( #60888 ) ) ; +#84833 = FACE_OUTER_BOUND ( 'NONE', #33837, .T. ) ; +#84834 = ORIENTED_EDGE ( 'NONE', *, *, #61900, .F. ) ; +#84835 = CIRCLE ( 'NONE', #3385, 0.01000000000000002623 ) ; +#84836 = CARTESIAN_POINT ( 'NONE', ( 2.676179938779915002, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#84838 = CARTESIAN_POINT ( 'NONE', ( 1.578229014142009889, -1.479722134560319979, 0.8100000000000000533 ) ) ; +#84837 = LINE ( 'NONE', #99577, #100066 ) ; +#84839 = CARTESIAN_POINT ( 'NONE', ( -0.9589004926578081900, -1.224522408316681688, 0.8099999999998225286 ) ) ; +#84840 = FACE_OUTER_BOUND ( 'NONE', #88359, .T. ) ; +#84841 = DIRECTION ( 'NONE', ( 0.7071067811865470176, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#84842 = VERTEX_POINT ( 'NONE', #644 ) ; +#84843 = CARTESIAN_POINT ( 'NONE', ( 10.34780700000000131, 12.25592199999999998, 0.8991599999999999593 ) ) ; +#84844 = PRESENTATION_STYLE_ASSIGNMENT (( #83864 ) ) ; +#84845 = CARTESIAN_POINT ( 'NONE', ( 0.4656308297546359887, -1.047495427385189970, 0.8299999999999999600 ) ) ; +#84846 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8991599999999999593 ) ) ; +#84847 = SURFACE_STYLE_FILL_AREA ( #61415 ) ; +#84848 = SURFACE_STYLE_USAGE ( .BOTH. , #30720 ) ; +#84849 = EDGE_CURVE ( 'NONE', #7367, #91942, #79797, .T. ) ; +#84850 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4965 ), #94623 ) ; +#84851 = VERTEX_POINT ( 'NONE', #47114 ) ; +#84852 = EDGE_CURVE ( 'NONE', #10551, #43378, #8235, .T. ) ; +#84853 = EDGE_CURVE ( 'NONE', #96015, #54031, #86948, .T. ) ; +#84854 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#84855 = VECTOR ( 'NONE', #14974, 1000.000000000000000 ) ; +#84856 = AXIS2_PLACEMENT_3D ( 'NONE', #77815, #77305, #55382 ) ; +#84857 = ORIENTED_EDGE ( 'NONE', *, *, #93835, .T. ) ; +#84858 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63934 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44302, #73975, #12608 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84859 = SURFACE_STYLE_USAGE ( .BOTH. , #38923 ) ; +#84860 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.95742000000000083, 0.8991599999999999593 ) ) ; +#84861 = LINE ( 'NONE', #14885, #27719 ) ; +#84862 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50833 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44763, #6429, #46257 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84863 = LINE ( 'NONE', #39414, #668 ) ; +#84864 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #32959 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6256, #37488, #23164 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84865 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4982 ) ) ; +#84866 = SURFACE_SIDE_STYLE ('',( #93511 ) ) ; +#84867 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19666 ) ) ; +#84868 = ORIENTED_EDGE ( 'NONE', *, *, #18901, .T. ) ; +#84869 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84870 = EDGE_CURVE ( 'NONE', #81133, #18845, #16961, .T. ) ; +#84871 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#84872 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8199999999999999512 ) ) ; +#84873 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#84874 = EDGE_CURVE ( 'NONE', #33248, #20389, #87938, .T. ) ; +#84875 = FILL_AREA_STYLE ('',( #46033 ) ) ; +#84876 = FILL_AREA_STYLE_COLOUR ( '', #42818 ) ; +#84877 = LINE ( 'NONE', #99117, #30635 ) ; +#84878 = SURFACE_STYLE_USAGE ( .BOTH. , #38440 ) ; +#84879 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -11.57000000000000028 ) ) ; +#84880 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#84881 = PRESENTATION_STYLE_ASSIGNMENT (( #36443 ) ) ; +#84882 = SURFACE_SIDE_STYLE ('',( #38941 ) ) ; +#84883 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23996, 'distance_accuracy_value', 'NONE'); +#84884 = SURFACE_STYLE_USAGE ( .BOTH. , #53756 ) ; +#84885 = AXIS2_PLACEMENT_3D ( 'NONE', #36052, #36553, #74832 ) ; +#84886 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.7000000000000022871, 0.8299999999999999600 ) ) ; +#84887 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23940 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16932, #48631, #71598 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84888 = ORIENTED_EDGE ( 'NONE', *, *, #49643, .F. ) ; +#84889 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.100000000000000089, 2.617092726158356351E-79 ) ) ; +#84890 = ORIENTED_EDGE ( 'NONE', *, *, #74363, .T. ) ; +#84891 = FILL_AREA_STYLE ('',( #37947 ) ) ; +#84893 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71174, 'distance_accuracy_value', 'NONE'); +#84892 = VECTOR ( 'NONE', #39628, 1000.000000000000000 ) ; +#84894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52955, 'distance_accuracy_value', 'NONE'); +#84895 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#84896 = FILL_AREA_STYLE_COLOUR ( '', #8653 ) ; +#84897 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84898 = CARTESIAN_POINT ( 'NONE', ( -0.9882503141469709540, -1.475119686261340046, 0.8299999999999981837 ) ) ; +#84899 = EDGE_CURVE ( 'NONE', #84076, #25543, #82936, .T. ) ; +#84900 = FACE_OUTER_BOUND ( 'NONE', #95658, .T. ) ; +#84901 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.700000000000000178, 0.000000000000000000 ) ) ; +#84902 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333319537, -0.9000000000000001332, 0.000000000000000000 ) ) ; +#84903 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#84904 = ORIENTED_EDGE ( 'NONE', *, *, #83009, .F. ) ; +#84905 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84906 = PLANE ( 'NONE', #95397 ) ; +#84907 = EDGE_CURVE ( 'NONE', #14484, #64865, #62979, .T. ) ; +#84908 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25740, 'distance_accuracy_value', 'NONE'); +#84909 = SURFACE_STYLE_USAGE ( .BOTH. , #92551 ) ; +#84910 = CARTESIAN_POINT ( 'NONE', ( -0.1096996753246760048, -1.219480519480520053, 0.8099999999999796252 ) ) ; +#84911 = VECTOR ( 'NONE', #47730, 1000.000000000000000 ) ; +#84912 = VERTEX_POINT ( 'NONE', #2186 ) ; +#84913 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#84914 = STYLED_ITEM ( 'NONE', ( #48162 ), #10295 ) ; +#84915 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#84916 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999919746 ) ) ; +#84917 = EDGE_CURVE ( 'NONE', #59682, #52091, #9747, .T. ) ; +#84918 = FILL_AREA_STYLE_COLOUR ( '', #84007 ) ; +#84919 = VERTEX_POINT ( 'NONE', #17966 ) ; +#84920 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96950 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4425, #80188, #94947 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84921 = FILL_AREA_STYLE ('',( #68082 ) ) ; +#84922 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22084, 'distance_accuracy_value', 'NONE'); +#84923 = SURFACE_STYLE_FILL_AREA ( #86449 ) ; +#84924 = SURFACE_SIDE_STYLE ('',( #67585 ) ) ; +#84925 = MANIFOLD_SOLID_BREP ( 'ÊäÈë137', #51856 ) ; +#84926 = ORIENTED_EDGE ( 'NONE', *, *, #96692, .F. ) ; +#84927 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84928 = STYLED_ITEM ( 'NONE', ( #73278 ), #33594 ) ; +#84929 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#84930 = FILL_AREA_STYLE_COLOUR ( '', #10737 ) ; +#84931 = ORIENTED_EDGE ( 'NONE', *, *, #72353, .T. ) ; +#84932 = PLANE ( 'NONE', #62995 ) ; +#84933 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100949 ) ; +#84934 = ORIENTED_EDGE ( 'NONE', *, *, #36527, .F. ) ; +#84935 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#84936 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80271 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96178, #40590, #95159 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84937 = EDGE_CURVE ( 'NONE', #36372, #54301, #40494, .T. ) ; +#84938 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31166 ), #86566 ) ; +#84939 = EDGE_LOOP ( 'NONE', ( #85416, #100012, #97711, #6768 ) ) ; +#84941 = ORIENTED_EDGE ( 'NONE', *, *, #10924, .F. ) ; +#84940 = CARTESIAN_POINT ( 'NONE', ( -1.144540609093224859, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#84942 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55693 ) ) ; +#84943 = CARTESIAN_POINT ( 'NONE', ( -0.1711130133853430157, 2.469409075926966679, 0.8299999999999999600 ) ) ; +#84944 = FACE_OUTER_BOUND ( 'NONE', #19313, .T. ) ; +#84945 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#84946 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84947 = EDGE_LOOP ( 'NONE', ( #41887, #96613, #17718, #23399 ) ) ; +#84948 = SURFACE_SIDE_STYLE ('',( #13426 ) ) ; +#84949 = FACE_OUTER_BOUND ( 'NONE', #71197, .T. ) ; +#84950 = EDGE_LOOP ( 'NONE', ( #53595, #89704, #42530, #99112 ) ) ; +#84951 = EDGE_CURVE ( 'NONE', #1435, #69981, #45108, .T. ) ; +#84952 = AXIS2_PLACEMENT_3D ( 'NONE', #62501, #85957, #15477 ) ; +#84953 = FILL_AREA_STYLE ('',( #99191 ) ) ; +#84954 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4849999999999999867, -0.2399999999999999911 ) ) ; +#84955 = ORIENTED_EDGE ( 'NONE', *, *, #56011, .F. ) ; +#84956 = ADVANCED_FACE ( 'NONE', ( #3178 ), #88955, .T. ) ; +#84958 = FILL_AREA_STYLE ('',( #91127 ) ) ; +#84957 = FILL_AREA_STYLE ('',( #45125 ) ) ; +#84959 = ORIENTED_EDGE ( 'NONE', *, *, #98209, .T. ) ; +#84960 = STYLED_ITEM ( 'NONE', ( #30733 ), #64901 ) ; +#84961 = FILL_AREA_STYLE ('',( #77814 ) ) ; +#84962 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54581 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65952, #35338, #95536 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84964 = EDGE_CURVE ( 'NONE', #74684, #92697, #90444, .T. ) ; +#84963 = LINE ( 'NONE', #45619, #32714 ) ; +#84965 = ORIENTED_EDGE ( 'NONE', *, *, #85253, .F. ) ; +#84966 = SURFACE_STYLE_FILL_AREA ( #76301 ) ; +#84967 = EDGE_LOOP ( 'NONE', ( #81625, #31797, #88550, #43560, #62171, #98206, #67595, #90217, #96207, #41120 ) ) ; +#84968 = PRESENTATION_STYLE_ASSIGNMENT (( #7781 ) ) ; +#84969 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84970 = SURFACE_STYLE_USAGE ( .BOTH. , #40564 ) ; +#84971 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, 0.1400000000000000133 ) ) ; +#84972 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63098, 'distance_accuracy_value', 'NONE'); +#84973 = VECTOR ( 'NONE', #38678, 1000.000000000000000 ) ; +#84974 = PLANE ( 'NONE', #98069 ) ; +#84975 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84976 = CIRCLE ( 'NONE', #96342, 0.01902760257185397846 ) ; +#84979 = EDGE_CURVE ( 'NONE', #61665, #55510, #98036, .T. ) ; +#84978 = PRESENTATION_STYLE_ASSIGNMENT (( #62543 ) ) ; +#84977 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11523 ), #89878 ) ; +#84980 = FACE_OUTER_BOUND ( 'NONE', #41130, .T. ) ; +#84981 = ORIENTED_EDGE ( 'NONE', *, *, #87997, .F. ) ; +#84982 = CARTESIAN_POINT ( 'NONE', ( -1.289672647804670058, -1.082231071007949907, 0.8300000000000002931 ) ) ; +#84983 = SURFACE_STYLE_FILL_AREA ( #46154 ) ; +#84985 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.1600000000000000033, -1.250000000000000000 ) ) ; +#84984 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84986 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#84987 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73508 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64601, #33475, #95704 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#84988 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#84990 = MANIFOLD_SOLID_BREP ( 'ÊäÈë135', #38789 ) ; +#84989 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#84991 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#84992 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, -0.02000000000001050243 ) ) ; +#84993 = SURFACE_STYLE_USAGE ( .BOTH. , #93124 ) ; +#84994 = ORIENTED_EDGE ( 'NONE', *, *, #52405, .T. ) ; +#84995 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#84996 = ADVANCED_FACE ( 'NONE', ( #73634 ), #3672, .F. ) ; +#84997 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#84998 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#84999 = EDGE_CURVE ( 'NONE', #93078, #24186, #99515, .T. ) ; +#85000 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.500000000000000000, -0.02000000000001260145 ) ) ; +#85001 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85002 = AXIS2_PLACEMENT_3D ( 'NONE', #66418, #89398, #89893 ) ; +#85003 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50689, #7609, #68950 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85004 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.100000000000000089, 0.8299999999999999600 ) ) ; +#85005 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85006 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#85007 = LINE ( 'NONE', #16051, #89785 ) ; +#85008 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85009 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#85010 = PRESENTATION_STYLE_ASSIGNMENT (( #100709 ) ) ; +#85011 = SURFACE_STYLE_FILL_AREA ( #93140 ) ; +#85012 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56804 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55296, #7199, #39947 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85013 = PRESENTATION_STYLE_ASSIGNMENT (( #39068 ) ) ; +#85014 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#85015 = CARTESIAN_POINT ( 'NONE', ( -0.5999999999999999778, 0.1200000000000000094, 0.6500000000000001332 ) ) ; +#85016 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99915, 'distance_accuracy_value', 'NONE'); +#85017 = PLANE ( 'NONE', #17995 ) ; +#85018 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25417, 'distance_accuracy_value', 'NONE'); +#85019 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85020 = ADVANCED_FACE ( 'NONE', ( #36841 ), #69442, .F. ) ; +#85021 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#85022 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#85023 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.1600000000000000033, -1.250000000000000000 ) ) ; +#85024 = FILL_AREA_STYLE_COLOUR ( '', #99764 ) ; +#85025 = ORIENTED_EDGE ( 'NONE', *, *, #97023, .F. ) ; +#85026 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#85027 = AXIS2_PLACEMENT_3D ( 'NONE', #12298, #19540, #59893 ) ; +#85028 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85029 = EDGE_CURVE ( 'NONE', #69748, #37943, #36341, .T. ) ; +#85030 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22496, 'distance_accuracy_value', 'NONE'); +#85031 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.500000000000000000, 0.000000000000000000 ) ) ; +#85032 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28007 ) ) ; +#85033 = VECTOR ( 'NONE', #98887, 1000.000000000000000 ) ; +#85034 = EDGE_LOOP ( 'NONE', ( #76950, #78220, #50077, #14969 ) ) ; +#85035 = PLANE ( 'NONE', #33158 ) ; +#85036 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.898280000000000189, 0.8648700000000000276 ) ) ; +#85037 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60653 ), #73615 ) ; +#85038 = LINE ( 'NONE', #38097, #52096 ) ; +#85040 = EDGE_CURVE ( 'NONE', #61884, #90763, #74835, .T. ) ; +#85039 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.299999999999999822, -0.02000000000000209943 ) ) ; +#85041 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85043 = ORIENTED_EDGE ( 'NONE', *, *, #41718, .T. ) ; +#85042 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #13249 ) ) ; +#85044 = SURFACE_STYLE_USAGE ( .BOTH. , #30389 ) ; +#85045 = PRESENTATION_STYLE_ASSIGNMENT (( #16086 ) ) ; +#85046 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36029, 'distance_accuracy_value', 'NONE'); +#85047 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, 3.149999999999999911, 0.000000000000000000 ) ) ; +#85048 = AXIS2_PLACEMENT_3D ( 'NONE', #98278, #59605, #100237 ) ; +#85049 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.28250199999999914, 0.8648700000000000276 ) ) ; +#85050 = ORIENTED_EDGE ( 'NONE', *, *, #79793, .F. ) ; +#85051 = ORIENTED_EDGE ( 'NONE', *, *, #68757, .T. ) ; +#85052 = FILL_AREA_STYLE_COLOUR ( '', #27650 ) ; +#85053 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85054 = ORIENTED_EDGE ( 'NONE', *, *, #67757, .T. ) ; +#85055 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85056 = CARTESIAN_POINT ( 'NONE', ( 0.4504580075531440242, -1.245164908316749974, 0.8100000000000000533 ) ) ; +#85057 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#85058 = PRESENTATION_STYLE_ASSIGNMENT (( #53932 ) ) ; +#85059 = STYLED_ITEM ( 'NONE', ( #12292 ), #46537 ) ; +#85060 = PLANE ( 'NONE', #78650 ) ; +#85062 = VERTEX_POINT ( 'NONE', #85794 ) ; +#85061 = ADVANCED_FACE ( 'NONE', ( #52664 ), #84298, .T. ) ; +#85063 = ORIENTED_EDGE ( 'NONE', *, *, #15568, .T. ) ; +#85064 = CARTESIAN_POINT ( 'NONE', ( -0.8116113847191938069, 1.501851835025195481, 0.8100000000000000533 ) ) ; +#85066 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#85065 = SURFACE_STYLE_FILL_AREA ( #46229 ) ; +#85067 = ADVANCED_FACE ( 'NONE', ( #10999 ), #64710, .F. ) ; +#85068 = ORIENTED_EDGE ( 'NONE', *, *, #40544, .T. ) ; +#85069 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85070 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79199, #3101, #9164, #2106 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85071 = CARTESIAN_POINT ( 'NONE', ( 0.6425994866146570450, 0.5595340759269650244, 0.8299999999999999600 ) ) ; +#85072 = PLANE ( 'NONE', #56131 ) ; +#85073 = STYLED_ITEM ( 'NONE', ( #9941 ), #18498 ) ; +#85074 = VECTOR ( 'NONE', #99410, 1000.000000000000000 ) ; +#85075 = ORIENTED_EDGE ( 'NONE', *, *, #65183, .F. ) ; +#85076 = EDGE_CURVE ( 'NONE', #3083, #18465, #57596, .T. ) ; +#85078 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85077 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85079 = ORIENTED_EDGE ( 'NONE', *, *, #39693, .T. ) ; +#85080 = VERTEX_POINT ( 'NONE', #80557 ) ; +#85081 = FILL_AREA_STYLE ('',( #46247 ) ) ; +#85082 = VECTOR ( 'NONE', #28728, 1000.000000000000000 ) ; +#85083 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98025 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46954, #78123, #38811 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85084 = AXIS2_PLACEMENT_3D ( 'NONE', #38080, #67197, #5872 ) ; +#85086 = PLANE ( 'NONE', #84219 ) ; +#85085 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#85088 = ADVANCED_FACE ( 'NONE', ( #72360 ), #25938, .T. ) ; +#85087 = DIRECTION ( 'NONE', ( -0.7071045084557425753, 0.7071090539100477468, 0.000000000000000000 ) ) ; +#85090 = VERTEX_POINT ( 'NONE', #78156 ) ; +#85089 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8648700000000000276 ) ) ; +#85091 = AXIS2_PLACEMENT_3D ( 'NONE', #44661, #99692, #65402 ) ; +#85092 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 4.680228999999999751, 0.8991599999999999593 ) ) ; +#85093 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85094 = LINE ( 'NONE', #86098, #15656 ) ; +#85095 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54131 ), #24804 ) ; +#85096 = VERTEX_POINT ( 'NONE', #62342 ) ; +#85097 = ORIENTED_EDGE ( 'NONE', *, *, #66916, .F. ) ; +#85098 = EDGE_LOOP ( 'NONE', ( #64500, #46395, #95675, #74348 ) ) ; +#85099 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.17581999999999987, 0.8991599999999999593 ) ) ; +#85101 = SURFACE_STYLE_FILL_AREA ( #53969 ) ; +#85100 = CARTESIAN_POINT ( 'NONE', ( 1.068987518412940263, -1.485874691073119980, 0.8299999999999999600 ) ) ; +#85102 = PLANE ( 'NONE', #75076 ) ; +#85103 = STYLED_ITEM ( 'NONE', ( #85221 ), #7699 ) ; +#85104 = MANIFOLD_SOLID_BREP ( 'ÊäÈë104', #37131 ) ; +#85105 = PRESENTATION_STYLE_ASSIGNMENT (( #90768 ) ) ; +#85106 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#85107 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999989964, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#85108 = SURFACE_STYLE_FILL_AREA ( #92736 ) ; +#85109 = EDGE_CURVE ( 'NONE', #57506, #33372, #55407, .T. ) ; +#85111 = EDGE_CURVE ( 'NONE', #81798, #66903, #28917, .T. ) ; +#85110 = FILL_AREA_STYLE_COLOUR ( '', #94914 ) ; +#85112 = EDGE_LOOP ( 'NONE', ( #52737, #60259, #67463, #48671 ) ) ; +#85113 = SURFACE_STYLE_FILL_AREA ( #343 ) ; +#85114 = VERTEX_POINT ( 'NONE', #60110 ) ; +#85115 = PLANE ( 'NONE', #58785 ) ; +#85116 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 2.500000000000000000, 8.977651093538432215E-153 ) ) ; +#85117 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85118 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85119 = PLANE ( 'NONE', #2834 ) ; +#85120 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85121 = FACE_OUTER_BOUND ( 'NONE', #67756, .T. ) ; +#85122 = ORIENTED_EDGE ( 'NONE', *, *, #16225, .F. ) ; +#85123 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85124 = FILL_AREA_STYLE ('',( #99353 ) ) ; +#85125 = EDGE_CURVE ( 'NONE', #34880, #58245, #6401, .T. ) ; +#85126 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85127 = FILL_AREA_STYLE ('',( #77461 ) ) ; +#85128 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74463, 'distance_accuracy_value', 'NONE'); +#85129 = EDGE_CURVE ( 'NONE', #2107, #25343, #44227, .T. ) ; +#85130 = STYLED_ITEM ( 'NONE', ( #41910 ), #46830 ) ; +#85131 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85132 = SURFACE_STYLE_USAGE ( .BOTH. , #6466 ) ; +#85133 = CARTESIAN_POINT ( 'NONE', ( -0.9337505133853429840, 2.302534075926970125, 0.8100000000000000533 ) ) ; +#85134 = FILL_AREA_STYLE ('',( #22875 ) ) ; +#85135 = SURFACE_SIDE_STYLE ('',( #44309 ) ) ; +#85136 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2002 ) ) ; +#85137 = VECTOR ( 'NONE', #14816, 1000.000000000000000 ) ; +#85138 = SURFACE_STYLE_FILL_AREA ( #98985 ) ; +#85139 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85140 = DIRECTION ( 'NONE', ( -0.01414952675146895558, -0.9998998904353922912, 0.000000000000000000 ) ) ; +#85141 = ORIENTED_EDGE ( 'NONE', *, *, #85578, .T. ) ; +#85142 = PLANE ( 'NONE', #59315 ) ; +#85143 = SURFACE_STYLE_FILL_AREA ( #92773 ) ; +#85144 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#85145 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85146 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78812, 'distance_accuracy_value', 'NONE'); +#85147 = DIRECTION ( 'NONE', ( -0.7071067811865470176, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#85148 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#85149 = AXIS2_PLACEMENT_3D ( 'NONE', #69217, #40033, #71168 ) ; +#85150 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80308 ), #93289 ) ; +#85151 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#85152 = FILL_AREA_STYLE ('',( #69293 ) ) ; +#85153 = ORIENTED_EDGE ( 'NONE', *, *, #80327, .F. ) ; +#85154 = EDGE_CURVE ( 'NONE', #20037, #13569, #43725, .T. ) ; +#85155 = VECTOR ( 'NONE', #33883, 1000.000000000000114 ) ; +#85156 = PRESENTATION_STYLE_ASSIGNMENT (( #61215 ) ) ; +#85157 = AXIS2_PLACEMENT_3D ( 'NONE', #90794, #51522, #19327 ) ; +#85158 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#85159 = MANIFOLD_SOLID_BREP ( 'ÊäÈë83', #90914 ) ; +#85160 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46652, 'distance_accuracy_value', 'NONE'); +#85161 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.7499999999822648533, -0.6999999999948158802 ) ) ; +#85162 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21790, 'distance_accuracy_value', 'NONE'); +#85163 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85164 = EDGE_CURVE ( 'NONE', #27423, #78125, #73893, .T. ) ; +#85165 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#85166 = ORIENTED_EDGE ( 'NONE', *, *, #92893, .F. ) ; +#85167 = ORIENTED_EDGE ( 'NONE', *, *, #344, .T. ) ; +#85168 = SURFACE_STYLE_FILL_AREA ( #70346 ) ; +#85169 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#85170 = ORIENTED_EDGE ( 'NONE', *, *, #42148, .T. ) ; +#85171 = CARTESIAN_POINT ( 'NONE', ( -0.7482130133853427401, 1.552121575926969976, 0.8100000000000000533 ) ) ; +#85172 = VECTOR ( 'NONE', #88096, 1000.000000000000000 ) ; +#85173 = LINE ( 'NONE', #22919, #92328 ) ; +#85174 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #55359 ) ; +#85175 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999996758, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#85178 = ORIENTED_EDGE ( 'NONE', *, *, #17060, .F. ) ; +#85177 = ORIENTED_EDGE ( 'NONE', *, *, #63178, .T. ) ; +#85176 = ADVANCED_FACE ( 'NONE', ( #42740 ), #90710, .F. ) ; +#85179 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23259 ), #80336 ) ; +#85180 = VERTEX_POINT ( 'NONE', #15051 ) ; +#85181 = CARTESIAN_POINT ( 'NONE', ( 1.715954649776489926, -1.507352529807550079, 0.8299999999999999600 ) ) ; +#85182 = ORIENTED_EDGE ( 'NONE', *, *, #72012, .F. ) ; +#85183 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70541 ) ) ; +#85185 = ADVANCED_FACE ( 'NONE', ( #23793 ), #23284, .T. ) ; +#85184 = VERTEX_POINT ( 'NONE', #70739 ) ; +#85186 = SURFACE_SIDE_STYLE ('',( #61251 ) ) ; +#85187 = VECTOR ( 'NONE', #69661, 1000.000000000000000 ) ; +#85188 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626904549, -0.1400000000000000411 ) ) ; +#85189 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999378, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#85190 = ORIENTED_EDGE ( 'NONE', *, *, #41580, .F. ) ; +#85191 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.950000000000000178, 0.000000000000000000 ) ) ; +#85192 = AXIS2_PLACEMENT_3D ( 'NONE', #16741, #47927, #79079 ) ; +#85193 = EDGE_LOOP ( 'NONE', ( #1962, #85153, #65786, #25209 ) ) ; +#85194 = VERTEX_POINT ( 'NONE', #53411 ) ; +#85195 = CARTESIAN_POINT ( 'NONE', ( 0.2732652112985429760, -1.367023653493709912, 0.8300000000000004041 ) ) ; +#85196 = PLANE ( 'NONE', #75484 ) ; +#85198 = ADVANCED_FACE ( 'NONE', ( #69711 ), #99748, .T. ) ; +#85197 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85200 = VERTEX_POINT ( 'NONE', #45702 ) ; +#85199 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.2999999999999990452, 0.000000000000000000 ) ) ; +#85201 = PRESENTATION_STYLE_ASSIGNMENT (( #100413 ) ) ; +#85202 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2849999999999999756, -0.1499999999999999944 ) ) ; +#85203 = AXIS2_PLACEMENT_3D ( 'NONE', #80012, #71836, #49878 ) ; +#85204 = STYLED_ITEM ( 'NONE', ( #95538 ), #35718 ) ; +#85205 = ORIENTED_EDGE ( 'NONE', *, *, #3659, .T. ) ; +#85207 = SURFACE_SIDE_STYLE ('',( #31605 ) ) ; +#85206 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85208 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#85209 = ORIENTED_EDGE ( 'NONE', *, *, #69285, .F. ) ; +#85210 = EDGE_CURVE ( 'NONE', #54301, #74058, #6847, .T. ) ; +#85211 = ORIENTED_EDGE ( 'NONE', *, *, #36463, .F. ) ; +#85212 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85213 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85214 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68872 ), #41237 ) ; +#85215 = AXIS2_PLACEMENT_3D ( 'NONE', #95530, #40962, #608 ) ; +#85216 = AXIS2_PLACEMENT_3D ( 'NONE', #45906, #86253, #37793 ) ; +#85217 = CARTESIAN_POINT ( 'NONE', ( -0.4538159765161179915, -1.241081418093670008, 0.8299999999999999600 ) ) ; +#85218 = VECTOR ( 'NONE', #3621, 1000.000000000000114 ) ; +#85219 = EDGE_CURVE ( 'NONE', #85932, #91804, #30390, .T. ) ; +#85220 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29831 ) ) ; +#85222 = EDGE_CURVE ( 'NONE', #95195, #7270, #17104, .T. ) ; +#85221 = PRESENTATION_STYLE_ASSIGNMENT (( #6557 ) ) ; +#85223 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99139, #5249, #35968, #36452 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 3.286767773152560933E-14, 7.071456398328928379E-05 ), + .UNSPECIFIED. ) ; +#85224 = CARTESIAN_POINT ( 'NONE', ( 1.016962903650600047, -1.153389236204189983, 0.8299999999999997380 ) ) ; +#85225 = AXIS2_PLACEMENT_3D ( 'NONE', #33836, #88438, #34854 ) ; +#85226 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, 0.000000000000000000 ) ) ; +#85227 = CARTESIAN_POINT ( 'NONE', ( 0.1707063580043630124, -1.088378544347549992, 0.8300000000000020695 ) ) ; +#85228 = ORIENTED_EDGE ( 'NONE', *, *, #19531, .T. ) ; +#85229 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85230 = CARTESIAN_POINT ( 'NONE', ( 0.08699603081118000014, -1.280379325981960026, 0.8299999999999999600 ) ) ; +#85231 = ORIENTED_EDGE ( 'NONE', *, *, #63667, .F. ) ; +#85232 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #99659 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80227, #55730, #25107 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85233 = FILL_AREA_STYLE_COLOUR ( '', #59596 ) ; +#85234 = EDGE_CURVE ( 'NONE', #3092, #32857, #34144, .T. ) ; +#85235 = VECTOR ( 'NONE', #39166, 1000.000000000000000 ) ; +#85236 = ADVANCED_FACE ( 'NONE', ( #1300 ), #88572, .T. ) ; +#85238 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66255, 'distance_accuracy_value', 'NONE'); +#85237 = FILL_AREA_STYLE_COLOUR ( '', #54881 ) ; +#85239 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.4999999999999991673, 0.1829999999999789573 ) ) ; +#85240 = AXIS2_PLACEMENT_3D ( 'NONE', #30069, #52094, #37274 ) ; +#85242 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85241 = SURFACE_STYLE_USAGE ( .BOTH. , #475 ) ; +#85243 = LINE ( 'NONE', #76574, #60170 ) ; +#85244 = CARTESIAN_POINT ( 'NONE', ( 1.749115224440590088, -1.150470459123589917, 0.8100000000000000533 ) ) ; +#85245 = PRESENTATION_STYLE_ASSIGNMENT (( #53619 ) ) ; +#85246 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#85247 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#85248 = EDGE_CURVE ( 'NONE', #60913, #57506, #17604, .T. ) ; +#85249 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85250 = VECTOR ( 'NONE', #49662, 1000.000000000000000 ) ; +#85251 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.500000000000000000, -1.195472123049164304E-89 ) ) ; +#85252 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.700000000000000178, 0.1829999999999459837 ) ) ; +#85253 = EDGE_CURVE ( 'NONE', #2862, #14378, #18093, .T. ) ; +#85255 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 4.135756999999999906, 0.8991599999999999593 ) ) ; +#85254 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85256 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85257 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51051 ) ) ; +#85258 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38673, 'distance_accuracy_value', 'NONE'); +#85259 = ORIENTED_EDGE ( 'NONE', *, *, #80307, .T. ) ; +#85260 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999902023, -3.123820061220065281, 0.000000000000000000 ) ) ; +#85261 = FACE_OUTER_BOUND ( 'NONE', #46448, .T. ) ; +#85262 = MANIFOLD_SOLID_BREP ( 'ÊäÈë118', #63164 ) ; +#85263 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85264 = SURFACE_SIDE_STYLE ('',( #54138 ) ) ; +#85265 = FILL_AREA_STYLE ('',( #31158 ) ) ; +#85266 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85267 = FILL_AREA_STYLE_COLOUR ( '', #73609 ) ; +#85268 = PRESENTATION_STYLE_ASSIGNMENT (( #30620 ) ) ; +#85269 = SURFACE_STYLE_FILL_AREA ( #24554 ) ; +#85270 = EDGE_LOOP ( 'NONE', ( #22925, #50474, #49908, #5684 ) ) ; +#85271 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85272 = STYLED_ITEM ( 'NONE', ( #70663 ), #75988 ) ; +#85273 = VERTEX_POINT ( 'NONE', #42133 ) ; +#85274 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#85275 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, -0.02000000000000000042 ) ) ; +#85276 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#85277 = CARTESIAN_POINT ( 'NONE', ( 1.126705527605965873, -0.8904278853685342332, 0.8100000000000586731 ) ) ; +#85278 = SURFACE_SIDE_STYLE ('',( #92905 ) ) ; +#85279 = LINE ( 'NONE', #62336, #20475 ) ; +#85280 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96710 ), #64105 ) ; +#85281 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36407 ), #93342 ) ; +#85282 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85283 = FILL_AREA_STYLE_COLOUR ( '', #36351 ) ; +#85284 = EDGE_CURVE ( 'NONE', #4744, #71358, #80433, .T. ) ; +#85285 = VERTEX_POINT ( 'NONE', #73283 ) ; +#85286 = VECTOR ( 'NONE', #56467, 1000.000000000000000 ) ; +#85287 = CARTESIAN_POINT ( 'NONE', ( 1.121762993838200106, -0.9661431204389000493, 0.8300000000000002931 ) ) ; +#85288 = PLANE ( 'NONE', #80343 ) ; +#85289 = ORIENTED_EDGE ( 'NONE', *, *, #32219, .F. ) ; +#85290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85291 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#85292 = AXIS2_PLACEMENT_3D ( 'NONE', #62756, #72919, #86208 ) ; +#85293 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28248 ) ) ; +#85294 = ORIENTED_EDGE ( 'NONE', *, *, #6090, .T. ) ; +#85295 = VECTOR ( 'NONE', #11618, 1000.000000000000000 ) ; +#85296 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8613 ), #75550 ) ; +#85297 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#85298 = CARTESIAN_POINT ( 'NONE', ( 1.854016048130769923, -1.137681993439920047, 0.8100000000000000533 ) ) ; +#85299 = CARTESIAN_POINT ( 'NONE', ( 0.09926676434810605132, 0.9393705549101529773, 0.8099999999999999423 ) ) ; +#85301 = EDGE_LOOP ( 'NONE', ( #87844, #70523, #59876, #26510 ) ) ; +#85300 = VERTEX_POINT ( 'NONE', #1817 ) ; +#85302 = VECTOR ( 'NONE', #57644, 1000.000000000000000 ) ; +#85303 = STYLED_ITEM ( 'NONE', ( #60556 ), #9178 ) ; +#85304 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85305 = VERTEX_POINT ( 'NONE', #87577 ) ; +#85306 = AXIS2_PLACEMENT_3D ( 'NONE', #27986, #20798, #52457 ) ; +#85308 = CARTESIAN_POINT ( 'NONE', ( -0.4682654858281209975, -1.005282756156510082, 0.8299999999999999600 ) ) ; +#85307 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 3.500000000000000444, 0.000000000000000000 ) ) ; +#85309 = ORIENTED_EDGE ( 'NONE', *, *, #84374, .T. ) ; +#85311 = EDGE_CURVE ( 'NONE', #4592, #61768, #55459, .T. ) ; +#85310 = VERTEX_POINT ( 'NONE', #24314 ) ; +#85312 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85313 = SURFACE_STYLE_USAGE ( .BOTH. , #60868 ) ; +#85314 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36368 ), #2189 ) ; +#85316 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85315 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85317 = FACE_OUTER_BOUND ( 'NONE', #91228, .T. ) ; +#85318 = ORIENTED_EDGE ( 'NONE', *, *, #84917, .T. ) ; +#85319 = VERTEX_POINT ( 'NONE', #90080 ) ; +#85320 = LINE ( 'NONE', #31212, #77883 ) ; +#85321 = ORIENTED_EDGE ( 'NONE', *, *, #38700, .F. ) ; +#85322 = FILL_AREA_STYLE ('',( #77164 ) ) ; +#85323 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33057 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100062, #73327, #89640 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85325 = VERTEX_POINT ( 'NONE', #13401 ) ; +#85324 = FACE_OUTER_BOUND ( 'NONE', #96946, .T. ) ; +#85326 = MANIFOLD_SOLID_BREP ( 'ÊäÈë59', #22457 ) ; +#85327 = SURFACE_STYLE_USAGE ( .BOTH. , #54734 ) ; +#85328 = PLANE ( 'NONE', #25423 ) ; +#85329 = FACE_OUTER_BOUND ( 'NONE', #35741, .T. ) ; +#85330 = VERTEX_POINT ( 'NONE', #74775 ) ; +#85331 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #34702, #41346, #12620, #91296 ), + ( #28515, #29015, #67306, #58690 ), + ( #67793, #98868, #12111, #20344 ), + ( #66324, #83148, #43829, #44310 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243638272, 0.8047378541243638272, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606867492, 0.6476030138606867492, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606867492, 0.6476030138606867492, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243638272, 0.8047378541243638272, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#85332 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85333 = ORIENTED_EDGE ( 'NONE', *, *, #20325, .F. ) ; +#85334 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85335 = FILL_AREA_STYLE_COLOUR ( '', #54694 ) ; +#85336 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2209 ) ) ; +#85337 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#85338 = AXIS2_PLACEMENT_3D ( 'NONE', #76987, #69817, #52518 ) ; +#85340 = ORIENTED_EDGE ( 'NONE', *, *, #13816, .F. ) ; +#85339 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2849999999999999756, 0.000000000000000000 ) ) ; +#85341 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85342 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#85344 = CARTESIAN_POINT ( 'NONE', ( 1.562899685023940055, -1.469666695271939938, 0.8100000000000000533 ) ) ; +#85343 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85345 = FILL_AREA_STYLE_COLOUR ( '', #83358 ) ; +#85346 = FILL_AREA_STYLE ('',( #14359 ) ) ; +#85347 = VECTOR ( 'NONE', #51634, 999.9999999999998863 ) ; +#85348 = LINE ( 'NONE', #40434, #20165 ) ; +#85349 = EDGE_LOOP ( 'NONE', ( #68455, #37009, #6601, #4459 ) ) ; +#85350 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1500000000000000222 ) ) ; +#85351 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #84051, #82064, #28422, #45205 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85352 = FILL_AREA_STYLE_COLOUR ( '', #47958 ) ; +#85353 = EDGE_CURVE ( 'NONE', #5169, #79924, #11391, .T. ) ; +#85354 = SURFACE_SIDE_STYLE ('',( #69515 ) ) ; +#85355 = PLANE ( 'NONE', #69126 ) ; +#85356 = VECTOR ( 'NONE', #61072, 1000.000000000000000 ) ; +#85358 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#85357 = LINE ( 'NONE', #99586, #99890 ) ; +#85360 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77194 ) ) ; +#85359 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85361 = LINE ( 'NONE', #7672, #50022 ) ; +#85362 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#85364 = STYLED_ITEM ( 'NONE', ( #88157 ), #28674 ) ; +#85363 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15434 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87463, #170, #8753 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85365 = AXIS2_PLACEMENT_3D ( 'NONE', #18815, #88284, #18296 ) ; +#85366 = SURFACE_STYLE_USAGE ( .BOTH. , #30722 ) ; +#85367 = CARTESIAN_POINT ( 'NONE', ( 6.212269000000000041, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#85368 = EDGE_LOOP ( 'NONE', ( #27998, #89473, #15447, #36245 ) ) ; +#85369 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85370 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85371 = EDGE_CURVE ( 'NONE', #28255, #31184, #51803, .T. ) ; +#85372 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24021 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84426, #22135, #98655 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85373 = ORIENTED_EDGE ( 'NONE', *, *, #36324, .F. ) ; +#85374 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#85375 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85376 = PLANE ( 'NONE', #47218 ) ; +#85377 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95644, #19578, #25749, #82387 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85378 = PRESENTATION_STYLE_ASSIGNMENT (( #47076 ) ) ; +#85379 = VECTOR ( 'NONE', #16930, 1000.000000000000000 ) ; +#85380 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85381 = STYLED_ITEM ( 'NONE', ( #64635 ), #11714 ) ; +#85382 = ORIENTED_EDGE ( 'NONE', *, *, #97085, .T. ) ; +#85383 = CARTESIAN_POINT ( 'NONE', ( 1.783955832751769943, -0.9153515042605530061, 0.8100000000000008304 ) ) ; +#85384 = FACE_OUTER_BOUND ( 'NONE', #96259, .T. ) ; +#85385 = LINE ( 'NONE', #46571, #60453 ) ; +#85386 = PLANE ( 'NONE', #36335 ) ; +#85387 = LINE ( 'NONE', #63940, #38838 ) ; +#85388 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85389 = CARTESIAN_POINT ( 'NONE', ( 4.409147000000000816, 4.857005000000000017, 0.8991599999999999593 ) ) ; +#85390 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7031 ), #23457 ) ; +#85391 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#85392 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#85393 = CARTESIAN_POINT ( 'NONE', ( 0.06276991512889880387, -1.007076035477679987, 0.8299999999999999600 ) ) ; +#85394 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85395 = ADVANCED_FACE ( 'NONE', ( #83442 ), #5777, .T. ) ; +#85396 = FACE_OUTER_BOUND ( 'NONE', #27469, .T. ) ; +#85397 = SURFACE_STYLE_USAGE ( .BOTH. , #29279 ) ; +#85398 = ORIENTED_EDGE ( 'NONE', *, *, #31499, .F. ) ; +#85399 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85400 = VECTOR ( 'NONE', #40814, 1000.000000000000000 ) ; +#85401 = ORIENTED_EDGE ( 'NONE', *, *, #70601, .F. ) ; +#85402 = CYLINDRICAL_SURFACE ( 'NONE', #19260, 0.05000000000000012768 ) ; +#85403 = SURFACE_STYLE_FILL_AREA ( #78267 ) ; +#85404 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85405 = CARTESIAN_POINT ( 'NONE', ( -1.043371449138229989, -1.500691070757680157, 0.8299999999999981837 ) ) ; +#85406 = DIRECTION ( 'NONE', ( 8.347776819438500435E-49, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85407 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85408 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85409 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#85410 = FILL_AREA_STYLE_COLOUR ( '', #33066 ) ; +#85411 = EDGE_CURVE ( 'NONE', #11607, #99332, #3738, .T. ) ; +#85412 = VERTEX_POINT ( 'NONE', #19120 ) ; +#85413 = CARTESIAN_POINT ( 'NONE', ( 10.21449324974999939, 6.264147750250000257, 0.8991599999999999593 ) ) ; +#85414 = FACE_OUTER_BOUND ( 'NONE', #77374, .T. ) ; +#85415 = SURFACE_STYLE_FILL_AREA ( #38465 ) ; +#85416 = ORIENTED_EDGE ( 'NONE', *, *, #100544, .T. ) ; +#85417 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -0.7000000000000001776, 0.000000000000000000 ) ) ; +#85418 = STYLED_ITEM ( 'NONE', ( #92505 ), #88366 ) ; +#85419 = CARTESIAN_POINT ( 'NONE', ( 0.3666666666666633101, 3.500000000000000000, 0.000000000000000000 ) ) ; +#85420 = EDGE_LOOP ( 'NONE', ( #80607, #57548, #33207, #52453 ) ) ; +#85421 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85422 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69054 ), #20181 ) ; +#85423 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85424 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85425 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#85426 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85427 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85428 = EDGE_LOOP ( 'NONE', ( #60429, #9690, #30610, #26064 ) ) ; +#85429 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85430 = PRESENTATION_STYLE_ASSIGNMENT (( #62483 ) ) ; +#85431 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23501 ), #56166 ) ; +#85432 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53347 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43080, #3784, #57952 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85433 = MANIFOLD_SOLID_BREP ( 'ÊäÈë45', #1111 ) ; +#85434 = ORIENTED_EDGE ( 'NONE', *, *, #75068, .T. ) ; +#85436 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85435 = STYLED_ITEM ( 'NONE', ( #31705 ), #38107 ) ; +#85437 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85438 = LINE ( 'NONE', #77786, #45632 ) ; +#85439 = SURFACE_STYLE_FILL_AREA ( #79820 ) ; +#85440 = SURFACE_STYLE_USAGE ( .BOTH. , #93059 ) ; +#85441 = ORIENTED_EDGE ( 'NONE', *, *, #14315, .T. ) ; +#85442 = ORIENTED_EDGE ( 'NONE', *, *, #52027, .T. ) ; +#85443 = FACE_OUTER_BOUND ( 'NONE', #71502, .T. ) ; +#85444 = EDGE_CURVE ( 'NONE', #90311, #41421, #11883, .T. ) ; +#85445 = EDGE_LOOP ( 'NONE', ( #5822, #95272, #86040, #76504 ) ) ; +#85446 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80597 ) ) ; +#85447 = STYLED_ITEM ( 'NONE', ( #49061 ), #2864 ) ; +#85448 = ORIENTED_EDGE ( 'NONE', *, *, #63863, .F. ) ; +#85450 = ORIENTED_EDGE ( 'NONE', *, *, #29415, .F. ) ; +#85449 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85451 = PLANE ( 'NONE', #75284 ) ; +#85452 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85453 = CARTESIAN_POINT ( 'NONE', ( -1.783856376673197687E-67, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#85454 = STYLED_ITEM ( 'NONE', ( #84699 ), #68712 ) ; +#85455 = ORIENTED_EDGE ( 'NONE', *, *, #19836, .F. ) ; +#85456 = SURFACE_STYLE_FILL_AREA ( #16486 ) ; +#85457 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999918510, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#85458 = FILL_AREA_STYLE_COLOUR ( '', #26475 ) ; +#85459 = ORIENTED_EDGE ( 'NONE', *, *, #36503, .T. ) ; +#85460 = EDGE_CURVE ( 'NONE', #22294, #93113, #70100, .T. ) ; +#85461 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8100000000000610045 ) ) ; +#85462 = EDGE_CURVE ( 'NONE', #27435, #25071, #99163, .T. ) ; +#85463 = FILL_AREA_STYLE ('',( #44630 ) ) ; +#85464 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85465 = VECTOR ( 'NONE', #53669, 1000.000000000000000 ) ; +#85466 = ORIENTED_EDGE ( 'NONE', *, *, #79749, .T. ) ; +#85468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85467 = SURFACE_STYLE_USAGE ( .BOTH. , #47169 ) ; +#85469 = ORIENTED_EDGE ( 'NONE', *, *, #24650, .F. ) ; +#85470 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85471 = PLANE ( 'NONE', #81703 ) ; +#85472 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85473 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85474 = EDGE_CURVE ( 'NONE', #270, #74943, #78296, .T. ) ; +#85475 = ORIENTED_EDGE ( 'NONE', *, *, #81229, .F. ) ; +#85476 = CARTESIAN_POINT ( 'NONE', ( -4.898587196589412459E-17, 0.6700000000000000400, 0.1999999999999999833 ) ) ; +#85477 = ORIENTED_EDGE ( 'NONE', *, *, #6443, .T. ) ; +#85478 = SURFACE_SIDE_STYLE ('',( #54358 ) ) ; +#85480 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85479 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#85481 = SURFACE_SIDE_STYLE ('',( #62537 ) ) ; +#85483 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #69112 ) ) ; +#85482 = FACE_BOUND ( 'NONE', #21498, .T. ) ; +#85484 = AXIS2_PLACEMENT_3D ( 'NONE', #51884, #76336, #76850 ) ; +#85485 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#85486 = FILL_AREA_STYLE ('',( #17041 ) ) ; +#85487 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85488 = EDGE_LOOP ( 'NONE', ( #20572, #87818, #64907, #54409 ) ) ; +#85489 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85490 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 1.966666666666667007, 0.000000000000000000 ) ) ; +#85493 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85492 = PRESENTATION_STYLE_ASSIGNMENT (( #45156 ) ) ; +#85491 = SURFACE_SIDE_STYLE ('',( #23232 ) ) ; +#85494 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#85495 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80485, 'distance_accuracy_value', 'NONE'); +#85496 = CARTESIAN_POINT ( 'NONE', ( -0.1192017212701950019, -1.445336647901249938, 0.8299999999999999600 ) ) ; +#85497 = MANIFOLD_SOLID_BREP ( 'ÊäÈë61', #34008 ) ; +#85498 = VECTOR ( 'NONE', #6925, 1000.000000000000114 ) ; +#85499 = STYLED_ITEM ( 'NONE', ( #87052 ), #20261 ) ; +#85500 = SURFACE_STYLE_FILL_AREA ( #46159 ) ; +#85501 = FILL_AREA_STYLE_COLOUR ( '', #97470 ) ; +#85502 = FILL_AREA_STYLE_COLOUR ( '', #28241 ) ; +#85503 = EDGE_LOOP ( 'NONE', ( #73921, #94424, #71991, #62702, #72512, #78265 ) ) ; +#85504 = FILL_AREA_STYLE ('',( #55413 ) ) ; +#85505 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85506 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4299999999943793227, 0.000000000000000000 ) ) ; +#85508 = VECTOR ( 'NONE', #83738, 1000.000000000000000 ) ; +#85507 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96059 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12422, #66131, #19665 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85509 = CARTESIAN_POINT ( 'NONE', ( -0.07646240217796579364, -1.441250752426249893, 0.8299999999999999600 ) ) ; +#85510 = VECTOR ( 'NONE', #75971, 1000.000000000000000 ) ; +#85511 = FILL_AREA_STYLE ('',( #7321 ) ) ; +#85512 = DIRECTION ( 'NONE', ( -1.000000000000000000, -4.985173066523913740E-65, -8.980489425909800160E-49 ) ) ; +#85513 = FILL_AREA_STYLE_COLOUR ( '', #83360 ) ; +#85514 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#85515 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85516 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85517 = SURFACE_SIDE_STYLE ('',( #98754 ) ) ; +#85518 = EDGE_CURVE ( 'NONE', #72797, #16540, #22138, .T. ) ; +#85519 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85520 = DIRECTION ( 'NONE', ( -0.7071075504167436687, 0.7071060119555145906, 0.000000000000000000 ) ) ; +#85521 = SURFACE_SIDE_STYLE ('',( #31912 ) ) ; +#85522 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#85523 = SURFACE_STYLE_FILL_AREA ( #76864 ) ; +#85524 = ORIENTED_EDGE ( 'NONE', *, *, #21368, .T. ) ; +#85525 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85526 = LINE ( 'NONE', #36584, #45675 ) ; +#85527 = CARTESIAN_POINT ( 'NONE', ( -0.2747869963844669638, -1.441896757910180238, 0.8099999999995860511 ) ) ; +#85528 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70893 ) ) ; +#85530 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, 0.000000000000000000 ) ) ; +#85531 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -2.500000000000000000, 0.8299999999999999600 ) ) ; +#85532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85533 = CARTESIAN_POINT ( 'NONE', ( -1.289672647804670058, -1.082231071007949907, 0.8100000000000000533 ) ) ; +#85534 = EDGE_CURVE ( 'NONE', #100196, #13197, #61480, .T. ) ; +#85535 = ORIENTED_EDGE ( 'NONE', *, *, #99876, .F. ) ; +#85536 = CARTESIAN_POINT ( 'NONE', ( 0.03396740519372840744, -0.9529606959954437517, 0.8100000000003163558 ) ) ; +#85537 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85538 = SURFACE_SIDE_STYLE ('',( #54422 ) ) ; +#85539 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85540 = EDGE_LOOP ( 'NONE', ( #94165, #89215, #16719, #43880 ) ) ; +#85541 = FILL_AREA_STYLE_COLOUR ( '', #52662 ) ; +#85542 = STYLED_ITEM ( 'NONE', ( #93085 ), #72432 ) ; +#85543 = FILL_AREA_STYLE ('',( #92666 ) ) ; +#85544 = DIRECTION ( 'NONE', ( -0.8186165608382627301, -0.5743404272044019265, 0.000000000000000000 ) ) ; +#85545 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#85546 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57578 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84618, #69241, #15122 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85547 = ORIENTED_EDGE ( 'NONE', *, *, #50782, .T. ) ; +#85548 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94052, 'distance_accuracy_value', 'NONE'); +#85549 = DIRECTION ( 'NONE', ( 0.7071067811865504593, -0.7071067811865445751, 0.000000000000000000 ) ) ; +#85550 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85551 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#85552 = ORIENTED_EDGE ( 'NONE', *, *, #38808, .T. ) ; +#85553 = EDGE_LOOP ( 'NONE', ( #61110, #33717, #10120, #68361 ) ) ; +#85554 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70851 ), #44721 ) ; +#85555 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85556 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85557 = VERTEX_POINT ( 'NONE', #6732 ) ; +#85558 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85559 = CARTESIAN_POINT ( 'NONE', ( 0.5390356320350060404, -1.127406710959419911, 0.8299999999999999600 ) ) ; +#85560 = AXIS2_PLACEMENT_3D ( 'NONE', #66344, #51046, #97924 ) ; +#85561 = STYLED_ITEM ( 'NONE', ( #81862 ), #26829 ) ; +#85562 = PLANE ( 'NONE', #64725 ) ; +#85563 = LINE ( 'NONE', #15594, #7346 ) ; +#85564 = EDGE_CURVE ( 'NONE', #46513, #11287, #100137, .T. ) ; +#85565 = EDGE_CURVE ( 'NONE', #88085, #52805, #68537, .T. ) ; +#85566 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #9371, #68011 ) ; +#85567 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#85568 = ORIENTED_EDGE ( 'NONE', *, *, #85111, .T. ) ; +#85569 = AXIS2_PLACEMENT_3D ( 'NONE', #62676, #8430, #93248 ) ; +#85570 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49326, 'distance_accuracy_value', 'NONE'); +#85571 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85572 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#85573 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#85574 = VERTEX_POINT ( 'NONE', #15459 ) ; +#85575 = ADVANCED_FACE ( 'NONE', ( #15969 ), #22654, .T. ) ; +#85576 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 3.442791999999999852, 0.8991599999999999593 ) ) ; +#85577 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.44219999999999970, 0.8991599999999999593 ) ) ; +#85578 = EDGE_CURVE ( 'NONE', #64618, #10271, #9761, .T. ) ; +#85579 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72542 ) ) ; +#85580 = SURFACE_STYLE_FILL_AREA ( #36265 ) ; +#85581 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37325 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66674, #10968, #10440 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85582 = VERTEX_POINT ( 'NONE', #80315 ) ; +#85583 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85584 = ORIENTED_EDGE ( 'NONE', *, *, #16332, .F. ) ; +#85585 = ORIENTED_EDGE ( 'NONE', *, *, #34952, .T. ) ; +#85586 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85587 = VECTOR ( 'NONE', #52862, 1000.000000000000000 ) ; +#85589 = SURFACE_SIDE_STYLE ('',( #15093 ) ) ; +#85588 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, -3.149999999999979927, 0.000000000000000000 ) ) ; +#85590 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85591 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 8.109697000000000600, 0.8991599999999999593 ) ) ; +#85592 = ORIENTED_EDGE ( 'NONE', *, *, #39674, .T. ) ; +#85593 = STYLED_ITEM ( 'NONE', ( #50351 ), #3491 ) ; +#85594 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85595 = EDGE_CURVE ( 'NONE', #79602, #90840, #49170, .T. ) ; +#85596 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#85597 = ORIENTED_EDGE ( 'NONE', *, *, #62334, .T. ) ; +#85598 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85599 = ORIENTED_EDGE ( 'NONE', *, *, #36719, .T. ) ; +#85600 = EDGE_LOOP ( 'NONE', ( #18928, #85690, #50188, #56249 ) ) ; +#85601 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8648700000000000276 ) ) ; +#85603 = SURFACE_STYLE_USAGE ( .BOTH. , #61657 ) ; +#85602 = CARTESIAN_POINT ( 'NONE', ( 1.031909709261459973, -1.462480703074420019, 0.8100000000000000533 ) ) ; +#85604 = FILL_AREA_STYLE_COLOUR ( '', #81152 ) ; +#85605 = CARTESIAN_POINT ( 'NONE', ( 2.123820061220085265, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#85607 = ADVANCED_FACE ( 'NONE', ( #24187 ), #70611, .T. ) ; +#85606 = FACE_OUTER_BOUND ( 'NONE', #53992, .T. ) ; +#85608 = VECTOR ( 'NONE', #83938, 1000.000000000000000 ) ; +#85609 = SURFACE_STYLE_USAGE ( .BOTH. , #24371 ) ; +#85610 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#85611 = AXIS2_PLACEMENT_3D ( 'NONE', #17895, #8649, #71557 ) ; +#85612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85613 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#85614 = EDGE_CURVE ( 'NONE', #57360, #82400, #79807, .T. ) ; +#85615 = ORIENTED_EDGE ( 'NONE', *, *, #1329, .F. ) ; +#85617 = CIRCLE ( 'NONE', #93742, 0.009999999999999998473 ) ; +#85616 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85618 = EDGE_CURVE ( 'NONE', #38590, #87325, #41505, .T. ) ; +#85619 = STYLED_ITEM ( 'NONE', ( #35773 ), #72119 ) ; +#85621 = SURFACE_SIDE_STYLE ('',( #86118 ) ) ; +#85620 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85622 = LINE ( 'NONE', #40697, #98934 ) ; +#85623 = EDGE_CURVE ( 'NONE', #69473, #47396, #43873, .T. ) ; +#85625 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#85624 = AXIS2_PLACEMENT_3D ( 'NONE', #69564, #14410, #36453 ) ; +#85626 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62846 ), #92175 ) ; +#85627 = FILL_AREA_STYLE_COLOUR ( '', #79411 ) ; +#85628 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85629 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666633301, -2.299999999999999822, 3.495651678169922342E-76 ) ) ; +#85630 = SURFACE_STYLE_USAGE ( .BOTH. , #46810 ) ; +#85631 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #77620 ) ) ; +#85632 = EDGE_LOOP ( 'NONE', ( #31558, #29039, #943, #96611 ) ) ; +#85633 = STYLED_ITEM ( 'NONE', ( #85058 ), #49391 ) ; +#85634 = FILL_AREA_STYLE_COLOUR ( '', #80388 ) ; +#85635 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67813 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44866, #28573, #43891 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85637 = PRESENTATION_STYLE_ASSIGNMENT (( #22863 ) ) ; +#85636 = VECTOR ( 'NONE', #96174, 1000.000000000000000 ) ; +#85638 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#85639 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85640 = STYLED_ITEM ( 'NONE', ( #34399 ), #78321 ) ; +#85641 = SURFACE_SIDE_STYLE ('',( #15144 ) ) ; +#85642 = LINE ( 'NONE', #93758, #29275 ) ; +#85643 = SURFACE_SIDE_STYLE ('',( #55544 ) ) ; +#85644 = FILL_AREA_STYLE_COLOUR ( '', #73565 ) ; +#85645 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85646 = ADVANCED_FACE ( 'NONE', ( #39987 ), #24702, .T. ) ; +#85647 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -1.233333333333333393, 0.000000000000000000 ) ) ; +#85648 = CARTESIAN_POINT ( 'NONE', ( 10.25691912487501334, 3.831700875124988137, 0.8648700000000000276 ) ) ; +#85649 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85650 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85651 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85652 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31860 ), #54708 ) ; +#85653 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.000000000000000000 ) ) ; +#85654 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000971, -0.2399999999999999911 ) ) ; +#85655 = EDGE_CURVE ( 'NONE', #87220, #18067, #75167, .T. ) ; +#85656 = ORIENTED_EDGE ( 'NONE', *, *, #29134, .T. ) ; +#85657 = CARTESIAN_POINT ( 'NONE', ( 0.3180369866146560143, 0.2541340759269650196, 0.8100000000000000533 ) ) ; +#85658 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85659 = CARTESIAN_POINT ( 'NONE', ( 1.628132030843780331, -1.431361989143759894, 0.8299999999999977396 ) ) ; +#85661 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85660 = VECTOR ( 'NONE', #93466, 1000.000000000000114 ) ; +#85662 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72620 ), #10569 ) ; +#85663 = SURFACE_STYLE_FILL_AREA ( #93285 ) ; +#85664 = EDGE_CURVE ( 'NONE', #15107, #46104, #35868, .T. ) ; +#85665 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4699999999999999734, 0.2250000000000000333 ) ) ; +#85666 = CARTESIAN_POINT ( 'NONE', ( 1.117442990435125516, -1.129864225586409976, 0.8099999999999081268 ) ) ; +#85667 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#85668 = VERTEX_POINT ( 'NONE', #97586 ) ; +#85669 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#85670 = ADVANCED_FACE ( 'NONE', ( #11261 ), #89958, .T. ) ; +#85671 = AXIS2_PLACEMENT_3D ( 'NONE', #48694, #88487, #2227 ) ; +#85672 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.23504400000000025, 0.8648700000000000276 ) ) ; +#85673 = SURFACE_STYLE_FILL_AREA ( #38709 ) ; +#85674 = AXIS2_PLACEMENT_3D ( 'NONE', #32589, #39730, #70879 ) ; +#85675 = SURFACE_SIDE_STYLE ('',( #84667 ) ) ; +#85676 = ORIENTED_EDGE ( 'NONE', *, *, #100187, .F. ) ; +#85677 = ORIENTED_EDGE ( 'NONE', *, *, #59214, .F. ) ; +#85678 = AXIS2_PLACEMENT_3D ( 'NONE', #67473, #98547, #21036 ) ; +#85679 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.500000000000000222, 0.8100000000000000533 ) ) ; +#85680 = VERTEX_POINT ( 'NONE', #20012 ) ; +#85681 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85682 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85683 = SURFACE_STYLE_FILL_AREA ( #54580 ) ; +#85684 = EDGE_CURVE ( 'NONE', #9637, #97953, #12276, .T. ) ; +#85685 = LINE ( 'NONE', #416, #49595 ) ; +#85686 = PRODUCT_CONTEXT ( 'NONE', #65775, 'mechanical' ) ; +#85687 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#85688 = VECTOR ( 'NONE', #80740, 1000.000000000000000 ) ; +#85690 = ORIENTED_EDGE ( 'NONE', *, *, #60800, .F. ) ; +#85689 = ORIENTED_EDGE ( 'NONE', *, *, #77052, .T. ) ; +#85691 = ORIENTED_EDGE ( 'NONE', *, *, #50254, .T. ) ; +#85692 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98244, 'distance_accuracy_value', 'NONE'); +#85693 = STYLED_ITEM ( 'NONE', ( #80500 ), #54344 ) ; +#85694 = FILL_AREA_STYLE ('',( #79063 ) ) ; +#85695 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#85696 = EDGE_LOOP ( 'NONE', ( #58740, #37028, #4272, #87126 ) ) ; +#85697 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85698 = ADVANCED_FACE ( 'NONE', ( #59374 ), #51380, .T. ) ; +#85699 = VECTOR ( 'NONE', #12746, 1000.000000000000000 ) ; +#85700 = FILL_AREA_STYLE ('',( #96240 ) ) ; +#85701 = ORIENTED_EDGE ( 'NONE', *, *, #63137, .T. ) ; +#85702 = AXIS2_PLACEMENT_3D ( 'NONE', #34990, #41628, #4802 ) ; +#85703 = ORIENTED_EDGE ( 'NONE', *, *, #51746, .F. ) ; +#85704 = ORIENTED_EDGE ( 'NONE', *, *, #49643, .T. ) ; +#85705 = SURFACE_STYLE_USAGE ( .BOTH. , #86211 ) ; +#85706 = SURFACE_SIDE_STYLE ('',( #61760 ) ) ; +#85707 = PRESENTATION_STYLE_ASSIGNMENT (( #45369 ) ) ; +#85708 = ORIENTED_EDGE ( 'NONE', *, *, #21099, .F. ) ; +#85709 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85710 = VECTOR ( 'NONE', #86294, 1000.000000000000000 ) ; +#85711 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8199999999999999512 ) ) ; +#85712 = SURFACE_STYLE_FILL_AREA ( #86221 ) ; +#85713 = ORIENTED_EDGE ( 'NONE', *, *, #32743, .T. ) ; +#85716 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85715 = VECTOR ( 'NONE', #10229, 1000.000000000000000 ) ; +#85714 = CARTESIAN_POINT ( 'NONE', ( 1.511688311688310193, -1.091883116883120008, 0.8199999999999999512 ) ) ; +#85717 = FACE_OUTER_BOUND ( 'NONE', #96947, .T. ) ; +#85718 = ORIENTED_EDGE ( 'NONE', *, *, #20236, .F. ) ; +#85719 = ORIENTED_EDGE ( 'NONE', *, *, #85222, .F. ) ; +#85721 = FILL_AREA_STYLE_COLOUR ( '', #40551 ) ; +#85720 = FILL_AREA_STYLE ('',( #67497 ) ) ; +#85722 = CARTESIAN_POINT ( 'NONE', ( 1.813028831487849990, -1.379727385542079965, 0.8300000000000002931 ) ) ; +#85723 = STYLED_ITEM ( 'NONE', ( #44762 ), #39232 ) ; +#85724 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#85725 = VECTOR ( 'NONE', #65704, 1000.000000000000000 ) ; +#85726 = CARTESIAN_POINT ( 'NONE', ( -0.4883433428992630665, -1.252526457973309970, 0.8100000000000000533 ) ) ; +#85727 = SURFACE_SIDE_STYLE ('',( #62784 ) ) ; +#85728 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#85729 = SURFACE_STYLE_FILL_AREA ( #54629 ) ; +#85730 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28745, 'distance_accuracy_value', 'NONE'); +#85731 = SURFACE_SIDE_STYLE ('',( #14228 ) ) ; +#85732 = EDGE_LOOP ( 'NONE', ( #6989, #17505, #1101, #15106 ) ) ; +#85733 = ORIENTED_EDGE ( 'NONE', *, *, #27649, .T. ) ; +#85734 = EDGE_CURVE ( 'NONE', #42765, #58119, #92445, .T. ) ; +#85735 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51539 ), #87421 ) ; +#85736 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85737 = FACE_OUTER_BOUND ( 'NONE', #11184, .T. ) ; +#85739 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85738 = LINE ( 'NONE', #7545, #98474 ) ; +#85740 = SURFACE_STYLE_FILL_AREA ( #54112 ) ; +#85741 = LINE ( 'NONE', #33674, #99979 ) ; +#85742 = FILL_AREA_STYLE_COLOUR ( '', #41526 ) ; +#85743 = SURFACE_STYLE_USAGE ( .BOTH. , #76580 ) ; +#85744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85745 = PRESENTATION_STYLE_ASSIGNMENT (( #84258 ) ) ; +#85746 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85747 = FACE_OUTER_BOUND ( 'NONE', #88483, .T. ) ; +#85748 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85749 = STYLED_ITEM ( 'NONE', ( #10048 ), #29988 ) ; +#85751 = CARTESIAN_POINT ( 'NONE', ( 8.687143000000000725, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#85750 = PLANE ( 'NONE', #57174 ) ; +#85752 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#85753 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#85754 = LINE ( 'NONE', #94908, #97348 ) ; +#85755 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#85756 = AXIS2_PLACEMENT_3D ( 'NONE', #45941, #91444, #53155 ) ; +#85757 = CIRCLE ( 'NONE', #53204, 0.2000000000000000944 ) ; +#85758 = ORIENTED_EDGE ( 'NONE', *, *, #85371, .F. ) ; +#85759 = SURFACE_STYLE_FILL_AREA ( #86273 ) ; +#85760 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85762 = ADVANCED_FACE ( 'NONE', ( #7615 ), #38859, .T. ) ; +#85761 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #45003 ), #100305 ) ; +#85764 = MANIFOLD_SOLID_BREP ( 'ÊäÈë112', #69662 ) ; +#85763 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70690, 'distance_accuracy_value', 'NONE'); +#85765 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26523, 'distance_accuracy_value', 'NONE'); +#85766 = AXIS2_PLACEMENT_3D ( 'NONE', #69522, #70546, #15393 ) ; +#85767 = PRESENTATION_STYLE_ASSIGNMENT (( #14423 ) ) ; +#85768 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#85770 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 4.496381000000000405, 0.8648700000000000276 ) ) ; +#85769 = VECTOR ( 'NONE', #92235, 1000.000000000000000 ) ; +#85771 = PLANE ( 'NONE', #11340 ) ; +#85772 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52285 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71505, #25074, #17357 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85773 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100951 ) ; +#85774 = VERTEX_POINT ( 'NONE', #32723 ) ; +#85775 = FILL_AREA_STYLE_COLOUR ( '', #95468 ) ; +#85776 = VERTEX_POINT ( 'NONE', #1057 ) ; +#85777 = AXIS2_PLACEMENT_3D ( 'NONE', #66913, #66422, #83261 ) ; +#85778 = EDGE_CURVE ( 'NONE', #71271, #39620, #60364, .T. ) ; +#85779 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86435, 'distance_accuracy_value', 'NONE'); +#85780 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23757, 'distance_accuracy_value', 'NONE'); +#85781 = SURFACE_STYLE_FILL_AREA ( #93412 ) ; +#85782 = PRESENTATION_STYLE_ASSIGNMENT (( #31168 ) ) ; +#85783 = SURFACE_SIDE_STYLE ('',( #55690 ) ) ; +#85784 = LINE ( 'NONE', #94934, #88522 ) ; +#85785 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85786 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76791, #61000, #77804, #83959 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85787 = PLANE ( 'NONE', #46555 ) ; +#85788 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#85789 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85790 = CARTESIAN_POINT ( 'NONE', ( -0.7884757841786803612, 1.392126994685491947, 0.8100000000000000533 ) ) ; +#85791 = ADVANCED_FACE ( 'NONE', ( #15845 ), #16849, .T. ) ; +#85792 = ORIENTED_EDGE ( 'NONE', *, *, #3306, .T. ) ; +#85793 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#85794 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#85796 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#85795 = SURFACE_SIDE_STYLE ('',( #15 ) ) ; +#85797 = VERTEX_POINT ( 'NONE', #94962 ) ; +#85798 = SURFACE_SIDE_STYLE ('',( #32703 ) ) ; +#85799 = AXIS2_PLACEMENT_3D ( 'NONE', #60576, #90691, #98766 ) ; +#85800 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85801 = ORIENTED_EDGE ( 'NONE', *, *, #73552, .F. ) ; +#85802 = SURFACE_STYLE_USAGE ( .BOTH. , #9629 ) ; +#85803 = FACE_OUTER_BOUND ( 'NONE', #36114, .T. ) ; +#85804 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85805 = ADVANCED_FACE ( 'NONE', ( #95464 ), #93934, .T. ) ; +#85806 = EDGE_CURVE ( 'NONE', #65265, #25280, #37733, .T. ) ; +#85807 = DIRECTION ( 'NONE', ( 0.000000000000000000, 3.355477456267752477E-13, -1.000000000000000000 ) ) ; +#85808 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2669 ), #14042 ) ; +#85809 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85810 = LINE ( 'NONE', #15840, #32841 ) ; +#85811 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#85812 = CARTESIAN_POINT ( 'NONE', ( -0.05209297649735774444, 1.199843002877106324, 0.8100000000000002753 ) ) ; +#85814 = ORIENTED_EDGE ( 'NONE', *, *, #14004, .T. ) ; +#85813 = VERTEX_POINT ( 'NONE', #87328 ) ; +#85815 = VECTOR ( 'NONE', #82486, 1000.000000000000000 ) ; +#85816 = ADVANCED_FACE ( 'NONE', ( #23888 ), #76976, .T. ) ; +#85817 = EDGE_CURVE ( 'NONE', #74243, #100385, #99840, .T. ) ; +#85818 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85819 = ORIENTED_EDGE ( 'NONE', *, *, #93494, .T. ) ; +#85820 = STYLED_ITEM ( 'NONE', ( #75290 ), #13159 ) ; +#85821 = FILL_AREA_STYLE ('',( #9643 ) ) ; +#85822 = SURFACE_STYLE_USAGE ( .BOTH. , #7116 ) ; +#85823 = ORIENTED_EDGE ( 'NONE', *, *, #68326, .T. ) ; +#85824 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #22045, #61882, #45489, #82839 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85825 = ORIENTED_EDGE ( 'NONE', *, *, #21134, .F. ) ; +#85826 = FILL_AREA_STYLE_COLOUR ( '', #98597 ) ; +#85827 = EDGE_CURVE ( 'NONE', #5312, #6840, #92761, .T. ) ; +#85828 = FACE_OUTER_BOUND ( 'NONE', #82830, .T. ) ; +#85829 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -13.25000000000000000 ) ) ; +#85830 = PLANE ( 'NONE', #82366 ) ; +#85831 = ORIENTED_EDGE ( 'NONE', *, *, #8707, .T. ) ; +#85832 = ORIENTED_EDGE ( 'NONE', *, *, #25123, .F. ) ; +#85833 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#85834 = ORIENTED_EDGE ( 'NONE', *, *, #69620, .T. ) ; +#85835 = EDGE_CURVE ( 'NONE', #72252, #74032, #14142, .T. ) ; +#85836 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#85837 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33682 ), #30337 ) ; +#85839 = ORIENTED_EDGE ( 'NONE', *, *, #63405, .T. ) ; +#85838 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#85840 = MANIFOLD_SOLID_BREP ( 'ÊäÈë47', #45165 ) ; +#85841 = VECTOR ( 'NONE', #24250, 1000.000000000000000 ) ; +#85842 = FILL_AREA_STYLE ('',( #78200 ) ) ; +#85843 = ORIENTED_EDGE ( 'NONE', *, *, #81851, .F. ) ; +#85844 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85845 = FILL_AREA_STYLE_COLOUR ( '', #96616 ) ; +#85846 = ORIENTED_EDGE ( 'NONE', *, *, #50136, .F. ) ; +#85847 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61464 ), #33764 ) ; +#85848 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28781 ), #7485 ) ; +#85849 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 11.02344800000000014, 0.8991599999999999593 ) ) ; +#85850 = STYLED_ITEM ( 'NONE', ( #26240 ), #78907 ) ; +#85851 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 8.109697000000000600, 0.8648700000000000276 ) ) ; +#85852 = STYLED_ITEM ( 'NONE', ( #927 ), #49094 ) ; +#85854 = VERTEX_POINT ( 'NONE', #77990 ) ; +#85853 = SURFACE_SIDE_STYLE ('',( #63418 ) ) ; +#85855 = CARTESIAN_POINT ( 'NONE', ( 1.320874515982729980, -0.9101533448649530289, 0.8299999999999998490 ) ) ; +#85856 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85858 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#85857 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37207 ) ) ; +#85859 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#85860 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85861 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#85862 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16921, #8690, #63928, #62424 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#85863 = CARTESIAN_POINT ( 'NONE', ( 1.779394466811810016, -1.241062917987890257, 0.8099999999999996092 ) ) ; +#85864 = ORIENTED_EDGE ( 'NONE', *, *, #81062, .F. ) ; +#85865 = EDGE_CURVE ( 'NONE', #70688, #31070, #85642, .T. ) ; +#85866 = SURFACE_STYLE_USAGE ( .BOTH. , #39916 ) ; +#85867 = PLANE ( 'NONE', #71179 ) ; +#85868 = VECTOR ( 'NONE', #45798, 1000.000000000000114 ) ; +#85869 = STYLED_ITEM ( 'NONE', ( #83434 ), #16139 ) ; +#85870 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#85871 = ADVANCED_FACE ( 'NONE', ( #86136, #75974 ), #61268, .T. ) ; +#85873 = FILL_AREA_STYLE_COLOUR ( '', #21457 ) ; +#85872 = FILL_AREA_STYLE ('',( #1634 ) ) ; +#85874 = FACE_OUTER_BOUND ( 'NONE', #90665, .T. ) ; +#85875 = CARTESIAN_POINT ( 'NONE', ( -1.416666666666666519, -3.099999999999989875, 0.000000000000000000 ) ) ; +#85876 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85877 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36198 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98153, #28772, #91562 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85878 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#85879 = VERTEX_POINT ( 'NONE', #15219 ) ; +#85880 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29060 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73885, #66219, #98778 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#85881 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85882 = EDGE_LOOP ( 'NONE', ( #100461, #69878, #38595, #43746 ) ) ; +#85883 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85884 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#85885 = FILL_AREA_STYLE ('',( #55282 ) ) ; +#85886 = CIRCLE ( 'NONE', #33806, 0.3000000000000000444 ) ; +#85887 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#85888 = ORIENTED_EDGE ( 'NONE', *, *, #28185, .F. ) ; +#85889 = LINE ( 'NONE', #39937, #32676 ) ; +#85890 = ADVANCED_FACE ( 'NONE', ( #54606 ), #53085, .F. ) ; +#85891 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85892 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#85893 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, -0.02000000000000000042 ) ) ; +#85894 = PLANE ( 'NONE', #3561 ) ; +#85895 = SURFACE_STYLE_FILL_AREA ( #54797 ) ; +#85896 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.4245906043549200204, -6.018531076210109988E-33 ) ) ; +#85897 = CARTESIAN_POINT ( 'NONE', ( 0.02974286737007770035, -0.9500768360162820114, 0.8100000000000000533 ) ) ; +#85898 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#85899 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91117, 'distance_accuracy_value', 'NONE'); +#85900 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#85901 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#85902 = ORIENTED_EDGE ( 'NONE', *, *, #58986, .F. ) ; +#85903 = VERTEX_POINT ( 'NONE', #77550 ) ; +#85904 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#85905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21252, 'distance_accuracy_value', 'NONE'); +#85906 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38871, 'distance_accuracy_value', 'NONE'); +#85907 = SURFACE_SIDE_STYLE ('',( #32809 ) ) ; +#85908 = LINE ( 'NONE', #31279, #21791 ) ; +#85909 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#85910 = SURFACE_STYLE_FILL_AREA ( #71104 ) ; +#85911 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#85912 = VECTOR ( 'NONE', #80647, 1000.000000000000000 ) ; +#85913 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.699999999999999956, -0.02000000000000000042 ) ) ; +#85914 = CARTESIAN_POINT ( 'NONE', ( 0.07012987012986959812, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#85915 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85916 = ORIENTED_EDGE ( 'NONE', *, *, #6357, .F. ) ; +#85918 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85917 = AXIS2_PLACEMENT_3D ( 'NONE', #100707, #31396, #76855 ) ; +#85919 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85920 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45506, 'distance_accuracy_value', 'NONE'); +#85921 = ORIENTED_EDGE ( 'NONE', *, *, #71743, .F. ) ; +#85922 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, 0.2999999999999991562, 0.000000000000000000 ) ) ; +#85923 = FILL_AREA_STYLE ('',( #53287 ) ) ; +#85924 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28850 ), #67967 ) ; +#85925 = ORIENTED_EDGE ( 'NONE', *, *, #51614, .F. ) ; +#85926 = SURFACE_SIDE_STYLE ('',( #55332 ) ) ; +#85927 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85928 = PLANE ( 'NONE', #18434 ) ; +#85929 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#85931 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85930 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29102 ), #37049 ) ; +#85932 = VERTEX_POINT ( 'NONE', #46895 ) ; +#85933 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85934 = ADVANCED_FACE ( 'NONE', ( #15743 ), #69351, .F. ) ; +#85936 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66413 ) ) ; +#85935 = SURFACE_SIDE_STYLE ('',( #84923 ) ) ; +#85937 = STYLED_ITEM ( 'NONE', ( #80818 ), #16307 ) ; +#85938 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0402_20210301.STEP', ( #46738, #35434 ), #98856 ) ; +#85939 = CARTESIAN_POINT ( 'NONE', ( 0.3661974308942260170, -0.9626035508172909871, 0.8300000000000002931 ) ) ; +#85940 = CLOSED_SHELL ( 'NONE', ( #18202, #30967, #75046, #42379, #62234, #59979 ) ) ; +#85941 = MANIFOLD_SOLID_BREP ( 'ÊäÈë108', #22377 ) ; +#85942 = ORIENTED_EDGE ( 'NONE', *, *, #7819, .T. ) ; +#85943 = AXIS2_PLACEMENT_3D ( 'NONE', #91642, #69128, #7810 ) ; +#85944 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28877 ) ) ; +#85946 = EDGE_CURVE ( 'NONE', #17079, #63256, #25473, .T. ) ; +#85945 = LINE ( 'NONE', #69066, #62035 ) ; +#85947 = PLANE ( 'NONE', #382 ) ; +#85948 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85949 = VERTEX_POINT ( 'NONE', #56632 ) ; +#85950 = ORIENTED_EDGE ( 'NONE', *, *, #54981, .T. ) ; +#85951 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85952 = VECTOR ( 'NONE', #42871, 1000.000000000000000 ) ; +#85953 = VERTEX_POINT ( 'NONE', #1975 ) ; +#85954 = EDGE_CURVE ( 'NONE', #16995, #22670, #1477, .T. ) ; +#85955 = ORIENTED_EDGE ( 'NONE', *, *, #97584, .F. ) ; +#85956 = EDGE_LOOP ( 'NONE', ( #38858, #93394, #49324, #97395 ) ) ; +#85957 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85959 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85958 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4849999999999999867, 0.2500000000000000000 ) ) ; +#85960 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#85961 = FACE_OUTER_BOUND ( 'NONE', #51949, .T. ) ; +#85962 = ORIENTED_EDGE ( 'NONE', *, *, #7389, .F. ) ; +#85963 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85964 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#85965 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85966 = VERTEX_POINT ( 'NONE', #42297 ) ; +#85967 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#85968 = FILL_AREA_STYLE_COLOUR ( '', #78996 ) ; +#85969 = SURFACE_STYLE_USAGE ( .BOTH. , #31338 ) ; +#85970 = SURFACE_STYLE_USAGE ( .BOTH. , #29341 ) ; +#85971 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24049 ), #30472 ) ; +#85972 = ORIENTED_EDGE ( 'NONE', *, *, #78103, .T. ) ; +#85973 = STYLED_ITEM ( 'NONE', ( #77843 ), #74375 ) ; +#85975 = FILL_AREA_STYLE ('',( #54861 ) ) ; +#85974 = FILL_AREA_STYLE ('',( #40029 ) ) ; +#85976 = EDGE_LOOP ( 'NONE', ( #54738, #12570, #66153, #44652, #60108, #12290 ) ) ; +#85977 = EDGE_CURVE ( 'NONE', #44500, #42023, #50523, .T. ) ; +#85978 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#85979 = SURFACE_SIDE_STYLE ('',( #24231 ) ) ; +#85980 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#85981 = LINE ( 'NONE', #48210, #35392 ) ; +#85982 = VECTOR ( 'NONE', #16802, 1000.000000000000000 ) ; +#85983 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71261 ), #59938 ) ; +#85984 = VERTEX_POINT ( 'NONE', #72926 ) ; +#85985 = PLANE ( 'NONE', #31990 ) ; +#85986 = ORIENTED_EDGE ( 'NONE', *, *, #12914, .F. ) ; +#85987 = PLANE ( 'NONE', #6222 ) ; +#85988 = EDGE_CURVE ( 'NONE', #50477, #2083, #95869, .T. ) ; +#85989 = SURFACE_SIDE_STYLE ('',( #47691 ) ) ; +#85990 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4282, 'distance_accuracy_value', 'NONE'); +#85991 = FILL_AREA_STYLE ('',( #54879 ) ) ; +#85992 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999734, 0.000000000000000000 ) ) ; +#85993 = LINE ( 'NONE', #24245, #94834 ) ; +#85994 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#85995 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999969891, 0.000000000000000000 ) ) ; +#85996 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#85997 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59955 ), #10925 ) ; +#85998 = EDGE_LOOP ( 'NONE', ( #73751, #28831, #3313, #74682 ) ) ; +#85999 = SURFACE_STYLE_USAGE ( .BOTH. , #23231 ) ; +#86000 = VECTOR ( 'NONE', #18054, 1000.000000000000000 ) ; +#86001 = STYLED_ITEM ( 'NONE', ( #28148 ), #62512 ) ; +#86002 = CARTESIAN_POINT ( 'NONE', ( -0.1561074608318659962, -1.440618065759700084, 0.8100000000000000533 ) ) ; +#86003 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61620 ), #98958 ) ; +#86004 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72978 ), #20781 ) ; +#86005 = FILL_AREA_STYLE ('',( #54900 ) ) ; +#86006 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86007 = CLOSED_SHELL ( 'NONE', ( #56962, #69588, #28070, #19635, #29989, #38207 ) ) ; +#86008 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86009 = ORIENTED_EDGE ( 'NONE', *, *, #77385, .T. ) ; +#86010 = EDGE_CURVE ( 'NONE', #94036, #85184, #10032, .T. ) ; +#86011 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86012 = VECTOR ( 'NONE', #25381, 1000.000000000000000 ) ; +#86013 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86014 = FILL_AREA_STYLE ('',( #79380 ) ) ; +#86015 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86016 = LINE ( 'NONE', #38556, #100523 ) ; +#86017 = STYLED_ITEM ( 'NONE', ( #64913 ), #50372 ) ; +#86018 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86019 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86020 = EDGE_CURVE ( 'NONE', #59324, #69765, #79586, .T. ) ; +#86021 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86022 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86023 = SURFACE_SIDE_STYLE ('',( #45676 ) ) ; +#86024 = FILL_AREA_STYLE ('',( #54916 ) ) ; +#86025 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#86026 = PRESENTATION_STYLE_ASSIGNMENT (( #78874 ) ) ; +#86027 = STYLED_ITEM ( 'NONE', ( #95422 ), #49831 ) ; +#86028 = SURFACE_STYLE_FILL_AREA ( #23257 ) ; +#86029 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #47469 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #13035 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#86030 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#86031 = ORIENTED_EDGE ( 'NONE', *, *, #88147, .F. ) ; +#86032 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4685, 'distance_accuracy_value', 'NONE'); +#86033 = SURFACE_SIDE_STYLE ('',( #78883 ) ) ; +#86034 = LINE ( 'NONE', #55438, #92762 ) ; +#86035 = LINE ( 'NONE', #100723, #47838 ) ; +#86036 = LINE ( 'NONE', #31925, #3579 ) ; +#86037 = PRESENTATION_STYLE_ASSIGNMENT (( #50910 ) ) ; +#86038 = CARTESIAN_POINT ( 'NONE', ( -1.277337950986729975, -1.102553831183370026, 0.8100000000000000533 ) ) ; +#86039 = ADVANCED_FACE ( 'NONE', ( #57128 ), #11044, .T. ) ; +#86040 = ORIENTED_EDGE ( 'NONE', *, *, #78973, .T. ) ; +#86041 = CARTESIAN_POINT ( 'NONE', ( 0.06488746468188884287, -1.012324799888078442, 0.8100000000002275380 ) ) ; +#86042 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35266, 'distance_accuracy_value', 'NONE'); +#86043 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#86044 = AXIS2_PLACEMENT_3D ( 'NONE', #87830, #42391, #41390 ) ; +#86045 = SURFACE_STYLE_USAGE ( .BOTH. , #46199 ) ; +#86046 = STYLED_ITEM ( 'NONE', ( #39362 ), #74595 ) ; +#86047 = ORIENTED_EDGE ( 'NONE', *, *, #75580, .T. ) ; +#86048 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86049 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.499999999999960032, 0.1829999999999999960 ) ) ; +#86050 = FACE_OUTER_BOUND ( 'NONE', #54317, .T. ) ; +#86051 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.033333333333333659, 0.000000000000000000 ) ) ; +#86052 = ORIENTED_EDGE ( 'NONE', *, *, #1833, .T. ) ; +#86053 = ADVANCED_FACE ( 'NONE', ( #67744 ), #13061, .T. ) ; +#86054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42995, 'distance_accuracy_value', 'NONE'); +#86055 = VECTOR ( 'NONE', #82174, 1000.000000000000114 ) ; +#86056 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42241 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60559, #92154, #76334 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86057 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59943 ), #89354 ) ; +#86058 = ORIENTED_EDGE ( 'NONE', *, *, #4619, .T. ) ; +#86059 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86060 = SURFACE_STYLE_USAGE ( .BOTH. , #62617 ) ; +#86061 = VERTEX_POINT ( 'NONE', #44755 ) ; +#86062 = FILL_AREA_STYLE_COLOUR ( '', #6935 ) ; +#86063 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8100000000000000533 ) ) ; +#86064 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#86065 = PRESENTATION_STYLE_ASSIGNMENT (( #41142 ) ) ; +#86066 = VECTOR ( 'NONE', #60516, 1000.000000000000000 ) ; +#86067 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #37878, #11610 ) ; +#86068 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#86069 = VECTOR ( 'NONE', #91922, 1000.000000000000114 ) ; +#86070 = VERTEX_POINT ( 'NONE', #66752 ) ; +#86071 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86072 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38831 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18460, #74118, #73116 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86073 = STYLED_ITEM ( 'NONE', ( #72496 ), #16455 ) ; +#86074 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86075 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73055 ) ) ; +#86076 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86077 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86078 = CLOSED_SHELL ( 'NONE', ( #71765, #84531, #2823, #58071, #76816, #59461, #67148, #13478, #5404, #98842, #53808, #82095, #52814, #95382, #49211, #22833, #74952, #96217, #25674, #36412, #83147, #81307, #75006, #69496, #93450, #74872, #13468, #40472, #43801, #75854, #2147, #65518, #22542, #2671, #56971, #87789, #61176, #61304, #64612, #97801, #94677, #77505, #21482, #72454, #51363, #37586, #4325, #51512, #44441, #84400, #90071, #64250, #29806, #72584, #46859, #59543, #86857, #39250, #32543, #64545, #80213, #13490, #40608, #73933, #75022, #66869, #36487, #1196, #50927 ) ) ; +#86079 = ORIENTED_EDGE ( 'NONE', *, *, #743, .T. ) ; +#86080 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86081 = AXIS2_PLACEMENT_3D ( 'NONE', #88323, #57720, #72004 ) ; +#86082 = SURFACE_SIDE_STYLE ('',( #70763 ) ) ; +#86083 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#86085 = ORIENTED_EDGE ( 'NONE', *, *, #83816, .F. ) ; +#86084 = EDGE_CURVE ( 'NONE', #41604, #94730, #22790, .T. ) ; +#86086 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79640 ) ) ; +#86087 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86088 = EDGE_LOOP ( 'NONE', ( #94357, #100351, #81720, #80596 ) ) ; +#86089 = EDGE_LOOP ( 'NONE', ( #83338, #39711, #42611, #96857, #77297 ) ) ; +#86090 = CARTESIAN_POINT ( 'NONE', ( 1.347523492357600050, -1.285676881280640282, 0.8100000000000000533 ) ) ; +#86091 = EDGE_CURVE ( 'NONE', #6047, #13813, #60150, .T. ) ; +#86093 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#86092 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.000000000000000000 ) ) ; +#86094 = VERTEX_POINT ( 'NONE', #91245 ) ; +#86095 = CIRCLE ( 'NONE', #11021, 0.009999999999999998473 ) ; +#86096 = FILL_AREA_STYLE_COLOUR ( '', #87465 ) ; +#86097 = CARTESIAN_POINT ( 'NONE', ( 10.38419900000000062, 8.569316000000000599, 0.8991599999999999593 ) ) ; +#86098 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000000, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#86099 = PRESENTATION_STYLE_ASSIGNMENT (( #71289 ) ) ; +#86100 = ORIENTED_EDGE ( 'NONE', *, *, #27158, .F. ) ; +#86102 = PLANE ( 'NONE', #12710 ) ; +#86101 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86103 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#86104 = ORIENTED_EDGE ( 'NONE', *, *, #38406, .F. ) ; +#86105 = VERTEX_POINT ( 'NONE', #28471 ) ; +#86106 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86107 = EDGE_CURVE ( 'NONE', #60384, #55806, #46179, .T. ) ; +#86108 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86109 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #13944, .NOT_KNOWN. ) ; +#86110 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36094 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19916, #75542, #36752 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86111 = SURFACE_SIDE_STYLE ('',( #63172 ) ) ; +#86112 = PRESENTATION_STYLE_ASSIGNMENT (( #46796 ) ) ; +#86113 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86114 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86115 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71472 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25028, #9586, #47975 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86116 = ORIENTED_EDGE ( 'NONE', *, *, #1005, .F. ) ; +#86118 = SURFACE_STYLE_FILL_AREA ( #51635 ) ; +#86117 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 4.807508000000000337, 0.8648700000000000276 ) ) ; +#86119 = SURFACE_SIDE_STYLE ('',( #53492 ) ) ; +#86120 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.05000000000000000278, 0.08229670385730990245 ) ) ; +#86121 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.35000000000000142 ) ) ; +#86122 = VECTOR ( 'NONE', #17587, 1000.000000000000000 ) ; +#86123 = FILL_AREA_STYLE_COLOUR ( '', #48728 ) ; +#86124 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.300000000000000266, 8.972889346935576195E-79 ) ) ; +#86125 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86126 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#86127 = ORIENTED_EDGE ( 'NONE', *, *, #78463, .T. ) ; +#86128 = LINE ( 'NONE', #56545, #26053 ) ; +#86129 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86130 = FILL_AREA_STYLE ('',( #23881 ) ) ; +#86131 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000005745, 0.3800000000146489532, 0.6999285677985319643 ) ) ; +#86132 = LINE ( 'NONE', #70312, #95252 ) ; +#86133 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10906, 'distance_accuracy_value', 'NONE'); +#86134 = ADVANCED_FACE ( 'NONE', ( #97373 ), #66272, .T. ) ; +#86135 = ADVANCED_FACE ( 'NONE', ( #38143 ), #77937, .F. ) ; +#86136 = FACE_BOUND ( 'NONE', #35348, .T. ) ; +#86137 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#86138 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86140 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4867 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12729, #92888, #7075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86139 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, -0.1350000000000000089 ) ) ; +#86141 = AXIS2_PLACEMENT_3D ( 'NONE', #27923, #99257, #35585 ) ; +#86142 = VECTOR ( 'NONE', #6787, 1000.000000000000114 ) ; +#86143 = PRESENTATION_STYLE_ASSIGNMENT (( #1407 ) ) ; +#86144 = CARTESIAN_POINT ( 'NONE', ( 1.806468873558769728, -1.190451802854979757, 0.8100000000000004974 ) ) ; +#86145 = LINE ( 'NONE', #93273, #35699 ) ; +#86146 = VECTOR ( 'NONE', #28799, 1000.000000000000000 ) ; +#86147 = AXIS2_PLACEMENT_3D ( 'NONE', #93971, #30703, #14855 ) ; +#86148 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86149 = PLANE ( 'NONE', #68233 ) ; +#86150 = EDGE_CURVE ( 'NONE', #99161, #16321, #77423, .T. ) ; +#86151 = ORIENTED_EDGE ( 'NONE', *, *, #31524, .T. ) ; +#86152 = CARTESIAN_POINT ( 'NONE', ( -0.8103896103896099934, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#86153 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23469, 'distance_accuracy_value', 'NONE'); +#86155 = CARTESIAN_POINT ( 'NONE', ( 0.5799999999751886959, 0.2999999999999999334, 5.437616897915546617E-17 ) ) ; +#86154 = CARTESIAN_POINT ( 'NONE', ( 0.001293116504768550062, -1.273483528256009967, 0.8300000000000002931 ) ) ; +#86156 = ADVANCED_FACE ( 'NONE', ( #7399 ), #68739, .F. ) ; +#86157 = PLANE ( 'NONE', #72611 ) ; +#86158 = PRESENTATION_STYLE_ASSIGNMENT (( #31040 ) ) ; +#86159 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61778 ) ) ; +#86160 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.2999999999999989897, 0.1829999999999749882 ) ) ; +#86161 = AXIS2_PLACEMENT_3D ( 'NONE', #68130, #74818, #4849 ) ; +#86162 = ORIENTED_EDGE ( 'NONE', *, *, #69546, .T. ) ; +#86163 = FILL_AREA_STYLE_COLOUR ( '', #95991 ) ; +#86164 = SURFACE_STYLE_USAGE ( .BOTH. , #55063 ) ; +#86165 = STYLED_ITEM ( 'NONE', ( #46452 ), #43989 ) ; +#86166 = CARTESIAN_POINT ( 'NONE', ( -0.4500000000000000666, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#86167 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.000000000000000000, 0.2400000000000000189 ) ) ; +#86168 = ADVANCED_FACE ( 'NONE', ( #92231 ), #22298, .T. ) ; +#86169 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63604, 'distance_accuracy_value', 'NONE'); +#86170 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#86171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23262, 'distance_accuracy_value', 'NONE'); +#86172 = ORIENTED_EDGE ( 'NONE', *, *, #6963, .F. ) ; +#86173 = EDGE_CURVE ( 'NONE', #59792, #11704, #79979, .T. ) ; +#86174 = ORIENTED_EDGE ( 'NONE', *, *, #81248, .F. ) ; +#86175 = LINE ( 'NONE', #84255, #5601 ) ; +#86176 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86177 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#86178 = VERTEX_POINT ( 'NONE', #41170 ) ; +#86179 = LINE ( 'NONE', #86696, #21674 ) ; +#86180 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1441 ), #92704 ) ; +#86181 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000004913, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#86182 = FILL_AREA_STYLE_COLOUR ( '', #727 ) ; +#86183 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12858, 'distance_accuracy_value', 'NONE'); +#86184 = SURFACE_SIDE_STYLE ('',( #23941 ) ) ; +#86185 = ADVANCED_FACE ( 'NONE', ( #831 ), #71282, .T. ) ; +#86186 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38902 ) ) ; +#86187 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #97037 ) ; +#86188 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#86189 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.449999999999999956, -0.02000000000000000042 ) ) ; +#86190 = ADVANCED_FACE ( 'NONE', ( #1858 ), #88614, .T. ) ; +#86192 = ORIENTED_EDGE ( 'NONE', *, *, #3041, .T. ) ; +#86191 = ORIENTED_EDGE ( 'NONE', *, *, #60736, .T. ) ; +#86193 = EDGE_LOOP ( 'NONE', ( #92671, #18098, #18875, #64339 ) ) ; +#86194 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86195 = AXIS2_PLACEMENT_3D ( 'NONE', #68574, #46071, #60468 ) ; +#86196 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #60155 ) ) ; +#86197 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86198 = ORIENTED_EDGE ( 'NONE', *, *, #3159, .F. ) ; +#86199 = AXIS2_PLACEMENT_3D ( 'NONE', #54449, #85558, #16096 ) ; +#86200 = CIRCLE ( 'NONE', #42214, 0.009999999999999998473 ) ; +#86201 = PRESENTATION_STYLE_ASSIGNMENT (( #23957 ) ) ; +#86202 = PLANE ( 'NONE', #39848 ) ; +#86203 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86204 = VECTOR ( 'NONE', #17804, 1000.000000000000000 ) ; +#86205 = FILL_AREA_STYLE_COLOUR ( '', #87417 ) ; +#86206 = EDGE_LOOP ( 'NONE', ( #47503, #72831, #38165, #65248, #81885, #38155, #51703, #39344, #80344, #45076, #33716, #15738, #100752, #37809, #92493, #85079, #76644, #85972 ) ) ; +#86208 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86207 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86209 = ORIENTED_EDGE ( 'NONE', *, *, #36620, .F. ) ; +#86210 = ORIENTED_EDGE ( 'NONE', *, *, #97313, .T. ) ; +#86211 = SURFACE_SIDE_STYLE ('',( #55111 ) ) ; +#86212 = VECTOR ( 'NONE', #61152, 1000.000000000000000 ) ; +#86213 = EDGE_CURVE ( 'NONE', #93467, #53575, #90118, .T. ) ; +#86214 = VECTOR ( 'NONE', #3433, 999.9999999999998863 ) ; +#86215 = FILL_AREA_STYLE_COLOUR ( '', #67309 ) ; +#86216 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22400 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #124, #60452, #38945 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86218 = EDGE_LOOP ( 'NONE', ( #99792, #74447, #41764, #72633 ) ) ; +#86217 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#86219 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.149999999999970157, 0.000000000000000000 ) ) ; +#86220 = FILL_AREA_STYLE_COLOUR ( '', #9889 ) ; +#86221 = FILL_AREA_STYLE ('',( #79597 ) ) ; +#86222 = ORIENTED_EDGE ( 'NONE', *, *, #81103, .F. ) ; +#86223 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86224 = PLANE ( 'NONE', #72228 ) ; +#86225 = ORIENTED_EDGE ( 'NONE', *, *, #82554, .T. ) ; +#86226 = VERTEX_POINT ( 'NONE', #35032 ) ; +#86227 = ADVANCED_FACE ( 'NONE', ( #26863 ), #82487, .T. ) ; +#86229 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#86228 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86230 = CARTESIAN_POINT ( 'NONE', ( 1.793081130502420129, -1.407725713391660083, 0.8300000000000002931 ) ) ; +#86231 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86232 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16097 ) ) ; +#86233 = EDGE_CURVE ( 'NONE', #42687, #49062, #12440, .T. ) ; +#86234 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.2999999999999999889, -12.44500000000000028 ) ) ; +#86236 = LINE ( 'NONE', #62786, #98158 ) ; +#86235 = STYLED_ITEM ( 'NONE', ( #78884 ), #15216 ) ; +#86237 = LINE ( 'NONE', #16256, #17851 ) ; +#86238 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#86239 = ORIENTED_EDGE ( 'NONE', *, *, #78512, .T. ) ; +#86240 = SURFACE_STYLE_FILL_AREA ( #68883 ) ; +#86241 = SURFACE_STYLE_USAGE ( .BOTH. , #68884 ) ; +#86242 = ORIENTED_EDGE ( 'NONE', *, *, #60055, .T. ) ; +#86243 = EDGE_CURVE ( 'NONE', #4538, #14332, #58530, .T. ) ; +#86244 = FILL_AREA_STYLE ('',( #55144 ) ) ; +#86245 = CARTESIAN_POINT ( 'NONE', ( 1.795940028366769914, -1.028719707420159946, 0.8299999999999999600 ) ) ; +#86246 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86247 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77755, 'distance_accuracy_value', 'NONE'); +#86248 = PRESENTATION_STYLE_ASSIGNMENT (( #55154 ) ) ; +#86249 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#86250 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86251 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999992095, -3.500000000000000444, 0.000000000000000000 ) ) ; +#86252 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86253 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86254 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.700000000000000178, 0.000000000000000000 ) ) ; +#86255 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100771 ) ) ; +#86256 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86257 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74904 ) ) ; +#86258 = SURFACE_STYLE_FILL_AREA ( #39285 ) ; +#86259 = ADVANCED_FACE ( 'NONE', ( #80989 ), #36531, .T. ) ; +#86260 = EDGE_CURVE ( 'NONE', #48425, #83292, #76586, .T. ) ; +#86261 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86262 = SURFACE_STYLE_USAGE ( .BOTH. , #80151 ) ; +#86263 = CARTESIAN_POINT ( 'NONE', ( 2.300000000000000266, 3.123820061220055511, 0.000000000000000000 ) ) ; +#86264 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#86265 = FILL_AREA_STYLE ('',( #48505 ) ) ; +#86266 = FILL_AREA_STYLE ('',( #94416 ) ) ; +#86267 = PRESENTATION_STYLE_ASSIGNMENT (( #55170 ) ) ; +#86268 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53631 ) ) ; +#86269 = STYLED_ITEM ( 'NONE', ( #20498 ), #84996 ) ; +#86270 = AXIS2_PLACEMENT_3D ( 'NONE', #41610, #72738, #82426 ) ; +#86271 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81551, 'distance_accuracy_value', 'NONE'); +#86272 = ORIENTED_EDGE ( 'NONE', *, *, #65880, .T. ) ; +#86273 = FILL_AREA_STYLE ('',( #39821 ) ) ; +#86274 = STYLED_ITEM ( 'NONE', ( #74280 ), #56134 ) ; +#86275 = MANIFOLD_SOLID_BREP ( 'ÊäÈë57', #84345 ) ; +#86276 = EDGE_CURVE ( 'NONE', #27423, #85412, #84468, .T. ) ; +#86277 = ORIENTED_EDGE ( 'NONE', *, *, #20016, .T. ) ; +#86278 = FILL_AREA_STYLE ('',( #33176 ) ) ; +#86279 = FACE_OUTER_BOUND ( 'NONE', #77672, .T. ) ; +#86280 = FILL_AREA_STYLE ('',( #39303 ) ) ; +#86281 = SURFACE_SIDE_STYLE ('',( #8574 ) ) ; +#86282 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#86283 = FACE_OUTER_BOUND ( 'NONE', #25234, .T. ) ; +#86284 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#86285 = VECTOR ( 'NONE', #9329, 1000.000000000000000 ) ; +#86286 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999856 ) ) ; +#86287 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86288 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#86289 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47909 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33822, #57311, #627 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86290 = ORIENTED_EDGE ( 'NONE', *, *, #62764, .F. ) ; +#86291 = ORIENTED_EDGE ( 'NONE', *, *, #77497, .T. ) ; +#86292 = VECTOR ( 'NONE', #42825, 1000.000000000000000 ) ; +#86293 = FILL_AREA_STYLE ('',( #46978 ) ) ; +#86294 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86295 = SURFACE_STYLE_USAGE ( .BOTH. , #70457 ) ; +#86296 = STYLED_ITEM ( 'NONE', ( #72321 ), #42554 ) ; +#86297 = FILL_AREA_STYLE ('',( #46456 ) ) ; +#86298 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86299 = SURFACE_STYLE_USAGE ( .BOTH. , #22497 ) ; +#86300 = CARTESIAN_POINT ( 'NONE', ( 6.650674999999999670, 1.696237999999999913, 0.8991599999999999593 ) ) ; +#86301 = VECTOR ( 'NONE', #6559, 1000.000000000000000 ) ; +#86302 = VERTEX_POINT ( 'NONE', #19681 ) ; +#86303 = LINE ( 'NONE', #24046, #94060 ) ; +#86304 = ORIENTED_EDGE ( 'NONE', *, *, #98296, .T. ) ; +#86305 = ADVANCED_FACE ( 'NONE', ( #60520 ), #85471, .F. ) ; +#86306 = ORIENTED_EDGE ( 'NONE', *, *, #970, .T. ) ; +#86307 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2175 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21463, #28625, #11706 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86308 = PRESENTATION_STYLE_ASSIGNMENT (( #54693 ) ) ; +#86309 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999266420, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#86310 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29251 ) ) ; +#86311 = LINE ( 'NONE', #94955, #46245 ) ; +#86312 = EDGE_CURVE ( 'NONE', #12578, #59551, #69629, .T. ) ; +#86313 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86314 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 1.965875379150715025E-17, 0.4000000000000000777 ) ) ; +#86315 = EDGE_CURVE ( 'NONE', #20861, #13932, #7058, .T. ) ; +#86317 = ORIENTED_EDGE ( 'NONE', *, *, #27180, .T. ) ; +#86316 = VERTEX_POINT ( 'NONE', #37528 ) ; +#86318 = FACE_OUTER_BOUND ( 'NONE', #495, .T. ) ; +#86320 = VECTOR ( 'NONE', #50437, 1000.000000000000000 ) ; +#86319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86321 = FILL_AREA_STYLE ('',( #78653 ) ) ; +#86322 = ORIENTED_EDGE ( 'NONE', *, *, #60018, .F. ) ; +#86323 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86324 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #68713, #46222, #84556, #15069 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#86326 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#86325 = CARTESIAN_POINT ( 'NONE', ( 5.696080875125044685, 3.570071124874956592, 0.8648700000000000276 ) ) ; +#86327 = ORIENTED_EDGE ( 'NONE', *, *, #60698, .F. ) ; +#86328 = ORIENTED_EDGE ( 'NONE', *, *, #29041, .F. ) ; +#86329 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261923999999999602, 0.8991599999999999593 ) ) ; +#86330 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86331 = FILL_AREA_STYLE ('',( #30673 ) ) ; +#86332 = CARTESIAN_POINT ( 'NONE', ( -0.2194392452033120111, -1.042364979248350032, 0.8300000000000000711 ) ) ; +#86333 = VECTOR ( 'NONE', #66094, 1000.000000000000000 ) ; +#86334 = SURFACE_SIDE_STYLE ('',( #78183 ) ) ; +#86335 = SURFACE_STYLE_FILL_AREA ( #15342 ) ; +#86336 = VERTEX_POINT ( 'NONE', #83482 ) ; +#86337 = ORIENTED_EDGE ( 'NONE', *, *, #34097, .F. ) ; +#86338 = ORIENTED_EDGE ( 'NONE', *, *, #27954, .T. ) ; +#86339 = LINE ( 'NONE', #63885, #98111 ) ; +#86340 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70222 ), #24651 ) ; +#86341 = STYLED_ITEM ( 'NONE', ( #59528 ), #92710 ) ; +#86342 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53547 ) ) ; +#86343 = EDGE_CURVE ( 'NONE', #42769, #35018, #62021, .T. ) ; +#86345 = ORIENTED_EDGE ( 'NONE', *, *, #51162, .F. ) ; +#86344 = CARTESIAN_POINT ( 'NONE', ( 1.036363636363639928, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#86346 = AXIS2_PLACEMENT_3D ( 'NONE', #59615, #91209, #58597 ) ; +#86347 = CIRCLE ( 'NONE', #50532, 0.09999999999999939493 ) ; +#86348 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86349 = FACE_OUTER_BOUND ( 'NONE', #88537, .T. ) ; +#86350 = ORIENTED_EDGE ( 'NONE', *, *, #97016, .T. ) ; +#86351 = VECTOR ( 'NONE', #11723, 1000.000000000000114 ) ; +#86352 = SURFACE_SIDE_STYLE ('',( #31725 ) ) ; +#86353 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86354 = VERTEX_POINT ( 'NONE', #5820 ) ; +#86355 = EDGE_CURVE ( 'NONE', #26854, #54178, #23088, .T. ) ; +#86356 = CIRCLE ( 'NONE', #48914, 0.4459546481032609644 ) ; +#86357 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.049999999999999822 ) ) ; +#86359 = SURFACE_STYLE_FILL_AREA ( #55250 ) ; +#86358 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73335 ) ) ; +#86360 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#86361 = EDGE_CURVE ( 'NONE', #88228, #48290, #37020, .T. ) ; +#86363 = ORIENTED_EDGE ( 'NONE', *, *, #62097, .F. ) ; +#86362 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86364 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86365 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 1.500000000000000000, 0.000000000000000000 ) ) ; +#86367 = CARTESIAN_POINT ( 'NONE', ( 1.612727879620370119, -1.495500525511030077, 0.8299999999999999600 ) ) ; +#86366 = LINE ( 'NONE', #63905, #5609 ) ; +#86368 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #79759, #9701, #50632, #58804 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#86369 = CARTESIAN_POINT ( 'NONE', ( 1.581863761282799929, -1.087576819458450084, 0.8299999999999990719 ) ) ; +#86370 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57038 ) ) ; +#86371 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#86372 = LINE ( 'NONE', #77700, #54457 ) ; +#86373 = ORIENTED_EDGE ( 'NONE', *, *, #93621, .F. ) ; +#86374 = EDGE_CURVE ( 'NONE', #48342, #16606, #8289, .T. ) ; +#86375 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86376 = LINE ( 'NONE', #24113, #83883 ) ; +#86377 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86378 = CARTESIAN_POINT ( 'NONE', ( 1.279293756061498755, -0.9562692539047544793, 0.8100000000000172617 ) ) ; +#86379 = PRESENTATION_STYLE_ASSIGNMENT (( #87886 ) ) ; +#86381 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86380 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86382 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#86383 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#86384 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86385 = FACE_OUTER_BOUND ( 'NONE', #60318, .T. ) ; +#86386 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86387 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86388 = VERTEX_POINT ( 'NONE', #64019 ) ; +#86389 = FILL_AREA_STYLE_COLOUR ( '', #38133 ) ; +#86390 = EDGE_CURVE ( 'NONE', #55589, #45825, #49215, .T. ) ; +#86391 = ORIENTED_EDGE ( 'NONE', *, *, #68268, .F. ) ; +#86392 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86393 = SURFACE_SIDE_STYLE ('',( #9709 ) ) ; +#86395 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86394 = SURFACE_STYLE_FILL_AREA ( #85885 ) ; +#86397 = EDGE_CURVE ( 'NONE', #1339, #17228, #79856, .T. ) ; +#86396 = PLANE ( 'NONE', #47990 ) ; +#86398 = STYLED_ITEM ( 'NONE', ( #60198 ), #29223 ) ; +#86399 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17643, 'distance_accuracy_value', 'NONE'); +#86400 = ORIENTED_EDGE ( 'NONE', *, *, #100897, .F. ) ; +#86401 = CARTESIAN_POINT ( 'NONE', ( 1.767907037466160070, -0.9096959278232360502, 0.8100000000000008304 ) ) ; +#86402 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.01499999999999998730, -0.1400000000000000688 ) ) ; +#86403 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86404 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86405 = EDGE_CURVE ( 'NONE', #60603, #13162, #55381, .T. ) ; +#86406 = PRESENTATION_STYLE_ASSIGNMENT (( #9217 ) ) ; +#86407 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#86408 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86409 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#86410 = EDGE_CURVE ( 'NONE', #26148, #20813, #62526, .T. ) ; +#86411 = CARTESIAN_POINT ( 'NONE', ( -0.008621852316070110350, -0.9218577280486121017, 0.8100000000000000533 ) ) ; +#86412 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #87319, #27078 ), + ( #64350, #35252 ), + ( #96461, #26566 ), + ( #65867, #50568 ), + ( #87829, #3578 ), + ( #26069, #66364 ), + ( #17865, #3071 ), + ( #81204, #88838 ), + ( #42390, #97468 ), + ( #73527, #51065 ), + ( #50070, #57737 ), + ( #18867, #64851 ), + ( #34741, #4068 ), + ( #42878, #2571 ), + ( #88334, #10625 ), + ( #18361, #27575 ), + ( #56722, #96968 ), + ( #49047, #41883 ), + ( #58240, #89340 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07045709961185249448, 0.1383447481512539989, 0.2028990021023260037, 0.2654810950381250034, 0.3258772383107860215, 0.3852050427271530020, 0.4429358768679579894, 0.5002805841468770387, 0.5571221970013150449, 0.6137119875414840386, 0.6717416701598909468, 0.7307879491163220553, 0.7928531519886019563, 0.8578850024924840056, 0.9271793188984439604, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#86413 = PRESENTATION_STYLE_ASSIGNMENT (( #46582 ) ) ; +#86414 = STYLED_ITEM ( 'NONE', ( #5432 ), #86134 ) ; +#86415 = AXIS2_PLACEMENT_3D ( 'NONE', #80763, #63921, #95520 ) ; +#86416 = PLANE ( 'NONE', #6138 ) ; +#86417 = LINE ( 'NONE', #55305, #17697 ) ; +#86418 = ORIENTED_EDGE ( 'NONE', *, *, #10020, .T. ) ; +#86419 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86420 = VERTEX_POINT ( 'NONE', #87004 ) ; +#86421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16104 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14728, #93341, #21427 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86422 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86423 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86425 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#86424 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92183 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70460, #93909, #11620 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86426 = VECTOR ( 'NONE', #41061, 1000.000000000000000 ) ; +#86427 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86428 = SURFACE_STYLE_FILL_AREA ( #31793 ) ; +#86429 = CARTESIAN_POINT ( 'NONE', ( 0.03349564727623650928, -1.152628822534790043, 0.8100000000000000533 ) ) ; +#86430 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.7000000000000000666, -0.02000000000001045039 ) ) ; +#86431 = EDGE_LOOP ( 'NONE', ( #77939, #62385, #69062, #9430 ) ) ; +#86432 = FILL_AREA_STYLE ('',( #46601 ) ) ; +#86433 = FILL_AREA_STYLE_COLOUR ( '', #56949 ) ; +#86434 = AXIS2_PLACEMENT_3D ( 'NONE', #46367, #940, #32604 ) ; +#86435 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86436 = ORIENTED_EDGE ( 'NONE', *, *, #41872, .T. ) ; +#86438 = SURFACE_SIDE_STYLE ('',( #2693 ) ) ; +#86437 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86439 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18105 ), #31189 ) ; +#86440 = EDGE_LOOP ( 'NONE', ( #7263, #53282, #96848, #12890 ) ) ; +#86441 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86442 = LINE ( 'NONE', #77253, #18484 ) ; +#86443 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#86444 = SURFACE_SIDE_STYLE ('',( #63491 ) ) ; +#86445 = EDGE_CURVE ( 'NONE', #72772, #69488, #1210, .T. ) ; +#86446 = ORIENTED_EDGE ( 'NONE', *, *, #31854, .T. ) ; +#86447 = VECTOR ( 'NONE', #6881, 1000.000000000000114 ) ; +#86448 = SURFACE_STYLE_FILL_AREA ( #96089 ) ; +#86449 = FILL_AREA_STYLE ('',( #24189 ) ) ; +#86450 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#86451 = EDGE_CURVE ( 'NONE', #86336, #52672, #40553, .T. ) ; +#86452 = SURFACE_SIDE_STYLE ('',( #55343 ) ) ; +#86453 = MANIFOLD_SOLID_BREP ( 'ÊäÈë162', #89310 ) ; +#86454 = ORIENTED_EDGE ( 'NONE', *, *, #27860, .F. ) ; +#86455 = VECTOR ( 'NONE', #23953, 1000.000000000000000 ) ; +#86456 = PRESENTATION_STYLE_ASSIGNMENT (( #1714 ) ) ; +#86457 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86458 = CIRCLE ( 'NONE', #58805, 0.009999999999999998473 ) ; +#86459 = FILL_AREA_STYLE ('',( #38990 ) ) ; +#86460 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#86461 = VERTEX_POINT ( 'NONE', #8785 ) ; +#86462 = ORIENTED_EDGE ( 'NONE', *, *, #83973, .F. ) ; +#86463 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86464 = ORIENTED_EDGE ( 'NONE', *, *, #27667, .T. ) ; +#86465 = VECTOR ( 'NONE', #23261, 1000.000000000000000 ) ; +#86466 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86467 = EDGE_CURVE ( 'NONE', #55276, #76681, #47173, .T. ) ; +#86468 = ORIENTED_EDGE ( 'NONE', *, *, #5603, .T. ) ; +#86470 = ORIENTED_EDGE ( 'NONE', *, *, #9392, .T. ) ; +#86469 = SURFACE_STYLE_FILL_AREA ( #24209 ) ; +#86471 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.200000000000000178, 0.000000000000000000 ) ) ; +#86472 = FILL_AREA_STYLE_COLOUR ( '', #18751 ) ; +#86473 = SURFACE_STYLE_USAGE ( .BOTH. , #95104 ) ; +#86474 = ORIENTED_EDGE ( 'NONE', *, *, #12665, .F. ) ; +#86475 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#86476 = CARTESIAN_POINT ( 'NONE', ( 1.820901995646820204, -1.357122040133029950, 0.8099999999999997202 ) ) ; +#86477 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#86478 = ORIENTED_EDGE ( 'NONE', *, *, #63630, .F. ) ; +#86479 = ADVANCED_FACE ( 'NONE', ( #41552 ), #39516, .T. ) ; +#86480 = PLANE ( 'NONE', #87241 ) ; +#86481 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.950000000000000178, 0.000000000000000000 ) ) ; +#86482 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86483 = ORIENTED_EDGE ( 'NONE', *, *, #13367, .F. ) ; +#86485 = PLANE ( 'NONE', #63374 ) ; +#86484 = FILL_AREA_STYLE ('',( #54340 ) ) ; +#86486 = ORIENTED_EDGE ( 'NONE', *, *, #91417, .F. ) ; +#86487 = VECTOR ( 'NONE', #85590, 1000.000000000000000 ) ; +#86488 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86490 = PRESENTATION_STYLE_ASSIGNMENT (( #70143 ) ) ; +#86489 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#86491 = FILL_AREA_STYLE_COLOUR ( '', #80026 ) ; +#86492 = ADVANCED_FACE ( 'NONE', ( #51728 ), #12827, .F. ) ; +#86493 = STYLED_ITEM ( 'NONE', ( #86099 ), #57754 ) ; +#86494 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34343 ), #42486 ) ; +#86495 = SURFACE_STYLE_FILL_AREA ( #14485 ) ; +#86496 = ORIENTED_EDGE ( 'NONE', *, *, #43403, .T. ) ; +#86497 = FACE_OUTER_BOUND ( 'NONE', #40098, .T. ) ; +#86498 = ADVANCED_FACE ( 'NONE', ( #35423 ), #4241, .T. ) ; +#86499 = PLANE ( 'NONE', #27912 ) ; +#86500 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86501 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000003803, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#86502 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78994 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44246, #91716, #90224 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86503 = AXIS2_PLACEMENT_3D ( 'NONE', #93763, #93267, #54007 ) ; +#86504 = CARTESIAN_POINT ( 'NONE', ( -0.9526471110344909565, -0.9920916311794309994, 0.8299999999999999600 ) ) ; +#86505 = STYLED_ITEM ( 'NONE', ( #69142 ), #65588 ) ; +#86506 = FACE_OUTER_BOUND ( 'NONE', #24239, .T. ) ; +#86507 = PLANE ( 'NONE', #60981 ) ; +#86508 = SURFACE_STYLE_USAGE ( .BOTH. , #69645 ) ; +#86509 = EDGE_CURVE ( 'NONE', #15757, #56990, #57912, .T. ) ; +#86510 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#86511 = LINE ( 'NONE', #54373, #90108 ) ; +#86512 = ADVANCED_FACE ( 'NONE', ( #89016 ), #81384, .T. ) ; +#86513 = LINE ( 'NONE', #39538, #85841 ) ; +#86514 = ORIENTED_EDGE ( 'NONE', *, *, #74302, .T. ) ; +#86515 = CARTESIAN_POINT ( 'NONE', ( -1.277337950986729975, -1.102553831183370026, 0.8300000000000002931 ) ) ; +#86516 = STYLED_ITEM ( 'NONE', ( #49131 ), #2128 ) ; +#86517 = FILL_AREA_STYLE ('',( #64051 ) ) ; +#86518 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#86519 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59407, 'distance_accuracy_value', 'NONE'); +#86520 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23626 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69489, #30192, #61392 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86521 = ADVANCED_FACE ( 'NONE', ( #99578 ), #29718, .F. ) ; +#86523 = EDGE_CURVE ( 'NONE', #21645, #44988, #59657, .T. ) ; +#86522 = SURFACE_STYLE_FILL_AREA ( #63055 ) ; +#86524 = PRESENTATION_STYLE_ASSIGNMENT (( #87032 ) ) ; +#86525 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#86526 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #31240, #61906, #31743, #46012 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#86527 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86528 = VERTEX_POINT ( 'NONE', #96892 ) ; +#86529 = SURFACE_SIDE_STYLE ('',( #55911 ) ) ; +#86530 = CARTESIAN_POINT ( 'NONE', ( 3.794707603699269956E-16, 1.393372100993099938, 0.8100000000000000533 ) ) ; +#86531 = EDGE_CURVE ( 'NONE', #25227, #76054, #42620, .T. ) ; +#86532 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#86533 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86534 = FACE_OUTER_BOUND ( 'NONE', #20678, .T. ) ; +#86535 = SURFACE_STYLE_USAGE ( .BOTH. , #47220 ) ; +#86536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86537 = FILL_AREA_STYLE_COLOUR ( '', #23502 ) ; +#86538 = EDGE_CURVE ( 'NONE', #71259, #7596, #2994, .T. ) ; +#86539 = PRESENTATION_STYLE_ASSIGNMENT (( #39067 ) ) ; +#86540 = LINE ( 'NONE', #10339, #46851 ) ; +#86541 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#86542 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86543 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#86544 = ORIENTED_EDGE ( 'NONE', *, *, #58363, .F. ) ; +#86545 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#86546 = EDGE_LOOP ( 'NONE', ( #30442, #67236, #20803, #34540, #47170, #53091 ) ) ; +#86547 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96348 ) ) ; +#86548 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#86549 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.100000000000000089, 0.1829999999999959992 ) ) ; +#86550 = SURFACE_STYLE_USAGE ( .BOTH. , #55440 ) ; +#86551 = PRESENTATION_STYLE_ASSIGNMENT (( #55441 ) ) ; +#86552 = CARTESIAN_POINT ( 'NONE', ( -0.1381505133853417056, 2.561284075926966608, 0.8100000000000000533 ) ) ; +#86553 = CARTESIAN_POINT ( 'NONE', ( -1.000284964254319897, -1.196758459236680006, 0.8100000000000000533 ) ) ; +#86554 = ORIENTED_EDGE ( 'NONE', *, *, #76711, .T. ) ; +#86555 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86556 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.476179938779914824, 0.000000000000000000 ) ) ; +#86557 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86558 = PRESENTATION_STYLE_ASSIGNMENT (( #26812 ) ) ; +#86559 = ORIENTED_EDGE ( 'NONE', *, *, #29252, .F. ) ; +#86560 = SURFACE_STYLE_USAGE ( .BOTH. , #64094 ) ; +#86561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41132 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1748, #33393, #9303 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86562 = STYLED_ITEM ( 'NONE', ( #59196 ), #95169 ) ; +#86563 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#86564 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86565 = ORIENTED_EDGE ( 'NONE', *, *, #66571, .F. ) ; +#86566 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11908 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #581, #12946, #46532 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86567 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#86568 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6176, 'distance_accuracy_value', 'NONE'); +#86569 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#86570 = EDGE_CURVE ( 'NONE', #14799, #20765, #96390, .T. ) ; +#86571 = FACE_OUTER_BOUND ( 'NONE', #34245, .T. ) ; +#86572 = STYLED_ITEM ( 'NONE', ( #37506 ), #7377 ) ; +#86573 = ORIENTED_EDGE ( 'NONE', *, *, #66974, .F. ) ; +#86574 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86575 = VERTEX_POINT ( 'NONE', #57144 ) ; +#86576 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86577 = LINE ( 'NONE', #65108, #14441 ) ; +#86578 = AXIS2_PLACEMENT_3D ( 'NONE', #82412, #52768, #67543 ) ; +#86579 = SURFACE_STYLE_USAGE ( .BOTH. , #56489 ) ; +#86580 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86581 = LINE ( 'NONE', #65478, #75794 ) ; +#86582 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86583 = AXIS2_PLACEMENT_3D ( 'NONE', #26436, #19246, #80069 ) ; +#86584 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40989 ), #45802 ) ; +#86585 = ORIENTED_EDGE ( 'NONE', *, *, #9148, .F. ) ; +#86586 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20167, 'distance_accuracy_value', 'NONE'); +#86587 = DIRECTION ( 'NONE', ( 0.7071060119555152568, 0.7071075504167430026, 0.000000000000000000 ) ) ; +#86588 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#86589 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86590 = ORIENTED_EDGE ( 'NONE', *, *, #74934, .F. ) ; +#86591 = EDGE_CURVE ( 'NONE', #12201, #90990, #94828, .T. ) ; +#86592 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86593 = LINE ( 'NONE', #26346, #97208 ) ; +#86594 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23058 ) ) ; +#86595 = ORIENTED_EDGE ( 'NONE', *, *, #48164, .F. ) ; +#86597 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#86596 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86598 = ORIENTED_EDGE ( 'NONE', *, *, #92221, .T. ) ; +#86599 = ORIENTED_EDGE ( 'NONE', *, *, #62186, .T. ) ; +#86600 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86602 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4600000000000000200, -0.2250000000000000333 ) ) ; +#86601 = SURFACE_SIDE_STYLE ('',( #8400 ) ) ; +#86603 = FILL_AREA_STYLE ('',( #32501 ) ) ; +#86604 = FILL_AREA_STYLE_COLOUR ( '', #26 ) ; +#86606 = EDGE_LOOP ( 'NONE', ( #53193, #92474, #35154, #96759 ) ) ; +#86605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94743 ), #73577 ) ; +#86607 = FILL_AREA_STYLE ('',( #78946 ) ) ; +#86608 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155857000000000134, 0.8991599999999999593 ) ) ; +#86609 = LINE ( 'NONE', #76941, #40200 ) ; +#86610 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86611 = ORIENTED_EDGE ( 'NONE', *, *, #28419, .F. ) ; +#86612 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86613 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86614 = ORIENTED_EDGE ( 'NONE', *, *, #36874, .F. ) ; +#86615 = EDGE_LOOP ( 'NONE', ( #55860, #71384, #36509, #82711 ) ) ; +#86617 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#86616 = FACE_OUTER_BOUND ( 'NONE', #19537, .T. ) ; +#86618 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#86619 = MANIFOLD_SOLID_BREP ( 'ÊäÈë21', #4521 ) ; +#86620 = SURFACE_STYLE_USAGE ( .BOTH. , #78453 ) ; +#86621 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86622 = CIRCLE ( 'NONE', #21383, 0.009999999999999998473 ) ; +#86623 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86624 = CARTESIAN_POINT ( 'NONE', ( -0.08150952889499120391, -1.159841243706410063, 0.8100000000000000533 ) ) ; +#86625 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100934 ) ; +#86626 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86627 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#86628 = AXIS2_PLACEMENT_3D ( 'NONE', #26742, #44039, #4726 ) ; +#86629 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86630 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49117 ), #84936 ) ; +#86631 = VERTEX_POINT ( 'NONE', #64772 ) ; +#86632 = PLANE ( 'NONE', #13766 ) ; +#86633 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 10.26637200000000050, 0.8991599999999999593 ) ) ; +#86635 = CARTESIAN_POINT ( 'NONE', ( -0.9195163728965894956, -1.395329896795636238, 0.8099999999996970734 ) ) ; +#86634 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8891 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41321, #1997, #31620 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86636 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86637 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86639 = ADVANCED_FACE ( 'NONE', ( #81127 ), #62911, .T. ) ; +#86638 = FACE_OUTER_BOUND ( 'NONE', #94224, .T. ) ; +#86640 = VECTOR ( 'NONE', #64421, 1000.000000000000000 ) ; +#86641 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86642 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86643 = LINE ( 'NONE', #71834, #27328 ) ; +#86644 = FACE_OUTER_BOUND ( 'NONE', #39779, .T. ) ; +#86645 = ORIENTED_EDGE ( 'NONE', *, *, #17398, .F. ) ; +#86646 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34568 ) ) ; +#86647 = FACE_OUTER_BOUND ( 'NONE', #12968, .T. ) ; +#86648 = FACE_OUTER_BOUND ( 'NONE', #50574, .T. ) ; +#86649 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86650 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66294 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87300, #9607, #33187 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86651 = FACE_OUTER_BOUND ( 'NONE', #53110, .T. ) ; +#86652 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80123 ), #197 ) ; +#86653 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.6999999999999999556, -13.15000000000000036 ) ) ; +#86654 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86655 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#86656 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86657 = ADVANCED_FACE ( 'NONE', ( #11568 ), #74959, .T. ) ; +#86658 = CARTESIAN_POINT ( 'NONE', ( 0.6689326298701294693, 0.6899999999999999467, 0.4397321428571430157 ) ) ; +#86659 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86660 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988787, -3.149999999999979927, 0.000000000000000000 ) ) ; +#86661 = LINE ( 'NONE', #73368, #63497 ) ; +#86662 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.699999999999999956, 0.1829999999999920024 ) ) ; +#86663 = VECTOR ( 'NONE', #84548, 1000.000000000000000 ) ; +#86664 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86665 = PLANE ( 'NONE', #52873 ) ; +#86666 = VECTOR ( 'NONE', #72280, 1000.000000000000000 ) ; +#86667 = SURFACE_SIDE_STYLE ('',( #16671 ) ) ; +#86668 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86669 = PRESENTATION_STYLE_ASSIGNMENT (( #24921 ) ) ; +#86670 = FILL_AREA_STYLE_COLOUR ( '', #23158 ) ; +#86671 = VERTEX_POINT ( 'NONE', #97388 ) ; +#86672 = FILL_AREA_STYLE ('',( #24925 ) ) ; +#86673 = LINE ( 'NONE', #17209, #42139 ) ; +#86674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86675 = SURFACE_SIDE_STYLE ('',( #23382 ) ) ; +#86676 = AXIS2_PLACEMENT_3D ( 'NONE', #87545, #89058, #48762 ) ; +#86677 = LINE ( 'NONE', #76610, #38782 ) ; +#86678 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86679 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73640 ) ) ; +#86680 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.299999999999999822, 1.048695503451051965E-76 ) ) ; +#86681 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -8.987602329035836718E-17, -0.6199999999999999956 ) ) ; +#86682 = ADVANCED_FACE ( 'NONE', ( #13079 ), #75445, .F. ) ; +#86683 = ORIENTED_EDGE ( 'NONE', *, *, #94236, .F. ) ; +#86684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86685 = AXIS2_PLACEMENT_3D ( 'NONE', #55823, #77782, #32334 ) ; +#86686 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8099999999999438760 ) ) ; +#86687 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, -0.1499999999999999667, -0.01999999999999999695 ) ) ; +#86688 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86689 = EDGE_CURVE ( 'NONE', #436, #97591, #43296, .T. ) ; +#86690 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.216666666666666785, 0.000000000000000000 ) ) ; +#86691 = ORIENTED_EDGE ( 'NONE', *, *, #41310, .T. ) ; +#86692 = EDGE_LOOP ( 'NONE', ( #50692, #48348, #437, #95218 ) ) ; +#86693 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1936 ), #14923 ) ; +#86694 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#86695 = ORIENTED_EDGE ( 'NONE', *, *, #65041, .T. ) ; +#86696 = CARTESIAN_POINT ( 'NONE', ( 11.97415200000000013, 11.33668300000000073, 0.8991599999999999593 ) ) ; +#86697 = FILL_AREA_STYLE ('',( #63247 ) ) ; +#86698 = PRESENTATION_STYLE_ASSIGNMENT (( #77513 ) ) ; +#86699 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#86700 = AXIS2_PLACEMENT_3D ( 'NONE', #30986, #339, #45269 ) ; +#86701 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.100000000000000089, 0.1829999999999619709 ) ) ; +#86702 = STYLED_ITEM ( 'NONE', ( #18319 ), #95799 ) ; +#86703 = SHAPE_DEFINITION_REPRESENTATION ( #7425, #72236 ) ; +#86705 = ORIENTED_EDGE ( 'NONE', *, *, #78824, .T. ) ; +#86704 = ORIENTED_EDGE ( 'NONE', *, *, #47094, .T. ) ; +#86706 = ORIENTED_EDGE ( 'NONE', *, *, #13226, .F. ) ; +#86707 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38813 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5104, #4135, #74091 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86708 = VERTEX_POINT ( 'NONE', #66769 ) ; +#86709 = CARTESIAN_POINT ( 'NONE', ( 3.822248124875013531, 4.524665124875012268, 0.8648700000000000276 ) ) ; +#86710 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23133, 'distance_accuracy_value', 'NONE'); +#86711 = STYLED_ITEM ( 'NONE', ( #31461 ), #10946 ) ; +#86712 = LINE ( 'NONE', #16725, #75767 ) ; +#86713 = EDGE_LOOP ( 'NONE', ( #43878, #57335, #90542, #85615 ) ) ; +#86714 = STYLED_ITEM ( 'NONE', ( #28118 ), #7649 ) ; +#86715 = ADVANCED_FACE ( 'NONE', ( #4484 ), #82620, .T. ) ; +#86716 = SURFACE_STYLE_USAGE ( .BOTH. , #57626 ) ; +#86717 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#86718 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01085786437626904202, 0.1434314575050762153 ) ) ; +#86719 = ORIENTED_EDGE ( 'NONE', *, *, #42800, .T. ) ; +#86721 = FILL_AREA_STYLE ('',( #38741 ) ) ; +#86720 = FILL_AREA_STYLE_COLOUR ( '', #31846 ) ; +#86722 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73682 ) ) ; +#86723 = EDGE_LOOP ( 'NONE', ( #46343, #16003, #34440, #89247 ) ) ; +#86725 = CARTESIAN_POINT ( 'NONE', ( 0.9899999999999999911, 0.1200000000000003147, 0.3499999999999999778 ) ) ; +#86724 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86726 = EDGE_CURVE ( 'NONE', #52597, #82814, #16143, .T. ) ; +#86727 = ORIENTED_EDGE ( 'NONE', *, *, #78053, .F. ) ; +#86728 = ORIENTED_EDGE ( 'NONE', *, *, #1934, .T. ) ; +#86729 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#86730 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86731 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86733 = ORIENTED_EDGE ( 'NONE', *, *, #13106, .T. ) ; +#86732 = CYLINDRICAL_SURFACE ( 'NONE', #21753, 0.1000000000000000194 ) ; +#86734 = FILL_AREA_STYLE_COLOUR ( '', #100239 ) ; +#86735 = CARTESIAN_POINT ( 'NONE', ( 9.214665000000000106, 10.20293700000000037, 0.8991599999999999593 ) ) ; +#86736 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 8.385469000000000506, 0.8648700000000000276 ) ) ; +#86737 = SURFACE_SIDE_STYLE ('',( #85712 ) ) ; +#86738 = ORIENTED_EDGE ( 'NONE', *, *, #11296, .F. ) ; +#86740 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 15.15000000000000036, 0.000000000000000000 ) ) ; +#86739 = SURFACE_STYLE_FILL_AREA ( #44514 ) ; +#86741 = ORIENTED_EDGE ( 'NONE', *, *, #7600, .T. ) ; +#86742 = VERTEX_POINT ( 'NONE', #47315 ) ; +#86743 = ADVANCED_FACE ( 'NONE', ( #78459 ), #8419, .T. ) ; +#86745 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999734, 0.6892893218813450629, 0.8000000000000000444 ) ) ; +#86744 = SURFACE_STYLE_FILL_AREA ( #17779 ) ; +#86746 = CARTESIAN_POINT ( 'NONE', ( 1.743271607193970008, -1.437850337629750008, 0.8300000000000002931 ) ) ; +#86747 = EDGE_CURVE ( 'NONE', #48677, #15757, #62165, .T. ) ; +#86748 = PLANE ( 'NONE', #52961 ) ; +#86749 = VECTOR ( 'NONE', #49644, 1000.000000000000000 ) ; +#86750 = CARTESIAN_POINT ( 'NONE', ( -0.5282008442508040469, -1.258308808185959915, 0.8100000000000000533 ) ) ; +#86752 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36261 ) ) ; +#86751 = SURFACE_SIDE_STYLE ('',( #56132 ) ) ; +#86753 = CARTESIAN_POINT ( 'NONE', ( 8.687142500500176112, 2.261923500500174544, 0.8991599999999999593 ) ) ; +#86754 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #10563, 'distance_accuracy_value', 'NONE'); +#86755 = SURFACE_SIDE_STYLE ('',( #87247 ) ) ; +#86756 = VERTEX_POINT ( 'NONE', #46793 ) ; +#86757 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86758 = CARTESIAN_POINT ( 'NONE', ( 0.06704264972532250622, -1.237898259965849901, 0.8299999999999999600 ) ) ; +#86759 = VERTEX_POINT ( 'NONE', #7921 ) ; +#86760 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#86761 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#86763 = EDGE_CURVE ( 'NONE', #54195, #60372, #62665, .T. ) ; +#86762 = SURFACE_STYLE_USAGE ( .BOTH. , #55146 ) ; +#86764 = PLANE ( 'NONE', #51204 ) ; +#86765 = CARTESIAN_POINT ( 'NONE', ( 1.600000000000000089, 0.1600000000000000033, 1.129999999999999893 ) ) ; +#86766 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86767 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86768 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.7000000000000003997, 1.048695503451053346E-76 ) ) ; +#86769 = DIRECTION ( 'NONE', ( -0.7071060119555143686, 0.7071075504167438908, 0.000000000000000000 ) ) ; +#86770 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32984 ) ) ; +#86771 = CIRCLE ( 'NONE', #55812, 0.09407705479135430870 ) ; +#86772 = CARTESIAN_POINT ( 'NONE', ( -1.276180882027730279, -0.9985765647821309710, 0.8299999999999998490 ) ) ; +#86773 = LINE ( 'NONE', #26017, #91368 ) ; +#86774 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#86775 = VECTOR ( 'NONE', #82851, 1000.000000000000000 ) ; +#86776 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86777 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36208 ), #31298 ) ; +#86778 = EDGE_CURVE ( 'NONE', #44988, #50972, #41359, .T. ) ; +#86779 = VECTOR ( 'NONE', #97791, 1000.000000000000000 ) ; +#86780 = LINE ( 'NONE', #1006, #6441 ) ; +#86781 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#86782 = CARTESIAN_POINT ( 'NONE', ( 0.5096387987012980236, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#86783 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86784 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, -0.02000000000000000042 ) ) ; +#86785 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#86786 = AXIS2_PLACEMENT_3D ( 'NONE', #14133, #99829, #75463 ) ; +#86787 = VECTOR ( 'NONE', #37127, 1000.000000000000000 ) ; +#86788 = ORIENTED_EDGE ( 'NONE', *, *, #600, .T. ) ; +#86789 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86790 = SURFACE_SIDE_STYLE ('',( #24540 ) ) ; +#86791 = STYLED_ITEM ( 'NONE', ( #31734 ), #7632 ) ; +#86793 = MANIFOLD_SOLID_BREP ( 'ÊäÈë3', #94142 ) ; +#86792 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83641, 'distance_accuracy_value', 'NONE'); +#86794 = EDGE_LOOP ( 'NONE', ( #65631, #15193, #2112, #50536 ) ) ; +#86795 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23001, 'distance_accuracy_value', 'NONE'); +#86796 = CARTESIAN_POINT ( 'NONE', ( 0.3664818191693184901, -1.221528794467885648, 0.8100000000000001643 ) ) ; +#86797 = SURFACE_STYLE_USAGE ( .BOTH. , #7076 ) ; +#86798 = STYLED_ITEM ( 'NONE', ( #28415 ), #66590 ) ; +#86799 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2808578643762690286, -0.1399999999999999856 ) ) ; +#86800 = FACE_OUTER_BOUND ( 'NONE', #35452, .T. ) ; +#86801 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#86802 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73762 ), #68830 ) ; +#86803 = ADVANCED_FACE ( 'NONE', ( #9444 ), #1362, .T. ) ; +#86804 = VERTEX_POINT ( 'NONE', #96270 ) ; +#86805 = FILL_AREA_STYLE ('',( #11494 ) ) ; +#86806 = ORIENTED_EDGE ( 'NONE', *, *, #94900, .T. ) ; +#86807 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86808 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29539, 'distance_accuracy_value', 'NONE'); +#86809 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86810 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#86811 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86812 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#86813 = LINE ( 'NONE', #2556, #95119 ) ; +#86814 = EDGE_LOOP ( 'NONE', ( #30320, #42308, #45324, #3476 ) ) ; +#86815 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86816 = SURFACE_STYLE_USAGE ( .BOTH. , #57724 ) ; +#86817 = ORIENTED_EDGE ( 'NONE', *, *, #29720, .T. ) ; +#86818 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#86819 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53300 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40064, #32406, #24776 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86820 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86821 = EDGE_LOOP ( 'NONE', ( #53949, #2188, #75730, #73191 ) ) ; +#86822 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#86823 = ADVANCED_FACE ( 'NONE', ( #2885 ), #41187, .F. ) ; +#86824 = SURFACE_STYLE_FILL_AREA ( #55206 ) ; +#86825 = SURFACE_STYLE_FILL_AREA ( #80698 ) ; +#86826 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#86827 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86828 = CARTESIAN_POINT ( 'NONE', ( 6.028944000000000081, 13.09293800000000019, 0.8991599999999999593 ) ) ; +#86829 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86830 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86831 = CARTESIAN_POINT ( 'NONE', ( -0.5141726715014803828, 1.510031122471161114, 0.8099999999999999423 ) ) ; +#86833 = VERTEX_POINT ( 'NONE', #32523 ) ; +#86832 = VERTEX_POINT ( 'NONE', #48361 ) ; +#86834 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#86835 = FILL_AREA_STYLE ('',( #48034 ) ) ; +#86836 = SURFACE_STYLE_FILL_AREA ( #56729 ) ; +#86837 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#86838 = ORIENTED_EDGE ( 'NONE', *, *, #68926, .F. ) ; +#86839 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86840 = AXIS2_PLACEMENT_3D ( 'NONE', #6212, #23125, #22605 ) ; +#86842 = FILL_AREA_STYLE ('',( #71525 ) ) ; +#86841 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86843 = ORIENTED_EDGE ( 'NONE', *, *, #10262, .F. ) ; +#86844 = ORIENTED_EDGE ( 'NONE', *, *, #57844, .T. ) ; +#86845 = VECTOR ( 'NONE', #71768, 1000.000000000000000 ) ; +#86846 = STYLED_ITEM ( 'NONE', ( #50270 ), #18795 ) ; +#86847 = VECTOR ( 'NONE', #39536, 1000.000000000000000 ) ; +#86848 = FILL_AREA_STYLE ('',( #39875 ) ) ; +#86850 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8648700000000000276 ) ) ; +#86849 = PRESENTATION_STYLE_ASSIGNMENT (( #61867 ) ) ; +#86851 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86852 = ORIENTED_EDGE ( 'NONE', *, *, #60999, .T. ) ; +#86853 = ORIENTED_EDGE ( 'NONE', *, *, #14632, .F. ) ; +#86854 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#86855 = VECTOR ( 'NONE', #93478, 1000.000000000000000 ) ; +#86856 = VERTEX_POINT ( 'NONE', #63672 ) ; +#86857 = ADVANCED_FACE ( 'NONE', ( #94759 ), #1876, .T. ) ; +#86858 = VECTOR ( 'NONE', #5711, 1000.000000000000000 ) ; +#86859 = AXIS2_PLACEMENT_3D ( 'NONE', #70590, #15943, #63955 ) ; +#86860 = CARTESIAN_POINT ( 'NONE', ( 12.04599999999999937, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#86861 = AXIS2_PLACEMENT_3D ( 'NONE', #28295, #35975, #67564 ) ; +#86862 = EDGE_LOOP ( 'NONE', ( #10652, #30251, #26437, #97379 ) ) ; +#86863 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37950 ) ) ; +#86864 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.000000000000000000 ) ) ; +#86865 = SURFACE_STYLE_USAGE ( .BOTH. , #70519 ) ; +#86866 = ORIENTED_EDGE ( 'NONE', *, *, #96949, .T. ) ; +#86867 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#86868 = EDGE_LOOP ( 'NONE', ( #83094, #97473, #12495, #22859 ) ) ; +#86869 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81935 ), #59138 ) ; +#86870 = ADVANCED_FACE ( 'NONE', ( #58545 ), #83495, .T. ) ; +#86871 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#86872 = EDGE_CURVE ( 'NONE', #87203, #29448, #50858, .T. ) ; +#86873 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98162 ), #42856 ) ; +#86874 = EDGE_CURVE ( 'NONE', #24973, #44005, #5332, .T. ) ; +#86875 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#86876 = SURFACE_SIDE_STYLE ('',( #41433 ) ) ; +#86877 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86879 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000019984, 0.1829999999999659954 ) ) ; +#86878 = PRESENTATION_STYLE_ASSIGNMENT (( #56262 ) ) ; +#86880 = CARTESIAN_POINT ( 'NONE', ( 8.227522999999999698, 2.721543000000000934, 0.8648700000000000276 ) ) ; +#86881 = FACE_OUTER_BOUND ( 'NONE', #195, .T. ) ; +#86882 = ORIENTED_EDGE ( 'NONE', *, *, #19499, .F. ) ; +#86883 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15687 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8023, #92367, #69362 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86884 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.000000000000000000 ) ) ; +#86885 = PRESENTATION_STYLE_ASSIGNMENT (( #23094 ) ) ; +#86886 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86888 = ADVANCED_FACE ( 'NONE', ( #90130 ), #20689, .T. ) ; +#86887 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#86889 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86891 = CARTESIAN_POINT ( 'NONE', ( 1.566431021886530051, -1.318798174699070014, 0.8100000000000000533 ) ) ; +#86890 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.000000000000000000 ) ) ; +#86892 = SURFACE_STYLE_USAGE ( .BOTH. , #94522 ) ; +#86893 = PLANE ( 'NONE', #30279 ) ; +#86894 = EDGE_CURVE ( 'NONE', #52330, #16133, #36540, .T. ) ; +#86895 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98250 ) ) ; +#86896 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29799 ) ) ; +#86897 = LINE ( 'NONE', #47064, #67227 ) ; +#86898 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86899 = ORIENTED_EDGE ( 'NONE', *, *, #78231, .F. ) ; +#86900 = VECTOR ( 'NONE', #56342, 1000.000000000000000 ) ; +#86901 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86902 = VERTEX_POINT ( 'NONE', #50384 ) ; +#86903 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, -0.1499999999999999944 ) ) ; +#86904 = EDGE_CURVE ( 'NONE', #93963, #51787, #51862, .T. ) ; +#86906 = FACE_OUTER_BOUND ( 'NONE', #9609, .T. ) ; +#86905 = STYLED_ITEM ( 'NONE', ( #74322 ), #75884 ) ; +#86907 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#86908 = SURFACE_STYLE_FILL_AREA ( #609 ) ; +#86909 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#86910 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86911 = VECTOR ( 'NONE', #74113, 1000.000000000000000 ) ; +#86912 = SURFACE_SIDE_STYLE ('',( #24652 ) ) ; +#86914 = VERTEX_POINT ( 'NONE', #66645 ) ; +#86913 = STYLED_ITEM ( 'NONE', ( #21133 ), #21147 ) ; +#86915 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999942962, -1.979898987322330051, 0.6999285677838846809 ) ) ; +#86916 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#86917 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#86918 = SURFACE_STYLE_USAGE ( .BOTH. , #55779 ) ; +#86919 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31516 ), #29900 ) ; +#86920 = SURFACE_SIDE_STYLE ('',( #55781 ) ) ; +#86921 = STYLED_ITEM ( 'NONE', ( #39933 ), #18912 ) ; +#86922 = LINE ( 'NONE', #54267, #18819 ) ; +#86923 = PRESENTATION_STYLE_ASSIGNMENT (( #63465 ) ) ; +#86924 = CARTESIAN_POINT ( 'NONE', ( 0.005160739295680100321, -0.9302426320460139841, 0.8100000000000000533 ) ) ; +#86926 = STYLED_ITEM ( 'NONE', ( #68928 ), #36626 ) ; +#86925 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86927 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19384, 'distance_accuracy_value', 'NONE'); +#86928 = SURFACE_SIDE_STYLE ('',( #48122 ) ) ; +#86929 = EDGE_CURVE ( 'NONE', #4819, #28196, #97749, .T. ) ; +#86930 = FILL_AREA_STYLE_COLOUR ( '', #71660 ) ; +#86931 = ORIENTED_EDGE ( 'NONE', *, *, #30477, .T. ) ; +#86933 = ORIENTED_EDGE ( 'NONE', *, *, #98716, .T. ) ; +#86932 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#86934 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#86935 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26505, 'distance_accuracy_value', 'NONE'); +#86936 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42537, 'distance_accuracy_value', 'NONE'); +#86937 = VECTOR ( 'NONE', #38053, 1000.000000000000000 ) ; +#86938 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86939 = PRESENTATION_STYLE_ASSIGNMENT (( #8718 ) ) ; +#86940 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#86941 = FACE_OUTER_BOUND ( 'NONE', #1042, .T. ) ; +#86942 = CARTESIAN_POINT ( 'NONE', ( 0.04622384033856599683, -1.137681993439920047, 0.8100000000000000533 ) ) ; +#86943 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86944 = VERTEX_POINT ( 'NONE', #97272 ) ; +#86945 = CARTESIAN_POINT ( 'NONE', ( 1.897517923509739912, -1.370875895369189967, 0.8300000000000011813 ) ) ; +#86946 = ADVANCED_FACE ( 'NONE', ( #30327 ), #84974, .F. ) ; +#86947 = PRESENTATION_STYLE_ASSIGNMENT (( #31287 ) ) ; +#86948 = LINE ( 'NONE', #72126, #22573 ) ; +#86949 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #57495, 'distance_accuracy_value', 'NONE'); +#86950 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#86951 = ORIENTED_EDGE ( 'NONE', *, *, #30810, .T. ) ; +#86952 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86953 = ORIENTED_EDGE ( 'NONE', *, *, #55204, .T. ) ; +#86954 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#86955 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86956 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, 0.000000000000000000 ) ) ; +#86957 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86958 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#86959 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86960 = ORIENTED_EDGE ( 'NONE', *, *, #41699, .F. ) ; +#86961 = FILL_AREA_STYLE ('',( #62993 ) ) ; +#86962 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86963 = MANIFOLD_SOLID_BREP ( 'ÊäÈë48', #7571 ) ; +#86964 = VERTEX_POINT ( 'NONE', #77826 ) ; +#86965 = FACE_OUTER_BOUND ( 'NONE', #30646, .T. ) ; +#86966 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#86967 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#86968 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#86969 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#86970 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#86971 = EDGE_LOOP ( 'NONE', ( #90462, #51683, #3458, #26487 ) ) ; +#86973 = VERTEX_POINT ( 'NONE', #7789 ) ; +#86972 = VERTEX_POINT ( 'NONE', #45143 ) ; +#86974 = SURFACE_STYLE_FILL_AREA ( #71657 ) ; +#86975 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95094 ) ) ; +#86976 = STYLED_ITEM ( 'NONE', ( #93044 ), #26011 ) ; +#86977 = ORIENTED_EDGE ( 'NONE', *, *, #72809, .F. ) ; +#86978 = EDGE_CURVE ( 'NONE', #100232, #31005, #47186, .T. ) ; +#86979 = CARTESIAN_POINT ( 'NONE', ( -0.6166666666666659191, 3.099999999999989875, 0.000000000000000000 ) ) ; +#86980 = VECTOR ( 'NONE', #76690, 1000.000000000000000 ) ; +#86981 = ORIENTED_EDGE ( 'NONE', *, *, #59691, .F. ) ; +#86982 = ORIENTED_EDGE ( 'NONE', *, *, #60169, .T. ) ; +#86983 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#86984 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70640 ), #52726 ) ; +#86985 = LINE ( 'NONE', #72662, #16123 ) ; +#86986 = ORIENTED_EDGE ( 'NONE', *, *, #49075, .F. ) ; +#86987 = CARTESIAN_POINT ( 'NONE', ( 9.818512999999999380, 3.393295000000000172, 0.8648700000000000276 ) ) ; +#86988 = VECTOR ( 'NONE', #85009, 1000.000000000000000 ) ; +#86989 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#86990 = ORIENTED_EDGE ( 'NONE', *, *, #58986, .T. ) ; +#86991 = LINE ( 'NONE', #89005, #95377 ) ; +#86992 = EDGE_CURVE ( 'NONE', #25637, #89231, #70157, .T. ) ; +#86993 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36947 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94710, #793, #64607 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#86994 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#86995 = STYLED_ITEM ( 'NONE', ( #83016 ), #35310 ) ; +#86996 = EDGE_LOOP ( 'NONE', ( #11756, #23048, #70272, #78637 ) ) ; +#86997 = SURFACE_STYLE_FILL_AREA ( #85974 ) ; +#86998 = ORIENTED_EDGE ( 'NONE', *, *, #60123, .F. ) ; +#86999 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#87000 = FILL_AREA_STYLE ('',( #55864 ) ) ; +#87001 = STYLED_ITEM ( 'NONE', ( #77637 ), #96770 ) ; +#87003 = FILL_AREA_STYLE_COLOUR ( '', #36772 ) ; +#87002 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87004 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8648700000000000276 ) ) ; +#87005 = FACE_OUTER_BOUND ( 'NONE', #83628, .T. ) ; +#87006 = AXIS2_PLACEMENT_3D ( 'NONE', #52975, #13563, #76419 ) ; +#87007 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87008 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39696 ) ) ; +#87009 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87010 = ORIENTED_EDGE ( 'NONE', *, *, #28237, .T. ) ; +#87011 = SURFACE_SIDE_STYLE ('',( #88008 ) ) ; +#87012 = LINE ( 'NONE', #64028, #96704 ) ; +#87013 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87014 = CARTESIAN_POINT ( 'NONE', ( 1.854034869405480013, -1.451435312150680224, 0.8300000000000011813 ) ) ; +#87015 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79280, 'distance_accuracy_value', 'NONE'); +#87016 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87017 = CARTESIAN_POINT ( 'NONE', ( -1.147844963924800066, -0.8845642871695170717, 0.8100000000000000533 ) ) ; +#87018 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#87019 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87020 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#87021 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87022 = LINE ( 'NONE', #72198, #86847 ) ; +#87023 = EDGE_LOOP ( 'NONE', ( #77383, #68715, #51730, #89941 ) ) ; +#87024 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#87025 = EDGE_CURVE ( 'NONE', #6650, #98440, #20526, .T. ) ; +#87026 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #29927 ) ) ; +#87029 = FILL_AREA_STYLE_COLOUR ( '', #45975 ) ; +#87028 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87027 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87030 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, -1.050000000000000044 ) ) ; +#87031 = SURFACE_SIDE_STYLE ('',( #71191 ) ) ; +#87032 = SURFACE_STYLE_USAGE ( .BOTH. , #24261 ) ; +#87033 = CARTESIAN_POINT ( 'NONE', ( 1.296623048369099918, -0.9836087549443109923, 0.8100000000000000533 ) ) ; +#87034 = ORIENTED_EDGE ( 'NONE', *, *, #7042, .T. ) ; +#87035 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87036 = PRESENTATION_STYLE_ASSIGNMENT (( #94147 ) ) ; +#87037 = FILL_AREA_STYLE_COLOUR ( '', #12166 ) ; +#87038 = PLANE ( 'NONE', #11736 ) ; +#87039 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87040 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, -3.099999999999989875, 0.000000000000000000 ) ) ; +#87041 = LINE ( 'NONE', #49250, #35521 ) ; +#87042 = VECTOR ( 'NONE', #36852, 1000.000000000000000 ) ; +#87043 = PLANE ( 'NONE', #5520 ) ; +#87044 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#87045 = FILL_AREA_STYLE ('',( #79391 ) ) ; +#87046 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87047 = SURFACE_STYLE_USAGE ( .BOTH. , #55923 ) ; +#87048 = PLANE ( 'NONE', #77959 ) ; +#87049 = ADVANCED_FACE ( 'NONE', ( #93602 ), #35174, .F. ) ; +#87050 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.1493506493506490118 ) ) ; +#87051 = ORIENTED_EDGE ( 'NONE', *, *, #63448, .F. ) ; +#87052 = PRESENTATION_STYLE_ASSIGNMENT (( #26792 ) ) ; +#87053 = ORIENTED_EDGE ( 'NONE', *, *, #42284, .T. ) ; +#87054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65441, 'distance_accuracy_value', 'NONE'); +#87055 = FILL_AREA_STYLE ('',( #24801 ) ) ; +#87056 = PLANE ( 'NONE', #69004 ) ; +#87057 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88768 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58691, #19853, #35205 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87058 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87059 = SURFACE_SIDE_STYLE ('',( #31411 ) ) ; +#87060 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87061 = CARTESIAN_POINT ( 'NONE', ( -0.9467570119888509828, -1.236164603532529993, 0.8299999999999999600 ) ) ; +#87062 = ORIENTED_EDGE ( 'NONE', *, *, #44330, .T. ) ; +#87063 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87064 = ADVANCED_FACE ( 'NONE', ( #10306 ), #8799, .F. ) ; +#87065 = FILL_AREA_STYLE ('',( #24811 ) ) ; +#87066 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6880, 'distance_accuracy_value', 'NONE'); +#87068 = VECTOR ( 'NONE', #99706, 1000.000000000000000 ) ; +#87067 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47104 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41518, #3208, #51192 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87069 = STYLED_ITEM ( 'NONE', ( #24007 ), #19107 ) ; +#87070 = SURFACE_STYLE_USAGE ( .BOTH. , #1289 ) ; +#87071 = VERTEX_POINT ( 'NONE', #74204 ) ; +#87072 = PLANE ( 'NONE', #14874 ) ; +#87073 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87074 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87075 = VECTOR ( 'NONE', #58985, 1000.000000000000000 ) ; +#87076 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87077 = EDGE_CURVE ( 'NONE', #12898, #56699, #67036, .T. ) ; +#87078 = VERTEX_POINT ( 'NONE', #51234 ) ; +#87079 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#87080 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 1.723820061220085131, -0.02000000000000000042 ) ) ; +#87081 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22017, 'distance_accuracy_value', 'NONE'); +#87082 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87083 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26746 ) ) ; +#87084 = FILL_AREA_STYLE ('',( #25322 ) ) ; +#87085 = EDGE_CURVE ( 'NONE', #60233, #96693, #88711, .T. ) ; +#87086 = VERTEX_POINT ( 'NONE', #4254 ) ; +#87087 = SURFACE_STYLE_FILL_AREA ( #55966 ) ; +#87088 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#87089 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87090 = VERTEX_POINT ( 'NONE', #19571 ) ; +#87091 = LINE ( 'NONE', #55970, #78730 ) ; +#87092 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #70481, #8114, #63378, #77143 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87093 = PRESENTATION_STYLE_ASSIGNMENT (( #40637 ) ) ; +#87094 = ADVANCED_FACE ( 'NONE', ( #81395 ), #27260, .F. ) ; +#87095 = EDGE_CURVE ( 'NONE', #40780, #29579, #90012, .T. ) ; +#87096 = VECTOR ( 'NONE', #22446, 1000.000000000000000 ) ; +#87097 = EDGE_CURVE ( 'NONE', #68435, #17076, #50944, .T. ) ; +#87098 = VERTEX_POINT ( 'NONE', #91024 ) ; +#87099 = EDGE_CURVE ( 'NONE', #33366, #86832, #73214, .T. ) ; +#87100 = ORIENTED_EDGE ( 'NONE', *, *, #27676, .T. ) ; +#87101 = FILL_AREA_STYLE ('',( #56992 ) ) ; +#87103 = SURFACE_SIDE_STYLE ('',( #62630 ) ) ; +#87102 = SURFACE_STYLE_FILL_AREA ( #2844 ) ; +#87104 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3927 ), #98449 ) ; +#87105 = ORIENTED_EDGE ( 'NONE', *, *, #62389, .F. ) ; +#87106 = CARTESIAN_POINT ( 'NONE', ( -0.5999999999999999778, 0.2500000000000000555, 0.6500000000000001332 ) ) ; +#87107 = EDGE_CURVE ( 'NONE', #58394, #38857, #89535, .T. ) ; +#87108 = AXIS2_PLACEMENT_3D ( 'NONE', #38669, #76460, #46813 ) ; +#87109 = ORIENTED_EDGE ( 'NONE', *, *, #72973, .F. ) ; +#87111 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#87110 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#87112 = VERTEX_POINT ( 'NONE', #80882 ) ; +#87113 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33543 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99884, #36238, #22393 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87114 = ORIENTED_EDGE ( 'NONE', *, *, #49319, .F. ) ; +#87115 = EDGE_CURVE ( 'NONE', #50063, #13386, #75217, .T. ) ; +#87117 = FILL_AREA_STYLE ('',( #55995 ) ) ; +#87116 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87118 = SURFACE_SIDE_STYLE ('',( #40663 ) ) ; +#87119 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62803 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71363, #72361, #33075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87120 = VERTEX_POINT ( 'NONE', #36415 ) ; +#87121 = LINE ( 'NONE', #71806, #97209 ) ; +#87122 = VECTOR ( 'NONE', #29127, 1000.000000000000000 ) ; +#87123 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 12.49601200000000034, 0.8648700000000000276 ) ) ; +#87124 = VERTEX_POINT ( 'NONE', #89026 ) ; +#87125 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87126 = ORIENTED_EDGE ( 'NONE', *, *, #55555, .F. ) ; +#87127 = ORIENTED_EDGE ( 'NONE', *, *, #92418, .T. ) ; +#87128 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87129 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31724 ), #61049 ) ; +#87131 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87130 = PRESENTATION_STYLE_ASSIGNMENT (( #24878 ) ) ; +#87132 = FILL_AREA_STYLE ('',( #40679 ) ) ; +#87133 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #89374 ) ; +#87134 = SURFACE_STYLE_FILL_AREA ( #62659 ) ; +#87135 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#87137 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21887 ) ) ; +#87136 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85435 ) ) ; +#87138 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34981 ) ) ; +#87139 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87140 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87141 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30038 ), #2384 ) ; +#87142 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#87143 = ORIENTED_EDGE ( 'NONE', *, *, #17123, .F. ) ; +#87144 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8648700000000000276 ) ) ; +#87145 = EDGE_CURVE ( 'NONE', #93936, #66499, #67515, .T. ) ; +#87146 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87147 = STYLED_ITEM ( 'NONE', ( #70249 ), #3383 ) ; +#87148 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 6.999539000000000399, 0.8648700000000000276 ) ) ; +#87149 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82278 ) ) ; +#87150 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.53504399999999919, 0.8648700000000000276 ) ) ; +#87151 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#87152 = ADVANCED_FACE ( 'NONE', ( #68012 ), #6191, .F. ) ; +#87153 = LINE ( 'NONE', #17175, #81015 ) ; +#87154 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#87155 = EDGE_LOOP ( 'NONE', ( #64099, #27636, #54076, #51980 ) ) ; +#87156 = FILL_AREA_STYLE ('',( #87654 ) ) ; +#87157 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87158 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87159 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86927 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19384, #90847, #52062 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87160 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#87161 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71135, 'distance_accuracy_value', 'NONE'); +#87162 = CARTESIAN_POINT ( 'NONE', ( -1.166666666666666741, 3.500000000000000000, 0.000000000000000000 ) ) ; +#87163 = SURFACE_SIDE_STYLE ('',( #25902 ) ) ; +#87164 = LINE ( 'NONE', #63703, #84973 ) ; +#87165 = LINE ( 'NONE', #63705, #78371 ) ; +#87166 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87167 = FILL_AREA_STYLE_COLOUR ( '', #38973 ) ; +#87168 = STYLED_ITEM ( 'NONE', ( #12082 ), #71375 ) ; +#87169 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8648700000000000276 ) ) ; +#87170 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87171 = CARTESIAN_POINT ( 'NONE', ( 1.797750835596120034, -1.188470249711290005, 0.8100000000000004974 ) ) ; +#87172 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88529, #26264, #49752, #79364 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87173 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76022, 'distance_accuracy_value', 'NONE'); +#87174 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#87175 = EDGE_LOOP ( 'NONE', ( #40382, #2702, #40549, #72112 ) ) ; +#87176 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.300000000000000711, 0.000000000000000000 ) ) ; +#87177 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.000000000000000000 ) ) ; +#87178 = STYLED_ITEM ( 'NONE', ( #86849 ), #82283 ) ; +#87180 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87179 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30084 ) ) ; +#87181 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78430, 'distance_accuracy_value', 'NONE'); +#87183 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 8.750000000000000000, 0.000000000000000000 ) ) ; +#87182 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87184 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.900000000000000577, 0.000000000000000000 ) ) ; +#87185 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44798 ), #80721 ) ; +#87186 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61105 ), #96921 ) ; +#87187 = PLANE ( 'NONE', #72218 ) ; +#87188 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87189 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87190 = ORIENTED_EDGE ( 'NONE', *, *, #51102, .F. ) ; +#87191 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87192 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87193 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14471, 'distance_accuracy_value', 'NONE'); +#87194 = PLANE ( 'NONE', #38064 ) ; +#87195 = VECTOR ( 'NONE', #62286, 1000.000000000000000 ) ; +#87196 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18567, 'distance_accuracy_value', 'NONE'); +#87197 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #5682, #12288 ) ; +#87198 = AXIS2_PLACEMENT_3D ( 'NONE', #76607, #82776, #99495 ) ; +#87199 = ORIENTED_EDGE ( 'NONE', *, *, #98659, .T. ) ; +#87200 = ORIENTED_EDGE ( 'NONE', *, *, #46241, .F. ) ; +#87201 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79044 ), #39899 ) ; +#87202 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#87203 = VERTEX_POINT ( 'NONE', #100075 ) ; +#87204 = CARTESIAN_POINT ( 'NONE', ( 0.2744150338662970090, -0.9994076953096140414, 0.8299999999999996270 ) ) ; +#87205 = SURFACE_SIDE_STYLE ('',( #56076 ) ) ; +#87206 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.149999999999970157, 0.000000000000000000 ) ) ; +#87207 = FACE_OUTER_BOUND ( 'NONE', #78612, .T. ) ; +#87208 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#87209 = PRODUCT_CONTEXT ( 'NONE', #26718, 'mechanical' ) ; +#87210 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87212 = ORIENTED_EDGE ( 'NONE', *, *, #87492, .F. ) ; +#87211 = ORIENTED_EDGE ( 'NONE', *, *, #75276, .F. ) ; +#87213 = EDGE_LOOP ( 'NONE', ( #32063, #75777, #31386, #44386 ) ) ; +#87214 = EDGE_CURVE ( 'NONE', #20186, #38666, #54244, .T. ) ; +#87215 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#87216 = PLANE ( 'NONE', #20290 ) ; +#87217 = ORIENTED_EDGE ( 'NONE', *, *, #82108, .F. ) ; +#87218 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#87219 = AXIS2_PLACEMENT_3D ( 'NONE', #42141, #56980, #3820 ) ; +#87220 = VERTEX_POINT ( 'NONE', #84369 ) ; +#87221 = VERTEX_POINT ( 'NONE', #99589 ) ; +#87222 = EDGE_LOOP ( 'NONE', ( #46760, #69945, #6154, #19297 ) ) ; +#87223 = ORIENTED_EDGE ( 'NONE', *, *, #69319, .T. ) ; +#87224 = EDGE_CURVE ( 'NONE', #34477, #61753, #62416, .T. ) ; +#87225 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87226 = AXIS2_PLACEMENT_3D ( 'NONE', #22684, #23194, #53824 ) ; +#87227 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12084 ) ) ; +#87229 = ORIENTED_EDGE ( 'NONE', *, *, #6912, .T. ) ; +#87228 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 10.10116700000000201, 0.8991599999999999593 ) ) ; +#87230 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#87231 = STYLED_ITEM ( 'NONE', ( #43580 ), #89653 ) ; +#87232 = ORIENTED_EDGE ( 'NONE', *, *, #24298, .T. ) ; +#87234 = CARTESIAN_POINT ( 'NONE', ( 0.6431619866146579545, 0.5992840759269659756, 0.8100000000000000533 ) ) ; +#87233 = LINE ( 'NONE', #3502, #72657 ) ; +#87235 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#87236 = ORIENTED_EDGE ( 'NONE', *, *, #95714, .T. ) ; +#87237 = VERTEX_POINT ( 'NONE', #46018 ) ; +#87238 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999940048, -2.700000000000000178, -0.02000000000005449849 ) ) ; +#87239 = CARTESIAN_POINT ( 'NONE', ( 1.800644492816920295, -1.399205570841099977, 0.8300000000000002931 ) ) ; +#87240 = FILL_AREA_STYLE ('',( #54627 ) ) ; +#87241 = AXIS2_PLACEMENT_3D ( 'NONE', #47673, #71158, #24739 ) ; +#87242 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62051 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36390, #99566, #21067 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87243 = SURFACE_STYLE_USAGE ( .BOTH. , #86751 ) ; +#87244 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#87245 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.300000000000000044, 0.000000000000000000 ) ) ; +#87246 = EDGE_CURVE ( 'NONE', #1165, #64088, #54753, .T. ) ; +#87247 = SURFACE_STYLE_FILL_AREA ( #71945 ) ; +#87248 = ORIENTED_EDGE ( 'NONE', *, *, #74287, .F. ) ; +#87249 = CARTESIAN_POINT ( 'NONE', ( 0.3953060575754059891, -1.200834233358659908, 0.8100000000000000533 ) ) ; +#87250 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87251 = CYLINDRICAL_SURFACE ( 'NONE', #59439, 0.1000000000000000056 ) ; +#87252 = ORIENTED_EDGE ( 'NONE', *, *, #53099, .F. ) ; +#87253 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.149999999999999911, -0.02000000000000000042 ) ) ; +#87254 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#87255 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87256 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8648700000000000276 ) ) ; +#87257 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87258 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 1.900000000000000133, 0.000000000000000000 ) ) ; +#87259 = VECTOR ( 'NONE', #32057, 1000.000000000000000 ) ; +#87260 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#87261 = ADVANCED_FACE ( 'NONE', ( #7174 ), #23102, .T. ) ; +#87262 = FILL_AREA_STYLE_COLOUR ( '', #22157 ) ; +#87263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56340 ) ) ; +#87264 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 4.524664999999999715, 0.8648700000000000276 ) ) ; +#87265 = PRESENTATION_STYLE_ASSIGNMENT (( #17808 ) ) ; +#87266 = STYLED_ITEM ( 'NONE', ( #61058 ), #98674 ) ; +#87267 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87268 = CARTESIAN_POINT ( 'NONE', ( -1.231483759408549927, -0.9661431204389000493, 0.8299999999999998490 ) ) ; +#87269 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#87270 = FILL_AREA_STYLE ('',( #7558 ) ) ; +#87271 = VECTOR ( 'NONE', #68146, 1000.000000000000000 ) ; +#87272 = SURFACE_SIDE_STYLE ('',( #39812 ) ) ; +#87273 = FACE_OUTER_BOUND ( 'NONE', #10185, .T. ) ; +#87274 = LINE ( 'NONE', #93874, #48688 ) ; +#87275 = SURFACE_SIDE_STYLE ('',( #9587 ) ) ; +#87276 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87277 = SURFACE_STYLE_FILL_AREA ( #16288 ) ; +#87278 = STYLED_ITEM ( 'NONE', ( #17659 ), #12559 ) ; +#87279 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22769, 'distance_accuracy_value', 'NONE'); +#87280 = EDGE_LOOP ( 'NONE', ( #74928, #32102, #44958, #15344, #100013, #62991 ) ) ; +#87281 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87282 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#87283 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #9335 ) ; +#87284 = VERTEX_POINT ( 'NONE', #39924 ) ; +#87285 = PLANE ( 'NONE', #35560 ) ; +#87286 = EDGE_CURVE ( 'NONE', #5073, #3583, #86897, .T. ) ; +#87287 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#87288 = CARTESIAN_POINT ( 'NONE', ( 1.783955832751769943, -0.9153515042605530061, 0.8299999999999999600 ) ) ; +#87289 = SURFACE_SIDE_STYLE ('',( #46441 ) ) ; +#87290 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#87291 = VECTOR ( 'NONE', #25218, 1000.000000000000000 ) ; +#87292 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87293 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #94611, #23183, #14461, #78803 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87294 = STYLED_ITEM ( 'NONE', ( #13578 ), #73206 ) ; +#87295 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#87296 = ADVANCED_FACE ( 'NONE', ( #86385 ), #48094, .T. ) ; +#87297 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87298 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#87299 = ORIENTED_EDGE ( 'NONE', *, *, #44061, .T. ) ; +#87300 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87301 = VERTEX_POINT ( 'NONE', #31754 ) ; +#87302 = PLANE ( 'NONE', #95041 ) ; +#87303 = CARTESIAN_POINT ( 'NONE', ( 5.413238000000000660, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#87305 = PLANE ( 'NONE', #55945 ) ; +#87304 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15550 ) ) ; +#87306 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87307 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87308 = ORIENTED_EDGE ( 'NONE', *, *, #91739, .T. ) ; +#87309 = EDGE_CURVE ( 'NONE', #87865, #95525, #48617, .T. ) ; +#87310 = CARTESIAN_POINT ( 'NONE', ( 1.070765459575029999, -1.007957212727089935, 0.8300000000000002931 ) ) ; +#87311 = EDGE_CURVE ( 'NONE', #24841, #77162, #86368, .T. ) ; +#87312 = LINE ( 'NONE', #65332, #5349 ) ; +#87313 = EDGE_LOOP ( 'NONE', ( #28736, #7888, #5398, #30408 ) ) ; +#87314 = SURFACE_STYLE_USAGE ( .BOTH. , #66227 ) ; +#87315 = LINE ( 'NONE', #46471, #35418 ) ; +#87316 = EDGE_LOOP ( 'NONE', ( #24428, #45462, #36049, #83218 ) ) ; +#87317 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64520 ), #33561 ) ; +#87318 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100108 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #95196, #40120, #63106 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87319 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8100000000000000533 ) ) ; +#87320 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87321 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#87322 = VECTOR ( 'NONE', #27594, 1000.000000000000000 ) ; +#87323 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#87326 = EDGE_LOOP ( 'NONE', ( #39632, #36128, #58230, #34783 ) ) ; +#87325 = VERTEX_POINT ( 'NONE', #17424 ) ; +#87324 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #76809, #15499, #77816, #7777, #91618, #21688, #37530, #39026, #70146, #23711, #209, #60524, #83981, #13976, #68633, #84471, #29838 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.597396692721303115E-05, 5.032973895643998928E-05, 7.289812049175703988E-05, 9.396061160246955773E-05, 0.0001139761260554269959, 0.0001333073934880849053, 0.0001519570402952260678, 0.0001702491890266488283, 0.0001883899223430415305, 0.0002062252293718392965, 0.0002241715564723738556, 0.0002419546764509979261, 0.0002779640821590013467, 0.0003141735854813355617 ), + .UNSPECIFIED. ) ; +#87327 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#87328 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#87329 = ORIENTED_EDGE ( 'NONE', *, *, #40803, .T. ) ; +#87330 = ADVANCED_FACE ( 'NONE', ( #80762 ), #12217, .T. ) ; +#87331 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#87332 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98605 ), #82466 ) ; +#87333 = VECTOR ( 'NONE', #28664, 1000.000000000000000 ) ; +#87335 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87334 = SURFACE_SIDE_STYLE ('',( #56223 ) ) ; +#87336 = ORIENTED_EDGE ( 'NONE', *, *, #28014, .F. ) ; +#87337 = ORIENTED_EDGE ( 'NONE', *, *, #66447, .F. ) ; +#87339 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71018 ), #15505 ) ; +#87338 = PRESENTATION_STYLE_ASSIGNMENT (( #72515 ) ) ; +#87340 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#87341 = VECTOR ( 'NONE', #7198, 1000.000000000000000 ) ; +#87342 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#87343 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87344 = VERTEX_POINT ( 'NONE', #73588 ) ; +#87345 = ORIENTED_EDGE ( 'NONE', *, *, #29277, .T. ) ; +#87346 = STYLED_ITEM ( 'NONE', ( #23584 ), #4608 ) ; +#87347 = ORIENTED_EDGE ( 'NONE', *, *, #72353, .F. ) ; +#87348 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#87349 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87350 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87351 = VERTEX_POINT ( 'NONE', #97995 ) ; +#87352 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100675, #94115, #77312, #16515 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87353 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87354 = LINE ( 'NONE', #2110, #44885 ) ; +#87355 = CARTESIAN_POINT ( 'NONE', ( 1.885232907775660216, -1.407232784796780045, 0.8099999999999996092 ) ) ; +#87356 = ORIENTED_EDGE ( 'NONE', *, *, #82598, .F. ) ; +#87357 = FILL_AREA_STYLE ('',( #8647 ) ) ; +#87358 = SURFACE_SIDE_STYLE ('',( #73560 ) ) ; +#87359 = ORIENTED_EDGE ( 'NONE', *, *, #48458, .T. ) ; +#87360 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.100000000000000089 ) ) ; +#87361 = PLANE ( 'NONE', #30155 ) ; +#87362 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #73243, #72216, #42588, #65062 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87363 = SURFACE_SIDE_STYLE ('',( #40422 ) ) ; +#87364 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #23247, #53874, #36567, #44675 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87365 = LINE ( 'NONE', #79734, #33540 ) ; +#87366 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#87367 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87368 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#87369 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#87370 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80919 ), #46610 ) ; +#87372 = PLANE ( 'NONE', #78922 ) ; +#87371 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #82576 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#87373 = ORIENTED_EDGE ( 'NONE', *, *, #46194, .F. ) ; +#87374 = PLANE ( 'NONE', #56672 ) ; +#87375 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87376 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#87377 = STYLED_ITEM ( 'NONE', ( #96757 ), #83618 ) ; +#87378 = CIRCLE ( 'NONE', #7407, 0.6999999999999999556 ) ; +#87379 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87380 = SURFACE_SIDE_STYLE ('',( #11198 ) ) ; +#87381 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.1600000000000000033, 1.129999999999999893 ) ) ; +#87382 = EDGE_CURVE ( 'NONE', #85080, #2585, #26518, .T. ) ; +#87384 = VECTOR ( 'NONE', #86463, 1000.000000000000000 ) ; +#87383 = LINE ( 'NONE', #71580, #93889 ) ; +#87385 = VECTOR ( 'NONE', #49111, 1000.000000000000000 ) ; +#87386 = STYLED_ITEM ( 'NONE', ( #71792 ), #82767 ) ; +#87387 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87388 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87389 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87390 = VECTOR ( 'NONE', #87230, 1000.000000000000000 ) ; +#87391 = STYLED_ITEM ( 'NONE', ( #91340 ), #48969 ) ; +#87392 = PLANE ( 'NONE', #22141 ) ; +#87393 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87394 = ORIENTED_EDGE ( 'NONE', *, *, #17844, .T. ) ; +#87395 = SURFACE_STYLE_FILL_AREA ( #63446 ) ; +#87397 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87396 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#87398 = FILL_AREA_STYLE ('',( #66432 ) ) ; +#87399 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95531 ), #51585 ) ; +#87400 = DIRECTION ( 'NONE', ( -0.7071060119555133694, -0.7071075504167448900, 0.000000000000000000 ) ) ; +#87401 = FILL_AREA_STYLE_COLOUR ( '', #61065 ) ; +#87402 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87403 = DIRECTION ( 'NONE', ( -0.7071060119555143686, -0.7071075504167438908, 0.000000000000000000 ) ) ; +#87404 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70185, 'distance_accuracy_value', 'NONE'); +#87405 = EDGE_LOOP ( 'NONE', ( #89537, #56030, #64970, #74073 ) ) ; +#87406 = FILL_AREA_STYLE ('',( #8197 ) ) ; +#87407 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87409 = AXIS2_PLACEMENT_3D ( 'NONE', #60637, #50975, #97855 ) ; +#87408 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87410 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13963 ), #23800 ) ; +#87411 = SURFACE_SIDE_STYLE ('',( #47090 ) ) ; +#87412 = LINE ( 'NONE', #42956, #1315 ) ; +#87413 = CARTESIAN_POINT ( 'NONE', ( 1.476179938779914602, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#87414 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#87415 = ADVANCED_FACE ( 'NONE', ( #12730 ), #28137, .T. ) ; +#87416 = EDGE_CURVE ( 'NONE', #63639, #49623, #26637, .T. ) ; +#87417 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#87418 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87419 = VERTEX_POINT ( 'NONE', #57807 ) ; +#87420 = EDGE_LOOP ( 'NONE', ( #25972, #83687, #25852, #54779, #79359, #42846 ) ) ; +#87421 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87655 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38142, #92230, #37642 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87422 = PLANE ( 'NONE', #9431 ) ; +#87423 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21809, 'distance_accuracy_value', 'NONE'); +#87424 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87425 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87426 = FILL_AREA_STYLE ('',( #56328 ) ) ; +#87427 = STYLED_ITEM ( 'NONE', ( #42263 ), #12901 ) ; +#87428 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#87429 = CARTESIAN_POINT ( 'NONE', ( 0.04624266161326810037, -1.451435312150680224, 0.8300000000000004041 ) ) ; +#87430 = CARTESIAN_POINT ( 'NONE', ( 0.9400000000000000577, 0.1200000000000003147, 0.3000000000000000444 ) ) ; +#87431 = PLANE ( 'NONE', #13440 ) ; +#87432 = VERTEX_POINT ( 'NONE', #81279 ) ; +#87433 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87434 = EDGE_CURVE ( 'NONE', #60367, #64495, #36304, .T. ) ; +#87435 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87436 = EDGE_CURVE ( 'NONE', #86756, #20920, #77313, .T. ) ; +#87437 = ORIENTED_EDGE ( 'NONE', *, *, #88742, .T. ) ; +#87438 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8099999999999112354 ) ) ; +#87439 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#87440 = LINE ( 'NONE', #15571, #93991 ) ; +#87441 = EDGE_LOOP ( 'NONE', ( #281, #48174, #1177, #16832 ) ) ; +#87442 = EDGE_CURVE ( 'NONE', #92147, #46638, #46427, .T. ) ; +#87443 = STYLED_ITEM ( 'NONE', ( #62918 ), #73625 ) ; +#87444 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87445 = SURFACE_SIDE_STYLE ('',( #56350 ) ) ; +#87446 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.000000000000000000 ) ) ; +#87447 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 4.680228999999999751, 0.8648700000000000276 ) ) ; +#87448 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#87449 = ORIENTED_EDGE ( 'NONE', *, *, #54066, .T. ) ; +#87450 = FACE_OUTER_BOUND ( 'NONE', #97474, .T. ) ; +#87451 = ORIENTED_EDGE ( 'NONE', *, *, #37195, .F. ) ; +#87452 = ADVANCED_FACE ( 'NONE', ( #68414 ), #13224, .T. ) ; +#87453 = FILL_AREA_STYLE_COLOUR ( '', #62284 ) ; +#87454 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65731 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80523, #47342, #41717 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87455 = FACE_OUTER_BOUND ( 'NONE', #35772, .T. ) ; +#87456 = MANIFOLD_SOLID_BREP ( 'ÊäÈë31', #89163 ) ; +#87457 = VECTOR ( 'NONE', #64300, 1000.000000000000000 ) ; +#87458 = ORIENTED_EDGE ( 'NONE', *, *, #71541, .T. ) ; +#87459 = EDGE_CURVE ( 'NONE', #8603, #95470, #60305, .T. ) ; +#87460 = SURFACE_STYLE_USAGE ( .BOTH. , #73650 ) ; +#87461 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#87462 = CARTESIAN_POINT ( 'NONE', ( 1.769936080281629964, -0.9872600217210630857, 0.8300000000000004041 ) ) ; +#87463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87464 = PRESENTATION_STYLE_ASSIGNMENT (( #56857 ) ) ; +#87465 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87466 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#87467 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27808 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2451, #18223, #41268 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87468 = VERTEX_POINT ( 'NONE', #52629 ) ; +#87470 = VERTEX_POINT ( 'NONE', #91411 ) ; +#87469 = ORIENTED_EDGE ( 'NONE', *, *, #87311, .T. ) ; +#87471 = PLANE ( 'NONE', #59743 ) ; +#87472 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100930 ) ; +#87473 = ORIENTED_EDGE ( 'NONE', *, *, #45120, .T. ) ; +#87474 = EDGE_CURVE ( 'NONE', #52068, #52193, #30111, .T. ) ; +#87475 = VECTOR ( 'NONE', #89287, 1000.000000000000000 ) ; +#87476 = EDGE_LOOP ( 'NONE', ( #9024, #922, #89119, #77763 ) ) ; +#87478 = ORIENTED_EDGE ( 'NONE', *, *, #31160, .T. ) ; +#87477 = LINE ( 'NONE', #17506, #29697 ) ; +#87479 = EDGE_CURVE ( 'NONE', #73267, #12657, #54118, .T. ) ; +#87480 = SURFACE_STYLE_USAGE ( .BOTH. , #1732 ) ; +#87481 = ORIENTED_EDGE ( 'NONE', *, *, #77474, .F. ) ; +#87482 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#87483 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#87484 = VERTEX_POINT ( 'NONE', #44909 ) ; +#87485 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #76779 ) ) ; +#87486 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87487 = ORIENTED_EDGE ( 'NONE', *, *, #13355, .T. ) ; +#87488 = FACE_OUTER_BOUND ( 'NONE', #49303, .T. ) ; +#87489 = ORIENTED_EDGE ( 'NONE', *, *, #96811, .F. ) ; +#87490 = VECTOR ( 'NONE', #12508, 1000.000000000000000 ) ; +#87491 = VECTOR ( 'NONE', #34516, 1000.000000000000000 ) ; +#87492 = EDGE_CURVE ( 'NONE', #15440, #31163, #76088, .T. ) ; +#87493 = AXIS2_PLACEMENT_3D ( 'NONE', #42669, #58528, #72287 ) ; +#87494 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#87495 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87496 = PRESENTATION_STYLE_ASSIGNMENT (( #2250 ) ) ; +#87498 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87497 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87499 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87500 = EDGE_CURVE ( 'NONE', #91118, #24848, #38309, .T. ) ; +#87501 = SURFACE_STYLE_FILL_AREA ( #96140 ) ; +#87502 = CARTESIAN_POINT ( 'NONE', ( -1.015539310577060039, -0.9199924700473179895, 0.8299999999999999600 ) ) ; +#87504 = ADVANCED_FACE ( 'NONE', ( #15266 ), #7556, .T. ) ; +#87503 = CARTESIAN_POINT ( 'NONE', ( 0.9913778824254210198, -0.9987792914302020542, 0.8100000000000000533 ) ) ; +#87505 = AXIS2_PLACEMENT_3D ( 'NONE', #46805, #72310, #16152 ) ; +#87506 = ORIENTED_EDGE ( 'NONE', *, *, #80205, .F. ) ; +#87507 = FACE_BOUND ( 'NONE', #37399, .T. ) ; +#87508 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#87509 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87510 = FILL_AREA_STYLE_COLOUR ( '', #8466 ) ; +#87511 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87512 = EDGE_LOOP ( 'NONE', ( #44895, #100610, #15566, #84526 ) ) ; +#87513 = LINE ( 'NONE', #9823, #75679 ) ; +#87515 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82642 ), #32136 ) ; +#87514 = LINE ( 'NONE', #71186, #23459 ) ; +#87516 = ADVANCED_FACE ( 'NONE', ( #93867 ), #71962, .T. ) ; +#87519 = FACE_OUTER_BOUND ( 'NONE', #83986, .T. ) ; +#87518 = SURFACE_SIDE_STYLE ('',( #94131 ) ) ; +#87517 = PRESENTATION_STYLE_ASSIGNMENT (( #56914 ) ) ; +#87520 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.48243800000000192, 0.8648700000000000276 ) ) ; +#87521 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71192, 'distance_accuracy_value', 'NONE'); +#87522 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207790140, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#87523 = AXIS2_PLACEMENT_3D ( 'NONE', #66194, #12478, #82034 ) ; +#87524 = CARTESIAN_POINT ( 'NONE', ( -0.1833333333333323212, 3.099999999999980549, 0.000000000000000000 ) ) ; +#87525 = PRESENTATION_STYLE_ASSIGNMENT (( #80903 ) ) ; +#87526 = CYLINDRICAL_SURFACE ( 'NONE', #24983, 0.05000000000000012768 ) ; +#87527 = ORIENTED_EDGE ( 'NONE', *, *, #98068, .F. ) ; +#87528 = PRESENTATION_STYLE_ASSIGNMENT (( #64061 ) ) ; +#87529 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87530 = FACE_OUTER_BOUND ( 'NONE', #26624, .T. ) ; +#87531 = PLANE ( 'NONE', #97825 ) ; +#87532 = CIRCLE ( 'NONE', #43281, 0.1999999999999996503 ) ; +#87533 = FILL_AREA_STYLE ('',( #64558 ) ) ; +#87534 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87535 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87536 = CARTESIAN_POINT ( 'NONE', ( 3.383841750250087266, 4.963071249749912539, 0.8648700000000000276 ) ) ; +#87537 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.600000000000000089, 0.000000000000000000 ) ) ; +#87538 = AXIS2_PLACEMENT_3D ( 'NONE', #30843, #30319, #85473 ) ; +#87539 = DIRECTION ( 'NONE', ( -0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#87540 = SURFACE_STYLE_USAGE ( .BOTH. , #57951 ) ; +#87541 = FILL_AREA_STYLE ('',( #63584 ) ) ; +#87543 = ADVANCED_FACE ( 'NONE', ( #95404 ), #31136, .T. ) ; +#87542 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#87544 = EDGE_CURVE ( 'NONE', #23423, #10613, #4504, .T. ) ; +#87545 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 3.831700999999999802, 0.8991599999999999593 ) ) ; +#87546 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#87547 = VECTOR ( 'NONE', #27961, 1000.000000000000000 ) ; +#87548 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#87549 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87550 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#87551 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74517 ) ) ; +#87552 = ORIENTED_EDGE ( 'NONE', *, *, #62542, .T. ) ; +#87553 = ORIENTED_EDGE ( 'NONE', *, *, #21840, .T. ) ; +#87554 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#87555 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63083 ), #76099 ) ; +#87556 = CARTESIAN_POINT ( 'NONE', ( 0.2283082038525930113, -1.316727038456209975, 0.8100000000000000533 ) ) ; +#87557 = LINE ( 'NONE', #63087, #39407 ) ; +#87558 = FACE_OUTER_BOUND ( 'NONE', #89778, .T. ) ; +#87559 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87560 = ORIENTED_EDGE ( 'NONE', *, *, #63383, .F. ) ; +#87561 = PLANE ( 'NONE', #55267 ) ; +#87562 = VECTOR ( 'NONE', #12091, 1000.000000000000000 ) ; +#87563 = EDGE_CURVE ( 'NONE', #76537, #65708, #66795, .T. ) ; +#87564 = STYLED_ITEM ( 'NONE', ( #54810 ), #100073 ) ; +#87565 = DIRECTION ( 'NONE', ( 0.9990832187810425591, 0.04281030191567687659, 0.000000000000000000 ) ) ; +#87566 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4600000000000000200, -0.2350000000000000144 ) ) ; +#87567 = VERTEX_POINT ( 'NONE', #3531 ) ; +#87568 = ADVANCED_FACE ( 'NONE', ( #51013 ), #50519, .T. ) ; +#87569 = FILL_AREA_STYLE_COLOUR ( '', #97289 ) ; +#87570 = STYLED_ITEM ( 'NONE', ( #25113 ), #14482 ) ; +#87571 = FILL_AREA_STYLE ('',( #81456 ) ) ; +#87572 = LINE ( 'NONE', #72248, #9712 ) ; +#87573 = SURFACE_STYLE_USAGE ( .BOTH. , #89093 ) ; +#87574 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#87575 = ORIENTED_EDGE ( 'NONE', *, *, #88128, .T. ) ; +#87576 = FILL_AREA_STYLE_COLOUR ( '', #12238 ) ; +#87577 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#87578 = STYLED_ITEM ( 'NONE', ( #44492 ), #13428 ) ; +#87579 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6876, 'distance_accuracy_value', 'NONE'); +#87580 = FILL_AREA_STYLE ('',( #68819 ) ) ; +#87581 = DIRECTION ( 'NONE', ( -0.7974221540510217920, 0.6034218327411003946, 0.000000000000000000 ) ) ; +#87582 = SURFACE_SIDE_STYLE ('',( #24829 ) ) ; +#87583 = ORIENTED_EDGE ( 'NONE', *, *, #93350, .T. ) ; +#87584 = EDGE_CURVE ( 'NONE', #62506, #68868, #73481, .T. ) ; +#87585 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87586 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87587 = CARTESIAN_POINT ( 'NONE', ( -0.1450079136436681349, -1.164927051866627927, 0.8299999999999999600 ) ) ; +#87588 = PLANE ( 'NONE', #61887 ) ; +#87589 = VECTOR ( 'NONE', #31502, 1000.000000000000000 ) ; +#87590 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#87591 = STYLED_ITEM ( 'NONE', ( #62290 ), #30601 ) ; +#87592 = EDGE_CURVE ( 'NONE', #56090, #57896, #57686, .T. ) ; +#87593 = ORIENTED_EDGE ( 'NONE', *, *, #13367, .T. ) ; +#87595 = ORIENTED_EDGE ( 'NONE', *, *, #90835, .F. ) ; +#87594 = FILL_AREA_STYLE_COLOUR ( '', #10009 ) ; +#87596 = VECTOR ( 'NONE', #69260, 1000.000000000000000 ) ; +#87597 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23570, 'distance_accuracy_value', 'NONE'); +#87598 = SURFACE_STYLE_FILL_AREA ( #87101 ) ; +#87599 = SURFACE_STYLE_FILL_AREA ( #32975 ) ; +#87600 = SURFACE_SIDE_STYLE ('',( #78425 ) ) ; +#87601 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689975, 0.4849999999999998757, -0.2399999999999999356 ) ) ; +#87602 = VERTEX_POINT ( 'NONE', #88288 ) ; +#87603 = VECTOR ( 'NONE', #37572, 1000.000000000000000 ) ; +#87604 = LINE ( 'NONE', #64625, #66041 ) ; +#87605 = PRESENTATION_STYLE_ASSIGNMENT (( #54971 ) ) ; +#87606 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87607 = VERTEX_POINT ( 'NONE', #18821 ) ; +#87608 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75751 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97631, #98100, #50246 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87609 = LINE ( 'NONE', #24342, #81422 ) ; +#87610 = ORIENTED_EDGE ( 'NONE', *, *, #33519, .F. ) ; +#87611 = ORIENTED_EDGE ( 'NONE', *, *, #77052, .F. ) ; +#87612 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87613 = STYLED_ITEM ( 'NONE', ( #48316 ), #16980 ) ; +#87614 = LINE ( 'NONE', #88131, #71171 ) ; +#87615 = SURFACE_STYLE_USAGE ( .BOTH. , #56514 ) ; +#87616 = EDGE_CURVE ( 'NONE', #16570, #66007, #4018, .T. ) ; +#87617 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87618 = CARTESIAN_POINT ( 'NONE', ( 10.82260475024997604, 4.397386249750026010, 0.8648700000000000276 ) ) ; +#87619 = ORIENTED_EDGE ( 'NONE', *, *, #18425, .F. ) ; +#87620 = VECTOR ( 'NONE', #74859, 1000.000000000000000 ) ; +#87621 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 5.988375999999999699, 0.8648700000000000276 ) ) ; +#87622 = EDGE_LOOP ( 'NONE', ( #407, #51542, #84194, #17652 ) ) ; +#87623 = SURFACE_STYLE_USAGE ( .BOTH. , #63663 ) ; +#87624 = ORIENTED_EDGE ( 'NONE', *, *, #79970, .F. ) ; +#87625 = ORIENTED_EDGE ( 'NONE', *, *, #55301, .F. ) ; +#87626 = CLOSED_SHELL ( 'NONE', ( #99251, #19976, #8186, #84517, #77115, #62795 ) ) ; +#87628 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87627 = PRESENTATION_STYLE_ASSIGNMENT (( #34032 ) ) ; +#87629 = SURFACE_SIDE_STYLE ('',( #79487 ) ) ; +#87630 = EDGE_CURVE ( 'NONE', #41134, #87351, #72966, .T. ) ; +#87631 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #97359 ) ; +#87632 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87633 = PRESENTATION_STYLE_ASSIGNMENT (( #3862 ) ) ; +#87634 = VECTOR ( 'NONE', #99998, 1000.000000000000000 ) ; +#87635 = AXIS2_PLACEMENT_3D ( 'NONE', #37536, #47179, #23716 ) ; +#87636 = EDGE_CURVE ( 'NONE', #100076, #19475, #77329, .T. ) ; +#87637 = LINE ( 'NONE', #88149, #67436 ) ; +#87638 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2500000001077751222, -4.336808749769470492E-19 ) ) ; +#87639 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#87640 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87641 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #95555 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21933, #43908, #53093 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87642 = ORIENTED_EDGE ( 'NONE', *, *, #68634, .T. ) ; +#87643 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87644 = EDGE_CURVE ( 'NONE', #59512, #42796, #49490, .T. ) ; +#87646 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87645 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#87647 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#87648 = FILL_AREA_STYLE_COLOUR ( '', #55027 ) ; +#87649 = PLANE ( 'NONE', #11967 ) ; +#87650 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87651 = EDGE_CURVE ( 'NONE', #55510, #36490, #67291, .T. ) ; +#87652 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87653 = EDGE_LOOP ( 'NONE', ( #63038, #32988, #38873, #60517 ) ) ; +#87655 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38142, 'distance_accuracy_value', 'NONE'); +#87654 = FILL_AREA_STYLE_COLOUR ( '', #73816 ) ; +#87656 = FILL_AREA_STYLE_COLOUR ( '', #66830 ) ; +#87657 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87658 = FILL_AREA_STYLE ('',( #40713 ) ) ; +#87659 = AXIS2_PLACEMENT_3D ( 'NONE', #18869, #9135, #79692 ) ; +#87660 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#87661 = FACE_OUTER_BOUND ( 'NONE', #23211, .T. ) ; +#87662 = FILL_AREA_STYLE ('',( #49893 ) ) ; +#87663 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#87664 = ADVANCED_FACE ( 'NONE', ( #36188 ), #63059, .T. ) ; +#87665 = ADVANCED_FACE ( 'NONE', ( #39055 ), #23240, .F. ) ; +#87666 = PRESENTATION_STYLE_ASSIGNMENT (( #40214 ) ) ; +#87667 = PLANE ( 'NONE', #84666 ) ; +#87668 = SURFACE_STYLE_FILL_AREA ( #31020 ) ; +#87669 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87670 = PLANE ( 'NONE', #16983 ) ; +#87671 = EDGE_CURVE ( 'NONE', #52295, #44962, #98369, .T. ) ; +#87672 = EDGE_CURVE ( 'NONE', #10613, #14593, #29001, .T. ) ; +#87673 = CARTESIAN_POINT ( 'NONE', ( 1.897707761045830166, -1.292112914554750080, 0.8100000000000004974 ) ) ; +#87674 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59616 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60690, #83669, #43840 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87675 = AXIS2_PLACEMENT_3D ( 'NONE', #35948, #19593, #50778 ) ; +#87676 = ORIENTED_EDGE ( 'NONE', *, *, #55157, .F. ) ; +#87678 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82727 ), #38693 ) ; +#87677 = FILL_AREA_STYLE_COLOUR ( '', #22582 ) ; +#87679 = LINE ( 'NONE', #94805, #30555 ) ; +#87680 = SURFACE_STYLE_FILL_AREA ( #100842 ) ; +#87682 = LINE ( 'NONE', #42244, #51925 ) ; +#87681 = FILL_AREA_STYLE ('',( #78501 ) ) ; +#87683 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#87684 = FILL_AREA_STYLE ('',( #72876 ) ) ; +#87685 = STYLED_ITEM ( 'NONE', ( #100282 ), #17026 ) ; +#87686 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#87687 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.251909075926970427, 0.8299999999999999600 ) ) ; +#87688 = ORIENTED_EDGE ( 'NONE', *, *, #92442, .F. ) ; +#87689 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63308 ), #66477 ) ; +#87690 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000555, 0.6500000000000001332 ) ) ; +#87691 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.29270000000000174, 0.8648700000000000276 ) ) ; +#87692 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87693 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#87694 = VECTOR ( 'NONE', #36728, 1000.000000000000000 ) ; +#87695 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87696 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87697 = CLOSED_SHELL ( 'NONE', ( #74196, #62794, #91510, #94309, #2297, #31131 ) ) ; +#87698 = VECTOR ( 'NONE', #91419, 1000.000000000000000 ) ; +#87699 = ORIENTED_EDGE ( 'NONE', *, *, #83287, .F. ) ; +#87700 = ORIENTED_EDGE ( 'NONE', *, *, #42519, .F. ) ; +#87701 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58374 ), #24097 ) ; +#87702 = FILL_AREA_STYLE_COLOUR ( '', #6334 ) ; +#87703 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#87704 = ORIENTED_EDGE ( 'NONE', *, *, #42682, .F. ) ; +#87705 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87706 = AXIS2_PLACEMENT_3D ( 'NONE', #14366, #92977, #99585 ) ; +#87707 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#87708 = VECTOR ( 'NONE', #26484, 1000.000000000000000 ) ; +#87709 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #17573 ) ; +#87710 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#87711 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87712 = AXIS2_PLACEMENT_3D ( 'NONE', #72988, #80161, #26038 ) ; +#87714 = VERTEX_POINT ( 'NONE', #84992 ) ; +#87713 = VERTEX_POINT ( 'NONE', #53868 ) ; +#87715 = ADVANCED_FACE ( 'NONE', ( #71196 ), #34438, .F. ) ; +#87716 = EDGE_LOOP ( 'NONE', ( #33525, #47771, #85043, #76549 ) ) ; +#87717 = VERTEX_POINT ( 'NONE', #64553 ) ; +#87718 = SURFACE_STYLE_USAGE ( .BOTH. , #57621 ) ; +#87719 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91526, 'distance_accuracy_value', 'NONE'); +#87720 = SURFACE_SIDE_STYLE ('',( #58625 ) ) ; +#87722 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#87721 = SURFACE_STYLE_USAGE ( .BOTH. , #25458 ) ; +#87723 = ORIENTED_EDGE ( 'NONE', *, *, #67196, .F. ) ; +#87724 = EDGE_CURVE ( 'NONE', #61263, #33415, #49757, .T. ) ; +#87725 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87726 = AXIS2_PLACEMENT_3D ( 'NONE', #30654, #61849, #93926 ) ; +#87727 = ORIENTED_EDGE ( 'NONE', *, *, #15272, .F. ) ; +#87728 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87730 = ORIENTED_EDGE ( 'NONE', *, *, #56707, .T. ) ; +#87729 = AXIS2_PLACEMENT_3D ( 'NONE', #54380, #732, #63564 ) ; +#87732 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87731 = FACE_OUTER_BOUND ( 'NONE', #67374, .T. ) ; +#87733 = EDGE_LOOP ( 'NONE', ( #90479, #23609, #2758, #5147 ) ) ; +#87734 = ORIENTED_EDGE ( 'NONE', *, *, #96629, .T. ) ; +#87735 = AXIS2_PLACEMENT_3D ( 'NONE', #20197, #67169, #59061 ) ; +#87736 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988232, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#87737 = EDGE_CURVE ( 'NONE', #80806, #188, #18046, .T. ) ; +#87739 = ORIENTED_EDGE ( 'NONE', *, *, #24646, .T. ) ; +#87738 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#87740 = VECTOR ( 'NONE', #5167, 1000.000000000000000 ) ; +#87741 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87742 = VECTOR ( 'NONE', #94178, 1000.000000000000114 ) ; +#87743 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27935 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13357, #68546, #16412 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87744 = CARTESIAN_POINT ( 'NONE', ( -0.2218544649797319912, -0.9305358755170231033, 0.8100000000000000533 ) ) ; +#87745 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, -3.500000000000000444, 0.000000000000000000 ) ) ; +#87746 = ORIENTED_EDGE ( 'NONE', *, *, #10433, .T. ) ; +#87747 = PLANE ( 'NONE', #6078 ) ; +#87748 = ORIENTED_EDGE ( 'NONE', *, *, #69671, .F. ) ; +#87749 = ORIENTED_EDGE ( 'NONE', *, *, #86874, .F. ) ; +#87750 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87751 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22283 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53524, #90817, #44319 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87752 = ADVANCED_FACE ( 'NONE', ( #47719 ), #55907, .T. ) ; +#87753 = SURFACE_STYLE_FILL_AREA ( #8028 ) ; +#87754 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87755 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87756 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20493, #91451, #12254, #59356 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87757 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87758 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46952, 'distance_accuracy_value', 'NONE'); +#87759 = PLANE ( 'NONE', #47486 ) ; +#87760 = ORIENTED_EDGE ( 'NONE', *, *, #34185, .F. ) ; +#87761 = CARTESIAN_POINT ( 'NONE', ( -1.633333333333333304, -3.500000000000000000, 0.000000000000000000 ) ) ; +#87762 = STYLED_ITEM ( 'NONE', ( #77866 ), #63091 ) ; +#87763 = VERTEX_POINT ( 'NONE', #64059 ) ; +#87764 = EDGE_CURVE ( 'NONE', #33508, #48855, #41085, .T. ) ; +#87765 = LINE ( 'NONE', #33143, #94508 ) ; +#87766 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -0.9000000000000003553, -0.02000000000000000042 ) ) ; +#87767 = PLANE ( 'NONE', #58261 ) ; +#87768 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17624 ), #45305 ) ; +#87769 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87770 = PLANE ( 'NONE', #63400 ) ; +#87772 = FILL_AREA_STYLE ('',( #88281 ) ) ; +#87771 = LINE ( 'NONE', #66657, #64235 ) ; +#87773 = CARTESIAN_POINT ( 'NONE', ( 8.383087000000001510, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#87774 = FACE_OUTER_BOUND ( 'NONE', #25298, .T. ) ; +#87775 = CLOSED_SHELL ( 'NONE', ( #25691, #50881, #55573, #26649, #50598, #93734 ) ) ; +#87776 = ADVANCED_FACE ( 'NONE', ( #96165 ), #56425, .T. ) ; +#87777 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87778 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29997 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36336, #66960, #90952 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87779 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87780 = PRESENTATION_STYLE_ASSIGNMENT (( #25514 ) ) ; +#87781 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87782 = EDGE_CURVE ( 'NONE', #91193, #40777, #68030, .T. ) ; +#87783 = FILL_AREA_STYLE ('',( #1522 ) ) ; +#87784 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#87785 = FILL_AREA_STYLE_COLOUR ( '', #22893 ) ; +#87786 = CARTESIAN_POINT ( 'NONE', ( 5.646583124875012238, 9.827965875124986539, 0.8648700000000000276 ) ) ; +#87787 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#87789 = ADVANCED_FACE ( 'NONE', ( #44554 ), #81898, .F. ) ; +#87788 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79648 ) ) ; +#87790 = ADVANCED_FACE ( 'NONE', ( #43558 ), #58939, .T. ) ; +#87791 = EDGE_LOOP ( 'NONE', ( #58511, #96373, #14592, #13029 ) ) ; +#87792 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#87793 = CARTESIAN_POINT ( 'NONE', ( 1.688788655318780085, -0.9001377335631759458, 0.8100000000000000533 ) ) ; +#87795 = MANIFOLD_SOLID_BREP ( 'ÊäÈë144', #24093 ) ; +#87794 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25282, 'distance_accuracy_value', 'NONE'); +#87796 = ORIENTED_EDGE ( 'NONE', *, *, #59425, .F. ) ; +#87797 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71957, 'distance_accuracy_value', 'NONE'); +#87798 = CARTESIAN_POINT ( 'NONE', ( 1.877768173756620085, -1.057175192472970204, 0.8299999999999999600 ) ) ; +#87799 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000007327, 3.149999999999979927, 0.000000000000000000 ) ) ; +#87800 = EDGE_CURVE ( 'NONE', #46484, #16675, #83395, .T. ) ; +#87801 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #6598, .NOT_KNOWN. ) ; +#87802 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#87803 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#87804 = CARTESIAN_POINT ( 'NONE', ( 0.7761769480519481457, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#87805 = EDGE_CURVE ( 'NONE', #69464, #14803, #21590, .T. ) ; +#87806 = CONICAL_SURFACE ( 'NONE', #4627, 0.5799999999567262421, 0.7853981633974477239 ) ; +#87807 = EDGE_LOOP ( 'NONE', ( #19773, #13788, #90988, #6018 ) ) ; +#87808 = ORIENTED_EDGE ( 'NONE', *, *, #55873, .T. ) ; +#87809 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#87810 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7100, 'distance_accuracy_value', 'NONE'); +#87811 = SURFACE_SIDE_STYLE ('',( #25051 ) ) ; +#87812 = VECTOR ( 'NONE', #27596, 1000.000000000000000 ) ; +#87813 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#87814 = FILL_AREA_STYLE_COLOUR ( '', #55974 ) ; +#87815 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 6.822763000000000133, 0.8991599999999999593 ) ) ; +#87816 = SURFACE_STYLE_FILL_AREA ( #25551 ) ; +#87817 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.7000000000000012879, 0.1829999999999659677 ) ) ; +#87818 = ORIENTED_EDGE ( 'NONE', *, *, #52559, .T. ) ; +#87820 = DIRECTION ( 'NONE', ( 0.7071064476869689530, -0.7071071146859689849, 0.000000000000000000 ) ) ; +#87819 = VECTOR ( 'NONE', #84039, 1000.000000000000000 ) ; +#87821 = PLANE ( 'NONE', #73843 ) ; +#87822 = ORIENTED_EDGE ( 'NONE', *, *, #76245, .T. ) ; +#87823 = SURFACE_STYLE_FILL_AREA ( #25562 ) ; +#87824 = ORIENTED_EDGE ( 'NONE', *, *, #4043, .F. ) ; +#87825 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#87826 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.123820061220085265, 0.000000000000000000 ) ) ; +#87827 = SURFACE_SIDE_STYLE ('',( #55707 ) ) ; +#87828 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30727 ) ) ; +#87829 = CARTESIAN_POINT ( 'NONE', ( -1.115369118623960043, -0.9585098101514269997, 0.8100000000000000533 ) ) ; +#87830 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#87832 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36554 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34081, #74868, #27409 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87831 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87833 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87835 = ORIENTED_EDGE ( 'NONE', *, *, #6333, .F. ) ; +#87834 = ORIENTED_EDGE ( 'NONE', *, *, #24774, .F. ) ; +#87836 = VECTOR ( 'NONE', #99693, 1000.000000000000000 ) ; +#87837 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.000000000000000000 ) ) ; +#87839 = VECTOR ( 'NONE', #24304, 1000.000000000000000 ) ; +#87838 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87840 = ORIENTED_EDGE ( 'NONE', *, *, #12206, .T. ) ; +#87841 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.599999999999999645, 0.000000000000000000 ) ) ; +#87843 = SURFACE_SIDE_STYLE ('',( #40903 ) ) ; +#87842 = SURFACE_STYLE_USAGE ( .BOTH. , #87334 ) ; +#87844 = ORIENTED_EDGE ( 'NONE', *, *, #69906, .F. ) ; +#87845 = EDGE_CURVE ( 'NONE', #48839, #65278, #92513, .T. ) ; +#87846 = ORIENTED_EDGE ( 'NONE', *, *, #7446, .F. ) ; +#87847 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.549999999999999822, 0.000000000000000000 ) ) ; +#87848 = FILL_AREA_STYLE_COLOUR ( '', #3987 ) ; +#87849 = FACE_OUTER_BOUND ( 'NONE', #60208, .T. ) ; +#87850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87851 = LINE ( 'NONE', #71535, #18107 ) ; +#87852 = ORIENTED_EDGE ( 'NONE', *, *, #58811, .F. ) ; +#87853 = VERTEX_POINT ( 'NONE', #60437 ) ; +#87854 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.000000000000000000 ) ) ; +#87855 = ORIENTED_EDGE ( 'NONE', *, *, #33046, .T. ) ; +#87856 = AXIS2_PLACEMENT_3D ( 'NONE', #45680, #6354, #90687 ) ; +#87857 = SURFACE_STYLE_FILL_AREA ( #10144 ) ; +#87860 = ORIENTED_EDGE ( 'NONE', *, *, #51697, .F. ) ; +#87859 = VECTOR ( 'NONE', #72475, 1000.000000000000000 ) ; +#87858 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#87861 = SURFACE_STYLE_USAGE ( .BOTH. , #27612 ) ; +#87862 = FILL_AREA_STYLE ('',( #24616 ) ) ; +#87863 = ORIENTED_EDGE ( 'NONE', *, *, #10507, .T. ) ; +#87864 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.40000000000000036 ) ) ; +#87865 = VERTEX_POINT ( 'NONE', #91536 ) ; +#87866 = ADVANCED_FACE ( 'NONE', ( #15918 ), #30738, .T. ) ; +#87867 = SURFACE_STYLE_USAGE ( .BOTH. , #12190 ) ; +#87868 = PLANE ( 'NONE', #13947 ) ; +#87869 = CARTESIAN_POINT ( 'NONE', ( -1.014711377400389969, -1.276477384597439979, 0.8300000000000000711 ) ) ; +#87870 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#87871 = FILL_AREA_STYLE_COLOUR ( '', #89529 ) ; +#87872 = CIRCLE ( 'NONE', #96008, 0.09999999999999999167 ) ; +#87874 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.266666666666659946, 0.000000000000000000 ) ) ; +#87873 = CARTESIAN_POINT ( 'NONE', ( -0.5270515209870371143, -1.185371998014913331, 0.8299999999999999600 ) ) ; +#87875 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87876 = CARTESIAN_POINT ( 'NONE', ( 9.535670875125044077, 3.110451875125043841, 0.8648700000000000276 ) ) ; +#87877 = EDGE_LOOP ( 'NONE', ( #9405, #90862, #79145, #89841 ) ) ; +#87878 = FILL_AREA_STYLE_COLOUR ( '', #92933 ) ; +#87879 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -3.233333333333333393, 0.000000000000000000 ) ) ; +#87880 = ORIENTED_EDGE ( 'NONE', *, *, #89272, .F. ) ; +#87881 = SURFACE_STYLE_FILL_AREA ( #9187 ) ; +#87882 = VECTOR ( 'NONE', #28337, 1000.000000000000000 ) ; +#87883 = FILL_AREA_STYLE_COLOUR ( '', #4279 ) ; +#87884 = STYLED_ITEM ( 'NONE', ( #69963 ), #85067 ) ; +#87885 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19749 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47743, #78886, #94680 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87886 = SURFACE_STYLE_USAGE ( .BOTH. , #65396 ) ; +#87887 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87888 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87889 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -1.966666666666667007, 0.000000000000000000 ) ) ; +#87890 = EDGE_CURVE ( 'NONE', #63162, #16321, #60927, .T. ) ; +#87891 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17748 ), #97476 ) ; +#87892 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#87893 = AXIS2_PLACEMENT_3D ( 'NONE', #13659, #92324, #75513 ) ; +#87894 = SURFACE_STYLE_USAGE ( .BOTH. , #24122 ) ; +#87895 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#87896 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19766 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65267, #26488, #9554 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87897 = ORIENTED_EDGE ( 'NONE', *, *, #88738, .T. ) ; +#87898 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#87899 = VECTOR ( 'NONE', #65718, 1000.000000000000000 ) ; +#87900 = PRESENTATION_STYLE_ASSIGNMENT (( #25633 ) ) ; +#87901 = VECTOR ( 'NONE', #15511, 1000.000000000000000 ) ; +#87902 = SURFACE_STYLE_FILL_AREA ( #97899 ) ; +#87903 = VECTOR ( 'NONE', #78897, 1000.000000000000000 ) ; +#87904 = EDGE_CURVE ( 'NONE', #21416, #81104, #91744, .T. ) ; +#87905 = FACE_OUTER_BOUND ( 'NONE', #16262, .T. ) ; +#87906 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#87907 = VERTEX_POINT ( 'NONE', #7686 ) ; +#87908 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#87909 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.09999999999999870104, 6.355796620655076481E-79 ) ) ; +#87910 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87911 = FILL_AREA_STYLE_COLOUR ( '', #84447 ) ; +#87912 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.463023860841316052E-78, -1.991364888915569965E-47 ) ) ; +#87913 = LINE ( 'NONE', #32790, #9056 ) ; +#87914 = VECTOR ( 'NONE', #37434, 1000.000000000000000 ) ; +#87915 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87916 = CARTESIAN_POINT ( 'NONE', ( -1.132903271161860070, -1.445215125000139933, 0.8300000000000001821 ) ) ; +#87917 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90350, 'distance_accuracy_value', 'NONE'); +#87918 = VECTOR ( 'NONE', #19096, 1000.000000000000000 ) ; +#87919 = EDGE_CURVE ( 'NONE', #56137, #7722, #70049, .T. ) ; +#87920 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#87921 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#87922 = EDGE_LOOP ( 'NONE', ( #28086, #36276, #55321, #12442 ) ) ; +#87923 = ORIENTED_EDGE ( 'NONE', *, *, #86010, .T. ) ; +#87924 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.266666666666659946, 3.495651678170121160E-76 ) ) ; +#87925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49483, 'distance_accuracy_value', 'NONE'); +#87926 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28993, 'distance_accuracy_value', 'NONE'); +#87927 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10096 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83176, #36713, #44827 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87928 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87929 = SURFACE_STYLE_FILL_AREA ( #87426 ) ; +#87930 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#87931 = SURFACE_STYLE_FILL_AREA ( #89448 ) ; +#87932 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87933 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999980016, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#87934 = DIRECTION ( 'NONE', ( -0.3516809254569017162, 0.000000000000000000, 0.9361199317767874284 ) ) ; +#87935 = ORIENTED_EDGE ( 'NONE', *, *, #11777, .T. ) ; +#87936 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#87937 = LINE ( 'NONE', #73633, #59689 ) ; +#87938 = LINE ( 'NONE', #31799, #45417 ) ; +#87939 = EDGE_LOOP ( 'NONE', ( #90014, #47137, #57341, #20327 ) ) ; +#87940 = PRESENTATION_STYLE_ASSIGNMENT (( #41005 ) ) ; +#87941 = AXIS2_PLACEMENT_3D ( 'NONE', #26802, #9365, #26300 ) ; +#87942 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#87943 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99216 ) ) ; +#87944 = ORIENTED_EDGE ( 'NONE', *, *, #66309, .F. ) ; +#87945 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1636, #85875, #16388, #78229 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87946 = CARTESIAN_POINT ( 'NONE', ( 2.966666666666660124, -3.500000000000000000, 0.000000000000000000 ) ) ; +#87947 = AXIS2_PLACEMENT_3D ( 'NONE', #86475, #55370, #69617 ) ; +#87948 = VECTOR ( 'NONE', #97783, 1000.000000000000000 ) ; +#87949 = SURFACE_STYLE_FILL_AREA ( #58865 ) ; +#87950 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#87951 = FACE_OUTER_BOUND ( 'NONE', #15363, .T. ) ; +#87952 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#87953 = VERTEX_POINT ( 'NONE', #31257 ) ; +#87954 = CARTESIAN_POINT ( 'NONE', ( 9.650000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#87955 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64711 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13020, #68204, #12005 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87957 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#87956 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7976 ) ) ; +#87958 = ORIENTED_EDGE ( 'NONE', *, *, #41374, .F. ) ; +#87959 = VECTOR ( 'NONE', #35583, 1000.000000000000000 ) ; +#87960 = SURFACE_SIDE_STYLE ('',( #4202 ) ) ; +#87961 = EDGE_CURVE ( 'NONE', #89309, #59435, #62428, .T. ) ; +#87962 = VECTOR ( 'NONE', #83941, 1000.000000000000000 ) ; +#87963 = MANIFOLD_SOLID_BREP ( 'ÊäÈë76', #56761 ) ; +#87964 = ORIENTED_EDGE ( 'NONE', *, *, #15741, .F. ) ; +#87965 = PLANE ( 'NONE', #83979 ) ; +#87966 = FILL_AREA_STYLE ('',( #41516 ) ) ; +#87967 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#87968 = VECTOR ( 'NONE', #85494, 1000.000000000000114 ) ; +#87969 = FILL_AREA_STYLE_COLOUR ( '', #24369 ) ; +#87970 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87971 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#87972 = ORIENTED_EDGE ( 'NONE', *, *, #91121, .T. ) ; +#87973 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #87133, #21453, #83276, #82894 ), #14322 ) ; +#87975 = EDGE_LOOP ( 'NONE', ( #90855, #88484, #76748, #79868, #77852, #55377, #76789, #55126, #6631, #70342 ) ) ; +#87974 = ORIENTED_EDGE ( 'NONE', *, *, #83250, .T. ) ; +#87976 = EDGE_LOOP ( 'NONE', ( #35688, #36741, #95447, #33825 ) ) ; +#87977 = LINE ( 'NONE', #33370, #88358 ) ; +#87978 = STYLED_ITEM ( 'NONE', ( #79113 ), #64065 ) ; +#87979 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42834 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68018, #62808, #4745 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#87980 = ORIENTED_EDGE ( 'NONE', *, *, #15147, .F. ) ; +#87982 = ORIENTED_EDGE ( 'NONE', *, *, #95907, .T. ) ; +#87981 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.699999999999999734, 0.1829999999999999960 ) ) ; +#87983 = SURFACE_STYLE_USAGE ( .BOTH. , #64505 ) ; +#87985 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#87984 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87986 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87987 = DIRECTION ( 'NONE', ( 0.9317134237021232890, 0.000000000000000000, 0.3631942952377801292 ) ) ; +#87988 = ORIENTED_EDGE ( 'NONE', *, *, #39885, .F. ) ; +#87989 = CARTESIAN_POINT ( 'NONE', ( 1.719030235149860086, -1.443664018207750255, 0.8099999999999997202 ) ) ; +#87990 = ORIENTED_EDGE ( 'NONE', *, *, #84322, .F. ) ; +#87991 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50787, #59463, #19090, #34459 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#87992 = EDGE_CURVE ( 'NONE', #14561, #22291, #47081, .T. ) ; +#87993 = LINE ( 'NONE', #2740, #98502 ) ; +#87994 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#87995 = ORIENTED_EDGE ( 'NONE', *, *, #51464, .T. ) ; +#87996 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#87997 = EDGE_CURVE ( 'NONE', #31313, #94098, #71080, .T. ) ; +#87998 = EDGE_CURVE ( 'NONE', #31588, #27237, #78724, .T. ) ; +#87999 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2849999999999999756, 0.1499999999999999944 ) ) ; +#88000 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88002 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88001 = SURFACE_SIDE_STYLE ('',( #88505 ) ) ; +#88003 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88004 = SURFACE_SIDE_STYLE ('',( #72683 ) ) ; +#88005 = VECTOR ( 'NONE', #278, 1000.000000000000000 ) ; +#88006 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88007 = FACE_OUTER_BOUND ( 'NONE', #70256, .T. ) ; +#88008 = SURFACE_STYLE_FILL_AREA ( #10300 ) ; +#88010 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88009 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#88011 = ADVANCED_FACE ( 'NONE', ( #87905 ), #40967, .F. ) ; +#88012 = EDGE_CURVE ( 'NONE', #85090, #93951, #56296, .T. ) ; +#88013 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1661 ), #22866 ) ; +#88014 = CARTESIAN_POINT ( 'NONE', ( -1.111006624335320048, -0.8869042198941200494, 0.8299999999999999600 ) ) ; +#88015 = CARTESIAN_POINT ( 'NONE', ( 0.9858795606121630861, -1.017871276266119951, 0.8299999999999999600 ) ) ; +#88016 = VERTEX_POINT ( 'NONE', #63454 ) ; +#88017 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88018 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#88019 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88020 = CARTESIAN_POINT ( 'NONE', ( 4.392685551145265599, 1.433688990682459918, -11.91924037663980052 ) ) ; +#88021 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #56985, #90915, #76083, #6573 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88022 = AXIS2_PLACEMENT_3D ( 'NONE', #78550, #22420, #54080 ) ; +#88023 = AXIS2_PLACEMENT_3D ( 'NONE', #94855, #56633, #15746 ) ; +#88024 = ORIENTED_EDGE ( 'NONE', *, *, #61303, .T. ) ; +#88025 = FILL_AREA_STYLE ('',( #57931 ) ) ; +#88028 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88027 = PRESENTATION_STYLE_ASSIGNMENT (( #65528 ) ) ; +#88026 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88029 = CARTESIAN_POINT ( 'NONE', ( 4.232369750250087215, 4.114543249749912590, 0.8648700000000000276 ) ) ; +#88030 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#88031 = CARTESIAN_POINT ( 'NONE', ( -0.1796601769484260092, -1.431361989143759894, 0.8100000000000000533 ) ) ; +#88032 = CARTESIAN_POINT ( 'NONE', ( 0.3916958651482640441, -1.284685391536070087, 0.8299999999999999600 ) ) ; +#88033 = VECTOR ( 'NONE', #9385, 1000.000000000000000 ) ; +#88034 = EDGE_CURVE ( 'NONE', #63753, #85966, #32282, .T. ) ; +#88035 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45551 ) ) ; +#88036 = FACE_OUTER_BOUND ( 'NONE', #74445, .T. ) ; +#88037 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88038 = CIRCLE ( 'NONE', #42351, 0.1000000000000000194 ) ; +#88039 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88040 = VERTEX_POINT ( 'NONE', #10192 ) ; +#88041 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88042 = SURFACE_STYLE_USAGE ( .BOTH. , #97658 ) ; +#88043 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#88044 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#88045 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000500, 0.1199999999999999956, -0.8499999999999996447 ) ) ; +#88046 = SURFACE_SIDE_STYLE ('',( #72217 ) ) ; +#88047 = SURFACE_STYLE_USAGE ( .BOTH. , #64562 ) ; +#88048 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18105 ) ) ; +#88049 = LINE ( 'NONE', #18059, #76799 ) ; +#88050 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88051 = LINE ( 'NONE', #72722, #8675 ) ; +#88052 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88053 = SURFACE_SIDE_STYLE ('',( #72723 ) ) ; +#88054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51262, 'distance_accuracy_value', 'NONE'); +#88055 = ADVANCED_FACE ( 'NONE', ( #55772 ), #19180, .F. ) ; +#88056 = CARTESIAN_POINT ( 'NONE', ( 1.036559900398249967, -1.306787212278190058, 0.8299999999999999600 ) ) ; +#88057 = PLANE ( 'NONE', #24425 ) ; +#88058 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88059 = EDGE_CURVE ( 'NONE', #53678, #54719, #21712, .T. ) ; +#88060 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.7071067811865474617, -0.7071067811865474617 ) ) ; +#88061 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92875 ), #63654 ) ; +#88062 = VERTEX_POINT ( 'NONE', #88153 ) ; +#88063 = ORIENTED_EDGE ( 'NONE', *, *, #85234, .F. ) ; +#88064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11858, 'distance_accuracy_value', 'NONE'); +#88065 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68646, 'distance_accuracy_value', 'NONE'); +#88066 = VECTOR ( 'NONE', #7814, 1000.000000000000000 ) ; +#88068 = SURFACE_STYLE_USAGE ( .BOTH. , #11370 ) ; +#88067 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #39704, #71352, #64207, #1417 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88069 = FACE_OUTER_BOUND ( 'NONE', #94747, .T. ) ; +#88070 = CARTESIAN_POINT ( 'NONE', ( 1.877470194538120030, -1.043958301690999901, 0.8299999999999999600 ) ) ; +#88071 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 2.594263999999999903, 0.8991599999999999593 ) ) ; +#88072 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#88073 = ORIENTED_EDGE ( 'NONE', *, *, #49884, .T. ) ; +#88074 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88075 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#88076 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78434, 'distance_accuracy_value', 'NONE'); +#88077 = SURFACE_STYLE_USAGE ( .BOTH. , #50800 ) ; +#88078 = VECTOR ( 'NONE', #90345, 1000.000000000000000 ) ; +#88079 = VERTEX_POINT ( 'NONE', #26880 ) ; +#88080 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#88081 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88082 = EDGE_CURVE ( 'NONE', #96973, #4568, #26377, .T. ) ; +#88083 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.01499999999999999944, 0.2399999999999999911 ) ) ; +#88084 = LINE ( 'NONE', #18089, #11976 ) ; +#88085 = VERTEX_POINT ( 'NONE', #90133 ) ; +#88086 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #30997 ) ) ; +#88087 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, 1.129999999999999893 ) ) ; +#88088 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6197, 'distance_accuracy_value', 'NONE'); +#88089 = SURFACE_STYLE_FILL_AREA ( #34994 ) ; +#88090 = LINE ( 'NONE', #63619, #62218 ) ; +#88091 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8100000000000000533 ) ) ; +#88092 = ADVANCED_FACE ( 'NONE', ( #11444 ), #4165, .F. ) ; +#88093 = ORIENTED_EDGE ( 'NONE', *, *, #39940, .F. ) ; +#88094 = LINE ( 'NONE', #2336, #79070 ) ; +#88095 = FACE_OUTER_BOUND ( 'NONE', #88591, .T. ) ; +#88096 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88097 = AXIS2_PLACEMENT_3D ( 'NONE', #75379, #4907, #99745 ) ; +#88098 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88099 = DIRECTION ( 'NONE', ( -0.7071067806865475314, 0.7071067816865476141, -0.000000000000000000 ) ) ; +#88100 = ADVANCED_FACE ( 'NONE', ( #53851 ), #91632, .T. ) ; +#88101 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88102 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88103 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #46881 ) ; +#88104 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16585 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23831, #54984, #52973 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88105 = VECTOR ( 'NONE', #53955, 1000.000000000000000 ) ; +#88106 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #40303, #27436 ) ; +#88107 = ADVANCED_FACE ( 'NONE', ( #67157 ), #21197, .T. ) ; +#88108 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93689 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94244, #55506, #32508 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88109 = VERTEX_POINT ( 'NONE', #83499 ) ; +#88112 = ORIENTED_EDGE ( 'NONE', *, *, #45184, .T. ) ; +#88111 = FILL_AREA_STYLE ('',( #87594 ) ) ; +#88110 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52262 ), #40900 ) ; +#88113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62027 ), #48985 ) ; +#88114 = PRESENTATION_STYLE_ASSIGNMENT (( #79959 ) ) ; +#88116 = FACE_OUTER_BOUND ( 'NONE', #50977, .T. ) ; +#88115 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#88117 = PLANE ( 'NONE', #48069 ) ; +#88118 = SURFACE_SIDE_STYLE ('',( #56994 ) ) ; +#88119 = ORIENTED_EDGE ( 'NONE', *, *, #13034, .T. ) ; +#88120 = AXIS2_PLACEMENT_3D ( 'NONE', #77266, #23169, #94068 ) ; +#88121 = LINE ( 'NONE', #72794, #61186 ) ; +#88122 = LINE ( 'NONE', #2854, #23539 ) ; +#88123 = AXIS2_PLACEMENT_3D ( 'NONE', #50024, #11094, #42343 ) ; +#88124 = SURFACE_STYLE_USAGE ( .BOTH. , #71270 ) ; +#88125 = ORIENTED_EDGE ( 'NONE', *, *, #72319, .T. ) ; +#88126 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88127 = EDGE_LOOP ( 'NONE', ( #60291, #8334, #86225, #58901 ) ) ; +#88128 = EDGE_CURVE ( 'NONE', #22600, #44288, #69115, .T. ) ; +#88129 = ORIENTED_EDGE ( 'NONE', *, *, #98666, .F. ) ; +#88130 = EDGE_CURVE ( 'NONE', #39329, #66135, #40050, .T. ) ; +#88131 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#88132 = VECTOR ( 'NONE', #80382, 1000.000000000000000 ) ; +#88133 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88134 = VECTOR ( 'NONE', #74729, 1000.000000000000114 ) ; +#88135 = FILL_AREA_STYLE_COLOUR ( '', #73462 ) ; +#88136 = ORIENTED_EDGE ( 'NONE', *, *, #89614, .F. ) ; +#88137 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88138 = FACE_OUTER_BOUND ( 'NONE', #59733, .T. ) ; +#88139 = ORIENTED_EDGE ( 'NONE', *, *, #8885, .F. ) ; +#88140 = CARTESIAN_POINT ( 'NONE', ( 1.363488817166419897, -1.341449062141889970, 0.8100000000000000533 ) ) ; +#88141 = ORIENTED_EDGE ( 'NONE', *, *, #16638, .F. ) ; +#88142 = FILL_AREA_STYLE ('',( #2880 ) ) ; +#88143 = CARTESIAN_POINT ( 'NONE', ( -1.346516121155820089, -1.141526082476290060, 0.8100000000000000533 ) ) ; +#88144 = MANIFOLD_SOLID_BREP ( 'ÊäÈë53', #5998 ) ; +#88145 = EDGE_CURVE ( 'NONE', #1165, #98788, #77832, .T. ) ; +#88146 = LINE ( 'NONE', #67028, #44987 ) ; +#88147 = EDGE_CURVE ( 'NONE', #97722, #85774, #7793, .T. ) ; +#88148 = CYLINDRICAL_SURFACE ( 'NONE', #23667, 0.2000000000000000111 ) ; +#88149 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.7000000000000019540, 0.1829999999999659677 ) ) ; +#88151 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88150 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#88152 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88153 = CARTESIAN_POINT ( 'NONE', ( -0.1150138248524561896, 0.2193344754160007348, 0.8100000000000000533 ) ) ; +#88154 = ORIENTED_EDGE ( 'NONE', *, *, #79637, .T. ) ; +#88155 = PLANE ( 'NONE', #60038 ) ; +#88156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88157 = PRESENTATION_STYLE_ASSIGNMENT (( #66170 ) ) ; +#88158 = EDGE_CURVE ( 'NONE', #60664, #6630, #88560, .T. ) ; +#88159 = SURFACE_STYLE_FILL_AREA ( #95268 ) ; +#88160 = FILL_AREA_STYLE ('',( #64670 ) ) ; +#88161 = CARTESIAN_POINT ( 'NONE', ( 1.981625129855739686, 1.439252765030526016, -11.40144131386615989 ) ) ; +#88162 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88163 = EDGE_LOOP ( 'NONE', ( #18749, #51091, #96076, #19869 ) ) ; +#88165 = EDGE_CURVE ( 'NONE', #40001, #97446, #79356, .T. ) ; +#88164 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88166 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.3966667321250390565, 0.6832601347701363625 ) ) ; +#88167 = SURFACE_STYLE_FILL_AREA ( #57056 ) ; +#88168 = FILL_AREA_STYLE ('',( #71329 ) ) ; +#88169 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31079 ) ) ; +#88170 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53389 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8738, #76760, #62479 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88171 = CARTESIAN_POINT ( 'NONE', ( 0.3664728319017789837, -1.220832247304010298, 0.8300000000000015143 ) ) ; +#88172 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81754, 'distance_accuracy_value', 'NONE'); +#88173 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#88174 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88175 = PRESENTATION_STYLE_ASSIGNMENT (( #73856 ) ) ; +#88176 = FILL_AREA_STYLE ('',( #71332 ) ) ; +#88177 = VECTOR ( 'NONE', #80360, 1000.000000000000000 ) ; +#88179 = PRESENTATION_STYLE_ASSIGNMENT (( #88668 ) ) ; +#88178 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81291 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20164, #14483, #91617 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88180 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88181 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.383333333333326642, 0.000000000000000000 ) ) ; +#88182 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88183 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.000000000000000000 ) ) ; +#88184 = EDGE_CURVE ( 'NONE', #32857, #83324, #54884, .T. ) ; +#88185 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#88186 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92994 ), #36007 ) ; +#88187 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3428 ), #36009 ) ; +#88188 = CARTESIAN_POINT ( 'NONE', ( 1.841098443137489937, -1.205608583660890076, 0.8100000000000004974 ) ) ; +#88189 = SURFACE_STYLE_FILL_AREA ( #95801 ) ; +#88190 = FILL_AREA_STYLE_COLOUR ( '', #72258 ) ; +#88191 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#88192 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #78877, 'design' ) ; +#88193 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19875 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65869, #56212, #67350 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88195 = SURFACE_SIDE_STYLE ('',( #49380 ) ) ; +#88196 = ORIENTED_EDGE ( 'NONE', *, *, #43935, .F. ) ; +#88197 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88198 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54139, 'distance_accuracy_value', 'NONE'); +#88199 = SURFACE_SIDE_STYLE ('',( #95811 ) ) ; +#88200 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39146, 'distance_accuracy_value', 'NONE'); +#88201 = PLANE ( 'NONE', #68824 ) ; +#88202 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14740 ) ) ; +#88203 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#88204 = FACE_OUTER_BOUND ( 'NONE', #1670, .T. ) ; +#88205 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.009999999999999998473, -1.250000000000000000 ) ) ; +#88206 = EDGE_CURVE ( 'NONE', #36766, #42173, #9320, .T. ) ; +#88207 = ORIENTED_EDGE ( 'NONE', *, *, #60877, .T. ) ; +#88208 = VECTOR ( 'NONE', #89048, 1000.000000000000000 ) ; +#88209 = VECTOR ( 'NONE', #77169, 1000.000000000000000 ) ; +#88210 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#88211 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #53899, 'distance_accuracy_value', 'NONE'); +#88212 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.123820061220085265, 0.000000000000000000 ) ) ; +#88213 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31851, 'distance_accuracy_value', 'NONE'); +#88214 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88215 = ADVANCED_FACE ( 'NONE', ( #24247 ), #30857, .T. ) ; +#88216 = ORIENTED_EDGE ( 'NONE', *, *, #90001, .T. ) ; +#88217 = ORIENTED_EDGE ( 'NONE', *, *, #33178, .T. ) ; +#88218 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71769, #1829, #80966, #79945, #10894, #72778, #42145, #33996, #96224, #26325, #57479, #88587, #90602, #96720, #4331, #67105, #97705, #34500, #12908, #43613, #13411, #35503, #11398, #66607, #19127, #73783, #44127, #20134, #89104, #65607, #75289, #20643, #11896, #83449 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 1, 1, 2, 2, 1, 1, 1, 1, 2, 2, 1, 1, 2, 2, 1, 1, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000001189326, 0.1875000000001784128, 0.2187500000002076950, 0.2343750000002227940, 0.2500000000002379208, 0.3750000000003450018, 0.4375000000003985701, 0.4687500000004253264, 0.4843750000004387046, 0.4921875000004448109, 0.5000000000004508616, 0.5625000000003959055, 0.5937500000003682610, 0.6093750000003544942, 0.6250000000003407274, 0.6875000000002836620, 0.7187500000002555733, 0.7343750000002415845, 0.7500000000002274847, 0.8750000000001137979, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88219 = PRESENTATION_STYLE_ASSIGNMENT (( #33598 ) ) ; +#88220 = VERTEX_POINT ( 'NONE', #93111 ) ; +#88221 = EDGE_CURVE ( 'NONE', #16589, #61838, #54372, .T. ) ; +#88222 = AXIS2_PLACEMENT_3D ( 'NONE', #57748, #88847, #58250 ) ; +#88223 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#88224 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #23416 ) ; +#88225 = LINE ( 'NONE', #18230, #16612 ) ; +#88226 = LINE ( 'NONE', #94337, #90020 ) ; +#88229 = ORIENTED_EDGE ( 'NONE', *, *, #21615, .T. ) ; +#88228 = VERTEX_POINT ( 'NONE', #35439 ) ; +#88227 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96248, #24854, #32985, #34523 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88230 = EDGE_CURVE ( 'NONE', #22042, #39926, #57401, .T. ) ; +#88231 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31148 ), #93049 ) ; +#88232 = ORIENTED_EDGE ( 'NONE', *, *, #22821, .T. ) ; +#88233 = ORIENTED_EDGE ( 'NONE', *, *, #31286, .T. ) ; +#88234 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88235 = FACE_OUTER_BOUND ( 'NONE', #2584, .T. ) ; +#88237 = CARTESIAN_POINT ( 'NONE', ( 1.408334268560540004, -1.010972591757870021, 0.8100000000000000533 ) ) ; +#88236 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88238 = ORIENTED_EDGE ( 'NONE', *, *, #3240, .F. ) ; +#88239 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88240 = SURFACE_STYLE_FILL_AREA ( #64744 ) ; +#88241 = AXIS2_PLACEMENT_3D ( 'NONE', #53842, #62033, #92129 ) ; +#88242 = VERTEX_POINT ( 'NONE', #74212 ) ; +#88243 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.250000000000000444, -0.02000000000000000042 ) ) ; +#88244 = ORIENTED_EDGE ( 'NONE', *, *, #22749, .T. ) ; +#88245 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, -0.01500000000000000118, 0.2500000000000000000 ) ) ; +#88246 = ORIENTED_EDGE ( 'NONE', *, *, #53694, .T. ) ; +#88247 = ADVANCED_FACE ( 'NONE', ( #50758 ), #57928, .T. ) ; +#88248 = ORIENTED_EDGE ( 'NONE', *, *, #99957, .T. ) ; +#88249 = EDGE_CURVE ( 'NONE', #66870, #96354, #2264, .T. ) ; +#88251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88250 = FILL_AREA_STYLE ('',( #25980 ) ) ; +#88252 = SURFACE_STYLE_FILL_AREA ( #65253 ) ; +#88253 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88254 = ORIENTED_EDGE ( 'NONE', *, *, #23076, .F. ) ; +#88255 = ORIENTED_EDGE ( 'NONE', *, *, #10869, .F. ) ; +#88256 = VECTOR ( 'NONE', #31755, 1000.000000000000000 ) ; +#88257 = CARTESIAN_POINT ( 'NONE', ( -0.2218544649797319912, -0.9305358755170231033, 0.8299999999999999600 ) ) ; +#88258 = FILL_AREA_STYLE ('',( #27486 ) ) ; +#88259 = ORIENTED_EDGE ( 'NONE', *, *, #10753, .T. ) ; +#88261 = PRESENTATION_STYLE_ASSIGNMENT (( #73943 ) ) ; +#88260 = LINE ( 'NONE', #65261, #56379 ) ; +#88262 = CARTESIAN_POINT ( 'NONE', ( 0.03330623534528640017, -1.205608583660890076, 0.8299999999999999600 ) ) ; +#88263 = ORIENTED_EDGE ( 'NONE', *, *, #54612, .T. ) ; +#88264 = EDGE_LOOP ( 'NONE', ( #63494, #58754, #67810, #71515, #85925, #5571 ) ) ; +#88265 = STYLED_ITEM ( 'NONE', ( #88114 ), #7161 ) ; +#88266 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88267 = FILL_AREA_STYLE_COLOUR ( '', #28527 ) ; +#88268 = EDGE_CURVE ( 'NONE', #50925, #60027, #4258, .T. ) ; +#88269 = STYLED_ITEM ( 'NONE', ( #77625 ), #20737 ) ; +#88270 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88271 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.9500000000000009548, -0.02000000000000000042 ) ) ; +#88272 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 10.54921500000000023, 0.8991599999999999593 ) ) ; +#88273 = DIRECTION ( 'NONE', ( 0.7071067806865475314, 0.7071067816865476141, 0.000000000000000000 ) ) ; +#88274 = STYLED_ITEM ( 'NONE', ( #18180 ), #65290 ) ; +#88275 = ORIENTED_EDGE ( 'NONE', *, *, #57660, .T. ) ; +#88276 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#88277 = ORIENTED_EDGE ( 'NONE', *, *, #91657, .T. ) ; +#88278 = STYLED_ITEM ( 'NONE', ( #28096 ), #69631 ) ; +#88279 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88280 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88281 = FILL_AREA_STYLE_COLOUR ( '', #38649 ) ; +#88282 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88283 = FILL_AREA_STYLE ('',( #27013 ) ) ; +#88284 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88285 = FACE_OUTER_BOUND ( 'NONE', #80095, .T. ) ; +#88286 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88287 = LINE ( 'NONE', #80645, #52670 ) ; +#88288 = CARTESIAN_POINT ( 'NONE', ( 10.77310724974991274, 7.261168750250087456, 0.8648700000000000276 ) ) ; +#88289 = AXIS2_PLACEMENT_3D ( 'NONE', #26401, #60075, #4393 ) ; +#88290 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#88291 = CARTESIAN_POINT ( 'NONE', ( 1.408233674637860755, -1.439563048828384151, 0.8099999999997133937 ) ) ; +#88292 = FACE_OUTER_BOUND ( 'NONE', #83855, .T. ) ; +#88293 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96191 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17503, #79316, #64502 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88294 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88295 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88296 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#88297 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88298 = EDGE_CURVE ( 'NONE', #65972, #39488, #72702, .T. ) ; +#88299 = FACE_OUTER_BOUND ( 'NONE', #73960, .T. ) ; +#88300 = LINE ( 'NONE', #87787, #2225 ) ; +#88302 = EDGE_CURVE ( 'NONE', #64282, #61177, #66046, .T. ) ; +#88301 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6612, 'distance_accuracy_value', 'NONE'); +#88303 = ORIENTED_EDGE ( 'NONE', *, *, #78339, .F. ) ; +#88304 = SURFACE_STYLE_USAGE ( .BOTH. , #17829 ) ; +#88305 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #25622 ) ; +#88306 = ORIENTED_EDGE ( 'NONE', *, *, #57592, .F. ) ; +#88307 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1399999999999999856 ) ) ; +#88308 = LINE ( 'NONE', #42852, #73031 ) ; +#88309 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88310 = FILL_AREA_STYLE_COLOUR ( '', #19068 ) ; +#88311 = VECTOR ( 'NONE', #49676, 1000.000000000000000 ) ; +#88312 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52422 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51362, #91145, #89649 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88313 = CIRCLE ( 'NONE', #16552, 0.1679250012421869831 ) ; +#88314 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.149999999999970157, 1.048695503451051965E-76 ) ) ; +#88315 = ORIENTED_EDGE ( 'NONE', *, *, #38218, .F. ) ; +#88316 = EDGE_CURVE ( 'NONE', #90329, #27209, #91899, .T. ) ; +#88317 = ORIENTED_EDGE ( 'NONE', *, *, #28750, .T. ) ; +#88318 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 9.035018104045849247E-16 ) ) ; +#88319 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#88320 = FILL_AREA_STYLE ('',( #65326 ) ) ; +#88321 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 1.149999999999999911, 0.000000000000000000 ) ) ; +#88322 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.1499999999999999944, 0.1900000000000000022 ) ) ; +#88323 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88324 = FILL_AREA_STYLE_COLOUR ( '', #3829 ) ; +#88325 = VERTEX_POINT ( 'NONE', #26757 ) ; +#88326 = PRESENTATION_STYLE_ASSIGNMENT (( #97460 ) ) ; +#88327 = SURFACE_STYLE_FILL_AREA ( #26062 ) ; +#88328 = ORIENTED_EDGE ( 'NONE', *, *, #37427, .T. ) ; +#88329 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#88330 = VERTEX_POINT ( 'NONE', #45035 ) ; +#88331 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88332 = FACE_OUTER_BOUND ( 'NONE', #99171, .T. ) ; +#88333 = SURFACE_STYLE_USAGE ( .BOTH. , #47506 ) ; +#88334 = CARTESIAN_POINT ( 'NONE', ( -1.019254590033279895, -1.033922635360990050, 0.8100000000000000533 ) ) ; +#88335 = PRESENTATION_STYLE_ASSIGNMENT (( #80199 ) ) ; +#88336 = SURFACE_SIDE_STYLE ('',( #25569 ) ) ; +#88337 = SURFACE_STYLE_FILL_AREA ( #57228 ) ; +#88338 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #82696 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8877, #53926, #23292 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88340 = EDGE_LOOP ( 'NONE', ( #4817, #97493, #39576, #98301 ) ) ; +#88339 = ORIENTED_EDGE ( 'NONE', *, *, #47780, .T. ) ; +#88341 = EDGE_CURVE ( 'NONE', #33002, #19650, #83382, .T. ) ; +#88342 = VECTOR ( 'NONE', #2848, 1000.000000000000000 ) ; +#88343 = FILL_AREA_STYLE ('',( #18877 ) ) ; +#88344 = ORIENTED_EDGE ( 'NONE', *, *, #33382, .F. ) ; +#88346 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333313320, -2.500000000000000000, 0.000000000000000000 ) ) ; +#88345 = CARTESIAN_POINT ( 'NONE', ( 9.535671000000000674, 3.110451999999999995, 0.8991599999999999593 ) ) ; +#88347 = ORIENTED_EDGE ( 'NONE', *, *, #25904, .T. ) ; +#88348 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83793 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #41734, #18200, #19750 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88349 = EDGE_CURVE ( 'NONE', #7722, #72535, #83759, .T. ) ; +#88350 = ORIENTED_EDGE ( 'NONE', *, *, #91318, .F. ) ; +#88351 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#88352 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#88353 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#88354 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #93181 ), #73637 ) ; +#88355 = VERTEX_POINT ( 'NONE', #30228 ) ; +#88356 = ORIENTED_EDGE ( 'NONE', *, *, #86173, .F. ) ; +#88357 = SURFACE_STYLE_USAGE ( .BOTH. , #40915 ) ; +#88358 = VECTOR ( 'NONE', #14581, 1000.000000000000000 ) ; +#88359 = EDGE_LOOP ( 'NONE', ( #61756, #82196, #26716, #7430, #83413, #8628 ) ) ; +#88360 = EDGE_CURVE ( 'NONE', #22042, #91087, #5211, .T. ) ; +#88361 = EDGE_CURVE ( 'NONE', #60527, #18285, #67040, .T. ) ; +#88362 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88365 = EDGE_CURVE ( 'NONE', #67996, #87284, #71543, .T. ) ; +#88364 = VERTEX_POINT ( 'NONE', #76702 ) ; +#88363 = CARTESIAN_POINT ( 'NONE', ( 5.929425875125043710, 2.417487124874956095, 0.8648700000000000276 ) ) ; +#88366 = ADVANCED_FACE ( 'NONE', ( #43547 ), #99594, .T. ) ; +#88367 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88368 = CARTESIAN_POINT ( 'NONE', ( 1.702237012380340087, -1.507644428662930025, 0.8099999999999996092 ) ) ; +#88369 = ORIENTED_EDGE ( 'NONE', *, *, #47180, .T. ) ; +#88370 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88371 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#88372 = ORIENTED_EDGE ( 'NONE', *, *, #38218, .T. ) ; +#88373 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #90867, #30063, #14714, #63638, #92349, #53574, #1844, #69340, #91853, #56500, #71267, #1324, #14204, #22413, #94223, #45859, #84702, #24847, #100400 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.195500757301772937E-05, 4.255218876228979060E-05, 6.203747987203386274E-05, 8.059141772754293306E-05, 9.820314608971937728E-05, 0.0001152776191807706487, 0.0001319156935046207819, 0.0001484884377520183146, 0.0001649906411999995672, 0.0001815288266006448393, 0.0001982728514718028840, 0.0002155459143858949741, 0.0002333293620531217511, 0.0002519771737065587026, 0.0002716049433234985215, 0.0002923416217659442849 ), + .UNSPECIFIED. ) ; +#88374 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58895, #88488, #98077, #49715 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88375 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#88376 = CARTESIAN_POINT ( 'NONE', ( 0.2588557875593014423, -1.022932714501228579, 0.8100000000000001643 ) ) ; +#88377 = EDGE_CURVE ( 'NONE', #94949, #68754, #35925, .T. ) ; +#88378 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88379 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 10.27602300000000035, 0.8648700000000000276 ) ) ; +#88380 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#88381 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49252 ), #70426 ) ; +#88382 = EDGE_CURVE ( 'NONE', #91950, #25241, #16885, .T. ) ; +#88383 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42969 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36804, #19968, #68908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88384 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #62825 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15682, #55044, #42722 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88386 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88385 = SURFACE_SIDE_STYLE ('',( #40935 ) ) ; +#88387 = LINE ( 'NONE', #55746, #57294 ) ; +#88388 = ORIENTED_EDGE ( 'NONE', *, *, #21421, .F. ) ; +#88389 = SURFACE_SIDE_STYLE ('',( #56265 ) ) ; +#88390 = ORIENTED_EDGE ( 'NONE', *, *, #44354, .F. ) ; +#88391 = VECTOR ( 'NONE', #93688, 1000.000000000000000 ) ; +#88392 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88393 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#88394 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88395 = CARTESIAN_POINT ( 'NONE', ( -0.3688379042909170069, -1.119121047813059988, 0.8300000000000000711 ) ) ; +#88396 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88397 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#88398 = FILL_AREA_STYLE_COLOUR ( '', #64587 ) ; +#88399 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18244 ) ) ; +#88400 = VECTOR ( 'NONE', #84905, 1000.000000000000000 ) ; +#88401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88402 = SURFACE_STYLE_FILL_AREA ( #10703 ) ; +#88403 = PLANE ( 'NONE', #96835 ) ; +#88404 = ORIENTED_EDGE ( 'NONE', *, *, #13106, .F. ) ; +#88405 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88406 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88407 = LINE ( 'NONE', #34817, #11276 ) ; +#88408 = EDGE_CURVE ( 'NONE', #58386, #61999, #73993, .T. ) ; +#88409 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28083 ), #81874 ) ; +#88410 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88411 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88413 = ADVANCED_FACE ( 'NONE', ( #91029 ), #36913, .T. ) ; +#88412 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66620, 'distance_accuracy_value', 'NONE'); +#88414 = ORIENTED_EDGE ( 'NONE', *, *, #91813, .T. ) ; +#88415 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#88416 = SURFACE_SIDE_STYLE ('',( #80779 ) ) ; +#88417 = CARTESIAN_POINT ( 'NONE', ( -1.046906373037310045, -0.9912247593444889482, 0.8299999999999999600 ) ) ; +#88418 = FILL_AREA_STYLE ('',( #35340 ) ) ; +#88419 = PLANE ( 'NONE', #58414 ) ; +#88420 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#88421 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88422 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60604 ), #91679 ) ; +#88423 = FACE_OUTER_BOUND ( 'NONE', #42812, .T. ) ; +#88424 = PRESENTATION_STYLE_ASSIGNMENT (( #57307 ) ) ; +#88425 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#88426 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88427 = VERTEX_POINT ( 'NONE', #16914 ) ; +#88428 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88429 = VERTEX_POINT ( 'NONE', #70554 ) ; +#88430 = VECTOR ( 'NONE', #71523, 1000.000000000000000 ) ; +#88431 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71860, 'distance_accuracy_value', 'NONE'); +#88432 = PLANE ( 'NONE', #83893 ) ; +#88433 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#88434 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88435 = CARTESIAN_POINT ( 'NONE', ( 0.5179422451181606712, -1.176801985158418162, 0.8099999999999999423 ) ) ; +#88436 = SURFACE_STYLE_FILL_AREA ( #33324 ) ; +#88437 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8648700000000000276 ) ) ; +#88438 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#88439 = ORIENTED_EDGE ( 'NONE', *, *, #66355, .F. ) ; +#88440 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88441 = LINE ( 'NONE', #50676, #15581 ) ; +#88442 = EDGE_CURVE ( 'NONE', #32201, #97292, #8183, .T. ) ; +#88443 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88444 = ORIENTED_EDGE ( 'NONE', *, *, #10763, .T. ) ; +#88445 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88446 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76992 ) ) ; +#88447 = VERTEX_POINT ( 'NONE', #71070 ) ; +#88448 = FILL_AREA_STYLE_COLOUR ( '', #28865 ) ; +#88449 = VECTOR ( 'NONE', #49150, 1000.000000000000000 ) ; +#88450 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220075051, 2.300000000000000266, -0.02000000000000000042 ) ) ; +#88451 = AXIS2_PLACEMENT_3D ( 'NONE', #10870, #42114, #73266 ) ; +#88452 = FILL_AREA_STYLE ('',( #3190 ) ) ; +#88453 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#88454 = SURFACE_STYLE_FILL_AREA ( #4194 ) ; +#88455 = LINE ( 'NONE', #41014, #15374 ) ; +#88456 = ORIENTED_EDGE ( 'NONE', *, *, #83088, .T. ) ; +#88457 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#88458 = VECTOR ( 'NONE', #483, 1000.000000000000000 ) ; +#88459 = LINE ( 'NONE', #42512, #72363 ) ; +#88460 = ORIENTED_EDGE ( 'NONE', *, *, #27180, .F. ) ; +#88461 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85856, 'distance_accuracy_value', 'NONE'); +#88462 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36296 ), #28131 ) ; +#88463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88464 = VECTOR ( 'NONE', #51505, 1000.000000000000000 ) ; +#88465 = MANIFOLD_SOLID_BREP ( 'ÊäÈë1', #100600 ) ; +#88466 = ORIENTED_EDGE ( 'NONE', *, *, #95693, .T. ) ; +#88467 = FACE_OUTER_BOUND ( 'NONE', #20153, .T. ) ; +#88468 = SURFACE_STYLE_FILL_AREA ( #48679 ) ; +#88469 = CARTESIAN_POINT ( 'NONE', ( 1.753807303740889889, -0.9763607356531520676, 0.8300000000000004041 ) ) ; +#88470 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88471 = CARTESIAN_POINT ( 'NONE', ( 8.383086999999999733, 2.877107000000000081, 0.8991599999999999593 ) ) ; +#88472 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88473 = LINE ( 'NONE', #3703, #2095 ) ; +#88474 = FACE_OUTER_BOUND ( 'NONE', #55369, .T. ) ; +#88475 = VERTEX_POINT ( 'NONE', #62934 ) ; +#88477 = ORIENTED_EDGE ( 'NONE', *, *, #41232, .T. ) ; +#88476 = ORIENTED_EDGE ( 'NONE', *, *, #84383, .F. ) ; +#88478 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.100000000000000089, -0.02000000000000280026 ) ) ; +#88479 = ORIENTED_EDGE ( 'NONE', *, *, #91807, .T. ) ; +#88480 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.183333333333333570, 0.000000000000000000 ) ) ; +#88481 = VECTOR ( 'NONE', #69043, 1000.000000000000114 ) ; +#88482 = AXIS2_PLACEMENT_3D ( 'NONE', #27616, #66886, #21430 ) ; +#88483 = EDGE_LOOP ( 'NONE', ( #89617, #53149, #39361, #63445 ) ) ; +#88484 = ORIENTED_EDGE ( 'NONE', *, *, #83786, .T. ) ; +#88485 = ADVANCED_FACE ( 'NONE', ( #1117 ), #71583, .T. ) ; +#88487 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88486 = FILL_AREA_STYLE_COLOUR ( '', #80390 ) ; +#88488 = CARTESIAN_POINT ( 'NONE', ( 1.016666666666667052, 3.099999999999980549, 0.000000000000000000 ) ) ; +#88489 = FACE_OUTER_BOUND ( 'NONE', #42309, .T. ) ; +#88490 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54234 ), #6829 ) ; +#88491 = ORIENTED_EDGE ( 'NONE', *, *, #37962, .T. ) ; +#88492 = SURFACE_SIDE_STYLE ('',( #56878 ) ) ; +#88493 = SURFACE_STYLE_FILL_AREA ( #18532 ) ; +#88494 = FACE_OUTER_BOUND ( 'NONE', #59612, .T. ) ; +#88495 = ORIENTED_EDGE ( 'NONE', *, *, #21631, .T. ) ; +#88496 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #45130, #60020, #22183, #82975 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88497 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000002037, 0.2500000000000000000 ) ) ; +#88498 = SURFACE_SIDE_STYLE ('',( #18538 ) ) ; +#88499 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25814 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20580, #67051, #27780 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88500 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#88501 = VECTOR ( 'NONE', #2929, 1000.000000000000114 ) ; +#88502 = CARTESIAN_POINT ( 'NONE', ( -1.429289321881345165, 0.7099999999999999645, 0.8000000000000003775 ) ) ; +#88503 = CARTESIAN_POINT ( 'NONE', ( 0.04622384033856599683, -1.137681993439920047, 0.8300000000000002931 ) ) ; +#88504 = ADVANCED_FACE ( 'NONE', ( #14879 ), #1642, .F. ) ; +#88506 = FILL_AREA_STYLE_COLOUR ( '', #75897 ) ; +#88505 = SURFACE_STYLE_FILL_AREA ( #40034 ) ; +#88507 = FILL_AREA_STYLE_COLOUR ( '', #48385 ) ; +#88508 = DIRECTION ( 'NONE', ( -0.9361199317767866512, 0.000000000000000000, -0.3516809254569038812 ) ) ; +#88509 = SURFACE_STYLE_USAGE ( .BOTH. , #88004 ) ; +#88510 = STYLED_ITEM ( 'NONE', ( #49132 ), #35834 ) ; +#88511 = CARTESIAN_POINT ( 'NONE', ( 1.059875661710510064, -1.061634207873779934, 0.8300000000000022915 ) ) ; +#88512 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#88513 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88514 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88515 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13376 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27440, #19248, #58609 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88516 = CARTESIAN_POINT ( 'NONE', ( 1.117494933574350036, -0.8946064028769500354, 0.8299999999999999600 ) ) ; +#88517 = EDGE_LOOP ( 'NONE', ( #14796, #20766, #35130, #93976 ) ) ; +#88518 = FACE_OUTER_BOUND ( 'NONE', #11388, .T. ) ; +#88519 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62521 ), #67376 ) ; +#88520 = PRESENTATION_STYLE_ASSIGNMENT (( #26255 ) ) ; +#88522 = VECTOR ( 'NONE', #70982, 1000.000000000000000 ) ; +#88521 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#88523 = LINE ( 'NONE', #52131, #51012 ) ; +#88524 = AXIS2_PLACEMENT_3D ( 'NONE', #11241, #27189, #42492 ) ; +#88525 = FILL_AREA_STYLE_COLOUR ( '', #89075 ) ; +#88526 = ORIENTED_EDGE ( 'NONE', *, *, #52708, .F. ) ; +#88527 = ADVANCED_FACE ( 'NONE', ( #67289 ), #10704, .F. ) ; +#88528 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88529 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#88531 = VECTOR ( 'NONE', #28582, 1000.000000000000000 ) ; +#88530 = SURFACE_STYLE_FILL_AREA ( #26265 ) ; +#88532 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55981 ) ) ; +#88533 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#88534 = SURFACE_STYLE_FILL_AREA ( #57413 ) ; +#88535 = SURFACE_SIDE_STYLE ('',( #55908 ) ) ; +#88536 = ADVANCED_FACE ( 'NONE', ( #3140 ), #88403, .F. ) ; +#88537 = EDGE_LOOP ( 'NONE', ( #80220, #65977, #30147, #77199, #3791, #38946, #78169, #21910 ) ) ; +#88538 = LINE ( 'NONE', #19074, #24537 ) ; +#88539 = FILL_AREA_STYLE_COLOUR ( '', #82067 ) ; +#88540 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.699999999999999956, -0.02000000000000419845 ) ) ; +#88541 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#88542 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.8499999999999999778, 0.000000000000000000 ) ) ; +#88543 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16706 ), #75491 ) ; +#88544 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88545 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88546 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88547 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88548 = FACE_OUTER_BOUND ( 'NONE', #17043, .T. ) ; +#88549 = SURFACE_STYLE_FILL_AREA ( #72727 ) ; +#88550 = ORIENTED_EDGE ( 'NONE', *, *, #50762, .F. ) ; +#88551 = VECTOR ( 'NONE', #3503, 1000.000000000000000 ) ; +#88552 = VERTEX_POINT ( 'NONE', #33799 ) ; +#88553 = LINE ( 'NONE', #14911, #25789 ) ; +#88554 = CARTESIAN_POINT ( 'NONE', ( 0.1831366936980619864, -1.373561790606270039, 0.8100000000000000533 ) ) ; +#88555 = FACE_OUTER_BOUND ( 'NONE', #96092, .T. ) ; +#88556 = SURFACE_SIDE_STYLE ('',( #25303 ) ) ; +#88557 = ORIENTED_EDGE ( 'NONE', *, *, #9608, .F. ) ; +#88558 = ADVANCED_FACE ( 'NONE', ( #91283 ), #29984, .T. ) ; +#88559 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88560 = CIRCLE ( 'NONE', #73919, 0.01000000000000002623 ) ; +#88561 = PLANE ( 'NONE', #68281 ) ; +#88562 = ORIENTED_EDGE ( 'NONE', *, *, #15112, .T. ) ; +#88563 = LINE ( 'NONE', #18083, #91760 ) ; +#88564 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86976 ) ) ; +#88565 = SURFACE_STYLE_FILL_AREA ( #96701 ) ; +#88566 = SURFACE_SIDE_STYLE ('',( #26818 ) ) ; +#88567 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 1.355252715606880049E-16 ) ) ; +#88568 = STYLED_ITEM ( 'NONE', ( #55387 ), #76006 ) ; +#88569 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01500000000000000118, -0.1458578643762691029 ) ) ; +#88570 = ORIENTED_EDGE ( 'NONE', *, *, #63372, .F. ) ; +#88571 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#88572 = PLANE ( 'NONE', #16266 ) ; +#88573 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11925, 'distance_accuracy_value', 'NONE'); +#88574 = FACE_OUTER_BOUND ( 'NONE', #1350, .T. ) ; +#88575 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64574 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58081, #4889, #90688 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88576 = LINE ( 'NONE', #95202, #19320 ) ; +#88577 = ADVANCED_FACE ( 'NONE', ( #39168 ), #68290, .T. ) ; +#88578 = VERTEX_POINT ( 'NONE', #60667 ) ; +#88579 = EDGE_CURVE ( 'NONE', #26091, #38992, #30006, .T. ) ; +#88580 = VECTOR ( 'NONE', #27841, 1000.000000000000000 ) ; +#88581 = VECTOR ( 'NONE', #70416, 1000.000000000000000 ) ; +#88583 = STYLED_ITEM ( 'NONE', ( #68291 ), #35167 ) ; +#88582 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #6836, #84044, #69168, #14547 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88584 = SURFACE_STYLE_USAGE ( .BOTH. , #41136 ) ; +#88585 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88586 = PRESENTATION_STYLE_ASSIGNMENT (( #12406 ) ) ; +#88587 = CARTESIAN_POINT ( 'NONE', ( -1.240990607961793835, -1.203341844243227099, 0.8099999999998384048 ) ) ; +#88588 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88589 = CIRCLE ( 'NONE', #47857, 0.04999999999999991257 ) ; +#88590 = VECTOR ( 'NONE', #77854, 1000.000000000000000 ) ; +#88591 = EDGE_LOOP ( 'NONE', ( #74152, #48450, #62453, #100181, #12705, #63661, #95150, #31681, #56089, #13572, #33753, #57008, #8265, #20752, #48540, #79664, #48095, #43595, #28667, #50082, #56871, #83121, #66609, #54812, #77655, #66977, #38372, #57632, #94300, #2202, #26703, #70136, #22681, #47010, #41322, #98021, #11375, #88207, #3084, #41107, #41402, #83157, #24493, #2691, #26774, #79311, #49144, #14205, #37392, #99593, #77714, #62365, #54804, #62904, #83947, #43023, #97563, #35911, #10153, #18129, #26575, #70360, #82325, #79721, #88439, #37047, #38642, #71372, #91249, #72396, #96545, #65146, #83722, #98310, #13258, #61787, #37637, #7748, #54944, #5543, #2982, #38842, #55715, #4477, #86400, #42988, #50336, #81848, #14465, #14562, #98382, #81592, #97492, #17242, #68375, #84822, #85455, #56523, #15857, #7160, #94649, #95321, #14300, #63507, #61278, #35829, #29122, #72166, #24951, #85801, #30930, #22770, #83999, #52452, #22046, #16643, #39298, #91817, #9156, #36243, #86614, #67962, #66330, #25370, #81309, #100175, #16978, #32122, #51235, #79716, #63983, #100021, #18653, #87990, #3338, #71905, #69739, #27006, #52309, #22659, #77745, #35770, #99181, #89731, #70494, #27805, #82700, #67713, #67627, #27861, #88404, #87727, #72892, #99376, #62650, #59467, #4469, #82271, #43907, #99531, #22561, #5144, #45060, #96683, #88259, #31852, #29546, #67441, #73706, #61966, #32681, #1310, #93222, #73767, #29689, #100271, #47233, #74160, #8775, #96072, #30165, #22159, #29576, #14811, #40312, #82479, #88696, #67845, #10285, #32126, #51078, #89111, #20376, #53209, #43817, #78549, #83235, #79743, #100121, #51069, #67324, #25394, #5766, #75674, #68222, #60525, #62563, #23176, #79968, #68186, #94683, #63013, #65320, #21250, #15614, #49473, #61827, #50311, #3447, #69791, #89733, #38220, #77416, #56359, #35038, #69092, #34220, #25104, #19783, #86981, #96107, #10877, #94946, #70978, #32564, #32427, #8497, #91107, #80202, #78052, #22431, #50402, #66747, #95092, #83344, #62280, #53570, #77626, #46507, #89740, #67107, #71654, #40261, #38489, #21251, #14717, #24876, #43723, #79566, #2763, #48083, #88757, #91723, #8261, #76213, #6444, #63411, #59124, #94568, #84359, #43451, #9129, #99222, #64858, #37373, #15232, #94088, #35884, #94471, #49224, #50720, #69930, #95569, #56242, #59786, #71796, #43787, #62656, #27882, #91509, #70911, #71937, #1576, #42081, #97599, #37837, #43980, #97813, #63621, #91636, #32583, #15090, #60728, #44507, #37965, #38431, #11129, #30650, #71537, #84115, #99430, #73154, #86345, #90841, #14605, #77015, #50849, #17144, #74791, #25214, #28097, #65779, #100143, #72618, #63975, #96626, #99517, #85986, #22082, #14600, #73088, #28041, #86328, #987, #83584, #33312, #9246, #19124, #85955, #98057 ) ) ; +#88593 = VERTEX_POINT ( 'NONE', #54522 ) ; +#88592 = CARTESIAN_POINT ( 'NONE', ( 3.843461000000000460, 5.422691000000000372, 0.8648700000000000276 ) ) ; +#88594 = EDGE_CURVE ( 'NONE', #35425, #18587, #15659, .T. ) ; +#88595 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #66380, 'distance_accuracy_value', 'NONE'); +#88596 = AXIS2_PLACEMENT_3D ( 'NONE', #84085, #75924, #28960 ) ; +#88597 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#88598 = SURFACE_STYLE_FILL_AREA ( #81486 ) ; +#88599 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88600 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88601 = ORIENTED_EDGE ( 'NONE', *, *, #87616, .F. ) ; +#88602 = SURFACE_STYLE_USAGE ( .BOTH. , #97246 ) ; +#88603 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88604 = CYLINDRICAL_SURFACE ( 'NONE', #45007, 0.05000000000000002359 ) ; +#88605 = CIRCLE ( 'NONE', #29918, 0.01000000000000002623 ) ; +#88606 = ORIENTED_EDGE ( 'NONE', *, *, #26542, .F. ) ; +#88608 = CARTESIAN_POINT ( 'NONE', ( 1.693587662337660005, -1.445454545454550210, 0.8199999999999999512 ) ) ; +#88607 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#88609 = VERTEX_POINT ( 'NONE', #52495 ) ; +#88610 = ORIENTED_EDGE ( 'NONE', *, *, #45224, .T. ) ; +#88611 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#88612 = ADVANCED_FACE ( 'NONE', ( #21845, #53006, #75970, #13605 ), #37190, .F. ) ; +#88613 = SURFACE_STYLE_FILL_AREA ( #11926 ) ; +#88614 = PLANE ( 'NONE', #45614 ) ; +#88615 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88616 = VERTEX_POINT ( 'NONE', #17186 ) ; +#88617 = ORIENTED_EDGE ( 'NONE', *, *, #86467, .T. ) ; +#88618 = SURFACE_STYLE_USAGE ( .BOTH. , #17150 ) ; +#88619 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55191 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61482, #68590, #76260 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88621 = ORIENTED_EDGE ( 'NONE', *, *, #8726, .F. ) ; +#88620 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_R0201_20210301.STEP', ( #9417, #86081 ), #29031 ) ; +#88622 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88624 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88623 = SURFACE_SIDE_STYLE ('',( #59037 ) ) ; +#88625 = CARTESIAN_POINT ( 'NONE', ( -1.367649144690350038, -1.097307480365639965, 0.8299999999999999600 ) ) ; +#88626 = MANIFOLD_SOLID_BREP ( 'ÊäÈë65', #40341 ) ; +#88627 = SURFACE_SIDE_STYLE ('',( #33530 ) ) ; +#88628 = VECTOR ( 'NONE', #11822, 1000.000000000000000 ) ; +#88629 = CARTESIAN_POINT ( 'NONE', ( 1.901298701298699934, -1.329788961038959938, 0.8199999999999999512 ) ) ; +#88630 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88631 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16657, #39677, #88166, #86131 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 8.364153930971524925E-15, 7.071456405688010256E-05 ), + .UNSPECIFIED. ) ; +#88633 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#88632 = SURFACE_SIDE_STYLE ('',( #96271 ) ) ; +#88634 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#88635 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#88636 = SURFACE_STYLE_USAGE ( .BOTH. , #3868 ) ; +#88637 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#88638 = VERTEX_POINT ( 'NONE', #9468 ) ; +#88639 = EDGE_CURVE ( 'NONE', #74432, #5416, #64678, .T. ) ; +#88640 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.750000000000000000, -0.02000000000000000042 ) ) ; +#88641 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29941 ), #49521 ) ; +#88642 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88643 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29269, 'distance_accuracy_value', 'NONE'); +#88644 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#88645 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#88646 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13568 ), #23419 ) ; +#88647 = CARTESIAN_POINT ( 'NONE', ( -1.900000000000000133, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#88648 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88649 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88650 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#88651 = SURFACE_STYLE_FILL_AREA ( #26891 ) ; +#88652 = EDGE_CURVE ( 'NONE', #84102, #51520, #88631, .T. ) ; +#88653 = VERTEX_POINT ( 'NONE', #70820 ) ; +#88654 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, -3.500000000000000444, 0.000000000000000000 ) ) ; +#88655 = SURFACE_STYLE_FILL_AREA ( #57549 ) ; +#88658 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88657 = STYLED_ITEM ( 'NONE', ( #96603 ), #37980 ) ; +#88656 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88659 = PRESENTATION_STYLE_ASSIGNMENT (( #81547 ) ) ; +#88660 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42106 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35068, #4388, #43684 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88661 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660229, -1.070941558441560026, 0.8299999999999999600 ) ) ; +#88662 = FILL_AREA_STYLE_COLOUR ( '', #23657 ) ; +#88663 = FILL_AREA_STYLE ('',( #54649 ) ) ; +#88665 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88664 = AXIS2_PLACEMENT_3D ( 'NONE', #83993, #13988, #46147 ) ; +#88666 = LINE ( 'NONE', #82528, #10274 ) ; +#88667 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #603 ) ) ; +#88668 = SURFACE_STYLE_USAGE ( .BOTH. , #57560 ) ; +#88669 = PLANE ( 'NONE', #92964 ) ; +#88670 = FILL_AREA_STYLE_COLOUR ( '', #5993 ) ; +#88671 = SURFACE_SIDE_STYLE ('',( #9966 ) ) ; +#88672 = FILL_AREA_STYLE ('',( #41226 ) ) ; +#88673 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45922 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45048, #92030, #100089 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88674 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88675 = STYLED_ITEM ( 'NONE', ( #23203 ), #11839 ) ; +#88676 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#88677 = LINE ( 'NONE', #11485, #1438 ) ; +#88678 = ORIENTED_EDGE ( 'NONE', *, *, #38983, .F. ) ; +#88679 = SURFACE_STYLE_FILL_AREA ( #72346 ) ; +#88680 = PRESENTATION_STYLE_ASSIGNMENT (( #11491 ) ) ; +#88682 = DIRECTION ( 'NONE', ( 0.7974221540510221251, -0.6034218327410999505, 0.000000000000000000 ) ) ; +#88681 = SURFACE_STYLE_USAGE ( .BOTH. , #20233 ) ; +#88683 = SURFACE_STYLE_USAGE ( .BOTH. , #71875 ) ; +#88684 = AXIS2_PLACEMENT_3D ( 'NONE', #31208, #54194, #551 ) ; +#88685 = ADVANCED_FACE ( 'NONE', ( #47848 ), #873, .T. ) ; +#88686 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999334, 0.000000000000000000 ) ) ; +#88687 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#88688 = ORIENTED_EDGE ( 'NONE', *, *, #48920, .F. ) ; +#88689 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88690 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.6999999999999999556, -0.02000000000000000042 ) ) ; +#88691 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#88692 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#88693 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58124 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4198, #11264, #18994 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88694 = PRESENTATION_STYLE_ASSIGNMENT (( #26428 ) ) ; +#88695 = ADVANCED_FACE ( 'NONE', ( #43188 ), #65680, .F. ) ; +#88696 = ORIENTED_EDGE ( 'NONE', *, *, #24737, .F. ) ; +#88697 = EDGE_LOOP ( 'NONE', ( #75054, #84955, #10156, #25943 ) ) ; +#88698 = ADVANCED_FACE ( 'NONE', ( #96789 ), #67175, .T. ) ; +#88699 = VECTOR ( 'NONE', #29137, 1000.000000000000000 ) ; +#88700 = SURFACE_STYLE_FILL_AREA ( #49409 ) ; +#88701 = CARTESIAN_POINT ( 'NONE', ( -1.144540609093224859, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#88702 = EDGE_LOOP ( 'NONE', ( #28970, #48770, #37000, #16576 ) ) ; +#88703 = CARTESIAN_POINT ( 'NONE', ( 1.711221411465380093, -1.219829592979950084, 0.8100000000000000533 ) ) ; +#88704 = EDGE_CURVE ( 'NONE', #56713, #60423, #42215, .T. ) ; +#88705 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#88706 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88707 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#88708 = PLANE ( 'NONE', #72580 ) ; +#88709 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#88710 = PRODUCT_CONTEXT ( 'NONE', #38474, 'mechanical' ) ; +#88711 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #50255, #12843, #11815, #82866 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88713 = VERTEX_POINT ( 'NONE', #26895 ) ; +#88712 = EDGE_LOOP ( 'NONE', ( #47319, #40763, #49171, #46782 ) ) ; +#88714 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64589 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60546, #52865, #68652 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88715 = ORIENTED_EDGE ( 'NONE', *, *, #3206, .T. ) ; +#88716 = EDGE_CURVE ( 'NONE', #53981, #65434, #58064, .T. ) ; +#88717 = VECTOR ( 'NONE', #71052, 1000.000000000000000 ) ; +#88718 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91472, 'distance_accuracy_value', 'NONE'); +#88719 = CARTESIAN_POINT ( 'NONE', ( 1.897517923509739912, -1.370875895369189967, 0.8100000000000000533 ) ) ; +#88721 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#88720 = CARTESIAN_POINT ( 'NONE', ( 0.5232566677822769741, -0.9829422030519651132, 0.8299999999999999600 ) ) ; +#88722 = ORIENTED_EDGE ( 'NONE', *, *, #27662, .T. ) ; +#88723 = AXIS2_PLACEMENT_3D ( 'NONE', #62576, #32921, #93135 ) ; +#88724 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#88725 = EDGE_CURVE ( 'NONE', #43154, #25637, #89169, .T. ) ; +#88726 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.300000000000000266, 0.1829999999999580296 ) ) ; +#88728 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57804 ), #15366 ) ; +#88727 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63476 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #48047, #100512, #77156 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88729 = STYLED_ITEM ( 'NONE', ( #38310 ), #98176 ) ; +#88730 = ORIENTED_EDGE ( 'NONE', *, *, #15583, .T. ) ; +#88731 = ORIENTED_EDGE ( 'NONE', *, *, #40773, .T. ) ; +#88732 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#88733 = STYLED_ITEM ( 'NONE', ( #49860 ), #60946 ) ; +#88734 = ORIENTED_EDGE ( 'NONE', *, *, #37021, .T. ) ; +#88735 = ORIENTED_EDGE ( 'NONE', *, *, #5103, .T. ) ; +#88736 = LINE ( 'NONE', #3970, #55944 ) ; +#88737 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80597 ), #20283 ) ; +#88738 = EDGE_CURVE ( 'NONE', #60603, #44243, #27910, .T. ) ; +#88740 = LINE ( 'NONE', #66271, #2603 ) ; +#88739 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.350000000000000089, 0.000000000000000000 ) ) ; +#88741 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#88742 = EDGE_CURVE ( 'NONE', #45932, #25243, #11965, .T. ) ; +#88743 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88745 = ORIENTED_EDGE ( 'NONE', *, *, #30114, .T. ) ; +#88744 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 0.4333333333333323489, 0.000000000000000000 ) ) ; +#88746 = FILL_AREA_STYLE ('',( #18775 ) ) ; +#88747 = VERTEX_POINT ( 'NONE', #44186 ) ; +#88748 = ADVANCED_FACE ( 'NONE', ( #68164 ), #76845, .T. ) ; +#88749 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88750 = CARTESIAN_POINT ( 'NONE', ( -0.2957352054868390145, -1.084890943604200020, 0.8299999999999999600 ) ) ; +#88751 = FILL_AREA_STYLE_COLOUR ( '', #13018 ) ; +#88752 = ORIENTED_EDGE ( 'NONE', *, *, #77872, .F. ) ; +#88754 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88753 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88755 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31677 ) ) ; +#88756 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88757 = ORIENTED_EDGE ( 'NONE', *, *, #11659, .F. ) ; +#88758 = ORIENTED_EDGE ( 'NONE', *, *, #78867, .T. ) ; +#88760 = FILL_AREA_STYLE ('',( #41312 ) ) ; +#88759 = PRODUCT_DEFINITION ( 'δ֪', '', #40516, #88192 ) ; +#88761 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5500000000000000444, -0.02000000000000000042 ) ) ; +#88762 = AXIS2_PLACEMENT_3D ( 'NONE', #33481, #34497, #17611 ) ; +#88763 = SURFACE_STYLE_FILL_AREA ( #65794 ) ; +#88764 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5558 ), #96820 ) ; +#88765 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#88766 = SURFACE_STYLE_USAGE ( .BOTH. , #89758 ) ; +#88767 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999960032, -0.9000000000000001332, 0.1829999999999619986 ) ) ; +#88768 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58691, 'distance_accuracy_value', 'NONE'); +#88769 = ORIENTED_EDGE ( 'NONE', *, *, #83288, .F. ) ; +#88770 = EDGE_CURVE ( 'NONE', #22523, #60973, #57030, .T. ) ; +#88771 = CARTESIAN_POINT ( 'NONE', ( 0.04300883857482180189, -1.212495751768609908, 0.8299999999999999600 ) ) ; +#88772 = ORIENTED_EDGE ( 'NONE', *, *, #76188, .F. ) ; +#88773 = AXIS2_PLACEMENT_3D ( 'NONE', #35178, #28985, #50995 ) ; +#88774 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#88775 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88776 = CARTESIAN_POINT ( 'NONE', ( 1.381901993660050065, -1.214210613447320064, 0.8299999999999999600 ) ) ; +#88777 = LINE ( 'NONE', #66301, #90389 ) ; +#88778 = FILL_AREA_STYLE_COLOUR ( '', #19333 ) ; +#88779 = FILL_AREA_STYLE_COLOUR ( '', #29158 ) ; +#88780 = PLANE ( 'NONE', #53226 ) ; +#88781 = FILL_AREA_STYLE_COLOUR ( '', #70491 ) ; +#88782 = EDGE_CURVE ( 'NONE', #35668, #66436, #87364, .T. ) ; +#88783 = ORIENTED_EDGE ( 'NONE', *, *, #27751, .T. ) ; +#88784 = PLANE ( 'NONE', #18314 ) ; +#88785 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88786 = AXIS2_PLACEMENT_3D ( 'NONE', #12472, #66184, #11459 ) ; +#88787 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#88788 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88789 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#88790 = EDGE_CURVE ( 'NONE', #12510, #71293, #6338, .T. ) ; +#88791 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74067 ), #46328 ) ; +#88792 = LINE ( 'NONE', #41339, #58204 ) ; +#88793 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88794 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88795 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.499999999999980016, 0.1829999999999999960 ) ) ; +#88796 = VECTOR ( 'NONE', #60786, 1000.000000000000000 ) ; +#88798 = ORIENTED_EDGE ( 'NONE', *, *, #16748, .F. ) ; +#88797 = VECTOR ( 'NONE', #96050, 1000.000000000000000 ) ; +#88799 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88800 = FACE_OUTER_BOUND ( 'NONE', #74154, .T. ) ; +#88801 = FILL_AREA_STYLE_COLOUR ( '', #80168 ) ; +#88802 = MANIFOLD_SOLID_BREP ( 'ÊäÈë101', #92607 ) ; +#88803 = ORIENTED_EDGE ( 'NONE', *, *, #88652, .T. ) ; +#88804 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.600000000000000089, -12.44500000000000028 ) ) ; +#88805 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88806 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#88807 = CARTESIAN_POINT ( 'NONE', ( 1.733257866282789994, -0.9021709523542820186, 0.8299999999999999600 ) ) ; +#88808 = VECTOR ( 'NONE', #37509, 1000.000000000000000 ) ; +#88809 = VECTOR ( 'NONE', #75470, 1000.000000000000000 ) ; +#88810 = SURFACE_SIDE_STYLE ('',( #27045 ) ) ; +#88812 = CARTESIAN_POINT ( 'NONE', ( 1.788364155591039895, -1.009819306370540071, 0.8100000000000006084 ) ) ; +#88811 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39743 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55158, #86250, #22460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88813 = EDGE_CURVE ( 'NONE', #84669, #1063, #21217, .T. ) ; +#88814 = CIRCLE ( 'NONE', #57892, 0.009999999999999998473 ) ; +#88815 = SURFACE_STYLE_USAGE ( .BOTH. , #33185 ) ; +#88816 = VERTEX_POINT ( 'NONE', #5850 ) ; +#88817 = ORIENTED_EDGE ( 'NONE', *, *, #85954, .T. ) ; +#88818 = PLANE ( 'NONE', #91134 ) ; +#88819 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6375, 'distance_accuracy_value', 'NONE'); +#88820 = SURFACE_STYLE_USAGE ( .BOTH. , #57717 ) ; +#88821 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#88822 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71243 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76065, #76560, #6560 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88823 = SURFACE_STYLE_FILL_AREA ( #18344 ) ; +#88824 = FILL_AREA_STYLE_COLOUR ( '', #72915 ) ; +#88825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88826 = DIRECTION ( 'NONE', ( 0.7071071146859688739, 0.7071064476869688420, 0.000000000000000000 ) ) ; +#88827 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88828 = VERTEX_POINT ( 'NONE', #76332 ) ; +#88829 = EDGE_CURVE ( 'NONE', #8086, #65783, #37067, .T. ) ; +#88830 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19623, #66097, #17714, #67082 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#88831 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#88832 = ORIENTED_EDGE ( 'NONE', *, *, #50081, .F. ) ; +#88833 = CARTESIAN_POINT ( 'NONE', ( -0.1759195832032370010, -1.500900992704750081, 0.8299999999999999600 ) ) ; +#88834 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88835 = EDGE_CURVE ( 'NONE', #4845, #37993, #29867, .T. ) ; +#88836 = PRESENTATION_STYLE_ASSIGNMENT (( #9133 ) ) ; +#88837 = FILL_AREA_STYLE ('',( #83200 ) ) ; +#88838 = CARTESIAN_POINT ( 'NONE', ( -1.077884384038320098, -0.9706035140527139449, 0.8299999999999999600 ) ) ; +#88839 = FILL_AREA_STYLE_COLOUR ( '', #42043 ) ; +#88840 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88841 = FILL_AREA_STYLE ('',( #2078 ) ) ; +#88844 = ORIENTED_EDGE ( 'NONE', *, *, #12589, .F. ) ; +#88843 = ORIENTED_EDGE ( 'NONE', *, *, #15275, .T. ) ; +#88842 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94303 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34558, #1881, #57039 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88845 = SURFACE_SIDE_STYLE ('',( #34748 ) ) ; +#88846 = VERTEX_POINT ( 'NONE', #41091 ) ; +#88847 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88848 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #25256 ), #82307 ) ; +#88850 = SURFACE_SIDE_STYLE ('',( #81215 ) ) ; +#88849 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.966666666666666785, 0.000000000000000000 ) ) ; +#88851 = ORIENTED_EDGE ( 'NONE', *, *, #49009, .F. ) ; +#88852 = ORIENTED_EDGE ( 'NONE', *, *, #99441, .F. ) ; +#88853 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88854 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -11.57000000000000028 ) ) ; +#88855 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#88856 = VECTOR ( 'NONE', #73850, 1000.000000000000000 ) ; +#88857 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88858 = LINE ( 'NONE', #20403, #87812 ) ; +#88859 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.5000000000000000000, -12.64499999999999957 ) ) ; +#88860 = VERTEX_POINT ( 'NONE', #8321 ) ; +#88861 = ORIENTED_EDGE ( 'NONE', *, *, #69145, .T. ) ; +#88862 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92335 ) ) ; +#88863 = AXIS2_PLACEMENT_3D ( 'NONE', #42373, #82669, #58713 ) ; +#88864 = AXIS2_PLACEMENT_3D ( 'NONE', #77687, #79209, #70525 ) ; +#88865 = FILL_AREA_STYLE_COLOUR ( '', #69774 ) ; +#88866 = ORIENTED_EDGE ( 'NONE', *, *, #57857, .F. ) ; +#88867 = FACE_OUTER_BOUND ( 'NONE', #68974, .T. ) ; +#88868 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#88869 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26928 ), #75807 ) ; +#88870 = ADVANCED_FACE ( 'NONE', ( #16541 ), #7817, .F. ) ; +#88871 = VERTEX_POINT ( 'NONE', #746 ) ; +#88872 = FACE_OUTER_BOUND ( 'NONE', #6918, .T. ) ; +#88873 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88874 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88875 = ORIENTED_EDGE ( 'NONE', *, *, #98495, .F. ) ; +#88877 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88876 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34970 ) ) ; +#88878 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -8.179221189230645204E-17, -0.6500000000000001332 ) ) ; +#88879 = ORIENTED_EDGE ( 'NONE', *, *, #22569, .F. ) ; +#88880 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#88881 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#88883 = AXIS2_PLACEMENT_3D ( 'NONE', #26873, #17658, #56527 ) ; +#88882 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #48130 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3226, #90489, #26223 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88884 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88885 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87266 ) ) ; +#88886 = CARTESIAN_POINT ( 'NONE', ( -0.1439069218330049915, -1.121518536532789989, 0.8299999999999999600 ) ) ; +#88887 = CARTESIAN_POINT ( 'NONE', ( -0.9931616945682509856, -1.308270162923429902, 0.8300000000000000711 ) ) ; +#88888 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#88889 = STYLED_ITEM ( 'NONE', ( #13462 ), #98000 ) ; +#88890 = FACE_OUTER_BOUND ( 'NONE', #36884, .T. ) ; +#88891 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.000000000000000000, 0.1400000000000000133 ) ) ; +#88893 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88892 = LINE ( 'NONE', #18921, #52978 ) ; +#88894 = VERTEX_POINT ( 'NONE', #56431 ) ; +#88895 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#88896 = ADVANCED_FACE ( 'NONE', ( #25769 ), #95664, .F. ) ; +#88897 = CARTESIAN_POINT ( 'NONE', ( 1.823253843827010057, -1.327673353236110243, 0.8099999999999996092 ) ) ; +#88898 = ORIENTED_EDGE ( 'NONE', *, *, #681, .F. ) ; +#88899 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56269 ) ) ; +#88900 = FILL_AREA_STYLE_COLOUR ( '', #84390 ) ; +#88901 = PRESENTATION_STYLE_ASSIGNMENT (( #57790 ) ) ; +#88902 = CARTESIAN_POINT ( 'NONE', ( -0.1199320083468070064, -1.507611749840819915, 0.8299999999999999600 ) ) ; +#88904 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67647 ) ) ; +#88903 = CARTESIAN_POINT ( 'NONE', ( -0.5075789211564899484, -1.256245978568790056, 0.8300000000000000711 ) ) ; +#88905 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4750000000000000333, 0.2500000000000000000 ) ) ; +#88907 = PRESENTATION_STYLE_ASSIGNMENT (( #4132 ) ) ; +#88906 = CARTESIAN_POINT ( 'NONE', ( 1.150000000000000133, 0.6892893218813450629, -1.100000000000000089 ) ) ; +#88908 = FILL_AREA_STYLE_COLOUR ( '', #71187 ) ; +#88909 = ADVANCED_FACE ( 'NONE', ( #48754 ), #47213, .F. ) ; +#88910 = LINE ( 'NONE', #27145, #75210 ) ; +#88911 = VECTOR ( 'NONE', #84349, 1000.000000000000000 ) ; +#88912 = PRESENTATION_STYLE_ASSIGNMENT (( #36186 ) ) ; +#88913 = ORIENTED_EDGE ( 'NONE', *, *, #12556, .T. ) ; +#88914 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#88915 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #56287 ), #97033 ) ; +#88916 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24930 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10658, #59272, #81731 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#88917 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#88918 = EDGE_CURVE ( 'NONE', #59654, #92602, #51255, .T. ) ; +#88919 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, 0.000000000000000000 ) ) ; +#88920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62846 ) ) ; +#88921 = EDGE_CURVE ( 'NONE', #43736, #12201, #98128, .T. ) ; +#88922 = ORIENTED_EDGE ( 'NONE', *, *, #98164, .F. ) ; +#88923 = STYLED_ITEM ( 'NONE', ( #89106 ), #49580 ) ; +#88924 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88925 = FACE_OUTER_BOUND ( 'NONE', #19684, .T. ) ; +#88926 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96980 ), #38350 ) ; +#88927 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7277 ), #64440 ) ; +#88928 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#88929 = LINE ( 'NONE', #10201, #2935 ) ; +#88931 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#88930 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#88932 = SURFACE_STYLE_FILL_AREA ( #50655 ) ; +#88933 = VECTOR ( 'NONE', #44715, 1000.000000000000000 ) ; +#88934 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84049 ) ) ; +#88935 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#88937 = EDGE_CURVE ( 'NONE', #64865, #62517, #50281, .T. ) ; +#88936 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #30055 ) ; +#88938 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76406, 'distance_accuracy_value', 'NONE'); +#88939 = EDGE_CURVE ( 'NONE', #828, #54630, #11347, .T. ) ; +#88940 = VERTEX_POINT ( 'NONE', #41587 ) ; +#88941 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88942 = ORIENTED_EDGE ( 'NONE', *, *, #76397, .T. ) ; +#88943 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88944 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63074, 'distance_accuracy_value', 'NONE'); +#88945 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62882, 'distance_accuracy_value', 'NONE'); +#88946 = ADVANCED_FACE ( 'NONE', ( #19591 ), #81902, .T. ) ; +#88947 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#88948 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#88949 = SURFACE_STYLE_FILL_AREA ( #64957 ) ; +#88950 = AXIS2_PLACEMENT_3D ( 'NONE', #61335, #22487, #53648 ) ; +#88951 = CARTESIAN_POINT ( 'NONE', ( 0.5854301948051943150, 0.6899999999999999467, 0.2077922077922078614 ) ) ; +#88952 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88953 = VERTEX_POINT ( 'NONE', #80395 ) ; +#88954 = SURFACE_STYLE_FILL_AREA ( #19500 ) ; +#88955 = PLANE ( 'NONE', #89568 ) ; +#88957 = AXIS2_PLACEMENT_3D ( 'NONE', #57277, #72559, #18932 ) ; +#88956 = STYLED_ITEM ( 'NONE', ( #95994 ), #38948 ) ; +#88958 = VERTEX_POINT ( 'NONE', #10329 ) ; +#88959 = PRESENTATION_STYLE_ASSIGNMENT (( #96073 ) ) ; +#88960 = ADVANCED_FACE ( 'NONE', ( #11840 ), #3278, .T. ) ; +#88961 = AXIS2_PLACEMENT_3D ( 'NONE', #70058, #54796, #69550 ) ; +#88962 = ORIENTED_EDGE ( 'NONE', *, *, #86874, .T. ) ; +#88963 = FILL_AREA_STYLE ('',( #50686 ) ) ; +#88964 = ADVANCED_FACE ( 'NONE', ( #44075 ), #83399, .T. ) ; +#88965 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#88966 = LINE ( 'NONE', #48152, #26304 ) ; +#88967 = PRESENTATION_STYLE_ASSIGNMENT (( #72631 ) ) ; +#88968 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000089, -0.02000000000000000042 ) ) ; +#88969 = VERTEX_POINT ( 'NONE', #98613 ) ; +#88970 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8992 ) ) ; +#88971 = SURFACE_STYLE_USAGE ( .BOTH. , #3198 ) ; +#88972 = VERTEX_POINT ( 'NONE', #22097 ) ; +#88973 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #13902 ), #7383 ) ; +#88974 = SURFACE_STYLE_USAGE ( .BOTH. , #64980 ) ; +#88975 = SURFACE_STYLE_USAGE ( .BOTH. , #97100 ) ; +#88976 = VERTEX_POINT ( 'NONE', #6691 ) ; +#88977 = MANIFOLD_SOLID_BREP ( 'ÊäÈë75', #2941 ) ; +#88978 = ORIENTED_EDGE ( 'NONE', *, *, #55871, .F. ) ; +#88979 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#88980 = FACE_OUTER_BOUND ( 'NONE', #95951, .T. ) ; +#88981 = LINE ( 'NONE', #30051, #96244 ) ; +#88983 = SURFACE_STYLE_USAGE ( .BOTH. , #66991 ) ; +#88982 = FILL_AREA_STYLE ('',( #26210 ) ) ; +#88984 = ORIENTED_EDGE ( 'NONE', *, *, #20216, .F. ) ; +#88987 = ORIENTED_EDGE ( 'NONE', *, *, #50325, .T. ) ; +#88986 = ORIENTED_EDGE ( 'NONE', *, *, #35430, .F. ) ; +#88985 = STYLED_ITEM ( 'NONE', ( #80118 ), #73142 ) ; +#88988 = ORIENTED_EDGE ( 'NONE', *, *, #13555, .F. ) ; +#88989 = CARTESIAN_POINT ( 'NONE', ( -0.1500000000000000222, 0.1499999999999999667, -1.504632769052527497E-33 ) ) ; +#88990 = VECTOR ( 'NONE', #49989, 1000.000000000000000 ) ; +#88991 = EDGE_CURVE ( 'NONE', #95367, #53059, #75240, .T. ) ; +#88992 = EDGE_LOOP ( 'NONE', ( #44538, #7707, #1467, #90980 ) ) ; +#88994 = ORIENTED_EDGE ( 'NONE', *, *, #39350, .T. ) ; +#88993 = FILL_AREA_STYLE_COLOUR ( '', #49323 ) ; +#88995 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#88996 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#88997 = STYLED_ITEM ( 'NONE', ( #94765 ), #90361 ) ; +#88999 = SURFACE_STYLE_USAGE ( .BOTH. , #35407 ) ; +#88998 = AXIS2_PLACEMENT_3D ( 'NONE', #70041, #47584, #56793 ) ; +#89000 = ORIENTED_EDGE ( 'NONE', *, *, #40737, .T. ) ; +#89002 = ADVANCED_FACE ( 'NONE', ( #5733 ), #6211, .T. ) ; +#89001 = LINE ( 'NONE', #33381, #73387 ) ; +#89003 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89004 = VERTEX_POINT ( 'NONE', #62436 ) ; +#89005 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#89006 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89007 = VECTOR ( 'NONE', #54973, 1000.000000000000000 ) ; +#89008 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31934 ), #53071 ) ; +#89009 = SURFACE_STYLE_FILL_AREA ( #96631 ) ; +#89010 = SURFACE_STYLE_FILL_AREA ( #12313 ) ; +#89012 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89011 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15444 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96628, #26731, #68861 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89013 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89014 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#89015 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89016 = FACE_OUTER_BOUND ( 'NONE', #57902, .T. ) ; +#89017 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31940 ) ) ; +#89018 = LINE ( 'NONE', #65028, #89700 ) ; +#89019 = SURFACE_STYLE_USAGE ( .BOTH. , #4732 ) ; +#89020 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89021 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#89022 = SURFACE_SIDE_STYLE ('',( #57920 ) ) ; +#89023 = EDGE_CURVE ( 'NONE', #85330, #40777, #9720, .T. ) ; +#89024 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64604 ), #23799 ) ; +#89025 = VECTOR ( 'NONE', #27169, 1000.000000000000000 ) ; +#89026 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#89027 = CARTESIAN_POINT ( 'NONE', ( 1.047921542718980081, -0.9264544496121609463, 0.8299999999999999600 ) ) ; +#89028 = ORIENTED_EDGE ( 'NONE', *, *, #42045, .T. ) ; +#89029 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#89030 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#89031 = CARTESIAN_POINT ( 'NONE', ( 4.386473164892289667, 1.425172666015749989, -11.91983987436904080 ) ) ; +#89032 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.000000000000000000 ) ) ; +#89033 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97154 ) ) ; +#89034 = ORIENTED_EDGE ( 'NONE', *, *, #29320, .T. ) ; +#89035 = SURFACE_SIDE_STYLE ('',( #17539 ) ) ; +#89036 = LINE ( 'NONE', #10834, #82901 ) ; +#89038 = SURFACE_STYLE_USAGE ( .BOTH. , #65529 ) ; +#89037 = CARTESIAN_POINT ( 'NONE', ( 9.076050999999999647, 8.958225000000000549, 0.8991599999999999593 ) ) ; +#89039 = CARTESIAN_POINT ( 'NONE', ( 1.616346165234739951, -0.9925253384799740397, 0.8100000000000000533 ) ) ; +#89040 = VECTOR ( 'NONE', #76932, 1000.000000000000000 ) ; +#89041 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89042 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89043 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #4654 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79555, #9519, #33086 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89044 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.00000000000000000, 0.000000000000000000 ) ) ; +#89045 = VERTEX_POINT ( 'NONE', #56302 ) ; +#89046 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#89047 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89048 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89049 = SURFACE_STYLE_USAGE ( .BOTH. , #26776 ) ; +#89050 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89051 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89052 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999833, -0.02000000000000000042, 0.1500000000000000222 ) ) ; +#89053 = FILL_AREA_STYLE_COLOUR ( '', #5737 ) ; +#89054 = FILL_AREA_STYLE_COLOUR ( '', #91505 ) ; +#89055 = VECTOR ( 'NONE', #25868, 1000.000000000000000 ) ; +#89056 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#89057 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#89058 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#89059 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1662, 'distance_accuracy_value', 'NONE'); +#89060 = CARTESIAN_POINT ( 'NONE', ( 10.25691899999999990, 3.831700999999999802, 0.8648700000000000276 ) ) ; +#89061 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000533, 0.000000000000000000 ) ) ; +#89062 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#89063 = VERTEX_POINT ( 'NONE', #114 ) ; +#89064 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89065 = EDGE_LOOP ( 'NONE', ( #71797, #31976, #63092, #55214 ) ) ; +#89066 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89067 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79812, 'distance_accuracy_value', 'NONE'); +#89068 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93633, 'distance_accuracy_value', 'NONE'); +#89069 = EDGE_CURVE ( 'NONE', #57013, #21416, #1129, .T. ) ; +#89070 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#89071 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#89072 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89073 = CARTESIAN_POINT ( 'NONE', ( -1.394394100198578679, -1.318629679536714949, 0.8099999999997531397 ) ) ; +#89074 = STYLED_ITEM ( 'NONE', ( #95792 ), #83777 ) ; +#89075 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89076 = STYLED_ITEM ( 'NONE', ( #18435 ), #54498 ) ; +#89077 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89078 = PLANE ( 'NONE', #1591 ) ; +#89079 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.699999999999999956, -0.02000000000002305142 ) ) ; +#89080 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62982, #94043, #55328, #16444 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#89081 = ORIENTED_EDGE ( 'NONE', *, *, #75880, .T. ) ; +#89082 = PRESENTATION_STYLE_ASSIGNMENT (( #65085 ) ) ; +#89083 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7669, 'distance_accuracy_value', 'NONE'); +#89084 = EDGE_CURVE ( 'NONE', #4472, #6047, #32289, .T. ) ; +#89085 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#89086 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67829 ) ) ; +#89087 = ORIENTED_EDGE ( 'NONE', *, *, #30729, .T. ) ; +#89088 = SURFACE_STYLE_USAGE ( .BOTH. , #57974 ) ; +#89089 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89090 = EDGE_CURVE ( 'NONE', #30456, #99988, #39941, .T. ) ; +#89091 = VECTOR ( 'NONE', #25843, 1000.000000000000000 ) ; +#89092 = SURFACE_STYLE_FILL_AREA ( #34483 ) ; +#89093 = SURFACE_SIDE_STYLE ('',( #3318 ) ) ; +#89094 = FILL_AREA_STYLE ('',( #89587 ) ) ; +#89095 = VECTOR ( 'NONE', #74479, 1000.000000000000000 ) ; +#89096 = ORIENTED_EDGE ( 'NONE', *, *, #72210, .T. ) ; +#89097 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.276179938779915091, -0.02000000000000000042 ) ) ; +#89098 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, -3.500000000000000444, 0.000000000000000000 ) ) ; +#89099 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40851, 'distance_accuracy_value', 'NONE'); +#89100 = ORIENTED_EDGE ( 'NONE', *, *, #41802, .T. ) ; +#89101 = CIRCLE ( 'NONE', #90696, 1.968750814464449883 ) ; +#89102 = FILL_AREA_STYLE_COLOUR ( '', #55415 ) ; +#89103 = LINE ( 'NONE', #3330, #88580 ) ; +#89104 = CARTESIAN_POINT ( 'NONE', ( -1.072112542549561898, -1.245397870623744963, 0.8099999999998072076 ) ) ; +#89105 = LINE ( 'NONE', #19129, #51674 ) ; +#89106 = PRESENTATION_STYLE_ASSIGNMENT (( #26839 ) ) ; +#89107 = STYLED_ITEM ( 'NONE', ( #100358 ), #5125 ) ; +#89108 = AXIS2_PLACEMENT_3D ( 'NONE', #37007, #7761, #100161 ) ; +#89109 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22261 ), #69465 ) ; +#89110 = ORIENTED_EDGE ( 'NONE', *, *, #35795, .T. ) ; +#89111 = ORIENTED_EDGE ( 'NONE', *, *, #34722, .F. ) ; +#89112 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20652 ), #18978 ) ; +#89113 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#89115 = SURFACE_STYLE_USAGE ( .BOTH. , #35014 ) ; +#89114 = FACE_OUTER_BOUND ( 'NONE', #44989, .T. ) ; +#89116 = EDGE_CURVE ( 'NONE', #68052, #88713, #46572, .T. ) ; +#89117 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4849999999999999867, 0.2500000000000000000 ) ) ; +#89118 = LINE ( 'NONE', #42656, #98023 ) ; +#89119 = ORIENTED_EDGE ( 'NONE', *, *, #73701, .T. ) ; +#89120 = FILL_AREA_STYLE_COLOUR ( '', #13689 ) ; +#89121 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89122 = EDGE_LOOP ( 'NONE', ( #53946, #44347, #42301, #36942 ) ) ; +#89123 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67875 ), #7530 ) ; +#89124 = SURFACE_SIDE_STYLE ('',( #10919 ) ) ; +#89125 = VERTEX_POINT ( 'NONE', #15415 ) ; +#89126 = ORIENTED_EDGE ( 'NONE', *, *, #38301, .T. ) ; +#89127 = CARTESIAN_POINT ( 'NONE', ( 1.146163979091146423, -1.212686486869580582, 0.8099999999998557243 ) ) ; +#89129 = CARTESIAN_POINT ( 'NONE', ( 2.000000000000000000, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#89128 = FACE_OUTER_BOUND ( 'NONE', #48654, .T. ) ; +#89130 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44923 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #47061, #71578, #9196 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89131 = SURFACE_STYLE_FILL_AREA ( #19683 ) ; +#89132 = EDGE_LOOP ( 'NONE', ( #84549, #52175, #88617, #55502 ) ) ; +#89133 = FILL_AREA_STYLE_COLOUR ( '', #53215 ) ; +#89134 = VECTOR ( 'NONE', #55424, 1000.000000000000000 ) ; +#89135 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98874 ) ) ; +#89136 = PLANE ( 'NONE', #45775 ) ; +#89137 = VERTEX_POINT ( 'NONE', #77731 ) ; +#89138 = CARTESIAN_POINT ( 'NONE', ( 1.356532926677350037, -1.378727886756609955, 0.8299999999999999600 ) ) ; +#89139 = ORIENTED_EDGE ( 'NONE', *, *, #62721, .T. ) ; +#89140 = FILL_AREA_STYLE ('',( #25864 ) ) ; +#89141 = SURFACE_STYLE_FILL_AREA ( #51858 ) ; +#89142 = CARTESIAN_POINT ( 'NONE', ( -1.215673047985899924, -1.210702855844099979, 0.8100000000000000533 ) ) ; +#89143 = MANIFOLD_SOLID_BREP ( 'ÊäÈë70', #82819 ) ; +#89144 = VECTOR ( 'NONE', #19845, 1000.000000000000000 ) ; +#89145 = EDGE_CURVE ( 'NONE', #59761, #85325, #70055, .T. ) ; +#89146 = AXIS2_PLACEMENT_3D ( 'NONE', #88500, #32870, #10284 ) ; +#89147 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8648700000000000276 ) ) ; +#89148 = AXIS2_PLACEMENT_3D ( 'NONE', #38024, #77306, #44645 ) ; +#89150 = ADVANCED_FACE ( 'NONE', ( #63461 ), #95033, .T. ) ; +#89149 = FACE_OUTER_BOUND ( 'NONE', #59925, .T. ) ; +#89151 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#89152 = SURFACE_SIDE_STYLE ('',( #19700 ) ) ; +#89153 = ORIENTED_EDGE ( 'NONE', *, *, #90894, .T. ) ; +#89154 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89155 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#89156 = STYLED_ITEM ( 'NONE', ( #85378 ), #62234 ) ; +#89158 = SURFACE_SIDE_STYLE ('',( #26886 ) ) ; +#89157 = FACE_OUTER_BOUND ( 'NONE', #12427, .T. ) ; +#89159 = VECTOR ( 'NONE', #100341, 1000.000000000000000 ) ; +#89160 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#89161 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#89162 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89163 = CLOSED_SHELL ( 'NONE', ( #25471, #86190, #8501, #25592, #77921, #74614 ) ) ; +#89164 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8648700000000000276 ) ) ; +#89165 = EDGE_CURVE ( 'NONE', #53326, #95862, #61891, .T. ) ; +#89166 = ORIENTED_EDGE ( 'NONE', *, *, #26188, .T. ) ; +#89167 = FILL_AREA_STYLE_COLOUR ( '', #35889 ) ; +#89168 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87564 ), #56622 ) ; +#89169 = LINE ( 'NONE', #82023, #82316 ) ; +#89170 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#89171 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#89172 = CARTESIAN_POINT ( 'NONE', ( 0.3152191558441549968, -1.254058441558439929, 0.8299999999999999600 ) ) ; +#89173 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62487, 'distance_accuracy_value', 'NONE'); +#89174 = SURFACE_SIDE_STYLE ('',( #58069 ) ) ; +#89175 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#89176 = SURFACE_SIDE_STYLE ('',( #66192 ) ) ; +#89177 = STYLED_ITEM ( 'NONE', ( #20749 ), #5290 ) ; +#89178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89179 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105604999999999727, 0.8991599999999999593 ) ) ; +#89180 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89181 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89182 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89183 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#89184 = PLANE ( 'NONE', #74910 ) ; +#89187 = EDGE_CURVE ( 'NONE', #64767, #52613, #37475, .T. ) ; +#89186 = SURFACE_STYLE_FILL_AREA ( #2919 ) ; +#89185 = STYLED_ITEM ( 'NONE', ( #6150 ), #13398 ) ; +#89188 = LINE ( 'NONE', #67677, #518 ) ; +#89189 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #22819, 'design' ) ; +#89190 = LINE ( 'NONE', #90171, #2588 ) ; +#89191 = PLANE ( 'NONE', #29696 ) ; +#89192 = ORIENTED_EDGE ( 'NONE', *, *, #84999, .F. ) ; +#89193 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89194 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46852, 'distance_accuracy_value', 'NONE'); +#89195 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89196 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22544, 'distance_accuracy_value', 'NONE'); +#89198 = SURFACE_SIDE_STYLE ('',( #5624 ) ) ; +#89197 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89199 = AXIS2_PLACEMENT_3D ( 'NONE', #77584, #22978, #15252 ) ; +#89200 = EDGE_CURVE ( 'NONE', #13654, #5418, #16805, .T. ) ; +#89201 = PRESENTATION_STYLE_ASSIGNMENT (( #58095 ) ) ; +#89202 = STYLED_ITEM ( 'NONE', ( #52126 ), #30499 ) ; +#89203 = ORIENTED_EDGE ( 'NONE', *, *, #86978, .T. ) ; +#89204 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89205 = LINE ( 'NONE', #26423, #73456 ) ; +#89206 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89207 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89208 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16053, 'distance_accuracy_value', 'NONE'); +#89210 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#89209 = AXIS2_PLACEMENT_3D ( 'NONE', #92886, #99975, #24031 ) ; +#89211 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89212 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58774, 'distance_accuracy_value', 'NONE'); +#89213 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89214 = ORIENTED_EDGE ( 'NONE', *, *, #72686, .F. ) ; +#89215 = ORIENTED_EDGE ( 'NONE', *, *, #30197, .T. ) ; +#89216 = SURFACE_STYLE_FILL_AREA ( #48917 ) ; +#89217 = LINE ( 'NONE', #50447, #62201 ) ; +#89218 = ORIENTED_EDGE ( 'NONE', *, *, #28756, .F. ) ; +#89219 = CARTESIAN_POINT ( 'NONE', ( 1.736362623504380087, -1.223383224893549892, 0.8299999999999999600 ) ) ; +#89220 = EDGE_CURVE ( 'NONE', #74437, #44133, #64937, .T. ) ; +#89221 = STYLED_ITEM ( 'NONE', ( #1103 ), #79237 ) ; +#89222 = SURFACE_STYLE_FILL_AREA ( #82572 ) ; +#89223 = CARTESIAN_POINT ( 'NONE', ( 3.266666666666632857, -1.699999999999999956, 0.000000000000000000 ) ) ; +#89224 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89225 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89226 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #30538, #42085 ) ; +#89227 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89228 = EDGE_CURVE ( 'NONE', #51090, #82725, #74112, .T. ) ; +#89229 = SURFACE_STYLE_USAGE ( .BOTH. , #58115 ) ; +#89231 = VERTEX_POINT ( 'NONE', #2157 ) ; +#89230 = VERTEX_POINT ( 'NONE', #72582 ) ; +#89232 = VECTOR ( 'NONE', #50076, 1000.000000000000000 ) ; +#89233 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85692 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98244, #36059, #89162 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89234 = ORIENTED_EDGE ( 'NONE', *, *, #81945, .T. ) ; +#89235 = VERTEX_POINT ( 'NONE', #97046 ) ; +#89236 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#89237 = AXIS2_PLACEMENT_3D ( 'NONE', #35370, #89464, #49671 ) ; +#89238 = CARTESIAN_POINT ( 'NONE', ( 1.854034869405480013, -1.451435312150680224, 0.8100000000000000533 ) ) ; +#89239 = VECTOR ( 'NONE', #15307, 1000.000000000000000 ) ; +#89240 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89241 = VERTEX_POINT ( 'NONE', #58823 ) ; +#89242 = SHAPE_REPRESENTATION ( 'ESP32-S3_20210301.xtd', ( #82894 ), #38739 ) ; +#89243 = CLOSED_SHELL ( 'NONE', ( #56389, #96612, #48508, #34525, #62640, #39651 ) ) ; +#89244 = ADVANCED_FACE ( 'NONE', ( #34328 ), #80780, .F. ) ; +#89245 = VECTOR ( 'NONE', #43182, 1000.000000000000000 ) ; +#89246 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89247 = ORIENTED_EDGE ( 'NONE', *, *, #31489, .T. ) ; +#89248 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8100000000000000533 ) ) ; +#89249 = ORIENTED_EDGE ( 'NONE', *, *, #73378, .F. ) ; +#89251 = CYLINDRICAL_SURFACE ( 'NONE', #51769, 0.04999999999999999584 ) ; +#89250 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89252 = AXIS2_PLACEMENT_3D ( 'NONE', #15832, #7601, #1563 ) ; +#89253 = ORIENTED_EDGE ( 'NONE', *, *, #26429, .T. ) ; +#89254 = ORIENTED_EDGE ( 'NONE', *, *, #97115, .T. ) ; +#89255 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82687 ), #40352 ) ; +#89257 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89256 = PRESENTATION_STYLE_ASSIGNMENT (( #40785 ) ) ; +#89258 = CARTESIAN_POINT ( 'NONE', ( 1.894788238603390296, -1.280379325981960026, 0.8300000000000004041 ) ) ; +#89259 = EDGE_LOOP ( 'NONE', ( #10930, #89478, #40905, #27850 ) ) ; +#89260 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89261 = ORIENTED_EDGE ( 'NONE', *, *, #78146, .F. ) ; +#89262 = CARTESIAN_POINT ( 'NONE', ( -0.1534467802446229934, -0.9032194100038879458, 0.8100000000000000533 ) ) ; +#89263 = LINE ( 'NONE', #26984, #34270 ) ; +#89264 = EDGE_LOOP ( 'NONE', ( #99672, #62239, #58524, #73660 ) ) ; +#89265 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89266 = ORIENTED_EDGE ( 'NONE', *, *, #44644, .T. ) ; +#89267 = ORIENTED_EDGE ( 'NONE', *, *, #48807, .T. ) ; +#89268 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89269 = SURFACE_STYLE_FILL_AREA ( #97385 ) ; +#89270 = SURFACE_SIDE_STYLE ('',( #58162 ) ) ; +#89271 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81055 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58053, #27902, #65166 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89272 = EDGE_CURVE ( 'NONE', #59435, #37756, #92406, .T. ) ; +#89273 = EDGE_CURVE ( 'NONE', #7307, #12805, #36809, .T. ) ; +#89274 = SURFACE_STYLE_FILL_AREA ( #50991 ) ; +#89275 = LINE ( 'NONE', #19309, #71442 ) ; +#89276 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95717 ), #71336 ) ; +#89277 = EDGE_LOOP ( 'NONE', ( #100284, #91709, #20282, #5729 ) ) ; +#89278 = SURFACE_SIDE_STYLE ('',( #56657 ) ) ; +#89279 = ORIENTED_EDGE ( 'NONE', *, *, #73385, .F. ) ; +#89280 = FILL_AREA_STYLE_COLOUR ( '', #100869 ) ; +#89281 = LINE ( 'NONE', #2511, #52950 ) ; +#89282 = VECTOR ( 'NONE', #7961, 1000.000000000000000 ) ; +#89283 = VECTOR ( 'NONE', #10331, 1000.000000000000000 ) ; +#89284 = SURFACE_STYLE_FILL_AREA ( #97885 ) ; +#89285 = SURFACE_SIDE_STYLE ('',( #35185 ) ) ; +#89286 = CARTESIAN_POINT ( 'NONE', ( -2.583333333333333481, -3.100000000000000533, 0.000000000000000000 ) ) ; +#89287 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#89288 = EDGE_CURVE ( 'NONE', #97238, #21167, #98987, .T. ) ; +#89290 = ORIENTED_EDGE ( 'NONE', *, *, #32602, .T. ) ; +#89289 = STYLED_ITEM ( 'NONE', ( #97664 ), #55207 ) ; +#89291 = ADVANCED_FACE ( 'NONE', ( #60810 ), #52642, .F. ) ; +#89292 = CYLINDRICAL_SURFACE ( 'NONE', #86786, 0.04999999999999991257 ) ; +#89293 = PRESENTATION_STYLE_ASSIGNMENT (( #67783 ) ) ; +#89294 = CARTESIAN_POINT ( 'NONE', ( 0.2602179779670369952, -0.9240726320973919883, 0.8299999999999999600 ) ) ; +#89295 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#89296 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89297 = SURFACE_STYLE_FILL_AREA ( #65817 ) ; +#89298 = EDGE_CURVE ( 'NONE', #86388, #14207, #76599, .T. ) ; +#89299 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89300 = STYLED_ITEM ( 'NONE', ( #79972 ), #17094 ) ; +#89302 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34562 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81711, #11644, #74031 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89301 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89303 = PRESENTATION_STYLE_ASSIGNMENT (( #58194 ) ) ; +#89304 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#89305 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14235 ) ) ; +#89306 = EDGE_CURVE ( 'NONE', #12677, #73024, #33397, .T. ) ; +#89307 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89308 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #79776, 'distance_accuracy_value', 'NONE'); +#89309 = VERTEX_POINT ( 'NONE', #35832 ) ; +#89310 = CLOSED_SHELL ( 'NONE', ( #74241, #26602, #58801, #19621, #32016, #4858 ) ) ; +#89311 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89312 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89313 = EDGE_LOOP ( 'NONE', ( #30564, #69047, #539, #68694 ) ) ; +#89314 = FILL_AREA_STYLE ('',( #28523 ) ) ; +#89315 = EDGE_CURVE ( 'NONE', #80438, #40477, #45908, .T. ) ; +#89316 = SURFACE_STYLE_USAGE ( .BOTH. , #96941 ) ; +#89317 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26031 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11623, #73005, #64336 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89318 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 7.826853999999999090, 0.8991599999999999593 ) ) ; +#89319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89320 = EDGE_CURVE ( 'NONE', #49779, #19782, #98496, .T. ) ; +#89321 = VERTEX_POINT ( 'NONE', #90931 ) ; +#89322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45064 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37160, #34787, #6434 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89323 = ADVANCED_FACE ( 'NONE', ( #44432 ), #20983, .T. ) ; +#89324 = ORIENTED_EDGE ( 'NONE', *, *, #62109, .T. ) ; +#89325 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#89326 = SURFACE_SIDE_STYLE ('',( #58216 ) ) ; +#89327 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89328 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29646 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99852, #7957, #97191 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89329 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.000000000000000000 ) ) ; +#89330 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 9.150000000000000355, 0.000000000000000000 ) ) ; +#89331 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98262, 'distance_accuracy_value', 'NONE'); +#89332 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#89333 = FACE_OUTER_BOUND ( 'NONE', #30800, .T. ) ; +#89334 = ORIENTED_EDGE ( 'NONE', *, *, #95193, .F. ) ; +#89335 = AXIS2_PLACEMENT_3D ( 'NONE', #69458, #39336, #45957 ) ; +#89336 = EDGE_LOOP ( 'NONE', ( #67924, #86468, #65879, #87299, #9917, #87062 ) ) ; +#89337 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89338 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, -8.400000000000000355, -0.2000000000000000111 ) ) ; +#89339 = LINE ( 'NONE', #43370, #77618 ) ; +#89340 = CARTESIAN_POINT ( 'NONE', ( -1.009821428571429980, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#89341 = VECTOR ( 'NONE', #76840, 1000.000000000000000 ) ; +#89342 = CARTESIAN_POINT ( 'NONE', ( -0.3725002807689830053, -1.021003931094770056, 0.8299999999999999600 ) ) ; +#89343 = EDGE_CURVE ( 'NONE', #18616, #39359, #69415, .T. ) ; +#89344 = PLANE ( 'NONE', #51367 ) ; +#89346 = ORIENTED_EDGE ( 'NONE', *, *, #58572, .F. ) ; +#89345 = ORIENTED_EDGE ( 'NONE', *, *, #5846, .F. ) ; +#89347 = ORIENTED_EDGE ( 'NONE', *, *, #17060, .T. ) ; +#89348 = FACE_OUTER_BOUND ( 'NONE', #90612, .T. ) ; +#89349 = STYLED_ITEM ( 'NONE', ( #68315 ), #84273 ) ; +#89351 = LINE ( 'NONE', #57237, #72401 ) ; +#89350 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89352 = ORIENTED_EDGE ( 'NONE', *, *, #7258, .F. ) ; +#89353 = EDGE_CURVE ( 'NONE', #36910, #38401, #45924, .T. ) ; +#89354 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #41769 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7698, #119, #8209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89355 = ORIENTED_EDGE ( 'NONE', *, *, #344, .F. ) ; +#89356 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#89357 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#89358 = AXIS2_PLACEMENT_3D ( 'NONE', #74201, #42055, #65514 ) ; +#89360 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#89359 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999119316, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#89361 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89362 = ORIENTED_EDGE ( 'NONE', *, *, #46325, .T. ) ; +#89363 = ADVANCED_FACE ( 'NONE', ( #86279 ), #93398, .T. ) ; +#89364 = ORIENTED_EDGE ( 'NONE', *, *, #42612, .F. ) ; +#89365 = VERTEX_POINT ( 'NONE', #7573 ) ; +#89366 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980105, 0.6500000000000001332, -0.02000000000000000042 ) ) ; +#89367 = CIRCLE ( 'NONE', #14303, 0.009999999999999998473 ) ; +#89368 = EDGE_CURVE ( 'NONE', #62347, #57652, #25037, .T. ) ; +#89369 = VERTEX_POINT ( 'NONE', #38815 ) ; +#89371 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89370 = FACE_OUTER_BOUND ( 'NONE', #6527, .T. ) ; +#89372 = EDGE_LOOP ( 'NONE', ( #82235, #23070, #24988, #43749 ) ) ; +#89373 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#89374 = CLOSED_SHELL ( 'NONE', ( #90639, #71132, #74501, #23939, #21261, #36626, #32866, #74012, #82990, #35390, #37967, #49668, #36445, #9541 ) ) ; +#89375 = DIRECTION ( 'NONE', ( -0.7071090539100467476, 0.7071045084557434635, 0.000000000000000000 ) ) ; +#89376 = ORIENTED_EDGE ( 'NONE', *, *, #73439, .F. ) ; +#89377 = ORIENTED_EDGE ( 'NONE', *, *, #37689, .T. ) ; +#89378 = FILL_AREA_STYLE_COLOUR ( '', #26968 ) ; +#89379 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#89380 = FILL_AREA_STYLE_COLOUR ( '', #98593 ) ; +#89381 = PLANE ( 'NONE', #89389 ) ; +#89382 = CARTESIAN_POINT ( 'NONE', ( -1.215673047985899924, -1.210702855844099979, 0.8300000000000000711 ) ) ; +#89384 = EDGE_CURVE ( 'NONE', #49647, #81624, #62830, .T. ) ; +#89383 = CYLINDRICAL_SURFACE ( 'NONE', #31449, 0.01000000000000002623 ) ; +#89385 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89386 = FILL_AREA_STYLE ('',( #51621 ) ) ; +#89387 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#89388 = LINE ( 'NONE', #97012, #41038 ) ; +#89389 = AXIS2_PLACEMENT_3D ( 'NONE', #85099, #93228, #53967 ) ; +#89390 = EDGE_LOOP ( 'NONE', ( #13705, #84965, #21439, #55909 ) ) ; +#89391 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 5.832812999999999803, 0.8648700000000000276 ) ) ; +#89392 = CARTESIAN_POINT ( 'NONE', ( -0.9354363632813189611, -1.053930089500670020, 0.8300000000000000711 ) ) ; +#89393 = VERTEX_POINT ( 'NONE', #16299 ) ; +#89394 = SURFACE_STYLE_USAGE ( .BOTH. , #74589 ) ; +#89395 = SURFACE_STYLE_USAGE ( .BOTH. , #44409 ) ; +#89396 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, 0.4245906043549200204, 0.1900000000000000300 ) ) ; +#89397 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762689420, 0.4849999999999999867, 0.2399999999999999079 ) ) ; +#89398 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#89399 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#89400 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89401 = EDGE_CURVE ( 'NONE', #75965, #17757, #69935, .T. ) ; +#89402 = EDGE_CURVE ( 'NONE', #12756, #97231, #1021, .T. ) ; +#89403 = SURFACE_STYLE_FILL_AREA ( #44417 ) ; +#89404 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71862 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90849, #98417, #5536 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89405 = AXIS2_PLACEMENT_3D ( 'NONE', #26290, #25782, #17570 ) ; +#89406 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#89407 = FILL_AREA_STYLE ('',( #27148 ) ) ; +#89408 = ORIENTED_EDGE ( 'NONE', *, *, #58038, .T. ) ; +#89409 = STYLED_ITEM ( 'NONE', ( #12855 ), #31296 ) ; +#89410 = SURFACE_STYLE_FILL_AREA ( #89906 ) ; +#89411 = CARTESIAN_POINT ( 'NONE', ( -0.04357741169481995497, -1.231872828124784602, 0.8099999999998996891 ) ) ; +#89412 = PLANE ( 'NONE', #26111 ) ; +#89413 = SURFACE_STYLE_FILL_AREA ( #11214 ) ; +#89414 = STYLED_ITEM ( 'NONE', ( #63094 ), #84606 ) ; +#89415 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52406 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28155, #5118, #20468 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89416 = ADVANCED_FACE ( 'NONE', ( #16046 ), #16801, .T. ) ; +#89417 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24123, 'distance_accuracy_value', 'NONE'); +#89418 = ORIENTED_EDGE ( 'NONE', *, *, #82482, .T. ) ; +#89419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89420 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 0.1000000000000000056, -0.1499999999999999944 ) ) ; +#89421 = PLANE ( 'NONE', #31193 ) ; +#89422 = CARTESIAN_POINT ( 'NONE', ( -1.066869350290160279, -0.9766832120545909657, 0.8299999999999999600 ) ) ; +#89423 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#89424 = EDGE_CURVE ( 'NONE', #19573, #62254, #27544, .T. ) ; +#89425 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89426 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#89427 = SURFACE_SIDE_STYLE ('',( #65425 ) ) ; +#89428 = VECTOR ( 'NONE', #24640, 1000.000000000000000 ) ; +#89429 = CARTESIAN_POINT ( 'NONE', ( 9.507386833499916534, 5.557040833499760524, 0.8991599999999999593 ) ) ; +#89430 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#89431 = FILL_AREA_STYLE_COLOUR ( '', #65930 ) ; +#89432 = VECTOR ( 'NONE', #23985, 1000.000000000000000 ) ; +#89433 = EDGE_CURVE ( 'NONE', #22432, #13392, #80162, .T. ) ; +#89434 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.699999999999999956, 0.000000000000000000 ) ) ; +#89435 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16222 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23761, #78379, #759 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89436 = VERTEX_POINT ( 'NONE', #96431 ) ; +#89437 = FILL_AREA_STYLE ('',( #82780 ) ) ; +#89438 = EDGE_CURVE ( 'NONE', #78769, #41411, #27043, .T. ) ; +#89439 = VERTEX_POINT ( 'NONE', #4037 ) ; +#89440 = FILL_AREA_STYLE ('',( #3166 ) ) ; +#89441 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77477, 'distance_accuracy_value', 'NONE'); +#89442 = SURFACE_SIDE_STYLE ('',( #27181 ) ) ; +#89443 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#89445 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81802 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6369, #46721, #15564 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89444 = CARTESIAN_POINT ( 'NONE', ( -1.457264610389610082, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#89446 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89447 = CARTESIAN_POINT ( 'NONE', ( 0.4519550824822715640, -1.244418846105396659, 0.8099999999999999423 ) ) ; +#89448 = FILL_AREA_STYLE ('',( #26175 ) ) ; +#89449 = STYLED_ITEM ( 'NONE', ( #10634 ), #23939 ) ; +#89450 = SURFACE_STYLE_USAGE ( .BOTH. , #9741 ) ; +#89451 = SURFACE_SIDE_STYLE ('',( #20492 ) ) ; +#89452 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89453 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89454 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3692 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28475, #13566, #23835 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89455 = ORIENTED_EDGE ( 'NONE', *, *, #69979, .F. ) ; +#89456 = SURFACE_SIDE_STYLE ('',( #88954 ) ) ; +#89457 = SURFACE_SIDE_STYLE ('',( #66464 ) ) ; +#89458 = SURFACE_SIDE_STYLE ('',( #9245 ) ) ; +#89459 = ORIENTED_EDGE ( 'NONE', *, *, #22644, .F. ) ; +#89460 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89461 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 5.450000000000000178, 0.03429000000000000103 ) ) ; +#89462 = ORIENTED_EDGE ( 'NONE', *, *, #9476, .F. ) ; +#89463 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17452 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39273, #56663, #33671 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89464 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#89465 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #37231 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24919, #95290, #70839 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89466 = FACE_OUTER_BOUND ( 'NONE', #86431, .T. ) ; +#89467 = FILL_AREA_STYLE_COLOUR ( '', #26715 ) ; +#89468 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1424 ), #25933 ) ; +#89469 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89470 = EDGE_CURVE ( 'NONE', #54259, #80806, #18840, .T. ) ; +#89471 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.004999999999999986226, -0.1500000000000000222 ) ) ; +#89472 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89473 = ORIENTED_EDGE ( 'NONE', *, *, #68902, .F. ) ; +#89474 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#89475 = ORIENTED_EDGE ( 'NONE', *, *, #93032, .F. ) ; +#89476 = SURFACE_STYLE_USAGE ( .BOTH. , #96595 ) ; +#89477 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.323820061220084998, 0.000000000000000000 ) ) ; +#89478 = ORIENTED_EDGE ( 'NONE', *, *, #16835, .F. ) ; +#89479 = EDGE_CURVE ( 'NONE', #55952, #82518, #3034, .T. ) ; +#89480 = ORIENTED_EDGE ( 'NONE', *, *, #39735, .T. ) ; +#89481 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89482 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89483 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#89484 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91185 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56053, #58086, #56566 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89486 = LINE ( 'NONE', #19527, #40289 ) ; +#89485 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89487 = ORIENTED_EDGE ( 'NONE', *, *, #78339, .T. ) ; +#89488 = EDGE_CURVE ( 'NONE', #73506, #13767, #18325, .T. ) ; +#89490 = VERTEX_POINT ( 'NONE', #9601 ) ; +#89489 = VERTEX_POINT ( 'NONE', #50034 ) ; +#89491 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8991599999999999593 ) ) ; +#89492 = VERTEX_POINT ( 'NONE', #71982 ) ; +#89493 = SURFACE_STYLE_USAGE ( .BOTH. , #43509 ) ; +#89494 = VECTOR ( 'NONE', #55552, 1000.000000000000000 ) ; +#89495 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #30480, #61686, #85647, #46825 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#89496 = EDGE_CURVE ( 'NONE', #25563, #65486, #33695, .T. ) ; +#89497 = ORIENTED_EDGE ( 'NONE', *, *, #32233, .F. ) ; +#89498 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #17671 ), #22653 ) ; +#89499 = VERTEX_POINT ( 'NONE', #64818 ) ; +#89500 = VECTOR ( 'NONE', #95565, 1000.000000000000000 ) ; +#89501 = AXIS2_PLACEMENT_3D ( 'NONE', #90168, #80163, #41851 ) ; +#89502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89503 = SURFACE_STYLE_USAGE ( .BOTH. , #21541 ) ; +#89504 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#89505 = SURFACE_STYLE_FILL_AREA ( #59398 ) ; +#89506 = ORIENTED_EDGE ( 'NONE', *, *, #63223, .F. ) ; +#89507 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8100000000000610045 ) ) ; +#89508 = LINE ( 'NONE', #27740, #7513 ) ; +#89509 = ORIENTED_EDGE ( 'NONE', *, *, #9867, .T. ) ; +#89510 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55980 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #31446, #53427, #62620 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89511 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47063 ), #48786 ) ; +#89512 = CARTESIAN_POINT ( 'NONE', ( 0.2814011140707955438, -1.359308548237883052, 0.8100000000000001643 ) ) ; +#89513 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8299999999999999600 ) ) ; +#89514 = VECTOR ( 'NONE', #53360, 1000.000000000000000 ) ; +#89515 = PRESENTATION_STYLE_ASSIGNMENT (( #96128 ) ) ; +#89516 = ADVANCED_FACE ( 'NONE', ( #97437 ), #49512, .T. ) ; +#89517 = EDGE_CURVE ( 'NONE', #88242, #56618, #21715, .T. ) ; +#89518 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71584 ), #47071 ) ; +#89519 = PRESENTATION_STYLE_ASSIGNMENT (( #67020 ) ) ; +#89521 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89520 = SURFACE_STYLE_FILL_AREA ( #97136 ) ; +#89522 = SURFACE_STYLE_USAGE ( .BOTH. , #42050 ) ; +#89523 = AXIS2_PLACEMENT_3D ( 'NONE', #26790, #67066, #50295 ) ; +#89524 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89525 = EDGE_LOOP ( 'NONE', ( #6317, #108, #87127, #17636 ) ) ; +#89526 = SURFACE_STYLE_USAGE ( .BOTH. , #66032 ) ; +#89527 = VECTOR ( 'NONE', #11378, 1000.000000000000000 ) ; +#89528 = CARTESIAN_POINT ( 'NONE', ( 1.406489741257900050, -1.236164603532529993, 0.8300000000000022915 ) ) ; +#89529 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89531 = SURFACE_STYLE_FILL_AREA ( #50251 ) ; +#89530 = PRESENTATION_STYLE_ASSIGNMENT (( #96138 ) ) ; +#89532 = SURFACE_STYLE_USAGE ( .BOTH. , #89022 ) ; +#89533 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89534 = EDGE_CURVE ( 'NONE', #61829, #61755, #68314, .T. ) ; +#89535 = LINE ( 'NONE', #51741, #90041 ) ; +#89536 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53667 ), #9558 ) ; +#89537 = ORIENTED_EDGE ( 'NONE', *, *, #16190, .F. ) ; +#89538 = CARTESIAN_POINT ( 'NONE', ( -1.352086563886500059, -1.432289833627879982, 0.8300000000000024025 ) ) ; +#89539 = EDGE_CURVE ( 'NONE', #14049, #93808, #36202, .T. ) ; +#89540 = VECTOR ( 'NONE', #100721, 1000.000000000000114 ) ; +#89541 = VERTEX_POINT ( 'NONE', #20863 ) ; +#89543 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, -3.500000000000000444, 0.000000000000000000 ) ) ; +#89542 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89544 = CARTESIAN_POINT ( 'NONE', ( 1.624720795854639910, -0.9850088450568520448, 0.8299999999999999600 ) ) ; +#89545 = SURFACE_SIDE_STYLE ('',( #35447 ) ) ; +#89546 = STYLED_ITEM ( 'NONE', ( #62713 ), #44164 ) ; +#89547 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89548 = SURFACE_STYLE_FILL_AREA ( #48747 ) ; +#89549 = PRESENTATION_STYLE_ASSIGNMENT (( #11834 ) ) ; +#89550 = ORIENTED_EDGE ( 'NONE', *, *, #74980, .T. ) ; +#89551 = SURFACE_STYLE_FILL_AREA ( #4273 ) ; +#89552 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000020040, 0.1829999999999709914 ) ) ; +#89553 = FILL_AREA_STYLE_COLOUR ( '', #58360 ) ; +#89554 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89555 = VECTOR ( 'NONE', #63089, 1000.000000000000000 ) ; +#89556 = CARTESIAN_POINT ( 'NONE', ( -2.300000000000000266, 3.123820061220085265, 0.000000000000000000 ) ) ; +#89557 = FILL_AREA_STYLE ('',( #12363 ) ) ; +#89558 = PRESENTATION_STYLE_ASSIGNMENT (( #68552 ) ) ; +#89560 = SURFACE_STYLE_FILL_AREA ( #42098 ) ; +#89559 = AXIS2_PLACEMENT_3D ( 'NONE', #40016, #76790, #72664 ) ; +#89561 = CARTESIAN_POINT ( 'NONE', ( -2.183333333333333570, 3.100000000000000533, 0.000000000000000000 ) ) ; +#89562 = ORIENTED_EDGE ( 'NONE', *, *, #80766, .T. ) ; +#89563 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89564 = EDGE_CURVE ( 'NONE', #61132, #46055, #29028, .T. ) ; +#89565 = ORIENTED_EDGE ( 'NONE', *, *, #40436, .F. ) ; +#89566 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78117 ), #92784 ) ; +#89567 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2808578643762690841, -0.1434314575050761598 ) ) ; +#89568 = AXIS2_PLACEMENT_3D ( 'NONE', #97075, #58857, #27192 ) ; +#89570 = DIRECTION ( 'NONE', ( 0.000000000000000000, -3.252606517456513302E-15, 1.000000000000000000 ) ) ; +#89569 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22760 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75860, #14536, #37588 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89571 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, 1.399999999999999911, 0.000000000000000000 ) ) ; +#89572 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89573 = SURFACE_STYLE_USAGE ( .BOTH. , #58473 ) ; +#89574 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#89575 = EDGE_CURVE ( 'NONE', #88860, #3712, #44320, .T. ) ; +#89576 = CIRCLE ( 'NONE', #29434, 0.009999999999999998473 ) ; +#89577 = SURFACE_STYLE_USAGE ( .BOTH. , #33457 ) ; +#89578 = VERTEX_POINT ( 'NONE', #67317 ) ; +#89579 = STYLED_ITEM ( 'NONE', ( #46625 ), #56226 ) ; +#89581 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#89580 = AXIS2_PLACEMENT_3D ( 'NONE', #5217, #98602, #28740 ) ; +#89582 = ORIENTED_EDGE ( 'NONE', *, *, #58027, .F. ) ; +#89583 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89584 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89585 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89586 = EDGE_CURVE ( 'NONE', #83312, #46754, #13123, .T. ) ; +#89587 = FILL_AREA_STYLE_COLOUR ( '', #33291 ) ; +#89588 = VECTOR ( 'NONE', #86769, 1000.000000000000114 ) ; +#89589 = ORIENTED_EDGE ( 'NONE', *, *, #51309, .T. ) ; +#89590 = SURFACE_STYLE_FILL_AREA ( #58492 ) ; +#89591 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89592 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#89593 = PLANE ( 'NONE', #29541 ) ; +#89594 = STYLED_ITEM ( 'NONE', ( #12079 ), #719 ) ; +#89595 = LINE ( 'NONE', #75771, #86146 ) ; +#89596 = ORIENTED_EDGE ( 'NONE', *, *, #90853, .F. ) ; +#89597 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#89598 = FILL_AREA_STYLE ('',( #27322 ) ) ; +#89599 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89600 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74958 ), #58661 ) ; +#89601 = FILL_AREA_STYLE_COLOUR ( '', #25576 ) ; +#89602 = ORIENTED_EDGE ( 'NONE', *, *, #77908, .T. ) ; +#89603 = SURFACE_STYLE_USAGE ( .BOTH. , #96721 ) ; +#89604 = VECTOR ( 'NONE', #41988, 1000.000000000000000 ) ; +#89605 = ADVANCED_FACE ( 'NONE', ( #51033 ), #36705, .T. ) ; +#89606 = VECTOR ( 'NONE', #72879, 1000.000000000000000 ) ; +#89607 = ORIENTED_EDGE ( 'NONE', *, *, #23903, .T. ) ; +#89608 = EDGE_LOOP ( 'NONE', ( #59287, #52241, #15575, #11772 ) ) ; +#89609 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18267, 'distance_accuracy_value', 'NONE'); +#89610 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89611 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89612 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01499999999999998383, 0.1400000000000000133 ) ) ; +#89614 = EDGE_CURVE ( 'NONE', #33509, #61212, #82656, .T. ) ; +#89613 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.4600000000000000200, 0.2250000000000000333 ) ) ; +#89615 = LINE ( 'NONE', #98687, #32034 ) ; +#89616 = FILL_AREA_STYLE ('',( #35519 ) ) ; +#89617 = ORIENTED_EDGE ( 'NONE', *, *, #86467, .F. ) ; +#89618 = FACE_OUTER_BOUND ( 'NONE', #95684, .T. ) ; +#89619 = SURFACE_STYLE_FILL_AREA ( #10913 ) ; +#89620 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#89621 = VECTOR ( 'NONE', #85409, 1000.000000000000000 ) ; +#89622 = ORIENTED_EDGE ( 'NONE', *, *, #57715, .F. ) ; +#89624 = PRESENTATION_STYLE_ASSIGNMENT (( #19153 ) ) ; +#89623 = CARTESIAN_POINT ( 'NONE', ( 1.799876578750339684, -1.066767002799750008, 0.8099999999999998312 ) ) ; +#89625 = VERTEX_POINT ( 'NONE', #53024 ) ; +#89626 = ADVANCED_FACE ( 'NONE', ( #76484 ), #59215, .T. ) ; +#89627 = EDGE_CURVE ( 'NONE', #18075, #37623, #53526, .T. ) ; +#89628 = VECTOR ( 'NONE', #100409, 1000.000000000000000 ) ; +#89630 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89629 = PLANE ( 'NONE', #78909 ) ; +#89631 = ORIENTED_EDGE ( 'NONE', *, *, #28184, .F. ) ; +#89632 = EDGE_CURVE ( 'NONE', #3199, #43395, #46319, .T. ) ; +#89633 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89634 = ADVANCED_FACE ( 'NONE', ( #23380 ), #16132, .T. ) ; +#89635 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#89636 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89637 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 8.300000000000000711, 0.000000000000000000 ) ) ; +#89638 = ORIENTED_EDGE ( 'NONE', *, *, #46767, .T. ) ; +#89639 = CARTESIAN_POINT ( 'NONE', ( 1.688395628309255382E-17, 0.8200000000000000622, -0.1378679656440357226 ) ) ; +#89640 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89641 = ORIENTED_EDGE ( 'NONE', *, *, #80058, .F. ) ; +#89643 = LINE ( 'NONE', #36038, #45390 ) ; +#89642 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89645 = LINE ( 'NONE', #42680, #22934 ) ; +#89644 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89646 = CARTESIAN_POINT ( 'NONE', ( -1.266878993523750108, -1.195322104373929939, 0.8299999999999999600 ) ) ; +#89647 = EDGE_CURVE ( 'NONE', #22428, #99888, #92301, .T. ) ; +#89648 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93297 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78115, #22474, #38315 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89649 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89650 = SURFACE_STYLE_FILL_AREA ( #17294 ) ; +#89651 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 1.500000000000000000, 0.1829999999999870064 ) ) ; +#89652 = SURFACE_STYLE_USAGE ( .BOTH. , #89152 ) ; +#89653 = ADVANCED_FACE ( 'NONE', ( #71736 ), #69283, .T. ) ; +#89654 = ORIENTED_EDGE ( 'NONE', *, *, #60663, .F. ) ; +#89655 = VECTOR ( 'NONE', #71177, 1000.000000000000000 ) ; +#89656 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89657 = STYLED_ITEM ( 'NONE', ( #79508 ), #1598 ) ; +#89660 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89659 = FILL_AREA_STYLE_COLOUR ( '', #6561 ) ; +#89658 = LINE ( 'NONE', #19706, #15269 ) ; +#89661 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#89662 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88965, 'distance_accuracy_value', 'NONE'); +#89663 = AXIS2_PLACEMENT_3D ( 'NONE', #58157, #27492, #4961 ) ; +#89664 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999983569, 3.500000000000000444, -5.977360615245821520E-90 ) ) ; +#89665 = VECTOR ( 'NONE', #41088, 1000.000000000000000 ) ; +#89666 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.09999999999999939493, -0.02000000000001679948 ) ) ; +#89667 = PRESENTATION_STYLE_ASSIGNMENT (( #59063 ) ) ; +#89668 = SURFACE_STYLE_FILL_AREA ( #12978 ) ; +#89669 = VERTEX_POINT ( 'NONE', #58470 ) ; +#89670 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89671 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89672 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, 0.2808578643762690841, 0.1499999999999999389 ) ) ; +#89673 = VECTOR ( 'NONE', #14817, 1000.000000000000000 ) ; +#89674 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#89675 = SURFACE_STYLE_USAGE ( .BOTH. , #89174 ) ; +#89676 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89677 = SURFACE_STYLE_FILL_AREA ( #26902 ) ; +#89678 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#89679 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89680 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89681 = SURFACE_STYLE_USAGE ( .BOTH. , #50900 ) ; +#89682 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#89683 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89684 = PRESENTATION_STYLE_ASSIGNMENT (( #73371 ) ) ; +#89685 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89686 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#89687 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89689 = EDGE_CURVE ( 'NONE', #95367, #23904, #69247, .T. ) ; +#89688 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89690 = ORIENTED_EDGE ( 'NONE', *, *, #65002, .T. ) ; +#89691 = CARTESIAN_POINT ( 'NONE', ( 10.53976224974991283, 8.413752750250088397, 0.8991599999999999593 ) ) ; +#89692 = SURFACE_STYLE_FILL_AREA ( #75370 ) ; +#89693 = STYLED_ITEM ( 'NONE', ( #26682 ), #33153 ) ; +#89694 = FACE_OUTER_BOUND ( 'NONE', #55060, .T. ) ; +#89695 = ORIENTED_EDGE ( 'NONE', *, *, #44700, .F. ) ; +#89696 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89697 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.5000000000000015543, 7.477407789112982559E-79 ) ) ; +#89698 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48906 ), #71778 ) ; +#89699 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89700 = VECTOR ( 'NONE', #17522, 1000.000000000000000 ) ; +#89701 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#89702 = VECTOR ( 'NONE', #61823, 1000.000000000000000 ) ; +#89703 = SURFACE_SIDE_STYLE ('',( #12008 ) ) ; +#89704 = ORIENTED_EDGE ( 'NONE', *, *, #69382, .F. ) ; +#89705 = ORIENTED_EDGE ( 'NONE', *, *, #58756, .F. ) ; +#89706 = CARTESIAN_POINT ( 'NONE', ( 0.0001014610389608714720, 0.6899999999999999467, 0.4397321428571430713 ) ) ; +#89707 = SURFACE_STYLE_FILL_AREA ( #72368 ) ; +#89708 = VERTEX_POINT ( 'NONE', #28290 ) ; +#89709 = CARTESIAN_POINT ( 'NONE', ( 1.818404401970810103, -1.294636995308309890, 0.8299999999999999600 ) ) ; +#89710 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26183 ), #68549 ) ; +#89711 = FACE_OUTER_BOUND ( 'NONE', #7473, .T. ) ; +#89712 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.050000000000000044, 0.000000000000000000 ) ) ; +#89713 = CARTESIAN_POINT ( 'NONE', ( -1.289503315023140084, -0.9165513359838141083, 0.8299999999999997380 ) ) ; +#89714 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #14271, #41901 ) ; +#89715 = SURFACE_STYLE_FILL_AREA ( #26950 ) ; +#89716 = VECTOR ( 'NONE', #50997, 1000.000000000000000 ) ; +#89718 = ORIENTED_EDGE ( 'NONE', *, *, #88918, .T. ) ; +#89717 = ORIENTED_EDGE ( 'NONE', *, *, #15585, .T. ) ; +#89719 = ORIENTED_EDGE ( 'NONE', *, *, #69006, .T. ) ; +#89720 = STYLED_ITEM ( 'NONE', ( #29457 ), #68978 ) ; +#89721 = VECTOR ( 'NONE', #54789, 1000.000000000000000 ) ; +#89722 = ORIENTED_EDGE ( 'NONE', *, *, #92249, .T. ) ; +#89723 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36783, 'distance_accuracy_value', 'NONE'); +#89724 = CARTESIAN_POINT ( 'NONE', ( 1.901147915587950044, -1.336905478629369926, 0.8100000000000000533 ) ) ; +#89725 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#89726 = EDGE_LOOP ( 'NONE', ( #93687, #33823, #50830, #42966 ) ) ; +#89727 = FILL_AREA_STYLE ('',( #59139 ) ) ; +#89728 = SURFACE_SIDE_STYLE ('',( #67245 ) ) ; +#89729 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79430 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88236, #26458, #16724 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89730 = VECTOR ( 'NONE', #12479, 1000.000000000000227 ) ; +#89731 = ORIENTED_EDGE ( 'NONE', *, *, #88770, .F. ) ; +#89732 = ORIENTED_EDGE ( 'NONE', *, *, #12003, .T. ) ; +#89733 = ORIENTED_EDGE ( 'NONE', *, *, #1264, .F. ) ; +#89734 = VECTOR ( 'NONE', #100221, 1000.000000000000000 ) ; +#89736 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89735 = PRESENTATION_STYLE_ASSIGNMENT (( #97371 ) ) ; +#89737 = FILL_AREA_STYLE_COLOUR ( '', #97732 ) ; +#89740 = ORIENTED_EDGE ( 'NONE', *, *, #35506, .T. ) ; +#89739 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21233 ) ) ; +#89738 = PLANE ( 'NONE', #76995 ) ; +#89741 = ADVANCED_FACE ( 'NONE', ( #35969 ), #49782, .T. ) ; +#89742 = VERTEX_POINT ( 'NONE', #26798 ) ; +#89743 = CARTESIAN_POINT ( 'NONE', ( -0.2475423460550890131, -0.9531265814360270205, 0.8100000000000000533 ) ) ; +#89744 = SURFACE_STYLE_USAGE ( .BOTH. , #34650 ) ; +#89745 = EDGE_LOOP ( 'NONE', ( #88678, #80583, #97941, #27274 ) ) ; +#89747 = FACE_OUTER_BOUND ( 'NONE', #98274, .T. ) ; +#89746 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89748 = SURFACE_SIDE_STYLE ('',( #75432 ) ) ; +#89749 = ORIENTED_EDGE ( 'NONE', *, *, #3439, .T. ) ; +#89750 = ORIENTED_EDGE ( 'NONE', *, *, #66433, .T. ) ; +#89751 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89752 = LINE ( 'NONE', #3993, #97110 ) ; +#89753 = CIRCLE ( 'NONE', #68595, 0.009999999999999998473 ) ; +#89754 = VECTOR ( 'NONE', #70735, 1000.000000000000000 ) ; +#89755 = CARTESIAN_POINT ( 'NONE', ( -0.3666263778268459839, -1.099567016183110146, 0.8100000000000000533 ) ) ; +#89756 = PRESENTATION_STYLE_ASSIGNMENT (( #58163 ) ) ; +#89757 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #45029 ) ; +#89758 = SURFACE_SIDE_STYLE ('',( #11061 ) ) ; +#89759 = AXIS2_PLACEMENT_3D ( 'NONE', #3737, #43038, #33906 ) ; +#89760 = ADVANCED_FACE ( 'NONE', ( #97196 ), #43093, .T. ) ; +#89761 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39243 ), #52326 ) ; +#89762 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49279, 'distance_accuracy_value', 'NONE'); +#89763 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9803 ), #66947 ) ; +#89764 = EDGE_LOOP ( 'NONE', ( #77607, #4551, #71025, #44128 ) ) ; +#89765 = FILL_AREA_STYLE_COLOUR ( '', #62693 ) ; +#89766 = ORIENTED_EDGE ( 'NONE', *, *, #51309, .F. ) ; +#89768 = SURFACE_STYLE_USAGE ( .BOTH. , #42322 ) ; +#89767 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32721 ), #14723 ) ; +#89769 = CARTESIAN_POINT ( 'NONE', ( 1.215713331845990064, -1.155903533527329996, 0.8299999999999999600 ) ) ; +#89770 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34343 ) ) ; +#89771 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89772 = SURFACE_STYLE_FILL_AREA ( #65808 ) ; +#89774 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89773 = VECTOR ( 'NONE', #84192, 1000.000000000000000 ) ; +#89775 = SURFACE_STYLE_FILL_AREA ( #82144 ) ; +#89776 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89777 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 7.155103000000000435, 0.8648700000000000276 ) ) ; +#89778 = EDGE_LOOP ( 'NONE', ( #88610, #68840, #73175, #71437 ) ) ; +#89779 = VECTOR ( 'NONE', #73914, 1000.000000000000000 ) ; +#89780 = CARTESIAN_POINT ( 'NONE', ( 9.408390999999999948, 9.545123000000000246, 0.8648700000000000276 ) ) ; +#89781 = CARTESIAN_POINT ( 'NONE', ( 0.1950603093179809899, -0.9901296077683260366, 0.8299999999999999600 ) ) ; +#89782 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#89783 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, 0.09999999999999965861, 1.048695503451051965E-76 ) ) ; +#89784 = SURFACE_STYLE_FILL_AREA ( #35197 ) ; +#89785 = VECTOR ( 'NONE', #7826, 1000.000000000000000 ) ; +#89786 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.499999999999969802, 0.1829999999999999960 ) ) ; +#89787 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92754, 'distance_accuracy_value', 'NONE'); +#89788 = SURFACE_SIDE_STYLE ('',( #58688 ) ) ; +#89789 = SURFACE_STYLE_FILL_AREA ( #43327 ) ; +#89790 = STYLED_ITEM ( 'NONE', ( #57942 ), #1988 ) ; +#89791 = FILL_AREA_STYLE ('',( #28037 ) ) ; +#89792 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89793 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#89794 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89795 = VERTEX_POINT ( 'NONE', #93024 ) ; +#89796 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.000000000000000000, -11.27000000000000135 ) ) ; +#89798 = EDGE_CURVE ( 'NONE', #80616, #10747, #7215, .T. ) ; +#89797 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89799 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#89800 = ORIENTED_EDGE ( 'NONE', *, *, #74639, .T. ) ; +#89801 = LINE ( 'NONE', #82171, #3803 ) ; +#89802 = SURFACE_STYLE_USAGE ( .BOTH. , #12633 ) ; +#89803 = PRESENTATION_STYLE_ASSIGNMENT (( #74505 ) ) ; +#89804 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974021764, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#89805 = VECTOR ( 'NONE', #38562, 1000.000000000000000 ) ; +#89806 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89807 = DIRECTION ( 'NONE', ( -3.614007241618339896E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#89808 = AXIS2_PLACEMENT_3D ( 'NONE', #63498, #38981, #1710 ) ; +#89809 = FACE_OUTER_BOUND ( 'NONE', #35286, .T. ) ; +#89810 = ORIENTED_EDGE ( 'NONE', *, *, #58060, .T. ) ; +#89811 = ORIENTED_EDGE ( 'NONE', *, *, #36778, .F. ) ; +#89812 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89813 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81685 ) ) ; +#89814 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#89815 = FILL_AREA_STYLE_COLOUR ( '', #59539 ) ; +#89816 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.4999999999999998890, 0.000000000000000000 ) ) ; +#89817 = CARTESIAN_POINT ( 'NONE', ( -0.4564379131545099888, -1.136096770074700002, 0.8100000000000000533 ) ) ; +#89818 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#89819 = CARTESIAN_POINT ( 'NONE', ( -1.283785292435335457, -0.9133411585425690316, 0.8100000000000517897 ) ) ; +#89820 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #95314, #25940, #1430, #33592 ), + ( #49923, #1930, #32578, #65212 ), + ( #26933, #25436, #2940, #80559 ), + ( #96828, #64713, #58104, #73396 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000), + ( 0.8047378541243637162, 0.6476030138606861941, 0.6476030138606861941, 0.8047378541243637162), + ( 0.8047378541243637162, 0.6476030138606861941, 0.6476030138606861941, 0.8047378541243637162), + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#89821 = SURFACE_STYLE_USAGE ( .BOTH. , #11124 ) ; +#89822 = ADVANCED_FACE ( 'NONE', ( #5250 ), #68056, .F. ) ; +#89823 = ORIENTED_EDGE ( 'NONE', *, *, #51716, .T. ) ; +#89824 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76772 ), #58904 ) ; +#89825 = AXIS2_PLACEMENT_3D ( 'NONE', #77254, #53295, #30269 ) ; +#89826 = LINE ( 'NONE', #3065, #83012 ) ; +#89827 = ORIENTED_EDGE ( 'NONE', *, *, #86020, .F. ) ; +#89828 = SURFACE_STYLE_USAGE ( .BOTH. , #19380 ) ; +#89829 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #35945, #97171, #58943, #88540 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#89830 = PRESENTATION_STYLE_ASSIGNMENT (( #58731 ) ) ; +#89831 = EDGE_CURVE ( 'NONE', #28663, #71740, #68565, .T. ) ; +#89832 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220085265, 2.700000000000000178, -0.02000000000000000042 ) ) ; +#89833 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89834 = LINE ( 'NONE', #19891, #83870 ) ; +#89835 = FACE_OUTER_BOUND ( 'NONE', #95167, .T. ) ; +#89836 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57289 ), #68672 ) ; +#89837 = DIRECTION ( 'NONE', ( -4.344024262657780003E-34, -1.000000000000000000, 1.224646799147353207E-16 ) ) ; +#89838 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#89839 = CARTESIAN_POINT ( 'NONE', ( -1.293097912083150058, -1.043393888298179917, 0.8299999999999999600 ) ) ; +#89840 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#89842 = VERTEX_POINT ( 'NONE', #59964 ) ; +#89841 = ORIENTED_EDGE ( 'NONE', *, *, #37427, .F. ) ; +#89843 = FILL_AREA_STYLE_COLOUR ( '', #28935 ) ; +#89844 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3428 ) ) ; +#89845 = ORIENTED_EDGE ( 'NONE', *, *, #36205, .T. ) ; +#89846 = CIRCLE ( 'NONE', #55622, 0.009999999999999998473 ) ; +#89848 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#89847 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89849 = VERTEX_POINT ( 'NONE', #100114 ) ; +#89850 = ADVANCED_FACE ( 'NONE', ( #46062 ), #44573, .T. ) ; +#89851 = VERTEX_POINT ( 'NONE', #37465 ) ; +#89852 = FACE_OUTER_BOUND ( 'NONE', #95609, .T. ) ; +#89853 = FACE_OUTER_BOUND ( 'NONE', #34856, .T. ) ; +#89854 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89855 = PLANE ( 'NONE', #19762 ) ; +#89856 = ORIENTED_EDGE ( 'NONE', *, *, #72419, .T. ) ; +#89857 = ORIENTED_EDGE ( 'NONE', *, *, #7737, .F. ) ; +#89858 = ORIENTED_EDGE ( 'NONE', *, *, #23107, .F. ) ; +#89859 = PLANE ( 'NONE', #20387 ) ; +#89860 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24667 ), #58930 ) ; +#89861 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37696 ) ) ; +#89863 = VERTEX_POINT ( 'NONE', #92054 ) ; +#89862 = SURFACE_STYLE_USAGE ( .BOTH. , #67861 ) ; +#89864 = ADVANCED_FACE ( 'NONE', ( #29769 ), #53276, .T. ) ; +#89865 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89866 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#89867 = VERTEX_POINT ( 'NONE', #71103 ) ; +#89868 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#89869 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#89870 = ORIENTED_EDGE ( 'NONE', *, *, #28402, .T. ) ; +#89871 = ORIENTED_EDGE ( 'NONE', *, *, #77551, .T. ) ; +#89872 = PLANE ( 'NONE', #79690 ) ; +#89873 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#89874 = CARTESIAN_POINT ( 'NONE', ( 0.2870738574673178389, -0.9795076273801477384, 0.8099999999999999423 ) ) ; +#89875 = STYLED_ITEM ( 'NONE', ( #9963 ), #51786 ) ; +#89876 = CARTESIAN_POINT ( 'NONE', ( -1.244474960515300044, -1.202560495203230051, 0.8300000000000000711 ) ) ; +#89877 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22750 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40262, #86194, #31575 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89878 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92674 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #29077, #97944, #89847 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89879 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.5238200612200850648, -0.02000000000000000042 ) ) ; +#89881 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89880 = CARTESIAN_POINT ( 'NONE', ( 3.666684500499948651, 7.848067499500048783, 0.8991599999999999593 ) ) ; +#89882 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#89883 = ORIENTED_EDGE ( 'NONE', *, *, #34601, .T. ) ; +#89884 = FILL_AREA_STYLE ('',( #3630 ) ) ; +#89885 = CARTESIAN_POINT ( 'NONE', ( -0.9232862852897980588, -1.401385721107119897, 0.8299999999999999600 ) ) ; +#89886 = EDGE_LOOP ( 'NONE', ( #97101, #72639, #12180, #2099 ) ) ; +#89887 = AXIS2_PLACEMENT_3D ( 'NONE', #38105, #98785, #54439 ) ; +#89888 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89889 = CARTESIAN_POINT ( 'NONE', ( -0.2710399284879780324, -1.444662699359970048, 0.8100000000000000533 ) ) ; +#89890 = LINE ( 'NONE', #19952, #58017 ) ; +#89891 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89893 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#89892 = SURFACE_STYLE_USAGE ( .BOTH. , #19953 ) ; +#89894 = FACE_OUTER_BOUND ( 'NONE', #47514, .T. ) ; +#89895 = CARTESIAN_POINT ( 'NONE', ( 1.794978790831629922, -1.096743473147149928, 0.8299999999999999600 ) ) ; +#89896 = FACE_OUTER_BOUND ( 'NONE', #64554, .T. ) ; +#89897 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58856, #66964, #25667, #56834 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#89898 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89899 = STYLED_ITEM ( 'NONE', ( #46480 ), #34023 ) ; +#89900 = FILL_AREA_STYLE_COLOUR ( '', #33063 ) ; +#89901 = SURFACE_STYLE_USAGE ( .BOTH. , #4623 ) ; +#89902 = VECTOR ( 'NONE', #93237, 1000.000000000000000 ) ; +#89903 = ORIENTED_EDGE ( 'NONE', *, *, #42155, .F. ) ; +#89904 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39388 ), #24790 ) ; +#89905 = ADVANCED_FACE ( 'NONE', ( #48132 ), #25657, .T. ) ; +#89906 = FILL_AREA_STYLE ('',( #98976 ) ) ; +#89908 = SURFACE_SIDE_STYLE ('',( #3143 ) ) ; +#89907 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#89909 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#89910 = VECTOR ( 'NONE', #97524, 1000.000000000000000 ) ; +#89911 = SURFACE_STYLE_FILL_AREA ( #59824 ) ; +#89912 = STYLED_ITEM ( 'NONE', ( #61032 ), #8366 ) ; +#89913 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32859 ) ) ; +#89914 = VERTEX_POINT ( 'NONE', #15942 ) ; +#89915 = FILL_AREA_STYLE ('',( #4153 ) ) ; +#89916 = EDGE_CURVE ( 'NONE', #56748, #12872, #47619, .T. ) ; +#89917 = LINE ( 'NONE', #43453, #3315 ) ; +#89918 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#89919 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77825 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #1292, #32447, #48291 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89920 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99591 ), #45858 ) ; +#89921 = PLANE ( 'NONE', #52411 ) ; +#89922 = LINE ( 'NONE', #70704, #86351 ) ; +#89923 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#89924 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#89925 = ORIENTED_EDGE ( 'NONE', *, *, #89298, .T. ) ; +#89926 = SURFACE_STYLE_USAGE ( .BOTH. , #12755 ) ; +#89927 = ORIENTED_EDGE ( 'NONE', *, *, #32888, .T. ) ; +#89929 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82416, 'distance_accuracy_value', 'NONE'); +#89928 = VECTOR ( 'NONE', #82219, 1000.000000000000114 ) ; +#89930 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50883, 'distance_accuracy_value', 'NONE'); +#89931 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89932 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89933 = SURFACE_SIDE_STYLE ('',( #58340 ) ) ; +#89934 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#89935 = PLANE ( 'NONE', #49343 ) ; +#89936 = FACE_OUTER_BOUND ( 'NONE', #5439, .T. ) ; +#89937 = LINE ( 'NONE', #65971, #27368 ) ; +#89938 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#89939 = SURFACE_SIDE_STYLE ('',( #66462 ) ) ; +#89940 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15114 ), #93175 ) ; +#89941 = ORIENTED_EDGE ( 'NONE', *, *, #95118, .T. ) ; +#89942 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89943 = VERTEX_POINT ( 'NONE', #70589 ) ; +#89944 = LINE ( 'NONE', #60352, #73441 ) ; +#89945 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89946 = SURFACE_STYLE_FILL_AREA ( #38096 ) ; +#89947 = ORIENTED_EDGE ( 'NONE', *, *, #57139, .T. ) ; +#89949 = EDGE_CURVE ( 'NONE', #39998, #23423, #31789, .T. ) ; +#89948 = AXIS2_PLACEMENT_3D ( 'NONE', #89236, #19262, #50465 ) ; +#89950 = EDGE_CURVE ( 'NONE', #33923, #14404, #94027, .T. ) ; +#89951 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89952 = CARTESIAN_POINT ( 'NONE', ( 4.953619000000000661, 9.135001000000000815, 0.8991599999999999593 ) ) ; +#89953 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#89954 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#89955 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#89956 = ORIENTED_EDGE ( 'NONE', *, *, #70033, .F. ) ; +#89957 = VECTOR ( 'NONE', #662, 1000.000000000000114 ) ; +#89958 = PLANE ( 'NONE', #73471 ) ; +#89959 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#89960 = VERTEX_POINT ( 'NONE', #86425 ) ; +#89961 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, -11.57000000000000028 ) ) ; +#89962 = EDGE_LOOP ( 'NONE', ( #62137, #100587, #70776, #59007 ) ) ; +#89963 = ADVANCED_FACE ( 'NONE', ( #33321 ), #24159, .T. ) ; +#89964 = ORIENTED_EDGE ( 'NONE', *, *, #33065, .T. ) ; +#89965 = EDGE_CURVE ( 'NONE', #81283, #45519, #862, .T. ) ; +#89966 = SURFACE_SIDE_STYLE ('',( #49690 ) ) ; +#89967 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#89968 = CARTESIAN_POINT ( 'NONE', ( 1.698015391961940068, -0.9623926821384259922, 0.8300000000000004041 ) ) ; +#89969 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #32915 ), #98130 ) ; +#89970 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69689 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61233, #61732, #71382 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89971 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#89972 = EDGE_LOOP ( 'NONE', ( #56639, #36722, #29198, #21690 ) ) ; +#89974 = VERTEX_POINT ( 'NONE', #41990 ) ; +#89973 = VERTEX_POINT ( 'NONE', #73624 ) ; +#89975 = SURFACE_STYLE_USAGE ( .BOTH. , #82340 ) ; +#89976 = EDGE_LOOP ( 'NONE', ( #70887, #9865, #32573, #62774 ) ) ; +#89977 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38103 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59172, #39658, #23858 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#89978 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -2.250000000000000444, 0.000000000000000000 ) ) ; +#89979 = ORIENTED_EDGE ( 'NONE', *, *, #32039, .F. ) ; +#89981 = ORIENTED_EDGE ( 'NONE', *, *, #100472, .F. ) ; +#89980 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#89982 = VECTOR ( 'NONE', #27144, 1000.000000000000000 ) ; +#89983 = EDGE_CURVE ( 'NONE', #16425, #99462, #57837, .T. ) ; +#89984 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.898280000000000189, 0.8991599999999999593 ) ) ; +#89985 = STYLED_ITEM ( 'NONE', ( #4341 ), #11047 ) ; +#89986 = ORIENTED_EDGE ( 'NONE', *, *, #17620, .F. ) ; +#89987 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#89988 = PLANE ( 'NONE', #81039 ) ; +#89989 = ORIENTED_EDGE ( 'NONE', *, *, #68037, .F. ) ; +#89990 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85103 ), #45921 ) ; +#89991 = ADVANCED_FACE ( 'NONE', ( #43471 ), #5796, .F. ) ; +#89992 = CARTESIAN_POINT ( 'NONE', ( 0.2926936000216603939, -1.349362252575437848, 0.8099999999999999423 ) ) ; +#89993 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.416666666666666519, 0.000000000000000000 ) ) ; +#89994 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#89995 = CARTESIAN_POINT ( 'NONE', ( 12.98106399999999994, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#89996 = LINE ( 'NONE', #67498, #99690 ) ; +#89997 = EDGE_CURVE ( 'NONE', #7390, #97358, #21003, .T. ) ; +#89998 = CARTESIAN_POINT ( 'NONE', ( 1.496131215532870096, -1.321596304865350069, 0.8299999999999999600 ) ) ; +#89999 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90001 = EDGE_CURVE ( 'NONE', #26569, #4210, #48185, .T. ) ; +#90000 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.266666666666639962, 0.000000000000000000 ) ) ; +#90002 = ORIENTED_EDGE ( 'NONE', *, *, #81229, .T. ) ; +#90003 = STYLED_ITEM ( 'NONE', ( #13304 ), #70243 ) ; +#90004 = SURFACE_SIDE_STYLE ('',( #20054 ) ) ; +#90005 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.8999999999999994671, -0.02000000000000000042 ) ) ; +#90006 = FILL_AREA_STYLE_COLOUR ( '', #43659 ) ; +#90007 = VECTOR ( 'NONE', #32317, 1000.000000000000000 ) ; +#90008 = CARTESIAN_POINT ( 'NONE', ( 0.3586905243120019904, -0.9624267057659720015, 0.8299999999999999600 ) ) ; +#90009 = LINE ( 'NONE', #51738, #6126 ) ; +#90010 = SURFACE_SIDE_STYLE ('',( #98584 ) ) ; +#90011 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59087 ), #70471 ) ; +#90012 = LINE ( 'NONE', #58423, #63969 ) ; +#90013 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01085786437626904202, 0.1434314575050762153 ) ) ; +#90014 = ORIENTED_EDGE ( 'NONE', *, *, #98290, .T. ) ; +#90015 = VECTOR ( 'NONE', #87348, 1000.000000000000000 ) ; +#90016 = LINE ( 'NONE', #75703, #51998 ) ; +#90017 = ORIENTED_EDGE ( 'NONE', *, *, #65306, .F. ) ; +#90018 = ADVANCED_FACE ( 'NONE', ( #30632 ), #91936, .T. ) ; +#90019 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 2.100000000000000089, 0.8299999999999999600 ) ) ; +#90021 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90020 = VECTOR ( 'NONE', #16717, 1000.000000000000000 ) ; +#90022 = AXIS2_PLACEMENT_3D ( 'NONE', #60861, #53680, #82816 ) ; +#90023 = CARTESIAN_POINT ( 'NONE', ( -0.2155512272691150200, -1.399421068953929925, 0.8299999999999999600 ) ) ; +#90024 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90025 = PRESENTATION_STYLE_ASSIGNMENT (( #65535 ) ) ; +#90026 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90027 = ORIENTED_EDGE ( 'NONE', *, *, #10209, .F. ) ; +#90028 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999389, 0.5105124837953329830, -1.000000000000000000 ) ) ; +#90029 = EDGE_CURVE ( 'NONE', #60733, #43172, #84289, .T. ) ; +#90030 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#90031 = SURFACE_STYLE_USAGE ( .BOTH. , #80907 ) ; +#90032 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689755, -1.185754870129869909, 0.8099999999999875078 ) ) ; +#90033 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90034 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26434 ), #50935 ) ; +#90035 = FILL_AREA_STYLE ('',( #36438 ) ) ; +#90036 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90037 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90038 = EDGE_CURVE ( 'NONE', #84446, #48055, #44917, .T. ) ; +#90039 = LINE ( 'NONE', #27794, #8207 ) ; +#90040 = SURFACE_STYLE_USAGE ( .BOTH. , #37451 ) ; +#90041 = VECTOR ( 'NONE', #44050, 1000.000000000000000 ) ; +#90042 = SURFACE_SIDE_STYLE ('',( #58953 ) ) ; +#90043 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100319, 'distance_accuracy_value', 'NONE'); +#90044 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90045 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90046 = FILL_AREA_STYLE ('',( #58956 ) ) ; +#90047 = ORIENTED_EDGE ( 'NONE', *, *, #27554, .F. ) ; +#90048 = SURFACE_STYLE_USAGE ( .BOTH. , #44090 ) ; +#90049 = EDGE_CURVE ( 'NONE', #34620, #68307, #30135, .T. ) ; +#90050 = ORIENTED_EDGE ( 'NONE', *, *, #3936, .T. ) ; +#90051 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, -1.157142857142859915, 0.8100000000000000533 ) ) ; +#90052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60493, 'distance_accuracy_value', 'NONE'); +#90053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80536, 'distance_accuracy_value', 'NONE'); +#90054 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90055 = CARTESIAN_POINT ( 'NONE', ( 3.433339000000000141, 6.695483000000000295, 0.8991599999999999593 ) ) ; +#90056 = CARTESIAN_POINT ( 'NONE', ( -1.343749537567388463, -1.441493030236575157, 0.8099999999996628786 ) ) ; +#90057 = PLANE ( 'NONE', #79809 ) ; +#90058 = AXIS2_PLACEMENT_3D ( 'NONE', #58011, #59013, #98194 ) ; +#90059 = CARTESIAN_POINT ( 'NONE', ( -0.6985859609899639500, 1.457596776379110004, 0.8100000000000000533 ) ) ; +#90060 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#90061 = LINE ( 'NONE', #66578, #86333 ) ; +#90062 = FILL_AREA_STYLE_COLOUR ( '', #16688 ) ; +#90063 = ORIENTED_EDGE ( 'NONE', *, *, #11820, .F. ) ; +#90064 = AXIS2_PLACEMENT_3D ( 'NONE', #18799, #49470, #65798 ) ; +#90065 = FACE_OUTER_BOUND ( 'NONE', #62130, .T. ) ; +#90066 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73411, 'distance_accuracy_value', 'NONE'); +#90067 = FILL_AREA_STYLE_COLOUR ( '', #9545 ) ; +#90068 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72150 ), #26464 ) ; +#90069 = ORIENTED_EDGE ( 'NONE', *, *, #33824, .T. ) ; +#90070 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90071 = ADVANCED_FACE ( 'NONE', ( #76618 ), #22492, .F. ) ; +#90072 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90073 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, -0.8000000000000000444 ) ) ; +#90074 = VECTOR ( 'NONE', #82918, 1000.000000000000000 ) ; +#90075 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90076 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.01085786437626905764, -0.1400000000000000411 ) ) ; +#90078 = VERTEX_POINT ( 'NONE', #90948 ) ; +#90077 = VECTOR ( 'NONE', #12702, 1000.000000000000000 ) ; +#90079 = PRESENTATION_STYLE_ASSIGNMENT (( #27832 ) ) ; +#90080 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, 0.000000000000000000, -0.1499999999999999667 ) ) ; +#90081 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45316, 'distance_accuracy_value', 'NONE'); +#90082 = SURFACE_STYLE_FILL_AREA ( #97698 ) ; +#90083 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19965 ) ) ; +#90084 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.000000000000000000 ) ) ; +#90085 = ORIENTED_EDGE ( 'NONE', *, *, #65254, .T. ) ; +#90086 = EDGE_CURVE ( 'NONE', #16, #83112, #67931, .T. ) ; +#90087 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90088 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90089 = STYLED_ITEM ( 'NONE', ( #60194 ), #87664 ) ; +#90090 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90091 = VERTEX_POINT ( 'NONE', #60341 ) ; +#90092 = FILL_AREA_STYLE ('',( #97232 ) ) ; +#90093 = EDGE_LOOP ( 'NONE', ( #63337, #45771, #85703, #74412 ) ) ; +#90095 = EDGE_LOOP ( 'NONE', ( #73912, #50571, #5042, #21777 ) ) ; +#90094 = CARTESIAN_POINT ( 'NONE', ( 0.4333333333333316828, -3.500000000000000000, 0.000000000000000000 ) ) ; +#90096 = CARTESIAN_POINT ( 'NONE', ( 0.8999999999999980238, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#90098 = CARTESIAN_POINT ( 'NONE', ( -1.337569335501239909, -1.448219210431749948, 0.8100000000000000533 ) ) ; +#90097 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37919 ) ) ; +#90099 = SURFACE_STYLE_USAGE ( .BOTH. , #21164 ) ; +#90100 = LINE ( 'NONE', #51330, #26020 ) ; +#90101 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#90102 = LINE ( 'NONE', #33501, #1908 ) ; +#90103 = EDGE_LOOP ( 'NONE', ( #94865, #61559, #8906, #2060 ) ) ; +#90104 = FILL_AREA_STYLE ('',( #10912 ) ) ; +#90105 = CARTESIAN_POINT ( 'NONE', ( -0.9896103896103900510, -1.336241883116880080, 0.8299999999999999600 ) ) ; +#90106 = VECTOR ( 'NONE', #71893, 1000.000000000000000 ) ; +#90107 = VECTOR ( 'NONE', #88028, 1000.000000000000000 ) ; +#90108 = VECTOR ( 'NONE', #55893, 1000.000000000000000 ) ; +#90109 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8991599999999999593 ) ) ; +#90110 = ORIENTED_EDGE ( 'NONE', *, *, #53115, .F. ) ; +#90111 = FILL_AREA_STYLE_COLOUR ( '', #77907 ) ; +#90112 = ORIENTED_EDGE ( 'NONE', *, *, #89983, .T. ) ; +#90113 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99762 ), #2100 ) ; +#90114 = STYLED_ITEM ( 'NONE', ( #65935 ), #87330 ) ; +#90115 = VECTOR ( 'NONE', #94442, 1000.000000000000000 ) ; +#90116 = VECTOR ( 'NONE', #73131, 1000.000000000000000 ) ; +#90117 = SURFACE_STYLE_USAGE ( .BOTH. , #50366 ) ; +#90118 = LINE ( 'NONE', #59030, #83221 ) ; +#90120 = ADVANCED_FACE ( 'NONE', ( #55194 ), #9119, .T. ) ; +#90119 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90121 = AXIS2_PLACEMENT_3D ( 'NONE', #66180, #19195, #20202 ) ; +#90122 = SURFACE_STYLE_USAGE ( .BOTH. , #42674 ) ; +#90123 = FACE_OUTER_BOUND ( 'NONE', #96323, .T. ) ; +#90124 = ORIENTED_EDGE ( 'NONE', *, *, #19469, .F. ) ; +#90125 = PRESENTATION_STYLE_ASSIGNMENT (( #75315 ) ) ; +#90126 = VERTEX_POINT ( 'NONE', #16815 ) ; +#90127 = FACE_OUTER_BOUND ( 'NONE', #100291, .T. ) ; +#90128 = CARTESIAN_POINT ( 'NONE', ( -1.094250269889780025, -1.238505293396390039, 0.8100000000000000533 ) ) ; +#90129 = DIRECTION ( 'NONE', ( 0.8365291563254616536, -0.5479224129540708477, 0.000000000000000000 ) ) ; +#90130 = FACE_OUTER_BOUND ( 'NONE', #55838, .T. ) ; +#90131 = LINE ( 'NONE', #94390, #60502 ) ; +#90132 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90133 = CARTESIAN_POINT ( 'NONE', ( 0.9699999999999999734, 0.1200000000000000094, -0.6500000000000000222 ) ) ; +#90134 = VERTEX_POINT ( 'NONE', #15298 ) ; +#90135 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999999762, 0.8991599999999999593 ) ) ; +#90136 = FACE_OUTER_BOUND ( 'NONE', #13182, .T. ) ; +#90137 = ORIENTED_CLOSED_SHELL ( 'NONE', *, #16019, .F. ); +#90140 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#90139 = CARTESIAN_POINT ( 'NONE', ( 4.479999999999999538, -8.400000000000000355, -11.91999999999999993 ) ) ; +#90138 = DIRECTION ( 'NONE', ( 0.7071060119555140355, 0.7071075504167442238, 0.000000000000000000 ) ) ; +#90141 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90142 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92898 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60714, #37719, #22379 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90143 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90144 = ORIENTED_EDGE ( 'NONE', *, *, #24450, .F. ) ; +#90145 = EDGE_CURVE ( 'NONE', #81565, #50603, #47489, .T. ) ; +#90146 = FACE_OUTER_BOUND ( 'NONE', #78878, .T. ) ; +#90147 = SURFACE_SIDE_STYLE ('',( #27908 ) ) ; +#90148 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90149 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90150 = AXIS2_PLACEMENT_3D ( 'NONE', #95689, #26303, #27304 ) ; +#90151 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#90152 = LINE ( 'NONE', #11972, #22894 ) ; +#90153 = LINE ( 'NONE', #75846, #48496 ) ; +#90154 = VECTOR ( 'NONE', #74525, 1000.000000000000114 ) ; +#90155 = SURFACE_STYLE_USAGE ( .BOTH. , #19201 ) ; +#90156 = PRESENTATION_STYLE_ASSIGNMENT (( #13491 ) ) ; +#90157 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90158 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 3.435721000000000025, 0.8648700000000000276 ) ) ; +#90159 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90160 = LINE ( 'NONE', #49899, #11182 ) ; +#90161 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90162 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90163 = ADVANCED_FACE ( 'NONE', ( #24563 ), #1551, .T. ) ; +#90164 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90165 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90166 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70326, 'distance_accuracy_value', 'NONE'); +#90167 = FILL_AREA_STYLE ('',( #26913 ) ) ; +#90168 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#90169 = VECTOR ( 'NONE', #57072, 1000.000000000000114 ) ; +#90170 = SURFACE_STYLE_USAGE ( .BOTH. , #65703 ) ; +#90171 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#90173 = EDGE_CURVE ( 'NONE', #56519, #5154, #63844, .T. ) ; +#90172 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#90174 = FILL_AREA_STYLE_COLOUR ( '', #93209 ) ; +#90175 = ORIENTED_EDGE ( 'NONE', *, *, #95741, .T. ) ; +#90176 = PLANE ( 'NONE', #32440 ) ; +#90177 = SURFACE_SIDE_STYLE ('',( #42725 ) ) ; +#90178 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95405, 'distance_accuracy_value', 'NONE'); +#90180 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31516 ) ) ; +#90179 = FILL_AREA_STYLE ('',( #30380 ) ) ; +#90181 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #91769 ), #36344 ) ; +#90182 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91534, 'distance_accuracy_value', 'NONE'); +#90183 = AXIS2_PLACEMENT_3D ( 'NONE', #53007, #55023, #45290 ) ; +#90185 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.016666666666667052, 0.000000000000000000 ) ) ; +#90184 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000046185, -3.500000000000000444, 0.000000000000000000 ) ) ; +#90186 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, -3.500000000000000444, 0.000000000000000000 ) ) ; +#90187 = STYLED_ITEM ( 'NONE', ( #13204 ), #60518 ) ; +#90188 = EDGE_CURVE ( 'NONE', #42663, #29437, #17339, .T. ) ; +#90189 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29831 ), #98211 ) ; +#90190 = EDGE_CURVE ( 'NONE', #54706, #68705, #7589, .T. ) ; +#90191 = STYLED_ITEM ( 'NONE', ( #11123 ), #96817 ) ; +#90192 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90193 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90194 = VERTEX_POINT ( 'NONE', #71998 ) ; +#90195 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90196 = ORIENTED_EDGE ( 'NONE', *, *, #66232, .T. ) ; +#90197 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#90198 = EDGE_CURVE ( 'NONE', #64233, #31325, #2052, .T. ) ; +#90199 = EDGE_CURVE ( 'NONE', #12979, #59108, #65846, .T. ) ; +#90200 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67181, 'distance_accuracy_value', 'NONE'); +#90201 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #57679 ), #95059 ) ; +#90202 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31864, 'distance_accuracy_value', 'NONE'); +#90203 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#90204 = ORIENTED_EDGE ( 'NONE', *, *, #51102, .T. ) ; +#90205 = ORIENTED_EDGE ( 'NONE', *, *, #72299, .F. ) ; +#90206 = EDGE_CURVE ( 'NONE', #92656, #44343, #72479, .T. ) ; +#90207 = PLANE ( 'NONE', #29582 ) ; +#90208 = AXIS2_PLACEMENT_3D ( 'NONE', #57462, #48294, #27313 ) ; +#90209 = EDGE_LOOP ( 'NONE', ( #83818, #94636, #52209, #34535 ) ) ; +#90210 = CARTESIAN_POINT ( 'NONE', ( 1.823014099396639942, -1.319025261726090026, 0.8100000000000000533 ) ) ; +#90211 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #26479, #20292, #51481, #34154 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#90212 = PRESENTATION_STYLE_ASSIGNMENT (( #4435 ) ) ; +#90213 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, 0.6999999999999989564, 0.1829999999999789573 ) ) ; +#90214 = FILL_AREA_STYLE_COLOUR ( '', #95308 ) ; +#90215 = EDGE_CURVE ( 'NONE', #98905, #54706, #42865, .T. ) ; +#90216 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #63258, #80166 ) ; +#90218 = ORIENTED_EDGE ( 'NONE', *, *, #99985, .T. ) ; +#90217 = ORIENTED_EDGE ( 'NONE', *, *, #53237, .T. ) ; +#90219 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77165 ) ) ; +#90220 = VERTEX_POINT ( 'NONE', #27056 ) ; +#90221 = ORIENTED_EDGE ( 'NONE', *, *, #36755, .F. ) ; +#90222 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90223 = LINE ( 'NONE', #67727, #13160 ) ; +#90224 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90225 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90226 = VERTEX_POINT ( 'NONE', #25548 ) ; +#90227 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3796 ) ) ; +#90228 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000013115, -0.2500000000000000000 ) ) ; +#90229 = DIRECTION ( 'NONE', ( -0.3387340427540269094, 0.000000000000000000, -0.9408821649279537347 ) ) ; +#90230 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56012 ) ) ; +#90231 = CARTESIAN_POINT ( 'NONE', ( -1.272737459667760085, -0.9076590548536880299, 0.8100000000000000533 ) ) ; +#90232 = ORIENTED_EDGE ( 'NONE', *, *, #90188, .T. ) ; +#90233 = LINE ( 'NONE', #20279, #34037 ) ; +#90234 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67415 ) ) ; +#90235 = EDGE_LOOP ( 'NONE', ( #86998, #100900, #13913, #3958 ) ) ; +#90236 = ORIENTED_EDGE ( 'NONE', *, *, #93213, .F. ) ; +#90237 = CARTESIAN_POINT ( 'NONE', ( 1.055638970329410009, -1.181386160465649926, 0.8100000000000000533 ) ) ; +#90238 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90239 = SURFACE_STYLE_USAGE ( .BOTH. , #11546 ) ; +#90240 = EDGE_CURVE ( 'NONE', #11652, #43651, #34726, .T. ) ; +#90242 = ORIENTED_EDGE ( 'NONE', *, *, #25880, .T. ) ; +#90241 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90243 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90244 = EDGE_LOOP ( 'NONE', ( #88254, #48557, #68257, #93843 ) ) ; +#90245 = CYLINDRICAL_SURFACE ( 'NONE', #98691, 0.1999999999999996503 ) ; +#90246 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999901329, 0.4300000000264844191, 0.6499230724029858575 ) ) ; +#90247 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#90248 = ORIENTED_EDGE ( 'NONE', *, *, #70613, .T. ) ; +#90250 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90249 = LINE ( 'NONE', #52468, #51483 ) ; +#90251 = LINE ( 'NONE', #20298, #13464 ) ; +#90252 = VERTEX_POINT ( 'NONE', #11116 ) ; +#90253 = EDGE_CURVE ( 'NONE', #65972, #59395, #50052, .T. ) ; +#90254 = VERTEX_POINT ( 'NONE', #42374 ) ; +#90255 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77194 ), #15201 ) ; +#90257 = FILL_AREA_STYLE ('',( #59167 ) ) ; +#90256 = CARTESIAN_POINT ( 'NONE', ( 0.9584415584415579836, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#90258 = FILL_AREA_STYLE_COLOUR ( '', #33534 ) ; +#90259 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90260 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88657 ) ) ; +#90261 = STYLED_ITEM ( 'NONE', ( #5593 ), #19016 ) ; +#90262 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#90263 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5451 ), #2242 ) ; +#90264 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#90265 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#90266 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90267 = ORIENTED_EDGE ( 'NONE', *, *, #74389, .F. ) ; +#90268 = ORIENTED_EDGE ( 'NONE', *, *, #39006, .F. ) ; +#90269 = FILL_AREA_STYLE_COLOUR ( '', #48927 ) ; +#90270 = SURFACE_STYLE_USAGE ( .BOTH. , #75453 ) ; +#90271 = CARTESIAN_POINT ( 'NONE', ( 1.367767600758680091, -1.205184960463220323, 0.8100000000000000533 ) ) ; +#90272 = PRESENTATION_STYLE_ASSIGNMENT (( #97401 ) ) ; +#90273 = FILL_AREA_STYLE ('',( #91277 ) ) ; +#90274 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90275 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#90276 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90277 = ORIENTED_EDGE ( 'NONE', *, *, #95647, .T. ) ; +#90278 = ADVANCED_FACE ( 'NONE', ( #57204 ), #4049, .T. ) ; +#90279 = FACE_OUTER_BOUND ( 'NONE', #1160, .T. ) ; +#90280 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90281 = AXIS2_PLACEMENT_3D ( 'NONE', #71118, #29783, #70607 ) ; +#90282 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.383333333333326642, 0.000000000000000000 ) ) ; +#90283 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000000, 3.099999999999970335, -0.02000000000000000042 ) ) ; +#90284 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#90285 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.000000000000000000 ) ) ; +#90286 = SURFACE_STYLE_USAGE ( .BOTH. , #57689 ) ; +#90287 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4600000000000000200, -0.2250000000000000333 ) ) ; +#90288 = FILL_AREA_STYLE ('',( #52019 ) ) ; +#90289 = FACE_OUTER_BOUND ( 'NONE', #34567, .T. ) ; +#90290 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5484 ) ) ; +#90291 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90292 = CARTESIAN_POINT ( 'NONE', ( 1.328634758872640154, -1.021599245672099920, 0.8300000000000004041 ) ) ; +#90293 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3926, 'distance_accuracy_value', 'NONE'); +#90294 = ORIENTED_EDGE ( 'NONE', *, *, #62975, .T. ) ; +#90295 = CARTESIAN_POINT ( 'NONE', ( -0.04154929258005846809, -1.501201143328667165, 0.8099999999994971223 ) ) ; +#90296 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90297 = ORIENTED_EDGE ( 'NONE', *, *, #36840, .F. ) ; +#90298 = LINE ( 'NONE', #65831, #62575 ) ; +#90299 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90300 = PRESENTATION_STYLE_ASSIGNMENT (( #19351 ) ) ; +#90302 = LINE ( 'NONE', #88425, #86749 ) ; +#90301 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88088 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6197, #45517, #75224 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90303 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999999734, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#90304 = LINE ( 'NONE', #91802, #83988 ) ; +#90306 = STYLED_ITEM ( 'NONE', ( #62967 ), #47769 ) ; +#90305 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#90307 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72373 ), #67416 ) ; +#90308 = LINE ( 'NONE', #53034, #90701 ) ; +#90309 = ORIENTED_EDGE ( 'NONE', *, *, #5170, .F. ) ; +#90310 = VECTOR ( 'NONE', #82014, 1000.000000000000000 ) ; +#90311 = VERTEX_POINT ( 'NONE', #49526 ) ; +#90312 = SURFACE_STYLE_USAGE ( .BOTH. , #98895 ) ; +#90313 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90314 = LINE ( 'NONE', #20875, #90452 ) ; +#90315 = FILL_AREA_STYLE_COLOUR ( '', #72267 ) ; +#90316 = EDGE_CURVE ( 'NONE', #31896, #79553, #41364, .T. ) ; +#90317 = FACE_OUTER_BOUND ( 'NONE', #13096, .T. ) ; +#90318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92814, 'distance_accuracy_value', 'NONE'); +#90319 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#90320 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11480, 'distance_accuracy_value', 'NONE'); +#90321 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90322 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90323 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65854 ) ) ; +#90324 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #65204, #9977, #41240, #40736 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#90325 = FACE_OUTER_BOUND ( 'NONE', #2594, .T. ) ; +#90326 = CARTESIAN_POINT ( 'NONE', ( 0.06819407704816833615, -1.118581631294313095, 0.8100000000000688871 ) ) ; +#90327 = ORIENTED_EDGE ( 'NONE', *, *, #25533, .F. ) ; +#90328 = ORIENTED_EDGE ( 'NONE', *, *, #16212, .F. ) ; +#90329 = VERTEX_POINT ( 'NONE', #33710 ) ; +#90330 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90331 = VECTOR ( 'NONE', #100193, 1000.000000000000000 ) ; +#90332 = FILL_AREA_STYLE ('',( #52551 ) ) ; +#90333 = DIRECTION ( 'NONE', ( -0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#90334 = EDGE_CURVE ( 'NONE', #58260, #56074, #95943, .T. ) ; +#90335 = AXIS2_PLACEMENT_3D ( 'NONE', #34988, #74268, #2818 ) ; +#90336 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90337 = CARTESIAN_POINT ( 'NONE', ( -0.3774237423761729882, -1.003781515188449935, 0.8299999999999999600 ) ) ; +#90338 = LINE ( 'NONE', #82689, #63713 ) ; +#90340 = VERTEX_POINT ( 'NONE', #10605 ) ; +#90339 = ORIENTED_EDGE ( 'NONE', *, *, #66229, .F. ) ; +#90341 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41458 ) ) ; +#90342 = VERTEX_POINT ( 'NONE', #41864 ) ; +#90343 = PLANE ( 'NONE', #76823 ) ; +#90344 = STYLED_ITEM ( 'NONE', ( #73687 ), #12025 ) ; +#90346 = DIRECTION ( 'NONE', ( 0.7071064476869689530, 0.7071071146859689849, 0.000000000000000000 ) ) ; +#90345 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90347 = EDGE_LOOP ( 'NONE', ( #34780, #58987, #59212, #34262 ) ) ; +#90348 = VERTEX_POINT ( 'NONE', #18848 ) ; +#90349 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90350 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90351 = AXIS2_PLACEMENT_3D ( 'NONE', #15837, #92919, #23038 ) ; +#90353 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90352 = FACE_OUTER_BOUND ( 'NONE', #97854, .T. ) ; +#90354 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#90355 = ORIENTED_EDGE ( 'NONE', *, *, #33447, .F. ) ; +#90356 = VERTEX_POINT ( 'NONE', #81189 ) ; +#90357 = STYLED_ITEM ( 'NONE', ( #77926 ), #72158 ) ; +#90358 = EDGE_LOOP ( 'NONE', ( #68352, #11408, #69745, #75295 ) ) ; +#90359 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90360 = SURFACE_SIDE_STYLE ('',( #91860 ) ) ; +#90361 = ADVANCED_FACE ( 'NONE', ( #63176 ), #93739, .T. ) ; +#90362 = AXIS2_PLACEMENT_3D ( 'NONE', #4489, #44287, #83629 ) ; +#90364 = ORIENTED_EDGE ( 'NONE', *, *, #98928, .F. ) ; +#90363 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, 3.383333333333326642, 1.747825839084889375E-76 ) ) ; +#90365 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90366 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90367 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26846 ), #41487 ) ; +#90368 = ORIENTED_EDGE ( 'NONE', *, *, #51238, .F. ) ; +#90369 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.899999999999978817, -0.02000000000000560010 ) ) ; +#90370 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#90371 = ORIENTED_EDGE ( 'NONE', *, *, #9299, .F. ) ; +#90372 = EDGE_CURVE ( 'NONE', #26148, #69223, #9448, .T. ) ; +#90373 = ORIENTED_EDGE ( 'NONE', *, *, #67109, .T. ) ; +#90374 = LINE ( 'NONE', #27118, #49796 ) ; +#90375 = VECTOR ( 'NONE', #90403, 1000.000000000000114 ) ; +#90376 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75652 ), #18641 ) ; +#90377 = CARTESIAN_POINT ( 'NONE', ( -1.323820061220085220, -3.099999999999990319, 0.000000000000000000 ) ) ; +#90378 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3939 ), #13637 ) ; +#90379 = LINE ( 'NONE', #35797, #84628 ) ; +#90381 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90380 = FACE_OUTER_BOUND ( 'NONE', #34140, .T. ) ; +#90382 = CARTESIAN_POINT ( 'NONE', ( 1.512057002305370101, -1.084890943604200020, 0.8299999999999997380 ) ) ; +#90383 = VERTEX_POINT ( 'NONE', #56019 ) ; +#90384 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90385 = ORIENTED_EDGE ( 'NONE', *, *, #83974, .T. ) ; +#90386 = FACE_OUTER_BOUND ( 'NONE', #77669, .T. ) ; +#90387 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90388 = LINE ( 'NONE', #34800, #10567 ) ; +#90389 = VECTOR ( 'NONE', #18807, 1000.000000000000000 ) ; +#90390 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48063 ), #59473 ) ; +#90391 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999312, 0.2458578643762690252 ) ) ; +#90393 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.699999999999999734, 0.000000000000000000 ) ) ; +#90392 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 13.05000000000000071, 0.03429000000000000103 ) ) ; +#90395 = VECTOR ( 'NONE', #21481, 1000.000000000000000 ) ; +#90394 = FACE_OUTER_BOUND ( 'NONE', #69988, .T. ) ; +#90396 = FACE_OUTER_BOUND ( 'NONE', #90718, .T. ) ; +#90397 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90398 = FILL_AREA_STYLE_COLOUR ( '', #56037 ) ; +#90400 = VECTOR ( 'NONE', #4756, 1000.000000000000000 ) ; +#90399 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67569 ), #25285 ) ; +#90401 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#90402 = STYLED_ITEM ( 'NONE', ( #74357 ), #98646 ) ; +#90403 = DIRECTION ( 'NONE', ( -0.3516809254569038257, 0.000000000000000000, 0.9361199317767865402 ) ) ; +#90404 = PLANE ( 'NONE', #27773 ) ; +#90405 = STYLED_ITEM ( 'NONE', ( #18553 ), #61383 ) ; +#90406 = EDGE_CURVE ( 'NONE', #2575, #92420, #47318, .T. ) ; +#90407 = VECTOR ( 'NONE', #34863, 1000.000000000000000 ) ; +#90408 = ORIENTED_EDGE ( 'NONE', *, *, #19473, .F. ) ; +#90410 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#90409 = LINE ( 'NONE', #50146, #65224 ) ; +#90411 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90412 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7162 ) ) ; +#90413 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38283, 'distance_accuracy_value', 'NONE'); +#90414 = EDGE_LOOP ( 'NONE', ( #74119, #62482, #60454, #33229 ) ) ; +#90415 = CARTESIAN_POINT ( 'NONE', ( -1.114703706423270324, -1.444732071753930036, 0.8100000000000000533 ) ) ; +#90416 = EDGE_CURVE ( 'NONE', #97446, #68754, #23349, .T. ) ; +#90417 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549969999999999182, 0.8991599999999999593 ) ) ; +#90418 = ADVANCED_FACE ( 'NONE', ( #855 ), #39154, .T. ) ; +#90419 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90420 = LINE ( 'NONE', #60813, #68251 ) ; +#90421 = FILL_AREA_STYLE ('',( #6095 ) ) ; +#90422 = FACE_OUTER_BOUND ( 'NONE', #41675, .T. ) ; +#90423 = VECTOR ( 'NONE', #45834, 1000.000000000000000 ) ; +#90424 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90425 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90426 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14665 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42660, #59021, #61004 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90427 = PLANE ( 'NONE', #87198 ) ; +#90428 = ORIENTED_EDGE ( 'NONE', *, *, #29444, .F. ) ; +#90429 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90430 = STYLED_ITEM ( 'NONE', ( #93115 ), #71750 ) ; +#90431 = ORIENTED_EDGE ( 'NONE', *, *, #90199, .F. ) ; +#90432 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45715, 'distance_accuracy_value', 'NONE'); +#90433 = SURFACE_STYLE_FILL_AREA ( #21993 ) ; +#90434 = SURFACE_STYLE_USAGE ( .BOTH. , #4660 ) ; +#90435 = EDGE_CURVE ( 'NONE', #6047, #59380, #31496, .T. ) ; +#90436 = CARTESIAN_POINT ( 'NONE', ( 0.4672454768135664294, -1.231935758531040870, 0.8100000000000001643 ) ) ; +#90437 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90438 = STYLED_ITEM ( 'NONE', ( #69384 ), #53938 ) ; +#90439 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, 0.000000000000000000 ) ) ; +#90440 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#90441 = FILL_AREA_STYLE_COLOUR ( '', #46049 ) ; +#90442 = EDGE_LOOP ( 'NONE', ( #11933, #38608, #10616, #11242 ) ) ; +#90443 = LINE ( 'NONE', #91943, #92271 ) ; +#90444 = LINE ( 'NONE', #65974, #6325 ) ; +#90445 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90446 = ORIENTED_EDGE ( 'NONE', *, *, #19411, .T. ) ; +#90447 = CARTESIAN_POINT ( 'NONE', ( -1.293506493506490163, -1.057183441558440018, 0.8099999999999785150 ) ) ; +#90448 = STYLED_ITEM ( 'NONE', ( #58258 ), #82330 ) ; +#90449 = STYLED_ITEM ( 'NONE', ( #63689 ), #88612 ) ; +#90450 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90451 = ORIENTED_EDGE ( 'NONE', *, *, #86213, .T. ) ; +#90452 = VECTOR ( 'NONE', #83178, 1000.000000000000000 ) ; +#90453 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77392 ), #67616 ) ; +#90454 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90455 = ADVANCED_FACE ( 'NONE', ( #1367 ), #33414, .T. ) ; +#90456 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#90457 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90458 = STYLED_ITEM ( 'NONE', ( #96097 ), #77095 ) ; +#90459 = SURFACE_STYLE_FILL_AREA ( #82809 ) ; +#90460 = ORIENTED_EDGE ( 'NONE', *, *, #25968, .F. ) ; +#90461 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#90462 = ORIENTED_EDGE ( 'NONE', *, *, #88034, .T. ) ; +#90463 = PLANE ( 'NONE', #2003 ) ; +#90464 = VECTOR ( 'NONE', #76452, 1000.000000000000000 ) ; +#90465 = VECTOR ( 'NONE', #91060, 1000.000000000000000 ) ; +#90466 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34970 ), #72536 ) ; +#90467 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90468 = VERTEX_POINT ( 'NONE', #55399 ) ; +#90469 = ORIENTED_EDGE ( 'NONE', *, *, #283, .T. ) ; +#90472 = AXIS2_PLACEMENT_3D ( 'NONE', #67392, #13710, #44887 ) ; +#90471 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82405 ), #95400 ) ; +#90470 = SURFACE_STYLE_USAGE ( .BOTH. , #28688 ) ; +#90473 = LINE ( 'NONE', #81839, #92155 ) ; +#90474 = FILL_AREA_STYLE_COLOUR ( '', #8129 ) ; +#90475 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8299999999999999600 ) ) ; +#90476 = EDGE_CURVE ( 'NONE', #100489, #84177, #39041, .T. ) ; +#90478 = SURFACE_STYLE_FILL_AREA ( #44011 ) ; +#90477 = PRESENTATION_STYLE_ASSIGNMENT (( #52205 ) ) ; +#90479 = ORIENTED_EDGE ( 'NONE', *, *, #14069, .T. ) ; +#90480 = ORIENTED_EDGE ( 'NONE', *, *, #36956, .T. ) ; +#90481 = ORIENTED_EDGE ( 'NONE', *, *, #31087, .T. ) ; +#90482 = AXIS2_PLACEMENT_3D ( 'NONE', #57060, #97297, #11464 ) ; +#90483 = SURFACE_STYLE_FILL_AREA ( #80843 ) ; +#90484 = EDGE_CURVE ( 'NONE', #15490, #73506, #31372, .T. ) ; +#90486 = EDGE_LOOP ( 'NONE', ( #67871, #7537, #58595, #87688 ) ) ; +#90485 = PRESENTATION_STYLE_ASSIGNMENT (( #50716 ) ) ; +#90487 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84543 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6057, #84725, #14743 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90488 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90489 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90490 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90491 = ORIENTED_EDGE ( 'NONE', *, *, #6738, .T. ) ; +#90492 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.500000000000000444, 0.000000000000000000 ) ) ; +#90493 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 8.958225000000000549, 0.8648700000000000276 ) ) ; +#90494 = ORIENTED_EDGE ( 'NONE', *, *, #60877, .F. ) ; +#90495 = ADVANCED_FACE ( 'NONE', ( #48734 ), #2267, .T. ) ; +#90496 = PRESENTATION_STYLE_ASSIGNMENT (( #27743 ) ) ; +#90497 = PRESENTATION_STYLE_ASSIGNMENT (( #35416 ) ) ; +#90498 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90499 = FILL_AREA_STYLE ('',( #20547 ) ) ; +#90500 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7466 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51719, #43025, #82847 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90501 = SURFACE_SIDE_STYLE ('',( #67995 ) ) ; +#90502 = CARTESIAN_POINT ( 'NONE', ( 1.823289888948260051, -1.336414498567920051, 0.8100000000000000533 ) ) ; +#90503 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90504 = FILL_AREA_STYLE_COLOUR ( '', #45770 ) ; +#90505 = STYLED_ITEM ( 'NONE', ( #29340 ), #29524 ) ; +#90506 = CARTESIAN_POINT ( 'NONE', ( -0.2259740259740259938, -1.091883116883120008, 0.8100000000000271427 ) ) ; +#90507 = EDGE_LOOP ( 'NONE', ( #75262, #25587, #3495, #45022 ) ) ; +#90508 = PLANE ( 'NONE', #94044 ) ; +#90509 = LINE ( 'NONE', #19563, #1003 ) ; +#90510 = VECTOR ( 'NONE', #22326, 1000.000000000000000 ) ; +#90511 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90513 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -1.500000000000000222, 0.1829999999999580573 ) ) ; +#90512 = FILL_AREA_STYLE ('',( #58417 ) ) ; +#90514 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90515 = DIRECTION ( 'NONE', ( 0.7071067816865476141, 0.7071067806865475314, -0.000000000000000000 ) ) ; +#90517 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #97192 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68345, #16208, #61229 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90516 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90518 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90519 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90520 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, -0.000000000000000000 ) ) ; +#90521 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90522 = ORIENTED_EDGE ( 'NONE', *, *, #47644, .T. ) ; +#90523 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12172 ) ) ; +#90524 = AXIS2_PLACEMENT_3D ( 'NONE', #45880, #84233, #28113 ) ; +#90525 = EDGE_CURVE ( 'NONE', #36176, #35369, #86513, .T. ) ; +#90526 = EDGE_CURVE ( 'NONE', #23560, #15372, #7796, .T. ) ; +#90527 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#90528 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90529 = ORIENTED_EDGE ( 'NONE', *, *, #65461, .F. ) ; +#90530 = LINE ( 'NONE', #20573, #57806 ) ; +#90532 = FACE_OUTER_BOUND ( 'NONE', #22403, .T. ) ; +#90531 = VECTOR ( 'NONE', #81219, 1000.000000000000000 ) ; +#90534 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#90533 = LINE ( 'NONE', #20574, #31118 ) ; +#90535 = FILL_AREA_STYLE_COLOUR ( '', #79821 ) ; +#90536 = FACE_OUTER_BOUND ( 'NONE', #65481, .T. ) ; +#90537 = EDGE_CURVE ( 'NONE', #141, #96487, #25264, .T. ) ; +#90538 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #31860 ) ) ; +#90539 = LINE ( 'NONE', #82398, #82856 ) ; +#90540 = VECTOR ( 'NONE', #93033, 1000.000000000000000 ) ; +#90541 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90542 = ORIENTED_EDGE ( 'NONE', *, *, #52503, .F. ) ; +#90543 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90544 = ADVANCED_FACE ( 'NONE', ( #23731 ), #54886, .T. ) ; +#90545 = EDGE_CURVE ( 'NONE', #605, #43736, #85377, .T. ) ; +#90548 = AXIS2_PLACEMENT_3D ( 'NONE', #69772, #53973, #46270 ) ; +#90547 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88956 ) ) ; +#90546 = SURFACE_SIDE_STYLE ('',( #28751 ) ) ; +#90549 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#90550 = CARTESIAN_POINT ( 'NONE', ( 1.068987518412940263, -1.485874691073119980, 0.8300000000000010703 ) ) ; +#90551 = SURFACE_STYLE_FILL_AREA ( #90035 ) ; +#90552 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90553 = EDGE_CURVE ( 'NONE', #76054, #7257, #4259, .T. ) ; +#90554 = FILL_AREA_STYLE_COLOUR ( '', #94712 ) ; +#90555 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90556 = STYLED_ITEM ( 'NONE', ( #74830 ), #98018 ) ; +#90557 = FACE_OUTER_BOUND ( 'NONE', #78196, .T. ) ; +#90558 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#90559 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61733, #92336, #56607, #80573 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#90560 = ORIENTED_EDGE ( 'NONE', *, *, #22921, .F. ) ; +#90561 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90562 = EDGE_LOOP ( 'NONE', ( #28604, #18066, #58154, #53826 ) ) ; +#90563 = STYLED_ITEM ( 'NONE', ( #96620 ), #3613 ) ; +#90564 = CARTESIAN_POINT ( 'NONE', ( 7.032512999999999792, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#90565 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8100000000000000533 ) ) ; +#90566 = SURFACE_STYLE_FILL_AREA ( #51275 ) ; +#90567 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#90568 = EDGE_CURVE ( 'NONE', #29659, #85194, #56910, .T. ) ; +#90569 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, 0.000000000000000000 ) ) ; +#90570 = CARTESIAN_POINT ( 'NONE', ( 1.837535075162280318, -0.9500768360162830106, 0.8299999999999999600 ) ) ; +#90571 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220025313, -2.700000000000000178, 0.000000000000000000 ) ) ; +#90572 = LINE ( 'NONE', #67078, #92837 ) ; +#90573 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90574 = ORIENTED_EDGE ( 'NONE', *, *, #76912, .F. ) ; +#90575 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#90576 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90577 = EDGE_CURVE ( 'NONE', #15739, #40880, #11823, .T. ) ; +#90578 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90579 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31779 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84809, #45974, #16348 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90580 = EDGE_LOOP ( 'NONE', ( #93176, #68658, #49185, #31415 ) ) ; +#90581 = VECTOR ( 'NONE', #46909, 1000.000000000000000 ) ; +#90582 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90583 = CARTESIAN_POINT ( 'NONE', ( 1.227431534468609975, -1.515241174392790047, 0.8299999999999994049 ) ) ; +#90584 = ADVANCED_FACE ( 'NONE', ( #66048 ), #81888, .T. ) ; +#90585 = AXIS2_PLACEMENT_3D ( 'NONE', #7528, #17285, #69892 ) ; +#90586 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90588 = EDGE_CURVE ( 'NONE', #83112, #11652, #96153, .T. ) ; +#90587 = CARTESIAN_POINT ( 'NONE', ( -1.313637677578630036, -1.335706927508150121, 0.8299999999999999600 ) ) ; +#90589 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#90590 = SURFACE_SIDE_STYLE ('',( #60476 ) ) ; +#90591 = ORIENTED_EDGE ( 'NONE', *, *, #25147, .T. ) ; +#90592 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90593 = VECTOR ( 'NONE', #32810, 1000.000000000000000 ) ; +#90594 = AXIS2_PLACEMENT_3D ( 'NONE', #60425, #68527, #29249 ) ; +#90595 = LINE ( 'NONE', #90084, #47016 ) ; +#90596 = PRODUCT_DEFINITION ( 'δ֪', '', #1361, #54539 ) ; +#90597 = ORIENTED_EDGE ( 'NONE', *, *, #58539, .F. ) ; +#90598 = STYLED_ITEM ( 'NONE', ( #61127 ), #82712 ) ; +#90599 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #42134 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73606, #19477, #82284 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90600 = SURFACE_STYLE_FILL_AREA ( #99173 ) ; +#90601 = LINE ( 'NONE', #74279, #53777 ) ; +#90602 = CARTESIAN_POINT ( 'NONE', ( -1.218842347006053650, -1.209605127971635996, 0.8099999999998336309 ) ) ; +#90603 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28644 ) ) ; +#90604 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.499999999999969802, -0.02000000000000000042 ) ) ; +#90605 = AXIS2_PLACEMENT_3D ( 'NONE', #22137, #32204, #82934 ) ; +#90606 = ORIENTED_EDGE ( 'NONE', *, *, #26328, .F. ) ; +#90607 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #76322 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23528, #77123, #24042 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90608 = SURFACE_STYLE_FILL_AREA ( #59514 ) ; +#90609 = PRODUCT ( 'ipx3.xtd', 'ipx3.xtd', '', ( #46359 ) ) ; +#90610 = ADVANCED_FACE ( 'NONE', ( #57404 ), #3760, .T. ) ; +#90611 = VECTOR ( 'NONE', #22027, 1000.000000000000114 ) ; +#90612 = EDGE_LOOP ( 'NONE', ( #15359, #45215, #38001, #97347 ) ) ; +#90613 = VERTEX_POINT ( 'NONE', #86254 ) ; +#90614 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73671, 'distance_accuracy_value', 'NONE'); +#90615 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#90617 = CARTESIAN_POINT ( 'NONE', ( -1.394603015216079989, -1.309512843728070086, 0.8100000000000000533 ) ) ; +#90616 = SURFACE_STYLE_USAGE ( .BOTH. , #74295 ) ; +#90618 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90619 = VECTOR ( 'NONE', #2688, 1000.000000000000114 ) ; +#90620 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90621 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.00000000000000000, 0.000000000000000000 ) ) ; +#90622 = SURFACE_STYLE_FILL_AREA ( #43629 ) ; +#90623 = ORIENTED_EDGE ( 'NONE', *, *, #32782, .T. ) ; +#90624 = EDGE_CURVE ( 'NONE', #50680, #12856, #16282, .T. ) ; +#90625 = CARTESIAN_POINT ( 'NONE', ( 1.268942880527089923, -1.510436674894549913, 0.8100000000000000533 ) ) ; +#90626 = LINE ( 'NONE', #28342, #3919 ) ; +#90627 = FILL_AREA_STYLE_COLOUR ( '', #12312 ) ; +#90628 = ORIENTED_EDGE ( 'NONE', *, *, #95179, .T. ) ; +#90629 = EDGE_CURVE ( 'NONE', #56519, #47020, #75226, .T. ) ; +#90631 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#90630 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#90632 = EDGE_LOOP ( 'NONE', ( #57764, #22311, #46989, #22128 ) ) ; +#90633 = AXIS2_PLACEMENT_3D ( 'NONE', #2621, #88893, #65385 ) ; +#90634 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61360 ), #41738 ) ; +#90636 = SURFACE_STYLE_FILL_AREA ( #59541 ) ; +#90635 = SURFACE_STYLE_USAGE ( .BOTH. , #67617 ) ; +#90637 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#90639 = ADVANCED_FACE ( 'NONE', ( #21577 ), #60428, .T. ) ; +#90638 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#90640 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72637 ) ) ; +#90641 = CARTESIAN_POINT ( 'NONE', ( -0.7539380133853422761, 1.377634075926969626, 0.8100000000000000533 ) ) ; +#90642 = ORIENTED_EDGE ( 'NONE', *, *, #84899, .F. ) ; +#90643 = FILL_AREA_STYLE ('',( #83487 ) ) ; +#90644 = VERTEX_POINT ( 'NONE', #69916 ) ; +#90646 = LINE ( 'NONE', #73822, #40877 ) ; +#90645 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90647 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90648 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#90649 = FACE_OUTER_BOUND ( 'NONE', #14955, .T. ) ; +#90650 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49387 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36900, #64652, #51734 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90651 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#90652 = EDGE_CURVE ( 'NONE', #21831, #77000, #24009, .T. ) ; +#90653 = ADVANCED_FACE ( 'NONE', ( #5212 ), #83383, .T. ) ; +#90654 = PLANE ( 'NONE', #14456 ) ; +#90655 = CARTESIAN_POINT ( 'NONE', ( 1.338207848547039891, -1.047446665233070062, 0.8299999999999999600 ) ) ; +#90656 = VERTEX_POINT ( 'NONE', #56671 ) ; +#90658 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51555 ), #66243 ) ; +#90657 = CARTESIAN_POINT ( 'NONE', ( 1.356532926677350037, -1.378727886756609955, 0.8299999999999994049 ) ) ; +#90659 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90660 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #100142, 'distance_accuracy_value', 'NONE'); +#90661 = LINE ( 'NONE', #98240, #10281 ) ; +#90662 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90663 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90664 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90665 = EDGE_LOOP ( 'NONE', ( #55766, #48709, #33355, #3789 ) ) ; +#90666 = VECTOR ( 'NONE', #55354, 1000.000000000000000 ) ; +#90667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #14008 ), #76008 ) ; +#90668 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90669 = STYLED_ITEM ( 'NONE', ( #35025 ), #82940 ) ; +#90670 = EDGE_CURVE ( 'NONE', #52613, #75510, #78171, .T. ) ; +#90671 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000777, 0.1400000000000000133 ) ) ; +#90672 = DIRECTION ( 'NONE', ( 0.7071067811865490160, -0.7071067811865461294, 0.000000000000000000 ) ) ; +#90673 = SURFACE_SIDE_STYLE ('',( #13481 ) ) ; +#90674 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#90676 = VECTOR ( 'NONE', #66363, 1000.000000000000000 ) ; +#90675 = PLANE ( 'NONE', #47480 ) ; +#90677 = EDGE_CURVE ( 'NONE', #51041, #98929, #39808, .T. ) ; +#90678 = CARTESIAN_POINT ( 'NONE', ( 6.572892999999999653, 10.59871300000000005, 0.8648700000000000276 ) ) ; +#90679 = LINE ( 'NONE', #83525, #67961 ) ; +#90680 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #24773, #32404, #30869, #39548 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#90681 = CARTESIAN_POINT ( 'NONE', ( 4.281867000000000090, 7.544011000000000244, 0.8991599999999999593 ) ) ; +#90682 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90683 = SURFACE_STYLE_USAGE ( .BOTH. , #58074 ) ; +#90684 = PRESENTATION_STYLE_ASSIGNMENT (( #84514 ) ) ; +#90685 = AXIS2_PLACEMENT_3D ( 'NONE', #6071, #28617, #37307 ) ; +#90686 = PRESENTATION_STYLE_ASSIGNMENT (( #98760 ) ) ; +#90687 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#90688 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90689 = CARTESIAN_POINT ( 'NONE', ( 0.1843824551312633342, -0.9969427909100427865, 0.8100000000000000533 ) ) ; +#90690 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402590496, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#90691 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90692 = SURFACE_SIDE_STYLE ('',( #30374 ) ) ; +#90693 = VERTEX_POINT ( 'NONE', #49491 ) ; +#90694 = PLANE ( 'NONE', #2991 ) ; +#90695 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.383333333333330195, 0.000000000000000000 ) ) ; +#90696 = AXIS2_PLACEMENT_3D ( 'NONE', #41551, #22306, #77428 ) ; +#90697 = EDGE_CURVE ( 'NONE', #82294, #68821, #48498, .T. ) ; +#90698 = SURFACE_STYLE_USAGE ( .BOTH. , #4896 ) ; +#90699 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#90700 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90701 = VECTOR ( 'NONE', #12125, 1000.000000000000114 ) ; +#90702 = STYLED_ITEM ( 'NONE', ( #55104 ), #13949 ) ; +#90704 = ADVANCED_FACE ( 'NONE', ( #1516 ), #80147, .T. ) ; +#90703 = SURFACE_STYLE_USAGE ( .BOTH. , #60587 ) ; +#90705 = EDGE_LOOP ( 'NONE', ( #100411, #14836, #100301, #84756 ) ) ; +#90707 = EDGE_CURVE ( 'NONE', #99398, #7959, #32155, .T. ) ; +#90706 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#90708 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79345 ), #33666 ) ; +#90709 = ORIENTED_EDGE ( 'NONE', *, *, #98599, .T. ) ; +#90710 = PLANE ( 'NONE', #96090 ) ; +#90711 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8100000000000000533 ) ) ; +#90712 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90713 = LINE ( 'NONE', #91212, #9409 ) ; +#90714 = VERTEX_POINT ( 'NONE', #25021 ) ; +#90715 = ORIENTED_EDGE ( 'NONE', *, *, #23712, .T. ) ; +#90716 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#90717 = DIRECTION ( 'NONE', ( 0.9999999999319444388, 1.166666699999935221E-05, 0.000000000000000000 ) ) ; +#90718 = EDGE_LOOP ( 'NONE', ( #48435, #99413, #37252, #7255, #97701, #82232 ) ) ; +#90719 = AXIS2_PLACEMENT_3D ( 'NONE', #50625, #98473, #74590 ) ; +#90720 = LINE ( 'NONE', #98305, #82594 ) ; +#90721 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #15902, #58257 ) ; +#90724 = VERTEX_POINT ( 'NONE', #71456 ) ; +#90723 = ORIENTED_EDGE ( 'NONE', *, *, #98481, .F. ) ; +#90722 = EDGE_CURVE ( 'NONE', #75133, #28438, #24527, .T. ) ; +#90725 = EDGE_LOOP ( 'NONE', ( #92931, #49291, #58120, #2721 ) ) ; +#90726 = ORIENTED_EDGE ( 'NONE', *, *, #274, .T. ) ; +#90727 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 1.149999999999999911, 0.000000000000000000 ) ) ; +#90728 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90729 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96180, 'distance_accuracy_value', 'NONE'); +#90730 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#90732 = CARTESIAN_POINT ( 'NONE', ( 1.353223433754789928, -0.9315058289328710384, 0.8299999999999999600 ) ) ; +#90731 = CARTESIAN_POINT ( 'NONE', ( 0.4491032436848350073, -0.9174134460922771517, 0.8100000000000000533 ) ) ; +#90733 = ADVANCED_FACE ( 'NONE', ( #56155 ), #28028, .T. ) ; +#90734 = VECTOR ( 'NONE', #11593, 1000.000000000000000 ) ; +#90735 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999500082 ) ) ; +#90736 = VERTEX_POINT ( 'NONE', #59195 ) ; +#90737 = STYLED_ITEM ( 'NONE', ( #37023 ), #78811 ) ; +#90738 = VECTOR ( 'NONE', #75396, 1000.000000000000000 ) ; +#90739 = EDGE_CURVE ( 'NONE', #10271, #74570, #35196, .T. ) ; +#90741 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#90740 = SURFACE_STYLE_USAGE ( .BOTH. , #4941 ) ; +#90742 = EDGE_LOOP ( 'NONE', ( #82388, #95493, #93595, #15852 ) ) ; +#90743 = EDGE_LOOP ( 'NONE', ( #72655, #99351, #71227, #32690, #41921, #37236 ) ) ; +#90744 = CARTESIAN_POINT ( 'NONE', ( 0.9819563994042010968, -1.066576130479129914, 0.8100000000000000533 ) ) ; +#90745 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55145 ) ) ; +#90747 = PRESENTATION_STYLE_ASSIGNMENT (( #14596 ) ) ; +#90746 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90748 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#90749 = AXIS2_PLACEMENT_3D ( 'NONE', #77976, #61674, #22857 ) ; +#90751 = ADVANCED_FACE ( 'NONE', ( #90798 ), #51529, .T. ) ; +#90750 = FILL_AREA_STYLE_COLOUR ( '', #91367 ) ; +#90753 = ORIENTED_EDGE ( 'NONE', *, *, #62634, .T. ) ; +#90752 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90754 = CARTESIAN_POINT ( 'NONE', ( 13.17837700000000112, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#90755 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, 0.2999999999999991562, -0.02000000000000000042 ) ) ; +#90756 = VECTOR ( 'NONE', #86138, 1000.000000000000000 ) ; +#90757 = SURFACE_STYLE_USAGE ( .BOTH. , #92237 ) ; +#90758 = PLANE ( 'NONE', #29426 ) ; +#90759 = EDGE_LOOP ( 'NONE', ( #17371, #97041, #1192, #27233 ) ) ; +#90761 = PRESENTATION_STYLE_ASSIGNMENT (( #76946 ) ) ; +#90760 = LINE ( 'NONE', #21306, #66334 ) ; +#90762 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#90763 = VERTEX_POINT ( 'NONE', #98855 ) ; +#90764 = EDGE_CURVE ( 'NONE', #36363, #89004, #29002, .T. ) ; +#90765 = ORIENTED_EDGE ( 'NONE', *, *, #86010, .F. ) ; +#90766 = CARTESIAN_POINT ( 'NONE', ( 0.5453269378142420187, -1.066140682755960301, 0.8299999999999992939 ) ) ; +#90767 = FILL_AREA_STYLE_COLOUR ( '', #1684 ) ; +#90768 = SURFACE_STYLE_USAGE ( .BOTH. , #44770 ) ; +#90769 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97294 ), #66353 ) ; +#90770 = VECTOR ( 'NONE', #89574, 1000.000000000000000 ) ; +#90771 = SURFACE_SIDE_STYLE ('',( #29963 ) ) ; +#90772 = CARTESIAN_POINT ( 'NONE', ( -0.5756493506493509660, -1.188311688311689984, 0.8100000000000000533 ) ) ; +#90773 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#90774 = STYLED_ITEM ( 'NONE', ( #34098 ), #5206 ) ; +#90775 = EDGE_CURVE ( 'NONE', #37139, #84321, #73483, .T. ) ; +#90777 = EDGE_CURVE ( 'NONE', #92470, #53326, #59934, .T. ) ; +#90776 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01500000000000000118, 0.2399999999999999911 ) ) ; +#90778 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90779 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46070, 'distance_accuracy_value', 'NONE'); +#90780 = VECTOR ( 'NONE', #16367, 1000.000000000000000 ) ; +#90781 = ORIENTED_EDGE ( 'NONE', *, *, #59672, .T. ) ; +#90782 = FACE_OUTER_BOUND ( 'NONE', #22541, .T. ) ; +#90783 = ORIENTED_EDGE ( 'NONE', *, *, #28914, .T. ) ; +#90784 = AXIS2_PLACEMENT_3D ( 'NONE', #49213, #88002, #3735 ) ; +#90785 = LINE ( 'NONE', #19831, #79909 ) ; +#90786 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1499999999999999667, -0.01999999999999999695 ) ) ; +#90787 = EDGE_CURVE ( 'NONE', #39313, #45870, #96917, .T. ) ; +#90788 = ADVANCED_FACE ( 'NONE', ( #12101 ), #6938, .F. ) ; +#90789 = CARTESIAN_POINT ( 'NONE', ( 1.352961788992439907, -1.196758459236680006, 0.8299999999999999600 ) ) ; +#90790 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85820 ), #50005 ) ; +#90791 = PRESENTATION_STYLE_ASSIGNMENT (( #20835 ) ) ; +#90792 = PLANE ( 'NONE', #78896 ) ; +#90793 = VERTEX_POINT ( 'NONE', #84135 ) ; +#90794 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#90795 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105604999999999727, 0.8991599999999999593 ) ) ; +#90796 = EDGE_CURVE ( 'NONE', #26194, #63998, #39169, .T. ) ; +#90797 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#90798 = FACE_OUTER_BOUND ( 'NONE', #70470, .T. ) ; +#90799 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #65826 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38216, #83682, #7979 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90800 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#90801 = VECTOR ( 'NONE', #24513, 1000.000000000000000 ) ; +#90802 = EDGE_CURVE ( 'NONE', #12458, #66007, #83647, .T. ) ; +#90803 = CARTESIAN_POINT ( 'NONE', ( 1.797750835596120256, -1.188470249711290228, 0.8299999999999999600 ) ) ; +#90804 = LINE ( 'NONE', #29007, #46447 ) ; +#90805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28838 ), #45131 ) ; +#90806 = FACE_OUTER_BOUND ( 'NONE', #40244, .T. ) ; +#90807 = CARTESIAN_POINT ( 'NONE', ( 6.084989000000001091, 2.261924000000000046, 0.8991599999999999593 ) ) ; +#90808 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90809 = FACE_OUTER_BOUND ( 'NONE', #70150, .T. ) ; +#90810 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89208 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16053, #79389, #48761 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90811 = ORIENTED_EDGE ( 'NONE', *, *, #3133, .T. ) ; +#90812 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#90813 = SURFACE_SIDE_STYLE ('',( #6474 ) ) ; +#90814 = CARTESIAN_POINT ( 'NONE', ( -1.229319102665805463, -1.429931027375499042, 0.8099999999996714273 ) ) ; +#90815 = VERTEX_POINT ( 'NONE', #14636 ) ; +#90816 = CYLINDRICAL_SURFACE ( 'NONE', #25043, 0.05000000000000012768 ) ; +#90818 = STYLED_ITEM ( 'NONE', ( #88175 ), #54938 ) ; +#90817 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90819 = PRESENTATION_STYLE_ASSIGNMENT (( #44817 ) ) ; +#90820 = CARTESIAN_POINT ( 'NONE', ( 1.383333333333333526, 3.099999999999969891, 0.000000000000000000 ) ) ; +#90821 = VECTOR ( 'NONE', #69191, 1000.000000000000000 ) ; +#90822 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#90823 = EDGE_LOOP ( 'NONE', ( #18516, #70250, #31343, #4577 ) ) ; +#90824 = STYLED_ITEM ( 'NONE', ( #50641 ), #62313 ) ; +#90825 = ADVANCED_FACE ( 'NONE', ( #31520 ), #46815, .T. ) ; +#90826 = SURFACE_STYLE_FILL_AREA ( #52043 ) ; +#90827 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90828 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90829 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66413 ), #95681 ) ; +#90830 = VECTOR ( 'NONE', #9375, 1000.000000000000000 ) ; +#90831 = PRESENTATION_STYLE_ASSIGNMENT (( #67330 ) ) ; +#90832 = LINE ( 'NONE', #67331, #4528 ) ; +#90833 = VECTOR ( 'NONE', #39850, 1000.000000000000000 ) ; +#90834 = LINE ( 'NONE', #83187, #51150 ) ; +#90835 = EDGE_CURVE ( 'NONE', #4524, #54706, #92756, .T. ) ; +#90836 = CLOSED_SHELL ( 'NONE', ( #96678, #88748, #18246, #81794, #64273, #8333 ) ) ; +#90837 = FACE_OUTER_BOUND ( 'NONE', #4500, .T. ) ; +#90839 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51718 ) ) ; +#90838 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#90840 = VERTEX_POINT ( 'NONE', #99355 ) ; +#90841 = ORIENTED_EDGE ( 'NONE', *, *, #97062, .F. ) ; +#90842 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90843 = ORIENTED_EDGE ( 'NONE', *, *, #9341, .T. ) ; +#90844 = FACE_OUTER_BOUND ( 'NONE', #559, .T. ) ; +#90845 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#90846 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.149999999999999911, 1.048695503451053346E-76 ) ) ; +#90847 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90848 = SURFACE_STYLE_USAGE ( .BOTH. , #21897 ) ; +#90849 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90850 = CARTESIAN_POINT ( 'NONE', ( -0.5276249439448480461, -0.9003793229264169806, 0.8100000000000000533 ) ) ; +#90851 = CARTESIAN_POINT ( 'NONE', ( -0.03214163119229276888, 0.5753100270687899753, 0.8100000000000001643 ) ) ; +#90852 = PLANE ( 'NONE', #23581 ) ; +#90855 = ORIENTED_EDGE ( 'NONE', *, *, #67575, .F. ) ; +#90854 = ORIENTED_EDGE ( 'NONE', *, *, #58979, .F. ) ; +#90853 = EDGE_CURVE ( 'NONE', #51059, #90252, #29508, .T. ) ; +#90856 = ORIENTED_EDGE ( 'NONE', *, *, #47571, .T. ) ; +#90857 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90858 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8054, 'distance_accuracy_value', 'NONE'); +#90859 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81077, 'distance_accuracy_value', 'NONE'); +#90860 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544767000000000223, 0.8991599999999999593 ) ) ; +#90861 = ORIENTED_EDGE ( 'NONE', *, *, #68757, .F. ) ; +#90863 = ADVANCED_FACE ( 'NONE', ( #37684 ), #29986, .F. ) ; +#90862 = ORIENTED_EDGE ( 'NONE', *, *, #14421, .F. ) ; +#90864 = DIRECTION ( 'NONE', ( -0.7071067811865455743, -0.7071067811865493491, 0.000000000000000000 ) ) ; +#90866 = LINE ( 'NONE', #97951, #23809 ) ; +#90865 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#90867 = CARTESIAN_POINT ( 'NONE', ( -0.5491071428571430157, -0.9000000000000001332, 0.8299999999999999600 ) ) ; +#90868 = ORIENTED_EDGE ( 'NONE', *, *, #17797, .F. ) ; +#90870 = ORIENTED_EDGE ( 'NONE', *, *, #33230, .F. ) ; +#90869 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58590 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73840, #69124, #60053 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90871 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90872 = ORIENTED_EDGE ( 'NONE', *, *, #66825, .T. ) ; +#90873 = FACE_OUTER_BOUND ( 'NONE', #11046, .T. ) ; +#90874 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90875 = EDGE_CURVE ( 'NONE', #47168, #91322, #48388, .T. ) ; +#90877 = VERTEX_POINT ( 'NONE', #23883 ) ; +#90876 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.1499999999999999667, -0.01999999999999999695 ) ) ; +#90878 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #20760 ), #56662 ) ; +#90879 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90880 = CARTESIAN_POINT ( 'NONE', ( 1.900854206603999952, -1.350767436372750208, 0.8099999999999996092 ) ) ; +#90881 = VERTEX_POINT ( 'NONE', #2400 ) ; +#90882 = CYLINDRICAL_SURFACE ( 'NONE', #67997, 0.05000000000000012768 ) ; +#90883 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90884 = ORIENTED_EDGE ( 'NONE', *, *, #88725, .T. ) ; +#90885 = EDGE_CURVE ( 'NONE', #99428, #40624, #47852, .T. ) ; +#90886 = ORIENTED_EDGE ( 'NONE', *, *, #87992, .F. ) ; +#90887 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.099999999999999867, 0.000000000000000000 ) ) ; +#90888 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90889 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90890 = FILL_AREA_STYLE_COLOUR ( '', #10415 ) ; +#90891 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100124 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93727, #32517, #100798 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90892 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8991599999999999593 ) ) ; +#90893 = FILL_AREA_STYLE ('',( #13717 ) ) ; +#90894 = EDGE_CURVE ( 'NONE', #46504, #329, #95722, .T. ) ; +#90895 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01500000000000000118, -0.2500000000000000000 ) ) ; +#90896 = LINE ( 'NONE', #27628, #58585 ) ; +#90897 = SURFACE_STYLE_USAGE ( .BOTH. , #66897 ) ; +#90898 = SURFACE_STYLE_FILL_AREA ( #67397 ) ; +#90899 = ORIENTED_EDGE ( 'NONE', *, *, #12631, .T. ) ; +#90900 = SURFACE_SIDE_STYLE ('',( #79217 ) ) ; +#90901 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90902 = STYLED_ITEM ( 'NONE', ( #28631 ), #62478 ) ; +#90903 = ORIENTED_EDGE ( 'NONE', *, *, #83973, .T. ) ; +#90904 = ADVANCED_FACE ( 'NONE', ( #94276 ), #8953, .T. ) ; +#90905 = EDGE_CURVE ( 'NONE', #49647, #75316, #1898, .T. ) ; +#90906 = CARTESIAN_POINT ( 'NONE', ( -0.2912322945111979755, -1.413990021526319918, 0.8100000000000000533 ) ) ; +#90907 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90908 = SURFACE_STYLE_FILL_AREA ( #82258 ) ; +#90909 = VECTOR ( 'NONE', #35734, 1000.000000000000114 ) ; +#90911 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90910 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000002289, 0.8991599999999999593 ) ) ; +#90912 = SURFACE_STYLE_USAGE ( .BOTH. , #82750 ) ; +#90913 = CARTESIAN_POINT ( 'NONE', ( 1.766025874245259919, -1.139163918933580266, 0.8100000000000000533 ) ) ; +#90914 = CLOSED_SHELL ( 'NONE', ( #75988, #37094, #28674, #93137, #72473, #29790, #24026 ) ) ; +#90915 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.633333333333333304, 0.000000000000000000 ) ) ; +#90916 = VECTOR ( 'NONE', #45658, 1000.000000000000000 ) ; +#90917 = AXIS2_PLACEMENT_3D ( 'NONE', #86812, #94444, #93911 ) ; +#90918 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#90919 = ADVANCED_FACE ( 'NONE', ( #95784 ), #40207, .T. ) ; +#90920 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90921 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#90922 = AXIS2_PLACEMENT_3D ( 'NONE', #29723, #69005, #7667 ) ; +#90923 = EDGE_CURVE ( 'NONE', #32802, #69748, #96793, .T. ) ; +#90924 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40426 ) ) ; +#90926 = LINE ( 'NONE', #29145, #55073 ) ; +#90925 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90927 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90928 = ORIENTED_EDGE ( 'NONE', *, *, #69961, .T. ) ; +#90929 = CARTESIAN_POINT ( 'NONE', ( -1.027917449215540069, -1.416724300735810127, 0.8100000000000000533 ) ) ; +#90930 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36683, 'distance_accuracy_value', 'NONE'); +#90931 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 11.87581999999999915, 0.8991599999999999593 ) ) ; +#90932 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90933 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90934 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90935 = CIRCLE ( 'NONE', #25727, 0.009999999999999998473 ) ; +#90936 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90937 = LINE ( 'NONE', #37336, #6408 ) ; +#90938 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90939 = CARTESIAN_POINT ( 'NONE', ( 8.043675000000000352, 10.75427700000000009, 0.8991599999999999593 ) ) ; +#90940 = AXIS2_PLACEMENT_3D ( 'NONE', #88648, #89161, #18681 ) ; +#90941 = ORIENTED_EDGE ( 'NONE', *, *, #42498, .F. ) ; +#90942 = EDGE_LOOP ( 'NONE', ( #32702, #66096, #19014, #28191 ) ) ; +#90943 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000004441, -0.2400000000000000189 ) ) ; +#90944 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44084, 'distance_accuracy_value', 'NONE'); +#90945 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87418, 'distance_accuracy_value', 'NONE'); +#90946 = FILL_AREA_STYLE ('',( #37346 ) ) ; +#90947 = FILL_AREA_STYLE ('',( #51159 ) ) ; +#90948 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 2.417486999999999941, 0.8991599999999999593 ) ) ; +#90949 = FILL_AREA_STYLE ('',( #67447 ) ) ; +#90950 = VECTOR ( 'NONE', #25770, 1000.000000000000000 ) ; +#90951 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999949818, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#90952 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#90953 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#90954 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90955 = EDGE_CURVE ( 'NONE', #88242, #69664, #3406, .T. ) ; +#90956 = EDGE_LOOP ( 'NONE', ( #100317, #44160, #16233, #67758 ) ) ; +#90957 = PLANE ( 'NONE', #74298 ) ; +#90958 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#90959 = VERTEX_POINT ( 'NONE', #83017 ) ; +#90960 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#90961 = CARTESIAN_POINT ( 'NONE', ( 5.540517000000001246, 3.725635000000000030, 0.8991599999999999593 ) ) ; +#90962 = STYLED_ITEM ( 'NONE', ( #77821 ), #79425 ) ; +#90963 = ORIENTED_EDGE ( 'NONE', *, *, #74471, .T. ) ; +#90964 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#90965 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #6130 ), #45296 ) ; +#90966 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#90967 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#90968 = CIRCLE ( 'NONE', #46921, 0.04999999999999969746 ) ; +#90969 = FACE_OUTER_BOUND ( 'NONE', #29949, .T. ) ; +#90970 = STYLED_ITEM ( 'NONE', ( #72340 ), #62794 ) ; +#90971 = VERTEX_POINT ( 'NONE', #89674 ) ; +#90972 = FILL_AREA_STYLE ('',( #20513 ) ) ; +#90973 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9407 ), #53517 ) ; +#90974 = VERTEX_POINT ( 'NONE', #12473 ) ; +#90975 = VECTOR ( 'NONE', #44349, 1000.000000000000000 ) ; +#90976 = FILL_AREA_STYLE ('',( #75646 ) ) ; +#90977 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73350 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19241, #25438, #12523 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#90978 = CARTESIAN_POINT ( 'NONE', ( 1.966666666666663454, 3.500000000000000000, 0.000000000000000000 ) ) ; +#90979 = CLOSED_SHELL ( 'NONE', ( #14870, #2246, #52598, #81559, #853, #52325 ) ) ; +#90980 = ORIENTED_EDGE ( 'NONE', *, *, #10219, .T. ) ; +#90982 = EDGE_CURVE ( 'NONE', #59269, #27567, #11969, .T. ) ; +#90981 = EDGE_LOOP ( 'NONE', ( #79235, #90110, #54841, #92180 ) ) ; +#90983 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25765 ) ) ; +#90984 = PRESENTATION_STYLE_ASSIGNMENT (( #91478 ) ) ; +#90985 = PRESENTATION_STYLE_ASSIGNMENT (( #35878 ) ) ; +#90986 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#90988 = ORIENTED_EDGE ( 'NONE', *, *, #5192, .T. ) ; +#90987 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90989 = ORIENTED_EDGE ( 'NONE', *, *, #79255, .T. ) ; +#90990 = VERTEX_POINT ( 'NONE', #11460 ) ; +#90991 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#90992 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#90995 = ORIENTED_EDGE ( 'NONE', *, *, #80782, .T. ) ; +#90994 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45327 ) ) ; +#90993 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#90996 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000007994, -3.149999999999979927, 0.000000000000000000 ) ) ; +#90997 = SURFACE_STYLE_USAGE ( .BOTH. , #36881 ) ; +#90998 = EDGE_LOOP ( 'NONE', ( #24287, #64109, #81955, #26343 ) ) ; +#90999 = CARTESIAN_POINT ( 'NONE', ( -0.05550563827964252045, -0.9724808743382648002, 0.8100000000002873790 ) ) ; +#91000 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#91001 = EDGE_LOOP ( 'NONE', ( #92801, #54489, #62283, #15306 ) ) ; +#91002 = ADVANCED_FACE ( 'NONE', ( #4877 ), #34572, .F. ) ; +#91003 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21104 ), #60059 ) ; +#91004 = CARTESIAN_POINT ( 'NONE', ( 3.924999999999999822, 0.2000000000000000111, -12.24500000000000099 ) ) ; +#91005 = PRESENTATION_STYLE_ASSIGNMENT (( #99069 ) ) ; +#91006 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91007 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #83286, .NOT_KNOWN. ) ; +#91008 = STYLED_ITEM ( 'NONE', ( #48054 ), #74683 ) ; +#91009 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, -0.2349999999999999867 ) ) ; +#91010 = FACE_OUTER_BOUND ( 'NONE', #30131, .T. ) ; +#91011 = CARTESIAN_POINT ( 'NONE', ( 1.496103896103889941, -1.314082792207790007, 0.8299999999999999600 ) ) ; +#91012 = ORIENTED_EDGE ( 'NONE', *, *, #33456, .F. ) ; +#91013 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77969 ) ) ; +#91014 = EDGE_CURVE ( 'NONE', #65881, #65434, #10967, .T. ) ; +#91015 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91016 = VECTOR ( 'NONE', #98276, 1000.000000000000000 ) ; +#91017 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55196 ) ) ; +#91019 = CARTESIAN_POINT ( 'NONE', ( 1.571641772371880075, -1.354501511147599979, 0.8300000000000009592 ) ) ; +#91018 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, -0.3000000000000001554, -0.02000000000000000042 ) ) ; +#91020 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, 3.500000000000000444, 0.000000000000000000 ) ) ; +#91021 = SURFACE_STYLE_USAGE ( .BOTH. , #92980 ) ; +#91022 = AXIS2_PLACEMENT_3D ( 'NONE', #18199, #33579, #81566 ) ; +#91023 = FILL_AREA_STYLE_COLOUR ( '', #36644 ) ; +#91024 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#91025 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20988 ) ) ; +#91026 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.008431457505076202924, 0.1458578643762690474 ) ) ; +#91027 = VERTEX_POINT ( 'NONE', #26896 ) ; +#91028 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#91029 = FACE_OUTER_BOUND ( 'NONE', #49824, .T. ) ; +#91030 = ADVANCED_FACE ( 'NONE', ( #35069, #81548 ), #73852, .T. ) ; +#91031 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91032 = AXIS2_PLACEMENT_3D ( 'NONE', #59288, #5077, #100907 ) ; +#91033 = ORIENTED_EDGE ( 'NONE', *, *, #30039, .T. ) ; +#91034 = LINE ( 'NONE', #5722, #34094 ) ; +#91035 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91036 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#91037 = LINE ( 'NONE', #78242, #11205 ) ; +#91038 = AXIS2_PLACEMENT_3D ( 'NONE', #49341, #82502, #34552 ) ; +#91039 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999829818 ) ) ; +#91040 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79700 ), #89445 ) ; +#91041 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91042 = CLOSED_SHELL ( 'NONE', ( #84506, #38259, #90018, #86743, #66702, #2263 ) ) ; +#91043 = VERTEX_POINT ( 'NONE', #14012 ) ; +#91044 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91045 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91046 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11602 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87306, #49531, #34230 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91047 = SURFACE_STYLE_FILL_AREA ( #84875 ) ; +#91048 = CARTESIAN_POINT ( 'NONE', ( 0.9776395701974860408, -1.395425853902759972, 0.8300000000000010703 ) ) ; +#91049 = PRESENTATION_STYLE_ASSIGNMENT (( #84388 ) ) ; +#91050 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 4.241823000000000121, 0.8991599999999999593 ) ) ; +#91051 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20484 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13091, #85118, #37181 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91052 = PLANE ( 'NONE', #86578 ) ; +#91053 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8648700000000000276 ) ) ; +#91054 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91055 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85736, 'distance_accuracy_value', 'NONE'); +#91056 = EDGE_CURVE ( 'NONE', #61247, #13660, #45669, .T. ) ; +#91057 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91058 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91059 = ORIENTED_EDGE ( 'NONE', *, *, #99442, .F. ) ; +#91060 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91061 = ORIENTED_EDGE ( 'NONE', *, *, #19240, .T. ) ; +#91062 = SURFACE_SIDE_STYLE ('',( #52283 ) ) ; +#91063 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #2072, 'distance_accuracy_value', 'NONE'); +#91064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38114, 'distance_accuracy_value', 'NONE'); +#91065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91066 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -2.500000000000000000, 0.000000000000000000 ) ) ; +#91067 = LINE ( 'NONE', #21118, #39659 ) ; +#91068 = CARTESIAN_POINT ( 'NONE', ( -0.9721805927153830407, -1.463531211619029992, 0.8299999999999981837 ) ) ; +#91069 = CARTESIAN_POINT ( 'NONE', ( 1.825861765333669950, -0.9394184040112200096, 0.8100000000000000533 ) ) ; +#91070 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91071 = CARTESIAN_POINT ( 'NONE', ( 9.507386958374977937, 5.557040958374940054, 0.8991599999999999593 ) ) ; +#91072 = ADVANCED_FACE ( 'NONE', ( #21713 ), #30881, .T. ) ; +#91073 = VERTEX_POINT ( 'NONE', #38057 ) ; +#91074 = FACE_OUTER_BOUND ( 'NONE', #83961, .T. ) ; +#91075 = SURFACE_STYLE_FILL_AREA ( #35978 ) ; +#91076 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41441, 'distance_accuracy_value', 'NONE'); +#91077 = PRESENTATION_STYLE_ASSIGNMENT (( #21630 ) ) ; +#91078 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91079 = AXIS2_PLACEMENT_3D ( 'NONE', #97311, #66208, #64695 ) ; +#91080 = AXIS2_PLACEMENT_3D ( 'NONE', #28954, #22292, #30424 ) ; +#91081 = ORIENTED_EDGE ( 'NONE', *, *, #30891, .T. ) ; +#91082 = LINE ( 'NONE', #21136, #3844 ) ; +#91083 = AXIS2_PLACEMENT_3D ( 'NONE', #100343, #5483, #29992 ) ; +#91084 = LINE ( 'NONE', #20626, #18080 ) ; +#91085 = FILL_AREA_STYLE ('',( #76761 ) ) ; +#91086 = LINE ( 'NONE', #37484, #39763 ) ; +#91087 = VERTEX_POINT ( 'NONE', #23249 ) ; +#91088 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79747 ), #11115 ) ; +#91089 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91901, 'distance_accuracy_value', 'NONE'); +#91090 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97550 ), #30714 ) ; +#91092 = FACE_OUTER_BOUND ( 'NONE', #22783, .T. ) ; +#91091 = AXIS2_PLACEMENT_3D ( 'NONE', #8575, #16301, #47991 ) ; +#91093 = FILL_AREA_STYLE ('',( #76262 ) ) ; +#91094 = LINE ( 'NONE', #27319, #24015 ) ; +#91095 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83010 ), #60165 ) ; +#91096 = ORIENTED_EDGE ( 'NONE', *, *, #8214, .T. ) ; +#91097 = PRESENTATION_STYLE_ASSIGNMENT (( #59993 ) ) ; +#91098 = PLANE ( 'NONE', #67370 ) ; +#91099 = VECTOR ( 'NONE', #3009, 1000.000000000000000 ) ; +#91100 = SURFACE_SIDE_STYLE ('',( #43128 ) ) ; +#91101 = FILL_AREA_STYLE ('',( #84930 ) ) ; +#91102 = ORIENTED_EDGE ( 'NONE', *, *, #72230, .F. ) ; +#91103 = ADVANCED_FACE ( 'NONE', ( #22735 ), #53374, .T. ) ; +#91104 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79040 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #46787, #45264, #45757 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91105 = EDGE_LOOP ( 'NONE', ( #59123, #92727, #92790, #30526 ) ) ; +#91107 = ORIENTED_EDGE ( 'NONE', *, *, #94325, .T. ) ; +#91106 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000444, 1.699999999999999734, -3.118622929693471946E-90 ) ) ; +#91108 = AXIS2_PLACEMENT_3D ( 'NONE', #58977, #83431, #20617 ) ; +#91109 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666633301, -1.699999999999999956, 0.000000000000000000 ) ) ; +#91110 = SURFACE_STYLE_FILL_AREA ( #43624 ) ; +#91111 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91112 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, -0.02000000000002515044 ) ) ; +#91113 = VECTOR ( 'NONE', #38150, 1000.000000000000000 ) ; +#91114 = ORIENTED_EDGE ( 'NONE', *, *, #99556, .F. ) ; +#91115 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#91116 = FILL_AREA_STYLE_COLOUR ( '', #64614 ) ; +#91117 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91118 = VERTEX_POINT ( 'NONE', #40587 ) ; +#91119 = EDGE_CURVE ( 'NONE', #16467, #98956, #24783, .T. ) ; +#91120 = PLANE ( 'NONE', #25331 ) ; +#91121 = EDGE_CURVE ( 'NONE', #1595, #64204, #31901, .T. ) ; +#91122 = SURFACE_STYLE_USAGE ( .BOTH. , #54337 ) ; +#91123 = CARTESIAN_POINT ( 'NONE', ( 6.127864000000000644, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#91124 = VERTEX_POINT ( 'NONE', #72215 ) ; +#91125 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72604 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86392, #47588, #99596 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91127 = FILL_AREA_STYLE_COLOUR ( '', #40471 ) ; +#91126 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#91128 = VERTEX_POINT ( 'NONE', #239 ) ; +#91129 = VECTOR ( 'NONE', #62458, 1000.000000000000000 ) ; +#91131 = LINE ( 'NONE', #5819, #50001 ) ; +#91130 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.499999999999960032, -0.02000000000000000042 ) ) ; +#91132 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91133 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000001332, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#91134 = AXIS2_PLACEMENT_3D ( 'NONE', #97922, #61213, #75997 ) ; +#91135 = EDGE_CURVE ( 'NONE', #97325, #14100, #32415, .T. ) ; +#91136 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91137 = ORIENTED_EDGE ( 'NONE', *, *, #83143, .F. ) ; +#91138 = PRESENTATION_STYLE_ASSIGNMENT (( #97743 ) ) ; +#91139 = ORIENTED_EDGE ( 'NONE', *, *, #52888, .F. ) ; +#91141 = PLANE ( 'NONE', #91500 ) ; +#91140 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#91142 = SURFACE_STYLE_USAGE ( .BOTH. , #13453 ) ; +#91143 = FILL_AREA_STYLE ('',( #60036 ) ) ; +#91144 = STYLED_ITEM ( 'NONE', ( #33455 ), #32621 ) ; +#91145 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91146 = VECTOR ( 'NONE', #86087, 1000.000000000000000 ) ; +#91147 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#91148 = CARTESIAN_POINT ( 'NONE', ( 1.341536415582540220, -1.062017517080650064, 0.8299999999999999600 ) ) ; +#91149 = LINE ( 'NONE', #30858, #10289 ) ; +#91150 = EDGE_CURVE ( 'NONE', #58769, #46513, #33436, .T. ) ; +#91151 = VECTOR ( 'NONE', #30860, 1000.000000000000000 ) ; +#91152 = STYLED_ITEM ( 'NONE', ( #91663 ), #31951 ) ; +#91153 = ORIENTED_EDGE ( 'NONE', *, *, #22054, .F. ) ; +#91154 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#91155 = CARTESIAN_POINT ( 'NONE', ( 1.325329304031209965, -1.416724300735810127, 0.8299999999999994049 ) ) ; +#91157 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#91156 = SURFACE_SIDE_STYLE ('',( #28862 ) ) ; +#91158 = AXIS2_PLACEMENT_3D ( 'NONE', #71153, #9785, #65493 ) ; +#91159 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.8999999999999990230, 0.1829999999999829818 ) ) ; +#91160 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220055511, 0.09999999999999988065, -0.02000000000000000042 ) ) ; +#91161 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71573 ), #37393 ) ; +#91162 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.01000000000000001235, -0.2349999999999999867 ) ) ; +#91163 = SURFACE_STYLE_FILL_AREA ( #92146 ) ; +#91164 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91166 = ORIENTED_EDGE ( 'NONE', *, *, #68059, .T. ) ; +#91165 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94423 ) ) ; +#91167 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #65087 ), #75003 ) ; +#91168 = LINE ( 'NONE', #15008, #98292 ) ; +#91169 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.9833333333333340587, 0.000000000000000000 ) ) ; +#91170 = CARTESIAN_POINT ( 'NONE', ( 0.01532804002844260008, -1.344848644821849959, 0.8299999999999999600 ) ) ; +#91171 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91172 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91173 = STYLED_ITEM ( 'NONE', ( #2274 ), #80335 ) ; +#91174 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91175 = SURFACE_STYLE_FILL_AREA ( #6345 ) ; +#91176 = PRESENTATION_STYLE_ASSIGNMENT (( #60074 ) ) ; +#91177 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#91178 = PLANE ( 'NONE', #80071 ) ; +#91179 = ADVANCED_FACE ( 'NONE', ( #63067 ), #95666, .T. ) ; +#91180 = LINE ( 'NONE', #21232, #9403 ) ; +#91181 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91182 = DIRECTION ( 'NONE', ( -4.551691174664149710E-48, -1.355252715606880049E-16, 1.000000000000000000 ) ) ; +#91183 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#91184 = CARTESIAN_POINT ( 'NONE', ( 3.100999000000000283, 5.245913999999999966, 0.8991599999999999593 ) ) ; +#91185 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56053, 'distance_accuracy_value', 'NONE'); +#91186 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91187 = CARTESIAN_POINT ( 'NONE', ( 0.2486481275925916667, -0.9226012458933517957, 0.8100000000000000533 ) ) ; +#91188 = FILL_AREA_STYLE ('',( #12998 ) ) ; +#91189 = FILL_AREA_STYLE ('',( #73376 ) ) ; +#91190 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10761 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2120, #49095, #65383 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91191 = FILL_AREA_STYLE ('',( #90174 ) ) ; +#91192 = EDGE_CURVE ( 'NONE', #13569, #91854, #79381, .T. ) ; +#91193 = VERTEX_POINT ( 'NONE', #95156 ) ; +#91194 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8648700000000000276 ) ) ; +#91195 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37332, 'distance_accuracy_value', 'NONE'); +#91196 = LINE ( 'NONE', #21241, #72242 ) ; +#91197 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17171, 'distance_accuracy_value', 'NONE'); +#91198 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.274473528905959955E-45, 1.175494350822289960E-30 ) ) ; +#91199 = STYLED_ITEM ( 'NONE', ( #36797 ), #51007 ) ; +#91200 = EDGE_CURVE ( 'NONE', #92365, #47747, #41093, .T. ) ; +#91201 = CARTESIAN_POINT ( 'NONE', ( -0.05398490405131480679, -0.9763607356531520676, 0.8300000000000002931 ) ) ; +#91202 = VECTOR ( 'NONE', #81437, 1000.000000000000000 ) ; +#91203 = EDGE_LOOP ( 'NONE', ( #84401, #58372, #39349, #3980 ) ) ; +#91205 = EDGE_CURVE ( 'NONE', #22415, #65057, #48755, .T. ) ; +#91204 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#91206 = VERTEX_POINT ( 'NONE', #9841 ) ; +#91207 = FILL_AREA_STYLE ('',( #21755 ) ) ; +#91208 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34179 ), #60269 ) ; +#91209 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91210 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78964, 'distance_accuracy_value', 'NONE'); +#91211 = CARTESIAN_POINT ( 'NONE', ( 0.01310978785461489916, -1.357122040133029950, 0.8300000000000006262 ) ) ; +#91212 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000003147, 0.2500000000000000000 ) ) ; +#91213 = ORIENTED_EDGE ( 'NONE', *, *, #99156, .F. ) ; +#91214 = ORIENTED_EDGE ( 'NONE', *, *, #700, .F. ) ; +#91215 = VECTOR ( 'NONE', #15438, 1000.000000000000000 ) ; +#91216 = ORIENTED_EDGE ( 'NONE', *, *, #38828, .F. ) ; +#91217 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91218 = STYLED_ITEM ( 'NONE', ( #89515 ), #75564 ) ; +#91219 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91220 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#91221 = EDGE_CURVE ( 'NONE', #7273, #96473, #18053, .T. ) ; +#91222 = ADVANCED_FACE ( 'NONE', ( #70693 ), #80396, .T. ) ; +#91223 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69920 ), #78192 ) ; +#91224 = SURFACE_STYLE_USAGE ( .BOTH. , #52435 ) ; +#91226 = ORIENTED_EDGE ( 'NONE', *, *, #67456, .F. ) ; +#91225 = EDGE_LOOP ( 'NONE', ( #15818, #79446, #35976, #98454 ) ) ; +#91227 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23570, #99063, #54737 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91228 = EDGE_LOOP ( 'NONE', ( #62255, #57751, #55626, #91594 ) ) ; +#91229 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91230 = STYLED_ITEM ( 'NONE', ( #8719 ), #92225 ) ; +#91232 = CARTESIAN_POINT ( 'NONE', ( 1.391117489400210072, -0.9747981717974689708, 0.8100000000000000533 ) ) ; +#91231 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91233 = EDGE_CURVE ( 'NONE', #99206, #23833, #67056, .T. ) ; +#91234 = STYLED_ITEM ( 'NONE', ( #4809 ), #6462 ) ; +#91235 = EDGE_CURVE ( 'NONE', #66903, #78858, #2779, .T. ) ; +#91236 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51289 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #67526, #100082, #84377 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91237 = CARTESIAN_POINT ( 'NONE', ( -1.367367192634590056, -1.017871276266119951, 0.8100000000000000533 ) ) ; +#91238 = ORIENTED_EDGE ( 'NONE', *, *, #52617, .F. ) ; +#91239 = PRESENTATION_STYLE_ASSIGNMENT (( #61633 ) ) ; +#91240 = ORIENTED_EDGE ( 'NONE', *, *, #76804, .F. ) ; +#91241 = ORIENTED_EDGE ( 'NONE', *, *, #83549, .F. ) ; +#91242 = PRESENTATION_STYLE_ASSIGNMENT (( #61133 ) ) ; +#91243 = PLANE ( 'NONE', #69025 ) ; +#91244 = VECTOR ( 'NONE', #78836, 1000.000000000000000 ) ; +#91245 = CARTESIAN_POINT ( 'NONE', ( 0.4360795454545450811, 0.6899999999999999467, 0.000000000000000000 ) ) ; +#91246 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #58114 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#91247 = LINE ( 'NONE', #37643, #32643 ) ; +#91249 = ORIENTED_EDGE ( 'NONE', *, *, #43828, .F. ) ; +#91248 = SURFACE_STYLE_USAGE ( .BOTH. , #48206 ) ; +#91250 = AXIS2_PLACEMENT_3D ( 'NONE', #5442, #50983, #74455 ) ; +#91251 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91252 = CARTESIAN_POINT ( 'NONE', ( 0.6431619866146579545, 0.5992840759269659756, 0.8100000000000000533 ) ) ; +#91253 = EDGE_CURVE ( 'NONE', #62227, #47482, #80532, .T. ) ; +#91254 = SURFACE_SIDE_STYLE ('',( #82608 ) ) ; +#91255 = ORIENTED_EDGE ( 'NONE', *, *, #72783, .T. ) ; +#91256 = FILL_AREA_STYLE ('',( #4475 ) ) ; +#91257 = ORIENTED_EDGE ( 'NONE', *, *, #47626, .T. ) ; +#91258 = ORIENTED_EDGE ( 'NONE', *, *, #54241, .T. ) ; +#91259 = SURFACE_STYLE_FILL_AREA ( #45265 ) ; +#91260 = SURFACE_SIDE_STYLE ('',( #37655 ) ) ; +#91262 = EDGE_CURVE ( 'NONE', #3032, #38282, #65543, .T. ) ; +#91261 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000009936, 3.099999999999980105, -0.02000000000000000042 ) ) ; +#91263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37496 ) ) ; +#91264 = SURFACE_SIDE_STYLE ('',( #28010 ) ) ; +#91265 = LINE ( 'NONE', #44282, #49547 ) ; +#91266 = LINE ( 'NONE', #45272, #78684 ) ; +#91267 = FILL_AREA_STYLE ('',( #69239 ) ) ; +#91268 = ADVANCED_FACE ( 'NONE', ( #3280 ), #51258, .F. ) ; +#91269 = ORIENTED_EDGE ( 'NONE', *, *, #84498, .F. ) ; +#91270 = SURFACE_STYLE_USAGE ( .BOTH. , #44779 ) ; +#91271 = ORIENTED_EDGE ( 'NONE', *, *, #55935, .T. ) ; +#91272 = EDGE_CURVE ( 'NONE', #13932, #8138, #40384, .T. ) ; +#91273 = CARTESIAN_POINT ( 'NONE', ( -0.03082045455219830504, -0.9939892240680031632, 0.8100000000000000533 ) ) ; +#91274 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33707 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2816, #49801, #41128 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91275 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91276 = FILL_AREA_STYLE ('',( #61672 ) ) ; +#91277 = FILL_AREA_STYLE_COLOUR ( '', #43524 ) ; +#91278 = SURFACE_SIDE_STYLE ('',( #84627 ) ) ; +#91279 = PRESENTATION_STYLE_ASSIGNMENT (( #67286 ) ) ; +#91280 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91281 = ORIENTED_EDGE ( 'NONE', *, *, #37709, .F. ) ; +#91282 = FILL_AREA_STYLE_COLOUR ( '', #33073 ) ; +#91283 = FACE_OUTER_BOUND ( 'NONE', #28842, .T. ) ; +#91284 = CARTESIAN_POINT ( 'NONE', ( 0.2777831599446540234, -0.9154070317056139938, 0.8299999999999999600 ) ) ; +#91285 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91286 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1661 ) ) ; +#91287 = SURFACE_SIDE_STYLE ('',( #89784 ) ) ; +#91288 = CARTESIAN_POINT ( 'NONE', ( -0.9399999999999999467, -9.880000000000000782, 0.2500000000000000000 ) ) ; +#91289 = FILL_AREA_STYLE_COLOUR ( '', #81001 ) ; +#91290 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91291 = VECTOR ( 'NONE', #85197, 1000.000000000000000 ) ; +#91292 = FACE_OUTER_BOUND ( 'NONE', #17747, .T. ) ; +#91293 = EDGE_CURVE ( 'NONE', #86833, #95078, #39097, .T. ) ; +#91294 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#91295 = LINE ( 'NONE', #84144, #25954 ) ; +#91296 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.005000000000000013115, 0.2400000000000000466 ) ) ; +#91297 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#91298 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #27331 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #88874, #11664, #65900 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91299 = STYLED_ITEM ( 'NONE', ( #58988 ), #85326 ) ; +#91300 = VECTOR ( 'NONE', #16817, 1000.000000000000000 ) ; +#91301 = CARTESIAN_POINT ( 'NONE', ( 1.199474818244760321, -0.9546485130184679813, 0.8299999999999995159 ) ) ; +#91302 = STYLED_ITEM ( 'NONE', ( #18546 ), #93916 ) ; +#91303 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65462, 'distance_accuracy_value', 'NONE'); +#91304 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34279 ), #45627 ) ; +#91305 = ORIENTED_EDGE ( 'NONE', *, *, #20636, .F. ) ; +#91306 = CARTESIAN_POINT ( 'NONE', ( 2.549999999999999822, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#91307 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000005773, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#91308 = ADVANCED_FACE ( 'NONE', ( #12861 ), #53746, .T. ) ; +#91309 = EDGE_CURVE ( 'NONE', #87098, #36781, #84877, .T. ) ; +#91310 = ORIENTED_EDGE ( 'NONE', *, *, #62109, .F. ) ; +#91311 = PRESENTATION_STYLE_ASSIGNMENT (( #30490 ) ) ; +#91312 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58775 ) ) ; +#91313 = PRESENTATION_STYLE_ASSIGNMENT (( #29032 ) ) ; +#91314 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86589, 'distance_accuracy_value', 'NONE'); +#91315 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24442 ), #63579 ) ; +#91316 = CARTESIAN_POINT ( 'NONE', ( 8.446725999999999956, 6.617701000000000278, 0.8648700000000000276 ) ) ; +#91317 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #88274 ) ) ; +#91318 = EDGE_CURVE ( 'NONE', #56923, #41651, #14897, .T. ) ; +#91319 = CARTESIAN_POINT ( 'NONE', ( 1.316543135457152403, -0.9014710040487492471, 0.8100000000000517897 ) ) ; +#91320 = SURFACE_STYLE_USAGE ( .BOTH. , #60217 ) ; +#91321 = STYLED_ITEM ( 'NONE', ( #51999 ), #64322 ) ; +#91322 = VERTEX_POINT ( 'NONE', #46036 ) ; +#91323 = PRESENTATION_STYLE_ASSIGNMENT (( #59734 ) ) ; +#91324 = EDGE_CURVE ( 'NONE', #9287, #42881, #5228, .T. ) ; +#91325 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220035527, -2.100000000000000089, 0.000000000000000000 ) ) ; +#91326 = VECTOR ( 'NONE', #90229, 1000.000000000000114 ) ; +#91327 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91328 = SURFACE_STYLE_USAGE ( .BOTH. , #43854 ) ; +#91329 = SURFACE_STYLE_FILL_AREA ( #84665 ) ; +#91330 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97420, 'distance_accuracy_value', 'NONE'); +#91331 = PRESENTATION_STYLE_ASSIGNMENT (( #29048 ) ) ; +#91332 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#91333 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8223, 'distance_accuracy_value', 'NONE'); +#91334 = FILL_AREA_STYLE_COLOUR ( '', #64808 ) ; +#91335 = ORIENTED_EDGE ( 'NONE', *, *, #84272, .T. ) ; +#91336 = ORIENTED_EDGE ( 'NONE', *, *, #91678, .T. ) ; +#91337 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3627, 'distance_accuracy_value', 'NONE'); +#91338 = ORIENTED_EDGE ( 'NONE', *, *, #49653, .F. ) ; +#91339 = CARTESIAN_POINT ( 'NONE', ( -0.7510755133853423970, 1.551634075926970002, 0.8100000000000000533 ) ) ; +#91340 = PRESENTATION_STYLE_ASSIGNMENT (( #67346 ) ) ; +#91341 = EDGE_CURVE ( 'NONE', #59760, #99161, #22102, .T. ) ; +#91343 = EDGE_CURVE ( 'NONE', #47472, #85330, #45051, .T. ) ; +#91342 = VECTOR ( 'NONE', #20465, 1000.000000000000000 ) ; +#91344 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999980016, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#91345 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91346 = CARTESIAN_POINT ( 'NONE', ( -0.4015774049763590758, -0.9593865114130070149, 0.8299999999999999600 ) ) ; +#91347 = CARTESIAN_POINT ( 'NONE', ( -1.204376861304429891, -0.9585643914498560569, 0.8100000000000000533 ) ) ; +#91348 = CARTESIAN_POINT ( 'NONE', ( 13.31975300000000040, 10.03041099999999908, 0.8648700000000000276 ) ) ; +#91350 = VERTEX_POINT ( 'NONE', #76723 ) ; +#91349 = ORIENTED_EDGE ( 'NONE', *, *, #91135, .F. ) ; +#91351 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91352 = ORIENTED_EDGE ( 'NONE', *, *, #97469, .F. ) ; +#91353 = SURFACE_STYLE_USAGE ( .BOTH. , #99892 ) ; +#91354 = LINE ( 'NONE', #68839, #2327 ) ; +#91355 = ORIENTED_EDGE ( 'NONE', *, *, #21284, .T. ) ; +#91356 = ORIENTED_EDGE ( 'NONE', *, *, #80273, .T. ) ; +#91357 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91358 = ADVANCED_FACE ( 'NONE', ( #60443 ), #36437, .F. ) ; +#91359 = FACE_OUTER_BOUND ( 'NONE', #46614, .T. ) ; +#91360 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51402 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36107, #97803, #83049 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91362 = LINE ( 'NONE', #37751, #30316 ) ; +#91361 = SURFACE_STYLE_FILL_AREA ( #6524 ) ; +#91363 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91364 = VERTEX_POINT ( 'NONE', #85893 ) ; +#91365 = VERTEX_POINT ( 'NONE', #94009 ) ; +#91366 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58760 ), #4901 ) ; +#91367 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#91368 = VECTOR ( 'NONE', #49493, 1000.000000000000114 ) ; +#91369 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#91370 = AXIS2_PLACEMENT_3D ( 'NONE', #26481, #12575, #57649 ) ; +#91371 = ORIENTED_EDGE ( 'NONE', *, *, #23119, .T. ) ; +#91372 = AXIS2_PLACEMENT_3D ( 'NONE', #16979, #41017, #1704 ) ; +#91373 = AXIS2_PLACEMENT_3D ( 'NONE', #94881, #56138, #80130 ) ; +#91374 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#91375 = LINE ( 'NONE', #61272, #50594 ) ; +#91376 = ORIENTED_EDGE ( 'NONE', *, *, #14971, .F. ) ; +#91377 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80040 ) ) ; +#91378 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91379 = CARTESIAN_POINT ( 'NONE', ( 3.999024500500175439, 5.267127499499825838, 0.8991599999999999593 ) ) ; +#91380 = VERTEX_POINT ( 'NONE', #9721 ) ; +#91381 = ORIENTED_EDGE ( 'NONE', *, *, #76223, .F. ) ; +#91382 = FILL_AREA_STYLE_COLOUR ( '', #11065 ) ; +#91383 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91384 = SURFACE_SIDE_STYLE ('',( #77567 ) ) ; +#91385 = STYLED_ITEM ( 'NONE', ( #51022 ), #80857 ) ; +#91386 = SURFACE_STYLE_FILL_AREA ( #35794 ) ; +#91387 = CYLINDRICAL_SURFACE ( 'NONE', #29829, 0.05000000000000012768 ) ; +#91388 = SURFACE_SIDE_STYLE ('',( #85729 ) ) ; +#91390 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#91389 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91391 = LINE ( 'NONE', #44894, #91511 ) ; +#91392 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#91393 = ORIENTED_EDGE ( 'NONE', *, *, #1542, .F. ) ; +#91394 = AXIS2_PLACEMENT_3D ( 'NONE', #54262, #87407, #39422 ) ; +#91395 = CARTESIAN_POINT ( 'NONE', ( -1.063637804261009956, -1.506193478032149979, 0.8100000000000000533 ) ) ; +#91396 = ORIENTED_EDGE ( 'NONE', *, *, #40287, .F. ) ; +#91397 = ADVANCED_FACE ( 'NONE', ( #71601 ), #95540, .T. ) ; +#91398 = AXIS2_PLACEMENT_3D ( 'NONE', #31718, #8144, #68981 ) ; +#91399 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#91400 = LINE ( 'NONE', #37303, #98793 ) ; +#91401 = CARTESIAN_POINT ( 'NONE', ( 8.100244000000000000, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#91402 = FILL_AREA_STYLE_COLOUR ( '', #97517 ) ; +#91403 = EDGE_CURVE ( 'NONE', #5584, #4091, #40975, .T. ) ; +#91405 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91404 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.1499999999999999667, -3.009265538105054994E-33 ) ) ; +#91406 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.45341999999999949, 0.8648700000000000276 ) ) ; +#91407 = DIRECTION ( 'NONE', ( -0.7071045084557405769, 0.7071090539100497452, 0.000000000000000000 ) ) ; +#91408 = FILL_AREA_STYLE_COLOUR ( '', #51143 ) ; +#91409 = SURFACE_STYLE_FILL_AREA ( #74208 ) ; +#91410 = SURFACE_STYLE_FILL_AREA ( #57402 ) ; +#91411 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 1.899999999999985922, 0.1829999999999920024 ) ) ; +#91412 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36041 ) ) ; +#91413 = SURFACE_STYLE_USAGE ( .BOTH. , #81773 ) ; +#91414 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91415 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21293 ) ) ; +#91416 = SURFACE_STYLE_FILL_AREA ( #27150 ) ; +#91417 = EDGE_CURVE ( 'NONE', #38123, #27802, #39944, .T. ) ; +#91419 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#91418 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 0.1200000000000000094, -0.6199999999999999956 ) ) ; +#91421 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81685 ), #78384 ) ; +#91420 = DIRECTION ( 'NONE', ( 1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#91422 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4559, 'distance_accuracy_value', 'NONE'); +#91423 = ORIENTED_EDGE ( 'NONE', *, *, #80294, .T. ) ; +#91424 = CARTESIAN_POINT ( 'NONE', ( -1.132903271161860070, -1.445215125000139933, 0.8100000000000000533 ) ) ; +#91425 = EDGE_CURVE ( 'NONE', #96032, #15748, #85387, .T. ) ; +#91426 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#91427 = SURFACE_STYLE_USAGE ( .BOTH. , #60321 ) ; +#91428 = FILL_AREA_STYLE ('',( #12747 ) ) ; +#91429 = PRESENTATION_STYLE_ASSIGNMENT (( #75120 ) ) ; +#91430 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40240 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36539, #84479, #13984 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91431 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#91432 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #54880, #73697 ), + ( #50257, #43052 ), + ( #80883, #26251 ), + ( #41070, #11318 ), + ( #34922, #25744 ), + ( #81396, #88516 ), + ( #10307, #58425 ), + ( #27261, #26753 ), + ( #10825, #2259 ), + ( #49744, #89027 ), + ( #11816, #74205 ), + ( #18555, #57923 ), + ( #56902, #96649 ), + ( #56409, #95134 ), + ( #87503, #81883 ), + ( #57397, #88015 ), + ( #41563, #42060 ), + ( #65040, #3250 ), + ( #17531, #4255 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06539851322094759889, 0.1302892112916909928, 0.1949613880993550097, 0.2597072667505109789, 0.3233315164440599965, 0.3849649931167459793, 0.4455304668157999970, 0.5050074906119650375, 0.5637094320295910066, 0.6217643038656159860, 0.6805306891948620374, 0.7399249246528789570, 0.8006913001071930269, 0.8636024226288889771, 0.9298736828390290476, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#91433 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91434 = VECTOR ( 'NONE', #67135, 1000.000000000000000 ) ; +#91435 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86562 ) ) ; +#91436 = FACE_OUTER_BOUND ( 'NONE', #55125, .T. ) ; +#91437 = EDGE_LOOP ( 'NONE', ( #68867, #64889, #4873, #1472 ) ) ; +#91438 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91439 = ORIENTED_EDGE ( 'NONE', *, *, #65753, .F. ) ; +#91440 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.004999999999999987094, -0.2458578643762690530 ) ) ; +#91441 = ADVANCED_FACE ( 'NONE', ( #32291 ), #71089, .T. ) ; +#91442 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26239 ), #16405 ) ; +#91443 = SURFACE_SIDE_STYLE ('',( #76120 ) ) ; +#91444 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#91445 = CARTESIAN_POINT ( 'NONE', ( 1.069461460811417464, -0.9133411585425684764, 0.8100000000000442402 ) ) ; +#91446 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91447 = FILL_AREA_STYLE ('',( #36331 ) ) ; +#91448 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91449 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#91450 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91451 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 3.383333333333323090, 0.000000000000000000 ) ) ; +#91452 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999995004, 0.8200000000000000622, 0.04999999999999997502 ) ) ; +#91453 = EDGE_CURVE ( 'NONE', #16858, #69965, #58325, .T. ) ; +#91454 = ORIENTED_EDGE ( 'NONE', *, *, #68766, .F. ) ; +#91455 = CARTESIAN_POINT ( 'NONE', ( 1.400000000000000133, 0.6600000000000000311, -0.8000000000000000444 ) ) ; +#91456 = SURFACE_STYLE_FILL_AREA ( #45949 ) ; +#91457 = VECTOR ( 'NONE', #73423, 1000.000000000000000 ) ; +#91458 = SURFACE_STYLE_USAGE ( .BOTH. , #89458 ) ; +#91459 = EDGE_LOOP ( 'NONE', ( #90765, #84296, #93540, #93330 ) ) ; +#91460 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.000000000000000000 ) ) ; +#91461 = VECTOR ( 'NONE', #36933, 1000.000000000000000 ) ; +#91462 = ORIENTED_EDGE ( 'NONE', *, *, #44892, .T. ) ; +#91463 = EDGE_CURVE ( 'NONE', #45825, #8544, #27167, .T. ) ; +#91464 = ADVANCED_FACE ( 'NONE', ( #73607 ), #88419, .T. ) ; +#91465 = FILL_AREA_STYLE ('',( #98048 ) ) ; +#91466 = FILL_AREA_STYLE_COLOUR ( '', #23515 ) ; +#91468 = EDGE_LOOP ( 'NONE', ( #20521, #59642, #71891, #66161, #48826, #4943 ) ) ; +#91467 = ORIENTED_EDGE ( 'NONE', *, *, #77168, .T. ) ; +#91469 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40989 ) ) ; +#91470 = EDGE_CURVE ( 'NONE', #9382, #1465, #46486, .T. ) ; +#91471 = EDGE_CURVE ( 'NONE', #98695, #36910, #19479, .T. ) ; +#91472 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91473 = ORIENTED_EDGE ( 'NONE', *, *, #81598, .F. ) ; +#91475 = CARTESIAN_POINT ( 'NONE', ( -0.4757128391191070560, -0.9978229697136190568, 0.8100000000000000533 ) ) ; +#91474 = PRESENTATION_STYLE_ASSIGNMENT (( #36862 ) ) ; +#91476 = ORIENTED_EDGE ( 'NONE', *, *, #98863, .F. ) ; +#91477 = ORIENTED_EDGE ( 'NONE', *, *, #76551, .F. ) ; +#91478 = SURFACE_STYLE_USAGE ( .BOTH. , #89966 ) ; +#91479 = SURFACE_SIDE_STYLE ('',( #51189 ) ) ; +#91480 = ADVANCED_FACE ( 'NONE', ( #11718 ), #74617, .T. ) ; +#91481 = CARTESIAN_POINT ( 'NONE', ( -0.5167618201584639470, -1.182153033657940000, 0.8299999999999999600 ) ) ; +#91482 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#91483 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#91484 = VERTEX_POINT ( 'NONE', #57823 ) ; +#91485 = ORIENTED_EDGE ( 'NONE', *, *, #70729, .F. ) ; +#91486 = AXIS2_PLACEMENT_3D ( 'NONE', #78533, #70892, #16722 ) ; +#91487 = VERTEX_POINT ( 'NONE', #50155 ) ; +#91488 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84914 ) ) ; +#91489 = EDGE_CURVE ( 'NONE', #6118, #80299, #11223, .T. ) ; +#91490 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4749999999999999778, 0.2400000000000000189 ) ) ; +#91491 = VECTOR ( 'NONE', #32961, 1000.000000000000000 ) ; +#91493 = ORIENTED_EDGE ( 'NONE', *, *, #89496, .F. ) ; +#91492 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 1.149999999999999911, 0.000000000000000000 ) ) ; +#91494 = PRESENTATION_STYLE_ASSIGNMENT (( #44994 ) ) ; +#91495 = SURFACE_SIDE_STYLE ('',( #98558 ) ) ; +#91496 = LINE ( 'NONE', #38885, #76566 ) ; +#91497 = ORIENTED_EDGE ( 'NONE', *, *, #97603, .F. ) ; +#91498 = VERTEX_POINT ( 'NONE', #14270 ) ; +#91499 = CARTESIAN_POINT ( 'NONE', ( 0.005160739295680100321, -0.9302426320460139841, 0.8299999999999988498 ) ) ; +#91500 = AXIS2_PLACEMENT_3D ( 'NONE', #52358, #93101, #83490 ) ; +#91501 = AXIS2_PLACEMENT_3D ( 'NONE', #4681, #6132, #99025 ) ; +#91502 = VERTEX_POINT ( 'NONE', #45423 ) ; +#91503 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70289 ) ) ; +#91504 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91505 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91507 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91506 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#91508 = SURFACE_STYLE_USAGE ( .BOTH. , #75688 ) ; +#91509 = ORIENTED_EDGE ( 'NONE', *, *, #26387, .F. ) ; +#91510 = ADVANCED_FACE ( 'NONE', ( #59329 ), #60324, .T. ) ; +#91511 = VECTOR ( 'NONE', #84240, 999.9999999999998863 ) ; +#91512 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #52024, #5490, #90295, #83155, #43834, #74997, #13118, #100834, #92297 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999998890, 0.3750000000000001665, 0.5000000000000004441, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#91513 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91514 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.7000000000000009548, 0.1829999999999659954 ) ) ; +#91515 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72000 ), #67029 ) ; +#91516 = PRESENTATION_STYLE_ASSIGNMENT (( #58415 ) ) ; +#91517 = EDGE_CURVE ( 'NONE', #80183, #93530, #99490, .T. ) ; +#91518 = CARTESIAN_POINT ( 'NONE', ( 1.688590486522010048, -1.445336647901249938, 0.8299999999999999600 ) ) ; +#91519 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000002623, 0.2500000000000000555, -0.8499999999999999778 ) ) ; +#91520 = PRESENTATION_STYLE_ASSIGNMENT (( #12331 ) ) ; +#91521 = STYLED_ITEM ( 'NONE', ( #64324 ), #20777 ) ; +#91522 = AXIS2_PLACEMENT_3D ( 'NONE', #7742, #83783, #6098 ) ; +#91523 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91524 = ORIENTED_EDGE ( 'NONE', *, *, #73257, .F. ) ; +#91525 = SURFACE_SIDE_STYLE ('',( #78105 ) ) ; +#91526 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91527 = PRESENTATION_STYLE_ASSIGNMENT (( #69016 ) ) ; +#91528 = PRESENTATION_STYLE_ASSIGNMENT (( #98113 ) ) ; +#91529 = EDGE_LOOP ( 'NONE', ( #29944, #70938, #29020 ) ) ; +#91531 = PLANE ( 'NONE', #85215 ) ; +#91530 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#91532 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91533 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91534 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91535 = FACE_OUTER_BOUND ( 'NONE', #94475, .T. ) ; +#91536 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#91537 = ORIENTED_EDGE ( 'NONE', *, *, #89368, .T. ) ; +#91538 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#91539 = EDGE_CURVE ( 'NONE', #26980, #94313, #90420, .T. ) ; +#91540 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#91541 = FILL_AREA_STYLE ('',( #83400 ) ) ; +#91542 = FILL_AREA_STYLE ('',( #76218 ) ) ; +#91543 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91544 = CARTESIAN_POINT ( 'NONE', ( 9.125548999999999467, 2.700330000000000563, 0.8991599999999999593 ) ) ; +#91545 = STYLED_ITEM ( 'NONE', ( #60564 ), #51879 ) ; +#91546 = FACE_OUTER_BOUND ( 'NONE', #72366, .T. ) ; +#91547 = SURFACE_SIDE_STYLE ('',( #20591 ) ) ; +#91548 = SURFACE_STYLE_FILL_AREA ( #4281 ) ; +#91549 = LINE ( 'NONE', #68047, #52956 ) ; +#91550 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85059 ) ) ; +#91551 = SURFACE_STYLE_FILL_AREA ( #60943 ) ; +#91552 = ORIENTED_EDGE ( 'NONE', *, *, #57403, .T. ) ; +#91553 = PRESENTATION_STYLE_ASSIGNMENT (( #21610 ) ) ; +#91554 = ORIENTED_EDGE ( 'NONE', *, *, #48445, .T. ) ; +#91555 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9360 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11266, #3691, #59378 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91556 = CARTESIAN_POINT ( 'NONE', ( 1.169384343503750090, -0.9551946040733080290, 0.8299999999999999600 ) ) ; +#91557 = LINE ( 'NONE', #36949, #8581 ) ; +#91558 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91559 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 15.15000000000000036, 0.000000000000000000 ) ) ; +#91560 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91561 = FILL_AREA_STYLE ('',( #52777 ) ) ; +#91562 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91563 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#91564 = ORIENTED_EDGE ( 'NONE', *, *, #17944, .F. ) ; +#91565 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8648700000000000276 ) ) ; +#91566 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762689975, -0.005000000000000000104, 0.2500000000000000000 ) ) ; +#91567 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24784 ), #1873 ) ; +#91568 = VECTOR ( 'NONE', #65228, 1000.000000000000000 ) ; +#91569 = SURFACE_STYLE_FILL_AREA ( #23152 ) ; +#91570 = EDGE_LOOP ( 'NONE', ( #77227, #42102, #78008, #59235 ) ) ; +#91571 = SURFACE_STYLE_USAGE ( .BOTH. , #81944 ) ; +#91572 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#91573 = CARTESIAN_POINT ( 'NONE', ( 1.429960467956949977, -1.401385721107119897, 0.8299999999999994049 ) ) ; +#91574 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33299 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39429, #53749, #62954 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91575 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91576 = PLANE ( 'NONE', #53040 ) ; +#91577 = CARTESIAN_POINT ( 'NONE', ( 10.10135624974991053, 3.676137249749912961, 0.8991599999999999593 ) ) ; +#91578 = EDGE_LOOP ( 'NONE', ( #85825, #42029, #75055, #31967 ) ) ; +#91579 = FILL_AREA_STYLE_COLOUR ( '', #10622 ) ; +#91580 = VECTOR ( 'NONE', #11906, 1000.000000000000000 ) ; +#91581 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#91582 = ADVANCED_FACE ( 'NONE', ( #91920 ), #43958, .T. ) ; +#91583 = FILL_AREA_STYLE ('',( #35992 ) ) ; +#91584 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91585 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91586 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34568 ), #47578 ) ; +#91587 = ORIENTED_EDGE ( 'NONE', *, *, #30948, .F. ) ; +#91588 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91589 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91590 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 14.25000000000000000, 0.000000000000000000 ) ) ; +#91591 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#91592 = VECTOR ( 'NONE', #21362, 1000.000000000000000 ) ; +#91593 = CARTESIAN_POINT ( 'NONE', ( 1.496184376687780260, -1.336216925617480067, 0.8300000000000001821 ) ) ; +#91594 = ORIENTED_EDGE ( 'NONE', *, *, #41270, .T. ) ; +#91595 = EDGE_CURVE ( 'NONE', #92443, #34637, #46282, .T. ) ; +#91596 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24820 ), #8355 ) ; +#91597 = ORIENTED_EDGE ( 'NONE', *, *, #83271, .T. ) ; +#91599 = VERTEX_POINT ( 'NONE', #39304 ) ; +#91598 = LINE ( 'NONE', #12417, #41171 ) ; +#91600 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #42419, 'distance_accuracy_value', 'NONE'); +#91601 = PLANE ( 'NONE', #84952 ) ; +#91602 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#91603 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91604 = ORIENTED_EDGE ( 'NONE', *, *, #73918, .F. ) ; +#91605 = FILL_AREA_STYLE_COLOUR ( '', #35798 ) ; +#91606 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#91607 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.5000000000000019984, 0.1829999999999659954 ) ) ; +#91608 = ORIENTED_EDGE ( 'NONE', *, *, #14495, .F. ) ; +#91609 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91610 = FILL_AREA_STYLE_COLOUR ( '', #36888 ) ; +#91611 = STYLED_ITEM ( 'NONE', ( #100710 ), #51921 ) ; +#91612 = ORIENTED_EDGE ( 'NONE', *, *, #46840, .T. ) ; +#91613 = ORIENTED_EDGE ( 'NONE', *, *, #41389, .F. ) ; +#91614 = AXIS2_PLACEMENT_3D ( 'NONE', #47538, #38878, #32234 ) ; +#91616 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.7099999999999999645, -1.100000000000000089 ) ) ; +#91615 = CARTESIAN_POINT ( 'NONE', ( 0.8852678571428560517, -1.227272727272729957, 0.8100000000000000533 ) ) ; +#91617 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91618 = CARTESIAN_POINT ( 'NONE', ( 0.1595320655217619954, -1.429044931969539967, 0.8299999999999982947 ) ) ; +#91619 = ORIENTED_EDGE ( 'NONE', *, *, #51835, .T. ) ; +#91620 = CARTESIAN_POINT ( 'NONE', ( -1.224646799147352653E-17, 0.8199999999999999512, 0.04999999999999997502 ) ) ; +#91621 = ORIENTED_EDGE ( 'NONE', *, *, #16789, .T. ) ; +#91622 = PRESENTATION_STYLE_ASSIGNMENT (( #60031 ) ) ; +#91623 = EDGE_CURVE ( 'NONE', #91484, #23563, #31157, .T. ) ; +#91624 = FACE_OUTER_BOUND ( 'NONE', #61616, .T. ) ; +#91625 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42746 ) ) ; +#91626 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #76992 ), #24853 ) ; +#91627 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#91628 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#91629 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100962 ) ; +#91630 = FACE_BOUND ( 'NONE', #50938, .T. ) ; +#91631 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 4.418599000000000387, 0.8648700000000000276 ) ) ; +#91633 = AXIS2_PLACEMENT_3D ( 'NONE', #81168, #87281, #96425 ) ; +#91632 = PLANE ( 'NONE', #5356 ) ; +#91634 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52526 ), #41103 ) ; +#91636 = ORIENTED_EDGE ( 'NONE', *, *, #89165, .F. ) ; +#91637 = SURFACE_STYLE_FILL_AREA ( #12459 ) ; +#91638 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4850000000000000422, -0.2399999999999999911 ) ) ; +#91639 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13267, 'distance_accuracy_value', 'NONE'); +#91640 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57513 ) ) ; +#91641 = LINE ( 'NONE', #84494, #87068 ) ; +#91642 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8991599999999999593 ) ) ; +#91643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91645 = PLANE ( 'NONE', #73939 ) ; +#91646 = VERTEX_POINT ( 'NONE', #24033 ) ; +#91647 = CIRCLE ( 'NONE', #54135, 0.09407705479135430870 ) ; +#91648 = SURFACE_STYLE_FILL_AREA ( #60061 ) ; +#91649 = EDGE_CURVE ( 'NONE', #73986, #95326, #34052, .T. ) ; +#91650 = PRESENTATION_STYLE_ASSIGNMENT (( #46165 ) ) ; +#91651 = CARTESIAN_POINT ( 'NONE', ( -0.05311487431094850248, -1.433486393616560051, 0.8299999999999999600 ) ) ; +#91652 = CARTESIAN_POINT ( 'NONE', ( 5.978922999999999988, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#91653 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91654 = VECTOR ( 'NONE', #74878, 1000.000000000000000 ) ; +#91655 = PRESENTATION_STYLE_ASSIGNMENT (( #67661 ) ) ; +#91656 = SURFACE_SIDE_STYLE ('',( #91175 ) ) ; +#91657 = EDGE_CURVE ( 'NONE', #71271, #46638, #94428, .T. ) ; +#91658 = PRESENTATION_STYLE_ASSIGNMENT (( #14523 ) ) ; +#91659 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#91660 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #2042 ), #77021 ) ; +#91661 = FILL_AREA_STYLE ('',( #7832 ) ) ; +#91662 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91663 = PRESENTATION_STYLE_ASSIGNMENT (( #37081 ) ) ; +#91664 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91665 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#91666 = VECTOR ( 'NONE', #67388, 1000.000000000000000 ) ; +#91667 = CARTESIAN_POINT ( 'NONE', ( 3.433338875124988476, 6.695483124875013736, 0.8991599999999999593 ) ) ; +#91668 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#91669 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#91670 = FILL_AREA_STYLE_COLOUR ( '', #81366 ) ; +#91671 = LINE ( 'NONE', #13504, #17695 ) ; +#91672 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91673 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91674 = CARTESIAN_POINT ( 'NONE', ( -0.9152290605710889926, -1.296821915455180108, 0.8100000000000000533 ) ) ; +#91675 = EDGE_CURVE ( 'NONE', #4845, #47472, #92887, .T. ) ; +#91676 = ORIENTED_EDGE ( 'NONE', *, *, #3928, .F. ) ; +#91677 = FILL_AREA_STYLE_COLOUR ( '', #7764 ) ; +#91678 = EDGE_CURVE ( 'NONE', #69209, #20645, #39831, .T. ) ; +#91679 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90944 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #44084, #75248, #11848 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91680 = FILL_AREA_STYLE_COLOUR ( '', #22597 ) ; +#91681 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.100000000000000533, -0.02000000000000000042 ) ) ; +#91682 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62419 ) ) ; +#91683 = SURFACE_SIDE_STYLE ('',( #60586 ) ) ; +#91684 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91685 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91686 = PLANE ( 'NONE', #50652 ) ; +#91687 = ORIENTED_EDGE ( 'NONE', *, *, #33977, .F. ) ; +#91688 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91689 = ADVANCED_FACE ( 'NONE', ( #24549 ), #40348, .F. ) ; +#91690 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#91691 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91692 = VECTOR ( 'NONE', #5736, 1000.000000000000000 ) ; +#91693 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#91694 = ORIENTED_EDGE ( 'NONE', *, *, #83514, .T. ) ; +#91695 = ORIENTED_EDGE ( 'NONE', *, *, #600, .F. ) ; +#91696 = VECTOR ( 'NONE', #55705, 1000.000000000000000 ) ; +#91697 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57190 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49178, #87970, #10770 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91698 = CARTESIAN_POINT ( 'NONE', ( 1.417810389965429962, -1.053930089500670020, 0.8299999999999998490 ) ) ; +#91699 = VERTEX_POINT ( 'NONE', #62317 ) ; +#91700 = FACE_OUTER_BOUND ( 'NONE', #61007, .T. ) ; +#91701 = CARTESIAN_POINT ( 'NONE', ( -0.1055551954118710001, -1.507644428662930025, 0.8299999999999999600 ) ) ; +#91702 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -1.100000000000000311, -0.02000000000000000042 ) ) ; +#91703 = FILL_AREA_STYLE ('',( #97341 ) ) ; +#91704 = CARTESIAN_POINT ( 'NONE', ( 0.4500000000000000666, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#91705 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91706 = VECTOR ( 'NONE', #76699, 1000.000000000000000 ) ; +#91707 = EDGE_CURVE ( 'NONE', #76830, #65675, #55182, .T. ) ; +#91708 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #55500, #78461 ) ; +#91709 = ORIENTED_EDGE ( 'NONE', *, *, #5015, .F. ) ; +#91710 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91711 = STYLED_ITEM ( 'NONE', ( #76968 ), #8946 ) ; +#91712 = ORIENTED_EDGE ( 'NONE', *, *, #62596, .T. ) ; +#91713 = LINE ( 'NONE', #52948, #62275 ) ; +#91714 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1504, 'distance_accuracy_value', 'NONE'); +#91715 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99707 ), #68815 ) ; +#91716 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91717 = VECTOR ( 'NONE', #6916, 1000.000000000000000 ) ; +#91718 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#91719 = SURFACE_STYLE_FILL_AREA ( #68231 ) ; +#91720 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#91721 = VECTOR ( 'NONE', #74384, 1000.000000000000114 ) ; +#91722 = EDGE_LOOP ( 'NONE', ( #74454, #53476, #28174, #92917 ) ) ; +#91723 = ORIENTED_EDGE ( 'NONE', *, *, #60266, .T. ) ; +#91724 = ORIENTED_EDGE ( 'NONE', *, *, #76296, .T. ) ; +#91725 = CARTESIAN_POINT ( 'NONE', ( 1.289721710971190038, -1.248384608377719918, 0.8100000000000000533 ) ) ; +#91726 = ADVANCED_FACE ( 'NONE', ( #1024 ), #93400, .F. ) ; +#91727 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#91728 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, 3.099999999999960121, -0.02000000000000000042 ) ) ; +#91729 = VECTOR ( 'NONE', #97966, 1000.000000000000000 ) ; +#91730 = ORIENTED_EDGE ( 'NONE', *, *, #22053, .F. ) ; +#91731 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91732 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#91733 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#91734 = ORIENTED_EDGE ( 'NONE', *, *, #93731, .F. ) ; +#91735 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#91736 = LINE ( 'NONE', #69763, #8640 ) ; +#91737 = ORIENTED_EDGE ( 'NONE', *, *, #94102, .F. ) ; +#91738 = ORIENTED_EDGE ( 'NONE', *, *, #40758, .T. ) ; +#91739 = EDGE_CURVE ( 'NONE', #49575, #3218, #64821, .T. ) ; +#91740 = CARTESIAN_POINT ( 'NONE', ( 0.9586437380306700451, -1.309512843728070086, 0.8100000000000000533 ) ) ; +#91741 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#91742 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 4.496381000000000405, 0.8991599999999999593 ) ) ; +#91743 = SURFACE_SIDE_STYLE ('',( #21315 ) ) ; +#91744 = CIRCLE ( 'NONE', #77109, 0.009999999999999998473 ) ; +#91745 = STYLED_ITEM ( 'NONE', ( #56058 ), #52190 ) ; +#91747 = STYLED_ITEM ( 'NONE', ( #91242 ), #47077 ) ; +#91746 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91748 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41292 ) ) ; +#91749 = CARTESIAN_POINT ( 'NONE', ( 8.969985124875011095, 9.983529124875014205, 0.8648700000000000276 ) ) ; +#91750 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.100000000000000089 ) ) ; +#91751 = ORIENTED_EDGE ( 'NONE', *, *, #14048, .T. ) ; +#91752 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91753 = ORIENTED_EDGE ( 'NONE', *, *, #56806, .F. ) ; +#91754 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49370 ) ) ; +#91755 = CARTESIAN_POINT ( 'NONE', ( 11.33879312487501245, 5.832812875124988139, 0.8648700000000000276 ) ) ; +#91756 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8100000000000000533 ) ) ; +#91757 = AXIS2_PLACEMENT_3D ( 'NONE', #98245, #5843, #83513 ) ; +#91758 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49452 ) ) ; +#91759 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91760 = VECTOR ( 'NONE', #19628, 1000.000000000000000 ) ; +#91761 = SURFACE_STYLE_FILL_AREA ( #69252 ) ; +#91762 = SURFACE_SIDE_STYLE ('',( #19838 ) ) ; +#91763 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #96282, #33548, #70811, #79500 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#91764 = ORIENTED_EDGE ( 'NONE', *, *, #20636, .T. ) ; +#91765 = CARTESIAN_POINT ( 'NONE', ( 1.694318181818180058, -0.9623376623376630468, 0.8199999999999999512 ) ) ; +#91766 = SURFACE_STYLE_FILL_AREA ( #85124 ) ; +#91768 = VECTOR ( 'NONE', #91217, 1000.000000000000000 ) ; +#91767 = SURFACE_STYLE_FILL_AREA ( #15137 ) ; +#91769 = STYLED_ITEM ( 'NONE', ( #97547 ), #18941 ) ; +#91770 = VECTOR ( 'NONE', #85249, 1000.000000000000000 ) ; +#91771 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#91772 = SURFACE_SIDE_STYLE ('',( #76463 ) ) ; +#91773 = SURFACE_SIDE_STYLE ('',( #84137 ) ) ; +#91775 = CARTESIAN_POINT ( 'NONE', ( 1.899701586460730285, -1.304291937284929981, 0.8299999999999999600 ) ) ; +#91774 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91776 = EDGE_CURVE ( 'NONE', #4926, #1768, #24482, .T. ) ; +#91777 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#91778 = STYLED_ITEM ( 'NONE', ( #35849 ), #36560 ) ; +#91779 = SURFACE_STYLE_USAGE ( .BOTH. , #60675 ) ; +#91780 = STYLED_ITEM ( 'NONE', ( #13257 ), #96724 ) ; +#91781 = FILL_AREA_STYLE ('',( #68785 ) ) ; +#91782 = PRESENTATION_STYLE_ASSIGNMENT (( #60677 ) ) ; +#91783 = PLANE ( 'NONE', #17969 ) ; +#91784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91785 = VECTOR ( 'NONE', #79590, 1000.000000000000000 ) ; +#91786 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91787 = CIRCLE ( 'NONE', #541, 0.1000000000000000056 ) ; +#91788 = CARTESIAN_POINT ( 'NONE', ( 1.306340380209440211, -0.9912247593444889482, 0.8299999999999995159 ) ) ; +#91789 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91790 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#91791 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, -3.099999999999989875, -0.02000000000000000042 ) ) ; +#91792 = CARTESIAN_POINT ( 'NONE', ( -1.036703617789598519, -0.9014710040487492471, 0.8100000000000607825 ) ) ; +#91793 = EDGE_CURVE ( 'NONE', #33704, #63028, #36085, .T. ) ; +#91794 = ORIENTED_EDGE ( 'NONE', *, *, #94434, .T. ) ; +#91795 = FACE_OUTER_BOUND ( 'NONE', #827, .T. ) ; +#91796 = SURFACE_STYLE_FILL_AREA ( #5979 ) ; +#91797 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#91798 = LINE ( 'NONE', #92774, #89282 ) ; +#91799 = EDGE_CURVE ( 'NONE', #26955, #42016, #82540, .T. ) ; +#91800 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55989 ) ) ; +#91801 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91802 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 1.149999999999999911, 0.000000000000000000 ) ) ; +#91803 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999267808, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#91804 = VERTEX_POINT ( 'NONE', #20223 ) ; +#91805 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#91806 = FILL_AREA_STYLE ('',( #92312 ) ) ; +#91807 = EDGE_CURVE ( 'NONE', #23290, #82605, #80670, .T. ) ; +#91808 = PLANE ( 'NONE', #6915 ) ; +#91809 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91810 = SURFACE_SIDE_STYLE ('',( #66841 ) ) ; +#91811 = SURFACE_STYLE_USAGE ( .BOTH. , #100859 ) ; +#91812 = ORIENTED_EDGE ( 'NONE', *, *, #82929, .T. ) ; +#91813 = EDGE_CURVE ( 'NONE', #60639, #65172, #12490, .T. ) ; +#91814 = ORIENTED_EDGE ( 'NONE', *, *, #70218, .T. ) ; +#91815 = VECTOR ( 'NONE', #47701, 1000.000000000000114 ) ; +#91816 = FACE_OUTER_BOUND ( 'NONE', #47146, .T. ) ; +#91817 = ORIENTED_EDGE ( 'NONE', *, *, #19713, .F. ) ; +#91818 = PLANE ( 'NONE', #2093 ) ; +#91819 = SURFACE_STYLE_USAGE ( .BOTH. , #54579 ) ; +#91820 = VECTOR ( 'NONE', #76758, 1000.000000000000000 ) ; +#91821 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91822 = FACE_OUTER_BOUND ( 'NONE', #47499, .T. ) ; +#91823 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91824 = ADVANCED_FACE ( 'NONE', ( #74867 ), #59595, .T. ) ; +#91825 = PRODUCT_CONTEXT ( 'NONE', #55359, 'mechanical' ) ; +#91826 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#91827 = CARTESIAN_POINT ( 'NONE', ( -0.03214163119229252602, 0.6230426933633675946, 0.8100000000000002753 ) ) ; +#91828 = EDGE_CURVE ( 'NONE', #20813, #99969, #83035, .T. ) ; +#91830 = EDGE_LOOP ( 'NONE', ( #94476, #78810, #47151, #66281 ) ) ; +#91829 = ORIENTED_EDGE ( 'NONE', *, *, #74256, .T. ) ; +#91831 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78797 ) ) ; +#91832 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#91833 = VERTEX_POINT ( 'NONE', #75364 ) ; +#91834 = CARTESIAN_POINT ( 'NONE', ( 1.560249861737120103, -0.9531265814360270205, 0.8099999999999981659 ) ) ; +#91835 = EDGE_CURVE ( 'NONE', #28576, #17126, #56113, .T. ) ; +#91837 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34818 ) ) ; +#91836 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32569, 'distance_accuracy_value', 'NONE'); +#91838 = VECTOR ( 'NONE', #12489, 1000.000000000000000 ) ; +#91840 = DIRECTION ( 'NONE', ( -0.7071067811865445751, 0.7071067811865504593, 0.000000000000000000 ) ) ; +#91839 = CARTESIAN_POINT ( 'NONE', ( -0.1525548447364439841, -1.164073081312986702, 0.8299999999999999600 ) ) ; +#91841 = VERTEX_POINT ( 'NONE', #5376 ) ; +#91842 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49534 ) ) ; +#91843 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #9109 ) ) ; +#91844 = EDGE_LOOP ( 'NONE', ( #91751, #30740, #65628, #69749 ) ) ; +#91845 = FACE_OUTER_BOUND ( 'NONE', #53332, .T. ) ; +#91846 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91847 = AXIS2_PLACEMENT_3D ( 'NONE', #30803, #78303, #17495 ) ; +#91848 = AXIS2_PLACEMENT_3D ( 'NONE', #28618, #22459, #21957 ) ; +#91849 = AXIS2_PLACEMENT_3D ( 'NONE', #1897, #64185, #80516 ) ; +#91850 = PRESENTATION_STYLE_ASSIGNMENT (( #20915 ) ) ; +#91852 = SURFACE_SIDE_STYLE ('',( #98436 ) ) ; +#91851 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155857000000000134, 0.8991599999999999593 ) ) ; +#91853 = CARTESIAN_POINT ( 'NONE', ( -0.4247119971151859796, -0.9357370515645540010, 0.8299999999999999600 ) ) ; +#91854 = VERTEX_POINT ( 'NONE', #33180 ) ; +#91855 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#91856 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #77200 ), #25072 ) ; +#91857 = ORIENTED_EDGE ( 'NONE', *, *, #29743, .F. ) ; +#91858 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57667 ) ) ; +#91859 = ORIENTED_EDGE ( 'NONE', *, *, #46489, .T. ) ; +#91860 = SURFACE_STYLE_FILL_AREA ( #29580 ) ; +#91861 = EDGE_CURVE ( 'NONE', #49941, #100905, #54840, .T. ) ; +#91862 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#91863 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91864 = VECTOR ( 'NONE', #95622, 1000.000000000000000 ) ; +#91865 = ORIENTED_EDGE ( 'NONE', *, *, #86343, .T. ) ; +#91866 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70738 ), #80533 ) ; +#91867 = SURFACE_STYLE_USAGE ( .BOTH. , #10796 ) ; +#91868 = VECTOR ( 'NONE', #20284, 1000.000000000000000 ) ; +#91869 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#91870 = ORIENTED_EDGE ( 'NONE', *, *, #32761, .F. ) ; +#91871 = DIRECTION ( 'NONE', ( -1.649990468822289917E-78, 1.000000000000000000, -3.396003576002217664E-125 ) ) ; +#91872 = ORIENTED_EDGE ( 'NONE', *, *, #76030, .F. ) ; +#91873 = EDGE_LOOP ( 'NONE', ( #18762, #84226, #11364, #26793 ) ) ; +#91874 = EDGE_CURVE ( 'NONE', #79783, #22518, #64317, .T. ) ; +#91875 = FILL_AREA_STYLE ('',( #85721 ) ) ; +#91876 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91877 = FILL_AREA_STYLE ('',( #99454 ) ) ; +#91878 = ADVANCED_FACE ( 'NONE', ( #6826 ), #69690, .T. ) ; +#91879 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#91880 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1350000000000000089 ) ) ; +#91881 = LINE ( 'NONE', #53106, #41533 ) ; +#91882 = FILL_AREA_STYLE ('',( #21942 ) ) ; +#91883 = VERTEX_POINT ( 'NONE', #31409 ) ; +#91884 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#91885 = CARTESIAN_POINT ( 'NONE', ( -0.9721805927153830407, -1.463531211619029992, 0.8100000000000000533 ) ) ; +#91886 = ORIENTED_EDGE ( 'NONE', *, *, #92249, .F. ) ; +#91887 = ADVANCED_FACE ( 'NONE', ( #7840 ), #61578, .F. ) ; +#91888 = AXIS2_PLACEMENT_3D ( 'NONE', #8411, #41681, #17651 ) ; +#91889 = SURFACE_SIDE_STYLE ('',( #14749 ) ) ; +#91890 = PLANE ( 'NONE', #4349 ) ; +#91891 = LINE ( 'NONE', #21949, #75739 ) ; +#91892 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #27766, #28729, #98109, #68525 ), + ( #97641, #91026, #90013, #22080 ), + ( #75700, #21088, #82381, #12336 ), + ( #29730, #5712, #29246, #60912 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#91894 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.98066299999999984, 0.8991599999999999593 ) ) ; +#91893 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91895 = CYLINDRICAL_SURFACE ( 'NONE', #51686, 0.04999999999999991257 ) ; +#91896 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#91897 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#91898 = LINE ( 'NONE', #21961, #2027 ) ; +#91899 = CIRCLE ( 'NONE', #77247, 1.319494420477459906 ) ; +#91900 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8648700000000000276 ) ) ; +#91901 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91902 = FILL_AREA_STYLE_COLOUR ( '', #11327 ) ; +#91903 = VECTOR ( 'NONE', #30765, 1000.000000000000000 ) ; +#91904 = ADVANCED_FACE ( 'NONE', ( #92652 ), #61074, .T. ) ; +#91905 = DIRECTION ( 'NONE', ( -0.7071067811865435759, 0.7071067811865514585, 0.000000000000000000 ) ) ; +#91907 = PLANE ( 'NONE', #100604 ) ; +#91906 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3872 ), #64168 ) ; +#91908 = PLANE ( 'NONE', #81160 ) ; +#91909 = STYLED_ITEM ( 'NONE', ( #10579 ), #19794 ) ; +#91911 = EDGE_LOOP ( 'NONE', ( #58202, #74414, #11641, #8976, #85448, #68940 ) ) ; +#91910 = AXIS2_PLACEMENT_3D ( 'NONE', #84508, #69146, #100708 ) ; +#91912 = CARTESIAN_POINT ( 'NONE', ( -1.010125602507139897, -1.400043273498619900, 0.8100000000000000533 ) ) ; +#91913 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16146, 'distance_accuracy_value', 'NONE'); +#91914 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62196, 'distance_accuracy_value', 'NONE'); +#91915 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#91916 = SURFACE_STYLE_FILL_AREA ( #43957 ) ; +#91917 = FILL_AREA_STYLE ('',( #60812 ) ) ; +#91918 = ADVANCED_FACE ( 'NONE', ( #88069 ), #48778, .T. ) ; +#91919 = AXIS2_PLACEMENT_3D ( 'NONE', #73354, #73841, #57542 ) ; +#91920 = FACE_OUTER_BOUND ( 'NONE', #98779, .T. ) ; +#91921 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91922 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#91923 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.100000000000000089, -0.02000000000000000042 ) ) ; +#91924 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#91925 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#91926 = AXIS2_PLACEMENT_3D ( 'NONE', #65522, #2759, #19574 ) ; +#91927 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91928 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#91929 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#91930 = ORIENTED_EDGE ( 'NONE', *, *, #100525, .F. ) ; +#91931 = PLANE ( 'NONE', #37750 ) ; +#91932 = ORIENTED_EDGE ( 'NONE', *, *, #22530, .F. ) ; +#91933 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80420, 'distance_accuracy_value', 'NONE'); +#91934 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9225, 'distance_accuracy_value', 'NONE'); +#91935 = VECTOR ( 'NONE', #29078, 1000.000000000000000 ) ; +#91936 = PLANE ( 'NONE', #85756 ) ; +#91937 = SURFACE_STYLE_FILL_AREA ( #68445 ) ; +#91938 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999989897, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#91939 = VECTOR ( 'NONE', #93090, 1000.000000000000000 ) ; +#91940 = CARTESIAN_POINT ( 'NONE', ( 6.671888000000000041, 9.934032000000000195, 0.8991599999999999593 ) ) ; +#91941 = PRESENTATION_STYLE_ASSIGNMENT (( #69956 ) ) ; +#91942 = VERTEX_POINT ( 'NONE', #63086 ) ; +#91943 = CARTESIAN_POINT ( 'NONE', ( -0.9938630133853429971, 2.355709075926970097, 0.8299999999999999600 ) ) ; +#91944 = SURFACE_SIDE_STYLE ('',( #91456 ) ) ; +#91945 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#91946 = EDGE_LOOP ( 'NONE', ( #93479, #19278, #61201, #78669 ) ) ; +#91947 = EDGE_CURVE ( 'NONE', #48855, #54059, #79751, .T. ) ; +#91948 = PRESENTATION_STYLE_ASSIGNMENT (( #83313 ) ) ; +#91949 = LINE ( 'NONE', #67453, #79417 ) ; +#91950 = VERTEX_POINT ( 'NONE', #32434 ) ; +#91951 = AXIS2_PLACEMENT_3D ( 'NONE', #89620, #27344, #66625 ) ; +#91952 = SURFACE_STYLE_FILL_AREA ( #83812 ) ; +#91953 = EDGE_CURVE ( 'NONE', #75369, #11817, #2308, .T. ) ; +#91954 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91955 = SURFACE_SIDE_STYLE ('',( #90459 ) ) ; +#91956 = ADVANCED_FACE ( 'NONE', ( #24293 ), #33452, .T. ) ; +#91958 = ORIENTED_EDGE ( 'NONE', *, *, #717, .T. ) ; +#91957 = EDGE_LOOP ( 'NONE', ( #85209, #90144, #87506, #23784 ) ) ; +#91959 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#91960 = ORIENTED_EDGE ( 'NONE', *, *, #19467, .T. ) ; +#91961 = PRESENTATION_STYLE_ASSIGNMENT (( #21030 ) ) ; +#91962 = VECTOR ( 'NONE', #64410, 1000.000000000000000 ) ; +#91963 = FACE_OUTER_BOUND ( 'NONE', #70920, .T. ) ; +#91964 = EDGE_LOOP ( 'NONE', ( #76051, #64519, #92585, #13413 ) ) ; +#91965 = VERTEX_POINT ( 'NONE', #81929 ) ; +#91966 = SURFACE_SIDE_STYLE ('',( #52200 ) ) ; +#91967 = SURFACE_SIDE_STYLE ('',( #32223 ) ) ; +#91968 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#91969 = CARTESIAN_POINT ( 'NONE', ( 0.1478084415584410005, -1.500000000000000000, 0.8100000000000000533 ) ) ; +#91970 = FILL_AREA_STYLE_COLOUR ( '', #80768 ) ; +#91971 = ORIENTED_EDGE ( 'NONE', *, *, #78300, .T. ) ; +#91972 = ORIENTED_EDGE ( 'NONE', *, *, #48178, .F. ) ; +#91973 = EDGE_LOOP ( 'NONE', ( #43498, #75062, #71980, #36779 ) ) ; +#91974 = PLANE ( 'NONE', #91614 ) ; +#91975 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95165 ) ) ; +#91976 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #2465, #93053 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #78921 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#91977 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26385 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96956, #19368, #25056 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#91979 = ORIENTED_EDGE ( 'NONE', *, *, #62009, .F. ) ; +#91978 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#91980 = AXIS2_PLACEMENT_3D ( 'NONE', #44899, #45899, #68403 ) ; +#91982 = CYLINDRICAL_SURFACE ( 'NONE', #80897, 0.05000000000000012768 ) ; +#91981 = STYLED_ITEM ( 'NONE', ( #64199 ), #20059 ) ; +#91983 = SURFACE_STYLE_USAGE ( .BOTH. , #20533 ) ; +#91984 = FILL_AREA_STYLE ('',( #14840 ) ) ; +#91985 = VERTEX_POINT ( 'NONE', #74755 ) ; +#91987 = SURFACE_STYLE_USAGE ( .BOTH. , #13303 ) ; +#91986 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#91988 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999789573 ) ) ; +#91989 = ORIENTED_EDGE ( 'NONE', *, *, #6865, .F. ) ; +#91990 = CARTESIAN_POINT ( 'NONE', ( 0.01806955754146100102, -0.9394184040112210088, 0.8299999999999988498 ) ) ; +#91991 = VECTOR ( 'NONE', #69024, 1000.000000000000114 ) ; +#91992 = FACE_OUTER_BOUND ( 'NONE', #40614, .T. ) ; +#91993 = AXIS2_PLACEMENT_3D ( 'NONE', #58543, #28256, #82875 ) ; +#91994 = EDGE_CURVE ( 'NONE', #80096, #30758, #66576, .T. ) ; +#91996 = ORIENTED_EDGE ( 'NONE', *, *, #55686, .T. ) ; +#91995 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#91997 = VECTOR ( 'NONE', #17482, 1000.000000000000000 ) ; +#91998 = LINE ( 'NONE', #47047, #66996 ) ; +#91999 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8991599999999999593 ) ) ; +#92001 = SURFACE_STYLE_USAGE ( .BOTH. , #82855 ) ; +#92000 = FILL_AREA_STYLE_COLOUR ( '', #64334 ) ; +#92002 = VECTOR ( 'NONE', #86909, 1000.000000000000114 ) ; +#92003 = FILL_AREA_STYLE ('',( #46534 ) ) ; +#92004 = ORIENTED_EDGE ( 'NONE', *, *, #60999, .F. ) ; +#92005 = EDGE_CURVE ( 'NONE', #44836, #54259, #20605, .T. ) ; +#92006 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30099 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59767, #52077, #83208 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92007 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92008 = CARTESIAN_POINT ( 'NONE', ( 1.162162005104931950, 1.364349903361174121, 0.8299999999999999600 ) ) ; +#92009 = SURFACE_SIDE_STYLE ('',( #13851 ) ) ; +#92010 = EDGE_CURVE ( 'NONE', #59650, #97964, #19615, .T. ) ; +#92012 = SURFACE_STYLE_FILL_AREA ( #46014 ) ; +#92011 = CARTESIAN_POINT ( 'NONE', ( 0.4415831003499929852, -0.9994927481818659531, 0.8100000000000000533 ) ) ; +#92013 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999992450, 3.149999999999990585, 0.000000000000000000 ) ) ; +#92014 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 11.03497999999999912, 0.8991599999999999593 ) ) ; +#92015 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50162 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57473, #65105, #87585 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92016 = SURFACE_SIDE_STYLE ('',( #46551 ) ) ; +#92017 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#92018 = ORIENTED_EDGE ( 'NONE', *, *, #13001, .T. ) ; +#92019 = ADVANCED_FACE ( 'NONE', ( #57965 ), #50794, .F. ) ; +#92020 = EDGE_CURVE ( 'NONE', #44546, #69034, #49973, .T. ) ; +#92021 = ORIENTED_EDGE ( 'NONE', *, *, #34269, .T. ) ; +#92023 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#92022 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#92024 = EDGE_CURVE ( 'NONE', #48689, #6871, #75257, .T. ) ; +#92026 = ADVANCED_FACE ( 'NONE', ( #49785 ), #90057, .T. ) ; +#92025 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92027 = VECTOR ( 'NONE', #79655, 1000.000000000000000 ) ; +#92028 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61096 ), #48040 ) ; +#92029 = ORIENTED_EDGE ( 'NONE', *, *, #24531, .T. ) ; +#92030 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92031 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92032 = AXIS2_PLACEMENT_3D ( 'NONE', #19526, #41521, #57885 ) ; +#92033 = ADVANCED_FACE ( 'NONE', ( #53279 ), #7712, .T. ) ; +#92034 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92035 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, 1.048695503451051965E-76 ) ) ; +#92036 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92037 = LINE ( 'NONE', #23621, #40393 ) ; +#92038 = STYLED_ITEM ( 'NONE', ( #49399 ), #48364 ) ; +#92039 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92040 = FILL_AREA_STYLE_COLOUR ( '', #74086 ) ; +#92041 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #90565, #84402 ), + ( #13900, #45066 ), + ( #37951, #68055 ), + ( #5753, #59962 ), + ( #82423, #14409 ), + ( #44098, #83417 ), + ( #60947, #83907 ), + ( #99138, #29767 ), + ( #76742, #29285 ), + ( #60461, #69039 ), + ( #21117, #52287 ), + ( #100112, #51776 ), + ( #30253, #61454 ), + ( #20602, #82915 ), + ( #13377, #91556 ), + ( #12372, #12877 ), + ( #75254, #5248 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07368751262769819566, 0.1417920735975989888, 0.2054115302518020048, 0.2658518701935390083, 0.3244427805873359993, 0.3816258437036210149, 0.4386397466422020108, 0.4960160260037990154, 0.5547989483227619978, 0.6144450223394869459, 0.6760330661510810524, 0.7394243817737220503, 0.8697955919226260102, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#92042 = ADVANCED_FACE ( 'NONE', ( #84900 ), #92057, .F. ) ; +#92043 = FILL_AREA_STYLE ('',( #94016 ) ) ; +#92044 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19752, 'distance_accuracy_value', 'NONE'); +#92045 = AXIS2_PLACEMENT_3D ( 'NONE', #93801, #55592, #95331 ) ; +#92046 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#92047 = ORIENTED_EDGE ( 'NONE', *, *, #89402, .F. ) ; +#92048 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92049 = ORIENTED_EDGE ( 'NONE', *, *, #6210, .F. ) ; +#92050 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#92051 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19045, 'distance_accuracy_value', 'NONE'); +#92052 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32897, 'distance_accuracy_value', 'NONE'); +#92053 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92054 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#92055 = PRESENTATION_STYLE_ASSIGNMENT (( #30767 ) ) ; +#92056 = VECTOR ( 'NONE', #80636, 1000.000000000000000 ) ; +#92057 = PLANE ( 'NONE', #24432 ) ; +#92058 = SURFACE_STYLE_USAGE ( .BOTH. , #75259 ) ; +#92059 = FACE_OUTER_BOUND ( 'NONE', #34374, .T. ) ; +#92060 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999112, -0.3000000000000020983, 0.8299999999999999600 ) ) ; +#92061 = ORIENTED_EDGE ( 'NONE', *, *, #87099, .F. ) ; +#92062 = DIRECTION ( 'NONE', ( 0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#92063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4229, 'distance_accuracy_value', 'NONE'); +#92066 = VECTOR ( 'NONE', #90618, 1000.000000000000000 ) ; +#92065 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000013115, 0.2399999999999999911 ) ) ; +#92067 = STYLED_ITEM ( 'NONE', ( #876 ), #98537 ) ; +#92068 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92069 = EDGE_LOOP ( 'NONE', ( #40904, #56055, #75615, #18268 ) ) ; +#92070 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92071 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92072 = AXIS2_PLACEMENT_3D ( 'NONE', #72022, #32718, #96970 ) ; +#92073 = CARTESIAN_POINT ( 'NONE', ( -1.275112219867899910, -1.401744930657430110, 0.8100000000000000533 ) ) ; +#92074 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92075 = ADVANCED_FACE ( 'NONE', ( #13380 ), #13903, .T. ) ; +#92076 = ORIENTED_EDGE ( 'NONE', *, *, #82598, .T. ) ; +#92077 = AXIS2_PLACEMENT_3D ( 'NONE', #33098, #86197, #46879 ) ; +#92078 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23003, 'distance_accuracy_value', 'NONE'); +#92079 = VECTOR ( 'NONE', #72551, 1000.000000000000000 ) ; +#92080 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92081 = EDGE_CURVE ( 'NONE', #72032, #38761, #15945, .T. ) ; +#92082 = EDGE_LOOP ( 'NONE', ( #20159, #15833, #31767, #17411 ) ) ; +#92083 = CARTESIAN_POINT ( 'NONE', ( 8.842705999999999733, 10.11080899999999971, 0.8991599999999999593 ) ) ; +#92084 = VECTOR ( 'NONE', #85437, 1000.000000000000000 ) ; +#92085 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92086 = ORIENTED_EDGE ( 'NONE', *, *, #29112, .F. ) ; +#92087 = AXIS2_PLACEMENT_3D ( 'NONE', #91004, #21066, #44512 ) ; +#92088 = VECTOR ( 'NONE', #76977, 1000.000000000000000 ) ; +#92090 = ADVANCED_FACE ( 'NONE', ( #33323 ), #31280, .T. ) ; +#92089 = AXIS2_PLACEMENT_3D ( 'NONE', #54376, #16033, #225 ) ; +#92091 = EDGE_LOOP ( 'NONE', ( #69185, #3946, #57297, #75634 ) ) ; +#92093 = EDGE_LOOP ( 'NONE', ( #15556, #30682, #55099, #83597 ) ) ; +#92092 = CYLINDRICAL_SURFACE ( 'NONE', #39544, 0.09406596738343675490 ) ; +#92094 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 13.40000000000000036, 0.03429000000000000103 ) ) ; +#92095 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43212 ) ) ; +#92097 = CARTESIAN_POINT ( 'NONE', ( -1.394805194805190052, -1.300689935064940128, 0.8299999999999999600 ) ) ; +#92096 = PRESENTATION_STYLE_ASSIGNMENT (( #44619 ) ) ; +#92099 = SURFACE_SIDE_STYLE ('',( #84450 ) ) ; +#92098 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92100 = PLANE ( 'NONE', #94417 ) ; +#92101 = ORIENTED_EDGE ( 'NONE', *, *, #71559, .T. ) ; +#92102 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92103 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.6999999999999990674, 5.234185452379087911E-79 ) ) ; +#92104 = VERTEX_POINT ( 'NONE', #8226 ) ; +#92105 = EDGE_CURVE ( 'NONE', #53179, #56071, #137, .T. ) ; +#92106 = CARTESIAN_POINT ( 'NONE', ( 1.440857328897279910, -1.359907766992060285, 0.8100000000000000533 ) ) ; +#92107 = FACE_OUTER_BOUND ( 'NONE', #2224, .T. ) ; +#92108 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7276 ) ) ; +#92109 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30151 ), #80860 ) ; +#92110 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92111 = ORIENTED_EDGE ( 'NONE', *, *, #22077, .F. ) ; +#92114 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#92113 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#92112 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92115 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22083 ), #93755 ) ; +#92116 = ORIENTED_EDGE ( 'NONE', *, *, #28812, .T. ) ; +#92117 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43227 ) ) ; +#92119 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.1000000000000020040, 0.1829999999999709914 ) ) ; +#92118 = LINE ( 'NONE', #62019, #91939 ) ; +#92120 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#92121 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #271 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #94591, #38604, #61613 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92122 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#92123 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #95867, #94853, #72399, #87736 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#92124 = EDGE_LOOP ( 'NONE', ( #2220, #14821, #93898, #86464 ) ) ; +#92125 = LINE ( 'NONE', #24237, #9016 ) ; +#92126 = ORIENTED_EDGE ( 'NONE', *, *, #93900, .T. ) ; +#92127 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74224 ), #20417 ) ; +#92129 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#92128 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#92130 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92131 = FILL_AREA_STYLE_COLOUR ( '', #47638 ) ; +#92132 = LINE ( 'NONE', #38033, #38161 ) ; +#92133 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92134 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#92135 = ORIENTED_EDGE ( 'NONE', *, *, #76435, .T. ) ; +#92136 = SURFACE_STYLE_FILL_AREA ( #61036 ) ; +#92137 = PRESENTATION_STYLE_ASSIGNMENT (( #70166 ) ) ; +#92139 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92138 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#92140 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#92141 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53037 ), #23665 ) ; +#92143 = EDGE_CURVE ( 'NONE', #64228, #84179, #86347, .T. ) ; +#92142 = FACE_OUTER_BOUND ( 'NONE', #90725, .T. ) ; +#92144 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23285 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7240, #20627, #44117 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92145 = CARTESIAN_POINT ( 'NONE', ( -1.285308266724690007, -1.390907012919420094, 0.8299999999999998490 ) ) ; +#92146 = FILL_AREA_STYLE ('',( #36559 ) ) ; +#92147 = VERTEX_POINT ( 'NONE', #94562 ) ; +#92148 = PRESENTATION_STYLE_ASSIGNMENT (( #99713 ) ) ; +#92149 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#92150 = CARTESIAN_POINT ( 'NONE', ( -1.970710678118654302, 1.529289321881343922, -0.02000000000000000042 ) ) ; +#92151 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#92152 = CARTESIAN_POINT ( 'NONE', ( 0.009882622001633050227, -1.368793146596559929, 0.8299999999999999600 ) ) ; +#92153 = EDGE_CURVE ( 'NONE', #90348, #62388, #39445, .T. ) ; +#92154 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92155 = VECTOR ( 'NONE', #12796, 1000.000000000000114 ) ; +#92156 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#92157 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8277, 'distance_accuracy_value', 'NONE'); +#92158 = FILL_AREA_STYLE_COLOUR ( '', #44819 ) ; +#92159 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#92160 = VECTOR ( 'NONE', #32128, 1000.000000000000000 ) ; +#92161 = FACE_OUTER_BOUND ( 'NONE', #87512, .T. ) ; +#92162 = SURFACE_SIDE_STYLE ('',( #4391 ) ) ; +#92163 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92164 = PRESENTATION_STYLE_ASSIGNMENT (( #29876 ) ) ; +#92165 = EDGE_CURVE ( 'NONE', #41349, #66504, #6403, .T. ) ; +#92166 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92167 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92168 = LINE ( 'NONE', #6822, #75741 ) ; +#92169 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87928, 'distance_accuracy_value', 'NONE'); +#92170 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.6500000000000001332, 0.000000000000000000 ) ) ; +#92171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80949, 'distance_accuracy_value', 'NONE'); +#92172 = SURFACE_STYLE_USAGE ( .BOTH. , #60574 ) ; +#92173 = STYLED_ITEM ( 'NONE', ( #94246 ), #83446 ) ; +#92174 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92175 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69198 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38169, #6923, #23872 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92176 = LINE ( 'NONE', #61075, #11141 ) ; +#92177 = SURFACE_SIDE_STYLE ('',( #69692 ) ) ; +#92178 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92179 = SURFACE_STYLE_USAGE ( .BOTH. , #75865 ) ; +#92180 = ORIENTED_EDGE ( 'NONE', *, *, #73956, .F. ) ; +#92181 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92182 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92183 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70460, 'distance_accuracy_value', 'NONE'); +#92185 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92184 = STYLED_ITEM ( 'NONE', ( #24658 ), #89143 ) ; +#92186 = LINE ( 'NONE', #61083, #43809 ) ; +#92187 = ORIENTED_EDGE ( 'NONE', *, *, #22569, .T. ) ; +#92188 = CARTESIAN_POINT ( 'NONE', ( -0.01185217942543770157, -1.028719707420159946, 0.8300000000000002931 ) ) ; +#92189 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, 0.000000000000000000 ) ) ; +#92190 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86042 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35266, #36251, #19909 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92191 = FILL_AREA_STYLE_COLOUR ( '', #68523 ) ; +#92192 = ORIENTED_EDGE ( 'NONE', *, *, #46255, .F. ) ; +#92193 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89999, 'distance_accuracy_value', 'NONE'); +#92194 = STYLED_ITEM ( 'NONE', ( #30624 ), #20714 ) ; +#92195 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.155799999999999272, 0.8991599999999999593 ) ) ; +#92196 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74224 ) ) ; +#92197 = EDGE_CURVE ( 'NONE', #41411, #87071, #70591, .T. ) ; +#92198 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92199 = ORIENTED_EDGE ( 'NONE', *, *, #100061, .T. ) ; +#92200 = ORIENTED_EDGE ( 'NONE', *, *, #16971, .T. ) ; +#92201 = VECTOR ( 'NONE', #91374, 1000.000000000000000 ) ; +#92202 = CIRCLE ( 'NONE', #74305, 0.02999999999999997113 ) ; +#92203 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92204 = VERTEX_POINT ( 'NONE', #63956 ) ; +#92205 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92206 = CARTESIAN_POINT ( 'NONE', ( -0.09183755801571232003, -1.507352529807550079, 0.8299999999999999600 ) ) ; +#92207 = FACE_BOUND ( 'NONE', #78176, .T. ) ; +#92208 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92209 = SURFACE_STYLE_USAGE ( .BOTH. , #61107 ) ; +#92210 = AXIS2_PLACEMENT_3D ( 'NONE', #60288, #89387, #13208 ) ; +#92211 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#92212 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #33899, #58257 ) ; +#92213 = SURFACE_STYLE_FILL_AREA ( #78418 ) ; +#92214 = ORIENTED_EDGE ( 'NONE', *, *, #60484, .T. ) ; +#92215 = AXIS2_PLACEMENT_3D ( 'NONE', #6651, #92956, #47034 ) ; +#92216 = VERTEX_POINT ( 'NONE', #41485 ) ; +#92217 = FACE_OUTER_BOUND ( 'NONE', #92961, .T. ) ; +#92218 = AXIS2_PLACEMENT_3D ( 'NONE', #8740, #66475, #56845 ) ; +#92220 = CARTESIAN_POINT ( 'NONE', ( 1.337707442669689994, -0.9199924700473179895, 0.8299999999999999600 ) ) ; +#92219 = FACE_OUTER_BOUND ( 'NONE', #77154, .T. ) ; +#92221 = EDGE_CURVE ( 'NONE', #53059, #70676, #100855, .T. ) ; +#92222 = DIRECTION ( 'NONE', ( -1.626303258728260102E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92223 = VERTEX_POINT ( 'NONE', #87428 ) ; +#92224 = VECTOR ( 'NONE', #9924, 1000.000000000000000 ) ; +#92225 = ADVANCED_FACE ( 'NONE', ( #93536 ), #637, .T. ) ; +#92226 = ORIENTED_EDGE ( 'NONE', *, *, #50739, .F. ) ; +#92227 = ORIENTED_EDGE ( 'NONE', *, *, #89564, .F. ) ; +#92228 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92230 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92229 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92231 = FACE_OUTER_BOUND ( 'NONE', #22671, .T. ) ; +#92232 = DIRECTION ( 'NONE', ( -1.000000000000000000, -9.346570452461245291E-17, 0.000000000000000000 ) ) ; +#92234 = ORIENTED_EDGE ( 'NONE', *, *, #7465, .F. ) ; +#92233 = PRESENTATION_STYLE_ASSIGNMENT (( #76937 ) ) ; +#92235 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92236 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.63512000000000057, 0.8648700000000000276 ) ) ; +#92237 = SURFACE_SIDE_STYLE ('',( #28476 ) ) ; +#92238 = STYLED_ITEM ( 'NONE', ( #91138 ), #83638 ) ; +#92239 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #12299 ) ) ; +#92240 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92241 = STYLED_ITEM ( 'NONE', ( #9704 ), #54405 ) ; +#92242 = ORIENTED_EDGE ( 'NONE', *, *, #69636, .F. ) ; +#92244 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92243 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92245 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -2.914335439641030002E-16 ) ) ; +#92246 = EDGE_LOOP ( 'NONE', ( #10754, #69980, #14122, #2089 ) ) ; +#92247 = VERTEX_POINT ( 'NONE', #51163 ) ; +#92248 = FILL_AREA_STYLE ('',( #11675 ) ) ; +#92249 = EDGE_CURVE ( 'NONE', #76160, #40173, #42488, .T. ) ; +#92250 = CARTESIAN_POINT ( 'NONE', ( 1.157750320739350247, -1.512608977738969962, 0.8100000000000000533 ) ) ; +#92251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92252 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6800 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5966, #37688, #91290 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92253 = PRESENTATION_STYLE_ASSIGNMENT (( #20819 ) ) ; +#92254 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8100000000000086020 ) ) ; +#92255 = VECTOR ( 'NONE', #71415, 1000.000000000000000 ) ; +#92256 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97133 ) ) ; +#92257 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#92258 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #65015 ) ; +#92259 = SURFACE_STYLE_FILL_AREA ( #44283 ) ; +#92260 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92261 = ORIENTED_EDGE ( 'NONE', *, *, #52356, .F. ) ; +#92262 = ORIENTED_EDGE ( 'NONE', *, *, #32623, .F. ) ; +#92263 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79245 ) ) ; +#92264 = PRESENTATION_STYLE_ASSIGNMENT (( #29970 ) ) ; +#92265 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 15.15000000000000036, 0.000000000000000000 ) ) ; +#92266 = FILL_AREA_STYLE_COLOUR ( '', #15761 ) ; +#92267 = ADVANCED_FACE ( 'NONE', ( #26679 ), #12252, .T. ) ; +#92268 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92269 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #85461, #53329, #15487, #29820, #69621, #14468, #100650, #44628 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000006661, 0.5000000000000013323, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#92270 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -1.099999999999999867, 8.599018957360380094E-79 ) ) ; +#92271 = VECTOR ( 'NONE', #83805, 1000.000000000000114 ) ; +#92272 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#92273 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -0.7000000000000009548, 3.495651678169978796E-76 ) ) ; +#92274 = SURFACE_STYLE_USAGE ( .BOTH. , #69789 ) ; +#92275 = EDGE_LOOP ( 'NONE', ( #74649, #83601, #29578, #50219 ) ) ; +#92276 = STYLED_ITEM ( 'NONE', ( #25478 ), #39210 ) ; +#92277 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.5000000000000000000, -0.02000000000000000042 ) ) ; +#92278 = FILL_AREA_STYLE ('',( #54521 ) ) ; +#92279 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100330 ) ) ; +#92280 = DIRECTION ( 'NONE', ( -0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#92281 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000029060, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#92282 = FILL_AREA_STYLE_COLOUR ( '', #45070 ) ; +#92283 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#92284 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92285 = PRESENTATION_STYLE_ASSIGNMENT (( #68297 ) ) ; +#92286 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89107 ) ) ; +#92287 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#92288 = EDGE_CURVE ( 'NONE', #18135, #88593, #74633, .T. ) ; +#92289 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92290 = PLANE ( 'NONE', #48441 ) ; +#92291 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#92292 = LINE ( 'NONE', #38684, #6134 ) ; +#92293 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92294 = AXIS2_PLACEMENT_3D ( 'NONE', #61612, #93183, #295 ) ; +#92295 = PLANE ( 'NONE', #24180 ) ; +#92296 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #5651, 'distance_accuracy_value', 'NONE'); +#92297 = CARTESIAN_POINT ( 'NONE', ( 0.09350649350649301028, -1.329788961038959938, 0.8099999999999013545 ) ) ; +#92298 = SURFACE_STYLE_USAGE ( .BOTH. , #45311 ) ; +#92299 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#92300 = ORIENTED_EDGE ( 'NONE', *, *, #46477, .T. ) ; +#92301 = LINE ( 'NONE', #22359, #61171 ) ; +#92302 = CARTESIAN_POINT ( 'NONE', ( 1.678890544094119974, -1.445107798742939931, 0.8299999999999977396 ) ) ; +#92303 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92304 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63642, 'distance_accuracy_value', 'NONE'); +#92305 = STYLED_ITEM ( 'NONE', ( #85105 ), #73237 ) ; +#92306 = LINE ( 'NONE', #53531, #18812 ) ; +#92307 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#92308 = CARTESIAN_POINT ( 'NONE', ( 9.507386999999999588, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#92309 = ORIENTED_EDGE ( 'NONE', *, *, #57481, .F. ) ; +#92310 = FACE_OUTER_BOUND ( 'NONE', #87622, .T. ) ; +#92311 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92312 = FILL_AREA_STYLE_COLOUR ( '', #56042 ) ; +#92313 = LINE ( 'NONE', #45821, #7900 ) ; +#92314 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41161, 'distance_accuracy_value', 'NONE'); +#92315 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92316 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35315 ), #4296 ) ; +#92317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20486, 'distance_accuracy_value', 'NONE'); +#92318 = EDGE_CURVE ( 'NONE', #81709, #36125, #94930, .T. ) ; +#92319 = PRESENTATION_STYLE_ASSIGNMENT (( #12656 ) ) ; +#92320 = STYLED_ITEM ( 'NONE', ( #54240 ), #61524 ) ; +#92321 = PRESENTATION_STYLE_ASSIGNMENT (( #91811 ) ) ; +#92322 = ORIENTED_EDGE ( 'NONE', *, *, #19785, .F. ) ; +#92323 = ORIENTED_EDGE ( 'NONE', *, *, #12308, .T. ) ; +#92324 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92325 = ORIENTED_EDGE ( 'NONE', *, *, #78642, .T. ) ; +#92326 = LINE ( 'NONE', #61226, #21826 ) ; +#92327 = AXIS2_PLACEMENT_3D ( 'NONE', #71285, #17146, #72810 ) ; +#92328 = VECTOR ( 'NONE', #53053, 1000.000000000000000 ) ; +#92329 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8648700000000000276 ) ) ; +#92330 = SURFACE_STYLE_USAGE ( .BOTH. , #61228 ) ; +#92331 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92332 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#92333 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #68422 ) ; +#92334 = LINE ( 'NONE', #70354, #32916 ) ; +#92335 = STYLED_ITEM ( 'NONE', ( #63641 ), #77894 ) ; +#92336 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.383333333333333526, 0.000000000000000000 ) ) ; +#92338 = ORIENTED_EDGE ( 'NONE', *, *, #47134, .F. ) ; +#92337 = EDGE_LOOP ( 'NONE', ( #71028, #96870, #58214, #63837 ) ) ; +#92339 = EDGE_LOOP ( 'NONE', ( #71767, #20921, #88306, #42790 ) ) ; +#92340 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92342 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#92341 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220075051, 1.500000000000000000, -0.02000000000000000042 ) ) ; +#92343 = EDGE_LOOP ( 'NONE', ( #1139, #24207, #98825, #52057 ) ) ; +#92344 = ORIENTED_EDGE ( 'NONE', *, *, #5272, .T. ) ; +#92345 = AXIS2_PLACEMENT_3D ( 'NONE', #22455, #45901, #100435 ) ; +#92346 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92347 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.004999999999999942858, -0.1400000000000000133 ) ) ; +#92348 = DIRECTION ( 'NONE', ( 0.7071090539100477468, 0.7071045084557425753, 0.000000000000000000 ) ) ; +#92349 = CARTESIAN_POINT ( 'NONE', ( -0.4878449414651300775, -0.9061750041553330304, 0.8299999999999999600 ) ) ; +#92350 = EDGE_LOOP ( 'NONE', ( #100300, #21740, #44223 ) ) ; +#92351 = CARTESIAN_POINT ( 'NONE', ( 0.9833333333333340587, -3.099999999999980549, 0.000000000000000000 ) ) ; +#92352 = EDGE_CURVE ( 'NONE', #26467, #39738, #81316, .T. ) ; +#92353 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54939 ), #48391 ) ; +#92354 = ORIENTED_EDGE ( 'NONE', *, *, #22643, .T. ) ; +#92355 = ADVANCED_FACE ( 'NONE', ( #41993 ), #73126, .F. ) ; +#92356 = ORIENTED_EDGE ( 'NONE', *, *, #91205, .F. ) ; +#92357 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92358 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92361 = VERTEX_POINT ( 'NONE', #29174 ) ; +#92360 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98571, 'distance_accuracy_value', 'NONE'); +#92359 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92362 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#92363 = VECTOR ( 'NONE', #66119, 1000.000000000000000 ) ; +#92364 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92365 = VERTEX_POINT ( 'NONE', #91938 ) ; +#92366 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#92367 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92368 = EDGE_LOOP ( 'NONE', ( #99898, #3093, #45586, #19981 ) ) ; +#92369 = ORIENTED_EDGE ( 'NONE', *, *, #81769, .F. ) ; +#92370 = ADVANCED_FACE ( 'NONE', ( #21994 ), #44948, .F. ) ; +#92371 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#92372 = FILL_AREA_STYLE_COLOUR ( '', #48179 ) ; +#92373 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92374 = CARTESIAN_POINT ( 'NONE', ( 1.041560975556909963, -1.173235213159260049, 0.8299999999999997380 ) ) ; +#92375 = SURFACE_STYLE_USAGE ( .BOTH. , #69376 ) ; +#92376 = VERTEX_POINT ( 'NONE', #44453 ) ; +#92377 = CARTESIAN_POINT ( 'NONE', ( 0.4674268961122319821, -1.076021161212330046, 0.8299999999999999600 ) ) ; +#92378 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92379 = VERTEX_POINT ( 'NONE', #83799 ) ; +#92380 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92381 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65878, 'distance_accuracy_value', 'NONE'); +#92383 = EDGE_CURVE ( 'NONE', #71293, #99033, #59762, .T. ) ; +#92382 = CARTESIAN_POINT ( 'NONE', ( 0.5238200612200860640, -3.099999999999980105, 0.000000000000000000 ) ) ; +#92384 = VECTOR ( 'NONE', #20985, 1000.000000000000000 ) ; +#92385 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92386 = FILL_AREA_STYLE_COLOUR ( '', #85796 ) ; +#92387 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92388 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, -0.2250000000000000333 ) ) ; +#92389 = VECTOR ( 'NONE', #32551, 1000.000000000000000 ) ; +#92390 = EDGE_CURVE ( 'NONE', #11778, #52561, #53656, .T. ) ; +#92391 = FILL_AREA_STYLE ('',( #84745 ) ) ; +#92392 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92393 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92394 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#92395 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92396 = EDGE_CURVE ( 'NONE', #6871, #61035, #60985, .T. ) ; +#92397 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92398 = ADVANCED_FACE ( 'NONE', ( #16315 ), #40361, .T. ) ; +#92400 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92399 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92401 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.676179938779915002, -0.02000000000000000042 ) ) ; +#92402 = STYLED_ITEM ( 'NONE', ( #62692 ), #40856 ) ; +#92403 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36224 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51297, #12392, #95694 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92404 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #92909, 'distance_accuracy_value', 'NONE'); +#92405 = VERTEX_POINT ( 'NONE', #94936 ) ; +#92407 = AXIS2_PLACEMENT_3D ( 'NONE', #41332, #95395, #81140 ) ; +#92406 = LINE ( 'NONE', #82768, #17185 ) ; +#92408 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, -0.02000000000000000042 ) ) ; +#92409 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92410 = VECTOR ( 'NONE', #72741, 1000.000000000000000 ) ; +#92411 = SURFACE_SIDE_STYLE ('',( #76601 ) ) ; +#92412 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92413 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92414 = FACE_OUTER_BOUND ( 'NONE', #61404, .T. ) ; +#92415 = STYLED_ITEM ( 'NONE', ( #72622 ), #5492 ) ; +#92416 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25630 ) ) ; +#92417 = LINE ( 'NONE', #83291, #46928 ) ; +#92418 = EDGE_CURVE ( 'NONE', #690, #98322, #55694, .T. ) ; +#92419 = VERTEX_POINT ( 'NONE', #46986 ) ; +#92420 = VERTEX_POINT ( 'NONE', #87303 ) ; +#92421 = FILL_AREA_STYLE_COLOUR ( '', #91065 ) ; +#92422 = SURFACE_STYLE_USAGE ( .BOTH. , #62841 ) ; +#92423 = CARTESIAN_POINT ( 'NONE', ( 5.080898000000000359, 3.266015000000000335, 0.8991599999999999593 ) ) ; +#92424 = CARTESIAN_POINT ( 'NONE', ( -0.1737436406883610396, -0.9784189978443861291, 0.8100000000000000533 ) ) ; +#92425 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74311 ), #9211 ) ; +#92426 = LINE ( 'NONE', #55696, #53372 ) ; +#92427 = FACE_OUTER_BOUND ( 'NONE', #24330, .T. ) ; +#92428 = VERTEX_POINT ( 'NONE', #56708 ) ; +#92429 = EDGE_CURVE ( 'NONE', #17853, #81114, #70983, .T. ) ; +#92430 = SURFACE_SIDE_STYLE ('',( #61350 ) ) ; +#92431 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92432 = EDGE_LOOP ( 'NONE', ( #64571, #33612, #5303 ) ) ; +#92433 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#92434 = ORIENTED_EDGE ( 'NONE', *, *, #63740, .T. ) ; +#92435 = EDGE_CURVE ( 'NONE', #66256, #7208, #17342, .T. ) ; +#92436 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92437 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92438 = CARTESIAN_POINT ( 'NONE', ( 9.355995000000000061, 10.76853099999999941, 0.8991599999999999593 ) ) ; +#92439 = STYLED_ITEM ( 'NONE', ( #82145 ), #30643 ) ; +#92440 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92441 = CARTESIAN_POINT ( 'NONE', ( 0.07998825283294179467, 0.9846819388683785146, 0.8100000000000003864 ) ) ; +#92442 = EDGE_CURVE ( 'NONE', #8103, #100590, #48533, .T. ) ; +#92444 = ORIENTED_EDGE ( 'NONE', *, *, #98275, .F. ) ; +#92443 = VERTEX_POINT ( 'NONE', #95439 ) ; +#92445 = LINE ( 'NONE', #37854, #35940 ) ; +#92446 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#92447 = ORIENTED_EDGE ( 'NONE', *, *, #85684, .F. ) ; +#92448 = SURFACE_STYLE_FILL_AREA ( #90976 ) ; +#92449 = AXIS2_PLACEMENT_3D ( 'NONE', #26783, #34948, #75604 ) ; +#92450 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35450 ) ) ; +#92452 = CARTESIAN_POINT ( 'NONE', ( -0.4442493331421650260, -1.074915662348969958, 0.8299999999999999600 ) ) ; +#92451 = CARTESIAN_POINT ( 'NONE', ( 7.739618999999999360, 5.203488000000000113, 0.8648700000000000276 ) ) ; +#92453 = ORIENTED_EDGE ( 'NONE', *, *, #40773, .F. ) ; +#92454 = ORIENTED_EDGE ( 'NONE', *, *, #81911, .F. ) ; +#92455 = PRESENTATION_STYLE_ASSIGNMENT (( #45468 ) ) ; +#92456 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92457 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92458 = VECTOR ( 'NONE', #57915, 1000.000000000000000 ) ; +#92460 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92459 = FILL_AREA_STYLE ('',( #61380 ) ) ; +#92461 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.750000000000000000, 0.000000000000000000 ) ) ; +#92462 = EDGE_LOOP ( 'NONE', ( #40404, #58562, #100370, #24345 ) ) ; +#92463 = VERTEX_POINT ( 'NONE', #55197 ) ; +#92464 = ORIENTED_EDGE ( 'NONE', *, *, #27837, .F. ) ; +#92465 = ADVANCED_FACE ( 'NONE', ( #2053 ), #77633, .T. ) ; +#92466 = SURFACE_STYLE_USAGE ( .BOTH. , #22040 ) ; +#92467 = VECTOR ( 'NONE', #59114, 1000.000000000000000 ) ; +#92468 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53355 ), #43644 ) ; +#92470 = VERTEX_POINT ( 'NONE', #72481 ) ; +#92469 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 5.549969999999999182, 0.8648700000000000276 ) ) ; +#92471 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32166 ) ) ; +#92472 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63156 ), #22375 ) ; +#92473 = CARTESIAN_POINT ( 'NONE', ( 4.847552875125042959, 4.418599124874956097, 0.8991599999999999593 ) ) ; +#92474 = ORIENTED_EDGE ( 'NONE', *, *, #2723, .T. ) ; +#92475 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #17330, #71479, #16806, #86286 ), + ( #94431, #10090, #48524, #86799 ), + ( #24552, #62834, #55679, #40855 ), + ( #95426, #2040, #47993, #79662 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 0.8047378541243649375, 0.6476030138606876374, 0.6476030138606876374, 0.8047378541243649375), + ( 1.000000000000000000, 0.8047378541243649375, 0.8047378541243649375, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#92476 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92477 = CLOSED_SHELL ( 'NONE', ( #52035, #28876, #98725, #27501, #43718, #9091 ) ) ; +#92478 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92479 = ORIENTED_EDGE ( 'NONE', *, *, #98263, .T. ) ; +#92480 = ADVANCED_FACE ( 'NONE', ( #73513 ), #11119, .T. ) ; +#92481 = FACE_BOUND ( 'NONE', #24341, .T. ) ; +#92482 = EDGE_CURVE ( 'NONE', #19502, #25989, #74006, .T. ) ; +#92483 = VECTOR ( 'NONE', #91449, 1000.000000000000114 ) ; +#92484 = PRESENTATION_STYLE_ASSIGNMENT (( #67993 ) ) ; +#92486 = VERTEX_POINT ( 'NONE', #26550 ) ; +#92485 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92488 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92487 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82687 ) ) ; +#92490 = CARTESIAN_POINT ( 'NONE', ( 1.687860199445399889, -1.507611749840819915, 0.8100000000000000533 ) ) ; +#92489 = LINE ( 'NONE', #93482, #20222 ) ; +#92491 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92492 = PRESENTATION_STYLE_ASSIGNMENT (( #14360 ) ) ; +#92493 = ORIENTED_EDGE ( 'NONE', *, *, #39408, .T. ) ; +#92494 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92495 = EDGE_CURVE ( 'NONE', #44555, #20018, #53560, .T. ) ; +#92497 = CARTESIAN_POINT ( 'NONE', ( 1.608267340221630093, -1.417598257925390293, 0.8100000000000000533 ) ) ; +#92496 = CARTESIAN_POINT ( 'NONE', ( -0.9499999999999999556, 3.099999999999989875, 0.000000000000000000 ) ) ; +#92498 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92499 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92500 = EDGE_CURVE ( 'NONE', #17269, #85574, #97926, .T. ) ; +#92501 = SURFACE_STYLE_USAGE ( .BOTH. , #14876 ) ; +#92502 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59606 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28377, #61044, #20705 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92503 = EDGE_LOOP ( 'NONE', ( #13233, #26202, #49544, #56482 ) ) ; +#92504 = FACE_OUTER_BOUND ( 'NONE', #73845, .T. ) ; +#92505 = PRESENTATION_STYLE_ASSIGNMENT (( #44053 ) ) ; +#92506 = VERTEX_POINT ( 'NONE', #88321 ) ; +#92507 = EDGE_CURVE ( 'NONE', #23447, #96986, #68472, .T. ) ; +#92508 = VECTOR ( 'NONE', #46808, 1000.000000000000000 ) ; +#92509 = SURFACE_STYLE_FILL_AREA ( #100079 ) ; +#92510 = EDGE_CURVE ( 'NONE', #19133, #20296, #65327, .T. ) ; +#92511 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92512 = AXIS2_PLACEMENT_3D ( 'NONE', #83162, #13124, #75490 ) ; +#92513 = LINE ( 'NONE', #76713, #37984 ) ; +#92514 = ORIENTED_EDGE ( 'NONE', *, *, #69059, .F. ) ; +#92515 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -0.05000000000000000278, 0.08229670385730990245 ) ) ; +#92516 = AXIS2_PLACEMENT_3D ( 'NONE', #55918, #14521, #61567 ) ; +#92517 = CARTESIAN_POINT ( 'NONE', ( -0.04997673550079750199, -1.145059460293619935, 0.8300000000000005151 ) ) ; +#92518 = FACE_OUTER_BOUND ( 'NONE', #25571, .T. ) ; +#92519 = CARTESIAN_POINT ( 'NONE', ( 1.001160189360249975, -1.432289833627879982, 0.8300000000000010703 ) ) ; +#92520 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#92521 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92522 = FILL_AREA_STYLE_COLOUR ( '', #68736 ) ; +#92523 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#92524 = PLANE ( 'NONE', #6119 ) ; +#92525 = LINE ( 'NONE', #83407, #23572 ) ; +#92526 = FILL_AREA_STYLE ('',( #14905 ) ) ; +#92527 = CIRCLE ( 'NONE', #77834, 0.1200000000000000927 ) ; +#92528 = EDGE_CURVE ( 'NONE', #35375, #86105, #30019, .T. ) ; +#92529 = AXIS2_PLACEMENT_3D ( 'NONE', #74114, #73107, #33305 ) ; +#92530 = VECTOR ( 'NONE', #49502, 1000.000000000000000 ) ; +#92531 = EDGE_LOOP ( 'NONE', ( #16721, #36129, #38752, #46772 ) ) ; +#92532 = VERTEX_POINT ( 'NONE', #13134 ) ; +#92533 = SURFACE_STYLE_FILL_AREA ( #84891 ) ; +#92534 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92536 = AXIS2_PLACEMENT_3D ( 'NONE', #27798, #66080, #26787 ) ; +#92535 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92538 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92537 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 7.989847209769839736E-17, 0.4000000000000000222 ) ) ; +#92539 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92540 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72980 ), #42014 ) ; +#92541 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#92542 = SURFACE_STYLE_FILL_AREA ( #8229 ) ; +#92543 = CLOSED_SHELL ( 'NONE', ( #78987, #7484, #30159, #24766, #3768, #19046 ) ) ; +#92544 = EDGE_LOOP ( 'NONE', ( #24671, #18365, #93071, #27767 ) ) ; +#92545 = FILL_AREA_STYLE_COLOUR ( '', #57458 ) ; +#92546 = ADVANCED_FACE ( 'NONE', ( #90317 ), #84168, .T. ) ; +#92547 = FACE_OUTER_BOUND ( 'NONE', #80091, .T. ) ; +#92548 = PLANE ( 'NONE', #86195 ) ; +#92549 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92550 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #79550 ) ) ; +#92551 = SURFACE_SIDE_STYLE ('',( #30263 ) ) ; +#92552 = ORIENTED_EDGE ( 'NONE', *, *, #10698, .F. ) ; +#92553 = ADVANCED_FACE ( 'NONE', ( #21374 ), #61216, .T. ) ; +#92554 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92555 = LINE ( 'NONE', #11509, #21719 ) ; +#92556 = VECTOR ( 'NONE', #1089, 1000.000000000000114 ) ; +#92557 = CARTESIAN_POINT ( 'NONE', ( 0.3549107142857130248, -0.9623376623376630468, 0.8100000000000001643 ) ) ; +#92558 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 1.149999999999999911, 0.000000000000000000 ) ) ; +#92559 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92560 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #92212 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#92561 = EDGE_CURVE ( 'NONE', #29318, #62323, #92313, .T. ) ; +#92562 = ORIENTED_EDGE ( 'NONE', *, *, #97835, .T. ) ; +#92563 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#92564 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92565 = EDGE_LOOP ( 'NONE', ( #67340, #72293, #18956, #83703 ) ) ; +#92566 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#92567 = PLANE ( 'NONE', #3134 ) ; +#92568 = FILL_AREA_STYLE_COLOUR ( '', #36280 ) ; +#92569 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59996 ), #56717 ) ; +#92570 = ORIENTED_EDGE ( 'NONE', *, *, #71484, .T. ) ; +#92571 = ADVANCED_FACE ( 'NONE', ( #77003 ), #82670, .T. ) ; +#92572 = ORIENTED_EDGE ( 'NONE', *, *, #95845, .T. ) ; +#92573 = EDGE_CURVE ( 'NONE', #78769, #95866, #62716, .T. ) ; +#92574 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98231, 'distance_accuracy_value', 'NONE'); +#92575 = VERTEX_POINT ( 'NONE', #62223 ) ; +#92576 = CIRCLE ( 'NONE', #17603, 0.04999999999999999584 ) ; +#92578 = ORIENTED_EDGE ( 'NONE', *, *, #23177, .T. ) ; +#92577 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92579 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79595 ), #30634 ) ; +#92580 = AXIS2_PLACEMENT_3D ( 'NONE', #65423, #96551, #81300 ) ; +#92581 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92583 = PLANE ( 'NONE', #85671 ) ; +#92582 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#92584 = FILL_AREA_STYLE_COLOUR ( '', #45483 ) ; +#92585 = ORIENTED_EDGE ( 'NONE', *, *, #89950, .T. ) ; +#92586 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#92587 = ORIENTED_EDGE ( 'NONE', *, *, #2855, .F. ) ; +#92588 = STYLED_ITEM ( 'NONE', ( #52519 ), #55437 ) ; +#92589 = CARTESIAN_POINT ( 'NONE', ( 0.4933869866146586292, 0.5990590759269652787, 0.8100000000000001643 ) ) ; +#92590 = EDGE_CURVE ( 'NONE', #47933, #64233, #87872, .T. ) ; +#92591 = PLANE ( 'NONE', #87226 ) ; +#92592 = ORIENTED_EDGE ( 'NONE', *, *, #54844, .T. ) ; +#92593 = ORIENTED_EDGE ( 'NONE', *, *, #54218, .T. ) ; +#92594 = EDGE_CURVE ( 'NONE', #1969, #100280, #8480, .T. ) ; +#92595 = SURFACE_SIDE_STYLE ('',( #70654 ) ) ; +#92596 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.5000000000000000000, 0.000000000000000000 ) ) ; +#92597 = VECTOR ( 'NONE', #53888, 1000.000000000000000 ) ; +#92598 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999556, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#92599 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97500 ), #19474 ) ; +#92600 = PLANE ( 'NONE', #87538 ) ; +#92601 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30663 ), #66543 ) ; +#92602 = VERTEX_POINT ( 'NONE', #86687 ) ; +#92604 = STYLED_ITEM ( 'NONE', ( #99286 ), #23463 ) ; +#92603 = SURFACE_STYLE_USAGE ( .BOTH. , #39029 ) ; +#92605 = VERTEX_POINT ( 'NONE', #71361 ) ; +#92606 = SURFACE_STYLE_USAGE ( .BOTH. , #76813 ) ; +#92607 = CLOSED_SHELL ( 'NONE', ( #60792, #62313, #15335, #91072, #93957, #29494 ) ) ; +#92608 = FILL_AREA_STYLE_COLOUR ( '', #16620 ) ; +#92609 = FILL_AREA_STYLE_COLOUR ( '', #91446 ) ; +#92610 = PRESENTATION_STYLE_ASSIGNMENT (( #53348 ) ) ; +#92611 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#92612 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.099999999999969891, -0.02000000000000000042 ) ) ; +#92613 = CARTESIAN_POINT ( 'NONE', ( 1.343425324675320054, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#92614 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.449999999999999956, -0.02000000000000000042 ) ) ; +#92615 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92616 = ORIENTED_EDGE ( 'NONE', *, *, #49652, .T. ) ; +#92617 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92618 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44093 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2878, #33004, #96760 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92619 = EDGE_CURVE ( 'NONE', #50837, #66469, #70866, .T. ) ; +#92622 = SURFACE_SIDE_STYLE ('',( #84003 ) ) ; +#92621 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92620 = FACE_OUTER_BOUND ( 'NONE', #22111, .T. ) ; +#92623 = SURFACE_SIDE_STYLE ('',( #89775 ) ) ; +#92624 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65671, 'distance_accuracy_value', 'NONE'); +#92625 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#92626 = LINE ( 'NONE', #77844, #62599 ) ; +#92627 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92628 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#92629 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 10.79220600000000019, 0.8648700000000000276 ) ) ; +#92630 = EDGE_CURVE ( 'NONE', #11665, #49190, #399, .T. ) ; +#92631 = EDGE_LOOP ( 'NONE', ( #87143, #63782, #82207, #3670, #15951, #92354 ) ) ; +#92632 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92633 = LINE ( 'NONE', #76843, #3766 ) ; +#92634 = CARTESIAN_POINT ( 'NONE', ( -0.04240146891761689685, -1.428263396816370046, 0.8100000000000000533 ) ) ; +#92635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #98991 ), #22560 ) ; +#92636 = FILL_AREA_STYLE ('',( #36571 ) ) ; +#92637 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92638 = FILL_AREA_STYLE_COLOUR ( '', #40237 ) ; +#92639 = FACE_OUTER_BOUND ( 'NONE', #45514, .T. ) ; +#92640 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66592 ), #76416 ) ; +#92641 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#92642 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92643 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#92644 = ADVANCED_FACE ( 'NONE', ( #32066 ), #15699, .T. ) ; +#92645 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 1.149999999999999911, 0.000000000000000000 ) ) ; +#92646 = LINE ( 'NONE', #86545, #82327 ) ; +#92647 = VECTOR ( 'NONE', #40911, 1000.000000000000000 ) ; +#92648 = CARTESIAN_POINT ( 'NONE', ( 6.367831750250086742, 10.54921475025008881, 0.8991599999999999593 ) ) ; +#92649 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10476 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11867, #34474, #27822 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92650 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78048 ) ) ; +#92651 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1238200612200849871, 0.000000000000000000 ) ) ; +#92652 = FACE_OUTER_BOUND ( 'NONE', #95923, .T. ) ; +#92653 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#92654 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92655 = CARTESIAN_POINT ( 'NONE', ( -1.284837223313930021, -1.093211113524890088, 0.8100000000000000533 ) ) ; +#92656 = VERTEX_POINT ( 'NONE', #100195 ) ; +#92657 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.000000000000000000 ) ) ; +#92658 = EDGE_CURVE ( 'NONE', #51947, #16445, #75828, .T. ) ; +#92659 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92660 = FILL_AREA_STYLE_COLOUR ( '', #63875 ) ; +#92662 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 8.300000000000000711, 0.000000000000000000 ) ) ; +#92661 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92663 = ORIENTED_EDGE ( 'NONE', *, *, #19654, .F. ) ; +#92664 = PLANE ( 'NONE', #93421 ) ; +#92665 = DIRECTION ( 'NONE', ( -0.7071060119555145906, -0.7071075504167436687, 0.000000000000000000 ) ) ; +#92666 = FILL_AREA_STYLE_COLOUR ( '', #19037 ) ; +#92667 = CIRCLE ( 'NONE', #25907, 0.04999999999999991257 ) ; +#92668 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52074 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26291, #18584, #34954 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92669 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#92670 = ADVANCED_FACE ( 'NONE', ( #28857 ), #13992, .T. ) ; +#92671 = ORIENTED_EDGE ( 'NONE', *, *, #81813, .T. ) ; +#92672 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92673 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78626 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68191, #66214, #36596 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92674 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29077, 'distance_accuracy_value', 'NONE'); +#92675 = AXIS2_PLACEMENT_3D ( 'NONE', #91252, #61141, #52465 ) ; +#92676 = EDGE_CURVE ( 'NONE', #10257, #38479, #36547, .T. ) ; +#92677 = ORIENTED_EDGE ( 'NONE', *, *, #62117, .F. ) ; +#92678 = EDGE_LOOP ( 'NONE', ( #44014, #76289, #73300, #50913 ) ) ; +#92679 = SURFACE_STYLE_FILL_AREA ( #15063 ) ; +#92680 = EDGE_LOOP ( 'NONE', ( #47801, #69493, #55599, #85701 ) ) ; +#92681 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40990 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #28019, #74475, #28496 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92682 = SURFACE_STYLE_USAGE ( .BOTH. , #84553 ) ; +#92683 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.429870129870129958, 0.8100000000000000533 ) ) ; +#92684 = LINE ( 'NONE', #60125, #17125 ) ; +#92685 = EDGE_CURVE ( 'NONE', #83312, #57616, #69117, .T. ) ; +#92687 = EDGE_CURVE ( 'NONE', #34142, #36359, #100685, .T. ) ; +#92686 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92688 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92689 = ORIENTED_EDGE ( 'NONE', *, *, #79045, .T. ) ; +#92691 = EDGE_CURVE ( 'NONE', #99759, #66922, #62042, .T. ) ; +#92690 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #34025 ) ) ; +#92692 = ORIENTED_EDGE ( 'NONE', *, *, #85578, .F. ) ; +#92693 = EDGE_CURVE ( 'NONE', #82338, #83860, #67640, .T. ) ; +#92694 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#92695 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78304, 'distance_accuracy_value', 'NONE'); +#92696 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.2999999999999999889, -12.64499999999999957 ) ) ; +#92697 = VERTEX_POINT ( 'NONE', #7306 ) ; +#92698 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#92699 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.73498000000000019, 0.8648700000000000276 ) ) ; +#92700 = CARTESIAN_POINT ( 'NONE', ( 1.355252715606880543E-17, 0.2500000001077751222, -4.336808749769470492E-19 ) ) ; +#92701 = ADVANCED_FACE ( 'NONE', ( #84980 ), #37045, .F. ) ; +#92702 = SURFACE_STYLE_USAGE ( .BOTH. , #100279 ) ; +#92703 = AXIS2_PLACEMENT_3D ( 'NONE', #11990, #61077, #90172 ) ; +#92705 = ORIENTED_EDGE ( 'NONE', *, *, #87998, .T. ) ; +#92704 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26922 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59143, #26969, #57634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92706 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92707 = ORIENTED_EDGE ( 'NONE', *, *, #75086, .F. ) ; +#92708 = ORIENTED_EDGE ( 'NONE', *, *, #42169, .F. ) ; +#92709 = CARTESIAN_POINT ( 'NONE', ( 1.363636363636359983, -1.336241883116880080, 0.8100000000000000533 ) ) ; +#92710 = ADVANCED_FACE ( 'NONE', ( #44624 ), #68616, .T. ) ; +#92711 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92712 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7831 ) ) ; +#92714 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#92713 = LINE ( 'NONE', #16119, #47869 ) ; +#92715 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, -0.000000000000000000 ) ) ; +#92717 = ORIENTED_EDGE ( 'NONE', *, *, #96411, .F. ) ; +#92716 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92718 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26584, #43389, #3088 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92719 = FILL_AREA_STYLE ('',( #47297 ) ) ; +#92720 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#92721 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71884 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #37358, #84783, #44460 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92722 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92723 = CARTESIAN_POINT ( 'NONE', ( 0.1681119866146560116, 0.5791465759269650571, 0.8100000000000001643 ) ) ; +#92724 = ORIENTED_EDGE ( 'NONE', *, *, #87904, .F. ) ; +#92725 = SURFACE_STYLE_FILL_AREA ( #61651 ) ; +#92726 = ORIENTED_EDGE ( 'NONE', *, *, #20924, .T. ) ; +#92727 = ORIENTED_EDGE ( 'NONE', *, *, #66548, .F. ) ; +#92728 = SURFACE_SIDE_STYLE ('',( #70277 ) ) ; +#92730 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#92729 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#92732 = VECTOR ( 'NONE', #87063, 1000.000000000000000 ) ; +#92731 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.4600000000000000200, -0.7999999999999999334 ) ) ; +#92733 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#92734 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.266666666666647068, 3.495651678170021751E-76 ) ) ; +#92735 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92736 = FILL_AREA_STYLE ('',( #39148 ) ) ; +#92737 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92738 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92739 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92740 = VECTOR ( 'NONE', #84603, 1000.000000000000000 ) ; +#92741 = ORIENTED_EDGE ( 'NONE', *, *, #68909, .F. ) ; +#92742 = ORIENTED_EDGE ( 'NONE', *, *, #63216, .F. ) ; +#92743 = AXIS2_PLACEMENT_3D ( 'NONE', #88018, #42062, #80375 ) ; +#92744 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#92745 = PRESENTATION_STYLE_ASSIGNMENT (( #32014 ) ) ; +#92746 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#92747 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #11147 ) ) ; +#92748 = FACE_OUTER_BOUND ( 'NONE', #19521, .T. ) ; +#92749 = LINE ( 'NONE', #7934, #61594 ) ; +#92750 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50427 ) ) ; +#92751 = ADVANCED_FACE ( 'NONE', ( #59017 ), #43138, .T. ) ; +#92752 = FILL_AREA_STYLE ('',( #63190 ) ) ; +#92753 = EDGE_LOOP ( 'NONE', ( #45842, #64364 ) ) ; +#92754 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92755 = SURFACE_STYLE_FILL_AREA ( #84633 ) ; +#92756 = LINE ( 'NONE', #76462, #63128 ) ; +#92757 = FACE_OUTER_BOUND ( 'NONE', #74950, .T. ) ; +#92758 = LINE ( 'NONE', #6461, #85510 ) ; +#92759 = VECTOR ( 'NONE', #43059, 1000.000000000000000 ) ; +#92760 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#92761 = LINE ( 'NONE', #38188, #11252 ) ; +#92762 = VECTOR ( 'NONE', #87554, 1000.000000000000000 ) ; +#92763 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#92764 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 11.25335600000000014, 0.8648700000000000276 ) ) ; +#92765 = PLANE ( 'NONE', #78039 ) ; +#92766 = LINE ( 'NONE', #7454, #81235 ) ; +#92767 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92768 = VECTOR ( 'NONE', #31046, 1000.000000000000000 ) ; +#92769 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 4.142826999999999593, 0.8991599999999999593 ) ) ; +#92770 = EDGE_LOOP ( 'NONE', ( #22668, #12773, #26049, #32021 ) ) ; +#92771 = SURFACE_STYLE_FILL_AREA ( #76988 ) ; +#92772 = EDGE_CURVE ( 'NONE', #98144, #80096, #13960, .T. ) ; +#92773 = FILL_AREA_STYLE ('',( #30491 ) ) ; +#92774 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#92775 = FACE_OUTER_BOUND ( 'NONE', #41076, .T. ) ; +#92776 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #19431 ) ) ; +#92777 = FILL_AREA_STYLE ('',( #7469 ) ) ; +#92778 = CARTESIAN_POINT ( 'NONE', ( 1.234625279613813076, -1.160211654383759727, 0.8099999999998891420 ) ) ; +#92779 = AXIS2_PLACEMENT_3D ( 'NONE', #29370, #86114, #91115 ) ; +#92780 = VECTOR ( 'NONE', #18187, 1000.000000000000000 ) ; +#92781 = SURFACE_SIDE_STYLE ('',( #23387 ) ) ; +#92782 = VERTEX_POINT ( 'NONE', #43627 ) ; +#92783 = FACE_OUTER_BOUND ( 'NONE', #100276, .T. ) ; +#92784 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58008 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10789, #73187, #55367 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92785 = CARTESIAN_POINT ( 'NONE', ( 1.698092532467530225, -1.219480519480520053, 0.8299999999999999600 ) ) ; +#92786 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #84042 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66957, #82303, #42974 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92787 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#92788 = SURFACE_SIDE_STYLE ('',( #69300 ) ) ; +#92789 = VERTEX_POINT ( 'NONE', #67120 ) ; +#92790 = ORIENTED_EDGE ( 'NONE', *, *, #89496, .T. ) ; +#92791 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#92792 = ORIENTED_EDGE ( 'NONE', *, *, #8987, .F. ) ; +#92793 = SURFACE_SIDE_STYLE ('',( #99879 ) ) ; +#92794 = FILL_AREA_STYLE_COLOUR ( '', #25435 ) ; +#92795 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 1.306104834246980087E-31 ) ) ; +#92796 = FILL_AREA_STYLE ('',( #61730 ) ) ; +#92797 = SHAPE_DEFINITION_REPRESENTATION ( #89757, #12210 ) ; +#92798 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.72722700000000096, 0.8648700000000000276 ) ) ; +#92799 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14597 ) ) ; +#92801 = ORIENTED_EDGE ( 'NONE', *, *, #98890, .F. ) ; +#92800 = ORIENTED_EDGE ( 'NONE', *, *, #52244, .F. ) ; +#92802 = STYLED_ITEM ( 'NONE', ( #87265 ), #1444 ) ; +#92803 = ORIENTED_EDGE ( 'NONE', *, *, #5300, .T. ) ; +#92804 = EDGE_CURVE ( 'NONE', #100629, #2612, #90100, .T. ) ; +#92805 = FILL_AREA_STYLE ('',( #55094 ) ) ; +#92806 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17432, 'distance_accuracy_value', 'NONE'); +#92807 = SURFACE_STYLE_FILL_AREA ( #63758 ) ; +#92809 = FILL_AREA_STYLE ('',( #61741 ) ) ; +#92808 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 1.983599999999999808, 0.8991599999999999593 ) ) ; +#92810 = EDGE_LOOP ( 'NONE', ( #76661, #87105, #96397, #79155 ) ) ; +#92811 = VERTEX_POINT ( 'NONE', #12424 ) ; +#92812 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999969802, -0.2999999999999999889, -0.02000000000000000042 ) ) ; +#92813 = FILL_AREA_STYLE ('',( #13173 ) ) ; +#92815 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92814 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92816 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74958 ) ) ; +#92817 = ORIENTED_EDGE ( 'NONE', *, *, #98589, .F. ) ; +#92818 = CARTESIAN_POINT ( 'NONE', ( -0.4517812530547630212, -1.032254439803430124, 0.8100000000000000533 ) ) ; +#92819 = ORIENTED_EDGE ( 'NONE', *, *, #76223, .T. ) ; +#92820 = ORIENTED_EDGE ( 'NONE', *, *, #74080, .F. ) ; +#92821 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99278 ), #50500 ) ; +#92822 = CARTESIAN_POINT ( 'NONE', ( 0.2550745812975909743, -1.387940725880749904, 0.8300000000000004041 ) ) ; +#92823 = ADVANCED_FACE ( 'NONE', ( #74800 ), #4826, .F. ) ; +#92824 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92825 = CARTESIAN_POINT ( 'NONE', ( -0.6323051948051949811, 0.7099999999999999645, 0.5000000000000000000 ) ) ; +#92827 = ORIENTED_EDGE ( 'NONE', *, *, #100589, .F. ) ; +#92826 = PRESENTATION_STYLE_ASSIGNMENT (( #84220 ) ) ; +#92828 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92829 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#92830 = FACE_OUTER_BOUND ( 'NONE', #48929, .T. ) ; +#92831 = VERTEX_POINT ( 'NONE', #93575 ) ; +#92832 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.67582000000000164, 0.8991599999999999593 ) ) ; +#92833 = ORIENTED_EDGE ( 'NONE', *, *, #34808, .T. ) ; +#92834 = EDGE_LOOP ( 'NONE', ( #39741, #19504, #99080, #22034 ) ) ; +#92835 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92836 = SURFACE_SIDE_STYLE ('',( #30567 ) ) ; +#92837 = VECTOR ( 'NONE', #59969, 1000.000000000000000 ) ; +#92838 = CARTESIAN_POINT ( 'NONE', ( -0.3774402512590340208, -1.154769547699080023, 0.8299999999999999600 ) ) ; +#92839 = FACE_OUTER_BOUND ( 'NONE', #35408, .T. ) ; +#92840 = SURFACE_STYLE_FILL_AREA ( #44397 ) ; +#92841 = CARTESIAN_POINT ( 'NONE', ( 1.055638970329410009, -1.181386160465649926, 0.8299999999999997380 ) ) ; +#92842 = STYLED_ITEM ( 'NONE', ( #26474 ), #85941 ) ; +#92843 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92844 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76841, 'distance_accuracy_value', 'NONE'); +#92845 = ADVANCED_FACE ( 'NONE', ( #46115 ), #77288, .F. ) ; +#92846 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#92847 = ORIENTED_EDGE ( 'NONE', *, *, #97293, .T. ) ; +#92848 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92849 = CARTESIAN_POINT ( 'NONE', ( 0.09337595685179390925, -1.316888414733939916, 0.8299999999999999600 ) ) ; +#92850 = ORIENTED_EDGE ( 'NONE', *, *, #30004, .T. ) ; +#92851 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#92853 = CARTESIAN_POINT ( 'NONE', ( -0.5013553533874209878, -0.9786196011214861601, 0.8299999999999998490 ) ) ; +#92852 = STYLED_ITEM ( 'NONE', ( #58896 ), #57170 ) ; +#92854 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45196 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97570, #57839, #65966 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92855 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92856 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4843 ) ) ; +#92857 = CARTESIAN_POINT ( 'NONE', ( 8.404299999999999216, 1.979081000000000090, 0.8991599999999999593 ) ) ; +#92859 = LINE ( 'NONE', #91894, #97224 ) ; +#92858 = AXIS2_PLACEMENT_3D ( 'NONE', #13242, #59838, #66942 ) ; +#92860 = CARTESIAN_POINT ( 'NONE', ( 1.705268638847220242, -0.9625006208768249749, 0.8100000000000000533 ) ) ; +#92861 = CARTESIAN_POINT ( 'NONE', ( 1.686404220779220031, -1.164935064935070042, 0.8100000000000000533 ) ) ; +#92862 = EDGE_CURVE ( 'NONE', #3678, #92789, #23188, .T. ) ; +#92863 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#92864 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92865 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #39172 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #57474, #9395, #80963 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92866 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92867 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31052 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14260, #53132, #28147 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92868 = FACE_OUTER_BOUND ( 'NONE', #87716, .T. ) ; +#92869 = SURFACE_SIDE_STYLE ('',( #30113 ) ) ; +#92870 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#92871 = SURFACE_STYLE_FILL_AREA ( #99961 ) ; +#92872 = STYLED_ITEM ( 'NONE', ( #92264 ), #64426 ) ; +#92873 = CARTESIAN_POINT ( 'NONE', ( 2.250000000000000444, 3.099999999999969891, 0.000000000000000000 ) ) ; +#92874 = SURFACE_STYLE_USAGE ( .BOTH. , #54125 ) ; +#92875 = STYLED_ITEM ( 'NONE', ( #58566 ), #1646 ) ; +#92876 = SURFACE_STYLE_FILL_AREA ( #100455 ) ; +#92877 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#92878 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27731 ) ) ; +#92879 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #58714 ), #73353 ) ; +#92880 = ORIENTED_EDGE ( 'NONE', *, *, #80725, .F. ) ; +#92881 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55220, 'distance_accuracy_value', 'NONE'); +#92882 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21347, 'distance_accuracy_value', 'NONE'); +#92883 = ADVANCED_FACE ( 'NONE', ( #70127 ), #8772, .F. ) ; +#92884 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92885 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#92886 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#92887 = LINE ( 'NONE', #70444, #20975 ) ; +#92888 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92889 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#92890 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19491 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #73487, #82159, #53015 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92891 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92892 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92893 = EDGE_CURVE ( 'NONE', #50590, #44609, #11294, .T. ) ; +#92894 = ORIENTED_EDGE ( 'NONE', *, *, #47841, .T. ) ; +#92895 = FACE_OUTER_BOUND ( 'NONE', #21830, .T. ) ; +#92896 = ORIENTED_EDGE ( 'NONE', *, *, #41389, .T. ) ; +#92897 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60714, 'distance_accuracy_value', 'NONE'); +#92899 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14039, 'distance_accuracy_value', 'NONE'); +#92900 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42397 ) ) ; +#92901 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92902 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92903 = CARTESIAN_POINT ( 'NONE', ( 5.628943999999999726, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#92904 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -1.050000000000000044 ) ) ; +#92905 = SURFACE_STYLE_FILL_AREA ( #34348 ) ; +#92906 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92907 = LINE ( 'NONE', #62337, #79490 ) ; +#92908 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92909 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#92910 = ORIENTED_EDGE ( 'NONE', *, *, #57628, .F. ) ; +#92911 = EDGE_CURVE ( 'NONE', #83615, #56071, #2734, .T. ) ; +#92912 = CARTESIAN_POINT ( 'NONE', ( 1.186064574101910019, -0.9547617453595670378, 0.8300000000000002931 ) ) ; +#92913 = EDGE_CURVE ( 'NONE', #10584, #92697, #75423, .T. ) ; +#92914 = ORIENTED_EDGE ( 'NONE', *, *, #57276, .T. ) ; +#92915 = SURFACE_STYLE_USAGE ( .BOTH. , #46995 ) ; +#92916 = AXIS2_PLACEMENT_3D ( 'NONE', #53658, #92908, #84781 ) ; +#92917 = ORIENTED_EDGE ( 'NONE', *, *, #95542, .F. ) ; +#92918 = CARTESIAN_POINT ( 'NONE', ( 1.089738207395029912, -1.411115659170130154, 0.8299999999999999600 ) ) ; +#92919 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#92920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39175 ) ) ; +#92921 = VECTOR ( 'NONE', #48953, 1000.000000000000000 ) ; +#92922 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#92923 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92924 = CARTESIAN_POINT ( 'NONE', ( 1.810920360744870061, -1.177156496261070107, 0.8100000000000000533 ) ) ; +#92925 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999949907, -1.876179938779915179, 0.000000000000000000 ) ) ; +#92926 = CARTESIAN_POINT ( 'NONE', ( 0.09276726147040417758, 0.9553828707289927502, 0.8100000000000001643 ) ) ; +#92928 = VERTEX_POINT ( 'NONE', #96120 ) ; +#92927 = ORIENTED_EDGE ( 'NONE', *, *, #39591, .F. ) ; +#92929 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92930 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92931 = ORIENTED_EDGE ( 'NONE', *, *, #93880, .T. ) ; +#92932 = ADVANCED_FACE ( 'NONE', ( #17510 ), #41536, .T. ) ; +#92933 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#92934 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#92935 = ORIENTED_EDGE ( 'NONE', *, *, #15410, .F. ) ; +#92936 = ORIENTED_EDGE ( 'NONE', *, *, #44061, .F. ) ; +#92937 = VECTOR ( 'NONE', #69597, 1000.000000000000114 ) ; +#92938 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92939 = SURFACE_STYLE_USAGE ( .BOTH. , #93453 ) ; +#92940 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#92941 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78347 ), #21262 ) ; +#92942 = FACE_OUTER_BOUND ( 'NONE', #67487, .T. ) ; +#92943 = SURFACE_STYLE_USAGE ( .BOTH. , #61868 ) ; +#92944 = ORIENTED_EDGE ( 'NONE', *, *, #3593, .T. ) ; +#92945 = ORIENTED_EDGE ( 'NONE', *, *, #63512, .T. ) ; +#92946 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#92947 = ORIENTED_EDGE ( 'NONE', *, *, #7600, .F. ) ; +#92948 = FILL_AREA_STYLE ('',( #6648 ) ) ; +#92949 = EDGE_CURVE ( 'NONE', #44461, #23149, #49718, .T. ) ; +#92950 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #16358 ), #45719 ) ; +#92951 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35959 ), #96257 ) ; +#92953 = ORIENTED_EDGE ( 'NONE', *, *, #58920, .F. ) ; +#92952 = DIRECTION ( 'NONE', ( 0.7071060119555140355, 0.7071075504167442238, 0.000000000000000000 ) ) ; +#92954 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70456 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76214, #84869, #36925 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92955 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#92956 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#92957 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 1.474514954580256140E-18, -0.8499999999999999778 ) ) ; +#92958 = ORIENTED_EDGE ( 'NONE', *, *, #97094, .T. ) ; +#92959 = LINE ( 'NONE', #38395, #63101 ) ; +#92960 = PRESENTATION_STYLE_ASSIGNMENT (( #566 ) ) ; +#92961 = EDGE_LOOP ( 'NONE', ( #84727, #66509, #39768, #85294 ) ) ; +#92962 = SURFACE_STYLE_USAGE ( .BOTH. , #31225 ) ; +#92963 = LINE ( 'NONE', #22559, #23707 ) ; +#92964 = AXIS2_PLACEMENT_3D ( 'NONE', #81040, #90682, #10973 ) ; +#92966 = VERTEX_POINT ( 'NONE', #18531 ) ; +#92965 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#92967 = VECTOR ( 'NONE', #57566, 1000.000000000000000 ) ; +#92969 = SURFACE_STYLE_FILL_AREA ( #1097 ) ; +#92968 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4749999999999999778, 0.2500000000000000000 ) ) ; +#92970 = CARTESIAN_POINT ( 'NONE', ( -1.077778692506025759, -1.170256537188258505, 0.8099999999998624967 ) ) ; +#92971 = EDGE_CURVE ( 'NONE', #35510, #60355, #32875, .T. ) ; +#92972 = FILL_AREA_STYLE_COLOUR ( '', #53984 ) ; +#92973 = FACE_OUTER_BOUND ( 'NONE', #21042, .T. ) ; +#92974 = ORIENTED_EDGE ( 'NONE', *, *, #92435, .T. ) ; +#92975 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#92976 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#92977 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#92978 = CARTESIAN_POINT ( 'NONE', ( 1.678890544094119974, -1.445107798742939931, 0.8100000000000000533 ) ) ; +#92979 = LINE ( 'NONE', #31245, #60098 ) ; +#92980 = SURFACE_SIDE_STYLE ('',( #84847 ) ) ; +#92981 = EDGE_CURVE ( 'NONE', #90656, #36176, #56385, .T. ) ; +#92982 = CARTESIAN_POINT ( 'NONE', ( 9.568127000000000493, 10.55639900000000075, 0.8991599999999999593 ) ) ; +#92983 = AXIS2_PLACEMENT_3D ( 'NONE', #22194, #54360, #45630 ) ; +#92984 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#92985 = EDGE_LOOP ( 'NONE', ( #57637, #53436, #24217, #36104 ) ) ; +#92986 = CARTESIAN_POINT ( 'NONE', ( 3.560618999999999978, 6.822763000000000133, 0.8991599999999999593 ) ) ; +#92987 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#92988 = VECTOR ( 'NONE', #77304, 1000.000000000000000 ) ; +#92989 = STYLED_ITEM ( 'NONE', ( #69630 ), #93816 ) ; +#92990 = ORIENTED_EDGE ( 'NONE', *, *, #11515, .F. ) ; +#92991 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17928 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61185, #77985, #15662 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#92992 = SURFACE_STYLE_FILL_AREA ( #93507 ) ; +#92993 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#92994 = STYLED_ITEM ( 'NONE', ( #69222 ), #57743 ) ; +#92995 = SURFACE_STYLE_USAGE ( .BOTH. , #78721 ) ; +#92996 = ORIENTED_EDGE ( 'NONE', *, *, #18728, .F. ) ; +#92997 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#92998 = VECTOR ( 'NONE', #70758, 1000.000000000000000 ) ; +#92999 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93000 = CARTESIAN_POINT ( 'NONE', ( -0.03429546097047749681, -1.132325613921520091, 0.8300000000000005151 ) ) ; +#93001 = PRESENTATION_STYLE_ASSIGNMENT (( #86918 ) ) ; +#93002 = PRESENTATION_STYLE_ASSIGNMENT (( #61933 ) ) ; +#93003 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93004 = CARTESIAN_POINT ( 'NONE', ( 0.9586437380306700451, -1.309512843728070086, 0.8300000000000010703 ) ) ; +#93005 = CARTESIAN_POINT ( 'NONE', ( 2.649999999999999911, -3.099999999999960121, 0.000000000000000000 ) ) ; +#93006 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990585, 0.000000000000000000 ) ) ; +#93007 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #18030 ) ) ; +#93008 = PRESENTATION_STYLE_ASSIGNMENT (( #6216 ) ) ; +#93009 = EDGE_CURVE ( 'NONE', #95882, #82544, #2231, .T. ) ; +#93010 = EDGE_CURVE ( 'NONE', #88016, #55998, #79840, .T. ) ; +#93011 = PRESENTATION_STYLE_ASSIGNMENT (( #61942 ) ) ; +#93012 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24710, 'distance_accuracy_value', 'NONE'); +#93013 = PLANE ( 'NONE', #6063 ) ; +#93014 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93015 = VECTOR ( 'NONE', #2776, 1000.000000000000000 ) ; +#93016 = ORIENTED_EDGE ( 'NONE', *, *, #20541, .T. ) ; +#93017 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4849999999999999867, 0.000000000000000000 ) ) ; +#93018 = ORIENTED_EDGE ( 'NONE', *, *, #96774, .F. ) ; +#93019 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#93020 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86889, 'distance_accuracy_value', 'NONE'); +#93021 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #50600, 'distance_accuracy_value', 'NONE'); +#93022 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93023 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000010214, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#93024 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#93025 = FACE_OUTER_BOUND ( 'NONE', #63729, .T. ) ; +#93026 = DIRECTION ( 'NONE', ( 1.000000000000000000, 7.400903063771439863E-81, 8.347776819438500435E-49 ) ) ; +#93027 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93028 = LINE ( 'NONE', #94034, #66797 ) ; +#93029 = CARTESIAN_POINT ( 'NONE', ( 5.696081000000000394, 3.570070999999999994, 0.8648700000000000276 ) ) ; +#93030 = ORIENTED_EDGE ( 'NONE', *, *, #70813, .F. ) ; +#93031 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, 0.000000000000000000 ) ) ; +#93032 = EDGE_CURVE ( 'NONE', #24225, #65172, #89001, .T. ) ; +#93033 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93034 = SURFACE_STYLE_USAGE ( .BOTH. , #6719 ) ; +#93035 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98577, 'distance_accuracy_value', 'NONE'); +#93036 = EDGE_CURVE ( 'NONE', #83675, #4203, #25716, .T. ) ; +#93037 = LINE ( 'NONE', #38965, #49288 ) ; +#93038 = ORIENTED_EDGE ( 'NONE', *, *, #88579, .F. ) ; +#93039 = CARTESIAN_POINT ( 'NONE', ( 1.362811107210154971, -1.311384449581630252, 0.8099999999997941069 ) ) ; +#93040 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93041 = ORIENTED_EDGE ( 'NONE', *, *, #26816, .F. ) ; +#93042 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53953 ), #76602 ) ; +#93043 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19934, #34286, #4113, #64892, #88376, #2616, #89874, #81748, #42917 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999993339, 0.3749999999999991118, 0.4999999999999988898, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#93044 = PRESENTATION_STYLE_ASSIGNMENT (( #74892 ) ) ; +#93045 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.01000000000000000021, -0.2250000000000000333 ) ) ; +#93046 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93047 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#93048 = VERTEX_POINT ( 'NONE', #81371 ) ; +#93049 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #71487 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78158, #8104, #47500 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93050 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91558, 'distance_accuracy_value', 'NONE'); +#93051 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#93052 = EDGE_CURVE ( 'NONE', #49190, #97600, #17010, .T. ) ; +#93053 = SHAPE_REPRESENTATION ( 'DFN1006.xtd', ( #82894 ), #38598 ) ; +#93054 = ORIENTED_EDGE ( 'NONE', *, *, #84061, .T. ) ; +#93055 = EDGE_CURVE ( 'NONE', #74624, #44343, #40537, .T. ) ; +#93056 = SURFACE_STYLE_USAGE ( .BOTH. , #30802 ) ; +#93057 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1431 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2254, #64029, #18025 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93058 = SURFACE_STYLE_USAGE ( .BOTH. , #47141 ) ; +#93059 = SURFACE_SIDE_STYLE ('',( #61991 ) ) ; +#93060 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -0.8333333333333353687, 0.000000000000000000 ) ) ; +#93061 = ORIENTED_EDGE ( 'NONE', *, *, #14004, .F. ) ; +#93062 = ORIENTED_EDGE ( 'NONE', *, *, #40810, .T. ) ; +#93063 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93064 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #54418 ) ; +#93065 = VERTEX_POINT ( 'NONE', #12816 ) ; +#93066 = STYLED_ITEM ( 'NONE', ( #28977 ), #86682 ) ; +#93067 = EDGE_CURVE ( 'NONE', #57623, #54091, #55928, .T. ) ; +#93068 = VECTOR ( 'NONE', #71719, 1000.000000000000000 ) ; +#93069 = EDGE_CURVE ( 'NONE', #71164, #3341, #67488, .T. ) ; +#93070 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93071 = ORIENTED_EDGE ( 'NONE', *, *, #6422, .T. ) ; +#93073 = EDGE_LOOP ( 'NONE', ( #45485, #33975, #39662, #81934, #86209, #14948, #33588, #41507 ) ) ; +#93072 = FACE_OUTER_BOUND ( 'NONE', #15756, .T. ) ; +#93074 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16480 ) ) ; +#93075 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#93077 = PRESENTATION_STYLE_ASSIGNMENT (( #62002 ) ) ; +#93076 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93078 = VERTEX_POINT ( 'NONE', #92825 ) ; +#93079 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93080 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, 0.1350000000000000089 ) ) ; +#93081 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.123820061220075051, 0.000000000000000000 ) ) ; +#93082 = ORIENTED_EDGE ( 'NONE', *, *, #92510, .F. ) ; +#93083 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39325 ), #16491 ) ; +#93084 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000000021, 0.7833333856764529424, 0.6832601739883094050 ) ) ; +#93085 = PRESENTATION_STYLE_ASSIGNMENT (( #62010 ) ) ; +#93086 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93087 = ORIENTED_EDGE ( 'NONE', *, *, #70960, .T. ) ; +#93088 = SURFACE_STYLE_FILL_AREA ( #85975 ) ; +#93089 = ORIENTED_EDGE ( 'NONE', *, *, #100663, .F. ) ; +#93091 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93090 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93092 = VECTOR ( 'NONE', #37435, 1000.000000000000000 ) ; +#93093 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93094 = EDGE_CURVE ( 'NONE', #14404, #55177, #98561, .T. ) ; +#93095 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93096 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 15.15000000000000036, 0.000000000000000000 ) ) ; +#93097 = ORIENTED_EDGE ( 'NONE', *, *, #12067, .T. ) ; +#93098 = LINE ( 'NONE', #6778, #71053 ) ; +#93099 = EDGE_LOOP ( 'NONE', ( #24816, #34385, #21379, #35886 ) ) ; +#93101 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.425188158846549879E-32, -2.567390744445670062E-16 ) ) ; +#93100 = FILL_AREA_STYLE_COLOUR ( '', #62497 ) ; +#93102 = CARTESIAN_POINT ( 'NONE', ( 5.823360000000000092, 9.085504000000002023, 0.8648700000000000276 ) ) ; +#93103 = EDGE_CURVE ( 'NONE', #79041, #57616, #27234, .T. ) ; +#93104 = CARTESIAN_POINT ( 'NONE', ( 8.093173000000000172, 6.264148000000000494, 0.8991599999999999593 ) ) ; +#93105 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43845, 'distance_accuracy_value', 'NONE'); +#93106 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9902 ), #94733 ) ; +#93107 = EDGE_CURVE ( 'NONE', #68209, #89849, #60915, .T. ) ; +#93108 = CARTESIAN_POINT ( 'NONE', ( 10.10135599999999911, 8.852159000000000333, 0.8991599999999999593 ) ) ; +#93109 = STYLED_ITEM ( 'NONE', ( #14702 ), #46120 ) ; +#93110 = DIRECTION ( 'NONE', ( 2.673953023792510104E-26, -7.363535408886330351E-13, 1.000000000000000000 ) ) ; +#93111 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#93112 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 2.299999999999999822, 0.000000000000000000 ) ) ; +#93113 = VERTEX_POINT ( 'NONE', #59400 ) ; +#93114 = SURFACE_STYLE_FILL_AREA ( #16529 ) ; +#93115 = PRESENTATION_STYLE_ASSIGNMENT (( #85999 ) ) ; +#93117 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93116 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#93118 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93119 = STYLED_ITEM ( 'NONE', ( #51311 ), #45589 ) ; +#93120 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.289444213855800265E-17, -0.8499999999999999778 ) ) ; +#93121 = CARTESIAN_POINT ( 'NONE', ( -2.549999999999999822, -3.100000000000000533, -0.02000000000000000042 ) ) ; +#93122 = LINE ( 'NONE', #92628, #45274 ) ; +#93123 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93124 = SURFACE_SIDE_STYLE ('',( #30874 ) ) ; +#93125 = EDGE_LOOP ( 'NONE', ( #71385, #99813, #47541, #52782 ) ) ; +#93126 = CARTESIAN_POINT ( 'NONE', ( -2.523820061220085176, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#93127 = SURFACE_STYLE_FILL_AREA ( #15011 ) ; +#93128 = CARTESIAN_POINT ( 'NONE', ( -0.0005258701502700120420, -1.389839611604140046, 0.8100000000000000533 ) ) ; +#93129 = VECTOR ( 'NONE', #34308, 1000.000000000000000 ) ; +#93130 = VECTOR ( 'NONE', #16842, 1000.000000000000000 ) ; +#93131 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 0.6999999999999990674, 5.234185452379087911E-79 ) ) ; +#93132 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8991599999999999593 ) ) ; +#93133 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#93134 = FILL_AREA_STYLE ('',( #62070 ) ) ; +#93135 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93137 = ADVANCED_FACE ( 'NONE', ( #36384 ), #75671, .T. ) ; +#93136 = FACE_OUTER_BOUND ( 'NONE', #67854, .T. ) ; +#93138 = EDGE_CURVE ( 'NONE', #68985, #71780, #5681, .T. ) ; +#93139 = VECTOR ( 'NONE', #76440, 1000.000000000000000 ) ; +#93140 = FILL_AREA_STYLE ('',( #22741 ) ) ; +#93141 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32853 ) ) ; +#93142 = LINE ( 'NONE', #76349, #50535 ) ; +#93143 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93144 = SURFACE_STYLE_USAGE ( .BOTH. , #38566 ) ; +#93145 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#93146 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#93147 = ORIENTED_EDGE ( 'NONE', *, *, #77726, .F. ) ; +#93148 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1916, 'distance_accuracy_value', 'NONE'); +#93149 = AXIS2_PLACEMENT_3D ( 'NONE', #12963, #28854, #67636 ) ; +#93150 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 2.850000000000000089, 0.03429000000000000103 ) ) ; +#93151 = CARTESIAN_POINT ( 'NONE', ( -0.3115761583028878734, -1.344927722445946161, 0.8099999999997308242 ) ) ; +#93152 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45089, 'distance_accuracy_value', 'NONE'); +#93153 = FILL_AREA_STYLE ('',( #14535 ) ) ; +#93154 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93155 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93156 = CARTESIAN_POINT ( 'NONE', ( -1.219528525021920107, -1.135808780994409961, 0.8299999999999999600 ) ) ; +#93157 = EDGE_LOOP ( 'NONE', ( #12184, #29214, #19167, #64843 ) ) ; +#93158 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93159 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93160 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60375, 'distance_accuracy_value', 'NONE'); +#93161 = EDGE_CURVE ( 'NONE', #52188, #90644, #61763, .T. ) ; +#93162 = PRESENTATION_STYLE_ASSIGNMENT (( #70721 ) ) ; +#93163 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93164 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6219 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75993, #30494, #29531 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93165 = VERTEX_POINT ( 'NONE', #66017 ) ; +#93166 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999939493, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#93167 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93168 = STYLED_ITEM ( 'NONE', ( #65604 ), #2636 ) ; +#93169 = DIRECTION ( 'NONE', ( -0.7071045084557415761, 0.7071090539100487460, 0.000000000000000000 ) ) ; +#93170 = SURFACE_STYLE_USAGE ( .BOTH. , #38098 ) ; +#93171 = ORIENTED_EDGE ( 'NONE', *, *, #17721, .F. ) ; +#93172 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.850000000000000089, -0.02000000000000000042 ) ) ; +#93173 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93263, 'distance_accuracy_value', 'NONE'); +#93174 = CARTESIAN_POINT ( 'NONE', ( -0.06452060059824049620, -1.437850337629750008, 0.8300000000000006262 ) ) ; +#93175 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43713, #98774, #99274 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93176 = ORIENTED_EDGE ( 'NONE', *, *, #38316, .T. ) ; +#93177 = ORIENTED_EDGE ( 'NONE', *, *, #80294, .F. ) ; +#93178 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93179 = SURFACE_STYLE_USAGE ( .BOTH. , #62119 ) ; +#93180 = ORIENTED_EDGE ( 'NONE', *, *, #63007, .F. ) ; +#93181 = STYLED_ITEM ( 'NONE', ( #41101 ), #51940 ) ; +#93182 = CARTESIAN_POINT ( 'NONE', ( 0.09335570779574380029, -1.336905478629369926, 0.8100000000000000533 ) ) ; +#93183 = DIRECTION ( 'NONE', ( 5.551115123125780237E-17, -1.000000000000000000, 5.551115123125780237E-17 ) ) ; +#93184 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.7000000000000009548, -0.02000000000002233672 ) ) ; +#93185 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#93186 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #53481, #61511 ) ; +#93187 = CARTESIAN_POINT ( 'NONE', ( 0.2415584415584410005, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#93188 = EDGE_CURVE ( 'NONE', #52561, #56601, #58392, .T. ) ; +#93189 = AXIS2_PLACEMENT_3D ( 'NONE', #17488, #54822, #56360 ) ; +#93190 = ORIENTED_EDGE ( 'NONE', *, *, #79613, .T. ) ; +#93191 = SURFACE_SIDE_STYLE ('',( #8889 ) ) ; +#93192 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#93193 = LINE ( 'NONE', #54461, #17145 ) ; +#93194 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93195 = ORIENTED_EDGE ( 'NONE', *, *, #97498, .F. ) ; +#93196 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.01500000000000000118, 0.1400000000000000133 ) ) ; +#93197 = CYLINDRICAL_SURFACE ( 'NONE', #46298, 0.04999999999999991257 ) ; +#93198 = VECTOR ( 'NONE', #94827, 1000.000000000000000 ) ; +#93199 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#93200 = ORIENTED_EDGE ( 'NONE', *, *, #76609, .F. ) ; +#93201 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #38901, #15887, #56774, #25610 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#93203 = SURFACE_STYLE_FILL_AREA ( #62143 ) ; +#93202 = FACE_OUTER_BOUND ( 'NONE', #94482, .T. ) ; +#93204 = VERTEX_POINT ( 'NONE', #27739 ) ; +#93205 = VERTEX_POINT ( 'NONE', #11786 ) ; +#93206 = FACE_OUTER_BOUND ( 'NONE', #86206, .T. ) ; +#93207 = STYLED_ITEM ( 'NONE', ( #68134 ), #87049 ) ; +#93208 = VECTOR ( 'NONE', #69411, 1000.000000000000000 ) ; +#93209 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#93211 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#93210 = CARTESIAN_POINT ( 'NONE', ( 0.5376623376623369532, -1.437662337662340084, 0.8299999999999999600 ) ) ; +#93212 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93213 = EDGE_CURVE ( 'NONE', #81528, #61768, #58898, .T. ) ; +#93214 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#93215 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93216 = VERTEX_POINT ( 'NONE', #51212 ) ; +#93217 = PLANE ( 'NONE', #98748 ) ; +#93218 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93219 = LINE ( 'NONE', #93718, #33653 ) ; +#93220 = FILL_AREA_STYLE ('',( #62154 ) ) ; +#93221 = STYLED_ITEM ( 'NONE', ( #66254 ), #10889 ) ; +#93222 = ORIENTED_EDGE ( 'NONE', *, *, #93966, .F. ) ; +#93224 = SURFACE_STYLE_USAGE ( .BOTH. , #22831 ) ; +#93223 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, 0.7099999999999999645, 0.8000000000000000444 ) ) ; +#93225 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#93226 = ORIENTED_EDGE ( 'NONE', *, *, #2766, .T. ) ; +#93227 = ORIENTED_EDGE ( 'NONE', *, *, #912, .F. ) ; +#93228 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#93230 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#93229 = FACE_OUTER_BOUND ( 'NONE', #69015, .T. ) ; +#93231 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93232 = ADVANCED_FACE ( 'NONE', ( #82350 ), #74690, .T. ) ; +#93233 = AXIS2_PLACEMENT_3D ( 'NONE', #73568, #28599, #80744 ) ; +#93234 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.1600000000000000033, 1.250000000000000000 ) ) ; +#93235 = PLANE ( 'NONE', #44818 ) ; +#93236 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93237 = DIRECTION ( 'NONE', ( -0.7071045084557444627, -0.7071090539100457484, 0.000000000000000000 ) ) ; +#93238 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93239 = SURFACE_SIDE_STYLE ('',( #60650 ) ) ; +#93240 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65505 ) ) ; +#93241 = ORIENTED_EDGE ( 'NONE', *, *, #11209, .T. ) ; +#93242 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93243 = VERTEX_POINT ( 'NONE', #16745 ) ; +#93244 = EDGE_CURVE ( 'NONE', #69571, #44986, #7517, .T. ) ; +#93245 = STYLED_ITEM ( 'NONE', ( #50233 ), #70116 ) ; +#93246 = SURFACE_SIDE_STYLE ('',( #30995 ) ) ; +#93247 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, 1.048695503451053346E-76 ) ) ; +#93248 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93249 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 3.200000000000000178, 0.03429000000000000103 ) ) ; +#93250 = FILL_AREA_STYLE ('',( #85627 ) ) ; +#93251 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36249 ), #13323 ) ; +#93252 = EDGE_CURVE ( 'NONE', #60413, #212, #94367, .T. ) ; +#93253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93254 = ORIENTED_EDGE ( 'NONE', *, *, #71549, .F. ) ; +#93255 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93256 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33032 ), #62345 ) ; +#93257 = FILL_AREA_STYLE ('',( #31010 ) ) ; +#93258 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36825 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79262, #24664, #32794 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93259 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93260 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16323, 'distance_accuracy_value', 'NONE'); +#93261 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, -3.500000000000000444, 0.000000000000000000 ) ) ; +#93262 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39434 ) ) ; +#93264 = EDGE_CURVE ( 'NONE', #46126, #50925, #442, .T. ) ; +#93263 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93265 = ADVANCED_FACE ( 'NONE', ( #70381 ), #71926, .T. ) ; +#93266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93267 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93268 = STYLED_ITEM ( 'NONE', ( #82083 ), #82012 ) ; +#93269 = LINE ( 'NONE', #69273, #32298 ) ; +#93270 = EDGE_CURVE ( 'NONE', #42026, #53923, #17267, .T. ) ; +#93271 = ADVANCED_FACE ( 'NONE', ( #100892 ), #31092, .T. ) ; +#93272 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93273 = CARTESIAN_POINT ( 'NONE', ( 3.744100000000000428, 10.73498000000000019, 0.8991599999999999593 ) ) ; +#93274 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #99751 ), #75385 ) ; +#93275 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93276 = LINE ( 'NONE', #47359, #34616 ) ; +#93277 = VERTEX_POINT ( 'NONE', #65255 ) ; +#93278 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.59270000000000067, 0.8991599999999999593 ) ) ; +#93279 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#93280 = CARTESIAN_POINT ( 'NONE', ( 11.21151312487495666, 5.705533124874956563, 0.8648700000000000276 ) ) ; +#93281 = ADVANCED_FACE ( 'NONE', ( #3975 ), #81110, .T. ) ; +#93282 = PLANE ( 'NONE', #39586 ) ; +#93283 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81975 ), #54191 ) ; +#93284 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71039, 'distance_accuracy_value', 'NONE'); +#93285 = FILL_AREA_STYLE ('',( #5502 ) ) ; +#93286 = CARTESIAN_POINT ( 'NONE', ( 11.51556899999999928, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#93287 = CARTESIAN_POINT ( 'NONE', ( 1.193775255294553528, -1.151210320156312639, 0.8099999999998946931 ) ) ; +#93288 = EDGE_CURVE ( 'NONE', #48436, #13319, #43276, .T. ) ; +#93289 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52286 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52290, #37953, #68058 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93290 = STYLED_ITEM ( 'NONE', ( #5760 ), #96326 ) ; +#93291 = ORIENTED_EDGE ( 'NONE', *, *, #32039, .T. ) ; +#93292 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000013115, -0.1499999999999999944 ) ) ; +#93293 = AXIS2_PLACEMENT_3D ( 'NONE', #65487, #65005, #94607 ) ; +#93294 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#93295 = LINE ( 'NONE', #32065, #93431 ) ; +#93296 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93297 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #78115, 'distance_accuracy_value', 'NONE'); +#93298 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36296 ) ) ; +#93299 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74650, 'distance_accuracy_value', 'NONE'); +#93300 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93301 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85128 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74463, #27502, #26494 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93302 = VERTEX_POINT ( 'NONE', #57643 ) ; +#93303 = ORIENTED_EDGE ( 'NONE', *, *, #22551, .F. ) ; +#93304 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93305 = VECTOR ( 'NONE', #57079, 1000.000000000000000 ) ; +#93306 = ORIENTED_EDGE ( 'NONE', *, *, #50387, .F. ) ; +#93307 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93308 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93309 = LINE ( 'NONE', #76509, #48363 ) ; +#93310 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9342, 'distance_accuracy_value', 'NONE'); +#93311 = PLANE ( 'NONE', #85484 ) ; +#93312 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11954 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #98028, #53159, #74634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93313 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #78877 ) ; +#93314 = SURFACE_STYLE_FILL_AREA ( #47395 ) ; +#93316 = VERTEX_POINT ( 'NONE', #27478 ) ; +#93315 = ORIENTED_EDGE ( 'NONE', *, *, #26542, .T. ) ; +#93317 = EDGE_CURVE ( 'NONE', #26591, #66220, #12053, .T. ) ; +#93318 = VERTEX_POINT ( 'NONE', #19805 ) ; +#93319 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93320 = DIRECTION ( 'NONE', ( -0.7071067816865476141, -0.7071067806865475314, 0.000000000000000000 ) ) ; +#93322 = PRESENTATION_STYLE_ASSIGNMENT (( #78051 ) ) ; +#93321 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -2.433333333333333570, 0.000000000000000000 ) ) ; +#93323 = VERTEX_POINT ( 'NONE', #4465 ) ; +#93324 = VECTOR ( 'NONE', #16320, 1000.000000000000000 ) ; +#93325 = ADVANCED_FACE ( 'NONE', ( #35658 ), #50969, .T. ) ; +#93326 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999939959, -2.700000000000000178, -0.02000000000002725292 ) ) ; +#93327 = SURFACE_SIDE_STYLE ('',( #428 ) ) ; +#93328 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#93329 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93330 = ORIENTED_EDGE ( 'NONE', *, *, #61516, .F. ) ; +#93331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93332 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#93333 = ORIENTED_EDGE ( 'NONE', *, *, #71299, .F. ) ; +#93334 = ORIENTED_EDGE ( 'NONE', *, *, #26392, .T. ) ; +#93335 = SURFACE_STYLE_USAGE ( .BOTH. , #71409 ) ; +#93336 = SURFACE_STYLE_USAGE ( .BOTH. , #62763 ) ; +#93338 = ORIENTED_EDGE ( 'NONE', *, *, #98666, .T. ) ; +#93337 = CARTESIAN_POINT ( 'NONE', ( -0.1968215468279112534, -1.443505376027208520, 0.8099999999995833866 ) ) ; +#93339 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#93340 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93341 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93342 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10347 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #2417, #78128, #55180 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93343 = VERTEX_POINT ( 'NONE', #37147 ) ; +#93345 = FILL_AREA_STYLE ('',( #33123 ) ) ; +#93344 = PLANE ( 'NONE', #4148 ) ; +#93346 = FILL_AREA_STYLE_COLOUR ( '', #55843 ) ; +#93347 = VERTEX_POINT ( 'NONE', #13062 ) ; +#93348 = ORIENTED_EDGE ( 'NONE', *, *, #28044, .F. ) ; +#93349 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.2250000000000000333 ) ) ; +#93350 = EDGE_CURVE ( 'NONE', #78683, #44592, #91247, .T. ) ; +#93351 = LINE ( 'NONE', #9555, #84081 ) ; +#93352 = AXIS2_PLACEMENT_3D ( 'NONE', #52428, #84550, #98792 ) ; +#93353 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93354 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93355 = VECTOR ( 'NONE', #80742, 1000.000000000000000 ) ; +#93356 = FILL_AREA_STYLE_COLOUR ( '', #55973 ) ; +#93357 = AXIS2_PLACEMENT_3D ( 'NONE', #75140, #89446, #66458 ) ; +#93358 = CARTESIAN_POINT ( 'NONE', ( 1.303722762681589931, -1.254158608853950030, 0.8299999999999997380 ) ) ; +#93359 = AXIS2_PLACEMENT_3D ( 'NONE', #93029, #23645, #77240 ) ; +#93360 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93361 = VERTEX_POINT ( 'NONE', #13562 ) ; +#93362 = EDGE_LOOP ( 'NONE', ( #4925, #64142, #86741, #78205 ) ) ; +#93363 = AXIS2_PLACEMENT_3D ( 'NONE', #95488, #87858, #25594 ) ; +#93364 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93365 = CARTESIAN_POINT ( 'NONE', ( -0.4771637165632133804, -0.9965848524479249404, 0.8300000000000000711 ) ) ; +#93366 = SURFACE_STYLE_USAGE ( .BOTH. , #6567 ) ; +#93367 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999997558, -9.066821367772111582E-17, -0.6500000000000001332 ) ) ; +#93368 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93369 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93371 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93370 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1458578643762690752 ) ) ; +#93372 = PRESENTATION_STYLE_ASSIGNMENT (( #47454 ) ) ; +#93373 = SURFACE_STYLE_FILL_AREA ( #9574 ) ; +#93374 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#93375 = PLANE ( 'NONE', #65093 ) ; +#93376 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#93377 = FILL_AREA_STYLE_COLOUR ( '', #12011 ) ; +#93378 = SURFACE_STYLE_FILL_AREA ( #70422 ) ; +#93379 = AXIS2_PLACEMENT_3D ( 'NONE', #96702, #19114, #65091 ) ; +#93380 = PRESENTATION_STYLE_ASSIGNMENT (( #30596 ) ) ; +#93381 = SURFACE_STYLE_FILL_AREA ( #74216 ) ; +#93382 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93383 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93385 = PLANE ( 'NONE', #7721 ) ; +#93384 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000222, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#93386 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93387 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -0.9000000000000001332, -0.02000000000000000042 ) ) ; +#93388 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49421 ) ) ; +#93389 = LINE ( 'NONE', #79134, #43575 ) ; +#93390 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93391 = ADVANCED_FACE ( 'NONE', ( #60632 ), #20801, .T. ) ; +#93392 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49430 ), #68905 ) ; +#93393 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34485, 'distance_accuracy_value', 'NONE'); +#93394 = ORIENTED_EDGE ( 'NONE', *, *, #29665, .T. ) ; +#93395 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753240063, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#93396 = PLANE ( 'NONE', #79660 ) ; +#93397 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #2679, #9235, #95558, #62461 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#93398 = PLANE ( 'NONE', #51325 ) ; +#93399 = FILL_AREA_STYLE ('',( #6592 ) ) ; +#93400 = PLANE ( 'NONE', #89501 ) ; +#93401 = PRESENTATION_STYLE_ASSIGNMENT (( #60814 ) ) ; +#93402 = AXIS2_PLACEMENT_3D ( 'NONE', #59565, #37042, #52369 ) ; +#93403 = LINE ( 'NONE', #61820, #48310 ) ; +#93404 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#93405 = CARTESIAN_POINT ( 'NONE', ( 4.670776000000000039, 8.852159000000000333, 0.8648700000000000276 ) ) ; +#93406 = VECTOR ( 'NONE', #23653, 1000.000000000000000 ) ; +#93407 = ADVANCED_FACE ( 'NONE', ( #12568 ), #38146, .T. ) ; +#93408 = ORIENTED_EDGE ( 'NONE', *, *, #96109, .F. ) ; +#93409 = SURFACE_SIDE_STYLE ('',( #14785 ) ) ; +#93410 = VECTOR ( 'NONE', #51736, 1000.000000000000114 ) ; +#93411 = EDGE_LOOP ( 'NONE', ( #39368, #98947, #5643, #4076 ) ) ; +#93412 = FILL_AREA_STYLE ('',( #62330 ) ) ; +#93413 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93414 = SURFACE_STYLE_USAGE ( .BOTH. , #85783 ) ; +#93415 = CARTESIAN_POINT ( 'NONE', ( -0.1289016636980840069, -1.445107798742939931, 0.8299999999999995159 ) ) ; +#93416 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93417 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93418 = PLANE ( 'NONE', #90917 ) ; +#93419 = VECTOR ( 'NONE', #49636, 1000.000000000000000 ) ; +#93420 = ORIENTED_EDGE ( 'NONE', *, *, #23995, .T. ) ; +#93421 = AXIS2_PLACEMENT_3D ( 'NONE', #17593, #73759, #3802 ) ; +#93422 = LINE ( 'NONE', #54162, #17489 ) ; +#93423 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93424 = ORIENTED_EDGE ( 'NONE', *, *, #63512, .F. ) ; +#93425 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #56325 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6266, #53309, #30285 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93426 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28248 ), #44537 ) ; +#93427 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#93428 = ORIENTED_EDGE ( 'NONE', *, *, #41570, .F. ) ; +#93429 = FILL_AREA_STYLE_COLOUR ( '', #39157 ) ; +#93430 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75471 ) ) ; +#93431 = VECTOR ( 'NONE', #55064, 1000.000000000000000 ) ; +#93432 = PLANE ( 'NONE', #43050 ) ; +#93433 = AXIS2_PLACEMENT_3D ( 'NONE', #48297, #55455, #17601 ) ; +#93434 = LINE ( 'NONE', #31188, #65838 ) ; +#93435 = EDGE_CURVE ( 'NONE', #66967, #26858, #53467, .T. ) ; +#93436 = DIRECTION ( 'NONE', ( 6.123031769111889989E-17, 1.000000000000000000, 0.000000000000000000 ) ) ; +#93437 = LINE ( 'NONE', #69459, #14848 ) ; +#93438 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93439 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#93441 = EDGE_LOOP ( 'NONE', ( #32677, #45829, #82765, #62742 ) ) ; +#93440 = VERTEX_POINT ( 'NONE', #9429 ) ; +#93442 = STYLED_ITEM ( 'NONE', ( #32624 ), #59717 ) ; +#93443 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15154 ), #3830 ) ; +#93444 = SURFACE_STYLE_USAGE ( .BOTH. , #62361 ) ; +#93445 = ORIENTED_EDGE ( 'NONE', *, *, #72565, .F. ) ; +#93446 = SURFACE_STYLE_FILL_AREA ( #85821 ) ; +#93447 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33146 ), #83730 ) ; +#93448 = FILL_AREA_STYLE_COLOUR ( '', #58952 ) ; +#93449 = VERTEX_POINT ( 'NONE', #832 ) ; +#93450 = ADVANCED_FACE ( 'NONE', ( #31986 ), #70268, .T. ) ; +#93451 = EDGE_LOOP ( 'NONE', ( #19218, #35164, #83580, #93659 ) ) ; +#93452 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#93453 = SURFACE_SIDE_STYLE ('',( #22534 ) ) ; +#93454 = SURFACE_SIDE_STYLE ('',( #1067 ) ) ; +#93455 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 8.800000000000000711, 0.000000000000000000 ) ) ; +#93457 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93456 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#93458 = ORIENTED_EDGE ( 'NONE', *, *, #53211, .F. ) ; +#93459 = EDGE_LOOP ( 'NONE', ( #699, #50436, #47209, #70366 ) ) ; +#93460 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#93461 = ORIENTED_EDGE ( 'NONE', *, *, #92418, .F. ) ; +#93462 = VECTOR ( 'NONE', #36898, 1000.000000000000000 ) ; +#93464 = ORIENTED_EDGE ( 'NONE', *, *, #49292, .T. ) ; +#93463 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93465 = FACE_OUTER_BOUND ( 'NONE', #93647, .T. ) ; +#93466 = DIRECTION ( 'NONE', ( 0.7071067811865470176, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#93467 = VERTEX_POINT ( 'NONE', #63151 ) ; +#93468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93469 = PLANE ( 'NONE', #68836 ) ; +#93470 = ORIENTED_EDGE ( 'NONE', *, *, #42505, .T. ) ; +#93471 = EDGE_CURVE ( 'NONE', #67856, #1845, #39639, .T. ) ; +#93472 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207790140, -0.9701298701298698424, 0.8100000000000000533 ) ) ; +#93473 = VECTOR ( 'NONE', #38532, 1000.000000000000114 ) ; +#93474 = CARTESIAN_POINT ( 'NONE', ( -2.676179938779915002, -3.100000000000000089, -0.02000000000000000042 ) ) ; +#93476 = EDGE_CURVE ( 'NONE', #82922, #11187, #16624, .T. ) ; +#93475 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36472 ), #83763 ) ; +#93477 = AXIS2_PLACEMENT_3D ( 'NONE', #11255, #80821, #68463 ) ; +#93479 = ORIENTED_EDGE ( 'NONE', *, *, #2615, .F. ) ; +#93478 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#93480 = PRESENTATION_STYLE_ASSIGNMENT (( #52716 ) ) ; +#93481 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#93483 = CARTESIAN_POINT ( 'NONE', ( 1.612727879620370119, -1.495500525511030077, 0.8100000000000000533 ) ) ; +#93482 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8648700000000000276 ) ) ; +#93484 = PRESENTATION_STYLE_ASSIGNMENT (( #31233 ) ) ; +#93485 = SURFACE_STYLE_FILL_AREA ( #85346 ) ; +#93486 = CARTESIAN_POINT ( 'NONE', ( 1.788063499344580087, -1.247965265924660061, 0.8099999999999996092 ) ) ; +#93487 = ORIENTED_EDGE ( 'NONE', *, *, #64221, .F. ) ; +#93488 = FILL_AREA_STYLE ('',( #48084 ) ) ; +#93489 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.499999999999960032, -0.02000000000000000042 ) ) ; +#93490 = CIRCLE ( 'NONE', #10269, 0.009999999999999998473 ) ; +#93491 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#93493 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93492 = CARTESIAN_POINT ( 'NONE', ( -0.8999999999999990230, 3.499999999999989786, 0.1829999999999999960 ) ) ; +#93494 = EDGE_CURVE ( 'NONE', #80455, #8528, #77425, .T. ) ; +#93495 = EDGE_CURVE ( 'NONE', #12514, #7367, #69754, .T. ) ; +#93496 = AXIS2_PLACEMENT_3D ( 'NONE', #61552, #54897, #30342 ) ; +#93497 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52591 ), #49541 ) ; +#93498 = STYLED_ITEM ( 'NONE', ( #26394 ), #35250 ) ; +#93499 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93500 = LINE ( 'NONE', #39925, #47491 ) ; +#93501 = EDGE_LOOP ( 'NONE', ( #42427, #68098, #39084, #89346 ) ) ; +#93502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93504 = AXIS2_PLACEMENT_3D ( 'NONE', #82200, #11130, #82683 ) ; +#93503 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93505 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #69072 ), #41387 ) ; +#93506 = ORIENTED_EDGE ( 'NONE', *, *, #98495, .T. ) ; +#93507 = FILL_AREA_STYLE ('',( #76707 ) ) ; +#93508 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36506 ) ) ; +#93509 = EDGE_CURVE ( 'NONE', #48586, #63162, #15618, .T. ) ; +#93510 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20077 ) ) ; +#93511 = SURFACE_STYLE_FILL_AREA ( #46566 ) ; +#93512 = EDGE_LOOP ( 'NONE', ( #64720, #24968, #18118, #74945 ) ) ; +#93513 = CARTESIAN_POINT ( 'NONE', ( 1.847806625102409894, -0.9622763341455700115, 0.8100000000000008304 ) ) ; +#93514 = CARTESIAN_POINT ( 'NONE', ( 10.50000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#93515 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -0.01500000000000000985, -0.2400000000000000189 ) ) ; +#93516 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93517 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93518 = PRESENTATION_STYLE_ASSIGNMENT (( #31265 ) ) ; +#93519 = PLANE ( 'NONE', #15507 ) ; +#93520 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #95206 ) ) ; +#93521 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.100000000000000311, -0.02000000000001884992 ) ) ; +#93522 = FACE_OUTER_BOUND ( 'NONE', #49200, .T. ) ; +#93523 = LINE ( 'NONE', #23624, #25212 ) ; +#93524 = FACE_OUTER_BOUND ( 'NONE', #53965, .T. ) ; +#93525 = EDGE_CURVE ( 'NONE', #63256, #25261, #78440, .T. ) ; +#93526 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#93527 = VERTEX_POINT ( 'NONE', #48341 ) ; +#93528 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 9.923448000000000491, 0.8991599999999999593 ) ) ; +#93529 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39792 ) ) ; +#93530 = VERTEX_POINT ( 'NONE', #55996 ) ; +#93531 = CARTESIAN_POINT ( 'NONE', ( 11.67113300000000109, 5.245913999999999966, 0.8648700000000000276 ) ) ; +#93532 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93533 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93534 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93535 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93536 = FACE_OUTER_BOUND ( 'NONE', #52879, .T. ) ; +#93537 = ORIENTED_EDGE ( 'NONE', *, *, #37162, .F. ) ; +#93538 = FACE_OUTER_BOUND ( 'NONE', #92339, .T. ) ; +#93539 = SURFACE_STYLE_USAGE ( .BOTH. , #46603 ) ; +#93540 = ORIENTED_EDGE ( 'NONE', *, *, #42635, .F. ) ; +#93541 = CARTESIAN_POINT ( 'NONE', ( 1.271105470580451646, -1.242263041859240857, 0.8099999999998374056 ) ) ; +#93542 = ADVANCED_FACE ( 'NONE', ( #8912 ), #100782, .T. ) ; +#93543 = ORIENTED_EDGE ( 'NONE', *, *, #42533, .T. ) ; +#93544 = LINE ( 'NONE', #45564, #41309 ) ; +#93545 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #18162 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15186, #77020, #16714 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93546 = SURFACE_STYLE_USAGE ( .BOTH. , #60965 ) ; +#93547 = EDGE_CURVE ( 'NONE', #81719, #52187, #71803, .T. ) ; +#93548 = SURFACE_SIDE_STYLE ('',( #48669 ) ) ; +#93549 = ORIENTED_EDGE ( 'NONE', *, *, #35353, .F. ) ; +#93550 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93551 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82194 ), #72387 ) ; +#93552 = CARTESIAN_POINT ( 'NONE', ( 0.4538094727981990539, -1.016713352587220065, 0.8300000000000002931 ) ) ; +#93553 = ADVANCED_FACE ( 'NONE', ( #54987 ), #22820, .T. ) ; +#93554 = VERTEX_POINT ( 'NONE', #56515 ) ; +#93555 = STYLED_ITEM ( 'NONE', ( #37129 ), #38190 ) ; +#93556 = CARTESIAN_POINT ( 'NONE', ( 7.064731000000000094, 10.37243899999999996, 0.8648700000000000276 ) ) ; +#93557 = VECTOR ( 'NONE', #67294, 1000.000000000000000 ) ; +#93558 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, -3.499999999999980016, -0.02000000000000000042 ) ) ; +#93559 = DIRECTION ( 'NONE', ( 6.141358241030730393E-32, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93560 = VERTEX_POINT ( 'NONE', #87618 ) ; +#93561 = ORIENTED_EDGE ( 'NONE', *, *, #33216, .T. ) ; +#93562 = PLANE ( 'NONE', #41774 ) ; +#93563 = VECTOR ( 'NONE', #16521, 1000.000000000000114 ) ; +#93564 = ORIENTED_EDGE ( 'NONE', *, *, #96523, .T. ) ; +#93565 = VECTOR ( 'NONE', #31, 1000.000000000000000 ) ; +#93566 = AXIS2_PLACEMENT_3D ( 'NONE', #56224, #71013, #15851 ) ; +#93567 = ORIENTED_EDGE ( 'NONE', *, *, #62959, .T. ) ; +#93568 = ORIENTED_EDGE ( 'NONE', *, *, #40656, .F. ) ; +#93569 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47765 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43037, #97624, #4240 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93570 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93571 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.164082792207790096, 0.8100000000000000533 ) ) ; +#93572 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93573 = VECTOR ( 'NONE', #77535, 1000.000000000000000 ) ; +#93574 = ORIENTED_EDGE ( 'NONE', *, *, #6954, .F. ) ; +#93575 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 6.650000000000000355, 0.03429000000000000103 ) ) ; +#93576 = CYLINDRICAL_SURFACE ( 'NONE', #47592, 0.1000000000000000194 ) ; +#93577 = EDGE_LOOP ( 'NONE', ( #20483, #74173, #19326, #40860 ) ) ; +#93578 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93579 = CARTESIAN_POINT ( 'NONE', ( 1.655235389610390184, -1.219480519480520053, 0.8100000000000000533 ) ) ; +#93580 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93581 = CIRCLE ( 'NONE', #21847, 0.01000000000000002623 ) ; +#93582 = VERTEX_POINT ( 'NONE', #64638 ) ; +#93583 = ORIENTED_EDGE ( 'NONE', *, *, #86747, .F. ) ; +#93584 = AXIS2_PLACEMENT_3D ( 'NONE', #82968, #44147, #12431 ) ; +#93585 = EDGE_CURVE ( 'NONE', #80230, #25651, #96258, .T. ) ; +#93586 = ADVANCED_FACE ( 'NONE', ( #80990 ), #95740, .T. ) ; +#93588 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93587 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93589 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#93590 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#93591 = LINE ( 'NONE', #31351, #67900 ) ; +#93592 = EDGE_LOOP ( 'NONE', ( #22960, #63004, #5873, #73672 ) ) ; +#93593 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93594 = VECTOR ( 'NONE', #70487, 1000.000000000000000 ) ; +#93595 = ORIENTED_EDGE ( 'NONE', *, *, #30872, .T. ) ; +#93597 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#93596 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93598 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#93599 = EDGE_CURVE ( 'NONE', #31591, #43280, #49322, .T. ) ; +#93600 = ADVANCED_FACE ( 'NONE', ( #18652 ), #49847, .F. ) ; +#93601 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36612 ) ) ; +#93602 = FACE_OUTER_BOUND ( 'NONE', #9126, .T. ) ; +#93604 = ADVANCED_FACE ( 'NONE', ( #74313 ), #98703, .F. ) ; +#93603 = FILL_AREA_STYLE_COLOUR ( '', #29500 ) ; +#93606 = STYLED_ITEM ( 'NONE', ( #76617 ), #48037 ) ; +#93605 = LINE ( 'NONE', #39531, #93563 ) ; +#93607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61105 ) ) ; +#93608 = SURFACE_SIDE_STYLE ('',( #23223 ) ) ; +#93609 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93610 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93611 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.33511999999999986, 0.8991599999999999593 ) ) ; +#93612 = ORIENTED_EDGE ( 'NONE', *, *, #16638, .T. ) ; +#93613 = CARTESIAN_POINT ( 'NONE', ( -1.293111275392700099, -1.070174563215090080, 0.8300000000000002931 ) ) ; +#93614 = VECTOR ( 'NONE', #53430, 1000.000000000000000 ) ; +#93617 = FILL_AREA_STYLE ('',( #46679 ) ) ; +#93616 = FACE_OUTER_BOUND ( 'NONE', #69254, .T. ) ; +#93615 = SURFACE_STYLE_USAGE ( .BOTH. , #7800 ) ; +#93618 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, 0.000000000000000000 ) ) ; +#93619 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64518, 'distance_accuracy_value', 'NONE'); +#93620 = SURFACE_SIDE_STYLE ('',( #25274 ) ) ; +#93621 = EDGE_CURVE ( 'NONE', #76960, #29713, #29349, .T. ) ; +#93622 = VECTOR ( 'NONE', #71219, 1000.000000000000000 ) ; +#93623 = FACE_OUTER_BOUND ( 'NONE', #48173, .T. ) ; +#93624 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 1.100000000000000311, -0.02000000000000000042 ) ) ; +#93625 = CIRCLE ( 'NONE', #98480, 0.009999999999999998473 ) ; +#93626 = ORIENTED_EDGE ( 'NONE', *, *, #59231, .T. ) ; +#93627 = LINE ( 'NONE', #78860, #89665 ) ; +#93629 = EDGE_CURVE ( 'NONE', #24082, #5182, #82977, .T. ) ; +#93628 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93630 = CARTESIAN_POINT ( 'NONE', ( 1.581818181818180014, -1.091883116883120008, 0.8100000000000000533 ) ) ; +#93632 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #79367 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5079, #83239, #98951 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93631 = VECTOR ( 'NONE', #4824, 1000.000000000000000 ) ; +#93633 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93634 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93635 = LINE ( 'NONE', #31391, #12540 ) ; +#93636 = SURFACE_SIDE_STYLE ('',( #16048 ) ) ; +#93637 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93638 = LINE ( 'NONE', #6815, #52272 ) ; +#93639 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 1.899999999999999911, 0.000000000000000000 ) ) ; +#93640 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93641 = AXIS2_PLACEMENT_3D ( 'NONE', #24060, #93439, #37849 ) ; +#93642 = EDGE_CURVE ( 'NONE', #13814, #10057, #74813, .T. ) ; +#93643 = LINE ( 'NONE', #46181, #81517 ) ; +#93644 = EDGE_CURVE ( 'NONE', #97722, #33631, #13974, .T. ) ; +#93645 = FILL_AREA_STYLE ('',( #7332 ) ) ; +#93646 = LINE ( 'NONE', #39574, #95316 ) ; +#93647 = EDGE_LOOP ( 'NONE', ( #46491, #11662, #12068, #84103 ) ) ; +#93648 = AXIS2_PLACEMENT_3D ( 'NONE', #12550, #76403, #37631 ) ; +#93649 = SURFACE_STYLE_USAGE ( .BOTH. , #17080 ) ; +#93650 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93651 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93652 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#93653 = CARTESIAN_POINT ( 'NONE', ( -1.258104321733710007, -1.118172950060400073, 0.8100000000000000533 ) ) ; +#93654 = ORIENTED_EDGE ( 'NONE', *, *, #86689, .F. ) ; +#93655 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #14781 ) ) ; +#93656 = PRESENTATION_STYLE_ASSIGNMENT (( #47243 ) ) ; +#93657 = SURFACE_STYLE_USAGE ( .BOTH. , #23777 ) ; +#93658 = CARTESIAN_POINT ( 'NONE', ( -0.7522321428571430157, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#93659 = ORIENTED_EDGE ( 'NONE', *, *, #77385, .F. ) ; +#93660 = VECTOR ( 'NONE', #61510, 1000.000000000000000 ) ; +#93661 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000189, -0.1499999999999999667, 0.1900000000000000022 ) ) ; +#93662 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#93663 = EDGE_CURVE ( 'NONE', #91380, #39237, #60522, .T. ) ; +#93664 = CARTESIAN_POINT ( 'NONE', ( 0.6500000000000001332, 3.099999999999980549, 0.000000000000000000 ) ) ; +#93665 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33394 ), #28492 ) ; +#93666 = VERTEX_POINT ( 'NONE', #12941 ) ; +#93667 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#93668 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76280, 'distance_accuracy_value', 'NONE'); +#93669 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87231 ), #56294 ) ; +#93670 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #25256 ) ) ; +#93671 = EDGE_CURVE ( 'NONE', #50012, #36803, #37022, .T. ) ; +#93672 = VERTEX_POINT ( 'NONE', #83483 ) ; +#93673 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#93674 = LINE ( 'NONE', #22781, #18188 ) ; +#93675 = ORIENTED_EDGE ( 'NONE', *, *, #8234, .T. ) ; +#93676 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93677 = CARTESIAN_POINT ( 'NONE', ( -0.05183531411288819918, -1.501723168847330259, 0.8100000000000000533 ) ) ; +#93678 = EDGE_CURVE ( 'NONE', #16845, #70963, #1102, .T. ) ; +#93679 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.185754870129869909, 0.8100000000000000533 ) ) ; +#93680 = STYLED_ITEM ( 'NONE', ( #85156 ), #48321 ) ; +#93681 = AXIS2_PLACEMENT_3D ( 'NONE', #74694, #4719, #22049 ) ; +#93682 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93683 = CYLINDRICAL_SURFACE ( 'NONE', #44859, 0.02999999999999997113 ) ; +#93684 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #20663, #46738 ) ; +#93685 = CARTESIAN_POINT ( 'NONE', ( 0.2416947311349459948, -1.083527867505859943, 0.8299999999999999600 ) ) ; +#93686 = EDGE_CURVE ( 'NONE', #56847, #63097, #59544, .T. ) ; +#93687 = ORIENTED_EDGE ( 'NONE', *, *, #29458, .F. ) ; +#93688 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#93689 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #94244, 'distance_accuracy_value', 'NONE'); +#93690 = CARTESIAN_POINT ( 'NONE', ( -1.792207792207789918, -0.9701298701298699534, 0.8100000000000000533 ) ) ; +#93691 = SURFACE_STYLE_FILL_AREA ( #53943 ) ; +#93692 = PRESENTATION_STYLE_ASSIGNMENT (( #55484 ) ) ; +#93693 = AXIS2_PLACEMENT_3D ( 'NONE', #71480, #86801, #69426 ) ; +#93694 = VECTOR ( 'NONE', #52196, 1000.000000000000000 ) ; +#93695 = EDGE_LOOP ( 'NONE', ( #50492, #89695, #38344, #33610 ) ) ; +#93696 = DIRECTION ( 'NONE', ( -0.7071067806865475314, 0.7071067816865476141, 0.000000000000000000 ) ) ; +#93697 = LINE ( 'NONE', #16110, #130 ) ; +#93699 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #38541 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12072, #97865, #38159 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93698 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36707 ) ) ; +#93700 = AXIS2_PLACEMENT_3D ( 'NONE', #71204, #1785, #86532 ) ; +#93701 = FACE_OUTER_BOUND ( 'NONE', #95752, .T. ) ; +#93702 = ORIENTED_EDGE ( 'NONE', *, *, #66877, .F. ) ; +#93704 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93703 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#93705 = ORIENTED_EDGE ( 'NONE', *, *, #42563, .T. ) ; +#93706 = EDGE_CURVE ( 'NONE', #83615, #33480, #4839, .T. ) ; +#93707 = ORIENTED_EDGE ( 'NONE', *, *, #25686, .F. ) ; +#93708 = EDGE_CURVE ( 'NONE', #48947, #61653, #60024, .T. ) ; +#93709 = CARTESIAN_POINT ( 'NONE', ( 1.347523492357600050, -1.285676881280640282, 0.8299999999999999600 ) ) ; +#93710 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36710 ) ) ; +#93711 = FACE_OUTER_BOUND ( 'NONE', #73133, .T. ) ; +#93712 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#93713 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.05000000000000002359, 0.2100000000000000200 ) ) ; +#93714 = ORIENTED_EDGE ( 'NONE', *, *, #55999, .F. ) ; +#93715 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100433 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11911, #21163, #51327 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93716 = LINE ( 'NONE', #23834, #51577 ) ; +#93717 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93718 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000000113, 0.8991599999999999593 ) ) ; +#93719 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8991599999999999593 ) ) ; +#93720 = ORIENTED_EDGE ( 'NONE', *, *, #72730, .T. ) ; +#93721 = PRESENTATION_STYLE_ASSIGNMENT (( #93224 ) ) ; +#93722 = SURFACE_STYLE_USAGE ( .BOTH. , #45752 ) ; +#93723 = VERTEX_POINT ( 'NONE', #99203 ) ; +#93724 = ORIENTED_EDGE ( 'NONE', *, *, #36375, .F. ) ; +#93726 = CARTESIAN_POINT ( 'NONE', ( 0.9500000000000009548, 3.099999999999980549, 0.000000000000000000 ) ) ; +#93725 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93727 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93728 = EDGE_CURVE ( 'NONE', #40675, #26939, #6296, .T. ) ; +#93729 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93730 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93731 = EDGE_CURVE ( 'NONE', #53420, #89708, #84963, .T. ) ; +#93732 = VECTOR ( 'NONE', #37982, 1000.000000000000114 ) ; +#93733 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#93734 = ADVANCED_FACE ( 'NONE', ( #87005 ), #100179, .T. ) ; +#93735 = VECTOR ( 'NONE', #10671, 1000.000000000000000 ) ; +#93736 = CARTESIAN_POINT ( 'NONE', ( -0.007915629041866760474, -1.066767002799750008, 0.8299999999999999600 ) ) ; +#93737 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93738 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999334, 0.1499999999999999667, -0.01999999999999999695 ) ) ; +#93739 = PLANE ( 'NONE', #13929 ) ; +#93740 = ORIENTED_EDGE ( 'NONE', *, *, #31981, .F. ) ; +#93742 = AXIS2_PLACEMENT_3D ( 'NONE', #40932, #48592, #72 ) ; +#93741 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93743 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #22892 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56913, #726, #100027 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93744 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#93745 = CARTESIAN_POINT ( 'NONE', ( 1.850000000000000311, 3.099999999999969891, 0.000000000000000000 ) ) ; +#93746 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54302 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78271, #40994, #634 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93747 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21278 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3519, #34677, #88775 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93748 = PLANE ( 'NONE', #10797 ) ; +#93749 = PRESENTATION_STYLE_ASSIGNMENT (( #15133 ) ) ; +#93750 = VERTEX_POINT ( 'NONE', #8291 ) ; +#93751 = VECTOR ( 'NONE', #36619, 1000.000000000000000 ) ; +#93753 = EDGE_CURVE ( 'NONE', #22947, #87419, #73526, .T. ) ; +#93752 = CARTESIAN_POINT ( 'NONE', ( 5.363741000000000092, 9.545123000000000246, 0.8991599999999999593 ) ) ; +#93754 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #20614 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74186, #60757, #10278 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93755 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36946 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19233, #83051, #81579 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93756 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93757 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93758 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.000000000000000000, 0.2349999999999999867 ) ) ; +#93759 = SURFACE_STYLE_USAGE ( .BOTH. , #85643 ) ; +#93760 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#93761 = FILL_AREA_STYLE ('',( #71335 ) ) ; +#93762 = STYLED_ITEM ( 'NONE', ( #43887 ), #77552 ) ; +#93763 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1350000000000000089 ) ) ; +#93764 = EDGE_CURVE ( 'NONE', #17922, #64996, #39023, .T. ) ; +#93765 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000466, 0.1499999999999999667, 0.1900000000000000022 ) ) ; +#93766 = FILL_AREA_STYLE ('',( #62696 ) ) ; +#93767 = FILL_AREA_STYLE_COLOUR ( '', #58526 ) ; +#93768 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2997 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #35349, #59845, #4650 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93769 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8972 ), #27012 ) ; +#93770 = FILL_AREA_STYLE_COLOUR ( '', #3625 ) ; +#93771 = EDGE_LOOP ( 'NONE', ( #81397, #83190, #57230, #40771 ) ) ; +#93772 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#93773 = PLANE ( 'NONE', #11059 ) ; +#93774 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93776 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#93775 = STYLED_ITEM ( 'NONE', ( #99444 ), #39021 ) ; +#93777 = VECTOR ( 'NONE', #81302, 1000.000000000000000 ) ; +#93778 = FACE_OUTER_BOUND ( 'NONE', #21989, .T. ) ; +#93779 = LINE ( 'NONE', #47366, #80259 ) ; +#93780 = FILL_AREA_STYLE_COLOUR ( '', #79181 ) ; +#93781 = CARTESIAN_POINT ( 'NONE', ( 1.222840576094515352, -1.157551243805461594, 0.8099999999998908073 ) ) ; +#93782 = AXIS2_PLACEMENT_3D ( 'NONE', #32878, #80867, #3237 ) ; +#93783 = PLANE ( 'NONE', #37964 ) ; +#93784 = LINE ( 'NONE', #6487, #48318 ) ; +#93785 = EDGE_CURVE ( 'NONE', #73618, #34706, #30318, .T. ) ; +#93786 = EDGE_LOOP ( 'NONE', ( #97671, #79649, #52548, #42899 ) ) ; +#93787 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93788 = CARTESIAN_POINT ( 'NONE', ( 1.711221411465380093, -1.219829592979950084, 0.8299999999999994049 ) ) ; +#93789 = PRESENTATION_STYLE_ASSIGNMENT (( #63235 ) ) ; +#93790 = STYLED_ITEM ( 'NONE', ( #88967 ), #12691 ) ; +#93791 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93792 = CARTESIAN_POINT ( 'NONE', ( 0.5500000000000010436, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#93793 = EDGE_CURVE ( 'NONE', #7585, #23563, #13083, .T. ) ; +#93794 = ORIENTED_EDGE ( 'NONE', *, *, #4413, .F. ) ; +#93795 = EDGE_LOOP ( 'NONE', ( #72238, #53066, #13959, #39450 ) ) ; +#93796 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#93797 = ORIENTED_EDGE ( 'NONE', *, *, #18381, .T. ) ; +#93798 = CARTESIAN_POINT ( 'NONE', ( 9.426797000000000537, 10.41506900000000080, 0.8991599999999999593 ) ) ; +#93799 = EDGE_CURVE ( 'NONE', #53559, #41304, #23710, .T. ) ; +#93800 = PRESENTATION_STYLE_ASSIGNMENT (( #69845 ) ) ; +#93801 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.900000000000000355, 0.000000000000000000 ) ) ; +#93802 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93803 = PRODUCT_CONTEXT ( 'NONE', #1185, 'mechanical' ) ; +#93804 = CARTESIAN_POINT ( 'NONE', ( 9.924578999999999596, 8.109697000000000600, 0.8648700000000000276 ) ) ; +#93805 = PLANE ( 'NONE', #14730 ) ; +#93806 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #23760 ) ) ; +#93808 = VERTEX_POINT ( 'NONE', #38514 ) ; +#93807 = ORIENTED_EDGE ( 'NONE', *, *, #82292, .F. ) ; +#93809 = EDGE_CURVE ( 'NONE', #67841, #60513, #71170, .T. ) ; +#93810 = ORIENTED_EDGE ( 'NONE', *, *, #59763, .F. ) ; +#93811 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43353 ) ) ; +#93812 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87669, 'distance_accuracy_value', 'NONE'); +#93813 = PRESENTATION_STYLE_ASSIGNMENT (( #62745 ) ) ; +#93814 = LINE ( 'NONE', #46878, #12981 ) ; +#93815 = VERTEX_POINT ( 'NONE', #78335 ) ; +#93816 = ADVANCED_FACE ( 'NONE', ( #7290 ), #53836, .T. ) ; +#93817 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70988 ), #40021 ) ; +#93818 = PLANE ( 'NONE', #5797 ) ; +#93819 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #80859 ) ) ; +#93820 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1499999999999999944 ) ) ; +#93821 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93822 = ORIENTED_EDGE ( 'NONE', *, *, #8959, .T. ) ; +#93823 = VECTOR ( 'NONE', #10526, 1000.000000000000000 ) ; +#93824 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35965 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99162, #70476, #531 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93826 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93825 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93827 = EDGE_LOOP ( 'NONE', ( #98192, #40267, #51556, #51168 ) ) ; +#93828 = EDGE_CURVE ( 'NONE', #93881, #29809, #97139, .T. ) ; +#93829 = ORIENTED_EDGE ( 'NONE', *, *, #36621, .F. ) ; +#93830 = SURFACE_STYLE_FILL_AREA ( #70909 ) ; +#93831 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93834 = EDGE_CURVE ( 'NONE', #84398, #12418, #89018, .T. ) ; +#93833 = VERTEX_POINT ( 'NONE', #19041 ) ; +#93832 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93835 = EDGE_CURVE ( 'NONE', #2230, #57020, #79344, .T. ) ; +#93836 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4749999999999999778, -0.2400000000000000189 ) ) ; +#93837 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8991599999999999593 ) ) ; +#93838 = STYLED_ITEM ( 'NONE', ( #2050 ), #15783 ) ; +#93839 = DIRECTION ( 'NONE', ( 1.000000000000000000, 5.551115123125780237E-17, -3.081487911019574628E-33 ) ) ; +#93840 = ORIENTED_EDGE ( 'NONE', *, *, #55281, .F. ) ; +#93841 = FILL_AREA_STYLE_COLOUR ( '', #82658 ) ; +#93842 = ORIENTED_EDGE ( 'NONE', *, *, #53715, .T. ) ; +#93843 = ORIENTED_EDGE ( 'NONE', *, *, #84540, .T. ) ; +#93845 = FILL_AREA_STYLE ('',( #77062 ) ) ; +#93844 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93846 = CARTESIAN_POINT ( 'NONE', ( 5.929425500500174806, 2.417487499499824555, 0.8991599999999999593 ) ) ; +#93847 = EDGE_CURVE ( 'NONE', #26858, #86708, #73205, .T. ) ; +#93848 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93849 = VECTOR ( 'NONE', #68995, 1000.000000000000000 ) ; +#93850 = LINE ( 'NONE', #40309, #6360 ) ; +#93851 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85649, 'distance_accuracy_value', 'NONE'); +#93852 = SURFACE_STYLE_USAGE ( .BOTH. , #86755 ) ; +#93853 = ORIENTED_EDGE ( 'NONE', *, *, #27878, .F. ) ; +#93854 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.000000000000000000 ) ) ; +#93855 = ORIENTED_EDGE ( 'NONE', *, *, #67035, .F. ) ; +#93856 = VECTOR ( 'NONE', #13560, 1000.000000000000000 ) ; +#93857 = LINE ( 'NONE', #22977, #43136 ) ; +#93858 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93860 = LINE ( 'NONE', #70942, #4326 ) ; +#93859 = FILL_AREA_STYLE_COLOUR ( '', #21874 ) ; +#93861 = CARTESIAN_POINT ( 'NONE', ( 1.776971753240009999, -0.9939892240680031632, 0.8100000000000000533 ) ) ; +#93862 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, -9.289444213855800265E-17, -0.8499999999999999778 ) ) ; +#93863 = SURFACE_STYLE_FILL_AREA ( #62804 ) ; +#93864 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93865 = CARTESIAN_POINT ( 'NONE', ( 9.002532999999999674, 10.41506899999999902, 0.8991599999999999593 ) ) ; +#93866 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93867 = FACE_OUTER_BOUND ( 'NONE', #48323, .T. ) ; +#93868 = LINE ( 'NONE', #10071, #39832 ) ; +#93869 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99008, #98029, #75625, #29650 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#93870 = VECTOR ( 'NONE', #93729, 1000.000000000000000 ) ; +#93871 = SURFACE_STYLE_USAGE ( .BOTH. , #77598 ) ; +#93872 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.000000000000000000, -1.149999999999999911 ) ) ; +#93873 = PRESENTATION_STYLE_ASSIGNMENT (( #30117 ) ) ; +#93874 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#93875 = ADVANCED_FACE ( 'NONE', ( #48719 ), #64527, .T. ) ; +#93876 = FILL_AREA_STYLE ('',( #62823 ) ) ; +#93877 = AXIS2_PLACEMENT_3D ( 'NONE', #24908, #48393, #56041 ) ; +#93878 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35315 ) ) ; +#93879 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41770 ), #49947 ) ; +#93880 = EDGE_CURVE ( 'NONE', #7382, #31068, #58409, .T. ) ; +#93881 = VERTEX_POINT ( 'NONE', #57913 ) ; +#93882 = PRESENTATION_STYLE_ASSIGNMENT (( #8071 ) ) ; +#93883 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #82777, #89434, #50164, #19978 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#93884 = AXIS2_PLACEMENT_3D ( 'NONE', #63510, #41032, #48175 ) ; +#93885 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21101, 'distance_accuracy_value', 'NONE'); +#93886 = VERTEX_POINT ( 'NONE', #95628 ) ; +#93888 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52904, 'distance_accuracy_value', 'NONE'); +#93887 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93889 = VECTOR ( 'NONE', #96026, 1000.000000000000000 ) ; +#93890 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#93891 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93892 = VECTOR ( 'NONE', #19149, 1000.000000000000114 ) ; +#93893 = SURFACE_STYLE_FILL_AREA ( #31656 ) ; +#93894 = SURFACE_SIDE_STYLE ('',( #24551 ) ) ; +#93895 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36890 ) ) ; +#93896 = PRESENTATION_STYLE_ASSIGNMENT (( #23514 ) ) ; +#93897 = PRODUCT ( 'Submodel-R0201_part_R0201', 'Submodel-R0201_part_R0201', '', ( #26445 ) ) ; +#93898 = ORIENTED_EDGE ( 'NONE', *, *, #33577, .T. ) ; +#93899 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93900 = EDGE_CURVE ( 'NONE', #45738, #37700, #42555, .T. ) ; +#93901 = VERTEX_POINT ( 'NONE', #72182 ) ; +#93902 = VECTOR ( 'NONE', #90397, 1000.000000000000000 ) ; +#93903 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#93904 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19640, 'distance_accuracy_value', 'NONE'); +#93905 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9497, 'distance_accuracy_value', 'NONE'); +#93906 = FACE_OUTER_BOUND ( 'NONE', #11824, .T. ) ; +#93907 = SURFACE_STYLE_USAGE ( .BOTH. , #53154 ) ; +#93908 = SURFACE_STYLE_USAGE ( .BOTH. , #78145 ) ; +#93909 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93910 = CARTESIAN_POINT ( 'NONE', ( -0.9414213562373100475, 0.01000000000000000021, 0.4500000000000000666 ) ) ; +#93911 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#93912 = SURFACE_STYLE_USAGE ( .BOTH. , #30641 ) ; +#93913 = ORIENTED_EDGE ( 'NONE', *, *, #47434, .F. ) ; +#93914 = LINE ( 'NONE', #30644, #37056 ) ; +#93916 = ADVANCED_FACE ( 'NONE', ( #66030 ), #25734, .T. ) ; +#93915 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, 1.250000000000000000 ) ) ; +#93917 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77641 ) ) ; +#93918 = ORIENTED_EDGE ( 'NONE', *, *, #28090, .F. ) ; +#93919 = PRESENTATION_STYLE_ASSIGNMENT (( #38349 ) ) ; +#93920 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36907 ) ) ; +#93921 = SURFACE_STYLE_USAGE ( .BOTH. , #31683 ) ; +#93922 = VERTEX_POINT ( 'NONE', #20554 ) ; +#93923 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93924 = CARTESIAN_POINT ( 'NONE', ( 1.036559900398249967, -1.306787212278190058, 0.8100000000000000533 ) ) ; +#93925 = FILL_AREA_STYLE ('',( #24 ) ) ; +#93926 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#93927 = LINE ( 'NONE', #54175, #71985 ) ; +#93928 = PLANE ( 'NONE', #93641 ) ; +#93930 = ORIENTED_EDGE ( 'NONE', *, *, #37563, .T. ) ; +#93929 = EDGE_LOOP ( 'NONE', ( #71218, #10121, #93041, #910 ) ) ; +#93931 = AXIS2_PLACEMENT_3D ( 'NONE', #42179, #73319, #26862 ) ; +#93932 = EDGE_CURVE ( 'NONE', #19502, #7500, #11803, .T. ) ; +#93933 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93934 = PLANE ( 'NONE', #57232 ) ; +#93935 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#93936 = VERTEX_POINT ( 'NONE', #76189 ) ; +#93937 = SURFACE_STYLE_USAGE ( .BOTH. , #30665 ) ; +#93939 = PLANE ( 'NONE', #18617 ) ; +#93938 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93940 = VERTEX_POINT ( 'NONE', #20051 ) ; +#93941 = EDGE_CURVE ( 'NONE', #20645, #30427, #45019, .T. ) ; +#93942 = ORIENTED_EDGE ( 'NONE', *, *, #100785, .F. ) ; +#93943 = FACE_OUTER_BOUND ( 'NONE', #66715, .T. ) ; +#93944 = CARTESIAN_POINT ( 'NONE', ( -1.454829545454549899, -1.500000000000000000, 0.8299999999999999600 ) ) ; +#93945 = PLANE ( 'NONE', #71096 ) ; +#93946 = CARTESIAN_POINT ( 'NONE', ( 8.604364000000000345, 11.48243800000000192, 0.8991599999999999593 ) ) ; +#93947 = ORIENTED_EDGE ( 'NONE', *, *, #92005, .F. ) ; +#93949 = ORIENTED_EDGE ( 'NONE', *, *, #29540, .T. ) ; +#93948 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7468 ), #76061 ) ; +#93950 = CARTESIAN_POINT ( 'NONE', ( 11.23272687512504575, 4.807507875125044627, 0.8648700000000000276 ) ) ; +#93951 = VERTEX_POINT ( 'NONE', #6179 ) ; +#93952 = EDGE_CURVE ( 'NONE', #42517, #84102, #83363, .T. ) ; +#93953 = EDGE_CURVE ( 'NONE', #68052, #68209, #31592, .T. ) ; +#93954 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83775 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74202, #57921, #19048 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#93957 = ADVANCED_FACE ( 'NONE', ( #67502 ), #27755, .T. ) ; +#93956 = ORIENTED_EDGE ( 'NONE', *, *, #4713, .T. ) ; +#93955 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#93958 = EDGE_CURVE ( 'NONE', #74502, #1969, #94561, .T. ) ; +#93959 = FILL_AREA_STYLE_COLOUR ( '', #18042 ) ; +#93960 = CARTESIAN_POINT ( 'NONE', ( 1.715954649776489926, -1.507352529807550079, 0.8099999999999996092 ) ) ; +#93961 = ORIENTED_EDGE ( 'NONE', *, *, #96445, .F. ) ; +#93962 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#93963 = VERTEX_POINT ( 'NONE', #51729 ) ; +#93964 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#93965 = LINE ( 'NONE', #85849, #83972 ) ; +#93966 = EDGE_CURVE ( 'NONE', #66478, #97613, #52234, .T. ) ; +#93967 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#93969 = ORIENTED_EDGE ( 'NONE', *, *, #10219, .F. ) ; +#93968 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#93970 = EDGE_CURVE ( 'NONE', #38918, #42116, #58910, .T. ) ; +#93971 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000009645, -0.2400000000000000189 ) ) ; +#93973 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#93972 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#93974 = CARTESIAN_POINT ( 'NONE', ( -1.283361107934890333, -1.099280448394920118, 0.8099999999999148992 ) ) ; +#93975 = VECTOR ( 'NONE', #27014, 1000.000000000000000 ) ; +#93976 = ORIENTED_EDGE ( 'NONE', *, *, #21326, .F. ) ; +#93977 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#93978 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#93979 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 0.6600000000000000311, 0.8000000000000001554 ) ) ; +#93980 = AXIS2_PLACEMENT_3D ( 'NONE', #36474, #76756, #91572 ) ; +#93981 = LINE ( 'NONE', #9192, #65926 ) ; +#93982 = PLANE ( 'NONE', #87706 ) ; +#93983 = FILL_AREA_STYLE ('',( #15392 ) ) ; +#93984 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#93985 = CLOSED_SHELL ( 'NONE', ( #44861, #23452, #41455, #13949, #44240, #3336 ) ) ; +#93986 = LINE ( 'NONE', #78708, #80937 ) ; +#93987 = VECTOR ( 'NONE', #72314, 1000.000000000000000 ) ; +#93988 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#93989 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#93990 = ORIENTED_EDGE ( 'NONE', *, *, #38406, .T. ) ; +#93991 = VECTOR ( 'NONE', #38585, 1000.000000000000000 ) ; +#93992 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#93993 = AXIS2_PLACEMENT_3D ( 'NONE', #30195, #30693, #54211 ) ; +#93994 = ORIENTED_EDGE ( 'NONE', *, *, #14452, .T. ) ; +#93995 = SURFACE_STYLE_USAGE ( .BOTH. , #77206 ) ; +#93997 = SURFACE_STYLE_FILL_AREA ( #55280 ) ; +#93996 = PRESENTATION_STYLE_ASSIGNMENT (( #607 ) ) ; +#93998 = VECTOR ( 'NONE', #95121, 1000.000000000000000 ) ; +#93999 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.250000000000000444, 0.000000000000000000 ) ) ; +#94000 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94001 = FILL_AREA_STYLE ('',( #613 ) ) ; +#94002 = EDGE_CURVE ( 'NONE', #5550, #93672, #31234, .T. ) ; +#94003 = ORIENTED_EDGE ( 'NONE', *, *, #63204, .T. ) ; +#94004 = LINE ( 'NONE', #86915, #22903 ) ; +#94005 = PRESENTATION_STYLE_ASSIGNMENT (( #62946 ) ) ; +#94006 = FILL_AREA_STYLE_COLOUR ( '', #68144 ) ; +#94007 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94008 = SURFACE_SIDE_STYLE ('',( #79258 ) ) ; +#94009 = CARTESIAN_POINT ( 'NONE', ( -0.2400000000000000466, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#94010 = CARTESIAN_POINT ( 'NONE', ( 7.661838000000000370, 2.155857000000000134, 0.8991599999999999593 ) ) ; +#94011 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94012 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 1.399999999999999911, -0.1499999999999999944 ) ) ; +#94013 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#94014 = FACE_OUTER_BOUND ( 'NONE', #3934, .T. ) ; +#94015 = CARTESIAN_POINT ( 'NONE', ( 0.01806955754146100102, -0.9394184040112210088, 0.8100000000000000533 ) ) ; +#94016 = FILL_AREA_STYLE_COLOUR ( '', #13331 ) ; +#94017 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34984, 'distance_accuracy_value', 'NONE'); +#94018 = FACE_OUTER_BOUND ( 'NONE', #9032, .T. ) ; +#94019 = VECTOR ( 'NONE', #91407, 1000.000000000000000 ) ; +#94020 = PLANE ( 'NONE', #78135 ) ; +#94021 = EDGE_LOOP ( 'NONE', ( #100550, #25226, #273, #19412 ) ) ; +#94022 = ORIENTED_EDGE ( 'NONE', *, *, #93629, .F. ) ; +#94023 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94024 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70034, 'distance_accuracy_value', 'NONE'); +#94025 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #29501, 'distance_accuracy_value', 'NONE'); +#94026 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#94027 = LINE ( 'NONE', #95056, #43282 ) ; +#94028 = FACE_OUTER_BOUND ( 'NONE', #60485, .T. ) ; +#94029 = AXIS2_PLACEMENT_3D ( 'NONE', #52387, #37575, #13489 ) ; +#94030 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94031 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94032 = CARTESIAN_POINT ( 'NONE', ( 0.09306199881179780253, -1.350767436372750208, 0.8300000000000004041 ) ) ; +#94033 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8648700000000000276 ) ) ; +#94034 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#94035 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, -0.000000000000000000 ) ) ; +#94036 = VERTEX_POINT ( 'NONE', #77184 ) ; +#94037 = SURFACE_STYLE_FILL_AREA ( #77758 ) ; +#94039 = EDGE_CURVE ( 'NONE', #3859, #61755, #61409, .T. ) ; +#94038 = FILL_AREA_STYLE ('',( #86433 ) ) ; +#94040 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #22825, 'distance_accuracy_value', 'NONE'); +#94041 = ORIENTED_EDGE ( 'NONE', *, *, #74430, .F. ) ; +#94042 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94043 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000010214, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#94044 = AXIS2_PLACEMENT_3D ( 'NONE', #97140, #58912, #18547 ) ; +#94045 = VERTEX_POINT ( 'NONE', #100548 ) ; +#94046 = SURFACE_STYLE_USAGE ( .BOTH. , #62984 ) ; +#94047 = FACE_OUTER_BOUND ( 'NONE', #2792, .T. ) ; +#94048 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#94049 = SURFACE_STYLE_USAGE ( .BOTH. , #15964 ) ; +#94050 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94052 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94051 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61043 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93933, #40385, #45577 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94053 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.05000000000000002359, 0.1900000000000000022 ) ) ; +#94054 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92806 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17432, #79766, #41964 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94055 = ORIENTED_EDGE ( 'NONE', *, *, #68886, .T. ) ; +#94056 = FILL_AREA_STYLE ('',( #57342 ) ) ; +#94058 = CIRCLE ( 'NONE', #50129, 0.05000000000000002359 ) ; +#94057 = FACE_OUTER_BOUND ( 'NONE', #4813, .T. ) ; +#94059 = SURFACE_SIDE_STYLE ('',( #23668 ) ) ; +#94060 = VECTOR ( 'NONE', #31679, 1000.000000000000000 ) ; +#94061 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94062 = CLOSED_SHELL ( 'NONE', ( #38874, #81071, #26556, #83958, #83790, #13915, #21483, #59717, #71252, #43989, #82712, #17143, #86946, #86227, #83843, #35250, #88055, #71340, #10814, #70065, #94179, #32130, #47260, #42478 ) ) ; +#94063 = ADVANCED_FACE ( 'NONE', ( #84840 ), #54226, .F. ) ; +#94064 = ORIENTED_EDGE ( 'NONE', *, *, #83816, .T. ) ; +#94065 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94066 = VECTOR ( 'NONE', #44951, 1000.000000000000000 ) ; +#94067 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#94068 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94069 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94070 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#94071 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94072 = FILL_AREA_STYLE ('',( #39483 ) ) ; +#94073 = ORIENTED_EDGE ( 'NONE', *, *, #63181, .F. ) ; +#94074 = ORIENTED_EDGE ( 'NONE', *, *, #16145, .F. ) ; +#94075 = PRESENTATION_STYLE_ASSIGNMENT (( #8757 ) ) ; +#94076 = VECTOR ( 'NONE', #68457, 1000.000000000000000 ) ; +#94077 = ORIENTED_EDGE ( 'NONE', *, *, #36073, .F. ) ; +#94078 = VECTOR ( 'NONE', #92366, 1000.000000000000000 ) ; +#94079 = PLANE ( 'NONE', #50844 ) ; +#94080 = EDGE_LOOP ( 'NONE', ( #13540, #64504, #93087, #95896 ) ) ; +#94082 = ORIENTED_EDGE ( 'NONE', *, *, #98263, .F. ) ; +#94081 = CARTESIAN_POINT ( 'NONE', ( 4.515212750249974150, 8.696595249750023626, 0.8991599999999999593 ) ) ; +#94083 = EDGE_CURVE ( 'NONE', #59871, #43651, #69509, .T. ) ; +#94084 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#94086 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -2.356961244533699997E-16 ) ) ; +#94085 = FILL_AREA_STYLE ('',( #55366 ) ) ; +#94087 = SURFACE_STYLE_FILL_AREA ( #76788 ) ; +#94088 = ORIENTED_EDGE ( 'NONE', *, *, #50733, .F. ) ; +#94089 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000000, -0.02000000000000000042 ) ) ; +#94090 = CARTESIAN_POINT ( 'NONE', ( 1.823120247820650519, -1.344848644821849959, 0.8099999999999997202 ) ) ; +#94091 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#94092 = ORIENTED_EDGE ( 'NONE', *, *, #54475, .F. ) ; +#94093 = CARTESIAN_POINT ( 'NONE', ( 7.064731000000000094, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#94094 = LINE ( 'NONE', #10279, #5622 ) ; +#94095 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 1.149999999999999911, 0.000000000000000000 ) ) ; +#94096 = FILL_AREA_STYLE ('',( #64011 ) ) ; +#94097 = AXIS2_PLACEMENT_3D ( 'NONE', #27429, #96331, #90712 ) ; +#94098 = VERTEX_POINT ( 'NONE', #84357 ) ; +#94099 = VECTOR ( 'NONE', #51375, 1000.000000000000114 ) ; +#94100 = SURFACE_STYLE_FILL_AREA ( #42428 ) ; +#94101 = VERTEX_POINT ( 'NONE', #53225 ) ; +#94102 = EDGE_CURVE ( 'NONE', #74902, #84919, #6667, .T. ) ; +#94104 = SURFACE_STYLE_FILL_AREA ( #8784 ) ; +#94103 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94105 = SURFACE_STYLE_FILL_AREA ( #78334 ) ; +#94106 = SURFACE_STYLE_USAGE ( .BOTH. , #63033 ) ; +#94107 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999979927, 0.8999999999999994671, -0.02000000000000839995 ) ) ; +#94108 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94109 = AXIS2_PLACEMENT_3D ( 'NONE', #55024, #24902, #72329 ) ; +#94110 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000028644, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#94111 = ORIENTED_EDGE ( 'NONE', *, *, #37840, .F. ) ; +#94113 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#94112 = FILL_AREA_STYLE_COLOUR ( '', #72250 ) ; +#94114 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#94115 = CARTESIAN_POINT ( 'NONE', ( 1.323820061220085220, -3.099999999999970335, -0.02000000000000000042 ) ) ; +#94116 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61219, 'distance_accuracy_value', 'NONE'); +#94117 = CARTESIAN_POINT ( 'NONE', ( -0.9392372690293679938, -1.031612284007709990, 0.8100000000000000533 ) ) ; +#94118 = PRESENTATION_STYLE_ASSIGNMENT (( #31364 ) ) ; +#94119 = FILL_AREA_STYLE ('',( #80373 ) ) ; +#94120 = LINE ( 'NONE', #32391, #50875 ) ; +#94121 = DIRECTION ( 'NONE', ( -0.7071045084557405769, -0.7071090539100497452, 0.000000000000000000 ) ) ; +#94122 = DIRECTION ( 'NONE', ( 0.7071075504167430026, -0.7071060119555152568, 0.000000000000000000 ) ) ; +#94123 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71355 ), #37119 ) ; +#94124 = ORIENTED_EDGE ( 'NONE', *, *, #11636, .F. ) ; +#94125 = CARTESIAN_POINT ( 'NONE', ( -0.9584150915164789675, -1.224577966852969935, 0.8300000000000002931 ) ) ; +#94126 = SURFACE_SIDE_STYLE ('',( #71698 ) ) ; +#94127 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #27467, #82099, #12042, #43264 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94128 = VECTOR ( 'NONE', #70183, 1000.000000000000000 ) ; +#94129 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #53356 ) ) ; +#94132 = SURFACE_STYLE_FILL_AREA ( #1239 ) ; +#94131 = SURFACE_STYLE_FILL_AREA ( #63050 ) ; +#94130 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#94133 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999940137, -2.649999999999999911, 0.000000000000000000 ) ) ; +#94134 = FACE_OUTER_BOUND ( 'NONE', #58484, .T. ) ; +#94135 = SURFACE_STYLE_USAGE ( .BOTH. , #38046 ) ; +#94136 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #82744 ) ) ; +#94137 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100595 ) ) ; +#94138 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#94139 = VECTOR ( 'NONE', #55586, 1000.000000000000000 ) ; +#94140 = FILL_AREA_STYLE_COLOUR ( '', #61664 ) ; +#94141 = SURFACE_SIDE_STYLE ('',( #39551 ) ) ; +#94142 = CLOSED_SHELL ( 'NONE', ( #61284, #89822, #63022, #61573, #25741, #44494, #99966 ) ) ; +#94143 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#94144 = EDGE_CURVE ( 'NONE', #25485, #15467, #61996, .T. ) ; +#94145 = VERTEX_POINT ( 'NONE', #582 ) ; +#94146 = STYLED_ITEM ( 'NONE', ( #2022 ), #40571 ) ; +#94147 = SURFACE_STYLE_USAGE ( .BOTH. , #86529 ) ; +#94148 = CARTESIAN_POINT ( 'NONE', ( -1.383450513385343417, 1.393384075950082179, 0.8299999999999999600 ) ) ; +#94149 = VECTOR ( 'NONE', #56709, 1000.000000000000000 ) ; +#94150 = FILL_AREA_STYLE ('',( #33432 ) ) ; +#94151 = FACE_OUTER_BOUND ( 'NONE', #23647, .T. ) ; +#94152 = SURFACE_STYLE_FILL_AREA ( #749 ) ; +#94153 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#94154 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94155 = SURFACE_STYLE_FILL_AREA ( #31903 ) ; +#94156 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#94157 = PLANE ( 'NONE', #19676 ) ; +#94158 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.500000000000000000, 0.1829999999999999682 ) ) ; +#94159 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94160 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #1263 ) ) ; +#94161 = SURFACE_STYLE_USAGE ( .BOTH. , #8839 ) ; +#94162 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94163 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86027 ) ) ; +#94164 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#94165 = ORIENTED_EDGE ( 'NONE', *, *, #41351, .T. ) ; +#94166 = EDGE_LOOP ( 'NONE', ( #62610, #55698, #61410, #53966 ) ) ; +#94167 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8123, 'distance_accuracy_value', 'NONE'); +#94168 = PRESENTATION_STYLE_ASSIGNMENT (( #16062 ) ) ; +#94169 = LINE ( 'NONE', #54924, #63469 ) ; +#94170 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 3.123820061220065281, -0.02000000000000000042 ) ) ; +#94171 = CARTESIAN_POINT ( 'NONE', ( 1.879999999999999893, 0.1000000000000000056, -11.57000000000000028 ) ) ; +#94172 = FILL_AREA_STYLE ('',( #1278 ) ) ; +#94173 = FILL_AREA_STYLE_COLOUR ( '', #46650 ) ; +#94174 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94175 = CARTESIAN_POINT ( 'NONE', ( -1.293111275392700099, -1.070174563215090080, 0.8100000000000000533 ) ) ; +#94176 = ORIENTED_EDGE ( 'NONE', *, *, #65036, .F. ) ; +#94177 = PRESENTATION_STYLE_ASSIGNMENT (( #7847 ) ) ; +#94179 = ADVANCED_FACE ( 'NONE', ( #92973 ), #23090, .F. ) ; +#94178 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#94180 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9297, 'distance_accuracy_value', 'NONE'); +#94181 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 8.384496800554540917E-18, -0.6500000000000001332 ) ) ; +#94182 = AXIS2_PLACEMENT_3D ( 'NONE', #30160, #14305, #6626 ) ; +#94183 = SURFACE_STYLE_USAGE ( .BOTH. , #16076 ) ; +#94184 = VECTOR ( 'NONE', #49754, 1000.000000000000000 ) ; +#94185 = ORIENTED_EDGE ( 'NONE', *, *, #75223, .T. ) ; +#94186 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94187 = LINE ( 'NONE', #23275, #23951 ) ; +#94188 = FACE_OUTER_BOUND ( 'NONE', #59028, .T. ) ; +#94189 = FILL_AREA_STYLE ('',( #70734 ) ) ; +#94190 = CARTESIAN_POINT ( 'NONE', ( -0.2415584415584419997, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#94191 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, -0.1238200612200849871, -0.02000000000000000042 ) ) ; +#94192 = EDGE_LOOP ( 'NONE', ( #21043, #95093, #23503, #59505 ) ) ; +#94193 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94194 = FILL_AREA_STYLE ('',( #53917 ) ) ; +#94195 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45742, 'distance_accuracy_value', 'NONE'); +#94196 = VECTOR ( 'NONE', #1918, 1000.000000000000000 ) ; +#94197 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40389 ), #97400 ) ; +#94198 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.000000000000000000 ) ) ; +#94199 = FILL_AREA_STYLE_COLOUR ( '', #89371 ) ; +#94200 = ADVANCED_FACE ( 'NONE', ( #25132 ), #41937, .T. ) ; +#94201 = VECTOR ( 'NONE', #16417, 1000.000000000000000 ) ; +#94202 = ORIENTED_EDGE ( 'NONE', *, *, #55825, .F. ) ; +#94203 = LINE ( 'NONE', #91344, #23595 ) ; +#94204 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.1250000000000000000 ) ) ; +#94205 = VERTEX_POINT ( 'NONE', #17905 ) ; +#94206 = VECTOR ( 'NONE', #83373, 1000.000000000000000 ) ; +#94207 = PRESENTATION_STYLE_ASSIGNMENT (( #63627 ) ) ; +#94208 = LINE ( 'NONE', #1831, #56564 ) ; +#94209 = LINE ( 'NONE', #63120, #98891 ) ; +#94210 = FILL_AREA_STYLE_COLOUR ( '', #30220 ) ; +#94211 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #11685, #3558 ) ; +#94212 = SURFACE_STYLE_USAGE ( .BOTH. , #97107 ) ; +#94213 = VECTOR ( 'NONE', #88420, 1000.000000000000000 ) ; +#94214 = AXIS2_PLACEMENT_3D ( 'NONE', #73981, #35204, #29994 ) ; +#94215 = ORIENTED_EDGE ( 'NONE', *, *, #54863, .T. ) ; +#94216 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73049 ), #86072 ) ; +#94217 = AXIS2_PLACEMENT_3D ( 'NONE', #39218, #23936, #55081 ) ; +#94218 = EDGE_CURVE ( 'NONE', #75732, #35508, #43691, .T. ) ; +#94219 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999993427, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#94220 = PLANE ( 'NONE', #18315 ) ; +#94221 = FACE_OUTER_BOUND ( 'NONE', #93459, .T. ) ; +#94222 = CLOSED_SHELL ( 'NONE', ( #9893, #43380, #4902, #79253, #3186, #12513 ) ) ; +#94223 = CARTESIAN_POINT ( 'NONE', ( -0.3725002807689830053, -1.021003931094770056, 0.8299999999999999600 ) ) ; +#94224 = EDGE_LOOP ( 'NONE', ( #5489, #86079, #56995, #91613, #63536 ) ) ; +#94226 = STYLED_ITEM ( 'NONE', ( #91782 ), #40721 ) ; +#94225 = LINE ( 'NONE', #54970, #89091 ) ; +#94227 = LINE ( 'NONE', #47281, #22975 ) ; +#94228 = STYLED_ITEM ( 'NONE', ( #17344 ), #35550 ) ; +#94229 = FILL_AREA_STYLE_COLOUR ( '', #946 ) ; +#94230 = VERTEX_POINT ( 'NONE', #48602 ) ; +#94231 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35622 ) ) ; +#94233 = CYLINDRICAL_SURFACE ( 'NONE', #46917, 0.1000000000000000056 ) ; +#94232 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94234 = ORIENTED_EDGE ( 'NONE', *, *, #90853, .T. ) ; +#94235 = EDGE_LOOP ( 'NONE', ( #100666, #68753, #68071, #32720 ) ) ; +#94236 = EDGE_CURVE ( 'NONE', #48000, #12591, #96517, .T. ) ; +#94237 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94238 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #45323 ) ) ; +#94239 = DIRECTION ( 'NONE', ( 1.000000000000000000, 1.463023860841316052E-78, 1.991364888915569965E-47 ) ) ; +#94240 = VERTEX_POINT ( 'NONE', #79744 ) ; +#94241 = FACE_OUTER_BOUND ( 'NONE', #45045, .T. ) ; +#94242 = LINE ( 'NONE', #47299, #4665 ) ; +#94243 = DIRECTION ( 'NONE', ( -0.9390355371548172458, 0.000000000000000000, -0.3438200982495990821 ) ) ; +#94244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94245 = ORIENTED_EDGE ( 'NONE', *, *, #15410, .T. ) ; +#94246 = PRESENTATION_STYLE_ASSIGNMENT (( #24360 ) ) ; +#94247 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8991599999999999593 ) ) ; +#94248 = ORIENTED_EDGE ( 'NONE', *, *, #82764, .F. ) ; +#94249 = EDGE_LOOP ( 'NONE', ( #64733, #28585, #47117, #62252, #20142, #12062 ) ) ; +#94250 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94251 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94252 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94253 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94254 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94255 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42341 ), #99300 ) ; +#94256 = CARTESIAN_POINT ( 'NONE', ( -0.3666666666666679730, 3.500000000000000000, 0.000000000000000000 ) ) ; +#94257 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#94258 = SURFACE_SIDE_STYLE ('',( #46798 ) ) ; +#94259 = VECTOR ( 'NONE', #88533, 1000.000000000000114 ) ; +#94260 = VERTEX_POINT ( 'NONE', #2125 ) ; +#94261 = EDGE_CURVE ( 'NONE', #71596, #94737, #33267, .T. ) ; +#94262 = PRESENTATION_STYLE_ASSIGNMENT (( #6919 ) ) ; +#94264 = SURFACE_STYLE_FILL_AREA ( #63183 ) ; +#94263 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94265 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#94266 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #50330 ) ) ; +#94267 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.476179938779914824, 0.000000000000000000 ) ) ; +#94268 = CARTESIAN_POINT ( 'NONE', ( 5.978923124874956585, 3.287228875125044247, 0.8648700000000000276 ) ) ; +#94269 = LINE ( 'NONE', #77455, #4486 ) ; +#94270 = CARTESIAN_POINT ( 'NONE', ( 1.985229955347904696, 1.447033398135698201, -11.38767203951255880 ) ) ; +#94271 = EDGE_CURVE ( 'NONE', #20227, #41411, #42444, .T. ) ; +#94273 = ORIENTED_EDGE ( 'NONE', *, *, #5103, .F. ) ; +#94272 = STYLED_ITEM ( 'NONE', ( #897 ), #55514 ) ; +#94274 = FACE_OUTER_BOUND ( 'NONE', #99450, .T. ) ; +#94275 = FACE_OUTER_BOUND ( 'NONE', #45334, .T. ) ; +#94276 = FACE_OUTER_BOUND ( 'NONE', #84215, .T. ) ; +#94277 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54293 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7170, #47575, #85359 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94278 = SURFACE_STYLE_USAGE ( .BOTH. , #95278 ) ; +#94279 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51445, 'distance_accuracy_value', 'NONE'); +#94280 = ADVANCED_FACE ( 'NONE', ( #86881 ), #48081, .T. ) ; +#94281 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#94282 = FACE_OUTER_BOUND ( 'NONE', #63935, .T. ) ; +#94283 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#94284 = LINE ( 'NONE', #24400, #75852 ) ; +#94285 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94286 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, -0.8000000000000000444 ) ) ; +#94287 = SURFACE_STYLE_USAGE ( .BOTH. , #70320 ) ; +#94288 = VECTOR ( 'NONE', #15545, 1000.000000000000000 ) ; +#94289 = ADVANCED_FACE ( 'NONE', ( #12202 ), #34795, .T. ) ; +#94290 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94291 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35681 ), #19314 ) ; +#94292 = VECTOR ( 'NONE', #74380, 1000.000000000000114 ) ; +#94293 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19091 ), #16016 ) ; +#94294 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #33881, 'design' ) ; +#94295 = STYLED_ITEM ( 'NONE', ( #67260 ), #110 ) ; +#94296 = SURFACE_STYLE_FILL_AREA ( #69814 ) ; +#94297 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, 0.4500000000000001221 ) ) ; +#94298 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72055, #11172, #1612, #33253, #79727, #2611, #9673, #18404, #79205, #34280, #96997, #81246 ), + .UNSPECIFIED., .F., .F., + ( 4, 2, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000034972, 0.3750000000000076050, 0.4375000000000085487, 0.5000000000000095479, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94299 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94300 = ORIENTED_EDGE ( 'NONE', *, *, #69872, .F. ) ; +#94301 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94302 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94303 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34558, 'distance_accuracy_value', 'NONE'); +#94305 = FILL_AREA_STYLE ('',( #75611 ) ) ; +#94304 = CARTESIAN_POINT ( 'NONE', ( -0.05957252635663159990, -1.226312279485590073, 0.8300000000000002931 ) ) ; +#94306 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#94307 = CARTESIAN_POINT ( 'NONE', ( 1.296764056904538442, -1.176312577709546003, 0.8099999999998790390 ) ) ; +#94308 = ADVANCED_FACE ( 'NONE', ( #43922 ), #11684, .T. ) ; +#94309 = ADVANCED_FACE ( 'NONE', ( #31120 ), #62790, .T. ) ; +#94310 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -0.1000000000000020040, 0.1829999999999709914 ) ) ; +#94311 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94312 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77746 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #709, #55386, #71683 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94313 = VERTEX_POINT ( 'NONE', #93854 ) ; +#94314 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999993339, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#94315 = AXIS2_PLACEMENT_3D ( 'NONE', #66453, #10215, #51155 ) ; +#94316 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94317 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46665, 'distance_accuracy_value', 'NONE'); +#94319 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65630, 'distance_accuracy_value', 'NONE'); +#94320 = FILL_AREA_STYLE ('',( #80064 ) ) ; +#94321 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.5105124837953329830, -1.000000000000000000 ) ) ; +#94322 = ADVANCED_FACE ( 'NONE', ( #31622 ), #36004, .F. ) ; +#94323 = EDGE_LOOP ( 'NONE', ( #68368, #51154, #73541, #91930 ) ) ; +#94324 = ORIENTED_EDGE ( 'NONE', *, *, #46355, .F. ) ; +#94325 = EDGE_CURVE ( 'NONE', #35538, #69719, #11974, .T. ) ; +#94326 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #49479, #96400, #58666, #96903 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94327 = CARTESIAN_POINT ( 'NONE', ( 1.788364155591040117, -1.009819306370540071, 0.8299999999999999600 ) ) ; +#94328 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94329 = VECTOR ( 'NONE', #32047, 1000.000000000000000 ) ; +#94330 = EDGE_LOOP ( 'NONE', ( #76375, #41749, #37419, #96990 ) ) ; +#94331 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94332 = STYLED_ITEM ( 'NONE', ( #44871 ), #74890 ) ; +#94333 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#94334 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#94335 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7831 ), #32423 ) ; +#94336 = LINE ( 'NONE', #72898, #93198 ) ; +#94337 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#94339 = VERTEX_POINT ( 'NONE', #19697 ) ; +#94338 = ORIENTED_EDGE ( 'NONE', *, *, #30197, .F. ) ; +#94340 = ORIENTED_EDGE ( 'NONE', *, *, #56537, .T. ) ; +#94341 = STYLED_ITEM ( 'NONE', ( #66865 ), #56588 ) ; +#94342 = ORIENTED_EDGE ( 'NONE', *, *, #83046, .F. ) ; +#94343 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94344 = ADVANCED_FACE ( 'NONE', ( #66646 ), #59043, .T. ) ; +#94345 = DIRECTION ( 'NONE', ( -0.7071067806865475314, 0.7071067816865476141, 0.000000000000000000 ) ) ; +#94346 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94347 = VERTEX_POINT ( 'NONE', #10055 ) ; +#94348 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37329 ), #30801 ) ; +#94349 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 2.100000000000000089, 1.048695503451051965E-76 ) ) ; +#94350 = EDGE_CURVE ( 'NONE', #64596, #54622, #9065, .T. ) ; +#94351 = CARTESIAN_POINT ( 'NONE', ( -2.033333333333333659, 3.500000000000000000, 0.000000000000000000 ) ) ; +#94352 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94353 = ORIENTED_EDGE ( 'NONE', *, *, #42494, .T. ) ; +#94354 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79760 ), #43866 ) ; +#94356 = SURFACE_STYLE_FILL_AREA ( #78544 ) ; +#94355 = SURFACE_STYLE_FILL_AREA ( #22936 ) ; +#94357 = ORIENTED_EDGE ( 'NONE', *, *, #51251, .F. ) ; +#94358 = ORIENTED_EDGE ( 'NONE', *, *, #68634, .F. ) ; +#94359 = ORIENTED_EDGE ( 'NONE', *, *, #9440, .F. ) ; +#94360 = LINE ( 'NONE', #71922, #33037 ) ; +#94361 = EDGE_CURVE ( 'NONE', #59108, #80853, #97750, .T. ) ; +#94362 = VECTOR ( 'NONE', #22244, 1000.000000000000000 ) ; +#94363 = FACE_OUTER_BOUND ( 'NONE', #66341, .T. ) ; +#94364 = VECTOR ( 'NONE', #36941, 1000.000000000000000 ) ; +#94365 = FILL_AREA_STYLE_COLOUR ( '', #71693 ) ; +#94366 = AXIS2_PLACEMENT_3D ( 'NONE', #78352, #77831, #9819 ) ; +#94367 = LINE ( 'NONE', #64254, #79874 ) ; +#94369 = VERTEX_POINT ( 'NONE', #70935 ) ; +#94368 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94370 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#94371 = PLANE ( 'NONE', #74377 ) ; +#94372 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#94373 = ORIENTED_EDGE ( 'NONE', *, *, #13707, .F. ) ; +#94374 = DIRECTION ( 'NONE', ( -0.7071090539100497452, 0.7071045084557405769, 0.000000000000000000 ) ) ; +#94375 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #68284 ) ) ; +#94376 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94377 = ORIENTED_EDGE ( 'NONE', *, *, #31999, .F. ) ; +#94378 = ORIENTED_EDGE ( 'NONE', *, *, #69285, .T. ) ; +#94380 = CARTESIAN_POINT ( 'NONE', ( 1.150000000000000133, 0.6892893218813450629, 1.099999999999999867 ) ) ; +#94379 = PLANE ( 'NONE', #9691 ) ; +#94381 = FACE_OUTER_BOUND ( 'NONE', #26918, .T. ) ; +#94382 = FACE_OUTER_BOUND ( 'NONE', #26452, .T. ) ; +#94383 = CARTESIAN_POINT ( 'NONE', ( -0.4248777619592499777, -1.223222257147859926, 0.8100000000000000533 ) ) ; +#94384 = VECTOR ( 'NONE', #99100, 1000.000000000000000 ) ; +#94385 = PLANE ( 'NONE', #57665 ) ; +#94387 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#94386 = AXIS2_PLACEMENT_3D ( 'NONE', #2795, #64575, #80926 ) ; +#94388 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#94389 = ORIENTED_EDGE ( 'NONE', *, *, #66435, .F. ) ; +#94390 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#94391 = EDGE_CURVE ( 'NONE', #81798, #31422, #27370, .T. ) ; +#94392 = CARTESIAN_POINT ( 'NONE', ( -0.9119271331630629529, -1.344945484192040075, 0.8299999999999999600 ) ) ; +#94393 = EDGE_LOOP ( 'NONE', ( #24700, #91226, #8888, #46084, #6165, #28201 ) ) ; +#94394 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#94395 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94396 = SURFACE_STYLE_FILL_AREA ( #23474 ) ; +#94398 = SURFACE_STYLE_USAGE ( .BOTH. , #48988 ) ; +#94397 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94399 = PRESENTATION_STYLE_ASSIGNMENT (( #63319 ) ) ; +#94400 = LINE ( 'NONE', #86249, #8606 ) ; +#94401 = EDGE_CURVE ( 'NONE', #12756, #3141, #11941, .T. ) ; +#94402 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#94403 = FILL_AREA_STYLE_COLOUR ( '', #58645 ) ; +#94404 = PRESENTATION_STYLE_ASSIGNMENT (( #34188 ) ) ; +#94405 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01500000000000000291, 0.000000000000000000 ) ) ; +#94406 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #4695 ), #73244 ) ; +#94407 = FILL_AREA_STYLE ('',( #24528 ) ) ; +#94408 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94409 = EDGE_CURVE ( 'NONE', #100039, #39727, #90131, .T. ) ; +#94410 = AXIS2_PLACEMENT_3D ( 'NONE', #94089, #45600, #63016 ) ; +#94411 = CARTESIAN_POINT ( 'NONE', ( 0.3499999999999999778, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#94412 = CARTESIAN_POINT ( 'NONE', ( 2.276179938779915091, 3.099999999999969891, 0.000000000000000000 ) ) ; +#94413 = PRESENTATION_STYLE_ASSIGNMENT (( #92874 ) ) ; +#94414 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94415 = EDGE_CURVE ( 'NONE', #93323, #10027, #70450, .T. ) ; +#94416 = FILL_AREA_STYLE_COLOUR ( '', #35468 ) ; +#94417 = AXIS2_PLACEMENT_3D ( 'NONE', #15481, #53325, #69615 ) ; +#94418 = STYLED_ITEM ( 'NONE', ( #68453 ), #85020 ) ; +#94419 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71002, 'distance_accuracy_value', 'NONE'); +#94420 = VECTOR ( 'NONE', #78487, 1000.000000000000000 ) ; +#94421 = ORIENTED_EDGE ( 'NONE', *, *, #39231, .T. ) ; +#94422 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#94423 = STYLED_ITEM ( 'NONE', ( #14448 ), #56205 ) ; +#94424 = ORIENTED_EDGE ( 'NONE', *, *, #40233, .F. ) ; +#94425 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#94426 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#94427 = FILL_AREA_STYLE_COLOUR ( '', #97330 ) ; +#94428 = LINE ( 'NONE', #56178, #97551 ) ; +#94429 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, -8.400000000000000355, -13.35000000000000142 ) ) ; +#94430 = VECTOR ( 'NONE', #93118, 1000.000000000000000 ) ; +#94431 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, 0.2750000000000000222, -0.1458578643762690752 ) ) ; +#94432 = SURFACE_STYLE_FILL_AREA ( #100470 ) ; +#94433 = EDGE_CURVE ( 'NONE', #76033, #85774, #16771, .T. ) ; +#94434 = EDGE_CURVE ( 'NONE', #73059, #28089, #76311, .T. ) ; +#94435 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38995 ) ) ; +#94436 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94437 = ORIENTED_EDGE ( 'NONE', *, *, #23106, .F. ) ; +#94438 = ORIENTED_EDGE ( 'NONE', *, *, #64754, .T. ) ; +#94439 = STYLED_ITEM ( 'NONE', ( #52253 ), #1419 ) ; +#94440 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#94441 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86296 ), #12900 ) ; +#94442 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#94443 = SURFACE_STYLE_FILL_AREA ( #15821 ) ; +#94444 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, 1.175494350822289960E-30 ) ) ; +#94445 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 5.450014000000000358, 0.03429000000000000103 ) ) ; +#94446 = VERTEX_POINT ( 'NONE', #60040 ) ; +#94447 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94448 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94449 = EDGE_LOOP ( 'NONE', ( #55734, #38930, #37239, #37159 ) ) ; +#94450 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.699999999999999956, 0.1829999999999919746 ) ) ; +#94451 = EDGE_CURVE ( 'NONE', #43131, #28730, #28364, .T. ) ; +#94452 = LINE ( 'NONE', #32707, #51723 ) ; +#94453 = ORIENTED_EDGE ( 'NONE', *, *, #78129, .F. ) ; +#94454 = AXIS2_PLACEMENT_3D ( 'NONE', #76587, #93383, #69402 ) ; +#94455 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#94456 = EDGE_CURVE ( 'NONE', #52187, #21671, #12453, .T. ) ; +#94457 = CARTESIAN_POINT ( 'NONE', ( 1.078134533378849902, -1.401744930657430110, 0.8100000000000000533 ) ) ; +#94458 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94459 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29184 ), #26068 ) ; +#94460 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999989875, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#94461 = LINE ( 'NONE', #48027, #18518 ) ; +#94462 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94464 = PLANE ( 'NONE', #27858 ) ; +#94465 = CARTESIAN_POINT ( 'NONE', ( -0.6859013404417257931, 1.548823167464410844, 0.8100000000000001643 ) ) ; +#94467 = ORIENTED_EDGE ( 'NONE', *, *, #6297, .T. ) ; +#94466 = EDGE_LOOP ( 'NONE', ( #77013, #75000, #40671, #62976 ) ) ; +#94468 = FACE_OUTER_BOUND ( 'NONE', #15102, .T. ) ; +#94469 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94470 = LINE ( 'NONE', #77658, #93594 ) ; +#94471 = ORIENTED_EDGE ( 'NONE', *, *, #54473, .F. ) ; +#94472 = CARTESIAN_POINT ( 'NONE', ( 0.9685869866146590290, 0.4055590759269659951, 0.8100000000000000533 ) ) ; +#94474 = FILL_AREA_STYLE_COLOUR ( '', #28403 ) ; +#94473 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94475 = EDGE_LOOP ( 'NONE', ( #82234, #3498, #13272, #55202 ) ) ; +#94476 = ORIENTED_EDGE ( 'NONE', *, *, #16314, .T. ) ; +#94478 = FACE_OUTER_BOUND ( 'NONE', #4666, .T. ) ; +#94477 = PLANE ( 'NONE', #41562 ) ; +#94479 = VERTEX_POINT ( 'NONE', #68136 ) ; +#94480 = ORIENTED_EDGE ( 'NONE', *, *, #7889, .F. ) ; +#94481 = FACE_OUTER_BOUND ( 'NONE', #69381, .T. ) ; +#94482 = EDGE_LOOP ( 'NONE', ( #37154, #82581, #56517, #49822 ) ) ; +#94483 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4000000000000000222, 0.2999999999999999889 ) ) ; +#94484 = VECTOR ( 'NONE', #17265, 1000.000000000000000 ) ; +#94485 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94486 = ADVANCED_FACE ( 'NONE', ( #83496 ), #67634, .T. ) ; +#94487 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92852 ), #57014 ) ; +#94489 = ORIENTED_EDGE ( 'NONE', *, *, #61743, .F. ) ; +#94488 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.500000000000000000, 0.03429000000000000103 ) ) ; +#94490 = AXIS2_PLACEMENT_3D ( 'NONE', #54686, #89207, #521 ) ; +#94491 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #7976 ), #16199 ) ; +#94492 = FILL_AREA_STYLE_COLOUR ( '', #68561 ) ; +#94493 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94494 = ORIENTED_EDGE ( 'NONE', *, *, #53384, .F. ) ; +#94495 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45329 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79393, #63076, #55428 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94496 = LINE ( 'NONE', #64388, #90780 ) ; +#94497 = SURFACE_STYLE_FILL_AREA ( #46520 ) ; +#94498 = ORIENTED_EDGE ( 'NONE', *, *, #14546, .F. ) ; +#94499 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57553 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #59994, #44605, #58502 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94500 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94501 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #35881 ) ) ; +#94502 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.8333333333333353687, 0.000000000000000000 ) ) ; +#94503 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#94504 = PLANE ( 'NONE', #1892 ) ; +#94505 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94506 = FILL_AREA_STYLE_COLOUR ( '', #98699 ) ; +#94507 = CARTESIAN_POINT ( 'NONE', ( 1.616346165234739951, -0.9925253384799740397, 0.8299999999999990719 ) ) ; +#94508 = VECTOR ( 'NONE', #49478, 1000.000000000000000 ) ; +#94509 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94510 = EDGE_CURVE ( 'NONE', #16467, #65640, #89846, .T. ) ; +#94511 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73347 ) ) ; +#94512 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#94513 = EDGE_LOOP ( 'NONE', ( #56628, #50349, #63139, #29600 ) ) ; +#94514 = FILL_AREA_STYLE_COLOUR ( '', #84326 ) ; +#94515 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94516 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9693 ) ) ; +#94517 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94518 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.155799999999999272, 0.8648700000000000276 ) ) ; +#94519 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000000000, 0.4750000000000000333, 0.2400000000000000466 ) ) ; +#94521 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94520 = SURFACE_STYLE_FILL_AREA ( #16902 ) ; +#94522 = SURFACE_SIDE_STYLE ('',( #63436 ) ) ; +#94523 = EDGE_CURVE ( 'NONE', #66984, #70008, #21693, .T. ) ; +#94524 = STYLED_ITEM ( 'NONE', ( #56676 ), #51137 ) ; +#94525 = ORIENTED_EDGE ( 'NONE', *, *, #49474, .T. ) ; +#94526 = SURFACE_STYLE_FILL_AREA ( #54778 ) ; +#94527 = ORIENTED_EDGE ( 'NONE', *, *, #80481, .T. ) ; +#94528 = SURFACE_STYLE_USAGE ( .BOTH. , #80264 ) ; +#94529 = LINE ( 'NONE', #31762, #9888 ) ; +#94530 = EDGE_CURVE ( 'NONE', #42889, #56597, #4856, .T. ) ; +#94531 = PRESENTATION_STYLE_ASSIGNMENT (( #63452 ) ) ; +#94532 = CARTESIAN_POINT ( 'NONE', ( 8.300000000000000711, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#94534 = EDGE_CURVE ( 'NONE', #65355, #51854, #28851, .T. ) ; +#94533 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19946, 'distance_accuracy_value', 'NONE'); +#94535 = ORIENTED_EDGE ( 'NONE', *, *, #38386, .T. ) ; +#94536 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94537 = CARTESIAN_POINT ( 'NONE', ( -0.01680389005683929904, -1.106837409965790053, 0.8300000000000005151 ) ) ; +#94538 = SURFACE_SIDE_STYLE ('',( #24145 ) ) ; +#94539 = FILL_AREA_STYLE ('',( #47087 ) ) ; +#94540 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.500000000000000000, 0.1829999999999999960 ) ) ; +#94541 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#94542 = AXIS2_PLACEMENT_3D ( 'NONE', #88437, #18475, #95061 ) ; +#94543 = CARTESIAN_POINT ( 'NONE', ( 0.06997596596441089944, -1.057175192472970204, 0.8100000000000000533 ) ) ; +#94544 = ADVANCED_FACE ( 'NONE', ( #90649 ), #60534, .T. ) ; +#94545 = SURFACE_STYLE_FILL_AREA ( #33309 ) ; +#94546 = ADVANCED_FACE ( 'NONE', ( #86506 ), #23219, .T. ) ; +#94547 = STYLED_ITEM ( 'NONE', ( #76933 ), #86135 ) ; +#94548 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37598 ) ) ; +#94549 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #52257 ), #73464 ) ; +#94550 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.300000000000000044, -0.02000000000000000042 ) ) ; +#94551 = ORIENTED_EDGE ( 'NONE', *, *, #31573, .F. ) ; +#94552 = ORIENTED_EDGE ( 'NONE', *, *, #53797, .T. ) ; +#94553 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94554 = VECTOR ( 'NONE', #30073, 1000.000000000000000 ) ; +#94555 = EDGE_CURVE ( 'NONE', #4894, #37284, #47696, .T. ) ; +#94556 = EDGE_CURVE ( 'NONE', #17853, #8413, #71688, .T. ) ; +#94557 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94558 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94559 = STYLED_ITEM ( 'NONE', ( #8868 ), #85236 ) ; +#94560 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84734 ) ) ; +#94561 = CIRCLE ( 'NONE', #71706, 0.01000000000000002623 ) ; +#94562 = CARTESIAN_POINT ( 'NONE', ( 1.099999999999996758, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#94563 = CARTESIAN_POINT ( 'NONE', ( -0.03276632349404259847, -1.496872818153279994, 0.8300000000000004041 ) ) ; +#94564 = CARTESIAN_POINT ( 'NONE', ( 0.01897074359908140079, -1.165682221622120096, 0.8299999999999999600 ) ) ; +#94565 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#94566 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94567 = SURFACE_STYLE_FILL_AREA ( #63481 ) ; +#94568 = ORIENTED_EDGE ( 'NONE', *, *, #36143, .T. ) ; +#94569 = CARTESIAN_POINT ( 'NONE', ( 1.901147915587950044, -1.336905478629369926, 0.8300000000000011813 ) ) ; +#94570 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94571 = STYLED_ITEM ( 'NONE', ( #93813 ), #6776 ) ; +#94572 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94573 = VERTEX_POINT ( 'NONE', #55394 ) ; +#94574 = EDGE_CURVE ( 'NONE', #55045, #83639, #1028, .T. ) ; +#94575 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #48997 ), #3355 ) ; +#94576 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21193 ) ) ; +#94577 = ORIENTED_EDGE ( 'NONE', *, *, #5612, .T. ) ; +#94578 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94579 = EDGE_CURVE ( 'NONE', #65615, #54703, #31873, .T. ) ; +#94580 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94581 = VECTOR ( 'NONE', #77967, 1000.000000000000114 ) ; +#94582 = SURFACE_STYLE_USAGE ( .BOTH. , #86444 ) ; +#94583 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 9.092575000000000074, 0.8648700000000000276 ) ) ; +#94584 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94585 = ORIENTED_EDGE ( 'NONE', *, *, #24989, .F. ) ; +#94586 = SURFACE_SIDE_STYLE ('',( #86448 ) ) ; +#94587 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94588 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94589 = SURFACE_STYLE_FILL_AREA ( #31311 ) ; +#94590 = ORIENTED_EDGE ( 'NONE', *, *, #60823, .T. ) ; +#94591 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94592 = VECTOR ( 'NONE', #54063, 1000.000000000000000 ) ; +#94593 = LINE ( 'NONE', #8750, #93732 ) ; +#94594 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#94595 = PRESENTATION_STYLE_ASSIGNMENT (( #79822 ) ) ; +#94596 = PLANE ( 'NONE', #14985 ) ; +#94597 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94598 = ORIENTED_EDGE ( 'NONE', *, *, #34697, .F. ) ; +#94600 = ORIENTED_EDGE ( 'NONE', *, *, #80394, .T. ) ; +#94599 = VERTEX_POINT ( 'NONE', #69642 ) ; +#94601 = CARTESIAN_POINT ( 'NONE', ( -0.2800000000000000266, 0.4245906043549200204, 0.000000000000000000 ) ) ; +#94602 = ORIENTED_EDGE ( 'NONE', *, *, #36480, .T. ) ; +#94603 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.500000000000000444, 0.000000000000000000 ) ) ; +#94604 = EDGE_CURVE ( 'NONE', #59650, #64596, #1225, .T. ) ; +#94605 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #8092 ), #16313 ) ; +#94606 = ORIENTED_EDGE ( 'NONE', *, *, #52633, .T. ) ; +#94608 = VERTEX_POINT ( 'NONE', #87018 ) ; +#94607 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94609 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94611 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#94610 = LINE ( 'NONE', #41042, #44411 ) ; +#94612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94613 = SURFACE_STYLE_FILL_AREA ( #40535 ) ; +#94614 = ORIENTED_EDGE ( 'NONE', *, *, #88268, .T. ) ; +#94615 = ADVANCED_FACE ( 'NONE', ( #39037 ), #91432, .F. ) ; +#94616 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.03429000000000000103 ) ) ; +#94617 = SURFACE_STYLE_FILL_AREA ( #48193 ) ; +#94618 = ORIENTED_EDGE ( 'NONE', *, *, #35430, .T. ) ; +#94619 = SURFACE_STYLE_FILL_AREA ( #79330 ) ; +#94620 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94621 = LINE ( 'NONE', #95618, #62708 ) ; +#94622 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, -0.1499999999999999944 ) ) ; +#94623 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #11510 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87628, #87131, #47308 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94624 = ORIENTED_EDGE ( 'NONE', *, *, #19371, .T. ) ; +#94625 = LINE ( 'NONE', #79851, #34192 ) ; +#94626 = ORIENTED_EDGE ( 'NONE', *, *, #46255, .T. ) ; +#94627 = PLANE ( 'NONE', #50942 ) ; +#94628 = AXIS2_PLACEMENT_3D ( 'NONE', #91728, #15094, #46249 ) ; +#94629 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94630 = VECTOR ( 'NONE', #66314, 1000.000000000000000 ) ; +#94631 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94632 = DIRECTION ( 'NONE', ( -7.228014483236695569E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94633 = AXIS2_PLACEMENT_3D ( 'NONE', #93719, #24871, #25369 ) ; +#94634 = SURFACE_STYLE_FILL_AREA ( #79858 ) ; +#94635 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94636 = ORIENTED_EDGE ( 'NONE', *, *, #19732, .F. ) ; +#94637 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94638 = PRESENTATION_STYLE_ASSIGNMENT (( #16021 ) ) ; +#94639 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94640 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#94641 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94642 = CARTESIAN_POINT ( 'NONE', ( -0.9392372690293679938, -1.031612284007709990, 0.8299999999999999600 ) ) ; +#94643 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21605 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #100706, #92637, #86018 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94644 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94645 = PRESENTATION_STYLE_ASSIGNMENT (( #48731 ) ) ; +#94646 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94647 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94648 = FILL_AREA_STYLE_COLOUR ( '', #48345 ) ; +#94649 = ORIENTED_EDGE ( 'NONE', *, *, #14444, .F. ) ; +#94650 = CARTESIAN_POINT ( 'NONE', ( -1.204575085674180146, -1.140452398731560013, 0.8300000000000002931 ) ) ; +#94651 = VECTOR ( 'NONE', #75834, 1000.000000000000000 ) ; +#94653 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 2.299999999999999822, 2.243222336733894049E-79 ) ) ; +#94652 = CARTESIAN_POINT ( 'NONE', ( 12.84593600000000002, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#94654 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94655 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #14348, 'distance_accuracy_value', 'NONE'); +#94656 = VECTOR ( 'NONE', #94731, 1000.000000000000114 ) ; +#94657 = FILL_AREA_STYLE_COLOUR ( '', #24124 ) ; +#94658 = FILL_AREA_STYLE_COLOUR ( '', #88658 ) ; +#94659 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999990230, 3.099999999999980549, 0.000000000000000000 ) ) ; +#94660 = CARTESIAN_POINT ( 'NONE', ( 1.750000000000000222, 3.099999999999969891, 0.000000000000000000 ) ) ; +#94661 = ORIENTED_EDGE ( 'NONE', *, *, #99752, .F. ) ; +#94662 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94663 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8648700000000000276 ) ) ; +#94664 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#94665 = PLANE ( 'NONE', #59401 ) ; +#94666 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 8.979438000000001807, 0.8991599999999999593 ) ) ; +#94667 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31142 ), #57264 ) ; +#94668 = CARTESIAN_POINT ( 'NONE', ( 11.23272700000000057, 7.720787999999998874, 0.8648700000000000276 ) ) ; +#94669 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94670 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94671 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94672 = DIRECTION ( 'NONE', ( 1.084202172485500095E-15, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94673 = ORIENTED_EDGE ( 'NONE', *, *, #10805, .T. ) ; +#94674 = SURFACE_SIDE_STYLE ('',( #57437 ) ) ; +#94675 = ORIENTED_EDGE ( 'NONE', *, *, #70191, .T. ) ; +#94677 = ADVANCED_FACE ( 'NONE', ( #34424 ), #49223, .F. ) ; +#94676 = FILL_AREA_STYLE_COLOUR ( '', #88150 ) ; +#94678 = CARTESIAN_POINT ( 'NONE', ( 1.162161998062432700, 1.364349903361321781, 0.8100000000000001643 ) ) ; +#94679 = CARTESIAN_POINT ( 'NONE', ( 0.1542778230595640010, -1.450978309596749893, 0.8100000000000000533 ) ) ; +#94680 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94681 = CARTESIAN_POINT ( 'NONE', ( 0.5096387987012981347, 0.6899999999999999467, -5.759824041329242306E-17 ) ) ; +#94682 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94683 = ORIENTED_EDGE ( 'NONE', *, *, #45766, .F. ) ; +#94684 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94685 = AXIS2_PLACEMENT_3D ( 'NONE', #56007, #48354, #9436 ) ; +#94686 = PRESENTATION_STYLE_ASSIGNMENT (( #80422 ) ) ; +#94687 = ORIENTED_EDGE ( 'NONE', *, *, #72828, .F. ) ; +#94688 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94689 = CARTESIAN_POINT ( 'NONE', ( 12.54593599999999931, 7.292200000000000237, 0.8991599999999999593 ) ) ; +#94690 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22943 ) ) ; +#94691 = EDGE_CURVE ( 'NONE', #15485, #75030, #66040, .T. ) ; +#94692 = FILL_AREA_STYLE_COLOUR ( '', #25022 ) ; +#94693 = AXIS2_PLACEMENT_3D ( 'NONE', #7825, #69673, #31394 ) ; +#94694 = PRESENTATION_STYLE_ASSIGNMENT (( #81458 ) ) ; +#94695 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94696 = CARTESIAN_POINT ( 'NONE', ( -1.529289321881349473, 1.970710678118649861, -0.02000000000000000042 ) ) ; +#94697 = ORIENTED_EDGE ( 'NONE', *, *, #51614, .T. ) ; +#94698 = SURFACE_STYLE_FILL_AREA ( #16584 ) ; +#94699 = VECTOR ( 'NONE', #87369, 1000.000000000000000 ) ; +#94701 = FILL_AREA_STYLE_COLOUR ( '', #19584 ) ; +#94700 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13396, 'distance_accuracy_value', 'NONE'); +#94703 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9809 ) ) ; +#94704 = SURFACE_STYLE_USAGE ( .BOTH. , #87582 ) ; +#94705 = STYLED_ITEM ( 'NONE', ( #37997 ), #7467 ) ; +#94706 = VERTEX_POINT ( 'NONE', #19572 ) ; +#94707 = PRESENTATION_STYLE_ASSIGNMENT (( #71248 ) ) ; +#94708 = LINE ( 'NONE', #42637, #41341 ) ; +#94709 = EDGE_LOOP ( 'NONE', ( #14416, #9540, #58391, #45753, #67171, #96333 ) ) ; +#94710 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94711 = LINE ( 'NONE', #40130, #63438 ) ; +#94712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94713 = SURFACE_SIDE_STYLE ('',( #9401 ) ) ; +#94714 = ITEM_DEFINED_TRANSFORMATION ( 'NONE', 'NONE', #77733, #4347 ) ; +#94715 = EDGE_CURVE ( 'NONE', #70921, #40707, #40110, .T. ) ; +#94716 = VECTOR ( 'NONE', #19063, 1000.000000000000114 ) ; +#94717 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81735 ) ) ; +#94718 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72685, #65030, #80872, #10813 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #24614 ), #52352 ) ; +#94720 = ORIENTED_EDGE ( 'NONE', *, *, #991, .T. ) ; +#94722 = VERTEX_POINT ( 'NONE', #9816 ) ; +#94721 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94723 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #24326, 'distance_accuracy_value', 'NONE'); +#94724 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105604999999999727, 0.8991599999999999593 ) ) ; +#94726 = LINE ( 'NONE', #24845, #82343 ) ; +#94725 = FACE_OUTER_BOUND ( 'NONE', #17949, .T. ) ; +#94727 = ADVANCED_FACE ( 'NONE', ( #64534 ), #95638, .T. ) ; +#94728 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94729 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94730 = VERTEX_POINT ( 'NONE', #60422 ) ; +#94731 = DIRECTION ( 'NONE', ( 0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#94732 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94733 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #57316 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49366, #11470, #10445 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94734 = ORIENTED_EDGE ( 'NONE', *, *, #13709, .F. ) ; +#94736 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#94735 = FILL_AREA_STYLE ('',( #70257 ) ) ; +#94737 = VERTEX_POINT ( 'NONE', #58923 ) ; +#94738 = VECTOR ( 'NONE', #100389, 1000.000000000000000 ) ; +#94739 = ORIENTED_EDGE ( 'NONE', *, *, #45085, .F. ) ; +#94740 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94741 = FACE_OUTER_BOUND ( 'NONE', #98798, .T. ) ; +#94742 = PRESENTATION_STYLE_ASSIGNMENT (( #78439 ) ) ; +#94744 = ORIENTED_EDGE ( 'NONE', *, *, #8854, .T. ) ; +#94743 = STYLED_ITEM ( 'NONE', ( #57986 ), #45526 ) ; +#94745 = FACE_OUTER_BOUND ( 'NONE', #10237, .T. ) ; +#94746 = SURFACE_STYLE_USAGE ( .BOTH. , #63660 ) ; +#94747 = EDGE_LOOP ( 'NONE', ( #49759, #73416, #47032, #39265 ) ) ; +#94748 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, -3.500000000000000444, 0.000000000000000000 ) ) ; +#94749 = ORIENTED_EDGE ( 'NONE', *, *, #62564, .F. ) ; +#94750 = VERTEX_POINT ( 'NONE', #59428 ) ; +#94751 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#94752 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#94753 = ADVANCED_FACE ( 'NONE', ( #52736 ), #91892, .T. ) ; +#94754 = CARTESIAN_POINT ( 'NONE', ( -1.158847402597400045, -0.9545454545454551409, 0.8100000000000086020 ) ) ; +#94755 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23006 ), #6594 ) ; +#94756 = VECTOR ( 'NONE', #29187, 1000.000000000000114 ) ; +#94758 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94757 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94759 = FACE_OUTER_BOUND ( 'NONE', #26482, .T. ) ; +#94761 = EDGE_CURVE ( 'NONE', #13557, #61665, #36908, .T. ) ; +#94760 = CARTESIAN_POINT ( 'NONE', ( -0.06821911881269179800, -1.154690592117219916, 0.8100000000000000533 ) ) ; +#94762 = PRODUCT ( 'Submodel-C0402_part_C0402', 'Submodel-C0402_part_C0402', '', ( #8496 ) ) ; +#94763 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94764 = AXIS2_PLACEMENT_3D ( 'NONE', #22567, #22058, #53223 ) ; +#94765 = PRESENTATION_STYLE_ASSIGNMENT (( #40688 ) ) ; +#94766 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86702 ), #6665 ) ; +#94767 = VERTEX_POINT ( 'NONE', #92017 ) ; +#94768 = CARTESIAN_POINT ( 'NONE', ( 10.94988375024997573, 8.003630750249975279, 0.8648700000000000276 ) ) ; +#94769 = PRESENTATION_STYLE_ASSIGNMENT (( #71315 ) ) ; +#94770 = CIRCLE ( 'NONE', #55688, 0.1000000000000000194 ) ; +#94771 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94772 = AXIS2_PLACEMENT_3D ( 'NONE', #24885, #71825, #32009 ) ; +#94773 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#94774 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.149999999999999911, -0.02000000000000000042 ) ) ; +#94775 = PRESENTATION_STYLE_ASSIGNMENT (( #63683 ) ) ; +#94776 = FILL_AREA_STYLE ('',( #72844 ) ) ; +#94777 = ADVANCED_FACE ( 'NONE', ( #53239 ), #43545, .F. ) ; +#94778 = ORIENTED_EDGE ( 'NONE', *, *, #4583, .T. ) ; +#94779 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23101 ), #45853 ) ; +#94780 = EDGE_CURVE ( 'NONE', #74398, #35238, #46019, .T. ) ; +#94782 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #85959, 'distance_accuracy_value', 'NONE'); +#94781 = CARTESIAN_POINT ( 'NONE', ( 10.36298500000000011, 4.857005000000000017, 0.8648700000000000276 ) ) ; +#94783 = PLANE ( 'NONE', #61977 ) ; +#94784 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62095, #86048, #94688 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94785 = FILL_AREA_STYLE_COLOUR ( '', #100126 ) ; +#94786 = PRESENTATION_STYLE_ASSIGNMENT (( #8957 ) ) ; +#94787 = SURFACE_STYLE_USAGE ( .BOTH. , #39683 ) ; +#94788 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#94789 = LINE ( 'NONE', #40719, #41007 ) ; +#94790 = SURFACE_SIDE_STYLE ('',( #47347 ) ) ; +#94791 = PLANE ( 'NONE', #54990 ) ; +#94792 = SURFACE_STYLE_USAGE ( .BOTH. , #63708 ) ; +#94793 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43882 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6859, #95710, #19125 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94794 = SURFACE_SIDE_STYLE ('',( #24916 ) ) ; +#94795 = SURFACE_SIDE_STYLE ('',( #69807 ) ) ; +#94796 = VECTOR ( 'NONE', #55373, 1000.000000000000000 ) ; +#94797 = EDGE_CURVE ( 'NONE', #92605, #73676, #93500, .T. ) ; +#94798 = FILL_AREA_STYLE ('',( #39186 ) ) ; +#94799 = VECTOR ( 'NONE', #38579, 1000.000000000000000 ) ; +#94800 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000197, 0.8991599999999999593 ) ) ; +#94801 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94802 = EDGE_LOOP ( 'NONE', ( #77046, #50199, #79482, #85382 ) ) ; +#94803 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94804 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#94805 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#94806 = STYLED_ITEM ( 'NONE', ( #16551 ), #51939 ) ; +#94808 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94807 = CARTESIAN_POINT ( 'NONE', ( -0.07142958428783030556, -1.223383224893549892, 0.8300000000000002931 ) ) ; +#94809 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.1499999999999999944, 0.000000000000000000 ) ) ; +#94810 = DIRECTION ( 'NONE', ( 1.000000000000000000, 4.985173066523913740E-65, 8.980489425909800160E-49 ) ) ; +#94811 = EDGE_CURVE ( 'NONE', #82698, #84785, #37573, .T. ) ; +#94812 = SURFACE_STYLE_USAGE ( .BOTH. , #63227 ) ; +#94813 = CYLINDRICAL_SURFACE ( 'NONE', #12412, 0.009999999999999998473 ) ; +#94814 = VERTEX_POINT ( 'NONE', #24644 ) ; +#94815 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999960032, -1.100000000000000089, -0.02000000000003770290 ) ) ; +#94816 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94817 = CARTESIAN_POINT ( 'NONE', ( 1.736362623504380087, -1.223383224893549892, 0.8299999999999994049 ) ) ; +#94818 = VERTEX_POINT ( 'NONE', #32271 ) ; +#94819 = EDGE_LOOP ( 'NONE', ( #32947, #8843, #72530, #25726 ) ) ; +#94820 = LINE ( 'NONE', #8489, #29153 ) ; +#94821 = ORIENTED_EDGE ( 'NONE', *, *, #89689, .T. ) ; +#94822 = DIRECTION ( 'NONE', ( -0.7071067811865504593, 0.7071067811865445751, 0.000000000000000000 ) ) ; +#94823 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, 3.500000000000000444, 0.000000000000000000 ) ) ; +#94824 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94825 = VECTOR ( 'NONE', #94299, 1000.000000000000000 ) ; +#94826 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #33881 ) ; +#94827 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94829 = EDGE_CURVE ( 'NONE', #26448, #4035, #70550, .T. ) ; +#94828 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #88271, #78698, #49465, #77695 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94831 = VERTEX_POINT ( 'NONE', #62417 ) ; +#94830 = ORIENTED_EDGE ( 'NONE', *, *, #97660, .T. ) ; +#94832 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94833 = ORIENTED_EDGE ( 'NONE', *, *, #7460, .F. ) ; +#94834 = VECTOR ( 'NONE', #78841, 1000.000000000000114 ) ; +#94835 = VERTEX_POINT ( 'NONE', #61915 ) ; +#94836 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39800, 'distance_accuracy_value', 'NONE'); +#94837 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#94838 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 10.50000000000000000, 0.000000000000000000 ) ) ; +#94839 = CARTESIAN_POINT ( 'NONE', ( 0.5141275518124609478, -0.9686402964547039529, 0.8100000000000000533 ) ) ; +#94840 = ORIENTED_EDGE ( 'NONE', *, *, #29295, .F. ) ; +#94841 = EDGE_CURVE ( 'NONE', #65537, #30664, #598, .T. ) ; +#94842 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75341 ), #31312 ) ; +#94843 = FACE_OUTER_BOUND ( 'NONE', #9434, .T. ) ; +#94844 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#94845 = ORIENTED_EDGE ( 'NONE', *, *, #78784, .T. ) ; +#94846 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94847 = VERTEX_POINT ( 'NONE', #53731 ) ; +#94848 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#94849 = VERTEX_POINT ( 'NONE', #62930 ) ; +#94850 = EDGE_LOOP ( 'NONE', ( #82252, #83727, #100484, #4218 ) ) ; +#94851 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#94852 = VECTOR ( 'NONE', #93155, 1000.000000000000000 ) ; +#94853 = CARTESIAN_POINT ( 'NONE', ( -0.2761799387799139804, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#94854 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94855 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, 0.2400000000000000189 ) ) ; +#94856 = STYLED_ITEM ( 'NONE', ( #69618 ), #70065 ) ; +#94858 = ORIENTED_EDGE ( 'NONE', *, *, #74316, .F. ) ; +#94857 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#94859 = FILL_AREA_STYLE ('',( #86220 ) ) ; +#94860 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#94861 = ORIENTED_EDGE ( 'NONE', *, *, #23276, .F. ) ; +#94862 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94863 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363689929, -1.187459415584420030, 0.8299999999999999600 ) ) ; +#94865 = ORIENTED_EDGE ( 'NONE', *, *, #76368, .F. ) ; +#94864 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81878 ), #76966 ) ; +#94866 = ORIENTED_EDGE ( 'NONE', *, *, #5685, .F. ) ; +#94868 = SURFACE_STYLE_USAGE ( .BOTH. , #18274 ) ; +#94867 = SURFACE_SIDE_STYLE ('',( #80115 ) ) ; +#94869 = PLANE ( 'NONE', #66158 ) ; +#94870 = FILL_AREA_STYLE ('',( #70398 ) ) ; +#94871 = CARTESIAN_POINT ( 'NONE', ( -0.3921422844660710227, -1.185705927526510051, 0.8100000000000000533 ) ) ; +#94872 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #87020, #55396, #95137, #54883 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94874 = EDGE_CURVE ( 'NONE', #77784, #83700, #7175, .T. ) ; +#94873 = VECTOR ( 'NONE', #27105, 1000.000000000000000 ) ; +#94875 = EDGE_CURVE ( 'NONE', #87090, #74432, #54245, .T. ) ; +#94876 = CARTESIAN_POINT ( 'NONE', ( -1.480032467532470086, 0.000000000000000000, 0.8299999999999999600 ) ) ; +#94877 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94878 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86008, 'distance_accuracy_value', 'NONE'); +#94879 = FACE_OUTER_BOUND ( 'NONE', #9158, .T. ) ; +#94880 = EDGE_LOOP ( 'NONE', ( #34126, #82448, #80114, #6038 ) ) ; +#94881 = CARTESIAN_POINT ( 'NONE', ( 8.793208999999999165, 3.287228999999999957, 0.8991599999999999593 ) ) ; +#94882 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94883 = EDGE_LOOP ( 'NONE', ( #88601, #65887, #46897, #74941 ) ) ; +#94884 = CIRCLE ( 'NONE', #24840, 0.8059519977764619814 ) ; +#94885 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94886 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#94887 = DIRECTION ( 'NONE', ( -4.720272329281459820E-44, 1.306104834247010004E-29, 1.000000000000000000 ) ) ; +#94889 = SURFACE_STYLE_FILL_AREA ( #87772 ) ; +#94888 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, 0.2749999999999999667, -0.1399999999999999856 ) ) ; +#94890 = CARTESIAN_POINT ( 'NONE', ( 12.75411300000000026, 9.889034999999999798, 0.8991599999999999593 ) ) ; +#94891 = SURFACE_STYLE_USAGE ( .BOTH. , #72436 ) ; +#94892 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94893 = ADVANCED_FACE ( 'NONE', ( #47066 ), #78233, .T. ) ; +#94894 = ADVANCED_FACE ( 'NONE', ( #56791 ), #10700, .T. ) ; +#94895 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94896 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #81904 ) ) ; +#94897 = FILL_AREA_STYLE ('',( #93377 ) ) ; +#94898 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94899 = LINE ( 'NONE', #86774, #56179 ) ; +#94900 = EDGE_CURVE ( 'NONE', #29467, #87237, #34810, .T. ) ; +#94902 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#94901 = STYLED_ITEM ( 'NONE', ( #50240 ), #60041 ) ; +#94903 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37876 ) ) ; +#94904 = VECTOR ( 'NONE', #21355, 1000.000000000000000 ) ; +#94905 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#94906 = DIRECTION ( 'NONE', ( 8.659560562354932858E-17, -0.7071067811865474617, 0.7071067811865474617 ) ) ; +#94907 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #37879 ), #55901 ) ; +#94908 = CARTESIAN_POINT ( 'NONE', ( 2.499999999999989786, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#94909 = SURFACE_STYLE_USAGE ( .BOTH. , #69926 ) ; +#94910 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8073 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76086, #92866, #22986 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#94911 = VECTOR ( 'NONE', #70638, 1000.000000000000000 ) ; +#94912 = EDGE_LOOP ( 'NONE', ( #72514, #25708, #12368, #70506 ) ) ; +#94913 = FACE_OUTER_BOUND ( 'NONE', #26048, .T. ) ; +#94914 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#94915 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80511, 'distance_accuracy_value', 'NONE'); +#94916 = ORIENTED_EDGE ( 'NONE', *, *, #21978, .T. ) ; +#94918 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82651, 'distance_accuracy_value', 'NONE'); +#94917 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94919 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#94920 = ADVANCED_FACE ( 'NONE', ( #26138 ), #17918, .T. ) ; +#94921 = CARTESIAN_POINT ( 'NONE', ( 1.874899521751800080, -1.024811280222130083, 0.8299999999999999600 ) ) ; +#94922 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#94923 = STYLED_ITEM ( 'NONE', ( #48894 ), #66585 ) ; +#94924 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -1.099999999999999867, 0.1829999999999620264 ) ) ; +#94925 = EDGE_CURVE ( 'NONE', #74502, #82928, #49124, .T. ) ; +#94926 = VECTOR ( 'NONE', #40995, 1000.000000000000000 ) ; +#94927 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94928 = ORIENTED_EDGE ( 'NONE', *, *, #7679, .T. ) ; +#94929 = ORIENTED_EDGE ( 'NONE', *, *, #76273, .F. ) ; +#94930 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #58344, #96567, #89447, #90436, #19493, #20490, #26174, #57322, #88435, #11733, #18472, #49656, #80802 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 2, 4 ), + ( 0.000000000000000000, 0.2500000000000007772, 0.3125000000000003331, 0.3749999999999999445, 0.5000000000000006661, 0.7500000000000003331, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#94931 = STYLED_ITEM ( 'NONE', ( #82233 ), #70576 ) ; +#94932 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64849, 'distance_accuracy_value', 'NONE'); +#94933 = CARTESIAN_POINT ( 'NONE', ( 1.479999999999999982, 0.1600000000000000033, -1.250000000000000000 ) ) ; +#94934 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#94935 = EDGE_CURVE ( 'NONE', #40138, #35018, #88910, .T. ) ; +#94936 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8991599999999999593 ) ) ; +#94937 = SURFACE_STYLE_FILL_AREA ( #10099 ) ; +#94938 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, -3.499999999999989786, -0.02000000000000000042 ) ) ; +#94939 = SURFACE_STYLE_FILL_AREA ( #26552 ) ; +#94940 = FACE_OUTER_BOUND ( 'NONE', #64363, .T. ) ; +#94941 = VECTOR ( 'NONE', #3673, 1000.000000000000000 ) ; +#94942 = ORIENTED_EDGE ( 'NONE', *, *, #93509, .F. ) ; +#94943 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #3333 ) ) ; +#94944 = LINE ( 'NONE', #520, #89239 ) ; +#94945 = DIRECTION ( 'NONE', ( -0.7071075504167436687, -0.7071060119555145906, 0.000000000000000000 ) ) ; +#94946 = ORIENTED_EDGE ( 'NONE', *, *, #99107, .F. ) ; +#94947 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#94948 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75371 ), #6837 ) ; +#94949 = VERTEX_POINT ( 'NONE', #56281 ) ; +#94950 = SURFACE_SIDE_STYLE ('',( #79164 ) ) ; +#94951 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #34667 ), #6842 ) ; +#94952 = SURFACE_STYLE_FILL_AREA ( #48024 ) ; +#94953 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#94954 = DIRECTION ( 'NONE', ( -0.7071090539100497452, -0.7071045084557405769, 0.000000000000000000 ) ) ; +#94955 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#94956 = SURFACE_STYLE_FILL_AREA ( #71510 ) ; +#94957 = EDGE_CURVE ( 'NONE', #35525, #68214, #48618, .T. ) ; +#94958 = FILL_AREA_STYLE ('',( #49052 ) ) ; +#94960 = ORIENTED_EDGE ( 'NONE', *, *, #80206, .F. ) ; +#94959 = ORIENTED_EDGE ( 'NONE', *, *, #37366, .T. ) ; +#94961 = CARTESIAN_POINT ( 'NONE', ( 9.358893999999999380, 8.675382000000000815, 0.8991599999999999593 ) ) ; +#94962 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#94963 = ORIENTED_EDGE ( 'NONE', *, *, #50981, .F. ) ; +#94964 = CARTESIAN_POINT ( 'NONE', ( 5.618299000000000376, 7.324807999999999986, 0.8648700000000000276 ) ) ; +#94965 = STYLED_ITEM ( 'NONE', ( #21213 ), #19429 ) ; +#94966 = LINE ( 'NONE', #25090, #84765 ) ; +#94967 = ORIENTED_EDGE ( 'NONE', *, *, #85248, .F. ) ; +#94968 = ADVANCED_FACE ( 'NONE', ( #66426 ), #83762, .T. ) ; +#94969 = ORIENTED_EDGE ( 'NONE', *, *, #10731, .F. ) ; +#94970 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#94971 = CARTESIAN_POINT ( 'NONE', ( 13.45907599999999960, 11.26597300000000068, 0.8648700000000000276 ) ) ; +#94972 = FACE_OUTER_BOUND ( 'NONE', #13820, .T. ) ; +#94973 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#94975 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999960121, -1.350000000000000089, 0.000000000000000000 ) ) ; +#94974 = SURFACE_STYLE_USAGE ( .BOTH. , #16350 ) ; +#94976 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#94977 = ORIENTED_EDGE ( 'NONE', *, *, #54473, .T. ) ; +#94978 = ADVANCED_FACE ( 'NONE', ( #52134 ), #90404, .F. ) ; +#94979 = VERTEX_POINT ( 'NONE', #74094 ) ; +#94980 = FILL_AREA_STYLE_COLOUR ( '', #30700 ) ; +#94981 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #67295 ) ) ; +#94982 = ORIENTED_EDGE ( 'NONE', *, *, #91403, .T. ) ; +#94983 = STYLED_ITEM ( 'NONE', ( #57963 ), #36422 ) ; +#94984 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#94985 = EDGE_CURVE ( 'NONE', #68360, #85984, #27655, .T. ) ; +#94986 = ORIENTED_EDGE ( 'NONE', *, *, #75641, .F. ) ; +#94987 = DIRECTION ( 'NONE', ( 0.7071067811865469066, -0.7071067811865482389, 0.000000000000000000 ) ) ; +#94988 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37955 ) ) ; +#94989 = CARTESIAN_POINT ( 'NONE', ( 0.5644277597402590496, 0.6899999999999999467, 0.1493506493506490118 ) ) ; +#94990 = CARTESIAN_POINT ( 'NONE', ( 1.840728708308520201, -1.463352833475739967, 0.8099999999999996092 ) ) ; +#94991 = ORIENTED_EDGE ( 'NONE', *, *, #83592, .T. ) ; +#94992 = LINE ( 'NONE', #80732, #37902 ) ; +#94993 = EDGE_LOOP ( 'NONE', ( #60120, #69058, #55232, #33271 ) ) ; +#94994 = LINE ( 'NONE', #64891, #36727 ) ; +#94995 = CARTESIAN_POINT ( 'NONE', ( 10.27073299999999989, 12.86860300000000024, 0.8991599999999999593 ) ) ; +#94996 = CARTESIAN_POINT ( 'NONE', ( 3.700000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#94998 = ADVANCED_FACE ( 'NONE', ( #4137 ), #44910, .T. ) ; +#94997 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.75342000000000020, 0.8648700000000000276 ) ) ; +#94999 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#95000 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333330195, 1.500000000000000000, 0.000000000000000000 ) ) ; +#95001 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95002 = CARTESIAN_POINT ( 'NONE', ( 1.634048567103850047, -0.9784189978443861291, 0.8299999999999990719 ) ) ; +#95003 = CARTESIAN_POINT ( 'NONE', ( 1.687860199445399889, -1.507611749840819915, 0.8099999999999982769 ) ) ; +#95004 = CARTESIAN_POINT ( 'NONE', ( 1.711221411465380093, -1.219829592979950084, 0.8099999999999996092 ) ) ; +#95005 = EDGE_LOOP ( 'NONE', ( #46396, #30237, #73639, #7660 ) ) ; +#95006 = VECTOR ( 'NONE', #86103, 1000.000000000000000 ) ; +#95007 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.500000000000000000, -0.02000000000000630093 ) ) ; +#95008 = FILL_AREA_STYLE_COLOUR ( '', #44886 ) ; +#95009 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999990841, 0.8199999999999998401, -0.04999999999999995420 ) ) ; +#95010 = STYLED_ITEM ( 'NONE', ( #92321 ), #53128 ) ; +#95012 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.383333333333333304, 1.747825839085088807E-76 ) ) ; +#95011 = SURFACE_SIDE_STYLE ('',( #32765 ) ) ; +#95013 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999937383, 3.500000000000000444, 0.000000000000000000 ) ) ; +#95014 = EDGE_CURVE ( 'NONE', #21356, #88846, #99955, .T. ) ; +#95015 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95016 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95017 = EDGE_CURVE ( 'NONE', #59269, #51456, #53623, .T. ) ; +#95018 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95019 = FILL_AREA_STYLE_COLOUR ( '', #18854 ) ; +#95020 = FILL_AREA_STYLE_COLOUR ( '', #100023 ) ; +#95021 = VERTEX_POINT ( 'NONE', #85251 ) ; +#95022 = PRESENTATION_STYLE_ASSIGNMENT (( #49624 ) ) ; +#95024 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 4.524664999999999715, 0.8991599999999999593 ) ) ; +#95023 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88568 ), #28238 ) ; +#95025 = DIRECTION ( 'NONE', ( -0.9361199317767866512, 0.000000000000000000, -0.3516809254569038812 ) ) ; +#95026 = SURFACE_STYLE_USAGE ( .BOTH. , #31255 ) ; +#95027 = VECTOR ( 'NONE', #14509, 1000.000000000000114 ) ; +#95028 = VECTOR ( 'NONE', #87910, 1000.000000000000000 ) ; +#95029 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#95030 = ORIENTED_EDGE ( 'NONE', *, *, #534, .T. ) ; +#95031 = PLANE ( 'NONE', #96260 ) ; +#95032 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#95033 = PLANE ( 'NONE', #44925 ) ; +#95034 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95035 = ADVANCED_FACE ( 'NONE', ( #22465 ), #16283, .T. ) ; +#95036 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78732 ), #33131 ) ; +#95037 = CARTESIAN_POINT ( 'NONE', ( 9.640700000000000713, 11.54881500000000116, 0.8991599999999999593 ) ) ; +#95038 = SURFACE_STYLE_FILL_AREA ( #33307 ) ; +#95039 = LINE ( 'NONE', #25169, #2372 ) ; +#95041 = AXIS2_PLACEMENT_3D ( 'NONE', #59227, #27057, #18342 ) ; +#95040 = CARTESIAN_POINT ( 'NONE', ( 0.8322849025974019543, 0.6899999999999999467, 8.923404656952782542E-18 ) ) ; +#95042 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40618, 'distance_accuracy_value', 'NONE'); +#95043 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #26597 ) ) ; +#95044 = ADVANCED_FACE ( 'NONE', ( #92868 ), #21965, .T. ) ; +#95045 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95046 = SURFACE_STYLE_USAGE ( .BOTH. , #63948 ) ; +#95047 = ORIENTED_EDGE ( 'NONE', *, *, #50089, .T. ) ; +#95048 = FILL_AREA_STYLE ('',( #18463 ) ) ; +#95049 = ADVANCED_FACE ( 'NONE', ( #16786 ), #47968, .T. ) ; +#95051 = ORIENTED_EDGE ( 'NONE', *, *, #66771, .F. ) ; +#95050 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95052 = FACE_OUTER_BOUND ( 'NONE', #51447, .T. ) ; +#95053 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #27531, 'distance_accuracy_value', 'NONE'); +#95054 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40290, 'distance_accuracy_value', 'NONE'); +#95055 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95056 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.4397321428571430713 ) ) ; +#95057 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95058 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8991599999999999593 ) ) ; +#95059 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2822 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53463, #15615, #92229 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95060 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#95061 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95062 = FILL_AREA_STYLE ('',( #34351 ) ) ; +#95063 = ORIENTED_EDGE ( 'NONE', *, *, #76308, .T. ) ; +#95064 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95065 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95066 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #96037, 'distance_accuracy_value', 'NONE'); +#95067 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95068 = VERTEX_POINT ( 'NONE', #57688 ) ; +#95069 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 1.149999999999999911, 0.000000000000000000 ) ) ; +#95070 = ORIENTED_EDGE ( 'NONE', *, *, #71629, .T. ) ; +#95071 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #100293, #20806, #90755, #53959 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95072 = FILL_AREA_STYLE ('',( #25199 ) ) ; +#95073 = FACE_OUTER_BOUND ( 'NONE', #91459, .T. ) ; +#95074 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#95076 = ORIENTED_EDGE ( 'NONE', *, *, #4581, .T. ) ; +#95075 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #73911 ) ) ; +#95077 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#95078 = VERTEX_POINT ( 'NONE', #88789 ) ; +#95079 = CARTESIAN_POINT ( 'NONE', ( -0.8333333333333386994, 3.500000000000000000, 0.000000000000000000 ) ) ; +#95080 = STYLED_ITEM ( 'NONE', ( #26825 ), #53197 ) ; +#95081 = CARTESIAN_POINT ( 'NONE', ( 0.4626002664603570125, -1.036644144574919935, 0.8300000000000002931 ) ) ; +#95082 = EDGE_CURVE ( 'NONE', #17384, #100207, #86773, .T. ) ; +#95083 = EDGE_LOOP ( 'NONE', ( #76629, #4209, #53634, #8305 ) ) ; +#95084 = LINE ( 'NONE', #73161, #48123 ) ; +#95085 = LINE ( 'NONE', #48165, #51230 ) ; +#95086 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95087 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95088 = FILL_AREA_STYLE_COLOUR ( '', #68337 ) ; +#95089 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -2.500000000000000000, 0.8299999999999999600 ) ) ; +#95090 = ORIENTED_EDGE ( 'NONE', *, *, #39039, .F. ) ; +#95091 = EDGE_CURVE ( 'NONE', #20794, #97015, #64297, .T. ) ; +#95093 = ORIENTED_EDGE ( 'NONE', *, *, #57349, .F. ) ; +#95092 = ORIENTED_EDGE ( 'NONE', *, *, #93067, .T. ) ; +#95094 = STYLED_ITEM ( 'NONE', ( #77484 ), #47439 ) ; +#95095 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98729 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #4911, #53786, #82562 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95096 = VERTEX_POINT ( 'NONE', #41831 ) ; +#95097 = CARTESIAN_POINT ( 'NONE', ( 1.864761241546880166, -1.121240070007210043, 0.8299999999999995159 ) ) ; +#95098 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3872 ) ) ; +#95099 = EDGE_CURVE ( 'NONE', #5293, #75645, #60430, .T. ) ; +#95100 = EDGE_LOOP ( 'NONE', ( #56268, #80219, #23975, #83616 ) ) ; +#95101 = EDGE_LOOP ( 'NONE', ( #94342, #46568, #13054, #22422 ) ) ; +#95102 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.8500000000000000888, -0.5799999999999999600 ) ) ; +#95103 = VECTOR ( 'NONE', #39578, 1000.000000000000000 ) ; +#95104 = SURFACE_SIDE_STYLE ('',( #94613 ) ) ; +#95105 = ORIENTED_EDGE ( 'NONE', *, *, #83274, .T. ) ; +#95107 = EDGE_CURVE ( 'NONE', #24062, #30895, #3533, .T. ) ; +#95106 = PRESENTATION_STYLE_ASSIGNMENT (( #71669 ) ) ; +#95108 = SURFACE_STYLE_USAGE ( .BOTH. , #46646 ) ; +#95109 = ORIENTED_EDGE ( 'NONE', *, *, #86992, .T. ) ; +#95110 = STYLED_ITEM ( 'NONE', ( #47922 ), #18949 ) ; +#95111 = SURFACE_STYLE_USAGE ( .BOTH. , #64009 ) ; +#95112 = VECTOR ( 'NONE', #99243, 1000.000000000000000 ) ; +#95113 = PRESENTATION_STYLE_ASSIGNMENT (( #56391 ) ) ; +#95114 = EDGE_LOOP ( 'NONE', ( #55337, #98543, #73548, #66762 ) ) ; +#95115 = EDGE_LOOP ( 'NONE', ( #6152, #6616, #60247, #4684 ) ) ; +#95116 = VECTOR ( 'NONE', #26999, 1000.000000000000000 ) ; +#95117 = ADVANCED_FACE ( 'NONE', ( #25023 ), #48999, .T. ) ; +#95118 = EDGE_CURVE ( 'NONE', #27603, #91027, #64795, .T. ) ; +#95119 = VECTOR ( 'NONE', #80181, 1000.000000000000114 ) ; +#95121 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#95120 = DIRECTION ( 'NONE', ( 0.9408821649279537347, 0.000000000000000000, -0.3387340427540269649 ) ) ; +#95122 = CARTESIAN_POINT ( 'NONE', ( 11.70000000000000107, 1.149999999999999911, 0.000000000000000000 ) ) ; +#95123 = EDGE_CURVE ( 'NONE', #66963, #49704, #14351, .T. ) ; +#95124 = FACE_OUTER_BOUND ( 'NONE', #92082, .T. ) ; +#95125 = ADVANCED_FACE ( 'NONE', ( #13608 ), #83141, .T. ) ; +#95126 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95128 = FILL_AREA_STYLE ('',( #78834 ) ) ; +#95127 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.455799999999999983, 0.8648700000000000276 ) ) ; +#95129 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95130 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, -0.005000000000000000104, -0.1400000000000000133 ) ) ; +#95131 = EDGE_CURVE ( 'NONE', #10619, #28081, #43507, .T. ) ; +#95132 = VECTOR ( 'NONE', #16974, 1000.000000000000114 ) ; +#95133 = CARTESIAN_POINT ( 'NONE', ( -1.147844963924800066, -0.8845642871695170717, 0.8299999999999999600 ) ) ; +#95134 = CARTESIAN_POINT ( 'NONE', ( 0.9994445003280740814, -0.9813977598329840513, 0.8299999999999999600 ) ) ; +#95135 = EDGE_LOOP ( 'NONE', ( #88988, #45167, #83686, #88562 ) ) ; +#95136 = FACE_BOUND ( 'NONE', #22093, .T. ) ; +#95137 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.723820061220085131, -0.02000000000000000042 ) ) ; +#95138 = FILL_AREA_STYLE ('',( #87510 ) ) ; +#95139 = ORIENTED_EDGE ( 'NONE', *, *, #21900, .T. ) ; +#95140 = LINE ( 'NONE', #57406, #8908 ) ; +#95141 = LINE ( 'NONE', #17045, #10310 ) ; +#95144 = SURFACE_STYLE_USAGE ( .BOTH. , #48237 ) ; +#95143 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95142 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95145 = CARTESIAN_POINT ( 'NONE', ( 8.969984999999999431, 2.544766999999999779, 0.8648700000000000276 ) ) ; +#95146 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95147 = CARTESIAN_POINT ( 'NONE', ( 7.739619000000000248, 7.324807999999999986, 0.8991599999999999593 ) ) ; +#95148 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#95149 = FILL_AREA_STYLE ('',( #41086 ) ) ; +#95150 = ORIENTED_EDGE ( 'NONE', *, *, #54363, .F. ) ; +#95151 = LINE ( 'NONE', #54389, #88066 ) ; +#95152 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999467, -3.149999999999999911, 0.000000000000000000 ) ) ; +#95153 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#95154 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95155 = STYLED_ITEM ( 'NONE', ( #15907 ), #88465 ) ; +#95156 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#95157 = CARTESIAN_POINT ( 'NONE', ( -0.9238200612200850870, -3.099999999999989875, 0.000000000000000000 ) ) ; +#95158 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#95159 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95160 = VECTOR ( 'NONE', #98148, 1000.000000000000000 ) ; +#95161 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8654 ) ) ; +#95162 = PRESENTATION_STYLE_ASSIGNMENT (( #77862 ) ) ; +#95163 = LINE ( 'NONE', #87548, #1241 ) ; +#95164 = FACE_OUTER_BOUND ( 'NONE', #39005, .T. ) ; +#95165 = STYLED_ITEM ( 'NONE', ( #23734 ), #76817 ) ; +#95166 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95167 = EDGE_LOOP ( 'NONE', ( #91979, #95691, #53402, #77163 ) ) ; +#95168 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95169 = ADVANCED_FACE ( 'NONE', ( #13102 ), #5963, .T. ) ; +#95170 = ORIENTED_EDGE ( 'NONE', *, *, #11005, .T. ) ; +#95171 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #81360, 'distance_accuracy_value', 'NONE'); +#95172 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58503, 'distance_accuracy_value', 'NONE'); +#95173 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -1.500000000000000000, -1.195472123049164304E-89 ) ) ; +#95174 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2808578643762690841, 0.1499999999999999667 ) ) ; +#95175 = FILL_AREA_STYLE ('',( #64083 ) ) ; +#95176 = STYLED_ITEM ( 'NONE', ( #97306 ), #20062 ) ; +#95177 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4000000000000000222, -0.2999999999999999889 ) ) ; +#95179 = EDGE_CURVE ( 'NONE', #49397, #82810, #67786, .T. ) ; +#95178 = SURFACE_STYLE_USAGE ( .BOTH. , #88556 ) ; +#95180 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77954, #85605, #16138, #64159 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95181 = VECTOR ( 'NONE', #6817, 1000.000000000000000 ) ; +#95182 = VERTEX_POINT ( 'NONE', #19331 ) ; +#95183 = FILL_AREA_STYLE ('',( #9859 ) ) ; +#95184 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #35527, 'distance_accuracy_value', 'NONE'); +#95186 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85906 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38871, #45, #69477 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95185 = SURFACE_STYLE_FILL_AREA ( #2810 ) ; +#95187 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95188 = ORIENTED_EDGE ( 'NONE', *, *, #9104, .F. ) ; +#95189 = LINE ( 'NONE', #9374, #23358 ) ; +#95190 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95191 = CARTESIAN_POINT ( 'NONE', ( 9.252827750249974059, 9.700686750249976953, 0.8648700000000000276 ) ) ; +#95192 = FILL_AREA_STYLE_COLOUR ( '', #62164 ) ; +#95193 = EDGE_CURVE ( 'NONE', #100905, #46216, #81658, .T. ) ; +#95194 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#95195 = VERTEX_POINT ( 'NONE', #4019 ) ; +#95196 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95197 = VECTOR ( 'NONE', #29566, 1000.000000000000000 ) ; +#95198 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30550, 'distance_accuracy_value', 'NONE'); +#95199 = CARTESIAN_POINT ( 'NONE', ( 1.194399350649350211, -0.9545454545454551409, 0.8299999999999999600 ) ) ; +#95200 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #99996 ) ) ; +#95201 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#95202 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8991599999999999593 ) ) ; +#95203 = ORIENTED_EDGE ( 'NONE', *, *, #81038, .F. ) ; +#95204 = FILL_AREA_STYLE ('',( #50820 ) ) ; +#95205 = FILL_AREA_STYLE ('',( #41137 ) ) ; +#95206 = STYLED_ITEM ( 'NONE', ( #65984 ), #67522 ) ; +#95207 = VERTEX_POINT ( 'NONE', #4506 ) ; +#95208 = CARTESIAN_POINT ( 'NONE', ( 10.21449299999999916, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#95209 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95210 = AXIS2_PLACEMENT_3D ( 'NONE', #23311, #5560, #67857 ) ; +#95211 = ORIENTED_EDGE ( 'NONE', *, *, #22179, .T. ) ; +#95213 = VERTEX_POINT ( 'NONE', #82639 ) ; +#95212 = CARTESIAN_POINT ( 'NONE', ( 2.443541999999999881, 15.09753200000000106, 0.8991599999999999593 ) ) ; +#95215 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.350000000000000089, 0.000000000000000000 ) ) ; +#95214 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95216 = ADVANCED_FACE ( 'NONE', ( #92757 ), #84136, .F. ) ; +#95217 = LINE ( 'NONE', #79453, #31254 ) ; +#95218 = ORIENTED_EDGE ( 'NONE', *, *, #34311, .F. ) ; +#95219 = LINE ( 'NONE', #32981, #59757 ) ; +#95220 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95221 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95222 = ORIENTED_EDGE ( 'NONE', *, *, #48763, .F. ) ; +#95223 = PRESENTATION_STYLE_ASSIGNMENT (( #72283 ) ) ; +#95224 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93606 ) ) ; +#95225 = ORIENTED_EDGE ( 'NONE', *, *, #64942, .F. ) ; +#95226 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43079 ) ) ; +#95227 = EDGE_LOOP ( 'NONE', ( #20651, #28784, #67694, #41653 ) ) ; +#95228 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999992895, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#95229 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95230 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #95165 ), #88714 ) ; +#95231 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49870 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78026, #8482, #39719 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95232 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95233 = ORIENTED_EDGE ( 'NONE', *, *, #72693, .F. ) ; +#95234 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95235 = EDGE_CURVE ( 'NONE', #49180, #37187, #23366, .T. ) ; +#95236 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4028 ) ) ; +#95237 = LINE ( 'NONE', #56518, #57231 ) ; +#95238 = ORIENTED_EDGE ( 'NONE', *, *, #83415, .T. ) ; +#95239 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95240 = PLANE ( 'NONE', #91888 ) ; +#95241 = EDGE_LOOP ( 'NONE', ( #80812, #19489, #60918, #22620 ) ) ; +#95242 = ORIENTED_EDGE ( 'NONE', *, *, #48807, .F. ) ; +#95243 = FILL_AREA_STYLE_COLOUR ( '', #27449 ) ; +#95245 = FACE_OUTER_BOUND ( 'NONE', #57131, .T. ) ; +#95244 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 2.149999999999999911, -0.02000000000000000042 ) ) ; +#95246 = SURFACE_STYLE_FILL_AREA ( #87132 ) ; +#95247 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95248 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#95250 = AXIS2_PLACEMENT_3D ( 'NONE', #59444, #60436, #20577 ) ; +#95249 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39898 ) ) ; +#95251 = EDGE_CURVE ( 'NONE', #73420, #89974, #37193, .T. ) ; +#95252 = VECTOR ( 'NONE', #100821, 1000.000000000000114 ) ; +#95253 = VECTOR ( 'NONE', #7051, 1000.000000000000000 ) ; +#95254 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95255 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95256 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#95257 = EDGE_CURVE ( 'NONE', #19790, #82605, #53009, .T. ) ; +#95258 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95259 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95260 = VERTEX_POINT ( 'NONE', #62191 ) ; +#95261 = SURFACE_SIDE_STYLE ('',( #33539 ) ) ; +#95262 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.3800000000637737685, 0.000000000000000000 ) ) ; +#95263 = FILL_AREA_STYLE_COLOUR ( '', #98662 ) ; +#95264 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95265 = LINE ( 'NONE', #56540, #1204 ) ; +#95266 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999998898659, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#95267 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10371 ), #96877 ) ; +#95268 = FILL_AREA_STYLE ('',( #64174 ) ) ; +#95269 = LINE ( 'NONE', #96283, #20825 ) ; +#95270 = CARTESIAN_POINT ( 'NONE', ( 1.990991862329345219, 1.450000000003623946, -11.37416661673220020 ) ) ; +#95271 = FACE_OUTER_BOUND ( 'NONE', #94323, .T. ) ; +#95272 = ORIENTED_EDGE ( 'NONE', *, *, #17852, .F. ) ; +#95273 = CARTESIAN_POINT ( 'NONE', ( 4.691989000000000409, 7.954133000000000564, 0.8991599999999999593 ) ) ; +#95274 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#95275 = PRESENTATION_STYLE_ASSIGNMENT (( #10437 ) ) ; +#95276 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#95277 = VECTOR ( 'NONE', #27077, 1000.000000000000000 ) ; +#95278 = SURFACE_SIDE_STYLE ('',( #71330 ) ) ; +#95279 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18526, 'distance_accuracy_value', 'NONE'); +#95280 = CYLINDRICAL_SURFACE ( 'NONE', #90482, 0.01000000000000002623 ) ; +#95281 = VECTOR ( 'NONE', #59405, 1000.000000000000000 ) ; +#95282 = FILL_AREA_STYLE ('',( #35075 ) ) ; +#95283 = PLANE ( 'NONE', #34819 ) ; +#95284 = PRESENTATION_STYLE_ASSIGNMENT (( #73367 ) ) ; +#95285 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95286 = VECTOR ( 'NONE', #28860, 1000.000000000000000 ) ; +#95287 = PLANE ( 'NONE', #56818 ) ; +#95288 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95289 = PRESENTATION_STYLE_ASSIGNMENT (( #24407 ) ) ; +#95290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95291 = VECTOR ( 'NONE', #6590, 1000.000000000000114 ) ; +#95292 = VECTOR ( 'NONE', #20954, 1000.000000000000000 ) ; +#95294 = EDGE_CURVE ( 'NONE', #36176, #41373, #46816, .T. ) ; +#95293 = CARTESIAN_POINT ( 'NONE', ( 1.399999999999999911, 0.4600000000000000200, 0.8000000000000000444 ) ) ; +#95295 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.004999999999999986226, -0.2500000000000000000 ) ) ; +#95296 = ORIENTED_EDGE ( 'NONE', *, *, #28619, .F. ) ; +#95297 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95298 = LINE ( 'NONE', #3437, #53413 ) ; +#95299 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66597 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22223, #67655, #30354 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95300 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28479, 'distance_accuracy_value', 'NONE'); +#95302 = FILL_AREA_STYLE ('',( #18719 ) ) ; +#95301 = FACE_OUTER_BOUND ( 'NONE', #1891, .T. ) ; +#95303 = CARTESIAN_POINT ( 'NONE', ( 1.098827447008967173, -1.417370842016850041, 0.8099999999997277156 ) ) ; +#95304 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #12103 ), #72525 ) ; +#95305 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95306 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.258441558441560026, 0.8299999999999999600 ) ) ; +#95307 = FILL_AREA_STYLE_COLOUR ( '', #51665 ) ; +#95308 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#95309 = ORIENTED_EDGE ( 'NONE', *, *, #81912, .F. ) ; +#95310 = SURFACE_STYLE_FILL_AREA ( #24941 ) ; +#95311 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.000000000000000000, 0.2500000000000000000 ) ) ; +#95312 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95313 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #13782, 'distance_accuracy_value', 'NONE'); +#95314 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, 0.4850000000000000977, 0.2399999999999999634 ) ) ; +#95315 = STYLED_ITEM ( 'NONE', ( #39159 ), #28538 ) ; +#95316 = VECTOR ( 'NONE', #78381, 1000.000000000000000 ) ; +#95317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98478, 'distance_accuracy_value', 'NONE'); +#95318 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82328 ), #53019 ) ; +#95319 = EDGE_CURVE ( 'NONE', #81461, #38123, #22338, .T. ) ; +#95320 = ORIENTED_EDGE ( 'NONE', *, *, #30049, .T. ) ; +#95321 = ORIENTED_EDGE ( 'NONE', *, *, #69105, .F. ) ; +#95322 = STYLED_ITEM ( 'NONE', ( #34392 ), #38665 ) ; +#95323 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #21974 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61565, #53376, #36067 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95324 = CARTESIAN_POINT ( 'NONE', ( 0.5000000000000006661, 3.149999999999979927, 1.048695503451053346E-76 ) ) ; +#95325 = SURFACE_STYLE_FILL_AREA ( #64227 ) ; +#95326 = VERTEX_POINT ( 'NONE', #60670 ) ; +#95327 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95328 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.94293799999999983, 0.8648700000000000276 ) ) ; +#95329 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#95330 = FILL_AREA_STYLE_COLOUR ( '', #33478 ) ; +#95331 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95332 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83925 ) ) ; +#95333 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #99633 ) ; +#95334 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95336 = ORIENTED_EDGE ( 'NONE', *, *, #14524, .F. ) ; +#95335 = VERTEX_POINT ( 'NONE', #29509 ) ; +#95337 = ORIENTED_EDGE ( 'NONE', *, *, #32251, .F. ) ; +#95338 = FILL_AREA_STYLE_COLOUR ( '', #24692 ) ; +#95339 = STYLED_ITEM ( 'NONE', ( #58782 ), #12322 ) ; +#95340 = CARTESIAN_POINT ( 'NONE', ( 1.826147860666869960, -1.473933850988760064, 0.8100000000000000533 ) ) ; +#95341 = FILL_AREA_STYLE ('',( #63759 ) ) ; +#95342 = ORIENTED_EDGE ( 'NONE', *, *, #21584, .T. ) ; +#95343 = ADVANCED_FACE ( 'NONE', ( #100334 ), #82525, .T. ) ; +#95344 = CARTESIAN_POINT ( 'NONE', ( 1.499999999999990008, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#95345 = STYLED_ITEM ( 'NONE', ( #91097 ), #68200 ) ; +#95346 = VERTEX_POINT ( 'NONE', #90151 ) ; +#95347 = FILL_AREA_STYLE ('',( #40776 ) ) ; +#95348 = ORIENTED_EDGE ( 'NONE', *, *, #70176, .F. ) ; +#95349 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93284 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71039, #8153, #33765 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95351 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95350 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, -3.099999999999980549, 0.000000000000000000 ) ) ; +#95352 = VERTEX_POINT ( 'NONE', #74358 ) ; +#95353 = ORIENTED_EDGE ( 'NONE', *, *, #86726, .F. ) ; +#95354 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#95355 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95356 = AXIS2_PLACEMENT_3D ( 'NONE', #93086, #46651, #77808 ) ; +#95357 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95358 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95359 = CARTESIAN_POINT ( 'NONE', ( 4.564709999999999823, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#95361 = ORIENTED_EDGE ( 'NONE', *, *, #61871, .F. ) ; +#95360 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95362 = CARTESIAN_POINT ( 'NONE', ( 1.793303571428570109, -1.187459415584420030, 0.8100000000000000533 ) ) ; +#95363 = EDGE_CURVE ( 'NONE', #43496, #46722, #65343, .T. ) ; +#95364 = PRESENTATION_STYLE_ASSIGNMENT (( #64257 ) ) ; +#95365 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #96977 ) ) ; +#95366 = LINE ( 'NONE', #25479, #62024 ) ; +#95367 = VERTEX_POINT ( 'NONE', #29390 ) ; +#95368 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#95369 = LINE ( 'NONE', #63780, #88551 ) ; +#95370 = EDGE_LOOP ( 'NONE', ( #19420, #66231, #31694, #20523 ) ) ; +#95371 = ORIENTED_EDGE ( 'NONE', *, *, #34619, .T. ) ; +#95372 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95373 = VECTOR ( 'NONE', #56080, 1000.000000000000000 ) ; +#95374 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959943, -0.02000000000000000042 ) ) ; +#95375 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95376 = FILL_AREA_STYLE_COLOUR ( '', #41760 ) ; +#95377 = VECTOR ( 'NONE', #53088, 1000.000000000000000 ) ; +#95378 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #47103 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7361, #100745, #60109 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95379 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23235 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #78687, #32753, #570 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95380 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #89248, #29459 ), + ( #13050, #74927 ), + ( #50960, #60139 ), + ( #83595, #74431 ), + ( #20790, #67246 ), + ( #51960, #5917 ), + ( #75917, #75413 ), + ( #90231, #43761 ), + ( #11540, #21286 ), + ( #20277, #60624 ), + ( #42774, #83090 ), + ( #36641, #44252 ), + ( #4458, #67735 ), + ( #52964, #98809 ), + ( #35144, #97838 ), + ( #91237, #52448 ), + ( #13551, #68232 ), + ( #27980, #44747 ), + ( #66261, #99313 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06539851322094759889, 0.1302892112916909928, 0.1949613880993550097, 0.2597072667505109789, 0.3233315164440599965, 0.3849649931167469785, 0.4455304668157999970, 0.5050074906119650375, 0.5637094320295910066, 0.6217643038656149868, 0.6805306891948610382, 0.7399249246528789570, 0.8006913001071930269, 0.8636024226288889771, 0.9298736828390290476, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95381 = CARTESIAN_POINT ( 'NONE', ( 6.389045000000000307, 9.651189000000000462, 0.8991599999999999593 ) ) ; +#95382 = ADVANCED_FACE ( 'NONE', ( #51390 ), #66676, .F. ) ; +#95383 = CARTESIAN_POINT ( 'NONE', ( 10.08014287512504126, 4.574162875125044714, 0.8991599999999999593 ) ) ; +#95384 = ORIENTED_EDGE ( 'NONE', *, *, #2835, .T. ) ; +#95385 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, -3.500000000000000444, 0.000000000000000000 ) ) ; +#95386 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3308 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42520, #48678, #32837 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95387 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#95388 = ORIENTED_EDGE ( 'NONE', *, *, #63895, .F. ) ; +#95389 = LINE ( 'NONE', #56659, #73344 ) ; +#95390 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95391 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95392 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 3.569275000000000198, 0.8991599999999999593 ) ) ; +#95393 = VECTOR ( 'NONE', #3164, 1000.000000000000000 ) ; +#95395 = DIRECTION ( 'NONE', ( 0.7071067834590476497, 0.7071067789140474957, 0.000000000000000000 ) ) ; +#95394 = LINE ( 'NONE', #48987, #90310 ) ; +#95397 = AXIS2_PLACEMENT_3D ( 'NONE', #5260, #75263, #36464 ) ; +#95396 = FACE_OUTER_BOUND ( 'NONE', #49979, .T. ) ; +#95398 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95399 = CARTESIAN_POINT ( 'NONE', ( -0.7229898940154579901, 0.6774732877316049784, 0.8299999999999999600 ) ) ; +#95401 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95400 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86936 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #42537, #74687, #73186 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95402 = CARTESIAN_POINT ( 'NONE', ( 3.383333333333320425, -0.7000000000000009548, 1.747825839084689943E-76 ) ) ; +#95403 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95404 = FACE_OUTER_BOUND ( 'NONE', #24608, .T. ) ; +#95405 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95406 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#95407 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95408 = VECTOR ( 'NONE', #60544, 1000.000000000000000 ) ; +#95409 = EDGE_CURVE ( 'NONE', #13861, #50104, #5359, .T. ) ; +#95410 = SURFACE_STYLE_FILL_AREA ( #25518 ) ; +#95411 = SURFACE_STYLE_USAGE ( .BOTH. , #80652 ) ; +#95412 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333313320, -2.700000000000000178, 1.747825839084491125E-76 ) ) ; +#95413 = SURFACE_SIDE_STYLE ('',( #41344 ) ) ; +#95414 = PRESENTATION_STYLE_ASSIGNMENT (( #97424 ) ) ; +#95415 = VECTOR ( 'NONE', #91389, 1000.000000000000000 ) ; +#95416 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1899, 'distance_accuracy_value', 'NONE'); +#95417 = ORIENTED_EDGE ( 'NONE', *, *, #80120, .T. ) ; +#95418 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95420 = ADVANCED_FACE ( 'NONE', ( #13483 ), #44191, .T. ) ; +#95419 = CARTESIAN_POINT ( 'NONE', ( 1.515867623847370282, -1.051115598670280038, 0.8100000000000000533 ) ) ; +#95421 = ORIENTED_EDGE ( 'NONE', *, *, #20478, .T. ) ; +#95422 = PRESENTATION_STYLE_ASSIGNMENT (( #79653 ) ) ; +#95423 = CARTESIAN_POINT ( 'NONE', ( -0.1450079136436681071, -1.164927051866627927, 0.8100000000000000533 ) ) ; +#95424 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95425 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #72594 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51700, #20518, #52201 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95426 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1500000000000000222 ) ) ; +#95427 = STYLED_ITEM ( 'NONE', ( #51494 ), #73182 ) ; +#95428 = LINE ( 'NONE', #80165, #70944 ) ; +#95429 = FACE_OUTER_BOUND ( 'NONE', #50578, .T. ) ; +#95430 = AXIS2_PLACEMENT_3D ( 'NONE', #45882, #6553, #98460 ) ; +#95431 = EDGE_LOOP ( 'NONE', ( #85535, #42124, #6744, #49578 ) ) ; +#95432 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, -3.499999999999969802, 0.1829999999999999960 ) ) ; +#95433 = ORIENTED_EDGE ( 'NONE', *, *, #6443, .F. ) ; +#95434 = SURFACE_STYLE_FILL_AREA ( #3564 ) ; +#95435 = DIRECTION ( 'NONE', ( -0.3444045651374278427, 0.000000000000000000, -0.9388213331153585361 ) ) ; +#95436 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95437 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.149999999999999911, 0.000000000000000000 ) ) ; +#95438 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59218, #28529, #90820, #65835 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95439 = CARTESIAN_POINT ( 'NONE', ( 0.4675324675324660784, -1.070941558441560026, 0.8100000000000001643 ) ) ; +#95441 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95440 = VECTOR ( 'NONE', #74451, 1000.000000000000000 ) ; +#95442 = CARTESIAN_POINT ( 'NONE', ( 3.725242000000000164, 3.269274999999999931, 0.8991599999999999593 ) ) ; +#95443 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44918 ), #43283 ) ; +#95444 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95445 = EDGE_LOOP ( 'NONE', ( #41792, #16117, #28433, #11066 ) ) ; +#95446 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95447 = ORIENTED_EDGE ( 'NONE', *, *, #9990, .T. ) ; +#95448 = LINE ( 'NONE', #25560, #73509 ) ; +#95449 = AXIS2_PLACEMENT_3D ( 'NONE', #68038, #76721, #67535 ) ; +#95450 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95451 = ORIENTED_EDGE ( 'NONE', *, *, #78496, .T. ) ; +#95452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95453 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95454 = EDGE_CURVE ( 'NONE', #24973, #25439, #52892, .T. ) ; +#95455 = ADVANCED_FACE ( 'NONE', ( #51887 ), #90675, .T. ) ; +#95456 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#95457 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 0.1000000000000000056, -11.91999999999999993 ) ) ; +#95458 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8991599999999999593 ) ) ; +#95459 = CARTESIAN_POINT ( 'NONE', ( 8.144764000000000337, 11.70762200000000064, 0.8991599999999999593 ) ) ; +#95460 = FILL_AREA_STYLE ('',( #1573 ) ) ; +#95461 = VECTOR ( 'NONE', #100022, 1000.000000000000000 ) ; +#95463 = VERTEX_POINT ( 'NONE', #14519 ) ; +#95462 = ORIENTED_EDGE ( 'NONE', *, *, #86570, .F. ) ; +#95464 = FACE_OUTER_BOUND ( 'NONE', #94819, .T. ) ; +#95465 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8648700000000000276 ) ) ; +#95466 = ORIENTED_EDGE ( 'NONE', *, *, #43249, .F. ) ; +#95467 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95468 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95469 = CARTESIAN_POINT ( 'NONE', ( 6.954730999999999774, 10.37243899999999996, 0.8991599999999999593 ) ) ; +#95470 = VERTEX_POINT ( 'NONE', #6814 ) ; +#95471 = EDGE_CURVE ( 'NONE', #89439, #46497, #15538, .T. ) ; +#95472 = VERTEX_POINT ( 'NONE', #62068 ) ; +#95474 = AXIS2_PLACEMENT_3D ( 'NONE', #82720, #59281, #76543 ) ; +#95473 = FILL_AREA_STYLE_COLOUR ( '', #59611 ) ; +#95475 = PLANE ( 'NONE', #77357 ) ; +#95476 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97081 ), #13883 ) ; +#95477 = FILL_AREA_STYLE_COLOUR ( '', #12041 ) ; +#95478 = FILL_AREA_STYLE_COLOUR ( '', #99082 ) ; +#95480 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#95479 = SURFACE_SIDE_STYLE ('',( #26087 ) ) ; +#95481 = CARTESIAN_POINT ( 'NONE', ( -0.1150138248524561896, 0.2193344754160007348, 0.8100000000000000533 ) ) ; +#95482 = ORIENTED_EDGE ( 'NONE', *, *, #69095, .T. ) ; +#95483 = ORIENTED_EDGE ( 'NONE', *, *, #82923, .T. ) ; +#95484 = CARTESIAN_POINT ( 'NONE', ( 6.678958999999999868, 6.264147999999999605, 0.8991599999999999593 ) ) ; +#95485 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84072 ), #97084 ) ; +#95486 = ORIENTED_EDGE ( 'NONE', *, *, #35269, .T. ) ; +#95487 = FILL_AREA_STYLE ('',( #78674 ) ) ; +#95489 = ORIENTED_EDGE ( 'NONE', *, *, #68334, .T. ) ; +#95488 = CARTESIAN_POINT ( 'NONE', ( 10.77310700000000132, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#95490 = EDGE_CURVE ( 'NONE', #10232, #73519, #45673, .T. ) ; +#95491 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95492 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#95493 = ORIENTED_EDGE ( 'NONE', *, *, #3537, .F. ) ; +#95494 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95495 = EDGE_LOOP ( 'NONE', ( #20900, #35212, #38362, #36823 ) ) ; +#95496 = CARTESIAN_POINT ( 'NONE', ( -1.296446609406725958, 0.7099999999999999645, -1.049999999999999600 ) ) ; +#95497 = SURFACE_SIDE_STYLE ('',( #86359 ) ) ; +#95498 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -0.7666666666666686059, 0.000000000000000000 ) ) ; +#95499 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95500 = SURFACE_STYLE_FILL_AREA ( #64401 ) ; +#95501 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95502 = EDGE_CURVE ( 'NONE', #21301, #77078, #3488, .T. ) ; +#95504 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95503 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 1.149999999999999911, 0.000000000000000000 ) ) ; +#95505 = CARTESIAN_POINT ( 'NONE', ( 1.655510330387720330, -0.9679977428869780409, 0.8299999999999990719 ) ) ; +#95506 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95507 = ORIENTED_EDGE ( 'NONE', *, *, #100037, .T. ) ; +#95509 = EDGE_CURVE ( 'NONE', #70219, #74161, #8159, .T. ) ; +#95508 = CARTESIAN_POINT ( 'NONE', ( 1.578229014142010111, -1.479722134560319979, 0.8099999999999982769 ) ) ; +#95510 = EDGE_LOOP ( 'NONE', ( #50265, #71071, #26830, #41843, #66383, #47681 ) ) ; +#95511 = SURFACE_STYLE_FILL_AREA ( #93488 ) ; +#95512 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.000000000000000000 ) ) ; +#95513 = LINE ( 'NONE', #1631, #18594 ) ; +#95514 = STYLED_ITEM ( 'NONE', ( #29618 ), #54502 ) ; +#95516 = PRESENTATION_STYLE_ASSIGNMENT (( #10693 ) ) ; +#95515 = LINE ( 'NONE', #2136, #6991 ) ; +#95517 = PRESENTATION_STYLE_ASSIGNMENT (( #17419 ) ) ; +#95518 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95519 = AXIS2_PLACEMENT_3D ( 'NONE', #40151, #18642, #18123 ) ; +#95520 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95521 = STYLED_ITEM ( 'NONE', ( #77941 ), #78695 ) ; +#95522 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #61452 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #64348, #72497, #40375 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95523 = FACE_OUTER_BOUND ( 'NONE', #14188, .T. ) ; +#95524 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#95525 = VERTEX_POINT ( 'NONE', #751 ) ; +#95526 = ADVANCED_FACE ( 'NONE', ( #38060 ), #38559, .F. ) ; +#95528 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95527 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95530 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#95529 = PLANE ( 'NONE', #203 ) ; +#95531 = STYLED_ITEM ( 'NONE', ( #53121 ), #61766 ) ; +#95532 = CARTESIAN_POINT ( 'NONE', ( 14.00000000000000000, 1.399999999999999911, 0.000000000000000000 ) ) ; +#95533 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70025, 'distance_accuracy_value', 'NONE'); +#95534 = VERTEX_POINT ( 'NONE', #30359 ) ; +#95535 = ADVANCED_FACE ( 'NONE', ( #86534 ), #23751, .T. ) ; +#95536 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95537 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95538 = PRESENTATION_STYLE_ASSIGNMENT (( #72102 ) ) ; +#95539 = VECTOR ( 'NONE', #29157, 1000.000000000000000 ) ; +#95540 = PLANE ( 'NONE', #45281 ) ; +#95541 = LINE ( 'NONE', #56812, #51846 ) ; +#95542 = EDGE_CURVE ( 'NONE', #8017, #84497, #2291, .T. ) ; +#95543 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999988787, -3.149999999999979927, 0.000000000000000000 ) ) ; +#95544 = LINE ( 'NONE', #75609, #90395 ) ; +#95545 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95546 = PRESENTATION_STYLE_ASSIGNMENT (( #25170 ) ) ; +#95547 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.5000000000000000000, -0.02000000000000000042 ) ) ; +#95548 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95549 = EDGE_LOOP ( 'NONE', ( #50370, #44636, #55308 ) ) ; +#95550 = SURFACE_SIDE_STYLE ('',( #1671 ) ) ; +#95551 = ADVANCED_FACE ( 'NONE', ( #49770 ), #48252, .T. ) ; +#95552 = EDGE_LOOP ( 'NONE', ( #78744, #16856, #95838, #82344 ) ) ; +#95553 = VECTOR ( 'NONE', #81504, 1000.000000000000000 ) ; +#95554 = SURFACE_STYLE_FILL_AREA ( #49145 ) ; +#95555 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #21933, 'distance_accuracy_value', 'NONE'); +#95556 = PRESENTATION_STYLE_ASSIGNMENT (( #80799 ) ) ; +#95557 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95558 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.1238200612200849871, 0.000000000000000000 ) ) ; +#95559 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53183 ), #89043 ) ; +#95560 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95561 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95562 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#95563 = ORIENTED_EDGE ( 'NONE', *, *, #23473, .T. ) ; +#95564 = CARTESIAN_POINT ( 'NONE', ( 4.798054999999999737, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#95565 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#95566 = ORIENTED_EDGE ( 'NONE', *, *, #14438, .T. ) ; +#95567 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95568 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95569 = ORIENTED_EDGE ( 'NONE', *, *, #2835, .F. ) ; +#95570 = EDGE_CURVE ( 'NONE', #70624, #2949, #10852, .T. ) ; +#95571 = EDGE_CURVE ( 'NONE', #61851, #20053, #73246, .T. ) ; +#95572 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95573 = FILL_AREA_STYLE ('',( #63972 ) ) ; +#95574 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95575 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95576 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 7.388448000000000349, 0.8991599999999999593 ) ) ; +#95577 = CARTESIAN_POINT ( 'NONE', ( 1.700000000000000178, -3.266666666666647068, 0.000000000000000000 ) ) ; +#95578 = ORIENTED_EDGE ( 'NONE', *, *, #52647, .T. ) ; +#95579 = EDGE_LOOP ( 'NONE', ( #41773, #80509, #8822, #79467 ) ) ; +#95580 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95581 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95582 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95583 = ADVANCED_FACE ( 'NONE', ( #50286 ), #48757, .T. ) ; +#95584 = CIRCLE ( 'NONE', #41848, 0.2000000000000005107 ) ; +#95585 = EDGE_LOOP ( 'NONE', ( #30095, #19528, #44314, #43269, #68129 ) ) ; +#95586 = EDGE_CURVE ( 'NONE', #81364, #77676, #50781, .T. ) ; +#95587 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95588 = PLANE ( 'NONE', #8929 ) ; +#95589 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.60762199999999922, 0.8991599999999999593 ) ) ; +#95590 = CARTESIAN_POINT ( 'NONE', ( -0.4458598713506949918, -1.104165518103240151, 0.8299999999999999600 ) ) ; +#95591 = SURFACE_STYLE_USAGE ( .BOTH. , #25222 ) ; +#95592 = VECTOR ( 'NONE', #94334, 1000.000000000000000 ) ; +#95593 = ORIENTED_EDGE ( 'NONE', *, *, #82277, .F. ) ; +#95594 = EDGE_CURVE ( 'NONE', #9763, #46504, #98134, .T. ) ; +#95596 = VERTEX_POINT ( 'NONE', #52271 ) ; +#95595 = VERTEX_POINT ( 'NONE', #60445 ) ; +#95597 = CARTESIAN_POINT ( 'NONE', ( 5.130395124874956636, 4.135756875125044196, 0.8648700000000000276 ) ) ; +#95598 = PRODUCT ( 'L0201_20210301.xtd', 'L0201_20210301.xtd', '', ( #34123 ) ) ; +#95599 = ORIENTED_EDGE ( 'NONE', *, *, #87416, .F. ) ; +#95600 = LINE ( 'NONE', #4214, #83408 ) ; +#95601 = STYLED_ITEM ( 'NONE', ( #91279 ), #61895 ) ; +#95602 = ORIENTED_EDGE ( 'NONE', *, *, #22508, .T. ) ; +#95604 = VERTEX_POINT ( 'NONE', #58453 ) ; +#95603 = LINE ( 'NONE', #25709, #85155 ) ; +#95605 = ADVANCED_FACE ( 'NONE', ( #11845 ), #59949, .T. ) ; +#95607 = FILL_AREA_STYLE ('',( #22675 ) ) ; +#95606 = SURFACE_STYLE_USAGE ( .BOTH. , #17006 ) ; +#95608 = PRESENTATION_STYLE_ASSIGNMENT (( #83955 ) ) ; +#95609 = EDGE_LOOP ( 'NONE', ( #11865, #29591, #18130, #98686 ) ) ; +#95610 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95611 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95612 = DIRECTION ( 'NONE', ( -0.7071067811865479058, -0.7071067811865472397, 0.000000000000000000 ) ) ; +#95613 = ORIENTED_EDGE ( 'NONE', *, *, #59002, .T. ) ; +#95614 = VECTOR ( 'NONE', #70271, 1000.000000000000000 ) ; +#95615 = ADVANCED_FACE ( 'NONE', ( #91546 ), #35459, .T. ) ; +#95616 = LINE ( 'NONE', #72670, #10442 ) ; +#95617 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95618 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#95619 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.499999999999969802, 0.1829999999999999960 ) ) ; +#95620 = ORIENTED_EDGE ( 'NONE', *, *, #32570, .T. ) ; +#95621 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#95622 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#95623 = AXIS2_PLACEMENT_3D ( 'NONE', #99562, #15361, #92476 ) ; +#95624 = EDGE_CURVE ( 'NONE', #80711, #75525, #82900, .T. ) ; +#95626 = SURFACE_SIDE_STYLE ('',( #80358 ) ) ; +#95625 = LINE ( 'NONE', #66521, #31673 ) ; +#95627 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#95628 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#95629 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95630 = PRESENTATION_STYLE_ASSIGNMENT (( #9305 ) ) ; +#95631 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #67161, #5838, #51372, #97760 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95632 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95633 = CARTESIAN_POINT ( 'NONE', ( 4.387933000000000305, 3.958979999999999944, 0.8991599999999999593 ) ) ; +#95634 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95635 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999995115, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#95636 = FILL_AREA_STYLE_COLOUR ( '', #23579 ) ; +#95637 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95638 = CYLINDRICAL_SURFACE ( 'NONE', #65416, 0.05000000000000012768 ) ; +#95639 = VECTOR ( 'NONE', #22852, 1000.000000000000000 ) ; +#95640 = ORIENTED_EDGE ( 'NONE', *, *, #24188, .F. ) ; +#95641 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #77889, #39093, #30917, #77369 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95642 = SURFACE_STYLE_FILL_AREA ( #82386 ) ; +#95643 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95644 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -0.9000000000000003553, 0.000000000000000000 ) ) ; +#95645 = ORIENTED_EDGE ( 'NONE', *, *, #100129, .F. ) ; +#95646 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95647 = EDGE_CURVE ( 'NONE', #27723, #76102, #12864, .T. ) ; +#95649 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95648 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#95650 = CARTESIAN_POINT ( 'NONE', ( 1.588352962588889916, -1.042364979248350032, 0.8100000000000000533 ) ) ; +#95651 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #7685, 'distance_accuracy_value', 'NONE'); +#95652 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.4245906043549200204, -0.02000000000000000042 ) ) ; +#95653 = CARTESIAN_POINT ( 'NONE', ( 0.2365201132049190025, -1.424034756619420028, 0.8100000000000000533 ) ) ; +#95654 = VECTOR ( 'NONE', #41100, 1000.000000000000000 ) ; +#95655 = STYLED_ITEM ( 'NONE', ( #60195 ), #90733 ) ; +#95656 = DIRECTION ( 'NONE', ( -1.401985567973789257E-16, 1.000000000000000000, -2.620751377075717173E-32 ) ) ; +#95657 = FILL_AREA_STYLE_COLOUR ( '', #67201 ) ; +#95658 = EDGE_LOOP ( 'NONE', ( #73532, #12295, #12542, #59189 ) ) ; +#95659 = EDGE_CURVE ( 'NONE', #76926, #22947, #36440, .T. ) ; +#95660 = SURFACE_STYLE_FILL_AREA ( #64555 ) ; +#95661 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95662 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#95663 = VECTOR ( 'NONE', #36658, 1000.000000000000000 ) ; +#95664 = PLANE ( 'NONE', #41639 ) ; +#95665 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#95666 = PLANE ( 'NONE', #74632 ) ; +#95667 = LINE ( 'NONE', #25771, #1236 ) ; +#95668 = CARTESIAN_POINT ( 'NONE', ( 10.36298549949982295, 4.857005499499825518, 0.8991599999999999593 ) ) ; +#95669 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#95670 = ADVANCED_FACE ( 'NONE', ( #62443 ), #85894, .T. ) ; +#95671 = FILL_AREA_STYLE ('',( #31907 ) ) ; +#95672 = STYLED_ITEM ( 'NONE', ( #73924 ), #17004 ) ; +#95673 = SURFACE_STYLE_USAGE ( .BOTH. , #40597 ) ; +#95674 = STYLED_ITEM ( 'NONE', ( #75839 ), #62293 ) ; +#95675 = ORIENTED_EDGE ( 'NONE', *, *, #83620, .F. ) ; +#95676 = FILL_AREA_STYLE_COLOUR ( '', #64385 ) ; +#95677 = EDGE_CURVE ( 'NONE', #88616, #34605, #22609, .T. ) ; +#95678 = ORIENTED_EDGE ( 'NONE', *, *, #9990, .F. ) ; +#95679 = FILL_AREA_STYLE ('',( #4292 ) ) ; +#95681 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100109 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56046, #87166, #64196 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95680 = SURFACE_SIDE_STYLE ('',( #25791 ) ) ; +#95682 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95683 = CARTESIAN_POINT ( 'NONE', ( 1.877922077922079991, -1.064001623376620076, 0.8299999999999999600 ) ) ; +#95684 = EDGE_LOOP ( 'NONE', ( #1125, #4301, #6263, #23601 ) ) ; +#95685 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#95686 = LINE ( 'NONE', #88075, #86122 ) ; +#95687 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28803 ) ) ; +#95688 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #2532 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #25794, #96198, #89077 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95689 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.1200000000000000094, -0.6500000000000001332 ) ) ; +#95690 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95691 = ORIENTED_EDGE ( 'NONE', *, *, #53461, .F. ) ; +#95692 = LINE ( 'NONE', #9866, #82049 ) ; +#95693 = EDGE_CURVE ( 'NONE', #61165, #81105, #45535, .T. ) ; +#95694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95695 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#95696 = FILL_AREA_STYLE ('',( #49281 ) ) ; +#95697 = PRESENTATION_STYLE_ASSIGNMENT (( #55948 ) ) ; +#95698 = FILL_AREA_STYLE_COLOUR ( '', #76773 ) ; +#95699 = ORIENTED_EDGE ( 'NONE', *, *, #29523, .T. ) ; +#95700 = CYLINDRICAL_SURFACE ( 'NONE', #100174, 0.05000000000000012768 ) ; +#95701 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14127 ) ) ; +#95702 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #75408, 'distance_accuracy_value', 'NONE'); +#95703 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95704 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95705 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95706 = EDGE_LOOP ( 'NONE', ( #40775, #65591, #69533, #32367 ) ) ; +#95707 = ADVANCED_FACE ( 'NONE', ( #61938 ), #23128, .F. ) ; +#95708 = LINE ( 'NONE', #49293, #100145 ) ; +#95709 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95711 = SURFACE_SIDE_STYLE ('',( #2828 ) ) ; +#95712 = VECTOR ( 'NONE', #95146, 1000.000000000000000 ) ; +#95713 = LINE ( 'NONE', #93679, #15750 ) ; +#95714 = EDGE_CURVE ( 'NONE', #27451, #47921, #76726, .T. ) ; +#95715 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753241173, 0.6899999999999999467, 0.2077922077922080002 ) ) ; +#95716 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20304, #6439, #66766, #51495 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95717 = STYLED_ITEM ( 'NONE', ( #29502 ), #30696 ) ; +#95718 = ORIENTED_EDGE ( 'NONE', *, *, #27106, .T. ) ; +#95720 = VERTEX_POINT ( 'NONE', #6696 ) ; +#95719 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95721 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43556 ), #51756 ) ; +#95722 = CIRCLE ( 'NONE', #30484, 0.009999999999999998473 ) ; +#95723 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #65579, 'distance_accuracy_value', 'NONE'); +#95724 = SURFACE_SIDE_STYLE ('',( #11412 ) ) ; +#95725 = FILL_AREA_STYLE_COLOUR ( '', #36177 ) ; +#95726 = ORIENTED_EDGE ( 'NONE', *, *, #97919, .T. ) ; +#95727 = STYLED_ITEM ( 'NONE', ( #27283 ), #55169 ) ; +#95728 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#95729 = CARTESIAN_POINT ( 'NONE', ( 12.68106399999999923, 6.652400000000000091, 0.8991599999999999593 ) ) ; +#95730 = LINE ( 'NONE', #25847, #40104 ) ; +#95731 = EDGE_LOOP ( 'NONE', ( #40655, #47484, #49537, #15072 ) ) ; +#95732 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #35979 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62658, #39654, #94251 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95733 = PLANE ( 'NONE', #48823 ) ; +#95734 = ORIENTED_EDGE ( 'NONE', *, *, #48932, .F. ) ; +#95735 = ORIENTED_EDGE ( 'NONE', *, *, #60672, .T. ) ; +#95736 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29050 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #97365, #58637, #59653 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95738 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95737 = FILL_AREA_STYLE ('',( #72286 ) ) ; +#95739 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #61547 ) ) ; +#95741 = EDGE_CURVE ( 'NONE', #53981, #53924, #61441, .T. ) ; +#95740 = CYLINDRICAL_SURFACE ( 'NONE', #81704, 0.009999999999999998473 ) ; +#95742 = VERTEX_POINT ( 'NONE', #54268 ) ; +#95743 = SURFACE_SIDE_STYLE ('',( #9915 ) ) ; +#95744 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #82744 ), #12545 ) ; +#95745 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72978 ) ) ; +#95746 = ORIENTED_EDGE ( 'NONE', *, *, #296, .F. ) ; +#95747 = STYLED_ITEM ( 'NONE', ( #7481 ), #23300 ) ; +#95748 = FACE_OUTER_BOUND ( 'NONE', #87922, .T. ) ; +#95749 = ORIENTED_EDGE ( 'NONE', *, *, #70264, .F. ) ; +#95750 = EDGE_CURVE ( 'NONE', #97408, #2820, #15421, .T. ) ; +#95752 = EDGE_LOOP ( 'NONE', ( #67361, #23946, #66589, #34111 ) ) ; +#95751 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #53072, #98433, #60739, #38249 ), + ( #13683, #68846, #67372, #99424 ), + ( #85188, #30059, #99906, #28572 ), + ( #61254, #75536, #92347, #36744 ) ), + .UNSPECIFIED., .F., .F., .T. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243653816, 0.8047378541243653816, 1.000000000000000000), + ( 0.8047378541243652705, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243652705), + ( 0.8047378541243652705, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243652705), + ( 1.000000000000000000, 0.8047378541243653816, 0.8047378541243653816, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#95753 = PRESENTATION_STYLE_ASSIGNMENT (( #26365 ) ) ; +#95754 = CLOSED_SHELL ( 'NONE', ( #89150, #56544, #22133, #52753, #29141, #95583 ) ) ; +#95756 = LINE ( 'NONE', #48843, #96293 ) ; +#95755 = SURFACE_SIDE_STYLE ('',( #18142 ) ) ; +#95757 = CARTESIAN_POINT ( 'NONE', ( -1.049523990565160103, -1.254158608853950030, 0.8100000000000000533 ) ) ; +#95758 = CARTESIAN_POINT ( 'NONE', ( -0.4958578643762691085, 0.4808578643762690952, -0.2500000000000000000 ) ) ; +#95759 = STYLED_ITEM ( 'NONE', ( #74635 ), #100345 ) ; +#95760 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95761 = VECTOR ( 'NONE', #61412, 1000.000000000000000 ) ; +#95762 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95763 = PRESENTATION_STYLE_ASSIGNMENT (( #17162 ) ) ; +#95764 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95765 = VERTEX_POINT ( 'NONE', #19346 ) ; +#95766 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95767 = LINE ( 'NONE', #80496, #77372 ) ; +#95768 = ADVANCED_FACE ( 'NONE', ( #65829 ), #1131, .T. ) ; +#95769 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95770 = LINE ( 'NONE', #17170, #57988 ) ; +#95771 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #49809, 'distance_accuracy_value', 'NONE'); +#95772 = CARTESIAN_POINT ( 'NONE', ( 4.126304000000000194, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#95773 = STYLED_ITEM ( 'NONE', ( #11856 ), #43732 ) ; +#95774 = LINE ( 'NONE', #1885, #56101 ) ; +#95775 = FILL_AREA_STYLE ('',( #70302 ) ) ; +#95776 = CARTESIAN_POINT ( 'NONE', ( 5.802146999999999721, 9.983529000000000764, 0.8991599999999999593 ) ) ; +#95777 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95778 = ORIENTED_EDGE ( 'NONE', *, *, #69, .T. ) ; +#95779 = EDGE_CURVE ( 'NONE', #17076, #68435, #88313, .T. ) ; +#95780 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95781 = FACE_OUTER_BOUND ( 'NONE', #5310, .T. ) ; +#95782 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95783 = PLANE ( 'NONE', #64186 ) ; +#95784 = FACE_OUTER_BOUND ( 'NONE', #52616, .T. ) ; +#95785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2909 ) ) ; +#95786 = CARTESIAN_POINT ( 'NONE', ( 0.4623821970225030498, -1.113520705134940059, 0.8300000000000015143 ) ) ; +#95787 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86046 ) ) ; +#95788 = LINE ( 'NONE', #96794, #13746 ) ; +#95789 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#95790 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95791 = CARTESIAN_POINT ( 'NONE', ( -0.8499999999999999778, 0.2500000000000000000, -0.8499999999999999778 ) ) ; +#95792 = PRESENTATION_STYLE_ASSIGNMENT (( #48879 ) ) ; +#95793 = FILL_AREA_STYLE_COLOUR ( '', #62212 ) ; +#95794 = STYLED_ITEM ( 'NONE', ( #53364 ), #31003 ) ; +#95795 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.266666666666653285, 0.000000000000000000 ) ) ; +#95796 = CARTESIAN_POINT ( 'NONE', ( 0.09999999999999634182, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#95797 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95798 = PLANE ( 'NONE', #16010 ) ; +#95799 = ADVANCED_FACE ( 'NONE', ( #34208 ), #81672, .F. ) ; +#95800 = CARTESIAN_POINT ( 'NONE', ( 1.901254715655619876, -1.325441991778449680, 0.8100000000000004974 ) ) ; +#95801 = FILL_AREA_STYLE ('',( #97786 ) ) ; +#95802 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95803 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#95805 = EDGE_CURVE ( 'NONE', #29477, #4688, #11606, .T. ) ; +#95804 = FACE_OUTER_BOUND ( 'NONE', #67310, .T. ) ; +#95806 = PRESENTATION_STYLE_ASSIGNMENT (( #66209 ) ) ; +#95807 = EDGE_LOOP ( 'NONE', ( #88275, #27358, #82088, #19376 ) ) ; +#95809 = VECTOR ( 'NONE', #21357, 1000.000000000000000 ) ; +#95808 = LINE ( 'NONE', #25919, #50335 ) ; +#95810 = CARTESIAN_POINT ( 'NONE', ( 1.979999999999999982, 1.600000000000000089, -11.41999999999999993 ) ) ; +#95811 = SURFACE_STYLE_FILL_AREA ( #3915 ) ; +#95814 = CARTESIAN_POINT ( 'NONE', ( -0.4406630133853430276, 0.3469465759269649840, 0.8100000000000000533 ) ) ; +#95813 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#95812 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64796 ), #61680 ) ; +#95815 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95816 = ADVANCED_FACE ( 'NONE', ( #3031 ), #65311, .T. ) ; +#95817 = EDGE_CURVE ( 'NONE', #58753, #38354, #11774, .T. ) ; +#95818 = STYLED_ITEM ( 'NONE', ( #41923 ), #17421 ) ; +#95819 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#95820 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#95821 = ORIENTED_EDGE ( 'NONE', *, *, #29681, .F. ) ; +#95822 = VECTOR ( 'NONE', #16175, 1000.000000000000000 ) ; +#95823 = FILL_AREA_STYLE ('',( #73887 ) ) ; +#95824 = SURFACE_STYLE_FILL_AREA ( #4417 ) ; +#95825 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95826 = EDGE_CURVE ( 'NONE', #312, #83312, #6889, .T. ) ; +#95827 = EDGE_CURVE ( 'NONE', #79328, #29731, #53022, .T. ) ; +#95828 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55584 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70997, #78643, #31686 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95829 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95830 = VECTOR ( 'NONE', #97810, 1000.000000000000000 ) ; +#95831 = CLOSED_SHELL ( 'NONE', ( #97105, #97044, #55780, #17553, #21200, #21872, #86823, #55437, #39376, #33287, #97542, #8139, #2033, #58497, #11929, #80364, #85871, #64634, #80598, #86492, #18917, #11091, #31322, #88909, #53245, #68797, #4114, #80521, #14130, #51339, #40571, #63298, #12723, #66103, #9467, #75386, #7699, #15783, #53396, #72371, #89291, #57083, #88612, #87516, #75562, #88698, #17785, #30508, #76344, #53563, #72665, #8388, #73798, #96943, #26353, #83492, #30716, #803, #81290, #18786, #64617, #19413, #32588, #88504, #35227, #7104, #46374, #30272, #59920 ) ) ; +#95832 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95833 = ORIENTED_EDGE ( 'NONE', *, *, #73765, .T. ) ; +#95834 = ORIENTED_EDGE ( 'NONE', *, *, #42137, .T. ) ; +#95835 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72992 ), #32249 ) ; +#95836 = EDGE_CURVE ( 'NONE', #31406, #29659, #61199, .T. ) ; +#95837 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#95838 = ORIENTED_EDGE ( 'NONE', *, *, #43865, .T. ) ; +#95839 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#95840 = STYLED_ITEM ( 'NONE', ( #4130 ), #50464 ) ; +#95841 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95842 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#95843 = PLANE ( 'NONE', #100165 ) ; +#95844 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#95845 = EDGE_CURVE ( 'NONE', #92811, #20528, #14151, .T. ) ; +#95846 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #31915 ) ; +#95847 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.836970198721029688E-16, -1.000000000000000000 ) ) ; +#95848 = SURFACE_STYLE_USAGE ( .BOTH. , #11016 ) ; +#95849 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48601 ) ) ; +#95851 = ORIENTED_EDGE ( 'NONE', *, *, #96146, .T. ) ; +#95850 = VERTEX_POINT ( 'NONE', #6953 ) ; +#95852 = ORIENTED_EDGE ( 'NONE', *, *, #76838, .F. ) ; +#95853 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999989786, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#95854 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71520, 'distance_accuracy_value', 'NONE'); +#95856 = CARTESIAN_POINT ( 'NONE', ( 1.417810389965429962, -1.053930089500670020, 0.8299999999999999600 ) ) ; +#95855 = PLANE ( 'NONE', #19625 ) ; +#95857 = ORIENTED_EDGE ( 'NONE', *, *, #58189, .T. ) ; +#95858 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #75127, .NOT_KNOWN. ) ; +#95859 = ORIENTED_EDGE ( 'NONE', *, *, #14293, .T. ) ; +#95860 = SURFACE_STYLE_FILL_AREA ( #95347 ) ; +#95862 = VERTEX_POINT ( 'NONE', #69279 ) ; +#95861 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2973 ) ) ; +#95864 = FILL_AREA_STYLE_COLOUR ( '', #69011 ) ; +#95863 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#95865 = ORIENTED_EDGE ( 'NONE', *, *, #17167, .F. ) ; +#95866 = VERTEX_POINT ( 'NONE', #100350 ) ; +#95868 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95867 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.099999999999980549, -0.02000000000000000042 ) ) ; +#95869 = LINE ( 'NONE', #9037, #19507 ) ; +#95870 = EDGE_CURVE ( 'NONE', #35120, #21904, #28521, .T. ) ; +#95872 = ORIENTED_EDGE ( 'NONE', *, *, #58920, .T. ) ; +#95871 = FILL_AREA_STYLE_COLOUR ( '', #86932 ) ; +#95873 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14363 ) ) ; +#95874 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#95875 = VERTEX_POINT ( 'NONE', #98878 ) ; +#95876 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46984 ), #14286 ) ; +#95877 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76354 ) ) ; +#95878 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95879 = ORIENTED_EDGE ( 'NONE', *, *, #94556, .F. ) ; +#95880 = LINE ( 'NONE', #79599, #23767 ) ; +#95881 = CARTESIAN_POINT ( 'NONE', ( -0.01004137219608649927, -1.188470249711290228, 0.8299999999999999600 ) ) ; +#95882 = VERTEX_POINT ( 'NONE', #52026 ) ; +#95883 = EDGE_CURVE ( 'NONE', #53705, #74561, #83156, .T. ) ; +#95884 = ORIENTED_EDGE ( 'NONE', *, *, #54012, .F. ) ; +#95886 = CARTESIAN_POINT ( 'NONE', ( 1.325735931288071212, 0.6599999999999998090, 1.099999999999999867 ) ) ; +#95885 = SURFACE_STYLE_USAGE ( .BOTH. , #94867 ) ; +#95887 = VECTOR ( 'NONE', #24926, 1000.000000000000000 ) ; +#95888 = PRESENTATION_STYLE_ASSIGNMENT (( #43792 ) ) ; +#95889 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95890 = STYLED_ITEM ( 'NONE', ( #98103 ), #79587 ) ; +#95891 = CARTESIAN_POINT ( 'NONE', ( -1.219009570153848143, -1.136068795193200476, 0.8099999999998879208 ) ) ; +#95892 = LINE ( 'NONE', #57145, #10203 ) ; +#95893 = LINE ( 'NONE', #33137, #9620 ) ; +#95895 = VECTOR ( 'NONE', #43147, 1000.000000000000000 ) ; +#95894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43815, 'distance_accuracy_value', 'NONE'); +#95896 = ORIENTED_EDGE ( 'NONE', *, *, #48920, .T. ) ; +#95897 = STYLED_ITEM ( 'NONE', ( #16058 ), #63022 ) ; +#95898 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95899 = EDGE_LOOP ( 'NONE', ( #60613, #22652, #50208, #50000 ) ) ; +#95900 = SURFACE_STYLE_USAGE ( .BOTH. , #64781 ) ; +#95901 = FILL_AREA_STYLE ('',( #3520 ) ) ; +#95902 = FILL_AREA_STYLE ('',( #17801 ) ) ; +#95903 = VECTOR ( 'NONE', #98663, 1000.000000000000000 ) ; +#95904 = SURFACE_STYLE_USAGE ( .BOTH. , #66786 ) ; +#95905 = CLOSED_SHELL ( 'NONE', ( #86259, #19016, #37410, #56927, #49626, #61845 ) ) ; +#95906 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95907 = EDGE_CURVE ( 'NONE', #89321, #35471, #44317, .T. ) ; +#95908 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38868 ), #51933 ) ; +#95909 = CARTESIAN_POINT ( 'NONE', ( 4.832300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#95910 = SURFACE_SIDE_STYLE ('',( #64792 ) ) ; +#95911 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95912 = CARTESIAN_POINT ( 'NONE', ( 10.64582799999999985, 5.139847999999999750, 0.8991599999999999593 ) ) ; +#95913 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#95914 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#95915 = SURFACE_STYLE_USAGE ( .BOTH. , #73486 ) ; +#95916 = PLANE ( 'NONE', #34237 ) ; +#95917 = CARTESIAN_POINT ( 'NONE', ( 0.6316964285714280480, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#95918 = PLANE ( 'NONE', #35950 ) ; +#95919 = CYLINDRICAL_SURFACE ( 'NONE', #43849, 0.05000000000000002359 ) ; +#95920 = FILL_AREA_STYLE ('',( #25523 ) ) ; +#95921 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95922 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95923 = EDGE_LOOP ( 'NONE', ( #65457, #56860, #8936, #48453 ) ) ; +#95924 = CARTESIAN_POINT ( 'NONE', ( 1.617430281440370043, -0.9137302873894740385, 0.8100000000000000533 ) ) ; +#95925 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61052, 'distance_accuracy_value', 'NONE'); +#95926 = ORIENTED_EDGE ( 'NONE', *, *, #49074, .F. ) ; +#95928 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58617, 'distance_accuracy_value', 'NONE'); +#95927 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999929778, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#95929 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, -3.149999999999999911, 0.000000000000000000 ) ) ; +#95930 = SURFACE_SIDE_STYLE ('',( #33177 ) ) ; +#95931 = LINE ( 'NONE', #10088, #63211 ) ; +#95932 = FILL_AREA_STYLE ('',( #4890 ) ) ; +#95933 = LINE ( 'NONE', #76573, #38577 ) ; +#95934 = STYLED_ITEM ( 'NONE', ( #62205 ), #32232 ) ; +#95935 = AXIS2_PLACEMENT_3D ( 'NONE', #48451, #86207, #64749 ) ; +#95936 = CARTESIAN_POINT ( 'NONE', ( 1.762090253802699680, -0.9814610950457449690, 0.8100000000000006084 ) ) ; +#95937 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95938 = ORIENTED_EDGE ( 'NONE', *, *, #4100, .F. ) ; +#95939 = ORIENTED_EDGE ( 'NONE', *, *, #11820, .T. ) ; +#95940 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80172, 'distance_accuracy_value', 'NONE'); +#95941 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -0.3666666666666686392, 0.000000000000000000 ) ) ; +#95942 = FACE_BOUND ( 'NONE', #86089, .T. ) ; +#95943 = LINE ( 'NONE', #57718, #10689 ) ; +#95944 = EDGE_CURVE ( 'NONE', #71148, #23470, #29024, .T. ) ; +#95945 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #38908 ), #81365 ) ; +#95946 = STYLED_ITEM ( 'NONE', ( #91429 ), #91582 ) ; +#95947 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#95948 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95949 = CARTESIAN_POINT ( 'NONE', ( 8.559863124875013440, 2.134644875124987795, 0.8648700000000000276 ) ) ; +#95950 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95951 = EDGE_LOOP ( 'NONE', ( #70917, #96119, #12848, #25373, #71495, #68021 ) ) ; +#95953 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#95952 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#95954 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #4717 ) ) ; +#95955 = ORIENTED_EDGE ( 'NONE', *, *, #88813, .F. ) ; +#95956 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#95957 = ORIENTED_EDGE ( 'NONE', *, *, #30810, .F. ) ; +#95958 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #71931, #23444, #33642, #63283 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#95959 = FILL_AREA_STYLE_COLOUR ( '', #75113 ) ; +#95960 = LINE ( 'NONE', #64850, #66483 ) ; +#95961 = FILL_AREA_STYLE_COLOUR ( '', #45011 ) ; +#95962 = FACE_OUTER_BOUND ( 'NONE', #100753, .T. ) ; +#95963 = EDGE_CURVE ( 'NONE', #80304, #13861, #52515, .T. ) ; +#95964 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #32376 ) ) ; +#95965 = CARTESIAN_POINT ( 'NONE', ( 11.54988799999999927, 11.40739400000000003, 0.8991599999999999593 ) ) ; +#95966 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#95967 = PRESENTATION_STYLE_ASSIGNMENT (( #71511 ) ) ; +#95968 = VECTOR ( 'NONE', #48264, 1000.000000000000000 ) ; +#95970 = ORIENTED_EDGE ( 'NONE', *, *, #72565, .T. ) ; +#95969 = ORIENTED_EDGE ( 'NONE', *, *, #61542, .T. ) ; +#95971 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95972 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999833, 0.000000000000000000, -0.1499999999999999667 ) ) ; +#95973 = EDGE_LOOP ( 'NONE', ( #8866, #50789, #77401, #46485 ) ) ; +#95974 = SURFACE_SIDE_STYLE ('',( #49059 ) ) ; +#95976 = CARTESIAN_POINT ( 'NONE', ( 1.000000000000000000, 4.724230266243499888E-17, 0.2499999999999999445 ) ) ; +#95975 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999659677 ) ) ; +#95977 = AXIS2_PLACEMENT_3D ( 'NONE', #23328, #7403, #89013 ) ; +#95978 = ORIENTED_EDGE ( 'NONE', *, *, #91953, .F. ) ; +#95979 = EDGE_LOOP ( 'NONE', ( #93334, #36155, #66758, #77541 ) ) ; +#95980 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#95981 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#95982 = CARTESIAN_POINT ( 'NONE', ( 7.661838000000000370, 2.155857000000000134, 0.8648700000000000276 ) ) ; +#95983 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#95984 = ORIENTED_EDGE ( 'NONE', *, *, #58313, .F. ) ; +#95985 = ORIENTED_EDGE ( 'NONE', *, *, #11353, .T. ) ; +#95986 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#95987 = ORIENTED_EDGE ( 'NONE', *, *, #16275, .T. ) ; +#95988 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6496 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5867, #53388, #61576 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#95989 = ADVANCED_FACE ( 'NONE', ( #75985 ), #26032, .T. ) ; +#95992 = ORIENTED_EDGE ( 'NONE', *, *, #31867, .F. ) ; +#95991 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#95990 = SURFACE_STYLE_FILL_AREA ( #17390 ) ; +#95993 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#95994 = PRESENTATION_STYLE_ASSIGNMENT (( #80728 ) ) ; +#95995 = ORIENTED_EDGE ( 'NONE', *, *, #43066, .T. ) ; +#95996 = CARTESIAN_POINT ( 'NONE', ( -0.01972870844762369957, -1.247965265924660061, 0.8100000000000000533 ) ) ; +#95997 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2600000000000000089, -0.1350000000000000089 ) ) ; +#95998 = ORIENTED_EDGE ( 'NONE', *, *, #43758, .T. ) ; +#95999 = EDGE_CURVE ( 'NONE', #21443, #17385, #62701, .T. ) ; +#96000 = CARTESIAN_POINT ( 'NONE', ( 0.1302369866146559918, 0.3100465759269659949, 0.8100000000000000533 ) ) ; +#96001 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75824, #4859, #76314, #29848 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96002 = FILL_AREA_STYLE_COLOUR ( '', #28961 ) ; +#96003 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96004 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96005 = CARTESIAN_POINT ( 'NONE', ( -1.063525042275559995, -1.248384608377719918, 0.8300000000000000711 ) ) ; +#96006 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.325331135337491605E-12, 0.000000000000000000 ) ) ; +#96007 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96008 = AXIS2_PLACEMENT_3D ( 'NONE', #24433, #8995, #93296 ) ; +#96010 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333323090, -0.1000000000000000056, 0.000000000000000000 ) ) ; +#96009 = LINE ( 'NONE', #70533, #69221 ) ; +#96011 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70001 ), #84504 ) ; +#96012 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96013 = ORIENTED_EDGE ( 'NONE', *, *, #42380, .F. ) ; +#96014 = FILL_AREA_STYLE_COLOUR ( '', #41415 ) ; +#96015 = VERTEX_POINT ( 'NONE', #69815 ) ; +#96016 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#96017 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96018 = FILL_AREA_STYLE_COLOUR ( '', #43418 ) ; +#96019 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96020 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#96021 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96023 = CARTESIAN_POINT ( 'NONE', ( 0.01172780041795889495, -1.365463486801246074, 0.8099999999997000710 ) ) ; +#96022 = VECTOR ( 'NONE', #88182, 1000.000000000000000 ) ; +#96024 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96025 = FILL_AREA_STYLE ('',( #88908 ) ) ; +#96026 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#96027 = EDGE_CURVE ( 'NONE', #53594, #44243, #93276, .T. ) ; +#96028 = FILL_AREA_STYLE_COLOUR ( '', #41112 ) ; +#96029 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.01000000000000000021, -0.1250000000000000000 ) ) ; +#96030 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96031 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96032 = VERTEX_POINT ( 'NONE', #79013 ) ; +#96033 = CYLINDRICAL_SURFACE ( 'NONE', #60196, 0.1000000000000000472 ) ; +#96034 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42296 ) ) ; +#96036 = FILL_AREA_STYLE_COLOUR ( '', #93353 ) ; +#96035 = FILL_AREA_STYLE ('',( #79243 ) ) ; +#96037 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96038 = VECTOR ( 'NONE', #43818, 1000.000000000000227 ) ; +#96039 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, -0.9000000000000014655, 0.000000000000000000 ) ) ; +#96040 = CARTESIAN_POINT ( 'NONE', ( -0.2499999999999990286, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#96041 = ORIENTED_EDGE ( 'NONE', *, *, #89470, .T. ) ; +#96042 = EDGE_CURVE ( 'NONE', #96313, #8011, #78497, .T. ) ; +#96043 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#96044 = SURFACE_SIDE_STYLE ('',( #27162 ) ) ; +#96045 = EDGE_CURVE ( 'NONE', #66120, #84331, #71347, .T. ) ; +#96046 = FILL_AREA_STYLE ('',( #81787 ) ) ; +#96047 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#96048 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#96049 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96050 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96051 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99044, 'distance_accuracy_value', 'NONE'); +#96052 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74882 ), #34173 ) ; +#96053 = FILL_AREA_STYLE_COLOUR ( '', #50274 ) ; +#96054 = ORIENTED_EDGE ( 'NONE', *, *, #90670, .T. ) ; +#96055 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96056 = VERTEX_POINT ( 'NONE', #25418 ) ; +#96057 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96058 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54004, 'distance_accuracy_value', 'NONE'); +#96059 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #12422, 'distance_accuracy_value', 'NONE'); +#96060 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96061 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 3.004385999999999779, 0.8991599999999999593 ) ) ; +#96062 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#96063 = ADVANCED_FACE ( 'NONE', ( #55560 ), #39191, .F. ) ; +#96064 = SURFACE_STYLE_USAGE ( .BOTH. , #81806 ) ; +#96065 = CARTESIAN_POINT ( 'NONE', ( 0.08634334415584400679, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#96066 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96067 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96068 = ORIENTED_EDGE ( 'NONE', *, *, #66929, .F. ) ; +#96069 = SURFACE_SIDE_STYLE ('',( #26179 ) ) ; +#96070 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, 3.099999999999989875, 0.000000000000000000 ) ) ; +#96071 = FILL_AREA_STYLE_COLOUR ( '', #19448 ) ; +#96072 = ORIENTED_EDGE ( 'NONE', *, *, #21245, .F. ) ; +#96073 = SURFACE_STYLE_USAGE ( .BOTH. , #72129 ) ; +#96074 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96075 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31932 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61008, #83968, #45611 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96076 = ORIENTED_EDGE ( 'NONE', *, *, #59647, .F. ) ; +#96077 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#96078 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96079 = ADVANCED_FACE ( 'NONE', ( #57073 ), #89191, .T. ) ; +#96080 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96081 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96082 = FILL_AREA_STYLE ('',( #89467 ) ) ; +#96083 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96084 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.600000000000000089, -11.90660254037844012 ) ) ; +#96085 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762689864, -0.01500000000000000118, -0.1458578643762691029 ) ) ; +#96086 = CARTESIAN_POINT ( 'NONE', ( -0.5497159090909089496, -1.258441558441560026, 0.8299999999999999600 ) ) ; +#96087 = ORIENTED_EDGE ( 'NONE', *, *, #91657, .F. ) ; +#96088 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63129 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43018, #4710, #35895 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96089 = FILL_AREA_STYLE ('',( #64482 ) ) ; +#96090 = AXIS2_PLACEMENT_3D ( 'NONE', #70223, #61092, #7864 ) ; +#96091 = PLANE ( 'NONE', #78855 ) ; +#96092 = EDGE_LOOP ( 'NONE', ( #69576, #96852, #45138, #53821 ) ) ; +#96093 = VECTOR ( 'NONE', #45426, 1000.000000000000000 ) ; +#96094 = ORIENTED_EDGE ( 'NONE', *, *, #40559, .T. ) ; +#96095 = VECTOR ( 'NONE', #63113, 1000.000000000000000 ) ; +#96096 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #99438, #93337, #6037, #54082 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96097 = PRESENTATION_STYLE_ASSIGNMENT (( #56365 ) ) ; +#96098 = CARTESIAN_POINT ( 'NONE', ( 13.90000000000000036, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#96099 = CARTESIAN_POINT ( 'NONE', ( 1.799693084787389985, -1.050822088410799937, 0.8300000000000004041 ) ) ; +#96100 = CARTESIAN_POINT ( 'NONE', ( -0.4442483664529159881, -1.083526083816420016, 0.8299999999999999600 ) ) ; +#96101 = LINE ( 'NONE', #42524, #16680 ) ; +#96103 = PLANE ( 'NONE', #84291 ) ; +#96102 = CARTESIAN_POINT ( 'NONE', ( 0.2924145224725209768, -0.9822800159449730506, 0.8100000000000000533 ) ) ; +#96104 = VERTEX_POINT ( 'NONE', #80042 ) ; +#96106 = ORIENTED_EDGE ( 'NONE', *, *, #44516, .F. ) ; +#96105 = ORIENTED_EDGE ( 'NONE', *, *, #50136, .T. ) ; +#96107 = ORIENTED_EDGE ( 'NONE', *, *, #4644, .F. ) ; +#96108 = SURFACE_STYLE_FILL_AREA ( #96614 ) ; +#96109 = EDGE_CURVE ( 'NONE', #67038, #79565, #35090, .T. ) ; +#96110 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #66318 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #86252, #48995, #1514 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96111 = EDGE_LOOP ( 'NONE', ( #92592, #93470, #94602, #69347 ) ) ; +#96113 = ORIENTED_EDGE ( 'NONE', *, *, #93728, .F. ) ; +#96112 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96114 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83104 ), #3146 ) ; +#96116 = PLANE ( 'NONE', #72634 ) ; +#96115 = SURFACE_STYLE_FILL_AREA ( #2226 ) ; +#96117 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96118 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#96119 = ORIENTED_EDGE ( 'NONE', *, *, #11944, .F. ) ; +#96120 = CARTESIAN_POINT ( 'NONE', ( 3.100000000000000533, 2.549999999999999822, 0.000000000000000000 ) ) ; +#96121 = LINE ( 'NONE', #74182, #71235 ) ; +#96122 = EDGE_LOOP ( 'NONE', ( #43619, #771, #16703, #96234 ) ) ; +#96123 = EDGE_CURVE ( 'NONE', #49262, #99548, #10984, .T. ) ; +#96124 = FILL_AREA_STYLE_COLOUR ( '', #17020 ) ; +#96125 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96126 = SURFACE_SIDE_STYLE ('',( #18011 ) ) ; +#96127 = STYLED_ITEM ( 'NONE', ( #95022 ), #50933 ) ; +#96128 = SURFACE_STYLE_USAGE ( .BOTH. , #81865 ) ; +#96129 = CARTESIAN_POINT ( 'NONE', ( 0.06988982237669021103, -1.070769809704489983, 0.8300000000000002931 ) ) ; +#96130 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29251 ), #71675 ) ; +#96132 = FILL_AREA_STYLE ('',( #27248 ) ) ; +#96131 = FILL_AREA_STYLE ('',( #49212 ) ) ; +#96133 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999999911, 2.500000000000000000, -0.02000000000000000042 ) ) ; +#96134 = SURFACE_STYLE_FILL_AREA ( #58408 ) ; +#96135 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30997 ), #66928 ) ; +#96136 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96137 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000022121, 3.500000000000000444, 0.000000000000000000 ) ) ; +#96138 = SURFACE_STYLE_USAGE ( .BOTH. , #96643 ) ; +#96139 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -2.276179938779915091, 0.000000000000000000 ) ) ; +#96140 = FILL_AREA_STYLE ('',( #95636 ) ) ; +#96141 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #18989, #9252, #17479, #40503 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96142 = VECTOR ( 'NONE', #21998, 1000.000000000000000 ) ; +#96143 = FILL_AREA_STYLE_COLOUR ( '', #99694 ) ; +#96144 = SURFACE_STYLE_FILL_AREA ( #33916 ) ; +#96145 = ORIENTED_EDGE ( 'NONE', *, *, #1949, .F. ) ; +#96146 = EDGE_CURVE ( 'NONE', #29025, #57698, #56935, .T. ) ; +#96147 = ADVANCED_FACE ( 'NONE', ( #73379 ), #34085, .T. ) ; +#96148 = PLANE ( 'NONE', #92743 ) ; +#96149 = DIRECTION ( 'NONE', ( -0.7071075504167448900, -0.7071060119555133694, 0.000000000000000000 ) ) ; +#96150 = CARTESIAN_POINT ( 'NONE', ( 4.382376697389419817, 1.415232237145633842, -11.91997175255800023 ) ) ; +#96151 = AXIS2_PLACEMENT_3D ( 'NONE', #97848, #20800, #67254 ) ; +#96152 = STYLED_ITEM ( 'NONE', ( #66754 ), #93271 ) ; +#96153 = LINE ( 'NONE', #35440, #80993 ) ; +#96154 = ORIENTED_EDGE ( 'NONE', *, *, #60597, .F. ) ; +#96155 = SURFACE_STYLE_USAGE ( .BOTH. , #89035 ) ; +#96156 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96158 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96157 = CARTESIAN_POINT ( 'NONE', ( 6.827451124874956534, 2.438700875125043854, 0.8991599999999999593 ) ) ; +#96159 = CARTESIAN_POINT ( 'NONE', ( 1.566233766233759983, -1.314082792207790007, 0.8100000000000000533 ) ) ; +#96160 = AXIS2_PLACEMENT_3D ( 'NONE', #56120, #23979, #447 ) ; +#96161 = SURFACE_SIDE_STYLE ('',( #73713 ) ) ; +#96162 = STYLED_ITEM ( 'NONE', ( #97697 ), #85433 ) ; +#96163 = VECTOR ( 'NONE', #28236, 1000.000000000000000 ) ; +#96164 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96165 = FACE_OUTER_BOUND ( 'NONE', #94513, .T. ) ; +#96166 = AXIS2_PLACEMENT_3D ( 'NONE', #75125, #37820, #29638 ) ; +#96167 = LINE ( 'NONE', #49758, #2151 ) ; +#96168 = ORIENTED_EDGE ( 'NONE', *, *, #92352, .F. ) ; +#96169 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.183333333333333570, 0.000000000000000000 ) ) ; +#96170 = EDGE_CURVE ( 'NONE', #30000, #10551, #45192, .T. ) ; +#96171 = STYLED_ITEM ( 'NONE', ( #55967 ), #6366 ) ; +#96172 = SURFACE_STYLE_USAGE ( .BOTH. , #51252 ) ; +#96173 = DIRECTION ( 'NONE', ( 0.7071067811865470176, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#96174 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96175 = CARTESIAN_POINT ( 'NONE', ( 1.695292207792210126, -1.507792207792209904, 0.8100000000000000533 ) ) ; +#96176 = SURFACE_STYLE_FILL_AREA ( #80909 ) ; +#96177 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#96178 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96179 = PRESENTATION_STYLE_ASSIGNMENT (( #79387 ) ) ; +#96180 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96181 = FILL_AREA_STYLE_COLOUR ( '', #64782 ) ; +#96182 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9501, 'distance_accuracy_value', 'NONE'); +#96183 = LINE ( 'NONE', #18061, #71892 ) ; +#96184 = PRESENTATION_STYLE_ASSIGNMENT (( #3787 ) ) ; +#96185 = STYLED_ITEM ( 'NONE', ( #26885 ), #64467 ) ; +#96186 = FILL_AREA_STYLE ('',( #65073 ) ) ; +#96187 = ORIENTED_EDGE ( 'NONE', *, *, #65002, .F. ) ; +#96188 = LINE ( 'NONE', #18586, #2366 ) ; +#96189 = ORIENTED_EDGE ( 'NONE', *, *, #71176, .T. ) ; +#96191 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #17503, 'distance_accuracy_value', 'NONE'); +#96190 = VECTOR ( 'NONE', #94844, 1000.000000000000000 ) ; +#96192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87158, 'distance_accuracy_value', 'NONE'); +#96193 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58337 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81028, #3886, #58563 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96194 = SURFACE_STYLE_FILL_AREA ( #58962 ) ; +#96195 = CARTESIAN_POINT ( 'NONE', ( 0.1743057588777000011, -1.390658178011239920, 0.8100000000000000533 ) ) ; +#96196 = ADVANCED_FACE ( 'NONE', ( #29893 ), #29408, .F. ) ; +#96197 = PRESENTATION_STYLE_ASSIGNMENT (( #86550 ) ) ; +#96198 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96199 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96200 = VERTEX_POINT ( 'NONE', #69165 ) ; +#96201 = SURFACE_STYLE_FILL_AREA ( #80419 ) ; +#96202 = PRESENTATION_STYLE_ASSIGNMENT (( #9368 ) ) ; +#96203 = EDGE_CURVE ( 'NONE', #28972, #13168, #84037, .T. ) ; +#96204 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40823, 'distance_accuracy_value', 'NONE'); +#96205 = CIRCLE ( 'NONE', #29387, 0.1999999999999996503 ) ; +#96206 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59347 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #34698, #4512, #11092 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96207 = ORIENTED_EDGE ( 'NONE', *, *, #71176, .F. ) ; +#96208 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96209 = PRESENTATION_STYLE_ASSIGNMENT (( #2324 ) ) ; +#96210 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#96211 = ADVANCED_FACE ( 'NONE', ( #100231 ), #65272, .F. ) ; +#96212 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.005000000000000004441, -0.1400000000000000411 ) ) ; +#96213 = ORIENTED_EDGE ( 'NONE', *, *, #87782, .T. ) ; +#96214 = PLANE ( 'NONE', #85702 ) ; +#96215 = FILL_AREA_STYLE_COLOUR ( '', #58765 ) ; +#96216 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31894, 'distance_accuracy_value', 'NONE'); +#96217 = ADVANCED_FACE ( 'NONE', ( #8852 ), #23266, .T. ) ; +#96218 = FACE_OUTER_BOUND ( 'NONE', #88340, .T. ) ; +#96219 = CARTESIAN_POINT ( 'NONE', ( 1.854016048130769923, -1.137681993439920047, 0.8099999999999998312 ) ) ; +#96220 = PRODUCT_DEFINITION ( 'δ֪', '', #95858, #15679 ) ; +#96221 = ORIENTED_EDGE ( 'NONE', *, *, #27305, .T. ) ; +#96222 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96223 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59593 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #90195, #29422, #84537 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96224 = CARTESIAN_POINT ( 'NONE', ( -1.316872272078025263, -1.169468177602907444, 0.8099999999998632738 ) ) ; +#96225 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -0.1499999999999999944, 0.2100000000000000200 ) ) ; +#96226 = FILL_AREA_STYLE ('',( #94210 ) ) ; +#96227 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #9577, #40831 ), + ( #25513, #56669 ), + ( #48996, #52496 ), + ( #59699, #50518 ), + ( #34691, #60193 ), + ( #21341, #91284 ), + ( #97409, #89294 ), + ( #35691, #81655 ), + ( #66794, #3530 ), + ( #27524, #97893 ), + ( #51010, #11589 ), + ( #74975, #89781 ), + ( #58678, #12099 ), + ( #28027, #73972 ), + ( #42335, #19841 ), + ( #65814, #42827 ), + ( #67785, #4992 ), + ( #98854, #36187 ), + ( #82151, #43319 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07032065289309799572, 0.1374144022168949930, 0.2016332655421010089, 0.2643675731736659928, 0.3250111489280210209, 0.3835880180669090089, 0.4413394827926420128, 0.4990328629798200244, 0.5566098983006150247, 0.6151075559507459545, 0.6744142209488209749, 0.7361813530434929698, 0.7993010937300539798, 0.8642599446468099966, 0.9308681698550169692, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96228 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96229 = ADVANCED_FACE ( 'NONE', ( #24807 ), #53896, .T. ) ; +#96230 = VECTOR ( 'NONE', #31991, 1000.000000000000000 ) ; +#96231 = EDGE_LOOP ( 'NONE', ( #25786, #24364, #76520, #66498 ) ) ; +#96234 = ORIENTED_EDGE ( 'NONE', *, *, #44372, .T. ) ; +#96233 = LINE ( 'NONE', #26336, #29623 ) ; +#96232 = STYLED_ITEM ( 'NONE', ( #5654 ), #85762 ) ; +#96235 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #62027 ) ) ; +#96236 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#96237 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#96238 = FACE_OUTER_BOUND ( 'NONE', #55490, .T. ) ; +#96239 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19666 ), #52265 ) ; +#96240 = FILL_AREA_STYLE_COLOUR ( '', #29147 ) ; +#96241 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.7000000000000000666, 0.000000000000000000 ) ) ; +#96242 = EDGE_LOOP ( 'NONE', ( #81208, #80724, #72285, #75598 ) ) ; +#96243 = ADVANCED_FACE ( 'NONE', ( #81446 ), #57969, .T. ) ; +#96244 = VECTOR ( 'NONE', #11274, 1000.000000000000114 ) ; +#96245 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96246 = LINE ( 'NONE', #76170, #32744 ) ; +#96247 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96248 = CARTESIAN_POINT ( 'NONE', ( -1.750000000000000222, 3.099999999999992095, 0.000000000000000000 ) ) ; +#96249 = ORIENTED_EDGE ( 'NONE', *, *, #86726, .T. ) ; +#96250 = EDGE_CURVE ( 'NONE', #66369, #30962, #9857, .T. ) ; +#96251 = CARTESIAN_POINT ( 'NONE', ( 4.387933249749911724, 8.569316249749912018, 0.8648700000000000276 ) ) ; +#96252 = ORIENTED_EDGE ( 'NONE', *, *, #14036, .T. ) ; +#96253 = EDGE_LOOP ( 'NONE', ( #63365, #57344, #86306, #29263 ) ) ; +#96254 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96256 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 4.900000000000000355, 0.03429000000000000103 ) ) ; +#96255 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 7.565224999999999866, 0.8648700000000000276 ) ) ; +#96257 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78036 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21709, #45171, #72213 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96258 = LINE ( 'NONE', #81505, #22872 ) ; +#96259 = EDGE_LOOP ( 'NONE', ( #93561, #97755, #75514, #46735 ) ) ; +#96260 = AXIS2_PLACEMENT_3D ( 'NONE', #97042, #25638, #17930 ) ; +#96261 = ORIENTED_EDGE ( 'NONE', *, *, #72771, .T. ) ; +#96262 = CARTESIAN_POINT ( 'NONE', ( 1.303582274605669999, -1.428972370004099934, 0.8100000000000000533 ) ) ; +#96263 = FACE_OUTER_BOUND ( 'NONE', #44135, .T. ) ; +#96264 = ORIENTED_EDGE ( 'NONE', *, *, #96027, .F. ) ; +#96265 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.950000000000000178, 0.03429000000000000103 ) ) ; +#96266 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, 0.1400000000000000133 ) ) ; +#96267 = CARTESIAN_POINT ( 'NONE', ( -1.311685777689840293, -1.173235213159260049, 0.8299999999999999600 ) ) ; +#96268 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#96269 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96270 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#96271 = SURFACE_STYLE_FILL_AREA ( #28365 ) ; +#96272 = CARTESIAN_POINT ( 'NONE', ( 0.5799999999567262421, 0.2999999999815374796, 5.437616897689447372E-17 ) ) ; +#96273 = LINE ( 'NONE', #91631, #86142 ) ; +#96274 = SURFACE_STYLE_FILL_AREA ( #66651 ) ; +#96275 = VERTEX_POINT ( 'NONE', #18073 ) ; +#96276 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#96278 = FILL_AREA_STYLE ('',( #1374 ) ) ; +#96277 = FILL_AREA_STYLE_COLOUR ( '', #88058 ) ; +#96279 = LINE ( 'NONE', #9454, #13930 ) ; +#96280 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21233 ), #52311 ) ; +#96281 = SURFACE_SIDE_STYLE ('',( #49348 ) ) ; +#96282 = CARTESIAN_POINT ( 'NONE', ( -0.1525548447364439841, -1.164073081312986702, 0.8299999999999999600 ) ) ; +#96283 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8648700000000000276 ) ) ; +#96284 = CARTESIAN_POINT ( 'NONE', ( 1.993397459621554901, 1.449999999999999956, -11.36999999999999922 ) ) ; +#96285 = SURFACE_STYLE_FILL_AREA ( #94776 ) ; +#96286 = ORIENTED_EDGE ( 'NONE', *, *, #46411, .F. ) ; +#96287 = FILL_AREA_STYLE ('',( #41709 ) ) ; +#96288 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #46406, #13721, #85227, #77577, #22442, #60290, #22968, #15246, #61291, #39264, #46918, #53603, #70405, #7535, #23466, #38775, #76066, #29117, #6058 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 2.237154160405338400E-05, 4.392642707855141026E-05, 6.494756354764243014E-05, 8.537355114040597493E-05, 0.0001053618251745383689, 0.0001245538749238299847, 0.0001434841242621595191, 0.0001621164538043667425, 0.0001807864333554518109, 0.0001994752094676594824, 0.0002184310921953052601, 0.0002380557755743199463, 0.0002583570343466929905, 0.0002791387056785798169, 0.0003008507101376167552, 0.0003236069630608051943 ), + .UNSPECIFIED. ) ; +#96289 = FACE_OUTER_BOUND ( 'NONE', #25976, .T. ) ; +#96290 = ADVANCED_FACE ( 'NONE', ( #43100 ), #80934, .F. ) ; +#96291 = FILL_AREA_STYLE_COLOUR ( '', #10461 ) ; +#96292 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#96293 = VECTOR ( 'NONE', #9922, 1000.000000000000000 ) ; +#96294 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16393 ) ) ; +#96295 = CARTESIAN_POINT ( 'NONE', ( 0.4459649354204920368, -1.149076952450200029, 0.8300000000000015143 ) ) ; +#96296 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95450, 'distance_accuracy_value', 'NONE'); +#96297 = CARTESIAN_POINT ( 'NONE', ( 10.05860099999999946, 12.65647100000000158, 0.8991599999999999593 ) ) ; +#96298 = CARTESIAN_POINT ( 'NONE', ( 13.40000000000000036, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#96299 = CARTESIAN_POINT ( 'NONE', ( 2.099999999999996980, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#96300 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40121 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76295, #46660, #30317 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96301 = VECTOR ( 'NONE', #31012, 1000.000000000000114 ) ; +#96302 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#96303 = CARTESIAN_POINT ( 'NONE', ( -0.5610005133853442905, 2.432921575926970004, 0.8100000000000000533 ) ) ; +#96304 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96305 = CARTESIAN_POINT ( 'NONE', ( -0.2500000000000000000, 0.4699999999999999734, -0.2250000000000000333 ) ) ; +#96306 = VECTOR ( 'NONE', #64150, 1000.000000000000000 ) ; +#96307 = SURFACE_STYLE_FILL_AREA ( #28404 ) ; +#96308 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 1.050000000000000044 ) ) ; +#96309 = FILL_AREA_STYLE ('',( #88190 ) ) ; +#96310 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #19536, 'design' ) ; +#96311 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#96312 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96313 = VERTEX_POINT ( 'NONE', #89079 ) ; +#96314 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66966 ), #34422 ) ; +#96315 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91560, 'distance_accuracy_value', 'NONE'); +#96316 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93242, 'distance_accuracy_value', 'NONE'); +#96317 = FACE_OUTER_BOUND ( 'NONE', #98550, .T. ) ; +#96318 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19754 ), #66969 ) ; +#96319 = LINE ( 'NONE', #72352, #38996 ) ; +#96320 = PLANE ( 'NONE', #62392 ) ; +#96321 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#96322 = AXIS2_PLACEMENT_3D ( 'NONE', #12345, #74720, #51752 ) ; +#96323 = EDGE_LOOP ( 'NONE', ( #18800, #15920, #59829, #32700 ) ) ; +#96324 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97904 ), #99463 ) ; +#96326 = ADVANCED_FACE ( 'NONE', ( #21126 ), #44103, .T. ) ; +#96325 = LINE ( 'NONE', #95311, #24575 ) ; +#96327 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59728 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52219, #44501, #21540 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96328 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31101, 'distance_accuracy_value', 'NONE'); +#96329 = FILL_AREA_STYLE ('',( #34107 ) ) ; +#96330 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19693, 'distance_accuracy_value', 'NONE'); +#96331 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96332 = ORIENTED_EDGE ( 'NONE', *, *, #24205, .T. ) ; +#96333 = ORIENTED_EDGE ( 'NONE', *, *, #13857, .T. ) ; +#96334 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96335 = LINE ( 'NONE', #95837, #11500 ) ; +#96336 = ORIENTED_EDGE ( 'NONE', *, *, #87800, .F. ) ; +#96338 = CARTESIAN_POINT ( 'NONE', ( 0.2546877245216000452, -1.031834659001420018, 0.8299999999999996270 ) ) ; +#96337 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #149 ), #66989 ) ; +#96339 = LINE ( 'NONE', #95328, #59644 ) ; +#96340 = PRESENTATION_STYLE_ASSIGNMENT (( #32590 ) ) ; +#96341 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.000000000000000000 ) ) ; +#96342 = AXIS2_PLACEMENT_3D ( 'NONE', #56091, #1956, #18753 ) ; +#96343 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96344 = SHAPE_DEFINITION_REPRESENTATION ( #23012, #82675 ) ; +#96345 = FILL_AREA_STYLE_COLOUR ( '', #45706 ) ; +#96347 = ORIENTED_EDGE ( 'NONE', *, *, #26927, .F. ) ; +#96346 = EDGE_LOOP ( 'NONE', ( #97337, #9098, #63116, #85459 ) ) ; +#96348 = STYLED_ITEM ( 'NONE', ( #51436 ), #45191 ) ; +#96349 = ORIENTED_EDGE ( 'NONE', *, *, #80661, .F. ) ; +#96350 = ORIENTED_EDGE ( 'NONE', *, *, #89116, .F. ) ; +#96351 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96352 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 15.15000000000000036, 0.000000000000000000 ) ) ; +#96353 = SURFACE_STYLE_FILL_AREA ( #40769 ) ; +#96354 = VERTEX_POINT ( 'NONE', #83425 ) ; +#96355 = EDGE_CURVE ( 'NONE', #82666, #6059, #60954, .T. ) ; +#96356 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#96357 = ORIENTED_EDGE ( 'NONE', *, *, #13125, .F. ) ; +#96358 = ORIENTED_EDGE ( 'NONE', *, *, #45406, .F. ) ; +#96360 = FACE_OUTER_BOUND ( 'NONE', #95101, .T. ) ; +#96359 = FILL_AREA_STYLE ('',( #36643 ) ) ; +#96361 = ORIENTED_EDGE ( 'NONE', *, *, #33772, .F. ) ; +#96362 = VERTEX_POINT ( 'NONE', #82921 ) ; +#96363 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #76858 ) ) ; +#96364 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999996181, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#96365 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#96367 = EDGE_CURVE ( 'NONE', #58869, #96887, #67715, .T. ) ; +#96366 = CARTESIAN_POINT ( 'NONE', ( 5.971853000000000300, 6.264147999999999605, 0.8648700000000000276 ) ) ; +#96368 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71995 ), #21397 ) ; +#96370 = ORIENTED_EDGE ( 'NONE', *, *, #54130, .T. ) ; +#96369 = FILL_AREA_STYLE_COLOUR ( '', #16847 ) ; +#96371 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67097 ), #80177 ) ; +#96372 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 8.800000000000000711, 0.03429000000000000103 ) ) ; +#96373 = ORIENTED_EDGE ( 'NONE', *, *, #15892, .T. ) ; +#96374 = STYLED_ITEM ( 'NONE', ( #78711 ), #94893 ) ; +#96375 = CARTESIAN_POINT ( 'NONE', ( -0.1117694805194810043, -0.9000000000000001332, 0.8100000000000000533 ) ) ; +#96376 = PLANE ( 'NONE', #34341 ) ; +#96377 = EDGE_LOOP ( 'NONE', ( #100056, #71099, #3350, #54179 ) ) ; +#96379 = CARTESIAN_POINT ( 'NONE', ( 1.050000000000000044, 3.099999999999980549, 0.000000000000000000 ) ) ; +#96378 = DIRECTION ( 'NONE', ( 0.3631942952377801292, 0.000000000000000000, -0.9317134237021232890 ) ) ; +#96380 = EDGE_LOOP ( 'NONE', ( #86733, #31236, #24489, #32509 ) ) ; +#96381 = EDGE_CURVE ( 'NONE', #44869, #2421, #37470, .T. ) ; +#96382 = ORIENTED_EDGE ( 'NONE', *, *, #7362, .T. ) ; +#96384 = SURFACE_STYLE_USAGE ( .BOTH. , #71426 ) ; +#96383 = CYLINDRICAL_SURFACE ( 'NONE', #40765, 0.01000000000000002623 ) ; +#96385 = VECTOR ( 'NONE', #35512, 1000.000000000000000 ) ; +#96386 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96387 = CARTESIAN_POINT ( 'NONE', ( 9.641736750250085919, 8.392539249749912500, 0.8991599999999999593 ) ) ; +#96388 = FILL_AREA_STYLE ('',( #57663 ) ) ; +#96389 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #5060 ), #37752 ) ; +#96390 = LINE ( 'NONE', #34665, #67019 ) ; +#96391 = DIRECTION ( 'NONE', ( 1.175494350822289960E-30, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96393 = EDGE_CURVE ( 'NONE', #36125, #4926, #72624, .T. ) ; +#96392 = SURFACE_STYLE_USAGE ( .BOTH. , #50501 ) ; +#96394 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#96395 = ORIENTED_EDGE ( 'NONE', *, *, #16098, .F. ) ; +#96396 = AXIS2_PLACEMENT_3D ( 'NONE', #42472, #73605, #3151 ) ; +#96397 = ORIENTED_EDGE ( 'NONE', *, *, #39231, .F. ) ; +#96398 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44323 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #56746, #72041, #95983 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96399 = LINE ( 'NONE', #26501, #16214 ) ; +#96400 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220065281, 0.8999999999999999112, 0.000000000000000000 ) ) ; +#96401 = EDGE_CURVE ( 'NONE', #6289, #94240, #68975, .T. ) ; +#96402 = CARTESIAN_POINT ( 'NONE', ( 1.432999986405000037, -1.279077976066830047, 0.8299999999999999600 ) ) ; +#96403 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#96404 = SURFACE_STYLE_USAGE ( .BOTH. , #58671 ) ; +#96405 = SURFACE_STYLE_USAGE ( .BOTH. , #34685 ) ; +#96406 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96407 = SURFACE_SIDE_STYLE ('',( #42822 ) ) ; +#96408 = ORIENTED_EDGE ( 'NONE', *, *, #26524, .F. ) ; +#96409 = CARTESIAN_POINT ( 'NONE', ( 8.510365999999999431, 9.523910000000002540, 0.8991599999999999593 ) ) ; +#96410 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.899999999999999911, 0.000000000000000000 ) ) ; +#96411 = EDGE_CURVE ( 'NONE', #1838, #40353, #84409, .T. ) ; +#96412 = LINE ( 'NONE', #33675, #59264 ) ; +#96413 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96414 = SURFACE_STYLE_FILL_AREA ( #11086 ) ; +#96415 = SURFACE_STYLE_FILL_AREA ( #4995 ) ; +#96416 = EDGE_CURVE ( 'NONE', #53905, #62254, #75261, .T. ) ; +#96417 = LINE ( 'NONE', #26521, #32613 ) ; +#96418 = CARTESIAN_POINT ( 'NONE', ( 12.19999999999999929, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#96419 = PRESENTATION_STYLE_ASSIGNMENT (( #65303 ) ) ; +#96420 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96421 = FILL_AREA_STYLE_COLOUR ( '', #29948 ) ; +#96422 = SURFACE_STYLE_USAGE ( .BOTH. , #97907 ) ; +#96423 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77140, 'distance_accuracy_value', 'NONE'); +#96424 = ORIENTED_EDGE ( 'NONE', *, *, #14546, .T. ) ; +#96425 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96426 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.63512000000000057, 0.8991599999999999593 ) ) ; +#96427 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96428 = EDGE_LOOP ( 'NONE', ( #41324, #63081, #93949 ) ) ; +#96429 = LINE ( 'NONE', #73990, #56015 ) ; +#96430 = FILL_AREA_STYLE ('',( #34211 ) ) ; +#96431 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8299999999999999600 ) ) ; +#96432 = CARTESIAN_POINT ( 'NONE', ( 8.559863000000000000, 10.39365100000000020, 0.8648700000000000276 ) ) ; +#96433 = VECTOR ( 'NONE', #80254, 1000.000000000000000 ) ; +#96434 = STYLED_ITEM ( 'NONE', ( #99886 ), #34325 ) ; +#96435 = FILL_AREA_STYLE_COLOUR ( '', #24815 ) ; +#96436 = CARTESIAN_POINT ( 'NONE', ( 1.783305012356700026, -1.001398657004090254, 0.8100000000000006084 ) ) ; +#96437 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100961 ) ; +#96438 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96439 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96440 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8648700000000000276 ) ) ; +#96441 = ORIENTED_EDGE ( 'NONE', *, *, #95624, .F. ) ; +#96442 = ORIENTED_EDGE ( 'NONE', *, *, #98186, .F. ) ; +#96443 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #99561, #78202 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #58616 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#96444 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, 3.499999999999969802, -0.02000000000000000042 ) ) ; +#96445 = EDGE_CURVE ( 'NONE', #31184, #41056, #14415, .T. ) ; +#96446 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83443 ), #94910 ) ; +#96447 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#96448 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8991599999999999593 ) ) ; +#96449 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, -3.099999999999989875, 0.000000000000000000 ) ) ; +#96450 = EDGE_CURVE ( 'NONE', #90714, #56519, #45988, .T. ) ; +#96451 = FACE_OUTER_BOUND ( 'NONE', #28301, .T. ) ; +#96452 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96453 = FILL_AREA_STYLE ('',( #50061 ) ) ; +#96454 = VERTEX_POINT ( 'NONE', #58969 ) ; +#96455 = PRESENTATION_STYLE_ASSIGNMENT (( #50065 ) ) ; +#96456 = VECTOR ( 'NONE', #26538, 1000.000000000000000 ) ; +#96457 = ORIENTED_EDGE ( 'NONE', *, *, #92081, .T. ) ; +#96458 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.6600000000000000311, -1.050000000000000044 ) ) ; +#96459 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96460 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.450000000000000178, 0.000000000000000000 ) ) ; +#96461 = CARTESIAN_POINT ( 'NONE', ( -1.143806093516799960, -0.9548508715965600135, 0.8100000000000000533 ) ) ; +#96462 = AXIS2_PLACEMENT_3D ( 'NONE', #7841, #24294, #93650 ) ; +#96463 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96464 = FACE_OUTER_BOUND ( 'NONE', #15843, .T. ) ; +#96465 = FACE_OUTER_BOUND ( 'NONE', #25305, .T. ) ; +#96466 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96467 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #81797 ), #94793 ) ; +#96469 = EDGE_LOOP ( 'NONE', ( #599, #48919, #34157, #72393 ) ) ; +#96468 = ORIENTED_EDGE ( 'NONE', *, *, #93252, .F. ) ; +#96470 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #52523 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66134, #50836, #97721 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96471 = PLANE ( 'NONE', #30500 ) ; +#96472 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96473 = VERTEX_POINT ( 'NONE', #12884 ) ; +#96474 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96475 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 3.500000000000000444, -1.450207831659080759E-157 ) ) ; +#96476 = ORIENTED_EDGE ( 'NONE', *, *, #89949, .T. ) ; +#96477 = VECTOR ( 'NONE', #45561, 1000.000000000000000 ) ; +#96479 = EDGE_CURVE ( 'NONE', #67209, #85090, #51285, .T. ) ; +#96478 = ORIENTED_EDGE ( 'NONE', *, *, #57501, .F. ) ; +#96480 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96481 = FILL_AREA_STYLE ('',( #50084 ) ) ; +#96482 = SURFACE_SIDE_STYLE ('',( #34257 ) ) ; +#96483 = DIRECTION ( 'NONE', ( 0.7071060119555140355, -0.7071075504167442238, 0.000000000000000000 ) ) ; +#96485 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 9.650000000000000355, 0.000000000000000000 ) ) ; +#96484 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96486 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, -3.266666666666653285, 0.000000000000000000 ) ) ; +#96487 = VERTEX_POINT ( 'NONE', #28774 ) ; +#96488 = ORIENTED_EDGE ( 'NONE', *, *, #55056, .F. ) ; +#96489 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#96490 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39434 ), #31344 ) ; +#96491 = ORIENTED_EDGE ( 'NONE', *, *, #2392, .T. ) ; +#96492 = PRESENTATION_STYLE_ASSIGNMENT (( #97496 ) ) ; +#96493 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #11600 ), #91555 ) ; +#96495 = ORIENTED_EDGE ( 'NONE', *, *, #26892, .F. ) ; +#96494 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.500000000000000000, 0.1829999999999999960 ) ) ; +#96496 = LINE ( 'NONE', #50097, #32804 ) ; +#96497 = FILL_AREA_STYLE_COLOUR ( '', #97077 ) ; +#96498 = ORIENTED_EDGE ( 'NONE', *, *, #25555, .T. ) ; +#96499 = DIRECTION ( 'NONE', ( -0.7071067811865465735, 0.7071067811865485719, 0.000000000000000000 ) ) ; +#96500 = FILL_AREA_STYLE ('',( #49087 ) ) ; +#96501 = ORIENTED_EDGE ( 'NONE', *, *, #2599, .F. ) ; +#96502 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96503 = SURFACE_STYLE_USAGE ( .BOTH. , #50107 ) ; +#96504 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.400000000000000355, 0.000000000000000000 ) ) ; +#96505 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60573 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89227, #73413, #65750 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96506 = PRESENTATION_STYLE_ASSIGNMENT (( #43416 ) ) ; +#96507 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#96508 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96509 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #54121 ) ) ; +#96510 = PRESENTATION_STYLE_ASSIGNMENT (( #75088 ) ) ; +#96511 = DIRECTION ( 'NONE', ( 0.7071062811861722475, -0.7071072811865692920, 0.000000000000000000 ) ) ; +#96512 = VECTOR ( 'NONE', #44814, 1000.000000000000000 ) ; +#96514 = LINE ( 'NONE', #86879, #72700 ) ; +#96513 = CARTESIAN_POINT ( 'NONE', ( 12.55000000000000071, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#96515 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#96516 = VERTEX_POINT ( 'NONE', #91071 ) ; +#96517 = LINE ( 'NONE', #26622, #83229 ) ; +#96518 = SURFACE_STYLE_FILL_AREA ( #42446 ) ; +#96519 = ORIENTED_EDGE ( 'NONE', *, *, #63828, .T. ) ; +#96520 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45593 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40527, #4217, #20031 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96521 = CARTESIAN_POINT ( 'NONE', ( 5.236461000000000254, 9.417844000000002325, 0.8991599999999999593 ) ) ; +#96522 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #37882 ) ) ; +#96523 = EDGE_CURVE ( 'NONE', #39791, #42170, #31211, .T. ) ; +#96524 = CARTESIAN_POINT ( 'NONE', ( -0.2819971453420380136, -1.430103682213279992, 0.8100000000000000533 ) ) ; +#96525 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220055511, 0.09999999999999988065, -0.02000000000000000042 ) ) ; +#96526 = FILL_AREA_STYLE_COLOUR ( '', #19249 ) ; +#96528 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96527 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96529 = FILL_AREA_STYLE ('',( #33791 ) ) ; +#96530 = PLANE ( 'NONE', #74350 ) ; +#96531 = AXIS2_PLACEMENT_3D ( 'NONE', #20947, #15242, #21436 ) ; +#96532 = EDGE_CURVE ( 'NONE', #61609, #93808, #38960, .T. ) ; +#96533 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #94923 ) ) ; +#96534 = SURFACE_SIDE_STYLE ('',( #81280 ) ) ; +#96535 = CARTESIAN_POINT ( 'NONE', ( -2.000000000000000000, -2.000000000000000000, -0.02000000000000000042 ) ) ; +#96536 = EDGE_CURVE ( 'NONE', #75765, #62914, #6714, .T. ) ; +#96537 = VERTEX_POINT ( 'NONE', #77756 ) ; +#96538 = VECTOR ( 'NONE', #51675, 1000.000000000000000 ) ; +#96539 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.400000000000000355, 0.000000000000000000 ) ) ; +#96540 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -1.699999999999999956, -0.02000000000000000042 ) ) ; +#96541 = VECTOR ( 'NONE', #76176, 1000.000000000000000 ) ; +#96542 = DIRECTION ( 'NONE', ( 0.7071067811865475727, 0.7071067811865475727, 0.000000000000000000 ) ) ; +#96543 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33023 ) ) ; +#96544 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30208, 'distance_accuracy_value', 'NONE'); +#96545 = ORIENTED_EDGE ( 'NONE', *, *, #91835, .F. ) ; +#96546 = PLANE ( 'NONE', #21273 ) ; +#96547 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571430157, 0.6899999999999999467, 0.5000000000000000000 ) ) ; +#96548 = FILL_AREA_STYLE_COLOUR ( '', #97960 ) ; +#96549 = CARTESIAN_POINT ( 'NONE', ( -1.102215942591399989, -0.9616422087329199453, 0.8299999999999999600 ) ) ; +#96550 = LINE ( 'NONE', #97047, #6927 ) ; +#96551 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96552 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 1.149999999999999911, 0.000000000000000000 ) ) ; +#96553 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96554 = LINE ( 'NONE', #72588, #67784 ) ; +#96555 = SURFACE_STYLE_USAGE ( .BOTH. , #48261 ) ; +#96556 = CARTESIAN_POINT ( 'NONE', ( -1.092088612093490063, -1.441583773770549914, 0.8300000000000001821 ) ) ; +#96557 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #85016 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99915, #67380, #6034 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96558 = CARTESIAN_POINT ( 'NONE', ( 0.6421266233766219633, -1.227272727272729957, 0.8299999999999999600 ) ) ; +#96559 = FILL_AREA_STYLE ('',( #4646 ) ) ; +#96560 = VERTEX_POINT ( 'NONE', #15949 ) ; +#96561 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #43352 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74410, #16099, #45226 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96562 = ORIENTED_EDGE ( 'NONE', *, *, #31175, .T. ) ; +#96563 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96564 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.6999999999999990674, 0.1829999999999790128 ) ) ; +#96565 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83334, 'distance_accuracy_value', 'NONE'); +#96566 = CARTESIAN_POINT ( 'NONE', ( -0.1988983467373149905, -1.000931601726380071, 0.8100000000000000533 ) ) ; +#96567 = CARTESIAN_POINT ( 'NONE', ( 0.4270339786724932640, -1.261873021140253570, 0.8100000000000002753 ) ) ; +#96568 = DIRECTION ( 'NONE', ( 0.3438200982495990266, -0.000000000000000000, -0.9390355371548171348 ) ) ; +#96569 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96570 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96571 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999949818, -2.100000000000000089, 0.1829999999999500082 ) ) ; +#96572 = SURFACE_STYLE_USAGE ( .BOTH. , #64960 ) ; +#96573 = ADVANCED_FACE ( 'NONE', ( #71108 ), #140, .T. ) ; +#96574 = ORIENTED_EDGE ( 'NONE', *, *, #92691, .T. ) ; +#96575 = FACE_OUTER_BOUND ( 'NONE', #63764, .T. ) ; +#96576 = DIRECTION ( 'NONE', ( -1.000000000000000000, 1.274473528905959955E-45, 1.498136433501504447E-75 ) ) ; +#96577 = ORIENTED_EDGE ( 'NONE', *, *, #6157, .F. ) ; +#96578 = STYLED_ITEM ( 'NONE', ( #29063 ), #37410 ) ; +#96579 = VECTOR ( 'NONE', #16527, 1000.000000000000000 ) ; +#96580 = SURFACE_STYLE_USAGE ( .BOTH. , #34359 ) ; +#96581 = EDGE_LOOP ( 'NONE', ( #5655, #9594, #95872, #19799 ) ) ; +#96582 = STYLED_ITEM ( 'NONE', ( #52606 ), #60501 ) ; +#96583 = SURFACE_SIDE_STYLE ('',( #49164 ) ) ; +#96584 = STYLED_ITEM ( 'NONE', ( #43975 ), #36508 ) ; +#96585 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.276179938779915091, -0.02000000000000000042 ) ) ; +#96586 = VECTOR ( 'NONE', #98155, 1000.000000000000000 ) ; +#96587 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96588 = CARTESIAN_POINT ( 'NONE', ( 0.2900000000000000355, -0.01499999999999999771, -0.1458578643762691029 ) ) ; +#96589 = LINE ( 'NONE', #72632, #78969 ) ; +#96590 = VERTEX_POINT ( 'NONE', #14919 ) ; +#96591 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78601 ) ) ; +#96592 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96593 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 4.291319999999999801, 0.8991599999999999593 ) ) ; +#96594 = ORIENTED_EDGE ( 'NONE', *, *, #5015, .T. ) ; +#96595 = SURFACE_SIDE_STYLE ('',( #19518 ) ) ; +#96596 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #31230, 'distance_accuracy_value', 'NONE'); +#96597 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96598 = AXIS2_PLACEMENT_3D ( 'NONE', #72945, #2995, #88273 ) ; +#96600 = ADVANCED_FACE ( 'NONE', ( #1151 ), #46066, .T. ) ; +#96599 = VERTEX_POINT ( 'NONE', #16437 ) ; +#96601 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 0.03429000000000000103 ) ) ; +#96602 = PRESENTATION_STYLE_ASSIGNMENT (( #73163 ) ) ; +#96603 = PRESENTATION_STYLE_ASSIGNMENT (( #57355 ) ) ; +#96604 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96605 = VECTOR ( 'NONE', #35103, 1000.000000000000000 ) ; +#96606 = SURFACE_STYLE_USAGE ( .BOTH. , #40519 ) ; +#96608 = DIRECTION ( 'NONE', ( 7.228014483236695569E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96607 = CARTESIAN_POINT ( 'NONE', ( 0.3027121684171390492, -0.9750598911029030313, 0.8299999999999999600 ) ) ; +#96609 = VERTEX_POINT ( 'NONE', #7224 ) ; +#96611 = ORIENTED_EDGE ( 'NONE', *, *, #25336, .F. ) ; +#96610 = ORIENTED_EDGE ( 'NONE', *, *, #16107, .T. ) ; +#96612 = ADVANCED_FACE ( 'NONE', ( #38461 ), #23145, .T. ) ; +#96613 = ORIENTED_EDGE ( 'NONE', *, *, #69513, .F. ) ; +#96614 = FILL_AREA_STYLE ('',( #3710 ) ) ; +#96615 = VECTOR ( 'NONE', #57323, 1000.000000000000000 ) ; +#96616 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96617 = ORIENTED_EDGE ( 'NONE', *, *, #65112, .T. ) ; +#96619 = ORIENTED_EDGE ( 'NONE', *, *, #57537, .T. ) ; +#96618 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999979927, 0.5000000000000000000, 1.048695503451053346E-76 ) ) ; +#96620 = PRESENTATION_STYLE_ASSIGNMENT (( #10788 ) ) ; +#96621 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#96622 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96623 = ORIENTED_EDGE ( 'NONE', *, *, #43397, .F. ) ; +#96624 = CARTESIAN_POINT ( 'NONE', ( 13.18093600000000087, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#96625 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96626 = ORIENTED_EDGE ( 'NONE', *, *, #48180, .F. ) ; +#96627 = EDGE_CURVE ( 'NONE', #100777, #81743, #1685, .T. ) ; +#96628 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96629 = EDGE_CURVE ( 'NONE', #72010, #50740, #49660, .T. ) ; +#96630 = CARTESIAN_POINT ( 'NONE', ( 0.1500000000000000777, 0.2500000000000000000, -0.8499999999999996447 ) ) ; +#96631 = FILL_AREA_STYLE ('',( #65500 ) ) ; +#96632 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96633 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #54149 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40226, #42242, #10989 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96634 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46186 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26859, #96254, #58025 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96635 = LINE ( 'NONE', #33389, #99918 ) ; +#96636 = SURFACE_STYLE_USAGE ( .BOTH. , #10808 ) ; +#96637 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96638 = STYLED_ITEM ( 'NONE', ( #98222 ), #75838 ) ; +#96639 = ADVANCED_FACE ( 'NONE', ( #3173 ), #26177, .T. ) ; +#96640 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3890 ), #3742 ) ; +#96641 = VECTOR ( 'NONE', #10719, 1000.000000000000000 ) ; +#96642 = CARTESIAN_POINT ( 'NONE', ( 1.063574105442089968, -1.082231071007949907, 0.8300000000000022915 ) ) ; +#96643 = SURFACE_SIDE_STYLE ('',( #28244 ) ) ; +#96645 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #44531 ) ) ; +#96644 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -11.91999999999999993 ) ) ; +#96646 = CARTESIAN_POINT ( 'NONE', ( -0.9015827922077920276, 0.7099999999999999645, 0.000000000000000000 ) ) ; +#96647 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98202 ) ) ; +#96648 = VECTOR ( 'NONE', #92392, 1000.000000000000000 ) ; +#96649 = CARTESIAN_POINT ( 'NONE', ( 1.009265655561859987, -0.9654894655288509542, 0.8299999999999999600 ) ) ; +#96650 = ORIENTED_EDGE ( 'NONE', *, *, #7752, .F. ) ; +#96651 = CARTESIAN_POINT ( 'NONE', ( -1.219099199802559985, -1.508462442331270026, 0.8300000000000024025 ) ) ; +#96652 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96653 = EDGE_CURVE ( 'NONE', #14577, #96693, #58349, .T. ) ; +#96654 = PRESENTATION_STYLE_ASSIGNMENT (( #66536 ) ) ; +#96655 = EDGE_LOOP ( 'NONE', ( #99029, #28341, #91712, #60761 ) ) ; +#96656 = SURFACE_SIDE_STYLE ('',( #50761 ) ) ; +#96657 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#96659 = PRESENTATION_STYLE_ASSIGNMENT (( #73227 ) ) ; +#96658 = PLANE ( 'NONE', #71946 ) ; +#96661 = VECTOR ( 'NONE', #66503, 1000.000000000000000 ) ; +#96660 = CARTESIAN_POINT ( 'NONE', ( 1.608893861054889962, -1.000931601726380071, 0.8100000000000000533 ) ) ; +#96662 = CARTESIAN_POINT ( 'NONE', ( -0.2277176615892120282, -1.378252124432310044, 0.8299999999999999600 ) ) ; +#96663 = AXIS2_PLACEMENT_3D ( 'NONE', #11962, #27387, #43185 ) ; +#96664 = CARTESIAN_POINT ( 'NONE', ( 0.2835602027787479940, -1.357109198394020000, 0.8299999999999999600 ) ) ; +#96665 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#96666 = SURFACE_STYLE_USAGE ( .BOTH. , #3271 ) ; +#96667 = FILL_AREA_STYLE ('',( #65536 ) ) ; +#96668 = ORIENTED_EDGE ( 'NONE', *, *, #82277, .T. ) ; +#96669 = CARTESIAN_POINT ( 'NONE', ( 8.948771999999999949, 9.085504000000002023, 0.8991599999999999593 ) ) ; +#96670 = PLANE ( 'NONE', #23374 ) ; +#96671 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96672 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#96673 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #21600, #83892, #89556, #13889 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96674 = DIRECTION ( 'NONE', ( -0.7071067811865489050, 0.7071067811865462405, 0.000000000000000000 ) ) ; +#96675 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96676 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96677 = VECTOR ( 'NONE', #77888, 1000.000000000000000 ) ; +#96678 = ADVANCED_FACE ( 'NONE', ( #40489 ), #87431, .T. ) ; +#96679 = FILL_AREA_STYLE ('',( #89054 ) ) ; +#96680 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#96681 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #19236, #88212, #48421, #89210 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96682 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96683 = ORIENTED_EDGE ( 'NONE', *, *, #69679, .F. ) ; +#96684 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3711 ), #31478 ) ; +#96685 = ORIENTED_EDGE ( 'NONE', *, *, #45875, .F. ) ; +#96686 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 9.150000000000000355, 0.03429000000000000103 ) ) ; +#96687 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96688 = PRESENTATION_STYLE_ASSIGNMENT (( #26299 ) ) ; +#96689 = DIRECTION ( 'NONE', ( -1.626303258728260102E-16, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96690 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96691 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#96692 = EDGE_CURVE ( 'NONE', #43302, #75965, #4180, .T. ) ; +#96693 = VERTEX_POINT ( 'NONE', #6117 ) ; +#96694 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96695 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74777 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63932, #62943, #47595 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96696 = FILL_AREA_STYLE ('',( #9372 ) ) ; +#96697 = ORIENTED_EDGE ( 'NONE', *, *, #94523, .T. ) ; +#96698 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 3.149999999999990141, -0.02000000000000000042 ) ) ; +#96699 = AXIS2_PLACEMENT_3D ( 'NONE', #85657, #61698, #7462 ) ; +#96700 = VECTOR ( 'NONE', #656, 1000.000000000000000 ) ; +#96701 = FILL_AREA_STYLE ('',( #56967 ) ) ; +#96702 = CARTESIAN_POINT ( 'NONE', ( 6.544609000000000343, 2.721543000000000490, 0.8991599999999999593 ) ) ; +#96703 = FILL_AREA_STYLE ('',( #17099 ) ) ; +#96704 = VECTOR ( 'NONE', #88009, 1000.000000000000000 ) ; +#96705 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.9833333333333335036, 0.000000000000000000 ) ) ; +#96706 = ORIENTED_EDGE ( 'NONE', *, *, #4101, .F. ) ; +#96707 = CARTESIAN_POINT ( 'NONE', ( 10.41995600000000088, 2.598279999999999923, 0.8991599999999999593 ) ) ; +#96708 = CARTESIAN_POINT ( 'NONE', ( -0.09999999999999931166, -3.149999999999979927, 0.000000000000000000 ) ) ; +#96709 = SURFACE_SIDE_STYLE ('',( #88089 ) ) ; +#96710 = STYLED_ITEM ( 'NONE', ( #40065 ), #19554 ) ; +#96711 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #50301 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23766, #30901, #29405 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96712 = PRESENTATION_STYLE_ASSIGNMENT (( #94704 ) ) ; +#96713 = EDGE_LOOP ( 'NONE', ( #73222, #29505, #76274, #28649 ) ) ; +#96714 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39678 ) ) ; +#96715 = STYLED_ITEM ( 'NONE', ( #20447 ), #19046 ) ; +#96716 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #3750 ) ) ; +#96717 = SURFACE_STYLE_USAGE ( .BOTH. , #33993 ) ; +#96718 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96719 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96720 = CARTESIAN_POINT ( 'NONE', ( -1.207082774155606719, -1.212686486869581026, 0.8099999999998312994 ) ) ; +#96721 = SURFACE_SIDE_STYLE ('',( #3826 ) ) ; +#96722 = AXIS2_PLACEMENT_3D ( 'NONE', #97751, #57530, #58548 ) ; +#96723 = EDGE_CURVE ( 'NONE', #51946, #81900, #36460, .T. ) ; +#96724 = ADVANCED_FACE ( 'NONE', ( #13778 ), #20494, .T. ) ; +#96725 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #28253 ) ) ; +#96726 = AXIS2_PLACEMENT_3D ( 'NONE', #27063, #85041, #46206 ) ; +#96727 = STYLED_ITEM ( 'NONE', ( #62061 ), #9404 ) ; +#96728 = ORIENTED_EDGE ( 'NONE', *, *, #46994, .F. ) ; +#96729 = ORIENTED_EDGE ( 'NONE', *, *, #38284, .T. ) ; +#96730 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76879, 'distance_accuracy_value', 'NONE'); +#96731 = FACE_OUTER_BOUND ( 'NONE', #47583, .T. ) ; +#96732 = SURFACE_STYLE_FILL_AREA ( #56993 ) ; +#96733 = LINE ( 'NONE', #59015, #93631 ) ; +#96734 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96735 = ORIENTED_EDGE ( 'NONE', *, *, #89320, .T. ) ; +#96736 = EDGE_CURVE ( 'NONE', #79986, #27880, #51678, .T. ) ; +#96737 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96738 = EDGE_CURVE ( 'NONE', #2359, #76650, #99843, .T. ) ; +#96739 = PRESENTATION_STYLE_ASSIGNMENT (( #34522 ) ) ; +#96740 = FILL_AREA_STYLE ('',( #65128 ) ) ; +#96741 = VECTOR ( 'NONE', #20117, 1000.000000000000000 ) ; +#96742 = ORIENTED_EDGE ( 'NONE', *, *, #91776, .T. ) ; +#96743 = ADVANCED_FACE ( 'NONE', ( #66962 ), #81810, .T. ) ; +#96745 = FILL_AREA_STYLE ('',( #90111 ) ) ; +#96744 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#96746 = ORIENTED_EDGE ( 'NONE', *, *, #46970, .T. ) ; +#96747 = ORIENTED_EDGE ( 'NONE', *, *, #91947, .F. ) ; +#96748 = CARTESIAN_POINT ( 'NONE', ( 1.073443162354087210, -1.190413013056340397, 0.8099999999998699352 ) ) ; +#96750 = LINE ( 'NONE', #25855, #82558 ) ; +#96749 = LINE ( 'NONE', #96255, #49563 ) ; +#96751 = AXIS2_PLACEMENT_3D ( 'NONE', #93225, #60641, #78449 ) ; +#96752 = ORIENTED_EDGE ( 'NONE', *, *, #78591, .F. ) ; +#96753 = SURFACE_STYLE_FILL_AREA ( #44156 ) ; +#96754 = EDGE_CURVE ( 'NONE', #61508, #31741, #78151, .T. ) ; +#96755 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96756 = EDGE_LOOP ( 'NONE', ( #82909, #37378, #52328, #59268 ) ) ; +#96757 = PRESENTATION_STYLE_ASSIGNMENT (( #49854 ) ) ; +#96758 = STYLED_ITEM ( 'NONE', ( #55822 ), #53245 ) ; +#96759 = ORIENTED_EDGE ( 'NONE', *, *, #28212, .F. ) ; +#96760 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96761 = CARTESIAN_POINT ( 'NONE', ( -1.063525042275559995, -1.248384608377719918, 0.8299999999999999600 ) ) ; +#96763 = EDGE_CURVE ( 'NONE', #33248, #4405, #69958, .T. ) ; +#96762 = LINE ( 'NONE', #18666, #4112 ) ; +#96764 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5425 ) ) ; +#96765 = CARTESIAN_POINT ( 'NONE', ( -0.5500000000000000444, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#96766 = CARTESIAN_POINT ( 'NONE', ( 8.277020999999999518, 1.851801000000000030, 0.8648700000000000276 ) ) ; +#96767 = STYLED_ITEM ( 'NONE', ( #19509 ), #26162 ) ; +#96768 = FILL_AREA_STYLE_COLOUR ( '', #91513 ) ; +#96769 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#96770 = ADVANCED_FACE ( 'NONE', ( #46461 ), #32194, .T. ) ; +#96771 = VERTEX_POINT ( 'NONE', #7595 ) ; +#96772 = SURFACE_STYLE_FILL_AREA ( #43354 ) ; +#96773 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96774 = EDGE_CURVE ( 'NONE', #58097, #2974, #27625, .T. ) ; +#96775 = VECTOR ( 'NONE', #54766, 999.9999999999998863 ) ; +#96777 = FILL_AREA_STYLE ('',( #65668 ) ) ; +#96776 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96778 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #48135, 'distance_accuracy_value', 'NONE'); +#96779 = SURFACE_STYLE_USAGE ( .BOTH. , #2897 ) ; +#96780 = FILL_AREA_STYLE_COLOUR ( '', #72326 ) ; +#96781 = CARTESIAN_POINT ( 'NONE', ( -1.296446609406726402, 0.7099999999999999645, 1.050000000000000044 ) ) ; +#96782 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#96783 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96784 = LINE ( 'NONE', #2397, #75456 ) ; +#96785 = ORIENTED_EDGE ( 'NONE', *, *, #92024, .T. ) ; +#96786 = FACE_OUTER_BOUND ( 'NONE', #80479, .T. ) ; +#96787 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96788 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96790 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70722 ), #36491 ) ; +#96789 = FACE_OUTER_BOUND ( 'NONE', #8504, .T. ) ; +#96792 = AXIS2_PLACEMENT_3D ( 'NONE', #78584, #85246, #54640 ) ; +#96791 = SURFACE_STYLE_FILL_AREA ( #73358 ) ; +#96793 = LINE ( 'NONE', #19197, #22352 ) ; +#96794 = CARTESIAN_POINT ( 'NONE', ( 0.2400000000000000189, -0.04999999999999999584, 0.08229670385730990245 ) ) ; +#96795 = PLANE ( 'NONE', #70158 ) ; +#96797 = PLANE ( 'NONE', #9241 ) ; +#96796 = STYLED_ITEM ( 'NONE', ( #92610 ), #61155 ) ; +#96798 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #60054, #51376, #91160, #60549 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96799 = SURFACE_STYLE_USAGE ( .BOTH. , #42221 ) ; +#96800 = CIRCLE ( 'NONE', #15214, 0.009999999999999998473 ) ; +#96801 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72336 ) ) ; +#96802 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96803 = ADVANCED_FACE ( 'NONE', ( #45444 ), #30142, .T. ) ; +#96804 = SURFACE_STYLE_USAGE ( .BOTH. , #35084 ) ; +#96805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78829 ), #88673 ) ; +#96806 = CARTESIAN_POINT ( 'NONE', ( 10.92867099999999958, 7.105605000000000615, 0.8991599999999999593 ) ) ; +#96807 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#96808 = CARTESIAN_POINT ( 'NONE', ( 1.708426850688339993, -1.163903542943879987, 0.8299999999999997380 ) ) ; +#96809 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1096, #48598, #87873, #32256, #33774, #79739, #17900, #47558, #39909 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999995559, 0.3749999999999989453, 0.4999999999999983347, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96810 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96811 = EDGE_CURVE ( 'NONE', #46104, #17990, #55697, .T. ) ; +#96812 = ORIENTED_EDGE ( 'NONE', *, *, #100393, .T. ) ; +#96813 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#96814 = CARTESIAN_POINT ( 'NONE', ( -1.499999999999999778, -3.266666666666659946, 0.000000000000000000 ) ) ; +#96815 = AXIS2_PLACEMENT_3D ( 'NONE', #51178, #52183, #59369 ) ; +#96816 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96817 = ADVANCED_FACE ( 'NONE', ( #94940 ), #65330, .T. ) ; +#96818 = LINE ( 'NONE', #57583, #60245 ) ; +#96819 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16844, #94465, #54177, #86831, #23545, #48030, #79174, #45960, #85812, #68951, #38856, #92441, #92926, #85299, #22515, #15324, #84796 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 2, 1, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.1250000000000007494, 0.1875000000000010547, 0.2500000000000012768, 0.5000000000000019984, 0.6250000000000022204, 0.6875000000000023315, 0.7187500000000022204, 0.7500000000000019984, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96820 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1416 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #5305, #19672, #36520 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96821 = LINE ( 'NONE', #71877, #70526 ) ; +#96822 = LINE ( 'NONE', #33587, #69527 ) ; +#96823 = ORIENTED_EDGE ( 'NONE', *, *, #86390, .T. ) ; +#96824 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 11.35000000000000142, 0.000000000000000000 ) ) ; +#96826 = EDGE_CURVE ( 'NONE', #87237, #79474, #26059, .T. ) ; +#96825 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#96827 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96828 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 0.4749999999999999778, 0.2399999999999999911 ) ) ; +#96829 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41420 ) ) ; +#96830 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #12168, #43391, #60743, #61257 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#96831 = PLANE ( 'NONE', #15947 ) ; +#96832 = VERTEX_POINT ( 'NONE', #64338 ) ; +#96833 = VERTEX_POINT ( 'NONE', #87817 ) ; +#96834 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #2352 ) ) ; +#96835 = AXIS2_PLACEMENT_3D ( 'NONE', #2641, #28505, #36688 ) ; +#96836 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96837 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#96838 = ORIENTED_EDGE ( 'NONE', *, *, #88147, .T. ) ; +#96839 = CARTESIAN_POINT ( 'NONE', ( 1.795983389471520031, -1.255590633215009966, 0.8100000000000000533 ) ) ; +#96840 = CARTESIAN_POINT ( 'NONE', ( 11.10544700000000162, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#96841 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#96842 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96843 = EDGE_CURVE ( 'NONE', #20528, #19588, #86813, .T. ) ; +#96844 = FILL_AREA_STYLE ('',( #50453 ) ) ; +#96845 = EDGE_CURVE ( 'NONE', #78654, #27289, #34231, .T. ) ; +#96846 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #65161, #49184 ) ; +#96847 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#96849 = VERTEX_POINT ( 'NONE', #96449 ) ; +#96848 = ORIENTED_EDGE ( 'NONE', *, *, #1914, .T. ) ; +#96850 = VECTOR ( 'NONE', #23477, 1000.000000000000000 ) ; +#96851 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33111 ) ) ; +#96852 = ORIENTED_EDGE ( 'NONE', *, *, #89647, .F. ) ; +#96853 = ORIENTED_EDGE ( 'NONE', *, *, #15223, .F. ) ; +#96854 = AXIS2_PLACEMENT_3D ( 'NONE', #10172, #56273, #85870 ) ; +#96855 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #32725, 'distance_accuracy_value', 'NONE'); +#96856 = CARTESIAN_POINT ( 'NONE', ( 1.885232907775660216, -1.407232784796780045, 0.8299999999999999600 ) ) ; +#96857 = ORIENTED_EDGE ( 'NONE', *, *, #13789, .F. ) ; +#96858 = AXIS2_PLACEMENT_3D ( 'NONE', #4770, #66560, #56936 ) ; +#96859 = ADVANCED_FACE ( 'NONE', ( #16821 ), #72005, .T. ) ; +#96860 = SURFACE_STYLE_USAGE ( .BOTH. , #59648 ) ; +#96861 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96862 = EDGE_CURVE ( 'NONE', #79989, #60372, #25061, .T. ) ; +#96863 = AXIS2_PLACEMENT_3D ( 'NONE', #95914, #70424, #25024 ) ; +#96864 = ORIENTED_EDGE ( 'NONE', *, *, #20346, .T. ) ; +#96865 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#96866 = ORIENTED_EDGE ( 'NONE', *, *, #9665, .F. ) ; +#96868 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96867 = SURFACE_STYLE_FILL_AREA ( #5427 ) ; +#96869 = EDGE_LOOP ( 'NONE', ( #69067, #70816, #53079, #21625 ) ) ; +#96870 = ORIENTED_EDGE ( 'NONE', *, *, #43550, .F. ) ; +#96871 = SURFACE_SIDE_STYLE ('',( #11040 ) ) ; +#96872 = STYLED_ITEM ( 'NONE', ( #47128 ), #97265 ) ; +#96873 = CARTESIAN_POINT ( 'NONE', ( 1.897707761045830166, -1.292112914554750080, 0.8300000000000004041 ) ) ; +#96875 = ORIENTED_EDGE ( 'NONE', *, *, #70033, .T. ) ; +#96874 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.2999999999999989897, 0.000000000000000000 ) ) ; +#96876 = ORIENTED_EDGE ( 'NONE', *, *, #30068, .F. ) ; +#96878 = EDGE_CURVE ( 'NONE', #38354, #2457, #100518, .T. ) ; +#96877 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86568 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #6176, #77, #53712 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96879 = FILL_AREA_STYLE ('',( #17771 ) ) ; +#96880 = PRESENTATION_STYLE_ASSIGNMENT (( #80610 ) ) ; +#96881 = ORIENTED_EDGE ( 'NONE', *, *, #81501, .T. ) ; +#96883 = SURFACE_SIDE_STYLE ('',( #54088 ) ) ; +#96882 = SURFACE_STYLE_FILL_AREA ( #72935 ) ; +#96884 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80791 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69866, #8004, #70368 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96885 = CARTESIAN_POINT ( 'NONE', ( 0.9238200612200860862, -3.099999999999980549, 0.000000000000000000 ) ) ; +#96886 = ORIENTED_EDGE ( 'NONE', *, *, #58189, .F. ) ; +#96887 = VERTEX_POINT ( 'NONE', #29052 ) ; +#96889 = CARTESIAN_POINT ( 'NONE', ( 10.08014299999999963, 4.574163000000001311, 0.8991599999999999593 ) ) ; +#96888 = SURFACE_SIDE_STYLE ('',( #65788 ) ) ; +#96890 = EDGE_CURVE ( 'NONE', #71570, #11036, #19880, .T. ) ; +#96891 = CARTESIAN_POINT ( 'NONE', ( 3.425241999999999898, 2.769338999999999995, 0.8991599999999999593 ) ) ; +#96892 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.2750000000000000222, -0.1499999999999999944 ) ) ; +#96893 = VECTOR ( 'NONE', #28827, 1000.000000000000000 ) ; +#96894 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#96895 = FACE_OUTER_BOUND ( 'NONE', #66247, .T. ) ; +#96896 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96897 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73595, 'distance_accuracy_value', 'NONE'); +#96898 = ADVANCED_FACE ( 'NONE', ( #81691 ), #59742, .T. ) ; +#96899 = VERTEX_POINT ( 'NONE', #5519 ) ; +#96900 = CARTESIAN_POINT ( 'NONE', ( 0.03330623534528640017, -1.205608583660890076, 0.8100000000000000533 ) ) ; +#96901 = ORIENTED_EDGE ( 'NONE', *, *, #99827, .T. ) ; +#96902 = EDGE_CURVE ( 'NONE', #32845, #87078, #90834, .T. ) ; +#96903 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.9499999999999999556, 0.000000000000000000 ) ) ; +#96904 = CARTESIAN_POINT ( 'NONE', ( 1.441086107696939900, -1.316410597191429943, 0.8100000000000000533 ) ) ; +#96905 = FACE_OUTER_BOUND ( 'NONE', #84950, .T. ) ; +#96906 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#96907 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8199999999999999512 ) ) ; +#96908 = CARTESIAN_POINT ( 'NONE', ( 5.130395000000000039, 8.392538999999999305, 0.8648700000000000276 ) ) ; +#96909 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96910 = VERTEX_POINT ( 'NONE', #51050 ) ; +#96911 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96912 = DIRECTION ( 'NONE', ( -1.784971879987599845E-14, 1.918759123245459951E-15, -1.000000000000000000 ) ) ; +#96913 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5512 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36369, #100025, #59882 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96914 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96915 = LINE ( 'NONE', #74483, #80441 ) ; +#96916 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 11.30020599999999931, 0.8648700000000000276 ) ) ; +#96917 = LINE ( 'NONE', #51014, #20676 ) ; +#96918 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 3.149999999999979927, 0.000000000000000000 ) ) ; +#96919 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#96920 = AXIS2_PLACEMENT_3D ( 'NONE', #92423, #37347, #84288 ) ; +#96921 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #59056 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17514, #55375, #79334 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#96922 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 11.35000000000000142, 0.03429000000000000103 ) ) ; +#96923 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96924 = EDGE_CURVE ( 'NONE', #26181, #18530, #82193, .T. ) ; +#96926 = CARTESIAN_POINT ( 'NONE', ( 0.2337662337662329837, -1.437662337662340084, 0.8100000000000000533 ) ) ; +#96925 = STYLED_ITEM ( 'NONE', ( #9327 ), #76863 ) ; +#96927 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#96928 = SURFACE_STYLE_FILL_AREA ( #65823 ) ; +#96929 = FILL_AREA_STYLE ('',( #96421 ) ) ; +#96930 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96931 = VECTOR ( 'NONE', #76073, 1000.000000000000000 ) ; +#96933 = VERTEX_POINT ( 'NONE', #44341 ) ; +#96932 = CIRCLE ( 'NONE', #5590, 0.009999999999999998473 ) ; +#96934 = FILL_AREA_STYLE_COLOUR ( '', #78595 ) ; +#96935 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#96937 = ADVANCED_FACE ( 'NONE', ( #89333 ), #43357, .F. ) ; +#96936 = SURFACE_SIDE_STYLE ('',( #57701 ) ) ; +#96938 = ORIENTED_EDGE ( 'NONE', *, *, #21052, .T. ) ; +#96939 = SURFACE_STYLE_USAGE ( .BOTH. , #81173 ) ; +#96940 = CARTESIAN_POINT ( 'NONE', ( 10.41851699999999958, 10.77099800000000052, 0.8991599999999999593 ) ) ; +#96941 = SURFACE_SIDE_STYLE ('',( #9102 ) ) ; +#96942 = STYLED_ITEM ( 'NONE', ( #14223 ), #27069 ) ; +#96943 = ADVANCED_FACE ( 'NONE', ( #39096 ), #1812, .F. ) ; +#96944 = FILL_AREA_STYLE_COLOUR ( '', #20350 ) ; +#96945 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96946 = EDGE_LOOP ( 'NONE', ( #97509, #2977, #52528, #62266 ) ) ; +#96947 = EDGE_LOOP ( 'NONE', ( #80295, #49582, #91960, #78805 ) ) ; +#96948 = FILL_AREA_STYLE_COLOUR ( '', #43831 ) ; +#96949 = EDGE_CURVE ( 'NONE', #1880, #35737, #23791, .T. ) ; +#96950 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4425, 'distance_accuracy_value', 'NONE'); +#96951 = FACE_OUTER_BOUND ( 'NONE', #62495, .T. ) ; +#96952 = DIRECTION ( 'NONE', ( -0.7071067811865472397, 0.7071067811865479058, 0.000000000000000000 ) ) ; +#96953 = DIRECTION ( 'NONE', ( -1.000000000000000000, -1.274473528905959955E-45, -1.498136433501504447E-75 ) ) ; +#96954 = CARTESIAN_POINT ( 'NONE', ( -0.4757099785863510011, -1.161113228842870049, 0.8100000000000000533 ) ) ; +#96955 = CIRCLE ( 'NONE', #62744, 1.319494367338009955 ) ; +#96956 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#96957 = CARTESIAN_POINT ( 'NONE', ( -1.185463345515916922, -0.8848889651143551083, 0.8100000000000729949 ) ) ; +#96958 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#96959 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762689864, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#96960 = ORIENTED_EDGE ( 'NONE', *, *, #96479, .F. ) ; +#96961 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #66021 ), #44772 ) ; +#96962 = ORIENTED_EDGE ( 'NONE', *, *, #47344, .T. ) ; +#96963 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96964 = LINE ( 'NONE', #19382, #33933 ) ; +#96965 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 0.000000000000000000, 0.000000000000000000 ) ) ; +#96966 = EDGE_CURVE ( 'NONE', #76663, #81565, #47761, .T. ) ; +#96967 = EDGE_CURVE ( 'NONE', #33648, #85668, #99296, .T. ) ; +#96968 = CARTESIAN_POINT ( 'NONE', ( -1.011710337664210035, -1.062017517080650064, 0.8299999999999999600 ) ) ; +#96969 = SURFACE_SIDE_STYLE ('',( #73530 ) ) ; +#96970 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#96973 = VERTEX_POINT ( 'NONE', #25316 ) ; +#96972 = ORIENTED_EDGE ( 'NONE', *, *, #12428, .T. ) ; +#96971 = AXIS2_PLACEMENT_3D ( 'NONE', #66164, #97281, #89656 ) ; +#96974 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.4245906043549200204, -0.02000000000000000042 ) ) ; +#96975 = EDGE_CURVE ( 'NONE', #12539, #22947, #54942, .T. ) ; +#96976 = ORIENTED_EDGE ( 'NONE', *, *, #30658, .F. ) ; +#96977 = STYLED_ITEM ( 'NONE', ( #57445 ), #89741 ) ; +#96978 = ORIENTED_EDGE ( 'NONE', *, *, #32169, .F. ) ; +#96979 = ORIENTED_EDGE ( 'NONE', *, *, #63770, .T. ) ; +#96980 = STYLED_ITEM ( 'NONE', ( #16735 ), #82537 ) ; +#96981 = EDGE_CURVE ( 'NONE', #7621, #80372, #7966, .T. ) ; +#96982 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#96983 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#96984 = SURFACE_SIDE_STYLE ('',( #81724 ) ) ; +#96985 = VERTEX_POINT ( 'NONE', #16083 ) ; +#96986 = VERTEX_POINT ( 'NONE', #71239 ) ; +#96987 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49748 ), #77466 ) ; +#96988 = ORIENTED_EDGE ( 'NONE', *, *, #6005, .T. ) ; +#96989 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#96990 = ORIENTED_EDGE ( 'NONE', *, *, #57033, .T. ) ; +#96991 = VECTOR ( 'NONE', #82421, 1000.000000000000000 ) ; +#96992 = DIRECTION ( 'NONE', ( 0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#96993 = CARTESIAN_POINT ( 'NONE', ( 1.897517923509739912, -1.370875895369189967, 0.8099999999999996092 ) ) ; +#96994 = ORIENTED_EDGE ( 'NONE', *, *, #74981, .T. ) ; +#96996 = SURFACE_STYLE_USAGE ( .BOTH. , #51099 ) ; +#96995 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #51357 ) ) ; +#96997 = CARTESIAN_POINT ( 'NONE', ( -1.097320596538975179, -1.444270688870364694, 0.8099999999996606581 ) ) ; +#96998 = EDGE_LOOP ( 'NONE', ( #77895, #98178, #65896, #70877 ) ) ; +#96999 = VERTEX_POINT ( 'NONE', #79424 ) ; +#97000 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.53504399999999919, 0.8648700000000000276 ) ) ; +#97002 = VECTOR ( 'NONE', #82618, 1000.000000000000000 ) ; +#97001 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97003 = DIRECTION ( 'NONE', ( -0.2853456824793029201, -0.9584246665703157753, 0.000000000000000000 ) ) ; +#97004 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97005 = CARTESIAN_POINT ( 'NONE', ( -1.116693831898450062, -1.233317951191559958, 0.8300000000000000711 ) ) ; +#97006 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81948, #79932, #96705, #35490 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97007 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97008 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1528 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81404, #95646, #66051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97009 = FACE_OUTER_BOUND ( 'NONE', #17929, .T. ) ; +#97010 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97011 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.383333333333330195, 0.000000000000000000 ) ) ; +#97012 = CARTESIAN_POINT ( 'NONE', ( 11.05594999999999928, 6.978326000000000029, 0.8991599999999999593 ) ) ; +#97013 = ORIENTED_EDGE ( 'NONE', *, *, #73552, .T. ) ; +#97014 = CARTESIAN_POINT ( 'NONE', ( -0.9340909090909089718, -1.077394480519480169, 0.8299999999999999600 ) ) ; +#97015 = VERTEX_POINT ( 'NONE', #1298 ) ; +#97016 = EDGE_CURVE ( 'NONE', #16570, #81483, #30920, .T. ) ; +#97017 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #835 ), #38317 ) ; +#97018 = PRESENTATION_STYLE_ASSIGNMENT (( #89394 ) ) ; +#97019 = SURFACE_SIDE_STYLE ('',( #65393 ) ) ; +#97020 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -1.899999999999999911, 1.048695503451051965E-76 ) ) ; +#97022 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39988 ), #92144 ) ; +#97021 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#97023 = EDGE_CURVE ( 'NONE', #100002, #12677, #69709, .T. ) ; +#97024 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97025 = LINE ( 'NONE', #81274, #56887 ) ; +#97026 = SURFACE_STYLE_FILL_AREA ( #18429 ) ; +#97027 = DIRECTION ( 'NONE', ( -2.478176394252580155E-16, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97028 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100211 ) ) ; +#97029 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39999 ) ) ; +#97030 = FILL_AREA_STYLE_COLOUR ( '', #1014 ) ; +#97031 = EDGE_LOOP ( 'NONE', ( #3603, #10007, #23992, #30512 ) ) ; +#97032 = PLANE ( 'NONE', #63533 ) ; +#97033 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #15280 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38011, #14470, #30309 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97034 = EDGE_CURVE ( 'NONE', #81943, #47921, #17102, .T. ) ; +#97036 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97035 = CARTESIAN_POINT ( 'NONE', ( 0.002476875442262489995, -1.267073986156890930, 0.8099999999998471756 ) ) ; +#97037 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#97038 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97039 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97040 = VECTOR ( 'NONE', #50508, 1000.000000000000114 ) ; +#97041 = ORIENTED_EDGE ( 'NONE', *, *, #100657, .T. ) ; +#97042 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -1.300000000000000266, -0.02000000000000000042 ) ) ; +#97044 = ADVANCED_FACE ( 'NONE', ( #40622 ), #71754, .F. ) ; +#97043 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97045 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#97046 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#97047 = CARTESIAN_POINT ( 'NONE', ( 4.974832000000000143, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#97048 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #90598 ) ) ; +#97049 = VECTOR ( 'NONE', #26655, 1000.000000000000000 ) ; +#97050 = PRESENTATION_STYLE_ASSIGNMENT (( #51142 ) ) ; +#97051 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97052 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#97053 = DIRECTION ( 'NONE', ( 0.7071067804170475535, 0.7071067819560475920, 0.000000000000000000 ) ) ; +#97054 = STYLED_ITEM ( 'NONE', ( #8867 ), #48676 ) ; +#97055 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #70996 ), #8956 ) ; +#97056 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #56008, #42681 ), + ( #35546, #43160 ), + ( #73333, #50380 ), + ( #2881, #88625 ), + ( #57023, #74324 ), + ( #18665, #34034 ), + ( #88143, #81000 ), + ( #66155, #42191 ), + ( #59038, #73823 ), + ( #18144, #96267 ), + ( #49857, #65151 ), + ( #49335, #3860 ), + ( #9923, #89646 ), + ( #26366, #97748 ), + ( #89142, #35043 ), + ( #10943, #50856 ), + ( #81520, #81999 ), + ( #57523, #11441 ), + ( #90128, #25866 ), + ( #66641, #19694 ), + ( #80484, #96761 ), + ( #95757, #41183 ), + ( #10412, #4362 ), + ( #3377, #41685 ), + ( #48844, #97268 ), + ( #34543, #79992 ), + ( #72297, #65650 ), + ( #72818, #27365 ), + ( #26872, #58041 ), + ( #19175, #2375 ), + ( #33528, #64650 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.03814092977640389653, 0.07324469314986049862, 0.1061969321809869971, 0.1374304763707679955, 0.1678896035485339944, 0.1977315896515779992, 0.2280232376912230130, 0.2586940336098749738, 0.2899912476047389887, 0.3221726268997219811, 0.3550576746715989884, 0.3890409003039089764, 0.4584870114880090219, 0.5284665488555919666, 0.5980717268930320074, 0.6665294321140310396, 0.6996665789640289512, 0.7315154747723879858, 0.7619337275606480331, 0.7912372011617729850, 0.8192113105742789836, 0.8457594638444070334, 0.8709908791189380217, 0.8957711837317919867, 0.9201022408770099803, 0.9449582991602709647, 0.9714845733685939511, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97057 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86330, 'distance_accuracy_value', 'NONE'); +#97058 = LINE ( 'NONE', #98017, #12697 ) ; +#97059 = VECTOR ( 'NONE', #40907, 1000.000000000000000 ) ; +#97060 = EDGE_LOOP ( 'NONE', ( #28923, #49974, #89418, #89596 ) ) ; +#97061 = ORIENTED_EDGE ( 'NONE', *, *, #68722, .T. ) ; +#97062 = EDGE_CURVE ( 'NONE', #19143, #51096, #97006, .T. ) ; +#97063 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63187, 'distance_accuracy_value', 'NONE'); +#97064 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3597, 'distance_accuracy_value', 'NONE'); +#97065 = FACE_OUTER_BOUND ( 'NONE', #81919, .T. ) ; +#97066 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#97067 = FILL_AREA_STYLE ('',( #64955 ) ) ; +#97068 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, -0.1250000000000000000 ) ) ; +#97069 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18808 ), #51515 ) ; +#97070 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97071 = VECTOR ( 'NONE', #46841, 1000.000000000000000 ) ; +#97072 = EDGE_CURVE ( 'NONE', #85200, #98144, #80950, .T. ) ; +#97073 = ORIENTED_EDGE ( 'NONE', *, *, #42005, .F. ) ; +#97074 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#97075 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 7.450000000000000178, 0.000000000000000000 ) ) ; +#97078 = VECTOR ( 'NONE', #55264, 1000.000000000000000 ) ; +#97077 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97076 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97079 = ORIENTED_EDGE ( 'NONE', *, *, #85248, .T. ) ; +#97080 = FILL_AREA_STYLE ('',( #33843 ) ) ; +#97081 = STYLED_ITEM ( 'NONE', ( #3283 ), #98884 ) ; +#97082 = LINE ( 'NONE', #89461, #14180 ) ; +#97083 = ORIENTED_EDGE ( 'NONE', *, *, #47586, .F. ) ; +#97084 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #60755 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74192, #27754, #21075 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97085 = EDGE_CURVE ( 'NONE', #48032, #65103, #88084, .T. ) ; +#97086 = EDGE_CURVE ( 'NONE', #69635, #62754, #72761, .T. ) ; +#97087 = CARTESIAN_POINT ( 'NONE', ( -0.8190005133853439645, 2.061746575926969971, 0.8100000000000000533 ) ) ; +#97088 = SURFACE_STYLE_USAGE ( .BOTH. , #37367 ) ; +#97089 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999959338, -0.1400000000000000411 ) ) ; +#97090 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97091 = ORIENTED_EDGE ( 'NONE', *, *, #63372, .T. ) ; +#97092 = STYLED_ITEM ( 'NONE', ( #55849 ), #3560 ) ; +#97094 = EDGE_CURVE ( 'NONE', #8603, #79706, #41129, .T. ) ; +#97093 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97095 = ADVANCED_FACE ( 'NONE', ( #10883 ), #61812, .T. ) ; +#97096 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 12.19999999999999929, 0.03429000000000000103 ) ) ; +#97097 = ORIENTED_EDGE ( 'NONE', *, *, #80570, .T. ) ; +#97098 = AXIS2_PLACEMENT_3D ( 'NONE', #87447, #38975, #78292 ) ; +#97099 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999999556, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#97100 = SURFACE_SIDE_STYLE ('',( #57347 ) ) ; +#97101 = ORIENTED_EDGE ( 'NONE', *, *, #5152, .T. ) ; +#97102 = VERTEX_POINT ( 'NONE', #75275 ) ; +#97103 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#97105 = ADVANCED_FACE ( 'NONE', ( #83439 ), #76255, .F. ) ; +#97104 = SURFACE_SIDE_STYLE ('',( #74164 ) ) ; +#97106 = FILL_AREA_STYLE_COLOUR ( '', #80514 ) ; +#97108 = PRESENTATION_STYLE_ASSIGNMENT (( #88983 ) ) ; +#97107 = SURFACE_SIDE_STYLE ('',( #49697 ) ) ; +#97109 = VERTEX_POINT ( 'NONE', #52308 ) ; +#97112 = ORIENTED_EDGE ( 'NONE', *, *, #25172, .F. ) ; +#97111 = ORIENTED_EDGE ( 'NONE', *, *, #5114, .T. ) ; +#97110 = VECTOR ( 'NONE', #50986, 1000.000000000000000 ) ; +#97113 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97114 = VERTEX_POINT ( 'NONE', #59982 ) ; +#97115 = EDGE_CURVE ( 'NONE', #8779, #99269, #91086, .T. ) ; +#97116 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97117 = ORIENTED_EDGE ( 'NONE', *, *, #45456, .F. ) ; +#97118 = ORIENTED_EDGE ( 'NONE', *, *, #31153, .F. ) ; +#97119 = SURFACE_SIDE_STYLE ('',( #20033 ) ) ; +#97120 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #10459 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81687, #66345, #95436 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97121 = CARTESIAN_POINT ( 'NONE', ( 0.2761799387799149796, -3.099999999999980105, -0.02000000000000000042 ) ) ; +#97122 = VECTOR ( 'NONE', #58555, 1000.000000000000000 ) ; +#97123 = VERTEX_POINT ( 'NONE', #13921 ) ; +#97124 = CARTESIAN_POINT ( 'NONE', ( -0.5824878246753240063, 0.7099999999999999645, 0.2077922077922080002 ) ) ; +#97125 = LINE ( 'NONE', #66511, #36995 ) ; +#97126 = ORIENTED_EDGE ( 'NONE', *, *, #79045, .F. ) ; +#97127 = CARTESIAN_POINT ( 'NONE', ( 0.9238200612200860862, 3.099999999999980549, 0.000000000000000000 ) ) ; +#97128 = VECTOR ( 'NONE', #44148, 999.9999999999998863 ) ; +#97129 = VECTOR ( 'NONE', #99378, 1000.000000000000000 ) ; +#97130 = CARTESIAN_POINT ( 'NONE', ( 0.5390356320350060404, -1.127406710959419911, 0.8299999999999999600 ) ) ; +#97132 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.7099999999999999645, 0.8000000000000003775 ) ) ; +#97131 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64520 ) ) ; +#97133 = STYLED_ITEM ( 'NONE', ( #52310 ), #48846 ) ; +#97134 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.500000000000000000, -0.02000000000000000042 ) ) ; +#97135 = CARTESIAN_POINT ( 'NONE', ( 1.743271607193970008, -1.437850337629750008, 0.8100000000000000533 ) ) ; +#97136 = FILL_AREA_STYLE ('',( #19039 ) ) ; +#97137 = CARTESIAN_POINT ( 'NONE', ( 3.123820061220085265, 2.499999999999999556, -0.02000000000000000042 ) ) ; +#97138 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #48295 ) ) ; +#97139 = LINE ( 'NONE', #32880, #60369 ) ; +#97140 = CARTESIAN_POINT ( 'NONE', ( 11.38829000000000136, 4.963071000000000232, 0.8648700000000000276 ) ) ; +#97141 = CARTESIAN_POINT ( 'NONE', ( 1.425641884052289976, -1.263266231710209908, 0.8300000000000022915 ) ) ; +#97142 = STYLED_ITEM ( 'NONE', ( #32817 ), #22683 ) ; +#97143 = EDGE_CURVE ( 'NONE', #72489, #2945, #36972, .T. ) ; +#97144 = LINE ( 'NONE', #4249, #36402 ) ; +#97145 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.500000000000000222, 0.1829999999999870064 ) ) ; +#97146 = PRESENTATION_STYLE_ASSIGNMENT (( #34421 ) ) ; +#97147 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #85723 ) ) ; +#97148 = AXIS2_PLACEMENT_3D ( 'NONE', #92889, #1025, #30125 ) ; +#97149 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999378, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#97150 = VERTEX_POINT ( 'NONE', #91577 ) ; +#97151 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 0.01000000000000000021, -0.4500000000000000666 ) ) ; +#97152 = AXIS2_PLACEMENT_3D ( 'NONE', #96440, #95937, #26046 ) ; +#97153 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97154 = STYLED_ITEM ( 'NONE', ( #75538 ), #13831 ) ; +#97155 = ORIENTED_EDGE ( 'NONE', *, *, #16157, .F. ) ; +#97156 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#97157 = SURFACE_STYLE_FILL_AREA ( #18564 ) ; +#97158 = PLANE ( 'NONE', #6625 ) ; +#97159 = CARTESIAN_POINT ( 'NONE', ( 1.624720795854639910, -0.9850088450568520448, 0.8100000000000000533 ) ) ; +#97160 = STYLED_ITEM ( 'NONE', ( #30691 ), #3816 ) ; +#97161 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.2999999999999990452, 0.1829999999999749605 ) ) ; +#97162 = CARTESIAN_POINT ( 'NONE', ( 0.2638348760318000030, -1.377348110544800219, 0.8100000000000000533 ) ) ; +#97163 = AXIS2_PLACEMENT_3D ( 'NONE', #80073, #80568, #9998 ) ; +#97164 = DIRECTION ( 'NONE', ( -0.3438200982495999147, 0.000000000000000000, 0.9390355371548169128 ) ) ; +#97165 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97166 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97167 = VERTEX_POINT ( 'NONE', #99160 ) ; +#97168 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#97169 = ADVANCED_FACE ( 'NONE', ( #52796 ), #100134, .F. ) ; +#97170 = FILL_AREA_STYLE ('',( #88539 ) ) ; +#97171 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.723820061220085131, -0.02000000000000000042 ) ) ; +#97172 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97173 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97174 = PRESENTATION_STYLE_ASSIGNMENT (( #98129 ) ) ; +#97175 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#97176 = PRESENTATION_STYLE_ASSIGNMENT (( #50780 ) ) ; +#97177 = PRESENTATION_STYLE_ASSIGNMENT (( #11352 ) ) ; +#97178 = AXIS2_PLACEMENT_3D ( 'NONE', #98831, #60166, #60645 ) ; +#97179 = SURFACE_STYLE_USAGE ( .BOTH. , #91547 ) ; +#97180 = PRESENTATION_STYLE_ASSIGNMENT (( #87540 ) ) ; +#97181 = PLANE ( 'NONE', #96858 ) ; +#97182 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 3.700000000000000178, 0.03429000000000000103 ) ) ; +#97183 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6344, 'distance_accuracy_value', 'NONE'); +#97184 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97185 = DIRECTION ( 'NONE', ( -0.7071067811865455743, 0.7071067811865493491, 0.000000000000000000 ) ) ; +#97186 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97187 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #98962, #33171 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #56492 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#97188 = ORIENTED_EDGE ( 'NONE', *, *, #67711, .T. ) ; +#97189 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#97190 = ORIENTED_EDGE ( 'NONE', *, *, #42071, .T. ) ; +#97191 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97192 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #68345, 'distance_accuracy_value', 'NONE'); +#97193 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61714, 'distance_accuracy_value', 'NONE'); +#97194 = SURFACE_STYLE_USAGE ( .BOTH. , #50304 ) ; +#97195 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2850000000000000311, -0.1458578643762690197 ) ) ; +#97196 = FACE_OUTER_BOUND ( 'NONE', #37485, .T. ) ; +#97197 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97198 = AXIS2_PLACEMENT_3D ( 'NONE', #89032, #80378, #43548 ) ; +#97199 = AXIS2_PLACEMENT_3D ( 'NONE', #92870, #84261, #91414 ) ; +#97200 = CARTESIAN_POINT ( 'NONE', ( -0.1591923701298699478, 0.7099999999999999645, -1.016439536705160407E-17 ) ) ; +#97201 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#97202 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97203 = VERTEX_POINT ( 'NONE', #46613 ) ; +#97205 = FILL_AREA_STYLE ('',( #3799 ) ) ; +#97204 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97206 = SURFACE_SIDE_STYLE ('',( #66098 ) ) ; +#97207 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25693, 'distance_accuracy_value', 'NONE'); +#97208 = VECTOR ( 'NONE', #16613, 1000.000000000000000 ) ; +#97209 = VECTOR ( 'NONE', #1860, 1000.000000000000000 ) ; +#97210 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98146 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76019, #58237, #89833 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97211 = VERTEX_POINT ( 'NONE', #7241 ) ; +#97212 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, 3.149999999999999911, 0.000000000000000000 ) ) ; +#97213 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97214 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97215 = CARTESIAN_POINT ( 'NONE', ( -1.175156004799000176, -1.443574297695930264, 0.8100000000000000533 ) ) ; +#97216 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.008431457505076156086, -0.1458578643762691029 ) ) ; +#97217 = ORIENTED_EDGE ( 'NONE', *, *, #39263, .F. ) ; +#97218 = EDGE_CURVE ( 'NONE', #8528, #63754, #157, .T. ) ; +#97219 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #9343, 'distance_accuracy_value', 'NONE'); +#97220 = SURFACE_STYLE_USAGE ( .BOTH. , #96709 ) ; +#97221 = SURFACE_SIDE_STYLE ('',( #51804 ) ) ; +#97222 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999689, -2.000000000000000000, 0.000000000000000000 ) ) ; +#97223 = VERTEX_POINT ( 'NONE', #40505 ) ; +#97224 = VECTOR ( 'NONE', #93371, 1000.000000000000000 ) ; +#97225 = VECTOR ( 'NONE', #70199, 1000.000000000000000 ) ; +#97226 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97227 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97228 = PLANE ( 'NONE', #36413 ) ; +#97229 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97230 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 0.6999999999999999556, -13.35000000000000142 ) ) ; +#97231 = VERTEX_POINT ( 'NONE', #70609 ) ; +#97232 = FILL_AREA_STYLE_COLOUR ( '', #22075 ) ; +#97233 = AXIS2_PLACEMENT_3D ( 'NONE', #36711, #90822, #45322 ) ; +#97234 = ADVANCED_FACE ( 'NONE', ( #32830 ), #71124, .T. ) ; +#97235 = STYLED_ITEM ( 'NONE', ( #36530 ), #4339 ) ; +#97236 = ORIENTED_EDGE ( 'NONE', *, *, #78609, .F. ) ; +#97238 = VERTEX_POINT ( 'NONE', #9255 ) ; +#97237 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97239 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #16949 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50340, #50826, #73295 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97240 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#97241 = CARTESIAN_POINT ( 'NONE', ( 9.974076999999999416, 3.548858000000000068, 0.8991599999999999593 ) ) ; +#97242 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.004999999999999999237, 0.1500000000000000222 ) ) ; +#97243 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 0.4600000000000000200, -1.100000000000000089 ) ) ; +#97244 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#97245 = ORIENTED_EDGE ( 'NONE', *, *, #61286, .F. ) ; +#97246 = SURFACE_SIDE_STYLE ('',( #43632 ) ) ; +#97247 = LINE ( 'NONE', #75664, #42510 ) ; +#97248 = CARTESIAN_POINT ( 'NONE', ( -0.1150130133853430603, 0.2193340759269652163, 0.8100000000000000533 ) ) ; +#97249 = ORIENTED_EDGE ( 'NONE', *, *, #58416, .T. ) ; +#97250 = CIRCLE ( 'NONE', #27197, 0.009999999999999998473 ) ; +#97251 = CARTESIAN_POINT ( 'NONE', ( 1.800000000000000266, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#97252 = ORIENTED_EDGE ( 'NONE', *, *, #35543, .F. ) ; +#97253 = EDGE_CURVE ( 'NONE', #2598, #66369, #32330, .T. ) ; +#97255 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97254 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97256 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97257 = VERTEX_POINT ( 'NONE', #659 ) ; +#97258 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62112, #99285, #21759, #45212, #100252, #93174, #29430, #100749, #60595, #52925, #38593, #46734, #45704, #84057, #76378, #91211, #67704, #83559, #6380 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.289444789457616286E-05, 2.549973415362012351E-05, 3.801561174744482298E-05, 5.040511403747406020E-05, 6.264100167992574209E-05, 7.454698067566952358E-05, 8.605472911503915013E-05, 9.753033114700983394E-05, 0.0001088881519317706228, 0.0001202550761410757507, 0.0001315881507700778744, 0.0001431828865404786955, 0.0001550584193850461324, 0.0001670638921105368471, 0.0001793942156805940007, 0.0001922938194067753525 ), + .UNSPECIFIED. ) ; +#97259 = FILL_AREA_STYLE ('',( #89133 ) ) ; +#97260 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40239 ), #2771 ) ; +#97261 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97262 = ORIENTED_EDGE ( 'NONE', *, *, #90739, .T. ) ; +#97263 = ORIENTED_EDGE ( 'NONE', *, *, #96692, .T. ) ; +#97264 = LINE ( 'NONE', #99209, #82976 ) ; +#97265 = ADVANCED_FACE ( 'NONE', ( #22651 ), #48154, .T. ) ; +#97267 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97266 = FILL_AREA_STYLE_COLOUR ( '', #59179 ) ; +#97268 = CARTESIAN_POINT ( 'NONE', ( -1.014711377400389969, -1.276477384597439979, 0.8299999999999999600 ) ) ; +#97269 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66332 ) ) ; +#97270 = FILL_AREA_STYLE ('',( #98225 ) ) ; +#97271 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81068 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26735, #19035, #82356 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97272 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999950173, -2.100000000000000089, 0.000000000000000000 ) ) ; +#97273 = VECTOR ( 'NONE', #29350, 999.9999999999998863 ) ; +#97274 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97275 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97276 = CARTESIAN_POINT ( 'NONE', ( -0.1238200612200840572, 3.099999999999980105, 0.000000000000000000 ) ) ; +#97277 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97278 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #100451 ) ) ; +#97279 = VERTEX_POINT ( 'NONE', #7731 ) ; +#97280 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97281 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97282 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #45847 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15914, #15406, #78244 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97285 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97284 = CYLINDRICAL_SURFACE ( 'NONE', #11428, 0.09999999999999939493 ) ; +#97283 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.1499999999999999667, 0.2100000000000000200 ) ) ; +#97286 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999948486, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#97287 = LINE ( 'NONE', #88645, #60974 ) ; +#97288 = VECTOR ( 'NONE', #55033, 1000.000000000000000 ) ; +#97289 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97290 = SURFACE_SIDE_STYLE ('',( #98241 ) ) ; +#97291 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.23504400000000025, 0.8648700000000000276 ) ) ; +#97292 = VERTEX_POINT ( 'NONE', #78776 ) ; +#97293 = EDGE_CURVE ( 'NONE', #33242, #47283, #79292, .T. ) ; +#97294 = STYLED_ITEM ( 'NONE', ( #37182 ), #39664 ) ; +#97295 = VECTOR ( 'NONE', #36457, 1000.000000000000000 ) ; +#97296 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, 0.2750000000000000222, 0.1499999999999999667 ) ) ; +#97297 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97298 = FACE_OUTER_BOUND ( 'NONE', #79725, .T. ) ; +#97299 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 12.49601200000000034, 0.8648700000000000276 ) ) ; +#97300 = FILL_AREA_STYLE ('',( #95793 ) ) ; +#97301 = STYLED_ITEM ( 'NONE', ( #33892 ), #14267 ) ; +#97302 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97303 = CARTESIAN_POINT ( 'NONE', ( -1.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#97304 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97305 = LINE ( 'NONE', #44200, #79620 ) ; +#97306 = PRESENTATION_STYLE_ASSIGNMENT (( #96804 ) ) ; +#97307 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97308 = CARTESIAN_POINT ( 'NONE', ( 1.785976973916959976, -1.116141175150469955, 0.8299999999999997380 ) ) ; +#97309 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #44262, 'design' ) ; +#97310 = LINE ( 'NONE', #79659, #85725 ) ; +#97311 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 2.000000000000000000, 0.03429000000000000103 ) ) ; +#97312 = CARTESIAN_POINT ( 'NONE', ( -0.01000000000000000021, 0.3966667321250390010, 0.6832601347701363625 ) ) ; +#97313 = EDGE_CURVE ( 'NONE', #94979, #60384, #23162, .T. ) ; +#97314 = ORIENTED_EDGE ( 'NONE', *, *, #7042, .F. ) ; +#97315 = CARTESIAN_POINT ( 'NONE', ( 5.924999999999999822, 0.2000000000000000111, -13.40000000000000036 ) ) ; +#97316 = EDGE_CURVE ( 'NONE', #88355, #83662, #10242, .T. ) ; +#97317 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #36929, 'distance_accuracy_value', 'NONE'); +#97318 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61129, 'distance_accuracy_value', 'NONE'); +#97320 = LINE ( 'NONE', #36096, #12762 ) ; +#97319 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97321 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59863 ), #67945 ) ; +#97322 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.649999999999999911, 0.000000000000000000 ) ) ; +#97323 = FACE_OUTER_BOUND ( 'NONE', #65989, .T. ) ; +#97324 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98986 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #18295, #58674, #65289 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97325 = VERTEX_POINT ( 'NONE', #33855 ) ; +#97326 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 10.95742000000000083, 0.8648700000000000276 ) ) ; +#97327 = CARTESIAN_POINT ( 'NONE', ( -1.479999999999999982, 0.4600000000000000200, 1.250000000000000000 ) ) ; +#97328 = EDGE_CURVE ( 'NONE', #55685, #98421, #64975, .T. ) ; +#97329 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #54420, 'distance_accuracy_value', 'NONE'); +#97331 = FILL_AREA_STYLE_COLOUR ( '', #99882 ) ; +#97330 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97332 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #20760 ) ) ; +#97333 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #83115, 'distance_accuracy_value', 'NONE'); +#97334 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97335 = ORIENTED_EDGE ( 'NONE', *, *, #98328, .T. ) ; +#97336 = EDGE_LOOP ( 'NONE', ( #53927, #21768, #5661, #71656, #78046 ) ) ; +#97337 = ORIENTED_EDGE ( 'NONE', *, *, #4634, .T. ) ; +#97338 = CARTESIAN_POINT ( 'NONE', ( 0.2416038136213350396, -1.101447087279459947, 0.8299999999999996270 ) ) ; +#97339 = AXIS2_PLACEMENT_3D ( 'NONE', #21564, #69514, #84360 ) ; +#97340 = FACE_OUTER_BOUND ( 'NONE', #3913, .T. ) ; +#97341 = FILL_AREA_STYLE_COLOUR ( '', #77772 ) ; +#97342 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999969891, 0.000000000000000000 ) ) ; +#97343 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#97344 = EDGE_CURVE ( 'NONE', #84398, #87098, #18494, .T. ) ; +#97345 = FILL_AREA_STYLE_COLOUR ( '', #3662 ) ; +#97347 = ORIENTED_EDGE ( 'NONE', *, *, #72821, .T. ) ; +#97346 = ORIENTED_EDGE ( 'NONE', *, *, #66446, .F. ) ; +#97348 = VECTOR ( 'NONE', #73493, 1000.000000000000000 ) ; +#97349 = EDGE_LOOP ( 'NONE', ( #80262, #51772, #57876, #81354 ) ) ; +#97350 = VERTEX_POINT ( 'NONE', #96086 ) ; +#97351 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97352 = VECTOR ( 'NONE', #99722, 1000.000000000000000 ) ; +#97353 = VECTOR ( 'NONE', #86954, 1000.000000000000000 ) ; +#97354 = FILL_AREA_STYLE_COLOUR ( '', #8198 ) ; +#97355 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74594 ), #43518 ) ; +#97357 = PRESENTATION_STYLE_ASSIGNMENT (( #43259 ) ) ; +#97356 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.299999999999999822, -0.02000000000000000042 ) ) ; +#97358 = VERTEX_POINT ( 'NONE', #3193 ) ; +#97359 = CLOSED_SHELL ( 'NONE', ( #75496, #5647, #7529, #390, #86479, #56643, #72097, #76469, #13344, #35310, #3899, #85698, #49391, #96803, #85088, #63091, #73143, #5455, #39664, #78312, #80901, #76969, #33908, #61377, #85067, #1598, #54391, #68730, #86168, #50933, #75901, #43735, #6497, #69631, #26829, #43846, #12691, #87261, #94753, #23270, #46537, #53172, #66216, #2492 ) ) ; +#97360 = AXIS2_PLACEMENT_3D ( 'NONE', #67648, #75337, #10959 ) ; +#97361 = LINE ( 'NONE', #12040, #22900 ) ; +#97362 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.100000000000000311, 1.048695503451053346E-76 ) ) ; +#97363 = ORIENTED_EDGE ( 'NONE', *, *, #85029, .F. ) ; +#97365 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97364 = PRESENTATION_STYLE_ASSIGNMENT (( #35147 ) ) ; +#97366 = ORIENTED_EDGE ( 'NONE', *, *, #72108, .F. ) ; +#97367 = VERTEX_POINT ( 'NONE', #64479 ) ; +#97368 = FILL_AREA_STYLE_COLOUR ( '', #2145 ) ; +#97369 = VECTOR ( 'NONE', #91871, 1000.000000000000000 ) ; +#97370 = EDGE_CURVE ( 'NONE', #93065, #61237, #2197, .T. ) ; +#97372 = PRESENTATION_STYLE_ASSIGNMENT (( #57641 ) ) ; +#97371 = SURFACE_STYLE_USAGE ( .BOTH. , #45246 ) ; +#97373 = FACE_OUTER_BOUND ( 'NONE', #86606, .T. ) ; +#97374 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97375 = EDGE_LOOP ( 'NONE', ( #44275, #38109, #22018, #14701 ) ) ; +#97376 = ORIENTED_EDGE ( 'NONE', *, *, #100083, .F. ) ; +#97377 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#97378 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97379 = ORIENTED_EDGE ( 'NONE', *, *, #44614, .T. ) ; +#97380 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8099999999999416556 ) ) ; +#97381 = ORIENTED_EDGE ( 'NONE', *, *, #7069, .T. ) ; +#97382 = ORIENTED_EDGE ( 'NONE', *, *, #29469, .T. ) ; +#97383 = EDGE_CURVE ( 'NONE', #74029, #31354, #73644, .T. ) ; +#97384 = CARTESIAN_POINT ( 'NONE', ( 0.4915531961084259605, -0.9443244458491719673, 0.8299999999999992939 ) ) ; +#97385 = FILL_AREA_STYLE ('',( #12582 ) ) ; +#97386 = FILL_AREA_STYLE_COLOUR ( '', #7231 ) ; +#97387 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97388 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990585, 1.300000000000000044, 1.048695503451051965E-76 ) ) ; +#97389 = EDGE_CURVE ( 'NONE', #69445, #75309, #41502, .T. ) ; +#97390 = VECTOR ( 'NONE', #29857, 999.9999999999998863 ) ; +#97391 = CARTESIAN_POINT ( 'NONE', ( 13.48093599999999981, 6.352400000000000269, 0.8648700000000000276 ) ) ; +#97392 = SURFACE_STYLE_FILL_AREA ( #66774 ) ; +#97393 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #90930 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #36683, #91759, #84127 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97394 = VERTEX_POINT ( 'NONE', #74151 ) ; +#97395 = ORIENTED_EDGE ( 'NONE', *, *, #97986, .T. ) ; +#97396 = FILL_AREA_STYLE ('',( #98843 ) ) ; +#97397 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#97398 = CARTESIAN_POINT ( 'NONE', ( 1.441396927522579974, -1.330101555947649894, 0.8100000000000000533 ) ) ; +#97399 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97400 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6367 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #87535, #17067, #17560 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97401 = SURFACE_STYLE_USAGE ( .BOTH. , #50511 ) ; +#97402 = FACE_OUTER_BOUND ( 'NONE', #30830, .T. ) ; +#97403 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#97404 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 7.950000000000000178, 0.000000000000000000 ) ) ; +#97405 = LINE ( 'NONE', #4497, #59823 ) ; +#97406 = SURFACE_STYLE_USAGE ( .BOTH. , #10066 ) ; +#97408 = VERTEX_POINT ( 'NONE', #56846 ) ; +#97407 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97409 = CARTESIAN_POINT ( 'NONE', ( 0.2602179779670369952, -0.9240726320973919883, 0.8100000000000000533 ) ) ; +#97410 = FILL_AREA_STYLE_COLOUR ( '', #10109 ) ; +#97411 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.1238200612200849871, 0.000000000000000000 ) ) ; +#97412 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.366666666666666696, 0.000000000000000000 ) ) ; +#97413 = AXIS2_PLACEMENT_3D ( 'NONE', #86618, #7417, #94751 ) ; +#97414 = CARTESIAN_POINT ( 'NONE', ( 1.433730380350167533, -1.395329896795625357, 0.8099999999997412603 ) ) ; +#97415 = SURFACE_SIDE_STYLE ('',( #81154 ) ) ; +#97416 = EDGE_CURVE ( 'NONE', #74502, #61880, #96589, .T. ) ; +#97417 = VECTOR ( 'NONE', #20792, 999.9999999999998863 ) ; +#97418 = SURFACE_STYLE_USAGE ( .BOTH. , #59710 ) ; +#97419 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97421 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97420 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97422 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#97423 = VECTOR ( 'NONE', #86664, 1000.000000000000000 ) ; +#97424 = SURFACE_STYLE_USAGE ( .BOTH. , #58195 ) ; +#97425 = AXIS2_PLACEMENT_3D ( 'NONE', #77226, #77742, #21608 ) ; +#97426 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97427 = AXIS2_PLACEMENT_3D ( 'NONE', #15174, #70871, #7982 ) ; +#97428 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28189, 'distance_accuracy_value', 'NONE'); +#97429 = ORIENTED_EDGE ( 'NONE', *, *, #47513, .F. ) ; +#97430 = CLOSED_SHELL ( 'NONE', ( #27179, #95169, #91918, #85236, #63340, #42210 ) ) ; +#97431 = CARTESIAN_POINT ( 'NONE', ( 3.256562999999999874, 5.090351000000000070, 0.8991599999999999593 ) ) ; +#97432 = FILL_AREA_STYLE ('',( #73496 ) ) ; +#97433 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97434 = ADVANCED_FACE ( 'NONE', ( #56354 ), #48670, .T. ) ; +#97435 = ORIENTED_EDGE ( 'NONE', *, *, #15057, .T. ) ; +#97436 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.000000000000000000 ) ) ; +#97438 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #67992 ), #69741 ) ; +#97437 = FACE_OUTER_BOUND ( 'NONE', #6017, .T. ) ; +#97439 = LINE ( 'NONE', #89804, #86055 ) ; +#97440 = EDGE_CURVE ( 'NONE', #71148, #12557, #88455, .T. ) ; +#97441 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97442 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.258441558441560026, 0.8299999999999999600 ) ) ; +#97443 = STYLED_ITEM ( 'NONE', ( #98476 ), #50404 ) ; +#97444 = EDGE_CURVE ( 'NONE', #4959, #77419, #73150, .T. ) ; +#97445 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155850987, 0.8100000000000249223 ) ) ; +#97446 = VERTEX_POINT ( 'NONE', #72141 ) ; +#97447 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #80936 ), #40432 ) ; +#97448 = EDGE_LOOP ( 'NONE', ( #78249, #43988, #3723, #84310 ) ) ; +#97449 = FILL_AREA_STYLE ('',( #66343 ) ) ; +#97450 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97451 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98981 ) ) ; +#97452 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.7000000000000005107, -0.02000000000000000042 ) ) ; +#97453 = CARTESIAN_POINT ( 'NONE', ( -0.4484724165379589955, -1.115587024626630175, 0.8100000000000000533 ) ) ; +#97454 = EDGE_CURVE ( 'NONE', #85903, #9382, #98043, .T. ) ; +#97455 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45931, 'distance_accuracy_value', 'NONE'); +#97456 = CARTESIAN_POINT ( 'NONE', ( -0.009999999999999975922, 0.2500000000000000555, 0.5799137866959191978 ) ) ; +#97457 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97458 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #88674, 'distance_accuracy_value', 'NONE'); +#97459 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97460 = SURFACE_STYLE_USAGE ( .BOTH. , #64840 ) ; +#97461 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97462 = ORIENTED_EDGE ( 'NONE', *, *, #6087, .F. ) ; +#97463 = EDGE_CURVE ( 'NONE', #35131, #69209, #19512, .T. ) ; +#97464 = AXIS2_PLACEMENT_3D ( 'NONE', #86828, #18362, #48028 ) ; +#97465 = FILL_AREA_STYLE ('',( #34235 ) ) ; +#97466 = VERTEX_POINT ( 'NONE', #21513 ) ; +#97467 = LINE ( 'NONE', #37242, #87694 ) ; +#97468 = CARTESIAN_POINT ( 'NONE', ( -1.066869350290160279, -0.9766832120545909657, 0.8299999999999999600 ) ) ; +#97469 = EDGE_CURVE ( 'NONE', #58131, #30759, #44473, .T. ) ; +#97470 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97471 = LINE ( 'NONE', #19896, #79054 ) ; +#97472 = EDGE_CURVE ( 'NONE', #70921, #87853, #60854, .T. ) ; +#97474 = EDGE_LOOP ( 'NONE', ( #81086, #12010, #19287, #49102 ) ) ; +#97473 = ORIENTED_EDGE ( 'NONE', *, *, #84489, .F. ) ; +#97475 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97476 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94723 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #24326, #56982, #2340 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97477 = ORIENTED_EDGE ( 'NONE', *, *, #98830, .F. ) ; +#97478 = SURFACE_STYLE_USAGE ( .BOTH. , #95974 ) ; +#97479 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89414 ) ) ; +#97480 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35590 ), #22495 ) ; +#97482 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97481 = CARTESIAN_POINT ( 'NONE', ( 10.20742199999999933, 4.701442000000000121, 0.8991599999999999593 ) ) ; +#97483 = ORIENTED_EDGE ( 'NONE', *, *, #85411, .T. ) ; +#97484 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97485 = ORIENTED_EDGE ( 'NONE', *, *, #37032, .T. ) ; +#97486 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, -0.1499999999999999667, 0.2100000000000000200 ) ) ; +#97487 = FACE_OUTER_BOUND ( 'NONE', #39837, .T. ) ; +#97488 = SURFACE_STYLE_FILL_AREA ( #74040 ) ; +#97489 = AXIS2_PLACEMENT_3D ( 'NONE', #34419, #95129, #34917 ) ; +#97490 = FILL_AREA_STYLE_COLOUR ( '', #62958 ) ; +#97491 = DIRECTION ( 'NONE', ( -0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#97492 = ORIENTED_EDGE ( 'NONE', *, *, #95123, .T. ) ; +#97493 = ORIENTED_EDGE ( 'NONE', *, *, #68279, .F. ) ; +#97494 = SURFACE_STYLE_USAGE ( .BOTH. , #35278 ) ; +#97495 = ORIENTED_EDGE ( 'NONE', *, *, #28278, .F. ) ; +#97496 = SURFACE_STYLE_USAGE ( .BOTH. , #11657 ) ; +#97497 = AXIS2_PLACEMENT_3D ( 'NONE', #43638, #28347, #34526 ) ; +#97498 = EDGE_CURVE ( 'NONE', #30306, #94706, #82322, .T. ) ; +#97499 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #75332 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21981, #90934, #43459 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97500 = STYLED_ITEM ( 'NONE', ( #43301 ), #745 ) ; +#97502 = VERTEX_POINT ( 'NONE', #51688 ) ; +#97501 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97503 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, -0.3000000000000016542, 7.103537399566374497E-79 ) ) ; +#97505 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74339 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70228, #287, #23797 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97504 = LINE ( 'NONE', #27613, #65211 ) ; +#97506 = ORIENTED_EDGE ( 'NONE', *, *, #90568, .T. ) ; +#97507 = CLOSED_SHELL ( 'NONE', ( #46912, #78771, #48846, #78695, #36790, #67427 ) ) ; +#97508 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97509 = ORIENTED_EDGE ( 'NONE', *, *, #74286, .F. ) ; +#97510 = EDGE_LOOP ( 'NONE', ( #1575, #49960, #67799, #14345 ) ) ; +#97511 = EDGE_CURVE ( 'NONE', #29762, #46959, #12785, .T. ) ; +#97512 = SURFACE_STYLE_FILL_AREA ( #82726 ) ; +#97513 = CARTESIAN_POINT ( 'NONE', ( 6.927800000000000402, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#97514 = PLANE ( 'NONE', #90524 ) ; +#97515 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97516 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000004913, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#97517 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97518 = ADVANCED_FACE ( 'NONE', ( #20510 ), #66975, .F. ) ; +#97519 = PLANE ( 'NONE', #2164 ) ; +#97520 = STYLED_ITEM ( 'NONE', ( #81668 ), #15001 ) ; +#97521 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#97523 = LINE ( 'NONE', #27631, #74310 ) ; +#97522 = FILL_AREA_STYLE_COLOUR ( '', #7248 ) ; +#97524 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#97525 = ORIENTED_EDGE ( 'NONE', *, *, #9400, .F. ) ; +#97526 = PRESENTATION_STYLE_ASSIGNMENT (( #74074 ) ) ; +#97527 = VERTEX_POINT ( 'NONE', #37368 ) ; +#97528 = FILL_AREA_STYLE ('',( #88900 ) ) ; +#97529 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97530 = VECTOR ( 'NONE', #26673, 1000.000000000000000 ) ; +#97531 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97532 = CARTESIAN_POINT ( 'NONE', ( -0.4387205553799810032, -1.232805253472390117, 0.8300000000000000711 ) ) ; +#97533 = SURFACE_SIDE_STYLE ('',( #36297 ) ) ; +#97534 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97535 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97536 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32910, #32410, #93126, #48751 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97537 = SURFACE_STYLE_USAGE ( .BOTH. , #19462 ) ; +#97538 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #98991 ) ) ; +#97539 = AXIS2_PLACEMENT_3D ( 'NONE', #40845, #9596, #15806 ) ; +#97540 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #9445 ), #86110 ) ; +#97541 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97542 = ADVANCED_FACE ( 'NONE', ( #90969 ), #35864, .F. ) ; +#97543 = EDGE_CURVE ( 'NONE', #38496, #97350, #98049, .T. ) ; +#97544 = ORIENTED_EDGE ( 'NONE', *, *, #12257, .T. ) ; +#97545 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #73089 ), #51892 ) ; +#97547 = PRESENTATION_STYLE_ASSIGNMENT (( #11212 ) ) ; +#97546 = PRESENTATION_STYLE_ASSIGNMENT (( #4629 ) ) ; +#97548 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97549 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61669 ), #63360 ) ; +#97550 = STYLED_ITEM ( 'NONE', ( #100603 ), #84758 ) ; +#97551 = VECTOR ( 'NONE', #62832, 1000.000000000000000 ) ; +#97552 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #45791, 'distance_accuracy_value', 'NONE'); +#97553 = ORIENTED_EDGE ( 'NONE', *, *, #42045, .F. ) ; +#97554 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97555 = AXIS2_PLACEMENT_3D ( 'NONE', #13003, #74874, #21239 ) ; +#97556 = LINE ( 'NONE', #33810, #40783 ) ; +#97557 = CARTESIAN_POINT ( 'NONE', ( 2.149999999999999911, 3.099999999999969891, 0.000000000000000000 ) ) ; +#97558 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#97559 = EDGE_CURVE ( 'NONE', #72729, #9248, #54701, .T. ) ; +#97560 = STYLED_ITEM ( 'NONE', ( #95517 ), #79933 ) ; +#97561 = STYLED_ITEM ( 'NONE', ( #61280 ), #17647 ) ; +#97562 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#97563 = ORIENTED_EDGE ( 'NONE', *, *, #74135, .F. ) ; +#97564 = EDGE_LOOP ( 'NONE', ( #47657, #55962, #99753, #61635 ) ) ; +#97565 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33999 ) ) ; +#97566 = FILL_AREA_STYLE_COLOUR ( '', #24259 ) ; +#97567 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #77682, 'distance_accuracy_value', 'NONE'); +#97568 = PLANE ( 'NONE', #20255 ) ; +#97569 = PRESENTATION_STYLE_ASSIGNMENT (( #58341 ) ) ; +#97570 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97571 = LINE ( 'NONE', #74131, #33795 ) ; +#97572 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97573 = ORIENTED_EDGE ( 'NONE', *, *, #8599, .T. ) ; +#97574 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.123820061220045297, -0.02000000000000000042 ) ) ; +#97575 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97576 = ORIENTED_EDGE ( 'NONE', *, *, #82957, .F. ) ; +#97577 = VERTEX_POINT ( 'NONE', #86314 ) ; +#97578 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86935 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #26505, #73966, #57680 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97579 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40575 ), #50368 ) ; +#97580 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97581 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#97582 = CARTESIAN_POINT ( 'NONE', ( 0.2958578643762690419, -0.01500000000000001506, -0.1400000000000000411 ) ) ; +#97583 = DIRECTION ( 'NONE', ( 0.9408821649279537347, 0.000000000000000000, -0.3387340427540269649 ) ) ; +#97584 = EDGE_CURVE ( 'NONE', #89943, #20794, #87092, .T. ) ; +#97585 = VERTEX_POINT ( 'NONE', #23045 ) ; +#97586 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.09999999999999996392, -0.02000000000001464842 ) ) ; +#97587 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #54306, #63502, #70106, #92566 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97588 = SURFACE_STYLE_USAGE ( .BOTH. , #67464 ) ; +#97589 = ORIENTED_EDGE ( 'NONE', *, *, #60063, .T. ) ; +#97590 = ORIENTED_EDGE ( 'NONE', *, *, #44444, .T. ) ; +#97591 = VERTEX_POINT ( 'NONE', #62356 ) ; +#97592 = CARTESIAN_POINT ( 'NONE', ( 1.726111644763860253, -0.9656914468017120390, 0.8300000000000004041 ) ) ; +#97593 = SURFACE_STYLE_FILL_AREA ( #17986 ) ; +#97594 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#97595 = STYLED_ITEM ( 'NONE', ( #97364 ), #75119 ) ; +#97597 = CARTESIAN_POINT ( 'NONE', ( 0.2800000000000000266, 0.1499999999999999944, 0.000000000000000000 ) ) ; +#97596 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#97598 = ORIENTED_EDGE ( 'NONE', *, *, #31160, .F. ) ; +#97600 = VERTEX_POINT ( 'NONE', #78647 ) ; +#97599 = ORIENTED_EDGE ( 'NONE', *, *, #92383, .F. ) ; +#97601 = ORIENTED_EDGE ( 'NONE', *, *, #33848, .T. ) ; +#97602 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81053 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14678, #43857, #99391 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97603 = EDGE_CURVE ( 'NONE', #32170, #59719, #47007, .T. ) ; +#97604 = ORIENTED_EDGE ( 'NONE', *, *, #60076, .F. ) ; +#97605 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97606 = ORIENTED_EDGE ( 'NONE', *, *, #99755, .F. ) ; +#97607 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #84590 ) ) ; +#97608 = AXIS2_PLACEMENT_3D ( 'NONE', #56453, #8341, #24803 ) ; +#97609 = FILL_AREA_STYLE ('',( #82840 ) ) ; +#97610 = ORIENTED_EDGE ( 'NONE', *, *, #16344, .T. ) ; +#97611 = PRESENTATION_STYLE_ASSIGNMENT (( #83351 ) ) ; +#97612 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 5.557041000000000786, 0.8991599999999999593 ) ) ; +#97613 = VERTEX_POINT ( 'NONE', #8616 ) ; +#97614 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #51984 ), #65016 ) ; +#97615 = EDGE_CURVE ( 'NONE', #43011, #41436, #69461, .T. ) ; +#97616 = AXIS2_PLACEMENT_3D ( 'NONE', #70876, #47385, #16205 ) ; +#97617 = CARTESIAN_POINT ( 'NONE', ( 0.9000000000000010214, 3.123820061220065281, 0.000000000000000000 ) ) ; +#97618 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#97619 = VECTOR ( 'NONE', #71447, 1000.000000000000000 ) ; +#97620 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97621 = PLANE ( 'NONE', #51015 ) ; +#97622 = STYLED_ITEM ( 'NONE', ( #34166 ), #17785 ) ; +#97623 = PLANE ( 'NONE', #21010 ) ; +#97625 = CARTESIAN_POINT ( 'NONE', ( 1.496184376687780260, -1.336216925617480067, 0.8299999999999999600 ) ) ; +#97624 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97626 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #22593 ) ) ; +#97627 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97628 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #6273 ) ) ; +#97629 = ORIENTED_EDGE ( 'NONE', *, *, #61994, .T. ) ; +#97630 = ADVANCED_FACE ( 'NONE', ( #100497 ), #93928, .T. ) ; +#97631 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97632 = PRESENTATION_STYLE_ASSIGNMENT (( #74706 ) ) ; +#97633 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #50427 ), #91190 ) ; +#97634 = EDGE_CURVE ( 'NONE', #5920, #2068, #96819, .T. ) ; +#97636 = FILL_AREA_STYLE_COLOUR ( '', #24712 ) ; +#97635 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97637 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97638 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000444, -3.266666666666639962, 0.000000000000000000 ) ) ; +#97639 = SURFACE_SIDE_STYLE ('',( #37909 ) ) ; +#97640 = AXIS2_PLACEMENT_3D ( 'NONE', #98598, #58931, #82391 ) ; +#97641 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999999237, 0.1458578643762690752 ) ) ; +#97642 = EDGE_LOOP ( 'NONE', ( #43407, #81402, #8361, #66623, #23163, #63402, #93994, #38657 ) ) ; +#97643 = SURFACE_STYLE_USAGE ( .BOTH. , #27769 ) ; +#97644 = EDGE_CURVE ( 'NONE', #9533, #32201, #59091, .T. ) ; +#97645 = FILL_AREA_STYLE ('',( #58926 ) ) ; +#97646 = STYLED_ITEM ( 'NONE', ( #81926 ), #15348 ) ; +#97647 = ORIENTED_EDGE ( 'NONE', *, *, #7448, .T. ) ; +#97648 = PRESENTATION_STYLE_ASSIGNMENT (( #59436 ) ) ; +#97649 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, -1.899999999999999911, -0.02000000000000000042 ) ) ; +#97650 = CARTESIAN_POINT ( 'NONE', ( 1.639423674598250003, -1.436594792639700247, 0.8099999999999976108 ) ) ; +#97651 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97652 = EDGE_CURVE ( 'NONE', #3712, #88330, #46483, .T. ) ; +#97653 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97654 = CARTESIAN_POINT ( 'NONE', ( 0.2000000000000000111, -8.400000000000000355, -11.36999999999999922 ) ) ; +#97655 = EDGE_LOOP ( 'NONE', ( #58373, #69358, #10024, #86486 ) ) ; +#97656 = SURFACE_SIDE_STYLE ('',( #89551 ) ) ; +#97657 = SURFACE_STYLE_FILL_AREA ( #57941 ) ; +#97658 = SURFACE_SIDE_STYLE ('',( #73721 ) ) ; +#97659 = CARTESIAN_POINT ( 'NONE', ( 1.033493568211090174, -0.9379159637996601351, 0.8299999999999994049 ) ) ; +#97660 = EDGE_CURVE ( 'NONE', #90226, #47424, #65345, .T. ) ; +#97661 = CARTESIAN_POINT ( 'NONE', ( -0.01448863636363688888, -1.186891233766236731, 0.8099999999999668576 ) ) ; +#97662 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#97663 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#97664 = PRESENTATION_STYLE_ASSIGNMENT (( #36934 ) ) ; +#97665 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#97666 = ADVANCED_FACE ( 'NONE', ( #3581 ), #19389, .T. ) ; +#97667 = PLANE ( 'NONE', #55784 ) ; +#97668 = SURFACE_STYLE_FILL_AREA ( #34951 ) ; +#97669 = FILL_AREA_STYLE_COLOUR ( '', #73204 ) ; +#97670 = ORIENTED_EDGE ( 'NONE', *, *, #58670, .F. ) ; +#97671 = ORIENTED_EDGE ( 'NONE', *, *, #20029, .T. ) ; +#97672 = SURFACE_STYLE_FILL_AREA ( #42603 ) ; +#97673 = CARTESIAN_POINT ( 'NONE', ( 7.944681000000000104, 2.438701000000000008, 0.8991599999999999593 ) ) ; +#97674 = FACE_OUTER_BOUND ( 'NONE', #20200, .T. ) ; +#97675 = STYLED_ITEM ( 'NONE', ( #85045 ), #85198 ) ; +#97676 = STYLED_ITEM ( 'NONE', ( #34849 ), #92267 ) ; +#97677 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#97678 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97679 = CARTESIAN_POINT ( 'NONE', ( 5.400000000000000355, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#97680 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97681 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#97682 = ORIENTED_EDGE ( 'NONE', *, *, #27592, .T. ) ; +#97683 = VECTOR ( 'NONE', #84929, 1000.000000000000000 ) ; +#97684 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 12.19999999999999929, 0.000000000000000000 ) ) ; +#97685 = PLANE ( 'NONE', #69952 ) ; +#97686 = ORIENTED_EDGE ( 'NONE', *, *, #25307, .T. ) ; +#97687 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97688 = CARTESIAN_POINT ( 'NONE', ( 1.329279248099940025, -1.493640573211080014, 0.8299999999999994049 ) ) ; +#97689 = VECTOR ( 'NONE', #92307, 1000.000000000000000 ) ; +#97690 = PRESENTATION_STYLE_ASSIGNMENT (( #13394 ) ) ; +#97691 = CARTESIAN_POINT ( 'NONE', ( -1.316306714908529907, -1.318596846191909977, 0.8100000000000000533 ) ) ; +#97692 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999988828, -0.1400000000000000411 ) ) ; +#97693 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70026 ) ) ; +#97694 = EDGE_CURVE ( 'NONE', #90329, #92247, #27081, .T. ) ; +#97695 = ORIENTED_EDGE ( 'NONE', *, *, #24396, .F. ) ; +#97696 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97697 = PRESENTATION_STYLE_ASSIGNMENT (( #35493 ) ) ; +#97698 = FILL_AREA_STYLE ('',( #3325 ) ) ; +#97699 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97700 = ADVANCED_FACE ( 'NONE', ( #17364 ), #89344, .T. ) ; +#97701 = ORIENTED_EDGE ( 'NONE', *, *, #75417, .F. ) ; +#97702 = FILL_AREA_STYLE ('',( #66604 ) ) ; +#97703 = CARTESIAN_POINT ( 'NONE', ( -1.899999999999999911, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#97704 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97705 = CARTESIAN_POINT ( 'NONE', ( -1.194970169649240077, -1.215709010884331143, 0.8099999999998294120 ) ) ; +#97706 = LINE ( 'NONE', #97230, #35358 ) ; +#97707 = ORIENTED_EDGE ( 'NONE', *, *, #47202, .F. ) ; +#97708 = LINE ( 'NONE', #59001, #77531 ) ; +#97709 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97710 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17338 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72357, #71881, #89204 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97711 = ORIENTED_EDGE ( 'NONE', *, *, #25606, .T. ) ; +#97713 = ORIENTED_EDGE ( 'NONE', *, *, #53753, .T. ) ; +#97712 = FILL_AREA_STYLE ('',( #19662 ) ) ; +#97714 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #30552, 'distance_accuracy_value', 'NONE'); +#97716 = PLANE ( 'NONE', #10500 ) ; +#97715 = CARTESIAN_POINT ( 'NONE', ( 3.949527124875011896, 8.130909875124988417, 0.8648700000000000276 ) ) ; +#97717 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97718 = FILL_AREA_STYLE ('',( #13423 ) ) ; +#97719 = FILL_AREA_STYLE ('',( #28338 ) ) ; +#97720 = LINE ( 'NONE', #59018, #87491 ) ; +#97721 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97722 = VERTEX_POINT ( 'NONE', #41392 ) ; +#97723 = ADVANCED_FACE ( 'NONE', ( #72504 ), #64856, .T. ) ; +#97724 = LINE ( 'NONE', #74303, #1030 ) ; +#97725 = SURFACE_STYLE_FILL_AREA ( #99192 ) ; +#97726 = CARTESIAN_POINT ( 'NONE', ( 6.544608750250088036, 2.721543249749913240, 0.8991599999999999593 ) ) ; +#97727 = STYLED_ITEM ( 'NONE', ( #50796 ), #32866 ) ; +#97728 = ORIENTED_EDGE ( 'NONE', *, *, #73964, .F. ) ; +#97730 = FILL_AREA_STYLE_COLOUR ( '', #7702 ) ; +#97729 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.03429000000000000103 ) ) ; +#97731 = ORIENTED_EDGE ( 'NONE', *, *, #55011, .T. ) ; +#97732 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97733 = AXIS2_PLACEMENT_3D ( 'NONE', #24733, #9787, #1734 ) ; +#97735 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, -1.149999999999999911 ) ) ; +#97734 = CARTESIAN_POINT ( 'NONE', ( 0.2286582822902057388, -1.314878623316919848, 0.8100000000000001643 ) ) ; +#97736 = FILL_AREA_STYLE ('',( #58029 ) ) ; +#97737 = AXIS2_PLACEMENT_3D ( 'NONE', #63890, #31722, #9169 ) ; +#97738 = CARTESIAN_POINT ( 'NONE', ( 5.928944000000000436, 13.24293800000000054, 0.8648700000000000276 ) ) ; +#97739 = VECTOR ( 'NONE', #55954, 1000.000000000000114 ) ; +#97740 = AXIS2_PLACEMENT_3D ( 'NONE', #64905, #57270, #26122 ) ; +#97741 = LINE ( 'NONE', #27879, #39245 ) ; +#97742 = ORIENTED_EDGE ( 'NONE', *, *, #91471, .F. ) ; +#97743 = SURFACE_STYLE_USAGE ( .BOTH. , #11934 ) ; +#97744 = VERTEX_POINT ( 'NONE', #91348 ) ; +#97745 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97747 = SURFACE_SIDE_STYLE ('',( #74323 ) ) ; +#97746 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999944, 0.000000000000000000, 0.1350000000000000089 ) ) ; +#97748 = CARTESIAN_POINT ( 'NONE', ( -1.244474960515300044, -1.202560495203230051, 0.8299999999999999600 ) ) ; +#97749 = LINE ( 'NONE', #35048, #26443 ) ; +#97750 = LINE ( 'NONE', #4366, #40902 ) ; +#97751 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.35000000000000142 ) ) ; +#97752 = SURFACE_STYLE_USAGE ( .BOTH. , #66649 ) ; +#97753 = SURFACE_STYLE_FILL_AREA ( #80492 ) ; +#97754 = CARTESIAN_POINT ( 'NONE', ( 1.224015772021439963, -0.9561532343638800002, 0.8299999999999999600 ) ) ; +#97755 = ORIENTED_EDGE ( 'NONE', *, *, #15870, .F. ) ; +#97756 = SURFACE_STYLE_USAGE ( .BOTH. , #84000 ) ; +#97757 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91055 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #85736, #93364, #468 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97758 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#97761 = SURFACE_STYLE_FILL_AREA ( #59055 ) ; +#97760 = CARTESIAN_POINT ( 'NONE', ( -0.9000000000000039080, -3.500000000000000444, 0.000000000000000000 ) ) ; +#97759 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 13.90000000000000036, 0.000000000000000000 ) ) ; +#97762 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #3171, 'distance_accuracy_value', 'NONE'); +#97763 = STYLED_ITEM ( 'NONE', ( #25994 ), #75697 ) ; +#97764 = VECTOR ( 'NONE', #89046, 1000.000000000000000 ) ; +#97765 = EDGE_CURVE ( 'NONE', #21034, #60355, #97471, .T. ) ; +#97766 = SURFACE_SIDE_STYLE ('',( #42208 ) ) ; +#97767 = FILL_AREA_STYLE ('',( #74838 ) ) ; +#97768 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97769 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97770 = EDGE_LOOP ( 'NONE', ( #62849, #55218, #62887, #81584 ) ) ; +#97771 = DIRECTION ( 'NONE', ( -0.7071045084557425753, 0.7071090539100477468, 0.000000000000000000 ) ) ; +#97772 = FILL_AREA_STYLE ('',( #18173 ) ) ; +#97773 = PLANE ( 'NONE', #53858 ) ; +#97774 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#97775 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2808578643762690841, 0.1400000000000000133 ) ) ; +#97776 = SURFACE_STYLE_FILL_AREA ( #51389 ) ; +#97777 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66846 ) ) ; +#97778 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97779 = FILL_AREA_STYLE_COLOUR ( '', #93493 ) ; +#97780 = EDGE_CURVE ( 'NONE', #7937, #11144, #43376, .T. ) ; +#97781 = PRESENTATION_STYLE_ASSIGNMENT (( #90683 ) ) ; +#97782 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 5.267127000000001225, 0.8991599999999999593 ) ) ; +#97783 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97784 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97785 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5 ) ) ; +#97786 = FILL_AREA_STYLE_COLOUR ( '', #20946 ) ; +#97787 = CARTESIAN_POINT ( 'NONE', ( 1.790988317735370039, -1.106837409965790053, 0.8299999999999997380 ) ) ; +#97788 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97789 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97790 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97791 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97792 = VERTEX_POINT ( 'NONE', #59248 ) ; +#97793 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97794 = CARTESIAN_POINT ( 'NONE', ( 10.91349199999999975, 11.69023699999999977, 0.8648700000000000276 ) ) ; +#97796 = LINE ( 'NONE', #83043, #9484 ) ; +#97795 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97797 = LINE ( 'NONE', #53403, #75218 ) ; +#97798 = STYLED_ITEM ( 'NONE', ( #80101 ), #93325 ) ; +#97799 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97800 = PRESENTATION_STYLE_ASSIGNMENT (( #98285 ) ) ; +#97801 = ADVANCED_FACE ( 'NONE', ( #51068 ), #90852, .F. ) ; +#97802 = ORIENTED_EDGE ( 'NONE', *, *, #94761, .T. ) ; +#97803 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97804 = VERTEX_POINT ( 'NONE', #98917 ) ; +#97805 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #74916 ), #91298 ) ; +#97806 = VECTOR ( 'NONE', #72254, 1000.000000000000000 ) ; +#97807 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#97808 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97809 = ADVANCED_FACE ( 'NONE', ( #11640 ), #67351, .T. ) ; +#97810 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97811 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63640 ), #16276 ) ; +#97812 = ORIENTED_EDGE ( 'NONE', *, *, #81155, .T. ) ; +#97813 = ORIENTED_EDGE ( 'NONE', *, *, #4656, .F. ) ; +#97814 = FILL_AREA_STYLE_COLOUR ( '', #14513 ) ; +#97815 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #40832 ), #71791 ) ; +#97816 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#97817 = ORIENTED_EDGE ( 'NONE', *, *, #68621, .T. ) ; +#97818 = CARTESIAN_POINT ( 'NONE', ( 1.818404401970810103, -1.294636995308309890, 0.8100000000000000533 ) ) ; +#97819 = SURFACE_STYLE_FILL_AREA ( #11012 ) ; +#97820 = CARTESIAN_POINT ( 'NONE', ( -1.196111491924880088, -0.8867570690059840555, 0.8299999999999997380 ) ) ; +#97821 = CARTESIAN_POINT ( 'NONE', ( 2.850000000000000089, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#97822 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#97824 = ORIENTED_EDGE ( 'NONE', *, *, #55026, .F. ) ; +#97823 = EDGE_LOOP ( 'NONE', ( #55598, #4167, #6901, #5459 ) ) ; +#97825 = AXIS2_PLACEMENT_3D ( 'NONE', #19077, #82403, #42084 ) ; +#97826 = ORIENTED_EDGE ( 'NONE', *, *, #19642, .T. ) ; +#97827 = AXIS2_PLACEMENT_3D ( 'NONE', #86717, #41284, #2468 ) ; +#97828 = VERTEX_POINT ( 'NONE', #74545 ) ; +#97829 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97830 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#97831 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #97541, 'distance_accuracy_value', 'NONE'); +#97833 = CARTESIAN_POINT ( 'NONE', ( 1.283545161422839920, -0.8955552045491329549, 0.8100000000000000533 ) ) ; +#97832 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8648700000000000276 ) ) ; +#97834 = ORIENTED_EDGE ( 'NONE', *, *, #39938, .F. ) ; +#97835 = EDGE_CURVE ( 'NONE', #76431, #10139, #12672, .T. ) ; +#97836 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97837 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97838 = CARTESIAN_POINT ( 'NONE', ( -1.361868870821330013, -0.9987792914302030534, 0.8299999999999999600 ) ) ; +#97839 = VECTOR ( 'NONE', #68173, 1000.000000000000000 ) ; +#97840 = EDGE_LOOP ( 'NONE', ( #95992, #17981, #72650, #24087 ) ) ; +#97841 = ORIENTED_EDGE ( 'NONE', *, *, #95570, .F. ) ; +#97842 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #62393, #93474, #47555, #15369 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97843 = ORIENTED_EDGE ( 'NONE', *, *, #31807, .F. ) ; +#97844 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49012 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81562, #50905, #82042 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#97845 = CARTESIAN_POINT ( 'NONE', ( 1.108771792731459982, -1.202560495203230051, 0.8100000000000000533 ) ) ; +#97847 = SURFACE_STYLE_USAGE ( .BOTH. , #74440 ) ; +#97846 = CARTESIAN_POINT ( 'NONE', ( 13.53188500000000083, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#97848 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2999999999999999334, 0.000000000000000000 ) ) ; +#97849 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97852 = ORIENTED_EDGE ( 'NONE', *, *, #44395, .F. ) ; +#97851 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #35990 ), #68517 ) ; +#97850 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97853 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#97854 = EDGE_LOOP ( 'NONE', ( #50717, #100601, #22418, #70509 ) ) ; +#97855 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#97856 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#97857 = ORIENTED_EDGE ( 'NONE', *, *, #80541, .T. ) ; +#97858 = CARTESIAN_POINT ( 'NONE', ( 5.407799999999999940, 10.95335599999999943, 0.8991599999999999593 ) ) ; +#97859 = ORIENTED_EDGE ( 'NONE', *, *, #81604, .F. ) ; +#97860 = ORIENTED_EDGE ( 'NONE', *, *, #94761, .F. ) ; +#97861 = ADVANCED_FACE ( 'NONE', ( #2404 ), #95280, .T. ) ; +#97863 = SURFACE_STYLE_FILL_AREA ( #81627 ) ; +#97862 = CARTESIAN_POINT ( 'NONE', ( 0.4785075026192849856, -0.9340610223455999561, 0.8299999999999992939 ) ) ; +#97864 = EDGE_CURVE ( 'NONE', #9642, #27821, #1901, .T. ) ; +#97865 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97866 = FILL_AREA_STYLE_COLOUR ( '', #35305 ) ; +#97867 = FILL_AREA_STYLE ('',( #66770 ) ) ; +#97868 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #64911, #25137 ), + ( #33274, #34304 ), + ( #16384, #24114 ), + ( #55262, #35807 ), + ( #27639, #5586 ), + ( #58794, #36784 ), + ( #90906, #66907 ), + ( #96524, #81268 ), + ( #89889, #59304 ), + ( #19951, #26628 ), + ( #28129, #67404 ), + ( #13214, #58295 ), + ( #19447, #51118 ), + ( #35312, #82743 ), + ( #74081, #20956 ), + ( #11190, #75578 ), + ( #5094, #12207 ), + ( #12721, #88902 ), + ( #66412, #4613 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07134662578984270198, 0.1388341252834479900, 0.2038682582026460077, 0.2661788482005160161, 0.3265850789285980049, 0.3849791193600949901, 0.4422744752917849853, 0.4992876152042279858, 0.5564569914632400138, 0.6143100800959649943, 0.6731214209110579771, 0.7340520381337829470, 0.7970235749488939758, 0.8619020797931600253, 0.9293895792867660210, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#97869 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97870 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97871 = VECTOR ( 'NONE', #44641, 1000.000000000000000 ) ; +#97872 = AXIS2_PLACEMENT_3D ( 'NONE', #93589, #24234, #94632 ) ; +#97873 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #33593, 'distance_accuracy_value', 'NONE'); +#97874 = EDGE_LOOP ( 'NONE', ( #13530, #47635, #42780, #98918 ) ) ; +#97875 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97876 = ORIENTED_EDGE ( 'NONE', *, *, #27763, .F. ) ; +#97877 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97879 = CARTESIAN_POINT ( 'NONE', ( -0.09186681814452940520, -0.9637996098261990552, 0.8100000000000000533 ) ) ; +#97878 = AXIS2_PLACEMENT_3D ( 'NONE', #38151, #76426, #21805 ) ; +#97880 = SURFACE_SIDE_STYLE ('',( #98358 ) ) ; +#97881 = VECTOR ( 'NONE', #28193, 1000.000000000000000 ) ; +#97883 = EDGE_CURVE ( 'NONE', #2533, #96454, #64188, .T. ) ; +#97882 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 1.899999999999999911, 0.1829999999999920024 ) ) ; +#97884 = VECTOR ( 'NONE', #91147, 1000.000000000000114 ) ; +#97885 = FILL_AREA_STYLE ('',( #88778 ) ) ; +#97887 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, 0.000000000000000000 ) ) ; +#97886 = AXIS2_PLACEMENT_3D ( 'NONE', #76514, #62739, #30043 ) ; +#97888 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#97889 = EDGE_LOOP ( 'NONE', ( #87232, #27040, #75906, #48642 ) ) ; +#97890 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #21339 ), #9813 ) ; +#97891 = FACE_OUTER_BOUND ( 'NONE', #2046, .T. ) ; +#97892 = FACE_OUTER_BOUND ( 'NONE', #55729, .T. ) ; +#97893 = CARTESIAN_POINT ( 'NONE', ( 0.2164741715418609935, -0.9593045227066020475, 0.8299999999999999600 ) ) ; +#97894 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97895 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 10.84999999999999964, 0.03429000000000000103 ) ) ; +#97896 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97897 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#97898 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40711, 'distance_accuracy_value', 'NONE'); +#97899 = FILL_AREA_STYLE ('',( #19847 ) ) ; +#97900 = EDGE_CURVE ( 'NONE', #82318, #51787, #58570, .T. ) ; +#97901 = STYLED_ITEM ( 'NONE', ( #37052 ), #64615 ) ; +#97902 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97903 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#97904 = STYLED_ITEM ( 'NONE', ( #22604 ), #2038 ) ; +#97905 = SURFACE_SIDE_STYLE ('',( #99368 ) ) ; +#97906 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #63731 ) ) ; +#97907 = SURFACE_SIDE_STYLE ('',( #49504 ) ) ; +#97908 = ORIENTED_EDGE ( 'NONE', *, *, #71038, .F. ) ; +#97909 = CARTESIAN_POINT ( 'NONE', ( 3.444100000000000161, 10.53504399999999919, 0.8991599999999999593 ) ) ; +#97910 = FILL_AREA_STYLE_COLOUR ( '', #73666 ) ; +#97911 = ORIENTED_EDGE ( 'NONE', *, *, #10233, .T. ) ; +#97912 = SURFACE_SIDE_STYLE ('',( #59725 ) ) ; +#97913 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #75176 ) ) ; +#97914 = EDGE_CURVE ( 'NONE', #64282, #4819, #80519, .T. ) ; +#97915 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999959943, -1.100000000000000311, -0.02000000000001884992 ) ) ; +#97916 = CARTESIAN_POINT ( 'NONE', ( 1.373198159966072529, -0.9510299480961742491, 0.8100000000000204814 ) ) ; +#97917 = LINE ( 'NONE', #60214, #12829 ) ; +#97918 = PLANE ( 'NONE', #71166 ) ; +#97919 = EDGE_CURVE ( 'NONE', #63240, #75645, #72331, .T. ) ; +#97920 = ORIENTED_EDGE ( 'NONE', *, *, #46101, .T. ) ; +#97921 = ORIENTED_EDGE ( 'NONE', *, *, #15769, .T. ) ; +#97922 = CARTESIAN_POINT ( 'NONE', ( 5.450000000000000178, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#97923 = STYLED_ITEM ( 'NONE', ( #10107 ), #45128 ) ; +#97924 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#97925 = FILL_AREA_STYLE ('',( #82187 ) ) ; +#97926 = LINE ( 'NONE', #26055, #6469 ) ; +#97927 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97928 = LINE ( 'NONE', #28542, #17558 ) ; +#97929 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97930 = SURFACE_STYLE_USAGE ( .BOTH. , #91810 ) ; +#97931 = VERTEX_POINT ( 'NONE', #18179 ) ; +#97932 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #14776 ) ) ; +#97933 = SURFACE_SIDE_STYLE ('',( #35739 ) ) ; +#97934 = VERTEX_POINT ( 'NONE', #34063 ) ; +#97935 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#97936 = CARTESIAN_POINT ( 'NONE', ( 2.350000000000000089, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#97937 = DIRECTION ( 'NONE', ( -1.084202172485500095E-15, -1.000000000000000000, -0.000000000000000000 ) ) ; +#97938 = CARTESIAN_POINT ( 'NONE', ( -0.5070681596463531005, -0.9026237492037839649, 0.8100000000000000533 ) ) ; +#97939 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, -0.000000000000000000 ) ) ; +#97941 = ORIENTED_EDGE ( 'NONE', *, *, #51905, .T. ) ; +#97940 = ORIENTED_EDGE ( 'NONE', *, *, #23671, .F. ) ; +#97942 = AXIS2_PLACEMENT_3D ( 'NONE', #73324, #18655, #80475 ) ; +#97943 = ORIENTED_EDGE ( 'NONE', *, *, #7084, .F. ) ; +#97944 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#97945 = ORIENTED_EDGE ( 'NONE', *, *, #2807, .T. ) ; +#97946 = ORIENTED_EDGE ( 'NONE', *, *, #58902, .T. ) ; +#97947 = VECTOR ( 'NONE', #49827, 1000.000000000000000 ) ; +#97948 = PRESENTATION_STYLE_ASSIGNMENT (( #20913 ) ) ; +#97949 = SURFACE_STYLE_USAGE ( .BOTH. , #50581 ) ; +#97951 = CARTESIAN_POINT ( 'NONE', ( -3.499999999999980016, 0.6999999999999999556, -0.02000000000002090036 ) ) ; +#97950 = SURFACE_STYLE_USAGE ( .BOTH. , #13685 ) ; +#97952 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97953 = VERTEX_POINT ( 'NONE', #25404 ) ; +#97954 = EDGE_LOOP ( 'NONE', ( #52996, #8507, #45893, #52197, #1530, #35441, #11260, #12935, #83903, #40634, #57110, #58108 ) ) ; +#97955 = EDGE_CURVE ( 'NONE', #89137, #36673, #88814, .T. ) ; +#97956 = ORIENTED_EDGE ( 'NONE', *, *, #6558, .T. ) ; +#97957 = EDGE_CURVE ( 'NONE', #54922, #22428, #95788, .T. ) ; +#97958 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#97959 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #26261 ), #47443 ) ; +#97960 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#97961 = ORIENTED_EDGE ( 'NONE', *, *, #80621, .T. ) ; +#97962 = FILL_AREA_STYLE_COLOUR ( '', #28593 ) ; +#97963 = SURFACE_STYLE_USAGE ( .BOTH. , #19421 ) ; +#97964 = VERTEX_POINT ( 'NONE', #96297 ) ; +#97965 = CARTESIAN_POINT ( 'NONE', ( -0.04841281441248360129, -1.230342595016630014, 0.8299999999999999600 ) ) ; +#97966 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#97967 = ORIENTED_EDGE ( 'NONE', *, *, #81936, .T. ) ; +#97968 = ORIENTED_EDGE ( 'NONE', *, *, #91739, .F. ) ; +#97969 = EDGE_CURVE ( 'NONE', #17757, #27727, #9960, .T. ) ; +#97970 = CARTESIAN_POINT ( 'NONE', ( 11.69130900000000040, 9.498205999999999705, 0.8648700000000000276 ) ) ; +#97971 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.01000000000000000021, 0.4500000000000001221 ) ) ; +#97972 = ADVANCED_FACE ( 'NONE', ( #41215 ), #21701, .T. ) ; +#97973 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#97974 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #27960 ) ) ; +#97975 = FACE_OUTER_BOUND ( 'NONE', #22190, .T. ) ; +#97976 = EDGE_CURVE ( 'NONE', #6705, #12458, #60048, .T. ) ; +#97977 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#97978 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#97979 = CARTESIAN_POINT ( 'NONE', ( -0.1000000000000017958, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#97980 = CARTESIAN_POINT ( 'NONE', ( 1.519746594691179897, -1.031932509624860161, 0.8299999999999997380 ) ) ; +#97981 = ORIENTED_EDGE ( 'NONE', *, *, #7285, .F. ) ; +#97982 = ORIENTED_EDGE ( 'NONE', *, *, #75410, .T. ) ; +#97983 = VECTOR ( 'NONE', #10887, 1000.000000000000000 ) ; +#97984 = CARTESIAN_POINT ( 'NONE', ( 5.107800000000000118, 10.45341999999999949, 0.8648700000000000276 ) ) ; +#97986 = EDGE_CURVE ( 'NONE', #14090, #65827, #98722, .T. ) ; +#97985 = LINE ( 'NONE', #74082, #61046 ) ; +#97987 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97989 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, 0.000000000000000000 ) ) ; +#97988 = LINE ( 'NONE', #3636, #57712 ) ; +#97990 = FILL_AREA_STYLE ('',( #51636 ) ) ; +#97991 = FILL_AREA_STYLE ('',( #51637 ) ) ; +#97992 = SURFACE_STYLE_USAGE ( .BOTH. , #35816 ) ; +#97993 = EDGE_CURVE ( 'NONE', #55093, #37825, #13994, .T. ) ; +#97994 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #89899 ) ) ; +#97995 = CARTESIAN_POINT ( 'NONE', ( -0.7000000000000038414, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#97996 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#97997 = ORIENTED_EDGE ( 'NONE', *, *, #6759, .F. ) ; +#97998 = EDGE_CURVE ( 'NONE', #13680, #77646, #5341, .T. ) ; +#97999 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#98000 = ADVANCED_FACE ( 'NONE', ( #14500 ), #99699, .T. ) ; +#98002 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 0.4699999999999999734, 0.000000000000000000 ) ) ; +#98001 = CARTESIAN_POINT ( 'NONE', ( -0.07325097150072405749, -1.222576472664953062, 0.8099999999999136779 ) ) ; +#98003 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #257 ) ) ; +#98004 = FILL_AREA_STYLE_COLOUR ( '', #33856 ) ; +#98005 = EDGE_CURVE ( 'NONE', #84321, #33225, #43666, .T. ) ; +#98006 = VERTEX_POINT ( 'NONE', #76318 ) ; +#98007 = LINE ( 'NONE', #94422, #28054 ) ; +#98008 = PRODUCT_RELATED_PRODUCT_CATEGORY ( 'part', '', ( #2500 ) ) ; +#98009 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98010 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#98011 = FACE_OUTER_BOUND ( 'NONE', #68325, .T. ) ; +#98012 = CARTESIAN_POINT ( 'NONE', ( 0.8333333333333293735, 3.500000000000000000, 0.000000000000000000 ) ) ; +#98013 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #28007 ), #64108 ) ; +#98014 = VECTOR ( 'NONE', #29637, 1000.000000000000000 ) ; +#98015 = CARTESIAN_POINT ( 'NONE', ( -0.3499999999999999778, -0.02000000000000000042, -0.1499999999999999944 ) ) ; +#98016 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 3.200000000000000178, 0.000000000000000000 ) ) ; +#98017 = CARTESIAN_POINT ( 'NONE', ( 12.96624500000000069, 9.676902999999999366, 0.8991599999999999593 ) ) ; +#98018 = ADVANCED_FACE ( 'NONE', ( #6318 ), #37549, .F. ) ; +#98019 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60589 ), #5127 ) ; +#98020 = VERTEX_POINT ( 'NONE', #79360 ) ; +#98021 = ORIENTED_EDGE ( 'NONE', *, *, #34730, .F. ) ; +#98022 = SURFACE_SIDE_STYLE ('',( #77118 ) ) ; +#98024 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59930, 'distance_accuracy_value', 'NONE'); +#98023 = VECTOR ( 'NONE', #3838, 1000.000000000000000 ) ; +#98025 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46954, 'distance_accuracy_value', 'NONE'); +#98026 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#98027 = CARTESIAN_POINT ( 'NONE', ( -0.2243794914328909873, -1.066507643917919967, 0.8100000000000000533 ) ) ; +#98028 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98029 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.816666666666666652, 0.000000000000000000 ) ) ; +#98030 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.123820061220075051, 0.000000000000000000 ) ) ; +#98031 = PRESENTATION_STYLE_ASSIGNMENT (( #28662 ) ) ; +#98032 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15114 ) ) ; +#98033 = ORIENTED_EDGE ( 'NONE', *, *, #49006, .T. ) ; +#98034 = EDGE_CURVE ( 'NONE', #48662, #40780, #9324, .T. ) ; +#98035 = CARTESIAN_POINT ( 'NONE', ( 10.94988400000000262, 8.003631000000000384, 0.8991599999999999593 ) ) ; +#98036 = LINE ( 'NONE', #28176, #73261 ) ; +#98037 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#98038 = ORIENTED_EDGE ( 'NONE', *, *, #58312, .F. ) ; +#98039 = SURFACE_STYLE_USAGE ( .BOTH. , #76627 ) ; +#98040 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #49222 ) ) ; +#98041 = VERTEX_POINT ( 'NONE', #23733 ) ; +#98042 = ADVANCED_FACE ( 'NONE', ( #62550 ), #53855, .T. ) ; +#98043 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #33344, #42992, #95577, #49167 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98044 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55436 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #66731, #28451, #75908 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98045 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98046 = FILL_AREA_STYLE ('',( #53670 ) ) ; +#98047 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98048 = FILL_AREA_STYLE_COLOUR ( '', #81771 ) ; +#98049 = LINE ( 'NONE', #16334, #93565 ) ; +#98050 = EDGE_CURVE ( 'NONE', #77797, #95850, #54375, .T. ) ; +#98051 = ORIENTED_EDGE ( 'NONE', *, *, #64301, .F. ) ; +#98052 = CARTESIAN_POINT ( 'NONE', ( 1.059740259740260093, -1.057183441558440018, 0.8199999999999999512 ) ) ; +#98053 = SURFACE_STYLE_FILL_AREA ( #36857 ) ; +#98054 = ORIENTED_EDGE ( 'NONE', *, *, #36282, .T. ) ; +#98055 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#98056 = ORIENTED_EDGE ( 'NONE', *, *, #90334, .F. ) ; +#98057 = ORIENTED_EDGE ( 'NONE', *, *, #84319, .F. ) ; +#98058 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8991599999999999593 ) ) ; +#98059 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #36204 ) ) ; +#98060 = VECTOR ( 'NONE', #53056, 1000.000000000000000 ) ; +#98061 = CARTESIAN_POINT ( 'NONE', ( -0.5701283774939980287, -1.188292975353419934, 0.8100000000000000533 ) ) ; +#98063 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#98062 = SURFACE_STYLE_FILL_AREA ( #92459 ) ; +#98064 = ORIENTED_EDGE ( 'NONE', *, *, #59763, .T. ) ; +#98065 = EDGE_LOOP ( 'NONE', ( #53692, #69856, #43483, #31782 ) ) ; +#98066 = EDGE_CURVE ( 'NONE', #75510, #77680, #82222, .T. ) ; +#98067 = ORIENTED_EDGE ( 'NONE', *, *, #79627, .T. ) ; +#98068 = EDGE_CURVE ( 'NONE', #100499, #74996, #19061, .T. ) ; +#98069 = AXIS2_PLACEMENT_3D ( 'NONE', #61537, #100678, #53846 ) ; +#98070 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6107 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #32678, #50537, #89311 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98071 = FILL_AREA_STYLE_COLOUR ( '', #28032 ) ; +#98072 = STYLED_ITEM ( 'NONE', ( #41652 ), #58809 ) ; +#98073 = ORIENTED_EDGE ( 'NONE', *, *, #98116, .T. ) ; +#98074 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98075 = FILL_AREA_STYLE ('',( #27735 ) ) ; +#98076 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41116 ) ) ; +#98077 = CARTESIAN_POINT ( 'NONE', ( 0.9833333333333340587, 3.099999999999980549, 0.000000000000000000 ) ) ; +#98078 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98079 = EDGE_LOOP ( 'NONE', ( #47009, #3046, #3695, #44857 ) ) ; +#98080 = SURFACE_STYLE_FILL_AREA ( #38262 ) ; +#98081 = FILL_AREA_STYLE ('',( #44027 ) ) ; +#98082 = LINE ( 'NONE', #28705, #34582 ) ; +#98083 = EDGE_LOOP ( 'NONE', ( #36213, #72391, #39453, #628, #51818, #91349, #100392, #51338 ) ) ; +#98084 = VECTOR ( 'NONE', #65916, 1000.000000000000000 ) ; +#98085 = CARTESIAN_POINT ( 'NONE', ( 0.2979301321596424801, -1.345127011520191429, 0.8100000000000000533 ) ) ; +#98086 = ADVANCED_FACE ( 'NONE', ( #33924 ), #34431, .F. ) ; +#98087 = CYLINDRICAL_SURFACE ( 'NONE', #93681, 0.009999999999999998473 ) ; +#98088 = CARTESIAN_POINT ( 'NONE', ( 0.5453366361084071023, -1.079472621882799910, 0.8299999999999999600 ) ) ; +#98089 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72150 ) ) ; +#98090 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98091 = ADVANCED_FACE ( 'NONE', ( #26260 ), #1769, .T. ) ; +#98092 = FACE_OUTER_BOUND ( 'NONE', #86971, .T. ) ; +#98093 = SURFACE_STYLE_FILL_AREA ( #98569 ) ; +#98094 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98096 = CARTESIAN_POINT ( 'NONE', ( 1.502791041020159923, -1.377680218341670093, 0.8299999999999999600 ) ) ; +#98095 = LINE ( 'NONE', #59412, #69159 ) ; +#98097 = FILL_AREA_STYLE ('',( #34410 ) ) ; +#98098 = CARTESIAN_POINT ( 'NONE', ( 2.700000000000000178, -3.149999999999959499, 0.000000000000000000 ) ) ; +#98099 = ORIENTED_EDGE ( 'NONE', *, *, #22551, .T. ) ; +#98100 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98101 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #91933 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80420, #64590, #72751 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98102 = LINE ( 'NONE', #34915, #26643 ) ; +#98103 = PRESENTATION_STYLE_ASSIGNMENT (( #83867 ) ) ; +#98104 = PLANE ( 'NONE', #53199 ) ; +#98105 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.250000000000000000, 0.000000000000000000 ) ) ; +#98106 = EDGE_CURVE ( 'NONE', #42493, #38423, #95140, .T. ) ; +#98107 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #68779 ), #93258 ) ; +#98108 = CARTESIAN_POINT ( 'NONE', ( -0.7230005133853429911, 0.6567860187191519872, 0.8100000000000000533 ) ) ; +#98109 = CARTESIAN_POINT ( 'NONE', ( 0.3000000000000000444, -0.004999999999999985359, 0.1400000000000000133 ) ) ; +#98110 = VERTEX_POINT ( 'NONE', #25751 ) ; +#98111 = VECTOR ( 'NONE', #48056, 1000.000000000000000 ) ; +#98112 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959499, -1.500000000000000000, 1.048695503451053346E-76 ) ) ; +#98113 = SURFACE_STYLE_USAGE ( .BOTH. , #78590 ) ; +#98114 = EDGE_LOOP ( 'NONE', ( #86116, #5051, #96747, #76410 ) ) ; +#98115 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98116 = EDGE_CURVE ( 'NONE', #11455, #16500, #87513, .T. ) ; +#98118 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98117 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #93268 ) ) ; +#98119 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#98120 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98121 = DIRECTION ( 'NONE', ( -1.521936902157089967E-47, 1.000000000000000000, -9.346759736391224604E-79 ) ) ; +#98122 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98123 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86995 ) ) ; +#98124 = EDGE_LOOP ( 'NONE', ( #89717, #3563, #47830, #14705, #77578, #20940, #40895, #82665, #14006, #11039, #65074, #76562 ) ) ; +#98125 = PRESENTATION_STYLE_ASSIGNMENT (( #6688 ) ) ; +#98126 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#98127 = FACE_OUTER_BOUND ( 'NONE', #15400, .T. ) ; +#98128 = LINE ( 'NONE', #43563, #98587 ) ; +#98129 = SURFACE_STYLE_USAGE ( .BOTH. , #3778 ) ; +#98130 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12521 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99226, #39047, #85493 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98131 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #83494 ), #44391 ) ; +#98132 = FILL_AREA_STYLE_COLOUR ( '', #97421 ) ; +#98133 = CARTESIAN_POINT ( 'NONE', ( 8.093173083250119859, 8.385468916749960755, 0.8991599999999999593 ) ) ; +#98134 = LINE ( 'NONE', #13887, #18086 ) ; +#98135 = CARTESIAN_POINT ( 'NONE', ( 11.67113275024997598, 5.245914249750025071, 0.8648700000000000276 ) ) ; +#98136 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#98137 = VECTOR ( 'NONE', #78272, 1000.000000000000000 ) ; +#98138 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1120, 'distance_accuracy_value', 'NONE'); +#98139 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36310 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #53394, #28411, #99268 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98140 = CARTESIAN_POINT ( 'NONE', ( 3.999024999999999608, 7.261168999999999762, 0.8991599999999999593 ) ) ; +#98141 = EDGE_CURVE ( 'NONE', #33002, #36433, #14764, .T. ) ; +#98142 = ORIENTED_EDGE ( 'NONE', *, *, #25154, .F. ) ; +#98143 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98144 = VERTEX_POINT ( 'NONE', #51749 ) ; +#98145 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98146 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #76019, 'distance_accuracy_value', 'NONE'); +#98147 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #28169, 'distance_accuracy_value', 'NONE'); +#98148 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#98149 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98150 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98151 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #93668 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76280, #10268, #18000 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98152 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, 3.500000000000000444, -3.118622929693471946E-90 ) ) ; +#98153 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98154 = CARTESIAN_POINT ( 'NONE', ( -0.2000000000000000111, 0.4245906043549200204, 0.1900000000000000022 ) ) ; +#98155 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98156 = ORIENTED_EDGE ( 'NONE', *, *, #35019, .T. ) ; +#98157 = EDGE_CURVE ( 'NONE', #55093, #61368, #35931, .T. ) ; +#98158 = VECTOR ( 'NONE', #39785, 1000.000000000000000 ) ; +#98159 = LINE ( 'NONE', #56578, #49830 ) ; +#98160 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98161 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #63136, 'distance_accuracy_value', 'NONE'); +#98162 = STYLED_ITEM ( 'NONE', ( #56335 ), #66810 ) ; +#98163 = ORIENTED_EDGE ( 'NONE', *, *, #49501, .T. ) ; +#98164 = EDGE_CURVE ( 'NONE', #79328, #63240, #907, .T. ) ; +#98165 = FILL_AREA_STYLE_COLOUR ( '', #7637 ) ; +#98166 = FACE_OUTER_BOUND ( 'NONE', #70066, .T. ) ; +#98167 = SURFACE_STYLE_FILL_AREA ( #29303 ) ; +#98168 = FACE_OUTER_BOUND ( 'NONE', #90580, .T. ) ; +#98169 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98170 = ADVANCED_FACE ( 'NONE', ( #37797 ), #22990, .T. ) ; +#98172 = ORIENTED_EDGE ( 'NONE', *, *, #44472, .T. ) ; +#98171 = VECTOR ( 'NONE', #19423, 1000.000000000000000 ) ; +#98173 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #98367, 'distance_accuracy_value', 'NONE'); +#98174 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98175 = CARTESIAN_POINT ( 'NONE', ( 7.895182750000000027, 10.29465675000000147, 0.8648700000000000276 ) ) ; +#98176 = ADVANCED_FACE ( 'NONE', ( #7055 ), #22466, .T. ) ; +#98177 = LINE ( 'NONE', #4807, #95903 ) ; +#98178 = ORIENTED_EDGE ( 'NONE', *, *, #42596, .F. ) ; +#98179 = SURFACE_SIDE_STYLE ('',( #58993 ) ) ; +#98180 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98181 = PRESENTATION_STYLE_ASSIGNMENT (( #20135 ) ) ; +#98182 = ORIENTED_EDGE ( 'NONE', *, *, #99199, .T. ) ; +#98183 = FILL_AREA_STYLE_COLOUR ( '', #97043 ) ; +#98184 = STYLED_ITEM ( 'NONE', ( #73436 ), #47045 ) ; +#98185 = EDGE_CURVE ( 'NONE', #27802, #85557, #45412, .T. ) ; +#98186 = EDGE_CURVE ( 'NONE', #90714, #54443, #51242, .T. ) ; +#98187 = VECTOR ( 'NONE', #100302, 1000.000000000000000 ) ; +#98188 = EDGE_CURVE ( 'NONE', #78125, #34361, #90530, .T. ) ; +#98189 = ORIENTED_EDGE ( 'NONE', *, *, #58722, .T. ) ; +#98190 = EDGE_CURVE ( 'NONE', #55106, #50590, #49000, .T. ) ; +#98192 = ORIENTED_EDGE ( 'NONE', *, *, #83288, .T. ) ; +#98191 = CARTESIAN_POINT ( 'NONE', ( 13.10762099999999997, 10.24254299999999951, 0.8991599999999999593 ) ) ; +#98195 = CARTESIAN_POINT ( 'NONE', ( -1.394603015216079989, -1.309512843728070086, 0.8299999999999999600 ) ) ; +#98194 = DIRECTION ( 'NONE', ( -0.3444045651374270656, 0.000000000000000000, -0.9388213331153589802 ) ) ; +#98193 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41229 ), #39602 ) ; +#98196 = PLANE ( 'NONE', #57878 ) ; +#98197 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#98198 = SURFACE_STYLE_USAGE ( .BOTH. , #43139 ) ; +#98199 = ORIENTED_EDGE ( 'NONE', *, *, #1856, .T. ) ; +#98200 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98201 = ADVANCED_FACE ( 'NONE', ( #41338 ), #2522, .T. ) ; +#98202 = STYLED_ITEM ( 'NONE', ( #67714 ), #37582 ) ; +#98203 = STYLED_ITEM ( 'NONE', ( #15911 ), #18913 ) ; +#98204 = STYLED_ITEM ( 'NONE', ( #87464 ), #34570 ) ; +#98205 = CARTESIAN_POINT ( 'NONE', ( 8.665929000000000215, 9.368346999999999980, 0.8991599999999999593 ) ) ; +#98206 = ORIENTED_EDGE ( 'NONE', *, *, #22303, .T. ) ; +#98207 = LINE ( 'NONE', #18128, #63303 ) ; +#98208 = EDGE_LOOP ( 'NONE', ( #55731, #9553, #57888, #32529 ) ) ; +#98209 = EDGE_CURVE ( 'NONE', #67111, #64979, #26158, .T. ) ; +#98210 = VECTOR ( 'NONE', #32755, 1000.000000000000000 ) ; +#98211 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #19613 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #61834, #14791, #75621 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98212 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #62448 ), #75476 ) ; +#98213 = PRESENTATION_STYLE_ASSIGNMENT (( #90117 ) ) ; +#98214 = CARTESIAN_POINT ( 'NONE', ( 3.433338500499952151, 6.695483499500052282, 0.8991599999999999593 ) ) ; +#98215 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #12919 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #76668, #61390, #6159 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98216 = VECTOR ( 'NONE', #53503, 1000.000000000000000 ) ; +#98217 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98218 = CARTESIAN_POINT ( 'NONE', ( 3.100999249749912146, 5.245913750250087659, 0.8648700000000000276 ) ) ; +#98219 = ORIENTED_EDGE ( 'NONE', *, *, #18006, .F. ) ; +#98220 = EDGE_LOOP ( 'NONE', ( #50619, #54711, #52945, #8903 ) ) ; +#98221 = LINE ( 'NONE', #19691, #29118 ) ; +#98223 = PRESENTATION_STYLE_ASSIGNMENT (( #20683 ) ) ; +#98222 = PRESENTATION_STYLE_ASSIGNMENT (( #18663 ) ) ; +#98224 = SURFACE_SIDE_STYLE ('',( #30326 ) ) ; +#98225 = FILL_AREA_STYLE_COLOUR ( '', #85661 ) ; +#98226 = VECTOR ( 'NONE', #55574, 1000.000000000000114 ) ; +#98227 = SURFACE_STYLE_FILL_AREA ( #67151 ) ; +#98228 = SURFACE_STYLE_FILL_AREA ( #99688 ) ; +#98229 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98230 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98231 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98232 = ORIENTED_EDGE ( 'NONE', *, *, #72502, .T. ) ; +#98233 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98234 = EDGE_CURVE ( 'NONE', #10422, #55589, #56673, .T. ) ; +#98235 = VECTOR ( 'NONE', #15755, 1000.000000000000000 ) ; +#98238 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98237 = PLANE ( 'NONE', #84885 ) ; +#98236 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, -0.000000000000000000 ) ) ; +#98239 = CARTESIAN_POINT ( 'NONE', ( 12.34600000000000186, 7.592200000000000060, 0.8991599999999999593 ) ) ; +#98240 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.499999999999989786, 0.1829999999999999960 ) ) ; +#98241 = SURFACE_STYLE_FILL_AREA ( #26889 ) ; +#98242 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98243 = EDGE_CURVE ( 'NONE', #89541, #15311, #94899, .T. ) ; +#98244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98245 = CARTESIAN_POINT ( 'NONE', ( 1.400822000000000234, 10.32344800000000085, 0.8991599999999999593 ) ) ; +#98246 = ORIENTED_EDGE ( 'NONE', *, *, #65555, .T. ) ; +#98247 = LINE ( 'NONE', #58059, #83179 ) ; +#98248 = SURFACE_STYLE_USAGE ( .BOTH. , #59580 ) ; +#98249 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999334, 0.2784314575050762519, 0.1458578643762690197 ) ) ; +#98250 = STYLED_ITEM ( 'NONE', ( #36923 ), #87790 ) ; +#98251 = CIRCLE ( 'NONE', #85048, 0.01000000000000002623 ) ; +#98252 = FACE_OUTER_BOUND ( 'NONE', #30710, .T. ) ; +#98253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98254 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220045297, -1.300000000000000044, -0.02000000000000000042 ) ) ; +#98255 = CARTESIAN_POINT ( 'NONE', ( 10.84999999999999964, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#98256 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31494 ), #62494 ) ; +#98257 = PRESENTATION_STYLE_ASSIGNMENT (( #96799 ) ) ; +#98258 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98259 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98260 = PRESENTATION_STYLE_ASSIGNMENT (( #65692 ) ) ; +#98261 = LINE ( 'NONE', #22235, #97352 ) ; +#98262 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98263 = EDGE_CURVE ( 'NONE', #4035, #28482, #26018, .T. ) ; +#98264 = STYLED_ITEM ( 'NONE', ( #21187 ), #75901 ) ; +#98265 = CARTESIAN_POINT ( 'NONE', ( -1.458578643762689975, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#98266 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98267 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87210, 'distance_accuracy_value', 'NONE'); +#98268 = CARTESIAN_POINT ( 'NONE', ( 6.325406000000000084, 6.617701000000000278, 0.8991599999999999593 ) ) ; +#98269 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #29889 ), #16818 ) ; +#98270 = CARTESIAN_POINT ( 'NONE', ( -0.2582749839912160117, -0.9663557550577259736, 0.8300000000000009592 ) ) ; +#98271 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#98272 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #39605 ) ) ; +#98273 = CARTESIAN_POINT ( 'NONE', ( -0.9202467668417529945, -1.279077976066830047, 0.8100000000000000533 ) ) ; +#98274 = EDGE_LOOP ( 'NONE', ( #89254, #63602, #39211, #18733 ) ) ; +#98275 = EDGE_CURVE ( 'NONE', #56505, #212, #93868, .T. ) ; +#98276 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98277 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93154, 'distance_accuracy_value', 'NONE'); +#98279 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #59263 ) ) ; +#98278 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2750000000000000222, -0.1400000000000000133 ) ) ; +#98280 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #86, 'distance_accuracy_value', 'NONE'); +#98281 = SURFACE_STYLE_USAGE ( .BOTH. , #4410 ) ; +#98282 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98283 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #5800 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79610, #2499, #79104 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98284 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87279 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22769, #36225, #51567 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98285 = SURFACE_STYLE_USAGE ( .BOTH. , #82062 ) ; +#98286 = ORIENTED_EDGE ( 'NONE', *, *, #100897, .T. ) ; +#98287 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, -3.500000000000000000, 0.8299999999999999600 ) ) ; +#98288 = PRESENTATION_STYLE_ASSIGNMENT (( #67211 ) ) ; +#98289 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #65727 ) ) ; +#98290 = EDGE_CURVE ( 'NONE', #8523, #36275, #16787, .T. ) ; +#98291 = VERTEX_POINT ( 'NONE', #71457 ) ; +#98292 = VECTOR ( 'NONE', #76330, 1000.000000000000000 ) ; +#98293 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #71160, 'distance_accuracy_value', 'NONE'); +#98294 = VECTOR ( 'NONE', #94237, 1000.000000000000000 ) ; +#98295 = PLANE ( 'NONE', #42534 ) ; +#98296 = EDGE_CURVE ( 'NONE', #56847, #5565, #44678, .T. ) ; +#98297 = LINE ( 'NONE', #59621, #33934 ) ; +#98298 = VERTEX_POINT ( 'NONE', #55164 ) ; +#98299 = ORIENTED_EDGE ( 'NONE', *, *, #37745, .T. ) ; +#98300 = AXIS2_PLACEMENT_3D ( 'NONE', #32951, #11386, #18085 ) ; +#98301 = ORIENTED_EDGE ( 'NONE', *, *, #90188, .F. ) ; +#98302 = CARTESIAN_POINT ( 'NONE', ( 1.803030467297160211, -1.264112177694660000, 0.8299999999999999600 ) ) ; +#98303 = CARTESIAN_POINT ( 'NONE', ( 8.800000000000000711, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#98304 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98305 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 1.500000000000000000, 0.000000000000000000 ) ) ; +#98306 = FACE_OUTER_BOUND ( 'NONE', #20144, .T. ) ; +#98307 = ADVANCED_FACE ( 'NONE', ( #85747 ), #47969, .T. ) ; +#98308 = PLANE ( 'NONE', #36267 ) ; +#98310 = ORIENTED_EDGE ( 'NONE', *, *, #2696, .T. ) ; +#98309 = ORIENTED_EDGE ( 'NONE', *, *, #10869, .T. ) ; +#98311 = AXIS2_PLACEMENT_3D ( 'NONE', #21080, #76190, #99079 ) ; +#98312 = VERTEX_POINT ( 'NONE', #27528 ) ; +#98313 = ADVANCED_FACE ( 'NONE', ( #20334 ), #10572, .T. ) ; +#98314 = VERTEX_POINT ( 'NONE', #43823 ) ; +#98315 = EDGE_CURVE ( 'NONE', #64979, #17126, #59197, .T. ) ; +#98316 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98317 = FILL_AREA_STYLE_COLOUR ( '', #84871 ) ; +#98318 = FILL_AREA_STYLE ('',( #68229 ) ) ; +#98319 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999959943, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#98320 = EDGE_CURVE ( 'NONE', #93560, #99206, #72970, .T. ) ; +#98321 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98322 = VERTEX_POINT ( 'NONE', #50017 ) ; +#98323 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98324 = ORIENTED_EDGE ( 'NONE', *, *, #92081, .F. ) ; +#98325 = VECTOR ( 'NONE', #73895, 1000.000000000000000 ) ; +#98326 = VERTEX_POINT ( 'NONE', #98372 ) ; +#98327 = CARTESIAN_POINT ( 'NONE', ( 1.028534346447049996, -1.164020980542209927, 0.8299999999999999600 ) ) ; +#98328 = EDGE_CURVE ( 'NONE', #28098, #27976, #51531, .T. ) ; +#98330 = FACE_OUTER_BOUND ( 'NONE', #9624, .T. ) ; +#98329 = FACE_OUTER_BOUND ( 'NONE', #13671, .T. ) ; +#98331 = SURFACE_STYLE_FILL_AREA ( #19804 ) ; +#98332 = ORIENTED_EDGE ( 'NONE', *, *, #22343, .F. ) ; +#98333 = LINE ( 'NONE', #12574, #10645 ) ; +#98334 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -3.614007241618339896E-16 ) ) ; +#98335 = STYLED_ITEM ( 'NONE', ( #22243 ), #36302 ) ; +#98336 = ORIENTED_EDGE ( 'NONE', *, *, #78119, .T. ) ; +#98338 = SURFACE_SIDE_STYLE ('',( #84100 ) ) ; +#98337 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -0.02000000000000000042, 0.2500000000000000000 ) ) ; +#98339 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98340 = VERTEX_POINT ( 'NONE', #35198 ) ; +#98341 = ORIENTED_EDGE ( 'NONE', *, *, #87382, .T. ) ; +#98343 = FILL_AREA_STYLE ('',( #50984 ) ) ; +#98342 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98344 = LINE ( 'NONE', #21313, #83153 ) ; +#98345 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#98346 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98347 = CIRCLE ( 'NONE', #69012, 0.009999999999999998473 ) ; +#98348 = SURFACE_SIDE_STYLE ('',( #59171 ) ) ; +#98349 = PRESENTATION_STYLE_ASSIGNMENT (( #83119 ) ) ; +#98350 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41382 ), #529 ) ; +#98351 = DIRECTION ( 'NONE', ( -8.980489425909800160E-49, 5.551115123125790098E-17, 1.000000000000000000 ) ) ; +#98352 = VECTOR ( 'NONE', #52859, 1000.000000000000000 ) ; +#98353 = LINE ( 'NONE', #90776, #182 ) ; +#98354 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98355 = EDGE_LOOP ( 'NONE', ( #100297, #2314, #7488, #7755 ) ) ; +#98356 = ORIENTED_EDGE ( 'NONE', *, *, #29336, .F. ) ; +#98357 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8100000000000000533 ) ) ; +#98358 = SURFACE_STYLE_FILL_AREA ( #35682 ) ; +#98359 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8991599999999999593 ) ) ; +#98360 = SURFACE_STYLE_USAGE ( .BOTH. , #14129 ) ; +#98361 = EDGE_CURVE ( 'NONE', #8949, #83336, #72416, .T. ) ; +#98362 = SURFACE_STYLE_FILL_AREA ( #33151 ) ; +#98363 = FILL_AREA_STYLE ('',( #28996 ) ) ; +#98364 = VERTEX_POINT ( 'NONE', #58187 ) ; +#98365 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98366 = FACE_OUTER_BOUND ( 'NONE', #87313, .T. ) ; +#98367 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98368 = LINE ( 'NONE', #28506, #47774 ) ; +#98369 = LINE ( 'NONE', #59700, #31339 ) ; +#98370 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #70669 ) ) ; +#98371 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.433333333333333570, 0.000000000000000000 ) ) ; +#98372 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.7000000000000006217, -0.02000000000000000042 ) ) ; +#98373 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #64429 ), #626 ) ; +#98374 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98375 = PLANE ( 'NONE', #79231 ) ; +#98376 = PLANE ( 'NONE', #48941 ) ; +#98377 = SURFACE_SIDE_STYLE ('',( #68301 ) ) ; +#98378 = FILL_AREA_STYLE ('',( #36695 ) ) ; +#98379 = CARTESIAN_POINT ( 'NONE', ( -0.2327516233766240561, 0.7099999999999999645, -1.839345217873099381E-17 ) ) ; +#98380 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#98381 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #39847, 'distance_accuracy_value', 'NONE'); +#98382 = ORIENTED_EDGE ( 'NONE', *, *, #42670, .F. ) ; +#98383 = SURFACE_STYLE_USAGE ( .BOTH. , #90813 ) ; +#98384 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155850987, 0.8100000000000292522 ) ) ; +#98385 = ORIENTED_EDGE ( 'NONE', *, *, #67858, .T. ) ; +#98386 = FACE_OUTER_BOUND ( 'NONE', #56355, .T. ) ; +#98387 = ADVANCED_FACE ( 'NONE', ( #49494 ), #18823, .T. ) ; +#98388 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98390 = CARTESIAN_POINT ( 'NONE', ( 11.79841300000000004, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#98389 = VECTOR ( 'NONE', #37430, 1000.000000000000000 ) ; +#98391 = CARTESIAN_POINT ( 'NONE', ( 0.6999999999999999556, 0.01000000000000000021, 0.000000000000000000 ) ) ; +#98392 = CARTESIAN_POINT ( 'NONE', ( 1.363558791120762281, -0.9410130125528619605, 0.8100000000000269207 ) ) ; +#98394 = STYLED_ITEM ( 'NONE', ( #99615 ), #47612 ) ; +#98393 = CARTESIAN_POINT ( 'NONE', ( 1.441265085512748012, -1.324294193063880742, 0.8099999999997858913 ) ) ; +#98395 = LINE ( 'NONE', #83674, #41810 ) ; +#98396 = ORIENTED_EDGE ( 'NONE', *, *, #88341, .T. ) ; +#98397 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 2.700000000000000178, 0.8299999999999999600 ) ) ; +#98398 = CARTESIAN_POINT ( 'NONE', ( 9.020149180195748090E-35, 15.40000000000000036, 0.8648700000000000276 ) ) ; +#98399 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #8391, 'distance_accuracy_value', 'NONE'); +#98400 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98401 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72312 ), #77260 ) ; +#98402 = SURFACE_STYLE_FILL_AREA ( #75024 ) ; +#98403 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #70731, 'distance_accuracy_value', 'NONE'); +#98404 = EDGE_CURVE ( 'NONE', #56862, #66668, #15143, .T. ) ; +#98405 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.01085786437626904202, 0.1400000000000000133 ) ) ; +#98406 = ORIENTED_EDGE ( 'NONE', *, *, #48458, .F. ) ; +#98407 = VERTEX_POINT ( 'NONE', #46296 ) ; +#98408 = AXIS2_PLACEMENT_3D ( 'NONE', #62368, #92940, #39353 ) ; +#98409 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #62103, 'distance_accuracy_value', 'NONE'); +#98410 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, 0.2999999999999989897, -0.02000000000000000042 ) ) ; +#98411 = ORIENTED_EDGE ( 'NONE', *, *, #8316, .T. ) ; +#98412 = PRESENTATION_STYLE_ASSIGNMENT (( #89828 ) ) ; +#98413 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #23418 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #20180, #59044, #35552 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98414 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#98415 = SURFACE_STYLE_FILL_AREA ( #5533 ) ; +#98416 = LINE ( 'NONE', #24449, #56157 ) ; +#98417 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98418 = CARTESIAN_POINT ( 'NONE', ( -0.4385307926823460711, -0.9262267064097939873, 0.8100000000000000533 ) ) ; +#98419 = CARTESIAN_POINT ( 'NONE', ( -1.220268398896690032, -0.9623790331012080923, 0.8100000000000000533 ) ) ; +#98420 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98422 = EDGE_LOOP ( 'NONE', ( #3274, #66244, #79834, #58893, #32929, #25554, #78640, #25265 ) ) ; +#98421 = VERTEX_POINT ( 'NONE', #29987 ) ; +#98423 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #98924 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #82212, #41895, #74552 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98424 = ORIENTED_EDGE ( 'NONE', *, *, #40810, .F. ) ; +#98425 = EDGE_CURVE ( 'NONE', #33464, #24193, #13103, .T. ) ; +#98426 = PRESENTATION_STYLE_ASSIGNMENT (( #14192 ) ) ; +#98427 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#98428 = VECTOR ( 'NONE', #44863, 1000.000000000000000 ) ; +#98429 = ORIENTED_EDGE ( 'NONE', *, *, #11063, .F. ) ; +#98430 = EDGE_LOOP ( 'NONE', ( #99875, #44271 ) ) ; +#98431 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #1390, #47335, #41210, #34061 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98432 = CYLINDRICAL_SURFACE ( 'NONE', #7166, 0.009999999999999998473 ) ; +#98433 = CARTESIAN_POINT ( 'NONE', ( -0.2899999999999999800, -0.01499999999999995261, -0.1458578643762691029 ) ) ; +#98434 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #41471 ) ) ; +#98436 = SURFACE_STYLE_FILL_AREA ( #52086 ) ; +#98435 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#98437 = EDGE_LOOP ( 'NONE', ( #81089, #42909, #1207, #52355 ) ) ; +#98438 = ORIENTED_EDGE ( 'NONE', *, *, #10591, .F. ) ; +#98439 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #20310, #42316, #74961, #96394 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98440 = VERTEX_POINT ( 'NONE', #76464 ) ; +#98441 = FILL_AREA_STYLE_COLOUR ( '', #77301 ) ; +#98442 = FILL_AREA_STYLE_COLOUR ( '', #18357 ) ; +#98443 = ADVANCED_FACE ( 'NONE', ( #6940 ), #77463, .F. ) ; +#98444 = FILL_AREA_STYLE_COLOUR ( '', #93368 ) ; +#98445 = STYLED_ITEM ( 'NONE', ( #94262 ), #71465 ) ; +#98447 = ORIENTED_EDGE ( 'NONE', *, *, #63332, .F. ) ; +#98446 = PLANE ( 'NONE', #62529 ) ; +#98448 = CARTESIAN_POINT ( 'NONE', ( 12.39841599999999922, 10.20531300000000030, 0.8991599999999999593 ) ) ; +#98449 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #6874 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #70030, #54760, #9188 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98450 = EDGE_LOOP ( 'NONE', ( #42657, #12579, #67102, #92116 ) ) ; +#98451 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98452 = CARTESIAN_POINT ( 'NONE', ( 10.49026500000000084, 4.984284999999999854, 0.8648700000000000276 ) ) ; +#98453 = ORIENTED_EDGE ( 'NONE', *, *, #24737, .T. ) ; +#98454 = ORIENTED_EDGE ( 'NONE', *, *, #91014, .T. ) ; +#98455 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 9.934200000000000585, 0.8991599999999999593 ) ) ; +#98456 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#98457 = SURFACE_STYLE_FILL_AREA ( #53101 ) ; +#98458 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46321 ), #34943 ) ; +#98459 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98460 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98461 = VECTOR ( 'NONE', #99003, 1000.000000000000000 ) ; +#98462 = SURFACE_STYLE_USAGE ( .BOTH. , #27123 ) ; +#98463 = CARTESIAN_POINT ( 'NONE', ( 0.7000000000000009548, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#98464 = SURFACE_SIDE_STYLE ('',( #12198 ) ) ; +#98465 = EDGE_CURVE ( 'NONE', #26599, #61349, #92758, .T. ) ; +#98466 = CARTESIAN_POINT ( 'NONE', ( 1.560249861737120103, -0.9531265814360270205, 0.8299999999999997380 ) ) ; +#98467 = ORIENTED_EDGE ( 'NONE', *, *, #22388, .F. ) ; +#98468 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98469 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80939 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89224, #83072, #65748 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98470 = CARTESIAN_POINT ( 'NONE', ( -0.9164863243573180274, -1.381526214478759895, 0.8100000000000000533 ) ) ; +#98471 = EDGE_LOOP ( 'NONE', ( #47178, #81078, #5750, #1484 ) ) ; +#98472 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #72769, #65595, #19641, #50815 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98473 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98474 = VECTOR ( 'NONE', #78096, 1000.000000000000000 ) ; +#98475 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98476 = PRESENTATION_STYLE_ASSIGNMENT (( #19452 ) ) ; +#98478 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98477 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460026, -1.445454545454550210, 0.8099999999998321876 ) ) ; +#98480 = AXIS2_PLACEMENT_3D ( 'NONE', #13762, #37337, #67437 ) ; +#98479 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98481 = EDGE_CURVE ( 'NONE', #83076, #20765, #28508, .T. ) ; +#98483 = AXIS2_PLACEMENT_3D ( 'NONE', #75565, #75084, #22435 ) ; +#98482 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #39898 ), #65996 ) ; +#98484 = AXIS2_PLACEMENT_3D ( 'NONE', #87160, #55541, #23367 ) ; +#98485 = SURFACE_STYLE_FILL_AREA ( #5599 ) ; +#98486 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98487 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98488 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98490 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98489 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98491 = SURFACE_STYLE_USAGE ( .BOTH. , #57293 ) ; +#98492 = VECTOR ( 'NONE', #77575, 1000.000000000000000 ) ; +#98493 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #67159, 'distance_accuracy_value', 'NONE'); +#98494 = VERTEX_POINT ( 'NONE', #29510 ) ; +#98495 = EDGE_CURVE ( 'NONE', #15315, #15997, #21962, .T. ) ; +#98496 = LINE ( 'NONE', #28639, #83881 ) ; +#98497 = SURFACE_STYLE_USAGE ( .BOTH. , #18581 ) ; +#98498 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98499 = SURFACE_SIDE_STYLE ('',( #27670 ) ) ; +#98500 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#98501 = LINE ( 'NONE', #67920, #96093 ) ; +#98502 = VECTOR ( 'NONE', #9292, 1000.000000000000114 ) ; +#98503 = LINE ( 'NONE', #98016, #67563 ) ; +#98504 = SURFACE_SIDE_STYLE ('',( #99498 ) ) ; +#98505 = ORIENTED_EDGE ( 'NONE', *, *, #57891, .T. ) ; +#98506 = ORIENTED_EDGE ( 'NONE', *, *, #5957, .T. ) ; +#98507 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25991, 'distance_accuracy_value', 'NONE'); +#98508 = FILL_AREA_STYLE_COLOUR ( '', #88000 ) ; +#98509 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.500000000000000444, 8.977651093538432215E-153 ) ) ; +#98510 = CARTESIAN_POINT ( 'NONE', ( -0.1401145506032289989, -0.9647878283071119609, 0.8100000000000000533 ) ) ; +#98511 = SURFACE_SIDE_STYLE ('',( #53157 ) ) ; +#98512 = SURFACE_STYLE_FILL_AREA ( #76619 ) ; +#98513 = AXIS2_PLACEMENT_3D ( 'NONE', #4780, #44099, #89570 ) ; +#98514 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#98515 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98516 = FILL_AREA_STYLE ('',( #74134 ) ) ; +#98517 = ORIENTED_EDGE ( 'NONE', *, *, #24302, .T. ) ; +#98518 = ADVANCED_FACE ( 'NONE', ( #67787 ), #98858, .T. ) ; +#98519 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98520 = FILL_AREA_STYLE_COLOUR ( '', #3127 ) ; +#98521 = EDGE_CURVE ( 'NONE', #51457, #43255, #39171, .T. ) ; +#98522 = ORIENTED_EDGE ( 'NONE', *, *, #68957, .T. ) ; +#98523 = FILL_AREA_STYLE ('',( #12263 ) ) ; +#98524 = AXIS2_PLACEMENT_3D ( 'NONE', #63879, #39356, #85315 ) ; +#98525 = AXIS2_PLACEMENT_3D ( 'NONE', #51388, #65175, #83015 ) ; +#98526 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#98527 = ORIENTED_EDGE ( 'NONE', *, *, #21012, .F. ) ; +#98528 = LINE ( 'NONE', #82319, #45161 ) ; +#98529 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#98530 = CARTESIAN_POINT ( 'NONE', ( 0.0001801288999998471030, 3.199999293324040650E-09, 0.000000000000000000 ) ) ; +#98531 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98532 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7349 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13805, #59880, #28203 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98533 = DIRECTION ( 'NONE', ( -1.000000000000000000, -8.052359004764721492E-109, -6.165170508236590408E-78 ) ) ; +#98534 = EDGE_LOOP ( 'NONE', ( #77384, #60130, #93195, #75250 ) ) ; +#98535 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -0.3000000000000019873, 0.1829999999999709637 ) ) ; +#98536 = ORIENTED_EDGE ( 'NONE', *, *, #16789, .F. ) ; +#98537 = ADVANCED_FACE ( 'NONE', ( #86651 ), #64187, .F. ) ; +#98538 = STYLED_ITEM ( 'NONE', ( #6704 ), #20448 ) ; +#98539 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #66287, #50493, #44276, #19300, #36162, #51981, #43789, #51492, #97862, #97384, #81626, #75437, #11563, #67269, #83114, #59166, #4479, #90766, #34658 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.894494522339967325E-05, 3.738232288171398931E-05, 5.558643286595918811E-05, 7.340334889677175905E-05, 9.095838293808791556E-05, 0.0001079455471239354150, 0.0001246850330689952449, 0.0001412992953462922127, 0.0001577964274159769111, 0.0001744505950076815379, 0.0001913214496316886727, 0.0002087459928697857174, 0.0002268007666079478951, 0.0002454329050348251495, 0.0002649334608642065175, 0.0002855918020719671897 ), + .UNSPECIFIED. ) ; +#98541 = CARTESIAN_POINT ( 'NONE', ( -0.4841855288935910107, -0.9911177488655089629, 0.8100000000000000533 ) ) ; +#98540 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 1.050000000000000044, 0.000000000000000000 ) ) ; +#98542 = ORIENTED_EDGE ( 'NONE', *, *, #52182, .F. ) ; +#98543 = ORIENTED_EDGE ( 'NONE', *, *, #67242, .F. ) ; +#98546 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #53863 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51986, #60168, #37164 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98545 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57943 ) ) ; +#98544 = FILL_AREA_STYLE_COLOUR ( '', #74217 ) ; +#98547 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98548 = FILL_AREA_STYLE ('',( #3210 ) ) ; +#98549 = ORIENTED_EDGE ( 'NONE', *, *, #46355, .T. ) ; +#98550 = EDGE_LOOP ( 'NONE', ( #62712, #90063, #17487, #9908, #27895, #98286 ) ) ; +#98551 = ORIENTED_EDGE ( 'NONE', *, *, #71549, .T. ) ; +#98552 = EDGE_CURVE ( 'NONE', #88447, #74547, #46817, .T. ) ; +#98553 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98555 = EDGE_LOOP ( 'NONE', ( #97376, #37225, #37754, #19532, #896, #76810 ) ) ; +#98554 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98556 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94702 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #13396, #92074, #69057 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98557 = FILL_AREA_STYLE_COLOUR ( '', #60644 ) ; +#98558 = SURFACE_STYLE_FILL_AREA ( #98075 ) ; +#98559 = CARTESIAN_POINT ( 'NONE', ( 9.231614999999999682, 8.802661000000002289, 0.8648700000000000276 ) ) ; +#98560 = ORIENTED_EDGE ( 'NONE', *, *, #43752, .T. ) ; +#98561 = LINE ( 'NONE', #97124, #26097 ) ; +#98562 = FILL_AREA_STYLE ('',( #82844 ) ) ; +#98563 = VERTEX_POINT ( 'NONE', #1393 ) ; +#98564 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44891, 'distance_accuracy_value', 'NONE'); +#98565 = FACE_OUTER_BOUND ( 'NONE', #24987, .T. ) ; +#98566 = CARTESIAN_POINT ( 'NONE', ( 0.5426878470553200273, -1.110278784363659899, 0.8299999999999999600 ) ) ; +#98567 = VECTOR ( 'NONE', #56255, 1000.000000000000000 ) ; +#98568 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98569 = FILL_AREA_STYLE ('',( #77942 ) ) ; +#98571 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98570 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#98572 = CARTESIAN_POINT ( 'NONE', ( -0.9269136212724455870, -1.264135989007900918, 0.8099999999997935518 ) ) ; +#98573 = EDGE_CURVE ( 'NONE', #45093, #26971, #31013, .T. ) ; +#98574 = VECTOR ( 'NONE', #85337, 999.9999999999998863 ) ; +#98575 = CARTESIAN_POINT ( 'NONE', ( 0.009999999999999998473, 0.2500000000000000000, 0.6499230723708768753 ) ) ; +#98576 = ORIENTED_EDGE ( 'NONE', *, *, #85371, .T. ) ; +#98577 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98578 = CARTESIAN_POINT ( 'NONE', ( 6.650674750249975453, 1.696237750249974141, 0.8648700000000000276 ) ) ; +#98579 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18778 ), #41701 ) ; +#98580 = CARTESIAN_POINT ( 'NONE', ( 1.106746768919629975, -1.124851061273939967, 0.8300000000000022915 ) ) ; +#98582 = CARTESIAN_POINT ( 'NONE', ( 1.363042397695183094, -1.357204004350421656, 0.8099999999997652411 ) ) ; +#98581 = CARTESIAN_POINT ( 'NONE', ( 4.900000000000000355, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#98583 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.750000000000000000, 0.03429000000000000103 ) ) ; +#98584 = SURFACE_STYLE_FILL_AREA ( #12330 ) ; +#98585 = EDGE_CURVE ( 'NONE', #100686, #9642, #86132, .T. ) ; +#98586 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85633 ), #75868 ) ; +#98587 = VECTOR ( 'NONE', #57419, 1000.000000000000000 ) ; +#98588 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 3.520000000000000018, 0.000000000000000000 ) ) ; +#98589 = EDGE_CURVE ( 'NONE', #67222, #97114, #17188, .T. ) ; +#98590 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #85640 ), #93754 ) ; +#98591 = ORIENTED_EDGE ( 'NONE', *, *, #11063, .T. ) ; +#98592 = STYLED_ITEM ( 'NONE', ( #35609 ), #48538 ) ; +#98593 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98594 = FACE_OUTER_BOUND ( 'NONE', #41293, .T. ) ; +#98595 = CARTESIAN_POINT ( 'NONE', ( -0.7175470460908950354, 1.464404984293220080, 0.8299999999999999600 ) ) ; +#98596 = VERTEX_POINT ( 'NONE', #40208 ) ; +#98598 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 14.25000000000000000, 0.000000000000000000 ) ) ; +#98597 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98599 = EDGE_CURVE ( 'NONE', #85273, #86742, #41213, .T. ) ; +#98601 = SURFACE_SIDE_STYLE ('',( #7181 ) ) ; +#98600 = SURFACE_STYLE_USAGE ( .BOTH. , #67525 ) ; +#98602 = DIRECTION ( 'NONE', ( 1.836970198721029688E-16, -0.000000000000000000, 1.000000000000000000 ) ) ; +#98603 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98604 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98605 = STYLED_ITEM ( 'NONE', ( #19980 ), #20688 ) ; +#98606 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98607 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98608 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56333 ) ) ; +#98609 = ORIENTED_EDGE ( 'NONE', *, *, #77444, .T. ) ; +#98610 = SURFACE_SIDE_STYLE ('',( #5730 ) ) ; +#98611 = LINE ( 'NONE', #53741, #59349 ) ; +#98612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98615 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #819 ), #26943 ) ; +#98614 = AXIS2_PLACEMENT_3D ( 'NONE', #75073, #45869, #29586 ) ; +#98613 = CARTESIAN_POINT ( 'NONE', ( 2.590800000000000214, 9.934200000000000585, 0.8648700000000000276 ) ) ; +#98616 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#98617 = PRESENTATION_STYLE_ASSIGNMENT (( #6213 ) ) ; +#98618 = SURFACE_SIDE_STYLE ('',( #53258 ) ) ; +#98619 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -1.300000000000000266, 0.1829999999999580573 ) ) ; +#98620 = CARTESIAN_POINT ( 'NONE', ( -1.600000000000000089, 0.4600000000000000200, 1.100000000000000089 ) ) ; +#98621 = CARTESIAN_POINT ( 'NONE', ( -2.299999999999999822, 3.520000000000000018, 0.1829999999999999960 ) ) ; +#98622 = LINE ( 'NONE', #82903, #26870 ) ; +#98623 = ADVANCED_FACE ( 'NONE', ( #62686 ), #23884, .T. ) ; +#98624 = EDGE_CURVE ( 'NONE', #16296, #26704, #64681, .T. ) ; +#98625 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98626 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98627 = SURFACE_STYLE_FILL_AREA ( #74745 ) ; +#98628 = VERTEX_POINT ( 'NONE', #42704 ) ; +#98629 = ORIENTED_EDGE ( 'NONE', *, *, #25533, .T. ) ; +#98630 = VECTOR ( 'NONE', #48187, 1000.000000000000000 ) ; +#98631 = CYLINDRICAL_SURFACE ( 'NONE', #22549, 0.04999999999999969746 ) ; +#98632 = PRESENTATION_STYLE_ASSIGNMENT (( #75736 ) ) ; +#98633 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999949929, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#98634 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98635 = FACE_OUTER_BOUND ( 'NONE', #54873, .T. ) ; +#98636 = VECTOR ( 'NONE', #69311, 1000.000000000000000 ) ; +#98637 = SURFACE_SIDE_STYLE ('',( #5252 ) ) ; +#98638 = CARTESIAN_POINT ( 'NONE', ( 1.847806625102409894, -0.9622763341455700115, 0.8100000000000000533 ) ) ; +#98639 = PRESENTATION_STYLE_ASSIGNMENT (( #92058 ) ) ; +#98640 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98641 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#98642 = ORIENTED_EDGE ( 'NONE', *, *, #53336, .T. ) ; +#98643 = EDGE_CURVE ( 'NONE', #7028, #70633, #57828, .T. ) ; +#98644 = FILL_AREA_STYLE ('',( #45558 ) ) ; +#98645 = FILL_AREA_STYLE_COLOUR ( '', #100638 ) ; +#98646 = ADVANCED_FACE ( 'NONE', ( #50409 ), #81549, .T. ) ; +#98647 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #96051 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99044, #89967, #44007 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98648 = FILL_AREA_STYLE ('',( #90067 ) ) ; +#98649 = ORIENTED_EDGE ( 'NONE', *, *, #27015, .T. ) ; +#98650 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98651 = PRESENTATION_STYLE_ASSIGNMENT (( #67576 ) ) ; +#98652 = CARTESIAN_POINT ( 'NONE', ( 6.427863999999999578, 11.59270000000000067, 0.8648700000000000276 ) ) ; +#98653 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#98654 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98655 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98656 = ORIENTED_EDGE ( 'NONE', *, *, #28271, .F. ) ; +#98657 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#98658 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98659 = EDGE_CURVE ( 'NONE', #82928, #71500, #6342, .T. ) ; +#98660 = PRESENTATION_STYLE_ASSIGNMENT (( #61982 ) ) ; +#98661 = VECTOR ( 'NONE', #39255, 1000.000000000000000 ) ; +#98662 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98663 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98664 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98665 = ORIENTED_EDGE ( 'NONE', *, *, #45567, .T. ) ; +#98666 = EDGE_CURVE ( 'NONE', #37342, #1018, #30179, .T. ) ; +#98667 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #13645 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #58132, #72392, #10512 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98668 = SURFACE_STYLE_FILL_AREA ( #5790 ) ; +#98669 = CARTESIAN_POINT ( 'NONE', ( 0.1999999999999999833, -0.02000000000000000042, -0.1499999999999999667 ) ) ; +#98670 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8236 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #60153, #90243, #37150 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98671 = CARTESIAN_POINT ( 'NONE', ( 1.549081571661369949, -1.457888621141530061, 0.8300000000000001821 ) ) ; +#98672 = ORIENTED_EDGE ( 'NONE', *, *, #13058, .F. ) ; +#98673 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #42815, #51510 ), + ( #12594, #83632 ), + ( #29497, #21833 ), + ( #97879, #59181 ), + ( #52488, #36677 ), + ( #60182, #44291 ), + ( #75955, #68769 ), + ( #43807, #84120 ), + ( #28493, #13594 ), + ( #74966, #60657 ), + ( #91273, #83126 ), + ( #29971, #28018 ), + ( #13087, #14124 ), + ( #67772, #99819 ), + ( #43305, #98844 ), + ( #44783, #82141 ), + ( #37176, #61168 ), + ( #12086, #68278 ), + ( #98357, #52998 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.06711270624433779419, 0.1316627967036539948, 0.1946925457082870070, 0.2551393896941889783, 0.3150988967389449780, 0.3737760910910559731, 0.4326889284963120197, 0.4916570744764829914, 0.5505745229127320117, 0.6091822301749569846, 0.6680950675802129757, 0.7284339546221080264, 0.7906699720419050337, 0.8564705032580119948, 0.9262308729472129576, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98674 = ADVANCED_FACE ( 'NONE', ( #98252 ), #84503, .T. ) ; +#98675 = EDGE_CURVE ( 'NONE', #30679, #75172, #44681, .T. ) ; +#98676 = ORIENTED_EDGE ( 'NONE', *, *, #35822, .F. ) ; +#98678 = ORIENTED_EDGE ( 'NONE', *, *, #7094, .F. ) ; +#98677 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98679 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91995, 'distance_accuracy_value', 'NONE'); +#98680 = LINE ( 'NONE', #21162, #58919 ) ; +#98682 = CARTESIAN_POINT ( 'NONE', ( -1.321337043985290061, -1.462480703074420019, 0.8299999999999999600 ) ) ; +#98681 = SURFACE_STYLE_USAGE ( .BOTH. , #51326 ) ; +#98683 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2700000000000000178, -0.1250000000000000000 ) ) ; +#98685 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #97142 ) ) ; +#98684 = CARTESIAN_POINT ( 'NONE', ( 5.130394999999999150, 8.392538999999999305, 0.8648700000000000276 ) ) ; +#98686 = ORIENTED_EDGE ( 'NONE', *, *, #64586, .F. ) ; +#98687 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 12.55000000000000071, 0.03429000000000000103 ) ) ; +#98688 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -13.54999999999999893 ) ) ; +#98689 = ORIENTED_EDGE ( 'NONE', *, *, #70097, .F. ) ; +#98690 = CARTESIAN_POINT ( 'NONE', ( 1.440857328897279910, -1.359907766992060285, 0.8299999999999999600 ) ) ; +#98691 = AXIS2_PLACEMENT_3D ( 'NONE', #99793, #20294, #84094 ) ; +#98692 = FACE_OUTER_BOUND ( 'NONE', #34814, .T. ) ; +#98693 = AXIS2_PLACEMENT_3D ( 'NONE', #91923, #44928, #35837 ) ; +#98694 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98695 = VERTEX_POINT ( 'NONE', #28881 ) ; +#98697 = SURFACE_STYLE_FILL_AREA ( #100173 ) ; +#98696 = CARTESIAN_POINT ( 'NONE', ( 1.785976973916959754, -1.116141175150469733, 0.8099999999999998312 ) ) ; +#98698 = ORIENTED_EDGE ( 'NONE', *, *, #22563, .T. ) ; +#98699 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98700 = VECTOR ( 'NONE', #56745, 1000.000000000000000 ) ; +#98701 = FILL_AREA_STYLE_COLOUR ( '', #14047 ) ; +#98702 = EDGE_CURVE ( 'NONE', #59157, #91073, #37568, .T. ) ; +#98703 = PLANE ( 'NONE', #97 ) ; +#98704 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #1896 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89257, #90238, #11043 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98705 = STYLED_ITEM ( 'NONE', ( #16596 ), #13005 ) ; +#98706 = ORIENTED_EDGE ( 'NONE', *, *, #28385, .T. ) ; +#98707 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98708 = ORIENTED_EDGE ( 'NONE', *, *, #90875, .T. ) ; +#98709 = LINE ( 'NONE', #67143, #58529 ) ; +#98710 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98711 = EDGE_CURVE ( 'NONE', #21399, #72982, #37069, .T. ) ; +#98712 = SURFACE_STYLE_USAGE ( .BOTH. , #82986 ) ; +#98713 = PRESENTATION_STYLE_ASSIGNMENT (( #43166 ) ) ; +#98716 = EDGE_CURVE ( 'NONE', #1586, #90881, #68167, .T. ) ; +#98715 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98714 = ADVANCED_BREP_SHAPE_REPRESENTATION ( '', ( #88305, #82894 ), #7788 ) ; +#98717 = AXIS2_PLACEMENT_3D ( 'NONE', #33529, #79993, #91015 ) ; +#98718 = CARTESIAN_POINT ( 'NONE', ( 9.920019999999999172, 2.283599999999999852, 0.8648700000000000276 ) ) ; +#98719 = FILL_AREA_STYLE_COLOUR ( '', #82133 ) ; +#98720 = FILL_AREA_STYLE_COLOUR ( '', #12808 ) ; +#98721 = ORIENTED_EDGE ( 'NONE', *, *, #67069, .T. ) ; +#98722 = LINE ( 'NONE', #75326, #79132 ) ; +#98724 = STYLED_ITEM ( 'NONE', ( #4483 ), #29989 ) ; +#98723 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 3.200000000000000178, 0.000000000000000000 ) ) ; +#98725 = ADVANCED_FACE ( 'NONE', ( #99246 ), #51885, .T. ) ; +#98728 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.300000000000000266, -0.02000000000000000042 ) ) ; +#98727 = FACE_OUTER_BOUND ( 'NONE', #35528, .T. ) ; +#98726 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 6.599999999999999645, 0.03429000000000000103 ) ) ; +#98729 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #4911, 'distance_accuracy_value', 'NONE'); +#98730 = CARTESIAN_POINT ( 'NONE', ( 13.05000000000000071, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#98731 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #72736 ), #35231 ) ; +#98732 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #100235 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #23020, #62842, #54677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98733 = STYLED_ITEM ( 'NONE', ( #38312 ), #54568 ) ; +#98734 = FACE_OUTER_BOUND ( 'NONE', #92091, .T. ) ; +#98735 = SURFACE_SIDE_STYLE ('',( #91163 ) ) ; +#98736 = ORIENTED_EDGE ( 'NONE', *, *, #58241, .T. ) ; +#98737 = AXIS2_PLACEMENT_3D ( 'NONE', #10778, #19013, #74171 ) ; +#98738 = FACE_OUTER_BOUND ( 'NONE', #96231, .T. ) ; +#98739 = VECTOR ( 'NONE', #14372, 1000.000000000000000 ) ; +#98740 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#98741 = FILL_AREA_STYLE_COLOUR ( '', #39202 ) ; +#98742 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87386 ) ) ; +#98743 = FILL_AREA_STYLE_COLOUR ( '', #13712 ) ; +#98744 = SURFACE_SIDE_STYLE ('',( #96791 ) ) ; +#98745 = DIRECTION ( 'NONE', ( 0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#98746 = LINE ( 'NONE', #85004, #17039 ) ; +#98747 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#98748 = AXIS2_PLACEMENT_3D ( 'NONE', #85092, #45747, #37645 ) ; +#98749 = AXIS2_PLACEMENT_3D ( 'NONE', #26067, #65864, #80193 ) ; +#98750 = SURFACE_SIDE_STYLE ('',( #58571 ) ) ; +#98751 = FILL_AREA_STYLE ('',( #38065 ) ) ; +#98752 = EDGE_CURVE ( 'NONE', #4524, #75920, #32918, .T. ) ; +#98753 = EDGE_CURVE ( 'NONE', #7813, #94260, #16547, .T. ) ; +#98754 = SURFACE_STYLE_FILL_AREA ( #37578 ) ; +#98756 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98755 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98757 = PRESENTATION_STYLE_ASSIGNMENT (( #89681 ) ) ; +#98758 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.149999999999999911, -0.02000000000000000042 ) ) ; +#98759 = CARTESIAN_POINT ( 'NONE', ( 11.47917699999999996, 11.83165800000000090, 0.8991599999999999593 ) ) ; +#98760 = SURFACE_STYLE_USAGE ( .BOTH. , #20220 ) ; +#98761 = LINE ( 'NONE', #7335, #89734 ) ; +#98762 = LINE ( 'NONE', #75362, #66701 ) ; +#98763 = DIRECTION ( 'NONE', ( -0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#98764 = CARTESIAN_POINT ( 'NONE', ( 1.816666666666666652, 3.099999999999969891, 0.000000000000000000 ) ) ; +#98765 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, 3.383333333333330195, 0.000000000000000000 ) ) ; +#98766 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98767 = CARTESIAN_POINT ( 'NONE', ( -0.9276048691944630553, -1.263266231710209908, 0.8100000000000000533 ) ) ; +#98768 = VERTEX_POINT ( 'NONE', #32418 ) ; +#98769 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98770 = VECTOR ( 'NONE', #70778, 1000.000000000000000 ) ; +#98771 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #78445, #8409, #78949, #71808 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#98772 = EDGE_CURVE ( 'NONE', #9771, #45850, #40074, .T. ) ; +#98773 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59773 ), #63024 ) ; +#98774 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98775 = SURFACE_STYLE_FILL_AREA ( #27939 ) ; +#98776 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63954 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65123, #24469, #92815 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98777 = FACE_OUTER_BOUND ( 'NONE', #51945, .T. ) ; +#98778 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98779 = EDGE_LOOP ( 'NONE', ( #72802, #37005, #19311, #6383 ) ) ; +#98780 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98781 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98782 = VECTOR ( 'NONE', #57011, 1000.000000000000000 ) ; +#98783 = ORIENTED_EDGE ( 'NONE', *, *, #29114, .T. ) ; +#98784 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98785 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98786 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #23337, #57427 ) ; +#98787 = CARTESIAN_POINT ( 'NONE', ( 7.994763999999999982, 11.80755800000000022, 0.8991599999999999593 ) ) ; +#98788 = VERTEX_POINT ( 'NONE', #95158 ) ; +#98789 = ORIENTED_EDGE ( 'NONE', *, *, #40233, .T. ) ; +#98790 = FACE_OUTER_BOUND ( 'NONE', #19400, .T. ) ; +#98791 = ORIENTED_EDGE ( 'NONE', *, *, #45039, .T. ) ; +#98792 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98793 = VECTOR ( 'NONE', #99468, 1000.000000000000000 ) ; +#98794 = FACE_OUTER_BOUND ( 'NONE', #49556, .T. ) ; +#98795 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, 1.399999999999999911, -13.54999999999999893 ) ) ; +#98796 = PRESENTATION_STYLE_ASSIGNMENT (( #35625 ) ) ; +#98797 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#98799 = ORIENTED_EDGE ( 'NONE', *, *, #87097, .T. ) ; +#98798 = EDGE_LOOP ( 'NONE', ( #37548, #44876, #70104, #17436 ) ) ; +#98800 = ADVANCED_FACE ( 'NONE', ( #23251 ), #39065, .T. ) ; +#98801 = ORIENTED_EDGE ( 'NONE', *, *, #80915, .F. ) ; +#98802 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98803 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46284, 'distance_accuracy_value', 'NONE'); +#98804 = FILL_AREA_STYLE_COLOUR ( '', #94641 ) ; +#98806 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#98805 = SURFACE_STYLE_USAGE ( .BOTH. , #4449 ) ; +#98807 = EDGE_CURVE ( 'NONE', #19442, #46152, #70694, .T. ) ; +#98808 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98809 = CARTESIAN_POINT ( 'NONE', ( -1.353802252918679949, -0.9813977598329840513, 0.8299999999999999600 ) ) ; +#98810 = ORIENTED_EDGE ( 'NONE', *, *, #48355, .F. ) ; +#98811 = STYLED_ITEM ( 'NONE', ( #58412 ), #78987 ) ; +#98812 = SURFACE_SIDE_STYLE ('',( #52451 ) ) ; +#98813 = ORIENTED_EDGE ( 'NONE', *, *, #85284, .T. ) ; +#98814 = ORIENTED_EDGE ( 'NONE', *, *, #56419, .T. ) ; +#98815 = CARTESIAN_POINT ( 'NONE', ( 1.041560975556909963, -1.173235213159260049, 0.8299999999999999600 ) ) ; +#98816 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #44340 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #9999, #41267, #40756 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98817 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#98818 = ADVANCED_FACE ( 'NONE', ( #7823 ), #71718, .T. ) ; +#98819 = VECTOR ( 'NONE', #61175, 1000.000000000000000 ) ; +#98821 = VERTEX_POINT ( 'NONE', #65547 ) ; +#98820 = SURFACE_STYLE_USAGE ( .BOTH. , #6423 ) ; +#98822 = CARTESIAN_POINT ( 'NONE', ( -3.123820061220025313, -2.499999999999999556, 0.000000000000000000 ) ) ; +#98823 = VECTOR ( 'NONE', #91294, 1000.000000000000000 ) ; +#98824 = CARTESIAN_POINT ( 'NONE', ( 9.153833000000000553, 5.203488000000001001, 0.8648700000000000276 ) ) ; +#98825 = ORIENTED_EDGE ( 'NONE', *, *, #63910, .T. ) ; +#98826 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.2600000000000000089, 0.1250000000000000000 ) ) ; +#98827 = ORIENTED_EDGE ( 'NONE', *, *, #53982, .F. ) ; +#98828 = EDGE_LOOP ( 'NONE', ( #42601, #65482, #78559, #91870, #52427, #13427 ) ) ; +#98829 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#98830 = EDGE_CURVE ( 'NONE', #43512, #72032, #3780, .T. ) ; +#98831 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8991599999999999593 ) ) ; +#98832 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #40991 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #69250, #22855, #53988 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98833 = FILL_AREA_STYLE_COLOUR ( '', #92130 ) ; +#98834 = VECTOR ( 'NONE', #33454, 1000.000000000000000 ) ; +#98835 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98836 = CARTESIAN_POINT ( 'NONE', ( -1.500000000000000000, -3.520000000000000018, 0.1829999999999999960 ) ) ; +#98837 = AXIS2_PLACEMENT_3D ( 'NONE', #14044, #45203, #6373 ) ; +#98838 = SURFACE_STYLE_FILL_AREA ( #38163 ) ; +#98839 = ORIENTED_EDGE ( 'NONE', *, *, #40491, .F. ) ; +#98840 = CARTESIAN_POINT ( 'NONE', ( -1.449999999999999956, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#98841 = ORIENTED_EDGE ( 'NONE', *, *, #78146, .T. ) ; +#98842 = ADVANCED_FACE ( 'NONE', ( #50285 ), #57425, .F. ) ; +#98843 = FILL_AREA_STYLE_COLOUR ( '', #17903 ) ; +#98844 = CARTESIAN_POINT ( 'NONE', ( -0.01185217942543770157, -1.028719707420159946, 0.8299999999999999600 ) ) ; +#98845 = CARTESIAN_POINT ( 'NONE', ( 1.119708175802679895, -1.130592060098940088, 0.8100000000000000533 ) ) ; +#98847 = AXIS2_PLACEMENT_3D ( 'NONE', #85829, #55723, #54717 ) ; +#98846 = SURFACE_SIDE_STYLE ('',( #29499 ) ) ; +#98848 = LINE ( 'NONE', #13599, #55230 ) ; +#98849 = FILL_AREA_STYLE_COLOUR ( '', #7574 ) ; +#98850 = ADVANCED_FACE ( 'NONE', ( #34945 ), #18577, .T. ) ; +#98851 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#98852 = VERTEX_POINT ( 'NONE', #27280 ) ; +#98853 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#98854 = CARTESIAN_POINT ( 'NONE', ( 0.1711848682203470362, -1.102962211187280106, 0.8100000000000000533 ) ) ; +#98855 = CARTESIAN_POINT ( 'NONE', ( 13.70000000000000107, 0.000000000000000000, -13.54999999999999893 ) ) ; +#98856 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34204 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #40241, #87696, #56595 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98857 = SURFACE_STYLE_FILL_AREA ( #52010 ) ; +#98858 = PLANE ( 'NONE', #98484 ) ; +#98859 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #56577 ) ) ; +#98860 = CARTESIAN_POINT ( 'NONE', ( 1.894788238603390296, -1.280379325981960026, 0.8299999999999999600 ) ) ; +#98861 = EDGE_CURVE ( 'NONE', #63380, #74215, #11843, .T. ) ; +#98863 = EDGE_CURVE ( 'NONE', #48771, #63839, #10851, .T. ) ; +#98862 = CARTESIAN_POINT ( 'NONE', ( 12.75196900000000255, 10.55886599999999831, 0.8991599999999999593 ) ) ; +#98864 = FILL_AREA_STYLE ('',( #28511 ) ) ; +#98865 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41911 ), #97324 ) ; +#98866 = SURFACE_STYLE_FILL_AREA ( #98378 ) ; +#98867 = SURFACE_STYLE_USAGE ( .BOTH. , #85135 ) ; +#98868 = CARTESIAN_POINT ( 'NONE', ( 0.4958578643762691085, -0.01085786437626907325, 0.2500000000000000000 ) ) ; +#98869 = SURFACE_STYLE_USAGE ( .BOTH. , #67794 ) ; +#98870 = EDGE_CURVE ( 'NONE', #78529, #89943, #26779, .T. ) ; +#98871 = EDGE_CURVE ( 'NONE', #52069, #30664, #17562, .T. ) ; +#98872 = FILL_AREA_STYLE ('',( #29995 ) ) ; +#98873 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63127 ), #22281 ) ; +#98874 = STYLED_ITEM ( 'NONE', ( #36189 ), #90751 ) ; +#98875 = ORIENTED_EDGE ( 'NONE', *, *, #24276, .F. ) ; +#98876 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#98877 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999989875, 1.350000000000000089, 0.000000000000000000 ) ) ; +#98878 = CARTESIAN_POINT ( 'NONE', ( 3.200000000000000178, 14.25000000000000000, 0.000000000000000000 ) ) ; +#98879 = ORIENTED_EDGE ( 'NONE', *, *, #55634, .F. ) ; +#98880 = LINE ( 'NONE', #45314, #82101 ) ; +#98882 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79456 ), #81073 ) ; +#98881 = SURFACE_STYLE_FILL_AREA ( #67801 ) ; +#98883 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999980549, 0.5500000000000000444, -0.02000000000000000042 ) ) ; +#98884 = ADVANCED_FACE ( 'NONE', ( #9843 ), #42589, .T. ) ; +#98885 = CARTESIAN_POINT ( 'NONE', ( 11.95397600000000082, 5.528756999999999699, 0.8991599999999999593 ) ) ; +#98887 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#98886 = VECTOR ( 'NONE', #22063, 1000.000000000000000 ) ; +#98888 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#98889 = CARTESIAN_POINT ( 'NONE', ( 1.418522800700448006, -1.250624474938031527, 0.8099999999998324096 ) ) ; +#98890 = EDGE_CURVE ( 'NONE', #84241, #60734, #45533, .T. ) ; +#98891 = VECTOR ( 'NONE', #14065, 1000.000000000000000 ) ; +#98892 = PLANE ( 'NONE', #97233 ) ; +#98893 = VERTEX_POINT ( 'NONE', #68548 ) ; +#98894 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#98895 = SURFACE_SIDE_STYLE ('',( #30015 ) ) ; +#98896 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.300000000000000266, 1.048695503451051965E-76 ) ) ; +#98897 = DIRECTION ( 'NONE', ( 0.7071067789140474957, 0.7071067834590476497, 0.000000000000000000 ) ) ; +#98898 = SURFACE_SIDE_STYLE ('',( #13644 ) ) ; +#98899 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77007 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #3187, #25675, #2698 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98900 = LINE ( 'NONE', #52535, #35549 ) ; +#98901 = FILL_AREA_STYLE_COLOUR ( '', #41320 ) ; +#98902 = CLOSED_SHELL ( 'NONE', ( #67522, #45885, #49616, #35594, #20174, #99431 ) ) ; +#98903 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #15807 ) ) ; +#98904 = EDGE_LOOP ( 'NONE', ( #65787, #17828, #29550, #57467 ) ) ; +#98905 = VERTEX_POINT ( 'NONE', #98133 ) ; +#98906 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#98907 = ORIENTED_EDGE ( 'NONE', *, *, #82837, .F. ) ; +#98908 = CARTESIAN_POINT ( 'NONE', ( -0.1199320083468070064, -1.507611749840819915, 0.8299999999999999600 ) ) ; +#98909 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34062 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #75633, #67943, #84788 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98910 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 11.70000000000000107, 0.03429000000000000103 ) ) ; +#98911 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#98912 = STYLED_ITEM ( 'NONE', ( #10668 ), #14625 ) ; +#98913 = SURFACE_SIDE_STYLE ('',( #29067 ) ) ; +#98914 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98915 = PRESENTATION_STYLE_ASSIGNMENT (( #74543 ) ) ; +#98916 = CARTESIAN_POINT ( 'NONE', ( -1.220268398896690032, -0.9623790331012080923, 0.8299999999999999600 ) ) ; +#98917 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.099999999999969891, 0.000000000000000000 ) ) ; +#98919 = ORIENTED_EDGE ( 'NONE', *, *, #15664, .T. ) ; +#98918 = ORIENTED_EDGE ( 'NONE', *, *, #78715, .F. ) ; +#98920 = EDGE_CURVE ( 'NONE', #93347, #81611, #82899, .T. ) ; +#98921 = ORIENTED_EDGE ( 'NONE', *, *, #90001, .F. ) ; +#98922 = CARTESIAN_POINT ( 'NONE', ( 1.512782233897559836, -1.071137013546419992, 0.8099999999999981659 ) ) ; +#98923 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #41203, 'distance_accuracy_value', 'NONE'); +#98924 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82212, 'distance_accuracy_value', 'NONE'); +#98926 = LINE ( 'NONE', #76525, #77276 ) ; +#98925 = FILL_AREA_STYLE ('',( #84200 ) ) ; +#98927 = ORIENTED_EDGE ( 'NONE', *, *, #96250, .F. ) ; +#98928 = EDGE_CURVE ( 'NONE', #11057, #89393, #46723, .T. ) ; +#98929 = VERTEX_POINT ( 'NONE', #76725 ) ; +#98930 = LINE ( 'NONE', #13682, #98428 ) ; +#98931 = SURFACE_SIDE_STYLE ('',( #54071 ) ) ; +#98932 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #67795 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #74395, #19767, #43239 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98933 = CARTESIAN_POINT ( 'NONE', ( -0.4143618085515369809, -0.9701298701298699534, 0.8099999999998293010 ) ) ; +#98935 = ORIENTED_EDGE ( 'NONE', *, *, #13073, .F. ) ; +#98934 = VECTOR ( 'NONE', #2391, 1000.000000000000000 ) ; +#98936 = CARTESIAN_POINT ( 'NONE', ( -0.5999999999999989786, -9.750000000000000000, 0.6500000000000001332 ) ) ; +#98937 = ORIENTED_EDGE ( 'NONE', *, *, #15192, .T. ) ; +#98938 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#98939 = VERTEX_POINT ( 'NONE', #98619 ) ; +#98940 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43556 ) ) ; +#98941 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #72955 ) ) ; +#98942 = FACE_OUTER_BOUND ( 'NONE', #41778, .T. ) ; +#98943 = ORIENTED_EDGE ( 'NONE', *, *, #39715, .F. ) ; +#98944 = CARTESIAN_POINT ( 'NONE', ( 9.917225000000000179, 12.51509500000000052, 0.8991599999999999593 ) ) ; +#98945 = SURFACE_STYLE_FILL_AREA ( #67868 ) ; +#98946 = ORIENTED_EDGE ( 'NONE', *, *, #76896, .T. ) ; +#98947 = ORIENTED_EDGE ( 'NONE', *, *, #56018, .F. ) ; +#98948 = VECTOR ( 'NONE', #83406, 1000.000000000000000 ) ; +#98949 = EDGE_CURVE ( 'NONE', #88638, #9393, #29751, .T. ) ; +#98950 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#98951 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98952 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#98953 = ORIENTED_EDGE ( 'NONE', *, *, #69827, .F. ) ; +#98954 = VECTOR ( 'NONE', #81905, 999.9999999999998863 ) ; +#98955 = FILL_AREA_STYLE ('',( #44896 ) ) ; +#98956 = VERTEX_POINT ( 'NONE', #21599 ) ; +#98957 = FILL_AREA_STYLE_COLOUR ( '', #8872 ) ; +#98958 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #51157 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14907, #76226, #61944 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98959 = VECTOR ( 'NONE', #60237, 1000.000000000000000 ) ; +#98960 = LINE ( 'NONE', #21447, #96931 ) ; +#98961 = AXIS2_PLACEMENT_3D ( 'NONE', #93792, #63238, #918 ) ; +#98962 = SHAPE_REPRESENTATION ( 'Submodel-D__3D_design_ESP32-S3_module_module_ESP32-S3-MINI-1U-3D_PCB_ESP32-S3-MINI-1U_V1.1_20210824_PCB_3D_ImportedPartModels_C0201_20210301.STEP', ( #4347, #37013 ), #69549 ) ; +#98963 = FACE_OUTER_BOUND ( 'NONE', #73313, .T. ) ; +#98964 = SURFACE_STYLE_USAGE ( .BOTH. , #36788 ) ; +#98965 = SURFACE_STYLE_FILL_AREA ( #67890 ) ; +#98966 = CLOSED_SHELL ( 'NONE', ( #40948, #62086, #38614, #33403, #10108, #979 ) ) ; +#98967 = CARTESIAN_POINT ( 'NONE', ( 0.2314326298701299411, 0.7099999999999999645, -5.421010862427522170E-17 ) ) ; +#98968 = VECTOR ( 'NONE', #21465, 1000.000000000000000 ) ; +#98969 = VECTOR ( 'NONE', #4372, 1000.000000000000000 ) ; +#98970 = CARTESIAN_POINT ( 'NONE', ( 6.428880000000000372, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#98971 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#98972 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#98973 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#98974 = SURFACE_SIDE_STYLE ('',( #60308 ) ) ; +#98975 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #87423 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #21809, #90250, #20810 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98976 = FILL_AREA_STYLE_COLOUR ( '', #32549 ) ; +#98977 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #83905 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #17403, #18408, #78209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#98979 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 1.699999999999999956, -0.02000000000000839995 ) ) ; +#98978 = SURFACE_STYLE_USAGE ( .BOTH. , #44915 ) ; +#98980 = SURFACE_STYLE_USAGE ( .BOTH. , #35827 ) ; +#98981 = STYLED_ITEM ( 'NONE', ( #14656 ), #43718 ) ; +#98982 = EDGE_CURVE ( 'NONE', #71358, #26858, #44080, .T. ) ; +#98983 = ORIENTED_EDGE ( 'NONE', *, *, #10642, .F. ) ; +#98984 = CARTESIAN_POINT ( 'NONE', ( -1.002767861914739989, -1.390055052842650074, 0.8299999999999999600 ) ) ; +#98985 = FILL_AREA_STYLE ('',( #15678 ) ) ; +#98986 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #18295, 'distance_accuracy_value', 'NONE'); +#98987 = LINE ( 'NONE', #67915, #85699 ) ; +#98988 = CARTESIAN_POINT ( 'NONE', ( 6.650000000000000355, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#98989 = CARTESIAN_POINT ( 'NONE', ( 0.4217626140292745629, -1.177853988920071204, 0.8100000000000000533 ) ) ; +#98990 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#98992 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#98991 = STYLED_ITEM ( 'NONE', ( #88335 ), #73337 ) ; +#98993 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#98994 = LINE ( 'NONE', #14274, #52124 ) ; +#98995 = PRESENTATION_STYLE_ASSIGNMENT (( #67921 ) ) ; +#98996 = EDGE_CURVE ( 'NONE', #88364, #17633, #12264, .T. ) ; +#98997 = AXIS2_PLACEMENT_3D ( 'NONE', #6805, #15524, #78366 ) ; +#98998 = VERTEX_POINT ( 'NONE', #37933 ) ; +#98999 = ORIENTED_EDGE ( 'NONE', *, *, #54012, .T. ) ; +#99000 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99001 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #16419, 'distance_accuracy_value', 'NONE'); +#99002 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #58482, 'distance_accuracy_value', 'NONE'); +#99003 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#99004 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, 4.049999999999999822, 0.03429000000000000103 ) ) ; +#99005 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14545 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #99244, #7820, #91171 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99006 = SURFACE_STYLE_USAGE ( .BOTH. , #85278 ) ; +#99007 = PRESENTATION_STYLE_ASSIGNMENT (( #14288 ) ) ; +#99008 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999949907, -1.850000000000000311, 0.000000000000000000 ) ) ; +#99009 = CARTESIAN_POINT ( 'NONE', ( 4.049999999999999822, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#99010 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -3.149999999999990585, 0.000000000000000000 ) ) ; +#99011 = CARTESIAN_POINT ( 'NONE', ( 12.04606400000000122, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#99012 = ORIENTED_EDGE ( 'NONE', *, *, #100663, .T. ) ; +#99014 = DIRECTION ( 'NONE', ( -0.7071067819560475920, 0.7071067804170475535, 0.000000000000000000 ) ) ; +#99013 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #7689 ) ) ; +#99015 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99016 = EDGE_LOOP ( 'NONE', ( #91932, #66729, #17856, #46468 ) ) ; +#99017 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, -9.880000000000000782, 0.4000000000000000222 ) ) ; +#99018 = AXIS2_PLACEMENT_3D ( 'NONE', #96644, #48724, #17528 ) ; +#99019 = ORIENTED_EDGE ( 'NONE', *, *, #65746, .T. ) ; +#99020 = FILL_AREA_STYLE ('',( #82320 ) ) ; +#99021 = VECTOR ( 'NONE', #44635, 1000.000000000000000 ) ; +#99022 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.979898987322330051, 0.000000000000000000 ) ) ; +#99023 = ADVANCED_FACE ( 'NONE', ( #67058 ), #53259, .T. ) ; +#99024 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99025 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#99026 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #3878 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #39945, #71090, #32292 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99027 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999940137, -2.500000000000000000, -0.02000000000000000042 ) ) ; +#99029 = ORIENTED_EDGE ( 'NONE', *, *, #79053, .T. ) ; +#99028 = ORIENTED_EDGE ( 'NONE', *, *, #41981, .T. ) ; +#99030 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99032 = VECTOR ( 'NONE', #29640, 1000.000000000000000 ) ; +#99031 = CARTESIAN_POINT ( 'NONE', ( -2.100000000000000089, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#99033 = VERTEX_POINT ( 'NONE', #92035 ) ; +#99034 = VECTOR ( 'NONE', #83693, 1000.000000000000000 ) ; +#99035 = SURFACE_SIDE_STYLE ('',( #60368 ) ) ; +#99036 = AXIS2_PLACEMENT_3D ( 'NONE', #100255, #54949, #31438 ) ; +#99038 = LINE ( 'NONE', #6141, #61279 ) ; +#99037 = SURFACE_SIDE_STYLE ('',( #76151 ) ) ; +#99039 = CLOSED_SHELL ( 'NONE', ( #25196, #8961, #15516, #68967, #68412, #96243 ) ) ; +#99040 = ORIENTED_EDGE ( 'NONE', *, *, #89069, .T. ) ; +#99041 = EDGE_CURVE ( 'NONE', #50477, #41527, #99119, .T. ) ; +#99042 = ORIENTED_EDGE ( 'NONE', *, *, #49023, .T. ) ; +#99043 = PLANE ( 'NONE', #54631 ) ; +#99044 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99045 = FILL_AREA_STYLE ('',( #20519 ) ) ; +#99046 = SURFACE_STYLE_FILL_AREA ( #52204 ) ; +#99048 = SURFACE_STYLE_FILL_AREA ( #37383 ) ; +#99047 = FILL_AREA_STYLE_COLOUR ( '', #33402 ) ; +#99050 = VERTEX_POINT ( 'NONE', #35951 ) ; +#99049 = CIRCLE ( 'NONE', #74736, 0.1100000000000007222 ) ; +#99051 = ORIENTED_EDGE ( 'NONE', *, *, #64734, .F. ) ; +#99052 = ORIENTED_EDGE ( 'NONE', *, *, #90190, .F. ) ; +#99053 = AXIS2_PLACEMENT_3D ( 'NONE', #73494, #34203, #19343 ) ; +#99054 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000020295, 0.1458578643762672711 ) ) ; +#99055 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #66564 ) ) ; +#99056 =( REPRESENTATION_RELATIONSHIP ('NONE','NONE', #37058, #65081 ) REPRESENTATION_RELATIONSHIP_WITH_TRANSFORMATION ( #88106 )SHAPE_REPRESENTATION_RELATIONSHIP( ) ); +#99059 = ORIENTED_EDGE ( 'NONE', *, *, #11732, .F. ) ; +#99058 = STYLED_ITEM ( 'NONE', ( #69038 ), #43772 ) ; +#99057 = SURFACE_STYLE_FILL_AREA ( #59394 ) ; +#99060 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99061 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, 3.500000000000000444, 0.000000000000000000 ) ) ; +#99062 = PRESENTATION_STYLE_ASSIGNMENT (( #91983 ) ) ; +#99063 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99064 = ORIENTED_EDGE ( 'NONE', *, *, #85865, .F. ) ; +#99065 = FILL_AREA_STYLE ('',( #37401 ) ) ; +#99066 = LINE ( 'NONE', #51215, #96541 ) ; +#99067 = ORIENTED_EDGE ( 'NONE', *, *, #54844, .F. ) ; +#99068 = ADVANCED_FACE ( 'NONE', ( #14394 ), #82410, .T. ) ; +#99069 = SURFACE_STYLE_USAGE ( .BOTH. , #29711 ) ; +#99070 = PRODUCT_DEFINITION_FORMATION_WITH_SPECIFIED_SOURCE ( 'ÈκÎ', '', #57146, .NOT_KNOWN. ) ; +#99071 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73879 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #11162, #28579, #42411 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99073 = ORIENTED_EDGE ( 'NONE', *, *, #24396, .T. ) ; +#99072 = LINE ( 'NONE', #21071, #81981 ) ; +#99074 = CARTESIAN_POINT ( 'NONE', ( 1.353223433754789928, -0.9315058289328710384, 0.8299999999999998490 ) ) ; +#99075 = CARTESIAN_POINT ( 'NONE', ( 1.775366595766979971, -1.422222704560690110, 0.8100000000000000533 ) ) ; +#99077 = CARTESIAN_POINT ( 'NONE', ( 1.496184376687780260, -1.336216925617480067, 0.8100000000000000533 ) ) ; +#99076 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#99078 = CARTESIAN_POINT ( 'NONE', ( -0.2082825270039647125, -1.013395369748096408, 0.8100000000002263167 ) ) ; +#99079 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99080 = ORIENTED_EDGE ( 'NONE', *, *, #95805, .F. ) ; +#99081 = LINE ( 'NONE', #15385, #76157 ) ; +#99082 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99083 = AXIS2_PLACEMENT_3D ( 'NONE', #22248, #76880, #23269 ) ; +#99084 = VECTOR ( 'NONE', #8203, 1000.000000000000000 ) ; +#99085 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #86064, #78415, #63119, #49817 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99086 = FILL_AREA_STYLE_COLOUR ( '', #24099 ) ; +#99088 = CARTESIAN_POINT ( 'NONE', ( 1.580074546203000141, -1.378252124432310044, 0.8299999999999999600 ) ) ; +#99087 = CARTESIAN_POINT ( 'NONE', ( 0.4671228747608590082, -1.059049811218969905, 0.8100000000000000533 ) ) ; +#99089 = CARTESIAN_POINT ( 'NONE', ( 8.559863499500051987, 2.134644500499951913, 0.8991599999999999593 ) ) ; +#99090 = DIRECTION ( 'NONE', ( -0.7071067819560475920, -0.7071067804170475535, 0.000000000000000000 ) ) ; +#99091 = EDGE_CURVE ( 'NONE', #83217, #46959, #92202, .T. ) ; +#99092 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99093 = EDGE_CURVE ( 'NONE', #72845, #87713, #48113, .T. ) ; +#99094 = FILL_AREA_STYLE ('',( #69013 ) ) ; +#99095 = ORIENTED_EDGE ( 'NONE', *, *, #56599, .T. ) ; +#99096 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99097 = SURFACE_SIDE_STYLE ('',( #50872 ) ) ; +#99098 = SURFACE_SIDE_STYLE ('',( #13337 ) ) ; +#99099 = ORIENTED_EDGE ( 'NONE', *, *, #62098, .F. ) ; +#99100 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#99101 = CIRCLE ( 'NONE', #63377, 0.01000000000000002623 ) ; +#99103 = CARTESIAN_POINT ( 'NONE', ( 5.750000000000000000, 0.2500000000000000000, 0.000000000000000000 ) ) ; +#99102 = FILL_AREA_STYLE ('',( #100566 ) ) ; +#99104 = VECTOR ( 'NONE', #51366, 1000.000000000000000 ) ; +#99105 = SURFACE_STYLE_USAGE ( .BOTH. , #58441 ) ; +#99106 = VECTOR ( 'NONE', #51912, 1000.000000000000000 ) ; +#99107 = EDGE_CURVE ( 'NONE', #31980, #741, #36993, .T. ) ; +#99108 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #55219 ) ) ; +#99109 = SURFACE_STYLE_USAGE ( .BOTH. , #5726 ) ; +#99110 = CARTESIAN_POINT ( 'NONE', ( 9.797299999999999898, 8.236976000000000298, 0.8991599999999999593 ) ) ; +#99111 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64981 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65504, #80865, #10807 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99112 = ORIENTED_EDGE ( 'NONE', *, *, #50163, .T. ) ; +#99113 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#99114 = SURFACE_STYLE_FILL_AREA ( #53255 ) ; +#99115 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99116 = SURFACE_SIDE_STYLE ('',( #14896 ) ) ; +#99117 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#99118 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#99119 = LINE ( 'NONE', #91544, #53102 ) ; +#99120 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99121 = STYLED_ITEM ( 'NONE', ( #90272 ), #50624 ) ; +#99122 = CARTESIAN_POINT ( 'NONE', ( 3.666685000000000194, 7.848067000000000348, 0.8991599999999999593 ) ) ; +#99123 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#99124 = FACE_OUTER_BOUND ( 'NONE', #60842, .T. ) ; +#99125 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #64283, 'distance_accuracy_value', 'NONE'); +#99126 = STYLED_ITEM ( 'NONE', ( #19210 ), #15181 ) ; +#99127 = EDGE_CURVE ( 'NONE', #57506, #22415, #86922, .T. ) ; +#99128 = LINE ( 'NONE', #83897, #72977 ) ; +#99129 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #40575 ) ) ; +#99130 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99131 = ORIENTED_EDGE ( 'NONE', *, *, #32169, .T. ) ; +#99132 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99133 = ORIENTED_EDGE ( 'NONE', *, *, #53432, .T. ) ; +#99134 = CARTESIAN_POINT ( 'NONE', ( 7.386066000000000464, 6.971255000000000202, 0.8648700000000000276 ) ) ; +#99135 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #69847, 'distance_accuracy_value', 'NONE'); +#99136 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #82453, 'distance_accuracy_value', 'NONE'); +#99137 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47031 ) ) ; +#99138 = CARTESIAN_POINT ( 'NONE', ( 1.084155851675350002, -0.9900689134305371564, 0.8100000000000000533 ) ) ; +#99139 = CARTESIAN_POINT ( 'NONE', ( 0.01000000000000005745, 0.5199999999764691738, 0.6999285677606424949 ) ) ; +#99140 = PRESENTATION_STYLE_ASSIGNMENT (( #61955 ) ) ; +#99141 = CARTESIAN_POINT ( 'NONE', ( 2.449293598329944893E-17, 0.2799999999751889845, -0.2000000000066392836 ) ) ; +#99142 = SURFACE_STYLE_USAGE ( .BOTH. , #77754 ) ; +#99143 = CARTESIAN_POINT ( 'NONE', ( 1.714851922897540071, -0.9003478538782040408, 0.8100000000000000533 ) ) ; +#99144 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99145 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, 0.2850000000000000311, 0.1399999999999991807 ) ) ; +#99146 = VERTEX_POINT ( 'NONE', #63463 ) ; +#99147 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99148 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40558, 'distance_accuracy_value', 'NONE'); +#99149 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #46022, #77201, #38421, #100561 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99150 = STYLED_ITEM ( 'NONE', ( #60819 ), #81480 ) ; +#99151 = AXIS2_PLACEMENT_3D ( 'NONE', #2472, #9539, #33630 ) ; +#99152 = ORIENTED_EDGE ( 'NONE', *, *, #13848, .T. ) ; +#99153 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99154 = VECTOR ( 'NONE', #76498, 1000.000000000000000 ) ; +#99155 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42199 ) ) ; +#99156 = EDGE_CURVE ( 'NONE', #50925, #93318, #55783, .T. ) ; +#99157 = PLANE ( 'NONE', #70117 ) ; +#99158 = CARTESIAN_POINT ( 'NONE', ( -1.313637677578630036, -1.335706927508150121, 0.8100000000000000533 ) ) ; +#99159 = DIRECTION ( 'NONE', ( -0.7071067789140474957, -0.7071067834590476497, 0.000000000000000000 ) ) ; +#99160 = CARTESIAN_POINT ( 'NONE', ( 1.899999999999999911, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#99161 = VERTEX_POINT ( 'NONE', #8205 ) ; +#99162 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99163 = LINE ( 'NONE', #160, #61953 ) ; +#99164 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #87408, 'distance_accuracy_value', 'NONE'); +#99165 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42207 ), #58558 ) ; +#99166 = VECTOR ( 'NONE', #63829, 1000.000000000000114 ) ; +#99167 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99168 = CARTESIAN_POINT ( 'NONE', ( 1.585431502668919856, -1.054251812769849916, 0.8099999999999994982 ) ) ; +#99169 = EDGE_CURVE ( 'NONE', #30702, #42861, #30244, .T. ) ; +#99170 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #83010 ) ) ; +#99171 = EDGE_LOOP ( 'NONE', ( #1434, #88248, #91537, #70202, #11163, #20436 ) ) ; +#99172 = VECTOR ( 'NONE', #86694, 1000.000000000000000 ) ; +#99173 = FILL_AREA_STYLE ('',( #13407 ) ) ; +#99174 = SURFACE_SIDE_STYLE ('',( #83940 ) ) ; +#99175 = AXIS2_PLACEMENT_3D ( 'NONE', #61550, #50513, #30339 ) ; +#99176 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99177 = ORIENTED_EDGE ( 'NONE', *, *, #65086, .F. ) ; +#99178 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #97622 ), #87896 ) ; +#99179 = VECTOR ( 'NONE', #94164, 1000.000000000000000 ) ; +#99180 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14951 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #93609, #85994, #17040 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99181 = ORIENTED_EDGE ( 'NONE', *, *, #69457, .F. ) ; +#99183 = ORIENTED_EDGE ( 'NONE', *, *, #50113, .F. ) ; +#99182 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99184 = LINE ( 'NONE', #66617, #8280 ) ; +#99186 = PRESENTATION_STYLE_ASSIGNMENT (( #67117 ) ) ; +#99185 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990141, 1.899999999999999911, -0.02000000000000000042 ) ) ; +#99187 = CARTESIAN_POINT ( 'NONE', ( -2.700000000000000178, 3.123820061220085265, 0.000000000000000000 ) ) ; +#99188 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999999889, 0.2750000000000000222, 0.000000000000000000 ) ) ; +#99189 = ORIENTED_EDGE ( 'NONE', *, *, #66433, .F. ) ; +#99190 = ORIENTED_EDGE ( 'NONE', *, *, #54724, .F. ) ; +#99191 = FILL_AREA_STYLE_COLOUR ( '', #33485 ) ; +#99192 = FILL_AREA_STYLE ('',( #19148 ) ) ; +#99193 = FILL_AREA_STYLE_COLOUR ( '', #79230 ) ; +#99194 = EDGE_LOOP ( 'NONE', ( #31119, #84598, #82724, #87935 ) ) ; +#99196 = SURFACE_STYLE_FILL_AREA ( #84958 ) ; +#99195 = FACE_OUTER_BOUND ( 'NONE', #2029, .T. ) ; +#99197 = ORIENTED_EDGE ( 'NONE', *, *, #98870, .F. ) ; +#99198 = EDGE_CURVE ( 'NONE', #69178, #54838, #9218, .T. ) ; +#99199 = EDGE_CURVE ( 'NONE', #23563, #33508, #61440, .T. ) ; +#99200 = VECTOR ( 'NONE', #45546, 1000.000000000000000 ) ; +#99201 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99202 = SURFACE_STYLE_FILL_AREA ( #84961 ) ; +#99203 = CARTESIAN_POINT ( 'NONE', ( 10.71995599999999982, 2.283599999999999852, 0.8991599999999999593 ) ) ; +#99204 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99205 = PLANE ( 'NONE', #24649 ) ; +#99206 = VERTEX_POINT ( 'NONE', #47092 ) ; +#99207 = FACE_OUTER_BOUND ( 'NONE', #1708, .T. ) ; +#99208 = ORIENTED_EDGE ( 'NONE', *, *, #917, .F. ) ; +#99209 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 10.98250200000000021, 0.8991599999999999593 ) ) ; +#99210 = SURFACE_SIDE_STYLE ('',( #28845 ) ) ; +#99211 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99212 = EDGE_CURVE ( 'NONE', #17990, #67739, #77221, .T. ) ; +#99213 = FACE_OUTER_BOUND ( 'NONE', #84817, .T. ) ; +#99214 = ADVANCED_FACE ( 'NONE', ( #38441 ), #93519, .T. ) ; +#99215 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #14534 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #65705, #89688, #3911 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99216 = STYLED_ITEM ( 'NONE', ( #80983 ), #75386 ) ; +#99217 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#99218 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 14.04677200000000070, 0.8991599999999999593 ) ) ; +#99219 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99220 = LINE ( 'NONE', #21698, #98352 ) ; +#99221 = AXIS2_PLACEMENT_3D ( 'NONE', #66681, #58076, #2917 ) ; +#99222 = ORIENTED_EDGE ( 'NONE', *, *, #8854, .F. ) ; +#99223 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000533, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#99224 = LINE ( 'NONE', #77837, #61166 ) ; +#99226 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99225 = LINE ( 'NONE', #61549, #54478 ) ; +#99227 = VECTOR ( 'NONE', #62505, 1000.000000000000000 ) ; +#99228 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99229 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99230 = AXIS2_PLACEMENT_3D ( 'NONE', #100001, #61351, #29657 ) ; +#99231 = CARTESIAN_POINT ( 'NONE', ( -1.309030937367239966, -1.351519064127929992, 0.8299999999999998490 ) ) ; +#99232 = PRESENTATION_STYLE_ASSIGNMENT (( #36058 ) ) ; +#99233 = VECTOR ( 'NONE', #66198, 1000.000000000000000 ) ; +#99234 = SURFACE_SIDE_STYLE ('',( #86394 ) ) ; +#99235 = FILL_AREA_STYLE_COLOUR ( '', #86910 ) ; +#99237 = EDGE_LOOP ( 'NONE', ( #93226, #27228, #95342, #64569 ) ) ; +#99236 = VECTOR ( 'NONE', #100146, 1000.000000000000114 ) ; +#99238 = FILL_AREA_STYLE_COLOUR ( '', #86377 ) ; +#99239 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #77988 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #96334, #26435, #33081 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99240 = CARTESIAN_POINT ( 'NONE', ( 5.413237999999999772, 3.852914000000000172, 0.8991599999999999593 ) ) ; +#99241 = CARTESIAN_POINT ( 'NONE', ( 0.1714285714285699869, -1.110389610389610038, 0.8100000000000000533 ) ) ; +#99242 = PRESENTATION_STYLE_ASSIGNMENT (( #38553 ) ) ; +#99243 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99244 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99245 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99246 = FACE_OUTER_BOUND ( 'NONE', #23547, .T. ) ; +#99247 = SURFACE_SIDE_STYLE ('',( #61059 ) ) ; +#99248 = LINE ( 'NONE', #61061, #14154 ) ; +#99249 = CARTESIAN_POINT ( 'NONE', ( 0.2500000000000000000, -0.01500000000000000465, -0.2400000000000000189 ) ) ; +#99250 = FILL_AREA_STYLE ('',( #68172 ) ) ; +#99251 = ADVANCED_FACE ( 'NONE', ( #18964 ), #64939, .T. ) ; +#99252 = SURFACE_STYLE_USAGE ( .BOTH. , #70188 ) ; +#99253 = SURFACE_STYLE_USAGE ( .BOTH. , #39571 ) ; +#99254 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99255 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #21077 ) ) ; +#99256 = EDGE_CURVE ( 'NONE', #33894, #61035, #72104, .T. ) ; +#99257 = DIRECTION ( 'NONE', ( 0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#99258 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #86296 ) ) ; +#99259 = CARTESIAN_POINT ( 'NONE', ( -0.6499999999999990230, 3.099999999999989875, -0.02000000000000000042 ) ) ; +#99260 = SURFACE_STYLE_USAGE ( .BOTH. , #69157 ) ; +#99261 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #59246, 'distance_accuracy_value', 'NONE'); +#99262 = LINE ( 'NONE', #6356, #85356 ) ; +#99263 = FILL_AREA_STYLE ('',( #53391 ) ) ; +#99264 = CARTESIAN_POINT ( 'NONE', ( -0.1330377395154810072, -0.9004049383407729534, 0.8300000000000009592 ) ) ; +#99265 = SURFACE_STYLE_USAGE ( .BOTH. , #76875 ) ; +#99266 = VECTOR ( 'NONE', #83627, 1000.000000000000000 ) ; +#99267 = PLANE ( 'NONE', #32489 ) ; +#99268 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99269 = VERTEX_POINT ( 'NONE', #18455 ) ; +#99270 = PRODUCT_DEFINITION ( 'δ֪', '', #64920, #73869 ) ; +#99271 = LINE ( 'NONE', #14035, #37260 ) ; +#99272 = CARTESIAN_POINT ( 'NONE', ( 4.429999999999999716, -8.400000000000000355, -13.35000000000000142 ) ) ; +#99273 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91031, 'distance_accuracy_value', 'NONE'); +#99274 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99275 = CARTESIAN_POINT ( 'NONE', ( -1.300000000000000266, -3.149999999999990141, -0.02000000000000000042 ) ) ; +#99276 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99277 = CARTESIAN_POINT ( 'NONE', ( -1.700000000000000178, -3.123820061220085265, -0.02000000000000000042 ) ) ; +#99278 = STYLED_ITEM ( 'NONE', ( #62966 ), #15516 ) ; +#99279 = DIRECTION ( 'NONE', ( -1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#99280 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#99281 = EDGE_CURVE ( 'NONE', #86902, #9771, #41974, .T. ) ; +#99282 = ORIENTED_EDGE ( 'NONE', *, *, #88829, .F. ) ; +#99283 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99284 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #52851, 'distance_accuracy_value', 'NONE'); +#99285 = CARTESIAN_POINT ( 'NONE', ( -0.1098982853935999981, -1.445363849546990043, 0.8300000000000006262 ) ) ; +#99286 = PRESENTATION_STYLE_ASSIGNMENT (( #37108 ) ) ; +#99287 = EDGE_CURVE ( 'NONE', #49837, #5565, #27096, .T. ) ; +#99288 = ORIENTED_EDGE ( 'NONE', *, *, #8085, .F. ) ; +#99289 = EDGE_LOOP ( 'NONE', ( #94373, #74672, #90591, #80794 ) ) ; +#99291 = SURFACE_SIDE_STYLE ('',( #44233 ) ) ; +#99290 = CARTESIAN_POINT ( 'NONE', ( 0.3880979930239000231, -0.9663965808142249703, 0.8300000000000002931 ) ) ; +#99292 = VECTOR ( 'NONE', #10352, 1000.000000000000000 ) ; +#99293 = ORIENTED_EDGE ( 'NONE', *, *, #48382, .F. ) ; +#99294 = EDGE_CURVE ( 'NONE', #56731, #2598, #96554, .T. ) ; +#99295 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000444, 1.899999999999996136, 2.990963115645192065E-79 ) ) ; +#99297 = CYLINDRICAL_SURFACE ( 'NONE', #45150, 0.4690439894930241160 ) ; +#99296 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #24311, #94191, #56473, #77893 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99298 = SURFACE_STYLE_FILL_AREA ( #30406 ) ; +#99299 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #80084, #10017 ), + ( #41280, #64740 ), + ( #72385, #95856 ), + ( #25966, #57113 ), + ( #88237, #18242 ), + ( #10505, #44248 ), + ( #91232, #45236 ), + ( #28945, #37128 ), + ( #13546, #6877 ), + ( #60136, #90732 ), + ( #13048, #92220 ), + ( #21281, #75409 ), + ( #28456, #5421 ), + ( #97833, #66734 ), + ( #27975, #61120 ), + ( #52442, #59136 ), + ( #29932, #51463 ), + ( #22286, #36636 ), + ( #20269, #52954 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07237848055891020482, 0.1407192550564320133, 0.2049521751864399888, 0.2662164852627100231, 0.3253698271746789938, 0.3835875598417520238, 0.4415017690754730051, 0.4993597690990220217, 0.5575367350798919874, 0.6164546912842580051, 0.6759371479080940048, 0.7372987486091709952, 0.8002568593343240000, 0.8649063342747660421, 0.9311109296293520465, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99300 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #24545 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79908, #2788, #65072 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99301 = ORIENTED_EDGE ( 'NONE', *, *, #49392, .T. ) ; +#99302 = EDGE_CURVE ( 'NONE', #56505, #18334, #57825, .T. ) ; +#99303 = VECTOR ( 'NONE', #30193, 1000.000000000000000 ) ; +#99304 = ORIENTED_EDGE ( 'NONE', *, *, #30783, .F. ) ; +#99305 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99307 = SURFACE_SIDE_STYLE ('',( #75912 ) ) ; +#99306 = FILL_AREA_STYLE_COLOUR ( '', #29702 ) ; +#99308 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99309 = VECTOR ( 'NONE', #29160, 1000.000000000000000 ) ; +#99310 = AXIS2_PLACEMENT_3D ( 'NONE', #81957, #66605, #90088 ) ; +#99311 = LINE ( 'NONE', #69202, #1703 ) ; +#99312 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #47282 ) ) ; +#99313 = CARTESIAN_POINT ( 'NONE', ( -1.371428571428570109, -1.059983766233770108, 0.8299999999999999600 ) ) ; +#99314 = ORIENTED_EDGE ( 'NONE', *, *, #32648, .F. ) ; +#99315 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99316 = VERTEX_POINT ( 'NONE', #1660 ) ; +#99317 = EDGE_CURVE ( 'NONE', #1768, #65042, #58326, .T. ) ; +#99318 = ORIENTED_EDGE ( 'NONE', *, *, #43923, .F. ) ; +#99319 = EDGE_CURVE ( 'NONE', #67213, #60900, #56813, .T. ) ; +#99320 = CARTESIAN_POINT ( 'NONE', ( 0.9855976085564051026, -1.097307480365639965, 0.8299999999999999600 ) ) ; +#99322 = CARTESIAN_POINT ( 'NONE', ( 3.098800000000000221, 11.30020599999999931, 0.8991599999999999593 ) ) ; +#99321 = FACE_OUTER_BOUND ( 'NONE', #30695, .T. ) ; +#99323 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87978 ) ) ; +#99324 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #71726 ), #68421 ) ; +#99326 = ORIENTED_EDGE ( 'NONE', *, *, #73257, .T. ) ; +#99325 = FILL_AREA_STYLE ('',( #61643 ) ) ; +#99327 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #25800 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38275, #93844, #86228 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99329 = AXIS2_PLACEMENT_3D ( 'NONE', #52880, #5847, #14512 ) ; +#99328 = PLANE ( 'NONE', #40180 ) ; +#99330 = LINE ( 'NONE', #45254, #54792 ) ; +#99331 = DIRECTION ( 'NONE', ( 0.7071067804170475535, -0.7071067819560475920, 0.000000000000000000 ) ) ; +#99332 = VERTEX_POINT ( 'NONE', #17441 ) ; +#99334 = FILL_AREA_STYLE ('',( #99796 ) ) ; +#99333 = LINE ( 'NONE', #29473, #7339 ) ; +#99335 = ORIENTED_EDGE ( 'NONE', *, *, #19058, .F. ) ; +#99336 = VERTEX_POINT ( 'NONE', #42957 ) ; +#99337 = CARTESIAN_POINT ( 'NONE', ( 0.9886343406507150933, -1.414598001867640065, 0.8100000000000000533 ) ) ; +#99338 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.175494350822289960E-30, 1.000000000000000000 ) ) ; +#99339 = EDGE_CURVE ( 'NONE', #54849, #52467, #7581, .T. ) ; +#99340 = SURFACE_STYLE_USAGE ( .BOTH. , #36669 ) ; +#99341 = EDGE_CURVE ( 'NONE', #88894, #93881, #87913, .T. ) ; +#99342 = CARTESIAN_POINT ( 'NONE', ( -0.01281341696057500083, -1.096743473147149928, 0.8299999999999999600 ) ) ; +#99343 = VERTEX_POINT ( 'NONE', #49134 ) ; +#99344 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#99345 = VERTEX_POINT ( 'NONE', #80276 ) ; +#99346 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99347 = CARTESIAN_POINT ( 'NONE', ( 1.068409529932820012, -1.093211113524890088, 0.8100000000000000533 ) ) ; +#99348 = DIRECTION ( 'NONE', ( 0.9584246665703162193, -0.2853456824793011437, 0.000000000000000000 ) ) ; +#99349 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99350 = SURFACE_STYLE_USAGE ( .BOTH. , #99826 ) ; +#99351 = ORIENTED_EDGE ( 'NONE', *, *, #13597, .F. ) ; +#99352 = EDGE_CURVE ( 'NONE', #35029, #58057, #10202, .T. ) ; +#99353 = FILL_AREA_STYLE_COLOUR ( '', #4864 ) ; +#99354 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99355 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, 0.2499999999999990286, 0.000000000000000000 ) ) ; +#99356 = STYLED_ITEM ( 'NONE', ( #68934 ), #33287 ) ; +#99357 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99358 = PRESENTATION_STYLE_ASSIGNMENT (( #21848 ) ) ; +#99359 = SURFACE_STYLE_FILL_AREA ( #76465 ) ; +#99360 = PRESENTATION_STYLE_ASSIGNMENT (( #100824 ) ) ; +#99361 = FILL_AREA_STYLE ('',( #75474 ) ) ; +#99362 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1601 ), #53755 ) ; +#99363 = STYLED_ITEM ( 'NONE', ( #10571 ), #95117 ) ; +#99364 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99365 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 5.400000000000000355, 0.03429000000000000103 ) ) ; +#99366 = EDGE_CURVE ( 'NONE', #21432, #60527, #80881, .T. ) ; +#99367 = LINE ( 'NONE', #5001, #15934 ) ; +#99368 = SURFACE_STYLE_FILL_AREA ( #68304 ) ; +#99369 = AXIS2_PLACEMENT_3D ( 'NONE', #77897, #22263, #14557 ) ; +#99370 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99371 = VECTOR ( 'NONE', #53717, 1000.000000000000000 ) ; +#99372 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #91672, 'distance_accuracy_value', 'NONE'); +#99373 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53841 ), #9743 ) ; +#99374 = SURFACE_STYLE_FILL_AREA ( #21353 ) ; +#99375 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#99376 = ORIENTED_EDGE ( 'NONE', *, *, #49230, .F. ) ; +#99377 = FILL_AREA_STYLE_COLOUR ( '', #1305 ) ; +#99378 = DIRECTION ( 'NONE', ( 0.7071067811865514585, 0.7071067811865435759, 0.000000000000000000 ) ) ; +#99379 = SURFACE_STYLE_FILL_AREA ( #59216 ) ; +#99380 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34539, 'distance_accuracy_value', 'NONE'); +#99381 = AXIS2_PLACEMENT_3D ( 'NONE', #88296, #33164, #81158 ) ; +#99382 = SURFACE_SIDE_STYLE ('',( #85663 ) ) ; +#99383 = CARTESIAN_POINT ( 'NONE', ( 3.277775000000000105, 6.539920000000000400, 0.8648700000000000276 ) ) ; +#99384 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99385 = VECTOR ( 'NONE', #30459, 1000.000000000000000 ) ; +#99386 = VERTEX_POINT ( 'NONE', #67918 ) ; +#99387 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8495 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22732, #84998, #100209 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99388 = FILL_AREA_STYLE ('',( #36214 ) ) ; +#99389 = PLANE ( 'NONE', #49747 ) ; +#99390 = FACE_OUTER_BOUND ( 'NONE', #87653, .T. ) ; +#99391 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99392 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #37382, 'distance_accuracy_value', 'NONE'); +#99393 = FACE_OUTER_BOUND ( 'NONE', #73056, .T. ) ; +#99394 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #84554, 'distance_accuracy_value', 'NONE'); +#99395 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99396 = SURFACE_SIDE_STYLE ('',( #21376 ) ) ; +#99397 = EDGE_CURVE ( 'NONE', #15767, #58927, #35742, .T. ) ; +#99398 = VERTEX_POINT ( 'NONE', #60816 ) ; +#99399 = EDGE_LOOP ( 'NONE', ( #15049, #83447, #85178, #17729 ) ) ; +#99400 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60400 ), #66917 ) ; +#99401 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99402 = VERTEX_POINT ( 'NONE', #28643 ) ; +#99403 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99404 = CARTESIAN_POINT ( 'NONE', ( 6.599999999999999645, 15.15000000000000036, 0.000000000000000000 ) ) ; +#99405 = CARTESIAN_POINT ( 'NONE', ( -1.099999999999999867, -3.500000000000000444, 0.000000000000000000 ) ) ; +#99406 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99407 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 8.750000000000000000, 0.000000000000000000 ) ) ; +#99408 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99409 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #12897 ) ; +#99410 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#99411 = CARTESIAN_POINT ( 'NONE', ( -0.3894195008773166933, 1.245410019500388321, 0.8100000000000001643 ) ) ; +#99413 = ORIENTED_EDGE ( 'NONE', *, *, #57745, .T. ) ; +#99412 = ORIENTED_EDGE ( 'NONE', *, *, #40, .T. ) ; +#99414 = EDGE_CURVE ( 'NONE', #77948, #53678, #36814, .T. ) ; +#99415 = AXIS2_PLACEMENT_3D ( 'NONE', #42386, #96963, #73521 ) ; +#99416 = ORIENTED_EDGE ( 'NONE', *, *, #86107, .T. ) ; +#99417 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99419 = LINE ( 'NONE', #44856, #95197 ) ; +#99418 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99420 = VERTEX_POINT ( 'NONE', #58828 ) ; +#99421 = ADVANCED_FACE ( 'NONE', ( #90422 ), #83782, .F. ) ; +#99422 = ORIENTED_EDGE ( 'NONE', *, *, #7612, .T. ) ; +#99423 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99424 = CARTESIAN_POINT ( 'NONE', ( -0.2958578643762690419, -0.004999999999999959338, -0.1499999999999999944 ) ) ; +#99425 = AXIS2_PLACEMENT_3D ( 'NONE', #3449, #65726, #2938 ) ; +#99427 = LINE ( 'NONE', #52575, #13971 ) ; +#99426 = CARTESIAN_POINT ( 'NONE', ( 8.904363999999999280, 11.78243800000000086, 0.8991599999999999593 ) ) ; +#99428 = VERTEX_POINT ( 'NONE', #84277 ) ; +#99429 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99430 = ORIENTED_EDGE ( 'NONE', *, *, #69943, .T. ) ; +#99431 = ADVANCED_FACE ( 'NONE', ( #99492 ), #14272, .T. ) ; +#99432 = VERTEX_POINT ( 'NONE', #12748 ) ; +#99433 = EDGE_CURVE ( 'NONE', #26181, #63753, #93403, .T. ) ; +#99434 = SURFACE_STYLE_FILL_AREA ( #5561 ) ; +#99435 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94195 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #45742, #38626, #46769 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99436 = AXIS2_PLACEMENT_3D ( 'NONE', #5925, #21298, #6893 ) ; +#99437 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99441 = EDGE_CURVE ( 'NONE', #86094, #27316, #504, .T. ) ; +#99440 = ORIENTED_EDGE ( 'NONE', *, *, #815, .T. ) ; +#99439 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #73201, 'distance_accuracy_value', 'NONE'); +#99438 = CARTESIAN_POINT ( 'NONE', ( -0.1142045454545460026, -1.445454545454550210, 0.8099999999998321876 ) ) ; +#99442 = EDGE_CURVE ( 'NONE', #32273, #69332, #8080, .T. ) ; +#99443 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #58766 ) ) ; +#99444 = PRESENTATION_STYLE_ASSIGNMENT (( #44382 ) ) ; +#99445 = VERTEX_POINT ( 'NONE', #70446 ) ; +#99446 = AXIS2_PLACEMENT_3D ( 'NONE', #56725, #87323, #41885 ) ; +#99447 = CARTESIAN_POINT ( 'NONE', ( 0.01546163603480650052, -1.327673353236110021, 0.8100000000000000533 ) ) ; +#99448 = SURFACE_STYLE_USAGE ( .BOTH. , #51100 ) ; +#99449 = ORIENTED_EDGE ( 'NONE', *, *, #94829, .F. ) ; +#99450 = EDGE_LOOP ( 'NONE', ( #79175, #30559, #84890, #2173 ) ) ; +#99451 = LINE ( 'NONE', #60766, #7854 ) ; +#99452 = VECTOR ( 'NONE', #46751, 1000.000000000000000 ) ; +#99453 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999960121, -0.6500000000000001332, -0.02000000000000000042 ) ) ; +#99454 = FILL_AREA_STYLE_COLOUR ( '', #59608 ) ; +#99455 = ADVANCED_FACE ( 'NONE', ( #8577 ), #68914, .T. ) ; +#99456 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#99457 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99458 = FILL_AREA_STYLE ('',( #93356 ) ) ; +#99459 = EDGE_CURVE ( 'NONE', #90078, #2533, #99980, .T. ) ; +#99460 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99461 = VECTOR ( 'NONE', #4866, 1000.000000000000114 ) ; +#99462 = VERTEX_POINT ( 'NONE', #61328 ) ; +#99463 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #86183 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #12858, #20585, #84873 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99464 = CARTESIAN_POINT ( 'NONE', ( -1.084303872719659889, -1.510436674894549913, 0.8100000000000000533 ) ) ; +#99465 = ORIENTED_EDGE ( 'NONE', *, *, #67131, .T. ) ; +#99466 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78295 ) ) ; +#99467 = CARTESIAN_POINT ( 'NONE', ( -0.4899999999999999911, -0.005000000000000000104, -0.2400000000000000189 ) ) ; +#99468 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99469 = CARTESIAN_POINT ( 'NONE', ( -0.1999999999999999833, -0.02000000000000000042, 0.1499999999999999944 ) ) ; +#99470 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #75857, #37083, #68180, #99259 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99471 = CARTESIAN_POINT ( 'NONE', ( 1.708426850688339993, -1.163903542943879987, 0.8100000000000000533 ) ) ; +#99472 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99473 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99474 = LINE ( 'NONE', #15265, #36414 ) ; +#99475 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99476 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#99477 = CARTESIAN_POINT ( 'NONE', ( -3.000000000000000000, 3.000000000000000000, 0.8299999999999999600 ) ) ; +#99478 = AXIS2_PLACEMENT_3D ( 'NONE', #7651, #85341, #70020 ) ; +#99479 = SURFACE_STYLE_USAGE ( .BOTH. , #21968 ) ; +#99480 = EDGE_CURVE ( 'NONE', #73910, #53059, #14777, .T. ) ; +#99482 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #8253 ) ) ; +#99481 = SURFACE_STYLE_FILL_AREA ( #14262 ) ; +#99484 = ADVANCED_FACE ( 'NONE', ( #76604 ), #7579, .F. ) ; +#99483 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #34971, 'distance_accuracy_value', 'NONE'); +#99485 = ORIENTED_EDGE ( 'NONE', *, *, #80316, .F. ) ; +#99486 = FILL_AREA_STYLE_COLOUR ( '', #11679 ) ; +#99487 = PRESENTATION_STYLE_ASSIGNMENT (( #84274 ) ) ; +#99488 = CARTESIAN_POINT ( 'NONE', ( 1.449999999999999956, -3.149999999999970157, -0.02000000000000000042 ) ) ; +#99489 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.2500000000000000000 ) ) ; +#99490 = LINE ( 'NONE', #99978, #51972 ) ; +#99491 = PLANE ( 'NONE', #53512 ) ; +#99492 = FACE_OUTER_BOUND ( 'NONE', #21370, .T. ) ; +#99493 = AXIS2_PLACEMENT_3D ( 'NONE', #31302, #78774, #47127 ) ; +#99494 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.899999999999999911, 0.8299999999999999600 ) ) ; +#99495 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99496 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100938 ) ; +#99497 = STYLED_ITEM ( 'NONE', ( #22867 ), #95216 ) ; +#99498 = SURFACE_STYLE_FILL_AREA ( #94305 ) ; +#99499 = EDGE_LOOP ( 'NONE', ( #6955, #61451, #34338, #24324 ) ) ; +#99500 = SURFACE_STYLE_USAGE ( .BOTH. , #46974 ) ; +#99501 = EDGE_CURVE ( 'NONE', #80977, #9763, #69448, .T. ) ; +#99502 = EDGE_LOOP ( 'NONE', ( #6199, #67314, #69526, #42483 ) ) ; +#99503 = FILL_AREA_STYLE ('',( #92421 ) ) ; +#99504 = VECTOR ( 'NONE', #15889, 1000.000000000000000 ) ; +#99505 = SURFACE_SIDE_STYLE ('',( #51158 ) ) ; +#99506 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99507 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99508 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.2999999999999999889, 1.048695503451051965E-76 ) ) ; +#99509 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8648700000000000276 ) ) ; +#99510 = SURFACE_STYLE_FILL_AREA ( #52170 ) ; +#99511 = CARTESIAN_POINT ( 'NONE', ( -0.2325547191045798101, -0.9373990620188800138, 0.8100000000003397815 ) ) ; +#99512 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99513 = ORIENTED_EDGE ( 'NONE', *, *, #55476, .T. ) ; +#99514 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99516 = EDGE_CURVE ( 'NONE', #93065, #93750, #97310, .T. ) ; +#99515 = LINE ( 'NONE', #59857, #76496 ) ; +#99517 = ORIENTED_EDGE ( 'NONE', *, *, #39575, .F. ) ; +#99518 = LINE ( 'NONE', #13784, #50714 ) ; +#99519 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99520 = CIRCLE ( 'NONE', #42566, 0.1200000000000000927 ) ; +#99521 = ORIENTED_EDGE ( 'NONE', *, *, #991, .F. ) ; +#99522 = SURFACE_STYLE_USAGE ( .BOTH. , #68459 ) ; +#99523 = FACE_OUTER_BOUND ( 'NONE', #71929, .T. ) ; +#99524 = LINE ( 'NONE', #84792, #83764 ) ; +#99525 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #19758 ), #76807 ) ; +#99526 = FILL_AREA_STYLE_COLOUR ( '', #43612 ) ; +#99527 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99528 = SURFACE_STYLE_USAGE ( .BOTH. , #59371 ) ; +#99529 = VECTOR ( 'NONE', #15751, 1000.000000000000000 ) ; +#99531 = ORIENTED_EDGE ( 'NONE', *, *, #46011, .F. ) ; +#99530 = ORIENTED_EDGE ( 'NONE', *, *, #1282, .T. ) ; +#99532 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #78741 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #91363, #36257, #42898 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99533 = SURFACE_SIDE_STYLE ('',( #75644 ) ) ; +#99534 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99535 = VERTEX_POINT ( 'NONE', #74869 ) ; +#99536 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99538 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999950173, -2.100000000000000089, -0.02000000000000000042 ) ) ; +#99537 = CARTESIAN_POINT ( 'NONE', ( -1.699999999999999734, 3.500000000000000444, 0.000000000000000000 ) ) ; +#99539 = ORIENTED_EDGE ( 'NONE', *, *, #17014, .F. ) ; +#99540 = VERTEX_POINT ( 'NONE', #66691 ) ; +#99541 = PRESENTATION_STYLE_ASSIGNMENT (( #90470 ) ) ; +#99542 = CARTESIAN_POINT ( 'NONE', ( 2.100000000000000089, 3.149999999999970157, -0.02000000000000000042 ) ) ; +#99543 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99544 = FILL_AREA_STYLE ('',( #54193 ) ) ; +#99546 = PLANE ( 'NONE', #22329 ) ; +#99545 = CARTESIAN_POINT ( 'NONE', ( -0.9128876696368980470, 0.4958735128372510625, 0.8100000000000000533 ) ) ; +#99547 = ORIENTED_EDGE ( 'NONE', *, *, #9437, .F. ) ; +#99548 = VERTEX_POINT ( 'NONE', #67194 ) ; +#99549 = SURFACE_STYLE_FILL_AREA ( #78670 ) ; +#99550 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #41009 ), #70260 ) ; +#99551 = ORIENTED_EDGE ( 'NONE', *, *, #36339, .T. ) ; +#99552 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#99553 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #18134 ), #24701 ) ; +#99555 = VERTEX_POINT ( 'NONE', #73870 ) ; +#99554 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#99556 = EDGE_CURVE ( 'NONE', #67425, #81345, #89190, .T. ) ; +#99557 = SURFACE_SIDE_STYLE ('',( #100530 ) ) ; +#99558 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 9.830099697201706315E-19, -0.8499999999999999778 ) ) ; +#99559 = FACE_OUTER_BOUND ( 'NONE', #26686, .T. ) ; +#99560 = ORIENTED_EDGE ( 'NONE', *, *, #37541, .T. ) ; +#99561 = SHAPE_REPRESENTATION ( 'DesignRootModel', ( #50239, #87726, #1288, #58400, #30538, #14271, #68089, #81200, #27391, #94182, #84437, #15902, #48616, #40444, #73010, #77881, #33899, #97464, #87659, #100556, #53481, #63267, #9371, #66516, #86044 ), #69700 ) ; +#99562 = CARTESIAN_POINT ( 'NONE', ( -0.7324675324675320454, -1.188311688311689984, 0.8100000000000000533 ) ) ; +#99563 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2166666666666666463, 0.000000000000000000 ) ) ; +#99564 = ORIENTED_EDGE ( 'NONE', *, *, #25317, .T. ) ; +#99565 = CARTESIAN_POINT ( 'NONE', ( 0.06997596596441089944, -1.057175192472970204, 0.8299999999999988498 ) ) ; +#99566 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99567 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #16960, #70082, #79796, #63484 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99568 = ADVANCED_FACE ( 'NONE', ( #27410 ), #4402, .T. ) ; +#99569 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #17726 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #14488, #14980, #85480 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99570 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #36082 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #72629, #33341, #11257 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99571 = EDGE_LOOP ( 'NONE', ( #47736, #25992, #96668, #36944, #8756, #87593 ) ) ; +#99572 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #57286 ) ) ; +#99573 = ADVANCED_FACE ( 'NONE', ( #27928 ), #11989, .T. ) ; +#99574 = CARTESIAN_POINT ( 'NONE', ( 1.197808441558440018, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#99575 = FILL_AREA_STYLE_COLOUR ( '', #87906 ) ; +#99576 = VECTOR ( 'NONE', #13362, 1000.000000000000000 ) ; +#99577 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 5.750000000000000000, 0.03429000000000000103 ) ) ; +#99578 = FACE_OUTER_BOUND ( 'NONE', #85976, .T. ) ; +#99579 = SURFACE_SIDE_STYLE ('',( #50377 ) ) ; +#99580 = ORIENTED_EDGE ( 'NONE', *, *, #87630, .T. ) ; +#99581 = VECTOR ( 'NONE', #35304, 1000.000000000000000 ) ; +#99582 = VECTOR ( 'NONE', #9447, 1000.000000000000000 ) ; +#99583 = LINE ( 'NONE', #14865, #22199 ) ; +#99584 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99585 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99586 = CARTESIAN_POINT ( 'NONE', ( 12.34606400000000015, 8.455799999999999983, 0.8991599999999999593 ) ) ; +#99587 = CARTESIAN_POINT ( 'NONE', ( 13.84999999999999964, 1.399999999999999911, -13.35000000000000142 ) ) ; +#99588 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99589 = CARTESIAN_POINT ( 'NONE', ( 3.822247875125043937, 8.003630875125045563, 0.8648700000000000276 ) ) ; +#99590 = VECTOR ( 'NONE', #67689, 1000.000000000000000 ) ; +#99591 = STYLED_ITEM ( 'NONE', ( #38327 ), #66103 ) ; +#99592 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99593 = ORIENTED_EDGE ( 'NONE', *, *, #42380, .T. ) ; +#99594 = PLANE ( 'NONE', #21786 ) ; +#99595 = EDGE_LOOP ( 'NONE', ( #30173, #48267, #94077, #85333 ) ) ; +#99596 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99598 = FILL_AREA_STYLE_COLOUR ( '', #20060 ) ; +#99597 = LINE ( 'NONE', #23604, #3446 ) ; +#99599 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#99600 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99601 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#99602 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99603 = EDGE_CURVE ( 'NONE', #67425, #50680, #9602, .T. ) ; +#99604 = EDGE_LOOP ( 'NONE', ( #61488, #13450, #17296, #70708 ) ) ; +#99605 = FACE_OUTER_BOUND ( 'NONE', #45966, .T. ) ; +#99606 = FACE_OUTER_BOUND ( 'NONE', #15992, .T. ) ; +#99607 = SURFACE_STYLE_USAGE ( .BOTH. , #22096 ) ; +#99608 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99609 = AXIS2_PLACEMENT_3D ( 'NONE', #5419, #35636, #14077 ) ; +#99610 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99611 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#99612 = ORIENTED_EDGE ( 'NONE', *, *, #63910, .F. ) ; +#99613 = ORIENTED_EDGE ( 'NONE', *, *, #31116, .T. ) ; +#99614 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, 0.000000000000000000 ) ) ; +#99615 = PRESENTATION_STYLE_ASSIGNMENT (( #20098 ) ) ; +#99616 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8299999999999999600 ) ) ; +#99617 = CARTESIAN_POINT ( 'NONE', ( 1.750951194234720010, -0.9053603395923379704, 0.8100000000000000533 ) ) ; +#99618 = FILL_AREA_STYLE ('',( #29292 ) ) ; +#99619 = FACE_OUTER_BOUND ( 'NONE', #83600, .T. ) ; +#99620 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999990585, 1.699999999999999734, 1.048695503451051965E-76 ) ) ; +#99621 = EDGE_LOOP ( 'NONE', ( #5793, #543, #44254, #70343 ) ) ; +#99623 = ADVANCED_FACE ( 'NONE', ( #17329 ), #58085, .T. ) ; +#99622 = FILL_AREA_STYLE_COLOUR ( '', #1456 ) ; +#99624 = CARTESIAN_POINT ( 'NONE', ( -0.5000000000000000000, -0.005000000000000000104, 0.2399999999999999911 ) ) ; +#99625 = VECTOR ( 'NONE', #71058, 1000.000000000000000 ) ; +#99626 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #49246 ), #68727 ) ; +#99627 = ORIENTED_EDGE ( 'NONE', *, *, #7103, .F. ) ; +#99628 = ADVANCED_FACE ( 'NONE', ( #52910 ), #21736, .T. ) ; +#99629 = VECTOR ( 'NONE', #68759, 1000.000000000000000 ) ; +#99630 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#99631 = CARTESIAN_POINT ( 'NONE', ( -1.316883116883120097, -1.300689935064940128, 0.8100000000000000533 ) ) ; +#99632 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99633 = APPLICATION_CONTEXT ( 'automotive_design' ) ; +#99634 = VERTEX_POINT ( 'NONE', #99730 ) ; +#99635 = FILL_AREA_STYLE ('',( #39855 ) ) ; +#99636 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99637 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99638 = VECTOR ( 'NONE', #44908, 1000.000000000000000 ) ; +#99639 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #328 ) ) ; +#99640 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#99641 = ADVANCED_FACE ( 'NONE', ( #29892 ), #69162, .T. ) ; +#99642 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #88172 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81754, #34292, #4600 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99643 = VERTEX_POINT ( 'NONE', #47744 ) ; +#99644 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#99645 = CARTESIAN_POINT ( 'NONE', ( -0.2961038961038970352, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#99646 = CARTESIAN_POINT ( 'NONE', ( 6.627799999999999692, 11.29270000000000174, 0.8991599999999999593 ) ) ; +#99647 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99648 = SURFACE_STYLE_FILL_AREA ( #50457 ) ; +#99649 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99650 = ORIENTED_EDGE ( 'NONE', *, *, #66323, .T. ) ; +#99651 = SURFACE_SIDE_STYLE ('',( #53313 ) ) ; +#99652 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #38655, 'distance_accuracy_value', 'NONE'); +#99653 = AXIS2_PLACEMENT_3D ( 'NONE', #8850, #32435, #48274 ) ; +#99654 = CIRCLE ( 'NONE', #70454, 0.09999999999999939493 ) ; +#99655 = EDGE_LOOP ( 'NONE', ( #72938, #69052, #84063, #40280 ) ) ; +#99657 = ORIENTED_EDGE ( 'NONE', *, *, #69228, .T. ) ; +#99656 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99658 = ADVANCED_FACE ( 'NONE', ( #17084 ), #41118, .F. ) ; +#99659 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #80227, 'distance_accuracy_value', 'NONE'); +#99660 = CARTESIAN_POINT ( 'NONE', ( -1.146550324675319921, -1.515584415584420030, 0.8299999999999999600 ) ) ; +#99661 = LINE ( 'NONE', #98683, #74162 ) ; +#99662 = CARTESIAN_POINT ( 'NONE', ( -0.2999999999999990452, 3.149999999999979927, -0.02000000000000000042 ) ) ; +#99663 = STYLED_ITEM ( 'NONE', ( #82925 ), #52541 ) ; +#99664 = ORIENTED_EDGE ( 'NONE', *, *, #59438, .F. ) ; +#99665 = PLANE ( 'NONE', #43464 ) ; +#99666 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99667 = ORIENTED_EDGE ( 'NONE', *, *, #29041, .T. ) ; +#99668 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99669 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99670 = SURFACE_SIDE_STYLE ('',( #8282 ) ) ; +#99671 = VECTOR ( 'NONE', #3160, 1000.000000000000000 ) ; +#99672 = ORIENTED_EDGE ( 'NONE', *, *, #100004, .T. ) ; +#99673 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #37780, #77071, #100426, #7035, #99935, #68388, #30572, #38280, #8034, #93358, #29115, #69374, #14226, #21940, #61780, #53105, #68879, #76064, #30091, #61288, #92841, #92374, #22439, #85224, #22966, #37294, #54100, #29597, #15243, #46405, #77573 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.469891172885546535E-05, 2.837247054049612594E-05, 4.118507935591348221E-05, 5.372706464234096844E-05, 6.650062454122421458E-05, 7.950671947742871896E-05, 9.319155633874893682E-05, 0.0001076114340513586814, 0.0001227165621414777984, 0.0001383963279910339851, 0.0001548135506473832508, 0.0001718948309939934160, 0.0002071828797828274100, 0.0002430624189904493488, 0.0002791349300522108653, 0.0003149324747076749425, 0.0003324498852057858572, 0.0003494012154680386454, 0.0003659898241423623685, 0.0003821226701213503761, 0.0003979326149518961925, 0.0004135471195641438535, 0.0004289298359166765213, 0.0004446306713806237338, 0.0004607306973405810740, 0.0004777166628338419497, 0.0004958116794663048081, 0.0005154722711623931043 ), + .UNSPECIFIED. ) ; +#99674 = ORIENTED_EDGE ( 'NONE', *, *, #32375, .F. ) ; +#99675 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #36261 ), #44304 ) ; +#99676 = EDGE_CURVE ( 'NONE', #22015, #76842, #1279, .T. ) ; +#99678 = CARTESIAN_POINT ( 'NONE', ( -0.1499999999999999667, 0.2500000000000000000, 0.8499999999999999778 ) ) ; +#99677 = FILL_AREA_STYLE_COLOUR ( '', #25159 ) ; +#99679 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, -3.233333333333333393, 0.000000000000000000 ) ) ; +#99680 = AXIS2_PLACEMENT_3D ( 'NONE', #64232, #18231, #95334 ) ; +#99681 = VERTEX_POINT ( 'NONE', #94681 ) ; +#99682 = ORIENTED_EDGE ( 'NONE', *, *, #48913, .T. ) ; +#99683 = FILL_AREA_STYLE_COLOUR ( '', #81333 ) ; +#99685 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99684 = FILL_AREA_STYLE_COLOUR ( '', #3740 ) ; +#99686 = SURFACE_STYLE_USAGE ( .BOTH. , #98224 ) ; +#99687 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #60693 ), #29683 ) ; +#99688 = FILL_AREA_STYLE ('',( #6784 ) ) ; +#99689 = FILL_AREA_STYLE_COLOUR ( '', #64249 ) ; +#99690 = VECTOR ( 'NONE', #98568, 1000.000000000000000 ) ; +#99691 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100966 ) ; +#99692 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#99693 = DIRECTION ( 'NONE', ( -0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#99694 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99696 = STYLED_ITEM ( 'NONE', ( #74613 ), #43163 ) ; +#99695 = CARTESIAN_POINT ( 'NONE', ( 1.328634758872640154, -1.021599245672099920, 0.8300000000000009592 ) ) ; +#99697 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99698 = ORIENTED_EDGE ( 'NONE', *, *, #70253, .F. ) ; +#99699 = CYLINDRICAL_SURFACE ( 'NONE', #25362, 0.05000000000000012768 ) ; +#99700 = DIRECTION ( 'NONE', ( -1.401985567973789257E-16, 1.000000000000000000, -2.620751377075717173E-32 ) ) ; +#99702 = SURFACE_SIDE_STYLE ('',( #69656 ) ) ; +#99701 = FILL_AREA_STYLE_COLOUR ( '', #8140 ) ; +#99703 = VECTOR ( 'NONE', #92577, 1000.000000000000000 ) ; +#99704 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #6382, 'distance_accuracy_value', 'NONE'); +#99705 = CARTESIAN_POINT ( 'NONE', ( 3.943541999999999437, 14.49753199999999964, 0.8991599999999999593 ) ) ; +#99706 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#99707 = STYLED_ITEM ( 'NONE', ( #48186 ), #11250 ) ; +#99708 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99709 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, -0.005000000000000013115, -0.2400000000000000189 ) ) ; +#99710 = ADVANCED_FACE ( 'NONE', ( #87558 ), #64085, .T. ) ; +#99711 = ORIENTED_EDGE ( 'NONE', *, *, #83192, .F. ) ; +#99712 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99713 = SURFACE_STYLE_USAGE ( .BOTH. , #30876 ) ; +#99714 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#99715 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99716 = CARTESIAN_POINT ( 'NONE', ( 8.294764000000000692, 11.30762200000000028, 0.8648700000000000276 ) ) ; +#99717 = CARTESIAN_POINT ( 'NONE', ( 2.500000000000000000, 3.149999999999959943, -0.02000000000000000042 ) ) ; +#99718 = PRESENTATION_STYLE_ASSIGNMENT (( #16549 ) ) ; +#99719 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99720 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99721 = FILL_AREA_STYLE ('',( #67182 ) ) ; +#99722 = DIRECTION ( 'NONE', ( 1.617781153285274011E-32, 1.000000000000000000, -5.551115123125780237E-17 ) ) ; +#99723 = CARTESIAN_POINT ( 'NONE', ( 7.739619127034740309, 10.45022087296526081, 0.8648700000000000276 ) ) ; +#99724 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99725 = LINE ( 'NONE', #11983, #7219 ) ; +#99726 = VECTOR ( 'NONE', #41423, 1000.000000000000000 ) ; +#99727 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99728 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99729 = LINE ( 'NONE', #100228, #71587 ) ; +#99730 = CARTESIAN_POINT ( 'NONE', ( -1.155438311688310016, -0.8844155844155849877, 0.8299999999999999600 ) ) ; +#99731 = AXIS2_PLACEMENT_3D ( 'NONE', #61352, #24047, #92431 ) ; +#99732 = ORIENTED_EDGE ( 'NONE', *, *, #33757, .F. ) ; +#99733 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.500000000000000000, 0.1829999999999999960 ) ) ; +#99734 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99735 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #5623, #59839, #6597, #12752 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#99736 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64010 ) ) ; +#99737 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #78710 ) ) ; +#99738 = SURFACE_STYLE_FILL_AREA ( #19753 ) ; +#99739 = ORIENTED_EDGE ( 'NONE', *, *, #91953, .T. ) ; +#99740 = FACE_OUTER_BOUND ( 'NONE', #86814, .T. ) ; +#99741 = EDGE_CURVE ( 'NONE', #93530, #38892, #15554, .T. ) ; +#99742 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99743 = PRESENTATION_STYLE_ASSIGNMENT (( #61088 ) ) ; +#99744 = LINE ( 'NONE', #100740, #73297 ) ; +#99745 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99746 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29047 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #71383, #41272, #87711 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99747 = ORIENTED_EDGE ( 'NONE', *, *, #96975, .F. ) ; +#99748 = PLANE ( 'NONE', #99369 ) ; +#99749 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #703, 'distance_accuracy_value', 'NONE'); +#99750 = LINE ( 'NONE', #23286, #45819 ) ; +#99751 = STYLED_ITEM ( 'NONE', ( #84387 ), #35627 ) ; +#99752 = EDGE_CURVE ( 'NONE', #77797, #75533, #39080, .T. ) ; +#99753 = ORIENTED_EDGE ( 'NONE', *, *, #16917, .T. ) ; +#99754 = ORIENTED_EDGE ( 'NONE', *, *, #58594, .F. ) ; +#99755 = EDGE_CURVE ( 'NONE', #70744, #28141, #23771, .T. ) ; +#99756 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86846 ), #33056 ) ; +#99757 = STYLED_ITEM ( 'NONE', ( #18035 ), #34896 ) ; +#99758 = CARTESIAN_POINT ( 'NONE', ( 10.00000000000000000, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#99759 = VERTEX_POINT ( 'NONE', #70714 ) ; +#99760 = CARTESIAN_POINT ( 'NONE', ( 0.5453366361084071023, -1.079472621882799910, 0.8299999999999999600 ) ) ; +#99761 = PRESENTATION_STYLE_ASSIGNMENT (( #62622 ) ) ; +#99762 = STYLED_ITEM ( 'NONE', ( #68509 ), #60201 ) ; +#99763 = SURFACE_STYLE_FILL_AREA ( #60610 ) ; +#99764 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99765 = CONTEXT_DEPENDENT_SHAPE_REPRESENTATION ( #52214, #17332 ) ; +#99766 = FILL_AREA_STYLE ('',( #14576 ) ) ; +#99767 = ORIENTED_EDGE ( 'NONE', *, *, #16396, .F. ) ; +#99768 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #94915 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #80511, #65173, #18687 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99769 = ORIENTED_EDGE ( 'NONE', *, *, #60939, .T. ) ; +#99770 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99771 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99772 = EDGE_CURVE ( 'NONE', #94313, #33091, #49787, .T. ) ; +#99773 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #51393, 'distance_accuracy_value', 'NONE'); +#99774 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99775 = FACE_OUTER_BOUND ( 'NONE', #29062, .T. ) ; +#99777 = CARTESIAN_POINT ( 'NONE', ( 4.105090999999999823, 8.286473000000000866, 0.8648700000000000276 ) ) ; +#99776 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99778 = EDGE_CURVE ( 'NONE', #55276, #90693, #43586, .T. ) ; +#99779 = SURFACE_SIDE_STYLE ('',( #68724 ) ) ; +#99780 = FILL_AREA_STYLE ('',( #30961 ) ) ; +#99781 = ORIENTED_EDGE ( 'NONE', *, *, #55257, .T. ) ; +#99782 = SURFACE_STYLE_USAGE ( .BOTH. , #53456 ) ; +#99783 = ORIENTED_EDGE ( 'NONE', *, *, #87616, .T. ) ; +#99784 = ORIENTED_EDGE ( 'NONE', *, *, #85827, .T. ) ; +#99785 = CARTESIAN_POINT ( 'NONE', ( 1.328303542420389949, -1.268071887441960088, 0.8299999999999999600 ) ) ; +#99786 = EDGE_CURVE ( 'NONE', #62758, #91365, #81443, .T. ) ; +#99787 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998224, -2.700000000000000622, 0.8299999999999999600 ) ) ; +#99788 = DIRECTION ( 'NONE', ( 1.000000000000000000, -1.084202172485500095E-15, 0.000000000000000000 ) ) ; +#99789 = EDGE_CURVE ( 'NONE', #94849, #62227, #17425, .T. ) ; +#99790 = AXIS2_PLACEMENT_3D ( 'NONE', #87235, #34161, #18783 ) ; +#99792 = ORIENTED_EDGE ( 'NONE', *, *, #93052, .T. ) ; +#99791 = FACE_OUTER_BOUND ( 'NONE', #9213, .T. ) ; +#99793 = CARTESIAN_POINT ( 'NONE', ( 5.724999999999999645, 0.2999999999999999889, 0.000000000000000000 ) ) ; +#99794 = ORIENTED_EDGE ( 'NONE', *, *, #41661, .F. ) ; +#99796 = FILL_AREA_STYLE_COLOUR ( '', #71380 ) ; +#99795 = LINE ( 'NONE', #77945, #41700 ) ; +#99797 = FILL_AREA_STYLE ('',( #46262 ) ) ; +#99799 = ORIENTED_EDGE ( 'NONE', *, *, #88704, .F. ) ; +#99798 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99800 = ORIENTED_EDGE ( 'NONE', *, *, #69446, .F. ) ; +#99801 = CYLINDRICAL_SURFACE ( 'NONE', #61709, 0.009999999999999998473 ) ; +#99803 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99802 = CARTESIAN_POINT ( 'NONE', ( 1.111329997291490068, -1.502675929081449979, 0.8299999999999999600 ) ) ; +#99804 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99805 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99806 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99807 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99808 = CARTESIAN_POINT ( 'NONE', ( -1.289336710954021248, -1.022720379215120934, 0.8099999999999712985 ) ) ; +#99809 = STYLED_ITEM ( 'NONE', ( #53954 ), #47129 ) ; +#99810 = STYLED_ITEM ( 'NONE', ( #2552 ), #25801 ) ; +#99811 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99812 = PRESENTATION_STYLE_ASSIGNMENT (( #76443 ) ) ; +#99813 = ORIENTED_EDGE ( 'NONE', *, *, #41626, .F. ) ; +#99814 = EDGE_CURVE ( 'NONE', #53312, #68882, #56956, .T. ) ; +#99815 = SURFACE_SIDE_STYLE ('',( #63180 ) ) ; +#99816 = ORIENTED_EDGE ( 'NONE', *, *, #28812, .F. ) ; +#99817 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #73755 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #79486, #39653, #40677 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99818 = FILL_AREA_STYLE_COLOUR ( '', #3293 ) ; +#99819 = CARTESIAN_POINT ( 'NONE', ( -0.01509916179266439923, -1.018845982455530041, 0.8299999999999999600 ) ) ; +#99820 = CARTESIAN_POINT ( 'NONE', ( 1.059875661710510064, -1.061634207873779934, 0.8299999999999999600 ) ) ; +#99821 = CYLINDRICAL_SURFACE ( 'NONE', #85569, 0.01902760257185397846 ) ; +#99822 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #42886 ) ) ; +#99823 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88510 ), #15130 ) ; +#99824 = FILL_AREA_STYLE ('',( #75459 ) ) ; +#99825 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#99826 = SURFACE_SIDE_STYLE ('',( #43315 ) ) ; +#99827 = EDGE_CURVE ( 'NONE', #89669, #66285, #11862, .T. ) ; +#99828 = ORIENTED_EDGE ( 'NONE', *, *, #46453, .F. ) ; +#99829 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#99831 = VECTOR ( 'NONE', #62619, 1000.000000000000000 ) ; +#99830 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99832 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #86921 ), #62439 ) ; +#99833 = VECTOR ( 'NONE', #54115, 1000.000000000000000 ) ; +#99834 = SURFACE_STYLE_FILL_AREA ( #93257 ) ; +#99835 = FILL_AREA_STYLE ('',( #53997 ) ) ; +#99836 = PRESENTATION_STYLE_ASSIGNMENT (( #52011 ) ) ; +#99837 = EDGE_CURVE ( 'NONE', #73476, #7753, #14849, .T. ) ; +#99839 = CARTESIAN_POINT ( 'NONE', ( 1.818850168448489901, -1.194792006717259936, 0.8100000000000000533 ) ) ; +#99838 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #96582 ), #5391 ) ; +#99840 = LINE ( 'NONE', #22870, #50743 ) ; +#99841 = AXIS2_PLACEMENT_3D ( 'NONE', #8096, #48532, #56706 ) ; +#99842 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99843 = CIRCLE ( 'NONE', #39617, 0.4459546481032609644 ) ; +#99844 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#99845 = LINE ( 'NONE', #86139, #25969 ) ; +#99846 = EDGE_CURVE ( 'NONE', #19897, #94036, #43098, .T. ) ; +#99847 = VECTOR ( 'NONE', #75071, 1000.000000000000000 ) ; +#99848 = SURFACE_STYLE_FILL_AREA ( #13114 ) ; +#99849 = VECTOR ( 'NONE', #90668, 1000.000000000000000 ) ; +#99850 = SURFACE_STYLE_FILL_AREA ( #44809 ) ; +#99851 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9876 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #19283, #33634, #42783 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99852 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99853 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99854 = CARTESIAN_POINT ( 'NONE', ( -0.9424568159081126995, -1.019697217944794954, 0.8099999999999734079 ) ) ; +#99855 = ORIENTED_EDGE ( 'NONE', *, *, #89831, .F. ) ; +#99856 = DIRECTION ( 'NONE', ( -0.7071067834590476497, -0.7071067789140474957, 0.000000000000000000 ) ) ; +#99857 = SURFACE_STYLE_FILL_AREA ( #6479 ) ; +#99858 = CARTESIAN_POINT ( 'NONE', ( 1.571641772371880075, -1.354501511147599979, 0.8299999999999987388 ) ) ; +#99859 = PRESENTATION_STYLE_ASSIGNMENT (( #905 ) ) ; +#99860 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99861 = EDGE_CURVE ( 'NONE', #87419, #2486, #73749, .T. ) ; +#99862 = EDGE_CURVE ( 'NONE', #11817, #80711, #35478, .T. ) ; +#99863 = LINE ( 'NONE', #16690, #5878 ) ; +#99864 = VERTEX_POINT ( 'NONE', #18071 ) ; +#99865 = AXIS2_PLACEMENT_3D ( 'NONE', #19169, #13318, #68998 ) ; +#99866 = FILL_AREA_STYLE ('',( #60706 ) ) ; +#99867 = SURFACE_SIDE_STYLE ('',( #84166 ) ) ; +#99868 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99869 = CARTESIAN_POINT ( 'NONE', ( 15.40000000000000036, 15.40000000000000036, 0.03429000000000000103 ) ) ; +#99870 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99871 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#99872 = EDGE_CURVE ( 'NONE', #49054, #741, #16144, .T. ) ; +#99873 = CYLINDRICAL_SURFACE ( 'NONE', #52779, 0.01000000000000002623 ) ; +#99874 = ORIENTED_EDGE ( 'NONE', *, *, #18868, .T. ) ; +#99875 = ORIENTED_EDGE ( 'NONE', *, *, #77424, .T. ) ; +#99876 = EDGE_CURVE ( 'NONE', #23560, #74996, #58474, .T. ) ; +#99877 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #31491 ), #13479 ) ; +#99878 = EDGE_LOOP ( 'NONE', ( #24037, #78310, #87982, #8283 ) ) ; +#99879 = SURFACE_STYLE_FILL_AREA ( #22917 ) ; +#99880 = SURFACE_STYLE_FILL_AREA ( #53550 ) ; +#99881 = AXIS2_PLACEMENT_3D ( 'NONE', #43339, #66817, #59213 ) ; +#99882 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#99883 = SURFACE_STYLE_FILL_AREA ( #926 ) ; +#99884 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99885 = APPLICATION_PROTOCOL_DEFINITION ( 'draft international standard', 'automotive_design', 1998, #58646 ) ; +#99886 = PRESENTATION_STYLE_ASSIGNMENT (( #78041 ) ) ; +#99887 = FACE_OUTER_BOUND ( 'NONE', #7845, .T. ) ; +#99889 = ORIENTED_EDGE ( 'NONE', *, *, #69827, .T. ) ; +#99888 = VERTEX_POINT ( 'NONE', #90060 ) ; +#99890 = VECTOR ( 'NONE', #60903, 1000.000000000000000 ) ; +#99891 = ORIENTED_EDGE ( 'NONE', *, *, #68399, .T. ) ; +#99892 = SURFACE_SIDE_STYLE ('',( #60252 ) ) ; +#99893 = EDGE_CURVE ( 'NONE', #32802, #76548, #74756, .T. ) ; +#99895 = CIRCLE ( 'NONE', #67357, 0.1000000000000000056 ) ; +#99894 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #90411, 'distance_accuracy_value', 'NONE'); +#99897 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99896 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99898 = ORIENTED_EDGE ( 'NONE', *, *, #12282, .F. ) ; +#99899 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8298 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #15960, #77249, #70090 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99900 = ORIENTED_EDGE ( 'NONE', *, *, #25232, .F. ) ; +#99901 = FILL_AREA_STYLE_COLOUR ( '', #95527 ) ; +#99902 = ADVANCED_FACE ( 'NONE', ( #88555 ), #51282, .F. ) ; +#99903 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #88657 ), #87067 ) ; +#99904 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #63302 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68408, #67892, #99472 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99905 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #77197 ) ) ; +#99906 = CARTESIAN_POINT ( 'NONE', ( -0.3000000000000000444, -0.008431457505076164760, -0.1458578643762690474 ) ) ; +#99908 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.2700000000000000178, -0.1350000000000000089 ) ) ; +#99907 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99909 = ORIENTED_EDGE ( 'NONE', *, *, #4304, .F. ) ; +#99910 = CARTESIAN_POINT ( 'NONE', ( -0.5167674196284709476, -0.9767818844061101347, 0.8100000000000000533 ) ) ; +#99911 = VECTOR ( 'NONE', #90773, 1000.000000000000000 ) ; +#99912 = EDGE_LOOP ( 'NONE', ( #84299, #22177, #19671, #82353 ) ) ; +#99913 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64192 ) ) ; +#99914 = VERTEX_POINT ( 'NONE', #13383 ) ; +#99915 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99916 = EDGE_CURVE ( 'NONE', #20037, #68343, #75743, .T. ) ; +#99917 = EDGE_CURVE ( 'NONE', #12927, #37298, #6235, .T. ) ; +#99918 = VECTOR ( 'NONE', #79853, 999.9999999999998863 ) ; +#99919 = ORIENTED_EDGE ( 'NONE', *, *, #6208, .T. ) ; +#99920 = VECTOR ( 'NONE', #59944, 1000.000000000000114 ) ; +#99921 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99922 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #44552 ), #56052 ) ; +#99923 = SURFACE_STYLE_USAGE ( .BOTH. , #68862 ) ; +#99924 = EDGE_LOOP ( 'NONE', ( #51249, #18125, #23066, #20740 ) ) ; +#99925 = LINE ( 'NONE', #5569, #63177 ) ; +#99926 = LINE ( 'NONE', #69885, #98235 ) ; +#99927 = EDGE_LOOP ( 'NONE', ( #59019, #64976, #48438, #21025, #79159, #46632 ) ) ; +#99928 = EDGE_LOOP ( 'NONE', ( #1031, #83328, #47412, #81799 ) ) ; +#99929 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99930 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -2.500000000000000000, -0.02000000000003633593 ) ) ; +#99931 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #8212 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #33338, #96078, #63971 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#99932 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#99933 = CARTESIAN_POINT ( 'NONE', ( 0.1000000000000000056, -3.499999999999980016, 0.1829999999999999960 ) ) ; +#99934 = FACE_OUTER_BOUND ( 'NONE', #47902, .T. ) ; +#99935 = CARTESIAN_POINT ( 'NONE', ( 1.354949560415620091, -1.296162859166370307, 0.8299999999999997380 ) ) ; +#99936 = LINE ( 'NONE', #29598, #98492 ) ; +#99937 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#99938 = ORIENTED_EDGE ( 'NONE', *, *, #68602, .T. ) ; +#99939 = EDGE_CURVE ( 'NONE', #75798, #16963, #52292, .T. ) ; +#99940 = ORIENTED_EDGE ( 'NONE', *, *, #47734, .T. ) ; +#99941 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99942 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 14.25000000000000000, 0.000000000000000000 ) ) ; +#99943 = LINE ( 'NONE', #60296, #23723 ) ; +#99944 = CARTESIAN_POINT ( 'NONE', ( 8.121456999999999482, 10.67649499999999918, 0.8991599999999999593 ) ) ; +#99945 = VECTOR ( 'NONE', #33348, 1000.000000000000000 ) ; +#99946 = SURFACE_STYLE_FILL_AREA ( #36787 ) ; +#99947 = CARTESIAN_POINT ( 'NONE', ( 1.776971753240009999, -0.9939892240680031632, 0.8299999999999999600 ) ) ; +#99948 = CARTESIAN_POINT ( 'NONE', ( 1.708426850688339993, -1.163903542943879987, 0.8299999999999999600 ) ) ; +#99950 = EDGE_CURVE ( 'NONE', #60955, #72878, #53769, .T. ) ; +#99949 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#99951 = CARTESIAN_POINT ( 'NONE', ( -1.000000000000000000, 0.1200000000000000094, 0.6199999999999999956 ) ) ; +#99952 = FILL_AREA_STYLE_COLOUR ( '', #68744 ) ; +#99953 = CARTESIAN_POINT ( 'NONE', ( 4.230000000000000426, 1.399999999999999911, -11.57000000000000028 ) ) ; +#99954 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, -3.520000000000000018, -0.02000000000000000042 ) ) ; +#99955 = LINE ( 'NONE', #22989, #1667 ) ; +#99956 = FILL_AREA_STYLE ('',( #58929 ) ) ; +#99957 = EDGE_CURVE ( 'NONE', #28450, #62347, #82028, .T. ) ; +#99958 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99959 = VECTOR ( 'NONE', #61361, 1000.000000000000000 ) ; +#99960 = CARTESIAN_POINT ( 'NONE', ( 12.68125900000000073, 12.04378999999999955, 0.8991599999999999593 ) ) ; +#99961 = FILL_AREA_STYLE ('',( #61804 ) ) ; +#99964 = DIRECTION ( 'NONE', ( -0.7071067811865493491, 0.7071067811865455743, 0.000000000000000000 ) ) ; +#99963 = PLANE ( 'NONE', #39126 ) ; +#99962 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#99965 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99966 = ADVANCED_FACE ( 'NONE', ( #5254 ), #45073, .T. ) ; +#99967 = AXIS2_PLACEMENT_3D ( 'NONE', #58446, #81899, #90541 ) ; +#99969 = VERTEX_POINT ( 'NONE', #28293 ) ; +#99968 = STYLED_ITEM ( 'NONE', ( #91176 ), #21453 ) ; +#99970 = CARTESIAN_POINT ( 'NONE', ( -1.002767861914739989, -1.390055052842650074, 0.8100000000000000533 ) ) ; +#99971 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #74351, 'distance_accuracy_value', 'NONE'); +#99972 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #72712, 'distance_accuracy_value', 'NONE'); +#99973 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#99974 = SURFACE_STYLE_FILL_AREA ( #91428 ) ; +#99975 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#99977 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59328 ), #36492 ) ; +#99976 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #16907 ) ) ; +#99978 = CARTESIAN_POINT ( 'NONE', ( 4.549999999999999822, 1.149999999999999911, 0.000000000000000000 ) ) ; +#99979 = VECTOR ( 'NONE', #26509, 1000.000000000000000 ) ; +#99980 = LINE ( 'NONE', #78132, #43388 ) ; +#99981 = SURFACE_SIDE_STYLE ('',( #76605 ) ) ; +#99982 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#99983 = LINE ( 'NONE', #61330, #59552 ) ; +#99984 = EDGE_CURVE ( 'NONE', #81104, #4549, #14413, .T. ) ; +#99985 = EDGE_CURVE ( 'NONE', #27071, #32909, #70973, .T. ) ; +#99986 = VECTOR ( 'NONE', #63104, 1000.000000000000000 ) ; +#99987 = CARTESIAN_POINT ( 'NONE', ( 10.21449324974999939, 6.264147750250000257, 0.8648700000000000276 ) ) ; +#99988 = VERTEX_POINT ( 'NONE', #20607 ) ; +#99989 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 8.300000000000000711, 0.03429000000000000103 ) ) ; +#99990 = ORIENTED_EDGE ( 'NONE', *, *, #25393, .F. ) ; +#99991 = FACE_OUTER_BOUND ( 'NONE', #44623, .T. ) ; +#99992 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #26557, 'distance_accuracy_value', 'NONE'); +#99993 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #19490, 'distance_accuracy_value', 'NONE'); +#99994 = CARTESIAN_POINT ( 'NONE', ( 6.261766000000000609, 3.004386000000000223, 0.8648700000000000276 ) ) ; +#99995 = CARTESIAN_POINT ( 'NONE', ( -0.1522818774044870371, -0.9679977428869791511, 0.8299999999999999600 ) ) ; +#99996 = STYLED_ITEM ( 'NONE', ( #98213 ), #11819 ) ; +#99997 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#99998 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#99999 = ORIENTED_EDGE ( 'NONE', *, *, #18873, .F. ) ; +#100000 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100001 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.8299999999999999600 ) ) ; +#100002 = VERTEX_POINT ( 'NONE', #67561 ) ; +#100003 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#100004 = EDGE_CURVE ( 'NONE', #35754, #11562, #59968, .T. ) ; +#100005 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100006 = DIRECTION ( 'NONE', ( -1.274473528905959955E-45, 1.000000000000000000, -1.498136433501504447E-75 ) ) ; +#100007 = VERTEX_POINT ( 'NONE', #44574 ) ; +#100008 = EDGE_CURVE ( 'NONE', #12514, #79176, #32105, .T. ) ; +#100009 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #59431 ), #82223 ) ; +#100010 = FILL_AREA_STYLE_COLOUR ( '', #60438 ) ; +#100011 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100013 = ORIENTED_EDGE ( 'NONE', *, *, #28372, .F. ) ; +#100012 = ORIENTED_EDGE ( 'NONE', *, *, #63651, .T. ) ; +#100014 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100015 = FILL_AREA_STYLE_COLOUR ( '', #70841 ) ; +#100016 = VERTEX_POINT ( 'NONE', #30259 ) ; +#100017 = LINE ( 'NONE', #76645, #31350 ) ; +#100018 = VECTOR ( 'NONE', #24066, 1000.000000000000000 ) ; +#100019 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#100020 = ORIENTED_EDGE ( 'NONE', *, *, #10382, .T. ) ; +#100021 = ORIENTED_EDGE ( 'NONE', *, *, #70239, .F. ) ; +#100022 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100023 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#100024 = CARTESIAN_POINT ( 'NONE', ( -0.5298487572449830374, -1.185132602208770036, 0.8299999999999999600 ) ) ; +#100026 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100025 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100027 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100028 = ORIENTED_EDGE ( 'NONE', *, *, #374, .F. ) ; +#100029 = ORIENTED_EDGE ( 'NONE', *, *, #14524, .T. ) ; +#100030 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #43078 ) ) ; +#100031 = VECTOR ( 'NONE', #70351, 1000.000000000000000 ) ; +#100032 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#100033 = ORIENTED_EDGE ( 'NONE', *, *, #20852, .F. ) ; +#100034 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999994005, 3.149999999999990585, 1.048695503451051965E-76 ) ) ; +#100035 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #81939 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #38538, #6320, #37051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100036 = STYLED_ITEM ( 'NONE', ( #90831 ), #25822 ) ; +#100037 = EDGE_CURVE ( 'NONE', #84179, #72485, #13905, .T. ) ; +#100039 = VERTEX_POINT ( 'NONE', #69568 ) ; +#100038 = FILL_AREA_STYLE_COLOUR ( '', #91710 ) ; +#100040 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #81469, #42636, #34999, #32964 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100041 = LINE ( 'NONE', #47542, #71882 ) ; +#100042 = VECTOR ( 'NONE', #87376, 1000.000000000000000 ) ; +#100044 = SURFACE_STYLE_USAGE ( .BOTH. , #99557 ) ; +#100043 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100045 = SURFACE_STYLE_FILL_AREA ( #52702 ) ; +#100046 = DIRECTION ( 'NONE', ( 0.7071067811865472397, -0.7071067811865479058, 0.000000000000000000 ) ) ; +#100047 = ORIENTED_EDGE ( 'NONE', *, *, #48227, .T. ) ; +#100048 = EDGE_CURVE ( 'NONE', #12557, #72982, #1682, .T. ) ; +#100050 = CARTESIAN_POINT ( 'NONE', ( 5.802147000000000610, 9.983529000000000764, 0.8648700000000000276 ) ) ; +#100049 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #3959 ), #59477 ) ; +#100051 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100052 = ORIENTED_EDGE ( 'NONE', *, *, #94433, .F. ) ; +#100053 = CARTESIAN_POINT ( 'NONE', ( -0.05684101355748980011, -0.9053603395923379704, 0.8299999999999988498 ) ) ; +#100054 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7804 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #83880, #90024, #12349 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100055 = SURFACE_STYLE_FILL_AREA ( #61889 ) ; +#100056 = ORIENTED_EDGE ( 'NONE', *, *, #12382, .T. ) ; +#100057 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #7569 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62480, #8250, #38473 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100059 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 3.500000000000000000, 0.1829999999999540328 ) ) ; +#100058 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.399999999999999911, -0.2000000000000000111 ) ) ; +#100060 = CARTESIAN_POINT ( 'NONE', ( -0.9116883116883119920, -1.337215909090909927, 0.8099999999998959144 ) ) ; +#100061 = EDGE_CURVE ( 'NONE', #80171, #49262, #71106, .T. ) ; +#100062 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100063 = ORIENTED_EDGE ( 'NONE', *, *, #92396, .T. ) ; +#100064 = LINE ( 'NONE', #23093, #37037 ) ; +#100065 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100066 = VECTOR ( 'NONE', #99076, 1000.000000000000000 ) ; +#100067 = DIRECTION ( 'NONE', ( -0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#100068 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #33379 ) ) ; +#100070 = CARTESIAN_POINT ( 'NONE', ( 1.585655134885600059, -1.389169665048220148, 0.8100000000000000533 ) ) ; +#100069 = CARTESIAN_POINT ( 'NONE', ( 3.099999999999969891, -0.2500000000000000000, -0.02000000000000000042 ) ) ; +#100071 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100072 = FILL_AREA_STYLE_COLOUR ( '', #76067 ) ; +#100073 = ADVANCED_FACE ( 'NONE', ( #138 ), #20477, .F. ) ; +#100074 = VECTOR ( 'NONE', #22391, 1000.000000000000000 ) ; +#100075 = CARTESIAN_POINT ( 'NONE', ( 2.973719000000000001, 7.155103000000000435, 0.8991599999999999593 ) ) ; +#100076 = VERTEX_POINT ( 'NONE', #62465 ) ; +#100077 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#100078 = VERTEX_POINT ( 'NONE', #87430 ) ; +#100079 = FILL_AREA_STYLE ('',( #37916 ) ) ; +#100080 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #80049 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16149, #77445, #85616 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100081 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100082 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100083 = EDGE_CURVE ( 'NONE', #51509, #77277, #63480, .T. ) ; +#100084 = FACE_OUTER_BOUND ( 'NONE', #99399, .T. ) ; +#100085 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #26824 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #10590, #57705, #26041 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100086 = CIRCLE ( 'NONE', #77380, 0.09999999999999939493 ) ; +#100087 = EDGE_CURVE ( 'NONE', #47598, #23664, #69596, .T. ) ; +#100088 = ORIENTED_EDGE ( 'NONE', *, *, #57796, .T. ) ; +#100089 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100090 = CARTESIAN_POINT ( 'NONE', ( 13.79999999999999893, 1.600000000000000089, 0.000000000000000000 ) ) ; +#100091 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #87178 ) ) ; +#100092 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#100093 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100094 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 4.549999999999999822, 0.03429000000000000103 ) ) ; +#100095 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #92038 ), #64374 ) ; +#100096 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #43149 ), #44728 ) ; +#100097 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100099 = EDGE_CURVE ( 'NONE', #20063, #12510, #8859, .T. ) ; +#100098 = B_SPLINE_SURFACE_WITH_KNOTS ( 'NONE', 3, 1, ( + ( #80159, #3548 ), + ( #87793, #18318 ), + ( #3030, #64813 ), + ( #49508, #27541 ), + ( #10083, #58200 ), + ( #95924, #34207 ), + ( #26531, #26035 ), + ( #33174, #80660 ), + ( #57187, #12117 ), + ( #66328, #18834 ), + ( #72985, #10585 ), + ( #27039, #19345 ), + ( #64309, #51030 ), + ( #74500, #58699 ), + ( #50538, #35209 ), + ( #95419, #11605 ), + ( #73987, #42848 ), + ( #4033, #25529 ), + ( #45806, #21354 ) ), + .UNSPECIFIED., .F., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 2, 2 ), + ( 0.000000000000000000, 0.07232018030895230598, 0.1403020240650759975, 0.2056949503128689960, 0.2680970257553140224, 0.3283846161759810256, 0.3866606845022029781, 0.4439167269204030153, 0.5001855221813320540, 0.5567435589820139974, 0.6139463218703099523, 0.6733207137601100456, 0.7343865386942719509, 0.7975760200560489954, 0.8623103139506780312, 0.9300018147880010355, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100100 = PLANE ( 'NONE', #73781 ) ; +#100101 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #60181, 'distance_accuracy_value', 'NONE'); +#100102 = EDGE_CURVE ( 'NONE', #64466, #62000, #48136, .T. ) ; +#100103 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100104 = VERTEX_POINT ( 'NONE', #73628 ) ; +#100105 = LINE ( 'NONE', #57314, #30170 ) ; +#100106 = VERTEX_POINT ( 'NONE', #81318 ) ; +#100107 = CARTESIAN_POINT ( 'NONE', ( 1.699999999999991962, 3.500000000000000444, -9.095983544939292593E-90 ) ) ; +#100108 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95196, 'distance_accuracy_value', 'NONE'); +#100109 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #56046, 'distance_accuracy_value', 'NONE'); +#100110 = ADVANCED_FACE ( 'NONE', ( #11735 ), #26176, .T. ) ; +#100111 = EDGE_CURVE ( 'NONE', #25185, #43280, #64745, .T. ) ; +#100112 = CARTESIAN_POINT ( 'NONE', ( 1.121762993838200106, -0.9661431204389000493, 0.8100000000000000533 ) ) ; +#100113 = LINE ( 'NONE', #46061, #91903 ) ; +#100114 = CARTESIAN_POINT ( 'NONE', ( -0.007792207792208251035, -1.062784090909089985, 0.8100000000000610045 ) ) ; +#100115 = DIRECTION ( 'NONE', ( 9.922965125553800473E-95, 2.143355994988570127E-63, 1.000000000000000000 ) ) ; +#100116 = VECTOR ( 'NONE', #93146, 1000.000000000000000 ) ; +#100117 = CARTESIAN_POINT ( 'NONE', ( 0.8499999999999999778, 1.474514954580256140E-18, -0.8499999999999999778 ) ) ; +#100118 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999990141, 1.500000000000000000, -0.02000000000000630093 ) ) ; +#100119 = PRESENTATION_STYLE_ASSIGNMENT (( #31283 ) ) ; +#100120 = DIRECTION ( 'NONE', ( -0.7071067806865475314, -0.7071067816865476141, 0.000000000000000000 ) ) ; +#100121 = ORIENTED_EDGE ( 'NONE', *, *, #74909, .F. ) ; +#100122 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100123 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100124 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #93727, 'distance_accuracy_value', 'NONE'); +#100125 = EDGE_CURVE ( 'NONE', #97527, #449, #97571, .T. ) ; +#100126 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100127 = ORIENTED_EDGE ( 'NONE', *, *, #30129, .F. ) ; +#100128 = CARTESIAN_POINT ( 'NONE', ( 2.299999999999999822, -3.149999999999970157, 0.000000000000000000 ) ) ; +#100129 = EDGE_CURVE ( 'NONE', #44212, #40649, #34851, .T. ) ; +#100130 = AXIS2_PLACEMENT_3D ( 'NONE', #35751, #5041, #89840 ) ; +#100131 = CARTESIAN_POINT ( 'NONE', ( 4.493902000000000285, 13.54677200000000070, 0.8648700000000000276 ) ) ; +#100132 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999989786, 2.100000000000000089, -0.02000000000000000042 ) ) ; +#100133 = PRESENTATION_STYLE_ASSIGNMENT (( #76254 ) ) ; +#100134 = PLANE ( 'NONE', #52813 ) ; +#100135 = VERTEX_POINT ( 'NONE', #25661 ) ; +#100136 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100137 = LINE ( 'NONE', #31306, #62026 ) ; +#100138 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1537, 'distance_accuracy_value', 'NONE'); +#100139 = PLANE ( 'NONE', #56003 ) ; +#100140 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #75770 ), #17082 ) ; +#100141 =( BOUNDED_SURFACE ( ) B_SPLINE_SURFACE ( 3, 3, ( + ( #74846, #19720, #66672, #4875 ), + ( #5355, #36569, #89672, #97296 ), + ( #97775, #36064, #98249, #67176 ), + ( #89170, #27911, #59581, #90671 ) ), + .UNSPECIFIED., .F., .F., .F. ) + B_SPLINE_SURFACE_WITH_KNOTS ( ( 4, 4 ), + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) + GEOMETRIC_REPRESENTATION_ITEM ( ) RATIONAL_B_SPLINE_SURFACE ( ( + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000), + ( 0.8047378541243662697, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243662697), + ( 0.8047378541243662697, 0.6476030138606883035, 0.6476030138606883035, 0.8047378541243662697), + ( 1.000000000000000000, 0.8047378541243643824, 0.8047378541243643824, 1.000000000000000000) ) ) + REPRESENTATION_ITEM ( '' ) SURFACE ( ) ); +#100142 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100143 = ORIENTED_EDGE ( 'NONE', *, *, #51320, .T. ) ; +#100144 = FILL_AREA_STYLE_COLOUR ( '', #39195 ) ; +#100145 = VECTOR ( 'NONE', #27321, 1000.000000000000000 ) ; +#100146 = DIRECTION ( 'NONE', ( 0.7071067811865474617, -0.7071067811865474617, -0.000000000000000000 ) ) ; +#100147 = SURFACE_STYLE_USAGE ( .BOTH. , #47655 ) ; +#100148 = VERTEX_POINT ( 'NONE', #73129 ) ; +#100149 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #69821 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #52710, #61401, #60399 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100150 = ORIENTED_EDGE ( 'NONE', *, *, #85977, .F. ) ; +#100151 = ORIENTED_EDGE ( 'NONE', *, *, #8968, .F. ) ; +#100153 = ORIENTED_EDGE ( 'NONE', *, *, #11789, .T. ) ; +#100152 = LINE ( 'NONE', #71149, #13373 ) ; +#100154 = FILL_AREA_STYLE_COLOUR ( '', #26391 ) ; +#100155 = FILL_AREA_STYLE_COLOUR ( '', #96597 ) ; +#100156 = CARTESIAN_POINT ( 'NONE', ( 0.7053571428571427937, 0.7099999999999999645, 0.5000000000000000000 ) ) ; +#100157 = SURFACE_STYLE_USAGE ( .BOTH. , #45114 ) ; +#100158 = ORIENTED_EDGE ( 'NONE', *, *, #71276, .T. ) ; +#100160 = ADVANCED_FACE ( 'NONE', ( #89936 ), #50671, .T. ) ; +#100159 = SURFACE_STYLE_USAGE ( .BOTH. , #15993 ) ; +#100161 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100162 = FACE_OUTER_BOUND ( 'NONE', #27002, .T. ) ; +#100163 = VERTEX_POINT ( 'NONE', #50178 ) ; +#100164 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #61806, #86263, #94412, #92873 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100165 = AXIS2_PLACEMENT_3D ( 'NONE', #16712, #25951, #57100 ) ; +#100166 = CARTESIAN_POINT ( 'NONE', ( 1.441319620083689967, -1.344945484192040075, 0.8100000000000000533 ) ) ; +#100167 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #61181 ), #62855 ) ; +#100168 = STYLED_ITEM ( 'NONE', ( #66553 ), #88960 ) ; +#100169 = SURFACE_SIDE_STYLE ('',( #45122 ) ) ; +#100170 = CARTESIAN_POINT ( 'NONE', ( 6.128879999999999661, 12.37581999999999915, 0.8991599999999999593 ) ) ; +#100171 = ORIENTED_EDGE ( 'NONE', *, *, #9980, .F. ) ; +#100173 = FILL_AREA_STYLE ('',( #75800 ) ) ; +#100172 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #5713 ) ) ; +#100174 = AXIS2_PLACEMENT_3D ( 'NONE', #64100, #70220, #78906 ) ; +#100175 = ORIENTED_EDGE ( 'NONE', *, *, #693, .F. ) ; +#100176 = STYLED_ITEM ( 'NONE', ( #71040 ), #26941 ) ; +#100177 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100178 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10471 ), #92121 ) ; +#100179 = PLANE ( 'NONE', #84856 ) ; +#100180 = FILL_AREA_STYLE_COLOUR ( '', #45082 ) ; +#100181 = ORIENTED_EDGE ( 'NONE', *, *, #38454, .F. ) ; +#100182 = CARTESIAN_POINT ( 'NONE', ( -2.250000000000000444, 3.100000000000000533, 0.000000000000000000 ) ) ; +#100183 = ORIENTED_EDGE ( 'NONE', *, *, #18825, .T. ) ; +#100184 = VECTOR ( 'NONE', #82178, 1000.000000000000000 ) ; +#100185 = FILL_AREA_STYLE_COLOUR ( '', #86557 ) ; +#100186 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100187 = EDGE_CURVE ( 'NONE', #16589, #90226, #4176, .T. ) ; +#100188 = AXIS2_PLACEMENT_3D ( 'NONE', #54848, #85960, #48695 ) ; +#100189 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100190 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #89178, 'distance_accuracy_value', 'NONE'); +#100191 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100192 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, -0.000000000000000000 ) ) ; +#100193 = DIRECTION ( 'NONE', ( 1.000000000000000000, -6.168691825067458519E-64, 4.551691174664149710E-48 ) ) ; +#100194 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100195 = CARTESIAN_POINT ( 'NONE', ( 8.793208750250085970, 9.241067249749910673, 0.8648700000000000276 ) ) ; +#100196 = VERTEX_POINT ( 'NONE', #10225 ) ; +#100197 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100198 = FILL_AREA_STYLE_COLOUR ( '', #46386 ) ; +#100200 = PLANE ( 'NONE', #65626 ) ; +#100199 = CARTESIAN_POINT ( 'NONE', ( 4.379999999999999893, 1.593649167310369874, -11.91999999999999993 ) ) ; +#100201 = CYLINDRICAL_SURFACE ( 'NONE', #63442, 0.05000000000000012768 ) ; +#100202 = PLANE ( 'NONE', #48545 ) ; +#100203 = PRESENTATION_STYLE_ASSIGNMENT (( #94135 ) ) ; +#100204 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100205 = CARTESIAN_POINT ( 'NONE', ( -2.149999999999999911, 3.100000000000000533, 0.000000000000000000 ) ) ; +#100206 = CARTESIAN_POINT ( 'NONE', ( 11.35000000000000142, 0.2500000000000000000, 0.03429000000000000103 ) ) ; +#100207 = VERTEX_POINT ( 'NONE', #52657 ) ; +#100208 = FILL_AREA_STYLE ('',( #53872 ) ) ; +#100209 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100210 = CARTESIAN_POINT ( 'NONE', ( -0.08876197264234840512, -1.443664018207750033, 0.8299999999999999600 ) ) ; +#100211 = STYLED_ITEM ( 'NONE', ( #79819 ), #68351 ) ; +#100212 = DIRECTION ( 'NONE', ( -6.141358241030730393E-32, -0.000000000000000000, 1.000000000000000000 ) ) ; +#100213 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #99592, 'distance_accuracy_value', 'NONE'); +#100214 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100215 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100216 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100217 = FILL_AREA_STYLE ('',( #77864 ) ) ; +#100218 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 1.099999999999999867, 0.1829999999999829818 ) ) ; +#100219 = CARTESIAN_POINT ( 'NONE', ( -3.520000000000000018, -1.699999999999999956, 0.1829999999999540050 ) ) ; +#100220 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #61388, 'distance_accuracy_value', 'NONE'); +#100222 = EDGE_CURVE ( 'NONE', #61494, #40536, #83304, .T. ) ; +#100221 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#100223 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999980549, 0.5500000000000000444, 0.000000000000000000 ) ) ; +#100224 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #20009, 'distance_accuracy_value', 'NONE'); +#100225 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100226 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #22067 ), #77525 ) ; +#100227 = STYLED_ITEM ( 'NONE', ( #54247 ), #54361 ) ; +#100228 = CARTESIAN_POINT ( 'NONE', ( 6.827450999999999937, 10.08959499999999920, 0.8648700000000000276 ) ) ; +#100229 = FILL_AREA_STYLE ('',( #53894 ) ) ; +#100230 = PRESENTATION_STYLE_ASSIGNMENT (( #30373 ) ) ; +#100231 = FACE_OUTER_BOUND ( 'NONE', #70376, .T. ) ; +#100232 = VERTEX_POINT ( 'NONE', #59355 ) ; +#100233 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -0.02000000000000000042 ) ) ; +#100234 = VECTOR ( 'NONE', #88588, 1000.000000000000000 ) ; +#100235 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #23020, 'distance_accuracy_value', 'NONE'); +#100237 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100236 = VECTOR ( 'NONE', #36315, 1000.000000000000000 ) ; +#100238 = CARTESIAN_POINT ( 'NONE', ( 5.264745499500000037, 5.557041499500000370, 0.8991599999999999593 ) ) ; +#100239 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100240 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #9029 ) ) ; +#100241 = ORIENTED_EDGE ( 'NONE', *, *, #35180, .F. ) ; +#100242 = FACE_OUTER_BOUND ( 'NONE', #20011, .T. ) ; +#100243 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #33564 ), #90607 ) ; +#100244 = EDGE_CURVE ( 'NONE', #2733, #55045, #93869, .T. ) ; +#100245 = CARTESIAN_POINT ( 'NONE', ( 7.099999999999999645, 14.25000000000000000, 0.000000000000000000 ) ) ; +#100246 = SURFACE_STYLE_USAGE ( .BOTH. , #29907 ) ; +#100247 = SURFACE_STYLE_FILL_AREA ( #39095 ) ; +#100248 = ORIENTED_EDGE ( 'NONE', *, *, #21631, .F. ) ; +#100249 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100250 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #95015, 'distance_accuracy_value', 'NONE'); +#100251 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #92194 ) ) ; +#100252 = CARTESIAN_POINT ( 'NONE', ( -0.07646240217796579364, -1.441250752426249893, 0.8300000000000006262 ) ) ; +#100253 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100254 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100255 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#100256 = ORIENTED_EDGE ( 'NONE', *, *, #17852, .T. ) ; +#100257 = EDGE_LOOP ( 'NONE', ( #48163, #99539, #78157, #18950 ) ) ; +#100258 = VECTOR ( 'NONE', #44504, 1000.000000000000000 ) ; +#100259 = STYLED_ITEM ( 'NONE', ( #37448 ), #99023 ) ; +#100260 = PLANE ( 'NONE', #39410 ) ; +#100261 = ORIENTED_EDGE ( 'NONE', *, *, #76870, .F. ) ; +#100262 = FILL_AREA_STYLE ('',( #54955 ) ) ; +#100263 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100264 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100265 = SURFACE_STYLE_FILL_AREA ( #70237 ) ; +#100266 = VECTOR ( 'NONE', #48599, 1000.000000000000000 ) ; +#100267 = VECTOR ( 'NONE', #5059, 1000.000000000000000 ) ; +#100268 = CARTESIAN_POINT ( 'NONE', ( 3.520000000000000018, -4.956352788505160155E-18, 0.000000000000000000 ) ) ; +#100269 = EDGE_LOOP ( 'NONE', ( #16614, #99828, #14542, #48529 ) ) ; +#100270 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #64182 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #89736, #81108, #12051 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100271 = ORIENTED_EDGE ( 'NONE', *, *, #81676, .F. ) ; +#100272 = SURFACE_SIDE_STYLE ('',( #63995 ) ) ; +#100273 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100274 = CARTESIAN_POINT ( 'NONE', ( 3.096176609181506599E-33, 0.2999999999999999334, -1.665334536937739679E-17 ) ) ; +#100275 = EDGE_CURVE ( 'NONE', #45738, #13162, #13775, .T. ) ; +#100276 = EDGE_LOOP ( 'NONE', ( #70551, #6920, #68128, #63217 ) ) ; +#100277 = LINE ( 'NONE', #61628, #48114 ) ; +#100278 = FILL_AREA_STYLE_COLOUR ( '', #32675 ) ; +#100279 = SURFACE_SIDE_STYLE ('',( #69206 ) ) ; +#100280 = VERTEX_POINT ( 'NONE', #68448 ) ; +#100282 = PRESENTATION_STYLE_ASSIGNMENT (( #6887 ) ) ; +#100281 = CARTESIAN_POINT ( 'NONE', ( -3.100000000000000533, 2.549999999999999822, -0.02000000000000000042 ) ) ; +#100283 = EDGE_LOOP ( 'NONE', ( #88479, #79666, #40598, #10513 ) ) ; +#100284 = ORIENTED_EDGE ( 'NONE', *, *, #21584, .F. ) ; +#100285 = PLANE ( 'NONE', #41290 ) ; +#100287 = SURFACE_SIDE_STYLE ('',( #67742 ) ) ; +#100286 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666627084, -2.500000000000000000, 0.000000000000000000 ) ) ; +#100288 = VECTOR ( 'NONE', #23344, 1000.000000000000000 ) ; +#100289 = FILL_AREA_STYLE_COLOUR ( '', #37525 ) ; +#100290 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100291 = EDGE_LOOP ( 'NONE', ( #24953, #96994, #36150, #90715 ) ) ; +#100292 = PRESENTATION_STYLE_ASSIGNMENT (( #69220 ) ) ; +#100293 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999969891, 0.2499999999999990286, -0.02000000000000000042 ) ) ; +#100294 = AXIS2_PLACEMENT_3D ( 'NONE', #93223, #78952, #100298 ) ; +#100295 = VECTOR ( 'NONE', #68927, 1000.000000000000000 ) ; +#100296 = STYLED_ITEM ( 'NONE', ( #56158 ), #54611 ) ; +#100297 = ORIENTED_EDGE ( 'NONE', *, *, #74819, .F. ) ; +#100299 = CARTESIAN_POINT ( 'NONE', ( 7.950000000000000178, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#100298 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100300 = ORIENTED_EDGE ( 'NONE', *, *, #18062, .F. ) ; +#100301 = ORIENTED_EDGE ( 'NONE', *, *, #65181, .T. ) ; +#100303 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100302 = DIRECTION ( 'NONE', ( 0.7071045084557415761, -0.7071090539100487460, 0.000000000000000000 ) ) ; +#100304 = FILL_AREA_STYLE ('',( #69231 ) ) ; +#100305 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #29764 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #81849, #11283, #3217 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100306 = STYLED_ITEM ( 'NONE', ( #58305 ), #61746 ) ; +#100307 = LINE ( 'NONE', #75438, #4138 ) ; +#100308 = EDGE_CURVE ( 'NONE', #56373, #71780, #60835, .T. ) ; +#100309 = CARTESIAN_POINT ( 'NONE', ( -3.149999999999970157, -0.09999999999999997780, 0.000000000000000000 ) ) ; +#100310 = CARTESIAN_POINT ( 'NONE', ( -0.1525568181818189872, -1.164082792207790096, 0.8100000000000000533 ) ) ; +#100311 = PRESENTATION_STYLE_ASSIGNMENT (( #69235 ) ) ; +#100312 = VECTOR ( 'NONE', #13065, 1000.000000000000114 ) ; +#100313 = CARTESIAN_POINT ( 'NONE', ( -0.009862718265029700795, -1.085974092738730024, 0.8100000000000000533 ) ) ; +#100314 = PRODUCT_DEFINITION_SHAPE ( 'NONE', 'NONE', #100950 ) ; +#100315 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100316 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100317 = ORIENTED_EDGE ( 'NONE', *, *, #85460, .T. ) ; +#100318 = VERTEX_POINT ( 'NONE', #21495 ) ; +#100319 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100320 = SURFACE_STYLE_FILL_AREA ( #15126 ) ; +#100321 = CARTESIAN_POINT ( 'NONE', ( 1.095142431513040027, -1.118172950060400073, 0.8299999999999999600 ) ) ; +#100322 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #74010 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #7087, #54676, #30629 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100323 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.175494350822289960E-30, -1.000000000000000000 ) ) ; +#100324 = CARTESIAN_POINT ( 'NONE', ( 1.149999999999999911, 14.25000000000000000, 0.03429000000000000103 ) ) ; +#100325 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100326 = ADVANCED_FACE ( 'NONE', ( #82306 ), #14289, .F. ) ; +#100327 = ORIENTED_EDGE ( 'NONE', *, *, #33815, .T. ) ; +#100328 = EDGE_CURVE ( 'NONE', #22417, #98998, #37833, .T. ) ; +#100329 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100330 = STYLED_ITEM ( 'NONE', ( #6595 ), #99484 ) ; +#100331 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100332 = CARTESIAN_POINT ( 'NONE', ( 13.17837699999999934, 9.889034999999999798, 0.8648700000000000276 ) ) ; +#100333 = SURFACE_STYLE_USAGE ( .BOTH. , #62685 ) ; +#100334 = FACE_OUTER_BOUND ( 'NONE', #84577, .T. ) ; +#100335 = FILL_AREA_STYLE_COLOUR ( '', #31731 ) ; +#100336 = SURFACE_STYLE_FILL_AREA ( #40716 ) ; +#100337 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23886 ), #77648 ) ; +#100338 = FILL_AREA_STYLE_COLOUR ( '', #29327 ) ; +#100339 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100340 = VECTOR ( 'NONE', #33747, 1000.000000000000000 ) ; +#100341 = DIRECTION ( 'NONE', ( -0.9999999999319444388, -1.166666699999935221E-05, -0.000000000000000000 ) ) ; +#100342 = PLANE ( 'NONE', #86503 ) ; +#100343 = CARTESIAN_POINT ( 'NONE', ( 4.847552999999999557, 4.418599000000000387, 0.8991599999999999593 ) ) ; +#100344 = STYLED_ITEM ( 'NONE', ( #90747 ), #3995 ) ; +#100345 = ADVANCED_FACE ( 'NONE', ( #36334 ), #75144, .T. ) ; +#100346 = DIRECTION ( 'NONE', ( 0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#100347 = PRODUCT_DEFINITION_CONTEXT ( 'detailed design', #28059, 'design' ) ; +#100348 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100349 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#100350 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999999556, 0.4999999999999993339, -5.977360615245821520E-90 ) ) ; +#100351 = ORIENTED_EDGE ( 'NONE', *, *, #35326, .F. ) ; +#100352 = FILL_AREA_STYLE_COLOUR ( '', #69790 ) ; +#100353 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #47674, 'distance_accuracy_value', 'NONE'); +#100354 = FACE_OUTER_BOUND ( 'NONE', #65759, .T. ) ; +#100355 = CARTESIAN_POINT ( 'NONE', ( 15.15000000000000036, 6.250000000000000000, 0.03429000000000000103 ) ) ; +#100356 = EDGE_CURVE ( 'NONE', #94599, #93361, #55198, .T. ) ; +#100357 = CARTESIAN_POINT ( 'NONE', ( 1.755956893679319952, -1.501723168847330259, 0.8300000000000011813 ) ) ; +#100358 = PRESENTATION_STYLE_ASSIGNMENT (( #84655 ) ) ; +#100359 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #23917 ), #93954 ) ; +#100360 = VERTEX_POINT ( 'NONE', #40363 ) ; +#100361 = FILL_AREA_STYLE ('',( #20370 ) ) ; +#100362 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #1332, 'distance_accuracy_value', 'NONE'); +#100364 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100363 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #89074 ), #82583 ) ; +#100365 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #54899 ), #27134 ) ; +#100366 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #25445, 'distance_accuracy_value', 'NONE'); +#100367 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100368 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100369 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100370 = ORIENTED_EDGE ( 'NONE', *, *, #65855, .T. ) ; +#100372 = ORIENTED_EDGE ( 'NONE', *, *, #21909, .T. ) ; +#100371 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #10765 ), #97271 ) ; +#100373 = CARTESIAN_POINT ( 'NONE', ( 9.150000000000000355, 14.25000000000000000, 0.000000000000000000 ) ) ; +#100374 = ORIENTED_EDGE ( 'NONE', *, *, #14653, .F. ) ; +#100375 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #58466 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #63249, #32591, #26442 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100376 = CYLINDRICAL_SURFACE ( 'NONE', #915, 1.200947669413299890 ) ; +#100377 = LINE ( 'NONE', #62232, #5922 ) ; +#100378 = SURFACE_SIDE_STYLE ('',( #85683 ) ) ; +#100379 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100380 = CARTESIAN_POINT ( 'NONE', ( 1.633333333333323312, -3.500000000000000000, 0.000000000000000000 ) ) ; +#100381 = PRODUCT_CONTEXT ( 'NONE', #16812, 'mechanical' ) ; +#100382 = LINE ( 'NONE', #14187, #85074 ) ; +#100383 = EDGE_CURVE ( 'NONE', #98852, #32313, #8593, .T. ) ; +#100384 = PLANE ( 'NONE', #97886 ) ; +#100386 = ORIENTED_EDGE ( 'NONE', *, *, #84322, .T. ) ; +#100385 = VERTEX_POINT ( 'NONE', #7593 ) ; +#100387 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100388 = ORIENTED_EDGE ( 'NONE', *, *, #39923, .T. ) ; +#100389 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100391 = PLANE ( 'NONE', #8763 ) ; +#100390 = CARTESIAN_POINT ( 'NONE', ( 7.450000000000000178, 15.15000000000000036, 0.03429000000000000103 ) ) ; +#100392 = ORIENTED_EDGE ( 'NONE', *, *, #10600, .F. ) ; +#100393 = EDGE_CURVE ( 'NONE', #83845, #21657, #25692, .T. ) ; +#100394 = ORIENTED_EDGE ( 'NONE', *, *, #51365, .F. ) ; +#100396 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100395 = CARTESIAN_POINT ( 'NONE', ( -1.723820061220085353, -3.100000000000000533, 0.000000000000000000 ) ) ; +#100397 = STYLED_ITEM ( 'NONE', ( #86551 ), #99658 ) ; +#100398 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666639962, -0.9000000000000001332, 0.000000000000000000 ) ) ; +#100399 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100400 = CARTESIAN_POINT ( 'NONE', ( -0.3662337662337660227, -1.079220779220779969, 0.8299999999999999600 ) ) ; +#100401 = ORIENTED_EDGE ( 'NONE', *, *, #35696, .F. ) ; +#100402 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100403 = ORIENTED_EDGE ( 'NONE', *, *, #50045, .F. ) ; +#100404 = ORIENTED_EDGE ( 'NONE', *, *, #78167, .T. ) ; +#100405 = PRESENTATION_STYLE_ASSIGNMENT (( #38258 ) ) ; +#100406 = VECTOR ( 'NONE', #1194, 1000.000000000000000 ) ; +#100407 = SURFACE_STYLE_FILL_AREA ( #14722 ) ; +#100408 = CARTESIAN_POINT ( 'NONE', ( -3.099999999999989875, 2.299999999999999822, -0.02000000000000000042 ) ) ; +#100409 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100411 = ORIENTED_EDGE ( 'NONE', *, *, #89798, .T. ) ; +#100410 = CARTESIAN_POINT ( 'NONE', ( -1.050000000000000044, -3.099999999999989875, 0.000000000000000000 ) ) ; +#100412 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100413 = SURFACE_STYLE_USAGE ( .BOTH. , #71418 ) ; +#100414 = FILL_AREA_STYLE_COLOUR ( '', #74989 ) ; +#100415 = ORIENTED_EDGE ( 'NONE', *, *, #80195, .T. ) ; +#100417 = FILL_AREA_STYLE ('',( #60275 ) ) ; +#100416 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 0.8999999999999989120, 0.8299999999999999600 ) ) ; +#100418 = ORIENTED_EDGE ( 'NONE', *, *, #95502, .T. ) ; +#100419 = VERTEX_POINT ( 'NONE', #84779 ) ; +#100420 = CARTESIAN_POINT ( 'NONE', ( 6.250000000000000000, 1.149999999999999911, 0.03429000000000000103 ) ) ; +#100421 = PLANE ( 'NONE', #69310 ) ; +#100422 = CARTESIAN_POINT ( 'NONE', ( -0.3774402512590340208, -1.154769547699080023, 0.8100000000000000533 ) ) ; +#100423 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #14551, #48661, #46204, #63966 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100424 = SURFACE_STYLE_USAGE ( .BOTH. , #21938 ) ; +#100425 = ADVANCED_FACE ( 'NONE', ( #31172 ), #93418, .F. ) ; +#100426 = CARTESIAN_POINT ( 'NONE', ( 1.363156991944870056, -1.321802795360440319, 0.8299999999999997380 ) ) ; +#100427 = ORIENTED_EDGE ( 'NONE', *, *, #90215, .T. ) ; +#100428 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100429 = CARTESIAN_POINT ( 'NONE', ( 0.08699603081118000014, -1.280379325981960026, 0.8100000000000000533 ) ) ; +#100430 = ORIENTED_EDGE ( 'NONE', *, *, #36956, .F. ) ; +#100431 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100432 = FACE_OUTER_BOUND ( 'NONE', #53791, .T. ) ; +#100433 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #11911, 'distance_accuracy_value', 'NONE'); +#100434 = AXIS2_PLACEMENT_3D ( 'NONE', #40325, #94898, #1001 ) ; +#100435 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100436 = CARTESIAN_POINT ( 'NONE', ( 1.705268638847220242, -0.9625006208768249749, 0.8299999999999999600 ) ) ; +#100437 = SURFACE_SIDE_STYLE ('',( #98965 ) ) ; +#100438 = SURFACE_SIDE_STYLE ('',( #85740 ) ) ; +#100439 = LINE ( 'NONE', #46423, #15206 ) ; +#100440 = EDGE_CURVE ( 'NONE', #33665, #73476, #9122, .T. ) ; +#100441 = VECTOR ( 'NONE', #52895, 1000.000000000000000 ) ; +#100442 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.01000000000000000021, 0.1250000000000000000 ) ) ; +#100443 = AXIS2_PLACEMENT_3D ( 'NONE', #57653, #56640, #88753 ) ; +#100444 = EDGE_CURVE ( 'NONE', #83048, #18482, #46987, .T. ) ; +#100445 = SURFACE_STYLE_FILL_AREA ( #76407 ) ; +#100446 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#100447 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100448 = STYLED_ITEM ( 'NONE', ( #95630 ), #78904 ) ; +#100449 = EDGE_CURVE ( 'NONE', #50459, #54332, #92426, .T. ) ; +#100450 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100451 = STYLED_ITEM ( 'NONE', ( #4920 ), #16881 ) ; +#100453 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100452 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100454 = SURFACE_STYLE_FILL_AREA ( #39293 ) ; +#100455 = FILL_AREA_STYLE ('',( #7063 ) ) ; +#100456 = LINE ( 'NONE', #66547, #83771 ) ; +#100457 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #30505 ), #20707 ) ; +#100458 = EDGE_CURVE ( 'NONE', #87470, #2199, #31675, .T. ) ; +#100459 = AXIS2_PLACEMENT_3D ( 'NONE', #10615, #87820, #88826 ) ; +#100460 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #44457, 'distance_accuracy_value', 'NONE'); +#100461 = ORIENTED_EDGE ( 'NONE', *, *, #7765, .F. ) ; +#100463 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #31786 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #51516, #43812, #7933 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100462 = SURFACE_STYLE_FILL_AREA ( #79140 ) ; +#100464 = PRESENTATION_STYLE_ASSIGNMENT (( #21977 ) ) ; +#100465 = EDGE_CURVE ( 'NONE', #100777, #70863, #92907, .T. ) ; +#100466 = FILL_AREA_STYLE_COLOUR ( '', #7839 ) ; +#100467 = PLANE ( 'NONE', #79693 ) ; +#100468 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100469 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100470 = FILL_AREA_STYLE ('',( #39308 ) ) ; +#100471 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100472 = EDGE_CURVE ( 'NONE', #12661, #39755, #38840, .T. ) ; +#100473 = ORIENTED_EDGE ( 'NONE', *, *, #20852, .T. ) ; +#100474 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100475 = ADVANCED_FACE ( 'NONE', ( #71493 ), #46458, .F. ) ; +#100476 = ORIENTED_EDGE ( 'NONE', *, *, #5083, .F. ) ; +#100477 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100478 = FILL_AREA_STYLE_COLOUR ( '', #36616 ) ; +#100479 = CARTESIAN_POINT ( 'NONE', ( -0.1271088354660659947, -0.9625852181168450539, 0.8299999999999999600 ) ) ; +#100480 = CARTESIAN_POINT ( 'NONE', ( -0.2079889469064460095, -1.408946430034399899, 0.8299999999999995159 ) ) ; +#100481 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, -1.355252715606880049E-16 ) ) ; +#100482 = SHAPE_REPRESENTATION_RELATIONSHIP ( 'NONE' , 'NONE' , #44181, #98714 ) ; +#100483 = CARTESIAN_POINT ( 'NONE', ( 1.300000000000000266, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#100484 = ORIENTED_EDGE ( 'NONE', *, *, #90707, .F. ) ; +#100485 = FILL_AREA_STYLE_COLOUR ( '', #46779 ) ; +#100486 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100487 = EDGE_LOOP ( 'NONE', ( #24736, #54220, #54687, #94353 ) ) ; +#100488 = COLOUR_RGB ( '',1.000000000000000000, 1.000000000000000000, 1.000000000000000000 ) ; +#100489 = VERTEX_POINT ( 'NONE', #81690 ) ; +#100490 = AXIS2_PLACEMENT_3D ( 'NONE', #99705, #83002, #13466 ) ; +#100491 = CARTESIAN_POINT ( 'NONE', ( 1.178090748447750080, -1.443574297695930264, 0.8299999999999999600 ) ) ; +#100492 = LINE ( 'NONE', #68946, #78914 ) ; +#100493 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100494 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #64776 ) ) ; +#100495 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100496 = ADVANCED_FACE ( 'NONE', ( #25552 ), #2056, .T. ) ; +#100497 = FACE_OUTER_BOUND ( 'NONE', #33083, .T. ) ; +#100499 = VERTEX_POINT ( 'NONE', #95949 ) ; +#100498 = ORIENTED_EDGE ( 'NONE', *, *, #64516, .F. ) ; +#100500 = FILL_AREA_STYLE_COLOUR ( '', #26241 ) ; +#100501 = LINE ( 'NONE', #84800, #59445 ) ; +#100502 = ORIENTED_EDGE ( 'NONE', *, *, #57985, .T. ) ; +#100503 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55583 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #55674, #39828, #92409 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100504 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #46385, #31090, #15742, #70379 ), + .UNSPECIFIED., .F., .F., + ( 4, 4 ), + ( 0.000000000000000000, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100506 = CARTESIAN_POINT ( 'NONE', ( 0.2999999999999999889, -3.149999999999979927, -0.02000000000000000042 ) ) ; +#100505 = CARTESIAN_POINT ( 'NONE', ( 2.699999999999992184, 3.500000000000000444, 0.000000000000000000 ) ) ; +#100507 = EDGE_LOOP ( 'NONE', ( #95735, #95466, #37885, #82136 ) ) ; +#100508 = EDGE_CURVE ( 'NONE', #4538, #76676, #18345, .T. ) ; +#100509 = CIRCLE ( 'NONE', #22358, 0.1000000000000000472 ) ; +#100510 = ORIENTED_EDGE ( 'NONE', *, *, #13001, .F. ) ; +#100511 = CARTESIAN_POINT ( 'NONE', ( -3.383333333333326642, 0.8999999999999990230, 1.747825839084889375E-76 ) ) ; +#100512 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100513 = LINE ( 'NONE', #91482, #76351 ) ; +#100514 = SURFACE_STYLE_FILL_AREA ( #22538 ) ; +#100515 = ORIENTED_EDGE ( 'NONE', *, *, #72821, .F. ) ; +#100516 = EDGE_CURVE ( 'NONE', #72386, #99462, #26057, .T. ) ; +#100517 = ORIENTED_EDGE ( 'NONE', *, *, #79589, .T. ) ; +#100518 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #59229, #96957, #12137, #52049, #89819, #4547, #34728, #11625, #4055 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 2, 2, 4 ), + ( 0.000000000000000000, 0.2499999999999987232, 0.3749999999999981126, 0.4999999999999974465, 1.000000000000000000 ), + .UNSPECIFIED. ) ; +#100519 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100520 = EDGE_LOOP ( 'NONE', ( #64885, #43335, #87200, #18445 ) ) ; +#100521 = SURFACE_STYLE_USAGE ( .BOTH. , #38385 ) ; +#100522 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87613 ), #56675 ) ; +#100523 = VECTOR ( 'NONE', #16047, 1000.000000000000000 ) ; +#100524 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #53356 ), #56681 ) ; +#100525 = EDGE_CURVE ( 'NONE', #12156, #5154, #58225, .T. ) ; +#100527 = ORIENTED_EDGE ( 'NONE', *, *, #49645, .T. ) ; +#100526 = CARTESIAN_POINT ( 'NONE', ( 3.499999999999998668, -1.900000000000000133, 0.8299999999999999600 ) ) ; +#100528 = VECTOR ( 'NONE', #43487, 1000.000000000000000 ) ; +#100529 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100530 = SURFACE_STYLE_FILL_AREA ( #54206 ) ; +#100531 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100532 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100533 = VERTEX_POINT ( 'NONE', #74009 ) ; +#100534 = SURFACE_STYLE_FILL_AREA ( #21061 ) ; +#100535 = CLOSED_SHELL ( 'NONE', ( #56789, #74097, #10946, #92670, #78382, #22765 ) ) ; +#100536 = CARTESIAN_POINT ( 'NONE', ( 1.071224486614660298, 1.221896575926969986, 0.8100000000000000533 ) ) ; +#100537 = ORIENTED_EDGE ( 'NONE', *, *, #83274, .F. ) ; +#100538 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #15807 ), #72914 ) ; +#100539 = PRESENTATION_STYLE_ASSIGNMENT (( #92962 ) ) ; +#100540 = COLOUR_RGB ( '',0.4392156862745097978, 0.4392156862745097978, 0.4392156862745097978 ) ; +#100541 = AXIS2_PLACEMENT_3D ( 'NONE', #7165, #69516, #46544 ) ; +#100543 = ORIENTED_EDGE ( 'NONE', *, *, #14052, .T. ) ; +#100542 = FACE_OUTER_BOUND ( 'NONE', #43921, .T. ) ; +#100544 = EDGE_CURVE ( 'NONE', #29659, #79876, #17343, .T. ) ; +#100546 = FILL_AREA_STYLE ('',( #21554 ) ) ; +#100545 = CIRCLE ( 'NONE', #56698, 0.1099999999999998479 ) ; +#100547 = DIRECTION ( 'NONE', ( -0.000000000000000000, 1.000000000000000000, 0.000000000000000000 ) ) ; +#100548 = CARTESIAN_POINT ( 'NONE', ( 4.032300000000000217, 11.25741999999999976, 0.8991599999999999593 ) ) ; +#100549 = CARTESIAN_POINT ( 'NONE', ( 1.724073170230389973, -1.220939016933670018, 0.8099999999999996092 ) ) ; +#100550 = ORIENTED_EDGE ( 'NONE', *, *, #10179, .T. ) ; +#100551 = PRESENTATION_STYLE_ASSIGNMENT (( #89526 ) ) ; +#100552 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100553 = LINE ( 'NONE', #14364, #64563 ) ; +#100554 = SURFACE_STYLE_FILL_AREA ( #69521 ) ; +#100555 = EDGE_CURVE ( 'NONE', #15330, #50837, #33199, .T. ) ; +#100556 = AXIS2_PLACEMENT_3D ( 'NONE', #95459, #33729, #25568 ) ; +#100557 = CARTESIAN_POINT ( 'NONE', ( -1.076179938779914913, 3.099999999999990319, -0.02000000000000000042 ) ) ; +#100558 = SURFACE_STYLE_FILL_AREA ( #8180 ) ; +#100559 = VECTOR ( 'NONE', #48743, 1000.000000000000000 ) ; +#100560 = ORIENTED_EDGE ( 'NONE', *, *, #73729, .T. ) ; +#100561 = CARTESIAN_POINT ( 'NONE', ( -2.500000000000000000, 3.149999999999999911, 0.000000000000000000 ) ) ; +#100562 = SURFACE_SIDE_STYLE ('',( #7179 ) ) ; +#100563 = ORIENTED_EDGE ( 'NONE', *, *, #24532, .T. ) ; +#100564 = VECTOR ( 'NONE', #63188, 1000.000000000000000 ) ; +#100565 = PLANE ( 'NONE', #45452 ) ; +#100567 = LINE ( 'NONE', #52259, #28181 ) ; +#100566 = FILL_AREA_STYLE_COLOUR ( '', #36103 ) ; +#100568 = SURFACE_STYLE_FILL_AREA ( #7183 ) ; +#100569 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100570 = VECTOR ( 'NONE', #50283, 999.9999999999998863 ) ; +#100571 = ORIENTED_EDGE ( 'NONE', *, *, #25541, .T. ) ; +#100572 = CARTESIAN_POINT ( 'NONE', ( 1.837535075162280318, -0.9500768360162830106, 0.8100000000000008304 ) ) ; +#100573 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #33615 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #43077, #11847, #28759 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100574 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100575 = CARTESIAN_POINT ( 'NONE', ( 14.25000000000000000, 10.50000000000000000, 0.03429000000000000103 ) ) ; +#100576 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100577 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100578 = PRESENTATION_STYLE_ASSIGNMENT (( #84878 ) ) ; +#100579 = SURFACE_SIDE_STYLE ('',( #46577 ) ) ; +#100580 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100581 = SURFACE_STYLE_USAGE ( .BOTH. , #60935 ) ; +#100582 = SURFACE_STYLE_FILL_AREA ( #39950 ) ; +#100583 = DIRECTION ( 'NONE', ( -1.175494350822289960E-30, -0.000000000000000000, 1.000000000000000000 ) ) ; +#100584 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100585 = CARTESIAN_POINT ( 'NONE', ( 4.332300000000000040, 10.33511999999999986, 0.8648700000000000276 ) ) ; +#100586 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #9017 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #27536, #68303, #90291 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100587 = ORIENTED_EDGE ( 'NONE', *, *, #32623, .T. ) ; +#100588 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100589 = EDGE_CURVE ( 'NONE', #78794, #67492, #19369, .T. ) ; +#100590 = VERTEX_POINT ( 'NONE', #56193 ) ; +#100591 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100593 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100592 = CARTESIAN_POINT ( 'NONE', ( -0.6999999999999829692, 0.01000000000000000021, 1.149999999999999911 ) ) ; +#100595 = STYLED_ITEM ( 'NONE', ( #12268 ), #16374 ) ; +#100594 = CARTESIAN_POINT ( 'NONE', ( -1.139646564935959949, -1.515470133326519919, 0.8299999999999981837 ) ) ; +#100596 = CARTESIAN_POINT ( 'NONE', ( 1.100000000000000089, 3.520000000000000018, -0.02000000000000000042 ) ) ; +#100597 = VECTOR ( 'NONE', #10481, 1000.000000000000000 ) ; +#100598 = CARTESIAN_POINT ( 'NONE', ( 0.04622384033856599683, -1.137681993439920047, 0.8299999999999999600 ) ) ; +#100599 = PRESENTATION_STYLE_ASSIGNMENT (( #69569 ) ) ; +#100600 = CLOSED_SHELL ( 'NONE', ( #91179, #49991, #75681, #8639, #70243, #14932, #20578, #47549, #13121, #89634, #58809, #53042, #83837, #74608, #5206, #11946, #9178, #43772, #87664, #92267, #24788, #36471, #2979, #99641, #83262, #83317, #75838, #45972, #6576, #56996, #85607, #26114, #95768, #4754, #3469, #46867, #97095, #25437, #56867, #59708, #76363, #21636, #3221, #9801 ) ) ; +#100601 = ORIENTED_EDGE ( 'NONE', *, *, #44534, .F. ) ; +#100602 = CARTESIAN_POINT ( 'NONE', ( 0.2761799387799149796, 3.099999999999980105, 0.000000000000000000 ) ) ; +#100603 = PRESENTATION_STYLE_ASSIGNMENT (( #53776 ) ) ; +#100604 = AXIS2_PLACEMENT_3D ( 'NONE', #6584, #12226, #74609 ) ; +#100605 = VECTOR ( 'NONE', #26883, 1000.000000000000000 ) ; +#100606 = LINE ( 'NONE', #70084, #8365 ) ; +#100607 = ORIENTED_EDGE ( 'NONE', *, *, #41699, .T. ) ; +#100608 = SURFACE_STYLE_USAGE ( .BOTH. , #23150 ) ; +#100609 = SURFACE_STYLE_USAGE ( .BOTH. , #38968 ) ; +#100610 = ORIENTED_EDGE ( 'NONE', *, *, #11964, .T. ) ; +#100611 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100612 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100613 = VECTOR ( 'NONE', #94374, 1000.000000000000000 ) ; +#100614 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100615 = CARTESIAN_POINT ( 'NONE', ( 0.2899999999999999800, -0.005000000000000000104, 0.1400000000000000133 ) ) ; +#100616 = CARTESIAN_POINT ( 'NONE', ( -0.3116883116883120142, -1.314082792207790007, 0.8099999999999442091 ) ) ; +#100617 = SURFACE_STYLE_FILL_AREA ( #9254 ) ; +#100618 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100619 = VERTEX_POINT ( 'NONE', #95442 ) ; +#100621 = STYLED_ITEM ( 'NONE', ( #46056 ), #43846 ) ; +#100620 = SURFACE_STYLE_FILL_AREA ( #29789 ) ; +#100622 = FILL_AREA_STYLE ('',( #44122 ) ) ; +#100623 = EDGE_CURVE ( 'NONE', #23326, #73941, #10100, .T. ) ; +#100624 = ORIENTED_EDGE ( 'NONE', *, *, #14614, .T. ) ; +#100625 = PRESENTATION_STYLE_ASSIGNMENT (( #22981 ) ) ; +#100626 = FILL_AREA_STYLE ('',( #69599 ) ) ; +#100627 = FACE_OUTER_BOUND ( 'NONE', #24438, .T. ) ; +#100628 = ORIENTED_EDGE ( 'NONE', *, *, #51278, .F. ) ; +#100629 = VERTEX_POINT ( 'NONE', #2554 ) ; +#100630 = SURFACE_SIDE_STYLE ('',( #69603 ) ) ; +#100631 = VERTEX_POINT ( 'NONE', #35233 ) ; +#100632 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #49014 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #68657, #74345, #86006 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100633 = EDGE_CURVE ( 'NONE', #51654, #25563, #97928, .T. ) ; +#100634 = EDGE_LOOP ( 'NONE', ( #91552, #31249, #39018, #5171 ) ) ; +#100635 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #79592 ), #19288 ) ; +#100637 = EDGE_LOOP ( 'NONE', ( #37989, #63858, #19258, #63558 ) ) ; +#100636 = PRESENTATION_STYLE_ASSIGNMENT (( #39000 ) ) ; +#100638 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100639 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100640 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100641 = LINE ( 'NONE', #85958, #39549 ) ; +#100642 = CARTESIAN_POINT ( 'NONE', ( -3.500000000000000000, 2.700000000000000178, 0.1829999999999999960 ) ) ; +#100643 = SURFACE_SIDE_STYLE ('',( #94087 ) ) ; +#100644 = ORIENTED_EDGE ( 'NONE', *, *, #13995, .F. ) ; +#100645 = EDGE_CURVE ( 'NONE', #6488, #31444, #4545, .T. ) ; +#100646 = SURFACE_STYLE_USAGE ( .BOTH. , #52336 ) ; +#100647 = FILL_AREA_STYLE_COLOUR ( '', #52562 ) ; +#100648 = VERTEX_POINT ( 'NONE', #67817 ) ; +#100649 = STYLED_ITEM ( 'NONE', ( #30002 ), #55451 ) ; +#100650 = CARTESIAN_POINT ( 'NONE', ( -0.08700668169490691217, -1.163324672685462247, 0.8100000000000021627 ) ) ; +#100651 = SURFACE_STYLE_FILL_AREA ( #85463 ) ; +#100652 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100653 = ORIENTED_EDGE ( 'NONE', *, *, #31999, .T. ) ; +#100654 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #46911 ), #81223 ) ; +#100655 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100656 = ORIENTED_EDGE ( 'NONE', *, *, #83467, .F. ) ; +#100657 = EDGE_CURVE ( 'NONE', #14861, #23326, #98900, .T. ) ; +#100658 = ADVANCED_FACE ( 'NONE', ( #35732 ), #43858, .T. ) ; +#100659 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#100660 = AXIS2_PLACEMENT_3D ( 'NONE', #60325, #58826, #21476 ) ; +#100661 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #55096 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #62582, #92167, #91664 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100662 = AXIS2_PLACEMENT_3D ( 'NONE', #67767, #44776, #75949 ) ; +#100663 = EDGE_CURVE ( 'NONE', #72474, #49407, #82673, .T. ) ; +#100664 = EDGE_CURVE ( 'NONE', #55685, #85854, #51049, .T. ) ; +#100665 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100666 = ORIENTED_EDGE ( 'NONE', *, *, #66145, .T. ) ; +#100668 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #24165 ) ) ; +#100667 = SURFACE_SIDE_STYLE ('',( #84966 ) ) ; +#100669 = EDGE_LOOP ( 'NONE', ( #93564, #22247, #30382, #66398 ) ) ; +#100670 = FACE_OUTER_BOUND ( 'NONE', #42535, .T. ) ; +#100671 = CLOSED_SHELL ( 'NONE', ( #11524, #21491, #47660, #45682, #27311, #92480 ) ) ; +#100673 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100672 = SURFACE_STYLE_FILL_AREA ( #61023 ) ; +#100674 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100675 = CARTESIAN_POINT ( 'NONE', ( 1.350000000000000089, -3.099999999999969891, -0.02000000000000000042 ) ) ; +#100676 = AXIS2_PLACEMENT_3D ( 'NONE', #27062, #81195, #74011 ) ; +#100677 = EDGE_CURVE ( 'NONE', #65103, #42026, #90832, .T. ) ; +#100678 = DIRECTION ( 'NONE', ( -0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100679 = STYLED_ITEM ( 'NONE', ( #74593 ), #50444 ) ; +#100680 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100681 = FACE_OUTER_BOUND ( 'NONE', #62450, .T. ) ; +#100682 = EDGE_CURVE ( 'NONE', #50788, #43386, #5516, .T. ) ; +#100683 = SURFACE_STYLE_FILL_AREA ( #39534 ) ; +#100684 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100685 = LINE ( 'NONE', #22711, #91151 ) ; +#100686 = VERTEX_POINT ( 'NONE', #66349 ) ; +#100687 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100689 = PRESENTATION_STYLE_ASSIGNMENT (( #46156 ) ) ; +#100688 = DIRECTION ( 'NONE', ( 0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100690 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100691 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #40802, 'distance_accuracy_value', 'NONE'); +#100692 = DIRECTION ( 'NONE', ( 0.000000000000000000, -5.551115123125780237E-17, -1.000000000000000000 ) ) ; +#100693 = B_SPLINE_CURVE_WITH_KNOTS ( 'NONE', 3, + ( #32834, #44722, #63981, #14058, #95081, #70103, #93552, #71131, #24707, #25213, #55824, #75892, #37112, #68212, #99290, #29435, #85939, #23669, #81835 ), + .UNSPECIFIED., .F., .F., + ( 4, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 4 ), + ( 0.000000000000000000, 1.197303845394134246E-05, 2.343497120385893876E-05, 3.456890940840629179E-05, 4.542620540243032283E-05, 5.612172097447436312E-05, 6.671030612278566600E-05, 7.702883839841156305E-05, 8.736644049909056279E-05, 9.772941444565006602E-05, 0.0001081492491671588675, 0.0001185795796453376462, 0.0001293485020067977533, 0.0001402727776367085138, 0.0001511468572178020916, 0.0001622335229154977577, 0.0001734769907284033864 ), + .UNSPECIFIED. ) ; +#100694 = FACE_OUTER_BOUND ( 'NONE', #95899, .T. ) ; +#100695 = ORIENTED_EDGE ( 'NONE', *, *, #6963, .T. ) ; +#100696 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100697 = SURFACE_SIDE_STYLE ('',( #69667 ) ) ; +#100698 = SURFACE_STYLE_FILL_AREA ( #69668 ) ; +#100699 = CARTESIAN_POINT ( 'NONE', ( -0.06452060059824049620, -1.437850337629750008, 0.8100000000000000533 ) ) ; +#100700 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100701 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100702 = DIRECTION ( 'NONE', ( 0.7071067811865485719, 0.7071067811865465735, 0.000000000000000000 ) ) ; +#100703 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #42194 ), #30699 ) ; +#100704 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #89196 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #22544, #45982, #41412 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100705 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100706 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100707 = CARTESIAN_POINT ( 'NONE', ( 8.750000000000000000, 7.099999999999999645, 0.03429000000000000103 ) ) ; +#100708 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100709 = SURFACE_STYLE_USAGE ( .BOTH. , #46176 ) ; +#100710 = PRESENTATION_STYLE_ASSIGNMENT (( #62072 ) ) ; +#100711 = COLOUR_RGB ( '',0.7529411764705882248, 0.7529411764705882248, 0.7529411764705882248 ) ; +#100712 = DIRECTION ( 'NONE', ( 0.000000000000000000, 1.000000000000000000, -0.000000000000000000 ) ) ; +#100713 = SURFACE_STYLE_FILL_AREA ( #78377 ) ; +#100714 = FILL_AREA_STYLE_COLOUR ( '', #100848 ) ; +#100715 = DIRECTION ( 'NONE', ( -0.000000000000000000, -1.000000000000000000, 0.000000000000000000 ) ) ; +#100716 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -1.091883116883120008, 0.8299999999999999600 ) ) ; +#100717 = EDGE_CURVE ( 'NONE', #93582, #34205, #13648, .T. ) ; +#100718 = ORIENTED_EDGE ( 'NONE', *, *, #41325, .F. ) ; +#100719 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #94341 ), #92718 ) ; +#100720 = CARTESIAN_POINT ( 'NONE', ( -1.400000000000000133, 0.7099999999999999645, 0.8000000000000001554 ) ) ; +#100721 = DIRECTION ( 'NONE', ( -0.7071060119555119261, -0.7071075504167462222, 0.000000000000000000 ) ) ; +#100722 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #38908 ) ) ; +#100723 = CARTESIAN_POINT ( 'NONE', ( 0.1499999999999999944, 0.1000000000000000056, 1.000000000000000000 ) ) ; +#100724 = PRESENTATION_STYLE_ASSIGNMENT (( #23264 ) ) ; +#100725 = LINE ( 'NONE', #53893, #35679 ) ; +#100726 = PRESENTATION_STYLE_ASSIGNMENT (( #68184 ) ) ; +#100727 = ADVANCED_FACE ( 'NONE', ( #58718 ), #82191, .T. ) ; +#100728 = ORIENTED_EDGE ( 'NONE', *, *, #98711, .F. ) ; +#100730 = STYLED_ITEM ( 'NONE', ( #76361 ), #55718 ) ; +#100729 = FILL_AREA_STYLE_COLOUR ( '', #84605 ) ; +#100731 = CARTESIAN_POINT ( 'NONE', ( 0.000000000000000000, -3.520000000000000018, 0.000000000000000000 ) ) ; +#100733 = PLANE ( 'NONE', #17700 ) ; +#100732 = VECTOR ( 'NONE', #64416, 1000.000000000000000 ) ; +#100734 = ORIENTED_EDGE ( 'NONE', *, *, #55237, .F. ) ; +#100735 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100736 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #34108 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #16006, #85468, #78327 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100737 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100738 = DIRECTION ( 'NONE', ( -0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100739 = VECTOR ( 'NONE', #35467, 1000.000000000000000 ) ; +#100740 = CARTESIAN_POINT ( 'NONE', ( 7.110293999999999670, 2.155857000000000134, 0.8991599999999999593 ) ) ; +#100741 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100742 = SURFACE_SIDE_STYLE ('',( #280 ) ) ; +#100743 = CIRCLE ( 'NONE', #56893, 0.009999999999999998473 ) ; +#100744 = VERTEX_POINT ( 'NONE', #88640 ) ; +#100745 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100746 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100747 = VECTOR ( 'NONE', #76883, 1000.000000000000000 ) ; +#100748 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #43422, 'distance_accuracy_value', 'NONE'); +#100749 = CARTESIAN_POINT ( 'NONE', ( -0.04240146891761689685, -1.428263396816370046, 0.8300000000000006262 ) ) ; +#100750 = EDGE_CURVE ( 'NONE', #68987, #37519, #58046, .T. ) ; +#100751 = ORIENTED_EDGE ( 'NONE', *, *, #30086, .T. ) ; +#100752 = ORIENTED_EDGE ( 'NONE', *, *, #37406, .T. ) ; +#100753 = EDGE_LOOP ( 'NONE', ( #15059, #92086, #91012, #53135 ) ) ; +#100754 = CYLINDRICAL_SURFACE ( 'NONE', #93352, 0.05000000000000002359 ) ; +#100755 = CARTESIAN_POINT ( 'NONE', ( -0.1055551954118710001, -1.507644428662930025, 0.8100000000000000533 ) ) ; +#100756 = CARTESIAN_POINT ( 'NONE', ( -3.266666666666659946, 1.899999999999994582, 0.000000000000000000 ) ) ; +#100757 = PLANE ( 'NONE', #43571 ) ; +#100758 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#100759 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100760 = FACE_OUTER_BOUND ( 'NONE', #89608, .T. ) ; +#100761 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100762 = STYLED_ITEM ( 'NONE', ( #49025 ), #44069 ) ; +#100763 = ORIENTED_EDGE ( 'NONE', *, *, #58539, .T. ) ; +#100764 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46375, 'distance_accuracy_value', 'NONE'); +#100765 = PLANE ( 'NONE', #1824 ) ; +#100766 = FILL_AREA_STYLE_COLOUR ( '', #5608 ) ; +#100767 = ORIENTED_EDGE ( 'NONE', *, *, #2392, .F. ) ; +#100768 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100769 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100770 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100771 = STYLED_ITEM ( 'NONE', ( #100230 ), #32588 ) ; +#100773 = EDGE_LOOP ( 'NONE', ( #79622, #5031, #64872, #10831 ) ) ; +#100772 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100775 = PLANE ( 'NONE', #33850 ) ; +#100774 = FILL_AREA_STYLE_COLOUR ( '', #100772 ) ; +#100776 = ORIENTED_EDGE ( 'NONE', *, *, #76475, .F. ) ; +#100777 = VERTEX_POINT ( 'NONE', #34557 ) ; +#100778 = SURFACE_STYLE_FILL_AREA ( #85081 ) ; +#100779 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100780 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #84580 ), #82932 ) ; +#100781 = SURFACE_STYLE_FILL_AREA ( #69753 ) ; +#100782 = PLANE ( 'NONE', #8110 ) ; +#100783 = ORIENTED_EDGE ( 'NONE', *, *, #40268, .T. ) ; +#100784 = AXIS2_PLACEMENT_3D ( 'NONE', #7269, #37510, #77801 ) ; +#100785 = EDGE_CURVE ( 'NONE', #80595, #34797, #65664, .T. ) ; +#100786 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #87884 ), #42347 ) ; +#100787 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #1457 ), #21120 ) ; +#100788 = CARTESIAN_POINT ( 'NONE', ( 2.523820061220085176, -3.099999999999960121, -0.02000000000000000042 ) ) ; +#100789 = PLANE ( 'NONE', #14788 ) ; +#100790 = ORIENTED_EDGE ( 'NONE', *, *, #83709, .F. ) ; +#100791 = FILL_AREA_STYLE_COLOUR ( '', #51941 ) ; +#100792 = LINE ( 'NONE', #23334, #44569 ) ; +#100793 = ORIENTED_EDGE ( 'NONE', *, *, #98643, .T. ) ; +#100794 = EDGE_LOOP ( 'NONE', ( #7910, #46862, #79432, #50102 ) ) ; +#100795 = LINE ( 'NONE', #15108, #76319 ) ; +#100797 = SURFACE_STYLE_USAGE ( .BOTH. , #7416 ) ; +#100796 = LINE ( 'NONE', #84602, #98187 ) ; +#100799 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #78054 ), #47062 ) ; +#100798 =( NAMED_UNIT ( * ) SI_UNIT ( $, .STERADIAN. ) SOLID_ANGLE_UNIT ( ) ); +#100800 = FILL_AREA_STYLE_COLOUR ( '', #35219 ) ; +#100801 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #46072 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #84741, #24003, #22456 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100802 = CARTESIAN_POINT ( 'NONE', ( 9.949999999999999289, 9.949999999999999289, 0.000000000000000000 ) ) ; +#100803 = CARTESIAN_POINT ( 'NONE', ( -0.01680389005683929904, -1.106837409965790053, 0.8299999999999999600 ) ) ; +#100804 = FILL_AREA_STYLE ('',( #69776 ) ) ; +#100805 = FILL_AREA_STYLE_COLOUR ( '', #22519 ) ; +#100806 = ADVANCED_FACE ( 'NONE', ( #74335 ), #88155, .T. ) ; +#100807 = ORIENTED_EDGE ( 'NONE', *, *, #78540, .T. ) ; +#100808 = FILL_AREA_STYLE_COLOUR ( '', #21925 ) ; +#100809 = ORIENTED_EDGE ( 'NONE', *, *, #61781, .T. ) ; +#100810 = CARTESIAN_POINT ( 'NONE', ( 0.4899999999999999911, 0.4849999999999999867, 0.2500000000000000000 ) ) ; +#100811 = FACE_OUTER_BOUND ( 'NONE', #47255, .T. ) ; +#100812 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100813 = CARTESIAN_POINT ( 'NONE', ( 9.705092999999999748, 12.30296300000000009, 0.8648700000000000276 ) ) ; +#100814 = LINE ( 'NONE', #93249, #79714 ) ; +#100815 = FILL_AREA_STYLE ('',( #68283 ) ) ; +#100816 =( LENGTH_UNIT ( ) NAMED_UNIT ( * ) SI_UNIT ( .MILLI., .METRE. ) ); +#100817 = ORIENTED_EDGE ( 'NONE', *, *, #94409, .T. ) ; +#100818 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100819 = CARTESIAN_POINT ( 'NONE', ( 10.22001999999999988, 2.598279999999999923, 0.8648700000000000276 ) ) ; +#100820 = CARTESIAN_POINT ( 'NONE', ( 3.500000000000000000, 3.500000000000000000, 0.1829999999999870064 ) ) ; +#100821 = DIRECTION ( 'NONE', ( 0.7071067811865474617, 0.7071067811865474617, 0.000000000000000000 ) ) ; +#100822 = STYLED_ITEM ( 'NONE', ( #70044 ), #50881 ) ; +#100823 = CARTESIAN_POINT ( 'NONE', ( -1.149999999999999911, 0.6600000000000000311, 0.8000000000000000444 ) ) ; +#100824 = SURFACE_STYLE_USAGE ( .BOTH. , #44801 ) ; +#100826 = PRESENTATION_LAYER_ASSIGNMENT ( '', '', ( #74882 ) ) ; +#100825 = PRESENTATION_STYLE_ASSIGNMENT (( #93759 ) ) ; +#100827 = SURFACE_SIDE_STYLE ('',( #71334 ) ) ; +#100828 = EDGE_CURVE ( 'NONE', #26228, #31591, #43173, .T. ) ; +#100829 = PLANE ( 'NONE', #79996 ) ; +#100830 = LINE ( 'NONE', #61192, #79401 ) ; +#100831 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100832 = SURFACE_SIDE_STYLE ('',( #55037 ) ) ; +#100833 = LINE ( 'NONE', #54013, #91342 ) ; +#100834 = CARTESIAN_POINT ( 'NONE', ( 0.09227562695330376874, -1.387881226106355115, 0.8099999999996665423 ) ) ; +#100836 = EDGE_CURVE ( 'NONE', #60396, #210, #34043, .T. ) ; +#100835 = LINE ( 'NONE', #78495, #20965 ) ; +#100837 = SURFACE_STYLE_USAGE ( .BOTH. , #1412 ) ; +#100838 = ORIENTED_EDGE ( 'NONE', *, *, #24349, .F. ) ; +#100839 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100840 = CARTESIAN_POINT ( 'NONE', ( 11.40846699999999991, 13.31658200000000036, 0.8991599999999999593 ) ) ; +#100841 = CARTESIAN_POINT ( 'NONE', ( 1.585655134885600059, -1.389169665048220148, 0.8299999999999977396 ) ) ; +#100842 = FILL_AREA_STYLE ('',( #78499 ) ) ; +#100843 = AXIS2_PLACEMENT_3D ( 'NONE', #98154, #75260, #5255 ) ; +#100844 = CARTESIAN_POINT ( 'NONE', ( 12.18628400000000056, 12.53876499999999972, 0.8991599999999999593 ) ) ; +#100845 = CYLINDRICAL_SURFACE ( 'NONE', #5728, 0.1099999999999998479 ) ; +#100846 = CARTESIAN_POINT ( 'NONE', ( 1.280295494877693674, -1.171570345189036910, 0.8099999999998818145 ) ) ; +#100847 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #92157 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #8277, #93079, #60998 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100848 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100849 = DIRECTION ( 'NONE', ( 3.358555288063679845E-32, 1.355252715606880049E-16, -1.000000000000000000 ) ) ; +#100850 = EDGE_LOOP ( 'NONE', ( #80469, #27725, #81855, #68834 ) ) ; +#100851 = SURFACE_STYLE_USAGE ( .BOTH. , #61711 ) ; +#100852 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, 1.000000000000000000 ) ) ; +#100853 = CARTESIAN_POINT ( 'NONE', ( 1.500000000000000000, 0.000000000000000000, 0.4500000000000000666 ) ) ; +#100854 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #47203 ), #7975 ) ; +#100855 = CIRCLE ( 'NONE', #32576, 0.2000000000000005107 ) ; +#100856 = LINE ( 'NONE', #86170, #15119 ) ; +#100857 = VECTOR ( 'NONE', #63987, 1000.000000000000000 ) ; +#100858 = STYLED_ITEM ( 'NONE', ( #45217 ), #6239 ) ; +#100859 = SURFACE_SIDE_STYLE ('',( #69838 ) ) ; +#100860 = ORIENTED_EDGE ( 'NONE', *, *, #76447, .T. ) ; +#100861 = ORIENTED_EDGE ( 'NONE', *, *, #12460, .T. ) ; +#100862 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100863 = ORIENTED_EDGE ( 'NONE', *, *, #24455, .F. ) ; +#100864 = CARTESIAN_POINT ( 'NONE', ( -0.2448925227682630101, -1.469666695271939938, 0.8299999999999999600 ) ) ; +#100865 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100866 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100867 = LINE ( 'NONE', #60723, #81841 ) ; +#100868 = DIRECTION ( 'NONE', ( 0.000000000000000000, -0.000000000000000000, -1.000000000000000000 ) ) ; +#100869 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100871 = EDGE_LOOP ( 'NONE', ( #17277, #17999, #57358, #42174 ) ) ; +#100870 = ORIENTED_EDGE ( 'NONE', *, *, #64860, .F. ) ; +#100872 = CIRCLE ( 'NONE', #63515, 0.009999999999999998473 ) ; +#100873 = AXIS2_PLACEMENT_3D ( 'NONE', #55536, #71839, #78988 ) ; +#100874 = ORIENTED_EDGE ( 'NONE', *, *, #78520, .T. ) ; +#100875 = SURFACE_STYLE_FILL_AREA ( #69857 ) ; +#100876 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #46826, 'distance_accuracy_value', 'NONE'); +#100877 = FILL_AREA_STYLE_COLOUR ( '', #78977 ) ; +#100878 = EDGE_LOOP ( 'NONE', ( #61385, #1585, #99855, #13043 ) ) ; +#100879 = EDGE_CURVE ( 'NONE', #27329, #9228, #80003, .T. ) ; +#100880 = EDGE_CURVE ( 'NONE', #74624, #45346, #57037, .T. ) ; +#100881 = LINE ( 'NONE', #58012, #78045 ) ; +#100883 = SURFACE_SIDE_STYLE ('',( #69868 ) ) ; +#100882 = SURFACE_STYLE_USAGE ( .BOTH. , #38740 ) ; +#100884 = ORIENTED_EDGE ( 'NONE', *, *, #8101, .T. ) ; +#100885 = CARTESIAN_POINT ( 'NONE', ( -0.5298581286778389909, -0.9738248771264079728, 0.8100000000000000533 ) ) ; +#100886 = ORIENTED_EDGE ( 'NONE', *, *, #70774, .T. ) ; +#100887 = ORIENTED_EDGE ( 'NONE', *, *, #45867, .F. ) ; +#100888 = MECHANICAL_DESIGN_GEOMETRIC_PRESENTATION_REPRESENTATION ( '', ( #63538 ), #4815 ) ; +#100889 = DIRECTION ( 'NONE', ( -0.7071067811865475727, -0.7071067811865475727, 0.000000000000000000 ) ) ; +#100890 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100891 = FILL_AREA_STYLE ('',( #31091 ) ) ; +#100892 = FACE_OUTER_BOUND ( 'NONE', #49142, .T. ) ; +#100895 = ORIENTED_EDGE ( 'NONE', *, *, #36262, .F. ) ; +#100894 = AXIS2_PLACEMENT_3D ( 'NONE', #15573, #62104, #45698 ) ; +#100893 = CARTESIAN_POINT ( 'NONE', ( 2.100821999999999967, 10.62344799999999978, 0.8991599999999999593 ) ) ; +#100896 = DIRECTION ( 'NONE', ( 1.000000000000000000, -0.000000000000000000, 0.000000000000000000 ) ) ; +#100897 = EDGE_CURVE ( 'NONE', #61861, #94849, #5108, .T. ) ; +#100898 = DIRECTION ( 'NONE', ( -1.000000000000000000, 0.000000000000000000, -0.000000000000000000 ) ) ; +#100899 = LINE ( 'NONE', #83231, #73392 ) ; +#100900 = ORIENTED_EDGE ( 'NONE', *, *, #25453, .F. ) ; +#100902 = FACE_OUTER_BOUND ( 'NONE', #16293, .T. ) ; +#100901 = CARTESIAN_POINT ( 'NONE', ( 3.149999999999970157, -0.1000000000000000056, -0.02000000000000000042 ) ) ; +#100903 = FILL_AREA_STYLE ('',( #61276 ) ) ; +#100904 = ORIENTED_EDGE ( 'NONE', *, *, #636, .T. ) ; +#100905 = VERTEX_POINT ( 'NONE', #90439 ) ; +#100907 = DIRECTION ( 'NONE', ( 1.000000000000000000, 0.000000000000000000, 0.000000000000000000 ) ) ; +#100906 = CYLINDRICAL_SURFACE ( 'NONE', #58712, 0.04999999999999991257 ) ; +#100908 = SURFACE_STYLE_USAGE ( .BOTH. , #83737 ) ; +#100909 = SURFACE_SIDE_STYLE ('',( #40302 ) ) ; +#100910 = COLOUR_RGB ( '',0.7921568627450980005, 0.8196078431372548767, 0.9333333333333333481 ) ; +#100911 =( NAMED_UNIT ( * ) PLANE_ANGLE_UNIT ( ) SI_UNIT ( $, .RADIAN. ) ); +#100912 = LINE ( 'NONE', #45386, #83648 ) ; +#100913 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, -1.000000000000000000 ) ) ; +#100914 = DIRECTION ( 'NONE', ( 0.000000000000000000, 0.000000000000000000, 1.000000000000000000 ) ) ; +#100915 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #70740 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #50482, #22817, #93212 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100916 = EDGE_CURVE ( 'NONE', #46008, #49837, #89937, .T. ) ; +#100917 = COLOUR_RGB ( '',0.8313725490196077761, 0.6901960784313725394, 0.2196078431372548989 ) ; +#100918 = UNCERTAINTY_MEASURE_WITH_UNIT (LENGTH_MEASURE( 1.000000000000000082E-05 ), #55650, 'distance_accuracy_value', 'NONE'); +#100919 = ORIENTED_EDGE ( 'NONE', *, *, #70679, .F. ) ; +#100920 = FACE_OUTER_BOUND ( 'NONE', #41731, .T. ) ; +#100921 = EDGE_LOOP ( 'NONE', ( #23467, #2999, #26951, #63664, #47939, #94598 ) ) ; +#100922 = FACE_OUTER_BOUND ( 'NONE', #85034, .T. ) ; +#100923 = VECTOR ( 'NONE', #43906, 1000.000000000000000 ) ; +#100924 = PRESENTATION_STYLE_ASSIGNMENT (( #93366 ) ) ; +#100925 =( GEOMETRIC_REPRESENTATION_CONTEXT ( 3 ) GLOBAL_UNCERTAINTY_ASSIGNED_CONTEXT ( ( #30925 ) ) GLOBAL_UNIT_ASSIGNED_CONTEXT ( ( #49285, #47764, #32958 ) ) REPRESENTATION_CONTEXT ( 'NONE', 'WORKASPACE' ) ); +#100926 = FACE_OUTER_BOUND ( 'NONE', #39256, .T. ) ; +#100927 = AXIS2_PLACEMENT_3D ( 'NONE', #35831, #4637, #66933 ) ; +#100928 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO1', ' ', ' ', #91, #99270, $ ) ; +#100929 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO2', ' ', ' ', #91, #5709, $ ) ; +#100930 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO3', ' ', ' ', #91, #84367, $ ) ; +#100931 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO4', ' ', ' ', #99270, #4478, $ ) ; +#100932 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO5', ' ', ' ', #99270, #13169, $ ) ; +#100933 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO6', ' ', ' ', #99270, #13169, $ ) ; +#100934 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO7', ' ', ' ', #99270, #13169, $ ) ; +#100935 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO8', ' ', ' ', #99270, #41968, $ ) ; +#100936 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO9', ' ', ' ', #99270, #41968, $ ) ; +#100937 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO10', ' ', ' ', #99270, #31336, $ ) ; +#100938 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO11', ' ', ' ', #99270, #31336, $ ) ; +#100939 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO12', ' ', ' ', #99270, #31336, $ ) ; +#100940 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO13', ' ', ' ', #99270, #31336, $ ) ; +#100941 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO14', ' ', ' ', #99270, #31336, $ ) ; +#100942 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO15', ' ', ' ', #99270, #31336, $ ) ; +#100943 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO16', ' ', ' ', #99270, #31336, $ ) ; +#100944 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO17', ' ', ' ', #99270, #31336, $ ) ; +#100945 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO18', ' ', ' ', #99270, #31336, $ ) ; +#100946 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO19', ' ', ' ', #99270, #31336, $ ) ; +#100947 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO20', ' ', ' ', #99270, #31336, $ ) ; +#100948 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO21', ' ', ' ', #99270, #31336, $ ) ; +#100949 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO22', ' ', ' ', #99270, #31336, $ ) ; +#100950 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO23', ' ', ' ', #99270, #90596, $ ) ; +#100951 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO24', ' ', ' ', #99270, #78154, $ ) ; +#100952 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO25', ' ', ' ', #99270, #67513, $ ) ; +#100953 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO26', ' ', ' ', #99270, #83113, $ ) ; +#100954 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO27', ' ', ' ', #99270, #88759, $ ) ; +#100955 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO28', ' ', ' ', #88759, #81294, $ ) ; +#100956 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO29', ' ', ' ', #81294, #30055, $ ) ; +#100957 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO30', ' ', ' ', #83113, #45029, $ ) ; +#100958 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO31', ' ', ' ', #45029, #46881, $ ) ; +#100959 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO32', ' ', ' ', #67513, #96220, $ ) ; +#100960 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO33', ' ', ' ', #96220, #22581, $ ) ; +#100961 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO34', ' ', ' ', #78154, #49458, $ ) ; +#100962 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO35', ' ', ' ', #49458, #60094, $ ) ; +#100963 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO36', ' ', ' ', #90596, #11891, $ ) ; +#100964 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO37', ' ', ' ', #11891, #43788, $ ) ; +#100965 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO38', ' ', ' ', #31336, #7504, $ ) ; +#100966 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO39', ' ', ' ', #7504, #65015, $ ) ; +#100967 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO40', ' ', ' ', #41968, #54418, $ ) ; +#100968 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO41', ' ', ' ', #54418, #63191, $ ) ; +#100969 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO42', ' ', ' ', #13169, #40706, $ ) ; +#100970 = NEXT_ASSEMBLY_USAGE_OCCURRENCE ( 'NAUO43', ' ', ' ', #40706, #69330, $ ) ; +ENDSEC; +END-ISO-10303-21; diff --git a/PCB/v2.x/libraries/3dmodels/README.md b/PCB/v2.x/libraries/3dmodels/README.md index 70727c6..3f9036f 100644 --- a/PCB/v2.x/libraries/3dmodels/README.md +++ b/PCB/v2.x/libraries/3dmodels/README.md @@ -11,7 +11,7 @@ a model that does not resolve. | `USB_C_Receptacle_HRO_TYPE-C-31-M-12.step` | J_USB1, HRO TYPE-C-31-M-12 | EasyEDA/LCSC C165948, fetched with `easyeda2kicad` | Rotated 180° and offset -1.05mm in Y so the shell legs, pegs and SMD tails land on the KiCad footprint's pads | | `SW_Alps_SKRTLAE010.step` | SW_PWR1, SW_VOL_*, SW_THR_*, SW_TRIG_DIG1 (side buttons) | EasyEDA/LCSC C110293 | Pegs, terminals and plunger already match the KiCad footprint. No offset | | `Thumbstick_ALPS_RKJXV1224005.step` | J_STICK1 (DNP) | EasyEDA/LCSC C146170 (ALPS RKJXV1224005) | **Stand-in**: the GuliKit hall stick is a drop-in for this ALPS footprint family, but its body may differ. Z offset +11.4mm puts the housing standoffs on the board | -| `BT840X_outline.step` | U_MCU1 (BT840XE) | Fanstel `bt832x_1211.stp`, same 15 x 28 mm body (license not stated) | **Stand-in**: one solid with BT832X markings and no u.FL. Rotate -90 about X, offset (0, -0.3, 0.3) | +| `ESP32-S3-MINI-1U.step` | U_MCU1, ESP32-S3-MINI-1U | Espressif `kicad-libraries` (CC-BY-SA 4.0), as is `../Espressif.pretty` | Used as supplied, no offset | Models taken from KiCad's own library (`${KICAD10_3DMODEL_DIR}`) with no local copy: diff --git a/PCB/v2.x/libraries/Espressif.kicad_sym b/PCB/v2.x/libraries/Espressif.kicad_sym new file mode 100644 index 0000000..bf0ae99 --- /dev/null +++ b/PCB/v2.x/libraries/Espressif.kicad_sym @@ -0,0 +1,1275 @@ +(kicad_symbol_lib + (version 20241209) + (generator "kicad_symbol_editor") + (generator_version "9.0") + (symbol "ESP32-S3-MINI-1" + (pin_names + (offset 1.016) + ) + (exclude_from_sim no) + (in_bom yes) + (on_board yes) + (property "Reference" "U" + (at -42.926 39.624 0) + (effects + (font + (size 1.27 1.27) + ) + (justify left) + ) + ) + (property "Value" "ESP32-S3-MINI-1" + (at 42.926 39.624 0) + (effects + (font + (size 1.27 1.27) + ) + (justify right) + ) + ) + (property "Footprint" "PCM_Espressif:ESP32-S3-MINI-1" + (at 0 -55.88 0) + (effects + (font + (size 1.27 1.27) + ) + (hide yes) + ) + ) + (property "Datasheet" "https://www.espressif.com/sites/default/files/documentation/esp32-s3-mini-1_mini-1u_datasheet_en.pdf" + (at 0 -58.42 0) + (effects + (font + (size 1.27 1.27) + ) + (hide yes) + ) + ) + (property "Description" "Smallsized module supporting 2.4 GHz WiFi (802.11 b/g/n) and Bluetooth ® 5 (LE) Built around ESP32S3 series of SoCs, Xtensa ® dualcore 32bit LX7 microprocessor Flash up to 8 MB, optional 2 MB PSRAM in chip package 39 GPIOs, rich set of peripherals Onboard PCB antenna or external antenna connector" + (at 0 0 0) + (effects + (font + (size 1.27 1.27) + ) + (hide yes) + ) + ) + (symbol "ESP32-S3-MINI-1_0_0" + (text "ESP32-S3-MINI-1" + (at -22.86 0 0) + (effects + (font + (size 2.54 2.54) + ) + ) + ) + (pin input line + (at -45.72 35.56 0) + (length 2.54) + (name "EN" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "45" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 30.48 0) + (length 2.54) + (name "GPIO15/U0RTS/ADC2_CH4/XTAL_32K_P" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "19" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 27.94 0) + (length 2.54) + (name "GPIO16/U0CTS/ADC2_CH5/XTAL_32K_N" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "20" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 22.86 0) + (length 2.54) + (name "MTCK/GPIO39/CLK_OUT3/SUBSPICS1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "35" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 20.32 0) + (length 2.54) + (name "MTDO/GPIO40/CLK_OUT2" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "36" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 17.78 0) + (length 2.54) + (name "MTDI/GPIO41/CLK_OUT1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "37" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 15.24 0) + (length 2.54) + (name "MTMS/GPIO42" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "38" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -22.86 0) + (length 2.54) + (name "GPIO26" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "26" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -25.4 0) + (length 2.54) + (name "SPIIO4/GPIO33/FSPIHD/SUBSPIHD" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "28" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -27.94 0) + (length 2.54) + (name "SPIIO5/GPIO34/FSPICS0/SUBSPICS0" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "29" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -30.48 0) + (length 2.54) + (name "SPIIO6/GPIO35/FSPID/SUBSPID" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "31" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -33.02 0) + (length 2.54) + (name "SPIIO7/GPIO36/FSPICLK/SUBSPICLK" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "32" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at -45.72 -35.56 0) + (length 2.54) + (name "SPIDQS/GPIO37/FSPIQ/SUBSPIQ" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "33" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin power_in line + (at 0 40.64 270) + (length 2.54) + (name "3V3" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "3" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin power_in line + (at 0 -40.64 90) + (length 2.54) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "2" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "42" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "43" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "46" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "47" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "48" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "49" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "50" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "51" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "52" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "53" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "54" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "55" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "56" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "57" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "58" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "59" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "60" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "61" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "62" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "63" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "64" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin passive line + (at 0 -40.64 90) + (length 2.54) + (hide yes) + (name "GND" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "65" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 35.56 180) + (length 2.54) + (name "U0TXD/GPIO43/CLK_OUT1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "39" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 33.02 180) + (length 2.54) + (name "U0RXD/GPIO44/CLK_OUT2" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "40" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 27.94 180) + (length 2.54) + (name "GPIO20/U1CTS/ADC2_CH9/CLK_OUT1/USB_D+" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "24" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 25.4 180) + (length 2.54) + (name "GPIO19/U1RTS/ADC2_CH8/CLK_OUT2/USB_D-" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "23" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 20.32 180) + (length 2.54) + (name "GPIO0/BOOT" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "4" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 17.78 180) + (length 2.54) + (name "GPIO1/TOUCH1/ADC1_CH0" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "5" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 15.24 180) + (length 2.54) + (name "GPIO2/TOUCH2/ADC1_CH1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "6" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 12.7 180) + (length 2.54) + (name "GPIO3/TOUCH3/ADC1_CH2" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "7" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 10.16 180) + (length 2.54) + (name "GPIO4/TOUCH4/ADC1_CH3" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "8" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 7.62 180) + (length 2.54) + (name "GPIO5/TOUCH5/ADC1_CH4" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "9" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 5.08 180) + (length 2.54) + (name "GPIO6/TOUCH6/ADC1_CH5" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "10" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 2.54 180) + (length 2.54) + (name "GPIO7/TOUCH7/ADC1_CH6" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "11" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 0 180) + (length 2.54) + (name "GPIO8/TOUCH8/ADC1_CH7/SUBSPICS1" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "12" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -2.54 180) + (length 2.54) + (name "GPIO9/TOUCH9/ADC1_CH8/FSPIHD/SUBSPIHD" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "13" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -5.08 180) + (length 2.54) + (name "GPIO10/TOUCH10/ADC1_CH9/FSPICS0/FSPIIO4/SUBSPICS0" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "14" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -7.62 180) + (length 2.54) + (name "GPIO11/TOUCH11/ADC2_CH0/FSPID/FSPIIO5/SUBSPID" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "15" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -10.16 180) + (length 2.54) + (name "GPIO12/TOUCH12/ADC2_CH1/FSPICLK/FSPIIO6/SUBSPICLK" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "16" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -12.7 180) + (length 2.54) + (name "GPIO13/TOUCH13/ADC2_CH2/FSPIQ/FSPIIO7/SUBSPIQ" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "17" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -15.24 180) + (length 2.54) + (name "GPIO14/TOUCH14/ADC2_CH3/FSPIWP/FSPIDQS/SUBSPIWP" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "18" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -17.78 180) + (length 2.54) + (name "GPIO17/U1TXD/ADC2_CH6" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "21" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -20.32 180) + (length 2.54) + (name "GPIO18/U1RXD/ADC2_CH7/CLK_OUT3" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "22" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -22.86 180) + (length 2.54) + (name "GPIO21" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "25" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -25.4 180) + (length 2.54) + (name "GPIO38/FSPIWP/SUBSPIWP" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "34" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -27.94 180) + (length 2.54) + (name "GPIO45" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "41" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -30.48 180) + (length 2.54) + (name "GPIO46" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "44" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -33.02 180) + (length 2.54) + (name "GPIO47/SPICLK_P/SUBSPICLK_P_DIFF" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "27" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + (pin bidirectional line + (at 45.72 -35.56 180) + (length 2.54) + (name "GPIO48/SPICLK_N/SUBSPICLK_N_DIFF" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (number "30" + (effects + (font + (size 1.27 1.27) + ) + ) + ) + ) + ) + (symbol "ESP32-S3-MINI-1_0_1" + (rectangle + (start -43.18 38.1) + (end 43.18 -38.1) + (stroke + (width 0) + (type default) + ) + (fill + (type background) + ) + ) + ) + (embedded_fonts no) + ) +) diff --git a/PCB/v2.x/libraries/Espressif.pretty/ESP32-S3-MINI-1U.kicad_mod b/PCB/v2.x/libraries/Espressif.pretty/ESP32-S3-MINI-1U.kicad_mod new file mode 100644 index 0000000..f6ca554 --- /dev/null +++ b/PCB/v2.x/libraries/Espressif.pretty/ESP32-S3-MINI-1U.kicad_mod @@ -0,0 +1,155 @@ +(footprint "ESP32-S3-MINI-1U" (version 20221018) (generator pcbnew) + (layer "F.Cu") + (descr "ESP32-S3-MINI-1 and ESP32-S3-MINI-1U") + (tags "esp32-s3") + (attr smd) + (fp_text reference "REF**" (at 0 -9.35) (layer "F.SilkS") + (effects (font (size 1 1) (thickness 0.15))) + (tstamp 3aced845-83c1-4b5c-906f-7a1884062712) + ) + (fp_text value "ESP32-S3-MINI-1U" (at 0 9.35) (layer "F.Fab") + (effects (font (size 1 1) (thickness 0.15))) + (tstamp d370559b-8633-439e-a63c-463ce266de36) + ) + (fp_text user "${REFERENCE}" (at 0 0) (layer "F.Fab") + (effects (font (size 1 1) (thickness 0.15))) + (tstamp b996e933-2e5e-48fe-8d45-4e515638782e) + ) + (fp_line (start -7.85 7.85) (end -7.85 6.8) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 99cc7708-ea73-4d45-b9c0-127e10ae8f69)) + (fp_line (start -7.7 -7.7) (end 7.7 -7.7) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 1fd9790a-5e5b-4f5e-8357-4f31651dbddd)) + (fp_line (start -7.7 7.7) (end -7.7 -7.7) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 4515bad2-291b-40f5-a915-9d187a981d64)) + (fp_line (start -6.8 -7.85) (end -8 -7.85) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 4bc87a38-c739-470d-9451-9d45503d7acf)) + (fp_line (start -6.8 7.85) (end -7.85 7.85) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp e2f149c2-370a-4f6a-8f82-a0f53f059b06)) + (fp_line (start 6.8 -7.85) (end 7.85 -7.85) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp d77c1de2-4ec8-4fbe-876f-e22ac7395dd1)) + (fp_line (start 6.8 7.85) (end 7.85 7.85) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp c84e707a-60e9-480e-86b7-f1e363936725)) + (fp_line (start 7.7 -7.7) (end 7.7 7.7) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp a63c40ac-2029-4268-bc91-5b9db4dd799a)) + (fp_line (start 7.7 7.7) (end -7.7 7.7) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp e5569d81-80f9-4e34-84b9-1bbc2598bb55)) + (fp_line (start 7.85 -7.85) (end 7.85 -6.8) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 91bf6d34-9c57-4c33-9ad7-1823f01a3191)) + (fp_line (start 7.85 7.85) (end 7.85 6.8) + (stroke (width 0.12) (type solid)) (layer "F.SilkS") (tstamp 83151023-5106-4495-aeff-aefc75dfd6c0)) + (fp_line (start -8 -8) (end -8 8) + (stroke (width 0.12) (type solid)) (layer "F.CrtYd") (tstamp 406038a6-e7cc-4630-9f35-60c0a4170172)) + (fp_line (start -8 8) (end 8 8) + (stroke (width 0.12) (type solid)) (layer "F.CrtYd") (tstamp b0064db8-ebc9-4fc5-a1b3-04116a1ad079)) + (fp_line (start 8 -8) (end -8 -8) + (stroke (width 0.12) (type solid)) (layer "F.CrtYd") (tstamp 921640b8-d1c8-4ecf-94d9-b7dea7acaf31)) + (fp_line (start 8 8) (end 8 -8) + (stroke (width 0.12) (type solid)) (layer "F.CrtYd") (tstamp b2cc1ff0-1398-4ee6-b0cc-c3393591263f)) + (fp_line (start -7.7 -7.7) (end -7.7 7.7) + (stroke (width 0.15) (type solid)) (layer "F.Fab") (tstamp b53bdfe2-a829-4adc-a4d2-d32320ab0686)) + (fp_line (start -7.7 7.7) (end 7.7 7.7) + (stroke (width 0.15) (type solid)) (layer "F.Fab") (tstamp 3d06e7e6-38a3-416f-a13d-56067d9407a3)) + (fp_line (start 7.7 -7.7) (end -7.7 -7.7) + (stroke (width 0.15) (type solid)) (layer "F.Fab") (tstamp 767d13df-5e37-488b-b6e5-02557d9d395c)) + (fp_line (start 7.7 7.7) (end 7.7 -7.7) + (stroke (width 0.15) (type solid)) (layer "F.Fab") (tstamp a00eaf83-142f-4370-9fa4-5c7e5d6e98d6)) + (pad "1" smd rect (at -7 -5.95 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e657324c-3b20-4623-90f6-370abde92247)) + (pad "2" smd rect (at -7 -5.1 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 73a2f9d8-8d4d-4a05-9c1c-3b135bae39c0)) + (pad "3" smd rect (at -7 -4.25 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp b0b9cd49-9c42-426d-9b91-8d0a9490a96f)) + (pad "4" smd rect (at -7 -3.4 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp f85fa9e5-1155-42f7-a4d1-df32decdebc7)) + (pad "5" smd rect (at -7 -2.55 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e7841aed-e4de-4b72-9775-76e69a49d568)) + (pad "6" smd rect (at -7 -1.7 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp a34e3cff-6c50-4a94-8522-adda0ca6eae0)) + (pad "7" smd rect (at -7 -0.85 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 592d08b6-6ab0-4961-bff5-b0699ae0a471)) + (pad "8" smd rect (at -7 0 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp d27b8a03-2851-40b5-b13d-cb8e50680075)) + (pad "9" smd rect (at -7 0.85 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 5d8ba9d6-3afa-48e3-8fab-8118819648af)) + (pad "10" smd rect (at -7 1.7 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp fcb8fb15-28d7-4603-a2e2-61c39a934c19)) + (pad "11" smd rect (at -7 2.55 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp b836b39b-424e-4b3b-8dd0-9505d607af83)) + (pad "12" smd rect (at -7 3.4 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 876adf5e-9e78-4269-9679-8a0ae1ce0dcf)) + (pad "13" smd rect (at -7 4.25 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp a5ea7530-e258-4c85-8803-b901cc4d59fc)) + (pad "14" smd rect (at -7 5.1 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 2c6cb2d7-5f16-47e0-a74f-2af92afff58d)) + (pad "15" smd rect (at -7 5.95 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 45b9ad65-47a5-4b6f-a59a-58ac265e32ff)) + (pad "16" smd rect (at -5.95 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp b4f1a5b7-6154-4567-9ecf-87e6abf75816)) + (pad "17" smd rect (at -5.1 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e78a8e50-fd9d-427c-ab3a-20bcf15b2fb7)) + (pad "18" smd rect (at -4.25 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 326f6338-c79c-4546-a05a-f963b87e1491)) + (pad "19" smd rect (at -3.4 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp a5f7f22c-2297-4499-8968-d6d852de406e)) + (pad "20" smd rect (at -2.55 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 14cc3771-8d04-4ece-8773-92cfd1451bbd)) + (pad "21" smd rect (at -1.7 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp c28c9a5c-d37c-4ae7-ab66-b9fbb0be875e)) + (pad "22" smd rect (at -0.85 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp aa932c5a-2809-4773-ae71-ec108b60bb9e)) + (pad "23" smd rect (at 0 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 63955a83-6880-4697-bf42-fbd4fb853378)) + (pad "24" smd rect (at 0.85 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 951d8eb6-3fac-46ae-8c3b-1238073695b4)) + (pad "25" smd rect (at 1.7 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 07e486f7-86c9-49b0-ab91-03d34cb1f77d)) + (pad "26" smd rect (at 2.55 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp bc6c7646-ee48-44f8-be85-6a8ba8d0de0e)) + (pad "27" smd rect (at 3.4 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 8af0499b-e407-4287-92a3-3739e16b7ac3)) + (pad "28" smd rect (at 4.25 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 11df0a9a-26d0-409f-990a-49d7323fbb2a)) + (pad "29" smd rect (at 5.1 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 7f723275-24d6-4eff-8e60-748d9e799816)) + (pad "30" smd rect (at 5.95 7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 714082ae-6d3a-494c-97e0-ac4d844561f3)) + (pad "31" smd rect (at 7 5.95 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 4f826aef-ba01-4542-a1b7-3bde10a82f67)) + (pad "32" smd rect (at 7 5.1 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e497919b-2743-4dc6-ac49-0312bff35d34)) + (pad "33" smd rect (at 7 4.25 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp eb68d09f-1613-4dfd-9b71-0e1f8b26b1f0)) + (pad "34" smd rect (at 7 3.4 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 7e861172-4faa-40ae-a81f-77b55482a079)) + (pad "35" smd rect (at 7 2.55 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 7e027f2a-ea31-44a5-8331-f0d4bd0124f0)) + (pad "36" smd rect (at 7 1.7 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp b63e0ecd-1d73-4890-b73d-41a0791d02d8)) + (pad "37" smd rect (at 7 0.85 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 9faf9aeb-d705-4e6f-812e-c6e53f6b85ef)) + (pad "38" smd rect (at 7 0 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e2e15bde-e756-42ae-894d-be0da99be93d)) + (pad "39" smd rect (at 7 -0.85 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 7220def5-fd75-41ae-9121-ed7d3a565613)) + (pad "40" smd rect (at 7 -1.7 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp d098f648-f4b2-416d-b854-966f357594f6)) + (pad "41" smd rect (at 7 -2.55 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 5dd0dfc1-7ccb-4d31-b8e1-651d7d8aa9a2)) + (pad "42" smd rect (at 7 -3.4 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 8cb5018d-e053-4f64-8893-b7f066a92846)) + (pad "43" smd rect (at 7 -4.25 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp d6483792-14b8-4773-8543-f97852cb29ae)) + (pad "44" smd rect (at 7 -5.1 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e1fcac5b-38a3-4e13-9305-7b74c4f4617b)) + (pad "45" smd rect (at 7 -5.95 90) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 580d8cc3-3587-4178-8649-00e89d6448d3)) + (pad "46" smd rect (at 5.95 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 115d1187-55da-4b2c-bbf1-0f4ed0428eed)) + (pad "47" smd rect (at 5.1 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 22fa1183-7658-437f-abce-a1ea1c6e9c06)) + (pad "48" smd rect (at 4.25 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp c3778ac6-b2c2-4699-9205-66c2cfd4b614)) + (pad "49" smd rect (at 3.4 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 9f5444ce-003b-4fde-baac-e1cc1cf6f0c3)) + (pad "50" smd rect (at 2.55 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 804f4a8a-9a5e-4e95-b0a4-af55cb213eb5)) + (pad "51" smd rect (at 1.7 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 5bf6aa0a-6192-42b7-bea5-561814e0e9d0)) + (pad "52" smd rect (at 0.85 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp b48d4f28-6cc4-42a3-99e8-0de40e9f1f61)) + (pad "53" smd rect (at 0 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 9841377f-19fe-4848-82b2-954ed8fd28f4)) + (pad "54" smd rect (at -0.85 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 9ff3b9ac-794c-4bf7-9e6a-fcb0b6256e34)) + (pad "55" smd rect (at -1.7 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 8daaf805-f6ae-4c8f-a4aa-24feb87c1291)) + (pad "56" smd rect (at -2.55 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 3e60f532-1ddf-4dcf-b976-b035e5364a60)) + (pad "57" smd rect (at -3.4 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp d9127026-61aa-40d3-842d-ace9aafca91a)) + (pad "58" smd rect (at -4.25 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 74f2a52f-ecad-44e0-9c5c-0991335ebd58)) + (pad "59" smd rect (at -5.1 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp f98b1d84-8430-47bb-b817-0ae62dd1291d)) + (pad "60" smd rect (at -5.95 -7) (size 0.4 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp e3a833e7-0c9c-41af-ac35-49ecd7d9c9dc)) + (pad "61" smd custom (at -1.65 -1.65) (size 0.6 0.6) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) + (options (clearance outline) (anchor rect)) + (primitives + (gr_poly + (pts + (xy 0.6 0.6) + (xy -0.6 0.6) + (xy -0.6 0) + (xy 0 -0.6) + (xy 0.6 -0.6) + ) + (width 0) (fill yes)) + ) (tstamp 29c28e74-513e-4abb-bebe-ce4d6d156196)) + (pad "61" smd rect (at -1.65 0) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp 2e834ded-fdc3-46c9-952a-e3e1b3b5a39d)) + (pad "61" smd rect (at -1.65 1.65) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp 191ac53d-46f3-4721-860d-7dff0d5203dc)) + (pad "61" smd rect (at 0 -1.65) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp a9584289-dcf1-45ad-b361-04b0ecbea7dc)) + (pad "61" smd rect (at 0 0) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp a9a62418-f170-4964-850f-1e89a1d2d04a)) + (pad "61" smd rect (at 0 1.65) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp cf7e02a5-e6d4-45bb-a3d9-e1d7ae057358)) + (pad "61" smd rect (at 1.65 -1.65) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp 16d2d7a7-7b51-4707-8d4b-74e0cabd17f9)) + (pad "61" smd rect (at 1.65 0) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp af4a11b7-aa69-4ff8-b4d0-ba35667bb9bb)) + (pad "61" smd rect (at 1.65 1.65) (size 1.2 1.2) (layers "F.Cu" "F.Paste" "F.Mask") + (zone_connect 2) (tstamp cbfe49ed-f257-408b-8449-eec3002e7401)) + (pad "62" smd rect (at -7 -7 180) (size 0.8 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 929ea914-d305-4d5c-a9c2-a7cd57167667)) + (pad "63" smd rect (at -7 7 180) (size 0.8 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp d67805db-387c-4a8f-839b-2a2e560f75e0)) + (pad "64" smd rect (at 7 7 180) (size 0.8 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp 19031a68-6f7c-490b-9ac3-1a0fb5922fa3)) + (pad "65" smd rect (at 7 -7 180) (size 0.8 0.8) (layers "F.Cu" "F.Paste" "F.Mask") (tstamp a24a0705-005d-4cbc-bbba-22e741b077a1)) + (model "${KIPRJMOD}/libraries/3dmodels/ESP32-S3-MINI-1U.step" + (offset (xyz -7.7 -7.7 0)) + (scale (xyz 1 1 1)) + (rotate (xyz 0 0 0)) + ) +) diff --git a/PCB/v2.x/libraries/SnipsControllers_Custom.kicad_sym b/PCB/v2.x/libraries/SnipsControllers_Custom.kicad_sym index 8b843c9..241ef7d 100644 --- a/PCB/v2.x/libraries/SnipsControllers_Custom.kicad_sym +++ b/PCB/v2.x/libraries/SnipsControllers_Custom.kicad_sym @@ -871,408 +871,4 @@ ) ) ) - (symbol "BT840XE" - (exclude_from_sim no) - (in_bom yes) - (on_board yes) - (property "Reference" "U" (at 0 45.085 0) (effects (font (size 1.27 1.27)))) - (property "Value" "BT840XE" (at 0 -45.085 0) (effects (font (size 1.27 1.27)))) - (property "Footprint" "SnipsControllers_Custom:BT840XE" (at 0 0 0) (effects (font (size 1.27 1.27)) (hide yes))) - (property "Datasheet" "https://www.fanstel.com/s/BT840X-p-Product-Specifications-cjd4.pdf" (at 0 0 0) (effects (font (size 1.27 1.27)) (hide yes))) - (symbol "BT840XE_0_1" - (rectangle (start -12.7 42.545) (end 12.7 -42.545) (stroke (width 0.254) (type default)) (fill (type background))) - ) - (symbol "BT840XE_1_1" - (pin bidirectional line - (at -15.24 41.27 0) - (length 2.54) - (name "P0_26" (effects (font (size 1.016 1.016)))) - (number "1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 40.01 0) - (length 2.54) - (name "P0_27" (effects (font (size 1.016 1.016)))) - (number "2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 38.73 0) - (length 2.54) - (name "P0_00" (effects (font (size 1.016 1.016)))) - (number "3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 37.47 0) - (length 2.54) - (name "P0_01" (effects (font (size 1.016 1.016)))) - (number "4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 36.2 0) - (length 2.54) - (name "P0_02" (effects (font (size 1.016 1.016)))) - (number "5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 34.93 0) - (length 2.54) - (name "P0_03" (effects (font (size 1.016 1.016)))) - (number "6" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 33.66 0) - (length 2.54) - (name "P0_09" (effects (font (size 1.016 1.016)))) - (number "7" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 32.39 0) - (length 2.54) - (name "P0_10" (effects (font (size 1.016 1.016)))) - (number "8" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 31.12 0) - (length 2.54) - (name "VDD" (effects (font (size 1.016 1.016)))) - (number "9" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 29.85 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "10" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 28.58 0) - (length 2.54) - (name "P0_11" (effects (font (size 1.016 1.016)))) - (number "11" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 27.3 0) - (length 2.54) - (name "P1_00" (effects (font (size 1.016 1.016)))) - (number "12" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 26.04 0) - (length 2.54) - (name "P0_13" (effects (font (size 1.016 1.016)))) - (number "13" (effects (font (size 1.016 1.016)))) - ) - (pin input line - (at -15.24 24.77 0) - (length 2.54) - (name "RESET" (effects (font (size 1.016 1.016)))) - (number "14" (effects (font (size 1.016 1.016)))) - ) - (pin input line - (at -15.24 23.5 0) - (length 2.54) - (name "SWDCLK" (effects (font (size 1.016 1.016)))) - (number "15" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 22.23 0) - (length 2.54) - (name "SWDIO" (effects (font (size 1.016 1.016)))) - (number "16" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 20.96 0) - (length 2.54) - (name "P1_11" (effects (font (size 1.016 1.016)))) - (number "Z0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 19.69 0) - (length 2.54) - (name "P1_12" (effects (font (size 1.016 1.016)))) - (number "Z1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 18.42 0) - (length 2.54) - (name "P1_13" (effects (font (size 1.016 1.016)))) - (number "Z2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 17.15 0) - (length 2.54) - (name "P1_14" (effects (font (size 1.016 1.016)))) - (number "Z3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 15.88 0) - (length 2.54) - (name "P1_15" (effects (font (size 1.016 1.016)))) - (number "Z4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 14.61 0) - (length 2.54) - (name "P1_10" (effects (font (size 1.016 1.016)))) - (number "Z5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 13.34 0) - (length 2.54) - (name "P1_06" (effects (font (size 1.016 1.016)))) - (number "Z6" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 12.07 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "A0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 10.8 0) - (length 2.54) - (name "P0_28" (effects (font (size 1.016 1.016)))) - (number "A1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 9.52 0) - (length 2.54) - (name "P0_29" (effects (font (size 1.016 1.016)))) - (number "A2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 8.26 0) - (length 2.54) - (name "P0_04" (effects (font (size 1.016 1.016)))) - (number "A3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 6.98 0) - (length 2.54) - (name "P0_05" (effects (font (size 1.016 1.016)))) - (number "A4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 5.72 0) - (length 2.54) - (name "P0_07" (effects (font (size 1.016 1.016)))) - (number "A5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 4.45 0) - (length 2.54) - (name "P1_08" (effects (font (size 1.016 1.016)))) - (number "A6" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 3.18 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "B0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 1.91 0) - (length 2.54) - (name "P0_25" (effects (font (size 1.016 1.016)))) - (number "B1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 0.63 0) - (length 2.54) - (name "P0_30" (effects (font (size 1.016 1.016)))) - (number "B2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -0.63 0) - (length 2.54) - (name "P0_31" (effects (font (size 1.016 1.016)))) - (number "B3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -1.91 0) - (length 2.54) - (name "P0_06" (effects (font (size 1.016 1.016)))) - (number "B4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -3.17 0) - (length 2.54) - (name "P0_08" (effects (font (size 1.016 1.016)))) - (number "B5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -4.45 0) - (length 2.54) - (name "P1_03" (effects (font (size 1.016 1.016)))) - (number "B6" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -5.71 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "C0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -6.98 0) - (length 2.54) - (name "P0_24" (effects (font (size 1.016 1.016)))) - (number "C1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -8.25 0) - (length 2.54) - (name "P0_22" (effects (font (size 1.016 1.016)))) - (number "C2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -9.52 0) - (length 2.54) - (name "P0_17" (effects (font (size 1.016 1.016)))) - (number "C3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -10.8 0) - (length 2.54) - (name "P0_15" (effects (font (size 1.016 1.016)))) - (number "C4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -12.06 0) - (length 2.54) - (name "P1_02" (effects (font (size 1.016 1.016)))) - (number "C5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -13.34 0) - (length 2.54) - (name "P1_04" (effects (font (size 1.016 1.016)))) - (number "C6" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -14.6 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "D0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -15.88 0) - (length 2.54) - (name "P0_23" (effects (font (size 1.016 1.016)))) - (number "D1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -17.14 0) - (length 2.54) - (name "P0_19" (effects (font (size 1.016 1.016)))) - (number "D2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -18.41 0) - (length 2.54) - (name "P0_16" (effects (font (size 1.016 1.016)))) - (number "D3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -19.69 0) - (length 2.54) - (name "P0_14" (effects (font (size 1.016 1.016)))) - (number "D4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -20.95 0) - (length 2.54) - (name "P1_01" (effects (font (size 1.016 1.016)))) - (number "D5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -22.22 0) - (length 2.54) - (name "P1_05" (effects (font (size 1.016 1.016)))) - (number "D6" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -23.5 0) - (length 2.54) - (name "P1_07" (effects (font (size 1.016 1.016)))) - (number "E0" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -24.77 0) - (length 2.54) - (name "P0_20" (effects (font (size 1.016 1.016)))) - (number "E1" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -26.03 0) - (length 2.54) - (name "P0_21" (effects (font (size 1.016 1.016)))) - (number "E2" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -27.3 0) - (length 2.54) - (name "P1_09" (effects (font (size 1.016 1.016)))) - (number "E3" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -28.58 0) - (length 2.54) - (name "USB_DP" (effects (font (size 1.016 1.016)))) - (number "E4" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -29.84 0) - (length 2.54) - (name "USB_DM" (effects (font (size 1.016 1.016)))) - (number "E5" (effects (font (size 1.016 1.016)))) - ) - (pin bidirectional line - (at -15.24 -31.11 0) - (length 2.54) - (name "P0_12" (effects (font (size 1.016 1.016)))) - (number "E6" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -32.39 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "F0" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -33.66 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "F1" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -34.92 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "F2" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -36.19 0) - (length 2.54) - (name "GND" (effects (font (size 1.016 1.016)))) - (number "F3" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -37.47 0) - (length 2.54) - (name "VDDH" (effects (font (size 1.016 1.016)))) - (number "F4" (effects (font (size 1.016 1.016)))) - ) - (pin passive line - (at -15.24 -38.73 0) - (length 2.54) - (name "DCCH" (effects (font (size 1.016 1.016)))) - (number "F5" (effects (font (size 1.016 1.016)))) - ) - (pin power_in line - (at -15.24 -40.0 0) - (length 2.54) - (name "VBUS" (effects (font (size 1.016 1.016)))) - (number "F6" (effects (font (size 1.016 1.016)))) - ) - ) - ) ) diff --git a/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/BT840XE.kicad_mod b/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/BT840XE.kicad_mod deleted file mode 100644 index afceb3a..0000000 --- a/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/BT840XE.kicad_mod +++ /dev/null @@ -1,103 +0,0 @@ -(footprint "BT840XE" - (version 20260206) - (generator "handmade") - (generator_version "10.0") - (layer "F.Cu") - (descr "Fanstel BT840XE nRF52840 module with SKY66112 PA and u.FL, 15 x 28 x 1.9 mm. Pad positions from the BT840X/BT840XE mechanical drawing, Product Specifications Ver 1.26 p.12 (top view). Pad names are Fanstel's. Origin is the centre of the 15 x 28 mm outline. Fanstel gives no host land pattern here: castellated lands extend 0.5 mm past the module edge and are 0.70 mm wide. Check against the Fanstel library before fab. The upper section is the shield and u.FL, with no pads under it.") - (tags "BT840XE nRF52840 Fanstel Zigbee BLE module") - (attr smd) - (fp_text reference "REF**" (at 0 -15 0) (layer "F.SilkS") - (effects (font (size 1 1) (thickness 0.15))) - ) - (fp_text value "BT840XE" (at 0 15 0) (layer "F.Fab") - (effects (font (size 1 1) (thickness 0.15))) - ) - (fp_line (start -7.5 -14.0) (end 7.5 -14.0) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_line (start 7.5 -14.0) (end 7.5 14.0) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_line (start 7.5 14.0) (end -6.5 14.0) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_line (start -6.5 14.0) (end -6.5 1.3) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_line (start -6.5 1.3) (end -7.5 1.3) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_line (start -7.5 1.3) (end -7.5 -14.0) (stroke (width 0.1) (type solid)) (layer "F.Fab")) - (fp_rect (start -7.75 -14.25) (end 8.25 14.25) (stroke (width 0.05) (type solid)) (fill no) (layer "F.CrtYd")) - (fp_line (start -7.5 -14.15) (end 7.65 -14.15) (stroke (width 0.12) (type solid)) (layer "F.SilkS")) - (fp_line (start 7.65 -14.15) (end 7.65 4.0) (stroke (width 0.12) (type solid)) (layer "F.SilkS")) - (fp_line (start -7.65 -14.15) (end -7.65 1.15) (stroke (width 0.12) (type solid)) (layer "F.SilkS")) - (fp_line (start -7.65 1.15) (end -6.8 1.15) (stroke (width 0.12) (type solid)) (layer "F.SilkS")) - (fp_circle (center -7.6 5.2) (end -7.45 5.2) (stroke (width 0.2) (type solid)) (fill no) (layer "F.SilkS")) - (pad "1" smd rect (at -6.375 5.2) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "2" smd rect (at -6.375 6.3) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "3" smd rect (at -6.375 7.4) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "4" smd rect (at -6.375 8.5) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "5" smd rect (at -6.375 9.6) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "6" smd rect (at -6.375 10.7) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "7" smd rect (at -6.375 11.8) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "8" smd rect (at -6.375 12.9) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "9" smd rect (at 7.375 12.9) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "10" smd rect (at 7.375 11.8) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "11" smd rect (at 7.375 10.7) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "12" smd rect (at 7.375 9.6) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "13" smd rect (at 7.375 8.5) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "14" smd rect (at 7.375 7.4) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "15" smd rect (at 7.375 6.3) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "16" smd rect (at 7.375 5.2) (size 1.25 0.7) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z0" smd circle (at -3.25 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z1" smd circle (at -3.25 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z2" smd circle (at -3.25 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z3" smd circle (at -3.25 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z4" smd circle (at -3.25 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z5" smd circle (at -3.25 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "Z6" smd circle (at -3.25 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A0" smd circle (at -1.75 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A1" smd circle (at -1.75 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A2" smd circle (at -1.75 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A3" smd circle (at -1.75 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A4" smd circle (at -1.75 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A5" smd circle (at -1.75 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "A6" smd circle (at -1.75 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B0" smd circle (at -0.25 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B1" smd circle (at -0.25 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B2" smd circle (at -0.25 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B3" smd circle (at -0.25 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B4" smd circle (at -0.25 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B5" smd circle (at -0.25 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "B6" smd circle (at -0.25 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C0" smd circle (at 1.25 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C1" smd circle (at 1.25 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C2" smd circle (at 1.25 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C3" smd circle (at 1.25 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C4" smd circle (at 1.25 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C5" smd circle (at 1.25 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "C6" smd circle (at 1.25 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D0" smd circle (at 2.75 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D1" smd circle (at 2.75 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D2" smd circle (at 2.75 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D3" smd circle (at 2.75 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D4" smd circle (at 2.75 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D5" smd circle (at 2.75 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "D6" smd circle (at 2.75 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E0" smd circle (at 4.25 6.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E1" smd circle (at 4.25 7.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E2" smd circle (at 4.25 8.4) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E3" smd circle (at 4.25 9.6) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E4" smd circle (at 4.25 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E5" smd circle (at 4.25 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "E6" smd circle (at 4.25 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F4" smd circle (at 5.75 10.8) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F5" smd circle (at 5.75 12.0) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F6" smd rect (at 5.75 13.2) (size 0.6 0.6) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F0" smd rect (at -2.875 4.0) (size 1.5 1.5) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F1" smd rect (at -0.625 4.0) (size 1.5 1.5) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F2" smd rect (at 1.625 4.0) (size 1.5 1.5) (layers "F.Cu" "F.Mask" "F.Paste")) - (pad "F3" smd rect (at 3.875 4.0) (size 1.5 1.5) (layers "F.Cu" "F.Mask" "F.Paste")) - (model "${KIPRJMOD}/libraries/3dmodels/BT840X_outline.step" - (offset - (xyz 0 -0.3 0.3) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz -90 0 0) - ) - ) -) diff --git a/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/XBee_Carrier_Castellated.kicad_mod b/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/XBee_Carrier_Castellated.kicad_mod new file mode 100644 index 0000000..65b020a --- /dev/null +++ b/PCB/v2.x/libraries/SnipsControllers_Custom.pretty/XBee_Carrier_Castellated.kicad_mod @@ -0,0 +1,314 @@ +(footprint "XBee_Carrier_Castellated" + (version 20241229) + (generator "pcbnew") + (generator_version "9.0") + (layer "F.Cu") + (descr "Hand-solder pads for the Snips XBee 3 carrier, a 22 x 17 mm castellated daughter board that sits flat on this side. 2.54 mm pitch; pads reach 1.7 mm past the carrier for the iron. Keep parts out of the courtyard; vias under the carrier stay tented.") + (tags "XBee castellated daughter board") + (property "Reference" "REF**" + (at 0 -11.5 0) + (layer "F.SilkS") + (hide yes) + (uuid "033c0a04-a10c-4fb4-b277-ce0c3dfb19c5") + (effects + (font + (size 0.8 0.8) + (thickness 0.12) + ) + ) + ) + (property "Value" "XBee carrier" + (at 0 0 0) + (layer "F.Fab") + (uuid "d0755590-b393-4429-81d3-c92b88e741f5") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (attr smd exclude_from_pos_files exclude_from_bom) + (fp_line + (start -11.0 -8.5) + (end 11.0 -8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "77a5ca4b-aadf-4797-8fdf-eb13bce583ee") + ) + (fp_line + (start 11.0 -8.5) + (end 11.0 6.9) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "370c7e60-68da-4fc2-aa51-99bb23b944f7") + ) + (fp_line + (start 11.0 6.9) + (end 6.1 8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "40f214be-7f50-4e73-94c7-758d65123814") + ) + (fp_line + (start 6.1 8.5) + (end -11.0 8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "558206e0-654e-44b8-9444-ed1b514d5b7d") + ) + (fp_line + (start -11.0 8.5) + (end -11.0 -8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "e188cd24-97de-439f-b2a5-fdf6de52e5c8") + ) + (fp_line + (start -11.1 -8.5) + (end -11.1 8.5) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "aba388de-ae16-45ac-9f71-75982bc56415") + ) + (fp_line + (start 11.1 -8.5) + (end 11.1 6.9) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "45383e72-c357-4ff4-8bcc-390720989918") + ) + (fp_line + (start 11.1 6.9) + (end 6.2 8.6) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "acd95282-2270-4a55-88a2-8ac6e6a96d9b") + ) + (fp_line + (start -11.25 -8.75) + (end -8.75 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "37adb262-500c-4431-a46b-23c80ae14333") + ) + (fp_line + (start -8.75 -8.75) + (end -8.75 -10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "73b50b29-847c-4679-a1af-a9414ade3c81") + ) + (fp_line + (start -8.75 -10.45) + (end 6.15 -10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "65539e50-b074-4541-850f-6f244596b1fb") + ) + (fp_line + (start 6.15 -10.45) + (end 6.15 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "0f44af8a-a5bc-498d-9f3e-c8b58abe58ac") + ) + (fp_line + (start 6.15 -8.75) + (end 11.25 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "f1a50fb8-89aa-47e3-82e4-dc1eb755045b") + ) + (fp_line + (start 11.25 -8.75) + (end 11.25 6.9) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "58fdc9ca-b773-49ca-bbbf-91266265ae73") + ) + (fp_line + (start 11.25 6.9) + (end 6.15 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "ef144003-bfa9-42cf-bbeb-0751d2208db5") + ) + (fp_line + (start 6.15 8.75) + (end 6.15 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "46c948c1-1cfb-480f-b2f9-6fd434170b9b") + ) + (fp_line + (start 6.15 8.75) + (end 6.15 10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "dd7f13bf-19b1-4f2b-bf6c-e4bdd59c84d6") + ) + (fp_line + (start 6.15 10.45) + (end -8.75 10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "31bf4638-3094-4591-bae2-cf0dd66315d7") + ) + (fp_line + (start -8.75 10.45) + (end -8.75 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "488a82bf-1a02-40ef-9096-5910c2721f5a") + ) + (fp_line + (start -8.75 8.75) + (end -11.25 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "88e24891-c515-4bfe-82c1-2649365ed690") + ) + (fp_line + (start -11.25 8.75) + (end -11.25 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "db1784ff-285c-47e1-8c34-774299faa3c3") + ) + (pad "1" smd rect + (at 5.05 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "f0314b0d-6b8e-4c7e-aee2-33542992623f") + ) + (pad "2" smd rect + (at 2.51 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "2ece2cf5-9ecd-40c7-be4f-4eaf65cbc8dc") + ) + (pad "3" smd rect + (at -0.03 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "88b54a13-ce92-46ab-9294-43119228b7cc") + ) + (pad "4" smd rect + (at -2.57 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "19731f0f-df0e-4475-b4b5-2807ac3121f3") + ) + (pad "5" smd rect + (at -5.11 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "63172451-18b6-4686-a0b9-cbb4f08fe441") + ) + (pad "6" smd rect + (at -7.65 8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "a6555361-0d1e-4b2c-aaa2-eb706c224ee1") + ) + (pad "7" smd rect + (at -7.65 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "6a3afa8d-d68a-492c-8e69-159c8d42039c") + ) + (pad "8" smd rect + (at -5.11 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "937e876d-cb56-41d3-a729-c23d0832375d") + ) + (pad "9" smd rect + (at -2.57 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "15e36e51-0c9c-4c72-9d33-c9d34ede0dbf") + ) + (pad "10" smd rect + (at -0.03 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "219e3798-d547-4314-b02e-6779fd1f4365") + ) + (pad "11" smd rect + (at 2.51 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "35ae1d9e-98f9-4b7c-a6eb-0cf22b988de3") + ) + (pad "12" smd rect + (at 5.05 -8.85) + (size 1.7 2.7) + (layers "F.Cu" "F.Mask") + (uuid "ceaf4013-cb1f-4e08-a649-a9506afc0e41") + ) +) diff --git a/PCB/v2.x/production/bom/snips_controller-bom.csv b/PCB/v2.x/production/bom/snips_controller-bom.csv index 65d2399..cb0aea3 100644 --- a/PCB/v2.x/production/bom/snips_controller-bom.csv +++ b/PCB/v2.x/production/bom/snips_controller-bom.csv @@ -1,39 +1,42 @@ -"Id";"Designator";"Footprint";"Quantity";"Designation";"Supplier and ref"; -1;"BT1";"JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal";1;"PH 2-pin battery RIGHT-ANGLE HORIZONTAL";;; -2;"C_3V3_1";"C_0603_1608Metric";1;"10µF";;; -3;"C_3V3_2, C_DBNC1, C_HALL1, C_IMU_1, C_LATCH_G1, C_OLED_2, C_RGB1, C_STICK1, C_SYS_2, C_TRIG1, C_VIN_2";"C_0402_1005Metric";11;"100nF";;; -4;"C_BAT1, C_BUCK_IN1, C_BUCK_OUT1, C_SYS_1, C_VIN_1";"C_0805_2012Metric";5;"10µF";;; -5;"C_IMU_2";"C_0603_1608Metric";1;"2.2µF";;; -6;"C_IMU_3";"C_0402_1005Metric";1;"10nF";;; -7;"C_OLED_1, C_VBUS1";"C_0603_1608Metric";2;"1µF";;; -8;"C_RF_BULK1";"C_1206_3216Metric";1;"47µF";;; -9;"D_INV_ISO1";"SOT-323_SC-70";1;"BAT54W-7-F";;; -10;"D_OR1, D_OR2";"D_SOD-123";2;"1N4148W";;; -11;"D_RGB1";"SK6812MINI-HS-012";1;"SK6812MINI-HS-012";;; -12;"D_VBUS_TVS1";"D_SOD-323";1;"TPPESD5V0S1BA";;; -13;"FB_RF1";"L_0603_1608Metric";1;"600Ω@100MHz";;; -14;"J_USB1";"USB_C_Receptacle_HRO_TYPE-C-31-M-12";1;"USB-C";;; -15;"L_BUCK1";"L_Bourns-SRN4018";1;"2.2µH";;; -16;"Q_INV1";"SOT-23";1;"MMBT3904(RANGE:100-300)";;; -17;"Q_LATCH1";"SOT-23";1;"AO3400A";;; -18;"Q_PWR1";"SOT-23";1;"AO3401A";;; -19;"R_BOOT_PU1, R_STAT1, R_STAT2, R_TS1";"R_0402_1005Metric";4;"10kΩ";;; -20;"R_BTN_PU1, R_GATE1, R_INV_BASE1, R_INV_PU1, R_PWR_EN_PD1, R_VSYS2";"R_0402_1005Metric";6;"100kΩ";;; -21;"R_CC1, R_CC2";"R_0402_1005Metric";2;"5.1kΩ";;; -22;"R_FB1";"R_0402_1005Metric";1;"255kΩ";;; -23;"R_FB2";"R_0402_1005Metric";1;"56.2kΩ";;; -24;"R_I2C_SCL1, R_I2C_SDA1";"R_0402_1005Metric";2;"4.7kΩ";;; -25;"R_ISET1";"R_0402_1005Metric";1;"604Ω";;; -26;"R_LATCH_G1";"R_0402_1005Metric";1;"1MΩ";;; -27;"R_RGB1";"R_0402_1005Metric";1;"470Ω";;; -28;"R_TRIG1";"R_0402_1005Metric";1;"1kΩ";;; -29;"R_VSET1";"R_0402_1005Metric";1;"18kΩ";;; -30;"R_VSYS1";"R_0402_1005Metric";1;"200kΩ";;; -31;"SW_BOOT1, SW_MACRO1, SW_MACRO2, SW_MACRO3, SW_MACRO4, SW_MACRO5, SW_MACRO6, SW_RST1";"SW_Alps_SKRP";8;"SKRPABE010";;; -32;"SW_PWR1, SW_THR_DN1, SW_THR_UP1, SW_TRIG_DIG1, SW_VOL_DN1, SW_VOL_UP1";"SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010";6;"SKRTLAE010";;; -33;"U_BUCK1";"SOT-23-5";1;"TLV62569DBVR";;; -34;"U_CHG1";"IC_BQ25185DLHR";1;"BQ25185DLHR";;; -35;"U_HALL1";"SOT-23";1;"DRV5055A2QDBZR";;; -36;"U_IMU1";"LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y";1;"ICM-42670-P";;; -37;"U_MCU1";"BT840XE";1;"BT840XE";;; -38;"U_OLED1";"JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal";1;"Qwiic connector";;; +Refs,Quantity,Value,Footprint,MF,MPN,LCSC,Mouser,DigiKey,Hand,DNP +"R_BTN_PU1,R_GATE1,R_INV_BASE1,R_INV_PU1,R_PWR_EN_PD1,R_VSYS2","6","100kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF1003TCE","C25741","","","","" +"C_3V3_2,C_DBNC1,C_HALL1,C_IMU_1,C_LATCH_G1,C_OLED_2,C_RGB1,C_STICK1,C_SYS_2,C_TRIG1,C_VIN_2","11","100nF","Capacitor_SMD:C_0402_1005Metric","Samsung Electro-Mechanics","CL05B104KO5NNNC","C1525","","","","" +"R_BOOT_PU1,R_EN_PU1,R_STAT1,R_STAT2,R_TS1","5","10kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF1002TCE","C25744","","","","" +"C_IMU_3","1","10nF","Capacitor_SMD:C_0402_1005Metric","Samsung Electro-Mechanics","CL05B103KB5NNNC","C15195","","","","" +"C_3V3_1","1","10µF","Capacitor_SMD:C_0603_1608Metric","Samsung Electro-Mechanics","CL10A106KP8NNNC","C19702","","","","" +"C_BAT1,C_BUCK_IN1,C_SYS_1,C_VIN_1","4","10µF","Capacitor_SMD:C_0805_2012Metric","Samsung Electro-Mechanics","CL21A106KAYNNNE","C15850","","","","" +"R_VSET1","1","18kΩ","Resistor_SMD:R_0402_1005Metric","Yageo","RC0402FR-0718KL","C138044","","","","" +"R_LATCH_G1","1","1MΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF1004TCE","C26083","","","","" +"D_OR1,D_OR2","2","1N4148W","Diode_SMD:D_SOD-123","ST(Semtech)","1N4148W","C81598","","","","" +"R_TRIG1","1","1kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF1001TCE","C11702","","","","" +"C_EN1,C_OLED_1","2","1µF","Capacitor_SMD:C_0603_1608Metric","Samsung Electro-Mechanics","CL10A105KB8NNNC","C15849","","","","" +"C_IMU_2","1","2.2µF","Capacitor_SMD:C_0603_1608Metric","Samsung Electro-Mechanics","CL10B225KP8NNNC","C100082","","","","" +"L_BUCK1","1","2.2µH","Inductor_SMD:L_Bourns-SRN4018","Bourns","SRN4018-2R2M","C913207","","","","" +"R_VSYS1","1","200kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF2003TCE","C25764","","","","" +"C_BUCK_OUT1","1","22µF","Capacitor_SMD:C_0805_2012Metric","Samsung Electro-Mechanics","CL21A226MAQNNNE","C45783","","","","" +"R_FB1","1","255kΩ","Resistor_SMD:R_0402_1005Metric","Yageo","RC0402FR-07255KL","C327361","","","","" +"R_USB_DM1,R_USB_DP1","2","27Ω","Resistor_SMD:R_0402_1005Metric","Yageo","RC0402FR-0727RL","C138021","","","","" +"C_3V3_3","1","39pF","Capacitor_SMD:C_0402_1005Metric","Yageo","CC0402JRNPO9BN390","C106223","","","","" +"R_I2C_SCL1,R_I2C_SDA1","2","4.7kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF4701TCE","C25900","","","","" +"R_RGB1","1","470Ω","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF4700TCE","C25117","","","","" +"R_CC1,R_CC2","2","5.1kΩ","Resistor_SMD:R_0402_1005Metric","UNI-ROYAL(Uniroyal Elec)","0402WGF5101TCE","C25905","","","","" +"R_FB2","1","56.2kΩ","Resistor_SMD:R_0402_1005Metric","Yageo","RC0402FR-0756K2L","C183355","","","","" +"R_ISET1","1","604Ω","Resistor_SMD:R_0402_1005Metric","Yageo","AC0402FR-07604RL","C227167","","","","" +"Q_LATCH1","1","AO3400A","Package_TO_SOT_SMD:SOT-23","Alpha & Omega Semicon","AO3400A","C20917","","","","" +"Q_PWR1","1","AO3401A","Package_TO_SOT_SMD:SOT-23","Alpha & Omega Semicon","AO3401A","C15127","","","","" +"D_INV_ISO1","1","BAT54W-7-F","Package_TO_SOT_SMD:SOT-323_SC-70","Diodes Incorporated","BAT54W-7-F","C134417","","","","" +"U_CHG1","1","BQ25185DLHR","BQ25185DLHR:IC_BQ25185DLHR","Texas Instruments","BQ25185DLHR","C19725033","","","","" +"U_HALL1","1","DRV5055A2QDBZR","Package_TO_SOT_SMD:SOT-23","Texas Instruments","DRV5055A2QDBZR","C266131","","","","" +"U_MCU1","1","ESP32-S3-MINI-1U-N8","Espressif:ESP32-S3-MINI-1U","Espressif Systems","ESP32-S3-MINI-1U-N8","C2980299","","","","" +"J_STICK1","1","GuliKit_Thumbstick","SnipsControllers_Custom:GuliKit_HallStick","GuliKit","GuliKit_Thumbstick","","","","Yes","Yes" +"U_IMU1","1","ICM-42670-P","Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y","TDK InvenSense","ICM-42670-P","C3288646","","","","" +"Q_INV1","1","MMBT3904(RANGE:100-300)","Package_TO_SOT_SMD:SOT-23","Jiangsu Changjing Electronics Technology Co., Ltd.","MMBT3904(RANGE:100-300)","C20526","","","","" +"BT1","1","PH 2-pin battery RIGHT-ANGLE HORIZONTAL","Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal","JST","S2B-PH-K(LF)(SN)","C265016","","","","" +"U_OLED1","1","Qwiic connector","Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal","JST","SM04B-SRSS-TB(LF)(SN)","C160404","","","","" +"D_RGB1","1","SK6812MINI-HS-012","SnipsControllers_Custom:SK6812MINI-HS-012","OPSCO Optoelectronics","SK6812MINI-HS","C2922787","","","","" +"SW_BOOT1,SW_MACRO1,SW_MACRO2,SW_MACRO3,SW_MACRO4,SW_MACRO5,SW_MACRO6","7","SKRPABE010","SnipsControllers_Custom:SW_Alps_SKRP","Alps Alpine","SKRPABE010","C115360","","","","" +"SW_PWR1,SW_THR_DN1,SW_THR_UP1,SW_TRIG_DIG1,SW_VOL_DN1,SW_VOL_UP1","6","SKRTLAE010","Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010","Alps Alpine","SKRTLAE010","C110293","","","","" +"U_BUCK1","1","TLV62569DBVR","Package_TO_SOT_SMD:SOT-23-5","Texas Instruments","TLV62569DBVR","C141836","","","","" +"D_VBUS_TVS1","1","TPPESD5V0S1BA","Diode_SMD:D_SOD-323","TECH PUBLIC","TPPESD5V0S1BA","C587144","","","","" +"J_USB1","1","USB-C","Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12","Hroparts Elec","TYPE-C-31-M-12","C165948","","","","" +"U_XBEE1","1","XBee carrier","SnipsControllers_Custom:XBee_Carrier_Castellated","Snips Controllers","Snips XBee carrier","","","","Yes","Yes" diff --git a/PCB/v2.x/production/gerbers/snips_controller-B_Cu.gbr b/PCB/v2.x/production/gerbers/snips_controller-B_Cu.gbr index a3a6c3e..55f9941 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-B_Cu.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-B_Cu.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Copper,L4,Bot*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -28,75 +28,84 @@ G04 Aperture macros list* 20,1,$1+$1,$4,$5,$6,$7,0* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% +%AMFreePoly0* +4,1,153,0.406581,0.754743,0.408810,0.754000,0.410000,0.754000,0.411581,0.753743,0.413810,0.753000,0.415000,0.753000,0.416581,0.752743,0.419581,0.751743,0.420236,0.751472,0.421920,0.750630,0.424581,0.749743,0.426536,0.748536,0.427964,0.747108,0.429236,0.746472,0.430536,0.745536,0.431964,0.744108,0.433236,0.743472,0.434536,0.742536,0.442536,0.734536,0.443472,0.733236, +0.444108,0.731964,0.445536,0.730536,0.446472,0.729236,0.447108,0.727964,0.448536,0.726536,0.449743,0.724581,0.450630,0.721920,0.451472,0.720236,0.451743,0.719581,0.452743,0.716581,0.453000,0.715000,0.453000,0.713810,0.453743,0.711581,0.454000,0.710000,0.454000,0.708810,0.454743,0.706581,0.455000,0.705000,0.455000,-0.705000,0.454743,-0.706581,0.454000,-0.708810, +0.454000,-0.710000,0.453743,-0.711581,0.453000,-0.713810,0.453000,-0.715000,0.452743,-0.716581,0.451743,-0.719581,0.451472,-0.720236,0.450630,-0.721920,0.449743,-0.724581,0.448536,-0.726536,0.447108,-0.727964,0.446472,-0.729236,0.445536,-0.730536,0.444108,-0.731964,0.443472,-0.733236,0.442536,-0.734536,0.434536,-0.742536,0.433236,-0.743472,0.431964,-0.744108,0.430536,-0.745536, +0.429236,-0.746472,0.427964,-0.747108,0.426536,-0.748536,0.424581,-0.749743,0.421920,-0.750630,0.420236,-0.751472,0.419581,-0.751743,0.416581,-0.752743,0.415000,-0.753000,0.413810,-0.753000,0.411581,-0.753743,0.410000,-0.754000,0.408810,-0.754000,0.406581,-0.754743,0.405000,-0.755000,-0.405000,-0.755000,-0.406581,-0.754743,-0.408810,-0.754000,-0.410000,-0.754000,-0.411581,-0.753743, +-0.413810,-0.753000,-0.415000,-0.753000,-0.416581,-0.752743,-0.419581,-0.751743,-0.420236,-0.751472,-0.421920,-0.750630,-0.424581,-0.749743,-0.426536,-0.748536,-0.427964,-0.747108,-0.429236,-0.746472,-0.430536,-0.745536,-0.431964,-0.744108,-0.433236,-0.743472,-0.434536,-0.742536,-0.442536,-0.734536,-0.443472,-0.733236,-0.444108,-0.731964,-0.445536,-0.730536,-0.446472,-0.729236,-0.447108,-0.727964, +-0.448536,-0.726536,-0.449743,-0.724581,-0.450630,-0.721920,-0.451472,-0.720236,-0.451743,-0.719581,-0.452743,-0.716581,-0.453000,-0.715000,-0.453000,-0.713810,-0.453743,-0.711581,-0.454000,-0.710000,-0.454000,-0.708810,-0.454743,-0.706581,-0.455000,-0.705000,-0.455000,0.705000,-0.454743,0.706581,-0.454000,0.708810,-0.454000,0.710000,-0.453743,0.711581,-0.453000,0.713810,-0.453000,0.715000, +-0.452743,0.716581,-0.451743,0.719581,-0.451472,0.720236,-0.450630,0.721920,-0.449743,0.724581,-0.448536,0.726536,-0.447108,0.727964,-0.446472,0.729236,-0.445536,0.730536,-0.444108,0.731964,-0.443472,0.733236,-0.442536,0.734536,-0.434536,0.742536,-0.433236,0.743472,-0.431964,0.744108,-0.430536,0.745536,-0.429236,0.746472,-0.427964,0.747108,-0.426536,0.748536,-0.424581,0.749743, +-0.421920,0.750630,-0.420236,0.751472,-0.419581,0.751743,-0.416581,0.752743,-0.415000,0.753000,-0.413810,0.753000,-0.411581,0.753743,-0.410000,0.754000,-0.408810,0.754000,-0.406581,0.754743,-0.405000,0.755000,0.405000,0.755000,0.406581,0.754743,0.406581,0.754743,$1*% G04 Aperture macros list end* %TA.AperFunction,ComponentPad*% -%ADD10C,0.300000*% +%ADD10O,1.000000X2.100000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD11O,1.000000X2.100000*% +%ADD11O,1.000000X1.600000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD12O,1.000000X1.600000*% +%ADD12C,2.550000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD13C,2.550000*% +%ADD13C,2.050000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD14C,2.050000*% -%TD*% -%TA.AperFunction,ComponentPad*% -%ADD15C,2.250000*% +%ADD14C,2.250000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD16RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD15RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD17RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% +%ADD16RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD18RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% +%ADD17RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD19RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% +%ADD18RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD20RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% +%ADD19RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD21O,1.200000X1.750000*% +%ADD20O,1.200000X1.750000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD22C,1.000000*% +%ADD21C,1.000000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD23RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% +%ADD22RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD24RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% +%ADD23RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD25RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% +%ADD24RoundRect,0.250000X-0.475000X0.250000X-0.475000X-0.250000X0.475000X-0.250000X0.475000X0.250000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD26R,1.050000X0.650000*% +%ADD25RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD27RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%ADD26RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD28RoundRect,0.218750X-0.218750X-0.256250X0.218750X-0.256250X0.218750X0.256250X-0.218750X0.256250X0*% +%ADD27RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD29RoundRect,0.087500X0.225000X0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0*% +%ADD28RoundRect,0.087500X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0.087500X0.225000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD30RoundRect,0.087500X0.087500X0.225000X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0*% +%ADD29RoundRect,0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0.225000X0.087500X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD31RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% +%ADD30RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD32RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% +%ADD31RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%TD*% +%TA.AperFunction,SMDPad,CuDef*% +%ADD32RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% %ADD33RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% @@ -110,87 +119,77 @@ G04 Aperture macros list end* %TA.AperFunction,SMDPad,CuDef*% %ADD36RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% %TD*% -%TA.AperFunction,ConnectorPad*% -%ADD37C,0.787400*% -%TD*% -%TA.AperFunction,SMDPad,CuDef*% -%ADD38RoundRect,0.225000X-0.250000X0.225000X-0.250000X-0.225000X0.250000X-0.225000X0.250000X0.225000X0*% -%TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD39RoundRect,0.225000X-0.225000X-0.375000X0.225000X-0.375000X0.225000X0.375000X-0.225000X0.375000X0*% +%ADD37RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD40R,1.250000X0.700000*% +%ADD38RoundRect,0.052000X0.198000X0.048000X-0.198000X0.048000X-0.198000X-0.048000X0.198000X-0.048000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD41C,0.600000*% +%ADD39FreePoly0,180.000000*% %TD*% -%TA.AperFunction,SMDPad,CuDef*% -%ADD42R,1.500000X1.500000*% +%TA.AperFunction,ComponentPad*% +%ADD40C,0.300000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD43R,0.600000X0.600000*% +%ADD41RoundRect,0.225000X-0.225000X-0.375000X0.225000X-0.375000X0.225000X0.375000X-0.225000X0.375000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD44RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% +%ADD42RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD45RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% +%ADD43R,1.700000X2.700000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD46RoundRect,0.250000X0.650000X-0.325000X0.650000X0.325000X-0.650000X0.325000X-0.650000X-0.325000X0*% +%ADD44RoundRect,0.150000X0.150000X-0.512500X0.150000X0.512500X-0.150000X0.512500X-0.150000X-0.512500X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD47RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% +%ADD45R,1.500000X3.600000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD48RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% +%ADD46RoundRect,0.150000X0.587500X0.150000X-0.587500X0.150000X-0.587500X-0.150000X0.587500X-0.150000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD49RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD47RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% %TD*% %TA.AperFunction,ViaPad*% -%ADD50C,0.600000*% +%ADD48C,0.600000*% %TD*% %TA.AperFunction,Conductor*% -%ADD51C,0.200000*% +%ADD49C,0.200000*% %TD*% %TA.AperFunction,Conductor*% -%ADD52C,0.400000*% +%ADD50C,0.550000*% %TD*% %TA.AperFunction,Conductor*% -%ADD53C,0.550000*% +%ADD51C,0.300000*% %TD*% %TA.AperFunction,Conductor*% -%ADD54C,0.300000*% +%ADD52C,0.400000*% +%TD*% +%TA.AperFunction,Conductor*% +%ADD53C,0.800000*% %TD*% G04 APERTURE END LIST* D10* -%TO.P,U_CHG1,12*% -%TO.N,GND*% -X129750000Y-118815000D03* -%TO.P,U_CHG1,13*% -X129750000Y-117815000D03* -%TD*% -D11* %TO.P,J_USB1,SH,SHIELD_SH*% %TO.N,GND*% X132680000Y-124020000D03* -D12* -X132680000Y-128200000D03* D11* +X132680000Y-128200000D03* +D10* X141320000Y-124020000D03* -D12* +D11* X141320000Y-128200000D03* %TD*% -D13* +D12* %TO.P,J_STICK1,*% %TO.N,*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D14* +D13* %TO.P,J_STICK1,1,X_LO_1*% %TO.N,GND*% X137500000Y-69770000D03* @@ -203,11 +202,11 @@ X135000000Y-69770000D03* %TO.N,/MCU_Core/STICK_Y*% X143730000Y-78500000D03* %TO.P,J_STICK1,3,X_HI_3*% -%TO.N,/MCU_Core/3V3_RF*% +%TO.N,3V3*% X132500000Y-69770000D03* %TO.P,J_STICK1,3',Y_HI_3'*% X143730000Y-76000000D03* -D15* +D14* %TO.P,J_STICK1,a,SW_A_a*% %TO.N,/MCU_Core/BTN_STICK*% X131750000Y-84250000D03* @@ -221,13 +220,21 @@ X131750000Y-88750000D03* %TO.N,N/C*% X138250000Y-88750000D03* %TD*% -D16* +D15* %TO.P,R_BTN_PU1,1*% %TO.N,3V3*% -X124900000Y-94600000D03* +X127381250Y-93764999D03* %TO.P,R_BTN_PU1,2*% %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X125920000Y-94600000D03* +X126361250Y-93764999D03* +%TD*% +D16* +%TO.P,C_SYS_1,1*% +%TO.N,VSYS*% +X133750000Y-94250000D03* +%TO.P,C_SYS_1,2*% +%TO.N,GND*% +X135650000Y-94250000D03* %TD*% D17* %TO.P,Q_PWR1,1,G_1*% @@ -241,14 +248,6 @@ X139235000Y-77065000D03* X138285000Y-78940000D03* %TD*% D18* -%TO.P,C_VBUS1,1*% -%TO.N,VBUS*% -X140500000Y-89525000D03* -%TO.P,C_VBUS1,2*% -%TO.N,GND*% -X140500000Y-87975000D03* -%TD*% -D19* %TO.P,D_VBUS_TVS1,1,A1_1*% %TO.N,VBUS*% X135845000Y-126245000D03* @@ -256,34 +255,50 @@ X135845000Y-126245000D03* %TO.N,GND*% X137945000Y-126245000D03* %TD*% -D20* +D19* %TO.P,BT1,1,Pin_1_1*% %TO.N,VBAT*% X145200000Y-123100000D03* -D21* +D20* %TO.P,BT1,2,Pin_2_2*% %TO.N,GND*% X147200000Y-123100000D03* %TD*% -D22* +D21* %TO.P,FID4,*% %TO.N,*% X145000000Y-61750000D03* %TD*% +D22* +%TO.P,C_VIN_2,1*% +%TO.N,VBUS*% +X125750000Y-95290000D03* +%TO.P,C_VIN_2,2*% +%TO.N,GND*% +X125750000Y-96250000D03* +%TD*% D23* -%TO.P,C_OLED_1,1*% -%TO.N,3V3*% -X123575000Y-107800000D03* -%TO.P,C_OLED_1,2*% +%TO.P,C_VIN_1,1*% +%TO.N,VBUS*% +X123750000Y-95250000D03* +%TO.P,C_VIN_1,2*% %TO.N,GND*% -X122025000Y-107800000D03* +X121850000Y-95250000D03* %TD*% -D22* +D21* %TO.P,FID6,*% %TO.N,*% X144500000Y-128250000D03* %TD*% D24* +%TO.P,C_BUCK_OUT1,1*% +%TO.N,3V3*% +X138025000Y-94800000D03* +%TO.P,C_BUCK_OUT1,2*% +%TO.N,GND*% +X138025000Y-96700000D03* +%TD*% +D25* %TO.P,D_INV_ISO1,1,A_1*% %TO.N,/Power_Control/PWR_BTN_INV_BASE*% X124661300Y-90740000D03* @@ -294,7 +309,7 @@ X125961300Y-90740000D03* %TO.N,/MCU_Core/PWR_BTN_SENSE*% X125311300Y-92515000D03* %TD*% -D25* +D26* %TO.P,D_OR1,1,K_1*% %TO.N,/Power_Control/PWR_LATCH_G*% X130135000Y-78690000D03* @@ -302,7 +317,7 @@ X130135000Y-78690000D03* %TO.N,/Power_Control/PWR_BTN_TRIGGER*% X126835000Y-78690000D03* %TD*% -D16* +D27* %TO.P,R_PWR_EN_PD1,1*% %TO.N,/Power_Buck/PWR_EN*% X140425000Y-80240000D03* @@ -310,81 +325,63 @@ X140425000Y-80240000D03* %TO.N,GND*% X141445000Y-80240000D03* %TD*% -D22* +D21* %TO.P,FID5,*% %TO.N,*% X122750000Y-128250000D03* %TD*% -D26* -%TO.P,SW_BOOT1,1*% -%TO.N,GND*% -X144100000Y-106950000D03* -X148250000Y-106950000D03* -%TO.P,SW_BOOT1,2*% -%TO.N,/MCU_Core/MCU_BOOT*% -X144100000Y-104800000D03* -X148250000Y-104800000D03* -%TD*% -D27* -%TO.P,C_TRIG1,1*% -%TO.N,/Hall_Trigger/TRIG_ADC*% -X131980000Y-91750000D03* -%TO.P,C_TRIG1,2*% -%TO.N,GND*% -X131020000Y-91750000D03* -%TD*% D28* -%TO.P,FB_RF1,1*% -%TO.N,3V3*% -X139037500Y-91375000D03* -%TO.P,FB_RF1,2*% -%TO.N,/MCU_Core/3V3_RF*% -X140612500Y-91375000D03* -%TD*% -D29* %TO.P,U_IMU1,1*% %TO.N,GND*% -X145862500Y-67050000D03* +X129062500Y-126100000D03* %TO.P,U_IMU1,2*% -X145862500Y-67550000D03* +X129562500Y-126100000D03* %TO.P,U_IMU1,3*% -X145862500Y-68050000D03* +X130062500Y-126100000D03* %TO.P,U_IMU1,4*% %TO.N,ACCEL_INT1*% -X145862500Y-68550000D03* -D30* +X130562500Y-126100000D03* +D29* %TO.P,U_IMU1,5*% %TO.N,3V3*% -X145200000Y-68712500D03* +X130725000Y-126762500D03* %TO.P,U_IMU1,6*% %TO.N,GND*% -X144700000Y-68712500D03* +X130725000Y-127262500D03* %TO.P,U_IMU1,7*% -X144200000Y-68712500D03* -D29* +X130725000Y-127762500D03* +D28* %TO.P,U_IMU1,8*% %TO.N,3V3*% -X143537500Y-68550000D03* +X130562500Y-128425000D03* %TO.P,U_IMU1,9*% %TO.N,N/C*% -X143537500Y-68050000D03* +X130062500Y-128425000D03* %TO.P,U_IMU1,10*% %TO.N,GND*% -X143537500Y-67550000D03* +X129562500Y-128425000D03* %TO.P,U_IMU1,11*% -X143537500Y-67050000D03* -D30* +X129062500Y-128425000D03* +D29* %TO.P,U_IMU1,12*% %TO.N,3V3*% -X144200000Y-66887500D03* +X128900000Y-127762500D03* %TO.P,U_IMU1,13*% %TO.N,/Accelerometer/I2C_SCL*% -X144700000Y-66887500D03* +X128900000Y-127262500D03* %TO.P,U_IMU1,14*% %TO.N,/Accelerometer/I2C_SDA*% -X145200000Y-66887500D03* +X128900000Y-126762500D03* %TD*% -D27* +D30* +%TO.P,C_BUCK_IN1,1*% +%TO.N,VSYS*% +X146500000Y-91550000D03* +%TO.P,C_BUCK_IN1,2*% +%TO.N,GND*% +X146500000Y-89650000D03* +%TD*% +D31* %TO.P,C_LATCH_G1,1*% %TO.N,GND*% X135485000Y-74890000D03* @@ -392,15 +389,15 @@ X135485000Y-74890000D03* %TO.N,/Power_Control/PWR_LATCH_G*% X134525000Y-74890000D03* %TD*% -D31* +D32* %TO.P,C_HALL1,1*% -%TO.N,/MCU_Core/3V3_RF*% -X128320000Y-64600000D03* +%TO.N,3V3*% +X128940000Y-63800000D03* %TO.P,C_HALL1,2*% %TO.N,GND*% -X129280000Y-64600000D03* +X129900000Y-63800000D03* %TD*% -D32* +D15* %TO.P,R_INV_BASE1,1*% %TO.N,VSYS*% X125881300Y-88965000D03* @@ -449,35 +446,78 @@ X135285000Y-76940000D03* %TO.N,/Power_Control/PWR_GATE*% X134335000Y-78815000D03* %TD*% -D37* -%TO.P,J_SWD1,1*% -%TO.N,3V3*% -X145665000Y-113505000D03* -%TO.P,J_SWD1,2*% -%TO.N,/MCU_Core/SWDIO*% -X146935000Y-113505000D03* -%TO.P,J_SWD1,3*% -%TO.N,/MCU_Core/MCU_RESET*% -X145665000Y-112235000D03* -%TO.P,J_SWD1,4*% -%TO.N,/MCU_Core/SWDCLK*% -X146935000Y-112235000D03* -%TO.P,J_SWD1,5*% +D22* +%TO.P,C_SYS_2,1*% +%TO.N,VSYS*% +X131250000Y-94250000D03* +%TO.P,C_SYS_2,2*% %TO.N,GND*% -X145665000Y-110965000D03* -%TO.P,J_SWD1,6*% -%TO.N,N/C*% -X146935000Y-110965000D03* +X131250000Y-95210000D03* %TD*% -D38* +D37* %TO.P,C_IMU_2,1*% %TO.N,3V3*% -X140750000Y-68475000D03* +X125475000Y-125700000D03* %TO.P,C_IMU_2,2*% %TO.N,GND*% -X140750000Y-70025000D03* +X123925000Y-125700000D03* %TD*% D16* +%TO.P,C_BAT1,1*% +%TO.N,VBAT*% +X132250000Y-97750000D03* +%TO.P,C_BAT1,2*% +%TO.N,GND*% +X134150000Y-97750000D03* +%TD*% +D38* +%TO.P,U_CHG1,1,SYS_1*% +%TO.N,VSYS*% +X129800000Y-95450000D03* +%TO.P,U_CHG1,2,BAT_2*% +%TO.N,VBAT*% +X129800000Y-95850000D03* +%TO.P,U_CHG1,3,STAT2_3*% +%TO.N,/MCU_Core/STAT2*% +X129800000Y-96250000D03* +%TO.P,U_CHG1,4,~{CE}_4*% +%TO.N,GND*% +X129800000Y-96650000D03* +%TO.P,U_CHG1,5,GND_5*% +X129800000Y-97050000D03* +%TO.P,U_CHG1,6,TS/MR_6*% +%TO.N,/Power_Charger/CHG_TS*% +X127700000Y-97050000D03* +%TO.P,U_CHG1,7,ILIM/VSET_7*% +%TO.N,/Power_Charger/CHG_VSET*% +X127700000Y-96650000D03* +%TO.P,U_CHG1,8,ISET_8*% +%TO.N,/Power_Charger/CHG_ISET*% +X127700000Y-96250000D03* +%TO.P,U_CHG1,9,STAT1_9*% +%TO.N,/MCU_Core/STAT1*% +X127700000Y-95850000D03* +%TO.P,U_CHG1,10,IN_10*% +%TO.N,VBUS*% +X127700000Y-95450000D03* +D39* +%TO.P,U_CHG1,11,THERMAL_PAD_11*% +%TO.N,GND*% +X128750000Y-96250000D03* +D40* +%TO.P,U_CHG1,12*% +X128750000Y-95750000D03* +%TO.P,U_CHG1,13*% +X128750000Y-96750000D03* +%TD*% +D27* +%TO.P,R_STAT2,1*% +%TO.N,/MCU_Core/STAT2*% +X132840000Y-100050000D03* +%TO.P,R_STAT2,2*% +%TO.N,3V3*% +X133860000Y-100050000D03* +%TD*% %TO.P,R_CC2,1*% %TO.N,/USB_C/USB_CC2*% X141265000Y-126065000D03* @@ -485,15 +525,7 @@ X141265000Y-126065000D03* %TO.N,GND*% X142285000Y-126065000D03* %TD*% -D27* -%TO.P,C_OLED_2,1*% -%TO.N,3V3*% -X123960000Y-105200000D03* -%TO.P,C_OLED_2,2*% -%TO.N,GND*% -X123000000Y-105200000D03* -%TD*% -D39* +D41* %TO.P,D_OR2,1,K_1*% %TO.N,/Power_Control/PWR_LATCH_G*% X133635000Y-72440000D03* @@ -501,7 +533,7 @@ X133635000Y-72440000D03* %TO.N,/MCU_Core/PWR_HOLD*% X136935000Y-72440000D03* %TD*% -D16* +D27* %TO.P,R_LATCH_G1,1*% %TO.N,GND*% X131775000Y-74440000D03* @@ -509,199 +541,46 @@ X131775000Y-74440000D03* %TO.N,/Power_Control/PWR_LATCH_G*% X132795000Y-74440000D03* %TD*% -D40* -%TO.P,U_MCU1,1*% -%TO.N,/Accelerometer/I2C_SDA*% -X127900000Y-101500000D03* -%TO.P,U_MCU1,2*% -%TO.N,/Accelerometer/I2C_SCL*% -X127900000Y-100400000D03* -%TO.P,U_MCU1,3*% -%TO.N,N/C*% -X127900000Y-99300000D03* -%TO.P,U_MCU1,4*% -X127900000Y-98200000D03* -%TO.P,U_MCU1,5*% -%TO.N,/MCU_Core/STICK_X*% -X127900000Y-97100000D03* -%TO.P,U_MCU1,6*% -%TO.N,/MCU_Core/STICK_Y*% -X127900000Y-96000000D03* -%TO.P,U_MCU1,7*% -%TO.N,N/C*% -X127900000Y-94900000D03* -%TO.P,U_MCU1,8*% -X127900000Y-93800000D03* -%TO.P,U_MCU1,9*% -%TO.N,/MCU_Core/3V3_RF*% -X141650000Y-93800000D03* -%TO.P,U_MCU1,10*% -%TO.N,GND*% -X141650000Y-94900000D03* -%TO.P,U_MCU1,11*% -%TO.N,/MCU_Core/PWR_BTN_SENSE*% -X141650000Y-96000000D03* -%TO.P,U_MCU1,12*% -%TO.N,/MCU_Core/MCU_BOOT*% -X141650000Y-97100000D03* -%TO.P,U_MCU1,13*% -%TO.N,/MCU_Core/RGB_DIN*% -X141650000Y-98200000D03* -%TO.P,U_MCU1,14*% -%TO.N,/MCU_Core/MCU_RESET*% -X141650000Y-99300000D03* -%TO.P,U_MCU1,15*% -%TO.N,/MCU_Core/SWDCLK*% -X141650000Y-100400000D03* -%TO.P,U_MCU1,16*% -%TO.N,/MCU_Core/SWDIO*% -X141650000Y-101500000D03* -D41* -%TO.P,U_MCU1,A0*% -%TO.N,GND*% -X132525000Y-100700000D03* -%TO.P,U_MCU1,A1*% -%TO.N,N/C*% -X132525000Y-99500000D03* -%TO.P,U_MCU1,A2*% -X132525000Y-98300000D03* -%TO.P,U_MCU1,A3*% -%TO.N,/Hall_Trigger/TRIG_ADC*% -X132525000Y-97100000D03* -%TO.P,U_MCU1,A4*% -%TO.N,/MCU_Core/VSYS_SENSE*% -X132525000Y-95900000D03* -%TO.P,U_MCU1,A5*% -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X132525000Y-94700000D03* -%TO.P,U_MCU1,A6*% -%TO.N,/Buttons_Direct/BTN_THR_UP*% -X132525000Y-93500000D03* -%TO.P,U_MCU1,B0*% -%TO.N,GND*% -X134025000Y-100700000D03* -%TO.P,U_MCU1,B1*% -%TO.N,N/C*% -X134025000Y-99500000D03* -%TO.P,U_MCU1,B2*% -X134025000Y-98300000D03* -%TO.P,U_MCU1,B3*% -X134025000Y-97100000D03* -%TO.P,U_MCU1,B4*% -X134025000Y-95900000D03* -%TO.P,U_MCU1,B5*% -X134025000Y-94700000D03* -%TO.P,U_MCU1,B6*% -%TO.N,/MCU_Core/BTN_STICK*% -X134025000Y-93500000D03* -%TO.P,U_MCU1,C0*% -%TO.N,GND*% -X135525000Y-100700000D03* -%TO.P,U_MCU1,C1*% -%TO.N,N/C*% -X135525000Y-99500000D03* -%TO.P,U_MCU1,C2*% -X135525000Y-98300000D03* -%TO.P,U_MCU1,C3*% -X135525000Y-97100000D03* -%TO.P,U_MCU1,C4*% -X135525000Y-95900000D03* -%TO.P,U_MCU1,C5*% -X135525000Y-94700000D03* -%TO.P,U_MCU1,C6*% -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X135525000Y-93500000D03* -%TO.P,U_MCU1,D0*% -%TO.N,GND*% -X137025000Y-100700000D03* -%TO.P,U_MCU1,D1*% -%TO.N,N/C*% -X137025000Y-99500000D03* -%TO.P,U_MCU1,D2*% -X137025000Y-98300000D03* -%TO.P,U_MCU1,D3*% -X137025000Y-97100000D03* -%TO.P,U_MCU1,D4*% -X137025000Y-95900000D03* -%TO.P,U_MCU1,D5*% -X137025000Y-94700000D03* -%TO.P,U_MCU1,D6*% -%TO.N,/Buttons_Direct/BTN_VOL_UP*% -X137025000Y-93500000D03* -%TO.P,U_MCU1,E0*% -%TO.N,/Buttons_Direct/BTN_MACRO5*% -X138525000Y-100700000D03* -%TO.P,U_MCU1,E1*% -%TO.N,/Buttons_Direct/BTN_MACRO6*% -X138525000Y-99500000D03* -%TO.P,U_MCU1,E2*% -%TO.N,N/C*% -X138525000Y-98300000D03* -%TO.P,U_MCU1,E3*% -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X138525000Y-97100000D03* -%TO.P,U_MCU1,E4*% -%TO.N,/MCU_Core/USB_DP*% -X138525000Y-95900000D03* -%TO.P,U_MCU1,E5*% -%TO.N,/MCU_Core/USB_DM*% -X138525000Y-94700000D03* -%TO.P,U_MCU1,E6*% -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X138525000Y-93500000D03* D42* -%TO.P,U_MCU1,F0*% +%TO.P,R_FB2,1*% +%TO.N,/Power_Buck/BUCK_FB*% +X138525000Y-100490000D03* +%TO.P,R_FB2,2*% %TO.N,GND*% -X131400000Y-102700000D03* -%TO.P,U_MCU1,F1*% -X133650000Y-102700000D03* -%TO.P,U_MCU1,F2*% -X135900000Y-102700000D03* -%TO.P,U_MCU1,F3*% -X138150000Y-102700000D03* -D41* -%TO.P,U_MCU1,F4*% -%TO.N,/MCU_Core/3V3_RF*% -X140025000Y-95900000D03* -%TO.P,U_MCU1,F5*% -%TO.N,N/C*% -X140025000Y-94700000D03* -D43* -%TO.P,U_MCU1,F6*% -%TO.N,VBUS*% -X140025000Y-93500000D03* -D41* -%TO.P,U_MCU1,Z0*% -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X131025000Y-100700000D03* -%TO.P,U_MCU1,Z1*% -%TO.N,ACCEL_INT1*% -X131025000Y-99500000D03* -%TO.P,U_MCU1,Z2*% -%TO.N,/MCU_Core/PWR_HOLD*% -X131025000Y-98300000D03* -%TO.P,U_MCU1,Z3*% -%TO.N,/MCU_Core/STAT1*% -X131025000Y-97100000D03* -%TO.P,U_MCU1,Z4*% -%TO.N,/MCU_Core/STAT2*% -X131025000Y-95900000D03* -%TO.P,U_MCU1,Z5*% -%TO.N,/Buttons_Direct/BTN_MACRO1*% -X131025000Y-94700000D03* -%TO.P,U_MCU1,Z6*% -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X131025000Y-93500000D03* +X138525000Y-101510000D03* %TD*% -D27* +D15* +%TO.P,R_VSET1,1*% +%TO.N,/Power_Charger/CHG_VSET*% +X122280000Y-99750000D03* +%TO.P,R_VSET1,2*% +%TO.N,GND*% +X121260000Y-99750000D03* +%TD*% +D31* %TO.P,C_IMU_3,1*% %TO.N,3V3*% -X145230000Y-70000000D03* +X127660000Y-128500000D03* %TO.P,C_IMU_3,2*% %TO.N,GND*% -X144270000Y-70000000D03* +X126700000Y-128500000D03* %TD*% -D16* +D15* +%TO.P,R_STAT1,1*% +%TO.N,/MCU_Core/STAT1*% +X124670000Y-97250000D03* +%TO.P,R_STAT1,2*% +%TO.N,3V3*% +X123650000Y-97250000D03* +%TD*% +%TO.P,R_ISET1,1*% +%TO.N,/Power_Charger/CHG_ISET*% +X122300000Y-98250000D03* +%TO.P,R_ISET1,2*% +%TO.N,GND*% +X121280000Y-98250000D03* +%TD*% +D27* %TO.P,R_CC1,1*% %TO.N,/USB_C/USB_CC1*% X130265000Y-123815000D03* @@ -709,98 +588,103 @@ X130265000Y-123815000D03* %TO.N,GND*% X131285000Y-123815000D03* %TD*% -D44* -%TO.P,C_3V3_2,1*% -%TO.N,/MCU_Core/3V3_RF*% -X144555000Y-95985000D03* -%TO.P,C_3V3_2,2*% -%TO.N,GND*% -X144555000Y-95025000D03* -%TD*% -D45* -%TO.P,C_3V3_1,1*% -%TO.N,/MCU_Core/3V3_RF*% -X142300000Y-91375000D03* -%TO.P,C_3V3_1,2*% -%TO.N,GND*% -X143850000Y-91375000D03* -%TD*% -D16* -%TO.P,R_VSYS1,1*% -%TO.N,VSYS*% -X133265000Y-91615000D03* -%TO.P,R_VSYS1,2*% -%TO.N,/MCU_Core/VSYS_SENSE*% -X134285000Y-91615000D03* -%TD*% -D46* -%TO.P,C_RF_BULK1,1*% -%TO.N,/MCU_Core/3V3_RF*% -X146495000Y-96870000D03* -%TO.P,C_RF_BULK1,2*% -%TO.N,GND*% -X146495000Y-93920000D03* -%TD*% D36* -%TO.P,R_I2C_SDA1,1*% +%TO.P,R_FB1,1*% +%TO.N,/Power_Buck/BUCK_FB*% +X138525000Y-99510000D03* +%TO.P,R_FB1,2*% %TO.N,3V3*% -X125875000Y-103010000D03* -%TO.P,R_I2C_SDA1,2*% -%TO.N,/Accelerometer/I2C_SDA*% -X125875000Y-101990000D03* +X138525000Y-98490000D03* %TD*% -%TO.P,R_I2C_SCL1,1*% +D43* +%TO.P,U_XBEE1,1*% +%TO.N,/XBee/XBEE_CTS*% +X126450000Y-121300000D03* +%TO.P,U_XBEE1,2*% +%TO.N,/XBee/XBEE_DIN*% +X128990000Y-121300000D03* +%TO.P,U_XBEE1,3*% +%TO.N,/XBee/XBEE_DOUT*% +X131530000Y-121300000D03* +%TO.P,U_XBEE1,4*% +%TO.N,/XBee/XBEE_RTS*% +X134070000Y-121300000D03* +%TO.P,U_XBEE1,5*% +%TO.N,/XBee/XBEE_ON_SLEEP*% +X136610000Y-121300000D03* +%TO.P,U_XBEE1,6*% +%TO.N,/XBee/XBEE_RESET*% +X139150000Y-121300000D03* +%TO.P,U_XBEE1,7*% +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X139150000Y-103600000D03* +%TO.P,U_XBEE1,8*% +%TO.N,GND*% +X136610000Y-103600000D03* +%TO.P,U_XBEE1,9*% %TO.N,3V3*% -X125875000Y-100760000D03* -%TO.P,R_I2C_SCL1,2*% -%TO.N,/Accelerometer/I2C_SCL*% -X125875000Y-99740000D03* +X134070000Y-103600000D03* +%TO.P,U_XBEE1,10*% +X131530000Y-103600000D03* +%TO.P,U_XBEE1,11*% +%TO.N,GND*% +X128990000Y-103600000D03* +%TO.P,U_XBEE1,12*% +X126450000Y-103600000D03* %TD*% -D26* -%TO.P,SW_RST1,1*% +D44* +%TO.P,U_BUCK1,1,EN_1*% +%TO.N,/Power_Buck/PWR_EN*% +X148425000Y-95750000D03* +%TO.P,U_BUCK1,2,GND_2*% %TO.N,GND*% -X144100000Y-102850000D03* -X148250000Y-102850000D03* -%TO.P,SW_RST1,2*% -%TO.N,/MCU_Core/MCU_RESET*% -X144100000Y-100700000D03* -X148250000Y-100700000D03* +X147475000Y-95750000D03* +%TO.P,U_BUCK1,3,SW_3*% +%TO.N,/Power_Buck/BUCK_SW*% +X146525000Y-95750000D03* +%TO.P,U_BUCK1,4,VIN_4*% +%TO.N,VSYS*% +X146525000Y-93475000D03* +%TO.P,U_BUCK1,5,FB_5*% +%TO.N,/Power_Buck/BUCK_FB*% +X148425000Y-93475000D03* %TD*% -D47* +D32* %TO.P,C_IMU_1,1*% %TO.N,3V3*% -X142250000Y-68520000D03* +X126720000Y-125900000D03* %TO.P,C_IMU_1,2*% %TO.N,GND*% -X142250000Y-69480000D03* +X127680000Y-125900000D03* %TD*% -D16* -%TO.P,R_VSYS2,1*% -%TO.N,/MCU_Core/VSYS_SENSE*% -X135515000Y-91615000D03* -%TO.P,R_VSYS2,2*% -%TO.N,GND*% -X136535000Y-91615000D03* +D45* +%TO.P,L_BUCK1,1,1_1*% +%TO.N,/Power_Buck/BUCK_SW*% +X144050000Y-95750000D03* +%TO.P,L_BUCK1,2,2_2*% +%TO.N,3V3*% +X141000000Y-95750000D03* %TD*% -D44* +D22* %TO.P,C_STICK1,1*% -%TO.N,/MCU_Core/3V3_RF*% -X145505000Y-76685000D03* +%TO.N,3V3*% +X145505000Y-75725000D03* %TO.P,C_STICK1,2*% %TO.N,GND*% -X145505000Y-75725000D03* +X145505000Y-76685000D03* %TD*% -D48* +D46* %TO.P,U_HALL1,1*% -%TO.N,/MCU_Core/3V3_RF*% -X127625000Y-67950000D03* +%TO.N,3V3*% +X127437500Y-63800000D03* %TO.P,U_HALL1,2*% %TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127625000Y-66050000D03* +X127437500Y-65700000D03* %TO.P,U_HALL1,3*% %TO.N,GND*% -X129500000Y-67000000D03* +X125562500Y-64750000D03* %TD*% +D47* %TO.P,Q_INV1,1,B_1*% %TO.N,/Power_Control/PWR_BTN_INV_BASE*% X124061300Y-86915000D03* @@ -811,7 +695,7 @@ X124061300Y-85015000D03* %TO.N,/Power_Control/PWR_BTN_TRIGGER*% X125936300Y-85965000D03* %TD*% -D49* +D42* %TO.P,R_TRIG1,1*% %TO.N,/Hall_Trigger/TRIG_ANALOG*% X129750000Y-90740000D03* @@ -819,1229 +703,1171 @@ X129750000Y-90740000D03* %TO.N,/Hall_Trigger/TRIG_ADC*% X129750000Y-91760000D03* %TD*% -D36* -%TO.P,R_BOOT_PU1,1*% -%TO.N,/MCU_Core/MCU_BOOT*% -X144565000Y-99285000D03* -%TO.P,R_BOOT_PU1,2*% -%TO.N,3V3*% -X144565000Y-98265000D03* +D15* +%TO.P,R_TS1,1*% +%TO.N,/Power_Charger/CHG_TS*% +X122280000Y-101250000D03* +%TO.P,R_TS1,2*% +%TO.N,GND*% +X121260000Y-101250000D03* %TD*% -D50* -%TO.N,VSYS*% -X131134999Y-72039999D03* -X133551500Y-90667500D03* -X131197200Y-105109200D03* -X135775300Y-108336200D03* -X127561250Y-90824999D03* +D48* +%TO.N,3V3*% +X127761250Y-93014999D03* +X145311599Y-107614004D03* +X136012023Y-99792121D03* +X131100000Y-101100000D03* +X132248535Y-126920005D03* +X127200000Y-127762500D03* +X124950000Y-104123528D03* +X134200000Y-106400000D03* +X125080000Y-124896016D03* +X123900000Y-98100000D03* +X141068110Y-104176936D03* +X130620864Y-129450000D03* +X129000000Y-64600000D03* +X126320000Y-106400000D03* +X145500000Y-117780000D03* +X138500000Y-93250000D03* +X137400000Y-100200000D03* %TO.N,GND*% -X144000000Y-94500000D03* -X131800000Y-124350000D03* -X130449999Y-67550000D03* -X143750000Y-70550000D03* -X123950000Y-83200000D03* -X121300000Y-107150000D03* -X142800000Y-95850000D03* -X139100000Y-103700000D03* -X122350000Y-105150000D03* -X131800000Y-96500000D03* -X136300000Y-95300000D03* -X121750000Y-119315000D03* -X122600000Y-125750000D03* -X128750000Y-124300000D03* -X123150000Y-85600000D03* -X123050000Y-95850000D03* -X140500000Y-108600000D03* -X128750000Y-103050000D03* -X122600000Y-124650000D03* -X146500000Y-67450000D03* -X135250000Y-106825000D03* -X140800000Y-122150000D03* -X142850000Y-95000000D03* -X136250000Y-117315000D03* -X134600000Y-103700000D03* -X130500000Y-92300000D03* -X129870634Y-119615000D03* -X131450000Y-117565000D03* -X145300000Y-75100000D03* -X136400000Y-100400000D03* -X140000000Y-69400000D03* -X134700000Y-63950000D03* -X135450000Y-103800000D03* -X137850000Y-104150000D03* -X133000000Y-119265000D03* -X129000000Y-96550000D03* -X148500000Y-83050000D03* +X140600000Y-118700000D03* +X126900000Y-123500000D03* +X128300000Y-97700000D03* +X128700000Y-100300000D03* +X139600000Y-114100000D03* +X130850000Y-97425000D03* +X130700000Y-63800000D03* +X139100000Y-70700000D03* +X132500000Y-67000000D03* +X145400000Y-88100000D03* +X137500000Y-97750000D03* +X135250000Y-97250000D03* +X124200000Y-71800000D03* +X134900000Y-64600000D03* +X147050000Y-96950000D03* +X146248528Y-83299999D03* +X124200000Y-64800000D03* +X145600000Y-73000000D03* +X124750000Y-96250000D03* +X131300000Y-117800000D03* +X130800000Y-106700000D03* +X122600000Y-104000000D03* +X142000000Y-114200000D03* +X124100000Y-83700000D03* +X140400000Y-100300000D03* +X121800000Y-96700000D03* +X137799998Y-103000000D03* +X135250000Y-95750000D03* X136285000Y-75940000D03* -X144550000Y-69350000D03* -X143300000Y-102350000D03* -X143200000Y-90650000D03* -X132150000Y-104150000D03* -X130449999Y-103700000D03* -X141700000Y-70000000D03* -X137400000Y-125800000D03* -X123950000Y-73200000D03* -X137450000Y-114300000D03* -X129770634Y-116815000D03* -X131900000Y-100400000D03* -X144950000Y-110700000D03* -X148500000Y-73050000D03* -X143300000Y-106450000D03* -X137050000Y-92150000D03* +X131800000Y-100500000D03* +X128349799Y-95084604D03* +X132000000Y-95300000D03* X131785000Y-73440000D03* -X142800000Y-103050000D03* -X136050000Y-101250000D03* -X141950000Y-79700000D03* -X129800000Y-64050000D03* -X139850000Y-87250000D03* -X145350000Y-93100000D03* -X130950000Y-107800000D03* -X142800000Y-126600000D03* -X146350000Y-66599999D03* -X145450000Y-95800000D03* -X134550000Y-101250000D03* -X147450000Y-106450000D03* -X123050000Y-103050000D03* -X136250000Y-118815000D03* -X147450000Y-102350000D03* -X142900000Y-67400000D03* -X145400000Y-103050000D03* -X123000000Y-104550000D03* -X133199999Y-122150000D03* -X130400000Y-126300000D03* -X125750000Y-118315000D03* -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X129800000Y-100700000D03* -%TO.N,VBUS*% -X125770000Y-125525300D03* -X134650000Y-121702500D03* -X139450000Y-121868900D03* -X141321300Y-92762500D03* -X141703000Y-89578400D03* -X149218700Y-96601800D03* -%TO.N,3V3*% -X131950000Y-112300000D03* -X127300000Y-121550001D03* -X123900000Y-113658400D03* -X146120300Y-98555000D03* -X124549200Y-107406100D03* -X123860000Y-116915000D03* -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X131797000Y-95119100D03* +X122500000Y-125200000D03* +%TO.N,/MCU_Core/MCU_BOOT*% +X139900000Y-106400000D03* +X144900000Y-108300000D03* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X130070634Y-92600000D03* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X124754600Y-83434100D03* -X132620800Y-86688200D03* +X121873930Y-107063387D03* +X130300000Y-116600000D03* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X139209300Y-100184300D03* -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X139789800Y-98443100D03* +X141300000Y-106600000D03* +X142600000Y-102400000D03* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X129065000Y-94095500D03* -%TO.N,VBAT*% -X133810600Y-118937400D03* -%TO.N,/MCU_Core/STAT2*% -X130387500Y-96500000D03* -%TO.N,/MCU_Core/STAT1*% -X123374265Y-117590735D03* +X128200000Y-105450002D03* +X130400000Y-109900000D03* %TO.N,/Accelerometer/I2C_SDA*% -X132254800Y-65652100D03* -X124959600Y-104749000D03* +X124200000Y-111600000D03* +X124600000Y-109800000D03* +X121874741Y-124680758D03* %TO.N,/Accelerometer/I2C_SCL*% -X121327800Y-96462500D03* -X126003900Y-70995100D03* -X126735300Y-100400000D03* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X145804700Y-84769200D03* -%TO.N,/USB_C/USB_CC1*% -X135750000Y-121500900D03* -%TO.N,/MCU_Core/USB_DP*% -X148072200Y-111842500D03* -X139484600Y-96501700D03* -%TO.N,/MCU_Core/USB_DM*% -X137901700Y-95241600D03* -%TO.N,/USB_C/USB_CC2*% -X138750000Y-126065000D03* -%TO.N,/MCU_Core/STICK_X*% -X126670100Y-93676600D03* -%TO.N,/MCU_Core/STICK_Y*% -X130207300Y-95609600D03* -%TO.N,/MCU_Core/3V3_RF*% -X142999700Y-92385900D03* +X125800000Y-109700000D03* +X122700000Y-114100000D03* +X121100000Y-124880210D03* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X138900000Y-106200000D03* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X133300000Y-100800000D03* +X133100000Y-107000000D03* +X136161765Y-101138235D03* +%TO.N,/MCU_Core/STAT2*% +X130824265Y-108075735D03* +%TO.N,/MCU_Core/STAT1*% +X130800000Y-108900000D03* +X127500000Y-99000000D03* +X126150000Y-97470100D03* %TO.N,/MCU_Core/BTN_STICK*% -X134709100Y-92787200D03* +X130500000Y-110800000D03* +X126600000Y-100400000D03* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X145452900Y-98045000D03* -X120688600Y-97070100D03* +X120600000Y-125765642D03* +X130500000Y-114200000D03* +X124000000Y-119600000D03* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X131000000Y-62700000D03* +X122300000Y-87800000D03* +X131700000Y-115100000D03* +X124500000Y-67800000D03* +X121893900Y-106234827D03* +%TO.N,/XBee/XBEE_CTS*% +X127800000Y-117800000D03* %TO.N,/MCU_Core/RGB_DIN*% -X129216700Y-123115100D03* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X123557800Y-90439600D03* -%TO.N,/Buttons_Direct/BTN_VOL_UP*% -X135734500Y-92661400D03* -%TO.N,/Power_Buck/PWR_EN*% -X145850800Y-107623700D03* -X145980700Y-85815700D03* -X141116700Y-110981600D03* -%TO.N,/Buttons_Direct/BTN_MACRO5*% -X136150000Y-104250000D03* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X127525700Y-92504700D03* -X129861700Y-101982200D03* +X126002198Y-123340339D03* +X130400000Y-117400000D03* +%TO.N,/XBee/XBEE_DIN*% +X130179998Y-120689999D03* +%TO.N,/XBee/XBEE_DOUT*% +X131615136Y-118535318D03* %TO.N,ACCEL_INT1*% -X129871400Y-99693700D03* -X139636800Y-97508700D03* -X147014800Y-76170200D03* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X134775000Y-95096400D03* -X135000000Y-61269100D03* -X134105300Y-87305100D03* +X139400000Y-116900000D03* +%TO.N,/Buttons_Direct/BTN_VOL_UP*% +X147034358Y-98156239D03* +X133000000Y-118200000D03* +%TO.N,/XBee/XBEE_RTS*% +X133900000Y-118200000D03* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147700000Y-98600000D03* +X134700000Y-117700000D03* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135600000Y-118300000D03* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-118300000D03* %TO.N,/MCU_Core/PWR_HOLD*% +X140950000Y-90700000D03* X138485000Y-72539999D03* -X129625000Y-98237500D03* -%TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127260700Y-66852300D03* -X126692500Y-80628700D03* -%TD*% +X142000000Y-107300000D03* +%TO.N,VBUS*% +X123750000Y-95250000D03* +X137000000Y-124900000D03* +X122300000Y-102800000D03* +%TO.N,/USB_C/USB_CC1*% +X129200000Y-123700000D03* +%TO.N,/USB_C/USB_CC2*% +X142300000Y-124900000D03* %TO.N,VSYS*% +X129700000Y-93350000D03* +X142100000Y-79300000D03* +X144800000Y-90650000D03* +X144600000Y-86300000D03* +%TO.N,VBAT*% +X135900000Y-99000000D03* +X147300000Y-109300000D03* +%TO.N,/Power_Buck/BUCK_FB*% +X139885887Y-98225129D03* +X139500000Y-94850000D03* +%TD*% +%TO.N,3V3*% +D49* +X131637500Y-126862500D02* +X131537500Y-126762500D01* +X125121016Y-125346016D02* +X125475000Y-125700000D01* +X132248535Y-126920005D02* +X131965690Y-126920005D01* +D50* +X139500000Y-95750000D02* +X138975000Y-95750000D01* +D49* +X138110000Y-98490000D02* +X138525000Y-98490000D01* +D50* +X139500000Y-95750000D02* +X139500000Y-97515000D01* +D49* +X127200000Y-127762500D02* +X128900000Y-127762500D01* +X137400000Y-100200000D02* +X137400000Y-99200000D01* +X123650000Y-97850000D02* +X123900000Y-98100000D01* +X135107879Y-99792121D02* +X134850000Y-100050000D01* +X144005000Y-75725000D02* +X143730000Y-76000000D01* +X130562500Y-129391636D02* +X130620864Y-129450000D01* +X128940000Y-64540000D02* +X129000000Y-64600000D01* +D50* +X138025000Y-94800000D02* +X138025000Y-93725000D01* +D49* +X127437500Y-63800000D02* +X128940000Y-63800000D01* +X131965690Y-126920005D02* +X131908185Y-126862500D01* +X127660000Y-128500000D02* +X127660000Y-128222500D01* +X128940000Y-63800000D02* +X128940000Y-64540000D01* +D50* +X138975000Y-95750000D02* +X138025000Y-94800000D01* +D49* +X134850000Y-100050000D02* +X133860000Y-100050000D01* +X125121016Y-124937032D02* +X125121016Y-125346016D01* +X131260000Y-101100000D02* +X131530000Y-101370000D01* +X134070000Y-106270000D02* +X134200000Y-106400000D01* +X126720000Y-125900000D02* +X125675000Y-125900000D01* +X130562500Y-128425000D02* +X130562500Y-129391636D01* +X127660000Y-128222500D02* +X127200000Y-127762500D01* +X131908185Y-126862500D02* +X131637500Y-126862500D01* +X131100000Y-101100000D02* +X131260000Y-101100000D01* +X131537500Y-126762500D02* +X130725000Y-126762500D01* +X127381250Y-93395000D02* +X127761250Y-93014999D01* +X131530000Y-101370000D02* +X131530000Y-103600000D01* +D50* +X139500000Y-97515000D02* +X138525000Y-98490000D01* +D49* +X136012023Y-99792121D02* +X135107879Y-99792121D01* +D50* +X138025000Y-93725000D02* +X138500000Y-93250000D01* +X141000000Y-95750000D02* +X139500000Y-95750000D01* +D49* +X145505000Y-75725000D02* +X144005000Y-75725000D01* +X134070000Y-103600000D02* +X134070000Y-106270000D01* +X127381250Y-93764999D02* +X127381250Y-93395000D01* +X123650000Y-97250000D02* +X123650000Y-97850000D01* +X134070000Y-103370000D02* +X134070000Y-103600000D01* +X125080000Y-124896016D02* +X125121016Y-124937032D01* +X137400000Y-99200000D02* +X138110000Y-98490000D01* +%TO.N,GND*% D51* -X141405000Y-76340000D02* -X140785000Y-76960000D01* -X131334999Y-71539999D02* -X134083696Y-71539999D01* -D52* -X135775300Y-108336200D02* -X134424200Y-108336200D01* +X138025000Y-97225000D02* +X137500000Y-97750000D01* +D49* +X130450000Y-96700000D02* +X130400000Y-96650000D01* +X142285000Y-127235000D02* +X141320000Y-128200000D01* +X132475000Y-123815000D02* +X132680000Y-124020000D01* +X130775000Y-97425000D02* +X130400000Y-97050000D01* +X130062500Y-125492124D02* +X130062500Y-126100000D01* +X137945000Y-126245000D02* +X139365000Y-126245000D01* D51* -X139235000Y-77065000D02* -X140680000Y-77065000D01* -D52* -X125881000Y-89055000D02* -X125881300Y-89054700D01* +X132000000Y-95300000D02* +X131720000Y-95220000D01* +D49* +X129015000Y-129110000D02* +X129062500Y-129062500D01* D51* -X141153924Y-75370000D02* -X141405000Y-75621075D01* -X137913696Y-75370000D02* -X141153924Y-75370000D01* -D53* -X140680000Y-77065000D02* -X140785000Y-76960000D01* +X134150000Y-97750000D02* +X134750000Y-97750000D01* +D49* +X130062500Y-126937500D02* +X130062500Y-126962932D01* +X129562500Y-126437500D02* +X130062500Y-126937500D01* +X128750000Y-96250000D02* +X128886397Y-96250000D01* +X129650000Y-125350000D02* +X129350000Y-125350000D01* D51* -X134083696Y-71539999D02* -X134484348Y-71940652D01* -X134484348Y-71940652D02* -X137913696Y-75370000D01* -D52* -X133265000Y-91615000D02* -X133265000Y-90954000D01* +X134750000Y-97750000D02* +X135250000Y-97250000D01* +D49* +X129200000Y-97320634D02* +X129200000Y-96563603D01* +X142285000Y-126065000D02* +X142285000Y-127235000D01* +X129562500Y-128062068D02* +X129862068Y-127762500D01* +X123000000Y-125700000D02* +X123925000Y-125700000D01* D51* -X127561250Y-90824999D02* -X128461250Y-91725000D01* -X131334999Y-71840000D02* -X131134999Y-72039999D01* -D52* -X133265000Y-90954000D02* -X133551500Y-90667500D01* -X125881300Y-89054700D02* -X125881300Y-88965000D01* +X139240000Y-101510000D02* +X139500000Y-101250000D01* +D49* +X126700000Y-128500000D02* +X127310000Y-129110000D01* +X121260000Y-99750000D02* +X121260000Y-101250000D01* +X130725000Y-127262500D02* +X131742500Y-127262500D01* +X141445000Y-80240000D02* +X142970000Y-80240000D01* +X128700000Y-101224998D02* +X128990000Y-101514998D01* +X121280000Y-97220000D02* +X121280000Y-98250000D01* +X130725000Y-127762500D02* +X132242500Y-127762500D01* +X121280000Y-98250000D02* +X121280000Y-99730000D01* +X128424998Y-100300000D02* +X126450000Y-102274998D01* +X124250000Y-64750000D02* +X124200000Y-64800000D01* +X121800000Y-96700000D02* +X121280000Y-97220000D01* +X128820634Y-97700000D02* +X129200000Y-97320634D01* +X131285000Y-123815000D02* +X132475000Y-123815000D01* +X129920376Y-125350000D02* +X130062500Y-125492124D01* +X145505000Y-79225000D02* +X143730000Y-81000000D01* +X130850000Y-97425000D02* +X130775000Y-97425000D01* +X132580000Y-128300000D02* +X132680000Y-128200000D01* +X129200000Y-129200000D02* +X129562500Y-128837500D01* +X129200000Y-96563603D02* +X128886397Y-96250000D01* +X130850000Y-97425000D02* +X130450000Y-97025000D01* +X128700000Y-100300000D02* +X128424998Y-100300000D01* +X132500000Y-67000000D02* +X134900000Y-64600000D01* +X130062500Y-126962932D02* +X130362068Y-127262500D01* +X124061250Y-85015000D02* +X124061250Y-84414999D01* +X125562500Y-64750000D02* +X124250000Y-64750000D01* D51* -X141405000Y-75621075D02* -X141405000Y-76340000D01* -D52* -X134424200Y-108336200D02* -X131197200Y-105109200D01* +X138025000Y-96700000D02* +X138025000Y-97225000D01* +D49* +X129200000Y-95379366D02* +X129200000Y-95936397D01* +X130362068Y-127262500D02* +X130725000Y-127262500D01* D51* -X125881250Y-89145000D02* -X127561250Y-90824999D01* -X125881250Y-88965000D02* -X125881250Y-89145000D01* -X131334999Y-71539999D02* -X131334999Y-71840000D01* -D52* -X128461300Y-91725000D02* -X128461000Y-91725000D01* -%TO.N,GND*% +X139500000Y-101250000D02* +X139500000Y-101200000D01* +D49* +X129650000Y-125350000D02* +X129920376Y-125350000D01* +X128300000Y-97700000D02* +X128820634Y-97700000D01* +X135485000Y-74889999D02* +X135485000Y-75139999D01* +X129062500Y-128425000D02* +X129062500Y-129062500D01* +X129350000Y-125350000D02* +X129062500Y-125637500D01* D51* -X145505000Y-75630000D02* -X145505000Y-75725000D01* -X136800000Y-91900000D02* -X137050000Y-92150000D01* -X143250000Y-67400000D02* -X142900000Y-67400000D01* -X141700000Y-79950000D02* -X141950000Y-79700000D01* -X137625000Y-125925000D02* -X137945000Y-126245000D01* -X147750000Y-106650000D02* -X147650000Y-106650000D01* -X132225000Y-100400000D02* -X132525000Y-100700000D01* -X141825000Y-79825000D02* -X141825000Y-80240000D01* -X134350000Y-103450000D02* -X134600000Y-103700000D01* -X121600000Y-107350000D02* -X121500000Y-107350000D01* -X122750000Y-104800000D02* -X123000000Y-104550000D01* -X144150000Y-94650000D02* -X144180000Y-94650000D01* -X143850000Y-91325000D02* -X143850000Y-91375000D01* -X147950000Y-102550000D02* -X148250000Y-102850000D01* -X146162500Y-66750000D02* -X145862500Y-67050000D01* -X134350000Y-103450000D02* -X133650000Y-102750000D01* -X135800000Y-101000000D02* -X136050000Y-101250000D01* -X144300000Y-94800000D02* -X144000000Y-94500000D01* -X146050000Y-66900000D02* -X146350000Y-66599999D01* -X145200000Y-75200000D02* -X145300000Y-75100000D01* -X145200000Y-75450000D02* -X145200000Y-75200000D01* -X130750000Y-92050000D02* -X130500000Y-92300000D01* -X143400000Y-90875000D02* -X143850000Y-91325000D01* -X143800000Y-106650000D02* -X144100000Y-106950000D01* -X140050000Y-87550000D02* -X140050000Y-87450000D01* -X123350000Y-85400000D02* -X123150000Y-85600000D01* -X143250000Y-67250000D02* -X143337500Y-67250000D01* -X122750000Y-104900000D02* -X122750000Y-104800000D01* -X142000000Y-94550000D02* -X141650000Y-94900000D01* -X129925000Y-67425000D02* -X129500000Y-67000000D01* -X147650000Y-102550000D02* -X147450000Y-102350000D01* -X135000000Y-63475000D02* -X135000000Y-62700000D01* -X122350000Y-105150000D02* -X122950000Y-105150000D01* -X143400000Y-90900000D02* -X143400000Y-90850000D01* -X122950000Y-105150000D02* -X123000000Y-105200000D01* -X144000000Y-70300000D02* -X143750000Y-70550000D01* -X130699999Y-103450000D02* -X130449999Y-103700000D01* -X138850000Y-103450000D02* -X138150000Y-102750000D01* -X147750000Y-102550000D02* -X147650000Y-102550000D01* -X145300000Y-110600000D02* -X145665000Y-110965000D01* -X131550000Y-124100000D02* -X131285000Y-123835000D01* -X124061300Y-85015000D02* -X124061000Y-85015000D01* -X147650000Y-106650000D02* -X147450000Y-106450000D01* -X143250000Y-67400000D02* -X143387500Y-67400000D01* -X135200000Y-103450000D02* -X135200000Y-103550000D01* -X140500000Y-87950000D02* -X140500000Y-87975000D01* -X147950000Y-106650000D02* -X148250000Y-106950000D01* -X123350000Y-85300000D02* -X123350000Y-85400000D01* -X144450000Y-69075000D02* -X144450000Y-68950000D01* -X145862500Y-67550000D02* -X145862600Y-67550000D01* -X135200000Y-103550000D02* -X135450000Y-103800000D01* -X141445000Y-80240000D02* -X141834999Y-80240000D01* -X144350000Y-68850000D02* -X144450000Y-68950000D01* -X145862600Y-67550000D02* -X146156300Y-67843700D01* -X123350000Y-85350000D02* -X123726000Y-85350000D01* -X135485000Y-75139999D02* -X136285000Y-75940000D01* -X144400000Y-68900000D02* -X144387500Y-68900000D01* -X145300000Y-110600000D02* -X145050000Y-110600000D01* -X143150000Y-67400000D02* -X143250000Y-67300000D01* -X146200000Y-66750000D02* -X146162500Y-66750000D01* -X141825000Y-69875000D02* -X141855000Y-69875000D01* -X131400000Y-102750000D02* -X131400000Y-102700000D01* -X145800000Y-93225000D02* -X146495000Y-93920000D01* -X146128200Y-67871800D02* -X146040700Y-67871800D01* -X134700000Y-63600000D02* -X134700000Y-63950000D01* -X129280000Y-64570000D02* -X129280000Y-64600000D01* -X142400000Y-94550000D02* -X142850000Y-95000000D01* -X138150000Y-102750000D02* -X138150000Y-102700000D01* -X136535000Y-91635000D02* -X136535000Y-91615000D01* -X144200000Y-68712500D02* -X144700000Y-68712500D01* -X130325000Y-67425000D02* -X129925000Y-67425000D01* +X147475000Y-96525000D02* +X147050000Y-96950000D01* +X129900000Y-63800000D02* +X130700000Y-63800000D01* +D49* +X139365000Y-126245000D02* +X141320000Y-128200000D01* +D51* +X139500000Y-101200000D02* +X140400000Y-100300000D01* +D49* +X130062500Y-126100000D02* +X130062500Y-126937500D01* +X124100000Y-84376249D02* +X124061250Y-84414999D01* +D51* +X131720000Y-95220000D02* +X131250000Y-95220000D01* +D49* +X145505000Y-76685000D02* +X145505000Y-79225000D01* +X127310000Y-129110000D02* +X129015000Y-129110000D01* +X134900000Y-64600000D02* +X134900000Y-62800000D01* +X121850000Y-96650000D02* +X121800000Y-96700000D01* +X128360000Y-126100000D02* +X128160000Y-125900000D01* +X130450000Y-97025000D02* +X130450000Y-96700000D01* +X142970000Y-80240000D02* +X143730000Y-81000000D01* +X147200000Y-96950000D02* +X147050000Y-96950000D01* X131774999Y-73449999D02* X131785000Y-73440000D01* -X136725000Y-100400000D02* -X137025000Y-100700000D01* -X143500000Y-102550000D02* -X143300000Y-102350000D01* -X145050000Y-110600000D02* -X144950000Y-110700000D01* -X145600000Y-93350000D02* -X145350000Y-93100000D01* -X131774999Y-74440000D02* -X131774999Y-73449999D01* -X135525000Y-100725000D02* -X135525000Y-100700000D01* -X132250000Y-100400000D02* -X131900000Y-100400000D01* -X147750000Y-106650000D02* -X147950000Y-106650000D01* -X138850000Y-103450000D02* -X139100000Y-103700000D01* -X136750000Y-100400000D02* -X136400000Y-100400000D01* -X131285000Y-123835000D02* -X131285000Y-123815000D01* -X146100000Y-67900000D02* -X146450000Y-67550000D01* -X143400000Y-90850000D02* -X143200000Y-90650000D01* -X141950000Y-69750000D02* -X141700000Y-70000000D01* -X137525000Y-125925000D02* -X137625000Y-125925000D01* -X143600000Y-102550000D02* -X143800000Y-102550000D01* -X121500000Y-107350000D02* -X121300000Y-107150000D01* -X146012500Y-67400000D02* -X145862500Y-67550000D01* -X147750000Y-102550000D02* -X147950000Y-102550000D01* -X142250000Y-94550000D02* -X142400000Y-94550000D01* -X140050000Y-87450000D02* -X139850000Y-87250000D01* -X144550000Y-69175000D02* -X144450000Y-69075000D01* -X145200000Y-75325000D02* -X145505000Y-75630000D01* -X142285000Y-126085000D02* -X142285000Y-126065000D01* -X130750000Y-92050000D02* -X131020000Y-91780000D01* -X140300000Y-69600000D02* -X140200000Y-69600000D01* -X143800000Y-102550000D02* -X144100000Y-102850000D01* -X143250000Y-67200000D02* -X143250000Y-67300000D01* -X142550000Y-126350000D02* -X142285000Y-126085000D01* -X135900000Y-102800000D02* -X135900000Y-102700000D01* -X146150000Y-67400000D02* -X146450000Y-67400000D01* -X135200000Y-103500000D02* -X135900000Y-102800000D01* -X144387500Y-68900000D02* -X144200000Y-68712500D01* -X141700000Y-70000000D02* -X140775000Y-70000000D01* -X140050000Y-87500000D02* -X140500000Y-87950000D01* -X141855000Y-69875000D02* -X142250000Y-69480000D01* -X142550000Y-126350000D02* -X142800000Y-126600000D01* -X144180000Y-94650000D02* -X144555000Y-95025000D01* -X143387500Y-67400000D02* -X143537500Y-67550000D01* -X143600000Y-102550000D02* -X143500000Y-102550000D01* -X145475000Y-93225000D02* -X145800000Y-93225000D01* -X135485000Y-74889999D02* -X135485000Y-75139999D01* -X130700000Y-103450000D02* -X131400000Y-102750000D01* -X130199999Y-67300000D02* -X130449999Y-67550000D01* -X143500000Y-106650000D02* -X143300000Y-106450000D01* -X134300000Y-101000000D02* -X134025000Y-100725000D01* -X129550000Y-64300000D02* -X129800000Y-64050000D01* -X134300000Y-101000000D02* -X134550000Y-101250000D01* -X131020000Y-91780000D02* -X131020000Y-91750000D01* -X135800000Y-101000000D02* -X135525000Y-100725000D01* -X137650000Y-126050000D02* -X137400000Y-125800000D01* -X142250000Y-94550000D02* -X142000000Y-94550000D01* -X133650000Y-102750000D02* -X133650000Y-102700000D01* -X121575000Y-107350000D02* -X122025000Y-107800000D01* -X129550000Y-64300000D02* -X129280000Y-64570000D01* -X136800000Y-91900000D02* -X136535000Y-91635000D01* -X140775000Y-70000000D02* -X140750000Y-70025000D01* -X146150000Y-67400000D02* -X146012500Y-67400000D01* -X144550000Y-69000000D02* -X144550000Y-69350000D01* -X144270000Y-70030000D02* -X144270000Y-70000000D01* -X146450000Y-67400000D02* -X146500000Y-67450000D01* -X144000000Y-70300000D02* -X144270000Y-70030000D01* -X134700000Y-63775000D02* -X135000000Y-63475000D01* -X143337500Y-67250000D02* -X143537500Y-67050000D01* +X126450000Y-102274998D02* +X126450000Y-103600000D01* +X121280000Y-99730000D02* +X121260000Y-99750000D01* +D51* +X124750000Y-96250000D02* +X125750000Y-96250000D01* +X135650000Y-95350000D02* +X135250000Y-95750000D01* +D49* +X129200000Y-95936397D02* +X128886397Y-96250000D01* +D51* +X138525000Y-101510000D02* +X136610000Y-103425000D01* +X146500000Y-89650000D02* +X146500000Y-89200000D01* +D49* +X132242500Y-127762500D02* +X132680000Y-128200000D01* +X129062500Y-129062500D02* +X129200000Y-129200000D01* +X128990000Y-101514998D02* +X128990000Y-103600000D01* +X130400000Y-97050000D02* +X129800000Y-97050000D01* +X129562500Y-126100000D02* +X129562500Y-126437500D01* X135285000Y-76940000D02* X136285000Y-75940000D01* -X134025000Y-100725000D02* -X134025000Y-100700000D01* -X146040700Y-67871800D02* -X145862500Y-68050000D01* -X131550000Y-124100000D02* -X131800000Y-124350000D01* -X140200000Y-69600000D02* -X140000000Y-69400000D01* -X143600000Y-106650000D02* -X143500000Y-106650000D01* -X143600000Y-106650000D02* -X143800000Y-106650000D01* -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X131000000Y-100700000D02* -X129800000Y-100700000D01* -%TO.N,VBUS*% -D52* -X133366300Y-126245000D02* -X132646600Y-125525300D01* -X140500000Y-89525000D02* -X140553400Y-89578400D01* -X141321300Y-92762500D02* -X140762500Y-92762500D01* -X132646600Y-125525300D02* -X125770000Y-125525300D01* -X140762500Y-92762500D02* -X140025000Y-93500000D01* -X140553400Y-89578400D02* -X141703000Y-89578400D01* -X135845000Y-126245000D02* -X133366300Y-126245000D01* -%TO.N,3V3*% +X135485000Y-75139999D02* +X136285000Y-75940000D01* +X128700000Y-100300000D02* +X128700000Y-101224998D01* D51* -X144200000Y-66887500D02* -X144200000Y-67275900D01* -X125875000Y-100760000D02* -X125177200Y-101457800D01* -X141620700Y-90511600D02* -X142108100Y-90024200D01* -X145200000Y-68712500D02* -X145200000Y-69970000D01* -X139037500Y-91375000D02* -X139900900Y-90511600D01* -X123575000Y-107800000D02* -X124155300Y-107800000D01* -X147729900Y-93150200D02* -X144603900Y-90024200D01* -X146984200Y-84636800D02* -X146264000Y-83916600D01* -X146984200Y-87643900D02* -X146984200Y-84636800D01* -X125847800Y-103010000D02* -X123960000Y-104897800D01* -X144200000Y-66782200D02* -X144200000Y-66887500D01* -X131950000Y-112300000D02* -X133306900Y-113656900D01* -X142280000Y-68550000D02* -X142250000Y-68520000D01* -X123960000Y-105200000D02* -X123960000Y-107415000D01* -X123960000Y-107415000D02* -X123575000Y-107800000D01* -X144200000Y-67275900D02* -X145200000Y-68275900D01* -X142205000Y-68475000D02* -X142205000Y-67172700D01* -X139900900Y-90511600D02* -X141620700Y-90511600D01* -X143945100Y-66527300D02* -X144200000Y-66782200D01* -X145200000Y-69970000D02* -X145230000Y-70000000D01* -X142108100Y-90024200D02* -X144603900Y-90024200D01* -X146264000Y-83916600D02* -X146264000Y-71034000D01* -X140750000Y-68475000D02* -X142205000Y-68475000D01* -X147729900Y-97405000D02* -X147729900Y-93150200D01* -X142850400Y-66527300D02* -X143945100Y-66527300D01* -X145513100Y-113656900D02* -X145665000Y-113505000D01* -X125177200Y-101457800D02* -X125177200Y-102312200D01* -X143537500Y-68550000D02* -X142280000Y-68550000D01* -X146264000Y-71034000D02* -X145230000Y-70000000D01* -X125177200Y-102312200D02* -X125875000Y-103010000D01* -X123960000Y-104897800D02* -X123960000Y-105200000D01* -X146120300Y-98555000D02* -X146579900Y-98555000D01* -X124155300Y-107800000D02* -X124549200Y-107406100D01* -X133306900Y-113656900D02* -X145513100Y-113656900D01* -X146579900Y-98555000D02* -X147729900Y-97405000D01* -X144603900Y-90024200D02* -X146984200Y-87643900D01* -X144946700Y-98646700D02* -X146028600Y-98646700D01* -X124900000Y-94600000D02* -X124900000Y-99785000D01* -X124900000Y-99785000D02* -X125875000Y-100760000D01* -X142205000Y-67172700D02* -X142850400Y-66527300D01* -X125875000Y-103010000D02* -X125847800Y-103010000D01* -X142205000Y-68475000D02* -X142250000Y-68520000D01* -X144565000Y-98265000D02* -X144946700Y-98646700D01* -X145200000Y-68275900D02* -X145200000Y-68712500D01* -X146028600Y-98646700D02* -X146120300Y-98555000D01* -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X132216100Y-94700000D02* -X131797000Y-95119100D01* -X132525000Y-94700000D02* -X132216100Y-94700000D01* +X146500000Y-89200000D02* +X145400000Y-88100000D01* +D49* +X129562500Y-128425000D02* +X129562500Y-128062068D01* +X131774999Y-74440000D02* +X131774999Y-73449999D01* +X121850000Y-95250000D02* +X121850000Y-96650000D01* +X130400000Y-96650000D02* +X129800000Y-96650000D01* +X128349799Y-95084604D02* +X128905238Y-95084604D01* +D51* +X138525000Y-101510000D02* +X139240000Y-101510000D01* +D49* +X128160000Y-125900000D02* +X127680000Y-125900000D01* +X129862068Y-127762500D02* +X130725000Y-127762500D01* +D51* +X147475000Y-95750000D02* +X147475000Y-96525000D01* +D49* +X131742500Y-127262500D02* +X132680000Y-128200000D01* +X129062500Y-126100000D02* +X128360000Y-126100000D01* +X122500000Y-125200000D02* +X123000000Y-125700000D01* +X124100000Y-83700000D02* +X124100000Y-84376249D01* +D51* +X136610000Y-103425000D02* +X136610000Y-103600000D01* +D49* +X129062500Y-125637500D02* +X129062500Y-126100000D01* +X128905238Y-95084604D02* +X129200000Y-95379366D01* +D51* +X135650000Y-94250000D02* +X135650000Y-95350000D01* +D49* +X134900000Y-62800000D02* +X135000000Y-62700000D01* +X129562500Y-128837500D02* +X129562500Y-128425000D01* +%TO.N,/MCU_Core/MCU_BOOT*% +X144400000Y-108800000D02* +X142300000Y-108800000D01* +X142300000Y-108800000D02* +X139900000Y-106400000D01* +X144900000Y-108300000D02* +X144400000Y-108800000D01* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X129750000Y-92279366D02* +X130070634Y-92600000D01* +X129750000Y-91760000D02* +X129750000Y-92279366D01* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X133584200Y-87651600D02* -X133584200Y-89784000D01* -X132562200Y-93462800D02* -X132525000Y-93500000D01* -X132620800Y-86688200D02* -X133584200Y-87651600D01* -X133584200Y-89784000D02* -X132562200Y-90806000D01* -X132562200Y-90806000D02* -X132562200Y-93462800D01* +X122300000Y-107500000D02* +X124834314Y-107500000D01* +X131100000Y-113951471D02* +X131100000Y-115800000D01* +X124834314Y-107500000D02* +X127448529Y-110114215D01* +X121873930Y-107063387D02* +X121873930Y-107073930D01* +X121873930Y-107073930D02* +X122300000Y-107500000D01* +X127448529Y-110300000D02* +X131100000Y-113951471D01* +X131100000Y-115800000D02* +X130300000Y-116600000D01* +X127448529Y-110114215D02* +X127448529Y-110300000D01* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X138525000Y-99500000D02* -X139209300Y-100184300D01* -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X139789800Y-98443100D02* -X139705500Y-98443100D01* -X139705500Y-98443100D02* -X138525000Y-97262600D01* -X138525000Y-97262600D02* -X138525000Y-97100000D01* +X142600000Y-105300000D02* +X142600000Y-102400000D01* +X141300000Y-106600000D02* +X142600000Y-105300000D01* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X131025000Y-94700000D02* -X130420500Y-94095500D01* -X130420500Y-94095500D02* -X129065000Y-94095500D01* -%TO.N,VBAT*% -D52* -X134434600Y-119561400D02* -X133810600Y-118937400D01* -X141661400Y-119561400D02* -X134434600Y-119561400D01* -X145200000Y-123100000D02* -X141661400Y-119561400D01* -%TO.N,/MCU_Core/STAT2*% -D51* -X131025000Y-95900000D02* -X130425000Y-96500000D01* -X130425000Y-96500000D02* -X130387500Y-96500000D01* -%TO.N,/MCU_Core/STAT1*% -X129014300Y-101985600D02* -X129014300Y-97964600D01* -X123229900Y-117446900D02* -X123229900Y-109619600D01* -X129392800Y-102364100D02* -X129014300Y-101985600D01* -X129014300Y-97964600D02* -X129508400Y-97470500D01* -X123374000Y-117591000D02* -X123229900Y-117446900D01* -X130654500Y-97470500D02* -X131025000Y-97100000D01* -X129392800Y-103456700D02* -X129392800Y-102364100D01* -X129508400Y-97470500D02* -X130654500Y-97470500D01* -X123229900Y-109619600D02* -X129392800Y-103456700D01* +X128200000Y-105450002D02* +X128200000Y-108200000D01* +X129900000Y-109900000D02* +X130400000Y-109900000D01* +X128200000Y-108200000D02* +X129900000Y-109900000D01* %TO.N,/Accelerometer/I2C_SDA*% -X125875000Y-101990000D02* -X126522000Y-102637000D01* -X126365000Y-101500000D02* -X125875000Y-101990000D01* -X126522000Y-102637000D02* -X126522000Y-103407700D01* -X144513800Y-65652100D02* -X132254800Y-65652100D01* -X145200000Y-66887500D02* -X145200000Y-66338300D01* -X125180700Y-104749000D02* -X124959600Y-104749000D01* -X126522000Y-103407700D02* -X125180700Y-104749000D01* -X127900000Y-101500000D02* -X126365000Y-101500000D01* -X145200000Y-66338300D02* -X144513800Y-65652100D01* +X125684557Y-126762500D02* +X125422057Y-126500000D01* +X125422057Y-126500000D02* +X121800000Y-126500000D01* +X124200000Y-110200000D02* +X124600000Y-109800000D01* +X124200000Y-111600000D02* +X124200000Y-110200000D01* +X121800000Y-126500000D02* +X121800000Y-124755499D01* +X121800000Y-124755499D02* +X121874741Y-124680758D01* +X128900000Y-126762500D02* +X125684557Y-126762500D01* %TO.N,/Accelerometer/I2C_SCL*% -X127900000Y-100400000D02* -X126735300Y-100400000D01* -X125875000Y-99740000D02* -X126535000Y-100400000D01* -X144700000Y-66408600D02* -X144399800Y-66108400D01* -X144700000Y-66887500D02* -X144700000Y-66408600D01* -X131674400Y-70995100D02* -X126003900Y-70995100D01* -X141879900Y-66108400D02* -X139223000Y-68765300D01* -X131776000Y-71096700D02* -X131674400Y-70995100D01* -X144399800Y-66108400D02* -X141879900Y-66108400D01* -X126535000Y-100400000D02* -X126735300Y-100400000D01* -X139223000Y-68765300D02* -X139223000Y-69930200D01* -X138056500Y-71096700D02* -X131776000Y-71096700D01* -X139223000Y-69930200D02* -X138056500Y-71096700D01* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X140013100Y-88750100D02* -X143908100Y-88750100D01* -X138248600Y-90828900D02* -X139699100Y-89378400D01* -X146582500Y-85547000D02* -X145804700Y-84769200D01* -X146582500Y-86075700D02* -X146582500Y-85547000D01* -X138525000Y-93500000D02* -X138248600Y-93223600D01* -X139699100Y-89378400D02* -X139699100Y-89064100D01* -X143908100Y-88750100D02* -X146582500Y-86075700D01* -X139699100Y-89064100D02* -X140013100Y-88750100D01* -X138248600Y-93223600D02* -X138248600Y-90828900D01* -%TO.N,/USB_C/USB_CC1*% -X133999300Y-121502400D02* -X134400900Y-121100800D01* -X130265000Y-123815000D02* -X132577500Y-121502500D01* -X133999300Y-121502500D02* -X133999300Y-121502400D01* -X135349900Y-121100800D02* -X135750000Y-121500900D01* -X132577500Y-121502500D02* -X133999300Y-121502500D01* -X134400900Y-121100800D02* -X135349900Y-121100800D01* -%TO.N,/MCU_Core/USB_DP*% -X139484600Y-96501700D02* -X138882900Y-95900000D01* -X138882900Y-95900000D02* -X138525000Y-95900000D01* -%TO.N,/MCU_Core/USB_DM*% -X138525000Y-94700000D02* -X137983400Y-95241600D01* -X137983400Y-95241600D02* -X137901700Y-95241600D01* -%TO.N,/USB_C/USB_CC2*% -X141265000Y-126065000D02* -X138750000Y-126065000D01* -%TO.N,/MCU_Core/STICK_X*% -X126973300Y-93979800D02* -X126670100Y-93676600D01* -X127900000Y-97100000D02* -X126973300Y-97100000D01* -X126973300Y-97100000D02* -X126973300Y-93979800D01* -%TO.N,/MCU_Core/STICK_Y*% -X128290400Y-95609600D02* -X130207300Y-95609600D01* -X127900000Y-96000000D02* -X128290400Y-95609600D01* -%TO.N,/MCU_Core/3V3_RF*% -D52* -X144381800Y-93739700D02* -X145740400Y-95098300D01* -X142999700Y-92385900D02* -X142999700Y-92074700D01* -X145777600Y-95098300D02* -X146168800Y-95489500D01* -X146168800Y-95489500D02* -X146168800Y-96538100D01* -X142737000Y-93739700D02* -X142999700Y-93739700D01* -X146168800Y-96543800D02* -X146168800Y-96538100D01* -X146495000Y-96870000D02* -X146168800Y-96543800D01* -X142300000Y-91375000D02* -X140612500Y-91375000D01* -X127495600Y-64600000D02* -X126484400Y-65611200D01* -X127364200Y-67950000D02* -X127625000Y-67950000D01* -X142999700Y-92385900D02* -X142999700Y-93739700D01* -X142999700Y-92074700D02* -X142300000Y-91375000D01* -X145740400Y-95098300D02* -X145777600Y-95098300D01* -X145108100Y-96538100D02* -X144555000Y-95985000D01* -X142058600Y-93800000D02* -X142676700Y-93800000D01* -X132500000Y-69770000D02* -X129445000Y-69770000D01* -X145505000Y-76685000D02* -X144415000Y-76685000D01* -X140025000Y-95900000D02* -X139314400Y-95189400D01* -X139314400Y-92673100D02* -X140612500Y-91375000D01* -X142999700Y-93739700D02* -X144381800Y-93739700D01* -X142676700Y-93800000D02* -X142737000Y-93739700D01* -X146168800Y-96538100D02* -X145108100Y-96538100D01* -X126484400Y-67070200D02* -X127364200Y-67950000D01* -X142058600Y-93800000D02* -X141650000Y-93800000D01* -X126484400Y-65611200D02* -X126484400Y-67070200D01* -X128320000Y-64600000D02* -X127495600Y-64600000D01* -X129445000Y-69770000D02* -X127625000Y-67950000D01* -X139314400Y-95189400D02* -X139314400Y-92673100D01* -X144415000Y-76685000D02* -X143730000Y-76000000D01* +X121350000Y-127050000D02* +X121300000Y-127100000D01* +X128900000Y-127262500D02* +X128875000Y-127237500D01* +X128875000Y-127237500D02* +X128512068Y-127237500D01* +X121300000Y-125080210D02* +X121100000Y-124880210D01* +X121300000Y-127100000D02* +X121300000Y-125080210D01* +X125518871Y-127162500D02* +X125406372Y-127050000D01* +X128512068Y-127237500D02* +X128437068Y-127162500D01* +X128437068Y-127162500D02* +X125518871Y-127162500D01* +X125800000Y-111000000D02* +X125800000Y-109700000D01* +X125406372Y-127050000D02* +X121350000Y-127050000D01* +X122700000Y-114100000D02* +X125800000Y-111000000D01* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X139150000Y-105950000D02* +X139150000Y-103600000D01* +X138900000Y-106200000D02* +X139150000Y-105950000D01* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X135460000Y-102100000D02* +X135460000Y-101840000D01* +X134160000Y-100800000D02* +X133300000Y-100800000D01* +X135460000Y-106740000D02* +X135460000Y-102100000D01* +X135460000Y-102100000D02* +X134160000Y-100800000D01* +X135200000Y-107000000D02* +X135460000Y-106740000D01* +X135460000Y-101840000D02* +X136161765Y-101138235D01* +X133100000Y-107000000D02* +X135200000Y-107000000D01* +%TO.N,/MCU_Core/STAT2*% +X132840000Y-100050000D02* +X132700000Y-100190000D01* +X131450000Y-97134314D02* +X131450000Y-98660000D01* +X132700000Y-100190000D02* +X132700000Y-105751471D01* +X131450000Y-98660000D02* +X132840000Y-100050000D01* +X130565686Y-96250000D02* +X131450000Y-97134314D01* +X129800000Y-96250000D02* +X130565686Y-96250000D01* +X130824265Y-107627206D02* +X130824265Y-108075735D01* +X132700000Y-105751471D02* +X130824265Y-107627206D01* +%TO.N,/MCU_Core/STAT1*% +X124670000Y-97250000D02* +X125929900Y-97250000D01* +X130800000Y-108900000D02* +X130200000Y-108300000D01* +X130200000Y-108300000D02* +X130200000Y-100951471D01* +X124670000Y-97250000D02* +X125770000Y-97250000D01* +X127700000Y-95850000D02* +X127023386Y-95850000D01* +X130200000Y-100951471D02* +X128248529Y-99000000D01* +X128248529Y-99000000D02* +X127500000Y-99000000D01* +X125929900Y-97250000D02* +X126150000Y-97470100D01* +X126350000Y-96523385D02* +X126350000Y-96670000D01* +X126350000Y-96670000D02* +X125770000Y-97250000D01* +X127023386Y-95850000D02* +X126350000Y-96523385D01* %TO.N,/MCU_Core/BTN_STICK*% -D51* -X134025000Y-93500000D02* -X134709100Y-92815900D01* -X134709100Y-92815900D02* -X134709100Y-92787200D01* +X124482927Y-106582927D02* +X125048613Y-106582927D01* +X124350000Y-106450000D02* +X124482927Y-106582927D01* +X126600000Y-100400000D02* +X124350000Y-102650000D01* +X124350000Y-102650000D02* +X124350000Y-106450000D01* +X129265686Y-110800000D02* +X130500000Y-110800000D01* +X125048613Y-106582927D02* +X129265686Y-110800000D01* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X144107700Y-96699800D02* -X142754500Y-96699800D01* -X142754500Y-96699800D02* -X142054700Y-96000000D01* -X121650100Y-97070100D02* -X120688600Y-97070100D01* -X125920000Y-94600000D02* -X125920000Y-93123750D01* -X125311300Y-92614700D02* -X125311300Y-92515000D01* -X122070800Y-96649400D02* -X121650100Y-97070100D01* -X125311000Y-92615000D02* -X125311300Y-92614700D01* X125311250Y-92514999D02* X125311250Y-92715000D01* -X145452900Y-98045000D02* -X144107700Y-96699800D01* -X124043800Y-93975000D02* -X122070800Y-95948000D01* -X142054700Y-96000000D02* -X141650000Y-96000000D01* -X125920000Y-93123750D02* -X125311250Y-92515000D01* -X122070800Y-95948000D02* -X122070800Y-96649400D01* -X125920000Y-93975000D02* -X124043800Y-93975000D01* +X120600000Y-125765642D02* +X120600000Y-125309403D01* +X124200000Y-119800000D02* +X124900000Y-119800000D01* +X124000000Y-119600000D02* +X124200000Y-119800000D01* +X120500000Y-125209403D02* +X120500000Y-95090256D01* +X126351250Y-93775000D02* +X126361250Y-93764999D01* +X120600000Y-125309403D02* +X120500000Y-125209403D01* +X121825257Y-93764999D02* +X126361250Y-93764999D01* +X125311250Y-92715000D02* +X126361250Y-93764999D01* +X124900000Y-119800000D02* +X130500000Y-114200000D01* +X120500000Y-95090256D02* +X121825257Y-93764999D01* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X131700000Y-113800000D02* +X131700000Y-115100000D01* +X136225000Y-62700000D02* +X136225000Y-61800000D01* +X121893900Y-106234827D02* +X122642000Y-106982927D01* +X122300000Y-87800000D02* +X122800000Y-87300000D01* +X133775000Y-61800000D02* +X133775000Y-62700000D01* +X134375000Y-61200000D02* +X133775000Y-61800000D01* +X122800000Y-69500000D02* +X124500000Y-67800000D01* +X136225000Y-61800000D02* +X135625000Y-61200000D01* +X131000000Y-62700000D02* +X133780000Y-62700000D01* +X122800000Y-87300000D02* +X122800000Y-69496948D01* +X124882927Y-106982927D02* +X131700000Y-113800000D01* +X135625000Y-61200000D02* +X134375000Y-61200000D01* +X122642000Y-106982927D02* +X124882927Y-106982927D01* +%TO.N,/XBee/XBEE_CTS*% +X126450000Y-121300000D02* +X126450000Y-119150000D01* +X126450000Y-119150000D02* +X127800000Y-117800000D01* %TO.N,/MCU_Core/RGB_DIN*% -X134806300Y-110169700D02* -X139879900Y-105096100D01* -X133206700Y-110169700D02* -X134806300Y-110169700D01* -X129146500Y-114229900D02* -X133206700Y-110169700D01* -X139879900Y-105096100D02* -X139879900Y-99205500D01* -X129216700Y-123115100D02* -X129146500Y-123044900D01* -X141650000Y-98200000D02* -X140723300Y-98200000D01* -X129146500Y-123044900D02* -X129146500Y-114229900D01* -X140723300Y-98362100D02* -X140723300Y-98200000D01* -X139879900Y-99205500D02* -X140723300Y-98362100D01* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X125595700Y-91750400D02* -X126951700Y-93106400D01* -X130631400Y-93106400D02* -X131025000Y-93500000D01* -X123557800Y-90717300D02* -X124590900Y-91750400D01* -X123557800Y-90439600D02* -X123557800Y-90717300D01* -X124590900Y-91750400D02* -X125595700Y-91750400D01* -X126951700Y-93106400D02* -X130631400Y-93106400D01* +X126651471Y-124100000D02* +X127148529Y-124100000D01* +X126002198Y-123340339D02* +X126002198Y-123450727D01* +X127840000Y-119650000D02* +X130090000Y-117400000D01* +X130090000Y-117400000D02* +X130400000Y-117400000D01* +X127148529Y-124100000D02* +X127840000Y-123408529D01* +X127840000Y-123408529D02* +X127840000Y-119650000D01* +X126002198Y-123450727D02* +X126651471Y-124100000D01* +%TO.N,/XBee/XBEE_DIN*% +X130179998Y-120689999D02* +X129969997Y-120900000D01* +X129390000Y-120900000D02* +X128990000Y-121300000D01* +X129969997Y-120900000D02* +X129390000Y-120900000D01* +%TO.N,/XBee/XBEE_DOUT*% +X131615136Y-118535318D02* +X131530000Y-118620454D01* +X131530000Y-118620454D02* +X131530000Y-121300000D01* +%TO.N,ACCEL_INT1*% +X134062893Y-126770000D02* +X136480000Y-126770000D01* +X130562500Y-126100000D02* +X133392894Y-126100000D01* +X136480000Y-126770000D02* +X140351471Y-122898529D01* +X140351471Y-119300000D02* +X139400000Y-118348529D01* +X139400000Y-118348529D02* +X139400000Y-116900000D01* +X130562500Y-126100000D02* +X130562500Y-125937500D01* +X133392894Y-126100000D02* +X134062893Y-126770000D01* +X140351471Y-122898529D02* +X140351471Y-119300000D01* +X130562500Y-125937500D02* +X130600000Y-125900000D01* %TO.N,/Buttons_Direct/BTN_VOL_UP*% -X137025000Y-93500000D02* -X136186400Y-92661400D01* -X136186400Y-92661400D02* -X135734500Y-92661400D01* -%TO.N,/Power_Buck/PWR_EN*% -X140425000Y-80240000D02* -X140385000Y-80240000D01* -X140385000Y-80240000D02* -X139084999Y-78940000D01* -X140405000Y-80240000D02* -X145980700Y-85815700D01* -D53* -X138285000Y-78940000D02* -X139084999Y-78940000D01* -%TO.N,/Buttons_Direct/BTN_MACRO5*% +X147034358Y-98156239D02* +X147034358Y-107614171D01* +X147034358Y-107614171D02* +X137548529Y-117100000D01* +X134100000Y-117100000D02* +X133000000Y-118200000D01* +X137548529Y-117100000D02* +X134100000Y-117100000D01* +%TO.N,/XBee/XBEE_RTS*% +X134070000Y-118370000D02* +X134070000Y-121300000D01* +X133900000Y-118200000D02* +X134070000Y-118370000D01* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147700000Y-108000000D02* +X142100000Y-113600000D01* +X142100000Y-113600000D02* +X141751471Y-113600000D01* +X141262744Y-113951471D02* +X137714214Y-117500000D01* +X147700000Y-98600000D02* +X147700000Y-108000000D01* +X137700000Y-117500000D02* +X137500000Y-117700000D01* +X137500000Y-117700000D02* +X134700000Y-117700000D01* +X137714214Y-117500000D02* +X137700000Y-117500000D01* +X141400000Y-113951471D02* +X141262744Y-113951471D01* +X141751471Y-113600000D02* +X141400000Y-113951471D01* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135600000Y-118300000D02* +X136610000Y-119310000D01* +X136610000Y-119310000D02* +X136610000Y-121300000D01* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-118300000D02* +X139150000Y-120950000D01* +X139150000Y-120950000D02* +X139150000Y-121300000D01* +%TO.N,/MCU_Core/PWR_HOLD*% +X142700000Y-97600000D02* +X142700000Y-93500000D01* +X143200000Y-98100000D02* +X142700000Y-97600000D01* +X142000000Y-107300000D02* +X143200000Y-106100000D01* +D51* +X138385000Y-72440000D02* +X138485000Y-72539999D01* +D49* +X143200000Y-106100000D02* +X143200000Y-98100000D01* +D51* +X136935000Y-72440000D02* +X138385000Y-72440000D01* +D49* +X140950000Y-91750000D02* +X140950000Y-90700000D01* +X142700000Y-93500000D02* +X140950000Y-91750000D01* +%TO.N,VBUS*% +D51* +X125750000Y-95290000D02* +X123790000Y-95290000D01* +D52* +X121470000Y-103930000D02* +X121200000Y-104200000D01* +X121193900Y-106524777D02* +X121200000Y-106530877D01* +D49* +X123790000Y-95290000D02* +X123750000Y-95250000D01* +D52* +X121200000Y-105938777D02* +X121193900Y-105944877D01* +X122300000Y-102800000D02* +X121470000Y-103630000D01* +X121173930Y-107353337D02* +X121200000Y-107379407D01* +D49* +X125910000Y-95450000D02* +X125750000Y-95290000D01* +D52* +X133600000Y-125600000D02* +X134245000Y-126245000D01* +X121193900Y-105944877D02* +X121193900Y-106524777D01* +X131146016Y-124646016D02* +X132100000Y-125600000D01* +X125750000Y-124196016D02* +X126200000Y-124646016D01* +D49* +X127700000Y-95450000D02* +X125910000Y-95450000D01* +D52* +X126200000Y-124646016D02* +X131146016Y-124646016D01* +X135845000Y-126055000D02* +X137000000Y-124900000D01* +X121200000Y-106530877D02* +X121200000Y-106747367D01* +X132100000Y-125600000D02* +X133600000Y-125600000D01* +X121200000Y-106747367D02* +X121173930Y-106773437D01* +X121200000Y-122892031D02* +X122503984Y-124196016D01* +X121200000Y-107379407D02* +X121200000Y-122892031D01* +X121200000Y-104200000D02* +X121200000Y-105938777D01* +X134245000Y-126245000D02* +X135845000Y-126245000D01* +X122503984Y-124196016D02* +X125750000Y-124196016D01* +X121470000Y-103630000D02* +X121470000Y-103930000D01* +X135845000Y-126245000D02* +X135845000Y-126055000D01* +X121173930Y-106773437D02* +X121173930Y-107353337D01* +%TO.N,/USB_C/USB_CC1*% +D49* +X129200000Y-123700000D02* +X130150000Y-123700000D01* +X130150000Y-123700000D02* +X130265000Y-123815000D01* +%TO.N,/USB_C/USB_CC2*% +X142300000Y-124900000D02* +X142300000Y-125030000D01* +X142300000Y-125030000D02* +X141265000Y-126065000D01* +%TO.N,VSYS*% +D51* +X135350000Y-92650000D02* +X133750000Y-94250000D01* +D49* +X129800000Y-94800000D02* +X130350000Y-94250000D01* +X129700000Y-93350000D02* +X128461300Y-92111300D01* +D51* +X137113604Y-92650000D02* +X135350000Y-92650000D01* +D49* +X139235000Y-77065000D02* +X140680000Y-77065000D01* +X126868125Y-90131875D02* +X128461250Y-91725000D01* +D51* +X146525000Y-93475000D02* +X146375000Y-93475000D01* +D49* +X131250000Y-94250000D02* +X133750000Y-94250000D01* +X125881250Y-89145000D02* +X125881250Y-88965000D01* +D51* +X146525000Y-93475000D02* +X146525000Y-91575000D01* +X146525000Y-91575000D02* +X146500000Y-91550000D01* +D52* +X145600000Y-90650000D02* +X146500000Y-91550000D01* +X140785000Y-77985000D02* +X142100000Y-79300000D01* +D49* +X128461300Y-92111300D02* +X128461300Y-91725000D01* +D52* +X140785000Y-76960000D02* +X140785000Y-77985000D01* +D49* +X129700000Y-93350000D02* +X132850000Y-93350000D01* +X130350000Y-94250000D02* +X131250000Y-94250000D01* +X126868125Y-90131875D02* +X125881250Y-89145000D01* +D51* +X143463604Y-86300000D02* +X137113604Y-92650000D01* +D49* +X129800000Y-94800000D02* +X129800000Y-95450000D01* +X132850000Y-93350000D02* +X133750000Y-94250000D01* D51* -X137050000Y-101950000D02* -X137050000Y-103500000D01* -X138400000Y-100700000D02* -X138350000Y-100750000D01* -X138350000Y-100750000D02* -X138150000Y-100750000D01* -X136700000Y-103750000D02* -X136650000Y-103800000D01* -X138500000Y-100700000D02* -X138400000Y-100700000D01* -X137050000Y-103500000D02* -X136800000Y-103750000D01* -X136600000Y-103800000D02* -X136150000Y-104250000D01* -X137100000Y-101800000D02* -X137100000Y-101900000D01* -X136650000Y-103800000D02* -X136600000Y-103800000D01* -X138150000Y-100750000D02* -X137100000Y-101800000D01* -X137100000Y-101900000D02* -X137050000Y-101950000D01* -X136800000Y-103750000D02* -X136700000Y-103750000D01* +X144600000Y-86300000D02* +X143463604Y-86300000D01* +D52* +X144800000Y-90650000D02* +X145600000Y-90650000D01* %TO.N,/Power_Control/PWR_GATE*% -X140785000Y-75940000D02* -X138459999Y-75940000D01* -X135584999Y-78815000D02* -X134334999Y-78815000D01* -X138459999Y-75940000D02* -X137334999Y-77065000D01* +D49* X137334999Y-77065000D02* X135584999Y-78815000D01* +X138459999Y-75940000D02* +X137334999Y-77065000D01* +X135584999Y-78815000D02* +X134334999Y-78815000D01* +X140785000Y-75940000D02* +X138459999Y-75940000D01* +%TO.N,/Power_Buck/PWR_EN*% +D50* +X149300000Y-88500000D02* +X149108679Y-88500000D01* +D49* +X140425000Y-80240000D02* +X140425000Y-81010000D01* +D50* +X141643679Y-81035000D02* +X140400000Y-81035000D01* +X138285000Y-80985000D02* +X138285000Y-78940000D01* +X140400000Y-81035000D02* +X138335000Y-81035000D01* +X149108679Y-88500000D02* +X141643679Y-81035000D01* +X148425000Y-95750000D02* +X149300000Y-94875000D01* +D49* +X140425000Y-81010000D02* +X140400000Y-81035000D01* +D50* +X149300000Y-94875000D02* +X149300000Y-88500000D01* +X138335000Y-81035000D02* +X138285000Y-80985000D01* +D49* +X140425000Y-80240000D02* +X140385000Y-80240000D01* +%TO.N,VBAT*% +D50* +X135850000Y-98950000D02* +X135900000Y-99000000D01* +D49* +X131075000Y-95850000D02* +X129800000Y-95850000D01* +D50* +X145200000Y-119176016D02* +X145200000Y-123100000D01* +D51* +X132250000Y-97025000D02* +X131075000Y-95850000D01* +D50* +X132250000Y-97750000D02* +X133450000Y-98950000D01* +X133450000Y-98950000D02* +X135850000Y-98950000D01* +D51* +X132250000Y-97750000D02* +X132250000Y-97025000D01* +D50* +X147300000Y-109300000D02* +X147300000Y-117076016D01* +X147300000Y-117076016D02* +X145200000Y-119176016D01* %TO.N,/Power_Control/PWR_BTN_INV_BASE*% -X124861250Y-90539999D02* -X124661250Y-90740000D01* -X124061300Y-86915000D02* -X124061200Y-86915100D01* +D49* +X124061250Y-86914999D02* +X124861250Y-87715000D01* X124861250Y-88965000D02* X124861250Y-90539999D01* -X124861300Y-89127200D02* -X124861300Y-88965000D01* X124861250Y-87715000D02* X124861250Y-88965000D01* -X124861000Y-89127500D02* -X124861300Y-89127200D01* -X124661300Y-90739700D02* -X124661300Y-90740000D01* -X124061250Y-86914999D02* -X124861250Y-87715000D01* +X124861250Y-90539999D02* +X124661250Y-90740000D01* %TO.N,/Power_Control/PWR_LATCH_G*% X132334999Y-75440000D02* X132334999Y-74900000D01* +X132334999Y-75440000D02* +X132785000Y-75440000D01* +X132334999Y-75889999D02* +X132334999Y-76490000D01* +X132334999Y-75889999D02* +X132334999Y-75440000D01* +X132334999Y-76490000D02* +X130134999Y-78690000D01* X133634999Y-74590000D02* X133634999Y-72440000D01* -X132334999Y-75889999D02* -X133384999Y-76940000D01* +X132785000Y-75440000D02* +X133634999Y-74590000D01* X133935000Y-74889999D02* X133634999Y-74590000D01* X134524999Y-74889999D02* X133935000Y-74889999D01* -X132785000Y-75440000D02* -X133634999Y-74590000D01* -X132334999Y-75440000D02* -X132785000Y-75440000D01* -X132334999Y-76490000D02* -X130134999Y-78690000D01* X132334999Y-75889999D02* -X132334999Y-75440000D01* -X132334999Y-75889999D02* -X132334999Y-76490000D01* +X133384999Y-76940000D01* X132334999Y-74900000D02* X132795000Y-74440000D01* %TO.N,/Power_Control/PWR_BTN_TRIGGER*% -X125936300Y-85965000D02* -X125936200Y-85965100D01* X127536250Y-88514999D02* X127536250Y-87565000D01* -X126835000Y-78690000D02* -X125936000Y-79589000D01* +X126300000Y-85601300D02* +X125936300Y-85965000D01* X128461250Y-90704999D02* X128461250Y-88514999D01* -X128461250Y-88514999D02* -X127536250Y-88514999D01* -X125936000Y-79589000D02* -X125936000Y-85965000D01* +X126835000Y-78690000D02* +X126300000Y-79225000D01* X127536250Y-87565000D02* X125936250Y-85965000D01* -%TO.N,/MCU_Core/MCU_BOOT*% -X141650000Y-97100000D02* -X142576700Y-97100000D01* -X148250000Y-104800000D02* -X149076700Y-104800000D01* -X144100000Y-104800000D02* -X148250000Y-104800000D01* -X142576700Y-97296700D02* -X144565000Y-99285000D01* -X142576700Y-97100000D02* -X142576700Y-97296700D01* -X149076700Y-100179300D02* -X148182400Y-99285000D01* -X149076700Y-104800000D02* -X149076700Y-100179300D01* -X148182400Y-99285000D02* -X144565000Y-99285000D01* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X133126700Y-101010700D02* -X132670900Y-101466500D01* -X129750000Y-91760000D02* -X130372400Y-91137600D01* -X129005300Y-92504700D02* -X127525700Y-92504700D01* -X130372400Y-91137600D02* -X131367600Y-91137600D01* -X133126700Y-97701700D02* -X133126700Y-101010700D01* -X129750000Y-91760000D02* -X129005300Y-92504700D01* -X130377400Y-101466500D02* -X129861700Y-101982200D01* -X131367600Y-91137600D02* -X131980000Y-91750000D01* -X132525000Y-97100000D02* -X133126700Y-97701700D01* -X132670900Y-101466500D02* -X130377400Y-101466500D01* -%TO.N,ACCEL_INT1*% -X145862500Y-68550000D02* -X147014800Y-69702300D01* -X129871400Y-99693700D02* -X130831300Y-99693700D01* -X147014800Y-69702300D02* -X147014800Y-76170200D01* -X130831300Y-99693700D02* -X131025000Y-99500000D01* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X135898900Y-62373900D02* -X135898900Y-61973000D01* -X135525000Y-93500000D02* -X134775000Y-94250000D01* -X135898900Y-61973000D02* -X135413700Y-61487800D01* -X134603900Y-61487800D02* -X133775000Y-62316700D01* -X135413700Y-61487800D02* -X135000000Y-61487800D01* -X133775000Y-62316700D02* -X133775000Y-62700000D01* -X135000000Y-61487800D02* -X134603900Y-61487800D01* -X134775000Y-94250000D02* -X134775000Y-95096400D01* -X136225000Y-62700000D02* -X135898900Y-62373900D01* -X135000000Y-61269100D02* -X135000000Y-61487800D01* -%TO.N,/MCU_Core/SWDIO*% -X148791000Y-111974600D02* -X148791000Y-109108000D01* -X143871100Y-105887600D02* -X142171300Y-104187800D01* -X142171300Y-102394100D02* -X142576700Y-101988700D01* -X145570600Y-105887600D02* -X143871100Y-105887600D01* -X147260600Y-113505000D02* -X148791000Y-111974600D01* -X146935000Y-113505000D02* -X147260600Y-113505000D01* -X141650000Y-101500000D02* -X142576700Y-101500000D01* -X148791000Y-109108000D02* -X145570600Y-105887600D01* -X142576700Y-101988700D02* -X142576700Y-101500000D01* -X142171300Y-104187800D02* -X142171300Y-102394100D01* -%TO.N,/MCU_Core/MCU_RESET*% -X140305900Y-106946600D02* -X140305900Y-99717400D01* -X144100000Y-100700000D02* -X143273300Y-100700000D01* -X148250000Y-100700000D02* -X144100000Y-100700000D01* -X141650000Y-99300000D02* -X140723300Y-99300000D01* -X141650000Y-99300000D02* -X142576700Y-99300000D01* -X142576700Y-100003400D02* -X143273300Y-100700000D01* -X140305900Y-99717400D02* -X140723300Y-99300000D01* -X142576700Y-99300000D02* -X142576700Y-100003400D01* -X145665000Y-112235000D02* -X145594300Y-112235000D01* -X145594300Y-112235000D02* -X140305900Y-106946600D01* -%TO.N,/MCU_Core/SWDCLK*% -X140723300Y-104899600D02* -X144192700Y-108369000D01* -X148389300Y-109274300D02* -X148389300Y-110674600D01* -X147484000Y-108369000D02* -X148389300Y-109274300D01* -X148389300Y-110674600D02* -X146935000Y-112128900D01* -X144192700Y-108369000D02* -X147484000Y-108369000D01* -X146935000Y-112128900D02* -X146935000Y-112235000D01* -X140723300Y-100400000D02* -X140723300Y-104899600D01* -X141650000Y-100400000D02* -X140723300Y-100400000D01* -%TO.N,/MCU_Core/PWR_HOLD*% -D54* -X138385000Y-72440000D02* -X138485000Y-72539999D01* -D51* -X129625000Y-98237500D02* -X130962500Y-98237500D01* -X130962500Y-98237500D02* -X131025000Y-98300000D01* -D54* -X136935000Y-72440000D02* -X138385000Y-72440000D01* -%TO.N,/MCU_Core/VSYS_SENSE*% +X128461250Y-88514999D02* +X127536250Y-88514999D01* +X126300000Y-79225000D02* +X126300000Y-85601300D01* +%TO.N,/Power_Charger/CHG_TS*% +X124350000Y-101250000D02* +X122280000Y-101250000D01* +X127700000Y-97050000D02* +X127700000Y-97900000D01* +X127700000Y-97900000D02* +X124350000Y-101250000D01* +%TO.N,/Power_Charger/CHG_VSET*% +X125784314Y-99250000D02* +X125284314Y-99750000D01* +X125784314Y-99250000D02* +X127250000Y-97784314D01* +X125284314Y-99750000D02* +X122280000Y-99750000D01* +X127150000Y-96854756D02* +X127354756Y-96650000D01* +X127354756Y-96650000D02* +X127700000Y-96650000D01* +X127150000Y-97245244D02* +X127150000Y-96854756D01* +X127250000Y-97345244D02* +X127150000Y-97245244D01* +X127250000Y-97784314D02* +X127250000Y-97345244D01* +%TO.N,/Power_Charger/CHG_ISET*% +X127189071Y-96250000D02* +X127700000Y-96250000D01* +X125618628Y-98850000D02* +X126750000Y-97718628D01* +X126750000Y-96689070D02* +X127189071Y-96250000D01* +X126750000Y-97718628D02* +X126750000Y-96689070D01* +X122300000Y-98250000D02* +X122900000Y-98850000D01* +X122900000Y-98850000D02* +X125618628Y-98850000D01* +%TO.N,/Power_Buck/BUCK_FB*% D51* -X133150000Y-95100000D02* -X133150000Y-94450000D01* -X132650000Y-95750000D02* -X132650000Y-95650000D01* -X133100000Y-95150000D02* -X133150000Y-95100000D01* -X132525000Y-95875000D02* -X132525000Y-95900000D01* -X135515000Y-91615000D02* -X134285000Y-91615000D01* -X134285000Y-91665000D02* -X134285000Y-91615000D01* -X134250000Y-91700000D02* -X134285000Y-91665000D01* -X133100000Y-95200000D02* -X133100000Y-95150000D01* -X133150000Y-94450000D02* -X133350000Y-94250000D01* -X133350000Y-92600000D02* -X134250000Y-91700000D01* -X132650000Y-95650000D02* -X133100000Y-95200000D01* -X133350000Y-94250000D02* -X133350000Y-92600000D01* -X132500000Y-95900000D02* -X132650000Y-95750000D01* +X139860758Y-98200000D02* +X139835000Y-98200000D01* +X148324795Y-88600000D02* +X148562397Y-88837603D01* +X139885887Y-98225129D02* +X139860758Y-98200000D01* +X143400000Y-87300000D02* +X146800000Y-87300000D01* +X140300000Y-92200000D02* +X140300000Y-90400000D01* +X148425000Y-88975000D02* +X148425000Y-93475000D01* +X139600000Y-93500000D02* +X139600000Y-92900000D01* +X140300000Y-90400000D02* +X143400000Y-87300000D01* +X139500000Y-93600000D02* +X139600000Y-93500000D01* +X139500000Y-94850000D02* +X139500000Y-93600000D01* +X139600000Y-92900000D02* +X140300000Y-92200000D01* +X138525000Y-100490000D02* +X138525000Y-99510000D01* +X148100000Y-88600000D02* +X148324795Y-88600000D01* +X148562397Y-88837603D02* +X148425000Y-88975000D01* +X146800000Y-87300000D02* +X148100000Y-88600000D01* +X139835000Y-98200000D02* +X138525000Y-99510000D01* +%TO.N,/Power_Buck/BUCK_SW*% +D53* +X146525000Y-95750000D02* +X144050000Y-95750000D01* %TO.N,/Hall_Trigger/TRIG_ANALOG*% -X130251700Y-85169900D02* -X133182500Y-88100700D01* -X130251700Y-82814200D02* -X130251700Y-85169900D01* -X132070700Y-90455500D02* -X130034500Y-90455500D01* -X130034500Y-90455500D02* +D49* +X129750000Y-88400648D02* X129750000Y-90740000D01* -X133182500Y-89343700D02* -X132070700Y-90455500D01* -X128066200Y-80628700D02* -X130251700Y-82814200D01* -X133182500Y-88100700D02* -X133182500Y-89343700D01* -X127260700Y-66414300D02* -X127260700Y-66852300D01* -X126692500Y-80628700D02* -X128066200Y-80628700D01* -X127625000Y-66050000D02* -X127260700Y-66414300D01* +X127100000Y-82847613D02* +X127100000Y-84152387D01* +X127600000Y-74652387D02* +X127600000Y-82347613D01* +X127100000Y-74152387D02* +X127600000Y-74652387D01* +X127437500Y-68387500D02* +X127437500Y-65700000D01* +X127600000Y-84652387D02* +X127600000Y-86250648D01* +X127600000Y-86250648D02* +X129750000Y-88400648D01* +X127600000Y-72347613D02* +X127100000Y-72847613D01* +X127100000Y-72847613D02* +X127100000Y-74152387D01* +X127600000Y-68550000D02* +X127600000Y-72347613D01* +X127600000Y-82347613D02* +X127100000Y-82847613D01* +X127600000Y-68550000D02* +X127437500Y-68387500D01* +X127100000Y-84152387D02* +X127600000Y-84652387D01* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-B_Mask.gbr b/PCB/v2.x/production/gerbers/snips_controller-B_Mask.gbr index 6a1f0a2..e13ff8e 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-B_Mask.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-B_Mask.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Soldermask,Bot*% %TF.FilePolarity,Negative*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -29,104 +29,2886 @@ G04 Aperture macros list* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% G04 Aperture macros list end* -%ADD10C,0.900000*% -%ADD11C,2.200000*% -%ADD12C,0.650000*% -%ADD13O,1.000000X2.100000*% -%ADD14O,1.000000X1.600000*% -%ADD15C,2.750000*% -%ADD16C,2.250000*% -%ADD17C,2.450000*% -%ADD18RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% -%ADD19RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% -%ADD20RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% -%ADD21RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% -%ADD22RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% -%ADD23O,1.200000X1.750000*% -%ADD24C,2.000000*% -%ADD25RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% -%ADD26RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% -%ADD27RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% -%ADD28R,1.050000X0.650000*% -%ADD29RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% -%ADD30RoundRect,0.218750X-0.218750X-0.256250X0.218750X-0.256250X0.218750X0.256250X-0.218750X0.256250X0*% -%ADD31RoundRect,0.087500X0.225000X0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0*% -%ADD32RoundRect,0.087500X0.087500X0.225000X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0*% -%ADD33RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% -%ADD34RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% -%ADD35RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% -%ADD36RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% -%ADD37RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% -%ADD38RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% -%ADD39C,0.990600*% -%ADD40C,0.787400*% -%ADD41RoundRect,0.225000X-0.250000X0.225000X-0.250000X-0.225000X0.250000X-0.225000X0.250000X0.225000X0*% +%ADD10C,0.010000*% +%ADD11C,0.900000*% +%ADD12C,2.200000*% +%ADD13C,0.650000*% +%ADD14O,1.000000X2.100000*% +%ADD15O,1.000000X1.600000*% +%ADD16C,2.750000*% +%ADD17C,2.250000*% +%ADD18C,2.450000*% +%ADD19RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% +%ADD20RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% +%ADD21RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% +%ADD22RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% +%ADD23RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% +%ADD24O,1.200000X1.750000*% +%ADD25C,2.000000*% +%ADD26RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% +%ADD27RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% +%ADD28RoundRect,0.250000X-0.475000X0.250000X-0.475000X-0.250000X0.475000X-0.250000X0.475000X0.250000X0*% +%ADD29RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% +%ADD30RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% +%ADD31RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD32RoundRect,0.087500X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0.087500X0.225000X0*% +%ADD33RoundRect,0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0.225000X0.087500X0*% +%ADD34RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% +%ADD35RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%ADD36RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% +%ADD37RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% +%ADD38RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% +%ADD39RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% +%ADD40RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% +%ADD41RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% %ADD42RoundRect,0.225000X-0.225000X-0.375000X0.225000X-0.375000X0.225000X0.375000X-0.225000X0.375000X0*% -%ADD43R,1.250000X0.700000*% -%ADD44C,0.600000*% -%ADD45R,1.500000X1.500000*% -%ADD46R,0.600000X0.600000*% -%ADD47RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% -%ADD48RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% -%ADD49RoundRect,0.250000X0.650000X-0.325000X0.650000X0.325000X-0.650000X0.325000X-0.650000X-0.325000X0*% -%ADD50RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% -%ADD51RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% -%ADD52RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD43RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD44R,1.700000X2.700000*% +%ADD45RoundRect,0.150000X0.150000X-0.512500X0.150000X0.512500X-0.150000X0.512500X-0.150000X-0.512500X0*% +%ADD46R,1.500000X3.600000*% +%ADD47RoundRect,0.150000X0.587500X0.150000X-0.587500X0.150000X-0.587500X-0.150000X0.587500X-0.150000X0*% +%ADD48RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% G04 APERTURE END LIST* D10* +%TO.C,U_CHG1*% +X128000000Y-95550000D02* +X128000000Y-95350000D01* +X128000000Y-95347000D01* +X128000000Y-95345000D01* +X127999000Y-95342000D01* +X127999000Y-95340000D01* +X127998000Y-95337000D01* +X127998000Y-95335000D01* +X127997000Y-95332000D01* +X127996000Y-95330000D01* +X127995000Y-95327000D01* +X127993000Y-95325000D01* +X127992000Y-95323000D01* +X127990000Y-95321000D01* +X127989000Y-95319000D01* +X127987000Y-95317000D01* +X127985000Y-95315000D01* +X127983000Y-95313000D01* +X127981000Y-95311000D01* +X127979000Y-95310000D01* +X127977000Y-95308000D01* +X127975000Y-95307000D01* +X127973000Y-95305000D01* +X127970000Y-95304000D01* +X127968000Y-95303000D01* +X127965000Y-95302000D01* +X127963000Y-95302000D01* +X127960000Y-95301000D01* +X127958000Y-95301000D01* +X127955000Y-95300000D01* +X127953000Y-95300000D01* +X127950000Y-95300000D01* +X127450000Y-95300000D01* +X127447000Y-95300000D01* +X127445000Y-95300000D01* +X127442000Y-95301000D01* +X127440000Y-95301000D01* +X127437000Y-95302000D01* +X127435000Y-95302000D01* +X127432000Y-95303000D01* +X127430000Y-95304000D01* +X127427000Y-95305000D01* +X127425000Y-95307000D01* +X127423000Y-95308000D01* +X127421000Y-95310000D01* +X127419000Y-95311000D01* +X127417000Y-95313000D01* +X127415000Y-95315000D01* +X127413000Y-95317000D01* +X127411000Y-95319000D01* +X127410000Y-95321000D01* +X127408000Y-95323000D01* +X127407000Y-95325000D01* +X127405000Y-95327000D01* +X127404000Y-95330000D01* +X127403000Y-95332000D01* +X127402000Y-95335000D01* +X127402000Y-95337000D01* +X127401000Y-95340000D01* +X127401000Y-95342000D01* +X127400000Y-95345000D01* +X127400000Y-95347000D01* +X127400000Y-95350000D01* +X127400000Y-95550000D01* +X127400000Y-95553000D01* +X127400000Y-95555000D01* +X127401000Y-95558000D01* +X127401000Y-95560000D01* +X127402000Y-95563000D01* +X127402000Y-95565000D01* +X127403000Y-95568000D01* +X127404000Y-95570000D01* +X127405000Y-95573000D01* +X127407000Y-95575000D01* +X127408000Y-95577000D01* +X127410000Y-95579000D01* +X127411000Y-95581000D01* +X127413000Y-95583000D01* +X127415000Y-95585000D01* +X127417000Y-95587000D01* +X127419000Y-95589000D01* +X127421000Y-95590000D01* +X127423000Y-95592000D01* +X127425000Y-95593000D01* +X127427000Y-95595000D01* +X127430000Y-95596000D01* +X127432000Y-95597000D01* +X127435000Y-95598000D01* +X127437000Y-95598000D01* +X127440000Y-95599000D01* +X127442000Y-95599000D01* +X127445000Y-95600000D01* +X127447000Y-95600000D01* +X127450000Y-95600000D01* +X127950000Y-95600000D01* +X127953000Y-95600000D01* +X127955000Y-95600000D01* +X127958000Y-95599000D01* +X127960000Y-95599000D01* +X127963000Y-95598000D01* +X127965000Y-95598000D01* +X127968000Y-95597000D01* +X127970000Y-95596000D01* +X127973000Y-95595000D01* +X127975000Y-95593000D01* +X127977000Y-95592000D01* +X127979000Y-95590000D01* +X127981000Y-95589000D01* +X127983000Y-95587000D01* +X127985000Y-95585000D01* +X127987000Y-95583000D01* +X127989000Y-95581000D01* +X127990000Y-95579000D01* +X127992000Y-95577000D01* +X127993000Y-95575000D01* +X127995000Y-95573000D01* +X127996000Y-95570000D01* +X127997000Y-95568000D01* +X127998000Y-95565000D01* +X127998000Y-95563000D01* +X127999000Y-95560000D01* +X127999000Y-95558000D01* +X128000000Y-95555000D01* +X128000000Y-95553000D01* +X128000000Y-95550000D01* +G36* +X127958000Y-95301000D02* +G01* +X127960000Y-95301000D01* +X127963000Y-95302000D01* +X127965000Y-95302000D01* +X127968000Y-95303000D01* +X127970000Y-95304000D01* +X127973000Y-95305000D01* +X127975000Y-95307000D01* +X127977000Y-95308000D01* +X127979000Y-95310000D01* +X127981000Y-95311000D01* +X127983000Y-95313000D01* +X127985000Y-95315000D01* +X127987000Y-95317000D01* +X127989000Y-95319000D01* +X127990000Y-95321000D01* +X127992000Y-95323000D01* +X127993000Y-95325000D01* +X127995000Y-95327000D01* +X127996000Y-95330000D01* +X127997000Y-95332000D01* +X127998000Y-95335000D01* +X127998000Y-95337000D01* +X127999000Y-95340000D01* +X127999000Y-95342000D01* +X128000000Y-95345000D01* +X128000000Y-95347000D01* +X128000000Y-95350000D01* +X128000000Y-95550000D01* +X128000000Y-95553000D01* +X128000000Y-95555000D01* +X127999000Y-95558000D01* +X127999000Y-95560000D01* +X127998000Y-95563000D01* +X127998000Y-95565000D01* +X127997000Y-95568000D01* +X127996000Y-95570000D01* +X127995000Y-95573000D01* +X127993000Y-95575000D01* +X127992000Y-95577000D01* +X127990000Y-95579000D01* +X127989000Y-95581000D01* +X127987000Y-95583000D01* +X127985000Y-95585000D01* +X127983000Y-95587000D01* +X127981000Y-95589000D01* +X127979000Y-95590000D01* +X127977000Y-95592000D01* +X127975000Y-95593000D01* +X127973000Y-95595000D01* +X127970000Y-95596000D01* +X127968000Y-95597000D01* +X127965000Y-95598000D01* +X127963000Y-95598000D01* +X127960000Y-95599000D01* +X127958000Y-95599000D01* +X127955000Y-95600000D01* +X127953000Y-95600000D01* +X127950000Y-95600000D01* +X127450000Y-95600000D01* +X127447000Y-95600000D01* +X127445000Y-95600000D01* +X127442000Y-95599000D01* +X127440000Y-95599000D01* +X127437000Y-95598000D01* +X127435000Y-95598000D01* +X127432000Y-95597000D01* +X127430000Y-95596000D01* +X127427000Y-95595000D01* +X127425000Y-95593000D01* +X127423000Y-95592000D01* +X127421000Y-95590000D01* +X127419000Y-95589000D01* +X127417000Y-95587000D01* +X127415000Y-95585000D01* +X127413000Y-95583000D01* +X127411000Y-95581000D01* +X127410000Y-95579000D01* +X127408000Y-95577000D01* +X127407000Y-95575000D01* +X127405000Y-95573000D01* +X127404000Y-95570000D01* +X127403000Y-95568000D01* +X127402000Y-95565000D01* +X127402000Y-95563000D01* +X127401000Y-95560000D01* +X127401000Y-95558000D01* +X127400000Y-95555000D01* +X127400000Y-95553000D01* +X127400000Y-95550000D01* +X127400000Y-95350000D01* +X127400000Y-95347000D01* +X127400000Y-95345000D01* +X127401000Y-95342000D01* +X127401000Y-95340000D01* +X127402000Y-95337000D01* +X127402000Y-95335000D01* +X127403000Y-95332000D01* +X127404000Y-95330000D01* +X127405000Y-95327000D01* +X127407000Y-95325000D01* +X127408000Y-95323000D01* +X127410000Y-95321000D01* +X127411000Y-95319000D01* +X127413000Y-95317000D01* +X127415000Y-95315000D01* +X127417000Y-95313000D01* +X127419000Y-95311000D01* +X127421000Y-95310000D01* +X127423000Y-95308000D01* +X127425000Y-95307000D01* +X127427000Y-95305000D01* +X127430000Y-95304000D01* +X127432000Y-95303000D01* +X127435000Y-95302000D01* +X127437000Y-95302000D01* +X127440000Y-95301000D01* +X127442000Y-95301000D01* +X127445000Y-95300000D01* +X127447000Y-95300000D01* +X127450000Y-95300000D01* +X127950000Y-95300000D01* +X127953000Y-95300000D01* +X127955000Y-95300000D01* +X127958000Y-95301000D01* +G37* +X128000000Y-95950000D02* +X128000000Y-95750000D01* +X128000000Y-95747000D01* +X128000000Y-95745000D01* +X127999000Y-95742000D01* +X127999000Y-95740000D01* +X127998000Y-95737000D01* +X127998000Y-95735000D01* +X127997000Y-95732000D01* +X127996000Y-95730000D01* +X127995000Y-95727000D01* +X127993000Y-95725000D01* +X127992000Y-95723000D01* +X127990000Y-95721000D01* +X127989000Y-95719000D01* +X127987000Y-95717000D01* +X127985000Y-95715000D01* +X127983000Y-95713000D01* +X127981000Y-95711000D01* +X127979000Y-95710000D01* +X127977000Y-95708000D01* +X127975000Y-95707000D01* +X127973000Y-95705000D01* +X127970000Y-95704000D01* +X127968000Y-95703000D01* +X127965000Y-95702000D01* +X127963000Y-95702000D01* +X127960000Y-95701000D01* +X127958000Y-95701000D01* +X127955000Y-95700000D01* +X127953000Y-95700000D01* +X127950000Y-95700000D01* +X127450000Y-95700000D01* +X127447000Y-95700000D01* +X127445000Y-95700000D01* +X127442000Y-95701000D01* +X127440000Y-95701000D01* +X127437000Y-95702000D01* +X127435000Y-95702000D01* +X127432000Y-95703000D01* +X127430000Y-95704000D01* +X127427000Y-95705000D01* +X127425000Y-95707000D01* +X127423000Y-95708000D01* +X127421000Y-95710000D01* +X127419000Y-95711000D01* +X127417000Y-95713000D01* +X127415000Y-95715000D01* +X127413000Y-95717000D01* +X127411000Y-95719000D01* +X127410000Y-95721000D01* +X127408000Y-95723000D01* +X127407000Y-95725000D01* +X127405000Y-95727000D01* +X127404000Y-95730000D01* +X127403000Y-95732000D01* +X127402000Y-95735000D01* +X127402000Y-95737000D01* +X127401000Y-95740000D01* +X127401000Y-95742000D01* +X127400000Y-95745000D01* +X127400000Y-95747000D01* +X127400000Y-95750000D01* +X127400000Y-95950000D01* +X127400000Y-95953000D01* +X127400000Y-95955000D01* +X127401000Y-95958000D01* +X127401000Y-95960000D01* +X127402000Y-95963000D01* +X127402000Y-95965000D01* +X127403000Y-95968000D01* +X127404000Y-95970000D01* +X127405000Y-95973000D01* +X127407000Y-95975000D01* +X127408000Y-95977000D01* +X127410000Y-95979000D01* +X127411000Y-95981000D01* +X127413000Y-95983000D01* +X127415000Y-95985000D01* +X127417000Y-95987000D01* +X127419000Y-95989000D01* +X127421000Y-95990000D01* +X127423000Y-95992000D01* +X127425000Y-95993000D01* +X127427000Y-95995000D01* +X127430000Y-95996000D01* +X127432000Y-95997000D01* +X127435000Y-95998000D01* +X127437000Y-95998000D01* +X127440000Y-95999000D01* +X127442000Y-95999000D01* +X127445000Y-96000000D01* +X127447000Y-96000000D01* +X127450000Y-96000000D01* +X127950000Y-96000000D01* +X127953000Y-96000000D01* +X127955000Y-96000000D01* +X127958000Y-95999000D01* +X127960000Y-95999000D01* +X127963000Y-95998000D01* +X127965000Y-95998000D01* +X127968000Y-95997000D01* +X127970000Y-95996000D01* +X127973000Y-95995000D01* +X127975000Y-95993000D01* +X127977000Y-95992000D01* +X127979000Y-95990000D01* +X127981000Y-95989000D01* +X127983000Y-95987000D01* +X127985000Y-95985000D01* +X127987000Y-95983000D01* +X127989000Y-95981000D01* +X127990000Y-95979000D01* +X127992000Y-95977000D01* +X127993000Y-95975000D01* +X127995000Y-95973000D01* +X127996000Y-95970000D01* +X127997000Y-95968000D01* +X127998000Y-95965000D01* +X127998000Y-95963000D01* +X127999000Y-95960000D01* +X127999000Y-95958000D01* +X128000000Y-95955000D01* +X128000000Y-95953000D01* +X128000000Y-95950000D01* +G36* +X127958000Y-95701000D02* +G01* +X127960000Y-95701000D01* +X127963000Y-95702000D01* +X127965000Y-95702000D01* +X127968000Y-95703000D01* +X127970000Y-95704000D01* +X127973000Y-95705000D01* +X127975000Y-95707000D01* +X127977000Y-95708000D01* +X127979000Y-95710000D01* +X127981000Y-95711000D01* +X127983000Y-95713000D01* +X127985000Y-95715000D01* +X127987000Y-95717000D01* +X127989000Y-95719000D01* +X127990000Y-95721000D01* +X127992000Y-95723000D01* +X127993000Y-95725000D01* +X127995000Y-95727000D01* +X127996000Y-95730000D01* +X127997000Y-95732000D01* +X127998000Y-95735000D01* +X127998000Y-95737000D01* +X127999000Y-95740000D01* +X127999000Y-95742000D01* +X128000000Y-95745000D01* +X128000000Y-95747000D01* +X128000000Y-95750000D01* +X128000000Y-95950000D01* +X128000000Y-95953000D01* +X128000000Y-95955000D01* +X127999000Y-95958000D01* +X127999000Y-95960000D01* +X127998000Y-95963000D01* +X127998000Y-95965000D01* +X127997000Y-95968000D01* +X127996000Y-95970000D01* +X127995000Y-95973000D01* +X127993000Y-95975000D01* +X127992000Y-95977000D01* +X127990000Y-95979000D01* +X127989000Y-95981000D01* +X127987000Y-95983000D01* +X127985000Y-95985000D01* +X127983000Y-95987000D01* +X127981000Y-95989000D01* +X127979000Y-95990000D01* +X127977000Y-95992000D01* +X127975000Y-95993000D01* +X127973000Y-95995000D01* +X127970000Y-95996000D01* +X127968000Y-95997000D01* +X127965000Y-95998000D01* +X127963000Y-95998000D01* +X127960000Y-95999000D01* +X127958000Y-95999000D01* +X127955000Y-96000000D01* +X127953000Y-96000000D01* +X127950000Y-96000000D01* +X127450000Y-96000000D01* +X127447000Y-96000000D01* +X127445000Y-96000000D01* +X127442000Y-95999000D01* +X127440000Y-95999000D01* +X127437000Y-95998000D01* +X127435000Y-95998000D01* +X127432000Y-95997000D01* +X127430000Y-95996000D01* +X127427000Y-95995000D01* +X127425000Y-95993000D01* +X127423000Y-95992000D01* +X127421000Y-95990000D01* +X127419000Y-95989000D01* +X127417000Y-95987000D01* +X127415000Y-95985000D01* +X127413000Y-95983000D01* +X127411000Y-95981000D01* +X127410000Y-95979000D01* +X127408000Y-95977000D01* +X127407000Y-95975000D01* +X127405000Y-95973000D01* +X127404000Y-95970000D01* +X127403000Y-95968000D01* +X127402000Y-95965000D01* +X127402000Y-95963000D01* +X127401000Y-95960000D01* +X127401000Y-95958000D01* +X127400000Y-95955000D01* +X127400000Y-95953000D01* +X127400000Y-95950000D01* +X127400000Y-95750000D01* +X127400000Y-95747000D01* +X127400000Y-95745000D01* +X127401000Y-95742000D01* +X127401000Y-95740000D01* +X127402000Y-95737000D01* +X127402000Y-95735000D01* +X127403000Y-95732000D01* +X127404000Y-95730000D01* +X127405000Y-95727000D01* +X127407000Y-95725000D01* +X127408000Y-95723000D01* +X127410000Y-95721000D01* +X127411000Y-95719000D01* +X127413000Y-95717000D01* +X127415000Y-95715000D01* +X127417000Y-95713000D01* +X127419000Y-95711000D01* +X127421000Y-95710000D01* +X127423000Y-95708000D01* +X127425000Y-95707000D01* +X127427000Y-95705000D01* +X127430000Y-95704000D01* +X127432000Y-95703000D01* +X127435000Y-95702000D01* +X127437000Y-95702000D01* +X127440000Y-95701000D01* +X127442000Y-95701000D01* +X127445000Y-95700000D01* +X127447000Y-95700000D01* +X127450000Y-95700000D01* +X127950000Y-95700000D01* +X127953000Y-95700000D01* +X127955000Y-95700000D01* +X127958000Y-95701000D01* +G37* +X128000000Y-96350000D02* +X128000000Y-96150000D01* +X128000000Y-96147000D01* +X128000000Y-96145000D01* +X127999000Y-96142000D01* +X127999000Y-96140000D01* +X127998000Y-96137000D01* +X127998000Y-96135000D01* +X127997000Y-96132000D01* +X127996000Y-96130000D01* +X127995000Y-96127000D01* +X127993000Y-96125000D01* +X127992000Y-96123000D01* +X127990000Y-96121000D01* +X127989000Y-96119000D01* +X127987000Y-96117000D01* +X127985000Y-96115000D01* +X127983000Y-96113000D01* +X127981000Y-96111000D01* +X127979000Y-96110000D01* +X127977000Y-96108000D01* +X127975000Y-96107000D01* +X127973000Y-96105000D01* +X127970000Y-96104000D01* +X127968000Y-96103000D01* +X127965000Y-96102000D01* +X127963000Y-96102000D01* +X127960000Y-96101000D01* +X127958000Y-96101000D01* +X127955000Y-96100000D01* +X127953000Y-96100000D01* +X127950000Y-96100000D01* +X127450000Y-96100000D01* +X127447000Y-96100000D01* +X127445000Y-96100000D01* +X127442000Y-96101000D01* +X127440000Y-96101000D01* +X127437000Y-96102000D01* +X127435000Y-96102000D01* +X127432000Y-96103000D01* +X127430000Y-96104000D01* +X127427000Y-96105000D01* +X127425000Y-96107000D01* +X127423000Y-96108000D01* +X127421000Y-96110000D01* +X127419000Y-96111000D01* +X127417000Y-96113000D01* +X127415000Y-96115000D01* +X127413000Y-96117000D01* +X127411000Y-96119000D01* +X127410000Y-96121000D01* +X127408000Y-96123000D01* +X127407000Y-96125000D01* +X127405000Y-96127000D01* +X127404000Y-96130000D01* +X127403000Y-96132000D01* +X127402000Y-96135000D01* +X127402000Y-96137000D01* +X127401000Y-96140000D01* +X127401000Y-96142000D01* +X127400000Y-96145000D01* +X127400000Y-96147000D01* +X127400000Y-96150000D01* +X127400000Y-96350000D01* +X127400000Y-96353000D01* +X127400000Y-96355000D01* +X127401000Y-96358000D01* +X127401000Y-96360000D01* +X127402000Y-96363000D01* +X127402000Y-96365000D01* +X127403000Y-96368000D01* +X127404000Y-96370000D01* +X127405000Y-96373000D01* +X127407000Y-96375000D01* +X127408000Y-96377000D01* +X127410000Y-96379000D01* +X127411000Y-96381000D01* +X127413000Y-96383000D01* +X127415000Y-96385000D01* +X127417000Y-96387000D01* +X127419000Y-96389000D01* +X127421000Y-96390000D01* +X127423000Y-96392000D01* +X127425000Y-96393000D01* +X127427000Y-96395000D01* +X127430000Y-96396000D01* +X127432000Y-96397000D01* +X127435000Y-96398000D01* +X127437000Y-96398000D01* +X127440000Y-96399000D01* +X127442000Y-96399000D01* +X127445000Y-96400000D01* +X127447000Y-96400000D01* +X127450000Y-96400000D01* +X127950000Y-96400000D01* +X127953000Y-96400000D01* +X127955000Y-96400000D01* +X127958000Y-96399000D01* +X127960000Y-96399000D01* +X127963000Y-96398000D01* +X127965000Y-96398000D01* +X127968000Y-96397000D01* +X127970000Y-96396000D01* +X127973000Y-96395000D01* +X127975000Y-96393000D01* +X127977000Y-96392000D01* +X127979000Y-96390000D01* +X127981000Y-96389000D01* +X127983000Y-96387000D01* +X127985000Y-96385000D01* +X127987000Y-96383000D01* +X127989000Y-96381000D01* +X127990000Y-96379000D01* +X127992000Y-96377000D01* +X127993000Y-96375000D01* +X127995000Y-96373000D01* +X127996000Y-96370000D01* +X127997000Y-96368000D01* +X127998000Y-96365000D01* +X127998000Y-96363000D01* +X127999000Y-96360000D01* +X127999000Y-96358000D01* +X128000000Y-96355000D01* +X128000000Y-96353000D01* +X128000000Y-96350000D01* +G36* +X127958000Y-96101000D02* +G01* +X127960000Y-96101000D01* +X127963000Y-96102000D01* +X127965000Y-96102000D01* +X127968000Y-96103000D01* +X127970000Y-96104000D01* +X127973000Y-96105000D01* +X127975000Y-96107000D01* +X127977000Y-96108000D01* +X127979000Y-96110000D01* +X127981000Y-96111000D01* +X127983000Y-96113000D01* +X127985000Y-96115000D01* +X127987000Y-96117000D01* +X127989000Y-96119000D01* +X127990000Y-96121000D01* +X127992000Y-96123000D01* +X127993000Y-96125000D01* +X127995000Y-96127000D01* +X127996000Y-96130000D01* +X127997000Y-96132000D01* +X127998000Y-96135000D01* +X127998000Y-96137000D01* +X127999000Y-96140000D01* +X127999000Y-96142000D01* +X128000000Y-96145000D01* +X128000000Y-96147000D01* +X128000000Y-96150000D01* +X128000000Y-96350000D01* +X128000000Y-96353000D01* +X128000000Y-96355000D01* +X127999000Y-96358000D01* +X127999000Y-96360000D01* +X127998000Y-96363000D01* +X127998000Y-96365000D01* +X127997000Y-96368000D01* +X127996000Y-96370000D01* +X127995000Y-96373000D01* +X127993000Y-96375000D01* +X127992000Y-96377000D01* +X127990000Y-96379000D01* +X127989000Y-96381000D01* +X127987000Y-96383000D01* +X127985000Y-96385000D01* +X127983000Y-96387000D01* +X127981000Y-96389000D01* +X127979000Y-96390000D01* +X127977000Y-96392000D01* +X127975000Y-96393000D01* +X127973000Y-96395000D01* +X127970000Y-96396000D01* +X127968000Y-96397000D01* +X127965000Y-96398000D01* +X127963000Y-96398000D01* +X127960000Y-96399000D01* +X127958000Y-96399000D01* +X127955000Y-96400000D01* +X127953000Y-96400000D01* +X127950000Y-96400000D01* +X127450000Y-96400000D01* +X127447000Y-96400000D01* +X127445000Y-96400000D01* +X127442000Y-96399000D01* +X127440000Y-96399000D01* +X127437000Y-96398000D01* +X127435000Y-96398000D01* +X127432000Y-96397000D01* +X127430000Y-96396000D01* +X127427000Y-96395000D01* +X127425000Y-96393000D01* +X127423000Y-96392000D01* +X127421000Y-96390000D01* +X127419000Y-96389000D01* +X127417000Y-96387000D01* +X127415000Y-96385000D01* +X127413000Y-96383000D01* +X127411000Y-96381000D01* +X127410000Y-96379000D01* +X127408000Y-96377000D01* +X127407000Y-96375000D01* +X127405000Y-96373000D01* +X127404000Y-96370000D01* +X127403000Y-96368000D01* +X127402000Y-96365000D01* +X127402000Y-96363000D01* +X127401000Y-96360000D01* +X127401000Y-96358000D01* +X127400000Y-96355000D01* +X127400000Y-96353000D01* +X127400000Y-96350000D01* +X127400000Y-96150000D01* +X127400000Y-96147000D01* +X127400000Y-96145000D01* +X127401000Y-96142000D01* +X127401000Y-96140000D01* +X127402000Y-96137000D01* +X127402000Y-96135000D01* +X127403000Y-96132000D01* +X127404000Y-96130000D01* +X127405000Y-96127000D01* +X127407000Y-96125000D01* +X127408000Y-96123000D01* +X127410000Y-96121000D01* +X127411000Y-96119000D01* +X127413000Y-96117000D01* +X127415000Y-96115000D01* +X127417000Y-96113000D01* +X127419000Y-96111000D01* +X127421000Y-96110000D01* +X127423000Y-96108000D01* +X127425000Y-96107000D01* +X127427000Y-96105000D01* +X127430000Y-96104000D01* +X127432000Y-96103000D01* +X127435000Y-96102000D01* +X127437000Y-96102000D01* +X127440000Y-96101000D01* +X127442000Y-96101000D01* +X127445000Y-96100000D01* +X127447000Y-96100000D01* +X127450000Y-96100000D01* +X127950000Y-96100000D01* +X127953000Y-96100000D01* +X127955000Y-96100000D01* +X127958000Y-96101000D01* +G37* +X128000000Y-96750000D02* +X128000000Y-96550000D01* +X128000000Y-96547000D01* +X128000000Y-96545000D01* +X127999000Y-96542000D01* +X127999000Y-96540000D01* +X127998000Y-96537000D01* +X127998000Y-96535000D01* +X127997000Y-96532000D01* +X127996000Y-96530000D01* +X127995000Y-96527000D01* +X127993000Y-96525000D01* +X127992000Y-96523000D01* +X127990000Y-96521000D01* +X127989000Y-96519000D01* +X127987000Y-96517000D01* +X127985000Y-96515000D01* +X127983000Y-96513000D01* +X127981000Y-96511000D01* +X127979000Y-96510000D01* +X127977000Y-96508000D01* +X127975000Y-96507000D01* +X127973000Y-96505000D01* +X127970000Y-96504000D01* +X127968000Y-96503000D01* +X127965000Y-96502000D01* +X127963000Y-96502000D01* +X127960000Y-96501000D01* +X127958000Y-96501000D01* +X127955000Y-96500000D01* +X127953000Y-96500000D01* +X127950000Y-96500000D01* +X127450000Y-96500000D01* +X127447000Y-96500000D01* +X127445000Y-96500000D01* +X127442000Y-96501000D01* +X127440000Y-96501000D01* +X127437000Y-96502000D01* +X127435000Y-96502000D01* +X127432000Y-96503000D01* +X127430000Y-96504000D01* +X127427000Y-96505000D01* +X127425000Y-96507000D01* +X127423000Y-96508000D01* +X127421000Y-96510000D01* +X127419000Y-96511000D01* +X127417000Y-96513000D01* +X127415000Y-96515000D01* +X127413000Y-96517000D01* +X127411000Y-96519000D01* +X127410000Y-96521000D01* +X127408000Y-96523000D01* +X127407000Y-96525000D01* +X127405000Y-96527000D01* +X127404000Y-96530000D01* +X127403000Y-96532000D01* +X127402000Y-96535000D01* +X127402000Y-96537000D01* +X127401000Y-96540000D01* +X127401000Y-96542000D01* +X127400000Y-96545000D01* +X127400000Y-96547000D01* +X127400000Y-96550000D01* +X127400000Y-96750000D01* +X127400000Y-96753000D01* +X127400000Y-96755000D01* +X127401000Y-96758000D01* +X127401000Y-96760000D01* +X127402000Y-96763000D01* +X127402000Y-96765000D01* +X127403000Y-96768000D01* +X127404000Y-96770000D01* +X127405000Y-96773000D01* +X127407000Y-96775000D01* +X127408000Y-96777000D01* +X127410000Y-96779000D01* +X127411000Y-96781000D01* +X127413000Y-96783000D01* +X127415000Y-96785000D01* +X127417000Y-96787000D01* +X127419000Y-96789000D01* +X127421000Y-96790000D01* +X127423000Y-96792000D01* +X127425000Y-96793000D01* +X127427000Y-96795000D01* +X127430000Y-96796000D01* +X127432000Y-96797000D01* +X127435000Y-96798000D01* +X127437000Y-96798000D01* +X127440000Y-96799000D01* +X127442000Y-96799000D01* +X127445000Y-96800000D01* +X127447000Y-96800000D01* +X127450000Y-96800000D01* +X127950000Y-96800000D01* +X127953000Y-96800000D01* +X127955000Y-96800000D01* +X127958000Y-96799000D01* +X127960000Y-96799000D01* +X127963000Y-96798000D01* +X127965000Y-96798000D01* +X127968000Y-96797000D01* +X127970000Y-96796000D01* +X127973000Y-96795000D01* +X127975000Y-96793000D01* +X127977000Y-96792000D01* +X127979000Y-96790000D01* +X127981000Y-96789000D01* +X127983000Y-96787000D01* +X127985000Y-96785000D01* +X127987000Y-96783000D01* +X127989000Y-96781000D01* +X127990000Y-96779000D01* +X127992000Y-96777000D01* +X127993000Y-96775000D01* +X127995000Y-96773000D01* +X127996000Y-96770000D01* +X127997000Y-96768000D01* +X127998000Y-96765000D01* +X127998000Y-96763000D01* +X127999000Y-96760000D01* +X127999000Y-96758000D01* +X128000000Y-96755000D01* +X128000000Y-96753000D01* +X128000000Y-96750000D01* +G36* +X127958000Y-96501000D02* +G01* +X127960000Y-96501000D01* +X127963000Y-96502000D01* +X127965000Y-96502000D01* +X127968000Y-96503000D01* +X127970000Y-96504000D01* +X127973000Y-96505000D01* +X127975000Y-96507000D01* +X127977000Y-96508000D01* +X127979000Y-96510000D01* +X127981000Y-96511000D01* +X127983000Y-96513000D01* +X127985000Y-96515000D01* +X127987000Y-96517000D01* +X127989000Y-96519000D01* +X127990000Y-96521000D01* +X127992000Y-96523000D01* +X127993000Y-96525000D01* +X127995000Y-96527000D01* +X127996000Y-96530000D01* +X127997000Y-96532000D01* +X127998000Y-96535000D01* +X127998000Y-96537000D01* +X127999000Y-96540000D01* +X127999000Y-96542000D01* +X128000000Y-96545000D01* +X128000000Y-96547000D01* +X128000000Y-96550000D01* +X128000000Y-96750000D01* +X128000000Y-96753000D01* +X128000000Y-96755000D01* +X127999000Y-96758000D01* +X127999000Y-96760000D01* +X127998000Y-96763000D01* +X127998000Y-96765000D01* +X127997000Y-96768000D01* +X127996000Y-96770000D01* +X127995000Y-96773000D01* +X127993000Y-96775000D01* +X127992000Y-96777000D01* +X127990000Y-96779000D01* +X127989000Y-96781000D01* +X127987000Y-96783000D01* +X127985000Y-96785000D01* +X127983000Y-96787000D01* +X127981000Y-96789000D01* +X127979000Y-96790000D01* +X127977000Y-96792000D01* +X127975000Y-96793000D01* +X127973000Y-96795000D01* +X127970000Y-96796000D01* +X127968000Y-96797000D01* +X127965000Y-96798000D01* +X127963000Y-96798000D01* +X127960000Y-96799000D01* +X127958000Y-96799000D01* +X127955000Y-96800000D01* +X127953000Y-96800000D01* +X127950000Y-96800000D01* +X127450000Y-96800000D01* +X127447000Y-96800000D01* +X127445000Y-96800000D01* +X127442000Y-96799000D01* +X127440000Y-96799000D01* +X127437000Y-96798000D01* +X127435000Y-96798000D01* +X127432000Y-96797000D01* +X127430000Y-96796000D01* +X127427000Y-96795000D01* +X127425000Y-96793000D01* +X127423000Y-96792000D01* +X127421000Y-96790000D01* +X127419000Y-96789000D01* +X127417000Y-96787000D01* +X127415000Y-96785000D01* +X127413000Y-96783000D01* +X127411000Y-96781000D01* +X127410000Y-96779000D01* +X127408000Y-96777000D01* +X127407000Y-96775000D01* +X127405000Y-96773000D01* +X127404000Y-96770000D01* +X127403000Y-96768000D01* +X127402000Y-96765000D01* +X127402000Y-96763000D01* +X127401000Y-96760000D01* +X127401000Y-96758000D01* +X127400000Y-96755000D01* +X127400000Y-96753000D01* +X127400000Y-96750000D01* +X127400000Y-96550000D01* +X127400000Y-96547000D01* +X127400000Y-96545000D01* +X127401000Y-96542000D01* +X127401000Y-96540000D01* +X127402000Y-96537000D01* +X127402000Y-96535000D01* +X127403000Y-96532000D01* +X127404000Y-96530000D01* +X127405000Y-96527000D01* +X127407000Y-96525000D01* +X127408000Y-96523000D01* +X127410000Y-96521000D01* +X127411000Y-96519000D01* +X127413000Y-96517000D01* +X127415000Y-96515000D01* +X127417000Y-96513000D01* +X127419000Y-96511000D01* +X127421000Y-96510000D01* +X127423000Y-96508000D01* +X127425000Y-96507000D01* +X127427000Y-96505000D01* +X127430000Y-96504000D01* +X127432000Y-96503000D01* +X127435000Y-96502000D01* +X127437000Y-96502000D01* +X127440000Y-96501000D01* +X127442000Y-96501000D01* +X127445000Y-96500000D01* +X127447000Y-96500000D01* +X127450000Y-96500000D01* +X127950000Y-96500000D01* +X127953000Y-96500000D01* +X127955000Y-96500000D01* +X127958000Y-96501000D01* +G37* +X128000000Y-97150000D02* +X128000000Y-96950000D01* +X128000000Y-96947000D01* +X128000000Y-96945000D01* +X127999000Y-96942000D01* +X127999000Y-96940000D01* +X127998000Y-96937000D01* +X127998000Y-96935000D01* +X127997000Y-96932000D01* +X127996000Y-96930000D01* +X127995000Y-96927000D01* +X127993000Y-96925000D01* +X127992000Y-96923000D01* +X127990000Y-96921000D01* +X127989000Y-96919000D01* +X127987000Y-96917000D01* +X127985000Y-96915000D01* +X127983000Y-96913000D01* +X127981000Y-96911000D01* +X127979000Y-96910000D01* +X127977000Y-96908000D01* +X127975000Y-96907000D01* +X127973000Y-96905000D01* +X127970000Y-96904000D01* +X127968000Y-96903000D01* +X127965000Y-96902000D01* +X127963000Y-96902000D01* +X127960000Y-96901000D01* +X127958000Y-96901000D01* +X127955000Y-96900000D01* +X127953000Y-96900000D01* +X127950000Y-96900000D01* +X127450000Y-96900000D01* +X127447000Y-96900000D01* +X127445000Y-96900000D01* +X127442000Y-96901000D01* +X127440000Y-96901000D01* +X127437000Y-96902000D01* +X127435000Y-96902000D01* +X127432000Y-96903000D01* +X127430000Y-96904000D01* +X127427000Y-96905000D01* +X127425000Y-96907000D01* +X127423000Y-96908000D01* +X127421000Y-96910000D01* +X127419000Y-96911000D01* +X127417000Y-96913000D01* +X127415000Y-96915000D01* +X127413000Y-96917000D01* +X127411000Y-96919000D01* +X127410000Y-96921000D01* +X127408000Y-96923000D01* +X127407000Y-96925000D01* +X127405000Y-96927000D01* +X127404000Y-96930000D01* +X127403000Y-96932000D01* +X127402000Y-96935000D01* +X127402000Y-96937000D01* +X127401000Y-96940000D01* +X127401000Y-96942000D01* +X127400000Y-96945000D01* +X127400000Y-96947000D01* +X127400000Y-96950000D01* +X127400000Y-97150000D01* +X127400000Y-97153000D01* +X127400000Y-97155000D01* +X127401000Y-97158000D01* +X127401000Y-97160000D01* +X127402000Y-97163000D01* +X127402000Y-97165000D01* +X127403000Y-97168000D01* +X127404000Y-97170000D01* +X127405000Y-97173000D01* +X127407000Y-97175000D01* +X127408000Y-97177000D01* +X127410000Y-97179000D01* +X127411000Y-97181000D01* +X127413000Y-97183000D01* +X127415000Y-97185000D01* +X127417000Y-97187000D01* +X127419000Y-97189000D01* +X127421000Y-97190000D01* +X127423000Y-97192000D01* +X127425000Y-97193000D01* +X127427000Y-97195000D01* +X127430000Y-97196000D01* +X127432000Y-97197000D01* +X127435000Y-97198000D01* +X127437000Y-97198000D01* +X127440000Y-97199000D01* +X127442000Y-97199000D01* +X127445000Y-97200000D01* +X127447000Y-97200000D01* +X127450000Y-97200000D01* +X127950000Y-97200000D01* +X127953000Y-97200000D01* +X127955000Y-97200000D01* +X127958000Y-97199000D01* +X127960000Y-97199000D01* +X127963000Y-97198000D01* +X127965000Y-97198000D01* +X127968000Y-97197000D01* +X127970000Y-97196000D01* +X127973000Y-97195000D01* +X127975000Y-97193000D01* +X127977000Y-97192000D01* +X127979000Y-97190000D01* +X127981000Y-97189000D01* +X127983000Y-97187000D01* +X127985000Y-97185000D01* +X127987000Y-97183000D01* +X127989000Y-97181000D01* +X127990000Y-97179000D01* +X127992000Y-97177000D01* +X127993000Y-97175000D01* +X127995000Y-97173000D01* +X127996000Y-97170000D01* +X127997000Y-97168000D01* +X127998000Y-97165000D01* +X127998000Y-97163000D01* +X127999000Y-97160000D01* +X127999000Y-97158000D01* +X128000000Y-97155000D01* +X128000000Y-97153000D01* +X128000000Y-97150000D01* +G36* +X127958000Y-96901000D02* +G01* +X127960000Y-96901000D01* +X127963000Y-96902000D01* +X127965000Y-96902000D01* +X127968000Y-96903000D01* +X127970000Y-96904000D01* +X127973000Y-96905000D01* +X127975000Y-96907000D01* +X127977000Y-96908000D01* +X127979000Y-96910000D01* +X127981000Y-96911000D01* +X127983000Y-96913000D01* +X127985000Y-96915000D01* +X127987000Y-96917000D01* +X127989000Y-96919000D01* +X127990000Y-96921000D01* +X127992000Y-96923000D01* +X127993000Y-96925000D01* +X127995000Y-96927000D01* +X127996000Y-96930000D01* +X127997000Y-96932000D01* +X127998000Y-96935000D01* +X127998000Y-96937000D01* +X127999000Y-96940000D01* +X127999000Y-96942000D01* +X128000000Y-96945000D01* +X128000000Y-96947000D01* +X128000000Y-96950000D01* +X128000000Y-97150000D01* +X128000000Y-97153000D01* +X128000000Y-97155000D01* +X127999000Y-97158000D01* +X127999000Y-97160000D01* +X127998000Y-97163000D01* +X127998000Y-97165000D01* +X127997000Y-97168000D01* +X127996000Y-97170000D01* +X127995000Y-97173000D01* +X127993000Y-97175000D01* +X127992000Y-97177000D01* +X127990000Y-97179000D01* +X127989000Y-97181000D01* +X127987000Y-97183000D01* +X127985000Y-97185000D01* +X127983000Y-97187000D01* +X127981000Y-97189000D01* +X127979000Y-97190000D01* +X127977000Y-97192000D01* +X127975000Y-97193000D01* +X127973000Y-97195000D01* +X127970000Y-97196000D01* +X127968000Y-97197000D01* +X127965000Y-97198000D01* +X127963000Y-97198000D01* +X127960000Y-97199000D01* +X127958000Y-97199000D01* +X127955000Y-97200000D01* +X127953000Y-97200000D01* +X127950000Y-97200000D01* +X127450000Y-97200000D01* +X127447000Y-97200000D01* +X127445000Y-97200000D01* +X127442000Y-97199000D01* +X127440000Y-97199000D01* +X127437000Y-97198000D01* +X127435000Y-97198000D01* +X127432000Y-97197000D01* +X127430000Y-97196000D01* +X127427000Y-97195000D01* +X127425000Y-97193000D01* +X127423000Y-97192000D01* +X127421000Y-97190000D01* +X127419000Y-97189000D01* +X127417000Y-97187000D01* +X127415000Y-97185000D01* +X127413000Y-97183000D01* +X127411000Y-97181000D01* +X127410000Y-97179000D01* +X127408000Y-97177000D01* +X127407000Y-97175000D01* +X127405000Y-97173000D01* +X127404000Y-97170000D01* +X127403000Y-97168000D01* +X127402000Y-97165000D01* +X127402000Y-97163000D01* +X127401000Y-97160000D01* +X127401000Y-97158000D01* +X127400000Y-97155000D01* +X127400000Y-97153000D01* +X127400000Y-97150000D01* +X127400000Y-96950000D01* +X127400000Y-96947000D01* +X127400000Y-96945000D01* +X127401000Y-96942000D01* +X127401000Y-96940000D01* +X127402000Y-96937000D01* +X127402000Y-96935000D01* +X127403000Y-96932000D01* +X127404000Y-96930000D01* +X127405000Y-96927000D01* +X127407000Y-96925000D01* +X127408000Y-96923000D01* +X127410000Y-96921000D01* +X127411000Y-96919000D01* +X127413000Y-96917000D01* +X127415000Y-96915000D01* +X127417000Y-96913000D01* +X127419000Y-96911000D01* +X127421000Y-96910000D01* +X127423000Y-96908000D01* +X127425000Y-96907000D01* +X127427000Y-96905000D01* +X127430000Y-96904000D01* +X127432000Y-96903000D01* +X127435000Y-96902000D01* +X127437000Y-96902000D01* +X127440000Y-96901000D01* +X127442000Y-96901000D01* +X127445000Y-96900000D01* +X127447000Y-96900000D01* +X127450000Y-96900000D01* +X127950000Y-96900000D01* +X127953000Y-96900000D01* +X127955000Y-96900000D01* +X127958000Y-96901000D01* +G37* +X129250000Y-96950000D02* +X129250000Y-95550000D01* +X129250000Y-95545000D01* +X129249000Y-95540000D01* +X129249000Y-95534000D01* +X129248000Y-95529000D01* +X129247000Y-95524000D01* +X129245000Y-95519000D01* +X129243000Y-95514000D01* +X129241000Y-95509000D01* +X129239000Y-95505000D01* +X129237000Y-95500000D01* +X129234000Y-95496000D01* +X129231000Y-95491000D01* +X129228000Y-95487000D01* +X129224000Y-95483000D01* +X129221000Y-95479000D01* +X129217000Y-95476000D01* +X129213000Y-95472000D01* +X129209000Y-95469000D01* +X129204000Y-95466000D01* +X129200000Y-95463000D01* +X129195000Y-95461000D01* +X129191000Y-95459000D01* +X129186000Y-95457000D01* +X129181000Y-95455000D01* +X129176000Y-95453000D01* +X129171000Y-95452000D01* +X129166000Y-95451000D01* +X129160000Y-95451000D01* +X129155000Y-95450000D01* +X129150000Y-95450000D01* +X128350000Y-95450000D01* +X128345000Y-95450000D01* +X128340000Y-95451000D01* +X128334000Y-95451000D01* +X128329000Y-95452000D01* +X128324000Y-95453000D01* +X128319000Y-95455000D01* +X128314000Y-95457000D01* +X128309000Y-95459000D01* +X128305000Y-95461000D01* +X128300000Y-95463000D01* +X128296000Y-95466000D01* +X128291000Y-95469000D01* +X128287000Y-95472000D01* +X128283000Y-95476000D01* +X128279000Y-95479000D01* +X128276000Y-95483000D01* +X128272000Y-95487000D01* +X128269000Y-95491000D01* +X128266000Y-95496000D01* +X128263000Y-95500000D01* +X128261000Y-95505000D01* +X128259000Y-95509000D01* +X128257000Y-95514000D01* +X128255000Y-95519000D01* +X128253000Y-95524000D01* +X128252000Y-95529000D01* +X128251000Y-95534000D01* +X128251000Y-95540000D01* +X128250000Y-95545000D01* +X128250000Y-95550000D01* +X128250000Y-96950000D01* +X128250000Y-96955000D01* +X128251000Y-96960000D01* +X128251000Y-96966000D01* +X128252000Y-96971000D01* +X128253000Y-96976000D01* +X128255000Y-96981000D01* +X128257000Y-96986000D01* +X128259000Y-96991000D01* +X128261000Y-96995000D01* +X128263000Y-97000000D01* +X128266000Y-97004000D01* +X128269000Y-97009000D01* +X128272000Y-97013000D01* +X128276000Y-97017000D01* +X128279000Y-97021000D01* +X128283000Y-97024000D01* +X128287000Y-97028000D01* +X128291000Y-97031000D01* +X128296000Y-97034000D01* +X128300000Y-97037000D01* +X128305000Y-97039000D01* +X128309000Y-97041000D01* +X128314000Y-97043000D01* +X128319000Y-97045000D01* +X128324000Y-97047000D01* +X128329000Y-97048000D01* +X128334000Y-97049000D01* +X128340000Y-97049000D01* +X128345000Y-97050000D01* +X128350000Y-97050000D01* +X129150000Y-97050000D01* +X129155000Y-97050000D01* +X129160000Y-97049000D01* +X129166000Y-97049000D01* +X129171000Y-97048000D01* +X129176000Y-97047000D01* +X129181000Y-97045000D01* +X129186000Y-97043000D01* +X129191000Y-97041000D01* +X129195000Y-97039000D01* +X129200000Y-97037000D01* +X129204000Y-97034000D01* +X129209000Y-97031000D01* +X129213000Y-97028000D01* +X129217000Y-97024000D01* +X129221000Y-97021000D01* +X129224000Y-97017000D01* +X129228000Y-97013000D01* +X129231000Y-97009000D01* +X129234000Y-97004000D01* +X129237000Y-97000000D01* +X129239000Y-96995000D01* +X129241000Y-96991000D01* +X129243000Y-96986000D01* +X129245000Y-96981000D01* +X129247000Y-96976000D01* +X129248000Y-96971000D01* +X129249000Y-96966000D01* +X129249000Y-96960000D01* +X129250000Y-96955000D01* +X129250000Y-96950000D01* +G36* +X129160000Y-95451000D02* +G01* +X129166000Y-95451000D01* +X129171000Y-95452000D01* +X129176000Y-95453000D01* +X129181000Y-95455000D01* +X129186000Y-95457000D01* +X129191000Y-95459000D01* +X129195000Y-95461000D01* +X129200000Y-95463000D01* +X129204000Y-95466000D01* +X129209000Y-95469000D01* +X129213000Y-95472000D01* +X129217000Y-95476000D01* +X129221000Y-95479000D01* +X129224000Y-95483000D01* +X129228000Y-95487000D01* +X129231000Y-95491000D01* +X129234000Y-95496000D01* +X129237000Y-95500000D01* +X129239000Y-95505000D01* +X129241000Y-95509000D01* +X129243000Y-95514000D01* +X129245000Y-95519000D01* +X129247000Y-95524000D01* +X129248000Y-95529000D01* +X129249000Y-95534000D01* +X129249000Y-95540000D01* +X129250000Y-95545000D01* +X129250000Y-95550000D01* +X129250000Y-96950000D01* +X129250000Y-96955000D01* +X129249000Y-96960000D01* +X129249000Y-96966000D01* +X129248000Y-96971000D01* +X129247000Y-96976000D01* +X129245000Y-96981000D01* +X129243000Y-96986000D01* +X129241000Y-96991000D01* +X129239000Y-96995000D01* +X129237000Y-97000000D01* +X129234000Y-97004000D01* +X129231000Y-97009000D01* +X129228000Y-97013000D01* +X129224000Y-97017000D01* +X129221000Y-97021000D01* +X129217000Y-97024000D01* +X129213000Y-97028000D01* +X129209000Y-97031000D01* +X129204000Y-97034000D01* +X129200000Y-97037000D01* +X129195000Y-97039000D01* +X129191000Y-97041000D01* +X129186000Y-97043000D01* +X129181000Y-97045000D01* +X129176000Y-97047000D01* +X129171000Y-97048000D01* +X129166000Y-97049000D01* +X129160000Y-97049000D01* +X129155000Y-97050000D01* +X129150000Y-97050000D01* +X128350000Y-97050000D01* +X128345000Y-97050000D01* +X128340000Y-97049000D01* +X128334000Y-97049000D01* +X128329000Y-97048000D01* +X128324000Y-97047000D01* +X128319000Y-97045000D01* +X128314000Y-97043000D01* +X128309000Y-97041000D01* +X128305000Y-97039000D01* +X128300000Y-97037000D01* +X128296000Y-97034000D01* +X128291000Y-97031000D01* +X128287000Y-97028000D01* +X128283000Y-97024000D01* +X128279000Y-97021000D01* +X128276000Y-97017000D01* +X128272000Y-97013000D01* +X128269000Y-97009000D01* +X128266000Y-97004000D01* +X128263000Y-97000000D01* +X128261000Y-96995000D01* +X128259000Y-96991000D01* +X128257000Y-96986000D01* +X128255000Y-96981000D01* +X128253000Y-96976000D01* +X128252000Y-96971000D01* +X128251000Y-96966000D01* +X128251000Y-96960000D01* +X128250000Y-96955000D01* +X128250000Y-96950000D01* +X128250000Y-95550000D01* +X128250000Y-95545000D01* +X128251000Y-95540000D01* +X128251000Y-95534000D01* +X128252000Y-95529000D01* +X128253000Y-95524000D01* +X128255000Y-95519000D01* +X128257000Y-95514000D01* +X128259000Y-95509000D01* +X128261000Y-95505000D01* +X128263000Y-95500000D01* +X128266000Y-95496000D01* +X128269000Y-95491000D01* +X128272000Y-95487000D01* +X128276000Y-95483000D01* +X128279000Y-95479000D01* +X128283000Y-95476000D01* +X128287000Y-95472000D01* +X128291000Y-95469000D01* +X128296000Y-95466000D01* +X128300000Y-95463000D01* +X128305000Y-95461000D01* +X128309000Y-95459000D01* +X128314000Y-95457000D01* +X128319000Y-95455000D01* +X128324000Y-95453000D01* +X128329000Y-95452000D01* +X128334000Y-95451000D01* +X128340000Y-95451000D01* +X128345000Y-95450000D01* +X128350000Y-95450000D01* +X129150000Y-95450000D01* +X129155000Y-95450000D01* +X129160000Y-95451000D01* +G37* +X130100000Y-95550000D02* +X130100000Y-95350000D01* +X130100000Y-95347000D01* +X130100000Y-95345000D01* +X130099000Y-95342000D01* +X130099000Y-95340000D01* +X130098000Y-95337000D01* +X130098000Y-95335000D01* +X130097000Y-95332000D01* +X130096000Y-95330000D01* +X130095000Y-95327000D01* +X130093000Y-95325000D01* +X130092000Y-95323000D01* +X130090000Y-95321000D01* +X130089000Y-95319000D01* +X130087000Y-95317000D01* +X130085000Y-95315000D01* +X130083000Y-95313000D01* +X130081000Y-95311000D01* +X130079000Y-95310000D01* +X130077000Y-95308000D01* +X130075000Y-95307000D01* +X130073000Y-95305000D01* +X130070000Y-95304000D01* +X130068000Y-95303000D01* +X130065000Y-95302000D01* +X130063000Y-95302000D01* +X130060000Y-95301000D01* +X130058000Y-95301000D01* +X130055000Y-95300000D01* +X130053000Y-95300000D01* +X130050000Y-95300000D01* +X129550000Y-95300000D01* +X129547000Y-95300000D01* +X129545000Y-95300000D01* +X129542000Y-95301000D01* +X129540000Y-95301000D01* +X129537000Y-95302000D01* +X129535000Y-95302000D01* +X129532000Y-95303000D01* +X129530000Y-95304000D01* +X129527000Y-95305000D01* +X129525000Y-95307000D01* +X129523000Y-95308000D01* +X129521000Y-95310000D01* +X129519000Y-95311000D01* +X129517000Y-95313000D01* +X129515000Y-95315000D01* +X129513000Y-95317000D01* +X129511000Y-95319000D01* +X129510000Y-95321000D01* +X129508000Y-95323000D01* +X129507000Y-95325000D01* +X129505000Y-95327000D01* +X129504000Y-95330000D01* +X129503000Y-95332000D01* +X129502000Y-95335000D01* +X129502000Y-95337000D01* +X129501000Y-95340000D01* +X129501000Y-95342000D01* +X129500000Y-95345000D01* +X129500000Y-95347000D01* +X129500000Y-95350000D01* +X129500000Y-95550000D01* +X129500000Y-95553000D01* +X129500000Y-95555000D01* +X129501000Y-95558000D01* +X129501000Y-95560000D01* +X129502000Y-95563000D01* +X129502000Y-95565000D01* +X129503000Y-95568000D01* +X129504000Y-95570000D01* +X129505000Y-95573000D01* +X129507000Y-95575000D01* +X129508000Y-95577000D01* +X129510000Y-95579000D01* +X129511000Y-95581000D01* +X129513000Y-95583000D01* +X129515000Y-95585000D01* +X129517000Y-95587000D01* +X129519000Y-95589000D01* +X129521000Y-95590000D01* +X129523000Y-95592000D01* +X129525000Y-95593000D01* +X129527000Y-95595000D01* +X129530000Y-95596000D01* +X129532000Y-95597000D01* +X129535000Y-95598000D01* +X129537000Y-95598000D01* +X129540000Y-95599000D01* +X129542000Y-95599000D01* +X129545000Y-95600000D01* +X129547000Y-95600000D01* +X129550000Y-95600000D01* +X130050000Y-95600000D01* +X130053000Y-95600000D01* +X130055000Y-95600000D01* +X130058000Y-95599000D01* +X130060000Y-95599000D01* +X130063000Y-95598000D01* +X130065000Y-95598000D01* +X130068000Y-95597000D01* +X130070000Y-95596000D01* +X130073000Y-95595000D01* +X130075000Y-95593000D01* +X130077000Y-95592000D01* +X130079000Y-95590000D01* +X130081000Y-95589000D01* +X130083000Y-95587000D01* +X130085000Y-95585000D01* +X130087000Y-95583000D01* +X130089000Y-95581000D01* +X130090000Y-95579000D01* +X130092000Y-95577000D01* +X130093000Y-95575000D01* +X130095000Y-95573000D01* +X130096000Y-95570000D01* +X130097000Y-95568000D01* +X130098000Y-95565000D01* +X130098000Y-95563000D01* +X130099000Y-95560000D01* +X130099000Y-95558000D01* +X130100000Y-95555000D01* +X130100000Y-95553000D01* +X130100000Y-95550000D01* +G36* +X130058000Y-95301000D02* +G01* +X130060000Y-95301000D01* +X130063000Y-95302000D01* +X130065000Y-95302000D01* +X130068000Y-95303000D01* +X130070000Y-95304000D01* +X130073000Y-95305000D01* +X130075000Y-95307000D01* +X130077000Y-95308000D01* +X130079000Y-95310000D01* +X130081000Y-95311000D01* +X130083000Y-95313000D01* +X130085000Y-95315000D01* +X130087000Y-95317000D01* +X130089000Y-95319000D01* +X130090000Y-95321000D01* +X130092000Y-95323000D01* +X130093000Y-95325000D01* +X130095000Y-95327000D01* +X130096000Y-95330000D01* +X130097000Y-95332000D01* +X130098000Y-95335000D01* +X130098000Y-95337000D01* +X130099000Y-95340000D01* +X130099000Y-95342000D01* +X130100000Y-95345000D01* +X130100000Y-95347000D01* +X130100000Y-95350000D01* +X130100000Y-95550000D01* +X130100000Y-95553000D01* +X130100000Y-95555000D01* +X130099000Y-95558000D01* +X130099000Y-95560000D01* +X130098000Y-95563000D01* +X130098000Y-95565000D01* +X130097000Y-95568000D01* +X130096000Y-95570000D01* +X130095000Y-95573000D01* +X130093000Y-95575000D01* +X130092000Y-95577000D01* +X130090000Y-95579000D01* +X130089000Y-95581000D01* +X130087000Y-95583000D01* +X130085000Y-95585000D01* +X130083000Y-95587000D01* +X130081000Y-95589000D01* +X130079000Y-95590000D01* +X130077000Y-95592000D01* +X130075000Y-95593000D01* +X130073000Y-95595000D01* +X130070000Y-95596000D01* +X130068000Y-95597000D01* +X130065000Y-95598000D01* +X130063000Y-95598000D01* +X130060000Y-95599000D01* +X130058000Y-95599000D01* +X130055000Y-95600000D01* +X130053000Y-95600000D01* +X130050000Y-95600000D01* +X129550000Y-95600000D01* +X129547000Y-95600000D01* +X129545000Y-95600000D01* +X129542000Y-95599000D01* +X129540000Y-95599000D01* +X129537000Y-95598000D01* +X129535000Y-95598000D01* +X129532000Y-95597000D01* +X129530000Y-95596000D01* +X129527000Y-95595000D01* +X129525000Y-95593000D01* +X129523000Y-95592000D01* +X129521000Y-95590000D01* +X129519000Y-95589000D01* +X129517000Y-95587000D01* +X129515000Y-95585000D01* +X129513000Y-95583000D01* +X129511000Y-95581000D01* +X129510000Y-95579000D01* +X129508000Y-95577000D01* +X129507000Y-95575000D01* +X129505000Y-95573000D01* +X129504000Y-95570000D01* +X129503000Y-95568000D01* +X129502000Y-95565000D01* +X129502000Y-95563000D01* +X129501000Y-95560000D01* +X129501000Y-95558000D01* +X129500000Y-95555000D01* +X129500000Y-95553000D01* +X129500000Y-95550000D01* +X129500000Y-95350000D01* +X129500000Y-95347000D01* +X129500000Y-95345000D01* +X129501000Y-95342000D01* +X129501000Y-95340000D01* +X129502000Y-95337000D01* +X129502000Y-95335000D01* +X129503000Y-95332000D01* +X129504000Y-95330000D01* +X129505000Y-95327000D01* +X129507000Y-95325000D01* +X129508000Y-95323000D01* +X129510000Y-95321000D01* +X129511000Y-95319000D01* +X129513000Y-95317000D01* +X129515000Y-95315000D01* +X129517000Y-95313000D01* +X129519000Y-95311000D01* +X129521000Y-95310000D01* +X129523000Y-95308000D01* +X129525000Y-95307000D01* +X129527000Y-95305000D01* +X129530000Y-95304000D01* +X129532000Y-95303000D01* +X129535000Y-95302000D01* +X129537000Y-95302000D01* +X129540000Y-95301000D01* +X129542000Y-95301000D01* +X129545000Y-95300000D01* +X129547000Y-95300000D01* +X129550000Y-95300000D01* +X130050000Y-95300000D01* +X130053000Y-95300000D01* +X130055000Y-95300000D01* +X130058000Y-95301000D01* +G37* +X130100000Y-95950000D02* +X130100000Y-95750000D01* +X130100000Y-95747000D01* +X130100000Y-95745000D01* +X130099000Y-95742000D01* +X130099000Y-95740000D01* +X130098000Y-95737000D01* +X130098000Y-95735000D01* +X130097000Y-95732000D01* +X130096000Y-95730000D01* +X130095000Y-95727000D01* +X130093000Y-95725000D01* +X130092000Y-95723000D01* +X130090000Y-95721000D01* +X130089000Y-95719000D01* +X130087000Y-95717000D01* +X130085000Y-95715000D01* +X130083000Y-95713000D01* +X130081000Y-95711000D01* +X130079000Y-95710000D01* +X130077000Y-95708000D01* +X130075000Y-95707000D01* +X130073000Y-95705000D01* +X130070000Y-95704000D01* +X130068000Y-95703000D01* +X130065000Y-95702000D01* +X130063000Y-95702000D01* +X130060000Y-95701000D01* +X130058000Y-95701000D01* +X130055000Y-95700000D01* +X130053000Y-95700000D01* +X130050000Y-95700000D01* +X129550000Y-95700000D01* +X129547000Y-95700000D01* +X129545000Y-95700000D01* +X129542000Y-95701000D01* +X129540000Y-95701000D01* +X129537000Y-95702000D01* +X129535000Y-95702000D01* +X129532000Y-95703000D01* +X129530000Y-95704000D01* +X129527000Y-95705000D01* +X129525000Y-95707000D01* +X129523000Y-95708000D01* +X129521000Y-95710000D01* +X129519000Y-95711000D01* +X129517000Y-95713000D01* +X129515000Y-95715000D01* +X129513000Y-95717000D01* +X129511000Y-95719000D01* +X129510000Y-95721000D01* +X129508000Y-95723000D01* +X129507000Y-95725000D01* +X129505000Y-95727000D01* +X129504000Y-95730000D01* +X129503000Y-95732000D01* +X129502000Y-95735000D01* +X129502000Y-95737000D01* +X129501000Y-95740000D01* +X129501000Y-95742000D01* +X129500000Y-95745000D01* +X129500000Y-95747000D01* +X129500000Y-95750000D01* +X129500000Y-95950000D01* +X129500000Y-95953000D01* +X129500000Y-95955000D01* +X129501000Y-95958000D01* +X129501000Y-95960000D01* +X129502000Y-95963000D01* +X129502000Y-95965000D01* +X129503000Y-95968000D01* +X129504000Y-95970000D01* +X129505000Y-95973000D01* +X129507000Y-95975000D01* +X129508000Y-95977000D01* +X129510000Y-95979000D01* +X129511000Y-95981000D01* +X129513000Y-95983000D01* +X129515000Y-95985000D01* +X129517000Y-95987000D01* +X129519000Y-95989000D01* +X129521000Y-95990000D01* +X129523000Y-95992000D01* +X129525000Y-95993000D01* +X129527000Y-95995000D01* +X129530000Y-95996000D01* +X129532000Y-95997000D01* +X129535000Y-95998000D01* +X129537000Y-95998000D01* +X129540000Y-95999000D01* +X129542000Y-95999000D01* +X129545000Y-96000000D01* +X129547000Y-96000000D01* +X129550000Y-96000000D01* +X130050000Y-96000000D01* +X130053000Y-96000000D01* +X130055000Y-96000000D01* +X130058000Y-95999000D01* +X130060000Y-95999000D01* +X130063000Y-95998000D01* +X130065000Y-95998000D01* +X130068000Y-95997000D01* +X130070000Y-95996000D01* +X130073000Y-95995000D01* +X130075000Y-95993000D01* +X130077000Y-95992000D01* +X130079000Y-95990000D01* +X130081000Y-95989000D01* +X130083000Y-95987000D01* +X130085000Y-95985000D01* +X130087000Y-95983000D01* +X130089000Y-95981000D01* +X130090000Y-95979000D01* +X130092000Y-95977000D01* +X130093000Y-95975000D01* +X130095000Y-95973000D01* +X130096000Y-95970000D01* +X130097000Y-95968000D01* +X130098000Y-95965000D01* +X130098000Y-95963000D01* +X130099000Y-95960000D01* +X130099000Y-95958000D01* +X130100000Y-95955000D01* +X130100000Y-95953000D01* +X130100000Y-95950000D01* +G36* +X130058000Y-95701000D02* +G01* +X130060000Y-95701000D01* +X130063000Y-95702000D01* +X130065000Y-95702000D01* +X130068000Y-95703000D01* +X130070000Y-95704000D01* +X130073000Y-95705000D01* +X130075000Y-95707000D01* +X130077000Y-95708000D01* +X130079000Y-95710000D01* +X130081000Y-95711000D01* +X130083000Y-95713000D01* +X130085000Y-95715000D01* +X130087000Y-95717000D01* +X130089000Y-95719000D01* +X130090000Y-95721000D01* +X130092000Y-95723000D01* +X130093000Y-95725000D01* +X130095000Y-95727000D01* +X130096000Y-95730000D01* +X130097000Y-95732000D01* +X130098000Y-95735000D01* +X130098000Y-95737000D01* +X130099000Y-95740000D01* +X130099000Y-95742000D01* +X130100000Y-95745000D01* +X130100000Y-95747000D01* +X130100000Y-95750000D01* +X130100000Y-95950000D01* +X130100000Y-95953000D01* +X130100000Y-95955000D01* +X130099000Y-95958000D01* +X130099000Y-95960000D01* +X130098000Y-95963000D01* +X130098000Y-95965000D01* +X130097000Y-95968000D01* +X130096000Y-95970000D01* +X130095000Y-95973000D01* +X130093000Y-95975000D01* +X130092000Y-95977000D01* +X130090000Y-95979000D01* +X130089000Y-95981000D01* +X130087000Y-95983000D01* +X130085000Y-95985000D01* +X130083000Y-95987000D01* +X130081000Y-95989000D01* +X130079000Y-95990000D01* +X130077000Y-95992000D01* +X130075000Y-95993000D01* +X130073000Y-95995000D01* +X130070000Y-95996000D01* +X130068000Y-95997000D01* +X130065000Y-95998000D01* +X130063000Y-95998000D01* +X130060000Y-95999000D01* +X130058000Y-95999000D01* +X130055000Y-96000000D01* +X130053000Y-96000000D01* +X130050000Y-96000000D01* +X129550000Y-96000000D01* +X129547000Y-96000000D01* +X129545000Y-96000000D01* +X129542000Y-95999000D01* +X129540000Y-95999000D01* +X129537000Y-95998000D01* +X129535000Y-95998000D01* +X129532000Y-95997000D01* +X129530000Y-95996000D01* +X129527000Y-95995000D01* +X129525000Y-95993000D01* +X129523000Y-95992000D01* +X129521000Y-95990000D01* +X129519000Y-95989000D01* +X129517000Y-95987000D01* +X129515000Y-95985000D01* +X129513000Y-95983000D01* +X129511000Y-95981000D01* +X129510000Y-95979000D01* +X129508000Y-95977000D01* +X129507000Y-95975000D01* +X129505000Y-95973000D01* +X129504000Y-95970000D01* +X129503000Y-95968000D01* +X129502000Y-95965000D01* +X129502000Y-95963000D01* +X129501000Y-95960000D01* +X129501000Y-95958000D01* +X129500000Y-95955000D01* +X129500000Y-95953000D01* +X129500000Y-95950000D01* +X129500000Y-95750000D01* +X129500000Y-95747000D01* +X129500000Y-95745000D01* +X129501000Y-95742000D01* +X129501000Y-95740000D01* +X129502000Y-95737000D01* +X129502000Y-95735000D01* +X129503000Y-95732000D01* +X129504000Y-95730000D01* +X129505000Y-95727000D01* +X129507000Y-95725000D01* +X129508000Y-95723000D01* +X129510000Y-95721000D01* +X129511000Y-95719000D01* +X129513000Y-95717000D01* +X129515000Y-95715000D01* +X129517000Y-95713000D01* +X129519000Y-95711000D01* +X129521000Y-95710000D01* +X129523000Y-95708000D01* +X129525000Y-95707000D01* +X129527000Y-95705000D01* +X129530000Y-95704000D01* +X129532000Y-95703000D01* +X129535000Y-95702000D01* +X129537000Y-95702000D01* +X129540000Y-95701000D01* +X129542000Y-95701000D01* +X129545000Y-95700000D01* +X129547000Y-95700000D01* +X129550000Y-95700000D01* +X130050000Y-95700000D01* +X130053000Y-95700000D01* +X130055000Y-95700000D01* +X130058000Y-95701000D01* +G37* +X130100000Y-96350000D02* +X130100000Y-96150000D01* +X130100000Y-96147000D01* +X130100000Y-96145000D01* +X130099000Y-96142000D01* +X130099000Y-96140000D01* +X130098000Y-96137000D01* +X130098000Y-96135000D01* +X130097000Y-96132000D01* +X130096000Y-96130000D01* +X130095000Y-96127000D01* +X130093000Y-96125000D01* +X130092000Y-96123000D01* +X130090000Y-96121000D01* +X130089000Y-96119000D01* +X130087000Y-96117000D01* +X130085000Y-96115000D01* +X130083000Y-96113000D01* +X130081000Y-96111000D01* +X130079000Y-96110000D01* +X130077000Y-96108000D01* +X130075000Y-96107000D01* +X130073000Y-96105000D01* +X130070000Y-96104000D01* +X130068000Y-96103000D01* +X130065000Y-96102000D01* +X130063000Y-96102000D01* +X130060000Y-96101000D01* +X130058000Y-96101000D01* +X130055000Y-96100000D01* +X130053000Y-96100000D01* +X130050000Y-96100000D01* +X129550000Y-96100000D01* +X129547000Y-96100000D01* +X129545000Y-96100000D01* +X129542000Y-96101000D01* +X129540000Y-96101000D01* +X129537000Y-96102000D01* +X129535000Y-96102000D01* +X129532000Y-96103000D01* +X129530000Y-96104000D01* +X129527000Y-96105000D01* +X129525000Y-96107000D01* +X129523000Y-96108000D01* +X129521000Y-96110000D01* +X129519000Y-96111000D01* +X129517000Y-96113000D01* +X129515000Y-96115000D01* +X129513000Y-96117000D01* +X129511000Y-96119000D01* +X129510000Y-96121000D01* +X129508000Y-96123000D01* +X129507000Y-96125000D01* +X129505000Y-96127000D01* +X129504000Y-96130000D01* +X129503000Y-96132000D01* +X129502000Y-96135000D01* +X129502000Y-96137000D01* +X129501000Y-96140000D01* +X129501000Y-96142000D01* +X129500000Y-96145000D01* +X129500000Y-96147000D01* +X129500000Y-96150000D01* +X129500000Y-96350000D01* +X129500000Y-96353000D01* +X129500000Y-96355000D01* +X129501000Y-96358000D01* +X129501000Y-96360000D01* +X129502000Y-96363000D01* +X129502000Y-96365000D01* +X129503000Y-96368000D01* +X129504000Y-96370000D01* +X129505000Y-96373000D01* +X129507000Y-96375000D01* +X129508000Y-96377000D01* +X129510000Y-96379000D01* +X129511000Y-96381000D01* +X129513000Y-96383000D01* +X129515000Y-96385000D01* +X129517000Y-96387000D01* +X129519000Y-96389000D01* +X129521000Y-96390000D01* +X129523000Y-96392000D01* +X129525000Y-96393000D01* +X129527000Y-96395000D01* +X129530000Y-96396000D01* +X129532000Y-96397000D01* +X129535000Y-96398000D01* +X129537000Y-96398000D01* +X129540000Y-96399000D01* +X129542000Y-96399000D01* +X129545000Y-96400000D01* +X129547000Y-96400000D01* +X129550000Y-96400000D01* +X130050000Y-96400000D01* +X130053000Y-96400000D01* +X130055000Y-96400000D01* +X130058000Y-96399000D01* +X130060000Y-96399000D01* +X130063000Y-96398000D01* +X130065000Y-96398000D01* +X130068000Y-96397000D01* +X130070000Y-96396000D01* +X130073000Y-96395000D01* +X130075000Y-96393000D01* +X130077000Y-96392000D01* +X130079000Y-96390000D01* +X130081000Y-96389000D01* +X130083000Y-96387000D01* +X130085000Y-96385000D01* +X130087000Y-96383000D01* +X130089000Y-96381000D01* +X130090000Y-96379000D01* +X130092000Y-96377000D01* +X130093000Y-96375000D01* +X130095000Y-96373000D01* +X130096000Y-96370000D01* +X130097000Y-96368000D01* +X130098000Y-96365000D01* +X130098000Y-96363000D01* +X130099000Y-96360000D01* +X130099000Y-96358000D01* +X130100000Y-96355000D01* +X130100000Y-96353000D01* +X130100000Y-96350000D01* +G36* +X130058000Y-96101000D02* +G01* +X130060000Y-96101000D01* +X130063000Y-96102000D01* +X130065000Y-96102000D01* +X130068000Y-96103000D01* +X130070000Y-96104000D01* +X130073000Y-96105000D01* +X130075000Y-96107000D01* +X130077000Y-96108000D01* +X130079000Y-96110000D01* +X130081000Y-96111000D01* +X130083000Y-96113000D01* +X130085000Y-96115000D01* +X130087000Y-96117000D01* +X130089000Y-96119000D01* +X130090000Y-96121000D01* +X130092000Y-96123000D01* +X130093000Y-96125000D01* +X130095000Y-96127000D01* +X130096000Y-96130000D01* +X130097000Y-96132000D01* +X130098000Y-96135000D01* +X130098000Y-96137000D01* +X130099000Y-96140000D01* +X130099000Y-96142000D01* +X130100000Y-96145000D01* +X130100000Y-96147000D01* +X130100000Y-96150000D01* +X130100000Y-96350000D01* +X130100000Y-96353000D01* +X130100000Y-96355000D01* +X130099000Y-96358000D01* +X130099000Y-96360000D01* +X130098000Y-96363000D01* +X130098000Y-96365000D01* +X130097000Y-96368000D01* +X130096000Y-96370000D01* +X130095000Y-96373000D01* +X130093000Y-96375000D01* +X130092000Y-96377000D01* +X130090000Y-96379000D01* +X130089000Y-96381000D01* +X130087000Y-96383000D01* +X130085000Y-96385000D01* +X130083000Y-96387000D01* +X130081000Y-96389000D01* +X130079000Y-96390000D01* +X130077000Y-96392000D01* +X130075000Y-96393000D01* +X130073000Y-96395000D01* +X130070000Y-96396000D01* +X130068000Y-96397000D01* +X130065000Y-96398000D01* +X130063000Y-96398000D01* +X130060000Y-96399000D01* +X130058000Y-96399000D01* +X130055000Y-96400000D01* +X130053000Y-96400000D01* +X130050000Y-96400000D01* +X129550000Y-96400000D01* +X129547000Y-96400000D01* +X129545000Y-96400000D01* +X129542000Y-96399000D01* +X129540000Y-96399000D01* +X129537000Y-96398000D01* +X129535000Y-96398000D01* +X129532000Y-96397000D01* +X129530000Y-96396000D01* +X129527000Y-96395000D01* +X129525000Y-96393000D01* +X129523000Y-96392000D01* +X129521000Y-96390000D01* +X129519000Y-96389000D01* +X129517000Y-96387000D01* +X129515000Y-96385000D01* +X129513000Y-96383000D01* +X129511000Y-96381000D01* +X129510000Y-96379000D01* +X129508000Y-96377000D01* +X129507000Y-96375000D01* +X129505000Y-96373000D01* +X129504000Y-96370000D01* +X129503000Y-96368000D01* +X129502000Y-96365000D01* +X129502000Y-96363000D01* +X129501000Y-96360000D01* +X129501000Y-96358000D01* +X129500000Y-96355000D01* +X129500000Y-96353000D01* +X129500000Y-96350000D01* +X129500000Y-96150000D01* +X129500000Y-96147000D01* +X129500000Y-96145000D01* +X129501000Y-96142000D01* +X129501000Y-96140000D01* +X129502000Y-96137000D01* +X129502000Y-96135000D01* +X129503000Y-96132000D01* +X129504000Y-96130000D01* +X129505000Y-96127000D01* +X129507000Y-96125000D01* +X129508000Y-96123000D01* +X129510000Y-96121000D01* +X129511000Y-96119000D01* +X129513000Y-96117000D01* +X129515000Y-96115000D01* +X129517000Y-96113000D01* +X129519000Y-96111000D01* +X129521000Y-96110000D01* +X129523000Y-96108000D01* +X129525000Y-96107000D01* +X129527000Y-96105000D01* +X129530000Y-96104000D01* +X129532000Y-96103000D01* +X129535000Y-96102000D01* +X129537000Y-96102000D01* +X129540000Y-96101000D01* +X129542000Y-96101000D01* +X129545000Y-96100000D01* +X129547000Y-96100000D01* +X129550000Y-96100000D01* +X130050000Y-96100000D01* +X130053000Y-96100000D01* +X130055000Y-96100000D01* +X130058000Y-96101000D01* +G37* +X130100000Y-96750000D02* +X130100000Y-96550000D01* +X130100000Y-96547000D01* +X130100000Y-96545000D01* +X130099000Y-96542000D01* +X130099000Y-96540000D01* +X130098000Y-96537000D01* +X130098000Y-96535000D01* +X130097000Y-96532000D01* +X130096000Y-96530000D01* +X130095000Y-96527000D01* +X130093000Y-96525000D01* +X130092000Y-96523000D01* +X130090000Y-96521000D01* +X130089000Y-96519000D01* +X130087000Y-96517000D01* +X130085000Y-96515000D01* +X130083000Y-96513000D01* +X130081000Y-96511000D01* +X130079000Y-96510000D01* +X130077000Y-96508000D01* +X130075000Y-96507000D01* +X130073000Y-96505000D01* +X130070000Y-96504000D01* +X130068000Y-96503000D01* +X130065000Y-96502000D01* +X130063000Y-96502000D01* +X130060000Y-96501000D01* +X130058000Y-96501000D01* +X130055000Y-96500000D01* +X130053000Y-96500000D01* +X130050000Y-96500000D01* +X129550000Y-96500000D01* +X129547000Y-96500000D01* +X129545000Y-96500000D01* +X129542000Y-96501000D01* +X129540000Y-96501000D01* +X129537000Y-96502000D01* +X129535000Y-96502000D01* +X129532000Y-96503000D01* +X129530000Y-96504000D01* +X129527000Y-96505000D01* +X129525000Y-96507000D01* +X129523000Y-96508000D01* +X129521000Y-96510000D01* +X129519000Y-96511000D01* +X129517000Y-96513000D01* +X129515000Y-96515000D01* +X129513000Y-96517000D01* +X129511000Y-96519000D01* +X129510000Y-96521000D01* +X129508000Y-96523000D01* +X129507000Y-96525000D01* +X129505000Y-96527000D01* +X129504000Y-96530000D01* +X129503000Y-96532000D01* +X129502000Y-96535000D01* +X129502000Y-96537000D01* +X129501000Y-96540000D01* +X129501000Y-96542000D01* +X129500000Y-96545000D01* +X129500000Y-96547000D01* +X129500000Y-96550000D01* +X129500000Y-96750000D01* +X129500000Y-96753000D01* +X129500000Y-96755000D01* +X129501000Y-96758000D01* +X129501000Y-96760000D01* +X129502000Y-96763000D01* +X129502000Y-96765000D01* +X129503000Y-96768000D01* +X129504000Y-96770000D01* +X129505000Y-96773000D01* +X129507000Y-96775000D01* +X129508000Y-96777000D01* +X129510000Y-96779000D01* +X129511000Y-96781000D01* +X129513000Y-96783000D01* +X129515000Y-96785000D01* +X129517000Y-96787000D01* +X129519000Y-96789000D01* +X129521000Y-96790000D01* +X129523000Y-96792000D01* +X129525000Y-96793000D01* +X129527000Y-96795000D01* +X129530000Y-96796000D01* +X129532000Y-96797000D01* +X129535000Y-96798000D01* +X129537000Y-96798000D01* +X129540000Y-96799000D01* +X129542000Y-96799000D01* +X129545000Y-96800000D01* +X129547000Y-96800000D01* +X129550000Y-96800000D01* +X130050000Y-96800000D01* +X130053000Y-96800000D01* +X130055000Y-96800000D01* +X130058000Y-96799000D01* +X130060000Y-96799000D01* +X130063000Y-96798000D01* +X130065000Y-96798000D01* +X130068000Y-96797000D01* +X130070000Y-96796000D01* +X130073000Y-96795000D01* +X130075000Y-96793000D01* +X130077000Y-96792000D01* +X130079000Y-96790000D01* +X130081000Y-96789000D01* +X130083000Y-96787000D01* +X130085000Y-96785000D01* +X130087000Y-96783000D01* +X130089000Y-96781000D01* +X130090000Y-96779000D01* +X130092000Y-96777000D01* +X130093000Y-96775000D01* +X130095000Y-96773000D01* +X130096000Y-96770000D01* +X130097000Y-96768000D01* +X130098000Y-96765000D01* +X130098000Y-96763000D01* +X130099000Y-96760000D01* +X130099000Y-96758000D01* +X130100000Y-96755000D01* +X130100000Y-96753000D01* +X130100000Y-96750000D01* +G36* +X130058000Y-96501000D02* +G01* +X130060000Y-96501000D01* +X130063000Y-96502000D01* +X130065000Y-96502000D01* +X130068000Y-96503000D01* +X130070000Y-96504000D01* +X130073000Y-96505000D01* +X130075000Y-96507000D01* +X130077000Y-96508000D01* +X130079000Y-96510000D01* +X130081000Y-96511000D01* +X130083000Y-96513000D01* +X130085000Y-96515000D01* +X130087000Y-96517000D01* +X130089000Y-96519000D01* +X130090000Y-96521000D01* +X130092000Y-96523000D01* +X130093000Y-96525000D01* +X130095000Y-96527000D01* +X130096000Y-96530000D01* +X130097000Y-96532000D01* +X130098000Y-96535000D01* +X130098000Y-96537000D01* +X130099000Y-96540000D01* +X130099000Y-96542000D01* +X130100000Y-96545000D01* +X130100000Y-96547000D01* +X130100000Y-96550000D01* +X130100000Y-96750000D01* +X130100000Y-96753000D01* +X130100000Y-96755000D01* +X130099000Y-96758000D01* +X130099000Y-96760000D01* +X130098000Y-96763000D01* +X130098000Y-96765000D01* +X130097000Y-96768000D01* +X130096000Y-96770000D01* +X130095000Y-96773000D01* +X130093000Y-96775000D01* +X130092000Y-96777000D01* +X130090000Y-96779000D01* +X130089000Y-96781000D01* +X130087000Y-96783000D01* +X130085000Y-96785000D01* +X130083000Y-96787000D01* +X130081000Y-96789000D01* +X130079000Y-96790000D01* +X130077000Y-96792000D01* +X130075000Y-96793000D01* +X130073000Y-96795000D01* +X130070000Y-96796000D01* +X130068000Y-96797000D01* +X130065000Y-96798000D01* +X130063000Y-96798000D01* +X130060000Y-96799000D01* +X130058000Y-96799000D01* +X130055000Y-96800000D01* +X130053000Y-96800000D01* +X130050000Y-96800000D01* +X129550000Y-96800000D01* +X129547000Y-96800000D01* +X129545000Y-96800000D01* +X129542000Y-96799000D01* +X129540000Y-96799000D01* +X129537000Y-96798000D01* +X129535000Y-96798000D01* +X129532000Y-96797000D01* +X129530000Y-96796000D01* +X129527000Y-96795000D01* +X129525000Y-96793000D01* +X129523000Y-96792000D01* +X129521000Y-96790000D01* +X129519000Y-96789000D01* +X129517000Y-96787000D01* +X129515000Y-96785000D01* +X129513000Y-96783000D01* +X129511000Y-96781000D01* +X129510000Y-96779000D01* +X129508000Y-96777000D01* +X129507000Y-96775000D01* +X129505000Y-96773000D01* +X129504000Y-96770000D01* +X129503000Y-96768000D01* +X129502000Y-96765000D01* +X129502000Y-96763000D01* +X129501000Y-96760000D01* +X129501000Y-96758000D01* +X129500000Y-96755000D01* +X129500000Y-96753000D01* +X129500000Y-96750000D01* +X129500000Y-96550000D01* +X129500000Y-96547000D01* +X129500000Y-96545000D01* +X129501000Y-96542000D01* +X129501000Y-96540000D01* +X129502000Y-96537000D01* +X129502000Y-96535000D01* +X129503000Y-96532000D01* +X129504000Y-96530000D01* +X129505000Y-96527000D01* +X129507000Y-96525000D01* +X129508000Y-96523000D01* +X129510000Y-96521000D01* +X129511000Y-96519000D01* +X129513000Y-96517000D01* +X129515000Y-96515000D01* +X129517000Y-96513000D01* +X129519000Y-96511000D01* +X129521000Y-96510000D01* +X129523000Y-96508000D01* +X129525000Y-96507000D01* +X129527000Y-96505000D01* +X129530000Y-96504000D01* +X129532000Y-96503000D01* +X129535000Y-96502000D01* +X129537000Y-96502000D01* +X129540000Y-96501000D01* +X129542000Y-96501000D01* +X129545000Y-96500000D01* +X129547000Y-96500000D01* +X129550000Y-96500000D01* +X130050000Y-96500000D01* +X130053000Y-96500000D01* +X130055000Y-96500000D01* +X130058000Y-96501000D01* +G37* +X130100000Y-97150000D02* +X130100000Y-96950000D01* +X130100000Y-96947000D01* +X130100000Y-96945000D01* +X130099000Y-96942000D01* +X130099000Y-96940000D01* +X130098000Y-96937000D01* +X130098000Y-96935000D01* +X130097000Y-96932000D01* +X130096000Y-96930000D01* +X130095000Y-96927000D01* +X130093000Y-96925000D01* +X130092000Y-96923000D01* +X130090000Y-96921000D01* +X130089000Y-96919000D01* +X130087000Y-96917000D01* +X130085000Y-96915000D01* +X130083000Y-96913000D01* +X130081000Y-96911000D01* +X130079000Y-96910000D01* +X130077000Y-96908000D01* +X130075000Y-96907000D01* +X130073000Y-96905000D01* +X130070000Y-96904000D01* +X130068000Y-96903000D01* +X130065000Y-96902000D01* +X130063000Y-96902000D01* +X130060000Y-96901000D01* +X130058000Y-96901000D01* +X130055000Y-96900000D01* +X130053000Y-96900000D01* +X130050000Y-96900000D01* +X129550000Y-96900000D01* +X129547000Y-96900000D01* +X129545000Y-96900000D01* +X129542000Y-96901000D01* +X129540000Y-96901000D01* +X129537000Y-96902000D01* +X129535000Y-96902000D01* +X129532000Y-96903000D01* +X129530000Y-96904000D01* +X129527000Y-96905000D01* +X129525000Y-96907000D01* +X129523000Y-96908000D01* +X129521000Y-96910000D01* +X129519000Y-96911000D01* +X129517000Y-96913000D01* +X129515000Y-96915000D01* +X129513000Y-96917000D01* +X129511000Y-96919000D01* +X129510000Y-96921000D01* +X129508000Y-96923000D01* +X129507000Y-96925000D01* +X129505000Y-96927000D01* +X129504000Y-96930000D01* +X129503000Y-96932000D01* +X129502000Y-96935000D01* +X129502000Y-96937000D01* +X129501000Y-96940000D01* +X129501000Y-96942000D01* +X129500000Y-96945000D01* +X129500000Y-96947000D01* +X129500000Y-96950000D01* +X129500000Y-97150000D01* +X129500000Y-97153000D01* +X129500000Y-97155000D01* +X129501000Y-97158000D01* +X129501000Y-97160000D01* +X129502000Y-97163000D01* +X129502000Y-97165000D01* +X129503000Y-97168000D01* +X129504000Y-97170000D01* +X129505000Y-97173000D01* +X129507000Y-97175000D01* +X129508000Y-97177000D01* +X129510000Y-97179000D01* +X129511000Y-97181000D01* +X129513000Y-97183000D01* +X129515000Y-97185000D01* +X129517000Y-97187000D01* +X129519000Y-97189000D01* +X129521000Y-97190000D01* +X129523000Y-97192000D01* +X129525000Y-97193000D01* +X129527000Y-97195000D01* +X129530000Y-97196000D01* +X129532000Y-97197000D01* +X129535000Y-97198000D01* +X129537000Y-97198000D01* +X129540000Y-97199000D01* +X129542000Y-97199000D01* +X129545000Y-97200000D01* +X129547000Y-97200000D01* +X129550000Y-97200000D01* +X130050000Y-97200000D01* +X130053000Y-97200000D01* +X130055000Y-97200000D01* +X130058000Y-97199000D01* +X130060000Y-97199000D01* +X130063000Y-97198000D01* +X130065000Y-97198000D01* +X130068000Y-97197000D01* +X130070000Y-97196000D01* +X130073000Y-97195000D01* +X130075000Y-97193000D01* +X130077000Y-97192000D01* +X130079000Y-97190000D01* +X130081000Y-97189000D01* +X130083000Y-97187000D01* +X130085000Y-97185000D01* +X130087000Y-97183000D01* +X130089000Y-97181000D01* +X130090000Y-97179000D01* +X130092000Y-97177000D01* +X130093000Y-97175000D01* +X130095000Y-97173000D01* +X130096000Y-97170000D01* +X130097000Y-97168000D01* +X130098000Y-97165000D01* +X130098000Y-97163000D01* +X130099000Y-97160000D01* +X130099000Y-97158000D01* +X130100000Y-97155000D01* +X130100000Y-97153000D01* +X130100000Y-97150000D01* +G36* +X130058000Y-96901000D02* +G01* +X130060000Y-96901000D01* +X130063000Y-96902000D01* +X130065000Y-96902000D01* +X130068000Y-96903000D01* +X130070000Y-96904000D01* +X130073000Y-96905000D01* +X130075000Y-96907000D01* +X130077000Y-96908000D01* +X130079000Y-96910000D01* +X130081000Y-96911000D01* +X130083000Y-96913000D01* +X130085000Y-96915000D01* +X130087000Y-96917000D01* +X130089000Y-96919000D01* +X130090000Y-96921000D01* +X130092000Y-96923000D01* +X130093000Y-96925000D01* +X130095000Y-96927000D01* +X130096000Y-96930000D01* +X130097000Y-96932000D01* +X130098000Y-96935000D01* +X130098000Y-96937000D01* +X130099000Y-96940000D01* +X130099000Y-96942000D01* +X130100000Y-96945000D01* +X130100000Y-96947000D01* +X130100000Y-96950000D01* +X130100000Y-97150000D01* +X130100000Y-97153000D01* +X130100000Y-97155000D01* +X130099000Y-97158000D01* +X130099000Y-97160000D01* +X130098000Y-97163000D01* +X130098000Y-97165000D01* +X130097000Y-97168000D01* +X130096000Y-97170000D01* +X130095000Y-97173000D01* +X130093000Y-97175000D01* +X130092000Y-97177000D01* +X130090000Y-97179000D01* +X130089000Y-97181000D01* +X130087000Y-97183000D01* +X130085000Y-97185000D01* +X130083000Y-97187000D01* +X130081000Y-97189000D01* +X130079000Y-97190000D01* +X130077000Y-97192000D01* +X130075000Y-97193000D01* +X130073000Y-97195000D01* +X130070000Y-97196000D01* +X130068000Y-97197000D01* +X130065000Y-97198000D01* +X130063000Y-97198000D01* +X130060000Y-97199000D01* +X130058000Y-97199000D01* +X130055000Y-97200000D01* +X130053000Y-97200000D01* +X130050000Y-97200000D01* +X129550000Y-97200000D01* +X129547000Y-97200000D01* +X129545000Y-97200000D01* +X129542000Y-97199000D01* +X129540000Y-97199000D01* +X129537000Y-97198000D01* +X129535000Y-97198000D01* +X129532000Y-97197000D01* +X129530000Y-97196000D01* +X129527000Y-97195000D01* +X129525000Y-97193000D01* +X129523000Y-97192000D01* +X129521000Y-97190000D01* +X129519000Y-97189000D01* +X129517000Y-97187000D01* +X129515000Y-97185000D01* +X129513000Y-97183000D01* +X129511000Y-97181000D01* +X129510000Y-97179000D01* +X129508000Y-97177000D01* +X129507000Y-97175000D01* +X129505000Y-97173000D01* +X129504000Y-97170000D01* +X129503000Y-97168000D01* +X129502000Y-97165000D01* +X129502000Y-97163000D01* +X129501000Y-97160000D01* +X129501000Y-97158000D01* +X129500000Y-97155000D01* +X129500000Y-97153000D01* +X129500000Y-97150000D01* +X129500000Y-96950000D01* +X129500000Y-96947000D01* +X129500000Y-96945000D01* +X129501000Y-96942000D01* +X129501000Y-96940000D01* +X129502000Y-96937000D01* +X129502000Y-96935000D01* +X129503000Y-96932000D01* +X129504000Y-96930000D01* +X129505000Y-96927000D01* +X129507000Y-96925000D01* +X129508000Y-96923000D01* +X129510000Y-96921000D01* +X129511000Y-96919000D01* +X129513000Y-96917000D01* +X129515000Y-96915000D01* +X129517000Y-96913000D01* +X129519000Y-96911000D01* +X129521000Y-96910000D01* +X129523000Y-96908000D01* +X129525000Y-96907000D01* +X129527000Y-96905000D01* +X129530000Y-96904000D01* +X129532000Y-96903000D01* +X129535000Y-96902000D01* +X129537000Y-96902000D01* +X129540000Y-96901000D01* +X129542000Y-96901000D01* +X129545000Y-96900000D01* +X129547000Y-96900000D01* +X129550000Y-96900000D01* +X130050000Y-96900000D01* +X130053000Y-96900000D01* +X130055000Y-96900000D01* +X130058000Y-96901000D01* +G37* +%TD*% +D11* %TO.C,SW_THR_UP1*% X121800000Y-71375000D03* X121800000Y-75625000D03* %TD*% -D11* +D12* %TO.C,MH1*% X122500000Y-62600000D03* %TD*% %TO.C,MH4*% X147000000Y-127000000D03* %TD*% -D10* +D11* %TO.C,SW_VOL_DN1*% X148200000Y-85625000D03* X148200000Y-81375000D03* %TD*% -D12* +D13* %TO.C,J_USB1*% X134110000Y-124550000D03* X139890000Y-124550000D03* -D13* -X132680000Y-124020000D03* D14* +X132680000Y-124020000D03* +D15* X132680000Y-128200000D03* -D13* -X141320000Y-124020000D03* D14* +X141320000Y-124020000D03* +D15* X141320000Y-128200000D03* %TD*% -D15* +D16* %TO.C,J_STICK1*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D16* +D17* X137500000Y-69770000D03* X143730000Y-81000000D03* X135000000Y-69770000D03* X143730000Y-78500000D03* X132500000Y-69770000D03* X143730000Y-76000000D03* -D17* +D18* X131750000Y-84250000D03* X138250000Y-84250000D03* X131750000Y-88750000D03* X138250000Y-88750000D03* %TD*% -D11* +D12* %TO.C,MH2*% X147400000Y-62800000D03* %TD*% -D10* +D11* %TO.C,SW_THR_DN1*% X121800000Y-81375000D03* X121800000Y-85625000D03* @@ -139,136 +2921,134 @@ X148200000Y-71375000D03* X120875000Y-127900000D03* X125125000Y-127900000D03* %TD*% -D11* +D12* %TO.C,MH3*% X123000000Y-122500000D03* %TD*% -D18* +D19* %TO.C,R_BTN_PU1*% -X124900000Y-94600000D03* -X125920000Y-94600000D03* +X127381250Y-93764999D03* +X126361250Y-93764999D03* %TD*% -D19* +D20* +%TO.C,C_SYS_1*% +X133750000Y-94250000D03* +X135650000Y-94250000D03* +%TD*% +D21* %TO.C,Q_PWR1*% X137335000Y-77065000D03* X139235000Y-77065000D03* X138285000Y-78940000D03* %TD*% -D20* -%TO.C,C_VBUS1*% -X140500000Y-89525000D03* -X140500000Y-87975000D03* -%TD*% -D21* +D22* %TO.C,D_VBUS_TVS1*% X135845000Y-126245000D03* X137945000Y-126245000D03* %TD*% -D22* +D23* %TO.C,BT1*% X145200000Y-123100000D03* -D23* +D24* X147200000Y-123100000D03* %TD*% -D24* +D25* %TO.C,FID4*% X145000000Y-61750000D03* %TD*% -D25* -%TO.C,C_OLED_1*% -X123575000Y-107800000D03* -X122025000Y-107800000D03* +D26* +%TO.C,C_VIN_2*% +X125750000Y-95290000D03* +X125750000Y-96250000D03* %TD*% -D24* +D27* +%TO.C,C_VIN_1*% +X123750000Y-95250000D03* +X121850000Y-95250000D03* +%TD*% +D25* %TO.C,FID6*% X144500000Y-128250000D03* %TD*% -D26* +D28* +%TO.C,C_BUCK_OUT1*% +X138025000Y-94800000D03* +X138025000Y-96700000D03* +%TD*% +D29* %TO.C,D_INV_ISO1*% X124661300Y-90740000D03* X125961300Y-90740000D03* X125311300Y-92515000D03* %TD*% -D27* +D30* %TO.C,D_OR1*% X130135000Y-78690000D03* X126835000Y-78690000D03* %TD*% -D18* +D31* %TO.C,R_PWR_EN_PD1*% X140425000Y-80240000D03* X141445000Y-80240000D03* %TD*% -D24* +D25* %TO.C,FID5*% X122750000Y-128250000D03* %TD*% -D28* -%TO.C,SW_BOOT1*% -X144100000Y-106950000D03* -X148250000Y-106950000D03* -X144100000Y-104800000D03* -X148250000Y-104800000D03* -%TD*% -D29* -%TO.C,C_TRIG1*% -X131980000Y-91750000D03* -X131020000Y-91750000D03* -%TD*% -D30* -%TO.C,FB_RF1*% -X139037500Y-91375000D03* -X140612500Y-91375000D03* -%TD*% -D31* -%TO.C,U_IMU1*% -X145862500Y-67050000D03* -X145862500Y-67550000D03* -X145862500Y-68050000D03* -X145862500Y-68550000D03* D32* -X145200000Y-68712500D03* -X144700000Y-68712500D03* -X144200000Y-68712500D03* -D31* -X143537500Y-68550000D03* -X143537500Y-68050000D03* -X143537500Y-67550000D03* -X143537500Y-67050000D03* +%TO.C,U_IMU1*% +X129062500Y-126100000D03* +X129562500Y-126100000D03* +X130062500Y-126100000D03* +X130562500Y-126100000D03* +D33* +X130725000Y-126762500D03* +X130725000Y-127262500D03* +X130725000Y-127762500D03* D32* -X144200000Y-66887500D03* -X144700000Y-66887500D03* -X145200000Y-66887500D03* +X130562500Y-128425000D03* +X130062500Y-128425000D03* +X129562500Y-128425000D03* +X129062500Y-128425000D03* +D33* +X128900000Y-127762500D03* +X128900000Y-127262500D03* +X128900000Y-126762500D03* %TD*% -D29* +D34* +%TO.C,C_BUCK_IN1*% +X146500000Y-91550000D03* +X146500000Y-89650000D03* +%TD*% +D35* %TO.C,C_LATCH_G1*% X135485000Y-74890000D03* X134525000Y-74890000D03* %TD*% -D33* +D36* %TO.C,C_HALL1*% -X128320000Y-64600000D03* -X129280000Y-64600000D03* +X128940000Y-63800000D03* +X129900000Y-63800000D03* %TD*% -D34* +D19* %TO.C,R_INV_BASE1*% X125881300Y-88965000D03* X124861300Y-88965000D03* %TD*% -D10* +D11* %TO.C,SW_TRIG_DIG1*% X132875000Y-61800000D03* X137125000Y-61800000D03* -D35* +D37* X133775000Y-62700000D03* X136225000Y-62700000D03* -D36* +D38* X135000000Y-62700000D03* -D37* +D39* X133150000Y-60750000D03* X136850000Y-60750000D03* %TD*% -D38* +D40* %TO.C,R_INV_PU1*% X128461300Y-91725000D03* X128461300Y-90705000D03* @@ -277,203 +3057,138 @@ X128461300Y-90705000D03* X140785000Y-76960000D03* X140785000Y-75940000D03* %TD*% -D19* +D21* %TO.C,Q_LATCH1*% X133385000Y-76940000D03* X135285000Y-76940000D03* X134335000Y-78815000D03* %TD*% -D39* -%TO.C,J_SWD1*% -X146300000Y-114775000D03* -X145284000Y-109695000D03* -X147316000Y-109695000D03* -D40* -X145665000Y-113505000D03* -X146935000Y-113505000D03* -X145665000Y-112235000D03* -X146935000Y-112235000D03* -X145665000Y-110965000D03* -X146935000Y-110965000D03* +D26* +%TO.C,C_SYS_2*% +X131250000Y-94250000D03* +X131250000Y-95210000D03* %TD*% D41* %TO.C,C_IMU_2*% -X140750000Y-68475000D03* -X140750000Y-70025000D03* +X125475000Y-125700000D03* +X123925000Y-125700000D03* +%TD*% +D20* +%TO.C,C_BAT1*% +X132250000Y-97750000D03* +X134150000Y-97750000D03* +%TD*% +D31* +%TO.C,R_STAT2*% +X132840000Y-100050000D03* +X133860000Y-100050000D03* %TD*% -D18* %TO.C,R_CC2*% X141265000Y-126065000D03* X142285000Y-126065000D03* %TD*% -D29* -%TO.C,C_OLED_2*% -X123960000Y-105200000D03* -X123000000Y-105200000D03* -%TD*% D42* %TO.C,D_OR2*% X133635000Y-72440000D03* X136935000Y-72440000D03* %TD*% -D18* +D31* %TO.C,R_LATCH_G1*% X131775000Y-74440000D03* X132795000Y-74440000D03* %TD*% D43* -%TO.C,U_MCU1*% -X127900000Y-101500000D03* -X127900000Y-100400000D03* -X127900000Y-99300000D03* -X127900000Y-98200000D03* -X127900000Y-97100000D03* -X127900000Y-96000000D03* -X127900000Y-94900000D03* -X127900000Y-93800000D03* -X141650000Y-93800000D03* -X141650000Y-94900000D03* -X141650000Y-96000000D03* -X141650000Y-97100000D03* -X141650000Y-98200000D03* -X141650000Y-99300000D03* -X141650000Y-100400000D03* -X141650000Y-101500000D03* -D44* -X132525000Y-100700000D03* -X132525000Y-99500000D03* -X132525000Y-98300000D03* -X132525000Y-97100000D03* -X132525000Y-95900000D03* -X132525000Y-94700000D03* -X132525000Y-93500000D03* -X134025000Y-100700000D03* -X134025000Y-99500000D03* -X134025000Y-98300000D03* -X134025000Y-97100000D03* -X134025000Y-95900000D03* -X134025000Y-94700000D03* -X134025000Y-93500000D03* -X135525000Y-100700000D03* -X135525000Y-99500000D03* -X135525000Y-98300000D03* -X135525000Y-97100000D03* -X135525000Y-95900000D03* -X135525000Y-94700000D03* -X135525000Y-93500000D03* -X137025000Y-100700000D03* -X137025000Y-99500000D03* -X137025000Y-98300000D03* -X137025000Y-97100000D03* -X137025000Y-95900000D03* -X137025000Y-94700000D03* -X137025000Y-93500000D03* -X138525000Y-100700000D03* -X138525000Y-99500000D03* -X138525000Y-98300000D03* -X138525000Y-97100000D03* -X138525000Y-95900000D03* -X138525000Y-94700000D03* -X138525000Y-93500000D03* -D45* -X131400000Y-102700000D03* -X133650000Y-102700000D03* -X135900000Y-102700000D03* -X138150000Y-102700000D03* -D44* -X140025000Y-95900000D03* -X140025000Y-94700000D03* -D46* -X140025000Y-93500000D03* -D44* -X131025000Y-100700000D03* -X131025000Y-99500000D03* -X131025000Y-98300000D03* -X131025000Y-97100000D03* -X131025000Y-95900000D03* -X131025000Y-94700000D03* -X131025000Y-93500000D03* +%TO.C,R_FB2*% +X138525000Y-100490000D03* +X138525000Y-101510000D03* %TD*% -D29* +D19* +%TO.C,R_VSET1*% +X122280000Y-99750000D03* +X121260000Y-99750000D03* +%TD*% +D35* %TO.C,C_IMU_3*% -X145230000Y-70000000D03* -X144270000Y-70000000D03* +X127660000Y-128500000D03* +X126700000Y-128500000D03* %TD*% -D18* +D19* +%TO.C,R_STAT1*% +X124670000Y-97250000D03* +X123650000Y-97250000D03* +%TD*% +%TO.C,R_ISET1*% +X122300000Y-98250000D03* +X121280000Y-98250000D03* +%TD*% +D31* %TO.C,R_CC1*% X130265000Y-123815000D03* X131285000Y-123815000D03* %TD*% -D47* -%TO.C,C_3V3_2*% -X144555000Y-95985000D03* -X144555000Y-95025000D03* -%TD*% -D48* -%TO.C,C_3V3_1*% -X142300000Y-91375000D03* -X143850000Y-91375000D03* -%TD*% -D18* -%TO.C,R_VSYS1*% -X133265000Y-91615000D03* -X134285000Y-91615000D03* -%TD*% -D49* -%TO.C,C_RF_BULK1*% -X146495000Y-96870000D03* -X146495000Y-93920000D03* -%TD*% -D38* -%TO.C,R_I2C_SDA1*% -X125875000Y-103010000D03* -X125875000Y-101990000D03* +D40* +%TO.C,R_FB1*% +X138525000Y-99510000D03* +X138525000Y-98490000D03* %TD*% -%TO.C,R_I2C_SCL1*% -X125875000Y-100760000D03* -X125875000Y-99740000D03* +D44* +%TO.C,U_XBEE1*% +X126450000Y-121300000D03* +X128990000Y-121300000D03* +X131530000Y-121300000D03* +X134070000Y-121300000D03* +X136610000Y-121300000D03* +X139150000Y-121300000D03* +X139150000Y-103600000D03* +X136610000Y-103600000D03* +X134070000Y-103600000D03* +X131530000Y-103600000D03* +X128990000Y-103600000D03* +X126450000Y-103600000D03* %TD*% -D28* -%TO.C,SW_RST1*% -X144100000Y-102850000D03* -X148250000Y-102850000D03* -X144100000Y-100700000D03* -X148250000Y-100700000D03* +D45* +%TO.C,U_BUCK1*% +X148425000Y-95750000D03* +X147475000Y-95750000D03* +X146525000Y-95750000D03* +X146525000Y-93475000D03* +X148425000Y-93475000D03* %TD*% -D50* +D36* %TO.C,C_IMU_1*% -X142250000Y-68520000D03* -X142250000Y-69480000D03* +X126720000Y-125900000D03* +X127680000Y-125900000D03* %TD*% -D18* -%TO.C,R_VSYS2*% -X135515000Y-91615000D03* -X136535000Y-91615000D03* +D46* +%TO.C,L_BUCK1*% +X144050000Y-95750000D03* +X141000000Y-95750000D03* %TD*% -D47* +D26* %TO.C,C_STICK1*% -X145505000Y-76685000D03* X145505000Y-75725000D03* +X145505000Y-76685000D03* %TD*% -D51* +D47* %TO.C,U_HALL1*% -X127625000Y-67950000D03* -X127625000Y-66050000D03* -X129500000Y-67000000D03* +X127437500Y-63800000D03* +X127437500Y-65700000D03* +X125562500Y-64750000D03* %TD*% +D48* %TO.C,Q_INV1*% X124061300Y-86915000D03* X124061300Y-85015000D03* X125936300Y-85965000D03* %TD*% -D52* +D43* %TO.C,R_TRIG1*% X129750000Y-90740000D03* X129750000Y-91760000D03* %TD*% -D38* -%TO.C,R_BOOT_PU1*% -X144565000Y-99285000D03* -X144565000Y-98265000D03* +D19* +%TO.C,R_TS1*% +X122280000Y-101250000D03* +X121260000Y-101250000D03* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-B_Paste.gbr b/PCB/v2.x/production/gerbers/snips_controller-B_Paste.gbr index d180a9c..b4f2f61 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-B_Paste.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-B_Paste.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Paste,Bot*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -29,142 +29,394 @@ G04 Aperture macros list* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% G04 Aperture macros list end* -%ADD10RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% -%ADD11RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% -%ADD12RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% -%ADD13RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% -%ADD14RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% -%ADD15RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% -%ADD16RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% -%ADD17R,1.050000X0.650000*% -%ADD18RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% -%ADD19RoundRect,0.218750X-0.218750X-0.256250X0.218750X-0.256250X0.218750X0.256250X-0.218750X0.256250X0*% -%ADD20RoundRect,0.087500X0.225000X0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0*% -%ADD21RoundRect,0.087500X0.087500X0.225000X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0*% -%ADD22RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% -%ADD23RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% -%ADD24RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% -%ADD25RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% -%ADD26RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% -%ADD27RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% -%ADD28RoundRect,0.225000X-0.250000X0.225000X-0.250000X-0.225000X0.250000X-0.225000X0.250000X0.225000X0*% -%ADD29RoundRect,0.225000X-0.225000X-0.375000X0.225000X-0.375000X0.225000X0.375000X-0.225000X0.375000X0*% -%ADD30R,1.250000X0.700000*% -%ADD31C,0.600000*% -%ADD32R,1.500000X1.500000*% -%ADD33R,0.600000X0.600000*% -%ADD34RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% -%ADD35RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% -%ADD36RoundRect,0.250000X0.650000X-0.325000X0.650000X0.325000X-0.650000X0.325000X-0.650000X-0.325000X0*% -%ADD37RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% -%ADD38RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% -%ADD39RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD10C,0.010000*% +%ADD11RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% +%ADD12RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% +%ADD13RoundRect,0.150000X-0.150000X0.587500X-0.150000X-0.587500X0.150000X-0.587500X0.150000X0.587500X0*% +%ADD14RoundRect,0.112500X-0.187500X-0.112500X0.187500X-0.112500X0.187500X0.112500X-0.187500X0.112500X0*% +%ADD15RoundRect,0.140000X-0.170000X0.140000X-0.170000X-0.140000X0.170000X-0.140000X0.170000X0.140000X0*% +%ADD16RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% +%ADD17RoundRect,0.250000X-0.475000X0.250000X-0.475000X-0.250000X0.475000X-0.250000X0.475000X0.250000X0*% +%ADD18RoundRect,0.112500X-0.112500X0.350000X-0.112500X-0.350000X0.112500X-0.350000X0.112500X0.350000X0*% +%ADD19RoundRect,0.225000X0.225000X0.375000X-0.225000X0.375000X-0.225000X-0.375000X0.225000X-0.375000X0*% +%ADD20RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD21RoundRect,0.087500X-0.087500X0.225000X-0.087500X-0.225000X0.087500X-0.225000X0.087500X0.225000X0*% +%ADD22RoundRect,0.087500X-0.225000X0.087500X-0.225000X-0.087500X0.225000X-0.087500X0.225000X0.087500X0*% +%ADD23RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% +%ADD24RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%ADD25RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% +%ADD26RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% +%ADD27RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% +%ADD28RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% +%ADD29RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% +%ADD30RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% +%ADD31RoundRect,0.052000X0.198000X0.048000X-0.198000X0.048000X-0.198000X-0.048000X0.198000X-0.048000X0*% +%ADD32RoundRect,0.225000X-0.225000X-0.375000X0.225000X-0.375000X0.225000X0.375000X-0.225000X0.375000X0*% +%ADD33RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD34RoundRect,0.150000X0.150000X-0.512500X0.150000X0.512500X-0.150000X0.512500X-0.150000X-0.512500X0*% +%ADD35R,1.500000X3.600000*% +%ADD36RoundRect,0.150000X0.587500X0.150000X-0.587500X0.150000X-0.587500X-0.150000X0.587500X-0.150000X0*% +%ADD37RoundRect,0.150000X-0.587500X-0.150000X0.587500X-0.150000X0.587500X0.150000X-0.587500X0.150000X0*% G04 APERTURE END LIST* D10* -%TO.C,R_BTN_PU1*% -X124900000Y-94600000D03* -X125920000Y-94600000D03* +%TO.C,U_CHG1*% +X129175000Y-96890000D02* +X129175000Y-95610000D01* +X129175000Y-95607000D01* +X129175000Y-95605000D01* +X129174000Y-95602000D01* +X129174000Y-95600000D01* +X129173000Y-95597000D01* +X129173000Y-95595000D01* +X129172000Y-95592000D01* +X129171000Y-95590000D01* +X129170000Y-95587000D01* +X129168000Y-95585000D01* +X129167000Y-95583000D01* +X129165000Y-95581000D01* +X129164000Y-95579000D01* +X129162000Y-95577000D01* +X129160000Y-95575000D01* +X129158000Y-95573000D01* +X129156000Y-95571000D01* +X129154000Y-95570000D01* +X129152000Y-95568000D01* +X129150000Y-95567000D01* +X129148000Y-95565000D01* +X129145000Y-95564000D01* +X129143000Y-95563000D01* +X129140000Y-95562000D01* +X129138000Y-95562000D01* +X129135000Y-95561000D01* +X129133000Y-95561000D01* +X129130000Y-95560000D01* +X129128000Y-95560000D01* +X129125000Y-95560000D01* +X128375000Y-95560000D01* +X128372000Y-95560000D01* +X128370000Y-95560000D01* +X128367000Y-95561000D01* +X128365000Y-95561000D01* +X128362000Y-95562000D01* +X128360000Y-95562000D01* +X128357000Y-95563000D01* +X128355000Y-95564000D01* +X128352000Y-95565000D01* +X128350000Y-95567000D01* +X128348000Y-95568000D01* +X128346000Y-95570000D01* +X128344000Y-95571000D01* +X128342000Y-95573000D01* +X128340000Y-95575000D01* +X128338000Y-95577000D01* +X128336000Y-95579000D01* +X128335000Y-95581000D01* +X128333000Y-95583000D01* +X128332000Y-95585000D01* +X128330000Y-95587000D01* +X128329000Y-95590000D01* +X128328000Y-95592000D01* +X128327000Y-95595000D01* +X128327000Y-95597000D01* +X128326000Y-95600000D01* +X128326000Y-95602000D01* +X128325000Y-95605000D01* +X128325000Y-95607000D01* +X128325000Y-95610000D01* +X128325000Y-96890000D01* +X128325000Y-96893000D01* +X128325000Y-96895000D01* +X128326000Y-96898000D01* +X128326000Y-96900000D01* +X128327000Y-96903000D01* +X128327000Y-96905000D01* +X128328000Y-96908000D01* +X128329000Y-96910000D01* +X128330000Y-96913000D01* +X128332000Y-96915000D01* +X128333000Y-96917000D01* +X128335000Y-96919000D01* +X128336000Y-96921000D01* +X128338000Y-96923000D01* +X128340000Y-96925000D01* +X128342000Y-96927000D01* +X128344000Y-96929000D01* +X128346000Y-96930000D01* +X128348000Y-96932000D01* +X128350000Y-96933000D01* +X128352000Y-96935000D01* +X128355000Y-96936000D01* +X128357000Y-96937000D01* +X128360000Y-96938000D01* +X128362000Y-96938000D01* +X128365000Y-96939000D01* +X128367000Y-96939000D01* +X128370000Y-96940000D01* +X128372000Y-96940000D01* +X128375000Y-96940000D01* +X129125000Y-96940000D01* +X129128000Y-96940000D01* +X129130000Y-96940000D01* +X129133000Y-96939000D01* +X129135000Y-96939000D01* +X129138000Y-96938000D01* +X129140000Y-96938000D01* +X129143000Y-96937000D01* +X129145000Y-96936000D01* +X129148000Y-96935000D01* +X129150000Y-96933000D01* +X129152000Y-96932000D01* +X129154000Y-96930000D01* +X129156000Y-96929000D01* +X129158000Y-96927000D01* +X129160000Y-96925000D01* +X129162000Y-96923000D01* +X129164000Y-96921000D01* +X129165000Y-96919000D01* +X129167000Y-96917000D01* +X129168000Y-96915000D01* +X129170000Y-96913000D01* +X129171000Y-96910000D01* +X129172000Y-96908000D01* +X129173000Y-96905000D01* +X129173000Y-96903000D01* +X129174000Y-96900000D01* +X129174000Y-96898000D01* +X129175000Y-96895000D01* +X129175000Y-96893000D01* +X129175000Y-96890000D01* +G36* +X129133000Y-95561000D02* +G01* +X129135000Y-95561000D01* +X129138000Y-95562000D01* +X129140000Y-95562000D01* +X129143000Y-95563000D01* +X129145000Y-95564000D01* +X129148000Y-95565000D01* +X129150000Y-95567000D01* +X129152000Y-95568000D01* +X129154000Y-95570000D01* +X129156000Y-95571000D01* +X129158000Y-95573000D01* +X129160000Y-95575000D01* +X129162000Y-95577000D01* +X129164000Y-95579000D01* +X129165000Y-95581000D01* +X129167000Y-95583000D01* +X129168000Y-95585000D01* +X129170000Y-95587000D01* +X129171000Y-95590000D01* +X129172000Y-95592000D01* +X129173000Y-95595000D01* +X129173000Y-95597000D01* +X129174000Y-95600000D01* +X129174000Y-95602000D01* +X129175000Y-95605000D01* +X129175000Y-95607000D01* +X129175000Y-95610000D01* +X129175000Y-96890000D01* +X129175000Y-96893000D01* +X129175000Y-96895000D01* +X129174000Y-96898000D01* +X129174000Y-96900000D01* +X129173000Y-96903000D01* +X129173000Y-96905000D01* +X129172000Y-96908000D01* +X129171000Y-96910000D01* +X129170000Y-96913000D01* +X129168000Y-96915000D01* +X129167000Y-96917000D01* +X129165000Y-96919000D01* +X129164000Y-96921000D01* +X129162000Y-96923000D01* +X129160000Y-96925000D01* +X129158000Y-96927000D01* +X129156000Y-96929000D01* +X129154000Y-96930000D01* +X129152000Y-96932000D01* +X129150000Y-96933000D01* +X129148000Y-96935000D01* +X129145000Y-96936000D01* +X129143000Y-96937000D01* +X129140000Y-96938000D01* +X129138000Y-96938000D01* +X129135000Y-96939000D01* +X129133000Y-96939000D01* +X129130000Y-96940000D01* +X129128000Y-96940000D01* +X129125000Y-96940000D01* +X128375000Y-96940000D01* +X128372000Y-96940000D01* +X128370000Y-96940000D01* +X128367000Y-96939000D01* +X128365000Y-96939000D01* +X128362000Y-96938000D01* +X128360000Y-96938000D01* +X128357000Y-96937000D01* +X128355000Y-96936000D01* +X128352000Y-96935000D01* +X128350000Y-96933000D01* +X128348000Y-96932000D01* +X128346000Y-96930000D01* +X128344000Y-96929000D01* +X128342000Y-96927000D01* +X128340000Y-96925000D01* +X128338000Y-96923000D01* +X128336000Y-96921000D01* +X128335000Y-96919000D01* +X128333000Y-96917000D01* +X128332000Y-96915000D01* +X128330000Y-96913000D01* +X128329000Y-96910000D01* +X128328000Y-96908000D01* +X128327000Y-96905000D01* +X128327000Y-96903000D01* +X128326000Y-96900000D01* +X128326000Y-96898000D01* +X128325000Y-96895000D01* +X128325000Y-96893000D01* +X128325000Y-96890000D01* +X128325000Y-95610000D01* +X128325000Y-95607000D01* +X128325000Y-95605000D01* +X128326000Y-95602000D01* +X128326000Y-95600000D01* +X128327000Y-95597000D01* +X128327000Y-95595000D01* +X128328000Y-95592000D01* +X128329000Y-95590000D01* +X128330000Y-95587000D01* +X128332000Y-95585000D01* +X128333000Y-95583000D01* +X128335000Y-95581000D01* +X128336000Y-95579000D01* +X128338000Y-95577000D01* +X128340000Y-95575000D01* +X128342000Y-95573000D01* +X128344000Y-95571000D01* +X128346000Y-95570000D01* +X128348000Y-95568000D01* +X128350000Y-95567000D01* +X128352000Y-95565000D01* +X128355000Y-95564000D01* +X128357000Y-95563000D01* +X128360000Y-95562000D01* +X128362000Y-95562000D01* +X128365000Y-95561000D01* +X128367000Y-95561000D01* +X128370000Y-95560000D01* +X128372000Y-95560000D01* +X128375000Y-95560000D01* +X129125000Y-95560000D01* +X129128000Y-95560000D01* +X129130000Y-95560000D01* +X129133000Y-95561000D01* +G37* %TD*% D11* +%TO.C,R_BTN_PU1*% +X127381250Y-93764999D03* +X126361250Y-93764999D03* +%TD*% +D12* +%TO.C,C_SYS_1*% +X133750000Y-94250000D03* +X135650000Y-94250000D03* +%TD*% +D13* %TO.C,Q_PWR1*% X137335000Y-77065000D03* X139235000Y-77065000D03* X138285000Y-78940000D03* %TD*% -D12* -%TO.C,C_VBUS1*% -X140500000Y-89525000D03* -X140500000Y-87975000D03* -%TD*% -D13* +D14* %TO.C,D_VBUS_TVS1*% X135845000Y-126245000D03* X137945000Y-126245000D03* %TD*% -D14* -%TO.C,C_OLED_1*% -X123575000Y-107800000D03* -X122025000Y-107800000D03* -%TD*% D15* +%TO.C,C_VIN_2*% +X125750000Y-95290000D03* +X125750000Y-96250000D03* +%TD*% +D16* +%TO.C,C_VIN_1*% +X123750000Y-95250000D03* +X121850000Y-95250000D03* +%TD*% +D17* +%TO.C,C_BUCK_OUT1*% +X138025000Y-94800000D03* +X138025000Y-96700000D03* +%TD*% +D18* %TO.C,D_INV_ISO1*% X124661300Y-90740000D03* X125961300Y-90740000D03* X125311300Y-92515000D03* %TD*% -D16* +D19* %TO.C,D_OR1*% X130135000Y-78690000D03* X126835000Y-78690000D03* %TD*% -D10* +D20* %TO.C,R_PWR_EN_PD1*% X140425000Y-80240000D03* X141445000Y-80240000D03* %TD*% -D17* -%TO.C,SW_BOOT1*% -X144100000Y-106950000D03* -X148250000Y-106950000D03* -X144100000Y-104800000D03* -X148250000Y-104800000D03* -%TD*% -D18* -%TO.C,C_TRIG1*% -X131980000Y-91750000D03* -X131020000Y-91750000D03* -%TD*% -D19* -%TO.C,FB_RF1*% -X139037500Y-91375000D03* -X140612500Y-91375000D03* -%TD*% -D20* -%TO.C,U_IMU1*% -X145862500Y-67050000D03* -X145862500Y-67550000D03* -X145862500Y-68050000D03* -X145862500Y-68550000D03* D21* -X145200000Y-68712500D03* -X144700000Y-68712500D03* -X144200000Y-68712500D03* -D20* -X143537500Y-68550000D03* -X143537500Y-68050000D03* -X143537500Y-67550000D03* -X143537500Y-67050000D03* +%TO.C,U_IMU1*% +X129062500Y-126100000D03* +X129562500Y-126100000D03* +X130062500Y-126100000D03* +X130562500Y-126100000D03* +D22* +X130725000Y-126762500D03* +X130725000Y-127262500D03* +X130725000Y-127762500D03* D21* -X144200000Y-66887500D03* -X144700000Y-66887500D03* -X145200000Y-66887500D03* +X130562500Y-128425000D03* +X130062500Y-128425000D03* +X129562500Y-128425000D03* +X129062500Y-128425000D03* +D22* +X128900000Y-127762500D03* +X128900000Y-127262500D03* +X128900000Y-126762500D03* %TD*% -D18* +D23* +%TO.C,C_BUCK_IN1*% +X146500000Y-91550000D03* +X146500000Y-89650000D03* +%TD*% +D24* %TO.C,C_LATCH_G1*% X135485000Y-74890000D03* X134525000Y-74890000D03* %TD*% -D22* +D25* %TO.C,C_HALL1*% -X128320000Y-64600000D03* -X129280000Y-64600000D03* +X128940000Y-63800000D03* +X129900000Y-63800000D03* %TD*% -D23* +D11* %TO.C,R_INV_BASE1*% X125881300Y-88965000D03* X124861300Y-88965000D03* %TD*% -D24* +D26* %TO.C,SW_TRIG_DIG1*% X133775000Y-62700000D03* X136225000Y-62700000D03* -D25* +D27* X135000000Y-62700000D03* -D26* +D28* X133150000Y-60750000D03* X136850000Y-60750000D03* %TD*% -D27* +D29* %TO.C,R_INV_PU1*% X128461300Y-91725000D03* X128461300Y-90705000D03* @@ -173,190 +425,136 @@ X128461300Y-90705000D03* X140785000Y-76960000D03* X140785000Y-75940000D03* %TD*% -D11* +D13* %TO.C,Q_LATCH1*% X133385000Y-76940000D03* X135285000Y-76940000D03* X134335000Y-78815000D03* %TD*% -D28* +D15* +%TO.C,C_SYS_2*% +X131250000Y-94250000D03* +X131250000Y-95210000D03* +%TD*% +D30* %TO.C,C_IMU_2*% -X140750000Y-68475000D03* -X140750000Y-70025000D03* +X125475000Y-125700000D03* +X123925000Y-125700000D03* +%TD*% +D12* +%TO.C,C_BAT1*% +X132250000Y-97750000D03* +X134150000Y-97750000D03* +%TD*% +D31* +%TO.C,U_CHG1*% +X129800000Y-95450000D03* +X129800000Y-95850000D03* +X129800000Y-96250000D03* +X129800000Y-96650000D03* +X129800000Y-97050000D03* +X127700000Y-97050000D03* +X127700000Y-96650000D03* +X127700000Y-96250000D03* +X127700000Y-95850000D03* +X127700000Y-95450000D03* +%TD*% +D20* +%TO.C,R_STAT2*% +X132840000Y-100050000D03* +X133860000Y-100050000D03* %TD*% -D10* %TO.C,R_CC2*% X141265000Y-126065000D03* X142285000Y-126065000D03* %TD*% -D18* -%TO.C,C_OLED_2*% -X123960000Y-105200000D03* -X123000000Y-105200000D03* -%TD*% -D29* +D32* %TO.C,D_OR2*% X133635000Y-72440000D03* X136935000Y-72440000D03* %TD*% -D10* +D20* %TO.C,R_LATCH_G1*% X131775000Y-74440000D03* X132795000Y-74440000D03* %TD*% -D30* -%TO.C,U_MCU1*% -X127900000Y-101500000D03* -X127900000Y-100400000D03* -X127900000Y-99300000D03* -X127900000Y-98200000D03* -X127900000Y-97100000D03* -X127900000Y-96000000D03* -X127900000Y-94900000D03* -X127900000Y-93800000D03* -X141650000Y-93800000D03* -X141650000Y-94900000D03* -X141650000Y-96000000D03* -X141650000Y-97100000D03* -X141650000Y-98200000D03* -X141650000Y-99300000D03* -X141650000Y-100400000D03* -X141650000Y-101500000D03* -D31* -X132525000Y-100700000D03* -X132525000Y-99500000D03* -X132525000Y-98300000D03* -X132525000Y-97100000D03* -X132525000Y-95900000D03* -X132525000Y-94700000D03* -X132525000Y-93500000D03* -X134025000Y-100700000D03* -X134025000Y-99500000D03* -X134025000Y-98300000D03* -X134025000Y-97100000D03* -X134025000Y-95900000D03* -X134025000Y-94700000D03* -X134025000Y-93500000D03* -X135525000Y-100700000D03* -X135525000Y-99500000D03* -X135525000Y-98300000D03* -X135525000Y-97100000D03* -X135525000Y-95900000D03* -X135525000Y-94700000D03* -X135525000Y-93500000D03* -X137025000Y-100700000D03* -X137025000Y-99500000D03* -X137025000Y-98300000D03* -X137025000Y-97100000D03* -X137025000Y-95900000D03* -X137025000Y-94700000D03* -X137025000Y-93500000D03* -X138525000Y-100700000D03* -X138525000Y-99500000D03* -X138525000Y-98300000D03* -X138525000Y-97100000D03* -X138525000Y-95900000D03* -X138525000Y-94700000D03* -X138525000Y-93500000D03* -D32* -X131400000Y-102700000D03* -X133650000Y-102700000D03* -X135900000Y-102700000D03* -X138150000Y-102700000D03* -D31* -X140025000Y-95900000D03* -X140025000Y-94700000D03* D33* -X140025000Y-93500000D03* -D31* -X131025000Y-100700000D03* -X131025000Y-99500000D03* -X131025000Y-98300000D03* -X131025000Y-97100000D03* -X131025000Y-95900000D03* -X131025000Y-94700000D03* -X131025000Y-93500000D03* +%TO.C,R_FB2*% +X138525000Y-100490000D03* +X138525000Y-101510000D03* %TD*% -D18* +D11* +%TO.C,R_VSET1*% +X122280000Y-99750000D03* +X121260000Y-99750000D03* +%TD*% +D24* %TO.C,C_IMU_3*% -X145230000Y-70000000D03* -X144270000Y-70000000D03* +X127660000Y-128500000D03* +X126700000Y-128500000D03* %TD*% -D10* +D11* +%TO.C,R_STAT1*% +X124670000Y-97250000D03* +X123650000Y-97250000D03* +%TD*% +%TO.C,R_ISET1*% +X122300000Y-98250000D03* +X121280000Y-98250000D03* +%TD*% +D20* %TO.C,R_CC1*% X130265000Y-123815000D03* X131285000Y-123815000D03* %TD*% -D34* -%TO.C,C_3V3_2*% -X144555000Y-95985000D03* -X144555000Y-95025000D03* -%TD*% -D35* -%TO.C,C_3V3_1*% -X142300000Y-91375000D03* -X143850000Y-91375000D03* -%TD*% -D10* -%TO.C,R_VSYS1*% -X133265000Y-91615000D03* -X134285000Y-91615000D03* -%TD*% -D36* -%TO.C,C_RF_BULK1*% -X146495000Y-96870000D03* -X146495000Y-93920000D03* -%TD*% -D27* -%TO.C,R_I2C_SDA1*% -X125875000Y-103010000D03* -X125875000Y-101990000D03* -%TD*% -%TO.C,R_I2C_SCL1*% -X125875000Y-100760000D03* -X125875000Y-99740000D03* +D29* +%TO.C,R_FB1*% +X138525000Y-99510000D03* +X138525000Y-98490000D03* %TD*% -D17* -%TO.C,SW_RST1*% -X144100000Y-102850000D03* -X148250000Y-102850000D03* -X144100000Y-100700000D03* -X148250000Y-100700000D03* +D34* +%TO.C,U_BUCK1*% +X148425000Y-95750000D03* +X147475000Y-95750000D03* +X146525000Y-95750000D03* +X146525000Y-93475000D03* +X148425000Y-93475000D03* %TD*% -D37* +D25* %TO.C,C_IMU_1*% -X142250000Y-68520000D03* -X142250000Y-69480000D03* +X126720000Y-125900000D03* +X127680000Y-125900000D03* %TD*% -D10* -%TO.C,R_VSYS2*% -X135515000Y-91615000D03* -X136535000Y-91615000D03* +D35* +%TO.C,L_BUCK1*% +X144050000Y-95750000D03* +X141000000Y-95750000D03* %TD*% -D34* +D15* %TO.C,C_STICK1*% -X145505000Y-76685000D03* X145505000Y-75725000D03* +X145505000Y-76685000D03* %TD*% -D38* +D36* %TO.C,U_HALL1*% -X127625000Y-67950000D03* -X127625000Y-66050000D03* -X129500000Y-67000000D03* +X127437500Y-63800000D03* +X127437500Y-65700000D03* +X125562500Y-64750000D03* %TD*% +D37* %TO.C,Q_INV1*% X124061300Y-86915000D03* X124061300Y-85015000D03* X125936300Y-85965000D03* %TD*% -D39* +D33* %TO.C,R_TRIG1*% X129750000Y-90740000D03* X129750000Y-91760000D03* %TD*% -D27* -%TO.C,R_BOOT_PU1*% -X144565000Y-99285000D03* -X144565000Y-98265000D03* +D11* +%TO.C,R_TS1*% +X122280000Y-101250000D03* +X121260000Y-101250000D03* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-B_Silkscreen.gbr b/PCB/v2.x/production/gerbers/snips_controller-B_Silkscreen.gbr index d0aeaa6..529615b 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-B_Silkscreen.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-B_Silkscreen.gbr @@ -1,207 +1,22 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Legend,Bot*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* G04 APERTURE LIST* -%ADD10C,0.120000*% -%ADD11C,0.150000*% +%ADD10C,0.150000*% +%ADD11C,0.120000*% %ADD12C,0.000000*% %ADD13C,0.200000*% G04 APERTURE END LIST* D10* -X147265714Y-108154806D02* -X147151428Y-108192901D01* -X147151428Y-108192901D02* -X147113333Y-108230997D01* -X147113333Y-108230997D02* -X147075237Y-108307187D01* -X147075237Y-108307187D02* -X147075237Y-108421473D01* -X147075237Y-108421473D02* -X147113333Y-108497663D01* -X147113333Y-108497663D02* -X147151428Y-108535759D01* -X147151428Y-108535759D02* -X147227618Y-108573854D01* -X147227618Y-108573854D02* -X147532380Y-108573854D01* -X147532380Y-108573854D02* -X147532380Y-107773854D01* -X147532380Y-107773854D02* -X147265714Y-107773854D01* -X147265714Y-107773854D02* -X147189523Y-107811949D01* -X147189523Y-107811949D02* -X147151428Y-107850044D01* -X147151428Y-107850044D02* -X147113333Y-107926235D01* -X147113333Y-107926235D02* -X147113333Y-108002425D01* -X147113333Y-108002425D02* -X147151428Y-108078616D01* -X147151428Y-108078616D02* -X147189523Y-108116711D01* -X147189523Y-108116711D02* -X147265714Y-108154806D01* -X147265714Y-108154806D02* -X147532380Y-108154806D01* -X146579999Y-107773854D02* -X146427618Y-107773854D01* -X146427618Y-107773854D02* -X146351428Y-107811949D01* -X146351428Y-107811949D02* -X146275237Y-107888139D01* -X146275237Y-107888139D02* -X146237142Y-108040520D01* -X146237142Y-108040520D02* -X146237142Y-108307187D01* -X146237142Y-108307187D02* -X146275237Y-108459568D01* -X146275237Y-108459568D02* -X146351428Y-108535759D01* -X146351428Y-108535759D02* -X146427618Y-108573854D01* -X146427618Y-108573854D02* -X146579999Y-108573854D01* -X146579999Y-108573854D02* -X146656190Y-108535759D01* -X146656190Y-108535759D02* -X146732380Y-108459568D01* -X146732380Y-108459568D02* -X146770476Y-108307187D01* -X146770476Y-108307187D02* -X146770476Y-108040520D01* -X146770476Y-108040520D02* -X146732380Y-107888139D01* -X146732380Y-107888139D02* -X146656190Y-107811949D01* -X146656190Y-107811949D02* -X146579999Y-107773854D01* -X145741904Y-107773854D02* -X145589523Y-107773854D01* -X145589523Y-107773854D02* -X145513333Y-107811949D01* -X145513333Y-107811949D02* -X145437142Y-107888139D01* -X145437142Y-107888139D02* -X145399047Y-108040520D01* -X145399047Y-108040520D02* -X145399047Y-108307187D01* -X145399047Y-108307187D02* -X145437142Y-108459568D01* -X145437142Y-108459568D02* -X145513333Y-108535759D01* -X145513333Y-108535759D02* -X145589523Y-108573854D01* -X145589523Y-108573854D02* -X145741904Y-108573854D01* -X145741904Y-108573854D02* -X145818095Y-108535759D01* -X145818095Y-108535759D02* -X145894285Y-108459568D01* -X145894285Y-108459568D02* -X145932381Y-108307187D01* -X145932381Y-108307187D02* -X145932381Y-108040520D01* -X145932381Y-108040520D02* -X145894285Y-107888139D01* -X145894285Y-107888139D02* -X145818095Y-107811949D01* -X145818095Y-107811949D02* -X145741904Y-107773854D01* -X145170476Y-107773854D02* -X144713333Y-107773854D01* -X144941905Y-108573854D02* -X144941905Y-107773854D01* -X148161904Y-99663855D02* -X148428571Y-99282902D01* -X148619047Y-99663855D02* -X148619047Y-98863855D01* -X148619047Y-98863855D02* -X148314285Y-98863855D01* -X148314285Y-98863855D02* -X148238095Y-98901950D01* -X148238095Y-98901950D02* -X148200000Y-98940045D01* -X148200000Y-98940045D02* -X148161904Y-99016236D01* -X148161904Y-99016236D02* -X148161904Y-99130521D01* -X148161904Y-99130521D02* -X148200000Y-99206712D01* -X148200000Y-99206712D02* -X148238095Y-99244807D01* -X148238095Y-99244807D02* -X148314285Y-99282902D01* -X148314285Y-99282902D02* -X148619047Y-99282902D01* -X147819047Y-99244807D02* -X147552381Y-99244807D01* -X147438095Y-99663855D02* -X147819047Y-99663855D01* -X147819047Y-99663855D02* -X147819047Y-98863855D01* -X147819047Y-98863855D02* -X147438095Y-98863855D01* -X147133333Y-99625760D02* -X147019047Y-99663855D01* -X147019047Y-99663855D02* -X146828571Y-99663855D01* -X146828571Y-99663855D02* -X146752380Y-99625760D01* -X146752380Y-99625760D02* -X146714285Y-99587664D01* -X146714285Y-99587664D02* -X146676190Y-99511474D01* -X146676190Y-99511474D02* -X146676190Y-99435283D01* -X146676190Y-99435283D02* -X146714285Y-99359093D01* -X146714285Y-99359093D02* -X146752380Y-99320998D01* -X146752380Y-99320998D02* -X146828571Y-99282902D01* -X146828571Y-99282902D02* -X146980952Y-99244807D01* -X146980952Y-99244807D02* -X147057142Y-99206712D01* -X147057142Y-99206712D02* -X147095237Y-99168617D01* -X147095237Y-99168617D02* -X147133333Y-99092426D01* -X147133333Y-99092426D02* -X147133333Y-99016236D01* -X147133333Y-99016236D02* -X147095237Y-98940045D01* -X147095237Y-98940045D02* -X147057142Y-98901950D01* -X147057142Y-98901950D02* -X146980952Y-98863855D01* -X146980952Y-98863855D02* -X146790475Y-98863855D01* -X146790475Y-98863855D02* -X146676190Y-98901950D01* -X146333332Y-99244807D02* -X146066666Y-99244807D01* -X145952380Y-99663855D02* -X146333332Y-99663855D01* -X146333332Y-99663855D02* -X146333332Y-98863855D01* -X146333332Y-98863855D02* -X145952380Y-98863855D01* -X145723808Y-98863855D02* -X145266665Y-98863855D01* -X145495237Y-99663855D02* -X145495237Y-98863855D01* -D11* X145004761Y-115857533D02* X144395238Y-115857533D01* X144699999Y-116162295D02* @@ -209,11 +24,16 @@ X144699999Y-115552771D01* X148204761Y-115857533D02* X147595238Y-115857533D01* %TO.C,R_BTN_PU1*% -D10* -X125256359Y-94220000D02* -X125563641Y-94220000D01* -X125256359Y-94980000D02* -X125563641Y-94980000D01* +D11* +X127024891Y-93384999D02* +X126717609Y-93384999D01* +X127024891Y-94144999D02* +X126717609Y-94144999D01* +%TO.C,C_SYS_1*% +X134438748Y-93515000D02* +X134961252Y-93515000D01* +X134438748Y-94985000D02* +X134961252Y-94985000D01* %TO.C,Q_PWR1*% X136725000Y-77242500D02* X136725000Y-78762500D01* @@ -240,11 +60,6 @@ X137905000Y-76702500D01* X138235000Y-76462500D01* X138235000Y-76942500D01* G37* -%TO.C,C_VBUS1*% -X139990000Y-88890580D02* -X139990000Y-88609420D01* -X141010000Y-88890580D02* -X141010000Y-88609420D01* %TO.C,D_VBUS_TVS1*% X135285000Y-125395000D02* X137945000Y-125395000D01* @@ -297,11 +112,21 @@ X148500000Y-119000000D01* X148500000Y-120600000D01* X147500000Y-120600000D01* X147500000Y-119000000D01* -%TO.C,C_OLED_1*% -X122940580Y-107290000D02* -X122659420Y-107290000D01* -X122940580Y-108310000D02* -X122659420Y-108310000D01* +%TO.C,C_VIN_2*% +X125390000Y-95662164D02* +X125390000Y-95877836D01* +X126110000Y-95662164D02* +X126110000Y-95877836D01* +%TO.C,C_VIN_1*% +X123061252Y-94515000D02* +X122538748Y-94515000D01* +X123061252Y-95985000D02* +X122538748Y-95985000D01* +%TO.C,C_BUCK_OUT1*% +X137290000Y-95488748D02* +X137290000Y-96011252D01* +X138760000Y-95488748D02* +X138760000Y-96011252D01* %TO.C,D_INV_ISO1*% X124176300Y-90892500D02* X124176300Y-92362500D01* @@ -336,1778 +161,1756 @@ X140781359Y-79860000D02* X141088641Y-79860000D01* X140781359Y-80620000D02* X141088641Y-80620000D01* -%TO.C,SW_BOOT1*% -X143975000Y-104175000D02* -X148375000Y-104175000D01* -X143975000Y-104295000D02* -X143975000Y-104175000D01* -X143975000Y-106445000D02* -X143975000Y-105305000D01* -X143975000Y-107575000D02* -X143975000Y-107455000D01* -X148375000Y-104175000D02* -X148375000Y-104295000D01* -X148375000Y-105305000D02* -X148375000Y-106445000D01* -X148375000Y-107455000D02* -X148375000Y-107575000D01* -X148375000Y-107575000D02* -X143975000Y-107575000D01* -%TO.C,C_TRIG1*% -X131607836Y-91390000D02* -X131392164Y-91390000D01* -X131607836Y-92110000D02* -X131392164Y-92110000D01* -%TO.C,FB_RF1*% -X139662221Y-90865000D02* -X139987779Y-90865000D01* -X139662221Y-91885000D02* -X139987779Y-91885000D01* D12* %TO.C,LOGO1*% G36* -X121775000Y-64635000D02* +X129175000Y-108035000D02* G01* -X120445000Y-64635000D01* -X120445000Y-64445000D01* -X121775000Y-64445000D01* -X121775000Y-64635000D01* +X127845000Y-108035000D01* +X127845000Y-107845000D01* +X129175000Y-107845000D01* +X129175000Y-108035000D01* G37* G36* -X120635000Y-64825000D02* +X128035000Y-108225000D02* G01* -X120445000Y-64825000D01* -X120445000Y-64635000D01* -X120635000Y-64635000D01* -X120635000Y-64825000D01* +X127845000Y-108225000D01* +X127845000Y-108035000D01* +X128035000Y-108035000D01* +X128035000Y-108225000D01* G37* G36* -X120635000Y-65015000D02* +X128035000Y-108415000D02* G01* -X120445000Y-65015000D01* -X120445000Y-64825000D01* -X120635000Y-64825000D01* -X120635000Y-65015000D01* +X127845000Y-108415000D01* +X127845000Y-108225000D01* +X128035000Y-108225000D01* +X128035000Y-108415000D01* G37* G36* -X120635000Y-65205000D02* +X128035000Y-108605000D02* G01* -X120445000Y-65205000D01* -X120445000Y-65015000D01* -X120635000Y-65015000D01* -X120635000Y-65205000D01* +X127845000Y-108605000D01* +X127845000Y-108415000D01* +X128035000Y-108415000D01* +X128035000Y-108605000D01* G37* G36* -X120635000Y-65395000D02* +X128035000Y-108795000D02* G01* -X120445000Y-65395000D01* -X120445000Y-65205000D01* -X120635000Y-65205000D01* -X120635000Y-65395000D01* +X127845000Y-108795000D01* +X127845000Y-108605000D01* +X128035000Y-108605000D01* +X128035000Y-108795000D01* G37* G36* -X120635000Y-65585000D02* +X128035000Y-108985000D02* G01* -X120445000Y-65585000D01* -X120445000Y-65395000D01* -X120635000Y-65395000D01* -X120635000Y-65585000D01* +X127845000Y-108985000D01* +X127845000Y-108795000D01* +X128035000Y-108795000D01* +X128035000Y-108985000D01* G37* G36* -X121775000Y-65775000D02* +X129175000Y-109175000D02* G01* -X120445000Y-65775000D01* -X120445000Y-65585000D01* -X121775000Y-65585000D01* -X121775000Y-65775000D01* +X127845000Y-109175000D01* +X127845000Y-108985000D01* +X129175000Y-108985000D01* +X129175000Y-109175000D01* G37* G36* -X120635000Y-66915000D02* +X128035000Y-110315000D02* G01* -X120445000Y-66915000D01* -X120445000Y-66725000D01* -X120635000Y-66725000D01* -X120635000Y-66915000D01* +X127845000Y-110315000D01* +X127845000Y-110125000D01* +X128035000Y-110125000D01* +X128035000Y-110315000D01* G37* G36* -X120825000Y-67105000D02* +X128225000Y-110505000D02* G01* -X120445000Y-67105000D01* -X120445000Y-66915000D01* -X120825000Y-66915000D01* -X120825000Y-67105000D01* +X127845000Y-110505000D01* +X127845000Y-110315000D01* +X128225000Y-110315000D01* +X128225000Y-110505000D01* G37* G36* -X120635000Y-67485000D02* +X128035000Y-110885000D02* G01* -X120445000Y-67485000D01* -X120445000Y-67295000D01* -X120635000Y-67295000D01* -X120635000Y-67485000D01* +X127845000Y-110885000D01* +X127845000Y-110695000D01* +X128035000Y-110695000D01* +X128035000Y-110885000D01* G37* G36* -X121015000Y-67865000D02* +X128415000Y-111265000D02* G01* -X120445000Y-67865000D01* -X120445000Y-67675000D01* -X121015000Y-67675000D01* -X121015000Y-67865000D01* +X127845000Y-111265000D01* +X127845000Y-111075000D01* +X128415000Y-111075000D01* +X128415000Y-111265000D01* G37* G36* -X120635000Y-68055000D02* +X128035000Y-111455000D02* G01* -X120445000Y-68055000D01* -X120445000Y-67865000D01* -X120635000Y-67865000D01* -X120635000Y-68055000D01* +X127845000Y-111455000D01* +X127845000Y-111265000D01* +X128035000Y-111265000D01* +X128035000Y-111455000D01* G37* G36* -X121015000Y-68435000D02* +X128415000Y-111835000D02* G01* -X120445000Y-68435000D01* -X120445000Y-68245000D01* -X121015000Y-68245000D01* -X121015000Y-68435000D01* +X127845000Y-111835000D01* +X127845000Y-111645000D01* +X128415000Y-111645000D01* +X128415000Y-111835000D01* G37* G36* -X120635000Y-69005000D02* +X128035000Y-112405000D02* G01* -X120445000Y-69005000D01* -X120445000Y-68815000D01* -X120635000Y-68815000D01* -X120635000Y-69005000D01* +X127845000Y-112405000D01* +X127845000Y-112215000D01* +X128035000Y-112215000D01* +X128035000Y-112405000D01* G37* G36* -X120825000Y-69195000D02* +X128225000Y-112595000D02* G01* -X120445000Y-69195000D01* -X120445000Y-69005000D01* -X120825000Y-69005000D01* -X120825000Y-69195000D01* +X127845000Y-112595000D01* +X127845000Y-112405000D01* +X128225000Y-112405000D01* +X128225000Y-112595000D01* G37* G36* -X121205000Y-69385000D02* +X128605000Y-112785000D02* G01* -X120445000Y-69385000D01* -X120445000Y-69195000D01* -X121205000Y-69195000D01* -X121205000Y-69385000D01* +X127845000Y-112785000D01* +X127845000Y-112595000D01* +X128605000Y-112595000D01* +X128605000Y-112785000D01* G37* G36* -X120635000Y-69765000D02* +X128035000Y-113165000D02* G01* -X120445000Y-69765000D01* -X120445000Y-69575000D01* -X120635000Y-69575000D01* -X120635000Y-69765000D01* +X127845000Y-113165000D01* +X127845000Y-112975000D01* +X128035000Y-112975000D01* +X128035000Y-113165000D01* G37* G36* -X121015000Y-66345000D02* +X128415000Y-109745000D02* G01* -X120635000Y-66345000D01* -X120635000Y-66155000D01* -X121015000Y-66155000D01* -X121015000Y-66345000D01* +X128035000Y-109745000D01* +X128035000Y-109555000D01* +X128415000Y-109555000D01* +X128415000Y-109745000D01* G37* G36* -X122345000Y-69575000D02* +X129745000Y-112975000D02* G01* -X120635000Y-69575000D01* -X120635000Y-69385000D01* -X122345000Y-69385000D01* -X122345000Y-69575000D01* +X128035000Y-112975000D01* +X128035000Y-112785000D01* +X129745000Y-112785000D01* +X129745000Y-112975000D01* G37* G36* -X121395000Y-65015000D02* +X128795000Y-108415000D02* G01* -X120825000Y-65015000D01* -X120825000Y-64825000D01* -X121395000Y-64825000D01* -X121395000Y-65015000D01* +X128225000Y-108415000D01* +X128225000Y-108225000D01* +X128795000Y-108225000D01* +X128795000Y-108415000D01* G37* G36* -X121395000Y-65205000D02* +X128795000Y-108605000D02* G01* -X120825000Y-65205000D01* -X120825000Y-65015000D01* -X121395000Y-65015000D01* -X121395000Y-65205000D01* +X128225000Y-108605000D01* +X128225000Y-108415000D01* +X128795000Y-108415000D01* +X128795000Y-108605000D01* G37* G36* -X121395000Y-65395000D02* +X128795000Y-108795000D02* G01* -X120825000Y-65395000D01* -X120825000Y-65205000D01* -X121395000Y-65205000D01* -X121395000Y-65395000D01* +X128225000Y-108795000D01* +X128225000Y-108605000D01* +X128795000Y-108605000D01* +X128795000Y-108795000D01* G37* G36* -X121395000Y-67295000D02* +X128795000Y-110695000D02* G01* -X120825000Y-67295000D01* -X120825000Y-67105000D01* -X121395000Y-67105000D01* -X121395000Y-67295000D01* +X128225000Y-110695000D01* +X128225000Y-110505000D01* +X128795000Y-110505000D01* +X128795000Y-110695000D01* G37* G36* -X121015000Y-67485000D02* +X128415000Y-110885000D02* G01* -X120825000Y-67485000D01* -X120825000Y-67295000D01* -X121015000Y-67295000D01* -X121015000Y-67485000D01* +X128225000Y-110885000D01* +X128225000Y-110695000D01* +X128415000Y-110695000D01* +X128415000Y-110885000D01* G37* G36* -X121205000Y-67675000D02* +X128605000Y-111075000D02* G01* -X120825000Y-67675000D01* -X120825000Y-67485000D01* -X121205000Y-67485000D01* -X121205000Y-67675000D01* +X128225000Y-111075000D01* +X128225000Y-110885000D01* +X128605000Y-110885000D01* +X128605000Y-111075000D01* G37* G36* -X121395000Y-68815000D02* +X128795000Y-112215000D02* G01* -X120825000Y-68815000D01* -X120825000Y-68625000D01* -X121395000Y-68625000D01* -X121395000Y-68815000D01* +X128225000Y-112215000D01* +X128225000Y-112025000D01* +X128795000Y-112025000D01* +X128795000Y-112215000D01* G37* G36* -X121205000Y-69765000D02* +X128605000Y-113165000D02* G01* -X120825000Y-69765000D01* -X120825000Y-69575000D01* -X121205000Y-69575000D01* -X121205000Y-69765000D01* +X128225000Y-113165000D01* +X128225000Y-112975000D01* +X128605000Y-112975000D01* +X128605000Y-113165000D01* G37* G36* -X121015000Y-69955000D02* +X128415000Y-113355000D02* G01* -X120825000Y-69955000D01* -X120825000Y-69765000D01* -X121015000Y-69765000D01* -X121015000Y-69955000D01* +X128225000Y-113355000D01* +X128225000Y-113165000D01* +X128415000Y-113165000D01* +X128415000Y-113355000D01* G37* G36* -X121395000Y-66155000D02* +X128795000Y-109555000D02* G01* -X121015000Y-66155000D01* -X121015000Y-65965000D01* -X121395000Y-65965000D01* -X121395000Y-66155000D01* +X128415000Y-109555000D01* +X128415000Y-109365000D01* +X128795000Y-109365000D01* +X128795000Y-109555000D01* G37* G36* -X121205000Y-66725000D02* +X128605000Y-110125000D02* G01* -X121015000Y-66725000D01* -X121015000Y-66535000D01* -X121205000Y-66535000D01* -X121205000Y-66725000D01* +X128415000Y-110125000D01* +X128415000Y-109935000D01* +X128605000Y-109935000D01* +X128605000Y-110125000D01* G37* G36* -X121395000Y-68055000D02* +X128795000Y-111455000D02* G01* -X121015000Y-68055000D01* -X121015000Y-67865000D01* -X121395000Y-67865000D01* -X121395000Y-68055000D01* +X128415000Y-111455000D01* +X128415000Y-111265000D01* +X128795000Y-111265000D01* +X128795000Y-111455000D01* G37* G36* -X121395000Y-68625000D02* +X128795000Y-112025000D02* G01* -X121015000Y-68625000D01* -X121015000Y-68435000D01* -X121395000Y-68435000D01* -X121395000Y-68625000D01* +X128415000Y-112025000D01* +X128415000Y-111835000D01* +X128795000Y-111835000D01* +X128795000Y-112025000D01* G37* G36* -X122345000Y-69195000D02* +X129745000Y-112595000D02* G01* -X121015000Y-69195000D01* -X121015000Y-69005000D01* -X122345000Y-69005000D01* -X122345000Y-69195000D01* +X128415000Y-112595000D01* +X128415000Y-112405000D01* +X129745000Y-112405000D01* +X129745000Y-112595000D01* G37* G36* -X121585000Y-66345000D02* +X128985000Y-109745000D02* G01* -X121205000Y-66345000D01* -X121205000Y-66155000D01* -X121585000Y-66155000D01* -X121585000Y-66345000D01* +X128605000Y-109745000D01* +X128605000Y-109555000D01* +X128985000Y-109555000D01* +X128985000Y-109745000D01* G37* G36* -X121395000Y-66535000D02* +X128795000Y-109935000D02* G01* -X121205000Y-66535000D01* -X121205000Y-66345000D01* -X121395000Y-66345000D01* -X121395000Y-66535000D01* +X128605000Y-109935000D01* +X128605000Y-109745000D01* +X128795000Y-109745000D01* +X128795000Y-109935000D01* G37* G36* -X121775000Y-67105000D02* +X129175000Y-110505000D02* G01* -X121205000Y-67105000D01* -X121205000Y-66915000D01* -X121775000Y-66915000D01* -X121775000Y-67105000D01* +X128605000Y-110505000D01* +X128605000Y-110315000D01* +X129175000Y-110315000D01* +X129175000Y-110505000D01* G37* G36* -X121585000Y-67485000D02* +X128985000Y-110885000D02* G01* -X121205000Y-67485000D01* -X121205000Y-67295000D01* -X121585000Y-67295000D01* -X121585000Y-67485000D01* +X128605000Y-110885000D01* +X128605000Y-110695000D01* +X128985000Y-110695000D01* +X128985000Y-110885000D01* G37* G36* -X121775000Y-67865000D02* +X129175000Y-111265000D02* G01* -X121205000Y-67865000D01* -X121205000Y-67675000D01* -X121775000Y-67675000D01* -X121775000Y-67865000D01* +X128605000Y-111265000D01* +X128605000Y-111075000D01* +X129175000Y-111075000D01* +X129175000Y-111265000D01* G37* G36* -X122345000Y-68435000D02* +X129745000Y-111835000D02* G01* -X121205000Y-68435000D01* -X121205000Y-68245000D01* -X122345000Y-68245000D01* -X122345000Y-68435000D01* +X128605000Y-111835000D01* +X128605000Y-111645000D01* +X129745000Y-111645000D01* +X129745000Y-111835000D01* G37* G36* -X121395000Y-69005000D02* +X128795000Y-112405000D02* G01* -X121205000Y-69005000D01* -X121205000Y-68815000D01* -X121395000Y-68815000D01* -X121395000Y-69005000D01* +X128605000Y-112405000D01* +X128605000Y-112215000D01* +X128795000Y-112215000D01* +X128795000Y-112405000D01* G37* G36* -X121775000Y-69955000D02* +X129175000Y-113355000D02* G01* -X121205000Y-69955000D01* -X121205000Y-69765000D01* -X121775000Y-69765000D01* -X121775000Y-69955000D01* +X128605000Y-113355000D01* +X128605000Y-113165000D01* +X129175000Y-113165000D01* +X129175000Y-113355000D01* G37* G36* -X121775000Y-66915000D02* +X129175000Y-110315000D02* G01* -X121395000Y-66915000D01* -X121395000Y-66725000D01* -X121775000Y-66725000D01* -X121775000Y-66915000D01* +X128795000Y-110315000D01* +X128795000Y-110125000D01* +X129175000Y-110125000D01* +X129175000Y-110315000D01* G37* G36* -X121585000Y-67675000D02* +X128985000Y-111075000D02* G01* -X121395000Y-67675000D01* -X121395000Y-67485000D01* -X121585000Y-67485000D01* -X121585000Y-67675000D01* +X128795000Y-111075000D01* +X128795000Y-110885000D01* +X128985000Y-110885000D01* +X128985000Y-111075000D01* G37* G36* -X121775000Y-69765000D02* +X129175000Y-113165000D02* G01* -X121395000Y-69765000D01* -X121395000Y-69575000D01* -X121775000Y-69575000D01* -X121775000Y-69765000D01* +X128795000Y-113165000D01* +X128795000Y-112975000D01* +X129175000Y-112975000D01* +X129175000Y-113165000D01* G37* G36* -X121775000Y-64825000D02* +X129175000Y-108225000D02* G01* -X121585000Y-64825000D01* -X121585000Y-64635000D01* -X121775000Y-64635000D01* -X121775000Y-64825000D01* +X128985000Y-108225000D01* +X128985000Y-108035000D01* +X129175000Y-108035000D01* +X129175000Y-108225000D01* G37* G36* -X121775000Y-65015000D02* +X129175000Y-108415000D02* G01* -X121585000Y-65015000D01* -X121585000Y-64825000D01* -X121775000Y-64825000D01* -X121775000Y-65015000D01* +X128985000Y-108415000D01* +X128985000Y-108225000D01* +X129175000Y-108225000D01* +X129175000Y-108415000D01* G37* G36* -X121775000Y-65205000D02* +X129175000Y-108605000D02* G01* -X121585000Y-65205000D01* -X121585000Y-65015000D01* -X121775000Y-65015000D01* -X121775000Y-65205000D01* +X128985000Y-108605000D01* +X128985000Y-108415000D01* +X129175000Y-108415000D01* +X129175000Y-108605000D01* G37* G36* -X121775000Y-65395000D02* +X129175000Y-108795000D02* G01* -X121585000Y-65395000D01* -X121585000Y-65205000D01* -X121775000Y-65205000D01* -X121775000Y-65395000D01* +X128985000Y-108795000D01* +X128985000Y-108605000D01* +X129175000Y-108605000D01* +X129175000Y-108795000D01* G37* G36* -X121775000Y-65585000D02* +X129175000Y-108985000D02* G01* -X121585000Y-65585000D01* -X121585000Y-65395000D01* -X121775000Y-65395000D01* -X121775000Y-65585000D01* +X128985000Y-108985000D01* +X128985000Y-108795000D01* +X129175000Y-108795000D01* +X129175000Y-108985000D01* G37* G36* -X121775000Y-68245000D02* +X129175000Y-111645000D02* G01* -X121585000Y-68245000D01* -X121585000Y-68055000D01* -X121775000Y-68055000D01* -X121775000Y-68245000D01* +X128985000Y-111645000D01* +X128985000Y-111455000D01* +X129175000Y-111455000D01* +X129175000Y-111645000D01* G37* G36* -X121775000Y-68815000D02* +X129175000Y-112215000D02* G01* -X121585000Y-68815000D01* -X121585000Y-68625000D01* -X121775000Y-68625000D01* -X121775000Y-68815000D01* +X128985000Y-112215000D01* +X128985000Y-112025000D01* +X129175000Y-112025000D01* +X129175000Y-112215000D01* G37* G36* -X121965000Y-66345000D02* +X129365000Y-109745000D02* G01* -X121775000Y-66345000D01* -X121775000Y-66155000D01* -X121965000Y-66155000D01* -X121965000Y-66345000D01* +X129175000Y-109745000D01* +X129175000Y-109555000D01* +X129365000Y-109555000D01* +X129365000Y-109745000D01* G37* G36* -X122155000Y-66725000D02* +X129555000Y-110125000D02* G01* -X121775000Y-66725000D01* -X121775000Y-66535000D01* -X122155000Y-66535000D01* -X122155000Y-66725000D01* +X129175000Y-110125000D01* +X129175000Y-109935000D01* +X129555000Y-109935000D01* +X129555000Y-110125000D01* G37* G36* -X122155000Y-67295000D02* +X129555000Y-110695000D02* G01* -X121775000Y-67295000D01* -X121775000Y-67105000D01* -X122155000Y-67105000D01* -X122155000Y-67295000D01* +X129175000Y-110695000D01* +X129175000Y-110505000D01* +X129555000Y-110505000D01* +X129555000Y-110695000D01* G37* G36* -X121965000Y-67675000D02* +X129365000Y-111075000D02* G01* -X121775000Y-67675000D01* -X121775000Y-67485000D01* -X121965000Y-67485000D01* -X121965000Y-67675000D01* +X129175000Y-111075000D01* +X129175000Y-110885000D01* +X129365000Y-110885000D01* +X129365000Y-111075000D01* G37* G36* -X122345000Y-69385000D02* +X129745000Y-112785000D02* G01* -X121775000Y-69385000D01* -X121775000Y-69195000D01* -X122345000Y-69195000D01* -X122345000Y-69385000D01* +X129175000Y-112785000D01* +X129175000Y-112595000D01* +X129745000Y-112595000D01* +X129745000Y-112785000D01* G37* G36* -X122155000Y-64825000D02* +X129555000Y-108225000D02* G01* -X121965000Y-64825000D01* -X121965000Y-64635000D01* -X122155000Y-64635000D01* -X122155000Y-64825000D01* +X129365000Y-108225000D01* +X129365000Y-108035000D01* +X129555000Y-108035000D01* +X129555000Y-108225000D01* G37* G36* -X122155000Y-65015000D02* +X129555000Y-108415000D02* G01* -X121965000Y-65015000D01* -X121965000Y-64825000D01* -X122155000Y-64825000D01* -X122155000Y-65015000D01* +X129365000Y-108415000D01* +X129365000Y-108225000D01* +X129555000Y-108225000D01* +X129555000Y-108415000D01* G37* G36* -X122155000Y-65205000D02* +X129555000Y-108605000D02* G01* -X121965000Y-65205000D01* -X121965000Y-65015000D01* -X122155000Y-65015000D01* -X122155000Y-65205000D01* +X129365000Y-108605000D01* +X129365000Y-108415000D01* +X129555000Y-108415000D01* +X129555000Y-108605000D01* G37* G36* -X122345000Y-65395000D02* +X129745000Y-108795000D02* G01* -X121965000Y-65395000D01* -X121965000Y-65205000D01* -X122345000Y-65205000D01* -X122345000Y-65395000D01* +X129365000Y-108795000D01* +X129365000Y-108605000D01* +X129745000Y-108605000D01* +X129745000Y-108795000D01* G37* G36* -X122155000Y-65775000D02* +X129555000Y-109175000D02* G01* -X121965000Y-65775000D01* -X121965000Y-65585000D01* -X122155000Y-65585000D01* -X122155000Y-65775000D01* +X129365000Y-109175000D01* +X129365000Y-108985000D01* +X129555000Y-108985000D01* +X129555000Y-109175000D01* G37* G36* -X122535000Y-67105000D02* +X129935000Y-110505000D02* G01* -X121965000Y-67105000D01* -X121965000Y-66915000D01* -X122535000Y-66915000D01* -X122535000Y-67105000D01* +X129365000Y-110505000D01* +X129365000Y-110315000D01* +X129935000Y-110315000D01* +X129935000Y-110505000D01* G37* G36* -X122155000Y-68245000D02* +X129555000Y-111645000D02* G01* -X121965000Y-68245000D01* -X121965000Y-68055000D01* -X122155000Y-68055000D01* -X122155000Y-68245000D01* +X129365000Y-111645000D01* +X129365000Y-111455000D01* +X129555000Y-111455000D01* +X129555000Y-111645000D01* G37* G36* -X122155000Y-68625000D02* +X129555000Y-112025000D02* G01* -X121965000Y-68625000D01* -X121965000Y-68435000D01* -X122155000Y-68435000D01* -X122155000Y-68625000D01* +X129365000Y-112025000D01* +X129365000Y-111835000D01* +X129555000Y-111835000D01* +X129555000Y-112025000D01* G37* G36* -X123485000Y-68815000D02* +X130885000Y-112215000D02* G01* -X121965000Y-68815000D01* -X121965000Y-68625000D01* -X123485000Y-68625000D01* -X123485000Y-68815000D01* +X129365000Y-112215000D01* +X129365000Y-112025000D01* +X130885000Y-112025000D01* +X130885000Y-112215000D01* G37* G36* -X122535000Y-69005000D02* +X129935000Y-112405000D02* G01* -X121965000Y-69005000D01* -X121965000Y-68815000D01* -X122535000Y-68815000D01* -X122535000Y-69005000D01* +X129365000Y-112405000D01* +X129365000Y-112215000D01* +X129935000Y-112215000D01* +X129935000Y-112405000D01* G37* G36* -X122345000Y-64635000D02* +X129745000Y-108035000D02* G01* -X122155000Y-64635000D01* -X122155000Y-64445000D01* -X122345000Y-64445000D01* -X122345000Y-64635000D01* +X129555000Y-108035000D01* +X129555000Y-107845000D01* +X129745000Y-107845000D01* +X129745000Y-108035000D01* G37* G36* -X122345000Y-66155000D02* +X129745000Y-109555000D02* G01* -X122155000Y-66155000D01* -X122155000Y-65965000D01* -X122345000Y-65965000D01* -X122345000Y-66155000D01* +X129555000Y-109555000D01* +X129555000Y-109365000D01* +X129745000Y-109365000D01* +X129745000Y-109555000D01* G37* G36* -X122725000Y-66345000D02* +X130125000Y-109745000D02* G01* -X122155000Y-66345000D01* -X122155000Y-66155000D01* -X122725000Y-66155000D01* -X122725000Y-66345000D01* +X129555000Y-109745000D01* +X129555000Y-109555000D01* +X130125000Y-109555000D01* +X130125000Y-109745000D01* G37* G36* -X122345000Y-66915000D02* +X129745000Y-110315000D02* G01* -X122155000Y-66915000D01* -X122155000Y-66725000D01* -X122345000Y-66725000D01* -X122345000Y-66915000D01* +X129555000Y-110315000D01* +X129555000Y-110125000D01* +X129745000Y-110125000D01* +X129745000Y-110315000D01* G37* G36* -X122535000Y-67485000D02* +X129935000Y-110885000D02* G01* -X122155000Y-67485000D01* -X122155000Y-67295000D01* -X122535000Y-67295000D01* -X122535000Y-67485000D01* +X129555000Y-110885000D01* +X129555000Y-110695000D01* +X129935000Y-110695000D01* +X129935000Y-110885000D01* G37* G36* -X122345000Y-67675000D02* +X129745000Y-111075000D02* G01* -X122155000Y-67675000D01* -X122155000Y-67485000D01* -X122345000Y-67485000D01* -X122345000Y-67675000D01* +X129555000Y-111075000D01* +X129555000Y-110885000D01* +X129745000Y-110885000D01* +X129745000Y-111075000D01* G37* G36* -X122535000Y-67865000D02* +X129935000Y-111265000D02* G01* -X122155000Y-67865000D01* -X122155000Y-67675000D01* -X122535000Y-67675000D01* -X122535000Y-67865000D01* +X129555000Y-111265000D01* +X129555000Y-111075000D01* +X129935000Y-111075000D01* +X129935000Y-111265000D01* G37* G36* -X122345000Y-68055000D02* +X129745000Y-111455000D02* G01* -X122155000Y-68055000D01* -X122155000Y-67865000D01* -X122345000Y-67865000D01* -X122345000Y-68055000D01* +X129555000Y-111455000D01* +X129555000Y-111265000D01* +X129745000Y-111265000D01* +X129745000Y-111455000D01* G37* G36* -X122345000Y-69955000D02* +X129745000Y-113355000D02* G01* -X122155000Y-69955000D01* -X122155000Y-69765000D01* -X122345000Y-69765000D01* -X122345000Y-69955000D01* +X129555000Y-113355000D01* +X129555000Y-113165000D01* +X129745000Y-113165000D01* +X129745000Y-113355000D01* G37* G36* -X122535000Y-64825000D02* +X129935000Y-108225000D02* G01* -X122345000Y-64825000D01* -X122345000Y-64635000D01* -X122535000Y-64635000D01* -X122535000Y-64825000D01* +X129745000Y-108225000D01* +X129745000Y-108035000D01* +X129935000Y-108035000D01* +X129935000Y-108225000D01* G37* G36* -X122535000Y-65015000D02* +X129935000Y-108415000D02* G01* -X122345000Y-65015000D01* -X122345000Y-64825000D01* -X122535000Y-64825000D01* -X122535000Y-65015000D01* +X129745000Y-108415000D01* +X129745000Y-108225000D01* +X129935000Y-108225000D01* +X129935000Y-108415000D01* G37* G36* -X122535000Y-65775000D02* +X129935000Y-109175000D02* G01* -X122345000Y-65775000D01* -X122345000Y-65585000D01* -X122535000Y-65585000D01* -X122535000Y-65775000D01* +X129745000Y-109175000D01* +X129745000Y-108985000D01* +X129935000Y-108985000D01* +X129935000Y-109175000D01* G37* G36* -X122535000Y-66725000D02* +X129935000Y-110125000D02* G01* -X122345000Y-66725000D01* -X122345000Y-66535000D01* -X122535000Y-66535000D01* -X122535000Y-66725000D01* +X129745000Y-110125000D01* +X129745000Y-109935000D01* +X129935000Y-109935000D01* +X129935000Y-110125000D01* G37* G36* -X122725000Y-64635000D02* +X130125000Y-108035000D02* G01* -X122535000Y-64635000D01* -X122535000Y-64445000D01* -X122725000Y-64445000D01* -X122725000Y-64635000D01* +X129935000Y-108035000D01* +X129935000Y-107845000D01* +X130125000Y-107845000D01* +X130125000Y-108035000D01* G37* G36* -X123105000Y-65205000D02* +X130505000Y-108605000D02* G01* -X122535000Y-65205000D01* -X122535000Y-65015000D01* -X123105000Y-65015000D01* -X123105000Y-65205000D01* +X129935000Y-108605000D01* +X129935000Y-108415000D01* +X130505000Y-108415000D01* +X130505000Y-108605000D01* G37* G36* -X123485000Y-66155000D02* +X130885000Y-109555000D02* G01* -X122535000Y-66155000D01* -X122535000Y-65965000D01* -X123485000Y-65965000D01* -X123485000Y-66155000D01* +X129935000Y-109555000D01* +X129935000Y-109365000D01* +X130885000Y-109365000D01* +X130885000Y-109555000D01* G37* G36* -X123105000Y-66535000D02* +X130505000Y-109935000D02* G01* -X122535000Y-66535000D01* -X122535000Y-66345000D01* -X123105000Y-66345000D01* -X123105000Y-66535000D01* +X129935000Y-109935000D01* +X129935000Y-109745000D01* +X130505000Y-109745000D01* +X130505000Y-109935000D01* G37* G36* -X122725000Y-67675000D02* +X130125000Y-111075000D02* G01* -X122535000Y-67675000D01* -X122535000Y-67485000D01* -X122725000Y-67485000D01* -X122725000Y-67675000D01* +X129935000Y-111075000D01* +X129935000Y-110885000D01* +X130125000Y-110885000D01* +X130125000Y-111075000D01* G37* G36* -X122725000Y-68055000D02* +X130125000Y-111455000D02* G01* -X122535000Y-68055000D01* -X122535000Y-67865000D01* -X122725000Y-67865000D01* -X122725000Y-68055000D01* +X129935000Y-111455000D01* +X129935000Y-111265000D01* +X130125000Y-111265000D01* +X130125000Y-111455000D01* G37* G36* -X122725000Y-68435000D02* +X130125000Y-111835000D02* G01* -X122535000Y-68435000D01* -X122535000Y-68245000D01* -X122725000Y-68245000D01* -X122725000Y-68435000D01* +X129935000Y-111835000D01* +X129935000Y-111645000D01* +X130125000Y-111645000D01* +X130125000Y-111835000D01* G37* G36* -X122915000Y-69195000D02* +X130315000Y-112595000D02* G01* -X122535000Y-69195000D01* -X122535000Y-69005000D01* -X122915000Y-69005000D01* -X122915000Y-69195000D01* +X129935000Y-112595000D01* +X129935000Y-112405000D01* +X130315000Y-112405000D01* +X130315000Y-112595000D01* G37* G36* -X123295000Y-69575000D02* +X130695000Y-112975000D02* G01* -X122535000Y-69575000D01* -X122535000Y-69385000D01* -X123295000Y-69385000D01* -X123295000Y-69575000D01* +X129935000Y-112975000D01* +X129935000Y-112785000D01* +X130695000Y-112785000D01* +X130695000Y-112975000D01* G37* G36* -X122725000Y-69955000D02* +X130125000Y-113355000D02* G01* -X122535000Y-69955000D01* -X122535000Y-69765000D01* -X122725000Y-69765000D01* -X122725000Y-69955000D01* +X129935000Y-113355000D01* +X129935000Y-113165000D01* +X130125000Y-113165000D01* +X130125000Y-113355000D01* G37* G36* -X122915000Y-65015000D02* +X130315000Y-108415000D02* G01* -X122725000Y-65015000D01* -X122725000Y-64825000D01* -X122915000Y-64825000D01* -X122915000Y-65015000D01* +X130125000Y-108415000D01* +X130125000Y-108225000D01* +X130315000Y-108225000D01* +X130315000Y-108415000D01* G37* G36* -X122915000Y-65395000D02* +X130315000Y-108795000D02* G01* -X122725000Y-65395000D01* -X122725000Y-65205000D01* -X122915000Y-65205000D01* -X122915000Y-65395000D01* +X130125000Y-108795000D01* +X130125000Y-108605000D01* +X130315000Y-108605000D01* +X130315000Y-108795000D01* G37* G36* -X122915000Y-65585000D02* +X130315000Y-108985000D02* G01* -X122725000Y-65585000D01* -X122725000Y-65395000D01* -X122915000Y-65395000D01* -X122915000Y-65585000D01* +X130125000Y-108985000D01* +X130125000Y-108795000D01* +X130315000Y-108795000D01* +X130315000Y-108985000D01* G37* G36* -X122915000Y-65775000D02* +X130315000Y-109175000D02* G01* -X122725000Y-65775000D01* -X122725000Y-65585000D01* -X122915000Y-65585000D01* -X122915000Y-65775000D01* +X130125000Y-109175000D01* +X130125000Y-108985000D01* +X130315000Y-108985000D01* +X130315000Y-109175000D01* G37* G36* -X123295000Y-66725000D02* +X130695000Y-110125000D02* G01* -X122725000Y-66725000D01* -X122725000Y-66535000D01* -X123295000Y-66535000D01* -X123295000Y-66725000D01* +X130125000Y-110125000D01* +X130125000Y-109935000D01* +X130695000Y-109935000D01* +X130695000Y-110125000D01* G37* G36* -X122915000Y-66915000D02* +X130315000Y-110315000D02* G01* -X122725000Y-66915000D01* -X122725000Y-66725000D01* -X122915000Y-66725000D01* -X122915000Y-66915000D01* +X130125000Y-110315000D01* +X130125000Y-110125000D01* +X130315000Y-110125000D01* +X130315000Y-110315000D01* G37* G36* -X123105000Y-67865000D02* +X130505000Y-111265000D02* G01* -X122725000Y-67865000D01* -X122725000Y-67675000D01* -X123105000Y-67675000D01* -X123105000Y-67865000D01* +X130125000Y-111265000D01* +X130125000Y-111075000D01* +X130505000Y-111075000D01* +X130505000Y-111265000D01* G37* G36* -X122915000Y-69005000D02* +X130315000Y-112405000D02* G01* -X122725000Y-69005000D01* -X122725000Y-68815000D01* -X122915000Y-68815000D01* -X122915000Y-69005000D01* +X130125000Y-112405000D01* +X130125000Y-112215000D01* +X130315000Y-112215000D01* +X130315000Y-112405000D01* G37* G36* -X123295000Y-69385000D02* +X130695000Y-112785000D02* G01* -X122725000Y-69385000D01* -X122725000Y-69195000D01* -X123295000Y-69195000D01* -X123295000Y-69385000D01* +X130125000Y-112785000D01* +X130125000Y-112595000D01* +X130695000Y-112595000D01* +X130695000Y-112785000D01* G37* G36* -X123105000Y-65965000D02* +X130505000Y-109365000D02* G01* -X122915000Y-65965000D01* -X122915000Y-65775000D01* -X123105000Y-65775000D01* -X123105000Y-65965000D01* +X130315000Y-109365000D01* +X130315000Y-109175000D01* +X130505000Y-109175000D01* +X130505000Y-109365000D01* G37* G36* -X123105000Y-67105000D02* +X130505000Y-110505000D02* G01* -X122915000Y-67105000D01* -X122915000Y-66915000D01* -X123105000Y-66915000D01* -X123105000Y-67105000D01* +X130315000Y-110505000D01* +X130315000Y-110315000D01* +X130505000Y-110315000D01* +X130505000Y-110505000D01* G37* G36* -X123105000Y-67295000D02* +X130505000Y-110695000D02* G01* -X122915000Y-67295000D01* -X122915000Y-67105000D01* -X123105000Y-67105000D01* -X123105000Y-67295000D01* +X130315000Y-110695000D01* +X130315000Y-110505000D01* +X130505000Y-110505000D01* +X130505000Y-110695000D01* G37* G36* -X123105000Y-67485000D02* +X130505000Y-110885000D02* G01* -X122915000Y-67485000D01* -X122915000Y-67295000D01* -X123105000Y-67295000D01* -X123105000Y-67485000D01* +X130315000Y-110885000D01* +X130315000Y-110695000D01* +X130505000Y-110695000D01* +X130505000Y-110885000D01* G37* G36* -X123105000Y-68055000D02* +X130505000Y-111455000D02* G01* -X122915000Y-68055000D01* -X122915000Y-67865000D01* -X123105000Y-67865000D01* -X123105000Y-68055000D01* +X130315000Y-111455000D01* +X130315000Y-111265000D01* +X130505000Y-111265000D01* +X130505000Y-111455000D01* G37* G36* -X123865000Y-68435000D02* +X131265000Y-111835000D02* G01* -X122915000Y-68435000D01* -X122915000Y-68245000D01* -X123865000Y-68245000D01* -X123865000Y-68435000D01* +X130315000Y-111835000D01* +X130315000Y-111645000D01* +X131265000Y-111645000D01* +X131265000Y-111835000D01* G37* G36* -X123485000Y-68625000D02* +X130885000Y-112025000D02* G01* -X122915000Y-68625000D01* -X122915000Y-68435000D01* -X123485000Y-68435000D01* -X123485000Y-68625000D01* +X130315000Y-112025000D01* +X130315000Y-111835000D01* +X130885000Y-111835000D01* +X130885000Y-112025000D01* G37* G36* -X123295000Y-69765000D02* +X130695000Y-113165000D02* G01* -X122915000Y-69765000D01* -X122915000Y-69575000D01* -X123295000Y-69575000D01* -X123295000Y-69765000D01* +X130315000Y-113165000D01* +X130315000Y-112975000D01* +X130695000Y-112975000D01* +X130695000Y-113165000D01* G37* G36* -X123295000Y-64635000D02* +X130695000Y-108035000D02* G01* -X123105000Y-64635000D01* -X123105000Y-64445000D01* -X123295000Y-64445000D01* -X123295000Y-64635000D01* +X130505000Y-108035000D01* +X130505000Y-107845000D01* +X130695000Y-107845000D01* +X130695000Y-108035000D01* G37* G36* -X123295000Y-65015000D02* +X130695000Y-108415000D02* G01* -X123105000Y-65015000D01* -X123105000Y-64825000D01* -X123295000Y-64825000D01* -X123295000Y-65015000D01* +X130505000Y-108415000D01* +X130505000Y-108225000D01* +X130695000Y-108225000D01* +X130695000Y-108415000D01* G37* G36* -X123295000Y-65395000D02* +X130695000Y-108795000D02* G01* -X123105000Y-65395000D01* -X123105000Y-65205000D01* -X123295000Y-65205000D01* -X123295000Y-65395000D01* +X130505000Y-108795000D01* +X130505000Y-108605000D01* +X130695000Y-108605000D01* +X130695000Y-108795000D01* G37* G36* -X123295000Y-65775000D02* +X130695000Y-109175000D02* G01* -X123105000Y-65775000D01* -X123105000Y-65585000D01* -X123295000Y-65585000D01* -X123295000Y-65775000D01* +X130505000Y-109175000D01* +X130505000Y-108985000D01* +X130695000Y-108985000D01* +X130695000Y-109175000D01* G37* G36* -X124055000Y-67675000D02* +X131455000Y-111075000D02* G01* -X123105000Y-67675000D01* -X123105000Y-67485000D01* -X124055000Y-67485000D01* -X124055000Y-67675000D01* +X130505000Y-111075000D01* +X130505000Y-110885000D01* +X131455000Y-110885000D01* +X131455000Y-111075000D01* G37* G36* -X123295000Y-68245000D02* +X130695000Y-111645000D02* G01* -X123105000Y-68245000D01* -X123105000Y-68055000D01* -X123295000Y-68055000D01* -X123295000Y-68245000D01* +X130505000Y-111645000D01* +X130505000Y-111455000D01* +X130695000Y-111455000D01* +X130695000Y-111645000D01* G37* G36* -X123485000Y-69955000D02* +X130885000Y-113355000D02* G01* -X123105000Y-69955000D01* -X123105000Y-69765000D01* -X123485000Y-69765000D01* -X123485000Y-69955000D01* +X130505000Y-113355000D01* +X130505000Y-113165000D01* +X130885000Y-113165000D01* +X130885000Y-113355000D01* G37* G36* -X123485000Y-65205000D02* +X130885000Y-108605000D02* G01* -X123295000Y-65205000D01* -X123295000Y-65015000D01* -X123485000Y-65015000D01* -X123485000Y-65205000D01* +X130695000Y-108605000D01* +X130695000Y-108415000D01* +X130885000Y-108415000D01* +X130885000Y-108605000D01* G37* G36* -X123485000Y-66535000D02* +X130885000Y-109935000D02* G01* -X123295000Y-66535000D01* -X123295000Y-66345000D01* -X123485000Y-66345000D01* -X123485000Y-66535000D01* +X130695000Y-109935000D01* +X130695000Y-109745000D01* +X130885000Y-109745000D01* +X130885000Y-109935000D01* G37* G36* -X124435000Y-66915000D02* +X131835000Y-110315000D02* G01* -X123295000Y-66915000D01* -X123295000Y-66725000D01* -X124435000Y-66725000D01* -X124435000Y-66915000D01* +X130695000Y-110315000D01* +X130695000Y-110125000D01* +X131835000Y-110125000D01* +X131835000Y-110315000D01* G37* G36* -X123675000Y-67295000D02* +X131075000Y-110695000D02* G01* -X123295000Y-67295000D01* -X123295000Y-67105000D01* -X123675000Y-67105000D01* -X123675000Y-67295000D01* +X130695000Y-110695000D01* +X130695000Y-110505000D01* +X131075000Y-110505000D01* +X131075000Y-110695000D01* G37* G36* -X123485000Y-67865000D02* +X130885000Y-111265000D02* G01* -X123295000Y-67865000D01* -X123295000Y-67675000D01* -X123485000Y-67675000D01* -X123485000Y-67865000D01* +X130695000Y-111265000D01* +X130695000Y-111075000D01* +X130885000Y-111075000D01* +X130885000Y-111265000D01* G37* G36* -X124245000Y-64635000D02* +X131645000Y-108035000D02* G01* -X123485000Y-64635000D01* -X123485000Y-64445000D01* -X124245000Y-64445000D01* -X124245000Y-64635000D01* +X130885000Y-108035000D01* +X130885000Y-107845000D01* +X131645000Y-107845000D01* +X131645000Y-108035000D01* G37* G36* -X123865000Y-65015000D02* +X131265000Y-108415000D02* G01* -X123485000Y-65015000D01* -X123485000Y-64825000D01* -X123865000Y-64825000D01* -X123865000Y-65015000D01* +X130885000Y-108415000D01* +X130885000Y-108225000D01* +X131265000Y-108225000D01* +X131265000Y-108415000D01* G37* G36* -X123675000Y-65585000D02* +X131075000Y-108985000D02* G01* -X123485000Y-65585000D01* -X123485000Y-65395000D01* -X123675000Y-65395000D01* -X123675000Y-65585000D01* +X130885000Y-108985000D01* +X130885000Y-108795000D01* +X131075000Y-108795000D01* +X131075000Y-108985000D01* G37* G36* -X123675000Y-65775000D02* +X131075000Y-109175000D02* G01* -X123485000Y-65775000D01* -X123485000Y-65585000D01* -X123675000Y-65585000D01* -X123675000Y-65775000D01* +X130885000Y-109175000D01* +X130885000Y-108985000D01* +X131075000Y-108985000D01* +X131075000Y-109175000D01* G37* G36* -X123865000Y-65965000D02* +X131265000Y-109365000D02* G01* -X123485000Y-65965000D01* -X123485000Y-65775000D01* -X123865000Y-65775000D01* -X123865000Y-65965000D01* +X130885000Y-109365000D01* +X130885000Y-109175000D01* +X131265000Y-109175000D01* +X131265000Y-109365000D01* G37* G36* -X124435000Y-68055000D02* +X131835000Y-111455000D02* G01* -X123485000Y-68055000D01* -X123485000Y-67865000D01* -X124435000Y-67865000D01* -X124435000Y-68055000D01* +X130885000Y-111455000D01* +X130885000Y-111265000D01* +X131835000Y-111265000D01* +X131835000Y-111455000D01* G37* G36* -X123675000Y-69195000D02* +X131075000Y-112595000D02* G01* -X123485000Y-69195000D01* -X123485000Y-69005000D01* -X123675000Y-69005000D01* -X123675000Y-69195000D01* +X130885000Y-112595000D01* +X130885000Y-112405000D01* +X131075000Y-112405000D01* +X131075000Y-112595000D01* G37* G36* -X123675000Y-69575000D02* +X131075000Y-112975000D02* G01* -X123485000Y-69575000D01* -X123485000Y-69385000D01* -X123675000Y-69385000D01* -X123675000Y-69575000D01* +X130885000Y-112975000D01* +X130885000Y-112785000D01* +X131075000Y-112785000D01* +X131075000Y-112975000D01* G37* G36* -X123865000Y-69765000D02* +X131265000Y-113165000D02* G01* -X123485000Y-69765000D01* -X123485000Y-69575000D01* -X123865000Y-69575000D01* -X123865000Y-69765000D01* +X130885000Y-113165000D01* +X130885000Y-112975000D01* +X131265000Y-112975000D01* +X131265000Y-113165000D01* G37* G36* -X123865000Y-65395000D02* +X131265000Y-108795000D02* G01* -X123675000Y-65395000D01* -X123675000Y-65205000D01* -X123865000Y-65205000D01* -X123865000Y-65395000D01* +X131075000Y-108795000D01* +X131075000Y-108605000D01* +X131265000Y-108605000D01* +X131265000Y-108795000D01* G37* G36* -X124055000Y-66345000D02* +X131455000Y-109745000D02* G01* -X123675000Y-66345000D01* -X123675000Y-66155000D01* -X124055000Y-66155000D01* -X124055000Y-66345000D01* +X131075000Y-109745000D01* +X131075000Y-109555000D01* +X131455000Y-109555000D01* +X131455000Y-109745000D01* G37* G36* -X124055000Y-67105000D02* +X131455000Y-110505000D02* G01* -X123675000Y-67105000D01* -X123675000Y-66915000D01* -X124055000Y-66915000D01* -X124055000Y-67105000D01* +X131075000Y-110505000D01* +X131075000Y-110315000D01* +X131455000Y-110315000D01* +X131455000Y-110505000D01* G37* G36* -X124625000Y-67865000D02* +X132025000Y-111265000D02* G01* -X123675000Y-67865000D01* -X123675000Y-67675000D01* -X124625000Y-67675000D01* -X124625000Y-67865000D01* +X131075000Y-111265000D01* +X131075000Y-111075000D01* +X132025000Y-111075000D01* +X132025000Y-111265000D01* G37* G36* -X123865000Y-68625000D02* +X131265000Y-112025000D02* G01* -X123675000Y-68625000D01* -X123675000Y-68435000D01* -X123865000Y-68435000D01* -X123865000Y-68625000D01* +X131075000Y-112025000D01* +X131075000Y-111835000D01* +X131265000Y-111835000D01* +X131265000Y-112025000D01* G37* G36* -X124435000Y-69005000D02* +X131835000Y-112405000D02* G01* -X123675000Y-69005000D01* -X123675000Y-68815000D01* -X124435000Y-68815000D01* -X124435000Y-69005000D01* +X131075000Y-112405000D01* +X131075000Y-112215000D01* +X131835000Y-112215000D01* +X131835000Y-112405000D01* G37* G36* -X123865000Y-69385000D02* +X131265000Y-112785000D02* G01* -X123675000Y-69385000D01* -X123675000Y-69195000D01* -X123865000Y-69195000D01* -X123865000Y-69385000D01* +X131075000Y-112785000D01* +X131075000Y-112595000D01* +X131265000Y-112595000D01* +X131265000Y-112785000D01* G37* G36* -X124055000Y-65205000D02* +X131455000Y-108605000D02* G01* -X123865000Y-65205000D01* -X123865000Y-65015000D01* -X124055000Y-65015000D01* -X124055000Y-65205000D01* +X131265000Y-108605000D01* +X131265000Y-108415000D01* +X131455000Y-108415000D01* +X131455000Y-108605000D01* G37* G36* -X124245000Y-65585000D02* +X131645000Y-108985000D02* G01* -X123865000Y-65585000D01* -X123865000Y-65395000D01* -X124245000Y-65395000D01* -X124245000Y-65585000D01* +X131265000Y-108985000D01* +X131265000Y-108795000D01* +X131645000Y-108795000D01* +X131645000Y-108985000D01* G37* G36* -X124055000Y-65775000D02* +X131455000Y-109175000D02* G01* -X123865000Y-65775000D01* -X123865000Y-65585000D01* -X124055000Y-65585000D01* -X124055000Y-65775000D01* +X131265000Y-109175000D01* +X131265000Y-108985000D01* +X131455000Y-108985000D01* +X131455000Y-109175000D01* G37* G36* -X124245000Y-66155000D02* +X131645000Y-109555000D02* G01* -X123865000Y-66155000D01* -X123865000Y-65965000D01* -X124245000Y-65965000D01* -X124245000Y-66155000D01* +X131265000Y-109555000D01* +X131265000Y-109365000D01* +X131645000Y-109365000D01* +X131645000Y-109555000D01* G37* G36* -X124055000Y-66725000D02* +X131455000Y-110125000D02* G01* -X123865000Y-66725000D01* -X123865000Y-66535000D01* -X124055000Y-66535000D01* -X124055000Y-66725000D01* +X131265000Y-110125000D01* +X131265000Y-109935000D01* +X131455000Y-109935000D01* +X131455000Y-110125000D01* G37* G36* -X124245000Y-67485000D02* +X131645000Y-110885000D02* G01* -X123865000Y-67485000D01* -X123865000Y-67295000D01* -X124245000Y-67295000D01* -X124245000Y-67485000D01* +X131265000Y-110885000D01* +X131265000Y-110695000D01* +X131645000Y-110695000D01* +X131645000Y-110885000D01* G37* G36* -X124435000Y-68815000D02* +X131835000Y-112215000D02* G01* -X123865000Y-68815000D01* -X123865000Y-68625000D01* -X124435000Y-68625000D01* -X124435000Y-68815000D01* +X131265000Y-112215000D01* +X131265000Y-112025000D01* +X131835000Y-112025000D01* +X131835000Y-112215000D01* G37* G36* -X124435000Y-69955000D02* +X131835000Y-113355000D02* G01* -X123865000Y-69955000D01* -X123865000Y-69765000D01* -X124435000Y-69765000D01* -X124435000Y-69955000D01* +X131265000Y-113355000D01* +X131265000Y-113165000D01* +X131835000Y-113165000D01* +X131835000Y-113355000D01* G37* G36* -X124245000Y-65015000D02* +X131645000Y-108415000D02* G01* -X124055000Y-65015000D01* -X124055000Y-64825000D01* -X124245000Y-64825000D01* -X124245000Y-65015000D01* +X131455000Y-108415000D01* +X131455000Y-108225000D01* +X131645000Y-108225000D01* +X131645000Y-108415000D01* G37* G36* -X124245000Y-65965000D02* +X131645000Y-109365000D02* G01* -X124055000Y-65965000D01* -X124055000Y-65775000D01* -X124245000Y-65775000D01* -X124245000Y-65965000D01* +X131455000Y-109365000D01* +X131455000Y-109175000D01* +X131645000Y-109175000D01* +X131645000Y-109365000D01* G37* G36* -X124435000Y-66535000D02* +X131835000Y-109935000D02* G01* -X124055000Y-66535000D01* -X124055000Y-66345000D01* -X124435000Y-66345000D01* -X124435000Y-66535000D01* +X131455000Y-109935000D01* +X131455000Y-109745000D01* +X131835000Y-109745000D01* +X131835000Y-109935000D01* G37* G36* -X124245000Y-68245000D02* +X131645000Y-111645000D02* G01* -X124055000Y-68245000D01* -X124055000Y-68055000D01* -X124245000Y-68055000D01* -X124245000Y-68245000D01* +X131455000Y-111645000D01* +X131455000Y-111455000D01* +X131645000Y-111455000D01* +X131645000Y-111645000D01* G37* G36* -X124245000Y-68435000D02* +X131645000Y-111835000D02* G01* -X124055000Y-68435000D01* -X124055000Y-68245000D01* -X124245000Y-68245000D01* -X124245000Y-68435000D01* +X131455000Y-111835000D01* +X131455000Y-111645000D01* +X131645000Y-111645000D01* +X131645000Y-111835000D01* G37* G36* -X124245000Y-69195000D02* +X131645000Y-112595000D02* G01* -X124055000Y-69195000D01* -X124055000Y-69005000D01* -X124245000Y-69005000D01* -X124245000Y-69195000D01* +X131455000Y-112595000D01* +X131455000Y-112405000D01* +X131645000Y-112405000D01* +X131645000Y-112595000D01* G37* G36* -X124245000Y-69385000D02* +X131645000Y-112785000D02* G01* -X124055000Y-69385000D01* -X124055000Y-69195000D01* -X124245000Y-69195000D01* -X124245000Y-69385000D01* +X131455000Y-112785000D01* +X131455000Y-112595000D01* +X131645000Y-112595000D01* +X131645000Y-112785000D01* G37* G36* -X124245000Y-69575000D02* +X131645000Y-112975000D02* G01* -X124055000Y-69575000D01* -X124055000Y-69385000D01* -X124245000Y-69385000D01* -X124245000Y-69575000D01* +X131455000Y-112975000D01* +X131455000Y-112785000D01* +X131645000Y-112785000D01* +X131645000Y-112975000D01* G37* G36* -X124435000Y-69765000D02* +X131835000Y-113165000D02* G01* -X124055000Y-69765000D01* -X124055000Y-69575000D01* -X124435000Y-69575000D01* -X124435000Y-69765000D01* +X131455000Y-113165000D01* +X131455000Y-112975000D01* +X131835000Y-112975000D01* +X131835000Y-113165000D01* G37* G36* -X124435000Y-65205000D02* +X131835000Y-108605000D02* G01* -X124245000Y-65205000D01* -X124245000Y-65015000D01* -X124435000Y-65015000D01* -X124435000Y-65205000D01* +X131645000Y-108605000D01* +X131645000Y-108415000D01* +X131835000Y-108415000D01* +X131835000Y-108605000D01* G37* G36* -X124435000Y-65395000D02* +X131835000Y-108795000D02* G01* -X124245000Y-65395000D01* -X124245000Y-65205000D01* -X124435000Y-65205000D01* -X124435000Y-65395000D01* +X131645000Y-108795000D01* +X131645000Y-108605000D01* +X131835000Y-108605000D01* +X131835000Y-108795000D01* G37* G36* -X124435000Y-65775000D02* +X131835000Y-109175000D02* G01* -X124245000Y-65775000D01* -X124245000Y-65585000D01* -X124435000Y-65585000D01* -X124435000Y-65775000D01* +X131645000Y-109175000D01* +X131645000Y-108985000D01* +X131835000Y-108985000D01* +X131835000Y-109175000D01* G37* G36* -X124435000Y-66725000D02* +X131835000Y-110125000D02* G01* -X124245000Y-66725000D01* -X124245000Y-66535000D01* -X124435000Y-66535000D01* -X124435000Y-66725000D01* +X131645000Y-110125000D01* +X131645000Y-109935000D01* +X131835000Y-109935000D01* +X131835000Y-110125000D01* G37* G36* -X124625000Y-67105000D02* +X132025000Y-110505000D02* G01* -X124245000Y-67105000D01* -X124245000Y-66915000D01* -X124625000Y-66915000D01* -X124625000Y-67105000D01* +X131645000Y-110505000D01* +X131645000Y-110315000D01* +X132025000Y-110315000D01* +X132025000Y-110505000D01* G37* G36* -X124435000Y-68625000D02* +X131835000Y-112025000D02* G01* -X124245000Y-68625000D01* -X124245000Y-68435000D01* -X124435000Y-68435000D01* -X124435000Y-68625000D01* +X131645000Y-112025000D01* +X131645000Y-111835000D01* +X131835000Y-111835000D01* +X131835000Y-112025000D01* G37* G36* -X125005000Y-66155000D02* +X132405000Y-109555000D02* G01* -X124435000Y-66155000D01* -X124435000Y-65965000D01* -X125005000Y-65965000D01* -X125005000Y-66155000D01* +X131835000Y-109555000D01* +X131835000Y-109365000D01* +X132405000Y-109365000D01* +X132405000Y-109555000D01* G37* G36* -X124625000Y-66345000D02* +X132025000Y-109745000D02* G01* -X124435000Y-66345000D01* -X124435000Y-66155000D01* -X124625000Y-66155000D01* -X124625000Y-66345000D01* +X131835000Y-109745000D01* +X131835000Y-109555000D01* +X132025000Y-109555000D01* +X132025000Y-109745000D01* G37* G36* -X125195000Y-67295000D02* +X132595000Y-110695000D02* G01* -X124435000Y-67295000D01* -X124435000Y-67105000D01* -X125195000Y-67105000D01* -X125195000Y-67295000D01* +X131835000Y-110695000D01* +X131835000Y-110505000D01* +X132595000Y-110505000D01* +X132595000Y-110695000D01* G37* G36* -X124815000Y-68435000D02* +X132215000Y-111835000D02* G01* -X124435000Y-68435000D01* -X124435000Y-68245000D01* -X124815000Y-68245000D01* -X124815000Y-68435000D01* +X131835000Y-111835000D01* +X131835000Y-111645000D01* +X132215000Y-111645000D01* +X132215000Y-111835000D01* G37* G36* -X125955000Y-64635000D02* +X133355000Y-108035000D02* G01* -X124625000Y-64635000D01* -X124625000Y-64445000D01* -X125955000Y-64445000D01* -X125955000Y-64635000D01* +X132025000Y-108035000D01* +X132025000Y-107845000D01* +X133355000Y-107845000D01* +X133355000Y-108035000D01* G37* G36* -X124815000Y-64825000D02* +X132215000Y-108225000D02* G01* -X124625000Y-64825000D01* -X124625000Y-64635000D01* -X124815000Y-64635000D01* -X124815000Y-64825000D01* +X132025000Y-108225000D01* +X132025000Y-108035000D01* +X132215000Y-108035000D01* +X132215000Y-108225000D01* G37* G36* -X124815000Y-65015000D02* +X132215000Y-108415000D02* G01* -X124625000Y-65015000D01* -X124625000Y-64825000D01* -X124815000Y-64825000D01* -X124815000Y-65015000D01* +X132025000Y-108415000D01* +X132025000Y-108225000D01* +X132215000Y-108225000D01* +X132215000Y-108415000D01* G37* G36* -X124815000Y-65205000D02* +X132215000Y-108605000D02* G01* -X124625000Y-65205000D01* -X124625000Y-65015000D01* -X124815000Y-65015000D01* -X124815000Y-65205000D01* +X132025000Y-108605000D01* +X132025000Y-108415000D01* +X132215000Y-108415000D01* +X132215000Y-108605000D01* G37* G36* -X124815000Y-65395000D02* +X132215000Y-108795000D02* G01* -X124625000Y-65395000D01* -X124625000Y-65205000D01* -X124815000Y-65205000D01* -X124815000Y-65395000D01* +X132025000Y-108795000D01* +X132025000Y-108605000D01* +X132215000Y-108605000D01* +X132215000Y-108795000D01* G37* G36* -X124815000Y-65585000D02* +X132215000Y-108985000D02* G01* -X124625000Y-65585000D01* -X124625000Y-65395000D01* -X124815000Y-65395000D01* -X124815000Y-65585000D01* +X132025000Y-108985000D01* +X132025000Y-108795000D01* +X132215000Y-108795000D01* +X132215000Y-108985000D01* G37* G36* -X125955000Y-65775000D02* +X133355000Y-109175000D02* G01* -X124625000Y-65775000D01* -X124625000Y-65585000D01* -X125955000Y-65585000D01* -X125955000Y-65775000D01* +X132025000Y-109175000D01* +X132025000Y-108985000D01* +X133355000Y-108985000D01* +X133355000Y-109175000D01* G37* G36* -X124815000Y-66535000D02* +X132215000Y-109935000D02* G01* -X124625000Y-66535000D01* -X124625000Y-66345000D01* -X124815000Y-66345000D01* -X124815000Y-66535000D01* +X132025000Y-109935000D01* +X132025000Y-109745000D01* +X132215000Y-109745000D01* +X132215000Y-109935000D01* G37* G36* -X125765000Y-66915000D02* +X133165000Y-110315000D02* G01* -X124625000Y-66915000D01* -X124625000Y-66725000D01* -X125765000Y-66725000D01* -X125765000Y-66915000D01* +X132025000Y-110315000D01* +X132025000Y-110125000D01* +X133165000Y-110125000D01* +X133165000Y-110315000D01* G37* G36* -X124815000Y-67675000D02* +X132215000Y-111075000D02* G01* -X124625000Y-67675000D01* -X124625000Y-67485000D01* -X124815000Y-67485000D01* -X124815000Y-67675000D01* +X132025000Y-111075000D01* +X132025000Y-110885000D01* +X132215000Y-110885000D01* +X132215000Y-111075000D01* G37* G36* -X125005000Y-68055000D02* +X132405000Y-111455000D02* G01* -X124625000Y-68055000D01* -X124625000Y-67865000D01* -X125005000Y-67865000D01* -X125005000Y-68055000D01* +X132025000Y-111455000D01* +X132025000Y-111265000D01* +X132405000Y-111265000D01* +X132405000Y-111455000D01* G37* G36* -X125955000Y-68815000D02* +X133355000Y-112215000D02* G01* -X124625000Y-68815000D01* -X124625000Y-68625000D01* -X125955000Y-68625000D01* -X125955000Y-68815000D01* +X132025000Y-112215000D01* +X132025000Y-112025000D01* +X133355000Y-112025000D01* +X133355000Y-112215000D01* G37* G36* -X124815000Y-69005000D02* +X132215000Y-112405000D02* G01* -X124625000Y-69005000D01* -X124625000Y-68815000D01* -X124815000Y-68815000D01* -X124815000Y-69005000D01* +X132025000Y-112405000D01* +X132025000Y-112215000D01* +X132215000Y-112215000D01* +X132215000Y-112405000D01* G37* G36* -X124815000Y-69195000D02* +X132215000Y-112595000D02* G01* -X124625000Y-69195000D01* -X124625000Y-69005000D01* -X124815000Y-69005000D01* -X124815000Y-69195000D01* +X132025000Y-112595000D01* +X132025000Y-112405000D01* +X132215000Y-112405000D01* +X132215000Y-112595000D01* G37* G36* -X124815000Y-69385000D02* +X132215000Y-112785000D02* G01* -X124625000Y-69385000D01* -X124625000Y-69195000D01* -X124815000Y-69195000D01* -X124815000Y-69385000D01* +X132025000Y-112785000D01* +X132025000Y-112595000D01* +X132215000Y-112595000D01* +X132215000Y-112785000D01* G37* G36* -X124815000Y-69575000D02* +X132215000Y-112975000D02* G01* -X124625000Y-69575000D01* -X124625000Y-69385000D01* -X124815000Y-69385000D01* -X124815000Y-69575000D01* +X132025000Y-112975000D01* +X132025000Y-112785000D01* +X132215000Y-112785000D01* +X132215000Y-112975000D01* G37* G36* -X124815000Y-69765000D02* +X132215000Y-113165000D02* G01* -X124625000Y-69765000D01* -X124625000Y-69575000D01* -X124815000Y-69575000D01* -X124815000Y-69765000D01* +X132025000Y-113165000D01* +X132025000Y-112975000D01* +X132215000Y-112975000D01* +X132215000Y-113165000D01* G37* G36* -X125955000Y-69955000D02* +X133355000Y-113355000D02* G01* -X124625000Y-69955000D01* -X124625000Y-69765000D01* -X125955000Y-69765000D01* -X125955000Y-69955000D01* +X132025000Y-113355000D01* +X132025000Y-113165000D01* +X133355000Y-113165000D01* +X133355000Y-113355000D01* G37* G36* -X125765000Y-66345000D02* +X133165000Y-109745000D02* G01* -X124815000Y-66345000D01* -X124815000Y-66155000D01* -X125765000Y-66155000D01* -X125765000Y-66345000D01* +X132215000Y-109745000D01* +X132215000Y-109555000D01* +X133165000Y-109555000D01* +X133165000Y-109745000D01* G37* G36* -X125005000Y-67485000D02* +X132405000Y-110885000D02* G01* -X124815000Y-67485000D01* -X124815000Y-67295000D01* -X125005000Y-67295000D01* -X125005000Y-67485000D01* +X132215000Y-110885000D01* +X132215000Y-110695000D01* +X132405000Y-110695000D01* +X132405000Y-110885000D01* G37* G36* -X125005000Y-67865000D02* +X132405000Y-111265000D02* G01* -X124815000Y-67865000D01* -X124815000Y-67675000D01* -X125005000Y-67675000D01* -X125005000Y-67865000D01* +X132215000Y-111265000D01* +X132215000Y-111075000D01* +X132405000Y-111075000D01* +X132405000Y-111265000D01* G37* G36* -X125575000Y-65015000D02* +X132975000Y-108415000D02* G01* -X125005000Y-65015000D01* -X125005000Y-64825000D01* -X125575000Y-64825000D01* -X125575000Y-65015000D01* +X132405000Y-108415000D01* +X132405000Y-108225000D01* +X132975000Y-108225000D01* +X132975000Y-108415000D01* G37* G36* -X125575000Y-65205000D02* +X132975000Y-108605000D02* G01* -X125005000Y-65205000D01* -X125005000Y-65015000D01* -X125575000Y-65015000D01* -X125575000Y-65205000D01* +X132405000Y-108605000D01* +X132405000Y-108415000D01* +X132975000Y-108415000D01* +X132975000Y-108605000D01* G37* G36* -X125575000Y-65395000D02* +X132975000Y-108795000D02* G01* -X125005000Y-65395000D01* -X125005000Y-65205000D01* -X125575000Y-65205000D01* -X125575000Y-65395000D01* +X132405000Y-108795000D01* +X132405000Y-108605000D01* +X132975000Y-108605000D01* +X132975000Y-108795000D01* G37* G36* -X125195000Y-66725000D02* +X132595000Y-110125000D02* G01* -X125005000Y-66725000D01* -X125005000Y-66535000D01* -X125195000Y-66535000D01* -X125195000Y-66725000D01* +X132405000Y-110125000D01* +X132405000Y-109935000D01* +X132595000Y-109935000D01* +X132595000Y-110125000D01* G37* G36* -X125575000Y-67105000D02* +X132975000Y-110505000D02* G01* -X125005000Y-67105000D01* -X125005000Y-66915000D01* -X125575000Y-66915000D01* -X125575000Y-67105000D01* +X132405000Y-110505000D01* +X132405000Y-110315000D01* +X132975000Y-110315000D01* +X132975000Y-110505000D01* G37* G36* -X125195000Y-67675000D02* +X132595000Y-111075000D02* G01* -X125005000Y-67675000D01* -X125005000Y-67485000D01* -X125195000Y-67485000D01* -X125195000Y-67675000D01* +X132405000Y-111075000D01* +X132405000Y-110885000D01* +X132595000Y-110885000D01* +X132595000Y-111075000D01* G37* G36* -X125575000Y-68435000D02* +X132975000Y-111835000D02* G01* -X125005000Y-68435000D01* -X125005000Y-68245000D01* -X125575000Y-68245000D01* -X125575000Y-68435000D01* +X132405000Y-111835000D01* +X132405000Y-111645000D01* +X132975000Y-111645000D01* +X132975000Y-111835000D01* G37* G36* -X125575000Y-69195000D02* +X132975000Y-112595000D02* G01* -X125005000Y-69195000D01* -X125005000Y-69005000D01* -X125575000Y-69005000D01* -X125575000Y-69195000D01* +X132405000Y-112595000D01* +X132405000Y-112405000D01* +X132975000Y-112405000D01* +X132975000Y-112595000D01* G37* G36* -X125575000Y-69385000D02* +X132975000Y-112785000D02* G01* -X125005000Y-69385000D01* -X125005000Y-69195000D01* -X125575000Y-69195000D01* -X125575000Y-69385000D01* +X132405000Y-112785000D01* +X132405000Y-112595000D01* +X132975000Y-112595000D01* +X132975000Y-112785000D01* G37* G36* -X125575000Y-69575000D02* +X132975000Y-112975000D02* G01* -X125005000Y-69575000D01* -X125005000Y-69385000D01* -X125575000Y-69385000D01* -X125575000Y-69575000D01* +X132405000Y-112975000D01* +X132405000Y-112785000D01* +X132975000Y-112785000D01* +X132975000Y-112975000D01* G37* G36* -X125575000Y-66725000D02* +X132975000Y-110125000D02* G01* -X125385000Y-66725000D01* -X125385000Y-66535000D01* -X125575000Y-66535000D01* -X125575000Y-66725000D01* +X132785000Y-110125000D01* +X132785000Y-109935000D01* +X132975000Y-109935000D01* +X132975000Y-110125000D01* G37* G36* -X125575000Y-67485000D02* +X132975000Y-110885000D02* G01* -X125385000Y-67485000D01* -X125385000Y-67295000D01* -X125575000Y-67295000D01* -X125575000Y-67485000D01* +X132785000Y-110885000D01* +X132785000Y-110695000D01* +X132975000Y-110695000D01* +X132975000Y-110885000D01* G37* G36* -X125955000Y-67865000D02* +X133355000Y-111265000D02* G01* -X125385000Y-67865000D01* -X125385000Y-67675000D01* -X125955000Y-67675000D01* -X125955000Y-67865000D01* +X132785000Y-111265000D01* +X132785000Y-111075000D01* +X133355000Y-111075000D01* +X133355000Y-111265000D01* G37* G36* -X125955000Y-68055000D02* +X133355000Y-111455000D02* G01* -X125385000Y-68055000D01* -X125385000Y-67865000D01* -X125955000Y-67865000D01* -X125955000Y-68055000D01* +X132785000Y-111455000D01* +X132785000Y-111265000D01* +X133355000Y-111265000D01* +X133355000Y-111455000D01* G37* G36* -X125955000Y-66155000D02* +X133355000Y-109555000D02* G01* -X125575000Y-66155000D01* -X125575000Y-65965000D01* -X125955000Y-65965000D01* -X125955000Y-66155000D01* +X132975000Y-109555000D01* +X132975000Y-109365000D01* +X133355000Y-109365000D01* +X133355000Y-109555000D01* G37* G36* -X125765000Y-66535000D02* +X133165000Y-109935000D02* G01* -X125575000Y-66535000D01* -X125575000Y-66345000D01* -X125765000Y-66345000D01* -X125765000Y-66535000D01* +X132975000Y-109935000D01* +X132975000Y-109745000D01* +X133165000Y-109745000D01* +X133165000Y-109935000D01* G37* G36* -X125765000Y-67295000D02* +X133165000Y-110695000D02* G01* -X125575000Y-67295000D01* -X125575000Y-67105000D01* -X125765000Y-67105000D01* -X125765000Y-67295000D01* +X132975000Y-110695000D01* +X132975000Y-110505000D01* +X133165000Y-110505000D01* +X133165000Y-110695000D01* G37* G36* -X125955000Y-67675000D02* +X133355000Y-111075000D02* G01* -X125575000Y-67675000D01* -X125575000Y-67485000D01* -X125955000Y-67485000D01* -X125955000Y-67675000D01* +X132975000Y-111075000D01* +X132975000Y-110885000D01* +X133355000Y-110885000D01* +X133355000Y-111075000D01* G37* G36* -X125955000Y-64825000D02* +X133355000Y-108225000D02* G01* -X125765000Y-64825000D01* -X125765000Y-64635000D01* -X125955000Y-64635000D01* -X125955000Y-64825000D01* +X133165000Y-108225000D01* +X133165000Y-108035000D01* +X133355000Y-108035000D01* +X133355000Y-108225000D01* G37* G36* -X125955000Y-65015000D02* +X133355000Y-108415000D02* G01* -X125765000Y-65015000D01* -X125765000Y-64825000D01* -X125955000Y-64825000D01* -X125955000Y-65015000D01* +X133165000Y-108415000D01* +X133165000Y-108225000D01* +X133355000Y-108225000D01* +X133355000Y-108415000D01* G37* G36* -X125955000Y-65205000D02* +X133355000Y-108605000D02* G01* -X125765000Y-65205000D01* -X125765000Y-65015000D01* -X125955000Y-65015000D01* -X125955000Y-65205000D01* +X133165000Y-108605000D01* +X133165000Y-108415000D01* +X133355000Y-108415000D01* +X133355000Y-108605000D01* G37* G36* -X125955000Y-65395000D02* +X133355000Y-108795000D02* G01* -X125765000Y-65395000D01* -X125765000Y-65205000D01* -X125955000Y-65205000D01* -X125955000Y-65395000D01* +X133165000Y-108795000D01* +X133165000Y-108605000D01* +X133355000Y-108605000D01* +X133355000Y-108795000D01* G37* G36* -X125955000Y-65585000D02* +X133355000Y-108985000D02* G01* -X125765000Y-65585000D01* -X125765000Y-65395000D01* -X125955000Y-65395000D01* -X125955000Y-65585000D01* +X133165000Y-108985000D01* +X133165000Y-108795000D01* +X133355000Y-108795000D01* +X133355000Y-108985000D01* G37* G36* -X125955000Y-66725000D02* +X133355000Y-110125000D02* G01* -X125765000Y-66725000D01* -X125765000Y-66535000D01* -X125955000Y-66535000D01* -X125955000Y-66725000D01* +X133165000Y-110125000D01* +X133165000Y-109935000D01* +X133355000Y-109935000D01* +X133355000Y-110125000D01* G37* G36* -X125955000Y-68245000D02* +X133355000Y-111645000D02* G01* -X125765000Y-68245000D01* -X125765000Y-68055000D01* -X125955000Y-68055000D01* -X125955000Y-68245000D01* +X133165000Y-111645000D01* +X133165000Y-111455000D01* +X133355000Y-111455000D01* +X133355000Y-111645000D01* G37* G36* -X125955000Y-68435000D02* +X133355000Y-111835000D02* G01* -X125765000Y-68435000D01* -X125765000Y-68245000D01* -X125955000Y-68245000D01* -X125955000Y-68435000D01* +X133165000Y-111835000D01* +X133165000Y-111645000D01* +X133355000Y-111645000D01* +X133355000Y-111835000D01* G37* G36* -X125955000Y-69005000D02* +X133355000Y-112405000D02* G01* -X125765000Y-69005000D01* -X125765000Y-68815000D01* -X125955000Y-68815000D01* -X125955000Y-69005000D01* +X133165000Y-112405000D01* +X133165000Y-112215000D01* +X133355000Y-112215000D01* +X133355000Y-112405000D01* G37* G36* -X125955000Y-69195000D02* +X133355000Y-112595000D02* G01* -X125765000Y-69195000D01* -X125765000Y-69005000D01* -X125955000Y-69005000D01* -X125955000Y-69195000D01* +X133165000Y-112595000D01* +X133165000Y-112405000D01* +X133355000Y-112405000D01* +X133355000Y-112595000D01* G37* G36* -X125955000Y-69385000D02* +X133355000Y-112785000D02* G01* -X125765000Y-69385000D01* -X125765000Y-69195000D01* -X125955000Y-69195000D01* -X125955000Y-69385000D01* +X133165000Y-112785000D01* +X133165000Y-112595000D01* +X133355000Y-112595000D01* +X133355000Y-112785000D01* G37* G36* -X125955000Y-69575000D02* +X133355000Y-112975000D02* G01* -X125765000Y-69575000D01* -X125765000Y-69385000D01* -X125955000Y-69385000D01* -X125955000Y-69575000D01* +X133165000Y-112975000D01* +X133165000Y-112785000D01* +X133355000Y-112785000D01* +X133355000Y-112975000D01* G37* G36* -X125955000Y-69765000D02* +X133355000Y-113165000D02* G01* -X125765000Y-69765000D01* -X125765000Y-69575000D01* -X125955000Y-69575000D01* -X125955000Y-69765000D01* +X133165000Y-113165000D01* +X133165000Y-112975000D01* +X133355000Y-112975000D01* +X133355000Y-113165000D01* G37* %TO.C,U_IMU1*% -D10* -X143090000Y-66440000D02* -X143090000Y-66615000D01* -X143090000Y-68985000D02* -X143090000Y-69160000D01* -X143090000Y-69160000D02* -X143765000Y-69160000D01* -X143765000Y-66440000D02* -X143090000Y-66440000D01* -X145635000Y-69160000D02* -X146310000Y-69160000D01* -X146310000Y-66440000D02* -X145635000Y-66440000D01* -X146310000Y-66615000D02* -X146310000Y-66440000D01* -X146310000Y-69160000D02* -X146310000Y-68985000D01* -X146440000Y-67050000D02* -X146770000Y-67290000D01* -X146770000Y-66810000D01* -X146440000Y-67050000D01* -G36* -X146770000Y-67290000D02* -G01* -X146440000Y-67050000D01* -X146770000Y-66810000D01* -X146770000Y-67290000D01* -G37* +D11* +X128452500Y-125652500D02* +X128452500Y-126327500D01* +X128452500Y-128197500D02* +X128452500Y-128872500D01* +X128452500Y-128872500D02* +X128627500Y-128872500D01* +X128627500Y-125652500D02* +X128452500Y-125652500D01* +X130997500Y-128872500D02* +X131172500Y-128872500D01* +X131172500Y-125652500D02* +X130997500Y-125652500D01* +X131172500Y-126327500D02* +X131172500Y-125652500D01* +X131172500Y-128872500D02* +X131172500Y-128197500D01* +X129062500Y-125522500D02* +X129302500Y-125192500D01* +X128822500Y-125192500D01* +X129062500Y-125522500D01* +G36* +X129062500Y-125522500D02* +G01* +X128822500Y-125192500D01* +X129302500Y-125192500D01* +X129062500Y-125522500D01* +G37* +%TO.C,C_BUCK_IN1*% +X145765000Y-90861252D02* +X145765000Y-90338748D01* +X147235000Y-90861252D02* +X147235000Y-90338748D01* %TO.C,C_LATCH_G1*% X135112836Y-74530000D02* X134897164Y-74530000D01* X135112836Y-75250000D02* X134897164Y-75250000D01* %TO.C,C_HALL1*% -X128692164Y-64240000D02* -X128907836Y-64240000D01* -X128692164Y-64960000D02* -X128907836Y-64960000D01* +X129312164Y-63440000D02* +X129527836Y-63440000D01* +X129312164Y-64160000D02* +X129527836Y-64160000D01* %TO.C,R_INV_BASE1*% X125524941Y-88585000D02* X125217659Y-88585000D01* @@ -2160,452 +1963,470 @@ X133955000Y-76577500D01* X134285000Y-76337500D01* X134285000Y-76817500D01* G37* -%TO.C,J_SWD1*% -X145030000Y-113505000D02* -X145030000Y-114140000D01* -X145030000Y-114140000D02* -X145665000Y-114140000D01* +%TO.C,C_SYS_2*% +X130890000Y-94622164D02* +X130890000Y-94837836D01* +X131610000Y-94622164D02* +X131610000Y-94837836D01* %TO.C,C_IMU_2*% -X140240000Y-69109420D02* -X140240000Y-69390580D01* -X141260000Y-69109420D02* -X141260000Y-69390580D01* +X124840580Y-125190000D02* +X124559420Y-125190000D01* +X124840580Y-126210000D02* +X124559420Y-126210000D01* D12* %TO.C,LOGO2*% G36* -X124144700Y-114974600D02* -G01* -X124116600Y-115012500D01* -X124065000Y-115076100D01* -X123995300Y-115158700D01* -X123913100Y-115253700D01* -X123763000Y-115424800D01* -X123742100Y-115448600D01* -X123717800Y-115476400D01* -X123696900Y-115500300D01* -X123678000Y-115521800D01* -X123870100Y-115809900D01* -X123886000Y-115833800D01* -X123901800Y-115857600D01* -X123915100Y-115877400D01* -X123933600Y-115905200D01* -X124069700Y-116109500D01* -X124461400Y-116697100D01* -X125188300Y-116883100D01* -X125915200Y-117069100D01* -X125901400Y-117249500D01* -X125897000Y-117318300D01* -X125891000Y-117428600D01* -X125883900Y-117569900D01* -X125876200Y-117734000D01* -X125868200Y-117912400D01* -X125860400Y-118096800D01* -X125859400Y-118122300D01* -X125852100Y-118293500D01* -X125845200Y-118447600D01* -X125838800Y-118578600D01* -X125833500Y-118680300D01* -X125829300Y-118746600D01* -X125826700Y-118771400D01* -X125820100Y-118770600D01* -X125775400Y-118760900D01* -X125694200Y-118741800D01* -X125582800Y-118714900D01* -X125447600Y-118681800D01* -X125294800Y-118644000D01* -X125130900Y-118603200D01* -X124962100Y-118561000D01* -X124794800Y-118518900D01* -X124635300Y-118478600D01* -X124489900Y-118441500D01* -X124365100Y-118409400D01* -X124267100Y-118383700D01* -X124202300Y-118366200D01* -X124177000Y-118358200D01* -X124176500Y-118352800D01* -X124176800Y-118308900D01* -X124179200Y-118225800D01* -X124183300Y-118109400D01* -X124189000Y-117965300D01* -X124196100Y-117799400D01* -X124204300Y-117617500D01* -X124238500Y-116881900D01* -X124092100Y-116702600D01* -X124081800Y-116690000D01* -X124006600Y-116597800D01* -X123913900Y-116484100D01* -X123814600Y-116362300D01* -X123719400Y-116245400D01* -X123646800Y-116157700D01* -X123565700Y-116064800D01* -X123503000Y-116001700D01* -X123453300Y-115962800D01* -X123411300Y-115943100D01* -X123346200Y-115931700D01* -X123288900Y-115951500D01* -X123242500Y-116013300D01* -X123236400Y-116033600D01* -X123224900Y-116096900D01* -X123219700Y-116133500D01* -X123211100Y-116193000D01* -X123195700Y-116313800D01* -X123179500Y-116451500D01* -X123163500Y-116597900D01* -X123148400Y-116745100D01* -X123135200Y-116885100D01* -X123124500Y-117009800D01* -X123117400Y-117111200D01* -X123114500Y-117181500D01* -X123116800Y-117212400D01* -X123118500Y-117215100D01* -X123142200Y-117248900D01* -X123189500Y-117314800D01* -X123256600Y-117407900D01* -X123339900Y-117523000D01* -X123435800Y-117655100D01* -X123540500Y-117799100D01* -X123565400Y-117833300D01* -X123668400Y-117975000D01* -X123761800Y-118103700D01* -X123841800Y-118214300D01* -X123904700Y-118301600D01* -X123947000Y-118360700D01* -X123959300Y-118378500D01* -X123964800Y-118386400D01* -X123962300Y-118396000D01* -X123933800Y-118438600D01* -X123876500Y-118511500D01* -X123792800Y-118611900D01* -X123685200Y-118736700D01* -X123556100Y-118883100D01* -X123407800Y-119048300D01* -X122834200Y-119682700D01* -X122791800Y-119628200D01* -X122746000Y-119568200D01* -X122678900Y-119478100D01* -X122597300Y-119367100D01* -X122505200Y-119240700D01* -X122406300Y-119104200D01* -X122304500Y-118963000D01* -X122203800Y-118822600D01* -X122108000Y-118688300D01* -X122020900Y-118565500D01* -X121946400Y-118459600D01* -X121888500Y-118376000D01* -X121857624Y-118330300D01* -X122067700Y-118330300D01* -X122078600Y-118346400D01* -X122114900Y-118397800D01* -X122172100Y-118478000D01* -X122246200Y-118581400D01* -X122333300Y-118702400D01* -X122429300Y-118835300D01* -X122498700Y-118931200D01* -X122591300Y-119058100D01* -X122673400Y-119169800D01* -X122740800Y-119260300D01* -X122789000Y-119324000D01* -X122813800Y-119354800D01* -X122823000Y-119363300D01* -X122837600Y-119368800D01* -X122857500Y-119363300D01* -X122886500Y-119343400D01* -X122928300Y-119305600D01* -X122986700Y-119246300D01* -X123065600Y-119162000D01* -X123168600Y-119049200D01* -X123299700Y-118904500D01* -X123401300Y-118791100D01* -X123516300Y-118659700D01* -X123609800Y-118549400D01* -X123679000Y-118463400D01* -X123720900Y-118405400D01* -X123733000Y-118378500D01* -X123727900Y-118368900D01* -X123698700Y-118323700D01* -X123648200Y-118250800D01* -X123581000Y-118156100D01* -X123501400Y-118045700D01* -X123414000Y-117925600D01* -X123323200Y-117801900D01* -X123233400Y-117680700D01* -X123149100Y-117567900D01* -X123074700Y-117469700D01* -X123014700Y-117392000D01* -X122973600Y-117341000D01* -X122955800Y-117322600D01* -X122939500Y-117333200D01* -X122895400Y-117374500D01* -X122829800Y-117442000D01* -X122747600Y-117530000D01* -X122653700Y-117633000D01* -X122552900Y-117745400D01* -X122450200Y-117861700D01* -X122350500Y-117976400D01* -X122258700Y-118083800D01* -X122179500Y-118178500D01* -X122118100Y-118254800D01* -X122079200Y-118307300D01* -X122067700Y-118330300D01* -X121857624Y-118330300D01* -X121850800Y-118320200D01* -X121837400Y-118297400D01* -X121840000Y-118292100D01* -X121867200Y-118256200D01* -X121921100Y-118191500D01* -X121997700Y-118102400D01* -X122093200Y-117993500D01* -X122203600Y-117869200D01* -X122325100Y-117734200D01* -X122812800Y-117195100D01* -X122819400Y-116488800D01* -X122822124Y-116201600D01* -X122984500Y-116201600D01* -X122986100Y-116313000D01* -X122992800Y-116596100D01* -X123020800Y-116322100D01* -X123026400Y-116263700D01* -X123034200Y-116133500D01* -X123031200Y-116048700D01* -X123017200Y-116009700D01* -X122992400Y-116016800D01* -X122987900Y-116043700D01* -X122985200Y-116108600D01* -X122984500Y-116201600D01* -X122822124Y-116201600D01* -X122824936Y-115905200D01* -X123242900Y-115905200D01* -X123254800Y-115917100D01* -X123266800Y-115905200D01* -X123254800Y-115893300D01* -X123242900Y-115905200D01* -X122824936Y-115905200D01* -X122825131Y-115884600D01* -X123151900Y-115884600D01* -X123171500Y-115893300D01* -X123184100Y-115891600D01* -X123187300Y-115877400D01* -X123183900Y-115874600D01* -X123155600Y-115877400D01* -X123151900Y-115884600D01* -X122825131Y-115884600D01* -X122825387Y-115857600D01* -X123076200Y-115857600D01* -X123088100Y-115869500D01* -X123100000Y-115857600D01* -X123088100Y-115845700D01* -X123076200Y-115857600D01* -X122825387Y-115857600D01* -X122825613Y-115833800D01* -X122980900Y-115833800D01* -X122992800Y-115845700D01* -X123004700Y-115833800D01* -X122992800Y-115821900D01* -X122980900Y-115833800D01* -X122825613Y-115833800D01* -X122825840Y-115809900D01* -X122885600Y-115809900D01* -X122897500Y-115821900D01* -X122909400Y-115809900D01* -X122897500Y-115798000D01* -X122885600Y-115809900D01* -X122825840Y-115809900D01* -X122826100Y-115782500D01* -X122474700Y-115691600D01* -X122396500Y-115671400D01* -X122284600Y-115641400D01* -X122208400Y-115618600D01* -X122161100Y-115599800D01* -X122135800Y-115582200D01* -X122125900Y-115562800D01* -X122124400Y-115538600D01* -X122127785Y-115500300D01* -X123576400Y-115500300D01* -X123588300Y-115512200D01* -X123600300Y-115500300D01* -X123588300Y-115488300D01* -X123576400Y-115500300D01* -X122127785Y-115500300D01* -X122127900Y-115499000D01* -X122130502Y-115476400D01* -X123481100Y-115476400D01* -X123493100Y-115488300D01* -X123505000Y-115476400D01* -X123493100Y-115464500D01* -X123481100Y-115476400D01* -X122130502Y-115476400D01* -X122132874Y-115455800D01* -X123366300Y-115455800D01* -X123385900Y-115464500D01* -X123398500Y-115462800D01* -X123401700Y-115448600D01* -X123398300Y-115445800D01* -X123370000Y-115448600D01* -X123366300Y-115455800D01* -X122132874Y-115455800D01* -X122135615Y-115432000D01* -X123271000Y-115432000D01* -X123290600Y-115440700D01* -X123303200Y-115439000D01* -X123306500Y-115424800D01* -X123303000Y-115422000D01* -X123274700Y-115424800D01* -X123271000Y-115432000D01* -X122135615Y-115432000D01* -X122137100Y-115419100D01* -X122151200Y-115305700D01* -X122169300Y-115165700D01* -X122190500Y-115005900D01* -X122214000Y-114833200D01* -X122302500Y-114190100D01* -X121451800Y-112571000D01* -X121427500Y-112524700D01* -X121263800Y-112212800D01* -X121121300Y-111940500D01* -X120999000Y-111705800D01* -X120895800Y-111506600D01* -X120810600Y-111340900D01* -X120742500Y-111206400D01* -X120690200Y-111101200D01* -X120652900Y-111023100D01* -X120629500Y-110970100D01* -X120618800Y-110940000D01* -X120619900Y-110930800D01* -X120631600Y-110940400D01* -X120634800Y-110944900D01* -X120660100Y-110982400D01* -X120709000Y-111055300D01* -X120779300Y-111160500D01* -X120869200Y-111295200D01* -X120976700Y-111456400D01* -X121099700Y-111641000D01* -X121236300Y-111846200D01* -X121384500Y-112068800D01* -X121542400Y-112306000D01* -X121707900Y-112554700D01* -X122775000Y-114159200D01* -X122695800Y-114686800D01* -X122684700Y-114760400D01* -X122662100Y-114907900D01* -X122642000Y-115036600D01* -X122625400Y-115139500D01* -X122613500Y-115209500D01* -X122607400Y-115239400D01* -X122623600Y-115253800D01* -X122679400Y-115276100D01* -X122768000Y-115303100D01* -X122882100Y-115332700D01* -X123165800Y-115400800D01* -X123313000Y-115243500D01* -X123338500Y-115216100D01* -X123409900Y-115137900D01* -X123470500Y-115069700D01* -X123509300Y-115023800D01* -X123516000Y-115015200D01* -X123543400Y-114974800D01* -X123541600Y-114946800D01* -X123511000Y-114909300D01* -X123508600Y-114906600D01* -X123474300Y-114868900D01* -X123414400Y-114803200D01* -X123334700Y-114715800D01* -X123241000Y-114613000D01* -X123138900Y-114501200D01* -X122814100Y-114145300D01* -X122814165Y-114070900D01* -X122982700Y-114070900D01* -X123362900Y-114483900D01* -X123382400Y-114505000D01* -X123509500Y-114643700D01* -X123606600Y-114753500D01* -X123676000Y-114839600D01* -X123719500Y-114907700D01* -X123739400Y-114963100D01* -X123737700Y-115011100D01* -X123716400Y-115057200D01* -X123677500Y-115106800D01* -X123623300Y-115165300D01* -X123577600Y-115215000D01* -X123538500Y-115264100D01* -X123527900Y-115292500D01* -X123541900Y-115306800D01* -X123562400Y-115313900D01* -X123598700Y-115321600D01* -X123602000Y-115320600D01* -X123631800Y-115296300D01* -X123680700Y-115247100D01* -X123740100Y-115182700D01* -X123801400Y-115112800D01* -X123855900Y-115047400D01* -X123895000Y-114996200D01* -X123909900Y-114969100D01* -X123900200Y-114952900D01* -X123862700Y-114904700D01* -X123801200Y-114830100D01* -X123719900Y-114734100D01* -X123622900Y-114621800D01* -X123514700Y-114498400D01* -X123431000Y-114403300D01* -X123327200Y-114284500D01* -X123236100Y-114179300D01* -X123162500Y-114093300D01* -X123111100Y-114031900D01* -X123086700Y-114000700D01* -X123085100Y-113998000D01* -X123069900Y-113951200D01* -X123052600Y-113868900D01* -X123035500Y-113762100D01* -X123020300Y-113641500D01* -X122986800Y-113332500D01* -X122984700Y-113701700D01* -X122982700Y-114070900D01* -X122814165Y-114070900D01* -X122815800Y-112202400D01* -X122815800Y-112119000D01* -X122816500Y-111807300D01* -X122817500Y-111516700D01* -X122819000Y-111250200D01* -X122820900Y-111010800D01* -X122823100Y-110801400D01* -X122825600Y-110624900D01* -X122828300Y-110484300D01* -X122831400Y-110382500D01* -X122834600Y-110322400D01* -X122838000Y-110307100D01* -X122838000Y-110307200D01* -X122843800Y-110338800D01* -X122853900Y-110413900D01* -X122867900Y-110528700D01* -X122885400Y-110679500D01* -X122906000Y-110862500D01* -X122929200Y-111073700D01* -X122954700Y-111309500D01* -X122982000Y-111566000D01* -X123010600Y-111839500D01* -X123040200Y-112126000D01* -X123221900Y-113897300D01* -X123685000Y-114423400D01* -X123719800Y-114462900D01* -X123834400Y-114594000D01* -X123936900Y-114712400D01* -X124023500Y-114813600D01* -X124090100Y-114892800D01* -X124133000Y-114945700D01* -X124148200Y-114967500D01* -X124147400Y-114969100D01* -X124144700Y-114974600D01* -G37* +X147244700Y-108174600D02* +G01* +X147216600Y-108212500D01* +X147165000Y-108276100D01* +X147095300Y-108358700D01* +X147013100Y-108453700D01* +X146863000Y-108624800D01* +X146842100Y-108648600D01* +X146817800Y-108676400D01* +X146796900Y-108700300D01* +X146778000Y-108721800D01* +X146970100Y-109009900D01* +X146986000Y-109033800D01* +X147001800Y-109057600D01* +X147015100Y-109077400D01* +X147033600Y-109105200D01* +X147169700Y-109309500D01* +X147561400Y-109897100D01* +X148288300Y-110083100D01* +X149015200Y-110269100D01* +X149001400Y-110449500D01* +X148997000Y-110518300D01* +X148991000Y-110628600D01* +X148983900Y-110769900D01* +X148976200Y-110934000D01* +X148968200Y-111112400D01* +X148960400Y-111296800D01* +X148959400Y-111322300D01* +X148952100Y-111493500D01* +X148945200Y-111647600D01* +X148938800Y-111778600D01* +X148933500Y-111880300D01* +X148929300Y-111946600D01* +X148926700Y-111971400D01* +X148920100Y-111970600D01* +X148875400Y-111960900D01* +X148794200Y-111941800D01* +X148682800Y-111914900D01* +X148547600Y-111881800D01* +X148394800Y-111844000D01* +X148230900Y-111803200D01* +X148062100Y-111761000D01* +X147894800Y-111718900D01* +X147735300Y-111678600D01* +X147589900Y-111641500D01* +X147465100Y-111609400D01* +X147367100Y-111583700D01* +X147302300Y-111566200D01* +X147277000Y-111558200D01* +X147276500Y-111552800D01* +X147276800Y-111508900D01* +X147279200Y-111425800D01* +X147283300Y-111309400D01* +X147289000Y-111165300D01* +X147296100Y-110999400D01* +X147304300Y-110817500D01* +X147338500Y-110081900D01* +X147192100Y-109902600D01* +X147181800Y-109890000D01* +X147106600Y-109797800D01* +X147013900Y-109684100D01* +X146914600Y-109562300D01* +X146819400Y-109445400D01* +X146746800Y-109357700D01* +X146665700Y-109264800D01* +X146603000Y-109201700D01* +X146553300Y-109162800D01* +X146511300Y-109143100D01* +X146446200Y-109131700D01* +X146388900Y-109151500D01* +X146342500Y-109213300D01* +X146336400Y-109233600D01* +X146324900Y-109296900D01* +X146319700Y-109333500D01* +X146311100Y-109393000D01* +X146295700Y-109513800D01* +X146279500Y-109651500D01* +X146263500Y-109797900D01* +X146248400Y-109945100D01* +X146235200Y-110085100D01* +X146224500Y-110209800D01* +X146217400Y-110311200D01* +X146214500Y-110381500D01* +X146216800Y-110412400D01* +X146218500Y-110415100D01* +X146242200Y-110448900D01* +X146289500Y-110514800D01* +X146356600Y-110607900D01* +X146439900Y-110723000D01* +X146535800Y-110855100D01* +X146640500Y-110999100D01* +X146665400Y-111033300D01* +X146768400Y-111175000D01* +X146861800Y-111303700D01* +X146941800Y-111414300D01* +X147004700Y-111501600D01* +X147047000Y-111560700D01* +X147059300Y-111578500D01* +X147064800Y-111586400D01* +X147062300Y-111596000D01* +X147033800Y-111638600D01* +X146976500Y-111711500D01* +X146892800Y-111811900D01* +X146785200Y-111936700D01* +X146656100Y-112083100D01* +X146507800Y-112248300D01* +X145934200Y-112882700D01* +X145891800Y-112828200D01* +X145846000Y-112768200D01* +X145778900Y-112678100D01* +X145697300Y-112567100D01* +X145605200Y-112440700D01* +X145506300Y-112304200D01* +X145404500Y-112163000D01* +X145303800Y-112022600D01* +X145208000Y-111888300D01* +X145120900Y-111765500D01* +X145046400Y-111659600D01* +X144988500Y-111576000D01* +X144957624Y-111530300D01* +X145167700Y-111530300D01* +X145178600Y-111546400D01* +X145214900Y-111597800D01* +X145272100Y-111678000D01* +X145346200Y-111781400D01* +X145433300Y-111902400D01* +X145529300Y-112035300D01* +X145598700Y-112131200D01* +X145691300Y-112258100D01* +X145773400Y-112369800D01* +X145840800Y-112460300D01* +X145889000Y-112524000D01* +X145913800Y-112554800D01* +X145923000Y-112563300D01* +X145937600Y-112568800D01* +X145957500Y-112563300D01* +X145986500Y-112543400D01* +X146028300Y-112505600D01* +X146086700Y-112446300D01* +X146165600Y-112362000D01* +X146268600Y-112249200D01* +X146399700Y-112104500D01* +X146501300Y-111991100D01* +X146616300Y-111859700D01* +X146709800Y-111749400D01* +X146779000Y-111663400D01* +X146820900Y-111605400D01* +X146833000Y-111578500D01* +X146827900Y-111568900D01* +X146798700Y-111523700D01* +X146748200Y-111450800D01* +X146681000Y-111356100D01* +X146601400Y-111245700D01* +X146514000Y-111125600D01* +X146423200Y-111001900D01* +X146333400Y-110880700D01* +X146249100Y-110767900D01* +X146174700Y-110669700D01* +X146114700Y-110592000D01* +X146073600Y-110541000D01* +X146055800Y-110522600D01* +X146039500Y-110533200D01* +X145995400Y-110574500D01* +X145929800Y-110642000D01* +X145847600Y-110730000D01* +X145753700Y-110833000D01* +X145652900Y-110945400D01* +X145550200Y-111061700D01* +X145450500Y-111176400D01* +X145358700Y-111283800D01* +X145279500Y-111378500D01* +X145218100Y-111454800D01* +X145179200Y-111507300D01* +X145167700Y-111530300D01* +X144957624Y-111530300D01* +X144950800Y-111520200D01* +X144937400Y-111497400D01* +X144940000Y-111492100D01* +X144967200Y-111456200D01* +X145021100Y-111391500D01* +X145097700Y-111302400D01* +X145193200Y-111193500D01* +X145303600Y-111069200D01* +X145425100Y-110934200D01* +X145912800Y-110395100D01* +X145919400Y-109688800D01* +X145922124Y-109401600D01* +X146084500Y-109401600D01* +X146086100Y-109513000D01* +X146092800Y-109796100D01* +X146120800Y-109522100D01* +X146126400Y-109463700D01* +X146134200Y-109333500D01* +X146131200Y-109248700D01* +X146117200Y-109209700D01* +X146092400Y-109216800D01* +X146087900Y-109243700D01* +X146085200Y-109308600D01* +X146084500Y-109401600D01* +X145922124Y-109401600D01* +X145924936Y-109105200D01* +X146342900Y-109105200D01* +X146354800Y-109117100D01* +X146366800Y-109105200D01* +X146354800Y-109093300D01* +X146342900Y-109105200D01* +X145924936Y-109105200D01* +X145925131Y-109084600D01* +X146251900Y-109084600D01* +X146271500Y-109093300D01* +X146284100Y-109091600D01* +X146287300Y-109077400D01* +X146283900Y-109074600D01* +X146255600Y-109077400D01* +X146251900Y-109084600D01* +X145925131Y-109084600D01* +X145925387Y-109057600D01* +X146176200Y-109057600D01* +X146188100Y-109069500D01* +X146200000Y-109057600D01* +X146188100Y-109045700D01* +X146176200Y-109057600D01* +X145925387Y-109057600D01* +X145925613Y-109033800D01* +X146080900Y-109033800D01* +X146092800Y-109045700D01* +X146104700Y-109033800D01* +X146092800Y-109021900D01* +X146080900Y-109033800D01* +X145925613Y-109033800D01* +X145925840Y-109009900D01* +X145985600Y-109009900D01* +X145997500Y-109021900D01* +X146009400Y-109009900D01* +X145997500Y-108998000D01* +X145985600Y-109009900D01* +X145925840Y-109009900D01* +X145926100Y-108982500D01* +X145574700Y-108891600D01* +X145496500Y-108871400D01* +X145384600Y-108841400D01* +X145308400Y-108818600D01* +X145261100Y-108799800D01* +X145235800Y-108782200D01* +X145225900Y-108762800D01* +X145224400Y-108738600D01* +X145227785Y-108700300D01* +X146676400Y-108700300D01* +X146688300Y-108712200D01* +X146700300Y-108700300D01* +X146688300Y-108688300D01* +X146676400Y-108700300D01* +X145227785Y-108700300D01* +X145227900Y-108699000D01* +X145230502Y-108676400D01* +X146581100Y-108676400D01* +X146593100Y-108688300D01* +X146605000Y-108676400D01* +X146593100Y-108664500D01* +X146581100Y-108676400D01* +X145230502Y-108676400D01* +X145232874Y-108655800D01* +X146466300Y-108655800D01* +X146485900Y-108664500D01* +X146498500Y-108662800D01* +X146501700Y-108648600D01* +X146498300Y-108645800D01* +X146470000Y-108648600D01* +X146466300Y-108655800D01* +X145232874Y-108655800D01* +X145235615Y-108632000D01* +X146371000Y-108632000D01* +X146390600Y-108640700D01* +X146403200Y-108639000D01* +X146406500Y-108624800D01* +X146403000Y-108622000D01* +X146374700Y-108624800D01* +X146371000Y-108632000D01* +X145235615Y-108632000D01* +X145237100Y-108619100D01* +X145251200Y-108505700D01* +X145269300Y-108365700D01* +X145290500Y-108205900D01* +X145314000Y-108033200D01* +X145402500Y-107390100D01* +X144551800Y-105771000D01* +X144527500Y-105724700D01* +X144363800Y-105412800D01* +X144221300Y-105140500D01* +X144099000Y-104905800D01* +X143995800Y-104706600D01* +X143910600Y-104540900D01* +X143842500Y-104406400D01* +X143790200Y-104301200D01* +X143752900Y-104223100D01* +X143729500Y-104170100D01* +X143718800Y-104140000D01* +X143719900Y-104130800D01* +X143731600Y-104140400D01* +X143734800Y-104144900D01* +X143760100Y-104182400D01* +X143809000Y-104255300D01* +X143879300Y-104360500D01* +X143969200Y-104495200D01* +X144076700Y-104656400D01* +X144199700Y-104841000D01* +X144336300Y-105046200D01* +X144484500Y-105268800D01* +X144642400Y-105506000D01* +X144807900Y-105754700D01* +X145875000Y-107359200D01* +X145795800Y-107886800D01* +X145784700Y-107960400D01* +X145762100Y-108107900D01* +X145742000Y-108236600D01* +X145725400Y-108339500D01* +X145713500Y-108409500D01* +X145707400Y-108439400D01* +X145723600Y-108453800D01* +X145779400Y-108476100D01* +X145868000Y-108503100D01* +X145982100Y-108532700D01* +X146265800Y-108600800D01* +X146413000Y-108443500D01* +X146438500Y-108416100D01* +X146509900Y-108337900D01* +X146570500Y-108269700D01* +X146609300Y-108223800D01* +X146616000Y-108215200D01* +X146643400Y-108174800D01* +X146641600Y-108146800D01* +X146611000Y-108109300D01* +X146608600Y-108106600D01* +X146574300Y-108068900D01* +X146514400Y-108003200D01* +X146434700Y-107915800D01* +X146341000Y-107813000D01* +X146238900Y-107701200D01* +X145914100Y-107345300D01* +X145914165Y-107270900D01* +X146082700Y-107270900D01* +X146462900Y-107683900D01* +X146482400Y-107705000D01* +X146609500Y-107843700D01* +X146706600Y-107953500D01* +X146776000Y-108039600D01* +X146819500Y-108107700D01* +X146839400Y-108163100D01* +X146837700Y-108211100D01* +X146816400Y-108257200D01* +X146777500Y-108306800D01* +X146723300Y-108365300D01* +X146677600Y-108415000D01* +X146638500Y-108464100D01* +X146627900Y-108492500D01* +X146641900Y-108506800D01* +X146662400Y-108513900D01* +X146698700Y-108521600D01* +X146702000Y-108520600D01* +X146731800Y-108496300D01* +X146780700Y-108447100D01* +X146840100Y-108382700D01* +X146901400Y-108312800D01* +X146955900Y-108247400D01* +X146995000Y-108196200D01* +X147009900Y-108169100D01* +X147000200Y-108152900D01* +X146962700Y-108104700D01* +X146901200Y-108030100D01* +X146819900Y-107934100D01* +X146722900Y-107821800D01* +X146614700Y-107698400D01* +X146531000Y-107603300D01* +X146427200Y-107484500D01* +X146336100Y-107379300D01* +X146262500Y-107293300D01* +X146211100Y-107231900D01* +X146186700Y-107200700D01* +X146185100Y-107198000D01* +X146169900Y-107151200D01* +X146152600Y-107068900D01* +X146135500Y-106962100D01* +X146120300Y-106841500D01* +X146086800Y-106532500D01* +X146084700Y-106901700D01* +X146082700Y-107270900D01* +X145914165Y-107270900D01* +X145915800Y-105402400D01* +X145915800Y-105319000D01* +X145916500Y-105007300D01* +X145917500Y-104716700D01* +X145919000Y-104450200D01* +X145920900Y-104210800D01* +X145923100Y-104001400D01* +X145925600Y-103824900D01* +X145928300Y-103684300D01* +X145931400Y-103582500D01* +X145934600Y-103522400D01* +X145938000Y-103507100D01* +X145938000Y-103507200D01* +X145943800Y-103538800D01* +X145953900Y-103613900D01* +X145967900Y-103728700D01* +X145985400Y-103879500D01* +X146006000Y-104062500D01* +X146029200Y-104273700D01* +X146054700Y-104509500D01* +X146082000Y-104766000D01* +X146110600Y-105039500D01* +X146140200Y-105326000D01* +X146321900Y-107097300D01* +X146785000Y-107623400D01* +X146819800Y-107662900D01* +X146934400Y-107794000D01* +X147036900Y-107912400D01* +X147123500Y-108013600D01* +X147190100Y-108092800D01* +X147233000Y-108145700D01* +X147248200Y-108167500D01* +X147247400Y-108169100D01* +X147244700Y-108174600D01* +G37* +%TO.C,C_BAT1*% +D11* +X132938748Y-97015000D02* +X133461252Y-97015000D01* +X132938748Y-98485000D02* +X133461252Y-98485000D01* +%TO.C,U_CHG1*% +D13* +X130800000Y-95450000D02* +G75* +G02* +X130600000Y-95450000I-100000J0D01* +G01* +X130600000Y-95450000D02* +G75* +G02* +X130800000Y-95450000I100000J0D01* +G01* +%TO.C,R_STAT2*% +D11* +X133196359Y-99670000D02* +X133503641Y-99670000D01* +X133196359Y-100430000D02* +X133503641Y-100430000D01* %TO.C,R_CC2*% -D10* X141621359Y-125685000D02* X141928641Y-125685000D01* X141621359Y-126445000D02* X141928641Y-126445000D01* -%TO.C,C_OLED_2*% -X123587836Y-104840000D02* -X123372164Y-104840000D01* -X123587836Y-105560000D02* -X123372164Y-105560000D01* %TO.C,D_OR2*% X132925000Y-71440000D02* X136935000Y-71440000D01* @@ -2613,129 +2434,706 @@ X132925000Y-73440000D02* X132925000Y-71440000D01* X132925000Y-73440000D02* X136935000Y-73440000D01* +D12* +%TO.C,LOGO3*% +G36* +X137449257Y-108523111D02* +G01* +X137613301Y-108553744D01* +X137758505Y-108625310D01* +X137890051Y-108740104D01* +X137907636Y-108759605D01* +X138010454Y-108899175D01* +X138079560Y-109050209D01* +X138118254Y-109222124D01* +X138129836Y-109424338D01* +X138128770Y-109485353D01* +X138120542Y-109603836D01* +X138102220Y-109719772D01* +X138071420Y-109841818D01* +X138025761Y-109978633D01* +X137962861Y-110138876D01* +X137880337Y-110331205D01* +X137827803Y-110451253D01* +X137770821Y-110583414D01* +X137720584Y-110701941D01* +X137681133Y-110797283D01* +X137656513Y-110859890D01* +X137635055Y-110915158D01* +X137606910Y-110979497D01* +X137586702Y-111016180D01* +X137578690Y-111024811D01* +X137529322Y-111043568D01* +X137468291Y-111030347D01* +X137404801Y-110992035D01* +X137348055Y-110935516D01* +X137307258Y-110867678D01* +X137291614Y-110795407D01* +X137294893Y-110774206D01* +X137316422Y-110704626D01* +X137357851Y-110594303D01* +X137418952Y-110443810D01* +X137499497Y-110253719D01* +X137599256Y-110024604D01* +X137616906Y-109984306D01* +X137683891Y-109826124D01* +X137732920Y-109697842D01* +X137766562Y-109590203D01* +X137787387Y-109493950D01* +X137797968Y-109399827D01* +X137800874Y-109298577D01* +X137798544Y-109198941D01* +X137783550Y-109067509D01* +X137752132Y-108973427D01* +X137701366Y-108912053D01* +X137628328Y-108878746D01* +X137530093Y-108868867D01* +X137418925Y-108885032D01* +X137287029Y-108940592D01* +X137160572Y-109029361D01* +X137047139Y-109144707D01* +X136954316Y-109280001D01* +X136889689Y-109428612D01* +X136880401Y-109450231D01* +X136837450Y-109488515D01* +X136777423Y-109495166D01* +X136710037Y-109472727D01* +X136645012Y-109423740D01* +X136592065Y-109350748D01* +X136580790Y-109328414D01* +X136563379Y-109280451D01* +X136565322Y-109234584D01* +X136585855Y-109168396D01* +X136643128Y-109035073D01* +X136737765Y-108889899D01* +X136868222Y-108752270D01* +X136996213Y-108647478D01* +X137122751Y-108574387D01* +X137252607Y-108534052D01* +X137397049Y-108521556D01* +X137449257Y-108523111D01* +G37* +G36* +X136859219Y-109850093D02* +G01* +X136935642Y-109918261D01* +X136960391Y-109949033D01* +X136977590Y-109979019D01* +X136987145Y-110016284D01* +X136990376Y-110070569D01* +X136988601Y-110151617D01* +X136983139Y-110269171D01* +X136971792Y-110425290D01* +X136917352Y-110773640D01* +X136822337Y-111105334D01* +X136685001Y-111427164D01* +X136646762Y-111501417D01* +X136586740Y-111605869D01* +X136521221Y-111702241D01* +X136444072Y-111797932D01* +X136349155Y-111900340D01* +X136230337Y-112016864D01* +X136081480Y-112154902D01* +X136055246Y-112178911D01* +X135886259Y-112339334D01* +X135752846Y-112477850D01* +X135652309Y-112597634D01* +X135581953Y-112701863D01* +X135539080Y-112793712D01* +X135511523Y-112873288D01* +X135656410Y-112918039D01* +X135743730Y-112942260D01* +X135923484Y-112977961D01* +X136107276Y-112998353D01* +X136283385Y-113002870D01* +X136440091Y-112990945D01* +X136565675Y-112962011D01* +X136636350Y-112952312D01* +X136722233Y-112972761D01* +X136798812Y-113020220D01* +X136853783Y-113086648D01* +X136874841Y-113164006D01* +X136874496Y-113173770D01* +X136856824Y-113223831D01* +X136807280Y-113265751D01* +X136718770Y-113305986D01* +X136662962Y-113320863D01* +X136587449Y-113329001D01* +X136483487Y-113330877D01* +X136342298Y-113326979D01* +X136243270Y-113321608D01* +X135988808Y-113293922D01* +X135764475Y-113248349D01* +X135572449Y-113186118D01* +X135414905Y-113108454D01* +X135294020Y-113016585D01* +X135211971Y-112911736D01* +X135170934Y-112795135D01* +X135173086Y-112668008D01* +X135175083Y-112657738D01* +X135201645Y-112566227D01* +X135246258Y-112471680D01* +X135312139Y-112370043D01* +X135402507Y-112257261D01* +X135520579Y-112129278D01* +X135669572Y-111982039D01* +X135852705Y-111811489D01* +X135880190Y-111786282D01* +X136033344Y-111638159D01* +X136155583Y-111502052D01* +X136254073Y-111367066D01* +X136335981Y-111222306D01* +X136408473Y-111056879D01* +X136478718Y-110859890D01* +X136543719Y-110647424D01* +X136589296Y-110457650D01* +X136618942Y-110273143D01* +X136636172Y-110076426D01* +X136643043Y-109971972D01* +X136650796Y-109899146D01* +X136661221Y-109855303D01* +X136676473Y-109831582D01* +X136698705Y-109819124D01* +X136701637Y-109818084D01* +X136777469Y-109815132D01* +X136859219Y-109850093D01* +G37* +G36* +X139340655Y-110475755D02* +G01* +X139406515Y-110505587D01* +X139470097Y-110562318D01* +X139515452Y-110632198D01* +X139535144Y-110703384D01* +X139521731Y-110764033D01* +X139508634Y-110777005D01* +X139457631Y-110804718D01* +X139387978Y-110828277D01* +X139380377Y-110830221D01* +X139307158Y-110851612D01* +X139264116Y-110876498D01* +X139237361Y-110917499D01* +X139213000Y-110987237D01* +X139187984Y-111054403D01* +X139149425Y-111143970D01* +X139106009Y-111235565D01* +X139101785Y-111244083D01* +X139064535Y-111325567D01* +X139038172Y-111394502D01* +X139028168Y-111436742D01* +X139028815Y-111441159D01* +X139053416Y-111480886D01* +X139112125Y-111546436D01* +X139202867Y-111635637D01* +X139323571Y-111746314D01* +X139373296Y-111790951D01* +X139527255Y-111932379D01* +X139650525Y-112052010D01* +X139747734Y-112154950D01* +X139823507Y-112246303D01* +X139882469Y-112331173D01* +X139929246Y-112414664D01* +X139957390Y-112477296D01* +X139996902Y-112624255D01* +X139994557Y-112757816D01* +X139951296Y-112874747D01* +X139868056Y-112971817D01* +X139745779Y-113045795D01* +X139711766Y-113057363D01* +X139607307Y-113074140D01* +X139467778Y-113078838D01* +X139299826Y-113071394D01* +X139110099Y-113051746D01* +X139016839Y-113038875D01* +X138949851Y-113025727D01* +X138907175Y-113008935D01* +X138877524Y-112983925D01* +X138849616Y-112946119D01* +X138814817Y-112873897D01* +X138798047Y-112790780D01* +X138803147Y-112716348D01* +X138831140Y-112666088D01* +X138848075Y-112656934D01* +X138885742Y-112650176D01* +X138947558Y-112649429D01* +X139040779Y-112654689D01* +X139172662Y-112665953D01* +X139335137Y-112677892D01* +X139474572Y-112679559D01* +X139578563Y-112668771D01* +X139652043Y-112644983D01* +X139699945Y-112607649D01* +X139709022Y-112583315D01* +X139692613Y-112525322D01* +X139638648Y-112446068D01* +X139548385Y-112347266D01* +X139423082Y-112230631D01* +X139393402Y-112204564D01* +X139285773Y-112109832D01* +X139170431Y-112008077D01* +X139067729Y-111917248D01* +X139031203Y-111884982D01* +X138959462Y-111823868D01* +X138905951Y-111785388D01* +X138859176Y-111763524D01* +X138807644Y-111752259D01* +X138739862Y-111745574D01* +X138633580Y-111744092D01* +X138456949Y-111767731D01* +X138287006Y-111819459D01* +X138141464Y-111894855D01* +X138105084Y-111918744D01* +X138047220Y-111950769D01* +X138006471Y-111959856D01* +X137969901Y-111950176D01* +X137953769Y-111940689D01* +X137903332Y-111886570D01* +X137860767Y-111809874D01* +X137834557Y-111728569D01* +X137833184Y-111660621D01* +X137844952Y-111632011D01* +X137901034Y-111568720D01* +X137992385Y-111507828D01* +X138111446Y-111452543D01* +X138250657Y-111406074D01* +X138402461Y-111371630D01* +X138559298Y-111352418D01* +X138750319Y-111339597D01* +X138750319Y-111272655D01* +X138750371Y-111268799D01* +X138760803Y-111199065D01* +X138783869Y-111125418D01* +X138789976Y-111110493D01* +X138806913Y-111063897D01* +X138810009Y-111045122D01* +X138800479Y-111048643D01* +X138755292Y-111067675D01* +X138679669Y-111100424D01* +X138580918Y-111143713D01* +X138466350Y-111194368D01* +X138434940Y-111208198D01* +X138288679Y-111270315D01* +X138135012Y-111332521D01* +X137990402Y-111388268D01* +X137871309Y-111431009D01* +X137612517Y-111518404D01* +X137527316Y-111472784D01* +X137505680Y-111459601D01* +X137444387Y-111404159D01* +X137397673Y-111336746D01* +X137373170Y-111270422D01* +X137378512Y-111218241D01* +X137406856Y-111197228D01* +X137470202Y-111166327D01* +X137558973Y-111129938D01* +X137663708Y-111092239D01* +X137751013Y-111061514D01* +X137902436Y-111004311D01* +X138057857Y-110941846D01* +X138194622Y-110883047D01* +X138386670Y-110797619D01* +X138641504Y-110688453D01* +X138857150Y-110601800D01* +X139034248Y-110537431D01* +X139173439Y-110495119D01* +X139275361Y-110474636D01* +X139340655Y-110475755D01* +G37* +G36* +X138202520Y-108183397D02* +G01* +X138226310Y-108245238D01* +X138238301Y-108275777D01* +X138235789Y-108285338D01* +X138206646Y-108281588D01* +X138193676Y-108278103D01* +X138126270Y-108274941D01* +X138023556Y-108282455D01* +X137892580Y-108299332D01* +X137740393Y-108324258D01* +X137574040Y-108355919D01* +X137400572Y-108393002D01* +X137227035Y-108434194D01* +X137060478Y-108478180D01* +X136907949Y-108523646D01* +X136785103Y-108565057D01* +X136746679Y-108579215D01* +X136683841Y-108602369D01* +X136621003Y-108625523D01* +X136586360Y-108638288D01* +X136560107Y-108648677D01* +X136372243Y-108723020D01* +X136157647Y-108813124D01* +X135957467Y-108902473D01* +X135786600Y-108984940D01* +X135746393Y-109005267D01* +X135611526Y-109070650D01* +X135515612Y-109111836D01* +X135458313Y-109128959D01* +X135439289Y-109122154D01* +X135438825Y-109116883D01* +X135417875Y-109100861D01* +X135373570Y-109111590D01* +X135316683Y-109146897D01* +X135315146Y-109148097D01* +X135269301Y-109174416D01* +X135243108Y-109170660D01* +X135245954Y-109156440D01* +X135278965Y-109119251D01* +X135340026Y-109067667D01* +X135421917Y-109006952D01* +X135517420Y-108942367D01* +X135619319Y-108879177D01* +X135720393Y-108822643D01* +X135750966Y-108806203D01* +X135828384Y-108760355D01* +X135885350Y-108720439D01* +X135911269Y-108693617D01* +X135913769Y-108686474D01* +X135910152Y-108667112D01* +X135873282Y-108673016D01* +X135858673Y-108677883D01* +X135786858Y-108706873D01* +X135688927Y-108751008D01* +X135576052Y-108804777D01* +X135459402Y-108862668D01* +X135350149Y-108919169D01* +X135259461Y-108968769D01* +X135198510Y-109005957D01* +X135152658Y-109035278D01* +X135108890Y-109057144D01* +X135091979Y-109056536D01* +X135094201Y-109048283D01* +X135124958Y-109010551D01* +X135186063Y-108957538D01* +X135270080Y-108894905D01* +X135369570Y-108828313D01* +X135477097Y-108763422D01* +X135518932Y-108739303D01* +X135586728Y-108698716D01* +X135629907Y-108670702D01* +X135640557Y-108660254D01* +X135627531Y-108662857D01* +X135574939Y-108684652D01* +X135496072Y-108724692D01* +X135399561Y-108778265D01* +X135294039Y-108840660D01* +X135188139Y-108907166D01* +X135130253Y-108943640D01* +X135062652Y-108982707D01* +X135018330Y-109003716D01* +X135004832Y-109002732D01* +X135016273Y-108985110D01* +X135065154Y-108941329D01* +X135144409Y-108885064D01* +X135246663Y-108820851D01* +X135364538Y-108753225D01* +X135490658Y-108686724D01* +X135570071Y-108648677D01* +X135670830Y-108648677D01* +X135682407Y-108660254D01* +X135693984Y-108648677D01* +X135682407Y-108637100D01* +X135670830Y-108648677D01* +X135570071Y-108648677D01* +X135617647Y-108625883D01* +X135618443Y-108625523D01* +X135717138Y-108625523D01* +X135728715Y-108637100D01* +X135740292Y-108625523D01* +X135728715Y-108613946D01* +X135717138Y-108625523D01* +X135618443Y-108625523D01* +X135669655Y-108602369D01* +X135763446Y-108602369D01* +X135775023Y-108613946D01* +X135786600Y-108602369D01* +X135775023Y-108590792D01* +X135763446Y-108602369D01* +X135669655Y-108602369D01* +X135720868Y-108579215D01* +X135809754Y-108579215D01* +X135821331Y-108590792D01* +X135832908Y-108579215D01* +X135821331Y-108567638D01* +X135809754Y-108579215D01* +X135720868Y-108579215D01* +X135890793Y-108502389D01* +X135905556Y-108296527D01* +X135928412Y-108082190D01* +X135972365Y-107867796D01* +X136036974Y-107685929D01* +X136124347Y-107530856D01* +X136236594Y-107396848D01* +X136317164Y-107324750D01* +X136496380Y-107210254D01* +X136706837Y-107128624D01* +X136949225Y-107079626D01* +X137224236Y-107063027D01* +X137394865Y-107069828D01* +X137658835Y-107112589D01* +X137899206Y-107194896D01* +X138116776Y-107317055D01* +X138312347Y-107479372D01* +X138320017Y-107486977D01* +X138381844Y-107551464D01* +X138438153Y-107617851D01* +X138493250Y-107692756D01* +X138551441Y-107782798D01* +X138617032Y-107894596D01* +X138694330Y-108034769D01* +X138787640Y-108209935D01* +X138812603Y-108257241D01* +X138864794Y-108354657D01* +X138902521Y-108419687D01* +X138930929Y-108458533D01* +X138955164Y-108477397D01* +X138980372Y-108482481D01* +X139011699Y-108479988D01* +X139067003Y-108480452D01* +X139118600Y-108507121D01* +X139136512Y-108535944D01* +X139171459Y-108600519D01* +X139219591Y-108693626D01* +X139277816Y-108808912D01* +X139343041Y-108940022D01* +X139412176Y-109080604D01* +X139482127Y-109224301D01* +X139549803Y-109364762D01* +X139612113Y-109495632D01* +X139665964Y-109610557D01* +X139708264Y-109703183D01* +X139735922Y-109767156D01* +X139745845Y-109796122D01* +X139732284Y-109825032D01* +X139690276Y-109854007D01* +X139634608Y-109875842D01* +X139808365Y-110232011D01* +X139812895Y-110241301D01* +X139875774Y-110371849D01* +X139919950Y-110468206D01* +X139947800Y-110536935D01* +X139961698Y-110584601D01* +X139964021Y-110617767D01* +X139957145Y-110642995D01* +X139942597Y-110666507D01* +X139892349Y-110695325D01* +X139825843Y-110686521D01* +X139750486Y-110640195D01* +X139742420Y-110632143D01* +X139711241Y-110589313D01* +X139665900Y-110514607D01* +X139605495Y-110406342D01* +X139529125Y-110262836D01* +X139435889Y-110082407D01* +X139324884Y-109863373D01* +X139195211Y-109604051D01* +X139088853Y-109390526D01* +X138936294Y-109085517D01* +X138801462Y-108817949D01* +X138682890Y-108585210D01* +X138579110Y-108384687D01* +X138488655Y-108213769D01* +X138410057Y-108069843D01* +X138341848Y-107950296D01* +X138282561Y-107852516D01* +X138230729Y-107773890D01* +X138184882Y-107711807D01* +X138143554Y-107663653D01* +X138105277Y-107626817D01* +X138068584Y-107598686D01* +X138017029Y-107567752D01* +X137932213Y-107523836D01* +X137842565Y-107482918D01* +X137790454Y-107461904D01* +X137734047Y-107443564D01* +X137674970Y-107431780D01* +X137602318Y-107425128D01* +X137505182Y-107422181D01* +X137372653Y-107421515D01* +X137338850Y-107421556D01* +X137208776Y-107423139D01* +X137110884Y-107427957D01* +X137033605Y-107437299D01* +X136965366Y-107452451D01* +X136894598Y-107474701D01* +X136853234Y-107489748D01* +X136664833Y-107582319D01* +X136512530Y-107702843D01* +X136394867Y-107853094D01* +X136310390Y-108034843D01* +X136257640Y-108249864D01* +X136243573Y-108337285D01* +X136662080Y-108131123D01* +X136678490Y-108123060D01* +X136861222Y-108036355D01* +X137021112Y-107966258D01* +X137141234Y-107919521D01* +X137717541Y-107919521D01* +X137727031Y-107991952D01* +X137754049Y-108069519D01* +X137792313Y-108130902D01* +X137806047Y-108143571D01* +X137859701Y-108168951D01* +X137915019Y-108171633D01* +X137952433Y-108149363D01* +X137960494Y-108113264D01* +X137952140Y-108046682D01* +X137927561Y-107972992D01* +X137891330Y-107910096D01* +X137857378Y-107877425D01* +X137801851Y-107852569D01* +X137751959Y-107856540D01* +X137721633Y-107890913D01* +X137717541Y-107919521D01* +X137141234Y-107919521D01* +X137152512Y-107915133D01* +X137249774Y-107885341D01* +X137394462Y-107851465D01* +X137558542Y-107813074D01* +X137686285Y-107783229D01* +X137782761Y-107760752D01* +X137853038Y-107744466D01* +X137902186Y-107733193D01* +X137935274Y-107725756D01* +X137957370Y-107720977D01* +X137967916Y-107719331D01* +X137991519Y-107722734D01* +X138014376Y-107741302D01* +X138039743Y-107780729D01* +X138070878Y-107846704D01* +X138111039Y-107944920D01* +X138163483Y-108081066D01* +X138171541Y-108102253D01* +X138175745Y-108113264D01* +X138202520Y-108183397D01* +G37* %TO.C,R_LATCH_G1*% +D11* X132131359Y-74060000D02* X132438641Y-74060000D01* X132131359Y-74820000D02* X132438641Y-74820000D01* -%TO.C,U_MCU1*% -X126625000Y-105550000D02* -X127475000Y-105550000D01* -X126625000Y-120850000D02* -X126625000Y-105550000D01* -X126775000Y-120850000D02* -X141925000Y-120850000D01* -X141925000Y-120850000D02* -X141925000Y-102700000D01* -D13* -X126825000Y-101500000D02* -G75* -G02* -X126525000Y-101500000I-150000J0D01* -G01* -X126525000Y-101500000D02* -G75* -G02* -X126825000Y-101500000I150000J0D01* -G01* +%TO.C,R_FB2*% +X138145000Y-100846359D02* +X138145000Y-101153641D01* +X138905000Y-100846359D02* +X138905000Y-101153641D01* +%TO.C,R_VSET1*% +X121923641Y-99370000D02* +X121616359Y-99370000D01* +X121923641Y-100130000D02* +X121616359Y-100130000D01* %TO.C,C_IMU_3*% -D10* -X144857836Y-69640000D02* -X144642164Y-69640000D01* -X144857836Y-70360000D02* -X144642164Y-70360000D01* +X127287836Y-128140000D02* +X127072164Y-128140000D01* +X127287836Y-128860000D02* +X127072164Y-128860000D01* +%TO.C,R_STAT1*% +X124313641Y-96870000D02* +X124006359Y-96870000D01* +X124313641Y-97630000D02* +X124006359Y-97630000D01* +%TO.C,R_ISET1*% +X121943641Y-97870000D02* +X121636359Y-97870000D01* +X121943641Y-98630000D02* +X121636359Y-98630000D01* %TO.C,R_CC1*% X130621359Y-123435000D02* X130928641Y-123435000D01* X130621359Y-124195000D02* X130928641Y-124195000D01* -%TO.C,C_3V3_2*% -X144195000Y-95612836D02* -X144195000Y-95397164D01* -X144915000Y-95612836D02* -X144915000Y-95397164D01* -%TO.C,C_3V3_1*% -X142934420Y-90865000D02* -X143215580Y-90865000D01* -X142934420Y-91885000D02* -X143215580Y-91885000D01* -%TO.C,R_VSYS1*% -X133621359Y-91235000D02* -X133928641Y-91235000D01* -X133621359Y-91995000D02* -X133928641Y-91995000D01* -%TO.C,C_RF_BULK1*% -X145585000Y-96106252D02* -X145585000Y-94683748D01* -X147405000Y-96106252D02* -X147405000Y-94683748D01* -%TO.C,R_I2C_SDA1*% -X125495000Y-102653641D02* -X125495000Y-102346359D01* -X126255000Y-102653641D02* -X126255000Y-102346359D01* -%TO.C,R_I2C_SCL1*% -X125495000Y-100403641D02* -X125495000Y-100096359D01* -X126255000Y-100403641D02* -X126255000Y-100096359D01* -%TO.C,SW_RST1*% -X143975000Y-100075000D02* -X148375000Y-100075000D01* -X143975000Y-100195000D02* -X143975000Y-100075000D01* -X143975000Y-102345000D02* -X143975000Y-101205000D01* -X143975000Y-103475000D02* -X143975000Y-103355000D01* -X148375000Y-100075000D02* -X148375000Y-100195000D01* -X148375000Y-101205000D02* -X148375000Y-102345000D01* -X148375000Y-103355000D02* -X148375000Y-103475000D01* -X148375000Y-103475000D02* -X143975000Y-103475000D01* +%TO.C,R_FB1*% +X138145000Y-99153641D02* +X138145000Y-98846359D01* +X138905000Y-99153641D02* +X138905000Y-98846359D01* +%TO.C,U_XBEE1*% +X120400000Y-103950000D02* +X120400000Y-119350000D01* +X120400000Y-119350000D02* +X125300000Y-121050000D01* +X142600000Y-103950000D02* +X142600000Y-120950000D01* +%TO.C,U_BUCK1*% +X145915000Y-93702500D02* +X145915000Y-95522500D01* +X145915000Y-95522500D02* +X145965000Y-95522500D01* +X145965000Y-93702500D02* +X145915000Y-93702500D01* +X147865000Y-93702500D02* +X147085000Y-93702500D01* +X148985000Y-95522500D02* +X149035000Y-95522500D01* +X149035000Y-93702500D02* +X148985000Y-93702500D01* +X149035000Y-95522500D02* +X149035000Y-93702500D01* +X148985000Y-96062500D02* +X149315000Y-96302500D01* +X149315000Y-95822500D01* +X148985000Y-96062500D01* +G36* +X149315000Y-96302500D02* +G01* +X148985000Y-96062500D01* +X149315000Y-95822500D01* +X149315000Y-96302500D01* +G37* %TO.C,C_IMU_1*% -X141890000Y-68892164D02* -X141890000Y-69107836D01* -X142610000Y-68892164D02* -X142610000Y-69107836D01* -%TO.C,R_VSYS2*% -X135871359Y-91235000D02* -X136178641Y-91235000D01* -X135871359Y-91995000D02* -X136178641Y-91995000D01* +X127092164Y-125540000D02* +X127307836Y-125540000D01* +X127092164Y-126260000D02* +X127307836Y-126260000D01* +%TO.C,L_BUCK1*% +X140140000Y-93640000D02* +X140140000Y-94665000D01* +X140140000Y-93640000D02* +X141165000Y-93640000D01* +X140140000Y-97860000D02* +X140140000Y-96835000D01* +X140140000Y-97860000D02* +X141165000Y-97860000D01* +X144910000Y-93640000D02* +X143885000Y-93640000D01* +X144910000Y-93640000D02* +X144910000Y-94665000D01* +X144910000Y-97860000D02* +X143885000Y-97860000D01* +X144910000Y-97860000D02* +X144910000Y-96835000D01* %TO.C,C_STICK1*% -X145145000Y-76312836D02* -X145145000Y-76097164D01* -X145865000Y-76312836D02* -X145865000Y-76097164D01* +X145145000Y-76097164D02* +X145145000Y-76312836D01* +X145865000Y-76097164D02* +X145865000Y-76312836D01* %TO.C,U_HALL1*% -X127802500Y-65440000D02* -X127802500Y-65490000D01* -X127802500Y-66610000D02* -X127802500Y-67390000D01* -X127802500Y-68510000D02* -X127802500Y-68560000D01* -X127802500Y-68560000D02* -X129322500Y-68560000D01* -X129322500Y-65440000D02* -X127802500Y-65440000D01* -X129322500Y-66440000D02* -X129322500Y-65440000D01* -X129322500Y-68560000D02* -X129322500Y-67560000D01* -X127262500Y-67380000D02* -X127502500Y-67050000D01* -X127022500Y-67050000D01* -X127262500Y-67380000D01* -G36* -X127262500Y-67380000D02* -G01* -X127022500Y-67050000D01* -X127502500Y-67050000D01* -X127262500Y-67380000D01* +X125740000Y-63190000D02* +X125740000Y-64190000D01* +X125740000Y-65310000D02* +X125740000Y-66310000D01* +X125740000Y-66310000D02* +X127260000Y-66310000D01* +X127260000Y-63190000D02* +X125740000Y-63190000D01* +X127260000Y-63240000D02* +X127260000Y-63190000D01* +X127260000Y-65140000D02* +X127260000Y-64360000D01* +X127260000Y-66310000D02* +X127260000Y-66260000D01* +X127800000Y-64370000D02* +X127560000Y-64700000D01* +X128040000Y-64700000D01* +X127800000Y-64370000D01* +G36* +X128040000Y-64700000D02* +G01* +X127560000Y-64700000D01* +X127800000Y-64370000D01* +X128040000Y-64700000D01* G37* %TO.C,Q_INV1*% X124238800Y-84405000D02* @@ -2768,10 +3166,10 @@ X129370000Y-91096359D02* X129370000Y-91403641D01* X130130000Y-91096359D02* X130130000Y-91403641D01* -%TO.C,R_BOOT_PU1*% -X144185000Y-98928641D02* -X144185000Y-98621359D01* -X144945000Y-98928641D02* -X144945000Y-98621359D01* +%TO.C,R_TS1*% +X121923641Y-100870000D02* +X121616359Y-100870000D01* +X121923641Y-101630000D02* +X121616359Y-101630000D01* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-Edge_Cuts.gbr b/PCB/v2.x/production/gerbers/snips_controller-Edge_Cuts.gbr index a10e56f..588f3c7 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-Edge_Cuts.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-Edge_Cuts.gbr @@ -1,11 +1,11 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Profile,NP*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* diff --git a/PCB/v2.x/production/gerbers/snips_controller-F_Cu.gbr b/PCB/v2.x/production/gerbers/snips_controller-F_Cu.gbr index fdcc533..f6db8c6 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-F_Cu.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-F_Cu.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Copper,L1,Top*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -29,110 +29,103 @@ G04 Aperture macros list* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% %AMFreePoly0* -4,1,153,0.406581,0.754743,0.408810,0.754000,0.410000,0.754000,0.411581,0.753743,0.413810,0.753000,0.415000,0.753000,0.416581,0.752743,0.419581,0.751743,0.420236,0.751472,0.421920,0.750630,0.424581,0.749743,0.426536,0.748536,0.427964,0.747108,0.429236,0.746472,0.430536,0.745536,0.431964,0.744108,0.433236,0.743472,0.434536,0.742536,0.442536,0.734536,0.443472,0.733236, -0.444108,0.731964,0.445536,0.730536,0.446472,0.729236,0.447108,0.727964,0.448536,0.726536,0.449743,0.724581,0.450630,0.721920,0.451472,0.720236,0.451743,0.719581,0.452743,0.716581,0.453000,0.715000,0.453000,0.713810,0.453743,0.711581,0.454000,0.710000,0.454000,0.708810,0.454743,0.706581,0.455000,0.705000,0.455000,-0.705000,0.454743,-0.706581,0.454000,-0.708810, -0.454000,-0.710000,0.453743,-0.711581,0.453000,-0.713810,0.453000,-0.715000,0.452743,-0.716581,0.451743,-0.719581,0.451472,-0.720236,0.450630,-0.721920,0.449743,-0.724581,0.448536,-0.726536,0.447108,-0.727964,0.446472,-0.729236,0.445536,-0.730536,0.444108,-0.731964,0.443472,-0.733236,0.442536,-0.734536,0.434536,-0.742536,0.433236,-0.743472,0.431964,-0.744108,0.430536,-0.745536, -0.429236,-0.746472,0.427964,-0.747108,0.426536,-0.748536,0.424581,-0.749743,0.421920,-0.750630,0.420236,-0.751472,0.419581,-0.751743,0.416581,-0.752743,0.415000,-0.753000,0.413810,-0.753000,0.411581,-0.753743,0.410000,-0.754000,0.408810,-0.754000,0.406581,-0.754743,0.405000,-0.755000,-0.405000,-0.755000,-0.406581,-0.754743,-0.408810,-0.754000,-0.410000,-0.754000,-0.411581,-0.753743, --0.413810,-0.753000,-0.415000,-0.753000,-0.416581,-0.752743,-0.419581,-0.751743,-0.420236,-0.751472,-0.421920,-0.750630,-0.424581,-0.749743,-0.426536,-0.748536,-0.427964,-0.747108,-0.429236,-0.746472,-0.430536,-0.745536,-0.431964,-0.744108,-0.433236,-0.743472,-0.434536,-0.742536,-0.442536,-0.734536,-0.443472,-0.733236,-0.444108,-0.731964,-0.445536,-0.730536,-0.446472,-0.729236,-0.447108,-0.727964, --0.448536,-0.726536,-0.449743,-0.724581,-0.450630,-0.721920,-0.451472,-0.720236,-0.451743,-0.719581,-0.452743,-0.716581,-0.453000,-0.715000,-0.453000,-0.713810,-0.453743,-0.711581,-0.454000,-0.710000,-0.454000,-0.708810,-0.454743,-0.706581,-0.455000,-0.705000,-0.455000,0.705000,-0.454743,0.706581,-0.454000,0.708810,-0.454000,0.710000,-0.453743,0.711581,-0.453000,0.713810,-0.453000,0.715000, --0.452743,0.716581,-0.451743,0.719581,-0.451472,0.720236,-0.450630,0.721920,-0.449743,0.724581,-0.448536,0.726536,-0.447108,0.727964,-0.446472,0.729236,-0.445536,0.730536,-0.444108,0.731964,-0.443472,0.733236,-0.442536,0.734536,-0.434536,0.742536,-0.433236,0.743472,-0.431964,0.744108,-0.430536,0.745536,-0.429236,0.746472,-0.427964,0.747108,-0.426536,0.748536,-0.424581,0.749743, --0.421920,0.750630,-0.420236,0.751472,-0.419581,0.751743,-0.416581,0.752743,-0.415000,0.753000,-0.413810,0.753000,-0.411581,0.753743,-0.410000,0.754000,-0.408810,0.754000,-0.406581,0.754743,-0.405000,0.755000,0.405000,0.755000,0.406581,0.754743,0.406581,0.754743,$1*% +4,1,6,0.600000,-0.600000,-0.600000,-0.600000,-0.600000,0.000000,0.000000,0.600000,0.600000,0.600000,0.600000,-0.600000,0.600000,-0.600000,$1*% G04 Aperture macros list end* %TA.AperFunction,SMDPad,CuDef*% -%ADD10RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% +%ADD10RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% %ADD11R,1.050000X0.650000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD12RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% +%ADD12RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD13RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% +%ADD13RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD14RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% +%ADD14R,0.650000X1.050000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD15RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% +%ADD15C,1.000000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD16C,1.000000*% +%ADD16RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD17RoundRect,0.187500X-0.712500X0.187500X-0.712500X-0.187500X0.712500X-0.187500X0.712500X0.187500X0*% +%ADD17RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD18RoundRect,0.150000X-0.750000X0.150000X-0.750000X-0.150000X0.750000X-0.150000X0.750000X0.150000X0*% +%ADD18RoundRect,0.187500X-0.712500X0.187500X-0.712500X-0.187500X0.712500X-0.187500X0.712500X0.187500X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD19RoundRect,0.225000X-0.225000X0.425000X-0.225000X-0.425000X0.225000X-0.425000X0.225000X0.425000X0*% +%ADD19RoundRect,0.150000X-0.750000X0.150000X-0.750000X-0.150000X0.750000X-0.150000X0.750000X0.150000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD20RoundRect,0.150000X0.350000X-0.600000X0.350000X0.600000X-0.350000X0.600000X-0.350000X-0.600000X0*% +%ADD20RoundRect,0.225000X-0.225000X0.425000X-0.225000X-0.425000X0.225000X-0.425000X0.225000X0.425000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD21RoundRect,0.052000X0.198000X0.048000X-0.198000X0.048000X-0.198000X-0.048000X0.198000X-0.048000X0*% +%ADD21RoundRect,0.150000X0.350000X-0.600000X0.350000X0.600000X-0.350000X0.600000X-0.350000X-0.600000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD22FreePoly0,180.000000*% +%ADD22RoundRect,0.150000X-0.150000X-0.625000X0.150000X-0.625000X0.150000X0.625000X-0.150000X0.625000X0*% %TD*% -%TA.AperFunction,ComponentPad*% -%ADD23C,0.300000*% +%TA.AperFunction,SMDPad,CuDef*% +%ADD23RoundRect,0.250000X-0.350000X-0.650000X0.350000X-0.650000X0.350000X0.650000X-0.350000X0.650000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD24RoundRect,0.150000X-0.150000X-0.625000X0.150000X-0.625000X0.150000X0.625000X-0.150000X0.625000X0*% +%ADD24RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD25RoundRect,0.250000X-0.350000X-0.650000X0.350000X-0.650000X0.350000X0.650000X-0.350000X0.650000X0*% +%ADD25R,0.400000X0.800000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD26RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD26R,0.800000X0.400000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD27RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% +%ADD27FreePoly0,270.000000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD28RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% +%ADD28R,1.200000X1.200000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD29RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% +%ADD29R,0.800000X0.800000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD30RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% +%ADD30RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD31RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% +%ADD31RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% %TD*% -%TA.AperFunction,ComponentPad*% -%ADD32O,1.000000X2.100000*% +%TA.AperFunction,SMDPad,CuDef*% +%ADD32RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% %TD*% -%TA.AperFunction,ComponentPad*% -%ADD33O,1.000000X1.600000*% +%TA.AperFunction,SMDPad,CuDef*% +%ADD33RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD34RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% +%ADD34RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD35C,2.550000*% +%ADD35O,1.000000X2.100000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD36C,2.050000*% +%ADD36O,1.000000X1.600000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD37C,2.250000*% +%ADD37C,2.550000*% %TD*% -%TA.AperFunction,SMDPad,CuDef*% -%ADD38RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%TA.AperFunction,ComponentPad*% +%ADD38C,2.050000*% %TD*% -%TA.AperFunction,SMDPad,CuDef*% -%ADD39RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%TA.AperFunction,ComponentPad*% +%ADD39C,2.250000*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD40RoundRect,0.150000X-0.150000X0.512500X-0.150000X-0.512500X0.150000X-0.512500X0.150000X0.512500X0*% +%ADD40RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% -%ADD41R,1.500000X3.600000*% +%ADD41RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% %TD*% %TA.AperFunction,SMDPad,CuDef*% %ADD42RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% @@ -149,32 +142,32 @@ G04 Aperture macros list end* %TA.AperFunction,ComponentPad*% %ADD46O,1.200000X1.750000*% %TD*% -%TA.AperFunction,ViaPad*% -%ADD47C,0.600000*% +%TA.AperFunction,ComponentPad*% +%ADD47C,0.300000*% %TD*% -%TA.AperFunction,Conductor*% -%ADD48C,0.300000*% +%TA.AperFunction,ViaPad*% +%ADD48C,0.600000*% %TD*% %TA.AperFunction,Conductor*% -%ADD49C,0.400000*% +%ADD49C,0.200000*% %TD*% %TA.AperFunction,Conductor*% -%ADD50C,0.200000*% +%ADD50C,0.300000*% %TD*% %TA.AperFunction,Conductor*% -%ADD51C,0.550000*% +%ADD51C,0.400000*% %TD*% %TA.AperFunction,Conductor*% -%ADD52C,0.800000*% +%ADD52C,0.550000*% %TD*% G04 APERTURE END LIST* D10* -%TO.P,C_SYS_1,1*% -%TO.N,VSYS*% -X134750000Y-120315000D03* -%TO.P,C_SYS_1,2*% +%TO.P,C_3V3_3,1*% +%TO.N,3V3*% +X140600000Y-104030000D03* +%TO.P,C_3V3_3,2*% %TO.N,GND*% -X136650000Y-120315000D03* +X140600000Y-103070000D03* %TD*% D11* %TO.P,SW_MACRO4,1*% @@ -187,38 +180,48 @@ X123825000Y-103600000D03* X127975000Y-103600000D03* %TD*% D12* -%TO.P,C_VIN_2,1*% -%TO.N,VBUS*% -X126750000Y-119275000D03* -%TO.P,C_VIN_2,2*% +%TO.P,C_OLED_1,1*% +%TO.N,3V3*% +X124175000Y-105100000D03* +%TO.P,C_OLED_1,2*% %TO.N,GND*% -X126750000Y-118315000D03* +X122625000Y-105100000D03* %TD*% D13* -%TO.P,C_VIN_1,1*% -%TO.N,VBUS*% -X124750000Y-119315000D03* -%TO.P,C_VIN_1,2*% -%TO.N,GND*% -X122850000Y-119315000D03* -%TD*% -D14* -%TO.P,C_BUCK_OUT1,1*% +%TO.P,R_EN_PU1,1*% +%TO.N,/MCU_Core/MCU_EN*% +X145490000Y-118600000D03* +%TO.P,R_EN_PU1,2*% %TO.N,3V3*% -X131475000Y-110750000D03* -%TO.P,C_BUCK_OUT1,2*% -%TO.N,GND*% -X131475000Y-108850000D03* +X146510000Y-118600000D03* %TD*% -D15* +D10* %TO.P,C_RGB1,1*% %TO.N,3V3*% -X127270000Y-123750000D03* +X125800000Y-125080000D03* %TO.P,C_RGB1,2*% %TO.N,GND*% -X128230000Y-123750000D03* +X125800000Y-124120000D03* %TD*% -D16* +D14* +%TO.P,SW_BOOT1,1*% +%TO.N,GND*% +X146075000Y-116575000D03* +X146075000Y-112425000D03* +%TO.P,SW_BOOT1,2*% +%TO.N,/MCU_Core/MCU_BOOT*% +X148225000Y-116575000D03* +X148225000Y-112425000D03* +%TD*% +D10* +%TO.P,C_TRIG1,1*% +%TO.N,/Hall_Trigger/TRIG_ADC*% +X131600000Y-103830000D03* +%TO.P,C_TRIG1,2*% +%TO.N,GND*% +X131600000Y-102870000D03* +%TD*% +D15* %TO.P,FID1,*% %TO.N,*% X126000000Y-61750000D03* @@ -233,32 +236,32 @@ X137075000Y-94250000D03* X132925000Y-96400000D03* X137075000Y-96400000D03* %TD*% -D13* -%TO.P,C_BUCK_IN1,1*% -%TO.N,VSYS*% -X140900000Y-114300000D03* -%TO.P,C_BUCK_IN1,2*% -%TO.N,GND*% -X139000000Y-114300000D03* -%TD*% -D12* -%TO.P,C_SYS_2,1*% -%TO.N,VSYS*% -X132250000Y-120315000D03* -%TO.P,C_SYS_2,2*% +D16* +%TO.P,C_EN1,1*% +%TO.N,/MCU_Core/MCU_EN*% +X145225000Y-120300000D03* +%TO.P,C_EN1,2*% %TO.N,GND*% -X132250000Y-119355000D03* +X146775000Y-120300000D03* %TD*% D17* +%TO.P,R_USB_DM1,1*% +%TO.N,/MCU_Core/USB_DM*% +X128020000Y-114970000D03* +%TO.P,R_USB_DM1,2*% +%TO.N,/MCU_Core/USB_DM_MCU*% +X128020000Y-113950000D03* +%TD*% +D18* %TO.P,SW_THR_UP1,1,1_1*% %TO.N,/Buttons_Direct/BTN_THR_UP*% X122700000Y-72275000D03* X122700000Y-74725000D03* -D18* +D19* %TO.P,SW_THR_UP1,2,2_2*% %TO.N,GND*% X122700000Y-73500000D03* -D19* +D20* %TO.P,SW_THR_UP1,MP*% %TO.N,N/C*% X120750000Y-71650000D03* @@ -292,7 +295,7 @@ X127975000Y-94250000D03* X123825000Y-96400000D03* X127975000Y-96400000D03* %TD*% -D20* +D21* %TO.P,D_RGB1,1*% %TO.N,GND*% X129650000Y-125350000D03* @@ -306,117 +309,251 @@ X127850000Y-128650000D03* %TO.N,N/C*% X129650000Y-128650000D03* %TD*% -D10* -%TO.P,C_BAT1,1*% -%TO.N,VBAT*% -X133250000Y-116815000D03* -%TO.P,C_BAT1,2*% -%TO.N,GND*% -X135150000Y-116815000D03* -%TD*% -D21* -%TO.P,U_CHG1,1,SYS_1*% -%TO.N,VSYS*% -X130800000Y-119115000D03* -%TO.P,U_CHG1,2,BAT_2*% -%TO.N,VBAT*% -X130800000Y-118715000D03* -%TO.P,U_CHG1,3,STAT2_3*% -%TO.N,/MCU_Core/STAT2*% -X130800000Y-118315000D03* -%TO.P,U_CHG1,4,~{CE}_4*% -%TO.N,GND*% -X130800000Y-117915000D03* -%TO.P,U_CHG1,5,GND_5*% -X130800000Y-117515000D03* -%TO.P,U_CHG1,6,TS/MR_6*% -%TO.N,/Power_Charger/CHG_TS*% -X128700000Y-117515000D03* -%TO.P,U_CHG1,7,ILIM/VSET_7*% -%TO.N,/Power_Charger/CHG_VSET*% -X128700000Y-117915000D03* -%TO.P,U_CHG1,8,ISET_8*% -%TO.N,/Power_Charger/CHG_ISET*% -X128700000Y-118315000D03* -%TO.P,U_CHG1,9,STAT1_9*% -%TO.N,/MCU_Core/STAT1*% -X128700000Y-118715000D03* -%TO.P,U_CHG1,10,IN_10*% -%TO.N,VBUS*% -X128700000Y-119115000D03* D22* -%TO.P,U_CHG1,11,THERMAL_PAD_11*% -%TO.N,GND*% -X129750000Y-118315000D03* -D23* -%TO.P,U_CHG1,12*% -X129750000Y-118815000D03* -%TO.P,U_CHG1,13*% -X129750000Y-117815000D03* -%TD*% -D24* %TO.P,U_OLED1,1,GND_1*% %TO.N,GND*% -X122900000Y-106125000D03* +X122900000Y-108125000D03* %TO.P,U_OLED1,2,VCC_2*% %TO.N,3V3*% -X123900000Y-106125000D03* +X123900000Y-108125000D03* %TO.P,U_OLED1,3,SDA_3*% %TO.N,/Accelerometer/I2C_SDA*% -X124900000Y-106125000D03* +X124900000Y-108125000D03* %TO.P,U_OLED1,4,SCL_4*% %TO.N,/Accelerometer/I2C_SCL*% -X125900000Y-106125000D03* -D25* +X125900000Y-108125000D03* +D23* %TO.P,U_OLED1,MP*% %TO.N,N/C*% -X121600000Y-110000000D03* -X127200000Y-110000000D03* -%TD*% -D26* -%TO.P,R_STAT2,1*% -%TO.N,/MCU_Core/STAT2*% -X133840000Y-114515000D03* -%TO.P,R_STAT2,2*% -%TO.N,3V3*% -X134860000Y-114515000D03* +X121600000Y-112000000D03* +X127200000Y-112000000D03* %TD*% -D16* +D15* %TO.P,FID2,*% %TO.N,*% X143750000Y-61750000D03* %TD*% -D26* -%TO.P,R_FB2,1*% -%TO.N,/Power_Buck/BUCK_FB*% -X133230000Y-106725000D03* -%TO.P,R_FB2,2*% +D24* +%TO.P,C_OLED_2,1*% +%TO.N,3V3*% +X123880000Y-106300000D03* +%TO.P,C_OLED_2,2*% %TO.N,GND*% -X134250000Y-106725000D03* +X122920000Y-106300000D03* %TD*% +D25* +%TO.P,U_MCU1,1*% +%TO.N,GND*% +X142450000Y-105500000D03* +%TO.P,U_MCU1,2*% +X141600000Y-105500000D03* +%TO.P,U_MCU1,3*% +%TO.N,3V3*% +X140750000Y-105500000D03* +%TO.P,U_MCU1,4*% +%TO.N,/MCU_Core/MCU_BOOT*% +X139900000Y-105500000D03* +%TO.P,U_MCU1,5*% +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X139050000Y-105500000D03* +%TO.P,U_MCU1,6*% +%TO.N,/Buttons_Direct/BTN_MACRO6*% +X138200000Y-105500000D03* +%TO.P,U_MCU1,7*% +%TO.N,N/C*% +X137350000Y-105500000D03* +%TO.P,U_MCU1,8*% +%TO.N,/Buttons_Direct/BTN_MACRO3*% +X136500000Y-105500000D03* +%TO.P,U_MCU1,9*% +%TO.N,/Buttons_Direct/BTN_MACRO2*% +X135650000Y-105500000D03* +%TO.P,U_MCU1,10*% +%TO.N,/MCU_Core/STICK_Y*% +X134800000Y-105500000D03* +%TO.P,U_MCU1,11*% +%TO.N,/MCU_Core/STICK_X*% +X133950000Y-105500000D03* +%TO.P,U_MCU1,12*% +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X133100000Y-105500000D03* +%TO.P,U_MCU1,13*% +%TO.N,/Hall_Trigger/TRIG_ADC*% +X132250000Y-105500000D03* +%TO.P,U_MCU1,14*% +%TO.N,/MCU_Core/VSYS_SENSE*% +X131400000Y-105500000D03* +%TO.P,U_MCU1,15*% +%TO.N,/Buttons_Direct/BTN_MACRO4*% +X130550000Y-105500000D03* +D26* +%TO.P,U_MCU1,16*% +%TO.N,/Accelerometer/I2C_SDA*% +X129500000Y-106550000D03* +%TO.P,U_MCU1,17*% +%TO.N,/Accelerometer/I2C_SCL*% +X129500000Y-107400000D03* +%TO.P,U_MCU1,18*% +%TO.N,/MCU_Core/STAT2*% +X129500000Y-108250000D03* +%TO.P,U_MCU1,19*% +%TO.N,/MCU_Core/STAT1*% +X129500000Y-109100000D03* +%TO.P,U_MCU1,20*% +%TO.N,/Buttons_Direct/BTN_MACRO1*% +X129500000Y-109950000D03* +%TO.P,U_MCU1,21*% +%TO.N,/MCU_Core/BTN_STICK*% +X129500000Y-110800000D03* +%TO.P,U_MCU1,22*% +%TO.N,/Buttons_Direct/BTN_THR_DN*% +X129500000Y-111650000D03* +%TO.P,U_MCU1,23*% +%TO.N,/MCU_Core/USB_DM_MCU*% +X129500000Y-112500000D03* +%TO.P,U_MCU1,24*% +%TO.N,/MCU_Core/USB_DP_MCU*% +X129500000Y-113350000D03* +%TO.P,U_MCU1,25*% +%TO.N,/MCU_Core/PWR_BTN_SENSE*% +X129500000Y-114200000D03* +%TO.P,U_MCU1,26*% +%TO.N,N/C*% +X129500000Y-115050000D03* +%TO.P,U_MCU1,27*% +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X129500000Y-115900000D03* +%TO.P,U_MCU1,28*% +%TO.N,/Buttons_Direct/BTN_THR_UP*% +X129500000Y-116750000D03* +%TO.P,U_MCU1,29*% +%TO.N,/XBee/XBEE_CTS*% +X129500000Y-117600000D03* +%TO.P,U_MCU1,30*% +%TO.N,/MCU_Core/RGB_DIN*% +X129500000Y-118450000D03* +D25* +%TO.P,U_MCU1,31*% +%TO.N,/XBee/XBEE_DIN*% +X130550000Y-119500000D03* +%TO.P,U_MCU1,32*% +%TO.N,/XBee/XBEE_DOUT*% +X131400000Y-119500000D03* +%TO.P,U_MCU1,33*% +%TO.N,ACCEL_INT1*% +X132250000Y-119500000D03* +%TO.P,U_MCU1,34*% +%TO.N,/Buttons_Direct/BTN_VOL_UP*% +X133100000Y-119500000D03* +%TO.P,U_MCU1,35*% +%TO.N,/XBee/XBEE_RTS*% +X133950000Y-119500000D03* +%TO.P,U_MCU1,36*% +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X134800000Y-119500000D03* +%TO.P,U_MCU1,37*% +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135650000Y-119500000D03* +%TO.P,U_MCU1,38*% +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-119500000D03* +%TO.P,U_MCU1,39*% +%TO.N,N/C*% +X137350000Y-119500000D03* +%TO.P,U_MCU1,40*% +%TO.N,/MCU_Core/PWR_HOLD*% +X138200000Y-119500000D03* +%TO.P,U_MCU1,41*% +%TO.N,N/C*% +X139050000Y-119500000D03* +%TO.P,U_MCU1,42*% +%TO.N,GND*% +X139900000Y-119500000D03* +%TO.P,U_MCU1,43*% +X140750000Y-119500000D03* +%TO.P,U_MCU1,44*% +%TO.N,N/C*% +X141600000Y-119500000D03* +%TO.P,U_MCU1,45*% +%TO.N,/MCU_Core/MCU_EN*% +X142450000Y-119500000D03* +D26* +%TO.P,U_MCU1,46*% +%TO.N,GND*% +X143500000Y-118450000D03* +%TO.P,U_MCU1,47*% +X143500000Y-117600000D03* +%TO.P,U_MCU1,48*% +X143500000Y-116750000D03* +%TO.P,U_MCU1,49*% +X143500000Y-115900000D03* +%TO.P,U_MCU1,50*% +X143500000Y-115050000D03* +%TO.P,U_MCU1,51*% +X143500000Y-114200000D03* +%TO.P,U_MCU1,52*% +X143500000Y-113350000D03* +%TO.P,U_MCU1,53*% +X143500000Y-112500000D03* +%TO.P,U_MCU1,54*% +X143500000Y-111650000D03* +%TO.P,U_MCU1,55*% +X143500000Y-110800000D03* +%TO.P,U_MCU1,56*% +X143500000Y-109950000D03* +%TO.P,U_MCU1,57*% +X143500000Y-109100000D03* +%TO.P,U_MCU1,58*% +X143500000Y-108250000D03* +%TO.P,U_MCU1,59*% +X143500000Y-107400000D03* +%TO.P,U_MCU1,60*% +X143500000Y-106550000D03* D27* +%TO.P,U_MCU1,61*% +X138150000Y-110850000D03* +D28* +X136500000Y-110850000D03* +X134850000Y-110850000D03* +X138150000Y-112500000D03* +X136500000Y-112500000D03* +X134850000Y-112500000D03* +X138150000Y-114150000D03* +X136500000Y-114150000D03* +X134850000Y-114150000D03* +D29* +%TO.P,U_MCU1,62*% +X143500000Y-105500000D03* +%TO.P,U_MCU1,63*% +X129500000Y-105500000D03* +%TO.P,U_MCU1,64*% +X129500000Y-119500000D03* +%TO.P,U_MCU1,65*% +X143500000Y-119500000D03* +%TD*% +D30* %TO.P,SW_VOL_DN1,1,1_1*% %TO.N,/Buttons_Direct/BTN_VOL_DN*% X147300000Y-84725000D03* X147300000Y-82275000D03* -D28* +D31* %TO.P,SW_VOL_DN1,2,2_2*% %TO.N,GND*% X147300000Y-83500000D03* -D29* +D32* %TO.P,SW_VOL_DN1,MP*% %TO.N,N/C*% X149250000Y-85350000D03* X149250000Y-81650000D03* %TD*% -D30* +D33* %TO.P,J_USB1,A1,GND_A1*% %TO.N,GND*% X133750000Y-123105000D03* %TO.P,J_USB1,A4,VBUS_A4*% %TO.N,VBUS*% X134550000Y-123105000D03* -D31* +D34* %TO.P,J_USB1,A5,CC1_A5*% %TO.N,/USB_C/USB_CC1*% X135750000Y-123105000D03* @@ -429,7 +566,7 @@ X137250000Y-123105000D03* %TO.P,J_USB1,A8,SBU1_A8*% %TO.N,N/C*% X138250000Y-123105000D03* -D30* +D33* %TO.P,J_USB1,A9,VBUS_A9*% %TO.N,VBUS*% X139450000Y-123105000D03* @@ -441,7 +578,7 @@ X140250000Y-123105000D03* %TO.P,J_USB1,B4,VBUS_B4*% %TO.N,VBUS*% X139450000Y-123105000D03* -D31* +D34* %TO.P,J_USB1,B5,CC2_B5*% %TO.N,/USB_C/USB_CC2*% X138750000Y-123105000D03* @@ -454,39 +591,31 @@ X136250000Y-123105000D03* %TO.P,J_USB1,B8,SBU2_B8*% %TO.N,N/C*% X135250000Y-123105000D03* -D30* +D33* %TO.P,J_USB1,B9,VBUS_B9*% %TO.N,VBUS*% X134550000Y-123105000D03* %TO.P,J_USB1,B12,GND_B12*% %TO.N,GND*% X133750000Y-123105000D03* -D32* +D35* %TO.P,J_USB1,SH,SHIELD_SH*% X132680000Y-124020000D03* -D33* +D36* X132680000Y-128200000D03* -D32* +D35* X141320000Y-124020000D03* -D33* +D36* X141320000Y-128200000D03* %TD*% -D34* -%TO.P,R_VSET1,1*% -%TO.N,/Power_Charger/CHG_VSET*% -X122770000Y-115500000D03* -%TO.P,R_VSET1,2*% -%TO.N,GND*% -X121750000Y-115500000D03* -%TD*% -D35* +D37* %TO.P,J_STICK1,*% %TO.N,*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D36* +D38* %TO.P,J_STICK1,1,X_LO_1*% %TO.N,GND*% X137500000Y-69770000D03* @@ -499,11 +628,11 @@ X135000000Y-69770000D03* %TO.N,/MCU_Core/STICK_Y*% X143730000Y-78500000D03* %TO.P,J_STICK1,3,X_HI_3*% -%TO.N,/MCU_Core/3V3_RF*% +%TO.N,3V3*% X132500000Y-69770000D03* %TO.P,J_STICK1,3',Y_HI_3'*% X143730000Y-76000000D03* -D37* +D39* %TO.P,J_STICK1,a,SW_A_a*% %TO.N,/MCU_Core/BTN_STICK*% X131750000Y-84250000D03* @@ -517,22 +646,7 @@ X131750000Y-88750000D03* %TO.N,N/C*% X138250000Y-88750000D03* %TD*% -D34* -%TO.P,R_STAT1,1*% -%TO.N,/MCU_Core/STAT1*% -X125670000Y-117315000D03* -%TO.P,R_STAT1,2*% -%TO.N,3V3*% -X124650000Y-117315000D03* -%TD*% -%TO.P,R_ISET1,1*% -%TO.N,/Power_Charger/CHG_ISET*% -X122790000Y-116515000D03* -%TO.P,R_ISET1,2*% -%TO.N,GND*% -X121770000Y-116515000D03* -%TD*% -D38* +D24* %TO.P,C_DBNC1,1*% %TO.N,/MCU_Core/PWR_BTN_SENSE*% X124080000Y-125200000D03* @@ -540,82 +654,96 @@ X124080000Y-125200000D03* %TO.N,GND*% X123120000Y-125200000D03* %TD*% -D26* +D17* %TO.P,R_RGB1,1*% %TO.N,/RGB_LED/RGB_DIN_R*% -X127240000Y-122600000D03* +X127900000Y-123500000D03* %TO.P,R_RGB1,2*% %TO.N,/MCU_Core/RGB_DIN*% -X128260000Y-122600000D03* +X127900000Y-122480000D03* %TD*% -D39* -%TO.P,R_FB1,1*% -%TO.N,/Power_Buck/BUCK_FB*% -X131975000Y-106040000D03* -%TO.P,R_FB1,2*% +D10* +%TO.P,C_3V3_2,1*% %TO.N,3V3*% -X131975000Y-107060000D03* +X140600000Y-102080000D03* +%TO.P,C_3V3_2,2*% +%TO.N,GND*% +X140600000Y-101120000D03* %TD*% -D17* +D40* +%TO.P,C_3V3_1,1*% +%TO.N,3V3*% +X145300000Y-106775000D03* +%TO.P,C_3V3_1,2*% +%TO.N,GND*% +X145300000Y-105225000D03* +%TD*% +D41* +%TO.P,R_VSYS1,1*% +%TO.N,VSYS*% +X129800000Y-100900000D03* +%TO.P,R_VSYS1,2*% +%TO.N,/MCU_Core/VSYS_SENSE*% +X129800000Y-101920000D03* +%TD*% +%TO.P,R_I2C_SDA1,1*% +%TO.N,3V3*% +X125500000Y-105280000D03* +%TO.P,R_I2C_SDA1,2*% +%TO.N,/Accelerometer/I2C_SDA*% +X125500000Y-106300000D03* +%TD*% +D18* %TO.P,SW_THR_DN1,1,1_1*% %TO.N,/Buttons_Direct/BTN_THR_DN*% X122700000Y-82275000D03* X122700000Y-84725000D03* -D18* +D19* %TO.P,SW_THR_DN1,2,2_2*% %TO.N,GND*% X122700000Y-83500000D03* -D19* +D20* %TO.P,SW_THR_DN1,MP*% %TO.N,N/C*% X120750000Y-81650000D03* X120750000Y-85350000D03* %TD*% -D27* +D41* +%TO.P,R_I2C_SCL1,1*% +%TO.N,3V3*% +X127200000Y-106390000D03* +%TO.P,R_I2C_SCL1,2*% +%TO.N,/Accelerometer/I2C_SCL*% +X127200000Y-107410000D03* +%TD*% +D30* %TO.P,SW_VOL_UP1,1,1_1*% %TO.N,/Buttons_Direct/BTN_VOL_UP*% X147300000Y-74725000D03* X147300000Y-72275000D03* -D28* +D31* %TO.P,SW_VOL_UP1,2,2_2*% %TO.N,GND*% X147300000Y-73500000D03* -D29* +D32* %TO.P,SW_VOL_UP1,MP*% %TO.N,N/C*% X149250000Y-75350000D03* X149250000Y-71650000D03* %TD*% -D40* -%TO.P,U_BUCK1,1,EN_1*% -%TO.N,/Power_Buck/PWR_EN*% -X141875000Y-109800000D03* -%TO.P,U_BUCK1,2,GND_2*% -%TO.N,GND*% -X140925000Y-109800000D03* -%TO.P,U_BUCK1,3,SW_3*% -%TO.N,/Power_Buck/BUCK_SW*% -X139975000Y-109800000D03* -%TO.P,U_BUCK1,4,VIN_4*% -%TO.N,VSYS*% -X139975000Y-112075000D03* -%TO.P,U_BUCK1,5,FB_5*% -%TO.N,/Power_Buck/BUCK_FB*% -X141875000Y-112075000D03* -%TD*% -D41* -%TO.P,L_BUCK1,1,1_1*% -%TO.N,/Power_Buck/BUCK_SW*% -X137500000Y-109800000D03* -%TO.P,L_BUCK1,2,2_2*% -%TO.N,3V3*% -X134450000Y-109800000D03* -%TD*% -D16* +D15* %TO.P,FID3,*% %TO.N,*% X148500000Y-121000000D03* %TD*% +D41* +%TO.P,R_VSYS2,1*% +%TO.N,/MCU_Core/VSYS_SENSE*% +X130000000Y-102890000D03* +%TO.P,R_VSYS2,2*% +%TO.N,GND*% +X130000000Y-103910000D03* +%TD*% D42* %TO.P,SW_PWR1,1,1_1*% %TO.N,/MCU_Core/PWR_BTN_SENSE*% @@ -631,6 +759,14 @@ D44* X121150000Y-128950000D03* X124850000Y-128950000D03* %TD*% +D17* +%TO.P,R_USB_DP1,1*% +%TO.N,/MCU_Core/USB_DP*% +X128020000Y-116910000D03* +%TO.P,R_USB_DP1,2*% +%TO.N,/MCU_Core/USB_DP_MCU*% +X128020000Y-115890000D03* +%TD*% D11* %TO.P,SW_MACRO5,1*% %TO.N,/Buttons_Direct/BTN_MACRO5*% @@ -641,13 +777,13 @@ X137075000Y-101450000D03* X132925000Y-103600000D03* X137075000Y-103600000D03* %TD*% -D34* -%TO.P,R_TS1,1*% -%TO.N,/Power_Charger/CHG_TS*% -X122770000Y-114500000D03* -%TO.P,R_TS1,2*% -%TO.N,GND*% -X121750000Y-114500000D03* +D17* +%TO.P,R_BOOT_PU1,1*% +%TO.N,/MCU_Core/MCU_BOOT*% +X145800000Y-109920000D03* +%TO.P,R_BOOT_PU1,2*% +%TO.N,3V3*% +X145800000Y-108900000D03* %TD*% D45* %TO.P,BT1,1,Pin_1_1*% @@ -659,1203 +795,1201 @@ D46* X147200000Y-123100000D03* %TD*% D47* -%TO.N,VSYS*% -X131134999Y-72039999D03* -X133551500Y-90667500D03* -X131197200Y-105109200D03* -X135775300Y-108336200D03* -X127561250Y-90824999D03* +%TO.P,U_CHG1,12*% +%TO.N,GND*% +X128750000Y-95750000D03* +%TO.P,U_CHG1,13*% +X128750000Y-96750000D03* +%TD*% +D48* +%TO.N,3V3*% +X127761250Y-93014999D03* +X145311599Y-107614004D03* +X136012023Y-99792121D03* +X131100000Y-101100000D03* +X132248535Y-126920005D03* +X127200000Y-127762500D03* +X124950000Y-104123528D03* +X134200000Y-106400000D03* +X125080000Y-124896016D03* +X123900000Y-98100000D03* +X141068110Y-104176936D03* +X130620864Y-129450000D03* +X129000000Y-64600000D03* +X126320000Y-106400000D03* +X145500000Y-117780000D03* +X138500000Y-93250000D03* +X137400000Y-100200000D03* %TO.N,GND*% -X144000000Y-94500000D03* -X131800000Y-124350000D03* -X130449999Y-67550000D03* -X143750000Y-70550000D03* -X123950000Y-83200000D03* -X121300000Y-107150000D03* -X142800000Y-95850000D03* -X139100000Y-103700000D03* -X122350000Y-105150000D03* -X131800000Y-96500000D03* -X136300000Y-95300000D03* -X121750000Y-119315000D03* -X122600000Y-125750000D03* -X128750000Y-124300000D03* -X123150000Y-85600000D03* -X123050000Y-95850000D03* -X140500000Y-108600000D03* -X128750000Y-103050000D03* -X122600000Y-124650000D03* -X146500000Y-67450000D03* -X135250000Y-106825000D03* -X140800000Y-122150000D03* -X142850000Y-95000000D03* -X136250000Y-117315000D03* -X134600000Y-103700000D03* -X130500000Y-92300000D03* -X129870634Y-119615000D03* -X131450000Y-117565000D03* -X145300000Y-75100000D03* -X136400000Y-100400000D03* -X140000000Y-69400000D03* -X134700000Y-63950000D03* -X135450000Y-103800000D03* -X137850000Y-104150000D03* -X133000000Y-119265000D03* -X129000000Y-96550000D03* -X148500000Y-83050000D03* +X140600000Y-118700000D03* +X126900000Y-123500000D03* +X128300000Y-97700000D03* +X128700000Y-100300000D03* +X139600000Y-114100000D03* +X130850000Y-97425000D03* +X130700000Y-63800000D03* +X139100000Y-70700000D03* +X132500000Y-67000000D03* +X145400000Y-88100000D03* +X137500000Y-97750000D03* +X135250000Y-97250000D03* +X124200000Y-71800000D03* +X134900000Y-64600000D03* +X147050000Y-96950000D03* +X146248528Y-83299999D03* +X124200000Y-64800000D03* +X145600000Y-73000000D03* +X124750000Y-96250000D03* +X131300000Y-117800000D03* +X130800000Y-106700000D03* +X122600000Y-104000000D03* +X142000000Y-114200000D03* +X124100000Y-83700000D03* +X140400000Y-100300000D03* +X121800000Y-96700000D03* +X137799998Y-103000000D03* +X135250000Y-95750000D03* X136285000Y-75940000D03* -X144550000Y-69350000D03* -X143300000Y-102350000D03* -X143200000Y-90650000D03* -X132150000Y-104150000D03* -X130449999Y-103700000D03* -X141700000Y-70000000D03* -X137400000Y-125800000D03* -X123950000Y-73200000D03* -X137450000Y-114300000D03* -X129770634Y-116815000D03* -X131900000Y-100400000D03* -X144950000Y-110700000D03* -X148500000Y-73050000D03* -X143300000Y-106450000D03* -X137050000Y-92150000D03* +X131800000Y-100500000D03* +X128349799Y-95084604D03* +X132000000Y-95300000D03* X131785000Y-73440000D03* -X142800000Y-103050000D03* -X136050000Y-101250000D03* -X141950000Y-79700000D03* -X129800000Y-64050000D03* -X139850000Y-87250000D03* -X145350000Y-93100000D03* -X130950000Y-107800000D03* -X142800000Y-126600000D03* -X146350000Y-66599999D03* -X145450000Y-95800000D03* -X134550000Y-101250000D03* -X147450000Y-106450000D03* -X123050000Y-103050000D03* -X136250000Y-118815000D03* -X147450000Y-102350000D03* -X142900000Y-67400000D03* -X145400000Y-103050000D03* -X123000000Y-104550000D03* -X133199999Y-122150000D03* -X130400000Y-126300000D03* -X125750000Y-118315000D03* -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X129800000Y-100700000D03* -%TO.N,VBUS*% -X125770000Y-125525300D03* -X134650000Y-121702500D03* -X139450000Y-121868900D03* -X141321300Y-92762500D03* -X141703000Y-89578400D03* -X149218700Y-96601800D03* -%TO.N,3V3*% -X131950000Y-112300000D03* -X127300000Y-121550001D03* -X123900000Y-113658400D03* -X146120300Y-98555000D03* -X124549200Y-107406100D03* -X123860000Y-116915000D03* -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X131797000Y-95119100D03* +X122500000Y-125200000D03* +%TO.N,/MCU_Core/MCU_BOOT*% +X139900000Y-106400000D03* +X144900000Y-108300000D03* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X130070634Y-92600000D03* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X124754600Y-83434100D03* -X132620800Y-86688200D03* +X121873930Y-107063387D03* +X130300000Y-116600000D03* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X139209300Y-100184300D03* -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X139789800Y-98443100D03* +X141300000Y-106600000D03* +X142600000Y-102400000D03* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X129065000Y-94095500D03* -%TO.N,VBAT*% -X133810600Y-118937400D03* -%TO.N,/MCU_Core/STAT2*% -X130387500Y-96500000D03* -%TO.N,/MCU_Core/STAT1*% -X123374265Y-117590735D03* +X128200000Y-105450002D03* +X130400000Y-109900000D03* %TO.N,/Accelerometer/I2C_SDA*% -X132254800Y-65652100D03* -X124959600Y-104749000D03* +X124200000Y-111600000D03* +X124600000Y-109800000D03* +X121874741Y-124680758D03* %TO.N,/Accelerometer/I2C_SCL*% -X121327800Y-96462500D03* -X126003900Y-70995100D03* -X126735300Y-100400000D03* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X145804700Y-84769200D03* -%TO.N,/USB_C/USB_CC1*% -X135750000Y-121500900D03* -%TO.N,/MCU_Core/USB_DP*% -X148072200Y-111842500D03* -X139484600Y-96501700D03* -%TO.N,/MCU_Core/USB_DM*% -X137901700Y-95241600D03* -%TO.N,/USB_C/USB_CC2*% -X138750000Y-126065000D03* -%TO.N,/MCU_Core/STICK_X*% -X126670100Y-93676600D03* -%TO.N,/MCU_Core/STICK_Y*% -X130207300Y-95609600D03* -%TO.N,/MCU_Core/3V3_RF*% -X142999700Y-92385900D03* +X125800000Y-109700000D03* +X122700000Y-114100000D03* +X121100000Y-124880210D03* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X138900000Y-106200000D03* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X133300000Y-100800000D03* +X133100000Y-107000000D03* +X136161765Y-101138235D03* +%TO.N,/MCU_Core/STAT2*% +X130824265Y-108075735D03* +%TO.N,/MCU_Core/STAT1*% +X130800000Y-108900000D03* +X127500000Y-99000000D03* +X126150000Y-97470100D03* %TO.N,/MCU_Core/BTN_STICK*% -X134709100Y-92787200D03* +X130500000Y-110800000D03* +X126600000Y-100400000D03* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X145452900Y-98045000D03* -X120688600Y-97070100D03* +X120600000Y-125765642D03* +X130500000Y-114200000D03* +X124000000Y-119600000D03* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X131000000Y-62700000D03* +X122300000Y-87800000D03* +X131700000Y-115100000D03* +X124500000Y-67800000D03* +X121893900Y-106234827D03* +%TO.N,/XBee/XBEE_CTS*% +X127800000Y-117800000D03* %TO.N,/MCU_Core/RGB_DIN*% -X129216700Y-123115100D03* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X123557800Y-90439600D03* -%TO.N,/Buttons_Direct/BTN_VOL_UP*% -X135734500Y-92661400D03* -%TO.N,/Power_Buck/PWR_EN*% -X145850800Y-107623700D03* -X145980700Y-85815700D03* -X141116700Y-110981600D03* -%TO.N,/Buttons_Direct/BTN_MACRO5*% -X136150000Y-104250000D03* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X127525700Y-92504700D03* -X129861700Y-101982200D03* +X126002198Y-123340339D03* +X130400000Y-117400000D03* +%TO.N,/XBee/XBEE_DIN*% +X130179998Y-120689999D03* +%TO.N,/XBee/XBEE_DOUT*% +X131615136Y-118535318D03* %TO.N,ACCEL_INT1*% -X129871400Y-99693700D03* -X139636800Y-97508700D03* -X147014800Y-76170200D03* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X134775000Y-95096400D03* -X135000000Y-61269100D03* -X134105300Y-87305100D03* +X139400000Y-116900000D03* +%TO.N,/Buttons_Direct/BTN_VOL_UP*% +X147034358Y-98156239D03* +X133000000Y-118200000D03* +%TO.N,/XBee/XBEE_RTS*% +X133900000Y-118200000D03* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147700000Y-98600000D03* +X134700000Y-117700000D03* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135600000Y-118300000D03* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-118300000D03* %TO.N,/MCU_Core/PWR_HOLD*% +X140950000Y-90700000D03* X138485000Y-72539999D03* -X129625000Y-98237500D03* -%TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127260700Y-66852300D03* -X126692500Y-80628700D03* -%TD*% +X142000000Y-107300000D03* +%TO.N,VBUS*% +X123750000Y-95250000D03* +X137000000Y-124900000D03* +X122300000Y-102800000D03* +%TO.N,/USB_C/USB_CC1*% +X129200000Y-123700000D03* +%TO.N,/USB_C/USB_CC2*% +X142300000Y-124900000D03* %TO.N,VSYS*% -D48* -X139975000Y-112075000D02* -X139975000Y-113375000D01* +X129700000Y-93350000D03* +X142100000Y-79300000D03* +X144800000Y-90650000D03* +X144600000Y-86300000D03* +%TO.N,VBAT*% +X135900000Y-99000000D03* +X147300000Y-109300000D03* +%TO.N,/Power_Buck/BUCK_FB*% +X139885887Y-98225129D03* +X139500000Y-94850000D03* +%TD*% +%TO.N,3V3*% D49* -X130351700Y-79389400D02* -X130351700Y-72823300D01* +X128900000Y-127600000D02* +X127850000Y-128650000D01* D50* -X141150000Y-114300000D02* -X140900000Y-114300000D01* -X132250000Y-120315000D02* -X134750000Y-120315000D01* -D49* -X131197200Y-100472400D02* -X131197200Y-105109200D01* -X134750000Y-119274800D02* -X135959800Y-118065000D01* -X135959800Y-118065000D02* -X136547400Y-118065000D01* -D48* -X139975000Y-113375000D02* -X140900000Y-114300000D01* +X123880000Y-106300000D02* +X123880000Y-108105000D01* D49* -X133551500Y-92035900D02* -X131091100Y-94496300D01* -X127561000Y-90825000D02* -X126968700Y-90232700D01* -X140900000Y-114300000D02* -X138936100Y-116263900D01* -X131091100Y-100366300D02* -X131197200Y-100472400D01* -X133551500Y-90667500D02* -X133551500Y-92035900D01* -X126968700Y-90232700D02* -X126968700Y-82772400D01* +X125134276Y-125080000D02* +X125800000Y-125080000D01* +X130620864Y-128030312D02* +X130190552Y-127600000D01* +X146510000Y-118600000D02* +X145690000Y-117780000D01* +X130620864Y-129450000D02* +X130620864Y-128030312D01* +X140600000Y-102080000D02* +X140490000Y-102190000D01* +X145800000Y-107275000D02* +X145800000Y-108900000D01* +X125080000Y-124896016D02* +X125080000Y-125025724D01* +X125500000Y-105280000D02* +X125500000Y-104673528D01* +X145300000Y-106775000D02* +X145800000Y-107275000D01* +X125080000Y-125025724D02* +X125134276Y-125080000D01* +X139990000Y-102690000D02* +X140600000Y-102080000D01* +X145300000Y-106775000D02* +X145300000Y-107602405D01* D50* -X134750000Y-119190501D02* -X134750000Y-120315000D01* +X124950000Y-104123528D02* +X124180000Y-104893528D01* D49* -X130351700Y-72823300D02* -X131135000Y-72040000D01* -X126968700Y-82772400D02* -X130351700Y-79389400D01* +X140600000Y-105350000D02* +X140750000Y-105500000D01* +X139990000Y-103420000D02* +X139990000Y-102690000D01* D50* -X130800000Y-119115000D02* -X130800000Y-119765000D01* +X123880000Y-108105000D02* +X123900000Y-108125000D01* D49* -X135775300Y-113690700D02* -X135775300Y-108336200D01* -X131091100Y-94496300D02* -X131091100Y-100366300D01* -X136547400Y-118065000D02* -X138348500Y-116263900D01* +X140921174Y-104030000D02* +X141068110Y-104176936D01* +X140600000Y-104030000D02* +X140600000Y-105350000D01* +X125500000Y-104673528D02* +X124950000Y-104123528D01* +X127200000Y-106390000D02* +X126330000Y-106390000D01* D50* -X131350000Y-120315000D02* -X132250000Y-120315000D01* +X124180000Y-106000000D02* +X123880000Y-106300000D01* D49* -X138348500Y-116263900D02* -X135775300Y-113690700D01* -X138936100Y-116263900D02* -X138348500Y-116263900D01* +X140600000Y-104030000D02* +X139990000Y-103420000D01* +X140600000Y-104030000D02* +X140921174Y-104030000D01* +X145300000Y-107602405D02* +X145311599Y-107614004D01* +X126330000Y-106390000D02* +X126320000Y-106400000D01* +X145690000Y-117780000D02* +X145500000Y-117780000D01* D50* -X130800000Y-119765000D02* -X131350000Y-120315000D01* +X124180000Y-104893528D02* +X124180000Y-106000000D01* +D49* +X130190552Y-127600000D02* +X128900000Y-127600000D01* %TO.N,GND*% -X122600000Y-105400000D02* -X122350000Y-105150000D01* -D48* -X136650000Y-120315000D02* -X136650000Y-119215000D01* -D50* -X123175000Y-95975000D02* -X123400000Y-95975000D01* -D48* -X140925000Y-109800000D02* -X140925000Y-109025000D01* -D50* -X142550000Y-103300000D02* -X142800000Y-103050000D01* -X129650000Y-125550000D02* -X129650000Y-125350000D01* -X148200000Y-83200000D02* -X148350000Y-83200000D01* -X123600000Y-83200000D02* -X123950000Y-83200000D01* -X145650000Y-96000000D02* -X145450000Y-95800000D01* -D48* -X140925000Y-109025000D02* -X140500000Y-108600000D01* +X124600000Y-96400000D02* +X124750000Y-96250000D01* +X146100000Y-73500000D02* +X145600000Y-73000000D01* +X126410000Y-124730000D02* +X126410000Y-125500552D01* +X140600000Y-103070000D02* +X141495000Y-103070000D01* +X131200000Y-117800000D02* +X131300000Y-117800000D01* +X132330000Y-103600000D02* +X131600000Y-102870000D01* +X136500000Y-112500000D02* +X136500000Y-110850000D01* +X137500000Y-69770000D02* +X138170000Y-69770000D01* +X146075000Y-116575000D02* +X144175000Y-116575000D01* +X137799998Y-103000000D02* +X137675000Y-103000000D01* +X129500000Y-119500000D02* +X131200000Y-117800000D01* +X146500000Y-96400000D02* +X147050000Y-96950000D01* +X131600000Y-102870000D02* +X131800000Y-102670000D01* +X125800000Y-124120000D02* +X126410000Y-124730000D01* +X137500000Y-69770000D02* +X137500000Y-67200000D01* +X123000000Y-125320000D02* +X123120000Y-125200000D01* +X142730000Y-121680000D02* +X140750000Y-119700000D01* D50* -X128625000Y-103175000D02* -X128400000Y-103175000D01* -D48* -X132720000Y-119345000D02* -X132250000Y-119345000D01* +X122620000Y-106000000D02* +X122625000Y-105995000D01* +D49* +X145395000Y-121680000D02* +X142730000Y-121680000D01* +X125800000Y-124120000D02* +X126280000Y-124120000D01* +X146448529Y-83500000D02* +X146248528Y-83299999D01* +X145300000Y-104475000D02* +X146175000Y-103600000D01* +X146075000Y-116575000D02* +X146075000Y-112425000D01* +X132925000Y-103600000D02* +X132330000Y-103600000D01* +X138150000Y-110850000D02* +X136500000Y-110850000D01* +X138150000Y-110850000D02* +X138150000Y-112500000D01* +X122625000Y-105100000D02* +X122625000Y-104025000D01* +X129380000Y-103290000D02* +X129380000Y-102438924D01* +X132925000Y-96225000D02* +X132000000Y-95300000D01* +X129500000Y-105500000D02* +X127975000Y-103975000D01* +X123900000Y-83500000D02* +X124100000Y-83700000D01* +X138170000Y-69770000D02* +X139100000Y-70700000D01* +X131800000Y-102670000D02* +X131800000Y-100500000D01* +X134850000Y-112500000D02* +X134850000Y-114150000D01* +X146175000Y-96400000D02* +X146500000Y-96400000D01* +X147300000Y-83500000D02* +X146448529Y-83500000D01* +X141600000Y-105500000D02* +X143500000Y-105500000D01* +X138150000Y-114150000D02* +X139550000Y-114150000D01* +X128100000Y-126400000D02* +X128600000Y-126400000D01* +X143775000Y-105225000D02* +X143500000Y-105500000D01* +X126410000Y-125500552D02* +X127309448Y-126400000D01* +X133595000Y-123105000D02* +X132680000Y-124020000D01* +X134850000Y-110850000D02* +X136500000Y-110850000D01* +X143500000Y-114200000D02* +X142000000Y-114200000D01* +X129500000Y-105500000D02* +X130700000Y-106700000D01* +X123825000Y-96400000D02* +X124600000Y-96400000D01* +X145300000Y-105225000D02* +X145300000Y-104475000D01* +X137500000Y-67200000D02* +X134900000Y-64600000D01* +X138150000Y-112500000D02* +X136500000Y-112500000D01* D50* -X148200000Y-73200000D02* -X147600000Y-73200000D01* -X136600000Y-96100000D02* -X136600000Y-95600000D01* -X145825000Y-96050000D02* -X146175000Y-96400000D01* -X133449999Y-122400000D02* -X133400000Y-122400000D01* -X140675000Y-122275000D02* -X140525000Y-122275000D01* -X123000000Y-83200000D02* -X122700000Y-83500000D01* -X128400000Y-103175000D02* -X127975000Y-103600000D01* -X140400000Y-122400000D02* -X140250000Y-122550000D01* -X123400000Y-95975000D02* -X123825000Y-96400000D01* -X131450000Y-117565000D02* -X131400000Y-117515000D01* -X132449999Y-103850000D02* -X132150000Y-104150000D01* -X145650000Y-96100000D02* -X145650000Y-96000000D01* -X129750000Y-118315000D02* -X129886397Y-118315000D01* -X132449999Y-96100000D02* -X132199999Y-96100000D01* -X123400000Y-103175000D02* +X122920000Y-106300000D02* +X122900000Y-107350000D01* +D49* +X122625000Y-104800000D02* X123825000Y-103600000D01* -X140550000Y-122400000D02* -X140800000Y-122150000D01* -X140250000Y-122550000D02* +X144175000Y-116575000D02* +X143500000Y-115900000D01* +X135900000Y-96400000D02* +X135250000Y-95750000D01* +X128349799Y-95084604D02* +X128349799Y-95470835D01* +X140750000Y-119500000D02* +X140750000Y-118850000D01* +X122700000Y-83500000D02* +X123900000Y-83500000D01* +X141165000Y-124020000D02* X140250000Y-123105000D01* -X123300000Y-103300000D02* -X123050000Y-103050000D01* -X123600000Y-83200000D02* -X123000000Y-83200000D01* -X122650000Y-105400000D02* -X122600000Y-105400000D01* -X121770000Y-115520000D02* -X121750000Y-115500000D01* -X132450000Y-96100000D02* -X132625000Y-96100000D01* -X123000000Y-73200000D02* -X122700000Y-73500000D01* -X145525000Y-103175000D02* -X145750000Y-103175000D01* -X142550000Y-96100000D02* -X142800000Y-95850000D01* -X123000000Y-126250000D02* -X123000000Y-127000000D01* -X148200000Y-83200000D02* -X147600000Y-83200000D01* -X137600000Y-103900000D02* -X137850000Y-104150000D01* -D48* -X131475000Y-108850000D02* -X131475000Y-108325000D01* -D50* -X132199999Y-96100000D02* -X131800000Y-96500000D01* -X133450000Y-122400000D02* -X133750000Y-122700000D01* -X121750000Y-115500000D02* -X121750000Y-114500000D01* -X122850000Y-124900000D02* -X122600000Y-124650000D01* -X128500000Y-103300000D02* -X128750000Y-103050000D01* -X140525000Y-122275000D02* -X140450000Y-122350000D01* -X128230000Y-123780000D02* -X128230000Y-123750000D01* -X136600000Y-95600000D02* -X136300000Y-95300000D01* -X128500000Y-96100000D02* -X128275000Y-96100000D01* -X123300000Y-96100000D02* -X123050000Y-95850000D01* -X142675000Y-103175000D02* -X142450000Y-103175000D01* -X137500000Y-104025000D02* -X137075000Y-103600000D01* -X122750000Y-125900000D02* -X122600000Y-125750000D01* -X137075000Y-96325000D02* -X137075000Y-96400000D01* -X137725000Y-104025000D02* -X137500000Y-104025000D01* -X132300000Y-104000000D02* -X132525000Y-104000000D01* -X123175000Y-103175000D02* -X123400000Y-103175000D01* -X140650000Y-108600000D02* -X140500000Y-108600000D01* -X121750000Y-116295000D02* -X121770000Y-116315000D01* -X122625000Y-105400000D02* -X122900000Y-105675000D01* -X122850000Y-124900000D02* -X123120000Y-125170000D01* -X122750000Y-126000000D02* -X123000000Y-126250000D01* -X148350000Y-73200000D02* -X148500000Y-73050000D01* -X135150000Y-106725000D02* -X135250000Y-106825000D01* -X140400000Y-122400000D02* -X140450000Y-122350000D01* -X131400000Y-117915000D02* -X130800000Y-117915000D01* -X131450000Y-117865000D02* -X131400000Y-117915000D01* -X122750000Y-126100000D02* -X122750000Y-125900000D01* -X134250000Y-106725000D02* -X135150000Y-106725000D01* -X145650000Y-103300000D02* -X145400000Y-103050000D01* -D48* -X125750000Y-118315000D02* -X126750000Y-118315000D01* -D50* -X121770000Y-116515000D02* -X121770000Y-115520000D01* -X131450000Y-117565000D02* -X131450000Y-117865000D01* -D48* -X136650000Y-119215000D02* -X136250000Y-118815000D01* +X127309448Y-126400000D02* +X128100000Y-126400000D01* +X123599999Y-73500000D02* +X124200000Y-72899999D01* +X136500000Y-114150000D02* +X138150000Y-114150000D01* +X134850000Y-114150000D02* +X136500000Y-114150000D01* +X130700000Y-106700000D02* +X130800000Y-106700000D01* +X147300000Y-73500000D02* +X146100000Y-73500000D01* D50* -X132525000Y-104000000D02* -X132925000Y-103600000D01* -X136600000Y-95850000D02* -X137075000Y-96325000D01* -X123600000Y-73200000D02* -X123000000Y-73200000D01* -X130200000Y-119185634D02* -X129870634Y-119615000D01* -D48* -X135150000Y-116815000D02* -X135750000Y-116815000D01* -X131475000Y-108325000D02* -X130950000Y-107800000D01* +X122620000Y-106000000D02* +X122920000Y-106300000D01* +D49* +X134850000Y-110850000D02* +X134850000Y-112500000D01* +X122700000Y-73500000D02* +X123599999Y-73500000D01* +X122625000Y-104025000D02* +X122600000Y-104000000D01* +X133750000Y-123105000D02* +X133595000Y-123105000D01* +X141495000Y-103070000D02* +X142025000Y-103600000D01* +X127975000Y-103975000D02* +X127975000Y-103600000D01* +X145300000Y-105225000D02* +X143775000Y-105225000D01* +X143500000Y-119500000D02* +X143500000Y-105500000D01* +X129380000Y-102438924D02* +X129000000Y-102058924D01* +X129000000Y-100600000D02* +X128700000Y-100300000D01* +X139900000Y-119500000D02* +X140750000Y-119500000D01* +X142025000Y-96400000D02* +X146175000Y-96400000D01* +X122625000Y-105100000D02* +X122625000Y-104800000D01* +X123000000Y-127000000D02* +X123000000Y-125320000D01* D50* -X128275000Y-96100000D02* +X122625000Y-105995000D02* +X122625000Y-105100000D01* +D49* +X146775000Y-120300000D02* +X145395000Y-121680000D01* +X141320000Y-124020000D02* +X141165000Y-124020000D01* +X140600000Y-101120000D02* +X140600000Y-100500000D01* +X140750000Y-118850000D02* +X140600000Y-118700000D01* +X131570000Y-102840000D02* +X131600000Y-102870000D01* +X128349799Y-95470835D02* +X127975000Y-95845634D01* +X127975000Y-95845634D02* X127975000Y-96400000D01* -X123120000Y-125170000D02* +X122500000Y-125200000D02* X123120000Y-125200000D01* -X132260000Y-119345000D02* -X132250000Y-119355000D01* -X147600000Y-83200000D02* -X147300000Y-83500000D01* -X130200000Y-118628603D02* -X130200000Y-119185634D01* -X130150000Y-126050000D02* -X130400000Y-126300000D01* -X130200000Y-118001397D02* -X130200000Y-117244366D01* -X142450000Y-103175000D02* +X137075000Y-96400000D02* +X135900000Y-96400000D01* +X126280000Y-124120000D02* +X126900000Y-123500000D01* +X140600000Y-100500000D02* +X140400000Y-100300000D01* +X136500000Y-114150000D02* +X136500000Y-112500000D01* +X138150000Y-114150000D02* +X138150000Y-112500000D01* +X146175000Y-103600000D02* X142025000Y-103600000D01* -X132625000Y-96100000D02* -X132925000Y-96400000D01* -X133750000Y-122700000D02* -X133750000Y-123105000D01* -X133449999Y-122400000D02* -X133199999Y-122150000D01* -X128550000Y-96100000D02* -X129000000Y-96550000D01* -X147600000Y-73200000D02* -X147300000Y-73500000D01* -X148350000Y-83200000D02* -X148500000Y-83050000D01* -X145650000Y-96050000D02* -X145825000Y-96050000D01* -X123600000Y-73200000D02* -X123950000Y-73200000D01* -X131400000Y-117515000D02* -X130800000Y-117515000D01* -X130150000Y-126050000D02* -X129650000Y-125550000D01* -X142450000Y-95975000D02* -X142025000Y-96400000D01* -X122850000Y-119315000D02* -X121750000Y-119315000D01* -X122900000Y-105675000D02* -X122900000Y-106125000D01* -D48* -X133000000Y-119265000D02* -X132720000Y-119345000D01* -D50* -X128500000Y-96100000D02* -X128550000Y-96100000D01* -X129886397Y-118315000D02* -X130200000Y-118628603D01* -D48* -X135750000Y-116815000D02* -X136250000Y-117315000D01* -D50* -X121770000Y-119295000D02* -X121750000Y-119315000D01* -X142675000Y-95975000D02* -X142450000Y-95975000D01* -X121770000Y-116515000D02* -X121770000Y-119295000D01* -X148200000Y-73200000D02* -X148350000Y-73200000D01* -D48* -X139000000Y-114300000D02* -X137450000Y-114300000D01* -D50* -X128500000Y-124050000D02* -X128750000Y-124300000D01* -X128500000Y-124050000D02* -X128230000Y-123780000D01* -X145750000Y-103175000D02* -X146175000Y-103600000D01* -X129886397Y-118315000D02* -X130200000Y-118001397D01* -X130200000Y-117244366D02* -X129770634Y-116815000D01* +X129000000Y-102058924D02* +X129000000Y-100600000D01* +X124200000Y-72899999D02* +X124200000Y-71800000D01* +X132925000Y-96400000D02* +X132925000Y-96225000D01* +X128600000Y-126400000D02* +X129650000Y-125350000D01* +X137675000Y-103000000D02* +X137075000Y-103600000D01* +X139550000Y-114150000D02* +X139600000Y-114100000D01* +X140750000Y-119700000D02* +X140750000Y-119500000D01* +X130000000Y-103910000D02* +X129380000Y-103290000D01* %TO.N,/Buttons_Direct/BTN_MACRO4*% -X127975000Y-100788600D02* -X126979600Y-99793200D01* +X130200000Y-104800000D02* +X130200000Y-104950000D01* +X128600000Y-102975000D02* +X128800000Y-102975000D01* +X128800000Y-102975000D02* +X128800000Y-104234314D01* X127975000Y-101450000D02* -X127975000Y-101125000D01* +X128600000Y-102075000D01* +X128600000Y-102075000D02* +X128600000Y-102975000D01* +X129365686Y-104800000D02* +X130200000Y-104800000D01* +X128800000Y-104234314D02* +X129365686Y-104800000D01* X123825000Y-101450000D02* -X124651700Y-101450000D01* -X129800000Y-100700000D02* -X128050000Y-100700000D01* -X127975000Y-101125000D02* -X127975000Y-100788600D01* -X126979600Y-99793200D02* -X126308500Y-99793200D01* -X126308500Y-99793200D02* -X124651700Y-101450000D01* -%TO.N,VBUS*% -D49* -X125770000Y-119275000D02* -X125770000Y-125525300D01* -D50* -X124790000Y-119275000D02* -X124750000Y-119315000D01* -D49* -X139450000Y-119472500D02* -X139450000Y-121868900D01* -D50* -X126910000Y-119115000D02* -X126750000Y-119275000D01* -D49* -X149218700Y-109703800D02* -X139450000Y-119472500D01* -X149218700Y-96601800D02* -X149218700Y-109703800D01* -D50* -X128700000Y-119115000D02* -X126910000Y-119115000D01* -D49* -X134550000Y-121802500D02* -X134550000Y-123105000D01* -D48* -X126750000Y-119275000D02* -X124790000Y-119275000D01* -D49* -X139450000Y-123105000D02* -X139450000Y-121868900D01* -X134650000Y-121702500D02* -X134550000Y-121802500D01* -%TO.N,3V3*% -D50* -X127850000Y-128650000D02* -X129098300Y-127401700D01* -X123900000Y-107406100D02* -X123900000Y-113658400D01* -X130981500Y-123372500D02* -X128594000Y-120985000D01* -D48* -X124260000Y-117315000D02* -X124650000Y-117315000D01* -D51* -X132425000Y-109800000D02* -X131475000Y-110750000D01* -D50* -X134860000Y-114515000D02* -X132645000Y-112300000D01* -X131415800Y-125415900D02* -X130981500Y-124981600D01* -X131415800Y-126713000D02* -X131415800Y-125415900D01* -D51* -X131475000Y-110750000D02* -X131475000Y-111825000D01* -X132950000Y-108035000D02* -X131975000Y-107060000D01* -D50* -X127047700Y-123972300D02* -X127270000Y-123750000D01* -X127850000Y-128650000D02* -X127047700Y-127847700D01* -X128381250Y-121170000D02* -X127300000Y-121550001D01* -D51* -X132950000Y-109800000D02* -X132425000Y-109800000D01* -D48* -X124260000Y-117315000D02* -X123860000Y-116915000D01* -D50* -X132645000Y-112300000D02* -X131950000Y-112300000D01* -X129098300Y-127401700D02* -X130727100Y-127401700D01* -X123900000Y-106125000D02* -X123900000Y-107406100D01* -X130981500Y-124981600D02* -X130981500Y-123372500D01* -X130727100Y-127401700D02* -X131415800Y-126713000D01* -X127047700Y-127847700D02* -X127047700Y-123972300D01* -D51* -X134450000Y-109800000D02* -X132950000Y-109800000D01* -D50* -X128381250Y-120800001D02* -X128381250Y-121170000D01* -X124549200Y-107406100D02* -X123900000Y-107406100D01* -X128594000Y-120985000D02* -X128381000Y-120985000D01* -D51* -X132950000Y-109800000D02* -X132950000Y-108035000D01* -X131475000Y-111825000D02* -X131950000Y-112300000D01* +X127975000Y-101450000D01* +X130200000Y-104950000D02* +X130550000Y-105300000D01* +X130550000Y-105300000D02* +X130550000Y-105500000D01* +%TO.N,/MCU_Core/MCU_EN*% +X145225000Y-120300000D02* +X145225000Y-118865000D01* +X142650000Y-120300000D02* +X142450000Y-120100000D01* +X145225000Y-120300000D02* +X142650000Y-120300000D01* +X142450000Y-120100000D02* +X142450000Y-119500000D01* +X145225000Y-118865000D02* +X145490000Y-118600000D01* +%TO.N,/MCU_Core/MCU_BOOT*% +X148225000Y-112315000D02* +X148225000Y-112425000D01* +X144900000Y-108300000D02* +X145000000Y-108400000D01* +X145000000Y-109090000D02* +X148225000Y-112315000D01* +X139900000Y-106400000D02* +X139900000Y-105500000D01* +X148225000Y-116575000D02* +X148225000Y-112425000D01* +X145000000Y-108400000D02* +X145000000Y-109090000D01* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X130600000Y-101668529D02* +X130990000Y-102058529D01* +X130549998Y-93079364D02* +X130549998Y-95829896D01* +X130400000Y-96067155D02* +X130400000Y-97026471D01* +X130400000Y-99551471D02* +X130600000Y-99751471D01* +X130600000Y-101448529D02* +X130600000Y-101668529D01* +X130600000Y-99751471D02* +X130600000Y-100751471D01* +X130593628Y-95873527D02* +X130400000Y-96067155D01* +X132250000Y-105500000D02* +X132250000Y-104480000D01* +X130990000Y-102058529D02* +X130990000Y-103220000D01* +X130549998Y-95829896D02* +X130593628Y-95873527D01* +X130250000Y-97673529D02* +X130400000Y-97823529D01* +X130990000Y-103220000D02* +X131600000Y-103830000D01* +X130500000Y-101348529D02* +X130600000Y-101448529D01* +X130500000Y-100851471D02* +X130500000Y-101348529D01* +X130400000Y-97823529D02* +X130400000Y-99551471D01* +X130400000Y-97026471D02* +X130250000Y-97176471D01* +X130600000Y-100751471D02* +X130500000Y-100851471D01* +X130070634Y-92600000D02* +X130549998Y-93079364D01* +X132250000Y-104480000D02* +X131600000Y-103830000D01* +X130250000Y-97176471D02* +X130250000Y-97673529D01* %TO.N,/Buttons_Direct/BTN_MACRO2*% -D50* +X133750000Y-96598529D02* +X133750000Y-95075000D01* +X133750000Y-95075000D02* +X132925000Y-94250000D01* +X135650000Y-105500000D02* +X135650000Y-102040686D01* +X134800000Y-97648529D02* +X133750000Y-96598529D01* X137075000Y-94250000D02* X132925000Y-94250000D01* -X132098300Y-94817800D02* -X132098300Y-94250000D01* -X131797000Y-95119100D02* -X132098300Y-94817800D01* -X132925000Y-94250000D02* -X132098300Y-94250000D01* +X135650000Y-102040686D02* +X134800000Y-101190686D01* +X134800000Y-101190686D02* +X134800000Y-97648529D01* +%TO.N,/MCU_Core/USB_DM*% +X136250000Y-123105000D02* +X136250000Y-123862410D01* +X136250000Y-123862410D02* +X136687590Y-124300000D01* +X127750000Y-115250000D02* +X128020000Y-114970000D01* +X136250000Y-123105000D02* +X136250000Y-122281905D01* +X135648095Y-121680000D02* +X130654314Y-121680000D01* +X124600000Y-115250000D02* +X127750000Y-115250000D01* +X130654314Y-121680000D02* +X130634315Y-121700000D01* +X130634315Y-121700000D02* +X126400000Y-121700000D01* +X124600000Y-119900000D02* +X124600000Y-115250000D01* +X137250000Y-123862410D02* +X137250000Y-123105000D01* +X136687590Y-124300000D02* +X136812410Y-124300000D01* +X136250000Y-122281905D02* +X135648095Y-121680000D01* +X136812410Y-124300000D02* +X137250000Y-123862410D01* +X126400000Y-121700000D02* +X124600000Y-119900000D01* +%TO.N,/MCU_Core/USB_DM_MCU*% +X128100000Y-112500000D02* +X128100000Y-113980000D01* +X129500000Y-112500000D02* +X128100000Y-112500000D01* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X121461600Y-73804500D02* -X121461600Y-73127900D01* -X122175200Y-72799800D02* -X122700000Y-72275000D01* -X122382100Y-74725000D02* -X121461600Y-73804500D01* -X124754600Y-76779600D02* -X122700000Y-74725000D01* +X121800000Y-74725000D02* +X121300000Y-74225000D01* +X124700000Y-84422057D02* +X124700000Y-76725000D01* +X121873930Y-107063387D02* +X121810543Y-107000000D01* +X120800000Y-97734315D02* +X120800000Y-88322057D01* +X121300000Y-74225000D02* +X121300000Y-73300000D01* +X120800000Y-88322057D02* +X124700000Y-84422057D01* +X121300000Y-107000000D02* +X120900000Y-106600000D01* X122700000Y-74725000D02* -X122382100Y-74725000D01* -X121461600Y-73127900D02* -X121789700Y-72799800D01* -X124754600Y-83434100D02* -X124754600Y-76779600D01* -X121789700Y-72799800D02* -X122175200Y-72799800D01* +X121800000Y-74725000D01* +X124700000Y-76725000D02* +X122700000Y-74725000D01* +X129650000Y-116600000D02* +X129500000Y-116750000D01* +X120900000Y-106600000D02* +X120900000Y-97834315D01* +X121300000Y-73300000D02* +X122325000Y-72275000D01* +X130300000Y-116600000D02* +X129650000Y-116600000D01* +X120900000Y-97834315D02* +X120800000Y-97734315D01* +X121810543Y-107000000D02* +X121300000Y-107000000D01* +X122325000Y-72275000D02* +X122700000Y-72275000D01* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X140475000Y-101450000D02* -X139209300Y-100184300D01* -X142025000Y-101450000D02* -X140475000Y-101450000D01* -X146175000Y-101450000D02* +X142600000Y-102400000D02* +X142600000Y-102025000D01* +X140900000Y-107000000D02* +X141300000Y-106600000D01* +X142600000Y-102025000D02* X142025000Y-101450000D01* +X138851471Y-107000000D02* +X140900000Y-107000000D01* +X138200000Y-106348529D02* +X138851471Y-107000000D01* +X138200000Y-105500000D02* +X138200000Y-106348529D01* +X142025000Y-101450000D02* +X146175000Y-101450000D01* %TO.N,/Buttons_Direct/BTN_MACRO3*% -X141198300Y-94250000D02* -X141198300Y-97034600D01* -X142212500Y-94250000D02* -X142851700Y-94250000D01* -X141198300Y-97034600D02* -X139789800Y-98443100D01* -X142112400Y-94250000D02* -X142199800Y-94250000D01* -X142112400Y-94250000D02* +X135300000Y-101125000D02* +X135300000Y-98751471D01* +X138150000Y-94250000D02* X142025000Y-94250000D01* -X144981300Y-93883000D02* -X143218700Y-93883000D01* -X145348300Y-94250000D02* -X144981300Y-93883000D01* -X142212500Y-94250000D02* -X142199800Y-94250000D01* -X143218700Y-93883000D02* -X142851700Y-94250000D01* -X146175000Y-94250000D02* -X145348300Y-94250000D01* +X136500000Y-105500000D02* +X136250000Y-105250000D01* +X136250000Y-105250000D02* +X136250000Y-102075000D01* X142025000Y-94250000D02* -X141198300Y-94250000D01* +X146175000Y-94250000D01* +X136250000Y-102075000D02* +X135300000Y-101125000D01* +X138100000Y-97025000D02* +X138100000Y-94300000D01* +X137026471Y-97025000D02* +X138100000Y-97025000D01* +X138100000Y-94300000D02* +X138150000Y-94250000D01* +X135300000Y-98751471D02* +X137026471Y-97025000D01* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X127975000Y-94250000D02* -X127148300Y-94250000D01* -X127120000Y-94278300D02* -X127148300Y-94250000D01* +X122600000Y-103400000D02* +X121700000Y-103400000D01* X123825000Y-94250000D02* -X124651700Y-94250000D01* -X128801700Y-94250000D02* -X128910500Y-94250000D01* -X128910500Y-94250000D02* -X129065000Y-94095500D01* -X124651700Y-94250000D02* -X124680000Y-94278300D01* -X124680000Y-94278300D02* -X127120000Y-94278300D01* -X127975000Y-94250000D02* -X128801700Y-94250000D01* +X127975000Y-94250000D01* +X123025000Y-102975000D02* +X122600000Y-103400000D01* +X121700000Y-103400000D02* +X121700000Y-98325000D01* +X123000000Y-95075000D02* +X123825000Y-94250000D01* +X126774998Y-104025000D02* +X125700000Y-104025000D01* +X123000000Y-97025000D02* +X123000000Y-95075000D01* +X121700000Y-98325000D02* +X123000000Y-97025000D01* +X124650000Y-102975000D02* +X123025000Y-102975000D01* +X125700000Y-104025000D02* +X124650000Y-102975000D01* +X129550000Y-109900000D02* +X129500000Y-109950000D01* +X130400000Y-109900000D02* +X129550000Y-109900000D01* +X128200000Y-105450002D02* +X126774998Y-104025000D01* %TO.N,/RGB_LED/RGB_DIN_R*% -X131014100Y-126546700D02* -X131014100Y-125890900D01* -X127875300Y-121964700D02* -X127240000Y-122600000D01* X127850000Y-125350000D02* -X129500000Y-127000000D01* -X131014100Y-125890900D02* -X130538500Y-125415300D01* -X130538500Y-123513800D02* -X128989400Y-121964700D01* -X130560800Y-127000000D02* -X131014100Y-126546700D01* -X130538500Y-125415300D02* -X130538500Y-123513800D01* -X129500000Y-127000000D02* -X130560800Y-127000000D01* -X128989400Y-121964700D02* -X127875300Y-121964700D01* -%TO.N,VBAT*% -D48* -X133250000Y-117540000D02* -X132075000Y-118715000D01* -D50* -X132075000Y-118715000D02* -X130800000Y-118715000D01* -D48* -X133250000Y-116815000D02* -X133250000Y-117540000D01* -D49* -X133717800Y-118937400D02* -X133810600Y-118937400D01* -X132785200Y-118004800D02* -X133717800Y-118937400D01* -%TO.N,/MCU_Core/STAT2*% -D50* -X129844800Y-112901800D02* -X129844800Y-103356900D01* -X132450000Y-117430686D02* -X132450000Y-115905000D01* -X130473100Y-96585600D02* -X130387500Y-96500000D01* -X131565686Y-118315000D02* -X132450000Y-117430686D01* -X132450000Y-115905000D02* -X133840000Y-114515000D01* -X130800000Y-118315000D02* -X131565686Y-118315000D01* -X130473100Y-102728600D02* -X130473100Y-96585600D01* -X129844800Y-103356900D02* -X130473100Y-102728600D01* -X132649000Y-115706000D02* -X129844800Y-112901800D01* -%TO.N,/Power_Charger/CHG_TS*% -X126435000Y-114500000D02* -X122770000Y-114500000D01* -X128700000Y-116765000D02* -X128700000Y-117515000D01* -X128700000Y-116765000D02* -X126435000Y-114500000D01* -%TO.N,/Power_Charger/CHG_VSET*% -X127184314Y-115815000D02* -X127750000Y-116380686D01* -X127750000Y-116380686D02* -X127750000Y-116419756D01* -X122770000Y-115500000D02* -X122805000Y-115465000D01* -X128250000Y-117219756D02* -X128150000Y-117319756D01* -X126750000Y-115815000D02* -X127184314Y-115815000D01* -X126400000Y-115465000D02* -X126750000Y-115815000D01* -X128354756Y-117915000D02* -X128700000Y-117915000D01* -X127750000Y-116419756D02* -X128250000Y-116919756D01* -X122805000Y-115465000D02* -X126400000Y-115465000D01* -X128250000Y-116919756D02* -X128250000Y-117219756D01* -X128150000Y-117319756D02* -X128150000Y-117710244D01* -X128150000Y-117710244D02* -X128354756Y-117915000D01* -%TO.N,/Power_Charger/CHG_ISET*% -X127750000Y-117875930D02* -X128189071Y-118315000D01* -X127350000Y-116546372D02* -X127350000Y-116585442D01* -X126098529Y-116315000D02* -X127118628Y-116315000D01* -X127750000Y-116985442D02* -X127750000Y-117875930D01* -X125748529Y-116665000D02* -X126098529Y-116315000D01* -X127350000Y-116585442D02* -X127750000Y-116985442D01* -X128189071Y-118315000D02* -X128700000Y-118315000D01* -X127118628Y-116315000D02* -X127350000Y-116546372D01* -X122990000Y-116315000D02* -X122790000Y-116515000D01* -X125251471Y-116665000D02* -X125748529Y-116665000D01* -X124901471Y-116315000D02* -X122990000Y-116315000D01* -X124901471Y-116315000D02* -X125251471Y-116665000D01* -%TO.N,/MCU_Core/STAT1*% -X123825735Y-117590735D02* -X124325000Y-118090000D01* -X124325000Y-118090000D02* -X124895000Y-118090000D01* -X128023386Y-118715000D02* -X127350000Y-118041615D01* -X123374265Y-117590735D02* -X123825735Y-117590735D01* -X128700000Y-118715000D02* -X128023386Y-118715000D01* -X125670000Y-117315000D02* -X124895000Y-118090000D01* -X125670000Y-117315000D02* -X126770000Y-117315000D01* -X127350000Y-117895000D02* -X126770000Y-117315000D01* -X127350000Y-118041615D02* -X127350000Y-117895000D01* +X127850000Y-123550000D01* +X127850000Y-123550000D02* +X127900000Y-123500000D01* %TO.N,/Accelerometer/I2C_SDA*% -X127334600Y-75008600D02* -X127094200Y-74768200D01* -X132254800Y-67212500D02* -X132254800Y-65652100D01* -X127094200Y-74768200D02* -X127094200Y-72373100D01* -X127334600Y-81692500D02* -X127334600Y-75008600D01* -X127094200Y-72373100D02* -X132254800Y-67212500D01* -X126436300Y-89149100D02* -X126436300Y-82590800D01* -X122424400Y-93161000D02* -X126436300Y-89149100D01* -X123299500Y-102251500D02* -X122424400Y-101376400D01* -X124900000Y-106125000D02* -X124900000Y-104808600D01* -X124900000Y-104808600D02* -X124959600Y-104749000D01* -X123798900Y-102251500D02* -X123299500Y-102251500D01* -X124959600Y-103412200D02* -X123798900Y-102251500D01* -X124959600Y-104749000D02* -X124959600Y-103412200D01* -X122424400Y-101376400D02* -X122424400Y-93161000D01* -X126436300Y-82590800D02* -X127334600Y-81692500D01* +X121550000Y-116098529D02* +X124200000Y-113448529D01* +X121874741Y-124680758D02* +X121550000Y-124356017D01* +X126000000Y-105800000D02* +X125500000Y-106300000D01* +X129500000Y-106550000D02* +X128298924Y-106550000D01* +X124200000Y-113448529D02* +X124200000Y-111600000D01* +X124900000Y-106900000D02* +X124900000Y-108125000D01* +X121550000Y-124356017D02* +X121550000Y-116098529D01* +X124600000Y-109800000D02* +X124600000Y-108425000D01* +X124600000Y-108425000D02* +X124900000Y-108125000D01* +X127548924Y-105800000D02* +X126000000Y-105800000D01* +X125500000Y-106300000D02* +X124900000Y-106900000D01* +X128298924Y-106550000D02* +X127548924Y-105800000D01* %TO.N,/Accelerometer/I2C_SCL*% -X125900000Y-101235300D02* -X126735300Y-100400000D01* -X126003900Y-88872200D02* -X126003900Y-70995100D01* -X121327800Y-93548300D02* -X126003900Y-88872200D01* -X121327800Y-96462500D02* -X121327800Y-93548300D01* -X125900000Y-106125000D02* -X125900000Y-101235300D01* -%TO.N,/Power_Buck/BUCK_FB*% -X133230000Y-106670000D02* -X133500000Y-106400000D01* -X135450000Y-106250000D02* -X135400000Y-106200000D01* -X142450000Y-110600000D02* -X142500000Y-110550000D01* -X140950000Y-108200000D02* -X140800000Y-108050000D01* -X135600000Y-106300000D02* -X135550000Y-106300000D01* -D48* -X132655000Y-106150000D02* -X133230000Y-106725000D01* -D50* -X141650000Y-111450000D02* -X142450000Y-110650000D01* -X143450000Y-109000000D02* -X143450000Y-108550000D01* -X139450000Y-107950000D02* -X138750000Y-107250000D01* -X143050000Y-108250000D02* -X143000000Y-108200000D01* -X133230000Y-106725000D02* -X133230000Y-106670000D01* -X141875000Y-111225000D02* -X141875000Y-112075000D01* -X136550000Y-107250000D02* -X135600000Y-106300000D01* -X143450000Y-108550000D02* -X143150000Y-108250000D01* -X135500000Y-106250000D02* -X135450000Y-106250000D01* -X143400000Y-109050000D02* -X143450000Y-109000000D01* -X143150000Y-108250000D02* -X143050000Y-108250000D01* -X140550000Y-108000000D02* -X140500000Y-107950000D01* -X134650000Y-106100000D02* -X133800000Y-106100000D01* -X140750000Y-108050000D02* -X140700000Y-108000000D01* -X135400000Y-106200000D02* -X134750000Y-106200000D01* -X134750000Y-106200000D02* -X134650000Y-106100000D01* -X140800000Y-108050000D02* -X140750000Y-108050000D01* -D48* -X131975000Y-106040000D02* -X132655000Y-106040000D01* -D50* -X142500000Y-110550000D02* -X142500000Y-110000000D01* -X143000000Y-108200000D02* -X140950000Y-108200000D01* -X133800000Y-106100000D02* -X133500000Y-106400000D01* -X142500000Y-110000000D02* -X143400000Y-109100000D01* -X138750000Y-107250000D02* -X136550000Y-107250000D01* -X143400000Y-109100000D02* -X143400000Y-109050000D01* -X142450000Y-110650000D02* -X142450000Y-110600000D01* -X140500000Y-107950000D02* -X139450000Y-107950000D01* -X140700000Y-108000000D02* -X140550000Y-108000000D01* -X135550000Y-106300000D02* -X135500000Y-106250000D01* -D48* -X132655000Y-106040000D02* -X132655000Y-106150000D01* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -D50* -X146179200Y-84394700D02* -X145804700Y-84769200D01* -X146509400Y-84725000D02* -X147300000Y-84725000D01* -X146092600Y-83157900D02* -X146092600Y-84308200D01* -X146092600Y-84308200D02* -X146179200Y-84394700D01* -X147300000Y-82275000D02* -X146975500Y-82275000D01* -X146975500Y-82275000D02* -X146092600Y-83157900D01* -X146179200Y-84394700D02* -X146509400Y-84725000D01* -%TO.N,/USB_C/USB_CC1*% -X135750000Y-123105000D02* -X135750000Y-121500900D01* -%TO.N,/MCU_Core/USB_DP*% -X136750000Y-123935500D02* -X136998700Y-124184200D01* -X136798300Y-124384600D02* -X136798300Y-126076800D01* -X143466900Y-119673900D02* -X148072200Y-115068600D01* -X137446300Y-124184200D02* -X136998700Y-124184200D01* -X148072200Y-115068600D02* -X148072200Y-111842500D01* -X137750000Y-123880500D02* -X137446300Y-124184200D01* -X136750000Y-123105000D02* -X136750000Y-123935500D01* -X140381100Y-126716200D02* -X143466900Y-123630400D01* -X137437700Y-126716200D02* -X140381100Y-126716200D01* -X143466900Y-123630400D02* -X143466900Y-119673900D01* -X136998700Y-124184200D02* -X136798300Y-124384600D01* -X137750000Y-123105000D02* -X137750000Y-123880500D01* -X136798300Y-126076800D02* -X137437700Y-126716200D01* -%TO.N,/MCU_Core/USB_DM*% -X136977500Y-122057300D02* -X137452700Y-121582100D01* -X137901700Y-101286100D02* -X137901700Y-95241600D01* -X136977500Y-122057300D02* -X136457100Y-122057300D01* -X137452700Y-120468300D02* -X143879600Y-114041400D01* -X141199800Y-104584200D02* -X137901700Y-101286100D01* -X141199800Y-105730600D02* -X141199800Y-104584200D01* -X136457100Y-122057300D02* -X136250000Y-122264400D01* -X143879600Y-108410400D02* -X141199800Y-105730600D01* -X137250000Y-122329800D02* -X136977500Y-122057300D01* -X137250000Y-123105000D02* -X137250000Y-122329800D01* -X143879600Y-114041400D02* -X143879600Y-108410400D01* -X137452700Y-121582100D02* -X137452700Y-120468300D01* -X136250000Y-122264400D02* -X136250000Y-123105000D01* -%TO.N,/USB_C/USB_CC2*% -X138750000Y-123105000D02* -X138750000Y-126065000D01* +X125800000Y-108225000D02* +X125900000Y-108125000D01* +X121100000Y-115700000D02* +X122700000Y-114100000D01* +X126615000Y-107410000D02* +X125900000Y-108125000D01* +X127200000Y-107410000D02* +X126615000Y-107410000D01* +X121100000Y-124880210D02* +X121100000Y-115700000D01* +X127210000Y-107400000D02* +X127200000Y-107410000D01* +X129500000Y-107400000D02* +X127210000Y-107400000D01* +X125800000Y-109700000D02* +X125800000Y-108225000D01* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X139050000Y-106050000D02* +X138900000Y-106200000D01* +X139050000Y-105500000D02* +X139050000Y-106050000D01* +%TO.N,/MCU_Core/STICK_Y*% +X131400000Y-93051471D02* +X133948529Y-93051471D01* +X139675000Y-83659745D02* +X139200000Y-83184745D01* +X141700000Y-90798529D02* +X141700000Y-86425000D01* +X141984745Y-78500000D02* +X143730000Y-78500000D01* +X139200000Y-83184745D02* +X139200000Y-81284745D01* +X135100000Y-91900000D02* +X140598529Y-91900000D01* +X131350000Y-95498529D02* +X131350000Y-93101471D01* +X131350000Y-93101471D02* +X131400000Y-93051471D01* +X134800000Y-105500000D02* +X134800000Y-104300000D01* +X133948529Y-93051471D02* +X135100000Y-91900000D01* +X141700000Y-86425000D02* +X139675000Y-84400000D01* +X140598529Y-91900000D02* +X141700000Y-90798529D01* +X134400000Y-103900000D02* +X134400000Y-99535785D01* +X134400000Y-99535785D02* +X131500000Y-96635785D01* +X131500000Y-96635785D02* +X131500000Y-95648529D01* +X134800000Y-104300000D02* +X134400000Y-103900000D01* +X131500000Y-95648529D02* +X131350000Y-95498529D01* +X139675000Y-84400000D02* +X139675000Y-83659745D01* +X139200000Y-81284745D02* +X141984745Y-78500000D01* %TO.N,/MCU_Core/STICK_X*% -X132385200Y-78073900D02* -X132385200Y-76736800D01* -X130268800Y-90630500D02* -X130268800Y-80190300D01* -X130268800Y-80190300D02* -X132385200Y-78073900D01* -X127222700Y-93676600D02* -X130268800Y-90630500D01* -X126670100Y-93676600D02* -X127222700Y-93676600D01* -X135000000Y-74122000D02* +X131000000Y-92734314D02* +X133500000Y-90234314D01* +X131000000Y-95714215D02* +X130950000Y-95664214D01* +X134000000Y-105199999D02* +X134000000Y-99701471D01* +X133500000Y-80626471D02* +X133500000Y-72573529D01* +X133500000Y-81253529D02* +X133435000Y-81188529D01* +X133949999Y-105250000D02* +X134000000Y-105199999D01* +X130950000Y-92935785D02* +X131000000Y-92885786D01* +X131000000Y-96701470D02* +X131000000Y-95714215D01* +X133500000Y-72573529D02* +X135000000Y-71073529D01* +X133949999Y-105500000D02* +X133949999Y-105250000D01* +X135000000Y-71073529D02* X135000000Y-69770000D01* -X132385200Y-76736800D02* -X135000000Y-74122000D01* -%TO.N,/MCU_Core/STICK_Y*% -X132471100Y-90895600D02* -X132471100Y-92108500D01* -X143730000Y-78500000D02* -X141910600Y-78500000D01* -X141910600Y-78500000D02* -X136768600Y-83642000D01* -X130057700Y-95460000D02* -X130207300Y-95609600D01* -X130057700Y-94521900D02* -X130057700Y-95460000D01* -X132471100Y-92108500D02* -X130057700Y-94521900D01* -X136768600Y-83642000D02* -X136768600Y-86598100D01* -X136768600Y-86598100D02* -X132471100Y-90895600D01* +X131000000Y-92885786D02* +X131000000Y-92734314D01* +X134000000Y-99701471D02* +X131000000Y-96701470D01* +X133500000Y-90234314D02* +X133500000Y-81253529D01* +X133435000Y-81188529D02* +X133435000Y-80691471D01* +X130950000Y-95664214D02* +X130950000Y-92935785D01* +X133435000Y-80691471D02* +X133500000Y-80626471D01* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X136161765Y-101138235D02* +X136763235Y-101138235D01* +X136763235Y-101138235D02* +X137075000Y-101450000D01* +X133300000Y-100800000D02* +X133300000Y-101075000D01* +X133100000Y-105500000D02* +X133100000Y-107000000D01* +X133300000Y-101075000D02* +X132925000Y-101450000D01* +X133100000Y-105300000D02* +X133100000Y-105500000D01* +%TO.N,/MCU_Core/VSYS_SENSE*% +X131400000Y-105300000D02* +X130700000Y-104600000D01* +X131400000Y-105500000D02* +X131400000Y-105300000D01* +X130000000Y-102890000D02* +X130000000Y-102120000D01* +X130700000Y-103590000D02* +X130000000Y-102890000D01* +X130000000Y-102120000D02* +X129800000Y-101920000D01* +X130700000Y-104600000D02* +X130700000Y-103590000D01* +%TO.N,/MCU_Core/STAT2*% +X129674265Y-108075735D02* +X129500000Y-108250000D01* +X130824265Y-108075735D02* +X129674265Y-108075735D01* +%TO.N,/MCU_Core/STAT1*% +X130600000Y-109100000D02* +X130800000Y-108900000D01* +X129500000Y-109100000D02* +X130600000Y-109100000D01* +X126150000Y-97470100D02* +X126150000Y-97650000D01* +X126150000Y-97650000D02* +X127500000Y-99000000D01* +%TO.N,/MCU_Core/BTN_STICK*% +X129100000Y-94350000D02* +X129200000Y-94450000D01* +X126969163Y-100400000D02* +X126600000Y-100400000D01* +X128734582Y-98634582D02* +X126969163Y-100400000D01* +X130500000Y-110800000D02* +X129500000Y-110800000D01* +X131750000Y-84250000D02* +X129100000Y-86900000D01* +X129100000Y-86900000D02* +X129100000Y-94350000D01* +X129200000Y-94450000D02* +X129200000Y-98169164D01* +X129200000Y-98169164D02* +X128734582Y-98634582D01* +%TO.N,/Buttons_Direct/BTN_THR_DN*% +X120500000Y-98000001D02* +X120500000Y-108600000D01* +X120500000Y-108600000D02* +X122700000Y-110800000D01* +X122325000Y-82275000D02* +X122700000Y-82275000D01* +X128450000Y-110800000D02* +X129300000Y-111650000D01* +X121100000Y-83500000D02* +X122325000Y-82275000D01* +X122700000Y-85856371D02* +X120400000Y-88156371D01* +X120400000Y-88156371D02* +X120400000Y-97900001D01* +X129300000Y-111650000D02* +X129500000Y-111650000D01* +X122700000Y-110800000D02* +X128450000Y-110800000D01* +X120400000Y-97900001D02* +X120500000Y-98000001D01* +X122700000Y-84725000D02* +X122700000Y-85856371D01* +X122325000Y-84725000D02* +X122700000Y-84725000D01* +X121100000Y-83500000D02* +X122325000Y-84725000D01* +%TO.N,/MCU_Core/USB_DP_MCU*% +X128479999Y-115920000D02* +X128100000Y-115920000D01* +X128800000Y-113350000D02* +X128800000Y-115600000D01* +X129500000Y-113350000D02* +X128800000Y-113350000D01* +X128800000Y-115600000D02* +X128479999Y-115920000D01* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X123396100Y-128212300D02* -X122599600Y-128212300D01* -X120688600Y-125913600D02* -X120688600Y-97070100D01* -X121775000Y-127000000D02* -X120688600Y-125913600D01* +X121775000Y-127900000D02* +X121775000Y-127000000D01* X124225000Y-125345000D02* X124080000Y-125200000D01* +X124400000Y-120265685D02* +X124400000Y-120400000D01* +X124400000Y-120400000D02* +X126200000Y-122200000D01* +X123925000Y-128200000D02* +X122075000Y-128200000D01* +X124480000Y-124420000D02* +X124480000Y-124800000D01* +X124200000Y-120065686D02* +X124400000Y-120265685D01* X124225000Y-127000000D02* -X124225000Y-125345000D01* -X124225000Y-127383400D02* -X123396100Y-128212300D01* -X122599600Y-128212300D02* -X122102600Y-127715300D01* -X122102600Y-127327600D02* +X124225000Y-127900000D01* +X121056239Y-126281239D02* X121775000Y-127000000D01* +X124800000Y-123600000D02* +X124800000Y-124100000D01* +X124000000Y-119600000D02* +X124200000Y-119800000D01* +X124225000Y-127900000D02* +X123925000Y-128200000D01* +X122075000Y-128200000D02* +X121775000Y-127900000D01* +X126200000Y-122200000D02* +X124800000Y-123600000D01* +X120600000Y-125765642D02* +X121056239Y-126221881D01* X124225000Y-127000000D02* -X124225000Y-127383400D01* -X122102600Y-127715300D02* -X122102600Y-127327600D01* +X124225000Y-125345000D01* +X124480000Y-124800000D02* +X124080000Y-125200000D01* +X124800000Y-124100000D02* +X124480000Y-124420000D01* +X129500000Y-114200000D02* +X130500000Y-114200000D01* +X121056239Y-126221881D02* +X121056239Y-126281239D01* +X124200000Y-119800000D02* +X124200000Y-120065686D01* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X121200000Y-88900000D02* +X122300000Y-87800000D01* +X121300000Y-97668630D02* +X121200000Y-97568629D01* +X121300000Y-105640927D02* +X121300000Y-97668630D01* +X131699999Y-115100000D02* +X130900000Y-115900000D01* +X124500000Y-67800000D02* +X129600000Y-62700000D01* +X121200000Y-97568629D02* +X121200000Y-88900000D01* +X121893900Y-106234827D02* +X121300000Y-105640927D01* +X129600000Y-62700000D02* +X131000000Y-62700000D01* +X130900000Y-115900000D02* +X129500000Y-115900000D01* +%TO.N,/XBee/XBEE_CTS*% +X127800000Y-117800000D02* +X129300000Y-117800000D01* +X129300000Y-117800000D02* +X129500000Y-117600000D01* %TO.N,/MCU_Core/RGB_DIN*% -X128701600Y-122600000D02* -X129216700Y-123115100D01* -X128260000Y-122600000D02* -X128701600Y-122600000D01* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X121461600Y-83127900D02* -X121461600Y-83804500D01* -X123136400Y-84725000D02* -X123759700Y-85348300D01* -X123759700Y-89343400D02* -X123557800Y-89545300D01* -X122700000Y-84725000D02* -X123136400Y-84725000D01* -X121461600Y-83804500D02* -X122382100Y-84725000D01* -X122700000Y-82275000D02* -X122175200Y-82799800D01* -X122382100Y-84725000D02* -X122700000Y-84725000D01* -X123557800Y-89545300D02* -X123557800Y-90439600D01* -X123759700Y-85348300D02* -X123759700Y-89343400D01* -X122175200Y-82799800D02* -X121789700Y-82799800D01* -X121789700Y-82799800D02* -X121461600Y-83127900D01* +X126862537Y-122480000D02* +X126002198Y-123340339D01* +X127900000Y-122480000D02* +X126862537Y-122480000D01* +X130400000Y-117900000D02* +X129850000Y-118450000D01* +X129500000Y-118450000D02* +X129300000Y-118450000D01* +X130400000Y-117400000D02* +X130400000Y-117900000D01* +X129850000Y-118450000D02* +X129500000Y-118450000D01* +%TO.N,/XBee/XBEE_DIN*% +X130389999Y-120689999D02* +X130550000Y-120529998D01* +X130179998Y-120689999D02* +X130389999Y-120689999D01* +X130550000Y-120529998D02* +X130550000Y-119500000D01* +%TO.N,/XBee/XBEE_DOUT*% +X131400000Y-119500000D02* +X131400000Y-118750454D01* +X131400000Y-118750454D02* +X131615136Y-118535318D01* +%TO.N,ACCEL_INT1*% +X133451471Y-116900000D02* +X132250000Y-118101471D01* +X139400000Y-116900000D02* +X133451471Y-116900000D01* +X132250000Y-118101471D02* +X132250000Y-119500000D01* %TO.N,/Buttons_Direct/BTN_VOL_UP*% -X138984500Y-85980000D02* -X135734500Y-89230000D01* -X135734500Y-89230000D02* -X135734500Y-92661400D01* -X146056200Y-74725000D02* -X146056200Y-76888000D01* -X145069700Y-77874500D02* -X145069700Y-82092700D01* -X141182400Y-85980000D02* -X138984500Y-85980000D01* +X147775000Y-74725000D02* +X147300000Y-74725000D01* +X147867157Y-94667157D02* +X146100000Y-92900000D01* +X133000000Y-118200000D02* +X133000000Y-119400000D01* +X146100000Y-84000000D02* +X145400000Y-83300000D01* +X149000000Y-73500000D02* +X147775000Y-74725000D01* X147300000Y-72275000D02* -X146979200Y-72275000D01* -X146979200Y-72275000D02* -X146056200Y-73198000D01* -X146056200Y-73198000D02* -X146056200Y-74725000D01* -X146056200Y-76888000D02* -X145069700Y-77874500D01* -X146056200Y-74725000D02* +X147775000Y-72275000D01* +X145400000Y-83300000D02* +X146100000Y-82600000D01* +X146100000Y-75925000D02* X147300000Y-74725000D01* -X145069700Y-82092700D02* -X141182400Y-85980000D01* -%TO.N,/Power_Buck/PWR_EN*% -X141116700Y-110981600D02* -X141875000Y-110223300D01* -X145850800Y-105778300D02* -X148059900Y-103569200D01* -X141875000Y-110223300D02* -X141875000Y-109800000D01* -X148059900Y-87894900D02* -X145980700Y-85815700D01* -X148059900Y-103569200D02* -X148059900Y-87894900D01* -X145850800Y-107623700D02* -X145850800Y-105778300D01* -%TO.N,/Power_Buck/BUCK_SW*% +X146100000Y-82600000D02* +X146100000Y-75925000D01* +X133000000Y-119400000D02* +X133100000Y-119500000D01* +X147034358Y-98156239D02* +X147867157Y-97323440D01* +X146100000Y-92900000D02* +X146100000Y-84000000D01* +X147867157Y-97323440D02* +X147867157Y-94667157D01* +X147775000Y-72275000D02* +X149000000Y-73500000D01* +%TO.N,/XBee/XBEE_RTS*% +X133950000Y-118250000D02* +X133900000Y-118200000D01* +X133950000Y-119500000D02* +X133950000Y-118250000D01* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147400000Y-85293629D02* +X147400000Y-85956371D01* +X147300000Y-82275000D02* +X147775000Y-82275000D01* +X147775000Y-82275000D02* +X149000000Y-83500000D01* +X134700000Y-117700000D02* +X134700000Y-119400000D01* +X134700000Y-119400000D02* +X134800000Y-119500000D01* +X147400000Y-85956371D02* +X147868629Y-86425000D01* +X147300000Y-84725000D02* +X147634315Y-85059315D01* +X147775000Y-84725000D02* +X147300000Y-84725000D01* +X148400000Y-97900000D02* +X147700000Y-98600000D01* +X147868629Y-86425000D02* +X148400000Y-86425000D01* +X147634315Y-85059315D02* +X147400000Y-85293629D01* +X148400000Y-86425000D02* +X148400000Y-97900000D01* +X149000000Y-83500000D02* +X147775000Y-84725000D01* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135650000Y-118350000D02* +X135600000Y-118300000D01* +X135650000Y-119500000D02* +X135650000Y-118350000D01* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-119500000D02* +X136500000Y-118300000D01* +%TO.N,/MCU_Core/PWR_HOLD*% +X138200000Y-119000000D02* +X141400000Y-115800000D01* +X138485000Y-74588529D02* +X138485000Y-72539999D01* +X141400000Y-113951471D02* +X141751471Y-113600000D01* +X136825000Y-76248529D02* +X138485000Y-74588529D01* +X138200000Y-119500000D02* +X138200000Y-119000000D01* +X136825000Y-84840255D02* +X136825000Y-76248529D01* +X140950000Y-88965255D02* +X136825000Y-84840255D01* +X140950000Y-90700000D02* +X140950000Y-88965255D01* +X142000000Y-113600000D02* +X142000000Y-107300000D01* +X141400000Y-115800000D02* +X141400000Y-113951471D01* +X141751471Y-113600000D02* +X142000000Y-113600000D01* +%TO.N,VBUS*% +D51* +X137000000Y-124900000D02* +X138379999Y-124900000D01* +X122800000Y-100825000D02* +X125450000Y-98175000D01* +X138379999Y-124900000D02* +X139450000Y-123829999D01* +X137000000Y-124900000D02* +X135620001Y-124900000D01* +X139450000Y-123829999D02* +X139450000Y-123105000D01* +X122800000Y-102300000D02* +X122800000Y-100825000D01* +X135620001Y-124900000D02* +X134550000Y-123829999D01* +X122300000Y-102800000D02* +X122800000Y-102300000D01* +X134550000Y-123829999D02* +X134550000Y-123105000D01* +X125450000Y-98175000D02* +X125450000Y-95960050D01* +X124739950Y-95250000D02* +X123750000Y-95250000D01* +X125450000Y-95960050D02* +X124739950Y-95250000D01* +%TO.N,/USB_C/USB_CC1*% +D49* +X135750000Y-123105000D02* +X135750000Y-122347590D01* +X130820000Y-122080000D02* +X129200000Y-123700000D01* +X135482410Y-122080000D02* +X130820000Y-122080000D01* +X135750000Y-122347590D02* +X135482410Y-122080000D01* +%TO.N,/MCU_Core/USB_DP*% +X136657357Y-121254947D02* +X130463578Y-121254947D01* +X126689999Y-121289999D02* +X125000000Y-119600000D01* +X137750000Y-122347590D02* +X137251205Y-121848795D01* +X125000000Y-119600000D02* +X125000000Y-117600000D01* +X125700000Y-116880000D02* +X128100000Y-116880000D01* +X130428527Y-121289999D02* +X126689999Y-121289999D01* +X137750000Y-123105000D02* +X137750000Y-122347590D01* +X137202410Y-121800000D02* +X137200000Y-121800000D01* +X137251205Y-121848795D02* +X136657357Y-121254947D01* +X137251205Y-121848795D02* +X137202410Y-121800000D01* +X136750000Y-122250000D02* +X136750000Y-123105000D01* +X130463578Y-121254947D02* +X130428527Y-121289999D01* +X137200000Y-121800000D02* +X136750000Y-122250000D01* +X125000000Y-117600000D02* +X125700000Y-116880000D01* +%TO.N,/USB_C/USB_CC2*% +X138750000Y-122380001D02* +X139050001Y-122080000D01* +X139050001Y-122080000D02* +X141061371Y-122080000D01* +X138750000Y-123105000D02* +X138750000Y-122380001D01* +X142300000Y-123318629D02* +X142300000Y-124900000D01* +X141061371Y-122080000D02* +X142300000Y-123318629D01* +%TO.N,VSYS*% +D51* +X129700000Y-100800000D02* +X129700000Y-93350000D01* +X129800000Y-100900000D02* +X129700000Y-100800000D01* +X144600000Y-86300000D02* +X144600000Y-84406192D01* +X144600000Y-90450000D02* +X144800000Y-90650000D01* +X142100000Y-81906192D02* +X142100000Y-79300000D01* +X144600000Y-86300000D02* +X144600000Y-90450000D01* +X144600000Y-84406192D02* +X142100000Y-81906192D01* +%TO.N,VBAT*% D52* -X139975000Y-109800000D02* -X137500000Y-109800000D01* -%TO.N,/Buttons_Direct/BTN_MACRO5*% +X137700000Y-99400000D02* +X138600000Y-100300000D01* +X146800000Y-99000000D02* +X148400000Y-100600000D01* +X148400000Y-108200000D02* +X147300000Y-109300000D01* +X148400000Y-100600000D02* +X148400000Y-108200000D01* +X137700000Y-99000000D02* +X137700000Y-99400000D01* +X139900000Y-99000000D02* +X146800000Y-99000000D01* +X138600000Y-100300000D02* +X139900000Y-99000000D01* +X135900000Y-99000000D02* +X137700000Y-99000000D01* +%TO.N,/Power_Buck/BUCK_FB*% D50* -X135450000Y-103150000D02* -X134850000Y-103150000D01* -X134600000Y-103100000D02* -X133000000Y-101500000D01* -X134157300Y-101855600D02* -X133751700Y-101450000D01* -X135500000Y-103200000D02* -X135450000Y-103150000D01* -X135700000Y-103250000D02* -X135650000Y-103200000D01* -X136669400Y-101855600D02* -X134157300Y-101855600D01* -X134850000Y-103150000D02* -X134800000Y-103100000D01* -X135750000Y-103250000D02* -X135700000Y-103250000D01* -X137075000Y-101450000D02* -X136669400Y-101855600D01* -X136150000Y-104250000D02* -X136150000Y-103650000D01* -X134800000Y-103100000D02* -X134600000Y-103100000D01* -X136150000Y-103650000D02* -X135750000Y-103250000D01* -X135650000Y-103200000D02* -X135500000Y-103200000D01* -X132925000Y-101450000D02* -X133751700Y-101450000D01* -%TO.N,ACCEL_INT1*% -X140522000Y-87583700D02* -X145767400Y-82338300D01* -X145767400Y-77985600D02* -X147014800Y-76738200D01* -X145767400Y-82338300D02* -X145767400Y-77985600D01* -X147014800Y-76738200D02* -X147014800Y-76170200D01* -X140522000Y-96623500D02* -X140522000Y-87583700D01* -X139636800Y-97508700D02* -X140522000Y-96623500D01* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X135000000Y-61269100D02* -X139093200Y-65362300D01* -X139093200Y-65362300D02* -X139093200Y-77566200D01* -X134105300Y-82554100D02* -X134105300Y-87305100D01* -X139093200Y-77566200D02* -X134105300Y-82554100D01* -%TO.N,/MCU_Core/PWR_HOLD*% -X131156900Y-92854700D02* -X129605600Y-94406000D01* -X133294500Y-89504100D02* -X131156900Y-91641700D01* -X138485000Y-72540000D02* -X133294500Y-77730500D01* -X133294500Y-77730500D02* -X133294500Y-89504100D01* -X131156900Y-91641700D02* -X131156900Y-92854700D01* -X129605600Y-98218100D02* -X129625000Y-98237500D01* -X129605600Y-94406000D02* -X129605600Y-98218100D01* -%TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127260700Y-66852300D02* -X126692500Y-67420500D01* -X126692500Y-67420500D02* -X126692500Y-80628700D01* +X139500000Y-97700000D02* +X139500000Y-94850000D01* +X139885887Y-98085887D02* +X139500000Y-97700000D01* +X139885887Y-98225129D02* +X139885887Y-98085887D01* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-F_Mask.gbr b/PCB/v2.x/production/gerbers/snips_controller-F_Mask.gbr index 0fa742a..617d17b 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-F_Mask.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-F_Mask.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Soldermask,Top*% %TF.FilePolarity,Negative*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -28,15 +28,17 @@ G04 Aperture macros list* 20,1,$1+$1,$4,$5,$6,$7,0* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% +%AMFreePoly0* +4,1,6,0.600000,-0.600000,-0.600000,-0.600000,-0.600000,0.000000,0.000000,0.600000,0.600000,0.600000,0.600000,-0.600000,0.600000,-0.600000,$1*% G04 Aperture macros list end* -%ADD10C,0.010000*% -%ADD11RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% -%ADD12R,1.050000X0.650000*% -%ADD13RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% -%ADD14RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% -%ADD15RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% -%ADD16RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% -%ADD17C,2.000000*% +%ADD10RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% +%ADD11R,1.050000X0.650000*% +%ADD12RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% +%ADD13RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD14R,0.650000X1.050000*% +%ADD15C,2.000000*% +%ADD16RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% +%ADD17RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% %ADD18C,0.900000*% %ADD19RoundRect,0.187500X-0.712500X0.187500X-0.712500X-0.187500X0.712500X-0.187500X0.712500X0.187500X0*% %ADD20RoundRect,0.150000X-0.750000X0.150000X-0.750000X-0.150000X0.750000X-0.150000X0.750000X0.150000X0*% @@ -45,2868 +47,90 @@ G04 Aperture macros list end* %ADD23C,2.200000*% %ADD24RoundRect,0.150000X-0.150000X-0.625000X0.150000X-0.625000X0.150000X0.625000X-0.150000X0.625000X0*% %ADD25RoundRect,0.250000X-0.350000X-0.650000X0.350000X-0.650000X0.350000X0.650000X-0.350000X0.650000X0*% -%ADD26RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% -%ADD27RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% -%ADD28RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% -%ADD29RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% -%ADD30C,0.650000*% -%ADD31RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% -%ADD32RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% -%ADD33O,1.000000X2.100000*% -%ADD34O,1.000000X1.600000*% -%ADD35RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% -%ADD36C,2.750000*% -%ADD37C,2.250000*% -%ADD38C,2.450000*% -%ADD39RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% -%ADD40RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% -%ADD41RoundRect,0.150000X-0.150000X0.512500X-0.150000X-0.512500X0.150000X-0.512500X0.150000X0.512500X0*% -%ADD42R,1.500000X3.600000*% -%ADD43RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% -%ADD44RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% -%ADD45RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% -%ADD46RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% -%ADD47O,1.200000X1.750000*% -%ADD48C,0.990600*% +%ADD26RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%ADD27R,0.400000X0.800000*% +%ADD28R,0.800000X0.400000*% +%ADD29FreePoly0,270.000000*% +%ADD30R,1.200000X1.200000*% +%ADD31R,0.800000X0.800000*% +%ADD32RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% +%ADD33RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% +%ADD34RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% +%ADD35C,0.650000*% +%ADD36RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% +%ADD37RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% +%ADD38O,1.000000X2.100000*% +%ADD39O,1.000000X1.600000*% +%ADD40C,2.750000*% +%ADD41C,2.250000*% +%ADD42C,2.450000*% +%ADD43RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% +%ADD44RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD45RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% +%ADD46RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% +%ADD47RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% +%ADD48RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% +%ADD49O,1.200000X1.750000*% G04 APERTURE END LIST* D10* -%TO.C,U_CHG1*% -X129000000Y-117415000D02* -X129000000Y-117615000D01* -X129000000Y-117618000D01* -X129000000Y-117620000D01* -X128999000Y-117623000D01* -X128999000Y-117625000D01* -X128998000Y-117628000D01* -X128998000Y-117630000D01* -X128997000Y-117633000D01* -X128996000Y-117635000D01* -X128995000Y-117638000D01* -X128993000Y-117640000D01* -X128992000Y-117642000D01* -X128990000Y-117644000D01* -X128989000Y-117646000D01* -X128987000Y-117648000D01* -X128985000Y-117650000D01* -X128983000Y-117652000D01* -X128981000Y-117654000D01* -X128979000Y-117655000D01* -X128977000Y-117657000D01* -X128975000Y-117658000D01* -X128973000Y-117660000D01* -X128970000Y-117661000D01* -X128968000Y-117662000D01* -X128965000Y-117663000D01* -X128963000Y-117663000D01* -X128960000Y-117664000D01* -X128958000Y-117664000D01* -X128955000Y-117665000D01* -X128953000Y-117665000D01* -X128950000Y-117665000D01* -X128450000Y-117665000D01* -X128447000Y-117665000D01* -X128445000Y-117665000D01* -X128442000Y-117664000D01* -X128440000Y-117664000D01* -X128437000Y-117663000D01* -X128435000Y-117663000D01* -X128432000Y-117662000D01* -X128430000Y-117661000D01* -X128427000Y-117660000D01* -X128425000Y-117658000D01* -X128423000Y-117657000D01* -X128421000Y-117655000D01* -X128419000Y-117654000D01* -X128417000Y-117652000D01* -X128415000Y-117650000D01* -X128413000Y-117648000D01* -X128411000Y-117646000D01* -X128410000Y-117644000D01* -X128408000Y-117642000D01* -X128407000Y-117640000D01* -X128405000Y-117638000D01* -X128404000Y-117635000D01* -X128403000Y-117633000D01* -X128402000Y-117630000D01* -X128402000Y-117628000D01* -X128401000Y-117625000D01* -X128401000Y-117623000D01* -X128400000Y-117620000D01* -X128400000Y-117618000D01* -X128400000Y-117615000D01* -X128400000Y-117415000D01* -X128400000Y-117412000D01* -X128400000Y-117410000D01* -X128401000Y-117407000D01* -X128401000Y-117405000D01* -X128402000Y-117402000D01* -X128402000Y-117400000D01* -X128403000Y-117397000D01* -X128404000Y-117395000D01* -X128405000Y-117392000D01* -X128407000Y-117390000D01* -X128408000Y-117388000D01* -X128410000Y-117386000D01* -X128411000Y-117384000D01* -X128413000Y-117382000D01* -X128415000Y-117380000D01* -X128417000Y-117378000D01* -X128419000Y-117376000D01* -X128421000Y-117375000D01* -X128423000Y-117373000D01* -X128425000Y-117372000D01* -X128427000Y-117370000D01* -X128430000Y-117369000D01* -X128432000Y-117368000D01* -X128435000Y-117367000D01* -X128437000Y-117367000D01* -X128440000Y-117366000D01* -X128442000Y-117366000D01* -X128445000Y-117365000D01* -X128447000Y-117365000D01* -X128450000Y-117365000D01* -X128950000Y-117365000D01* -X128953000Y-117365000D01* -X128955000Y-117365000D01* -X128958000Y-117366000D01* -X128960000Y-117366000D01* -X128963000Y-117367000D01* -X128965000Y-117367000D01* -X128968000Y-117368000D01* -X128970000Y-117369000D01* -X128973000Y-117370000D01* -X128975000Y-117372000D01* -X128977000Y-117373000D01* -X128979000Y-117375000D01* -X128981000Y-117376000D01* -X128983000Y-117378000D01* -X128985000Y-117380000D01* -X128987000Y-117382000D01* -X128989000Y-117384000D01* -X128990000Y-117386000D01* -X128992000Y-117388000D01* -X128993000Y-117390000D01* -X128995000Y-117392000D01* -X128996000Y-117395000D01* -X128997000Y-117397000D01* -X128998000Y-117400000D01* -X128998000Y-117402000D01* -X128999000Y-117405000D01* -X128999000Y-117407000D01* -X129000000Y-117410000D01* -X129000000Y-117412000D01* -X129000000Y-117415000D01* -G36* -X128958000Y-117366000D02* -G01* -X128960000Y-117366000D01* -X128963000Y-117367000D01* -X128965000Y-117367000D01* -X128968000Y-117368000D01* -X128970000Y-117369000D01* -X128973000Y-117370000D01* -X128975000Y-117372000D01* -X128977000Y-117373000D01* -X128979000Y-117375000D01* -X128981000Y-117376000D01* -X128983000Y-117378000D01* -X128985000Y-117380000D01* -X128987000Y-117382000D01* -X128989000Y-117384000D01* -X128990000Y-117386000D01* -X128992000Y-117388000D01* -X128993000Y-117390000D01* -X128995000Y-117392000D01* -X128996000Y-117395000D01* -X128997000Y-117397000D01* -X128998000Y-117400000D01* -X128998000Y-117402000D01* -X128999000Y-117405000D01* -X128999000Y-117407000D01* -X129000000Y-117410000D01* -X129000000Y-117412000D01* -X129000000Y-117415000D01* -X129000000Y-117615000D01* -X129000000Y-117618000D01* -X129000000Y-117620000D01* -X128999000Y-117623000D01* -X128999000Y-117625000D01* -X128998000Y-117628000D01* -X128998000Y-117630000D01* -X128997000Y-117633000D01* -X128996000Y-117635000D01* -X128995000Y-117638000D01* -X128993000Y-117640000D01* -X128992000Y-117642000D01* -X128990000Y-117644000D01* -X128989000Y-117646000D01* -X128987000Y-117648000D01* -X128985000Y-117650000D01* -X128983000Y-117652000D01* -X128981000Y-117654000D01* -X128979000Y-117655000D01* -X128977000Y-117657000D01* -X128975000Y-117658000D01* -X128973000Y-117660000D01* -X128970000Y-117661000D01* -X128968000Y-117662000D01* -X128965000Y-117663000D01* -X128963000Y-117663000D01* -X128960000Y-117664000D01* -X128958000Y-117664000D01* -X128955000Y-117665000D01* -X128953000Y-117665000D01* -X128950000Y-117665000D01* -X128450000Y-117665000D01* -X128447000Y-117665000D01* -X128445000Y-117665000D01* -X128442000Y-117664000D01* -X128440000Y-117664000D01* -X128437000Y-117663000D01* -X128435000Y-117663000D01* -X128432000Y-117662000D01* -X128430000Y-117661000D01* -X128427000Y-117660000D01* -X128425000Y-117658000D01* -X128423000Y-117657000D01* -X128421000Y-117655000D01* -X128419000Y-117654000D01* -X128417000Y-117652000D01* -X128415000Y-117650000D01* -X128413000Y-117648000D01* -X128411000Y-117646000D01* -X128410000Y-117644000D01* -X128408000Y-117642000D01* -X128407000Y-117640000D01* -X128405000Y-117638000D01* -X128404000Y-117635000D01* -X128403000Y-117633000D01* -X128402000Y-117630000D01* -X128402000Y-117628000D01* -X128401000Y-117625000D01* -X128401000Y-117623000D01* -X128400000Y-117620000D01* -X128400000Y-117618000D01* -X128400000Y-117615000D01* -X128400000Y-117415000D01* -X128400000Y-117412000D01* -X128400000Y-117410000D01* -X128401000Y-117407000D01* -X128401000Y-117405000D01* -X128402000Y-117402000D01* -X128402000Y-117400000D01* -X128403000Y-117397000D01* -X128404000Y-117395000D01* -X128405000Y-117392000D01* -X128407000Y-117390000D01* -X128408000Y-117388000D01* -X128410000Y-117386000D01* -X128411000Y-117384000D01* -X128413000Y-117382000D01* -X128415000Y-117380000D01* -X128417000Y-117378000D01* -X128419000Y-117376000D01* -X128421000Y-117375000D01* -X128423000Y-117373000D01* -X128425000Y-117372000D01* -X128427000Y-117370000D01* -X128430000Y-117369000D01* -X128432000Y-117368000D01* -X128435000Y-117367000D01* -X128437000Y-117367000D01* -X128440000Y-117366000D01* -X128442000Y-117366000D01* -X128445000Y-117365000D01* -X128447000Y-117365000D01* -X128450000Y-117365000D01* -X128950000Y-117365000D01* -X128953000Y-117365000D01* -X128955000Y-117365000D01* -X128958000Y-117366000D01* -G37* -X129000000Y-117815000D02* -X129000000Y-118015000D01* -X129000000Y-118018000D01* -X129000000Y-118020000D01* -X128999000Y-118023000D01* -X128999000Y-118025000D01* -X128998000Y-118028000D01* -X128998000Y-118030000D01* -X128997000Y-118033000D01* -X128996000Y-118035000D01* -X128995000Y-118038000D01* -X128993000Y-118040000D01* -X128992000Y-118042000D01* -X128990000Y-118044000D01* -X128989000Y-118046000D01* -X128987000Y-118048000D01* -X128985000Y-118050000D01* -X128983000Y-118052000D01* -X128981000Y-118054000D01* -X128979000Y-118055000D01* -X128977000Y-118057000D01* -X128975000Y-118058000D01* -X128973000Y-118060000D01* -X128970000Y-118061000D01* -X128968000Y-118062000D01* -X128965000Y-118063000D01* -X128963000Y-118063000D01* -X128960000Y-118064000D01* -X128958000Y-118064000D01* -X128955000Y-118065000D01* -X128953000Y-118065000D01* -X128950000Y-118065000D01* -X128450000Y-118065000D01* -X128447000Y-118065000D01* -X128445000Y-118065000D01* -X128442000Y-118064000D01* -X128440000Y-118064000D01* -X128437000Y-118063000D01* -X128435000Y-118063000D01* -X128432000Y-118062000D01* -X128430000Y-118061000D01* -X128427000Y-118060000D01* -X128425000Y-118058000D01* -X128423000Y-118057000D01* -X128421000Y-118055000D01* -X128419000Y-118054000D01* -X128417000Y-118052000D01* -X128415000Y-118050000D01* -X128413000Y-118048000D01* -X128411000Y-118046000D01* -X128410000Y-118044000D01* -X128408000Y-118042000D01* -X128407000Y-118040000D01* -X128405000Y-118038000D01* -X128404000Y-118035000D01* -X128403000Y-118033000D01* -X128402000Y-118030000D01* -X128402000Y-118028000D01* -X128401000Y-118025000D01* -X128401000Y-118023000D01* -X128400000Y-118020000D01* -X128400000Y-118018000D01* -X128400000Y-118015000D01* -X128400000Y-117815000D01* -X128400000Y-117812000D01* -X128400000Y-117810000D01* -X128401000Y-117807000D01* -X128401000Y-117805000D01* -X128402000Y-117802000D01* -X128402000Y-117800000D01* -X128403000Y-117797000D01* -X128404000Y-117795000D01* -X128405000Y-117792000D01* -X128407000Y-117790000D01* -X128408000Y-117788000D01* -X128410000Y-117786000D01* -X128411000Y-117784000D01* -X128413000Y-117782000D01* -X128415000Y-117780000D01* -X128417000Y-117778000D01* -X128419000Y-117776000D01* -X128421000Y-117775000D01* -X128423000Y-117773000D01* -X128425000Y-117772000D01* -X128427000Y-117770000D01* -X128430000Y-117769000D01* -X128432000Y-117768000D01* -X128435000Y-117767000D01* -X128437000Y-117767000D01* -X128440000Y-117766000D01* -X128442000Y-117766000D01* -X128445000Y-117765000D01* -X128447000Y-117765000D01* -X128450000Y-117765000D01* -X128950000Y-117765000D01* -X128953000Y-117765000D01* -X128955000Y-117765000D01* -X128958000Y-117766000D01* -X128960000Y-117766000D01* -X128963000Y-117767000D01* -X128965000Y-117767000D01* -X128968000Y-117768000D01* -X128970000Y-117769000D01* -X128973000Y-117770000D01* -X128975000Y-117772000D01* -X128977000Y-117773000D01* -X128979000Y-117775000D01* -X128981000Y-117776000D01* -X128983000Y-117778000D01* -X128985000Y-117780000D01* -X128987000Y-117782000D01* -X128989000Y-117784000D01* -X128990000Y-117786000D01* -X128992000Y-117788000D01* -X128993000Y-117790000D01* -X128995000Y-117792000D01* -X128996000Y-117795000D01* -X128997000Y-117797000D01* -X128998000Y-117800000D01* -X128998000Y-117802000D01* -X128999000Y-117805000D01* -X128999000Y-117807000D01* -X129000000Y-117810000D01* -X129000000Y-117812000D01* -X129000000Y-117815000D01* -G36* -X128958000Y-117766000D02* -G01* -X128960000Y-117766000D01* -X128963000Y-117767000D01* -X128965000Y-117767000D01* -X128968000Y-117768000D01* -X128970000Y-117769000D01* -X128973000Y-117770000D01* -X128975000Y-117772000D01* -X128977000Y-117773000D01* -X128979000Y-117775000D01* -X128981000Y-117776000D01* -X128983000Y-117778000D01* -X128985000Y-117780000D01* -X128987000Y-117782000D01* -X128989000Y-117784000D01* -X128990000Y-117786000D01* -X128992000Y-117788000D01* -X128993000Y-117790000D01* -X128995000Y-117792000D01* -X128996000Y-117795000D01* -X128997000Y-117797000D01* -X128998000Y-117800000D01* -X128998000Y-117802000D01* -X128999000Y-117805000D01* -X128999000Y-117807000D01* -X129000000Y-117810000D01* -X129000000Y-117812000D01* -X129000000Y-117815000D01* -X129000000Y-118015000D01* -X129000000Y-118018000D01* -X129000000Y-118020000D01* -X128999000Y-118023000D01* -X128999000Y-118025000D01* -X128998000Y-118028000D01* -X128998000Y-118030000D01* -X128997000Y-118033000D01* -X128996000Y-118035000D01* -X128995000Y-118038000D01* -X128993000Y-118040000D01* -X128992000Y-118042000D01* -X128990000Y-118044000D01* -X128989000Y-118046000D01* -X128987000Y-118048000D01* -X128985000Y-118050000D01* -X128983000Y-118052000D01* -X128981000Y-118054000D01* -X128979000Y-118055000D01* -X128977000Y-118057000D01* -X128975000Y-118058000D01* -X128973000Y-118060000D01* -X128970000Y-118061000D01* -X128968000Y-118062000D01* -X128965000Y-118063000D01* -X128963000Y-118063000D01* -X128960000Y-118064000D01* -X128958000Y-118064000D01* -X128955000Y-118065000D01* -X128953000Y-118065000D01* -X128950000Y-118065000D01* -X128450000Y-118065000D01* -X128447000Y-118065000D01* -X128445000Y-118065000D01* -X128442000Y-118064000D01* -X128440000Y-118064000D01* -X128437000Y-118063000D01* -X128435000Y-118063000D01* -X128432000Y-118062000D01* -X128430000Y-118061000D01* -X128427000Y-118060000D01* -X128425000Y-118058000D01* -X128423000Y-118057000D01* -X128421000Y-118055000D01* -X128419000Y-118054000D01* -X128417000Y-118052000D01* -X128415000Y-118050000D01* -X128413000Y-118048000D01* -X128411000Y-118046000D01* -X128410000Y-118044000D01* -X128408000Y-118042000D01* -X128407000Y-118040000D01* -X128405000Y-118038000D01* -X128404000Y-118035000D01* -X128403000Y-118033000D01* -X128402000Y-118030000D01* -X128402000Y-118028000D01* -X128401000Y-118025000D01* -X128401000Y-118023000D01* -X128400000Y-118020000D01* -X128400000Y-118018000D01* -X128400000Y-118015000D01* -X128400000Y-117815000D01* -X128400000Y-117812000D01* -X128400000Y-117810000D01* -X128401000Y-117807000D01* -X128401000Y-117805000D01* -X128402000Y-117802000D01* -X128402000Y-117800000D01* -X128403000Y-117797000D01* -X128404000Y-117795000D01* -X128405000Y-117792000D01* -X128407000Y-117790000D01* -X128408000Y-117788000D01* -X128410000Y-117786000D01* -X128411000Y-117784000D01* -X128413000Y-117782000D01* -X128415000Y-117780000D01* -X128417000Y-117778000D01* -X128419000Y-117776000D01* -X128421000Y-117775000D01* -X128423000Y-117773000D01* -X128425000Y-117772000D01* -X128427000Y-117770000D01* -X128430000Y-117769000D01* -X128432000Y-117768000D01* -X128435000Y-117767000D01* -X128437000Y-117767000D01* -X128440000Y-117766000D01* -X128442000Y-117766000D01* -X128445000Y-117765000D01* -X128447000Y-117765000D01* -X128450000Y-117765000D01* -X128950000Y-117765000D01* -X128953000Y-117765000D01* -X128955000Y-117765000D01* -X128958000Y-117766000D01* -G37* -X129000000Y-118215000D02* -X129000000Y-118415000D01* -X129000000Y-118418000D01* -X129000000Y-118420000D01* -X128999000Y-118423000D01* -X128999000Y-118425000D01* -X128998000Y-118428000D01* -X128998000Y-118430000D01* -X128997000Y-118433000D01* -X128996000Y-118435000D01* -X128995000Y-118438000D01* -X128993000Y-118440000D01* -X128992000Y-118442000D01* -X128990000Y-118444000D01* -X128989000Y-118446000D01* -X128987000Y-118448000D01* -X128985000Y-118450000D01* -X128983000Y-118452000D01* -X128981000Y-118454000D01* -X128979000Y-118455000D01* -X128977000Y-118457000D01* -X128975000Y-118458000D01* -X128973000Y-118460000D01* -X128970000Y-118461000D01* -X128968000Y-118462000D01* -X128965000Y-118463000D01* -X128963000Y-118463000D01* -X128960000Y-118464000D01* -X128958000Y-118464000D01* -X128955000Y-118465000D01* -X128953000Y-118465000D01* -X128950000Y-118465000D01* -X128450000Y-118465000D01* -X128447000Y-118465000D01* -X128445000Y-118465000D01* -X128442000Y-118464000D01* -X128440000Y-118464000D01* -X128437000Y-118463000D01* -X128435000Y-118463000D01* -X128432000Y-118462000D01* -X128430000Y-118461000D01* -X128427000Y-118460000D01* -X128425000Y-118458000D01* -X128423000Y-118457000D01* -X128421000Y-118455000D01* -X128419000Y-118454000D01* -X128417000Y-118452000D01* -X128415000Y-118450000D01* -X128413000Y-118448000D01* -X128411000Y-118446000D01* -X128410000Y-118444000D01* -X128408000Y-118442000D01* -X128407000Y-118440000D01* -X128405000Y-118438000D01* -X128404000Y-118435000D01* -X128403000Y-118433000D01* -X128402000Y-118430000D01* -X128402000Y-118428000D01* -X128401000Y-118425000D01* -X128401000Y-118423000D01* -X128400000Y-118420000D01* -X128400000Y-118418000D01* -X128400000Y-118415000D01* -X128400000Y-118215000D01* -X128400000Y-118212000D01* -X128400000Y-118210000D01* -X128401000Y-118207000D01* -X128401000Y-118205000D01* -X128402000Y-118202000D01* -X128402000Y-118200000D01* -X128403000Y-118197000D01* -X128404000Y-118195000D01* -X128405000Y-118192000D01* -X128407000Y-118190000D01* -X128408000Y-118188000D01* -X128410000Y-118186000D01* -X128411000Y-118184000D01* -X128413000Y-118182000D01* -X128415000Y-118180000D01* -X128417000Y-118178000D01* -X128419000Y-118176000D01* -X128421000Y-118175000D01* -X128423000Y-118173000D01* -X128425000Y-118172000D01* -X128427000Y-118170000D01* -X128430000Y-118169000D01* -X128432000Y-118168000D01* -X128435000Y-118167000D01* -X128437000Y-118167000D01* -X128440000Y-118166000D01* -X128442000Y-118166000D01* -X128445000Y-118165000D01* -X128447000Y-118165000D01* -X128450000Y-118165000D01* -X128950000Y-118165000D01* -X128953000Y-118165000D01* -X128955000Y-118165000D01* -X128958000Y-118166000D01* -X128960000Y-118166000D01* -X128963000Y-118167000D01* -X128965000Y-118167000D01* -X128968000Y-118168000D01* -X128970000Y-118169000D01* -X128973000Y-118170000D01* -X128975000Y-118172000D01* -X128977000Y-118173000D01* -X128979000Y-118175000D01* -X128981000Y-118176000D01* -X128983000Y-118178000D01* -X128985000Y-118180000D01* -X128987000Y-118182000D01* -X128989000Y-118184000D01* -X128990000Y-118186000D01* -X128992000Y-118188000D01* -X128993000Y-118190000D01* -X128995000Y-118192000D01* -X128996000Y-118195000D01* -X128997000Y-118197000D01* -X128998000Y-118200000D01* -X128998000Y-118202000D01* -X128999000Y-118205000D01* -X128999000Y-118207000D01* -X129000000Y-118210000D01* -X129000000Y-118212000D01* -X129000000Y-118215000D01* -G36* -X128958000Y-118166000D02* -G01* -X128960000Y-118166000D01* -X128963000Y-118167000D01* -X128965000Y-118167000D01* -X128968000Y-118168000D01* -X128970000Y-118169000D01* -X128973000Y-118170000D01* -X128975000Y-118172000D01* -X128977000Y-118173000D01* -X128979000Y-118175000D01* -X128981000Y-118176000D01* -X128983000Y-118178000D01* -X128985000Y-118180000D01* -X128987000Y-118182000D01* -X128989000Y-118184000D01* -X128990000Y-118186000D01* -X128992000Y-118188000D01* -X128993000Y-118190000D01* -X128995000Y-118192000D01* -X128996000Y-118195000D01* -X128997000Y-118197000D01* -X128998000Y-118200000D01* -X128998000Y-118202000D01* -X128999000Y-118205000D01* -X128999000Y-118207000D01* -X129000000Y-118210000D01* -X129000000Y-118212000D01* -X129000000Y-118215000D01* -X129000000Y-118415000D01* -X129000000Y-118418000D01* -X129000000Y-118420000D01* -X128999000Y-118423000D01* -X128999000Y-118425000D01* -X128998000Y-118428000D01* -X128998000Y-118430000D01* -X128997000Y-118433000D01* -X128996000Y-118435000D01* -X128995000Y-118438000D01* -X128993000Y-118440000D01* -X128992000Y-118442000D01* -X128990000Y-118444000D01* -X128989000Y-118446000D01* -X128987000Y-118448000D01* -X128985000Y-118450000D01* -X128983000Y-118452000D01* -X128981000Y-118454000D01* -X128979000Y-118455000D01* -X128977000Y-118457000D01* -X128975000Y-118458000D01* -X128973000Y-118460000D01* -X128970000Y-118461000D01* -X128968000Y-118462000D01* -X128965000Y-118463000D01* -X128963000Y-118463000D01* -X128960000Y-118464000D01* -X128958000Y-118464000D01* -X128955000Y-118465000D01* -X128953000Y-118465000D01* -X128950000Y-118465000D01* -X128450000Y-118465000D01* -X128447000Y-118465000D01* -X128445000Y-118465000D01* -X128442000Y-118464000D01* -X128440000Y-118464000D01* -X128437000Y-118463000D01* -X128435000Y-118463000D01* -X128432000Y-118462000D01* -X128430000Y-118461000D01* -X128427000Y-118460000D01* -X128425000Y-118458000D01* -X128423000Y-118457000D01* -X128421000Y-118455000D01* -X128419000Y-118454000D01* -X128417000Y-118452000D01* -X128415000Y-118450000D01* -X128413000Y-118448000D01* -X128411000Y-118446000D01* -X128410000Y-118444000D01* -X128408000Y-118442000D01* -X128407000Y-118440000D01* -X128405000Y-118438000D01* -X128404000Y-118435000D01* -X128403000Y-118433000D01* -X128402000Y-118430000D01* -X128402000Y-118428000D01* -X128401000Y-118425000D01* -X128401000Y-118423000D01* -X128400000Y-118420000D01* -X128400000Y-118418000D01* -X128400000Y-118415000D01* -X128400000Y-118215000D01* -X128400000Y-118212000D01* -X128400000Y-118210000D01* -X128401000Y-118207000D01* -X128401000Y-118205000D01* -X128402000Y-118202000D01* -X128402000Y-118200000D01* -X128403000Y-118197000D01* -X128404000Y-118195000D01* -X128405000Y-118192000D01* -X128407000Y-118190000D01* -X128408000Y-118188000D01* -X128410000Y-118186000D01* -X128411000Y-118184000D01* -X128413000Y-118182000D01* -X128415000Y-118180000D01* -X128417000Y-118178000D01* -X128419000Y-118176000D01* -X128421000Y-118175000D01* -X128423000Y-118173000D01* -X128425000Y-118172000D01* -X128427000Y-118170000D01* -X128430000Y-118169000D01* -X128432000Y-118168000D01* -X128435000Y-118167000D01* -X128437000Y-118167000D01* -X128440000Y-118166000D01* -X128442000Y-118166000D01* -X128445000Y-118165000D01* -X128447000Y-118165000D01* -X128450000Y-118165000D01* -X128950000Y-118165000D01* -X128953000Y-118165000D01* -X128955000Y-118165000D01* -X128958000Y-118166000D01* -G37* -X129000000Y-118615000D02* -X129000000Y-118815000D01* -X129000000Y-118818000D01* -X129000000Y-118820000D01* -X128999000Y-118823000D01* -X128999000Y-118825000D01* -X128998000Y-118828000D01* -X128998000Y-118830000D01* -X128997000Y-118833000D01* -X128996000Y-118835000D01* -X128995000Y-118838000D01* -X128993000Y-118840000D01* -X128992000Y-118842000D01* -X128990000Y-118844000D01* -X128989000Y-118846000D01* -X128987000Y-118848000D01* -X128985000Y-118850000D01* -X128983000Y-118852000D01* -X128981000Y-118854000D01* -X128979000Y-118855000D01* -X128977000Y-118857000D01* -X128975000Y-118858000D01* -X128973000Y-118860000D01* -X128970000Y-118861000D01* -X128968000Y-118862000D01* -X128965000Y-118863000D01* -X128963000Y-118863000D01* -X128960000Y-118864000D01* -X128958000Y-118864000D01* -X128955000Y-118865000D01* -X128953000Y-118865000D01* -X128950000Y-118865000D01* -X128450000Y-118865000D01* -X128447000Y-118865000D01* -X128445000Y-118865000D01* -X128442000Y-118864000D01* -X128440000Y-118864000D01* -X128437000Y-118863000D01* -X128435000Y-118863000D01* -X128432000Y-118862000D01* -X128430000Y-118861000D01* -X128427000Y-118860000D01* -X128425000Y-118858000D01* -X128423000Y-118857000D01* -X128421000Y-118855000D01* -X128419000Y-118854000D01* -X128417000Y-118852000D01* -X128415000Y-118850000D01* -X128413000Y-118848000D01* -X128411000Y-118846000D01* -X128410000Y-118844000D01* -X128408000Y-118842000D01* -X128407000Y-118840000D01* -X128405000Y-118838000D01* -X128404000Y-118835000D01* -X128403000Y-118833000D01* -X128402000Y-118830000D01* -X128402000Y-118828000D01* -X128401000Y-118825000D01* -X128401000Y-118823000D01* -X128400000Y-118820000D01* -X128400000Y-118818000D01* -X128400000Y-118815000D01* -X128400000Y-118615000D01* -X128400000Y-118612000D01* -X128400000Y-118610000D01* -X128401000Y-118607000D01* -X128401000Y-118605000D01* -X128402000Y-118602000D01* -X128402000Y-118600000D01* -X128403000Y-118597000D01* -X128404000Y-118595000D01* -X128405000Y-118592000D01* -X128407000Y-118590000D01* -X128408000Y-118588000D01* -X128410000Y-118586000D01* -X128411000Y-118584000D01* -X128413000Y-118582000D01* -X128415000Y-118580000D01* -X128417000Y-118578000D01* -X128419000Y-118576000D01* -X128421000Y-118575000D01* -X128423000Y-118573000D01* -X128425000Y-118572000D01* -X128427000Y-118570000D01* -X128430000Y-118569000D01* -X128432000Y-118568000D01* -X128435000Y-118567000D01* -X128437000Y-118567000D01* -X128440000Y-118566000D01* -X128442000Y-118566000D01* -X128445000Y-118565000D01* -X128447000Y-118565000D01* -X128450000Y-118565000D01* -X128950000Y-118565000D01* -X128953000Y-118565000D01* -X128955000Y-118565000D01* -X128958000Y-118566000D01* -X128960000Y-118566000D01* -X128963000Y-118567000D01* -X128965000Y-118567000D01* -X128968000Y-118568000D01* -X128970000Y-118569000D01* -X128973000Y-118570000D01* -X128975000Y-118572000D01* -X128977000Y-118573000D01* -X128979000Y-118575000D01* -X128981000Y-118576000D01* -X128983000Y-118578000D01* -X128985000Y-118580000D01* -X128987000Y-118582000D01* -X128989000Y-118584000D01* -X128990000Y-118586000D01* -X128992000Y-118588000D01* -X128993000Y-118590000D01* -X128995000Y-118592000D01* -X128996000Y-118595000D01* -X128997000Y-118597000D01* -X128998000Y-118600000D01* -X128998000Y-118602000D01* -X128999000Y-118605000D01* -X128999000Y-118607000D01* -X129000000Y-118610000D01* -X129000000Y-118612000D01* -X129000000Y-118615000D01* -G36* -X128958000Y-118566000D02* -G01* -X128960000Y-118566000D01* -X128963000Y-118567000D01* -X128965000Y-118567000D01* -X128968000Y-118568000D01* -X128970000Y-118569000D01* -X128973000Y-118570000D01* -X128975000Y-118572000D01* -X128977000Y-118573000D01* -X128979000Y-118575000D01* -X128981000Y-118576000D01* -X128983000Y-118578000D01* -X128985000Y-118580000D01* -X128987000Y-118582000D01* -X128989000Y-118584000D01* -X128990000Y-118586000D01* -X128992000Y-118588000D01* -X128993000Y-118590000D01* -X128995000Y-118592000D01* -X128996000Y-118595000D01* -X128997000Y-118597000D01* -X128998000Y-118600000D01* -X128998000Y-118602000D01* -X128999000Y-118605000D01* -X128999000Y-118607000D01* -X129000000Y-118610000D01* -X129000000Y-118612000D01* -X129000000Y-118615000D01* -X129000000Y-118815000D01* -X129000000Y-118818000D01* -X129000000Y-118820000D01* -X128999000Y-118823000D01* -X128999000Y-118825000D01* -X128998000Y-118828000D01* -X128998000Y-118830000D01* -X128997000Y-118833000D01* -X128996000Y-118835000D01* -X128995000Y-118838000D01* -X128993000Y-118840000D01* -X128992000Y-118842000D01* -X128990000Y-118844000D01* -X128989000Y-118846000D01* -X128987000Y-118848000D01* -X128985000Y-118850000D01* -X128983000Y-118852000D01* -X128981000Y-118854000D01* -X128979000Y-118855000D01* -X128977000Y-118857000D01* -X128975000Y-118858000D01* -X128973000Y-118860000D01* -X128970000Y-118861000D01* -X128968000Y-118862000D01* -X128965000Y-118863000D01* -X128963000Y-118863000D01* -X128960000Y-118864000D01* -X128958000Y-118864000D01* -X128955000Y-118865000D01* -X128953000Y-118865000D01* -X128950000Y-118865000D01* -X128450000Y-118865000D01* -X128447000Y-118865000D01* -X128445000Y-118865000D01* -X128442000Y-118864000D01* -X128440000Y-118864000D01* -X128437000Y-118863000D01* -X128435000Y-118863000D01* -X128432000Y-118862000D01* -X128430000Y-118861000D01* -X128427000Y-118860000D01* -X128425000Y-118858000D01* -X128423000Y-118857000D01* -X128421000Y-118855000D01* -X128419000Y-118854000D01* -X128417000Y-118852000D01* -X128415000Y-118850000D01* -X128413000Y-118848000D01* -X128411000Y-118846000D01* -X128410000Y-118844000D01* -X128408000Y-118842000D01* -X128407000Y-118840000D01* -X128405000Y-118838000D01* -X128404000Y-118835000D01* -X128403000Y-118833000D01* -X128402000Y-118830000D01* -X128402000Y-118828000D01* -X128401000Y-118825000D01* -X128401000Y-118823000D01* -X128400000Y-118820000D01* -X128400000Y-118818000D01* -X128400000Y-118815000D01* -X128400000Y-118615000D01* -X128400000Y-118612000D01* -X128400000Y-118610000D01* -X128401000Y-118607000D01* -X128401000Y-118605000D01* -X128402000Y-118602000D01* -X128402000Y-118600000D01* -X128403000Y-118597000D01* -X128404000Y-118595000D01* -X128405000Y-118592000D01* -X128407000Y-118590000D01* -X128408000Y-118588000D01* -X128410000Y-118586000D01* -X128411000Y-118584000D01* -X128413000Y-118582000D01* -X128415000Y-118580000D01* -X128417000Y-118578000D01* -X128419000Y-118576000D01* -X128421000Y-118575000D01* -X128423000Y-118573000D01* -X128425000Y-118572000D01* -X128427000Y-118570000D01* -X128430000Y-118569000D01* -X128432000Y-118568000D01* -X128435000Y-118567000D01* -X128437000Y-118567000D01* -X128440000Y-118566000D01* -X128442000Y-118566000D01* -X128445000Y-118565000D01* -X128447000Y-118565000D01* -X128450000Y-118565000D01* -X128950000Y-118565000D01* -X128953000Y-118565000D01* -X128955000Y-118565000D01* -X128958000Y-118566000D01* -G37* -X129000000Y-119015000D02* -X129000000Y-119215000D01* -X129000000Y-119218000D01* -X129000000Y-119220000D01* -X128999000Y-119223000D01* -X128999000Y-119225000D01* -X128998000Y-119228000D01* -X128998000Y-119230000D01* -X128997000Y-119233000D01* -X128996000Y-119235000D01* -X128995000Y-119238000D01* -X128993000Y-119240000D01* -X128992000Y-119242000D01* -X128990000Y-119244000D01* -X128989000Y-119246000D01* -X128987000Y-119248000D01* -X128985000Y-119250000D01* -X128983000Y-119252000D01* -X128981000Y-119254000D01* -X128979000Y-119255000D01* -X128977000Y-119257000D01* -X128975000Y-119258000D01* -X128973000Y-119260000D01* -X128970000Y-119261000D01* -X128968000Y-119262000D01* -X128965000Y-119263000D01* -X128963000Y-119263000D01* -X128960000Y-119264000D01* -X128958000Y-119264000D01* -X128955000Y-119265000D01* -X128953000Y-119265000D01* -X128950000Y-119265000D01* -X128450000Y-119265000D01* -X128447000Y-119265000D01* -X128445000Y-119265000D01* -X128442000Y-119264000D01* -X128440000Y-119264000D01* -X128437000Y-119263000D01* -X128435000Y-119263000D01* -X128432000Y-119262000D01* -X128430000Y-119261000D01* -X128427000Y-119260000D01* -X128425000Y-119258000D01* -X128423000Y-119257000D01* -X128421000Y-119255000D01* -X128419000Y-119254000D01* -X128417000Y-119252000D01* -X128415000Y-119250000D01* -X128413000Y-119248000D01* -X128411000Y-119246000D01* -X128410000Y-119244000D01* -X128408000Y-119242000D01* -X128407000Y-119240000D01* -X128405000Y-119238000D01* -X128404000Y-119235000D01* -X128403000Y-119233000D01* -X128402000Y-119230000D01* -X128402000Y-119228000D01* -X128401000Y-119225000D01* -X128401000Y-119223000D01* -X128400000Y-119220000D01* -X128400000Y-119218000D01* -X128400000Y-119215000D01* -X128400000Y-119015000D01* -X128400000Y-119012000D01* -X128400000Y-119010000D01* -X128401000Y-119007000D01* -X128401000Y-119005000D01* -X128402000Y-119002000D01* -X128402000Y-119000000D01* -X128403000Y-118997000D01* -X128404000Y-118995000D01* -X128405000Y-118992000D01* -X128407000Y-118990000D01* -X128408000Y-118988000D01* -X128410000Y-118986000D01* -X128411000Y-118984000D01* -X128413000Y-118982000D01* -X128415000Y-118980000D01* -X128417000Y-118978000D01* -X128419000Y-118976000D01* -X128421000Y-118975000D01* -X128423000Y-118973000D01* -X128425000Y-118972000D01* -X128427000Y-118970000D01* -X128430000Y-118969000D01* -X128432000Y-118968000D01* -X128435000Y-118967000D01* -X128437000Y-118967000D01* -X128440000Y-118966000D01* -X128442000Y-118966000D01* -X128445000Y-118965000D01* -X128447000Y-118965000D01* -X128450000Y-118965000D01* -X128950000Y-118965000D01* -X128953000Y-118965000D01* -X128955000Y-118965000D01* -X128958000Y-118966000D01* -X128960000Y-118966000D01* -X128963000Y-118967000D01* -X128965000Y-118967000D01* -X128968000Y-118968000D01* -X128970000Y-118969000D01* -X128973000Y-118970000D01* -X128975000Y-118972000D01* -X128977000Y-118973000D01* -X128979000Y-118975000D01* -X128981000Y-118976000D01* -X128983000Y-118978000D01* -X128985000Y-118980000D01* -X128987000Y-118982000D01* -X128989000Y-118984000D01* -X128990000Y-118986000D01* -X128992000Y-118988000D01* -X128993000Y-118990000D01* -X128995000Y-118992000D01* -X128996000Y-118995000D01* -X128997000Y-118997000D01* -X128998000Y-119000000D01* -X128998000Y-119002000D01* -X128999000Y-119005000D01* -X128999000Y-119007000D01* -X129000000Y-119010000D01* -X129000000Y-119012000D01* -X129000000Y-119015000D01* -G36* -X128958000Y-118966000D02* -G01* -X128960000Y-118966000D01* -X128963000Y-118967000D01* -X128965000Y-118967000D01* -X128968000Y-118968000D01* -X128970000Y-118969000D01* -X128973000Y-118970000D01* -X128975000Y-118972000D01* -X128977000Y-118973000D01* -X128979000Y-118975000D01* -X128981000Y-118976000D01* -X128983000Y-118978000D01* -X128985000Y-118980000D01* -X128987000Y-118982000D01* -X128989000Y-118984000D01* -X128990000Y-118986000D01* -X128992000Y-118988000D01* -X128993000Y-118990000D01* -X128995000Y-118992000D01* -X128996000Y-118995000D01* -X128997000Y-118997000D01* -X128998000Y-119000000D01* -X128998000Y-119002000D01* -X128999000Y-119005000D01* -X128999000Y-119007000D01* -X129000000Y-119010000D01* -X129000000Y-119012000D01* -X129000000Y-119015000D01* -X129000000Y-119215000D01* -X129000000Y-119218000D01* -X129000000Y-119220000D01* -X128999000Y-119223000D01* -X128999000Y-119225000D01* -X128998000Y-119228000D01* -X128998000Y-119230000D01* -X128997000Y-119233000D01* -X128996000Y-119235000D01* -X128995000Y-119238000D01* -X128993000Y-119240000D01* -X128992000Y-119242000D01* -X128990000Y-119244000D01* -X128989000Y-119246000D01* -X128987000Y-119248000D01* -X128985000Y-119250000D01* -X128983000Y-119252000D01* -X128981000Y-119254000D01* -X128979000Y-119255000D01* -X128977000Y-119257000D01* -X128975000Y-119258000D01* -X128973000Y-119260000D01* -X128970000Y-119261000D01* -X128968000Y-119262000D01* -X128965000Y-119263000D01* -X128963000Y-119263000D01* -X128960000Y-119264000D01* -X128958000Y-119264000D01* -X128955000Y-119265000D01* -X128953000Y-119265000D01* -X128950000Y-119265000D01* -X128450000Y-119265000D01* -X128447000Y-119265000D01* -X128445000Y-119265000D01* -X128442000Y-119264000D01* -X128440000Y-119264000D01* -X128437000Y-119263000D01* -X128435000Y-119263000D01* -X128432000Y-119262000D01* -X128430000Y-119261000D01* -X128427000Y-119260000D01* -X128425000Y-119258000D01* -X128423000Y-119257000D01* -X128421000Y-119255000D01* -X128419000Y-119254000D01* -X128417000Y-119252000D01* -X128415000Y-119250000D01* -X128413000Y-119248000D01* -X128411000Y-119246000D01* -X128410000Y-119244000D01* -X128408000Y-119242000D01* -X128407000Y-119240000D01* -X128405000Y-119238000D01* -X128404000Y-119235000D01* -X128403000Y-119233000D01* -X128402000Y-119230000D01* -X128402000Y-119228000D01* -X128401000Y-119225000D01* -X128401000Y-119223000D01* -X128400000Y-119220000D01* -X128400000Y-119218000D01* -X128400000Y-119215000D01* -X128400000Y-119015000D01* -X128400000Y-119012000D01* -X128400000Y-119010000D01* -X128401000Y-119007000D01* -X128401000Y-119005000D01* -X128402000Y-119002000D01* -X128402000Y-119000000D01* -X128403000Y-118997000D01* -X128404000Y-118995000D01* -X128405000Y-118992000D01* -X128407000Y-118990000D01* -X128408000Y-118988000D01* -X128410000Y-118986000D01* -X128411000Y-118984000D01* -X128413000Y-118982000D01* -X128415000Y-118980000D01* -X128417000Y-118978000D01* -X128419000Y-118976000D01* -X128421000Y-118975000D01* -X128423000Y-118973000D01* -X128425000Y-118972000D01* -X128427000Y-118970000D01* -X128430000Y-118969000D01* -X128432000Y-118968000D01* -X128435000Y-118967000D01* -X128437000Y-118967000D01* -X128440000Y-118966000D01* -X128442000Y-118966000D01* -X128445000Y-118965000D01* -X128447000Y-118965000D01* -X128450000Y-118965000D01* -X128950000Y-118965000D01* -X128953000Y-118965000D01* -X128955000Y-118965000D01* -X128958000Y-118966000D01* -G37* -X130250000Y-117615000D02* -X130250000Y-119015000D01* -X130250000Y-119020000D01* -X130249000Y-119025000D01* -X130249000Y-119031000D01* -X130248000Y-119036000D01* -X130247000Y-119041000D01* -X130245000Y-119046000D01* -X130243000Y-119051000D01* -X130241000Y-119056000D01* -X130239000Y-119060000D01* -X130237000Y-119065000D01* -X130234000Y-119069000D01* -X130231000Y-119074000D01* -X130228000Y-119078000D01* -X130224000Y-119082000D01* -X130221000Y-119086000D01* -X130217000Y-119089000D01* -X130213000Y-119093000D01* -X130209000Y-119096000D01* -X130204000Y-119099000D01* -X130200000Y-119102000D01* -X130195000Y-119104000D01* -X130191000Y-119106000D01* -X130186000Y-119108000D01* -X130181000Y-119110000D01* -X130176000Y-119112000D01* -X130171000Y-119113000D01* -X130166000Y-119114000D01* -X130160000Y-119114000D01* -X130155000Y-119115000D01* -X130150000Y-119115000D01* -X129350000Y-119115000D01* -X129345000Y-119115000D01* -X129340000Y-119114000D01* -X129334000Y-119114000D01* -X129329000Y-119113000D01* -X129324000Y-119112000D01* -X129319000Y-119110000D01* -X129314000Y-119108000D01* -X129309000Y-119106000D01* -X129305000Y-119104000D01* -X129300000Y-119102000D01* -X129296000Y-119099000D01* -X129291000Y-119096000D01* -X129287000Y-119093000D01* -X129283000Y-119089000D01* -X129279000Y-119086000D01* -X129276000Y-119082000D01* -X129272000Y-119078000D01* -X129269000Y-119074000D01* -X129266000Y-119069000D01* -X129263000Y-119065000D01* -X129261000Y-119060000D01* -X129259000Y-119056000D01* -X129257000Y-119051000D01* -X129255000Y-119046000D01* -X129253000Y-119041000D01* -X129252000Y-119036000D01* -X129251000Y-119031000D01* -X129251000Y-119025000D01* -X129250000Y-119020000D01* -X129250000Y-119015000D01* -X129250000Y-117615000D01* -X129250000Y-117610000D01* -X129251000Y-117605000D01* -X129251000Y-117599000D01* -X129252000Y-117594000D01* -X129253000Y-117589000D01* -X129255000Y-117584000D01* -X129257000Y-117579000D01* -X129259000Y-117574000D01* -X129261000Y-117570000D01* -X129263000Y-117565000D01* -X129266000Y-117561000D01* -X129269000Y-117556000D01* -X129272000Y-117552000D01* -X129276000Y-117548000D01* -X129279000Y-117544000D01* -X129283000Y-117541000D01* -X129287000Y-117537000D01* -X129291000Y-117534000D01* -X129296000Y-117531000D01* -X129300000Y-117528000D01* -X129305000Y-117526000D01* -X129309000Y-117524000D01* -X129314000Y-117522000D01* -X129319000Y-117520000D01* -X129324000Y-117518000D01* -X129329000Y-117517000D01* -X129334000Y-117516000D01* -X129340000Y-117516000D01* -X129345000Y-117515000D01* -X129350000Y-117515000D01* -X130150000Y-117515000D01* -X130155000Y-117515000D01* -X130160000Y-117516000D01* -X130166000Y-117516000D01* -X130171000Y-117517000D01* -X130176000Y-117518000D01* -X130181000Y-117520000D01* -X130186000Y-117522000D01* -X130191000Y-117524000D01* -X130195000Y-117526000D01* -X130200000Y-117528000D01* -X130204000Y-117531000D01* -X130209000Y-117534000D01* -X130213000Y-117537000D01* -X130217000Y-117541000D01* -X130221000Y-117544000D01* -X130224000Y-117548000D01* -X130228000Y-117552000D01* -X130231000Y-117556000D01* -X130234000Y-117561000D01* -X130237000Y-117565000D01* -X130239000Y-117570000D01* -X130241000Y-117574000D01* -X130243000Y-117579000D01* -X130245000Y-117584000D01* -X130247000Y-117589000D01* -X130248000Y-117594000D01* -X130249000Y-117599000D01* -X130249000Y-117605000D01* -X130250000Y-117610000D01* -X130250000Y-117615000D01* -G36* -X130160000Y-117516000D02* -G01* -X130166000Y-117516000D01* -X130171000Y-117517000D01* -X130176000Y-117518000D01* -X130181000Y-117520000D01* -X130186000Y-117522000D01* -X130191000Y-117524000D01* -X130195000Y-117526000D01* -X130200000Y-117528000D01* -X130204000Y-117531000D01* -X130209000Y-117534000D01* -X130213000Y-117537000D01* -X130217000Y-117541000D01* -X130221000Y-117544000D01* -X130224000Y-117548000D01* -X130228000Y-117552000D01* -X130231000Y-117556000D01* -X130234000Y-117561000D01* -X130237000Y-117565000D01* -X130239000Y-117570000D01* -X130241000Y-117574000D01* -X130243000Y-117579000D01* -X130245000Y-117584000D01* -X130247000Y-117589000D01* -X130248000Y-117594000D01* -X130249000Y-117599000D01* -X130249000Y-117605000D01* -X130250000Y-117610000D01* -X130250000Y-117615000D01* -X130250000Y-119015000D01* -X130250000Y-119020000D01* -X130249000Y-119025000D01* -X130249000Y-119031000D01* -X130248000Y-119036000D01* -X130247000Y-119041000D01* -X130245000Y-119046000D01* -X130243000Y-119051000D01* -X130241000Y-119056000D01* -X130239000Y-119060000D01* -X130237000Y-119065000D01* -X130234000Y-119069000D01* -X130231000Y-119074000D01* -X130228000Y-119078000D01* -X130224000Y-119082000D01* -X130221000Y-119086000D01* -X130217000Y-119089000D01* -X130213000Y-119093000D01* -X130209000Y-119096000D01* -X130204000Y-119099000D01* -X130200000Y-119102000D01* -X130195000Y-119104000D01* -X130191000Y-119106000D01* -X130186000Y-119108000D01* -X130181000Y-119110000D01* -X130176000Y-119112000D01* -X130171000Y-119113000D01* -X130166000Y-119114000D01* -X130160000Y-119114000D01* -X130155000Y-119115000D01* -X130150000Y-119115000D01* -X129350000Y-119115000D01* -X129345000Y-119115000D01* -X129340000Y-119114000D01* -X129334000Y-119114000D01* -X129329000Y-119113000D01* -X129324000Y-119112000D01* -X129319000Y-119110000D01* -X129314000Y-119108000D01* -X129309000Y-119106000D01* -X129305000Y-119104000D01* -X129300000Y-119102000D01* -X129296000Y-119099000D01* -X129291000Y-119096000D01* -X129287000Y-119093000D01* -X129283000Y-119089000D01* -X129279000Y-119086000D01* -X129276000Y-119082000D01* -X129272000Y-119078000D01* -X129269000Y-119074000D01* -X129266000Y-119069000D01* -X129263000Y-119065000D01* -X129261000Y-119060000D01* -X129259000Y-119056000D01* -X129257000Y-119051000D01* -X129255000Y-119046000D01* -X129253000Y-119041000D01* -X129252000Y-119036000D01* -X129251000Y-119031000D01* -X129251000Y-119025000D01* -X129250000Y-119020000D01* -X129250000Y-119015000D01* -X129250000Y-117615000D01* -X129250000Y-117610000D01* -X129251000Y-117605000D01* -X129251000Y-117599000D01* -X129252000Y-117594000D01* -X129253000Y-117589000D01* -X129255000Y-117584000D01* -X129257000Y-117579000D01* -X129259000Y-117574000D01* -X129261000Y-117570000D01* -X129263000Y-117565000D01* -X129266000Y-117561000D01* -X129269000Y-117556000D01* -X129272000Y-117552000D01* -X129276000Y-117548000D01* -X129279000Y-117544000D01* -X129283000Y-117541000D01* -X129287000Y-117537000D01* -X129291000Y-117534000D01* -X129296000Y-117531000D01* -X129300000Y-117528000D01* -X129305000Y-117526000D01* -X129309000Y-117524000D01* -X129314000Y-117522000D01* -X129319000Y-117520000D01* -X129324000Y-117518000D01* -X129329000Y-117517000D01* -X129334000Y-117516000D01* -X129340000Y-117516000D01* -X129345000Y-117515000D01* -X129350000Y-117515000D01* -X130150000Y-117515000D01* -X130155000Y-117515000D01* -X130160000Y-117516000D01* -G37* -X131100000Y-117415000D02* -X131100000Y-117615000D01* -X131100000Y-117618000D01* -X131100000Y-117620000D01* -X131099000Y-117623000D01* -X131099000Y-117625000D01* -X131098000Y-117628000D01* -X131098000Y-117630000D01* -X131097000Y-117633000D01* -X131096000Y-117635000D01* -X131095000Y-117638000D01* -X131093000Y-117640000D01* -X131092000Y-117642000D01* -X131090000Y-117644000D01* -X131089000Y-117646000D01* -X131087000Y-117648000D01* -X131085000Y-117650000D01* -X131083000Y-117652000D01* -X131081000Y-117654000D01* -X131079000Y-117655000D01* -X131077000Y-117657000D01* -X131075000Y-117658000D01* -X131073000Y-117660000D01* -X131070000Y-117661000D01* -X131068000Y-117662000D01* -X131065000Y-117663000D01* -X131063000Y-117663000D01* -X131060000Y-117664000D01* -X131058000Y-117664000D01* -X131055000Y-117665000D01* -X131053000Y-117665000D01* -X131050000Y-117665000D01* -X130550000Y-117665000D01* -X130547000Y-117665000D01* -X130545000Y-117665000D01* -X130542000Y-117664000D01* -X130540000Y-117664000D01* -X130537000Y-117663000D01* -X130535000Y-117663000D01* -X130532000Y-117662000D01* -X130530000Y-117661000D01* -X130527000Y-117660000D01* -X130525000Y-117658000D01* -X130523000Y-117657000D01* -X130521000Y-117655000D01* -X130519000Y-117654000D01* -X130517000Y-117652000D01* -X130515000Y-117650000D01* -X130513000Y-117648000D01* -X130511000Y-117646000D01* -X130510000Y-117644000D01* -X130508000Y-117642000D01* -X130507000Y-117640000D01* -X130505000Y-117638000D01* -X130504000Y-117635000D01* -X130503000Y-117633000D01* -X130502000Y-117630000D01* -X130502000Y-117628000D01* -X130501000Y-117625000D01* -X130501000Y-117623000D01* -X130500000Y-117620000D01* -X130500000Y-117618000D01* -X130500000Y-117615000D01* -X130500000Y-117415000D01* -X130500000Y-117412000D01* -X130500000Y-117410000D01* -X130501000Y-117407000D01* -X130501000Y-117405000D01* -X130502000Y-117402000D01* -X130502000Y-117400000D01* -X130503000Y-117397000D01* -X130504000Y-117395000D01* -X130505000Y-117392000D01* -X130507000Y-117390000D01* -X130508000Y-117388000D01* -X130510000Y-117386000D01* -X130511000Y-117384000D01* -X130513000Y-117382000D01* -X130515000Y-117380000D01* -X130517000Y-117378000D01* -X130519000Y-117376000D01* -X130521000Y-117375000D01* -X130523000Y-117373000D01* -X130525000Y-117372000D01* -X130527000Y-117370000D01* -X130530000Y-117369000D01* -X130532000Y-117368000D01* -X130535000Y-117367000D01* -X130537000Y-117367000D01* -X130540000Y-117366000D01* -X130542000Y-117366000D01* -X130545000Y-117365000D01* -X130547000Y-117365000D01* -X130550000Y-117365000D01* -X131050000Y-117365000D01* -X131053000Y-117365000D01* -X131055000Y-117365000D01* -X131058000Y-117366000D01* -X131060000Y-117366000D01* -X131063000Y-117367000D01* -X131065000Y-117367000D01* -X131068000Y-117368000D01* -X131070000Y-117369000D01* -X131073000Y-117370000D01* -X131075000Y-117372000D01* -X131077000Y-117373000D01* -X131079000Y-117375000D01* -X131081000Y-117376000D01* -X131083000Y-117378000D01* -X131085000Y-117380000D01* -X131087000Y-117382000D01* -X131089000Y-117384000D01* -X131090000Y-117386000D01* -X131092000Y-117388000D01* -X131093000Y-117390000D01* -X131095000Y-117392000D01* -X131096000Y-117395000D01* -X131097000Y-117397000D01* -X131098000Y-117400000D01* -X131098000Y-117402000D01* -X131099000Y-117405000D01* -X131099000Y-117407000D01* -X131100000Y-117410000D01* -X131100000Y-117412000D01* -X131100000Y-117415000D01* -G36* -X131058000Y-117366000D02* -G01* -X131060000Y-117366000D01* -X131063000Y-117367000D01* -X131065000Y-117367000D01* -X131068000Y-117368000D01* -X131070000Y-117369000D01* -X131073000Y-117370000D01* -X131075000Y-117372000D01* -X131077000Y-117373000D01* -X131079000Y-117375000D01* -X131081000Y-117376000D01* -X131083000Y-117378000D01* -X131085000Y-117380000D01* -X131087000Y-117382000D01* -X131089000Y-117384000D01* -X131090000Y-117386000D01* -X131092000Y-117388000D01* -X131093000Y-117390000D01* -X131095000Y-117392000D01* -X131096000Y-117395000D01* -X131097000Y-117397000D01* -X131098000Y-117400000D01* -X131098000Y-117402000D01* -X131099000Y-117405000D01* -X131099000Y-117407000D01* -X131100000Y-117410000D01* -X131100000Y-117412000D01* -X131100000Y-117415000D01* -X131100000Y-117615000D01* -X131100000Y-117618000D01* -X131100000Y-117620000D01* -X131099000Y-117623000D01* -X131099000Y-117625000D01* -X131098000Y-117628000D01* -X131098000Y-117630000D01* -X131097000Y-117633000D01* -X131096000Y-117635000D01* -X131095000Y-117638000D01* -X131093000Y-117640000D01* -X131092000Y-117642000D01* -X131090000Y-117644000D01* -X131089000Y-117646000D01* -X131087000Y-117648000D01* -X131085000Y-117650000D01* -X131083000Y-117652000D01* -X131081000Y-117654000D01* -X131079000Y-117655000D01* -X131077000Y-117657000D01* -X131075000Y-117658000D01* -X131073000Y-117660000D01* -X131070000Y-117661000D01* -X131068000Y-117662000D01* -X131065000Y-117663000D01* -X131063000Y-117663000D01* -X131060000Y-117664000D01* -X131058000Y-117664000D01* -X131055000Y-117665000D01* -X131053000Y-117665000D01* -X131050000Y-117665000D01* -X130550000Y-117665000D01* -X130547000Y-117665000D01* -X130545000Y-117665000D01* -X130542000Y-117664000D01* -X130540000Y-117664000D01* -X130537000Y-117663000D01* -X130535000Y-117663000D01* -X130532000Y-117662000D01* -X130530000Y-117661000D01* -X130527000Y-117660000D01* -X130525000Y-117658000D01* -X130523000Y-117657000D01* -X130521000Y-117655000D01* -X130519000Y-117654000D01* -X130517000Y-117652000D01* -X130515000Y-117650000D01* -X130513000Y-117648000D01* -X130511000Y-117646000D01* -X130510000Y-117644000D01* -X130508000Y-117642000D01* -X130507000Y-117640000D01* -X130505000Y-117638000D01* -X130504000Y-117635000D01* -X130503000Y-117633000D01* -X130502000Y-117630000D01* -X130502000Y-117628000D01* -X130501000Y-117625000D01* -X130501000Y-117623000D01* -X130500000Y-117620000D01* -X130500000Y-117618000D01* -X130500000Y-117615000D01* -X130500000Y-117415000D01* -X130500000Y-117412000D01* -X130500000Y-117410000D01* -X130501000Y-117407000D01* -X130501000Y-117405000D01* -X130502000Y-117402000D01* -X130502000Y-117400000D01* -X130503000Y-117397000D01* -X130504000Y-117395000D01* -X130505000Y-117392000D01* -X130507000Y-117390000D01* -X130508000Y-117388000D01* -X130510000Y-117386000D01* -X130511000Y-117384000D01* -X130513000Y-117382000D01* -X130515000Y-117380000D01* -X130517000Y-117378000D01* -X130519000Y-117376000D01* -X130521000Y-117375000D01* -X130523000Y-117373000D01* -X130525000Y-117372000D01* -X130527000Y-117370000D01* -X130530000Y-117369000D01* -X130532000Y-117368000D01* -X130535000Y-117367000D01* -X130537000Y-117367000D01* -X130540000Y-117366000D01* -X130542000Y-117366000D01* -X130545000Y-117365000D01* -X130547000Y-117365000D01* -X130550000Y-117365000D01* -X131050000Y-117365000D01* -X131053000Y-117365000D01* -X131055000Y-117365000D01* -X131058000Y-117366000D01* -G37* -X131100000Y-117815000D02* -X131100000Y-118015000D01* -X131100000Y-118018000D01* -X131100000Y-118020000D01* -X131099000Y-118023000D01* -X131099000Y-118025000D01* -X131098000Y-118028000D01* -X131098000Y-118030000D01* -X131097000Y-118033000D01* -X131096000Y-118035000D01* -X131095000Y-118038000D01* -X131093000Y-118040000D01* -X131092000Y-118042000D01* -X131090000Y-118044000D01* -X131089000Y-118046000D01* -X131087000Y-118048000D01* -X131085000Y-118050000D01* -X131083000Y-118052000D01* -X131081000Y-118054000D01* -X131079000Y-118055000D01* -X131077000Y-118057000D01* -X131075000Y-118058000D01* -X131073000Y-118060000D01* -X131070000Y-118061000D01* -X131068000Y-118062000D01* -X131065000Y-118063000D01* -X131063000Y-118063000D01* -X131060000Y-118064000D01* -X131058000Y-118064000D01* -X131055000Y-118065000D01* -X131053000Y-118065000D01* -X131050000Y-118065000D01* -X130550000Y-118065000D01* -X130547000Y-118065000D01* -X130545000Y-118065000D01* -X130542000Y-118064000D01* -X130540000Y-118064000D01* -X130537000Y-118063000D01* -X130535000Y-118063000D01* -X130532000Y-118062000D01* -X130530000Y-118061000D01* -X130527000Y-118060000D01* -X130525000Y-118058000D01* -X130523000Y-118057000D01* -X130521000Y-118055000D01* -X130519000Y-118054000D01* -X130517000Y-118052000D01* -X130515000Y-118050000D01* -X130513000Y-118048000D01* -X130511000Y-118046000D01* -X130510000Y-118044000D01* -X130508000Y-118042000D01* -X130507000Y-118040000D01* -X130505000Y-118038000D01* -X130504000Y-118035000D01* -X130503000Y-118033000D01* -X130502000Y-118030000D01* -X130502000Y-118028000D01* -X130501000Y-118025000D01* -X130501000Y-118023000D01* -X130500000Y-118020000D01* -X130500000Y-118018000D01* -X130500000Y-118015000D01* -X130500000Y-117815000D01* -X130500000Y-117812000D01* -X130500000Y-117810000D01* -X130501000Y-117807000D01* -X130501000Y-117805000D01* -X130502000Y-117802000D01* -X130502000Y-117800000D01* -X130503000Y-117797000D01* -X130504000Y-117795000D01* -X130505000Y-117792000D01* -X130507000Y-117790000D01* -X130508000Y-117788000D01* -X130510000Y-117786000D01* -X130511000Y-117784000D01* -X130513000Y-117782000D01* -X130515000Y-117780000D01* -X130517000Y-117778000D01* -X130519000Y-117776000D01* -X130521000Y-117775000D01* -X130523000Y-117773000D01* -X130525000Y-117772000D01* -X130527000Y-117770000D01* -X130530000Y-117769000D01* -X130532000Y-117768000D01* -X130535000Y-117767000D01* -X130537000Y-117767000D01* -X130540000Y-117766000D01* -X130542000Y-117766000D01* -X130545000Y-117765000D01* -X130547000Y-117765000D01* -X130550000Y-117765000D01* -X131050000Y-117765000D01* -X131053000Y-117765000D01* -X131055000Y-117765000D01* -X131058000Y-117766000D01* -X131060000Y-117766000D01* -X131063000Y-117767000D01* -X131065000Y-117767000D01* -X131068000Y-117768000D01* -X131070000Y-117769000D01* -X131073000Y-117770000D01* -X131075000Y-117772000D01* -X131077000Y-117773000D01* -X131079000Y-117775000D01* -X131081000Y-117776000D01* -X131083000Y-117778000D01* -X131085000Y-117780000D01* -X131087000Y-117782000D01* -X131089000Y-117784000D01* -X131090000Y-117786000D01* -X131092000Y-117788000D01* -X131093000Y-117790000D01* -X131095000Y-117792000D01* -X131096000Y-117795000D01* -X131097000Y-117797000D01* -X131098000Y-117800000D01* -X131098000Y-117802000D01* -X131099000Y-117805000D01* -X131099000Y-117807000D01* -X131100000Y-117810000D01* -X131100000Y-117812000D01* -X131100000Y-117815000D01* -G36* -X131058000Y-117766000D02* -G01* -X131060000Y-117766000D01* -X131063000Y-117767000D01* -X131065000Y-117767000D01* -X131068000Y-117768000D01* -X131070000Y-117769000D01* -X131073000Y-117770000D01* -X131075000Y-117772000D01* -X131077000Y-117773000D01* -X131079000Y-117775000D01* -X131081000Y-117776000D01* -X131083000Y-117778000D01* -X131085000Y-117780000D01* -X131087000Y-117782000D01* -X131089000Y-117784000D01* -X131090000Y-117786000D01* -X131092000Y-117788000D01* -X131093000Y-117790000D01* -X131095000Y-117792000D01* -X131096000Y-117795000D01* -X131097000Y-117797000D01* -X131098000Y-117800000D01* -X131098000Y-117802000D01* -X131099000Y-117805000D01* -X131099000Y-117807000D01* -X131100000Y-117810000D01* -X131100000Y-117812000D01* -X131100000Y-117815000D01* -X131100000Y-118015000D01* -X131100000Y-118018000D01* -X131100000Y-118020000D01* -X131099000Y-118023000D01* -X131099000Y-118025000D01* -X131098000Y-118028000D01* -X131098000Y-118030000D01* -X131097000Y-118033000D01* -X131096000Y-118035000D01* -X131095000Y-118038000D01* -X131093000Y-118040000D01* -X131092000Y-118042000D01* -X131090000Y-118044000D01* -X131089000Y-118046000D01* -X131087000Y-118048000D01* -X131085000Y-118050000D01* -X131083000Y-118052000D01* -X131081000Y-118054000D01* -X131079000Y-118055000D01* -X131077000Y-118057000D01* -X131075000Y-118058000D01* -X131073000Y-118060000D01* -X131070000Y-118061000D01* -X131068000Y-118062000D01* -X131065000Y-118063000D01* -X131063000Y-118063000D01* -X131060000Y-118064000D01* -X131058000Y-118064000D01* -X131055000Y-118065000D01* -X131053000Y-118065000D01* -X131050000Y-118065000D01* -X130550000Y-118065000D01* -X130547000Y-118065000D01* -X130545000Y-118065000D01* -X130542000Y-118064000D01* -X130540000Y-118064000D01* -X130537000Y-118063000D01* -X130535000Y-118063000D01* -X130532000Y-118062000D01* -X130530000Y-118061000D01* -X130527000Y-118060000D01* -X130525000Y-118058000D01* -X130523000Y-118057000D01* -X130521000Y-118055000D01* -X130519000Y-118054000D01* -X130517000Y-118052000D01* -X130515000Y-118050000D01* -X130513000Y-118048000D01* -X130511000Y-118046000D01* -X130510000Y-118044000D01* -X130508000Y-118042000D01* -X130507000Y-118040000D01* -X130505000Y-118038000D01* -X130504000Y-118035000D01* -X130503000Y-118033000D01* -X130502000Y-118030000D01* -X130502000Y-118028000D01* -X130501000Y-118025000D01* -X130501000Y-118023000D01* -X130500000Y-118020000D01* -X130500000Y-118018000D01* -X130500000Y-118015000D01* -X130500000Y-117815000D01* -X130500000Y-117812000D01* -X130500000Y-117810000D01* -X130501000Y-117807000D01* -X130501000Y-117805000D01* -X130502000Y-117802000D01* -X130502000Y-117800000D01* -X130503000Y-117797000D01* -X130504000Y-117795000D01* -X130505000Y-117792000D01* -X130507000Y-117790000D01* -X130508000Y-117788000D01* -X130510000Y-117786000D01* -X130511000Y-117784000D01* -X130513000Y-117782000D01* -X130515000Y-117780000D01* -X130517000Y-117778000D01* -X130519000Y-117776000D01* -X130521000Y-117775000D01* -X130523000Y-117773000D01* -X130525000Y-117772000D01* -X130527000Y-117770000D01* -X130530000Y-117769000D01* -X130532000Y-117768000D01* -X130535000Y-117767000D01* -X130537000Y-117767000D01* -X130540000Y-117766000D01* -X130542000Y-117766000D01* -X130545000Y-117765000D01* -X130547000Y-117765000D01* -X130550000Y-117765000D01* -X131050000Y-117765000D01* -X131053000Y-117765000D01* -X131055000Y-117765000D01* -X131058000Y-117766000D01* -G37* -X131100000Y-118215000D02* -X131100000Y-118415000D01* -X131100000Y-118418000D01* -X131100000Y-118420000D01* -X131099000Y-118423000D01* -X131099000Y-118425000D01* -X131098000Y-118428000D01* -X131098000Y-118430000D01* -X131097000Y-118433000D01* -X131096000Y-118435000D01* -X131095000Y-118438000D01* -X131093000Y-118440000D01* -X131092000Y-118442000D01* -X131090000Y-118444000D01* -X131089000Y-118446000D01* -X131087000Y-118448000D01* -X131085000Y-118450000D01* -X131083000Y-118452000D01* -X131081000Y-118454000D01* -X131079000Y-118455000D01* -X131077000Y-118457000D01* -X131075000Y-118458000D01* -X131073000Y-118460000D01* -X131070000Y-118461000D01* -X131068000Y-118462000D01* -X131065000Y-118463000D01* -X131063000Y-118463000D01* -X131060000Y-118464000D01* -X131058000Y-118464000D01* -X131055000Y-118465000D01* -X131053000Y-118465000D01* -X131050000Y-118465000D01* -X130550000Y-118465000D01* -X130547000Y-118465000D01* -X130545000Y-118465000D01* -X130542000Y-118464000D01* -X130540000Y-118464000D01* -X130537000Y-118463000D01* -X130535000Y-118463000D01* -X130532000Y-118462000D01* -X130530000Y-118461000D01* -X130527000Y-118460000D01* -X130525000Y-118458000D01* -X130523000Y-118457000D01* -X130521000Y-118455000D01* -X130519000Y-118454000D01* -X130517000Y-118452000D01* -X130515000Y-118450000D01* -X130513000Y-118448000D01* -X130511000Y-118446000D01* -X130510000Y-118444000D01* -X130508000Y-118442000D01* -X130507000Y-118440000D01* -X130505000Y-118438000D01* -X130504000Y-118435000D01* -X130503000Y-118433000D01* -X130502000Y-118430000D01* -X130502000Y-118428000D01* -X130501000Y-118425000D01* -X130501000Y-118423000D01* -X130500000Y-118420000D01* -X130500000Y-118418000D01* -X130500000Y-118415000D01* -X130500000Y-118215000D01* -X130500000Y-118212000D01* -X130500000Y-118210000D01* -X130501000Y-118207000D01* -X130501000Y-118205000D01* -X130502000Y-118202000D01* -X130502000Y-118200000D01* -X130503000Y-118197000D01* -X130504000Y-118195000D01* -X130505000Y-118192000D01* -X130507000Y-118190000D01* -X130508000Y-118188000D01* -X130510000Y-118186000D01* -X130511000Y-118184000D01* -X130513000Y-118182000D01* -X130515000Y-118180000D01* -X130517000Y-118178000D01* -X130519000Y-118176000D01* -X130521000Y-118175000D01* -X130523000Y-118173000D01* -X130525000Y-118172000D01* -X130527000Y-118170000D01* -X130530000Y-118169000D01* -X130532000Y-118168000D01* -X130535000Y-118167000D01* -X130537000Y-118167000D01* -X130540000Y-118166000D01* -X130542000Y-118166000D01* -X130545000Y-118165000D01* -X130547000Y-118165000D01* -X130550000Y-118165000D01* -X131050000Y-118165000D01* -X131053000Y-118165000D01* -X131055000Y-118165000D01* -X131058000Y-118166000D01* -X131060000Y-118166000D01* -X131063000Y-118167000D01* -X131065000Y-118167000D01* -X131068000Y-118168000D01* -X131070000Y-118169000D01* -X131073000Y-118170000D01* -X131075000Y-118172000D01* -X131077000Y-118173000D01* -X131079000Y-118175000D01* -X131081000Y-118176000D01* -X131083000Y-118178000D01* -X131085000Y-118180000D01* -X131087000Y-118182000D01* -X131089000Y-118184000D01* -X131090000Y-118186000D01* -X131092000Y-118188000D01* -X131093000Y-118190000D01* -X131095000Y-118192000D01* -X131096000Y-118195000D01* -X131097000Y-118197000D01* -X131098000Y-118200000D01* -X131098000Y-118202000D01* -X131099000Y-118205000D01* -X131099000Y-118207000D01* -X131100000Y-118210000D01* -X131100000Y-118212000D01* -X131100000Y-118215000D01* -G36* -X131058000Y-118166000D02* -G01* -X131060000Y-118166000D01* -X131063000Y-118167000D01* -X131065000Y-118167000D01* -X131068000Y-118168000D01* -X131070000Y-118169000D01* -X131073000Y-118170000D01* -X131075000Y-118172000D01* -X131077000Y-118173000D01* -X131079000Y-118175000D01* -X131081000Y-118176000D01* -X131083000Y-118178000D01* -X131085000Y-118180000D01* -X131087000Y-118182000D01* -X131089000Y-118184000D01* -X131090000Y-118186000D01* -X131092000Y-118188000D01* -X131093000Y-118190000D01* -X131095000Y-118192000D01* -X131096000Y-118195000D01* -X131097000Y-118197000D01* -X131098000Y-118200000D01* -X131098000Y-118202000D01* -X131099000Y-118205000D01* -X131099000Y-118207000D01* -X131100000Y-118210000D01* -X131100000Y-118212000D01* -X131100000Y-118215000D01* -X131100000Y-118415000D01* -X131100000Y-118418000D01* -X131100000Y-118420000D01* -X131099000Y-118423000D01* -X131099000Y-118425000D01* -X131098000Y-118428000D01* -X131098000Y-118430000D01* -X131097000Y-118433000D01* -X131096000Y-118435000D01* -X131095000Y-118438000D01* -X131093000Y-118440000D01* -X131092000Y-118442000D01* -X131090000Y-118444000D01* -X131089000Y-118446000D01* -X131087000Y-118448000D01* -X131085000Y-118450000D01* -X131083000Y-118452000D01* -X131081000Y-118454000D01* -X131079000Y-118455000D01* -X131077000Y-118457000D01* -X131075000Y-118458000D01* -X131073000Y-118460000D01* -X131070000Y-118461000D01* -X131068000Y-118462000D01* -X131065000Y-118463000D01* -X131063000Y-118463000D01* -X131060000Y-118464000D01* -X131058000Y-118464000D01* -X131055000Y-118465000D01* -X131053000Y-118465000D01* -X131050000Y-118465000D01* -X130550000Y-118465000D01* -X130547000Y-118465000D01* -X130545000Y-118465000D01* -X130542000Y-118464000D01* -X130540000Y-118464000D01* -X130537000Y-118463000D01* -X130535000Y-118463000D01* -X130532000Y-118462000D01* -X130530000Y-118461000D01* -X130527000Y-118460000D01* -X130525000Y-118458000D01* -X130523000Y-118457000D01* -X130521000Y-118455000D01* -X130519000Y-118454000D01* -X130517000Y-118452000D01* -X130515000Y-118450000D01* -X130513000Y-118448000D01* -X130511000Y-118446000D01* -X130510000Y-118444000D01* -X130508000Y-118442000D01* -X130507000Y-118440000D01* -X130505000Y-118438000D01* -X130504000Y-118435000D01* -X130503000Y-118433000D01* -X130502000Y-118430000D01* -X130502000Y-118428000D01* -X130501000Y-118425000D01* -X130501000Y-118423000D01* -X130500000Y-118420000D01* -X130500000Y-118418000D01* -X130500000Y-118415000D01* -X130500000Y-118215000D01* -X130500000Y-118212000D01* -X130500000Y-118210000D01* -X130501000Y-118207000D01* -X130501000Y-118205000D01* -X130502000Y-118202000D01* -X130502000Y-118200000D01* -X130503000Y-118197000D01* -X130504000Y-118195000D01* -X130505000Y-118192000D01* -X130507000Y-118190000D01* -X130508000Y-118188000D01* -X130510000Y-118186000D01* -X130511000Y-118184000D01* -X130513000Y-118182000D01* -X130515000Y-118180000D01* -X130517000Y-118178000D01* -X130519000Y-118176000D01* -X130521000Y-118175000D01* -X130523000Y-118173000D01* -X130525000Y-118172000D01* -X130527000Y-118170000D01* -X130530000Y-118169000D01* -X130532000Y-118168000D01* -X130535000Y-118167000D01* -X130537000Y-118167000D01* -X130540000Y-118166000D01* -X130542000Y-118166000D01* -X130545000Y-118165000D01* -X130547000Y-118165000D01* -X130550000Y-118165000D01* -X131050000Y-118165000D01* -X131053000Y-118165000D01* -X131055000Y-118165000D01* -X131058000Y-118166000D01* -G37* -X131100000Y-118615000D02* -X131100000Y-118815000D01* -X131100000Y-118818000D01* -X131100000Y-118820000D01* -X131099000Y-118823000D01* -X131099000Y-118825000D01* -X131098000Y-118828000D01* -X131098000Y-118830000D01* -X131097000Y-118833000D01* -X131096000Y-118835000D01* -X131095000Y-118838000D01* -X131093000Y-118840000D01* -X131092000Y-118842000D01* -X131090000Y-118844000D01* -X131089000Y-118846000D01* -X131087000Y-118848000D01* -X131085000Y-118850000D01* -X131083000Y-118852000D01* -X131081000Y-118854000D01* -X131079000Y-118855000D01* -X131077000Y-118857000D01* -X131075000Y-118858000D01* -X131073000Y-118860000D01* -X131070000Y-118861000D01* -X131068000Y-118862000D01* -X131065000Y-118863000D01* -X131063000Y-118863000D01* -X131060000Y-118864000D01* -X131058000Y-118864000D01* -X131055000Y-118865000D01* -X131053000Y-118865000D01* -X131050000Y-118865000D01* -X130550000Y-118865000D01* -X130547000Y-118865000D01* -X130545000Y-118865000D01* -X130542000Y-118864000D01* -X130540000Y-118864000D01* -X130537000Y-118863000D01* -X130535000Y-118863000D01* -X130532000Y-118862000D01* -X130530000Y-118861000D01* -X130527000Y-118860000D01* -X130525000Y-118858000D01* -X130523000Y-118857000D01* -X130521000Y-118855000D01* -X130519000Y-118854000D01* -X130517000Y-118852000D01* -X130515000Y-118850000D01* -X130513000Y-118848000D01* -X130511000Y-118846000D01* -X130510000Y-118844000D01* -X130508000Y-118842000D01* -X130507000Y-118840000D01* -X130505000Y-118838000D01* -X130504000Y-118835000D01* -X130503000Y-118833000D01* -X130502000Y-118830000D01* -X130502000Y-118828000D01* -X130501000Y-118825000D01* -X130501000Y-118823000D01* -X130500000Y-118820000D01* -X130500000Y-118818000D01* -X130500000Y-118815000D01* -X130500000Y-118615000D01* -X130500000Y-118612000D01* -X130500000Y-118610000D01* -X130501000Y-118607000D01* -X130501000Y-118605000D01* -X130502000Y-118602000D01* -X130502000Y-118600000D01* -X130503000Y-118597000D01* -X130504000Y-118595000D01* -X130505000Y-118592000D01* -X130507000Y-118590000D01* -X130508000Y-118588000D01* -X130510000Y-118586000D01* -X130511000Y-118584000D01* -X130513000Y-118582000D01* -X130515000Y-118580000D01* -X130517000Y-118578000D01* -X130519000Y-118576000D01* -X130521000Y-118575000D01* -X130523000Y-118573000D01* -X130525000Y-118572000D01* -X130527000Y-118570000D01* -X130530000Y-118569000D01* -X130532000Y-118568000D01* -X130535000Y-118567000D01* -X130537000Y-118567000D01* -X130540000Y-118566000D01* -X130542000Y-118566000D01* -X130545000Y-118565000D01* -X130547000Y-118565000D01* -X130550000Y-118565000D01* -X131050000Y-118565000D01* -X131053000Y-118565000D01* -X131055000Y-118565000D01* -X131058000Y-118566000D01* -X131060000Y-118566000D01* -X131063000Y-118567000D01* -X131065000Y-118567000D01* -X131068000Y-118568000D01* -X131070000Y-118569000D01* -X131073000Y-118570000D01* -X131075000Y-118572000D01* -X131077000Y-118573000D01* -X131079000Y-118575000D01* -X131081000Y-118576000D01* -X131083000Y-118578000D01* -X131085000Y-118580000D01* -X131087000Y-118582000D01* -X131089000Y-118584000D01* -X131090000Y-118586000D01* -X131092000Y-118588000D01* -X131093000Y-118590000D01* -X131095000Y-118592000D01* -X131096000Y-118595000D01* -X131097000Y-118597000D01* -X131098000Y-118600000D01* -X131098000Y-118602000D01* -X131099000Y-118605000D01* -X131099000Y-118607000D01* -X131100000Y-118610000D01* -X131100000Y-118612000D01* -X131100000Y-118615000D01* -G36* -X131058000Y-118566000D02* -G01* -X131060000Y-118566000D01* -X131063000Y-118567000D01* -X131065000Y-118567000D01* -X131068000Y-118568000D01* -X131070000Y-118569000D01* -X131073000Y-118570000D01* -X131075000Y-118572000D01* -X131077000Y-118573000D01* -X131079000Y-118575000D01* -X131081000Y-118576000D01* -X131083000Y-118578000D01* -X131085000Y-118580000D01* -X131087000Y-118582000D01* -X131089000Y-118584000D01* -X131090000Y-118586000D01* -X131092000Y-118588000D01* -X131093000Y-118590000D01* -X131095000Y-118592000D01* -X131096000Y-118595000D01* -X131097000Y-118597000D01* -X131098000Y-118600000D01* -X131098000Y-118602000D01* -X131099000Y-118605000D01* -X131099000Y-118607000D01* -X131100000Y-118610000D01* -X131100000Y-118612000D01* -X131100000Y-118615000D01* -X131100000Y-118815000D01* -X131100000Y-118818000D01* -X131100000Y-118820000D01* -X131099000Y-118823000D01* -X131099000Y-118825000D01* -X131098000Y-118828000D01* -X131098000Y-118830000D01* -X131097000Y-118833000D01* -X131096000Y-118835000D01* -X131095000Y-118838000D01* -X131093000Y-118840000D01* -X131092000Y-118842000D01* -X131090000Y-118844000D01* -X131089000Y-118846000D01* -X131087000Y-118848000D01* -X131085000Y-118850000D01* -X131083000Y-118852000D01* -X131081000Y-118854000D01* -X131079000Y-118855000D01* -X131077000Y-118857000D01* -X131075000Y-118858000D01* -X131073000Y-118860000D01* -X131070000Y-118861000D01* -X131068000Y-118862000D01* -X131065000Y-118863000D01* -X131063000Y-118863000D01* -X131060000Y-118864000D01* -X131058000Y-118864000D01* -X131055000Y-118865000D01* -X131053000Y-118865000D01* -X131050000Y-118865000D01* -X130550000Y-118865000D01* -X130547000Y-118865000D01* -X130545000Y-118865000D01* -X130542000Y-118864000D01* -X130540000Y-118864000D01* -X130537000Y-118863000D01* -X130535000Y-118863000D01* -X130532000Y-118862000D01* -X130530000Y-118861000D01* -X130527000Y-118860000D01* -X130525000Y-118858000D01* -X130523000Y-118857000D01* -X130521000Y-118855000D01* -X130519000Y-118854000D01* -X130517000Y-118852000D01* -X130515000Y-118850000D01* -X130513000Y-118848000D01* -X130511000Y-118846000D01* -X130510000Y-118844000D01* -X130508000Y-118842000D01* -X130507000Y-118840000D01* -X130505000Y-118838000D01* -X130504000Y-118835000D01* -X130503000Y-118833000D01* -X130502000Y-118830000D01* -X130502000Y-118828000D01* -X130501000Y-118825000D01* -X130501000Y-118823000D01* -X130500000Y-118820000D01* -X130500000Y-118818000D01* -X130500000Y-118815000D01* -X130500000Y-118615000D01* -X130500000Y-118612000D01* -X130500000Y-118610000D01* -X130501000Y-118607000D01* -X130501000Y-118605000D01* -X130502000Y-118602000D01* -X130502000Y-118600000D01* -X130503000Y-118597000D01* -X130504000Y-118595000D01* -X130505000Y-118592000D01* -X130507000Y-118590000D01* -X130508000Y-118588000D01* -X130510000Y-118586000D01* -X130511000Y-118584000D01* -X130513000Y-118582000D01* -X130515000Y-118580000D01* -X130517000Y-118578000D01* -X130519000Y-118576000D01* -X130521000Y-118575000D01* -X130523000Y-118573000D01* -X130525000Y-118572000D01* -X130527000Y-118570000D01* -X130530000Y-118569000D01* -X130532000Y-118568000D01* -X130535000Y-118567000D01* -X130537000Y-118567000D01* -X130540000Y-118566000D01* -X130542000Y-118566000D01* -X130545000Y-118565000D01* -X130547000Y-118565000D01* -X130550000Y-118565000D01* -X131050000Y-118565000D01* -X131053000Y-118565000D01* -X131055000Y-118565000D01* -X131058000Y-118566000D01* -G37* -X131100000Y-119015000D02* -X131100000Y-119215000D01* -X131100000Y-119218000D01* -X131100000Y-119220000D01* -X131099000Y-119223000D01* -X131099000Y-119225000D01* -X131098000Y-119228000D01* -X131098000Y-119230000D01* -X131097000Y-119233000D01* -X131096000Y-119235000D01* -X131095000Y-119238000D01* -X131093000Y-119240000D01* -X131092000Y-119242000D01* -X131090000Y-119244000D01* -X131089000Y-119246000D01* -X131087000Y-119248000D01* -X131085000Y-119250000D01* -X131083000Y-119252000D01* -X131081000Y-119254000D01* -X131079000Y-119255000D01* -X131077000Y-119257000D01* -X131075000Y-119258000D01* -X131073000Y-119260000D01* -X131070000Y-119261000D01* -X131068000Y-119262000D01* -X131065000Y-119263000D01* -X131063000Y-119263000D01* -X131060000Y-119264000D01* -X131058000Y-119264000D01* -X131055000Y-119265000D01* -X131053000Y-119265000D01* -X131050000Y-119265000D01* -X130550000Y-119265000D01* -X130547000Y-119265000D01* -X130545000Y-119265000D01* -X130542000Y-119264000D01* -X130540000Y-119264000D01* -X130537000Y-119263000D01* -X130535000Y-119263000D01* -X130532000Y-119262000D01* -X130530000Y-119261000D01* -X130527000Y-119260000D01* -X130525000Y-119258000D01* -X130523000Y-119257000D01* -X130521000Y-119255000D01* -X130519000Y-119254000D01* -X130517000Y-119252000D01* -X130515000Y-119250000D01* -X130513000Y-119248000D01* -X130511000Y-119246000D01* -X130510000Y-119244000D01* -X130508000Y-119242000D01* -X130507000Y-119240000D01* -X130505000Y-119238000D01* -X130504000Y-119235000D01* -X130503000Y-119233000D01* -X130502000Y-119230000D01* -X130502000Y-119228000D01* -X130501000Y-119225000D01* -X130501000Y-119223000D01* -X130500000Y-119220000D01* -X130500000Y-119218000D01* -X130500000Y-119215000D01* -X130500000Y-119015000D01* -X130500000Y-119012000D01* -X130500000Y-119010000D01* -X130501000Y-119007000D01* -X130501000Y-119005000D01* -X130502000Y-119002000D01* -X130502000Y-119000000D01* -X130503000Y-118997000D01* -X130504000Y-118995000D01* -X130505000Y-118992000D01* -X130507000Y-118990000D01* -X130508000Y-118988000D01* -X130510000Y-118986000D01* -X130511000Y-118984000D01* -X130513000Y-118982000D01* -X130515000Y-118980000D01* -X130517000Y-118978000D01* -X130519000Y-118976000D01* -X130521000Y-118975000D01* -X130523000Y-118973000D01* -X130525000Y-118972000D01* -X130527000Y-118970000D01* -X130530000Y-118969000D01* -X130532000Y-118968000D01* -X130535000Y-118967000D01* -X130537000Y-118967000D01* -X130540000Y-118966000D01* -X130542000Y-118966000D01* -X130545000Y-118965000D01* -X130547000Y-118965000D01* -X130550000Y-118965000D01* -X131050000Y-118965000D01* -X131053000Y-118965000D01* -X131055000Y-118965000D01* -X131058000Y-118966000D01* -X131060000Y-118966000D01* -X131063000Y-118967000D01* -X131065000Y-118967000D01* -X131068000Y-118968000D01* -X131070000Y-118969000D01* -X131073000Y-118970000D01* -X131075000Y-118972000D01* -X131077000Y-118973000D01* -X131079000Y-118975000D01* -X131081000Y-118976000D01* -X131083000Y-118978000D01* -X131085000Y-118980000D01* -X131087000Y-118982000D01* -X131089000Y-118984000D01* -X131090000Y-118986000D01* -X131092000Y-118988000D01* -X131093000Y-118990000D01* -X131095000Y-118992000D01* -X131096000Y-118995000D01* -X131097000Y-118997000D01* -X131098000Y-119000000D01* -X131098000Y-119002000D01* -X131099000Y-119005000D01* -X131099000Y-119007000D01* -X131100000Y-119010000D01* -X131100000Y-119012000D01* -X131100000Y-119015000D01* -G36* -X131058000Y-118966000D02* -G01* -X131060000Y-118966000D01* -X131063000Y-118967000D01* -X131065000Y-118967000D01* -X131068000Y-118968000D01* -X131070000Y-118969000D01* -X131073000Y-118970000D01* -X131075000Y-118972000D01* -X131077000Y-118973000D01* -X131079000Y-118975000D01* -X131081000Y-118976000D01* -X131083000Y-118978000D01* -X131085000Y-118980000D01* -X131087000Y-118982000D01* -X131089000Y-118984000D01* -X131090000Y-118986000D01* -X131092000Y-118988000D01* -X131093000Y-118990000D01* -X131095000Y-118992000D01* -X131096000Y-118995000D01* -X131097000Y-118997000D01* -X131098000Y-119000000D01* -X131098000Y-119002000D01* -X131099000Y-119005000D01* -X131099000Y-119007000D01* -X131100000Y-119010000D01* -X131100000Y-119012000D01* -X131100000Y-119015000D01* -X131100000Y-119215000D01* -X131100000Y-119218000D01* -X131100000Y-119220000D01* -X131099000Y-119223000D01* -X131099000Y-119225000D01* -X131098000Y-119228000D01* -X131098000Y-119230000D01* -X131097000Y-119233000D01* -X131096000Y-119235000D01* -X131095000Y-119238000D01* -X131093000Y-119240000D01* -X131092000Y-119242000D01* -X131090000Y-119244000D01* -X131089000Y-119246000D01* -X131087000Y-119248000D01* -X131085000Y-119250000D01* -X131083000Y-119252000D01* -X131081000Y-119254000D01* -X131079000Y-119255000D01* -X131077000Y-119257000D01* -X131075000Y-119258000D01* -X131073000Y-119260000D01* -X131070000Y-119261000D01* -X131068000Y-119262000D01* -X131065000Y-119263000D01* -X131063000Y-119263000D01* -X131060000Y-119264000D01* -X131058000Y-119264000D01* -X131055000Y-119265000D01* -X131053000Y-119265000D01* -X131050000Y-119265000D01* -X130550000Y-119265000D01* -X130547000Y-119265000D01* -X130545000Y-119265000D01* -X130542000Y-119264000D01* -X130540000Y-119264000D01* -X130537000Y-119263000D01* -X130535000Y-119263000D01* -X130532000Y-119262000D01* -X130530000Y-119261000D01* -X130527000Y-119260000D01* -X130525000Y-119258000D01* -X130523000Y-119257000D01* -X130521000Y-119255000D01* -X130519000Y-119254000D01* -X130517000Y-119252000D01* -X130515000Y-119250000D01* -X130513000Y-119248000D01* -X130511000Y-119246000D01* -X130510000Y-119244000D01* -X130508000Y-119242000D01* -X130507000Y-119240000D01* -X130505000Y-119238000D01* -X130504000Y-119235000D01* -X130503000Y-119233000D01* -X130502000Y-119230000D01* -X130502000Y-119228000D01* -X130501000Y-119225000D01* -X130501000Y-119223000D01* -X130500000Y-119220000D01* -X130500000Y-119218000D01* -X130500000Y-119215000D01* -X130500000Y-119015000D01* -X130500000Y-119012000D01* -X130500000Y-119010000D01* -X130501000Y-119007000D01* -X130501000Y-119005000D01* -X130502000Y-119002000D01* -X130502000Y-119000000D01* -X130503000Y-118997000D01* -X130504000Y-118995000D01* -X130505000Y-118992000D01* -X130507000Y-118990000D01* -X130508000Y-118988000D01* -X130510000Y-118986000D01* -X130511000Y-118984000D01* -X130513000Y-118982000D01* -X130515000Y-118980000D01* -X130517000Y-118978000D01* -X130519000Y-118976000D01* -X130521000Y-118975000D01* -X130523000Y-118973000D01* -X130525000Y-118972000D01* -X130527000Y-118970000D01* -X130530000Y-118969000D01* -X130532000Y-118968000D01* -X130535000Y-118967000D01* -X130537000Y-118967000D01* -X130540000Y-118966000D01* -X130542000Y-118966000D01* -X130545000Y-118965000D01* -X130547000Y-118965000D01* -X130550000Y-118965000D01* -X131050000Y-118965000D01* -X131053000Y-118965000D01* -X131055000Y-118965000D01* -X131058000Y-118966000D01* -G37* +%TO.C,C_3V3_3*% +X140600000Y-104030000D03* +X140600000Y-103070000D03* %TD*% D11* -%TO.C,C_SYS_1*% -X134750000Y-120315000D03* -X136650000Y-120315000D03* -%TD*% -D12* %TO.C,SW_MACRO4*% X123825000Y-101450000D03* X127975000Y-101450000D03* X123825000Y-103600000D03* X127975000Y-103600000D03* %TD*% +D12* +%TO.C,C_OLED_1*% +X124175000Y-105100000D03* +X122625000Y-105100000D03* +%TD*% D13* -%TO.C,C_VIN_2*% -X126750000Y-119275000D03* -X126750000Y-118315000D03* +%TO.C,R_EN_PU1*% +X145490000Y-118600000D03* +X146510000Y-118600000D03* %TD*% -D14* -%TO.C,C_VIN_1*% -X124750000Y-119315000D03* -X122850000Y-119315000D03* +D10* +%TO.C,C_RGB1*% +X125800000Y-125080000D03* +X125800000Y-124120000D03* %TD*% -D15* -%TO.C,C_BUCK_OUT1*% -X131475000Y-110750000D03* -X131475000Y-108850000D03* +D14* +%TO.C,SW_BOOT1*% +X146075000Y-116575000D03* +X146075000Y-112425000D03* +X148225000Y-116575000D03* +X148225000Y-112425000D03* %TD*% -D16* -%TO.C,C_RGB1*% -X127270000Y-123750000D03* -X128230000Y-123750000D03* +D10* +%TO.C,C_TRIG1*% +X131600000Y-103830000D03* +X131600000Y-102870000D03* %TD*% -D17* +D15* %TO.C,FID1*% X126000000Y-61750000D03* %TD*% -D12* +D11* %TO.C,SW_MACRO2*% X132925000Y-94250000D03* X137075000Y-94250000D03* X132925000Y-96400000D03* X137075000Y-96400000D03* %TD*% -D14* -%TO.C,C_BUCK_IN1*% -X140900000Y-114300000D03* -X139000000Y-114300000D03* +D16* +%TO.C,C_EN1*% +X145225000Y-120300000D03* +X146775000Y-120300000D03* %TD*% -D13* -%TO.C,C_SYS_2*% -X132250000Y-120315000D03* -X132250000Y-119355000D03* +D17* +%TO.C,R_USB_DM1*% +X128020000Y-114970000D03* +X128020000Y-113950000D03* %TD*% D18* %TO.C,SW_THR_UP1*% @@ -2921,7 +145,7 @@ D21* X120750000Y-71650000D03* X120750000Y-75350000D03* %TD*% -D12* +D11* %TO.C,SW_MACRO6*% X142025000Y-101450000D03* X146175000Y-101450000D03* @@ -2947,142 +171,214 @@ X127850000Y-125350000D03* X127850000Y-128650000D03* X129650000Y-128650000D03* %TD*% -D11* -%TO.C,C_BAT1*% -X133250000Y-116815000D03* -X135150000Y-116815000D03* -%TD*% D23* %TO.C,MH1*% X122500000Y-62600000D03* %TD*% D24* %TO.C,U_OLED1*% -X122900000Y-106125000D03* -X123900000Y-106125000D03* -X124900000Y-106125000D03* -X125900000Y-106125000D03* +X122900000Y-108125000D03* +X123900000Y-108125000D03* +X124900000Y-108125000D03* +X125900000Y-108125000D03* D25* -X121600000Y-110000000D03* -X127200000Y-110000000D03* -%TD*% -D26* -%TO.C,R_STAT2*% -X133840000Y-114515000D03* -X134860000Y-114515000D03* +X121600000Y-112000000D03* +X127200000Y-112000000D03* %TD*% D23* %TO.C,MH4*% X147000000Y-127000000D03* %TD*% -D17* +D15* %TO.C,FID2*% X143750000Y-61750000D03* %TD*% D26* -%TO.C,R_FB2*% -X133230000Y-106725000D03* -X134250000Y-106725000D03* +%TO.C,C_OLED_2*% +X123880000Y-106300000D03* +X122920000Y-106300000D03* +%TD*% +D27* +%TO.C,U_MCU1*% +X142450000Y-105500000D03* +X141600000Y-105500000D03* +X140750000Y-105500000D03* +X139900000Y-105500000D03* +X139050000Y-105500000D03* +X138200000Y-105500000D03* +X137350000Y-105500000D03* +X136500000Y-105500000D03* +X135650000Y-105500000D03* +X134800000Y-105500000D03* +X133950000Y-105500000D03* +X133100000Y-105500000D03* +X132250000Y-105500000D03* +X131400000Y-105500000D03* +X130550000Y-105500000D03* +D28* +X129500000Y-106550000D03* +X129500000Y-107400000D03* +X129500000Y-108250000D03* +X129500000Y-109100000D03* +X129500000Y-109950000D03* +X129500000Y-110800000D03* +X129500000Y-111650000D03* +X129500000Y-112500000D03* +X129500000Y-113350000D03* +X129500000Y-114200000D03* +X129500000Y-115050000D03* +X129500000Y-115900000D03* +X129500000Y-116750000D03* +X129500000Y-117600000D03* +X129500000Y-118450000D03* +D27* +X130550000Y-119500000D03* +X131400000Y-119500000D03* +X132250000Y-119500000D03* +X133100000Y-119500000D03* +X133950000Y-119500000D03* +X134800000Y-119500000D03* +X135650000Y-119500000D03* +X136500000Y-119500000D03* +X137350000Y-119500000D03* +X138200000Y-119500000D03* +X139050000Y-119500000D03* +X139900000Y-119500000D03* +X140750000Y-119500000D03* +X141600000Y-119500000D03* +X142450000Y-119500000D03* +D28* +X143500000Y-118450000D03* +X143500000Y-117600000D03* +X143500000Y-116750000D03* +X143500000Y-115900000D03* +X143500000Y-115050000D03* +X143500000Y-114200000D03* +X143500000Y-113350000D03* +X143500000Y-112500000D03* +X143500000Y-111650000D03* +X143500000Y-110800000D03* +X143500000Y-109950000D03* +X143500000Y-109100000D03* +X143500000Y-108250000D03* +X143500000Y-107400000D03* +X143500000Y-106550000D03* +D29* +X138150000Y-110850000D03* +D30* +X136500000Y-110850000D03* +X134850000Y-110850000D03* +X138150000Y-112500000D03* +X136500000Y-112500000D03* +X134850000Y-112500000D03* +X138150000Y-114150000D03* +X136500000Y-114150000D03* +X134850000Y-114150000D03* +D31* +X143500000Y-105500000D03* +X129500000Y-105500000D03* +X129500000Y-119500000D03* +X143500000Y-119500000D03* %TD*% D18* %TO.C,SW_VOL_DN1*% X148200000Y-85625000D03* X148200000Y-81375000D03* -D27* +D32* X147300000Y-84725000D03* X147300000Y-82275000D03* -D28* +D33* X147300000Y-83500000D03* -D29* +D34* X149250000Y-85350000D03* X149250000Y-81650000D03* %TD*% -D30* +D35* %TO.C,J_USB1*% X134110000Y-124550000D03* X139890000Y-124550000D03* -D31* +D36* X133750000Y-123105000D03* X134550000Y-123105000D03* -D32* +D37* X135750000Y-123105000D03* X136750000Y-123105000D03* X137250000Y-123105000D03* X138250000Y-123105000D03* -D31* +D36* X139450000Y-123105000D03* X140250000Y-123105000D03* X140250000Y-123105000D03* X139450000Y-123105000D03* -D32* +D37* X138750000Y-123105000D03* X137750000Y-123105000D03* X136250000Y-123105000D03* X135250000Y-123105000D03* -D31* +D36* X134550000Y-123105000D03* X133750000Y-123105000D03* -D33* +D38* X132680000Y-124020000D03* -D34* +D39* X132680000Y-128200000D03* -D33* +D38* X141320000Y-124020000D03* -D34* +D39* X141320000Y-128200000D03* %TD*% -D35* -%TO.C,R_VSET1*% -X122770000Y-115500000D03* -X121750000Y-115500000D03* -%TD*% -D36* +D40* %TO.C,J_STICK1*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D37* +D41* X137500000Y-69770000D03* X143730000Y-81000000D03* X135000000Y-69770000D03* X143730000Y-78500000D03* X132500000Y-69770000D03* X143730000Y-76000000D03* -D38* +D42* X131750000Y-84250000D03* X138250000Y-84250000D03* X131750000Y-88750000D03* X138250000Y-88750000D03* %TD*% -D35* -%TO.C,R_STAT1*% -X125670000Y-117315000D03* -X124650000Y-117315000D03* -%TD*% -%TO.C,R_ISET1*% -X122790000Y-116515000D03* -X121770000Y-116515000D03* -%TD*% -D39* +D26* %TO.C,C_DBNC1*% X124080000Y-125200000D03* X123120000Y-125200000D03* %TD*% -D26* +D17* %TO.C,R_RGB1*% -X127240000Y-122600000D03* -X128260000Y-122600000D03* -%TD*% -D40* -%TO.C,R_FB1*% -X131975000Y-106040000D03* -X131975000Y-107060000D03* +X127900000Y-123500000D03* +X127900000Y-122480000D03* %TD*% D23* %TO.C,MH2*% X147400000Y-62800000D03* %TD*% +D10* +%TO.C,C_3V3_2*% +X140600000Y-102080000D03* +X140600000Y-101120000D03* +%TD*% +D43* +%TO.C,C_3V3_1*% +X145300000Y-106775000D03* +X145300000Y-105225000D03* +%TD*% +D44* +%TO.C,R_VSYS1*% +X129800000Y-100900000D03* +X129800000Y-101920000D03* +%TD*% +%TO.C,R_I2C_SDA1*% +X125500000Y-105280000D03* +X125500000Y-106300000D03* +%TD*% D18* %TO.C,SW_THR_DN1*% X121800000Y-81375000D03* @@ -3096,46 +392,43 @@ D21* X120750000Y-81650000D03* X120750000Y-85350000D03* %TD*% +D44* +%TO.C,R_I2C_SCL1*% +X127200000Y-106390000D03* +X127200000Y-107410000D03* +%TD*% D18* %TO.C,SW_VOL_UP1*% X148200000Y-75625000D03* X148200000Y-71375000D03* -D27* +D32* X147300000Y-74725000D03* X147300000Y-72275000D03* -D28* +D33* X147300000Y-73500000D03* -D29* +D34* X149250000Y-75350000D03* X149250000Y-71650000D03* %TD*% -D41* -%TO.C,U_BUCK1*% -X141875000Y-109800000D03* -X140925000Y-109800000D03* -X139975000Y-109800000D03* -X139975000Y-112075000D03* -X141875000Y-112075000D03* -%TD*% -D42* -%TO.C,L_BUCK1*% -X137500000Y-109800000D03* -X134450000Y-109800000D03* -%TD*% -D17* +D15* %TO.C,FID3*% X148500000Y-121000000D03* %TD*% +D44* +%TO.C,R_VSYS2*% +X130000000Y-102890000D03* +X130000000Y-103910000D03* +%TD*% D18* %TO.C,SW_PWR1*% X120875000Y-127900000D03* X125125000Y-127900000D03* -D43* +D45* X121775000Y-127000000D03* X124225000Y-127000000D03* -D44* +D46* X123000000Y-127000000D03* -D45* +D47* X121150000Y-128950000D03* X124850000Y-128950000D03* %TD*% @@ -3143,22 +436,27 @@ D23* %TO.C,MH3*% X123000000Y-122500000D03* %TD*% -D12* +D17* +%TO.C,R_USB_DP1*% +X128020000Y-116910000D03* +X128020000Y-115890000D03* +%TD*% +D11* %TO.C,SW_MACRO5*% X132925000Y-101450000D03* X137075000Y-101450000D03* X132925000Y-103600000D03* X137075000Y-103600000D03* %TD*% -D35* -%TO.C,R_TS1*% -X122770000Y-114500000D03* -X121750000Y-114500000D03* +D17* +%TO.C,R_BOOT_PU1*% +X145800000Y-109920000D03* +X145800000Y-108900000D03* %TD*% -D46* +D48* %TO.C,BT1*% X145200000Y-123100000D03* -D47* +D49* X147200000Y-123100000D03* %TD*% D18* @@ -3166,10 +464,4 @@ D18* X132875000Y-61800000D03* X137125000Y-61800000D03* %TD*% -D48* -%TO.C,J_SWD1*% -X146300000Y-114775000D03* -X145284000Y-109695000D03* -X147316000Y-109695000D03* -%TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-F_Paste.gbr b/PCB/v2.x/production/gerbers/snips_controller-F_Paste.gbr index 10ad98f..97d7628 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-F_Paste.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-F_Paste.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Paste,Top*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -28,340 +28,94 @@ G04 Aperture macros list* 20,1,$1+$1,$4,$5,$6,$7,0* 20,1,$1+$1,$6,$7,$8,$9,0* 20,1,$1+$1,$8,$9,$2,$3,0*% +%AMFreePoly0* +4,1,6,0.600000,-0.600000,-0.600000,-0.600000,-0.600000,0.000000,0.000000,0.600000,0.600000,0.600000,0.600000,-0.600000,0.600000,-0.600000,$1*% G04 Aperture macros list end* -%ADD10C,0.010000*% -%ADD11RoundRect,0.250000X-0.250000X-0.475000X0.250000X-0.475000X0.250000X0.475000X-0.250000X0.475000X0*% -%ADD12R,1.050000X0.650000*% -%ADD13RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% -%ADD14RoundRect,0.250000X0.250000X0.475000X-0.250000X0.475000X-0.250000X-0.475000X0.250000X-0.475000X0*% -%ADD15RoundRect,0.250000X0.475000X-0.250000X0.475000X0.250000X-0.475000X0.250000X-0.475000X-0.250000X0*% -%ADD16RoundRect,0.140000X-0.140000X-0.170000X0.140000X-0.170000X0.140000X0.170000X-0.140000X0.170000X0*% +%ADD10RoundRect,0.140000X0.170000X-0.140000X0.170000X0.140000X-0.170000X0.140000X-0.170000X-0.140000X0*% +%ADD11R,1.050000X0.650000*% +%ADD12RoundRect,0.225000X0.225000X0.250000X-0.225000X0.250000X-0.225000X-0.250000X0.225000X-0.250000X0*% +%ADD13RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% +%ADD14R,0.650000X1.050000*% +%ADD15RoundRect,0.225000X-0.225000X-0.250000X0.225000X-0.250000X0.225000X0.250000X-0.225000X0.250000X0*% +%ADD16RoundRect,0.135000X0.185000X-0.135000X0.185000X0.135000X-0.185000X0.135000X-0.185000X-0.135000X0*% %ADD17RoundRect,0.187500X-0.712500X0.187500X-0.712500X-0.187500X0.712500X-0.187500X0.712500X0.187500X0*% %ADD18RoundRect,0.150000X-0.750000X0.150000X-0.750000X-0.150000X0.750000X-0.150000X0.750000X0.150000X0*% %ADD19RoundRect,0.225000X-0.225000X0.425000X-0.225000X-0.425000X0.225000X-0.425000X0.225000X0.425000X0*% %ADD20RoundRect,0.150000X0.350000X-0.600000X0.350000X0.600000X-0.350000X0.600000X-0.350000X-0.600000X0*% -%ADD21RoundRect,0.052000X0.198000X0.048000X-0.198000X0.048000X-0.198000X-0.048000X0.198000X-0.048000X0*% -%ADD22RoundRect,0.150000X-0.150000X-0.625000X0.150000X-0.625000X0.150000X0.625000X-0.150000X0.625000X0*% -%ADD23RoundRect,0.250000X-0.350000X-0.650000X0.350000X-0.650000X0.350000X0.650000X-0.350000X0.650000X0*% -%ADD24RoundRect,0.135000X-0.135000X-0.185000X0.135000X-0.185000X0.135000X0.185000X-0.135000X0.185000X0*% -%ADD25RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% -%ADD26RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% -%ADD27RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% -%ADD28RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% -%ADD29RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% -%ADD30RoundRect,0.135000X0.135000X0.185000X-0.135000X0.185000X-0.135000X-0.185000X0.135000X-0.185000X0*% -%ADD31RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% -%ADD32RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% -%ADD33RoundRect,0.150000X-0.150000X0.512500X-0.150000X-0.512500X0.150000X-0.512500X0.150000X0.512500X0*% -%ADD34R,1.500000X3.600000*% -%ADD35RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% -%ADD36RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% -%ADD37RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% +%ADD21RoundRect,0.150000X-0.150000X-0.625000X0.150000X-0.625000X0.150000X0.625000X-0.150000X0.625000X0*% +%ADD22RoundRect,0.250000X-0.350000X-0.650000X0.350000X-0.650000X0.350000X0.650000X-0.350000X0.650000X0*% +%ADD23RoundRect,0.140000X0.140000X0.170000X-0.140000X0.170000X-0.140000X-0.170000X0.140000X-0.170000X0*% +%ADD24R,0.400000X0.800000*% +%ADD25R,0.800000X0.400000*% +%ADD26FreePoly0,270.000000*% +%ADD27R,1.200000X1.200000*% +%ADD28R,0.800000X0.800000*% +%ADD29RoundRect,0.187500X0.712500X-0.187500X0.712500X0.187500X-0.712500X0.187500X-0.712500X-0.187500X0*% +%ADD30RoundRect,0.150000X0.750000X-0.150000X0.750000X0.150000X-0.750000X0.150000X-0.750000X-0.150000X0*% +%ADD31RoundRect,0.225000X0.225000X-0.425000X0.225000X0.425000X-0.225000X0.425000X-0.225000X-0.425000X0*% +%ADD32RoundRect,0.150000X-0.150000X-0.575000X0.150000X-0.575000X0.150000X0.575000X-0.150000X0.575000X0*% +%ADD33RoundRect,0.075000X-0.075000X-0.650000X0.075000X-0.650000X0.075000X0.650000X-0.075000X0.650000X0*% +%ADD34RoundRect,0.225000X0.250000X-0.225000X0.250000X0.225000X-0.250000X0.225000X-0.250000X-0.225000X0*% +%ADD35RoundRect,0.135000X-0.185000X0.135000X-0.185000X-0.135000X0.185000X-0.135000X0.185000X0.135000X0*% +%ADD36RoundRect,0.187500X-0.187500X-0.712500X0.187500X-0.712500X0.187500X0.712500X-0.187500X0.712500X0*% +%ADD37RoundRect,0.150000X-0.150000X-0.750000X0.150000X-0.750000X0.150000X0.750000X-0.150000X0.750000X0*% +%ADD38RoundRect,0.225000X-0.425000X-0.225000X0.425000X-0.225000X0.425000X0.225000X-0.425000X0.225000X0*% G04 APERTURE END LIST* D10* -%TO.C,U_CHG1*% -X130175000Y-117675000D02* -X130175000Y-118955000D01* -X130175000Y-118958000D01* -X130175000Y-118960000D01* -X130174000Y-118963000D01* -X130174000Y-118965000D01* -X130173000Y-118968000D01* -X130173000Y-118970000D01* -X130172000Y-118973000D01* -X130171000Y-118975000D01* -X130170000Y-118978000D01* -X130168000Y-118980000D01* -X130167000Y-118982000D01* -X130165000Y-118984000D01* -X130164000Y-118986000D01* -X130162000Y-118988000D01* -X130160000Y-118990000D01* -X130158000Y-118992000D01* -X130156000Y-118994000D01* -X130154000Y-118995000D01* -X130152000Y-118997000D01* -X130150000Y-118998000D01* -X130148000Y-119000000D01* -X130145000Y-119001000D01* -X130143000Y-119002000D01* -X130140000Y-119003000D01* -X130138000Y-119003000D01* -X130135000Y-119004000D01* -X130133000Y-119004000D01* -X130130000Y-119005000D01* -X130128000Y-119005000D01* -X130125000Y-119005000D01* -X129375000Y-119005000D01* -X129372000Y-119005000D01* -X129370000Y-119005000D01* -X129367000Y-119004000D01* -X129365000Y-119004000D01* -X129362000Y-119003000D01* -X129360000Y-119003000D01* -X129357000Y-119002000D01* -X129355000Y-119001000D01* -X129352000Y-119000000D01* -X129350000Y-118998000D01* -X129348000Y-118997000D01* -X129346000Y-118995000D01* -X129344000Y-118994000D01* -X129342000Y-118992000D01* -X129340000Y-118990000D01* -X129338000Y-118988000D01* -X129336000Y-118986000D01* -X129335000Y-118984000D01* -X129333000Y-118982000D01* -X129332000Y-118980000D01* -X129330000Y-118978000D01* -X129329000Y-118975000D01* -X129328000Y-118973000D01* -X129327000Y-118970000D01* -X129327000Y-118968000D01* -X129326000Y-118965000D01* -X129326000Y-118963000D01* -X129325000Y-118960000D01* -X129325000Y-118958000D01* -X129325000Y-118955000D01* -X129325000Y-117675000D01* -X129325000Y-117672000D01* -X129325000Y-117670000D01* -X129326000Y-117667000D01* -X129326000Y-117665000D01* -X129327000Y-117662000D01* -X129327000Y-117660000D01* -X129328000Y-117657000D01* -X129329000Y-117655000D01* -X129330000Y-117652000D01* -X129332000Y-117650000D01* -X129333000Y-117648000D01* -X129335000Y-117646000D01* -X129336000Y-117644000D01* -X129338000Y-117642000D01* -X129340000Y-117640000D01* -X129342000Y-117638000D01* -X129344000Y-117636000D01* -X129346000Y-117635000D01* -X129348000Y-117633000D01* -X129350000Y-117632000D01* -X129352000Y-117630000D01* -X129355000Y-117629000D01* -X129357000Y-117628000D01* -X129360000Y-117627000D01* -X129362000Y-117627000D01* -X129365000Y-117626000D01* -X129367000Y-117626000D01* -X129370000Y-117625000D01* -X129372000Y-117625000D01* -X129375000Y-117625000D01* -X130125000Y-117625000D01* -X130128000Y-117625000D01* -X130130000Y-117625000D01* -X130133000Y-117626000D01* -X130135000Y-117626000D01* -X130138000Y-117627000D01* -X130140000Y-117627000D01* -X130143000Y-117628000D01* -X130145000Y-117629000D01* -X130148000Y-117630000D01* -X130150000Y-117632000D01* -X130152000Y-117633000D01* -X130154000Y-117635000D01* -X130156000Y-117636000D01* -X130158000Y-117638000D01* -X130160000Y-117640000D01* -X130162000Y-117642000D01* -X130164000Y-117644000D01* -X130165000Y-117646000D01* -X130167000Y-117648000D01* -X130168000Y-117650000D01* -X130170000Y-117652000D01* -X130171000Y-117655000D01* -X130172000Y-117657000D01* -X130173000Y-117660000D01* -X130173000Y-117662000D01* -X130174000Y-117665000D01* -X130174000Y-117667000D01* -X130175000Y-117670000D01* -X130175000Y-117672000D01* -X130175000Y-117675000D01* -G36* -X130133000Y-117626000D02* -G01* -X130135000Y-117626000D01* -X130138000Y-117627000D01* -X130140000Y-117627000D01* -X130143000Y-117628000D01* -X130145000Y-117629000D01* -X130148000Y-117630000D01* -X130150000Y-117632000D01* -X130152000Y-117633000D01* -X130154000Y-117635000D01* -X130156000Y-117636000D01* -X130158000Y-117638000D01* -X130160000Y-117640000D01* -X130162000Y-117642000D01* -X130164000Y-117644000D01* -X130165000Y-117646000D01* -X130167000Y-117648000D01* -X130168000Y-117650000D01* -X130170000Y-117652000D01* -X130171000Y-117655000D01* -X130172000Y-117657000D01* -X130173000Y-117660000D01* -X130173000Y-117662000D01* -X130174000Y-117665000D01* -X130174000Y-117667000D01* -X130175000Y-117670000D01* -X130175000Y-117672000D01* -X130175000Y-117675000D01* -X130175000Y-118955000D01* -X130175000Y-118958000D01* -X130175000Y-118960000D01* -X130174000Y-118963000D01* -X130174000Y-118965000D01* -X130173000Y-118968000D01* -X130173000Y-118970000D01* -X130172000Y-118973000D01* -X130171000Y-118975000D01* -X130170000Y-118978000D01* -X130168000Y-118980000D01* -X130167000Y-118982000D01* -X130165000Y-118984000D01* -X130164000Y-118986000D01* -X130162000Y-118988000D01* -X130160000Y-118990000D01* -X130158000Y-118992000D01* -X130156000Y-118994000D01* -X130154000Y-118995000D01* -X130152000Y-118997000D01* -X130150000Y-118998000D01* -X130148000Y-119000000D01* -X130145000Y-119001000D01* -X130143000Y-119002000D01* -X130140000Y-119003000D01* -X130138000Y-119003000D01* -X130135000Y-119004000D01* -X130133000Y-119004000D01* -X130130000Y-119005000D01* -X130128000Y-119005000D01* -X130125000Y-119005000D01* -X129375000Y-119005000D01* -X129372000Y-119005000D01* -X129370000Y-119005000D01* -X129367000Y-119004000D01* -X129365000Y-119004000D01* -X129362000Y-119003000D01* -X129360000Y-119003000D01* -X129357000Y-119002000D01* -X129355000Y-119001000D01* -X129352000Y-119000000D01* -X129350000Y-118998000D01* -X129348000Y-118997000D01* -X129346000Y-118995000D01* -X129344000Y-118994000D01* -X129342000Y-118992000D01* -X129340000Y-118990000D01* -X129338000Y-118988000D01* -X129336000Y-118986000D01* -X129335000Y-118984000D01* -X129333000Y-118982000D01* -X129332000Y-118980000D01* -X129330000Y-118978000D01* -X129329000Y-118975000D01* -X129328000Y-118973000D01* -X129327000Y-118970000D01* -X129327000Y-118968000D01* -X129326000Y-118965000D01* -X129326000Y-118963000D01* -X129325000Y-118960000D01* -X129325000Y-118958000D01* -X129325000Y-118955000D01* -X129325000Y-117675000D01* -X129325000Y-117672000D01* -X129325000Y-117670000D01* -X129326000Y-117667000D01* -X129326000Y-117665000D01* -X129327000Y-117662000D01* -X129327000Y-117660000D01* -X129328000Y-117657000D01* -X129329000Y-117655000D01* -X129330000Y-117652000D01* -X129332000Y-117650000D01* -X129333000Y-117648000D01* -X129335000Y-117646000D01* -X129336000Y-117644000D01* -X129338000Y-117642000D01* -X129340000Y-117640000D01* -X129342000Y-117638000D01* -X129344000Y-117636000D01* -X129346000Y-117635000D01* -X129348000Y-117633000D01* -X129350000Y-117632000D01* -X129352000Y-117630000D01* -X129355000Y-117629000D01* -X129357000Y-117628000D01* -X129360000Y-117627000D01* -X129362000Y-117627000D01* -X129365000Y-117626000D01* -X129367000Y-117626000D01* -X129370000Y-117625000D01* -X129372000Y-117625000D01* -X129375000Y-117625000D01* -X130125000Y-117625000D01* -X130128000Y-117625000D01* -X130130000Y-117625000D01* -X130133000Y-117626000D01* -G37* +%TO.C,C_3V3_3*% +X140600000Y-104030000D03* +X140600000Y-103070000D03* %TD*% D11* -%TO.C,C_SYS_1*% -X134750000Y-120315000D03* -X136650000Y-120315000D03* -%TD*% -D12* %TO.C,SW_MACRO4*% X123825000Y-101450000D03* X127975000Y-101450000D03* X123825000Y-103600000D03* X127975000Y-103600000D03* %TD*% +D12* +%TO.C,C_OLED_1*% +X124175000Y-105100000D03* +X122625000Y-105100000D03* +%TD*% D13* -%TO.C,C_VIN_2*% -X126750000Y-119275000D03* -X126750000Y-118315000D03* +%TO.C,R_EN_PU1*% +X145490000Y-118600000D03* +X146510000Y-118600000D03* %TD*% -D14* -%TO.C,C_VIN_1*% -X124750000Y-119315000D03* -X122850000Y-119315000D03* +D10* +%TO.C,C_RGB1*% +X125800000Y-125080000D03* +X125800000Y-124120000D03* %TD*% -D15* -%TO.C,C_BUCK_OUT1*% -X131475000Y-110750000D03* -X131475000Y-108850000D03* +D14* +%TO.C,SW_BOOT1*% +X146075000Y-116575000D03* +X146075000Y-112425000D03* +X148225000Y-116575000D03* +X148225000Y-112425000D03* %TD*% -D16* -%TO.C,C_RGB1*% -X127270000Y-123750000D03* -X128230000Y-123750000D03* +D10* +%TO.C,C_TRIG1*% +X131600000Y-103830000D03* +X131600000Y-102870000D03* %TD*% -D12* +D11* %TO.C,SW_MACRO2*% X132925000Y-94250000D03* X137075000Y-94250000D03* X132925000Y-96400000D03* X137075000Y-96400000D03* %TD*% -D14* -%TO.C,C_BUCK_IN1*% -X140900000Y-114300000D03* -X139000000Y-114300000D03* +D15* +%TO.C,C_EN1*% +X145225000Y-120300000D03* +X146775000Y-120300000D03* %TD*% -D13* -%TO.C,C_SYS_2*% -X132250000Y-120315000D03* -X132250000Y-119355000D03* +D16* +%TO.C,R_USB_DM1*% +X128020000Y-114970000D03* +X128020000Y-113950000D03* %TD*% D17* %TO.C,SW_THR_UP1*% @@ -373,7 +127,7 @@ D19* X120750000Y-71650000D03* X120750000Y-75350000D03* %TD*% -D12* +D11* %TO.C,SW_MACRO6*% X142025000Y-101450000D03* X146175000Y-101450000D03* @@ -399,103 +153,164 @@ X127850000Y-125350000D03* X127850000Y-128650000D03* X129650000Y-128650000D03* %TD*% -D11* -%TO.C,C_BAT1*% -X133250000Y-116815000D03* -X135150000Y-116815000D03* -%TD*% D21* -%TO.C,U_CHG1*% -X130800000Y-119115000D03* -X130800000Y-118715000D03* -X130800000Y-118315000D03* -X130800000Y-117915000D03* -X130800000Y-117515000D03* -X128700000Y-117515000D03* -X128700000Y-117915000D03* -X128700000Y-118315000D03* -X128700000Y-118715000D03* -X128700000Y-119115000D03* -%TD*% -D22* %TO.C,U_OLED1*% -X122900000Y-106125000D03* -X123900000Y-106125000D03* -X124900000Y-106125000D03* -X125900000Y-106125000D03* +X122900000Y-108125000D03* +X123900000Y-108125000D03* +X124900000Y-108125000D03* +X125900000Y-108125000D03* +D22* +X121600000Y-112000000D03* +X127200000Y-112000000D03* +%TD*% D23* -X121600000Y-110000000D03* -X127200000Y-110000000D03* +%TO.C,C_OLED_2*% +X123880000Y-106300000D03* +X122920000Y-106300000D03* %TD*% D24* -%TO.C,R_STAT2*% -X133840000Y-114515000D03* -X134860000Y-114515000D03* -%TD*% -%TO.C,R_FB2*% -X133230000Y-106725000D03* -X134250000Y-106725000D03* -%TD*% +%TO.C,U_MCU1*% +X142450000Y-105500000D03* +X141600000Y-105500000D03* +X140750000Y-105500000D03* +X139900000Y-105500000D03* +X139050000Y-105500000D03* +X138200000Y-105500000D03* +X137350000Y-105500000D03* +X136500000Y-105500000D03* +X135650000Y-105500000D03* +X134800000Y-105500000D03* +X133950000Y-105500000D03* +X133100000Y-105500000D03* +X132250000Y-105500000D03* +X131400000Y-105500000D03* +X130550000Y-105500000D03* +D25* +X129500000Y-106550000D03* +X129500000Y-107400000D03* +X129500000Y-108250000D03* +X129500000Y-109100000D03* +X129500000Y-109950000D03* +X129500000Y-110800000D03* +X129500000Y-111650000D03* +X129500000Y-112500000D03* +X129500000Y-113350000D03* +X129500000Y-114200000D03* +X129500000Y-115050000D03* +X129500000Y-115900000D03* +X129500000Y-116750000D03* +X129500000Y-117600000D03* +X129500000Y-118450000D03* +D24* +X130550000Y-119500000D03* +X131400000Y-119500000D03* +X132250000Y-119500000D03* +X133100000Y-119500000D03* +X133950000Y-119500000D03* +X134800000Y-119500000D03* +X135650000Y-119500000D03* +X136500000Y-119500000D03* +X137350000Y-119500000D03* +X138200000Y-119500000D03* +X139050000Y-119500000D03* +X139900000Y-119500000D03* +X140750000Y-119500000D03* +X141600000Y-119500000D03* +X142450000Y-119500000D03* D25* +X143500000Y-118450000D03* +X143500000Y-117600000D03* +X143500000Y-116750000D03* +X143500000Y-115900000D03* +X143500000Y-115050000D03* +X143500000Y-114200000D03* +X143500000Y-113350000D03* +X143500000Y-112500000D03* +X143500000Y-111650000D03* +X143500000Y-110800000D03* +X143500000Y-109950000D03* +X143500000Y-109100000D03* +X143500000Y-108250000D03* +X143500000Y-107400000D03* +X143500000Y-106550000D03* +D26* +X138150000Y-110850000D03* +D27* +X136500000Y-110850000D03* +X134850000Y-110850000D03* +X138150000Y-112500000D03* +X136500000Y-112500000D03* +X134850000Y-112500000D03* +X138150000Y-114150000D03* +X136500000Y-114150000D03* +X134850000Y-114150000D03* +D28* +X143500000Y-105500000D03* +X129500000Y-105500000D03* +X129500000Y-119500000D03* +X143500000Y-119500000D03* +%TD*% +D29* %TO.C,SW_VOL_DN1*% X147300000Y-84725000D03* X147300000Y-82275000D03* -D26* +D30* X147300000Y-83500000D03* -D27* +D31* X149250000Y-85350000D03* X149250000Y-81650000D03* %TD*% -D28* +D32* %TO.C,J_USB1*% X133750000Y-123105000D03* X134550000Y-123105000D03* -D29* +D33* X135750000Y-123105000D03* X136750000Y-123105000D03* X137250000Y-123105000D03* X138250000Y-123105000D03* -D28* +D32* X139450000Y-123105000D03* X140250000Y-123105000D03* X140250000Y-123105000D03* X139450000Y-123105000D03* -D29* +D33* X138750000Y-123105000D03* X137750000Y-123105000D03* X136250000Y-123105000D03* X135250000Y-123105000D03* -D28* +D32* X134550000Y-123105000D03* X133750000Y-123105000D03* %TD*% -D30* -%TO.C,R_VSET1*% -X122770000Y-115500000D03* -X121750000Y-115500000D03* -%TD*% -%TO.C,R_STAT1*% -X125670000Y-117315000D03* -X124650000Y-117315000D03* -%TD*% -%TO.C,R_ISET1*% -X122790000Y-116515000D03* -X121770000Y-116515000D03* -%TD*% -D31* +D23* %TO.C,C_DBNC1*% X124080000Y-125200000D03* X123120000Y-125200000D03* %TD*% -D24* +D16* %TO.C,R_RGB1*% -X127240000Y-122600000D03* -X128260000Y-122600000D03* +X127900000Y-123500000D03* +X127900000Y-122480000D03* %TD*% -D32* -%TO.C,R_FB1*% -X131975000Y-106040000D03* -X131975000Y-107060000D03* +D10* +%TO.C,C_3V3_2*% +X140600000Y-102080000D03* +X140600000Y-101120000D03* +%TD*% +D34* +%TO.C,C_3V3_1*% +X145300000Y-106775000D03* +X145300000Y-105225000D03* +%TD*% +D35* +%TO.C,R_VSYS1*% +X129800000Y-100900000D03* +X129800000Y-101920000D03* +%TD*% +%TO.C,R_I2C_SDA1*% +X125500000Y-105280000D03* +X125500000Y-106300000D03* %TD*% D17* %TO.C,SW_THR_DN1*% @@ -507,49 +322,51 @@ D19* X120750000Y-81650000D03* X120750000Y-85350000D03* %TD*% -D25* +D35* +%TO.C,R_I2C_SCL1*% +X127200000Y-106390000D03* +X127200000Y-107410000D03* +%TD*% +D29* %TO.C,SW_VOL_UP1*% X147300000Y-74725000D03* X147300000Y-72275000D03* -D26* +D30* X147300000Y-73500000D03* -D27* +D31* X149250000Y-75350000D03* X149250000Y-71650000D03* %TD*% -D33* -%TO.C,U_BUCK1*% -X141875000Y-109800000D03* -X140925000Y-109800000D03* -X139975000Y-109800000D03* -X139975000Y-112075000D03* -X141875000Y-112075000D03* -%TD*% -D34* -%TO.C,L_BUCK1*% -X137500000Y-109800000D03* -X134450000Y-109800000D03* -%TD*% D35* +%TO.C,R_VSYS2*% +X130000000Y-102890000D03* +X130000000Y-103910000D03* +%TD*% +D36* %TO.C,SW_PWR1*% X121775000Y-127000000D03* X124225000Y-127000000D03* -D36* -X123000000Y-127000000D03* D37* +X123000000Y-127000000D03* +D38* X121150000Y-128950000D03* X124850000Y-128950000D03* %TD*% -D12* +D16* +%TO.C,R_USB_DP1*% +X128020000Y-116910000D03* +X128020000Y-115890000D03* +%TD*% +D11* %TO.C,SW_MACRO5*% X132925000Y-101450000D03* X137075000Y-101450000D03* X132925000Y-103600000D03* X137075000Y-103600000D03* %TD*% -D30* -%TO.C,R_TS1*% -X122770000Y-114500000D03* -X121750000Y-114500000D03* +D16* +%TO.C,R_BOOT_PU1*% +X145800000Y-109920000D03* +X145800000Y-108900000D03* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-F_Silkscreen.gbr b/PCB/v2.x/production/gerbers/snips_controller-F_Silkscreen.gbr index fb9ea54..b7b7818 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-F_Silkscreen.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-F_Silkscreen.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Legend,Top*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -14,7 +14,6 @@ G04 APERTURE LIST* %ADD10C,0.100000*% %ADD11C,0.120000*% %ADD12C,0.200000*% -%ADD13C,0.000000*% G04 APERTURE END LIST* D10* X121357139Y-98482823D02* @@ -1560,269 +1559,373 @@ X148766670Y-99275539D01* X148766670Y-99275539D02* X148842860Y-99313635D01* D11* -X122498049Y-112090476D02* -X122536144Y-112014286D01* -X122536144Y-112014286D02* -X122536144Y-111900000D01* -X122536144Y-111900000D02* -X122498049Y-111785714D01* -X122498049Y-111785714D02* -X122421859Y-111709524D01* -X122421859Y-111709524D02* -X122345668Y-111671429D01* -X122345668Y-111671429D02* -X122193287Y-111633333D01* -X122193287Y-111633333D02* -X122079001Y-111633333D01* -X122079001Y-111633333D02* -X121926620Y-111671429D01* -X121926620Y-111671429D02* -X121850430Y-111709524D01* -X121850430Y-111709524D02* -X121774240Y-111785714D01* -X121774240Y-111785714D02* -X121736144Y-111900000D01* -X121736144Y-111900000D02* -X121736144Y-111976191D01* -X121736144Y-111976191D02* -X121774240Y-112090476D01* -X121774240Y-112090476D02* -X121812335Y-112128572D01* -X121812335Y-112128572D02* -X122079001Y-112128572D01* -X122079001Y-112128572D02* -X122079001Y-111976191D01* -X121736144Y-112471429D02* -X122536144Y-112471429D01* -X122536144Y-112471429D02* -X121736144Y-112928572D01* -X121736144Y-112928572D02* -X122536144Y-112928572D01* -X121736144Y-113309524D02* -X122536144Y-113309524D01* -X122536144Y-113309524D02* -X122536144Y-113500000D01* -X122536144Y-113500000D02* -X122498049Y-113614286D01* -X122498049Y-113614286D02* -X122421859Y-113690476D01* -X122421859Y-113690476D02* -X122345668Y-113728571D01* -X122345668Y-113728571D02* -X122193287Y-113766667D01* -X122193287Y-113766667D02* -X122079001Y-113766667D01* -X122079001Y-113766667D02* -X121926620Y-113728571D01* -X121926620Y-113728571D02* -X121850430Y-113690476D01* -X121850430Y-113690476D02* -X121774240Y-113614286D01* -X121774240Y-113614286D02* -X121736144Y-113500000D01* -X121736144Y-113500000D02* -X121736144Y-113309524D01* -X123836144Y-111609523D02* -X123836144Y-112104761D01* -X123836144Y-112104761D02* -X123531382Y-111838095D01* -X123531382Y-111838095D02* -X123531382Y-111952380D01* -X123531382Y-111952380D02* -X123493287Y-112028571D01* -X123493287Y-112028571D02* -X123455192Y-112066666D01* -X123455192Y-112066666D02* -X123379001Y-112104761D01* -X123379001Y-112104761D02* -X123188525Y-112104761D01* -X123188525Y-112104761D02* -X123112335Y-112066666D01* -X123112335Y-112066666D02* -X123074240Y-112028571D01* -X123074240Y-112028571D02* -X123036144Y-111952380D01* -X123036144Y-111952380D02* -X123036144Y-111723809D01* -X123036144Y-111723809D02* -X123074240Y-111647618D01* -X123074240Y-111647618D02* -X123112335Y-111609523D01* -X123836144Y-112333333D02* -X123036144Y-112600000D01* -X123036144Y-112600000D02* -X123836144Y-112866666D01* -X123836144Y-113057142D02* -X123836144Y-113552380D01* -X123836144Y-113552380D02* -X123531382Y-113285714D01* -X123531382Y-113285714D02* -X123531382Y-113399999D01* -X123531382Y-113399999D02* -X123493287Y-113476190D01* -X123493287Y-113476190D02* -X123455192Y-113514285D01* -X123455192Y-113514285D02* -X123379001Y-113552380D01* -X123379001Y-113552380D02* -X123188525Y-113552380D01* -X123188525Y-113552380D02* -X123112335Y-113514285D01* -X123112335Y-113514285D02* -X123074240Y-113476190D01* -X123074240Y-113476190D02* -X123036144Y-113399999D01* -X123036144Y-113399999D02* -X123036144Y-113171428D01* -X123036144Y-113171428D02* -X123074240Y-113095237D01* -X123074240Y-113095237D02* -X123112335Y-113057142D01* -X124474240Y-111628571D02* -X124436144Y-111742857D01* -X124436144Y-111742857D02* -X124436144Y-111933333D01* -X124436144Y-111933333D02* -X124474240Y-112009524D01* -X124474240Y-112009524D02* -X124512335Y-112047619D01* -X124512335Y-112047619D02* -X124588525Y-112085714D01* -X124588525Y-112085714D02* -X124664716Y-112085714D01* -X124664716Y-112085714D02* -X124740906Y-112047619D01* -X124740906Y-112047619D02* -X124779001Y-112009524D01* -X124779001Y-112009524D02* -X124817097Y-111933333D01* -X124817097Y-111933333D02* -X124855192Y-111780952D01* -X124855192Y-111780952D02* -X124893287Y-111704762D01* -X124893287Y-111704762D02* -X124931382Y-111666667D01* -X124931382Y-111666667D02* -X125007573Y-111628571D01* -X125007573Y-111628571D02* -X125083763Y-111628571D01* -X125083763Y-111628571D02* -X125159954Y-111666667D01* -X125159954Y-111666667D02* -X125198049Y-111704762D01* -X125198049Y-111704762D02* -X125236144Y-111780952D01* -X125236144Y-111780952D02* -X125236144Y-111971429D01* -X125236144Y-111971429D02* -X125198049Y-112085714D01* -X124436144Y-112428572D02* -X125236144Y-112428572D01* -X125236144Y-112428572D02* -X125236144Y-112619048D01* -X125236144Y-112619048D02* -X125198049Y-112733334D01* -X125198049Y-112733334D02* -X125121859Y-112809524D01* -X125121859Y-112809524D02* -X125045668Y-112847619D01* -X125045668Y-112847619D02* -X124893287Y-112885715D01* -X124893287Y-112885715D02* -X124779001Y-112885715D01* -X124779001Y-112885715D02* -X124626620Y-112847619D01* -X124626620Y-112847619D02* -X124550430Y-112809524D01* -X124550430Y-112809524D02* -X124474240Y-112733334D01* -X124474240Y-112733334D02* -X124436144Y-112619048D01* -X124436144Y-112619048D02* -X124436144Y-112428572D01* -X124664716Y-113190476D02* -X124664716Y-113571429D01* -X124436144Y-113114286D02* -X125236144Y-113380953D01* -X125236144Y-113380953D02* -X124436144Y-113647619D01* -X125774240Y-111647618D02* -X125736144Y-111761904D01* -X125736144Y-111761904D02* -X125736144Y-111952380D01* -X125736144Y-111952380D02* -X125774240Y-112028571D01* -X125774240Y-112028571D02* -X125812335Y-112066666D01* -X125812335Y-112066666D02* -X125888525Y-112104761D01* -X125888525Y-112104761D02* -X125964716Y-112104761D01* -X125964716Y-112104761D02* -X126040906Y-112066666D01* -X126040906Y-112066666D02* -X126079001Y-112028571D01* -X126079001Y-112028571D02* -X126117097Y-111952380D01* -X126117097Y-111952380D02* -X126155192Y-111799999D01* -X126155192Y-111799999D02* -X126193287Y-111723809D01* -X126193287Y-111723809D02* -X126231382Y-111685714D01* -X126231382Y-111685714D02* -X126307573Y-111647618D01* -X126307573Y-111647618D02* -X126383763Y-111647618D01* -X126383763Y-111647618D02* -X126459954Y-111685714D01* -X126459954Y-111685714D02* -X126498049Y-111723809D01* -X126498049Y-111723809D02* -X126536144Y-111799999D01* -X126536144Y-111799999D02* -X126536144Y-111990476D01* -X126536144Y-111990476D02* -X126498049Y-112104761D01* -X125812335Y-112904762D02* -X125774240Y-112866666D01* -X125774240Y-112866666D02* -X125736144Y-112752381D01* -X125736144Y-112752381D02* -X125736144Y-112676190D01* -X125736144Y-112676190D02* -X125774240Y-112561904D01* -X125774240Y-112561904D02* -X125850430Y-112485714D01* -X125850430Y-112485714D02* -X125926620Y-112447619D01* -X125926620Y-112447619D02* -X126079001Y-112409523D01* -X126079001Y-112409523D02* -X126193287Y-112409523D01* -X126193287Y-112409523D02* -X126345668Y-112447619D01* -X126345668Y-112447619D02* -X126421859Y-112485714D01* -X126421859Y-112485714D02* -X126498049Y-112561904D01* -X126498049Y-112561904D02* -X126536144Y-112676190D01* -X126536144Y-112676190D02* -X126536144Y-112752381D01* -X126536144Y-112752381D02* -X126498049Y-112866666D01* -X126498049Y-112866666D02* -X126459954Y-112904762D01* -X125736144Y-113628571D02* -X125736144Y-113247619D01* -X125736144Y-113247619D02* -X126536144Y-113247619D01* -%TO.C,C_SYS_1*% -X135438748Y-119580000D02* -X135961252Y-119580000D01* -X135438748Y-121050000D02* -X135961252Y-121050000D01* +X146064285Y-110644807D02* +X146178571Y-110682902D01* +X146178571Y-110682902D02* +X146216666Y-110720998D01* +X146216666Y-110720998D02* +X146254762Y-110797188D01* +X146254762Y-110797188D02* +X146254762Y-110911474D01* +X146254762Y-110911474D02* +X146216666Y-110987664D01* +X146216666Y-110987664D02* +X146178571Y-111025760D01* +X146178571Y-111025760D02* +X146102381Y-111063855D01* +X146102381Y-111063855D02* +X145797619Y-111063855D01* +X145797619Y-111063855D02* +X145797619Y-110263855D01* +X145797619Y-110263855D02* +X146064285Y-110263855D01* +X146064285Y-110263855D02* +X146140476Y-110301950D01* +X146140476Y-110301950D02* +X146178571Y-110340045D01* +X146178571Y-110340045D02* +X146216666Y-110416236D01* +X146216666Y-110416236D02* +X146216666Y-110492426D01* +X146216666Y-110492426D02* +X146178571Y-110568617D01* +X146178571Y-110568617D02* +X146140476Y-110606712D01* +X146140476Y-110606712D02* +X146064285Y-110644807D01* +X146064285Y-110644807D02* +X145797619Y-110644807D01* +X146750000Y-110263855D02* +X146902381Y-110263855D01* +X146902381Y-110263855D02* +X146978571Y-110301950D01* +X146978571Y-110301950D02* +X147054762Y-110378140D01* +X147054762Y-110378140D02* +X147092857Y-110530521D01* +X147092857Y-110530521D02* +X147092857Y-110797188D01* +X147092857Y-110797188D02* +X147054762Y-110949569D01* +X147054762Y-110949569D02* +X146978571Y-111025760D01* +X146978571Y-111025760D02* +X146902381Y-111063855D01* +X146902381Y-111063855D02* +X146750000Y-111063855D01* +X146750000Y-111063855D02* +X146673809Y-111025760D01* +X146673809Y-111025760D02* +X146597619Y-110949569D01* +X146597619Y-110949569D02* +X146559523Y-110797188D01* +X146559523Y-110797188D02* +X146559523Y-110530521D01* +X146559523Y-110530521D02* +X146597619Y-110378140D01* +X146597619Y-110378140D02* +X146673809Y-110301950D01* +X146673809Y-110301950D02* +X146750000Y-110263855D01* +X147588095Y-110263855D02* +X147740476Y-110263855D01* +X147740476Y-110263855D02* +X147816666Y-110301950D01* +X147816666Y-110301950D02* +X147892857Y-110378140D01* +X147892857Y-110378140D02* +X147930952Y-110530521D01* +X147930952Y-110530521D02* +X147930952Y-110797188D01* +X147930952Y-110797188D02* +X147892857Y-110949569D01* +X147892857Y-110949569D02* +X147816666Y-111025760D01* +X147816666Y-111025760D02* +X147740476Y-111063855D01* +X147740476Y-111063855D02* +X147588095Y-111063855D01* +X147588095Y-111063855D02* +X147511904Y-111025760D01* +X147511904Y-111025760D02* +X147435714Y-110949569D01* +X147435714Y-110949569D02* +X147397618Y-110797188D01* +X147397618Y-110797188D02* +X147397618Y-110530521D01* +X147397618Y-110530521D02* +X147435714Y-110378140D01* +X147435714Y-110378140D02* +X147511904Y-110301950D01* +X147511904Y-110301950D02* +X147588095Y-110263855D01* +X148159523Y-110263855D02* +X148616666Y-110263855D01* +X148388094Y-111063855D02* +X148388094Y-110263855D01* +X122498049Y-114090476D02* +X122536144Y-114014286D01* +X122536144Y-114014286D02* +X122536144Y-113900000D01* +X122536144Y-113900000D02* +X122498049Y-113785714D01* +X122498049Y-113785714D02* +X122421859Y-113709524D01* +X122421859Y-113709524D02* +X122345668Y-113671429D01* +X122345668Y-113671429D02* +X122193287Y-113633333D01* +X122193287Y-113633333D02* +X122079001Y-113633333D01* +X122079001Y-113633333D02* +X121926620Y-113671429D01* +X121926620Y-113671429D02* +X121850430Y-113709524D01* +X121850430Y-113709524D02* +X121774240Y-113785714D01* +X121774240Y-113785714D02* +X121736144Y-113900000D01* +X121736144Y-113900000D02* +X121736144Y-113976191D01* +X121736144Y-113976191D02* +X121774240Y-114090476D01* +X121774240Y-114090476D02* +X121812335Y-114128572D01* +X121812335Y-114128572D02* +X122079001Y-114128572D01* +X122079001Y-114128572D02* +X122079001Y-113976191D01* +X121736144Y-114471429D02* +X122536144Y-114471429D01* +X122536144Y-114471429D02* +X121736144Y-114928572D01* +X121736144Y-114928572D02* +X122536144Y-114928572D01* +X121736144Y-115309524D02* +X122536144Y-115309524D01* +X122536144Y-115309524D02* +X122536144Y-115500000D01* +X122536144Y-115500000D02* +X122498049Y-115614286D01* +X122498049Y-115614286D02* +X122421859Y-115690476D01* +X122421859Y-115690476D02* +X122345668Y-115728571D01* +X122345668Y-115728571D02* +X122193287Y-115766667D01* +X122193287Y-115766667D02* +X122079001Y-115766667D01* +X122079001Y-115766667D02* +X121926620Y-115728571D01* +X121926620Y-115728571D02* +X121850430Y-115690476D01* +X121850430Y-115690476D02* +X121774240Y-115614286D01* +X121774240Y-115614286D02* +X121736144Y-115500000D01* +X121736144Y-115500000D02* +X121736144Y-115309524D01* +X123836144Y-113609523D02* +X123836144Y-114104761D01* +X123836144Y-114104761D02* +X123531382Y-113838095D01* +X123531382Y-113838095D02* +X123531382Y-113952380D01* +X123531382Y-113952380D02* +X123493287Y-114028571D01* +X123493287Y-114028571D02* +X123455192Y-114066666D01* +X123455192Y-114066666D02* +X123379001Y-114104761D01* +X123379001Y-114104761D02* +X123188525Y-114104761D01* +X123188525Y-114104761D02* +X123112335Y-114066666D01* +X123112335Y-114066666D02* +X123074240Y-114028571D01* +X123074240Y-114028571D02* +X123036144Y-113952380D01* +X123036144Y-113952380D02* +X123036144Y-113723809D01* +X123036144Y-113723809D02* +X123074240Y-113647618D01* +X123074240Y-113647618D02* +X123112335Y-113609523D01* +X123836144Y-114333333D02* +X123036144Y-114600000D01* +X123036144Y-114600000D02* +X123836144Y-114866666D01* +X123836144Y-115057142D02* +X123836144Y-115552380D01* +X123836144Y-115552380D02* +X123531382Y-115285714D01* +X123531382Y-115285714D02* +X123531382Y-115399999D01* +X123531382Y-115399999D02* +X123493287Y-115476190D01* +X123493287Y-115476190D02* +X123455192Y-115514285D01* +X123455192Y-115514285D02* +X123379001Y-115552380D01* +X123379001Y-115552380D02* +X123188525Y-115552380D01* +X123188525Y-115552380D02* +X123112335Y-115514285D01* +X123112335Y-115514285D02* +X123074240Y-115476190D01* +X123074240Y-115476190D02* +X123036144Y-115399999D01* +X123036144Y-115399999D02* +X123036144Y-115171428D01* +X123036144Y-115171428D02* +X123074240Y-115095237D01* +X123074240Y-115095237D02* +X123112335Y-115057142D01* +X124474240Y-113628571D02* +X124436144Y-113742857D01* +X124436144Y-113742857D02* +X124436144Y-113933333D01* +X124436144Y-113933333D02* +X124474240Y-114009524D01* +X124474240Y-114009524D02* +X124512335Y-114047619D01* +X124512335Y-114047619D02* +X124588525Y-114085714D01* +X124588525Y-114085714D02* +X124664716Y-114085714D01* +X124664716Y-114085714D02* +X124740906Y-114047619D01* +X124740906Y-114047619D02* +X124779001Y-114009524D01* +X124779001Y-114009524D02* +X124817097Y-113933333D01* +X124817097Y-113933333D02* +X124855192Y-113780952D01* +X124855192Y-113780952D02* +X124893287Y-113704762D01* +X124893287Y-113704762D02* +X124931382Y-113666667D01* +X124931382Y-113666667D02* +X125007573Y-113628571D01* +X125007573Y-113628571D02* +X125083763Y-113628571D01* +X125083763Y-113628571D02* +X125159954Y-113666667D01* +X125159954Y-113666667D02* +X125198049Y-113704762D01* +X125198049Y-113704762D02* +X125236144Y-113780952D01* +X125236144Y-113780952D02* +X125236144Y-113971429D01* +X125236144Y-113971429D02* +X125198049Y-114085714D01* +X124436144Y-114428572D02* +X125236144Y-114428572D01* +X125236144Y-114428572D02* +X125236144Y-114619048D01* +X125236144Y-114619048D02* +X125198049Y-114733334D01* +X125198049Y-114733334D02* +X125121859Y-114809524D01* +X125121859Y-114809524D02* +X125045668Y-114847619D01* +X125045668Y-114847619D02* +X124893287Y-114885715D01* +X124893287Y-114885715D02* +X124779001Y-114885715D01* +X124779001Y-114885715D02* +X124626620Y-114847619D01* +X124626620Y-114847619D02* +X124550430Y-114809524D01* +X124550430Y-114809524D02* +X124474240Y-114733334D01* +X124474240Y-114733334D02* +X124436144Y-114619048D01* +X124436144Y-114619048D02* +X124436144Y-114428572D01* +X124664716Y-115190476D02* +X124664716Y-115571429D01* +X124436144Y-115114286D02* +X125236144Y-115380953D01* +X125236144Y-115380953D02* +X124436144Y-115647619D01* +X125774240Y-113647618D02* +X125736144Y-113761904D01* +X125736144Y-113761904D02* +X125736144Y-113952380D01* +X125736144Y-113952380D02* +X125774240Y-114028571D01* +X125774240Y-114028571D02* +X125812335Y-114066666D01* +X125812335Y-114066666D02* +X125888525Y-114104761D01* +X125888525Y-114104761D02* +X125964716Y-114104761D01* +X125964716Y-114104761D02* +X126040906Y-114066666D01* +X126040906Y-114066666D02* +X126079001Y-114028571D01* +X126079001Y-114028571D02* +X126117097Y-113952380D01* +X126117097Y-113952380D02* +X126155192Y-113799999D01* +X126155192Y-113799999D02* +X126193287Y-113723809D01* +X126193287Y-113723809D02* +X126231382Y-113685714D01* +X126231382Y-113685714D02* +X126307573Y-113647618D01* +X126307573Y-113647618D02* +X126383763Y-113647618D01* +X126383763Y-113647618D02* +X126459954Y-113685714D01* +X126459954Y-113685714D02* +X126498049Y-113723809D01* +X126498049Y-113723809D02* +X126536144Y-113799999D01* +X126536144Y-113799999D02* +X126536144Y-113990476D01* +X126536144Y-113990476D02* +X126498049Y-114104761D01* +X125812335Y-114904762D02* +X125774240Y-114866666D01* +X125774240Y-114866666D02* +X125736144Y-114752381D01* +X125736144Y-114752381D02* +X125736144Y-114676190D01* +X125736144Y-114676190D02* +X125774240Y-114561904D01* +X125774240Y-114561904D02* +X125850430Y-114485714D01* +X125850430Y-114485714D02* +X125926620Y-114447619D01* +X125926620Y-114447619D02* +X126079001Y-114409523D01* +X126079001Y-114409523D02* +X126193287Y-114409523D01* +X126193287Y-114409523D02* +X126345668Y-114447619D01* +X126345668Y-114447619D02* +X126421859Y-114485714D01* +X126421859Y-114485714D02* +X126498049Y-114561904D01* +X126498049Y-114561904D02* +X126536144Y-114676190D01* +X126536144Y-114676190D02* +X126536144Y-114752381D01* +X126536144Y-114752381D02* +X126498049Y-114866666D01* +X126498049Y-114866666D02* +X126459954Y-114904762D01* +X125736144Y-115628571D02* +X125736144Y-115247619D01* +X125736144Y-115247619D02* +X126536144Y-115247619D01* +%TO.C,C_3V3_3*% +X140240000Y-103657836D02* +X140240000Y-103442164D01* +X140960000Y-103657836D02* +X140960000Y-103442164D01* %TO.C,SW_MACRO4*% X123700000Y-100825000D02* X123700000Y-100945000D01* @@ -1840,26 +1943,43 @@ X128100000Y-103095000D02* X128100000Y-101955000D01* X128100000Y-104225000D02* X128100000Y-104105000D01* -%TO.C,C_VIN_2*% -X126390000Y-118902836D02* -X126390000Y-118687164D01* -X127110000Y-118902836D02* -X127110000Y-118687164D01* -%TO.C,C_VIN_1*% -X124061252Y-118580000D02* -X123538748Y-118580000D01* -X124061252Y-120050000D02* -X123538748Y-120050000D01* -%TO.C,C_BUCK_OUT1*% -X130740000Y-110061252D02* -X130740000Y-109538748D01* -X132210000Y-110061252D02* -X132210000Y-109538748D01* +%TO.C,C_OLED_1*% +X123540580Y-104590000D02* +X123259420Y-104590000D01* +X123540580Y-105610000D02* +X123259420Y-105610000D01* +%TO.C,R_EN_PU1*% +X145846359Y-118220000D02* +X146153641Y-118220000D01* +X145846359Y-118980000D02* +X146153641Y-118980000D01* %TO.C,C_RGB1*% -X127642164Y-123390000D02* -X127857836Y-123390000D01* -X127642164Y-124110000D02* -X127857836Y-124110000D01* +X125440000Y-124707836D02* +X125440000Y-124492164D01* +X126160000Y-124707836D02* +X126160000Y-124492164D01* +%TO.C,SW_BOOT1*% +X145450000Y-112300000D02* +X145450000Y-116700000D01* +X145450000Y-116700000D02* +X145570000Y-116700000D01* +X145570000Y-112300000D02* +X145450000Y-112300000D01* +X146580000Y-116700000D02* +X147720000Y-116700000D01* +X147720000Y-112300000D02* +X146580000Y-112300000D01* +X148730000Y-116700000D02* +X148850000Y-116700000D01* +X148850000Y-112300000D02* +X148730000Y-112300000D01* +X148850000Y-116700000D02* +X148850000Y-112300000D01* +%TO.C,C_TRIG1*% +X131240000Y-103457836D02* +X131240000Y-103242164D01* +X131960000Y-103457836D02* +X131960000Y-103242164D01* %TO.C,SW_MACRO2*% X132800000Y-93625000D02* X132800000Y-93745000D01* @@ -1877,16 +1997,16 @@ X137200000Y-95895000D02* X137200000Y-94755000D01* X137200000Y-97025000D02* X137200000Y-96905000D01* -%TO.C,C_BUCK_IN1*% -X140211252Y-113565000D02* -X139688748Y-113565000D01* -X140211252Y-115035000D02* -X139688748Y-115035000D01* -%TO.C,C_SYS_2*% -X131890000Y-119942836D02* -X131890000Y-119727164D01* -X132610000Y-119942836D02* -X132610000Y-119727164D01* +%TO.C,C_EN1*% +X145859420Y-119790000D02* +X146140580Y-119790000D01* +X145859420Y-120810000D02* +X146140580Y-120810000D01* +%TO.C,R_USB_DM1*% +X127640000Y-114613641D02* +X127640000Y-114306359D01* +X128400000Y-114613641D02* +X128400000Y-114306359D01* %TO.C,SW_THR_UP1*% X120500000Y-72500000D02* X120500000Y-74500000D01* @@ -1967,617 +2087,47 @@ X130500000Y-124900000D01* X130800000Y-124700000D01* X130800000Y-125100000D01* G37* -%TO.C,C_BAT1*% -X133938748Y-116080000D02* -X134461252Y-116080000D01* -X133938748Y-117550000D02* -X134461252Y-117550000D01* -%TO.C,U_CHG1*% -D12* -X131800000Y-119115000D02* -G75* -G02* -X131600000Y-119115000I-100000J0D01* -G01* -X131600000Y-119115000D02* -G75* -G02* -X131800000Y-119115000I100000J0D01* -G01* %TO.C,U_OLED1*% -D11* -X121290000Y-106340000D02* -X122340000Y-106340000D01* -X121290000Y-108840000D02* -X121290000Y-106340000D01* -X122340000Y-106340000D02* -X122340000Y-105350000D01* -X122460000Y-110810000D02* -X126340000Y-110810000D01* -X127510000Y-106340000D02* -X126460000Y-106340000D01* -X127510000Y-108840000D02* -X127510000Y-106340000D01* -%TO.C,R_STAT2*% -X134196359Y-114135000D02* -X134503641Y-114135000D01* -X134196359Y-114895000D02* -X134503641Y-114895000D01* -D13* -%TO.C,LOGO3*% -G36* -X143247393Y-116934052D02* -G01* -X143377249Y-116974387D01* -X143503787Y-117047478D01* -X143631778Y-117152270D01* -X143762235Y-117289899D01* -X143856872Y-117435073D01* -X143914145Y-117568396D01* -X143934678Y-117634584D01* -X143936621Y-117680451D01* -X143919210Y-117728414D01* -X143907935Y-117750748D01* -X143854988Y-117823740D01* -X143789963Y-117872727D01* -X143722577Y-117895166D01* -X143662550Y-117888515D01* -X143619599Y-117850231D01* -X143610311Y-117828612D01* -X143545684Y-117680001D01* -X143452861Y-117544707D01* -X143339428Y-117429361D01* -X143212971Y-117340592D01* -X143081075Y-117285032D01* -X142969907Y-117268867D01* -X142871672Y-117278746D01* -X142798634Y-117312053D01* -X142747868Y-117373427D01* -X142716450Y-117467509D01* -X142701456Y-117598941D01* -X142699126Y-117698577D01* -X142702032Y-117799827D01* -X142712613Y-117893950D01* -X142733438Y-117990203D01* -X142767080Y-118097842D01* -X142816109Y-118226124D01* -X142883094Y-118384306D01* -X142900744Y-118424604D01* -X143000503Y-118653719D01* -X143081048Y-118843810D01* -X143142149Y-118994303D01* -X143183578Y-119104626D01* -X143205107Y-119174206D01* -X143208386Y-119195407D01* -X143192742Y-119267678D01* -X143151945Y-119335516D01* -X143095199Y-119392035D01* -X143031709Y-119430347D01* -X142970678Y-119443568D01* -X142921310Y-119424811D01* -X142913298Y-119416180D01* -X142893090Y-119379497D01* -X142864945Y-119315158D01* -X142843487Y-119259890D01* -X142818867Y-119197283D01* -X142779416Y-119101941D01* -X142729179Y-118983414D01* -X142672197Y-118851253D01* -X142619663Y-118731205D01* -X142537139Y-118538876D01* -X142474239Y-118378633D01* -X142428580Y-118241818D01* -X142397780Y-118119772D01* -X142379458Y-118003836D01* -X142371230Y-117885353D01* -X142370164Y-117824338D01* -X142381746Y-117622124D01* -X142420440Y-117450209D01* -X142489546Y-117299175D01* -X142592364Y-117159605D01* -X142609949Y-117140104D01* -X142741495Y-117025310D01* -X142886699Y-116953744D01* -X143050743Y-116923111D01* -X143102951Y-116921556D01* -X143247393Y-116934052D01* -G37* -G36* -X143798363Y-118218084D02* -G01* -X143801295Y-118219124D01* -X143823527Y-118231582D01* -X143838779Y-118255303D01* -X143849204Y-118299146D01* -X143856957Y-118371972D01* -X143863828Y-118476426D01* -X143881058Y-118673143D01* -X143910704Y-118857650D01* -X143956281Y-119047424D01* -X144021282Y-119259890D01* -X144091527Y-119456879D01* -X144164019Y-119622306D01* -X144245927Y-119767066D01* -X144344417Y-119902052D01* -X144466656Y-120038159D01* -X144619810Y-120186282D01* -X144647295Y-120211489D01* -X144830428Y-120382039D01* -X144979421Y-120529278D01* -X145097493Y-120657261D01* -X145187861Y-120770043D01* -X145253742Y-120871680D01* -X145298355Y-120966227D01* -X145324917Y-121057738D01* -X145326914Y-121068008D01* -X145329066Y-121195135D01* -X145288029Y-121311736D01* -X145205980Y-121416585D01* -X145085095Y-121508454D01* -X144927551Y-121586118D01* -X144735525Y-121648349D01* -X144511192Y-121693922D01* -X144256730Y-121721608D01* -X144157702Y-121726979D01* -X144016513Y-121730877D01* -X143912551Y-121729001D01* -X143837038Y-121720863D01* -X143781230Y-121705986D01* -X143692720Y-121665751D01* -X143643176Y-121623831D01* -X143625504Y-121573770D01* -X143625159Y-121564006D01* -X143646217Y-121486648D01* -X143701188Y-121420220D01* -X143777767Y-121372761D01* -X143863650Y-121352312D01* -X143934325Y-121362011D01* -X144059909Y-121390945D01* -X144216615Y-121402870D01* -X144392724Y-121398353D01* -X144576516Y-121377961D01* -X144756270Y-121342260D01* -X144843590Y-121318039D01* -X144988477Y-121273288D01* -X144960920Y-121193712D01* -X144918047Y-121101863D01* -X144847691Y-120997634D01* -X144747154Y-120877850D01* -X144613741Y-120739334D01* -X144444754Y-120578911D01* -X144418520Y-120554902D01* -X144269663Y-120416864D01* -X144150845Y-120300340D01* -X144055928Y-120197932D01* -X143978779Y-120102241D01* -X143913260Y-120005869D01* -X143853238Y-119901417D01* -X143814999Y-119827164D01* -X143677663Y-119505334D01* -X143582648Y-119173640D01* -X143528208Y-118825290D01* -X143516861Y-118669171D01* -X143511399Y-118551617D01* -X143509624Y-118470569D01* -X143512855Y-118416284D01* -X143522410Y-118379019D01* -X143539609Y-118349033D01* -X143564358Y-118318261D01* -X143640781Y-118250093D01* -X143722531Y-118215132D01* -X143798363Y-118218084D01* -G37* -G36* -X141326561Y-118895119D02* -G01* -X141465752Y-118937431D01* -X141642850Y-119001800D01* -X141858496Y-119088453D01* -X142113330Y-119197619D01* -X142305378Y-119283047D01* -X142442143Y-119341846D01* -X142597564Y-119404311D01* -X142748987Y-119461514D01* -X142836292Y-119492239D01* -X142941027Y-119529938D01* -X143029798Y-119566327D01* -X143093144Y-119597228D01* -X143121488Y-119618241D01* -X143126830Y-119670422D01* -X143102327Y-119736746D01* -X143055613Y-119804159D01* -X142994320Y-119859601D01* -X142972684Y-119872784D01* -X142887483Y-119918404D01* -X142628691Y-119831009D01* -X142509598Y-119788268D01* -X142364988Y-119732521D01* -X142211321Y-119670315D01* -X142065060Y-119608198D01* -X142033650Y-119594368D01* -X141919082Y-119543713D01* -X141820331Y-119500424D01* -X141744708Y-119467675D01* -X141699521Y-119448643D01* -X141689991Y-119445122D01* -X141693087Y-119463897D01* -X141710024Y-119510493D01* -X141716131Y-119525418D01* -X141739197Y-119599065D01* -X141749629Y-119668799D01* -X141749681Y-119672655D01* -X141749681Y-119739597D01* -X141940702Y-119752418D01* -X142097539Y-119771630D01* -X142249343Y-119806074D01* -X142388554Y-119852543D01* -X142507615Y-119907828D01* -X142598966Y-119968720D01* -X142655048Y-120032011D01* -X142666816Y-120060621D01* -X142665443Y-120128569D01* -X142639233Y-120209874D01* -X142596668Y-120286570D01* -X142546231Y-120340689D01* -X142530099Y-120350176D01* -X142493529Y-120359856D01* -X142452780Y-120350769D01* -X142394916Y-120318744D01* -X142358536Y-120294855D01* -X142212994Y-120219459D01* -X142043051Y-120167731D01* -X141866420Y-120144092D01* -X141760138Y-120145574D01* -X141692356Y-120152259D01* -X141640824Y-120163524D01* -X141594049Y-120185388D01* -X141540538Y-120223868D01* -X141468797Y-120284982D01* -X141432271Y-120317248D01* -X141329569Y-120408077D01* -X141214227Y-120509832D01* -X141106598Y-120604564D01* -X141076918Y-120630631D01* -X140951615Y-120747266D01* -X140861352Y-120846068D01* -X140807387Y-120925322D01* -X140790978Y-120983315D01* -X140800055Y-121007649D01* -X140847957Y-121044983D01* -X140921437Y-121068771D01* -X141025428Y-121079559D01* -X141164863Y-121077892D01* -X141327338Y-121065953D01* -X141459221Y-121054689D01* -X141552442Y-121049429D01* -X141614258Y-121050176D01* -X141651925Y-121056934D01* -X141668860Y-121066088D01* -X141696853Y-121116348D01* -X141701953Y-121190780D01* -X141685183Y-121273897D01* -X141650384Y-121346119D01* -X141622476Y-121383925D01* -X141592825Y-121408935D01* -X141550149Y-121425727D01* -X141483161Y-121438875D01* -X141389901Y-121451746D01* -X141200174Y-121471394D01* -X141032222Y-121478838D01* -X140892693Y-121474140D01* -X140788234Y-121457363D01* -X140754221Y-121445795D01* -X140631944Y-121371817D01* -X140548704Y-121274747D01* -X140505443Y-121157816D01* -X140503098Y-121024255D01* -X140542610Y-120877296D01* -X140570754Y-120814664D01* -X140617531Y-120731173D01* -X140676493Y-120646303D01* -X140752266Y-120554950D01* -X140849475Y-120452010D01* -X140972745Y-120332379D01* -X141126704Y-120190951D01* -X141176429Y-120146314D01* -X141297133Y-120035637D01* -X141387875Y-119946436D01* -X141446584Y-119880886D01* -X141471185Y-119841159D01* -X141471832Y-119836742D01* -X141461828Y-119794502D01* -X141435465Y-119725567D01* -X141398215Y-119644083D01* -X141393991Y-119635565D01* -X141350575Y-119543970D01* -X141312016Y-119454403D01* -X141287000Y-119387237D01* -X141262639Y-119317499D01* -X141235884Y-119276498D01* -X141192842Y-119251612D01* -X141119623Y-119230221D01* -X141112022Y-119228277D01* -X141042369Y-119204718D01* -X140991366Y-119177005D01* -X140978269Y-119164033D01* -X140964856Y-119103384D01* -X140984548Y-119032198D01* -X141029903Y-118962318D01* -X141093485Y-118905587D01* -X141159345Y-118875755D01* -X141224639Y-118874636D01* -X141326561Y-118895119D01* -G37* -G36* -X143550775Y-115479626D02* -G01* -X143793163Y-115528624D01* -X144003620Y-115610254D01* -X144182836Y-115724750D01* -X144263406Y-115796848D01* -X144375653Y-115930856D01* -X144463026Y-116085929D01* -X144527635Y-116267796D01* -X144571588Y-116482190D01* -X144594444Y-116696527D01* -X144609207Y-116902389D01* -X144882353Y-117025883D01* -X145009342Y-117086724D01* -X145135462Y-117153225D01* -X145253337Y-117220851D01* -X145355591Y-117285064D01* -X145434846Y-117341329D01* -X145483727Y-117385110D01* -X145495168Y-117402732D01* -X145481670Y-117403716D01* -X145437348Y-117382707D01* -X145369747Y-117343640D01* -X145311861Y-117307166D01* -X145205961Y-117240660D01* -X145100439Y-117178265D01* -X145003928Y-117124692D01* -X144925061Y-117084652D01* -X144872469Y-117062857D01* -X144859443Y-117060254D01* -X144870093Y-117070702D01* -X144913272Y-117098716D01* -X144981068Y-117139303D01* -X145022903Y-117163422D01* -X145130430Y-117228313D01* -X145229920Y-117294905D01* -X145313937Y-117357538D01* -X145375042Y-117410551D01* -X145405799Y-117448283D01* -X145408021Y-117456536D01* -X145391110Y-117457144D01* -X145347342Y-117435278D01* -X145301490Y-117405957D01* -X145240539Y-117368769D01* -X145149851Y-117319169D01* -X145040598Y-117262668D01* -X144923948Y-117204777D01* -X144811073Y-117151008D01* -X144713142Y-117106873D01* -X144641327Y-117077883D01* -X144626718Y-117073016D01* -X144589848Y-117067112D01* -X144586231Y-117086474D01* -X144588731Y-117093617D01* -X144614650Y-117120439D01* -X144671616Y-117160355D01* -X144749034Y-117206203D01* -X144779607Y-117222643D01* -X144880681Y-117279177D01* -X144982580Y-117342367D01* -X145078083Y-117406952D01* -X145159974Y-117467667D01* -X145221035Y-117519251D01* -X145254046Y-117556440D01* -X145256892Y-117570660D01* -X145230699Y-117574416D01* -X145184854Y-117548097D01* -X145183317Y-117546897D01* -X145126430Y-117511590D01* -X145082125Y-117500861D01* -X145061175Y-117516883D01* -X145060711Y-117522154D01* -X145041687Y-117528959D01* -X144984388Y-117511836D01* -X144888474Y-117470650D01* -X144753607Y-117405267D01* -X144713400Y-117384940D01* -X144542533Y-117302473D01* -X144342353Y-117213124D01* -X144127757Y-117123020D01* -X143939893Y-117048677D01* -X144806016Y-117048677D01* -X144817593Y-117060254D01* -X144829170Y-117048677D01* -X144817593Y-117037100D01* -X144806016Y-117048677D01* -X143939893Y-117048677D01* -X143913640Y-117038288D01* -X143878997Y-117025523D01* -X144759708Y-117025523D01* -X144771285Y-117037100D01* -X144782862Y-117025523D01* -X144771285Y-117013946D01* -X144759708Y-117025523D01* -X143878997Y-117025523D01* -X143816159Y-117002369D01* -X144713400Y-117002369D01* -X144724977Y-117013946D01* -X144736554Y-117002369D01* -X144724977Y-116990792D01* -X144713400Y-117002369D01* -X143816159Y-117002369D01* -X143753321Y-116979215D01* -X144667092Y-116979215D01* -X144678669Y-116990792D01* -X144690246Y-116979215D01* -X144678669Y-116967638D01* -X144667092Y-116979215D01* -X143753321Y-116979215D01* -X143714897Y-116965057D01* -X143592051Y-116923646D01* -X143439522Y-116878180D01* -X143272965Y-116834194D01* -X143099428Y-116793002D01* -X142925960Y-116755919D01* -X142759607Y-116724258D01* -X142607420Y-116699332D01* -X142476444Y-116682455D01* -X142373730Y-116674941D01* -X142306324Y-116678103D01* -X142293354Y-116681588D01* -X142264211Y-116685338D01* -X142261699Y-116675777D01* -X142273690Y-116645238D01* -X142297480Y-116583397D01* -X142324255Y-116513264D01* -X142539506Y-116513264D01* -X142547567Y-116549363D01* -X142584981Y-116571633D01* -X142640299Y-116568951D01* -X142693953Y-116543571D01* -X142707687Y-116530902D01* -X142745951Y-116469519D01* -X142772969Y-116391952D01* -X142782459Y-116319521D01* -X142778367Y-116290913D01* -X142748041Y-116256540D01* -X142698149Y-116252569D01* -X142642622Y-116277425D01* -X142608670Y-116310096D01* -X142572439Y-116372992D01* -X142547860Y-116446682D01* -X142539506Y-116513264D01* -X142324255Y-116513264D01* -X142328459Y-116502253D01* -X142336517Y-116481066D01* -X142388961Y-116344920D01* -X142429122Y-116246704D01* -X142460257Y-116180729D01* -X142485624Y-116141302D01* -X142508481Y-116122734D01* -X142532084Y-116119331D01* -X142542630Y-116120977D01* -X142564726Y-116125756D01* -X142597814Y-116133193D01* -X142646962Y-116144466D01* -X142717239Y-116160752D01* -X142813715Y-116183229D01* -X142941458Y-116213074D01* -X143105538Y-116251465D01* -X143250226Y-116285341D01* -X143347488Y-116315133D01* -X143478888Y-116366258D01* -X143638778Y-116436355D01* -X143821510Y-116523060D01* -X143837920Y-116531123D01* -X144256427Y-116737285D01* -X144242360Y-116649864D01* -X144189610Y-116434843D01* -X144105133Y-116253094D01* -X143987470Y-116102843D01* -X143835167Y-115982319D01* -X143646766Y-115889748D01* -X143605402Y-115874701D01* -X143534634Y-115852451D01* -X143466395Y-115837299D01* -X143389116Y-115827957D01* -X143291224Y-115823139D01* -X143161150Y-115821556D01* -X143127347Y-115821515D01* -X142994818Y-115822181D01* -X142897682Y-115825128D01* -X142825030Y-115831780D01* -X142765953Y-115843564D01* -X142709546Y-115861904D01* -X142657435Y-115882918D01* -X142567787Y-115923836D01* -X142482971Y-115967752D01* -X142431416Y-115998686D01* -X142394723Y-116026817D01* -X142356446Y-116063653D01* -X142315118Y-116111807D01* -X142269271Y-116173890D01* -X142217439Y-116252516D01* -X142158152Y-116350296D01* -X142089943Y-116469843D01* -X142011345Y-116613769D01* -X141920890Y-116784687D01* -X141817110Y-116985210D01* -X141698538Y-117217949D01* -X141563706Y-117485517D01* -X141411147Y-117790526D01* -X141304789Y-118004051D01* -X141175116Y-118263373D01* -X141064111Y-118482407D01* -X140970875Y-118662836D01* -X140894505Y-118806342D01* -X140834100Y-118914607D01* -X140788759Y-118989313D01* -X140757580Y-119032143D01* -X140749514Y-119040195D01* -X140674157Y-119086521D01* -X140607651Y-119095325D01* -X140557403Y-119066507D01* -X140542855Y-119042995D01* -X140535979Y-119017767D01* -X140538302Y-118984601D01* -X140552200Y-118936935D01* -X140580050Y-118868206D01* -X140624226Y-118771849D01* -X140687105Y-118641301D01* -X140691635Y-118632011D01* -X140865392Y-118275842D01* -X140809724Y-118254007D01* -X140767716Y-118225032D01* -X140754155Y-118196122D01* -X140764078Y-118167156D01* -X140791736Y-118103183D01* -X140834036Y-118010557D01* -X140887887Y-117895632D01* -X140950197Y-117764762D01* -X141017873Y-117624301D01* -X141087824Y-117480604D01* -X141156959Y-117340022D01* -X141222184Y-117208912D01* -X141280409Y-117093626D01* -X141328541Y-117000519D01* -X141363488Y-116935944D01* -X141381400Y-116907121D01* -X141432997Y-116880452D01* -X141488301Y-116879988D01* -X141519628Y-116882481D01* -X141544836Y-116877397D01* -X141569071Y-116858533D01* -X141597479Y-116819687D01* -X141635206Y-116754657D01* -X141687397Y-116657241D01* -X141712360Y-116609935D01* -X141805670Y-116434769D01* -X141882968Y-116294596D01* -X141948559Y-116182798D01* -X142006750Y-116092756D01* -X142061847Y-116017851D01* -X142118156Y-115951464D01* -X142179983Y-115886977D01* -X142187653Y-115879372D01* -X142383224Y-115717055D01* -X142600794Y-115594896D01* -X142841165Y-115512589D01* -X143105135Y-115469828D01* -X143275764Y-115463027D01* -X143550775Y-115479626D01* -G37* -%TO.C,R_FB2*% -D11* -X133586359Y-106345000D02* -X133893641Y-106345000D01* -X133586359Y-107105000D02* -X133893641Y-107105000D01* +X121290000Y-108340000D02* +X122340000Y-108340000D01* +X121290000Y-110840000D02* +X121290000Y-108340000D01* +X122340000Y-108340000D02* +X122340000Y-107350000D01* +X122460000Y-112810000D02* +X126340000Y-112810000D01* +X127510000Y-108340000D02* +X126460000Y-108340000D01* +X127510000Y-110840000D02* +X127510000Y-108340000D01* +%TO.C,C_OLED_2*% +X123507836Y-105940000D02* +X123292164Y-105940000D01* +X123507836Y-106660000D02* +X123292164Y-106660000D01* +%TO.C,U_MCU1*% +X128650000Y-104650000D02* +X129700000Y-104650000D01* +X128650000Y-105700000D02* +X128650000Y-104650000D01* +X128650000Y-119300000D02* +X128650000Y-120350000D01* +X128650000Y-120350000D02* +X129700000Y-120350000D01* +X128800000Y-104800000D02* +X144200000Y-104800000D01* +X128800000Y-120200000D02* +X128800000Y-104800000D01* +X144200000Y-104800000D02* +X144200000Y-120200000D01* +X144200000Y-120200000D02* +X128800000Y-120200000D01* +X144350000Y-105700000D02* +X144350000Y-104500000D01* +X144350000Y-119300000D02* +X144350000Y-120350000D01* +X144350000Y-120350000D02* +X143300000Y-120350000D01* %TO.C,SW_VOL_DN1*% X146700000Y-81100000D02* X147700000Y-81100000D01* @@ -2600,11 +2150,6 @@ X141700000Y-125250000D02* X141700000Y-127250000D01* X141700000Y-129150000D02* X141700000Y-131050000D01* -%TO.C,R_VSET1*% -X122413641Y-115120000D02* -X122106359Y-115120000D01* -X122413641Y-115880000D02* -X122106359Y-115880000D01* %TO.C,J_STICK1*% D12* X136000000Y-78500000D02* @@ -2634,32 +2179,37 @@ X128425000Y-85075000D01* X128425000Y-71925000D01* X130250000Y-71925000D01* X130250000Y-69100000D01* -%TO.C,R_STAT1*% -D11* -X125313641Y-116935000D02* -X125006359Y-116935000D01* -X125313641Y-117695000D02* -X125006359Y-117695000D01* -%TO.C,R_ISET1*% -X122433641Y-116135000D02* -X122126359Y-116135000D01* -X122433641Y-116895000D02* -X122126359Y-116895000D01* %TO.C,C_DBNC1*% +D11* X123707836Y-124840000D02* X123492164Y-124840000D01* X123707836Y-125560000D02* X123492164Y-125560000D01* %TO.C,R_RGB1*% -X127596359Y-122220000D02* -X127903641Y-122220000D01* -X127596359Y-122980000D02* -X127903641Y-122980000D01* -%TO.C,R_FB1*% -X131595000Y-106396359D02* -X131595000Y-106703641D01* -X132355000Y-106396359D02* -X132355000Y-106703641D01* +X127520000Y-123143641D02* +X127520000Y-122836359D01* +X128280000Y-123143641D02* +X128280000Y-122836359D01* +%TO.C,C_3V3_2*% +X140240000Y-101707836D02* +X140240000Y-101492164D01* +X140960000Y-101707836D02* +X140960000Y-101492164D01* +%TO.C,C_3V3_1*% +X144790000Y-106140580D02* +X144790000Y-105859420D01* +X145810000Y-106140580D02* +X145810000Y-105859420D01* +%TO.C,R_VSYS1*% +X129420000Y-101256359D02* +X129420000Y-101563641D01* +X130180000Y-101256359D02* +X130180000Y-101563641D01* +%TO.C,R_I2C_SDA1*% +X125120000Y-105636359D02* +X125120000Y-105943641D01* +X125880000Y-105636359D02* +X125880000Y-105943641D01* %TO.C,SW_THR_DN1*% X120500000Y-82500000D02* X120500000Y-84500000D01* @@ -2671,6 +2221,11 @@ X123300000Y-85300000D02* X123300000Y-85900000D01* X123300000Y-85900000D02* X122300000Y-85900000D01* +%TO.C,R_I2C_SCL1*% +X126820000Y-106746359D02* +X126820000Y-107053641D01* +X127580000Y-106746359D02* +X127580000Y-107053641D01* %TO.C,SW_VOL_UP1*% X146700000Y-71100000D02* X147700000Y-71100000D01* @@ -2682,49 +2237,11 @@ X146700000Y-75900000D02* X147700000Y-75900000D01* X149500000Y-74500000D02* X149500000Y-72500000D01* -%TO.C,U_BUCK1*% -X139365000Y-110027500D02* -X139415000Y-110027500D01* -X139365000Y-111847500D02* -X139365000Y-110027500D01* -X139415000Y-111847500D02* -X139365000Y-111847500D01* -X141315000Y-111847500D02* -X140535000Y-111847500D01* -X142435000Y-110027500D02* -X142485000Y-110027500D01* -X142485000Y-110027500D02* -X142485000Y-111847500D01* -X142485000Y-111847500D02* -X142435000Y-111847500D01* -X142435000Y-109487500D02* -X142765000Y-109247500D01* -X142765000Y-109727500D01* -X142435000Y-109487500D01* -G36* -X142765000Y-109727500D02* -G01* -X142435000Y-109487500D01* -X142765000Y-109247500D01* -X142765000Y-109727500D01* -G37* -%TO.C,L_BUCK1*% -X133590000Y-107690000D02* -X133590000Y-108715000D01* -X133590000Y-107690000D02* -X134615000Y-107690000D01* -X133590000Y-111910000D02* -X133590000Y-110885000D01* -X133590000Y-111910000D02* -X134615000Y-111910000D01* -X138360000Y-107690000D02* -X137335000Y-107690000D01* -X138360000Y-107690000D02* -X138360000Y-108715000D01* -X138360000Y-111910000D02* -X137335000Y-111910000D01* -X138360000Y-111910000D02* -X138360000Y-110885000D01* +%TO.C,R_VSYS2*% +X129620000Y-103246359D02* +X129620000Y-103553641D01* +X130380000Y-103246359D02* +X130380000Y-103553641D01* %TO.C,SW_PWR1*% X120600000Y-126400000D02* X120600000Y-127400000D01* @@ -2736,6 +2253,11 @@ X124800000Y-126400000D02* X125400000Y-126400000D01* X125400000Y-126400000D02* X125400000Y-127400000D01* +%TO.C,R_USB_DP1*% +X127640000Y-116553641D02* +X127640000Y-116246359D01* +X128400000Y-116553641D02* +X128400000Y-116246359D01* %TO.C,SW_MACRO5*% X132800000Y-100825000D02* X132800000Y-100945000D01* @@ -2753,10 +2275,10 @@ X137200000Y-103095000D02* X137200000Y-101955000D01* X137200000Y-104225000D02* X137200000Y-104105000D01* -%TO.C,R_TS1*% -X122413641Y-114120000D02* -X122106359Y-114120000D01* -X122413641Y-114880000D02* -X122106359Y-114880000D01* +%TO.C,R_BOOT_PU1*% +X145420000Y-109563641D02* +X145420000Y-109256359D01* +X146180000Y-109563641D02* +X146180000Y-109256359D01* %TD*% M02* diff --git a/PCB/v2.x/production/gerbers/snips_controller-In1_Cu.gbr b/PCB/v2.x/production/gerbers/snips_controller-In1_Cu.gbr index faff37c..1d177de 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-In1_Cu.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-In1_Cu.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Copper,L2,Inr*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -30,64 +30,52 @@ G04 Aperture macros list* 20,1,$1+$1,$8,$9,$2,$3,0*% G04 Aperture macros list end* %TA.AperFunction,ComponentPad*% -%ADD10C,0.300000*% +%ADD10O,1.000000X2.100000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD11O,1.000000X2.100000*% +%ADD11O,1.000000X1.600000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD12O,1.000000X1.600000*% +%ADD12C,2.550000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD13C,2.550000*% +%ADD13C,2.050000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD14C,2.050000*% +%ADD14C,2.250000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD15C,2.250000*% +%ADD15RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD16RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% +%ADD16O,1.200000X1.750000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD17O,1.200000X1.750000*% +%ADD17C,0.300000*% %TD*% %TA.AperFunction,ViaPad*% %ADD18C,0.600000*% %TD*% -%TA.AperFunction,Conductor*% -%ADD19C,0.400000*% -%TD*% -%TA.AperFunction,Conductor*% -%ADD20C,0.200000*% -%TD*% G04 APERTURE END LIST* D10* %TO.N,GND*% -%TO.C,U_CHG1*% -X129750000Y-118815000D03* -X129750000Y-117815000D03* -%TD*% -D11* -%TO.N,GND*% %TO.C,J_USB1*% X132680000Y-124020000D03* -D12* -X132680000Y-128200000D03* D11* +X132680000Y-128200000D03* +D10* X141320000Y-124020000D03* -D12* +D11* X141320000Y-128200000D03* %TD*% -D13* +D12* %TO.N,*% %TO.C,J_STICK1*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D14* +D13* %TO.N,GND*% X137500000Y-69770000D03* X143730000Y-81000000D03* @@ -95,10 +83,10 @@ X143730000Y-81000000D03* X135000000Y-69770000D03* %TO.N,/MCU_Core/STICK_Y*% X143730000Y-78500000D03* -%TO.N,/MCU_Core/3V3_RF*% +%TO.N,3V3*% X132500000Y-69770000D03* X143730000Y-76000000D03* -D15* +D14* %TO.N,/MCU_Core/BTN_STICK*% X131750000Y-84250000D03* %TO.N,N/C*% @@ -108,348 +96,175 @@ X131750000Y-88750000D03* %TO.N,N/C*% X138250000Y-88750000D03* %TD*% -D16* +D15* %TO.N,VBAT*% %TO.C,BT1*% X145200000Y-123100000D03* -D17* +D16* %TO.N,GND*% X147200000Y-123100000D03* %TD*% +D17* +%TO.N,GND*% +%TO.C,U_CHG1*% +X128750000Y-95750000D03* +X128750000Y-96750000D03* +%TD*% D18* -%TO.N,VSYS*% -X131134999Y-72039999D03* -X133551500Y-90667500D03* -X131197200Y-105109200D03* -X135775300Y-108336200D03* -X127561250Y-90824999D03* +%TO.N,3V3*% +X127761250Y-93014999D03* +X145311599Y-107614004D03* +X136012023Y-99792121D03* +X131100000Y-101100000D03* +X132248535Y-126920005D03* +X127200000Y-127762500D03* +X124950000Y-104123528D03* +X134200000Y-106400000D03* +X125080000Y-124896016D03* +X123900000Y-98100000D03* +X141068110Y-104176936D03* +X130620864Y-129450000D03* +X129000000Y-64600000D03* +X126320000Y-106400000D03* +X145500000Y-117780000D03* +X138500000Y-93250000D03* +X137400000Y-100200000D03* %TO.N,GND*% -X144000000Y-94500000D03* -X131800000Y-124350000D03* -X130449999Y-67550000D03* -X143750000Y-70550000D03* -X123950000Y-83200000D03* -X121300000Y-107150000D03* -X142800000Y-95850000D03* -X139100000Y-103700000D03* -X122350000Y-105150000D03* -X131800000Y-96500000D03* -X136300000Y-95300000D03* -X121750000Y-119315000D03* -X122600000Y-125750000D03* -X128750000Y-124300000D03* -X123150000Y-85600000D03* -X123050000Y-95850000D03* -X140500000Y-108600000D03* -X128750000Y-103050000D03* -X122600000Y-124650000D03* -X146500000Y-67450000D03* -X135250000Y-106825000D03* -X140800000Y-122150000D03* -X142850000Y-95000000D03* -X136250000Y-117315000D03* -X134600000Y-103700000D03* -X130500000Y-92300000D03* -X129870634Y-119615000D03* -X131450000Y-117565000D03* -X145300000Y-75100000D03* -X136400000Y-100400000D03* -X140000000Y-69400000D03* -X134700000Y-63950000D03* -X135450000Y-103800000D03* -X137850000Y-104150000D03* -X133000000Y-119265000D03* -X129000000Y-96550000D03* -X148500000Y-83050000D03* +X140600000Y-118700000D03* +X126900000Y-123500000D03* +X128300000Y-97700000D03* +X128700000Y-100300000D03* +X139600000Y-114100000D03* +X130850000Y-97425000D03* +X130700000Y-63800000D03* +X139100000Y-70700000D03* +X132500000Y-67000000D03* +X145400000Y-88100000D03* +X137500000Y-97750000D03* +X135250000Y-97250000D03* +X124200000Y-71800000D03* +X134900000Y-64600000D03* +X147050000Y-96950000D03* +X146248528Y-83299999D03* +X124200000Y-64800000D03* +X145600000Y-73000000D03* +X124750000Y-96250000D03* +X131300000Y-117800000D03* +X130800000Y-106700000D03* +X122600000Y-104000000D03* +X142000000Y-114200000D03* +X124100000Y-83700000D03* +X140400000Y-100300000D03* +X121800000Y-96700000D03* +X137799998Y-103000000D03* +X135250000Y-95750000D03* X136285000Y-75940000D03* -X144550000Y-69350000D03* -X143300000Y-102350000D03* -X143200000Y-90650000D03* -X132150000Y-104150000D03* -X130449999Y-103700000D03* -X141700000Y-70000000D03* -X137400000Y-125800000D03* -X123950000Y-73200000D03* -X137450000Y-114300000D03* -X129770634Y-116815000D03* -X131900000Y-100400000D03* -X144950000Y-110700000D03* -X148500000Y-73050000D03* -X143300000Y-106450000D03* -X137050000Y-92150000D03* +X131800000Y-100500000D03* +X128349799Y-95084604D03* +X132000000Y-95300000D03* X131785000Y-73440000D03* -X142800000Y-103050000D03* -X136050000Y-101250000D03* -X141950000Y-79700000D03* -X129800000Y-64050000D03* -X139850000Y-87250000D03* -X145350000Y-93100000D03* -X130950000Y-107800000D03* -X142800000Y-126600000D03* -X146350000Y-66599999D03* -X145450000Y-95800000D03* -X134550000Y-101250000D03* -X147450000Y-106450000D03* -X123050000Y-103050000D03* -X136250000Y-118815000D03* -X147450000Y-102350000D03* -X142900000Y-67400000D03* -X145400000Y-103050000D03* -X123000000Y-104550000D03* -X133199999Y-122150000D03* -X130400000Y-126300000D03* -X125750000Y-118315000D03* -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X129800000Y-100700000D03* -%TO.N,VBUS*% -X125770000Y-125525300D03* -X134650000Y-121702500D03* -X139450000Y-121868900D03* -X141321300Y-92762500D03* -X141703000Y-89578400D03* -X149218700Y-96601800D03* -%TO.N,3V3*% -X131950000Y-112300000D03* -X127300000Y-121550001D03* -X123900000Y-113658400D03* -X146120300Y-98555000D03* -X124549200Y-107406100D03* -X123860000Y-116915000D03* -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X131797000Y-95119100D03* +X122500000Y-125200000D03* +%TO.N,/MCU_Core/MCU_BOOT*% +X139900000Y-106400000D03* +X144900000Y-108300000D03* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X130070634Y-92600000D03* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X124754600Y-83434100D03* -X132620800Y-86688200D03* +X121873930Y-107063387D03* +X130300000Y-116600000D03* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X139209300Y-100184300D03* -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X139789800Y-98443100D03* +X141300000Y-106600000D03* +X142600000Y-102400000D03* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X129065000Y-94095500D03* -%TO.N,VBAT*% -X133810600Y-118937400D03* -%TO.N,/MCU_Core/STAT2*% -X130387500Y-96500000D03* -%TO.N,/MCU_Core/STAT1*% -X123374265Y-117590735D03* +X128200000Y-105450002D03* +X130400000Y-109900000D03* %TO.N,/Accelerometer/I2C_SDA*% -X132254800Y-65652100D03* -X124959600Y-104749000D03* +X124200000Y-111600000D03* +X124600000Y-109800000D03* +X121874741Y-124680758D03* %TO.N,/Accelerometer/I2C_SCL*% -X121327800Y-96462500D03* -X126003900Y-70995100D03* -X126735300Y-100400000D03* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X145804700Y-84769200D03* -%TO.N,/USB_C/USB_CC1*% -X135750000Y-121500900D03* -%TO.N,/MCU_Core/USB_DP*% -X148072200Y-111842500D03* -X139484600Y-96501700D03* -%TO.N,/MCU_Core/USB_DM*% -X137901700Y-95241600D03* -%TO.N,/USB_C/USB_CC2*% -X138750000Y-126065000D03* -%TO.N,/MCU_Core/STICK_X*% -X126670100Y-93676600D03* -%TO.N,/MCU_Core/STICK_Y*% -X130207300Y-95609600D03* -%TO.N,/MCU_Core/3V3_RF*% -X142999700Y-92385900D03* +X125800000Y-109700000D03* +X122700000Y-114100000D03* +X121100000Y-124880210D03* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X138900000Y-106200000D03* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X133300000Y-100800000D03* +X133100000Y-107000000D03* +X136161765Y-101138235D03* +%TO.N,/MCU_Core/STAT2*% +X130824265Y-108075735D03* +%TO.N,/MCU_Core/STAT1*% +X130800000Y-108900000D03* +X127500000Y-99000000D03* +X126150000Y-97470100D03* %TO.N,/MCU_Core/BTN_STICK*% -X134709100Y-92787200D03* +X130500000Y-110800000D03* +X126600000Y-100400000D03* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X145452900Y-98045000D03* -X120688600Y-97070100D03* +X120600000Y-125765642D03* +X130500000Y-114200000D03* +X124000000Y-119600000D03* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X131000000Y-62700000D03* +X122300000Y-87800000D03* +X131700000Y-115100000D03* +X124500000Y-67800000D03* +X121893900Y-106234827D03* +%TO.N,/XBee/XBEE_CTS*% +X127800000Y-117800000D03* %TO.N,/MCU_Core/RGB_DIN*% -X129216700Y-123115100D03* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X123557800Y-90439600D03* -%TO.N,/Buttons_Direct/BTN_VOL_UP*% -X135734500Y-92661400D03* -%TO.N,/Power_Buck/PWR_EN*% -X145850800Y-107623700D03* -X145980700Y-85815700D03* -X141116700Y-110981600D03* -%TO.N,/Buttons_Direct/BTN_MACRO5*% -X136150000Y-104250000D03* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X127525700Y-92504700D03* -X129861700Y-101982200D03* +X126002198Y-123340339D03* +X130400000Y-117400000D03* +%TO.N,/XBee/XBEE_DIN*% +X130179998Y-120689999D03* +%TO.N,/XBee/XBEE_DOUT*% +X131615136Y-118535318D03* %TO.N,ACCEL_INT1*% -X129871400Y-99693700D03* -X139636800Y-97508700D03* -X147014800Y-76170200D03* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X134775000Y-95096400D03* -X135000000Y-61269100D03* -X134105300Y-87305100D03* +X139400000Y-116900000D03* +%TO.N,/Buttons_Direct/BTN_VOL_UP*% +X147034358Y-98156239D03* +X133000000Y-118200000D03* +%TO.N,/XBee/XBEE_RTS*% +X133900000Y-118200000D03* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147700000Y-98600000D03* +X134700000Y-117700000D03* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135600000Y-118300000D03* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-118300000D03* %TO.N,/MCU_Core/PWR_HOLD*% +X140950000Y-90700000D03* X138485000Y-72539999D03* -X129625000Y-98237500D03* -%TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127260700Y-66852300D03* -X126692500Y-80628700D03* -%TD*% -%TO.N,VSYS*% -D19* -X127561000Y-90825000D02* -X133394000Y-90825000D01* -X133394000Y-90825000D02* -X133551500Y-90667500D01* +X142000000Y-107300000D03* %TO.N,VBUS*% -X141703000Y-92380800D02* -X141321300Y-92762500D01* -X135150200Y-122202700D02* -X139116200Y-122202700D01* -X142558000Y-96601800D02* -X149218700Y-96601800D01* -X141321300Y-95365100D02* -X142558000Y-96601800D01* -X125770000Y-125525300D02* -X129847000Y-121448300D01* -X134650000Y-121702500D02* -X135150200Y-122202700D01* -X129847000Y-121448300D02* -X134395800Y-121448300D01* -X141321300Y-92762500D02* -X141321300Y-95365100D01* -X141703000Y-89578400D02* -X141703000Y-92380800D01* -X139116200Y-122202700D02* -X139450000Y-121868900D01* -X134395800Y-121448300D02* -X134650000Y-121702500D01* -%TO.N,3V3*% -D20* -X124665200Y-118915200D02* -X124665200Y-117720200D01* -X131950000Y-112300000D02* -X125258400Y-112300000D01* -X124549200Y-107406100D02* -X127653300Y-107406100D01* -X127653300Y-107406100D02* -X132442900Y-102616500D01* -X123860000Y-116915000D02* -X123860000Y-113698400D01* -X132442900Y-102616500D02* -X142058800Y-102616500D01* -X142058800Y-102616500D02* -X146120300Y-98555000D01* -X124665200Y-117720200D02* -X123860000Y-116915000D01* -X125258400Y-112300000D02* -X123900000Y-113658400D01* -X127300000Y-121550000D02* -X124665200Y-118915200D01* -X123860000Y-113698400D02* -X123900000Y-113658400D01* -%TO.N,/Buttons_Direct/BTN_THR_UP*% -X132620800Y-86688200D02* -X128008700Y-86688200D01* -X128008700Y-86688200D02* -X124754600Y-83434100D01* -%TO.N,/Accelerometer/I2C_SCL*% -X121327800Y-96462500D02* -X122797800Y-96462500D01* -X122797800Y-96462500D02* -X126735300Y-100400000D01* -%TO.N,/MCU_Core/USB_DP*% -X148412500Y-111502200D02* -X148412500Y-99949900D01* -X148072200Y-111842500D02* -X148412500Y-111502200D01* -X145905900Y-97443300D02* -X140426200Y-97443300D01* -X148412500Y-99949900D02* -X145905900Y-97443300D01* -X140426200Y-97443300D02* -X139484600Y-96501700D01* -%TO.N,/MCU_Core/3V3_RF*% -D19* -X143730000Y-76000000D02* -X145156700Y-77426700D01* -X145156700Y-77426700D02* -X145156700Y-83964000D01* -X145103000Y-84017700D02* -X145103000Y-90282600D01* -X138730000Y-76000000D02* -X143730000Y-76000000D01* -X145156700Y-83964000D02* -X145103000Y-84017700D01* -X132500000Y-69770000D02* -X138730000Y-76000000D01* -X145103000Y-90282600D02* -X142999700Y-92385900D01* -%TO.N,/MCU_Core/BTN_STICK*% -D20* -X131997100Y-84250000D02* -X131750000Y-84250000D01* -X134709100Y-86962000D02* -X131997100Y-84250000D01* -X134709100Y-92787200D02* -X134709100Y-86962000D01* -%TO.N,/MCU_Core/PWR_BTN_SENSE*% -X144008300Y-99489600D02* -X145452900Y-98045000D01* -X129562500Y-102648600D02* -X130999800Y-102648600D01* -X130999800Y-102648600D02* -X134158800Y-99489600D01* -X128330100Y-101416200D02* -X129562500Y-102648600D01* -X125034700Y-101416200D02* -X128330100Y-101416200D01* -X120688600Y-97070100D02* -X125034700Y-101416200D01* -X134158800Y-99489600D02* -X144008300Y-99489600D01* -%TO.N,/Power_Buck/PWR_EN*% -X145850800Y-107623700D02* -X144474600Y-107623700D01* -X144474600Y-107623700D02* -X141116700Y-110981600D01* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X129861700Y-101982200D02* -X127525700Y-99646200D01* -X127525700Y-99646200D02* -X127525700Y-92504700D01* -%TO.N,ACCEL_INT1*% -X139636800Y-97508700D02* -X132056400Y-97508700D01* -X132056400Y-97508700D02* -X129871400Y-99693700D01* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X134103200Y-92072600D02* -X134103200Y-94424600D01* -X134103200Y-94424600D02* -X134775000Y-95096400D01* -X134105300Y-87305100D02* -X134153300Y-87353100D01* -X134153300Y-87353100D02* -X134153300Y-92022500D01* -X134153300Y-92022500D02* -X134103200Y-92072600D01* +X123750000Y-95250000D03* +X137000000Y-124900000D03* +X122300000Y-102800000D03* +%TO.N,/USB_C/USB_CC1*% +X129200000Y-123700000D03* +%TO.N,/USB_C/USB_CC2*% +X142300000Y-124900000D03* +%TO.N,VSYS*% +X129700000Y-93350000D03* +X142100000Y-79300000D03* +X144800000Y-90650000D03* +X144600000Y-86300000D03* +%TO.N,VBAT*% +X135900000Y-99000000D03* +X147300000Y-109300000D03* +%TO.N,/Power_Buck/BUCK_FB*% +X139885887Y-98225129D03* +X139500000Y-94850000D03* %TD*% %TA.AperFunction,Conductor*% %TO.N,3V3*% G36* -X148840836Y-97311739D02* +X149692539Y-60270185D02* G01* -X148934509Y-97350539D01* -X148985203Y-97371537D01* -X149121373Y-97398623D01* -X149139853Y-97402299D01* -X149139856Y-97402300D01* -X149139858Y-97402300D01* -X149297544Y-97402300D01* -X149297545Y-97402299D01* -X149452197Y-97371537D01* -X149578049Y-97319407D01* -X149647517Y-97311939D01* -X149709996Y-97343214D01* -X149745648Y-97403303D01* -X149749500Y-97433969D01* +X149738294Y-60322989D01* +X149749500Y-60374500D01* X149749500Y-129625500D01* X149729815Y-129692539D01* X149677011Y-129738294D01* @@ -558,146 +373,16 @@ X142320500Y-127801456D01* X142282052Y-127608170D01* X142282051Y-127608169D01* X142282051Y-127608165D01* -X142265490Y-127568182D01* -X142214264Y-127444510D01* -X142206795Y-127375041D01* -X142238070Y-127312562D01* -X142298160Y-127276910D01* -X142367985Y-127279404D01* -X142397714Y-127293954D01* -X142420821Y-127309394D01* -X142420823Y-127309395D01* -X142420827Y-127309397D01* -X142514749Y-127348300D01* -X142566503Y-127369737D01* -X142721153Y-127400499D01* -X142721156Y-127400500D01* -X142721158Y-127400500D01* -X142878844Y-127400500D01* -X142878845Y-127400499D01* -X143033497Y-127369737D01* -X143179179Y-127309394D01* -X143310289Y-127221789D01* -X143421789Y-127110289D01* -X143509394Y-126979179D01* -X143526472Y-126937950D01* -X143544795Y-126893713D01* -X145649500Y-126893713D01* -X145649500Y-127106287D01* -X145659534Y-127169644D01* -X145681669Y-127309397D01* -X145682754Y-127316243D01* -X145718446Y-127426092D01* -X145748444Y-127518414D01* -X145844951Y-127707820D01* -X145969890Y-127879786D01* -X146120213Y-128030109D01* -X146292179Y-128155048D01* -X146292181Y-128155049D01* -X146292184Y-128155051D01* -X146481588Y-128251557D01* -X146683757Y-128317246D01* -X146893713Y-128350500D01* -X146893714Y-128350500D01* -X147106286Y-128350500D01* -X147106287Y-128350500D01* -X147316243Y-128317246D01* -X147518412Y-128251557D01* -X147707816Y-128155051D01* -X147777639Y-128104322D01* -X147879786Y-128030109D01* -X147879788Y-128030106D01* -X147879792Y-128030104D01* -X148030104Y-127879792D01* -X148030106Y-127879788D01* -X148030109Y-127879786D01* -X148155048Y-127707820D01* -X148155047Y-127707820D01* -X148155051Y-127707816D01* -X148251557Y-127518412D01* -X148317246Y-127316243D01* -X148350500Y-127106287D01* -X148350500Y-126893713D01* -X148317246Y-126683757D01* -X148251557Y-126481588D01* -X148155051Y-126292184D01* -X148155049Y-126292181D01* -X148155048Y-126292179D01* -X148030109Y-126120213D01* -X147879786Y-125969890D01* -X147707820Y-125844951D01* -X147518414Y-125748444D01* -X147518413Y-125748443D01* -X147518412Y-125748443D01* -X147316243Y-125682754D01* -X147316241Y-125682753D01* -X147316240Y-125682753D01* -X147154957Y-125657208D01* -X147106287Y-125649500D01* -X146893713Y-125649500D01* -X146845042Y-125657208D01* -X146683760Y-125682753D01* -X146481585Y-125748444D01* -X146292179Y-125844951D01* -X146120213Y-125969890D01* -X145969890Y-126120213D01* -X145844951Y-126292179D01* -X145748444Y-126481585D01* -X145748443Y-126481587D01* -X145748443Y-126481588D01* -X145735587Y-126521155D01* -X145682753Y-126683760D01* -X145649500Y-126893713D01* -X143544795Y-126893713D01* -X143566468Y-126841389D01* -X143566468Y-126841388D01* -X143566469Y-126841386D01* -X143569737Y-126833497D01* -X143600500Y-126678842D01* -X143600500Y-126521158D01* -X143600500Y-126521155D01* -X143600499Y-126521153D01* -X143583838Y-126437392D01* -X143569737Y-126366503D01* -X143569735Y-126366498D01* -X143509397Y-126220827D01* -X143509390Y-126220814D01* -X143421789Y-126089711D01* -X143421786Y-126089707D01* -X143310292Y-125978213D01* -X143310288Y-125978210D01* -X143179185Y-125890609D01* -X143179172Y-125890602D01* -X143033501Y-125830264D01* -X143033489Y-125830261D01* -X142878845Y-125799500D01* -X142878842Y-125799500D01* -X142721158Y-125799500D01* -X142721155Y-125799500D01* -X142566510Y-125830261D01* -X142566498Y-125830264D01* -X142420827Y-125890602D01* -X142420814Y-125890609D01* -X142289711Y-125978210D01* -X142289707Y-125978213D01* -X142178213Y-126089707D01* -X142178210Y-126089711D01* -X142090609Y-126220814D01* -X142090602Y-126220827D01* -X142030264Y-126366498D01* -X142030261Y-126366510D01* -X141999500Y-126521153D01* -X141999500Y-126678846D01* -X142030261Y-126833489D01* -X142030264Y-126833501D01* -X142067295Y-126922902D01* -X142074764Y-126992371D01* -X142043489Y-127054850D01* -X141983399Y-127090502D01* -X141913574Y-127088008D01* -X141883843Y-127073456D01* +X142244875Y-127518414D01* +X142206635Y-127426092D01* +X142206628Y-127426079D01* +X142097139Y-127262218D01* +X142097136Y-127262214D01* +X141957785Y-127122863D01* +X141957781Y-127122860D01* X141793920Y-127013371D01* X141793907Y-127013364D01* +X141769855Y-127003402D01* X141611839Y-126937950D01* X141611829Y-126937947D01* X141418543Y-126899500D01* @@ -834,397 +519,144 @@ X120376713Y-127366785D01* X120309333Y-127348300D01* X120262643Y-127296321D01* X120250500Y-127242805D01* -X120250500Y-122393713D01* -X121649500Y-122393713D01* -X121649500Y-122606287D01* -X121682754Y-122816243D01* -X121739204Y-122989978D01* -X121748444Y-123018414D01* -X121844951Y-123207820D01* -X121969890Y-123379786D01* -X122120213Y-123530109D01* -X122292182Y-123655050D01* -X122329652Y-123674142D01* -X122380449Y-123722116D01* -X122397244Y-123789937D01* -X122374707Y-123856072D01* -X122320811Y-123899188D01* -X122220824Y-123940604D01* -X122220814Y-123940609D01* -X122089711Y-124028210D01* -X122089707Y-124028213D01* -X121978213Y-124139707D01* -X121978210Y-124139711D01* -X121890609Y-124270814D01* -X121890602Y-124270827D01* -X121830264Y-124416498D01* -X121830261Y-124416510D01* -X121799500Y-124571153D01* -X121799500Y-124728846D01* -X121830261Y-124883489D01* -X121830264Y-124883501D01* -X121890602Y-125029172D01* -X121890609Y-125029185D01* -X121958713Y-125131109D01* -X121979591Y-125197787D01* -X121961107Y-125265167D01* -X121958713Y-125268891D01* -X121890609Y-125370814D01* -X121890602Y-125370827D01* -X121830264Y-125516498D01* -X121830261Y-125516510D01* -X121799500Y-125671153D01* -X121799500Y-125828846D01* -X121830261Y-125983489D01* -X121830264Y-125983501D01* -X121890602Y-126129172D01* -X121890609Y-126129185D01* -X121978210Y-126260288D01* -X121978213Y-126260292D01* -X122089707Y-126371786D01* -X122089711Y-126371789D01* -X122220814Y-126459390D01* -X122220827Y-126459397D01* -X122366498Y-126519735D01* -X122366503Y-126519737D01* -X122521153Y-126550499D01* -X122521156Y-126550500D01* -X122521158Y-126550500D01* -X122678844Y-126550500D01* -X122678845Y-126550499D01* -X122833497Y-126519737D01* -X122979179Y-126459394D01* -X123110289Y-126371789D01* -X123221789Y-126260289D01* -X123309394Y-126129179D01* -X123369737Y-125983497D01* -X123400500Y-125828842D01* -X123400500Y-125671158D01* -X123400500Y-125671155D01* -X123400499Y-125671153D01* -X123387170Y-125604146D01* -X123369737Y-125516503D01* -X123340722Y-125446453D01* -X124969500Y-125446453D01* -X124969500Y-125604146D01* -X125000261Y-125758789D01* -X125000264Y-125758801D01* -X125060602Y-125904472D01* -X125060609Y-125904485D01* -X125148210Y-126035588D01* -X125148213Y-126035592D01* -X125259707Y-126147086D01* -X125259711Y-126147089D01* -X125390814Y-126234690D01* -X125390827Y-126234697D01* -X125529603Y-126292179D01* -X125536503Y-126295037D01* -X125691153Y-126325799D01* -X125691156Y-126325800D01* -X125691158Y-126325800D01* -X125848844Y-126325800D01* -X125848845Y-126325799D01* -X126003497Y-126295037D01* -X126149179Y-126234694D01* -X126169445Y-126221153D01* -X129599500Y-126221153D01* -X129599500Y-126378846D01* -X129630261Y-126533489D01* -X129630264Y-126533501D01* -X129690602Y-126679172D01* -X129690609Y-126679185D01* -X129778210Y-126810288D01* -X129778213Y-126810292D01* -X129889707Y-126921786D01* -X129889711Y-126921789D01* -X130020814Y-127009390D01* -X130020827Y-127009397D01* -X130130562Y-127054850D01* -X130166503Y-127069737D01* -X130321153Y-127100499D01* -X130321156Y-127100500D01* -X130321158Y-127100500D01* -X130478844Y-127100500D01* -X130478845Y-127100499D01* -X130633497Y-127069737D01* -X130769585Y-127013368D01* -X130779172Y-127009397D01* -X130779172Y-127009396D01* -X130779179Y-127009394D01* -X130910289Y-126921789D01* -X131021789Y-126810289D01* -X131109394Y-126679179D01* -X131169737Y-126533497D01* -X131200500Y-126378842D01* -X131200500Y-126221158D01* -X131200500Y-126221155D01* -X131200499Y-126221153D01* -X131192148Y-126179172D01* -X131169737Y-126066503D01* -X131169735Y-126066498D01* -X131109397Y-125920827D01* -X131109390Y-125920814D01* -X131021790Y-125789712D01* -X131021784Y-125789705D01* -X130953232Y-125721153D01* -X136599500Y-125721153D01* -X136599500Y-125878846D01* -X136630261Y-126033489D01* -X136630264Y-126033501D01* -X136690602Y-126179172D01* -X136690609Y-126179185D01* -X136778210Y-126310288D01* -X136778213Y-126310292D01* -X136889707Y-126421786D01* -X136889711Y-126421789D01* -X137020814Y-126509390D01* -X137020827Y-126509397D01* -X137120060Y-126550500D01* -X137166503Y-126569737D01* -X137321153Y-126600499D01* -X137321156Y-126600500D01* -X137321158Y-126600500D01* -X137478844Y-126600500D01* -X137478845Y-126600499D01* -X137633497Y-126569737D01* -X137779179Y-126509394D01* -X137886937Y-126437391D01* -X137953614Y-126416514D01* -X138020994Y-126434998D01* -X138058930Y-126471603D01* -X138128210Y-126575289D01* -X138239707Y-126686786D01* -X138239711Y-126686789D01* -X138370814Y-126774390D01* -X138370827Y-126774397D01* -X138513490Y-126833489D01* -X138516503Y-126834737D01* -X138671153Y-126865499D01* -X138671156Y-126865500D01* -X138671158Y-126865500D01* -X138828844Y-126865500D01* -X138828845Y-126865499D01* -X138983497Y-126834737D01* -X139129179Y-126774394D01* -X139260289Y-126686789D01* -X139371789Y-126575289D01* -X139459394Y-126444179D01* -X139519737Y-126298497D01* -X139550500Y-126143842D01* -X139550500Y-125986158D01* -X139550500Y-125986155D01* -X139550499Y-125986153D01* -X139537505Y-125920827D01* -X139519737Y-125831503D01* -X139519223Y-125830261D01* -X139459397Y-125685827D01* -X139459390Y-125685814D01* -X139371789Y-125554711D01* -X139371786Y-125554707D01* -X139260292Y-125443213D01* -X139260288Y-125443210D01* -X139129185Y-125355609D01* -X139129172Y-125355602D01* -X138983501Y-125295264D01* -X138983489Y-125295261D01* -X138828845Y-125264500D01* -X138828842Y-125264500D01* -X138671158Y-125264500D01* -X138671155Y-125264500D01* -X138516510Y-125295261D01* -X138516498Y-125295264D01* -X138370827Y-125355602D01* -X138370809Y-125355612D01* -X138263061Y-125427607D01* -X138196384Y-125448485D01* -X138129004Y-125430000D01* -X138091069Y-125393395D01* -X138021792Y-125289715D01* -X138021786Y-125289707D01* -X137910292Y-125178213D01* -X137910288Y-125178210D01* -X137779185Y-125090609D01* -X137779172Y-125090602D01* -X137633501Y-125030264D01* -X137633489Y-125030261D01* -X137478845Y-124999500D01* -X137478842Y-124999500D01* -X137321158Y-124999500D01* -X137321155Y-124999500D01* -X137166510Y-125030261D01* -X137166498Y-125030264D01* -X137020827Y-125090602D01* -X137020814Y-125090609D01* -X136889711Y-125178210D01* -X136889707Y-125178213D01* -X136778213Y-125289707D01* -X136778210Y-125289711D01* -X136690609Y-125420814D01* -X136690602Y-125420827D01* -X136630264Y-125566498D01* -X136630261Y-125566510D01* -X136599500Y-125721153D01* -X130953232Y-125721153D01* -X130910292Y-125678213D01* -X130910288Y-125678210D01* -X130779185Y-125590609D01* -X130779172Y-125590602D01* -X130633501Y-125530264D01* -X130633489Y-125530261D01* -X130478845Y-125499500D01* -X130478842Y-125499500D01* -X130321158Y-125499500D01* -X130321155Y-125499500D01* -X130166510Y-125530261D01* -X130166498Y-125530264D01* -X130020827Y-125590602D01* -X130020814Y-125590609D01* -X129889711Y-125678210D01* -X129889707Y-125678213D01* -X129778213Y-125789707D01* -X129778210Y-125789711D01* -X129690609Y-125920814D01* -X129690602Y-125920827D01* -X129630264Y-126066498D01* -X129630261Y-126066510D01* -X129599500Y-126221153D01* -X126169445Y-126221153D01* -X126280289Y-126147089D01* -X126283536Y-126143842D01* -X126299994Y-126127385D01* -X126391786Y-126035592D01* -X126391789Y-126035589D01* -X126479394Y-125904479D01* -X126479395Y-125904476D01* -X126479397Y-125904473D01* -X126526934Y-125789707D01* -X126539192Y-125760110D01* -X126566069Y-125719886D01* -X127782320Y-124503636D01* -X127843639Y-124470154D01* -X127913331Y-124475138D01* -X127969264Y-124517010D01* -X127984558Y-124543867D01* -X128040604Y-124679176D01* -X128040609Y-124679185D01* -X128128210Y-124810288D01* -X128128213Y-124810292D01* -X128239707Y-124921786D01* -X128239711Y-124921789D01* -X128370814Y-125009390D01* -X128370827Y-125009397D01* -X128516498Y-125069735D01* -X128516503Y-125069737D01* -X128671153Y-125100499D01* -X128671156Y-125100500D01* -X128671158Y-125100500D01* -X128828844Y-125100500D01* -X128828845Y-125100499D01* -X128983497Y-125069737D01* -X129129179Y-125009394D01* -X129260289Y-124921789D01* -X129371789Y-124810289D01* -X129459394Y-124679179D01* -X129519737Y-124533497D01* -X129550500Y-124378842D01* -X129550500Y-124221158D01* -X129550500Y-124221155D01* -X129550499Y-124221153D01* -X129529684Y-124116510D01* -X129519737Y-124066503D01* -X129492776Y-124001414D01* -X129485308Y-123931948D01* -X129516583Y-123869469D01* -X129559886Y-123839403D01* -X129595873Y-123824497D01* -X129595876Y-123824495D01* -X129595879Y-123824494D01* -X129726989Y-123736889D01* -X129838489Y-123625389D01* -X129926094Y-123494279D01* -X129986437Y-123348597D01* -X130017200Y-123193942D01* -X130017200Y-123036258D01* -X130017200Y-123036255D01* -X130017199Y-123036253D01* -X130008090Y-122990458D01* -X129986437Y-122881603D01* -X129930606Y-122746814D01* -X129926097Y-122735927D01* -X129926090Y-122735914D01* -X129835105Y-122599746D01* -X129836205Y-122599010D01* -X129811549Y-122540953D01* -X129823342Y-122472086D01* -X129847029Y-122438926D01* -X130100839Y-122185116D01* -X130162161Y-122151634D01* -X130188519Y-122148800D01* -X132281813Y-122148800D01* -X132348852Y-122168485D01* -X132394607Y-122221289D01* -X132403430Y-122248609D01* -X132430074Y-122382557D01* -X132423847Y-122452148D01* -X132380984Y-122507326D01* -X132355910Y-122521309D01* -X132206088Y-122583366D01* -X132206079Y-122583371D01* -X132042218Y-122692860D01* -X132042214Y-122692863D01* -X131902863Y-122832214D01* -X131902860Y-122832218D01* -X131793371Y-122996079D01* -X131793364Y-122996092D01* -X131717950Y-123178160D01* -X131717947Y-123178170D01* -X131679500Y-123371456D01* -X131679500Y-123456022D01* -X131659815Y-123523061D01* -X131607011Y-123568816D01* -X131579693Y-123577639D01* -X131566507Y-123580261D01* -X131566498Y-123580264D01* -X131420827Y-123640602D01* -X131420814Y-123640609D01* -X131289711Y-123728210D01* -X131289707Y-123728213D01* -X131178213Y-123839707D01* -X131178210Y-123839711D01* -X131090609Y-123970814D01* -X131090602Y-123970827D01* -X131030264Y-124116498D01* -X131030261Y-124116510D01* -X130999500Y-124271153D01* -X130999500Y-124428846D01* -X131030261Y-124583489D01* -X131030264Y-124583501D01* -X131090602Y-124729172D01* -X131090609Y-124729185D01* -X131178210Y-124860288D01* -X131178213Y-124860292D01* -X131289707Y-124971786D01* -X131289711Y-124971789D01* -X131420814Y-125059390D01* -X131420827Y-125059397D01* -X131520060Y-125100500D01* -X131566503Y-125119737D01* -X131699174Y-125146127D01* -X131721153Y-125150499D01* -X131721156Y-125150500D01* -X131721158Y-125150500D01* -X131798307Y-125150500D01* -X131865346Y-125170185D01* -X131898904Y-125203149D01* -X131898997Y-125203074D01* -X131899702Y-125203933D01* -X131901411Y-125205612D01* -X131902861Y-125207783D01* +X120250500Y-126893713D01* +X145649500Y-126893713D01* +X145649500Y-127106287D01* +X145659534Y-127169644D01* +X145679598Y-127296321D01* +X145682754Y-127316243D01* +X145718446Y-127426092D01* +X145748444Y-127518414D01* +X145844951Y-127707820D01* +X145969890Y-127879786D01* +X146120213Y-128030109D01* +X146292179Y-128155048D01* +X146292181Y-128155049D01* +X146292184Y-128155051D01* +X146481588Y-128251557D01* +X146683757Y-128317246D01* +X146893713Y-128350500D01* +X146893714Y-128350500D01* +X147106286Y-128350500D01* +X147106287Y-128350500D01* +X147316243Y-128317246D01* +X147518412Y-128251557D01* +X147707816Y-128155051D01* +X147777639Y-128104322D01* +X147879786Y-128030109D01* +X147879788Y-128030106D01* +X147879792Y-128030104D01* +X148030104Y-127879792D01* +X148030106Y-127879788D01* +X148030109Y-127879786D01* +X148155048Y-127707820D01* +X148155047Y-127707820D01* +X148155051Y-127707816D01* +X148251557Y-127518412D01* +X148317246Y-127316243D01* +X148350500Y-127106287D01* +X148350500Y-126893713D01* +X148317246Y-126683757D01* +X148251557Y-126481588D01* +X148155051Y-126292184D01* +X148155049Y-126292181D01* +X148155048Y-126292179D01* +X148030109Y-126120213D01* +X147879786Y-125969890D01* +X147707820Y-125844951D01* +X147518414Y-125748444D01* +X147518413Y-125748443D01* +X147518412Y-125748443D01* +X147316243Y-125682754D01* +X147316241Y-125682753D01* +X147316240Y-125682753D01* +X147154957Y-125657208D01* +X147106287Y-125649500D01* +X146893713Y-125649500D01* +X146845042Y-125657208D01* +X146683760Y-125682753D01* +X146481585Y-125748444D01* +X146292179Y-125844951D01* +X146120213Y-125969890D01* +X145969890Y-126120213D01* +X145844951Y-126292179D01* +X145748444Y-126481585D01* +X145682753Y-126683760D01* +X145649500Y-126893713D01* +X120250500Y-126893713D01* +X120250500Y-126663399D01* +X120270185Y-126596360D01* +X120322989Y-126550605D01* +X120392147Y-126540661D01* +X120398692Y-126541782D01* +X120521155Y-126566142D01* +X120521158Y-126566142D01* +X120678844Y-126566142D01* +X120678845Y-126566141D01* +X120833497Y-126535379D01* +X120979179Y-126475036D01* +X121110289Y-126387431D01* +X121221789Y-126275931D01* +X121309394Y-126144821D01* +X121369737Y-125999139D01* +X121400500Y-125844484D01* +X121400500Y-125705047D01* +X121420185Y-125638008D01* +X121472989Y-125592253D01* +X121476986Y-125590512D01* +X121479179Y-125589604D01* +X121600848Y-125508306D01* +X121667525Y-125487429D01* +X121734906Y-125505913D01* +X121781596Y-125557892D01* +X121784299Y-125563953D01* +X121790603Y-125579172D01* +X121790606Y-125579178D01* +X121790609Y-125579185D01* +X121878210Y-125710288D01* +X121878213Y-125710292D01* +X121989707Y-125821786D01* +X121989711Y-125821789D01* +X122120814Y-125909390D01* +X122120827Y-125909397D01* +X122266498Y-125969735D01* +X122266503Y-125969737D01* +X122414276Y-125999131D01* +X122421153Y-126000499D01* +X122421156Y-126000500D01* +X122421158Y-126000500D01* +X122578844Y-126000500D01* +X122578845Y-126000499D01* +X122733497Y-125969737D01* +X122879179Y-125909394D01* +X123010289Y-125821789D01* +X123121789Y-125710289D01* +X123209394Y-125579179D01* +X123269737Y-125433497D01* +X123300500Y-125278842D01* +X123300500Y-125121158D01* +X123300500Y-125121155D01* +X123300499Y-125121153D01* +X123284255Y-125039488D01* +X123269737Y-124966503D01* +X123266651Y-124959052D01* +X123209397Y-124820827D01* +X123209390Y-124820814D01* +X123121789Y-124689711D01* +X123121786Y-124689707D01* +X123100622Y-124668543D01* +X131679499Y-124668543D01* +X131717947Y-124861829D01* +X131717950Y-124861839D01* +X131793364Y-125043907D01* +X131793371Y-125043920D01* +X131902860Y-125207781D01* +X131902863Y-125207785D01* X132042214Y-125347136D01* X132042218Y-125347139D01* X132206079Y-125456628D01* X132206092Y-125456635D01* -X132383848Y-125530263D01* +X132363383Y-125521786D01* X132388165Y-125532051D01* X132388169Y-125532051D01* X132388170Y-125532052D01* @@ -1254,102 +686,47 @@ X134185766Y-125125500D01* X134332135Y-125086281D01* X134463365Y-125010515D01* X134570515Y-124903365D01* -X134646281Y-124772135D01* -X134685500Y-124625766D01* -X134685500Y-124474234D01* -X134646281Y-124327865D01* -X134570515Y-124196635D01* -X134463365Y-124089485D01* -X134385162Y-124044334D01* -X134332136Y-124013719D01* -X134224994Y-123985011D01* -X134185766Y-123974500D01* -X134034234Y-123974500D01* -X133887862Y-124013719D01* -X133866499Y-124026054D01* -X133798598Y-124042525D01* -X133732572Y-124019673D01* -X133689382Y-123964751D01* -X133680500Y-123918666D01* -X133680500Y-123371456D01* -X133642052Y-123178170D01* -X133642051Y-123178169D01* -X133642051Y-123178165D01* -X133583272Y-123036258D01* -X133564301Y-122990457D01* -X133566760Y-122989438D01* -X133554825Y-122932368D01* -X133579766Y-122867101D01* -X133609540Y-122839106D01* -X133710288Y-122771789D01* -X133821788Y-122660289D01* -X133909393Y-122529179D01* -X133967970Y-122387760D01* -X134011808Y-122333360D01* -X134078102Y-122311294D01* -X134145801Y-122328572D01* -X134151420Y-122332113D01* -X134270814Y-122411890D01* -X134270827Y-122411897D01* -X134415185Y-122471691D01* -X134455414Y-122498571D01* -X134703653Y-122746811D01* -X134703654Y-122746812D01* -X134818392Y-122823477D01* -X134945867Y-122876278D01* -X134945872Y-122876280D01* -X134945876Y-122876280D01* -X134945877Y-122876281D01* -X135081203Y-122903200D01* -X135081206Y-122903200D01* -X139185196Y-122903200D01* -X139276240Y-122885089D01* -X139320528Y-122876280D01* -X139410282Y-122839103D01* -X139448007Y-122823477D01* -X139448008Y-122823476D01* -X139448011Y-122823475D01* -X139562743Y-122746814D01* -X139644587Y-122664968D01* -X139684804Y-122638095D01* -X139829179Y-122578294D01* -X139929499Y-122511261D01* -X139996176Y-122490384D01* -X140063556Y-122508868D01* -X140101492Y-122545473D01* -X140178210Y-122660288D01* -X140178213Y-122660292D01* -X140289708Y-122771787D01* -X140289711Y-122771789D01* -X140390457Y-122839105D01* -X140435261Y-122892715D01* -X140443968Y-122962040D01* -X140434540Y-122989978D01* -X140435699Y-122990458D01* -X140357950Y-123178160D01* -X140357947Y-123178170D01* -X140319500Y-123371456D01* -X140319500Y-123918666D01* -X140299815Y-123985705D01* -X140247011Y-124031460D01* -X140177853Y-124041404D01* -X140133501Y-124026054D01* -X140112137Y-124013719D01* -X140004994Y-123985011D01* -X139965766Y-123974500D01* -X139814234Y-123974500D01* -X139667863Y-124013719D01* -X139536635Y-124089485D01* -X139536632Y-124089487D01* -X139429487Y-124196632D01* -X139429485Y-124196635D01* -X139353719Y-124327863D01* -X139316975Y-124464998D01* +X134617980Y-124821153D01* +X136199500Y-124821153D01* +X136199500Y-124978846D01* +X136230261Y-125133489D01* +X136230264Y-125133501D01* +X136290602Y-125279172D01* +X136290609Y-125279185D01* +X136378210Y-125410288D01* +X136378213Y-125410292D01* +X136489707Y-125521786D01* +X136489711Y-125521789D01* +X136620814Y-125609390D01* +X136620827Y-125609397D01* +X136717646Y-125649500D01* +X136766503Y-125669737D01* +X136921153Y-125700499D01* +X136921156Y-125700500D01* +X136921158Y-125700500D01* +X137078844Y-125700500D01* +X137078845Y-125700499D01* +X137233497Y-125669737D01* +X137379179Y-125609394D01* +X137510289Y-125521789D01* +X137621789Y-125410289D01* +X137709394Y-125279179D01* +X137769737Y-125133497D01* +X137800500Y-124978842D01* +X137800500Y-124821158D01* +X137800500Y-124821155D01* +X137800499Y-124821153D01* +X137774353Y-124689711D01* +X137769737Y-124666503D01* +X137761540Y-124646713D01* +X137709397Y-124520827D01* +X137709390Y-124520814D01* +X137678266Y-124474234D01* X139314500Y-124474234D01* X139314500Y-124625766D01* X139325962Y-124668543D01* X139353719Y-124772136D01* -X139375747Y-124810289D01* +X139391602Y-124837750D01* X139429485Y-124903365D01* X139536635Y-125010515D01* X139667865Y-125086281D01* @@ -1374,7 +751,7 @@ X140682214Y-125347136D01* X140682218Y-125347139D01* X140846079Y-125456628D01* X140846092Y-125456635D01* -X141023848Y-125530263D01* +X141003383Y-125521786D01* X141028165Y-125532051D01* X141028169Y-125532051D01* X141028170Y-125532052D01* @@ -1383,18 +760,50 @@ X141221459Y-125570500D01* X141418543Y-125570500D01* X141548582Y-125544632D01* X141611835Y-125532051D01* -X141793914Y-125456632D01* -X141957782Y-125347139D01* -X142097139Y-125207782D01* -X142206632Y-125043914D01* -X142282051Y-124861835D01* -X142294632Y-124798582D01* -X142320500Y-124668543D01* +X141669886Y-125508004D01* +X141739353Y-125500535D01* +X141786230Y-125519463D01* +X141920814Y-125609390D01* +X141920827Y-125609397D01* +X142017646Y-125649500D01* +X142066503Y-125669737D01* +X142221153Y-125700499D01* +X142221156Y-125700500D01* +X142221158Y-125700500D01* +X142378844Y-125700500D01* +X142378845Y-125700499D01* +X142533497Y-125669737D01* +X142679179Y-125609394D01* +X142810289Y-125521789D01* +X142921789Y-125410289D01* +X143009394Y-125279179D01* +X143069737Y-125133497D01* +X143100500Y-124978842D01* +X143100500Y-124821158D01* +X143100500Y-124821155D01* +X143100499Y-124821153D01* +X143074353Y-124689711D01* +X143069737Y-124666503D01* +X143061540Y-124646713D01* +X143009397Y-124520827D01* +X143009390Y-124520814D01* +X142921789Y-124389711D01* +X142921786Y-124389707D01* +X142810292Y-124278213D01* +X142810288Y-124278210D01* +X142679185Y-124190609D01* +X142679172Y-124190602D01* +X142533501Y-124130264D01* +X142533491Y-124130261D01* +X142420308Y-124107747D01* +X142358397Y-124075362D01* +X142323823Y-124014646D01* +X142320500Y-123986130D01* X142320500Y-123371456D01* X142282052Y-123178170D01* X142282051Y-123178169D01* X142282051Y-123178165D01* -X142223272Y-123036258D01* +X142252511Y-123106849D01* X142206635Y-122996092D01* X142206628Y-122996079D01* X142097139Y-122832218D01* @@ -1402,11 +811,378 @@ X142097136Y-122832214D01* X141957785Y-122692863D01* X141957781Y-122692860D01* X141793920Y-122583371D01* -X141793911Y-122583366D01* +X141793907Y-122583364D01* X141680511Y-122536395D01* -X141644088Y-122521308D01* -X141589685Y-122477467D01* -X141572216Y-122424983D01* +X141611839Y-122507950D01* +X141611829Y-122507947D01* +X141418543Y-122469500D01* +X141418541Y-122469500D01* +X141221459Y-122469500D01* +X141221457Y-122469500D01* +X141028170Y-122507947D01* +X141028160Y-122507950D01* +X140846092Y-122583364D01* +X140846079Y-122583371D01* +X140682218Y-122692860D01* +X140682214Y-122692863D01* +X140542863Y-122832214D01* +X140542860Y-122832218D01* +X140433371Y-122996079D01* +X140433364Y-122996092D01* +X140357950Y-123178160D01* +X140357947Y-123178170D01* +X140319500Y-123371456D01* +X140319500Y-123918666D01* +X140299815Y-123985705D01* +X140247011Y-124031460D01* +X140177853Y-124041404D01* +X140133501Y-124026054D01* +X140112137Y-124013719D01* +X140007584Y-123985705D01* +X139965766Y-123974500D01* +X139814234Y-123974500D01* +X139667863Y-124013719D01* +X139536635Y-124089485D01* +X139536632Y-124089487D01* +X139429487Y-124196632D01* +X139429485Y-124196635D01* +X139353719Y-124327863D01* +X139316975Y-124464998D01* +X139314500Y-124474234D01* +X137678266Y-124474234D01* +X137621789Y-124389711D01* +X137621786Y-124389707D01* +X137510292Y-124278213D01* +X137510288Y-124278210D01* +X137379185Y-124190609D01* +X137379172Y-124190602D01* +X137233501Y-124130264D01* +X137233489Y-124130261D01* +X137078845Y-124099500D01* +X137078842Y-124099500D01* +X136921158Y-124099500D01* +X136921155Y-124099500D01* +X136766510Y-124130261D01* +X136766498Y-124130264D01* +X136620827Y-124190602D01* +X136620814Y-124190609D01* +X136489711Y-124278210D01* +X136489707Y-124278213D01* +X136378213Y-124389707D01* +X136378210Y-124389711D01* +X136290609Y-124520814D01* +X136290602Y-124520827D01* +X136230264Y-124666498D01* +X136230261Y-124666510D01* +X136199500Y-124821153D01* +X134617980Y-124821153D01* +X134646281Y-124772135D01* +X134685500Y-124625766D01* +X134685500Y-124474234D01* +X134646281Y-124327865D01* +X134570515Y-124196635D01* +X134463365Y-124089485D01* +X134385162Y-124044334D01* +X134332136Y-124013719D01* +X134227584Y-123985705D01* +X134185766Y-123974500D01* +X134034234Y-123974500D01* +X133887862Y-124013719D01* +X133866499Y-124026054D01* +X133798598Y-124042525D01* +X133732572Y-124019673D01* +X133689382Y-123964751D01* +X133680500Y-123918666D01* +X133680500Y-123371456D01* +X133642052Y-123178170D01* +X133642051Y-123178169D01* +X133642051Y-123178165D01* +X133612511Y-123106849D01* +X133566635Y-122996092D01* +X133566628Y-122996079D01* +X133457139Y-122832218D01* +X133457136Y-122832214D01* +X133317785Y-122692863D01* +X133317781Y-122692860D01* +X133153920Y-122583371D01* +X133153907Y-122583364D01* +X132971839Y-122507950D01* +X132971829Y-122507947D01* +X132778543Y-122469500D01* +X132778541Y-122469500D01* +X132581459Y-122469500D01* +X132581457Y-122469500D01* +X132388170Y-122507947D01* +X132388160Y-122507950D01* +X132206092Y-122583364D01* +X132206079Y-122583371D01* +X132042218Y-122692860D01* +X132042214Y-122692863D01* +X131902863Y-122832214D01* +X131902860Y-122832218D01* +X131793371Y-122996079D01* +X131793364Y-122996092D01* +X131717950Y-123178160D01* +X131717947Y-123178170D01* +X131679500Y-123371456D01* +X131679500Y-123371459D01* +X131679500Y-124668541D01* +X131679500Y-124668543D01* +X131679499Y-124668543D01* +X123100622Y-124668543D01* +X123010292Y-124578213D01* +X123010288Y-124578210D01* +X122879185Y-124490609D01* +X122879172Y-124490602D01* +X122733499Y-124430263D01* +X122733493Y-124430261D01* +X122693816Y-124422369D01* +X122631906Y-124389983D01* +X122603448Y-124348204D01* +X122584138Y-124301585D01* +X122584131Y-124301572D01* +X122496530Y-124170469D01* +X122496527Y-124170465D01* +X122385033Y-124058971D01* +X122385029Y-124058968D01* +X122253926Y-123971367D01* +X122253913Y-123971360D01* +X122108242Y-123911022D01* +X122108230Y-123911019D01* +X121953586Y-123880258D01* +X121953583Y-123880258D01* +X121795899Y-123880258D01* +X121795896Y-123880258D01* +X121641251Y-123911019D01* +X121641239Y-123911022D01* +X121495568Y-123971360D01* +X121495555Y-123971367D01* +X121364455Y-124058966D01* +X121364446Y-124058973D01* +X121363216Y-124060204D01* +X121362414Y-124060641D01* +X121359748Y-124062830D01* +X121359332Y-124062324D01* +X121301890Y-124093684D01* +X121251353Y-124094133D01* +X121226188Y-124089127D01* +X121178842Y-124079710D01* +X121021158Y-124079710D01* +X121021155Y-124079710D01* +X120866510Y-124110471D01* +X120866498Y-124110474D01* +X120720827Y-124170812D01* +X120720814Y-124170819D01* +X120589711Y-124258420D01* +X120589707Y-124258423D01* +X120478213Y-124369917D01* +X120478206Y-124369926D01* +X120477597Y-124370838D01* +X120477155Y-124371207D01* +X120474347Y-124374629D01* +X120473697Y-124374096D01* +X120423982Y-124415639D01* +X120354656Y-124424342D01* +X120291631Y-124394183D01* +X120254916Y-124334737D01* +X120250500Y-124301940D01* +X120250500Y-122393713D01* +X121649500Y-122393713D01* +X121649500Y-122606287D01* +X121653406Y-122630948D01* +X121671906Y-122747756D01* +X121682754Y-122816243D01* +X121739409Y-122990609D01* +X121748444Y-123018414D01* +X121844951Y-123207820D01* +X121969890Y-123379786D01* +X122120213Y-123530109D01* +X122292179Y-123655048D01* +X122292181Y-123655049D01* +X122292184Y-123655051D01* +X122481588Y-123751557D01* +X122683757Y-123817246D01* +X122893713Y-123850500D01* +X122893714Y-123850500D01* +X123106286Y-123850500D01* +X123106287Y-123850500D01* +X123316243Y-123817246D01* +X123518412Y-123751557D01* +X123707816Y-123655051D01* +X123754473Y-123621153D01* +X123879786Y-123530109D01* +X123879788Y-123530106D01* +X123879792Y-123530104D01* +X124030104Y-123379792D01* +X124030106Y-123379788D01* +X124030109Y-123379786D01* +X124116053Y-123261492D01* +X125201698Y-123261492D01* +X125201698Y-123419185D01* +X125232459Y-123573828D01* +X125232462Y-123573840D01* +X125292800Y-123719511D01* +X125292807Y-123719524D01* +X125380408Y-123850627D01* +X125380411Y-123850631D01* +X125491905Y-123962125D01* +X125491909Y-123962128D01* +X125623012Y-124049729D01* +X125623025Y-124049736D01* +X125743168Y-124099500D01* +X125768701Y-124110076D01* +X125923351Y-124140838D01* +X125923354Y-124140839D01* +X125923356Y-124140839D01* +X126081042Y-124140839D01* +X126081043Y-124140838D01* +X126235695Y-124110076D01* +X126259899Y-124100049D01* +X126329368Y-124092581D01* +X126386016Y-124118757D01* +X126389711Y-124121789D01* +X126520814Y-124209390D01* +X126520827Y-124209397D01* +X126639188Y-124258423D01* +X126666503Y-124269737D01* +X126821153Y-124300499D01* +X126821156Y-124300500D01* +X126821158Y-124300500D01* +X126978844Y-124300500D01* +X126978845Y-124300499D01* +X127133497Y-124269737D01* +X127279179Y-124209394D01* +X127410289Y-124121789D01* +X127521789Y-124010289D01* +X127609394Y-123879179D01* +X127609967Y-123877797D01* +X127650954Y-123778844D01* +X127669737Y-123733497D01* +X127692083Y-123621158D01* +X127692084Y-123621153D01* +X128399500Y-123621153D01* +X128399500Y-123778846D01* +X128430261Y-123933489D01* +X128430264Y-123933501D01* +X128490602Y-124079172D01* +X128490609Y-124079185D01* +X128578210Y-124210288D01* +X128578213Y-124210292D01* +X128689707Y-124321786D01* +X128689711Y-124321789D01* +X128820814Y-124409390D01* +X128820827Y-124409397D01* +X128914995Y-124448402D01* +X128966503Y-124469737D01* +X129121153Y-124500499D01* +X129121156Y-124500500D01* +X129121158Y-124500500D01* +X129278844Y-124500500D01* +X129278845Y-124500499D01* +X129433497Y-124469737D01* +X129578170Y-124409812D01* +X129579172Y-124409397D01* +X129579172Y-124409396D01* +X129579179Y-124409394D01* +X129710289Y-124321789D01* +X129821789Y-124210289D01* +X129909394Y-124079179D01* +X129921593Y-124049729D01* +X129956791Y-123964751D01* +X129969737Y-123933497D01* +X130000500Y-123778842D01* +X130000500Y-123621158D01* +X130000500Y-123621155D01* +X130000499Y-123621153D01* +X129969738Y-123466510D01* +X129969737Y-123466503D01* +X129950955Y-123421158D01* +X129947501Y-123412819D01* +X129909397Y-123320827D01* +X129909390Y-123320814D01* +X129821789Y-123189711D01* +X129821786Y-123189707D01* +X129710292Y-123078213D01* +X129710288Y-123078210D01* +X129579185Y-122990609D01* +X129579172Y-122990602D01* +X129433501Y-122930264D01* +X129433489Y-122930261D01* +X129278845Y-122899500D01* +X129278842Y-122899500D01* +X129121158Y-122899500D01* +X129121155Y-122899500D01* +X128966510Y-122930261D01* +X128966498Y-122930264D01* +X128820827Y-122990602D01* +X128820814Y-122990609D01* +X128689711Y-123078210D01* +X128689707Y-123078213D01* +X128578213Y-123189707D01* +X128578210Y-123189711D01* +X128490609Y-123320814D01* +X128490602Y-123320827D01* +X128430264Y-123466498D01* +X128430261Y-123466510D01* +X128399500Y-123621153D01* +X127692084Y-123621153D01* +X127698107Y-123590875D01* +X127698107Y-123590874D01* +X127700500Y-123578844D01* +X127700500Y-123421155D01* +X127700499Y-123421153D01* +X127692272Y-123379792D01* +X127669737Y-123266503D01* +X127669735Y-123266498D01* +X127609397Y-123120827D01* +X127609390Y-123120814D01* +X127521789Y-122989711D01* +X127521786Y-122989707D01* +X127410292Y-122878213D01* +X127410288Y-122878210D01* +X127279185Y-122790609D01* +X127279172Y-122790602D01* +X127133501Y-122730264D01* +X127133489Y-122730261D01* +X126978845Y-122699500D01* +X126978842Y-122699500D01* +X126821158Y-122699500D01* +X126821155Y-122699500D01* +X126666511Y-122730260D01* +X126666498Y-122730264D01* +X126642292Y-122740290D01* +X126572823Y-122747756D01* +X126516183Y-122721582D01* +X126512491Y-122718552D01* +X126381383Y-122630948D01* +X126381370Y-122630941D01* +X126235699Y-122570603D01* +X126235687Y-122570600D01* +X126081043Y-122539839D01* +X126081040Y-122539839D01* +X125923356Y-122539839D01* +X125923353Y-122539839D01* +X125768708Y-122570600D01* +X125768696Y-122570603D01* +X125623025Y-122630941D01* +X125623012Y-122630948D01* +X125491909Y-122718549D01* +X125491905Y-122718552D01* +X125380411Y-122830046D01* +X125380408Y-122830050D01* +X125292807Y-122961153D01* +X125292800Y-122961166D01* +X125232462Y-123106837D01* +X125232459Y-123106849D01* +X125201698Y-123261492D01* +X124116053Y-123261492D01* +X124155050Y-123207817D01* +X124159488Y-123199109D01* +X124206502Y-123106837D01* +X124251557Y-123018412D01* +X124317246Y-122816243D01* +X124350500Y-122606287D01* +X124350500Y-122424983D01* X144099500Y-122424983D01* X144099500Y-123775001D01* X144099501Y-123775018D01* @@ -1414,7 +1190,7 @@ X144110000Y-123877796D01* X144110001Y-123877799D01* X144165185Y-124044331D01* X144165187Y-124044336D01* -X144188870Y-124082732D01* +X144184324Y-124075362D01* X144257288Y-124193656D01* X144381344Y-124317712D01* X144530666Y-124409814D01* @@ -1423,7 +1199,7 @@ X144799991Y-124475500D01* X145600008Y-124475499D01* X145600016Y-124475498D01* X145600019Y-124475498D01* -X145656302Y-124469748D01* +X145656434Y-124469735D01* X145702797Y-124464999D01* X145869334Y-124409814D01* X146018656Y-124317712D01* @@ -1493,174 +1269,12 @@ X144381342Y-121882289D01* X144257289Y-122006342D01* X144165187Y-122155663D01* X144165185Y-122155668D01* -X144146257Y-122212789D01* +X144137349Y-122239670D01* X144110001Y-122322203D01* X144110001Y-122322204D01* X144110000Y-122322204D01* X144099500Y-122424983D01* -X141572216Y-122424983D01* -X141567620Y-122411173D01* -X141569924Y-122382555D01* -X141600500Y-122228844D01* -X141600500Y-122071155D01* -X141600499Y-122071153D01* -X141600378Y-122070543D01* -X141569737Y-121916503D01* -X141555565Y-121882288D01* -X141509397Y-121770827D01* -X141509390Y-121770814D01* -X141421789Y-121639711D01* -X141421786Y-121639707D01* -X141310292Y-121528213D01* -X141310288Y-121528210D01* -X141179185Y-121440609D01* -X141179172Y-121440602D01* -X141033501Y-121380264D01* -X141033489Y-121380261D01* -X140878845Y-121349500D01* -X140878842Y-121349500D01* -X140721158Y-121349500D01* -X140721155Y-121349500D01* -X140566510Y-121380261D01* -X140566498Y-121380264D01* -X140420827Y-121440602D01* -X140420816Y-121440608D01* -X140320499Y-121507638D01* -X140253822Y-121528515D01* -X140186442Y-121510030D01* -X140148507Y-121473426D01* -X140071789Y-121358611D01* -X140071786Y-121358607D01* -X139960292Y-121247113D01* -X139960288Y-121247110D01* -X139829185Y-121159509D01* -X139829172Y-121159502D01* -X139683501Y-121099164D01* -X139683489Y-121099161D01* -X139528845Y-121068400D01* -X139528842Y-121068400D01* -X139371158Y-121068400D01* -X139371155Y-121068400D01* -X139216510Y-121099161D01* -X139216498Y-121099164D01* -X139070827Y-121159502D01* -X139070814Y-121159509D01* -X138939711Y-121247110D01* -X138939707Y-121247113D01* -X138828213Y-121358607D01* -X138828210Y-121358611D01* -X138769090Y-121447091D01* -X138715478Y-121491896D01* -X138665988Y-121502200D01* -X136668206Y-121502200D01* -X136601167Y-121482515D01* -X136555412Y-121429711D01* -X136546589Y-121402392D01* -X136519738Y-121267408D01* -X136519737Y-121267407D01* -X136519737Y-121267403D01* -X136511332Y-121247111D01* -X136459397Y-121121727D01* -X136459390Y-121121714D01* -X136371789Y-120990611D01* -X136371786Y-120990607D01* -X136260292Y-120879113D01* -X136260288Y-120879110D01* -X136129185Y-120791509D01* -X136129172Y-120791502D01* -X135983501Y-120731164D01* -X135983489Y-120731161D01* -X135828845Y-120700400D01* -X135828842Y-120700400D01* -X135671158Y-120700400D01* -X135671155Y-120700400D01* -X135516510Y-120731161D01* -X135516498Y-120731164D01* -X135370827Y-120791502D01* -X135370814Y-120791509D01* -X135239711Y-120879110D01* -X135239707Y-120879113D01* -X135156027Y-120962794D01* -X135094704Y-120996279D01* -X135025012Y-120991295D01* -X135020894Y-120989674D01* -X134884815Y-120933309D01* -X134844582Y-120906425D01* -X134842343Y-120904186D01* -X134842342Y-120904185D01* -X134842341Y-120904184D01* -X134727607Y-120827522D01* -X134600132Y-120774721D01* -X134600122Y-120774718D01* -X134464796Y-120747800D01* -X134464794Y-120747800D01* -X134464793Y-120747800D01* -X129915994Y-120747800D01* -X129778006Y-120747800D01* -X129778004Y-120747800D01* -X129642677Y-120774718D01* -X129642667Y-120774721D01* -X129515192Y-120827522D01* -X129400454Y-120904187D01* -X125575412Y-124729229D01* -X125535184Y-124756109D01* -X125390823Y-124815904D01* -X125390814Y-124815909D01* -X125259711Y-124903510D01* -X125259707Y-124903513D01* -X125148213Y-125015007D01* -X125148210Y-125015011D01* -X125060609Y-125146114D01* -X125060602Y-125146127D01* -X125000264Y-125291798D01* -X125000261Y-125291810D01* -X124969500Y-125446453D01* -X123340722Y-125446453D01* -X123333907Y-125430000D01* -X123309397Y-125370827D01* -X123309393Y-125370820D01* -X123309389Y-125370814D01* -X123241284Y-125268888D01* -X123220408Y-125202214D01* -X123238892Y-125134834D01* -X123241257Y-125131152D01* -X123309394Y-125029179D01* -X123369737Y-124883497D01* -X123400500Y-124728842D01* -X123400500Y-124571158D01* -X123400500Y-124571155D01* -X123400499Y-124571153D01* -X123395071Y-124543867D01* -X123369737Y-124416503D01* -X123354138Y-124378844D01* -X123309397Y-124270827D01* -X123309390Y-124270814D01* -X123221789Y-124139711D01* -X123221786Y-124139707D01* -X123128413Y-124046334D01* -X123094928Y-123985011D01* -X123099912Y-123915319D01* -X123141784Y-123859386D01* -X123196695Y-123836180D01* -X123272524Y-123824170D01* -X123316238Y-123817247D01* -X123316238Y-123817246D01* -X123316243Y-123817246D01* -X123518412Y-123751557D01* -X123707816Y-123655051D01* -X123738584Y-123632697D01* -X123879786Y-123530109D01* -X123879788Y-123530106D01* -X123879792Y-123530104D01* -X124030104Y-123379792D01* -X124030106Y-123379788D01* -X124030109Y-123379786D01* -X124155048Y-123207820D01* -X124155047Y-123207820D01* -X124155051Y-123207816D01* -X124251557Y-123018412D01* -X124317246Y-122816243D01* -X124350500Y-122606287D01* +X124350500Y-122424983D01* X124350500Y-122393713D01* X124317246Y-122183757D01* X124251557Y-121981588D01* @@ -1681,8 +1295,6 @@ X123106287Y-121149500D01* X122893713Y-121149500D01* X122845042Y-121157208D01* X122683760Y-121182753D01* -X122683757Y-121182754D01* -X122485688Y-121247111D01* X122481585Y-121248444D01* X122292179Y-121344951D01* X122120213Y-121469890D01* @@ -1690,2403 +1302,6340 @@ X121969890Y-121620213D01* X121844951Y-121792179D01* X121748444Y-121981585D01* X121682753Y-122183760D01* -X121659059Y-122333360D01* +X121673550Y-122241866D01* X121649500Y-122393713D01* X120250500Y-122393713D01* -X120250500Y-119236153D01* -X120949500Y-119236153D01* -X120949500Y-119393846D01* -X120980261Y-119548489D01* -X120980264Y-119548501D01* -X121040602Y-119694172D01* -X121040609Y-119694185D01* -X121128210Y-119825288D01* -X121128213Y-119825292D01* -X121239707Y-119936786D01* -X121239711Y-119936789D01* -X121370814Y-120024390D01* -X121370827Y-120024397D01* -X121470060Y-120065500D01* -X121516503Y-120084737D01* -X121671153Y-120115499D01* -X121671156Y-120115500D01* -X121671158Y-120115500D01* -X121828844Y-120115500D01* -X121828845Y-120115499D01* -X121983497Y-120084737D01* -X122129179Y-120024394D01* -X122260289Y-119936789D01* -X122371789Y-119825289D01* -X122459394Y-119694179D01* -X122519737Y-119548497D01* -X122550500Y-119393842D01* -X122550500Y-119236158D01* -X122550500Y-119236155D01* -X122550499Y-119236153D01* -X122537517Y-119170889D01* -X122519737Y-119081503D01* -X122501497Y-119037468D01* -X122459397Y-118935827D01* -X122459390Y-118935814D01* -X122371789Y-118804711D01* -X122371786Y-118804707D01* -X122260292Y-118693213D01* -X122260288Y-118693210D01* -X122129185Y-118605609D01* -X122129172Y-118605602D01* -X121983501Y-118545264D01* -X121983489Y-118545261D01* -X121828845Y-118514500D01* -X121828842Y-118514500D01* -X121671158Y-118514500D01* -X121671155Y-118514500D01* -X121516510Y-118545261D01* -X121516498Y-118545264D01* -X121370827Y-118605602D01* -X121370814Y-118605609D01* -X121239711Y-118693210D01* -X121239707Y-118693213D01* -X121128213Y-118804707D01* -X121128210Y-118804711D01* -X121040609Y-118935814D01* -X121040602Y-118935827D01* -X120980264Y-119081498D01* -X120980261Y-119081510D01* -X120949500Y-119236153D01* -X120250500Y-119236153D01* -X120250500Y-117511888D01* -X122573765Y-117511888D01* -X122573765Y-117669581D01* -X122604526Y-117824224D01* -X122604529Y-117824236D01* -X122664867Y-117969907D01* -X122664874Y-117969920D01* -X122752475Y-118101023D01* -X122752478Y-118101027D01* -X122863972Y-118212521D01* -X122863976Y-118212524D01* -X122995079Y-118300125D01* -X122995092Y-118300132D01* -X123078640Y-118334738D01* -X123140768Y-118360472D01* -X123295418Y-118391234D01* -X123295421Y-118391235D01* -X123295423Y-118391235D01* -X123453109Y-118391235D01* -X123453110Y-118391234D01* -X123607762Y-118360472D01* -X123753444Y-118300129D01* -X123849191Y-118236153D01* -X124949500Y-118236153D01* -X124949500Y-118393846D01* -X124980261Y-118548489D01* -X124980264Y-118548501D01* -X125040602Y-118694172D01* -X125040609Y-118694185D01* -X125128210Y-118825288D01* -X125128213Y-118825292D01* -X125239707Y-118936786D01* -X125239711Y-118936789D01* -X125370814Y-119024390D01* -X125370827Y-119024397D01* -X125508683Y-119081498D01* -X125516503Y-119084737D01* -X125671153Y-119115499D01* -X125671156Y-119115500D01* -X125671158Y-119115500D01* -X125828844Y-119115500D01* -X125828845Y-119115499D01* -X125983497Y-119084737D01* -X126129179Y-119024394D01* -X126260289Y-118936789D01* -X126371789Y-118825289D01* -X126459394Y-118694179D01* -X126519737Y-118548497D01* -X126550500Y-118393842D01* -X126550500Y-118236158D01* -X126550500Y-118236155D01* -X126550499Y-118236153D01* -X126536963Y-118168102D01* -X126519737Y-118081503D01* -X126512901Y-118065000D01* -X126459397Y-117935827D01* -X126459390Y-117935814D01* -X126371789Y-117804711D01* -X126371786Y-117804707D01* -X126260292Y-117693213D01* -X126260288Y-117693210D01* -X126129185Y-117605609D01* -X126129172Y-117605602D01* -X125983501Y-117545264D01* -X125983489Y-117545261D01* -X125828845Y-117514500D01* -X125828842Y-117514500D01* -X125671158Y-117514500D01* -X125671155Y-117514500D01* -X125516510Y-117545261D01* -X125516498Y-117545264D01* -X125370827Y-117605602D01* -X125370814Y-117605609D01* -X125239711Y-117693210D01* -X125239707Y-117693213D01* -X125128213Y-117804707D01* -X125128210Y-117804711D01* -X125040609Y-117935814D01* -X125040602Y-117935827D01* -X124980264Y-118081498D01* -X124980261Y-118081510D01* -X124949500Y-118236153D01* -X123849191Y-118236153D01* -X123884554Y-118212524D01* -X123910292Y-118186786D01* -X123954694Y-118142385D01* -X123996051Y-118101027D01* -X123996054Y-118101024D01* -X124083659Y-117969914D01* -X124144002Y-117824232D01* -X124174765Y-117669577D01* -X124174765Y-117511893D01* -X124174765Y-117511890D01* -X124174764Y-117511888D01* -X124144003Y-117357245D01* -X124144002Y-117357238D01* -X124130769Y-117325291D01* -X124083662Y-117211562D01* -X124083655Y-117211549D01* -X123996054Y-117080446D01* -X123996051Y-117080442D01* -X123884557Y-116968948D01* -X123884553Y-116968945D01* -X123753450Y-116881344D01* -X123753437Y-116881337D01* -X123664809Y-116844627D01* -X123607766Y-116820999D01* -X123607754Y-116820996D01* -X123453110Y-116790235D01* -X123453107Y-116790235D01* -X123295423Y-116790235D01* -X123295420Y-116790235D01* -X123140775Y-116820996D01* -X123140763Y-116820999D01* -X122995092Y-116881337D01* -X122995079Y-116881344D01* -X122863976Y-116968945D01* -X122863972Y-116968948D01* -X122752478Y-117080442D01* -X122752475Y-117080446D01* -X122664874Y-117211549D01* -X122664867Y-117211562D01* -X122604529Y-117357233D01* -X122604526Y-117357245D01* -X122573765Y-117511888D01* -X120250500Y-117511888D01* -X120250500Y-116736153D01* -X128970134Y-116736153D01* -X128970134Y-116893846D01* -X129000895Y-117048489D01* -X129000898Y-117048501D01* -X129061236Y-117194172D01* -X129061243Y-117194185D01* -X129148844Y-117325288D01* -X129148847Y-117325292D01* -X129164419Y-117340864D01* -X129197904Y-117402187D01* -X129192920Y-117471879D01* -X129179842Y-117497433D01* -X129173534Y-117506872D01* -X129124499Y-117625255D01* -X129124497Y-117625261D01* -X129099500Y-117750928D01* -X129099500Y-117750931D01* -X129099500Y-117879069D01* -X129099500Y-117879071D01* -X129099499Y-117879071D01* -X129124497Y-118004738D01* -X129124499Y-118004744D01* -X129173533Y-118123124D01* -X129173538Y-118123133D01* -X129244723Y-118229668D01* -X129248589Y-118234379D01* -X129246958Y-118235716D01* -X129275858Y-118288642D01* -X129270874Y-118358334D01* -X129247489Y-118394719D01* -X129248589Y-118395621D01* -X129244723Y-118400331D01* -X129173538Y-118506866D01* -X129173533Y-118506875D01* -X129124499Y-118625255D01* -X129124497Y-118625261D01* -X129099500Y-118750928D01* -X129099500Y-118750931D01* -X129099500Y-118879069D01* -X129099500Y-118879071D01* -X129099499Y-118879071D01* -X129124497Y-119004738D01* -X129124500Y-119004748D01* -X129172281Y-119120102D01* -X129179750Y-119189571D01* -X129163401Y-119230066D01* -X129164113Y-119230447D01* -X129161236Y-119235828D01* -X129100898Y-119381498D01* -X129100895Y-119381510D01* -X129070134Y-119536153D01* -X129070134Y-119693846D01* -X129100895Y-119848489D01* -X129100898Y-119848501D01* -X129161236Y-119994172D01* -X129161243Y-119994185D01* -X129248844Y-120125288D01* -X129248847Y-120125292D01* -X129360341Y-120236786D01* -X129360345Y-120236789D01* -X129491448Y-120324390D01* -X129491461Y-120324397D01* -X129637132Y-120384735D01* -X129637137Y-120384737D01* -X129791787Y-120415499D01* -X129791790Y-120415500D01* -X129791792Y-120415500D01* -X129949478Y-120415500D01* -X129949479Y-120415499D01* -X130104131Y-120384737D01* -X130249813Y-120324394D01* -X130380923Y-120236789D01* -X130492423Y-120125289D01* -X130580028Y-119994179D01* -X130640371Y-119848497D01* -X130671134Y-119693842D01* -X130671134Y-119536158D01* -X130671134Y-119536155D01* -X130671133Y-119536153D01* -X130668793Y-119524390D01* -X130640371Y-119381503D01* -X130624773Y-119343846D01* -X130580028Y-119235820D01* -X130546841Y-119186153D01* -X132199500Y-119186153D01* -X132199500Y-119343846D01* -X132230261Y-119498489D01* -X132230264Y-119498501D01* -X132290602Y-119644172D01* -X132290609Y-119644185D01* -X132378210Y-119775288D01* -X132378213Y-119775292D01* -X132489707Y-119886786D01* -X132489711Y-119886789D01* -X132620814Y-119974390D01* -X132620827Y-119974397D01* -X132766498Y-120034735D01* -X132766503Y-120034737D01* -X132921153Y-120065499D01* -X132921156Y-120065500D01* -X132921158Y-120065500D01* -X133078844Y-120065500D01* -X133078845Y-120065499D01* -X133233497Y-120034737D01* -X133379179Y-119974394D01* -X133510289Y-119886789D01* -X133621789Y-119775289D01* -X133621792Y-119775283D01* -X133624351Y-119772725D01* -X133685674Y-119739240D01* -X133725537Y-119738884D01* -X133725693Y-119737303D01* -X133731756Y-119737900D01* -X133731758Y-119737900D01* -X133889444Y-119737900D01* -X133889445Y-119737899D01* -X134044097Y-119707137D01* -X134189779Y-119646794D01* -X134320889Y-119559189D01* -X134432389Y-119447689D01* -X134519994Y-119316579D01* -X134580337Y-119170897D01* -X134611100Y-119016242D01* -X134611100Y-118858558D01* -X134611100Y-118858555D01* -X134611099Y-118858553D01* -X134590443Y-118754711D01* -X134580337Y-118703903D01* -X134555198Y-118643211D01* -X134519997Y-118558227D01* -X134519990Y-118558214D01* -X134432389Y-118427111D01* -X134432386Y-118427107D01* -X134320892Y-118315613D01* -X134320888Y-118315610D01* -X134189785Y-118228009D01* -X134189772Y-118228002D01* -X134044101Y-118167664D01* -X134044089Y-118167661D01* -X133889445Y-118136900D01* -X133889442Y-118136900D01* -X133731758Y-118136900D01* -X133731755Y-118136900D01* -X133577110Y-118167661D01* -X133577098Y-118167664D01* -X133431427Y-118228002D01* -X133431414Y-118228009D01* -X133300311Y-118315610D01* -X133186246Y-118429675D01* -X133124923Y-118463159D01* -X133085060Y-118463524D01* -X133084906Y-118465097D01* -X133078844Y-118464500D01* -X133078842Y-118464500D01* -X132921158Y-118464500D01* -X132921155Y-118464500D01* -X132766510Y-118495261D01* -X132766498Y-118495264D01* -X132620827Y-118555602D01* -X132620814Y-118555609D01* -X132489711Y-118643210D01* -X132489707Y-118643213D01* -X132378213Y-118754707D01* -X132378210Y-118754711D01* -X132290609Y-118885814D01* -X132290602Y-118885827D01* -X132230264Y-119031498D01* -X132230261Y-119031510D01* -X132199500Y-119186153D01* -X130546841Y-119186153D01* -X130492423Y-119104711D01* -X130492420Y-119104707D01* -X130425181Y-119037468D01* -X130391696Y-118976145D01* -X130391245Y-118925594D01* -X130397561Y-118893846D01* -X130400500Y-118879069D01* -X130400500Y-118750931D01* -X130400500Y-118750928D01* -X130375502Y-118625261D01* -X130375501Y-118625260D01* -X130375501Y-118625256D01* -X130326465Y-118506873D01* -X130326464Y-118506872D01* -X130326461Y-118506866D01* -X130255276Y-118400331D01* -X130251411Y-118395621D01* -X130253045Y-118394279D01* -X130224148Y-118341389D01* -X130229114Y-118271696D01* -X130252514Y-118235284D01* -X130251411Y-118234379D01* -X130255271Y-118229673D01* -X130255276Y-118229669D01* -X130326465Y-118123127D01* -X130375501Y-118004744D01* -X130387547Y-117944185D01* -X130400500Y-117879071D01* -X130400500Y-117750928D01* -X130375502Y-117625261D01* -X130375501Y-117625260D01* -X130375501Y-117625256D01* -X130343708Y-117548501D01* -X130324306Y-117501659D01* -X130322639Y-117486153D01* -X130649500Y-117486153D01* -X130649500Y-117643846D01* -X130680261Y-117798489D01* -X130680264Y-117798501D01* -X130740602Y-117944172D01* -X130740609Y-117944185D01* -X130828210Y-118075288D01* -X130828213Y-118075292D01* -X130939707Y-118186786D01* -X130939711Y-118186789D01* -X131070814Y-118274390D01* -X131070827Y-118274397D01* -X131170328Y-118315611D01* -X131216503Y-118334737D01* -X131345871Y-118360470D01* -X131371153Y-118365499D01* -X131371156Y-118365500D01* -X131371158Y-118365500D01* -X131528844Y-118365500D01* -X131528845Y-118365499D01* -X131683497Y-118334737D01* -X131829179Y-118274394D01* -X131960289Y-118186789D01* -X132071789Y-118075289D01* -X132159394Y-117944179D01* -X132162854Y-117935827D01* -X132208640Y-117825288D01* -X132219737Y-117798497D01* -X132250500Y-117643842D01* -X132250500Y-117486158D01* -X132250500Y-117486155D01* -X132250499Y-117486153D01* -X132219738Y-117331510D01* -X132219737Y-117331503D01* -X132180242Y-117236153D01* -X135449500Y-117236153D01* -X135449500Y-117393846D01* -X135480261Y-117548489D01* -X135480264Y-117548501D01* -X135540602Y-117694172D01* -X135540609Y-117694185D01* -X135628210Y-117825288D01* -X135628213Y-117825292D01* -X135739707Y-117936786D01* -X135739710Y-117936788D01* -X135739711Y-117936789D01* -X135750771Y-117944179D01* -X135777289Y-117961898D01* -X135822093Y-118015511D01* -X135830800Y-118084836D01* -X135800645Y-118147863D01* -X135777289Y-118168102D01* -X135739707Y-118193213D01* -X135628213Y-118304707D01* -X135628210Y-118304711D01* -X135540609Y-118435814D01* -X135540602Y-118435827D01* -X135480264Y-118581498D01* -X135480261Y-118581510D01* -X135449500Y-118736153D01* -X135449500Y-118893846D01* -X135480261Y-119048489D01* -X135480264Y-119048501D01* -X135540602Y-119194172D01* -X135540609Y-119194185D01* -X135628210Y-119325288D01* -X135628213Y-119325292D01* -X135739707Y-119436786D01* -X135739711Y-119436789D01* -X135870814Y-119524390D01* -X135870827Y-119524397D01* -X135954824Y-119559189D01* -X136016503Y-119584737D01* -X136171153Y-119615499D01* -X136171156Y-119615500D01* -X136171158Y-119615500D01* -X136328844Y-119615500D01* -X136328845Y-119615499D01* -X136483497Y-119584737D01* -X136629179Y-119524394D01* -X136760289Y-119436789D01* -X136871789Y-119325289D01* -X136959394Y-119194179D01* -X136962719Y-119186153D01* -X136991984Y-119115499D01* -X137019737Y-119048497D01* -X137050500Y-118893842D01* -X137050500Y-118736158D01* -X137050500Y-118736155D01* -X137050499Y-118736153D01* -X137032012Y-118643213D01* -X137019737Y-118581503D01* -X137010093Y-118558221D01* -X136959397Y-118435827D01* -X136959390Y-118435814D01* -X136871789Y-118304711D01* -X136871786Y-118304707D01* -X136760292Y-118193213D01* -X136760284Y-118193207D01* -X136722712Y-118168102D01* -X136677906Y-118114490D01* -X136669199Y-118045165D01* -X136699353Y-117982138D01* -X136722712Y-117961898D01* -X136749279Y-117944145D01* -X136760289Y-117936789D01* -X136871789Y-117825289D01* -X136959394Y-117694179D01* -X137019737Y-117548497D01* -X137050500Y-117393842D01* -X137050500Y-117236158D01* -X137050500Y-117236155D01* -X137050499Y-117236153D01* -X137050125Y-117234271D01* -X137019737Y-117081503D01* -X137019298Y-117080442D01* -X136959397Y-116935827D01* -X136959390Y-116935814D01* -X136871789Y-116804711D01* -X136871786Y-116804707D01* -X136760292Y-116693213D01* -X136760288Y-116693210D01* -X136629185Y-116605609D01* -X136629172Y-116605602D01* -X136483501Y-116545264D01* -X136483489Y-116545261D01* -X136328845Y-116514500D01* -X136328842Y-116514500D01* -X136171158Y-116514500D01* -X136171155Y-116514500D01* -X136016510Y-116545261D01* -X136016498Y-116545264D01* -X135870827Y-116605602D01* -X135870814Y-116605609D01* -X135739711Y-116693210D01* -X135739707Y-116693213D01* -X135628213Y-116804707D01* -X135628210Y-116804711D01* -X135540609Y-116935814D01* -X135540602Y-116935827D01* -X135480264Y-117081498D01* -X135480261Y-117081510D01* -X135449500Y-117236153D01* -X132180242Y-117236153D01* -X132179933Y-117235408D01* -X132159397Y-117185827D01* -X132159390Y-117185814D01* -X132071789Y-117054711D01* -X132071786Y-117054707D01* -X131960292Y-116943213D01* -X131960288Y-116943210D01* -X131829185Y-116855609D01* -X131829172Y-116855602D01* -X131683501Y-116795264D01* -X131683489Y-116795261D01* -X131528845Y-116764500D01* -X131528842Y-116764500D01* -X131371158Y-116764500D01* -X131371155Y-116764500D01* -X131216510Y-116795261D01* -X131216498Y-116795264D01* -X131070827Y-116855602D01* -X131070814Y-116855609D01* -X130939711Y-116943210D01* -X130939707Y-116943213D01* -X130828213Y-117054707D01* -X130828210Y-117054711D01* -X130767395Y-117145726D01* -X130767391Y-117145734D01* -X130740606Y-117185821D01* -X130680263Y-117331503D01* -X130679324Y-117336220D01* -X130679322Y-117336226D01* -X130649500Y-117486153D01* -X130322639Y-117486153D01* -X130316837Y-117432190D01* -X130348112Y-117369711D01* -X130351187Y-117366525D01* -X130392421Y-117325291D01* -X130392423Y-117325289D01* -X130480028Y-117194179D01* -X130540371Y-117048497D01* -X130571134Y-116893842D01* -X130571134Y-116736158D01* -X130571134Y-116736155D01* -X130571133Y-116736153D01* -X130545165Y-116605606D01* -X130540371Y-116581503D01* -X130540369Y-116581498D01* -X130480031Y-116435827D01* -X130480024Y-116435814D01* -X130392423Y-116304711D01* -X130392420Y-116304707D01* -X130280926Y-116193213D01* -X130280922Y-116193210D01* -X130149819Y-116105609D01* -X130149806Y-116105602D01* -X130004135Y-116045264D01* -X130004123Y-116045261D01* -X129849479Y-116014500D01* -X129849476Y-116014500D01* -X129691792Y-116014500D01* -X129691789Y-116014500D01* -X129537144Y-116045261D01* -X129537132Y-116045264D01* -X129391461Y-116105602D01* -X129391448Y-116105609D01* -X129260345Y-116193210D01* -X129260341Y-116193213D01* -X129148847Y-116304707D01* -X129148844Y-116304711D01* -X129061243Y-116435814D01* -X129061236Y-116435827D01* -X129000898Y-116581498D01* -X129000895Y-116581510D01* -X128970134Y-116736153D01* -X120250500Y-116736153D01* -X120250500Y-114221153D01* -X136649500Y-114221153D01* -X136649500Y-114378846D01* -X136680261Y-114533489D01* -X136680264Y-114533501D01* -X136740602Y-114679172D01* -X136740609Y-114679185D01* -X136828210Y-114810288D01* -X136828213Y-114810292D01* -X136939707Y-114921786D01* -X136939711Y-114921789D01* -X137070814Y-115009390D01* -X137070827Y-115009397D01* -X137216498Y-115069735D01* -X137216503Y-115069737D01* -X137371153Y-115100499D01* -X137371156Y-115100500D01* -X137371158Y-115100500D01* -X137528844Y-115100500D01* -X137528845Y-115100499D01* -X137683497Y-115069737D01* -X137829179Y-115009394D01* -X137960289Y-114921789D01* -X138071789Y-114810289D01* -X138144453Y-114701540D01* -X145554200Y-114701540D01* -X145554200Y-114848459D01* -X145582858Y-114992534D01* -X145582861Y-114992544D01* -X145639078Y-115128266D01* -X145639083Y-115128275D01* -X145720698Y-115250419D01* -X145720701Y-115250423D01* -X145824576Y-115354298D01* -X145824580Y-115354301D01* -X145946724Y-115435916D01* -X145946730Y-115435919D01* -X145946731Y-115435920D01* -X146082458Y-115492140D01* -X146226540Y-115520799D01* -X146226544Y-115520800D01* -X146226545Y-115520800D01* -X146373456Y-115520800D01* -X146373457Y-115520799D01* -X146517542Y-115492140D01* -X146653269Y-115435920D01* -X146775420Y-115354301D01* -X146879301Y-115250420D01* -X146960920Y-115128269D01* -X147017140Y-114992542D01* -X147045800Y-114848455D01* -X147045800Y-114701545D01* -X147017140Y-114557458D01* -X146960920Y-114421731D01* -X146960919Y-114421730D01* -X146960916Y-114421724D01* -X146879301Y-114299580D01* -X146879298Y-114299576D01* -X146775423Y-114195701D01* -X146775419Y-114195698D01* -X146653275Y-114114083D01* -X146653266Y-114114078D01* -X146517544Y-114057861D01* -X146517545Y-114057861D01* -X146517542Y-114057860D01* -X146517538Y-114057859D01* -X146517534Y-114057858D01* -X146373459Y-114029200D01* -X146373455Y-114029200D01* -X146226545Y-114029200D01* -X146226540Y-114029200D01* -X146082465Y-114057858D01* -X146082455Y-114057861D01* -X145946733Y-114114078D01* -X145946724Y-114114083D01* -X145824580Y-114195698D01* -X145824576Y-114195701D01* -X145720701Y-114299576D01* -X145720698Y-114299580D01* -X145639083Y-114421724D01* -X145639078Y-114421733D01* -X145582861Y-114557455D01* -X145582858Y-114557465D01* -X145554200Y-114701540D01* -X138144453Y-114701540D01* -X138159394Y-114679179D01* -X138219737Y-114533497D01* -X138250500Y-114378842D01* -X138250500Y-114221158D01* -X138250500Y-114221155D01* -X138250499Y-114221153D01* -X138229201Y-114114083D01* -X138219737Y-114066503D01* -X138204286Y-114029200D01* -X138159397Y-113920827D01* -X138159390Y-113920814D01* -X138071789Y-113789711D01* -X138071786Y-113789707D01* -X137960292Y-113678213D01* -X137960288Y-113678210D01* -X137829185Y-113590609D01* -X137829172Y-113590602D01* -X137683501Y-113530264D01* -X137683489Y-113530261D01* -X137528845Y-113499500D01* -X137528842Y-113499500D01* -X137371158Y-113499500D01* -X137371155Y-113499500D01* -X137216510Y-113530261D01* -X137216498Y-113530264D01* -X137070827Y-113590602D01* -X137070814Y-113590609D01* -X136939711Y-113678210D01* -X136939707Y-113678213D01* -X136828213Y-113789707D01* -X136828210Y-113789711D01* -X136740609Y-113920814D01* -X136740602Y-113920827D01* -X136680264Y-114066498D01* -X136680261Y-114066510D01* -X136649500Y-114221153D01* -X120250500Y-114221153D01* -X120250500Y-110902753D01* -X140316200Y-110902753D01* -X140316200Y-111060446D01* -X140346961Y-111215089D01* -X140346964Y-111215101D01* -X140407302Y-111360772D01* -X140407309Y-111360785D01* -X140494910Y-111491888D01* -X140494913Y-111491892D01* -X140606407Y-111603386D01* -X140606411Y-111603389D01* -X140737514Y-111690990D01* -X140737527Y-111690997D01* -X140841304Y-111733982D01* -X140883203Y-111751337D01* -X141037853Y-111782099D01* -X141037856Y-111782100D01* -X141037858Y-111782100D01* -X141195544Y-111782100D01* -X141195545Y-111782099D01* -X141350197Y-111751337D01* -X141495879Y-111690994D01* -X141626989Y-111603389D01* -X141738489Y-111491889D01* -X141826094Y-111360779D01* -X141886437Y-111215097D01* -X141913473Y-111079179D01* -X141917338Y-111059750D01* -X141949723Y-110997839D01* -X141951217Y-110996317D01* -X142326381Y-110621153D01* -X144149500Y-110621153D01* -X144149500Y-110778846D01* -X144180261Y-110933489D01* -X144180264Y-110933501D01* -X144240602Y-111079172D01* -X144240609Y-111079185D01* -X144328210Y-111210288D01* -X144328213Y-111210292D01* -X144439707Y-111321786D01* -X144439711Y-111321789D01* -X144570814Y-111409390D01* -X144570827Y-111409397D01* -X144716498Y-111469735D01* -X144716503Y-111469737D01* -X144871153Y-111500499D01* -X144871156Y-111500500D01* -X144871158Y-111500500D01* -X145028844Y-111500500D01* -X145028845Y-111500499D01* -X145183497Y-111469737D01* -X145329179Y-111409394D01* -X145460289Y-111321789D01* -X145571789Y-111210289D01* -X145659394Y-111079179D01* -X145719737Y-110933497D01* -X145750500Y-110778842D01* -X145750500Y-110621158D01* -X145750500Y-110621155D01* -X145750499Y-110621153D01* -X145731847Y-110527385D01* -X145719737Y-110466503D01* -X145704926Y-110430747D01* -X145697458Y-110361281D01* -X145728732Y-110298802D01* -X145750591Y-110280199D01* -X145759420Y-110274301D01* -X145863301Y-110170420D01* -X145944920Y-110048269D01* -X146001140Y-109912542D01* -X146029800Y-109768455D01* -X146029800Y-109621545D01* -X146001140Y-109477458D01* -X145944920Y-109341731D01* -X145944919Y-109341730D01* -X145944916Y-109341724D01* -X145863301Y-109219580D01* -X145863298Y-109219576D01* -X145759423Y-109115701D01* -X145759419Y-109115698D01* -X145637275Y-109034083D01* -X145637266Y-109034078D01* -X145526611Y-108988244D01* -X145501542Y-108977860D01* -X145501538Y-108977859D01* -X145501534Y-108977858D01* -X145357459Y-108949200D01* -X145357455Y-108949200D01* -X145210545Y-108949200D01* -X145210540Y-108949200D01* -X145066465Y-108977858D01* -X145066455Y-108977861D01* -X144930733Y-109034078D01* -X144930724Y-109034083D01* -X144808580Y-109115698D01* -X144808576Y-109115701D01* -X144704701Y-109219576D01* -X144704698Y-109219580D01* -X144623083Y-109341724D01* -X144623078Y-109341733D01* -X144566861Y-109477455D01* -X144566858Y-109477465D01* -X144538200Y-109621540D01* -X144538200Y-109621544D01* -X144538200Y-109621545D01* -X144538200Y-109768455D01* -X144538201Y-109768459D01* -X144564867Y-109902523D01* -X144558638Y-109972114D01* -X144515775Y-110027291D01* -X144512140Y-110029815D01* -X144439711Y-110078210D01* -X144439707Y-110078213D01* -X144328213Y-110189707D01* -X144328210Y-110189711D01* -X144240609Y-110320814D01* -X144240602Y-110320827D01* -X144180264Y-110466498D01* -X144180261Y-110466510D01* -X144149500Y-110621153D01* -X142326381Y-110621153D01* -X144687017Y-108260519D01* -X144748340Y-108227034D01* -X144774698Y-108224200D01* -X145271034Y-108224200D01* -X145338073Y-108243885D01* -X145339925Y-108245098D01* -X145471614Y-108333090D01* -X145471627Y-108333097D01* -X145617298Y-108393435D01* -X145617303Y-108393437D01* -X145759822Y-108421786D01* -X145771953Y-108424199D01* -X145771956Y-108424200D01* -X145771958Y-108424200D01* -X145929644Y-108424200D01* -X145929645Y-108424199D01* -X146084297Y-108393437D01* -X146229979Y-108333094D01* -X146361089Y-108245489D01* -X146472589Y-108133989D01* -X146560194Y-108002879D01* -X146620537Y-107857197D01* -X146651300Y-107702542D01* -X146651300Y-107544858D01* -X146651300Y-107544855D01* -X146651299Y-107544853D01* -X146633930Y-107457533D01* -X146620537Y-107390203D01* -X146599176Y-107338632D01* -X146560197Y-107244527D01* -X146560190Y-107244514D01* -X146472589Y-107113411D01* -X146472586Y-107113407D01* -X146361092Y-107001913D01* -X146361088Y-107001910D01* -X146229985Y-106914309D01* -X146229972Y-106914302D01* -X146084301Y-106853964D01* -X146084289Y-106853961D01* -X145929645Y-106823200D01* -X145929642Y-106823200D01* -X145771958Y-106823200D01* -X145771955Y-106823200D01* -X145617310Y-106853961D01* -X145617298Y-106853964D01* -X145471627Y-106914302D01* -X145471614Y-106914309D01* -X145339925Y-107002302D01* -X145273247Y-107023180D01* -X145271034Y-107023200D01* -X144561270Y-107023200D01* -X144561254Y-107023199D01* -X144553658Y-107023199D01* -X144395543Y-107023199D01* -X144319179Y-107043661D01* -X144242814Y-107064123D01* -X144242809Y-107064126D01* -X144105890Y-107143175D01* -X144105882Y-107143181D01* -X141102039Y-110147025D01* -X141040716Y-110180510D01* -X141038550Y-110180961D01* -X140883208Y-110211861D01* -X140883198Y-110211864D01* -X140737527Y-110272202D01* -X140737514Y-110272209D01* -X140606411Y-110359810D01* -X140606407Y-110359813D01* -X140494913Y-110471307D01* -X140494910Y-110471311D01* -X140407309Y-110602414D01* -X140407302Y-110602427D01* -X140346964Y-110748098D01* -X140346961Y-110748110D01* -X140316200Y-110902753D01* -X120250500Y-110902753D01* -X120250500Y-107071153D01* -X120499500Y-107071153D01* -X120499500Y-107228846D01* -X120530261Y-107383489D01* -X120530264Y-107383501D01* -X120590602Y-107529172D01* -X120590609Y-107529185D01* -X120678210Y-107660288D01* -X120678213Y-107660292D01* -X120789707Y-107771786D01* -X120789711Y-107771789D01* -X120920814Y-107859390D01* -X120920827Y-107859397D01* -X120996181Y-107890609D01* -X121066503Y-107919737D01* -X121221153Y-107950499D01* -X121221156Y-107950500D01* -X121221158Y-107950500D01* -X121378844Y-107950500D01* -X121378845Y-107950499D01* -X121533497Y-107919737D01* -X121679179Y-107859394D01* -X121810289Y-107771789D01* -X121860925Y-107721153D01* -X130149500Y-107721153D01* -X130149500Y-107878846D01* -X130180261Y-108033489D01* -X130180264Y-108033501D01* -X130240602Y-108179172D01* -X130240609Y-108179185D01* -X130328210Y-108310288D01* -X130328213Y-108310292D01* -X130439707Y-108421786D01* -X130439711Y-108421789D01* -X130570814Y-108509390D01* -X130570827Y-108509397D01* -X130716387Y-108569689D01* -X130716503Y-108569737D01* -X130871153Y-108600499D01* -X130871156Y-108600500D01* -X130871158Y-108600500D01* -X131028844Y-108600500D01* -X131028845Y-108600499D01* -X131183497Y-108569737D01* -X131329179Y-108509394D01* -X131460289Y-108421789D01* -X131571789Y-108310289D01* -X131659394Y-108179179D01* -X131719737Y-108033497D01* -X131750500Y-107878842D01* -X131750500Y-107721158D01* -X131750500Y-107721155D01* -X131750499Y-107721153D01* -X131734943Y-107642949D01* -X131719737Y-107566503D01* -X131719721Y-107566464D01* -X131659397Y-107420827D01* -X131659390Y-107420814D01* -X131571789Y-107289711D01* -X131571786Y-107289707D01* -X131460292Y-107178213D01* -X131460288Y-107178210D01* -X131329185Y-107090609D01* -X131329172Y-107090602D01* -X131183501Y-107030264D01* -X131183489Y-107030261D01* -X131028845Y-106999500D01* -X131028842Y-106999500D01* -X130871158Y-106999500D01* -X130871155Y-106999500D01* -X130716510Y-107030261D01* -X130716498Y-107030264D01* -X130570827Y-107090602D01* -X130570814Y-107090609D01* -X130439711Y-107178210D01* -X130439707Y-107178213D01* -X130328213Y-107289707D01* -X130328210Y-107289711D01* -X130240609Y-107420814D01* -X130240602Y-107420827D01* -X130180264Y-107566498D01* -X130180261Y-107566510D01* -X130149500Y-107721153D01* -X121860925Y-107721153D01* -X121921789Y-107660289D01* -X121933376Y-107642949D01* -X122009390Y-107529185D01* -X122009390Y-107529184D01* -X122009394Y-107529179D01* -X122069737Y-107383497D01* -X122100500Y-107228842D01* -X122100500Y-107071158D01* -X122100500Y-107071155D01* -X122100499Y-107071153D01* -X122090960Y-107023199D01* -X122069737Y-106916503D01* -X122043832Y-106853963D01* -X122016327Y-106787558D01* -X122016311Y-106787520D01* -X122015679Y-106785995D01* -X122009394Y-106770821D01* -X122009391Y-106770816D01* -X122009390Y-106770814D01* -X121992912Y-106746153D01* -X134449500Y-106746153D01* -X134449500Y-106903846D01* -X134480261Y-107058489D01* -X134480264Y-107058501D01* -X134540602Y-107204172D01* -X134540609Y-107204185D01* -X134628210Y-107335288D01* -X134628213Y-107335292D01* -X134739707Y-107446786D01* -X134739711Y-107446789D01* -X134870814Y-107534390D01* -X134870827Y-107534397D01* -X134948356Y-107566510D01* -X135016503Y-107594737D01* -X135054443Y-107602283D01* -X135096068Y-107610564D01* -X135157979Y-107642949D01* -X135192553Y-107703664D01* -X135188814Y-107773434D01* -X135159562Y-107819858D01* -X135153515Y-107825904D01* -X135153510Y-107825911D01* -X135065909Y-107957014D01* -X135065902Y-107957027D01* -X135005564Y-108102698D01* -X135005561Y-108102710D01* -X134974800Y-108257353D01* -X134974800Y-108415046D01* -X135005561Y-108569689D01* -X135005564Y-108569701D01* -X135065902Y-108715372D01* -X135065909Y-108715385D01* -X135153510Y-108846488D01* -X135153513Y-108846492D01* -X135265007Y-108957986D01* -X135265011Y-108957989D01* -X135396114Y-109045590D01* -X135396127Y-109045597D01* -X135541798Y-109105935D01* -X135541803Y-109105937D01* -X135694342Y-109136279D01* -X135696453Y-109136699D01* -X135696456Y-109136700D01* -X135696458Y-109136700D01* -X135854144Y-109136700D01* -X135854145Y-109136699D01* -X136008797Y-109105937D01* -X136154479Y-109045594D01* -X136285589Y-108957989D01* -X136397089Y-108846489D01* -X136484694Y-108715379D01* -X136545037Y-108569697D01* -X136554693Y-108521153D01* -X139699500Y-108521153D01* -X139699500Y-108678846D01* -X139730261Y-108833489D01* -X139730264Y-108833501D01* -X139790602Y-108979172D01* -X139790609Y-108979185D01* -X139878210Y-109110288D01* -X139878213Y-109110292D01* -X139989707Y-109221786D01* -X139989711Y-109221789D01* -X140120814Y-109309390D01* -X140120827Y-109309397D01* -X140266498Y-109369735D01* -X140266503Y-109369737D01* -X140421153Y-109400499D01* -X140421156Y-109400500D01* -X140421158Y-109400500D01* -X140578844Y-109400500D01* -X140578845Y-109400499D01* -X140733497Y-109369737D01* -X140879179Y-109309394D01* -X141010289Y-109221789D01* -X141121789Y-109110289D01* -X141209394Y-108979179D01* -X141269737Y-108833497D01* -X141300500Y-108678842D01* -X141300500Y-108521158D01* -X141300500Y-108521155D01* -X141300499Y-108521153D01* -X141294476Y-108490874D01* -X141269737Y-108366503D01* -X141246452Y-108310288D01* -X141209397Y-108220827D01* -X141209390Y-108220814D01* -X141121789Y-108089711D01* -X141121786Y-108089707D01* -X141010292Y-107978213D01* -X141010288Y-107978210D01* -X140879185Y-107890609D01* -X140879172Y-107890602D01* -X140733501Y-107830264D01* -X140733489Y-107830261D01* -X140578845Y-107799500D01* -X140578842Y-107799500D01* -X140421158Y-107799500D01* -X140421155Y-107799500D01* -X140266510Y-107830261D01* -X140266498Y-107830264D01* -X140120827Y-107890602D01* -X140120814Y-107890609D01* -X139989711Y-107978210D01* -X139989707Y-107978213D01* -X139878213Y-108089707D01* -X139878210Y-108089711D01* -X139790609Y-108220814D01* -X139790602Y-108220827D01* -X139730264Y-108366498D01* -X139730261Y-108366510D01* -X139699500Y-108521153D01* -X136554693Y-108521153D01* -X136556416Y-108512490D01* -X136560716Y-108490875D01* -X136560716Y-108490874D01* -X136575800Y-108415044D01* -X136575800Y-108257355D01* -X136575799Y-108257353D01* -X136560248Y-108179172D01* -X136545037Y-108102703D01* -X136516368Y-108033489D01* -X136484697Y-107957027D01* -X136484690Y-107957014D01* -X136397089Y-107825911D01* -X136397086Y-107825907D01* -X136285592Y-107714413D01* -X136285588Y-107714410D01* -X136154485Y-107626809D01* -X136154472Y-107626802D01* -X136008801Y-107566464D01* -X136008791Y-107566461D01* -X135929230Y-107550635D01* -X135867319Y-107518249D01* -X135832745Y-107457533D01* -X135836486Y-107387764D01* -X135865745Y-107341333D01* -X135871788Y-107335290D01* -X135871789Y-107335289D01* -X135959394Y-107204179D01* -X136019737Y-107058497D01* -X136050500Y-106903842D01* -X136050500Y-106746158D01* -X136050500Y-106746155D01* -X136050499Y-106746153D01* -X136019738Y-106591510D01* -X136019737Y-106591503D01* -X135993521Y-106528211D01* -X135959397Y-106445827D01* -X135959389Y-106445813D01* -X135951468Y-106433958D01* -X135951467Y-106433957D01* -X135909503Y-106371153D01* -X142499500Y-106371153D01* -X142499500Y-106528846D01* -X142530261Y-106683489D01* -X142530264Y-106683501D01* -X142590602Y-106829172D01* -X142590609Y-106829185D01* -X142678210Y-106960288D01* -X142678213Y-106960292D01* -X142789707Y-107071786D01* -X142789711Y-107071789D01* -X142920814Y-107159390D01* -X142920827Y-107159397D01* -X143066498Y-107219735D01* -X143066503Y-107219737D01* -X143191065Y-107244514D01* -X143221153Y-107250499D01* -X143221156Y-107250500D01* -X143221158Y-107250500D01* -X143378844Y-107250500D01* -X143378845Y-107250499D01* -X143533497Y-107219737D01* -X143679179Y-107159394D01* -X143810289Y-107071789D01* -X143921789Y-106960289D01* -X144009394Y-106829179D01* -X144069737Y-106683497D01* -X144100500Y-106528842D01* -X144100500Y-106371158D01* -X144100500Y-106371155D01* -X144100499Y-106371153D01* -X144069738Y-106216510D01* -X144069737Y-106216503D01* -X144027946Y-106115609D01* -X144009397Y-106070827D01* -X144009390Y-106070814D01* -X143921789Y-105939711D01* -X143921786Y-105939707D01* -X143810292Y-105828213D01* -X143810288Y-105828210D01* -X143679185Y-105740609D01* -X143679172Y-105740602D01* -X143533501Y-105680264D01* -X143533489Y-105680261D01* -X143378845Y-105649500D01* -X143378842Y-105649500D01* -X143221158Y-105649500D01* -X143221155Y-105649500D01* -X143066510Y-105680261D01* -X143066498Y-105680264D01* -X142920827Y-105740602D01* -X142920814Y-105740609D01* -X142789711Y-105828210D01* -X142789707Y-105828213D01* -X142678213Y-105939707D01* -X142678210Y-105939711D01* -X142590609Y-106070814D01* -X142590602Y-106070827D01* -X142530264Y-106216498D01* -X142530261Y-106216510D01* -X142499500Y-106371153D01* -X135909503Y-106371153D01* -X135871789Y-106314711D01* -X135871786Y-106314707D01* -X135760292Y-106203213D01* -X135760288Y-106203210D01* -X135629185Y-106115609D01* -X135629172Y-106115602D01* -X135483501Y-106055264D01* -X135483489Y-106055261D01* -X135328845Y-106024500D01* -X135328842Y-106024500D01* -X135171158Y-106024500D01* -X135171155Y-106024500D01* -X135016510Y-106055261D01* -X135016498Y-106055264D01* -X134870827Y-106115602D01* -X134870814Y-106115609D01* -X134739711Y-106203210D01* -X134739707Y-106203213D01* -X134628213Y-106314707D01* -X134628210Y-106314711D01* -X134540609Y-106445814D01* -X134540602Y-106445827D01* -X134480264Y-106591498D01* -X134480261Y-106591510D01* -X134449500Y-106746153D01* -X121992912Y-106746153D01* -X121921789Y-106639711D01* -X121921786Y-106639707D01* -X121810292Y-106528213D01* -X121810288Y-106528210D01* -X121679185Y-106440609D01* -X121679172Y-106440602D01* -X121533501Y-106380264D01* -X121533489Y-106380261D01* -X121378845Y-106349500D01* -X121378842Y-106349500D01* -X121221158Y-106349500D01* -X121221155Y-106349500D01* -X121066510Y-106380261D01* -X121066498Y-106380264D01* -X120920827Y-106440602D01* -X120920814Y-106440609D01* -X120789711Y-106528210D01* -X120789707Y-106528213D01* -X120678213Y-106639707D01* -X120678210Y-106639711D01* -X120590609Y-106770814D01* -X120590602Y-106770827D01* -X120530264Y-106916498D01* -X120530261Y-106916510D01* -X120499500Y-107071153D01* -X120250500Y-107071153D01* -X120250500Y-105071153D01* -X121549500Y-105071153D01* -X121549500Y-105228846D01* -X121580261Y-105383489D01* -X121580264Y-105383501D01* -X121640602Y-105529172D01* -X121640609Y-105529185D01* -X121728210Y-105660288D01* -X121728213Y-105660292D01* -X121839707Y-105771786D01* -X121839711Y-105771789D01* -X121970814Y-105859390D01* -X121970827Y-105859397D01* -X122092269Y-105909699D01* -X122116503Y-105919737D01* -X122271153Y-105950499D01* -X122271156Y-105950500D01* -X122271158Y-105950500D01* -X122428844Y-105950500D01* -X122428845Y-105950499D01* -X122583497Y-105919737D01* -X122729179Y-105859394D01* -X122860289Y-105771789D01* -X122971789Y-105660289D01* -X123059394Y-105529179D01* -X123059395Y-105529176D01* -X123059397Y-105529173D01* -X123112940Y-105399906D01* -X123156780Y-105345502D01* -X123203309Y-105325741D01* -X123233497Y-105319737D01* -X123379179Y-105259394D01* -X123510289Y-105171789D01* -X123621789Y-105060289D01* -X123709394Y-104929179D01* -X123769737Y-104783497D01* -X123792282Y-104670158D01* -X123792283Y-104670153D01* -X124159100Y-104670153D01* -X124159100Y-104827846D01* -X124189861Y-104982489D01* -X124189864Y-104982501D01* -X124250202Y-105128172D01* -X124250209Y-105128185D01* -X124337810Y-105259288D01* -X124337813Y-105259292D01* -X124449307Y-105370786D01* -X124449311Y-105370789D01* -X124580414Y-105458390D01* -X124580427Y-105458397D01* -X124652826Y-105488385D01* -X124726103Y-105518737D01* -X124880753Y-105549499D01* -X124880756Y-105549500D01* -X124880758Y-105549500D01* -X125038444Y-105549500D01* -X125038445Y-105549499D01* -X125193097Y-105518737D01* -X125338779Y-105458394D01* -X125469889Y-105370789D01* -X125581389Y-105259289D01* -X125668994Y-105128179D01* -X125729337Y-104982497D01* -X125760100Y-104827842D01* -X125760100Y-104670158D01* -X125760100Y-104670155D01* -X125760099Y-104670153D01* -X125729337Y-104515503D01* -X125710380Y-104469736D01* -X125668997Y-104369827D01* -X125668990Y-104369814D01* -X125581389Y-104238711D01* -X125581386Y-104238707D01* -X125469892Y-104127213D01* -X125469888Y-104127210D01* -X125338785Y-104039609D01* -X125338772Y-104039602D01* -X125193101Y-103979264D01* -X125193089Y-103979261D01* -X125038445Y-103948500D01* -X125038442Y-103948500D01* -X124880758Y-103948500D01* -X124880755Y-103948500D01* -X124726110Y-103979261D01* -X124726098Y-103979264D01* -X124580427Y-104039602D01* -X124580414Y-104039609D01* -X124449311Y-104127210D01* -X124449307Y-104127213D01* -X124337813Y-104238707D01* -X124337810Y-104238711D01* -X124250209Y-104369814D01* -X124250202Y-104369827D01* -X124189864Y-104515498D01* -X124189861Y-104515510D01* -X124159100Y-104670153D01* -X123792283Y-104670153D01* -X123798306Y-104639875D01* -X123798306Y-104639874D01* -X123800500Y-104628844D01* -X123800500Y-104471155D01* -X123800499Y-104471153D01* -X123780344Y-104369827D01* -X123769737Y-104316503D01* -X123733427Y-104228842D01* -X123709397Y-104170827D01* -X123709390Y-104170814D01* -X123621789Y-104039711D01* -X123621786Y-104039707D01* -X123510292Y-103928213D01* -X123510286Y-103928208D01* -X123497710Y-103919805D01* -X123452906Y-103866193D01* -X123444199Y-103796867D01* -X123474354Y-103733840D01* -X123497708Y-103713603D01* -X123560289Y-103671789D01* -X123671789Y-103560289D01* -X123759394Y-103429179D01* -X123819737Y-103283497D01* -X123850500Y-103128842D01* -X123850500Y-102971158D01* -X123850500Y-102971155D01* -X123850499Y-102971153D01* -X123828447Y-102860292D01* -X123819737Y-102816503D01* -X123783569Y-102729185D01* -X123759397Y-102670827D01* -X123759390Y-102670814D01* -X123671789Y-102539711D01* -X123671786Y-102539707D01* -X123560292Y-102428213D01* -X123560288Y-102428210D01* -X123429185Y-102340609D01* -X123429172Y-102340602D01* -X123283501Y-102280264D01* -X123283489Y-102280261D01* -X123128845Y-102249500D01* -X123128842Y-102249500D01* -X122971158Y-102249500D01* -X122971155Y-102249500D01* -X122816510Y-102280261D01* -X122816498Y-102280264D01* -X122670827Y-102340602D01* -X122670814Y-102340609D01* -X122539711Y-102428210D01* -X122539707Y-102428213D01* -X122428213Y-102539707D01* -X122428210Y-102539711D01* -X122340609Y-102670814D01* -X122340602Y-102670827D01* -X122280264Y-102816498D01* -X122280261Y-102816510D01* -X122249500Y-102971153D01* -X122249500Y-103128846D01* -X122280261Y-103283489D01* -X122280264Y-103283501D01* -X122340602Y-103429172D01* -X122340609Y-103429185D01* -X122428210Y-103560288D01* -X122428213Y-103560292D01* -X122539707Y-103671786D01* -X122539711Y-103671789D01* -X122552288Y-103680193D01* -X122597093Y-103733805D01* -X122605800Y-103803130D01* -X122575646Y-103866157D01* -X122552289Y-103886396D01* -X122489713Y-103928208D01* -X122489707Y-103928213D01* -X122378213Y-104039707D01* -X122378210Y-104039711D01* -X122290609Y-104170814D01* -X122290604Y-104170824D01* -X122237059Y-104300094D01* -X122193218Y-104354497D01* -X122146690Y-104374258D01* -X122116508Y-104380261D01* -X122116498Y-104380264D01* -X121970827Y-104440602D01* -X121970814Y-104440609D01* -X121839711Y-104528210D01* -X121839707Y-104528213D01* -X121728213Y-104639707D01* -X121728210Y-104639711D01* -X121640609Y-104770814D01* -X121640602Y-104770827D01* -X121580264Y-104916498D01* -X121580261Y-104916510D01* -X121549500Y-105071153D01* -X120250500Y-105071153D01* -X120250500Y-97940666D01* -X120270185Y-97873627D01* -X120322989Y-97827872D01* -X120392147Y-97817928D01* -X120421951Y-97826105D01* -X120426217Y-97827872D01* -X120455097Y-97839835D01* -X120455099Y-97839835D01* -X120455103Y-97839837D01* -X120519747Y-97852695D01* -X120610449Y-97870738D01* -X120672360Y-97903123D01* -X120673938Y-97904673D01* -X124665984Y-101896720D01* -X124665986Y-101896721D01* -X124665990Y-101896724D01* -X124788841Y-101967651D01* -X124802916Y-101975777D01* -X124955643Y-102016701D01* -X124955645Y-102016701D01* -X125121354Y-102016701D01* -X125121370Y-102016700D01* -X128030003Y-102016700D01* -X128097042Y-102036385D01* -X128117679Y-102053014D01* -X128284632Y-102219968D01* -X128318116Y-102281290D01* -X128313132Y-102350982D01* -X128271260Y-102406915D01* -X128265843Y-102410748D01* -X128239716Y-102428206D01* -X128239707Y-102428213D01* -X128128213Y-102539707D01* -X128128210Y-102539711D01* -X128040609Y-102670814D01* -X128040602Y-102670827D01* -X127980264Y-102816498D01* -X127980261Y-102816510D01* -X127949500Y-102971153D01* -X127949500Y-103128846D01* -X127980261Y-103283489D01* -X127980264Y-103283501D01* -X128040602Y-103429172D01* -X128040609Y-103429185D01* -X128128210Y-103560288D01* -X128128213Y-103560292D01* -X128239707Y-103671786D01* -X128239711Y-103671789D01* -X128370814Y-103759390D01* -X128370827Y-103759397D01* -X128516498Y-103819735D01* -X128516503Y-103819737D01* -X128621418Y-103840606D01* -X128671153Y-103850499D01* -X128671156Y-103850500D01* -X128671158Y-103850500D01* -X128828844Y-103850500D01* -X128828845Y-103850499D01* -X128983497Y-103819737D01* -X129101592Y-103770821D01* -X129129172Y-103759397D01* -X129129172Y-103759396D01* -X129129179Y-103759394D01* -X129260289Y-103671789D01* -X129371789Y-103560289D01* -X129425262Y-103480261D01* -X129438117Y-103461023D01* -X129491729Y-103416217D01* -X129561054Y-103407510D01* -X129624081Y-103437664D01* -X129660801Y-103497107D01* -X129662836Y-103554104D01* -X129649499Y-103621153D01* -X129649499Y-103778846D01* -X129680260Y-103933489D01* -X129680263Y-103933501D01* -X129740601Y-104079172D01* -X129740608Y-104079185D01* -X129828209Y-104210288D01* -X129828212Y-104210292D01* -X129939706Y-104321786D01* -X129939710Y-104321789D01* -X130070813Y-104409390D01* -X130070826Y-104409397D01* -X130186020Y-104457111D01* -X130216502Y-104469737D01* -X130305355Y-104487411D01* -X130371152Y-104500499D01* -X130371155Y-104500500D01* -X130409179Y-104500500D01* -X130476218Y-104520185D01* -X130521973Y-104572989D01* -X130531917Y-104642147D01* -X130512281Y-104693391D01* -X130487809Y-104730014D01* -X130487802Y-104730027D01* -X130427464Y-104875698D01* -X130427461Y-104875710D01* -X130396700Y-105030353D01* -X130396700Y-105188046D01* -X130427461Y-105342689D01* -X130427464Y-105342701D01* -X130487802Y-105488372D01* -X130487809Y-105488385D01* -X130575410Y-105619488D01* -X130575413Y-105619492D01* -X130686907Y-105730986D01* -X130686911Y-105730989D01* -X130818014Y-105818590D01* -X130818027Y-105818597D01* -X130963698Y-105878935D01* -X130963703Y-105878937D01* -X131118353Y-105909699D01* -X131118356Y-105909700D01* -X131118358Y-105909700D01* -X131276044Y-105909700D01* -X131276045Y-105909699D01* -X131430697Y-105878937D01* -X131576379Y-105818594D01* -X131707489Y-105730989D01* -X131818989Y-105619489D01* -X131906594Y-105488379D01* -X131966937Y-105342697D01* -X131997700Y-105188042D01* -X131997700Y-105074500D01* -X132017385Y-105007461D01* -X132070189Y-104961706D01* -X132121700Y-104950500D01* -X132228844Y-104950500D01* -X132228845Y-104950499D01* -X132383497Y-104919737D01* -X132529179Y-104859394D01* -X132660289Y-104771789D01* -X132771789Y-104660289D01* -X132859394Y-104529179D01* -X132919737Y-104383497D01* -X132950500Y-104228842D01* -X132950500Y-104071158D01* -X132950500Y-104071155D01* -X132950499Y-104071153D01* -X132928422Y-103960167D01* -X132919737Y-103916503D01* -X132909484Y-103891750D01* -X132859397Y-103770827D01* -X132859390Y-103770814D01* -X132801354Y-103683957D01* -X132771789Y-103639711D01* -X132771786Y-103639707D01* -X132753232Y-103621153D01* -X133799500Y-103621153D01* -X133799500Y-103778846D01* -X133830261Y-103933489D01* -X133830264Y-103933501D01* -X133890602Y-104079172D01* -X133890609Y-104079185D01* -X133978210Y-104210288D01* -X133978213Y-104210292D01* -X134089707Y-104321786D01* -X134089711Y-104321789D01* -X134220814Y-104409390D01* -X134220827Y-104409397D01* -X134336021Y-104457111D01* -X134366503Y-104469737D01* -X134455356Y-104487411D01* -X134521153Y-104500499D01* -X134521156Y-104500500D01* -X134521158Y-104500500D01* -X134678844Y-104500500D01* -X134678845Y-104500499D01* -X134833497Y-104469737D01* -X134882129Y-104449592D01* -X134951597Y-104442124D01* -X134998472Y-104461052D01* -X135033452Y-104484425D01* -X135070821Y-104509394D01* -X135070823Y-104509395D01* -X135070827Y-104509397D01* -X135216498Y-104569735D01* -X135216503Y-104569737D01* -X135274767Y-104581326D01* -X135377132Y-104601689D01* -X135376650Y-104604107D01* -X135431395Y-104626204D01* -X135457568Y-104654565D01* -X135528210Y-104760288D01* -X135528213Y-104760292D01* -X135639707Y-104871786D01* -X135639711Y-104871789D01* -X135770814Y-104959390D01* -X135770827Y-104959397D01* -X135916498Y-105019735D01* -X135916503Y-105019737D01* -X136071153Y-105050499D01* -X136071156Y-105050500D01* -X136071158Y-105050500D01* -X136228844Y-105050500D01* -X136228845Y-105050499D01* -X136383497Y-105019737D01* -X136529179Y-104959394D01* -X136660289Y-104871789D01* -X136771789Y-104760289D01* -X136859394Y-104629179D01* -X136859395Y-104629176D01* -X136859397Y-104629173D01* -X136891201Y-104552389D01* -X136906149Y-104516300D01* -X136949989Y-104461897D01* -X137016283Y-104439832D01* -X137083983Y-104457111D01* -X137131593Y-104508248D01* -X137135271Y-104516299D01* -X137140606Y-104529179D01* -X137140609Y-104529185D01* -X137228210Y-104660288D01* -X137228213Y-104660292D01* -X137339707Y-104771786D01* -X137339711Y-104771789D01* -X137470814Y-104859390D01* -X137470827Y-104859397D01* -X137608683Y-104916498D01* -X137616503Y-104919737D01* -X137771153Y-104950499D01* -X137771156Y-104950500D01* -X137771158Y-104950500D01* -X137928844Y-104950500D01* -X137928845Y-104950499D01* -X138083497Y-104919737D01* -X138229179Y-104859394D01* -X138360289Y-104771789D01* -X138471789Y-104660289D01* -X138559394Y-104529179D01* -X138577932Y-104484423D01* -X138621772Y-104430021D01* -X138688066Y-104407955D01* -X138739942Y-104417314D01* -X138866503Y-104469737D01* -X138955356Y-104487411D01* -X139021153Y-104500499D01* -X139021156Y-104500500D01* -X139021158Y-104500500D01* -X139178844Y-104500500D01* -X139178845Y-104500499D01* -X139333497Y-104469737D01* -X139479179Y-104409394D01* -X139610289Y-104321789D01* -X139721789Y-104210289D01* -X139809394Y-104079179D01* -X139812719Y-104071153D01* -X139858690Y-103960167D01* -X139869737Y-103933497D01* -X139900500Y-103778842D01* -X139900500Y-103621158D01* -X139900500Y-103621155D01* -X139900499Y-103621153D01* -X139887162Y-103554104D01* -X139869737Y-103466503D01* -X139859606Y-103442044D01* -X139809397Y-103320827D01* -X139809390Y-103320814D01* -X139721789Y-103189711D01* -X139721786Y-103189707D01* -X139610289Y-103078210D01* -X139595259Y-103068168D01* -X139479185Y-102990609D01* -X139479172Y-102990602D01* -X139432217Y-102971153D01* -X141999500Y-102971153D01* -X141999500Y-103128846D01* -X142030261Y-103283489D01* -X142030264Y-103283501D01* -X142090602Y-103429172D01* -X142090609Y-103429185D01* -X142178210Y-103560288D01* -X142178213Y-103560292D01* -X142289707Y-103671786D01* -X142289711Y-103671789D01* -X142420814Y-103759390D01* -X142420827Y-103759397D01* -X142566498Y-103819735D01* -X142566503Y-103819737D01* -X142671418Y-103840606D01* -X142721153Y-103850499D01* -X142721156Y-103850500D01* -X142721158Y-103850500D01* -X142878844Y-103850500D01* -X142878845Y-103850499D01* -X143033497Y-103819737D01* -X143151592Y-103770821D01* -X143179172Y-103759397D01* -X143179172Y-103759396D01* -X143179179Y-103759394D01* -X143310289Y-103671789D01* -X143421789Y-103560289D01* -X143509394Y-103429179D01* -X143569737Y-103283497D01* -X143584719Y-103208177D01* -X143595560Y-103153680D01* -X143627945Y-103091769D01* -X143669721Y-103063311D01* -X143679179Y-103059394D01* -X143810289Y-102971789D01* -X143810925Y-102971153D01* -X144599500Y-102971153D01* -X144599500Y-103128846D01* -X144630261Y-103283489D01* -X144630264Y-103283501D01* -X144690602Y-103429172D01* -X144690609Y-103429185D01* -X144778210Y-103560288D01* -X144778213Y-103560292D01* -X144889707Y-103671786D01* -X144889711Y-103671789D01* -X145020814Y-103759390D01* -X145020827Y-103759397D01* -X145166498Y-103819735D01* -X145166503Y-103819737D01* -X145271418Y-103840606D01* -X145321153Y-103850499D01* -X145321156Y-103850500D01* -X145321158Y-103850500D01* -X145478844Y-103850500D01* -X145478845Y-103850499D01* -X145633497Y-103819737D01* -X145751592Y-103770821D01* -X145779172Y-103759397D01* -X145779172Y-103759396D01* -X145779179Y-103759394D01* -X145910289Y-103671789D01* -X146021789Y-103560289D01* -X146109394Y-103429179D01* -X146169737Y-103283497D01* -X146200500Y-103128842D01* -X146200500Y-102971158D01* -X146200500Y-102971155D01* -X146200499Y-102971153D01* -X146178447Y-102860292D01* -X146169737Y-102816503D01* -X146133569Y-102729185D01* -X146109397Y-102670827D01* -X146109390Y-102670814D01* -X146021789Y-102539711D01* -X146021786Y-102539707D01* -X145910292Y-102428213D01* -X145910288Y-102428210D01* -X145779185Y-102340609D01* -X145779172Y-102340602D01* -X145633501Y-102280264D01* -X145633489Y-102280261D01* -X145478845Y-102249500D01* -X145478842Y-102249500D01* -X145321158Y-102249500D01* -X145321155Y-102249500D01* -X145166510Y-102280261D01* -X145166498Y-102280264D01* -X145020827Y-102340602D01* -X145020814Y-102340609D01* -X144889711Y-102428210D01* -X144889707Y-102428213D01* -X144778213Y-102539707D01* -X144778210Y-102539711D01* -X144690609Y-102670814D01* -X144690602Y-102670827D01* -X144630264Y-102816498D01* -X144630261Y-102816510D01* -X144599500Y-102971153D01* -X143810925Y-102971153D01* -X143851817Y-102930261D01* -X143904694Y-102877385D01* -X143921786Y-102860292D01* -X143921789Y-102860289D01* -X144009394Y-102729179D01* -X144069737Y-102583497D01* -X144100500Y-102428842D01* -X144100500Y-102271158D01* -X144100500Y-102271155D01* -X144100499Y-102271153D01* -X144069738Y-102116510D01* -X144069738Y-102116508D01* -X144069737Y-102116503D01* -X144069735Y-102116498D01* -X144009397Y-101970827D01* -X144009390Y-101970814D01* -X143921789Y-101839711D01* -X143921786Y-101839707D01* -X143810292Y-101728213D01* -X143810288Y-101728210D01* -X143679185Y-101640609D01* -X143679172Y-101640602D01* -X143533501Y-101580264D01* -X143533489Y-101580261D01* -X143378845Y-101549500D01* -X143378842Y-101549500D01* -X143221158Y-101549500D01* -X143221155Y-101549500D01* -X143066510Y-101580261D01* -X143066498Y-101580264D01* -X142920827Y-101640602D01* -X142920814Y-101640609D01* -X142789711Y-101728210D01* -X142789707Y-101728213D01* -X142678213Y-101839707D01* -X142678210Y-101839711D01* -X142590609Y-101970814D01* -X142590602Y-101970827D01* -X142530264Y-102116498D01* -X142530261Y-102116508D01* -X142504440Y-102246320D01* -X142472055Y-102308231D01* -X142430278Y-102336688D01* -X142420826Y-102340603D01* -X142420814Y-102340609D01* -X142289711Y-102428210D01* -X142289707Y-102428213D01* -X142178213Y-102539707D01* -X142178210Y-102539711D01* -X142090609Y-102670814D01* -X142090602Y-102670827D01* -X142030264Y-102816498D01* -X142030261Y-102816510D01* -X141999500Y-102971153D01* -X139432217Y-102971153D01* -X139333501Y-102930264D01* -X139333489Y-102930261D01* -X139178845Y-102899500D01* -X139178842Y-102899500D01* -X139021158Y-102899500D01* -X139021155Y-102899500D01* -X138866510Y-102930261D01* -X138866498Y-102930264D01* -X138720827Y-102990602D01* -X138720814Y-102990609D01* -X138589711Y-103078210D01* -X138589707Y-103078213D01* -X138478213Y-103189707D01* -X138478210Y-103189711D01* -X138390609Y-103320814D01* -X138390606Y-103320821D01* -X138372067Y-103365577D01* -X138328225Y-103419980D01* -X138261930Y-103442044D01* -X138210054Y-103432684D01* -X138083501Y-103380264D01* -X138083489Y-103380261D01* -X137928845Y-103349500D01* -X137928842Y-103349500D01* -X137771158Y-103349500D01* -X137771155Y-103349500D01* -X137616510Y-103380261D01* -X137616498Y-103380264D01* -X137470827Y-103440602D01* -X137470814Y-103440609D01* -X137339711Y-103528210D01* -X137339707Y-103528213D01* -X137228213Y-103639707D01* -X137228210Y-103639711D01* -X137140609Y-103770814D01* -X137140604Y-103770824D01* -X137093850Y-103883699D01* -X137050009Y-103938102D01* -X136983715Y-103960167D01* -X136916015Y-103942888D01* -X136868405Y-103891750D01* -X136864727Y-103883696D01* -X136859395Y-103870824D01* -X136859394Y-103870821D01* -X136859392Y-103870818D01* -X136859390Y-103870814D01* -X136771789Y-103739711D01* -X136771786Y-103739707D01* -X136660292Y-103628213D01* -X136660288Y-103628210D01* -X136529185Y-103540609D01* -X136529172Y-103540602D01* -X136383501Y-103480264D01* -X136383489Y-103480261D01* -X136222868Y-103448311D01* -X136223346Y-103445906D01* -X136168547Y-103423750D01* -X136142431Y-103395434D01* -X136071789Y-103289710D01* -X135960292Y-103178213D01* -X135960287Y-103178209D01* -X135829185Y-103090609D01* -X135829172Y-103090602D01* -X135683501Y-103030264D01* -X135683489Y-103030261D01* -X135528845Y-102999500D01* -X135528842Y-102999500D01* -X135371158Y-102999500D01* -X135371155Y-102999500D01* -X135216505Y-103030261D01* -X135167870Y-103050407D01* -X135098400Y-103057875D01* -X135051527Y-103038947D01* -X134979185Y-102990609D01* -X134979172Y-102990602D01* -X134833501Y-102930264D01* -X134833489Y-102930261D01* -X134678845Y-102899500D01* -X134678842Y-102899500D01* -X134521158Y-102899500D01* -X134521155Y-102899500D01* -X134366510Y-102930261D01* -X134366498Y-102930264D01* -X134220827Y-102990602D01* -X134220814Y-102990609D01* -X134089711Y-103078210D01* -X134089707Y-103078213D01* -X133978213Y-103189707D01* -X133978210Y-103189711D01* -X133890609Y-103320814D01* -X133890602Y-103320827D01* -X133830264Y-103466498D01* -X133830261Y-103466510D01* -X133799500Y-103621153D01* -X132753232Y-103621153D01* -X132660292Y-103528213D01* -X132660288Y-103528210D01* -X132529185Y-103440609D01* -X132529172Y-103440602D01* -X132383501Y-103380264D01* -X132383489Y-103380261D01* -X132228845Y-103349500D01* -X132228842Y-103349500D01* -X132071158Y-103349500D01* -X132071155Y-103349500D01* -X131916510Y-103380261D01* -X131916498Y-103380264D01* -X131770827Y-103440602D01* -X131770814Y-103440609D01* -X131639711Y-103528210D01* -X131639707Y-103528213D01* -X131528213Y-103639707D01* -X131528210Y-103639711D01* -X131477601Y-103715453D01* -X131423989Y-103760258D01* -X131354664Y-103768965D01* -X131291636Y-103738810D01* -X131254917Y-103679367D01* -X131250499Y-103646562D01* -X131250499Y-103621155D01* -X131250498Y-103621153D01* -X131237161Y-103554104D01* -X131219736Y-103466503D01* -X131177285Y-103364018D01* -X131169817Y-103294550D01* -X131201092Y-103232071D01* -X131229848Y-103209179D01* -X131231582Y-103208177D01* -X131231585Y-103208177D01* -X131283487Y-103178211D01* -X131368516Y-103129120D01* -X131480320Y-103017316D01* -X131480320Y-103017314D01* -X131490524Y-103007111D01* -X131490527Y-103007106D01* -X133565494Y-100932141D01* -X133626814Y-100898658D01* -X133696506Y-100903642D01* -X133752439Y-100945514D01* -X133776856Y-101010978D01* -X133774789Y-101044015D01* -X133749500Y-101171153D01* -X133749500Y-101328846D01* -X133780261Y-101483489D01* -X133780264Y-101483501D01* -X133840602Y-101629172D01* -X133840609Y-101629185D01* -X133928210Y-101760288D01* -X133928213Y-101760292D01* -X134039707Y-101871786D01* -X134039711Y-101871789D01* -X134170814Y-101959390D01* -X134170827Y-101959397D01* -X134309171Y-102016700D01* -X134316503Y-102019737D01* -X134471153Y-102050499D01* -X134471156Y-102050500D01* -X134471158Y-102050500D01* -X134628844Y-102050500D01* -X134628845Y-102050499D01* -X134783497Y-102019737D01* -X134901592Y-101970821D01* -X134929172Y-101959397D01* -X134929172Y-101959396D01* -X134929179Y-101959394D01* -X135060289Y-101871789D01* -X135171789Y-101760289D01* -X135193222Y-101728213D01* -X135196898Y-101722712D01* -X135250510Y-101677906D01* -X135319835Y-101669199D01* -X135382862Y-101699353D01* -X135403102Y-101722712D01* -X135428207Y-101760284D01* -X135428213Y-101760292D01* -X135539707Y-101871786D01* -X135539711Y-101871789D01* -X135670814Y-101959390D01* -X135670827Y-101959397D01* -X135809171Y-102016700D01* -X135816503Y-102019737D01* -X135971153Y-102050499D01* -X135971156Y-102050500D01* -X135971158Y-102050500D01* -X136128844Y-102050500D01* -X136128845Y-102050499D01* -X136283497Y-102019737D01* -X136401592Y-101970821D01* -X136429172Y-101959397D01* -X136429172Y-101959396D01* -X136429179Y-101959394D01* -X136560289Y-101871789D01* -X136671789Y-101760289D01* -X136759394Y-101629179D01* -X136819737Y-101483497D01* -X136850500Y-101328842D01* -X136850500Y-101171158D01* -X136850500Y-101171155D01* -X136847453Y-101155841D01* -X136853677Y-101086250D01* -X136896538Y-101031070D01* -X136900127Y-101028578D01* -X136910289Y-101021789D01* -X137021789Y-100910289D01* -X137109394Y-100779179D01* -X137169737Y-100633497D01* -X137200500Y-100478842D01* -X137200500Y-100321158D01* -X137200500Y-100321155D01* -X137184017Y-100238292D01* -X137190244Y-100168700D01* -X137233107Y-100113523D01* -X137298996Y-100090278D01* -X137305634Y-100090100D01* -X138284800Y-100090100D01* -X138351839Y-100109785D01* -X138397594Y-100162589D01* -X138408800Y-100214100D01* -X138408800Y-100263146D01* -X138439561Y-100417789D01* -X138439564Y-100417801D01* -X138499902Y-100563472D01* -X138499909Y-100563485D01* -X138587510Y-100694588D01* -X138587513Y-100694592D01* -X138699007Y-100806086D01* -X138699011Y-100806089D01* -X138830114Y-100893690D01* -X138830127Y-100893697D01* -X138975798Y-100954035D01* -X138975803Y-100954037D01* -X139130453Y-100984799D01* -X139130456Y-100984800D01* -X139130458Y-100984800D01* -X139288144Y-100984800D01* -X139288145Y-100984799D01* -X139442797Y-100954037D01* -X139588479Y-100893694D01* -X139719589Y-100806089D01* -X139831089Y-100694589D01* -X139918694Y-100563479D01* -X139979037Y-100417797D01* -X140009800Y-100263142D01* -X140009800Y-100214100D01* -X140029485Y-100147061D01* -X140082289Y-100101306D01* -X140133800Y-100090100D01* -X143921631Y-100090100D01* -X143921647Y-100090101D01* -X143929243Y-100090101D01* -X144087354Y-100090101D01* -X144087357Y-100090101D01* -X144240085Y-100049177D01* -X144322097Y-100001827D01* -X144377016Y-99970120D01* -X144488820Y-99858316D01* -X144488820Y-99858314D01* -X144499024Y-99848111D01* -X144499027Y-99848106D01* -X145467562Y-98879572D01* -X145528883Y-98846089D01* -X145531050Y-98845638D01* -X145588985Y-98834113D01* -X145686397Y-98814737D01* -X145832079Y-98754394D01* -X145963189Y-98666789D01* -X145963192Y-98666786D01* -X146033991Y-98595988D01* -X146095314Y-98562503D01* -X146165006Y-98567487D01* -X146209353Y-98595988D01* -X147775681Y-100162316D01* -X147809166Y-100223639D01* -X147812000Y-100249997D01* -X147812000Y-101454729D01* -X147792315Y-101521768D01* -X147739511Y-101567523D01* -X147670353Y-101577467D01* -X147663809Y-101576346D01* -X147528845Y-101549500D01* -X147528842Y-101549500D01* -X147371158Y-101549500D01* -X147371155Y-101549500D01* -X147216510Y-101580261D01* -X147216498Y-101580264D01* -X147070827Y-101640602D01* -X147070814Y-101640609D01* -X146939711Y-101728210D01* -X146939707Y-101728213D01* -X146828213Y-101839707D01* -X146828210Y-101839711D01* -X146740609Y-101970814D01* -X146740602Y-101970827D01* -X146680264Y-102116498D01* -X146680261Y-102116510D01* -X146649500Y-102271153D01* -X146649500Y-102428846D01* -X146680261Y-102583489D01* -X146680264Y-102583501D01* -X146740602Y-102729172D01* -X146740609Y-102729185D01* -X146828210Y-102860288D01* -X146828213Y-102860292D01* -X146939707Y-102971786D01* -X146939711Y-102971789D01* -X147070814Y-103059390D01* -X147070827Y-103059397D01* -X147149498Y-103091983D01* -X147216503Y-103119737D01* -X147371153Y-103150499D01* -X147371156Y-103150500D01* -X147371158Y-103150500D01* -X147528844Y-103150500D01* -X147595140Y-103137312D01* -X147663809Y-103123653D01* -X147733400Y-103129880D01* -X147788577Y-103172742D01* -X147811822Y-103238632D01* -X147812000Y-103245270D01* -X147812000Y-105554729D01* -X147792315Y-105621768D01* -X147739511Y-105667523D01* -X147670353Y-105677467D01* -X147663809Y-105676346D01* -X147528845Y-105649500D01* -X147528842Y-105649500D01* -X147371158Y-105649500D01* -X147371155Y-105649500D01* -X147216510Y-105680261D01* -X147216498Y-105680264D01* -X147070827Y-105740602D01* -X147070814Y-105740609D01* -X146939711Y-105828210D01* -X146939707Y-105828213D01* -X146828213Y-105939707D01* -X146828210Y-105939711D01* -X146740609Y-106070814D01* -X146740602Y-106070827D01* -X146680264Y-106216498D01* -X146680261Y-106216510D01* -X146649500Y-106371153D01* -X146649500Y-106528846D01* -X146680261Y-106683489D01* -X146680264Y-106683501D01* -X146740602Y-106829172D01* -X146740609Y-106829185D01* -X146828210Y-106960288D01* -X146828213Y-106960292D01* -X146939707Y-107071786D01* -X146939711Y-107071789D01* -X147070814Y-107159390D01* -X147070827Y-107159397D01* -X147216498Y-107219735D01* -X147216503Y-107219737D01* -X147341065Y-107244514D01* -X147371153Y-107250499D01* -X147371156Y-107250500D01* -X147371158Y-107250500D01* -X147528844Y-107250500D01* -X147595140Y-107237312D01* -X147663809Y-107223653D01* -X147733400Y-107229880D01* -X147788577Y-107272742D01* -X147811822Y-107338632D01* -X147812000Y-107345270D01* -X147812000Y-108907621D01* -X147792315Y-108974660D01* -X147739511Y-109020415D01* -X147670353Y-109030359D01* -X147640548Y-109022182D01* -X147533549Y-108977862D01* -X147533542Y-108977860D01* -X147533540Y-108977859D01* -X147533534Y-108977858D01* -X147389459Y-108949200D01* -X147389455Y-108949200D01* -X147242545Y-108949200D01* -X147242540Y-108949200D01* -X147098465Y-108977858D01* -X147098455Y-108977861D01* -X146962733Y-109034078D01* -X146962724Y-109034083D01* -X146840580Y-109115698D01* -X146840576Y-109115701D01* -X146736701Y-109219576D01* -X146736698Y-109219580D01* -X146655083Y-109341724D01* -X146655078Y-109341733D01* -X146598861Y-109477455D01* -X146598858Y-109477465D01* -X146570200Y-109621540D01* -X146570200Y-109768459D01* -X146598858Y-109912534D01* -X146598861Y-109912544D01* -X146655078Y-110048266D01* -X146655083Y-110048275D01* -X146736698Y-110170419D01* -X146736701Y-110170423D01* -X146840576Y-110274298D01* -X146840580Y-110274301D01* -X146962724Y-110355916D01* -X146962733Y-110355921D01* -X146987800Y-110366304D01* -X147098458Y-110412140D01* -X147242540Y-110440799D01* -X147242544Y-110440800D01* -X147242545Y-110440800D01* -X147389456Y-110440800D01* -X147389457Y-110440799D01* -X147533542Y-110412140D01* -X147640547Y-110367816D01* -X147710017Y-110360348D01* -X147772496Y-110391623D01* -X147808148Y-110451712D01* -X147812000Y-110482378D01* -X147812000Y-111000968D01* -X147792315Y-111068007D01* -X147739511Y-111113762D01* -X147735455Y-111115528D01* -X147693026Y-111133103D01* -X147693014Y-111133109D01* -X147561911Y-111220710D01* -X147561907Y-111220713D01* -X147450413Y-111332207D01* -X147450410Y-111332211D01* -X147362809Y-111463314D01* -X147362802Y-111463327D01* -X147302464Y-111608998D01* -X147302461Y-111609010D01* -X147271700Y-111763653D01* -X147271700Y-111921346D01* -X147302461Y-112075989D01* -X147302464Y-112076001D01* -X147362802Y-112221672D01* -X147362809Y-112221685D01* -X147450410Y-112352788D01* -X147450413Y-112352792D01* -X147561907Y-112464286D01* -X147561911Y-112464289D01* -X147693014Y-112551890D01* -X147693027Y-112551897D01* -X147838698Y-112612235D01* -X147838703Y-112612237D01* -X147993353Y-112642999D01* -X147993356Y-112643000D01* -X147993358Y-112643000D01* -X148151044Y-112643000D01* -X148151045Y-112642999D01* -X148305697Y-112612237D01* -X148451379Y-112551894D01* -X148582489Y-112464289D01* -X148693989Y-112352789D01* -X148781594Y-112221679D01* -X148841937Y-112075997D01* -X148872700Y-111921342D01* -X148872700Y-111921341D01* -X148873489Y-111917375D01* -X148890861Y-111879054D01* -X148888956Y-111877955D01* -X148893020Y-111870916D01* -X148955069Y-111763443D01* -X148972077Y-111733985D01* -X149013001Y-111581257D01* -X149013001Y-111423143D01* -X149013001Y-111415548D01* -X149013000Y-111415530D01* -X149013000Y-100038960D01* -X149013001Y-100038947D01* -X149013001Y-99870844D01* -X149009644Y-99858316D01* -X148972077Y-99718116D01* -X148921356Y-99630263D01* -X148893024Y-99581190D01* -X148893018Y-99581182D01* -X147867125Y-98555289D01* -X146825815Y-97513980D01* -X146792331Y-97452658D01* -X146797315Y-97382966D01* -X146839187Y-97327033D01* -X146904651Y-97302616D01* -X146913497Y-97302300D01* -X148793384Y-97302300D01* -X148840836Y-97311739D01* +X120250500Y-120611152D01* +X129379498Y-120611152D01* +X129379498Y-120768845D01* +X129410259Y-120923488D01* +X129410262Y-120923500D01* +X129470600Y-121069171D01* +X129470607Y-121069184D01* +X129558208Y-121200287D01* +X129558211Y-121200291D01* +X129669705Y-121311785D01* +X129669709Y-121311788D01* +X129800812Y-121399389D01* +X129800825Y-121399396D01* +X129946496Y-121459734D01* +X129946501Y-121459736D01* +X130101151Y-121490498D01* +X130101154Y-121490499D01* +X130101156Y-121490499D01* +X130258842Y-121490499D01* +X130258843Y-121490498D01* +X130413495Y-121459736D01* +X130559177Y-121399393D01* +X130690287Y-121311788D01* +X130801787Y-121200288D01* +X130889392Y-121069178D01* +X130949735Y-120923496D01* +X130980498Y-120768841D01* +X130980498Y-120611157D01* +X130980498Y-120611154D01* +X130980497Y-120611152D01* +X130949736Y-120456509D01* +X130949735Y-120456502D01* +X130949733Y-120456497D01* +X130889395Y-120310826D01* +X130889388Y-120310813D01* +X130801787Y-120179710D01* +X130801784Y-120179706D01* +X130690290Y-120068212D01* +X130690286Y-120068209D01* +X130559183Y-119980608D01* +X130559170Y-119980601D01* +X130413499Y-119920263D01* +X130413487Y-119920260D01* +X130258843Y-119889499D01* +X130258840Y-119889499D01* +X130101156Y-119889499D01* +X130101153Y-119889499D01* +X129946508Y-119920260D01* +X129946496Y-119920263D01* +X129800825Y-119980601D01* +X129800812Y-119980608D01* +X129669709Y-120068209D01* +X129669705Y-120068212D01* +X129558211Y-120179706D01* +X129558208Y-120179710D01* +X129470607Y-120310813D01* +X129470600Y-120310826D01* +X129410262Y-120456497D01* +X129410259Y-120456509D01* +X129379498Y-120611152D01* +X120250500Y-120611152D01* +X120250500Y-119521153D01* +X123199500Y-119521153D01* +X123199500Y-119678846D01* +X123230261Y-119833489D01* +X123230264Y-119833501D01* +X123290602Y-119979172D01* +X123290609Y-119979185D01* +X123378210Y-120110288D01* +X123378213Y-120110292D01* +X123489707Y-120221786D01* +X123489711Y-120221789D01* +X123620814Y-120309390D01* +X123620827Y-120309397D01* +X123766498Y-120369735D01* +X123766503Y-120369737D01* +X123921153Y-120400499D01* +X123921156Y-120400500D01* +X123921158Y-120400500D01* +X124078844Y-120400500D01* +X124078845Y-120400499D01* +X124233497Y-120369737D01* +X124375722Y-120310826D01* +X124379172Y-120309397D01* +X124379172Y-120309396D01* +X124379179Y-120309394D01* +X124510289Y-120221789D01* +X124621789Y-120110289D01* +X124709394Y-119979179D01* +X124769737Y-119833497D01* +X124800500Y-119678842D01* +X124800500Y-119521158D01* +X124800500Y-119521155D01* +X124800499Y-119521153D01* +X124778269Y-119409397D01* +X124769737Y-119366503D01* +X124744284Y-119305053D01* +X124709397Y-119220827D01* +X124709390Y-119220814D01* +X124621789Y-119089711D01* +X124621786Y-119089707D01* +X124510292Y-118978213D01* +X124510288Y-118978210D01* +X124379185Y-118890609D01* +X124379172Y-118890602D01* +X124233501Y-118830264D01* +X124233489Y-118830261D01* +X124078845Y-118799500D01* +X124078842Y-118799500D01* +X123921158Y-118799500D01* +X123921155Y-118799500D01* +X123766510Y-118830261D01* +X123766498Y-118830264D01* +X123620827Y-118890602D01* +X123620814Y-118890609D01* +X123489711Y-118978210D01* +X123489707Y-118978213D01* +X123378213Y-119089707D01* +X123378210Y-119089711D01* +X123290609Y-119220814D01* +X123290602Y-119220827D01* +X123230264Y-119366498D01* +X123230261Y-119366510D01* +X123199500Y-119521153D01* +X120250500Y-119521153D01* +X120250500Y-117721153D01* +X126999500Y-117721153D01* +X126999500Y-117878846D01* +X127030261Y-118033489D01* +X127030264Y-118033501D01* +X127090602Y-118179172D01* +X127090609Y-118179185D01* +X127178210Y-118310288D01* +X127178213Y-118310292D01* +X127289707Y-118421786D01* +X127289711Y-118421789D01* +X127420814Y-118509390D01* +X127420827Y-118509397D01* +X127561394Y-118567621D01* +X127566503Y-118569737D01* +X127721153Y-118600499D01* +X127721156Y-118600500D01* +X127721158Y-118600500D01* +X127878844Y-118600500D01* +X127878845Y-118600499D01* +X128033497Y-118569737D01* +X128179179Y-118509394D01* +X128310289Y-118421789D01* +X128421789Y-118310289D01* +X128509394Y-118179179D01* +X128569737Y-118033497D01* +X128600500Y-117878842D01* +X128600500Y-117721158D01* +X128600500Y-117721155D01* +X128600499Y-117721153D01* +X128583061Y-117633489D01* +X128569737Y-117566503D01* +X128557901Y-117537927D01* +X128509397Y-117420827D01* +X128509390Y-117420814D01* +X128421789Y-117289711D01* +X128421786Y-117289707D01* +X128310292Y-117178213D01* +X128310288Y-117178210D01* +X128179185Y-117090609D01* +X128179172Y-117090602D01* +X128033501Y-117030264D01* +X128033489Y-117030261D01* +X127878845Y-116999500D01* +X127878842Y-116999500D01* +X127721158Y-116999500D01* +X127721155Y-116999500D01* +X127566510Y-117030261D01* +X127566498Y-117030264D01* +X127420827Y-117090602D01* +X127420814Y-117090609D01* +X127289711Y-117178210D01* +X127289707Y-117178213D01* +X127178213Y-117289707D01* +X127178210Y-117289711D01* +X127090609Y-117420814D01* +X127090602Y-117420827D01* +X127030264Y-117566498D01* +X127030261Y-117566510D01* +X126999500Y-117721153D01* +X120250500Y-117721153D01* +X120250500Y-116521153D01* +X129499500Y-116521153D01* +X129499500Y-116678846D01* +X129530261Y-116833489D01* +X129530264Y-116833501D01* +X129590604Y-116979176D01* +X129626162Y-117032392D01* +X129647040Y-117099069D01* +X129637623Y-117148732D01* +X129630262Y-117166502D01* +X129630261Y-117166505D01* +X129599500Y-117321153D01* +X129599500Y-117478846D01* +X129630261Y-117633489D01* +X129630264Y-117633501D01* +X129690602Y-117779172D01* +X129690609Y-117779185D01* +X129778210Y-117910288D01* +X129778213Y-117910292D01* +X129889707Y-118021786D01* +X129889711Y-118021789D01* +X130020814Y-118109390D01* +X130020827Y-118109397D01* +X130166498Y-118169735D01* +X130166503Y-118169737D01* +X130321153Y-118200499D01* +X130321156Y-118200500D01* +X130321158Y-118200500D01* +X130478844Y-118200500D01* +X130492617Y-118197759D01* +X130508802Y-118194540D01* +X130578393Y-118200764D01* +X130633572Y-118243625D01* +X130636099Y-118247265D01* +X130678209Y-118310287D01* +X130678210Y-118310288D01* +X130678211Y-118310289D01* +X130778318Y-118410396D01* +X130811802Y-118471717D01* +X130814636Y-118498076D01* +X130814636Y-118614164D01* +X130845397Y-118768807D01* +X130845400Y-118768819D01* +X130905738Y-118914490D01* +X130905745Y-118914503D01* +X130993346Y-119045606D01* +X130993349Y-119045610D01* +X131104843Y-119157104D01* +X131104847Y-119157107D01* +X131235950Y-119244708D01* +X131235963Y-119244715D01* +X131381634Y-119305053D01* +X131381639Y-119305055D01* +X131536289Y-119335817D01* +X131536292Y-119335818D01* +X131536294Y-119335818D01* +X131693980Y-119335818D01* +X131693981Y-119335817D01* +X131848633Y-119305055D01* +X131994315Y-119244712D01* +X132125425Y-119157107D01* +X132236925Y-119045607D01* +X132324530Y-118914497D01* +X132332591Y-118895034D01* +X132376431Y-118840631D01* +X132442725Y-118818565D01* +X132510425Y-118835843D01* +X132516039Y-118839381D01* +X132620821Y-118909394D01* +X132620823Y-118909395D01* +X132620827Y-118909397D01* +X132747998Y-118962072D01* +X132766503Y-118969737D01* +X132854426Y-118987226D01* +X132921153Y-119000499D01* +X132921156Y-119000500D01* +X132921158Y-119000500D01* +X133078844Y-119000500D01* +X133078845Y-119000499D01* +X133233497Y-118969737D01* +X133379179Y-118909394D01* +X133381110Y-118908103D01* +X133382276Y-118907737D01* +X133384546Y-118906525D01* +X133384776Y-118906955D01* +X133447786Y-118887226D01* +X133515166Y-118905710D01* +X133518850Y-118908077D01* +X133520821Y-118909394D01* +X133520824Y-118909395D01* +X133520827Y-118909397D01* +X133647998Y-118962072D01* +X133666503Y-118969737D01* +X133754426Y-118987226D01* +X133821153Y-119000499D01* +X133821156Y-119000500D01* +X133821158Y-119000500D01* +X133978844Y-119000500D01* +X133978845Y-119000499D01* +X134133497Y-118969737D01* +X134279179Y-118909394D01* +X134410289Y-118821789D01* +X134521789Y-118710289D01* +X134609394Y-118579179D01* +X134610277Y-118577048D01* +X134611035Y-118576106D01* +X134612264Y-118573809D01* +X134612699Y-118574041D01* +X134654115Y-118522646D01* +X134720408Y-118500579D01* +X134724838Y-118500500D01* +X134733741Y-118500500D01* +X134800780Y-118520185D01* +X134846535Y-118572989D01* +X134848302Y-118577048D01* +X134890602Y-118679172D01* +X134890609Y-118679185D01* +X134978210Y-118810288D01* +X134978213Y-118810292D01* +X135089707Y-118921786D01* +X135089711Y-118921789D01* +X135220814Y-119009390D01* +X135220827Y-119009397D01* +X135366498Y-119069735D01* +X135366503Y-119069737D01* +X135521153Y-119100499D01* +X135521156Y-119100500D01* +X135521158Y-119100500D01* +X135678844Y-119100500D01* +X135678845Y-119100499D01* +X135833497Y-119069737D01* +X135979179Y-119009394D01* +X135981110Y-119008103D01* +X135982276Y-119007737D01* +X135984546Y-119006525D01* +X135984776Y-119006955D01* +X136047786Y-118987226D01* +X136115166Y-119005710D01* +X136118850Y-119008077D01* +X136120821Y-119009394D01* +X136120824Y-119009395D01* +X136120827Y-119009397D01* +X136266498Y-119069735D01* +X136266503Y-119069737D01* +X136421153Y-119100499D01* +X136421156Y-119100500D01* +X136421158Y-119100500D01* +X136578844Y-119100500D01* +X136578845Y-119100499D01* +X136733497Y-119069737D01* +X136879179Y-119009394D01* +X137010289Y-118921789D01* +X137121789Y-118810289D01* +X137209394Y-118679179D01* +X137233429Y-118621153D01* +X139799500Y-118621153D01* +X139799500Y-118778846D01* +X139830261Y-118933489D01* +X139830264Y-118933501D01* +X139890602Y-119079172D01* +X139890609Y-119079185D01* +X139978210Y-119210288D01* +X139978213Y-119210292D01* +X140089707Y-119321786D01* +X140089711Y-119321789D01* +X140220814Y-119409390D01* +X140220827Y-119409397D01* +X140366498Y-119469735D01* +X140366503Y-119469737D01* +X140521153Y-119500499D01* +X140521156Y-119500500D01* +X140521158Y-119500500D01* +X140678844Y-119500500D01* +X140678845Y-119500499D01* +X140833497Y-119469737D01* +X140979179Y-119409394D01* +X141110289Y-119321789D01* +X141221789Y-119210289D01* +X141309394Y-119079179D01* +X141369737Y-118933497D01* +X141400500Y-118778842D01* +X141400500Y-118621158D01* +X141400500Y-118621155D01* +X141400499Y-118621153D01* +X141392150Y-118579179D01* +X141369737Y-118466503D01* +X141333427Y-118378842D01* +X141309397Y-118320827D01* +X141309390Y-118320814D01* +X141221789Y-118189711D01* +X141221786Y-118189707D01* +X141110292Y-118078213D01* +X141110288Y-118078210D01* +X140979185Y-117990609D01* +X140979172Y-117990602D01* +X140833501Y-117930264D01* +X140833489Y-117930261D01* +X140678845Y-117899500D01* +X140678842Y-117899500D01* +X140521158Y-117899500D01* +X140521155Y-117899500D01* +X140366510Y-117930261D01* +X140366498Y-117930264D01* +X140220827Y-117990602D01* +X140220814Y-117990609D01* +X140089711Y-118078210D01* +X140089707Y-118078213D01* +X139978213Y-118189707D01* +X139978210Y-118189711D01* +X139890609Y-118320814D01* +X139890602Y-118320827D01* +X139830264Y-118466498D01* +X139830261Y-118466510D01* +X139799500Y-118621153D01* +X137233429Y-118621153D01* +X137250815Y-118579180D01* +X137255603Y-118567621D01* +X137255605Y-118567614D01* +X137269737Y-118533497D01* +X137300500Y-118378842D01* +X137300500Y-118221158D01* +X137300500Y-118221155D01* +X137300499Y-118221153D01* +X137278269Y-118109397D01* +X137269737Y-118066503D01* +X137251215Y-118021786D01* +X137209397Y-117920827D01* +X137209390Y-117920814D01* +X137121789Y-117789711D01* +X137121786Y-117789707D01* +X137010292Y-117678213D01* +X137010288Y-117678210D01* +X136879185Y-117590609D01* +X136879172Y-117590602D01* +X136733501Y-117530264D01* +X136733489Y-117530261D01* +X136578845Y-117499500D01* +X136578842Y-117499500D01* +X136421158Y-117499500D01* +X136421155Y-117499500D01* +X136266510Y-117530261D01* +X136266498Y-117530264D01* +X136120822Y-117590604D01* +X136120820Y-117590605D01* +X136118885Y-117591899D01* +X136117717Y-117592264D01* +X136115451Y-117593476D01* +X136115221Y-117593045D01* +X136052206Y-117612773D01* +X135984827Y-117594285D01* +X135981115Y-117591899D01* +X135979179Y-117590605D01* +X135979177Y-117590604D01* +X135833501Y-117530264D01* +X135833489Y-117530261D01* +X135678845Y-117499500D01* +X135678842Y-117499500D01* +X135566259Y-117499500D01* +X135499220Y-117479815D01* +X135453465Y-117427011D01* +X135451698Y-117422952D01* +X135409397Y-117320827D01* +X135409390Y-117320814D01* +X135321789Y-117189711D01* +X135321786Y-117189707D01* +X135210292Y-117078213D01* +X135210288Y-117078210D01* +X135079185Y-116990609D01* +X135079172Y-116990602D01* +X134933501Y-116930264D01* +X134933489Y-116930261D01* +X134778845Y-116899500D01* +X134778842Y-116899500D01* +X134621158Y-116899500D01* +X134621155Y-116899500D01* +X134466510Y-116930261D01* +X134466498Y-116930264D01* +X134320827Y-116990602D01* +X134320814Y-116990609D01* +X134189711Y-117078210D01* +X134189707Y-117078213D01* +X134078213Y-117189707D01* +X134078210Y-117189711D01* +X133990609Y-117320814D01* +X133990607Y-117320819D01* +X133990606Y-117320821D01* +X133990467Y-117321158D01* +X133989725Y-117322949D01* +X133988964Y-117323893D01* +X133987736Y-117326191D01* +X133987300Y-117325958D01* +X133945885Y-117377354D01* +X133879592Y-117399421D01* +X133875162Y-117399500D01* +X133821155Y-117399500D01* +X133666510Y-117430261D01* +X133666498Y-117430264D01* +X133520822Y-117490604D01* +X133520820Y-117490605D01* +X133518885Y-117491899D01* +X133517717Y-117492264D01* +X133515451Y-117493476D01* +X133515221Y-117493045D01* +X133452206Y-117512773D01* +X133384827Y-117494285D01* +X133381115Y-117491899D01* +X133379179Y-117490605D01* +X133379177Y-117490604D01* +X133233501Y-117430264D01* +X133233489Y-117430261D01* +X133078845Y-117399500D01* +X133078842Y-117399500D01* +X132921158Y-117399500D01* +X132921155Y-117399500D01* +X132766510Y-117430261D01* +X132766498Y-117430264D01* +X132620827Y-117490602D01* +X132620814Y-117490609D01* +X132489711Y-117578210D01* +X132489707Y-117578213D01* +X132378213Y-117689707D01* +X132378208Y-117689713D01* +X132325702Y-117768293D01* +X132272090Y-117813097D01* +X132202764Y-117821804D01* +X132139737Y-117791649D01* +X132103019Y-117732205D01* +X132100984Y-117723592D01* +X132096391Y-117700500D01* +X132069737Y-117566503D01* +X132057901Y-117537927D01* +X132009397Y-117420827D01* +X132009390Y-117420814D01* +X131921789Y-117289711D01* +X131921786Y-117289707D01* +X131810292Y-117178213D01* +X131810288Y-117178210D01* +X131679185Y-117090609D01* +X131679172Y-117090602D01* +X131533501Y-117030264D01* +X131533489Y-117030261D01* +X131378845Y-116999500D01* +X131378842Y-116999500D01* +X131221158Y-116999500D01* +X131221157Y-116999500D01* +X131208733Y-117001971D01* +X131139141Y-116995742D01* +X131083965Y-116952878D01* +X131060722Y-116886987D01* +X131068842Y-116839588D01* +X131067969Y-116839324D01* +X131069731Y-116833509D01* +X131069737Y-116833497D01* +X131072192Y-116821153D01* +X138599500Y-116821153D01* +X138599500Y-116978846D01* +X138630261Y-117133489D01* +X138630264Y-117133501D01* +X138690602Y-117279172D01* +X138690609Y-117279185D01* +X138778210Y-117410288D01* +X138778213Y-117410292D01* +X138889707Y-117521786D01* +X138889711Y-117521789D01* +X139020814Y-117609390D01* +X139020827Y-117609397D01* +X139089706Y-117637927D01* +X139166503Y-117669737D01* +X139321153Y-117700499D01* +X139321156Y-117700500D01* +X139321158Y-117700500D01* +X139478844Y-117700500D01* +X139478845Y-117700499D01* +X139633497Y-117669737D01* +X139779179Y-117609394D01* +X139910289Y-117521789D01* +X140021789Y-117410289D01* +X140109394Y-117279179D01* +X140169737Y-117133497D01* +X140200500Y-116978842D01* +X140200500Y-116821158D01* +X140200500Y-116821155D01* +X140200499Y-116821153D01* +X140172192Y-116678846D01* +X140169737Y-116666503D01* +X140109534Y-116521158D01* +X140109397Y-116520827D01* +X140109390Y-116520814D01* +X140021789Y-116389711D01* +X140021786Y-116389707D01* +X139910292Y-116278213D01* +X139910288Y-116278210D01* +X139779185Y-116190609D01* +X139779172Y-116190602D01* +X139633501Y-116130264D01* +X139633489Y-116130261D01* +X139478845Y-116099500D01* +X139478842Y-116099500D01* +X139321158Y-116099500D01* +X139321155Y-116099500D01* +X139166510Y-116130261D01* +X139166498Y-116130264D01* +X139020827Y-116190602D01* +X139020814Y-116190609D01* +X138889711Y-116278210D01* +X138889707Y-116278213D01* +X138778213Y-116389707D01* +X138778210Y-116389711D01* +X138690609Y-116520814D01* +X138690602Y-116520827D01* +X138630264Y-116666498D01* +X138630261Y-116666510D01* +X138599500Y-116821153D01* +X131072192Y-116821153D01* +X131100500Y-116678842D01* +X131100500Y-116521158D01* +X131100500Y-116521155D01* +X131100499Y-116521153D01* +X131074353Y-116389711D01* +X131069737Y-116366503D01* +X131069735Y-116366498D01* +X131009397Y-116220827D01* +X131009390Y-116220814D01* +X130921789Y-116089711D01* +X130921786Y-116089707D01* +X130810292Y-115978213D01* +X130810288Y-115978210D01* +X130679185Y-115890609D01* +X130679172Y-115890602D01* +X130533501Y-115830264D01* +X130533489Y-115830261D01* +X130378845Y-115799500D01* +X130378842Y-115799500D01* +X130221158Y-115799500D01* +X130221155Y-115799500D01* +X130066510Y-115830261D01* +X130066498Y-115830264D01* +X129920827Y-115890602D01* +X129920814Y-115890609D01* +X129789711Y-115978210D01* +X129789707Y-115978213D01* +X129678213Y-116089707D01* +X129678210Y-116089711D01* +X129590609Y-116220814D01* +X129590602Y-116220827D01* +X129530264Y-116366498D01* +X129530261Y-116366510D01* +X129499500Y-116521153D01* +X120250500Y-116521153D01* +X120250500Y-114021153D01* +X121899500Y-114021153D01* +X121899500Y-114178846D01* +X121930261Y-114333489D01* +X121930264Y-114333501D01* +X121990602Y-114479172D01* +X121990609Y-114479185D01* +X122078210Y-114610288D01* +X122078213Y-114610292D01* +X122189707Y-114721786D01* +X122189711Y-114721789D01* +X122320814Y-114809390D01* +X122320827Y-114809397D01* +X122458683Y-114866498D01* +X122466503Y-114869737D01* +X122621153Y-114900499D01* +X122621156Y-114900500D01* +X122621158Y-114900500D01* +X122778844Y-114900500D01* +X122778845Y-114900499D01* +X122933497Y-114869737D01* +X123079179Y-114809394D01* +X123210289Y-114721789D01* +X123321789Y-114610289D01* +X123409394Y-114479179D01* +X123469737Y-114333497D01* +X123500500Y-114178842D01* +X123500500Y-114121153D01* +X129699500Y-114121153D01* +X129699500Y-114278846D01* +X129730261Y-114433489D01* +X129730264Y-114433501D01* +X129790602Y-114579172D01* +X129790609Y-114579185D01* +X129878210Y-114710288D01* +X129878213Y-114710292D01* +X129989707Y-114821786D01* +X129989711Y-114821789D01* +X130120814Y-114909390D01* +X130120827Y-114909397D01* +X130266498Y-114969735D01* +X130266503Y-114969737D01* +X130396982Y-114995691D01* +X130421153Y-115000499D01* +X130421156Y-115000500D01* +X130421158Y-115000500D01* +X130578844Y-115000500D01* +X130578845Y-115000499D01* +X130733497Y-114969737D01* +X130733509Y-114969731D01* +X130739324Y-114967969D01* +X130740158Y-114970720D01* +X130797359Y-114964497D01* +X130859878Y-114995691D01* +X130895608Y-115055734D01* +X130899500Y-115086555D01* +X130899500Y-115178846D01* +X130930261Y-115333489D01* +X130930264Y-115333501D01* +X130990602Y-115479172D01* +X130990609Y-115479185D01* +X131078210Y-115610288D01* +X131078213Y-115610292D01* +X131189707Y-115721786D01* +X131189711Y-115721789D01* +X131320814Y-115809390D01* +X131320827Y-115809397D01* +X131466498Y-115869735D01* +X131466503Y-115869737D01* +X131621153Y-115900499D01* +X131621156Y-115900500D01* +X131621158Y-115900500D01* +X131778844Y-115900500D01* +X131778845Y-115900499D01* +X131933497Y-115869737D01* +X132079179Y-115809394D01* +X132210289Y-115721789D01* +X132321789Y-115610289D01* +X132409394Y-115479179D01* +X132469737Y-115333497D01* +X132500500Y-115178842D01* +X132500500Y-115021158D01* +X132500500Y-115021155D01* +X132500499Y-115021153D01* +X132478269Y-114909397D01* +X132469737Y-114866503D01* +X132409794Y-114721786D01* +X132409397Y-114720827D01* +X132409390Y-114720814D01* +X132321789Y-114589711D01* +X132321786Y-114589707D01* +X132210292Y-114478213D01* +X132210288Y-114478210D01* +X132079185Y-114390609D01* +X132079172Y-114390602D01* +X131933501Y-114330264D01* +X131933489Y-114330261D01* +X131778845Y-114299500D01* +X131778842Y-114299500D01* +X131621158Y-114299500D01* +X131621155Y-114299500D01* +X131466510Y-114330261D01* +X131460676Y-114332031D01* +X131459873Y-114329385D01* +X131444688Y-114330963D01* +X131418434Y-114337296D01* +X131410455Y-114334522D01* +X131402056Y-114335396D01* +X131377950Y-114323223D01* +X131352437Y-114314355D01* +X131347224Y-114307708D01* +X131339687Y-114303902D01* +X131325988Y-114280629D01* +X131309321Y-114259376D01* +X131307307Y-114248892D01* +X131304245Y-114243689D01* +X131301046Y-114225065D01* +X131300500Y-114219264D01* +X131300500Y-114121158D01* +X131280608Y-114021153D01* +X138799500Y-114021153D01* +X138799500Y-114178846D01* +X138830261Y-114333489D01* +X138830264Y-114333501D01* +X138890602Y-114479172D01* +X138890609Y-114479185D01* +X138978210Y-114610288D01* +X138978213Y-114610292D01* +X139089707Y-114721786D01* +X139089711Y-114721789D01* +X139220814Y-114809390D01* +X139220827Y-114809397D01* +X139358683Y-114866498D01* +X139366503Y-114869737D01* +X139521153Y-114900499D01* +X139521156Y-114900500D01* +X139521158Y-114900500D01* +X139678844Y-114900500D01* +X139678845Y-114900499D01* +X139833497Y-114869737D01* +X139979179Y-114809394D01* +X140110289Y-114721789D01* +X140221789Y-114610289D01* +X140309394Y-114479179D01* +X140369737Y-114333497D01* +X140400500Y-114178842D01* +X140400500Y-114121153D01* +X141199500Y-114121153D01* +X141199500Y-114278846D01* +X141230261Y-114433489D01* +X141230264Y-114433501D01* +X141290602Y-114579172D01* +X141290609Y-114579185D01* +X141378210Y-114710288D01* +X141378213Y-114710292D01* +X141489707Y-114821786D01* +X141489711Y-114821789D01* +X141620814Y-114909390D01* +X141620827Y-114909397D01* +X141766498Y-114969735D01* +X141766503Y-114969737D01* +X141896982Y-114995691D01* +X141921153Y-115000499D01* +X141921156Y-115000500D01* +X141921158Y-115000500D01* +X142078844Y-115000500D01* +X142078845Y-115000499D01* +X142233497Y-114969737D01* +X142379179Y-114909394D01* +X142510289Y-114821789D01* +X142621789Y-114710289D01* +X142709394Y-114579179D01* +X142769737Y-114433497D01* +X142800500Y-114278842D01* +X142800500Y-114121158D01* +X142800500Y-114121155D01* +X142800499Y-114121153D01* +X142769737Y-113966503D01* +X142728314Y-113866498D01* +X142709397Y-113820827D01* +X142709390Y-113820814D01* +X142621789Y-113689711D01* +X142621786Y-113689707D01* +X142510292Y-113578213D01* +X142510288Y-113578210D01* +X142379185Y-113490609D01* +X142379172Y-113490602D01* +X142233501Y-113430264D01* +X142233489Y-113430261D01* +X142078845Y-113399500D01* +X142078842Y-113399500D01* +X141921158Y-113399500D01* +X141921155Y-113399500D01* +X141766510Y-113430261D01* +X141766498Y-113430264D01* +X141620827Y-113490602D01* +X141620814Y-113490609D01* +X141489711Y-113578210D01* +X141489707Y-113578213D01* +X141378213Y-113689707D01* +X141378210Y-113689711D01* +X141290609Y-113820814D01* +X141290602Y-113820827D01* +X141230264Y-113966498D01* +X141230261Y-113966510D01* +X141199500Y-114121153D01* +X140400500Y-114121153D01* +X140400500Y-114021158D01* +X140400500Y-114021155D01* +X140400499Y-114021153D01* +X140369738Y-113866510D01* +X140369737Y-113866503D01* +X140350812Y-113820814D01* +X140309397Y-113720827D01* +X140309390Y-113720814D01* +X140221789Y-113589711D01* +X140221786Y-113589707D01* +X140110292Y-113478213D01* +X140110288Y-113478210D01* +X139979185Y-113390609D01* +X139979172Y-113390602D01* +X139833501Y-113330264D01* +X139833489Y-113330261D01* +X139678845Y-113299500D01* +X139678842Y-113299500D01* +X139521158Y-113299500D01* +X139521155Y-113299500D01* +X139366510Y-113330261D01* +X139366498Y-113330264D01* +X139220827Y-113390602D01* +X139220814Y-113390609D01* +X139089711Y-113478210D01* +X139089707Y-113478213D01* +X138978213Y-113589707D01* +X138978210Y-113589711D01* +X138890609Y-113720814D01* +X138890602Y-113720827D01* +X138830264Y-113866498D01* +X138830261Y-113866510D01* +X138799500Y-114021153D01* +X131280608Y-114021153D01* +X131269737Y-113966503D01* +X131228314Y-113866498D01* +X131209397Y-113820827D01* +X131209390Y-113820814D01* +X131121789Y-113689711D01* +X131121786Y-113689707D01* +X131010292Y-113578213D01* +X131010288Y-113578210D01* +X130879185Y-113490609D01* +X130879172Y-113490602D01* +X130733501Y-113430264D01* +X130733489Y-113430261D01* +X130578845Y-113399500D01* +X130578842Y-113399500D01* +X130421158Y-113399500D01* +X130421155Y-113399500D01* +X130266510Y-113430261D01* +X130266498Y-113430264D01* +X130120827Y-113490602D01* +X130120814Y-113490609D01* +X129989711Y-113578210D01* +X129989707Y-113578213D01* +X129878213Y-113689707D01* +X129878210Y-113689711D01* +X129790609Y-113820814D01* +X129790602Y-113820827D01* +X129730264Y-113966498D01* +X129730261Y-113966510D01* +X129699500Y-114121153D01* +X123500500Y-114121153D01* +X123500500Y-114021158D01* +X123500500Y-114021155D01* +X123500499Y-114021153D01* +X123469738Y-113866510D01* +X123469737Y-113866503D01* +X123450812Y-113820814D01* +X123409397Y-113720827D01* +X123409390Y-113720814D01* +X123321789Y-113589711D01* +X123321786Y-113589707D01* +X123210292Y-113478213D01* +X123210288Y-113478210D01* +X123079185Y-113390609D01* +X123079172Y-113390602D01* +X122933501Y-113330264D01* +X122933489Y-113330261D01* +X122778845Y-113299500D01* +X122778842Y-113299500D01* +X122621158Y-113299500D01* +X122621155Y-113299500D01* +X122466510Y-113330261D01* +X122466498Y-113330264D01* +X122320827Y-113390602D01* +X122320814Y-113390609D01* +X122189711Y-113478210D01* +X122189707Y-113478213D01* +X122078213Y-113589707D01* +X122078210Y-113589711D01* +X121990609Y-113720814D01* +X121990602Y-113720827D01* +X121930264Y-113866498D01* +X121930261Y-113866510D01* +X121899500Y-114021153D01* +X120250500Y-114021153D01* +X120250500Y-111521153D01* +X123399500Y-111521153D01* +X123399500Y-111678846D01* +X123430261Y-111833489D01* +X123430264Y-111833501D01* +X123490602Y-111979172D01* +X123490609Y-111979185D01* +X123578210Y-112110288D01* +X123578213Y-112110292D01* +X123689707Y-112221786D01* +X123689711Y-112221789D01* +X123820814Y-112309390D01* +X123820827Y-112309397D01* +X123966498Y-112369735D01* +X123966503Y-112369737D01* +X124121153Y-112400499D01* +X124121156Y-112400500D01* +X124121158Y-112400500D01* +X124278844Y-112400500D01* +X124278845Y-112400499D01* +X124433497Y-112369737D01* +X124579179Y-112309394D01* +X124710289Y-112221789D01* +X124821789Y-112110289D01* +X124909394Y-111979179D01* +X124969737Y-111833497D01* +X125000500Y-111678842D01* +X125000500Y-111521158D01* +X125000500Y-111521155D01* +X125000499Y-111521153D01* +X124980734Y-111421789D01* +X124969737Y-111366503D01* +X124946452Y-111310288D01* +X124909397Y-111220827D01* +X124909390Y-111220814D01* +X124821789Y-111089711D01* +X124821786Y-111089707D01* +X124710292Y-110978213D01* +X124710288Y-110978210D01* +X124579185Y-110890609D01* +X124579172Y-110890602D01* +X124458154Y-110840475D01* +X124458147Y-110840473D01* +X124433497Y-110830263D01* +X124278842Y-110799500D01* +X124121158Y-110799500D01* +X124121155Y-110799500D01* +X123966510Y-110830261D01* +X123966498Y-110830264D01* +X123820827Y-110890602D01* +X123820814Y-110890609D01* +X123689711Y-110978210D01* +X123689707Y-110978213D01* +X123578213Y-111089707D01* +X123578210Y-111089711D01* +X123490609Y-111220814D01* +X123490602Y-111220827D01* +X123430264Y-111366498D01* +X123430261Y-111366510D01* +X123399500Y-111521153D01* +X120250500Y-111521153D01* +X120250500Y-109721153D01* +X123799500Y-109721153D01* +X123799500Y-109878846D01* +X123830261Y-110033489D01* +X123830264Y-110033501D01* +X123890602Y-110179172D01* +X123890609Y-110179185D01* +X123978210Y-110310288D01* +X123978213Y-110310292D01* +X124089707Y-110421786D01* +X124089711Y-110421789D01* +X124220814Y-110509390D01* +X124220827Y-110509397D01* +X124341844Y-110559523D01* +X124366503Y-110569737D01* +X124521158Y-110600500D01* +X124521249Y-110600500D01* +X124678844Y-110600500D01* +X124678845Y-110600499D01* +X124833497Y-110569737D01* +X124979179Y-110509394D01* +X125110289Y-110421789D01* +X125170144Y-110361933D01* +X125231463Y-110328450D01* +X125301155Y-110333434D01* +X125326714Y-110346514D01* +X125420814Y-110409390D01* +X125420827Y-110409397D01* +X125566498Y-110469735D01* +X125566503Y-110469737D01* +X125721153Y-110500499D01* +X125721156Y-110500500D01* +X125721158Y-110500500D01* +X125878844Y-110500500D01* +X125878845Y-110500499D01* +X126033497Y-110469737D01* +X126151592Y-110420821D01* +X126179172Y-110409397D01* +X126179172Y-110409396D01* +X126179179Y-110409394D01* +X126310289Y-110321789D01* +X126421789Y-110210289D01* +X126509394Y-110079179D01* +X126569737Y-109933497D01* +X126592083Y-109821158D01* +X126592084Y-109821153D01* +X129599500Y-109821153D01* +X129599500Y-109978846D01* +X129630261Y-110133489D01* +X129630264Y-110133501D01* +X129690602Y-110279172D01* +X129690612Y-110279190D01* +X129751732Y-110370663D01* +X129772610Y-110437340D01* +X129763192Y-110487004D01* +X129730262Y-110566506D01* +X129730260Y-110566511D01* +X129699500Y-110721153D01* +X129699500Y-110878846D01* +X129730261Y-111033489D01* +X129730264Y-111033501D01* +X129790602Y-111179172D01* +X129790609Y-111179185D01* +X129878210Y-111310288D01* +X129878213Y-111310292D01* +X129989707Y-111421786D01* +X129989711Y-111421789D01* +X130120814Y-111509390D01* +X130120827Y-111509397D01* +X130266498Y-111569735D01* +X130266503Y-111569737D01* +X130421153Y-111600499D01* +X130421156Y-111600500D01* +X130421158Y-111600500D01* +X130578844Y-111600500D01* +X130578845Y-111600499D01* +X130733497Y-111569737D01* +X130879179Y-111509394D01* +X131010289Y-111421789D01* +X131121789Y-111310289D01* +X131209394Y-111179179D01* +X131269737Y-111033497D01* +X131300500Y-110878842D01* +X131300500Y-110721158D01* +X131300500Y-110721155D01* +X131300499Y-110721153D01* +X131270380Y-110569735D01* +X131269737Y-110566503D01* +X131242398Y-110500500D01* +X131209397Y-110420827D01* +X131209390Y-110420814D01* +X131148267Y-110329337D01* +X131127389Y-110262659D01* +X131136808Y-110212993D01* +X131137928Y-110210289D01* +X131169737Y-110133497D01* +X131200500Y-109978842D01* +X131200500Y-109821158D01* +X131200500Y-109821155D01* +X131176982Y-109702925D01* +X131183209Y-109633333D01* +X131226072Y-109578156D01* +X131229675Y-109575653D01* +X131310289Y-109521789D01* +X131421789Y-109410289D01* +X131509394Y-109279179D01* +X131533429Y-109221153D01* +X146499500Y-109221153D01* +X146499500Y-109378846D01* +X146530261Y-109533489D01* +X146530264Y-109533501D01* +X146590602Y-109679172D01* +X146590609Y-109679185D01* +X146678210Y-109810288D01* +X146678213Y-109810292D01* +X146789707Y-109921786D01* +X146789711Y-109921789D01* +X146920814Y-110009390D01* +X146920827Y-110009397D01* +X147066498Y-110069735D01* +X147066503Y-110069737D01* +X147221153Y-110100499D01* +X147221156Y-110100500D01* +X147221158Y-110100500D01* +X147378844Y-110100500D01* +X147378845Y-110100499D01* +X147533497Y-110069737D01* +X147679179Y-110009394D01* +X147810289Y-109921789D01* +X147921789Y-109810289D01* +X148009394Y-109679179D01* +X148069737Y-109533497D01* +X148100500Y-109378842D01* +X148100500Y-109221158D01* +X148100500Y-109221155D01* +X148100499Y-109221153D01* +X148074531Y-109090606D01* +X148069737Y-109066503D01* +X148069735Y-109066498D01* +X148009397Y-108920827D01* +X148009390Y-108920814D01* +X147921789Y-108789711D01* +X147921786Y-108789707D01* +X147810292Y-108678213D01* +X147810288Y-108678210D01* +X147679185Y-108590609D01* +X147679172Y-108590602D01* +X147533501Y-108530264D01* +X147533489Y-108530261D01* +X147378845Y-108499500D01* +X147378842Y-108499500D01* +X147221158Y-108499500D01* +X147221155Y-108499500D01* +X147066510Y-108530261D01* +X147066498Y-108530264D01* +X146920827Y-108590602D01* +X146920814Y-108590609D01* +X146789711Y-108678210D01* +X146789707Y-108678213D01* +X146678213Y-108789707D01* +X146678210Y-108789711D01* +X146590609Y-108920814D01* +X146590602Y-108920827D01* +X146530264Y-109066498D01* +X146530261Y-109066510D01* +X146499500Y-109221153D01* +X131533429Y-109221153D01* +X131569737Y-109133497D01* +X131600500Y-108978842D01* +X131600500Y-108821158D01* +X131600500Y-108821155D01* +X131600499Y-108821153D01* +X131594244Y-108789707D01* +X131569737Y-108666503D01* +X131527049Y-108563446D01* +X131519581Y-108493978D01* +X131532264Y-108457521D01* +X131533649Y-108454928D01* +X131533659Y-108454914D01* +X131594002Y-108309232D01* +X131611522Y-108221153D01* +X144099500Y-108221153D01* +X144099500Y-108378846D01* +X144130261Y-108533489D01* +X144130264Y-108533501D01* +X144190602Y-108679172D01* +X144190609Y-108679185D01* +X144278210Y-108810288D01* +X144278213Y-108810292D01* +X144389707Y-108921786D01* +X144389711Y-108921789D01* +X144520814Y-109009390D01* +X144520827Y-109009397D01* +X144658683Y-109066498D01* +X144666503Y-109069737D01* +X144821153Y-109100499D01* +X144821156Y-109100500D01* +X144821158Y-109100500D01* +X144978844Y-109100500D01* +X144978845Y-109100499D01* +X144996061Y-109097075D01* +X145014287Y-109093450D01* +X145014292Y-109093449D01* +X145099800Y-109076439D01* +X145133497Y-109069737D01* +X145279179Y-109009394D01* +X145410289Y-108921789D01* +X145521789Y-108810289D01* +X145609394Y-108679179D01* +X145669737Y-108533497D01* +X145700500Y-108378842D01* +X145700500Y-108221158D01* +X145700500Y-108221155D01* +X145700499Y-108221153D01* +X145687257Y-108154581D01* +X145669737Y-108066503D01* +X145609794Y-107921786D01* +X145609397Y-107920827D01* +X145609390Y-107920814D01* +X145521789Y-107789711D01* +X145521786Y-107789707D01* +X145410292Y-107678213D01* +X145410288Y-107678210D01* +X145279185Y-107590609D01* +X145279172Y-107590602D01* +X145133501Y-107530264D01* +X145133489Y-107530261D01* +X144978845Y-107499500D01* +X144978842Y-107499500D01* +X144821158Y-107499500D01* +X144821155Y-107499500D01* +X144666510Y-107530261D01* +X144666498Y-107530264D01* +X144520827Y-107590602D01* +X144520814Y-107590609D01* +X144389711Y-107678210D01* +X144389707Y-107678213D01* +X144278213Y-107789707D01* +X144278210Y-107789711D01* +X144190609Y-107920814D01* +X144190602Y-107920827D01* +X144130264Y-108066498D01* +X144130261Y-108066510D01* +X144099500Y-108221153D01* +X131611522Y-108221153D01* +X131624765Y-108154577D01* +X131624765Y-107996893D01* +X131624765Y-107996890D01* +X131624764Y-107996888D01* +X131594003Y-107842245D01* +X131594002Y-107842238D01* +X131580770Y-107810292D01* +X131533662Y-107696562D01* +X131533655Y-107696549D01* +X131446054Y-107565446D01* +X131446051Y-107565442D01* +X131344025Y-107463416D01* +X131310540Y-107402093D01* +X131315524Y-107332401D01* +X131344025Y-107288054D01* +X131421786Y-107210292D01* +X131421789Y-107210289D01* +X131509394Y-107079179D01* +X131569737Y-106933497D01* +X131572192Y-106921153D01* +X132299500Y-106921153D01* +X132299500Y-107078846D01* +X132330261Y-107233489D01* +X132330264Y-107233501D01* +X132390602Y-107379172D01* +X132390609Y-107379185D01* +X132478210Y-107510288D01* +X132478213Y-107510292D01* +X132589707Y-107621786D01* +X132589711Y-107621789D01* +X132720814Y-107709390D01* +X132720827Y-107709397D01* +X132866498Y-107769735D01* +X132866503Y-107769737D01* +X133021153Y-107800499D01* +X133021156Y-107800500D01* +X133021158Y-107800500D01* +X133178844Y-107800500D01* +X133178845Y-107800499D01* +X133333497Y-107769737D01* +X133479179Y-107709394D01* +X133610289Y-107621789D01* +X133721789Y-107510289D01* +X133809394Y-107379179D01* +X133811688Y-107373642D01* +X133828770Y-107332401D01* +X133869737Y-107233497D01* +X133900500Y-107078842D01* +X133900500Y-106921158D01* +X133900500Y-106921155D01* +X133900499Y-106921153D01* +X133882347Y-106829897D01* +X133869737Y-106766503D01* +X133835650Y-106684208D01* +X133809397Y-106620827D01* +X133809390Y-106620814D01* +X133721789Y-106489711D01* +X133721786Y-106489707D01* +X133610292Y-106378213D01* +X133610288Y-106378210D01* +X133479185Y-106290609D01* +X133479172Y-106290602D01* +X133333501Y-106230264D01* +X133333489Y-106230261D01* +X133178845Y-106199500D01* +X133178842Y-106199500D01* +X133021158Y-106199500D01* +X133021155Y-106199500D01* +X132866510Y-106230261D01* +X132866498Y-106230264D01* +X132720827Y-106290602D01* +X132720814Y-106290609D01* +X132589711Y-106378210D01* +X132589707Y-106378213D01* +X132478213Y-106489707D01* +X132478210Y-106489711D01* +X132390609Y-106620814D01* +X132390602Y-106620827D01* +X132330264Y-106766498D01* +X132330261Y-106766510D01* +X132299500Y-106921153D01* +X131572192Y-106921153D01* +X131572257Y-106920827D01* +X131578216Y-106890874D01* +X131578216Y-106890873D01* +X131600499Y-106778846D01* +X131600500Y-106778844D01* +X131600500Y-106621155D01* +X131600499Y-106621153D01* +X131574353Y-106489711D01* +X131569737Y-106466503D01* +X131551233Y-106421829D01* +X131509397Y-106320827D01* +X131509390Y-106320814D01* +X131421789Y-106189711D01* +X131421786Y-106189707D01* +X131353232Y-106121153D01* +X138099500Y-106121153D01* +X138099500Y-106278846D01* +X138130261Y-106433489D01* +X138130264Y-106433501D01* +X138190602Y-106579172D01* +X138190609Y-106579185D01* +X138278210Y-106710288D01* +X138278213Y-106710292D01* +X138389707Y-106821786D01* +X138389711Y-106821789D01* +X138520814Y-106909390D01* +X138520827Y-106909397D01* +X138656158Y-106965452D01* +X138666503Y-106969737D01* +X138821153Y-107000499D01* +X138821156Y-107000500D01* +X138821158Y-107000500D01* +X138978844Y-107000500D01* +X138978845Y-107000499D01* +X139133497Y-106969737D01* +X139201315Y-106941645D01* +X139270782Y-106934177D01* +X139333261Y-106965452D01* +X139336447Y-106968526D01* +X139389707Y-107021786D01* +X139389711Y-107021789D01* +X139520814Y-107109390D01* +X139520827Y-107109397D01* +X139666498Y-107169735D01* +X139666503Y-107169737D01* +X139821153Y-107200499D01* +X139821156Y-107200500D01* +X139821158Y-107200500D01* +X139978844Y-107200500D01* +X139978845Y-107200499D01* +X140133497Y-107169737D01* +X140279179Y-107109394D01* +X140410289Y-107021789D01* +X140428606Y-107003472D01* +X140489928Y-106969985D01* +X140559620Y-106974968D01* +X140615554Y-107016838D01* +X140619391Y-107022260D01* +X140678210Y-107110288D01* +X140678213Y-107110292D01* +X140789707Y-107221786D01* +X140789711Y-107221789D01* +X140920814Y-107309390D01* +X140920827Y-107309397D01* +X140950745Y-107321789D01* +X141066503Y-107369737D01* +X141121831Y-107380742D01* +X141183740Y-107413126D01* +X141218315Y-107473841D01* +X141219256Y-107478166D01* +X141230261Y-107533492D01* +X141230264Y-107533501D01* +X141290602Y-107679172D01* +X141290609Y-107679185D01* +X141378210Y-107810288D01* +X141378213Y-107810292D01* +X141489707Y-107921786D01* +X141489711Y-107921789D01* +X141620814Y-108009390D01* +X141620827Y-108009397D01* +X141758683Y-108066498D01* +X141766503Y-108069737D01* +X141921153Y-108100499D01* +X141921156Y-108100500D01* +X141921158Y-108100500D01* +X142078844Y-108100500D01* +X142078845Y-108100499D01* +X142089179Y-108098443D01* +X142114287Y-108093450D01* +X142114292Y-108093449D01* +X142199800Y-108076439D01* +X142233497Y-108069737D01* +X142379179Y-108009394D01* +X142510289Y-107921789D01* +X142621789Y-107810289D01* +X142709394Y-107679179D01* +X142769737Y-107533497D01* +X142800500Y-107378842D01* +X142800500Y-107221158D01* +X142800500Y-107221155D01* +X142800499Y-107221153D01* +X142778447Y-107110292D01* +X142769737Y-107066503D01* +X142742398Y-107000500D01* +X142709397Y-106920827D01* +X142709390Y-106920814D01* +X142621789Y-106789711D01* +X142621786Y-106789707D01* +X142510292Y-106678213D01* +X142510288Y-106678210D01* +X142379185Y-106590609D01* +X142379172Y-106590602D01* +X142233501Y-106530264D01* +X142233492Y-106530261D01* +X142178166Y-106519256D01* +X142116256Y-106486870D01* +X142081682Y-106426154D01* +X142080750Y-106421874D01* +X142069737Y-106366503D01* +X142047854Y-106313673D01* +X142009397Y-106220827D01* +X142009390Y-106220814D01* +X141921789Y-106089711D01* +X141921786Y-106089707D01* +X141810292Y-105978213D01* +X141810288Y-105978210D01* +X141679185Y-105890609D01* +X141679172Y-105890602D01* +X141533501Y-105830264D01* +X141533489Y-105830261D01* +X141378845Y-105799500D01* +X141378842Y-105799500D01* +X141221158Y-105799500D01* +X141221155Y-105799500D01* +X141066510Y-105830261D01* +X141066498Y-105830264D01* +X140920827Y-105890602D01* +X140920814Y-105890609D01* +X140789711Y-105978210D01* +X140789706Y-105978214D01* +X140771389Y-105996531D01* +X140710065Y-106030015D01* +X140640374Y-106025029D01* +X140584441Y-105983156D01* +X140580608Y-105977739D01* +X140521789Y-105889711D01* +X140521786Y-105889707D01* +X140410292Y-105778213D01* +X140410288Y-105778210D01* +X140279185Y-105690609D01* +X140279172Y-105690602D01* +X140133501Y-105630264D01* +X140133489Y-105630261D01* +X139978845Y-105599500D01* +X139978842Y-105599500D01* +X139821158Y-105599500D01* +X139821155Y-105599500D01* +X139666505Y-105630261D01* +X139666497Y-105630264D01* +X139598682Y-105658353D01* +X139529213Y-105665820D01* +X139466734Y-105634544D01* +X139463551Y-105631472D01* +X139410292Y-105578213D01* +X139410288Y-105578210D01* +X139279185Y-105490609D01* +X139279172Y-105490602D01* +X139133501Y-105430264D01* +X139133489Y-105430261D01* +X138978845Y-105399500D01* +X138978842Y-105399500D01* +X138821158Y-105399500D01* +X138821155Y-105399500D01* +X138666510Y-105430261D01* +X138666498Y-105430264D01* +X138520827Y-105490602D01* +X138520814Y-105490609D01* +X138389711Y-105578210D01* +X138389707Y-105578213D01* +X138278213Y-105689707D01* +X138278210Y-105689711D01* +X138190609Y-105820814D01* +X138190602Y-105820827D01* +X138130264Y-105966498D01* +X138130261Y-105966510D01* +X138099500Y-106121153D01* +X131353232Y-106121153D01* +X131310292Y-106078213D01* +X131310288Y-106078210D01* +X131179185Y-105990609D01* +X131179172Y-105990602D01* +X131033501Y-105930264D01* +X131033489Y-105930261D01* +X130878845Y-105899500D01* +X130878842Y-105899500D01* +X130721158Y-105899500D01* +X130721155Y-105899500D01* +X130566510Y-105930261D01* +X130566498Y-105930264D01* +X130420827Y-105990602D01* +X130420814Y-105990609D01* +X130289711Y-106078210D01* +X130289707Y-106078213D01* +X130178213Y-106189707D01* +X130178210Y-106189711D01* +X130090609Y-106320814D01* +X130090602Y-106320827D01* +X130030264Y-106466498D01* +X130030261Y-106466510D01* +X129999500Y-106621153D01* +X129999500Y-106778846D01* +X130030261Y-106933489D01* +X130030264Y-106933501D01* +X130090602Y-107079172D01* +X130090609Y-107079185D01* +X130178210Y-107210288D01* +X130178213Y-107210292D01* +X130280240Y-107312319D01* +X130313725Y-107373642D01* +X130308741Y-107443334D01* +X130280240Y-107487681D01* +X130202478Y-107565442D01* +X130202475Y-107565446D01* +X130114874Y-107696549D01* +X130114867Y-107696562D01* +X130054529Y-107842233D01* +X130054526Y-107842245D01* +X130023765Y-107996888D01* +X130023765Y-108154581D01* +X130054526Y-108309224D01* +X130054529Y-108309236D01* +X130097213Y-108412286D01* +X130104682Y-108481756D01* +X130092020Y-108518173D01* +X130090608Y-108520815D01* +X130030264Y-108666498D01* +X130030261Y-108666510D01* +X129999500Y-108821153D01* +X129999500Y-108978846D01* +X130023017Y-109097075D01* +X130016790Y-109166667D01* +X129973927Y-109221844D01* +X129970291Y-109224368D01* +X129889711Y-109278210D01* +X129889707Y-109278213D01* +X129778213Y-109389707D01* +X129778210Y-109389711D01* +X129690609Y-109520814D01* +X129690602Y-109520827D01* +X129630264Y-109666498D01* +X129630261Y-109666510D01* +X129599500Y-109821153D01* +X126592084Y-109821153D01* +X126598107Y-109790875D01* +X126598107Y-109790874D01* +X126600500Y-109778844D01* +X126600500Y-109621155D01* +X126600499Y-109621153D01* +X126580734Y-109521789D01* +X126569737Y-109466503D01* +X126537929Y-109389711D01* +X126509397Y-109320827D01* +X126509390Y-109320814D01* +X126421789Y-109189711D01* +X126421786Y-109189707D01* +X126310292Y-109078213D01* +X126310288Y-109078210D01* +X126179185Y-108990609D01* +X126179172Y-108990602D01* +X126033501Y-108930264D01* +X126033489Y-108930261D01* +X125878845Y-108899500D01* +X125878842Y-108899500D01* +X125721158Y-108899500D01* +X125721155Y-108899500D01* +X125566510Y-108930261D01* +X125566498Y-108930264D01* +X125420827Y-108990602D01* +X125420814Y-108990609D01* +X125289711Y-109078210D01* +X125289707Y-109078213D01* +X125229857Y-109138064D01* +X125168534Y-109171549D01* +X125098842Y-109166565D01* +X125073285Y-109153485D01* +X124979185Y-109090609D01* +X124979172Y-109090602D01* +X124833501Y-109030264D01* +X124833489Y-109030261D01* +X124678845Y-108999500D01* +X124678842Y-108999500D01* +X124521158Y-108999500D01* +X124521155Y-108999500D01* +X124366510Y-109030261D01* +X124366498Y-109030264D01* +X124220827Y-109090602D01* +X124220814Y-109090609D01* +X124089711Y-109178210D01* +X124089707Y-109178213D01* +X123978213Y-109289707D01* +X123978210Y-109289711D01* +X123890609Y-109420814D01* +X123890602Y-109420827D01* +X123830264Y-109566498D01* +X123830261Y-109566510D01* +X123799500Y-109721153D01* +X120250500Y-109721153D01* +X120250500Y-106984540D01* +X121073430Y-106984540D01* +X121073430Y-107142233D01* +X121104191Y-107296876D01* +X121104194Y-107296888D01* +X121164532Y-107442559D01* +X121164539Y-107442572D01* +X121252140Y-107573675D01* +X121252143Y-107573679D01* +X121363637Y-107685173D01* +X121363641Y-107685176D01* +X121494744Y-107772777D01* +X121494757Y-107772784D01* +X121585311Y-107810292D01* +X121640433Y-107833124D01* +X121795083Y-107863886D01* +X121795086Y-107863887D01* +X121795088Y-107863887D01* +X121952774Y-107863887D01* +X121952775Y-107863886D01* +X122107427Y-107833124D01* +X122253109Y-107772781D01* +X122384219Y-107685176D01* +X122495719Y-107573676D01* +X122583324Y-107442566D01* +X122643667Y-107296884D01* +X122674430Y-107142229D01* +X122674430Y-106984545D01* +X122674430Y-106984542D01* +X122674429Y-106984540D01* +X122661820Y-106921153D01* +X122643667Y-106829890D01* +X122598102Y-106719887D01* +X122590634Y-106650419D01* +X122601294Y-106619772D01* +X122600963Y-106619635D01* +X122663635Y-106468328D01* +X122663637Y-106468324D01* +X122694400Y-106313669D01* +X122694400Y-106155985D01* +X122694400Y-106155982D01* +X122694399Y-106155980D01* +X122678930Y-106078213D01* +X122663637Y-106001330D01* +X122654061Y-105978211D01* +X122603297Y-105855654D01* +X122603290Y-105855641D01* +X122515689Y-105724538D01* +X122515686Y-105724534D01* +X122404192Y-105613040D01* +X122404188Y-105613037D01* +X122273085Y-105525436D01* +X122273072Y-105525429D01* +X122162498Y-105479629D01* +X122127397Y-105465090D01* +X122127389Y-105465088D01* +X121972745Y-105434327D01* +X121972742Y-105434327D01* +X121815058Y-105434327D01* +X121815055Y-105434327D01* +X121660410Y-105465088D01* +X121660398Y-105465091D01* +X121514727Y-105525429D01* +X121514714Y-105525436D01* +X121383611Y-105613037D01* +X121383607Y-105613040D01* +X121272113Y-105724534D01* +X121272110Y-105724538D01* +X121184509Y-105855641D01* +X121184502Y-105855654D01* +X121124164Y-106001325D01* +X121124161Y-106001337D01* +X121093400Y-106155980D01* +X121093400Y-106313673D01* +X121124161Y-106468316D01* +X121124164Y-106468328D01* +X121169726Y-106578325D01* +X121177195Y-106647794D01* +X121166538Y-106678443D01* +X121166867Y-106678580D01* +X121104194Y-106829885D01* +X121104191Y-106829897D01* +X121073430Y-106984540D01* +X120250500Y-106984540D01* +X120250500Y-105371155D01* +X127399500Y-105371155D01* +X127399500Y-105528848D01* +X127430261Y-105683491D01* +X127430264Y-105683503D01* +X127490602Y-105829174D01* +X127490609Y-105829187D01* +X127578210Y-105960290D01* +X127578213Y-105960294D01* +X127689707Y-106071788D01* +X127689711Y-106071791D01* +X127820814Y-106159392D01* +X127820827Y-106159399D01* +X127894008Y-106189711D01* +X127966503Y-106219739D01* +X128121153Y-106250501D01* +X128121156Y-106250502D01* +X128121158Y-106250502D01* +X128278844Y-106250502D01* +X128278845Y-106250501D01* +X128433497Y-106219739D01* +X128579179Y-106159396D01* +X128710289Y-106071791D01* +X128821789Y-105960291D01* +X128909394Y-105829181D01* +X128969737Y-105683499D01* +X129000500Y-105528844D01* +X129000500Y-105371160D01* +X129000500Y-105371157D01* +X129000499Y-105371155D01* +X128969738Y-105216512D01* +X128969737Y-105216505D01* +X128969735Y-105216500D01* +X128909397Y-105070829D01* +X128909390Y-105070816D01* +X128821789Y-104939713D01* +X128821786Y-104939709D01* +X128710292Y-104828215D01* +X128710288Y-104828212D01* +X128579185Y-104740611D01* +X128579172Y-104740604D01* +X128433501Y-104680266D01* +X128433489Y-104680263D01* +X128278845Y-104649502D01* +X128278842Y-104649502D01* +X128121158Y-104649502D01* +X128121155Y-104649502D01* +X127966510Y-104680263D01* +X127966498Y-104680266D01* +X127820827Y-104740604D01* +X127820814Y-104740611D01* +X127689711Y-104828212D01* +X127689707Y-104828215D01* +X127578213Y-104939709D01* +X127578210Y-104939713D01* +X127490609Y-105070816D01* +X127490602Y-105070829D01* +X127430264Y-105216500D01* +X127430261Y-105216512D01* +X127399500Y-105371155D01* +X120250500Y-105371155D01* +X120250500Y-102721153D01* +X121499500Y-102721153D01* +X121499500Y-102878846D01* +X121530261Y-103033489D01* +X121530264Y-103033501D01* +X121590602Y-103179172D01* +X121590609Y-103179185D01* +X121678210Y-103310288D01* +X121678213Y-103310292D01* +X121789707Y-103421786D01* +X121789715Y-103421792D01* +X121848995Y-103461402D01* +X121893801Y-103515014D01* +X121902508Y-103584339D01* +X121892194Y-103614885D01* +X121892937Y-103615193D01* +X121830264Y-103766498D01* +X121830261Y-103766510D01* +X121799500Y-103921153D01* +X121799500Y-104078846D01* +X121830261Y-104233489D01* +X121830264Y-104233501D01* +X121890602Y-104379172D01* +X121890609Y-104379185D01* +X121978210Y-104510288D01* +X121978213Y-104510292D01* +X122089707Y-104621786D01* +X122089711Y-104621789D01* +X122220814Y-104709390D01* +X122220827Y-104709397D01* +X122366498Y-104769735D01* +X122366503Y-104769737D01* +X122521153Y-104800499D01* +X122521156Y-104800500D01* +X122521158Y-104800500D01* +X122678844Y-104800500D01* +X122678845Y-104800499D01* +X122833497Y-104769737D01* +X122979179Y-104709394D01* +X123110289Y-104621789D01* +X123221789Y-104510289D01* +X123309394Y-104379179D01* +X123369737Y-104233497D01* +X123400500Y-104078842D01* +X123400500Y-103921158D01* +X123400500Y-103921155D01* +X123400499Y-103921153D01* +X123369738Y-103766510D01* +X123369737Y-103766503D01* +X123309794Y-103621786D01* +X123309397Y-103620827D01* +X123309390Y-103620814D01* +X123221789Y-103489711D01* +X123221786Y-103489707D01* +X123110292Y-103378213D01* +X123110288Y-103378210D01* +X123051003Y-103338597D01* +X123006198Y-103284985D01* +X122997491Y-103215660D01* +X123007811Y-103185117D01* +X123007063Y-103184808D01* +X123069735Y-103033501D01* +X123069737Y-103033497D01* +X123092083Y-102921158D01* +X123092084Y-102921153D01* +X136999498Y-102921153D01* +X136999498Y-103078846D01* +X137030259Y-103233489D01* +X137030262Y-103233501D01* +X137090600Y-103379172D01* +X137090607Y-103379185D01* +X137178208Y-103510288D01* +X137178211Y-103510292D01* +X137289705Y-103621786D01* +X137289709Y-103621789D01* +X137420812Y-103709390D01* +X137420825Y-103709397D01* +X137558681Y-103766498D01* +X137566501Y-103769737D01* +X137721151Y-103800499D01* +X137721154Y-103800500D01* +X137721156Y-103800500D01* +X137878842Y-103800500D01* +X137878843Y-103800499D01* +X138033495Y-103769737D01* +X138179177Y-103709394D01* +X138310287Y-103621789D01* +X138421787Y-103510289D01* +X138509392Y-103379179D01* +X138569735Y-103233497D01* +X138600498Y-103078842D01* +X138600498Y-102921158D01* +X138600498Y-102921155D01* +X138600497Y-102921153D01* +X138594474Y-102890874D01* +X138569735Y-102766503D01* +X138550953Y-102721158D01* +X138509395Y-102620827D01* +X138509388Y-102620814D01* +X138421787Y-102489711D01* +X138421784Y-102489707D01* +X138310290Y-102378213D01* +X138310286Y-102378210D01* +X138224895Y-102321153D01* +X141799500Y-102321153D01* +X141799500Y-102478846D01* +X141830261Y-102633489D01* +X141830264Y-102633501D01* +X141890602Y-102779172D01* +X141890609Y-102779185D01* +X141978210Y-102910288D01* +X141978213Y-102910292D01* +X142089707Y-103021786D01* +X142089711Y-103021789D01* +X142220814Y-103109390D01* +X142220827Y-103109397D01* +X142366498Y-103169735D01* +X142366503Y-103169737D01* +X142521153Y-103200499D01* +X142521156Y-103200500D01* +X142521158Y-103200500D01* +X142678844Y-103200500D01* +X142678845Y-103200499D01* +X142833497Y-103169737D01* +X142979179Y-103109394D01* +X143110289Y-103021789D01* +X143221789Y-102910289D01* +X143309394Y-102779179D01* +X143369737Y-102633497D01* +X143400500Y-102478842D01* +X143400500Y-102321158D01* +X143400500Y-102321155D01* +X143400499Y-102321153D01* +X143382419Y-102230261D01* +X143369737Y-102166503D01* +X143338298Y-102090602D01* +X143309397Y-102020827D01* +X143309390Y-102020814D01* +X143221789Y-101889711D01* +X143221786Y-101889707D01* +X143110292Y-101778213D01* +X143110288Y-101778210D01* +X142979185Y-101690609D01* +X142979172Y-101690602D01* +X142833501Y-101630264D01* +X142833489Y-101630261D01* +X142678845Y-101599500D01* +X142678842Y-101599500D01* +X142521158Y-101599500D01* +X142521155Y-101599500D01* +X142366510Y-101630261D01* +X142366498Y-101630264D01* +X142220827Y-101690602D01* +X142220814Y-101690609D01* +X142089711Y-101778210D01* +X142089707Y-101778213D01* +X141978213Y-101889707D01* +X141978210Y-101889711D01* +X141890609Y-102020814D01* +X141890602Y-102020827D01* +X141830264Y-102166498D01* +X141830261Y-102166510D01* +X141799500Y-102321153D01* +X138224895Y-102321153D01* +X138179183Y-102290609D01* +X138179170Y-102290602D01* +X138033499Y-102230264D01* +X138033487Y-102230261D01* +X137878843Y-102199500D01* +X137878840Y-102199500D01* +X137721156Y-102199500D01* +X137721153Y-102199500D01* +X137566508Y-102230261D01* +X137566496Y-102230264D01* +X137420825Y-102290602D01* +X137420812Y-102290609D01* +X137289709Y-102378210D01* +X137289705Y-102378213D01* +X137178211Y-102489707D01* +X137178208Y-102489711D01* +X137090607Y-102620814D01* +X137090600Y-102620827D01* +X137030262Y-102766498D01* +X137030259Y-102766510D01* +X136999498Y-102921153D01* +X123092084Y-102921153D01* +X123098107Y-102890875D01* +X123098107Y-102890874D01* +X123100500Y-102878844D01* +X123100500Y-102721155D01* +X123100499Y-102721153D01* +X123080543Y-102620827D01* +X123069737Y-102566503D01* +X123037929Y-102489711D01* +X123009397Y-102420827D01* +X123009390Y-102420814D01* +X122921789Y-102289711D01* +X122921786Y-102289707D01* +X122810292Y-102178213D01* +X122810288Y-102178210D01* +X122679185Y-102090609D01* +X122679172Y-102090602D01* +X122533501Y-102030264D01* +X122533489Y-102030261D01* +X122378845Y-101999500D01* +X122378842Y-101999500D01* +X122221158Y-101999500D01* +X122221155Y-101999500D01* +X122066510Y-102030261D01* +X122066498Y-102030264D01* +X121920827Y-102090602D01* +X121920814Y-102090609D01* +X121789711Y-102178210D01* +X121789707Y-102178213D01* +X121678213Y-102289707D01* +X121678210Y-102289711D01* +X121590609Y-102420814D01* +X121590602Y-102420827D01* +X121530264Y-102566498D01* +X121530261Y-102566510D01* +X121499500Y-102721153D01* +X120250500Y-102721153D01* +X120250500Y-100321153D01* +X125799500Y-100321153D01* +X125799500Y-100478846D01* +X125830261Y-100633489D01* +X125830264Y-100633501D01* +X125890602Y-100779172D01* +X125890609Y-100779185D01* +X125978210Y-100910288D01* +X125978213Y-100910292D01* +X126089707Y-101021786D01* +X126089711Y-101021789D01* +X126220814Y-101109390D01* +X126220827Y-101109397D01* +X126366498Y-101169735D01* +X126366503Y-101169737D01* +X126521153Y-101200499D01* +X126521156Y-101200500D01* +X126521158Y-101200500D01* +X126678844Y-101200500D01* +X126678845Y-101200499D01* +X126833497Y-101169737D01* +X126979179Y-101109394D01* +X127110289Y-101021789D01* +X127221789Y-100910289D01* +X127309394Y-100779179D01* +X127369737Y-100633497D01* +X127400500Y-100478842D01* +X127400500Y-100321158D01* +X127400500Y-100321155D01* +X127400499Y-100321153D01* +X127387716Y-100256891D01* +X127369737Y-100166503D01* +X127328314Y-100066498D01* +X127309397Y-100020827D01* +X127309393Y-100020820D01* +X127309389Y-100020814D01* +X127288800Y-99990000D01* +X127267923Y-99923324D01* +X127286407Y-99855944D01* +X127338386Y-99809253D01* +X127407356Y-99798077D01* +X127416084Y-99799490D01* +X127421158Y-99800500D01* +X127421160Y-99800500D01* +X127578844Y-99800500D01* +X127578845Y-99800499D01* +X127733497Y-99769737D01* +X127850923Y-99721097D01* +X127920392Y-99713629D01* +X127982871Y-99744904D01* +X128018523Y-99804993D01* +X128016029Y-99874818D01* +X128001478Y-99904549D01* +X127990608Y-99920816D01* +X127990602Y-99920827D01* +X127930264Y-100066498D01* +X127930261Y-100066510D01* +X127899500Y-100221153D01* +X127899500Y-100378846D01* +X127930261Y-100533489D01* +X127930264Y-100533501D01* +X127990602Y-100679172D01* +X127990609Y-100679185D01* +X128078210Y-100810288D01* +X128078213Y-100810292D01* +X128189707Y-100921786D01* +X128189711Y-100921789D01* +X128320814Y-101009390D01* +X128320827Y-101009397D01* +X128441518Y-101059388D01* +X128466503Y-101069737D01* +X128621153Y-101100499D01* +X128621156Y-101100500D01* +X128621158Y-101100500D01* +X128778844Y-101100500D01* +X128778845Y-101100499D01* +X128933497Y-101069737D01* +X129079179Y-101009394D01* +X129210289Y-100921789D01* +X129321789Y-100810289D01* +X129409394Y-100679179D01* +X129469737Y-100533497D01* +X129490555Y-100428841D01* +X129492084Y-100421153D01* +X130999500Y-100421153D01* +X130999500Y-100578846D01* +X131030261Y-100733489D01* +X131030264Y-100733501D01* +X131090602Y-100879172D01* +X131090609Y-100879185D01* +X131178210Y-101010288D01* +X131178213Y-101010292D01* +X131289707Y-101121786D01* +X131289711Y-101121789D01* +X131420814Y-101209390D01* +X131420827Y-101209397D01* +X131566498Y-101269735D01* +X131566503Y-101269737D01* +X131721153Y-101300499D01* +X131721156Y-101300500D01* +X131721158Y-101300500D01* +X131878844Y-101300500D01* +X131878845Y-101300499D01* +X132033497Y-101269737D01* +X132160626Y-101217079D01* +X132179172Y-101209397D01* +X132179172Y-101209396D01* +X132179179Y-101209394D01* +X132310289Y-101121789D01* +X132360469Y-101071609D01* +X132421792Y-101038123D01* +X132491483Y-101043107D01* +X132547417Y-101084978D01* +X132562712Y-101111837D01* +X132590602Y-101179172D01* +X132590609Y-101179185D01* +X132678210Y-101310288D01* +X132678213Y-101310292D01* +X132789707Y-101421786D01* +X132789711Y-101421789D01* +X132920814Y-101509390D01* +X132920827Y-101509397D01* +X133066498Y-101569735D01* +X133066503Y-101569737D01* +X133216131Y-101599500D01* +X133221153Y-101600499D01* +X133221156Y-101600500D01* +X133221158Y-101600500D01* +X133378844Y-101600500D01* +X133378845Y-101600499D01* +X133533497Y-101569737D01* +X133679179Y-101509394D01* +X133810289Y-101421789D01* +X133921789Y-101310289D01* +X134009394Y-101179179D01* +X134059013Y-101059388D01* +X135361265Y-101059388D01* +X135361265Y-101217081D01* +X135392026Y-101371724D01* +X135392029Y-101371736D01* +X135452367Y-101517407D01* +X135452374Y-101517420D01* +X135539975Y-101648523D01* +X135539978Y-101648527D01* +X135651472Y-101760021D01* +X135651476Y-101760024D01* +X135782579Y-101847625D01* +X135782592Y-101847632D01* +X135928263Y-101907970D01* +X135928268Y-101907972D01* +X136082918Y-101938734D01* +X136082921Y-101938735D01* +X136082923Y-101938735D01* +X136240609Y-101938735D01* +X136240610Y-101938734D01* +X136395262Y-101907972D01* +X136540944Y-101847629D01* +X136672054Y-101760024D01* +X136783554Y-101648524D01* +X136871159Y-101517414D01* +X136931502Y-101371732D01* +X136962265Y-101217077D01* +X136962265Y-101059393D01* +X136962265Y-101059390D01* +X136962264Y-101059388D01* +X136952498Y-101010292D01* +X136931502Y-100904738D01* +X136931500Y-100904733D01* +X136871162Y-100759062D01* +X136871155Y-100759049D01* +X136783554Y-100627946D01* +X136783551Y-100627942D01* +X136672057Y-100516448D01* +X136672053Y-100516445D01* +X136540950Y-100428844D01* +X136540937Y-100428837D01* +X136395266Y-100368499D01* +X136395256Y-100368496D01* +X136240610Y-100337735D01* +X136240607Y-100337735D01* +X136082923Y-100337735D01* +X136082920Y-100337735D01* +X135928275Y-100368496D01* +X135928263Y-100368499D01* +X135782592Y-100428837D01* +X135782579Y-100428844D01* +X135651476Y-100516445D01* +X135651472Y-100516448D01* +X135539978Y-100627942D01* +X135539975Y-100627946D01* +X135452374Y-100759049D01* +X135452367Y-100759062D01* +X135392029Y-100904733D01* +X135392026Y-100904745D01* +X135361265Y-101059388D01* +X134059013Y-101059388D01* +X134069737Y-101033497D01* +X134100433Y-100879179D01* +X134100500Y-100878844D01* +X134100500Y-100721155D01* +X134100499Y-100721153D01* +X134069738Y-100566510D01* +X134069737Y-100566503D01* +X134049003Y-100516446D01* +X134009397Y-100420827D01* +X134009390Y-100420814D01* +X133921789Y-100289711D01* +X133921786Y-100289707D01* +X133853232Y-100221153D01* +X139599500Y-100221153D01* +X139599500Y-100378846D01* +X139630261Y-100533489D01* +X139630264Y-100533501D01* +X139690602Y-100679172D01* +X139690609Y-100679185D01* +X139778210Y-100810288D01* +X139778213Y-100810292D01* +X139889707Y-100921786D01* +X139889711Y-100921789D01* +X140020814Y-101009390D01* +X140020827Y-101009397D01* +X140141518Y-101059388D01* +X140166503Y-101069737D01* +X140321153Y-101100499D01* +X140321156Y-101100500D01* +X140321158Y-101100500D01* +X140478844Y-101100500D01* +X140478845Y-101100499D01* +X140633497Y-101069737D01* +X140779179Y-101009394D01* +X140910289Y-100921789D01* +X141021789Y-100810289D01* +X141109394Y-100679179D01* +X141169737Y-100533497D01* +X141200500Y-100378842D01* +X141200500Y-100221158D01* +X141200500Y-100221155D01* +X141200499Y-100221153D01* +X141180543Y-100120827D01* +X141169737Y-100066503D01* +X141169735Y-100066498D01* +X141109397Y-99920827D01* +X141109390Y-99920814D01* +X141021789Y-99789711D01* +X141021786Y-99789707D01* +X140910292Y-99678213D01* +X140910288Y-99678210D01* +X140779185Y-99590609D01* +X140779172Y-99590602D01* +X140633501Y-99530264D01* +X140633489Y-99530261D01* +X140478845Y-99499500D01* +X140478842Y-99499500D01* +X140321158Y-99499500D01* +X140321155Y-99499500D01* +X140166510Y-99530261D01* +X140166498Y-99530264D01* +X140020827Y-99590602D01* +X140020814Y-99590609D01* +X139889711Y-99678210D01* +X139889707Y-99678213D01* +X139778213Y-99789707D01* +X139778210Y-99789711D01* +X139690609Y-99920814D01* +X139690602Y-99920827D01* +X139630264Y-100066498D01* +X139630261Y-100066510D01* +X139599500Y-100221153D01* +X133853232Y-100221153D01* +X133810292Y-100178213D01* +X133810288Y-100178210D01* +X133679185Y-100090609D01* +X133679172Y-100090602D01* +X133533501Y-100030264D01* +X133533489Y-100030261D01* +X133378845Y-99999500D01* +X133378842Y-99999500D01* +X133221158Y-99999500D01* +X133221155Y-99999500D01* +X133066510Y-100030261D01* +X133066498Y-100030264D01* +X132920827Y-100090602D01* +X132920814Y-100090609D01* +X132789711Y-100178210D01* +X132789706Y-100178214D01* +X132739528Y-100228392D01* +X132678205Y-100261876D01* +X132608513Y-100256891D01* +X132552580Y-100215020D01* +X132537289Y-100188166D01* +X132509394Y-100120821D01* +X132509390Y-100120814D01* +X132421789Y-99989711D01* +X132421786Y-99989707D01* +X132310292Y-99878213D01* +X132310288Y-99878210D01* +X132179185Y-99790609D01* +X132179172Y-99790602D01* +X132033501Y-99730264D01* +X132033489Y-99730261D01* +X131878845Y-99699500D01* +X131878842Y-99699500D01* +X131721158Y-99699500D01* +X131721155Y-99699500D01* +X131566510Y-99730261D01* +X131566498Y-99730264D01* +X131420827Y-99790602D01* +X131420814Y-99790609D01* +X131289711Y-99878210D01* +X131289707Y-99878213D01* +X131178213Y-99989707D01* +X131178210Y-99989711D01* +X131090609Y-100120814D01* +X131090602Y-100120827D01* +X131030264Y-100266498D01* +X131030261Y-100266510D01* +X130999500Y-100421153D01* +X129492084Y-100421153D01* +X129498107Y-100390875D01* +X129498107Y-100390874D01* +X129500500Y-100378844D01* +X129500500Y-100221155D01* +X129500499Y-100221153D01* +X129480543Y-100120827D01* +X129469737Y-100066503D01* +X129469735Y-100066498D01* +X129409397Y-99920827D01* +X129409390Y-99920814D01* +X129321789Y-99789711D01* +X129321786Y-99789707D01* +X129210292Y-99678213D01* +X129210288Y-99678210D01* +X129079185Y-99590609D01* +X129079172Y-99590602D01* +X128933501Y-99530264D01* +X128933489Y-99530261D01* +X128778845Y-99499500D01* +X128778842Y-99499500D01* +X128621158Y-99499500D01* +X128621155Y-99499500D01* +X128466510Y-99530261D01* +X128466503Y-99530263D01* +X128349075Y-99578902D01* +X128279606Y-99586370D01* +X128217127Y-99555094D01* +X128181475Y-99495005D01* +X128183970Y-99425180D01* +X128198525Y-99395445D01* +X128209390Y-99379185D01* +X128209390Y-99379184D01* +X128209394Y-99379179D01* +X128269737Y-99233497D01* +X128300500Y-99078842D01* +X128300500Y-98921158D01* +X128300500Y-98921155D01* +X128300499Y-98921153D01* +X135099500Y-98921153D01* +X135099500Y-99078846D01* +X135130261Y-99233489D01* +X135130264Y-99233501D01* +X135190602Y-99379172D01* +X135190609Y-99379185D01* +X135278210Y-99510288D01* +X135278213Y-99510292D01* +X135389707Y-99621786D01* +X135389711Y-99621789D01* +X135520814Y-99709390D01* +X135520827Y-99709397D01* +X135606550Y-99744904D01* +X135666503Y-99769737D01* +X135808977Y-99798077D01* +X135821153Y-99800499D01* +X135821156Y-99800500D01* +X135821158Y-99800500D01* +X135978844Y-99800500D01* +X135978845Y-99800499D01* +X136133497Y-99769737D01* +X136279179Y-99709394D01* +X136410289Y-99621789D01* +X136521789Y-99510289D01* +X136609394Y-99379179D01* +X136669737Y-99233497D01* +X136700500Y-99078842D01* +X136700500Y-98921158D01* +X136700500Y-98921155D01* +X136700499Y-98921153D01* +X136689455Y-98865633D01* +X136669737Y-98766503D01* +X136633427Y-98678842D01* +X136609397Y-98620827D01* +X136609390Y-98620814D01* +X136521789Y-98489711D01* +X136521786Y-98489707D01* +X136410292Y-98378213D01* +X136410288Y-98378210D01* +X136279185Y-98290609D01* +X136279172Y-98290602D01* +X136133501Y-98230264D01* +X136133489Y-98230261D01* +X135978845Y-98199500D01* +X135978842Y-98199500D01* +X135821158Y-98199500D01* +X135821155Y-98199500D01* +X135666510Y-98230261D01* +X135666498Y-98230264D01* +X135520827Y-98290602D01* +X135520814Y-98290609D01* +X135389711Y-98378210D01* +X135389707Y-98378213D01* +X135278213Y-98489707D01* +X135278210Y-98489711D01* +X135190609Y-98620814D01* +X135190602Y-98620827D01* +X135130264Y-98766498D01* +X135130261Y-98766510D01* +X135099500Y-98921153D01* +X128300499Y-98921153D01* +X128289455Y-98865633D01* +X128269737Y-98766503D01* +X128230572Y-98671951D01* +X128223104Y-98602483D01* +X128254379Y-98540004D01* +X128314468Y-98504352D01* +X128345134Y-98500500D01* +X128378844Y-98500500D01* +X128378845Y-98500499D01* +X128533497Y-98469737D01* +X128679179Y-98409394D01* +X128810289Y-98321789D01* +X128921789Y-98210289D01* +X129009394Y-98079179D01* +X129069737Y-97933497D01* +X129100500Y-97778842D01* +X129100500Y-97621158D01* +X129100500Y-97621155D01* +X129100499Y-97621153D01* +X129086136Y-97548946D01* +X129069737Y-97466503D01* +X129060732Y-97444762D01* +X129057544Y-97415113D01* +X129051824Y-97385843D01* +X129053849Y-97380745D01* +X129053263Y-97375293D01* +X129066610Y-97348629D01* +X129067594Y-97346153D01* +X130049500Y-97346153D01* +X130049500Y-97503846D01* +X130080261Y-97658489D01* +X130080264Y-97658501D01* +X130140602Y-97804172D01* +X130140609Y-97804185D01* +X130228210Y-97935288D01* +X130228213Y-97935292D01* +X130339707Y-98046786D01* +X130339711Y-98046789D01* +X130470814Y-98134390D01* +X130470827Y-98134397D01* +X130579710Y-98179497D01* +X130616503Y-98194737D01* +X130751019Y-98221494D01* +X130771153Y-98225499D01* +X130771156Y-98225500D01* +X130771158Y-98225500D01* +X130928844Y-98225500D01* +X130928845Y-98225499D01* +X131083497Y-98194737D01* +X131229179Y-98134394D01* +X131360289Y-98046789D01* +X131471789Y-97935289D01* +X131559394Y-97804179D01* +X131570625Y-97777066D01* +X131601059Y-97703589D01* +X131619737Y-97658497D01* +X131650500Y-97503842D01* +X131650500Y-97346158D01* +X131650500Y-97346155D01* +X131650499Y-97346153D01* +X131623474Y-97210292D01* +X131619737Y-97191503D01* +X131618993Y-97189707D01* +X131559397Y-97045827D01* +X131559390Y-97045814D01* +X131471789Y-96914711D01* +X131471786Y-96914707D01* +X131360292Y-96803213D01* +X131360288Y-96803210D01* +X131229185Y-96715609D01* +X131229172Y-96715602D01* +X131083501Y-96655264D01* +X131083489Y-96655261D01* +X130928845Y-96624500D01* +X130928842Y-96624500D01* +X130771158Y-96624500D01* +X130771155Y-96624500D01* +X130616510Y-96655261D01* +X130616498Y-96655264D01* +X130470827Y-96715602D01* +X130470814Y-96715609D01* +X130339711Y-96803210D01* +X130339707Y-96803213D01* +X130228213Y-96914707D01* +X130228210Y-96914711D01* +X130140609Y-97045814D01* +X130140602Y-97045827D01* +X130080264Y-97191498D01* +X130080261Y-97191510D01* +X130049500Y-97346153D01* +X129067594Y-97346153D01* +X129077624Y-97320911D01* +X129082967Y-97315952D01* +X129084539Y-97312814D01* +X129103105Y-97296489D01* +X129104720Y-97295332D01* +X129164669Y-97255276D01* +X129255276Y-97164669D01* +X129326465Y-97058127D01* +X129375501Y-96939744D01* +X129387658Y-96878628D01* +X129400500Y-96814071D01* +X129400500Y-96685928D01* +X129375502Y-96560261D01* +X129375501Y-96560260D01* +X129375501Y-96560256D01* +X129336665Y-96466498D01* +X129326466Y-96441875D01* +X129326461Y-96441866D01* +X129255276Y-96335331D01* +X129251411Y-96330621D01* +X129253045Y-96329279D01* +X129224148Y-96276389D01* +X129229114Y-96206696D01* +X129252514Y-96170284D01* +X129251411Y-96169379D01* +X129255271Y-96164673D01* +X129255276Y-96164669D01* +X129326465Y-96058127D01* +X129375501Y-95939744D01* +X129383682Y-95898615D01* +X129400500Y-95814071D01* +X129400500Y-95685928D01* +X129375502Y-95560261D01* +X129375501Y-95560260D01* +X129375501Y-95560256D01* +X129326465Y-95441873D01* +X129326464Y-95441872D01* +X129326461Y-95441866D01* +X129255276Y-95335331D01* +X129255273Y-95335327D01* +X129185770Y-95265824D01* +X129161378Y-95221153D01* +X131199500Y-95221153D01* +X131199500Y-95378846D01* +X131230261Y-95533489D01* +X131230264Y-95533501D01* +X131290602Y-95679172D01* +X131290609Y-95679185D01* +X131378210Y-95810288D01* +X131378213Y-95810292D01* +X131489707Y-95921786D01* +X131489711Y-95921789D01* +X131620814Y-96009390D01* +X131620827Y-96009397D01* +X131738488Y-96058133D01* +X131766503Y-96069737D01* +X131921153Y-96100499D01* +X131921156Y-96100500D01* +X131921158Y-96100500D01* +X132078844Y-96100500D01* +X132078845Y-96100499D01* +X132233497Y-96069737D01* +X132379179Y-96009394D01* +X132510289Y-95921789D01* +X132621789Y-95810289D01* +X132709394Y-95679179D01* +X132709395Y-95679176D01* +X132709397Y-95679173D01* +X132712719Y-95671153D01* +X134449500Y-95671153D01* +X134449500Y-95828846D01* +X134480261Y-95983489D01* +X134480264Y-95983501D01* +X134540602Y-96129172D01* +X134540609Y-96129185D01* +X134628210Y-96260288D01* +X134628213Y-96260292D01* +X134739707Y-96371786D01* +X134739710Y-96371788D01* +X134739711Y-96371789D01* +X134765219Y-96388833D01* +X134777289Y-96396898D01* +X134822093Y-96450511D01* +X134830800Y-96519836D01* +X134800645Y-96582863D01* +X134777289Y-96603102D01* +X134739707Y-96628213D01* +X134628213Y-96739707D01* +X134628210Y-96739711D01* +X134540609Y-96870814D01* +X134540602Y-96870827D01* +X134480264Y-97016498D01* +X134480261Y-97016510D01* +X134449500Y-97171153D01* +X134449500Y-97328846D01* +X134480261Y-97483489D01* +X134480264Y-97483501D01* +X134540602Y-97629172D01* +X134540609Y-97629185D01* +X134628210Y-97760288D01* +X134628213Y-97760292D01* +X134739707Y-97871786D01* +X134739711Y-97871789D01* +X134870814Y-97959390D01* +X134870827Y-97959397D01* +X135016498Y-98019735D01* +X135016503Y-98019737D01* +X135152487Y-98046786D01* +X135171153Y-98050499D01* +X135171156Y-98050500D01* +X135171158Y-98050500D01* +X135328844Y-98050500D01* +X135328845Y-98050499D01* +X135483497Y-98019737D01* +X135629179Y-97959394D01* +X135760289Y-97871789D01* +X135871789Y-97760289D01* +X135931348Y-97671153D01* +X136699500Y-97671153D01* +X136699500Y-97828846D01* +X136730261Y-97983489D01* +X136730264Y-97983501D01* +X136790602Y-98129172D01* +X136790609Y-98129185D01* +X136878210Y-98260288D01* +X136878213Y-98260292D01* +X136989707Y-98371786D01* +X136989711Y-98371789D01* +X137120814Y-98459390D01* +X137120827Y-98459397D01* +X137220060Y-98500500D01* +X137266503Y-98519737D01* +X137421153Y-98550499D01* +X137421156Y-98550500D01* +X137421158Y-98550500D01* +X137578844Y-98550500D01* +X137578845Y-98550499D01* +X137733497Y-98519737D01* +X137879179Y-98459394D01* +X138010289Y-98371789D01* +X138121789Y-98260289D01* +X138197966Y-98146282D01* +X139085387Y-98146282D01* +X139085387Y-98303975D01* +X139116148Y-98458618D01* +X139116151Y-98458630D01* +X139176489Y-98604301D01* +X139176496Y-98604314D01* +X139264097Y-98735417D01* +X139264100Y-98735421D01* +X139375594Y-98846915D01* +X139375598Y-98846918D01* +X139506701Y-98934519D01* +X139506714Y-98934526D01* +X139614532Y-98979185D01* +X139652390Y-98994866D01* +X139807040Y-99025628D01* +X139807043Y-99025629D01* +X139807045Y-99025629D01* +X139964731Y-99025629D01* +X139964732Y-99025628D01* +X140119384Y-98994866D01* +X140265066Y-98934523D01* +X140396176Y-98846918D01* +X140507676Y-98735418D01* +X140595281Y-98604308D01* +X140655624Y-98458626D01* +X140686387Y-98303971D01* +X140686387Y-98146287D01* +X140686387Y-98146284D01* +X140686386Y-98146282D01* +X140676285Y-98095496D01* +X140672684Y-98077392D01* +X146233858Y-98077392D01* +X146233858Y-98235085D01* +X146264619Y-98389728D01* +X146264622Y-98389740D01* +X146324960Y-98535411D01* +X146324967Y-98535424D01* +X146412568Y-98666527D01* +X146412571Y-98666531D01* +X146524065Y-98778025D01* +X146524069Y-98778028D01* +X146655172Y-98865629D01* +X146655185Y-98865636D01* +X146789217Y-98921153D01* +X146800861Y-98925976D01* +X146860027Y-98937745D01* +X146928316Y-98951329D01* +X146990227Y-98983714D01* +X147007227Y-99004055D01* +X147078210Y-99110288D01* +X147078213Y-99110292D01* +X147189707Y-99221786D01* +X147189711Y-99221789D01* +X147320814Y-99309390D01* +X147320827Y-99309397D01* +X147466498Y-99369735D01* +X147466503Y-99369737D01* +X147595745Y-99395445D01* +X147621153Y-99400499D01* +X147621156Y-99400500D01* +X147621158Y-99400500D01* +X147778844Y-99400500D01* +X147778845Y-99400499D01* +X147933497Y-99369737D01* +X148079179Y-99309394D01* +X148210289Y-99221789D01* +X148321789Y-99110289D01* +X148409394Y-98979179D01* +X148469737Y-98833497D01* +X148500500Y-98678842D01* +X148500500Y-98521158D01* +X148500500Y-98521155D01* +X148500499Y-98521153D01* +X148488062Y-98458630D01* +X148469737Y-98366503D01* +X148451215Y-98321786D01* +X148409397Y-98220827D01* +X148409390Y-98220814D01* +X148321789Y-98089711D01* +X148321786Y-98089707D01* +X148210292Y-97978213D01* +X148210288Y-97978210D01* +X148079185Y-97890609D01* +X148079172Y-97890602D01* +X147933501Y-97830264D01* +X147933491Y-97830261D01* +X147806040Y-97804909D01* +X147744129Y-97772524D01* +X147727130Y-97752183D01* +X147656147Y-97645950D01* +X147652282Y-97641240D01* +X147654018Y-97639815D01* +X147625341Y-97587335D01* +X147630304Y-97517642D01* +X147658816Y-97473261D01* +X147671789Y-97460289D01* +X147759394Y-97329179D01* +X147762854Y-97320827D01* +X147790005Y-97255276D01* +X147819737Y-97183497D01* +X147850500Y-97028842D01* +X147850500Y-96871158D01* +X147850500Y-96871155D01* +X147850499Y-96871153D01* +X147840402Y-96820391D01* +X147819737Y-96716503D01* +X147819367Y-96715609D01* +X147759397Y-96570827D01* +X147759390Y-96570814D01* +X147671789Y-96439711D01* +X147671786Y-96439707D01* +X147560292Y-96328213D01* +X147560288Y-96328210D01* +X147429185Y-96240609D01* +X147429172Y-96240602D01* +X147283501Y-96180264D01* +X147283489Y-96180261D01* +X147128845Y-96149500D01* +X147128842Y-96149500D01* +X146971158Y-96149500D01* +X146971155Y-96149500D01* +X146816510Y-96180261D01* +X146816498Y-96180264D01* +X146670827Y-96240602D01* +X146670814Y-96240609D01* +X146539711Y-96328210D01* +X146539707Y-96328213D01* +X146428213Y-96439707D01* +X146428210Y-96439711D01* +X146340609Y-96570814D01* +X146340602Y-96570827D01* +X146280264Y-96716498D01* +X146280261Y-96716510D01* +X146249500Y-96871153D01* +X146249500Y-97028846D01* +X146280261Y-97183489D01* +X146280264Y-97183501D01* +X146340602Y-97329172D01* +X146340609Y-97329185D01* +X146428210Y-97460288D01* +X146432076Y-97464999D01* +X146430344Y-97466419D01* +X146459023Y-97518940D01* +X146454039Y-97588632D01* +X146425543Y-97632974D01* +X146412572Y-97645946D01* +X146412566Y-97645953D01* +X146324967Y-97777053D01* +X146324960Y-97777066D01* +X146264622Y-97922737D01* +X146264619Y-97922749D01* +X146233858Y-98077392D01* +X140672684Y-98077392D01* +X140655625Y-97991637D01* +X140655624Y-97991636D01* +X140655624Y-97991632D01* +X140650065Y-97978211D01* +X140595284Y-97845956D01* +X140595277Y-97845943D01* +X140507676Y-97714840D01* +X140507673Y-97714836D01* +X140396179Y-97603342D01* +X140396175Y-97603339D01* +X140265072Y-97515738D01* +X140265059Y-97515731D01* +X140119388Y-97455393D01* +X140119376Y-97455390D01* +X139964732Y-97424629D01* +X139964729Y-97424629D01* +X139807045Y-97424629D01* +X139807042Y-97424629D01* +X139652397Y-97455390D01* +X139652385Y-97455393D01* +X139506714Y-97515731D01* +X139506701Y-97515738D01* +X139375598Y-97603339D01* +X139375594Y-97603342D01* +X139264100Y-97714836D01* +X139264097Y-97714840D01* +X139176496Y-97845943D01* +X139176489Y-97845956D01* +X139116151Y-97991627D01* +X139116148Y-97991639D01* +X139085387Y-98146282D01* +X138197966Y-98146282D01* +X138209394Y-98129179D01* +X138269737Y-97983497D01* +X138300500Y-97828842D01* +X138300500Y-97671158D01* +X138300500Y-97671155D01* +X138300499Y-97671153D01* +X138276190Y-97548944D01* +X138269737Y-97516503D01* +X138264493Y-97503842D01* +X138209397Y-97370827D01* +X138209390Y-97370814D01* +X138121789Y-97239711D01* +X138121786Y-97239707D01* +X138010292Y-97128213D01* +X138010288Y-97128210D01* +X137879185Y-97040609D01* +X137879172Y-97040602D01* +X137733501Y-96980264D01* +X137733489Y-96980261D01* +X137578845Y-96949500D01* +X137578842Y-96949500D01* +X137421158Y-96949500D01* +X137421155Y-96949500D01* +X137266510Y-96980261D01* +X137266498Y-96980264D01* +X137120827Y-97040602D01* +X137120814Y-97040609D01* +X136989711Y-97128210D01* +X136989707Y-97128213D01* +X136878213Y-97239707D01* +X136878210Y-97239711D01* +X136790609Y-97370814D01* +X136790602Y-97370827D01* +X136730264Y-97516498D01* +X136730261Y-97516510D01* +X136699500Y-97671153D01* +X135931348Y-97671153D01* +X135959394Y-97629179D01* +X136019737Y-97483497D01* +X136050500Y-97328842D01* +X136050500Y-97171158D01* +X136050500Y-97171155D01* +X136050499Y-97171153D01* +X136032204Y-97079179D01* +X136019737Y-97016503D01* +X136019735Y-97016498D01* +X135959397Y-96870827D01* +X135959390Y-96870814D01* +X135871789Y-96739711D01* +X135871786Y-96739707D01* +X135760292Y-96628213D01* +X135760284Y-96628207D01* +X135722712Y-96603102D01* +X135677906Y-96549490D01* +X135669199Y-96480165D01* +X135699353Y-96417138D01* +X135722712Y-96396898D01* +X135749279Y-96379145D01* +X135760289Y-96371789D01* +X135871789Y-96260289D01* +X135959394Y-96129179D01* +X136019737Y-95983497D01* +X136050500Y-95828842D01* +X136050500Y-95671158D01* +X136050500Y-95671155D01* +X136050499Y-95671153D01* +X136035330Y-95594893D01* +X136019737Y-95516503D01* +X136006062Y-95483489D01* +X135959397Y-95370827D01* +X135959390Y-95370814D01* +X135871789Y-95239711D01* +X135871786Y-95239707D01* +X135760292Y-95128213D01* +X135760288Y-95128210D01* +X135629185Y-95040609D01* +X135629172Y-95040602D01* +X135483501Y-94980264D01* +X135483489Y-94980261D01* +X135328845Y-94949500D01* +X135328842Y-94949500D01* +X135171158Y-94949500D01* +X135171155Y-94949500D01* +X135016510Y-94980261D01* +X135016498Y-94980264D01* +X134870827Y-95040602D01* +X134870814Y-95040609D01* +X134739711Y-95128210D01* +X134739707Y-95128213D01* +X134628213Y-95239707D01* +X134628210Y-95239711D01* +X134540609Y-95370814D01* +X134540602Y-95370827D01* +X134480264Y-95516498D01* +X134480261Y-95516510D01* +X134449500Y-95671153D01* +X132712719Y-95671153D01* +X132734895Y-95617614D01* +X132734895Y-95617613D01* +X132769737Y-95533497D01* +X132800500Y-95378842D01* +X132800500Y-95221158D01* +X132800500Y-95221155D01* +X132800499Y-95221153D01* +X132782012Y-95128213D01* +X132769737Y-95066503D01* +X132769735Y-95066498D01* +X132709397Y-94920827D01* +X132709390Y-94920814D01* +X132651354Y-94833957D01* +X132621789Y-94789711D01* +X132621786Y-94789707D01* +X132603232Y-94771153D01* +X138699500Y-94771153D01* +X138699500Y-94928846D01* +X138730261Y-95083489D01* +X138730264Y-95083501D01* +X138790602Y-95229172D01* +X138790609Y-95229185D01* +X138878210Y-95360288D01* +X138878213Y-95360292D01* +X138989707Y-95471786D01* +X138989711Y-95471789D01* +X139120814Y-95559390D01* +X139120827Y-95559397D01* +X139266498Y-95619735D01* +X139266503Y-95619737D01* +X139421153Y-95650499D01* +X139421156Y-95650500D01* +X139421158Y-95650500D01* +X139578844Y-95650500D01* +X139578845Y-95650499D01* +X139733497Y-95619737D01* +X139877098Y-95560256D01* +X139879172Y-95559397D01* +X139879172Y-95559396D01* +X139879179Y-95559394D01* +X140010289Y-95471789D01* +X140121789Y-95360289D01* +X140209394Y-95229179D01* +X140210416Y-95226713D01* +X140269735Y-95083501D01* +X140269737Y-95083497D01* +X140300500Y-94928842D01* +X140300500Y-94771158D01* +X140300500Y-94771155D01* +X140300499Y-94771153D01* +X140282012Y-94678213D01* +X140269737Y-94616503D01* +X140269735Y-94616498D01* +X140209397Y-94470827D01* +X140209390Y-94470814D01* +X140121789Y-94339711D01* +X140121786Y-94339707D01* +X140010292Y-94228213D01* +X140010288Y-94228210D01* +X139879185Y-94140609D01* +X139879172Y-94140602D01* +X139733501Y-94080264D01* +X139733489Y-94080261D01* +X139578845Y-94049500D01* +X139578842Y-94049500D01* +X139421158Y-94049500D01* +X139421155Y-94049500D01* +X139266510Y-94080261D01* +X139266498Y-94080264D01* +X139120827Y-94140602D01* +X139120814Y-94140609D01* +X138989711Y-94228210D01* +X138989707Y-94228213D01* +X138878213Y-94339707D01* +X138878210Y-94339711D01* +X138790609Y-94470814D01* +X138790602Y-94470827D01* +X138730264Y-94616498D01* +X138730261Y-94616510D01* +X138699500Y-94771153D01* +X132603232Y-94771153D01* +X132510292Y-94678213D01* +X132510288Y-94678210D01* +X132379185Y-94590609D01* +X132379172Y-94590602D01* +X132233501Y-94530264D01* +X132233489Y-94530261D01* +X132078845Y-94499500D01* +X132078842Y-94499500D01* +X131921158Y-94499500D01* +X131921155Y-94499500D01* +X131766510Y-94530261D01* +X131766498Y-94530264D01* +X131620827Y-94590602D01* +X131620814Y-94590609D01* +X131489711Y-94678210D01* +X131489707Y-94678213D01* +X131378213Y-94789707D01* +X131378210Y-94789711D01* +X131290609Y-94920814D01* +X131290602Y-94920827D01* +X131230264Y-95066498D01* +X131230261Y-95066510D01* +X131199500Y-95221153D01* +X129161378Y-95221153D01* +X129152285Y-95204501D01* +X129150049Y-95165982D01* +X129150299Y-95163445D01* +X129150299Y-95005759D01* +X129150298Y-95005757D01* +X129145227Y-94980263D01* +X129119536Y-94851107D01* +X129094105Y-94789711D01* +X129059196Y-94705431D01* +X129059189Y-94705418D01* +X128971588Y-94574315D01* +X128971585Y-94574311D01* +X128860091Y-94462817D01* +X128860087Y-94462814D01* +X128728984Y-94375213D01* +X128728971Y-94375206D01* +X128583300Y-94314868D01* +X128583288Y-94314865D01* +X128428644Y-94284104D01* +X128428641Y-94284104D01* +X128270957Y-94284104D01* +X128270954Y-94284104D01* +X128116309Y-94314865D01* +X128116297Y-94314868D01* +X127970626Y-94375206D01* +X127970613Y-94375213D01* +X127839510Y-94462814D01* +X127839506Y-94462817D01* +X127728012Y-94574311D01* +X127728009Y-94574315D01* +X127640408Y-94705418D01* +X127640401Y-94705431D01* +X127580063Y-94851102D01* +X127580060Y-94851114D01* +X127549299Y-95005757D01* +X127549299Y-95163450D01* +X127580060Y-95318093D01* +X127580063Y-95318105D01* +X127640401Y-95463776D01* +X127640408Y-95463789D01* +X127728009Y-95594892D01* +X127728012Y-95594896D01* +X127839506Y-95706390D01* +X127839510Y-95706393D01* +X127970616Y-95793996D01* +X127970618Y-95793996D01* +X127970620Y-95793998D01* +X128045486Y-95825008D01* +X128099890Y-95868848D01* +X128119651Y-95915375D01* +X128124498Y-95939741D01* +X128124498Y-95939742D01* +X128173533Y-96058124D01* +X128173538Y-96058133D01* +X128244723Y-96164668D01* +X128248589Y-96169379D01* +X128246958Y-96170716D01* +X128275858Y-96223642D01* +X128270874Y-96293334D01* +X128247489Y-96329719D01* +X128248589Y-96330621D01* +X128244723Y-96335331D01* +X128173538Y-96441866D01* +X128173533Y-96441875D01* +X128124499Y-96560255D01* +X128124497Y-96560261D01* +X128099500Y-96685928D01* +X128099500Y-96814071D01* +X128100097Y-96820134D01* +X128097477Y-96820391D01* +X128092238Y-96878628D01* +X128049349Y-96933785D01* +X128024323Y-96947734D01* +X127920823Y-96990604D01* +X127920814Y-96990609D01* +X127789711Y-97078210D01* +X127789707Y-97078213D01* +X127678213Y-97189707D01* +X127678210Y-97189711D01* +X127590609Y-97320814D01* +X127590602Y-97320827D01* +X127530264Y-97466498D01* +X127530261Y-97466510D01* +X127499500Y-97621153D01* +X127499500Y-97778846D01* +X127528125Y-97922749D01* +X127530263Y-97933497D01* +X127549687Y-97980392D01* +X127569427Y-98028047D01* +X127576896Y-98097517D01* +X127545621Y-98159996D01* +X127485532Y-98195648D01* +X127454866Y-98199500D01* +X127421155Y-98199500D01* +X127266510Y-98230261D01* +X127266498Y-98230264D01* +X127120827Y-98290602D01* +X127120814Y-98290609D01* +X126989711Y-98378210D01* +X126989707Y-98378213D01* +X126878213Y-98489707D01* +X126878210Y-98489711D01* +X126790609Y-98620814D01* +X126790602Y-98620827D01* +X126730264Y-98766498D01* +X126730261Y-98766510D01* +X126699500Y-98921153D01* +X126699500Y-99078846D01* +X126730261Y-99233489D01* +X126730264Y-99233501D01* +X126790602Y-99379172D01* +X126790609Y-99379185D01* +X126811198Y-99409998D01* +X126832076Y-99476676D01* +X126813592Y-99544056D01* +X126761613Y-99590746D01* +X126692643Y-99601922D01* +X126683909Y-99600507D01* +X126678846Y-99599500D01* +X126678842Y-99599500D01* +X126521158Y-99599500D01* +X126521155Y-99599500D01* +X126366510Y-99630261D01* +X126366498Y-99630264D01* +X126220827Y-99690602D01* +X126220814Y-99690609D01* +X126089711Y-99778210D01* +X126089707Y-99778213D01* +X125978213Y-99889707D01* +X125978210Y-99889711D01* +X125890609Y-100020814D01* +X125890602Y-100020827D01* +X125830264Y-100166498D01* +X125830261Y-100166510D01* +X125799500Y-100321153D01* +X120250500Y-100321153D01* +X120250500Y-96621153D01* +X120999500Y-96621153D01* +X120999500Y-96778846D01* +X121030261Y-96933489D01* +X121030264Y-96933501D01* +X121090602Y-97079172D01* +X121090609Y-97079185D01* +X121178210Y-97210288D01* +X121178213Y-97210292D01* +X121289707Y-97321786D01* +X121289711Y-97321789D01* +X121420814Y-97409390D01* +X121420827Y-97409397D01* +X121558683Y-97466498D01* +X121566503Y-97469737D01* +X121721153Y-97500499D01* +X121721156Y-97500500D01* +X121721158Y-97500500D01* +X121878844Y-97500500D01* +X121878845Y-97500499D01* +X122033497Y-97469737D01* +X122179179Y-97409394D01* +X122206329Y-97391253D01* +X125349500Y-97391253D01* +X125349500Y-97548946D01* +X125380261Y-97703589D01* +X125380264Y-97703601D01* +X125440602Y-97849272D01* +X125440609Y-97849285D01* +X125528210Y-97980388D01* +X125528213Y-97980392D01* +X125639707Y-98091886D01* +X125639711Y-98091889D01* +X125770814Y-98179490D01* +X125770827Y-98179497D01* +X125916498Y-98239835D01* +X125916503Y-98239837D01* +X126019337Y-98260292D01* +X126071153Y-98270599D01* +X126071156Y-98270600D01* +X126071158Y-98270600D01* +X126228844Y-98270600D01* +X126228845Y-98270599D01* +X126383497Y-98239837D01* +X126529179Y-98179494D01* +X126660289Y-98091889D01* +X126771789Y-97980389D01* +X126859394Y-97849279D01* +X126860771Y-97845956D01* +X126873067Y-97816266D01* +X126919737Y-97703597D01* +X126950500Y-97548942D01* +X126950500Y-97391258D01* +X126950500Y-97391255D01* +X126950499Y-97391253D01* +X126946433Y-97370814D01* +X126919737Y-97236603D01* +X126908839Y-97210292D01* +X126859397Y-97090927D01* +X126859390Y-97090914D01* +X126771789Y-96959811D01* +X126771786Y-96959807D01* +X126660292Y-96848313D01* +X126660288Y-96848310D01* +X126529185Y-96760709D01* +X126529172Y-96760702D01* +X126383501Y-96700364D01* +X126383489Y-96700361D01* +X126228845Y-96669600D01* +X126228842Y-96669600D01* +X126071158Y-96669600D01* +X126071155Y-96669600D01* +X125916510Y-96700361D01* +X125916498Y-96700364D01* +X125770827Y-96760702D01* +X125770814Y-96760709D01* +X125639711Y-96848310D01* +X125639707Y-96848313D01* +X125528213Y-96959807D01* +X125528210Y-96959811D01* +X125440609Y-97090914D01* +X125440602Y-97090927D01* +X125380264Y-97236598D01* +X125380261Y-97236610D01* +X125349500Y-97391253D01* +X122206329Y-97391253D01* +X122310289Y-97321789D01* +X122319264Y-97312814D01* +X122334594Y-97297485D01* +X122421786Y-97210292D01* +X122421789Y-97210289D01* +X122509394Y-97079179D01* +X122518112Y-97058133D01* +X122535357Y-97016498D01* +X122569737Y-96933497D01* +X122600500Y-96778842D01* +X122600500Y-96621158D01* +X122600500Y-96621155D01* +X122600499Y-96621153D01* +X122596908Y-96603102D01* +X122569737Y-96466503D01* +X122559532Y-96441866D01* +X122509397Y-96320827D01* +X122509390Y-96320814D01* +X122421789Y-96189711D01* +X122421786Y-96189707D01* +X122310292Y-96078213D01* +X122310288Y-96078210D01* +X122179185Y-95990609D01* +X122179172Y-95990602D01* +X122033501Y-95930264D01* +X122033489Y-95930261D01* +X121878845Y-95899500D01* +X121878842Y-95899500D01* +X121721158Y-95899500D01* +X121721155Y-95899500D01* +X121566510Y-95930261D01* +X121566498Y-95930264D01* +X121420827Y-95990602D01* +X121420814Y-95990609D01* +X121289711Y-96078210D01* +X121289707Y-96078213D01* +X121178213Y-96189707D01* +X121178210Y-96189711D01* +X121090609Y-96320814D01* +X121090602Y-96320827D01* +X121030264Y-96466498D01* +X121030261Y-96466510D01* +X120999500Y-96621153D01* +X120250500Y-96621153D01* +X120250500Y-95171153D01* +X122949500Y-95171153D01* +X122949500Y-95328846D01* +X122980261Y-95483489D01* +X122980264Y-95483501D01* +X123040602Y-95629172D01* +X123040609Y-95629185D01* +X123128210Y-95760288D01* +X123128213Y-95760292D01* +X123239707Y-95871786D01* +X123239711Y-95871789D01* +X123370814Y-95959390D01* +X123370827Y-95959397D01* +X123508683Y-96016498D01* +X123516503Y-96019737D01* +X123671153Y-96050499D01* +X123671156Y-96050500D01* +X123825500Y-96050500D01* +X123892539Y-96070185D01* +X123938294Y-96122989D01* +X123949500Y-96174500D01* +X123949500Y-96328846D01* +X123980261Y-96483489D01* +X123980264Y-96483501D01* +X124040602Y-96629172D01* +X124040609Y-96629185D01* +X124128210Y-96760288D01* +X124128213Y-96760292D01* +X124239707Y-96871786D01* +X124239711Y-96871789D01* +X124370814Y-96959390D01* +X124370827Y-96959397D01* +X124446181Y-96990609D01* +X124516503Y-97019737D01* +X124671153Y-97050499D01* +X124671156Y-97050500D01* +X124671158Y-97050500D01* +X124828844Y-97050500D01* +X124828845Y-97050499D01* +X124983497Y-97019737D01* +X125096166Y-96973067D01* +X125129172Y-96959397D01* +X125129172Y-96959396D01* +X125129179Y-96959394D01* +X125260289Y-96871789D01* +X125371789Y-96760289D01* +X125459394Y-96629179D01* +X125462719Y-96621153D01* +X125483569Y-96570814D01* +X125519737Y-96483497D01* +X125550500Y-96328842D01* +X125550500Y-96171158D01* +X125550500Y-96171155D01* +X125550499Y-96171153D01* +X125542148Y-96129172D01* +X125519737Y-96016503D01* +X125516791Y-96009390D01* +X125459397Y-95870827D01* +X125459390Y-95870814D01* +X125371789Y-95739711D01* +X125371786Y-95739707D01* +X125260292Y-95628213D01* +X125260288Y-95628210D01* +X125129185Y-95540609D01* +X125129172Y-95540602D01* +X124983501Y-95480264D01* +X124983489Y-95480261D01* +X124828845Y-95449500D01* +X124828842Y-95449500D01* +X124674500Y-95449500D01* +X124607461Y-95429815D01* +X124561706Y-95377011D01* +X124550500Y-95325500D01* +X124550500Y-95171155D01* +X124550499Y-95171153D01* +X124529684Y-95066510D01* +X124519737Y-95016503D01* +X124515286Y-95005757D01* +X124459397Y-94870827D01* +X124459390Y-94870814D01* +X124371789Y-94739711D01* +X124371786Y-94739707D01* +X124260292Y-94628213D01* +X124260288Y-94628210D01* +X124129185Y-94540609D01* +X124129172Y-94540602D01* +X123983501Y-94480264D01* +X123983489Y-94480261D01* +X123828845Y-94449500D01* +X123828842Y-94449500D01* +X123671158Y-94449500D01* +X123671155Y-94449500D01* +X123516510Y-94480261D01* +X123516498Y-94480264D01* +X123370827Y-94540602D01* +X123370814Y-94540609D01* +X123239711Y-94628210D01* +X123239707Y-94628213D01* +X123128213Y-94739707D01* +X123128210Y-94739711D01* +X123040609Y-94870814D01* +X123040602Y-94870827D01* +X122980264Y-95016498D01* +X122980261Y-95016510D01* +X122949500Y-95171153D01* +X120250500Y-95171153D01* +X120250500Y-93271153D01* +X128899500Y-93271153D01* +X128899500Y-93428846D01* +X128930261Y-93583489D01* +X128930264Y-93583501D01* +X128990602Y-93729172D01* +X128990609Y-93729185D01* +X129078210Y-93860288D01* +X129078213Y-93860292D01* +X129189707Y-93971786D01* +X129189711Y-93971789D01* +X129320814Y-94059390D01* +X129320827Y-94059397D01* +X129466498Y-94119735D01* +X129466503Y-94119737D01* +X129621153Y-94150499D01* +X129621156Y-94150500D01* +X129621158Y-94150500D01* +X129778844Y-94150500D01* +X129778845Y-94150499D01* +X129933497Y-94119737D01* +X130079179Y-94059394D01* +X130210289Y-93971789D01* +X130321789Y-93860289D01* +X130409394Y-93729179D01* +X130469737Y-93583497D01* +X130500500Y-93428842D01* +X130500500Y-93341804D01* +X130520185Y-93274765D01* +X130555606Y-93238704D01* +X130580923Y-93221789D01* +X130692423Y-93110289D01* +X130780028Y-92979179D01* +X130783488Y-92970827D01* +X130837797Y-92839711D01* +X130840371Y-92833497D01* +X130871134Y-92678842D01* +X130871134Y-92521158D01* +X130871134Y-92521155D01* +X130871133Y-92521153D01* +X130840372Y-92366510D01* +X130840371Y-92366503D01* +X130840369Y-92366498D01* +X130780031Y-92220827D01* +X130780024Y-92220814D01* +X130692423Y-92089711D01* +X130692420Y-92089707D01* +X130580926Y-91978213D01* +X130580922Y-91978210D01* +X130449819Y-91890609D01* +X130449806Y-91890602D01* +X130304135Y-91830264D01* +X130304123Y-91830261D01* +X130149479Y-91799500D01* +X130149476Y-91799500D01* +X129991792Y-91799500D01* +X129991789Y-91799500D01* +X129837144Y-91830261D01* +X129837132Y-91830264D01* +X129691461Y-91890602D01* +X129691448Y-91890609D01* +X129560345Y-91978210D01* +X129560341Y-91978213D01* +X129448847Y-92089707D01* +X129448844Y-92089711D01* +X129361243Y-92220814D01* +X129361236Y-92220827D01* +X129300898Y-92366498D01* +X129300895Y-92366510D01* +X129270134Y-92521153D01* +X129270134Y-92608194D01* +X129250449Y-92675233D01* +X129215026Y-92711296D01* +X129189707Y-92728213D01* +X129078213Y-92839707D01* +X129078210Y-92839711D01* +X128990609Y-92970814D01* +X128990602Y-92970827D01* +X128930264Y-93116498D01* +X128930261Y-93116510D01* +X128899500Y-93271153D01* +X120250500Y-93271153D01* +X120250500Y-90621153D01* +X140149500Y-90621153D01* +X140149500Y-90778846D01* +X140180261Y-90933489D01* +X140180264Y-90933501D01* +X140240602Y-91079172D01* +X140240609Y-91079185D01* +X140328210Y-91210288D01* +X140328213Y-91210292D01* +X140439707Y-91321786D01* +X140439711Y-91321789D01* +X140570814Y-91409390D01* +X140570827Y-91409397D01* +X140670060Y-91450500D01* +X140716503Y-91469737D01* +X140871153Y-91500499D01* +X140871156Y-91500500D01* +X140871158Y-91500500D01* +X141028844Y-91500500D01* +X141028845Y-91500499D01* +X141183497Y-91469737D01* +X141329179Y-91409394D01* +X141460289Y-91321789D01* +X141571789Y-91210289D01* +X141659394Y-91079179D01* +X141719737Y-90933497D01* +X141750500Y-90778842D01* +X141750500Y-90621158D01* +X141750500Y-90621155D01* +X141744155Y-90589258D01* +X141744155Y-90589257D01* +X141740554Y-90571153D01* +X143999500Y-90571153D01* +X143999500Y-90728846D01* +X144030261Y-90883489D01* +X144030264Y-90883501D01* +X144090602Y-91029172D01* +X144090609Y-91029185D01* +X144178210Y-91160288D01* +X144178213Y-91160292D01* +X144289707Y-91271786D01* +X144289711Y-91271789D01* +X144420814Y-91359390D01* +X144420827Y-91359397D01* +X144566498Y-91419735D01* +X144566503Y-91419737D01* +X144721153Y-91450499D01* +X144721156Y-91450500D01* +X144721158Y-91450500D01* +X144878844Y-91450500D01* +X144878845Y-91450499D01* +X145033497Y-91419737D01* +X145179179Y-91359394D01* +X145310289Y-91271789D01* +X145421789Y-91160289D01* +X145509394Y-91029179D01* +X145569737Y-90883497D01* +X145600500Y-90728842D01* +X145600500Y-90571158D01* +X145600500Y-90571155D01* +X145600499Y-90571153D01* +X145579684Y-90466510D01* +X145569737Y-90416503D01* +X145530102Y-90320814D01* +X145509397Y-90270827D01* +X145509390Y-90270814D01* +X145421789Y-90139711D01* +X145421786Y-90139707D01* +X145310292Y-90028213D01* +X145310288Y-90028210D01* +X145179185Y-89940609D01* +X145179172Y-89940602D01* +X145033501Y-89880264D01* +X145033489Y-89880261D01* +X144878845Y-89849500D01* +X144878842Y-89849500D01* +X144721158Y-89849500D01* +X144721155Y-89849500D01* +X144566510Y-89880261D01* +X144566498Y-89880264D01* +X144420827Y-89940602D01* +X144420814Y-89940609D01* +X144289711Y-90028210D01* +X144289707Y-90028213D01* +X144178213Y-90139707D01* +X144178210Y-90139711D01* +X144090609Y-90270814D01* +X144090602Y-90270827D01* +X144030264Y-90416498D01* +X144030261Y-90416510D01* +X143999500Y-90571153D01* +X141740554Y-90571153D01* +X141719738Y-90466510D01* +X141719737Y-90466503D01* +X141719735Y-90466498D01* +X141659397Y-90320827D01* +X141659390Y-90320814D01* +X141571789Y-90189711D01* +X141571786Y-90189707D01* +X141460292Y-90078213D01* +X141460288Y-90078210D01* +X141329185Y-89990609D01* +X141329172Y-89990602D01* +X141183501Y-89930264D01* +X141183489Y-89930261D01* +X141028845Y-89899500D01* +X141028842Y-89899500D01* +X140871158Y-89899500D01* +X140871155Y-89899500D01* +X140716510Y-89930261D01* +X140716498Y-89930264D01* +X140570827Y-89990602D01* +X140570814Y-89990609D01* +X140439711Y-90078210D01* +X140439707Y-90078213D01* +X140328213Y-90189707D01* +X140328210Y-90189711D01* +X140240609Y-90320814D01* +X140240602Y-90320827D01* +X140180264Y-90466498D01* +X140180261Y-90466510D01* +X140149500Y-90621153D01* +X120250500Y-90621153D01* +X120250500Y-88622070D01* +X130124500Y-88622070D01* +X130124500Y-88877929D01* +X130164526Y-89130640D01* +X130243588Y-89373972D01* +X130243589Y-89373975D01* +X130359750Y-89601950D01* +X130510132Y-89808935D01* +X130510136Y-89808940D01* +X130691059Y-89989863D01* +X130691064Y-89989867D01* +X130812663Y-90078213D01* +X130898053Y-90140252D01* +X131047080Y-90216185D01* +X131126024Y-90256410D01* +X131126027Y-90256411D01* +X131170396Y-90270827D01* +X131369361Y-90335474D01* +X131622070Y-90375500D01* +X131622071Y-90375500D01* +X131877929Y-90375500D01* +X131877930Y-90375500D01* +X132130639Y-90335474D01* +X132373975Y-90256410D01* +X132601947Y-90140252D01* +X132808942Y-89989862D01* +X132989862Y-89808942D01* +X133140252Y-89601947D01* +X133256410Y-89373975D01* +X133335474Y-89130639D01* +X133375500Y-88877930D01* +X133375500Y-88622070D01* +X136624500Y-88622070D01* +X136624500Y-88877929D01* +X136664526Y-89130640D01* +X136743588Y-89373972D01* +X136743589Y-89373975D01* +X136859750Y-89601950D01* +X137010132Y-89808935D01* +X137010136Y-89808940D01* +X137191059Y-89989863D01* +X137191064Y-89989867D01* +X137312663Y-90078213D01* +X137398053Y-90140252D01* +X137547080Y-90216185D01* +X137626024Y-90256410D01* +X137626027Y-90256411D01* +X137670396Y-90270827D01* +X137869361Y-90335474D01* +X138122070Y-90375500D01* +X138122071Y-90375500D01* +X138377929Y-90375500D01* +X138377930Y-90375500D01* +X138630639Y-90335474D01* +X138873975Y-90256410D01* +X139101947Y-90140252D01* +X139308942Y-89989862D01* +X139489862Y-89808942D01* +X139640252Y-89601947D01* +X139756410Y-89373975D01* +X139835474Y-89130639D01* +X139875500Y-88877930D01* +X139875500Y-88622070D01* +X139835474Y-88369361D01* +X139773681Y-88179179D01* +X139756411Y-88126027D01* +X139756405Y-88126014D01* +X139728559Y-88071363D01* +X139728557Y-88071361D01* +X139702977Y-88021158D01* +X139702974Y-88021153D01* +X144599500Y-88021153D01* +X144599500Y-88178846D01* +X144630261Y-88333489D01* +X144630264Y-88333501D01* +X144690602Y-88479172D01* +X144690609Y-88479185D01* +X144778210Y-88610288D01* +X144778213Y-88610292D01* +X144889707Y-88721786D01* +X144889711Y-88721789D01* +X145020814Y-88809390D01* +X145020827Y-88809397D01* +X145166498Y-88869735D01* +X145166503Y-88869737D01* +X145321153Y-88900499D01* +X145321156Y-88900500D01* +X145321158Y-88900500D01* +X145478844Y-88900500D01* +X145478845Y-88900499D01* +X145633497Y-88869737D01* +X145779179Y-88809394D01* +X145910289Y-88721789D01* +X146021789Y-88610289D01* +X146109394Y-88479179D01* +X146169737Y-88333497D01* +X146200500Y-88178842D01* +X146200500Y-88021158D01* +X146200500Y-88021155D01* +X146200499Y-88021153D01* +X146169737Y-87866503D01* +X146109534Y-87721158D01* +X146109397Y-87720827D01* +X146109390Y-87720814D01* +X146021789Y-87589711D01* +X146021786Y-87589707D01* +X145910292Y-87478213D01* +X145910288Y-87478210D01* +X145779185Y-87390609D01* +X145779172Y-87390602D01* +X145633501Y-87330264D01* +X145633489Y-87330261D01* +X145478845Y-87299500D01* +X145478842Y-87299500D01* +X145321158Y-87299500D01* +X145321155Y-87299500D01* +X145166510Y-87330261D01* +X145166498Y-87330264D01* +X145020827Y-87390602D01* +X145020814Y-87390609D01* +X144889711Y-87478210D01* +X144889707Y-87478213D01* +X144778213Y-87589707D01* +X144778210Y-87589711D01* +X144690609Y-87720814D01* +X144690602Y-87720827D01* +X144630264Y-87866498D01* +X144630261Y-87866510D01* +X144599500Y-88021153D01* +X139702974Y-88021153D01* +X139640252Y-87898053D01* +X139511729Y-87721155D01* +X139489867Y-87691064D01* +X139489863Y-87691059D01* +X139308940Y-87510136D01* +X139308935Y-87510132D01* +X139101950Y-87359750D01* +X139101949Y-87359749D01* +X139101947Y-87359748D01* +X139028910Y-87322533D01* +X138873975Y-87243589D01* +X138873972Y-87243588D01* +X138630640Y-87164526D01* +X138504284Y-87144513D01* +X138377930Y-87124500D01* +X138122070Y-87124500D01* +X138037833Y-87137842D01* +X137869359Y-87164526D01* +X137626027Y-87243588D01* +X137626024Y-87243589D01* +X137398049Y-87359750D01* +X137191064Y-87510132D01* +X137191059Y-87510136D01* +X137010136Y-87691059D01* +X137010132Y-87691064D01* +X136859750Y-87898049D01* +X136743589Y-88126024D01* +X136743588Y-88126027D01* +X136664526Y-88369359D01* +X136624500Y-88622070D01* +X133375500Y-88622070D01* +X133335474Y-88369361D01* +X133273681Y-88179179D01* +X133256411Y-88126027D01* +X133256410Y-88126024D01* +X133202975Y-88021153D01* +X133140252Y-87898053D01* +X133011729Y-87721155D01* +X132989867Y-87691064D01* +X132989863Y-87691059D01* +X132808940Y-87510136D01* +X132808935Y-87510132D01* +X132601950Y-87359750D01* +X132601949Y-87359749D01* +X132601947Y-87359748D01* +X132528910Y-87322533D01* +X132373975Y-87243589D01* +X132373972Y-87243588D01* +X132130640Y-87164526D01* +X132004284Y-87144513D01* +X131877930Y-87124500D01* +X131622070Y-87124500D01* +X131537833Y-87137842D01* +X131369359Y-87164526D01* +X131126027Y-87243588D01* +X131126024Y-87243589D01* +X130898049Y-87359750D01* +X130691064Y-87510132D01* +X130691059Y-87510136D01* +X130510136Y-87691059D01* +X130510132Y-87691064D01* +X130359750Y-87898049D01* +X130243589Y-88126024D01* +X130243588Y-88126027D01* +X130164526Y-88369359D01* +X130124500Y-88622070D01* +X120250500Y-88622070D01* +X120250500Y-87721153D01* +X121499500Y-87721153D01* +X121499500Y-87878846D01* +X121530261Y-88033489D01* +X121530264Y-88033501D01* +X121590602Y-88179172D01* +X121590609Y-88179185D01* +X121678210Y-88310288D01* +X121678213Y-88310292D01* +X121789707Y-88421786D01* +X121789711Y-88421789D01* +X121920814Y-88509390D01* +X121920827Y-88509397D01* +X122066498Y-88569735D01* +X122066503Y-88569737D01* +X122221153Y-88600499D01* +X122221156Y-88600500D01* +X122221158Y-88600500D01* +X122378844Y-88600500D01* +X122378845Y-88600499D01* +X122533497Y-88569737D01* +X122679179Y-88509394D01* +X122810289Y-88421789D01* +X122921789Y-88310289D01* +X123009394Y-88179179D01* +X123069737Y-88033497D01* +X123100500Y-87878842D01* +X123100500Y-87721158D01* +X123100500Y-87721155D01* +X123100499Y-87721153D01* +X123074353Y-87589711D01* +X123069737Y-87566503D01* +X123046388Y-87510132D01* +X123009397Y-87420827D01* +X123009390Y-87420814D01* +X122921789Y-87289711D01* +X122921786Y-87289707D01* +X122810292Y-87178213D01* +X122810288Y-87178210D01* +X122679185Y-87090609D01* +X122679172Y-87090602D01* +X122533501Y-87030264D01* +X122533489Y-87030261D01* +X122378845Y-86999500D01* +X122378842Y-86999500D01* +X122221158Y-86999500D01* +X122221155Y-86999500D01* +X122066510Y-87030261D01* +X122066498Y-87030264D01* +X121920827Y-87090602D01* +X121920814Y-87090609D01* +X121789711Y-87178210D01* +X121789707Y-87178213D01* +X121678213Y-87289707D01* +X121678210Y-87289711D01* +X121590609Y-87420814D01* +X121590602Y-87420827D01* +X121530264Y-87566498D01* +X121530261Y-87566510D01* +X121499500Y-87721153D01* +X120250500Y-87721153D01* +X120250500Y-85693995D01* +X121099499Y-85693995D01* +X121126418Y-85829322D01* +X121126421Y-85829332D01* +X121179221Y-85956804D01* +X121179228Y-85956817D01* +X121255885Y-86071541D01* +X121255888Y-86071545D01* +X121353454Y-86169111D01* +X121353458Y-86169114D01* +X121468182Y-86245771D01* +X121468195Y-86245778D01* +X121595667Y-86298578D01* +X121595672Y-86298580D01* +X121595676Y-86298580D01* +X121595677Y-86298581D01* +X121731004Y-86325500D01* +X121731007Y-86325500D01* +X121868995Y-86325500D01* +X121960041Y-86307389D01* +X122004328Y-86298580D01* +X122131811Y-86245775D01* +X122168660Y-86221153D01* +X143799500Y-86221153D01* +X143799500Y-86378846D01* +X143830261Y-86533489D01* +X143830264Y-86533501D01* +X143890602Y-86679172D01* +X143890609Y-86679185D01* +X143978210Y-86810288D01* +X143978213Y-86810292D01* +X144089707Y-86921786D01* +X144089711Y-86921789D01* +X144220814Y-87009390D01* +X144220827Y-87009397D01* +X144366498Y-87069735D01* +X144366503Y-87069737D01* +X144521153Y-87100499D01* +X144521156Y-87100500D01* +X144521158Y-87100500D01* +X144678844Y-87100500D01* +X144678845Y-87100499D01* +X144833497Y-87069737D01* +X144979179Y-87009394D01* +X145110289Y-86921789D01* +X145221789Y-86810289D01* +X145309394Y-86679179D01* +X145369737Y-86533497D01* +X145400500Y-86378842D01* +X145400500Y-86221158D01* +X145400500Y-86221155D01* +X145400499Y-86221153D01* +X145369738Y-86066510D01* +X145369737Y-86066503D01* +X145324304Y-85956817D01* +X145309397Y-85920827D01* +X145309390Y-85920814D01* +X145221789Y-85789711D01* +X145221786Y-85789707D01* +X145126074Y-85693995D01* +X147499499Y-85693995D01* +X147526418Y-85829322D01* +X147526421Y-85829332D01* +X147579221Y-85956804D01* +X147579228Y-85956817D01* +X147655885Y-86071541D01* +X147655888Y-86071545D01* +X147753454Y-86169111D01* +X147753458Y-86169114D01* +X147868182Y-86245771D01* +X147868195Y-86245778D01* +X147995667Y-86298578D01* +X147995672Y-86298580D01* +X147995676Y-86298580D01* +X147995677Y-86298581D01* +X148131004Y-86325500D01* +X148131007Y-86325500D01* +X148268995Y-86325500D01* +X148360041Y-86307389D01* +X148404328Y-86298580D01* +X148531811Y-86245775D01* +X148646542Y-86169114D01* +X148744114Y-86071542D01* +X148820775Y-85956811D01* +X148873580Y-85829328D01* +X148888084Y-85756411D01* +X148900500Y-85693995D01* +X148900500Y-85556004D01* +X148873581Y-85420677D01* +X148873580Y-85420676D01* +X148873580Y-85420672D01* +X148873578Y-85420667D01* +X148820778Y-85293195D01* +X148820771Y-85293182D01* +X148744114Y-85178458D01* +X148744111Y-85178454D01* +X148646545Y-85080888D01* +X148646541Y-85080885D01* +X148531817Y-85004228D01* +X148531804Y-85004221D01* +X148404332Y-84951421D01* +X148404322Y-84951418D01* +X148268995Y-84924500D01* +X148268993Y-84924500D01* +X148131007Y-84924500D01* +X148131005Y-84924500D01* +X147995677Y-84951418D01* +X147995667Y-84951421D01* +X147868195Y-85004221D01* +X147868182Y-85004228D01* +X147753458Y-85080885D01* +X147753454Y-85080888D01* +X147655888Y-85178454D01* +X147655885Y-85178458D01* +X147579228Y-85293182D01* +X147579221Y-85293195D01* +X147526421Y-85420667D01* +X147526418Y-85420677D01* +X147499500Y-85556004D01* +X147499500Y-85556007D01* +X147499500Y-85693993D01* +X147499500Y-85693995D01* +X147499499Y-85693995D01* +X145126074Y-85693995D01* +X145110292Y-85678213D01* +X145110288Y-85678210D01* +X145072584Y-85653017D01* +X144979185Y-85590609D01* +X144979172Y-85590602D01* +X144833501Y-85530264D01* +X144833489Y-85530261D01* +X144678845Y-85499500D01* +X144678842Y-85499500D01* +X144521158Y-85499500D01* +X144521155Y-85499500D01* +X144366510Y-85530261D01* +X144366498Y-85530264D01* +X144220827Y-85590602D01* +X144220814Y-85590609D01* +X144089711Y-85678210D01* +X144089707Y-85678213D01* +X143978213Y-85789707D01* +X143978210Y-85789711D01* +X143890609Y-85920814D01* +X143890602Y-85920827D01* +X143830264Y-86066498D01* +X143830261Y-86066510D01* +X143799500Y-86221153D01* +X122168660Y-86221153D01* +X122246542Y-86169114D01* +X122246545Y-86169111D01* +X122288272Y-86127385D01* +X122344111Y-86071545D01* +X122344114Y-86071542D01* +X122420775Y-85956811D01* +X122473580Y-85829328D01* +X122488084Y-85756411D01* +X122500500Y-85693995D01* +X122500500Y-85556004D01* +X122473581Y-85420677D01* +X122473580Y-85420676D01* +X122473580Y-85420672D01* +X122473578Y-85420667D01* +X122420778Y-85293195D01* +X122420771Y-85293182D01* +X122344114Y-85178458D01* +X122344111Y-85178454D01* +X122246545Y-85080888D01* +X122246541Y-85080885D01* +X122131817Y-85004228D01* +X122131804Y-85004221D01* +X122004332Y-84951421D01* +X122004322Y-84951418D01* +X121868995Y-84924500D01* +X121868993Y-84924500D01* +X121731007Y-84924500D01* +X121731005Y-84924500D01* +X121595677Y-84951418D01* +X121595667Y-84951421D01* +X121468195Y-85004221D01* +X121468182Y-85004228D01* +X121353458Y-85080885D01* +X121353454Y-85080888D01* +X121255888Y-85178454D01* +X121255885Y-85178458D01* +X121179228Y-85293182D01* +X121179221Y-85293195D01* +X121126421Y-85420667D01* +X121126418Y-85420677D01* +X121099500Y-85556004D01* +X121099500Y-85556007D01* +X121099500Y-85693993D01* +X121099500Y-85693995D01* +X121099499Y-85693995D01* +X120250500Y-85693995D01* +X120250500Y-83621153D01* +X123299500Y-83621153D01* +X123299500Y-83778846D01* +X123330261Y-83933489D01* +X123330264Y-83933501D01* +X123390602Y-84079172D01* +X123390609Y-84079185D01* +X123478210Y-84210288D01* +X123478213Y-84210292D01* +X123589707Y-84321786D01* +X123589711Y-84321789D01* +X123720814Y-84409390D01* +X123720827Y-84409397D01* +X123866498Y-84469735D01* +X123866503Y-84469737D01* +X124021153Y-84500499D01* +X124021156Y-84500500D01* +X124021158Y-84500500D01* +X124178844Y-84500500D01* +X124178845Y-84500499D01* +X124333497Y-84469737D01* +X124479179Y-84409394D01* +X124610289Y-84321789D01* +X124721789Y-84210289D01* +X124809394Y-84079179D01* +X124812393Y-84071940D01* +X124869735Y-83933501D01* +X124869737Y-83933497D01* +X124900500Y-83778842D01* +X124900500Y-83621158D01* +X124900500Y-83621155D01* +X124900499Y-83621153D01* +X124899547Y-83616365D01* +X124869737Y-83466503D01* +X124835411Y-83383634D01* +X126899500Y-83383634D01* +X126899500Y-83616365D01* +X126899501Y-83616382D01* +X126925029Y-83810291D01* +X126929879Y-83847126D01* +X126989527Y-84069736D01* +X126990120Y-84071947D01* +X127079180Y-84286960D01* +X127079188Y-84286976D01* +X127195553Y-84488524D01* +X127195564Y-84488540D01* +X127337242Y-84673179D01* +X127337248Y-84673186D01* +X127501813Y-84837751D01* +X127501820Y-84837757D01* +X127614866Y-84924500D01* +X127686468Y-84979442D01* +X127686475Y-84979446D01* +X127888023Y-85095811D01* +X127888039Y-85095819D01* +X128103052Y-85184879D01* +X128103054Y-85184879D01* +X128103060Y-85184882D01* +X128327874Y-85245121D01* +X128558628Y-85275500D01* +X128558635Y-85275500D01* +X128791365Y-85275500D01* +X128791372Y-85275500D01* +X129022126Y-85245121D01* +X129246940Y-85184882D01* +X129447165Y-85101947D01* +X129461960Y-85095819D01* +X129461963Y-85095817D01* +X129461969Y-85095815D01* +X129663532Y-84979442D01* +X129848181Y-84837756D01* +X129994657Y-84691279D01* +X130055978Y-84657796D01* +X130125670Y-84662780D01* +X130181604Y-84704651D01* +X130200268Y-84740644D01* +X130243588Y-84873972D01* +X130243589Y-84873975D01* +X130297328Y-84979442D01* +X130349016Y-85080885D01* +X130359750Y-85101950D01* +X130510132Y-85308935D01* +X130510136Y-85308940D01* +X130691059Y-85489863D01* +X130691064Y-85489867D01* +X130782095Y-85556004D01* +X130898053Y-85640252D01* +X131047080Y-85716185D01* +X131126024Y-85756410D01* +X131126027Y-85756411D01* +X131228503Y-85789707D01* +X131369361Y-85835474D01* +X131622070Y-85875500D01* +X131622071Y-85875500D01* +X131877929Y-85875500D01* +X131877930Y-85875500D01* +X132130639Y-85835474D01* +X132373975Y-85756410D01* +X132601947Y-85640252D01* +X132808942Y-85489862D01* +X132989862Y-85308942D01* +X133140252Y-85101947D01* +X133256410Y-84873975D01* +X133335474Y-84630639D01* +X133375500Y-84377930D01* +X133375500Y-84122070D01* +X136624500Y-84122070D01* +X136624500Y-84377929D01* +X136664526Y-84630640D01* +X136743588Y-84873972D01* +X136743589Y-84873975D01* +X136797328Y-84979442D01* +X136849016Y-85080885D01* +X136859750Y-85101950D01* +X137010132Y-85308935D01* +X137010136Y-85308940D01* +X137191059Y-85489863D01* +X137191064Y-85489867D01* +X137282095Y-85556004D01* +X137398053Y-85640252D01* +X137547080Y-85716185D01* +X137626024Y-85756410D01* +X137626027Y-85756411D01* +X137728503Y-85789707D01* +X137869361Y-85835474D01* +X138122070Y-85875500D01* +X138122071Y-85875500D01* +X138377929Y-85875500D01* +X138377930Y-85875500D01* +X138630639Y-85835474D01* +X138873975Y-85756410D01* +X139101947Y-85640252D01* +X139308942Y-85489862D01* +X139489862Y-85308942D01* +X139640252Y-85101947D01* +X139756410Y-84873975D01* +X139799731Y-84740644D01* +X139839168Y-84682969D01* +X139903526Y-84655770D01* +X139972373Y-84667684D01* +X140005343Y-84691281D01* +X140151813Y-84837751D01* +X140151820Y-84837757D01* +X140264866Y-84924500D01* +X140336468Y-84979442D01* +X140336475Y-84979446D01* +X140538023Y-85095811D01* +X140538039Y-85095819D01* +X140753052Y-85184879D01* +X140753054Y-85184879D01* +X140753060Y-85184882D01* +X140977874Y-85245121D01* +X141208628Y-85275500D01* +X141208635Y-85275500D01* +X141441365Y-85275500D01* +X141441372Y-85275500D01* +X141672126Y-85245121D01* +X141896940Y-85184882D01* +X142097165Y-85101947D01* +X142111960Y-85095819D01* +X142111963Y-85095817D01* +X142111969Y-85095815D01* +X142313532Y-84979442D01* +X142498181Y-84837756D01* +X142662756Y-84673181D01* +X142804442Y-84488532D01* +X142920815Y-84286969D01* +X143009882Y-84071940D01* +X143070121Y-83847126D01* +X143100500Y-83616372D01* +X143100500Y-83383628D01* +X143079110Y-83221152D01* +X145448028Y-83221152D01* +X145448028Y-83378845D01* +X145478789Y-83533488D01* +X145478792Y-83533500D01* +X145539130Y-83679171D01* +X145539137Y-83679184D01* +X145626738Y-83810287D01* +X145626741Y-83810291D01* +X145738235Y-83921785D01* +X145738239Y-83921788D01* +X145869342Y-84009389D01* +X145869355Y-84009396D01* +X146015026Y-84069734D01* +X146015031Y-84069736D01* +X146169681Y-84100498D01* +X146169684Y-84100499D01* +X146169686Y-84100499D01* +X146327372Y-84100499D01* +X146327373Y-84100498D01* +X146482025Y-84069736D01* +X146627707Y-84009393D01* +X146758817Y-83921788D01* +X146870317Y-83810288D01* +X146957922Y-83679178D01* +X147018265Y-83533496D01* +X147049028Y-83378841D01* +X147049028Y-83221157D01* +X147049028Y-83221154D01* +X147049027Y-83221152D01* +X147035446Y-83152877D01* +X147018265Y-83066502D01* +X147009991Y-83046527D01* +X146957925Y-82920826D01* +X146957918Y-82920813D01* +X146870317Y-82789710D01* +X146870314Y-82789706D01* +X146758820Y-82678212D01* +X146758816Y-82678209D01* +X146627713Y-82590608D01* +X146627700Y-82590601D01* +X146482029Y-82530263D01* +X146482017Y-82530260D01* +X146327373Y-82499499D01* +X146327370Y-82499499D01* +X146169686Y-82499499D01* +X146169683Y-82499499D01* +X146015038Y-82530260D01* +X146015026Y-82530263D01* +X145869355Y-82590601D01* +X145869342Y-82590608D01* +X145738239Y-82678209D01* +X145738235Y-82678212D01* +X145626741Y-82789706D01* +X145626738Y-82789710D01* +X145539137Y-82920813D01* +X145539130Y-82920826D01* +X145478792Y-83066497D01* +X145478789Y-83066509D01* +X145448028Y-83221152D01* +X143079110Y-83221152D01* +X143070121Y-83152874D01* +X143009882Y-82928060D01* +X143009879Y-82928052D01* +X142920819Y-82713039D01* +X142920811Y-82713023D01* +X142804446Y-82511475D01* +X142804442Y-82511468D01* +X142796662Y-82501329D01* +X142771467Y-82436162D01* +X142785504Y-82367717D01* +X142834317Y-82317726D01* +X142902408Y-82302061D01* +X142951332Y-82315357D01* +X143144406Y-82413734D01* +X143144408Y-82413734D01* +X143144411Y-82413736D01* +X143372778Y-82487937D01* +X143609941Y-82525500D01* +X143609942Y-82525500D01* +X143850058Y-82525500D01* +X143850059Y-82525500D01* +X144087222Y-82487937D01* +X144315589Y-82413736D01* +X144529536Y-82304724D01* +X144723796Y-82163586D01* +X144893586Y-81993796D01* +X145034724Y-81799536D01* +X145143736Y-81585589D01* +X145189743Y-81443995D01* +X147499499Y-81443995D01* +X147526418Y-81579322D01* +X147526421Y-81579332D01* +X147579221Y-81706804D01* +X147579228Y-81706817D01* +X147655885Y-81821541D01* +X147655888Y-81821545D01* +X147753454Y-81919111D01* +X147753458Y-81919114D01* +X147868182Y-81995771D01* +X147868195Y-81995778D01* +X147995667Y-82048578D01* +X147995672Y-82048580D01* +X147995676Y-82048580D01* +X147995677Y-82048581D01* +X148131004Y-82075500D01* +X148131007Y-82075500D01* +X148268995Y-82075500D01* +X148360041Y-82057389D01* +X148404328Y-82048580D01* +X148531811Y-81995775D01* +X148646542Y-81919114D01* +X148744114Y-81821542D01* +X148820775Y-81706811D01* +X148873580Y-81579328D01* +X148900500Y-81443993D01* +X148900500Y-81306007D01* +X148900500Y-81306004D01* +X148873581Y-81170677D01* +X148873580Y-81170676D01* +X148873580Y-81170672D01* +X148873578Y-81170667D01* +X148820778Y-81043195D01* +X148820771Y-81043182D01* +X148744114Y-80928458D01* +X148744111Y-80928454D01* +X148646545Y-80830888D01* +X148646541Y-80830885D01* +X148531817Y-80754228D01* +X148531804Y-80754221D01* +X148404332Y-80701421D01* +X148404322Y-80701418D01* +X148268995Y-80674500D01* +X148268993Y-80674500D01* +X148131007Y-80674500D01* +X148131005Y-80674500D01* +X147995677Y-80701418D01* +X147995667Y-80701421D01* +X147868195Y-80754221D01* +X147868182Y-80754228D01* +X147753458Y-80830885D01* +X147753454Y-80830888D01* +X147655888Y-80928454D01* +X147655885Y-80928458D01* +X147579228Y-81043182D01* +X147579221Y-81043195D01* +X147526421Y-81170667D01* +X147526418Y-81170677D01* +X147499500Y-81306004D01* +X147499500Y-81306007D01* +X147499500Y-81443993D01* +X147499500Y-81443995D01* +X147499499Y-81443995D01* +X145189743Y-81443995D01* +X145217937Y-81357222D01* +X145255500Y-81120059D01* +X145255500Y-80879941D01* +X145217937Y-80642778D01* +X145143736Y-80414411D01* +X145143734Y-80414408D01* +X145143734Y-80414406D01* +X145034723Y-80200463D01* +X144893586Y-80006204D01* +X144725063Y-79837681D01* +X144691578Y-79776358D01* +X144696562Y-79706666D01* +X144725063Y-79662319D01* +X144893586Y-79493796D01* +X145034724Y-79299536D01* +X145143736Y-79085589D01* +X145217937Y-78857222D01* +X145255500Y-78620059D01* +X145255500Y-78379941D01* +X145217937Y-78142778D01* +X145143736Y-77914411D01* +X145143734Y-77914408D01* +X145143734Y-77914406D01* +X145034723Y-77700463D01* +X144893586Y-77506204D01* +X144723796Y-77336414D01* +X144671824Y-77298654D01* +X144657859Y-77280544D01* +X144657426Y-77280978D01* +X143879822Y-76503375D01* +X143932642Y-76489222D01* +X144052357Y-76420104D01* +X144150104Y-76322357D01* +X144219222Y-76202642D01* +X144233375Y-76149822D01* +X144970556Y-76887004D01* +X144970556Y-76887003D01* +X145034296Y-76799274D01* +X145143271Y-76585401D01* +X145217450Y-76357105D01* +X145255000Y-76120025D01* +X145255000Y-75879974D01* +X145225543Y-75693995D01* +X147499499Y-75693995D01* +X147526418Y-75829322D01* +X147526421Y-75829332D01* +X147579221Y-75956804D01* +X147579228Y-75956817D01* +X147655885Y-76071541D01* +X147655888Y-76071545D01* +X147753454Y-76169111D01* +X147753458Y-76169114D01* +X147868182Y-76245771D01* +X147868195Y-76245778D01* +X147995667Y-76298578D01* +X147995672Y-76298580D01* +X147995676Y-76298580D01* +X147995677Y-76298581D01* +X148131004Y-76325500D01* +X148131007Y-76325500D01* +X148268995Y-76325500D01* +X148360041Y-76307389D01* +X148404328Y-76298580D01* +X148531811Y-76245775D01* +X148646542Y-76169114D01* +X148744114Y-76071542D01* +X148820775Y-75956811D01* +X148873580Y-75829328D01* +X148882389Y-75785041D01* +X148900500Y-75693995D01* +X148900500Y-75556004D01* +X148873581Y-75420677D01* +X148873580Y-75420676D01* +X148873580Y-75420672D01* +X148871064Y-75414598D01* +X148820778Y-75293195D01* +X148820771Y-75293182D01* +X148744114Y-75178458D01* +X148744111Y-75178454D01* +X148646545Y-75080888D01* +X148646541Y-75080885D01* +X148531817Y-75004228D01* +X148531804Y-75004221D01* +X148404332Y-74951421D01* +X148404322Y-74951418D01* +X148268995Y-74924500D01* +X148268993Y-74924500D01* +X148131007Y-74924500D01* +X148131005Y-74924500D01* +X147995677Y-74951418D01* +X147995667Y-74951421D01* +X147868195Y-75004221D01* +X147868182Y-75004228D01* +X147753458Y-75080885D01* +X147753454Y-75080888D01* +X147655888Y-75178454D01* +X147655885Y-75178458D01* +X147579228Y-75293182D01* +X147579221Y-75293195D01* +X147526421Y-75420667D01* +X147526418Y-75420677D01* +X147499500Y-75556004D01* +X147499500Y-75556007D01* +X147499500Y-75693993D01* +X147499500Y-75693995D01* +X147499499Y-75693995D01* +X145225543Y-75693995D01* +X145217449Y-75642893D01* +X145217449Y-75642890D01* +X145199690Y-75588233D01* +X145143271Y-75414598D01* +X145034294Y-75200722D01* +X144970557Y-75112995D01* +X144970556Y-75112994D01* +X144233374Y-75850176D01* +X144219222Y-75797358D01* +X144150104Y-75677643D01* +X144052357Y-75579896D01* +X143932642Y-75510778D01* +X143879821Y-75496624D01* +X144617003Y-74759443D01* +X144617003Y-74759441D01* +X144529277Y-74695705D01* +X144315401Y-74586728D01* +X144087105Y-74512549D01* +X143850025Y-74475000D01* +X143609975Y-74475000D01* +X143372894Y-74512549D01* +X143144598Y-74586728D01* +X142950626Y-74685563D01* +X142881957Y-74698459D01* +X142817216Y-74672183D01* +X142776959Y-74615076D01* +X142773967Y-74545271D01* +X142795955Y-74499591D01* +X142804442Y-74488532D01* +X142920815Y-74286969D01* +X142977802Y-74149390D01* +X143009879Y-74071947D01* +X143009878Y-74071947D01* +X143009882Y-74071940D01* +X143070121Y-73847126D01* +X143100500Y-73616372D01* +X143100500Y-73383628D01* +X143070121Y-73152874D01* +X143014212Y-72944220D01* +X143009882Y-72928059D01* +X143009880Y-72928055D01* +X143007021Y-72921153D01* +X144799500Y-72921153D01* +X144799500Y-73078846D01* +X144830261Y-73233489D01* +X144830264Y-73233501D01* +X144890602Y-73379172D01* +X144890609Y-73379185D01* +X144978210Y-73510288D01* +X144978213Y-73510292D01* +X145089707Y-73621786D01* +X145089711Y-73621789D01* +X145220814Y-73709390D01* +X145220827Y-73709397D01* +X145366498Y-73769735D01* +X145366503Y-73769737D01* +X145521153Y-73800499D01* +X145521156Y-73800500D01* +X145521158Y-73800500D01* +X145678844Y-73800500D01* +X145678845Y-73800499D01* +X145833497Y-73769737D01* +X145979179Y-73709394D01* +X146110289Y-73621789D01* +X146221789Y-73510289D01* +X146309394Y-73379179D01* +X146316859Y-73361158D01* +X146325416Y-73340498D01* +X146369737Y-73233497D01* +X146400500Y-73078842D01* +X146400500Y-72921158D01* +X146400500Y-72921155D01* +X146400499Y-72921153D01* +X146380022Y-72818210D01* +X146369737Y-72766503D01* +X146369735Y-72766498D01* +X146309397Y-72620827D01* +X146309390Y-72620814D01* +X146221789Y-72489711D01* +X146221786Y-72489707D01* +X146110292Y-72378213D01* +X146110288Y-72378210D01* +X145979185Y-72290609D01* +X145979172Y-72290602D01* +X145833501Y-72230264D01* +X145833489Y-72230261D01* +X145678845Y-72199500D01* +X145678842Y-72199500D01* +X145521158Y-72199500D01* +X145521155Y-72199500D01* +X145366510Y-72230261D01* +X145366498Y-72230264D01* +X145220827Y-72290602D01* +X145220814Y-72290609D01* +X145089711Y-72378210D01* +X145089707Y-72378213D01* +X144978213Y-72489707D01* +X144978210Y-72489711D01* +X144890609Y-72620814D01* +X144890602Y-72620827D01* +X144830264Y-72766498D01* +X144830261Y-72766510D01* +X144799500Y-72921153D01* +X143007021Y-72921153D01* +X142920819Y-72713039D01* +X142920811Y-72713023D01* +X142804446Y-72511475D01* +X142804443Y-72511470D01* +X142804442Y-72511468D01* +X142702192Y-72378213D01* +X142662757Y-72326820D01* +X142662751Y-72326813D01* +X142498186Y-72162248D01* +X142498179Y-72162242D01* +X142313540Y-72020564D01* +X142313538Y-72020562D01* +X142313532Y-72020558D01* +X142313527Y-72020555D01* +X142313524Y-72020553D01* +X142111976Y-71904188D01* +X142111960Y-71904180D01* +X141896947Y-71815120D01* +X141729539Y-71770263D01* +X141672126Y-71754879D01* +X141672125Y-71754878D01* +X141672122Y-71754878D01* +X141441382Y-71724501D01* +X141441377Y-71724500D01* +X141441372Y-71724500D01* +X141208628Y-71724500D01* +X141208622Y-71724500D01* +X141208617Y-71724501D01* +X140977877Y-71754878D01* +X140753052Y-71815120D01* +X140538039Y-71904180D01* +X140538023Y-71904188D01* +X140336475Y-72020553D01* +X140336459Y-72020564D01* +X140151820Y-72162242D01* +X140151813Y-72162248D01* +X139987248Y-72326813D01* +X139987242Y-72326820D01* +X139845564Y-72511459D01* +X139845553Y-72511475D01* +X139729188Y-72713023D01* +X139729180Y-72713039D01* +X139640120Y-72928052D01* +X139579878Y-73152877D01* +X139549501Y-73383617D01* +X139549500Y-73383634D01* +X139549500Y-73616365D01* +X139549501Y-73616382D01* +X139579878Y-73847122D01* +X139640120Y-74071947D01* +X139729180Y-74286960D01* +X139729188Y-74286976D01* +X139845553Y-74488524D01* +X139845564Y-74488540D01* +X139987242Y-74673179D01* +X139987248Y-74673186D01* +X140151813Y-74837751D01* +X140151819Y-74837756D01* +X140336468Y-74979442D01* +X140336475Y-74979446D01* +X140538023Y-75095811D01* +X140538039Y-75095819D01* +X140753052Y-75184879D01* +X140753054Y-75184879D01* +X140753060Y-75184882D01* +X140977874Y-75245121D01* +X141208628Y-75275500D01* +X141208635Y-75275500D01* +X141441365Y-75275500D01* +X141441372Y-75275500D01* +X141672126Y-75245121D01* +X141896940Y-75184882D01* +X142028149Y-75130534D01* +X142111960Y-75095819D01* +X142111961Y-75095817D01* +X142111969Y-75095815D01* +X142278478Y-74999680D01* +X142346375Y-74983208D01* +X142412402Y-75006060D01* +X142455593Y-75060981D01* +X142462235Y-75130534D01* +X142440796Y-75179951D01* +X142425704Y-75200724D01* +X142316728Y-75414598D01* +X142242549Y-75642894D01* +X142205000Y-75879974D01* +X142205000Y-76120025D01* +X142242549Y-76357105D01* +X142316728Y-76585401D01* +X142425705Y-76799277D01* +X142489441Y-76887003D01* +X142489443Y-76887003D01* +X143226624Y-76149821D01* +X143240778Y-76202642D01* +X143309896Y-76322357D01* +X143407643Y-76420104D01* +X143527358Y-76489222D01* +X143580177Y-76503375D01* +X142810679Y-77272871D01* +X142788175Y-77298654D01* +X142736204Y-77336413D01* +X142566416Y-77506201D01* +X142425276Y-77700463D01* +X142316265Y-77914406D01* +X142242063Y-78142777D01* +X142204499Y-78379943D01* +X142204117Y-78384804D01* +X142201821Y-78384623D01* +X142184815Y-78442539D01* +X142132011Y-78488294D01* +X142080500Y-78499500D01* +X142021155Y-78499500D01* +X141866510Y-78530261D01* +X141866498Y-78530264D01* +X141720827Y-78590602D01* +X141720814Y-78590609D01* +X141589711Y-78678210D01* +X141589707Y-78678213D01* +X141478213Y-78789707D01* +X141478210Y-78789711D01* +X141390609Y-78920814D01* +X141390602Y-78920827D01* +X141330264Y-79066498D01* +X141330261Y-79066510D01* +X141299500Y-79221153D01* +X141299500Y-79378846D01* +X141330261Y-79533489D01* +X141330264Y-79533501D01* +X141390602Y-79679172D01* +X141390609Y-79679185D01* +X141478210Y-79810288D01* +X141478213Y-79810292D01* +X141589707Y-79921786D01* +X141589711Y-79921789D01* +X141720814Y-80009390D01* +X141720827Y-80009397D01* +X141866498Y-80069735D01* +X141866503Y-80069737D01* +X141972298Y-80090781D01* +X142021153Y-80100499D01* +X142021156Y-80100500D01* +X142021158Y-80100500D01* +X142178844Y-80100500D01* +X142259007Y-80084554D01* +X142328598Y-80090781D01* +X142383776Y-80133643D01* +X142407021Y-80199533D01* +X142393684Y-80262466D01* +X142316265Y-80414406D01* +X142242063Y-80642777D01* +X142204500Y-80879941D01* +X142204500Y-81120058D01* +X142242063Y-81357222D01* +X142316265Y-81585593D01* +X142425278Y-81799540D01* +X142439730Y-81819431D01* +X142463211Y-81885237D01* +X142447386Y-81953291D01* +X142397281Y-82001986D01* +X142328803Y-82015862D01* +X142277413Y-81999704D01* +X142111976Y-81904188D01* +X142111960Y-81904180D01* +X141896947Y-81815120D01* +X141672122Y-81754878D01* +X141441382Y-81724501D01* +X141441377Y-81724500D01* +X141441372Y-81724500D01* +X141208628Y-81724500D01* +X141208622Y-81724500D01* +X141208617Y-81724501D01* +X140977877Y-81754878D01* +X140753052Y-81815120D01* +X140538039Y-81904180D01* +X140538023Y-81904188D01* +X140336475Y-82020553D01* +X140336459Y-82020564D01* +X140151820Y-82162242D01* +X140151813Y-82162248D01* +X139987248Y-82326813D01* +X139987242Y-82326820D01* +X139845564Y-82511459D01* +X139845553Y-82511475D01* +X139729188Y-82713023D01* +X139729180Y-82713039D01* +X139640121Y-82928051D01* +X139640121Y-82928052D01* +X139640118Y-82928060D01* +X139623360Y-82990602D01* +X139608374Y-83046528D01* +X139572008Y-83106188D01* +X139509161Y-83136716D01* +X139439785Y-83128421D01* +X139400918Y-83102114D01* +X139308940Y-83010136D01* +X139308935Y-83010132D01* +X139101950Y-82859750D01* +X139101949Y-82859749D01* +X139101947Y-82859748D01* +X139028910Y-82822533D01* +X138873975Y-82743589D01* +X138873972Y-82743588D01* +X138630640Y-82664526D01* +X138504284Y-82644513D01* +X138377930Y-82624500D01* +X138122070Y-82624500D01* +X138037833Y-82637842D01* +X137869359Y-82664526D01* +X137626027Y-82743588D01* +X137626024Y-82743589D01* +X137398049Y-82859750D01* +X137191064Y-83010132D01* +X137191059Y-83010136D01* +X137010136Y-83191059D01* +X137010132Y-83191064D01* +X136859750Y-83398049D01* +X136743589Y-83626024D01* +X136743588Y-83626027D01* +X136664526Y-83869359D01* +X136624500Y-84122070D01* +X133375500Y-84122070D01* +X133335474Y-83869361D01* +X133273682Y-83679184D01* +X133256411Y-83626027D01* +X133256410Y-83626024D01* +X133209260Y-83533488D01* +X133140252Y-83398053D01* +X133061814Y-83290092D01* +X132989867Y-83191064D01* +X132989863Y-83191059D01* +X132808940Y-83010136D01* +X132808935Y-83010132D01* +X132601950Y-82859750D01* +X132601949Y-82859749D01* +X132601947Y-82859748D01* +X132528910Y-82822533D01* +X132373975Y-82743589D01* +X132373972Y-82743588D01* +X132130640Y-82664526D01* +X132004284Y-82644513D01* +X131877930Y-82624500D01* +X131622070Y-82624500D01* +X131537833Y-82637842D01* +X131369359Y-82664526D01* +X131126027Y-82743588D01* +X131126024Y-82743589D01* +X130898049Y-82859750D01* +X130691065Y-83010131D01* +X130599080Y-83102116D01* +X130537756Y-83135600D01* +X130468065Y-83130616D01* +X130412131Y-83088744D01* +X130391626Y-83046532D01* +X130359882Y-82928060D01* +X130359879Y-82928052D01* +X130270819Y-82713039D01* +X130270811Y-82713023D01* +X130154446Y-82511475D01* +X130154442Y-82511468D01* +X130012756Y-82326819D01* +X130012751Y-82326813D01* +X129848186Y-82162248D01* +X129848179Y-82162242D01* +X129663540Y-82020564D01* +X129663538Y-82020562D01* +X129663532Y-82020558D01* +X129663527Y-82020555D01* +X129663524Y-82020553D01* +X129461976Y-81904188D01* +X129461960Y-81904180D01* +X129246947Y-81815120D01* +X129022122Y-81754878D01* +X128791382Y-81724501D01* +X128791377Y-81724500D01* +X128791372Y-81724500D01* +X128558628Y-81724500D01* +X128558622Y-81724500D01* +X128558617Y-81724501D01* +X128327877Y-81754878D01* +X128103052Y-81815120D01* +X127888039Y-81904180D01* +X127888023Y-81904188D01* +X127686475Y-82020553D01* +X127686459Y-82020564D01* +X127501820Y-82162242D01* +X127501813Y-82162248D01* +X127337248Y-82326813D01* +X127337242Y-82326820D01* +X127195564Y-82511459D01* +X127195553Y-82511475D01* +X127079188Y-82713023D01* +X127079180Y-82713039D01* +X126990120Y-82928052D01* +X126929878Y-83152877D01* +X126899501Y-83383617D01* +X126899500Y-83383634D01* +X124835411Y-83383634D01* +X124833427Y-83378843D01* +X124809397Y-83320826D01* +X124809390Y-83320814D01* +X124721789Y-83189711D01* +X124721786Y-83189707D01* +X124610292Y-83078213D01* +X124610288Y-83078210D01* +X124479185Y-82990609D01* +X124479172Y-82990602D01* +X124333501Y-82930264D01* +X124333489Y-82930261D01* +X124178845Y-82899500D01* +X124178842Y-82899500D01* +X124021158Y-82899500D01* +X124021155Y-82899500D01* +X123866510Y-82930261D01* +X123866498Y-82930264D01* +X123720827Y-82990602D01* +X123720814Y-82990609D01* +X123589711Y-83078210D01* +X123589707Y-83078213D01* +X123478213Y-83189707D01* +X123478210Y-83189711D01* +X123390609Y-83320814D01* +X123390602Y-83320827D01* +X123330264Y-83466498D01* +X123330261Y-83466510D01* +X123299500Y-83621153D01* +X120250500Y-83621153D01* +X120250500Y-81443995D01* +X121099499Y-81443995D01* +X121126418Y-81579322D01* +X121126421Y-81579332D01* +X121179221Y-81706804D01* +X121179228Y-81706817D01* +X121255885Y-81821541D01* +X121255888Y-81821545D01* +X121353454Y-81919111D01* +X121353458Y-81919114D01* +X121468182Y-81995771D01* +X121468195Y-81995778D01* +X121595667Y-82048578D01* +X121595672Y-82048580D01* +X121595676Y-82048580D01* +X121595677Y-82048581D01* +X121731004Y-82075500D01* +X121731007Y-82075500D01* +X121868995Y-82075500D01* +X121960041Y-82057389D01* +X122004328Y-82048580D01* +X122131811Y-81995775D01* +X122246542Y-81919114D01* +X122344114Y-81821542D01* +X122420775Y-81706811D01* +X122473580Y-81579328D01* +X122500500Y-81443993D01* +X122500500Y-81306007D01* +X122500500Y-81306004D01* +X122473581Y-81170677D01* +X122473580Y-81170676D01* +X122473580Y-81170672D01* +X122473578Y-81170667D01* +X122420778Y-81043195D01* +X122420771Y-81043182D01* +X122344114Y-80928458D01* +X122344111Y-80928454D01* +X122246545Y-80830888D01* +X122246541Y-80830885D01* +X122131817Y-80754228D01* +X122131804Y-80754221D01* +X122004332Y-80701421D01* +X122004322Y-80701418D01* +X121868995Y-80674500D01* +X121868993Y-80674500D01* +X121731007Y-80674500D01* +X121731005Y-80674500D01* +X121595677Y-80701418D01* +X121595667Y-80701421D01* +X121468195Y-80754221D01* +X121468182Y-80754228D01* +X121353458Y-80830885D01* +X121353454Y-80830888D01* +X121255888Y-80928454D01* +X121255885Y-80928458D01* +X121179228Y-81043182D01* +X121179221Y-81043195D01* +X121126421Y-81170667D01* +X121126418Y-81170677D01* +X121099500Y-81306004D01* +X121099500Y-81306007D01* +X121099500Y-81443993D01* +X121099500Y-81443995D01* +X121099499Y-81443995D01* +X120250500Y-81443995D01* +X120250500Y-75693995D01* +X121099499Y-75693995D01* +X121126418Y-75829322D01* +X121126421Y-75829332D01* +X121179221Y-75956804D01* +X121179228Y-75956817D01* +X121255885Y-76071541D01* +X121255888Y-76071545D01* +X121353454Y-76169111D01* +X121353458Y-76169114D01* +X121468182Y-76245771D01* +X121468195Y-76245778D01* +X121595667Y-76298578D01* +X121595672Y-76298580D01* +X121595676Y-76298580D01* +X121595677Y-76298581D01* +X121731004Y-76325500D01* +X121731007Y-76325500D01* +X121868995Y-76325500D01* +X121960041Y-76307389D01* +X122004328Y-76298580D01* +X122131811Y-76245775D01* +X122246542Y-76169114D01* +X122344114Y-76071542D01* +X122420775Y-75956811D01* +X122460398Y-75861153D01* +X135484500Y-75861153D01* +X135484500Y-76018846D01* +X135515261Y-76173489D01* +X135515264Y-76173501D01* +X135575602Y-76319172D01* +X135575609Y-76319185D01* +X135663210Y-76450288D01* +X135663213Y-76450292D01* +X135774707Y-76561786D01* +X135774711Y-76561789D01* +X135905814Y-76649390D01* +X135905827Y-76649397D01* +X136051498Y-76709735D01* +X136051503Y-76709737D01* +X136206153Y-76740499D01* +X136206156Y-76740500D01* +X136206158Y-76740500D01* +X136363844Y-76740500D01* +X136363845Y-76740499D01* +X136518497Y-76709737D01* +X136664179Y-76649394D01* +X136795289Y-76561789D01* +X136906789Y-76450289D01* +X136994394Y-76319179D01* +X137054737Y-76173497D01* +X137085500Y-76018842D01* +X137085500Y-75861158D01* +X137085500Y-75861155D01* +X137085499Y-75861153D01* +X137079169Y-75829332D01* +X137054737Y-75706503D01* +X137042783Y-75677643D01* +X136994397Y-75560827D01* +X136994390Y-75560814D01* +X136906789Y-75429711D01* +X136906786Y-75429707D01* +X136795292Y-75318213D01* +X136795288Y-75318210D01* +X136664185Y-75230609D01* +X136664172Y-75230602D01* +X136518501Y-75170264D01* +X136518489Y-75170261D01* +X136363845Y-75139500D01* +X136363842Y-75139500D01* +X136206158Y-75139500D01* +X136206155Y-75139500D01* +X136051510Y-75170261D01* +X136051498Y-75170264D01* +X135905827Y-75230602D01* +X135905814Y-75230609D01* +X135774711Y-75318210D01* +X135774707Y-75318213D01* +X135663213Y-75429707D01* +X135663210Y-75429711D01* +X135575609Y-75560814D01* +X135575602Y-75560827D01* +X135515264Y-75706498D01* +X135515261Y-75706510D01* +X135484500Y-75861153D01* +X122460398Y-75861153D01* +X122473580Y-75829328D01* +X122500500Y-75693993D01* +X122500500Y-75556007D01* +X122500500Y-75556004D01* +X122473581Y-75420677D01* +X122473580Y-75420676D01* +X122473580Y-75420672D01* +X122471064Y-75414598D01* +X122420778Y-75293195D01* +X122420771Y-75293182D01* +X122344114Y-75178458D01* +X122344111Y-75178454D01* +X122246545Y-75080888D01* +X122246541Y-75080885D01* +X122131817Y-75004228D01* +X122131804Y-75004221D01* +X122004332Y-74951421D01* +X122004322Y-74951418D01* +X121868995Y-74924500D01* +X121868993Y-74924500D01* +X121731007Y-74924500D01* +X121731005Y-74924500D01* +X121595677Y-74951418D01* +X121595667Y-74951421D01* +X121468195Y-75004221D01* +X121468182Y-75004228D01* +X121353458Y-75080885D01* +X121353454Y-75080888D01* +X121255888Y-75178454D01* +X121255885Y-75178458D01* +X121179228Y-75293182D01* +X121179221Y-75293195D01* +X121126421Y-75420667D01* +X121126418Y-75420677D01* +X121099500Y-75556004D01* +X121099500Y-75556007D01* +X121099500Y-75693993D01* +X121099500Y-75693995D01* +X121099499Y-75693995D01* +X120250500Y-75693995D01* +X120250500Y-73383634D01* +X126899500Y-73383634D01* +X126899500Y-73616365D01* +X126899501Y-73616382D01* +X126929878Y-73847122D01* +X126990120Y-74071947D01* +X127079180Y-74286960D01* +X127079188Y-74286976D01* +X127195553Y-74488524D01* +X127195564Y-74488540D01* +X127337242Y-74673179D01* +X127337248Y-74673186D01* +X127501813Y-74837751D01* +X127501819Y-74837756D01* +X127686468Y-74979442D01* +X127686475Y-74979446D01* +X127888023Y-75095811D01* +X127888039Y-75095819D01* +X128103052Y-75184879D01* +X128103054Y-75184879D01* +X128103060Y-75184882D01* +X128327874Y-75245121D01* +X128558628Y-75275500D01* +X128558635Y-75275500D01* +X128791365Y-75275500D01* +X128791372Y-75275500D01* +X129022126Y-75245121D01* +X129246940Y-75184882D01* +X129378149Y-75130534D01* +X129461960Y-75095819D01* +X129461963Y-75095817D01* +X129461969Y-75095815D01* +X129663532Y-74979442D01* +X129848181Y-74837756D01* +X130012756Y-74673181D01* +X130154442Y-74488532D01* +X130270815Y-74286969D01* +X130327802Y-74149390D01* +X130359879Y-74071947D01* +X130359878Y-74071947D01* +X130359882Y-74071940D01* +X130420121Y-73847126D01* +X130450500Y-73616372D01* +X130450500Y-73383628D01* +X130449913Y-73379172D01* +X130448871Y-73371250D01* +X130447542Y-73361153D01* +X130984500Y-73361153D01* +X130984500Y-73518846D01* +X131015261Y-73673489D01* +X131015264Y-73673501D01* +X131075602Y-73819172D01* +X131075609Y-73819185D01* +X131163210Y-73950288D01* +X131163213Y-73950292D01* +X131274707Y-74061786D01* +X131274711Y-74061789D01* +X131405814Y-74149390D01* +X131405827Y-74149397D01* +X131551498Y-74209735D01* +X131551503Y-74209737D01* +X131706153Y-74240499D01* +X131706156Y-74240500D01* +X131706158Y-74240500D01* +X131863844Y-74240500D01* +X131863845Y-74240499D01* +X132018497Y-74209737D01* +X132164179Y-74149394D01* +X132295289Y-74061789D01* +X132406789Y-73950289D01* +X132494394Y-73819179D01* +X132554737Y-73673497D01* +X132585500Y-73518842D01* +X132585500Y-73361158D01* +X132585500Y-73361155D01* +X132585499Y-73361153D01* +X132563268Y-73249393D01* +X132554737Y-73206503D01* +X132536216Y-73161788D01* +X132494397Y-73060827D01* +X132494390Y-73060814D01* +X132406789Y-72929711D01* +X132406786Y-72929707D01* +X132295292Y-72818213D01* +X132295288Y-72818210D01* +X132164185Y-72730609D01* +X132164172Y-72730602D01* +X132018501Y-72670264D01* +X132018489Y-72670261D01* +X131863845Y-72639500D01* +X131863842Y-72639500D01* +X131706158Y-72639500D01* +X131706155Y-72639500D01* +X131551510Y-72670261D01* +X131551498Y-72670264D01* +X131405827Y-72730602D01* +X131405814Y-72730609D01* +X131274711Y-72818210D01* +X131274707Y-72818213D01* +X131163213Y-72929707D01* +X131163210Y-72929711D01* +X131075609Y-73060814D01* +X131075602Y-73060827D01* +X131015264Y-73206498D01* +X131015261Y-73206510D01* +X130984500Y-73361153D01* +X130447542Y-73361153D01* +X130427181Y-73206503D01* +X130420121Y-73152874D01* +X130359882Y-72928060D01* +X130357021Y-72921153D01* +X130270819Y-72713039D01* +X130270814Y-72713030D01* +X130246123Y-72670264D01* +X130154442Y-72511468D01* +X130115833Y-72461152D01* +X137684500Y-72461152D01* +X137684500Y-72618845D01* +X137715261Y-72773488D01* +X137715264Y-72773500D01* +X137775602Y-72919171D01* +X137775609Y-72919184D01* +X137863210Y-73050287D01* +X137863213Y-73050291D01* +X137974707Y-73161785D01* +X137974711Y-73161788D01* +X138105814Y-73249389D01* +X138105827Y-73249396D01* +X138251498Y-73309734D01* +X138251503Y-73309736D01* +X138406153Y-73340498D01* +X138406156Y-73340499D01* +X138406158Y-73340499D01* +X138563844Y-73340499D01* +X138563845Y-73340498D01* +X138718497Y-73309736D01* +X138761911Y-73291753D01* +X138826482Y-73265008D01* +X138864172Y-73249396D01* +X138864172Y-73249395D01* +X138864179Y-73249393D01* +X138995289Y-73161788D01* +X139106789Y-73050288D01* +X139194394Y-72919178D01* +X139254737Y-72773496D01* +X139285500Y-72618841D01* +X139285500Y-72461157D01* +X139285500Y-72461154D01* +X139285499Y-72461152D01* +X139277669Y-72421789D01* +X139254737Y-72306502D01* +X139248151Y-72290602D01* +X139194397Y-72160826D01* +X139194390Y-72160813D01* +X139106789Y-72029710D01* +X139106786Y-72029706D01* +X138995292Y-71918212D01* +X138995288Y-71918209D01* +X138864185Y-71830608D01* +X138864172Y-71830601D01* +X138718501Y-71770263D01* +X138718489Y-71770260D01* +X138563845Y-71739499D01* +X138563842Y-71739499D01* +X138406158Y-71739499D01* +X138406155Y-71739499D01* +X138251510Y-71770260D01* +X138251498Y-71770263D01* +X138105827Y-71830601D01* +X138105814Y-71830608D01* +X137974711Y-71918209D01* +X137974707Y-71918212D01* +X137863213Y-72029706D01* +X137863210Y-72029710D01* +X137775609Y-72160813D01* +X137775602Y-72160826D01* +X137715264Y-72306497D01* +X137715261Y-72306509D01* +X137684500Y-72461152D01* +X130115833Y-72461152D01* +X130052192Y-72378213D01* +X130012757Y-72326820D01* +X130012751Y-72326813D01* +X129848186Y-72162248D01* +X129848179Y-72162242D01* +X129663540Y-72020564D01* +X129663538Y-72020562D01* +X129663532Y-72020558D01* +X129663527Y-72020555D01* +X129663524Y-72020553D01* +X129461976Y-71904188D01* +X129461960Y-71904180D01* +X129246947Y-71815120D01* +X129079539Y-71770263D01* +X129022126Y-71754879D01* +X129022125Y-71754878D01* +X129022122Y-71754878D01* +X128791382Y-71724501D01* +X128791377Y-71724500D01* +X128791372Y-71724500D01* +X128558628Y-71724500D01* +X128558622Y-71724500D01* +X128558617Y-71724501D01* +X128327877Y-71754878D01* +X128103052Y-71815120D01* +X127888039Y-71904180D01* +X127888023Y-71904188D01* +X127686475Y-72020553D01* +X127686459Y-72020564D01* +X127501820Y-72162242D01* +X127501813Y-72162248D01* +X127337248Y-72326813D01* +X127337242Y-72326820D01* +X127195564Y-72511459D01* +X127195553Y-72511475D01* +X127079188Y-72713023D01* +X127079180Y-72713039D01* +X126990120Y-72928052D01* +X126929878Y-73152877D01* +X126899501Y-73383617D01* +X126899500Y-73383634D01* +X120250500Y-73383634D01* +X120250500Y-71443995D01* +X121099499Y-71443995D01* +X121126418Y-71579322D01* +X121126421Y-71579332D01* +X121179221Y-71706804D01* +X121179228Y-71706817D01* +X121255885Y-71821541D01* +X121255888Y-71821545D01* +X121353454Y-71919111D01* +X121353458Y-71919114D01* +X121468182Y-71995771D01* +X121468195Y-71995778D01* +X121595667Y-72048578D01* +X121595672Y-72048580D01* +X121595676Y-72048580D01* +X121595677Y-72048581D01* +X121731004Y-72075500D01* +X121731007Y-72075500D01* +X121868995Y-72075500D01* +X121960041Y-72057389D01* +X122004328Y-72048580D01* +X122131811Y-71995775D01* +X122246542Y-71919114D01* +X122344114Y-71821542D01* +X122411192Y-71721153D01* +X123399500Y-71721153D01* +X123399500Y-71878846D01* +X123430261Y-72033489D01* +X123430264Y-72033501D01* +X123490602Y-72179172D01* +X123490609Y-72179185D01* +X123578210Y-72310288D01* +X123578213Y-72310292D01* +X123689707Y-72421786D01* +X123689711Y-72421789D01* +X123820814Y-72509390D01* +X123820827Y-72509397D01* +X123966498Y-72569735D01* +X123966503Y-72569737D01* +X124121153Y-72600499D01* +X124121156Y-72600500D01* +X124121158Y-72600500D01* +X124278844Y-72600500D01* +X124278845Y-72600499D01* +X124433497Y-72569737D01* +X124579179Y-72509394D01* +X124710289Y-72421789D01* +X124821789Y-72310289D01* +X124909394Y-72179179D01* +X124916410Y-72162242D01* +X124969735Y-72033501D01* +X124969737Y-72033497D01* +X125000500Y-71878842D01* +X125000500Y-71721158D01* +X125000500Y-71721155D01* +X125000499Y-71721153D01* +X124969738Y-71566510D01* +X124969737Y-71566503D01* +X124942398Y-71500500D01* +X124909397Y-71420827D01* +X124909390Y-71420814D01* +X124821789Y-71289711D01* +X124821786Y-71289707D01* +X124710292Y-71178213D01* +X124710288Y-71178210D01* +X124579185Y-71090609D01* +X124579176Y-71090604D01* +X124548403Y-71077858D01* +X124548401Y-71077857D01* +X124433501Y-71030264D01* +X124433489Y-71030261D01* +X124278845Y-70999500D01* +X124278842Y-70999500D01* +X124121158Y-70999500D01* +X124121155Y-70999500D01* +X123966510Y-71030261D01* +X123966498Y-71030264D01* +X123820827Y-71090602D01* +X123820814Y-71090609D01* +X123689711Y-71178210D01* +X123689707Y-71178213D01* +X123578213Y-71289707D01* +X123578210Y-71289711D01* +X123490609Y-71420814D01* +X123490602Y-71420827D01* +X123430264Y-71566498D01* +X123430261Y-71566510D01* +X123399500Y-71721153D01* +X122411192Y-71721153D01* +X122420775Y-71706811D01* +X122473580Y-71579328D01* +X122500500Y-71443993D01* +X122500500Y-71306007D01* +X122500500Y-71306004D01* +X122473581Y-71170677D01* +X122473580Y-71170676D01* +X122473580Y-71170672D01* +X122446230Y-71104643D01* +X122420778Y-71043195D01* +X122420771Y-71043182D01* +X122344114Y-70928458D01* +X122344111Y-70928454D01* +X122246545Y-70830888D01* +X122246541Y-70830885D01* +X122131817Y-70754228D01* +X122131804Y-70754221D01* +X122004332Y-70701421D01* +X122004322Y-70701418D01* +X121868995Y-70674500D01* +X121868993Y-70674500D01* +X121731007Y-70674500D01* +X121731005Y-70674500D01* +X121595677Y-70701418D01* +X121595667Y-70701421D01* +X121468195Y-70754221D01* +X121468182Y-70754228D01* +X121353458Y-70830885D01* +X121353454Y-70830888D01* +X121255888Y-70928454D01* +X121255885Y-70928458D01* +X121179228Y-71043182D01* +X121179221Y-71043195D01* +X121126421Y-71170667D01* +X121126418Y-71170677D01* +X121099500Y-71306004D01* +X121099500Y-71306007D01* +X121099500Y-71443993D01* +X121099500Y-71443995D01* +X121099499Y-71443995D01* +X120250500Y-71443995D01* +X120250500Y-69649974D01* +X130975000Y-69649974D01* +X130975000Y-69890025D01* +X131012549Y-70127105D01* +X131086728Y-70355401D01* +X131195705Y-70569277D01* +X131259441Y-70657003D01* +X131259443Y-70657003D01* +X131996624Y-69919822D01* +X132010778Y-69972642D01* +X132079896Y-70092357D01* +X132177643Y-70190104D01* +X132297358Y-70259222D01* +X132350177Y-70273375D01* +X131612994Y-71010556D01* +X131612995Y-71010557D01* +X131700722Y-71074294D01* +X131914598Y-71183271D01* +X132142894Y-71257450D01* +X132379975Y-71295000D01* +X132620025Y-71295000D01* +X132857105Y-71257450D01* +X133085401Y-71183271D01* +X133299274Y-71074296D01* +X133387003Y-71010556D01* +X133387004Y-71010556D01* +X132649822Y-70273375D01* +X132702642Y-70259222D01* +X132822357Y-70190104D01* +X132920104Y-70092357D01* +X132989222Y-69972642D01* +X133003374Y-69919822D01* +X133772897Y-70689345D01* +X133798654Y-70711824D01* +X133836414Y-70763796D01* +X134006204Y-70933586D01* +X134200464Y-71074724D01* +X134259183Y-71104643D01* +X134414406Y-71183734D01* +X134414408Y-71183734D01* +X134414411Y-71183736D01* +X134642778Y-71257937D01* +X134879941Y-71295500D01* +X134879942Y-71295500D01* +X135120058Y-71295500D01* +X135120059Y-71295500D01* +X135357222Y-71257937D01* +X135585589Y-71183736D01* +X135799536Y-71074724D01* +X135993796Y-70933586D01* +X136162319Y-70765063D01* +X136223642Y-70731578D01* +X136293334Y-70736562D01* +X136337681Y-70765063D01* +X136506204Y-70933586D01* +X136700464Y-71074724D01* +X136759183Y-71104643D01* +X136914406Y-71183734D01* +X136914408Y-71183734D01* +X136914411Y-71183736D01* +X137142778Y-71257937D01* +X137379941Y-71295500D01* +X137379942Y-71295500D01* +X137620058Y-71295500D01* +X137620059Y-71295500D01* +X137857222Y-71257937D01* +X138085589Y-71183736D01* +X138085594Y-71183733D01* +X138085598Y-71183732D01* +X138267075Y-71091264D01* +X138335744Y-71078367D01* +X138400484Y-71104643D01* +X138426472Y-71132857D01* +X138478210Y-71210288D01* +X138478213Y-71210292D01* +X138589707Y-71321786D01* +X138589711Y-71321789D01* +X138720814Y-71409390D01* +X138720827Y-71409397D01* +X138866498Y-71469735D01* +X138866503Y-71469737D01* +X139021153Y-71500499D01* +X139021156Y-71500500D01* +X139021158Y-71500500D01* +X139178844Y-71500500D01* +X139178845Y-71500499D01* +X139333497Y-71469737D01* +X139395644Y-71443995D01* +X147499499Y-71443995D01* +X147526418Y-71579322D01* +X147526421Y-71579332D01* +X147579221Y-71706804D01* +X147579228Y-71706817D01* +X147655885Y-71821541D01* +X147655888Y-71821545D01* +X147753454Y-71919111D01* +X147753458Y-71919114D01* +X147868182Y-71995771D01* +X147868195Y-71995778D01* +X147995667Y-72048578D01* +X147995672Y-72048580D01* +X147995676Y-72048580D01* +X147995677Y-72048581D01* +X148131004Y-72075500D01* +X148131007Y-72075500D01* +X148268995Y-72075500D01* +X148360041Y-72057389D01* +X148404328Y-72048580D01* +X148531811Y-71995775D01* +X148646542Y-71919114D01* +X148744114Y-71821542D01* +X148820775Y-71706811D01* +X148873580Y-71579328D01* +X148900500Y-71443993D01* +X148900500Y-71306007D01* +X148900500Y-71306004D01* +X148873581Y-71170677D01* +X148873580Y-71170676D01* +X148873580Y-71170672D01* +X148846230Y-71104643D01* +X148820778Y-71043195D01* +X148820771Y-71043182D01* +X148744114Y-70928458D01* +X148744111Y-70928454D01* +X148646545Y-70830888D01* +X148646541Y-70830885D01* +X148531817Y-70754228D01* +X148531804Y-70754221D01* +X148404332Y-70701421D01* +X148404322Y-70701418D01* +X148268995Y-70674500D01* +X148268993Y-70674500D01* +X148131007Y-70674500D01* +X148131005Y-70674500D01* +X147995677Y-70701418D01* +X147995667Y-70701421D01* +X147868195Y-70754221D01* +X147868182Y-70754228D01* +X147753458Y-70830885D01* +X147753454Y-70830888D01* +X147655888Y-70928454D01* +X147655885Y-70928458D01* +X147579228Y-71043182D01* +X147579221Y-71043195D01* +X147526421Y-71170667D01* +X147526418Y-71170677D01* +X147499500Y-71306004D01* +X147499500Y-71306007D01* +X147499500Y-71443993D01* +X147499500Y-71443995D01* +X147499499Y-71443995D01* +X139395644Y-71443995D01* +X139451592Y-71420821D01* +X139479172Y-71409397D01* +X139479172Y-71409396D01* +X139479179Y-71409394D01* +X139610289Y-71321789D01* +X139642371Y-71289707D01* +X139719845Y-71212234D01* +X139721786Y-71210292D01* +X139721789Y-71210289D01* +X139809394Y-71079179D01* +X139811418Y-71074294D01* +X139829655Y-71030264D01* +X139869737Y-70933497D01* +X139900500Y-70778842D01* +X139900500Y-70621158D01* +X139900500Y-70621155D01* +X139900499Y-70621153D01* +X139869738Y-70466510D01* +X139869737Y-70466503D01* +X139869735Y-70466498D01* +X139809397Y-70320827D01* +X139809390Y-70320814D01* +X139721789Y-70189711D01* +X139721786Y-70189707D01* +X139610292Y-70078213D01* +X139610288Y-70078210D01* +X139479185Y-69990609D01* +X139479172Y-69990602D01* +X139333501Y-69930264D01* +X139333489Y-69930261D01* +X139178845Y-69899500D01* +X139178842Y-69899500D01* +X139149500Y-69899500D01* +X139082461Y-69879815D01* +X139036706Y-69827011D01* +X139025500Y-69775500D01* +X139025500Y-69649941D01* +X139012420Y-69567358D01* +X138987937Y-69412778D01* +X138913736Y-69184411D01* +X138913734Y-69184408D01* +X138913734Y-69184406D01* +X138804723Y-68970463D01* +X138741174Y-68882995D01* +X138663586Y-68776204D01* +X138493796Y-68606414D01* +X138299536Y-68465276D01* +X138085593Y-68356265D01* +X137857222Y-68282063D01* +X137620059Y-68244500D01* +X137379941Y-68244500D01* +X137261359Y-68263281D01* +X137142777Y-68282063D01* +X136914406Y-68356265D01* +X136700463Y-68465276D01* +X136506201Y-68606416D01* +X136337681Y-68774937D01* +X136276358Y-68808422D01* +X136206666Y-68803438D01* +X136162319Y-68774937D01* +X135993798Y-68606416D01* +X135993796Y-68606414D01* +X135799536Y-68465276D01* +X135585593Y-68356265D01* +X135357222Y-68282063D01* +X135120059Y-68244500D01* +X134879941Y-68244500D01* +X134761359Y-68263281D01* +X134642777Y-68282063D01* +X134414406Y-68356265D01* +X134200463Y-68465276D01* +X134006201Y-68606416D01* +X133836413Y-68776204D01* +X133798654Y-68828175D01* +X133780544Y-68842139D01* +X133780978Y-68842573D01* +X133003374Y-69620176D01* +X132989222Y-69567358D01* +X132920104Y-69447643D01* +X132822357Y-69349896D01* +X132702642Y-69280778D01* +X132649821Y-69266624D01* +X133387003Y-68529443D01* +X133387003Y-68529441D01* +X133299277Y-68465705D01* +X133085401Y-68356728D01* +X132857105Y-68282549D01* +X132620025Y-68245000D01* +X132379975Y-68245000D01* +X132142894Y-68282549D01* +X131914598Y-68356728D01* +X131700729Y-68465701D01* +X131612995Y-68529442D01* +X132350178Y-69266624D01* +X132297358Y-69280778D01* +X132177643Y-69349896D01* +X132079896Y-69447643D01* +X132010778Y-69567358D01* +X131996624Y-69620177D01* +X131259442Y-68882995D01* +X131195701Y-68970729D01* +X131086728Y-69184598D01* +X131012549Y-69412894D01* +X130975000Y-69649974D01* +X120250500Y-69649974D01* +X120250500Y-67721153D01* +X123699500Y-67721153D01* +X123699500Y-67878846D01* +X123730261Y-68033489D01* +X123730264Y-68033501D01* +X123790602Y-68179172D01* +X123790609Y-68179185D01* +X123878210Y-68310288D01* +X123878213Y-68310292D01* +X123989707Y-68421786D01* +X123989711Y-68421789D01* +X124120814Y-68509390D01* +X124120827Y-68509397D01* +X124266498Y-68569735D01* +X124266503Y-68569737D01* +X124421153Y-68600499D01* +X124421156Y-68600500D01* +X124421158Y-68600500D01* +X124578844Y-68600500D01* +X124578845Y-68600499D01* +X124733497Y-68569737D01* +X124879179Y-68509394D01* +X124879185Y-68509390D01* +X124932751Y-68473599D01* +X124972596Y-68446974D01* +X125010289Y-68421789D01* +X125121789Y-68310289D01* +X125209394Y-68179179D01* +X125269737Y-68033497D01* +X125300500Y-67878842D01* +X125300500Y-67721158D01* +X125300500Y-67721155D01* +X125300499Y-67721153D01* +X125280734Y-67621789D01* +X125269737Y-67566503D01* +X125246452Y-67510288D01* +X125209397Y-67420827D01* +X125209390Y-67420814D01* +X125121789Y-67289711D01* +X125121786Y-67289707D01* +X125010292Y-67178213D01* +X125010288Y-67178210D01* +X124879185Y-67090609D01* +X124879172Y-67090602D01* +X124733501Y-67030264D01* +X124733489Y-67030261D01* +X124578845Y-66999500D01* +X124578842Y-66999500D01* +X124421158Y-66999500D01* +X124421155Y-66999500D01* +X124266510Y-67030261D01* +X124266498Y-67030264D01* +X124120827Y-67090602D01* +X124120814Y-67090609D01* +X123989711Y-67178210D01* +X123989707Y-67178213D01* +X123878213Y-67289707D01* +X123878210Y-67289711D01* +X123790609Y-67420814D01* +X123790602Y-67420827D01* +X123730264Y-67566498D01* +X123730261Y-67566510D01* +X123699500Y-67721153D01* +X120250500Y-67721153D01* +X120250500Y-66921153D01* +X131699500Y-66921153D01* +X131699500Y-67078846D01* +X131730261Y-67233489D01* +X131730264Y-67233501D01* +X131790602Y-67379172D01* +X131790609Y-67379185D01* +X131878210Y-67510288D01* +X131878213Y-67510292D01* +X131989707Y-67621786D01* +X131989711Y-67621789D01* +X132120814Y-67709390D01* +X132120827Y-67709397D01* +X132266498Y-67769735D01* +X132266503Y-67769737D01* +X132421153Y-67800499D01* +X132421156Y-67800500D01* +X132421158Y-67800500D01* +X132578844Y-67800500D01* +X132578845Y-67800499D01* +X132733497Y-67769737D01* +X132879179Y-67709394D01* +X133010289Y-67621789D01* +X133121789Y-67510289D01* +X133209394Y-67379179D01* +X133269737Y-67233497D01* +X133300500Y-67078842D01* +X133300500Y-66921158D01* +X133300500Y-66921155D01* +X133300499Y-66921153D01* +X133269738Y-66766510D01* +X133269737Y-66766503D01* +X133269735Y-66766498D01* +X133209397Y-66620827D01* +X133209390Y-66620814D01* +X133121789Y-66489711D01* +X133121786Y-66489707D01* +X133010292Y-66378213D01* +X133010288Y-66378210D01* +X132879185Y-66290609D01* +X132879172Y-66290602D01* +X132733501Y-66230264D01* +X132733489Y-66230261D01* +X132578845Y-66199500D01* +X132578842Y-66199500D01* +X132421158Y-66199500D01* +X132421155Y-66199500D01* +X132266510Y-66230261D01* +X132266498Y-66230264D01* +X132120827Y-66290602D01* +X132120814Y-66290609D01* +X131989711Y-66378210D01* +X131989707Y-66378213D01* +X131878213Y-66489707D01* +X131878210Y-66489711D01* +X131790609Y-66620814D01* +X131790602Y-66620827D01* +X131730264Y-66766498D01* +X131730261Y-66766510D01* +X131699500Y-66921153D01* +X120250500Y-66921153D01* +X120250500Y-64721153D01* +X123399500Y-64721153D01* +X123399500Y-64878846D01* +X123430261Y-65033489D01* +X123430264Y-65033501D01* +X123490602Y-65179172D01* +X123490609Y-65179185D01* +X123578210Y-65310288D01* +X123578213Y-65310292D01* +X123689707Y-65421786D01* +X123689711Y-65421789D01* +X123820814Y-65509390D01* +X123820827Y-65509397D01* +X123966498Y-65569735D01* +X123966503Y-65569737D01* +X124121153Y-65600499D01* +X124121156Y-65600500D01* +X124121158Y-65600500D01* +X124278844Y-65600500D01* +X124278845Y-65600499D01* +X124433497Y-65569737D01* +X124579179Y-65509394D01* +X124710289Y-65421789D01* +X124821789Y-65310289D01* +X124909394Y-65179179D01* +X124969737Y-65033497D01* +X125000500Y-64878842D01* +X125000500Y-64721158D01* +X125000500Y-64721155D01* +X125000499Y-64721153D01* +X124969737Y-64566503D01* +X124950955Y-64521158D01* +X124909397Y-64420827D01* +X124909390Y-64420814D01* +X124821789Y-64289711D01* +X124821786Y-64289707D01* +X124710292Y-64178213D01* +X124710288Y-64178210D01* +X124579185Y-64090609D01* +X124579172Y-64090602D01* +X124433501Y-64030264D01* +X124433489Y-64030261D01* +X124278845Y-63999500D01* +X124278842Y-63999500D01* +X124121158Y-63999500D01* +X124121155Y-63999500D01* +X123966510Y-64030261D01* +X123966498Y-64030264D01* +X123820827Y-64090602D01* +X123820814Y-64090609D01* +X123689711Y-64178210D01* +X123689707Y-64178213D01* +X123578213Y-64289707D01* +X123578210Y-64289711D01* +X123490609Y-64420814D01* +X123490602Y-64420827D01* +X123430264Y-64566498D01* +X123430261Y-64566510D01* +X123399500Y-64721153D01* +X120250500Y-64721153D01* +X120250500Y-62493713D01* +X121149500Y-62493713D01* +X121149500Y-62706287D01* +X121182754Y-62916243D01* +X121247738Y-63116243D01* +X121248444Y-63118414D01* +X121344951Y-63307820D01* +X121469890Y-63479786D01* +X121620213Y-63630109D01* +X121792179Y-63755048D01* +X121792181Y-63755049D01* +X121792184Y-63755051D01* +X121981588Y-63851557D01* +X122183757Y-63917246D01* +X122393713Y-63950500D01* +X122393714Y-63950500D01* +X122606286Y-63950500D01* +X122606287Y-63950500D01* +X122816243Y-63917246D01* +X123018412Y-63851557D01* +X123207816Y-63755051D01* +X123254473Y-63721153D01* +X129899500Y-63721153D01* +X129899500Y-63878846D01* +X129930261Y-64033489D01* +X129930264Y-64033501D01* +X129990602Y-64179172D01* +X129990609Y-64179185D01* +X130078210Y-64310288D01* +X130078213Y-64310292D01* +X130189707Y-64421786D01* +X130189711Y-64421789D01* +X130320814Y-64509390D01* +X130320827Y-64509397D01* +X130458683Y-64566498D01* +X130466503Y-64569737D01* +X130621153Y-64600499D01* +X130621156Y-64600500D01* +X130621158Y-64600500D01* +X130778844Y-64600500D01* +X130778845Y-64600499D01* +X130933497Y-64569737D01* +X131050790Y-64521153D01* +X134099500Y-64521153D01* +X134099500Y-64678846D01* +X134130261Y-64833489D01* +X134130264Y-64833501D01* +X134190602Y-64979172D01* +X134190609Y-64979185D01* +X134278210Y-65110288D01* +X134278213Y-65110292D01* +X134389707Y-65221786D01* +X134389711Y-65221789D01* +X134520814Y-65309390D01* +X134520827Y-65309397D01* +X134666498Y-65369735D01* +X134666503Y-65369737D01* +X134821153Y-65400499D01* +X134821156Y-65400500D01* +X134821158Y-65400500D01* +X134978844Y-65400500D01* +X134978845Y-65400499D01* +X135133497Y-65369737D01* +X135279179Y-65309394D01* +X135410289Y-65221789D01* +X135521789Y-65110289D01* +X135609394Y-64979179D01* +X135669737Y-64833497D01* +X135700500Y-64678842D01* +X135700500Y-64521158D01* +X135700500Y-64521155D01* +X135700499Y-64521153D01* +X135680734Y-64421788D01* +X135669737Y-64366503D01* +X135637929Y-64289711D01* +X135609397Y-64220827D01* +X135609390Y-64220814D01* +X135521789Y-64089711D01* +X135521786Y-64089707D01* +X135410292Y-63978213D01* +X135410288Y-63978210D01* +X135279185Y-63890609D01* +X135279172Y-63890602D01* +X135133501Y-63830264D01* +X135133489Y-63830261D01* +X134978845Y-63799500D01* +X134978842Y-63799500D01* +X134821158Y-63799500D01* +X134821155Y-63799500D01* +X134666510Y-63830261D01* +X134666498Y-63830264D01* +X134520827Y-63890602D01* +X134520814Y-63890609D01* +X134389711Y-63978210D01* +X134389707Y-63978213D01* +X134278213Y-64089707D01* +X134278210Y-64089711D01* +X134190609Y-64220814D01* +X134190602Y-64220827D01* +X134130264Y-64366498D01* +X134130261Y-64366510D01* +X134099500Y-64521153D01* +X131050790Y-64521153D01* +X131079179Y-64509394D01* +X131210289Y-64421789D01* +X131321789Y-64310289D01* +X131409394Y-64179179D01* +X131469737Y-64033497D01* +X131500500Y-63878842D01* +X131500500Y-63721158D01* +X131500500Y-63721155D01* +X131500499Y-63721153D01* +X131492272Y-63679792D01* +X131469737Y-63566503D01* +X131438080Y-63490075D01* +X131430611Y-63420606D01* +X131461886Y-63358127D01* +X131483749Y-63339521D01* +X131510289Y-63321789D01* +X131621789Y-63210289D01* +X131709394Y-63079179D01* +X131769737Y-62933497D01* +X131800500Y-62778842D01* +X131800500Y-62693713D01* +X146049500Y-62693713D01* +X146049500Y-62906286D01* +X146076917Y-63079394D01* +X146082754Y-63116243D01* +X146145001Y-63307820D01* +X146148444Y-63318414D01* +X146244951Y-63507820D01* +X146369890Y-63679786D01* +X146520213Y-63830109D01* +X146692179Y-63955048D01* +X146692181Y-63955049D01* +X146692184Y-63955051D01* +X146881588Y-64051557D01* +X147083757Y-64117246D01* +X147293713Y-64150500D01* +X147293714Y-64150500D01* +X147506286Y-64150500D01* +X147506287Y-64150500D01* +X147716243Y-64117246D01* +X147918412Y-64051557D01* +X148107816Y-63955051D01* +X148129789Y-63939086D01* +X148279786Y-63830109D01* +X148279788Y-63830106D01* +X148279792Y-63830104D01* +X148430104Y-63679792D01* +X148430106Y-63679788D01* +X148430109Y-63679786D01* +X148555048Y-63507820D01* +X148555047Y-63507820D01* +X148555051Y-63507816D01* +X148651557Y-63318412D01* +X148717246Y-63116243D01* +X148750500Y-62906287D01* +X148750500Y-62693713D01* +X148717246Y-62483757D01* +X148651557Y-62281588D01* +X148555051Y-62092184D01* +X148555049Y-62092181D01* +X148555048Y-62092179D01* +X148430109Y-61920213D01* +X148279786Y-61769890D01* +X148107820Y-61644951D01* +X147918414Y-61548444D01* +X147918413Y-61548443D01* +X147918412Y-61548443D01* +X147716243Y-61482754D01* +X147716241Y-61482753D01* +X147716240Y-61482753D01* +X147554957Y-61457208D01* +X147506287Y-61449500D01* +X147293713Y-61449500D01* +X147245042Y-61457208D01* +X147083760Y-61482753D01* +X146881585Y-61548444D01* +X146692179Y-61644951D01* +X146520213Y-61769890D01* +X146369890Y-61920213D01* +X146244951Y-62092179D01* +X146148444Y-62281585D01* +X146082753Y-62483760D01* +X146049500Y-62693713D01* +X131800500Y-62693713D01* +X131800500Y-62621158D01* +X131800500Y-62621155D01* +X131800499Y-62621153D01* +X131775149Y-62493713D01* +X131769737Y-62466503D01* +X131750796Y-62420775D01* +X131709397Y-62320827D01* +X131709390Y-62320814D01* +X131621789Y-62189711D01* +X131621786Y-62189707D01* +X131510292Y-62078213D01* +X131510288Y-62078210D01* +X131379185Y-61990609D01* +X131379172Y-61990602D01* +X131233501Y-61930264D01* +X131233489Y-61930261D01* +X131078845Y-61899500D01* +X131078842Y-61899500D01* +X130921158Y-61899500D01* +X130921155Y-61899500D01* +X130766510Y-61930261D01* +X130766498Y-61930264D01* +X130620827Y-61990602D01* +X130620814Y-61990609D01* +X130489711Y-62078210D01* +X130489707Y-62078213D01* +X130378213Y-62189707D01* +X130378210Y-62189711D01* +X130290609Y-62320814D01* +X130290602Y-62320827D01* +X130230264Y-62466498D01* +X130230261Y-62466510D01* +X130199500Y-62621153D01* +X130199500Y-62778846D01* +X130230261Y-62933489D01* +X130230264Y-62933501D01* +X130261919Y-63009924D01* +X130269388Y-63079394D01* +X130238112Y-63141873D01* +X130216252Y-63160476D01* +X130189709Y-63178212D01* +X130189704Y-63178217D01* +X130078213Y-63289707D01* +X130078210Y-63289711D01* +X129990609Y-63420814D01* +X129990602Y-63420827D01* +X129930264Y-63566498D01* +X129930261Y-63566510D01* +X129899500Y-63721153D01* +X123254473Y-63721153D01* +X123311402Y-63679792D01* +X123379786Y-63630109D01* +X123379788Y-63630106D01* +X123379792Y-63630104D01* +X123530104Y-63479792D01* +X123530106Y-63479788D01* +X123530109Y-63479786D01* +X123655048Y-63307820D01* +X123655047Y-63307820D01* +X123655051Y-63307816D01* +X123751557Y-63118412D01* +X123817246Y-62916243D01* +X123850500Y-62706287D01* +X123850500Y-62493713D01* +X123817246Y-62283757D01* +X123751557Y-62081588D01* +X123655051Y-61892184D01* +X123638203Y-61868995D01* +X132174499Y-61868995D01* +X132201418Y-62004322D01* +X132201421Y-62004332D01* +X132254221Y-62131804D01* +X132254228Y-62131817D01* +X132330885Y-62246541D01* +X132330888Y-62246545D01* +X132428454Y-62344111D01* +X132428458Y-62344114D01* +X132543182Y-62420771D01* +X132543195Y-62420778D01* +X132653603Y-62466510D01* +X132670672Y-62473580D01* +X132670676Y-62473580D01* +X132670677Y-62473581D01* +X132806004Y-62500500D01* +X132806007Y-62500500D01* +X132943995Y-62500500D01* +X133035041Y-62482389D01* +X133079328Y-62473580D01* +X133206811Y-62420775D01* +X133321542Y-62344114D01* +X133419114Y-62246542D01* +X133495775Y-62131811D01* +X133548580Y-62004328D01* +X133575500Y-61868995D01* +X136424499Y-61868995D01* +X136451418Y-62004322D01* +X136451421Y-62004332D01* +X136504221Y-62131804D01* +X136504228Y-62131817D01* +X136580885Y-62246541D01* +X136580888Y-62246545D01* +X136678454Y-62344111D01* +X136678458Y-62344114D01* +X136793182Y-62420771D01* +X136793195Y-62420778D01* +X136903603Y-62466510D01* +X136920672Y-62473580D01* +X136920676Y-62473580D01* +X136920677Y-62473581D01* +X137056004Y-62500500D01* +X137056007Y-62500500D01* +X137193995Y-62500500D01* +X137285041Y-62482389D01* +X137329328Y-62473580D01* +X137456811Y-62420775D01* +X137571542Y-62344114D01* +X137669114Y-62246542D01* +X137745775Y-62131811D01* +X137798580Y-62004328D01* +X137825500Y-61868993D01* +X137825500Y-61731007D01* +X137825500Y-61731004D01* +X137798581Y-61595677D01* +X137798580Y-61595676D01* +X137798580Y-61595672D01* +X137751808Y-61482753D01* +X137745778Y-61468195D01* +X137745771Y-61468182D01* +X137669114Y-61353458D01* +X137669111Y-61353454D01* +X137571545Y-61255888D01* +X137571541Y-61255885D01* +X137456817Y-61179228D01* +X137456804Y-61179221D01* +X137329332Y-61126421D01* +X137329322Y-61126418D01* +X137193995Y-61099500D01* +X137193993Y-61099500D01* +X137056007Y-61099500D01* +X137056005Y-61099500D01* +X136920677Y-61126418D01* +X136920667Y-61126421D01* +X136793195Y-61179221D01* +X136793182Y-61179228D01* +X136678458Y-61255885D01* +X136678454Y-61255888D01* +X136580888Y-61353454D01* +X136580885Y-61353458D01* +X136504228Y-61468182D01* +X136504221Y-61468195D01* +X136451421Y-61595667D01* +X136451418Y-61595677D01* +X136424500Y-61731004D01* +X136424500Y-61731007D01* +X136424500Y-61868993D01* +X136424500Y-61868995D01* +X136424499Y-61868995D01* +X133575500Y-61868995D01* +X133575500Y-61868993D01* +X133575500Y-61731007D01* +X133575500Y-61731004D01* +X133548581Y-61595677D01* +X133548580Y-61595676D01* +X133548580Y-61595672D01* +X133501808Y-61482753D01* +X133495778Y-61468195D01* +X133495771Y-61468182D01* +X133419114Y-61353458D01* +X133419111Y-61353454D01* +X133321545Y-61255888D01* +X133321541Y-61255885D01* +X133206817Y-61179228D01* +X133206804Y-61179221D01* +X133079332Y-61126421D01* +X133079322Y-61126418D01* +X132943995Y-61099500D01* +X132943993Y-61099500D01* +X132806007Y-61099500D01* +X132806005Y-61099500D01* +X132670677Y-61126418D01* +X132670667Y-61126421D01* +X132543195Y-61179221D01* +X132543182Y-61179228D01* +X132428458Y-61255885D01* +X132428454Y-61255888D01* +X132330888Y-61353454D01* +X132330885Y-61353458D01* +X132254228Y-61468182D01* +X132254221Y-61468195D01* +X132201421Y-61595667D01* +X132201418Y-61595677D01* +X132174500Y-61731004D01* +X132174500Y-61731007D01* +X132174500Y-61868993D01* +X132174500Y-61868995D01* +X132174499Y-61868995D01* +X123638203Y-61868995D01* +X123530104Y-61720208D01* +X123379792Y-61569896D01* +X123379786Y-61569890D01* +X123207820Y-61444951D01* +X123018414Y-61348444D01* +X123018413Y-61348443D01* +X123018412Y-61348443D01* +X122816243Y-61282754D01* +X122816241Y-61282753D01* +X122816240Y-61282753D01* +X122646600Y-61255885D01* +X122606287Y-61249500D01* +X122393713Y-61249500D01* +X122353400Y-61255885D01* +X122183760Y-61282753D01* +X121981585Y-61348444D01* +X121792179Y-61444951D01* +X121620213Y-61569890D01* +X121469890Y-61720213D01* +X121344951Y-61892179D01* +X121248444Y-62081585D01* +X121182753Y-62283760D01* +X121152689Y-62473578D01* +X121149500Y-62493713D01* +X120250500Y-62493713D01* +X120250500Y-60374500D01* +X120270185Y-60307461D01* +X120322989Y-60261706D01* +X120374500Y-60250500D01* +X149625500Y-60250500D01* +X149692539Y-60270185D01* G37* %TD.AperFunction*% %TD*% diff --git a/PCB/v2.x/production/gerbers/snips_controller-In2_Cu.gbr b/PCB/v2.x/production/gerbers/snips_controller-In2_Cu.gbr index 09deede..07730b1 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-In2_Cu.gbr +++ b/PCB/v2.x/production/gerbers/snips_controller-In2_Cu.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:02-07:00*% +%TF.CreationDate,2026-10-31T14:04:15-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Copper,L3,Inr*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:02* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:15* %MOMM*% %LPD*% G01* @@ -30,28 +30,28 @@ G04 Aperture macros list* 20,1,$1+$1,$8,$9,$2,$3,0*% G04 Aperture macros list end* %TA.AperFunction,ComponentPad*% -%ADD10C,0.300000*% +%ADD10O,1.000000X2.100000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD11O,1.000000X2.100000*% +%ADD11O,1.000000X1.600000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD12O,1.000000X1.600000*% +%ADD12C,2.550000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD13C,2.550000*% +%ADD13C,2.050000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD14C,2.050000*% +%ADD14C,2.250000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD15C,2.250000*% +%ADD15RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD16RoundRect,0.250000X-0.350000X-0.625000X0.350000X-0.625000X0.350000X0.625000X-0.350000X0.625000X0*% +%ADD16O,1.200000X1.750000*% %TD*% %TA.AperFunction,ComponentPad*% -%ADD17O,1.200000X1.750000*% +%ADD17C,0.300000*% %TD*% %TA.AperFunction,ViaPad*% %ADD18C,0.600000*% @@ -59,29 +59,23 @@ G04 Aperture macros list end* G04 APERTURE END LIST* D10* %TO.N,GND*% -%TO.C,U_CHG1*% -X129750000Y-118815000D03* -X129750000Y-117815000D03* -%TD*% -D11* -%TO.N,GND*% %TO.C,J_USB1*% X132680000Y-124020000D03* -D12* -X132680000Y-128200000D03* D11* +X132680000Y-128200000D03* +D10* X141320000Y-124020000D03* -D12* +D11* X141320000Y-128200000D03* %TD*% -D13* +D12* %TO.N,*% %TO.C,J_STICK1*% X128675000Y-73500000D03* X128675000Y-83500000D03* X141325000Y-73500000D03* X141325000Y-83500000D03* -D14* +D13* %TO.N,GND*% X137500000Y-69770000D03* X143730000Y-81000000D03* @@ -89,10 +83,10 @@ X143730000Y-81000000D03* X135000000Y-69770000D03* %TO.N,/MCU_Core/STICK_Y*% X143730000Y-78500000D03* -%TO.N,/MCU_Core/3V3_RF*% +%TO.N,3V3*% X132500000Y-69770000D03* X143730000Y-76000000D03* -D15* +D14* %TO.N,/MCU_Core/BTN_STICK*% X131750000Y-84250000D03* %TO.N,N/C*% @@ -102,387 +96,224 @@ X131750000Y-88750000D03* %TO.N,N/C*% X138250000Y-88750000D03* %TD*% -D16* +D15* %TO.N,VBAT*% %TO.C,BT1*% X145200000Y-123100000D03* -D17* +D16* %TO.N,GND*% X147200000Y-123100000D03* %TD*% +D17* +%TO.N,GND*% +%TO.C,U_CHG1*% +X128750000Y-95750000D03* +X128750000Y-96750000D03* +%TD*% D18* -%TO.N,VSYS*% -X131134999Y-72039999D03* -X133551500Y-90667500D03* -X131197200Y-105109200D03* -X135775300Y-108336200D03* -X127561250Y-90824999D03* +%TO.N,3V3*% +X127761250Y-93014999D03* +X145311599Y-107614004D03* +X136012023Y-99792121D03* +X131100000Y-101100000D03* +X132248535Y-126920005D03* +X127200000Y-127762500D03* +X124950000Y-104123528D03* +X134200000Y-106400000D03* +X125080000Y-124896016D03* +X123900000Y-98100000D03* +X141068110Y-104176936D03* +X130620864Y-129450000D03* +X129000000Y-64600000D03* +X126320000Y-106400000D03* +X145500000Y-117780000D03* +X138500000Y-93250000D03* +X137400000Y-100200000D03* %TO.N,GND*% -X144000000Y-94500000D03* -X131800000Y-124350000D03* -X130449999Y-67550000D03* -X143750000Y-70550000D03* -X123950000Y-83200000D03* -X121300000Y-107150000D03* -X142800000Y-95850000D03* -X139100000Y-103700000D03* -X122350000Y-105150000D03* -X131800000Y-96500000D03* -X136300000Y-95300000D03* -X121750000Y-119315000D03* -X122600000Y-125750000D03* -X128750000Y-124300000D03* -X123150000Y-85600000D03* -X123050000Y-95850000D03* -X140500000Y-108600000D03* -X128750000Y-103050000D03* -X122600000Y-124650000D03* -X146500000Y-67450000D03* -X135250000Y-106825000D03* -X140800000Y-122150000D03* -X142850000Y-95000000D03* -X136250000Y-117315000D03* -X134600000Y-103700000D03* -X130500000Y-92300000D03* -X129870634Y-119615000D03* -X131450000Y-117565000D03* -X145300000Y-75100000D03* -X136400000Y-100400000D03* -X140000000Y-69400000D03* -X134700000Y-63950000D03* -X135450000Y-103800000D03* -X137850000Y-104150000D03* -X133000000Y-119265000D03* -X129000000Y-96550000D03* -X148500000Y-83050000D03* +X140600000Y-118700000D03* +X126900000Y-123500000D03* +X128300000Y-97700000D03* +X128700000Y-100300000D03* +X139600000Y-114100000D03* +X130850000Y-97425000D03* +X130700000Y-63800000D03* +X139100000Y-70700000D03* +X132500000Y-67000000D03* +X145400000Y-88100000D03* +X137500000Y-97750000D03* +X135250000Y-97250000D03* +X124200000Y-71800000D03* +X134900000Y-64600000D03* +X147050000Y-96950000D03* +X146248528Y-83299999D03* +X124200000Y-64800000D03* +X145600000Y-73000000D03* +X124750000Y-96250000D03* +X131300000Y-117800000D03* +X130800000Y-106700000D03* +X122600000Y-104000000D03* +X142000000Y-114200000D03* +X124100000Y-83700000D03* +X140400000Y-100300000D03* +X121800000Y-96700000D03* +X137799998Y-103000000D03* +X135250000Y-95750000D03* X136285000Y-75940000D03* -X144550000Y-69350000D03* -X143300000Y-102350000D03* -X143200000Y-90650000D03* -X132150000Y-104150000D03* -X130449999Y-103700000D03* -X141700000Y-70000000D03* -X137400000Y-125800000D03* -X123950000Y-73200000D03* -X137450000Y-114300000D03* -X129770634Y-116815000D03* -X131900000Y-100400000D03* -X144950000Y-110700000D03* -X148500000Y-73050000D03* -X143300000Y-106450000D03* -X137050000Y-92150000D03* +X131800000Y-100500000D03* +X128349799Y-95084604D03* +X132000000Y-95300000D03* X131785000Y-73440000D03* -X142800000Y-103050000D03* -X136050000Y-101250000D03* -X141950000Y-79700000D03* -X129800000Y-64050000D03* -X139850000Y-87250000D03* -X145350000Y-93100000D03* -X130950000Y-107800000D03* -X142800000Y-126600000D03* -X146350000Y-66599999D03* -X145450000Y-95800000D03* -X134550000Y-101250000D03* -X147450000Y-106450000D03* -X123050000Y-103050000D03* -X136250000Y-118815000D03* -X147450000Y-102350000D03* -X142900000Y-67400000D03* -X145400000Y-103050000D03* -X123000000Y-104550000D03* -X133199999Y-122150000D03* -X130400000Y-126300000D03* -X125750000Y-118315000D03* -%TO.N,/Buttons_Direct/BTN_MACRO4*% -X129800000Y-100700000D03* -%TO.N,VBUS*% -X125770000Y-125525300D03* -X134650000Y-121702500D03* -X139450000Y-121868900D03* -X141321300Y-92762500D03* -X141703000Y-89578400D03* -X149218700Y-96601800D03* -%TO.N,3V3*% -X131950000Y-112300000D03* -X127300000Y-121550001D03* -X123900000Y-113658400D03* -X146120300Y-98555000D03* -X124549200Y-107406100D03* -X123860000Y-116915000D03* -%TO.N,/Buttons_Direct/BTN_MACRO2*% -X131797000Y-95119100D03* +X122500000Y-125200000D03* +%TO.N,/MCU_Core/MCU_BOOT*% +X139900000Y-106400000D03* +X144900000Y-108300000D03* +%TO.N,/Hall_Trigger/TRIG_ADC*% +X130070634Y-92600000D03* %TO.N,/Buttons_Direct/BTN_THR_UP*% -X124754600Y-83434100D03* -X132620800Y-86688200D03* +X121873930Y-107063387D03* +X130300000Y-116600000D03* %TO.N,/Buttons_Direct/BTN_MACRO6*% -X139209300Y-100184300D03* -%TO.N,/Buttons_Direct/BTN_MACRO3*% -X139789800Y-98443100D03* +X141300000Y-106600000D03* +X142600000Y-102400000D03* %TO.N,/Buttons_Direct/BTN_MACRO1*% -X129065000Y-94095500D03* -%TO.N,VBAT*% -X133810600Y-118937400D03* -%TO.N,/MCU_Core/STAT2*% -X130387500Y-96500000D03* -%TO.N,/MCU_Core/STAT1*% -X123374265Y-117590735D03* +X128200000Y-105450002D03* +X130400000Y-109900000D03* %TO.N,/Accelerometer/I2C_SDA*% -X132254800Y-65652100D03* -X124959600Y-104749000D03* +X124200000Y-111600000D03* +X124600000Y-109800000D03* +X121874741Y-124680758D03* %TO.N,/Accelerometer/I2C_SCL*% -X121327800Y-96462500D03* -X126003900Y-70995100D03* -X126735300Y-100400000D03* -%TO.N,/Buttons_Direct/BTN_VOL_DN*% -X145804700Y-84769200D03* -%TO.N,/USB_C/USB_CC1*% -X135750000Y-121500900D03* -%TO.N,/MCU_Core/USB_DP*% -X148072200Y-111842500D03* -X139484600Y-96501700D03* -%TO.N,/MCU_Core/USB_DM*% -X137901700Y-95241600D03* -%TO.N,/USB_C/USB_CC2*% -X138750000Y-126065000D03* -%TO.N,/MCU_Core/STICK_X*% -X126670100Y-93676600D03* -%TO.N,/MCU_Core/STICK_Y*% -X130207300Y-95609600D03* -%TO.N,/MCU_Core/3V3_RF*% -X142999700Y-92385900D03* +X125800000Y-109700000D03* +X122700000Y-114100000D03* +X121100000Y-124880210D03* +%TO.N,/XBee/XBEE_SLEEP_RQ*% +X138900000Y-106200000D03* +%TO.N,/Buttons_Direct/BTN_MACRO5*% +X133300000Y-100800000D03* +X133100000Y-107000000D03* +X136161765Y-101138235D03* +%TO.N,/MCU_Core/STAT2*% +X130824265Y-108075735D03* +%TO.N,/MCU_Core/STAT1*% +X130800000Y-108900000D03* +X127500000Y-99000000D03* +X126150000Y-97470100D03* %TO.N,/MCU_Core/BTN_STICK*% -X134709100Y-92787200D03* +X130500000Y-110800000D03* +X126600000Y-100400000D03* %TO.N,/MCU_Core/PWR_BTN_SENSE*% -X145452900Y-98045000D03* -X120688600Y-97070100D03* +X120600000Y-125765642D03* +X130500000Y-114200000D03* +X124000000Y-119600000D03* +%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% +X131000000Y-62700000D03* +X122300000Y-87800000D03* +X131700000Y-115100000D03* +X124500000Y-67800000D03* +X121893900Y-106234827D03* +%TO.N,/XBee/XBEE_CTS*% +X127800000Y-117800000D03* %TO.N,/MCU_Core/RGB_DIN*% -X129216700Y-123115100D03* -%TO.N,/Buttons_Direct/BTN_THR_DN*% -X123557800Y-90439600D03* -%TO.N,/Buttons_Direct/BTN_VOL_UP*% -X135734500Y-92661400D03* -%TO.N,/Power_Buck/PWR_EN*% -X145850800Y-107623700D03* -X145980700Y-85815700D03* -X141116700Y-110981600D03* -%TO.N,/Buttons_Direct/BTN_MACRO5*% -X136150000Y-104250000D03* -%TO.N,/Hall_Trigger/TRIG_ADC*% -X127525700Y-92504700D03* -X129861700Y-101982200D03* +X126002198Y-123340339D03* +X130400000Y-117400000D03* +%TO.N,/XBee/XBEE_DIN*% +X130179998Y-120689999D03* +%TO.N,/XBee/XBEE_DOUT*% +X131615136Y-118535318D03* %TO.N,ACCEL_INT1*% -X129871400Y-99693700D03* -X139636800Y-97508700D03* -X147014800Y-76170200D03* -%TO.N,/Buttons_Direct/BTN_TRIG_DIG*% -X134775000Y-95096400D03* -X135000000Y-61269100D03* -X134105300Y-87305100D03* +X139400000Y-116900000D03* +%TO.N,/Buttons_Direct/BTN_VOL_UP*% +X147034358Y-98156239D03* +X133000000Y-118200000D03* +%TO.N,/XBee/XBEE_RTS*% +X133900000Y-118200000D03* +%TO.N,/Buttons_Direct/BTN_VOL_DN*% +X147700000Y-98600000D03* +X134700000Y-117700000D03* +%TO.N,/XBee/XBEE_ON_SLEEP*% +X135600000Y-118300000D03* +%TO.N,/XBee/XBEE_RESET*% +X136500000Y-118300000D03* %TO.N,/MCU_Core/PWR_HOLD*% +X140950000Y-90700000D03* X138485000Y-72539999D03* -X129625000Y-98237500D03* -%TO.N,/Hall_Trigger/TRIG_ANALOG*% -X127260700Y-66852300D03* -X126692500Y-80628700D03* +X142000000Y-107300000D03* +%TO.N,VBUS*% +X123750000Y-95250000D03* +X137000000Y-124900000D03* +X122300000Y-102800000D03* +%TO.N,/USB_C/USB_CC1*% +X129200000Y-123700000D03* +%TO.N,/USB_C/USB_CC2*% +X142300000Y-124900000D03* +%TO.N,VSYS*% +X129700000Y-93350000D03* +X142100000Y-79300000D03* +X144800000Y-90650000D03* +X144600000Y-86300000D03* +%TO.N,VBAT*% +X135900000Y-99000000D03* +X147300000Y-109300000D03* +%TO.N,/Power_Buck/BUCK_FB*% +X139885887Y-98225129D03* +X139500000Y-94850000D03* %TD*% %TA.AperFunction,Conductor*% %TO.N,GND*% G36* -X134825667Y-60270185D02* +X149692539Y-60270185D02* G01* -X134871422Y-60322989D01* -X134881366Y-60392147D01* -X134852341Y-60455703D01* -X134793563Y-60493477D01* -X134782819Y-60496117D01* -X134766510Y-60499361D01* -X134766498Y-60499364D01* -X134620827Y-60559702D01* -X134620814Y-60559709D01* -X134489711Y-60647310D01* -X134489707Y-60647313D01* -X134378213Y-60758807D01* -X134378210Y-60758811D01* -X134290609Y-60889914D01* -X134290602Y-60889927D01* -X134230264Y-61035598D01* -X134230261Y-61035610D01* -X134199500Y-61190253D01* -X134199500Y-61347946D01* -X134230261Y-61502589D01* -X134230264Y-61502601D01* -X134290602Y-61648272D01* -X134290609Y-61648285D01* -X134378210Y-61779388D01* -X134378213Y-61779392D01* -X134489707Y-61890886D01* -X134489711Y-61890889D01* -X134620814Y-61978490D01* -X134620827Y-61978497D01* -X134766498Y-62038835D01* -X134766503Y-62038837D01* -X134921153Y-62069599D01* -X134921156Y-62069600D01* -X134921158Y-62069600D01* -X135078844Y-62069600D01* -X135078845Y-62069599D01* -X135233497Y-62038837D01* -X135379179Y-61978494D01* -X135510289Y-61890889D01* -X135532183Y-61868995D01* -X136424499Y-61868995D01* -X136451418Y-62004322D01* -X136451421Y-62004332D01* -X136504221Y-62131804D01* -X136504228Y-62131817D01* -X136580885Y-62246541D01* -X136580888Y-62246545D01* -X136678454Y-62344111D01* -X136678458Y-62344114D01* -X136793182Y-62420771D01* -X136793195Y-62420778D01* -X136920667Y-62473578D01* -X136920672Y-62473580D01* -X136920676Y-62473580D01* -X136920677Y-62473581D01* -X137056004Y-62500500D01* -X137056007Y-62500500D01* -X137193995Y-62500500D01* -X137285041Y-62482389D01* -X137329328Y-62473580D01* -X137456811Y-62420775D01* -X137571542Y-62344114D01* -X137669114Y-62246542D01* -X137745775Y-62131811D01* -X137798580Y-62004328D01* -X137825500Y-61868993D01* -X137825500Y-61731007D01* -X137825500Y-61731004D01* -X137798581Y-61595677D01* -X137798580Y-61595676D01* -X137798580Y-61595672D01* -X137760029Y-61502601D01* -X137745778Y-61468195D01* -X137745771Y-61468182D01* -X137669114Y-61353458D01* -X137669111Y-61353454D01* -X137571545Y-61255888D01* -X137571541Y-61255885D01* -X137456817Y-61179228D01* -X137456804Y-61179221D01* -X137329332Y-61126421D01* -X137329322Y-61126418D01* -X137193995Y-61099500D01* -X137193993Y-61099500D01* -X137056007Y-61099500D01* -X137056005Y-61099500D01* -X136920677Y-61126418D01* -X136920667Y-61126421D01* -X136793195Y-61179221D01* -X136793182Y-61179228D01* -X136678458Y-61255885D01* -X136678454Y-61255888D01* -X136580888Y-61353454D01* -X136580885Y-61353458D01* -X136504228Y-61468182D01* -X136504221Y-61468195D01* -X136451421Y-61595667D01* -X136451418Y-61595677D01* -X136424500Y-61731004D01* -X136424500Y-61731007D01* -X136424500Y-61868993D01* -X136424500Y-61868995D01* -X136424499Y-61868995D01* -X135532183Y-61868995D01* -X135621789Y-61779389D01* -X135661404Y-61720100D01* -X135704217Y-61656028D01* -X135704218Y-61656026D01* -X135706119Y-61653179D01* -X135709394Y-61648279D01* -X135710773Y-61644951D01* -X135741861Y-61569896D01* -X135769737Y-61502597D01* -X135800500Y-61347942D01* -X135800500Y-61190258D01* -X135800500Y-61190255D01* -X135800499Y-61190253D01* -X135769738Y-61035610D01* -X135769737Y-61035603D01* -X135769735Y-61035598D01* -X135709397Y-60889927D01* -X135709390Y-60889914D01* -X135621789Y-60758811D01* -X135621786Y-60758807D01* -X135510292Y-60647313D01* -X135510288Y-60647310D01* -X135379185Y-60559709D01* -X135379172Y-60559702D01* -X135233501Y-60499364D01* -X135233489Y-60499361D01* -X135217181Y-60496117D01* -X135155270Y-60463732D01* -X135120696Y-60403016D01* -X135124435Y-60333247D01* -X135165302Y-60276575D01* -X135230320Y-60250994D01* -X135241372Y-60250500D01* -X149625500Y-60250500D01* -X149692539Y-60270185D01* X149738294Y-60322989D01* X149749500Y-60374500D01* -X149749500Y-95769630D01* -X149729815Y-95836669D01* -X149677011Y-95882424D01* -X149607853Y-95892368D01* -X149578048Y-95884191D01* -X149452201Y-95832064D01* -X149452189Y-95832061D01* -X149297545Y-95801300D01* -X149297542Y-95801300D01* -X149139858Y-95801300D01* -X149139855Y-95801300D01* -X148985210Y-95832061D01* -X148985198Y-95832064D01* -X148839527Y-95892402D01* -X148839514Y-95892409D01* -X148708411Y-95980010D01* -X148708407Y-95980013D01* -X148596913Y-96091507D01* -X148596910Y-96091511D01* -X148509309Y-96222614D01* -X148509302Y-96222627D01* -X148448964Y-96368298D01* -X148448961Y-96368310D01* -X148418200Y-96522953D01* -X148418200Y-96680646D01* -X148448961Y-96835289D01* -X148448964Y-96835301D01* -X148509302Y-96980972D01* -X148509309Y-96980985D01* -X148596910Y-97112088D01* -X148596913Y-97112092D01* -X148708407Y-97223586D01* -X148708411Y-97223589D01* -X148839514Y-97311190D01* -X148839527Y-97311197D01* -X148985198Y-97371535D01* -X148985203Y-97371537D01* -X149139853Y-97402299D01* -X149139856Y-97402300D01* -X149139858Y-97402300D01* -X149297544Y-97402300D01* -X149297545Y-97402299D01* -X149452197Y-97371537D01* -X149578049Y-97319407D01* -X149647517Y-97311939D01* -X149709996Y-97343214D01* -X149745648Y-97403303D01* -X149749500Y-97433969D01* X149749500Y-129625500D01* X149729815Y-129692539D01* X149677011Y-129738294D01* X149625500Y-129749500D01* +X131528567Y-129749500D01* +X131461528Y-129729815D01* +X131415773Y-129677011D01* +X131405829Y-129607853D01* +X131406950Y-129601309D01* +X131421363Y-129528846D01* +X131421364Y-129528844D01* +X131421364Y-129371155D01* +X131421363Y-129371153D01* +X131402585Y-129276751D01* +X131390601Y-129216503D01* +X131357863Y-129137466D01* +X131330261Y-129070827D01* +X131330254Y-129070814D01* +X131242653Y-128939711D01* +X131242650Y-128939707D01* +X131131156Y-128828213D01* +X131131152Y-128828210D01* +X131000049Y-128740609D01* +X131000036Y-128740602D01* +X130854365Y-128680264D01* +X130854353Y-128680261D01* +X130699709Y-128649500D01* +X130699706Y-128649500D01* +X130542022Y-128649500D01* +X130542019Y-128649500D01* +X130387374Y-128680261D01* +X130387362Y-128680264D01* +X130241691Y-128740602D01* +X130241678Y-128740609D01* +X130110575Y-128828210D01* +X130110571Y-128828213D01* +X129999077Y-128939707D01* +X129999074Y-128939711D01* +X129911473Y-129070814D01* +X129911466Y-129070827D01* +X129851128Y-129216498D01* +X129851125Y-129216510D01* +X129820364Y-129371153D01* +X129820364Y-129528846D01* +X129834778Y-129601309D01* +X129828551Y-129670900D01* +X129785688Y-129726078D01* +X129719798Y-129749322D01* +X129713161Y-129749500D01* X120374500Y-129749500D01* X120307461Y-129729815D01* X120261706Y-129677011D01* @@ -537,10 +368,153 @@ X125745775Y-128231811D01* X125798580Y-128104328D01* X125825500Y-127968993D01* X125825500Y-127831007D01* -X125825499Y-127831004D01* -X125823233Y-127819610D01* -X125823233Y-127819608D01* -X125819632Y-127801504D01* +X125825500Y-127831004D01* +X125825499Y-127831002D01* +X125799791Y-127701757D01* +X125798581Y-127695677D01* +X125798580Y-127695676D01* +X125798580Y-127695672D01* +X125793604Y-127683658D01* +X125793602Y-127683653D01* +X126399500Y-127683653D01* +X126399500Y-127841346D01* +X126430261Y-127995989D01* +X126430264Y-127996001D01* +X126490602Y-128141672D01* +X126490609Y-128141685D01* +X126578210Y-128272788D01* +X126578213Y-128272792D01* +X126689707Y-128384286D01* +X126689711Y-128384289D01* +X126820814Y-128471890D01* +X126820827Y-128471897D01* +X126938821Y-128520771D01* +X126966503Y-128532237D01* +X127121153Y-128562999D01* +X127121156Y-128563000D01* +X127121158Y-128563000D01* +X127278844Y-128563000D01* +X127278845Y-128562999D01* +X127433497Y-128532237D01* +X127579179Y-128471894D01* +X127710289Y-128384289D01* +X127744078Y-128350500D01* +X127783622Y-128310957D01* +X127821786Y-128272792D01* +X127821789Y-128272789D01* +X127909394Y-128141679D01* +X127969737Y-127995997D01* +X128000500Y-127841342D01* +X128000500Y-127683658D01* +X128000500Y-127683655D01* +X128000499Y-127683653D01* +X127977533Y-127568195D01* +X127969737Y-127529003D01* +X127953381Y-127489515D01* +X127909397Y-127383327D01* +X127909390Y-127383314D01* +X127821789Y-127252211D01* +X127821786Y-127252207D01* +X127710292Y-127140713D01* +X127710288Y-127140710D01* +X127579185Y-127053109D01* +X127579172Y-127053102D01* +X127433501Y-126992764D01* +X127433489Y-126992761D01* +X127278845Y-126962000D01* +X127278842Y-126962000D01* +X127121158Y-126962000D01* +X127121155Y-126962000D01* +X126966510Y-126992761D01* +X126966498Y-126992764D01* +X126820827Y-127053102D01* +X126820814Y-127053109D01* +X126689711Y-127140710D01* +X126689707Y-127140713D01* +X126578213Y-127252207D01* +X126578210Y-127252211D01* +X126490609Y-127383314D01* +X126490602Y-127383327D01* +X126430264Y-127528998D01* +X126430261Y-127529010D01* +X126399500Y-127683653D01* +X125793602Y-127683653D01* +X125745778Y-127568195D01* +X125745771Y-127568182D01* +X125669114Y-127453458D01* +X125669111Y-127453454D01* +X125571545Y-127355888D01* +X125571541Y-127355885D01* +X125456817Y-127279228D01* +X125456804Y-127279221D01* +X125329332Y-127226421D01* +X125329322Y-127226418D01* +X125193995Y-127199500D01* +X125193993Y-127199500D01* +X125056007Y-127199500D01* +X125056005Y-127199500D01* +X124920677Y-127226418D01* +X124920667Y-127226421D01* +X124793195Y-127279221D01* +X124793182Y-127279228D01* +X124678458Y-127355885D01* +X124678454Y-127355888D01* +X124580888Y-127453454D01* +X124580885Y-127453458D01* +X124504228Y-127568182D01* +X124504221Y-127568195D01* +X124451421Y-127695667D01* +X124451418Y-127695677D01* +X124424500Y-127831004D01* +X124424500Y-127831007D01* +X124424500Y-127968993D01* +X124424500Y-127968995D01* +X124424499Y-127968995D01* +X121575500Y-127968995D01* +X121575500Y-127968993D01* +X121575500Y-127831007D01* +X121575500Y-127831004D01* +X121548581Y-127695677D01* +X121548580Y-127695676D01* +X121548580Y-127695672D01* +X121543604Y-127683658D01* +X121495778Y-127568195D01* +X121495771Y-127568182D01* +X121419114Y-127453458D01* +X121419111Y-127453454D01* +X121321545Y-127355888D01* +X121321541Y-127355885D01* +X121206817Y-127279228D01* +X121206804Y-127279221D01* +X121079332Y-127226421D01* +X121079322Y-127226418D01* +X120943995Y-127199500D01* +X120943993Y-127199500D01* +X120806007Y-127199500D01* +X120806005Y-127199500D01* +X120670677Y-127226418D01* +X120670667Y-127226421D01* +X120543195Y-127279221D01* +X120543182Y-127279228D01* +X120443391Y-127345907D01* +X120376713Y-127366785D01* +X120309333Y-127348300D01* +X120262643Y-127296321D01* +X120250500Y-127242805D01* +X120250500Y-126841158D01* +X131448035Y-126841158D01* +X131448035Y-126998851D01* +X131478796Y-127153494D01* +X131478799Y-127153506D01* +X131539137Y-127299177D01* +X131539144Y-127299190D01* +X131626744Y-127430292D01* +X131626745Y-127430293D01* +X131626746Y-127430294D01* +X131685969Y-127489517D01* +X131719453Y-127550838D01* +X131717422Y-127601900D01* +X131719617Y-127602337D01* X131680000Y-127801504D01* X131680000Y-127950000D01* X132380000Y-127950000D01* @@ -686,107 +660,11 @@ X133566192Y-127426328D01* X133566185Y-127426315D01* X133456751Y-127262537D01* X133456748Y-127262533D01* -X133317466Y-127123251D01* -X133317462Y-127123248D01* -X133153684Y-127013814D01* -X133153671Y-127013807D01* -X132971691Y-126938429D01* -X132971683Y-126938427D01* -X132930000Y-126930135D01* -X132930000Y-127733011D01* -X132920060Y-127715795D01* -X132864205Y-127659940D01* -X132795796Y-127620444D01* -X132719496Y-127600000D01* -X132640504Y-127600000D01* -X132564204Y-127620444D01* -X132495795Y-127659940D01* -X132439940Y-127715795D01* -X132430000Y-127733011D01* -X132430000Y-126930136D01* -X132429999Y-126930135D01* -X132388316Y-126938427D01* -X132388308Y-126938429D01* -X132206328Y-127013807D01* -X132206315Y-127013814D01* -X132042537Y-127123248D01* -X132042533Y-127123251D01* -X131903251Y-127262533D01* -X131903248Y-127262537D01* -X131793814Y-127426315D01* -X131793807Y-127426328D01* -X131718430Y-127608306D01* -X131718427Y-127608318D01* -X131680000Y-127801504D01* -X125819632Y-127801504D01* -X125810510Y-127755650D01* -X125798580Y-127695672D01* -X125798578Y-127695667D01* -X125745778Y-127568195D01* -X125745771Y-127568182D01* -X125669114Y-127453458D01* -X125669111Y-127453454D01* -X125571545Y-127355888D01* -X125571541Y-127355885D01* -X125456817Y-127279228D01* -X125456804Y-127279221D01* -X125329332Y-127226421D01* -X125329322Y-127226418D01* -X125193995Y-127199500D01* -X125193993Y-127199500D01* -X125056007Y-127199500D01* -X125056005Y-127199500D01* -X124920677Y-127226418D01* -X124920667Y-127226421D01* -X124793195Y-127279221D01* -X124793182Y-127279228D01* -X124678458Y-127355885D01* -X124678454Y-127355888D01* -X124580888Y-127453454D01* -X124580885Y-127453458D01* -X124504228Y-127568182D01* -X124504221Y-127568195D01* -X124451421Y-127695667D01* -X124451418Y-127695677D01* -X124424500Y-127831004D01* -X124424500Y-127831006D01* -X124424500Y-127831007D01* -X124424500Y-127968993D01* -X124424500Y-127968995D01* -X124424499Y-127968995D01* -X121575500Y-127968995D01* -X121575500Y-127968993D01* -X121575500Y-127831007D01* -X121575500Y-127831006D01* -X121575500Y-127831004D01* -X121548581Y-127695677D01* -X121548580Y-127695676D01* -X121548580Y-127695672D01* -X121548578Y-127695667D01* -X121495778Y-127568195D01* -X121495771Y-127568182D01* -X121419114Y-127453458D01* -X121419111Y-127453454D01* -X121321545Y-127355888D01* -X121321541Y-127355885D01* -X121206817Y-127279228D01* -X121206804Y-127279221D01* -X121079332Y-127226421D01* -X121079322Y-127226418D01* -X120943995Y-127199500D01* -X120943993Y-127199500D01* -X120806007Y-127199500D01* -X120806005Y-127199500D01* -X120670677Y-127226418D01* -X120670667Y-127226421D01* -X120543195Y-127279221D01* -X120543182Y-127279228D01* -X120443391Y-127345907D01* -X120376713Y-127366785D01* -X120309333Y-127348300D01* -X120262643Y-127296321D01* -X120250500Y-127242805D01* -X120250500Y-126893713D01* +X133317463Y-127123248D01* +X133153676Y-127013810D01* +X133125579Y-127002171D01* +X133071177Y-126958328D01* +X133049673Y-126893713D01* X145649500Y-126893713D01* X145649500Y-127106286D01* X145679598Y-127296321D01* @@ -849,191 +727,182 @@ X145844951Y-126292179D01* X145748444Y-126481585D01* X145682753Y-126683760D01* X145649500Y-126893713D01* -X120250500Y-126893713D01* -X120250500Y-125446453D01* -X124969500Y-125446453D01* -X124969500Y-125604146D01* -X125000261Y-125758789D01* -X125000264Y-125758801D01* -X125060602Y-125904472D01* -X125060609Y-125904485D01* -X125148210Y-126035588D01* -X125148213Y-126035592D01* -X125259707Y-126147086D01* -X125259711Y-126147089D01* -X125390814Y-126234690D01* -X125390827Y-126234697D01* -X125529603Y-126292179D01* -X125536503Y-126295037D01* -X125691153Y-126325799D01* -X125691156Y-126325800D01* -X125691158Y-126325800D01* -X125848844Y-126325800D01* -X125848845Y-126325799D01* -X126003497Y-126295037D01* -X126149179Y-126234694D01* -X126280289Y-126147089D01* -X126391789Y-126035589D01* -X126424821Y-125986153D01* -X137949500Y-125986153D01* -X137949500Y-126143846D01* -X137980261Y-126298489D01* -X137980264Y-126298501D01* -X138040602Y-126444172D01* -X138040609Y-126444185D01* -X138128210Y-126575288D01* -X138128213Y-126575292D01* -X138239707Y-126686786D01* -X138239711Y-126686789D01* -X138370814Y-126774390D01* -X138370827Y-126774397D01* -X138516498Y-126834735D01* -X138516503Y-126834737D01* -X138671153Y-126865499D01* -X138671156Y-126865500D01* -X138671158Y-126865500D01* -X138828844Y-126865500D01* -X138828845Y-126865499D01* -X138983497Y-126834737D01* -X139129179Y-126774394D01* -X139260289Y-126686789D01* -X139371789Y-126575289D01* -X139459394Y-126444179D01* -X139519737Y-126298497D01* -X139550500Y-126143842D01* -X139550500Y-125986158D01* -X139550500Y-125986155D01* -X139550499Y-125986153D01* -X139535585Y-125911175D01* -X139519737Y-125831503D01* -X139489623Y-125758801D01* -X139459397Y-125685827D01* -X139459390Y-125685814D01* -X139371789Y-125554711D01* -X139371786Y-125554707D01* -X139260292Y-125443213D01* -X139260288Y-125443210D01* -X139129185Y-125355609D01* -X139129172Y-125355602D01* -X138983501Y-125295264D01* -X138983489Y-125295261D01* -X138828845Y-125264500D01* -X138828842Y-125264500D01* -X138671158Y-125264500D01* -X138671155Y-125264500D01* -X138516510Y-125295261D01* -X138516498Y-125295264D01* -X138370827Y-125355602D01* -X138370814Y-125355609D01* -X138239711Y-125443210D01* -X138239707Y-125443213D01* -X138128213Y-125554707D01* -X138128210Y-125554711D01* -X138040609Y-125685814D01* -X138040602Y-125685827D01* -X137980264Y-125831498D01* -X137980261Y-125831510D01* -X137949500Y-125986153D01* -X126424821Y-125986153D01* -X126435688Y-125969890D01* -X126474921Y-125911175D01* -X126474921Y-125911174D01* -X126479389Y-125904486D01* -X126479390Y-125904485D01* -X126479394Y-125904479D01* -X126539737Y-125758797D01* -X126570500Y-125604142D01* -X126570500Y-125446458D01* -X126570500Y-125446455D01* -X126570499Y-125446453D01* -X126540425Y-125295263D01* -X126539737Y-125291803D01* -X126504802Y-125207462D01* -X126479397Y-125146127D01* -X126479390Y-125146114D01* -X126391789Y-125015011D01* -X126391786Y-125015007D01* -X126280292Y-124903513D01* -X126280288Y-124903510D01* -X126149185Y-124815909D01* -X126149172Y-124815902D01* -X126003501Y-124755564D01* -X126003489Y-124755561D01* -X125848845Y-124724800D01* -X125848842Y-124724800D01* -X125691158Y-124724800D01* -X125691155Y-124724800D01* -X125536510Y-124755561D01* -X125536498Y-124755564D01* -X125390827Y-124815902D01* -X125390814Y-124815909D01* -X125259711Y-124903510D01* -X125259707Y-124903513D01* -X125148213Y-125015007D01* -X125148210Y-125015011D01* -X125060609Y-125146114D01* -X125060602Y-125146127D01* -X125000264Y-125291798D01* -X125000261Y-125291810D01* -X124969500Y-125446453D01* -X120250500Y-125446453D01* -X120250500Y-122393713D01* -X121649500Y-122393713D01* -X121649500Y-122606287D01* -X121682754Y-122816243D01* -X121741267Y-122996328D01* -X121748444Y-123018414D01* -X121844951Y-123207820D01* -X121969890Y-123379786D01* -X122120213Y-123530109D01* -X122292179Y-123655048D01* -X122292181Y-123655049D01* -X122292184Y-123655051D01* -X122481588Y-123751557D01* -X122683757Y-123817246D01* -X122893713Y-123850500D01* -X122893714Y-123850500D01* -X123106286Y-123850500D01* -X123106287Y-123850500D01* -X123316243Y-123817246D01* -X123518412Y-123751557D01* -X123707816Y-123655051D01* -X123738739Y-123632584D01* -X123879786Y-123530109D01* -X123879788Y-123530106D01* -X123879792Y-123530104D01* -X124030104Y-123379792D01* -X124030106Y-123379788D01* -X124030109Y-123379786D01* -X124155048Y-123207820D01* -X124155047Y-123207820D01* -X124155051Y-123207816D01* -X124242467Y-123036253D01* -X128416200Y-123036253D01* -X128416200Y-123193946D01* -X128446961Y-123348589D01* -X128446964Y-123348601D01* -X128507302Y-123494272D01* -X128507309Y-123494285D01* -X128594910Y-123625388D01* -X128594913Y-123625392D01* -X128706407Y-123736886D01* -X128706411Y-123736889D01* -X128837514Y-123824490D01* -X128837527Y-123824497D01* -X128983198Y-123884835D01* -X128983203Y-123884837D01* -X129137853Y-123915599D01* -X129137856Y-123915600D01* -X129137858Y-123915600D01* -X129295544Y-123915600D01* -X129295545Y-123915599D01* -X129450197Y-123884837D01* -X129595879Y-123824494D01* -X129726989Y-123736889D01* -X129838489Y-123625389D01* -X129926094Y-123494279D01* -X129976949Y-123371504D01* +X133049673Y-126893713D01* +X133049114Y-126892034D01* +X133049035Y-126887611D01* +X133049035Y-126841160D01* +X133049034Y-126841158D01* +X133018273Y-126686515D01* +X133018272Y-126686508D01* +X132980932Y-126596360D01* +X132957932Y-126540832D01* +X132957925Y-126540819D01* +X132870324Y-126409716D01* +X132870321Y-126409712D01* +X132758827Y-126298218D01* +X132758823Y-126298215D01* +X132627720Y-126210614D01* +X132627707Y-126210607D01* +X132482036Y-126150269D01* +X132482024Y-126150266D01* +X132327380Y-126119505D01* +X132327377Y-126119505D01* +X132169693Y-126119505D01* +X132169690Y-126119505D01* +X132015045Y-126150266D01* +X132015033Y-126150269D01* +X131869362Y-126210607D01* +X131869349Y-126210614D01* +X131738246Y-126298215D01* +X131738242Y-126298218D01* +X131626748Y-126409712D01* +X131626745Y-126409716D01* +X131539144Y-126540819D01* +X131539137Y-126540832D01* +X131478799Y-126686503D01* +X131478796Y-126686515D01* +X131448035Y-126841158D01* +X120250500Y-126841158D01* +X120250500Y-126663399D01* +X120270185Y-126596360D01* +X120322989Y-126550605D01* +X120392147Y-126540661D01* +X120398692Y-126541782D01* +X120521155Y-126566142D01* +X120521158Y-126566142D01* +X120678844Y-126566142D01* +X120678845Y-126566141D01* +X120833497Y-126535379D01* +X120979179Y-126475036D01* +X121110289Y-126387431D01* +X121221789Y-126275931D01* +X121309394Y-126144821D01* +X121369737Y-125999139D01* +X121400500Y-125844484D01* +X121400500Y-125705047D01* +X121420185Y-125638008D01* +X121472989Y-125592253D01* +X121476986Y-125590512D01* +X121479179Y-125589604D01* +X121610289Y-125501999D01* +X121611510Y-125500777D01* +X121612306Y-125500342D01* +X121614993Y-125498138D01* +X121615411Y-125498647D01* +X121672828Y-125467288D01* +X121723389Y-125466835D01* +X121795896Y-125481258D01* +X121795899Y-125481258D01* +X121953585Y-125481258D01* +X121953586Y-125481257D01* +X122108238Y-125450495D01* +X122253920Y-125390152D01* +X122385030Y-125302547D01* +X122496530Y-125191047D01* +X122584135Y-125059937D01* +X122644478Y-124914255D01* +X122657557Y-124848499D01* +X122663790Y-124817169D01* +X124279500Y-124817169D01* +X124279500Y-124974862D01* +X124310261Y-125129505D01* +X124310264Y-125129517D01* +X124370602Y-125275188D01* +X124370609Y-125275201D01* +X124458210Y-125406304D01* +X124458213Y-125406308D01* +X124569707Y-125517802D01* +X124569711Y-125517805D01* +X124700814Y-125605406D01* +X124700827Y-125605413D01* +X124807264Y-125649500D01* +X124846503Y-125665753D01* +X124952313Y-125686800D01* +X125001153Y-125696515D01* +X125001156Y-125696516D01* +X125001158Y-125696516D01* +X125158844Y-125696516D01* +X125158845Y-125696515D01* +X125313497Y-125665753D01* +X125426166Y-125619083D01* +X125459172Y-125605413D01* +X125459172Y-125605412D01* +X125459179Y-125605410D01* +X125590289Y-125517805D01* +X125701789Y-125406305D01* +X125789394Y-125275195D01* +X125849737Y-125129513D01* +X125880500Y-124974858D01* +X125880500Y-124817174D01* +X125880500Y-124817171D01* +X125880499Y-124817169D01* +X125869048Y-124759600D01* +X125849737Y-124662519D01* +X125834513Y-124625764D01* +X125789397Y-124516843D01* +X125789390Y-124516830D01* +X125701789Y-124385727D01* +X125701786Y-124385723D01* +X125624713Y-124308650D01* +X125591228Y-124247327D01* +X125596212Y-124177635D01* +X125638084Y-124121702D01* +X125703548Y-124097285D01* +X125759847Y-124106408D01* +X125768701Y-124110076D01* +X125914458Y-124139069D01* +X125923351Y-124140838D01* +X125923354Y-124140839D01* +X125923356Y-124140839D01* +X126081042Y-124140839D01* +X126081043Y-124140838D01* +X126235695Y-124110076D01* +X126356098Y-124060204D01* +X126381370Y-124049736D01* +X126381370Y-124049735D01* +X126381377Y-124049733D01* +X126512487Y-123962128D01* +X126623987Y-123850628D01* +X126711592Y-123719518D01* +X126752336Y-123621153D01* +X128399500Y-123621153D01* +X128399500Y-123778846D01* +X128430261Y-123933489D01* +X128430264Y-123933501D01* +X128490602Y-124079172D01* +X128490609Y-124079185D01* +X128578210Y-124210288D01* +X128578213Y-124210292D01* +X128689707Y-124321786D01* +X128689711Y-124321789D01* +X128820814Y-124409390D01* +X128820827Y-124409397D01* +X128955062Y-124464998D01* +X128966503Y-124469737D01* +X129121153Y-124500499D01* +X129121156Y-124500500D01* +X129121158Y-124500500D01* +X129278844Y-124500500D01* +X129278845Y-124500499D01* +X129433497Y-124469737D01* +X129579179Y-124409394D01* +X129710289Y-124321789D01* +X129821789Y-124210289D01* +X129837603Y-124186622D01* +X129862242Y-124149748D01* +X129862242Y-124149747D01* +X129880981Y-124121702D01* +X129909394Y-124079179D01* +X129921593Y-124049729D01* +X129954054Y-123971360D01* +X129969737Y-123933497D01* +X130000500Y-123778842D01* +X130000500Y-123621158D01* +X130000500Y-123621155D01* +X130000499Y-123621153D01* +X129991087Y-123573836D01* +X129969737Y-123466503D01* +X129930388Y-123371504D01* X131680000Y-123371504D01* X131680000Y-123770000D01* X132380000Y-123770000D01* @@ -1088,13 +957,48 @@ X134185766Y-125125500D01* X134332135Y-125086281D01* X134463365Y-125010515D01* X134570515Y-124903365D01* -X134646281Y-124772135D01* -X134685500Y-124625766D01* -X134685500Y-124474234D01* +X134617980Y-124821153D01* +X136199500Y-124821153D01* +X136199500Y-124978846D01* +X136230261Y-125133489D01* +X136230264Y-125133501D01* +X136290602Y-125279172D01* +X136290609Y-125279185D01* +X136378210Y-125410288D01* +X136378213Y-125410292D01* +X136489707Y-125521786D01* +X136489711Y-125521789D01* +X136620814Y-125609390D01* +X136620827Y-125609397D01* +X136756887Y-125665754D01* +X136766503Y-125669737D01* +X136901124Y-125696515D01* +X136921153Y-125700499D01* +X136921156Y-125700500D01* +X136921158Y-125700500D01* +X137078844Y-125700500D01* +X137078845Y-125700499D01* +X137233497Y-125669737D01* +X137379179Y-125609394D01* +X137510289Y-125521789D01* +X137621789Y-125410289D01* +X137709394Y-125279179D01* +X137769737Y-125133497D01* +X137800500Y-124978842D01* +X137800500Y-124821158D01* +X137800500Y-124821155D01* +X137800499Y-124821153D01* +X137787182Y-124754205D01* +X137769737Y-124666503D01* +X137761540Y-124646713D01* +X137709397Y-124520827D01* +X137709390Y-124520814D01* +X137678266Y-124474234D01* X139314500Y-124474234D01* -X139314500Y-124625765D01* +X139314500Y-124625766D01* +X139325949Y-124668495D01* X139353719Y-124772136D01* -X139375615Y-124810060D01* +X139391602Y-124837750D01* X139429485Y-124903365D01* X139536635Y-125010515D01* X139667865Y-125086281D01* @@ -1127,25 +1031,62 @@ X141204204Y-124849556D01* X141280504Y-124870000D01* X141359496Y-124870000D01* X141435796Y-124849556D01* -X141504205Y-124810060D01* -X141560060Y-124754205D01* -X141570000Y-124736988D01* +X141501382Y-124811689D01* +X141499500Y-124821153D01* +X141499500Y-124978846D01* +X141530261Y-125133489D01* +X141530264Y-125133501D01* +X141560561Y-125206644D01* +X141570000Y-125254096D01* X141570000Y-125539862D01* -X141611690Y-125531569D01* -X141611692Y-125531569D01* -X141793671Y-125456192D01* -X141793684Y-125456185D01* -X141957462Y-125346751D01* -X141957466Y-125346748D01* -X142096748Y-125207466D01* -X142096751Y-125207462D01* -X142206185Y-125043684D01* -X142206192Y-125043671D01* -X142281569Y-124861693D01* -X142281572Y-124861681D01* -X142319999Y-124668495D01* -X142320000Y-124668492D01* -X142320000Y-124270000D01* +X141611689Y-125531570D01* +X141669386Y-125507671D01* +X141738856Y-125500202D01* +X141785731Y-125519130D01* +X141920814Y-125609390D01* +X141920827Y-125609397D01* +X142056887Y-125665754D01* +X142066503Y-125669737D01* +X142201124Y-125696515D01* +X142221153Y-125700499D01* +X142221156Y-125700500D01* +X142221158Y-125700500D01* +X142378844Y-125700500D01* +X142378845Y-125700499D01* +X142533497Y-125669737D01* +X142679179Y-125609394D01* +X142810289Y-125521789D01* +X142921789Y-125410289D01* +X143009394Y-125279179D01* +X143069737Y-125133497D01* +X143100500Y-124978842D01* +X143100500Y-124821158D01* +X143100500Y-124821155D01* +X143100499Y-124821153D01* +X143087182Y-124754205D01* +X143069737Y-124666503D01* +X143061540Y-124646713D01* +X143009397Y-124520827D01* +X143009390Y-124520814D01* +X142921789Y-124389711D01* +X142921786Y-124389707D01* +X142810292Y-124278213D01* +X142810288Y-124278210D01* +X142679185Y-124190609D01* +X142679172Y-124190602D01* +X142533501Y-124130264D01* +X142533489Y-124130261D01* +X142378845Y-124099500D01* +X142378842Y-124099500D01* +X142221158Y-124099500D01* +X142221155Y-124099500D01* +X142066510Y-124130261D01* +X142066498Y-124130264D01* +X141920827Y-124190602D01* +X141920815Y-124190609D01* +X141833276Y-124249102D01* +X141766599Y-124269980D01* +X141764385Y-124270000D01* X141620000Y-124270000D01* X141620000Y-123770000D01* X142320000Y-123770000D01* @@ -1202,7 +1143,7 @@ X140243367Y-124089487D01* X140243365Y-124089485D01* X140165162Y-124044334D01* X140112136Y-124013719D01* -X140038950Y-123994109D01* +X140019982Y-123989027D01* X139965766Y-123974500D01* X139814234Y-123974500D01* X139667863Y-124013719D01* @@ -1211,14 +1152,44 @@ X139536632Y-124089487D01* X139429487Y-124196632D01* X139429485Y-124196635D01* X139353719Y-124327863D01* +X139316975Y-124464998D01* X139314500Y-124474234D01* +X137678266Y-124474234D01* +X137621789Y-124389711D01* +X137621786Y-124389707D01* +X137510292Y-124278213D01* +X137510288Y-124278210D01* +X137379185Y-124190609D01* +X137379172Y-124190602D01* +X137233501Y-124130264D01* +X137233489Y-124130261D01* +X137078845Y-124099500D01* +X137078842Y-124099500D01* +X136921158Y-124099500D01* +X136921155Y-124099500D01* +X136766510Y-124130261D01* +X136766498Y-124130264D01* +X136620827Y-124190602D01* +X136620814Y-124190609D01* +X136489711Y-124278210D01* +X136489707Y-124278213D01* +X136378213Y-124389707D01* +X136378210Y-124389711D01* +X136290609Y-124520814D01* +X136290602Y-124520827D01* +X136230264Y-124666498D01* +X136230261Y-124666510D01* +X136199500Y-124821153D01* +X134617980Y-124821153D01* +X134646281Y-124772135D01* +X134685500Y-124625766D01* X134685500Y-124474234D01* X134646281Y-124327865D01* X134570515Y-124196635D01* X134463365Y-124089485D01* X134385162Y-124044334D01* X134332136Y-124013719D01* -X134258950Y-123994109D01* +X134239982Y-123989027D01* X134185766Y-123974500D01* X134034234Y-123974500D01* X133887863Y-124013719D01* @@ -1272,157 +1243,204 @@ X131793807Y-122996328D01* X131718430Y-123178306D01* X131718427Y-123178318D01* X131680000Y-123371504D01* -X129976949Y-123371504D01* -X129986437Y-123348597D01* -X130017200Y-123193942D01* -X130017200Y-123036258D01* -X130017200Y-123036255D01* -X130017199Y-123036253D01* -X129986438Y-122881610D01* -X129986437Y-122881603D01* -X129973347Y-122850000D01* -X129926097Y-122735927D01* -X129926090Y-122735914D01* -X129838489Y-122604811D01* -X129838486Y-122604807D01* -X129726992Y-122493313D01* -X129726988Y-122493310D01* -X129595885Y-122405709D01* -X129595872Y-122405702D01* -X129450201Y-122345364D01* -X129450189Y-122345361D01* -X129295545Y-122314600D01* -X129295542Y-122314600D01* -X129137858Y-122314600D01* -X129137855Y-122314600D01* -X128983210Y-122345361D01* -X128983198Y-122345364D01* -X128837527Y-122405702D01* -X128837514Y-122405709D01* -X128706411Y-122493310D01* -X128706407Y-122493313D01* -X128594913Y-122604807D01* -X128594910Y-122604811D01* -X128507309Y-122735914D01* -X128507302Y-122735927D01* -X128446964Y-122881598D01* -X128446961Y-122881610D01* -X128416200Y-123036253D01* -X124242467Y-123036253D01* +X129930388Y-123371504D01* +X129913302Y-123330255D01* +X129909395Y-123320823D01* +X129909390Y-123320814D01* +X129821789Y-123189711D01* +X129821786Y-123189707D01* +X129710292Y-123078213D01* +X129710288Y-123078210D01* +X129579185Y-122990609D01* +X129579172Y-122990602D01* +X129433501Y-122930264D01* +X129433489Y-122930261D01* +X129278845Y-122899500D01* +X129278842Y-122899500D01* +X129121158Y-122899500D01* +X129121155Y-122899500D01* +X128966510Y-122930261D01* +X128966498Y-122930264D01* +X128820827Y-122990602D01* +X128820814Y-122990609D01* +X128689711Y-123078210D01* +X128689707Y-123078213D01* +X128578213Y-123189707D01* +X128578210Y-123189711D01* +X128490609Y-123320814D01* +X128490602Y-123320827D01* +X128430264Y-123466498D01* +X128430261Y-123466510D01* +X128399500Y-123621153D01* +X126752336Y-123621153D01* +X126771935Y-123573836D01* +X126802698Y-123419181D01* +X126802698Y-123261497D01* +X126802698Y-123261494D01* +X126802697Y-123261492D01* +X126792020Y-123207816D01* +X126771935Y-123106842D01* +X126760075Y-123078210D01* +X126711595Y-122961166D01* +X126711588Y-122961153D01* +X126623987Y-122830050D01* +X126623984Y-122830046D01* +X126512490Y-122718552D01* +X126512486Y-122718549D01* +X126381383Y-122630948D01* +X126381370Y-122630941D01* +X126235699Y-122570603D01* +X126235687Y-122570600D01* +X126081043Y-122539839D01* +X126081040Y-122539839D01* +X125923356Y-122539839D01* +X125923353Y-122539839D01* +X125768708Y-122570600D01* +X125768696Y-122570603D01* +X125623025Y-122630941D01* +X125623012Y-122630948D01* +X125491909Y-122718549D01* +X125491905Y-122718552D01* +X125380411Y-122830046D01* +X125380408Y-122830050D01* +X125292807Y-122961153D01* +X125292800Y-122961166D01* +X125232462Y-123106837D01* +X125232459Y-123106849D01* +X125201698Y-123261492D01* +X125201698Y-123419185D01* +X125232459Y-123573828D01* +X125232462Y-123573840D01* +X125292800Y-123719511D01* +X125292807Y-123719524D01* +X125380408Y-123850627D01* +X125380411Y-123850631D01* +X125457484Y-123927704D01* +X125490969Y-123989027D01* +X125485985Y-124058719D01* +X125444113Y-124114652D01* +X125378649Y-124139069D01* +X125322352Y-124129947D01* +X125320114Y-124129020D01* +X125313497Y-124126279D01* +X125313493Y-124126278D01* +X125313489Y-124126277D01* +X125158845Y-124095516D01* +X125158842Y-124095516D01* +X125001158Y-124095516D01* +X125001155Y-124095516D01* +X124846510Y-124126277D01* +X124846498Y-124126280D01* +X124700827Y-124186618D01* +X124700814Y-124186625D01* +X124569711Y-124274226D01* +X124569707Y-124274229D01* +X124458213Y-124385723D01* +X124458210Y-124385727D01* +X124370609Y-124516830D01* +X124370602Y-124516843D01* +X124310264Y-124662514D01* +X124310261Y-124662526D01* +X124279500Y-124817169D01* +X122663790Y-124817169D01* +X122669813Y-124786891D01* +X122669813Y-124786890D01* +X122675241Y-124759602D01* +X122675241Y-124601913D01* +X122675240Y-124601911D01* +X122659110Y-124520821D01* +X122644478Y-124447261D01* +X122628966Y-124409812D01* +X122584138Y-124301585D01* +X122584131Y-124301572D01* +X122496530Y-124170469D01* +X122496527Y-124170465D01* +X122385033Y-124058971D01* +X122385029Y-124058968D01* +X122253926Y-123971367D01* +X122253913Y-123971360D01* +X122108242Y-123911022D01* +X122108230Y-123911019D01* +X121953586Y-123880258D01* +X121953583Y-123880258D01* +X121795899Y-123880258D01* +X121795896Y-123880258D01* +X121641251Y-123911019D01* +X121641239Y-123911022D01* +X121495568Y-123971360D01* +X121495555Y-123971367D01* +X121364455Y-124058966D01* +X121364446Y-124058973D01* +X121363216Y-124060204D01* +X121362414Y-124060641D01* +X121359748Y-124062830D01* +X121359332Y-124062324D01* +X121301890Y-124093684D01* +X121251353Y-124094133D01* +X121226188Y-124089127D01* +X121178842Y-124079710D01* +X121021158Y-124079710D01* +X121021155Y-124079710D01* +X120866510Y-124110471D01* +X120866498Y-124110474D01* +X120720827Y-124170812D01* +X120720814Y-124170819D01* +X120589711Y-124258420D01* +X120589707Y-124258423D01* +X120478213Y-124369917D01* +X120478206Y-124369926D01* +X120477597Y-124370838D01* +X120477155Y-124371207D01* +X120474347Y-124374629D01* +X120473697Y-124374096D01* +X120423982Y-124415639D01* +X120354656Y-124424342D01* +X120291631Y-124394183D01* +X120254916Y-124334737D01* +X120250500Y-124301940D01* +X120250500Y-122393713D01* +X121649500Y-122393713D01* +X121649500Y-122606287D01* +X121682754Y-122816243D01* +X121741267Y-122996328D01* +X121748444Y-123018414D01* +X121844951Y-123207820D01* +X121969890Y-123379786D01* +X122120213Y-123530109D01* +X122292179Y-123655048D01* +X122292181Y-123655049D01* +X122292184Y-123655051D01* +X122481588Y-123751557D01* +X122683757Y-123817246D01* +X122893713Y-123850500D01* +X122893714Y-123850500D01* +X123106286Y-123850500D01* +X123106287Y-123850500D01* +X123316243Y-123817246D01* +X123518412Y-123751557D01* +X123707816Y-123655051D01* +X123754473Y-123621153D01* +X123879786Y-123530109D01* +X123879788Y-123530106D01* +X123879792Y-123530104D01* +X124030104Y-123379792D01* +X124030106Y-123379788D01* +X124030109Y-123379786D01* +X124155048Y-123207820D01* +X124155047Y-123207820D01* +X124155051Y-123207816D01* X124251557Y-123018412D01* X124317246Y-122816243D01* X124350500Y-122606287D01* -X124350500Y-122393713D01* -X124317246Y-122183757D01* -X124251557Y-121981588D01* -X124155051Y-121792184D01* -X124155049Y-121792181D01* -X124155048Y-121792179D01* -X124030109Y-121620213D01* -X123881050Y-121471154D01* -X126499500Y-121471154D01* -X126499500Y-121628847D01* -X126530261Y-121783490D01* -X126530264Y-121783502D01* -X126590602Y-121929173D01* -X126590609Y-121929186D01* -X126678210Y-122060289D01* -X126678213Y-122060293D01* -X126789707Y-122171787D01* -X126789711Y-122171790D01* -X126920814Y-122259391D01* -X126920827Y-122259398D01* -X127066498Y-122319736D01* -X127066503Y-122319738D01* -X127195318Y-122345361D01* -X127221153Y-122350500D01* -X127221156Y-122350501D01* -X127221158Y-122350501D01* -X127378844Y-122350501D01* -X127378845Y-122350500D01* -X127533497Y-122319738D01* -X127679179Y-122259395D01* -X127810289Y-122171790D01* -X127921789Y-122060290D01* -X128009394Y-121929180D01* -X128069737Y-121783498D01* -X128100500Y-121628843D01* -X128100500Y-121623653D01* -X133849500Y-121623653D01* -X133849500Y-121781346D01* -X133880261Y-121935989D01* -X133880264Y-121936001D01* -X133940602Y-122081672D01* -X133940609Y-122081685D01* -X134028210Y-122212788D01* -X134028213Y-122212792D01* -X134139707Y-122324286D01* -X134139711Y-122324289D01* -X134270814Y-122411890D01* -X134270827Y-122411897D01* -X134416498Y-122472235D01* -X134416503Y-122472237D01* -X134556755Y-122500135D01* -X134571153Y-122502999D01* -X134571156Y-122503000D01* -X134571158Y-122503000D01* -X134728844Y-122503000D01* -X134728845Y-122502999D01* -X134883497Y-122472237D01* -X135029179Y-122411894D01* -X135160289Y-122324289D01* -X135243973Y-122240604D01* -X135305294Y-122207120D01* -X135374985Y-122212104D01* -X135379070Y-122213711D01* -X135516503Y-122270637D01* -X135671153Y-122301399D01* -X135671156Y-122301400D01* -X135671158Y-122301400D01* -X135828844Y-122301400D01* -X135828845Y-122301399D01* -X135983497Y-122270637D01* -X136123148Y-122212792D01* -X136129172Y-122210297D01* -X136129172Y-122210296D01* -X136129179Y-122210294D01* -X136260289Y-122122689D01* -X136371789Y-122011189D01* -X136459394Y-121880079D01* -X136496684Y-121790053D01* -X138649500Y-121790053D01* -X138649500Y-121947746D01* -X138680261Y-122102389D01* -X138680264Y-122102401D01* -X138740602Y-122248072D01* -X138740609Y-122248085D01* -X138828210Y-122379188D01* -X138828213Y-122379192D01* -X138939707Y-122490686D01* -X138939711Y-122490689D01* -X139070814Y-122578290D01* -X139070827Y-122578297D01* -X139216498Y-122638635D01* -X139216503Y-122638637D01* -X139371153Y-122669399D01* -X139371156Y-122669400D01* -X139371158Y-122669400D01* -X139528844Y-122669400D01* -X139528845Y-122669399D01* -X139683497Y-122638637D01* -X139796166Y-122591967D01* -X139829172Y-122578297D01* -X139829172Y-122578296D01* -X139829179Y-122578294D01* -X139960289Y-122490689D01* -X140025995Y-122424983D01* +X124350500Y-122424983D01* X144099500Y-122424983D01* X144099500Y-123775001D01* X144099501Y-123775018D01* X144110000Y-123877796D01* X144110001Y-123877799D01* -X144142045Y-123974500D01* -X144165186Y-124044334D01* +X144165185Y-124044331D01* +X144165187Y-124044336D01* +X144186682Y-124079185D01* X144257288Y-124193656D01* X144381344Y-124317712D01* X144530666Y-124409814D01* @@ -1431,7 +1449,7 @@ X144799991Y-124475500D01* X145600008Y-124475499D01* X145600016Y-124475498D01* X145600019Y-124475498D01* -X145656302Y-124469748D01* +X145656434Y-124469735D01* X145702797Y-124464999D01* X145869334Y-124409814D01* X146018656Y-124317712D01* @@ -1512,7 +1530,7 @@ X146018656Y-121882288D01* X145894310Y-121805591D01* X145869336Y-121790187D01* X145869331Y-121790185D01* -X145849127Y-121783490D01* +X145867862Y-121789698D01* X145702797Y-121735001D01* X145702795Y-121735000D01* X145600010Y-121724500D01* @@ -1526,135 +1544,19 @@ X144381342Y-121882289D01* X144257289Y-122006342D01* X144165187Y-122155663D01* X144165185Y-122155668D01* -X144148136Y-122207120D01* +X144137349Y-122239670D01* X144110001Y-122322203D01* X144110001Y-122322204D01* X144110000Y-122322204D01* X144099500Y-122424983D01* -X140025995Y-122424983D01* -X140071789Y-122379189D01* -X140159394Y-122248079D01* -X140219737Y-122102397D01* -X140250500Y-121947742D01* -X140250500Y-121790058D01* -X140250500Y-121790055D01* -X140250499Y-121790053D01* -X140237460Y-121724501D01* -X140219737Y-121635403D01* -X140219735Y-121635398D01* -X140159397Y-121489727D01* -X140159390Y-121489714D01* -X140071789Y-121358611D01* -X140071786Y-121358607D01* -X139960292Y-121247113D01* -X139960288Y-121247110D01* -X139829185Y-121159509D01* -X139829172Y-121159502D01* -X139683501Y-121099164D01* -X139683489Y-121099161D01* -X139528845Y-121068400D01* -X139528842Y-121068400D01* -X139371158Y-121068400D01* -X139371155Y-121068400D01* -X139216510Y-121099161D01* -X139216498Y-121099164D01* -X139070827Y-121159502D01* -X139070814Y-121159509D01* -X138939711Y-121247110D01* -X138939707Y-121247113D01* -X138828213Y-121358607D01* -X138828210Y-121358611D01* -X138740609Y-121489714D01* -X138740602Y-121489727D01* -X138680264Y-121635398D01* -X138680261Y-121635410D01* -X138649500Y-121790053D01* -X136496684Y-121790053D01* -X136519737Y-121734397D01* -X136550500Y-121579742D01* -X136550500Y-121422058D01* -X136550500Y-121422055D01* -X136550499Y-121422053D01* -X136519737Y-121267403D01* -X136511332Y-121247111D01* -X136459397Y-121121727D01* -X136459390Y-121121714D01* -X136371789Y-120990611D01* -X136371786Y-120990607D01* -X136260292Y-120879113D01* -X136260288Y-120879110D01* -X136129185Y-120791509D01* -X136129172Y-120791502D01* -X135983501Y-120731164D01* -X135983489Y-120731161D01* -X135828845Y-120700400D01* -X135828842Y-120700400D01* -X135671158Y-120700400D01* -X135671155Y-120700400D01* -X135516510Y-120731161D01* -X135516498Y-120731164D01* -X135370827Y-120791502D01* -X135370814Y-120791509D01* -X135239711Y-120879110D01* -X135239707Y-120879113D01* -X135156027Y-120962794D01* -X135094704Y-120996279D01* -X135025012Y-120991295D01* -X135020894Y-120989674D01* -X134883501Y-120932764D01* -X134883489Y-120932761D01* -X134728845Y-120902000D01* -X134728842Y-120902000D01* -X134571158Y-120902000D01* -X134571155Y-120902000D01* -X134416510Y-120932761D01* -X134416498Y-120932764D01* -X134270827Y-120993102D01* -X134270814Y-120993109D01* -X134139711Y-121080710D01* -X134139707Y-121080713D01* -X134028213Y-121192207D01* -X134028210Y-121192211D01* -X133940609Y-121323314D01* -X133940602Y-121323327D01* -X133880264Y-121468998D01* -X133880261Y-121469010D01* -X133849500Y-121623653D01* -X128100500Y-121623653D01* -X128100500Y-121471159D01* -X128100500Y-121471156D01* -X128100499Y-121471154D01* -X128090733Y-121422058D01* -X128069737Y-121316504D01* -X128041546Y-121248444D01* -X128009397Y-121170828D01* -X128009390Y-121170815D01* -X127921789Y-121039712D01* -X127921786Y-121039708D01* -X127810292Y-120928214D01* -X127810288Y-120928211D01* -X127679185Y-120840610D01* -X127679172Y-120840603D01* -X127533501Y-120780265D01* -X127533489Y-120780262D01* -X127378845Y-120749501D01* -X127378842Y-120749501D01* -X127221158Y-120749501D01* -X127221155Y-120749501D01* -X127066510Y-120780262D01* -X127066498Y-120780265D01* -X126920827Y-120840603D01* -X126920814Y-120840610D01* -X126789711Y-120928211D01* -X126789707Y-120928214D01* -X126678213Y-121039708D01* -X126678210Y-121039712D01* -X126590609Y-121170815D01* -X126590602Y-121170828D01* -X126530264Y-121316499D01* -X126530261Y-121316511D01* -X126499500Y-121471154D01* -X123881050Y-121471154D01* +X124350500Y-122424983D01* +X124350500Y-122393713D01* +X124317246Y-122183757D01* +X124251557Y-121981588D01* +X124155051Y-121792184D01* +X124155049Y-121792181D01* +X124155048Y-121792179D01* +X124030109Y-121620213D01* X123879786Y-121469890D01* X123707820Y-121344951D01* X123518414Y-121248444D01* @@ -1668,8 +1570,6 @@ X123106287Y-121149500D01* X122893713Y-121149500D01* X122845042Y-121157208D01* X122683760Y-121182753D01* -X122683757Y-121182754D01* -X122485688Y-121247111D01* X122481585Y-121248444D01* X122292179Y-121344951D01* X122120213Y-121469890D01* @@ -1677,2490 +1577,3501 @@ X121969890Y-121620213D01* X121844951Y-121792179D01* X121748444Y-121981585D01* X121682753Y-122183760D01* -X121661216Y-122319739D01* +X121660826Y-122322203D01* X121649500Y-122393713D01* X120250500Y-122393713D01* -X120250500Y-119368591D01* -X129408540Y-119368591D01* -X129442112Y-119391023D01* -X129560401Y-119440020D01* -X129560409Y-119440022D01* -X129685976Y-119464999D01* -X129685980Y-119465000D01* -X129814020Y-119465000D01* -X129814023Y-119464999D01* -X129939590Y-119440022D01* -X129939594Y-119440021D01* -X130057891Y-119391020D01* -X130057898Y-119391016D01* -X130091458Y-119368591D01* -X130091459Y-119368590D01* -X129750001Y-119027132D01* -X129750000Y-119027132D01* -X129408540Y-119368591D01* -X120250500Y-119368591D01* -X120250500Y-118750976D01* -X129100000Y-118750976D01* -X129100000Y-118879023D01* -X129124977Y-119004590D01* -X129124979Y-119004598D01* -X129173976Y-119122886D01* -X129173981Y-119122896D01* -X129196407Y-119156458D01* -X129196408Y-119156458D01* -X129537868Y-118815000D01* -X129537868Y-118814999D01* -X129517978Y-118795109D01* -X129650000Y-118795109D01* -X129650000Y-118834891D01* -X129665224Y-118871645D01* -X129693355Y-118899776D01* -X129730109Y-118915000D01* -X129769891Y-118915000D01* -X129806645Y-118899776D01* -X129834776Y-118871645D01* -X129850000Y-118834891D01* -X129850000Y-118814999D01* -X129962132Y-118814999D01* -X129962132Y-118815000D01* -X130303590Y-119156459D01* -X130303591Y-119156458D01* -X130326016Y-119122898D01* -X130326020Y-119122891D01* -X130375021Y-119004594D01* -X130375022Y-119004590D01* -X130399999Y-118879023D01* -X130400000Y-118879020D01* -X130400000Y-118858553D01* -X133010100Y-118858553D01* -X133010100Y-119016246D01* -X133040861Y-119170889D01* -X133040864Y-119170901D01* -X133101202Y-119316572D01* -X133101209Y-119316585D01* -X133188810Y-119447688D01* -X133188813Y-119447692D01* -X133300307Y-119559186D01* -X133300311Y-119559189D01* -X133431414Y-119646790D01* -X133431427Y-119646797D01* -X133577098Y-119707135D01* -X133577103Y-119707137D01* -X133731753Y-119737899D01* -X133731756Y-119737900D01* -X133731758Y-119737900D01* -X133889444Y-119737900D01* -X133889445Y-119737899D01* -X134044097Y-119707137D01* -X134189779Y-119646794D01* -X134320889Y-119559189D01* -X134432389Y-119447689D01* -X134519994Y-119316579D01* -X134580337Y-119170897D01* -X134611100Y-119016242D01* -X134611100Y-118858558D01* -X134611100Y-118858555D01* -X134611099Y-118858553D01* -X134602436Y-118815000D01* -X134580337Y-118703903D01* -X134547821Y-118625401D01* -X134519997Y-118558227D01* -X134519990Y-118558214D01* -X134432389Y-118427111D01* -X134432386Y-118427107D01* -X134320892Y-118315613D01* -X134320888Y-118315610D01* -X134189785Y-118228009D01* -X134189772Y-118228002D01* -X134044101Y-118167664D01* -X134044089Y-118167661D01* -X133889445Y-118136900D01* -X133889442Y-118136900D01* -X133731758Y-118136900D01* -X133731755Y-118136900D01* -X133577110Y-118167661D01* -X133577098Y-118167664D01* -X133431427Y-118228002D01* -X133431414Y-118228009D01* -X133300311Y-118315610D01* -X133300307Y-118315613D01* -X133188813Y-118427107D01* -X133188810Y-118427111D01* -X133101209Y-118558214D01* -X133101202Y-118558227D01* -X133040864Y-118703898D01* -X133040861Y-118703910D01* -X133010100Y-118858553D01* -X130400000Y-118858553D01* -X130400000Y-118750980D01* -X130399999Y-118750976D01* -X130375022Y-118625409D01* -X130375020Y-118625401D01* -X130326023Y-118507112D01* -X130303591Y-118473540D01* -X129962132Y-118814999D01* -X129850000Y-118814999D01* -X129850000Y-118795109D01* -X129834776Y-118758355D01* -X129806645Y-118730224D01* -X129769891Y-118715000D01* -X129730109Y-118715000D01* -X129693355Y-118730224D01* -X129665224Y-118758355D01* -X129650000Y-118795109D01* -X129517978Y-118795109D01* -X129196408Y-118473539D01* -X129196407Y-118473540D01* -X129173978Y-118507109D01* -X129124979Y-118625401D01* -X129124977Y-118625409D01* -X129100000Y-118750976D01* -X120250500Y-118750976D01* -X120250500Y-117511888D01* -X122573765Y-117511888D01* -X122573765Y-117669581D01* -X122604526Y-117824224D01* -X122604529Y-117824236D01* -X122664867Y-117969907D01* -X122664874Y-117969920D01* -X122752475Y-118101023D01* -X122752478Y-118101027D01* -X122863972Y-118212521D01* -X122863976Y-118212524D01* -X122995079Y-118300125D01* -X122995092Y-118300132D01* -X123140763Y-118360470D01* -X123140768Y-118360472D01* -X123295418Y-118391234D01* -X123295421Y-118391235D01* -X123295423Y-118391235D01* -X123453109Y-118391235D01* -X123453110Y-118391234D01* -X123607762Y-118360472D01* -X123717542Y-118315000D01* -X129462132Y-118315000D01* -X129750000Y-118602868D01* -X130037868Y-118315000D01* -X129750000Y-118027132D01* -X129462132Y-118315000D01* -X123717542Y-118315000D01* -X123753444Y-118300129D01* -X123884554Y-118212524D01* -X123996054Y-118101024D01* -X124083659Y-117969914D01* -X124144002Y-117824232D01* -X124158573Y-117750976D01* -X129100000Y-117750976D01* -X129100000Y-117879023D01* -X129124977Y-118004590D01* -X129124979Y-118004598D01* -X129173976Y-118122886D01* -X129173981Y-118122896D01* -X129196407Y-118156458D01* -X129196408Y-118156458D01* -X129537868Y-117815000D01* -X129537868Y-117814999D01* -X129517978Y-117795109D01* -X129650000Y-117795109D01* -X129650000Y-117834891D01* -X129665224Y-117871645D01* -X129693355Y-117899776D01* -X129730109Y-117915000D01* -X129769891Y-117915000D01* -X129806645Y-117899776D01* -X129834776Y-117871645D01* -X129850000Y-117834891D01* -X129850000Y-117814999D01* -X129962132Y-117814999D01* -X129962132Y-117815000D01* -X130303590Y-118156459D01* -X130303591Y-118156458D01* -X130326016Y-118122898D01* -X130326020Y-118122891D01* -X130375021Y-118004594D01* -X130375022Y-118004590D01* -X130399999Y-117879023D01* -X130400000Y-117879020D01* -X130400000Y-117750980D01* -X130399999Y-117750976D01* -X130375022Y-117625409D01* -X130375020Y-117625401D01* -X130326023Y-117507112D01* -X130303591Y-117473540D01* -X129962132Y-117814999D01* -X129850000Y-117814999D01* -X129850000Y-117795109D01* -X129834776Y-117758355D01* -X129806645Y-117730224D01* -X129769891Y-117715000D01* -X129730109Y-117715000D01* -X129693355Y-117730224D01* -X129665224Y-117758355D01* -X129650000Y-117795109D01* -X129517978Y-117795109D01* -X129196408Y-117473539D01* -X129196407Y-117473540D01* -X129173978Y-117507109D01* -X129124979Y-117625401D01* -X129124977Y-117625409D01* -X129100000Y-117750976D01* -X124158573Y-117750976D01* -X124165845Y-117714416D01* -X124198230Y-117652507D01* -X124234205Y-117628007D01* -X124233808Y-117627264D01* -X124239167Y-117624398D01* -X124239179Y-117624394D01* -X124370289Y-117536789D01* -X124481789Y-117425289D01* -X124569394Y-117294179D01* -X124577669Y-117274201D01* -X124582969Y-117261408D01* -X129408539Y-117261408D01* -X129750000Y-117602868D01* -X129750001Y-117602868D01* -X130091458Y-117261408D01* -X130091458Y-117261407D01* -X130057896Y-117238981D01* -X130057886Y-117238976D01* -X129939598Y-117189979D01* -X129939590Y-117189977D01* -X129814023Y-117165000D01* -X129685976Y-117165000D01* -X129560409Y-117189977D01* -X129560401Y-117189979D01* -X129442109Y-117238978D01* -X129408540Y-117261407D01* -X129408539Y-117261408D01* -X124582969Y-117261408D01* -X124583483Y-117260166D01* -X124583483Y-117260164D01* -X124592258Y-117238981D01* -X124629737Y-117148497D01* -X124660500Y-116993842D01* -X124660500Y-116836158D01* -X124660500Y-116836155D01* -X124660499Y-116836153D01* -X124629738Y-116681510D01* -X124629738Y-116681508D01* -X124629737Y-116681503D01* -X124629735Y-116681498D01* -X124569397Y-116535827D01* -X124569390Y-116535814D01* -X124481789Y-116404711D01* -X124481786Y-116404707D01* -X124370292Y-116293213D01* -X124370288Y-116293210D01* -X124239185Y-116205609D01* -X124239172Y-116205602D01* -X124093501Y-116145264D01* -X124093489Y-116145261D01* -X123938845Y-116114500D01* -X123938842Y-116114500D01* -X123781158Y-116114500D01* -X123781155Y-116114500D01* -X123626510Y-116145261D01* -X123626498Y-116145264D01* -X123480827Y-116205602D01* -X123480814Y-116205609D01* -X123349711Y-116293210D01* -X123349707Y-116293213D01* -X123238213Y-116404707D01* -X123238210Y-116404711D01* -X123150609Y-116535814D01* -X123150602Y-116535827D01* -X123090264Y-116681498D01* -X123090261Y-116681508D01* -X123068419Y-116791315D01* -X123036034Y-116853226D01* -X123000061Y-116877732D01* -X123000456Y-116878471D01* -X122995079Y-116881344D01* -X122863976Y-116968945D01* -X122863972Y-116968948D01* -X122752478Y-117080442D01* -X122752475Y-117080446D01* -X122664874Y-117211549D01* -X122664867Y-117211562D01* -X122604529Y-117357233D01* -X122604526Y-117357245D01* -X122573765Y-117511888D01* -X120250500Y-117511888D01* -X120250500Y-114701540D01* -X145554200Y-114701540D01* -X145554200Y-114848459D01* -X145582858Y-114992534D01* -X145582861Y-114992544D01* -X145639078Y-115128266D01* -X145639083Y-115128275D01* -X145720698Y-115250419D01* -X145720701Y-115250423D01* -X145824576Y-115354298D01* -X145824580Y-115354301D01* -X145946724Y-115435916D01* -X145946730Y-115435919D01* -X145946731Y-115435920D01* -X146082458Y-115492140D01* -X146226540Y-115520799D01* -X146226544Y-115520800D01* -X146226545Y-115520800D01* -X146373456Y-115520800D01* -X146373457Y-115520799D01* -X146517542Y-115492140D01* -X146653269Y-115435920D01* -X146775420Y-115354301D01* -X146879301Y-115250420D01* -X146960920Y-115128269D01* -X147017140Y-114992542D01* -X147045800Y-114848455D01* -X147045800Y-114701545D01* -X147017140Y-114557458D01* -X146963574Y-114428138D01* -X146960921Y-114421733D01* -X146960916Y-114421724D01* -X146879301Y-114299580D01* -X146879298Y-114299576D01* -X146775423Y-114195701D01* -X146775419Y-114195698D01* -X146653275Y-114114083D01* -X146653266Y-114114078D01* -X146517544Y-114057861D01* -X146517545Y-114057861D01* -X146517542Y-114057860D01* -X146517538Y-114057859D01* -X146517534Y-114057858D01* -X146373459Y-114029200D01* -X146373455Y-114029200D01* -X146226545Y-114029200D01* -X146226540Y-114029200D01* -X146082465Y-114057858D01* -X146082455Y-114057861D01* -X145946733Y-114114078D01* -X145946724Y-114114083D01* -X145824580Y-114195698D01* -X145824576Y-114195701D01* -X145720701Y-114299576D01* -X145720698Y-114299580D01* -X145639083Y-114421724D01* -X145639078Y-114421733D01* -X145582861Y-114557455D01* -X145582858Y-114557465D01* -X145554200Y-114701540D01* -X120250500Y-114701540D01* -X120250500Y-113579553D01* -X123099500Y-113579553D01* -X123099500Y-113737246D01* -X123130261Y-113891889D01* -X123130264Y-113891901D01* -X123190602Y-114037572D01* -X123190609Y-114037585D01* -X123278210Y-114168688D01* -X123278213Y-114168692D01* -X123389707Y-114280186D01* -X123389711Y-114280189D01* -X123520814Y-114367790D01* -X123520827Y-114367797D01* -X123651037Y-114421731D01* -X123666503Y-114428137D01* -X123821153Y-114458899D01* -X123821156Y-114458900D01* -X123821158Y-114458900D01* -X123978844Y-114458900D01* -X123978845Y-114458899D01* -X124133497Y-114428137D01* -X124279179Y-114367794D01* -X124410289Y-114280189D01* -X124521789Y-114168689D01* -X124609394Y-114037579D01* -X124669737Y-113891897D01* -X124700500Y-113737242D01* -X124700500Y-113579558D01* -X124700500Y-113579555D01* -X124700499Y-113579553D01* -X124669738Y-113424910D01* -X124669737Y-113424903D01* -X124669735Y-113424898D01* -X124609397Y-113279227D01* -X124609390Y-113279214D01* -X124521789Y-113148111D01* -X124521786Y-113148107D01* -X124410292Y-113036613D01* -X124410288Y-113036610D01* -X124279185Y-112949009D01* -X124279172Y-112949002D01* -X124133501Y-112888664D01* -X124133489Y-112888661D01* -X123978845Y-112857900D01* -X123978842Y-112857900D01* -X123821158Y-112857900D01* -X123821155Y-112857900D01* -X123666510Y-112888661D01* -X123666498Y-112888664D01* -X123520827Y-112949002D01* -X123520814Y-112949009D01* -X123389711Y-113036610D01* -X123389707Y-113036613D01* -X123278213Y-113148107D01* -X123278210Y-113148111D01* -X123190609Y-113279214D01* -X123190602Y-113279227D01* -X123130264Y-113424898D01* -X123130261Y-113424910D01* -X123099500Y-113579553D01* -X120250500Y-113579553D01* -X120250500Y-112221153D01* -X131149500Y-112221153D01* -X131149500Y-112378846D01* -X131180261Y-112533489D01* -X131180264Y-112533501D01* -X131240602Y-112679172D01* -X131240609Y-112679185D01* -X131328210Y-112810288D01* -X131328213Y-112810292D01* -X131439707Y-112921786D01* -X131439711Y-112921789D01* -X131570814Y-113009390D01* -X131570827Y-113009397D01* -X131716498Y-113069735D01* -X131716503Y-113069737D01* -X131871153Y-113100499D01* -X131871156Y-113100500D01* -X131871158Y-113100500D01* -X132028844Y-113100500D01* -X132028845Y-113100499D01* -X132183497Y-113069737D01* -X132329179Y-113009394D01* -X132460289Y-112921789D01* -X132571789Y-112810289D01* -X132659394Y-112679179D01* -X132719737Y-112533497D01* -X132750500Y-112378842D01* -X132750500Y-112221158D01* -X132750500Y-112221155D01* -X132750499Y-112221153D01* -X132719738Y-112066510D01* -X132719737Y-112066503D01* -X132719735Y-112066498D01* -X132659397Y-111920827D01* -X132659390Y-111920814D01* -X132571789Y-111789711D01* -X132571786Y-111789707D01* -X132460292Y-111678213D01* -X132460288Y-111678210D01* -X132329185Y-111590609D01* -X132329172Y-111590602D01* -X132183501Y-111530264D01* -X132183489Y-111530261D01* -X132028845Y-111499500D01* -X132028842Y-111499500D01* -X131871158Y-111499500D01* -X131871155Y-111499500D01* -X131716510Y-111530261D01* -X131716498Y-111530264D01* -X131570827Y-111590602D01* -X131570814Y-111590609D01* -X131439711Y-111678210D01* -X131439707Y-111678213D01* -X131328213Y-111789707D01* -X131328210Y-111789711D01* -X131240609Y-111920814D01* -X131240602Y-111920827D01* -X131180264Y-112066498D01* -X131180261Y-112066510D01* -X131149500Y-112221153D01* -X120250500Y-112221153D01* -X120250500Y-110902753D01* -X140316200Y-110902753D01* -X140316200Y-111060446D01* -X140346961Y-111215089D01* -X140346964Y-111215101D01* -X140407302Y-111360772D01* -X140407309Y-111360785D01* -X140494910Y-111491888D01* -X140494913Y-111491892D01* -X140606407Y-111603386D01* -X140606411Y-111603389D01* -X140737514Y-111690990D01* -X140737527Y-111690997D01* -X140883198Y-111751335D01* -X140883203Y-111751337D01* -X141037853Y-111782099D01* -X141037856Y-111782100D01* -X141037858Y-111782100D01* -X141195544Y-111782100D01* -X141195545Y-111782099D01* -X141288280Y-111763653D01* -X147271700Y-111763653D01* -X147271700Y-111921346D01* -X147302461Y-112075989D01* -X147302464Y-112076001D01* -X147362802Y-112221672D01* -X147362809Y-112221685D01* -X147450410Y-112352788D01* -X147450413Y-112352792D01* -X147561907Y-112464286D01* -X147561911Y-112464289D01* -X147693014Y-112551890D01* -X147693027Y-112551897D01* -X147838698Y-112612235D01* -X147838703Y-112612237D01* -X147993353Y-112642999D01* -X147993356Y-112643000D01* -X147993358Y-112643000D01* -X148151044Y-112643000D01* -X148151045Y-112642999D01* -X148305697Y-112612237D01* -X148451379Y-112551894D01* -X148582489Y-112464289D01* -X148693989Y-112352789D01* -X148781594Y-112221679D01* -X148841937Y-112075997D01* -X148872700Y-111921342D01* -X148872700Y-111763658D01* -X148872700Y-111763655D01* -X148872699Y-111763653D01* -X148841938Y-111609010D01* -X148841937Y-111609003D01* -X148834315Y-111590602D01* -X148781597Y-111463327D01* -X148781590Y-111463314D01* -X148693989Y-111332211D01* -X148693986Y-111332207D01* -X148582492Y-111220713D01* -X148582488Y-111220710D01* -X148451385Y-111133109D01* -X148451372Y-111133102D01* -X148305701Y-111072764D01* -X148305689Y-111072761D01* -X148151045Y-111042000D01* -X148151042Y-111042000D01* -X147993358Y-111042000D01* -X147993355Y-111042000D01* -X147838710Y-111072761D01* -X147838698Y-111072764D01* -X147693027Y-111133102D01* -X147693014Y-111133109D01* -X147561911Y-111220710D01* -X147561907Y-111220713D01* -X147450413Y-111332207D01* -X147450410Y-111332211D01* -X147362809Y-111463314D01* -X147362802Y-111463327D01* -X147302464Y-111608998D01* -X147302461Y-111609010D01* -X147271700Y-111763653D01* -X141288280Y-111763653D01* -X141350197Y-111751337D01* -X141495879Y-111690994D01* -X141515012Y-111678210D01* -X141550551Y-111654464D01* -X141589758Y-111628265D01* -X141626989Y-111603389D01* -X141738489Y-111491889D01* -X141826094Y-111360779D01* -X141886437Y-111215097D01* -X141917200Y-111060442D01* -X141917200Y-110902758D01* -X141917200Y-110902755D01* -X141917199Y-110902753D01* -X141886438Y-110748110D01* -X141886437Y-110748103D01* -X141886435Y-110748098D01* -X141826097Y-110602427D01* -X141826090Y-110602414D01* -X141738489Y-110471311D01* -X141738486Y-110471307D01* -X141626992Y-110359813D01* -X141626988Y-110359810D01* -X141495885Y-110272209D01* -X141495872Y-110272202D01* -X141350201Y-110211864D01* -X141350189Y-110211861D01* -X141195545Y-110181100D01* -X141195542Y-110181100D01* -X141037858Y-110181100D01* -X141037855Y-110181100D01* -X140883210Y-110211861D01* -X140883198Y-110211864D01* -X140737527Y-110272202D01* -X140737514Y-110272209D01* -X140606411Y-110359810D01* -X140606407Y-110359813D01* -X140494913Y-110471307D01* -X140494910Y-110471311D01* -X140407309Y-110602414D01* -X140407302Y-110602427D01* -X140346964Y-110748098D01* -X140346961Y-110748110D01* -X140316200Y-110902753D01* -X120250500Y-110902753D01* -X120250500Y-109621540D01* -X144538200Y-109621540D01* -X144538200Y-109768459D01* -X144566858Y-109912534D01* -X144566861Y-109912544D01* -X144623078Y-110048266D01* -X144623083Y-110048275D01* -X144704698Y-110170419D01* -X144704701Y-110170423D01* -X144808576Y-110274298D01* -X144808580Y-110274301D01* -X144930724Y-110355916D01* -X144930733Y-110355921D01* -X144955800Y-110366304D01* -X145066458Y-110412140D01* -X145210540Y-110440799D01* -X145210544Y-110440800D01* -X145210545Y-110440800D01* -X145357456Y-110440800D01* -X145357457Y-110440799D01* -X145501542Y-110412140D01* -X145637269Y-110355920D01* -X145759420Y-110274301D01* -X145863301Y-110170420D01* -X145944920Y-110048269D01* -X146001140Y-109912542D01* -X146029800Y-109768455D01* -X146029800Y-109621545D01* -X146029799Y-109621540D01* -X146570200Y-109621540D01* -X146570200Y-109768459D01* -X146598858Y-109912534D01* -X146598861Y-109912544D01* -X146655078Y-110048266D01* -X146655083Y-110048275D01* -X146736698Y-110170419D01* -X146736701Y-110170423D01* -X146840576Y-110274298D01* -X146840580Y-110274301D01* -X146962724Y-110355916D01* -X146962733Y-110355921D01* -X146987800Y-110366304D01* -X147098458Y-110412140D01* -X147242540Y-110440799D01* -X147242544Y-110440800D01* -X147242545Y-110440800D01* -X147389456Y-110440800D01* -X147389457Y-110440799D01* -X147533542Y-110412140D01* -X147669269Y-110355920D01* -X147791420Y-110274301D01* -X147895301Y-110170420D01* -X147976920Y-110048269D01* -X148033140Y-109912542D01* -X148061800Y-109768455D01* -X148061800Y-109621545D01* -X148033140Y-109477458D01* -X147976920Y-109341731D01* -X147976919Y-109341730D01* -X147976916Y-109341724D01* -X147895301Y-109219580D01* -X147895298Y-109219576D01* -X147791423Y-109115701D01* -X147791419Y-109115698D01* -X147669275Y-109034083D01* -X147669266Y-109034078D01* -X147533544Y-108977861D01* -X147533545Y-108977861D01* -X147533542Y-108977860D01* -X147533538Y-108977859D01* -X147533534Y-108977858D01* -X147389459Y-108949200D01* -X147389455Y-108949200D01* -X147242545Y-108949200D01* -X147242540Y-108949200D01* -X147098465Y-108977858D01* -X147098455Y-108977861D01* -X146962733Y-109034078D01* -X146962724Y-109034083D01* -X146840580Y-109115698D01* -X146840576Y-109115701D01* -X146736701Y-109219576D01* -X146736698Y-109219580D01* -X146655083Y-109341724D01* -X146655078Y-109341733D01* -X146598861Y-109477455D01* -X146598858Y-109477465D01* -X146570200Y-109621540D01* -X146029799Y-109621540D01* -X146001140Y-109477458D01* -X145944920Y-109341731D01* -X145944919Y-109341730D01* -X145944916Y-109341724D01* -X145863301Y-109219580D01* -X145863298Y-109219576D01* -X145759423Y-109115701D01* -X145759419Y-109115698D01* -X145637275Y-109034083D01* -X145637266Y-109034078D01* -X145501544Y-108977861D01* -X145501545Y-108977861D01* -X145501542Y-108977860D01* -X145501538Y-108977859D01* -X145501534Y-108977858D01* -X145357459Y-108949200D01* -X145357455Y-108949200D01* -X145210545Y-108949200D01* -X145210540Y-108949200D01* -X145066465Y-108977858D01* -X145066455Y-108977861D01* -X144930733Y-109034078D01* -X144930724Y-109034083D01* -X144808580Y-109115698D01* -X144808576Y-109115701D01* -X144704701Y-109219576D01* -X144704698Y-109219580D01* -X144623083Y-109341724D01* -X144623078Y-109341733D01* -X144566861Y-109477455D01* -X144566858Y-109477465D01* -X144538200Y-109621540D01* -X120250500Y-109621540D01* -X120250500Y-108257353D01* -X134974800Y-108257353D01* -X134974800Y-108415046D01* -X135005561Y-108569689D01* -X135005564Y-108569701D01* -X135065902Y-108715372D01* -X135065909Y-108715385D01* -X135153510Y-108846488D01* -X135153513Y-108846492D01* -X135265007Y-108957986D01* -X135265011Y-108957989D01* -X135396114Y-109045590D01* -X135396127Y-109045597D01* -X135541798Y-109105935D01* -X135541803Y-109105937D01* -X135696453Y-109136699D01* -X135696456Y-109136700D01* -X135696458Y-109136700D01* -X135854144Y-109136700D01* -X135854145Y-109136699D01* -X136008797Y-109105937D01* -X136154479Y-109045594D01* -X136285589Y-108957989D01* -X136397089Y-108846489D01* -X136484694Y-108715379D01* -X136545037Y-108569697D01* -X136575800Y-108415042D01* -X136575800Y-108257358D01* -X136575800Y-108257355D01* -X136575799Y-108257353D01* -X136573438Y-108245486D01* -X136545037Y-108102703D01* -X136545035Y-108102698D01* -X136484697Y-107957027D01* -X136484690Y-107957014D01* -X136397089Y-107825911D01* -X136397086Y-107825907D01* -X136285592Y-107714413D01* -X136285588Y-107714410D01* -X136177022Y-107641868D01* -X136154485Y-107626809D01* -X136154472Y-107626802D01* -X136008801Y-107566464D01* -X136008789Y-107566461D01* -X135900160Y-107544853D01* -X145050300Y-107544853D01* -X145050300Y-107702546D01* -X145081061Y-107857189D01* -X145081064Y-107857201D01* -X145141402Y-108002872D01* -X145141409Y-108002885D01* -X145229010Y-108133988D01* -X145229013Y-108133992D01* -X145340507Y-108245486D01* -X145340511Y-108245489D01* -X145471614Y-108333090D01* -X145471627Y-108333097D01* -X145617298Y-108393435D01* -X145617303Y-108393437D01* -X145771953Y-108424199D01* -X145771956Y-108424200D01* -X145771958Y-108424200D01* -X145929644Y-108424200D01* -X145929645Y-108424199D01* -X146084297Y-108393437D01* -X146229979Y-108333094D01* -X146361089Y-108245489D01* -X146472589Y-108133989D01* -X146560194Y-108002879D01* -X146620537Y-107857197D01* -X146651300Y-107702542D01* -X146651300Y-107544858D01* -X146651300Y-107544855D01* -X146651299Y-107544853D01* -X146620538Y-107390210D01* -X146620537Y-107390203D01* -X146594465Y-107327258D01* -X146560197Y-107244527D01* -X146560190Y-107244514D01* -X146472589Y-107113411D01* -X146472586Y-107113407D01* -X146361092Y-107001913D01* -X146361088Y-107001910D01* -X146229985Y-106914309D01* -X146229972Y-106914302D01* -X146084301Y-106853964D01* -X146084289Y-106853961D01* -X145929645Y-106823200D01* -X145929642Y-106823200D01* -X145771958Y-106823200D01* -X145771955Y-106823200D01* -X145617310Y-106853961D01* -X145617298Y-106853964D01* -X145471627Y-106914302D01* -X145471614Y-106914309D01* -X145340511Y-107001910D01* -X145340507Y-107001913D01* -X145229013Y-107113407D01* -X145229010Y-107113411D01* -X145141409Y-107244514D01* -X145141402Y-107244527D01* -X145081064Y-107390198D01* -X145081061Y-107390210D01* -X145050300Y-107544853D01* -X135900160Y-107544853D01* -X135854145Y-107535700D01* -X135854142Y-107535700D01* -X135696458Y-107535700D01* -X135696455Y-107535700D01* -X135541810Y-107566461D01* -X135541798Y-107566464D01* -X135396127Y-107626802D01* -X135396114Y-107626809D01* -X135265011Y-107714410D01* -X135265007Y-107714413D01* -X135153513Y-107825907D01* -X135153510Y-107825911D01* -X135065909Y-107957014D01* -X135065902Y-107957027D01* -X135005564Y-108102698D01* -X135005561Y-108102710D01* -X134974800Y-108257353D01* -X120250500Y-108257353D01* -X120250500Y-107327253D01* -X123748700Y-107327253D01* -X123748700Y-107484946D01* -X123779461Y-107639589D01* -X123779464Y-107639601D01* -X123839802Y-107785272D01* -X123839809Y-107785285D01* -X123927410Y-107916388D01* -X123927413Y-107916392D01* -X124038907Y-108027886D01* -X124038911Y-108027889D01* -X124170014Y-108115490D01* -X124170027Y-108115497D01* -X124315698Y-108175835D01* -X124315703Y-108175837D01* -X124470353Y-108206599D01* -X124470356Y-108206600D01* -X124470358Y-108206600D01* -X124628044Y-108206600D01* -X124628045Y-108206599D01* -X124782697Y-108175837D01* -X124819919Y-108160418D01* -X124877172Y-108136705D01* -X124928372Y-108115497D01* -X124928372Y-108115496D01* -X124928379Y-108115494D01* -X125059489Y-108027889D01* -X125170989Y-107916389D01* -X125258594Y-107785279D01* -X125318937Y-107639597D01* -X125349700Y-107484942D01* -X125349700Y-107327258D01* -X125349700Y-107327255D01* -X125349699Y-107327253D01* -X125318937Y-107172603D01* -X125294419Y-107113411D01* -X125258597Y-107026927D01* -X125258590Y-107026914D01* -X125170989Y-106895811D01* -X125170986Y-106895807D01* -X125059492Y-106784313D01* -X125059488Y-106784310D01* -X124928385Y-106696709D01* -X124928372Y-106696702D01* -X124782701Y-106636364D01* -X124782689Y-106636361D01* -X124628045Y-106605600D01* -X124628042Y-106605600D01* -X124470358Y-106605600D01* -X124470355Y-106605600D01* -X124315710Y-106636361D01* -X124315698Y-106636364D01* -X124170027Y-106696702D01* -X124170014Y-106696709D01* -X124038911Y-106784310D01* -X124038907Y-106784313D01* -X123927413Y-106895807D01* -X123927410Y-106895811D01* -X123839809Y-107026914D01* -X123839802Y-107026927D01* -X123779464Y-107172598D01* -X123779461Y-107172610D01* -X123748700Y-107327253D01* -X120250500Y-107327253D01* -X120250500Y-104670153D01* -X124159100Y-104670153D01* -X124159100Y-104827846D01* -X124189861Y-104982489D01* -X124189864Y-104982501D01* -X124250202Y-105128172D01* -X124250209Y-105128185D01* -X124337810Y-105259288D01* -X124337813Y-105259292D01* -X124449307Y-105370786D01* -X124449311Y-105370789D01* -X124580414Y-105458390D01* -X124580427Y-105458397D01* -X124652826Y-105488385D01* -X124726103Y-105518737D01* -X124880753Y-105549499D01* -X124880756Y-105549500D01* -X124880758Y-105549500D01* -X125038444Y-105549500D01* -X125038445Y-105549499D01* -X125193097Y-105518737D01* -X125338779Y-105458394D01* -X125469889Y-105370789D01* -X125581389Y-105259289D01* -X125668994Y-105128179D01* -X125709515Y-105030353D01* -X130396700Y-105030353D01* -X130396700Y-105188046D01* -X130427461Y-105342689D01* -X130427464Y-105342701D01* -X130487802Y-105488372D01* -X130487809Y-105488385D01* -X130575410Y-105619488D01* -X130575413Y-105619492D01* -X130686907Y-105730986D01* -X130686911Y-105730989D01* -X130818014Y-105818590D01* -X130818027Y-105818597D01* -X130963698Y-105878935D01* -X130963703Y-105878937D01* -X131118353Y-105909699D01* -X131118356Y-105909700D01* -X131118358Y-105909700D01* -X131276044Y-105909700D01* -X131276045Y-105909699D01* -X131430697Y-105878937D01* -X131576379Y-105818594D01* -X131707489Y-105730989D01* -X131818989Y-105619489D01* -X131906594Y-105488379D01* -X131966937Y-105342697D01* -X131997700Y-105188042D01* -X131997700Y-105030358D01* -X131997700Y-105030355D01* -X131997699Y-105030353D01* -X131995587Y-105019735D01* -X131966937Y-104875703D01* -X131947114Y-104827846D01* -X131906597Y-104730027D01* -X131906590Y-104730014D01* -X131818989Y-104598911D01* -X131818986Y-104598907D01* -X131707492Y-104487413D01* -X131707488Y-104487410D01* -X131576385Y-104399809D01* -X131576372Y-104399802D01* -X131430701Y-104339464D01* -X131430689Y-104339461D01* -X131276045Y-104308700D01* -X131276042Y-104308700D01* -X131118358Y-104308700D01* -X131118355Y-104308700D01* -X130963710Y-104339461D01* -X130963698Y-104339464D01* -X130818027Y-104399802D01* -X130818014Y-104399809D01* -X130686911Y-104487410D01* -X130686907Y-104487413D01* -X130575413Y-104598907D01* -X130575410Y-104598911D01* -X130487809Y-104730014D01* -X130487802Y-104730027D01* -X130427464Y-104875698D01* -X130427461Y-104875710D01* -X130396700Y-105030353D01* -X125709515Y-105030353D01* -X125729337Y-104982497D01* -X125760100Y-104827842D01* -X125760100Y-104670158D01* -X125760100Y-104670155D01* -X125760099Y-104670153D01* -X125729338Y-104515510D01* -X125729337Y-104515503D01* -X125717701Y-104487410D01* -X125668997Y-104369827D01* -X125668990Y-104369814D01* -X125581390Y-104238712D01* -X125581386Y-104238707D01* -X125513832Y-104171153D01* -X135349500Y-104171153D01* -X135349500Y-104328846D01* -X135380261Y-104483489D01* -X135380264Y-104483501D01* -X135440602Y-104629172D01* -X135440609Y-104629185D01* -X135528210Y-104760288D01* -X135528213Y-104760292D01* -X135639707Y-104871786D01* -X135639711Y-104871789D01* -X135770814Y-104959390D01* -X135770827Y-104959397D01* -X135916498Y-105019735D01* -X135916503Y-105019737D01* -X136071153Y-105050499D01* -X136071156Y-105050500D01* -X136071158Y-105050500D01* -X136228844Y-105050500D01* -X136228845Y-105050499D01* -X136383497Y-105019737D01* -X136529179Y-104959394D01* -X136660289Y-104871789D01* -X136771789Y-104760289D01* -X136859394Y-104629179D01* -X136919737Y-104483497D01* -X136950500Y-104328842D01* -X136950500Y-104171158D01* -X136950500Y-104171155D01* -X136950499Y-104171153D01* -X136924333Y-104039609D01* -X136919737Y-104016503D01* -X136904311Y-103979261D01* -X136859397Y-103870827D01* -X136859390Y-103870814D01* -X136771789Y-103739711D01* -X136771786Y-103739707D01* -X136660292Y-103628213D01* -X136660288Y-103628210D01* -X136529185Y-103540609D01* -X136529172Y-103540602D01* -X136383501Y-103480264D01* -X136383489Y-103480261D01* -X136228845Y-103449500D01* -X136228842Y-103449500D01* -X136071158Y-103449500D01* -X136071155Y-103449500D01* -X135916510Y-103480261D01* -X135916498Y-103480264D01* -X135770827Y-103540602D01* -X135770814Y-103540609D01* -X135639711Y-103628210D01* -X135639707Y-103628213D01* -X135528213Y-103739707D01* -X135528210Y-103739711D01* -X135440609Y-103870814D01* -X135440602Y-103870827D01* -X135380264Y-104016498D01* -X135380261Y-104016510D01* -X135349500Y-104171153D01* -X125513832Y-104171153D01* -X125469892Y-104127213D01* -X125469888Y-104127210D01* -X125338785Y-104039609D01* -X125338772Y-104039602D01* -X125193101Y-103979264D01* -X125193089Y-103979261D01* -X125038445Y-103948500D01* -X125038442Y-103948500D01* -X124880758Y-103948500D01* -X124880755Y-103948500D01* -X124726110Y-103979261D01* -X124726098Y-103979264D01* -X124580427Y-104039602D01* -X124580414Y-104039609D01* -X124449311Y-104127210D01* -X124449307Y-104127213D01* -X124337813Y-104238707D01* -X124337810Y-104238711D01* -X124250209Y-104369814D01* -X124250202Y-104369827D01* -X124189864Y-104515498D01* -X124189861Y-104515510D01* -X124159100Y-104670153D01* -X120250500Y-104670153D01* +X120250500Y-120611152D01* +X129379498Y-120611152D01* +X129379498Y-120768845D01* +X129410259Y-120923488D01* +X129410262Y-120923500D01* +X129470600Y-121069171D01* +X129470607Y-121069184D01* +X129558208Y-121200287D01* +X129558211Y-121200291D01* +X129669705Y-121311785D01* +X129669709Y-121311788D01* +X129800812Y-121399389D01* +X129800825Y-121399396D01* +X129946496Y-121459734D01* +X129946501Y-121459736D01* +X130101151Y-121490498D01* +X130101154Y-121490499D01* +X130101156Y-121490499D01* +X130258842Y-121490499D01* +X130258843Y-121490498D01* +X130413495Y-121459736D01* +X130559177Y-121399393D01* +X130690287Y-121311788D01* +X130801787Y-121200288D01* +X130889392Y-121069178D01* +X130949735Y-120923496D01* +X130980498Y-120768841D01* +X130980498Y-120611157D01* +X130980498Y-120611154D01* +X130980497Y-120611152D01* +X130949736Y-120456509D01* +X130949735Y-120456502D01* +X130949733Y-120456497D01* +X130889395Y-120310826D01* +X130889388Y-120310813D01* +X130801787Y-120179710D01* +X130801784Y-120179706D01* +X130690290Y-120068212D01* +X130690286Y-120068209D01* +X130559183Y-119980608D01* +X130559170Y-119980601D01* +X130413499Y-119920263D01* +X130413487Y-119920260D01* +X130258843Y-119889499D01* +X130258840Y-119889499D01* +X130101156Y-119889499D01* +X130101153Y-119889499D01* +X129946508Y-119920260D01* +X129946496Y-119920263D01* +X129800825Y-119980601D01* +X129800812Y-119980608D01* +X129669709Y-120068209D01* +X129669705Y-120068212D01* +X129558211Y-120179706D01* +X129558208Y-120179710D01* +X129470607Y-120310813D01* +X129470600Y-120310826D01* +X129410262Y-120456497D01* +X129410259Y-120456509D01* +X129379498Y-120611152D01* +X120250500Y-120611152D01* +X120250500Y-119521153D01* +X123199500Y-119521153D01* +X123199500Y-119678846D01* +X123230261Y-119833489D01* +X123230264Y-119833501D01* +X123290602Y-119979172D01* +X123290609Y-119979185D01* +X123378210Y-120110288D01* +X123378213Y-120110292D01* +X123489707Y-120221786D01* +X123489711Y-120221789D01* +X123620814Y-120309390D01* +X123620827Y-120309397D01* +X123766498Y-120369735D01* +X123766503Y-120369737D01* +X123921153Y-120400499D01* +X123921156Y-120400500D01* +X123921158Y-120400500D01* +X124078844Y-120400500D01* +X124078845Y-120400499D01* +X124233497Y-120369737D01* +X124375722Y-120310826D01* +X124379172Y-120309397D01* +X124379172Y-120309396D01* +X124379179Y-120309394D01* +X124510289Y-120221789D01* +X124621789Y-120110289D01* +X124709394Y-119979179D01* +X124769737Y-119833497D01* +X124800500Y-119678842D01* +X124800500Y-119521158D01* +X124800500Y-119521155D01* +X124800499Y-119521153D01* +X124769738Y-119366510D01* +X124769737Y-119366503D01* +X124744284Y-119305053D01* +X124709397Y-119220827D01* +X124709390Y-119220814D01* +X124621789Y-119089711D01* +X124621786Y-119089707D01* +X124510292Y-118978213D01* +X124510288Y-118978210D01* +X124379185Y-118890609D01* +X124379172Y-118890602D01* +X124233501Y-118830264D01* +X124233489Y-118830261D01* +X124078845Y-118799500D01* +X124078842Y-118799500D01* +X123921158Y-118799500D01* +X123921155Y-118799500D01* +X123766510Y-118830261D01* +X123766498Y-118830264D01* +X123620827Y-118890602D01* +X123620814Y-118890609D01* +X123489711Y-118978210D01* +X123489707Y-118978213D01* +X123378213Y-119089707D01* +X123378210Y-119089711D01* +X123290609Y-119220814D01* +X123290602Y-119220827D01* +X123230264Y-119366498D01* +X123230261Y-119366510D01* +X123199500Y-119521153D01* +X120250500Y-119521153D01* +X120250500Y-117721153D01* +X126999500Y-117721153D01* +X126999500Y-117878846D01* +X127030261Y-118033489D01* +X127030264Y-118033501D01* +X127090602Y-118179172D01* +X127090609Y-118179185D01* +X127178210Y-118310288D01* +X127178213Y-118310292D01* +X127289707Y-118421786D01* +X127289711Y-118421789D01* +X127420814Y-118509390D01* +X127420827Y-118509397D01* +X127566498Y-118569735D01* +X127566503Y-118569737D01* +X127721153Y-118600499D01* +X127721156Y-118600500D01* +X127721158Y-118600500D01* +X127878844Y-118600500D01* +X127878845Y-118600499D01* +X128033497Y-118569737D01* +X128179179Y-118509394D01* +X128310289Y-118421789D01* +X128421789Y-118310289D01* +X128509394Y-118179179D01* +X128511331Y-118174504D01* +X128538301Y-118109390D01* +X128569737Y-118033497D01* +X128600500Y-117878842D01* +X128600500Y-117721158D01* +X128600500Y-117721155D01* +X128600499Y-117721153D01* +X128584287Y-117639649D01* +X128569737Y-117566503D01* +X128557901Y-117537927D01* +X128509397Y-117420827D01* +X128509390Y-117420814D01* +X128421789Y-117289711D01* +X128421786Y-117289707D01* +X128310292Y-117178213D01* +X128310288Y-117178210D01* +X128179185Y-117090609D01* +X128179172Y-117090602D01* +X128033501Y-117030264D01* +X128033489Y-117030261D01* +X127878845Y-116999500D01* +X127878842Y-116999500D01* +X127721158Y-116999500D01* +X127721155Y-116999500D01* +X127566510Y-117030261D01* +X127566498Y-117030264D01* +X127420827Y-117090602D01* +X127420814Y-117090609D01* +X127289711Y-117178210D01* +X127289707Y-117178213D01* +X127178213Y-117289707D01* +X127178210Y-117289711D01* +X127090609Y-117420814D01* +X127090602Y-117420827D01* +X127030264Y-117566498D01* +X127030261Y-117566510D01* +X126999500Y-117721153D01* +X120250500Y-117721153D01* +X120250500Y-116521153D01* +X129499500Y-116521153D01* +X129499500Y-116678846D01* +X129530261Y-116833489D01* +X129530264Y-116833501D01* +X129590604Y-116979176D01* +X129626162Y-117032392D01* +X129647040Y-117099069D01* +X129637623Y-117148732D01* +X129630262Y-117166502D01* +X129630261Y-117166505D01* +X129599500Y-117321153D01* +X129599500Y-117478846D01* +X129630261Y-117633489D01* +X129630264Y-117633501D01* +X129690602Y-117779172D01* +X129690609Y-117779185D01* +X129778210Y-117910288D01* +X129778213Y-117910292D01* +X129889707Y-118021786D01* +X129889711Y-118021789D01* +X130020814Y-118109390D01* +X130020827Y-118109397D01* +X130141028Y-118159185D01* +X130166503Y-118169737D01* +X130321153Y-118200499D01* +X130321156Y-118200500D01* +X130321158Y-118200500D01* +X130478844Y-118200500D01* +X130478845Y-118200499D01* +X130633497Y-118169737D01* +X130679457Y-118150699D01* +X130748924Y-118143230D01* +X130811403Y-118174504D01* +X130847057Y-118234592D01* +X130845697Y-118295669D01* +X130846587Y-118295846D01* +X130845581Y-118300900D01* +X130845574Y-118301240D01* +X130845399Y-118301814D01* +X130814636Y-118456471D01* +X130814636Y-118614164D01* +X130845397Y-118768807D01* +X130845400Y-118768819D01* +X130905738Y-118914490D01* +X130905745Y-118914503D01* +X130993346Y-119045606D01* +X130993349Y-119045610D01* +X131104843Y-119157104D01* +X131104847Y-119157107D01* +X131235950Y-119244708D01* +X131235963Y-119244715D01* +X131381634Y-119305053D01* +X131381639Y-119305055D01* +X131536289Y-119335817D01* +X131536292Y-119335818D01* +X131536294Y-119335818D01* +X131693980Y-119335818D01* +X131693981Y-119335817D01* +X131848633Y-119305055D01* +X131994315Y-119244712D01* +X132125425Y-119157107D01* +X132236925Y-119045607D01* +X132324530Y-118914497D01* +X132332591Y-118895034D01* +X132376431Y-118840631D01* +X132442725Y-118818565D01* +X132510425Y-118835843D01* +X132516039Y-118839381D01* +X132620821Y-118909394D01* +X132620823Y-118909395D01* +X132620827Y-118909397D01* +X132747998Y-118962072D01* +X132766503Y-118969737D01* +X132854426Y-118987226D01* +X132921153Y-119000499D01* +X132921156Y-119000500D01* +X132921158Y-119000500D01* +X133078844Y-119000500D01* +X133078845Y-119000499D01* +X133233497Y-118969737D01* +X133379179Y-118909394D01* +X133381110Y-118908103D01* +X133382276Y-118907737D01* +X133384546Y-118906525D01* +X133384776Y-118906955D01* +X133447786Y-118887226D01* +X133515166Y-118905710D01* +X133518850Y-118908077D01* +X133520821Y-118909394D01* +X133520824Y-118909395D01* +X133520827Y-118909397D01* +X133647998Y-118962072D01* +X133666503Y-118969737D01* +X133754426Y-118987226D01* +X133821153Y-119000499D01* +X133821156Y-119000500D01* +X133821158Y-119000500D01* +X133978844Y-119000500D01* +X133978845Y-119000499D01* +X134133497Y-118969737D01* +X134279179Y-118909394D01* +X134410289Y-118821789D01* +X134521789Y-118710289D01* +X134609394Y-118579179D01* +X134610277Y-118577048D01* +X134611035Y-118576106D01* +X134612264Y-118573809D01* +X134612699Y-118574041D01* +X134654115Y-118522646D01* +X134720408Y-118500579D01* +X134724838Y-118500500D01* +X134733741Y-118500500D01* +X134800780Y-118520185D01* +X134846535Y-118572989D01* +X134848302Y-118577048D01* +X134890602Y-118679172D01* +X134890609Y-118679185D01* +X134978210Y-118810288D01* +X134978213Y-118810292D01* +X135089707Y-118921786D01* +X135089711Y-118921789D01* +X135220814Y-119009390D01* +X135220827Y-119009397D01* +X135366498Y-119069735D01* +X135366503Y-119069737D01* +X135521153Y-119100499D01* +X135521156Y-119100500D01* +X135521158Y-119100500D01* +X135678844Y-119100500D01* +X135678845Y-119100499D01* +X135833497Y-119069737D01* +X135979179Y-119009394D01* +X135981110Y-119008103D01* +X135982276Y-119007737D01* +X135984546Y-119006525D01* +X135984776Y-119006955D01* +X136047786Y-118987226D01* +X136115166Y-119005710D01* +X136118850Y-119008077D01* +X136120821Y-119009394D01* +X136120824Y-119009395D01* +X136120827Y-119009397D01* +X136266498Y-119069735D01* +X136266503Y-119069737D01* +X136421153Y-119100499D01* +X136421156Y-119100500D01* +X136421158Y-119100500D01* +X136578844Y-119100500D01* +X136578845Y-119100499D01* +X136733497Y-119069737D01* +X136879179Y-119009394D01* +X137010289Y-118921789D01* +X137121789Y-118810289D01* +X137209394Y-118679179D01* +X137269737Y-118533497D01* +X137300500Y-118378842D01* +X137300500Y-118221158D01* +X137300500Y-118221155D01* +X137300499Y-118221153D01* +X137288173Y-118159185D01* +X137269737Y-118066503D01* +X137247783Y-118013501D01* +X137209397Y-117920827D01* +X137209390Y-117920814D01* +X137121789Y-117789711D01* +X137121786Y-117789707D01* +X137033232Y-117701153D01* +X144699500Y-117701153D01* +X144699500Y-117858846D01* +X144730261Y-118013489D01* +X144730264Y-118013501D01* +X144790602Y-118159172D01* +X144790609Y-118159185D01* +X144878210Y-118290288D01* +X144878213Y-118290292D01* +X144989707Y-118401786D01* +X144989711Y-118401789D01* +X145120814Y-118489390D01* +X145120827Y-118489397D01* +X145266498Y-118549735D01* +X145266503Y-118549737D01* +X145388687Y-118574041D01* +X145421153Y-118580499D01* +X145421156Y-118580500D01* +X145421158Y-118580500D01* +X145578844Y-118580500D01* +X145578845Y-118580499D01* +X145733497Y-118549737D01* +X145852367Y-118500500D01* +X145879172Y-118489397D01* +X145879172Y-118489396D01* +X145879179Y-118489394D01* +X146010289Y-118401789D01* +X146121789Y-118290289D01* +X146209394Y-118159179D01* +X146269737Y-118013497D01* +X146300500Y-117858842D01* +X146300500Y-117701158D01* +X146300500Y-117701155D01* +X146300499Y-117701153D01* +X146295936Y-117678213D01* +X146269737Y-117546503D01* +X146263010Y-117530263D01* +X146209397Y-117400827D01* +X146209390Y-117400814D01* +X146121789Y-117269711D01* +X146121786Y-117269707D01* +X146010292Y-117158213D01* +X146010288Y-117158210D01* +X145879185Y-117070609D01* +X145879172Y-117070602D01* +X145733501Y-117010264D01* +X145733489Y-117010261D01* +X145578845Y-116979500D01* +X145578842Y-116979500D01* +X145421158Y-116979500D01* +X145421155Y-116979500D01* +X145266510Y-117010261D01* +X145266498Y-117010264D01* +X145120827Y-117070602D01* +X145120814Y-117070609D01* +X144989711Y-117158210D01* +X144989707Y-117158213D01* +X144878213Y-117269707D01* +X144878210Y-117269711D01* +X144790609Y-117400814D01* +X144790602Y-117400827D01* +X144730264Y-117546498D01* +X144730261Y-117546510D01* +X144699500Y-117701153D01* +X137033232Y-117701153D01* +X137010292Y-117678213D01* +X137010288Y-117678210D01* +X136879185Y-117590609D01* +X136879172Y-117590602D01* +X136733501Y-117530264D01* +X136733489Y-117530261D01* +X136578845Y-117499500D01* +X136578842Y-117499500D01* +X136421158Y-117499500D01* +X136421155Y-117499500D01* +X136266510Y-117530261D01* +X136266498Y-117530264D01* +X136120822Y-117590604D01* +X136120820Y-117590605D01* +X136118885Y-117591899D01* +X136117717Y-117592264D01* +X136115451Y-117593476D01* +X136115221Y-117593045D01* +X136052206Y-117612773D01* +X135984827Y-117594285D01* +X135981115Y-117591899D01* +X135979179Y-117590605D01* +X135979177Y-117590604D01* +X135833501Y-117530264D01* +X135833489Y-117530261D01* +X135678845Y-117499500D01* +X135678842Y-117499500D01* +X135566259Y-117499500D01* +X135499220Y-117479815D01* +X135453465Y-117427011D01* +X135451698Y-117422952D01* +X135409397Y-117320827D01* +X135409390Y-117320814D01* +X135321789Y-117189711D01* +X135321786Y-117189707D01* +X135210292Y-117078213D01* +X135210288Y-117078210D01* +X135079185Y-116990609D01* +X135079172Y-116990602D01* +X134933501Y-116930264D01* +X134933489Y-116930261D01* +X134778845Y-116899500D01* +X134778842Y-116899500D01* +X134621158Y-116899500D01* +X134621155Y-116899500D01* +X134466510Y-116930261D01* +X134466498Y-116930264D01* +X134320827Y-116990602D01* +X134320814Y-116990609D01* +X134189711Y-117078210D01* +X134189707Y-117078213D01* +X134078213Y-117189707D01* +X134078210Y-117189711D01* +X133990609Y-117320814D01* +X133990607Y-117320819D01* +X133990606Y-117320821D01* +X133990467Y-117321158D01* +X133989725Y-117322949D01* +X133988964Y-117323893D01* +X133987736Y-117326191D01* +X133987300Y-117325958D01* +X133945885Y-117377354D01* +X133879592Y-117399421D01* +X133875162Y-117399500D01* +X133821155Y-117399500D01* +X133666510Y-117430261D01* +X133666498Y-117430264D01* +X133520822Y-117490604D01* +X133520820Y-117490605D01* +X133518885Y-117491899D01* +X133517717Y-117492264D01* +X133515451Y-117493476D01* +X133515221Y-117493045D01* +X133452206Y-117512773D01* +X133384827Y-117494285D01* +X133381115Y-117491899D01* +X133379179Y-117490605D01* +X133379177Y-117490604D01* +X133233501Y-117430264D01* +X133233489Y-117430261D01* +X133078845Y-117399500D01* +X133078842Y-117399500D01* +X132921158Y-117399500D01* +X132921155Y-117399500D01* +X132766510Y-117430261D01* +X132766498Y-117430264D01* +X132620827Y-117490602D01* +X132620814Y-117490609D01* +X132489711Y-117578210D01* +X132489707Y-117578213D01* +X132378213Y-117689707D01* +X132378210Y-117689711D01* +X132290609Y-117820814D01* +X132290606Y-117820820D01* +X132282542Y-117840288D01* +X132238699Y-117894690D01* +X132172404Y-117916752D01* +X132104705Y-117899471D01* +X132099091Y-117895933D01* +X131994321Y-117825927D01* +X131994308Y-117825920D01* +X131848637Y-117765582D01* +X131848625Y-117765579D01* +X131693981Y-117734818D01* +X131693978Y-117734818D01* +X131536294Y-117734818D01* +X131536291Y-117734818D01* +X131381646Y-117765579D01* +X131381634Y-117765582D01* +X131335678Y-117784618D01* +X131266208Y-117792087D01* +X131203730Y-117760811D01* +X131168078Y-117700722D01* +X131169442Y-117639649D01* +X131168549Y-117639472D01* +X131169559Y-117634392D01* +X131169567Y-117634055D01* +X131169731Y-117633511D01* +X131169737Y-117633497D01* +X131200500Y-117478842D01* +X131200500Y-117321158D01* +X131200500Y-117321155D01* +X131200499Y-117321153D01* +X131174353Y-117189711D01* +X131169737Y-117166503D01* +X131137014Y-117087502D01* +X131109397Y-117020827D01* +X131109395Y-117020823D01* +X131109394Y-117020821D01* +X131081346Y-116978844D01* +X131073837Y-116967606D01* +X131052959Y-116900929D01* +X131062377Y-116851264D01* +X131069737Y-116833497D01* +X131072192Y-116821153D01* +X138599500Y-116821153D01* +X138599500Y-116978846D01* +X138630261Y-117133489D01* +X138630264Y-117133501D01* +X138690602Y-117279172D01* +X138690609Y-117279185D01* +X138778210Y-117410288D01* +X138778213Y-117410292D01* +X138889707Y-117521786D01* +X138889711Y-117521789D01* +X139020814Y-117609390D01* +X139020827Y-117609397D01* +X139166498Y-117669735D01* +X139166503Y-117669737D01* +X139321153Y-117700499D01* +X139321156Y-117700500D01* +X139321158Y-117700500D01* +X139478844Y-117700500D01* +X139478845Y-117700499D01* +X139633497Y-117669737D01* +X139779179Y-117609394D01* +X139779186Y-117609388D01* +X139779190Y-117609387D01* +X139805262Y-117591966D01* +X139805266Y-117591964D01* +X139873309Y-117546498D01* +X139910289Y-117521789D01* +X140021789Y-117410289D01* +X140109394Y-117279179D01* +X140169737Y-117133497D01* +X140200500Y-116978842D01* +X140200500Y-116821158D01* +X140200500Y-116821155D01* +X140200499Y-116821153D01* +X140172192Y-116678846D01* +X140169737Y-116666503D01* +X140109534Y-116521158D01* +X140109397Y-116520827D01* +X140109390Y-116520814D01* +X140021789Y-116389711D01* +X140021786Y-116389707D01* +X139910292Y-116278213D01* +X139910288Y-116278210D01* +X139779185Y-116190609D01* +X139779172Y-116190602D01* +X139633501Y-116130264D01* +X139633489Y-116130261D01* +X139478845Y-116099500D01* +X139478842Y-116099500D01* +X139321158Y-116099500D01* +X139321155Y-116099500D01* +X139166510Y-116130261D01* +X139166498Y-116130264D01* +X139020827Y-116190602D01* +X139020814Y-116190609D01* +X138889711Y-116278210D01* +X138889707Y-116278213D01* +X138778213Y-116389707D01* +X138778210Y-116389711D01* +X138690609Y-116520814D01* +X138690602Y-116520827D01* +X138630264Y-116666498D01* +X138630261Y-116666510D01* +X138599500Y-116821153D01* +X131072192Y-116821153D01* +X131100500Y-116678842D01* +X131100500Y-116521158D01* +X131100500Y-116521155D01* +X131100499Y-116521153D01* +X131074353Y-116389711D01* +X131069737Y-116366503D01* +X131069735Y-116366498D01* +X131009397Y-116220827D01* +X131009390Y-116220814D01* +X130921789Y-116089711D01* +X130921786Y-116089707D01* +X130810292Y-115978213D01* +X130810288Y-115978210D01* +X130679185Y-115890609D01* +X130679172Y-115890602D01* +X130533501Y-115830264D01* +X130533489Y-115830261D01* +X130378845Y-115799500D01* +X130378842Y-115799500D01* +X130221158Y-115799500D01* +X130221155Y-115799500D01* +X130066510Y-115830261D01* +X130066498Y-115830264D01* +X129920827Y-115890602D01* +X129920814Y-115890609D01* +X129789711Y-115978210D01* +X129789707Y-115978213D01* +X129678213Y-116089707D01* +X129678210Y-116089711D01* +X129590609Y-116220814D01* +X129590602Y-116220827D01* +X129530264Y-116366498D01* +X129530261Y-116366510D01* +X129499500Y-116521153D01* +X120250500Y-116521153D01* +X120250500Y-114021153D01* +X121899500Y-114021153D01* +X121899500Y-114178846D01* +X121930261Y-114333489D01* +X121930264Y-114333501D01* +X121990602Y-114479172D01* +X121990609Y-114479185D01* +X122078210Y-114610288D01* +X122078213Y-114610292D01* +X122189707Y-114721786D01* +X122189711Y-114721789D01* +X122320814Y-114809390D01* +X122320827Y-114809397D01* +X122458683Y-114866498D01* +X122466503Y-114869737D01* +X122621153Y-114900499D01* +X122621156Y-114900500D01* +X122621158Y-114900500D01* +X122778844Y-114900500D01* +X122778845Y-114900499D01* +X122933497Y-114869737D01* +X123079179Y-114809394D01* +X123210289Y-114721789D01* +X123321789Y-114610289D01* +X123409394Y-114479179D01* +X123469737Y-114333497D01* +X123500500Y-114178842D01* +X123500500Y-114121153D01* +X129699500Y-114121153D01* +X129699500Y-114278846D01* +X129730261Y-114433489D01* +X129730264Y-114433501D01* +X129790602Y-114579172D01* +X129790609Y-114579185D01* +X129878210Y-114710288D01* +X129878213Y-114710292D01* +X129989707Y-114821786D01* +X129989711Y-114821789D01* +X130120814Y-114909390D01* +X130120827Y-114909397D01* +X130266498Y-114969735D01* +X130266503Y-114969737D01* +X130396982Y-114995691D01* +X130421153Y-115000499D01* +X130421156Y-115000500D01* +X130421158Y-115000500D01* +X130578844Y-115000500D01* +X130578845Y-115000499D01* +X130733497Y-114969737D01* +X130733509Y-114969731D01* +X130739324Y-114967969D01* +X130740158Y-114970720D01* +X130797359Y-114964497D01* +X130859878Y-114995691D01* +X130895608Y-115055734D01* +X130899500Y-115086555D01* +X130899500Y-115178846D01* +X130930261Y-115333489D01* +X130930264Y-115333501D01* +X130990602Y-115479172D01* +X130990609Y-115479185D01* +X131078210Y-115610288D01* +X131078213Y-115610292D01* +X131189707Y-115721786D01* +X131189711Y-115721789D01* +X131320814Y-115809390D01* +X131320827Y-115809397D01* +X131466498Y-115869735D01* +X131466503Y-115869737D01* +X131621153Y-115900499D01* +X131621156Y-115900500D01* +X131621158Y-115900500D01* +X131778844Y-115900500D01* +X131778845Y-115900499D01* +X131933497Y-115869737D01* +X132079179Y-115809394D01* +X132210289Y-115721789D01* +X132321789Y-115610289D01* +X132409394Y-115479179D01* +X132469737Y-115333497D01* +X132500500Y-115178842D01* +X132500500Y-115021158D01* +X132500500Y-115021155D01* +X132500499Y-115021153D01* +X132478269Y-114909397D01* +X132469737Y-114866503D01* +X132409794Y-114721786D01* +X132409397Y-114720827D01* +X132409390Y-114720814D01* +X132321789Y-114589711D01* +X132321786Y-114589707D01* +X132210292Y-114478213D01* +X132210288Y-114478210D01* +X132079185Y-114390609D01* +X132079172Y-114390602D01* +X131933501Y-114330264D01* +X131933489Y-114330261D01* +X131778845Y-114299500D01* +X131778842Y-114299500D01* +X131621158Y-114299500D01* +X131621155Y-114299500D01* +X131466510Y-114330261D01* +X131460676Y-114332031D01* +X131459873Y-114329385D01* +X131402056Y-114335396D01* +X131339687Y-114303902D01* +X131304245Y-114243689D01* +X131300500Y-114213444D01* +X131300500Y-114121155D01* +X131300499Y-114121153D01* +X131269737Y-113966503D01* +X131228314Y-113866498D01* +X131209397Y-113820827D01* +X131209390Y-113820814D01* +X131121789Y-113689711D01* +X131121786Y-113689707D01* +X131010292Y-113578213D01* +X131010288Y-113578210D01* +X130879185Y-113490609D01* +X130879172Y-113490602D01* +X130733501Y-113430264D01* +X130733489Y-113430261D01* +X130578845Y-113399500D01* +X130578842Y-113399500D01* +X130421158Y-113399500D01* +X130421155Y-113399500D01* +X130266510Y-113430261D01* +X130266498Y-113430264D01* +X130120827Y-113490602D01* +X130120814Y-113490609D01* +X129989711Y-113578210D01* +X129989707Y-113578213D01* +X129878213Y-113689707D01* +X129878210Y-113689711D01* +X129790609Y-113820814D01* +X129790602Y-113820827D01* +X129730264Y-113966498D01* +X129730261Y-113966510D01* +X129699500Y-114121153D01* +X123500500Y-114121153D01* +X123500500Y-114021158D01* +X123500500Y-114021155D01* +X123500499Y-114021153D01* +X123469738Y-113866510D01* +X123469737Y-113866503D01* +X123450812Y-113820814D01* +X123409397Y-113720827D01* +X123409390Y-113720814D01* +X123321789Y-113589711D01* +X123321786Y-113589707D01* +X123210292Y-113478213D01* +X123210288Y-113478210D01* +X123079185Y-113390609D01* +X123079172Y-113390602D01* +X122933501Y-113330264D01* +X122933489Y-113330261D01* +X122778845Y-113299500D01* +X122778842Y-113299500D01* +X122621158Y-113299500D01* +X122621155Y-113299500D01* +X122466510Y-113330261D01* +X122466498Y-113330264D01* +X122320827Y-113390602D01* +X122320814Y-113390609D01* +X122189711Y-113478210D01* +X122189707Y-113478213D01* +X122078213Y-113589707D01* +X122078210Y-113589711D01* +X121990609Y-113720814D01* +X121990602Y-113720827D01* +X121930264Y-113866498D01* +X121930261Y-113866510D01* +X121899500Y-114021153D01* +X120250500Y-114021153D01* +X120250500Y-111521153D01* +X123399500Y-111521153D01* +X123399500Y-111678846D01* +X123430261Y-111833489D01* +X123430264Y-111833501D01* +X123490602Y-111979172D01* +X123490609Y-111979185D01* +X123578210Y-112110288D01* +X123578213Y-112110292D01* +X123689707Y-112221786D01* +X123689711Y-112221789D01* +X123820814Y-112309390D01* +X123820827Y-112309397D01* +X123966498Y-112369735D01* +X123966503Y-112369737D01* +X124121153Y-112400499D01* +X124121156Y-112400500D01* +X124121158Y-112400500D01* +X124278844Y-112400500D01* +X124278845Y-112400499D01* +X124433497Y-112369737D01* +X124579179Y-112309394D01* +X124710289Y-112221789D01* +X124821789Y-112110289D01* +X124909394Y-111979179D01* +X124969737Y-111833497D01* +X125000500Y-111678842D01* +X125000500Y-111521158D01* +X125000500Y-111521155D01* +X125000499Y-111521153D01* +X124980734Y-111421789D01* +X124969737Y-111366503D01* +X124946452Y-111310288D01* +X124909397Y-111220827D01* +X124909390Y-111220814D01* +X124821789Y-111089711D01* +X124821786Y-111089707D01* +X124710292Y-110978213D01* +X124710288Y-110978210D01* +X124579185Y-110890609D01* +X124579172Y-110890602D01* +X124458154Y-110840475D01* +X124458147Y-110840473D01* +X124433497Y-110830263D01* +X124278842Y-110799500D01* +X124121158Y-110799500D01* +X124121155Y-110799500D01* +X123966510Y-110830261D01* +X123966498Y-110830264D01* +X123820827Y-110890602D01* +X123820814Y-110890609D01* +X123689711Y-110978210D01* +X123689707Y-110978213D01* +X123578213Y-111089707D01* +X123578210Y-111089711D01* +X123490609Y-111220814D01* +X123490602Y-111220827D01* +X123430264Y-111366498D01* +X123430261Y-111366510D01* +X123399500Y-111521153D01* +X120250500Y-111521153D01* +X120250500Y-109721153D01* +X123799500Y-109721153D01* +X123799500Y-109878846D01* +X123830261Y-110033489D01* +X123830264Y-110033501D01* +X123890602Y-110179172D01* +X123890609Y-110179185D01* +X123978210Y-110310288D01* +X123978213Y-110310292D01* +X124089707Y-110421786D01* +X124089711Y-110421789D01* +X124220814Y-110509390D01* +X124220827Y-110509397D01* +X124341844Y-110559523D01* +X124366503Y-110569737D01* +X124521158Y-110600500D01* +X124521249Y-110600500D01* +X124678844Y-110600500D01* +X124678845Y-110600499D01* +X124833497Y-110569737D01* +X124979179Y-110509394D01* +X125110289Y-110421789D01* +X125170144Y-110361933D01* +X125231463Y-110328450D01* +X125301155Y-110333434D01* +X125326714Y-110346514D01* +X125420814Y-110409390D01* +X125420827Y-110409397D01* +X125566498Y-110469735D01* +X125566503Y-110469737D01* +X125721153Y-110500499D01* +X125721156Y-110500500D01* +X125721158Y-110500500D01* +X125878844Y-110500500D01* +X125878845Y-110500499D01* +X126033497Y-110469737D01* +X126151592Y-110420821D01* +X126179172Y-110409397D01* +X126179172Y-110409396D01* +X126179179Y-110409394D01* +X126310289Y-110321789D01* +X126421789Y-110210289D01* +X126509394Y-110079179D01* +X126569737Y-109933497D01* +X126592083Y-109821158D01* +X126592084Y-109821153D01* +X129599500Y-109821153D01* +X129599500Y-109978846D01* +X129630261Y-110133489D01* +X129630264Y-110133501D01* +X129690602Y-110279172D01* +X129690612Y-110279190D01* +X129751732Y-110370663D01* +X129772610Y-110437340D01* +X129763192Y-110487004D01* +X129730262Y-110566506D01* +X129730260Y-110566511D01* +X129699500Y-110721153D01* +X129699500Y-110878846D01* +X129730261Y-111033489D01* +X129730264Y-111033501D01* +X129790602Y-111179172D01* +X129790609Y-111179185D01* +X129878210Y-111310288D01* +X129878213Y-111310292D01* +X129989707Y-111421786D01* +X129989711Y-111421789D01* +X130120814Y-111509390D01* +X130120827Y-111509397D01* +X130266498Y-111569735D01* +X130266503Y-111569737D01* +X130421153Y-111600499D01* +X130421156Y-111600500D01* +X130421158Y-111600500D01* +X130578844Y-111600500D01* +X130578845Y-111600499D01* +X130733497Y-111569737D01* +X130879179Y-111509394D01* +X131010289Y-111421789D01* +X131121789Y-111310289D01* +X131209394Y-111179179D01* +X131269737Y-111033497D01* +X131300500Y-110878842D01* +X131300500Y-110721158D01* +X131300500Y-110721155D01* +X131300499Y-110721153D01* +X131270380Y-110569735D01* +X131269737Y-110566503D01* +X131242398Y-110500500D01* +X131209397Y-110420827D01* +X131209390Y-110420814D01* +X131148267Y-110329337D01* +X131127389Y-110262659D01* +X131136808Y-110212993D01* +X131137928Y-110210289D01* +X131169737Y-110133497D01* +X131200500Y-109978842D01* +X131200500Y-109821158D01* +X131200500Y-109821155D01* +X131176982Y-109702925D01* +X131183209Y-109633333D01* +X131226072Y-109578156D01* +X131229675Y-109575653D01* +X131310289Y-109521789D01* +X131421789Y-109410289D01* +X131509394Y-109279179D01* +X131533429Y-109221153D01* +X146499500Y-109221153D01* +X146499500Y-109378846D01* +X146530261Y-109533489D01* +X146530264Y-109533501D01* +X146590602Y-109679172D01* +X146590609Y-109679185D01* +X146678210Y-109810288D01* +X146678213Y-109810292D01* +X146789707Y-109921786D01* +X146789711Y-109921789D01* +X146920814Y-110009390D01* +X146920827Y-110009397D01* +X147066498Y-110069735D01* +X147066503Y-110069737D01* +X147221153Y-110100499D01* +X147221156Y-110100500D01* +X147221158Y-110100500D01* +X147378844Y-110100500D01* +X147378845Y-110100499D01* +X147533497Y-110069737D01* +X147679179Y-110009394D01* +X147810289Y-109921789D01* +X147921789Y-109810289D01* +X148009394Y-109679179D01* +X148069737Y-109533497D01* +X148100500Y-109378842D01* +X148100500Y-109221158D01* +X148100500Y-109221155D01* +X148100499Y-109221153D01* +X148074531Y-109090606D01* +X148069737Y-109066503D01* +X148069735Y-109066498D01* +X148009397Y-108920827D01* +X148009390Y-108920814D01* +X147921789Y-108789711D01* +X147921786Y-108789707D01* +X147810292Y-108678213D01* +X147810288Y-108678210D01* +X147679185Y-108590609D01* +X147679172Y-108590602D01* +X147533501Y-108530264D01* +X147533489Y-108530261D01* +X147378845Y-108499500D01* +X147378842Y-108499500D01* +X147221158Y-108499500D01* +X147221155Y-108499500D01* +X147066510Y-108530261D01* +X147066498Y-108530264D01* +X146920827Y-108590602D01* +X146920814Y-108590609D01* +X146789711Y-108678210D01* +X146789707Y-108678213D01* +X146678213Y-108789707D01* +X146678210Y-108789711D01* +X146590609Y-108920814D01* +X146590602Y-108920827D01* +X146530264Y-109066498D01* +X146530261Y-109066510D01* +X146499500Y-109221153D01* +X131533429Y-109221153D01* +X131569737Y-109133497D01* +X131600500Y-108978842D01* +X131600500Y-108821158D01* +X131600500Y-108821155D01* +X131600499Y-108821153D01* +X131594244Y-108789707D01* +X131569737Y-108666503D01* +X131527049Y-108563446D01* +X131519581Y-108493978D01* +X131532264Y-108457521D01* +X131533649Y-108454928D01* +X131533659Y-108454914D01* +X131594002Y-108309232D01* +X131611522Y-108221153D01* +X144099500Y-108221153D01* +X144099500Y-108378846D01* +X144130261Y-108533489D01* +X144130264Y-108533501D01* +X144190602Y-108679172D01* +X144190609Y-108679185D01* +X144278210Y-108810288D01* +X144278213Y-108810292D01* +X144389707Y-108921786D01* +X144389711Y-108921789D01* +X144520814Y-109009390D01* +X144520827Y-109009397D01* +X144658683Y-109066498D01* +X144666503Y-109069737D01* +X144821153Y-109100499D01* +X144821156Y-109100500D01* +X144821158Y-109100500D01* +X144978844Y-109100500D01* +X144978845Y-109100499D01* +X144996061Y-109097075D01* +X145014287Y-109093450D01* +X145014292Y-109093449D01* +X145099800Y-109076439D01* +X145133497Y-109069737D01* +X145279179Y-109009394D01* +X145410289Y-108921789D01* +X145521789Y-108810289D01* +X145609394Y-108679179D01* +X145669737Y-108533497D01* +X145700500Y-108378842D01* +X145700500Y-108378835D01* +X145701097Y-108372782D01* +X145703484Y-108373017D01* +X145720185Y-108316141D01* +X145755606Y-108280080D01* +X145821888Y-108235793D01* +X145933388Y-108124293D01* +X146020993Y-107993183D01* +X146081336Y-107847501D01* +X146112099Y-107692846D01* +X146112099Y-107535162D01* +X146112099Y-107535159D01* +X146112098Y-107535157D01* +X146095944Y-107453945D01* +X146081336Y-107380507D01* +X146075467Y-107366337D01* +X146020996Y-107234831D01* +X146020989Y-107234818D01* +X145933388Y-107103715D01* +X145933385Y-107103711D01* +X145821891Y-106992217D01* +X145821887Y-106992214D01* +X145690784Y-106904613D01* +X145690771Y-106904606D01* +X145545100Y-106844268D01* +X145545088Y-106844265D01* +X145390444Y-106813504D01* +X145390441Y-106813504D01* +X145232757Y-106813504D01* +X145232754Y-106813504D01* +X145078109Y-106844265D01* +X145078097Y-106844268D01* +X144932426Y-106904606D01* +X144932413Y-106904613D01* +X144801310Y-106992214D01* +X144801306Y-106992217D01* +X144689812Y-107103711D01* +X144689809Y-107103715D01* +X144602208Y-107234818D01* +X144602201Y-107234831D01* +X144541863Y-107380502D01* +X144541860Y-107380514D01* +X144511099Y-107535157D01* +X144510502Y-107541222D01* +X144508114Y-107540986D01* +X144491414Y-107597861D01* +X144455990Y-107633924D01* +X144389711Y-107678210D01* +X144389707Y-107678213D01* +X144278213Y-107789707D01* +X144278210Y-107789711D01* +X144190609Y-107920814D01* +X144190602Y-107920827D01* +X144130264Y-108066498D01* +X144130261Y-108066510D01* +X144099500Y-108221153D01* +X131611522Y-108221153D01* +X131624765Y-108154577D01* +X131624765Y-107996893D01* +X131624765Y-107996890D01* +X131624764Y-107996888D01* +X131598308Y-107863886D01* +X131594002Y-107842238D01* +X131580770Y-107810292D01* +X131533662Y-107696562D01* +X131533655Y-107696549D01* +X131446054Y-107565446D01* +X131446051Y-107565442D01* +X131334557Y-107453948D01* +X131334553Y-107453945D01* +X131203450Y-107366344D01* +X131203437Y-107366337D01* +X131057766Y-107305999D01* +X131057754Y-107305996D01* +X130903110Y-107275235D01* +X130903107Y-107275235D01* +X130745423Y-107275235D01* +X130745420Y-107275235D01* +X130590775Y-107305996D01* +X130590763Y-107305999D01* +X130445092Y-107366337D01* +X130445079Y-107366344D01* +X130313976Y-107453945D01* +X130313972Y-107453948D01* +X130202478Y-107565442D01* +X130202475Y-107565446D01* +X130114874Y-107696549D01* +X130114867Y-107696562D01* +X130054529Y-107842233D01* +X130054526Y-107842245D01* +X130023765Y-107996888D01* +X130023765Y-108154581D01* +X130054526Y-108309224D01* +X130054529Y-108309236D01* +X130097213Y-108412286D01* +X130104682Y-108481756D01* +X130092020Y-108518173D01* +X130090608Y-108520815D01* +X130030264Y-108666498D01* +X130030261Y-108666510D01* +X129999500Y-108821153D01* +X129999500Y-108978846D01* +X130023017Y-109097075D01* +X130016790Y-109166667D01* +X129973927Y-109221844D01* +X129970291Y-109224368D01* +X129889711Y-109278210D01* +X129889707Y-109278213D01* +X129778213Y-109389707D01* +X129778210Y-109389711D01* +X129690609Y-109520814D01* +X129690602Y-109520827D01* +X129630264Y-109666498D01* +X129630261Y-109666510D01* +X129599500Y-109821153D01* +X126592084Y-109821153D01* +X126598107Y-109790875D01* +X126598107Y-109790874D01* +X126600500Y-109778844D01* +X126600500Y-109621155D01* +X126600499Y-109621153D01* +X126580734Y-109521789D01* +X126569737Y-109466503D01* +X126537929Y-109389711D01* +X126509397Y-109320827D01* +X126509390Y-109320814D01* +X126421789Y-109189711D01* +X126421786Y-109189707D01* +X126310292Y-109078213D01* +X126310288Y-109078210D01* +X126179185Y-108990609D01* +X126179172Y-108990602D01* +X126033501Y-108930264D01* +X126033489Y-108930261D01* +X125878845Y-108899500D01* +X125878842Y-108899500D01* +X125721158Y-108899500D01* +X125721155Y-108899500D01* +X125566510Y-108930261D01* +X125566498Y-108930264D01* +X125420827Y-108990602D01* +X125420814Y-108990609D01* +X125289711Y-109078210D01* +X125289707Y-109078213D01* +X125229857Y-109138064D01* +X125168534Y-109171549D01* +X125098842Y-109166565D01* +X125073285Y-109153485D01* +X124979185Y-109090609D01* +X124979172Y-109090602D01* +X124833501Y-109030264D01* +X124833489Y-109030261D01* +X124678845Y-108999500D01* +X124678842Y-108999500D01* +X124521158Y-108999500D01* +X124521155Y-108999500D01* +X124366510Y-109030261D01* +X124366498Y-109030264D01* +X124220827Y-109090602D01* +X124220814Y-109090609D01* +X124089711Y-109178210D01* +X124089707Y-109178213D01* +X123978213Y-109289707D01* +X123978210Y-109289711D01* +X123890609Y-109420814D01* +X123890602Y-109420827D01* +X123830264Y-109566498D01* +X123830261Y-109566510D01* +X123799500Y-109721153D01* +X120250500Y-109721153D01* +X120250500Y-106984540D01* +X121073430Y-106984540D01* +X121073430Y-107142233D01* +X121104191Y-107296876D01* +X121104194Y-107296888D01* +X121164532Y-107442559D01* +X121164539Y-107442572D01* +X121252140Y-107573675D01* +X121252143Y-107573679D01* +X121363637Y-107685173D01* +X121363641Y-107685176D01* +X121494744Y-107772777D01* +X121494757Y-107772784D01* +X121585311Y-107810292D01* +X121640433Y-107833124D01* +X121795083Y-107863886D01* +X121795086Y-107863887D01* +X121795088Y-107863887D01* +X121952774Y-107863887D01* +X121952775Y-107863886D01* +X122107427Y-107833124D01* +X122253109Y-107772781D01* +X122384219Y-107685176D01* +X122495719Y-107573676D01* +X122583324Y-107442566D01* +X122643667Y-107296884D01* +X122674430Y-107142229D01* +X122674430Y-106984545D01* +X122674430Y-106984542D01* +X122674429Y-106984540D01* +X122661820Y-106921153D01* +X122643667Y-106829890D01* +X122598102Y-106719887D01* +X122590634Y-106650419D01* +X122601294Y-106619772D01* +X122600963Y-106619635D01* +X122655955Y-106486870D01* +X122663637Y-106468324D01* +X122692911Y-106321153D01* +X125519500Y-106321153D01* +X125519500Y-106478846D01* +X125550261Y-106633489D01* +X125550264Y-106633501D01* +X125610602Y-106779172D01* +X125610609Y-106779185D01* +X125698210Y-106910288D01* +X125698213Y-106910292D01* +X125809707Y-107021786D01* +X125809711Y-107021789D01* +X125940814Y-107109390D01* +X125940827Y-107109397D01* +X126086498Y-107169735D01* +X126086503Y-107169737D01* +X126220662Y-107196423D01* +X126241153Y-107200499D01* +X126241156Y-107200500D01* +X126241158Y-107200500D01* +X126398844Y-107200500D01* +X126398845Y-107200499D01* +X126553497Y-107169737D01* +X126699179Y-107109394D01* +X126830289Y-107021789D01* +X126930925Y-106921153D01* +X132299500Y-106921153D01* +X132299500Y-107078846D01* +X132330261Y-107233489D01* +X132330264Y-107233501D01* +X132390602Y-107379172D01* +X132390609Y-107379185D01* +X132478210Y-107510288D01* +X132478213Y-107510292D01* +X132589707Y-107621786D01* +X132589711Y-107621789D01* +X132720814Y-107709390D01* +X132720827Y-107709397D01* +X132866498Y-107769735D01* +X132866503Y-107769737D01* +X133021153Y-107800499D01* +X133021156Y-107800500D01* +X133021158Y-107800500D01* +X133178844Y-107800500D01* +X133178845Y-107800499D01* +X133333497Y-107769737D01* +X133479179Y-107709394D01* +X133610289Y-107621789D01* +X133721789Y-107510289D01* +X133809394Y-107379179D01* +X133862560Y-107250822D01* +X133906398Y-107196423D01* +X133972691Y-107174357D01* +X134001311Y-107176661D01* +X134121155Y-107200500D01* +X134121158Y-107200500D01* +X134278844Y-107200500D01* +X134278845Y-107200499D01* +X134433497Y-107169737D01* +X134579179Y-107109394D01* +X134710289Y-107021789D01* +X134821789Y-106910289D01* +X134909394Y-106779179D01* +X134969737Y-106633497D01* +X135000500Y-106478842D01* +X135000500Y-106321158D01* +X135000500Y-106321155D01* +X135000499Y-106321153D01* +X134994422Y-106290602D01* +X134969737Y-106166503D01* +X134968084Y-106162512D01* +X134950953Y-106121153D01* +X138099500Y-106121153D01* +X138099500Y-106278846D01* +X138130261Y-106433489D01* +X138130264Y-106433501D01* +X138190602Y-106579172D01* +X138190609Y-106579185D01* +X138278210Y-106710288D01* +X138278213Y-106710292D01* +X138389707Y-106821786D01* +X138389711Y-106821789D01* +X138520814Y-106909390D01* +X138520827Y-106909397D01* +X138656158Y-106965452D01* +X138666503Y-106969737D01* +X138779502Y-106992214D01* +X138821153Y-107000499D01* +X138821156Y-107000500D01* +X138821158Y-107000500D01* +X138978844Y-107000500D01* +X138978845Y-107000499D01* +X139133497Y-106969737D01* +X139201315Y-106941645D01* +X139270782Y-106934177D01* +X139333261Y-106965452D01* +X139336447Y-106968526D01* +X139389707Y-107021786D01* +X139389711Y-107021789D01* +X139520814Y-107109390D01* +X139520827Y-107109397D01* +X139666498Y-107169735D01* +X139666503Y-107169737D01* +X139800662Y-107196423D01* +X139821153Y-107200499D01* +X139821156Y-107200500D01* +X139821158Y-107200500D01* +X139978844Y-107200500D01* +X139978845Y-107200499D01* +X140133497Y-107169737D01* +X140279179Y-107109394D01* +X140410289Y-107021789D01* +X140428606Y-107003472D01* +X140489928Y-106969985D01* +X140559620Y-106974968D01* +X140615554Y-107016838D01* +X140619391Y-107022260D01* +X140678210Y-107110288D01* +X140678213Y-107110292D01* +X140789707Y-107221786D01* +X140789711Y-107221789D01* +X140920814Y-107309390D01* +X140920827Y-107309397D01* +X141030082Y-107354651D01* +X141066503Y-107369737D01* +X141121831Y-107380742D01* +X141183740Y-107413126D01* +X141218315Y-107473841D01* +X141219256Y-107478166D01* +X141230261Y-107533492D01* +X141230264Y-107533501D01* +X141290602Y-107679172D01* +X141290609Y-107679185D01* +X141378210Y-107810288D01* +X141378213Y-107810292D01* +X141489707Y-107921786D01* +X141489711Y-107921789D01* +X141620814Y-108009390D01* +X141620827Y-108009397D01* +X141758683Y-108066498D01* +X141766503Y-108069737D01* +X141921153Y-108100499D01* +X141921156Y-108100500D01* +X141921158Y-108100500D01* +X142078844Y-108100500D01* +X142078845Y-108100499D01* +X142089179Y-108098443D01* +X142114287Y-108093450D01* +X142114292Y-108093449D01* +X142199800Y-108076439D01* +X142233497Y-108069737D01* +X142379179Y-108009394D01* +X142510289Y-107921789D01* +X142621789Y-107810289D01* +X142709394Y-107679179D01* +X142769737Y-107533497D01* +X142800500Y-107378842D01* +X142800500Y-107221158D01* +X142800500Y-107221155D01* +X142800499Y-107221153D01* +X142778447Y-107110292D01* +X142769737Y-107066503D01* +X142742398Y-107000500D01* +X142709397Y-106920827D01* +X142709390Y-106920814D01* +X142621789Y-106789711D01* +X142621786Y-106789707D01* +X142510292Y-106678213D01* +X142510288Y-106678210D01* +X142379185Y-106590609D01* +X142379172Y-106590602D01* +X142233501Y-106530264D01* +X142233492Y-106530261D01* +X142178166Y-106519256D01* +X142116256Y-106486870D01* +X142081682Y-106426154D01* +X142080750Y-106421874D01* +X142069737Y-106366503D01* +X142047854Y-106313673D01* +X142009397Y-106220827D01* +X142009390Y-106220814D01* +X141921789Y-106089711D01* +X141921786Y-106089707D01* +X141810292Y-105978213D01* +X141810288Y-105978210D01* +X141679185Y-105890609D01* +X141679172Y-105890602D01* +X141533501Y-105830264D01* +X141533489Y-105830261D01* +X141378845Y-105799500D01* +X141378842Y-105799500D01* +X141221158Y-105799500D01* +X141221155Y-105799500D01* +X141066510Y-105830261D01* +X141066498Y-105830264D01* +X140920827Y-105890602D01* +X140920814Y-105890609D01* +X140789711Y-105978210D01* +X140789706Y-105978214D01* +X140771389Y-105996531D01* +X140710065Y-106030015D01* +X140640374Y-106025029D01* +X140584441Y-105983156D01* +X140580608Y-105977739D01* +X140521789Y-105889711D01* +X140521786Y-105889707D01* +X140410292Y-105778213D01* +X140410288Y-105778210D01* +X140279185Y-105690609D01* +X140279172Y-105690602D01* +X140133501Y-105630264D01* +X140133489Y-105630261D01* +X139978845Y-105599500D01* +X139978842Y-105599500D01* +X139821158Y-105599500D01* +X139821155Y-105599500D01* +X139666505Y-105630261D01* +X139666497Y-105630264D01* +X139598682Y-105658353D01* +X139529213Y-105665820D01* +X139466734Y-105634544D01* +X139463551Y-105631472D01* +X139410292Y-105578213D01* +X139410288Y-105578210D01* +X139279185Y-105490609D01* +X139279172Y-105490602D01* +X139133501Y-105430264D01* +X139133489Y-105430261D01* +X138978845Y-105399500D01* +X138978842Y-105399500D01* +X138821158Y-105399500D01* +X138821155Y-105399500D01* +X138666510Y-105430261D01* +X138666498Y-105430264D01* +X138520827Y-105490602D01* +X138520814Y-105490609D01* +X138389711Y-105578210D01* +X138389707Y-105578213D01* +X138278213Y-105689707D01* +X138278210Y-105689711D01* +X138190609Y-105820814D01* +X138190602Y-105820827D01* +X138130264Y-105966498D01* +X138130261Y-105966510D01* +X138099500Y-106121153D01* +X134950953Y-106121153D01* +X134909397Y-106020827D01* +X134909390Y-106020814D01* +X134821789Y-105889711D01* +X134821786Y-105889707D01* +X134710292Y-105778213D01* +X134710288Y-105778210D01* +X134579185Y-105690609D01* +X134579172Y-105690602D01* +X134433501Y-105630264D01* +X134433489Y-105630261D01* +X134278845Y-105599500D01* +X134278842Y-105599500D01* +X134121158Y-105599500D01* +X134121155Y-105599500D01* +X133966510Y-105630261D01* +X133966498Y-105630264D01* +X133820827Y-105690602D01* +X133820814Y-105690609D01* +X133689711Y-105778210D01* +X133689707Y-105778213D01* +X133578213Y-105889707D01* +X133578210Y-105889711D01* +X133490609Y-106020814D01* +X133490604Y-106020824D01* +X133437440Y-106149174D01* +X133393599Y-106203577D01* +X133327305Y-106225642D01* +X133298688Y-106223338D01* +X133178846Y-106199500D01* +X133178842Y-106199500D01* +X133021158Y-106199500D01* +X133021155Y-106199500D01* +X132866510Y-106230261D01* +X132866498Y-106230264D01* +X132720827Y-106290602D01* +X132720814Y-106290609D01* +X132589711Y-106378210D01* +X132589707Y-106378213D01* +X132478213Y-106489707D01* +X132478210Y-106489711D01* +X132390609Y-106620814D01* +X132390602Y-106620827D01* +X132330264Y-106766498D01* +X132330261Y-106766510D01* +X132299500Y-106921153D01* +X126930925Y-106921153D01* +X126941789Y-106910289D01* +X126995506Y-106829897D01* +X127029390Y-106779185D01* +X127029390Y-106779184D01* +X127029394Y-106779179D01* +X127089737Y-106633497D01* +X127120500Y-106478842D01* +X127120500Y-106321158D01* +X127120500Y-106321155D01* +X127120499Y-106321153D01* +X127114422Y-106290602D01* +X127089737Y-106166503D01* +X127088084Y-106162512D01* +X127029397Y-106020827D01* +X127029390Y-106020814D01* +X126941789Y-105889711D01* +X126941786Y-105889707D01* +X126830292Y-105778213D01* +X126830288Y-105778210D01* +X126699185Y-105690609D01* +X126699172Y-105690602D01* +X126553501Y-105630264D01* +X126553489Y-105630261D01* +X126398845Y-105599500D01* +X126398842Y-105599500D01* +X126241158Y-105599500D01* +X126241155Y-105599500D01* +X126086510Y-105630261D01* +X126086498Y-105630264D01* +X125940827Y-105690602D01* +X125940814Y-105690609D01* +X125809711Y-105778210D01* +X125809707Y-105778213D01* +X125698213Y-105889707D01* +X125698210Y-105889711D01* +X125610609Y-106020814D01* +X125610602Y-106020827D01* +X125550264Y-106166498D01* +X125550261Y-106166510D01* +X125519500Y-106321153D01* +X122692911Y-106321153D01* +X122694400Y-106313669D01* +X122694400Y-106155985D01* +X122694400Y-106155982D01* +X122694399Y-106155980D01* +X122681216Y-106089707D01* +X122663637Y-106001330D01* +X122654061Y-105978211D01* +X122603297Y-105855654D01* +X122603290Y-105855641D01* +X122515689Y-105724538D01* +X122515686Y-105724534D01* +X122404192Y-105613040D01* +X122404188Y-105613037D01* +X122273085Y-105525436D01* +X122273072Y-105525429D01* +X122162498Y-105479629D01* +X122127397Y-105465090D01* +X122127389Y-105465088D01* +X121972745Y-105434327D01* +X121972742Y-105434327D01* +X121815058Y-105434327D01* +X121815055Y-105434327D01* +X121660410Y-105465088D01* +X121660398Y-105465091D01* +X121514727Y-105525429D01* +X121514714Y-105525436D01* +X121383611Y-105613037D01* +X121383607Y-105613040D01* +X121272113Y-105724534D01* +X121272110Y-105724538D01* +X121184509Y-105855641D01* +X121184502Y-105855654D01* +X121124164Y-106001325D01* +X121124161Y-106001337D01* +X121093400Y-106155980D01* +X121093400Y-106313673D01* +X121124161Y-106468316D01* +X121124164Y-106468328D01* +X121169726Y-106578325D01* +X121177195Y-106647794D01* +X121166538Y-106678443D01* +X121166867Y-106678580D01* +X121104194Y-106829885D01* +X121104191Y-106829897D01* +X121073430Y-106984540D01* +X120250500Y-106984540D01* +X120250500Y-105371155D01* +X127399500Y-105371155D01* +X127399500Y-105528848D01* +X127430261Y-105683491D01* +X127430264Y-105683503D01* +X127490602Y-105829174D01* +X127490609Y-105829187D01* +X127578210Y-105960290D01* +X127578213Y-105960294D01* +X127689707Y-106071788D01* +X127689711Y-106071791D01* +X127820814Y-106159392D01* +X127820827Y-106159399D01* +X127917641Y-106199500D01* +X127966503Y-106219739D01* +X128121153Y-106250501D01* +X128121156Y-106250502D01* +X128121158Y-106250502D01* +X128278844Y-106250502D01* +X128278845Y-106250501D01* +X128433497Y-106219739D01* +X128562033Y-106166498D01* +X128579172Y-106159399D01* +X128579172Y-106159398D01* +X128579179Y-106159396D01* +X128710289Y-106071791D01* +X128821789Y-105960291D01* +X128909394Y-105829181D01* +X128969737Y-105683499D01* +X129000500Y-105528844D01* +X129000500Y-105371160D01* +X129000500Y-105371157D01* +X129000499Y-105371155D01* +X128969738Y-105216512D01* +X128969737Y-105216505D01* +X128969735Y-105216500D01* +X128909397Y-105070829D01* +X128909390Y-105070816D01* +X128821789Y-104939713D01* +X128821786Y-104939709D01* +X128710292Y-104828215D01* +X128710288Y-104828212D01* +X128579185Y-104740611D01* +X128579172Y-104740604D01* +X128433501Y-104680266D01* +X128433489Y-104680263D01* +X128278845Y-104649502D01* +X128278842Y-104649502D01* +X128121158Y-104649502D01* +X128121155Y-104649502D01* +X127966510Y-104680263D01* +X127966498Y-104680266D01* +X127820827Y-104740604D01* +X127820814Y-104740611D01* +X127689711Y-104828212D01* +X127689707Y-104828215D01* +X127578213Y-104939709D01* +X127578210Y-104939713D01* +X127490609Y-105070816D01* +X127490602Y-105070829D01* +X127430264Y-105216500D01* +X127430261Y-105216512D01* +X127399500Y-105371155D01* +X120250500Y-105371155D01* +X120250500Y-104044681D01* +X124149500Y-104044681D01* +X124149500Y-104202374D01* +X124180261Y-104357017D01* +X124180264Y-104357029D01* +X124240602Y-104502700D01* +X124240609Y-104502713D01* +X124328210Y-104633816D01* +X124328213Y-104633820D01* +X124439707Y-104745314D01* +X124439711Y-104745317D01* +X124570814Y-104832918D01* +X124570827Y-104832925D01* +X124716498Y-104893263D01* +X124716503Y-104893265D01* +X124871153Y-104924027D01* +X124871156Y-104924028D01* +X124871158Y-104924028D01* +X125028844Y-104924028D01* +X125028845Y-104924027D01* +X125183497Y-104893265D01* +X125329179Y-104832922D01* +X125460289Y-104745317D01* +X125571789Y-104633817D01* +X125659394Y-104502707D01* +X125719737Y-104357025D01* +X125750500Y-104202370D01* +X125750500Y-104098089D01* +X140267610Y-104098089D01* +X140267610Y-104255782D01* +X140298371Y-104410425D01* +X140298374Y-104410437D01* +X140358712Y-104556108D01* +X140358719Y-104556121D01* +X140446320Y-104687224D01* +X140446323Y-104687228D01* +X140557817Y-104798722D01* +X140557821Y-104798725D01* +X140688924Y-104886326D01* +X140688937Y-104886333D01* +X140817800Y-104939709D01* +X140834613Y-104946673D01* +X140989263Y-104977435D01* +X140989266Y-104977436D01* +X140989268Y-104977436D01* +X141146954Y-104977436D01* +X141146955Y-104977435D01* +X141301607Y-104946673D01* +X141447289Y-104886330D01* +X141578399Y-104798725D01* +X141689899Y-104687225D01* +X141777504Y-104556115D01* +X141837847Y-104410433D01* +X141868610Y-104255778D01* +X141868610Y-104098094D01* +X141868610Y-104098091D01* +X141868609Y-104098089D01* +X141837848Y-103943446D01* +X141837847Y-103943439D01* +X141815723Y-103890026D01* +X141777507Y-103797763D01* +X141777500Y-103797750D01* +X141689899Y-103666647D01* +X141689896Y-103666643D01* +X141578402Y-103555149D01* +X141578398Y-103555146D01* +X141447295Y-103467545D01* +X141447282Y-103467538D01* +X141301611Y-103407200D01* +X141301599Y-103407197D01* +X141146955Y-103376436D01* +X141146952Y-103376436D01* +X140989268Y-103376436D01* +X140989265Y-103376436D01* +X140834620Y-103407197D01* +X140834608Y-103407200D01* +X140688937Y-103467538D01* +X140688924Y-103467545D01* +X140557821Y-103555146D01* +X140557817Y-103555149D01* +X140446323Y-103666643D01* +X140446320Y-103666647D01* +X140358719Y-103797750D01* +X140358712Y-103797763D01* +X140298374Y-103943434D01* +X140298371Y-103943446D01* +X140267610Y-104098089D01* +X125750500Y-104098089D01* +X125750500Y-104044686D01* +X125750500Y-104044683D01* +X125750499Y-104044681D01* +X125730362Y-103943446D01* +X125719737Y-103890031D01* +X125681519Y-103797763D01* +X125659397Y-103744355D01* +X125659390Y-103744342D01* +X125571789Y-103613239D01* +X125571786Y-103613235D01* +X125460292Y-103501741D01* +X125460288Y-103501738D01* +X125329185Y-103414137D01* +X125329172Y-103414130D01* +X125183501Y-103353792D01* +X125183489Y-103353789D01* +X125028845Y-103323028D01* +X125028842Y-103323028D01* +X124871158Y-103323028D01* +X124871155Y-103323028D01* +X124716510Y-103353789D01* +X124716498Y-103353792D01* +X124570827Y-103414130D01* +X124570814Y-103414137D01* +X124439711Y-103501738D01* +X124439707Y-103501741D01* +X124328213Y-103613235D01* +X124328210Y-103613239D01* +X124240609Y-103744342D01* +X124240602Y-103744355D01* +X124180264Y-103890026D01* +X124180261Y-103890038D01* +X124149500Y-104044681D01* +X120250500Y-104044681D01* +X120250500Y-102721153D01* +X121499500Y-102721153D01* +X121499500Y-102878846D01* +X121530261Y-103033489D01* +X121530264Y-103033501D01* +X121590602Y-103179172D01* +X121590609Y-103179185D01* +X121678210Y-103310288D01* +X121678213Y-103310292D01* +X121789707Y-103421786D01* +X121789711Y-103421789D01* +X121920814Y-103509390D01* +X121920827Y-103509397D01* +X122031277Y-103555146D01* +X122066503Y-103569737D01* +X122221153Y-103600499D01* +X122221156Y-103600500D01* +X122221158Y-103600500D01* +X122378844Y-103600500D01* +X122378845Y-103600499D01* +X122533497Y-103569737D01* +X122679179Y-103509394D01* +X122810289Y-103421789D01* +X122921789Y-103310289D01* +X123009394Y-103179179D01* +X123069737Y-103033497D01* +X123100500Y-102878842D01* +X123100500Y-102721158D01* +X123100500Y-102721155D01* +X123100499Y-102721153D01* +X123069738Y-102566510D01* +X123069737Y-102566503D01* +X123033427Y-102478842D01* +X123009397Y-102420827D01* +X123009390Y-102420814D01* +X122984763Y-102383957D01* +X122942798Y-102321153D01* +X141799500Y-102321153D01* +X141799500Y-102478846D01* +X141830261Y-102633489D01* +X141830264Y-102633501D01* +X141890602Y-102779172D01* +X141890609Y-102779185D01* +X141978210Y-102910288D01* +X141978213Y-102910292D01* +X142089707Y-103021786D01* +X142089711Y-103021789D01* +X142220814Y-103109390D01* +X142220827Y-103109397D01* +X142366498Y-103169735D01* +X142366503Y-103169737D01* +X142521153Y-103200499D01* +X142521156Y-103200500D01* +X142521158Y-103200500D01* +X142678844Y-103200500D01* +X142678845Y-103200499D01* +X142833497Y-103169737D01* +X142979179Y-103109394D01* +X143110289Y-103021789D01* +X143221789Y-102910289D01* +X143309394Y-102779179D01* +X143369737Y-102633497D01* +X143400500Y-102478842D01* +X143400500Y-102321158D01* +X143400500Y-102321155D01* +X143400499Y-102321153D01* +X143372066Y-102178211D01* +X143369737Y-102166503D01* +X143338298Y-102090602D01* +X143309397Y-102020827D01* +X143309390Y-102020814D01* +X143221789Y-101889711D01* +X143221786Y-101889707D01* +X143110292Y-101778213D01* +X143110288Y-101778210D01* +X142979185Y-101690609D01* +X142979172Y-101690602D01* +X142833501Y-101630264D01* +X142833489Y-101630261D01* +X142678845Y-101599500D01* +X142678842Y-101599500D01* +X142521158Y-101599500D01* +X142521155Y-101599500D01* +X142366510Y-101630261D01* +X142366498Y-101630264D01* +X142220827Y-101690602D01* +X142220814Y-101690609D01* +X142089711Y-101778210D01* +X142089707Y-101778213D01* +X141978213Y-101889707D01* +X141978210Y-101889711D01* +X141890609Y-102020814D01* +X141890602Y-102020827D01* +X141830264Y-102166498D01* +X141830261Y-102166510D01* +X141799500Y-102321153D01* +X122942798Y-102321153D01* +X122921789Y-102289711D01* +X122921786Y-102289707D01* +X122810292Y-102178213D01* +X122810288Y-102178210D01* +X122679185Y-102090609D01* +X122679172Y-102090602D01* +X122533501Y-102030264D01* +X122533489Y-102030261D01* +X122378845Y-101999500D01* +X122378842Y-101999500D01* +X122221158Y-101999500D01* +X122221155Y-101999500D01* +X122066510Y-102030261D01* +X122066498Y-102030264D01* +X121920827Y-102090602D01* +X121920814Y-102090609D01* +X121789711Y-102178210D01* +X121789707Y-102178213D01* +X121678213Y-102289707D01* +X121678210Y-102289711D01* +X121590609Y-102420814D01* +X121590602Y-102420827D01* +X121530264Y-102566498D01* +X121530261Y-102566510D01* +X121499500Y-102721153D01* +X120250500Y-102721153D01* X120250500Y-100321153D01* -X125934800Y-100321153D01* -X125934800Y-100478846D01* -X125965561Y-100633489D01* -X125965564Y-100633501D01* -X126025902Y-100779172D01* -X126025909Y-100779185D01* -X126113510Y-100910288D01* -X126113513Y-100910292D01* -X126225007Y-101021786D01* -X126225011Y-101021789D01* -X126356114Y-101109390D01* -X126356127Y-101109397D01* -X126501798Y-101169735D01* -X126501803Y-101169737D01* -X126656453Y-101200499D01* -X126656456Y-101200500D01* -X126656458Y-101200500D01* -X126814144Y-101200500D01* -X126814145Y-101200499D01* -X126968797Y-101169737D01* -X127114479Y-101109394D01* -X127245589Y-101021789D01* -X127357089Y-100910289D01* -X127444694Y-100779179D01* -X127505037Y-100633497D01* -X127535800Y-100478842D01* -X127535800Y-100321158D01* -X127535800Y-100321155D01* -X127535799Y-100321153D01* -X127525558Y-100269669D01* -X127505037Y-100166503D01* -X127479752Y-100105458D01* -X127444697Y-100020827D01* -X127444690Y-100020814D01* -X127357089Y-99889711D01* -X127357086Y-99889707D01* -X127245592Y-99778213D01* -X127245588Y-99778210D01* -X127114485Y-99690609D01* -X127114472Y-99690602D01* -X126968801Y-99630264D01* -X126968789Y-99630261D01* -X126814145Y-99599500D01* -X126814142Y-99599500D01* -X126656458Y-99599500D01* -X126656455Y-99599500D01* -X126501810Y-99630261D01* -X126501798Y-99630264D01* -X126356127Y-99690602D01* -X126356114Y-99690609D01* -X126225011Y-99778210D01* -X126225007Y-99778213D01* -X126113513Y-99889707D01* -X126113510Y-99889711D01* -X126025909Y-100020814D01* -X126025902Y-100020827D01* -X125965564Y-100166498D01* -X125965561Y-100166510D01* -X125934800Y-100321153D01* +X125799500Y-100321153D01* +X125799500Y-100478846D01* +X125830261Y-100633489D01* +X125830264Y-100633501D01* +X125890602Y-100779172D01* +X125890609Y-100779185D01* +X125978210Y-100910288D01* +X125978213Y-100910292D01* +X126089707Y-101021786D01* +X126089711Y-101021789D01* +X126220814Y-101109390D01* +X126220827Y-101109397D01* +X126366498Y-101169735D01* +X126366503Y-101169737D01* +X126521153Y-101200499D01* +X126521156Y-101200500D01* +X126521158Y-101200500D01* +X126678844Y-101200500D01* +X126678845Y-101200499D01* +X126833497Y-101169737D01* +X126979179Y-101109394D01* +X127110289Y-101021789D01* +X127110925Y-101021153D01* +X130299500Y-101021153D01* +X130299500Y-101178846D01* +X130330261Y-101333489D01* +X130330264Y-101333501D01* +X130390602Y-101479172D01* +X130390609Y-101479185D01* +X130478210Y-101610288D01* +X130478213Y-101610292D01* +X130589707Y-101721786D01* +X130589711Y-101721789D01* +X130720814Y-101809390D01* +X130720827Y-101809397D01* +X130813129Y-101847629D01* +X130866503Y-101869737D01* +X131021153Y-101900499D01* +X131021156Y-101900500D01* +X131021158Y-101900500D01* +X131178844Y-101900500D01* +X131178845Y-101900499D01* +X131333497Y-101869737D01* +X131479179Y-101809394D01* +X131610289Y-101721789D01* +X131721789Y-101610289D01* +X131809394Y-101479179D01* +X131869737Y-101333497D01* +X131900500Y-101178842D01* +X131900500Y-101021158D01* +X131900500Y-101021155D01* +X131900499Y-101021153D01* +X131878447Y-100910292D01* +X131869737Y-100866503D01* +X131851215Y-100821786D01* +X131826666Y-100762518D01* +X131809532Y-100721153D01* +X132499500Y-100721153D01* +X132499500Y-100878846D01* +X132530261Y-101033489D01* +X132530264Y-101033501D01* +X132590602Y-101179172D01* +X132590609Y-101179185D01* +X132678210Y-101310288D01* +X132678213Y-101310292D01* +X132789707Y-101421786D01* +X132789711Y-101421789D01* +X132920814Y-101509390D01* +X132920827Y-101509397D01* +X133066498Y-101569735D01* +X133066503Y-101569737D01* +X133216131Y-101599500D01* +X133221153Y-101600499D01* +X133221156Y-101600500D01* +X133221158Y-101600500D01* +X133378844Y-101600500D01* +X133378845Y-101600499D01* +X133533497Y-101569737D01* +X133679179Y-101509394D01* +X133810289Y-101421789D01* +X133921789Y-101310289D01* +X134009394Y-101179179D01* +X134069737Y-101033497D01* +X134100500Y-100878842D01* +X134100500Y-100721158D01* +X134100500Y-100721155D01* +X134100499Y-100721153D01* +X134074353Y-100589711D01* +X134069737Y-100566503D01* +X134049003Y-100516446D01* +X134009397Y-100420827D01* +X134009390Y-100420814D01* +X133921789Y-100289711D01* +X133921786Y-100289707D01* +X133810292Y-100178213D01* +X133810288Y-100178210D01* +X133679185Y-100090609D01* +X133679172Y-100090602D01* +X133533501Y-100030264D01* +X133533489Y-100030261D01* +X133378845Y-99999500D01* +X133378842Y-99999500D01* +X133221158Y-99999500D01* +X133221155Y-99999500D01* +X133066510Y-100030261D01* +X133066498Y-100030264D01* +X132920827Y-100090602D01* +X132920814Y-100090609D01* +X132789711Y-100178210D01* +X132789707Y-100178213D01* +X132678213Y-100289707D01* +X132678210Y-100289711D01* +X132590609Y-100420814D01* +X132590602Y-100420827D01* +X132530264Y-100566498D01* +X132530261Y-100566510D01* +X132499500Y-100721153D01* +X131809532Y-100721153D01* +X131809395Y-100720823D01* +X131809390Y-100720814D01* +X131721789Y-100589711D01* +X131721786Y-100589707D01* +X131610292Y-100478213D01* +X131610288Y-100478210D01* +X131479185Y-100390609D01* +X131479172Y-100390602D01* +X131333501Y-100330264D01* +X131333489Y-100330261D01* +X131178845Y-100299500D01* +X131178842Y-100299500D01* +X131021158Y-100299500D01* +X131021155Y-100299500D01* +X130866510Y-100330261D01* +X130866498Y-100330264D01* +X130720827Y-100390602D01* +X130720814Y-100390609D01* +X130589711Y-100478210D01* +X130589707Y-100478213D01* +X130478213Y-100589707D01* +X130478210Y-100589711D01* +X130390609Y-100720814D01* +X130390602Y-100720827D01* +X130330264Y-100866498D01* +X130330261Y-100866510D01* +X130299500Y-101021153D01* +X127110925Y-101021153D01* +X127131579Y-101000499D01* +X127204694Y-100927385D01* +X127221786Y-100910292D01* +X127221789Y-100910289D01* +X127309394Y-100779179D01* +X127369737Y-100633497D01* +X127400500Y-100478842D01* +X127400500Y-100321158D01* +X127400500Y-100321155D01* +X127400499Y-100321153D01* +X127394244Y-100289707D01* +X127369737Y-100166503D01* +X127350955Y-100121158D01* +X127309397Y-100020827D01* +X127309393Y-100020820D01* +X127309389Y-100020814D01* +X127288800Y-99990000D01* +X127267923Y-99923324D01* +X127286407Y-99855944D01* +X127338386Y-99809253D01* +X127407356Y-99798077D01* +X127416084Y-99799490D01* +X127421158Y-99800500D01* +X127421160Y-99800500D01* +X127578844Y-99800500D01* +X127578845Y-99800499D01* +X127733497Y-99769737D01* +X127879179Y-99709394D01* +X128010289Y-99621789D01* +X128121789Y-99510289D01* +X128209394Y-99379179D01* +X128269737Y-99233497D01* +X128300500Y-99078842D01* +X128300500Y-98921158D01* +X128300500Y-98921155D01* +X128300499Y-98921153D01* +X135099500Y-98921153D01* +X135099500Y-99078846D01* +X135130261Y-99233489D01* +X135130264Y-99233501D01* +X135190602Y-99379172D01* +X135190609Y-99379184D01* +X135231570Y-99440486D01* +X135252448Y-99507163D01* +X135243809Y-99552726D01* +X135244053Y-99552801D01* +X135243365Y-99555068D01* +X135243033Y-99556820D01* +X135242287Y-99558620D01* +X135242283Y-99558632D01* +X135211523Y-99713274D01* +X135211523Y-99870967D01* +X135242284Y-100025610D01* +X135242287Y-100025622D01* +X135302625Y-100171293D01* +X135302632Y-100171306D01* +X135390233Y-100302409D01* +X135390236Y-100302413D01* +X135501730Y-100413907D01* +X135501736Y-100413912D01* +X135527333Y-100431016D01* +X135572138Y-100484629D01* +X135580844Y-100553954D01* +X135550688Y-100616981D01* +X135546126Y-100621794D01* +X135539980Y-100627939D01* +X135539975Y-100627946D01* +X135452374Y-100759049D01* +X135452367Y-100759062D01* +X135392029Y-100904733D01* +X135392026Y-100904745D01* +X135361265Y-101059388D01* +X135361265Y-101217081D01* +X135392026Y-101371724D01* +X135392029Y-101371736D01* +X135452367Y-101517407D01* +X135452374Y-101517420D01* +X135539975Y-101648523D01* +X135539978Y-101648527D01* +X135651472Y-101760021D01* +X135651476Y-101760024D01* +X135782579Y-101847625D01* +X135782592Y-101847632D01* +X135910226Y-101900499D01* +X135928268Y-101907972D01* +X136082918Y-101938734D01* +X136082921Y-101938735D01* +X136082923Y-101938735D01* +X136240609Y-101938735D01* +X136240610Y-101938734D01* +X136395262Y-101907972D01* +X136540944Y-101847629D01* +X136672054Y-101760024D01* +X136783554Y-101648524D01* +X136871159Y-101517414D01* +X136931502Y-101371732D01* +X136962265Y-101217077D01* +X136962265Y-101070718D01* +X136981950Y-101003679D01* +X137034754Y-100957924D01* +X137103912Y-100947980D01* +X137133717Y-100956157D01* +X137166498Y-100969735D01* +X137166503Y-100969737D01* +X137321153Y-101000499D01* +X137321156Y-101000500D01* +X137321158Y-101000500D01* +X137478844Y-101000500D01* +X137478845Y-101000499D01* +X137633497Y-100969737D01* +X137779179Y-100909394D01* +X137910289Y-100821789D01* +X138021789Y-100710289D01* +X138109394Y-100579179D01* +X138169737Y-100433497D01* +X138200500Y-100278842D01* +X138200500Y-100121158D01* +X138200500Y-100121155D01* +X138200499Y-100121153D01* +X138182419Y-100030261D01* +X138169737Y-99966503D01* +X138137929Y-99889711D01* +X138109397Y-99820827D01* +X138109390Y-99820814D01* +X138021789Y-99689711D01* +X138021786Y-99689707D01* +X137910292Y-99578213D01* +X137910288Y-99578210D01* +X137779185Y-99490609D01* +X137779172Y-99490602D01* +X137633501Y-99430264D01* +X137633489Y-99430261D01* +X137478845Y-99399500D01* +X137478842Y-99399500D01* +X137321158Y-99399500D01* +X137321155Y-99399500D01* +X137166510Y-99430261D01* +X137166498Y-99430264D01* +X137020827Y-99490602D01* +X137020814Y-99490609D01* +X136937146Y-99546515D01* +X136870468Y-99567393D01* +X136803088Y-99548908D01* +X136756398Y-99496929D01* +X136753694Y-99490865D01* +X136721419Y-99412946D01* +X136721418Y-99412945D01* +X136721417Y-99412942D01* +X136680451Y-99351633D01* +X136659574Y-99284958D01* +X136668216Y-99239403D01* +X136667968Y-99239328D01* +X136668668Y-99237019D01* +X136668998Y-99235280D01* +X136669737Y-99233497D01* +X136700500Y-99078842D01* +X136700500Y-98921158D01* +X136700500Y-98921155D01* +X136700499Y-98921153D01* +X136689455Y-98865633D01* +X136669737Y-98766503D01* +X136628328Y-98666531D01* +X136609397Y-98620827D01* +X136609390Y-98620814D01* +X136521789Y-98489711D01* +X136521786Y-98489707D01* +X136410292Y-98378213D01* +X136410288Y-98378210D01* +X136279185Y-98290609D01* +X136279172Y-98290602D01* +X136192630Y-98254756D01* +X136133501Y-98230264D01* +X136133489Y-98230261D01* +X135978845Y-98199500D01* +X135978842Y-98199500D01* +X135821158Y-98199500D01* +X135821155Y-98199500D01* +X135666510Y-98230261D01* +X135666498Y-98230264D01* +X135520827Y-98290602D01* +X135520814Y-98290609D01* +X135389711Y-98378210D01* +X135389707Y-98378213D01* +X135278213Y-98489707D01* +X135278210Y-98489711D01* +X135190609Y-98620814D01* +X135190602Y-98620827D01* +X135130264Y-98766498D01* +X135130261Y-98766510D01* +X135099500Y-98921153D01* +X128300499Y-98921153D01* +X128289455Y-98865633D01* +X128269737Y-98766503D01* +X128228328Y-98666531D01* +X128209397Y-98620827D01* +X128209390Y-98620814D01* +X128121789Y-98489711D01* +X128121786Y-98489707D01* +X128010292Y-98378213D01* +X128010288Y-98378210D01* +X127879185Y-98290609D01* +X127879172Y-98290602D01* +X127733501Y-98230264D01* +X127733489Y-98230261D01* +X127578845Y-98199500D01* +X127578842Y-98199500D01* +X127421158Y-98199500D01* +X127421155Y-98199500D01* +X127266510Y-98230261D01* +X127266498Y-98230264D01* +X127120827Y-98290602D01* +X127120814Y-98290609D01* +X126989711Y-98378210D01* +X126989707Y-98378213D01* +X126878213Y-98489707D01* +X126878210Y-98489711D01* +X126790609Y-98620814D01* +X126790602Y-98620827D01* +X126730264Y-98766498D01* +X126730261Y-98766510D01* +X126699500Y-98921153D01* +X126699500Y-99078846D01* +X126730261Y-99233489D01* +X126730264Y-99233501D01* +X126790602Y-99379172D01* +X126790609Y-99379185D01* +X126811198Y-99409998D01* +X126832076Y-99476676D01* +X126813592Y-99544056D01* +X126761613Y-99590746D01* +X126692643Y-99601922D01* +X126683909Y-99600507D01* +X126678846Y-99599500D01* +X126678842Y-99599500D01* +X126521158Y-99599500D01* +X126521155Y-99599500D01* +X126366510Y-99630261D01* +X126366498Y-99630264D01* +X126220827Y-99690602D01* +X126220814Y-99690609D01* +X126089711Y-99778210D01* +X126089707Y-99778213D01* +X125978213Y-99889707D01* +X125978210Y-99889711D01* +X125890609Y-100020814D01* +X125890602Y-100020827D01* +X125830264Y-100166498D01* +X125830261Y-100166510D01* +X125799500Y-100321153D01* X120250500Y-100321153D01* -X120250500Y-98158653D01* -X128824500Y-98158653D01* -X128824500Y-98316346D01* -X128855261Y-98470989D01* -X128855264Y-98471001D01* -X128915602Y-98616672D01* -X128915609Y-98616685D01* -X129003210Y-98747788D01* -X129003213Y-98747792D01* -X129114707Y-98859286D01* -X129114711Y-98859289D01* -X129245814Y-98946890D01* -X129251191Y-98949764D01* -X129250422Y-98951202D01* -X129298693Y-98990100D01* -X129320758Y-99056394D01* -X129303479Y-99124094D01* -X129284519Y-99148501D01* -X129249614Y-99183406D01* -X129249610Y-99183411D01* -X129162009Y-99314514D01* -X129162002Y-99314527D01* -X129101664Y-99460198D01* -X129101661Y-99460210D01* -X129070900Y-99614853D01* -X129070900Y-99772546D01* -X129101661Y-99927189D01* -X129101664Y-99927201D01* -X129162003Y-100072874D01* -X129163113Y-100074535D01* -X129163426Y-100075536D01* -X129164875Y-100078246D01* -X129164360Y-100078520D01* -X129183987Y-100141214D01* -X129165499Y-100208593D01* -X129163109Y-100212312D01* -X129090609Y-100320814D01* -X129090602Y-100320827D01* -X129030264Y-100466498D01* -X129030261Y-100466510D01* -X128999500Y-100621153D01* -X128999500Y-100778846D01* -X129030261Y-100933489D01* -X129030264Y-100933501D01* -X129090602Y-101079172D01* -X129090609Y-101079185D01* -X129178210Y-101210288D01* -X129178213Y-101210292D01* -X129252190Y-101284269D01* -X129285675Y-101345592D01* -X129280691Y-101415284D01* -X129252193Y-101459629D01* -X129239908Y-101471914D01* -X129152309Y-101603014D01* -X129152302Y-101603027D01* -X129091964Y-101748698D01* -X129091961Y-101748710D01* -X129061200Y-101903353D01* -X129061200Y-102061046D01* -X129091961Y-102215689D01* -X129091964Y-102215701D01* -X129152302Y-102361372D01* -X129152309Y-102361385D01* -X129239910Y-102492488D01* -X129239913Y-102492492D01* -X129351407Y-102603986D01* -X129351411Y-102603989D01* -X129482514Y-102691590D01* -X129482527Y-102691597D01* -X129628198Y-102751935D01* -X129628203Y-102751937D01* -X129782853Y-102782699D01* -X129782856Y-102782700D01* -X129782858Y-102782700D01* -X129940544Y-102782700D01* -X129940545Y-102782699D01* -X130095197Y-102751937D01* -X130240879Y-102691594D01* -X130371989Y-102603989D01* -X130483489Y-102492489D01* -X130571094Y-102361379D01* -X130631437Y-102215697D01* -X130662200Y-102061042D01* -X130662200Y-101903358D01* -X130662200Y-101903355D01* -X130662199Y-101903353D01* -X130631438Y-101748710D01* -X130631437Y-101748703D01* -X130631435Y-101748698D01* -X130571097Y-101603027D01* -X130571090Y-101603014D01* -X130483489Y-101471911D01* -X130483486Y-101471907D01* -X130409509Y-101397930D01* -X130376024Y-101336607D01* -X130381008Y-101266915D01* -X130409507Y-101222570D01* -X130421789Y-101210289D01* -X130509394Y-101079179D01* -X130569737Y-100933497D01* -X130600500Y-100778842D01* -X130600500Y-100621158D01* -X130600500Y-100621155D01* -X130600499Y-100621153D01* -X130572192Y-100478846D01* -X130569737Y-100466503D01* -X130549564Y-100417801D01* -X130509397Y-100320827D01* -X130509395Y-100320824D01* -X130509394Y-100320821D01* -X130508291Y-100319171D01* -X130507980Y-100318176D01* -X130506525Y-100315454D01* -X130507041Y-100315178D01* -X130503014Y-100302318D01* -X130493160Y-100287659D01* -X130492789Y-100269669D01* -X130487412Y-100252499D01* -X130492082Y-100235380D01* -X130491720Y-100217804D01* -X130504601Y-100189494D01* -X130505717Y-100185404D01* -X130506959Y-100183379D01* -X130559028Y-100105453D01* -X138408800Y-100105453D01* -X138408800Y-100263146D01* -X138439561Y-100417789D01* -X138439564Y-100417801D01* -X138499902Y-100563472D01* -X138499909Y-100563485D01* -X138587510Y-100694588D01* -X138587513Y-100694592D01* -X138699007Y-100806086D01* -X138699011Y-100806089D01* -X138830114Y-100893690D01* -X138830127Y-100893697D01* -X138926224Y-100933501D01* -X138975803Y-100954037D01* -X139130453Y-100984799D01* -X139130456Y-100984800D01* -X139130458Y-100984800D01* -X139288144Y-100984800D01* -X139288145Y-100984799D01* -X139442797Y-100954037D01* -X139588479Y-100893694D01* -X139719589Y-100806089D01* -X139831089Y-100694589D01* -X139918694Y-100563479D01* -X139979037Y-100417797D01* -X140009800Y-100263142D01* -X140009800Y-100105458D01* -X140009800Y-100105455D01* -X140009799Y-100105453D01* -X140003319Y-100072874D01* -X139979037Y-99950803D01* -X139953732Y-99889711D01* -X139918697Y-99805127D01* -X139918690Y-99805114D01* -X139831089Y-99674011D01* -X139831086Y-99674007D01* -X139719592Y-99562513D01* -X139719588Y-99562510D01* -X139588485Y-99474909D01* -X139588472Y-99474902D01* -X139568577Y-99466662D01* -X139568572Y-99466660D01* -X139442797Y-99414563D01* -X139356071Y-99397312D01* -X139356056Y-99397307D01* -X139288146Y-99383800D01* -X139288142Y-99383800D01* -X139130458Y-99383800D01* -X139130455Y-99383800D01* -X138975810Y-99414561D01* -X138975798Y-99414564D01* -X138830127Y-99474902D01* -X138830114Y-99474909D01* -X138699011Y-99562510D01* -X138699007Y-99562513D01* -X138587513Y-99674007D01* -X138587510Y-99674011D01* -X138499909Y-99805114D01* -X138499902Y-99805127D01* -X138439564Y-99950798D01* -X138439561Y-99950810D01* -X138408800Y-100105453D01* -X130559028Y-100105453D01* -X130580794Y-100072879D01* -X130641137Y-99927197D01* -X130671900Y-99772542D01* -X130671900Y-99614858D01* -X130671900Y-99614855D01* -X130671899Y-99614853D01* -X130644062Y-99474909D01* -X130641137Y-99460203D01* -X130622233Y-99414564D01* -X130580797Y-99314527D01* -X130580790Y-99314514D01* -X130493189Y-99183411D01* -X130493186Y-99183407D01* -X130381692Y-99071913D01* -X130381688Y-99071910D01* -X130250585Y-98984309D01* -X130245209Y-98981436D01* -X130245976Y-98980000D01* -X130197698Y-98941086D01* -X130175641Y-98874790D01* -X130192928Y-98807092D01* -X130211882Y-98782696D01* -X130246786Y-98747792D01* -X130246789Y-98747789D01* -X130334394Y-98616679D01* -X130394737Y-98470997D01* -X130425500Y-98316342D01* -X130425500Y-98158658D01* -X130425500Y-98158655D01* -X130425499Y-98158653D01* -X130410078Y-98081127D01* -X130394737Y-98004003D01* -X130365415Y-97933213D01* -X130334397Y-97858327D01* -X130334390Y-97858314D01* -X130246789Y-97727211D01* -X130246786Y-97727207D01* -X130135292Y-97615713D01* -X130135288Y-97615710D01* -X130004185Y-97528109D01* -X130004172Y-97528102D01* -X129858501Y-97467764D01* -X129858489Y-97467761D01* -X129703845Y-97437000D01* -X129703842Y-97437000D01* -X129546158Y-97437000D01* -X129546155Y-97437000D01* -X129391510Y-97467761D01* -X129391498Y-97467764D01* -X129245827Y-97528102D01* -X129245814Y-97528109D01* -X129114711Y-97615710D01* -X129114707Y-97615713D01* -X129003213Y-97727207D01* -X129003210Y-97727211D01* -X128915609Y-97858314D01* -X128915602Y-97858327D01* -X128855264Y-98003998D01* -X128855261Y-98004010D01* -X128824500Y-98158653D01* -X120250500Y-98158653D01* -X120250500Y-97940666D01* -X120270185Y-97873627D01* -X120322989Y-97827872D01* -X120392147Y-97817928D01* -X120421951Y-97826105D01* -X120426217Y-97827872D01* -X120455097Y-97839835D01* -X120455099Y-97839835D01* -X120455103Y-97839837D01* -X120609753Y-97870599D01* -X120609756Y-97870600D01* -X120609758Y-97870600D01* -X120767444Y-97870600D01* -X120767445Y-97870599D01* -X120922097Y-97839837D01* -X121067779Y-97779494D01* -X121198889Y-97691889D01* -X121310389Y-97580389D01* -X121397994Y-97449279D01* -X121397995Y-97449276D01* -X121397997Y-97449273D01* -X121445077Y-97335609D01* -X121455940Y-97309382D01* -X121499780Y-97254979D01* -X121546310Y-97235217D01* -X121561297Y-97232237D01* -X121706979Y-97171894D01* -X121838089Y-97084289D01* -X121949589Y-96972789D01* -X122037194Y-96841679D01* -X122039838Y-96835297D01* -X122097535Y-96696001D01* -X122097537Y-96695997D01* -X122128300Y-96541342D01* -X122128300Y-96383658D01* -X122128300Y-96383655D01* -X122128299Y-96383653D01* -X122125245Y-96368298D01* -X122097537Y-96229003D01* -X122053431Y-96122521D01* -X122037197Y-96083327D01* -X122037190Y-96083314D01* -X121949589Y-95952211D01* -X121949586Y-95952207D01* -X121838092Y-95840713D01* -X121838088Y-95840710D01* -X121706985Y-95753109D01* -X121706972Y-95753102D01* -X121561301Y-95692764D01* -X121561289Y-95692761D01* -X121406645Y-95662000D01* -X121406642Y-95662000D01* -X121248958Y-95662000D01* -X121248955Y-95662000D01* -X121094310Y-95692761D01* -X121094298Y-95692764D01* -X120948627Y-95753102D01* -X120948614Y-95753109D01* -X120817511Y-95840710D01* -X120817507Y-95840713D01* -X120706013Y-95952207D01* -X120706010Y-95952211D01* -X120618409Y-96083314D01* -X120618404Y-96083323D01* -X120560459Y-96223217D01* -X120516618Y-96277620D01* -X120470091Y-96297381D01* -X120455107Y-96300361D01* -X120455100Y-96300363D01* -X120421952Y-96314094D01* -X120352482Y-96321563D01* -X120290003Y-96290287D01* -X120254352Y-96230198D01* -X120250500Y-96199533D01* -X120250500Y-95530753D01* -X129406800Y-95530753D01* -X129406800Y-95688446D01* -X129437561Y-95843089D01* -X129437564Y-95843101D01* -X129497902Y-95988772D01* -X129497909Y-95988785D01* -X129585510Y-96119888D01* -X129585513Y-96119892D01* -X129592671Y-96127050D01* -X129626156Y-96188373D01* -X129621172Y-96258065D01* -X129619553Y-96262178D01* -X129617765Y-96266493D01* -X129617761Y-96266505D01* -X129587000Y-96421153D01* -X129587000Y-96578846D01* -X129617761Y-96733489D01* -X129617764Y-96733501D01* -X129678102Y-96879172D01* -X129678109Y-96879185D01* -X129765710Y-97010288D01* -X129765713Y-97010292D01* -X129877207Y-97121786D01* -X129877211Y-97121789D01* -X130008314Y-97209390D01* -X130008327Y-97209397D01* -X130153998Y-97269735D01* -X130154003Y-97269737D01* -X130308653Y-97300499D01* -X130308656Y-97300500D01* -X130308658Y-97300500D01* -X130466344Y-97300500D01* -X130466345Y-97300499D01* -X130620997Y-97269737D01* -X130766679Y-97209394D01* -X130897789Y-97121789D01* -X131009289Y-97010289D01* -X131096894Y-96879179D01* -X131157237Y-96733497D01* -X131188000Y-96578842D01* -X131188000Y-96422853D01* -X138684100Y-96422853D01* -X138684100Y-96580546D01* -X138714861Y-96735189D01* -X138714864Y-96735201D01* -X138775202Y-96880872D01* -X138775209Y-96880885D01* -X138862809Y-97011987D01* -X138862810Y-97011988D01* -X138862811Y-97011989D01* -X138884324Y-97033502D01* -X138917809Y-97094823D01* -X138912826Y-97164514D01* -X138911204Y-97168635D01* -X138867064Y-97275198D01* -X138867061Y-97275210D01* -X138836300Y-97429853D01* -X138836300Y-97587546D01* -X138867061Y-97742189D01* -X138867064Y-97742201D01* -X138927402Y-97887872D01* -X138927409Y-97887885D01* -X139015010Y-98018988D01* -X139015013Y-98018992D01* -X139015825Y-98019804D01* -X139016114Y-98020333D01* -X139018876Y-98023699D01* -X139018237Y-98024222D01* -X139049310Y-98081127D01* -X139044326Y-98150819D01* -X139042706Y-98154935D01* -X139020063Y-98209602D01* -X139020060Y-98209611D01* -X138989300Y-98364253D01* -X138989300Y-98521946D01* -X139020061Y-98676589D01* -X139020064Y-98676601D01* -X139080402Y-98822272D01* -X139080409Y-98822285D01* -X139168010Y-98953388D01* -X139168013Y-98953392D01* -X139279507Y-99064886D01* -X139279511Y-99064889D01* -X139410614Y-99152490D01* -X139410621Y-99152494D01* -X139556303Y-99212837D01* -X139669355Y-99235324D01* -X139710955Y-99243600D01* -X139710958Y-99243600D01* -X139868644Y-99243600D01* -X139868645Y-99243599D01* -X140023297Y-99212837D01* -X140168979Y-99152494D01* -X140300089Y-99064889D01* -X140411589Y-98953389D01* -X140499194Y-98822279D01* -X140559537Y-98676597D01* -X140590300Y-98521942D01* -X140590300Y-98364258D01* -X140590300Y-98364255D01* -X140590299Y-98364253D01* -X140573239Y-98278489D01* -X140559537Y-98209603D01* -X140506321Y-98081127D01* -X140499197Y-98063927D01* -X140499193Y-98063920D01* -X140433867Y-97966153D01* -X144652400Y-97966153D01* -X144652400Y-98123846D01* -X144683161Y-98278489D01* -X144683164Y-98278501D01* -X144743502Y-98424172D01* -X144743509Y-98424185D01* -X144831110Y-98555288D01* -X144831113Y-98555292D01* -X144942607Y-98666786D01* -X144942611Y-98666789D01* -X145073714Y-98754390D01* -X145073727Y-98754397D01* -X145156063Y-98788501D01* -X145219403Y-98814737D01* -X145257284Y-98822272D01* -X145309178Y-98832595D01* -X145371089Y-98864980D01* -X145399548Y-98906759D01* -X145410904Y-98934175D01* -X145410909Y-98934185D01* -X145498510Y-99065288D01* -X145498513Y-99065292D01* -X145610007Y-99176786D01* -X145610011Y-99176789D01* -X145741114Y-99264390D01* -X145741127Y-99264397D01* -X145886798Y-99324735D01* -X145886803Y-99324737D01* -X146041453Y-99355499D01* -X146041456Y-99355500D01* -X146041458Y-99355500D01* -X146199144Y-99355500D01* -X146199145Y-99355499D01* -X146353797Y-99324737D01* -X146499479Y-99264394D01* -X146630589Y-99176789D01* -X146742089Y-99065289D01* -X146829694Y-98934179D01* -X146890037Y-98788497D01* -X146920800Y-98633842D01* -X146920800Y-98476158D01* -X146920800Y-98476155D01* -X146920799Y-98476153D01* -X146910459Y-98424172D01* -X146890037Y-98321503D01* -X146872225Y-98278501D01* -X146829697Y-98175827D01* -X146829690Y-98175814D01* -X146742089Y-98044711D01* -X146742086Y-98044707D01* -X146630592Y-97933213D01* -X146630588Y-97933210D01* -X146499485Y-97845609D01* -X146499472Y-97845602D01* -X146353801Y-97785264D01* -X146353791Y-97785261D01* -X146264020Y-97767404D01* -X146202109Y-97735018D01* -X146173650Y-97693238D01* -X146173091Y-97691889D01* -X146162294Y-97665821D01* -X146162290Y-97665814D01* -X146074689Y-97534711D01* -X146074686Y-97534707D01* -X145963192Y-97423213D01* -X145963188Y-97423210D01* -X145832085Y-97335609D01* -X145832072Y-97335602D01* -X145686401Y-97275264D01* -X145686389Y-97275261D01* -X145531745Y-97244500D01* -X145531742Y-97244500D01* -X145374058Y-97244500D01* -X145374055Y-97244500D01* -X145219410Y-97275261D01* -X145219398Y-97275264D01* -X145073727Y-97335602D01* -X145073714Y-97335609D01* -X144942611Y-97423210D01* -X144942607Y-97423213D01* -X144831113Y-97534707D01* -X144831110Y-97534711D01* -X144743509Y-97665814D01* -X144743502Y-97665827D01* -X144683164Y-97811498D01* -X144683161Y-97811510D01* -X144652400Y-97966153D01* -X140433867Y-97966153D01* -X140411589Y-97932811D01* -X140402958Y-97924180D01* -X140396645Y-97915100D01* -X140388947Y-97892022D01* -X140377289Y-97870672D01* -X140378089Y-97859471D01* -X140374537Y-97848820D01* -X140380537Y-97825245D01* -X140382273Y-97800980D01* -X140383894Y-97796861D01* -X140388699Y-97785261D01* -X140406537Y-97742197D01* -X140437300Y-97587542D01* -X140437300Y-97429858D01* -X140437300Y-97429855D01* -X140437299Y-97429853D01* -X140420065Y-97343214D01* -X140406537Y-97275203D01* -X140396355Y-97250621D01* -X140346197Y-97129527D01* -X140346190Y-97129514D01* -X140258589Y-96998411D01* -X140258586Y-96998407D01* -X140237076Y-96976897D01* -X140203591Y-96915574D01* -X140208575Y-96845882D01* -X140210196Y-96841763D01* -X140254337Y-96735197D01* -X140285100Y-96580542D01* -X140285100Y-96422858D01* -X140285100Y-96422855D01* -X140285099Y-96422853D01* -X140280568Y-96400075D01* -X140254337Y-96268203D01* -X140238098Y-96228998D01* -X140193997Y-96122527D01* -X140193990Y-96122514D01* -X140106389Y-95991411D01* -X140106386Y-95991407D01* -X139994892Y-95879913D01* -X139994888Y-95879910D01* -X139863785Y-95792309D01* -X139863772Y-95792302D01* -X139718101Y-95731964D01* -X139718089Y-95731961D01* -X139563445Y-95701200D01* -X139563442Y-95701200D01* -X139405758Y-95701200D01* -X139405755Y-95701200D01* -X139251110Y-95731961D01* -X139251098Y-95731964D01* -X139105427Y-95792302D01* -X139105414Y-95792309D01* -X138974311Y-95879910D01* -X138974307Y-95879913D01* -X138862813Y-95991407D01* -X138862810Y-95991411D01* -X138775209Y-96122514D01* -X138775202Y-96122527D01* -X138714864Y-96268198D01* -X138714861Y-96268210D01* -X138684100Y-96422853D01* -X131188000Y-96422853D01* -X131188000Y-96421158D01* -X131188000Y-96421155D01* -X131187999Y-96421153D01* -X131168189Y-96321563D01* -X131157237Y-96266503D01* -X131141702Y-96228998D01* -X131096897Y-96120827D01* -X131096890Y-96120814D01* -X131009289Y-95989711D01* -X131009286Y-95989707D01* -X131002128Y-95982549D01* -X130968643Y-95921226D01* -X130973627Y-95851534D01* -X130975249Y-95847413D01* -X130977037Y-95843097D01* -X131000114Y-95727080D01* -X131032498Y-95665170D01* -X131093214Y-95630596D01* -X131162983Y-95634335D01* -X131209412Y-95663591D01* -X131286707Y-95740886D01* -X131286711Y-95740889D01* -X131417814Y-95828490D01* -X131417827Y-95828497D01* -X131552286Y-95884191D01* -X131563503Y-95888837D01* -X131718153Y-95919599D01* -X131718156Y-95919600D01* -X131718158Y-95919600D01* -X131875844Y-95919600D01* -X131875845Y-95919599D01* -X132030497Y-95888837D01* -X132143166Y-95842167D01* -X132176172Y-95828497D01* -X132176172Y-95828496D01* -X132176179Y-95828494D01* -X132307289Y-95740889D01* -X132418789Y-95629389D01* -X132506394Y-95498279D01* -X132515800Y-95475572D01* -X132520067Y-95465266D01* -X132566737Y-95352597D01* -X132597500Y-95197942D01* -X132597500Y-95040258D01* -X132596586Y-95035663D01* -X132596586Y-95035660D01* -X132596585Y-95035657D01* -X132592984Y-95017553D01* -X133974500Y-95017553D01* -X133974500Y-95175246D01* -X134005261Y-95329889D01* -X134005264Y-95329901D01* -X134065602Y-95475572D01* -X134065609Y-95475585D01* -X134153210Y-95606688D01* -X134153213Y-95606692D01* -X134264707Y-95718186D01* -X134264711Y-95718189D01* -X134395814Y-95805790D01* -X134395827Y-95805797D01* -X134541498Y-95866135D01* -X134541503Y-95866137D01* -X134696153Y-95896899D01* -X134696156Y-95896900D01* -X134696158Y-95896900D01* -X134853844Y-95896900D01* -X134853845Y-95896899D01* -X135008497Y-95866137D01* -X135154179Y-95805794D01* -X135285289Y-95718189D01* -X135396789Y-95606689D01* -X135484394Y-95475579D01* -X135544737Y-95329897D01* -X135575500Y-95175242D01* -X135575500Y-95162753D01* -X137101200Y-95162753D01* -X137101200Y-95320446D01* -X137131961Y-95475089D01* -X137131964Y-95475101D01* -X137192302Y-95620772D01* -X137192309Y-95620785D01* -X137279910Y-95751888D01* -X137279913Y-95751892D01* -X137391407Y-95863386D01* -X137391411Y-95863389D01* -X137522514Y-95950990D01* -X137522527Y-95950997D01* -X137642093Y-96000522D01* -X137668203Y-96011337D01* -X137822853Y-96042099D01* -X137822856Y-96042100D01* -X137822858Y-96042100D01* -X137980544Y-96042100D01* -X137980545Y-96042099D01* -X138135197Y-96011337D01* -X138280879Y-95950994D01* -X138411989Y-95863389D01* -X138523489Y-95751889D01* -X138611094Y-95620779D01* -X138671437Y-95475097D01* -X138702200Y-95320442D01* -X138702200Y-95162758D01* -X138702200Y-95162755D01* -X138702199Y-95162753D01* -X138671437Y-95008103D01* -X138663032Y-94987811D01* -X138611097Y-94862427D01* -X138611090Y-94862414D01* -X138523489Y-94731311D01* -X138523486Y-94731307D01* -X138411992Y-94619813D01* -X138411988Y-94619810D01* -X138280885Y-94532209D01* -X138280872Y-94532202D01* -X138135201Y-94471864D01* -X138135189Y-94471861D01* -X137980545Y-94441100D01* -X137980542Y-94441100D01* -X137822858Y-94441100D01* -X137822855Y-94441100D01* -X137668210Y-94471861D01* -X137668198Y-94471864D01* -X137522527Y-94532202D01* -X137522514Y-94532209D01* -X137391411Y-94619810D01* -X137391407Y-94619813D01* -X137279913Y-94731307D01* -X137279910Y-94731311D01* -X137192309Y-94862414D01* -X137192302Y-94862427D01* -X137131964Y-95008098D01* -X137131961Y-95008110D01* -X137101200Y-95162753D01* -X135575500Y-95162753D01* -X135575500Y-95017558D01* -X135575500Y-95017555D01* -X135575499Y-95017553D01* -X135573618Y-95008098D01* -X135544737Y-94862903D01* -X135544537Y-94862421D01* -X135484397Y-94717227D01* -X135484390Y-94717214D01* -X135396789Y-94586111D01* -X135396786Y-94586107D01* -X135285292Y-94474613D01* -X135285288Y-94474610D01* -X135154185Y-94387009D01* -X135154172Y-94387002D01* -X135008501Y-94326664D01* -X135008489Y-94326661D01* -X134853845Y-94295900D01* -X134853842Y-94295900D01* -X134696158Y-94295900D01* -X134696155Y-94295900D01* -X134541510Y-94326661D01* -X134541498Y-94326664D01* -X134395827Y-94387002D01* -X134395814Y-94387009D01* -X134264711Y-94474610D01* -X134264707Y-94474613D01* -X134153213Y-94586107D01* -X134153210Y-94586111D01* -X134065609Y-94717214D01* -X134065602Y-94717227D01* -X134005264Y-94862898D01* -X134005261Y-94862910D01* -X133974500Y-95017553D01* -X132592984Y-95017553D01* -X132569642Y-94900209D01* -X132566737Y-94885603D01* -X132557337Y-94862910D01* -X132506397Y-94739927D01* -X132506390Y-94739914D01* -X132418789Y-94608811D01* -X132418786Y-94608807D01* -X132307292Y-94497313D01* -X132307288Y-94497310D01* -X132176185Y-94409709D01* -X132176172Y-94409702D01* -X132030501Y-94349364D01* -X132030489Y-94349361D01* -X131875845Y-94318600D01* -X131875842Y-94318600D01* -X131718158Y-94318600D01* -X131718155Y-94318600D01* -X131563510Y-94349361D01* -X131563498Y-94349364D01* -X131417827Y-94409702D01* -X131417814Y-94409709D01* -X131286711Y-94497310D01* -X131286707Y-94497313D01* -X131175213Y-94608807D01* -X131175210Y-94608811D01* -X131087609Y-94739914D01* -X131087602Y-94739927D01* -X131027264Y-94885598D01* -X131027261Y-94885608D01* -X131004185Y-95001619D01* -X130971800Y-95063530D01* -X130911084Y-95098104D01* -X130841314Y-95094363D01* -X130794887Y-95065108D01* -X130717592Y-94987813D01* -X130717588Y-94987810D01* -X130586485Y-94900209D01* -X130586472Y-94900202D01* -X130440801Y-94839864D01* -X130440789Y-94839861D01* -X130286145Y-94809100D01* -X130286142Y-94809100D01* -X130128458Y-94809100D01* -X130128455Y-94809100D01* -X129973810Y-94839861D01* -X129973798Y-94839864D01* -X129828127Y-94900202D01* -X129828114Y-94900209D01* -X129697011Y-94987810D01* -X129697007Y-94987813D01* -X129585513Y-95099307D01* -X129585510Y-95099311D01* -X129497909Y-95230414D01* -X129497902Y-95230427D01* -X129437564Y-95376098D01* -X129437561Y-95376110D01* -X129406800Y-95530753D01* -X120250500Y-95530753D01* -X120250500Y-93597753D01* -X125869600Y-93597753D01* -X125869600Y-93755446D01* -X125900361Y-93910089D01* -X125900364Y-93910101D01* -X125960702Y-94055772D01* -X125960709Y-94055785D01* -X126048310Y-94186888D01* -X126048313Y-94186892D01* -X126159807Y-94298386D01* -X126159811Y-94298389D01* -X126290914Y-94385990D01* -X126290927Y-94385997D01* -X126436598Y-94446335D01* -X126436603Y-94446337D01* -X126564920Y-94471861D01* -X126591253Y-94477099D01* -X126591256Y-94477100D01* -X126591258Y-94477100D01* -X126748944Y-94477100D01* -X126748945Y-94477099D01* -X126903597Y-94446337D01* -X127046836Y-94387006D01* -X127049272Y-94385997D01* -X127049272Y-94385996D01* -X127049279Y-94385994D01* -X127180389Y-94298389D01* -X127291889Y-94186889D01* -X127379494Y-94055779D01* -X127395700Y-94016655D01* -X127395701Y-94016653D01* -X128264500Y-94016653D01* -X128264500Y-94174346D01* -X128295261Y-94328989D01* -X128295264Y-94329001D01* -X128355602Y-94474672D01* -X128355609Y-94474685D01* -X128443210Y-94605788D01* -X128443213Y-94605792D01* -X128554707Y-94717286D01* -X128554711Y-94717289D01* -X128685814Y-94804890D01* -X128685827Y-94804897D01* -X128824719Y-94862427D01* -X128831503Y-94865237D01* -X128986153Y-94895999D01* -X128986156Y-94896000D01* -X128986158Y-94896000D01* -X129143844Y-94896000D01* -X129143845Y-94895999D01* -X129298497Y-94865237D01* -X129444179Y-94804894D01* -X129575289Y-94717289D01* -X129686789Y-94605789D01* -X129774394Y-94474679D01* -X129775561Y-94471863D01* -X129811130Y-94385990D01* -X129834737Y-94328997D01* -X129865500Y-94174342D01* -X129865500Y-94016658D01* -X129865500Y-94016655D01* -X129865499Y-94016653D01* -X129844304Y-93910101D01* -X129834737Y-93862003D01* -X129790600Y-93755446D01* -X129774397Y-93716327D01* -X129774390Y-93716314D01* -X129686789Y-93585211D01* -X129686786Y-93585207D01* -X129575292Y-93473713D01* -X129575288Y-93473710D01* -X129444185Y-93386109D01* -X129444172Y-93386102D01* -X129298501Y-93325764D01* -X129298489Y-93325761D01* -X129143845Y-93295000D01* -X129143842Y-93295000D01* -X128986158Y-93295000D01* -X128986155Y-93295000D01* -X128831510Y-93325761D01* -X128831498Y-93325764D01* -X128685827Y-93386102D01* -X128685814Y-93386109D01* -X128554711Y-93473710D01* -X128554707Y-93473713D01* -X128443213Y-93585207D01* -X128443210Y-93585211D01* -X128355609Y-93716314D01* -X128355602Y-93716327D01* -X128295264Y-93861998D01* -X128295261Y-93862010D01* -X128264500Y-94016653D01* -X127395701Y-94016653D01* -X127417877Y-93963114D01* -X127417877Y-93963113D01* -X127439837Y-93910097D01* -X127470600Y-93755442D01* -X127470600Y-93597758D01* -X127470600Y-93597755D01* -X127470599Y-93597753D01* -X127441884Y-93453391D01* -X127448111Y-93383800D01* -X127490974Y-93328622D01* -X127556864Y-93305378D01* -X127563501Y-93305200D01* -X127604544Y-93305200D01* -X127604545Y-93305199D01* -X127759197Y-93274437D01* -X127904879Y-93214094D01* -X128035989Y-93126489D01* -X128147489Y-93014989D01* -X128235094Y-92883879D01* -X128235935Y-92881850D01* -X128274351Y-92789104D01* -X128295437Y-92738197D01* -X128297996Y-92725330D01* -X128301373Y-92708353D01* -X133908600Y-92708353D01* -X133908600Y-92866046D01* -X133939361Y-93020689D01* -X133939364Y-93020701D01* -X133999702Y-93166372D01* -X133999709Y-93166385D01* -X134087310Y-93297488D01* -X134087313Y-93297492D01* -X134198807Y-93408986D01* -X134198811Y-93408989D01* -X134329914Y-93496590D01* -X134329927Y-93496597D01* -X134475598Y-93556935D01* -X134475603Y-93556937D01* -X134617725Y-93585207D01* -X134630253Y-93587699D01* -X134630256Y-93587700D01* -X134630258Y-93587700D01* -X134787944Y-93587700D01* -X134787945Y-93587699D01* -X134942597Y-93556937D01* -X135088279Y-93496594D01* -X135219389Y-93408989D01* -X135227623Y-93400754D01* -X135288941Y-93367270D01* -X135358633Y-93372252D01* -X135362756Y-93373874D01* -X135500998Y-93431135D01* -X135501003Y-93431137D01* -X135612881Y-93453391D01* -X135655653Y-93461899D01* -X135655656Y-93461900D01* -X135655658Y-93461900D01* -X135813344Y-93461900D01* -X135813345Y-93461899D01* -X135967997Y-93431137D01* -X136081106Y-93384286D01* -X136113672Y-93370797D01* -X136113672Y-93370796D01* -X136113679Y-93370794D01* -X136244789Y-93283189D01* -X136356289Y-93171689D01* -X136443894Y-93040579D01* -X136504237Y-92894897D01* -X136535000Y-92740242D01* -X136535000Y-92683653D01* -X140520800Y-92683653D01* -X140520800Y-92841346D01* -X140551561Y-92995989D01* -X140551564Y-92996001D01* -X140611902Y-93141672D01* -X140611909Y-93141685D01* -X140699510Y-93272788D01* -X140699513Y-93272792D01* -X140811007Y-93384286D01* -X140811011Y-93384289D01* -X140942114Y-93471890D01* -X140942127Y-93471897D01* -X141087798Y-93532235D01* -X141087803Y-93532237D01* -X141242453Y-93562999D01* -X141242456Y-93563000D01* -X141242458Y-93563000D01* -X141400144Y-93563000D01* -X141400145Y-93562999D01* -X141554797Y-93532237D01* -X141696088Y-93473713D01* -X141700472Y-93471897D01* -X141700472Y-93471896D01* -X141700479Y-93471894D01* -X141831589Y-93384289D01* -X141943089Y-93272789D01* -X142030694Y-93141679D01* -X142091037Y-92995997D01* -X142108767Y-92906863D01* -X142113743Y-92881850D01* -X142146128Y-92819939D01* -X142206844Y-92785365D01* -X142276613Y-92789104D01* -X142333285Y-92829971D01* -X142338462Y-92837150D01* -X142377910Y-92896188D01* -X142377913Y-92896192D01* -X142489407Y-93007686D01* -X142489411Y-93007689D01* -X142620514Y-93095290D01* -X142620527Y-93095297D01* -X142766198Y-93155635D01* -X142766203Y-93155637D01* -X142920853Y-93186399D01* -X142920856Y-93186400D01* -X142920858Y-93186400D01* -X143078544Y-93186400D01* -X143078545Y-93186399D01* -X143233197Y-93155637D01* -X143378879Y-93095294D01* -X143509989Y-93007689D01* -X143621489Y-92896189D01* -X143709094Y-92765079D01* -X143769437Y-92619397D01* -X143800200Y-92464742D01* -X143800200Y-92307058D01* -X143800200Y-92307055D01* -X143800199Y-92307053D01* -X143794203Y-92276911D01* -X143769437Y-92152403D01* -X143739999Y-92081332D01* -X143709097Y-92006727D01* -X143709090Y-92006714D01* -X143621489Y-91875611D01* -X143621486Y-91875607D01* -X143509992Y-91764113D01* -X143509988Y-91764110D01* -X143378885Y-91676509D01* -X143378872Y-91676502D01* -X143233201Y-91616164D01* -X143233189Y-91616161D01* -X143078545Y-91585400D01* -X143078542Y-91585400D01* -X142920858Y-91585400D01* -X142920855Y-91585400D01* -X142766210Y-91616161D01* -X142766198Y-91616164D01* -X142620527Y-91676502D01* -X142620514Y-91676509D01* -X142489411Y-91764110D01* -X142489407Y-91764113D01* -X142377913Y-91875607D01* -X142377910Y-91875611D01* -X142290309Y-92006714D01* -X142290302Y-92006727D01* -X142229964Y-92152398D01* -X142229961Y-92152407D01* -X142207256Y-92266551D01* -X142174870Y-92328461D01* -X142114154Y-92363035D01* -X142044385Y-92359294D01* -X141987713Y-92318427D01* -X141982537Y-92311248D01* -X141943092Y-92252215D01* -X141943086Y-92252207D01* -X141831592Y-92140713D01* -X141831588Y-92140710D01* -X141700485Y-92053109D01* -X141700472Y-92053102D01* -X141554801Y-91992764D01* -X141554789Y-91992761D01* -X141400145Y-91962000D01* -X141400142Y-91962000D01* -X141242458Y-91962000D01* -X141242455Y-91962000D01* -X141087810Y-91992761D01* -X141087798Y-91992764D01* -X140942127Y-92053102D01* -X140942114Y-92053109D01* -X140811011Y-92140710D01* -X140811007Y-92140713D01* -X140699513Y-92252207D01* -X140699510Y-92252211D01* -X140611909Y-92383314D01* -X140611902Y-92383327D01* -X140551564Y-92528998D01* -X140551561Y-92529010D01* -X140520800Y-92683653D01* -X136535000Y-92683653D01* -X136535000Y-92582558D01* -X136535000Y-92582555D01* -X136534999Y-92582553D01* -X136529259Y-92553698D01* -X136504237Y-92427903D01* -X136477368Y-92363035D01* -X136443897Y-92282227D01* -X136443890Y-92282214D01* -X136356289Y-92151111D01* -X136356286Y-92151107D01* -X136244792Y-92039613D01* -X136244788Y-92039610D01* -X136113685Y-91952009D01* -X136113672Y-91952002D01* -X135968001Y-91891664D01* -X135967989Y-91891661D01* -X135813345Y-91860900D01* -X135813342Y-91860900D01* -X135655658Y-91860900D01* -X135655655Y-91860900D01* -X135501010Y-91891661D01* -X135500998Y-91891664D01* -X135355327Y-91952002D01* -X135355314Y-91952009D01* -X135224214Y-92039608D01* -X135224206Y-92039615D01* -X135215968Y-92047852D01* -X135154642Y-92081332D01* -X135084951Y-92076342D01* -X135080842Y-92074725D01* -X134942601Y-92017464D01* -X134942589Y-92017461D01* -X134787945Y-91986700D01* -X134787942Y-91986700D01* -X134630258Y-91986700D01* -X134630255Y-91986700D01* -X134475610Y-92017461D01* -X134475598Y-92017464D01* -X134329927Y-92077802D01* -X134329914Y-92077809D01* -X134198811Y-92165410D01* -X134198807Y-92165413D01* -X134087313Y-92276907D01* -X134087310Y-92276911D01* -X133999709Y-92408014D01* -X133999702Y-92408027D01* -X133939364Y-92553698D01* -X133939361Y-92553710D01* -X133908600Y-92708353D01* -X128301373Y-92708353D01* -X128307397Y-92678074D01* -X128307397Y-92678073D01* -X128326199Y-92583546D01* -X128326200Y-92583544D01* -X128326200Y-92425855D01* -X128326199Y-92425853D01* -X128317737Y-92383314D01* -X128295437Y-92271203D01* -X128251617Y-92165411D01* -X128235097Y-92125527D01* -X128235090Y-92125514D01* -X128147489Y-91994411D01* -X128147486Y-91994407D01* -X128035992Y-91882913D01* -X128035988Y-91882910D01* -X127904885Y-91795309D01* -X127904878Y-91795305D01* -X127891558Y-91789788D01* -X127884279Y-91786773D01* -X127829876Y-91742933D01* -X127807810Y-91676639D01* -X127825088Y-91608940D01* -X127876225Y-91561329D01* -X127884257Y-91557659D01* -X127940429Y-91534393D01* -X128071539Y-91446788D01* -X128183039Y-91335288D01* -X128270644Y-91204178D01* -X128330987Y-91058496D01* -X128361750Y-90903841D01* -X128361750Y-90746157D01* -X128361750Y-90746154D01* -X128361749Y-90746152D01* -X128330988Y-90591509D01* -X128330987Y-90591502D01* -X128329807Y-90588653D01* -X128270647Y-90445826D01* -X128270640Y-90445813D01* -X128183039Y-90314710D01* -X128183036Y-90314706D01* -X128071542Y-90203212D01* -X128071538Y-90203209D01* -X127944001Y-90117991D01* -X127940433Y-90115607D01* -X127940422Y-90115601D01* -X127794751Y-90055263D01* -X127794739Y-90055260D01* -X127640095Y-90024499D01* -X127640092Y-90024499D01* -X127482408Y-90024499D01* -X127482405Y-90024499D01* -X127327760Y-90055260D01* -X127327748Y-90055263D01* -X127182077Y-90115601D01* -X127182064Y-90115608D01* -X127050961Y-90203209D01* -X127050957Y-90203212D01* -X126939463Y-90314706D01* -X126939460Y-90314710D01* -X126851859Y-90445813D01* -X126851852Y-90445826D01* -X126791514Y-90591497D01* -X126791511Y-90591509D01* -X126760750Y-90746152D01* -X126760750Y-90903845D01* -X126791511Y-91058488D01* -X126791514Y-91058500D01* -X126851852Y-91204171D01* -X126851859Y-91204184D01* -X126939460Y-91335287D01* -X126939463Y-91335291D01* -X127050957Y-91446785D01* -X127050961Y-91446788D01* -X127182064Y-91534389D01* -X127182066Y-91534390D01* -X127182071Y-91534393D01* -X127202669Y-91542925D01* -X127257072Y-91586763D01* -X127279139Y-91653056D01* -X127261862Y-91720756D01* -X127210726Y-91768368D01* -X127202672Y-91772047D01* -X127146521Y-91795306D01* -X127146514Y-91795309D01* -X127015411Y-91882910D01* -X127015407Y-91882913D01* -X126903913Y-91994407D01* -X126903910Y-91994411D01* -X126816309Y-92125514D01* -X126816302Y-92125527D01* -X126755964Y-92271198D01* -X126755961Y-92271210D01* -X126725200Y-92425853D01* -X126725200Y-92583546D01* -X126753916Y-92727909D01* -X126747689Y-92797500D01* -X126704826Y-92852678D01* -X126638936Y-92875922D01* -X126632299Y-92876100D01* -X126591255Y-92876100D01* -X126436610Y-92906861D01* -X126436598Y-92906864D01* -X126290927Y-92967202D01* -X126290914Y-92967209D01* -X126159811Y-93054810D01* -X126159807Y-93054813D01* -X126048313Y-93166307D01* -X126048310Y-93166311D01* -X125960709Y-93297414D01* -X125960702Y-93297427D01* -X125900364Y-93443098D01* -X125900361Y-93443110D01* -X125869600Y-93597753D01* -X120250500Y-93597753D01* -X120250500Y-90360753D01* -X122757300Y-90360753D01* -X122757300Y-90518446D01* -X122788061Y-90673089D01* -X122788064Y-90673101D01* -X122848402Y-90818772D01* -X122848409Y-90818785D01* -X122936010Y-90949888D01* -X122936013Y-90949892D01* -X123047507Y-91061386D01* -X123047511Y-91061389D01* -X123178614Y-91148990D01* -X123178627Y-91148997D01* -X123311831Y-91204171D01* -X123324303Y-91209337D01* -X123478953Y-91240099D01* -X123478956Y-91240100D01* -X123478958Y-91240100D01* -X123636644Y-91240100D01* -X123636645Y-91240099D01* -X123791297Y-91209337D01* -X123936979Y-91148994D01* -X124068089Y-91061389D01* -X124179589Y-90949889D01* -X124267194Y-90818779D01* -X124327537Y-90673097D01* -X124358300Y-90518442D01* -X124358300Y-90360758D01* -X124358300Y-90360755D01* -X124358299Y-90360753D01* -X124355790Y-90348138D01* -X124327537Y-90206103D01* -X124316442Y-90179317D01* -X124267197Y-90060427D01* -X124267190Y-90060414D01* -X124179589Y-89929311D01* -X124179586Y-89929307D01* -X124068092Y-89817813D01* -X124068088Y-89817810D01* -X123936985Y-89730209D01* -X123936972Y-89730202D01* -X123791301Y-89669864D01* -X123791289Y-89669861D01* -X123636645Y-89639100D01* -X123636642Y-89639100D01* -X123478958Y-89639100D01* -X123478955Y-89639100D01* -X123324310Y-89669861D01* -X123324298Y-89669864D01* -X123178627Y-89730202D01* -X123178614Y-89730209D01* -X123047511Y-89817810D01* -X123047507Y-89817813D01* -X122936013Y-89929307D01* -X122936010Y-89929311D01* -X122848409Y-90060414D01* -X122848402Y-90060427D01* -X122788064Y-90206098D01* -X122788061Y-90206110D01* -X122757300Y-90360753D01* -X120250500Y-90360753D01* +X120250500Y-98021153D01* +X123099500Y-98021153D01* +X123099500Y-98178846D01* +X123130261Y-98333489D01* +X123130264Y-98333501D01* +X123190602Y-98479172D01* +X123190609Y-98479185D01* +X123278210Y-98610288D01* +X123278213Y-98610292D01* +X123389707Y-98721786D01* +X123389711Y-98721789D01* +X123520814Y-98809390D01* +X123520827Y-98809397D01* +X123656585Y-98865629D01* +X123666503Y-98869737D01* +X123821153Y-98900499D01* +X123821156Y-98900500D01* +X123821158Y-98900500D01* +X123978844Y-98900500D01* +X123978845Y-98900499D01* +X124133497Y-98869737D01* +X124279179Y-98809394D01* +X124410289Y-98721789D01* +X124521789Y-98610289D01* +X124609394Y-98479179D01* +X124669737Y-98333497D01* +X124700500Y-98178842D01* +X124700500Y-98021158D01* +X124700500Y-98021155D01* +X124700499Y-98021153D01* +X124680925Y-97922749D01* +X124669737Y-97866503D01* +X124661221Y-97845943D01* +X124609397Y-97720827D01* +X124609390Y-97720814D01* +X124521789Y-97589711D01* +X124521786Y-97589707D01* +X124410289Y-97478210D01* +X124280149Y-97391253D01* +X125349500Y-97391253D01* +X125349500Y-97548946D01* +X125380261Y-97703589D01* +X125380264Y-97703601D01* +X125440602Y-97849272D01* +X125440609Y-97849285D01* +X125528210Y-97980388D01* +X125528213Y-97980392D01* +X125639707Y-98091886D01* +X125639711Y-98091889D01* +X125770814Y-98179490D01* +X125770827Y-98179497D01* +X125916498Y-98239835D01* +X125916503Y-98239837D01* +X126071153Y-98270599D01* +X126071156Y-98270600D01* +X126071158Y-98270600D01* +X126228844Y-98270600D01* +X126228845Y-98270599D01* +X126383497Y-98239837D01* +X126529179Y-98179494D01* +X126578884Y-98146282D01* +X139085387Y-98146282D01* +X139085387Y-98303975D01* +X139116148Y-98458618D01* +X139116151Y-98458630D01* +X139176489Y-98604301D01* +X139176496Y-98604314D01* +X139264097Y-98735417D01* +X139264100Y-98735421D01* +X139375594Y-98846915D01* +X139375598Y-98846918D01* +X139506701Y-98934519D01* +X139506714Y-98934526D01* +X139614532Y-98979185D01* +X139652390Y-98994866D01* +X139807040Y-99025628D01* +X139807043Y-99025629D01* +X139807045Y-99025629D01* +X139964731Y-99025629D01* +X139964732Y-99025628D01* +X140119384Y-98994866D01* +X140265066Y-98934523D01* +X140396176Y-98846918D01* +X140507676Y-98735418D01* +X140595281Y-98604308D01* +X140655624Y-98458626D01* +X140686387Y-98303971D01* +X140686387Y-98146287D01* +X140686387Y-98146284D01* +X140686386Y-98146282D01* +X140676285Y-98095496D01* +X140672684Y-98077392D01* +X146233858Y-98077392D01* +X146233858Y-98235085D01* +X146264619Y-98389728D01* +X146264622Y-98389740D01* +X146324960Y-98535411D01* +X146324967Y-98535424D01* +X146412568Y-98666527D01* +X146412571Y-98666531D01* +X146524065Y-98778025D01* +X146524069Y-98778028D01* +X146655172Y-98865629D01* +X146655185Y-98865636D01* +X146789217Y-98921153D01* +X146800861Y-98925976D01* +X146860027Y-98937745D01* +X146928316Y-98951329D01* +X146990227Y-98983714D01* +X147007227Y-99004055D01* +X147078210Y-99110288D01* +X147078213Y-99110292D01* +X147189707Y-99221786D01* +X147189711Y-99221789D01* +X147320814Y-99309390D01* +X147320827Y-99309397D01* +X147466498Y-99369735D01* +X147466503Y-99369737D01* +X147616131Y-99399500D01* +X147621153Y-99400499D01* +X147621156Y-99400500D01* +X147621158Y-99400500D01* +X147778844Y-99400500D01* +X147778845Y-99400499D01* +X147933497Y-99369737D01* +X148079179Y-99309394D01* +X148210289Y-99221789D01* +X148321789Y-99110289D01* +X148409394Y-98979179D01* +X148469737Y-98833497D01* +X148500500Y-98678842D01* +X148500500Y-98521158D01* +X148500500Y-98521155D01* +X148500499Y-98521153D01* +X148488062Y-98458630D01* +X148469737Y-98366503D01* +X148456062Y-98333489D01* +X148409397Y-98220827D01* +X148409390Y-98220814D01* +X148321789Y-98089711D01* +X148321786Y-98089707D01* +X148210292Y-97978213D01* +X148210288Y-97978210D01* +X148079185Y-97890609D01* +X148079172Y-97890602D01* +X147933501Y-97830264D01* +X147933491Y-97830261D01* +X147806040Y-97804909D01* +X147744129Y-97772524D01* +X147727130Y-97752183D01* +X147656147Y-97645950D01* +X147656144Y-97645946D01* +X147544650Y-97534452D01* +X147544646Y-97534449D01* +X147413543Y-97446848D01* +X147413530Y-97446841D01* +X147267859Y-97386503D01* +X147267847Y-97386500D01* +X147113203Y-97355739D01* +X147113200Y-97355739D01* +X146955516Y-97355739D01* +X146955513Y-97355739D01* +X146800868Y-97386500D01* +X146800856Y-97386503D01* +X146655185Y-97446841D01* +X146655172Y-97446848D01* +X146524069Y-97534449D01* +X146524065Y-97534452D01* +X146412571Y-97645946D01* +X146412568Y-97645950D01* +X146324967Y-97777053D01* +X146324960Y-97777066D01* +X146264622Y-97922737D01* +X146264619Y-97922749D01* +X146233858Y-98077392D01* +X140672684Y-98077392D01* +X140655625Y-97991637D01* +X140655624Y-97991636D01* +X140655624Y-97991632D01* +X140650065Y-97978211D01* +X140595284Y-97845956D01* +X140595277Y-97845943D01* +X140507676Y-97714840D01* +X140507673Y-97714836D01* +X140396179Y-97603342D01* +X140396175Y-97603339D01* +X140265072Y-97515738D01* +X140265059Y-97515731D01* +X140119388Y-97455393D01* +X140119376Y-97455390D01* +X139964732Y-97424629D01* +X139964729Y-97424629D01* +X139807045Y-97424629D01* +X139807042Y-97424629D01* +X139652397Y-97455390D01* +X139652385Y-97455393D01* +X139506714Y-97515731D01* +X139506701Y-97515738D01* +X139375598Y-97603339D01* +X139375594Y-97603342D01* +X139264100Y-97714836D01* +X139264097Y-97714840D01* +X139176496Y-97845943D01* +X139176489Y-97845956D01* +X139116151Y-97991627D01* +X139116148Y-97991639D01* +X139085387Y-98146282D01* +X126578884Y-98146282D01* +X126660289Y-98091889D01* +X126771789Y-97980389D01* +X126859394Y-97849279D01* +X126860771Y-97845956D01* +X126873067Y-97816266D01* +X126919737Y-97703597D01* +X126950500Y-97548942D01* +X126950500Y-97391258D01* +X126950500Y-97391255D01* +X126933062Y-97303591D01* +X128408540Y-97303591D01* +X128442112Y-97326023D01* +X128560401Y-97375020D01* +X128560409Y-97375022D01* +X128685976Y-97399999D01* +X128685980Y-97400000D01* +X128814020Y-97400000D01* +X128814023Y-97399999D01* +X128939590Y-97375022D01* +X128939594Y-97375021D01* +X129057891Y-97326020D01* +X129057898Y-97326016D01* +X129091458Y-97303591D01* +X129091459Y-97303590D01* +X128750001Y-96962132D01* +X128750000Y-96962132D01* +X128408540Y-97303591D01* +X126933062Y-97303591D01* +X126928682Y-97281572D01* +X126928682Y-97281571D01* +X126919738Y-97236610D01* +X126919737Y-97236603D01* +X126859617Y-97091459D01* +X126859397Y-97090927D01* +X126859390Y-97090914D01* +X126771789Y-96959811D01* +X126771786Y-96959807D01* +X126660292Y-96848313D01* +X126660288Y-96848310D01* +X126562532Y-96782991D01* +X126529185Y-96760709D01* +X126529172Y-96760702D01* +X126383501Y-96700364D01* +X126383489Y-96700361D01* +X126311172Y-96685976D01* +X128100000Y-96685976D01* +X128100000Y-96814023D01* +X128124977Y-96939590D01* +X128124979Y-96939598D01* +X128173976Y-97057886D01* +X128173981Y-97057896D01* +X128196407Y-97091458D01* +X128196408Y-97091458D01* +X128537868Y-96750000D01* +X128537868Y-96749999D01* +X128517978Y-96730109D01* +X128650000Y-96730109D01* +X128650000Y-96769891D01* +X128665224Y-96806645D01* +X128693355Y-96834776D01* +X128730109Y-96850000D01* +X128769891Y-96850000D01* +X128806645Y-96834776D01* +X128834776Y-96806645D01* +X128850000Y-96769891D01* +X128850000Y-96749999D01* +X128962132Y-96749999D01* +X128962132Y-96750001D01* +X129303590Y-97091459D01* +X129303591Y-97091458D01* +X129326016Y-97057898D01* +X129326020Y-97057891D01* +X129375021Y-96939594D01* +X129375022Y-96939590D01* +X129399999Y-96814023D01* +X129400000Y-96814020D01* +X129400000Y-96685980D01* +X129399999Y-96685976D01* +X129375022Y-96560409D01* +X129375020Y-96560401D01* +X129326023Y-96442112D01* +X129303591Y-96408540D01* +X128962132Y-96749999D01* +X128850000Y-96749999D01* +X128850000Y-96730109D01* +X128834776Y-96693355D01* +X128806645Y-96665224D01* +X128769891Y-96650000D01* +X128730109Y-96650000D01* +X128693355Y-96665224D01* +X128665224Y-96693355D01* +X128650000Y-96730109D01* +X128517978Y-96730109D01* +X128196408Y-96408539D01* +X128196407Y-96408540D01* +X128173978Y-96442109D01* +X128124979Y-96560401D01* +X128124977Y-96560409D01* +X128100000Y-96685976D01* +X126311172Y-96685976D01* +X126228845Y-96669600D01* +X126228842Y-96669600D01* +X126071158Y-96669600D01* +X126071155Y-96669600D01* +X125916510Y-96700361D01* +X125916498Y-96700364D01* +X125770827Y-96760702D01* +X125770814Y-96760709D01* +X125639711Y-96848310D01* +X125639707Y-96848313D01* +X125528213Y-96959807D01* +X125528210Y-96959811D01* +X125440609Y-97090914D01* +X125440602Y-97090927D01* +X125380264Y-97236598D01* +X125380261Y-97236610D01* +X125349500Y-97391253D01* +X124280149Y-97391253D01* +X124279185Y-97390609D01* +X124279172Y-97390602D01* +X124133501Y-97330264D01* +X124133489Y-97330261D01* +X123978845Y-97299500D01* +X123978842Y-97299500D01* +X123821158Y-97299500D01* +X123821155Y-97299500D01* +X123666510Y-97330261D01* +X123666498Y-97330264D01* +X123520827Y-97390602D01* +X123520814Y-97390609D01* +X123389711Y-97478210D01* +X123389707Y-97478213D01* +X123278213Y-97589707D01* +X123278210Y-97589711D01* +X123190609Y-97720814D01* +X123190602Y-97720827D01* +X123130264Y-97866498D01* +X123130261Y-97866510D01* +X123099500Y-98021153D01* +X120250500Y-98021153D01* +X120250500Y-96250000D01* +X128462132Y-96250000D01* +X128750000Y-96537868D01* +X129037868Y-96250000D01* +X128750000Y-95962132D01* +X128462132Y-96250000D01* +X120250500Y-96250000D01* +X120250500Y-95171153D01* +X122949500Y-95171153D01* +X122949500Y-95328846D01* +X122980261Y-95483489D01* +X122980264Y-95483501D01* +X123040602Y-95629172D01* +X123040609Y-95629185D01* +X123128210Y-95760288D01* +X123128213Y-95760292D01* +X123239707Y-95871786D01* +X123239711Y-95871789D01* +X123370814Y-95959390D01* +X123370827Y-95959397D01* +X123516498Y-96019735D01* +X123516503Y-96019737D01* +X123671153Y-96050499D01* +X123671156Y-96050500D01* +X123671158Y-96050500D01* +X123828844Y-96050500D01* +X123828845Y-96050499D01* +X123983497Y-96019737D01* +X124129179Y-95959394D01* +X124260289Y-95871789D01* +X124371789Y-95760289D01* +X124421443Y-95685976D01* +X128100000Y-95685976D01* +X128100000Y-95814023D01* +X128124977Y-95939590D01* +X128124979Y-95939598D01* +X128173976Y-96057886D01* +X128173981Y-96057896D01* +X128196407Y-96091458D01* +X128196408Y-96091458D01* +X128537868Y-95750000D01* +X128537868Y-95749999D01* +X128517978Y-95730109D01* +X128650000Y-95730109D01* +X128650000Y-95769891D01* +X128665224Y-95806645D01* +X128693355Y-95834776D01* +X128730109Y-95850000D01* +X128769891Y-95850000D01* +X128806645Y-95834776D01* +X128834776Y-95806645D01* +X128850000Y-95769891D01* +X128850000Y-95749999D01* +X128962132Y-95749999D01* +X128962132Y-95750001D01* +X129303590Y-96091459D01* +X129303591Y-96091458D01* +X129326016Y-96057898D01* +X129326020Y-96057891D01* +X129375021Y-95939594D01* +X129375022Y-95939590D01* +X129399999Y-95814023D01* +X129400000Y-95814020D01* +X129400000Y-95685980D01* +X129399999Y-95685976D01* +X129375022Y-95560409D01* +X129375020Y-95560401D01* +X129326023Y-95442112D01* +X129303591Y-95408540D01* +X128962132Y-95749999D01* +X128850000Y-95749999D01* +X128850000Y-95730109D01* +X128834776Y-95693355D01* +X128806645Y-95665224D01* +X128769891Y-95650000D01* +X128730109Y-95650000D01* +X128693355Y-95665224D01* +X128665224Y-95693355D01* +X128650000Y-95730109D01* +X128517978Y-95730109D01* +X128196408Y-95408539D01* +X128196407Y-95408540D01* +X128173978Y-95442109D01* +X128124979Y-95560401D01* +X128124977Y-95560409D01* +X128100000Y-95685976D01* +X124421443Y-95685976D01* +X124459394Y-95629179D01* +X124519737Y-95483497D01* +X124550500Y-95328842D01* +X124550500Y-95196408D01* +X128408539Y-95196408D01* +X128750000Y-95537868D01* +X128750001Y-95537868D01* +X129091458Y-95196408D01* +X129091458Y-95196407D01* +X129057896Y-95173981D01* +X129057886Y-95173976D01* +X128939598Y-95124979D01* +X128939590Y-95124977D01* +X128814023Y-95100000D01* +X128685976Y-95100000D01* +X128560409Y-95124977D01* +X128560401Y-95124979D01* +X128442109Y-95173978D01* +X128408540Y-95196407D01* +X128408539Y-95196408D01* +X124550500Y-95196408D01* +X124550500Y-95171158D01* +X124550500Y-95171155D01* +X124550499Y-95171153D01* +X124519738Y-95016510D01* +X124519737Y-95016503D01* +X124483427Y-94928842D01* +X124459397Y-94870827D01* +X124459390Y-94870814D01* +X124434763Y-94833957D01* +X124392798Y-94771153D01* +X138699500Y-94771153D01* +X138699500Y-94928846D01* +X138730261Y-95083489D01* +X138730264Y-95083501D01* +X138790602Y-95229172D01* +X138790609Y-95229185D01* +X138878210Y-95360288D01* +X138878213Y-95360292D01* +X138989707Y-95471786D01* +X138989711Y-95471789D01* +X139120814Y-95559390D01* +X139120827Y-95559397D01* +X139266498Y-95619735D01* +X139266503Y-95619737D01* +X139418644Y-95650000D01* +X139421153Y-95650499D01* +X139421156Y-95650500D01* +X139421158Y-95650500D01* +X139578844Y-95650500D01* +X139578845Y-95650499D01* +X139733497Y-95619737D01* +X139879179Y-95559394D01* +X140010289Y-95471789D01* +X140121789Y-95360289D01* +X140209394Y-95229179D01* +X140269737Y-95083497D01* +X140300500Y-94928842D01* +X140300500Y-94771158D01* +X140300500Y-94771155D01* +X140300499Y-94771153D01* +X140272066Y-94628211D01* +X140269737Y-94616503D01* +X140238298Y-94540602D01* +X140209397Y-94470827D01* +X140209390Y-94470814D01* +X140121789Y-94339711D01* +X140121786Y-94339707D01* +X140010292Y-94228213D01* +X140010288Y-94228210D01* +X139879185Y-94140609D01* +X139879172Y-94140602D01* +X139733501Y-94080264D01* +X139733489Y-94080261D01* +X139578845Y-94049500D01* +X139578842Y-94049500D01* +X139421158Y-94049500D01* +X139421155Y-94049500D01* +X139266510Y-94080261D01* +X139266498Y-94080264D01* +X139120827Y-94140602D01* +X139120814Y-94140609D01* +X138989711Y-94228210D01* +X138989707Y-94228213D01* +X138878213Y-94339707D01* +X138878210Y-94339711D01* +X138790609Y-94470814D01* +X138790602Y-94470827D01* +X138730264Y-94616498D01* +X138730261Y-94616510D01* +X138699500Y-94771153D01* +X124392798Y-94771153D01* +X124371789Y-94739711D01* +X124371786Y-94739707D01* +X124260292Y-94628213D01* +X124260288Y-94628210D01* +X124129185Y-94540609D01* +X124129172Y-94540602D01* +X123983501Y-94480264D01* +X123983489Y-94480261D01* +X123828845Y-94449500D01* +X123828842Y-94449500D01* +X123671158Y-94449500D01* +X123671155Y-94449500D01* +X123516510Y-94480261D01* +X123516498Y-94480264D01* +X123370827Y-94540602D01* +X123370814Y-94540609D01* +X123239711Y-94628210D01* +X123239707Y-94628213D01* +X123128213Y-94739707D01* +X123128210Y-94739711D01* +X123040609Y-94870814D01* +X123040602Y-94870827D01* +X122980264Y-95016498D01* +X122980261Y-95016510D01* +X122949500Y-95171153D01* +X120250500Y-95171153D01* +X120250500Y-92936152D01* +X126960750Y-92936152D01* +X126960750Y-93093845D01* +X126991511Y-93248488D01* +X126991514Y-93248500D01* +X127051852Y-93394171D01* +X127051859Y-93394184D01* +X127139460Y-93525287D01* +X127139463Y-93525291D01* +X127250957Y-93636785D01* +X127250961Y-93636788D01* +X127382064Y-93724389D01* +X127382077Y-93724396D01* +X127527748Y-93784734D01* +X127527753Y-93784736D01* +X127682403Y-93815498D01* +X127682406Y-93815499D01* +X127682408Y-93815499D01* +X127840094Y-93815499D01* +X127840095Y-93815498D01* +X127994747Y-93784736D01* +X128128860Y-93729185D01* +X128140422Y-93724396D01* +X128140422Y-93724395D01* +X128140429Y-93724393D01* +X128271539Y-93636788D01* +X128383039Y-93525288D01* +X128470644Y-93394178D01* +X128521602Y-93271153D01* +X128899500Y-93271153D01* +X128899500Y-93428846D01* +X128930261Y-93583489D01* +X128930264Y-93583501D01* +X128990602Y-93729172D01* +X128990609Y-93729185D01* +X129078210Y-93860288D01* +X129078213Y-93860292D01* +X129189707Y-93971786D01* +X129189711Y-93971789D01* +X129320814Y-94059390D01* +X129320827Y-94059397D01* +X129466498Y-94119735D01* +X129466503Y-94119737D01* +X129621153Y-94150499D01* +X129621156Y-94150500D01* +X129621158Y-94150500D01* +X129778844Y-94150500D01* +X129778845Y-94150499D01* +X129933497Y-94119737D01* +X130079179Y-94059394D01* +X130210289Y-93971789D01* +X130321789Y-93860289D01* +X130409394Y-93729179D01* +X130469737Y-93583497D01* +X130500500Y-93428842D01* +X130500500Y-93341804D01* +X130520185Y-93274765D01* +X130555606Y-93238704D01* +X130580923Y-93221789D01* +X130631559Y-93171153D01* +X137699500Y-93171153D01* +X137699500Y-93328846D01* +X137730261Y-93483489D01* +X137730264Y-93483501D01* +X137790602Y-93629172D01* +X137790609Y-93629185D01* +X137878210Y-93760288D01* +X137878213Y-93760292D01* +X137989707Y-93871786D01* +X137989711Y-93871789D01* +X138120814Y-93959390D01* +X138120827Y-93959397D01* +X138266498Y-94019735D01* +X138266503Y-94019737D01* +X138416131Y-94049500D01* +X138421153Y-94050499D01* +X138421156Y-94050500D01* +X138421158Y-94050500D01* +X138578844Y-94050500D01* +X138578845Y-94050499D01* +X138733497Y-94019737D01* +X138879179Y-93959394D01* +X139010289Y-93871789D01* +X139121789Y-93760289D01* +X139209394Y-93629179D01* +X139269737Y-93483497D01* +X139300500Y-93328842D01* +X139300500Y-93171158D01* +X139300500Y-93171155D01* +X139300499Y-93171153D01* +X139285121Y-93093843D01* +X139269737Y-93016503D01* +X139269735Y-93016498D01* +X139209397Y-92870827D01* +X139209390Y-92870814D01* +X139121789Y-92739711D01* +X139121786Y-92739707D01* +X139010292Y-92628213D01* +X139010288Y-92628210D01* +X138879185Y-92540609D01* +X138879172Y-92540602D01* +X138733501Y-92480264D01* +X138733489Y-92480261D01* +X138578845Y-92449500D01* +X138578842Y-92449500D01* +X138421158Y-92449500D01* +X138421155Y-92449500D01* +X138266510Y-92480261D01* +X138266498Y-92480264D01* +X138120827Y-92540602D01* +X138120814Y-92540609D01* +X137989711Y-92628210D01* +X137989707Y-92628213D01* +X137878213Y-92739707D01* +X137878210Y-92739711D01* +X137790609Y-92870814D01* +X137790602Y-92870827D01* +X137730264Y-93016498D01* +X137730261Y-93016510D01* +X137699500Y-93171153D01* +X130631559Y-93171153D01* +X130692423Y-93110289D01* +X130703414Y-93093841D01* +X130780024Y-92979185D01* +X130780024Y-92979184D01* +X130780028Y-92979179D01* +X130783488Y-92970827D01* +X130797850Y-92936152D01* +X130840371Y-92833497D01* +X130871134Y-92678842D01* +X130871134Y-92521158D01* +X130871134Y-92521155D01* +X130871133Y-92521153D01* +X130856880Y-92449500D01* +X130840371Y-92366503D01* +X130815148Y-92305608D01* +X130780031Y-92220827D01* +X130780024Y-92220814D01* +X130692423Y-92089711D01* +X130692420Y-92089707D01* +X130580926Y-91978213D01* +X130580922Y-91978210D01* +X130449819Y-91890609D01* +X130449806Y-91890602D01* +X130304135Y-91830264D01* +X130304123Y-91830261D01* +X130149479Y-91799500D01* +X130149476Y-91799500D01* +X129991792Y-91799500D01* +X129991789Y-91799500D01* +X129837144Y-91830261D01* +X129837132Y-91830264D01* +X129691461Y-91890602D01* +X129691448Y-91890609D01* +X129560345Y-91978210D01* +X129560341Y-91978213D01* +X129448847Y-92089707D01* +X129448844Y-92089711D01* +X129361243Y-92220814D01* +X129361236Y-92220827D01* +X129300898Y-92366498D01* +X129300895Y-92366510D01* +X129270134Y-92521153D01* +X129270134Y-92608194D01* +X129250449Y-92675233D01* +X129215026Y-92711296D01* +X129189707Y-92728213D01* +X129078213Y-92839707D01* +X129078210Y-92839711D01* +X128990609Y-92970814D01* +X128990602Y-92970827D01* +X128930264Y-93116498D01* +X128930261Y-93116510D01* +X128899500Y-93271153D01* +X128521602Y-93271153D01* +X128530987Y-93248496D01* +X128557241Y-93116510D01* +X128561750Y-93093843D01* +X128561750Y-92936154D01* +X128561749Y-92936152D01* +X128548752Y-92870814D01* +X128530987Y-92781502D01* +X128508914Y-92728213D01* +X128470647Y-92635826D01* +X128470640Y-92635813D01* +X128383039Y-92504710D01* +X128383036Y-92504706D01* +X128271542Y-92393212D01* +X128271538Y-92393209D01* +X128140435Y-92305608D01* +X128140422Y-92305601D01* +X127994751Y-92245263D01* +X127994739Y-92245260D01* +X127840095Y-92214499D01* +X127840092Y-92214499D01* +X127682408Y-92214499D01* +X127682405Y-92214499D01* +X127527760Y-92245260D01* +X127527748Y-92245263D01* +X127382077Y-92305601D01* +X127382064Y-92305608D01* +X127250961Y-92393209D01* +X127250957Y-92393212D01* +X127139463Y-92504706D01* +X127139460Y-92504710D01* +X127051859Y-92635813D01* +X127051852Y-92635826D01* +X126991514Y-92781497D01* +X126991511Y-92781509D01* +X126960750Y-92936152D01* +X120250500Y-92936152D01* +X120250500Y-90621153D01* +X140149500Y-90621153D01* +X140149500Y-90778846D01* +X140180261Y-90933489D01* +X140180264Y-90933501D01* +X140240602Y-91079172D01* +X140240609Y-91079185D01* +X140328210Y-91210288D01* +X140328213Y-91210292D01* +X140439707Y-91321786D01* +X140439711Y-91321789D01* +X140570814Y-91409390D01* +X140570827Y-91409397D01* +X140670060Y-91450500D01* +X140716503Y-91469737D01* +X140871153Y-91500499D01* +X140871156Y-91500500D01* +X140871158Y-91500500D01* +X141028844Y-91500500D01* +X141028845Y-91500499D01* +X141183497Y-91469737D01* +X141329179Y-91409394D01* +X141460289Y-91321789D01* +X141571789Y-91210289D01* +X141659394Y-91079179D01* +X141719737Y-90933497D01* +X141750500Y-90778842D01* +X141750500Y-90621158D01* +X141750500Y-90621155D01* +X141744155Y-90589258D01* +X141744155Y-90589257D01* +X141740554Y-90571153D01* +X143999500Y-90571153D01* +X143999500Y-90728846D01* +X144030261Y-90883489D01* +X144030264Y-90883501D01* +X144090602Y-91029172D01* +X144090609Y-91029185D01* +X144178210Y-91160288D01* +X144178213Y-91160292D01* +X144289707Y-91271786D01* +X144289711Y-91271789D01* +X144420814Y-91359390D01* +X144420827Y-91359397D01* +X144566498Y-91419735D01* +X144566503Y-91419737D01* +X144721153Y-91450499D01* +X144721156Y-91450500D01* +X144721158Y-91450500D01* +X144878844Y-91450500D01* +X144878845Y-91450499D01* +X145033497Y-91419737D01* +X145179179Y-91359394D01* +X145310289Y-91271789D01* +X145421789Y-91160289D01* +X145509394Y-91029179D01* +X145569737Y-90883497D01* +X145600500Y-90728842D01* +X145600500Y-90571158D01* +X145600500Y-90571155D01* +X145600499Y-90571153D01* +X145579684Y-90466510D01* +X145569737Y-90416503D01* +X145530102Y-90320814D01* +X145509397Y-90270827D01* +X145509390Y-90270814D01* +X145421789Y-90139711D01* +X145421786Y-90139707D01* +X145310292Y-90028213D01* +X145310288Y-90028210D01* +X145179185Y-89940609D01* +X145179172Y-89940602D01* +X145033501Y-89880264D01* +X145033489Y-89880261D01* +X144878845Y-89849500D01* +X144878842Y-89849500D01* +X144721158Y-89849500D01* +X144721155Y-89849500D01* +X144566510Y-89880261D01* +X144566498Y-89880264D01* +X144420827Y-89940602D01* +X144420814Y-89940609D01* +X144289711Y-90028210D01* +X144289707Y-90028213D01* +X144178213Y-90139707D01* +X144178210Y-90139711D01* +X144090609Y-90270814D01* +X144090602Y-90270827D01* +X144030264Y-90416498D01* +X144030261Y-90416510D01* +X143999500Y-90571153D01* +X141740554Y-90571153D01* +X141719738Y-90466510D01* +X141719737Y-90466503D01* +X141719735Y-90466498D01* +X141659397Y-90320827D01* +X141659390Y-90320814D01* +X141571789Y-90189711D01* +X141571786Y-90189707D01* +X141460292Y-90078213D01* +X141460288Y-90078210D01* +X141329185Y-89990609D01* +X141329172Y-89990602D01* +X141183501Y-89930264D01* +X141183489Y-89930261D01* +X141028845Y-89899500D01* +X141028842Y-89899500D01* +X140871158Y-89899500D01* +X140871155Y-89899500D01* +X140716510Y-89930261D01* +X140716498Y-89930264D01* +X140570827Y-89990602D01* +X140570814Y-89990609D01* +X140439711Y-90078210D01* +X140439707Y-90078213D01* +X140328213Y-90189707D01* +X140328210Y-90189711D01* +X140240609Y-90320814D01* +X140240602Y-90320827D01* +X140180264Y-90466498D01* +X140180261Y-90466510D01* +X140149500Y-90621153D01* +X120250500Y-90621153D01* +X120250500Y-88622110D01* +X130125000Y-88622110D01* +X130125000Y-88877889D01* +X130165013Y-89130523D01* +X130244051Y-89373781D01* +X130244052Y-89373784D01* +X130360175Y-89601686D01* +X130437850Y-89708595D01* +X130437850Y-89708596D01* +X131168092Y-88978354D01* +X131196132Y-89046048D01* +X131264531Y-89148414D01* +X131351586Y-89235469D01* +X131453952Y-89303868D01* +X131521645Y-89331907D01* +X130791402Y-90062148D01* +X130898313Y-90139824D01* +X131126215Y-90255947D01* +X131126218Y-90255948D01* +X131369476Y-90334986D01* +X131622111Y-90375000D01* +X131877889Y-90375000D01* +X132130523Y-90334986D01* +X132373781Y-90255948D01* +X132373784Y-90255947D01* +X132601685Y-90139825D01* +X132708595Y-90062148D01* +X132708596Y-90062148D01* +X131978354Y-89331907D01* +X132046048Y-89303868D01* +X132148414Y-89235469D01* +X132235469Y-89148414D01* +X132303868Y-89046048D01* +X132331907Y-88978354D01* +X133062148Y-89708596D01* +X133062148Y-89708595D01* +X133139825Y-89601685D01* +X133255947Y-89373784D01* +X133255948Y-89373781D01* +X133334986Y-89130523D01* +X133375000Y-88877889D01* +X133375000Y-88622110D01* +X133374994Y-88622070D01* +X136624500Y-88622070D01* +X136624500Y-88877930D01* +X136644513Y-89004284D01* +X136664526Y-89130640D01* +X136743588Y-89373972D01* +X136743589Y-89373975D01* +X136859750Y-89601950D01* +X137010132Y-89808935D01* +X137010136Y-89808940D01* +X137191059Y-89989863D01* +X137191064Y-89989867D01* +X137312663Y-90078213D01* +X137398053Y-90140252D01* +X137547080Y-90216185D01* +X137626024Y-90256410D01* +X137626027Y-90256411D01* +X137670396Y-90270827D01* +X137869361Y-90335474D01* +X138122070Y-90375500D01* +X138122071Y-90375500D01* +X138377929Y-90375500D01* +X138377930Y-90375500D01* +X138630639Y-90335474D01* +X138873975Y-90256410D01* +X139101947Y-90140252D01* +X139308942Y-89989862D01* +X139489862Y-89808942D01* +X139640252Y-89601947D01* +X139756410Y-89373975D01* +X139835474Y-89130639D01* +X139875500Y-88877930D01* +X139875500Y-88622070D01* +X139835474Y-88369361D01* +X139773681Y-88179179D01* +X139756411Y-88126027D01* +X139756410Y-88126024D01* +X139640384Y-87898313D01* +X139640252Y-87898053D01* +X139511729Y-87721155D01* +X139489867Y-87691064D01* +X139489863Y-87691059D01* +X139308940Y-87510136D01* +X139308935Y-87510132D01* +X139101950Y-87359750D01* +X139101949Y-87359749D01* +X139101947Y-87359748D01* +X139028910Y-87322533D01* +X138873975Y-87243589D01* +X138873972Y-87243588D01* +X138630640Y-87164526D01* +X138504284Y-87144513D01* +X138377930Y-87124500D01* +X138122070Y-87124500D01* +X138037833Y-87137842D01* +X137869359Y-87164526D01* +X137626027Y-87243588D01* +X137626024Y-87243589D01* +X137398049Y-87359750D01* +X137191064Y-87510132D01* +X137191059Y-87510136D01* +X137010136Y-87691059D01* +X137010132Y-87691064D01* +X136859750Y-87898049D01* +X136743589Y-88126024D01* +X136743588Y-88126027D01* +X136664526Y-88369359D01* +X136656222Y-88421789D01* +X136624500Y-88622070D01* +X133374994Y-88622070D01* +X133334986Y-88369476D01* +X133255948Y-88126218D01* +X133255947Y-88126215D01* +X133139824Y-87898313D01* +X133062148Y-87791403D01* +X133062148Y-87791402D01* +X132331906Y-88521644D01* +X132303868Y-88453952D01* +X132235469Y-88351586D01* +X132148414Y-88264531D01* +X132046048Y-88196132D01* +X131978353Y-88168092D01* +X132708596Y-87437850D01* +X132601686Y-87360175D01* +X132373784Y-87244052D01* +X132373781Y-87244051D01* +X132130523Y-87165013D01* +X131877889Y-87125000D01* +X131622111Y-87125000D01* +X131369476Y-87165013D01* +X131126218Y-87244051D01* +X131126215Y-87244052D01* +X130898310Y-87360177D01* +X130791403Y-87437849D01* +X130791402Y-87437850D01* +X131521645Y-88168092D01* +X131453952Y-88196132D01* +X131351586Y-88264531D01* +X131264531Y-88351586D01* +X131196132Y-88453952D01* +X131168092Y-88521645D01* +X130437850Y-87791402D01* +X130437849Y-87791403D01* +X130360177Y-87898310D01* +X130244052Y-88126215D01* +X130244051Y-88126218D01* +X130165013Y-88369476D01* +X130125000Y-88622110D01* +X120250500Y-88622110D01* +X120250500Y-87721153D01* +X121499500Y-87721153D01* +X121499500Y-87878846D01* +X121530261Y-88033489D01* +X121530264Y-88033501D01* +X121590602Y-88179172D01* +X121590609Y-88179185D01* +X121678210Y-88310288D01* +X121678213Y-88310292D01* +X121789707Y-88421786D01* +X121789711Y-88421789D01* +X121920814Y-88509390D01* +X121920827Y-88509397D01* +X122061571Y-88567694D01* +X122066503Y-88569737D01* +X122221153Y-88600499D01* +X122221156Y-88600500D01* +X122221158Y-88600500D01* +X122378844Y-88600500D01* +X122378845Y-88600499D01* +X122533497Y-88569737D01* +X122679179Y-88509394D01* +X122810289Y-88421789D01* +X122921789Y-88310289D01* +X123009394Y-88179179D01* +X123069737Y-88033497D01* +X123100500Y-87878842D01* +X123100500Y-87721158D01* +X123100500Y-87721155D01* +X123100499Y-87721153D01* +X123069738Y-87566510D01* +X123069737Y-87566503D01* +X123016447Y-87437849D01* +X123009395Y-87420823D01* +X123009390Y-87420814D01* +X122921789Y-87289711D01* +X122921786Y-87289707D01* +X122810292Y-87178213D01* +X122810288Y-87178210D01* +X122679185Y-87090609D01* +X122679172Y-87090602D01* +X122533501Y-87030264D01* +X122533489Y-87030261D01* +X122378845Y-86999500D01* +X122378842Y-86999500D01* +X122221158Y-86999500D01* +X122221155Y-86999500D01* +X122066510Y-87030261D01* +X122066498Y-87030264D01* +X121920827Y-87090602D01* +X121920814Y-87090609D01* +X121789711Y-87178210D01* +X121789707Y-87178213D01* +X121678213Y-87289707D01* +X121678210Y-87289711D01* +X121590609Y-87420814D01* +X121590602Y-87420827D01* +X121530264Y-87566498D01* +X121530261Y-87566510D01* +X121499500Y-87721153D01* +X120250500Y-87721153D01* X120250500Y-85693995D01* X121099499Y-85693995D01* X121126418Y-85829322D01* @@ -4183,7 +5094,137 @@ X121868995Y-86325500D01* X121960041Y-86307389D01* X122004328Y-86298580D01* X122131811Y-86245775D01* +X122168660Y-86221153D01* +X143799500Y-86221153D01* +X143799500Y-86378846D01* +X143830261Y-86533489D01* +X143830264Y-86533501D01* +X143890602Y-86679172D01* +X143890609Y-86679185D01* +X143978210Y-86810288D01* +X143978213Y-86810292D01* +X144089707Y-86921786D01* +X144089711Y-86921789D01* +X144220814Y-87009390D01* +X144220827Y-87009397D01* +X144366498Y-87069735D01* +X144366503Y-87069737D01* +X144521153Y-87100499D01* +X144521156Y-87100500D01* +X144521158Y-87100500D01* +X144678844Y-87100500D01* +X144678845Y-87100499D01* +X144833497Y-87069737D01* +X144979179Y-87009394D01* +X145110289Y-86921789D01* +X145221789Y-86810289D01* +X145309394Y-86679179D01* +X145369737Y-86533497D01* +X145400500Y-86378842D01* +X145400500Y-86221158D01* +X145400500Y-86221155D01* +X145400499Y-86221153D01* +X145369738Y-86066510D01* +X145369737Y-86066503D01* +X145324304Y-85956817D01* +X145309397Y-85920827D01* +X145309390Y-85920814D01* +X145221789Y-85789711D01* +X145221786Y-85789707D01* +X145126074Y-85693995D01* +X147499499Y-85693995D01* +X147526418Y-85829322D01* +X147526421Y-85829332D01* +X147579221Y-85956804D01* +X147579228Y-85956817D01* +X147655885Y-86071541D01* +X147655888Y-86071545D01* +X147753454Y-86169111D01* +X147753458Y-86169114D01* +X147868182Y-86245771D01* +X147868195Y-86245778D01* +X147995667Y-86298578D01* +X147995672Y-86298580D01* +X147995676Y-86298580D01* +X147995677Y-86298581D01* +X148131004Y-86325500D01* +X148131007Y-86325500D01* +X148268995Y-86325500D01* +X148360041Y-86307389D01* +X148404328Y-86298580D01* +X148531811Y-86245775D01* +X148646542Y-86169114D01* +X148744114Y-86071542D01* +X148820775Y-85956811D01* +X148873580Y-85829328D01* +X148888084Y-85756411D01* +X148900500Y-85693995D01* +X148900500Y-85556004D01* +X148873581Y-85420677D01* +X148873580Y-85420676D01* +X148873580Y-85420672D01* +X148873578Y-85420667D01* +X148820778Y-85293195D01* +X148820771Y-85293182D01* +X148744114Y-85178458D01* +X148744111Y-85178454D01* +X148646545Y-85080888D01* +X148646541Y-85080885D01* +X148531817Y-85004228D01* +X148531804Y-85004221D01* +X148404332Y-84951421D01* +X148404322Y-84951418D01* +X148268995Y-84924500D01* +X148268993Y-84924500D01* +X148131007Y-84924500D01* +X148131005Y-84924500D01* +X147995677Y-84951418D01* +X147995667Y-84951421D01* +X147868195Y-85004221D01* +X147868182Y-85004228D01* +X147753458Y-85080885D01* +X147753454Y-85080888D01* +X147655888Y-85178454D01* +X147655885Y-85178458D01* +X147579228Y-85293182D01* +X147579221Y-85293195D01* +X147526421Y-85420667D01* +X147526418Y-85420677D01* +X147499500Y-85556004D01* +X147499500Y-85556007D01* +X147499500Y-85693993D01* +X147499500Y-85693995D01* +X147499499Y-85693995D01* +X145126074Y-85693995D01* +X145110292Y-85678213D01* +X145110288Y-85678210D01* +X145072584Y-85653017D01* +X144979185Y-85590609D01* +X144979172Y-85590602D01* +X144833501Y-85530264D01* +X144833489Y-85530261D01* +X144678845Y-85499500D01* +X144678842Y-85499500D01* +X144521158Y-85499500D01* +X144521155Y-85499500D01* +X144366510Y-85530261D01* +X144366498Y-85530264D01* +X144220827Y-85590602D01* +X144220814Y-85590609D01* +X144089711Y-85678210D01* +X144089707Y-85678213D01* +X143978213Y-85789707D01* +X143978210Y-85789711D01* +X143890609Y-85920814D01* +X143890602Y-85920827D01* +X143830264Y-86066498D01* +X143830261Y-86066510D01* +X143799500Y-86221153D01* +X122168660Y-86221153D01* X122246542Y-86169114D01* +X122246545Y-86169111D01* +X122288272Y-86127385D01* +X122344111Y-86071545D01* X122344114Y-86071542D01* X122420775Y-85956811D01* X122473580Y-85829328D01* @@ -4193,7 +5234,7 @@ X122500500Y-85556004D01* X122473581Y-85420677D01* X122473580Y-85420676D01* X122473580Y-85420672D01* -X122461175Y-85390724D01* +X122473578Y-85420667D01* X122420778Y-85293195D01* X122420771Y-85293182D01* X122344114Y-85178458D01* @@ -4226,43 +5267,11 @@ X121099500Y-85693993D01* X121099500Y-85693995D01* X121099499Y-85693995D01* X120250500Y-85693995D01* -X120250500Y-83355253D01* -X123954100Y-83355253D01* -X123954100Y-83512946D01* -X123984861Y-83667589D01* -X123984864Y-83667601D01* -X124045202Y-83813272D01* -X124045209Y-83813285D01* -X124132810Y-83944388D01* -X124132813Y-83944392D01* -X124244307Y-84055886D01* -X124244311Y-84055889D01* -X124375414Y-84143490D01* -X124375427Y-84143497D01* -X124521098Y-84203835D01* -X124521103Y-84203837D01* -X124675753Y-84234599D01* -X124675756Y-84234600D01* -X124675758Y-84234600D01* -X124833444Y-84234600D01* -X124833445Y-84234599D01* -X124988097Y-84203837D01* -X125124318Y-84147413D01* -X125133772Y-84143497D01* -X125133772Y-84143496D01* -X125133779Y-84143494D01* -X125264889Y-84055889D01* -X125376389Y-83944389D01* -X125463994Y-83813279D01* -X125524337Y-83667597D01* -X125555100Y-83512942D01* -X125555100Y-83383634D01* +X120250500Y-83383634D01* X126899500Y-83383634D01* X126899500Y-83616365D01* X126899501Y-83616382D01* -X126925423Y-83813285D01* -X126929879Y-83847126D01* -X126986867Y-84059809D01* +X126929878Y-83847122D01* X126990120Y-84071947D01* X127079180Y-84286960D01* X127079188Y-84286976D01* @@ -4287,7 +5296,7 @@ X128791365Y-85275500D01* X128791372Y-85275500D01* X129022126Y-85245121D01* X129246940Y-85184882D01* -X129304953Y-85160852D01* +X129447165Y-85101947D01* X129461960Y-85095819D01* X129461963Y-85095817D01* X129461969Y-85095815D01* @@ -4307,388 +5316,19 @@ X130510132Y-85308935D01* X130510136Y-85308940D01* X130691059Y-85489863D01* X130691064Y-85489867D01* -X130818167Y-85582212D01* +X130782095Y-85556004D01* X130898053Y-85640252D01* X131047080Y-85716185D01* -X131126024Y-85756410D01* -X131126027Y-85756411D01* -X131247693Y-85795942D01* -X131369361Y-85835474D01* -X131622070Y-85875500D01* -X131622071Y-85875500D01* -X131877928Y-85875500D01* -X131877930Y-85875500D01* -X132004187Y-85855502D01* -X132073478Y-85864456D01* -X132126930Y-85909452D01* -X132147570Y-85976203D01* -X132128846Y-86043517D01* -X132111265Y-86065656D01* -X131999010Y-86177911D01* -X131911409Y-86309014D01* -X131911402Y-86309027D01* -X131851064Y-86454698D01* -X131851061Y-86454710D01* -X131820300Y-86609353D01* -X131820300Y-86767046D01* -X131851061Y-86921689D01* -X131851063Y-86921697D01* -X131864256Y-86953547D01* -X131871725Y-87023016D01* -X131840450Y-87085496D01* -X131780361Y-87121148D01* -X131749695Y-87125000D01* -X131622111Y-87125000D01* -X131369476Y-87165013D01* -X131126218Y-87244051D01* -X131126215Y-87244052D01* -X130898310Y-87360177D01* -X130791403Y-87437849D01* -X130791402Y-87437850D01* -X131521645Y-88168092D01* -X131453952Y-88196132D01* -X131351586Y-88264531D01* -X131264531Y-88351586D01* -X131196132Y-88453952D01* -X131168092Y-88521645D01* -X130437850Y-87791402D01* -X130437849Y-87791403D01* -X130360177Y-87898310D01* -X130244052Y-88126215D01* -X130244051Y-88126218D01* -X130165013Y-88369476D01* -X130125000Y-88622110D01* -X130125000Y-88877889D01* -X130165013Y-89130523D01* -X130244051Y-89373781D01* -X130244052Y-89373784D01* -X130360175Y-89601686D01* -X130437850Y-89708595D01* -X130437850Y-89708596D01* -X131168092Y-88978354D01* -X131196132Y-89046048D01* -X131264531Y-89148414D01* -X131351586Y-89235469D01* -X131453952Y-89303868D01* -X131521645Y-89331907D01* -X130791402Y-90062148D01* -X130898313Y-90139824D01* -X131126215Y-90255947D01* -X131126218Y-90255948D01* -X131369476Y-90334986D01* -X131622111Y-90375000D01* -X131877889Y-90375000D01* -X132130523Y-90334986D01* -X132373781Y-90255948D01* -X132373784Y-90255947D01* -X132601686Y-90139824D01* -X132700010Y-90068388D01* -X132765817Y-90044908D01* -X132833871Y-90060733D01* -X132882566Y-90110839D01* -X132896441Y-90179317D01* -X132875998Y-90237597D01* -X132842109Y-90288314D01* -X132842102Y-90288327D01* -X132781764Y-90433998D01* -X132781761Y-90434010D01* -X132751000Y-90588653D01* -X132751000Y-90746346D01* -X132781761Y-90900989D01* -X132781764Y-90901001D01* -X132842102Y-91046672D01* -X132842109Y-91046685D01* -X132929710Y-91177788D01* -X132929713Y-91177792D01* -X133041207Y-91289286D01* -X133041211Y-91289289D01* -X133172314Y-91376890D01* -X133172327Y-91376897D01* -X133317998Y-91437235D01* -X133318003Y-91437237D01* -X133472653Y-91467999D01* -X133472656Y-91468000D01* -X133472658Y-91468000D01* -X133630344Y-91468000D01* -X133630345Y-91467999D01* -X133784997Y-91437237D01* -X133930679Y-91376894D01* -X134061789Y-91289289D01* -X134173289Y-91177789D01* -X134260894Y-91046679D01* -X134321237Y-90900997D01* -X134352000Y-90746342D01* -X134352000Y-90588658D01* -X134352000Y-90588655D01* -X134351999Y-90588653D01* -X134338033Y-90518442D01* -X134321237Y-90434003D01* -X134298413Y-90378900D01* -X134260897Y-90288327D01* -X134260890Y-90288314D01* -X134173289Y-90157211D01* -X134173286Y-90157207D01* -X134061792Y-90045713D01* -X134061788Y-90045710D01* -X133930685Y-89958109D01* -X133930672Y-89958102D01* -X133785001Y-89897764D01* -X133784989Y-89897761D01* -X133630345Y-89867000D01* -X133630342Y-89867000D01* -X133472658Y-89867000D01* -X133472655Y-89867000D01* -X133318010Y-89897761D01* -X133317998Y-89897764D01* -X133172320Y-89958105D01* -X133171867Y-89958348D01* -X133171602Y-89958403D01* -X133166692Y-89960437D01* -X133166306Y-89959505D01* -X133103463Y-89972583D01* -X133038221Y-89947577D01* -X132996856Y-89891268D01* -X132992500Y-89821534D01* -X133013106Y-89776098D01* -X133139824Y-89601686D01* -X133255947Y-89373784D01* -X133255948Y-89373781D01* -X133334986Y-89130523D01* -X133375000Y-88877889D01* -X133375000Y-88622110D01* -X133374994Y-88622070D01* -X136624500Y-88622070D01* -X136624500Y-88877930D01* -X136636962Y-88956610D01* -X136664526Y-89130640D01* -X136743588Y-89373972D01* -X136743589Y-89373975D01* -X136859750Y-89601950D01* -X137010132Y-89808935D01* -X137010136Y-89808940D01* -X137191059Y-89989863D01* -X137191064Y-89989867D01* -X137299140Y-90068388D01* -X137398053Y-90140252D01* -X137527306Y-90206110D01* -X137626024Y-90256410D01* -X137626027Y-90256411D01* -X137722616Y-90287794D01* -X137869361Y-90335474D01* -X138122070Y-90375500D01* -X138122071Y-90375500D01* -X138377929Y-90375500D01* -X138377930Y-90375500D01* -X138630639Y-90335474D01* -X138873975Y-90256410D01* -X139101947Y-90140252D01* -X139308942Y-89989862D01* -X139489862Y-89808942D01* -X139640252Y-89601947D01* -X139692425Y-89499553D01* -X140902500Y-89499553D01* -X140902500Y-89657246D01* -X140933261Y-89811889D01* -X140933264Y-89811901D01* -X140993602Y-89957572D01* -X140993609Y-89957585D01* -X141081210Y-90088688D01* -X141081213Y-90088692D01* -X141192707Y-90200186D01* -X141192711Y-90200189D01* -X141323814Y-90287790D01* -X141323827Y-90287797D01* -X141469498Y-90348135D01* -X141469503Y-90348137D01* -X141604552Y-90375000D01* -X141624153Y-90378899D01* -X141624156Y-90378900D01* -X141624158Y-90378900D01* -X141781844Y-90378900D01* -X141781845Y-90378899D01* -X141936497Y-90348137D01* -X142082179Y-90287794D01* -X142213289Y-90200189D01* -X142324789Y-90088689D01* -X142412394Y-89957579D01* -X142472737Y-89811897D01* -X142503500Y-89657242D01* -X142503500Y-89499558D01* -X142503500Y-89499555D01* -X142503499Y-89499553D01* -X142491090Y-89437171D01* -X142472737Y-89344903D01* -X142455740Y-89303868D01* -X142412397Y-89199227D01* -X142412390Y-89199214D01* -X142324789Y-89068111D01* -X142324786Y-89068107D01* -X142213292Y-88956613D01* -X142213288Y-88956610D01* -X142082185Y-88869009D01* -X142082172Y-88869002D01* -X141936501Y-88808664D01* -X141936489Y-88808661D01* -X141781845Y-88777900D01* -X141781842Y-88777900D01* -X141624158Y-88777900D01* -X141624155Y-88777900D01* -X141469510Y-88808661D01* -X141469498Y-88808664D01* -X141323827Y-88869002D01* -X141323814Y-88869009D01* -X141192711Y-88956610D01* -X141192707Y-88956613D01* -X141081213Y-89068107D01* -X141081210Y-89068111D01* -X140993609Y-89199214D01* -X140993602Y-89199227D01* -X140933264Y-89344898D01* -X140933261Y-89344910D01* -X140902500Y-89499553D01* -X139692425Y-89499553D01* -X139756410Y-89373975D01* -X139835474Y-89130639D01* -X139875500Y-88877930D01* -X139875500Y-88622070D01* -X139835474Y-88369361D01* -X139756410Y-88126025D01* -X139756410Y-88126024D01* -X139699580Y-88014490D01* -X139640252Y-87898053D01* -X139580196Y-87815392D01* -X139489867Y-87691064D01* -X139489863Y-87691059D01* -X139308940Y-87510136D01* -X139308935Y-87510132D01* -X139101950Y-87359750D01* -X139101949Y-87359749D01* -X139101947Y-87359748D01* -X139004290Y-87309989D01* -X138873975Y-87243589D01* -X138873972Y-87243588D01* -X138630640Y-87164526D01* -X138504284Y-87144513D01* -X138377930Y-87124500D01* -X138122070Y-87124500D01* -X138037833Y-87137842D01* -X137869359Y-87164526D01* -X137626027Y-87243588D01* -X137626024Y-87243589D01* -X137398049Y-87359750D01* -X137191064Y-87510132D01* -X137191059Y-87510136D01* -X137010136Y-87691059D01* -X137010132Y-87691064D01* -X136859750Y-87898049D01* -X136743589Y-88126024D01* -X136743588Y-88126027D01* -X136664526Y-88369359D01* -X136660236Y-88396446D01* -X136624500Y-88622070D01* -X133374994Y-88622070D01* -X133334986Y-88369476D01* -X133255948Y-88126218D01* -X133255947Y-88126215D01* -X133139824Y-87898313D01* -X133062148Y-87791403D01* -X133062148Y-87791402D01* -X132331907Y-88521645D01* -X132303868Y-88453952D01* -X132235469Y-88351586D01* -X132148414Y-88264531D01* -X132046048Y-88196132D01* -X131978353Y-88168092D01* -X132621796Y-87524650D01* -X132683119Y-87491165D01* -X132697331Y-87488927D01* -X132699633Y-87488700D01* -X132699642Y-87488700D01* -X132699651Y-87488698D01* -X132699653Y-87488698D01* -X132736964Y-87481275D01* -X132854297Y-87457937D01* -X132999979Y-87397594D01* -X133117135Y-87319312D01* -X133183809Y-87298436D01* -X133251189Y-87316920D01* -X133297880Y-87368899D01* -X133307640Y-87398224D01* -X133335561Y-87538591D01* -X133335564Y-87538601D01* -X133395902Y-87684272D01* -X133395909Y-87684285D01* -X133483510Y-87815388D01* -X133483513Y-87815392D01* -X133595007Y-87926886D01* -X133595011Y-87926889D01* -X133726114Y-88014490D01* -X133726127Y-88014497D01* -X133871798Y-88074835D01* -X133871803Y-88074837D01* -X134026453Y-88105599D01* -X134026456Y-88105600D01* -X134026458Y-88105600D01* -X134184144Y-88105600D01* -X134184145Y-88105599D01* -X134338797Y-88074837D01* -X134484479Y-88014494D01* -X134615589Y-87926889D01* -X134727089Y-87815389D01* -X134814694Y-87684279D01* -X134875037Y-87538597D01* -X134905800Y-87383942D01* -X134905800Y-87226258D01* -X134905800Y-87226255D01* -X134905799Y-87226253D01* -X134900276Y-87198489D01* -X134875037Y-87071603D01* -X134826137Y-86953547D01* -X134814697Y-86925927D01* -X134814690Y-86925914D01* -X134727089Y-86794811D01* -X134727086Y-86794807D01* -X134615592Y-86683313D01* -X134615588Y-86683310D01* -X134484485Y-86595709D01* -X134484472Y-86595702D01* -X134338801Y-86535364D01* -X134338789Y-86535361D01* -X134184145Y-86504600D01* -X134184142Y-86504600D01* -X134026458Y-86504600D01* -X134026455Y-86504600D01* -X133871810Y-86535361D01* -X133871798Y-86535364D01* -X133726127Y-86595702D01* -X133726114Y-86595709D01* -X133608967Y-86673985D01* -X133542289Y-86694863D01* -X133474909Y-86676378D01* -X133428219Y-86624399D01* -X133418459Y-86595074D01* -X133390538Y-86454710D01* -X133390537Y-86454703D01* -X133337224Y-86325992D01* -X133330197Y-86309027D01* -X133330190Y-86309014D01* -X133242589Y-86177911D01* -X133242586Y-86177907D01* -X133131092Y-86066413D01* -X133131088Y-86066410D01* -X132999985Y-85978809D01* -X132999972Y-85978802D01* -X132854301Y-85918464D01* -X132854289Y-85918461D01* -X132699645Y-85887700D01* -X132699642Y-85887700D01* -X132632801Y-85887700D01* -X132565762Y-85868015D01* -X132520007Y-85815211D01* -X132510063Y-85746053D01* -X132539088Y-85682497D01* -X132576505Y-85653216D01* -X132590522Y-85646073D01* +X131126024Y-85756410D01* +X131126027Y-85756411D01* +X131228503Y-85789707D01* +X131369361Y-85835474D01* +X131622070Y-85875500D01* +X131622071Y-85875500D01* +X131877929Y-85875500D01* +X131877930Y-85875500D01* +X132130639Y-85835474D01* +X132373975Y-85756410D01* X132601947Y-85640252D01* X132808942Y-85489862D01* X132989862Y-85308942D01* @@ -4709,12 +5349,12 @@ X137010132Y-85308935D01* X137010136Y-85308940D01* X137191059Y-85489863D01* X137191064Y-85489867D01* -X137318167Y-85582212D01* +X137282095Y-85556004D01* X137398053Y-85640252D01* X137547080Y-85716185D01* X137626024Y-85756410D01* X137626027Y-85756411D01* -X137747693Y-85795942D01* +X137728503Y-85789707D01* X137869361Y-85835474D01* X138122070Y-85875500D01* X138122071Y-85875500D01* @@ -4749,169 +5389,12 @@ X141441365Y-85275500D01* X141441372Y-85275500D01* X141672126Y-85245121D01* X141896940Y-85184882D01* -X141954953Y-85160852D01* +X142097165Y-85101947D01* X142111960Y-85095819D01* X142111963Y-85095817D01* X142111969Y-85095815D01* X142313532Y-84979442D01* X142498181Y-84837756D01* -X142645584Y-84690353D01* -X145004200Y-84690353D01* -X145004200Y-84848046D01* -X145034961Y-85002689D01* -X145034964Y-85002701D01* -X145095302Y-85148372D01* -X145095309Y-85148385D01* -X145182910Y-85279488D01* -X145182913Y-85279492D01* -X145232822Y-85329401D01* -X145266307Y-85390724D01* -X145261323Y-85460416D01* -X145259702Y-85464534D01* -X145210964Y-85582198D01* -X145210961Y-85582210D01* -X145180200Y-85736853D01* -X145180200Y-85894546D01* -X145210961Y-86049189D01* -X145210964Y-86049201D01* -X145271302Y-86194872D01* -X145271309Y-86194885D01* -X145358910Y-86325988D01* -X145358913Y-86325992D01* -X145470407Y-86437486D01* -X145470411Y-86437489D01* -X145601514Y-86525090D01* -X145601527Y-86525097D01* -X145747198Y-86585435D01* -X145747203Y-86585437D01* -X145901853Y-86616199D01* -X145901856Y-86616200D01* -X145901858Y-86616200D01* -X146059544Y-86616200D01* -X146059545Y-86616199D01* -X146214197Y-86585437D01* -X146359879Y-86525094D01* -X146490989Y-86437489D01* -X146602489Y-86325989D01* -X146690094Y-86194879D01* -X146750437Y-86049197D01* -X146781200Y-85894542D01* -X146781200Y-85736858D01* -X146781200Y-85736855D01* -X146781199Y-85736853D01* -X146772674Y-85693995D01* -X147499499Y-85693995D01* -X147526418Y-85829322D01* -X147526421Y-85829332D01* -X147579221Y-85956804D01* -X147579228Y-85956817D01* -X147655885Y-86071541D01* -X147655888Y-86071545D01* -X147753454Y-86169111D01* -X147753458Y-86169114D01* -X147868182Y-86245771D01* -X147868195Y-86245778D01* -X147995667Y-86298578D01* -X147995672Y-86298580D01* -X147995676Y-86298580D01* -X147995677Y-86298581D01* -X148131004Y-86325500D01* -X148131007Y-86325500D01* -X148268995Y-86325500D01* -X148360041Y-86307389D01* -X148404328Y-86298580D01* -X148531811Y-86245775D01* -X148646542Y-86169114D01* -X148744114Y-86071542D01* -X148820775Y-85956811D01* -X148873580Y-85829328D01* -X148888084Y-85756411D01* -X148900500Y-85693995D01* -X148900500Y-85556004D01* -X148873581Y-85420677D01* -X148873580Y-85420676D01* -X148873580Y-85420672D01* -X148861175Y-85390724D01* -X148820778Y-85293195D01* -X148820771Y-85293182D01* -X148744114Y-85178458D01* -X148744111Y-85178454D01* -X148646545Y-85080888D01* -X148646541Y-85080885D01* -X148531817Y-85004228D01* -X148531804Y-85004221D01* -X148404332Y-84951421D01* -X148404322Y-84951418D01* -X148268995Y-84924500D01* -X148268993Y-84924500D01* -X148131007Y-84924500D01* -X148131005Y-84924500D01* -X147995677Y-84951418D01* -X147995667Y-84951421D01* -X147868195Y-85004221D01* -X147868182Y-85004228D01* -X147753458Y-85080885D01* -X147753454Y-85080888D01* -X147655888Y-85178454D01* -X147655885Y-85178458D01* -X147579228Y-85293182D01* -X147579221Y-85293195D01* -X147526421Y-85420667D01* -X147526418Y-85420677D01* -X147499500Y-85556004D01* -X147499500Y-85556007D01* -X147499500Y-85693993D01* -X147499500Y-85693995D01* -X147499499Y-85693995D01* -X146772674Y-85693995D01* -X146750439Y-85582212D01* -X146750438Y-85582210D01* -X146750437Y-85582203D01* -X146739585Y-85556004D01* -X146690097Y-85436527D01* -X146690090Y-85436514D01* -X146602489Y-85305411D01* -X146602486Y-85305407D01* -X146552577Y-85255498D01* -X146519092Y-85194175D01* -X146524076Y-85124483D01* -X146525675Y-85120417D01* -X146574437Y-85002697D01* -X146605200Y-84848042D01* -X146605200Y-84690358D01* -X146605200Y-84690355D01* -X146605199Y-84690353D01* -X146574438Y-84535710D01* -X146574437Y-84535703D01* -X146554895Y-84488524D01* -X146514097Y-84390027D01* -X146514090Y-84390014D01* -X146426489Y-84258911D01* -X146426486Y-84258907D01* -X146314992Y-84147413D01* -X146314988Y-84147410D01* -X146183885Y-84059809D01* -X146183872Y-84059802D01* -X146038201Y-83999464D01* -X146038189Y-83999461D01* -X145883545Y-83968700D01* -X145883542Y-83968700D01* -X145725858Y-83968700D01* -X145725855Y-83968700D01* -X145571210Y-83999461D01* -X145571198Y-83999464D01* -X145425527Y-84059802D01* -X145425514Y-84059809D01* -X145294411Y-84147410D01* -X145294407Y-84147413D01* -X145182913Y-84258907D01* -X145182910Y-84258911D01* -X145095309Y-84390014D01* -X145095302Y-84390027D01* -X145034964Y-84535698D01* -X145034961Y-84535710D01* -X145004200Y-84690353D01* -X142645584Y-84690353D01* X142662756Y-84673181D01* X142804442Y-84488532D01* X142920815Y-84286969D01* @@ -4943,7 +5426,7 @@ X144315401Y-82413271D01* X144529274Y-82304296D01* X144617003Y-82240556D01* X144617004Y-82240556D01* -X143879821Y-81503375D01* +X143879822Y-81503375D01* X143932642Y-81489222D01* X144052357Y-81420104D01* X144150104Y-81322357D01* @@ -4985,7 +5468,7 @@ X148900500Y-81306004D01* X148873581Y-81170677D01* X148873580Y-81170676D01* X148873580Y-81170672D01* -X148860456Y-81138988D01* +X148858159Y-81133442D01* X148820778Y-81043195D01* X148820771Y-81043182D01* X148744114Y-80928458D01* @@ -5033,7 +5516,7 @@ X144219222Y-80797358D01* X144150104Y-80677643D01* X144052357Y-80579896D01* X143932642Y-80510778D01* -X143879820Y-80496624D01* +X143879821Y-80496624D01* X144649356Y-79727090D01* X144671825Y-79701345D01* X144723792Y-79663589D01* @@ -5060,37 +5543,19 @@ X145034724Y-76799536D01* X145143736Y-76585589D01* X145217937Y-76357222D01* X145255500Y-76120059D01* -X145255500Y-76091353D01* -X146214300Y-76091353D01* -X146214300Y-76249046D01* -X146245061Y-76403689D01* -X146245064Y-76403701D01* -X146305402Y-76549372D01* -X146305409Y-76549385D01* -X146393010Y-76680488D01* -X146393013Y-76680492D01* -X146504507Y-76791986D01* -X146504511Y-76791989D01* -X146635614Y-76879590D01* -X146635627Y-76879597D01* -X146781298Y-76939935D01* -X146781303Y-76939937D01* -X146935953Y-76970699D01* -X146935956Y-76970700D01* -X146935958Y-76970700D01* -X147093644Y-76970700D01* -X147093645Y-76970699D01* -X147248297Y-76939937D01* -X147393979Y-76879594D01* -X147525089Y-76791989D01* -X147636589Y-76680489D01* -X147724194Y-76549379D01* -X147784537Y-76403697D01* -X147790449Y-76373974D01* -X147822832Y-76312065D01* -X147883548Y-76277490D01* -X147953317Y-76281229D01* -X147959518Y-76283605D01* +X145255500Y-75879941D01* +X145226049Y-75693995D01* +X147499499Y-75693995D01* +X147526418Y-75829322D01* +X147526421Y-75829332D01* +X147579221Y-75956804D01* +X147579228Y-75956817D01* +X147655885Y-76071541D01* +X147655888Y-76071545D01* +X147753454Y-76169111D01* +X147753458Y-76169114D01* +X147868182Y-76245771D01* +X147868195Y-76245778D01* X147995667Y-76298578D01* X147995672Y-76298580D01* X147995676Y-76298580D01* @@ -5111,7 +5576,7 @@ X148900500Y-75556004D01* X148873581Y-75420677D01* X148873580Y-75420676D01* X148873580Y-75420672D01* -X148865209Y-75400463D01* +X148870985Y-75414406D01* X148820778Y-75293195D01* X148820771Y-75293182D01* X148744114Y-75178458D01* @@ -5135,38 +5600,25 @@ X147753454Y-75080888D01* X147655888Y-75178454D01* X147655885Y-75178458D01* X147579228Y-75293182D01* -X147579223Y-75293192D01* -X147540287Y-75387192D01* -X147496446Y-75441595D01* -X147430151Y-75463660D01* -X147378274Y-75454300D01* -X147248301Y-75400464D01* -X147248289Y-75400461D01* -X147093645Y-75369700D01* -X147093642Y-75369700D01* -X146935958Y-75369700D01* -X146935955Y-75369700D01* -X146781310Y-75400461D01* -X146781298Y-75400464D01* -X146635627Y-75460802D01* -X146635614Y-75460809D01* -X146504511Y-75548410D01* -X146504507Y-75548413D01* -X146393013Y-75659907D01* -X146393010Y-75659911D01* -X146305409Y-75791014D01* -X146305402Y-75791027D01* -X146245064Y-75936698D01* -X146245061Y-75936710D01* -X146214300Y-76091353D01* -X145255500Y-76091353D01* -X145255500Y-75879941D01* +X147579221Y-75293195D01* +X147526421Y-75420667D01* +X147526418Y-75420677D01* +X147499500Y-75556004D01* +X147499500Y-75556007D01* +X147499500Y-75693993D01* +X147499500Y-75693995D01* +X147499499Y-75693995D01* +X145226049Y-75693995D01* X145217937Y-75642778D01* +X145217936Y-75642774D01* +X145217936Y-75642773D01* +X145200215Y-75588233D01* +X145145770Y-75420672D01* X145143736Y-75414411D01* X145143734Y-75414408D01* X145143734Y-75414406D01* -X145081973Y-75293195D01* -X145034724Y-75200464D01* +X145034723Y-75200463D01* +X145020267Y-75180566D01* X144893586Y-75006204D01* X144723796Y-74836414D01* X144529536Y-74695276D01* @@ -5199,21 +5651,21 @@ X143009879Y-72928052D01* X142920819Y-72713039D01* X142920811Y-72713023D01* X142804446Y-72511475D01* +X142804443Y-72511470D01* X142804442Y-72511468D01* -X142733630Y-72419184D01* -X142662757Y-72326820D01* +X142662756Y-72326819D01* X142662751Y-72326813D01* X142498186Y-72162248D01* X142498179Y-72162242D01* X142313540Y-72020564D01* -X142313533Y-72020559D01* +X142313538Y-72020562D01* X142313532Y-72020558D01* X142313527Y-72020555D01* X142313524Y-72020553D01* X142111976Y-71904188D01* X142111960Y-71904180D01* X141896947Y-71815120D01* -X141864810Y-71806509D01* +X141729539Y-71770263D01* X141672126Y-71754879D01* X141672125Y-71754878D01* X141672122Y-71754878D01* @@ -5286,7 +5738,6 @@ X142204500Y-76120059D01* X142224412Y-76245778D01* X142242063Y-76357222D01* X142316265Y-76585593D01* -X142421429Y-76791986D01* X142425276Y-76799536D01* X142566414Y-76993796D01* X142566416Y-76993798D01* @@ -5298,25 +5749,50 @@ X142566416Y-77506201D01* X142425276Y-77700463D01* X142316265Y-77914406D01* X142242063Y-78142777D01* -X142204500Y-78379941D01* -X142204500Y-78620058D01* -X142242063Y-78857222D01* -X142316265Y-79085593D01* -X142425276Y-79299536D01* -X142566414Y-79493796D01* -X142736204Y-79663586D01* -X142788174Y-79701344D01* -X142802139Y-79719454D01* -X142802573Y-79719021D01* -X143580177Y-80496624D01* -X143527358Y-80510778D01* -X143407643Y-80579896D01* -X143309896Y-80677643D01* -X143240778Y-80797358D01* -X143226624Y-80850178D01* -X142489442Y-80112995D01* -X142425701Y-80200729D01* -X142316728Y-80414598D01* +X142204499Y-78379943D01* +X142204117Y-78384804D01* +X142201821Y-78384623D01* +X142184815Y-78442539D01* +X142132011Y-78488294D01* +X142080500Y-78499500D01* +X142021155Y-78499500D01* +X141866510Y-78530261D01* +X141866498Y-78530264D01* +X141720827Y-78590602D01* +X141720814Y-78590609D01* +X141589711Y-78678210D01* +X141589707Y-78678213D01* +X141478213Y-78789707D01* +X141478210Y-78789711D01* +X141390609Y-78920814D01* +X141390602Y-78920827D01* +X141330264Y-79066498D01* +X141330261Y-79066510D01* +X141299500Y-79221153D01* +X141299500Y-79378846D01* +X141330261Y-79533489D01* +X141330264Y-79533501D01* +X141390602Y-79679172D01* +X141390609Y-79679185D01* +X141478210Y-79810288D01* +X141478213Y-79810292D01* +X141589707Y-79921786D01* +X141589711Y-79921789D01* +X141720814Y-80009390D01* +X141720827Y-80009397D01* +X141866498Y-80069735D01* +X141866503Y-80069737D01* +X142021153Y-80100499D01* +X142021156Y-80100500D01* +X142021158Y-80100500D01* +X142178843Y-80100500D01* +X142228326Y-80090657D01* +X142259630Y-80084430D01* +X142329221Y-80090657D01* +X142384399Y-80133519D01* +X142407644Y-80199409D01* +X142394307Y-80262341D01* +X142316729Y-80414595D01* X142242549Y-80642894D01* X142205000Y-80879974D01* X142205000Y-81120025D01* @@ -5370,14 +5846,14 @@ X139308935Y-83010132D01* X139101950Y-82859750D01* X139101949Y-82859749D01* X139101947Y-82859748D01* -X139008845Y-82812310D01* +X139028910Y-82822533D01* X138873975Y-82743589D01* X138873972Y-82743588D01* X138630640Y-82664526D01* X138504284Y-82644513D01* X138377930Y-82624500D01* X138122070Y-82624500D01* -X138064616Y-82633600D01* +X138037833Y-82637842D01* X137869359Y-82664526D01* X137626027Y-82743588D01* X137626024Y-82743589D01* @@ -5393,10 +5869,9 @@ X136664526Y-83869359D01* X136624500Y-84122070D01* X133375500Y-84122070D01* X133335474Y-83869361D01* -X133269919Y-83667601D01* -X133256411Y-83626027D01* +X133256410Y-83626025D01* X133256410Y-83626024D01* -X133198791Y-83512942D01* +X133216185Y-83547080D01* X133140252Y-83398053D01* X133061814Y-83290092D01* X132989867Y-83191064D01* @@ -5406,14 +5881,14 @@ X132808935Y-83010132D01* X132601950Y-82859750D01* X132601949Y-82859749D01* X132601947Y-82859748D01* -X132508845Y-82812310D01* +X132528910Y-82822533D01* X132373975Y-82743589D01* X132373972Y-82743588D01* X132130640Y-82664526D01* X132004284Y-82644513D01* X131877930Y-82624500D01* X131622070Y-82624500D01* -X131564616Y-82633600D01* +X131537833Y-82637842D01* X131369359Y-82664526D01* X131126027Y-82743588D01* X131126024Y-82743589D01* @@ -5470,40 +5945,7 @@ X126990120Y-82928052D01* X126929878Y-83152877D01* X126899501Y-83383617D01* X126899500Y-83383634D01* -X125555100Y-83383634D01* -X125555100Y-83355258D01* -X125555100Y-83355255D01* -X125555099Y-83355253D01* -X125524337Y-83200603D01* -X125520383Y-83191058D01* -X125463997Y-83054927D01* -X125463990Y-83054914D01* -X125376389Y-82923811D01* -X125376386Y-82923807D01* -X125264892Y-82812313D01* -X125264888Y-82812310D01* -X125133785Y-82724709D01* -X125133772Y-82724702D01* -X124988101Y-82664364D01* -X124988089Y-82664361D01* -X124833445Y-82633600D01* -X124833442Y-82633600D01* -X124675758Y-82633600D01* -X124675755Y-82633600D01* -X124521110Y-82664361D01* -X124521098Y-82664364D01* -X124375427Y-82724702D01* -X124375414Y-82724709D01* -X124244311Y-82812310D01* -X124244307Y-82812313D01* -X124132813Y-82923807D01* -X124132810Y-82923811D01* -X124045209Y-83054914D01* -X124045202Y-83054927D01* -X123984864Y-83200598D01* -X123984861Y-83200610D01* -X123954100Y-83355253D01* -X120250500Y-83355253D01* +X120250500Y-83383634D01* X120250500Y-81443995D01* X121099499Y-81443995D01* X121126418Y-81579322D01* @@ -5536,7 +5978,7 @@ X122500500Y-81306004D01* X122473581Y-81170677D01* X122473580Y-81170676D01* X122473580Y-81170672D01* -X122460456Y-81138988D01* +X122458159Y-81133442D01* X122420778Y-81043195D01* X122420771Y-81043182D01* X122344114Y-80928458D01* @@ -5569,68 +6011,6 @@ X121099500Y-81443993D01* X121099500Y-81443995D01* X121099499Y-81443995D01* X120250500Y-81443995D01* -X120250500Y-80549853D01* -X125892000Y-80549853D01* -X125892000Y-80707546D01* -X125922761Y-80862189D01* -X125922764Y-80862201D01* -X125983102Y-81007872D01* -X125983109Y-81007885D01* -X126070710Y-81138988D01* -X126070713Y-81138992D01* -X126182207Y-81250486D01* -X126182211Y-81250489D01* -X126313314Y-81338090D01* -X126313327Y-81338097D01* -X126458998Y-81398435D01* -X126459003Y-81398437D01* -X126567930Y-81420104D01* -X126613653Y-81429199D01* -X126613656Y-81429200D01* -X126613658Y-81429200D01* -X126771344Y-81429200D01* -X126771345Y-81429199D01* -X126925997Y-81398437D01* -X127071679Y-81338094D01* -X127202789Y-81250489D01* -X127314289Y-81138989D01* -X127401894Y-81007879D01* -X127462237Y-80862197D01* -X127493000Y-80707542D01* -X127493000Y-80549858D01* -X127493000Y-80549855D01* -X127492999Y-80549853D01* -X127462238Y-80395210D01* -X127462237Y-80395203D01* -X127462235Y-80395198D01* -X127401897Y-80249527D01* -X127401890Y-80249514D01* -X127314289Y-80118411D01* -X127314286Y-80118407D01* -X127202792Y-80006913D01* -X127202788Y-80006910D01* -X127071685Y-79919309D01* -X127071672Y-79919302D01* -X126926001Y-79858964D01* -X126925989Y-79858961D01* -X126771345Y-79828200D01* -X126771342Y-79828200D01* -X126613658Y-79828200D01* -X126613655Y-79828200D01* -X126459010Y-79858961D01* -X126458998Y-79858964D01* -X126313327Y-79919302D01* -X126313314Y-79919309D01* -X126182211Y-80006910D01* -X126182207Y-80006913D01* -X126070713Y-80118407D01* -X126070710Y-80118411D01* -X125983109Y-80249514D01* -X125983102Y-80249527D01* -X125922764Y-80395198D01* -X125922761Y-80395210D01* -X125892000Y-80549853D01* -X120250500Y-80549853D01* X120250500Y-75693995D01* X121099499Y-75693995D01* X121126418Y-75829322D01* @@ -5643,7 +6023,7 @@ X121353454Y-76169111D01* X121353458Y-76169114D01* X121468182Y-76245771D01* X121468195Y-76245778D01* -X121559519Y-76283605D01* +X121595667Y-76298578D01* X121595672Y-76298580D01* X121595676Y-76298580D01* X121595677Y-76298581D01* @@ -5663,7 +6043,7 @@ X122500500Y-75556004D01* X122473581Y-75420677D01* X122473580Y-75420676D01* X122473580Y-75420672D01* -X122465209Y-75400463D01* +X122470985Y-75414406D01* X122420778Y-75293195D01* X122420771Y-75293182D01* X122344114Y-75178458D01* @@ -5741,43 +6121,10 @@ X130420121Y-73152874D01* X130359882Y-72928060D01* X130359879Y-72928052D01* X130270819Y-72713039D01* -X130270811Y-72713023D01* -X130154446Y-72511475D01* +X130270814Y-72713030D01* +X130216435Y-72618843D01* X130154442Y-72511468D01* -X130083630Y-72419184D01* -X130012757Y-72326820D01* -X130012751Y-72326813D01* -X129848186Y-72162248D01* -X129848179Y-72162242D01* -X129706396Y-72053449D01* -X129663532Y-72020558D01* -X129663526Y-72020554D01* -X129663524Y-72020553D01* -X129560640Y-71961152D01* -X130334499Y-71961152D01* -X130334499Y-72118845D01* -X130365260Y-72273488D01* -X130365263Y-72273500D01* -X130425601Y-72419171D01* -X130425608Y-72419184D01* -X130513209Y-72550287D01* -X130513212Y-72550291D01* -X130624706Y-72661785D01* -X130624710Y-72661788D01* -X130755813Y-72749389D01* -X130755826Y-72749396D01* -X130901497Y-72809734D01* -X130901502Y-72809736D01* -X131056152Y-72840498D01* -X131056155Y-72840499D01* -X131056157Y-72840499D01* -X131213843Y-72840499D01* -X131213844Y-72840498D01* -X131368496Y-72809736D01* -X131514178Y-72749393D01* -X131645288Y-72661788D01* -X131756788Y-72550288D01* -X131816347Y-72461152D01* +X130115833Y-72461152D01* X137684500Y-72461152D01* X137684500Y-72618845D01* X137715261Y-72773488D01* @@ -5798,10 +6145,6 @@ X138406158Y-73340499D01* X138563844Y-73340499D01* X138563845Y-73340498D01* X138718497Y-73309736D01* -X138761911Y-73291753D01* -X138826482Y-73265008D01* -X138864172Y-73249396D01* -X138864172Y-73249395D01* X138864179Y-73249393D01* X138995289Y-73161788D01* X139106789Y-73050288D01* @@ -5811,9 +6154,8 @@ X139285500Y-72618841D01* X139285500Y-72461157D01* X139285500Y-72461154D01* X139285499Y-72461152D01* -X139274849Y-72407610D01* X139254737Y-72306502D01* -X139241062Y-72273488D01* +X139254735Y-72306497D01* X139194397Y-72160826D01* X139194390Y-72160813D01* X139106789Y-72029710D01* @@ -5841,21 +6183,75 @@ X137775602Y-72160826D01* X137715264Y-72306497D01* X137715261Y-72306509D01* X137684500Y-72461152D01* -X131816347Y-72461152D01* -X131844393Y-72419178D01* -X131904736Y-72273496D01* -X131935499Y-72118841D01* -X131935499Y-71961157D01* -X131935499Y-71961154D01* -X131935498Y-71961152D01* -X131909530Y-71830605D01* -X131904736Y-71806502D01* -X131900220Y-71795599D01* -X131844396Y-71660826D01* -X131844389Y-71660813D01* -X131756788Y-71529710D01* -X131756785Y-71529706D01* -X131671074Y-71443995D01* +X130115833Y-72461152D01* +X130012756Y-72326819D01* +X130012751Y-72326813D01* +X129848186Y-72162248D01* +X129848179Y-72162242D01* +X129663540Y-72020564D01* +X129663538Y-72020562D01* +X129663532Y-72020558D01* +X129663527Y-72020555D01* +X129663524Y-72020553D01* +X129461976Y-71904188D01* +X129461960Y-71904180D01* +X129246947Y-71815120D01* +X129079539Y-71770263D01* +X129022126Y-71754879D01* +X129022125Y-71754878D01* +X129022122Y-71754878D01* +X128791382Y-71724501D01* +X128791377Y-71724500D01* +X128791372Y-71724500D01* +X128558628Y-71724500D01* +X128558622Y-71724500D01* +X128558617Y-71724501D01* +X128327877Y-71754878D01* +X128103052Y-71815120D01* +X127888039Y-71904180D01* +X127888023Y-71904188D01* +X127686475Y-72020553D01* +X127686459Y-72020564D01* +X127501820Y-72162242D01* +X127501813Y-72162248D01* +X127337248Y-72326813D01* +X127337242Y-72326820D01* +X127195564Y-72511459D01* +X127195553Y-72511475D01* +X127079188Y-72713023D01* +X127079180Y-72713039D01* +X126990120Y-72928052D01* +X126929878Y-73152877D01* +X126899501Y-73383617D01* +X126899500Y-73383634D01* +X120250500Y-73383634D01* +X120250500Y-71443995D01* +X121099499Y-71443995D01* +X121126418Y-71579322D01* +X121126421Y-71579332D01* +X121179221Y-71706804D01* +X121179228Y-71706817D01* +X121255885Y-71821541D01* +X121255888Y-71821545D01* +X121353454Y-71919111D01* +X121353458Y-71919114D01* +X121468182Y-71995771D01* +X121468195Y-71995778D01* +X121595667Y-72048578D01* +X121595672Y-72048580D01* +X121595676Y-72048580D01* +X121595677Y-72048581D01* +X121731004Y-72075500D01* +X121731007Y-72075500D01* +X121868995Y-72075500D01* +X121960041Y-72057389D01* +X122004328Y-72048580D01* +X122131811Y-71995775D01* +X122246542Y-71919114D01* +X122344114Y-71821542D01* +X122420775Y-71706811D01* +X122473580Y-71579328D01* +X122500500Y-71443995D01* X147499499Y-71443995D01* X147526418Y-71579322D01* X147526421Y-71579332D01* @@ -5874,17 +6270,15 @@ X147995677Y-72048581D01* X148131004Y-72075500D01* X148131007Y-72075500D01* X148268995Y-72075500D01* -X148379890Y-72053441D01* +X148360041Y-72057389D01* X148404328Y-72048580D01* X148531811Y-71995775D01* X148646542Y-71919114D01* X148744114Y-71821542D01* X148820775Y-71706811D01* -X148821734Y-71704497D01* -X148832740Y-71677924D01* X148873580Y-71579328D01* -X148888287Y-71505392D01* -X148900500Y-71443995D01* +X148900500Y-71443993D01* +X148900500Y-71306007D01* X148900500Y-71306004D01* X148873581Y-71170677D01* X148873580Y-71170676D01* @@ -5921,93 +6315,9 @@ X147499500Y-71306007D01* X147499500Y-71443993D01* X147499500Y-71443995D01* X147499499Y-71443995D01* -X131671074Y-71443995D01* -X131645291Y-71418212D01* -X131645287Y-71418209D01* -X131514184Y-71330608D01* -X131514171Y-71330601D01* -X131368500Y-71270263D01* -X131368488Y-71270260D01* -X131213844Y-71239499D01* -X131213841Y-71239499D01* -X131056157Y-71239499D01* -X131056154Y-71239499D01* -X130901509Y-71270260D01* -X130901497Y-71270263D01* -X130755826Y-71330601D01* -X130755813Y-71330608D01* -X130624710Y-71418209D01* -X130624706Y-71418212D01* -X130513212Y-71529706D01* -X130513209Y-71529710D01* -X130425608Y-71660813D01* -X130425601Y-71660826D01* -X130365263Y-71806497D01* -X130365260Y-71806509D01* -X130334499Y-71961152D01* -X129560640Y-71961152D01* -X129461976Y-71904188D01* -X129461960Y-71904180D01* -X129246947Y-71815120D01* -X129214810Y-71806509D01* -X129022126Y-71754879D01* -X129022125Y-71754878D01* -X129022122Y-71754878D01* -X128791382Y-71724501D01* -X128791377Y-71724500D01* -X128791372Y-71724500D01* -X128558628Y-71724500D01* -X128558622Y-71724500D01* -X128558617Y-71724501D01* -X128327877Y-71754878D01* -X128103052Y-71815120D01* -X127888039Y-71904180D01* -X127888023Y-71904188D01* -X127686475Y-72020553D01* -X127686459Y-72020564D01* -X127501820Y-72162242D01* -X127501813Y-72162248D01* -X127337248Y-72326813D01* -X127337242Y-72326820D01* -X127195564Y-72511459D01* -X127195553Y-72511475D01* -X127079188Y-72713023D01* -X127079180Y-72713039D01* -X126990120Y-72928052D01* -X126929878Y-73152877D01* -X126899501Y-73383617D01* -X126899500Y-73383634D01* -X120250500Y-73383634D01* -X120250500Y-71443995D01* -X121099499Y-71443995D01* -X121126418Y-71579322D01* -X121126421Y-71579332D01* -X121179221Y-71706804D01* -X121179228Y-71706817D01* -X121255885Y-71821541D01* -X121255888Y-71821545D01* -X121353454Y-71919111D01* -X121353458Y-71919114D01* -X121468182Y-71995771D01* -X121468195Y-71995778D01* -X121595667Y-72048578D01* -X121595672Y-72048580D01* -X121595676Y-72048580D01* -X121595677Y-72048581D01* -X121731004Y-72075500D01* -X121731007Y-72075500D01* -X121868995Y-72075500D01* -X121979890Y-72053441D01* -X122004328Y-72048580D01* -X122131811Y-71995775D01* -X122246542Y-71919114D01* -X122344114Y-71821542D01* -X122420775Y-71706811D01* -X122421734Y-71704497D01* -X122432740Y-71677924D01* -X122473580Y-71579328D01* -X122488287Y-71505392D01* X122500500Y-71443995D01* +X122500500Y-71443993D01* +X122500500Y-71306007D01* X122500500Y-71306004D01* X122473581Y-71170677D01* X122473580Y-71170676D01* @@ -6015,70 +6325,8 @@ X122473580Y-71170672D01* X122473578Y-71170667D01* X122420778Y-71043195D01* X122420771Y-71043182D01* -X122377924Y-70979057D01* X122344114Y-70928458D01* X122344111Y-70928454D01* -X122331910Y-70916253D01* -X125203400Y-70916253D01* -X125203400Y-71073946D01* -X125234161Y-71228589D01* -X125234164Y-71228601D01* -X125294502Y-71374272D01* -X125294509Y-71374285D01* -X125382110Y-71505388D01* -X125382113Y-71505392D01* -X125493607Y-71616886D01* -X125493611Y-71616889D01* -X125624714Y-71704490D01* -X125624727Y-71704497D01* -X125746362Y-71754879D01* -X125770403Y-71764837D01* -X125925053Y-71795599D01* -X125925056Y-71795600D01* -X125925058Y-71795600D01* -X126082744Y-71795600D01* -X126082745Y-71795599D01* -X126237397Y-71764837D01* -X126383079Y-71704494D01* -X126514189Y-71616889D01* -X126625689Y-71505389D01* -X126713294Y-71374279D01* -X126773637Y-71228597D01* -X126804400Y-71073942D01* -X126804400Y-70916258D01* -X126804400Y-70916255D01* -X126804399Y-70916253D01* -X126774325Y-70765063D01* -X126773637Y-70761603D01* -X126725280Y-70644857D01* -X126713297Y-70615927D01* -X126713290Y-70615914D01* -X126625689Y-70484811D01* -X126625686Y-70484807D01* -X126514192Y-70373313D01* -X126514188Y-70373310D01* -X126383085Y-70285709D01* -X126383072Y-70285702D01* -X126237401Y-70225364D01* -X126237389Y-70225361D01* -X126082745Y-70194600D01* -X126082742Y-70194600D01* -X125925058Y-70194600D01* -X125925055Y-70194600D01* -X125770410Y-70225361D01* -X125770398Y-70225364D01* -X125624727Y-70285702D01* -X125624714Y-70285709D01* -X125493611Y-70373310D01* -X125493607Y-70373313D01* -X125382113Y-70484807D01* -X125382110Y-70484811D01* -X125294509Y-70615914D01* -X125294502Y-70615927D01* -X125234164Y-70761598D01* -X125234161Y-70761610D01* -X125203400Y-70916253D01* -X122331910Y-70916253D01* X122246545Y-70830888D01* X122246541Y-70830885D01* X122131817Y-70754228D01* @@ -6112,7 +6360,7 @@ X130974500Y-69649941D01* X130974500Y-69890058D01* X131012063Y-70127222D01* X131086265Y-70355593D01* -X131152104Y-70484807D01* +X131195143Y-70569274D01* X131195276Y-70569536D01* X131336414Y-70763796D01* X131506204Y-70933586D01* @@ -6251,128 +6499,128 @@ X131086265Y-69184406D01* X131012063Y-69412777D01* X130974500Y-69649941D01* X120250500Y-69649941D01* -X120250500Y-66773453D01* -X126460200Y-66773453D01* -X126460200Y-66931146D01* -X126490961Y-67085789D01* -X126490964Y-67085801D01* -X126551302Y-67231472D01* -X126551309Y-67231485D01* -X126638910Y-67362588D01* -X126638913Y-67362592D01* -X126750407Y-67474086D01* -X126750411Y-67474089D01* -X126881514Y-67561690D01* -X126881527Y-67561697D01* -X127027198Y-67622035D01* -X127027203Y-67622037D01* -X127181853Y-67652799D01* -X127181856Y-67652800D01* -X127181858Y-67652800D01* -X127339544Y-67652800D01* -X127339545Y-67652799D01* -X127494197Y-67622037D01* -X127639879Y-67561694D01* -X127770989Y-67474089D01* -X127882489Y-67362589D01* -X127970094Y-67231479D01* -X128030437Y-67085797D01* -X128061200Y-66931142D01* -X128061200Y-66773458D01* -X128061200Y-66773455D01* -X128061199Y-66773453D01* -X128030438Y-66618810D01* -X128030437Y-66618803D01* -X128030435Y-66618798D01* -X127970097Y-66473127D01* -X127970090Y-66473114D01* -X127882489Y-66342011D01* -X127882486Y-66342007D01* -X127770992Y-66230513D01* -X127770988Y-66230510D01* -X127639885Y-66142909D01* -X127639872Y-66142902D01* -X127494201Y-66082564D01* -X127494189Y-66082561D01* -X127339545Y-66051800D01* -X127339542Y-66051800D01* -X127181858Y-66051800D01* -X127181855Y-66051800D01* -X127027210Y-66082561D01* -X127027198Y-66082564D01* -X126881527Y-66142902D01* -X126881514Y-66142909D01* -X126750411Y-66230510D01* -X126750407Y-66230513D01* -X126638913Y-66342007D01* -X126638910Y-66342011D01* -X126551309Y-66473114D01* -X126551302Y-66473127D01* -X126490964Y-66618798D01* -X126490961Y-66618810D01* -X126460200Y-66773453D01* -X120250500Y-66773453D01* -X120250500Y-65573253D01* -X131454300Y-65573253D01* -X131454300Y-65730946D01* -X131485061Y-65885589D01* -X131485064Y-65885601D01* -X131545402Y-66031272D01* -X131545409Y-66031285D01* -X131633010Y-66162388D01* -X131633013Y-66162392D01* -X131744507Y-66273886D01* -X131744511Y-66273889D01* -X131875614Y-66361490D01* -X131875627Y-66361497D01* -X132021298Y-66421835D01* -X132021303Y-66421837D01* -X132175953Y-66452599D01* -X132175956Y-66452600D01* -X132175958Y-66452600D01* -X132333644Y-66452600D01* -X132333645Y-66452599D01* -X132488297Y-66421837D01* -X132633979Y-66361494D01* -X132765089Y-66273889D01* -X132876589Y-66162389D01* -X132964194Y-66031279D01* -X133024537Y-65885597D01* -X133055300Y-65730942D01* -X133055300Y-65573258D01* -X133055300Y-65573255D01* -X133055299Y-65573253D01* -X133024538Y-65418610D01* -X133024537Y-65418603D01* -X133024535Y-65418598D01* -X132964197Y-65272927D01* -X132964190Y-65272914D01* -X132876589Y-65141811D01* -X132876586Y-65141807D01* -X132765092Y-65030313D01* -X132765088Y-65030310D01* -X132633985Y-64942709D01* -X132633972Y-64942702D01* -X132488301Y-64882364D01* -X132488289Y-64882361D01* -X132333645Y-64851600D01* -X132333642Y-64851600D01* -X132175958Y-64851600D01* -X132175955Y-64851600D01* -X132021310Y-64882361D01* -X132021298Y-64882364D01* -X131875627Y-64942702D01* -X131875614Y-64942709D01* -X131744511Y-65030310D01* -X131744507Y-65030313D01* -X131633013Y-65141807D01* -X131633010Y-65141811D01* -X131545409Y-65272914D01* -X131545402Y-65272927D01* -X131485064Y-65418598D01* -X131485061Y-65418610D01* -X131454300Y-65573253D01* -X120250500Y-65573253D01* +X120250500Y-67721153D01* +X123699500Y-67721153D01* +X123699500Y-67878846D01* +X123730261Y-68033489D01* +X123730264Y-68033501D01* +X123790602Y-68179172D01* +X123790609Y-68179185D01* +X123878210Y-68310288D01* +X123878213Y-68310292D01* +X123989707Y-68421786D01* +X123989711Y-68421789D01* +X124120814Y-68509390D01* +X124120827Y-68509397D01* +X124266498Y-68569735D01* +X124266503Y-68569737D01* +X124421153Y-68600499D01* +X124421156Y-68600500D01* +X124421158Y-68600500D01* +X124578844Y-68600500D01* +X124578845Y-68600499D01* +X124733497Y-68569737D01* +X124879179Y-68509394D01* +X125010289Y-68421789D01* +X125121789Y-68310289D01* +X125209394Y-68179179D01* +X125269737Y-68033497D01* +X125300500Y-67878842D01* +X125300500Y-67721158D01* +X125300500Y-67721155D01* +X125300499Y-67721153D01* +X125269738Y-67566510D01* +X125269737Y-67566503D01* +X125269735Y-67566498D01* +X125209397Y-67420827D01* +X125209390Y-67420814D01* +X125121789Y-67289711D01* +X125121786Y-67289707D01* +X125010292Y-67178213D01* +X125010288Y-67178210D01* +X124879185Y-67090609D01* +X124879172Y-67090602D01* +X124733501Y-67030264D01* +X124733489Y-67030261D01* +X124578845Y-66999500D01* +X124578842Y-66999500D01* +X124421158Y-66999500D01* +X124421155Y-66999500D01* +X124266510Y-67030261D01* +X124266498Y-67030264D01* +X124120827Y-67090602D01* +X124120814Y-67090609D01* +X123989711Y-67178210D01* +X123989707Y-67178213D01* +X123878213Y-67289707D01* +X123878210Y-67289711D01* +X123790609Y-67420814D01* +X123790602Y-67420827D01* +X123730264Y-67566498D01* +X123730261Y-67566510D01* +X123699500Y-67721153D01* +X120250500Y-67721153D01* +X120250500Y-64521153D01* +X128199500Y-64521153D01* +X128199500Y-64678846D01* +X128230261Y-64833489D01* +X128230264Y-64833501D01* +X128290602Y-64979172D01* +X128290609Y-64979185D01* +X128378210Y-65110288D01* +X128378213Y-65110292D01* +X128489707Y-65221786D01* +X128489711Y-65221789D01* +X128620814Y-65309390D01* +X128620827Y-65309397D01* +X128766498Y-65369735D01* +X128766503Y-65369737D01* +X128921153Y-65400499D01* +X128921156Y-65400500D01* +X128921158Y-65400500D01* +X129078844Y-65400500D01* +X129078845Y-65400499D01* +X129233497Y-65369737D01* +X129379179Y-65309394D01* +X129510289Y-65221789D01* +X129621789Y-65110289D01* +X129709394Y-64979179D01* +X129769737Y-64833497D01* +X129800500Y-64678842D01* +X129800500Y-64521158D01* +X129800500Y-64521155D01* +X129800499Y-64521153D01* +X129769738Y-64366510D01* +X129769737Y-64366503D01* +X129769735Y-64366498D01* +X129709397Y-64220827D01* +X129709390Y-64220814D01* +X129621789Y-64089711D01* +X129621786Y-64089707D01* +X129510292Y-63978213D01* +X129510288Y-63978210D01* +X129379185Y-63890609D01* +X129379172Y-63890602D01* +X129233501Y-63830264D01* +X129233489Y-63830261D01* +X129078845Y-63799500D01* +X129078842Y-63799500D01* +X128921158Y-63799500D01* +X128921155Y-63799500D01* +X128766510Y-63830261D01* +X128766498Y-63830264D01* +X128620827Y-63890602D01* +X128620814Y-63890609D01* +X128489711Y-63978210D01* +X128489707Y-63978213D01* +X128378213Y-64089707D01* +X128378210Y-64089711D01* +X128290609Y-64220814D01* +X128290602Y-64220827D01* +X128230264Y-64366498D01* +X128230261Y-64366510D01* +X128199500Y-64521153D01* +X120250500Y-64521153D01* X120250500Y-62493713D01* X121149500Y-62493713D01* X121149500Y-62706287D01* @@ -6407,9 +6655,37 @@ X123655051Y-63307816D01* X123751557Y-63118412D01* X123817246Y-62916243D01* X123850500Y-62706287D01* -X123850500Y-62693713D01* +X123850500Y-62621153D01* +X130199500Y-62621153D01* +X130199500Y-62778846D01* +X130230261Y-62933489D01* +X130230264Y-62933501D01* +X130290602Y-63079172D01* +X130290609Y-63079185D01* +X130378210Y-63210288D01* +X130378213Y-63210292D01* +X130489707Y-63321786D01* +X130489711Y-63321789D01* +X130620814Y-63409390D01* +X130620827Y-63409397D01* +X130766498Y-63469735D01* +X130766503Y-63469737D01* +X130921153Y-63500499D01* +X130921156Y-63500500D01* +X130921158Y-63500500D01* +X131078844Y-63500500D01* +X131078845Y-63500499D01* +X131233497Y-63469737D01* +X131379179Y-63409394D01* +X131510289Y-63321789D01* +X131621789Y-63210289D01* +X131709394Y-63079179D01* +X131769737Y-62933497D01* +X131800500Y-62778842D01* +X131800500Y-62693713D01* X146049500Y-62693713D01* -X146049500Y-62906287D01* +X146049500Y-62906286D01* +X146076884Y-63079185D01* X146082754Y-63116243D01* X146145001Y-63307820D01* X146148444Y-63318414D01* @@ -6468,9 +6744,42 @@ X146369890Y-61920213D01* X146244951Y-62092179D01* X146148444Y-62281585D01* X146082753Y-62483760D01* -X146081177Y-62493713D01* X146049500Y-62693713D01* -X123850500Y-62693713D01* +X131800500Y-62693713D01* +X131800500Y-62621158D01* +X131800500Y-62621155D01* +X131800499Y-62621153D01* +X131775149Y-62493713D01* +X131769737Y-62466503D01* +X131750796Y-62420775D01* +X131709397Y-62320827D01* +X131709390Y-62320814D01* +X131621789Y-62189711D01* +X131621786Y-62189707D01* +X131510292Y-62078213D01* +X131510288Y-62078210D01* +X131379185Y-61990609D01* +X131379172Y-61990602D01* +X131233501Y-61930264D01* +X131233489Y-61930261D01* +X131078845Y-61899500D01* +X131078842Y-61899500D01* +X130921158Y-61899500D01* +X130921155Y-61899500D01* +X130766510Y-61930261D01* +X130766498Y-61930264D01* +X130620827Y-61990602D01* +X130620814Y-61990609D01* +X130489711Y-62078210D01* +X130489707Y-62078213D01* +X130378213Y-62189707D01* +X130378210Y-62189711D01* +X130290609Y-62320814D01* +X130290602Y-62320827D01* +X130230264Y-62466498D01* +X130230261Y-62466510D01* +X130199500Y-62621153D01* +X123850500Y-62621153D01* X123850500Y-62493713D01* X123817246Y-62283757D01* X123751557Y-62081588D01* @@ -6487,7 +6796,7 @@ X132428454Y-62344111D01* X132428458Y-62344114D01* X132543182Y-62420771D01* X132543195Y-62420778D01* -X132670667Y-62473578D01* +X132653603Y-62466510D01* X132670672Y-62473580D01* X132670676Y-62473580D01* X132670677Y-62473581D01* @@ -6501,13 +6810,78 @@ X133321542Y-62344114D01* X133419114Y-62246542D01* X133495775Y-62131811D01* X133548580Y-62004328D01* +X133575500Y-61868995D01* +X136424499Y-61868995D01* +X136451418Y-62004322D01* +X136451421Y-62004332D01* +X136504221Y-62131804D01* +X136504228Y-62131817D01* +X136580885Y-62246541D01* +X136580888Y-62246545D01* +X136678454Y-62344111D01* +X136678458Y-62344114D01* +X136793182Y-62420771D01* +X136793195Y-62420778D01* +X136903603Y-62466510D01* +X136920672Y-62473580D01* +X136920676Y-62473580D01* +X136920677Y-62473581D01* +X137056004Y-62500500D01* +X137056007Y-62500500D01* +X137193995Y-62500500D01* +X137285041Y-62482389D01* +X137329328Y-62473580D01* +X137456811Y-62420775D01* +X137571542Y-62344114D01* +X137669114Y-62246542D01* +X137745775Y-62131811D01* +X137798580Y-62004328D01* +X137825500Y-61868993D01* +X137825500Y-61731007D01* +X137825500Y-61731004D01* +X137798581Y-61595677D01* +X137798580Y-61595676D01* +X137798580Y-61595672D01* +X137751808Y-61482753D01* +X137745778Y-61468195D01* +X137745771Y-61468182D01* +X137669114Y-61353458D01* +X137669111Y-61353454D01* +X137571545Y-61255888D01* +X137571541Y-61255885D01* +X137456817Y-61179228D01* +X137456804Y-61179221D01* +X137329332Y-61126421D01* +X137329322Y-61126418D01* +X137193995Y-61099500D01* +X137193993Y-61099500D01* +X137056007Y-61099500D01* +X137056005Y-61099500D01* +X136920677Y-61126418D01* +X136920667Y-61126421D01* +X136793195Y-61179221D01* +X136793182Y-61179228D01* +X136678458Y-61255885D01* +X136678454Y-61255888D01* +X136580888Y-61353454D01* +X136580885Y-61353458D01* +X136504228Y-61468182D01* +X136504221Y-61468195D01* +X136451421Y-61595667D01* +X136451418Y-61595677D01* +X136424500Y-61731004D01* +X136424500Y-61731007D01* +X136424500Y-61868993D01* +X136424500Y-61868995D01* +X136424499Y-61868995D01* +X133575500Y-61868995D01* X133575500Y-61868993D01* X133575500Y-61731007D01* X133575500Y-61731004D01* X133548581Y-61595677D01* X133548580Y-61595676D01* X133548580Y-61595672D01* -X133510029Y-61502601D01* +X133501808Y-61482753D01* X133495778Y-61468195D01* X133495771Y-61468182D01* X133419114Y-61353458D01* @@ -6562,15 +6936,15 @@ X121469890Y-61720213D01* X121344951Y-61892179D01* X121248444Y-62081585D01* X121182753Y-62283760D01* -X121173194Y-62344114D01* +X121152689Y-62473578D01* X121149500Y-62493713D01* X120250500Y-62493713D01* X120250500Y-60374500D01* X120270185Y-60307461D01* X120322989Y-60261706D01* X120374500Y-60250500D01* -X134758628Y-60250500D01* -X134825667Y-60270185D01* +X149625500Y-60250500D01* +X149692539Y-60270185D01* G37* %TD.AperFunction*% %TD*% diff --git a/PCB/v2.x/production/gerbers/snips_controller-NPTH.drl b/PCB/v2.x/production/gerbers/snips_controller-NPTH.drl index 0e76255..1dc4451 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-NPTH.drl +++ b/PCB/v2.x/production/gerbers/snips_controller-NPTH.drl @@ -1,7 +1,7 @@ M48 -; DRILL file KiCad 10.0.5 date 2026-10-30T18:10:02 +; DRILL file KiCad 10.0.5 date 2026-10-31T14:04:15 ; FORMAT={-:-/ absolute / metric / decimal} -; #@! TF.CreationDate,2026-10-30T18:10:02-07:00 +; #@! TF.CreationDate,2026-10-31T14:04:15-07:00 ; #@! TF.GenerationSoftware,Kicad,Pcbnew,10.0.5 ; #@! TF.FileFunction,NonPlated,1,4,NPTH FMAT,2 @@ -11,9 +11,7 @@ T1C0.650 ; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill T2C0.900 ; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill -T3C0.991 -; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill -T4C2.200 +T3C2.200 % G90 G05 @@ -34,10 +32,6 @@ X148.2Y-75.625 X148.2Y-81.375 X148.2Y-85.625 T3 -X145.284Y-109.695 -X146.3Y-114.775 -X147.316Y-109.695 -T4 X122.5Y-62.6 X123.0Y-122.5 X147.0Y-127.0 diff --git a/PCB/v2.x/production/gerbers/snips_controller-PTH.drl b/PCB/v2.x/production/gerbers/snips_controller-PTH.drl index fea4ce3..2d5016c 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-PTH.drl +++ b/PCB/v2.x/production/gerbers/snips_controller-PTH.drl @@ -1,7 +1,7 @@ M48 -; DRILL file KiCad 10.0.5 date 2026-10-30T18:10:02 +; DRILL file KiCad 10.0.5 date 2026-10-31T14:04:15 ; FORMAT={-:-/ absolute / metric / decimal} -; #@! TF.CreationDate,2026-10-30T18:10:02-07:00 +; #@! TF.CreationDate,2026-10-31T14:04:15-07:00 ; #@! TF.GenerationSoftware,Kicad,Pcbnew,10.0.5 ; #@! TF.FileFunction,Plated,1,4,PTH FMAT,2 @@ -24,147 +24,122 @@ T7C1.550 G90 G05 T1 -X129.75Y-117.815 -X129.75Y-118.815 +X128.75Y-95.75 +X128.75Y-96.75 T2 -X120.689Y-97.07 -X121.3Y-107.15 -X121.328Y-96.462 -X121.75Y-119.315 -X122.35Y-105.15 -X122.6Y-124.65 -X122.6Y-125.75 -X123.0Y-104.55 -X123.05Y-95.85 -X123.05Y-103.05 -X123.15Y-85.6 -X123.374Y-117.591 -X123.558Y-90.44 -X123.86Y-116.915 -X123.9Y-113.658 -X123.95Y-73.2 -X123.95Y-83.2 -X124.549Y-107.406 -X124.755Y-83.434 -X124.96Y-104.749 -X125.75Y-118.315 -X125.77Y-125.525 -X126.004Y-70.995 -X126.67Y-93.677 -X126.692Y-80.629 -X126.735Y-100.4 -X127.261Y-66.852 -X127.3Y-121.55 -X127.526Y-92.505 -X127.561Y-90.825 -X128.75Y-103.05 -X128.75Y-124.3 -X129.0Y-96.55 -X129.065Y-94.096 -X129.217Y-123.115 -X129.625Y-98.237 -X129.771Y-116.815 -X129.8Y-64.05 -X129.8Y-100.7 -X129.862Y-101.982 -X129.871Y-119.615 -X129.871Y-99.694 -X130.207Y-95.61 -X130.387Y-96.5 -X130.4Y-126.3 -X130.45Y-67.55 -X130.45Y-103.7 -X130.5Y-92.3 -X130.95Y-107.8 -X131.135Y-72.04 -X131.197Y-105.109 -X131.45Y-117.565 +X120.6Y-125.766 +X121.1Y-124.88 +X121.8Y-96.7 +X121.874Y-107.063 +X121.875Y-124.681 +X121.894Y-106.235 +X122.3Y-87.8 +X122.3Y-102.8 +X122.5Y-125.2 +X122.6Y-104.0 +X122.7Y-114.1 +X123.75Y-95.25 +X123.9Y-98.1 +X124.0Y-119.6 +X124.1Y-83.7 +X124.2Y-64.8 +X124.2Y-71.8 +X124.2Y-111.6 +X124.5Y-67.8 +X124.6Y-109.8 +X124.75Y-96.25 +X124.95Y-104.124 +X125.08Y-124.896 +X125.8Y-109.7 +X126.002Y-123.34 +X126.15Y-97.47 +X126.32Y-106.4 +X126.6Y-100.4 +X126.9Y-123.5 +X127.2Y-127.762 +X127.5Y-99.0 +X127.761Y-93.015 +X127.8Y-117.8 +X128.2Y-105.45 +X128.3Y-97.7 +X128.35Y-95.085 +X128.7Y-100.3 +X129.0Y-64.6 +X129.2Y-123.7 +X129.7Y-93.35 +X130.071Y-92.6 +X130.18Y-120.69 +X130.3Y-116.6 +X130.4Y-109.9 +X130.4Y-117.4 +X130.5Y-110.8 +X130.5Y-114.2 +X130.621Y-129.45 +X130.7Y-63.8 +X130.8Y-106.7 +X130.8Y-108.9 +X130.824Y-108.076 +X130.85Y-97.425 +X131.0Y-62.7 +X131.1Y-101.1 +X131.3Y-117.8 +X131.615Y-118.535 +X131.7Y-115.1 X131.785Y-73.44 -X131.797Y-95.119 -X131.8Y-96.5 -X131.8Y-124.35 -X131.9Y-100.4 -X131.95Y-112.3 -X132.15Y-104.15 -X132.255Y-65.652 -X132.621Y-86.688 -X133.0Y-119.265 -X133.2Y-122.15 -X133.552Y-90.667 -X133.811Y-118.937 -X134.105Y-87.305 -X134.55Y-101.25 -X134.6Y-103.7 -X134.65Y-121.703 -X134.7Y-63.95 -X134.709Y-92.787 -X134.775Y-95.096 -X135.0Y-61.269 -X135.25Y-106.825 -X135.45Y-103.8 -X135.734Y-92.661 -X135.75Y-121.501 -X135.775Y-108.336 -X136.05Y-101.25 -X136.15Y-104.25 -X136.25Y-117.315 -X136.25Y-118.815 +X131.8Y-100.5 +X132.0Y-95.3 +X132.249Y-126.92 +X132.5Y-67.0 +X133.0Y-118.2 +X133.1Y-107.0 +X133.3Y-100.8 +X133.9Y-118.2 +X134.2Y-106.4 +X134.7Y-117.7 +X134.9Y-64.6 +X135.25Y-95.75 +X135.25Y-97.25 +X135.6Y-118.3 +X135.9Y-99.0 +X136.012Y-99.792 +X136.162Y-101.138 X136.285Y-75.94 -X136.3Y-95.3 -X136.4Y-100.4 -X137.05Y-92.15 -X137.4Y-125.8 -X137.45Y-114.3 -X137.85Y-104.15 -X137.902Y-95.242 +X136.5Y-118.3 +X137.0Y-124.9 +X137.4Y-100.2 +X137.5Y-97.75 +X137.8Y-103.0 X138.485Y-72.54 -X138.75Y-126.065 -X139.1Y-103.7 -X139.209Y-100.184 -X139.45Y-121.869 -X139.485Y-96.502 -X139.637Y-97.509 -X139.79Y-98.443 -X139.85Y-87.25 -X140.0Y-69.4 -X140.5Y-108.6 -X140.8Y-122.15 -X141.117Y-110.982 -X141.321Y-92.763 -X141.7Y-70.0 -X141.703Y-89.578 -X141.95Y-79.7 -X142.8Y-95.85 -X142.8Y-103.05 -X142.8Y-126.6 -X142.85Y-95.0 -X142.9Y-67.4 -X143.0Y-92.386 -X143.2Y-90.65 -X143.3Y-102.35 -X143.3Y-106.45 -X143.75Y-70.55 -X144.0Y-94.5 -X144.55Y-69.35 -X144.95Y-110.7 -X145.3Y-75.1 -X145.35Y-93.1 -X145.4Y-103.05 -X145.45Y-95.8 -X145.453Y-98.045 -X145.805Y-84.769 -X145.851Y-107.624 -X145.981Y-85.816 -X146.12Y-98.555 -X146.35Y-66.6 -X146.5Y-67.45 -X147.015Y-76.17 -X147.45Y-102.35 -X147.45Y-106.45 -X148.072Y-111.843 -X148.5Y-73.05 -X148.5Y-83.05 -X149.219Y-96.602 +X138.5Y-93.25 +X138.9Y-106.2 +X139.1Y-70.7 +X139.4Y-116.9 +X139.5Y-94.85 +X139.6Y-114.1 +X139.886Y-98.225 +X139.9Y-106.4 +X140.4Y-100.3 +X140.6Y-118.7 +X140.95Y-90.7 +X141.068Y-104.177 +X141.3Y-106.6 +X142.0Y-107.3 +X142.0Y-114.2 +X142.1Y-79.3 +X142.3Y-124.9 +X142.6Y-102.4 +X144.6Y-86.3 +X144.8Y-90.65 +X144.9Y-108.3 +X145.312Y-107.614 +X145.4Y-88.1 +X145.5Y-117.78 +X145.6Y-73.0 +X146.249Y-83.3 +X147.034Y-98.156 +X147.05Y-96.95 +X147.3Y-109.3 +X147.7Y-98.6 T4 X145.2Y-123.1 X147.2Y-123.1 diff --git a/PCB/v2.x/production/gerbers/snips_controller-job.gbrjob b/PCB/v2.x/production/gerbers/snips_controller-job.gbrjob index 6992ad0..1205626 100644 --- a/PCB/v2.x/production/gerbers/snips_controller-job.gbrjob +++ b/PCB/v2.x/production/gerbers/snips_controller-job.gbrjob @@ -5,7 +5,7 @@ "Application": "Pcbnew", "Version": "10.0.5" }, - "CreationDate": "2026-10-30T18:10:02-07:00" + "CreationDate": "2026-10-31T14:04:15-07:00" }, "GeneralSpecs": { "ProjectId": { @@ -34,7 +34,6 @@ "PadToPad": 0.2, "PadToTrack": 0.2, "TrackToTrack": 0.2, - "MinLineWidth": 0.2, "TrackToRegion": 0.5, "RegionToRegion": 0.5 } diff --git a/PCB/v2.x/production/gerbers/snips_controller.zip b/PCB/v2.x/production/gerbers/snips_controller.zip index 8ec493e..afca23b 100644 Binary files a/PCB/v2.x/production/gerbers/snips_controller.zip and b/PCB/v2.x/production/gerbers/snips_controller.zip differ diff --git a/PCB/v2.x/production/jlcpcb/Snips_2_0.zip b/PCB/v2.x/production/jlcpcb/Snips_2_0.zip index f58e637..362c4f6 100644 Binary files a/PCB/v2.x/production/jlcpcb/Snips_2_0.zip and b/PCB/v2.x/production/jlcpcb/Snips_2_0.zip differ diff --git a/PCB/v2.x/production/jlcpcb/netlist.ipc b/PCB/v2.x/production/jlcpcb/netlist.ipc index c48d218..830dd49 100644 --- a/PCB/v2.x/production/jlcpcb/netlist.ipc +++ b/PCB/v2.x/production/jlcpcb/netlist.ipc @@ -1,167 +1,146 @@ P CODE 00 P UNITS CUST 0 P arrayDim N -317VSYS VIA MD0118PA00X+051628Y-028362X0236Y0000R000S3 -317VSYS VIA MD0118PA00X+052579Y-035696X0236Y0000R000S3 -317VSYS VIA MD0118PA00X+051652Y-041382X0236Y0000R000S3 -317VSYS VIA MD0118PA00X+053455Y-042652X0236Y0000R000S3 -317VSYS VIA MD0118PA00X+050221Y-035758X0236Y0000R000S3 -317GND VIA MD0118PA00X+056693Y-037205X0236Y0000R000S3 -317GND VIA MD0118PA00X+051890Y-048957X0236Y0000R000S3 -317GND VIA MD0118PA00X+051358Y-026594X0236Y0000R000S3 -317GND VIA MD0118PA00X+056594Y-027776X0236Y0000R000S3 -317GND VIA MD0118PA00X+048799Y-032756X0236Y0000R000S3 -317GND VIA MD0118PA00X+047756Y-042185X0236Y0000R000S3 -317GND VIA MD0118PA00X+056220Y-037736X0236Y0000R000S3 -317GND VIA MD0118PA00X+054764Y-040827X0236Y0000R000S3 -317GND VIA MD0118PA00X+048169Y-041398X0236Y0000R000S3 -317GND VIA MD0118PA00X+051890Y-037992X0236Y0000R000S3 -317GND VIA MD0118PA00X+053661Y-037520X0236Y0000R000S3 -317GND VIA MD0118PA00X+047933Y-046974X0236Y0000R000S3 -317GND VIA MD0118PA00X+048268Y-049508X0236Y0000R000S3 -317GND VIA MD0118PA00X+050689Y-048937X0236Y0000R000S3 -317GND VIA MD0118PA00X+048484Y-033701X0236Y0000R000S3 -317GND VIA MD0118PA00X+048445Y-037736X0236Y0000R000S3 -317GND VIA MD0118PA00X+055315Y-042756X0236Y0000R000S3 -317GND VIA MD0118PA00X+050689Y-040571X0236Y0000R000S3 -317GND VIA MD0118PA00X+048268Y-049075X0236Y0000R000S3 -317GND VIA MD0118PA00X+057677Y-026555X0236Y0000R000S3 -317GND VIA MD0118PA00X+053248Y-042057X0236Y0000R000S3 -317GND VIA MD0118PA00X+055433Y-048091X0236Y0000R000S3 -317GND VIA MD0118PA00X+056240Y-037402X0236Y0000R000S3 -317GND VIA MD0118PA00X+053642Y-046187X0236Y0000R000S3 -317GND VIA MD0118PA00X+052992Y-040827X0236Y0000R000S3 -317GND VIA MD0118PA00X+051378Y-036339X0236Y0000R000S3 -317GND VIA MD0118PA00X+051130Y-047093X0236Y0000R000S3 -317GND VIA MD0118PA00X+051752Y-046285X0236Y0000R000S3 -317GND VIA MD0118PA00X+057205Y-029567X0236Y0000R000S3 -317GND VIA MD0118PA00X+053701Y-039528X0236Y0000R000S3 -317GND VIA MD0118PA00X+055118Y-027323X0236Y0000R000S3 -317GND VIA MD0118PA00X+053031Y-025177X0236Y0000R000S3 -317GND VIA MD0118PA00X+053327Y-040866X0236Y0000R000S3 -317GND VIA MD0118PA00X+054272Y-041004X0236Y0000R000S3 -317GND VIA MD0118PA00X+052362Y-046955X0236Y0000R000S3 -317GND VIA MD0118PA00X+050787Y-038012X0236Y0000R000S3 -317GND VIA MD0118PA00X+058465Y-032697X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+050300Y-036620X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+057209Y-042368X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+053548Y-039288X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+051614Y-039803X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+052066Y-049969X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+050079Y-050300X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+049193Y-040994X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+052835Y-041890X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+049244Y-049172X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+048780Y-038622X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+055539Y-041015X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+051426Y-050965X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+050787Y-025433X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+049732Y-041890X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+057283Y-046370X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+054528Y-036713X0236Y0000R000S3 +3173V3 VIA MD0118PA00X+054094Y-039449X0236Y0000R000S3 +317GND VIA MD0118PA00X+055354Y-046732X0236Y0000R000S3 +317GND VIA MD0118PA00X+049961Y-048622X0236Y0000R000S3 +317GND VIA MD0118PA00X+050512Y-038465X0236Y0000R000S3 +317GND VIA MD0118PA00X+050669Y-039488X0236Y0000R000S3 +317GND VIA MD0118PA00X+054961Y-044921X0236Y0000R000S3 +317GND VIA MD0118PA00X+051516Y-038356X0236Y0000R000S3 +317GND VIA MD0118PA00X+051457Y-025118X0236Y0000R000S3 +317GND VIA MD0118PA00X+054764Y-027835X0236Y0000R000S3 +317GND VIA MD0118PA00X+052165Y-026378X0236Y0000R000S3 +317GND VIA MD0118PA00X+057244Y-034685X0236Y0000R000S3 +317GND VIA MD0118PA00X+054134Y-038484X0236Y0000R000S3 +317GND VIA MD0118PA00X+053248Y-038287X0236Y0000R000S3 +317GND VIA MD0118PA00X+048898Y-028268X0236Y0000R000S3 +317GND VIA MD0118PA00X+053110Y-025433X0236Y0000R000S3 +317GND VIA MD0118PA00X+057894Y-038169X0236Y0000R000S3 +317GND VIA MD0118PA00X+057578Y-032795X0236Y0000R000S3 +317GND VIA MD0118PA00X+048898Y-025512X0236Y0000R000S3 +317GND VIA MD0118PA00X+057323Y-028740X0236Y0000R000S3 +317GND VIA MD0118PA00X+049114Y-037894X0236Y0000R000S3 +317GND VIA MD0118PA00X+051693Y-046378X0236Y0000R000S3 +317GND VIA MD0118PA00X+051496Y-042008X0236Y0000R000S3 +317GND VIA MD0118PA00X+048268Y-040945X0236Y0000R000S3 +317GND VIA MD0118PA00X+055906Y-044961X0236Y0000R000S3 +317GND VIA MD0118PA00X+048858Y-032953X0236Y0000R000S3 +317GND VIA MD0118PA00X+055276Y-039488X0236Y0000R000S3 +317GND VIA MD0118PA00X+047953Y-038071X0236Y0000R000S3 +317GND VIA MD0118PA00X+054252Y-040551X0236Y0000R000S3 +317GND VIA MD0118PA00X+053248Y-037697X0236Y0000R000S3 317GND VIA MD0118PA00X+053656Y-029898X0236Y0000R000S3 -317GND VIA MD0118PA00X+056909Y-027303X0236Y0000R000S3 -317GND VIA MD0118PA00X+056417Y-040295X0236Y0000R000S3 -317GND VIA MD0118PA00X+056378Y-035689X0236Y0000R000S3 -317GND VIA MD0118PA00X+052028Y-041004X0236Y0000R000S3 -317GND VIA MD0118PA00X+051358Y-040827X0236Y0000R000S3 -317GND VIA MD0118PA00X+055787Y-027559X0236Y0000R000S3 -317GND VIA MD0118PA00X+054094Y-049528X0236Y0000R000S3 -317GND VIA MD0118PA00X+048799Y-028819X0236Y0000R000S3 -317GND VIA MD0118PA00X+054114Y-045000X0236Y0000R000S3 -317GND VIA MD0118PA00X+051091Y-045990X0236Y0000R000S3 -317GND VIA MD0118PA00X+051929Y-039528X0236Y0000R000S3 -317GND VIA MD0118PA00X+057067Y-043583X0236Y0000R000S3 -317GND VIA MD0118PA00X+058465Y-028760X0236Y0000R000S3 -317GND VIA MD0118PA00X+056417Y-041909X0236Y0000R000S3 -317GND VIA MD0118PA00X+053957Y-036280X0236Y0000R000S3 +317GND VIA MD0118PA00X+051890Y-039567X0236Y0000R000S3 +317GND VIA MD0118PA00X+050531Y-037435X0236Y0000R000S3 +317GND VIA MD0118PA00X+051969Y-037520X0236Y0000R000S3 317GND VIA MD0118PA00X+051884Y-028913X0236Y0000R000S3 -317GND VIA MD0118PA00X+056220Y-040571X0236Y0000R000S3 -317GND VIA MD0118PA00X+053563Y-039862X0236Y0000R000S3 -317GND VIA MD0118PA00X+055886Y-031378X0236Y0000R000S3 -317GND VIA MD0118PA00X+051102Y-025217X0236Y0000R000S3 -317GND VIA MD0118PA00X+055059Y-034350X0236Y0000R000S3 -317GND VIA MD0118PA00X+057224Y-036654X0236Y0000R000S3 -317GND VIA MD0118PA00X+051555Y-042441X0236Y0000R000S3 -317GND VIA MD0118PA00X+056220Y-049843X0236Y0000R000S3 -317GND VIA MD0118PA00X+057618Y-026220X0236Y0000R000S3 -317GND VIA MD0118PA00X+057264Y-037717X0236Y0000R000S3 -317GND VIA MD0118PA00X+052972Y-039862X0236Y0000R000S3 -317GND VIA MD0118PA00X+058051Y-041909X0236Y0000R000S3 -317GND VIA MD0118PA00X+048445Y-040571X0236Y0000R000S3 -317GND VIA MD0118PA00X+053642Y-046778X0236Y0000R000S3 -317GND VIA MD0118PA00X+058051Y-040295X0236Y0000R000S3 -317GND VIA MD0118PA00X+056260Y-026535X0236Y0000R000S3 -317GND VIA MD0118PA00X+057244Y-040571X0236Y0000R000S3 -317GND VIA MD0118PA00X+048425Y-041161X0236Y0000R000S3 -317GND VIA MD0118PA00X+052441Y-048091X0236Y0000R000S3 -317GND VIA MD0118PA00X+051339Y-049724X0236Y0000R000S3 -317GND VIA MD0118PA00X+049508Y-046581X0236Y0000R000S3 -317ECT/BTN_MACRO4 VIA MD0118PA00X+051102Y-039646X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+049516Y-049419X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+053012Y-047914X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+054902Y-047980X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+055638Y-036521X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+055789Y-035267X0236Y0000R000S3 -317VBUS VIA MD0118PA00X+058748Y-038032X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+051949Y-044213X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+050118Y-047854X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+048780Y-044747X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+057528Y-038801X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+049035Y-042286X0236Y0000R000S3 -3173V3 VIA MD0118PA00X+048764Y-046030X0236Y0000R000S3 -317ECT/BTN_MACRO2 VIA MD0118PA00X+051889Y-037448X0236Y0000R000S3 -317ECT/BTN_THR_UP VIA MD0118PA00X+049116Y-032848X0236Y0000R000S3 -317ECT/BTN_THR_UP VIA MD0118PA00X+052213Y-034129X0236Y0000R000S3 -317ECT/BTN_MACRO6 VIA MD0118PA00X+054807Y-039443X0236Y0000R000S3 -317ECT/BTN_MACRO3 VIA MD0118PA00X+055035Y-038757X0236Y0000R000S3 -317ECT/BTN_MACRO1 VIA MD0118PA00X+050813Y-037045X0236Y0000R000S3 -317VBAT VIA MD0118PA00X+052681Y-046826X0236Y0000R000S3 -317MCU_CORE/STAT2 VIA MD0118PA00X+051334Y-037992X0236Y0000R000S3 -317MCU_CORE/STAT1 VIA MD0118PA00X+048573Y-046296X0236Y0000R000S3 -317OMETER/I2C_SDA VIA MD0118PA00X+052069Y-025847X0236Y0000R000S3 -317OMETER/I2C_SDA VIA MD0118PA00X+049197Y-041240X0236Y0000R000S3 -317OMETER/I2C_SCL VIA MD0118PA00X+047767Y-037977X0236Y0000R000S3 -317OMETER/I2C_SCL VIA MD0118PA00X+049608Y-027951X0236Y0000R000S3 -317OMETER/I2C_SCL VIA MD0118PA00X+049896Y-039528X0236Y0000R000S3 -317ECT/BTN_VOL_DN VIA MD0118PA00X+057403Y-033374X0236Y0000R000S3 -317/USB_C/USB_CC1 VIA MD0118PA00X+053445Y-047835X0236Y0000R000S3 -317CU_CORE/USB_DP VIA MD0118PA00X+058296Y-044032X0236Y0000R000S3 -317CU_CORE/USB_DP VIA MD0118PA00X+054915Y-037993X0236Y0000R000S3 -317CU_CORE/USB_DM VIA MD0118PA00X+054292Y-037497X0236Y0000R000S3 -317/USB_C/USB_CC2 VIA MD0118PA00X+054626Y-049632X0236Y0000R000S3 -317U_CORE/STICK_X VIA MD0118PA00X+049870Y-036881X0236Y0000R000S3 -317U_CORE/STICK_Y VIA MD0118PA00X+051263Y-037642X0236Y0000R000S3 -317CU_CORE/3V3_RF VIA MD0118PA00X+056299Y-036372X0236Y0000R000S3 -317CORE/BTN_STICK VIA MD0118PA00X+053035Y-036530X0236Y0000R000S3 -317/PWR_BTN_SENSE VIA MD0118PA00X+057265Y-038600X0236Y0000R000S3 -317/PWR_BTN_SENSE VIA MD0118PA00X+047515Y-038217X0236Y0000R000S3 -317U_CORE/RGB_DIN VIA MD0118PA00X+050873Y-048471X0236Y0000R000S3 -317ECT/BTN_THR_DN VIA MD0118PA00X+048645Y-035606X0236Y0000R000S3 -317ECT/BTN_VOL_UP VIA MD0118PA00X+053439Y-036481X0236Y0000R000S3 -317ER_BUCK/PWR_EN VIA MD0118PA00X+057422Y-042372X0236Y0000R000S3 -317ER_BUCK/PWR_EN VIA MD0118PA00X+057473Y-033786X0236Y0000R000S3 -317ER_BUCK/PWR_EN VIA MD0118PA00X+055558Y-043694X0236Y0000R000S3 -317ECT/BTN_MACRO5 VIA MD0118PA00X+053602Y-041043X0236Y0000R000S3 -317IGGER/TRIG_ADC VIA MD0118PA00X+050207Y-036419X0236Y0000R000S3 -317IGGER/TRIG_ADC VIA MD0118PA00X+051127Y-040150X0236Y0000R000S3 -317ACCEL_INT1 VIA MD0118PA00X+051130Y-039249X0236Y0000R000S3 -317ACCEL_INT1 VIA MD0118PA00X+054975Y-038389X0236Y0000R000S3 -317ACCEL_INT1 VIA MD0118PA00X+057880Y-029988X0236Y0000R000S3 -317T/BTN_TRIG_DIG VIA MD0118PA00X+053061Y-037440X0236Y0000R000S3 -317T/BTN_TRIG_DIG VIA MD0118PA00X+053150Y-024122X0236Y0000R000S3 -317T/BTN_TRIG_DIG VIA MD0118PA00X+052797Y-034372X0236Y0000R000S3 +317GND VIA MD0118PA00X+048228Y-049291X0236Y0000R000S3 +317_CORE/MCU_BOOT VIA MD0118PA00X+055079Y-041890X0236Y0000R000S3 +317_CORE/MCU_BOOT VIA MD0118PA00X+057047Y-042638X0236Y0000R000S3 +317IGGER/TRIG_ADC VIA MD0118PA00X+051209Y-036457X0236Y0000R000S3 +317ECT/BTN_THR_UP VIA MD0118PA00X+047982Y-042151X0236Y0000R000S3 +317ECT/BTN_THR_UP VIA MD0118PA00X+051299Y-045906X0236Y0000R000S3 +317ECT/BTN_MACRO6 VIA MD0118PA00X+055630Y-041969X0236Y0000R000S3 +317ECT/BTN_MACRO6 VIA MD0118PA00X+056142Y-040315X0236Y0000R000S3 +317ECT/BTN_MACRO1 VIA MD0118PA00X+050472Y-041516X0236Y0000R000S3 +317ECT/BTN_MACRO1 VIA MD0118PA00X+051339Y-043268X0236Y0000R000S3 +317OMETER/I2C_SDA VIA MD0118PA00X+048898Y-043937X0236Y0000R000S3 +317OMETER/I2C_SDA VIA MD0118PA00X+049055Y-043228X0236Y0000R000S3 +317OMETER/I2C_SDA VIA MD0118PA00X+047982Y-049087X0236Y0000R000S3 +317OMETER/I2C_SCL VIA MD0118PA00X+049528Y-043189X0236Y0000R000S3 +317OMETER/I2C_SCL VIA MD0118PA00X+048307Y-044921X0236Y0000R000S3 +317OMETER/I2C_SCL VIA MD0118PA00X+047677Y-049165X0236Y0000R000S3 +317/XBEE_SLEEP_RQ VIA MD0118PA00X+054685Y-041811X0236Y0000R000S3 +317ECT/BTN_MACRO5 VIA MD0118PA00X+052480Y-039685X0236Y0000R000S3 +317ECT/BTN_MACRO5 VIA MD0118PA00X+052402Y-042126X0236Y0000R000S3 +317ECT/BTN_MACRO5 VIA MD0118PA00X+053607Y-039818X0236Y0000R000S3 +317MCU_CORE/STAT2 VIA MD0118PA00X+051506Y-042550X0236Y0000R000S3 +317MCU_CORE/STAT1 VIA MD0118PA00X+051496Y-042874X0236Y0000R000S3 +317MCU_CORE/STAT1 VIA MD0118PA00X+050197Y-038976X0236Y0000R000S3 +317MCU_CORE/STAT1 VIA MD0118PA00X+049665Y-038374X0236Y0000R000S3 +317CORE/BTN_STICK VIA MD0118PA00X+051378Y-043622X0236Y0000R000S3 +317CORE/BTN_STICK VIA MD0118PA00X+049843Y-039528X0236Y0000R000S3 +317/PWR_BTN_SENSE VIA MD0118PA00X+047480Y-049514X0236Y0000R000S3 +317/PWR_BTN_SENSE VIA MD0118PA00X+051378Y-044961X0236Y0000R000S3 +317/PWR_BTN_SENSE VIA MD0118PA00X+048819Y-047087X0236Y0000R000S3 +317T/BTN_TRIG_DIG VIA MD0118PA00X+051575Y-024685X0236Y0000R000S3 +317T/BTN_TRIG_DIG VIA MD0118PA00X+048150Y-034567X0236Y0000R000S3 +317T/BTN_TRIG_DIG VIA MD0118PA00X+051850Y-045315X0236Y0000R000S3 +317T/BTN_TRIG_DIG VIA MD0118PA00X+049016Y-026693X0236Y0000R000S3 +317T/BTN_TRIG_DIG VIA MD0118PA00X+047990Y-041825X0236Y0000R000S3 +317/XBEE/XBEE_CTS VIA MD0118PA00X+050315Y-046378X0236Y0000R000S3 +317U_CORE/RGB_DIN VIA MD0118PA00X+049607Y-048559X0236Y0000R000S3 +317U_CORE/RGB_DIN VIA MD0118PA00X+051339Y-046220X0236Y0000R000S3 +317/XBEE/XBEE_DIN VIA MD0118PA00X+051252Y-047516X0236Y0000R000S3 +317XBEE/XBEE_DOUT VIA MD0118PA00X+051817Y-046667X0236Y0000R000S3 +317ACCEL_INT1 VIA MD0118PA00X+054882Y-046024X0236Y0000R000S3 +317ECT/BTN_VOL_UP VIA MD0118PA00X+057888Y-038644X0236Y0000R000S3 +317ECT/BTN_VOL_UP VIA MD0118PA00X+052362Y-046535X0236Y0000R000S3 +317/XBEE/XBEE_RTS VIA MD0118PA00X+052717Y-046535X0236Y0000R000S3 +317ECT/BTN_VOL_DN VIA MD0118PA00X+058150Y-038819X0236Y0000R000S3 +317ECT/BTN_VOL_DN VIA MD0118PA00X+053031Y-046339X0236Y0000R000S3 +317/XBEE_ON_SLEEP VIA MD0118PA00X+053386Y-046575X0236Y0000R000S3 +317BEE/XBEE_RESET VIA MD0118PA00X+053740Y-046575X0236Y0000R000S3 +317_CORE/PWR_HOLD VIA MD0118PA00X+055492Y-035709X0236Y0000R000S3 317_CORE/PWR_HOLD VIA MD0118PA00X+054522Y-028559X0236Y0000R000S3 -317_CORE/PWR_HOLD VIA MD0118PA00X+051033Y-038676X0236Y0000R000S3 -317ER/TRIG_ANALOG VIA MD0118PA00X+050103Y-026320X0236Y0000R000S3 -317ER/TRIG_ANALOG VIA MD0118PA00X+049879Y-031744X0236Y0000R000S3 -327VSYS C_SYS_-1 A01X+053051Y-047368X0394Y0571R000S2 -327GND C_SYS_-2 A01X+053799Y-047368X0394Y0571R000S2 +317_CORE/PWR_HOLD VIA MD0118PA00X+055906Y-042244X0236Y0000R000S3 +317VBUS VIA MD0118PA00X+048720Y-037500X0236Y0000R000S3 +317VBUS VIA MD0118PA00X+053937Y-049173X0236Y0000R000S3 +317VBUS VIA MD0118PA00X+048150Y-040472X0236Y0000R000S3 +317/USB_C/USB_CC1 VIA MD0118PA00X+050866Y-048701X0236Y0000R000S3 +317/USB_C/USB_CC2 VIA MD0118PA00X+056024Y-049173X0236Y0000R000S3 +317VSYS VIA MD0118PA00X+051063Y-036752X0236Y0000R000S3 +317VSYS VIA MD0118PA00X+055945Y-031220X0236Y0000R000S3 +317VSYS VIA MD0118PA00X+057008Y-035689X0236Y0000R000S3 +317VSYS VIA MD0118PA00X+056929Y-033976X0236Y0000R000S3 +317VBAT VIA MD0118PA00X+053504Y-038976X0236Y0000R000S3 +317VBAT VIA MD0118PA00X+057992Y-043031X0236Y0000R000S3 +317R_BUCK/BUCK_FB VIA MD0118PA00X+055073Y-038671X0236Y0000R000S3 +317R_BUCK/BUCK_FB VIA MD0118PA00X+054921Y-037343X0236Y0000R000S3 +3273V3 C_3V3_-1 A01X+055354Y-040957X0220Y0244R270S2 +327GND C_3V3_-2 A01X+055354Y-040579X0220Y0244R270S2 327ECT/BTN_MACRO4 SW_MAC-1 A01X+048750Y-039941X0413Y0256R000S2 327ECT/BTN_MACRO4 SW_MAC-1 A01X+050384Y-039941X0413Y0256R000S2 327GND SW_MAC-2 A01X+048750Y-040787X0413Y0256R000S2 327GND SW_MAC-2 A01X+050384Y-040787X0413Y0256R000S2 -327VBUS C_VIN_-1 A01X+049902Y-046959X0220Y0244R270S2 -327GND C_VIN_-2 A01X+049902Y-046581X0220Y0244R270S2 -327VBUS C_VIN_-1 A01X+049114Y-046974X0394Y0571R180S2 -327GND C_VIN_-2 A01X+048366Y-046974X0394Y0571R180S2 -3273V3 C_BUCK-1 A01X+051762Y-043602X0394Y0571R270S2 -327GND C_BUCK-2 A01X+051762Y-042854X0394Y0571R270S2 -3273V3 C_RGB1-1 A01X+050106Y-048720X0220Y0244R000S2 -327GND C_RGB1-2 A01X+050484Y-048720X0220Y0244R000S2 +3273V3 C_OLED-1 A01X+048888Y-041378X0354Y0374R180S2 +327GND C_OLED-2 A01X+048278Y-041378X0354Y0374R180S2 +327CU_CORE/MCU_EN R_EN_P-1 A01X+057280Y-046693X0213Y0252R000S2 +3273V3 R_EN_P-2 A01X+057681Y-046693X0213Y0252R000S2 +3273V3 C_RGB1-1 A01X+049528Y-049244X0220Y0244R270S2 +327GND C_RGB1-2 A01X+049528Y-048866X0220Y0244R270S2 +327GND SW_BOO-1 A01X+057510Y-045896X0413Y0256R270S2 +327GND SW_BOO-1 A01X+057510Y-044262X0413Y0256R270S2 +327_CORE/MCU_BOOT SW_BOO-2 A01X+058356Y-045896X0413Y0256R270S2 +327_CORE/MCU_BOOT SW_BOO-2 A01X+058356Y-044262X0413Y0256R270S2 +327IGGER/TRIG_ADC C_TRIG-1 A01X+051811Y-040878X0220Y0244R270S2 +327GND C_TRIG-2 A01X+051811Y-040500X0220Y0244R270S2 327N/C FID1 A01X+049606Y-024311X0394Y0000R000S2 327ECT/BTN_MACRO2 SW_MAC-1 A01X+052333Y-037106X0413Y0256R000S2 327ECT/BTN_MACRO2 SW_MAC-1 A01X+053967Y-037106X0413Y0256R000S2 327GND SW_MAC-2 A01X+052333Y-037953X0413Y0256R000S2 327GND SW_MAC-2 A01X+053967Y-037953X0413Y0256R000S2 -327VSYS C_BUCK-1 A01X+055472Y-045000X0394Y0571R180S2 -327GND C_BUCK-2 A01X+054724Y-045000X0394Y0571R180S2 -327VSYS C_SYS_-1 A01X+052067Y-047368X0220Y0244R270S2 -327GND C_SYS_-2 A01X+052067Y-046990X0220Y0244R270S2 +327CU_CORE/MCU_EN C_EN1 -1 A01X+057175Y-047362X0354Y0374R000S2 +327GND C_EN1 -2 A01X+057785Y-047362X0354Y0374R000S2 +327CU_CORE/USB_DM R_USB_-1 A01X+050402Y-045264X0213Y0252R270S2 +327ORE/USB_DM_MCU R_USB_-2 A01X+050402Y-044862X0213Y0252R270S2 367N/C SW_THR D0354UA00X+047953Y-028100X0354Y0000R090S0 367N/C SW_THR D0354UA00X+047953Y-029774X0354Y0000R090S0 327ECT/BTN_THR_UP SW_THR-1 A01X+048307Y-028455X0295Y0709R090S2 @@ -185,34 +164,90 @@ P arrayDim N 327_LED/RGB_DIN_R D_RGB1-2 A01X+050335Y-049350X0591Y0394R270S2 3273V3 D_RGB1-3 A01X+050335Y-050650X0591Y0394R270S2 327N/C D_RGB1-4 A01X+051043Y-050650X0591Y0394R270S2 -327VBAT C_BAT1-1 A01X+052461Y-045990X0394Y0571R000S2 -327GND C_BAT1-2 A01X+053209Y-045990X0394Y0571R000S2 367N/C MH1 D0866UA00X+048228Y-024646X0866Y0000R000S0 -327VSYS U_CHG1-1 A01X+051496Y-046896X0197Y0079R180S3 -327VBAT U_CHG1-2 A01X+051496Y-046738X0197Y0079R180S3 -327MCU_CORE/STAT2 U_CHG1-3 A01X+051496Y-046581X0197Y0079R180S3 -327GND U_CHG1-4 A01X+051496Y-046423X0197Y0079R180S3 -327GND U_CHG1-5 A01X+051496Y-046266X0197Y0079R180S3 -327CHARGER/CHG_TS U_CHG1-6 A01X+050669Y-046266X0197Y0079R180S3 -327ARGER/CHG_VSET U_CHG1-7 A01X+050669Y-046423X0197Y0079R180S3 -327ARGER/CHG_ISET U_CHG1-8 A01X+050669Y-046581X0197Y0079R180S3 -327MCU_CORE/STAT1 U_CHG1-9 A01X+050669Y-046738X0197Y0079R180S3 -327VBUS U_CHG1-10 A01X+050669Y-046896X0197Y0079R180S3 -327GND U_CHG1-11 A01X+051083Y-046581X0197Y0197R180S3 -317GND U_CHG1-12 D0079PA00X+051083Y-046778X0118Y0000R180S3 -317GND U_CHG1-13 D0079PA00X+051083Y-046384X0118Y0000R180S3 -327GND U_OLED-1 A01X+048386Y-041781X0236Y0610R000S2 -3273V3 U_OLED-2 A01X+048780Y-041781X0236Y0610R000S2 -327OMETER/I2C_SDA U_OLED-3 A01X+049173Y-041781X0236Y0610R000S2 -327OMETER/I2C_SCL U_OLED-4 A01X+049567Y-041781X0236Y0610R000S2 -327N/C U_OLED-MP A01X+047874Y-043307X0472Y0709R000S2 -327N/C U_OLED-MP A01X+050079Y-043307X0472Y0709R000S2 -327MCU_CORE/STAT2 R_STAT-1 A01X+052693Y-045085X0213Y0252R000S2 -3273V3 R_STAT-2 A01X+053094Y-045085X0213Y0252R000S2 +327GND U_OLED-1 A01X+048386Y-042569X0236Y0610R000S2 +3273V3 U_OLED-2 A01X+048780Y-042569X0236Y0610R000S2 +327OMETER/I2C_SDA U_OLED-3 A01X+049173Y-042569X0236Y0610R000S2 +327OMETER/I2C_SCL U_OLED-4 A01X+049567Y-042569X0236Y0610R000S2 +327N/C U_OLED-MP A01X+047874Y-044094X0472Y0709R000S2 +327N/C U_OLED-MP A01X+050079Y-044094X0472Y0709R000S2 367N/C MH4 D0866UA00X+057874Y-050000X0866Y0000R000S0 327N/C FID2 A01X+056594Y-024311X0394Y0000R000S2 -327R_BUCK/BUCK_FB R_FB2 -1 A01X+052453Y-042018X0213Y0252R000S2 -327GND R_FB2 -2 A01X+052854Y-042018X0213Y0252R000S2 +3273V3 C_OLED-1 A01X+048772Y-041850X0220Y0244R180S2 +327GND C_OLED-2 A01X+048394Y-041850X0220Y0244R180S2 +327GND U_MCU1-1 A01X+056083Y-041535X0157Y0315R000S2 +327GND U_MCU1-2 A01X+055748Y-041535X0157Y0315R000S2 +3273V3 U_MCU1-3 A01X+055413Y-041535X0157Y0315R000S2 +327_CORE/MCU_BOOT U_MCU1-4 A01X+055079Y-041535X0157Y0315R000S2 +327/XBEE_SLEEP_RQ U_MCU1-5 A01X+054744Y-041535X0157Y0315R000S2 +327ECT/BTN_MACRO6 U_MCU1-6 A01X+054409Y-041535X0157Y0315R000S2 +327N/C U_MCU1-7 A01X+054075Y-041535X0157Y0315R000S2 +327ECT/BTN_MACRO3 U_MCU1-8 A01X+053740Y-041535X0157Y0315R000S2 +327ECT/BTN_MACRO2 U_MCU1-9 A01X+053406Y-041535X0157Y0315R000S2 +327U_CORE/STICK_Y U_MCU1-10 A01X+053071Y-041535X0157Y0315R000S2 +327U_CORE/STICK_X U_MCU1-11 A01X+052736Y-041535X0157Y0315R000S2 +327ECT/BTN_MACRO5 U_MCU1-12 A01X+052402Y-041535X0157Y0315R000S2 +327IGGER/TRIG_ADC U_MCU1-13 A01X+052067Y-041535X0157Y0315R000S2 +327ORE/VSYS_SENSE U_MCU1-14 A01X+051732Y-041535X0157Y0315R000S2 +327ECT/BTN_MACRO4 U_MCU1-15 A01X+051398Y-041535X0157Y0315R000S2 +327OMETER/I2C_SDA U_MCU1-16 A01X+050984Y-041949X0157Y0315R090S2 +327OMETER/I2C_SCL U_MCU1-17 A01X+050984Y-042283X0157Y0315R090S2 +327MCU_CORE/STAT2 U_MCU1-18 A01X+050984Y-042618X0157Y0315R090S2 +327MCU_CORE/STAT1 U_MCU1-19 A01X+050984Y-042953X0157Y0315R090S2 +327ECT/BTN_MACRO1 U_MCU1-20 A01X+050984Y-043287X0157Y0315R090S2 +327CORE/BTN_STICK U_MCU1-21 A01X+050984Y-043622X0157Y0315R090S2 +327ECT/BTN_THR_DN U_MCU1-22 A01X+050984Y-043957X0157Y0315R090S2 +327ORE/USB_DM_MCU U_MCU1-23 A01X+050984Y-044291X0157Y0315R090S2 +327ORE/USB_DP_MCU U_MCU1-24 A01X+050984Y-044626X0157Y0315R090S2 +327/PWR_BTN_SENSE U_MCU1-25 A01X+050984Y-044961X0157Y0315R090S2 +327N/C U_MCU1-26 A01X+050984Y-045295X0157Y0315R090S2 +327T/BTN_TRIG_DIG U_MCU1-27 A01X+050984Y-045630X0157Y0315R090S2 +327ECT/BTN_THR_UP U_MCU1-28 A01X+050984Y-045965X0157Y0315R090S2 +327/XBEE/XBEE_CTS U_MCU1-29 A01X+050984Y-046299X0157Y0315R090S2 +327U_CORE/RGB_DIN U_MCU1-30 A01X+050984Y-046634X0157Y0315R090S2 +327/XBEE/XBEE_DIN U_MCU1-31 A01X+051398Y-047047X0157Y0315R000S2 +327XBEE/XBEE_DOUT U_MCU1-32 A01X+051732Y-047047X0157Y0315R000S2 +327ACCEL_INT1 U_MCU1-33 A01X+052067Y-047047X0157Y0315R000S2 +327ECT/BTN_VOL_UP U_MCU1-34 A01X+052402Y-047047X0157Y0315R000S2 +327/XBEE/XBEE_RTS U_MCU1-35 A01X+052736Y-047047X0157Y0315R000S2 +327ECT/BTN_VOL_DN U_MCU1-36 A01X+053071Y-047047X0157Y0315R000S2 +327/XBEE_ON_SLEEP U_MCU1-37 A01X+053406Y-047047X0157Y0315R000S2 +327BEE/XBEE_RESET U_MCU1-38 A01X+053740Y-047047X0157Y0315R000S2 +327N/C U_MCU1-39 A01X+054075Y-047047X0157Y0315R000S2 +327_CORE/PWR_HOLD U_MCU1-40 A01X+054409Y-047047X0157Y0315R000S2 +327N/C U_MCU1-41 A01X+054744Y-047047X0157Y0315R000S2 +327GND U_MCU1-42 A01X+055079Y-047047X0157Y0315R000S2 +327GND U_MCU1-43 A01X+055413Y-047047X0157Y0315R000S2 +327N/C U_MCU1-44 A01X+055748Y-047047X0157Y0315R000S2 +327CU_CORE/MCU_EN U_MCU1-45 A01X+056083Y-047047X0157Y0315R000S2 +327GND U_MCU1-46 A01X+056496Y-046634X0157Y0315R090S2 +327GND U_MCU1-47 A01X+056496Y-046299X0157Y0315R090S2 +327GND U_MCU1-48 A01X+056496Y-045965X0157Y0315R090S2 +327GND U_MCU1-49 A01X+056496Y-045630X0157Y0315R090S2 +327GND U_MCU1-50 A01X+056496Y-045295X0157Y0315R090S2 +327GND U_MCU1-51 A01X+056496Y-044961X0157Y0315R090S2 +327GND U_MCU1-52 A01X+056496Y-044626X0157Y0315R090S2 +327GND U_MCU1-53 A01X+056496Y-044291X0157Y0315R090S2 +327GND U_MCU1-54 A01X+056496Y-043957X0157Y0315R090S2 +327GND U_MCU1-55 A01X+056496Y-043622X0157Y0315R090S2 +327GND U_MCU1-56 A01X+056496Y-043287X0157Y0315R090S2 +327GND U_MCU1-57 A01X+056496Y-042953X0157Y0315R090S2 +327GND U_MCU1-58 A01X+056496Y-042618X0157Y0315R090S2 +327GND U_MCU1-59 A01X+056496Y-042283X0157Y0315R090S2 +327GND U_MCU1-60 A01X+056496Y-041949X0157Y0315R090S2 +327GND U_MCU1-61 A01X+054390Y-043642X0236Y0236R090S2 +327GND U_MCU1-61 A01X+053740Y-043642X0472Y0472R090S2 +327GND U_MCU1-61 A01X+053091Y-043642X0472Y0472R090S2 +327GND U_MCU1-61 A01X+054390Y-044291X0472Y0472R090S2 +327GND U_MCU1-61 A01X+053740Y-044291X0472Y0472R090S2 +327GND U_MCU1-61 A01X+053091Y-044291X0472Y0472R090S2 +327GND U_MCU1-61 A01X+054390Y-044941X0472Y0472R090S2 +327GND U_MCU1-61 A01X+053740Y-044941X0472Y0472R090S2 +327GND U_MCU1-61 A01X+053091Y-044941X0472Y0472R090S2 +327GND U_MCU1-62 A01X+056496Y-041535X0315Y0315R270S2 +327GND U_MCU1-63 A01X+050984Y-041535X0315Y0315R270S2 +327GND U_MCU1-64 A01X+050984Y-047047X0315Y0315R270S2 +327GND U_MCU1-65 A01X+056496Y-047047X0315Y0315R270S2 367N/C SW_VOL D0354UA00X+058346Y-033711X0354Y0000R270S0 367N/C SW_VOL D0354UA00X+058346Y-032037X0354Y0000R270S0 327ECT/BTN_VOL_DN SW_VOL-1 A01X+057992Y-033356X0295Y0709R270S2 @@ -242,8 +277,6 @@ P arrayDim N 317GND J_USB1-SH D0236PA00X+052236Y-050472X0394Y0630R000S0 317GND J_USB1-SH D0236PA00X+055638Y-048827X0394Y0827R000S0 317GND J_USB1-SH D0236PA00X+055638Y-050472X0394Y0630R000S0 -327ARGER/CHG_VSET R_VSET-1 A01X+048335Y-045472X0213Y0252R180S2 -327GND R_VSET-2 A01X+047933Y-045472X0213Y0252R180S2 317N/C J_STIC D0610PA00X+050659Y-028937X1004Y0000R000S0 317N/C J_STIC D0610PA00X+050659Y-032874X1004Y0000R000S0 317N/C J_STIC D0610PA00X+055640Y-028937X1004Y0000R000S0 @@ -252,23 +285,25 @@ P arrayDim N 317GND J_STIC-1' D0413PA00X+056587Y-031890X0807Y0000R000S0 317U_CORE/STICK_X J_STIC-2 D0413PA00X+053150Y-027469X0807Y0000R000S0 317U_CORE/STICK_Y J_STIC-2' D0413PA00X+056587Y-030906X0807Y0000R000S0 -317CU_CORE/3V3_RF J_STIC-3 D0413PA00X+052165Y-027469X0807Y0000R000S0 -317CU_CORE/3V3_RF J_STIC-3' D0413PA00X+056587Y-029921X0807Y0000R000S0 +3173V3 J_STIC-3 D0413PA00X+052165Y-027469X0807Y0000R000S0 +3173V3 J_STIC-3' D0413PA00X+056587Y-029921X0807Y0000R000S0 317CORE/BTN_STICK J_STIC-a D0492PA00X+051870Y-033169X0886Y0000R000S0 317N/C J_STIC-b D0492PA00X+054429Y-033169X0886Y0000R000S0 317GND J_STIC-c D0492PA00X+051870Y-034941X0886Y0000R000S0 317N/C J_STIC-d D0492PA00X+054429Y-034941X0886Y0000R000S0 -327MCU_CORE/STAT1 R_STAT-1 A01X+049476Y-046187X0213Y0252R180S2 -3273V3 R_STAT-2 A01X+049075Y-046187X0213Y0252R180S2 -327ARGER/CHG_ISET R_ISET-1 A01X+048343Y-045872X0213Y0252R180S2 -327GND R_ISET-2 A01X+047941Y-045872X0213Y0252R180S2 327/PWR_BTN_SENSE C_DBNC-1 A01X+048850Y-049291X0220Y0244R180S2 327GND C_DBNC-2 A01X+048472Y-049291X0220Y0244R180S2 -327_LED/RGB_DIN_R R_RGB1-1 A01X+050094Y-048268X0213Y0252R000S2 -327U_CORE/RGB_DIN R_RGB1-2 A01X+050496Y-048268X0213Y0252R000S2 -327R_BUCK/BUCK_FB R_FB1 -1 A01X+051959Y-041748X0213Y0252R090S2 -3273V3 R_FB1 -2 A01X+051959Y-042150X0213Y0252R090S2 +327_LED/RGB_DIN_R R_RGB1-1 A01X+050354Y-048622X0213Y0252R270S2 +327U_CORE/RGB_DIN R_RGB1-2 A01X+050354Y-048220X0213Y0252R270S2 367N/C MH2 D0866UA00X+058031Y-024724X0866Y0000R000S0 +3273V3 C_3V3_-1 A01X+055354Y-040189X0220Y0244R270S2 +327GND C_3V3_-2 A01X+055354Y-039811X0220Y0244R270S2 +3273V3 C_3V3_-1 A01X+057205Y-042037X0354Y0374R270S2 +327GND C_3V3_-2 A01X+057205Y-041427X0354Y0374R270S2 +327VSYS R_VSYS-1 A01X+051102Y-039724X0213Y0252R090S2 +327ORE/VSYS_SENSE R_VSYS-2 A01X+051102Y-040126X0213Y0252R090S2 +3273V3 R_I2C_-1 A01X+049409Y-041449X0213Y0252R090S2 +327OMETER/I2C_SDA R_I2C_-2 A01X+049409Y-041850X0213Y0252R090S2 367N/C SW_THR D0354UA00X+047953Y-032037X0354Y0000R090S0 367N/C SW_THR D0354UA00X+047953Y-033711X0354Y0000R090S0 327ECT/BTN_THR_DN SW_THR-1 A01X+048307Y-032392X0295Y0709R090S2 @@ -276,6 +311,8 @@ P arrayDim N 327GND SW_THR-2 A01X+048307Y-032874X0236Y0709R090S2 327N/C SW_THR-MP A01X+047539Y-032146X0512Y0354R090S2 327N/C SW_THR-MP A01X+047539Y-033602X0512Y0354R090S2 +3273V3 R_I2C_-1 A01X+050079Y-041886X0213Y0252R090S2 +327OMETER/I2C_SCL R_I2C_-2 A01X+050079Y-042287X0213Y0252R090S2 367N/C SW_VOL D0354UA00X+058346Y-029774X0354Y0000R270S0 367N/C SW_VOL D0354UA00X+058346Y-028100X0354Y0000R270S0 327ECT/BTN_VOL_UP SW_VOL-1 A01X+057992Y-029419X0295Y0709R270S2 @@ -283,14 +320,9 @@ P arrayDim N 327GND SW_VOL-2 A01X+057992Y-028937X0236Y0709R270S2 327N/C SW_VOL-MP A01X+058760Y-029665X0512Y0354R270S2 327N/C SW_VOL-MP A01X+058760Y-028209X0512Y0354R270S2 -327ER_BUCK/PWR_EN U_BUCK-1 A01X+055856Y-043228X0522Y0236R090S2 -327GND U_BUCK-2 A01X+055482Y-043228X0522Y0236R090S2 -327R_BUCK/BUCK_SW U_BUCK-3 A01X+055108Y-043228X0522Y0236R090S2 -327VSYS U_BUCK-4 A01X+055108Y-044124X0522Y0236R090S2 -327R_BUCK/BUCK_FB U_BUCK-5 A01X+055856Y-044124X0522Y0236R090S2 -327R_BUCK/BUCK_SW L_BUCK-1 A01X+054134Y-043228X0591Y1417R180S2 -3273V3 L_BUCK-2 A01X+052933Y-043228X0591Y1417R180S2 327N/C FID3 A01X+058465Y-047638X0394Y0000R000S2 +327ORE/VSYS_SENSE R_VSYS-1 A01X+051181Y-040508X0213Y0252R090S2 +327GND R_VSYS-2 A01X+051181Y-040909X0213Y0252R090S2 367N/C SW_PWR D0354UA00X+047589Y-050354X0354Y0000R000S0 367N/C SW_PWR D0354UA00X+049262Y-050354X0354Y0000R000S0 327/PWR_BTN_SENSE SW_PWR-1 A01X+047943Y-050000X0295Y0709R000S2 @@ -299,27 +331,33 @@ P arrayDim N 327N/C SW_PWR-MP A01X+047697Y-050768X0512Y0354R000S2 327N/C SW_PWR-MP A01X+049154Y-050768X0512Y0354R000S2 367N/C MH3 D0866UA00X+048425Y-048228X0866Y0000R000S0 +327CU_CORE/USB_DP R_USB_-1 A01X+050402Y-046028X0213Y0252R270S2 +327ORE/USB_DP_MCU R_USB_-2 A01X+050402Y-045626X0213Y0252R270S2 327ECT/BTN_MACRO5 SW_MAC-1 A01X+052333Y-039941X0413Y0256R000S2 327ECT/BTN_MACRO5 SW_MAC-1 A01X+053967Y-039941X0413Y0256R000S2 327GND SW_MAC-2 A01X+052333Y-040787X0413Y0256R000S2 327GND SW_MAC-2 A01X+053967Y-040787X0413Y0256R000S2 -327CHARGER/CHG_TS R_TS1 -1 A01X+048335Y-045079X0213Y0252R180S2 -327GND R_TS1 -2 A01X+047933Y-045079X0213Y0252R180S2 -3273V3 R_BTN_-1 A04X+049173Y-037244X0213Y0252R000S1 -327/PWR_BTN_SENSE R_BTN_-2 A04X+049575Y-037244X0213Y0252R000S1 +327_CORE/MCU_BOOT R_BOOT-1 A01X+057402Y-043276X0213Y0252R270S2 +3273V3 R_BOOT-2 A01X+057402Y-042874X0213Y0252R270S2 +3273V3 R_BTN_-1 A04X+050150Y-036915X0213Y0252R180S1 +327/PWR_BTN_SENSE R_BTN_-2 A04X+049749Y-036915X0213Y0252R180S1 +327VSYS C_SYS_-1 A04X+052657Y-037106X0394Y0571R000S1 +327GND C_SYS_-2 A04X+053406Y-037106X0394Y0571R000S1 327NTROL/PWR_GATE Q_PWR1-1 A04X+054069Y-030341X0581Y0236R090S1 327VSYS Q_PWR1-2 A04X+054817Y-030341X0581Y0236R090S1 327ER_BUCK/PWR_EN Q_PWR1-3 A04X+054443Y-031079X0581Y0236R090S1 -327VBUS C_VBUS-1 A04X+055315Y-035246X0354Y0374R270S1 -327GND C_VBUS-2 A04X+055315Y-034636X0354Y0374R270S1 327VBUS D_VBUS-1 A04X+053482Y-049703X0236Y0177R000S1 327GND D_VBUS-2 A04X+054309Y-049703X0236Y0177R000S1 317VBAT BT1 -1 D0295PA00X+057165Y-048465X0472Y0689R000S0 317GND BT1 -2 D0295PA00X+057953Y-048465X0472Y0689R000S0 327N/C FID4 A04X+057087Y-024311X0394Y0000R000S1 -3273V3 C_OLED-1 A04X+048652Y-042441X0354Y0374R180S1 -327GND C_OLED-2 A04X+048041Y-042441X0354Y0374R180S1 +327VBUS C_VIN_-1 A04X+049508Y-037516X0220Y0244R090S1 +327GND C_VIN_-2 A04X+049508Y-037894X0220Y0244R090S1 +327VBUS C_VIN_-1 A04X+048720Y-037500X0394Y0571R180S1 +327GND C_VIN_-2 A04X+047972Y-037500X0394Y0571R180S1 327N/C FID6 A04X+056890Y-050492X0394Y0000R000S1 +3273V3 C_BUCK-1 A04X+054341Y-037323X0394Y0571R090S1 +327GND C_BUCK-2 A04X+054341Y-038071X0394Y0571R090S1 327R_BTN_INV_BASE D_INV_-1 A04X+049079Y-035724X0364Y0177R090S1 327N/C D_INV_-2 A04X+049591Y-035724X0364Y0177R090S1 327/PWR_BTN_SENSE D_INV_-3 A04X+049335Y-036423X0364Y0177R090S1 @@ -328,32 +366,26 @@ P arrayDim N 327ER_BUCK/PWR_EN R_PWR_-1 A04X+055285Y-031591X0213Y0252R000S1 327GND R_PWR_-2 A04X+055687Y-031591X0213Y0252R000S1 327N/C FID5 A04X+048327Y-050492X0394Y0000R000S1 -327GND SW_BOO-1 A04X+056732Y-042106X0413Y0256R000S1 -327GND SW_BOO-1 A04X+058366Y-042106X0413Y0256R000S1 -327_CORE/MCU_BOOT SW_BOO-2 A04X+056732Y-041260X0413Y0256R000S1 -327_CORE/MCU_BOOT SW_BOO-2 A04X+058366Y-041260X0413Y0256R000S1 -327IGGER/TRIG_ADC C_TRIG-1 A04X+051961Y-036122X0220Y0244R180S1 -327GND C_TRIG-2 A04X+051583Y-036122X0220Y0244R180S1 -3273V3 FB_RF1-1 A04X+054739Y-035974X0344Y0374R000S1 -327CU_CORE/3V3_RF FB_RF1-2 A04X+055359Y-035974X0344Y0374R000S1 -327GND U_IMU1-1 A04X+057426Y-026398X0246Y0138R180S1 -327GND U_IMU1-2 A04X+057426Y-026594X0246Y0138R180S1 -327GND U_IMU1-3 A04X+057426Y-026791X0246Y0138R180S1 -327ACCEL_INT1 U_IMU1-4 A04X+057426Y-026988X0246Y0138R180S1 -3273V3 U_IMU1-5 A04X+057165Y-027052X0138Y0246R180S1 -327GND U_IMU1-6 A04X+056969Y-027052X0138Y0246R180S1 -327GND U_IMU1-7 A04X+056772Y-027052X0138Y0246R180S1 -3273V3 U_IMU1-8 A04X+056511Y-026988X0246Y0138R180S1 -327N/C U_IMU1-9 A04X+056511Y-026791X0246Y0138R180S1 -327GND U_IMU1-10 A04X+056511Y-026594X0246Y0138R180S1 -327GND U_IMU1-11 A04X+056511Y-026398X0246Y0138R180S1 -3273V3 U_IMU1-12 A04X+056772Y-026334X0138Y0246R180S1 -327OMETER/I2C_SCL U_IMU1-13 A04X+056969Y-026334X0138Y0246R180S1 -327OMETER/I2C_SDA U_IMU1-14 A04X+057165Y-026334X0138Y0246R180S1 +327GND U_IMU1-1 A04X+050812Y-049646X0246Y0138R090S1 +327GND U_IMU1-2 A04X+051009Y-049646X0246Y0138R090S1 +327GND U_IMU1-3 A04X+051206Y-049646X0246Y0138R090S1 +327ACCEL_INT1 U_IMU1-4 A04X+051403Y-049646X0246Y0138R090S1 +3273V3 U_IMU1-5 A04X+051467Y-049906X0138Y0246R090S1 +327GND U_IMU1-6 A04X+051467Y-050103X0138Y0246R090S1 +327GND U_IMU1-7 A04X+051467Y-050300X0138Y0246R090S1 +3273V3 U_IMU1-8 A04X+051403Y-050561X0246Y0138R090S1 +327N/C U_IMU1-9 A04X+051206Y-050561X0246Y0138R090S1 +327GND U_IMU1-10 A04X+051009Y-050561X0246Y0138R090S1 +327GND U_IMU1-11 A04X+050812Y-050561X0246Y0138R090S1 +3273V3 U_IMU1-12 A04X+050748Y-050300X0138Y0246R090S1 +327OMETER/I2C_SCL U_IMU1-13 A04X+050748Y-050103X0138Y0246R090S1 +327OMETER/I2C_SDA U_IMU1-14 A04X+050748Y-049906X0138Y0246R090S1 +327VSYS C_BUCK-1 A04X+057677Y-036043X0394Y0571R270S1 +327GND C_BUCK-2 A04X+057677Y-035295X0394Y0571R270S1 327GND C_LATC-1 A04X+053341Y-029484X0220Y0244R180S1 327OL/PWR_LATCH_G C_LATC-2 A04X+052963Y-029484X0220Y0244R180S1 -327CU_CORE/3V3_RF C_HALL-1 A04X+050520Y-025433X0220Y0244R000S1 -327GND C_HALL-2 A04X+050898Y-025433X0220Y0244R000S1 +3273V3 C_HALL-1 A04X+050764Y-025118X0220Y0244R000S1 +327GND C_HALL-2 A04X+051142Y-025118X0220Y0244R000S1 327VSYS R_INV_-1 A04X+049560Y-035026X0213Y0252R180S1 327R_BTN_INV_BASE R_INV_-2 A04X+049158Y-035026X0213Y0252R180S1 367N/C SW_TRI D0354UA00X+052313Y-024331X0354Y0000R000S0 @@ -370,124 +402,78 @@ P arrayDim N 327OL/PWR_LATCH_G Q_LATC-1 A04X+052514Y-030291X0581Y0236R090S1 327GND Q_LATC-2 A04X+053262Y-030291X0581Y0236R090S1 327NTROL/PWR_GATE Q_LATC-3 A04X+052888Y-031030X0581Y0236R090S1 -367N/C J_SWD1 D0390UA00X+057598Y-045187X0390Y0000R270S0 -367N/C J_SWD1 D0390UA00X+057198Y-043187X0390Y0000R270S0 -367N/C J_SWD1 D0390UA00X+057998Y-043187X0390Y0000R270S0 -3273V3 J_SWD1-1 A04X+057348Y-044687X0310Y0000R270S1 -327MCU_CORE/SWDIO J_SWD1-2 A04X+057848Y-044687X0310Y0000R270S1 -327CORE/MCU_RESET J_SWD1-3 A04X+057348Y-044187X0310Y0000R270S1 -327CU_CORE/SWDCLK J_SWD1-4 A04X+057848Y-044187X0310Y0000R270S1 -327GND J_SWD1-5 A04X+057348Y-043687X0310Y0000R270S1 -327N/C J_SWD1-6 A04X+057848Y-043687X0310Y0000R270S1 -3273V3 C_IMU_-1 A04X+055413Y-026959X0354Y0374R090S1 -327GND C_IMU_-2 A04X+055413Y-027569X0354Y0374R090S1 +327VSYS C_SYS_-1 A04X+051673Y-037106X0220Y0244R090S1 +327GND C_SYS_-2 A04X+051673Y-037484X0220Y0244R090S1 +3273V3 C_IMU_-1 A04X+049400Y-049488X0354Y0374R180S1 +327GND C_IMU_-2 A04X+048789Y-049488X0354Y0374R180S1 +327VBAT C_BAT1-1 A04X+052067Y-038484X0394Y0571R000S1 +327GND C_BAT1-2 A04X+052815Y-038484X0394Y0571R000S1 +327VSYS U_CHG1-1 A04X+051102Y-037579X0197Y0079R180S3 +327VBAT U_CHG1-2 A04X+051102Y-037736X0197Y0079R180S3 +327MCU_CORE/STAT2 U_CHG1-3 A04X+051102Y-037894X0197Y0079R180S3 +327GND U_CHG1-4 A04X+051102Y-038051X0197Y0079R180S3 +327GND U_CHG1-5 A04X+051102Y-038209X0197Y0079R180S3 +327CHARGER/CHG_TS U_CHG1-6 A04X+050276Y-038209X0197Y0079R180S3 +327ARGER/CHG_VSET U_CHG1-7 A04X+050276Y-038051X0197Y0079R180S3 +327ARGER/CHG_ISET U_CHG1-8 A04X+050276Y-037894X0197Y0079R180S3 +327MCU_CORE/STAT1 U_CHG1-9 A04X+050276Y-037736X0197Y0079R180S3 +327VBUS U_CHG1-10 A04X+050276Y-037579X0197Y0079R180S3 +327GND U_CHG1-11 A04X+050689Y-037894X0197Y0197R180S3 +317GND U_CHG1-12 D0079PA00X+050689Y-037697X0118Y0000R180S3 +317GND U_CHG1-13 D0079PA00X+050689Y-038091X0118Y0000R180S3 +327MCU_CORE/STAT2 R_STAT-1 A04X+052299Y-039390X0213Y0252R000S1 +3273V3 R_STAT-2 A04X+052701Y-039390X0213Y0252R000S1 327/USB_C/USB_CC2 R_CC2 -1 A04X+055616Y-049632X0213Y0252R000S1 327GND R_CC2 -2 A04X+056018Y-049632X0213Y0252R000S1 -3273V3 C_OLED-1 A04X+048803Y-041417X0220Y0244R180S1 -327GND C_OLED-2 A04X+048425Y-041417X0220Y0244R180S1 327OL/PWR_LATCH_G D_OR2 -1 A04X+052612Y-028520X0354Y0472R000S1 327_CORE/PWR_HOLD D_OR2 -2 A04X+053911Y-028520X0354Y0472R000S1 327GND R_LATC-1 A04X+051880Y-029307X0213Y0252R000S1 327OL/PWR_LATCH_G R_LATC-2 A04X+052281Y-029307X0213Y0252R000S1 -327OMETER/I2C_SDA U_MCU1-1 A04X+050354Y-039961X0492Y0276R000S1 -327OMETER/I2C_SCL U_MCU1-2 A04X+050354Y-039528X0492Y0276R000S1 -327N/C U_MCU1-3 A04X+050354Y-039094X0492Y0276R000S1 -327N/C U_MCU1-4 A04X+050354Y-038661X0492Y0276R000S1 -327U_CORE/STICK_X U_MCU1-5 A04X+050354Y-038228X0492Y0276R000S1 -327U_CORE/STICK_Y U_MCU1-6 A04X+050354Y-037795X0492Y0276R000S1 -327N/C U_MCU1-7 A04X+050354Y-037362X0492Y0276R000S1 -327N/C U_MCU1-8 A04X+050354Y-036929X0492Y0276R000S1 -327CU_CORE/3V3_RF U_MCU1-9 A04X+055768Y-036929X0492Y0276R000S1 -327GND U_MCU1-10 A04X+055768Y-037362X0492Y0276R000S1 -327/PWR_BTN_SENSE U_MCU1-11 A04X+055768Y-037795X0492Y0276R000S1 -327_CORE/MCU_BOOT U_MCU1-12 A04X+055768Y-038228X0492Y0276R000S1 -327U_CORE/RGB_DIN U_MCU1-13 A04X+055768Y-038661X0492Y0276R000S1 -327CORE/MCU_RESET U_MCU1-14 A04X+055768Y-039094X0492Y0276R000S1 -327CU_CORE/SWDCLK U_MCU1-15 A04X+055768Y-039528X0492Y0276R000S1 -327MCU_CORE/SWDIO U_MCU1-16 A04X+055768Y-039961X0492Y0276R000S1 -327GND U_MCU1-A0 A04X+052175Y-039646X0236Y0000R000S1 -327N/C U_MCU1-A1 A04X+052175Y-039173X0236Y0000R000S1 -327N/C U_MCU1-A2 A04X+052175Y-038701X0236Y0000R000S1 -327IGGER/TRIG_ADC U_MCU1-A3 A04X+052175Y-038228X0236Y0000R000S1 -327ORE/VSYS_SENSE U_MCU1-A4 A04X+052175Y-037756X0236Y0000R000S1 -327ECT/BTN_MACRO2 U_MCU1-A5 A04X+052175Y-037283X0236Y0000R000S1 -327ECT/BTN_THR_UP U_MCU1-A6 A04X+052175Y-036811X0236Y0000R000S1 -327GND U_MCU1-B0 A04X+052766Y-039646X0236Y0000R000S1 -327N/C U_MCU1-B1 A04X+052766Y-039173X0236Y0000R000S1 -327N/C U_MCU1-B2 A04X+052766Y-038701X0236Y0000R000S1 -327N/C U_MCU1-B3 A04X+052766Y-038228X0236Y0000R000S1 -327N/C U_MCU1-B4 A04X+052766Y-037756X0236Y0000R000S1 -327N/C U_MCU1-B5 A04X+052766Y-037283X0236Y0000R000S1 -327CORE/BTN_STICK U_MCU1-B6 A04X+052766Y-036811X0236Y0000R000S1 -327GND U_MCU1-C0 A04X+053356Y-039646X0236Y0000R000S1 -327N/C U_MCU1-C1 A04X+053356Y-039173X0236Y0000R000S1 -327N/C U_MCU1-C2 A04X+053356Y-038701X0236Y0000R000S1 -327N/C U_MCU1-C3 A04X+053356Y-038228X0236Y0000R000S1 -327N/C U_MCU1-C4 A04X+053356Y-037756X0236Y0000R000S1 -327N/C U_MCU1-C5 A04X+053356Y-037283X0236Y0000R000S1 -327T/BTN_TRIG_DIG U_MCU1-C6 A04X+053356Y-036811X0236Y0000R000S1 -327GND U_MCU1-D0 A04X+053947Y-039646X0236Y0000R000S1 -327N/C U_MCU1-D1 A04X+053947Y-039173X0236Y0000R000S1 -327N/C U_MCU1-D2 A04X+053947Y-038701X0236Y0000R000S1 -327N/C U_MCU1-D3 A04X+053947Y-038228X0236Y0000R000S1 -327N/C U_MCU1-D4 A04X+053947Y-037756X0236Y0000R000S1 -327N/C U_MCU1-D5 A04X+053947Y-037283X0236Y0000R000S1 -327ECT/BTN_VOL_UP U_MCU1-D6 A04X+053947Y-036811X0236Y0000R000S1 -327ECT/BTN_MACRO5 U_MCU1-E0 A04X+054537Y-039646X0236Y0000R000S1 -327ECT/BTN_MACRO6 U_MCU1-E1 A04X+054537Y-039173X0236Y0000R000S1 -327N/C U_MCU1-E2 A04X+054537Y-038701X0236Y0000R000S1 -327ECT/BTN_MACRO3 U_MCU1-E3 A04X+054537Y-038228X0236Y0000R000S1 -327CU_CORE/USB_DP U_MCU1-E4 A04X+054537Y-037756X0236Y0000R000S1 -327CU_CORE/USB_DM U_MCU1-E5 A04X+054537Y-037283X0236Y0000R000S1 -327ECT/BTN_VOL_DN U_MCU1-E6 A04X+054537Y-036811X0236Y0000R000S1 -327GND U_MCU1-F0 A04X+051732Y-040433X0591Y0591R000S1 -327GND U_MCU1-F1 A04X+052618Y-040433X0591Y0591R000S1 -327GND U_MCU1-F2 A04X+053504Y-040433X0591Y0591R000S1 -327GND U_MCU1-F3 A04X+054390Y-040433X0591Y0591R000S1 -327CU_CORE/3V3_RF U_MCU1-F4 A04X+055128Y-037756X0236Y0000R000S1 -327N/C U_MCU1-F5 A04X+055128Y-037283X0236Y0000R000S1 -327VBUS U_MCU1-F6 A04X+055128Y-036811X0236Y0236R000S1 -327ECT/BTN_MACRO4 U_MCU1-Z0 A04X+051585Y-039646X0236Y0000R000S1 -327ACCEL_INT1 U_MCU1-Z1 A04X+051585Y-039173X0236Y0000R000S1 -327_CORE/PWR_HOLD U_MCU1-Z2 A04X+051585Y-038701X0236Y0000R000S1 -327MCU_CORE/STAT1 U_MCU1-Z3 A04X+051585Y-038228X0236Y0000R000S1 -327MCU_CORE/STAT2 U_MCU1-Z4 A04X+051585Y-037756X0236Y0000R000S1 -327ECT/BTN_MACRO1 U_MCU1-Z5 A04X+051585Y-037283X0236Y0000R000S1 -327ECT/BTN_THR_DN U_MCU1-Z6 A04X+051585Y-036811X0236Y0000R000S1 -3273V3 C_IMU_-1 A04X+057177Y-027559X0220Y0244R180S1 -327GND C_IMU_-2 A04X+056799Y-027559X0220Y0244R180S1 +327R_BUCK/BUCK_FB R_FB2 -1 A04X+054537Y-039563X0213Y0252R090S1 +327GND R_FB2 -2 A04X+054537Y-039965X0213Y0252R090S1 +327ARGER/CHG_VSET R_VSET-1 A04X+048142Y-039272X0213Y0252R180S1 +327GND R_VSET-2 A04X+047740Y-039272X0213Y0252R180S1 +3273V3 C_IMU_-1 A04X+050260Y-050591X0220Y0244R180S1 +327GND C_IMU_-2 A04X+049882Y-050591X0220Y0244R180S1 +327MCU_CORE/STAT1 R_STAT-1 A04X+049083Y-038287X0213Y0252R180S1 +3273V3 R_STAT-2 A04X+048681Y-038287X0213Y0252R180S1 +327ARGER/CHG_ISET R_ISET-1 A04X+048150Y-038681X0213Y0252R180S1 +327GND R_ISET-2 A04X+047748Y-038681X0213Y0252R180S1 327/USB_C/USB_CC1 R_CC1 -1 A04X+051285Y-048746X0213Y0252R000S1 327GND R_CC1 -2 A04X+051687Y-048746X0213Y0252R000S1 -327CU_CORE/3V3_RF C_3V3_-1 A04X+056911Y-037789X0220Y0244R270S1 -327GND C_3V3_-2 A04X+056911Y-037411X0220Y0244R270S1 -327CU_CORE/3V3_RF C_3V3_-1 A04X+056024Y-035974X0354Y0374R000S1 -327GND C_3V3_-2 A04X+056634Y-035974X0354Y0374R000S1 -327VSYS R_VSYS-1 A04X+052467Y-036069X0213Y0252R000S1 -327ORE/VSYS_SENSE R_VSYS-2 A04X+052868Y-036069X0213Y0252R000S1 -327CU_CORE/3V3_RF C_RF_B-1 A04X+057675Y-038138X0453Y0709R270S1 -327GND C_RF_B-2 A04X+057675Y-036976X0453Y0709R270S1 -3273V3 R_I2C_-1 A04X+049557Y-040555X0213Y0252R270S1 -327OMETER/I2C_SDA R_I2C_-2 A04X+049557Y-040154X0213Y0252R270S1 -3273V3 R_I2C_-1 A04X+049557Y-039669X0213Y0252R270S1 -327OMETER/I2C_SCL R_I2C_-2 A04X+049557Y-039268X0213Y0252R270S1 -327GND SW_RST-1 A04X+056732Y-040492X0413Y0256R000S1 -327GND SW_RST-1 A04X+058366Y-040492X0413Y0256R000S1 -327CORE/MCU_RESET SW_RST-2 A04X+056732Y-039646X0413Y0256R000S1 -327CORE/MCU_RESET SW_RST-2 A04X+058366Y-039646X0413Y0256R000S1 -3273V3 C_IMU_-1 A04X+056004Y-026976X0220Y0244R090S1 -327GND C_IMU_-2 A04X+056004Y-027354X0220Y0244R090S1 -327ORE/VSYS_SENSE R_VSYS-1 A04X+053352Y-036069X0213Y0252R000S1 -327GND R_VSYS-2 A04X+053754Y-036069X0213Y0252R000S1 -327CU_CORE/3V3_RF C_STIC-1 A04X+057285Y-030191X0220Y0244R270S1 -327GND C_STIC-2 A04X+057285Y-029813X0220Y0244R270S1 -327CU_CORE/3V3_RF U_HALL-1 A04X+050246Y-026752X0581Y0236R000S1 -327ER/TRIG_ANALOG U_HALL-2 A04X+050246Y-026004X0581Y0236R000S1 -327GND U_HALL-3 A04X+050984Y-026378X0581Y0236R000S1 +327R_BUCK/BUCK_FB R_FB1 -1 A04X+054537Y-039177X0213Y0252R270S1 +3273V3 R_FB1 -2 A04X+054537Y-038776X0213Y0252R270S1 +327/XBEE/XBEE_CTS U_XBEE-1 A04X+049783Y-047756X0669Y1063R180S1 +327/XBEE/XBEE_DIN U_XBEE-2 A04X+050783Y-047756X0669Y1063R180S1 +327XBEE/XBEE_DOUT U_XBEE-3 A04X+051783Y-047756X0669Y1063R180S1 +327/XBEE/XBEE_RTS U_XBEE-4 A04X+052783Y-047756X0669Y1063R180S1 +327/XBEE_ON_SLEEP U_XBEE-5 A04X+053783Y-047756X0669Y1063R180S1 +327BEE/XBEE_RESET U_XBEE-6 A04X+054783Y-047756X0669Y1063R180S1 +327/XBEE_SLEEP_RQ U_XBEE-7 A04X+054783Y-040787X0669Y1063R180S1 +327GND U_XBEE-8 A04X+053783Y-040787X0669Y1063R180S1 +3273V3 U_XBEE-9 A04X+052783Y-040787X0669Y1063R180S1 +3273V3 U_XBEE-10 A04X+051783Y-040787X0669Y1063R180S1 +327GND U_XBEE-11 A04X+050783Y-040787X0669Y1063R180S1 +327GND U_XBEE-12 A04X+049783Y-040787X0669Y1063R180S1 +327ER_BUCK/PWR_EN U_BUCK-1 A04X+058435Y-037697X0522Y0236R270S1 +327GND U_BUCK-2 A04X+058061Y-037697X0522Y0236R270S1 +327R_BUCK/BUCK_SW U_BUCK-3 A04X+057687Y-037697X0522Y0236R270S1 +327VSYS U_BUCK-4 A04X+057687Y-036801X0522Y0236R270S1 +327R_BUCK/BUCK_FB U_BUCK-5 A04X+058435Y-036801X0522Y0236R270S1 +3273V3 C_IMU_-1 A04X+049890Y-049567X0220Y0244R000S1 +327GND C_IMU_-2 A04X+050268Y-049567X0220Y0244R000S1 +327R_BUCK/BUCK_SW L_BUCK-1 A04X+056713Y-037697X0591Y1417R180S1 +3273V3 L_BUCK-2 A04X+055512Y-037697X0591Y1417R180S1 +3273V3 C_STIC-1 A04X+057285Y-029813X0220Y0244R090S1 +327GND C_STIC-2 A04X+057285Y-030191X0220Y0244R090S1 +3273V3 U_HALL-1 A04X+050172Y-025118X0581Y0236R180S1 +327ER/TRIG_ANALOG U_HALL-2 A04X+050172Y-025866X0581Y0236R180S1 +327GND U_HALL-3 A04X+049434Y-025492X0581Y0236R180S1 327R_BTN_INV_BASE Q_INV1-1 A04X+048843Y-034219X0581Y0236R000S1 327GND Q_INV1-2 A04X+048843Y-033470X0581Y0236R000S1 327WR_BTN_TRIGGER Q_INV1-3 A04X+049581Y-033844X0581Y0236R000S1 327ER/TRIG_ANALOG R_TRIG-1 A04X+051083Y-035724X0213Y0252R090S1 327IGGER/TRIG_ADC R_TRIG-2 A04X+051083Y-036126X0213Y0252R090S1 -327_CORE/MCU_BOOT R_BOOT-1 A04X+056915Y-039089X0213Y0252R270S1 -3273V3 R_BOOT-2 A04X+056915Y-038687X0213Y0252R270S1 +327CHARGER/CHG_TS R_TS1 -1 A04X+048142Y-039862X0213Y0252R180S1 +327GND R_TS1 -2 A04X+047740Y-039862X0213Y0252R180S1 999 diff --git a/PCB/v2.x/production/placement/snips_controller-all.pos b/PCB/v2.x/production/placement/snips_controller-all.pos index 076856a..dabc8d2 100644 --- a/PCB/v2.x/production/placement/snips_controller-all.pos +++ b/PCB/v2.x/production/placement/snips_controller-all.pos @@ -1,77 +1,78 @@ -### Footprint positions - created on 2026-10-30T18:10:03 ### +### Footprint positions - created on 2026-10-31T14:04:15 ### ### Printed by KiCad version 10.0.5 ## Unit = mm, Angle = deg. ## Side : All # Ref Val Package PosX PosY Rot Side BT1 PH_2-pin_battery_RIGHT-ANGLE_HORIZONTAL JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal 145.2000 -123.1000 0.0000 bottom -C_3V3_1 10µF C_0603_1608Metric 143.0750 -91.3750 0.0000 bottom -C_3V3_2 100nF C_0402_1005Metric 144.5550 -95.5050 90.0000 bottom -C_HALL1 100nF C_0402_1005Metric 128.8000 -64.6000 0.0000 bottom -C_IMU_1 100nF C_0402_1005Metric 142.2500 -69.0000 -90.0000 bottom -C_IMU_2 2.2µF C_0603_1608Metric 140.7500 -69.2500 -90.0000 bottom -C_IMU_3 10nF C_0402_1005Metric 144.7500 -70.0000 180.0000 bottom +C_BAT1 10µF C_0805_2012Metric 133.2000 -97.7500 0.0000 bottom +C_BUCK_IN1 10µF C_0805_2012Metric 146.5000 -90.6000 90.0000 bottom +C_BUCK_OUT1 22µF C_0805_2012Metric 138.0250 -95.7500 -90.0000 bottom +C_HALL1 100nF C_0402_1005Metric 129.4200 -63.8000 0.0000 bottom +C_IMU_1 100nF C_0402_1005Metric 127.2000 -125.9000 0.0000 bottom +C_IMU_2 2.2µF C_0603_1608Metric 124.7000 -125.7000 180.0000 bottom +C_IMU_3 10nF C_0402_1005Metric 127.1800 -128.5000 180.0000 bottom C_LATCH_G1 100nF C_0402_1005Metric 135.0050 -74.8900 180.0000 bottom -C_OLED_1 1µF C_0603_1608Metric 122.8000 -107.8000 180.0000 bottom -C_OLED_2 100nF C_0402_1005Metric 123.4800 -105.2000 180.0000 bottom -C_RF_BULK1 47µF C_1206_3216Metric 146.4950 -95.3950 90.0000 bottom -C_STICK1 100nF C_0402_1005Metric 145.5050 -76.2050 90.0000 bottom -C_TRIG1 100nF C_0402_1005Metric 131.5000 -91.7500 180.0000 bottom -C_VBUS1 1µF C_0603_1608Metric 140.5000 -88.7500 90.0000 bottom +C_STICK1 100nF C_0402_1005Metric 145.5050 -76.2050 -90.0000 bottom +C_SYS_1 10µF C_0805_2012Metric 134.7000 -94.2500 0.0000 bottom +C_SYS_2 100nF C_0402_1005Metric 131.2500 -94.7300 -90.0000 bottom +C_VIN_1 10µF C_0805_2012Metric 122.8000 -95.2500 180.0000 bottom +C_VIN_2 100nF C_0402_1005Metric 125.7500 -95.7700 -90.0000 bottom D_INV_ISO1 BAT54W-7-F SOT-323_SC-70 125.3113 -91.6275 -90.0000 bottom D_OR1 1N4148W D_SOD-123 128.4850 -78.6900 180.0000 bottom D_OR2 1N4148W D_SOD-123 135.2850 -72.4400 0.0000 bottom D_VBUS_TVS1 TPPESD5V0S1BA D_SOD-323 136.8950 -126.2450 0.0000 bottom -FB_RF1 600Ω@100MHz L_0603_1608Metric 139.8250 -91.3750 0.0000 bottom FID4 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 145.0000 -61.7500 0.0000 bottom FID5 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 122.7500 -128.2500 0.0000 bottom FID6 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 144.5000 -128.2500 0.0000 bottom +L_BUCK1 2.2µH L_Bourns-SRN4018 142.5250 -95.7500 180.0000 bottom Q_INV1 MMBT3904(RANGE:100-300) SOT-23 124.9988 -85.9650 0.0000 bottom Q_LATCH1 AO3400A SOT-23 134.3350 -77.8775 -90.0000 bottom Q_PWR1 AO3401A SOT-23 138.2850 -78.0025 -90.0000 bottom -R_BOOT_PU1 10kΩ R_0402_1005Metric 144.5650 -98.7750 90.0000 bottom -R_BTN_PU1 100kΩ R_0402_1005Metric 125.4100 -94.6000 0.0000 bottom +R_BTN_PU1 100kΩ R_0402_1005Metric 126.8712 -93.7650 180.0000 bottom R_CC1 5.1kΩ R_0402_1005Metric 130.7750 -123.8150 0.0000 bottom R_CC2 5.1kΩ R_0402_1005Metric 141.7750 -126.0650 0.0000 bottom +R_FB1 255kΩ R_0402_1005Metric 138.5250 -99.0000 90.0000 bottom +R_FB2 56.2kΩ R_0402_1005Metric 138.5250 -101.0000 -90.0000 bottom R_GATE1 100kΩ R_0402_1005Metric 140.7850 -76.4500 90.0000 bottom -R_I2C_SCL1 4.7kΩ R_0402_1005Metric 125.8750 -100.2500 90.0000 bottom -R_I2C_SDA1 4.7kΩ R_0402_1005Metric 125.8750 -102.5000 90.0000 bottom R_INV_BASE1 100kΩ R_0402_1005Metric 125.3713 -88.9650 180.0000 bottom R_INV_PU1 100kΩ R_0402_1005Metric 128.4613 -91.2150 90.0000 bottom +R_ISET1 604Ω R_0402_1005Metric 121.7900 -98.2500 180.0000 bottom R_LATCH_G1 1MΩ R_0402_1005Metric 132.2850 -74.4400 0.0000 bottom R_PWR_EN_PD1 100kΩ R_0402_1005Metric 140.9350 -80.2400 0.0000 bottom +R_STAT1 10kΩ R_0402_1005Metric 124.1600 -97.2500 180.0000 bottom +R_STAT2 10kΩ R_0402_1005Metric 133.3500 -100.0500 0.0000 bottom R_TRIG1 1kΩ R_0402_1005Metric 129.7500 -91.2500 -90.0000 bottom -R_VSYS1 200kΩ R_0402_1005Metric 133.7750 -91.6150 0.0000 bottom -R_VSYS2 100kΩ R_0402_1005Metric 136.0250 -91.6150 0.0000 bottom -SW_BOOT1 SKRPABE010 SW_Alps_SKRP 146.1750 -105.8750 0.0000 bottom -SW_RST1 SKRPABE010 SW_Alps_SKRP 146.1750 -101.7750 0.0000 bottom +R_TS1 10kΩ R_0402_1005Metric 121.7700 -101.2500 180.0000 bottom +R_VSET1 18kΩ R_0402_1005Metric 121.7700 -99.7500 180.0000 bottom SW_TRIG_DIG1 SKRTLAE010 SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010 135.0000 -61.8000 0.0000 bottom -U_HALL1 DRV5055A2QDBZR SOT-23 128.5625 -67.0000 0.0000 bottom -U_IMU1 ICM-42670-P LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y 144.7000 -67.8000 180.0000 bottom -U_MCU1 BT840XE BT840XE 134.2750 -106.7000 0.0000 bottom -C_BAT1 10µF C_0805_2012Metric 134.2000 -116.8150 0.0000 top -C_BUCK_IN1 10µF C_0805_2012Metric 139.9500 -114.3000 180.0000 top -C_BUCK_OUT1 10µF C_0805_2012Metric 131.4750 -109.8000 90.0000 top +U_BUCK1 TLV62569DBVR SOT-23-5 147.4750 -94.6125 90.0000 bottom +U_CHG1 BQ25185DLHR IC_BQ25185DLHR 128.7500 -96.2500 180.0000 bottom +U_HALL1 DRV5055A2QDBZR SOT-23 126.5000 -64.7500 180.0000 bottom +U_IMU1 ICM-42670-P LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y 129.8125 -127.2625 -90.0000 bottom +C_3V3_1 10µF C_0603_1608Metric 145.3000 -106.0000 90.0000 top +C_3V3_2 100nF C_0402_1005Metric 140.6000 -101.6000 90.0000 top +C_3V3_3 39pF C_0402_1005Metric 140.6000 -103.5500 90.0000 top C_DBNC1 100nF C_0402_1005Metric 123.6000 -125.2000 180.0000 top -C_RGB1 100nF C_0402_1005Metric 127.7500 -123.7500 0.0000 top -C_SYS_1 10µF C_0805_2012Metric 135.7000 -120.3150 0.0000 top -C_SYS_2 100nF C_0402_1005Metric 132.2500 -119.8350 90.0000 top -C_VIN_1 10µF C_0805_2012Metric 123.8000 -119.3150 180.0000 top -C_VIN_2 100nF C_0402_1005Metric 126.7500 -118.7950 90.0000 top +C_EN1 1µF C_0603_1608Metric 146.0000 -120.3000 0.0000 top +C_OLED_1 1µF C_0603_1608Metric 123.4000 -105.1000 180.0000 top +C_OLED_2 100nF C_0402_1005Metric 123.4000 -106.3000 180.0000 top +C_RGB1 100nF C_0402_1005Metric 125.8000 -124.6000 90.0000 top +C_TRIG1 100nF C_0402_1005Metric 131.6000 -103.3500 90.0000 top D_RGB1 SK6812MINI-HS-012 SK6812MINI-HS-012 128.7500 -127.0000 90.0000 top FID1 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 126.0000 -61.7500 0.0000 top FID2 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 143.7500 -61.7500 0.0000 top FID3 Fiducial_1mm_Mask2mm Fiducial_1mm_Mask2mm 148.5000 -121.0000 0.0000 top -J_STICK1 GuliKit_Thumbstick GuliKit_HallStick 135.0000 -78.5000 0.0000 top J_USB1 USB-C USB_C_Receptacle_HRO_TYPE-C-31-M-12 137.0000 -127.1500 0.0000 top -L_BUCK1 2.2µH L_Bourns-SRN4018 135.9750 -109.8000 180.0000 top -R_FB1 255kΩ R_0402_1005Metric 131.9750 -106.5500 -90.0000 top -R_FB2 56.2kΩ R_0402_1005Metric 133.7400 -106.7250 0.0000 top -R_ISET1 604Ω R_0402_1005Metric 122.2800 -116.5150 180.0000 top -R_RGB1 470Ω R_0402_1005Metric 127.7500 -122.6000 0.0000 top -R_STAT1 10kΩ R_0402_1005Metric 125.1600 -117.3150 180.0000 top -R_STAT2 10kΩ R_0402_1005Metric 134.3500 -114.5150 0.0000 top -R_TS1 10kΩ R_0402_1005Metric 122.2600 -114.5000 180.0000 top -R_VSET1 18kΩ R_0402_1005Metric 122.2600 -115.5000 180.0000 top +R_BOOT_PU1 10kΩ R_0402_1005Metric 145.8000 -109.4100 90.0000 top +R_EN_PU1 10kΩ R_0402_1005Metric 146.0000 -118.6000 0.0000 top +R_I2C_SCL1 4.7kΩ R_0402_1005Metric 127.2000 -106.9000 -90.0000 top +R_I2C_SDA1 4.7kΩ R_0402_1005Metric 125.5000 -105.7900 -90.0000 top +R_RGB1 470Ω R_0402_1005Metric 127.9000 -122.9900 90.0000 top +R_USB_DM1 27Ω R_0402_1005Metric 128.0200 -114.4600 90.0000 top +R_USB_DP1 27Ω R_0402_1005Metric 128.0200 -116.4000 90.0000 top +R_VSYS1 200kΩ R_0402_1005Metric 129.8000 -101.4100 -90.0000 top +R_VSYS2 100kΩ R_0402_1005Metric 130.0000 -103.4000 -90.0000 top +SW_BOOT1 SKRPABE010 SW_Alps_SKRP 147.1500 -114.5000 90.0000 top SW_MACRO1 SKRPABE010 SW_Alps_SKRP 125.9000 -95.3250 0.0000 top SW_MACRO2 SKRPABE010 SW_Alps_SKRP 135.0000 -95.3250 0.0000 top SW_MACRO3 SKRPABE010 SW_Alps_SKRP 144.1000 -95.3250 0.0000 top @@ -83,7 +84,6 @@ SW_THR_DN1 SKRTLAE010 SW_Push_1P1T-MP_NO_Horizo SW_THR_UP1 SKRTLAE010 SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010 121.8000 -73.5000 -90.0000 top SW_VOL_DN1 SKRTLAE010 SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010 148.2000 -83.5000 90.0000 top SW_VOL_UP1 SKRTLAE010 SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010 148.2000 -73.5000 90.0000 top -U_BUCK1 TLV62569DBVR SOT-23-5 140.9250 -110.9375 -90.0000 top -U_CHG1 BQ25185DLHR IC_BQ25185DLHR 129.7500 -118.3150 180.0000 top -U_OLED1 Qwiic_connector JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal 124.4000 -108.1250 0.0000 top +U_MCU1 ESP32-S3-MINI-1U-N8 ESP32-S3-MINI-1U 136.5000 -112.5000 -90.0000 top +U_OLED1 Qwiic_connector JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal 124.4000 -110.1250 0.0000 top ## End diff --git a/PCB/v2.x/production/placement/snips_controller-pnp_bottom.gbr b/PCB/v2.x/production/placement/snips_controller-pnp_bottom.gbr index c55d607..cd53f98 100644 --- a/PCB/v2.x/production/placement/snips_controller-pnp_bottom.gbr +++ b/PCB/v2.x/production/placement/snips_controller-pnp_bottom.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:03-07:00*% +%TF.CreationDate,2026-10-31T14:04:16-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Component,L4,Bot*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:03* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:16* %MOMM*% %LPD*% G01* @@ -33,20 +33,41 @@ D10* %TO.CVal,100kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X125410000Y-94600000D03* +%TO.CRot,0*% +X126871250Y-93764999D03* D11* -X126335000Y-94135000D02* -X126335000Y-95065000D01* -X124485000Y-95065000D01* -X124485000Y-94135000D01* -X126335000Y-94135000D01* +X127796250Y-93299999D02* +X127796250Y-94229999D01* +X125946250Y-94229999D01* +X125946250Y-93299999D01* +X127796250Y-93299999D01* D12* %TO.P,R_BTN_PU1,1*% -X124900000Y-94600000D03* +X127381250Y-93764999D03* D13* %TO.P,R_BTN_PU1,2*% -X125920000Y-94600000D03* +X126361250Y-93764999D03* +%TD*% +D10* +%TO.C,C_SYS_1*% +%TO.CFtp,C_0805_2012Metric*% +%TO.CVal,10µF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,180*% +X134700000Y-94250000D03* +D11* +X136395000Y-93275000D02* +X136395000Y-95225000D01* +X133005000Y-95225000D01* +X133005000Y-93275000D01* +X136395000Y-93275000D01* +D12* +%TO.P,C_SYS_1,1*% +X133750000Y-94250000D03* +D13* +%TO.P,C_SYS_1,2*% +X135650000Y-94250000D03* %TD*% D10* %TO.C,Q_PWR1*% @@ -84,26 +105,6 @@ X139235000Y-77065000D03* X138285000Y-78940000D03* %TD*% D10* -%TO.C,C_VBUS1*% -%TO.CFtp,C_0603_1608Metric*% -%TO.CVal,1µF*% -%TO.CMnt,SMD*% -%TO.CRot,-90*% -X140500000Y-88750000D03* -D11* -X141225000Y-87275000D02* -X141225000Y-90225000D01* -X139775000Y-90225000D01* -X139775000Y-87275000D01* -X141225000Y-87275000D01* -D12* -%TO.P,C_VBUS1,1*% -X140500000Y-89525000D03* -D13* -%TO.P,C_VBUS1,2*% -X140500000Y-87975000D03* -%TD*% -D10* %TO.C,D_VBUS_TVS1*% %TO.CFtp,D_SOD-323*% %TO.CVal,TPPESD5V0S1BA*% @@ -164,24 +165,46 @@ D13* X145000000Y-61750000D03* %TD*% D10* -%TO.C,C_OLED_1*% -%TO.CFtp,C_0603_1608Metric*% -%TO.CVal,1µF*% +%TO.C,C_VIN_2*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,90*% +X125750000Y-95770000D03* +D11* +X126205000Y-94865000D02* +X126205000Y-96675000D01* +X125295000Y-96675000D01* +X125295000Y-94865000D01* +X126205000Y-94865000D01* +D12* +%TO.P,C_VIN_2,1*% +X125750000Y-95290000D03* +D13* +%TO.P,C_VIN_2,2*% +X125750000Y-96250000D03* +%TD*% +D10* +%TO.C,C_VIN_1*% +%TO.CFtp,C_0805_2012Metric*% +%TO.CVal,10µF*% +%TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% %TO.CRot,0*% -X122800000Y-107800000D03* +X122800000Y-95250000D03* D11* -X124275000Y-107075000D02* -X124275000Y-108525000D01* -X121325000Y-108525000D01* -X121325000Y-107075000D01* -X124275000Y-107075000D01* +X124495000Y-94275000D02* +X124495000Y-96225000D01* +X121105000Y-96225000D01* +X121105000Y-94275000D01* +X124495000Y-94275000D01* D12* -%TO.P,C_OLED_1,1*% -X123575000Y-107800000D03* +%TO.P,C_VIN_1,1*% +X123750000Y-95250000D03* D13* -%TO.P,C_OLED_1,2*% -X122025000Y-107800000D03* +%TO.P,C_VIN_1,2*% +X121850000Y-95250000D03* %TD*% D10* %TO.C,FID6*% @@ -202,6 +225,27 @@ D13* X144500000Y-128250000D03* %TD*% D10* +%TO.C,C_BUCK_OUT1*% +%TO.CFtp,C_0805_2012Metric*% +%TO.CVal,22µF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,90*% +X138025000Y-95750000D03* +D11* +X139000000Y-94055000D02* +X139000000Y-97445000D01* +X137050000Y-97445000D01* +X137050000Y-94055000D01* +X139000000Y-94055000D01* +D12* +%TO.P,C_BUCK_OUT1,1*% +X138025000Y-94800000D03* +D13* +%TO.P,C_BUCK_OUT1,2*% +X138025000Y-96700000D03* +%TD*% +D10* %TO.C,D_INV_ISO1*% %TO.CFtp,SOT-323_SC-70*% %TO.CVal,BAT54W-7-F*% @@ -297,110 +341,69 @@ D13* X122750000Y-128250000D03* %TD*% D10* -%TO.C,SW_BOOT1*% -%TO.CFtp,SW_Alps_SKRP*% -%TO.CVal,SKRPABE010*% -%TO.CMnt,SMD*% -%TO.CRot,180*% -X146175000Y-105875000D03* -D11* -X149020000Y-104030000D02* -X149020000Y-107720000D01* -X143330000Y-107720000D01* -X143330000Y-104030000D01* -X149020000Y-104030000D01* -D12* -%TO.P,SW_BOOT1,1*% -X144100000Y-106950000D03* -X148250000Y-106950000D03* -D13* -%TO.P,SW_BOOT1,2*% -X144100000Y-104800000D03* -X148250000Y-104800000D03* -%TD*% -D10* -%TO.C,C_TRIG1*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% -%TO.CMnt,SMD*% -%TO.CRot,0*% -X131500000Y-91750000D03* -D11* -X132405000Y-91295000D02* -X132405000Y-92205000D01* -X130595000Y-92205000D01* -X130595000Y-91295000D01* -X132405000Y-91295000D01* -D12* -%TO.P,C_TRIG1,1*% -X131980000Y-91750000D03* -D13* -%TO.P,C_TRIG1,2*% -X131020000Y-91750000D03* -%TD*% -D10* -%TO.C,FB_RF1*% -%TO.CFtp,L_0603_1608Metric*% -%TO.CVal,600Ω@100MHz*% -%TO.CMnt,SMD*% -%TO.CRot,180*% -X139825000Y-91375000D03* -D11* -X141300000Y-90650000D02* -X141300000Y-92100000D01* -X138350000Y-92100000D01* -X138350000Y-90650000D01* -X141300000Y-90650000D01* -D12* -%TO.P,FB_RF1,1*% -X139037500Y-91375000D03* -D13* -%TO.P,FB_RF1,2*% -X140612500Y-91375000D03* -%TD*% -D10* %TO.C,U_IMU1*% %TO.CFtp,LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y*% %TO.CVal,ICM-42670-P*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X144700000Y-67800000D03* +%TO.CRot,90*% +X129812500Y-127262500D03* D11* -X146445000Y-66305000D02* -X146445000Y-69295000D01* -X142955000Y-69295000D01* -X142955000Y-66305000D01* -X146445000Y-66305000D01* +X131307500Y-125517500D02* +X131307500Y-129007500D01* +X128317500Y-129007500D01* +X128317500Y-125517500D01* +X131307500Y-125517500D01* D12* %TO.P,U_IMU1,1*% -X145862500Y-67050000D03* +X129062500Y-126100000D03* D13* %TO.P,U_IMU1,2*% -X145862500Y-67550000D03* +X129562500Y-126100000D03* %TO.P,U_IMU1,3*% -X145862500Y-68050000D03* +X130062500Y-126100000D03* %TO.P,U_IMU1,4*% -X145862500Y-68550000D03* +X130562500Y-126100000D03* %TO.P,U_IMU1,5*% -X145200000Y-68712500D03* +X130725000Y-126762500D03* %TO.P,U_IMU1,6*% -X144700000Y-68712500D03* +X130725000Y-127262500D03* %TO.P,U_IMU1,7*% -X144200000Y-68712500D03* +X130725000Y-127762500D03* %TO.P,U_IMU1,8*% -X143537500Y-68550000D03* +X130562500Y-128425000D03* %TO.P,U_IMU1,9*% -X143537500Y-68050000D03* +X130062500Y-128425000D03* %TO.P,U_IMU1,10*% -X143537500Y-67550000D03* +X129562500Y-128425000D03* %TO.P,U_IMU1,11*% -X143537500Y-67050000D03* +X129062500Y-128425000D03* %TO.P,U_IMU1,12*% -X144200000Y-66887500D03* +X128900000Y-127762500D03* %TO.P,U_IMU1,13*% -X144700000Y-66887500D03* +X128900000Y-127262500D03* %TO.P,U_IMU1,14*% -X145200000Y-66887500D03* +X128900000Y-126762500D03* +%TD*% +D10* +%TO.C,C_BUCK_IN1*% +%TO.CFtp,C_0805_2012Metric*% +%TO.CVal,10µF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,-90*% +X146500000Y-90600000D03* +D11* +X147475000Y-88905000D02* +X147475000Y-92295000D01* +X145525000Y-92295000D01* +X145525000Y-88905000D01* +X147475000Y-88905000D01* +D12* +%TO.P,C_BUCK_IN1,1*% +X146500000Y-91550000D03* +D13* +%TO.P,C_BUCK_IN1,2*% +X146500000Y-89650000D03* %TD*% D10* %TO.C,C_LATCH_G1*% @@ -430,19 +433,19 @@ D10* %TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% %TO.CRot,180*% -X128800000Y-64600000D03* +X129420000Y-63800000D03* D11* -X129705000Y-64145000D02* -X129705000Y-65055000D01* -X127895000Y-65055000D01* -X127895000Y-64145000D01* -X129705000Y-64145000D01* +X130325000Y-63345000D02* +X130325000Y-64255000D01* +X128515000Y-64255000D01* +X128515000Y-63345000D01* +X130325000Y-63345000D01* D12* %TO.P,C_HALL1,1*% -X128320000Y-64600000D03* +X128940000Y-63800000D03* D13* %TO.P,C_HALL1,2*% -X129280000Y-64600000D03* +X129900000Y-63800000D03* %TD*% D10* %TO.C,R_INV_BASE1*% @@ -571,24 +574,130 @@ X135285000Y-76940000D03* X134335000Y-78815000D03* %TD*% D10* +%TO.C,C_SYS_2*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,90*% +X131250000Y-94730000D03* +D11* +X131705000Y-93825000D02* +X131705000Y-95635000D01* +X130795000Y-95635000D01* +X130795000Y-93825000D01* +X131705000Y-93825000D01* +D12* +%TO.P,C_SYS_2,1*% +X131250000Y-94250000D03* +D13* +%TO.P,C_SYS_2,2*% +X131250000Y-95210000D03* +%TD*% +D10* %TO.C,C_IMU_2*% %TO.CFtp,C_0603_1608Metric*% %TO.CVal,2.2µF*% %TO.CMnt,SMD*% -%TO.CRot,90*% -X140750000Y-69250000D03* +%TO.CRot,0*% +X124700000Y-125700000D03* D11* -X141475000Y-67775000D02* -X141475000Y-70725000D01* -X140025000Y-70725000D01* -X140025000Y-67775000D01* -X141475000Y-67775000D01* +X126175000Y-124975000D02* +X126175000Y-126425000D01* +X123225000Y-126425000D01* +X123225000Y-124975000D01* +X126175000Y-124975000D01* D12* %TO.P,C_IMU_2,1*% -X140750000Y-68475000D03* +X125475000Y-125700000D03* D13* %TO.P,C_IMU_2,2*% -X140750000Y-70025000D03* +X123925000Y-125700000D03* +%TD*% +D10* +%TO.C,C_BAT1*% +%TO.CFtp,C_0805_2012Metric*% +%TO.CVal,10µF*% +%TO.CLbN,Capacitor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,180*% +X133200000Y-97750000D03* +D11* +X134895000Y-96775000D02* +X134895000Y-98725000D01* +X131505000Y-98725000D01* +X131505000Y-96775000D01* +X134895000Y-96775000D01* +D12* +%TO.P,C_BAT1,1*% +X132250000Y-97750000D03* +D13* +%TO.P,C_BAT1,2*% +X134150000Y-97750000D03* +%TD*% +D10* +%TO.C,U_CHG1*% +%TO.CFtp,IC_BQ25185DLHR*% +%TO.CVal,BQ25185DLHR*% +%TO.CLbN,BQ25185DLHR*% +%TO.CMnt,SMD*% +%TO.CRot,0*% +X128750000Y-96250000D03* +D11* +X130295000Y-95005000D02* +X130295000Y-97495000D01* +X127205000Y-97495000D01* +X127205000Y-95005000D01* +X130295000Y-95005000D01* +D12* +%TO.P,U_CHG1,1,SYS_1*% +X129800000Y-95450000D03* +D13* +%TO.P,U_CHG1,2,BAT_2*% +X129800000Y-95850000D03* +%TO.P,U_CHG1,3,STAT2_3*% +X129800000Y-96250000D03* +%TO.P,U_CHG1,4,~{CE}_4*% +X129800000Y-96650000D03* +%TO.P,U_CHG1,5,GND_5*% +X129800000Y-97050000D03* +%TO.P,U_CHG1,6,TS/MR_6*% +X127700000Y-97050000D03* +%TO.P,U_CHG1,7,ILIM/VSET_7*% +X127700000Y-96650000D03* +%TO.P,U_CHG1,8,ISET_8*% +X127700000Y-96250000D03* +%TO.P,U_CHG1,9,STAT1_9*% +X127700000Y-95850000D03* +%TO.P,U_CHG1,10,IN_10*% +X127700000Y-95450000D03* +%TO.P,U_CHG1,11,THERMAL_PAD_11*% +X128750000Y-96250000D03* +%TO.P,U_CHG1,12*% +X128750000Y-95750000D03* +%TO.P,U_CHG1,13*% +X128750000Y-96750000D03* +%TD*% +D10* +%TO.C,R_STAT2*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,10kΩ*% +%TO.CLbN,Resistor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,180*% +X133350000Y-100050000D03* +D11* +X134275000Y-99585000D02* +X134275000Y-100515000D01* +X132425000Y-100515000D01* +X132425000Y-99585000D01* +X134275000Y-99585000D01* +D12* +%TO.P,R_STAT2,1*% +X132840000Y-100050000D03* +D13* +%TO.P,R_STAT2,2*% +X133860000Y-100050000D03* %TD*% D10* %TO.C,R_CC2*% @@ -612,27 +721,6 @@ D13* X142285000Y-126065000D03* %TD*% D10* -%TO.C,C_OLED_2*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% -%TO.CLbN,Capacitor_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,0*% -X123480000Y-105200000D03* -D11* -X124385000Y-104745000D02* -X124385000Y-105655000D01* -X122575000Y-105655000D01* -X122575000Y-104745000D01* -X124385000Y-104745000D01* -D12* -%TO.P,C_OLED_2,1*% -X123960000Y-105200000D03* -D13* -%TO.P,C_OLED_2,2*% -X123000000Y-105200000D03* -%TD*% -D10* %TO.C,D_OR2*% %TO.CFtp,D_SOD-123*% %TO.CVal,1N4148W*% @@ -675,377 +763,230 @@ D13* X132795000Y-74440000D03* %TD*% D10* -%TO.C,U_MCU1*% -%TO.CFtp,BT840XE*% -%TO.CVal,BT840XE*% -%TO.CMnt,SMD*% -%TO.CRot,180*% -X134275000Y-106700000D03* -D11* -X142520000Y-92455000D02* -X142520000Y-120945000D01* -X126530000Y-120945000D01* -X126530000Y-92455000D01* -X142520000Y-92455000D01* -D12* -%TO.P,U_MCU1,1*% -X127900000Y-101500000D03* -%TO.P,U_MCU1,A1*% -X132525000Y-99500000D03* -D13* -%TO.P,U_MCU1,2*% -X127900000Y-100400000D03* -%TO.P,U_MCU1,3*% -X127900000Y-99300000D03* -%TO.P,U_MCU1,4*% -X127900000Y-98200000D03* -%TO.P,U_MCU1,5*% -X127900000Y-97100000D03* -%TO.P,U_MCU1,6*% -X127900000Y-96000000D03* -%TO.P,U_MCU1,7*% -X127900000Y-94900000D03* -%TO.P,U_MCU1,8*% -X127900000Y-93800000D03* -%TO.P,U_MCU1,9*% -X141650000Y-93800000D03* -%TO.P,U_MCU1,10*% -X141650000Y-94900000D03* -%TO.P,U_MCU1,11*% -X141650000Y-96000000D03* -%TO.P,U_MCU1,12*% -X141650000Y-97100000D03* -%TO.P,U_MCU1,13*% -X141650000Y-98200000D03* -%TO.P,U_MCU1,14*% -X141650000Y-99300000D03* -%TO.P,U_MCU1,15*% -X141650000Y-100400000D03* -%TO.P,U_MCU1,16*% -X141650000Y-101500000D03* -%TO.P,U_MCU1,A0*% -X132525000Y-100700000D03* -%TO.P,U_MCU1,A2*% -X132525000Y-98300000D03* -%TO.P,U_MCU1,A3*% -X132525000Y-97100000D03* -%TO.P,U_MCU1,A4*% -X132525000Y-95900000D03* -%TO.P,U_MCU1,A5*% -X132525000Y-94700000D03* -%TO.P,U_MCU1,A6*% -X132525000Y-93500000D03* -%TO.P,U_MCU1,B0*% -X134025000Y-100700000D03* -%TO.P,U_MCU1,B1*% -X134025000Y-99500000D03* -%TO.P,U_MCU1,B2*% -X134025000Y-98300000D03* -%TO.P,U_MCU1,B3*% -X134025000Y-97100000D03* -%TO.P,U_MCU1,B4*% -X134025000Y-95900000D03* -%TO.P,U_MCU1,B5*% -X134025000Y-94700000D03* -%TO.P,U_MCU1,B6*% -X134025000Y-93500000D03* -%TO.P,U_MCU1,C0*% -X135525000Y-100700000D03* -%TO.P,U_MCU1,C1*% -X135525000Y-99500000D03* -%TO.P,U_MCU1,C2*% -X135525000Y-98300000D03* -%TO.P,U_MCU1,C3*% -X135525000Y-97100000D03* -%TO.P,U_MCU1,C4*% -X135525000Y-95900000D03* -%TO.P,U_MCU1,C5*% -X135525000Y-94700000D03* -%TO.P,U_MCU1,C6*% -X135525000Y-93500000D03* -%TO.P,U_MCU1,D0*% -X137025000Y-100700000D03* -%TO.P,U_MCU1,D1*% -X137025000Y-99500000D03* -%TO.P,U_MCU1,D2*% -X137025000Y-98300000D03* -%TO.P,U_MCU1,D3*% -X137025000Y-97100000D03* -%TO.P,U_MCU1,D4*% -X137025000Y-95900000D03* -%TO.P,U_MCU1,D5*% -X137025000Y-94700000D03* -%TO.P,U_MCU1,D6*% -X137025000Y-93500000D03* -%TO.P,U_MCU1,E0*% -X138525000Y-100700000D03* -%TO.P,U_MCU1,E1*% -X138525000Y-99500000D03* -%TO.P,U_MCU1,E2*% -X138525000Y-98300000D03* -%TO.P,U_MCU1,E3*% -X138525000Y-97100000D03* -%TO.P,U_MCU1,E4*% -X138525000Y-95900000D03* -%TO.P,U_MCU1,E5*% -X138525000Y-94700000D03* -%TO.P,U_MCU1,E6*% -X138525000Y-93500000D03* -%TO.P,U_MCU1,F0*% -X131400000Y-102700000D03* -%TO.P,U_MCU1,F1*% -X133650000Y-102700000D03* -%TO.P,U_MCU1,F2*% -X135900000Y-102700000D03* -%TO.P,U_MCU1,F3*% -X138150000Y-102700000D03* -%TO.P,U_MCU1,F4*% -X140025000Y-95900000D03* -%TO.P,U_MCU1,F5*% -X140025000Y-94700000D03* -%TO.P,U_MCU1,F6*% -X140025000Y-93500000D03* -%TO.P,U_MCU1,Z0*% -X131025000Y-100700000D03* -%TO.P,U_MCU1,Z1*% -X131025000Y-99500000D03* -%TO.P,U_MCU1,Z2*% -X131025000Y-98300000D03* -%TO.P,U_MCU1,Z3*% -X131025000Y-97100000D03* -%TO.P,U_MCU1,Z4*% -X131025000Y-95900000D03* -%TO.P,U_MCU1,Z5*% -X131025000Y-94700000D03* -%TO.P,U_MCU1,Z6*% -X131025000Y-93500000D03* -%TD*% -D10* -%TO.C,C_IMU_3*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,10nF*% +%TO.C,R_FB2*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,56.2kΩ*% +%TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X144750000Y-70000000D03* +%TO.CRot,90*% +X138525000Y-101000000D03* D11* -X145655000Y-69545000D02* -X145655000Y-70455000D01* -X143845000Y-70455000D01* -X143845000Y-69545000D01* -X145655000Y-69545000D01* +X138990000Y-100075000D02* +X138990000Y-101925000D01* +X138060000Y-101925000D01* +X138060000Y-100075000D01* +X138990000Y-100075000D01* D12* -%TO.P,C_IMU_3,1*% -X145230000Y-70000000D03* +%TO.P,R_FB2,1*% +X138525000Y-100490000D03* D13* -%TO.P,C_IMU_3,2*% -X144270000Y-70000000D03* +%TO.P,R_FB2,2*% +X138525000Y-101510000D03* %TD*% D10* -%TO.C,R_CC1*% +%TO.C,R_VSET1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,5.1kΩ*% +%TO.CVal,18kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X130775000Y-123815000D03* +%TO.CRot,0*% +X121770000Y-99750000D03* D11* -X131700000Y-123350000D02* -X131700000Y-124280000D01* -X129850000Y-124280000D01* -X129850000Y-123350000D01* -X131700000Y-123350000D01* +X122695000Y-99285000D02* +X122695000Y-100215000D01* +X120845000Y-100215000D01* +X120845000Y-99285000D01* +X122695000Y-99285000D01* D12* -%TO.P,R_CC1,1*% -X130265000Y-123815000D03* +%TO.P,R_VSET1,1*% +X122280000Y-99750000D03* D13* -%TO.P,R_CC1,2*% -X131285000Y-123815000D03* +%TO.P,R_VSET1,2*% +X121260000Y-99750000D03* %TD*% D10* -%TO.C,C_3V3_2*% +%TO.C,C_IMU_3*% %TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% -%TO.CLbN,Capacitor_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,-90*% -X144555000Y-95505000D03* -D11* -X145010000Y-94600000D02* -X145010000Y-96410000D01* -X144100000Y-96410000D01* -X144100000Y-94600000D01* -X145010000Y-94600000D01* -D12* -%TO.P,C_3V3_2,1*% -X144555000Y-95985000D03* -D13* -%TO.P,C_3V3_2,2*% -X144555000Y-95025000D03* -%TD*% -D10* -%TO.C,C_3V3_1*% -%TO.CFtp,C_0603_1608Metric*% -%TO.CVal,10µF*% -%TO.CLbN,Capacitor_SMD*% +%TO.CVal,10nF*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X143075000Y-91375000D03* +%TO.CRot,0*% +X127180000Y-128500000D03* D11* -X144550000Y-90650000D02* -X144550000Y-92100000D01* -X141600000Y-92100000D01* -X141600000Y-90650000D01* -X144550000Y-90650000D01* +X128085000Y-128045000D02* +X128085000Y-128955000D01* +X126275000Y-128955000D01* +X126275000Y-128045000D01* +X128085000Y-128045000D01* D12* -%TO.P,C_3V3_1,1*% -X142300000Y-91375000D03* +%TO.P,C_IMU_3,1*% +X127660000Y-128500000D03* D13* -%TO.P,C_3V3_1,2*% -X143850000Y-91375000D03* +%TO.P,C_IMU_3,2*% +X126700000Y-128500000D03* %TD*% D10* -%TO.C,R_VSYS1*% +%TO.C,R_STAT1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,200kΩ*% +%TO.CVal,10kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X133775000Y-91615000D03* +%TO.CRot,0*% +X124160000Y-97250000D03* D11* -X134700000Y-91150000D02* -X134700000Y-92080000D01* -X132850000Y-92080000D01* -X132850000Y-91150000D01* -X134700000Y-91150000D01* +X125085000Y-96785000D02* +X125085000Y-97715000D01* +X123235000Y-97715000D01* +X123235000Y-96785000D01* +X125085000Y-96785000D01* D12* -%TO.P,R_VSYS1,1*% -X133265000Y-91615000D03* +%TO.P,R_STAT1,1*% +X124670000Y-97250000D03* D13* -%TO.P,R_VSYS1,2*% -X134285000Y-91615000D03* +%TO.P,R_STAT1,2*% +X123650000Y-97250000D03* %TD*% D10* -%TO.C,C_RF_BULK1*% -%TO.CFtp,C_1206_3216Metric*% -%TO.CVal,47µF*% +%TO.C,R_ISET1*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,604Ω*% +%TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,-90*% -X146495000Y-95395000D03* +%TO.CRot,0*% +X121790000Y-98250000D03* D11* -X147640000Y-93100000D02* -X147640000Y-97690000D01* -X145350000Y-97690000D01* -X145350000Y-93100000D01* -X147640000Y-93100000D01* +X122715000Y-97785000D02* +X122715000Y-98715000D01* +X120865000Y-98715000D01* +X120865000Y-97785000D01* +X122715000Y-97785000D01* D12* -%TO.P,C_RF_BULK1,1*% -X146495000Y-96870000D03* +%TO.P,R_ISET1,1*% +X122300000Y-98250000D03* D13* -%TO.P,C_RF_BULK1,2*% -X146495000Y-93920000D03* +%TO.P,R_ISET1,2*% +X121280000Y-98250000D03* %TD*% D10* -%TO.C,R_I2C_SDA1*% +%TO.C,R_CC1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,4.7kΩ*% +%TO.CVal,5.1kΩ*% +%TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,-90*% -X125875000Y-102500000D03* +%TO.CRot,180*% +X130775000Y-123815000D03* D11* -X126340000Y-101575000D02* -X126340000Y-103425000D01* -X125410000Y-103425000D01* -X125410000Y-101575000D01* -X126340000Y-101575000D01* +X131700000Y-123350000D02* +X131700000Y-124280000D01* +X129850000Y-124280000D01* +X129850000Y-123350000D01* +X131700000Y-123350000D01* D12* -%TO.P,R_I2C_SDA1,1*% -X125875000Y-103010000D03* +%TO.P,R_CC1,1*% +X130265000Y-123815000D03* D13* -%TO.P,R_I2C_SDA1,2*% -X125875000Y-101990000D03* +%TO.P,R_CC1,2*% +X131285000Y-123815000D03* %TD*% D10* -%TO.C,R_I2C_SCL1*% +%TO.C,R_FB1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,4.7kΩ*% +%TO.CVal,255kΩ*% +%TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% %TO.CRot,-90*% -X125875000Y-100250000D03* +X138525000Y-99000000D03* D11* -X126340000Y-99325000D02* -X126340000Y-101175000D01* -X125410000Y-101175000D01* -X125410000Y-99325000D01* -X126340000Y-99325000D01* +X138990000Y-98075000D02* +X138990000Y-99925000D01* +X138060000Y-99925000D01* +X138060000Y-98075000D01* +X138990000Y-98075000D01* D12* -%TO.P,R_I2C_SCL1,1*% -X125875000Y-100760000D03* +%TO.P,R_FB1,1*% +X138525000Y-99510000D03* D13* -%TO.P,R_I2C_SCL1,2*% -X125875000Y-99740000D03* +%TO.P,R_FB1,2*% +X138525000Y-98490000D03* %TD*% D10* -%TO.C,SW_RST1*% -%TO.CFtp,SW_Alps_SKRP*% -%TO.CVal,SKRPABE010*% +%TO.C,U_BUCK1*% +%TO.CFtp,SOT-23-5*% +%TO.CVal,TLV62569DBVR*% +%TO.CLbN,Package_TO_SOT_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X146175000Y-101775000D03* +%TO.CRot,-90*% +X147475000Y-94612500D03* D11* -X149020000Y-99930000D02* -X149020000Y-103620000D01* -X143330000Y-103620000D01* -X143330000Y-99930000D01* -X149020000Y-99930000D01* +X147080000Y-92567500D02* +X147080000Y-93567500D01* +X147870000Y-93567500D01* +X147870000Y-92567500D01* +X148970000Y-92567500D01* +X148970000Y-93567500D01* +X149170000Y-93567500D01* +X149170000Y-95657500D01* +X148970000Y-95657500D01* +X148970000Y-96657500D01* +X145980000Y-96657500D01* +X145980000Y-95657500D01* +X145780000Y-95657500D01* +X145780000Y-93567500D01* +X145980000Y-93567500D01* +X145980000Y-92567500D01* +X147080000Y-92567500D01* D12* -%TO.P,SW_RST1,1*% -X144100000Y-102850000D03* -X148250000Y-102850000D03* +%TO.P,U_BUCK1,1,EN_1*% +X148425000Y-95750000D03* D13* -%TO.P,SW_RST1,2*% -X144100000Y-100700000D03* -X148250000Y-100700000D03* +%TO.P,U_BUCK1,2,GND_2*% +X147475000Y-95750000D03* +%TO.P,U_BUCK1,3,SW_3*% +X146525000Y-95750000D03* +%TO.P,U_BUCK1,4,VIN_4*% +X146525000Y-93475000D03* +%TO.P,U_BUCK1,5,FB_5*% +X148425000Y-93475000D03* %TD*% D10* %TO.C,C_IMU_1*% %TO.CFtp,C_0402_1005Metric*% %TO.CVal,100nF*% %TO.CMnt,SMD*% -%TO.CRot,90*% -X142250000Y-69000000D03* +%TO.CRot,180*% +X127200000Y-125900000D03* D11* -X142705000Y-68095000D02* -X142705000Y-69905000D01* -X141795000Y-69905000D01* -X141795000Y-68095000D01* -X142705000Y-68095000D01* +X128105000Y-125445000D02* +X128105000Y-126355000D01* +X126295000Y-126355000D01* +X126295000Y-125445000D01* +X128105000Y-125445000D01* D12* %TO.P,C_IMU_1,1*% -X142250000Y-68520000D03* +X126720000Y-125900000D03* D13* %TO.P,C_IMU_1,2*% -X142250000Y-69480000D03* +X127680000Y-125900000D03* %TD*% D10* -%TO.C,R_VSYS2*% -%TO.CFtp,R_0402_1005Metric*% -%TO.CVal,100kΩ*% -%TO.CLbN,Resistor_SMD*% +%TO.C,L_BUCK1*% +%TO.CFtp,L_Bourns-SRN4018*% +%TO.CVal,2.2µH*% +%TO.CLbN,Inductor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X136025000Y-91615000D03* +%TO.CRot,0*% +X142525000Y-95750000D03* D11* -X136950000Y-91150000D02* -X136950000Y-92080000D01* -X135100000Y-92080000D01* -X135100000Y-91150000D01* -X136950000Y-91150000D01* +X145050000Y-93505000D02* +X145050000Y-97995000D01* +X140000000Y-97995000D01* +X140000000Y-93505000D01* +X145050000Y-93505000D01* D12* -%TO.P,R_VSYS2,1*% -X135515000Y-91615000D03* +%TO.P,L_BUCK1,1,1_1*% +X144050000Y-95750000D03* D13* -%TO.P,R_VSYS2,2*% -X136535000Y-91615000D03* +%TO.P,L_BUCK1,2,2_2*% +X141000000Y-95750000D03* %TD*% D10* %TO.C,C_STICK1*% @@ -1053,7 +994,7 @@ D10* %TO.CVal,100nF*% %TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,-90*% +%TO.CRot,90*% X145505000Y-76205000D03* D11* X145960000Y-75300000D02* @@ -1063,44 +1004,44 @@ X145050000Y-75300000D01* X145960000Y-75300000D01* D12* %TO.P,C_STICK1,1*% -X145505000Y-76685000D03* +X145505000Y-75725000D03* D13* %TO.P,C_STICK1,2*% -X145505000Y-75725000D03* +X145505000Y-76685000D03* %TD*% D10* %TO.C,U_HALL1*% %TO.CFtp,SOT-23*% %TO.CVal,DRV5055A2QDBZR*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X128562500Y-67000000D03* +%TO.CRot,0*% +X126500000Y-64750000D03* D11* -X129457500Y-65305000D02* -X129457500Y-66455000D01* -X130487500Y-66455000D01* -X130487500Y-67545000D01* -X129457500Y-67545000D01* -X129457500Y-68695000D01* -X127667500Y-68695000D01* -X127667500Y-68495000D01* -X126637500Y-68495000D01* -X126637500Y-67395000D01* -X127667500Y-67395000D01* -X127667500Y-66605000D01* -X126637500Y-66605000D01* -X126637500Y-65505000D01* -X127667500Y-65505000D01* -X127667500Y-65305000D01* -X129457500Y-65305000D01* +X127395000Y-63055000D02* +X127395000Y-63255000D01* +X128425000Y-63255000D01* +X128425000Y-64355000D01* +X127395000Y-64355000D01* +X127395000Y-65145000D01* +X128425000Y-65145000D01* +X128425000Y-66245000D01* +X127395000Y-66245000D01* +X127395000Y-66445000D01* +X125605000Y-66445000D01* +X125605000Y-65295000D01* +X124575000Y-65295000D01* +X124575000Y-64205000D01* +X125605000Y-64205000D01* +X125605000Y-63055000D01* +X127395000Y-63055000D01* D12* %TO.P,U_HALL1,1*% -X127625000Y-67950000D03* +X127437500Y-63800000D03* D13* %TO.P,U_HALL1,2*% -X127625000Y-66050000D03* +X127437500Y-65700000D03* %TO.P,U_HALL1,3*% -X129500000Y-67000000D03* +X125562500Y-64750000D03* %TD*% D10* %TO.C,Q_INV1*% @@ -1158,24 +1099,24 @@ D13* X129750000Y-91760000D03* %TD*% D10* -%TO.C,R_BOOT_PU1*% +%TO.C,R_TS1*% %TO.CFtp,R_0402_1005Metric*% %TO.CVal,10kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,-90*% -X144565000Y-98775000D03* +%TO.CRot,0*% +X121770000Y-101250000D03* D11* -X145030000Y-97850000D02* -X145030000Y-99700000D01* -X144100000Y-99700000D01* -X144100000Y-97850000D01* -X145030000Y-97850000D01* +X122695000Y-100785000D02* +X122695000Y-101715000D01* +X120845000Y-101715000D01* +X120845000Y-100785000D01* +X122695000Y-100785000D01* D12* -%TO.P,R_BOOT_PU1,1*% -X144565000Y-99285000D03* +%TO.P,R_TS1,1*% +X122280000Y-101250000D03* D13* -%TO.P,R_BOOT_PU1,2*% -X144565000Y-98265000D03* +%TO.P,R_TS1,2*% +X121260000Y-101250000D03* %TD*% M02* diff --git a/PCB/v2.x/production/placement/snips_controller-pnp_top.gbr b/PCB/v2.x/production/placement/snips_controller-pnp_top.gbr index 918ba13..7aec53a 100644 --- a/PCB/v2.x/production/placement/snips_controller-pnp_top.gbr +++ b/PCB/v2.x/production/placement/snips_controller-pnp_top.gbr @@ -1,12 +1,12 @@ %TF.GenerationSoftware,KiCad,Pcbnew,10.0.5*% -%TF.CreationDate,2026-10-30T18:10:03-07:00*% +%TF.CreationDate,2026-10-31T14:04:16-07:00*% %TF.ProjectId,snips_controller,736e6970-735f-4636-9f6e-74726f6c6c65,rev?*% %TF.SameCoordinates,Original*% %TF.FileFunction,Component,L1,Top*% %TF.FilePolarity,Positive*% %FSLAX46Y46*% G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)* -G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-30 18:10:03* +G04 Created by KiCad (PCBNEW 10.0.5) date 2026-10-31 14:04:16* %MOMM*% %LPD*% G01* @@ -28,25 +28,24 @@ G04 APERTURE LIST* %TD*% G04 APERTURE END LIST* D10* -%TO.C,C_SYS_1*% -%TO.CFtp,C_0805_2012Metric*% -%TO.CVal,10µF*% -%TO.CLbN,Capacitor_SMD*% +%TO.C,C_3V3_3*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,39pF*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X135700000Y-120315000D03* +%TO.CRot,90*% +X140600000Y-103550000D03* D11* -X137395000Y-119340000D02* -X137395000Y-121290000D01* -X134005000Y-121290000D01* -X134005000Y-119340000D01* -X137395000Y-119340000D01* +X141055000Y-102645000D02* +X141055000Y-104455000D01* +X140145000Y-104455000D01* +X140145000Y-102645000D01* +X141055000Y-102645000D01* D12* -%TO.P,C_SYS_1,1*% -X134750000Y-120315000D03* +%TO.P,C_3V3_3,1*% +X140600000Y-104030000D03* D13* -%TO.P,C_SYS_1,2*% -X136650000Y-120315000D03* +%TO.P,C_3V3_3,2*% +X140600000Y-103070000D03* %TD*% D10* %TO.C,SW_MACRO4*% @@ -71,88 +70,107 @@ X123825000Y-103600000D03* X127975000Y-103600000D03* %TD*% D10* -%TO.C,C_VIN_2*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% -%TO.CLbN,Capacitor_SMD*% +%TO.C,C_OLED_1*% +%TO.CFtp,C_0603_1608Metric*% +%TO.CVal,1µF*% %TO.CMnt,SMD*% -%TO.CRot,90*% -X126750000Y-118795000D03* +%TO.CRot,180*% +X123400000Y-105100000D03* D11* -X127205000Y-117890000D02* -X127205000Y-119700000D01* -X126295000Y-119700000D01* -X126295000Y-117890000D01* -X127205000Y-117890000D01* +X124875000Y-104375000D02* +X124875000Y-105825000D01* +X121925000Y-105825000D01* +X121925000Y-104375000D01* +X124875000Y-104375000D01* D12* -%TO.P,C_VIN_2,1*% -X126750000Y-119275000D03* +%TO.P,C_OLED_1,1*% +X124175000Y-105100000D03* D13* -%TO.P,C_VIN_2,2*% -X126750000Y-118315000D03* +%TO.P,C_OLED_1,2*% +X122625000Y-105100000D03* %TD*% D10* -%TO.C,C_VIN_1*% -%TO.CFtp,C_0805_2012Metric*% -%TO.CVal,10µF*% -%TO.CLbN,Capacitor_SMD*% +%TO.C,R_EN_PU1*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,10kΩ*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X123800000Y-119315000D03* +%TO.CRot,0*% +X146000000Y-118600000D03* D11* -X125495000Y-118340000D02* -X125495000Y-120290000D01* -X122105000Y-120290000D01* -X122105000Y-118340000D01* -X125495000Y-118340000D01* +X146925000Y-118135000D02* +X146925000Y-119065000D01* +X145075000Y-119065000D01* +X145075000Y-118135000D01* +X146925000Y-118135000D01* D12* -%TO.P,C_VIN_1,1*% -X124750000Y-119315000D03* +%TO.P,R_EN_PU1,1*% +X145490000Y-118600000D03* D13* -%TO.P,C_VIN_1,2*% -X122850000Y-119315000D03* +%TO.P,R_EN_PU1,2*% +X146510000Y-118600000D03* %TD*% D10* -%TO.C,C_BUCK_OUT1*% -%TO.CFtp,C_0805_2012Metric*% -%TO.CVal,10µF*% +%TO.C,C_RGB1*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% %TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% %TO.CRot,90*% -X131475000Y-109800000D03* +X125800000Y-124600000D03* D11* -X132450000Y-108105000D02* -X132450000Y-111495000D01* -X130500000Y-111495000D01* -X130500000Y-108105000D01* -X132450000Y-108105000D01* +X126255000Y-123695000D02* +X126255000Y-125505000D01* +X125345000Y-125505000D01* +X125345000Y-123695000D01* +X126255000Y-123695000D01* D12* -%TO.P,C_BUCK_OUT1,1*% -X131475000Y-110750000D03* +%TO.P,C_RGB1,1*% +X125800000Y-125080000D03* D13* -%TO.P,C_BUCK_OUT1,2*% -X131475000Y-108850000D03* +%TO.P,C_RGB1,2*% +X125800000Y-124120000D03* %TD*% D10* -%TO.C,C_RGB1*% +%TO.C,SW_BOOT1*% +%TO.CFtp,SW_Alps_SKRP*% +%TO.CVal,SKRPABE010*% +%TO.CMnt,SMD*% +%TO.CRot,90*% +X147150000Y-114500000D03* +D11* +X148995000Y-111655000D02* +X148995000Y-117345000D01* +X145305000Y-117345000D01* +X145305000Y-111655000D01* +X148995000Y-111655000D01* +D12* +%TO.P,SW_BOOT1,1*% +X146075000Y-116575000D03* +X146075000Y-112425000D03* +D13* +%TO.P,SW_BOOT1,2*% +X148225000Y-116575000D03* +X148225000Y-112425000D03* +%TD*% +D10* +%TO.C,C_TRIG1*% %TO.CFtp,C_0402_1005Metric*% %TO.CVal,100nF*% -%TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X127750000Y-123750000D03* +%TO.CRot,90*% +X131600000Y-103350000D03* D11* -X128655000Y-123295000D02* -X128655000Y-124205000D01* -X126845000Y-124205000D01* -X126845000Y-123295000D01* -X128655000Y-123295000D01* +X132055000Y-102445000D02* +X132055000Y-104255000D01* +X131145000Y-104255000D01* +X131145000Y-102445000D01* +X132055000Y-102445000D01* D12* -%TO.P,C_RGB1,1*% -X127270000Y-123750000D03* +%TO.P,C_TRIG1,1*% +X131600000Y-103830000D03* D13* -%TO.P,C_RGB1,2*% -X128230000Y-123750000D03* +%TO.P,C_TRIG1,2*% +X131600000Y-102870000D03* %TD*% D10* %TO.C,FID1*% @@ -195,46 +213,44 @@ X132925000Y-96400000D03* X137075000Y-96400000D03* %TD*% D10* -%TO.C,C_BUCK_IN1*% -%TO.CFtp,C_0805_2012Metric*% -%TO.CVal,10µF*% -%TO.CLbN,Capacitor_SMD*% +%TO.C,C_EN1*% +%TO.CFtp,C_0603_1608Metric*% +%TO.CVal,1µF*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X139950000Y-114300000D03* +%TO.CRot,0*% +X146000000Y-120300000D03* D11* -X141645000Y-113325000D02* -X141645000Y-115275000D01* -X138255000Y-115275000D01* -X138255000Y-113325000D01* -X141645000Y-113325000D01* +X147475000Y-119575000D02* +X147475000Y-121025000D01* +X144525000Y-121025000D01* +X144525000Y-119575000D01* +X147475000Y-119575000D01* D12* -%TO.P,C_BUCK_IN1,1*% -X140900000Y-114300000D03* +%TO.P,C_EN1,1*% +X145225000Y-120300000D03* D13* -%TO.P,C_BUCK_IN1,2*% -X139000000Y-114300000D03* +%TO.P,C_EN1,2*% +X146775000Y-120300000D03* %TD*% D10* -%TO.C,C_SYS_2*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% -%TO.CLbN,Capacitor_SMD*% +%TO.C,R_USB_DM1*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,27Ω*% %TO.CMnt,SMD*% %TO.CRot,90*% -X132250000Y-119835000D03* +X128020000Y-114460000D03* D11* -X132705000Y-118930000D02* -X132705000Y-120740000D01* -X131795000Y-120740000D01* -X131795000Y-118930000D01* -X132705000Y-118930000D01* +X128485000Y-113535000D02* +X128485000Y-115385000D01* +X127555000Y-115385000D01* +X127555000Y-113535000D01* +X128485000Y-113535000D01* D12* -%TO.P,C_SYS_2,1*% -X132250000Y-120315000D03* +%TO.P,R_USB_DM1,1*% +X128020000Y-114970000D03* D13* -%TO.P,C_SYS_2,2*% -X132250000Y-119355000D03* +%TO.P,R_USB_DM1,2*% +X128020000Y-113950000D03* %TD*% D10* %TO.C,SW_THR_UP1*% @@ -355,129 +371,44 @@ X127850000Y-128650000D03* X129650000Y-128650000D03* %TD*% D10* -%TO.C,C_BAT1*% -%TO.CFtp,C_0805_2012Metric*% -%TO.CVal,10µF*% -%TO.CLbN,Capacitor_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,0*% -X134200000Y-116815000D03* -D11* -X135895000Y-115840000D02* -X135895000Y-117790000D01* -X132505000Y-117790000D01* -X132505000Y-115840000D01* -X135895000Y-115840000D01* -D12* -%TO.P,C_BAT1,1*% -X133250000Y-116815000D03* -D13* -%TO.P,C_BAT1,2*% -X135150000Y-116815000D03* -%TD*% -D10* -%TO.C,U_CHG1*% -%TO.CFtp,IC_BQ25185DLHR*% -%TO.CVal,BQ25185DLHR*% -%TO.CLbN,BQ25185DLHR*% -%TO.CMnt,SMD*% -%TO.CRot,180*% -X129750000Y-118315000D03* -D11* -X131295000Y-117070000D02* -X131295000Y-119560000D01* -X128205000Y-119560000D01* -X128205000Y-117070000D01* -X131295000Y-117070000D01* -D12* -%TO.P,U_CHG1,1,SYS_1*% -X130800000Y-119115000D03* -D13* -%TO.P,U_CHG1,2,BAT_2*% -X130800000Y-118715000D03* -%TO.P,U_CHG1,3,STAT2_3*% -X130800000Y-118315000D03* -%TO.P,U_CHG1,4,~{CE}_4*% -X130800000Y-117915000D03* -%TO.P,U_CHG1,5,GND_5*% -X130800000Y-117515000D03* -%TO.P,U_CHG1,6,TS/MR_6*% -X128700000Y-117515000D03* -%TO.P,U_CHG1,7,ILIM/VSET_7*% -X128700000Y-117915000D03* -%TO.P,U_CHG1,8,ISET_8*% -X128700000Y-118315000D03* -%TO.P,U_CHG1,9,STAT1_9*% -X128700000Y-118715000D03* -%TO.P,U_CHG1,10,IN_10*% -X128700000Y-119115000D03* -%TO.P,U_CHG1,11,THERMAL_PAD_11*% -X129750000Y-118315000D03* -%TO.P,U_CHG1,12*% -X129750000Y-118815000D03* -%TO.P,U_CHG1,13*% -X129750000Y-117815000D03* -%TD*% -D10* %TO.C,U_OLED1*% %TO.CFtp,JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal*% %TO.CVal,Qwiic connector*% %TO.CLbN,Connector_JST*% %TO.CMnt,SMD*% %TO.CRot,0*% -X124400000Y-108125000D03* -D11* -X126695000Y-104850000D02* -X126695000Y-105950000D01* -X127895000Y-105950000D01* -X127895000Y-108600000D01* -X128295000Y-108600000D01* -X128295000Y-111400000D01* -X126095000Y-111400000D01* -X126095000Y-111200000D01* -X122705000Y-111200000D01* -X122705000Y-111400000D01* -X120505000Y-111400000D01* -X120505000Y-108600000D01* -X120905000Y-108600000D01* -X120905000Y-105950000D01* -X122105000Y-105950000D01* -X122105000Y-104850000D01* -X126695000Y-104850000D01* +X124400000Y-110125000D03* +D11* +X126695000Y-106850000D02* +X126695000Y-107950000D01* +X127895000Y-107950000D01* +X127895000Y-110600000D01* +X128295000Y-110600000D01* +X128295000Y-113400000D01* +X126095000Y-113400000D01* +X126095000Y-113200000D01* +X122705000Y-113200000D01* +X122705000Y-113400000D01* +X120505000Y-113400000D01* +X120505000Y-110600000D01* +X120905000Y-110600000D01* +X120905000Y-107950000D01* +X122105000Y-107950000D01* +X122105000Y-106850000D01* +X126695000Y-106850000D01* D12* %TO.P,U_OLED1,1,GND_1*% -X122900000Y-106125000D03* +X122900000Y-108125000D03* D13* %TO.P,U_OLED1,2,VCC_2*% -X123900000Y-106125000D03* +X123900000Y-108125000D03* %TO.P,U_OLED1,3,SDA_3*% -X124900000Y-106125000D03* +X124900000Y-108125000D03* %TO.P,U_OLED1,4,SCL_4*% -X125900000Y-106125000D03* +X125900000Y-108125000D03* %TO.P,U_OLED1,MP*% -X121600000Y-110000000D03* -X127200000Y-110000000D03* -%TD*% -D10* -%TO.C,R_STAT2*% -%TO.CFtp,R_0402_1005Metric*% -%TO.CVal,10kΩ*% -%TO.CLbN,Resistor_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,0*% -X134350000Y-114515000D03* -D11* -X135275000Y-114050000D02* -X135275000Y-114980000D01* -X133425000Y-114980000D01* -X133425000Y-114050000D01* -X135275000Y-114050000D01* -D12* -%TO.P,R_STAT2,1*% -X133840000Y-114515000D03* -D13* -%TO.P,R_STAT2,2*% -X134860000Y-114515000D03* +X121600000Y-112000000D03* +X127200000Y-112000000D03* %TD*% D10* %TO.C,FID2*% @@ -498,25 +429,179 @@ D13* X143750000Y-61750000D03* %TD*% D10* -%TO.C,R_FB2*% -%TO.CFtp,R_0402_1005Metric*% -%TO.CVal,56.2kΩ*% -%TO.CLbN,Resistor_SMD*% +%TO.C,C_OLED_2*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% +%TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X133740000Y-106725000D03* +%TO.CRot,180*% +X123400000Y-106300000D03* D11* -X134665000Y-106260000D02* -X134665000Y-107190000D01* -X132815000Y-107190000D01* -X132815000Y-106260000D01* -X134665000Y-106260000D01* +X124305000Y-105845000D02* +X124305000Y-106755000D01* +X122495000Y-106755000D01* +X122495000Y-105845000D01* +X124305000Y-105845000D01* D12* -%TO.P,R_FB2,1*% -X133230000Y-106725000D03* +%TO.P,C_OLED_2,1*% +X123880000Y-106300000D03* D13* -%TO.P,R_FB2,2*% -X134250000Y-106725000D03* +%TO.P,C_OLED_2,2*% +X122920000Y-106300000D03* +%TD*% +D10* +%TO.C,U_MCU1*% +%TO.CFtp,ESP32-S3-MINI-1U*% +%TO.CVal,ESP32-S3-MINI-1U-N8*% +%TO.CMnt,SMD*% +%TO.CRot,-90*% +X136500000Y-112500000D03* +D11* +X144495000Y-104505000D02* +X144495000Y-120495000D01* +X128505000Y-120495000D01* +X128505000Y-104505000D01* +X144495000Y-104505000D01* +D12* +%TO.P,U_MCU1,1*% +X142450000Y-105500000D03* +D13* +%TO.P,U_MCU1,2*% +X141600000Y-105500000D03* +%TO.P,U_MCU1,3*% +X140750000Y-105500000D03* +%TO.P,U_MCU1,4*% +X139900000Y-105500000D03* +%TO.P,U_MCU1,5*% +X139050000Y-105500000D03* +%TO.P,U_MCU1,6*% +X138200000Y-105500000D03* +%TO.P,U_MCU1,7*% +X137350000Y-105500000D03* +%TO.P,U_MCU1,8*% +X136500000Y-105500000D03* +%TO.P,U_MCU1,9*% +X135650000Y-105500000D03* +%TO.P,U_MCU1,10*% +X134800000Y-105500000D03* +%TO.P,U_MCU1,11*% +X133950000Y-105500000D03* +%TO.P,U_MCU1,12*% +X133100000Y-105500000D03* +%TO.P,U_MCU1,13*% +X132250000Y-105500000D03* +%TO.P,U_MCU1,14*% +X131400000Y-105500000D03* +%TO.P,U_MCU1,15*% +X130550000Y-105500000D03* +%TO.P,U_MCU1,16*% +X129500000Y-106550000D03* +%TO.P,U_MCU1,17*% +X129500000Y-107400000D03* +%TO.P,U_MCU1,18*% +X129500000Y-108250000D03* +%TO.P,U_MCU1,19*% +X129500000Y-109100000D03* +%TO.P,U_MCU1,20*% +X129500000Y-109950000D03* +%TO.P,U_MCU1,21*% +X129500000Y-110800000D03* +%TO.P,U_MCU1,22*% +X129500000Y-111650000D03* +%TO.P,U_MCU1,23*% +X129500000Y-112500000D03* +%TO.P,U_MCU1,24*% +X129500000Y-113350000D03* +%TO.P,U_MCU1,25*% +X129500000Y-114200000D03* +%TO.P,U_MCU1,26*% +X129500000Y-115050000D03* +%TO.P,U_MCU1,27*% +X129500000Y-115900000D03* +%TO.P,U_MCU1,28*% +X129500000Y-116750000D03* +%TO.P,U_MCU1,29*% +X129500000Y-117600000D03* +%TO.P,U_MCU1,30*% +X129500000Y-118450000D03* +%TO.P,U_MCU1,31*% +X130550000Y-119500000D03* +%TO.P,U_MCU1,32*% +X131400000Y-119500000D03* +%TO.P,U_MCU1,33*% +X132250000Y-119500000D03* +%TO.P,U_MCU1,34*% +X133100000Y-119500000D03* +%TO.P,U_MCU1,35*% +X133950000Y-119500000D03* +%TO.P,U_MCU1,36*% +X134800000Y-119500000D03* +%TO.P,U_MCU1,37*% +X135650000Y-119500000D03* +%TO.P,U_MCU1,38*% +X136500000Y-119500000D03* +%TO.P,U_MCU1,39*% +X137350000Y-119500000D03* +%TO.P,U_MCU1,40*% +X138200000Y-119500000D03* +%TO.P,U_MCU1,41*% +X139050000Y-119500000D03* +%TO.P,U_MCU1,42*% +X139900000Y-119500000D03* +%TO.P,U_MCU1,43*% +X140750000Y-119500000D03* +%TO.P,U_MCU1,44*% +X141600000Y-119500000D03* +%TO.P,U_MCU1,45*% +X142450000Y-119500000D03* +%TO.P,U_MCU1,46*% +X143500000Y-118450000D03* +%TO.P,U_MCU1,47*% +X143500000Y-117600000D03* +%TO.P,U_MCU1,48*% +X143500000Y-116750000D03* +%TO.P,U_MCU1,49*% +X143500000Y-115900000D03* +%TO.P,U_MCU1,50*% +X143500000Y-115050000D03* +%TO.P,U_MCU1,51*% +X143500000Y-114200000D03* +%TO.P,U_MCU1,52*% +X143500000Y-113350000D03* +%TO.P,U_MCU1,53*% +X143500000Y-112500000D03* +%TO.P,U_MCU1,54*% +X143500000Y-111650000D03* +%TO.P,U_MCU1,55*% +X143500000Y-110800000D03* +%TO.P,U_MCU1,56*% +X143500000Y-109950000D03* +%TO.P,U_MCU1,57*% +X143500000Y-109100000D03* +%TO.P,U_MCU1,58*% +X143500000Y-108250000D03* +%TO.P,U_MCU1,59*% +X143500000Y-107400000D03* +%TO.P,U_MCU1,60*% +X143500000Y-106550000D03* +%TO.P,U_MCU1,61*% +X138150000Y-110850000D03* +X136500000Y-110850000D03* +X134850000Y-110850000D03* +X138150000Y-112500000D03* +X136500000Y-112500000D03* +X134850000Y-112500000D03* +X138150000Y-114150000D03* +X136500000Y-114150000D03* +X134850000Y-114150000D03* +%TO.P,U_MCU1,62*% +X143500000Y-105500000D03* +%TO.P,U_MCU1,63*% +X129500000Y-105500000D03* +%TO.P,U_MCU1,64*% +X129500000Y-119500000D03* +%TO.P,U_MCU1,65*% +X143500000Y-119500000D03* %TD*% D10* %TO.C,SW_VOL_DN1*% @@ -604,172 +689,129 @@ X141320000Y-124020000D03* X141320000Y-128200000D03* %TD*% D10* -%TO.C,R_VSET1*% -%TO.CFtp,R_0402_1005Metric*% -%TO.CVal,18kΩ*% -%TO.CLbN,Resistor_SMD*% +%TO.C,C_DBNC1*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% +%TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% %TO.CRot,180*% -X122260000Y-115500000D03* +X123600000Y-125200000D03* D11* -X123185000Y-115035000D02* -X123185000Y-115965000D01* -X121335000Y-115965000D01* -X121335000Y-115035000D01* -X123185000Y-115035000D01* +X124505000Y-124745000D02* +X124505000Y-125655000D01* +X122695000Y-125655000D01* +X122695000Y-124745000D01* +X124505000Y-124745000D01* D12* -%TO.P,R_VSET1,1*% -X122770000Y-115500000D03* +%TO.P,C_DBNC1,1*% +X124080000Y-125200000D03* D13* -%TO.P,R_VSET1,2*% -X121750000Y-115500000D03* +%TO.P,C_DBNC1,2*% +X123120000Y-125200000D03* %TD*% D10* -%TO.C,J_STICK1*% -%TO.CFtp,GuliKit_HallStick*% -%TO.CVal,GuliKit_Thumbstick*% -%TO.CLbN,SnipsControllers_Custom*% -%TO.CMnt,TH*% -%TO.CRot,0*% -X135000000Y-78500000D03* -D14* -X127400000Y-68745000D02* -X127400000Y-89875000D01* -X144755000Y-89875000D01* -X144755000Y-68745000D01* -X127400000Y-68745000D01* -D12* -%TO.P,J_STICK1,1,X_LO_1*% -X137500000Y-69770000D03* -D13* -%TO.P,J_STICK1,*% -X128675000Y-73500000D03* -X128675000Y-83500000D03* -X141325000Y-73500000D03* -X141325000Y-83500000D03* -%TO.P,J_STICK1,1',Y_LO_1'*% -X143730000Y-81000000D03* -%TO.P,J_STICK1,2,X_OUT_2*% -X135000000Y-69770000D03* -%TO.P,J_STICK1,2',Y_OUT_2'*% -X143730000Y-78500000D03* -%TO.P,J_STICK1,3,X_HI_3*% -X132500000Y-69770000D03* -%TO.P,J_STICK1,3',Y_HI_3'*% -X143730000Y-76000000D03* -%TO.P,J_STICK1,a,SW_A_a*% -X131750000Y-84250000D03* -%TO.P,J_STICK1,b*% -X138250000Y-84250000D03* -%TO.P,J_STICK1,c,SW_C_c*% -X131750000Y-88750000D03* -%TO.P,J_STICK1,d*% -X138250000Y-88750000D03* -%TD*% -D10* -%TO.C,R_STAT1*% +%TO.C,R_RGB1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,10kΩ*% +%TO.CVal,470Ω*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X125160000Y-117315000D03* +%TO.CRot,90*% +X127900000Y-122990000D03* D11* -X126085000Y-116850000D02* -X126085000Y-117780000D01* -X124235000Y-117780000D01* -X124235000Y-116850000D01* -X126085000Y-116850000D01* +X128365000Y-122065000D02* +X128365000Y-123915000D01* +X127435000Y-123915000D01* +X127435000Y-122065000D01* +X128365000Y-122065000D01* D12* -%TO.P,R_STAT1,1*% -X125670000Y-117315000D03* +%TO.P,R_RGB1,1*% +X127900000Y-123500000D03* D13* -%TO.P,R_STAT1,2*% -X124650000Y-117315000D03* +%TO.P,R_RGB1,2*% +X127900000Y-122480000D03* %TD*% D10* -%TO.C,R_ISET1*% -%TO.CFtp,R_0402_1005Metric*% -%TO.CVal,604Ω*% -%TO.CLbN,Resistor_SMD*% +%TO.C,C_3V3_2*% +%TO.CFtp,C_0402_1005Metric*% +%TO.CVal,100nF*% +%TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X122280000Y-116515000D03* +%TO.CRot,90*% +X140600000Y-101600000D03* D11* -X123205000Y-116050000D02* -X123205000Y-116980000D01* -X121355000Y-116980000D01* -X121355000Y-116050000D01* -X123205000Y-116050000D01* +X141055000Y-100695000D02* +X141055000Y-102505000D01* +X140145000Y-102505000D01* +X140145000Y-100695000D01* +X141055000Y-100695000D01* D12* -%TO.P,R_ISET1,1*% -X122790000Y-116515000D03* +%TO.P,C_3V3_2,1*% +X140600000Y-102080000D03* D13* -%TO.P,R_ISET1,2*% -X121770000Y-116515000D03* +%TO.P,C_3V3_2,2*% +X140600000Y-101120000D03* %TD*% D10* -%TO.C,C_DBNC1*% -%TO.CFtp,C_0402_1005Metric*% -%TO.CVal,100nF*% +%TO.C,C_3V3_1*% +%TO.CFtp,C_0603_1608Metric*% +%TO.CVal,10µF*% %TO.CLbN,Capacitor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X123600000Y-125200000D03* +%TO.CRot,90*% +X145300000Y-106000000D03* D11* -X124505000Y-124745000D02* -X124505000Y-125655000D01* -X122695000Y-125655000D01* -X122695000Y-124745000D01* -X124505000Y-124745000D01* +X146025000Y-104525000D02* +X146025000Y-107475000D01* +X144575000Y-107475000D01* +X144575000Y-104525000D01* +X146025000Y-104525000D01* D12* -%TO.P,C_DBNC1,1*% -X124080000Y-125200000D03* +%TO.P,C_3V3_1,1*% +X145300000Y-106775000D03* D13* -%TO.P,C_DBNC1,2*% -X123120000Y-125200000D03* +%TO.P,C_3V3_1,2*% +X145300000Y-105225000D03* %TD*% D10* -%TO.C,R_RGB1*% +%TO.C,R_VSYS1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,470Ω*% +%TO.CVal,200kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,0*% -X127750000Y-122600000D03* +%TO.CRot,-90*% +X129800000Y-101410000D03* D11* -X128675000Y-122135000D02* -X128675000Y-123065000D01* -X126825000Y-123065000D01* -X126825000Y-122135000D01* -X128675000Y-122135000D01* +X130265000Y-100485000D02* +X130265000Y-102335000D01* +X129335000Y-102335000D01* +X129335000Y-100485000D01* +X130265000Y-100485000D01* D12* -%TO.P,R_RGB1,1*% -X127240000Y-122600000D03* +%TO.P,R_VSYS1,1*% +X129800000Y-100900000D03* D13* -%TO.P,R_RGB1,2*% -X128260000Y-122600000D03* +%TO.P,R_VSYS1,2*% +X129800000Y-101920000D03* %TD*% D10* -%TO.C,R_FB1*% +%TO.C,R_I2C_SDA1*% %TO.CFtp,R_0402_1005Metric*% -%TO.CVal,255kΩ*% -%TO.CLbN,Resistor_SMD*% +%TO.CVal,4.7kΩ*% %TO.CMnt,SMD*% %TO.CRot,-90*% -X131975000Y-106550000D03* +X125500000Y-105790000D03* D11* -X132440000Y-105625000D02* -X132440000Y-107475000D01* -X131510000Y-107475000D01* -X131510000Y-105625000D01* -X132440000Y-105625000D01* +X125965000Y-104865000D02* +X125965000Y-106715000D01* +X125035000Y-106715000D01* +X125035000Y-104865000D01* +X125965000Y-104865000D01* D12* -%TO.P,R_FB1,1*% -X131975000Y-106040000D03* +%TO.P,R_I2C_SDA1,1*% +X125500000Y-105280000D03* D13* -%TO.P,R_FB1,2*% -X131975000Y-107060000D03* +%TO.P,R_I2C_SDA1,2*% +X125500000Y-106300000D03* %TD*% D10* %TO.C,SW_THR_DN1*% @@ -800,6 +842,26 @@ X120750000Y-81650000D03* X120750000Y-85350000D03* %TD*% D10* +%TO.C,R_I2C_SCL1*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,4.7kΩ*% +%TO.CMnt,SMD*% +%TO.CRot,-90*% +X127200000Y-106900000D03* +D11* +X127665000Y-105975000D02* +X127665000Y-107825000D01* +X126735000Y-107825000D01* +X126735000Y-105975000D01* +X127665000Y-105975000D01* +D12* +%TO.P,R_I2C_SCL1,1*% +X127200000Y-106390000D03* +D13* +%TO.P,R_I2C_SCL1,2*% +X127200000Y-107410000D03* +%TD*% +D10* %TO.C,SW_VOL_UP1*% %TO.CFtp,SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010*% %TO.CVal,SKRTLAE010*% @@ -828,66 +890,6 @@ X149250000Y-75350000D03* X149250000Y-71650000D03* %TD*% D10* -%TO.C,U_BUCK1*% -%TO.CFtp,SOT-23-5*% -%TO.CVal,TLV62569DBVR*% -%TO.CLbN,Package_TO_SOT_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,-90*% -X140925000Y-110937500D03* -D11* -X142420000Y-108892500D02* -X142420000Y-109892500D01* -X142620000Y-109892500D01* -X142620000Y-111982500D01* -X142420000Y-111982500D01* -X142420000Y-112982500D01* -X141320000Y-112982500D01* -X141320000Y-111982500D01* -X140530000Y-111982500D01* -X140530000Y-112982500D01* -X139430000Y-112982500D01* -X139430000Y-111982500D01* -X139230000Y-111982500D01* -X139230000Y-109892500D01* -X139430000Y-109892500D01* -X139430000Y-108892500D01* -X142420000Y-108892500D01* -D12* -%TO.P,U_BUCK1,1,EN_1*% -X141875000Y-109800000D03* -D13* -%TO.P,U_BUCK1,2,GND_2*% -X140925000Y-109800000D03* -%TO.P,U_BUCK1,3,SW_3*% -X139975000Y-109800000D03* -%TO.P,U_BUCK1,4,VIN_4*% -X139975000Y-112075000D03* -%TO.P,U_BUCK1,5,FB_5*% -X141875000Y-112075000D03* -%TD*% -D10* -%TO.C,L_BUCK1*% -%TO.CFtp,L_Bourns-SRN4018*% -%TO.CVal,2.2µH*% -%TO.CLbN,Inductor_SMD*% -%TO.CMnt,SMD*% -%TO.CRot,180*% -X135975000Y-109800000D03* -D11* -X138500000Y-107555000D02* -X138500000Y-112045000D01* -X133450000Y-112045000D01* -X133450000Y-107555000D01* -X138500000Y-107555000D01* -D12* -%TO.P,L_BUCK1,1,1_1*% -X137500000Y-109800000D03* -D13* -%TO.P,L_BUCK1,2,2_2*% -X134450000Y-109800000D03* -%TD*% -D10* %TO.C,FID3*% %TO.CFtp,Fiducial_1mm_Mask2mm*% %TO.CVal,Fiducial_1mm_Mask2mm*% @@ -906,6 +908,27 @@ D13* X148500000Y-121000000D03* %TD*% D10* +%TO.C,R_VSYS2*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,100kΩ*% +%TO.CLbN,Resistor_SMD*% +%TO.CMnt,SMD*% +%TO.CRot,-90*% +X130000000Y-103400000D03* +D11* +X130465000Y-102475000D02* +X130465000Y-104325000D01* +X129535000Y-104325000D01* +X129535000Y-102475000D01* +X130465000Y-102475000D01* +D12* +%TO.P,R_VSYS2,1*% +X130000000Y-102890000D03* +D13* +%TO.P,R_VSYS2,2*% +X130000000Y-103910000D03* +%TD*% +D10* %TO.C,SW_PWR1*% %TO.CFtp,SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010*% %TO.CVal,SKRTLAE010*% @@ -934,6 +957,26 @@ X121150000Y-128950000D03* X124850000Y-128950000D03* %TD*% D10* +%TO.C,R_USB_DP1*% +%TO.CFtp,R_0402_1005Metric*% +%TO.CVal,27Ω*% +%TO.CMnt,SMD*% +%TO.CRot,90*% +X128020000Y-116400000D03* +D11* +X128485000Y-115475000D02* +X128485000Y-117325000D01* +X127555000Y-117325000D01* +X127555000Y-115475000D01* +X128485000Y-115475000D01* +D12* +%TO.P,R_USB_DP1,1*% +X128020000Y-116910000D03* +D13* +%TO.P,R_USB_DP1,2*% +X128020000Y-115890000D03* +%TD*% +D10* %TO.C,SW_MACRO5*% %TO.CFtp,SW_Alps_SKRP*% %TO.CVal,SKRPABE010*% @@ -956,24 +999,24 @@ X132925000Y-103600000D03* X137075000Y-103600000D03* %TD*% D10* -%TO.C,R_TS1*% +%TO.C,R_BOOT_PU1*% %TO.CFtp,R_0402_1005Metric*% %TO.CVal,10kΩ*% %TO.CLbN,Resistor_SMD*% %TO.CMnt,SMD*% -%TO.CRot,180*% -X122260000Y-114500000D03* +%TO.CRot,90*% +X145800000Y-109410000D03* D11* -X123185000Y-114035000D02* -X123185000Y-114965000D01* -X121335000Y-114965000D01* -X121335000Y-114035000D01* -X123185000Y-114035000D01* +X146265000Y-108485000D02* +X146265000Y-110335000D01* +X145335000Y-110335000D01* +X145335000Y-108485000D01* +X146265000Y-108485000D01* D12* -%TO.P,R_TS1,1*% -X122770000Y-114500000D03* +%TO.P,R_BOOT_PU1,1*% +X145800000Y-109920000D03* D13* -%TO.P,R_TS1,2*% -X121750000Y-114500000D03* +%TO.P,R_BOOT_PU1,2*% +X145800000Y-108900000D03* %TD*% M02* diff --git a/PCB/v2.x/snips_controller.kicad_pcb b/PCB/v2.x/snips_controller.kicad_pcb index 56ecd03..1979b39 100644 --- a/PCB/v2.x/snips_controller.kicad_pcb +++ b/PCB/v2.x/snips_controller.kicad_pcb @@ -154,17 +154,17 @@ (outputdirectory "production/gerbers/") ) ) - (footprint "Capacitor_SMD:C_0805_2012Metric" + (footprint "C_0402_1005Metric" (layer "F.Cu") - (uuid "0390cbd8-aad5-4513-8815-b8e8b89441b2") - (at 135.7 120.315) - (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (uuid "09e18595-d8fc-4102-bdaa-35c18c41f35e") + (at 140.6 103.55 90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") - (property "Reference" "C_SYS_1" - (at 0 -1.68 180) + (property "Reference" "C_3V3_3" + (at 0 -1.16 90) (layer "F.SilkS") (hide yes) - (uuid "462f5cf9-ee6a-49e3-9d91-19a8f95e4c99") + (uuid "321e2628-7846-437a-b7b6-54ebe1dc7fad") (effects (font (size 1 1) @@ -172,10 +172,10 @@ ) ) ) - (property "Value" "10µF" - (at 0 1.68 180) + (property "Value" "39pF" + (at 0 1.16 90) (layer "F.Fab") - (uuid "f6dd34e2-1a7e-4242-a613-075d419820ea") + (uuid "e987d91b-ad53-48cd-8ad6-26d0db6c10fd") (effects (font (size 1 1) @@ -184,33 +184,32 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "a54cd415-70da-4145-b792-a42b1cfdb01d") + (uuid "f6afab23-9fb4-4be2-b02d-d2c424a9a49f") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 180) + (property "Description" "" + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "476d8b11-b125-486f-abc1-e1acb2df385e") + (uuid "a7e2e4c1-1a0e-4f50-b102-93b514350d8e") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 90) + (layer "F.SilkS") (hide yes) - (uuid "f2cd291d-80fe-4e7c-bcd6-0a18265538aa") + (uuid "412b292a-6eee-41f5-b6d5-5c80a44a64a2") (effects (font (size 1 1) @@ -218,141 +217,140 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") + (property "MF" "Yageo" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "962c8b77-9f33-489f-ba7c-17cda90821a8") + (uuid "1feec6d0-e66a-4c86-af5c-a99f03dfda23") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "LCSC" "C15850" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "CC0402JRNPO9BN390" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "dfc0e204-27b5-4747-b51b-e7acd18a4832") + (uuid "6403d7c6-1dd4-4648-a310-e2c5dc928c61") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Stackup Path" "C_SYS_1" - (at 0 -2 180) + (property "LCSC" "C106223" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "30080745-879b-4733-a974-11c9086c8a99") + (uuid "56e56439-b2ef-4a6d-b8ad-4a30d441eb2a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:36" - (at 0 -2 180) + (property "Stackup Path" "C_3V3_3" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "5ec1c961-646b-438f-b18b-04ad86600ba0") + (uuid "85cf149b-547a-4dff-a1a0-98e5ab6260da") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/2d079967-45b0-53cc-b8e7-a89bd1adba7c") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:23" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "8d7b7059-75f2-43da-88b1-47990fb388e4") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/fd89b7d8-b5eb-5153-97f5-9cc4658cf3f1") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.261252 -0.735) - (end 0.261252 -0.735) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "b2ebadc8-9101-4e30-b021-c7888640bc5c") + (uuid "b74b4981-5b1c-47e5-a2ab-6ae1e654ca81") ) (fp_line - (start -0.261252 0.735) - (end 0.261252 0.735) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "fd348c30-ac96-4b88-8e39-bcd0c5322995") + (uuid "0a70c949-633a-43fd-b8ec-69cdf1f3b537") ) (fp_rect - (start -1.7 -0.98) - (end 1.7 0.98) + (start -0.91 -0.46) + (end 0.91 0.46) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "cdd72dd5-f290-4529-99b8-cc9d439360f9") + (uuid "9d68ada6-99eb-4141-aa17-f733b1af6fbb") ) (fp_rect - (start -1 -0.625) - (end 1 0.625) + (start -0.5 -0.25) + (end 0.5 0.25) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "c79fe089-a387-47f3-ac61-f5b8ad8d6266") + (uuid "340a4947-79f5-49a5-985c-436ce074b671") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 90) (layer "F.Fab") - (uuid "7d6fb0c1-d49a-46c1-a6f3-5c455d3cdd7d") + (uuid "1183a86c-da11-4cc8-8180-f041c0929117") (effects (font - (size 0.5 0.5) - (thickness 0.08) + (size 0.25 0.25) + (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.95 0) - (size 1 1.45) + (at -0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "VSYS") - (pintype "passive") - (uuid "6889a83d-65de-48a9-8120-aa0cfb12d1a5") + (net "3V3") + (uuid "c1912cca-efeb-4600-892b-007a08f55c78") ) (pad "2" smd roundrect - (at 0.95 0) - (size 1 1.45) + (at 0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "c03d2c4a-2e1f-468b-a9cd-ceeeafa06362") + (uuid "b62bb223-bb01-43d5-bf33-322f85ff7395") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -467,7 +465,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:78" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:81" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -736,17 +734,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0402_1005Metric" + (footprint "C_0603_1608Metric" (layer "F.Cu") - (uuid "1a9ba0b3-7962-454b-a452-bbae057a5f76") - (at 126.75 118.795 90) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (uuid "13d92b51-f732-426d-ad79-903d065110d0") + (at 123.4 105.1 180) + (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") - (property "Reference" "C_VIN_2" - (at 0 -1.16 90) + (property "Reference" "C_OLED_1" + (at 0 -1.43 0) (layer "F.SilkS") (hide yes) - (uuid "3f4924b1-fa87-46de-8511-8d14abd9ffe4") + (uuid "abb02ee5-fdaf-4c79-b084-58baecf69712") (effects (font (size 1 1) @@ -754,10 +752,10 @@ ) ) ) - (property "Value" "100nF" - (at 0 1.16 90) + (property "Value" "1µF" + (at 0 1.43 0) (layer "F.Fab") - (uuid "5fddc59e-0e12-4b3d-8324-a8fe05ad54b4") + (uuid "df2b867a-2937-413c-9eaf-f15fcc8ab729") (effects (font (size 1 1) @@ -766,33 +764,32 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "f05d216e-7025-431c-82c5-a9678d4b3f46") + (uuid "77565b82-0988-4b33-ba64-2b0385229649") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 90) + (property "Description" "" + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "85bef30a-7603-4eff-a620-28c31d8c4545") + (uuid "be8ae1f0-8f7f-4002-9ccd-231556a23e8b") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 0) + (layer "F.SilkS") (hide yes) - (uuid "e0c9722d-1c27-4b1e-9dc7-ab9465159d2c") + (uuid "364e5dfc-2dcf-4328-811b-5a6a773167fd") (effects (font (size 1 1) @@ -800,37 +797,37 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "MF" "Samsung Electro-Mechanics" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "329de3dc-4ca1-4724-a045-08e8a90e9a62") + (uuid "34d5dd0c-6e43-4ca6-9a84-ae2e84f4b00d") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (property "LCSC" "C1525" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "CL10A105KB8NNNC" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "7addb406-e375-47a7-8a4e-2e6906c11d7b") + (uuid "30246e0a-d7e9-4184-9e02-8ab3ca676e3b") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (property "Stackup Path" "C_VIN_2" - (at 2 0 180) + (property "LCSC" "C15849" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "5c5bd414-4686-4652-9b01-28f7213a7ae1") + (uuid "0c475505-db17-42f0-ab73-e2342eceebc3") (effects (font (size 1.27 1.27) @@ -839,11 +836,11 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:39" - (at 2 0 180) + (property "Stackup Path" "C_OLED_1" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "9833576d-3be8-43a7-9af4-8b2b86fac03f") + (uuid "0501c0f8-1495-484c-b599-9110ee6caa1e") (effects (font (size 1.27 1.27) @@ -852,89 +849,93 @@ (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/767a3c48-9a20-55ce-920a-cf805399b457") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:34" + (at 0 2 0) + (layer "F.SilkS") + (hide yes) + (uuid "ccaff32f-e0fd-4c53-bc18-41b8246fe057") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + (justify mirror) ) ) + (path "/722d9e65-c2cb-5466-b845-abde86ab0018") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.14058 0.51) + (end 0.14058 0.51) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "369f1213-037b-40bd-a3de-703e6bc3505d") + (uuid "fed99db1-b465-4259-bb29-5465d35775d7") ) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.14058 -0.51) + (end 0.14058 -0.51) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "033aac32-1f1a-4343-9486-6e046ecaa56a") + (uuid "68091d5d-ec6a-4231-9ece-49be3d1b812f") ) (fp_rect - (start -0.91 -0.46) - (end 0.91 0.46) + (start -1.48 -0.73) + (end 1.48 0.73) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "05b89e4d-c3ea-4af0-9486-2409802ecb80") + (uuid "eb0146bb-2154-4347-a987-b18accfd0220") ) (fp_rect - (start -0.5 -0.25) - (end 0.5 0.25) + (start -0.8 -0.4) + (end 0.8 0.4) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "d39b05d0-41a9-4e61-87ed-388c7c6041fa") + (uuid "dbbef132-57de-4fbe-a38a-741c29076ce1") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 0) (layer "F.Fab") - (uuid "5cd8b027-3c74-4b8c-a1f5-c359ba9aae2c") + (uuid "a1120d2c-b5d6-4a71-9fa7-d9e14d47c122") (effects (font - (size 0.25 0.25) - (thickness 0.04) + (size 0.4 0.4) + (thickness 0.06) ) ) ) (pad "1" smd roundrect - (at -0.48 0 90) - (size 0.56 0.62) + (at -0.775 0 180) + (size 0.9 0.95) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "VBUS") - (pintype "passive") - (uuid "6bf76f7e-018c-49c5-ad23-be362d088e4e") + (net "3V3") + (uuid "7139f714-8c4a-475b-866b-b092fb48473f") ) (pad "2" smd roundrect - (at 0.48 0 90) - (size 0.56 0.62) + (at 0.775 0 180) + (size 0.9 0.95) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "281631d6-449a-4a07-a14f-bc0bbeff768d") + (uuid "17ed6ea4-3ee6-40a3-a2b3-81d30f826739") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" (offset (xyz 0 0 0) ) @@ -946,17 +947,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0805_2012Metric" + (footprint "R_0402_1005Metric" (layer "F.Cu") - (uuid "1d3d471d-1b40-4759-b494-3759590e2ac6") - (at 123.8 119.315 180) - (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") - (tags "capacitor") - (property "Reference" "C_VIN_1" - (at 0 -1.68 180) + (uuid "175e8db9-931d-43d2-80d6-86f65f802aaa") + (at 146 118.6) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_EN_PU1" + (at 0 -1.17 0) (layer "F.SilkS") (hide yes) - (uuid "92798aeb-85d6-4865-8b5a-b63f2a898382") + (uuid "72bcae9d-8a00-48f6-a2f5-e88fc721b63b") (effects (font (size 1 1) @@ -964,10 +965,10 @@ ) ) ) - (property "Value" "10µF" - (at 0 1.68 180) + (property "Value" "10kΩ" + (at 0 1.17 0) (layer "F.Fab") - (uuid "3c976c53-c8a0-400e-8867-17538010d55e") + (uuid "fb9ca6e0-18da-48cd-b62e-6da5b9ace578") (effects (font (size 1 1) @@ -976,33 +977,32 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "98bf2dd7-5377-4e1f-8186-150046fd0007") + (uuid "3edeb685-f943-43ef-ac20-c6622786c459") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 180) + (property "Description" "" + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "5c4fd126-4d33-4c5a-902c-f14f004934d8") + (uuid "44014514-e13c-4ec4-bd06-700c8be9d9f5") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Samsung Electro-Mechanics" + (property "KiLib_Generator" "SMD_2terminal_chip_molded" (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (layer "F.SilkS") (hide yes) - (uuid "19913c2d-829e-4aad-ad12-a8c0fd4d9b84") + (uuid "68fb02a3-1770-4410-ab08-93953e1b7f4f") (effects (font (size 1 1) @@ -1010,141 +1010,140 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "157ab6f8-a236-4733-aef3-73534a6b42c2") + (uuid "7b182ace-298c-47ad-aee0-38b5a68cd28f") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "LCSC" "C15850" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "0402WGF1002TCE" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "8ed366da-fc44-4b02-b9e0-21d8f90a89da") + (uuid "60fcf26a-1111-48ec-8430-3af4f617638c") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Stackup Path" "C_VIN_1" - (at 0 2 180) + (property "LCSC" "C25744" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "2c974235-1d97-4cbb-85e1-fff6f355c1df") + (uuid "f6bf41b0-842a-4af3-abb7-c292d3248bc0") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:38" - (at 0 2 180) + (property "Stackup Path" "R_EN_PU1" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "3442f931-428e-48a6-b4a9-020bc1f8d17d") + (uuid "e0223970-73cb-40ad-b520-64379839fb4a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/86103b52-000a-5cd5-a338-7553101cd180") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:59" + (at 0 2 0) + (layer "F.SilkS") + (hide yes) + (uuid "aea00321-f7a8-408a-840e-6bb5a55eb434") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/5ff91a3f-185a-5324-9e45-da761fe0d3a7") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.261252 0.735) - (end 0.261252 0.735) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "6ec55279-e7e9-46c4-adde-1f4123425431") + (uuid "973f3cbc-e8f8-4f6b-8fe6-bfb9a043ef7a") ) (fp_line - (start -0.261252 -0.735) - (end 0.261252 -0.735) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "c7890148-5f3d-44fd-9a5a-e5f2bd1055a2") + (uuid "bff7697a-4a64-456f-9791-8b21144ac5ae") ) (fp_rect - (start -1.7 -0.98) - (end 1.7 0.98) + (start -0.93 -0.47) + (end 0.93 0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "32ab2798-8262-4c0b-b2c6-1de3cfe88163") + (uuid "d04dc7c0-f446-44e3-89ab-3be0fd9d3b68") ) (fp_rect - (start -1 -0.625) - (end 1 0.625) + (start -0.525 -0.27) + (end 0.525 0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "4849e0f2-fba7-4541-ab64-ca8f7b3c14cc") + (uuid "5cb72fbe-2fc0-42f8-91b6-99f2e1e27eb6") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") - (uuid "b0240c8b-4db2-4ade-b6cd-923dcc45df38") + (uuid "7ea95564-4a88-4c67-905d-09236b7f81b2") (effects (font - (size 0.5 0.5) - (thickness 0.08) + (size 0.26 0.26) + (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.95 0 180) - (size 1 1.45) + (at -0.51 0) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "VBUS") - (pintype "passive") - (uuid "fcf92e42-45bd-449b-805f-21244811038d") + (net "/MCU_Core/MCU_EN") + (uuid "0dc3fdb0-3a42-4608-974e-b20f47d39a6c") ) (pad "2" smd roundrect - (at 0.95 0 180) - (size 1 1.45) + (at 0.51 0) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "GND") - (pintype "passive") - (uuid "22c7ee91-608a-4648-b0e5-6ed42fb011e8") + (net "3V3") + (uuid "2f862d7a-ef1d-44c7-8d73-3681b6eca9d2") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -1156,17 +1155,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0805_2012Metric" + (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "F.Cu") - (uuid "2513389e-e2b0-45c2-938c-0301fd0d713f") - (at 131.475 109.8 90) - (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (uuid "38e6c729-29b0-4d22-8501-842691ea17cc") + (at 125.8 124.6 90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") - (property "Reference" "C_BUCK_OUT1" - (at 0 -1.68 90) + (property "Reference" "C_RGB1" + (at 0 -1.16 270) (layer "F.SilkS") (hide yes) - (uuid "4051d71d-2b5a-40ca-b439-7c470ea75381") + (uuid "e26be322-5ce6-4363-81e7-c35eec865150") (effects (font (size 1 1) @@ -1174,10 +1173,10 @@ ) ) ) - (property "Value" "10µF" - (at 0 1.68 90) + (property "Value" "100nF" + (at 0 0.99 270) (layer "F.Fab") - (uuid "82e7b1a7-567e-49a7-9271-1f94929512d6") + (uuid "c0e36c99-eec4-4d69-8623-eaca3a7ab10d") (effects (font (size 1 1) @@ -1186,10 +1185,10 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 270) (layer "F.Fab") (hide yes) - (uuid "21cfd4d9-ff48-4580-be44-b0d939b456b3") + (uuid "7cf0742f-9f2a-4f38-b89a-cad488512630") (effects (font (size 1.27 1.27) @@ -1197,10 +1196,10 @@ ) ) (property "Description" "Unpolarized capacitor" - (at 0 0 90) + (at 0 0 270) (layer "F.Fab") (hide yes) - (uuid "c4f828b3-dd18-4e7a-9d02-a171edb53cae") + (uuid "76d89acf-5cc5-40cb-861b-ed2854398442") (effects (font (size 1.27 1.27) @@ -1208,11 +1207,11 @@ ) ) (property "MF" "Samsung Electro-Mechanics" - (at 0 0 270) + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "c2feac37-1118-4816-b1af-7caa66b7b5a9") + (uuid "47b4e680-392a-4267-a74c-cd970ac8cefc") (effects (font (size 1 1) @@ -1220,12 +1219,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" - (at 0 0 270) + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "1de9d2a1-fcf2-45f1-a6ed-92b607e1b429") + (uuid "9108b24b-f341-46ae-8828-77bc8d09f956") (effects (font (size 1 1) @@ -1233,12 +1232,12 @@ ) ) ) - (property "LCSC" "C15850" - (at 0 0 270) + (property "LCSC" "C1525" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "2facc8dc-af31-48b2-a602-60af3575e762") + (uuid "82c66bad-1107-4dbb-926e-7b485b943231") (effects (font (size 1 1) @@ -1246,34 +1245,32 @@ ) ) ) - (property "Stackup Path" "C_BUCK_OUT1" - (at 2 0 180) + (property "Stackup Path" "C_RGB1" + (at -2 0 0) (layer "F.SilkS") (hide yes) - (uuid "6801ec0c-3ba1-48e4-b492-5ac547210be9") + (uuid "bf7553c7-653a-4165-b1b9-b1d8184c41d6") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:25" - (at 2 0 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:36" + (at -2 0 0) (layer "F.SilkS") (hide yes) - (uuid "7076765b-2e1d-4cfb-8ea5-3bce1ac1b429") + (uuid "189cccad-ab07-4a80-930c-934b63689f4b") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) (property ki_fp_filters "C_*") - (path "/9c031725-c12c-5f56-9f8e-dce0669b7cb5") + (path "/c7e1bda1-ed35-5204-8b31-f01af05098a9") (units (unit (name "A") @@ -1283,78 +1280,78 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.261252 -0.735) - (end 0.261252 -0.735) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "3a3c1d5a-a0ed-42f7-b8be-fb078e8c5f59") + (uuid "e9d9f069-4cb1-4b18-ab28-60ad19903ad8") ) (fp_line - (start -0.261252 0.735) - (end 0.261252 0.735) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "b7145f12-9f03-41c0-aee8-95ebde1519d8") + (uuid "5c90764e-f953-4fea-b326-e09b58d6d62a") ) (fp_rect - (start -1.7 -0.98) - (end 1.7 0.98) + (start -0.91 -0.46) + (end 0.91 0.46) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "ab26275f-3101-43b8-8a0b-32225b46f421") + (uuid "96d1c95d-94e2-432f-9234-ace793e675be") ) (fp_rect - (start -1 -0.625) - (end 1 0.625) + (start -0.5 -0.25) + (end 0.5 0.25) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "515e97c8-abcf-4727-be67-59b12f45c820") + (uuid "e587bc24-50d9-4886-b3fb-75357e0902d5") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 270) (layer "F.Fab") - (uuid "a7a437c7-9d7d-49ac-817e-c8d224bf4b1a") + (uuid "97b5accf-9873-4dee-8785-1cd1800cc052") (effects (font - (size 0.5 0.5) - (thickness 0.08) + (size 0.25 0.25) + (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.95 0 90) - (size 1 1.45) + (at -0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "3V3") (pintype "passive") - (uuid "d0ada20f-1079-46de-840a-2063dcbb67f2") + (uuid "83eeae7e-5953-4848-a4a1-878bceab680e") ) (pad "2" smd roundrect - (at 0.95 0 90) - (size 1 1.45) + (at 0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") (pintype "passive") - (uuid "4fa9d337-00fb-4430-9c3b-d655757bb4aa") + (uuid "2371214c-148e-4cdc-9f2d-a23b8b91b80c") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -1366,28 +1363,28 @@ ) ) ) - (footprint "Capacitor_SMD:C_0402_1005Metric" + (footprint "SW_Alps_SKRP" (layer "F.Cu") - (uuid "38e6c729-29b0-4d22-8501-842691ea17cc") - (at 127.75 123.75) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_RGB1" - (at 0 -1.16 0) + (uuid "3f83cf94-f870-45cc-a20b-93ecb451363c") + (at 147.15 114.5 90) + (descr "Alps SKRP 4.2x3.2x2.5mm tact switch, 4 pads. Land from the Alps SKRP datasheet (PC board land dimensions): 5.2/3.1 x 2.8/1.5 mm. Terminals 1-2 and 3-4 are joined inside, so pad 1 is the top pair and pad 2 the bottom pair. 3D model is the same-size C&K PTS810.") + (tags "SPST Button Switch") + (property "Reference" "SW_BOOT1" + (at 0.005 -2.334999 90) (layer "F.SilkS") (hide yes) - (uuid "e26be322-5ce6-4363-81e7-c35eec865150") + (uuid "e3cb0a6a-4ca4-47c3-b506-a9a395dc85c0") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.8 0.8) + (thickness 0.12) ) ) ) - (property "Value" "100nF" - (at 0 0.99 0) + (property "Value" "SKRPABE010" + (at 1.675 8.15 90) (layer "F.Fab") - (uuid "c0e36c99-eec4-4d69-8623-eaca3a7ab10d") + (uuid "05255947-9350-4e85-9825-129599b193b9") (effects (font (size 1 1) @@ -1396,46 +1393,359 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 90) + (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "7cf0742f-9f2a-4f38-b89a-cad488512630") + (uuid "a8e38cc8-5fe6-4fd8-8c13-43a91a35a405") (effects (font (size 1.27 1.27) + (thickness 0.15) ) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 0) + (property "Description" "" + (at 0 0 90) + (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "76d89acf-5cc5-40cb-861b-ed2854398442") + (uuid "48a9692c-d32e-43f9-b495-cd53e8a958fa") (effects (font (size 1.27 1.27) + (thickness 0.15) ) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "MF" "Alps Alpine" + (at -2 0 0) + (layer "F.SilkS") (hide yes) - (uuid "47b4e680-392a-4267-a74c-cd970ac8cefc") + (uuid "8277542c-aa73-4ea5-8a67-9fec78eedd1c") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "SKRPABE010" + (at -2 0 0) + (layer "F.SilkS") (hide yes) - (uuid "9108b24b-f341-46ae-8828-77bc8d09f956") + (uuid "b7d966ce-2490-416d-9b7b-2965ae0e1174") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "LCSC" "C115360" + (at -2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "c8399077-e80e-4225-8a2e-4e8fae984198") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "SW_BOOT1" + (at -2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "9b03ee93-8e75-4914-a323-6838ff873c49") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:77" + (at -2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "85d7efba-87c4-4cc8-b850-29127b1ad6ff") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (path "/04731770-7be7-5c5c-9ac0-967af43661c6") + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start 2.2 -1.7) + (end -2.2 -1.7) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "8fdee38a-b400-44a5-a61a-4c4b6619f561") + ) + (fp_line + (start -2.2 -1.7) + (end -2.2 -1.58) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "d11fa051-301a-4ddf-947b-c4ccc65af0df") + ) + (fp_line + (start 2.2 -1.58) + (end 2.2 -1.7) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "5d934c1d-34ed-4f01-9a3b-c6a788f88304") + ) + (fp_line + (start -2.2 -0.57) + (end -2.2 0.57) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "afc1dd0b-be47-4c65-8c8a-b007f10d9920") + ) + (fp_line + (start 2.2 0.57) + (end 2.2 -0.57) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "e11414d9-4cdf-4555-921e-a1ccf6e4fe09") + ) + (fp_line + (start -2.2 1.58) + (end -2.2 1.7) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "304aa510-e2ba-4650-a8ff-c27bb9ce4cb4") + ) + (fp_line + (start 2.2 1.7) + (end 2.2 1.58) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "98edcc55-4e27-4d6e-b8ed-ef7afbf38b22") + ) + (fp_line + (start -2.2 1.7) + (end 2.2 1.7) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "d23d79fb-bdd1-495f-96b6-1180ffcf411e") + ) + (fp_line + (start 2.85 -1.85) + (end 2.85 1.85) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "7890df47-7d7a-4c90-93be-db5fa9f695dc") + ) + (fp_line + (start -2.85 -1.85) + (end 2.85 -1.85) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "17fde1c8-cfc5-478d-8e62-8ed644202a24") + ) + (fp_line + (start 2.85 1.85) + (end -2.85 1.85) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "caf9e977-efc9-44de-ab87-0d371b762113") + ) + (fp_line + (start -2.85 1.85) + (end -2.85 -1.85) + (stroke + (width 0.05) + (type solid) + ) + (layer "F.CrtYd") + (uuid "e616d30f-327b-44e2-b93b-eb7bdff3ab1b") + ) + (fp_line + (start 2.1 -1.6) + (end -2.1 -1.6) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "a310bc9e-245f-4f5b-a3c3-5bfbb9593525") + ) + (fp_line + (start -2.1 -1.6) + (end -2.1 1.6) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "c016533b-1069-4d90-ad12-4f04f56576c8") + ) + (fp_line + (start -0.4 -1.1) + (end 0.4 -1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "acd6497d-b778-44cc-adcb-86f4e04c4cc1") + ) + (fp_line + (start 0.4 1.1) + (end -0.4 1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "74fb357d-3ffe-423c-afae-b2359b8c1c53") + ) + (fp_line + (start 2.1 1.6) + (end 2.1 -1.6) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "9fb3fe7c-1026-4b0f-a7e6-7edefc2a00b7") + ) + (fp_line + (start -2.1 1.6) + (end 2.1 1.6) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "9b5f2db8-b7e4-47d2-8cc8-109afdb87355") + ) + (fp_arc + (start 0.4 -1.1) + (mid 1.5 0) + (end 0.4 1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "a11f0749-f6ae-458b-b84a-40aadd4a7d48") + ) + (fp_arc + (start -0.4 1.1) + (mid -1.5 0) + (end -0.4 -1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "e40f9b23-7ca2-4a49-9b62-668ec0bb1e86") + ) + (fp_text user "${REFERENCE}" + (at 1.675 5.55 90) + (layer "F.Fab") + (uuid "7afe7d61-532e-4e6b-9522-a726563c1cc1") + (effects + (font + (size 0.6 0.6) + (thickness 0.09) + ) + ) + ) + (pad "1" smd rect + (at -2.075 -1.075 90) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "958c36fe-269d-4e38-b7cc-28186e3b6589") + ) + (pad "1" smd rect + (at 2.075 -1.075 90) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "cca9a5af-a604-4069-9af6-a0dcafa16afa") + ) + (pad "2" smd rect + (at -2.075 1.075 90) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/MCU_BOOT") + (uuid "6d3f76dd-3479-42ab-ba72-1be271e462cc") + ) + (pad "2" smd rect + (at 2.075 1.075 90) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/MCU_BOOT") + (uuid "b06922c9-5384-454f-a2a3-a9c27a2699da") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Button_Switch_SMD.3dshapes/SW_SPST_PTS810.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) + (footprint "C_0402_1005Metric" + (layer "F.Cu") + (uuid "4211ee0a-ab80-46ad-8319-8723fea825d9") + (at 131.6 103.35 90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_TRIG1" + (at 0 -1.16 90) + (layer "F.SilkS") + (hide yes) + (uuid "b1cc8d05-c797-4502-8544-63c71da3c94d") (effects (font (size 1 1) @@ -1443,12 +1753,44 @@ ) ) ) - (property "LCSC" "C1525" - (at 0 0 0) - (unlocked yes) + (property "Value" "100nF" + (at 0 1.16 90) + (layer "F.Fab") + (uuid "1cc30b57-38fe-4591-8d65-2d499f630079") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Datasheet" "" + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "82c66bad-1107-4dbb-926e-7b485b943231") + (uuid "754dcd4b-6c4c-4745-afac-16f704523ae4") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "Description" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "8edf0cdb-f163-4dd4-9251-132dc9af83a9") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 90) + (layer "F.SilkS") + (hide yes) + (uuid "c7904181-74b3-47bd-aeee-c76eaa78b9c8") (effects (font (size 1 1) @@ -1456,11 +1798,11 @@ ) ) ) - (property "Stackup Path" "C_RGB1" - (at -2 0 270) + (property "MF" "Samsung Electro-Mechanics" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "bf7553c7-653a-4165-b1b9-b1d8184c41d6") + (uuid "02cb9ee3-038f-41db-a8ac-734a63a70e9b") (effects (font (size 1.27 1.27) @@ -1468,11 +1810,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:34" - (at -2 0 270) + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "189cccad-ab07-4a80-930c-934b63689f4b") + (uuid "8d2cf348-7803-427a-af9e-5127201556b2") (effects (font (size 1.27 1.27) @@ -1480,14 +1822,43 @@ ) ) ) - (property ki_fp_filters "C_*") - (path "/c7e1bda1-ed35-5204-8b31-f01af05098a9") - (units - (unit - (name "A") - (pins "1" "2") + (property "LCSC" "C1525" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "5af47887-fad1-41c2-bfd2-abfa586b198a") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "C_TRIG1" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "a5bdac34-608e-4ebc-a5f7-043d07538243") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:105" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "d22a85aa-50c6-4100-8cb4-8683599ae546") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/f3b6ba4d-8858-5241-8647-ebaa5466f9f2") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line @@ -1498,7 +1869,7 @@ (type solid) ) (layer "F.SilkS") - (uuid "e9d9f069-4cb1-4b18-ab28-60ad19903ad8") + (uuid "c407f862-c614-4452-80af-0369c6b21fed") ) (fp_line (start -0.107836 0.36) @@ -1508,7 +1879,7 @@ (type solid) ) (layer "F.SilkS") - (uuid "5c90764e-f953-4fea-b326-e09b58d6d62a") + (uuid "35753784-67fc-4ae2-abe2-f294d4d78a64") ) (fp_rect (start -0.91 -0.46) @@ -1519,7 +1890,7 @@ ) (fill no) (layer "F.CrtYd") - (uuid "96d1c95d-94e2-432f-9234-ace793e675be") + (uuid "54f6352c-1946-4564-ace5-07e490fe7dc7") ) (fp_rect (start -0.5 -0.25) @@ -1530,12 +1901,12 @@ ) (fill no) (layer "F.Fab") - (uuid "e587bc24-50d9-4886-b3fb-75357e0902d5") + (uuid "0afed501-bbcf-4ea0-b2d1-9129291908aa") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") - (uuid "97b5accf-9873-4dee-8785-1cd1800cc052") + (uuid "7125f04d-c78f-443b-afe2-85690d1dddd1") (effects (font (size 0.25 0.25) @@ -1544,22 +1915,20 @@ ) ) (pad "1" smd roundrect - (at -0.48 0) + (at -0.48 0 90) (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "3V3") - (pintype "passive") - (uuid "83eeae7e-5953-4848-a4a1-878bceab680e") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "36edfd92-46b9-4e21-9c0a-faeb453c6cc1") ) (pad "2" smd roundrect - (at 0.48 0) + (at 0.48 0 90) (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "2371214c-148e-4cdc-9f2d-a23b8b91b80c") + (uuid "b0facdce-0334-47d0-a9bf-63291bdf031c") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" @@ -1741,7 +2110,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:76" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:79" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -2010,17 +2379,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0805_2012Metric" + (footprint "C_0603_1608Metric" (layer "F.Cu") - (uuid "4e10f49e-2dcc-4c78-9962-5b2c41ec36bf") - (at 139.95 114.3 180) - (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (uuid "5f5f1d7b-9c0d-42c1-ab87-9ead6d78687d") + (at 146 120.3) + (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") - (property "Reference" "C_BUCK_IN1" - (at 0 -1.68 180) + (property "Reference" "C_EN1" + (at 0 -1.43 0) (layer "F.SilkS") (hide yes) - (uuid "023e560f-cab2-4cec-9c89-7a1ae3d6ea74") + (uuid "ddf8553b-16bc-42bb-9cf4-aad61181551c") (effects (font (size 1 1) @@ -2028,10 +2397,10 @@ ) ) ) - (property "Value" "10µF" - (at 0 1.68 180) + (property "Value" "1µF" + (at 0 1.43 0) (layer "F.Fab") - (uuid "248c280c-de87-40b8-8254-606146450ed9") + (uuid "6e924c94-b989-4c05-87de-dd5a84de91d4") (effects (font (size 1 1) @@ -2040,33 +2409,32 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "d6c82177-c5b6-4ff6-a553-0d916b0002ab") + (uuid "34218270-cdda-462d-afce-aae91b643066") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 180) + (property "Description" "" + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "a9201686-5b28-4e4d-8f99-92ac80616fb7") + (uuid "3031215e-2403-4a39-bed2-6345f829fe5c") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Samsung Electro-Mechanics" + (property "KiLib_Generator" "SMD_2terminal_chip_molded" (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (layer "F.SilkS") (hide yes) - (uuid "0d92eea3-6382-4561-80fd-d4130f6e6138") + (uuid "3ad4ef43-df65-44b6-b392-9a49fed43e5c") (effects (font (size 1 1) @@ -2074,141 +2442,140 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "MF" "Samsung Electro-Mechanics" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "fa6e0712-5f41-4b68-b84f-36fcf341bf46") + (uuid "757e82a1-9b13-40cd-af96-698e5af4257f") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "LCSC" "C15850" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "CL10A105KB8NNNC" + (at 0 2 0) + (layer "F.SilkS") (hide yes) - (uuid "123c97d9-47f5-4b56-898e-634f2fe303ac") + (uuid "c6aec1cf-bd55-42d1-9a2c-9a5d86f371ee") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Stackup Path" "C_BUCK_IN1" - (at 0 2 180) + (property "LCSC" "C15849" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "7a91119b-5282-4cce-966d-768c9aac5324") + (uuid "6213b3c6-c551-48de-86d3-5b93e8f1c36a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:24" - (at 0 2 180) + (property "Stackup Path" "C_EN1" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "d12f8c26-3e7d-4139-8511-9ddbef7ac3d7") + (uuid "d8f30679-9050-4ef9-8dff-04369bd57dd6") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/d5366359-0189-584f-bdba-ca23d6aa7d16") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:27" + (at 0 2 0) + (layer "F.SilkS") + (hide yes) + (uuid "58df513d-d10e-4327-80a6-176116a7b3df") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/4dc673dd-bc14-553a-834a-9cee5f4e59f8") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.261252 0.735) - (end 0.261252 0.735) + (start -0.14058 -0.51) + (end 0.14058 -0.51) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "8a970c10-a955-433b-91ab-5cbc861a9f42") + (uuid "6cef0af0-3ce2-48a6-916e-e6166634bb50") ) (fp_line - (start -0.261252 -0.735) - (end 0.261252 -0.735) + (start -0.14058 0.51) + (end 0.14058 0.51) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "8cd131c5-a571-4852-a5c3-2a5bf9506838") + (uuid "94ddc625-a5c4-4567-9a72-1909a9a0c975") ) (fp_rect - (start -1.7 -0.98) - (end 1.7 0.98) + (start -1.48 -0.73) + (end 1.48 0.73) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "eddc8c1b-5147-4431-a679-2aa96cac0b95") + (uuid "4102ce23-58a7-4667-b299-136903844678") ) (fp_rect - (start -1 -0.625) - (end 1 0.625) + (start -0.8 -0.4) + (end 0.8 0.4) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "f4d996e5-8d52-4f68-a726-6dd911b40aca") + (uuid "8fd275ee-bc9a-4758-b1ef-64d8e52becb9") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") - (uuid "6036687a-6def-4d1b-80d5-38cadc3d6755") + (uuid "6aa830a9-0091-4c27-8793-1d8c51ddd2c4") (effects (font - (size 0.5 0.5) - (thickness 0.08) + (size 0.4 0.4) + (thickness 0.06) ) ) ) (pad "1" smd roundrect - (at -0.95 0 180) - (size 1 1.45) + (at -0.775 0) + (size 0.9 0.95) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "VSYS") - (pintype "passive") - (uuid "69b83c4f-9be7-48ea-9ffe-f8da0c826497") + (net "/MCU_Core/MCU_EN") + (uuid "d629789c-886e-4b5f-b188-bba54787f2c3") ) (pad "2" smd roundrect - (at 0.95 0 180) - (size 1 1.45) + (at 0.775 0) + (size 0.9 0.95) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "2b613f3c-9fd5-4662-a95c-903c2ef2b3e5") + (uuid "1dba74a3-a803-4c02-b334-b12d104b89fd") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" (offset (xyz 0 0 0) ) @@ -2220,17 +2587,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0402_1005Metric" + (footprint "R_0402_1005Metric" (layer "F.Cu") - (uuid "6c065ac4-f64b-4312-bde9-e1c4595b72fa") - (at 132.25 119.835 90) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_SYS_2" - (at 0 -1.16 90) + (uuid "629dda5b-869f-49c5-93a4-eb7c153199f9") + (at 128.02 114.46 90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_USB_DM1" + (at 0 -1.17 90) (layer "F.SilkS") (hide yes) - (uuid "9537b2d9-04c1-4bb4-968b-064284a132d2") + (uuid "2e6f51da-c87a-4d75-a124-adbcf26cd290") (effects (font (size 1 1) @@ -2238,10 +2605,10 @@ ) ) ) - (property "Value" "100nF" - (at 0 1.16 90) + (property "Value" "27Ω" + (at 0 1.17 90) (layer "F.Fab") - (uuid "51e5f2c8-7140-4978-af3a-5690f99018b2") + (uuid "cb67406b-1531-4432-b914-bc74354f5fb3") (effects (font (size 1 1) @@ -2253,30 +2620,29 @@ (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "a53a392f-8223-41b9-aa5a-49ad740c19ec") + (uuid "3f584b5f-4c03-4a79-b38d-fa39df5bd7e3") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Unpolarized capacitor" + (property "Description" "" (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "2fae936d-defa-4080-8588-17ab4e1bab63") + (uuid "7e1cd0e5-d3fd-431f-9e09-75ce9f650a3d") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 90) + (layer "F.SilkS") (hide yes) - (uuid "8ec8f803-2729-42b8-b115-8c328158c379") + (uuid "26ee2b55-45d1-4fc7-aba2-fcb2e447e3be") (effects (font (size 1 1) @@ -2284,141 +2650,140 @@ ) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "MF" "Yageo" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "cccc6388-0134-4240-87a0-c17d1f7d9b32") + (uuid "f899ed07-9877-442f-864c-016c8c72afb8") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "LCSC" "C1525" - (at 0 0 270) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "RC0402FR-0727RL" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "4b4fbbef-6501-43d2-9918-84529b4813d9") + (uuid "33a90072-09fc-4a33-b335-97235aee388e") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Stackup Path" "C_SYS_2" - (at 2 0 180) + (property "LCSC" "C138021" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "cbbb5024-eba7-432a-9f6c-ad412f43fb74") + (uuid "cd1252c2-6a1a-4128-8176-09a34f700e85") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:37" - (at 2 0 180) + (property "Stackup Path" "R_USB_DM1" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "56705001-f4f7-44f0-8a76-bd986d316c30") + (uuid "e8f33cbc-9132-466f-b7bd-cdaef3c2000a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/e2c8fc08-1aa6-5675-9020-a7b835e59054") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:72" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "0d09e0fe-e071-4e28-9c7e-6b11dfa8659a") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/c96e0117-7853-5f35-986f-299234d32874") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "13541b1a-7867-43cd-bec1-b269b037414c") + (uuid "1b502fc0-675a-4ae6-b8e0-324ef1926251") ) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "a0d76405-9be5-4fbc-ab2f-69fa5d4d815f") + (uuid "e3aa2cec-2351-4191-aa41-18263dc5ec77") ) (fp_rect - (start -0.91 -0.46) - (end 0.91 0.46) + (start -0.93 -0.47) + (end 0.93 0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "68484eac-d015-4ccd-b789-c17b315171b0") + (uuid "c69a5227-8e6b-4b26-ba98-63a36c1caafb") ) (fp_rect - (start -0.5 -0.25) - (end 0.5 0.25) + (start -0.525 -0.27) + (end 0.525 0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "7bd128d4-e869-402d-87d3-a92fe78051f5") + (uuid "42360b3a-d6f8-495a-b010-dc788a1e497a") ) (fp_text user "${REFERENCE}" (at 0 0 90) (layer "F.Fab") - (uuid "317a5d3b-afa4-4a1e-9207-a7cd367d9f7d") + (uuid "9899a650-7ab5-4711-a172-b5d1d18cc591") (effects (font - (size 0.25 0.25) + (size 0.26 0.26) (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.48 0 90) - (size 0.56 0.62) + (at -0.51 0 90) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "VSYS") - (pintype "passive") - (uuid "d0925c20-c808-4901-a072-2ae07f61bad6") + (net "/MCU_Core/USB_DM") + (uuid "53609738-63a0-4a77-b34e-b109231cbcc2") ) (pad "2" smd roundrect - (at 0.48 0 90) - (size 0.56 0.62) + (at 0.51 0 90) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "GND") - (pintype "passive") - (uuid "2ab3e196-cfee-49bf-9884-10a466fa28dd") + (net "/MCU_Core/USB_DM_MCU") + (uuid "1721ee9e-d714-4c9d-a211-864ec9985eb0") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -2536,7 +2901,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:83" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:86" (at 2 0 0) (layer "F.SilkS") (hide yes) @@ -2982,7 +3347,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:80" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:83" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -3354,7 +3719,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:77" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:80" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -3726,7 +4091,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:75" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:78" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -4094,7 +4459,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:43" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:45" (at 0 2 90) (layer "F.SilkS") (hide yes) @@ -4218,216 +4583,6 @@ ) ) ) - (footprint "Capacitor_SMD:C_0805_2012Metric" - (layer "F.Cu") - (uuid "7c3e1bde-ed4c-4163-a923-82af23ae1287") - (at 134.2 116.815) - (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") - (tags "capacitor") - (property "Reference" "C_BAT1" - (at 0 -1.68 180) - (layer "F.SilkS") - (hide yes) - (uuid "c10a7e00-8276-4583-a2d6-037815246ffc") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Value" "10µF" - (at 0 1.68 180) - (layer "F.Fab") - (uuid "749c8d9a-e32d-421f-bf57-c3ee34a4d812") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Datasheet" "" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "873e446a-728e-42db-b4d9-27f5c3127f8a") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "Description" "Unpolarized capacitor" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "b972fe71-db34-4246-abe9-96bb9b411b90") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "6c2e7b0d-81c9-424e-b800-5d3214baba9b") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "aba0e959-1a1d-465e-90c8-45e4fbf12314") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "LCSC" "C15850" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "1c86887f-f997-4fab-93a1-88dfdcad1cb3") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Stackup Path" "C_BAT1" - (at 0 -2 180) - (layer "F.SilkS") - (hide yes) - (uuid "801866e9-25be-41b1-ade4-320126f18d7d") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:23" - (at 0 -2 180) - (layer "F.SilkS") - (hide yes) - (uuid "79058ded-645d-467b-8e52-e745eb240519") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property ki_fp_filters "C_*") - (path "/53994c88-33fa-516a-9d64-2f0949cf1a73") - (units - (unit - (name "A") - (pins "1" "2") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.261252 -0.735) - (end 0.261252 -0.735) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "f98e28b1-5af7-4261-a0dd-d6375cceaa78") - ) - (fp_line - (start -0.261252 0.735) - (end 0.261252 0.735) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "d9e928c4-100b-42b9-b513-270d0ea83806") - ) - (fp_rect - (start -1.7 -0.98) - (end 1.7 0.98) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "a242494c-fef1-4e58-8845-ae4c1152b650") - ) - (fp_rect - (start -1 -0.625) - (end 1 0.625) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "F.Fab") - (uuid "925473b7-2a42-4bda-a61c-e929c55545f7") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "F.Fab") - (uuid "12df748f-8b5c-4667-a0ec-3cb8d5190dc9") - (effects - (font - (size 0.5 0.5) - (thickness 0.08) - ) - ) - ) - (pad "1" smd roundrect - (at -0.95 0) - (size 1 1.45) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "VBAT") - (pintype "passive") - (uuid "97810122-0162-4a84-b675-d47562c9c5e8") - ) - (pad "2" smd roundrect - (at 0.95 0) - (size 1 1.45) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "GND") - (pintype "passive") - (uuid "1f420529-9c3f-416d-991b-6bd2ece3a600") - ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) (footprint "MountingHole:MountingHole_2.2mm_M2_ISO14580" (layer "F.Cu") (uuid "815f88e5-e801-4c8f-8c62-2a93ed32cb88") @@ -4535,15 +4690,17 @@ ) (embedded_fonts no) ) - (footprint "BQ25185DLHR:IC_BQ25185DLHR" + (footprint "Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal" (layer "F.Cu") - (uuid "836984b6-78b1-47fe-abee-4e3e5d3947c9") - (at 129.75 118.315 180) - (property "Reference" "U_CHG1" - (at 1.625 -2.385 180) + (uuid "87312f15-4904-4812-a8ac-fdb6935b1b62") + (at 124.4 110.125) + (descr "JST SH series connector, SM04B-SRSS-TB (http://www.jst-mfg.com/product/pdf/eng/eSH.pdf)") + (tags "connector JST SH horizontal") + (property "Reference" "U_OLED1" + (at 0 -3.98 0) (layer "F.SilkS") (hide yes) - (uuid "2f641c96-19e9-456c-a079-4588a1c17c8e") + (uuid "f21dabe4-0ea4-4e61-b82e-82b28a04106e") (effects (font (size 1 1) @@ -4551,10 +4708,10 @@ ) ) ) - (property "Value" "BQ25185DLHR" - (at 3 -0.48 180) + (property "Value" "Qwiic connector" + (at 0 3.98 0) (layer "F.Fab") - (uuid "937d09f5-09df-4d6b-8572-16fb39cbd9a6") + (uuid "b39ff267-ef08-4c6e-a552-2cdcf02d59cc") (effects (font (size 1 1) @@ -4563,202 +4720,33 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "96cab20e-4629-450a-9947-3832773ddea6") + (uuid "ef9daf8e-5ed6-45a6-9ede-18c6d3b6566e") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "1-cell, 1-A stand-alone linear battery charger with power path and solar input support" - (at 0 0 180) + (property "Description" "Generic 4-pin I2C SSD1306 OLED breakout module (VCC, GND, SCL, SDA). Hand-authored project-local symbol, no vendor-specific pinout assumed." + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "d9c65078-d834-4ff3-a90a-3c7453bb0539") + (uuid "656a6174-b20e-4651-9a29-2e8631c93b4f") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Texas Instruments" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "35792020-4129-42f5-bb24-953453bc3238") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "SNAPEDA_PACKAGE_ID" "124517" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "d59e212a-22d4-46b8-9873-85040c5da429") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "CREATOR" "AMINA" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "e957fd6b-78d6-470b-bc48-e933fb5a37d6") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Price" "None" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "4ca0f772-4a36-462e-b05c-23ad06e5053c") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Package" "WFDFN-10 Texas Instruments" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "d0b02736-bfa7-4e3d-80a1-97cc94045708") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Check_prices" "https://www.snapeda.com/parts/BQ25185DLHR/Texas+Instruments/view-part/?ref=eda" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "9b1188a6-64e1-43c1-a1fb-63848eadf0bf") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "STANDARD" "Manufacturer Recommendations" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "27d6abc6-8624-40de-98b7-55fe9527c3e6") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "PARTREV" "OCTOBER 2023" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "9f1dbd7f-213d-4068-bc06-c1edb7a0eff3") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "VERIFIER" "" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "66178d75-9239-4a3a-afd4-59448f0851a5") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "SnapEDA_Link" "https://www.snapeda.com/parts/BQ25185DLHR/Texas+Instruments/view-part/?ref=snap" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "d0350a09-dd0a-43e1-a20d-570dbbb65b3e") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "MP" "BQ25185DLHR" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "042db2af-b233-4164-be70-998b4c27197d") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "MAXIMUM_PACKAGE_HEIGHT" "0.8mm" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "282cea84-e82d-442c-a8eb-9f89a4d2ec74") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Availability" "In Stock" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "8f997946-42bf-4b9a-8082-c29c47137a56") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "MANUFACTURER" "Texas Instruments" - (at 0 0 180) + (property "MF" "JST" + (at 0 0 0) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "d936b382-e49f-4267-ade0-387a3dadc50e") + (uuid "50ac44ff-b9a7-4ece-9195-37b7e3cb46c0") (effects (font (size 1 1) @@ -4766,12 +4754,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "BQ25185DLHR" + (property "Manufacturer_Part_Number" "SM04B-SRSS-TB(LF)(SN)" (at 0 0 0) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "0620b229-c858-4a88-a509-f0d502384867") + (uuid "a8329894-1013-428a-868d-ae2ca82697bf") (effects (font (size 1 1) @@ -4779,12 +4767,12 @@ ) ) ) - (property "LCSC" "C19725033" + (property "LCSC" "C160404" (at 0 0 0) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "ab69d5d2-eeeb-4a2e-84fb-56471cf467a2") + (uuid "35423f89-6f6a-4e1f-ac14-27caae246ed1") (effects (font (size 1 1) @@ -4792,690 +4780,386 @@ ) ) ) - (property "Stackup Path" "U_CHG1" - (at 0 2 180) + (property "Stackup Path" "U_OLED1" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "942c6526-d2c5-4606-97b7-75f29077e200") + (uuid "edd50709-92fa-42d6-8191-2d757fe8aa90") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:88" - (at 0 2 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:108" + (at 0 2 0) (layer "F.SilkS") (hide yes) - (uuid "10443bf1-9da8-4fbf-b274-0cdd37cabe12") + (uuid "c005a554-d664-4485-860d-d0ff988fd68d") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (path "/b840e28f-4d8e-5da5-89df-017c48c36ef1") + (path "/873c651e-8375-5f6a-839c-0927d0e7d3c1") (units (unit (name "A") - (pins "10" "9" "3" "4" "7" "8" "1" "2" "6" "11" "5") + (pins "2" "1" "4" "3") ) ) (attr smd) (duplicate_pad_numbers_are_jumpers no) - (fp_poly - (pts - (xy 0.75 0.9) (xy 0.75 0.7) (xy 0.75 0.697) (xy 0.75 0.695) (xy 0.751 0.692) (xy 0.751 0.69) (xy 0.752 0.687) - (xy 0.752 0.685) (xy 0.753 0.682) (xy 0.754 0.68) (xy 0.755 0.677) (xy 0.757 0.675) (xy 0.758 0.673) - (xy 0.76 0.671) (xy 0.761 0.669) (xy 0.763 0.667) (xy 0.765 0.665) (xy 0.767 0.663) (xy 0.769 0.661) - (xy 0.771 0.66) (xy 0.773 0.658) (xy 0.775 0.657) (xy 0.777 0.655) (xy 0.78 0.654) (xy 0.782 0.653) - (xy 0.785 0.652) (xy 0.787 0.652) (xy 0.79 0.651) (xy 0.792 0.651) (xy 0.795 0.65) (xy 0.797 0.65) - (xy 0.8 0.65) (xy 1.3 0.65) (xy 1.303 0.65) (xy 1.305 0.65) (xy 1.308 0.651) (xy 1.31 0.651) (xy 1.313 0.652) - (xy 1.315 0.652) (xy 1.318 0.653) (xy 1.32 0.654) (xy 1.323 0.655) (xy 1.325 0.657) (xy 1.327 0.658) - (xy 1.329 0.66) (xy 1.331 0.661) (xy 1.333 0.663) (xy 1.335 0.665) (xy 1.337 0.667) (xy 1.339 0.669) - (xy 1.34 0.671) (xy 1.342 0.673) (xy 1.343 0.675) (xy 1.345 0.677) (xy 1.346 0.68) (xy 1.347 0.682) - (xy 1.348 0.685) (xy 1.348 0.687) (xy 1.349 0.69) (xy 1.349 0.692) (xy 1.35 0.695) (xy 1.35 0.697) - (xy 1.35 0.7) (xy 1.35 0.9) (xy 1.35 0.903) (xy 1.35 0.905) (xy 1.349 0.908) (xy 1.349 0.91) (xy 1.348 0.913) - (xy 1.348 0.915) (xy 1.347 0.918) (xy 1.346 0.92) (xy 1.345 0.923) (xy 1.343 0.925) (xy 1.342 0.927) - (xy 1.34 0.929) (xy 1.339 0.931) (xy 1.337 0.933) (xy 1.335 0.935) (xy 1.333 0.937) (xy 1.331 0.939) - (xy 1.329 0.94) (xy 1.327 0.942) (xy 1.325 0.943) (xy 1.323 0.945) (xy 1.32 0.946) (xy 1.318 0.947) - (xy 1.315 0.948) (xy 1.313 0.948) (xy 1.31 0.949) (xy 1.308 0.949) (xy 1.305 0.95) (xy 1.303 0.95) - (xy 1.3 0.95) (xy 0.8 0.95) (xy 0.797 0.95) (xy 0.795 0.95) (xy 0.792 0.949) (xy 0.79 0.949) (xy 0.787 0.948) - (xy 0.785 0.948) (xy 0.782 0.947) (xy 0.78 0.946) (xy 0.777 0.945) (xy 0.775 0.943) (xy 0.773 0.942) - (xy 0.771 0.94) (xy 0.769 0.939) (xy 0.767 0.937) (xy 0.765 0.935) (xy 0.763 0.933) (xy 0.761 0.931) - (xy 0.76 0.929) (xy 0.758 0.927) (xy 0.757 0.925) (xy 0.755 0.923) (xy 0.754 0.92) (xy 0.753 0.918) - (xy 0.752 0.915) (xy 0.752 0.913) (xy 0.751 0.91) (xy 0.751 0.908) (xy 0.75 0.905) (xy 0.75 0.903) - (xy 0.75 0.9) - ) + (fp_line + (start -3.11 -1.785) + (end -2.06 -1.785) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "3a99eb35-edff-45d8-a202-17ec38d8b407") + (layer "F.SilkS") + (uuid "8a8c14b7-7341-4bba-90c7-bf6ca2706aaa") ) - (fp_poly - (pts - (xy 0.75 0.5) (xy 0.75 0.3) (xy 0.75 0.297) (xy 0.75 0.295) (xy 0.751 0.292) (xy 0.751 0.29) (xy 0.752 0.287) - (xy 0.752 0.285) (xy 0.753 0.282) (xy 0.754 0.28) (xy 0.755 0.277) (xy 0.757 0.275) (xy 0.758 0.273) - (xy 0.76 0.271) (xy 0.761 0.269) (xy 0.763 0.267) (xy 0.765 0.265) (xy 0.767 0.263) (xy 0.769 0.261) - (xy 0.771 0.26) (xy 0.773 0.258) (xy 0.775 0.257) (xy 0.777 0.255) (xy 0.78 0.254) (xy 0.782 0.253) - (xy 0.785 0.252) (xy 0.787 0.252) (xy 0.79 0.251) (xy 0.792 0.251) (xy 0.795 0.25) (xy 0.797 0.25) - (xy 0.8 0.25) (xy 1.3 0.25) (xy 1.303 0.25) (xy 1.305 0.25) (xy 1.308 0.251) (xy 1.31 0.251) (xy 1.313 0.252) - (xy 1.315 0.252) (xy 1.318 0.253) (xy 1.32 0.254) (xy 1.323 0.255) (xy 1.325 0.257) (xy 1.327 0.258) - (xy 1.329 0.26) (xy 1.331 0.261) (xy 1.333 0.263) (xy 1.335 0.265) (xy 1.337 0.267) (xy 1.339 0.269) - (xy 1.34 0.271) (xy 1.342 0.273) (xy 1.343 0.275) (xy 1.345 0.277) (xy 1.346 0.28) (xy 1.347 0.282) - (xy 1.348 0.285) (xy 1.348 0.287) (xy 1.349 0.29) (xy 1.349 0.292) (xy 1.35 0.295) (xy 1.35 0.297) - (xy 1.35 0.3) (xy 1.35 0.5) (xy 1.35 0.503) (xy 1.35 0.505) (xy 1.349 0.508) (xy 1.349 0.51) (xy 1.348 0.513) - (xy 1.348 0.515) (xy 1.347 0.518) (xy 1.346 0.52) (xy 1.345 0.523) (xy 1.343 0.525) (xy 1.342 0.527) - (xy 1.34 0.529) (xy 1.339 0.531) (xy 1.337 0.533) (xy 1.335 0.535) (xy 1.333 0.537) (xy 1.331 0.539) - (xy 1.329 0.54) (xy 1.327 0.542) (xy 1.325 0.543) (xy 1.323 0.545) (xy 1.32 0.546) (xy 1.318 0.547) - (xy 1.315 0.548) (xy 1.313 0.548) (xy 1.31 0.549) (xy 1.308 0.549) (xy 1.305 0.55) (xy 1.303 0.55) - (xy 1.3 0.55) (xy 0.8 0.55) (xy 0.797 0.55) (xy 0.795 0.55) (xy 0.792 0.549) (xy 0.79 0.549) (xy 0.787 0.548) - (xy 0.785 0.548) (xy 0.782 0.547) (xy 0.78 0.546) (xy 0.777 0.545) (xy 0.775 0.543) (xy 0.773 0.542) - (xy 0.771 0.54) (xy 0.769 0.539) (xy 0.767 0.537) (xy 0.765 0.535) (xy 0.763 0.533) (xy 0.761 0.531) - (xy 0.76 0.529) (xy 0.758 0.527) (xy 0.757 0.525) (xy 0.755 0.523) (xy 0.754 0.52) (xy 0.753 0.518) - (xy 0.752 0.515) (xy 0.752 0.513) (xy 0.751 0.51) (xy 0.751 0.508) (xy 0.75 0.505) (xy 0.75 0.503) - (xy 0.75 0.5) - ) + (fp_line + (start -3.11 0.715) + (end -3.11 -1.785) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "25ee01e6-ff77-485f-afd8-373dc7111d4b") + (layer "F.SilkS") + (uuid "e43be91c-48c8-4187-9b8f-55d03efe785e") ) - (fp_poly - (pts - (xy 0.75 0.1) (xy 0.75 -0.1) (xy 0.75 -0.103) (xy 0.75 -0.105) (xy 0.751 -0.108) (xy 0.751 -0.11) - (xy 0.752 -0.113) (xy 0.752 -0.115) (xy 0.753 -0.118) (xy 0.754 -0.12) (xy 0.755 -0.123) (xy 0.757 -0.125) - (xy 0.758 -0.127) (xy 0.76 -0.129) (xy 0.761 -0.131) (xy 0.763 -0.133) (xy 0.765 -0.135) (xy 0.767 -0.137) - (xy 0.769 -0.139) (xy 0.771 -0.14) (xy 0.773 -0.142) (xy 0.775 -0.143) (xy 0.777 -0.145) (xy 0.78 -0.146) - (xy 0.782 -0.147) (xy 0.785 -0.148) (xy 0.787 -0.148) (xy 0.79 -0.149) (xy 0.792 -0.149) (xy 0.795 -0.15) - (xy 0.797 -0.15) (xy 0.8 -0.15) (xy 1.3 -0.15) (xy 1.303 -0.15) (xy 1.305 -0.15) (xy 1.308 -0.149) - (xy 1.31 -0.149) (xy 1.313 -0.148) (xy 1.315 -0.148) (xy 1.318 -0.147) (xy 1.32 -0.146) (xy 1.323 -0.145) - (xy 1.325 -0.143) (xy 1.327 -0.142) (xy 1.329 -0.14) (xy 1.331 -0.139) (xy 1.333 -0.137) (xy 1.335 -0.135) - (xy 1.337 -0.133) (xy 1.339 -0.131) (xy 1.34 -0.129) (xy 1.342 -0.127) (xy 1.343 -0.125) (xy 1.345 -0.123) - (xy 1.346 -0.12) (xy 1.347 -0.118) (xy 1.348 -0.115) (xy 1.348 -0.113) (xy 1.349 -0.11) (xy 1.349 -0.108) - (xy 1.35 -0.105) (xy 1.35 -0.103) (xy 1.35 -0.1) (xy 1.35 0.1) (xy 1.35 0.103) (xy 1.35 0.105) (xy 1.349 0.108) - (xy 1.349 0.11) (xy 1.348 0.113) (xy 1.348 0.115) (xy 1.347 0.118) (xy 1.346 0.12) (xy 1.345 0.123) - (xy 1.343 0.125) (xy 1.342 0.127) (xy 1.34 0.129) (xy 1.339 0.131) (xy 1.337 0.133) (xy 1.335 0.135) - (xy 1.333 0.137) (xy 1.331 0.139) (xy 1.329 0.14) (xy 1.327 0.142) (xy 1.325 0.143) (xy 1.323 0.145) - (xy 1.32 0.146) (xy 1.318 0.147) (xy 1.315 0.148) (xy 1.313 0.148) (xy 1.31 0.149) (xy 1.308 0.149) - (xy 1.305 0.15) (xy 1.303 0.15) (xy 1.3 0.15) (xy 0.8 0.15) (xy 0.797 0.15) (xy 0.795 0.15) (xy 0.792 0.149) - (xy 0.79 0.149) (xy 0.787 0.148) (xy 0.785 0.148) (xy 0.782 0.147) (xy 0.78 0.146) (xy 0.777 0.145) - (xy 0.775 0.143) (xy 0.773 0.142) (xy 0.771 0.14) (xy 0.769 0.139) (xy 0.767 0.137) (xy 0.765 0.135) - (xy 0.763 0.133) (xy 0.761 0.131) (xy 0.76 0.129) (xy 0.758 0.127) (xy 0.757 0.125) (xy 0.755 0.123) - (xy 0.754 0.12) (xy 0.753 0.118) (xy 0.752 0.115) (xy 0.752 0.113) (xy 0.751 0.11) (xy 0.751 0.108) - (xy 0.75 0.105) (xy 0.75 0.103) (xy 0.75 0.1) - ) + (fp_line + (start -2.06 -1.785) + (end -2.06 -2.775) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "bf0d7d86-821f-4d0d-9f68-e1ab9c42582a") + (layer "F.SilkS") + (uuid "5c49bbc3-38c7-4683-a283-2a5a2587fed5") ) - (fp_poly - (pts - (xy 0.75 -0.3) (xy 0.75 -0.5) (xy 0.75 -0.503) (xy 0.75 -0.505) (xy 0.751 -0.508) (xy 0.751 -0.51) - (xy 0.752 -0.513) (xy 0.752 -0.515) (xy 0.753 -0.518) (xy 0.754 -0.52) (xy 0.755 -0.523) (xy 0.757 -0.525) - (xy 0.758 -0.527) (xy 0.76 -0.529) (xy 0.761 -0.531) (xy 0.763 -0.533) (xy 0.765 -0.535) (xy 0.767 -0.537) - (xy 0.769 -0.539) (xy 0.771 -0.54) (xy 0.773 -0.542) (xy 0.775 -0.543) (xy 0.777 -0.545) (xy 0.78 -0.546) - (xy 0.782 -0.547) (xy 0.785 -0.548) (xy 0.787 -0.548) (xy 0.79 -0.549) (xy 0.792 -0.549) (xy 0.795 -0.55) - (xy 0.797 -0.55) (xy 0.8 -0.55) (xy 1.3 -0.55) (xy 1.303 -0.55) (xy 1.305 -0.55) (xy 1.308 -0.549) - (xy 1.31 -0.549) (xy 1.313 -0.548) (xy 1.315 -0.548) (xy 1.318 -0.547) (xy 1.32 -0.546) (xy 1.323 -0.545) - (xy 1.325 -0.543) (xy 1.327 -0.542) (xy 1.329 -0.54) (xy 1.331 -0.539) (xy 1.333 -0.537) (xy 1.335 -0.535) - (xy 1.337 -0.533) (xy 1.339 -0.531) (xy 1.34 -0.529) (xy 1.342 -0.527) (xy 1.343 -0.525) (xy 1.345 -0.523) - (xy 1.346 -0.52) (xy 1.347 -0.518) (xy 1.348 -0.515) (xy 1.348 -0.513) (xy 1.349 -0.51) (xy 1.349 -0.508) - (xy 1.35 -0.505) (xy 1.35 -0.503) (xy 1.35 -0.5) (xy 1.35 -0.3) (xy 1.35 -0.297) (xy 1.35 -0.295) - (xy 1.349 -0.292) (xy 1.349 -0.29) (xy 1.348 -0.287) (xy 1.348 -0.285) (xy 1.347 -0.282) (xy 1.346 -0.28) - (xy 1.345 -0.277) (xy 1.343 -0.275) (xy 1.342 -0.273) (xy 1.34 -0.271) (xy 1.339 -0.269) (xy 1.337 -0.267) - (xy 1.335 -0.265) (xy 1.333 -0.263) (xy 1.331 -0.261) (xy 1.329 -0.26) (xy 1.327 -0.258) (xy 1.325 -0.257) - (xy 1.323 -0.255) (xy 1.32 -0.254) (xy 1.318 -0.253) (xy 1.315 -0.252) (xy 1.313 -0.252) (xy 1.31 -0.251) - (xy 1.308 -0.251) (xy 1.305 -0.25) (xy 1.303 -0.25) (xy 1.3 -0.25) (xy 0.8 -0.25) (xy 0.797 -0.25) - (xy 0.795 -0.25) (xy 0.792 -0.251) (xy 0.79 -0.251) (xy 0.787 -0.252) (xy 0.785 -0.252) (xy 0.782 -0.253) - (xy 0.78 -0.254) (xy 0.777 -0.255) (xy 0.775 -0.257) (xy 0.773 -0.258) (xy 0.771 -0.26) (xy 0.769 -0.261) - (xy 0.767 -0.263) (xy 0.765 -0.265) (xy 0.763 -0.267) (xy 0.761 -0.269) (xy 0.76 -0.271) (xy 0.758 -0.273) - (xy 0.757 -0.275) (xy 0.755 -0.277) (xy 0.754 -0.28) (xy 0.753 -0.282) (xy 0.752 -0.285) (xy 0.752 -0.287) - (xy 0.751 -0.29) (xy 0.751 -0.292) (xy 0.75 -0.295) (xy 0.75 -0.297) (xy 0.75 -0.3) - ) + (fp_line + (start -1.94 2.685) + (end 1.94 2.685) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "39f6ec7e-745d-4a7f-813e-55f5ddf50212") + (layer "F.SilkS") + (uuid "c82ddfe4-0b94-4315-86ad-704649186bcb") ) - (fp_poly - (pts - (xy 0.75 -0.7) (xy 0.75 -0.9) (xy 0.75 -0.903) (xy 0.75 -0.905) (xy 0.751 -0.908) (xy 0.751 -0.91) - (xy 0.752 -0.913) (xy 0.752 -0.915) (xy 0.753 -0.918) (xy 0.754 -0.92) (xy 0.755 -0.923) (xy 0.757 -0.925) - (xy 0.758 -0.927) (xy 0.76 -0.929) (xy 0.761 -0.931) (xy 0.763 -0.933) (xy 0.765 -0.935) (xy 0.767 -0.937) - (xy 0.769 -0.939) (xy 0.771 -0.94) (xy 0.773 -0.942) (xy 0.775 -0.943) (xy 0.777 -0.945) (xy 0.78 -0.946) - (xy 0.782 -0.947) (xy 0.785 -0.948) (xy 0.787 -0.948) (xy 0.79 -0.949) (xy 0.792 -0.949) (xy 0.795 -0.95) - (xy 0.797 -0.95) (xy 0.8 -0.95) (xy 1.3 -0.95) (xy 1.303 -0.95) (xy 1.305 -0.95) (xy 1.308 -0.949) - (xy 1.31 -0.949) (xy 1.313 -0.948) (xy 1.315 -0.948) (xy 1.318 -0.947) (xy 1.32 -0.946) (xy 1.323 -0.945) - (xy 1.325 -0.943) (xy 1.327 -0.942) (xy 1.329 -0.94) (xy 1.331 -0.939) (xy 1.333 -0.937) (xy 1.335 -0.935) - (xy 1.337 -0.933) (xy 1.339 -0.931) (xy 1.34 -0.929) (xy 1.342 -0.927) (xy 1.343 -0.925) (xy 1.345 -0.923) - (xy 1.346 -0.92) (xy 1.347 -0.918) (xy 1.348 -0.915) (xy 1.348 -0.913) (xy 1.349 -0.91) (xy 1.349 -0.908) - (xy 1.35 -0.905) (xy 1.35 -0.903) (xy 1.35 -0.9) (xy 1.35 -0.7) (xy 1.35 -0.697) (xy 1.35 -0.695) - (xy 1.349 -0.692) (xy 1.349 -0.69) (xy 1.348 -0.687) (xy 1.348 -0.685) (xy 1.347 -0.682) (xy 1.346 -0.68) - (xy 1.345 -0.677) (xy 1.343 -0.675) (xy 1.342 -0.673) (xy 1.34 -0.671) (xy 1.339 -0.669) (xy 1.337 -0.667) - (xy 1.335 -0.665) (xy 1.333 -0.663) (xy 1.331 -0.661) (xy 1.329 -0.66) (xy 1.327 -0.658) (xy 1.325 -0.657) - (xy 1.323 -0.655) (xy 1.32 -0.654) (xy 1.318 -0.653) (xy 1.315 -0.652) (xy 1.313 -0.652) (xy 1.31 -0.651) - (xy 1.308 -0.651) (xy 1.305 -0.65) (xy 1.303 -0.65) (xy 1.3 -0.65) (xy 0.8 -0.65) (xy 0.797 -0.65) - (xy 0.795 -0.65) (xy 0.792 -0.651) (xy 0.79 -0.651) (xy 0.787 -0.652) (xy 0.785 -0.652) (xy 0.782 -0.653) - (xy 0.78 -0.654) (xy 0.777 -0.655) (xy 0.775 -0.657) (xy 0.773 -0.658) (xy 0.771 -0.66) (xy 0.769 -0.661) - (xy 0.767 -0.663) (xy 0.765 -0.665) (xy 0.763 -0.667) (xy 0.761 -0.669) (xy 0.76 -0.671) (xy 0.758 -0.673) - (xy 0.757 -0.675) (xy 0.755 -0.677) (xy 0.754 -0.68) (xy 0.753 -0.682) (xy 0.752 -0.685) (xy 0.752 -0.687) - (xy 0.751 -0.69) (xy 0.751 -0.692) (xy 0.75 -0.695) (xy 0.75 -0.697) (xy 0.75 -0.7) - ) + (fp_line + (start 3.11 -1.785) + (end 2.06 -1.785) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "0d4b3c6f-8a1a-4441-b07b-cc1d04ddcc5e") + (layer "F.SilkS") + (uuid "31f465be-ae3d-4680-b7fe-502138f2c088") ) - (fp_poly - (pts - (xy -0.5 0.7) (xy -0.5 -0.7) (xy -0.5 -0.705) (xy -0.499 -0.71) (xy -0.499 -0.716) (xy -0.498 -0.721) - (xy -0.497 -0.726) (xy -0.495 -0.731) (xy -0.493 -0.736) (xy -0.491 -0.741) (xy -0.489 -0.745) (xy -0.487 -0.75) - (xy -0.484 -0.754) (xy -0.481 -0.759) (xy -0.478 -0.763) (xy -0.474 -0.767) (xy -0.471 -0.771) (xy -0.467 -0.774) - (xy -0.463 -0.778) (xy -0.459 -0.781) (xy -0.454 -0.784) (xy -0.45 -0.787) (xy -0.445 -0.789) (xy -0.441 -0.791) - (xy -0.436 -0.793) (xy -0.431 -0.795) (xy -0.426 -0.797) (xy -0.421 -0.798) (xy -0.416 -0.799) (xy -0.41 -0.799) - (xy -0.405 -0.8) (xy -0.4 -0.8) (xy 0.4 -0.8) (xy 0.405 -0.8) (xy 0.41 -0.799) (xy 0.416 -0.799) - (xy 0.421 -0.798) (xy 0.426 -0.797) (xy 0.431 -0.795) (xy 0.436 -0.793) (xy 0.441 -0.791) (xy 0.445 -0.789) - (xy 0.45 -0.787) (xy 0.454 -0.784) (xy 0.459 -0.781) (xy 0.463 -0.778) (xy 0.467 -0.774) (xy 0.471 -0.771) - (xy 0.474 -0.767) (xy 0.478 -0.763) (xy 0.481 -0.759) (xy 0.484 -0.754) (xy 0.487 -0.75) (xy 0.489 -0.745) - (xy 0.491 -0.741) (xy 0.493 -0.736) (xy 0.495 -0.731) (xy 0.497 -0.726) (xy 0.498 -0.721) (xy 0.499 -0.716) - (xy 0.499 -0.71) (xy 0.5 -0.705) (xy 0.5 -0.7) (xy 0.5 0.7) (xy 0.5 0.705) (xy 0.499 0.71) (xy 0.499 0.716) - (xy 0.498 0.721) (xy 0.497 0.726) (xy 0.495 0.731) (xy 0.493 0.736) (xy 0.491 0.741) (xy 0.489 0.745) - (xy 0.487 0.75) (xy 0.484 0.754) (xy 0.481 0.759) (xy 0.478 0.763) (xy 0.474 0.767) (xy 0.471 0.771) - (xy 0.467 0.774) (xy 0.463 0.778) (xy 0.459 0.781) (xy 0.454 0.784) (xy 0.45 0.787) (xy 0.445 0.789) - (xy 0.441 0.791) (xy 0.436 0.793) (xy 0.431 0.795) (xy 0.426 0.797) (xy 0.421 0.798) (xy 0.416 0.799) - (xy 0.41 0.799) (xy 0.405 0.8) (xy 0.4 0.8) (xy -0.4 0.8) (xy -0.405 0.8) (xy -0.41 0.799) (xy -0.416 0.799) - (xy -0.421 0.798) (xy -0.426 0.797) (xy -0.431 0.795) (xy -0.436 0.793) (xy -0.441 0.791) (xy -0.445 0.789) - (xy -0.45 0.787) (xy -0.454 0.784) (xy -0.459 0.781) (xy -0.463 0.778) (xy -0.467 0.774) (xy -0.471 0.771) - (xy -0.474 0.767) (xy -0.478 0.763) (xy -0.481 0.759) (xy -0.484 0.754) (xy -0.487 0.75) (xy -0.489 0.745) - (xy -0.491 0.741) (xy -0.493 0.736) (xy -0.495 0.731) (xy -0.497 0.726) (xy -0.498 0.721) (xy -0.499 0.716) - (xy -0.499 0.71) (xy -0.5 0.705) (xy -0.5 0.7) - ) + (fp_line + (start 3.11 0.715) + (end 3.11 -1.785) (stroke - (width 0.01) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "b3c1629f-8214-474e-ab33-9ceabfec1aa7") + (layer "F.SilkS") + (uuid "d15f7328-6f05-4c82-ab77-36b64a0a2443") ) - (fp_poly - (pts - (xy -1.35 0.9) (xy -1.35 0.7) (xy -1.35 0.697) (xy -1.35 0.695) (xy -1.349 0.692) (xy -1.349 0.69) - (xy -1.348 0.687) (xy -1.348 0.685) (xy -1.347 0.682) (xy -1.346 0.68) (xy -1.345 0.677) (xy -1.343 0.675) - (xy -1.342 0.673) (xy -1.34 0.671) (xy -1.339 0.669) (xy -1.337 0.667) (xy -1.335 0.665) (xy -1.333 0.663) - (xy -1.331 0.661) (xy -1.329 0.66) (xy -1.327 0.658) (xy -1.325 0.657) (xy -1.323 0.655) (xy -1.32 0.654) - (xy -1.318 0.653) (xy -1.315 0.652) (xy -1.313 0.652) (xy -1.31 0.651) (xy -1.308 0.651) (xy -1.305 0.65) - (xy -1.303 0.65) (xy -1.3 0.65) (xy -0.8 0.65) (xy -0.797 0.65) (xy -0.795 0.65) (xy -0.792 0.651) - (xy -0.79 0.651) (xy -0.787 0.652) (xy -0.785 0.652) (xy -0.782 0.653) (xy -0.78 0.654) (xy -0.777 0.655) - (xy -0.775 0.657) (xy -0.773 0.658) (xy -0.771 0.66) (xy -0.769 0.661) (xy -0.767 0.663) (xy -0.765 0.665) - (xy -0.763 0.667) (xy -0.761 0.669) (xy -0.76 0.671) (xy -0.758 0.673) (xy -0.757 0.675) (xy -0.755 0.677) - (xy -0.754 0.68) (xy -0.753 0.682) (xy -0.752 0.685) (xy -0.752 0.687) (xy -0.751 0.69) (xy -0.751 0.692) - (xy -0.75 0.695) (xy -0.75 0.697) (xy -0.75 0.7) (xy -0.75 0.9) (xy -0.75 0.903) (xy -0.75 0.905) - (xy -0.751 0.908) (xy -0.751 0.91) (xy -0.752 0.913) (xy -0.752 0.915) (xy -0.753 0.918) (xy -0.754 0.92) - (xy -0.755 0.923) (xy -0.757 0.925) (xy -0.758 0.927) (xy -0.76 0.929) (xy -0.761 0.931) (xy -0.763 0.933) - (xy -0.765 0.935) (xy -0.767 0.937) (xy -0.769 0.939) (xy -0.771 0.94) (xy -0.773 0.942) (xy -0.775 0.943) - (xy -0.777 0.945) (xy -0.78 0.946) (xy -0.782 0.947) (xy -0.785 0.948) (xy -0.787 0.948) (xy -0.79 0.949) - (xy -0.792 0.949) (xy -0.795 0.95) (xy -0.797 0.95) (xy -0.8 0.95) (xy -1.3 0.95) (xy -1.303 0.95) - (xy -1.305 0.95) (xy -1.308 0.949) (xy -1.31 0.949) (xy -1.313 0.948) (xy -1.315 0.948) (xy -1.318 0.947) - (xy -1.32 0.946) (xy -1.323 0.945) (xy -1.325 0.943) (xy -1.327 0.942) (xy -1.329 0.94) (xy -1.331 0.939) - (xy -1.333 0.937) (xy -1.335 0.935) (xy -1.337 0.933) (xy -1.339 0.931) (xy -1.34 0.929) (xy -1.342 0.927) - (xy -1.343 0.925) (xy -1.345 0.923) (xy -1.346 0.92) (xy -1.347 0.918) (xy -1.348 0.915) (xy -1.348 0.913) - (xy -1.349 0.91) (xy -1.349 0.908) (xy -1.35 0.905) (xy -1.35 0.903) (xy -1.35 0.9) - ) + (fp_line + (start -3.9 0.47) + (end -3.5 0.47) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "6b57b875-ad20-4995-9e9e-07c17aab43d2") + (layer "F.CrtYd") + (uuid "58f1a9b0-4ec8-4f0b-958e-6c101230197d") ) - (fp_poly - (pts - (xy -1.35 0.5) (xy -1.35 0.3) (xy -1.35 0.297) (xy -1.35 0.295) (xy -1.349 0.292) (xy -1.349 0.29) - (xy -1.348 0.287) (xy -1.348 0.285) (xy -1.347 0.282) (xy -1.346 0.28) (xy -1.345 0.277) (xy -1.343 0.275) - (xy -1.342 0.273) (xy -1.34 0.271) (xy -1.339 0.269) (xy -1.337 0.267) (xy -1.335 0.265) (xy -1.333 0.263) - (xy -1.331 0.261) (xy -1.329 0.26) (xy -1.327 0.258) (xy -1.325 0.257) (xy -1.323 0.255) (xy -1.32 0.254) - (xy -1.318 0.253) (xy -1.315 0.252) (xy -1.313 0.252) (xy -1.31 0.251) (xy -1.308 0.251) (xy -1.305 0.25) - (xy -1.303 0.25) (xy -1.3 0.25) (xy -0.8 0.25) (xy -0.797 0.25) (xy -0.795 0.25) (xy -0.792 0.251) - (xy -0.79 0.251) (xy -0.787 0.252) (xy -0.785 0.252) (xy -0.782 0.253) (xy -0.78 0.254) (xy -0.777 0.255) - (xy -0.775 0.257) (xy -0.773 0.258) (xy -0.771 0.26) (xy -0.769 0.261) (xy -0.767 0.263) (xy -0.765 0.265) - (xy -0.763 0.267) (xy -0.761 0.269) (xy -0.76 0.271) (xy -0.758 0.273) (xy -0.757 0.275) (xy -0.755 0.277) - (xy -0.754 0.28) (xy -0.753 0.282) (xy -0.752 0.285) (xy -0.752 0.287) (xy -0.751 0.29) (xy -0.751 0.292) - (xy -0.75 0.295) (xy -0.75 0.297) (xy -0.75 0.3) (xy -0.75 0.5) (xy -0.75 0.503) (xy -0.75 0.505) - (xy -0.751 0.508) (xy -0.751 0.51) (xy -0.752 0.513) (xy -0.752 0.515) (xy -0.753 0.518) (xy -0.754 0.52) - (xy -0.755 0.523) (xy -0.757 0.525) (xy -0.758 0.527) (xy -0.76 0.529) (xy -0.761 0.531) (xy -0.763 0.533) - (xy -0.765 0.535) (xy -0.767 0.537) (xy -0.769 0.539) (xy -0.771 0.54) (xy -0.773 0.542) (xy -0.775 0.543) - (xy -0.777 0.545) (xy -0.78 0.546) (xy -0.782 0.547) (xy -0.785 0.548) (xy -0.787 0.548) (xy -0.79 0.549) - (xy -0.792 0.549) (xy -0.795 0.55) (xy -0.797 0.55) (xy -0.8 0.55) (xy -1.3 0.55) (xy -1.303 0.55) - (xy -1.305 0.55) (xy -1.308 0.549) (xy -1.31 0.549) (xy -1.313 0.548) (xy -1.315 0.548) (xy -1.318 0.547) - (xy -1.32 0.546) (xy -1.323 0.545) (xy -1.325 0.543) (xy -1.327 0.542) (xy -1.329 0.54) (xy -1.331 0.539) - (xy -1.333 0.537) (xy -1.335 0.535) (xy -1.337 0.533) (xy -1.339 0.531) (xy -1.34 0.529) (xy -1.342 0.527) - (xy -1.343 0.525) (xy -1.345 0.523) (xy -1.346 0.52) (xy -1.347 0.518) (xy -1.348 0.515) (xy -1.348 0.513) - (xy -1.349 0.51) (xy -1.349 0.508) (xy -1.35 0.505) (xy -1.35 0.503) (xy -1.35 0.5) + (fp_line + (start -3.9 3.28) + (end -3.9 0.47) + (stroke + (width 0.05) + (type solid) ) + (layer "F.CrtYd") + (uuid "e3015e82-05cc-427b-b1cd-e1b0d70caea9") + ) + (fp_line + (start -3.5 -2.18) + (end -2.3 -2.18) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "dc0c89bb-44ae-42b0-bda4-e4340db9a047") + (layer "F.CrtYd") + (uuid "16888ce5-e134-468c-87e4-95a4a57abaf0") ) - (fp_poly - (pts - (xy -1.35 0.1) (xy -1.35 -0.1) (xy -1.35 -0.103) (xy -1.35 -0.105) (xy -1.349 -0.108) (xy -1.349 -0.11) - (xy -1.348 -0.113) (xy -1.348 -0.115) (xy -1.347 -0.118) (xy -1.346 -0.12) (xy -1.345 -0.123) (xy -1.343 -0.125) - (xy -1.342 -0.127) (xy -1.34 -0.129) (xy -1.339 -0.131) (xy -1.337 -0.133) (xy -1.335 -0.135) (xy -1.333 -0.137) - (xy -1.331 -0.139) (xy -1.329 -0.14) (xy -1.327 -0.142) (xy -1.325 -0.143) (xy -1.323 -0.145) (xy -1.32 -0.146) - (xy -1.318 -0.147) (xy -1.315 -0.148) (xy -1.313 -0.148) (xy -1.31 -0.149) (xy -1.308 -0.149) (xy -1.305 -0.15) - (xy -1.303 -0.15) (xy -1.3 -0.15) (xy -0.8 -0.15) (xy -0.797 -0.15) (xy -0.795 -0.15) (xy -0.792 -0.149) - (xy -0.79 -0.149) (xy -0.787 -0.148) (xy -0.785 -0.148) (xy -0.782 -0.147) (xy -0.78 -0.146) (xy -0.777 -0.145) - (xy -0.775 -0.143) (xy -0.773 -0.142) (xy -0.771 -0.14) (xy -0.769 -0.139) (xy -0.767 -0.137) (xy -0.765 -0.135) - (xy -0.763 -0.133) (xy -0.761 -0.131) (xy -0.76 -0.129) (xy -0.758 -0.127) (xy -0.757 -0.125) (xy -0.755 -0.123) - (xy -0.754 -0.12) (xy -0.753 -0.118) (xy -0.752 -0.115) (xy -0.752 -0.113) (xy -0.751 -0.11) (xy -0.751 -0.108) - (xy -0.75 -0.105) (xy -0.75 -0.103) (xy -0.75 -0.1) (xy -0.75 0.1) (xy -0.75 0.103) (xy -0.75 0.105) - (xy -0.751 0.108) (xy -0.751 0.11) (xy -0.752 0.113) (xy -0.752 0.115) (xy -0.753 0.118) (xy -0.754 0.12) - (xy -0.755 0.123) (xy -0.757 0.125) (xy -0.758 0.127) (xy -0.76 0.129) (xy -0.761 0.131) (xy -0.763 0.133) - (xy -0.765 0.135) (xy -0.767 0.137) (xy -0.769 0.139) (xy -0.771 0.14) (xy -0.773 0.142) (xy -0.775 0.143) - (xy -0.777 0.145) (xy -0.78 0.146) (xy -0.782 0.147) (xy -0.785 0.148) (xy -0.787 0.148) (xy -0.79 0.149) - (xy -0.792 0.149) (xy -0.795 0.15) (xy -0.797 0.15) (xy -0.8 0.15) (xy -1.3 0.15) (xy -1.303 0.15) - (xy -1.305 0.15) (xy -1.308 0.149) (xy -1.31 0.149) (xy -1.313 0.148) (xy -1.315 0.148) (xy -1.318 0.147) - (xy -1.32 0.146) (xy -1.323 0.145) (xy -1.325 0.143) (xy -1.327 0.142) (xy -1.329 0.14) (xy -1.331 0.139) - (xy -1.333 0.137) (xy -1.335 0.135) (xy -1.337 0.133) (xy -1.339 0.131) (xy -1.34 0.129) (xy -1.342 0.127) - (xy -1.343 0.125) (xy -1.345 0.123) (xy -1.346 0.12) (xy -1.347 0.118) (xy -1.348 0.115) (xy -1.348 0.113) - (xy -1.349 0.11) (xy -1.349 0.108) (xy -1.35 0.105) (xy -1.35 0.103) (xy -1.35 0.1) + (fp_line + (start -3.5 0.47) + (end -3.5 -2.18) + (stroke + (width 0.05) + (type solid) ) + (layer "F.CrtYd") + (uuid "bd85030a-3888-44e2-ad84-793f1fca3561") + ) + (fp_line + (start -2.3 -3.28) + (end 2.3 -3.28) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "8b59ab75-fa70-4411-867f-781f5aebd7f8") + (layer "F.CrtYd") + (uuid "ba52edd6-7aad-4d6e-be8c-fa6b8a5fca75") ) - (fp_poly - (pts - (xy -1.35 -0.3) (xy -1.35 -0.5) (xy -1.35 -0.503) (xy -1.35 -0.505) (xy -1.349 -0.508) (xy -1.349 -0.51) - (xy -1.348 -0.513) (xy -1.348 -0.515) (xy -1.347 -0.518) (xy -1.346 -0.52) (xy -1.345 -0.523) (xy -1.343 -0.525) - (xy -1.342 -0.527) (xy -1.34 -0.529) (xy -1.339 -0.531) (xy -1.337 -0.533) (xy -1.335 -0.535) (xy -1.333 -0.537) - (xy -1.331 -0.539) (xy -1.329 -0.54) (xy -1.327 -0.542) (xy -1.325 -0.543) (xy -1.323 -0.545) (xy -1.32 -0.546) - (xy -1.318 -0.547) (xy -1.315 -0.548) (xy -1.313 -0.548) (xy -1.31 -0.549) (xy -1.308 -0.549) (xy -1.305 -0.55) - (xy -1.303 -0.55) (xy -1.3 -0.55) (xy -0.8 -0.55) (xy -0.797 -0.55) (xy -0.795 -0.55) (xy -0.792 -0.549) - (xy -0.79 -0.549) (xy -0.787 -0.548) (xy -0.785 -0.548) (xy -0.782 -0.547) (xy -0.78 -0.546) (xy -0.777 -0.545) - (xy -0.775 -0.543) (xy -0.773 -0.542) (xy -0.771 -0.54) (xy -0.769 -0.539) (xy -0.767 -0.537) (xy -0.765 -0.535) - (xy -0.763 -0.533) (xy -0.761 -0.531) (xy -0.76 -0.529) (xy -0.758 -0.527) (xy -0.757 -0.525) (xy -0.755 -0.523) - (xy -0.754 -0.52) (xy -0.753 -0.518) (xy -0.752 -0.515) (xy -0.752 -0.513) (xy -0.751 -0.51) (xy -0.751 -0.508) - (xy -0.75 -0.505) (xy -0.75 -0.503) (xy -0.75 -0.5) (xy -0.75 -0.3) (xy -0.75 -0.297) (xy -0.75 -0.295) - (xy -0.751 -0.292) (xy -0.751 -0.29) (xy -0.752 -0.287) (xy -0.752 -0.285) (xy -0.753 -0.282) (xy -0.754 -0.28) - (xy -0.755 -0.277) (xy -0.757 -0.275) (xy -0.758 -0.273) (xy -0.76 -0.271) (xy -0.761 -0.269) (xy -0.763 -0.267) - (xy -0.765 -0.265) (xy -0.767 -0.263) (xy -0.769 -0.261) (xy -0.771 -0.26) (xy -0.773 -0.258) (xy -0.775 -0.257) - (xy -0.777 -0.255) (xy -0.78 -0.254) (xy -0.782 -0.253) (xy -0.785 -0.252) (xy -0.787 -0.252) (xy -0.79 -0.251) - (xy -0.792 -0.251) (xy -0.795 -0.25) (xy -0.797 -0.25) (xy -0.8 -0.25) (xy -1.3 -0.25) (xy -1.303 -0.25) - (xy -1.305 -0.25) (xy -1.308 -0.251) (xy -1.31 -0.251) (xy -1.313 -0.252) (xy -1.315 -0.252) (xy -1.318 -0.253) - (xy -1.32 -0.254) (xy -1.323 -0.255) (xy -1.325 -0.257) (xy -1.327 -0.258) (xy -1.329 -0.26) (xy -1.331 -0.261) - (xy -1.333 -0.263) (xy -1.335 -0.265) (xy -1.337 -0.267) (xy -1.339 -0.269) (xy -1.34 -0.271) (xy -1.342 -0.273) - (xy -1.343 -0.275) (xy -1.345 -0.277) (xy -1.346 -0.28) (xy -1.347 -0.282) (xy -1.348 -0.285) (xy -1.348 -0.287) - (xy -1.349 -0.29) (xy -1.349 -0.292) (xy -1.35 -0.295) (xy -1.35 -0.297) (xy -1.35 -0.3) + (fp_line + (start -2.3 -2.18) + (end -2.3 -3.28) + (stroke + (width 0.05) + (type solid) ) + (layer "F.CrtYd") + (uuid "d724f36e-4a2c-48e4-9b88-63a9b9c7d086") + ) + (fp_line + (start -1.69 3.08) + (end -1.69 3.28) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "492cd4e8-411d-4ee3-8e92-40abeadc6364") + (layer "F.CrtYd") + (uuid "ccea39c6-92fa-4285-a1d6-4d8f72e114ec") ) - (fp_poly - (pts - (xy -1.35 -0.7) (xy -1.35 -0.9) (xy -1.35 -0.903) (xy -1.35 -0.905) (xy -1.349 -0.908) (xy -1.349 -0.91) - (xy -1.348 -0.913) (xy -1.348 -0.915) (xy -1.347 -0.918) (xy -1.346 -0.92) (xy -1.345 -0.923) (xy -1.343 -0.925) - (xy -1.342 -0.927) (xy -1.34 -0.929) (xy -1.339 -0.931) (xy -1.337 -0.933) (xy -1.335 -0.935) (xy -1.333 -0.937) - (xy -1.331 -0.939) (xy -1.329 -0.94) (xy -1.327 -0.942) (xy -1.325 -0.943) (xy -1.323 -0.945) (xy -1.32 -0.946) - (xy -1.318 -0.947) (xy -1.315 -0.948) (xy -1.313 -0.948) (xy -1.31 -0.949) (xy -1.308 -0.949) (xy -1.305 -0.95) - (xy -1.303 -0.95) (xy -1.3 -0.95) (xy -0.8 -0.95) (xy -0.797 -0.95) (xy -0.795 -0.95) (xy -0.792 -0.949) - (xy -0.79 -0.949) (xy -0.787 -0.948) (xy -0.785 -0.948) (xy -0.782 -0.947) (xy -0.78 -0.946) (xy -0.777 -0.945) - (xy -0.775 -0.943) (xy -0.773 -0.942) (xy -0.771 -0.94) (xy -0.769 -0.939) (xy -0.767 -0.937) (xy -0.765 -0.935) - (xy -0.763 -0.933) (xy -0.761 -0.931) (xy -0.76 -0.929) (xy -0.758 -0.927) (xy -0.757 -0.925) (xy -0.755 -0.923) - (xy -0.754 -0.92) (xy -0.753 -0.918) (xy -0.752 -0.915) (xy -0.752 -0.913) (xy -0.751 -0.91) (xy -0.751 -0.908) - (xy -0.75 -0.905) (xy -0.75 -0.903) (xy -0.75 -0.9) (xy -0.75 -0.7) (xy -0.75 -0.697) (xy -0.75 -0.695) - (xy -0.751 -0.692) (xy -0.751 -0.69) (xy -0.752 -0.687) (xy -0.752 -0.685) (xy -0.753 -0.682) (xy -0.754 -0.68) - (xy -0.755 -0.677) (xy -0.757 -0.675) (xy -0.758 -0.673) (xy -0.76 -0.671) (xy -0.761 -0.669) (xy -0.763 -0.667) - (xy -0.765 -0.665) (xy -0.767 -0.663) (xy -0.769 -0.661) (xy -0.771 -0.66) (xy -0.773 -0.658) (xy -0.775 -0.657) - (xy -0.777 -0.655) (xy -0.78 -0.654) (xy -0.782 -0.653) (xy -0.785 -0.652) (xy -0.787 -0.652) (xy -0.79 -0.651) - (xy -0.792 -0.651) (xy -0.795 -0.65) (xy -0.797 -0.65) (xy -0.8 -0.65) (xy -1.3 -0.65) (xy -1.303 -0.65) - (xy -1.305 -0.65) (xy -1.308 -0.651) (xy -1.31 -0.651) (xy -1.313 -0.652) (xy -1.315 -0.652) (xy -1.318 -0.653) - (xy -1.32 -0.654) (xy -1.323 -0.655) (xy -1.325 -0.657) (xy -1.327 -0.658) (xy -1.329 -0.66) (xy -1.331 -0.661) - (xy -1.333 -0.663) (xy -1.335 -0.665) (xy -1.337 -0.667) (xy -1.339 -0.669) (xy -1.34 -0.671) (xy -1.342 -0.673) - (xy -1.343 -0.675) (xy -1.345 -0.677) (xy -1.346 -0.68) (xy -1.347 -0.682) (xy -1.348 -0.685) (xy -1.348 -0.687) - (xy -1.349 -0.69) (xy -1.349 -0.692) (xy -1.35 -0.695) (xy -1.35 -0.697) (xy -1.35 -0.7) + (fp_line + (start -1.69 3.28) + (end -3.9 3.28) + (stroke + (width 0.05) + (type solid) ) + (layer "F.CrtYd") + (uuid "0f9fa9f5-32bf-4ab4-ad5c-b72734113b61") + ) + (fp_line + (start 1.69 3.08) + (end -1.69 3.08) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Mask") - (uuid "8c38b70d-879c-4b02-b859-60efa28f9653") + (layer "F.CrtYd") + (uuid "e757cfb5-3aaa-46d0-999f-970aad907cb7") ) - (fp_circle - (center -1.95 -0.8) - (end -1.85 -0.8) + (fp_line + (start 1.69 3.28) + (end 1.69 3.08) (stroke - (width 0.2) + (width 0.05) (type solid) ) - (fill no) - (layer "F.SilkS") - (uuid "32d8b003-0bb6-4bec-976b-3329bfea2685") + (layer "F.CrtYd") + (uuid "b8505b31-9026-43d5-858f-63abc71dc7aa") ) - (fp_poly - (pts - (xy -0.425 0.64) (xy -0.425 -0.64) (xy -0.425 -0.643) (xy -0.425 -0.645) (xy -0.424 -0.648) (xy -0.424 -0.65) - (xy -0.423 -0.653) (xy -0.423 -0.655) (xy -0.422 -0.658) (xy -0.421 -0.66) (xy -0.42 -0.663) (xy -0.418 -0.665) - (xy -0.417 -0.667) (xy -0.415 -0.669) (xy -0.414 -0.671) (xy -0.412 -0.673) (xy -0.41 -0.675) (xy -0.408 -0.677) - (xy -0.406 -0.679) (xy -0.404 -0.68) (xy -0.402 -0.682) (xy -0.4 -0.683) (xy -0.398 -0.685) (xy -0.395 -0.686) - (xy -0.393 -0.687) (xy -0.39 -0.688) (xy -0.388 -0.688) (xy -0.385 -0.689) (xy -0.383 -0.689) (xy -0.38 -0.69) - (xy -0.378 -0.69) (xy -0.375 -0.69) (xy 0.375 -0.69) (xy 0.378 -0.69) (xy 0.38 -0.69) (xy 0.383 -0.689) - (xy 0.385 -0.689) (xy 0.388 -0.688) (xy 0.39 -0.688) (xy 0.393 -0.687) (xy 0.395 -0.686) (xy 0.398 -0.685) - (xy 0.4 -0.683) (xy 0.402 -0.682) (xy 0.404 -0.68) (xy 0.406 -0.679) (xy 0.408 -0.677) (xy 0.41 -0.675) - (xy 0.412 -0.673) (xy 0.414 -0.671) (xy 0.415 -0.669) (xy 0.417 -0.667) (xy 0.418 -0.665) (xy 0.42 -0.663) - (xy 0.421 -0.66) (xy 0.422 -0.658) (xy 0.423 -0.655) (xy 0.423 -0.653) (xy 0.424 -0.65) (xy 0.424 -0.648) - (xy 0.425 -0.645) (xy 0.425 -0.643) (xy 0.425 -0.64) (xy 0.425 0.64) (xy 0.425 0.643) (xy 0.425 0.645) - (xy 0.424 0.648) (xy 0.424 0.65) (xy 0.423 0.653) (xy 0.423 0.655) (xy 0.422 0.658) (xy 0.421 0.66) - (xy 0.42 0.663) (xy 0.418 0.665) (xy 0.417 0.667) (xy 0.415 0.669) (xy 0.414 0.671) (xy 0.412 0.673) - (xy 0.41 0.675) (xy 0.408 0.677) (xy 0.406 0.679) (xy 0.404 0.68) (xy 0.402 0.682) (xy 0.4 0.683) - (xy 0.398 0.685) (xy 0.395 0.686) (xy 0.393 0.687) (xy 0.39 0.688) (xy 0.388 0.688) (xy 0.385 0.689) - (xy 0.383 0.689) (xy 0.38 0.69) (xy 0.378 0.69) (xy 0.375 0.69) (xy -0.375 0.69) (xy -0.378 0.69) - (xy -0.38 0.69) (xy -0.383 0.689) (xy -0.385 0.689) (xy -0.388 0.688) (xy -0.39 0.688) (xy -0.393 0.687) - (xy -0.395 0.686) (xy -0.398 0.685) (xy -0.4 0.683) (xy -0.402 0.682) (xy -0.404 0.68) (xy -0.406 0.679) - (xy -0.408 0.677) (xy -0.41 0.675) (xy -0.412 0.673) (xy -0.414 0.671) (xy -0.415 0.669) (xy -0.417 0.667) - (xy -0.418 0.665) (xy -0.42 0.663) (xy -0.421 0.66) (xy -0.422 0.658) (xy -0.423 0.655) (xy -0.423 0.653) - (xy -0.424 0.65) (xy -0.424 0.648) (xy -0.425 0.645) (xy -0.425 0.643) (xy -0.425 0.64) + (fp_line + (start 2.3 -3.28) + (end 2.3 -2.18) + (stroke + (width 0.05) + (type solid) ) + (layer "F.CrtYd") + (uuid "3a80e4a2-3f91-4dba-9650-1bc33f7fed3c") + ) + (fp_line + (start 2.3 -2.18) + (end 3.5 -2.18) (stroke - (width 0.01) + (width 0.05) (type solid) ) - (fill yes) - (layer "F.Paste") - (uuid "c5e6763e-4462-4a71-a535-3e33db48aadb") + (layer "F.CrtYd") + (uuid "816acf32-590a-4715-afc4-085629c0fcfd") ) (fp_line - (start 1.55 1.25) - (end 1.55 -1.25) + (start 3.5 -2.18) + (end 3.5 0.47) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "6669dc51-3647-4c1f-a440-174ad91e28fe") + (uuid "e9abab59-7e2c-4116-9914-f1b7f90e43aa") ) (fp_line - (start 1.55 -1.25) - (end -1.55 -1.25) + (start 3.5 0.47) + (end 3.9 0.47) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "cac4d44d-f864-4ec4-b7b3-2f2b6a13ef17") + (uuid "73c66dbb-42a3-4ad1-9dd0-5da8ad8f31a6") ) (fp_line - (start -1.55 1.25) - (end 1.55 1.25) + (start 3.9 0.47) + (end 3.9 3.28) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "09a7127a-325e-4eb3-84df-0a0fdb36fc39") + (uuid "8b797c5c-f28f-49eb-8c32-5db6a1a39286") ) (fp_line - (start -1.55 -1.25) - (end -1.55 1.25) + (start 3.9 3.28) + (end 1.69 3.28) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "b76e27f0-a148-4c4b-af8d-a2f3968589fb") + (uuid "e785d391-0e0e-45eb-8ec9-1890c07f2191") ) (fp_line - (start 1.1 1) - (end -1.1 1) + (start -3 -1.675) + (end -3 2.575) (stroke - (width 0.127) + (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "d94bbe63-5806-4b23-95f9-71c4d4303cb5") + (uuid "ebf9050d-8606-4a1b-be50-e70ab17a2501") ) (fp_line - (start 1.1 -1) - (end 1.1 1) + (start -3 -1.675) + (end 3 -1.675) (stroke - (width 0.127) + (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "56b98458-a4fa-48e7-8521-42426e36a0e9") + (uuid "9df93fb5-f6d3-47bd-b871-b6a8b0fbd792") ) (fp_line - (start -1.1 1) - (end -1.1 -1) + (start -3 2.575) + (end 3 2.575) (stroke - (width 0.127) + (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "bc635484-2fa6-4a12-af71-410867095caf") + (uuid "7bcc57ad-cc5b-4eec-94e2-d2bceae5dfa2") ) (fp_line - (start -1.1 -1) - (end 1.1 -1) + (start -2 -1.675) + (end -1.5 -0.967893) (stroke - (width 0.127) + (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "67b4f308-c3f2-4ef4-a86d-20b9cdd22876") + (uuid "fd55e7fc-5a3a-4702-a99b-e20519755339") ) - (fp_circle - (center -1.95 -0.8) - (end -1.85 -0.8) + (fp_line + (start -1.5 -0.967893) + (end -1 -1.675) (stroke - (width 0.2) + (width 0.1) (type solid) ) - (fill no) (layer "F.Fab") - (uuid "256e5e24-7029-4479-a578-9de2f6c1283b") - ) - (pad "1" smd roundrect - (at -1.05 -0.8 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "VSYS") - (pinfunction "SYS_1") - (pintype "output") - (uuid "b69ba64e-8bf7-4b6e-9baa-7ad824e1d524") + (uuid "86cc30d7-fc2d-4c1f-94b9-23b62976ced3") ) - (pad "2" smd roundrect - (at -1.05 -0.4 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "VBAT") - (pinfunction "BAT_2") - (pintype "output") - (uuid "85ad80bf-1981-4f7b-b4bc-586035c9da0a") + (fp_line + (start 3 -1.675) + (end 3 2.575) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "9eb95cac-0a57-4f38-8e94-46195b4a153a") ) - (pad "3" smd roundrect - (at -1.05 0 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "/MCU_Core/STAT2") - (pinfunction "STAT2_3") - (pintype "output") - (uuid "0c7baddb-0a16-4cc0-809e-737780172ae0") - ) - (pad "4" smd roundrect - (at -1.05 0.4 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "GND") - (pinfunction "~{CE}_4") - (pintype "input") - (uuid "362f73ec-8e08-4edb-b2d5-10d77226bd7a") + (fp_text user "${REFERENCE}" + (at 0 0 0) + (layer "F.Fab") + (uuid "5ced2e15-bdf3-4035-8457-96a8851c3a83") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) ) - (pad "5" smd roundrect - (at -1.05 0.8 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) + (pad "1" smd roundrect + (at -1.5 -2) + (size 0.6 1.55) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) (net "GND") - (pinfunction "GND_5") + (pinfunction "GND_1") (pintype "power_in") - (uuid "c86059fb-33ac-4f4f-89c7-fe36b350c269") - ) - (pad "6" smd roundrect - (at 1.05 0.8 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "/Power_Charger/CHG_TS") - (pinfunction "TS/MR_6") - (pintype "input") - (uuid "2e8a88c8-ed5a-4a85-a885-43baf4f7eeb8") - ) - (pad "7" smd roundrect - (at 1.05 0.4 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "/Power_Charger/CHG_VSET") - (pinfunction "ILIM/VSET_7") - (pintype "input") - (uuid "1c14ca36-eeec-4a61-976d-5a082b670417") + (uuid "f8f99ad6-3f07-4db2-aef5-022bad5f7352") ) - (pad "8" smd roundrect - (at 1.05 0 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "/Power_Charger/CHG_ISET") - (pinfunction "ISET_8") - (pintype "input") - (uuid "12967c0f-f661-4a91-9cc7-27774fa6c9cc") + (pad "2" smd roundrect + (at -0.5 -2) + (size 0.6 1.55) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "3V3") + (pinfunction "VCC_2") + (pintype "power_in") + (uuid "d4470de2-29e2-4454-9424-f1c4180fd11d") ) - (pad "9" smd roundrect - (at 1.05 -0.4 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "/MCU_Core/STAT1") - (pinfunction "STAT1_9") - (pintype "output") - (uuid "a0ffce4d-3bae-481b-aa81-7cac89e665e0") + (pad "3" smd roundrect + (at 0.5 -2) + (size 0.6 1.55) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/Accelerometer/I2C_SDA") + (pinfunction "SDA_3") + (pintype "bidirectional") + (uuid "d1799902-4d1b-434c-a867-be3d16e32b0a") ) - (pad "10" smd roundrect - (at 1.05 -0.8 180) - (size 0.5 0.2) - (layers "F.Cu" "F.Paste") - (roundrect_rratio 0.26) - (net "VBUS") - (pinfunction "IN_10") + (pad "4" smd roundrect + (at 1.5 -2) + (size 0.6 1.55) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/Accelerometer/I2C_SCL") + (pinfunction "SCL_4") (pintype "input") - (uuid "65840fb0-9e19-4b51-9ce7-4ed7a0b40a82") - ) - (pad "11" smd custom - (at 0 0 180) - (size 0.5 0.5) - (layers "F.Cu") - (net "GND") - (pinfunction "THERMAL_PAD_11") - (pintype "passive") - (options - (clearance outline) - (anchor rect) - ) - (primitives - (gr_poly - (pts - (xy -0.45 0.7) (xy -0.45 -0.7) (xy -0.45 -0.703) (xy -0.45 -0.705) (xy -0.449 -0.708) (xy -0.449 -0.71) - (xy -0.448 -0.713) (xy -0.448 -0.715) (xy -0.447 -0.718) (xy -0.446 -0.72) (xy -0.445 -0.723) - (xy -0.443 -0.725) (xy -0.442 -0.727) (xy -0.44 -0.729) (xy -0.439 -0.731) (xy -0.437 -0.733) - (xy -0.435 -0.735) (xy -0.433 -0.737) (xy -0.431 -0.739) (xy -0.429 -0.74) (xy -0.427 -0.742) - (xy -0.425 -0.743) (xy -0.423 -0.745) (xy -0.42 -0.746) (xy -0.418 -0.747) (xy -0.415 -0.748) - (xy -0.413 -0.748) (xy -0.41 -0.749) (xy -0.408 -0.749) (xy -0.405 -0.75) (xy -0.403 -0.75) (xy -0.4 -0.75) - (xy 0.4 -0.75) (xy 0.403 -0.75) (xy 0.405 -0.75) (xy 0.408 -0.749) (xy 0.41 -0.749) (xy 0.413 -0.748) - (xy 0.415 -0.748) (xy 0.418 -0.747) (xy 0.42 -0.746) (xy 0.423 -0.745) (xy 0.425 -0.743) (xy 0.427 -0.742) - (xy 0.429 -0.74) (xy 0.431 -0.739) (xy 0.433 -0.737) (xy 0.435 -0.735) (xy 0.437 -0.733) (xy 0.439 -0.731) - (xy 0.44 -0.729) (xy 0.442 -0.727) (xy 0.443 -0.725) (xy 0.445 -0.723) (xy 0.446 -0.72) (xy 0.447 -0.718) - (xy 0.448 -0.715) (xy 0.448 -0.713) (xy 0.449 -0.71) (xy 0.449 -0.708) (xy 0.45 -0.705) (xy 0.45 -0.703) - (xy 0.45 -0.7) (xy 0.45 0.7) (xy 0.45 0.703) (xy 0.45 0.705) (xy 0.449 0.708) (xy 0.449 0.71) - (xy 0.448 0.713) (xy 0.448 0.715) (xy 0.447 0.718) (xy 0.446 0.72) (xy 0.445 0.723) (xy 0.443 0.725) - (xy 0.442 0.727) (xy 0.44 0.729) (xy 0.439 0.731) (xy 0.437 0.733) (xy 0.435 0.735) (xy 0.433 0.737) - (xy 0.431 0.739) (xy 0.429 0.74) (xy 0.427 0.742) (xy 0.425 0.743) (xy 0.423 0.745) (xy 0.42 0.746) - (xy 0.418 0.747) (xy 0.415 0.748) (xy 0.413 0.748) (xy 0.41 0.749) (xy 0.408 0.749) (xy 0.405 0.75) - (xy 0.403 0.75) (xy 0.4 0.75) (xy -0.4 0.75) (xy -0.403 0.75) (xy -0.405 0.75) (xy -0.408 0.749) - (xy -0.41 0.749) (xy -0.413 0.748) (xy -0.415 0.748) (xy -0.418 0.747) (xy -0.42 0.746) (xy -0.423 0.745) - (xy -0.425 0.743) (xy -0.427 0.742) (xy -0.429 0.74) (xy -0.431 0.739) (xy -0.433 0.737) (xy -0.435 0.735) - (xy -0.437 0.733) (xy -0.439 0.731) (xy -0.44 0.729) (xy -0.442 0.727) (xy -0.443 0.725) (xy -0.445 0.723) - (xy -0.446 0.72) (xy -0.447 0.718) (xy -0.448 0.715) (xy -0.448 0.713) (xy -0.449 0.71) (xy -0.449 0.708) - (xy -0.45 0.705) (xy -0.45 0.703) (xy -0.45 0.7) - ) - (width 0.01) - (fill yes) - ) - ) - (uuid "ff4712ac-a586-4040-9dee-4a8a1f340bb8") + (uuid "6b5fd061-7a08-4dfb-ace6-55e380ad772d") ) - (pad "12" thru_hole circle - (at 0 -0.5 180) - (size 0.3 0.3) - (drill 0.2) - (layers "*.Cu") - (remove_unused_layers no) - (net "GND") - (uuid "a70408f9-f447-446f-ab4f-867071df5d38") + (pad "MP" smd roundrect + (at -2.8 1.875) + (size 1.2 1.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.208333) + (uuid "ede36db9-c1b2-43a1-a3c9-9d336f3f2241") ) - (pad "13" thru_hole circle - (at 0 0.5 180) - (size 0.3 0.3) - (drill 0.2) - (layers "*.Cu") - (remove_unused_layers no) - (net "GND") - (uuid "de4cb4e4-7bab-43fe-ba65-d765b737dbe8") + (pad "MP" smd roundrect + (at 2.8 1.875) + (size 1.2 1.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.208333) + (uuid "27c0a140-d886-4d2d-a031-d8766d2f4c7c") ) (embedded_fonts no) - (model "${KIPRJMOD}/libraries/BQ25185DLHR/BQ25185DLHR.step" + (model "${KICAD10_3DMODEL_DIR}/Connector_JST.3dshapes/JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal.step" (offset (xyz 0 0 0) ) @@ -5483,21 +5167,21 @@ (xyz 1 1 1) ) (rotate - (xyz -90 0 0) + (xyz 0 0 0) ) ) ) - (footprint "Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal" + (footprint "MountingHole:MountingHole_2.2mm_M2_ISO14580" (layer "F.Cu") - (uuid "87312f15-4904-4812-a8ac-fdb6935b1b62") - (at 124.4 108.125) - (descr "JST SH series connector, SM04B-SRSS-TB (http://www.jst-mfg.com/product/pdf/eng/eSH.pdf)") - (tags "connector JST SH horizontal") - (property "Reference" "U_OLED1" - (at 0 -3.98 0) + (uuid "8c4c9864-2b8a-48e3-8b26-bebd78f8bff1") + (at 147 127) + (descr "Mounting Hole 2.2mm, M2, no annular, generated by kicad-footprint-generator mountinghole.py") + (tags "mountinghole M2 ISO14580") + (property "Reference" "MH4" + (at 0 -2.85 0) (layer "F.SilkS") (hide yes) - (uuid "f21dabe4-0ea4-4e61-b82e-82b28a04106e") + (uuid "50d60790-3983-4812-921d-857c546a552e") (effects (font (size 1 1) @@ -5505,10 +5189,10 @@ ) ) ) - (property "Value" "Qwiic connector" - (at 0 3.98 0) + (property "Value" "MountingHole_2.2mm_M2_ISO14580" + (at 0 2.85 0) (layer "F.Fab") - (uuid "b39ff267-ef08-4c6e-a552-2cdcf02d59cc") + (uuid "818dfaef-fa2d-4b42-abf4-9d7ae128eb39") (effects (font (size 1 1) @@ -5520,30 +5204,29 @@ (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "ef9daf8e-5ed6-45a6-9ede-18c6d3b6566e") + (uuid "2e419004-6684-4515-b426-00d559a56cdf") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Generic 4-pin I2C SSD1306 OLED breakout module (VCC, GND, SCL, SDA). Hand-authored project-local symbol, no vendor-specific pinout assumed." + (property "Description" "" (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "656a6174-b20e-4651-9a29-2e8631c93b4f") + (uuid "c6462a4c-284c-4062-9383-de4ae7313eea") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "JST" + (property "KiLib_Generator" "mounting_hardware/mounting_hole" (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (layer "F.SilkS") (hide yes) - (uuid "50ac44ff-b9a7-4ece-9195-37b7e3cb46c0") + (uuid "afc3ae44-5b81-479a-80c6-1c1da3484a4b") (effects (font (size 1 1) @@ -5551,25 +5234,61 @@ ) ) ) - (property "Manufacturer_Part_Number" "SM04B-SRSS-TB(LF)(SN)" + (attr board_only exclude_from_pos_files exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (fp_circle + (center 0 0) + (end 1.9 0) + (stroke + (width 0.15) + (type solid) + ) + (fill no) + (layer "Cmts.User") + (uuid "eb4ad1f8-bfdc-4fdb-8a62-7d8fc481989a") + ) + (fp_circle + (center 0 0) + (end 2.15 0) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "F.CrtYd") + (uuid "26a0779b-ca57-4557-b239-b7256fbd5181") + ) + (fp_text user "${REFERENCE}" (at 0 0 0) - (unlocked yes) (layer "F.Fab") - (hide yes) - (uuid "a8329894-1013-428a-868d-ae2ca82697bf") + (uuid "77789181-6b20-4659-8d0b-1f6a30b6560e") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.95 0.95) + (thickness 0.14) ) ) ) - (property "LCSC" "C160404" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") + (pad "" np_thru_hole circle + (at 0 0) + (size 2.2 2.2) + (drill 2.2) + (layers "*.Cu" "*.Mask") + (uuid "e1b3c078-b7b3-4533-9459-1ff08a06f7f6") + ) + (embedded_fonts no) + ) + (footprint "Fiducial:Fiducial_1mm_Mask2mm" + (layer "F.Cu") + (uuid "8d04ff21-1f58-4349-b854-4309ccdb7ff3") + (at 143.75 61.75) + (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") + (tags "fiducial") + (property "Reference" "FID2" + (at 0 -1.95 0) + (layer "F.SilkS") (hide yes) - (uuid "35423f89-6f6a-4e1f-ac14-27caae246ed1") + (uuid "969e9740-332d-46cc-8cb1-a8bd0358ec56") (effects (font (size 1 1) @@ -5577,408 +5296,63 @@ ) ) ) - (property "Stackup Path" "U_OLED1" - (at 0 2 0) - (layer "F.SilkS") + (property "Value" "Fiducial_1mm_Mask2mm" + (at 0 1.95 0) + (layer "F.Fab") (hide yes) - (uuid "edd50709-92fa-42d6-8191-2d757fe8aa90") + (uuid "f2a6714b-c58e-43b4-a599-f18de9fbdbc5") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:107" - (at 0 2 0) - (layer "F.SilkS") + (property "Datasheet" "" + (at 0 0 0) + (layer "F.Fab") (hide yes) - (uuid "c005a554-d664-4485-860d-d0ff988fd68d") + (uuid "3d3ad3c5-a3c1-4853-81ee-ea034c847155") (effects (font (size 1.27 1.27) - (thickness 0.15) ) ) ) - (path "/873c651e-8375-5f6a-839c-0927d0e7d3c1") - (units - (unit - (name "A") - (pins "2" "1" "4" "3") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -3.11 -1.785) - (end -2.06 -1.785) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "8a8c14b7-7341-4bba-90c7-bf6ca2706aaa") - ) - (fp_line - (start -3.11 0.715) - (end -3.11 -1.785) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "e43be91c-48c8-4187-9b8f-55d03efe785e") - ) - (fp_line - (start -2.06 -1.785) - (end -2.06 -2.775) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "5c49bbc3-38c7-4683-a283-2a5a2587fed5") - ) - (fp_line - (start -1.94 2.685) - (end 1.94 2.685) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "c82ddfe4-0b94-4315-86ad-704649186bcb") - ) - (fp_line - (start 3.11 -1.785) - (end 2.06 -1.785) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "31f465be-ae3d-4680-b7fe-502138f2c088") - ) - (fp_line - (start 3.11 0.715) - (end 3.11 -1.785) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "d15f7328-6f05-4c82-ab77-36b64a0a2443") - ) - (fp_line - (start -3.9 0.47) - (end -3.5 0.47) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "58f1a9b0-4ec8-4f0b-958e-6c101230197d") - ) - (fp_line - (start -3.9 3.28) - (end -3.9 0.47) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "e3015e82-05cc-427b-b1cd-e1b0d70caea9") - ) - (fp_line - (start -3.5 -2.18) - (end -2.3 -2.18) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "16888ce5-e134-468c-87e4-95a4a57abaf0") - ) - (fp_line - (start -3.5 0.47) - (end -3.5 -2.18) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "bd85030a-3888-44e2-ad84-793f1fca3561") - ) - (fp_line - (start -2.3 -3.28) - (end 2.3 -3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "ba52edd6-7aad-4d6e-be8c-fa6b8a5fca75") - ) - (fp_line - (start -2.3 -2.18) - (end -2.3 -3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "d724f36e-4a2c-48e4-9b88-63a9b9c7d086") - ) - (fp_line - (start -1.69 3.08) - (end -1.69 3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "ccea39c6-92fa-4285-a1d6-4d8f72e114ec") - ) - (fp_line - (start -1.69 3.28) - (end -3.9 3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "0f9fa9f5-32bf-4ab4-ad5c-b72734113b61") - ) - (fp_line - (start 1.69 3.08) - (end -1.69 3.08) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "e757cfb5-3aaa-46d0-999f-970aad907cb7") - ) - (fp_line - (start 1.69 3.28) - (end 1.69 3.08) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "b8505b31-9026-43d5-858f-63abc71dc7aa") - ) - (fp_line - (start 2.3 -3.28) - (end 2.3 -2.18) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "3a80e4a2-3f91-4dba-9650-1bc33f7fed3c") - ) - (fp_line - (start 2.3 -2.18) - (end 3.5 -2.18) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "816acf32-590a-4715-afc4-085629c0fcfd") - ) - (fp_line - (start 3.5 -2.18) - (end 3.5 0.47) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "e9abab59-7e2c-4116-9914-f1b7f90e43aa") - ) - (fp_line - (start 3.5 0.47) - (end 3.9 0.47) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "73c66dbb-42a3-4ad1-9dd0-5da8ad8f31a6") - ) - (fp_line - (start 3.9 0.47) - (end 3.9 3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "8b797c5c-f28f-49eb-8c32-5db6a1a39286") - ) - (fp_line - (start 3.9 3.28) - (end 1.69 3.28) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "e785d391-0e0e-45eb-8ec9-1890c07f2191") - ) - (fp_line - (start -3 -1.675) - (end -3 2.575) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "ebf9050d-8606-4a1b-be50-e70ab17a2501") - ) - (fp_line - (start -3 -1.675) - (end 3 -1.675) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "9df93fb5-f6d3-47bd-b871-b6a8b0fbd792") - ) - (fp_line - (start -3 2.575) - (end 3 2.575) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "7bcc57ad-cc5b-4eec-94e2-d2bceae5dfa2") - ) - (fp_line - (start -2 -1.675) - (end -1.5 -0.967893) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "fd55e7fc-5a3a-4702-a99b-e20519755339") - ) - (fp_line - (start -1.5 -0.967893) - (end -1 -1.675) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "86cc30d7-fc2d-4c1f-94b9-23b62976ced3") - ) - (fp_line - (start 3 -1.675) - (end 3 2.575) - (stroke - (width 0.1) - (type solid) - ) - (layer "F.Fab") - (uuid "9eb95cac-0a57-4f38-8e94-46195b4a153a") - ) - (fp_text user "${REFERENCE}" + (property "Description" "" (at 0 0 0) (layer "F.Fab") - (uuid "5ced2e15-bdf3-4035-8457-96a8851c3a83") + (hide yes) + (uuid "ce48043f-a6d9-42e9-803f-f5b79a901cfb") (effects (font - (size 1 1) - (thickness 0.15) + (size 1.27 1.27) ) ) ) - (pad "1" smd roundrect - (at -1.5 -2) - (size 0.6 1.55) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "GND") - (pinfunction "GND_1") - (pintype "power_in") - (uuid "f8f99ad6-3f07-4db2-aef5-022bad5f7352") - ) - (pad "2" smd roundrect - (at -0.5 -2) - (size 0.6 1.55) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "3V3") - (pinfunction "VCC_2") - (pintype "power_in") - (uuid "d4470de2-29e2-4454-9424-f1c4180fd11d") - ) - (pad "3" smd roundrect - (at 0.5 -2) - (size 0.6 1.55) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Accelerometer/I2C_SDA") - (pinfunction "SDA_3") - (pintype "bidirectional") - (uuid "d1799902-4d1b-434c-a867-be3d16e32b0a") - ) - (pad "4" smd roundrect - (at 1.5 -2) - (size 0.6 1.55) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Accelerometer/I2C_SCL") - (pinfunction "SCL_4") - (pintype "input") - (uuid "6b5fd061-7a08-4dfb-ace6-55e380ad772d") - ) - (pad "MP" smd roundrect - (at -2.8 1.875) - (size 1.2 1.8) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.208333) - (uuid "ede36db9-c1b2-43a1-a3c9-9d336f3f2241") - ) - (pad "MP" smd roundrect - (at 2.8 1.875) - (size 1.2 1.8) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.208333) - (uuid "27c0a140-d886-4d2d-a031-d8766d2f4c7c") + (attr smd board_only exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (pad "" smd circle + (at 0 0) + (size 1 1) + (layers "F.Cu" "F.Mask") + (solder_mask_margin 0.5) + (clearance 0.6) + (uuid "d339eedb-ec1c-463e-9ace-2a565f955897") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Connector_JST.3dshapes/JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) ) - (footprint "Resistor_SMD:R_0402_1005Metric" + (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "F.Cu") - (uuid "88a25bf2-6956-411c-8c83-7fa8fbc892c3") - (at 134.35 114.515) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_STAT2" - (at 0.09 -1.1 180) + (uuid "95523c4d-0933-4f70-a61c-4aaab9a448d6") + (at 123.4 106.3 180) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_OLED_2" + (at 0 -1.16 0) (layer "F.SilkS") (hide yes) - (uuid "683a2e93-d09d-4016-b8f7-3194e32b4468") + (uuid "d80b4794-dcf9-4ee0-bf7b-351ab8377f15") (effects (font (size 1 1) @@ -5986,10 +5360,10 @@ ) ) ) - (property "Value" "10kΩ" - (at -5.55 -0.505 180) + (property "Value" "100nF" + (at 0 1.16 0) (layer "F.Fab") - (uuid "b7f23e9f-dfe2-46f3-a858-794f643f6058") + (uuid "c3381d27-934b-4484-a096-c132580c9312") (effects (font (size 1 1) @@ -5998,45 +5372,33 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "43acfff5-ddb7-4ba8-a8af-bd63deab5743") + (uuid "cb509595-c87c-487e-b2fd-90eb06a5bb47") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Resistor" - (at 0 0 180) + (property "Description" "Unpolarized capacitor" + (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "56edb9ad-0fbb-4bb4-be7f-d1247b990d83") + (uuid "35bb09b9-dd8a-4af2-b592-77b03feac139") (effects (font (size 1.27 1.27) ) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (property "MF" "Samsung Electro-Mechanics" (at 0 0 180) - (layer "F.SilkS") - (hide yes) - (uuid "83734f2d-5939-47b5-ae35-0f90ee64eadf") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 0) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "918cef0e-119e-4e53-a98c-b9dffc942116") + (uuid "b30e4ee3-f6d0-49cb-acc3-ed449b7897e2") (effects (font (size 1 1) @@ -6044,12 +5406,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "0402WGF1002TCE" - (at 0 0 0) + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" + (at 0 0 180) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "adec6d65-8112-4eff-9f83-dbbdeeca13fe") + (uuid "1ee40a5e-5339-4883-9fae-96ad554da347") (effects (font (size 1 1) @@ -6057,12 +5419,12 @@ ) ) ) - (property "LCSC" "C25744" + (property "LCSC" "C1525" (at 0 0 180) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "c2905452-de99-4b1c-afbb-145d4681dd1e") + (uuid "a30e22fb-6445-40cb-9b66-befc1bbdf56e") (effects (font (size 1 1) @@ -6070,34 +5432,32 @@ ) ) ) - (property "Stackup Path" "R_STAT2" - (at 0 -2 180) + (property "Stackup Path" "C_OLED_2" + (at 0 -2 0) (layer "F.SilkS") (hide yes) - (uuid "2fe23c34-108b-4a40-88df-b2e3ddbab452") + (uuid "e2a8b331-9f3d-4cef-a0fb-d0d654d8ef67") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:67" - (at 0 -2 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:35" + (at 0 -2 0) (layer "F.SilkS") (hide yes) - (uuid "b6ec057f-dcb3-4f12-9fa4-5da68079988a") + (uuid "bbf8fc70-0f5e-42fd-b80b-8c261686142e") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "R_*") - (path "/213051d8-6d7f-5a98-bf06-9f116b171331") + (property ki_fp_filters "C_*") + (path "/2b27245f-94c1-541b-bbeb-0dca2eb4c3cc") (units (unit (name "A") @@ -6107,78 +5467,78 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "98015d6c-3d6f-4f92-a096-7fbdca2d0cfd") + (uuid "46b4b9e7-e1ce-4f37-b916-22d5c7bcba2a") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "32e17da8-8d64-45cf-9260-e8ea52429479") + (uuid "ef956fa7-54e3-432e-9c5b-fff3ecba9c23") ) (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) + (start -0.91 -0.46) + (end 0.91 0.46) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "2ef7dfb0-7daa-4d59-9ea5-3abd1b32c039") + (uuid "c1a2b563-8c3a-4006-a264-be4229488470") ) (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) + (start -0.5 -0.25) + (end 0.5 0.25) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "fa9d0f2a-149e-4f6e-bfc2-f75b19b7b3fe") + (uuid "af350ab5-cd9f-4748-be68-e8142c8c59e0") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 0) (layer "F.Fab") - (uuid "01784e9c-53ce-4916-9359-05e7b4f5b157") + (uuid "5d0fe1cd-01f2-4009-a25f-685f92784c00") (effects (font - (size 0.26 0.26) + (size 0.25 0.25) (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) + (at -0.48 0 180) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/STAT2") + (net "3V3") (pintype "passive") - (uuid "3f416a4d-b988-404c-81d4-7b3c6afe6571") + (uuid "c48f2692-bc53-4d5f-ae73-d1fad227714a") ) (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) + (at 0.48 0 180) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "3V3") + (net "GND") (pintype "passive") - (uuid "effa86dc-4cf9-4806-a45c-774a5b47b31e") + (uuid "5a6c92bf-a917-436c-a490-03ae09ad107c") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -6190,17 +5550,17 @@ ) ) ) - (footprint "MountingHole:MountingHole_2.2mm_M2_ISO14580" + (footprint "ESP32-S3-MINI-1U" (layer "F.Cu") - (uuid "8c4c9864-2b8a-48e3-8b26-bebd78f8bff1") - (at 147 127) - (descr "Mounting Hole 2.2mm, M2, no annular, generated by kicad-footprint-generator mountinghole.py") - (tags "mountinghole M2 ISO14580") - (property "Reference" "MH4" - (at 0 -2.85 0) + (uuid "a1462f61-0aaf-4a59-8170-8f6058d8811a") + (at 136.5 112.5 -90) + (descr "ESP32-S3-MINI-1 and ESP32-S3-MINI-1U") + (tags "esp32-s3") + (property "Reference" "U_MCU1" + (at 0 -9.35 90) (layer "F.SilkS") (hide yes) - (uuid "50d60790-3983-4812-921d-857c546a552e") + (uuid "adefd529-d02b-4307-b2b9-e45cfe9d40d0") (effects (font (size 1 1) @@ -6208,10 +5568,10 @@ ) ) ) - (property "Value" "MountingHole_2.2mm_M2_ISO14580" - (at 0 2.85 0) + (property "Value" "ESP32-S3-MINI-1U-N8" + (at 0 9.35 90) (layer "F.Fab") - (uuid "818dfaef-fa2d-4b42-abf4-9d7ae128eb39") + (uuid "06604fb6-9d5c-4e6b-9833-9df77d5a4f0b") (effects (font (size 1 1) @@ -6220,10 +5580,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "2e419004-6684-4515-b426-00d559a56cdf") + (uuid "8bf0adc7-9876-4ef6-8c87-a06d00e15435") (effects (font (size 1.27 1.27) @@ -6231,586 +5591,817 @@ ) ) (property "Description" "" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "c6462a4c-284c-4062-9383-de4ae7313eea") + (uuid "ecd07101-dd61-4d9b-a0f3-24fb41471f43") (effects (font (size 1.27 1.27) ) ) ) - (property "KiLib_Generator" "mounting_hardware/mounting_hole" - (at 0 0 0) + (property "MF" "Espressif Systems" + (at 0 -2 90) (layer "F.SilkS") (hide yes) - (uuid "afc3ae44-5b81-479a-80c6-1c1da3484a4b") + (uuid "c0074761-9fa8-4fb9-b554-035bb98d2444") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (attr board_only exclude_from_pos_files exclude_from_bom) - (duplicate_pad_numbers_are_jumpers no) - (fp_circle - (center 0 0) - (end 1.9 0) - (stroke - (width 0.15) - (type solid) - ) - (fill no) - (layer "Cmts.User") - (uuid "eb4ad1f8-bfdc-4fdb-8a62-7d8fc481989a") - ) - (fp_circle - (center 0 0) - (end 2.15 0) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "26a0779b-ca57-4557-b239-b7256fbd5181") - ) - (fp_text user "${REFERENCE}" - (at 0 0 0) - (layer "F.Fab") - (uuid "77789181-6b20-4659-8d0b-1f6a30b6560e") - (effects - (font - (size 0.95 0.95) - (thickness 0.14) - ) - ) - ) - (pad "" np_thru_hole circle - (at 0 0) - (size 2.2 2.2) - (drill 2.2) - (layers "*.Cu" "*.Mask") - (uuid "e1b3c078-b7b3-4533-9459-1ff08a06f7f6") - ) - (embedded_fonts no) - ) - (footprint "Fiducial:Fiducial_1mm_Mask2mm" - (layer "F.Cu") - (uuid "8d04ff21-1f58-4349-b854-4309ccdb7ff3") - (at 143.75 61.75) - (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") - (tags "fiducial") - (property "Reference" "FID2" - (at 0 -1.95 0) + (property "Manufacturer_Part_Number" "ESP32-S3-MINI-1U-N8" + (at 0 -2 90) (layer "F.SilkS") (hide yes) - (uuid "969e9740-332d-46cc-8cb1-a8bd0358ec56") + (uuid "620e5202-0f96-426b-985a-2b3fff824d97") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (property "Value" "Fiducial_1mm_Mask2mm" - (at 0 1.95 0) - (layer "F.Fab") + (property "LCSC" "C2980299" + (at 0 -2 90) + (layer "F.SilkS") (hide yes) - (uuid "f2a6714b-c58e-43b4-a599-f18de9fbdbc5") + (uuid "51404b87-6090-4ae1-8527-b4c83c7c230a") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (property "Datasheet" "" - (at 0 0 0) - (layer "F.Fab") + (property "Stackup Path" "U_MCU1" + (at 0 -2 90) + (layer "F.SilkS") (hide yes) - (uuid "3d3ad3c5-a3c1-4853-81ee-ea034c847155") + (uuid "a6daa18d-ad6a-4745-b968-492622c5eafa") (effects (font (size 1.27 1.27) + (thickness 0.15) ) + (justify mirror) ) ) - (property "Description" "" - (at 0 0 0) - (layer "F.Fab") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:97" + (at 0 -2 90) + (layer "F.SilkS") (hide yes) - (uuid "ce48043f-a6d9-42e9-803f-f5b79a901cfb") + (uuid "a27b55a0-1524-45f7-b7ed-31e064199158") (effects (font (size 1.27 1.27) + (thickness 0.15) ) + (justify mirror) ) ) - (attr smd board_only exclude_from_bom) + (path "/0466cd2a-b9be-59f2-b3ed-6d30cbef7aef") + (attr smd) (duplicate_pad_numbers_are_jumpers no) - (pad "" smd circle - (at 0 0) - (size 1 1) - (layers "F.Cu" "F.Mask") - (solder_mask_margin 0.5) - (clearance 0.6) - (uuid "d339eedb-ec1c-463e-9ace-2a565f955897") + (fp_line + (start -7.85 7.85) + (end -7.85 6.8) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "0de2b748-c226-453d-bb57-26fb439c3662") ) - (embedded_fonts no) - ) - (footprint "R2Builders:R2Builders" - (layer "F.Cu") - (uuid "9d267c25-cdf3-4271-ba57-016038d61e0a") - (at 143 118.6) - (property "Reference" "LOGO3" - (at 0 0 0) + (fp_line + (start -6.8 7.85) + (end -7.85 7.85) + (stroke + (width 0.12) + (type solid) + ) (layer "F.SilkS") - (hide yes) - (uuid "874436e1-0bb9-4e9c-8680-a1abb4864743") - (effects - (font - (size 1.5 1.5) - (thickness 0.3) - ) + (uuid "7b0ebdb0-7fa9-4e2b-aa88-d91fb7845d80") + ) + (fp_line + (start 6.8 7.85) + (end 7.85 7.85) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "851b5135-e43c-4592-b523-598a67ba42a3") ) - (property "Value" "LOGO" - (at 0.75 0 0) + (fp_line + (start 7.85 7.85) + (end 7.85 6.8) + (stroke + (width 0.12) + (type solid) + ) (layer "F.SilkS") - (hide yes) - (uuid "8df50e68-cf6d-4b3b-a531-6193ce9df95f") - (effects - (font - (size 1.5 1.5) - (thickness 0.3) - ) + (uuid "cac30b6d-b408-4cbb-a640-f1851da8d88d") + ) + (fp_line + (start -7.7 7.7) + (end -7.7 -7.7) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "ddde090a-9096-4cfa-acca-44ad42b41b51") ) - (property "Datasheet" "" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "f3b6ca63-3676-4551-827c-d45bab9f7218") - (effects - (font - (size 1.27 1.27) - ) + (fp_line + (start 7.7 7.7) + (end -7.7 7.7) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "5048ab39-6397-45c9-990d-e3f892beee35") ) - (property "Description" "" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "d68ed663-7efa-4ec4-85fb-d7f5ea8a209d") - (effects - (font - (size 1.27 1.27) - ) + (fp_line + (start -7.7 -7.7) + (end 7.7 -7.7) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "fa1cb4a1-5a06-4e2b-9b75-2429d75c7dd8") ) - (property "Stackup Path" "" - (at 0 2 0) + (fp_line + (start 7.7 -7.7) + (end 7.7 7.7) + (stroke + (width 0.12) + (type solid) + ) (layer "F.SilkS") - (hide yes) - (uuid "f16e7be7-953e-488e-b076-e08cfe558222") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (uuid "8a5e89ef-a807-462d-8e4b-a79bce60637a") + ) + (fp_line + (start -6.8 -7.85) + (end -8 -7.85) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "d7320027-b700-41e0-8a54-14b2b4e32ac8") ) - (property "Stackup Source" "" - (at 0 2 0) + (fp_line + (start 6.8 -7.85) + (end 7.85 -7.85) + (stroke + (width 0.12) + (type solid) + ) (layer "F.SilkS") - (hide yes) - (uuid "a8c13f84-09a1-4a0d-b13e-54f6b7c15af1") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (uuid "65bc6909-5b98-40a4-991e-e536b6f02927") + ) + (fp_line + (start 7.85 -7.85) + (end 7.85 -6.8) + (stroke + (width 0.12) + (type solid) ) + (layer "F.SilkS") + (uuid "e18eca63-e3ed-4814-b15b-088649d4d842") ) - (attr board_only exclude_from_pos_files exclude_from_bom) - (duplicate_pad_numbers_are_jumpers no) - (fp_poly - (pts - (xy 0.247393 -1.665948) (xy 0.377249 -1.625613) (xy 0.503787 -1.552522) (xy 0.631778 -1.44773) (xy 0.762235 -1.310101) - (xy 0.856872 -1.164927) (xy 0.914145 -1.031604) (xy 0.934678 -0.965416) (xy 0.936621 -0.919549) - (xy 0.91921 -0.871586) (xy 0.907935 -0.849252) (xy 0.854988 -0.77626) (xy 0.789963 -0.727273) (xy 0.722577 -0.704834) - (xy 0.66255 -0.711485) (xy 0.619599 -0.749769) (xy 0.610311 -0.771388) (xy 0.545684 -0.919999) (xy 0.452861 -1.055293) - (xy 0.339428 -1.170639) (xy 0.212971 -1.259408) (xy 0.081075 -1.314968) (xy -0.030093 -1.331133) - (xy -0.128328 -1.321254) (xy -0.201366 -1.287947) (xy -0.252132 -1.226573) (xy -0.28355 -1.132491) - (xy -0.298544 -1.001059) (xy -0.300874 -0.901423) (xy -0.297968 -0.800173) (xy -0.287387 -0.70605) - (xy -0.266562 -0.609797) (xy -0.23292 -0.502158) (xy -0.183891 -0.373876) (xy -0.116906 -0.215694) - (xy -0.099256 -0.175396) (xy 0.000503 0.053719) (xy 0.081048 0.24381) (xy 0.142149 0.394303) (xy 0.183578 0.504626) - (xy 0.205107 0.574206) (xy 0.208386 0.595407) (xy 0.192742 0.667678) (xy 0.151945 0.735516) (xy 0.095199 0.792035) - (xy 0.031709 0.830347) (xy -0.029322 0.843568) (xy -0.07869 0.824811) (xy -0.086702 0.81618) (xy -0.10691 0.779497) - (xy -0.135055 0.715158) (xy -0.156513 0.65989) (xy -0.181133 0.597283) (xy -0.220584 0.501941) (xy -0.270821 0.383414) - (xy -0.327803 0.251253) (xy -0.380337 0.131205) (xy -0.462861 -0.061124) (xy -0.525761 -0.221367) - (xy -0.57142 -0.358182) (xy -0.60222 -0.480228) (xy -0.620542 -0.596164) (xy -0.62877 -0.714647) - (xy -0.629836 -0.775662) (xy -0.618254 -0.977876) (xy -0.57956 -1.149791) (xy -0.510454 -1.300825) - (xy -0.407636 -1.440395) (xy -0.390051 -1.459896) (xy -0.258505 -1.57469) (xy -0.113301 -1.646256) - (xy 0.050743 -1.676889) (xy 0.102951 -1.678444) + (fp_line + (start -8 8) + (end 8 8) + (stroke + (width 0.12) + (type solid) ) + (layer "F.CrtYd") + (uuid "72d41a88-5c0f-4475-933e-3ba244595895") + ) + (fp_line + (start 8 8) + (end 8 -8) (stroke - (width 0) + (width 0.12) (type solid) ) - (fill yes) - (layer "F.SilkS") - (uuid "be607aa7-edde-4c00-8df5-3c0824506a99") + (layer "F.CrtYd") + (uuid "e834baa6-5cb2-495f-98b6-c1640609270e") + ) + (fp_line + (start -8 -8) + (end -8 8) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.CrtYd") + (uuid "f3680912-14bf-432d-9a49-a8d7650f039e") + ) + (fp_line + (start 8 -8) + (end -8 -8) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.CrtYd") + (uuid "d18c35e5-fded-431f-9709-4cacb23e59d8") + ) + (fp_line + (start -7.7 7.7) + (end 7.7 7.7) + (stroke + (width 0.15) + (type solid) + ) + (layer "F.Fab") + (uuid "9335fa15-33fb-4f35-930b-33c34aa87503") + ) + (fp_line + (start 7.7 7.7) + (end 7.7 -7.7) + (stroke + (width 0.15) + (type solid) + ) + (layer "F.Fab") + (uuid "11a6df5d-0cb6-43f4-8624-b3a5ab042be9") + ) + (fp_line + (start -7.7 -7.7) + (end -7.7 7.7) + (stroke + (width 0.15) + (type solid) + ) + (layer "F.Fab") + (uuid "9e6a0764-00e5-4cb0-873e-d11877b5a320") + ) + (fp_line + (start 7.7 -7.7) + (end -7.7 -7.7) + (stroke + (width 0.15) + (type solid) + ) + (layer "F.Fab") + (uuid "f8b19854-2b1a-4631-9495-d4214737c24e") + ) + (fp_text user "${REFERENCE}" + (at 0 0 90) + (layer "F.Fab") + (uuid "70856042-0e16-43ee-b0b6-ba79ff87fe33") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (pad "1" smd rect + (at -7 -5.95) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "e843e8da-5dac-4ec6-a438-7e780234d399") + ) + (pad "2" smd rect + (at -7 -5.1) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "cc3073d5-8564-4aef-98d4-7b4eaad02a6c") + ) + (pad "3" smd rect + (at -7 -4.25) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "3V3") + (uuid "72998f7b-a4b3-45db-bc60-a72bb2958e32") + ) + (pad "4" smd rect + (at -7 -3.4) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/MCU_BOOT") + (uuid "2183d60b-eba7-4a99-afb9-e0a06b0333da") + ) + (pad "5" smd rect + (at -7 -2.55) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "ebc4d25d-ffdf-451b-bd96-9c0ccc9b296b") + ) + (pad "6" smd rect + (at -7 -1.7) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "96f783a1-b3ed-4eb6-892a-1cc77b4a67fd") + ) + (pad "7" smd rect + (at -7 -0.85) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (uuid "875768b4-6053-4494-8588-1ade1ee79bbe") + ) + (pad "8" smd rect + (at -7 0) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO3") + (uuid "0742a455-fac3-4f58-88b7-ec271ca722b6") + ) + (pad "9" smd rect + (at -7 0.85) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "6781f03d-fea7-49bc-9cf9-1606073243a7") + ) + (pad "10" smd rect + (at -7 1.7) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/STICK_Y") + (uuid "b78b309a-2cf3-4a6d-b3d8-5a513f7812b9") + ) + (pad "11" smd rect + (at -7 2.55) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/STICK_X") + (uuid "08fe379b-46da-47c9-a27b-121c14b56b51") + ) + (pad "12" smd rect + (at -7 3.4) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "70c9d873-6daa-41af-9351-21f16eb6a4c8") + ) + (pad "13" smd rect + (at -7 4.25) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "ac80e6f3-d0a7-4154-b335-88049d41ba3a") + ) + (pad "14" smd rect + (at -7 5.1) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/VSYS_SENSE") + (uuid "0922fb8a-ca6b-4a2c-93c4-4b7cf6303687") + ) + (pad "15" smd rect + (at -7 5.95) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO4") + (uuid "5483946b-b35d-48d1-bbdf-e9e93e090a4f") + ) + (pad "16" smd rect + (at -5.95 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Accelerometer/I2C_SDA") + (uuid "b6b25e94-67e3-400e-957b-a09096f6deec") + ) + (pad "17" smd rect + (at -5.1 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Accelerometer/I2C_SCL") + (uuid "94ab7ea5-4bbb-4288-96e3-4ba2c22b94b2") + ) + (pad "18" smd rect + (at -4.25 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/STAT2") + (uuid "7f3be823-256b-4ce3-8f5f-14ece2504ff1") + ) + (pad "19" smd rect + (at -3.4 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/STAT1") + (uuid "541524e3-c7c8-4185-a9d0-ccf153100f48") + ) + (pad "20" smd rect + (at -2.55 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "87a94b8b-136d-4e57-87b5-3c933a92f149") + ) + (pad "21" smd rect + (at -1.7 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/BTN_STICK") + (uuid "2b89fbef-2982-43d5-b93d-5b900867b2c3") + ) + (pad "22" smd rect + (at -0.85 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "3cab05af-7524-43b7-8804-295e04074ece") + ) + (pad "23" smd rect + (at 0 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/USB_DM_MCU") + (uuid "0d36e8cb-6bb8-48e1-afe2-6ef76c04bf66") + ) + (pad "24" smd rect + (at 0.85 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/USB_DP_MCU") + (uuid "36a563e9-789f-4b55-9cf9-e925f64483d5") + ) + (pad "25" smd rect + (at 1.7 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "ab726e7b-25d1-4a61-8f85-44a55ff7d1a4") + ) + (pad "26" smd rect + (at 2.55 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (uuid "bf01c9b5-4976-4d5f-9b5a-44c019f3b085") + ) + (pad "27" smd rect + (at 3.4 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "dd4b331e-3270-4928-9adf-9eb173f64c1e") + ) + (pad "28" smd rect + (at 4.25 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "a1d4df6e-5c40-42fe-a521-08078a6d74ed") + ) + (pad "29" smd rect + (at 5.1 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_CTS") + (uuid "5affc323-8787-4458-ab5e-5f0041fa123c") + ) + (pad "30" smd rect + (at 5.95 7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/RGB_DIN") + (uuid "602ae552-9d7e-45be-9465-efab9b1fc74b") + ) + (pad "31" smd rect + (at 7 5.95) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_DIN") + (uuid "0e0b1b9e-c80d-4b61-8bbb-d37185e5669a") + ) + (pad "32" smd rect + (at 7 5.1) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_DOUT") + (uuid "28e3452b-7c2d-4622-993a-46843e4bd926") + ) + (pad "33" smd rect + (at 7 4.25) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "ACCEL_INT1") + (uuid "c8eb7b57-2ed7-4455-a983-659091dab4e4") + ) + (pad "34" smd rect + (at 7 3.4) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "672d62e2-ce0d-4667-8e11-5d96b524f841") + ) + (pad "35" smd rect + (at 7 2.55) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_RTS") + (uuid "4d3c5bde-b6d8-431d-a192-8edf5e843e7e") + ) + (pad "36" smd rect + (at 7 1.7) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "2516f103-f0ac-4439-afa6-8318175ad81c") + ) + (pad "37" smd rect + (at 7 0.85) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "0d9c210f-81e6-4def-ae83-eb3223e4c8a5") + ) + (pad "38" smd rect + (at 7 0) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/XBee/XBEE_RESET") + (uuid "058f594b-a9c1-4900-8375-c0b6f857f603") + ) + (pad "39" smd rect + (at 7 -0.85) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (uuid "90ae7dee-af06-4415-a4df-02f7fd6c7c57") + ) + (pad "40" smd rect + (at 7 -1.7) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/PWR_HOLD") + (uuid "44c91ce2-6d63-421d-a44d-b3e40a2f1405") + ) + (pad "41" smd rect + (at 7 -2.55) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (uuid "2a49cb74-1aca-4828-b2ab-d582d39a3792") + ) + (pad "42" smd rect + (at 7 -3.4) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "d1c5522b-19c0-4216-9981-d3b61d64e363") + ) + (pad "43" smd rect + (at 7 -4.25) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "ca681aef-3af2-4145-ba8a-a7f80475bbc1") + ) + (pad "44" smd rect + (at 7 -5.1) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (uuid "abae1542-9baf-4cbb-9cb9-80a4998c0b37") + ) + (pad "45" smd rect + (at 7 -5.95) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/MCU_Core/MCU_EN") + (uuid "1f8d77b3-ea34-4fcc-a1ee-edddec463873") + ) + (pad "46" smd rect + (at 5.95 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "603a0674-e9d6-4e56-a302-6c08ea51b98b") + ) + (pad "47" smd rect + (at 5.1 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "a064a03d-191d-47c3-b58d-07b927058b15") + ) + (pad "48" smd rect + (at 4.25 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "992d6a45-2061-4263-ac8e-0017426ffb23") + ) + (pad "49" smd rect + (at 3.4 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "2da0da0b-1e6e-4b1e-8bd1-d448b3a4106a") + ) + (pad "50" smd rect + (at 2.55 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "0b301d77-7a6a-4785-b0a1-5ba167acf3b4") + ) + (pad "51" smd rect + (at 1.7 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "a544ad19-3e55-4b50-b05a-b43e65abe9c6") + ) + (pad "52" smd rect + (at 0.85 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "e7022781-24d2-4024-8d4a-f324cf25816a") ) - (fp_poly - (pts - (xy 0.798363 -0.381916) (xy 0.801295 -0.380876) (xy 0.823527 -0.368418) (xy 0.838779 -0.344697) - (xy 0.849204 -0.300854) (xy 0.856957 -0.228028) (xy 0.863828 -0.123574) (xy 0.881058 0.073143) (xy 0.910704 0.25765) - (xy 0.956281 0.447424) (xy 1.021282 0.65989) (xy 1.091527 0.856879) (xy 1.164019 1.022306) (xy 1.245927 1.167066) - (xy 1.344417 1.302052) (xy 1.466656 1.438159) (xy 1.61981 1.586282) (xy 1.647295 1.611489) (xy 1.830428 1.782039) - (xy 1.979421 1.929278) (xy 2.097493 2.057261) (xy 2.187861 2.170043) (xy 2.253742 2.27168) (xy 2.298355 2.366227) - (xy 2.324917 2.457738) (xy 2.326914 2.468008) (xy 2.329066 2.595135) (xy 2.288029 2.711736) (xy 2.20598 2.816585) - (xy 2.085095 2.908454) (xy 1.927551 2.986118) (xy 1.735525 3.048349) (xy 1.511192 3.093922) (xy 1.25673 3.121608) - (xy 1.157702 3.126979) (xy 1.016513 3.130877) (xy 0.912551 3.129001) (xy 0.837038 3.120863) (xy 0.78123 3.105986) - (xy 0.69272 3.065751) (xy 0.643176 3.023831) (xy 0.625504 2.97377) (xy 0.625159 2.964006) (xy 0.646217 2.886648) - (xy 0.701188 2.82022) (xy 0.777767 2.772761) (xy 0.86365 2.752312) (xy 0.934325 2.762011) (xy 1.059909 2.790945) - (xy 1.216615 2.80287) (xy 1.392724 2.798353) (xy 1.576516 2.777961) (xy 1.75627 2.74226) (xy 1.84359 2.718039) - (xy 1.988477 2.673288) (xy 1.96092 2.593712) (xy 1.918047 2.501863) (xy 1.847691 2.397634) (xy 1.747154 2.27785) - (xy 1.613741 2.139334) (xy 1.444754 1.978911) (xy 1.41852 1.954902) (xy 1.269663 1.816864) (xy 1.150845 1.70034) - (xy 1.055928 1.597932) (xy 0.978779 1.502241) (xy 0.91326 1.405869) (xy 0.853238 1.301417) (xy 0.814999 1.227164) - (xy 0.677663 0.905334) (xy 0.582648 0.57364) (xy 0.528208 0.22529) (xy 0.516861 0.069171) (xy 0.511399 -0.048383) - (xy 0.509624 -0.129431) (xy 0.512855 -0.183716) (xy 0.52241 -0.220981) (xy 0.539609 -0.250967) (xy 0.564358 -0.281739) - (xy 0.640781 -0.349907) (xy 0.722531 -0.384868) - ) - (stroke - (width 0) - (type solid) - ) - (fill yes) - (layer "F.SilkS") - (uuid "dcbeac18-5cfe-4cf6-a74c-1529cb0e453c") + (pad "53" smd rect + (at 0 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "96b61021-e413-4f9f-a2e9-be796a6f8c54") ) - (fp_poly - (pts - (xy -1.673439 0.295119) (xy -1.534248 0.337431) (xy -1.35715 0.4018) (xy -1.141504 0.488453) (xy -0.88667 0.597619) - (xy -0.694622 0.683047) (xy -0.557857 0.741846) (xy -0.402436 0.804311) (xy -0.251013 0.861514) - (xy -0.163708 0.892239) (xy -0.058973 0.929938) (xy 0.029798 0.966327) (xy 0.093144 0.997228) (xy 0.121488 1.018241) - (xy 0.12683 1.070422) (xy 0.102327 1.136746) (xy 0.055613 1.204159) (xy -0.00568 1.259601) (xy -0.027316 1.272784) - (xy -0.112517 1.318404) (xy -0.371309 1.231009) (xy -0.490402 1.188268) (xy -0.635012 1.132521) - (xy -0.788679 1.070315) (xy -0.93494 1.008198) (xy -0.96635 0.994368) (xy -1.080918 0.943713) (xy -1.179669 0.900424) - (xy -1.255292 0.867675) (xy -1.300479 0.848643) (xy -1.310009 0.845122) (xy -1.306913 0.863897) - (xy -1.289976 0.910493) (xy -1.283869 0.925418) (xy -1.260803 0.999065) (xy -1.250371 1.068799) - (xy -1.250319 1.072655) (xy -1.250319 1.139597) (xy -1.059298 1.152418) (xy -0.902461 1.17163) (xy -0.750657 1.206074) - (xy -0.611446 1.252543) (xy -0.492385 1.307828) (xy -0.401034 1.36872) (xy -0.344952 1.432011) (xy -0.333184 1.460621) - (xy -0.334557 1.528569) (xy -0.360767 1.609874) (xy -0.403332 1.68657) (xy -0.453769 1.740689) (xy -0.469901 1.750176) - (xy -0.506471 1.759856) (xy -0.54722 1.750769) (xy -0.605084 1.718744) (xy -0.641464 1.694855) (xy -0.787006 1.619459) - (xy -0.956949 1.567731) (xy -1.13358 1.544092) (xy -1.239862 1.545574) (xy -1.307644 1.552259) (xy -1.359176 1.563524) - (xy -1.405951 1.585388) (xy -1.459462 1.623868) (xy -1.531203 1.684982) (xy -1.567729 1.717248) - (xy -1.670431 1.808077) (xy -1.785773 1.909832) (xy -1.893402 2.004564) (xy -1.923082 2.030631) - (xy -2.048385 2.147266) (xy -2.138648 2.246068) (xy -2.192613 2.325322) (xy -2.209022 2.383315) - (xy -2.199945 2.407649) (xy -2.152043 2.444983) (xy -2.078563 2.468771) (xy -1.974572 2.479559) - (xy -1.835137 2.477892) (xy -1.672662 2.465953) (xy -1.540779 2.454689) (xy -1.447558 2.449429) - (xy -1.385742 2.450176) (xy -1.348075 2.456934) (xy -1.33114 2.466088) (xy -1.303147 2.516348) (xy -1.298047 2.59078) - (xy -1.314817 2.673897) (xy -1.349616 2.746119) (xy -1.377524 2.783925) (xy -1.407175 2.808935) - (xy -1.449851 2.825727) (xy -1.516839 2.838875) (xy -1.610099 2.851746) (xy -1.799826 2.871394) - (xy -1.967778 2.878838) (xy -2.107307 2.87414) (xy -2.211766 2.857363) (xy -2.245779 2.845795) (xy -2.368056 2.771817) - (xy -2.451296 2.674747) (xy -2.494557 2.557816) (xy -2.496902 2.424255) (xy -2.45739 2.277296) (xy -2.429246 2.214664) - (xy -2.382469 2.131173) (xy -2.323507 2.046303) (xy -2.247734 1.95495) (xy -2.150525 1.85201) (xy -2.027255 1.732379) - (xy -1.873296 1.590951) (xy -1.823571 1.546314) (xy -1.702867 1.435637) (xy -1.612125 1.346436) - (xy -1.553416 1.280886) (xy -1.528815 1.241159) (xy -1.528168 1.236742) (xy -1.538172 1.194502) - (xy -1.564535 1.125567) (xy -1.601785 1.044083) (xy -1.606009 1.035565) (xy -1.649425 0.94397) (xy -1.687984 0.854403) - (xy -1.713 0.787237) (xy -1.737361 0.717499) (xy -1.764116 0.676498) (xy -1.807158 0.651612) (xy -1.880377 0.630221) - (xy -1.887978 0.628277) (xy -1.957631 0.604718) (xy -2.008634 0.577005) (xy -2.021731 0.564033) - (xy -2.035144 0.503384) (xy -2.015452 0.432198) (xy -1.970097 0.362318) (xy -1.906515 0.305587) - (xy -1.840655 0.275755) (xy -1.775361 0.274636) - ) - (stroke - (width 0) - (type solid) - ) - (fill yes) - (layer "F.SilkS") - (uuid "767c233e-88c4-4cde-b45c-3643340fb744") + (pad "54" smd rect + (at -0.85 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "1ce201bd-32da-4fdf-b92a-04fb0b06fdf7") ) - (fp_poly - (pts - (xy 0.550775 -3.120374) (xy 0.793163 -3.071376) (xy 1.00362 -2.989746) (xy 1.182836 -2.87525) (xy 1.263406 -2.803152) - (xy 1.375653 -2.669144) (xy 1.463026 -2.514071) (xy 1.527635 -2.332204) (xy 1.571588 -2.11781) (xy 1.594444 -1.903473) - (xy 1.609207 -1.697611) (xy 1.882353 -1.574117) (xy 2.009342 -1.513276) (xy 2.135462 -1.446775) - (xy 2.253337 -1.379149) (xy 2.355591 -1.314936) (xy 2.434846 -1.258671) (xy 2.483727 -1.21489) (xy 2.495168 -1.197268) - (xy 2.48167 -1.196284) (xy 2.437348 -1.217293) (xy 2.369747 -1.25636) (xy 2.311861 -1.292834) (xy 2.205961 -1.35934) - (xy 2.100439 -1.421735) (xy 2.003928 -1.475308) (xy 1.925061 -1.515348) (xy 1.872469 -1.537143) - (xy 1.859443 -1.539746) (xy 1.870093 -1.529298) (xy 1.913272 -1.501284) (xy 1.981068 -1.460697) - (xy 2.022903 -1.436578) (xy 2.13043 -1.371687) (xy 2.22992 -1.305095) (xy 2.313937 -1.242462) (xy 2.375042 -1.189449) - (xy 2.405799 -1.151717) (xy 2.408021 -1.143464) (xy 2.39111 -1.142856) (xy 2.347342 -1.164722) (xy 2.30149 -1.194043) - (xy 2.240539 -1.231231) (xy 2.149851 -1.280831) (xy 2.040598 -1.337332) (xy 1.923948 -1.395223) - (xy 1.811073 -1.448992) (xy 1.713142 -1.493127) (xy 1.641327 -1.522117) (xy 1.626718 -1.526984) - (xy 1.589848 -1.532888) (xy 1.586231 -1.513526) (xy 1.588731 -1.506383) (xy 1.61465 -1.479561) (xy 1.671616 -1.439645) - (xy 1.749034 -1.393797) (xy 1.779607 -1.377357) (xy 1.880681 -1.320823) (xy 1.98258 -1.257633) (xy 2.078083 -1.193048) - (xy 2.159974 -1.132333) (xy 2.221035 -1.080749) (xy 2.254046 -1.04356) (xy 2.256892 -1.02934) (xy 2.230699 -1.025584) - (xy 2.184854 -1.051903) (xy 2.183317 -1.053103) (xy 2.12643 -1.08841) (xy 2.082125 -1.099139) (xy 2.061175 -1.083117) - (xy 2.060711 -1.077846) (xy 2.041687 -1.071041) (xy 1.984388 -1.088164) (xy 1.888474 -1.12935) (xy 1.753607 -1.194733) - (xy 1.7134 -1.21506) (xy 1.542533 -1.297527) (xy 1.342353 -1.386876) (xy 1.127757 -1.47698) (xy 0.939893 -1.551323) - (xy 1.806016 -1.551323) (xy 1.817593 -1.539746) (xy 1.82917 -1.551323) (xy 1.817593 -1.5629) (xy 1.806016 -1.551323) - (xy 0.939893 -1.551323) (xy 0.91364 -1.561712) (xy 0.878997 -1.574477) (xy 1.759708 -1.574477) (xy 1.771285 -1.5629) - (xy 1.782862 -1.574477) (xy 1.771285 -1.586054) (xy 1.759708 -1.574477) (xy 0.878997 -1.574477) - (xy 0.816159 -1.597631) (xy 1.7134 -1.597631) (xy 1.724977 -1.586054) (xy 1.736554 -1.597631) (xy 1.724977 -1.609208) - (xy 1.7134 -1.597631) (xy 0.816159 -1.597631) (xy 0.753321 -1.620785) (xy 1.667092 -1.620785) (xy 1.678669 -1.609208) - (xy 1.690246 -1.620785) (xy 1.678669 -1.632362) (xy 1.667092 -1.620785) (xy 0.753321 -1.620785) - (xy 0.714897 -1.634943) (xy 0.592051 -1.676354) (xy 0.439522 -1.72182) (xy 0.272965 -1.765806) (xy 0.099428 -1.806998) - (xy -0.07404 -1.844081) (xy -0.240393 -1.875742) (xy -0.39258 -1.900668) (xy -0.523556 -1.917545) - (xy -0.62627 -1.925059) (xy -0.693676 -1.921897) (xy -0.706646 -1.918412) (xy -0.735789 -1.914662) - (xy -0.738301 -1.924223) (xy -0.72631 -1.954762) (xy -0.70252 -2.016603) (xy -0.675745 -2.086736) - (xy -0.460494 -2.086736) (xy -0.452433 -2.050637) (xy -0.415019 -2.028367) (xy -0.359701 -2.031049) - (xy -0.306047 -2.056429) (xy -0.292313 -2.069098) (xy -0.254049 -2.130481) (xy -0.227031 -2.208048) - (xy -0.217541 -2.280479) (xy -0.221633 -2.309087) (xy -0.251959 -2.34346) (xy -0.301851 -2.347431) - (xy -0.357378 -2.322575) (xy -0.39133 -2.289904) (xy -0.427561 -2.227008) (xy -0.45214 -2.153318) - (xy -0.460494 -2.086736) (xy -0.675745 -2.086736) (xy -0.671541 -2.097747) (xy -0.663483 -2.118934) - (xy -0.611039 -2.25508) (xy -0.570878 -2.353296) (xy -0.539743 -2.419271) (xy -0.514376 -2.458698) - (xy -0.491519 -2.477266) (xy -0.467916 -2.480669) (xy -0.45737 -2.479023) (xy -0.435274 -2.474244) - (xy -0.402186 -2.466807) (xy -0.353038 -2.455534) (xy -0.282761 -2.439248) (xy -0.186285 -2.416771) - (xy -0.058542 -2.386926) (xy 0.105538 -2.348535) (xy 0.250226 -2.314659) (xy 0.347488 -2.284867) - (xy 0.478888 -2.233742) (xy 0.638778 -2.163645) (xy 0.82151 -2.07694) (xy 0.83792 -2.068877) (xy 1.256427 -1.862715) - (xy 1.24236 -1.950136) (xy 1.18961 -2.165157) (xy 1.105133 -2.346906) (xy 0.98747 -2.497157) (xy 0.835167 -2.617681) - (xy 0.646766 -2.710252) (xy 0.605402 -2.725299) (xy 0.534634 -2.747549) (xy 0.466395 -2.762701) - (xy 0.389116 -2.772043) (xy 0.291224 -2.776861) (xy 0.16115 -2.778444) (xy 0.127347 -2.778485) (xy -0.005182 -2.777819) - (xy -0.102318 -2.774872) (xy -0.17497 -2.76822) (xy -0.234047 -2.756436) (xy -0.290454 -2.738096) - (xy -0.342565 -2.717082) (xy -0.432213 -2.676164) (xy -0.517029 -2.632248) (xy -0.568584 -2.601314) - (xy -0.605277 -2.573183) (xy -0.643554 -2.536347) (xy -0.684882 -2.488193) (xy -0.730729 -2.42611) - (xy -0.782561 -2.347484) (xy -0.841848 -2.249704) (xy -0.910057 -2.130157) (xy -0.988655 -1.986231) - (xy -1.07911 -1.815313) (xy -1.18289 -1.61479) (xy -1.301462 -1.382051) (xy -1.436294 -1.114483) - (xy -1.588853 -0.809474) (xy -1.695211 -0.595949) (xy -1.824884 -0.336627) (xy -1.935889 -0.117593) - (xy -2.029125 0.062836) (xy -2.105495 0.206342) (xy -2.1659 0.314607) (xy -2.211241 0.389313) (xy -2.24242 0.432143) - (xy -2.250486 0.440195) (xy -2.325843 0.486521) (xy -2.392349 0.495325) (xy -2.442597 0.466507) - (xy -2.457145 0.442995) (xy -2.464021 0.417767) (xy -2.461698 0.384601) (xy -2.4478 0.336935) (xy -2.41995 0.268206) - (xy -2.375774 0.171849) (xy -2.312895 0.041301) (xy -2.308365 0.032011) (xy -2.134608 -0.324158) - (xy -2.190276 -0.345993) (xy -2.232284 -0.374968) (xy -2.245845 -0.403878) (xy -2.235922 -0.432844) - (xy -2.208264 -0.496817) (xy -2.165964 -0.589443) (xy -2.112113 -0.704368) (xy -2.049803 -0.835238) - (xy -1.982127 -0.975699) (xy -1.912176 -1.119396) (xy -1.843041 -1.259978) (xy -1.777816 -1.391088) - (xy -1.719591 -1.506374) (xy -1.671459 -1.599481) (xy -1.636512 -1.664056) (xy -1.6186 -1.692879) - (xy -1.567003 -1.719548) (xy -1.511699 -1.720012) (xy -1.480372 -1.717519) (xy -1.455164 -1.722603) - (xy -1.430929 -1.741467) (xy -1.402521 -1.780313) (xy -1.364794 -1.845343) (xy -1.312603 -1.942759) - (xy -1.28764 -1.990065) (xy -1.19433 -2.165231) (xy -1.117032 -2.305404) (xy -1.051441 -2.417202) - (xy -0.99325 -2.507244) (xy -0.938153 -2.582149) (xy -0.881844 -2.648536) (xy -0.820017 -2.713023) - (xy -0.812347 -2.720628) (xy -0.616776 -2.882945) (xy -0.399206 -3.005104) (xy -0.158835 -3.087411) - (xy 0.105135 -3.130172) (xy 0.275764 -3.136973) - ) - (stroke - (width 0) - (type solid) - ) - (fill yes) - (layer "F.SilkS") - (uuid "d809c03c-8105-4977-8fc7-0f155e92ce4a") + (pad "55" smd rect + (at -1.7 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "2a9bd6a5-dfde-4c21-bb14-4dea2d104157") ) - (embedded_fonts no) - ) - (footprint "Resistor_SMD:R_0402_1005Metric" - (layer "F.Cu") - (uuid "a4ce15da-b062-4697-8f6c-88071faa9cc9") - (at 133.74 106.725) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_FB2" - (at 0 -1.17 0) - (layer "F.SilkS") - (hide yes) - (uuid "657b7bc4-b526-47be-9364-0d4bd6856dba") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) + (pad "56" smd rect + (at -2.55 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "28126a98-ae2b-45df-92f3-0174a79092bc") ) - (property "Value" "56.2kΩ" - (at 0 1.17 0) - (layer "F.Fab") - (uuid "aac1a616-6278-4b71-97eb-21182b6aeb57") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) + (pad "57" smd rect + (at -3.4 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "96008beb-ef88-48d6-a945-0fb9cba5b94a") ) - (property "Datasheet" "" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "d54b317e-51c3-4da8-bebe-8f8abee204ff") - (effects - (font - (size 1.27 1.27) - ) - ) + (pad "58" smd rect + (at -4.25 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "a0369a69-2db3-42af-aaa9-6e82bdb2dc6a") ) - (property "Description" "Resistor" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "fdb2d46c-014b-4f70-87cd-25a35ca20c0a") - (effects - (font - (size 1.27 1.27) - ) - ) + (pad "59" smd rect + (at -5.1 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "94a2375f-3d47-48cb-8878-a961c5b7e1c5") ) - (property "MF" "Yageo" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "411c0b8e-0750-49af-bd77-3338b0c7f631") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) + (pad "60" smd rect + (at -5.95 -7 270) + (size 0.4 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "73d06731-2a67-4144-af27-921486ae5342") ) - (property "Manufacturer_Part_Number" "RC0402FR-0756K2L" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "eaf70b90-dfb1-4adb-9a58-5b698a6fd7cb") - (effects - (font - (size 1 1) - (thickness 0.15) - ) + (pad "61" smd custom + (at -1.65 -1.65 270) + (size 0.6 0.6) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (options + (clearance outline) + (anchor rect) ) - ) - (property "LCSC" "C183355" - (at 0 0 180) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "b93defc4-a0e3-4f40-a6b2-a9179885ef39") - (effects - (font - (size 1 1) - (thickness 0.15) + (primitives + (gr_poly + (pts + (xy 0.6 0.6) (xy -0.6 0.6) (xy -0.6 0) (xy 0 -0.6) (xy 0.6 -0.6) + ) + (width 0) + (fill yes) ) ) + (uuid "14e79963-a6f0-4dce-8a05-e524d29522bd") ) - (property "Stackup Path" "R_FB2" - (at 2 0 90) - (layer "F.SilkS") - (hide yes) - (uuid "88efd99b-935a-4ae5-bfe2-17dface683bc") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) + (pad "61" smd rect + (at -1.65 0 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "b70cb84f-4b80-444a-b2dd-465c321861dd") ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:58" - (at 2 0 90) - (layer "F.SilkS") - (hide yes) - (uuid "302c5a6d-e7eb-47cc-92a7-a0b453221a4c") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) + (pad "61" smd rect + (at -1.65 1.65 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "427c5a35-3541-4ee8-a3b8-cdcd7502c32a") ) - (property ki_fp_filters "R_*") - (path "/31d3531d-3c70-537f-859f-5b6468e07c16") - (units - (unit - (name "A") - (pins "1" "2") - ) + (pad "61" smd rect + (at 0 -1.65 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "b1ced44f-5c11-46f4-9012-ec6849671f89") ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "4f6c69c9-6045-4f06-96df-0d96af307b7e") + (pad "61" smd rect + (at 0 0 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "410720d9-00fe-4c5b-bd23-f822058fbb7b") ) - (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "d275a0a7-fe19-4c3e-8cb9-3a6798a6a33e") + (pad "61" smd rect + (at 0 1.65 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "ea28afe4-d42c-4940-9dc7-334d477dc844") ) - (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "f8d236ee-67bb-4b95-96e6-9e8bcf560895") + (pad "61" smd rect + (at 1.65 -1.65 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "e2c2b17e-de4a-452a-920f-d07b4179158d") ) - (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "F.Fab") - (uuid "0accf6b2-8e85-4434-ba83-edc0b8bc808c") + (pad "61" smd rect + (at 1.65 0 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "1610306e-dfbe-47f1-af93-e569096d5a0e") ) - (fp_text user "${REFERENCE}" - (at 0 0 0) - (layer "F.Fab") - (uuid "cdf62203-c9fe-42ce-a43b-c843c3be93f5") - (effects - (font - (size 0.26 0.26) - (thickness 0.04) - ) - ) + (pad "61" smd rect + (at 1.65 1.65 270) + (size 1.2 1.2) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (zone_connect 2) + (uuid "28856794-5770-421c-80c7-bbfecad69e6e") ) - (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) + (pad "62" smd rect + (at -7 -7 90) + (size 0.8 0.8) (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Power_Buck/BUCK_FB") - (pintype "passive") - (uuid "d959f9cc-2458-497a-ac23-1d2aa59eff99") + (net "GND") + (uuid "090fbd80-f761-4ccc-8970-34c46b61a9f0") ) - (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) + (pad "63" smd rect + (at -7 7 90) + (size 0.8 0.8) (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "e6b47b47-bd89-4639-9955-f08d4cd3b63c") + (uuid "8089f91a-cb83-4021-b2d1-767fdd7b79a5") + ) + (pad "64" smd rect + (at 7 7 90) + (size 0.8 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "7f1c1c38-b8a3-4ace-8296-6bdf21cbc376") + ) + (pad "65" smd rect + (at 7 -7 90) + (size 0.8 0.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "f0291fbe-8f63-4a9b-818a-d723334b083d") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KIPRJMOD}/libraries/3dmodels/ESP32-S3-MINI-1U.step" (offset - (xyz 0 0 0) + (xyz -7.7 -7.7 0) ) (scale (xyz 1 1 1) @@ -6926,7 +6517,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:85" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:88" (at -2 0 0) (layer "F.SilkS") (hide yes) @@ -7375,7 +6966,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:48" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:50" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -7707,279 +7298,69 @@ (size 0.6 1.45) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "GND") - (pinfunction "GND_B12") - (pintype "passive") - (uuid "9ce5244b-7662-4ccc-828c-1145c81c913e") - ) - (pad "SH" thru_hole oval - (at -4.32 -3.13) - (size 1 2.1) - (drill oval 0.6 1.7) - (property pad_prop_mechanical) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "SHIELD_SH") - (pintype "passive") - (uuid "57cefecf-2448-45e4-985e-3178debf0e84") - ) - (pad "SH" thru_hole oval - (at -4.32 1.05) - (size 1 1.6) - (drill oval 0.6 1.2) - (property pad_prop_mechanical) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "SHIELD_SH") - (pintype "passive") - (uuid "15d379f9-3703-4f9f-aa6c-631170b81857") - ) - (pad "SH" thru_hole oval - (at 4.32 -3.13) - (size 1 2.1) - (drill oval 0.6 1.7) - (property pad_prop_mechanical) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "SHIELD_SH") - (pintype "passive") - (uuid "16f7985b-903c-4f8f-84d0-bd4c85a63661") - ) - (pad "SH" thru_hole oval - (at 4.32 1.05) - (size 1 1.6) - (drill oval 0.6 1.2) - (property pad_prop_mechanical) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "SHIELD_SH") - (pintype "passive") - (uuid "54c491e6-1186-429c-9562-112dfbe29e7c") - ) - (embedded_fonts no) - (model "${KIPRJMOD}/libraries/3dmodels/USB_C_Receptacle_HRO_TYPE-C-31-M-12.step" - (offset - (xyz 0 -1.05 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 180) - ) - ) - ) - (footprint "Resistor_SMD:R_0402_1005Metric" - (layer "F.Cu") - (uuid "b611f9d7-d56c-4eb1-818b-431aae6bb97d") - (at 122.26 115.5 180) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_VSET1" - (at 0 -1.17 180) - (layer "F.SilkS") - (hide yes) - (uuid "788fa6c2-8508-4acf-b5c7-6c254230d563") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Value" "18kΩ" - (at 0 1.17 180) - (layer "F.Fab") - (uuid "7e793424-fb67-4346-b4a3-298fb9739d26") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Datasheet" "" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "7be390f6-0de0-437a-adb8-0f4706085985") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "Description" "Resistor" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "c214e183-718d-473a-b8b4-a48e4d7171a6") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "MF" "Yageo" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "abdfede7-c5df-484b-b4a9-89be27dbf551") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Manufacturer_Part_Number" "RC0402FR-0718KL" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "3a5e1a67-1cc8-4390-92cf-25c266317159") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "LCSC" "C138044" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "eba6b239-6c3f-446a-9ff0-b5fe86b3c25d") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Stackup Path" "R_VSET1" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "9dad4451-51f8-446f-87ff-437d8849c86d") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:69" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "723c59b0-8588-4b69-a946-e825eddd2d13") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property ki_fp_filters "R_*") - (path "/b59483be-69ee-57e4-ae87-bfff111ed616") - (units - (unit - (name "A") - (pins "1" "2") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "ee1c1b33-865f-4024-9606-dbaa5b1627e9") - ) - (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "5251846c-946e-4205-b5f2-4d5e6582c7b5") - ) - (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "ba51f0a8-5f56-42ab-86df-42647b3f3a72") - ) - (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "F.Fab") - (uuid "e87be81b-2d46-4c4b-aa22-bae4a5c27ddb") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "F.Fab") - (uuid "9bbc928e-40ca-446f-9c1c-de502c9d80e8") - (effects - (font - (size 0.26 0.26) - (thickness 0.04) - ) - ) - ) - (pad "1" smd roundrect - (at -0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Power_Charger/CHG_VSET") + (net "GND") + (pinfunction "GND_B12") (pintype "passive") - (uuid "0115e654-db8a-447a-8bd5-7aa3e4514211") + (uuid "9ce5244b-7662-4ccc-828c-1145c81c913e") ) - (pad "2" smd roundrect - (at 0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) + (pad "SH" thru_hole oval + (at -4.32 -3.13) + (size 1 2.1) + (drill oval 0.6 1.7) + (property pad_prop_mechanical) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) (net "GND") + (pinfunction "SHIELD_SH") (pintype "passive") - (uuid "d26b3470-e240-43db-a1fb-823782b4c158") + (uuid "57cefecf-2448-45e4-985e-3178debf0e84") + ) + (pad "SH" thru_hole oval + (at -4.32 1.05) + (size 1 1.6) + (drill oval 0.6 1.2) + (property pad_prop_mechanical) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (net "GND") + (pinfunction "SHIELD_SH") + (pintype "passive") + (uuid "15d379f9-3703-4f9f-aa6c-631170b81857") + ) + (pad "SH" thru_hole oval + (at 4.32 -3.13) + (size 1 2.1) + (drill oval 0.6 1.7) + (property pad_prop_mechanical) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (net "GND") + (pinfunction "SHIELD_SH") + (pintype "passive") + (uuid "16f7985b-903c-4f8f-84d0-bd4c85a63661") + ) + (pad "SH" thru_hole oval + (at 4.32 1.05) + (size 1 1.6) + (drill oval 0.6 1.2) + (property pad_prop_mechanical) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (net "GND") + (pinfunction "SHIELD_SH") + (pintype "passive") + (uuid "54c491e6-1186-429c-9562-112dfbe29e7c") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KIPRJMOD}/libraries/3dmodels/USB_C_Receptacle_HRO_TYPE-C-31-M-12.step" (offset - (xyz 0 0 0) + (xyz 0 -1.05 0) ) (scale (xyz 1 1 1) ) (rotate - (xyz 0 0 0) + (xyz 0 0 180) ) ) ) @@ -8052,7 +7433,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:47" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:49" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -8095,7 +7476,7 @@ (pins "2'" "2" "a" "1" "3" "1'" "3'" "c") ) ) - (attr through_hole exclude_from_bom) + (attr through_hole exclude_from_pos_files exclude_from_bom) (duplicate_pad_numbers_are_jumpers no) (fp_circle (center 0 0) @@ -8223,7 +7604,7 @@ (drill 1.05) (layers "*.Cu" "*.Mask") (remove_unused_layers no) - (net "/MCU_Core/3V3_RF") + (net "3V3") (pinfunction "X_HI_3") (pintype "passive") (solder_mask_margin 0.1) @@ -8233,480 +7614,60 @@ (at 8.73 -2.5) (size 2.05 2.05) (drill 1.05) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "/MCU_Core/3V3_RF") - (pinfunction "Y_HI_3'") - (pintype "passive") - (solder_mask_margin 0.1) - (uuid "ee150305-dfc4-439a-8de7-4aa31fdd7444") - ) - (pad "a" thru_hole circle - (at -3.25 5.75) - (size 2.25 2.25) - (drill 1.25) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "/MCU_Core/BTN_STICK") - (pinfunction "SW_A_a") - (pintype "passive") - (solder_mask_margin 0.1) - (uuid "fcb12dc2-ca2f-4f10-897e-202b39ecd1cd") - ) - (pad "b" thru_hole circle - (at 3.25 5.75) - (size 2.25 2.25) - (drill 1.25) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (solder_mask_margin 0.1) - (uuid "72d264f0-e108-4ec5-8d33-160e2fc0912a") - ) - (pad "c" thru_hole circle - (at -3.25 10.25) - (size 2.25 2.25) - (drill 1.25) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "SW_C_c") - (pintype "passive") - (solder_mask_margin 0.1) - (uuid "d0ba1a7c-91b6-4320-883f-65e7cc39a9cd") - ) - (pad "d" thru_hole circle - (at 3.25 10.25) - (size 2.25 2.25) - (drill 1.25) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (solder_mask_margin 0.1) - (uuid "48ae7bf1-8e41-47e8-8b4d-8f16664a84c1") - ) - (embedded_fonts no) - (model "${KIPRJMOD}/libraries/3dmodels/Thumbstick_ALPS_RKJXV1224005.step" - (offset - (xyz 0 0 11.4) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) - (footprint "Resistor_SMD:R_0402_1005Metric" - (layer "F.Cu") - (uuid "bc301f15-db6e-4666-91d7-22b9bf096c69") - (at 125.16 117.315 180) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_STAT1" - (at 0 -1.17 180) - (layer "F.SilkS") - (hide yes) - (uuid "456ecacb-6861-4150-a2be-34cf9f63c832") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Value" "10kΩ" - (at 0 1.17 180) - (layer "F.Fab") - (uuid "1b38bcb2-b9f0-4354-bfc1-2e14c19c2f09") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Datasheet" "" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "bb0d5721-aa25-45c7-b06c-795a883794a8") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "Description" "Resistor" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "688fca96-0a4a-4897-838d-de6aa5307509") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "770d71d3-f3b5-4e41-a939-736593463f65") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Manufacturer_Part_Number" "0402WGF1002TCE" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "158073f6-be48-475e-b753-2a8e4cc57a65") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "LCSC" "C25744" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "5b2c2c91-8219-42f2-8638-637715eda273") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Stackup Path" "R_STAT1" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "1d3aadb7-20bf-4d44-8bec-4f505b958fba") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:66" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "ff1ab658-35f9-492c-874b-ad98eb93b05a") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property ki_fp_filters "R_*") - (path "/49093ee7-a404-5ac1-b4ee-14373f94d3cb") - (units - (unit - (name "A") - (pins "1" "2") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "37155dc7-71df-4640-b961-fafa91ecfc48") - ) - (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "0498793a-72c5-44f1-8bd3-d409e0f1d659") - ) - (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "86976913-e161-491d-bcee-12b0d350c357") - ) - (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "F.Fab") - (uuid "3945b37c-6b7c-4570-80f3-841d644b7d70") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "F.Fab") - (uuid "16d49a3b-4437-450b-ad40-77d62cf9c08b") - (effects - (font - (size 0.26 0.26) - (thickness 0.04) - ) - ) - ) - (pad "1" smd roundrect - (at -0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/MCU_Core/STAT1") - (pintype "passive") - (uuid "f0ef7273-1499-4d67-b1f1-7ca063c1a475") - ) - (pad "2" smd roundrect - (at 0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "3V3") - (pintype "passive") - (uuid "abdcac3e-8c2e-4643-9268-4b5673b73cf9") - ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) - (footprint "Resistor_SMD:R_0402_1005Metric" - (layer "F.Cu") - (uuid "bdb71cfa-e4dd-4942-9c65-01570ccf25a6") - (at 122.28 116.515 180) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_ISET1" - (at 0 -1.17 180) - (layer "F.SilkS") - (hide yes) - (uuid "5e6088dd-9c33-4bc3-8eee-c89cd0f94065") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Value" "604Ω" - (at 0 1.17 180) - (layer "F.Fab") - (uuid "f027cebe-49d5-49e6-a92f-4d7877f2f125") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Datasheet" "" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "56adb090-8388-438a-8aa5-a7a90520d4a6") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "Description" "Resistor" - (at 0 0 180) - (layer "F.Fab") - (hide yes) - (uuid "1ab6c9c1-0651-4b8a-b292-2191d1c40c23") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "MF" "Yageo" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "93dd57e3-770b-42aa-be24-b8ff6a89ee2c") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Manufacturer_Part_Number" "AC0402FR-07604RL" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "c5f42212-90cd-48ed-aa3a-520473a4aad6") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "LCSC" "C227167" - (at 0 0 0) - (unlocked yes) - (layer "F.Fab") - (hide yes) - (uuid "5c14eb78-297f-4dbb-9b25-0673f1b19edb") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - ) - ) - (property "Stackup Path" "R_ISET1" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "e0499828-6650-443b-bf0f-547b948b76aa") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:62" - (at 0 2 180) - (layer "F.SilkS") - (hide yes) - (uuid "1983bfb0-9674-410c-8bbd-b464c2145847") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property ki_fp_filters "R_*") - (path "/2fe72eb7-3d6a-5c32-af62-a1e01e62a952") - (units - (unit - (name "A") - (pins "1" "2") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "c52fb6f1-a4af-41a8-9301-e057c59d8518") - ) - (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "23bb6bad-11f5-411f-ab80-70247bd3017e") - ) - (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "F.CrtYd") - (uuid "2c117a4d-e0b3-4c82-b11b-3c1d5965bf1b") - ) - (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "F.Fab") - (uuid "b35989b2-e151-4d5d-a2f1-819bb5613383") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "F.Fab") - (uuid "6821b019-6c3a-42ba-8035-e3c683d3a27e") - (effects - (font - (size 0.26 0.26) - (thickness 0.04) - ) - ) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (net "3V3") + (pinfunction "Y_HI_3'") + (pintype "passive") + (solder_mask_margin 0.1) + (uuid "ee150305-dfc4-439a-8de7-4aa31fdd7444") ) - (pad "1" smd roundrect - (at -0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Power_Charger/CHG_ISET") + (pad "a" thru_hole circle + (at -3.25 5.75) + (size 2.25 2.25) + (drill 1.25) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (net "/MCU_Core/BTN_STICK") + (pinfunction "SW_A_a") (pintype "passive") - (uuid "0e57cbae-1176-4079-835c-c089cc4ef2cb") + (solder_mask_margin 0.1) + (uuid "fcb12dc2-ca2f-4f10-897e-202b39ecd1cd") ) - (pad "2" smd roundrect - (at 0.51 0 180) - (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) + (pad "b" thru_hole circle + (at 3.25 5.75) + (size 2.25 2.25) + (drill 1.25) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (solder_mask_margin 0.1) + (uuid "72d264f0-e108-4ec5-8d33-160e2fc0912a") + ) + (pad "c" thru_hole circle + (at -3.25 10.25) + (size 2.25 2.25) + (drill 1.25) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) (net "GND") + (pinfunction "SW_C_c") (pintype "passive") - (uuid "d76c8050-af3e-4bf0-a359-2060ec100e76") + (solder_mask_margin 0.1) + (uuid "d0ba1a7c-91b6-4320-883f-65e7cc39a9cd") + ) + (pad "d" thru_hole circle + (at 3.25 10.25) + (size 2.25 2.25) + (drill 1.25) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (solder_mask_margin 0.1) + (uuid "48ae7bf1-8e41-47e8-8b4d-8f16664a84c1") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KIPRJMOD}/libraries/3dmodels/Thumbstick_ALPS_RKJXV1224005.step" (offset - (xyz 0 0 0) + (xyz 0 0 11.4) ) (scale (xyz 1 1 1) @@ -8818,7 +7779,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:26" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:28" (at -2 0 90) (layer "F.SilkS") (hide yes) @@ -8927,11 +7888,11 @@ (footprint "Resistor_SMD:R_0402_1005Metric" (layer "F.Cu") (uuid "c6a18d52-780f-4ce4-ba42-6ab67d3472ee") - (at 127.75 122.6) + (at 127.9 122.99 90) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") (property "Reference" "R_RGB1" - (at 0 -1.17 0) + (at 0 -1.17 90) (layer "F.SilkS") (hide yes) (uuid "d9a5945c-44c9-4741-a158-daee4aecb82f") @@ -8943,7 +7904,7 @@ ) ) (property "Value" "470Ω" - (at 0 1 0) + (at 0 1 90) (layer "F.Fab") (uuid "ae970078-388a-4ae9-a4f0-de4b2bf6cdbe") (effects @@ -8954,7 +7915,7 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") (hide yes) (uuid "36e3b84a-4404-4ad6-8433-c1706d9eb94e") @@ -8965,7 +7926,7 @@ ) ) (property "Description" "Resistor" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") (hide yes) (uuid "18e09cc8-eece-4376-8adb-cc8f708258b0") @@ -8976,7 +7937,7 @@ ) ) (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 0) + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) @@ -8989,7 +7950,7 @@ ) ) (property "Manufacturer_Part_Number" "0402WGF4700TCE" - (at 0 0 0) + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) @@ -9002,7 +7963,7 @@ ) ) (property "LCSC" "C25117" - (at 0 0 0) + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) @@ -9015,7 +7976,7 @@ ) ) (property "Stackup Path" "R_RGB1" - (at -2 0 270) + (at -2 0 0) (layer "F.SilkS") (hide yes) (uuid "0e9e0302-6113-4ae2-9a6f-e962a0a1314d") @@ -9026,8 +7987,8 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:65" - (at -2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:68" + (at -2 0 0) (layer "F.SilkS") (hide yes) (uuid "5990c844-a527-492d-a59b-78e49f587a30") @@ -9091,7 +8052,7 @@ (uuid "cfb36a8f-c47e-4c97-a90c-718a7444462b") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") (uuid "2f5e1fe8-5d7d-4f75-9872-794251b05870") (effects @@ -9102,7 +8063,7 @@ ) ) (pad "1" smd roundrect - (at -0.51 0) + (at -0.51 0 90) (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) @@ -9111,7 +8072,7 @@ (uuid "942b8a2e-9ad2-48ec-b83f-cec19b273930") ) (pad "2" smd roundrect - (at 0.51 0) + (at 0.51 0 90) (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) @@ -9132,17 +8093,17 @@ ) ) ) - (footprint "Resistor_SMD:R_0402_1005Metric" + (footprint "MountingHole:MountingHole_2.2mm_M2_ISO14580" (layer "F.Cu") - (uuid "c92b6f9f-9044-4da5-bd6e-fe98134d0be4") - (at 131.975 106.55 -90) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_FB1" - (at 0 -1.17 90) + (uuid "c94ca239-4d3e-4003-bbf0-3b858197fcfb") + (at 147.4 62.8) + (descr "Mounting Hole 2.2mm, M2, no annular, generated by kicad-footprint-generator mountinghole.py") + (tags "mountinghole M2 ISO14580") + (property "Reference" "MH2" + (at 0 -2.85 0) (layer "F.SilkS") (hide yes) - (uuid "aa331657-6526-4ab1-9f57-21a9badb2692") + (uuid "7103ca0b-aa62-43aa-895d-3d107d4ff5d0") (effects (font (size 1 1) @@ -9150,10 +8111,117 @@ ) ) ) - (property "Value" "255kΩ" - (at 0 1.17 90) + (property "Value" "MountingHole_2.2mm_M2_ISO14580" + (at 0 2.85 0) (layer "F.Fab") - (uuid "1238173b-a4f4-4f58-b3ac-c3d2f5c548fe") + (uuid "4330c46d-1f01-48bb-85e7-786b5d99236e") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Datasheet" "" + (at 0 0 0) + (layer "F.Fab") + (hide yes) + (uuid "22756091-c87b-4e43-893a-5a33b59b8113") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "Description" "" + (at 0 0 0) + (layer "F.Fab") + (hide yes) + (uuid "ff24604d-01cb-4022-aea4-4f8379e26ccf") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "KiLib_Generator" "mounting_hardware/mounting_hole" + (at 0 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "8d651497-54e2-4e38-b159-4475d42744be") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (attr board_only exclude_from_pos_files exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (fp_circle + (center 0 0) + (end 1.9 0) + (stroke + (width 0.15) + (type solid) + ) + (fill no) + (layer "Cmts.User") + (uuid "2c0fecca-48b6-4d97-8d20-540dc9cc1496") + ) + (fp_circle + (center 0 0) + (end 2.15 0) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "F.CrtYd") + (uuid "d3d1fa23-6b83-441c-bfbb-eaa6df3d90b4") + ) + (fp_text user "${REFERENCE}" + (at 0 0 0) + (layer "F.Fab") + (uuid "0494d630-0d0e-46b7-a51d-799b2ed19cbf") + (effects + (font + (size 0.95 0.95) + (thickness 0.14) + ) + ) + ) + (pad "" np_thru_hole circle + (at 0 0) + (size 2.2 2.2) + (drill 2.2) + (layers "*.Cu" "*.Mask") + (uuid "523c4cb4-417a-4691-89ac-4fb073f50027") + ) + (embedded_fonts no) + ) + (footprint "Capacitor_SMD:C_0402_1005Metric" + (layer "F.Cu") + (uuid "ca4cc822-1396-4067-bc37-2989a1e547e5") + (at 140.6 101.6 90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_3V3_2" + (at 0 -1.16 90) + (layer "F.SilkS") + (hide yes) + (uuid "3433c062-6fe5-4dbe-8353-7e2cd8228e5b") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Value" "100nF" + (at 0 1.16 90) + (layer "F.Fab") + (uuid "47e8f512-7114-4085-b25d-44a4a9835374") (effects (font (size 1 1) @@ -9165,30 +8233,30 @@ (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "f11cec6a-58c2-4975-90f3-bbc35a490baf") + (uuid "adac23db-5313-4fdc-8aff-cf571c7789c8") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "Resistor" + (property "Description" "Unpolarized capacitor" (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "6c7284d5-72ce-4b45-945a-c742fb732ae1") + (uuid "c6843d3e-5773-4488-acd9-3af0e3b0f331") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Yageo" + (property "MF" "Samsung Electro-Mechanics" (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "f69fa09e-a605-46ff-9957-86c9c379c29b") + (uuid "32c794a1-68ab-47dc-89e5-098e3776a769") (effects (font (size 1 1) @@ -9196,12 +8264,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "RC0402FR-07255KL" + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "76b2cd8c-7511-4011-b965-72c570f32567") + (uuid "c3166ad1-28ae-4f86-8614-0132c01396f9") (effects (font (size 1 1) @@ -9209,12 +8277,12 @@ ) ) ) - (property "LCSC" "C327361" + (property "LCSC" "C1525" (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "5d99b27d-692b-46c3-bd3f-f6e86402ecf1") + (uuid "30778bb9-0cc4-4c3e-801d-d6d01078c321") (effects (font (size 1 1) @@ -9222,34 +8290,32 @@ ) ) ) - (property "Stackup Path" "R_FB1" - (at -2 0 180) + (property "Stackup Path" "C_3V3_2" + (at 2 0 0) (layer "F.SilkS") (hide yes) - (uuid "6707385a-0a74-4cb9-9543-6d4884fee472") + (uuid "063a48ed-2a44-4cf7-90dd-b760708edd22") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:57" - (at -2 0 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:22" + (at 2 0 0) (layer "F.SilkS") (hide yes) - (uuid "93ef101b-d7ab-44a2-8ef0-994b36a8d15f") + (uuid "b0014fce-7c4a-4267-b2dc-e5a823ee9019") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "R_*") - (path "/56d198ab-e2b1-526a-ada9-1e646d15ad03") + (property ki_fp_filters "C_*") + (path "/008fd044-38d8-5b0c-a9aa-e2799ecdf39b") (units (unit (name "A") @@ -9259,78 +8325,78 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "0fdb9e0a-7131-4414-9f25-f3c5889305c6") + (uuid "442cbd50-4ae2-4705-bed2-d0fdbb666ed0") ) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "94a7d12f-a4f3-493d-8c18-10cf9faeef6d") + (uuid "a5ad6d04-fbf4-4e6e-80dd-796da04a7f27") ) (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) + (start -0.91 -0.46) + (end 0.91 0.46) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "4453c6d8-06f3-49f7-afce-d3f54ccfaf64") + (uuid "9e7757e3-6e00-43a6-8d9b-3d197173d7ce") ) (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) + (start -0.5 -0.25) + (end 0.5 0.25) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "39215052-6048-4112-abe5-25ed6b09cd83") + (uuid "ccbc299d-c428-4544-b7aa-ab47e8db76a8") ) (fp_text user "${REFERENCE}" (at 0 0 90) (layer "F.Fab") - (uuid "df404f11-cd7a-4ba1-a2d0-19d956b9d4f9") + (uuid "87cf8e1b-4a69-45d2-95a4-cb2a08785ca0") (effects (font - (size 0.26 0.26) + (size 0.25 0.25) (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -0.51 0 270) - (size 0.54 0.64) + (at -0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Power_Buck/BUCK_FB") + (net "3V3") (pintype "passive") - (uuid "b473d090-9fc9-4083-9b39-173a9b01b011") + (uuid "86978152-f2d0-4efd-b75d-f23d9f97e1bc") ) (pad "2" smd roundrect - (at 0.51 0 270) - (size 0.54 0.64) + (at 0.48 0 90) + (size 0.56 0.62) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "3V3") + (net "GND") (pintype "passive") - (uuid "45c59866-7bc3-4147-88cf-811128d54c92") + (uuid "57f52144-7359-4b8d-a560-d4f69d74d24d") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -9342,17 +8408,17 @@ ) ) ) - (footprint "MountingHole:MountingHole_2.2mm_M2_ISO14580" + (footprint "Capacitor_SMD:C_0603_1608Metric" (layer "F.Cu") - (uuid "c94ca239-4d3e-4003-bbf0-3b858197fcfb") - (at 147.4 62.8) - (descr "Mounting Hole 2.2mm, M2, no annular, generated by kicad-footprint-generator mountinghole.py") - (tags "mountinghole M2 ISO14580") - (property "Reference" "MH2" - (at 0 -2.85 0) + (uuid "cad46504-6d0e-4285-af11-4a75d8535790") + (at 145.3 106 90) + (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_3V3_1" + (at 0 -1.43 270) (layer "F.SilkS") (hide yes) - (uuid "7103ca0b-aa62-43aa-895d-3d107d4ff5d0") + (uuid "29f569ca-8997-4790-89a9-5c670cb77ef6") (effects (font (size 1 1) @@ -9360,10 +8426,10 @@ ) ) ) - (property "Value" "MountingHole_2.2mm_M2_ISO14580" - (at 0 2.85 0) + (property "Value" "10µF" + (at 0 1.43 270) (layer "F.Fab") - (uuid "4330c46d-1f01-48bb-85e7-786b5d99236e") + (uuid "0c37499e-eeea-411d-837b-b1b106396141") (effects (font (size 1 1) @@ -9372,32 +8438,33 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 270) (layer "F.Fab") (hide yes) - (uuid "22756091-c87b-4e43-893a-5a33b59b8113") + (uuid "31e3334d-3e8f-45a8-823b-e18db62e6f35") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "" - (at 0 0 0) + (property "Description" "Unpolarized capacitor" + (at 0 0 270) (layer "F.Fab") (hide yes) - (uuid "ff24604d-01cb-4022-aea4-4f8379e26ccf") + (uuid "731eb54d-62ef-4612-8882-99555f6fb3e6") (effects (font (size 1.27 1.27) ) ) ) - (property "KiLib_Generator" "mounting_hardware/mounting_hole" - (at 0 0 0) - (layer "F.SilkS") + (property "MF" "Samsung Electro-Mechanics" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") (hide yes) - (uuid "8d651497-54e2-4e38-b159-4475d42744be") + (uuid "5cf3f603-bf5d-493d-8542-22e814607d90") (effects (font (size 1 1) @@ -9405,61 +8472,162 @@ ) ) ) - (attr board_only exclude_from_pos_files exclude_from_bom) + (property "Manufacturer_Part_Number" "CL10A106KP8NNNC" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "da606c56-37e7-4acc-9b07-336c3beab960") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "LCSC" "C19702" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "96c5e9e9-0c61-4baa-bb7e-98c929770dc4") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "C_3V3_1" + (at -2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "073aac27-27c6-47bb-a3ba-7fad83cb148b") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:21" + (at -2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "1057e9d5-e6d1-4be5-b02e-25d32c274185") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "C_*") + (path "/b4d4419c-0878-52d2-974a-2ccc35b2ca95") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) (duplicate_pad_numbers_are_jumpers no) - (fp_circle - (center 0 0) - (end 1.9 0) + (fp_line + (start -0.14058 -0.51) + (end 0.14058 -0.51) (stroke - (width 0.15) + (width 0.12) (type solid) ) - (fill no) - (layer "Cmts.User") - (uuid "2c0fecca-48b6-4d97-8d20-540dc9cc1496") + (layer "F.SilkS") + (uuid "7fe2c87e-beed-4403-a001-3c170a7b804a") ) - (fp_circle - (center 0 0) - (end 2.15 0) + (fp_line + (start -0.14058 0.51) + (end 0.14058 0.51) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "58efd5af-4061-4746-a119-98c37d69ecca") + ) + (fp_rect + (start -1.48 -0.73) + (end 1.48 0.73) (stroke (width 0.05) (type solid) ) (fill no) (layer "F.CrtYd") - (uuid "d3d1fa23-6b83-441c-bfbb-eaa6df3d90b4") + (uuid "a2117227-d851-46df-aaf9-d0c3c0bc9647") + ) + (fp_rect + (start -0.8 -0.4) + (end 0.8 0.4) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "F.Fab") + (uuid "1df0fc4c-36be-40d6-918a-4cc50e2e48d6") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 270) (layer "F.Fab") - (uuid "0494d630-0d0e-46b7-a51d-799b2ed19cbf") + (uuid "d9f791a3-4207-4fa7-b561-99cb0982dec3") (effects (font - (size 0.95 0.95) - (thickness 0.14) + (size 0.4 0.4) + (thickness 0.06) ) ) ) - (pad "" np_thru_hole circle - (at 0 0) - (size 2.2 2.2) - (drill 2.2) - (layers "*.Cu" "*.Mask") - (uuid "523c4cb4-417a-4691-89ac-4fb073f50027") + (pad "1" smd roundrect + (at -0.775 0 90) + (size 0.9 0.95) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "3V3") + (pintype "passive") + (uuid "ddb259fd-1ab8-4fd4-b8bf-a9bb6dcfac21") + ) + (pad "2" smd roundrect + (at 0.775 0 90) + (size 0.9 0.95) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "5f3f9d5f-9576-4fab-9431-67d5fb32df74") ) (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) ) - (footprint "Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010" + (footprint "Resistor_SMD:R_0402_1005Metric" + (placed yes) (layer "F.Cu") - (uuid "d43404ad-8460-4a87-82d5-d0adaaee7c0c") - (at 121.8 83.5 -90) - (descr "Side push button (https://www.alps.com/prod/info/E/PDF/Tact/SurfaceMount/SKRT/SKRT.pdf)") - (tags "push horizontal SPST 1P1T") - (property "Reference" "SW_THR_DN1" - (at 0 -2.7 90) + (uuid "cfa4e7e5-e902-43d0-b905-c5edd76d51e2") + (at 129.8 101.41 -90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_VSYS1" + (at 0 -1.17 90) (layer "F.SilkS") (hide yes) - (uuid "da45069d-9a8a-4ad0-8c7b-774692b5e875") + (uuid "49ada08e-3964-4c14-9fb7-fbfab1f09fd2") (effects (font (size 1 1) @@ -9467,10 +8635,10 @@ ) ) ) - (property "Value" "SKRTLAE010" - (at 0 2.9 90) + (property "Value" "200kΩ" + (at 0 1.17 90) (layer "F.Fab") - (uuid "d385d2c5-fb88-4264-8a25-cbba110dc50f") + (uuid "0eb8d120-ce27-44d5-897c-6f25ad17544f") (effects (font (size 1 1) @@ -9479,37 +8647,33 @@ ) ) (property "Datasheet" "" - (at 0 0 270) - (unlocked yes) + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "85254b02-5f20-47f2-a498-18d85ce3ffbf") + (uuid "5add302c-b907-4fd3-b071-6b6c24ba0059") (effects (font (size 1.27 1.27) - (thickness 0.15) ) ) ) - (property "Description" "Push button switch, generic, two pins" - (at 0 0 270) - (unlocked yes) + (property "Description" "Resistor" + (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "db035f9f-5f7e-499c-ac16-6f66de4e5626") + (uuid "9f0f991d-73df-46f5-a81b-296489cfbbf9") (effects (font (size 1.27 1.27) - (thickness 0.15) ) ) ) - (property "MF" "Alps Alpine" + (property "MF" "UNI-ROYAL(Uniroyal Elec)" (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "e06994b5-f7db-4edb-abb8-4b6b67231615") + (uuid "54f7ff02-74f7-4c81-afb8-b3af2942bc9b") (effects (font (size 1 1) @@ -9517,12 +8681,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "SKRTLAE010" + (property "Manufacturer_Part_Number" "0402WGF2003TCE" (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "ab027c4a-16be-4645-98e9-5407bcb04534") + (uuid "21155c86-0810-4b70-9d92-def481c0bf08") (effects (font (size 1 1) @@ -9530,12 +8694,12 @@ ) ) ) - (property "LCSC" "C110293" + (property "LCSC" "C25764" (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "eb1daaba-37c9-401f-9385-df421247842f") + (uuid "78d395ea-2188-4ef7-9098-ca0bc8bea8e6") (effects (font (size 1 1) @@ -9543,11 +8707,11 @@ ) ) ) - (property "Stackup Path" "SW_THR_DN1" - (at 2 0 0) + (property "Stackup Path" "R_VSYS1" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "abbc8d0e-43b8-4837-a421-65f9c773f19f") + (uuid "2e98c534-3a48-4114-80b8-f694da45a663") (effects (font (size 1.27 1.27) @@ -9555,11 +8719,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:82" - (at 2 0 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:75" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "a984006b-1baf-44bc-a64e-8ba878e32d0d") + (uuid "bd9ed807-d5c8-4d99-841e-f600d0fb2dd0") (effects (font (size 1.27 1.27) @@ -9567,7 +8731,8 @@ ) ) ) - (path "/d8be4626-cc79-54d5-b968-a32cfe50ae76") + (property ki_fp_filters "R_*") + (path "/3a5f22cb-80f5-5db2-96cc-fadabb0102ec") (units (unit (name "A") @@ -9577,316 +8742,286 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -1 1.3) - (end 1 1.3) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "39528e89-250f-4f69-949c-4b6ec39d7a60") + (uuid "3dd8c954-aaff-41de-bc7e-dfc7b8b02f81") ) (fp_line - (start -2.4 -1.5) - (end -2.4 -0.5) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "ce67a921-a763-4202-9ec3-c265e5b294a7") + (uuid "b4bc846b-b386-417e-ad40-324dceca41e1") ) - (fp_line - (start -1.8 -1.5) - (end -2.4 -1.5) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "F.SilkS") - (uuid "e8ffbee5-13e7-488b-893d-2f84cefc9d93") + (fill no) + (layer "F.CrtYd") + (uuid "b53578ed-630f-4302-9a54-72698c6571ab") ) - (fp_line - (start 1.8 -1.5) - (end 2.4 -1.5) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "F.SilkS") - (uuid "8f694277-2a18-4fde-813d-f768c48231d4") + (fill no) + (layer "F.Fab") + (uuid "23f2b046-0d47-4e71-98c8-84ecca04a855") ) - (fp_line - (start 2.4 -1.5) - (end 2.4 -0.5) - (stroke - (width 0.12) - (type solid) + (fp_text user "${REFERENCE}" + (at 0 0 90) + (layer "F.Fab") + (uuid "90ebf47f-4733-4bcf-b6f1-11e75f4862ee") + (effects + (font + (size 0.26 0.26) + (thickness 0.04) + ) ) - (layer "F.SilkS") - (uuid "224f8b57-102f-4ac5-9ee8-c9ef42b0ba9c") ) - (fp_line - (start -1 1.5) - (end 1 1.5) - (stroke - (width 0.1) - (type solid) - ) - (layer "Dwgs.User") - (uuid "fa877274-c172-4a59-ae78-84cc39e43f1d") + (pad "1" smd roundrect + (at -0.51 0 270) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "VSYS") + (pintype "passive") + (uuid "f6449fe1-0879-4f27-a9df-9cf6e30e52d5") ) - (fp_line - (start -1 1.5) - (end -0.5 0.3) - (stroke - (width 0.1) - (type solid) - ) - (layer "Dwgs.User") - (uuid "ebe56264-a659-496c-8348-d579fd1b2f69") + (pad "2" smd roundrect + (at 0.51 0 270) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/MCU_Core/VSYS_SENSE") + (pintype "passive") + (uuid "f3d8872a-314d-4e33-90a1-1412a546e363") ) - (fp_line - (start -0.5 1.5) - (end 0 0.3) - (stroke - (width 0.1) - (type solid) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (offset + (xyz 0 0 0) ) - (layer "Dwgs.User") - (uuid "3fa50623-c65f-49fb-8f43-0b761c91e6a9") - ) - (fp_line - (start 0 1.5) - (end 0.5 0.3) - (stroke - (width 0.1) - (type solid) + (scale + (xyz 1 1 1) ) - (layer "Dwgs.User") - (uuid "883fbf9a-47b3-4b0b-82c2-5d745735578b") - ) - (fp_line - (start 0.5 1.5) - (end 1 0.3) - (stroke - (width 0.1) - (type solid) + (rotate + (xyz 0 0 0) ) - (layer "Dwgs.User") - (uuid "bf1ccede-42ac-46b1-b32f-8199471424bc") ) - (fp_line - (start 1 1.5) - (end 1 0.3) - (stroke - (width 0.1) - (type solid) + ) + (footprint "R_0402_1005Metric" + (layer "F.Cu") + (uuid "d346f618-f69f-4027-8b04-258984dccb4a") + (at 125.5 105.79 -90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_I2C_SDA1" + (at 0 -1.17 90) + (layer "F.SilkS") + (hide yes) + (uuid "738fc9b4-4996-4ea5-8ec0-1ce90b895bb5") + (effects + (font + (size 1 1) + (thickness 0.15) + ) ) - (layer "Dwgs.User") - (uuid "1802a0ee-f82c-486d-9f68-b585eb162575") ) - (fp_line - (start -1 0.3) - (end -1 1.5) - (stroke - (width 0.1) - (type solid) + (property "Value" "4.7kΩ" + (at 0 1.17 90) + (layer "F.Fab") + (uuid "d91538c1-d581-494b-beb1-8b0c257178f0") + (effects + (font + (size 1 1) + (thickness 0.15) + ) ) - (layer "Dwgs.User") - (uuid "94e0bd2f-76e5-4c61-bbfd-9f481944ddfa") ) - (fp_line - (start 1 0.3) - (end -1 0.3) - (stroke - (width 0.1) - (type solid) + (property "Datasheet" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "b9d928ce-7af4-447c-91a2-3edc0aecaeb4") + (effects + (font + (size 1.27 1.27) + ) ) - (layer "Dwgs.User") - (uuid "774bcd66-a088-4056-bd23-969b0441467c") ) - (fp_line - (start -2.83 2.3) - (end 2.83 2.3) - (stroke - (width 0.05) - (type solid) + (property "Description" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "53468e53-1f79-428c-a37a-036a1e88f2c8") + (effects + (font + (size 1.27 1.27) + ) ) - (layer "F.CrtYd") - (uuid "1eb5133d-8d93-4c04-b880-350c0035f5c5") ) - (fp_line - (start -2.83 -2.05) - (end -2.83 2.3) - (stroke - (width 0.05) - (type solid) + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 90) + (layer "F.SilkS") + (hide yes) + (uuid "4d89aa3c-0a29-44cb-867f-b30bb7224e7c") + (effects + (font + (size 1 1) + (thickness 0.15) + ) ) - (layer "F.CrtYd") - (uuid "8a12611d-b229-44e2-9435-0a3b3259af97") ) - (fp_line - (start -2.83 -2.05) - (end 2.83 -2.05) - (stroke - (width 0.05) - (type solid) + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "f680fe11-502a-4225-9fc7-5d52ede6fa08") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "F.CrtYd") - (uuid "ce389500-7927-43ab-9a60-6179c14a2b49") ) - (fp_line - (start 2.83 -2.05) - (end 2.83 2.3) - (stroke - (width 0.05) - (type solid) + (property "Manufacturer_Part_Number" "0402WGF4701TCE" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "e865c2d4-cc91-4fdc-9ed6-a0ce20beb711") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "F.CrtYd") - (uuid "94e30d22-fdcc-42f4-bbab-ba4a248965e7") ) - (fp_line - (start -1 2.04) - (end 1 2.04) - (stroke - (width 0.1) - (type solid) + (property "LCSC" "C25900" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "564aa6eb-b819-4616-a2c6-d4b16bdbd9be") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "F.Fab") - (uuid "1bba543c-e377-4e47-bd69-ca59bc8e7f0f") ) - (fp_line - (start -1 2.04) - (end -1 1.21) - (stroke - (width 0.1) - (type solid) + (property "Stackup Path" "R_I2C_SDA1" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "a7a82439-3804-42e7-ac54-6abc6a2cc15f") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "F.Fab") - (uuid "0d9bc138-b1fa-4c2a-a3bc-e388493323af") ) - (fp_line - (start 1 2.04) - (end 1 1.21) - (stroke - (width 0.1) - (type solid) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:102" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "1b57620b-1182-4682-bb22-eb5a5bbedaab") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "F.Fab") - (uuid "ff6b4140-0fb8-470a-a87a-7b4f613f86d5") ) + (path "/08526ea4-c891-56dc-9aed-02c7f7119ded") + (attr smd) + (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -2.25 1.21) - (end 2.25 1.21) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke - (width 0.1) + (width 0.12) (type solid) ) - (layer "F.Fab") - (uuid "62b92a9b-fb8f-43d9-b421-a81231abcf03") + (layer "F.SilkS") + (uuid "2a619a14-6fcc-48d7-9031-878c6eae6a12") ) (fp_line - (start -2.25 -1.35) - (end -2.25 1.21) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke - (width 0.1) + (width 0.12) (type solid) ) - (layer "F.Fab") - (uuid "d32c50f7-d757-4767-b536-1a8061e51b1c") + (layer "F.SilkS") + (uuid "708d1c81-83cd-42be-8900-db3927c605aa") ) - (fp_line - (start -2.25 -1.35) - (end 2.25 -1.35) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "F.Fab") - (uuid "2e2cf195-01eb-44be-b5f1-674ccd79eba3") + (fill no) + (layer "F.CrtYd") + (uuid "dd49ac63-9ad3-4339-a866-3de93426f4d6") ) - (fp_line - (start 2.25 -1.35) - (end 2.25 1.21) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) (stroke (width 0.1) (type solid) ) + (fill no) (layer "F.Fab") - (uuid "ae1ce2df-9c44-4cfb-b80a-5dd1a38285cd") + (uuid "ef378c00-a63a-444e-a521-3652ee47cca7") ) (fp_text user "${REFERENCE}" (at 0 0 90) (layer "F.Fab") - (uuid "10a1f67e-9315-41e5-9c6b-9f5d8fbc5d41") + (uuid "115bd838-7786-44fe-886a-3c8b6e547c6e") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.26 0.26) + (thickness 0.04) ) ) ) - (pad "" np_thru_hole circle - (at -2.125 0 270) - (size 0.9 0.9) - (drill 0.9) - (layers "*.Cu" "*.Mask") - (uuid "257a443e-9e5f-4327-877a-313e7cd66fa4") - ) - (pad "" np_thru_hole circle - (at 2.125 0 270) - (size 0.9 0.9) - (drill 0.9) - (layers "*.Cu" "*.Mask") - (uuid "992f2bb3-df83-4cb2-9573-a4d54079e7fd") - ) - (pad "1" smd roundrect - (at -1.225 -0.9 270) - (size 0.75 1.8) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Buttons_Direct/BTN_THR_DN") - (pinfunction "1_1") - (pintype "passive") - (uuid "4ec90660-cd8c-4b73-81f0-443dbe558f12") - ) (pad "1" smd roundrect - (at 1.225 -0.9 270) - (size 0.75 1.8) + (at -0.51 0 270) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Buttons_Direct/BTN_THR_DN") - (pinfunction "1_1") - (pintype "passive") - (uuid "f94d8af6-946f-4ad9-bde0-eb3b9133058a") + (net "3V3") + (uuid "8dccc573-6e90-41b1-8eae-e227cb32e447") ) (pad "2" smd roundrect - (at 0 -0.9 270) - (size 0.6 1.8) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "GND") - (pinfunction "2_2") - (pintype "passive") - (uuid "3ec79f82-af67-4bb7-9252-eea63b3dc07b") - ) - (pad "MP" smd roundrect - (at -1.85 1.05 270) - (size 1.3 0.9) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (uuid "959d54c3-a889-402e-9f65-b87d1a9b7b31") - ) - (pad "MP" smd roundrect - (at 1.85 1.05 270) - (size 1.3 0.9) + (at 0.51 0 270) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (uuid "9aa2e4de-b5b2-4bb1-ad5f-898531217c9a") + (net "/Accelerometer/I2C_SDA") + (uuid "427f539e-95aa-448d-a48f-e8c3ec350132") ) (embedded_fonts no) - (model "${KIPRJMOD}/libraries/3dmodels/SW_Alps_SKRTLAE010.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -9900,15 +9035,15 @@ ) (footprint "Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010" (layer "F.Cu") - (uuid "d84bced1-563d-4ee9-afb9-eaae237dbf70") - (at 148.2 73.5 90) + (uuid "d43404ad-8460-4a87-82d5-d0adaaee7c0c") + (at 121.8 83.5 -90) (descr "Side push button (https://www.alps.com/prod/info/E/PDF/Tact/SurfaceMount/SKRT/SKRT.pdf)") (tags "push horizontal SPST 1P1T") - (property "Reference" "SW_VOL_UP1" + (property "Reference" "SW_THR_DN1" (at 0 -2.7 90) (layer "F.SilkS") (hide yes) - (uuid "9839ee46-3419-49d0-994f-650f9ba578ed") + (uuid "da45069d-9a8a-4ad0-8c7b-774692b5e875") (effects (font (size 1 1) @@ -9919,7 +9054,7 @@ (property "Value" "SKRTLAE010" (at 0 2.9 90) (layer "F.Fab") - (uuid "9999d58e-01f0-43e2-b018-b7e50a4c1924") + (uuid "d385d2c5-fb88-4264-8a25-cbba110dc50f") (effects (font (size 1 1) @@ -9928,11 +9063,11 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "4e440a3f-d87d-46dc-890e-f28154048a72") + (uuid "85254b02-5f20-47f2-a498-18d85ce3ffbf") (effects (font (size 1.27 1.27) @@ -9941,11 +9076,11 @@ ) ) (property "Description" "Push button switch, generic, two pins" - (at 0 0 90) + (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "c64c023c-3ab6-430a-90ea-cfb2fe8ee4c6") + (uuid "db035f9f-5f7e-499c-ac16-6f66de4e5626") (effects (font (size 1.27 1.27) @@ -9954,11 +9089,11 @@ ) ) (property "MF" "Alps Alpine" - (at 0 0 90) + (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "7b4f443b-c100-48d3-94c3-98e5a6719dfd") + (uuid "e06994b5-f7db-4edb-abb8-4b6b67231615") (effects (font (size 1 1) @@ -9967,11 +9102,11 @@ ) ) (property "Manufacturer_Part_Number" "SKRTLAE010" - (at 0 0 90) + (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "964ffdfc-9262-49fd-bdc3-c84883ed669b") + (uuid "ab027c4a-16be-4645-98e9-5407bcb04534") (effects (font (size 1 1) @@ -9980,11 +9115,11 @@ ) ) (property "LCSC" "C110293" - (at 0 0 90) + (at 0 0 270) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "ffd33cf1-98bb-414a-bda5-3606035e9d1c") + (uuid "eb1daaba-37c9-401f-9385-df421247842f") (effects (font (size 1 1) @@ -9992,11 +9127,11 @@ ) ) ) - (property "Stackup Path" "SW_VOL_UP1" - (at -2 0 0) + (property "Stackup Path" "SW_THR_DN1" + (at 2 0 0) (layer "F.SilkS") (hide yes) - (uuid "e59e479e-a052-447e-817a-85437be2a307") + (uuid "abbc8d0e-43b8-4837-a421-65f9c773f19f") (effects (font (size 1.27 1.27) @@ -10004,11 +9139,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:86" - (at -2 0 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:85" + (at 2 0 0) (layer "F.SilkS") (hide yes) - (uuid "768d8ced-bdbf-4348-9245-5ac390719e45") + (uuid "a984006b-1baf-44bc-a64e-8ba878e32d0d") (effects (font (size 1.27 1.27) @@ -10016,7 +9151,7 @@ ) ) ) - (path "/16c18574-76f3-5208-aa75-7f5df01a9092") + (path "/d8be4626-cc79-54d5-b968-a32cfe50ae76") (units (unit (name "A") @@ -10026,24 +9161,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start 2.4 -1.5) - (end 2.4 -0.5) + (start -1 1.3) + (end 1 1.3) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "3532fb2f-7360-447e-909a-9f3201b4a11a") + (uuid "39528e89-250f-4f69-949c-4b6ec39d7a60") ) (fp_line - (start 1.8 -1.5) - (end 2.4 -1.5) + (start -2.4 -1.5) + (end -2.4 -0.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "8bbd44e6-28b2-40f1-8f6b-03b9fed009fd") + (uuid "ce67a921-a763-4202-9ec3-c265e5b294a7") ) (fp_line (start -1.8 -1.5) @@ -10053,177 +9188,177 @@ (type solid) ) (layer "F.SilkS") - (uuid "077d03f1-70b9-421e-9792-3109f0717f9b") + (uuid "e8ffbee5-13e7-488b-893d-2f84cefc9d93") ) (fp_line - (start -2.4 -1.5) - (end -2.4 -0.5) + (start 1.8 -1.5) + (end 2.4 -1.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "f93fa75d-8fd6-45d4-a0e9-34fa790f7f59") + (uuid "8f694277-2a18-4fde-813d-f768c48231d4") ) (fp_line - (start -1 1.3) - (end 1 1.3) + (start 2.4 -1.5) + (end 2.4 -0.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "614d9da3-c760-4258-9480-7a6b8ca9d981") + (uuid "224f8b57-102f-4ac5-9ee8-c9ef42b0ba9c") ) (fp_line - (start 1 0.3) - (end -1 0.3) + (start -1 1.5) + (end 1 1.5) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "3624ac8e-e909-4cd1-9a84-481c5e59d3e8") + (uuid "fa877274-c172-4a59-ae78-84cc39e43f1d") ) (fp_line - (start -1 0.3) - (end -1 1.5) + (start -1 1.5) + (end -0.5 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "f1174bf9-799f-4904-9d4b-ae6fe5610c52") + (uuid "ebe56264-a659-496c-8348-d579fd1b2f69") ) (fp_line - (start 1 1.5) - (end 1 0.3) + (start -0.5 1.5) + (end 0 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "0197f2b1-f3ce-47c9-9a44-701326c82ac4") + (uuid "3fa50623-c65f-49fb-8f43-0b761c91e6a9") ) (fp_line - (start 0.5 1.5) - (end 1 0.3) + (start 0 1.5) + (end 0.5 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "b586b234-cdf5-4781-8281-4441cba3a17d") + (uuid "883fbf9a-47b3-4b0b-82c2-5d745735578b") ) (fp_line - (start 0 1.5) - (end 0.5 0.3) + (start 0.5 1.5) + (end 1 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "29f6286a-4559-4b84-b5df-751be9c4d4fe") + (uuid "bf1ccede-42ac-46b1-b32f-8199471424bc") ) (fp_line - (start -0.5 1.5) - (end 0 0.3) + (start 1 1.5) + (end 1 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "d17368d1-194d-4325-8f38-e2874ae799e5") + (uuid "1802a0ee-f82c-486d-9f68-b585eb162575") ) (fp_line - (start -1 1.5) - (end -0.5 0.3) + (start -1 0.3) + (end -1 1.5) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "a4d5077c-80f1-4170-8719-eaa52cb3c538") + (uuid "94e0bd2f-76e5-4c61-bbfd-9f481944ddfa") ) (fp_line - (start -1 1.5) - (end 1 1.5) + (start 1 0.3) + (end -1 0.3) (stroke (width 0.1) (type solid) ) (layer "Dwgs.User") - (uuid "d37d28af-1edc-4505-b940-24d25c2d3244") + (uuid "774bcd66-a088-4056-bd23-969b0441467c") ) (fp_line - (start 2.83 -2.05) + (start -2.83 2.3) (end 2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "32ed1cb7-60bc-4c7a-9cbc-ae9ab60f399a") + (uuid "1eb5133d-8d93-4c04-b880-350c0035f5c5") ) (fp_line (start -2.83 -2.05) - (end 2.83 -2.05) + (end -2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "8736558a-8534-4b72-8847-211f6f660b52") + (uuid "8a12611d-b229-44e2-9435-0a3b3259af97") ) (fp_line (start -2.83 -2.05) - (end -2.83 2.3) + (end 2.83 -2.05) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "eeddff91-f54c-4330-86e7-408a7702185e") + (uuid "ce389500-7927-43ab-9a60-6179c14a2b49") ) (fp_line - (start -2.83 2.3) + (start 2.83 -2.05) (end 2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "28ae4f09-2c6e-40f7-a922-17ec558c3922") + (uuid "94e30d22-fdcc-42f4-bbab-ba4a248965e7") ) (fp_line - (start 2.25 -1.35) - (end 2.25 1.21) + (start -1 2.04) + (end 1 2.04) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "cfcbb8da-b025-43fb-9188-13fa26de2339") + (uuid "1bba543c-e377-4e47-bd69-ca59bc8e7f0f") ) (fp_line - (start -2.25 -1.35) - (end 2.25 -1.35) + (start -1 2.04) + (end -1 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "70a0119c-5749-464b-9c6a-0676cb3805b2") + (uuid "0d9bc138-b1fa-4c2a-a3bc-e388493323af") ) (fp_line - (start -2.25 -1.35) - (end -2.25 1.21) + (start 1 2.04) + (end 1 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "4a22c671-2b68-4ded-a34c-8dad12f0a0dc") + (uuid "ff6b4140-0fb8-470a-a87a-7b4f613f86d5") ) (fp_line (start -2.25 1.21) @@ -10233,42 +9368,42 @@ (type solid) ) (layer "F.Fab") - (uuid "4ba6f573-2330-49fd-81e2-ddefe1158c0d") + (uuid "62b92a9b-fb8f-43d9-b421-a81231abcf03") ) (fp_line - (start 1 2.04) - (end 1 1.21) + (start -2.25 -1.35) + (end -2.25 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "71015b5f-d635-4d3c-9206-7e6d18f7ce11") + (uuid "d32c50f7-d757-4767-b536-1a8061e51b1c") ) (fp_line - (start -1 2.04) - (end -1 1.21) + (start -2.25 -1.35) + (end 2.25 -1.35) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "e6e93c5b-3672-428f-aa09-6850738df417") + (uuid "2e2cf195-01eb-44be-b5f1-674ccd79eba3") ) (fp_line - (start -1 2.04) - (end 1 2.04) + (start 2.25 -1.35) + (end 2.25 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "8c7561a0-d3bd-4734-91d1-90a80b7cfc19") + (uuid "ae1ce2df-9c44-4cfb-b80a-5dd1a38285cd") ) (fp_text user "${REFERENCE}" (at 0 0 90) (layer "F.Fab") - (uuid "494a6678-ec75-40e3-8622-94cb6628936f") + (uuid "10a1f67e-9315-41e5-9c6b-9f5d8fbc5d41") (effects (font (size 1 1) @@ -10277,62 +9412,62 @@ ) ) (pad "" np_thru_hole circle - (at -2.125 0 90) + (at -2.125 0 270) (size 0.9 0.9) (drill 0.9) (layers "*.Cu" "*.Mask") - (uuid "810ba315-1fe7-4937-a998-19577bf16814") + (uuid "257a443e-9e5f-4327-877a-313e7cd66fa4") ) (pad "" np_thru_hole circle - (at 2.125 0 90) + (at 2.125 0 270) (size 0.9 0.9) (drill 0.9) (layers "*.Cu" "*.Mask") - (uuid "4d009025-50cf-44b1-a3be-a4c9c8cb3dd2") + (uuid "992f2bb3-df83-4cb2-9573-a4d54079e7fd") ) (pad "1" smd roundrect - (at -1.225 -0.9 90) + (at -1.225 -0.9 270) (size 0.75 1.8) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Buttons_Direct/BTN_VOL_UP") + (net "/Buttons_Direct/BTN_THR_DN") (pinfunction "1_1") (pintype "passive") - (uuid "1963b1bd-85af-4149-98cc-621d3f3e4363") + (uuid "4ec90660-cd8c-4b73-81f0-443dbe558f12") ) (pad "1" smd roundrect - (at 1.225 -0.9 90) + (at 1.225 -0.9 270) (size 0.75 1.8) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Buttons_Direct/BTN_VOL_UP") + (net "/Buttons_Direct/BTN_THR_DN") (pinfunction "1_1") (pintype "passive") - (uuid "73f29954-949f-4a50-9b34-4946a9cf28da") + (uuid "f94d8af6-946f-4ad9-bde0-eb3b9133058a") ) (pad "2" smd roundrect - (at 0 -0.9 90) + (at 0 -0.9 270) (size 0.6 1.8) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) (net "GND") (pinfunction "2_2") (pintype "passive") - (uuid "4465281e-bf89-46b3-928f-e416edf2488d") + (uuid "3ec79f82-af67-4bb7-9252-eea63b3dc07b") ) (pad "MP" smd roundrect - (at -1.85 1.05 90) + (at -1.85 1.05 270) (size 1.3 0.9) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (uuid "3fae3e4d-f8c7-4f3e-94ce-af13138b5d7a") + (uuid "959d54c3-a889-402e-9f65-b87d1a9b7b31") ) (pad "MP" smd roundrect - (at 1.85 1.05 90) + (at 1.85 1.05 270) (size 1.3 0.9) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (uuid "69939839-9a6a-40a8-9b1c-2abe43824a62") + (uuid "9aa2e4de-b5b2-4bb1-ad5f-898531217c9a") ) (embedded_fonts no) (model "${KIPRJMOD}/libraries/3dmodels/SW_Alps_SKRTLAE010.step" @@ -10347,17 +9482,17 @@ ) ) ) - (footprint "Package_TO_SOT_SMD:SOT-23-5" + (footprint "R_0402_1005Metric" (layer "F.Cu") - (uuid "d9b04e33-9e45-4080-992f-47fe8473b9f2") - (at 140.925 110.9375 -90) - (descr "SOT, 5 Pin (JEDEC MO-178 Var AA https://www.jedec.org/document_search?search_api_views_fulltext=MO-178)") - (tags "SOT TO_SOT_SMD") - (property "Reference" "U_BUCK1" - (at 0 -2.4 90) + (uuid "d5af9a27-8038-480a-9b9a-cff306f2164c") + (at 127.2 106.9 -90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_I2C_SCL1" + (at 0 -1.17 90) (layer "F.SilkS") (hide yes) - (uuid "06c5b817-939d-44a9-b139-7612a9bfda93") + (uuid "f5bfa70f-bd5b-4bb9-9ec6-ce42d3f2ec4a") (effects (font (size 1 1) @@ -10365,10 +9500,10 @@ ) ) ) - (property "Value" "TLV62569DBVR" - (at 0 2.4 90) + (property "Value" "4.7kΩ" + (at 0 1.17 90) (layer "F.Fab") - (uuid "6ea73f51-d66e-44b8-aea0-813ad0f36c8c") + (uuid "de03cfe0-a5d1-4ea1-a4a9-213829a156ba") (effects (font (size 1 1) @@ -10376,34 +9511,33 @@ ) ) ) - (property "Datasheet" "http://www.ti.com/lit/ds/symlink/tlv62569.pdf" + (property "Datasheet" "" (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "7fb1d309-4b2c-4a78-baa9-daa8d50db52d") + (uuid "98dc8002-b5fd-47a0-b715-75feebcbb7b1") (effects (font (size 1.27 1.27) ) ) ) - (property "Description" "High Efficiency Synchronous Buck Converter, Adjustable Output 0.6V-5.5V, 2A, SOT-23-5" + (property "Description" "" (at 0 0 90) (layer "F.Fab") (hide yes) - (uuid "35ac9952-dde7-4311-8a9a-7200d9a7897e") + (uuid "408db257-3f76-4ad0-9edc-d7174aa0114f") (effects (font (size 1.27 1.27) ) ) ) - (property "MF" "Texas Instruments" + (property "KiLib_Generator" "SMD_2terminal_chip_molded" (at 0 0 90) - (unlocked yes) - (layer "F.Fab") + (layer "F.SilkS") (hide yes) - (uuid "816497c5-1865-4ff9-9a65-7ba6842f37ac") + (uuid "d42b7218-dfab-4fb9-a3bc-cf3b2be254ea") (effects (font (size 1 1) @@ -10411,385 +9545,140 @@ ) ) ) - (property "Manufacturer_Part_Number" "TLV62569DBVR" - (at 0 0 90) - (unlocked yes) - (layer "F.Fab") + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "bafc3ee0-4692-4a10-9e92-fecba59e9073") + (uuid "d23f3e8f-f661-4652-81cc-a36f2a3957c1") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "LCSC" "C141836" - (at 0 0 90) - (unlocked yes) - (layer "F.Fab") + (property "Manufacturer_Part_Number" "0402WGF4701TCE" + (at 0 2 90) + (layer "F.SilkS") (hide yes) - (uuid "29de6419-cfee-4931-9e9c-bb14f8038d1b") + (uuid "521cc624-3066-44ce-be12-ef0b1ecebcf6") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) ) ) - (property "Stackup Path" "U_BUCK1" - (at -2 0 180) + (property "LCSC" "C25900" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "179288aa-34c9-454d-b544-4b635438b2bd") + (uuid "b07b3730-dbcd-4794-a8ca-f5f9bc34a66c") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:87" - (at -2 0 180) + (property "Stackup Path" "R_I2C_SCL1" + (at 0 2 90) (layer "F.SilkS") (hide yes) - (uuid "22e59454-0b5c-4792-a7ae-969b2cdbdeac") + (uuid "96c2dafa-e4bc-44db-8ea3-5f1dad43eb6a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "SOT?23*") - (path "/01d79e8b-400a-500d-9fe6-5614a79d1279") - (units - (unit - (name "A") - (pins "4" "1" "2" "3" "5") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:101" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "e5c2c5ae-e612-4981-9981-2f5a4ef15865") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) ) + (path "/5fb0f127-1a56-5891-b4dd-d4ad826bd818") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.91 1.56) - (end -0.91 1.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "a8eb601e-f693-421a-9109-73d5215fa174") - ) - (fp_line - (start 0.91 1.56) - (end -0.91 1.56) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "d9f6cb6b-5e14-4d8f-be5e-db2ed32cff38") - ) - (fp_line - (start 0.91 1.51) - (end 0.91 1.56) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "f01ec1f0-4c70-4a4e-a9d3-f66669c200e1") - ) - (fp_line - (start 0.91 -0.39) - (end 0.91 0.39) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "f697edec-c77d-4821-9063-5ddb6e869bac") - ) - (fp_line - (start -0.91 -1.51) - (end -0.91 -1.56) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "21cfb23b-5952-41bb-b266-41578fda7896") - ) - (fp_line - (start -0.91 -1.56) - (end 0.91 -1.56) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "545707ed-7e63-478f-8323-a1a36b113720") + (uuid "f61ffcbd-1f19-4cbf-a642-555eeecea64c") ) (fp_line - (start 0.91 -1.56) - (end 0.91 -1.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "F.SilkS") - (uuid "7c4f4d0e-1f7c-4142-b9a8-664c1087836a") - ) - (fp_poly - (pts - (xy -1.45 -1.51) (xy -1.69 -1.84) (xy -1.21 -1.84) - ) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) - (fill yes) (layer "F.SilkS") - (uuid "f45cad6c-88d6-448f-a8cd-eb481071c53b") - ) - (fp_line - (start -1.05 1.7) - (end -1.05 1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "7d6ab570-d873-4f8f-b996-2265b74af962") - ) - (fp_line - (start 1.05 1.7) - (end -1.05 1.7) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "cdb35ff1-cfa5-46c7-86a4-1d3105affd9e") - ) - (fp_line - (start -2.05 1.5) - (end -2.05 -1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "4448f008-8002-44d8-9671-f6efe3e6805c") - ) - (fp_line - (start -1.05 1.5) - (end -2.05 1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "4fc87d0e-2edc-48ba-ad1d-27a195e84c7c") - ) - (fp_line - (start 1.05 1.5) - (end 1.05 1.7) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "ae54ad69-dd53-4f0d-8e57-1a6f53f6ffd9") - ) - (fp_line - (start 2.05 1.5) - (end 1.05 1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "a2225891-6b43-4d0e-8b56-52911ca9c8a3") - ) - (fp_line - (start 1.05 0.39) - (end 2.05 0.39) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "438d8665-9576-42c2-b4ca-1527d72d59dd") - ) - (fp_line - (start 2.05 0.39) - (end 2.05 1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "742fc6a7-c222-4cac-9c70-61f6ff131381") - ) - (fp_line - (start 1.05 -0.39) - (end 1.05 0.39) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "70c82a79-83a1-4fa2-a4cf-1083e6f17c77") - ) - (fp_line - (start 2.05 -0.39) - (end 1.05 -0.39) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "a14d3599-168d-4808-aa74-618c2c3b1e06") - ) - (fp_line - (start -2.05 -1.5) - (end -1.05 -1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "75c62025-f1b5-45ec-9f2d-c982aa7758a5") - ) - (fp_line - (start -1.05 -1.5) - (end -1.05 -1.7) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "6dac7f2c-0c58-49d8-9817-8a67a6c6c99b") - ) - (fp_line - (start 1.05 -1.5) - (end 2.05 -1.5) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "8d75752a-aa56-48c1-8959-e46244698f27") - ) - (fp_line - (start 2.05 -1.5) - (end 2.05 -0.39) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "e971f5cd-fdfe-429e-82d5-cd6082c9f504") - ) - (fp_line - (start -1.05 -1.7) - (end 1.05 -1.7) - (stroke - (width 0.05) - (type solid) - ) - (layer "F.CrtYd") - (uuid "7ab74d95-192a-426c-a1b4-a2e7ec6ec1dd") + (uuid "c02fbc22-41ba-4308-beee-479d6dcb2b5b") ) - (fp_line - (start 1.05 -1.7) - (end 1.05 -1.5) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) (stroke (width 0.05) (type solid) ) + (fill no) (layer "F.CrtYd") - (uuid "a0e4cab1-d62e-4437-85d4-25dc0debe539") + (uuid "57a82b97-7942-43b4-8aa1-b86ee24cae6e") ) - (fp_poly - (pts - (xy -0.4 -1.45) (xy 0.8 -1.45) (xy 0.8 1.45) (xy -0.8 1.45) (xy -0.8 -1.05) - ) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "F.Fab") - (uuid "dbcd7dcd-61fb-4a3f-91cf-ee82a5859a1d") + (uuid "c3436346-6e85-4d25-b411-e108841ba1fb") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 90) (layer "F.Fab") - (uuid "fa1f1f86-c023-43b4-aff7-33a022afacc1") + (uuid "015cfff7-5697-43f4-afd3-97413febbee5") (effects (font - (size 0.72 0.72) - (thickness 0.11) + (size 0.26 0.26) + (thickness 0.04) ) ) ) (pad "1" smd roundrect - (at -1.1375 -0.95 270) - (size 1.325 0.6) + (at -0.51 0 270) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Power_Buck/PWR_EN") - (pinfunction "EN_1") - (pintype "input") - (uuid "e7db6b0a-2f2f-4c95-b948-f5c1e980c81b") + (net "3V3") + (uuid "f749124c-52bf-4a7f-9d14-9ea730d0b5f5") ) (pad "2" smd roundrect - (at -1.1375 0 270) - (size 1.325 0.6) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "GND") - (pinfunction "GND_2") - (pintype "power_in") - (uuid "1d1ddd6c-c886-47dc-8b21-6c9ab22afe6a") - ) - (pad "3" smd roundrect - (at -1.1375 0.95 270) - (size 1.325 0.6) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "/Power_Buck/BUCK_SW") - (pinfunction "SW_3") - (pintype "power_out") - (uuid "77ad35fb-9199-4834-b179-52252744a8db") - ) - (pad "4" smd roundrect - (at 1.1375 0.95 270) - (size 1.325 0.6) - (layers "F.Cu" "F.Mask" "F.Paste") - (roundrect_rratio 0.25) - (net "VSYS") - (pinfunction "VIN_4") - (pintype "power_in") - (uuid "cb79d23b-cdd4-4a1d-8408-5f624102d898") - ) - (pad "5" smd roundrect - (at 1.1375 -0.95 270) - (size 1.325 0.6) + (at 0.51 0 270) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") (roundrect_rratio 0.25) - (net "/Power_Buck/BUCK_FB") - (pinfunction "FB_5") - (pintype "input") - (uuid "d09f2f1d-d4d8-4980-b7b5-bfeb7e545160") + (net "/Accelerometer/I2C_SCL") + (uuid "cc52da01-6d7a-4deb-94a4-80ac385aaec6") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-23-5.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -10801,17 +9690,17 @@ ) ) ) - (footprint "Inductor_SMD:L_Bourns-SRN4018" - (layer "F.Cu") - (uuid "df90bff6-7d55-4fb3-80be-b1a124878c17") - (at 135.975 109.8 180) - (descr "Bourns SRN4018 series SMD inductor, https://www.bourns.com/docs/Product-Datasheets/SRN4018.pdf") - (tags "Bourns SRN4018 SMD inductor") - (property "Reference" "L_BUCK1" - (at 0 3.1 180) + (footprint "Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010" + (layer "F.Cu") + (uuid "d84bced1-563d-4ee9-afb9-eaae237dbf70") + (at 148.2 73.5 90) + (descr "Side push button (https://www.alps.com/prod/info/E/PDF/Tact/SurfaceMount/SKRT/SKRT.pdf)") + (tags "push horizontal SPST 1P1T") + (property "Reference" "SW_VOL_UP1" + (at 0 -2.7 90) (layer "F.SilkS") (hide yes) - (uuid "ffe59921-017a-4115-ae75-e7362858e013") + (uuid "9839ee46-3419-49d0-994f-650f9ba578ed") (effects (font (size 1 1) @@ -10819,10 +9708,10 @@ ) ) ) - (property "Value" "2.2µH" - (at 0 -3.1 180) + (property "Value" "SKRTLAE010" + (at 0 2.9 90) (layer "F.Fab") - (uuid "f7ed0b39-2bb6-4ac2-b130-2d4acdfc91d6") + (uuid "9999d58e-01f0-43e2-b018-b7e50a4c1924") (effects (font (size 1 1) @@ -10831,11 +9720,11 @@ ) ) (property "Datasheet" "" - (at 0 0 180) + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "3e4322a3-a35b-4e0b-a615-bb32b6a3b4de") + (uuid "4e440a3f-d87d-46dc-890e-f28154048a72") (effects (font (size 1.27 1.27) @@ -10843,12 +9732,12 @@ ) ) ) - (property "Description" "Inductor" - (at 0 0 180) + (property "Description" "Push button switch, generic, two pins" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "5fe6f736-15ca-4dab-af95-76963fd8932d") + (uuid "c64c023c-3ab6-430a-90ea-cfb2fe8ee4c6") (effects (font (size 1.27 1.27) @@ -10856,12 +9745,12 @@ ) ) ) - (property "MF" "Bourns" - (at 0 0 0) + (property "MF" "Alps Alpine" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "b61c9464-b7ff-4ead-994b-2430b0889606") + (uuid "7b4f443b-c100-48d3-94c3-98e5a6719dfd") (effects (font (size 1 1) @@ -10869,12 +9758,12 @@ ) ) ) - (property "Manufacturer_Part_Number" "SRN4018-2R2M" - (at 0 0 0) + (property "Manufacturer_Part_Number" "SKRTLAE010" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "0a5b33bb-be77-48af-818f-8d9552f16b33") + (uuid "964ffdfc-9262-49fd-bdc3-c84883ed669b") (effects (font (size 1 1) @@ -10882,12 +9771,12 @@ ) ) ) - (property "LCSC" "C913207" - (at 0 0 0) + (property "LCSC" "C110293" + (at 0 0 90) (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "676eb99d-d09a-4889-8cf8-b5da02a85f57") + (uuid "ffd33cf1-98bb-414a-bda5-3606035e9d1c") (effects (font (size 1 1) @@ -10895,34 +9784,31 @@ ) ) ) - (property "Stackup Path" "L_BUCK1" - (at 0 2 180) + (property "Stackup Path" "SW_VOL_UP1" + (at -2 0 0) (layer "F.SilkS") (hide yes) - (uuid "d138fa84-f404-44d2-8323-a9765612740a") + (uuid "e59e479e-a052-447e-817a-85437be2a307") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:49" - (at 0 2 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:89" + (at -2 0 0) (layer "F.SilkS") (hide yes) - (uuid "09d6870f-54ed-4e4a-a59c-7ba124534793") + (uuid "768d8ced-bdbf-4348-9245-5ac390719e45") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "Choke_* *Coil* Inductor_* L_*") - (path "/6ec4aba0-5ea6-53c2-98e5-0b6074e59f4d") + (path "/16c18574-76f3-5208-aa75-7f5df01a9092") (units (unit (name "A") @@ -10932,169 +9818,249 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start 2.385 2.11) - (end 2.385 1.085) + (start 2.4 -1.5) + (end 2.4 -0.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "2e837ce8-8a82-4459-9d15-84c9a79c31e3") + (uuid "3532fb2f-7360-447e-909a-9f3201b4a11a") ) (fp_line - (start 2.385 2.11) - (end 1.36 2.11) + (start 1.8 -1.5) + (end 2.4 -1.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "d6f89670-efa9-488c-8215-dd3da07234fe") + (uuid "8bbd44e6-28b2-40f1-8f6b-03b9fed009fd") ) (fp_line - (start 2.385 -2.11) - (end 2.385 -1.085) + (start -1.8 -1.5) + (end -2.4 -1.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "4167a84e-1424-4988-bce1-9a930b23a822") + (uuid "077d03f1-70b9-421e-9792-3109f0717f9b") ) (fp_line - (start 2.385 -2.11) - (end 1.36 -2.11) + (start -2.4 -1.5) + (end -2.4 -0.5) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "c90dc85a-046f-4c6f-b35a-c1f6fa814167") + (uuid "f93fa75d-8fd6-45d4-a0e9-34fa790f7f59") ) (fp_line - (start -2.385 2.11) - (end -1.36 2.11) + (start -1 1.3) + (end 1 1.3) (stroke (width 0.12) (type solid) ) (layer "F.SilkS") - (uuid "64236419-60f3-4cf7-b820-8960bc28c105") + (uuid "614d9da3-c760-4258-9480-7a6b8ca9d981") ) (fp_line - (start -2.385 2.11) - (end -2.385 1.085) + (start 1 0.3) + (end -1 0.3) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "F.SilkS") - (uuid "fa1e96ca-d6fc-42cc-a0b4-554c579387e1") + (layer "Dwgs.User") + (uuid "3624ac8e-e909-4cd1-9a84-481c5e59d3e8") ) (fp_line - (start -2.385 -2.11) - (end -1.36 -2.11) + (start -1 0.3) + (end -1 1.5) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "F.SilkS") - (uuid "c172ea71-ff50-4d12-b7e5-d3271a6d8b6f") + (layer "Dwgs.User") + (uuid "f1174bf9-799f-4904-9d4b-ae6fe5610c52") ) (fp_line - (start -2.385 -2.11) - (end -2.385 -1.085) + (start 1 1.5) + (end 1 0.3) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "F.SilkS") - (uuid "000e7df3-b262-457b-b983-b9875b78ae37") + (layer "Dwgs.User") + (uuid "0197f2b1-f3ce-47c9-9a44-701326c82ac4") ) (fp_line - (start 2.53 -2.25) - (end 2.53 2.25) + (start 0.5 1.5) + (end 1 0.3) + (stroke + (width 0.1) + (type solid) + ) + (layer "Dwgs.User") + (uuid "b586b234-cdf5-4781-8281-4441cba3a17d") + ) + (fp_line + (start 0 1.5) + (end 0.5 0.3) + (stroke + (width 0.1) + (type solid) + ) + (layer "Dwgs.User") + (uuid "29f6286a-4559-4b84-b5df-751be9c4d4fe") + ) + (fp_line + (start -0.5 1.5) + (end 0 0.3) + (stroke + (width 0.1) + (type solid) + ) + (layer "Dwgs.User") + (uuid "d17368d1-194d-4325-8f38-e2874ae799e5") + ) + (fp_line + (start -1 1.5) + (end -0.5 0.3) + (stroke + (width 0.1) + (type solid) + ) + (layer "Dwgs.User") + (uuid "a4d5077c-80f1-4170-8719-eaa52cb3c538") + ) + (fp_line + (start -1 1.5) + (end 1 1.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "Dwgs.User") + (uuid "d37d28af-1edc-4505-b940-24d25c2d3244") + ) + (fp_line + (start 2.83 -2.05) + (end 2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "3415a2c0-31ae-4970-8b32-647dc008fe5e") + (uuid "32ed1cb7-60bc-4c7a-9cbc-ae9ab60f399a") ) (fp_line - (start -2.53 2.25) - (end 2.53 2.25) + (start -2.83 -2.05) + (end 2.83 -2.05) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "5c0ce237-f627-4b79-9010-c4132e503904") + (uuid "8736558a-8534-4b72-8847-211f6f660b52") ) (fp_line - (start -2.53 -2.25) - (end 2.53 -2.25) + (start -2.83 -2.05) + (end -2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "eb9a644d-dbd7-4137-ac95-3377b5df40c5") + (uuid "eeddff91-f54c-4330-86e7-408a7702185e") ) (fp_line - (start -2.53 -2.25) - (end -2.53 2.25) + (start -2.83 2.3) + (end 2.83 2.3) (stroke (width 0.05) (type solid) ) (layer "F.CrtYd") - (uuid "e45e72e9-9663-4966-a3b0-915b5735dbdf") + (uuid "28ae4f09-2c6e-40f7-a922-17ec558c3922") ) (fp_line - (start 2 2) - (end -2 2) + (start 2.25 -1.35) + (end 2.25 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "2b896796-9e14-4e04-851d-d2d2c11795c3") + (uuid "cfcbb8da-b025-43fb-9188-13fa26de2339") ) (fp_line - (start 2 -2) - (end 2 2) + (start -2.25 -1.35) + (end 2.25 -1.35) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "ba87e1e8-2ad5-4e1d-9bb0-02789d9ff863") + (uuid "70a0119c-5749-464b-9c6a-0676cb3805b2") ) (fp_line - (start -2 -2) - (end 2 -2) + (start -2.25 -1.35) + (end -2.25 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "6c67d810-95af-4689-8a4c-dbaeb9db7ce5") + (uuid "4a22c671-2b68-4ded-a34c-8dad12f0a0dc") ) (fp_line - (start -2 -2) - (end -2 2) + (start -2.25 1.21) + (end 2.25 1.21) (stroke (width 0.1) (type solid) ) (layer "F.Fab") - (uuid "f3dd3898-1b08-4bd0-9f5e-43cc6b91136f") + (uuid "4ba6f573-2330-49fd-81e2-ddefe1158c0d") + ) + (fp_line + (start 1 2.04) + (end 1 1.21) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "71015b5f-d635-4d3c-9206-7e6d18f7ce11") + ) + (fp_line + (start -1 2.04) + (end -1 1.21) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "e6e93c5b-3672-428f-aa09-6850738df417") + ) + (fp_line + (start -1 2.04) + (end 1 2.04) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "8c7561a0-d3bd-4734-91d1-90a80b7cfc19") ) (fp_text user "${REFERENCE}" - (at 0 0 180) + (at 0 0 90) (layer "F.Fab") - (uuid "a4c89381-5a1a-41ea-9ea5-7d9485e3ffc9") + (uuid "494a6678-ec75-40e3-8622-94cb6628936f") (effects (font (size 1 1) @@ -11102,26 +10068,66 @@ ) ) ) - (pad "1" smd rect - (at -1.525 0 180) - (size 1.5 3.6) + (pad "" np_thru_hole circle + (at -2.125 0 90) + (size 0.9 0.9) + (drill 0.9) + (layers "*.Cu" "*.Mask") + (uuid "810ba315-1fe7-4937-a998-19577bf16814") + ) + (pad "" np_thru_hole circle + (at 2.125 0 90) + (size 0.9 0.9) + (drill 0.9) + (layers "*.Cu" "*.Mask") + (uuid "4d009025-50cf-44b1-a3be-a4c9c8cb3dd2") + ) + (pad "1" smd roundrect + (at -1.225 -0.9 90) + (size 0.75 1.8) (layers "F.Cu" "F.Mask" "F.Paste") - (net "/Power_Buck/BUCK_SW") + (roundrect_rratio 0.25) + (net "/Buttons_Direct/BTN_VOL_UP") (pinfunction "1_1") (pintype "passive") - (uuid "636579c2-3a8e-4eee-a8cf-ae2dd9018b0d") + (uuid "1963b1bd-85af-4149-98cc-621d3f3e4363") ) - (pad "2" smd rect - (at 1.525 0 180) - (size 1.5 3.6) + (pad "1" smd roundrect + (at 1.225 -0.9 90) + (size 0.75 1.8) (layers "F.Cu" "F.Mask" "F.Paste") - (net "3V3") + (roundrect_rratio 0.25) + (net "/Buttons_Direct/BTN_VOL_UP") + (pinfunction "1_1") + (pintype "passive") + (uuid "73f29954-949f-4a50-9b34-4946a9cf28da") + ) + (pad "2" smd roundrect + (at 0 -0.9 90) + (size 0.6 1.8) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "GND") (pinfunction "2_2") (pintype "passive") - (uuid "92ef3bbf-544e-448a-b98e-6c61e1cbdb73") + (uuid "4465281e-bf89-46b3-928f-e416edf2488d") + ) + (pad "MP" smd roundrect + (at -1.85 1.05 90) + (size 1.3 0.9) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (uuid "3fae3e4d-f8c7-4f3e-94ce-af13138b5d7a") + ) + (pad "MP" smd roundrect + (at 1.85 1.05 90) + (size 1.3 0.9) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (uuid "69939839-9a6a-40a8-9b1c-2abe43824a62") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Inductor_SMD.3dshapes/L_Bourns-SRN4018.step" + (model "${KIPRJMOD}/libraries/3dmodels/SW_Alps_SKRTLAE010.step" (offset (xyz 0 0 0) ) @@ -11197,6 +10203,215 @@ ) (embedded_fonts no) ) + (footprint "Resistor_SMD:R_0402_1005Metric" + (placed yes) + (layer "F.Cu") + (uuid "e8959995-a97b-490a-9489-b4f7b64be06d") + (at 130 103.4 -90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_VSYS2" + (at 0 -1.17 90) + (layer "F.SilkS") + (hide yes) + (uuid "0b3faf92-5a7b-4bfe-a707-6604feb3c41d") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Value" "100kΩ" + (at 0 1.17 90) + (layer "F.Fab") + (uuid "288ac433-61e6-4fc6-9274-c54484190a7f") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Datasheet" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "9379bbc4-c850-40b3-a297-3a28f60aa6e2") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "Description" "Resistor" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "03ed0427-d518-450b-b16d-8be4a7859703") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 270) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "49a168d6-6a16-44c6-a545-f8ef17c5daec") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Manufacturer_Part_Number" "0402WGF1003TCE" + (at 0 0 270) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "3a4332bb-dd49-4d26-b933-0fca5656a7d2") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "LCSC" "C25741" + (at 0 0 270) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "52bd1ce5-0fd0-4bf8-b601-ed44e4f002b9") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "R_VSYS2" + (at 0 -2 90) + (layer "F.SilkS") + (hide yes) + (uuid "5273a233-f6d0-41bd-acab-632e700840b1") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:76" + (at 0 -2 90) + (layer "F.SilkS") + (hide yes) + (uuid "c80f382d-f2fc-43fc-bfc9-fc9d1a75d374") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "R_*") + (path "/d2b6c4ab-7ef9-5ded-a5d1-4d96c799220d") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.153641 0.38) + (end 0.153641 0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "ce95fb31-55e2-4591-9bd2-8ae8f6d43a06") + ) + (fp_line + (start -0.153641 -0.38) + (end 0.153641 -0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "525f7d00-5b79-40fd-900a-9c127f65144b") + ) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "F.CrtYd") + (uuid "97779d48-9cf1-4da8-af97-9422048a50e0") + ) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "F.Fab") + (uuid "33e48ea9-8f9c-41f1-bb69-5ab5ca003079") + ) + (fp_text user "${REFERENCE}" + (at 0 0 90) + (layer "F.Fab") + (uuid "71bb2df3-ddee-4fb1-9819-3e26a316104a") + (effects + (font + (size 0.26 0.26) + (thickness 0.04) + ) + ) + ) + (pad "1" smd roundrect + (at -0.51 0 270) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/MCU_Core/VSYS_SENSE") + (pintype "passive") + (uuid "5340ee3b-7dcb-46b9-8fc3-914353e92958") + ) + (pad "2" smd roundrect + (at 0.51 0 270) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "9cbed9b8-2158-4afd-b90d-1503edc590f7") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) (footprint "Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010" (layer "F.Cu") (uuid "f2cbf9f4-07f1-46eb-8aff-c996a68f2223") @@ -11207,7 +10422,7 @@ (at 0 -2.7 180) (layer "F.SilkS") (hide yes) - (uuid "63853dc8-253d-4ee3-890d-81a26c7051ec") + (uuid "8449f17a-bfbf-4f65-b209-bf534f8d4283") (effects (font (size 1 1) @@ -11218,7 +10433,7 @@ (property "Value" "SKRTLAE010" (at 0 2.9 0) (layer "F.Fab") - (uuid "2f4f4acc-c522-4a0b-be7d-7c1114273030") + (uuid "2611e36b-7d64-4a1d-9d0c-bdbd4c1d16d8") (effects (font (size 1 1) @@ -11231,7 +10446,7 @@ (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "131f38b0-75f5-4584-afa2-c904bf81fe01") + (uuid "91c7fc28-3b14-4dcd-91c3-c04f3242edad") (effects (font (size 1.27 1.27) @@ -11244,7 +10459,7 @@ (unlocked yes) (layer "F.Fab") (hide yes) - (uuid "30a4970b-0b8b-4396-86e5-841d62fb7933") + (uuid "e4114fa7-5aef-4fe7-9bf1-c0a157d057f9") (effects (font (size 1.27 1.27) @@ -11303,7 +10518,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:81" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:84" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -11753,6 +10968,214 @@ ) (embedded_fonts no) ) + (footprint "R_0402_1005Metric" + (layer "F.Cu") + (uuid "f64b9c26-968b-465d-a27e-51c4731c2e17") + (at 128.02 116.4 90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_USB_DP1" + (at 0 -1.17 90) + (layer "F.SilkS") + (hide yes) + (uuid "90501240-a68b-4189-9bf1-0a5b73f7e19e") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Value" "27Ω" + (at 0 1.17 90) + (layer "F.Fab") + (uuid "2f240631-61f7-4e90-964f-8ef0c35a88b5") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Datasheet" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "06342202-0c71-4215-9c58-18796ba6ece3") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "Description" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "e6cf46b8-517f-4438-8caa-94813ab378cb") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 90) + (layer "F.SilkS") + (hide yes) + (uuid "fc3920be-f73c-4782-94ac-70341ca7a99d") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "MF" "Yageo" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "e310aa29-d135-42e4-a148-71b8a4dedc28") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Manufacturer_Part_Number" "RC0402FR-0727RL" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "ec61fd03-29c3-4e6d-a884-255000c83edc") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "LCSC" "C138021" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "e2fe421a-d391-48ad-9a45-ac3671ca8cf8") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "R_USB_DP1" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "04aaf088-8694-4dd1-afe5-48d59eab6b10") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:73" + (at 0 2 90) + (layer "F.SilkS") + (hide yes) + (uuid "cf15ba84-a2ba-4c6c-91ef-c5987047cf6e") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (path "/5ae28961-4dde-5c49-9b7d-1813cc7efa56") + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.153641 -0.38) + (end 0.153641 -0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "bf070693-1321-4642-a1c8-7e22fd90225a") + ) + (fp_line + (start -0.153641 0.38) + (end 0.153641 0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "F.SilkS") + (uuid "c3f58714-ed6d-4d33-b693-1cc77b2e71b4") + ) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "F.CrtYd") + (uuid "fe574809-90a5-437b-a69a-1321305be4e7") + ) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "F.Fab") + (uuid "a174884c-22db-4340-8a9f-324cf6d62628") + ) + (fp_text user "${REFERENCE}" + (at 0 0 90) + (layer "F.Fab") + (uuid "0d173c4a-6328-48a9-9dbd-f02801fbe0d9") + (effects + (font + (size 0.26 0.26) + (thickness 0.04) + ) + ) + ) + (pad "1" smd roundrect + (at -0.51 0 90) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/MCU_Core/USB_DP") + (uuid "04d4e4e6-0331-4af2-9630-077bb92c194e") + ) + (pad "2" smd roundrect + (at 0.51 0 90) + (size 0.54 0.64) + (layers "F.Cu" "F.Mask" "F.Paste") + (roundrect_rratio 0.25) + (net "/MCU_Core/USB_DP_MCU") + (uuid "b0903879-3c27-4ce4-8641-ba7595006690") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) (footprint "SW_Alps_SKRP" (layer "F.Cu") (uuid "f8890d13-d25d-4e1a-ad12-4601cadcf523") @@ -11856,7 +11279,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:79" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:82" (at 0 2 0) (layer "F.SilkS") (hide yes) @@ -12035,85 +11458,293 @@ (start 2.1 -1.6) (end -2.1 -1.6) (stroke - (width 0.1) + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "f1f31a66-288c-4e0b-b21c-da3c90530556") + ) + (fp_line + (start 2.1 1.6) + (end 2.1 -1.6) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "07b97827-c5a2-48a7-9e73-1bae76ba762b") + ) + (fp_arc + (start -0.4 1.1) + (mid -1.5 0) + (end -0.4 -1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "0d6eee0e-0471-4951-b3a4-dea2b2c397d8") + ) + (fp_arc + (start 0.4 -1.1) + (mid 1.5 0) + (end 0.4 1.1) + (stroke + (width 0.1) + (type solid) + ) + (layer "F.Fab") + (uuid "90f3ad72-9ef1-4f8f-be0d-4104072de479") + ) + (fp_text user "${REFERENCE}" + (at 0 0 0) + (layer "F.Fab") + (uuid "6703f257-580c-4416-9bb6-ec5a9e6b9b93") + (effects + (font + (size 0.6 0.6) + (thickness 0.09) + ) + ) + ) + (pad "1" smd rect + (at -2.075 -1.075) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "6a3188ee-7504-4fdf-ab10-4998ebbebbb6") + ) + (pad "1" smd rect + (at 2.075 -1.075) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "ce2cda9f-4dc1-4bcf-bf10-be3bf6208cc6") + ) + (pad "2" smd rect + (at -2.075 1.075) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "8e4bcfb5-521d-4464-81ac-bf385e626faa") + ) + (pad "2" smd rect + (at 2.075 1.075) + (size 1.05 0.65) + (layers "F.Cu" "F.Mask" "F.Paste") + (net "GND") + (uuid "0dabb405-1f44-4e89-a242-e2d0932d3e49") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Button_Switch_SMD.3dshapes/SW_SPST_PTS810.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) + (footprint "Resistor_SMD:R_0402_1005Metric" + (layer "F.Cu") + (uuid "feb5b6c7-c0e2-4640-90e3-610986db5ece") + (at 145.8 109.41 90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_BOOT_PU1" + (at 0 -1.17 90) + (layer "F.SilkS") + (hide yes) + (uuid "31d329d8-e856-48f5-b21f-e8b8e112298a") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Value" "10kΩ" + (at 0 1.17 90) + (layer "F.Fab") + (uuid "cc583e60-2a44-4941-ac9a-442fc869332b") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Datasheet" "" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "e0f41ae2-a612-4ecb-8910-bc3bcdbfc9e8") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "Description" "Resistor" + (at 0 0 90) + (layer "F.Fab") + (hide yes) + (uuid "95318fe0-1939-4a96-82bb-496eb372b979") + (effects + (font + (size 1.27 1.27) + ) + ) + ) + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "f3cc76e9-b47f-49b6-abe7-24850ee08854") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Manufacturer_Part_Number" "0402WGF1002TCE" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "5d4bab60-8ee2-4e4e-986b-3320d6c2829f") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "LCSC" "C25744" + (at 0 0 90) + (unlocked yes) + (layer "F.Fab") + (hide yes) + (uuid "4509dd1f-bafc-48fb-b332-54d7e413e331") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + ) + ) + (property "Stackup Path" "R_BOOT_PU1" + (at 2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "f3d3e6c1-4bc9-4b68-9204-80b16a8d2ce6") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:55" + (at 2 0 0) + (layer "F.SilkS") + (hide yes) + (uuid "5ff8f76a-e48e-468b-b6b8-9c08a8f10518") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "R_*") + (path "/458f2090-917f-58d0-aed4-6553732ff17f") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.153641 -0.38) + (end 0.153641 -0.38) + (stroke + (width 0.12) (type solid) ) - (layer "F.Fab") - (uuid "f1f31a66-288c-4e0b-b21c-da3c90530556") + (layer "F.SilkS") + (uuid "8f49ea27-b944-4326-904d-57603b45e24d") ) (fp_line - (start 2.1 1.6) - (end 2.1 -1.6) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke - (width 0.1) + (width 0.12) (type solid) ) - (layer "F.Fab") - (uuid "07b97827-c5a2-48a7-9e73-1bae76ba762b") + (layer "F.SilkS") + (uuid "f869a1aa-2cbf-43b0-b997-f12524de0b07") ) - (fp_arc - (start -0.4 1.1) - (mid -1.5 0) - (end -0.4 -1.1) + (fp_rect + (start -0.93 -0.47) + (end 0.93 0.47) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "F.Fab") - (uuid "0d6eee0e-0471-4951-b3a4-dea2b2c397d8") + (fill no) + (layer "F.CrtYd") + (uuid "1f236e61-f049-4f06-a913-acb12aa6fa14") ) - (fp_arc - (start 0.4 -1.1) - (mid 1.5 0) - (end 0.4 1.1) + (fp_rect + (start -0.525 -0.27) + (end 0.525 0.27) (stroke (width 0.1) (type solid) ) + (fill no) (layer "F.Fab") - (uuid "90f3ad72-9ef1-4f8f-be0d-4104072de479") + (uuid "d940bf26-785c-421d-8a0f-5e90931d506b") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 90) (layer "F.Fab") - (uuid "6703f257-580c-4416-9bb6-ec5a9e6b9b93") + (uuid "647dffde-a817-4181-a9eb-19e0871bb307") (effects (font - (size 0.6 0.6) - (thickness 0.09) + (size 0.26 0.26) + (thickness 0.04) ) ) ) - (pad "1" smd rect - (at -2.075 -1.075) - (size 1.05 0.65) - (layers "F.Cu" "F.Mask" "F.Paste") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "6a3188ee-7504-4fdf-ab10-4998ebbebbb6") - ) - (pad "1" smd rect - (at 2.075 -1.075) - (size 1.05 0.65) - (layers "F.Cu" "F.Mask" "F.Paste") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "ce2cda9f-4dc1-4bcf-bf10-be3bf6208cc6") - ) - (pad "2" smd rect - (at -2.075 1.075) - (size 1.05 0.65) + (pad "1" smd roundrect + (at -0.51 0 90) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") - (net "GND") - (uuid "8e4bcfb5-521d-4464-81ac-bf385e626faa") + (roundrect_rratio 0.25) + (net "/MCU_Core/MCU_BOOT") + (pintype "passive") + (uuid "8f32a9e7-08e3-47c6-8991-e685d0e80089") ) - (pad "2" smd rect - (at 2.075 1.075) - (size 1.05 0.65) + (pad "2" smd roundrect + (at 0.51 0 90) + (size 0.54 0.64) (layers "F.Cu" "F.Mask" "F.Paste") - (net "GND") - (uuid "0dabb405-1f44-4e89-a242-e2d0932d3e49") + (roundrect_rratio 0.25) + (net "3V3") + (pintype "passive") + (uuid "22fafb5e-bada-49fb-9067-3b8e4ed0d64d") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Button_Switch_SMD.3dshapes/SW_SPST_PTS810.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -12126,123 +11757,128 @@ ) ) (footprint "Resistor_SMD:R_0402_1005Metric" - (layer "F.Cu") - (uuid "fe714753-d6dd-4d04-897d-7cd5f5f5827a") - (at 122.26 114.5 180) + (layer "B.Cu") + (uuid "011f24df-42a2-4eec-a509-7f958fc38598") + (at 126.87125 93.764999 180) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_TS1" - (at 0 -1.17 180) - (layer "F.SilkS") + (property "Reference" "R_BTN_PU1" + (at 0 1.17 0) + (layer "B.SilkS") (hide yes) - (uuid "a453dd30-5a2a-44c4-a880-818306b9a912") + (uuid "d642e40c-8ac8-4139-be94-bc6439b199f4") (effects (font (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "Value" "10kΩ" - (at 0 1.17 180) - (layer "F.Fab") - (uuid "38311a83-d968-43a5-b963-3f4b048ffe57") + (property "Value" "100kΩ" + (at 0 -1.17 0) + (layer "B.Fab") + (uuid "d998a7f1-e267-4bf5-8104-2bcd8cf3de43") (effects (font (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) (property "Datasheet" "" - (at 0 0 180) - (layer "F.Fab") + (at 0 0 0) + (layer "B.Fab") (hide yes) - (uuid "b626d0d2-b116-410b-b877-ce4a93ceda2b") + (uuid "b2515333-ec4a-41c6-80f3-35fe42fe45e0") (effects (font (size 1.27 1.27) ) + (justify mirror) ) ) (property "Description" "Resistor" - (at 0 0 180) - (layer "F.Fab") + (at 0 0 0) + (layer "B.Fab") (hide yes) - (uuid "8031d0c6-9cf6-48ae-a7b5-2cc5b5efe364") + (uuid "e1b7fa0c-a113-45f5-b870-dad88e2b166f") (effects (font (size 1.27 1.27) ) + (justify mirror) ) ) (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 0) + (at 0 0 180) (unlocked yes) - (layer "F.Fab") + (layer "B.Fab") (hide yes) - (uuid "3c84c8f9-6671-4a55-b309-d44dbab736e3") + (uuid "4bc4cc8b-4a5a-47a0-b5f0-1d2a41f63460") (effects (font (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF1002TCE" - (at 0 0 0) + (property "Manufacturer_Part_Number" "0402WGF1003TCE" + (at 0 0 180) (unlocked yes) - (layer "F.Fab") + (layer "B.Fab") (hide yes) - (uuid "9a085838-8dc1-45ec-a649-e19d6bdc87c1") + (uuid "94163f3f-906f-4a13-89af-da01d43ad190") (effects (font (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "LCSC" "C25744" - (at 0 0 0) + (property "LCSC" "C25741" + (at 0 0 180) (unlocked yes) - (layer "F.Fab") + (layer "B.Fab") (hide yes) - (uuid "ddb9cc9d-b7d3-4699-9670-75f91179c8d1") + (uuid "3665d71f-8b0c-49f8-b01d-b2ad8a7fefbb") (effects (font (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "Stackup Path" "R_TS1" - (at 0 2 180) - (layer "F.SilkS") + (property "Stackup Path" "R_BTN_PU1" + (at 0 -2 0) + (layer "B.SilkS") (hide yes) - (uuid "d88ed2b2-a397-4355-b282-27f49ec99d2b") + (uuid "850b33eb-4787-4f11-bf95-e377645343f8") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:68" - (at 0 2 180) - (layer "F.SilkS") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:56" + (at 0 -2 0) + (layer "B.SilkS") (hide yes) - (uuid "be24c03a-6f38-4cf0-9939-c074181dbb1a") + (uuid "b6d2bf93-ccee-4136-a8bd-a91ef2eb1114") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) (property ki_fp_filters "R_*") - (path "/f8467960-077e-5dfa-ad5f-583d827e1496") + (path "/2c7802cf-9133-5dcc-a7ea-5198e1afda3a") (units (unit (name "A") @@ -12258,8 +11894,8 @@ (width 0.12) (type solid) ) - (layer "F.SilkS") - (uuid "bba4ce97-f66d-4840-aa22-478584dc2ece") + (layer "B.SilkS") + (uuid "68d01d87-3099-4f37-94be-9886d9225d07") ) (fp_line (start -0.153641 -0.38) @@ -12268,59 +11904,60 @@ (width 0.12) (type solid) ) - (layer "F.SilkS") - (uuid "f66a0c43-8a90-421f-942d-79424dd79a66") + (layer "B.SilkS") + (uuid "e61cc02e-a63e-4d39-9bbd-c137f8a4c5f7") ) (fp_rect - (start -0.93 -0.47) - (end 0.93 0.47) + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) (fill no) - (layer "F.CrtYd") - (uuid "fd4d52da-3502-473a-a0e7-4065cd5aa3e3") + (layer "B.CrtYd") + (uuid "6054914c-cace-476f-89de-68107d4ff345") ) (fp_rect - (start -0.525 -0.27) - (end 0.525 0.27) + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) (fill no) - (layer "F.Fab") - (uuid "29f7db3e-c537-498a-9c16-764d72295de9") + (layer "B.Fab") + (uuid "6eea64be-1729-4d99-a357-18c93fee9e05") ) (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "F.Fab") - (uuid "aaf3dfbe-42d4-4dd0-8e3f-6495cec0f440") + (at 0 0 0) + (layer "B.Fab") + (uuid "8667ece4-d0d6-4c97-acf0-9b388c7d4825") (effects (font (size 0.26 0.26) (thickness 0.04) ) + (justify mirror) ) ) (pad "1" smd roundrect (at -0.51 0 180) (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") + (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Charger/CHG_TS") + (net "3V3") (pintype "passive") - (uuid "241f4cdd-9b3a-42aa-b258-efeef884ee02") + (uuid "c6d55744-4f81-474b-9493-5496c662a32a") ) (pad "2" smd roundrect (at 0.51 0 180) (size 0.54 0.64) - (layers "F.Cu" "F.Mask" "F.Paste") + (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "GND") + (net "/MCU_Core/PWR_BTN_SENSE") (pintype "passive") - (uuid "5a566ea4-933f-4c3e-aaad-12f462eee6a7") + (uuid "9366c0e9-4e48-477e-a307-e1b7995c16d9") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -12335,17 +11972,17 @@ ) ) ) - (footprint "Resistor_SMD:R_0402_1005Metric" + (footprint "Capacitor_SMD:C_0805_2012Metric" (layer "B.Cu") - (uuid "011f24df-42a2-4eec-a509-7f958fc38598") - (at 125.41 94.6) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_BTN_PU1" - (at 0 1.17 180) + (uuid "0390cbd8-aad5-4513-8815-b8e8b89441b2") + (at 134.7 94.25) + (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (tags "capacitor") + (property "Reference" "C_SYS_1" + (at 0 1.68 180) (layer "B.SilkS") (hide yes) - (uuid "d642e40c-8ac8-4139-be94-bc6439b199f4") + (uuid "462f5cf9-ee6a-49e3-9d91-19a8f95e4c99") (effects (font (size 1 1) @@ -12354,10 +11991,10 @@ (justify mirror) ) ) - (property "Value" "100kΩ" - (at 0 -1.17 180) + (property "Value" "10µF" + (at 0 -1.68 180) (layer "B.Fab") - (uuid "d998a7f1-e267-4bf5-8104-2bcd8cf3de43") + (uuid "f6dd34e2-1a7e-4242-a613-075d419820ea") (effects (font (size 1 1) @@ -12370,7 +12007,7 @@ (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "b2515333-ec4a-41c6-80f3-35fe42fe45e0") + (uuid "a54cd415-70da-4145-b792-a42b1cfdb01d") (effects (font (size 1.27 1.27) @@ -12378,11 +12015,11 @@ (justify mirror) ) ) - (property "Description" "Resistor" + (property "Description" "Unpolarized capacitor" (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "e1b7fa0c-a113-45f5-b870-dad88e2b166f") + (uuid "476d8b11-b125-486f-abc1-e1acb2df385e") (effects (font (size 1.27 1.27) @@ -12390,12 +12027,12 @@ (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (property "MF" "Samsung Electro-Mechanics" (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "4bc4cc8b-4a5a-47a0-b5f0-1d2a41f63460") + (uuid "f2cd291d-80fe-4e7c-bcd6-0a18265538aa") (effects (font (size 1 1) @@ -12404,12 +12041,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF1003TCE" + (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "94163f3f-906f-4a13-89af-da01d43ad190") + (uuid "962c8b77-9f33-489f-ba7c-17cda90821a8") (effects (font (size 1 1) @@ -12418,12 +12055,12 @@ (justify mirror) ) ) - (property "LCSC" "C25741" + (property "LCSC" "C15850" (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "3665d71f-8b0c-49f8-b01d-b2ad8a7fefbb") + (uuid "dfc0e204-27b5-4747-b51b-e7acd18a4832") (effects (font (size 1 1) @@ -12432,11 +12069,11 @@ (justify mirror) ) ) - (property "Stackup Path" "R_BTN_PU1" - (at 0 -2 180) + (property "Stackup Path" "C_SYS_1" + (at 0 2 180) (layer "B.SilkS") (hide yes) - (uuid "850b33eb-4787-4f11-bf95-e377645343f8") + (uuid "30080745-879b-4733-a974-11c9086c8a99") (effects (font (size 1.27 1.27) @@ -12444,11 +12081,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:54" - (at 0 -2 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:38" + (at 0 2 180) (layer "B.SilkS") (hide yes) - (uuid "b6d2bf93-ccee-4136-a8bd-a91ef2eb1114") + (uuid "5ec1c961-646b-438f-b18b-04ad86600ba0") (effects (font (size 1.27 1.27) @@ -12456,8 +12093,8 @@ ) ) ) - (property ki_fp_filters "R_*") - (path "/2c7802cf-9133-5dcc-a7ea-5198e1afda3a") + (property ki_fp_filters "C_*") + (path "/2d079967-45b0-53cc-b8e7-a89bd1adba7c") (units (unit (name "A") @@ -12467,79 +12104,79 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.261252 -0.735) + (end 0.261252 -0.735) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "e61cc02e-a63e-4d39-9bbd-c137f8a4c5f7") + (uuid "fd348c30-ac96-4b88-8e39-bcd0c5322995") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.261252 0.735) + (end 0.261252 0.735) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "68d01d87-3099-4f37-94be-9886d9225d07") + (uuid "b2ebadc8-9101-4e30-b021-c7888640bc5c") ) (fp_rect - (start -0.93 0.47) - (end 0.93 -0.47) + (start -1.7 0.98) + (end 1.7 -0.98) (stroke (width 0.05) (type solid) ) (fill no) (layer "B.CrtYd") - (uuid "6054914c-cace-476f-89de-68107d4ff345") + (uuid "cdd72dd5-f290-4529-99b8-cc9d439360f9") ) (fp_rect - (start -0.525 0.27) - (end 0.525 -0.27) + (start -1 0.625) + (end 1 -0.625) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "6eea64be-1729-4d99-a357-18c93fee9e05") + (uuid "c79fe089-a387-47f3-ac61-f5b8ad8d6266") ) (fp_text user "${REFERENCE}" (at 0 0 180) (layer "B.Fab") - (uuid "8667ece4-d0d6-4c97-acf0-9b388c7d4825") + (uuid "7d6fb0c1-d49a-46c1-a6f3-5c455d3cdd7d") (effects (font - (size 0.26 0.26) - (thickness 0.04) + (size 0.5 0.5) + (thickness 0.08) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) + (at -0.95 0) + (size 1 1.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "3V3") + (net "VSYS") (pintype "passive") - (uuid "c6d55744-4f81-474b-9493-5496c662a32a") + (uuid "6889a83d-65de-48a9-8120-aa0cfb12d1a5") ) (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) + (at 0.95 0) + (size 1 1.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/PWR_BTN_SENSE") + (net "GND") (pintype "passive") - (uuid "9366c0e9-4e48-477e-a307-e1b7995c16d9") + (uuid "c03d2c4a-2e1f-468b-a9cd-ceeeafa06362") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" (offset (xyz 0 0 0) ) @@ -12660,7 +12297,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:52" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:54" (at 0 2 270) (layer "B.SilkS") (hide yes) @@ -12990,225 +12627,6 @@ ) ) ) - (footprint "C_0603_1608Metric" - (layer "B.Cu") - (uuid "044b2102-9ad5-4193-ba1e-1e087a73af62") - (at 140.5 88.75 90) - (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_VBUS1" - (at 0 1.43 270) - (layer "B.SilkS") - (hide yes) - (uuid "09d5ce34-0f98-4cf2-ae5b-468e8b6ee7da") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Value" "1µF" - (at 0 -1.43 270) - (layer "B.Fab") - (uuid "45c5cf89-b029-49c4-904f-8964c55c3e01") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Datasheet" "" - (at 0 0 270) - (layer "B.Fab") - (hide yes) - (uuid "311f3409-502e-4185-b6ab-84e5fad2e7ac") - (effects - (font - (size 1.27 1.27) - ) - (justify mirror) - ) - ) - (property "Description" "" - (at 0 0 270) - (layer "B.Fab") - (hide yes) - (uuid "2571f6ff-f934-4f98-ab15-cbbdebb0f0df") - (effects - (font - (size 1.27 1.27) - ) - (justify mirror) - ) - ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 270) - (layer "B.SilkS") - (hide yes) - (uuid "39e7a348-055d-4b94-952b-8f99259556d0") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "f16b69b8-d1f5-4771-8030-e2bc0e703de4") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Manufacturer_Part_Number" "CL10A105KB8NNNC" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "0905c7bd-a464-4610-8e58-fe666b9cb3e5") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "LCSC" "C15849" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "a139e07b-a645-48ca-9d9a-b0f945c0e686") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Path" "C_VBUS1" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "ddd78639-35d9-4316-a5d1-bd1013a73216") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:104" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "3abe8a40-6bc6-403c-8da2-5947b2bbb85b") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (path "/327a1356-1746-5126-af6b-2e11894dc926") - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.14058 -0.51) - (end 0.14058 -0.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "62788d7f-a96d-45bd-94f1-49a267a11f6b") - ) - (fp_line - (start -0.14058 0.51) - (end 0.14058 0.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "798af9ca-7d99-426b-9fa4-f005fb348ded") - ) - (fp_rect - (start -1.48 0.73) - (end 1.48 -0.73) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "B.CrtYd") - (uuid "6981a8fc-fe07-43ee-9d4d-b048460ec39b") - ) - (fp_rect - (start -0.8 0.4) - (end 0.8 -0.4) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "B.Fab") - (uuid "2f14ea55-ed5c-4a9b-ab59-0496495175be") - ) - (fp_text user "${REFERENCE}" - (at 0 0 270) - (layer "B.Fab") - (uuid "f0019067-874c-4aea-b197-3c89349abd17") - (effects - (font - (size 0.4 0.4) - (thickness 0.06) - ) - (justify mirror) - ) - ) - (pad "1" smd roundrect - (at -0.775 0 90) - (size 0.9 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "VBUS") - (uuid "44bb32ef-9bfa-4647-aae9-fcdf1e19fd2d") - ) - (pad "2" smd roundrect - (at 0.775 0 90) - (size 0.9 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "GND") - (uuid "b3dc0f43-9530-466b-9654-f3c663fdc7b2") - ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) (footprint "Diode_SMD:D_SOD-323" (layer "B.Cu") (uuid "09772b6b-3211-41df-89ed-dfcf40abfe06") @@ -13322,7 +12740,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:46" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:48" (at 2 0 90) (layer "B.SilkS") (hide yes) @@ -13885,441 +13303,161 @@ (fp_rect (start -2.45 1.85) (end 4.45 -6.75) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "B.CrtYd") - (uuid "92bdc1fd-8e45-423b-8c9d-5a993075237b") - ) - (fp_line - (start -1.95 -6.25) - (end 3.95 -6.25) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "d01955cd-fb4b-46c3-9873-4bb28a6d3a31") - ) - (fp_line - (start -1.95 1.35) - (end -1.95 -6.25) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "532255be-7b63-4120-bbb3-c9a0b9a354fa") - ) - (fp_line - (start -1.25 -0.25) - (end -1.25 1.35) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "3718e0c9-b3f7-41d7-b16b-239d0af2efc1") - ) - (fp_line - (start -1.25 1.35) - (end -1.95 1.35) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "d2d95edb-ecec-4e02-b8a1-f00ceef2758f") - ) - (fp_line - (start -0.5 -1.375) - (end 0.5 -1.375) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "202b3be6-5bd8-46e0-9a56-ed4ac79cb5e2") - ) - (fp_line - (start 0 -0.875) - (end -0.5 -1.375) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "f40f3b58-d303-4131-a66a-812d63188c47") - ) - (fp_line - (start 0.5 -1.375) - (end 0 -0.875) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "07e2a8d7-10e5-401e-b649-1a5de3350971") - ) - (fp_line - (start 3.25 -0.25) - (end -1.25 -0.25) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "a10732e1-5613-48ec-b93c-08a13ff9552f") - ) - (fp_line - (start 3.25 1.35) - (end 3.25 -0.25) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "06f57cc1-2306-4315-85c8-92b4454731c7") - ) - (fp_line - (start 3.95 -6.25) - (end 3.95 1.35) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "92f09775-f237-4396-8ca6-389d6ab4dbd2") - ) - (fp_line - (start 3.95 1.35) - (end 3.25 1.35) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "2ad816ad-be07-4045-8bdb-9816daa4e92b") - ) - (fp_text user "${REFERENCE}" - (at 1 -2.5 0) - (layer "B.Fab") - (uuid "2212344b-2601-4d9b-9bce-76c55d4e7849") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (pad "1" thru_hole roundrect - (at 0 0) - (size 1.2 1.75) - (drill 0.75) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (roundrect_rratio 0.208333) - (net "VBAT") - (pinfunction "Pin_1_1") - (pintype "passive") - (uuid "112d67c7-9867-4897-b940-8f89f29774ef") - ) - (pad "2" thru_hole oval - (at 2 0) - (size 1.2 1.75) - (drill 0.75) - (layers "*.Cu" "*.Mask") - (remove_unused_layers no) - (net "GND") - (pinfunction "Pin_2_2") - (pintype "passive") - (uuid "00b9c639-9b30-44d1-89bf-52d78b506a5d") - ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Connector_JST.3dshapes/JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) - (footprint "Fiducial:Fiducial_1mm_Mask2mm" - (layer "B.Cu") - (uuid "0dec0f0b-d272-4bdf-8fd7-124fee88a19c") - (at 145 61.75) - (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") - (tags "fiducial") - (property "Reference" "FID4" - (at 0 -1.95 0) - (layer "B.SilkS") - (hide yes) - (uuid "1329f56d-5590-46d9-bb36-0f11655b3d68") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Value" "Fiducial_1mm_Mask2mm" - (at 0 1.95 0) - (layer "B.Fab") - (hide yes) - (uuid "622e1404-8efa-4ca4-b735-1488041eee6e") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Datasheet" "" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "8c44d089-86d6-45cb-81eb-0eb33f9a9f05") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (property "Description" "" - (at 0 0 0) - (layer "F.Fab") - (hide yes) - (uuid "3271d475-04e0-4560-8cd5-cdafb0a0e862") - (effects - (font - (size 1.27 1.27) - ) - ) - ) - (attr smd board_only exclude_from_bom) - (duplicate_pad_numbers_are_jumpers no) - (pad "" smd circle - (at 0 0) - (size 1 1) - (layers "B.Cu" "B.Mask") - (solder_mask_margin 0.5) - (clearance 0.6) - (uuid "686ec435-e4c2-476a-a3ac-2b0f3966d08e") - ) - (embedded_fonts no) - ) - (footprint "C_0603_1608Metric" - (layer "B.Cu") - (uuid "13d92b51-f732-426d-ad79-903d065110d0") - (at 122.8 107.8 180) - (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_OLED_1" - (at 0 1.43 0) - (layer "B.SilkS") - (hide yes) - (uuid "abb02ee5-fdaf-4c79-b084-58baecf69712") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Value" "1µF" - (at 0 -1.43 0) - (layer "B.Fab") - (uuid "df2b867a-2937-413c-9eaf-f15fcc8ab729") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) + (stroke + (width 0.05) + (type solid) ) + (fill no) + (layer "B.CrtYd") + (uuid "92bdc1fd-8e45-423b-8c9d-5a993075237b") ) - (property "Datasheet" "" - (at 0 0 0) - (layer "B.Fab") - (hide yes) - (uuid "77565b82-0988-4b33-ba64-2b0385229649") - (effects - (font - (size 1.27 1.27) - ) - (justify mirror) + (fp_line + (start -1.95 -6.25) + (end 3.95 -6.25) + (stroke + (width 0.1) + (type solid) ) - ) - (property "Description" "" - (at 0 0 0) (layer "B.Fab") - (hide yes) - (uuid "be8ae1f0-8f7f-4002-9ccd-231556a23e8b") - (effects - (font - (size 1.27 1.27) - ) - (justify mirror) - ) + (uuid "d01955cd-fb4b-46c3-9873-4bb28a6d3a31") ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 0) - (layer "B.SilkS") - (hide yes) - (uuid "364e5dfc-2dcf-4328-811b-5a6a773167fd") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) + (fp_line + (start -1.95 1.35) + (end -1.95 -6.25) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "532255be-7b63-4120-bbb3-c9a0b9a354fa") ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "34d5dd0c-6e43-4ca6-9a84-ae2e84f4b00d") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) + (fp_line + (start -1.25 -0.25) + (end -1.25 1.35) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "3718e0c9-b3f7-41d7-b16b-239d0af2efc1") ) - (property "Manufacturer_Part_Number" "CL10A105KB8NNNC" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "30246e0a-d7e9-4184-9e02-8ab3ca676e3b") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) + (fp_line + (start -1.25 1.35) + (end -1.95 1.35) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "d2d95edb-ecec-4e02-b8a1-f00ceef2758f") ) - (property "LCSC" "C15849" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "0c475505-db17-42f0-ab73-e2342eceebc3") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) + (fp_line + (start -0.5 -1.375) + (end 0.5 -1.375) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "202b3be6-5bd8-46e0-9a56-ed4ac79cb5e2") ) - (property "Stackup Path" "C_OLED_1" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "0501c0f8-1495-484c-b599-9110ee6caa1e") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) + (fp_line + (start 0 -0.875) + (end -0.5 -1.375) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "f40f3b58-d303-4131-a66a-812d63188c47") ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:32" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "ccaff32f-e0fd-4c53-bc18-41b8246fe057") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) + (fp_line + (start 0.5 -1.375) + (end 0 -0.875) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "07e2a8d7-10e5-401e-b649-1a5de3350971") ) - (path "/722d9e65-c2cb-5466-b845-abde86ab0018") - (attr smd) - (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.14058 0.51) - (end 0.14058 0.51) + (start 3.25 -0.25) + (end -1.25 -0.25) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "B.SilkS") - (uuid "68091d5d-ec6a-4231-9ece-49be3d1b812f") + (layer "B.Fab") + (uuid "a10732e1-5613-48ec-b93c-08a13ff9552f") ) (fp_line - (start -0.14058 -0.51) - (end 0.14058 -0.51) + (start 3.25 1.35) + (end 3.25 -0.25) (stroke - (width 0.12) + (width 0.1) (type solid) ) - (layer "B.SilkS") - (uuid "fed99db1-b465-4259-bb29-5465d35775d7") + (layer "B.Fab") + (uuid "06f57cc1-2306-4315-85c8-92b4454731c7") ) - (fp_rect - (start -1.48 0.73) - (end 1.48 -0.73) + (fp_line + (start 3.95 -6.25) + (end 3.95 1.35) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (fill no) - (layer "B.CrtYd") - (uuid "eb0146bb-2154-4347-a987-b18accfd0220") + (layer "B.Fab") + (uuid "92f09775-f237-4396-8ca6-389d6ab4dbd2") ) - (fp_rect - (start -0.8 0.4) - (end 0.8 -0.4) + (fp_line + (start 3.95 1.35) + (end 3.25 1.35) (stroke (width 0.1) (type solid) ) - (fill no) (layer "B.Fab") - (uuid "dbbef132-57de-4fbe-a38a-741c29076ce1") + (uuid "2ad816ad-be07-4045-8bdb-9816daa4e92b") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 1 -2.5 0) (layer "B.Fab") - (uuid "a1120d2c-b5d6-4a71-9fa7-d9e14d47c122") + (uuid "2212344b-2601-4d9b-9bce-76c55d4e7849") (effects (font - (size 0.4 0.4) - (thickness 0.06) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (pad "1" smd roundrect - (at -0.775 0 180) - (size 0.9 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "3V3") - (uuid "7139f714-8c4a-475b-866b-b092fb48473f") + (pad "1" thru_hole roundrect + (at 0 0) + (size 1.2 1.75) + (drill 0.75) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) + (roundrect_rratio 0.208333) + (net "VBAT") + (pinfunction "Pin_1_1") + (pintype "passive") + (uuid "112d67c7-9867-4897-b940-8f89f29774ef") ) - (pad "2" smd roundrect - (at 0.775 0 180) - (size 0.9 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) + (pad "2" thru_hole oval + (at 2 0) + (size 1.2 1.75) + (drill 0.75) + (layers "*.Cu" "*.Mask") + (remove_unused_layers no) (net "GND") - (uuid "17ed6ea4-3ee6-40a3-a2b3-81d30f826739") + (pinfunction "Pin_2_2") + (pintype "passive") + (uuid "00b9c639-9b30-44d1-89bf-52d78b506a5d") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Connector_JST.3dshapes/JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal.step" (offset (xyz 0 0 0) ) @@ -14333,15 +13471,15 @@ ) (footprint "Fiducial:Fiducial_1mm_Mask2mm" (layer "B.Cu") - (uuid "1eed4b54-beb5-4c1a-8345-3ed6feafa395") - (at 144.5 128.25) + (uuid "0dec0f0b-d272-4bdf-8fd7-124fee88a19c") + (at 145 61.75) (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") (tags "fiducial") - (property "Reference" "FID6" + (property "Reference" "FID4" (at 0 -1.95 0) (layer "B.SilkS") (hide yes) - (uuid "9e42bc48-fb7f-477a-b58f-4816a03a72fc") + (uuid "1329f56d-5590-46d9-bb36-0f11655b3d68") (effects (font (size 1 1) @@ -14354,7 +13492,7 @@ (at 0 1.95 0) (layer "B.Fab") (hide yes) - (uuid "42c049a0-d8dc-4de5-a81d-95eb9cfd5c67") + (uuid "622e1404-8efa-4ca4-b735-1488041eee6e") (effects (font (size 1 1) @@ -14367,7 +13505,7 @@ (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "1abdb028-5894-4fc7-a6e3-50f4e64a1f78") + (uuid "8c44d089-86d6-45cb-81eb-0eb33f9a9f05") (effects (font (size 1.27 1.27) @@ -14378,7 +13516,7 @@ (at 0 0 0) (layer "F.Fab") (hide yes) - (uuid "c1d32280-9ca1-4eb4-b66c-7d55255b1583") + (uuid "3271d475-04e0-4560-8cd5-cdafb0a0e862") (effects (font (size 1.27 1.27) @@ -14393,21 +13531,21 @@ (layers "B.Cu" "B.Mask") (solder_mask_margin 0.5) (clearance 0.6) - (uuid "0637a6ba-6179-4d19-9011-92fa770ce038") + (uuid "686ec435-e4c2-476a-a3ac-2b0f3966d08e") ) (embedded_fonts no) ) - (footprint "Package_TO_SOT_SMD:SOT-323_SC-70" + (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "B.Cu") - (uuid "2f51bf7b-f174-4729-a76b-548ad5a8b8cd") - (at 125.3113 91.6275 -90) - (descr "SOT, 3 Pin (https://home.jeita.or.jp/tsc/std-pdf/ED-7500A.pdf#page=148)") - (tags "SOT TO_SOT_SMD SC-70 SOT-323") - (property "Reference" "D_INV_ISO1" - (at 0 1.8 90) + (uuid "1a9ba0b3-7962-454b-a452-bbae057a5f76") + (at 125.75 95.77 -90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_VIN_2" + (at 0 1.16 270) (layer "B.SilkS") (hide yes) - (uuid "f75a766e-786b-4322-98b6-a614dea7d9e6") + (uuid "3f4924b1-fa87-46de-8511-8d14abd9ffe4") (effects (font (size 1 1) @@ -14416,10 +13554,10 @@ (justify mirror) ) ) - (property "Value" "BAT54W-7-F" - (at 0 -1.8 90) + (property "Value" "100nF" + (at 0 -1.16 270) (layer "B.Fab") - (uuid "6eb00ac7-e6ed-4b2b-ad99-bb11b1b86550") + (uuid "5fddc59e-0e12-4b3d-8324-a8fe05ad54b4") (effects (font (size 1 1) @@ -14428,11 +13566,11 @@ (justify mirror) ) ) - (property "Datasheet" "https://www.diodes.com/assets/Datasheets/ds30065.pdf" - (at 0 0 90) + (property "Datasheet" "" + (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "c252513c-a0c7-4174-885b-2a1d18620eaf") + (uuid "f05d216e-7025-431c-82c5-a9678d4b3f46") (effects (font (size 1.27 1.27) @@ -14440,11 +13578,11 @@ (justify mirror) ) ) - (property "Description" "Schottky barrier diode, SOT-323. Pin 1 anode, pin 2 no-connect, pin 3 cathode." - (at 0 0 90) + (property "Description" "Unpolarized capacitor" + (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "24460612-8a75-40cf-93e8-f8fa2de3a99a") + (uuid "85bef30a-7603-4eff-a620-28c31d8c4545") (effects (font (size 1.27 1.27) @@ -14452,25 +13590,12 @@ (justify mirror) ) ) - (property "KiLib_Generator" "package/gullwing" - (at 0 0 90) - (layer "B.SilkS") - (hide yes) - (uuid "ead7da4f-8123-49e1-a32f-703c68e6a720") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "MF" "Diodes Incorporated" + (property "MF" "Samsung Electro-Mechanics" (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "310197b3-3264-482d-ba2a-208c3325813a") + (uuid "e0c9722d-1c27-4b1e-9dc7-ab9465159d2c") (effects (font (size 1 1) @@ -14479,12 +13604,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "BAT54W-7-F" + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "32500094-20c2-40e9-9da4-34911397aade") + (uuid "329de3dc-4ca1-4724-a045-08e8a90e9a62") (effects (font (size 1 1) @@ -14493,12 +13618,12 @@ (justify mirror) ) ) - (property "LCSC" "C134417" + (property "LCSC" "C1525" (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "84c0b37d-cb7a-45e9-821f-f3e9c8ae0bec") + (uuid "7addb406-e375-47a7-8a4e-2e6906c11d7b") (effects (font (size 1 1) @@ -14507,23 +13632,11 @@ (justify mirror) ) ) - (property "Stackup Path" "D_INV_ISO1" - (at 2 0 0) - (layer "B.SilkS") - (hide yes) - (uuid "0a7cb3dd-992d-43ef-acae-d8a5972961c2") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:40" - (at 2 0 0) + (property "Stackup Path" "C_VIN_2" + (at 2 0 180) (layer "B.SilkS") (hide yes) - (uuid "94d9f201-91c5-4cf9-b637-12b293db0d08") + (uuid "5c5bd414-4686-4652-9b01-28f7213a7ae1") (effects (font (size 1.27 1.27) @@ -14531,293 +13644,102 @@ ) ) ) - (property ki_fp_filters "SOT?323*") - (path "/7e9eba98-50a9-51e9-815e-35818fa1dec8") - (units - (unit - (name "A") - (pins "3" "2" "1") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.735 1.135) - (end 0.735 1.135) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "41e30774-a37b-46c7-9a53-37bc39ab3c9a") - ) - (fp_line - (start 0.735 1.135) - (end 0.735 0.485) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "ff1c4ea3-869b-4166-a6d2-1ad344c1ed79") - ) - (fp_line - (start -0.735 -0.165) - (end -0.735 0.165) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "d4f994aa-8965-4fa4-bc94-07758b8872cb") - ) - (fp_line - (start 0.735 -0.485) - (end 0.735 -1.135) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "754cf141-0062-4b76-a295-dc7a4b58388c") - ) - (fp_line - (start 0.735 -1.135) - (end -0.735 -1.135) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "3a878d5d-f1f4-49fc-b68a-1927b2d54994") - ) - (fp_poly - (pts - (xy -1.18 0.16) (xy -1.04 -0.03) (xy -1.32 -0.03) - ) - (stroke - (width 0.12) - (type solid) - ) - (fill yes) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:41" + (at 2 0 180) (layer "B.SilkS") - (uuid "d1c55937-a72c-4b0a-8c44-1baac83e158d") - ) - (fp_line - (start -0.73 1.1) - (end 0.73 1.1) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "66947b09-5b92-403c-9750-ff79700c2e13") - ) - (fp_line - (start 0.73 1.1) - (end 0.73 0.33) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "90090779-1f0e-45e2-a65f-5bb61462a445") - ) - (fp_line - (start -1.45 0.98) - (end -0.73 0.98) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "f700683c-d9a1-4f6c-9d3b-80130542ae82") - ) - (fp_line - (start -0.73 0.98) - (end -0.73 1.1) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "8fa40065-b7a5-4c45-a1b0-02f35d0a0d55") - ) - (fp_line - (start 0.73 0.33) - (end 1.45 0.33) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "d0f1560b-0249-47e8-96ae-168b5bdfbcb1") - ) - (fp_line - (start 1.45 0.33) - (end 1.45 -0.33) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "b544cb26-95d2-43d5-a7bd-a8ca4caedb43") - ) - (fp_line - (start -1.45 0.32) - (end -1.45 0.98) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "6857cc36-80bb-4dd6-b7a9-8d3d32ebda1a") - ) - (fp_line - (start -0.73 0.32) - (end -1.45 0.32) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "2864fbab-90ae-4f01-a469-efc3e9541a2c") - ) - (fp_line - (start -1.45 -0.32) - (end -0.73 -0.32) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "e9befce1-eabc-415e-8929-0d97d17c5a57") - ) - (fp_line - (start -0.73 -0.32) - (end -0.73 0.32) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "0736e30d-d71c-431a-8c66-2a2396dd9760") - ) - (fp_line - (start 0.73 -0.33) - (end 0.73 -1.1) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "dbfb4596-a8ab-4ff1-9021-f60546ab2204") - ) - (fp_line - (start 1.45 -0.33) - (end 0.73 -0.33) - (stroke - (width 0.05) - (type solid) + (hide yes) + (uuid "9833576d-3be8-43a7-9af4-8b2b86fac03f") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) ) - (layer "B.CrtYd") - (uuid "7b82bdb0-800e-4500-b4be-c269d0f6667a") ) - (fp_line - (start -1.45 -0.98) - (end -1.45 -0.32) - (stroke - (width 0.05) - (type solid) + (property ki_fp_filters "C_*") + (path "/767a3c48-9a20-55ce-920a-cf805399b457") + (units + (unit + (name "A") + (pins "1" "2") ) - (layer "B.CrtYd") - (uuid "7b344e6e-1b5a-4ea4-af93-57b109ae1e2a") ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.73 -0.98) - (end -1.45 -0.98) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke - (width 0.05) + (width 0.12) (type solid) ) - (layer "B.CrtYd") - (uuid "60e6fb7c-ad52-4c83-84a3-132397317aff") + (layer "B.SilkS") + (uuid "369f1213-037b-40bd-a3de-703e6bc3505d") ) (fp_line - (start -0.73 -1.1) - (end -0.73 -0.98) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke - (width 0.05) + (width 0.12) (type solid) ) - (layer "B.CrtYd") - (uuid "0a1a35a9-1d50-4339-8f13-d8e3ce6c1330") + (layer "B.SilkS") + (uuid "033aac32-1f1a-4343-9486-6e046ecaa56a") ) - (fp_line - (start 0.73 -1.1) - (end -0.73 -1.1) + (fp_rect + (start -0.91 0.46) + (end 0.91 -0.46) (stroke (width 0.05) (type solid) ) + (fill no) (layer "B.CrtYd") - (uuid "7160f43c-df45-40f0-82e4-089591a4897d") + (uuid "05b89e4d-c3ea-4af0-9486-2409802ecb80") ) - (fp_poly - (pts - (xy -0.3125 1) (xy 0.625 1) (xy 0.625 -1) (xy -0.625 -1) (xy -0.625 0.6875) - ) + (fp_rect + (start -0.5 0.25) + (end 0.5 -0.25) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "441e4f18-3754-438a-904a-caf3ee80caef") + (uuid "d39b05d0-41a9-4e61-87ed-388c7c6041fa") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 270) (layer "B.Fab") - (uuid "ba7a8f50-8f0b-46d4-b3cb-10efe111bba9") + (uuid "5cd8b027-3c74-4b8c-a1f5-c359ba9aae2c") (effects (font - (size 0.5 0.5) - (thickness 0.08) + (size 0.25 0.25) + (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.8875 0.65 270) - (size 0.925 0.45) + (at -0.48 0 270) + (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Control/PWR_BTN_INV_BASE") - (pinfunction "A_1") + (net "VBUS") (pintype "passive") - (uuid "98aa24ba-ee3e-4265-bbab-b048e36a5ba3") + (uuid "6bf76f7e-018c-49c5-ad23-be362d088e4e") ) (pad "2" smd roundrect - (at -0.8875 -0.65 270) - (size 0.925 0.45) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (pinfunction "NC_2") - (pintype "no_connect") - (uuid "a58c93cc-9a3c-45f6-b4e1-2c483202254f") - ) - (pad "3" smd roundrect - (at 0.8875 0 270) - (size 0.925 0.45) + (at 0.48 0 270) + (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/PWR_BTN_SENSE") - (pinfunction "K_3") + (net "GND") (pintype "passive") - (uuid "c1d27084-5e91-4861-8d41-4c9b79cd5220") + (uuid "281631d6-449a-4a07-a14f-bc0bbeff768d") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-323_SC-70.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -14829,17 +13751,17 @@ ) ) ) - (footprint "Diode_SMD:D_SOD-123" + (footprint "Capacitor_SMD:C_0805_2012Metric" (layer "B.Cu") - (uuid "310284b8-eefd-46a2-b1b0-fab8b4191d02") - (at 128.485 78.69 180) - (descr "SOD-123") - (tags "SOD-123") - (property "Reference" "D_OR1" - (at 0 2 0) + (uuid "1d3d471d-1b40-4759-b494-3759590e2ac6") + (at 122.8 95.25 180) + (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (tags "capacitor") + (property "Reference" "C_VIN_1" + (at 0 1.68 180) (layer "B.SilkS") (hide yes) - (uuid "fb9e5328-9b9e-4137-be48-8c9a72ff790c") + (uuid "e7fb09c6-617b-46ac-bff5-d7e60be92855") (effects (font (size 1 1) @@ -14848,10 +13770,10 @@ (justify mirror) ) ) - (property "Value" "1N4148W" - (at 0 -2.1 0) + (property "Value" "10µF" + (at 0 -1.68 180) (layer "B.Fab") - (uuid "8c6fe586-2d56-44ee-9cda-4c10b9ccc70a") + (uuid "604b4445-52ae-4b00-97cb-66a9d3eaf529") (effects (font (size 1 1) @@ -14861,67 +13783,35 @@ ) ) (property "Datasheet" "" - (at 0 0 0) - (unlocked yes) - (layer "B.Fab") - (hide yes) - (uuid "ef3391eb-e4b3-408f-ba86-21bdf077feab") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Description" "Diode, small symbol" - (at 0 0 0) - (unlocked yes) - (layer "B.Fab") - (hide yes) - (uuid "9bbda150-c461-410d-843b-d8a2b073b422") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Sim.Device" "D" (at 0 0 180) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "b042ca15-5177-4ac8-9618-1fd309f7b0b8") + (uuid "2938ee7f-65f7-44f0-af73-4acf38bff7c8") (effects (font - (size 1 1) - (thickness 0.15) + (size 1.27 1.27) ) (justify mirror) ) ) - (property "Sim.Pins" "1=K 2=A" + (property "Description" "Unpolarized capacitor" (at 0 0 180) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "79828b6b-bab2-42cf-939b-631e0054dd20") + (uuid "2145783a-21bf-4035-bc26-9186a7d7a3ed") (effects (font - (size 1 1) - (thickness 0.15) + (size 1.27 1.27) ) (justify mirror) ) ) - (property "MF" "ST(Semtech)" + (property "MF" "Samsung Electro-Mechanics" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "d4005938-13e0-4d58-a4a6-527004470e2b") + (uuid "19913c2d-829e-4aad-ad12-a8c0fd4d9b84") (effects (font (size 1 1) @@ -14930,12 +13820,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "1N4148W" + (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "3e9b37a8-006e-4751-bf7d-8f96891adba3") + (uuid "157ab6f8-a236-4733-aef3-73534a6b42c2") (effects (font (size 1 1) @@ -14944,12 +13834,12 @@ (justify mirror) ) ) - (property "LCSC" "C81598" + (property "LCSC" "C15850" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "52666246-9472-425b-8899-6520ec338bf2") + (uuid "8ed366da-fc44-4b02-b9e0-21d8f90a89da") (effects (font (size 1 1) @@ -14958,11 +13848,11 @@ (justify mirror) ) ) - (property "Stackup Path" "D_OR1" - (at 2 0 270) + (property "Stackup Path" "C_VIN_1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "cc926398-656d-464c-88f0-ac6d6d7425ca") + (uuid "2c974235-1d97-4cbb-85e1-fff6f355c1df") (effects (font (size 1.27 1.27) @@ -14970,11 +13860,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:41" - (at 2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:40" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "6c26a98b-c534-4376-8a0e-361649d36e90") + (uuid "3442f931-428e-48a6-b4a9-020bc1f8d17d") (effects (font (size 1.27 1.27) @@ -14982,8 +13872,8 @@ ) ) ) - (property ki_fp_filters "TO-???* *_Diode_* *SingleDiode* D_*") - (path "/b496a53a-138c-51cf-af92-61108d5cc51d") + (property ki_fp_filters "C_*") + (path "/86103b52-000a-5cd5-a338-7553101cd180") (units (unit (name "A") @@ -14993,219 +13883,361 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -2.36 1) - (end 1.65 1) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "9fb2ea1e-a102-4834-b5c0-c97c80cc4db6") - ) - (fp_line - (start -2.36 1) - (end -2.36 -1) + (start -0.261252 0.735) + (end 0.261252 0.735) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "70715ee8-c2b6-45d1-861b-7985db1c9356") + (uuid "c7890148-5f3d-44fd-9a5a-e5f2bd1055a2") ) (fp_line - (start -2.36 -1) - (end 1.65 -1) + (start -0.261252 -0.735) + (end 0.261252 -0.735) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "5cd7e60d-994a-43fc-9211-e79bee3ca6c1") + (uuid "6ec55279-e7e9-46c4-adde-1f4123425431") ) - (fp_line - (start 2.35 1.15) - (end 2.35 -1.15) + (fp_rect + (start -1.7 0.98) + (end 1.7 -0.98) (stroke (width 0.05) (type solid) ) + (fill no) (layer "B.CrtYd") - (uuid "e99698fa-afdc-4f63-8037-a9f5fc04a755") + (uuid "32ab2798-8262-4c0b-b2c6-1de3cfe88163") ) - (fp_line - (start 2.35 -1.15) - (end -2.35 -1.15) + (fp_rect + (start -1 0.625) + (end 1 -0.625) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (layer "B.CrtYd") - (uuid "95a2c0d5-7f08-40f4-97c0-43f0e627abf1") + (fill no) + (layer "B.Fab") + (uuid "4849e0f2-fba7-4541-ab64-ca8f7b3c14cc") ) - (fp_line - (start -2.35 1.15) - (end 2.35 1.15) - (stroke - (width 0.05) - (type solid) + (fp_text user "${REFERENCE}" + (at 0 0 180) + (layer "B.Fab") + (uuid "b0240c8b-4db2-4ade-b6cd-923dcc45df38") + (effects + (font + (size 0.5 0.5) + (thickness 0.08) + ) + (justify mirror) ) - (layer "B.CrtYd") - (uuid "be50f902-7d9b-4f1a-9d18-a2bc98ea1bc3") ) - (fp_line - (start -2.35 1.15) - (end -2.35 -1.15) - (stroke - (width 0.05) - (type solid) + (pad "1" smd roundrect + (at -0.95 0 180) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "VBUS") + (pintype "passive") + (uuid "fcf92e42-45bd-449b-805f-21244811038d") + ) + (pad "2" smd roundrect + (at 0.95 0 180) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "22c7ee91-608a-4648-b0e5-6ed42fb011e8") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) ) - (layer "B.CrtYd") - (uuid "d36d6a1d-90ec-4503-bbf2-863604fb84f5") ) - (fp_line - (start 1.4 0.9) - (end 1.4 -0.9) - (stroke - (width 0.1) - (type solid) + ) + (footprint "Fiducial:Fiducial_1mm_Mask2mm" + (layer "B.Cu") + (uuid "1eed4b54-beb5-4c1a-8345-3ed6feafa395") + (at 144.5 128.25) + (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") + (tags "fiducial") + (property "Reference" "FID6" + (at 0 -1.95 0) + (layer "B.SilkS") + (hide yes) + (uuid "9e42bc48-fb7f-477a-b58f-4816a03a72fc") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) ) + ) + (property "Value" "Fiducial_1mm_Mask2mm" + (at 0 1.95 0) (layer "B.Fab") - (uuid "d7d4a373-7220-4869-810d-7524b37fdf81") + (hide yes) + (uuid "42c049a0-d8dc-4de5-a81d-95eb9cfd5c67") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (fp_line - (start 1.4 -0.9) - (end -1.4 -0.9) - (stroke - (width 0.1) - (type solid) + (property "Datasheet" "" + (at 0 0 0) + (layer "F.Fab") + (hide yes) + (uuid "1abdb028-5894-4fc7-a6e3-50f4e64a1f78") + (effects + (font + (size 1.27 1.27) + ) ) - (layer "B.Fab") - (uuid "a64841e6-23b9-4f7d-b8f6-0b36095cd1b7") ) - (fp_line - (start 0.25 0.4) - (end 0.25 -0.4) - (stroke - (width 0.1) - (type solid) + (property "Description" "" + (at 0 0 0) + (layer "F.Fab") + (hide yes) + (uuid "c1d32280-9ca1-4eb4-b66c-7d55255b1583") + (effects + (font + (size 1.27 1.27) + ) ) - (layer "B.Fab") - (uuid "7d95a937-7a89-45ab-bbef-db2f5c184a46") ) - (fp_line - (start 0.25 0) - (end 0.75 0) - (stroke - (width 0.1) - (type solid) + (attr smd board_only exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (pad "" smd circle + (at 0 0) + (size 1 1) + (layers "B.Cu" "B.Mask") + (solder_mask_margin 0.5) + (clearance 0.6) + (uuid "0637a6ba-6179-4d19-9011-92fa770ce038") + ) + (embedded_fonts no) + ) + (footprint "Capacitor_SMD:C_0805_2012Metric" + (layer "B.Cu") + (uuid "2513389e-e2b0-45c2-938c-0301fd0d713f") + (at 138.025 95.75 -90) + (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (tags "capacitor") + (property "Reference" "C_BUCK_OUT1" + (at 0 1.68 270) + (layer "B.SilkS") + (hide yes) + (uuid "4051d71d-2b5a-40ca-b439-7c470ea75381") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) ) - (layer "B.Fab") - (uuid "e307e70b-931f-4481-8a66-36c1e78bb149") ) - (fp_line - (start 0.25 -0.4) - (end -0.35 0) - (stroke - (width 0.1) - (type solid) + (property "Value" "22µF" + (at 0 -1.68 270) + (layer "B.Fab") + (uuid "82e7b1a7-567e-49a7-9271-1f94929512d6") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) ) + ) + (property "Datasheet" "" + (at 0 0 270) (layer "B.Fab") - (uuid "4ebe848c-abbb-42b3-bbd6-2e972442f518") + (hide yes) + (uuid "21cfd4d9-ff48-4580-be44-b0d939b456b3") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) ) - (fp_line - (start -0.35 0) - (end 0.25 0.4) - (stroke - (width 0.1) - (type solid) + (property "Description" "Unpolarized capacitor" + (at 0 0 270) + (layer "B.Fab") + (hide yes) + (uuid "c4f828b3-dd18-4e7a-9d02-a171edb53cae") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) ) + ) + (property "MF" "Samsung Electro-Mechanics" + (at 0 0 270) + (unlocked yes) (layer "B.Fab") - (uuid "06564f1e-c1ce-4550-8317-56ab4d9204ea") + (hide yes) + (uuid "c2feac37-1118-4816-b1af-7caa66b7b5a9") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (fp_line - (start -0.35 0) - (end -0.35 0.55) - (stroke - (width 0.1) - (type solid) + (property "Manufacturer_Part_Number" "CL21A226MAQNNNE" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "1de9d2a1-fcf2-45f1-a6ed-92b607e1b429") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) ) + ) + (property "LCSC" "C45783" + (at 0 0 270) + (unlocked yes) (layer "B.Fab") - (uuid "c2ac1c7c-2716-45a4-855f-35a1093532d4") + (hide yes) + (uuid "2facc8dc-af31-48b2-a602-60af3575e762") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Stackup Path" "C_BUCK_OUT1" + (at 2 0 180) + (layer "B.SilkS") + (hide yes) + (uuid "6801ec0c-3ba1-48e4-b492-5ac547210be9") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:26" + (at 2 0 180) + (layer "B.SilkS") + (hide yes) + (uuid "7076765b-2e1d-4cfb-8ea5-3bce1ac1b429") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "C_*") + (path "/9c031725-c12c-5f56-9f8e-dce0669b7cb5") + (units + (unit + (name "A") + (pins "1" "2") + ) ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.35 0) - (end -0.35 -0.55) + (start -0.261252 0.735) + (end 0.261252 0.735) (stroke - (width 0.1) + (width 0.12) (type solid) ) - (layer "B.Fab") - (uuid "b3c23924-9d89-40f7-8acc-3c55fb6ee955") + (layer "B.SilkS") + (uuid "3a3c1d5a-a0ed-42f7-b8be-fb078e8c5f59") ) (fp_line - (start -0.75 0) - (end -0.35 0) + (start -0.261252 -0.735) + (end 0.261252 -0.735) (stroke - (width 0.1) + (width 0.12) (type solid) ) - (layer "B.Fab") - (uuid "c6765211-15b4-487b-a877-fe6176679f9b") + (layer "B.SilkS") + (uuid "b7145f12-9f03-41c0-aee8-95ebde1519d8") ) - (fp_line - (start -1.4 0.9) - (end 1.4 0.9) + (fp_rect + (start -1.7 0.98) + (end 1.7 -0.98) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "118c046f-0db9-4f3d-b0f4-b7c462f83e96") + (fill no) + (layer "B.CrtYd") + (uuid "ab26275f-3101-43b8-8a0b-32225b46f421") ) - (fp_line - (start -1.4 -0.9) - (end -1.4 0.9) + (fp_rect + (start -1 0.625) + (end 1 -0.625) (stroke (width 0.1) (type solid) ) + (fill no) (layer "B.Fab") - (uuid "4271e39d-1911-4042-b54e-4cb56b3813f9") + (uuid "515e97c8-abcf-4727-be67-59b12f45c820") ) (fp_text user "${REFERENCE}" - (at 0 2 0) + (at 0 0 270) (layer "B.Fab") - (uuid "4ac0511b-c0d7-4a0d-8045-d5d2329c98ed") + (uuid "a7a437c7-9d7d-49ac-817e-c8d224bf4b1a") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.5 0.5) + (thickness 0.08) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -1.65 0 180) - (size 0.9 1.2) + (at -0.95 0 270) + (size 1 1.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Control/PWR_LATCH_G") - (pinfunction "K_1") + (net "3V3") (pintype "passive") - (uuid "d0cccb5f-47c5-41cd-addc-1e460ba7b371") + (uuid "d0ada20f-1079-46de-840a-2063dcbb67f2") ) (pad "2" smd roundrect - (at 1.65 0 180) - (size 0.9 1.2) + (at 0.95 0 270) + (size 1 1.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Control/PWR_BTN_TRIGGER") - (pinfunction "A_2") + (net "GND") (pintype "passive") - (uuid "93ad1cbc-eb39-44d2-9c61-801cf79662d8") + (uuid "4fa9d337-00fb-4430-9c3b-d655757bb4aa") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Diode_SMD.3dshapes/D_SOD-123.step" + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" (offset (xyz 0 0 0) ) @@ -15217,17 +14249,17 @@ ) ) ) - (footprint "Resistor_SMD:R_0402_1005Metric" + (footprint "Package_TO_SOT_SMD:SOT-323_SC-70" (layer "B.Cu") - (uuid "3c8a3d7a-b3ba-4c63-a9a6-631c89fc3356") - (at 140.935 80.24) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_PWR_EN_PD1" - (at 1.129326 7.902578 0) + (uuid "2f51bf7b-f174-4729-a76b-548ad5a8b8cd") + (at 125.3113 91.6275 -90) + (descr "SOT, 3 Pin (https://home.jeita.or.jp/tsc/std-pdf/ED-7500A.pdf#page=148)") + (tags "SOT TO_SOT_SMD SC-70 SOT-323") + (property "Reference" "D_INV_ISO1" + (at 0 1.8 90) (layer "B.SilkS") (hide yes) - (uuid "3a91482e-deba-40f8-94f8-9aaed47577d6") + (uuid "f75a766e-786b-4322-98b6-a614dea7d9e6") (effects (font (size 1 1) @@ -15236,10 +14268,10 @@ (justify mirror) ) ) - (property "Value" "100kΩ" - (at 0 -1.17 0) + (property "Value" "BAT54W-7-F" + (at 0 -1.8 90) (layer "B.Fab") - (uuid "190badc0-99f5-49cd-a801-6ac92a88ce63") + (uuid "6eb00ac7-e6ed-4b2b-ad99-bb11b1b86550") (effects (font (size 1 1) @@ -15248,11 +14280,11 @@ (justify mirror) ) ) - (property "Datasheet" "" - (at 0 0 0) + (property "Datasheet" "https://www.diodes.com/assets/Datasheets/ds30065.pdf" + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "7b4601c3-c924-4127-b3be-b9bb1649965d") + (uuid "c252513c-a0c7-4174-885b-2a1d18620eaf") (effects (font (size 1.27 1.27) @@ -15260,11 +14292,11 @@ (justify mirror) ) ) - (property "Description" "Resistor" - (at 0 0 0) + (property "Description" "Schottky barrier diode, SOT-323. Pin 1 anode, pin 2 no-connect, pin 3 cathode." + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "21fd61b7-ba14-4557-8eb9-87911032e0db") + (uuid "24460612-8a75-40cf-93e8-f8fa2de3a99a") (effects (font (size 1.27 1.27) @@ -15272,11 +14304,11 @@ (justify mirror) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 0) + (property "KiLib_Generator" "package/gullwing" + (at 0 0 90) (layer "B.SilkS") (hide yes) - (uuid "e56b6423-b735-4b62-8de2-66bbafe97e02") + (uuid "ead7da4f-8123-49e1-a32f-703c68e6a720") (effects (font (size 1 1) @@ -15285,12 +14317,12 @@ (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 180) + (property "MF" "Diodes Incorporated" + (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "4c1b962c-a5a4-4e5d-a4ab-71b5f04db3f0") + (uuid "310197b3-3264-482d-ba2a-208c3325813a") (effects (font (size 1 1) @@ -15299,12 +14331,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF1003TCE" - (at 0 0 180) + (property "Manufacturer_Part_Number" "BAT54W-7-F" + (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "0bbe58cd-aaee-48b1-a033-14b668473729") + (uuid "32500094-20c2-40e9-9da4-34911397aade") (effects (font (size 1 1) @@ -15313,12 +14345,12 @@ (justify mirror) ) ) - (property "LCSC" "C25741" - (at 0 0 180) + (property "LCSC" "C134417" + (at 0 0 270) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "6358ea15-bb81-4fe5-8420-e682c1f852db") + (uuid "84c0b37d-cb7a-45e9-821f-f3e9c8ae0bec") (effects (font (size 1 1) @@ -15327,11 +14359,11 @@ (justify mirror) ) ) - (property "Stackup Path" "R_PWR_EN_PD1" - (at -2 0 270) + (property "Stackup Path" "D_INV_ISO1" + (at 2 0 0) (layer "B.SilkS") (hide yes) - (uuid "b70a2881-d213-474f-a221-d15e5fed45c0") + (uuid "0a7cb3dd-992d-43ef-acae-d8a5972961c2") (effects (font (size 1.27 1.27) @@ -15339,11 +14371,11 @@ ) ) ) - (property "Stackup Source" "@stackup/passives.kdl:126" - (at -2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:42" + (at 2 0 0) (layer "B.SilkS") (hide yes) - (uuid "a1525269-e758-4655-8b66-373e77e6ac77") + (uuid "94d9f201-91c5-4cf9-b637-12b293db0d08") (effects (font (size 1.27 1.27) @@ -15351,90 +14383,293 @@ ) ) ) - (property ki_fp_filters "R_*") - (path "/e49fe592-c225-51f5-816f-a451f2a1b535") + (property ki_fp_filters "SOT?323*") + (path "/7e9eba98-50a9-51e9-815e-35818fa1dec8") (units (unit (name "A") - (pins "1" "2") + (pins "3" "2" "1") ) ) (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.735 1.135) + (end 0.735 1.135) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "2a3cdd9b-d0ac-484f-b280-b11bfbf2c4ee") + (uuid "41e30774-a37b-46c7-9a53-37bc39ab3c9a") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start 0.735 1.135) + (end 0.735 0.485) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "f8c2000c-4367-4d59-85e3-dfdcf0d0aad1") + (uuid "ff1c4ea3-869b-4166-a6d2-1ad344c1ed79") ) - (fp_rect - (start -0.93 0.47) - (end 0.93 -0.47) + (fp_line + (start -0.735 -0.165) + (end -0.735 0.165) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "d4f994aa-8965-4fa4-bc94-07758b8872cb") + ) + (fp_line + (start 0.735 -0.485) + (end 0.735 -1.135) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "754cf141-0062-4b76-a295-dc7a4b58388c") + ) + (fp_line + (start 0.735 -1.135) + (end -0.735 -1.135) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "3a878d5d-f1f4-49fc-b68a-1927b2d54994") + ) + (fp_poly + (pts + (xy -1.18 0.16) (xy -1.04 -0.03) (xy -1.32 -0.03) + ) + (stroke + (width 0.12) + (type solid) + ) + (fill yes) + (layer "B.SilkS") + (uuid "d1c55937-a72c-4b0a-8c44-1baac83e158d") + ) + (fp_line + (start -0.73 1.1) + (end 0.73 1.1) (stroke (width 0.05) (type solid) ) - (fill no) (layer "B.CrtYd") - (uuid "066d8fe9-5a65-45f9-ae86-b99d5ddbf8ad") + (uuid "66947b09-5b92-403c-9750-ff79700c2e13") ) - (fp_rect - (start -0.525 0.27) - (end 0.525 -0.27) + (fp_line + (start 0.73 1.1) + (end 0.73 0.33) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "90090779-1f0e-45e2-a65f-5bb61462a445") + ) + (fp_line + (start -1.45 0.98) + (end -0.73 0.98) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "f700683c-d9a1-4f6c-9d3b-80130542ae82") + ) + (fp_line + (start -0.73 0.98) + (end -0.73 1.1) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "8fa40065-b7a5-4c45-a1b0-02f35d0a0d55") + ) + (fp_line + (start 0.73 0.33) + (end 1.45 0.33) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "d0f1560b-0249-47e8-96ae-168b5bdfbcb1") + ) + (fp_line + (start 1.45 0.33) + (end 1.45 -0.33) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "b544cb26-95d2-43d5-a7bd-a8ca4caedb43") + ) + (fp_line + (start -1.45 0.32) + (end -1.45 0.98) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "6857cc36-80bb-4dd6-b7a9-8d3d32ebda1a") + ) + (fp_line + (start -0.73 0.32) + (end -1.45 0.32) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "2864fbab-90ae-4f01-a469-efc3e9541a2c") + ) + (fp_line + (start -1.45 -0.32) + (end -0.73 -0.32) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "e9befce1-eabc-415e-8929-0d97d17c5a57") + ) + (fp_line + (start -0.73 -0.32) + (end -0.73 0.32) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "0736e30d-d71c-431a-8c66-2a2396dd9760") + ) + (fp_line + (start 0.73 -0.33) + (end 0.73 -1.1) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "dbfb4596-a8ab-4ff1-9021-f60546ab2204") + ) + (fp_line + (start 1.45 -0.33) + (end 0.73 -0.33) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "7b82bdb0-800e-4500-b4be-c269d0f6667a") + ) + (fp_line + (start -1.45 -0.98) + (end -1.45 -0.32) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "7b344e6e-1b5a-4ea4-af93-57b109ae1e2a") + ) + (fp_line + (start -0.73 -0.98) + (end -1.45 -0.98) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "60e6fb7c-ad52-4c83-84a3-132397317aff") + ) + (fp_line + (start -0.73 -1.1) + (end -0.73 -0.98) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "0a1a35a9-1d50-4339-8f13-d8e3ce6c1330") + ) + (fp_line + (start 0.73 -1.1) + (end -0.73 -1.1) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "7160f43c-df45-40f0-82e4-089591a4897d") + ) + (fp_poly + (pts + (xy -0.3125 1) (xy 0.625 1) (xy 0.625 -1) (xy -0.625 -1) (xy -0.625 0.6875) + ) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "7c44618f-b498-4288-be0f-9f8227c2448c") + (uuid "441e4f18-3754-438a-904a-caf3ee80caef") ) (fp_text user "${REFERENCE}" (at 0 0 0) (layer "B.Fab") - (uuid "f22346ee-4b90-40ec-b714-24ca4ff64433") + (uuid "ba7a8f50-8f0b-46d4-b3cb-10efe111bba9") (effects (font - (size 0.26 0.26) - (thickness 0.04) + (size 0.5 0.5) + (thickness 0.08) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) + (at -0.8875 0.65 270) + (size 0.925 0.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Buck/PWR_EN") + (net "/Power_Control/PWR_BTN_INV_BASE") + (pinfunction "A_1") (pintype "passive") - (uuid "def0862f-a50c-4f4b-a0a5-d81ead21058c") + (uuid "98aa24ba-ee3e-4265-bbab-b048e36a5ba3") ) (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) + (at -0.8875 -0.65 270) + (size 0.925 0.45) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "GND") + (pinfunction "NC_2") + (pintype "no_connect") + (uuid "a58c93cc-9a3c-45f6-b4e1-2c483202254f") + ) + (pad "3" smd roundrect + (at 0.8875 0 270) + (size 0.925 0.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "/MCU_Core/PWR_BTN_SENSE") + (pinfunction "K_3") (pintype "passive") - (uuid "af485da4-8949-4169-ba54-20897de03dd2") + (uuid "c1d27084-5e91-4861-8d41-4c9b79cd5220") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-323_SC-70.step" (offset (xyz 0 0 0) ) @@ -15446,17 +14681,17 @@ ) ) ) - (footprint "Fiducial:Fiducial_1mm_Mask2mm" + (footprint "Diode_SMD:D_SOD-123" (layer "B.Cu") - (uuid "3f4e415c-2019-4bf1-a307-2d92c8ec5904") - (at 122.75 128.25) - (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") - (tags "fiducial") - (property "Reference" "FID5" - (at 0 -1.95 0) + (uuid "310284b8-eefd-46a2-b1b0-fab8b4191d02") + (at 128.485 78.69 180) + (descr "SOD-123") + (tags "SOD-123") + (property "Reference" "D_OR1" + (at 0 2 0) (layer "B.SilkS") (hide yes) - (uuid "21b106c5-de31-4725-86b3-da18830ce282") + (uuid "fb9e5328-9b9e-4137-be48-8c9a72ff790c") (effects (font (size 1 1) @@ -15465,11 +14700,10 @@ (justify mirror) ) ) - (property "Value" "Fiducial_1mm_Mask2mm" - (at 0 1.95 0) + (property "Value" "1N4148W" + (at 0 -2.1 0) (layer "B.Fab") - (hide yes) - (uuid "501f247d-0e52-4f62-9920-bcb96cd8421e") + (uuid "8c6fe586-2d56-44ee-9cda-4c10b9ccc70a") (effects (font (size 1 1) @@ -15480,409 +14714,350 @@ ) (property "Datasheet" "" (at 0 0 0) - (layer "F.Fab") + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "2112655d-6cb2-496f-aac0-d8e1a61d6454") + (uuid "ef3391eb-e4b3-408f-ba86-21bdf077feab") (effects (font (size 1.27 1.27) + (thickness 0.15) ) + (justify mirror) ) ) - (property "Description" "" + (property "Description" "Diode, small symbol" (at 0 0 0) - (layer "F.Fab") + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "643c9ba5-ebeb-4d56-aa92-063cd66ebb31") + (uuid "9bbda150-c461-410d-843b-d8a2b073b422") (effects (font (size 1.27 1.27) - ) - ) - ) - (attr smd board_only exclude_from_bom) - (duplicate_pad_numbers_are_jumpers no) - (pad "" smd circle - (at 0 0) - (size 1 1) - (layers "B.Cu" "B.Mask") - (solder_mask_margin 0.5) - (clearance 0.6) - (uuid "a813db40-9e4e-468a-a73b-158291e52110") - ) - (embedded_fonts no) - ) - (footprint "SW_Alps_SKRP" - (layer "B.Cu") - (uuid "3f83cf94-f870-45cc-a20b-93ecb451363c") - (at 146.175 105.875) - (descr "Alps SKRP 4.2x3.2x2.5mm tact switch, 4 pads. Land from the Alps SKRP datasheet (PC board land dimensions): 5.2/3.1 x 2.8/1.5 mm. Terminals 1-2 and 3-4 are joined inside, so pad 1 is the top pair and pad 2 the bottom pair. 3D model is the same-size C&K PTS810.") - (tags "SPST Button Switch") - (property "Reference" "SW_BOOT1" - (at 0.005 2.334999 0) - (layer "B.SilkS") - (hide yes) - (uuid "e3cb0a6a-4ca4-47c3-b506-a9a395dc85c0") - (effects - (font - (size 0.8 0.8) - (thickness 0.12) - ) - (justify mirror) - ) - ) - (property "Value" "SKRPABE010" - (at 1.675 -8.15 0) - (layer "B.Fab") - (uuid "05255947-9350-4e85-9825-129599b193b9") - (effects - (font - (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Datasheet" "" + (property "Sim.Device" "D" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "a8e38cc8-5fe6-4fd8-8c13-43a91a35a405") + (uuid "b042ca15-5177-4ac8-9618-1fd309f7b0b8") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "" + (property "Sim.Pins" "1=K 2=A" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "48a9692c-d32e-43f9-b495-cd53e8a958fa") + (uuid "79828b6b-bab2-42cf-939b-631e0054dd20") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "Alps Alpine" - (at -2 0 90) - (layer "B.SilkS") + (property "MF" "ST(Semtech)" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "8277542c-aa73-4ea5-8a67-9fec78eedd1c") + (uuid "d4005938-13e0-4d58-a4a6-527004470e2b") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "SKRPABE010" - (at -2 0 90) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "1N4148W" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "b7d966ce-2490-416d-9b7b-2965ae0e1174") + (uuid "3e9b37a8-006e-4751-bf7d-8f96891adba3") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C115360" - (at -2 0 90) - (layer "B.SilkS") + (property "LCSC" "C81598" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "c8399077-e80e-4225-8a2e-4e8fae984198") + (uuid "52666246-9472-425b-8899-6520ec338bf2") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Path" "SW_BOOT1" - (at -2 0 90) + (property "Stackup Path" "D_OR1" + (at 2 0 270) (layer "B.SilkS") (hide yes) - (uuid "9b03ee93-8e75-4914-a323-6838ff873c49") + (uuid "cc926398-656d-464c-88f0-ac6d6d7425ca") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:72" - (at -2 0 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:43" + (at 2 0 270) (layer "B.SilkS") (hide yes) - (uuid "85d7efba-87c4-4cc8-b850-29127b1ad6ff") + (uuid "6c26a98b-c534-4376-8a0e-361649d36e90") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) - ) - ) - (path "/04731770-7be7-5c5c-9ac0-967af43661c6") - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -2.2 -1.7) - (end 2.2 -1.7) - (stroke - (width 0.12) - (type solid) ) - (layer "B.SilkS") - (uuid "d23d79fb-bdd1-495f-96b6-1180ffcf411e") ) - (fp_line - (start -2.2 -1.58) - (end -2.2 -1.7) - (stroke - (width 0.12) - (type solid) + (property ki_fp_filters "TO-???* *_Diode_* *SingleDiode* D_*") + (path "/b496a53a-138c-51cf-af92-61108d5cc51d") + (units + (unit + (name "A") + (pins "1" "2") ) - (layer "B.SilkS") - (uuid "304aa510-e2ba-4650-a8ff-c27bb9ce4cb4") ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -2.2 0.57) - (end -2.2 -0.57) + (start -2.36 1) + (end 1.65 1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "afc1dd0b-be47-4c65-8c8a-b007f10d9920") + (uuid "9fb2ea1e-a102-4834-b5c0-c97c80cc4db6") ) (fp_line - (start -2.2 1.7) - (end -2.2 1.58) + (start -2.36 1) + (end -2.36 -1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "d11fa051-301a-4ddf-947b-c4ccc65af0df") + (uuid "70715ee8-c2b6-45d1-861b-7985db1c9356") ) (fp_line - (start 2.2 -1.7) - (end 2.2 -1.58) + (start -2.36 -1) + (end 1.65 -1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "98edcc55-4e27-4d6e-b8ed-ef7afbf38b22") + (uuid "5cd7e60d-994a-43fc-9211-e79bee3ca6c1") ) (fp_line - (start 2.2 -0.57) - (end 2.2 0.57) + (start 2.35 1.15) + (end 2.35 -1.15) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "e11414d9-4cdf-4555-921e-a1ccf6e4fe09") + (layer "B.CrtYd") + (uuid "e99698fa-afdc-4f63-8037-a9f5fc04a755") ) (fp_line - (start 2.2 1.58) - (end 2.2 1.7) + (start 2.35 -1.15) + (end -2.35 -1.15) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "5d934c1d-34ed-4f01-9a3b-c6a788f88304") + (layer "B.CrtYd") + (uuid "95a2c0d5-7f08-40f4-97c0-43f0e627abf1") ) (fp_line - (start 2.2 1.7) - (end -2.2 1.7) + (start -2.35 1.15) + (end 2.35 1.15) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "8fdee38a-b400-44a5-a61a-4c4b6619f561") + (layer "B.CrtYd") + (uuid "be50f902-7d9b-4f1a-9d18-a2bc98ea1bc3") ) (fp_line - (start -2.85 -1.85) - (end -2.85 1.85) + (start -2.35 1.15) + (end -2.35 -1.15) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "e616d30f-327b-44e2-b93b-eb7bdff3ab1b") + (uuid "d36d6a1d-90ec-4503-bbf2-863604fb84f5") ) (fp_line - (start -2.85 1.85) - (end 2.85 1.85) + (start 1.4 0.9) + (end 1.4 -0.9) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (layer "B.CrtYd") - (uuid "17fde1c8-cfc5-478d-8e62-8ed644202a24") + (layer "B.Fab") + (uuid "d7d4a373-7220-4869-810d-7524b37fdf81") ) (fp_line - (start 2.85 -1.85) - (end -2.85 -1.85) + (start 1.4 -0.9) + (end -1.4 -0.9) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (layer "B.CrtYd") - (uuid "caf9e977-efc9-44de-ab87-0d371b762113") + (layer "B.Fab") + (uuid "a64841e6-23b9-4f7d-b8f6-0b36095cd1b7") ) (fp_line - (start 2.85 1.85) - (end 2.85 -1.85) + (start 0.25 0.4) + (end 0.25 -0.4) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (layer "B.CrtYd") - (uuid "7890df47-7d7a-4c90-93be-db5fa9f695dc") + (layer "B.Fab") + (uuid "7d95a937-7a89-45ab-bbef-db2f5c184a46") ) (fp_line - (start -2.1 -1.6) - (end 2.1 -1.6) + (start 0.25 0) + (end 0.75 0) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "9b5f2db8-b7e4-47d2-8cc8-109afdb87355") + (uuid "e307e70b-931f-4481-8a66-36c1e78bb149") ) (fp_line - (start -2.1 1.6) - (end -2.1 -1.6) + (start 0.25 -0.4) + (end -0.35 0) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "c016533b-1069-4d90-ad12-4f04f56576c8") + (uuid "4ebe848c-abbb-42b3-bbd6-2e972442f518") ) (fp_line - (start -0.4 1.1) - (end 0.4 1.1) + (start -0.35 0) + (end 0.25 0.4) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "acd6497d-b778-44cc-adcb-86f4e04c4cc1") + (uuid "06564f1e-c1ce-4550-8317-56ab4d9204ea") ) (fp_line - (start 0.4 -1.1) - (end -0.4 -1.1) + (start -0.35 0) + (end -0.35 0.55) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "74fb357d-3ffe-423c-afae-b2359b8c1c53") + (uuid "c2ac1c7c-2716-45a4-855f-35a1093532d4") ) (fp_line - (start 2.1 -1.6) - (end 2.1 1.6) + (start -0.35 0) + (end -0.35 -0.55) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "9fb3fe7c-1026-4b0f-a7e6-7edefc2a00b7") + (uuid "b3c23924-9d89-40f7-8acc-3c55fb6ee955") ) (fp_line - (start 2.1 1.6) - (end -2.1 1.6) + (start -0.75 0) + (end -0.35 0) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "a310bc9e-245f-4f5b-a3c3-5bfbb9593525") + (uuid "c6765211-15b4-487b-a877-fe6176679f9b") ) - (fp_arc - (start -0.4 1.1) - (mid -1.5 0) - (end -0.4 -1.1) + (fp_line + (start -1.4 0.9) + (end 1.4 0.9) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "e40f9b23-7ca2-4a49-9b62-668ec0bb1e86") + (uuid "118c046f-0db9-4f3d-b0f4-b7c462f83e96") ) - (fp_arc - (start 0.4 -1.1) - (mid 1.5 0) - (end 0.4 1.1) + (fp_line + (start -1.4 -0.9) + (end -1.4 0.9) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "a11f0749-f6ae-458b-b84a-40aadd4a7d48") + (uuid "4271e39d-1911-4042-b54e-4cb56b3813f9") ) (fp_text user "${REFERENCE}" - (at 1.675 -5.55 0) + (at 0 2 0) (layer "B.Fab") - (uuid "7afe7d61-532e-4e6b-9522-a726563c1cc1") + (uuid "4ac0511b-c0d7-4a0d-8045-d5d2329c98ed") (effects (font - (size 0.6 0.6) - (thickness 0.09) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (pad "1" smd rect - (at -2.075 1.075) - (size 1.05 0.65) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "958c36fe-269d-4e38-b7cc-28186e3b6589") - ) - (pad "1" smd rect - (at 2.075 1.075) - (size 1.05 0.65) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "cca9a5af-a604-4069-9af6-a0dcafa16afa") - ) - (pad "2" smd rect - (at -2.075 -1.075) - (size 1.05 0.65) + (pad "1" smd roundrect + (at -1.65 0 180) + (size 0.9 1.2) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_BOOT") - (uuid "6d3f76dd-3479-42ab-ba72-1be271e462cc") + (roundrect_rratio 0.25) + (net "/Power_Control/PWR_LATCH_G") + (pinfunction "K_1") + (pintype "passive") + (uuid "d0cccb5f-47c5-41cd-addc-1e460ba7b371") ) - (pad "2" smd rect - (at 2.075 -1.075) - (size 1.05 0.65) + (pad "2" smd roundrect + (at 1.65 0 180) + (size 0.9 1.2) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_BOOT") - (uuid "b06922c9-5384-454f-a2a3-a9c27a2699da") + (roundrect_rratio 0.25) + (net "/Power_Control/PWR_BTN_TRIGGER") + (pinfunction "A_2") + (pintype "passive") + (uuid "93ad1cbc-eb39-44d2-9c61-801cf79662d8") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Button_Switch_SMD.3dshapes/SW_SPST_PTS810.step" + (model "${KICAD10_3DMODEL_DIR}/Diode_SMD.3dshapes/D_SOD-123.step" (offset (xyz 0 0 0) ) @@ -15894,17 +15069,17 @@ ) ) ) - (footprint "C_0402_1005Metric" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "4211ee0a-ab80-46ad-8319-8723fea825d9") - (at 131.5 91.75 180) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_TRIG1" - (at 0 1.16 0) + (uuid "3c8a3d7a-b3ba-4c63-a9a6-631c89fc3356") + (at 140.935 80.24) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_PWR_EN_PD1" + (at 1.129326 7.902578 0) (layer "B.SilkS") (hide yes) - (uuid "bf516266-ec26-4191-a6dc-ab5c960b1b10") + (uuid "3a91482e-deba-40f8-94f8-9aaed47577d6") (effects (font (size 1 1) @@ -15913,10 +15088,10 @@ (justify mirror) ) ) - (property "Value" "100nF" - (at 0 -1.16 0) + (property "Value" "100kΩ" + (at 0 -1.17 0) (layer "B.Fab") - (uuid "31677e5c-28e4-4666-b228-df51e5ab7257") + (uuid "190badc0-99f5-49cd-a801-6ac92a88ce63") (effects (font (size 1 1) @@ -15929,7 +15104,7 @@ (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "ec7b95dc-676c-4986-b4dc-dd66c82d992c") + (uuid "7b4601c3-c924-4127-b3be-b9bb1649965d") (effects (font (size 1.27 1.27) @@ -15937,11 +15112,11 @@ (justify mirror) ) ) - (property "Description" "" + (property "Description" "Resistor" (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "1892e3b4-a7a3-493c-8f19-668d67356e3a") + (uuid "21fd61b7-ba14-4557-8eb9-87911032e0db") (effects (font (size 1.27 1.27) @@ -15953,7 +15128,7 @@ (at 0 0 0) (layer "B.SilkS") (hide yes) - (uuid "c7904181-74b3-47bd-aeee-c76eaa78b9c8") + (uuid "e56b6423-b735-4b62-8de2-66bbafe97e02") (effects (font (size 1 1) @@ -15962,146 +15137,156 @@ (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 0) - (layer "B.SilkS") + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "02cb9ee3-038f-41db-a8ac-734a63a70e9b") + (uuid "4c1b962c-a5a4-4e5d-a4ab-71b5f04db3f0") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 -2 0) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "0402WGF1003TCE" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "8d2cf348-7803-427a-af9e-5127201556b2") + (uuid "0bbe58cd-aaee-48b1-a033-14b668473729") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C1525" - (at 0 -2 0) - (layer "B.SilkS") + (property "LCSC" "C25741" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "5af47887-fad1-41c2-bfd2-abfa586b198a") + (uuid "6358ea15-bb81-4fe5-8420-e682c1f852db") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Path" "C_TRIG1" - (at 0 -2 0) + (property "Stackup Path" "R_PWR_EN_PD1" + (at -2 0 270) (layer "B.SilkS") (hide yes) - (uuid "a5bdac34-608e-4ebc-a5f7-043d07538243") + (uuid "b70a2881-d213-474f-a221-d15e5fed45c0") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:102" - (at 0 -2 0) + (property "Stackup Source" "@stackup/passives.kdl:126" + (at -2 0 270) (layer "B.SilkS") (hide yes) - (uuid "d22a85aa-50c6-4100-8cb4-8683599ae546") + (uuid "a1525269-e758-4655-8b66-373e77e6ac77") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (path "/f3b6ba4d-8858-5241-8647-ebaa5466f9f2") + (property ki_fp_filters "R_*") + (path "/e49fe592-c225-51f5-816f-a451f2a1b535") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "c407f862-c614-4452-80af-0369c6b21fed") + (uuid "2a3cdd9b-d0ac-484f-b280-b11bfbf2c4ee") ) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "35753784-67fc-4ae2-abe2-f294d4d78a64") + (uuid "f8c2000c-4367-4d59-85e3-dfdcf0d0aad1") ) (fp_rect - (start -0.91 0.46) - (end 0.91 -0.46) + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "B.CrtYd") - (uuid "54f6352c-1946-4564-ace5-07e490fe7dc7") + (uuid "066d8fe9-5a65-45f9-ae86-b99d5ddbf8ad") ) (fp_rect - (start -0.5 0.25) - (end 0.5 -0.25) + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "0afed501-bbcf-4ea0-b2d1-9129291908aa") + (uuid "7c44618f-b498-4288-be0f-9f8227c2448c") ) (fp_text user "${REFERENCE}" (at 0 0 0) (layer "B.Fab") - (uuid "7125f04d-c78f-443b-afe2-85690d1dddd1") + (uuid "f22346ee-4b90-40ec-b714-24ca4ff64433") (effects (font - (size 0.25 0.25) + (size 0.26 0.26) (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.48 0 180) - (size 0.56 0.62) + (at -0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Hall_Trigger/TRIG_ADC") - (uuid "36edfd92-46b9-4e21-9c0a-faeb453c6cc1") + (net "/Power_Buck/PWR_EN") + (pintype "passive") + (uuid "def0862f-a50c-4f4b-a0a5-d81ead21058c") ) (pad "2" smd roundrect - (at 0.48 0 180) - (size 0.56 0.62) + (at 0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) (net "GND") - (uuid "b0facdce-0334-47d0-a9bf-63291bdf031c") + (pintype "passive") + (uuid "af485da4-8949-4169-ba54-20897de03dd2") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -16113,17 +15298,17 @@ ) ) ) - (footprint "L_0603_1608Metric" + (footprint "Fiducial:Fiducial_1mm_Mask2mm" (layer "B.Cu") - (uuid "42a58871-51ca-4657-bb67-94c70e434ee8") - (at 139.825 91.375) - (descr "Inductor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: http://www.tortai-tech.com/upload/download/2011102023233369053.pdf)") - (tags "inductor") - (property "Reference" "FB_RF1" - (at 0 1.43 180) + (uuid "3f4e415c-2019-4bf1-a307-2d92c8ec5904") + (at 122.75 128.25) + (descr "Fiducial, circular marking, 1mm bare copper, 2mm soldermask opening") + (tags "fiducial") + (property "Reference" "FID5" + (at 0 -1.95 0) (layer "B.SilkS") (hide yes) - (uuid "71cb1d34-0cf9-4e8a-b823-2db147058ab8") + (uuid "21b106c5-de31-4725-86b3-da18830ce282") (effects (font (size 1 1) @@ -16132,10 +15317,11 @@ (justify mirror) ) ) - (property "Value" "600Ω@100MHz" - (at 0 -1.43 180) + (property "Value" "Fiducial_1mm_Mask2mm" + (at 0 1.95 0) (layer "B.Fab") - (uuid "3e8d4b9d-ff34-403e-b44b-a0172bb476af") + (hide yes) + (uuid "501f247d-0e52-4f62-9920-bcb96cd8421e") (effects (font (size 1 1) @@ -16145,197 +15331,43 @@ ) ) (property "Datasheet" "" - (at 0 0 180) - (layer "B.Fab") + (at 0 0 0) + (layer "F.Fab") (hide yes) - (uuid "57bc49b1-bbee-4f8c-93bd-c53cb99eafaf") + (uuid "2112655d-6cb2-496f-aac0-d8e1a61d6454") (effects (font (size 1.27 1.27) ) - (justify mirror) ) ) (property "Description" "" - (at 0 0 180) - (layer "B.Fab") - (hide yes) - (uuid "dcb03124-c8be-480e-acc8-aac0b433fb7b") - (effects - (font - (size 1.27 1.27) - ) - (justify mirror) - ) - ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 180) - (layer "B.SilkS") - (hide yes) - (uuid "cb197a5e-5528-4e5a-bb14-5218295b7c6a") - (effects - (font - (size 1 1) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "MF" "Murata" - (at 0 -2 180) - (layer "B.SilkS") - (hide yes) - (uuid "2d4b4259-59ee-44a4-a662-34c47e3ac4ee") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Manufacturer_Part_Number" "BLM18KG601SN1D" - (at 0 -2 180) - (layer "B.SilkS") - (hide yes) - (uuid "19dc8abb-0a4b-416d-8574-39216bf9c83e") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "LCSC" "C85833" - (at 0 -2 180) - (layer "B.SilkS") - (hide yes) - (uuid "69e5b884-b897-4252-bd16-75a58a0972ef") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Path" "FB_RF1" - (at 0 -2 180) - (layer "B.SilkS") - (hide yes) - (uuid "c5574baf-023c-4b26-8661-e6388d390860") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:93" - (at 0 -2 180) - (layer "B.SilkS") + (at 0 0 0) + (layer "F.Fab") (hide yes) - (uuid "c4856ae5-a8f8-4235-96e0-be45af66c95a") + (uuid "643c9ba5-ebeb-4d56-aa92-063cd66ebb31") (effects (font (size 1.27 1.27) - (thickness 0.15) ) - (justify mirror) ) ) - (path "/b2659d47-21a7-5495-9164-d4d5931ac300") - (attr smd) + (attr smd board_only exclude_from_bom) (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.162779 -0.51) - (end 0.162779 -0.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "a64fb9af-13f0-4ae2-9384-22f1be15083c") - ) - (fp_line - (start -0.162779 0.51) - (end 0.162779 0.51) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "e8c1c160-60e9-4258-a93b-694c7c369ac7") - ) - (fp_rect - (start -1.48 0.73) - (end 1.48 -0.73) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "B.CrtYd") - (uuid "735e2b3a-60bc-481d-9ecb-0eac5ef4cbbd") - ) - (fp_rect - (start -0.8 0.4) - (end 0.8 -0.4) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "B.Fab") - (uuid "4524353f-b545-49ba-b77f-521ad784f43d") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) - (layer "B.Fab") - (uuid "96bc9f00-f173-4d2f-b9df-2aee908783a2") - (effects - (font - (size 0.4 0.4) - (thickness 0.06) - ) - (justify mirror) - ) - ) - (pad "1" smd roundrect - (at -0.7875 0) - (size 0.875 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "3V3") - (uuid "5d3f5a60-cbcf-4934-800e-6be6bac2136d") - ) - (pad "2" smd roundrect - (at 0.7875 0) - (size 0.875 0.95) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") - (uuid "451ecc3e-05d3-4bd4-8491-16db0d7b742a") + (pad "" smd circle + (at 0 0) + (size 1 1) + (layers "B.Cu" "B.Mask") + (solder_mask_margin 0.5) + (clearance 0.6) + (uuid "a813db40-9e4e-468a-a73b-158291e52110") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Inductor_SMD.3dshapes/L_0603_1608Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) ) (footprint "LOGO" (layer "B.Cu") (uuid "43777110-603b-42ec-9145-81e8566f267d") - (at 123.2 67.2) + (at 130.6 110.6) (property "Reference" "LOGO1" (at 0 0 0) (layer "B.SilkS") @@ -18973,14 +18005,14 @@ (footprint "LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y" (layer "B.Cu") (uuid "4c0f07af-4e0e-4c3e-a5f5-91899a0cb8e1") - (at 144.7 67.8 180) + (at 129.8125 127.2625 -90) (descr "LGA, 14 Pin (https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdf)") (tags "LGA NoLead") (property "Reference" "U_IMU1" - (at 0 2.2 0) + (at 0 2.2 90) (layer "B.SilkS") (hide yes) - (uuid "877b5295-e9c8-4482-b3aa-0f2b721da8ea") + (uuid "7d2ee472-0178-4d16-b660-981aaad1a4ba") (effects (font (size 1 1) @@ -18990,9 +18022,9 @@ ) ) (property "Value" "ICM-42670-P" - (at 0 -2.2 0) + (at 0 -2.2 90) (layer "B.Fab") - (uuid "89468e8f-82ec-412c-94ea-e35f217bc76f") + (uuid "384f2065-eed5-4187-83d3-8a26fb34295a") (effects (font (size 1 1) @@ -19002,10 +18034,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "56c0b2ba-db2d-4eb2-bb83-063da9d83094") + (uuid "cabde593-c29a-4cb2-8744-9176307c8058") (effects (font (size 1.27 1.27) @@ -19014,10 +18046,10 @@ ) ) (property "Description" "" - (at 0 0 0) + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "9ebc2d16-1a45-40c6-adcb-17a49532fc77") + (uuid "a9b86919-daa5-44ad-9ece-f64a6ffe1959") (effects (font (size 1.27 1.27) @@ -19026,7 +18058,7 @@ ) ) (property "KiLib_Generator" "package/no_lead" - (at 0 0 0) + (at 0 0 90) (layer "B.SilkS") (hide yes) (uuid "c26d6c20-3ea6-4fad-998a-eb285aa324a1") @@ -19039,7 +18071,7 @@ ) ) (property "MF" "TDK InvenSense" - (at 0 -2 0) + (at 0 -2 90) (layer "B.SilkS") (hide yes) (uuid "5e79537b-ba46-434c-97af-e0731842072d") @@ -19052,7 +18084,7 @@ ) ) (property "Manufacturer_Part_Number" "ICM-42670-P" - (at 0 -2 0) + (at 0 -2 90) (layer "B.SilkS") (hide yes) (uuid "9ad3f690-9b6e-48a7-bf5b-845a0a71f217") @@ -19065,7 +18097,7 @@ ) ) (property "LCSC" "C3288646" - (at 0 -2 0) + (at 0 -2 90) (layer "B.SilkS") (hide yes) (uuid "37090d2a-0376-467a-8c5a-a463b3096f24") @@ -19078,7 +18110,7 @@ ) ) (property "Stackup Path" "U_IMU1" - (at 0 -2 0) + (at 0 -2 90) (layer "B.SilkS") (hide yes) (uuid "d9714eb5-29cf-4d6d-bc6b-2e3750c7e8a5") @@ -19090,8 +18122,8 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:106" - (at 0 -2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:107" + (at 0 -2 90) (layer "B.SilkS") (hide yes) (uuid "3aa18811-53df-495c-84e1-ff6d8573358c") @@ -19107,84 +18139,84 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start 1.61 1.36) - (end 1.61 1.185) + (start -1.61 1.36) + (end -0.935 1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "9444ae8b-d374-4c60-85dc-4a6f68c633bc") + (uuid "4c99b387-d4ec-48f6-8e9c-97e216990939") ) (fp_line - (start 1.61 -1.185) - (end 1.61 -1.36) + (start 0.935 1.36) + (end 1.61 1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "5b3187dd-3362-4389-bf55-80aac83f27c5") + (uuid "21223aa1-d1a6-48ae-a7d0-759a206d6bd8") ) (fp_line - (start 1.61 -1.36) - (end 0.935 -1.36) + (start 1.61 1.36) + (end 1.61 1.185) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "c57811db-fddf-4323-b0d9-867b432e03cd") + (uuid "9444ae8b-d374-4c60-85dc-4a6f68c633bc") ) (fp_line - (start 0.935 1.36) - (end 1.61 1.36) + (start -1.61 1.185) + (end -1.61 1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "21223aa1-d1a6-48ae-a7d0-759a206d6bd8") + (uuid "a067dca7-4b4f-4507-a061-a3918764ca54") ) (fp_line - (start -0.935 -1.36) - (end -1.61 -1.36) + (start 1.61 -1.185) + (end 1.61 -1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "8d222c5e-cece-45a0-a227-25d699798ae5") + (uuid "5b3187dd-3362-4389-bf55-80aac83f27c5") ) (fp_line - (start -1.61 1.36) - (end -0.935 1.36) + (start -1.61 -1.36) + (end -1.61 -1.185) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "4c99b387-d4ec-48f6-8e9c-97e216990939") + (uuid "28baa91d-b795-4fe8-88f3-7c69fb5e55b9") ) (fp_line - (start -1.61 1.185) - (end -1.61 1.36) + (start -0.935 -1.36) + (end -1.61 -1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "a067dca7-4b4f-4507-a061-a3918764ca54") + (uuid "8d222c5e-cece-45a0-a227-25d699798ae5") ) (fp_line - (start -1.61 -1.36) - (end -1.61 -1.185) + (start 1.61 -1.36) + (end 0.935 -1.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "28baa91d-b795-4fe8-88f3-7c69fb5e55b9") + (uuid "c57811db-fddf-4323-b0d9-867b432e03cd") ) (fp_poly (pts @@ -19222,7 +18254,7 @@ (uuid "5eec0b86-31db-4507-a76e-363b2a138ffd") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 90) (layer "B.Fab") (uuid "e1bfaae2-aef2-417d-9331-9ff4714634e6") (effects @@ -19234,7 +18266,7 @@ ) ) (pad "1" smd roundrect - (at -1.1625 0.75 180) + (at -1.1625 0.75 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19242,7 +18274,7 @@ (uuid "8ba4c58a-7524-4e79-82f4-e04fe1938fe1") ) (pad "2" smd roundrect - (at -1.1625 0.25 180) + (at -1.1625 0.25 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19250,7 +18282,7 @@ (uuid "95628c49-02c9-42c9-b8b4-7a461a2f0cbc") ) (pad "3" smd roundrect - (at -1.1625 -0.25 180) + (at -1.1625 -0.25 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19258,7 +18290,7 @@ (uuid "4fce749c-3ea2-407a-8151-1918f59def04") ) (pad "4" smd roundrect - (at -1.1625 -0.75 180) + (at -1.1625 -0.75 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19266,7 +18298,7 @@ (uuid "a6568902-4c26-4a4f-aa93-d594e0b475b8") ) (pad "5" smd roundrect - (at -0.5 -0.9125 180) + (at -0.5 -0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19274,7 +18306,7 @@ (uuid "6f50b715-e504-4135-9392-c8c38e8ba488") ) (pad "6" smd roundrect - (at 0 -0.9125 180) + (at 0 -0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19282,7 +18314,7 @@ (uuid "959e242d-7587-40e3-a7c2-bbc39e2a38fc") ) (pad "7" smd roundrect - (at 0.5 -0.9125 180) + (at 0.5 -0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19290,7 +18322,7 @@ (uuid "e870be6c-47eb-4d34-88dd-6cbee3071b38") ) (pad "8" smd roundrect - (at 1.1625 -0.75 180) + (at 1.1625 -0.75 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19298,14 +18330,14 @@ (uuid "f2822518-63e2-4f54-9bef-a33d50e8ef14") ) (pad "9" smd roundrect - (at 1.1625 -0.25 180) + (at 1.1625 -0.25 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) (uuid "487a2e04-3884-4030-a89f-466677d55819") ) (pad "10" smd roundrect - (at 1.1625 0.25 180) + (at 1.1625 0.25 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19313,7 +18345,7 @@ (uuid "a0ebe3cb-3342-4ed6-b601-4620d3c2da37") ) (pad "11" smd roundrect - (at 1.1625 0.75 180) + (at 1.1625 0.75 270) (size 0.625 0.35) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19321,7 +18353,7 @@ (uuid "60109a9c-6b12-4db0-abaf-d6924ef7260c") ) (pad "12" smd roundrect - (at 0.5 0.9125 180) + (at 0.5 0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19329,7 +18361,7 @@ (uuid "845d03bf-58cf-4995-950d-fd980ef7662b") ) (pad "13" smd roundrect - (at 0 0.9125 180) + (at 0 0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19337,7 +18369,7 @@ (uuid "102c2247-4df8-4cde-a756-dcf8181332f1") ) (pad "14" smd roundrect - (at -0.5 0.9125 180) + (at -0.5 0.9125 270) (size 0.35 0.625) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -19357,6 +18389,222 @@ ) ) ) + (footprint "Capacitor_SMD:C_0805_2012Metric" + (layer "B.Cu") + (uuid "4e10f49e-2dcc-4c78-9962-5b2c41ec36bf") + (at 146.5 90.6 90) + (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (tags "capacitor") + (property "Reference" "C_BUCK_IN1" + (at 0 1.68 90) + (layer "B.SilkS") + (hide yes) + (uuid "023e560f-cab2-4cec-9c89-7a1ae3d6ea74") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Value" "10µF" + (at 0 -1.68 90) + (layer "B.Fab") + (uuid "248c280c-de87-40b8-8254-606146450ed9") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Datasheet" "" + (at 0 0 90) + (layer "B.Fab") + (hide yes) + (uuid "d6c82177-c5b6-4ff6-a553-0d916b0002ab") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "Description" "Unpolarized capacitor" + (at 0 0 90) + (layer "B.Fab") + (hide yes) + (uuid "a9201686-5b28-4e4d-8f99-92ac80616fb7") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "MF" "Samsung Electro-Mechanics" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "0d92eea3-6382-4561-80fd-d4130f6e6138") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "fa6e0712-5f41-4b68-b84f-36fcf341bf46") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "LCSC" "C15850" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "123c97d9-47f5-4b56-898e-634f2fe303ac") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Stackup Path" "C_BUCK_IN1" + (at 0 -2 90) + (layer "B.SilkS") + (hide yes) + (uuid "7a91119b-5282-4cce-966d-768c9aac5324") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:25" + (at 0 -2 90) + (layer "B.SilkS") + (hide yes) + (uuid "d12f8c26-3e7d-4139-8511-9ddbef7ac3d7") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "C_*") + (path "/d5366359-0189-584f-bdba-ca23d6aa7d16") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.261252 -0.735) + (end 0.261252 -0.735) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "8a970c10-a955-433b-91ab-5cbc861a9f42") + ) + (fp_line + (start -0.261252 0.735) + (end 0.261252 0.735) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "8cd131c5-a571-4852-a5c3-2a5bf9506838") + ) + (fp_rect + (start -1.7 0.98) + (end 1.7 -0.98) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "B.CrtYd") + (uuid "eddc8c1b-5147-4431-a679-2aa96cac0b95") + ) + (fp_rect + (start -1 0.625) + (end 1 -0.625) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "B.Fab") + (uuid "f4d996e5-8d52-4f68-a726-6dd911b40aca") + ) + (fp_text user "${REFERENCE}" + (at 0 0 90) + (layer "B.Fab") + (uuid "6036687a-6def-4d1b-80d5-38cadc3d6755") + (effects + (font + (size 0.5 0.5) + (thickness 0.08) + ) + (justify mirror) + ) + ) + (pad "1" smd roundrect + (at -0.95 0 90) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "VSYS") + (pintype "passive") + (uuid "69b83c4f-9be7-48ea-9ffe-f8da0c826497") + ) + (pad "2" smd roundrect + (at 0.95 0 90) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "2b613f3c-9fd5-4662-a95c-903c2ef2b3e5") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "B.Cu") (uuid "4e27a88d-92dc-4ad8-a165-91c4850ee113") @@ -19479,7 +18727,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:31" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:33" (at 2 0 270) (layer "B.SilkS") (hide yes) @@ -19589,14 +18837,14 @@ (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "B.Cu") (uuid "5afd9c51-ad9d-481b-b003-54bbbb6854d6") - (at 128.8 64.6) + (at 129.42 63.8) (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") (property "Reference" "C_HALL1" (at 0 1.16 0) (layer "B.SilkS") (hide yes) - (uuid "fcd5da2c-62a3-4024-8450-439defd15ad5") + (uuid "ed38b240-3cdb-450b-9810-659c9951095f") (effects (font (size 1 1) @@ -19608,7 +18856,7 @@ (property "Value" "100nF" (at 0 -1.16 0) (layer "B.Fab") - (uuid "3681de8c-af85-421b-a828-5ca8c7b8781d") + (uuid "afda0a1f-716e-41d3-8ca9-61eae7949c8a") (effects (font (size 1 1) @@ -19621,7 +18869,7 @@ (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "dbb00896-8dd2-4af0-bd77-ae36fbaec392") + (uuid "05cfa617-1396-4970-9446-042d874bbd4e") (effects (font (size 1.27 1.27) @@ -19633,7 +18881,7 @@ (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "cc5451d1-49a4-4cb9-9218-94c9c6060b1d") + (uuid "8b55a7df-3291-49ab-84a0-f642e7685c97") (effects (font (size 1.27 1.27) @@ -19695,7 +18943,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:30" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:32" (at 0 -2 0) (layer "B.SilkS") (hide yes) @@ -19776,7 +19024,7 @@ (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") + (net "3V3") (pintype "passive") (uuid "516947fa-0031-4bd5-ace4-fe1b9b78b82d") ) @@ -19924,7 +19172,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:60" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:63" (at 0 -2 0) (layer "B.SilkS") (hide yes) @@ -20145,7 +19393,7 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:84" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:87" (at 0 2 0) (layer "B.SilkS") (hide yes) @@ -20612,7 +19860,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:61" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:64" (at -2 0 0) (layer "B.SilkS") (hide yes) @@ -20828,7 +20076,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:59" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:62" (at 0 -2 270) (layer "B.SilkS") (hide yes) @@ -21044,7 +20292,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:51" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:53" (at 0 2 270) (layer "B.SilkS") (hide yes) @@ -21374,29 +20622,29 @@ ) ) ) - (footprint "Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical" + (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "B.Cu") - (uuid "6a9bd7ef-c169-4f03-8e77-01e07b2f508f") - (at 146.3 112.235 90) - (descr "Tag-Connect programming header; http://www.tag-connect.com/Materials/TC2030-IDC-NL.pdf") - (tags "tag connect programming header pogo pins") - (property "Reference" "J_SWD1" - (at 0 -2.7 90) + (uuid "6c065ac4-f64b-4312-bde9-e1c4595b72fa") + (at 131.25 94.73 -90) + (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "capacitor") + (property "Reference" "C_SYS_2" + (at 0 1.16 270) (layer "B.SilkS") (hide yes) - (uuid "accd3cea-89a6-4558-af20-c6df923bf636") + (uuid "9537b2d9-04c1-4bb4-968b-064284a132d2") (effects (font - (size 0.8 0.8) - (thickness 0.12) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "Value" "TC2030-NL" - (at -1.675 7.85 90) + (property "Value" "100nF" + (at 0 -1.16 270) (layer "B.Fab") - (uuid "c12a727f-fbd4-416e-8b8b-af7e85ab51da") + (uuid "51e5f2c8-7140-4978-af3a-5690f99018b2") (effects (font (size 1 1) @@ -21407,272 +20655,197 @@ ) (property "Datasheet" "" (at 0 0 270) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "9c179ca0-e293-42d0-8bf6-7d0a70e3023f") + (uuid "a53a392f-8223-41b9-aa5a-49ad740c19ec") (effects (font (size 1.27 1.27) - (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "" + (property "Description" "Unpolarized capacitor" (at 0 0 270) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "22b164a4-809d-4dc7-a6ef-f4e3300aef59") + (uuid "2fae936d-defa-4080-8588-17ab4e1bab63") (effects (font (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "MF" "Samsung Electro-Mechanics" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "8ec8f803-2729-42b8-b115-8c328158c379") + (effects + (font + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "None" - (at 0 -2 90) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "52b8ce57-9e11-4734-b940-ca73b2e14abd") + (uuid "cccc6388-0134-4240-87a0-c17d1f7d9b32") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "Copper pad, no part" - (at 0 -2 90) - (layer "B.SilkS") + (property "LCSC" "C1525" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "2829e707-b316-437a-9976-506b11dae21e") + (uuid "4b4fbbef-6501-43d2-9918-84529b4813d9") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Path" "J_SWD1" - (at 0 -2 90) + (property "Stackup Path" "C_SYS_2" + (at 2 0 180) (layer "B.SilkS") (hide yes) - (uuid "58c0a589-c35a-4a3e-ab1d-958dd873949d") + (uuid "cbbb5024-eba7-432a-9f6c-ad412f43fb74") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:97" - (at 0 -2 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:39" + (at 2 0 180) (layer "B.SilkS") (hide yes) - (uuid "dcc7d8cf-b5f1-47af-b493-7af2892e6306") + (uuid "56705001-f4f7-44f0-8a76-bd986d316c30") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (path "/1a69035a-00cc-58a8-be04-81511744d80c") - (attr exclude_from_pos_files exclude_from_bom) + (property ki_fp_filters "C_*") + (path "/e2c8fc08-1aa6-5675-9020-a7b835e59054") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -1.27 -1.27) - (end -1.905 -1.27) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "da54208b-04b2-4322-8b0c-b1b68d6fc8e7") + (uuid "13541b1a-7867-43cd-bec1-b269b037414c") ) (fp_line - (start -1.905 -1.27) - (end -1.905 -0.635) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "ffc3d697-a117-46b5-85ff-f6c21a63c352") - ) - (fp_line - (start 3.5 -2) - (end -3.5 -2) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "7c4e4c98-41cf-40d7-8280-96eb27a60b4f") - ) - (fp_line - (start -3.5 -2) - (end -3.5 2) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "7c02ec12-e10c-4e12-bee3-11077cef10f0") + (uuid "a0d76405-9be5-4fbc-ab2f-69fa5d4d815f") ) - (fp_line - (start 3.5 2) - (end 3.5 -2) + (fp_rect + (start -0.91 0.46) + (end 0.91 -0.46) (stroke (width 0.05) (type solid) ) + (fill no) (layer "B.CrtYd") - (uuid "cc9f4457-3d5d-40ac-b2a1-1e16c436d4ba") + (uuid "68484eac-d015-4ccd-b789-c17b315171b0") ) - (fp_line - (start -3.5 2) - (end 3.5 2) + (fp_rect + (start -0.5 0.25) + (end 0.5 -0.25) (stroke - (width 0.05) + (width 0.1) (type solid) ) - (layer "B.CrtYd") - (uuid "6deba30b-8d70-4101-9c57-6c3fcf6b1ba7") - ) - (fp_text user "KEEPOUT" - (at 0 0 90) - (layer "Cmts.User") - (uuid "f0ca91dd-6f71-4621-bfc7-cab90c4bb322") - (effects - (font - (size 0.4 0.4) - (thickness 0.07) - ) - ) + (fill no) + (layer "B.Fab") + (uuid "7bd128d4-e869-402d-87d3-a92fe78051f5") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 270) (layer "B.Fab") - (uuid "b9f48c63-27c6-41a7-98be-2d3efc2c859c") + (uuid "317a5d3b-afa4-4a1e-9207-a7cd367d9f7d") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.25 0.25) + (thickness 0.04) ) (justify mirror) ) ) - (pad "" np_thru_hole circle - (at -2.54 0 90) - (size 0.9906 0.9906) - (drill 0.9906) - (layers "*.Cu" "*.Mask") - (uuid "4830db45-ce87-4771-8d50-bff9ad55b650") - ) - (pad "" np_thru_hole circle - (at 2.54 -1.016 90) - (size 0.9906 0.9906) - (drill 0.9906) - (layers "*.Cu" "*.Mask") - (uuid "f72602c7-f9f4-4208-b8b8-ca3c104c5fae") - ) - (pad "" np_thru_hole circle - (at 2.54 1.016 90) - (size 0.9906 0.9906) - (drill 0.9906) - (layers "*.Cu" "*.Mask") - (uuid "45100e17-7f8c-46f3-a71e-03b05f2f94f8") - ) - (pad "1" connect circle - (at -1.27 -0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") - (net "3V3") - (uuid "8dcea226-678e-4591-bebe-636b4b263dba") - ) - (pad "2" connect circle - (at -1.27 0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") - (net "/MCU_Core/SWDIO") - (uuid "bdbd822a-64c0-4006-82fa-df71e901d994") - ) - (pad "3" connect circle - (at 0 -0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") - (net "/MCU_Core/MCU_RESET") - (uuid "6ededa66-8c1d-4e30-a05a-985df9b0ff22") - ) - (pad "4" connect circle - (at 0 0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") - (net "/MCU_Core/SWDCLK") - (uuid "7cafa9bd-8c2e-4f08-b625-10b87b7918c1") + (pad "1" smd roundrect + (at -0.48 0 270) + (size 0.56 0.62) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "VSYS") + (pintype "passive") + (uuid "d0925c20-c808-4901-a072-2ae07f61bad6") ) - (pad "5" connect circle - (at 1.27 -0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") + (pad "2" smd roundrect + (at 0.48 0 270) + (size 0.56 0.62) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) (net "GND") - (uuid "57da8fb9-0042-4091-8ec8-98d8d4bba860") - ) - (pad "6" connect circle - (at 1.27 0.635 90) - (size 0.7874 0.7874) - (layers "B.Cu" "B.Mask") - (uuid "5d74daa0-c6cb-4944-84d1-749d4f8730a9") + (pintype "passive") + (uuid "2ab3e196-cfee-49bf-9884-10a466fa28dd") ) - (zone - (layer "B.Cu") - (uuid "2a96b864-899f-4779-8afc-04e2c62057f8") - (hatch full 0.508) - (connect_pads - (clearance 0) - ) - (min_thickness 0.254) - (keepout - (tracks allowed) - (vias not_allowed) - (pads allowed) - (copperpour not_allowed) - (footprints not_allowed) - ) - (placement - (enabled no) - (sheetname "") + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (offset + (xyz 0 0 0) ) - (fill - (thermal_gap 0.508) - (thermal_bridge_width 0.508) - (island_removal_mode 0) + (scale + (xyz 1 1 1) ) - (polygon - (pts - (xy 146.935 110.965) (xy 146.935 113.505) (xy 145.665 113.505) (xy 145.665 110.965) - ) + (rotate + (xyz 0 0 0) ) ) - (embedded_fonts no) ) (footprint "C_0603_1608Metric" (layer "B.Cu") (uuid "7772f596-d15e-412d-8234-24388bc2ff9e") - (at 140.75 69.25 -90) + (at 124.7 125.7 180) (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") (property "Reference" "C_IMU_2" - (at 0 1.43 90) + (at 0 1.43 0) (layer "B.SilkS") (hide yes) (uuid "0cecc8e1-02ea-49c4-abe7-552b90ef5d91") @@ -21685,7 +20858,7 @@ ) ) (property "Value" "2.2µF" - (at 0 -1.43 90) + (at 0 -1.43 0) (layer "B.Fab") (uuid "08f8b185-6527-4eda-b341-b662eb326681") (effects @@ -21697,7 +20870,7 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (hide yes) (uuid "65af47f0-b1f0-47da-854c-595dfdfafda4") @@ -21709,7 +20882,7 @@ ) ) (property "Description" "" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (hide yes) (uuid "12a80ba2-ce35-4b54-b7ba-fc3aa29130c3") @@ -21721,7 +20894,7 @@ ) ) (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 90) + (at 0 0 0) (layer "B.SilkS") (hide yes) (uuid "c45d9255-7862-45c1-a53b-b99e93a1f142") @@ -21734,7 +20907,7 @@ ) ) (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "de3d79d2-e9a5-4a31-ad46-7bf1366b923a") @@ -21747,7 +20920,7 @@ ) ) (property "Manufacturer_Part_Number" "CL10B225KP8NNNC" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "9c527ede-1658-4334-b7f9-4c5aa813354a") @@ -21760,7 +20933,7 @@ ) ) (property "LCSC" "C100082" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "a295aeda-827e-4fba-bb96-20cfd69f54c7") @@ -21773,7 +20946,7 @@ ) ) (property "Stackup Path" "C_IMU_2" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "2e54c1fc-3270-407e-8547-2eaea4940d23") @@ -21785,8 +20958,8 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:28" - (at 0 -2 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:30" + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "bab09416-2dee-40a3-925e-cf6b0957e6ce") @@ -21844,7 +21017,7 @@ (uuid "32c2ad45-af25-4187-b44f-fc6fe76c5ced") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (uuid "4296a904-5fb1-463f-b353-5583e6445ea0") (effects @@ -21856,7 +21029,7 @@ ) ) (pad "1" smd roundrect - (at -0.775 0 270) + (at -0.775 0 180) (size 0.9 0.95) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -21864,7 +21037,7 @@ (uuid "5c71e083-a244-4e83-86a7-fd4ddd2d0761") ) (pad "2" smd roundrect - (at 0.775 0 270) + (at 0.775 0 180) (size 0.9 0.95) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -21887,12 +21060,12 @@ (footprint "LOGO" (layer "B.Cu") (uuid "79f3e841-1602-49ca-83a2-17e700e030f9") - (at 123.1 115 180) + (at 146.2 108.2 180) (property "Reference" "LOGO2" (at 0 0 0) (layer "B.SilkS") (hide yes) - (uuid "7ed9b8a2-d778-4a45-a5c4-a8f8396eb6b5") + (uuid "34b1b227-438c-45c1-b7ae-5132f95b33f6") (effects (font (size 1.5 1.5) @@ -21905,7 +21078,7 @@ (at 0.75 0 0) (layer "B.SilkS") (hide yes) - (uuid "dc8ed5c2-b1d7-4c0e-90c4-f17160759b65") + (uuid "360d1194-f699-4aa7-8c7c-bbb8107331e7") (effects (font (size 1.5 1.5) @@ -21918,7 +21091,7 @@ (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "d320e1cd-b147-4a94-ba38-3ef986be2b28") + (uuid "345c846d-7cd2-4f0d-8c2f-47f2b4264dea") (effects (font (size 1.27 1.27) @@ -21930,7 +21103,7 @@ (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "a1cc47ad-2182-4496-9dcc-f9e79c35db1d") + (uuid "15429fad-342c-40c8-bab9-877b709365de") (effects (font (size 1.27 1.27) @@ -22057,29 +21230,281 @@ ) (embedded_fonts no) ) - (footprint "Resistor_SMD:R_0402_1005Metric" + (footprint "Capacitor_SMD:C_0805_2012Metric" (layer "B.Cu") - (uuid "89256378-8b06-45a3-9170-cc87240992e0") - (at 141.775 126.065) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_CC2" - (at 0 1.17 180) + (uuid "7c3e1bde-ed4c-4163-a923-82af23ae1287") + (at 133.2 97.75) + (descr "Capacitor SMD 0805 (2012 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf, https://docs.google.com/spreadsheets/d/1BsfQQcO9C6DZCsRaXUlFlo91Tg2WpOkGARC1WS5S8t0/edit?usp=sharing)") + (tags "capacitor") + (property "Reference" "C_BAT1" + (at 0 1.68 180) (layer "B.SilkS") (hide yes) - (uuid "5c8338be-ebc5-4278-a6be-6e5c0da5c6cf") + (uuid "c10a7e00-8276-4583-a2d6-037815246ffc") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Value" "10µF" + (at 0 -1.68 180) + (layer "B.Fab") + (uuid "749c8d9a-e32d-421f-bf57-c3ee34a4d812") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Datasheet" "" + (at 0 0 180) + (layer "B.Fab") + (hide yes) + (uuid "873e446a-728e-42db-b4d9-27f5c3127f8a") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "Description" "Unpolarized capacitor" + (at 0 0 180) + (layer "B.Fab") + (hide yes) + (uuid "b972fe71-db34-4246-abe9-96bb9b411b90") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "MF" "Samsung Electro-Mechanics" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "6c2e7b0d-81c9-424e-b800-5d3214baba9b") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Manufacturer_Part_Number" "CL21A106KAYNNNE" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "aba0e959-1a1d-465e-90c8-45e4fbf12314") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "LCSC" "C15850" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "1c86887f-f997-4fab-93a1-88dfdcad1cb3") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Stackup Path" "C_BAT1" + (at 0 2 180) + (layer "B.SilkS") + (hide yes) + (uuid "801866e9-25be-41b1-ade4-320126f18d7d") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:24" + (at 0 2 180) + (layer "B.SilkS") + (hide yes) + (uuid "79058ded-645d-467b-8e52-e745eb240519") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) + ) + (property ki_fp_filters "C_*") + (path "/53994c88-33fa-516a-9d64-2f0949cf1a73") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.261252 -0.735) + (end 0.261252 -0.735) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "d9e928c4-100b-42b9-b513-270d0ea83806") + ) + (fp_line + (start -0.261252 0.735) + (end 0.261252 0.735) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "f98e28b1-5af7-4261-a0dd-d6375cceaa78") + ) + (fp_rect + (start -1.7 0.98) + (end 1.7 -0.98) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "B.CrtYd") + (uuid "a242494c-fef1-4e58-8845-ae4c1152b650") + ) + (fp_rect + (start -1 0.625) + (end 1 -0.625) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "B.Fab") + (uuid "925473b7-2a42-4bda-a61c-e929c55545f7") + ) + (fp_text user "${REFERENCE}" + (at 0 0 180) + (layer "B.Fab") + (uuid "12df748f-8b5c-4667-a0ec-3cb8d5190dc9") + (effects + (font + (size 0.5 0.5) + (thickness 0.08) + ) + (justify mirror) + ) + ) + (pad "1" smd roundrect + (at -0.95 0) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "VBAT") + (pintype "passive") + (uuid "97810122-0162-4a84-b675-d47562c9c5e8") + ) + (pad "2" smd roundrect + (at 0.95 0) + (size 1 1.45) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "1f420529-9c3f-416d-991b-6bd2ece3a600") + ) + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0805_2012Metric.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) + ) + ) + (footprint "BQ25185DLHR:IC_BQ25185DLHR" + (layer "B.Cu") + (uuid "836984b6-78b1-47fe-abee-4e3e5d3947c9") + (at 128.75 96.25 180) + (property "Reference" "U_CHG1" + (at 1.625 2.385 180) + (layer "B.SilkS") + (hide yes) + (uuid "2f641c96-19e9-456c-a079-4588a1c17c8e") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Value" "BQ25185DLHR" + (at 3 0.48 180) + (layer "B.Fab") + (uuid "937d09f5-09df-4d6b-8572-16fb39cbd9a6") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Datasheet" "" + (at 0 0 180) + (layer "B.Fab") + (hide yes) + (uuid "96cab20e-4629-450a-9947-3832773ddea6") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) + ) + (property "Description" "1-cell, 1-A stand-alone linear battery charger with power path and solar input support" + (at 0 0 180) + (layer "B.Fab") + (hide yes) + (uuid "d9c65078-d834-4ff3-a90a-3c7453bb0539") (effects (font - (size 1 1) - (thickness 0.15) + (size 1.27 1.27) ) (justify mirror) ) ) - (property "Value" "5.1kΩ" - (at 0 -1.17 180) + (property "MF" "Texas Instruments" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") - (uuid "8b0626de-cc65-496e-9d52-18a867c5e8db") + (hide yes) + (uuid "35792020-4129-42f5-bb24-953453bc3238") (effects (font (size 1 1) @@ -22088,36 +21513,40 @@ (justify mirror) ) ) - (property "Datasheet" "" - (at 0 0 180) + (property "SNAPEDA_PACKAGE_ID" "124517" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "a6cc48f5-3542-4dc5-8957-db7e9d4dbc1c") + (uuid "d59e212a-22d4-46b8-9873-85040c5da429") (effects (font - (size 1.27 1.27) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "Resistor" - (at 0 0 180) + (property "CREATOR" "AMINA" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "2cbc6365-711d-4fca-a71f-ae644fcbc514") + (uuid "e957fd6b-78d6-470b-bc48-e933fb5a37d6") (effects (font - (size 1.27 1.27) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 180) + (property "Price" "None" + (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "07cc9a19-3221-4a46-832f-8f542f5f7aa9") + (uuid "4ca0f772-4a36-462e-b05c-23ad06e5053c") (effects (font (size 1 1) @@ -22126,12 +21555,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF5101TCE" - (at 0 0 180) + (property "Package" "WFDFN-10 Texas Instruments" + (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "ac9fd379-5884-4597-892a-0415c62d9c14") + (uuid "d0b02736-bfa7-4e3d-80a1-97cc94045708") (effects (font (size 1 1) @@ -22140,12 +21569,12 @@ (justify mirror) ) ) - (property "LCSC" "C25905" - (at 0 0 180) + (property "Check_prices" "https://www.snapeda.com/parts/BQ25185DLHR/Texas+Instruments/view-part/?ref=eda" + (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "85cfd0e9-01b9-4cf4-8773-c65e2fa66884") + (uuid "9b1188a6-64e1-43c1-a1fb-63848eadf0bf") (effects (font (size 1 1) @@ -22154,138 +21583,54 @@ (justify mirror) ) ) - (property "Stackup Path" "R_CC2" - (at 0 -2 180) - (layer "B.SilkS") + (property "STANDARD" "Manufacturer Recommendations" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "79251760-58e6-4231-8920-4ae145aea970") + (uuid "27d6abc6-8624-40de-98b7-55fe9527c3e6") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:56" - (at 0 -2 180) - (layer "B.SilkS") + (property "PARTREV" "OCTOBER 2023" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "10132a5e-3328-4bc5-8eac-60ab122be947") + (uuid "9f1dbd7f-213d-4068-bc06-c1edb7a0eff3") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property ki_fp_filters "R_*") - (path "/d76e910c-dbb9-5852-9273-faf8c594840e") - (units - (unit - (name "A") - (pins "1" "2") - ) - ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "d7f00a62-8534-40c0-b676-c5e7bb881045") - ) - (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "e6bc2a52-3425-462b-ba98-e74edf33eb30") - ) - (fp_rect - (start -0.93 0.47) - (end 0.93 -0.47) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "B.CrtYd") - (uuid "e3112f01-c3cd-4d45-b8a7-20951e7886af") - ) - (fp_rect - (start -0.525 0.27) - (end 0.525 -0.27) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "B.Fab") - (uuid "c458ab8d-80a3-424a-a7ac-33e0a77e6a57") - ) - (fp_text user "${REFERENCE}" - (at 0 0 180) + (property "VERIFIER" "" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") - (uuid "6fd48b24-4255-4a54-a0e7-d1593a174ff5") + (hide yes) + (uuid "66178d75-9239-4a3a-afd4-59448f0851a5") (effects (font - (size 0.26 0.26) - (thickness 0.04) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "/USB_C/USB_CC2") - (pintype "passive") - (uuid "ea9bffac-1736-41a8-83aa-a3685ef16deb") - ) - (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "GND") - (pintype "passive") - (uuid "696b96b9-731f-45af-8493-d73f061bfe9f") - ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) - ) - ) - (footprint "Capacitor_SMD:C_0402_1005Metric" - (layer "B.Cu") - (uuid "95523c4d-0933-4f70-a61c-4aaab9a448d6") - (at 123.48 105.2 180) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_OLED_2" - (at 0 1.16 0) - (layer "B.SilkS") + (property "SnapEDA_Link" "https://www.snapeda.com/parts/BQ25185DLHR/Texas+Instruments/view-part/?ref=snap" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "d80b4794-dcf9-4ee0-bf7b-351ab8377f15") + (uuid "d0350a09-dd0a-43e1-a20d-570dbbb65b3e") (effects (font (size 1 1) @@ -22294,10 +21639,12 @@ (justify mirror) ) ) - (property "Value" "100nF" - (at 0 -1.16 0) + (property "MP" "BQ25185DLHR" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") - (uuid "c3381d27-934b-4484-a096-c132580c9312") + (hide yes) + (uuid "042db2af-b233-4164-be70-998b4c27197d") (effects (font (size 1 1) @@ -22306,36 +21653,40 @@ (justify mirror) ) ) - (property "Datasheet" "" + (property "MAXIMUM_PACKAGE_HEIGHT" "0.8mm" (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "cb509595-c87c-487e-b2fd-90eb06a5bb47") + (uuid "282cea84-e82d-442c-a8eb-9f89a4d2ec74") (effects (font - (size 1.27 1.27) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "Unpolarized capacitor" + (property "Availability" "In Stock" (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "35bb09b9-dd8a-4af2-b592-77b03feac139") + (uuid "8f997946-42bf-4b9a-8082-c29c47137a56") (effects (font - (size 1.27 1.27) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" + (property "MANUFACTURER" "Texas Instruments" (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "b30e4ee3-f6d0-49cb-acc3-ed449b7897e2") + (uuid "d936b382-e49f-4267-ade0-387a3dadc50e") (effects (font (size 1 1) @@ -22344,12 +21695,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 0) + (property "Manufacturer_Part_Number" "BQ25185DLHR" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "1ee40a5e-5339-4883-9fae-96ad554da347") + (uuid "0620b229-c858-4a88-a509-f0d502384867") (effects (font (size 1 1) @@ -22358,12 +21709,12 @@ (justify mirror) ) ) - (property "LCSC" "C1525" - (at 0 0 0) + (property "LCSC" "C19725033" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "a30e22fb-6445-40cb-9b66-befc1bbdf56e") + (uuid "ab69d5d2-eeeb-4a2e-84fb-56471cf467a2") (effects (font (size 1 1) @@ -22372,116 +21723,688 @@ (justify mirror) ) ) - (property "Stackup Path" "C_OLED_2" - (at 0 2 0) + (property "Stackup Path" "U_CHG1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "e2a8b331-9f3d-4cef-a0fb-d0d654d8ef67") + (uuid "942c6526-d2c5-4606-97b7-75f29077e200") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:33" - (at 0 2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:91" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "bbf8fc70-0f5e-42fd-b80b-8c261686142e") + (uuid "10443bf1-9da8-4fbf-b274-0cdd37cabe12") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/2b27245f-94c1-541b-bbeb-0dca2eb4c3cc") + (path "/b840e28f-4d8e-5da5-89df-017c48c36ef1") (units (unit (name "A") - (pins "1" "2") + (pins "10" "9" "3" "4" "7" "8" "1" "2" "6" "11" "5") + ) + ) + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_poly + (pts + (xy 0.75 0.7) (xy 0.75 0.9) (xy 0.75 0.903) (xy 0.75 0.905) (xy 0.751 0.908) (xy 0.751 0.91) (xy 0.752 0.913) + (xy 0.752 0.915) (xy 0.753 0.918) (xy 0.754 0.92) (xy 0.755 0.923) (xy 0.757 0.925) (xy 0.758 0.927) + (xy 0.76 0.929) (xy 0.761 0.931) (xy 0.763 0.933) (xy 0.765 0.935) (xy 0.767 0.937) (xy 0.769 0.939) + (xy 0.771 0.94) (xy 0.773 0.942) (xy 0.775 0.943) (xy 0.777 0.945) (xy 0.78 0.946) (xy 0.782 0.947) + (xy 0.785 0.948) (xy 0.787 0.948) (xy 0.79 0.949) (xy 0.792 0.949) (xy 0.795 0.95) (xy 0.797 0.95) + (xy 0.8 0.95) (xy 1.3 0.95) (xy 1.303 0.95) (xy 1.305 0.95) (xy 1.308 0.949) (xy 1.31 0.949) (xy 1.313 0.948) + (xy 1.315 0.948) (xy 1.318 0.947) (xy 1.32 0.946) (xy 1.323 0.945) (xy 1.325 0.943) (xy 1.327 0.942) + (xy 1.329 0.94) (xy 1.331 0.939) (xy 1.333 0.937) (xy 1.335 0.935) (xy 1.337 0.933) (xy 1.339 0.931) + (xy 1.34 0.929) (xy 1.342 0.927) (xy 1.343 0.925) (xy 1.345 0.923) (xy 1.346 0.92) (xy 1.347 0.918) + (xy 1.348 0.915) (xy 1.348 0.913) (xy 1.349 0.91) (xy 1.349 0.908) (xy 1.35 0.905) (xy 1.35 0.903) + (xy 1.35 0.9) (xy 1.35 0.7) (xy 1.35 0.697) (xy 1.35 0.695) (xy 1.349 0.692) (xy 1.349 0.69) (xy 1.348 0.687) + (xy 1.348 0.685) (xy 1.347 0.682) (xy 1.346 0.68) (xy 1.345 0.677) (xy 1.343 0.675) (xy 1.342 0.673) + (xy 1.34 0.671) (xy 1.339 0.669) (xy 1.337 0.667) (xy 1.335 0.665) (xy 1.333 0.663) (xy 1.331 0.661) + (xy 1.329 0.66) (xy 1.327 0.658) (xy 1.325 0.657) (xy 1.323 0.655) (xy 1.32 0.654) (xy 1.318 0.653) + (xy 1.315 0.652) (xy 1.313 0.652) (xy 1.31 0.651) (xy 1.308 0.651) (xy 1.305 0.65) (xy 1.303 0.65) + (xy 1.3 0.65) (xy 0.8 0.65) (xy 0.797 0.65) (xy 0.795 0.65) (xy 0.792 0.651) (xy 0.79 0.651) (xy 0.787 0.652) + (xy 0.785 0.652) (xy 0.782 0.653) (xy 0.78 0.654) (xy 0.777 0.655) (xy 0.775 0.657) (xy 0.773 0.658) + (xy 0.771 0.66) (xy 0.769 0.661) (xy 0.767 0.663) (xy 0.765 0.665) (xy 0.763 0.667) (xy 0.761 0.669) + (xy 0.76 0.671) (xy 0.758 0.673) (xy 0.757 0.675) (xy 0.755 0.677) (xy 0.754 0.68) (xy 0.753 0.682) + (xy 0.752 0.685) (xy 0.752 0.687) (xy 0.751 0.69) (xy 0.751 0.692) (xy 0.75 0.695) (xy 0.75 0.697) + (xy 0.75 0.7) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "0d4b3c6f-8a1a-4441-b07b-cc1d04ddcc5e") + ) + (fp_poly + (pts + (xy 0.75 0.3) (xy 0.75 0.5) (xy 0.75 0.503) (xy 0.75 0.505) (xy 0.751 0.508) (xy 0.751 0.51) (xy 0.752 0.513) + (xy 0.752 0.515) (xy 0.753 0.518) (xy 0.754 0.52) (xy 0.755 0.523) (xy 0.757 0.525) (xy 0.758 0.527) + (xy 0.76 0.529) (xy 0.761 0.531) (xy 0.763 0.533) (xy 0.765 0.535) (xy 0.767 0.537) (xy 0.769 0.539) + (xy 0.771 0.54) (xy 0.773 0.542) (xy 0.775 0.543) (xy 0.777 0.545) (xy 0.78 0.546) (xy 0.782 0.547) + (xy 0.785 0.548) (xy 0.787 0.548) (xy 0.79 0.549) (xy 0.792 0.549) (xy 0.795 0.55) (xy 0.797 0.55) + (xy 0.8 0.55) (xy 1.3 0.55) (xy 1.303 0.55) (xy 1.305 0.55) (xy 1.308 0.549) (xy 1.31 0.549) (xy 1.313 0.548) + (xy 1.315 0.548) (xy 1.318 0.547) (xy 1.32 0.546) (xy 1.323 0.545) (xy 1.325 0.543) (xy 1.327 0.542) + (xy 1.329 0.54) (xy 1.331 0.539) (xy 1.333 0.537) (xy 1.335 0.535) (xy 1.337 0.533) (xy 1.339 0.531) + (xy 1.34 0.529) (xy 1.342 0.527) (xy 1.343 0.525) (xy 1.345 0.523) (xy 1.346 0.52) (xy 1.347 0.518) + (xy 1.348 0.515) (xy 1.348 0.513) (xy 1.349 0.51) (xy 1.349 0.508) (xy 1.35 0.505) (xy 1.35 0.503) + (xy 1.35 0.5) (xy 1.35 0.3) (xy 1.35 0.297) (xy 1.35 0.295) (xy 1.349 0.292) (xy 1.349 0.29) (xy 1.348 0.287) + (xy 1.348 0.285) (xy 1.347 0.282) (xy 1.346 0.28) (xy 1.345 0.277) (xy 1.343 0.275) (xy 1.342 0.273) + (xy 1.34 0.271) (xy 1.339 0.269) (xy 1.337 0.267) (xy 1.335 0.265) (xy 1.333 0.263) (xy 1.331 0.261) + (xy 1.329 0.26) (xy 1.327 0.258) (xy 1.325 0.257) (xy 1.323 0.255) (xy 1.32 0.254) (xy 1.318 0.253) + (xy 1.315 0.252) (xy 1.313 0.252) (xy 1.31 0.251) (xy 1.308 0.251) (xy 1.305 0.25) (xy 1.303 0.25) + (xy 1.3 0.25) (xy 0.8 0.25) (xy 0.797 0.25) (xy 0.795 0.25) (xy 0.792 0.251) (xy 0.79 0.251) (xy 0.787 0.252) + (xy 0.785 0.252) (xy 0.782 0.253) (xy 0.78 0.254) (xy 0.777 0.255) (xy 0.775 0.257) (xy 0.773 0.258) + (xy 0.771 0.26) (xy 0.769 0.261) (xy 0.767 0.263) (xy 0.765 0.265) (xy 0.763 0.267) (xy 0.761 0.269) + (xy 0.76 0.271) (xy 0.758 0.273) (xy 0.757 0.275) (xy 0.755 0.277) (xy 0.754 0.28) (xy 0.753 0.282) + (xy 0.752 0.285) (xy 0.752 0.287) (xy 0.751 0.29) (xy 0.751 0.292) (xy 0.75 0.295) (xy 0.75 0.297) + (xy 0.75 0.3) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "39f6ec7e-745d-4a7f-813e-55f5ddf50212") + ) + (fp_poly + (pts + (xy 0.75 -0.1) (xy 0.75 0.1) (xy 0.75 0.103) (xy 0.75 0.105) (xy 0.751 0.108) (xy 0.751 0.11) (xy 0.752 0.113) + (xy 0.752 0.115) (xy 0.753 0.118) (xy 0.754 0.12) (xy 0.755 0.123) (xy 0.757 0.125) (xy 0.758 0.127) + (xy 0.76 0.129) (xy 0.761 0.131) (xy 0.763 0.133) (xy 0.765 0.135) (xy 0.767 0.137) (xy 0.769 0.139) + (xy 0.771 0.14) (xy 0.773 0.142) (xy 0.775 0.143) (xy 0.777 0.145) (xy 0.78 0.146) (xy 0.782 0.147) + (xy 0.785 0.148) (xy 0.787 0.148) (xy 0.79 0.149) (xy 0.792 0.149) (xy 0.795 0.15) (xy 0.797 0.15) + (xy 0.8 0.15) (xy 1.3 0.15) (xy 1.303 0.15) (xy 1.305 0.15) (xy 1.308 0.149) (xy 1.31 0.149) (xy 1.313 0.148) + (xy 1.315 0.148) (xy 1.318 0.147) (xy 1.32 0.146) (xy 1.323 0.145) (xy 1.325 0.143) (xy 1.327 0.142) + (xy 1.329 0.14) (xy 1.331 0.139) (xy 1.333 0.137) (xy 1.335 0.135) (xy 1.337 0.133) (xy 1.339 0.131) + (xy 1.34 0.129) (xy 1.342 0.127) (xy 1.343 0.125) (xy 1.345 0.123) (xy 1.346 0.12) (xy 1.347 0.118) + (xy 1.348 0.115) (xy 1.348 0.113) (xy 1.349 0.11) (xy 1.349 0.108) (xy 1.35 0.105) (xy 1.35 0.103) + (xy 1.35 0.1) (xy 1.35 -0.1) (xy 1.35 -0.103) (xy 1.35 -0.105) (xy 1.349 -0.108) (xy 1.349 -0.11) + (xy 1.348 -0.113) (xy 1.348 -0.115) (xy 1.347 -0.118) (xy 1.346 -0.12) (xy 1.345 -0.123) (xy 1.343 -0.125) + (xy 1.342 -0.127) (xy 1.34 -0.129) (xy 1.339 -0.131) (xy 1.337 -0.133) (xy 1.335 -0.135) (xy 1.333 -0.137) + (xy 1.331 -0.139) (xy 1.329 -0.14) (xy 1.327 -0.142) (xy 1.325 -0.143) (xy 1.323 -0.145) (xy 1.32 -0.146) + (xy 1.318 -0.147) (xy 1.315 -0.148) (xy 1.313 -0.148) (xy 1.31 -0.149) (xy 1.308 -0.149) (xy 1.305 -0.15) + (xy 1.303 -0.15) (xy 1.3 -0.15) (xy 0.8 -0.15) (xy 0.797 -0.15) (xy 0.795 -0.15) (xy 0.792 -0.149) + (xy 0.79 -0.149) (xy 0.787 -0.148) (xy 0.785 -0.148) (xy 0.782 -0.147) (xy 0.78 -0.146) (xy 0.777 -0.145) + (xy 0.775 -0.143) (xy 0.773 -0.142) (xy 0.771 -0.14) (xy 0.769 -0.139) (xy 0.767 -0.137) (xy 0.765 -0.135) + (xy 0.763 -0.133) (xy 0.761 -0.131) (xy 0.76 -0.129) (xy 0.758 -0.127) (xy 0.757 -0.125) (xy 0.755 -0.123) + (xy 0.754 -0.12) (xy 0.753 -0.118) (xy 0.752 -0.115) (xy 0.752 -0.113) (xy 0.751 -0.11) (xy 0.751 -0.108) + (xy 0.75 -0.105) (xy 0.75 -0.103) (xy 0.75 -0.1) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "bf0d7d86-821f-4d0d-9f68-e1ab9c42582a") + ) + (fp_poly + (pts + (xy 0.75 -0.5) (xy 0.75 -0.3) (xy 0.75 -0.297) (xy 0.75 -0.295) (xy 0.751 -0.292) (xy 0.751 -0.29) + (xy 0.752 -0.287) (xy 0.752 -0.285) (xy 0.753 -0.282) (xy 0.754 -0.28) (xy 0.755 -0.277) (xy 0.757 -0.275) + (xy 0.758 -0.273) (xy 0.76 -0.271) (xy 0.761 -0.269) (xy 0.763 -0.267) (xy 0.765 -0.265) (xy 0.767 -0.263) + (xy 0.769 -0.261) (xy 0.771 -0.26) (xy 0.773 -0.258) (xy 0.775 -0.257) (xy 0.777 -0.255) (xy 0.78 -0.254) + (xy 0.782 -0.253) (xy 0.785 -0.252) (xy 0.787 -0.252) (xy 0.79 -0.251) (xy 0.792 -0.251) (xy 0.795 -0.25) + (xy 0.797 -0.25) (xy 0.8 -0.25) (xy 1.3 -0.25) (xy 1.303 -0.25) (xy 1.305 -0.25) (xy 1.308 -0.251) + (xy 1.31 -0.251) (xy 1.313 -0.252) (xy 1.315 -0.252) (xy 1.318 -0.253) (xy 1.32 -0.254) (xy 1.323 -0.255) + (xy 1.325 -0.257) (xy 1.327 -0.258) (xy 1.329 -0.26) (xy 1.331 -0.261) (xy 1.333 -0.263) (xy 1.335 -0.265) + (xy 1.337 -0.267) (xy 1.339 -0.269) (xy 1.34 -0.271) (xy 1.342 -0.273) (xy 1.343 -0.275) (xy 1.345 -0.277) + (xy 1.346 -0.28) (xy 1.347 -0.282) (xy 1.348 -0.285) (xy 1.348 -0.287) (xy 1.349 -0.29) (xy 1.349 -0.292) + (xy 1.35 -0.295) (xy 1.35 -0.297) (xy 1.35 -0.3) (xy 1.35 -0.5) (xy 1.35 -0.503) (xy 1.35 -0.505) + (xy 1.349 -0.508) (xy 1.349 -0.51) (xy 1.348 -0.513) (xy 1.348 -0.515) (xy 1.347 -0.518) (xy 1.346 -0.52) + (xy 1.345 -0.523) (xy 1.343 -0.525) (xy 1.342 -0.527) (xy 1.34 -0.529) (xy 1.339 -0.531) (xy 1.337 -0.533) + (xy 1.335 -0.535) (xy 1.333 -0.537) (xy 1.331 -0.539) (xy 1.329 -0.54) (xy 1.327 -0.542) (xy 1.325 -0.543) + (xy 1.323 -0.545) (xy 1.32 -0.546) (xy 1.318 -0.547) (xy 1.315 -0.548) (xy 1.313 -0.548) (xy 1.31 -0.549) + (xy 1.308 -0.549) (xy 1.305 -0.55) (xy 1.303 -0.55) (xy 1.3 -0.55) (xy 0.8 -0.55) (xy 0.797 -0.55) + (xy 0.795 -0.55) (xy 0.792 -0.549) (xy 0.79 -0.549) (xy 0.787 -0.548) (xy 0.785 -0.548) (xy 0.782 -0.547) + (xy 0.78 -0.546) (xy 0.777 -0.545) (xy 0.775 -0.543) (xy 0.773 -0.542) (xy 0.771 -0.54) (xy 0.769 -0.539) + (xy 0.767 -0.537) (xy 0.765 -0.535) (xy 0.763 -0.533) (xy 0.761 -0.531) (xy 0.76 -0.529) (xy 0.758 -0.527) + (xy 0.757 -0.525) (xy 0.755 -0.523) (xy 0.754 -0.52) (xy 0.753 -0.518) (xy 0.752 -0.515) (xy 0.752 -0.513) + (xy 0.751 -0.51) (xy 0.751 -0.508) (xy 0.75 -0.505) (xy 0.75 -0.503) (xy 0.75 -0.5) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "25ee01e6-ff77-485f-afd8-373dc7111d4b") + ) + (fp_poly + (pts + (xy 0.75 -0.9) (xy 0.75 -0.7) (xy 0.75 -0.697) (xy 0.75 -0.695) (xy 0.751 -0.692) (xy 0.751 -0.69) + (xy 0.752 -0.687) (xy 0.752 -0.685) (xy 0.753 -0.682) (xy 0.754 -0.68) (xy 0.755 -0.677) (xy 0.757 -0.675) + (xy 0.758 -0.673) (xy 0.76 -0.671) (xy 0.761 -0.669) (xy 0.763 -0.667) (xy 0.765 -0.665) (xy 0.767 -0.663) + (xy 0.769 -0.661) (xy 0.771 -0.66) (xy 0.773 -0.658) (xy 0.775 -0.657) (xy 0.777 -0.655) (xy 0.78 -0.654) + (xy 0.782 -0.653) (xy 0.785 -0.652) (xy 0.787 -0.652) (xy 0.79 -0.651) (xy 0.792 -0.651) (xy 0.795 -0.65) + (xy 0.797 -0.65) (xy 0.8 -0.65) (xy 1.3 -0.65) (xy 1.303 -0.65) (xy 1.305 -0.65) (xy 1.308 -0.651) + (xy 1.31 -0.651) (xy 1.313 -0.652) (xy 1.315 -0.652) (xy 1.318 -0.653) (xy 1.32 -0.654) (xy 1.323 -0.655) + (xy 1.325 -0.657) (xy 1.327 -0.658) (xy 1.329 -0.66) (xy 1.331 -0.661) (xy 1.333 -0.663) (xy 1.335 -0.665) + (xy 1.337 -0.667) (xy 1.339 -0.669) (xy 1.34 -0.671) (xy 1.342 -0.673) (xy 1.343 -0.675) (xy 1.345 -0.677) + (xy 1.346 -0.68) (xy 1.347 -0.682) (xy 1.348 -0.685) (xy 1.348 -0.687) (xy 1.349 -0.69) (xy 1.349 -0.692) + (xy 1.35 -0.695) (xy 1.35 -0.697) (xy 1.35 -0.7) (xy 1.35 -0.9) (xy 1.35 -0.903) (xy 1.35 -0.905) + (xy 1.349 -0.908) (xy 1.349 -0.91) (xy 1.348 -0.913) (xy 1.348 -0.915) (xy 1.347 -0.918) (xy 1.346 -0.92) + (xy 1.345 -0.923) (xy 1.343 -0.925) (xy 1.342 -0.927) (xy 1.34 -0.929) (xy 1.339 -0.931) (xy 1.337 -0.933) + (xy 1.335 -0.935) (xy 1.333 -0.937) (xy 1.331 -0.939) (xy 1.329 -0.94) (xy 1.327 -0.942) (xy 1.325 -0.943) + (xy 1.323 -0.945) (xy 1.32 -0.946) (xy 1.318 -0.947) (xy 1.315 -0.948) (xy 1.313 -0.948) (xy 1.31 -0.949) + (xy 1.308 -0.949) (xy 1.305 -0.95) (xy 1.303 -0.95) (xy 1.3 -0.95) (xy 0.8 -0.95) (xy 0.797 -0.95) + (xy 0.795 -0.95) (xy 0.792 -0.949) (xy 0.79 -0.949) (xy 0.787 -0.948) (xy 0.785 -0.948) (xy 0.782 -0.947) + (xy 0.78 -0.946) (xy 0.777 -0.945) (xy 0.775 -0.943) (xy 0.773 -0.942) (xy 0.771 -0.94) (xy 0.769 -0.939) + (xy 0.767 -0.937) (xy 0.765 -0.935) (xy 0.763 -0.933) (xy 0.761 -0.931) (xy 0.76 -0.929) (xy 0.758 -0.927) + (xy 0.757 -0.925) (xy 0.755 -0.923) (xy 0.754 -0.92) (xy 0.753 -0.918) (xy 0.752 -0.915) (xy 0.752 -0.913) + (xy 0.751 -0.91) (xy 0.751 -0.908) (xy 0.75 -0.905) (xy 0.75 -0.903) (xy 0.75 -0.9) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "3a99eb35-edff-45d8-a202-17ec38d8b407") + ) + (fp_poly + (pts + (xy -0.5 -0.7) (xy -0.5 0.7) (xy -0.5 0.705) (xy -0.499 0.71) (xy -0.499 0.716) (xy -0.498 0.721) + (xy -0.497 0.726) (xy -0.495 0.731) (xy -0.493 0.736) (xy -0.491 0.741) (xy -0.489 0.745) (xy -0.487 0.75) + (xy -0.484 0.754) (xy -0.481 0.759) (xy -0.478 0.763) (xy -0.474 0.767) (xy -0.471 0.771) (xy -0.467 0.774) + (xy -0.463 0.778) (xy -0.459 0.781) (xy -0.454 0.784) (xy -0.45 0.787) (xy -0.445 0.789) (xy -0.441 0.791) + (xy -0.436 0.793) (xy -0.431 0.795) (xy -0.426 0.797) (xy -0.421 0.798) (xy -0.416 0.799) (xy -0.41 0.799) + (xy -0.405 0.8) (xy -0.4 0.8) (xy 0.4 0.8) (xy 0.405 0.8) (xy 0.41 0.799) (xy 0.416 0.799) (xy 0.421 0.798) + (xy 0.426 0.797) (xy 0.431 0.795) (xy 0.436 0.793) (xy 0.441 0.791) (xy 0.445 0.789) (xy 0.45 0.787) + (xy 0.454 0.784) (xy 0.459 0.781) (xy 0.463 0.778) (xy 0.467 0.774) (xy 0.471 0.771) (xy 0.474 0.767) + (xy 0.478 0.763) (xy 0.481 0.759) (xy 0.484 0.754) (xy 0.487 0.75) (xy 0.489 0.745) (xy 0.491 0.741) + (xy 0.493 0.736) (xy 0.495 0.731) (xy 0.497 0.726) (xy 0.498 0.721) (xy 0.499 0.716) (xy 0.499 0.71) + (xy 0.5 0.705) (xy 0.5 0.7) (xy 0.5 -0.7) (xy 0.5 -0.705) (xy 0.499 -0.71) (xy 0.499 -0.716) (xy 0.498 -0.721) + (xy 0.497 -0.726) (xy 0.495 -0.731) (xy 0.493 -0.736) (xy 0.491 -0.741) (xy 0.489 -0.745) (xy 0.487 -0.75) + (xy 0.484 -0.754) (xy 0.481 -0.759) (xy 0.478 -0.763) (xy 0.474 -0.767) (xy 0.471 -0.771) (xy 0.467 -0.774) + (xy 0.463 -0.778) (xy 0.459 -0.781) (xy 0.454 -0.784) (xy 0.45 -0.787) (xy 0.445 -0.789) (xy 0.441 -0.791) + (xy 0.436 -0.793) (xy 0.431 -0.795) (xy 0.426 -0.797) (xy 0.421 -0.798) (xy 0.416 -0.799) (xy 0.41 -0.799) + (xy 0.405 -0.8) (xy 0.4 -0.8) (xy -0.4 -0.8) (xy -0.405 -0.8) (xy -0.41 -0.799) (xy -0.416 -0.799) + (xy -0.421 -0.798) (xy -0.426 -0.797) (xy -0.431 -0.795) (xy -0.436 -0.793) (xy -0.441 -0.791) (xy -0.445 -0.789) + (xy -0.45 -0.787) (xy -0.454 -0.784) (xy -0.459 -0.781) (xy -0.463 -0.778) (xy -0.467 -0.774) (xy -0.471 -0.771) + (xy -0.474 -0.767) (xy -0.478 -0.763) (xy -0.481 -0.759) (xy -0.484 -0.754) (xy -0.487 -0.75) (xy -0.489 -0.745) + (xy -0.491 -0.741) (xy -0.493 -0.736) (xy -0.495 -0.731) (xy -0.497 -0.726) (xy -0.498 -0.721) (xy -0.499 -0.716) + (xy -0.499 -0.71) (xy -0.5 -0.705) (xy -0.5 -0.7) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "b3c1629f-8214-474e-ab33-9ceabfec1aa7") + ) + (fp_poly + (pts + (xy -1.35 0.7) (xy -1.35 0.9) (xy -1.35 0.903) (xy -1.35 0.905) (xy -1.349 0.908) (xy -1.349 0.91) + (xy -1.348 0.913) (xy -1.348 0.915) (xy -1.347 0.918) (xy -1.346 0.92) (xy -1.345 0.923) (xy -1.343 0.925) + (xy -1.342 0.927) (xy -1.34 0.929) (xy -1.339 0.931) (xy -1.337 0.933) (xy -1.335 0.935) (xy -1.333 0.937) + (xy -1.331 0.939) (xy -1.329 0.94) (xy -1.327 0.942) (xy -1.325 0.943) (xy -1.323 0.945) (xy -1.32 0.946) + (xy -1.318 0.947) (xy -1.315 0.948) (xy -1.313 0.948) (xy -1.31 0.949) (xy -1.308 0.949) (xy -1.305 0.95) + (xy -1.303 0.95) (xy -1.3 0.95) (xy -0.8 0.95) (xy -0.797 0.95) (xy -0.795 0.95) (xy -0.792 0.949) + (xy -0.79 0.949) (xy -0.787 0.948) (xy -0.785 0.948) (xy -0.782 0.947) (xy -0.78 0.946) (xy -0.777 0.945) + (xy -0.775 0.943) (xy -0.773 0.942) (xy -0.771 0.94) (xy -0.769 0.939) (xy -0.767 0.937) (xy -0.765 0.935) + (xy -0.763 0.933) (xy -0.761 0.931) (xy -0.76 0.929) (xy -0.758 0.927) (xy -0.757 0.925) (xy -0.755 0.923) + (xy -0.754 0.92) (xy -0.753 0.918) (xy -0.752 0.915) (xy -0.752 0.913) (xy -0.751 0.91) (xy -0.751 0.908) + (xy -0.75 0.905) (xy -0.75 0.903) (xy -0.75 0.9) (xy -0.75 0.7) (xy -0.75 0.697) (xy -0.75 0.695) + (xy -0.751 0.692) (xy -0.751 0.69) (xy -0.752 0.687) (xy -0.752 0.685) (xy -0.753 0.682) (xy -0.754 0.68) + (xy -0.755 0.677) (xy -0.757 0.675) (xy -0.758 0.673) (xy -0.76 0.671) (xy -0.761 0.669) (xy -0.763 0.667) + (xy -0.765 0.665) (xy -0.767 0.663) (xy -0.769 0.661) (xy -0.771 0.66) (xy -0.773 0.658) (xy -0.775 0.657) + (xy -0.777 0.655) (xy -0.78 0.654) (xy -0.782 0.653) (xy -0.785 0.652) (xy -0.787 0.652) (xy -0.79 0.651) + (xy -0.792 0.651) (xy -0.795 0.65) (xy -0.797 0.65) (xy -0.8 0.65) (xy -1.3 0.65) (xy -1.303 0.65) + (xy -1.305 0.65) (xy -1.308 0.651) (xy -1.31 0.651) (xy -1.313 0.652) (xy -1.315 0.652) (xy -1.318 0.653) + (xy -1.32 0.654) (xy -1.323 0.655) (xy -1.325 0.657) (xy -1.327 0.658) (xy -1.329 0.66) (xy -1.331 0.661) + (xy -1.333 0.663) (xy -1.335 0.665) (xy -1.337 0.667) (xy -1.339 0.669) (xy -1.34 0.671) (xy -1.342 0.673) + (xy -1.343 0.675) (xy -1.345 0.677) (xy -1.346 0.68) (xy -1.347 0.682) (xy -1.348 0.685) (xy -1.348 0.687) + (xy -1.349 0.69) (xy -1.349 0.692) (xy -1.35 0.695) (xy -1.35 0.697) (xy -1.35 0.7) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "8c38b70d-879c-4b02-b859-60efa28f9653") + ) + (fp_poly + (pts + (xy -1.35 0.3) (xy -1.35 0.5) (xy -1.35 0.503) (xy -1.35 0.505) (xy -1.349 0.508) (xy -1.349 0.51) + (xy -1.348 0.513) (xy -1.348 0.515) (xy -1.347 0.518) (xy -1.346 0.52) (xy -1.345 0.523) (xy -1.343 0.525) + (xy -1.342 0.527) (xy -1.34 0.529) (xy -1.339 0.531) (xy -1.337 0.533) (xy -1.335 0.535) (xy -1.333 0.537) + (xy -1.331 0.539) (xy -1.329 0.54) (xy -1.327 0.542) (xy -1.325 0.543) (xy -1.323 0.545) (xy -1.32 0.546) + (xy -1.318 0.547) (xy -1.315 0.548) (xy -1.313 0.548) (xy -1.31 0.549) (xy -1.308 0.549) (xy -1.305 0.55) + (xy -1.303 0.55) (xy -1.3 0.55) (xy -0.8 0.55) (xy -0.797 0.55) (xy -0.795 0.55) (xy -0.792 0.549) + (xy -0.79 0.549) (xy -0.787 0.548) (xy -0.785 0.548) (xy -0.782 0.547) (xy -0.78 0.546) (xy -0.777 0.545) + (xy -0.775 0.543) (xy -0.773 0.542) (xy -0.771 0.54) (xy -0.769 0.539) (xy -0.767 0.537) (xy -0.765 0.535) + (xy -0.763 0.533) (xy -0.761 0.531) (xy -0.76 0.529) (xy -0.758 0.527) (xy -0.757 0.525) (xy -0.755 0.523) + (xy -0.754 0.52) (xy -0.753 0.518) (xy -0.752 0.515) (xy -0.752 0.513) (xy -0.751 0.51) (xy -0.751 0.508) + (xy -0.75 0.505) (xy -0.75 0.503) (xy -0.75 0.5) (xy -0.75 0.3) (xy -0.75 0.297) (xy -0.75 0.295) + (xy -0.751 0.292) (xy -0.751 0.29) (xy -0.752 0.287) (xy -0.752 0.285) (xy -0.753 0.282) (xy -0.754 0.28) + (xy -0.755 0.277) (xy -0.757 0.275) (xy -0.758 0.273) (xy -0.76 0.271) (xy -0.761 0.269) (xy -0.763 0.267) + (xy -0.765 0.265) (xy -0.767 0.263) (xy -0.769 0.261) (xy -0.771 0.26) (xy -0.773 0.258) (xy -0.775 0.257) + (xy -0.777 0.255) (xy -0.78 0.254) (xy -0.782 0.253) (xy -0.785 0.252) (xy -0.787 0.252) (xy -0.79 0.251) + (xy -0.792 0.251) (xy -0.795 0.25) (xy -0.797 0.25) (xy -0.8 0.25) (xy -1.3 0.25) (xy -1.303 0.25) + (xy -1.305 0.25) (xy -1.308 0.251) (xy -1.31 0.251) (xy -1.313 0.252) (xy -1.315 0.252) (xy -1.318 0.253) + (xy -1.32 0.254) (xy -1.323 0.255) (xy -1.325 0.257) (xy -1.327 0.258) (xy -1.329 0.26) (xy -1.331 0.261) + (xy -1.333 0.263) (xy -1.335 0.265) (xy -1.337 0.267) (xy -1.339 0.269) (xy -1.34 0.271) (xy -1.342 0.273) + (xy -1.343 0.275) (xy -1.345 0.277) (xy -1.346 0.28) (xy -1.347 0.282) (xy -1.348 0.285) (xy -1.348 0.287) + (xy -1.349 0.29) (xy -1.349 0.292) (xy -1.35 0.295) (xy -1.35 0.297) (xy -1.35 0.3) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "492cd4e8-411d-4ee3-8e92-40abeadc6364") + ) + (fp_poly + (pts + (xy -1.35 -0.1) (xy -1.35 0.1) (xy -1.35 0.103) (xy -1.35 0.105) (xy -1.349 0.108) (xy -1.349 0.11) + (xy -1.348 0.113) (xy -1.348 0.115) (xy -1.347 0.118) (xy -1.346 0.12) (xy -1.345 0.123) (xy -1.343 0.125) + (xy -1.342 0.127) (xy -1.34 0.129) (xy -1.339 0.131) (xy -1.337 0.133) (xy -1.335 0.135) (xy -1.333 0.137) + (xy -1.331 0.139) (xy -1.329 0.14) (xy -1.327 0.142) (xy -1.325 0.143) (xy -1.323 0.145) (xy -1.32 0.146) + (xy -1.318 0.147) (xy -1.315 0.148) (xy -1.313 0.148) (xy -1.31 0.149) (xy -1.308 0.149) (xy -1.305 0.15) + (xy -1.303 0.15) (xy -1.3 0.15) (xy -0.8 0.15) (xy -0.797 0.15) (xy -0.795 0.15) (xy -0.792 0.149) + (xy -0.79 0.149) (xy -0.787 0.148) (xy -0.785 0.148) (xy -0.782 0.147) (xy -0.78 0.146) (xy -0.777 0.145) + (xy -0.775 0.143) (xy -0.773 0.142) (xy -0.771 0.14) (xy -0.769 0.139) (xy -0.767 0.137) (xy -0.765 0.135) + (xy -0.763 0.133) (xy -0.761 0.131) (xy -0.76 0.129) (xy -0.758 0.127) (xy -0.757 0.125) (xy -0.755 0.123) + (xy -0.754 0.12) (xy -0.753 0.118) (xy -0.752 0.115) (xy -0.752 0.113) (xy -0.751 0.11) (xy -0.751 0.108) + (xy -0.75 0.105) (xy -0.75 0.103) (xy -0.75 0.1) (xy -0.75 -0.1) (xy -0.75 -0.103) (xy -0.75 -0.105) + (xy -0.751 -0.108) (xy -0.751 -0.11) (xy -0.752 -0.113) (xy -0.752 -0.115) (xy -0.753 -0.118) (xy -0.754 -0.12) + (xy -0.755 -0.123) (xy -0.757 -0.125) (xy -0.758 -0.127) (xy -0.76 -0.129) (xy -0.761 -0.131) (xy -0.763 -0.133) + (xy -0.765 -0.135) (xy -0.767 -0.137) (xy -0.769 -0.139) (xy -0.771 -0.14) (xy -0.773 -0.142) (xy -0.775 -0.143) + (xy -0.777 -0.145) (xy -0.78 -0.146) (xy -0.782 -0.147) (xy -0.785 -0.148) (xy -0.787 -0.148) (xy -0.79 -0.149) + (xy -0.792 -0.149) (xy -0.795 -0.15) (xy -0.797 -0.15) (xy -0.8 -0.15) (xy -1.3 -0.15) (xy -1.303 -0.15) + (xy -1.305 -0.15) (xy -1.308 -0.149) (xy -1.31 -0.149) (xy -1.313 -0.148) (xy -1.315 -0.148) (xy -1.318 -0.147) + (xy -1.32 -0.146) (xy -1.323 -0.145) (xy -1.325 -0.143) (xy -1.327 -0.142) (xy -1.329 -0.14) (xy -1.331 -0.139) + (xy -1.333 -0.137) (xy -1.335 -0.135) (xy -1.337 -0.133) (xy -1.339 -0.131) (xy -1.34 -0.129) (xy -1.342 -0.127) + (xy -1.343 -0.125) (xy -1.345 -0.123) (xy -1.346 -0.12) (xy -1.347 -0.118) (xy -1.348 -0.115) (xy -1.348 -0.113) + (xy -1.349 -0.11) (xy -1.349 -0.108) (xy -1.35 -0.105) (xy -1.35 -0.103) (xy -1.35 -0.1) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "8b59ab75-fa70-4411-867f-781f5aebd7f8") + ) + (fp_poly + (pts + (xy -1.35 -0.5) (xy -1.35 -0.3) (xy -1.35 -0.297) (xy -1.35 -0.295) (xy -1.349 -0.292) (xy -1.349 -0.29) + (xy -1.348 -0.287) (xy -1.348 -0.285) (xy -1.347 -0.282) (xy -1.346 -0.28) (xy -1.345 -0.277) (xy -1.343 -0.275) + (xy -1.342 -0.273) (xy -1.34 -0.271) (xy -1.339 -0.269) (xy -1.337 -0.267) (xy -1.335 -0.265) (xy -1.333 -0.263) + (xy -1.331 -0.261) (xy -1.329 -0.26) (xy -1.327 -0.258) (xy -1.325 -0.257) (xy -1.323 -0.255) (xy -1.32 -0.254) + (xy -1.318 -0.253) (xy -1.315 -0.252) (xy -1.313 -0.252) (xy -1.31 -0.251) (xy -1.308 -0.251) (xy -1.305 -0.25) + (xy -1.303 -0.25) (xy -1.3 -0.25) (xy -0.8 -0.25) (xy -0.797 -0.25) (xy -0.795 -0.25) (xy -0.792 -0.251) + (xy -0.79 -0.251) (xy -0.787 -0.252) (xy -0.785 -0.252) (xy -0.782 -0.253) (xy -0.78 -0.254) (xy -0.777 -0.255) + (xy -0.775 -0.257) (xy -0.773 -0.258) (xy -0.771 -0.26) (xy -0.769 -0.261) (xy -0.767 -0.263) (xy -0.765 -0.265) + (xy -0.763 -0.267) (xy -0.761 -0.269) (xy -0.76 -0.271) (xy -0.758 -0.273) (xy -0.757 -0.275) (xy -0.755 -0.277) + (xy -0.754 -0.28) (xy -0.753 -0.282) (xy -0.752 -0.285) (xy -0.752 -0.287) (xy -0.751 -0.29) (xy -0.751 -0.292) + (xy -0.75 -0.295) (xy -0.75 -0.297) (xy -0.75 -0.3) (xy -0.75 -0.5) (xy -0.75 -0.503) (xy -0.75 -0.505) + (xy -0.751 -0.508) (xy -0.751 -0.51) (xy -0.752 -0.513) (xy -0.752 -0.515) (xy -0.753 -0.518) (xy -0.754 -0.52) + (xy -0.755 -0.523) (xy -0.757 -0.525) (xy -0.758 -0.527) (xy -0.76 -0.529) (xy -0.761 -0.531) (xy -0.763 -0.533) + (xy -0.765 -0.535) (xy -0.767 -0.537) (xy -0.769 -0.539) (xy -0.771 -0.54) (xy -0.773 -0.542) (xy -0.775 -0.543) + (xy -0.777 -0.545) (xy -0.78 -0.546) (xy -0.782 -0.547) (xy -0.785 -0.548) (xy -0.787 -0.548) (xy -0.79 -0.549) + (xy -0.792 -0.549) (xy -0.795 -0.55) (xy -0.797 -0.55) (xy -0.8 -0.55) (xy -1.3 -0.55) (xy -1.303 -0.55) + (xy -1.305 -0.55) (xy -1.308 -0.549) (xy -1.31 -0.549) (xy -1.313 -0.548) (xy -1.315 -0.548) (xy -1.318 -0.547) + (xy -1.32 -0.546) (xy -1.323 -0.545) (xy -1.325 -0.543) (xy -1.327 -0.542) (xy -1.329 -0.54) (xy -1.331 -0.539) + (xy -1.333 -0.537) (xy -1.335 -0.535) (xy -1.337 -0.533) (xy -1.339 -0.531) (xy -1.34 -0.529) (xy -1.342 -0.527) + (xy -1.343 -0.525) (xy -1.345 -0.523) (xy -1.346 -0.52) (xy -1.347 -0.518) (xy -1.348 -0.515) (xy -1.348 -0.513) + (xy -1.349 -0.51) (xy -1.349 -0.508) (xy -1.35 -0.505) (xy -1.35 -0.503) (xy -1.35 -0.5) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "dc0c89bb-44ae-42b0-bda4-e4340db9a047") + ) + (fp_poly + (pts + (xy -1.35 -0.9) (xy -1.35 -0.7) (xy -1.35 -0.697) (xy -1.35 -0.695) (xy -1.349 -0.692) (xy -1.349 -0.69) + (xy -1.348 -0.687) (xy -1.348 -0.685) (xy -1.347 -0.682) (xy -1.346 -0.68) (xy -1.345 -0.677) (xy -1.343 -0.675) + (xy -1.342 -0.673) (xy -1.34 -0.671) (xy -1.339 -0.669) (xy -1.337 -0.667) (xy -1.335 -0.665) (xy -1.333 -0.663) + (xy -1.331 -0.661) (xy -1.329 -0.66) (xy -1.327 -0.658) (xy -1.325 -0.657) (xy -1.323 -0.655) (xy -1.32 -0.654) + (xy -1.318 -0.653) (xy -1.315 -0.652) (xy -1.313 -0.652) (xy -1.31 -0.651) (xy -1.308 -0.651) (xy -1.305 -0.65) + (xy -1.303 -0.65) (xy -1.3 -0.65) (xy -0.8 -0.65) (xy -0.797 -0.65) (xy -0.795 -0.65) (xy -0.792 -0.651) + (xy -0.79 -0.651) (xy -0.787 -0.652) (xy -0.785 -0.652) (xy -0.782 -0.653) (xy -0.78 -0.654) (xy -0.777 -0.655) + (xy -0.775 -0.657) (xy -0.773 -0.658) (xy -0.771 -0.66) (xy -0.769 -0.661) (xy -0.767 -0.663) (xy -0.765 -0.665) + (xy -0.763 -0.667) (xy -0.761 -0.669) (xy -0.76 -0.671) (xy -0.758 -0.673) (xy -0.757 -0.675) (xy -0.755 -0.677) + (xy -0.754 -0.68) (xy -0.753 -0.682) (xy -0.752 -0.685) (xy -0.752 -0.687) (xy -0.751 -0.69) (xy -0.751 -0.692) + (xy -0.75 -0.695) (xy -0.75 -0.697) (xy -0.75 -0.7) (xy -0.75 -0.9) (xy -0.75 -0.903) (xy -0.75 -0.905) + (xy -0.751 -0.908) (xy -0.751 -0.91) (xy -0.752 -0.913) (xy -0.752 -0.915) (xy -0.753 -0.918) (xy -0.754 -0.92) + (xy -0.755 -0.923) (xy -0.757 -0.925) (xy -0.758 -0.927) (xy -0.76 -0.929) (xy -0.761 -0.931) (xy -0.763 -0.933) + (xy -0.765 -0.935) (xy -0.767 -0.937) (xy -0.769 -0.939) (xy -0.771 -0.94) (xy -0.773 -0.942) (xy -0.775 -0.943) + (xy -0.777 -0.945) (xy -0.78 -0.946) (xy -0.782 -0.947) (xy -0.785 -0.948) (xy -0.787 -0.948) (xy -0.79 -0.949) + (xy -0.792 -0.949) (xy -0.795 -0.95) (xy -0.797 -0.95) (xy -0.8 -0.95) (xy -1.3 -0.95) (xy -1.303 -0.95) + (xy -1.305 -0.95) (xy -1.308 -0.949) (xy -1.31 -0.949) (xy -1.313 -0.948) (xy -1.315 -0.948) (xy -1.318 -0.947) + (xy -1.32 -0.946) (xy -1.323 -0.945) (xy -1.325 -0.943) (xy -1.327 -0.942) (xy -1.329 -0.94) (xy -1.331 -0.939) + (xy -1.333 -0.937) (xy -1.335 -0.935) (xy -1.337 -0.933) (xy -1.339 -0.931) (xy -1.34 -0.929) (xy -1.342 -0.927) + (xy -1.343 -0.925) (xy -1.345 -0.923) (xy -1.346 -0.92) (xy -1.347 -0.918) (xy -1.348 -0.915) (xy -1.348 -0.913) + (xy -1.349 -0.91) (xy -1.349 -0.908) (xy -1.35 -0.905) (xy -1.35 -0.903) (xy -1.35 -0.9) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Mask") + (uuid "6b57b875-ad20-4995-9e9e-07c17aab43d2") + ) + (fp_circle + (center -1.95 0.8) + (end -1.85 0.8) + (stroke + (width 0.2) + (type solid) + ) + (fill no) + (layer "B.SilkS") + (uuid "32d8b003-0bb6-4bec-976b-3329bfea2685") + ) + (fp_poly + (pts + (xy -0.425 -0.64) (xy -0.425 0.64) (xy -0.425 0.643) (xy -0.425 0.645) (xy -0.424 0.648) (xy -0.424 0.65) + (xy -0.423 0.653) (xy -0.423 0.655) (xy -0.422 0.658) (xy -0.421 0.66) (xy -0.42 0.663) (xy -0.418 0.665) + (xy -0.417 0.667) (xy -0.415 0.669) (xy -0.414 0.671) (xy -0.412 0.673) (xy -0.41 0.675) (xy -0.408 0.677) + (xy -0.406 0.679) (xy -0.404 0.68) (xy -0.402 0.682) (xy -0.4 0.683) (xy -0.398 0.685) (xy -0.395 0.686) + (xy -0.393 0.687) (xy -0.39 0.688) (xy -0.388 0.688) (xy -0.385 0.689) (xy -0.383 0.689) (xy -0.38 0.69) + (xy -0.378 0.69) (xy -0.375 0.69) (xy 0.375 0.69) (xy 0.378 0.69) (xy 0.38 0.69) (xy 0.383 0.689) + (xy 0.385 0.689) (xy 0.388 0.688) (xy 0.39 0.688) (xy 0.393 0.687) (xy 0.395 0.686) (xy 0.398 0.685) + (xy 0.4 0.683) (xy 0.402 0.682) (xy 0.404 0.68) (xy 0.406 0.679) (xy 0.408 0.677) (xy 0.41 0.675) + (xy 0.412 0.673) (xy 0.414 0.671) (xy 0.415 0.669) (xy 0.417 0.667) (xy 0.418 0.665) (xy 0.42 0.663) + (xy 0.421 0.66) (xy 0.422 0.658) (xy 0.423 0.655) (xy 0.423 0.653) (xy 0.424 0.65) (xy 0.424 0.648) + (xy 0.425 0.645) (xy 0.425 0.643) (xy 0.425 0.64) (xy 0.425 -0.64) (xy 0.425 -0.643) (xy 0.425 -0.645) + (xy 0.424 -0.648) (xy 0.424 -0.65) (xy 0.423 -0.653) (xy 0.423 -0.655) (xy 0.422 -0.658) (xy 0.421 -0.66) + (xy 0.42 -0.663) (xy 0.418 -0.665) (xy 0.417 -0.667) (xy 0.415 -0.669) (xy 0.414 -0.671) (xy 0.412 -0.673) + (xy 0.41 -0.675) (xy 0.408 -0.677) (xy 0.406 -0.679) (xy 0.404 -0.68) (xy 0.402 -0.682) (xy 0.4 -0.683) + (xy 0.398 -0.685) (xy 0.395 -0.686) (xy 0.393 -0.687) (xy 0.39 -0.688) (xy 0.388 -0.688) (xy 0.385 -0.689) + (xy 0.383 -0.689) (xy 0.38 -0.69) (xy 0.378 -0.69) (xy 0.375 -0.69) (xy -0.375 -0.69) (xy -0.378 -0.69) + (xy -0.38 -0.69) (xy -0.383 -0.689) (xy -0.385 -0.689) (xy -0.388 -0.688) (xy -0.39 -0.688) (xy -0.393 -0.687) + (xy -0.395 -0.686) (xy -0.398 -0.685) (xy -0.4 -0.683) (xy -0.402 -0.682) (xy -0.404 -0.68) (xy -0.406 -0.679) + (xy -0.408 -0.677) (xy -0.41 -0.675) (xy -0.412 -0.673) (xy -0.414 -0.671) (xy -0.415 -0.669) (xy -0.417 -0.667) + (xy -0.418 -0.665) (xy -0.42 -0.663) (xy -0.421 -0.66) (xy -0.422 -0.658) (xy -0.423 -0.655) (xy -0.423 -0.653) + (xy -0.424 -0.65) (xy -0.424 -0.648) (xy -0.425 -0.645) (xy -0.425 -0.643) (xy -0.425 -0.64) + ) + (stroke + (width 0.01) + (type solid) + ) + (fill yes) + (layer "B.Paste") + (uuid "c5e6763e-4462-4a71-a535-3e33db48aadb") + ) + (fp_line + (start 1.55 1.25) + (end -1.55 1.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "cac4d44d-f864-4ec4-b7b3-2f2b6a13ef17") + ) + (fp_line + (start 1.55 -1.25) + (end 1.55 1.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "6669dc51-3647-4c1f-a440-174ad91e28fe") + ) + (fp_line + (start -1.55 1.25) + (end -1.55 -1.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "b76e27f0-a148-4c4b-af8d-a2f3968589fb") + ) + (fp_line + (start -1.55 -1.25) + (end 1.55 -1.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "09a7127a-325e-4eb3-84df-0a0fdb36fc39") + ) + (fp_line + (start 1.1 1) + (end 1.1 -1) + (stroke + (width 0.127) + (type solid) + ) + (layer "B.Fab") + (uuid "56b98458-a4fa-48e7-8521-42426e36a0e9") + ) + (fp_line + (start 1.1 -1) + (end -1.1 -1) + (stroke + (width 0.127) + (type solid) + ) + (layer "B.Fab") + (uuid "d94bbe63-5806-4b23-95f9-71c4d4303cb5") + ) + (fp_line + (start -1.1 1) + (end 1.1 1) + (stroke + (width 0.127) + (type solid) + ) + (layer "B.Fab") + (uuid "67b4f308-c3f2-4ef4-a86d-20b9cdd22876") + ) + (fp_line + (start -1.1 -1) + (end -1.1 1) + (stroke + (width 0.127) + (type solid) ) + (layer "B.Fab") + (uuid "bc635484-2fa6-4a12-af71-410867095caf") + ) + (fp_circle + (center -1.95 0.8) + (end -1.85 0.8) + (stroke + (width 0.2) + (type solid) + ) + (fill no) + (layer "B.Fab") + (uuid "256e5e24-7029-4479-a578-9de2f6c1283b") + ) + (pad "1" smd roundrect + (at -1.05 0.8 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "VSYS") + (pinfunction "SYS_1") + (pintype "output") + (uuid "b69ba64e-8bf7-4b6e-9baa-7ad824e1d524") + ) + (pad "2" smd roundrect + (at -1.05 0.4 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "VBAT") + (pinfunction "BAT_2") + (pintype "output") + (uuid "85ad80bf-1981-4f7b-b4bc-586035c9da0a") + ) + (pad "3" smd roundrect + (at -1.05 0 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "/MCU_Core/STAT2") + (pinfunction "STAT2_3") + (pintype "output") + (uuid "0c7baddb-0a16-4cc0-809e-737780172ae0") + ) + (pad "4" smd roundrect + (at -1.05 -0.4 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "GND") + (pinfunction "~{CE}_4") + (pintype "input") + (uuid "362f73ec-8e08-4edb-b2d5-10d77226bd7a") + ) + (pad "5" smd roundrect + (at -1.05 -0.8 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "GND") + (pinfunction "GND_5") + (pintype "power_in") + (uuid "c86059fb-33ac-4f4f-89c7-fe36b350c269") + ) + (pad "6" smd roundrect + (at 1.05 -0.8 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "/Power_Charger/CHG_TS") + (pinfunction "TS/MR_6") + (pintype "input") + (uuid "2e8a88c8-ed5a-4a85-a885-43baf4f7eeb8") ) - (attr smd) - (duplicate_pad_numbers_are_jumpers no) - (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "ef956fa7-54e3-432e-9c5b-fff3ecba9c23") + (pad "7" smd roundrect + (at 1.05 -0.4 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "/Power_Charger/CHG_VSET") + (pinfunction "ILIM/VSET_7") + (pintype "input") + (uuid "1c14ca36-eeec-4a61-976d-5a082b670417") ) - (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "46b4b9e7-e1ce-4f37-b916-22d5c7bcba2a") + (pad "8" smd roundrect + (at 1.05 0 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "/Power_Charger/CHG_ISET") + (pinfunction "ISET_8") + (pintype "input") + (uuid "12967c0f-f661-4a91-9cc7-27774fa6c9cc") ) - (fp_rect - (start -0.91 0.46) - (end 0.91 -0.46) - (stroke - (width 0.05) - (type solid) - ) - (fill no) - (layer "B.CrtYd") - (uuid "c1a2b563-8c3a-4006-a264-be4229488470") + (pad "9" smd roundrect + (at 1.05 0.4 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "/MCU_Core/STAT1") + (pinfunction "STAT1_9") + (pintype "output") + (uuid "a0ffce4d-3bae-481b-aa81-7cac89e665e0") ) - (fp_rect - (start -0.5 0.25) - (end 0.5 -0.25) - (stroke - (width 0.1) - (type solid) - ) - (fill no) - (layer "B.Fab") - (uuid "af350ab5-cd9f-4748-be68-e8142c8c59e0") + (pad "10" smd roundrect + (at 1.05 0.8 180) + (size 0.5 0.2) + (layers "B.Cu" "B.Paste") + (roundrect_rratio 0.26) + (net "VBUS") + (pinfunction "IN_10") + (pintype "input") + (uuid "65840fb0-9e19-4b51-9ce7-4ed7a0b40a82") ) - (fp_text user "${REFERENCE}" - (at 0 0 0) - (layer "B.Fab") - (uuid "5d0fe1cd-01f2-4009-a25f-685f92784c00") - (effects - (font - (size 0.25 0.25) - (thickness 0.04) + (pad "11" smd custom + (at 0 0 180) + (size 0.5 0.5) + (layers "B.Cu") + (net "GND") + (pinfunction "THERMAL_PAD_11") + (pintype "passive") + (options + (clearance outline) + (anchor rect) + ) + (primitives + (gr_poly + (pts + (xy -0.45 -0.7) (xy -0.45 0.7) (xy -0.45 0.703) (xy -0.45 0.705) (xy -0.449 0.708) (xy -0.449 0.71) + (xy -0.448 0.713) (xy -0.448 0.715) (xy -0.447 0.718) (xy -0.446 0.72) (xy -0.445 0.723) (xy -0.443 0.725) + (xy -0.442 0.727) (xy -0.44 0.729) (xy -0.439 0.731) (xy -0.437 0.733) (xy -0.435 0.735) (xy -0.433 0.737) + (xy -0.431 0.739) (xy -0.429 0.74) (xy -0.427 0.742) (xy -0.425 0.743) (xy -0.423 0.745) (xy -0.42 0.746) + (xy -0.418 0.747) (xy -0.415 0.748) (xy -0.413 0.748) (xy -0.41 0.749) (xy -0.408 0.749) (xy -0.405 0.75) + (xy -0.403 0.75) (xy -0.4 0.75) (xy 0.4 0.75) (xy 0.403 0.75) (xy 0.405 0.75) (xy 0.408 0.749) + (xy 0.41 0.749) (xy 0.413 0.748) (xy 0.415 0.748) (xy 0.418 0.747) (xy 0.42 0.746) (xy 0.423 0.745) + (xy 0.425 0.743) (xy 0.427 0.742) (xy 0.429 0.74) (xy 0.431 0.739) (xy 0.433 0.737) (xy 0.435 0.735) + (xy 0.437 0.733) (xy 0.439 0.731) (xy 0.44 0.729) (xy 0.442 0.727) (xy 0.443 0.725) (xy 0.445 0.723) + (xy 0.446 0.72) (xy 0.447 0.718) (xy 0.448 0.715) (xy 0.448 0.713) (xy 0.449 0.71) (xy 0.449 0.708) + (xy 0.45 0.705) (xy 0.45 0.703) (xy 0.45 0.7) (xy 0.45 -0.7) (xy 0.45 -0.703) (xy 0.45 -0.705) + (xy 0.449 -0.708) (xy 0.449 -0.71) (xy 0.448 -0.713) (xy 0.448 -0.715) (xy 0.447 -0.718) (xy 0.446 -0.72) + (xy 0.445 -0.723) (xy 0.443 -0.725) (xy 0.442 -0.727) (xy 0.44 -0.729) (xy 0.439 -0.731) (xy 0.437 -0.733) + (xy 0.435 -0.735) (xy 0.433 -0.737) (xy 0.431 -0.739) (xy 0.429 -0.74) (xy 0.427 -0.742) (xy 0.425 -0.743) + (xy 0.423 -0.745) (xy 0.42 -0.746) (xy 0.418 -0.747) (xy 0.415 -0.748) (xy 0.413 -0.748) (xy 0.41 -0.749) + (xy 0.408 -0.749) (xy 0.405 -0.75) (xy 0.403 -0.75) (xy 0.4 -0.75) (xy -0.4 -0.75) (xy -0.403 -0.75) + (xy -0.405 -0.75) (xy -0.408 -0.749) (xy -0.41 -0.749) (xy -0.413 -0.748) (xy -0.415 -0.748) (xy -0.418 -0.747) + (xy -0.42 -0.746) (xy -0.423 -0.745) (xy -0.425 -0.743) (xy -0.427 -0.742) (xy -0.429 -0.74) (xy -0.431 -0.739) + (xy -0.433 -0.737) (xy -0.435 -0.735) (xy -0.437 -0.733) (xy -0.439 -0.731) (xy -0.44 -0.729) + (xy -0.442 -0.727) (xy -0.443 -0.725) (xy -0.445 -0.723) (xy -0.446 -0.72) (xy -0.447 -0.718) + (xy -0.448 -0.715) (xy -0.448 -0.713) (xy -0.449 -0.71) (xy -0.449 -0.708) (xy -0.45 -0.705) (xy -0.45 -0.703) + (xy -0.45 -0.7) + ) + (width 0.01) + (fill yes) ) - (justify mirror) ) + (uuid "ff4712ac-a586-4040-9dee-4a8a1f340bb8") ) - (pad "1" smd roundrect - (at -0.48 0 180) - (size 0.56 0.62) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "3V3") - (pintype "passive") - (uuid "c48f2692-bc53-4d5f-ae73-d1fad227714a") + (pad "12" thru_hole circle + (at 0 0.5 180) + (size 0.3 0.3) + (drill 0.2) + (layers "*.Cu") + (remove_unused_layers no) + (net "GND") + (uuid "a70408f9-f447-446f-ab4f-867071df5d38") ) - (pad "2" smd roundrect - (at 0.48 0 180) - (size 0.56 0.62) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) + (pad "13" thru_hole circle + (at 0 -0.5 180) + (size 0.3 0.3) + (drill 0.2) + (layers "*.Cu") + (remove_unused_layers no) (net "GND") - (pintype "passive") - (uuid "5a6c92bf-a917-436c-a490-03ae09ad107c") + (uuid "de4cb4e4-7bab-43fe-ba65-d765b737dbe8") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (model "${KIPRJMOD}/libraries/BQ25185DLHR/BQ25185DLHR.step" (offset (xyz 0 0 0) ) @@ -22489,21 +22412,21 @@ (xyz 1 1 1) ) (rotate - (xyz 0 0 0) + (xyz -90 0 0) ) ) ) - (footprint "Diode_SMD:D_SOD-123" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "962f3015-c784-4c0f-aca3-6fb4c2aa0f15") - (at 135.285 72.44) - (descr "SOD-123") - (tags "SOD-123") - (property "Reference" "D_OR2" - (at 0 2 0) + (uuid "88a25bf2-6956-411c-8c83-7fa8fbc892c3") + (at 133.35 100.05) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_STAT2" + (at 0.09 1.1 180) (layer "B.SilkS") (hide yes) - (uuid "6f72084a-f130-494c-b285-3639f568f7ac") + (uuid "683a2e93-d09d-4016-b8f7-3194e32b4468") (effects (font (size 1 1) @@ -22512,10 +22435,10 @@ (justify mirror) ) ) - (property "Value" "1N4148W" - (at 0 -2.1 0) + (property "Value" "10kΩ" + (at -5.55 0.505 180) (layer "B.Fab") - (uuid "f8ddd6ba-73cb-425f-908a-ca279616d708") + (uuid "b7f23e9f-dfe2-46f3-a858-794f643f6058") (effects (font (size 1 1) @@ -22526,52 +22449,33 @@ ) (property "Datasheet" "" (at 0 0 180) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "13558284-71c3-42d5-8080-40a8ccbb4ccb") + (uuid "43acfff5-ddb7-4ba8-a8af-bd63deab5743") (effects (font (size 1.27 1.27) - (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "Diode, small symbol" + (property "Description" "Resistor" (at 0 0 180) - (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "01f9d385-e089-4dd8-8628-cafd5d09247b") + (uuid "56edb9ad-0fbb-4bb4-be7f-d1247b990d83") (effects (font (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) - ) - ) - (property "Sim.Device" "D" - (at 0 0 0) - (unlocked yes) - (layer "B.Fab") - (hide yes) - (uuid "686f4a21-45e1-4d30-90ca-76ba665040ef") - (effects - (font - (size 1 1) - (thickness 0.15) ) (justify mirror) ) ) - (property "Sim.Pins" "1=K 2=A" - (at 0 0 0) - (unlocked yes) - (layer "B.Fab") + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 180) + (layer "B.SilkS") (hide yes) - (uuid "fa93df4f-0a8e-4831-b07e-8c982f8a448d") + (uuid "83734f2d-5939-47b5-ae35-0f90ee64eadf") (effects (font (size 1 1) @@ -22580,12 +22484,12 @@ (justify mirror) ) ) - (property "MF" "ST(Semtech)" - (at 0 0 0) + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "9ac1cbce-b2da-4221-92ac-fc7dc300208d") + (uuid "918cef0e-119e-4e53-a98c-b9dffc942116") (effects (font (size 1 1) @@ -22594,12 +22498,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "1N4148W" - (at 0 0 0) + (property "Manufacturer_Part_Number" "0402WGF1002TCE" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "4e586f1a-0540-4fb1-b18d-85844fe2f184") + (uuid "adec6d65-8112-4eff-9f83-dbbdeeca13fe") (effects (font (size 1 1) @@ -22608,12 +22512,12 @@ (justify mirror) ) ) - (property "LCSC" "C81598" + (property "LCSC" "C25744" (at 0 0 0) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "d1c3f5fb-5724-4047-9ce9-d1fb036b5348") + (uuid "c2905452-de99-4b1c-afbb-145d4681dd1e") (effects (font (size 1 1) @@ -22622,11 +22526,11 @@ (justify mirror) ) ) - (property "Stackup Path" "D_OR2" - (at -2 0 270) + (property "Stackup Path" "R_STAT2" + (at 0 2 180) (layer "B.SilkS") (hide yes) - (uuid "1591b0bd-7415-4c4d-b8b6-15cc15a43616") + (uuid "2fe23c34-108b-4a40-88df-b2e3ddbab452") (effects (font (size 1.27 1.27) @@ -22634,11 +22538,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:42" - (at -2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:70" + (at 0 2 180) (layer "B.SilkS") (hide yes) - (uuid "127f9262-63f4-4df0-b885-57af9113918f") + (uuid "b6ec057f-dcb3-4f12-9fa4-5da68079988a") (effects (font (size 1.27 1.27) @@ -22646,8 +22550,8 @@ ) ) ) - (property ki_fp_filters "TO-???* *_Diode_* *SingleDiode* D_*") - (path "/ea971f8f-1025-580c-97c7-171cc66c8a28") + (property ki_fp_filters "R_*") + (path "/213051d8-6d7f-5a98-bf06-9f116b171331") (units (unit (name "A") @@ -22657,219 +22561,79 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -2.36 -1) - (end 1.65 -1) - (stroke - (width 0.12) - (type solid) - ) - (layer "B.SilkS") - (uuid "a62a7fd2-a2f9-4c4f-915c-754c27d8f2b5") - ) - (fp_line - (start -2.36 1) - (end -2.36 -1) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "5b3b08aa-de66-4e97-ad5e-168408f525e9") + (uuid "32e17da8-8d64-45cf-9260-e8ea52429479") ) (fp_line - (start -2.36 1) - (end 1.65 1) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "6c3e2c96-959e-49a5-b4bd-981bc0c5988b") - ) - (fp_line - (start -2.35 1.15) - (end -2.35 -1.15) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "04fefd16-9736-4689-98b0-02d0fa379406") - ) - (fp_line - (start -2.35 1.15) - (end 2.35 1.15) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "6c8cd080-4506-4686-9a24-780d50e953a0") - ) - (fp_line - (start 2.35 -1.15) - (end -2.35 -1.15) - (stroke - (width 0.05) - (type solid) - ) - (layer "B.CrtYd") - (uuid "4c7ba51c-72dd-415f-8bdb-2af3f8c493b6") + (uuid "98015d6c-3d6f-4f92-a096-7fbdca2d0cfd") ) - (fp_line - (start 2.35 1.15) - (end 2.35 -1.15) + (fp_rect + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) + (fill no) (layer "B.CrtYd") - (uuid "e7a50f47-c9c4-4c40-839c-09c01cb96c53") - ) - (fp_line - (start -1.4 -0.9) - (end -1.4 0.9) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "c968d15c-0fda-41de-a91a-666ff4472253") - ) - (fp_line - (start -1.4 0.9) - (end 1.4 0.9) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "211f0e24-20de-4026-89da-6fd60d9d8256") - ) - (fp_line - (start -0.75 0) - (end -0.35 0) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "52b780ef-3b77-41e0-933a-ee791c1a45be") - ) - (fp_line - (start -0.35 0) - (end -0.35 -0.55) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "625fbe2f-096f-46ec-96d8-17ccc0b582ba") - ) - (fp_line - (start -0.35 0) - (end -0.35 0.55) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "1625162c-c66d-43c2-8546-45ccb428bb0a") - ) - (fp_line - (start -0.35 0) - (end 0.25 0.4) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "d1d81b97-b330-4d37-b797-4739d8d8b14e") - ) - (fp_line - (start 0.25 -0.4) - (end -0.35 0) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "e2295c20-fe34-4987-893c-e0ea0ca19dfe") - ) - (fp_line - (start 0.25 0) - (end 0.75 0) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "a7ae4b1c-df58-451d-b801-dad81318dcf7") - ) - (fp_line - (start 0.25 0.4) - (end 0.25 -0.4) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "042966ee-d1fe-48bc-ad8f-2eb882f39174") - ) - (fp_line - (start 1.4 -0.9) - (end -1.4 -0.9) - (stroke - (width 0.1) - (type solid) - ) - (layer "B.Fab") - (uuid "05afcd40-b6e8-41bd-a0be-b3bf42356a68") + (uuid "2ef7dfb0-7daa-4d59-9ea5-3abd1b32c039") ) - (fp_line - (start 1.4 0.9) - (end 1.4 -0.9) + (fp_rect + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) + (fill no) (layer "B.Fab") - (uuid "5f1d45e1-2b16-4411-bb38-4e490c9ee0af") + (uuid "fa9d0f2a-149e-4f6e-bfc2-f75b19b7b3fe") ) (fp_text user "${REFERENCE}" - (at 0 2 0) + (at 0 0 180) (layer "B.Fab") - (uuid "d005253a-9a8c-44de-80ac-a3c12bda21a3") + (uuid "01784e9c-53ce-4916-9359-05e7b4f5b157") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.26 0.26) + (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -1.65 0) - (size 0.9 1.2) + (at -0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Control/PWR_LATCH_G") - (pinfunction "K_1") + (net "/MCU_Core/STAT2") (pintype "passive") - (uuid "82277a71-82be-47d6-b287-b6045f431d0d") + (uuid "3f416a4d-b988-404c-81d4-7b3c6afe6571") ) (pad "2" smd roundrect - (at 1.65 0) - (size 0.9 1.2) + (at 0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/PWR_HOLD") - (pinfunction "A_2") + (net "3V3") (pintype "passive") - (uuid "23c9bc63-3793-4295-ab44-99676ca47c98") + (uuid "effa86dc-4cf9-4806-a45c-774a5b47b31e") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Diode_SMD.3dshapes/D_SOD-123.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -22883,15 +22647,15 @@ ) (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "9e33b6f7-03b2-48f7-b4c7-a067ef43611a") - (at 132.285 74.44) + (uuid "89256378-8b06-45a3-9170-cc87240992e0") + (at 141.775 126.065) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_LATCH_G1" - (at 0 1.17 0) + (property "Reference" "R_CC2" + (at 0 1.17 180) (layer "B.SilkS") (hide yes) - (uuid "756ad045-de34-4aa5-8583-720c28e841a7") + (uuid "5c8338be-ebc5-4278-a6be-6e5c0da5c6cf") (effects (font (size 1 1) @@ -22900,10 +22664,10 @@ (justify mirror) ) ) - (property "Value" "1MΩ" - (at 0 -1.17 0) + (property "Value" "5.1kΩ" + (at 0 -1.17 180) (layer "B.Fab") - (uuid "144004f1-efc5-48c5-b085-980750e018e8") + (uuid "8b0626de-cc65-496e-9d52-18a867c5e8db") (effects (font (size 1 1) @@ -22913,10 +22677,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "7a42ab1b-ab89-43be-953f-d26b2c555bba") + (uuid "a6cc48f5-3542-4dc5-8957-db7e9d4dbc1c") (effects (font (size 1.27 1.27) @@ -22925,10 +22689,10 @@ ) ) (property "Description" "Resistor" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "169e50fe-dd62-42f7-99b3-e773cff71e83") + (uuid "2cbc6365-711d-4fca-a71f-ae644fcbc514") (effects (font (size 1.27 1.27) @@ -22937,11 +22701,11 @@ ) ) (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 0) + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "fc5a3232-9451-4f44-894c-50744c0715c5") + (uuid "07cc9a19-3221-4a46-832f-8f542f5f7aa9") (effects (font (size 1 1) @@ -22950,12 +22714,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF1004TCE" - (at 0 0 0) + (property "Manufacturer_Part_Number" "0402WGF5101TCE" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "865ca63a-e1ea-472b-81be-bb28866642bc") + (uuid "ac9fd379-5884-4597-892a-0415c62d9c14") (effects (font (size 1 1) @@ -22964,12 +22728,12 @@ (justify mirror) ) ) - (property "LCSC" "C26083" - (at 0 0 0) + (property "LCSC" "C25905" + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "90ac7081-6eea-4866-a57b-150b0eda4acb") + (uuid "85cfd0e9-01b9-4cf4-8773-c65e2fa66884") (effects (font (size 1 1) @@ -22978,32 +22742,34 @@ (justify mirror) ) ) - (property "Stackup Path" "R_LATCH_G1" - (at -2 0 270) + (property "Stackup Path" "R_CC2" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "37ba0831-6e75-457e-bd89-6155e55bffb1") + (uuid "79251760-58e6-4231-8920-4ae145aea970") (effects (font (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:63" - (at -2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:58" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "f977c22e-19ee-408b-8c39-8abe64ba336f") + (uuid "10132a5e-3328-4bc5-8eac-60ab122be947") (effects (font (size 1.27 1.27) (thickness 0.15) ) + (justify mirror) ) ) (property ki_fp_filters "R_*") - (path "/69e3e4db-a3ee-5e94-9e3d-5b01833af909") + (path "/d76e910c-dbb9-5852-9273-faf8c594840e") (units (unit (name "A") @@ -23020,7 +22786,7 @@ (type solid) ) (layer "B.SilkS") - (uuid "86f8ddc0-59e9-498c-8996-cfe1f4fa18d8") + (uuid "d7f00a62-8534-40c0-b676-c5e7bb881045") ) (fp_line (start -0.153641 0.38) @@ -23030,7 +22796,7 @@ (type solid) ) (layer "B.SilkS") - (uuid "e8813b4d-e697-488b-abd0-9429d007de62") + (uuid "e6bc2a52-3425-462b-ba98-e74edf33eb30") ) (fp_rect (start -0.93 0.47) @@ -23041,7 +22807,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "59f10495-0769-44d6-94f4-e57cfa5318dd") + (uuid "e3112f01-c3cd-4d45-b8a7-20951e7886af") ) (fp_rect (start -0.525 0.27) @@ -23052,12 +22818,12 @@ ) (fill no) (layer "B.Fab") - (uuid "0c0178d2-5757-4f74-b03b-2c576ab49f1b") + (uuid "c458ab8d-80a3-424a-a7ac-33e0a77e6a57") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") - (uuid "c1abb47d-330d-4ec7-829a-66c7979cf1a9") + (uuid "6fd48b24-4255-4a54-a0e7-d1593a174ff5") (effects (font (size 0.26 0.26) @@ -23071,18 +22837,18 @@ (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "GND") + (net "/USB_C/USB_CC2") (pintype "passive") - (uuid "8a4b74b5-ab1f-41d0-b563-b734d4809bf3") + (uuid "ea9bffac-1736-41a8-83aa-a3685ef16deb") ) (pad "2" smd roundrect (at 0.51 0) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Power_Control/PWR_LATCH_G") + (net "GND") (pintype "passive") - (uuid "9d2b1677-ef53-437a-9b45-1474ab7b27a8") + (uuid "696b96b9-731f-45af-8493-d73f061bfe9f") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -23097,17 +22863,29 @@ ) ) ) - (footprint "BT840XE" + (footprint "Diode_SMD:D_SOD-123" (layer "B.Cu") - (uuid "aabe8e27-89df-49df-a86f-275c897c3729") - (at 134.275 106.7) - (descr "Fanstel BT840XE nRF52840 module with SKY66112 PA and u.FL, 15 x 28 x 1.9 mm. Pad positions from the BT840X/BT840XE mechanical drawing, Product Specifications Ver 1.26 p.12 (top view). Pad names are Fanstel's. Origin is the centre of the 15 x 28 mm outline. Fanstel gives no host land pattern here: castellated lands extend 0.5 mm past the module edge and are 0.70 mm wide. Check against the Fanstel library before fab. The upper section is the shield and u.FL, with no pads under it.") - (tags "BT840XE nRF52840 Fanstel Zigbee BLE module") - (property "Reference" "U_MCU1" - (at 0 15 180) + (uuid "962f3015-c784-4c0f-aca3-6fb4c2aa0f15") + (at 135.285 72.44) + (descr "SOD-123") + (tags "SOD-123") + (property "Reference" "D_OR2" + (at 0 2 0) (layer "B.SilkS") (hide yes) - (uuid "2cb1859f-2d3e-413d-b6b8-3d50c815eca1") + (uuid "6f72084a-f130-494c-b285-3639f568f7ac") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Value" "1N4148W" + (at 0 -2.1 0) + (layer "B.Fab") + (uuid "f8ddd6ba-73cb-425f-908a-ca279616d708") (effects (font (size 1 1) @@ -23116,83 +22894,109 @@ (justify mirror) ) ) - (property "Value" "BT840XE" - (at 0 -15 180) + (property "Datasheet" "" + (at 0 0 180) + (unlocked yes) (layer "B.Fab") - (uuid "31f176c7-15f8-4d24-8e61-567aa7b5256a") + (hide yes) + (uuid "13558284-71c3-42d5-8080-40a8ccbb4ccb") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) (justify mirror) ) ) - (property "Datasheet" "" + (property "Description" "Diode, small symbol" (at 0 0 180) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "dc899177-4abd-4ad3-9381-d4344d539229") + (uuid "01f9d385-e089-4dd8-8628-cafd5d09247b") (effects (font (size 1.27 1.27) + (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "" - (at 0 0 180) + (property "Sim.Device" "D" + (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "29506335-09c4-4552-890b-6bb81f7f7e1e") + (uuid "686f4a21-45e1-4d30-90ca-76ba665040ef") (effects (font - (size 1.27 1.27) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "Fanstel" - (at 0 2 0) - (layer "B.SilkS") + (property "Sim.Pins" "1=K 2=A" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "942f232b-d704-46fc-a6a3-c2c786b3a9d8") + (uuid "fa93df4f-0a8e-4831-b07e-8c982f8a448d") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "Manufacturer_Part_Number" "BT840XE" - (at 0 2 0) - (layer "B.SilkS") + (property "MF" "ST(Semtech)" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "d6ebfadf-dc91-4c45-84bf-1cebe7e0d17e") + (uuid "9ac1cbce-b2da-4221-92ac-fc7dc300208d") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "LCSC" "C6132678" - (at 0 2 0) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "1N4148W" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "48e6f464-5adc-419f-ae29-e9fe311f7f70") + (uuid "4e586f1a-0540-4fb1-b18d-85844fe2f184") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) + (justify mirror) ) ) - (property "Stackup Path" "U_MCU1" - (at 0 2 0) + (property "LCSC" "C81598" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "d1c3f5fb-5724-4047-9ce9-d1fb036b5348") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) + ) + (property "Stackup Path" "D_OR2" + (at -2 0 270) (layer "B.SilkS") (hide yes) - (uuid "bf27e28b-e723-4620-9172-491ca747c9e4") + (uuid "1591b0bd-7415-4c4d-b8b6-15cc15a43616") (effects (font (size 1.27 1.27) @@ -23200,11 +23004,11 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:92" - (at 0 2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:44" + (at -2 0 270) (layer "B.SilkS") (hide yes) - (uuid "e45d28c1-9416-458f-9141-cfb15902bf78") + (uuid "127f9262-63f4-4df0-b885-57af9113918f") (effects (font (size 1.27 1.27) @@ -23212,587 +23016,716 @@ ) ) ) - (path "/0466cd2a-b9be-59f2-b3ed-6d30cbef7aef") + (property ki_fp_filters "TO-???* *_Diode_* *SingleDiode* D_*") + (path "/ea971f8f-1025-580c-97c7-171cc66c8a28") + (units + (unit + (name "A") + (pins "1" "2") + ) + ) (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -7.65 -1.15) - (end -6.8 -1.15) + (start -2.36 -1) + (end 1.65 -1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "b97557a3-57b2-4540-8ea8-9319c54a90f0") + (uuid "a62a7fd2-a2f9-4c4f-915c-754c27d8f2b5") ) (fp_line - (start -7.65 14.15) - (end -7.65 -1.15) + (start -2.36 1) + (end -2.36 -1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "75f155a0-4c67-4799-beb9-48b3c6d3eb8e") + (uuid "5b3b08aa-de66-4e97-ad5e-168408f525e9") ) (fp_line - (start -7.5 14.15) - (end 7.65 14.15) + (start -2.36 1) + (end 1.65 1) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "4788ecba-a0c9-4941-9322-ece2a4835804") + (uuid "6c3e2c96-959e-49a5-b4bd-981bc0c5988b") ) (fp_line - (start 7.65 14.15) - (end 7.65 -4) + (start -2.35 1.15) + (end -2.35 -1.15) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "3eb7c903-563b-4977-a693-f954c04bb717") + (layer "B.CrtYd") + (uuid "04fefd16-9736-4689-98b0-02d0fa379406") ) - (fp_circle - (center -7.6 -5.2) - (end -7.45 -5.2) + (fp_line + (start -2.35 1.15) + (end 2.35 1.15) (stroke - (width 0.2) + (width 0.05) (type solid) ) - (fill no) - (layer "B.SilkS") - (uuid "c53b45c3-6d86-4d0e-92e9-8e82405d6bfe") + (layer "B.CrtYd") + (uuid "6c8cd080-4506-4686-9a24-780d50e953a0") ) - (fp_rect - (start -7.75 14.25) - (end 8.25 -14.25) + (fp_line + (start 2.35 -1.15) + (end -2.35 -1.15) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "4c7ba51c-72dd-415f-8bdb-2af3f8c493b6") + ) + (fp_line + (start 2.35 1.15) + (end 2.35 -1.15) (stroke (width 0.05) (type solid) ) - (fill no) (layer "B.CrtYd") - (uuid "f4e3765d-b030-432b-97ed-f7c914532c7c") + (uuid "e7a50f47-c9c4-4c40-839c-09c01cb96c53") ) (fp_line - (start -7.5 -1.3) - (end -7.5 14) + (start -1.4 -0.9) + (end -1.4 0.9) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "7808e0ab-e29c-47ac-9df8-f0a9ba8bee65") + (uuid "c968d15c-0fda-41de-a91a-666ff4472253") ) (fp_line - (start -7.5 14) - (end 7.5 14) + (start -1.4 0.9) + (end 1.4 0.9) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "5a988c9e-b945-48ec-b82b-b4598b45d7de") + (uuid "211f0e24-20de-4026-89da-6fd60d9d8256") ) (fp_line - (start -6.5 -14) - (end -6.5 -1.3) + (start -0.75 0) + (end -0.35 0) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "96585603-a2bd-4fd3-b5e0-617ef3c61b2f") + (uuid "52b780ef-3b77-41e0-933a-ee791c1a45be") ) (fp_line - (start -6.5 -1.3) - (end -7.5 -1.3) + (start -0.35 0) + (end -0.35 -0.55) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "256c16ca-2b16-490c-ab9c-c1c595f6393c") + (uuid "625fbe2f-096f-46ec-96d8-17ccc0b582ba") ) (fp_line - (start 7.5 -14) - (end -6.5 -14) + (start -0.35 0) + (end -0.35 0.55) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "cf249a98-f8e6-4a89-8345-a851573d45fb") + (uuid "1625162c-c66d-43c2-8546-45ccb428bb0a") ) (fp_line - (start 7.5 14) - (end 7.5 -14) + (start -0.35 0) + (end 0.25 0.4) (stroke (width 0.1) (type solid) ) (layer "B.Fab") - (uuid "e443670f-8520-4b94-b0dd-36fbc59f8797") - ) - (pad "1" smd rect - (at -6.375 -5.2) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Accelerometer/I2C_SDA") - (uuid "8916411f-b756-4118-99bb-53c3653422d0") - ) - (pad "2" smd rect - (at -6.375 -6.3) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Accelerometer/I2C_SCL") - (uuid "9a593e04-189b-4cef-a62a-98463b4373bf") - ) - (pad "3" smd rect - (at -6.375 -7.4) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "2677c920-73f4-475e-b6a5-213a176a238d") - ) - (pad "4" smd rect - (at -6.375 -8.5) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "53e6085b-6a94-428e-87f1-8ee57044e6fc") - ) - (pad "5" smd rect - (at -6.375 -9.6) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/STICK_X") - (uuid "88d11f1a-cae0-476c-a6c3-e6f7ff801783") - ) - (pad "6" smd rect - (at -6.375 -10.7) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/STICK_Y") - (uuid "28d70601-c9d3-47ec-8aac-fb28a159df3e") - ) - (pad "7" smd rect - (at -6.375 -11.8) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "8324f349-c7fb-4f86-88a5-d24af7382692") - ) - (pad "8" smd rect - (at -6.375 -12.9) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "927951a5-573f-48e8-bb36-7acc0a33ef1a") - ) - (pad "9" smd rect - (at 7.375 -12.9) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/3V3_RF") - (uuid "ab38fa4f-792c-4acc-8778-c1f844af2c75") - ) - (pad "10" smd rect - (at 7.375 -11.8) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "56ffe25b-8b42-40fb-a8c3-615013d0a782") - ) - (pad "11" smd rect - (at 7.375 -10.7) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "a3c802af-b40a-40b4-85cb-3a7213650dab") - ) - (pad "12" smd rect - (at 7.375 -9.6) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_BOOT") - (uuid "e78f49eb-c825-47e2-8ce9-0b85e8a7559a") - ) - (pad "13" smd rect - (at 7.375 -8.5) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/RGB_DIN") - (uuid "3396466c-76d2-4ac0-b8ea-0126b41126dc") - ) - (pad "14" smd rect - (at 7.375 -7.4) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_RESET") - (uuid "c4760848-9b3a-46a2-9909-348170e3126f") - ) - (pad "15" smd rect - (at 7.375 -6.3) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/SWDCLK") - (uuid "fa50998f-1931-4390-a124-0124e602c61b") - ) - (pad "16" smd rect - (at 7.375 -5.2) - (size 1.25 0.7) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/SWDIO") - (uuid "ceebe878-ea96-45c8-bff8-a90ef3eb97e1") - ) - (pad "A0" smd circle - (at -1.75 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "b4f1248a-2b2a-4325-ae7c-13c178176ccf") - ) - (pad "A1" smd circle - (at -1.75 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "2cce702b-214e-42ca-860b-70865bed1bb3") - ) - (pad "A2" smd circle - (at -1.75 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "295d88e4-8d43-4cc2-9227-927e148f87ce") - ) - (pad "A3" smd circle - (at -1.75 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "10954e29-b362-420b-b3b9-efe105ba521d") - ) - (pad "A4" smd circle - (at -1.75 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/VSYS_SENSE") - (uuid "78470058-2dcd-4fcf-944a-3e21e18fb308") - ) - (pad "A5" smd circle - (at -1.75 -12) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "16c5c162-e989-49fa-965f-35c0b08a1eae") - ) - (pad "A6" smd circle - (at -1.75 -13.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_THR_UP") - (uuid "b4c568fb-6d47-40ef-8cdb-2a78d2db7dc5") - ) - (pad "B0" smd circle - (at -0.25 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "5924291c-f60c-4c9e-b656-b034785d3830") - ) - (pad "B1" smd circle - (at -0.25 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "5fc4f38f-c59a-483a-9709-6fbeb7914146") - ) - (pad "B2" smd circle - (at -0.25 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "5d6964e8-58ce-49b8-b161-e94f441d996a") - ) - (pad "B3" smd circle - (at -0.25 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "5b6bb7d7-41ad-4847-b9d4-eaf8e6d62ad2") - ) - (pad "B4" smd circle - (at -0.25 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "eb928f7c-c6b3-4bbf-b6fb-0cab8d83255e") - ) - (pad "B5" smd circle - (at -0.25 -12) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "d66d7dd7-a4ca-44d9-9abb-e4fa1291e5e6") + (uuid "d1d81b97-b330-4d37-b797-4739d8d8b14e") ) - (pad "B6" smd circle - (at -0.25 -13.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/BTN_STICK") - (uuid "5c808d36-b14d-44a3-85d5-e00e7e74f4d0") + (fp_line + (start 0.25 -0.4) + (end -0.35 0) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "e2295c20-fe34-4987-893c-e0ea0ca19dfe") ) - (pad "C0" smd circle - (at 1.25 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "3f24e259-4519-475d-928d-aaba2b46921a") + (fp_line + (start 0.25 0) + (end 0.75 0) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "a7ae4b1c-df58-451d-b801-dad81318dcf7") ) - (pad "C1" smd circle - (at 1.25 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "290c1b52-f43f-45cb-a342-daca9fdc61c4") + (fp_line + (start 0.25 0.4) + (end 0.25 -0.4) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "042966ee-d1fe-48bc-ad8f-2eb882f39174") ) - (pad "C2" smd circle - (at 1.25 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "f184ea75-8d5e-4228-bd22-775881a868a8") + (fp_line + (start 1.4 -0.9) + (end -1.4 -0.9) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "05afcd40-b6e8-41bd-a0be-b3bf42356a68") ) - (pad "C3" smd circle - (at 1.25 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "680b978c-ba84-43e7-8cea-5f74b1dec1dc") + (fp_line + (start 1.4 0.9) + (end 1.4 -0.9) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "5f1d45e1-2b16-4411-bb38-4e490c9ee0af") ) - (pad "C4" smd circle - (at 1.25 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "9cac5b71-94c5-4a98-aa12-0e7a0c5d88a1") + (fp_text user "${REFERENCE}" + (at 0 2 0) + (layer "B.Fab") + (uuid "d005253a-9a8c-44de-80ac-a3c12bda21a3") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "C5" smd circle - (at 1.25 -12) - (size 0.6 0.6) + (pad "1" smd roundrect + (at -1.65 0) + (size 0.9 1.2) (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "d2793968-b83d-460f-924c-a4535e160118") + (roundrect_rratio 0.25) + (net "/Power_Control/PWR_LATCH_G") + (pinfunction "K_1") + (pintype "passive") + (uuid "82277a71-82be-47d6-b287-b6045f431d0d") ) - (pad "C6" smd circle - (at 1.25 -13.2) - (size 0.6 0.6) + (pad "2" smd roundrect + (at 1.65 0) + (size 0.9 1.2) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "3e2f3cc8-edff-49b4-96fa-edfa7fe1f907") + (roundrect_rratio 0.25) + (net "/MCU_Core/PWR_HOLD") + (pinfunction "A_2") + (pintype "passive") + (uuid "23c9bc63-3793-4295-ab44-99676ca47c98") ) - (pad "D0" smd circle - (at 2.75 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "5e4cc45b-a362-4228-9d0e-a9dbc0b5aa1f") + (embedded_fonts no) + (model "${KICAD10_3DMODEL_DIR}/Diode_SMD.3dshapes/D_SOD-123.step" + (offset + (xyz 0 0 0) + ) + (scale + (xyz 1 1 1) + ) + (rotate + (xyz 0 0 0) + ) ) - (pad "D1" smd circle - (at 2.75 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "28f543e8-3b55-4bdd-8c08-f57142326d00") + ) + (footprint "R2Builders:R2Builders" + (layer "B.Cu") + (uuid "9d267c25-cdf3-4271-ba57-016038d61e0a") + (at 137.5 110.2 180) + (property "Reference" "LOGO3" + (at 0 0 0) + (layer "B.SilkS") + (hide yes) + (uuid "874436e1-0bb9-4e9c-8680-a1abb4864743") + (effects + (font + (size 1.5 1.5) + (thickness 0.3) + ) + (justify mirror) + ) ) - (pad "D2" smd circle - (at 2.75 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "1b815e05-4acb-4960-82ab-db7d08092520") + (property "Value" "LOGO" + (at 0.75 0 0) + (layer "B.SilkS") + (hide yes) + (uuid "8df50e68-cf6d-4b3b-a531-6193ce9df95f") + (effects + (font + (size 1.5 1.5) + (thickness 0.3) + ) + (justify mirror) + ) ) - (pad "D3" smd circle - (at 2.75 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "d37a546d-55b8-4fbd-a2b3-1d69b65bacc0") + (property "Datasheet" "" + (at 0 0 0) + (layer "B.Fab") + (hide yes) + (uuid "f3b6ca63-3676-4551-827c-d45bab9f7218") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) ) - (pad "D4" smd circle - (at 2.75 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "37f4b72c-d6c2-43e5-8221-84586b24fe77") + (property "Description" "" + (at 0 0 0) + (layer "B.Fab") + (hide yes) + (uuid "d68ed663-7efa-4ec4-85fb-d7f5ea8a209d") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) ) - (pad "D5" smd circle - (at 2.75 -12) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "9a6e0c23-0b5c-4d74-9fd2-f92e223da089") + (property "Stackup Path" "" + (at 0 -2 0) + (layer "B.SilkS") + (hide yes) + (uuid "f16e7be7-953e-488e-b076-e08cfe558222") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) ) - (pad "D6" smd circle - (at 2.75 -13.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "98c6039f-3b26-41b1-b81f-03225c618259") + (property "Stackup Source" "" + (at 0 -2 0) + (layer "B.SilkS") + (hide yes) + (uuid "a8c13f84-09a1-4a0d-b13e-54f6b7c15af1") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) ) - (pad "E0" smd circle - (at 4.25 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "9c568f42-a2b0-46e7-b2c4-31e3ee38ed67") + (attr board_only exclude_from_pos_files exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (fp_poly + (pts + (xy 0.247393 1.665948) (xy 0.377249 1.625613) (xy 0.503787 1.552522) (xy 0.631778 1.44773) (xy 0.762235 1.310101) + (xy 0.856872 1.164927) (xy 0.914145 1.031604) (xy 0.934678 0.965416) (xy 0.936621 0.919549) (xy 0.91921 0.871586) + (xy 0.907935 0.849252) (xy 0.854988 0.77626) (xy 0.789963 0.727273) (xy 0.722577 0.704834) (xy 0.66255 0.711485) + (xy 0.619599 0.749769) (xy 0.610311 0.771388) (xy 0.545684 0.919999) (xy 0.452861 1.055293) (xy 0.339428 1.170639) + (xy 0.212971 1.259408) (xy 0.081075 1.314968) (xy -0.030093 1.331133) (xy -0.128328 1.321254) (xy -0.201366 1.287947) + (xy -0.252132 1.226573) (xy -0.28355 1.132491) (xy -0.298544 1.001059) (xy -0.300874 0.901423) (xy -0.297968 0.800173) + (xy -0.287387 0.70605) (xy -0.266562 0.609797) (xy -0.23292 0.502158) (xy -0.183891 0.373876) (xy -0.116906 0.215694) + (xy -0.099256 0.175396) (xy 0.000503 -0.053719) (xy 0.081048 -0.24381) (xy 0.142149 -0.394303) (xy 0.183578 -0.504626) + (xy 0.205107 -0.574206) (xy 0.208386 -0.595407) (xy 0.192742 -0.667678) (xy 0.151945 -0.735516) + (xy 0.095199 -0.792035) (xy 0.031709 -0.830347) (xy -0.029322 -0.843568) (xy -0.07869 -0.824811) + (xy -0.086702 -0.81618) (xy -0.10691 -0.779497) (xy -0.135055 -0.715158) (xy -0.156513 -0.65989) + (xy -0.181133 -0.597283) (xy -0.220584 -0.501941) (xy -0.270821 -0.383414) (xy -0.327803 -0.251253) + (xy -0.380337 -0.131205) (xy -0.462861 0.061124) (xy -0.525761 0.221367) (xy -0.57142 0.358182) + (xy -0.60222 0.480228) (xy -0.620542 0.596164) (xy -0.62877 0.714647) (xy -0.629836 0.775662) (xy -0.618254 0.977876) + (xy -0.57956 1.149791) (xy -0.510454 1.300825) (xy -0.407636 1.440395) (xy -0.390051 1.459896) (xy -0.258505 1.57469) + (xy -0.113301 1.646256) (xy 0.050743 1.676889) (xy 0.102951 1.678444) + ) + (stroke + (width 0) + (type solid) + ) + (fill yes) + (layer "B.SilkS") + (uuid "be607aa7-edde-4c00-8df5-3c0824506a99") ) - (pad "E1" smd circle - (at 4.25 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO6") - (uuid "50e64d8a-2ca6-423e-bdf8-5d437cadf4ed") + (fp_poly + (pts + (xy 0.798363 0.381916) (xy 0.801295 0.380876) (xy 0.823527 0.368418) (xy 0.838779 0.344697) (xy 0.849204 0.300854) + (xy 0.856957 0.228028) (xy 0.863828 0.123574) (xy 0.881058 -0.073143) (xy 0.910704 -0.25765) (xy 0.956281 -0.447424) + (xy 1.021282 -0.65989) (xy 1.091527 -0.856879) (xy 1.164019 -1.022306) (xy 1.245927 -1.167066) (xy 1.344417 -1.302052) + (xy 1.466656 -1.438159) (xy 1.61981 -1.586282) (xy 1.647295 -1.611489) (xy 1.830428 -1.782039) (xy 1.979421 -1.929278) + (xy 2.097493 -2.057261) (xy 2.187861 -2.170043) (xy 2.253742 -2.27168) (xy 2.298355 -2.366227) (xy 2.324917 -2.457738) + (xy 2.326914 -2.468008) (xy 2.329066 -2.595135) (xy 2.288029 -2.711736) (xy 2.20598 -2.816585) (xy 2.085095 -2.908454) + (xy 1.927551 -2.986118) (xy 1.735525 -3.048349) (xy 1.511192 -3.093922) (xy 1.25673 -3.121608) (xy 1.157702 -3.126979) + (xy 1.016513 -3.130877) (xy 0.912551 -3.129001) (xy 0.837038 -3.120863) (xy 0.78123 -3.105986) (xy 0.69272 -3.065751) + (xy 0.643176 -3.023831) (xy 0.625504 -2.97377) (xy 0.625159 -2.964006) (xy 0.646217 -2.886648) (xy 0.701188 -2.82022) + (xy 0.777767 -2.772761) (xy 0.86365 -2.752312) (xy 0.934325 -2.762011) (xy 1.059909 -2.790945) (xy 1.216615 -2.80287) + (xy 1.392724 -2.798353) (xy 1.576516 -2.777961) (xy 1.75627 -2.74226) (xy 1.84359 -2.718039) (xy 1.988477 -2.673288) + (xy 1.96092 -2.593712) (xy 1.918047 -2.501863) (xy 1.847691 -2.397634) (xy 1.747154 -2.27785) (xy 1.613741 -2.139334) + (xy 1.444754 -1.978911) (xy 1.41852 -1.954902) (xy 1.269663 -1.816864) (xy 1.150845 -1.70034) (xy 1.055928 -1.597932) + (xy 0.978779 -1.502241) (xy 0.91326 -1.405869) (xy 0.853238 -1.301417) (xy 0.814999 -1.227164) (xy 0.677663 -0.905334) + (xy 0.582648 -0.57364) (xy 0.528208 -0.22529) (xy 0.516861 -0.069171) (xy 0.511399 0.048383) (xy 0.509624 0.129431) + (xy 0.512855 0.183716) (xy 0.52241 0.220981) (xy 0.539609 0.250967) (xy 0.564358 0.281739) (xy 0.640781 0.349907) + (xy 0.722531 0.384868) + ) + (stroke + (width 0) + (type solid) + ) + (fill yes) + (layer "B.SilkS") + (uuid "dcbeac18-5cfe-4cf6-a74c-1529cb0e453c") ) - (pad "E2" smd circle - (at 4.25 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "2238f2e5-1ae9-4dba-b694-e45ff715a04c") + (fp_poly + (pts + (xy -1.673439 -0.295119) (xy -1.534248 -0.337431) (xy -1.35715 -0.4018) (xy -1.141504 -0.488453) + (xy -0.88667 -0.597619) (xy -0.694622 -0.683047) (xy -0.557857 -0.741846) (xy -0.402436 -0.804311) + (xy -0.251013 -0.861514) (xy -0.163708 -0.892239) (xy -0.058973 -0.929938) (xy 0.029798 -0.966327) + (xy 0.093144 -0.997228) (xy 0.121488 -1.018241) (xy 0.12683 -1.070422) (xy 0.102327 -1.136746) (xy 0.055613 -1.204159) + (xy -0.00568 -1.259601) (xy -0.027316 -1.272784) (xy -0.112517 -1.318404) (xy -0.371309 -1.231009) + (xy -0.490402 -1.188268) (xy -0.635012 -1.132521) (xy -0.788679 -1.070315) (xy -0.93494 -1.008198) + (xy -0.96635 -0.994368) (xy -1.080918 -0.943713) (xy -1.179669 -0.900424) (xy -1.255292 -0.867675) + (xy -1.300479 -0.848643) (xy -1.310009 -0.845122) (xy -1.306913 -0.863897) (xy -1.289976 -0.910493) + (xy -1.283869 -0.925418) (xy -1.260803 -0.999065) (xy -1.250371 -1.068799) (xy -1.250319 -1.072655) + (xy -1.250319 -1.139597) (xy -1.059298 -1.152418) (xy -0.902461 -1.17163) (xy -0.750657 -1.206074) + (xy -0.611446 -1.252543) (xy -0.492385 -1.307828) (xy -0.401034 -1.36872) (xy -0.344952 -1.432011) + (xy -0.333184 -1.460621) (xy -0.334557 -1.528569) (xy -0.360767 -1.609874) (xy -0.403332 -1.68657) + (xy -0.453769 -1.740689) (xy -0.469901 -1.750176) (xy -0.506471 -1.759856) (xy -0.54722 -1.750769) + (xy -0.605084 -1.718744) (xy -0.641464 -1.694855) (xy -0.787006 -1.619459) (xy -0.956949 -1.567731) + (xy -1.13358 -1.544092) (xy -1.239862 -1.545574) (xy -1.307644 -1.552259) (xy -1.359176 -1.563524) + (xy -1.405951 -1.585388) (xy -1.459462 -1.623868) (xy -1.531203 -1.684982) (xy -1.567729 -1.717248) + (xy -1.670431 -1.808077) (xy -1.785773 -1.909832) (xy -1.893402 -2.004564) (xy -1.923082 -2.030631) + (xy -2.048385 -2.147266) (xy -2.138648 -2.246068) (xy -2.192613 -2.325322) (xy -2.209022 -2.383315) + (xy -2.199945 -2.407649) (xy -2.152043 -2.444983) (xy -2.078563 -2.468771) (xy -1.974572 -2.479559) + (xy -1.835137 -2.477892) (xy -1.672662 -2.465953) (xy -1.540779 -2.454689) (xy -1.447558 -2.449429) + (xy -1.385742 -2.450176) (xy -1.348075 -2.456934) (xy -1.33114 -2.466088) (xy -1.303147 -2.516348) + (xy -1.298047 -2.59078) (xy -1.314817 -2.673897) (xy -1.349616 -2.746119) (xy -1.377524 -2.783925) + (xy -1.407175 -2.808935) (xy -1.449851 -2.825727) (xy -1.516839 -2.838875) (xy -1.610099 -2.851746) + (xy -1.799826 -2.871394) (xy -1.967778 -2.878838) (xy -2.107307 -2.87414) (xy -2.211766 -2.857363) + (xy -2.245779 -2.845795) (xy -2.368056 -2.771817) (xy -2.451296 -2.674747) (xy -2.494557 -2.557816) + (xy -2.496902 -2.424255) (xy -2.45739 -2.277296) (xy -2.429246 -2.214664) (xy -2.382469 -2.131173) + (xy -2.323507 -2.046303) (xy -2.247734 -1.95495) (xy -2.150525 -1.85201) (xy -2.027255 -1.732379) + (xy -1.873296 -1.590951) (xy -1.823571 -1.546314) (xy -1.702867 -1.435637) (xy -1.612125 -1.346436) + (xy -1.553416 -1.280886) (xy -1.528815 -1.241159) (xy -1.528168 -1.236742) (xy -1.538172 -1.194502) + (xy -1.564535 -1.125567) (xy -1.601785 -1.044083) (xy -1.606009 -1.035565) (xy -1.649425 -0.94397) + (xy -1.687984 -0.854403) (xy -1.713 -0.787237) (xy -1.737361 -0.717499) (xy -1.764116 -0.676498) + (xy -1.807158 -0.651612) (xy -1.880377 -0.630221) (xy -1.887978 -0.628277) (xy -1.957631 -0.604718) + (xy -2.008634 -0.577005) (xy -2.021731 -0.564033) (xy -2.035144 -0.503384) (xy -2.015452 -0.432198) + (xy -1.970097 -0.362318) (xy -1.906515 -0.305587) (xy -1.840655 -0.275755) (xy -1.775361 -0.274636) + ) + (stroke + (width 0) + (type solid) + ) + (fill yes) + (layer "B.SilkS") + (uuid "767c233e-88c4-4cde-b45c-3643340fb744") ) - (pad "E3" smd circle - (at 4.25 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "a761a27c-e7a6-44c1-abaf-09d58349e4de") + (fp_poly + (pts + (xy 0.550775 3.120374) (xy 0.793163 3.071376) (xy 1.00362 2.989746) (xy 1.182836 2.87525) (xy 1.263406 2.803152) + (xy 1.375653 2.669144) (xy 1.463026 2.514071) (xy 1.527635 2.332204) (xy 1.571588 2.11781) (xy 1.594444 1.903473) + (xy 1.609207 1.697611) (xy 1.882353 1.574117) (xy 2.009342 1.513276) (xy 2.135462 1.446775) (xy 2.253337 1.379149) + (xy 2.355591 1.314936) (xy 2.434846 1.258671) (xy 2.483727 1.21489) (xy 2.495168 1.197268) (xy 2.48167 1.196284) + (xy 2.437348 1.217293) (xy 2.369747 1.25636) (xy 2.311861 1.292834) (xy 2.205961 1.35934) (xy 2.100439 1.421735) + (xy 2.003928 1.475308) (xy 1.925061 1.515348) (xy 1.872469 1.537143) (xy 1.859443 1.539746) (xy 1.870093 1.529298) + (xy 1.913272 1.501284) (xy 1.981068 1.460697) (xy 2.022903 1.436578) (xy 2.13043 1.371687) (xy 2.22992 1.305095) + (xy 2.313937 1.242462) (xy 2.375042 1.189449) (xy 2.405799 1.151717) (xy 2.408021 1.143464) (xy 2.39111 1.142856) + (xy 2.347342 1.164722) (xy 2.30149 1.194043) (xy 2.240539 1.231231) (xy 2.149851 1.280831) (xy 2.040598 1.337332) + (xy 1.923948 1.395223) (xy 1.811073 1.448992) (xy 1.713142 1.493127) (xy 1.641327 1.522117) (xy 1.626718 1.526984) + (xy 1.589848 1.532888) (xy 1.586231 1.513526) (xy 1.588731 1.506383) (xy 1.61465 1.479561) (xy 1.671616 1.439645) + (xy 1.749034 1.393797) (xy 1.779607 1.377357) (xy 1.880681 1.320823) (xy 1.98258 1.257633) (xy 2.078083 1.193048) + (xy 2.159974 1.132333) (xy 2.221035 1.080749) (xy 2.254046 1.04356) (xy 2.256892 1.02934) (xy 2.230699 1.025584) + (xy 2.184854 1.051903) (xy 2.183317 1.053103) (xy 2.12643 1.08841) (xy 2.082125 1.099139) (xy 2.061175 1.083117) + (xy 2.060711 1.077846) (xy 2.041687 1.071041) (xy 1.984388 1.088164) (xy 1.888474 1.12935) (xy 1.753607 1.194733) + (xy 1.7134 1.21506) (xy 1.542533 1.297527) (xy 1.342353 1.386876) (xy 1.127757 1.47698) (xy 0.939893 1.551323) + (xy 1.806016 1.551323) (xy 1.817593 1.539746) (xy 1.82917 1.551323) (xy 1.817593 1.5629) (xy 1.806016 1.551323) + (xy 0.939893 1.551323) (xy 0.91364 1.561712) (xy 0.878997 1.574477) (xy 1.759708 1.574477) (xy 1.771285 1.5629) + (xy 1.782862 1.574477) (xy 1.771285 1.586054) (xy 1.759708 1.574477) (xy 0.878997 1.574477) (xy 0.816159 1.597631) + (xy 1.7134 1.597631) (xy 1.724977 1.586054) (xy 1.736554 1.597631) (xy 1.724977 1.609208) (xy 1.7134 1.597631) + (xy 0.816159 1.597631) (xy 0.753321 1.620785) (xy 1.667092 1.620785) (xy 1.678669 1.609208) (xy 1.690246 1.620785) + (xy 1.678669 1.632362) (xy 1.667092 1.620785) (xy 0.753321 1.620785) (xy 0.714897 1.634943) (xy 0.592051 1.676354) + (xy 0.439522 1.72182) (xy 0.272965 1.765806) (xy 0.099428 1.806998) (xy -0.07404 1.844081) (xy -0.240393 1.875742) + (xy -0.39258 1.900668) (xy -0.523556 1.917545) (xy -0.62627 1.925059) (xy -0.693676 1.921897) (xy -0.706646 1.918412) + (xy -0.735789 1.914662) (xy -0.738301 1.924223) (xy -0.72631 1.954762) (xy -0.70252 2.016603) (xy -0.675745 2.086736) + (xy -0.460494 2.086736) (xy -0.452433 2.050637) (xy -0.415019 2.028367) (xy -0.359701 2.031049) + (xy -0.306047 2.056429) (xy -0.292313 2.069098) (xy -0.254049 2.130481) (xy -0.227031 2.208048) + (xy -0.217541 2.280479) (xy -0.221633 2.309087) (xy -0.251959 2.34346) (xy -0.301851 2.347431) (xy -0.357378 2.322575) + (xy -0.39133 2.289904) (xy -0.427561 2.227008) (xy -0.45214 2.153318) (xy -0.460494 2.086736) (xy -0.675745 2.086736) + (xy -0.671541 2.097747) (xy -0.663483 2.118934) (xy -0.611039 2.25508) (xy -0.570878 2.353296) (xy -0.539743 2.419271) + (xy -0.514376 2.458698) (xy -0.491519 2.477266) (xy -0.467916 2.480669) (xy -0.45737 2.479023) (xy -0.435274 2.474244) + (xy -0.402186 2.466807) (xy -0.353038 2.455534) (xy -0.282761 2.439248) (xy -0.186285 2.416771) + (xy -0.058542 2.386926) (xy 0.105538 2.348535) (xy 0.250226 2.314659) (xy 0.347488 2.284867) (xy 0.478888 2.233742) + (xy 0.638778 2.163645) (xy 0.82151 2.07694) (xy 0.83792 2.068877) (xy 1.256427 1.862715) (xy 1.24236 1.950136) + (xy 1.18961 2.165157) (xy 1.105133 2.346906) (xy 0.98747 2.497157) (xy 0.835167 2.617681) (xy 0.646766 2.710252) + (xy 0.605402 2.725299) (xy 0.534634 2.747549) (xy 0.466395 2.762701) (xy 0.389116 2.772043) (xy 0.291224 2.776861) + (xy 0.16115 2.778444) (xy 0.127347 2.778485) (xy -0.005182 2.777819) (xy -0.102318 2.774872) (xy -0.17497 2.76822) + (xy -0.234047 2.756436) (xy -0.290454 2.738096) (xy -0.342565 2.717082) (xy -0.432213 2.676164) + (xy -0.517029 2.632248) (xy -0.568584 2.601314) (xy -0.605277 2.573183) (xy -0.643554 2.536347) + (xy -0.684882 2.488193) (xy -0.730729 2.42611) (xy -0.782561 2.347484) (xy -0.841848 2.249704) (xy -0.910057 2.130157) + (xy -0.988655 1.986231) (xy -1.07911 1.815313) (xy -1.18289 1.61479) (xy -1.301462 1.382051) (xy -1.436294 1.114483) + (xy -1.588853 0.809474) (xy -1.695211 0.595949) (xy -1.824884 0.336627) (xy -1.935889 0.117593) + (xy -2.029125 -0.062836) (xy -2.105495 -0.206342) (xy -2.1659 -0.314607) (xy -2.211241 -0.389313) + (xy -2.24242 -0.432143) (xy -2.250486 -0.440195) (xy -2.325843 -0.486521) (xy -2.392349 -0.495325) + (xy -2.442597 -0.466507) (xy -2.457145 -0.442995) (xy -2.464021 -0.417767) (xy -2.461698 -0.384601) + (xy -2.4478 -0.336935) (xy -2.41995 -0.268206) (xy -2.375774 -0.171849) (xy -2.312895 -0.041301) + (xy -2.308365 -0.032011) (xy -2.134608 0.324158) (xy -2.190276 0.345993) (xy -2.232284 0.374968) + (xy -2.245845 0.403878) (xy -2.235922 0.432844) (xy -2.208264 0.496817) (xy -2.165964 0.589443) + (xy -2.112113 0.704368) (xy -2.049803 0.835238) (xy -1.982127 0.975699) (xy -1.912176 1.119396) + (xy -1.843041 1.259978) (xy -1.777816 1.391088) (xy -1.719591 1.506374) (xy -1.671459 1.599481) + (xy -1.636512 1.664056) (xy -1.6186 1.692879) (xy -1.567003 1.719548) (xy -1.511699 1.720012) (xy -1.480372 1.717519) + (xy -1.455164 1.722603) (xy -1.430929 1.741467) (xy -1.402521 1.780313) (xy -1.364794 1.845343) + (xy -1.312603 1.942759) (xy -1.28764 1.990065) (xy -1.19433 2.165231) (xy -1.117032 2.305404) (xy -1.051441 2.417202) + (xy -0.99325 2.507244) (xy -0.938153 2.582149) (xy -0.881844 2.648536) (xy -0.820017 2.713023) (xy -0.812347 2.720628) + (xy -0.616776 2.882945) (xy -0.399206 3.005104) (xy -0.158835 3.087411) (xy 0.105135 3.130172) (xy 0.275764 3.136973) + ) + (stroke + (width 0) + (type solid) + ) + (fill yes) + (layer "B.SilkS") + (uuid "d809c03c-8105-4977-8fc7-0f155e92ce4a") ) - (pad "E4" smd circle - (at 4.25 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/USB_DP") - (uuid "43ed24e4-5931-43d9-b511-29d9b68d1d60") + (embedded_fonts no) + ) + (footprint "Resistor_SMD:R_0402_1005Metric" + (layer "B.Cu") + (uuid "9e33b6f7-03b2-48f7-b4c7-a067ef43611a") + (at 132.285 74.44) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_LATCH_G1" + (at 0 1.17 0) + (layer "B.SilkS") + (hide yes) + (uuid "756ad045-de34-4aa5-8583-720c28e841a7") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "E5" smd circle - (at 4.25 -12) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/USB_DM") - (uuid "e084750c-f7ca-47d4-a8bb-259f002afcdb") + (property "Value" "1MΩ" + (at 0 -1.17 0) + (layer "B.Fab") + (uuid "144004f1-efc5-48c5-b085-980750e018e8") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "E6" smd circle - (at 4.25 -13.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "cf3d0d43-9a71-437a-bfb3-83e2ce6a8d1c") + (property "Datasheet" "" + (at 0 0 0) + (layer "B.Fab") + (hide yes) + (uuid "7a42ab1b-ab89-43be-953f-d26b2c555bba") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) ) - (pad "F0" smd rect - (at -2.875 -4) - (size 1.5 1.5) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "7c808d42-9479-4cbf-895e-54363052eff4") + (property "Description" "Resistor" + (at 0 0 0) + (layer "B.Fab") + (hide yes) + (uuid "169e50fe-dd62-42f7-99b3-e773cff71e83") + (effects + (font + (size 1.27 1.27) + ) + (justify mirror) + ) ) - (pad "F1" smd rect - (at -0.625 -4) - (size 1.5 1.5) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "8a1b9ed3-6130-4368-9b97-bf7137ace351") + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "fc5a3232-9451-4f44-894c-50744c0715c5") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "F2" smd rect - (at 1.625 -4) - (size 1.5 1.5) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "52774989-8cf8-457d-bf3d-45874e651fdb") + (property "Manufacturer_Part_Number" "0402WGF1004TCE" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "865ca63a-e1ea-472b-81be-bb28866642bc") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "F3" smd rect - (at 3.875 -4) - (size 1.5 1.5) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "62cb5202-a3c1-4b0d-85c8-ac9d3659dcb5") + (property "LCSC" "C26083" + (at 0 0 0) + (unlocked yes) + (layer "B.Fab") + (hide yes) + (uuid "90ac7081-6eea-4866-a57b-150b0eda4acb") + (effects + (font + (size 1 1) + (thickness 0.15) + ) + (justify mirror) + ) ) - (pad "F4" smd circle - (at 5.75 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/3V3_RF") - (uuid "10a3f117-64a7-498e-bc67-27f967a4dea8") + (property "Stackup Path" "R_LATCH_G1" + (at -2 0 270) + (layer "B.SilkS") + (hide yes) + (uuid "37ba0831-6e75-457e-bd89-6155e55bffb1") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) ) - (pad "F5" smd circle - (at 5.75 -12) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (uuid "57b4100f-dcdb-48c8-ab46-04787669444e") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:66" + (at -2 0 270) + (layer "B.SilkS") + (hide yes) + (uuid "f977c22e-19ee-408b-8c39-8abe64ba336f") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + ) ) - (pad "F6" smd rect - (at 5.75 -13.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "VBUS") - (uuid "f7d09daa-29e2-4c64-bec9-60abe7406768") + (property ki_fp_filters "R_*") + (path "/69e3e4db-a3ee-5e94-9e3d-5b01833af909") + (units + (unit + (name "A") + (pins "1" "2") + ) ) - (pad "Z0" smd circle - (at -3.25 -6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO4") - (uuid "5bc658db-937c-4d70-805e-b0f384037b0c") + (attr smd) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start -0.153641 -0.38) + (end 0.153641 -0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "86f8ddc0-59e9-498c-8996-cfe1f4fa18d8") ) - (pad "Z1" smd circle - (at -3.25 -7.2) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "ACCEL_INT1") - (uuid "ff204d92-1405-4884-8a6a-cfdc535a8ee8") + (fp_line + (start -0.153641 0.38) + (end 0.153641 0.38) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "e8813b4d-e697-488b-abd0-9429d007de62") ) - (pad "Z2" smd circle - (at -3.25 -8.4) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/PWR_HOLD") - (uuid "7ff36ba1-b6eb-4a1d-88eb-c464cc7066e5") + (fp_rect + (start -0.93 0.47) + (end 0.93 -0.47) + (stroke + (width 0.05) + (type solid) + ) + (fill no) + (layer "B.CrtYd") + (uuid "59f10495-0769-44d6-94f4-e57cfa5318dd") ) - (pad "Z3" smd circle - (at -3.25 -9.6) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/STAT1") - (uuid "ab9c0766-2a59-4057-8815-a3a4784a346d") + (fp_rect + (start -0.525 0.27) + (end 0.525 -0.27) + (stroke + (width 0.1) + (type solid) + ) + (fill no) + (layer "B.Fab") + (uuid "0c0178d2-5757-4f74-b03b-2c576ab49f1b") ) - (pad "Z4" smd circle - (at -3.25 -10.8) - (size 0.6 0.6) - (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/STAT2") - (uuid "4f8151a4-2258-48b7-b9f3-e0273a30ab7d") + (fp_text user "${REFERENCE}" + (at 0 0 0) + (layer "B.Fab") + (uuid "c1abb47d-330d-4ec7-829a-66c7979cf1a9") + (effects + (font + (size 0.26 0.26) + (thickness 0.04) + ) + (justify mirror) + ) ) - (pad "Z5" smd circle - (at -3.25 -12) - (size 0.6 0.6) + (pad "1" smd roundrect + (at -0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_MACRO1") - (uuid "f6161305-6ac6-4a95-aa1d-60ab8220b441") + (roundrect_rratio 0.25) + (net "GND") + (pintype "passive") + (uuid "8a4b74b5-ab1f-41d0-b563-b734d4809bf3") ) - (pad "Z6" smd circle - (at -3.25 -13.2) - (size 0.6 0.6) + (pad "2" smd roundrect + (at 0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "0ec7eb56-03dd-4784-9f58-e2d3f1b5e7e5") + (roundrect_rratio 0.25) + (net "/Power_Control/PWR_LATCH_G") + (pintype "passive") + (uuid "9d2b1677-ef53-437a-9b45-1474ab7b27a8") ) (embedded_fonts no) - (model "${KIPRJMOD}/libraries/3dmodels/BT840X_outline.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset - (xyz 0 -0.3 0.3) + (xyz 0 0 0) ) (scale (xyz 1 1 1) ) (rotate - (xyz -90 0 0) + (xyz 0 0 0) ) ) ) - (footprint "C_0402_1005Metric" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "ba9ed94b-da9e-4ee5-a124-3e8ac9523be1") - (at 144.75 70 180) - (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_IMU_3" - (at 0 1.16 0) + (uuid "a4ce15da-b062-4697-8f6c-88071faa9cc9") + (at 138.525 101 -90) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_FB2" + (at 0 1.17 90) (layer "B.SilkS") (hide yes) - (uuid "ac3963c6-d070-40be-bc30-cddd2f0ffdd5") + (uuid "657b7bc4-b526-47be-9364-0d4bd6856dba") (effects (font (size 1 1) @@ -23801,10 +23734,10 @@ (justify mirror) ) ) - (property "Value" "10nF" - (at 0 -1.16 0) + (property "Value" "56.2kΩ" + (at 0 -1.17 90) (layer "B.Fab") - (uuid "1913cbc6-a6fe-4ff7-a3c0-1b09397d45f2") + (uuid "aac1a616-6278-4b71-97eb-21182b6aeb57") (effects (font (size 1 1) @@ -23814,10 +23747,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "f3cc5335-edce-43c5-b10f-c9b24a08cac0") + (uuid "d54b317e-51c3-4da8-bebe-8f8abee204ff") (effects (font (size 1.27 1.27) @@ -23825,11 +23758,11 @@ (justify mirror) ) ) - (property "Description" "" - (at 0 0 0) + (property "Description" "Resistor" + (at 0 0 90) (layer "B.Fab") (hide yes) - (uuid "01615a5b-5cf1-4e09-ad54-cc6a683113e5") + (uuid "fdb2d46c-014b-4f70-87cd-25a35ca20c0a") (effects (font (size 1.27 1.27) @@ -23837,11 +23770,12 @@ (justify mirror) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 0) - (layer "B.SilkS") + (property "MF" "Yageo" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "a2ed97b4-ed8b-4b49-9525-ea033a24ae36") + (uuid "411c0b8e-0750-49af-bd77-3338b0c7f631") (effects (font (size 1 1) @@ -23850,146 +23784,142 @@ (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 0) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "RC0402FR-0756K2L" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "f3dcb57d-804c-4964-836c-be5d4d7c2885") + (uuid "eaf70b90-dfb1-4adb-9a58-5b698a6fd7cb") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL05B103KB5NNNC" - (at 0 -2 0) - (layer "B.SilkS") + (property "LCSC" "C183355" + (at 0 0 270) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "9920841f-16d0-4136-94e8-5d4df13e711a") + (uuid "b93defc4-a0e3-4f40-a6b2-a9179885ef39") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C15195" - (at 0 -2 0) + (property "Stackup Path" "R_FB2" + (at 2 0 180) (layer "B.SilkS") (hide yes) - (uuid "e124a35b-6d7f-4bba-9a34-f455ecffbac2") + (uuid "88efd99b-935a-4ae5-bfe2-17dface683bc") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Path" "C_IMU_3" - (at 0 -2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:61" + (at 2 0 180) (layer "B.SilkS") (hide yes) - (uuid "b66c9788-e30d-4f87-8d6e-5ce169081054") + (uuid "302c5a6d-e7eb-47cc-92a7-a0b453221a4c") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:29" - (at 0 -2 0) - (layer "B.SilkS") - (hide yes) - (uuid "b370167f-9712-4966-904e-05166ae3f2ce") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (property ki_fp_filters "R_*") + (path "/31d3531d-3c70-537f-859f-5b6468e07c16") + (units + (unit + (name "A") + (pins "1" "2") ) ) - (path "/2ab33b9d-8ad8-5337-89d8-d4014f8c2dae") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "d074f99a-3dff-452b-b8bf-4cf1dac6703c") + (uuid "4f6c69c9-6045-4f06-96df-0d96af307b7e") ) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "24099106-a462-48e8-a330-3065ca52bb15") + (uuid "d275a0a7-fe19-4c3e-8cb9-3a6798a6a33e") ) (fp_rect - (start -0.91 0.46) - (end 0.91 -0.46) + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "B.CrtYd") - (uuid "2b16c0e5-09b8-499e-b517-d5de04e1d78c") + (uuid "f8d236ee-67bb-4b95-96e6-9e8bcf560895") ) (fp_rect - (start -0.5 0.25) - (end 0.5 -0.25) + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "2331fa06-544c-4693-8a8b-df603e2bc733") + (uuid "0accf6b2-8e85-4434-ba83-edc0b8bc808c") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 90) (layer "B.Fab") - (uuid "a9e7f3c2-ba51-4825-b0bf-f2074442a350") + (uuid "cdf62203-c9fe-42ce-a43b-c843c3be93f5") (effects (font - (size 0.25 0.25) + (size 0.26 0.26) (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.48 0 180) - (size 0.56 0.62) + (at -0.51 0 270) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "3V3") - (uuid "bc1860b9-fabf-4304-a25a-5dc76ef998ea") + (net "/Power_Buck/BUCK_FB") + (pintype "passive") + (uuid "d959f9cc-2458-497a-ac23-1d2aa59eff99") ) (pad "2" smd roundrect - (at 0.48 0 180) - (size 0.56 0.62) + (at 0.51 0 270) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) (net "GND") - (uuid "1b44d5bd-6528-4965-8064-e65f80bb3240") + (pintype "passive") + (uuid "e6b47b47-bd89-4639-9955-f08d4cd3b63c") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -24003,15 +23933,15 @@ ) (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "c76f16eb-c754-4fa8-a812-bda93b6b357c") - (at 130.775 123.815) + (uuid "b611f9d7-d56c-4eb1-818b-431aae6bb97d") + (at 121.77 99.75 180) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_CC1" - (at 0 1.17 0) + (property "Reference" "R_VSET1" + (at 0 1.17 180) (layer "B.SilkS") (hide yes) - (uuid "9d2ee31c-7e2a-4731-9d51-901bba8c2132") + (uuid "788fa6c2-8508-4acf-b5c7-6c254230d563") (effects (font (size 1 1) @@ -24020,10 +23950,10 @@ (justify mirror) ) ) - (property "Value" "5.1kΩ" - (at 0 -1.17 0) + (property "Value" "18kΩ" + (at 0 -1.17 180) (layer "B.Fab") - (uuid "073dee7c-4415-4a5d-90a5-95dd74494753") + (uuid "7e793424-fb67-4346-b4a3-298fb9739d26") (effects (font (size 1 1) @@ -24033,10 +23963,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "e02f30a1-0820-4767-b493-3c9c937a839e") + (uuid "7be390f6-0de0-437a-adb8-0f4706085985") (effects (font (size 1.27 1.27) @@ -24045,10 +23975,10 @@ ) ) (property "Description" "Resistor" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "dd5ccccd-33da-45ec-974e-22f870e0db44") + (uuid "c214e183-718d-473a-b8b4-a48e4d7171a6") (effects (font (size 1.27 1.27) @@ -24056,12 +23986,12 @@ (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (property "MF" "Yageo" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "5c60373e-ab8d-40c4-a710-aa15146ef450") + (uuid "abdfede7-c5df-484b-b4a9-89be27dbf551") (effects (font (size 1 1) @@ -24070,12 +24000,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF5101TCE" + (property "Manufacturer_Part_Number" "RC0402FR-0718KL" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "b8435940-db2a-4fe2-95be-ccd8d1961e9d") + (uuid "3a5e1a67-1cc8-4390-92cf-25c266317159") (effects (font (size 1 1) @@ -24084,12 +24014,12 @@ (justify mirror) ) ) - (property "LCSC" "C25905" + (property "LCSC" "C138044" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "28d4cce8-c77c-48b3-913c-9c9df549d685") + (uuid "eba6b239-6c3f-446a-9ff0-b5fe86b3c25d") (effects (font (size 1 1) @@ -24098,34 +24028,32 @@ (justify mirror) ) ) - (property "Stackup Path" "R_CC1" - (at 2 0 90) + (property "Stackup Path" "R_VSET1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "619ef3d5-45d7-4c73-a5e0-23ba0e944c3c") + (uuid "9dad4451-51f8-446f-87ff-437d8849c86d") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:55" - (at 2 0 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:74" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "66337094-c578-49a4-a89f-87fb26533af6") + (uuid "723c59b0-8588-4b69-a946-e825eddd2d13") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) (property ki_fp_filters "R_*") - (path "/ed5d7f5c-8fa0-5dc7-9d3e-fe8638f144ed") + (path "/b59483be-69ee-57e4-ae87-bfff111ed616") (units (unit (name "A") @@ -24135,24 +24063,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "01570a01-fa34-4f59-9ced-c8f6a242dbf8") + (uuid "5251846c-946e-4205-b5f2-4d5e6582c7b5") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "07974829-4925-4e43-b8d1-1ba1e0d6e749") + (uuid "ee1c1b33-865f-4024-9606-dbaa5b1627e9") ) (fp_rect (start -0.93 0.47) @@ -24163,7 +24091,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "f69587d1-53d6-4da9-99c6-28b54df59b38") + (uuid "ba51f0a8-5f56-42ab-86df-42647b3f3a72") ) (fp_rect (start -0.525 0.27) @@ -24174,12 +24102,12 @@ ) (fill no) (layer "B.Fab") - (uuid "7fd33140-3e83-44ec-b1a6-c118d3c14db4") + (uuid "e87be81b-2d46-4c4b-aa22-bae4a5c27ddb") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") - (uuid "0f59184e-bd23-4a4c-941b-bd9c3f1ed4cf") + (uuid "9bbc928e-40ca-446f-9c1c-de502c9d80e8") (effects (font (size 0.26 0.26) @@ -24189,22 +24117,22 @@ ) ) (pad "1" smd roundrect - (at -0.51 0) + (at -0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/USB_C/USB_CC1") + (net "/Power_Charger/CHG_VSET") (pintype "passive") - (uuid "d8d01e7e-29c5-4c2a-aede-7bb8ae77a4fb") + (uuid "0115e654-db8a-447a-8bd5-7aa3e4514211") ) (pad "2" smd roundrect - (at 0.51 0) + (at 0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) (net "GND") (pintype "passive") - (uuid "0d0ace54-f86e-43bb-8e5e-6c99f498f9e3") + (uuid "d26b3470-e240-43db-a1fb-823782b4c158") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -24219,17 +24147,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0402_1005Metric" + (footprint "C_0402_1005Metric" (layer "B.Cu") - (uuid "ca4cc822-1396-4067-bc37-2989a1e547e5") - (at 144.555 95.505 90) + (uuid "ba9ed94b-da9e-4ee5-a124-3e8ac9523be1") + (at 127.18 128.5 180) (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") - (property "Reference" "C_3V3_2" - (at 0 1.16 270) + (property "Reference" "C_IMU_3" + (at 0 1.16 0) (layer "B.SilkS") (hide yes) - (uuid "3433c062-6fe5-4dbe-8353-7e2cd8228e5b") + (uuid "ac3963c6-d070-40be-bc30-cddd2f0ffdd5") (effects (font (size 1 1) @@ -24238,10 +24166,10 @@ (justify mirror) ) ) - (property "Value" "100nF" - (at 0 -1.16 270) + (property "Value" "10nF" + (at 0 -1.16 0) (layer "B.Fab") - (uuid "47e8f512-7114-4085-b25d-44a4a9835374") + (uuid "1913cbc6-a6fe-4ff7-a3c0-1b09397d45f2") (effects (font (size 1 1) @@ -24251,10 +24179,10 @@ ) ) (property "Datasheet" "" - (at 0 0 270) + (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "adac23db-5313-4fdc-8aff-cf571c7789c8") + (uuid "f3cc5335-edce-43c5-b10f-c9b24a08cac0") (effects (font (size 1.27 1.27) @@ -24262,11 +24190,11 @@ (justify mirror) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 270) + (property "Description" "" + (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "c6843d3e-5773-4488-acd9-3af0e3b0f331") + (uuid "01615a5b-5cf1-4e09-ad54-cc6a683113e5") (effects (font (size 1.27 1.27) @@ -24274,12 +24202,11 @@ (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 0 270) - (unlocked yes) - (layer "B.Fab") + (property "KiLib_Generator" "SMD_2terminal_chip_molded" + (at 0 0 0) + (layer "B.SilkS") (hide yes) - (uuid "32c794a1-68ab-47dc-89e5-098e3776a769") + (uuid "a2ed97b4-ed8b-4b49-9525-ea033a24ae36") (effects (font (size 1 1) @@ -24288,39 +24215,37 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 270) - (unlocked yes) - (layer "B.Fab") + (property "MF" "Samsung Electro-Mechanics" + (at 0 -2 0) + (layer "B.SilkS") (hide yes) - (uuid "c3166ad1-28ae-4f86-8614-0132c01396f9") + (uuid "f3dcb57d-804c-4964-836c-be5d4d7c2885") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C1525" - (at 0 0 270) - (unlocked yes) - (layer "B.Fab") + (property "Manufacturer_Part_Number" "CL05B103KB5NNNC" + (at 0 -2 0) + (layer "B.SilkS") (hide yes) - (uuid "30778bb9-0cc4-4c3e-801d-d6d01078c321") + (uuid "9920841f-16d0-4136-94e8-5d4df13e711a") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Path" "C_3V3_2" - (at 2 0 0) + (property "LCSC" "C15195" + (at 0 -2 0) (layer "B.SilkS") (hide yes) - (uuid "063a48ed-2a44-4cf7-90dd-b760708edd22") + (uuid "e124a35b-6d7f-4bba-9a34-f455ecffbac2") (effects (font (size 1.27 1.27) @@ -24329,11 +24254,11 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:22" - (at 2 0 0) + (property "Stackup Path" "C_IMU_3" + (at 0 -2 0) (layer "B.SilkS") (hide yes) - (uuid "b0014fce-7c4a-4267-b2dc-e5a823ee9019") + (uuid "b66c9788-e30d-4f87-8d6e-5ce169081054") (effects (font (size 1.27 1.27) @@ -24342,35 +24267,41 @@ (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/008fd044-38d8-5b0c-a9aa-e2799ecdf39b") - (units - (unit - (name "A") - (pins "1" "2") + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:31" + (at 0 -2 0) + (layer "B.SilkS") + (hide yes) + (uuid "b370167f-9712-4966-904e-05166ae3f2ce") + (effects + (font + (size 1.27 1.27) + (thickness 0.15) + ) + (justify mirror) ) ) + (path "/2ab33b9d-8ad8-5337-89d8-d4014f8c2dae") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "a5ad6d04-fbf4-4e6e-80dd-796da04a7f27") + (uuid "d074f99a-3dff-452b-b8bf-4cf1dac6703c") ) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "442cbd50-4ae2-4705-bed2-d0fdbb666ed0") + (uuid "24099106-a462-48e8-a330-3065ca52bb15") ) (fp_rect (start -0.91 0.46) @@ -24381,7 +24312,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "9e7757e3-6e00-43a6-8d9b-3d197173d7ce") + (uuid "2b16c0e5-09b8-499e-b517-d5de04e1d78c") ) (fp_rect (start -0.5 0.25) @@ -24392,12 +24323,12 @@ ) (fill no) (layer "B.Fab") - (uuid "ccbc299d-c428-4544-b7aa-ab47e8db76a8") + (uuid "2331fa06-544c-4693-8a8b-df603e2bc733") ) (fp_text user "${REFERENCE}" - (at 0 0 270) + (at 0 0 0) (layer "B.Fab") - (uuid "87cf8e1b-4a69-45d2-95a4-cb2a08785ca0") + (uuid "a9e7f3c2-ba51-4825-b0bf-f2074442a350") (effects (font (size 0.25 0.25) @@ -24407,22 +24338,20 @@ ) ) (pad "1" smd roundrect - (at -0.48 0 90) + (at -0.48 0 180) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") - (pintype "passive") - (uuid "86978152-f2d0-4efd-b75d-f23d9f97e1bc") + (net "3V3") + (uuid "bc1860b9-fabf-4304-a25a-5dc76ef998ea") ) (pad "2" smd roundrect - (at 0.48 0 90) + (at 0.48 0 180) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) (net "GND") - (pintype "passive") - (uuid "57f52144-7359-4b8d-a560-d4f69d74d24d") + (uuid "1b44d5bd-6528-4965-8064-e65f80bb3240") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0402_1005Metric.step" @@ -24437,17 +24366,17 @@ ) ) ) - (footprint "Capacitor_SMD:C_0603_1608Metric" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "cad46504-6d0e-4285-af11-4a75d8535790") - (at 143.075 91.375) - (descr "Capacitor SMD 0603 (1608 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_3V3_1" - (at 0 1.43 0) + (uuid "bc301f15-db6e-4666-91d7-22b9bf096c69") + (at 124.16 97.25 180) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_STAT1" + (at 0 1.17 180) (layer "B.SilkS") (hide yes) - (uuid "29f569ca-8997-4790-89a9-5c670cb77ef6") + (uuid "456ecacb-6861-4150-a2be-34cf9f63c832") (effects (font (size 1 1) @@ -24456,10 +24385,10 @@ (justify mirror) ) ) - (property "Value" "10µF" - (at 0 -1.43 0) + (property "Value" "10kΩ" + (at 0 -1.17 180) (layer "B.Fab") - (uuid "0c37499e-eeea-411d-837b-b1b106396141") + (uuid "1b38bcb2-b9f0-4354-bfc1-2e14c19c2f09") (effects (font (size 1 1) @@ -24469,10 +24398,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "31e3334d-3e8f-45a8-823b-e18db62e6f35") + (uuid "bb0d5721-aa25-45c7-b06c-795a883794a8") (effects (font (size 1.27 1.27) @@ -24480,11 +24409,11 @@ (justify mirror) ) ) - (property "Description" "Unpolarized capacitor" - (at 0 0 0) + (property "Description" "Resistor" + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "731eb54d-62ef-4612-8882-99555f6fb3e6") + (uuid "688fca96-0a4a-4897-838d-de6aa5307509") (effects (font (size 1.27 1.27) @@ -24492,12 +24421,12 @@ (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" + (property "MF" "UNI-ROYAL(Uniroyal Elec)" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "5cf3f603-bf5d-493d-8542-22e814607d90") + (uuid "770d71d3-f3b5-4e41-a939-736593463f65") (effects (font (size 1 1) @@ -24506,12 +24435,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL10A106KP8NNNC" + (property "Manufacturer_Part_Number" "0402WGF1002TCE" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "da606c56-37e7-4acc-9b07-336c3beab960") + (uuid "158073f6-be48-475e-b753-2a8e4cc57a65") (effects (font (size 1 1) @@ -24520,12 +24449,12 @@ (justify mirror) ) ) - (property "LCSC" "C19702" + (property "LCSC" "C25744" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "96c5e9e9-0c61-4baa-bb7e-98c929770dc4") + (uuid "5b2c2c91-8219-42f2-8638-637715eda273") (effects (font (size 1 1) @@ -24534,34 +24463,32 @@ (justify mirror) ) ) - (property "Stackup Path" "C_3V3_1" - (at -2 0 270) + (property "Stackup Path" "R_STAT1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "073aac27-27c6-47bb-a3ba-7fad83cb148b") + (uuid "1d3aadb7-20bf-4d44-8bec-4f505b958fba") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:21" - (at -2 0 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:69" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "1057e9d5-e6d1-4be5-b02e-25d32c274185") + (uuid "ff1ab658-35f9-492c-874b-ad98eb93b05a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "C_*") - (path "/b4d4419c-0878-52d2-974a-2ccc35b2ca95") + (property ki_fp_filters "R_*") + (path "/49093ee7-a404-5ac1-b4ee-14373f94d3cb") (units (unit (name "A") @@ -24571,79 +24498,79 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.14058 -0.51) - (end 0.14058 -0.51) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "58efd5af-4061-4746-a119-98c37d69ecca") + (uuid "0498793a-72c5-44f1-8bd3-d409e0f1d659") ) (fp_line - (start -0.14058 0.51) - (end 0.14058 0.51) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "7fe2c87e-beed-4403-a001-3c170a7b804a") + (uuid "37155dc7-71df-4640-b961-fafa91ecfc48") ) (fp_rect - (start -1.48 0.73) - (end 1.48 -0.73) + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "B.CrtYd") - (uuid "a2117227-d851-46df-aaf9-d0c3c0bc9647") + (uuid "86976913-e161-491d-bcee-12b0d350c357") ) (fp_rect - (start -0.8 0.4) - (end 0.8 -0.4) + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "1df0fc4c-36be-40d6-918a-4cc50e2e48d6") + (uuid "3945b37c-6b7c-4570-80f3-841d644b7d70") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") - (uuid "d9f791a3-4207-4fa7-b561-99cb0982dec3") + (uuid "16d49a3b-4437-450b-ad40-77d62cf9c08b") (effects (font - (size 0.4 0.4) - (thickness 0.06) + (size 0.26 0.26) + (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -0.775 0) - (size 0.9 0.95) + (at -0.51 0 180) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") + (net "/MCU_Core/STAT1") (pintype "passive") - (uuid "ddb259fd-1ab8-4fd4-b8bf-a9bb6dcfac21") + (uuid "f0ef7273-1499-4d67-b1f1-7ca063c1a475") ) (pad "2" smd roundrect - (at 0.775 0) - (size 0.9 0.95) + (at 0.51 0 180) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "GND") + (net "3V3") (pintype "passive") - (uuid "5f3f9d5f-9576-4fab-9431-67d5fb32df74") + (uuid "abdcac3e-8c2e-4643-9268-4b5673b73cf9") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_0603_1608Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -24656,17 +24583,16 @@ ) ) (footprint "Resistor_SMD:R_0402_1005Metric" - (placed yes) (layer "B.Cu") - (uuid "cfa4e7e5-e902-43d0-b905-c5edd76d51e2") - (at 133.775 91.615) + (uuid "bdb71cfa-e4dd-4942-9c65-01570ccf25a6") + (at 121.79 98.25 180) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_VSYS1" + (property "Reference" "R_ISET1" (at 0 1.17 180) (layer "B.SilkS") (hide yes) - (uuid "13167c5f-b335-4025-a75d-d64d8ce9f4d0") + (uuid "5e6088dd-9c33-4bc3-8eee-c89cd0f94065") (effects (font (size 1 1) @@ -24675,10 +24601,10 @@ (justify mirror) ) ) - (property "Value" "200kΩ" + (property "Value" "604Ω" (at 0 -1.17 180) (layer "B.Fab") - (uuid "da3007ab-1c39-4b82-9e4d-63c8490b728b") + (uuid "f027cebe-49d5-49e6-a92f-4d7877f2f125") (effects (font (size 1 1) @@ -24691,7 +24617,7 @@ (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "21bea923-03d4-426b-becf-b0373e3738f8") + (uuid "56adb090-8388-438a-8aa5-a7a90520d4a6") (effects (font (size 1.27 1.27) @@ -24703,7 +24629,7 @@ (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "f994e644-c2e6-4017-82d7-6243236cce15") + (uuid "1ab6c9c1-0651-4b8a-b292-2191d1c40c23") (effects (font (size 1.27 1.27) @@ -24711,12 +24637,12 @@ (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (property "MF" "Yageo" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "54f7ff02-74f7-4c81-afb8-b3af2942bc9b") + (uuid "93dd57e3-770b-42aa-be24-b8ff6a89ee2c") (effects (font (size 1 1) @@ -24725,12 +24651,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF2003TCE" + (property "Manufacturer_Part_Number" "AC0402FR-07604RL" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "21155c86-0810-4b70-9d92-def481c0bf08") + (uuid "c5f42212-90cd-48ed-aa3a-520473a4aad6") (effects (font (size 1 1) @@ -24739,12 +24665,12 @@ (justify mirror) ) ) - (property "LCSC" "C25764" + (property "LCSC" "C227167" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "78d395ea-2188-4ef7-9098-ca0bc8bea8e6") + (uuid "5c14eb78-297f-4dbb-9b25-0673f1b19edb") (effects (font (size 1 1) @@ -24753,34 +24679,32 @@ (justify mirror) ) ) - (property "Stackup Path" "R_VSYS1" + (property "Stackup Path" "R_ISET1" (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "2e98c534-3a48-4114-80b8-f694da45a663") + (uuid "e0499828-6650-443b-bf0f-547b948b76aa") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:70" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:65" (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "bd9ed807-d5c8-4d99-841e-f600d0fb2dd0") + (uuid "1983bfb0-9674-410c-8bbd-b464c2145847") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) (property ki_fp_filters "R_*") - (path "/3a5f22cb-80f5-5db2-96cc-fadabb0102ec") + (path "/2fe72eb7-3d6a-5c32-af62-a1e01e62a952") (units (unit (name "A") @@ -24790,24 +24714,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "3dd8c954-aaff-41de-bc7e-dfc7b8b02f81") + (uuid "23bb6bad-11f5-411f-ab80-70247bd3017e") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "b4bc846b-b386-417e-ad40-324dceca41e1") + (uuid "c52fb6f1-a4af-41a8-9301-e057c59d8518") ) (fp_rect (start -0.93 0.47) @@ -24818,7 +24742,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "b53578ed-630f-4302-9a54-72698c6571ab") + (uuid "2c117a4d-e0b3-4c82-b11b-3c1d5965bf1b") ) (fp_rect (start -0.525 0.27) @@ -24829,12 +24753,12 @@ ) (fill no) (layer "B.Fab") - (uuid "23f2b046-0d47-4e71-98c8-84ecca04a855") + (uuid "b35989b2-e151-4d5d-a2f1-819bb5613383") ) (fp_text user "${REFERENCE}" (at 0 0 180) (layer "B.Fab") - (uuid "90ebf47f-4733-4bcf-b6f1-11e75f4862ee") + (uuid "6821b019-6c3a-42ba-8035-e3c683d3a27e") (effects (font (size 0.26 0.26) @@ -24844,22 +24768,22 @@ ) ) (pad "1" smd roundrect - (at -0.51 0) + (at -0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "VSYS") + (net "/Power_Charger/CHG_ISET") (pintype "passive") - (uuid "f6449fe1-0879-4f27-a9df-9cf6e30e52d5") + (uuid "0e57cbae-1176-4079-835c-c089cc4ef2cb") ) (pad "2" smd roundrect - (at 0.51 0) + (at 0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/VSYS_SENSE") + (net "GND") (pintype "passive") - (uuid "f3d8872a-314d-4e33-90a1-1412a546e363") + (uuid "d76c8050-af3e-4bf0-a359-2060ec100e76") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -24874,17 +24798,17 @@ ) ) ) - (footprint "C_1206_3216Metric" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "d19167e0-90ba-4be4-995b-680d17fccab0") - (at 146.495 95.395 90) - (descr "Capacitor SMD 1206 (3216 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "capacitor") - (property "Reference" "C_RF_BULK1" - (at 0 1.85 270) + (uuid "c76f16eb-c754-4fa8-a812-bda93b6b357c") + (at 130.775 123.815) + (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") + (tags "resistor") + (property "Reference" "R_CC1" + (at 0 1.17 0) (layer "B.SilkS") (hide yes) - (uuid "d5b35823-dadc-4ec8-9a8a-d8b66a93d14b") + (uuid "9d2ee31c-7e2a-4731-9d51-901bba8c2132") (effects (font (size 1 1) @@ -24893,10 +24817,10 @@ (justify mirror) ) ) - (property "Value" "47µF" - (at 0 -1.85 270) + (property "Value" "5.1kΩ" + (at 0 -1.17 0) (layer "B.Fab") - (uuid "b8cc4119-e36a-4b1b-ab00-84ed8d94c7c6") + (uuid "073dee7c-4415-4a5d-90a5-95dd74494753") (effects (font (size 1 1) @@ -24906,10 +24830,10 @@ ) ) (property "Datasheet" "" - (at 0 0 270) + (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "be9bd159-a2a1-4848-bf51-83da0dcc286f") + (uuid "e02f30a1-0820-4767-b493-3c9c937a839e") (effects (font (size 1.27 1.27) @@ -24917,11 +24841,11 @@ (justify mirror) ) ) - (property "Description" "" - (at 0 0 270) + (property "Description" "Resistor" + (at 0 0 0) (layer "B.Fab") (hide yes) - (uuid "1ad789d1-d6db-4ae3-95b2-8790fefc49e2") + (uuid "dd5ccccd-33da-45ec-974e-22f870e0db44") (effects (font (size 1.27 1.27) @@ -24929,11 +24853,12 @@ (justify mirror) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 270) - (layer "B.SilkS") + (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "ce21c047-22c3-42d5-b9ed-344485c9fa51") + (uuid "5c60373e-ab8d-40c4-a710-aa15146ef450") (effects (font (size 1 1) @@ -24942,37 +24867,39 @@ (justify mirror) ) ) - (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 270) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "0402WGF5101TCE" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "8fb21690-0a39-49bb-b832-6da7ca629085") + (uuid "b8435940-db2a-4fe2-95be-ccd8d1961e9d") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "CL31A476MPHNNNE" - (at 0 -2 270) - (layer "B.SilkS") + (property "LCSC" "C25905" + (at 0 0 180) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "e6856263-00eb-4eda-89f2-4257c81def05") + (uuid "28d4cce8-c77c-48b3-913c-9c9df549d685") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C96123" - (at 0 -2 270) + (property "Stackup Path" "R_CC1" + (at 2 0 90) (layer "B.SilkS") (hide yes) - (uuid "4dfa8d81-2609-4a50-b89f-07d896d698a3") + (uuid "619ef3d5-45d7-4c73-a5e0-23ba0e944c3c") (effects (font (size 1.27 1.27) @@ -24981,11 +24908,11 @@ (justify mirror) ) ) - (property "Stackup Path" "C_RF_BULK1" - (at 0 -2 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:57" + (at 2 0 90) (layer "B.SilkS") (hide yes) - (uuid "63b82343-f0a5-4cdf-b3f0-f3c591114071") + (uuid "66337094-c578-49a4-a89f-87fb26533af6") (effects (font (size 1.27 1.27) @@ -24994,94 +24921,90 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:94" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "6b3e513f-4b68-4739-b19e-c2473dcf7610") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (property ki_fp_filters "R_*") + (path "/ed5d7f5c-8fa0-5dc7-9d3e-fe8638f144ed") + (units + (unit + (name "A") + (pins "1" "2") ) ) - (path "/77121da6-372d-5e42-a164-9e10582877a3") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.711252 -0.91) - (end 0.711252 -0.91) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "452365fb-4155-4e92-ba14-a4b330d4953a") + (uuid "01570a01-fa34-4f59-9ced-c8f6a242dbf8") ) (fp_line - (start -0.711252 0.91) - (end 0.711252 0.91) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "079491d4-9a61-4ad1-8485-c70ec162ce14") + (uuid "07974829-4925-4e43-b8d1-1ba1e0d6e749") ) (fp_rect - (start -2.3 1.15) - (end 2.3 -1.15) + (start -0.93 0.47) + (end 0.93 -0.47) (stroke (width 0.05) (type solid) ) (fill no) (layer "B.CrtYd") - (uuid "e677d0f0-db11-4bdb-b312-1f8d148f806d") + (uuid "f69587d1-53d6-4da9-99c6-28b54df59b38") ) (fp_rect - (start -1.6 0.8) - (end 1.6 -0.8) + (start -0.525 0.27) + (end 0.525 -0.27) (stroke (width 0.1) (type solid) ) (fill no) (layer "B.Fab") - (uuid "68e6d401-cdcf-4b41-bf7f-f592c7c2486a") + (uuid "7fd33140-3e83-44ec-b1a6-c118d3c14db4") ) (fp_text user "${REFERENCE}" - (at 0 0 270) + (at 0 0 0) (layer "B.Fab") - (uuid "a5347b7c-8156-4166-a42f-6d512be8ea7a") + (uuid "0f59184e-bd23-4a4c-941b-bd9c3f1ed4cf") (effects (font - (size 0.8 0.8) - (thickness 0.12) + (size 0.26 0.26) + (thickness 0.04) ) (justify mirror) ) ) (pad "1" smd roundrect - (at -1.475 0 90) - (size 1.15 1.8) + (at -0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.217391) - (net "/MCU_Core/3V3_RF") - (uuid "f78f4f91-3ada-488b-b2d3-47f28148ca4c") + (roundrect_rratio 0.25) + (net "/USB_C/USB_CC1") + (pintype "passive") + (uuid "d8d01e7e-29c5-4c2a-aede-7bb8ae77a4fb") ) (pad "2" smd roundrect - (at 1.475 0 90) - (size 1.15 1.8) + (at 0.51 0) + (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.217391) + (roundrect_rratio 0.25) (net "GND") - (uuid "5b04c40c-0ab1-48cc-910e-456d7b253ee9") + (pintype "passive") + (uuid "0d0ace54-f86e-43bb-8e5e-6c99f498f9e3") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Capacitor_SMD.3dshapes/C_1206_3216Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" (offset (xyz 0 0 0) ) @@ -25093,17 +25016,17 @@ ) ) ) - (footprint "R_0402_1005Metric" + (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "d346f618-f69f-4027-8b04-258984dccb4a") - (at 125.875 102.5 90) + (uuid "c92b6f9f-9044-4da5-bd6e-fe98134d0be4") + (at 138.525 99 90) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_I2C_SDA1" + (property "Reference" "R_FB1" (at 0 1.17 270) (layer "B.SilkS") (hide yes) - (uuid "738fc9b4-4996-4ea5-8ec0-1ce90b895bb5") + (uuid "aa331657-6526-4ab1-9f57-21a9badb2692") (effects (font (size 1 1) @@ -25112,10 +25035,10 @@ (justify mirror) ) ) - (property "Value" "4.7kΩ" + (property "Value" "255kΩ" (at 0 -1.17 270) (layer "B.Fab") - (uuid "d91538c1-d581-494b-beb1-8b0c257178f0") + (uuid "1238173b-a4f4-4f58-b3ac-c3d2f5c548fe") (effects (font (size 1 1) @@ -25128,7 +25051,7 @@ (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "b9d928ce-7af4-447c-91a2-3edc0aecaeb4") + (uuid "f11cec6a-58c2-4975-90f3-bbc35a490baf") (effects (font (size 1.27 1.27) @@ -25136,11 +25059,11 @@ (justify mirror) ) ) - (property "Description" "" + (property "Description" "Resistor" (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "53468e53-1f79-428c-a37a-036a1e88f2c8") + (uuid "6c7284d5-72ce-4b45-945a-c742fb732ae1") (effects (font (size 1.27 1.27) @@ -25148,11 +25071,12 @@ (justify mirror) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 270) - (layer "B.SilkS") + (property "MF" "Yageo" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "4d89aa3c-0a29-44cb-867f-b30bb7224e7c") + (uuid "f69fa09e-a605-46ff-9957-86c9c379c29b") (effects (font (size 1 1) @@ -25161,72 +25085,66 @@ (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 -2 270) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "RC0402FR-07255KL" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "f680fe11-502a-4225-9fc7-5d52ede6fa08") + (uuid "76b2cd8c-7511-4011-b965-72c570f32567") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF4701TCE" - (at 0 -2 270) - (layer "B.SilkS") + (property "LCSC" "C327361" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "e865c2d4-cc91-4fdc-9ed6-a0ce20beb711") + (uuid "5d99b27d-692b-46c3-bd3f-f6e86402ecf1") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C25900" - (at 0 -2 270) + (property "Stackup Path" "R_FB1" + (at -2 0 180) (layer "B.SilkS") (hide yes) - (uuid "564aa6eb-b819-4616-a2c6-d4b16bdbd9be") + (uuid "6707385a-0a74-4cb9-9543-6d4884fee472") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Path" "R_I2C_SDA1" - (at 0 -2 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:60" + (at -2 0 180) (layer "B.SilkS") (hide yes) - (uuid "a7a82439-3804-42e7-ac54-6abc6a2cc15f") + (uuid "93ef101b-d7ab-44a2-8ef0-994b36a8d15f") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:99" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "1b57620b-1182-4682-bb22-eb5a5bbedaab") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (property ki_fp_filters "R_*") + (path "/56d198ab-e2b1-526a-ada9-1e646d15ad03") + (units + (unit + (name "A") + (pins "1" "2") ) ) - (path "/08526ea4-c891-56dc-9aed-02c7f7119ded") (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line @@ -25237,7 +25155,7 @@ (type solid) ) (layer "B.SilkS") - (uuid "2a619a14-6fcc-48d7-9031-878c6eae6a12") + (uuid "0fdb9e0a-7131-4414-9f25-f3c5889305c6") ) (fp_line (start -0.153641 0.38) @@ -25247,7 +25165,7 @@ (type solid) ) (layer "B.SilkS") - (uuid "708d1c81-83cd-42be-8900-db3927c605aa") + (uuid "94a7d12f-a4f3-493d-8c18-10cf9faeef6d") ) (fp_rect (start -0.93 0.47) @@ -25258,7 +25176,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "dd49ac63-9ad3-4339-a866-3de93426f4d6") + (uuid "4453c6d8-06f3-49f7-afce-d3f54ccfaf64") ) (fp_rect (start -0.525 0.27) @@ -25269,12 +25187,12 @@ ) (fill no) (layer "B.Fab") - (uuid "ef378c00-a63a-444e-a521-3652ee47cca7") + (uuid "39215052-6048-4112-abe5-25ed6b09cd83") ) (fp_text user "${REFERENCE}" (at 0 0 270) (layer "B.Fab") - (uuid "115bd838-7786-44fe-886a-3c8b6e547c6e") + (uuid "df404f11-cd7a-4ba1-a2d0-19d956b9d4f9") (effects (font (size 0.26 0.26) @@ -25288,16 +25206,18 @@ (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "3V3") - (uuid "8dccc573-6e90-41b1-8eae-e227cb32e447") + (net "/Power_Buck/BUCK_FB") + (pintype "passive") + (uuid "b473d090-9fc9-4083-9b39-173a9b01b011") ) (pad "2" smd roundrect (at 0.51 0 90) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/Accelerometer/I2C_SDA") - (uuid "427f539e-95aa-448d-a48f-e8c3ec350132") + (net "3V3") + (pintype "passive") + (uuid "45c59866-7bc3-4147-88cf-811128d54c92") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -25312,29 +25232,29 @@ ) ) ) - (footprint "R_0402_1005Metric" + (footprint "XBee_Carrier_Castellated" (layer "B.Cu") - (uuid "d5af9a27-8038-480a-9b9a-cff306f2164c") - (at 125.875 100.25 90) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_I2C_SCL1" - (at 0 1.17 270) + (uuid "d944fcb2-545d-446a-ba99-71d21482f26a") + (at 131.5 112.45 180) + (descr "Hand-solder pads for the Snips XBee 3 carrier, a 22 x 17 mm castellated daughter board that sits flat on this side. 2.54 mm pitch; pads reach 1.7 mm past the carrier for the iron. Keep parts out of the courtyard; vias under the carrier stay tented.") + (tags "XBee castellated daughter board") + (property "Reference" "U_XBEE1" + (at 0 11.5 180) (layer "B.SilkS") (hide yes) - (uuid "4e391954-c621-474b-986f-24f5f3ea79dc") + (uuid "768046a8-0b7e-4e8b-a3ce-b060df7fa621") (effects (font - (size 1 1) - (thickness 0.15) + (size 0.8 0.8) + (thickness 0.12) ) (justify mirror) ) ) - (property "Value" "4.7kΩ" - (at 0 -1.17 270) + (property "Value" "XBee carrier" + (at 0 0 180) (layer "B.Fab") - (uuid "715b2920-c06d-40c8-91ff-51d627a54b58") + (uuid "d222d5c5-930e-4a1c-9e06-bf1eb177ec59") (effects (font (size 1 1) @@ -25344,10 +25264,10 @@ ) ) (property "Datasheet" "" - (at 0 0 270) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "4c241f82-c84d-461b-bf56-833fc4ba9728") + (uuid "c1753de7-ffa1-4960-ba59-f2be25ba6162") (effects (font (size 1.27 1.27) @@ -25356,10 +25276,10 @@ ) ) (property "Description" "" - (at 0 0 270) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "e9d956c7-60d1-4736-a281-e086f2f3c292") + (uuid "158c3ebb-31f1-4bbc-92f2-a67d21d23ed1") (effects (font (size 1.27 1.27) @@ -25367,24 +25287,24 @@ (justify mirror) ) ) - (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 270) + (property "MF" "Snips Controllers" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "d42b7218-dfab-4fb9-a3bc-cf3b2be254ea") + (uuid "c58b7932-ee14-44e9-bf22-b4a2a6ca1821") (effects (font - (size 1 1) + (size 1.27 1.27) (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 -2 270) + (property "Manufacturer_Part_Number" "Snips XBee carrier" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "d23f3e8f-f661-4652-81cc-a36f2a3957c1") + (uuid "3a8b2b56-648e-43e3-9708-06ac9bdddd2c") (effects (font (size 1.27 1.27) @@ -25393,11 +25313,11 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF4701TCE" - (at 0 -2 270) + (property "Stackup Path" "U_XBEE1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "521cc624-3066-44ce-be12-ef0b1ecebcf6") + (uuid "d6fb667a-4a6b-4d14-9d41-34f520ac9917") (effects (font (size 1.27 1.27) @@ -25406,11 +25326,11 @@ (justify mirror) ) ) - (property "LCSC" "C25900" - (at 0 -2 270) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:100" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "b07b3730-dbcd-4794-a8ca-f5f9bc34a66c") + (uuid "1ab3081a-1ea8-4f2e-948e-deccb4293e9c") (effects (font (size 1.27 1.27) @@ -25419,141 +25339,328 @@ (justify mirror) ) ) - (property "Stackup Path" "R_I2C_SCL1" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "96c2dafa-e4bc-44db-8ea3-5f1dad43eb6a") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (path "/39a73dc3-af09-5c61-8628-ae011dd3549c") + (attr smd exclude_from_pos_files exclude_from_bom) + (duplicate_pad_numbers_are_jumpers no) + (fp_line + (start 11.1 8.5) + (end 11.1 -6.9) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "00e9d1b6-4090-4bee-acbc-483b659ba54f") + ) + (fp_line + (start 11.1 -6.9) + (end 6.2 -8.6) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "8032da8e-1f18-47ec-bb5a-205f42a845f0") + ) + (fp_line + (start -11.1 8.5) + (end -11.1 -8.5) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "c7a51d4b-ec68-4251-bf77-574123a332d3") + ) + (fp_line + (start 11.25 8.75) + (end 11.25 -6.9) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "b17fdad0-0013-42b8-93c2-0a15faa60b41") + ) + (fp_line + (start 11.25 -6.9) + (end 6.15 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "e9ca36eb-3dff-49b9-be68-ffb19cd38160") + ) + (fp_line + (start 6.15 10.45) + (end 6.15 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "f5cecb46-4677-4f9a-89a3-6b6809f8f092") + ) + (fp_line + (start 6.15 8.75) + (end 11.25 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "01b79c4e-81eb-4c8d-b7d3-c1b8024cb3e3") + ) + (fp_line + (start 6.15 -8.75) + (end 6.15 -8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "cfe08ae4-4bba-4e2e-82ba-a95d0f17ff06") + ) + (fp_line + (start 6.15 -8.75) + (end 6.15 -10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "a48c5273-eb7d-4d3a-8d71-524a5206cc37") + ) + (fp_line + (start 6.15 -10.45) + (end -8.75 -10.45) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "13684811-ab71-4d77-94c4-da96d9a813c6") + ) + (fp_line + (start -8.75 10.45) + (end 6.15 10.45) + (stroke + (width 0.05) + (type solid) ) + (layer "B.CrtYd") + (uuid "e013bff0-7048-4e02-98c6-dd6d9e3788d4") ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:98" - (at 0 -2 270) - (layer "B.SilkS") - (hide yes) - (uuid "e5c2c5ae-e612-4981-9981-2f5a4ef15865") - (effects - (font - (size 1.27 1.27) - (thickness 0.15) - ) - (justify mirror) + (fp_line + (start -8.75 8.75) + (end -8.75 10.45) + (stroke + (width 0.05) + (type solid) ) + (layer "B.CrtYd") + (uuid "6e3de5cf-c56d-41b0-9df0-3814b28641e4") ) - (path "/5fb0f127-1a56-5891-b4dd-d4ad826bd818") - (attr smd) - (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -8.75 -8.75) + (end -11.25 -8.75) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "f61ffcbd-1f19-4cbf-a642-555eeecea64c") + (layer "B.CrtYd") + (uuid "f7524220-7516-4e3f-8e36-d0ad9209f43d") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -8.75 -10.45) + (end -8.75 -8.75) (stroke - (width 0.12) + (width 0.05) (type solid) ) - (layer "B.SilkS") - (uuid "c02fbc22-41ba-4308-beee-479d6dcb2b5b") + (layer "B.CrtYd") + (uuid "c74fb4fb-ad8c-4449-965b-8afa88965a57") ) - (fp_rect - (start -0.93 0.47) - (end 0.93 -0.47) + (fp_line + (start -11.25 8.75) + (end -8.75 8.75) (stroke (width 0.05) (type solid) ) - (fill no) (layer "B.CrtYd") - (uuid "57a82b97-7942-43b4-8aa1-b86ee24cae6e") + (uuid "32c857c2-339b-404a-8347-4a0927c3d56c") ) - (fp_rect - (start -0.525 0.27) - (end 0.525 -0.27) + (fp_line + (start -11.25 -8.75) + (end -11.25 8.75) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "f5f3548b-7635-4764-b8e9-52b4027ac9cc") + ) + (fp_line + (start 11 8.5) + (end 11 -6.9) (stroke (width 0.1) (type solid) ) - (fill no) (layer "B.Fab") - (uuid "c3436346-6e85-4d25-b411-e108841ba1fb") + (uuid "4e545035-053f-4654-b6c5-ec40d4473d0b") ) - (fp_text user "${REFERENCE}" - (at 0 0 270) + (fp_line + (start 11 -6.9) + (end 6.1 -8.5) + (stroke + (width 0.1) + (type solid) + ) (layer "B.Fab") - (uuid "015cfff7-5697-43f4-afd3-97413febbee5") - (effects - (font - (size 0.26 0.26) - (thickness 0.04) - ) - (justify mirror) + (uuid "3272402f-b39b-4ace-8b72-d106f13f9565") + ) + (fp_line + (start 6.1 -8.5) + (end -11 -8.5) + (stroke + (width 0.1) + (type solid) ) + (layer "B.Fab") + (uuid "3dd09c07-b4be-476f-b003-9164efeb729d") ) - (pad "1" smd roundrect - (at -0.51 0 90) - (size 0.54 0.64) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) + (fp_line + (start -11 8.5) + (end 11 8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "7eaed27d-6bc5-463e-9b42-12626071b66b") + ) + (fp_line + (start -11 -8.5) + (end -11 8.5) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "ddc1f089-1ada-42b2-b59a-5e332299c7d7") + ) + (pad "1" smd rect + (at 5.05 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_CTS") + (uuid "5b2ff289-a1bf-4309-8dd1-56d56d1f4b48") + ) + (pad "2" smd rect + (at 2.51 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_DIN") + (uuid "88f63b36-e94f-4cf6-a5e0-0f9fcfaa0648") + ) + (pad "3" smd rect + (at -0.03 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_DOUT") + (uuid "37d79c5a-fff4-4cb2-808e-0ec85e1abf5d") + ) + (pad "4" smd rect + (at -2.57 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_RTS") + (uuid "7836734f-37fb-4cde-94bb-a1b6e3a593c6") + ) + (pad "5" smd rect + (at -5.11 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "80af511f-bc15-4112-8ef6-e5bf15b31899") + ) + (pad "6" smd rect + (at -7.65 -8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_RESET") + (uuid "187f0fdc-a8b2-4de5-90ca-ce9e8d6b0b27") + ) + (pad "7" smd rect + (at -7.65 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "21398a15-5672-41da-97ef-6db5f16fa4bd") + ) + (pad "8" smd rect + (at -5.11 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "GND") + (uuid "f42af129-68cd-466b-8df4-f0e799e2a15f") + ) + (pad "9" smd rect + (at -2.57 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") (net "3V3") - (uuid "f749124c-52bf-4a7f-9d14-9ea730d0b5f5") + (uuid "c3f6f707-709a-4734-b177-68ee396265c7") ) - (pad "2" smd roundrect - (at 0.51 0 90) - (size 0.54 0.64) - (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "/Accelerometer/I2C_SCL") - (uuid "cc52da01-6d7a-4deb-94a4-80ac385aaec6") + (pad "10" smd rect + (at -0.03 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "3V3") + (uuid "5e3749b8-982b-457f-8528-a14c693cc41b") ) - (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" - (offset - (xyz 0 0 0) - ) - (scale - (xyz 1 1 1) - ) - (rotate - (xyz 0 0 0) - ) + (pad "11" smd rect + (at 2.51 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "GND") + (uuid "ad8c048c-30ca-4e51-b72b-dc85a75ae9e6") ) + (pad "12" smd rect + (at 5.05 8.85 180) + (size 1.7 2.7) + (layers "B.Cu" "B.Mask") + (net "GND") + (uuid "414bb0d6-9836-4129-a464-68e1634a3516") + ) + (embedded_fonts no) ) - (footprint "SW_Alps_SKRP" + (footprint "Package_TO_SOT_SMD:SOT-23-5" (layer "B.Cu") - (uuid "d85189cb-feaf-4f8e-861f-6a2301bbbe31") - (at 146.175 101.775) - (descr "Alps SKRP 4.2x3.2x2.5mm tact switch, 4 pads. Land from the Alps SKRP datasheet (PC board land dimensions): 5.2/3.1 x 2.8/1.5 mm. Terminals 1-2 and 3-4 are joined inside, so pad 1 is the top pair and pad 2 the bottom pair. 3D model is the same-size C&K PTS810.") - (tags "SPST Button Switch") - (property "Reference" "SW_RST1" - (at 0.005 -2.475 0) + (uuid "d9b04e33-9e45-4080-992f-47fe8473b9f2") + (at 147.475 94.6125 90) + (descr "SOT, 5 Pin (JEDEC MO-178 Var AA https://www.jedec.org/document_search?search_api_views_fulltext=MO-178)") + (tags "SOT TO_SOT_SMD") + (property "Reference" "U_BUCK1" + (at 0 2.4 270) (layer "B.SilkS") (hide yes) - (uuid "aeaf01cc-943e-4249-8141-2be4dbc9cf52") + (uuid "06c5b817-939d-44a9-b139-7612a9bfda93") (effects (font - (size 0.8 0.8) - (thickness 0.12) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (property "Value" "SKRPABE010" - (at 0 -2.6 0) + (property "Value" "TLV62569DBVR" + (at 0 -2.4 270) (layer "B.Fab") - (uuid "db0aaf92-101f-41a1-8f08-b0eaddd35c31") + (uuid "6ea73f51-d66e-44b8-aea0-813ad0f36c8c") (effects (font (size 1 1) @@ -25562,346 +25669,424 @@ (justify mirror) ) ) - (property "Datasheet" "" - (at 0 0 180) - (unlocked yes) + (property "Datasheet" "http://www.ti.com/lit/ds/symlink/tlv62569.pdf" + (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "8a3d4dd2-fbdb-419e-b0e1-de26bb547d39") + (uuid "7fb1d309-4b2c-4a78-baa9-daa8d50db52d") (effects (font (size 1.27 1.27) - (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "" - (at 0 0 180) - (unlocked yes) + (property "Description" "High Efficiency Synchronous Buck Converter, Adjustable Output 0.6V-5.5V, 2A, SOT-23-5" + (at 0 0 270) (layer "B.Fab") (hide yes) - (uuid "60bc2a21-150a-400c-ad72-0de1978da436") + (uuid "35ac9952-dde7-4311-8a9a-7200d9a7897e") (effects (font (size 1.27 1.27) - (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "Alps Alpine" - (at 0 -2 0) - (layer "B.SilkS") + (property "MF" "Texas Instruments" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "088b4cae-7b0c-490d-9063-264b52a9e288") + (uuid "816497c5-1865-4ff9-9a65-7ba6842f37ac") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Manufacturer_Part_Number" "SKRPABE010" - (at 0 -2 0) - (layer "B.SilkS") + (property "Manufacturer_Part_Number" "TLV62569DBVR" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "c0bad590-3f9b-4333-a7dc-03790658da28") + (uuid "bafc3ee0-4692-4a10-9e92-fecba59e9073") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "LCSC" "C115360" - (at 0 -2 0) - (layer "B.SilkS") + (property "LCSC" "C141836" + (at 0 0 90) + (unlocked yes) + (layer "B.Fab") (hide yes) - (uuid "afb1420c-538d-4c62-96ba-6e23cfcff9f4") + (uuid "29de6419-cfee-4931-9e9c-bb14f8038d1b") (effects (font - (size 1.27 1.27) + (size 1 1) (thickness 0.15) ) (justify mirror) ) ) - (property "Stackup Path" "SW_RST1" - (at 0 -2 0) + (property "Stackup Path" "U_BUCK1" + (at -2 0 180) (layer "B.SilkS") (hide yes) - (uuid "e2207790-2c61-47e9-8bd4-394f9ea8c5cd") + (uuid "179288aa-34c9-454d-b544-4b635438b2bd") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:74" - (at 0 -2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:90" + (at -2 0 180) (layer "B.SilkS") (hide yes) - (uuid "65cc920b-f11d-4984-99b6-095566d9de9c") + (uuid "22e59454-0b5c-4792-a7ae-969b2cdbdeac") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (path "/7013cdc7-fa80-5a98-9804-499677cdf3ae") + (property ki_fp_filters "SOT?23*") + (path "/01d79e8b-400a-500d-9fe6-5614a79d1279") + (units + (unit + (name "A") + (pins "4" "1" "2" "3" "5") + ) + ) (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -2.2 -1.7) - (end 2.2 -1.7) + (start 0.91 -1.56) + (end -0.91 -1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "0086d519-b003-4e36-9838-7e10b07f2b2b") + (uuid "d9f6cb6b-5e14-4d8f-be5e-db2ed32cff38") ) (fp_line - (start -2.2 -1.58) - (end -2.2 -1.7) + (start -0.91 -1.56) + (end -0.91 -1.51) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "4a37ea39-aff8-447e-b64b-80a3315ef74c") + (uuid "a8eb601e-f693-421a-9109-73d5215fa174") ) (fp_line - (start -2.2 0.57) - (end -2.2 -0.57) + (start 0.91 -1.51) + (end 0.91 -1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "e5bc120d-33ae-475f-bfa0-4e9b44675667") + (uuid "f01ec1f0-4c70-4a4e-a9d3-f66669c200e1") ) (fp_line - (start -2.2 1.7) - (end -2.2 1.58) + (start 0.91 0.39) + (end 0.91 -0.39) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "07f81fca-9268-47af-9902-0f78351cfb07") + (uuid "f697edec-c77d-4821-9063-5ddb6e869bac") ) (fp_line - (start 2.2 -1.7) - (end 2.2 -1.58) + (start -0.91 1.51) + (end -0.91 1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "aed82008-14d2-4579-8789-0283df0b7275") + (uuid "21cfb23b-5952-41bb-b266-41578fda7896") ) (fp_line - (start 2.2 -0.57) - (end 2.2 0.57) + (start 0.91 1.56) + (end 0.91 1.51) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "23b1bfc3-82ca-4265-bd66-ca7da434bb21") + (uuid "7c4f4d0e-1f7c-4142-b9a8-664c1087836a") ) (fp_line - (start 2.2 1.58) - (end 2.2 1.7) + (start -0.91 1.56) + (end 0.91 1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "91040cc9-5755-4f04-83fd-ff3b7c028f18") + (uuid "545707ed-7e63-478f-8323-a1a36b113720") ) - (fp_line - (start 2.2 1.7) - (end -2.2 1.7) + (fp_poly + (pts + (xy -1.45 1.51) (xy -1.69 1.84) (xy -1.21 1.84) + ) (stroke (width 0.12) (type solid) ) + (fill yes) (layer "B.SilkS") - (uuid "88ae15ae-fbbb-4e52-99b4-4006caa338a1") + (uuid "f45cad6c-88d6-448f-a8cd-eb481071c53b") ) (fp_line - (start -2.85 -1.85) - (end -2.85 1.85) + (start 1.05 -1.7) + (end -1.05 -1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "3d93d078-8625-4d60-bf6e-f9a8a3629e16") + (uuid "cdb35ff1-cfa5-46c7-86a4-1d3105affd9e") ) (fp_line - (start -2.85 1.85) - (end 2.85 1.85) + (start -1.05 -1.7) + (end -1.05 -1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "356175b2-59f6-4cc5-8e80-27efe7c359de") + (uuid "7d6ab570-d873-4f8f-b996-2265b74af962") ) (fp_line - (start 2.85 -1.85) - (end -2.85 -1.85) + (start 2.05 -1.5) + (end 1.05 -1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "0a602143-754b-44e1-b34d-d376046ebccc") + (uuid "a2225891-6b43-4d0e-8b56-52911ca9c8a3") ) (fp_line - (start 2.85 1.85) - (end 2.85 -1.85) + (start 1.05 -1.5) + (end 1.05 -1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "5f1bf4c3-35da-4822-ae74-baf65a0feb5a") + (uuid "ae54ad69-dd53-4f0d-8e57-1a6f53f6ffd9") ) (fp_line - (start -2.1 -1.6) - (end 2.1 -1.6) + (start -1.05 -1.5) + (end -2.05 -1.5) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "0b0783d4-b822-42e6-a10a-08bfe5bbfdf2") + (layer "B.CrtYd") + (uuid "4fc87d0e-2edc-48ba-ad1d-27a195e84c7c") ) (fp_line - (start -2.1 1.6) - (end -2.1 -1.6) + (start -2.05 -1.5) + (end -2.05 1.5) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "efec3883-1178-4284-95b6-e869ee95f62d") + (layer "B.CrtYd") + (uuid "4448f008-8002-44d8-9671-f6efe3e6805c") ) (fp_line - (start -0.4 1.1) - (end 0.4 1.1) + (start 2.05 -0.39) + (end 2.05 -1.5) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "0238cbb6-3d77-4fa9-a491-afe39cb3fc8a") + (layer "B.CrtYd") + (uuid "742fc6a7-c222-4cac-9c70-61f6ff131381") ) (fp_line - (start 0.4 -1.1) - (end -0.4 -1.1) + (start 1.05 -0.39) + (end 2.05 -0.39) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "1f3c9317-210b-408d-8074-6884adac9154") + (layer "B.CrtYd") + (uuid "438d8665-9576-42c2-b4ca-1527d72d59dd") ) (fp_line - (start 2.1 -1.6) - (end 2.1 1.6) + (start 2.05 0.39) + (end 1.05 0.39) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "745d7c4e-fa82-43d3-a162-2db7d1a073dd") + (layer "B.CrtYd") + (uuid "a14d3599-168d-4808-aa74-618c2c3b1e06") ) (fp_line - (start 2.1 1.6) - (end -2.1 1.6) + (start 1.05 0.39) + (end 1.05 -0.39) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "67c8cc90-271d-4cd3-b284-7cefdd556970") + (layer "B.CrtYd") + (uuid "70c82a79-83a1-4fa2-a4cf-1083e6f17c77") ) - (fp_arc - (start -0.4 1.1) - (mid -1.5 0) - (end -0.4 -1.1) + (fp_line + (start 2.05 1.5) + (end 2.05 0.39) (stroke - (width 0.1) + (width 0.05) (type solid) ) - (layer "B.Fab") - (uuid "176ae536-3ffd-4ff3-80ad-8a28e5ba5d96") + (layer "B.CrtYd") + (uuid "e971f5cd-fdfe-429e-82d5-cd6082c9f504") ) - (fp_arc - (start 0.4 -1.1) - (mid 1.5 0) - (end 0.4 1.1) + (fp_line + (start 1.05 1.5) + (end 2.05 1.5) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "8d75752a-aa56-48c1-8959-e46244698f27") + ) + (fp_line + (start -1.05 1.5) + (end -1.05 1.7) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "6dac7f2c-0c58-49d8-9817-8a67a6c6c99b") + ) + (fp_line + (start -2.05 1.5) + (end -1.05 1.5) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "75c62025-f1b5-45ec-9f2d-c982aa7758a5") + ) + (fp_line + (start 1.05 1.7) + (end 1.05 1.5) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "a0e4cab1-d62e-4437-85d4-25dc0debe539") + ) + (fp_line + (start -1.05 1.7) + (end 1.05 1.7) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "7ab74d95-192a-426c-a1b4-a2e7ec6ec1dd") + ) + (fp_poly + (pts + (xy -0.4 1.45) (xy 0.8 1.45) (xy 0.8 -1.45) (xy -0.8 -1.45) (xy -0.8 1.05) + ) (stroke (width 0.1) (type solid) ) + (fill no) (layer "B.Fab") - (uuid "4dd1d180-e833-4f81-a814-25f99e381d2b") + (uuid "dbcd7dcd-61fb-4a3f-91cf-ee82a5859a1d") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") - (uuid "3326fd40-d96c-4ad0-ba50-a499b295b003") + (uuid "fa1f1f86-c023-43b4-aff7-33a022afacc1") (effects (font - (size 0.6 0.6) - (thickness 0.09) + (size 0.72 0.72) + (thickness 0.11) ) (justify mirror) ) ) - (pad "1" smd rect - (at -2.075 1.075) - (size 1.05 0.65) + (pad "1" smd roundrect + (at -1.1375 0.95 90) + (size 1.325 0.6) (layers "B.Cu" "B.Mask" "B.Paste") - (net "GND") - (uuid "53ccb2b0-ac2d-4279-bd2b-acb2de2ceee8") + (roundrect_rratio 0.25) + (net "/Power_Buck/PWR_EN") + (pinfunction "EN_1") + (pintype "input") + (uuid "e7db6b0a-2f2f-4c95-b948-f5c1e980c81b") ) - (pad "1" smd rect - (at 2.075 1.075) - (size 1.05 0.65) + (pad "2" smd roundrect + (at -1.1375 0 90) + (size 1.325 0.6) (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) (net "GND") - (uuid "29675819-beb9-4e79-ad75-721032371efb") + (pinfunction "GND_2") + (pintype "power_in") + (uuid "1d1ddd6c-c886-47dc-8b21-6c9ab22afe6a") ) - (pad "2" smd rect - (at -2.075 -1.075) - (size 1.05 0.65) + (pad "3" smd roundrect + (at -1.1375 -0.95 90) + (size 1.325 0.6) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_RESET") - (uuid "9aea8137-62e1-49ef-ae9b-40db20794ddf") + (roundrect_rratio 0.25) + (net "/Power_Buck/BUCK_SW") + (pinfunction "SW_3") + (pintype "power_out") + (uuid "77ad35fb-9199-4834-b179-52252744a8db") ) - (pad "2" smd rect - (at 2.075 -1.075) - (size 1.05 0.65) + (pad "4" smd roundrect + (at 1.1375 -0.95 90) + (size 1.325 0.6) + (layers "B.Cu" "B.Mask" "B.Paste") + (roundrect_rratio 0.25) + (net "VSYS") + (pinfunction "VIN_4") + (pintype "power_in") + (uuid "cb79d23b-cdd4-4a1d-8408-5f624102d898") + ) + (pad "5" smd roundrect + (at 1.1375 0.95 90) + (size 1.325 0.6) (layers "B.Cu" "B.Mask" "B.Paste") - (net "/MCU_Core/MCU_RESET") - (uuid "a0fbb11e-560c-419e-827b-d3e62602ec99") + (roundrect_rratio 0.25) + (net "/Power_Buck/BUCK_FB") + (pinfunction "FB_5") + (pintype "input") + (uuid "d09f2f1d-d4d8-4980-b7b5-bfeb7e545160") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Button_Switch_SMD.3dshapes/SW_SPST_PTS810.step" + (model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-23-5.step" (offset (xyz 0 0 0) ) @@ -25916,11 +26101,11 @@ (footprint "C_0402_1005Metric" (layer "B.Cu") (uuid "dddaf3ed-08e4-48e8-af4b-076f9c3c4fe3") - (at 142.25 69 -90) + (at 127.2 125.9) (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") (property "Reference" "C_IMU_1" - (at 0 1.16 90) + (at 0 1.16 0) (layer "B.SilkS") (hide yes) (uuid "6ce0ff6e-fbca-4274-9530-4564a95276ba") @@ -25933,7 +26118,7 @@ ) ) (property "Value" "100nF" - (at 0 -1.16 90) + (at 0 -1.16 0) (layer "B.Fab") (uuid "f5cca6c0-b3c6-4812-941a-16df63fa27a6") (effects @@ -25945,7 +26130,7 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (hide yes) (uuid "e9cf6831-84fd-42ff-9f20-a29fb6827abc") @@ -25957,7 +26142,7 @@ ) ) (property "Description" "" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (hide yes) (uuid "daee7781-43fb-43ed-bfd5-17ef22dd01ff") @@ -25969,7 +26154,7 @@ ) ) (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 90) + (at 0 0 0) (layer "B.SilkS") (hide yes) (uuid "ac6d5110-0fa6-4092-af90-ef131ecc3eca") @@ -25982,7 +26167,7 @@ ) ) (property "MF" "Samsung Electro-Mechanics" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "245d1b98-f218-46ac-8b77-7d55cd1fb948") @@ -25995,7 +26180,7 @@ ) ) (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "323c43aa-faaa-45a6-b755-24e9ffb5d85c") @@ -26008,7 +26193,7 @@ ) ) (property "LCSC" "C1525" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "cbc0f5c5-b371-44a6-8d79-9697cffd10f0") @@ -26021,7 +26206,7 @@ ) ) (property "Stackup Path" "C_IMU_1" - (at 0 -2 90) + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "aaa722b8-0cd7-4316-9767-e7d877555948") @@ -26033,8 +26218,8 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:27" - (at 0 -2 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:29" + (at 0 -2 0) (layer "B.SilkS") (hide yes) (uuid "0267a58f-b4cb-4e80-bc0c-0bd5e1944bd6") @@ -26050,24 +26235,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "47b88387-8357-45b2-b165-7ae5b2327d05") + (uuid "a2b22e2b-1b57-479c-8648-1f26a5349e7e") ) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "a2b22e2b-1b57-479c-8648-1f26a5349e7e") + (uuid "47b88387-8357-45b2-b165-7ae5b2327d05") ) (fp_rect (start -0.91 0.46) @@ -26092,7 +26277,7 @@ (uuid "0b724235-2b02-469d-9eee-f7e15380ff48") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 0) (layer "B.Fab") (uuid "0bc44f01-7798-4b2f-b0fd-b6addad3a06b") (effects @@ -26104,7 +26289,7 @@ ) ) (pad "1" smd roundrect - (at -0.48 0 270) + (at -0.48 0) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -26112,7 +26297,7 @@ (uuid "9c7de4ce-b6f2-436b-b6d2-aae1f3805b3c") ) (pad "2" smd roundrect - (at 0.48 0 270) + (at 0.48 0) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -26132,18 +26317,17 @@ ) ) ) - (footprint "Resistor_SMD:R_0402_1005Metric" - (placed yes) + (footprint "Inductor_SMD:L_Bourns-SRN4018" (layer "B.Cu") - (uuid "e8959995-a97b-490a-9489-b4f7b64be06d") - (at 136.025 91.615) - (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") - (tags "resistor") - (property "Reference" "R_VSYS2" - (at 0 1.17 0) + (uuid "df90bff6-7d55-4fb3-80be-b1a124878c17") + (at 142.525 95.75 180) + (descr "Bourns SRN4018 series SMD inductor, https://www.bourns.com/docs/Product-Datasheets/SRN4018.pdf") + (tags "Bourns SRN4018 SMD inductor") + (property "Reference" "L_BUCK1" + (at 0 -3.1 180) (layer "B.SilkS") (hide yes) - (uuid "24980e34-12c2-431a-8f1d-a9d96a273e72") + (uuid "ffe59921-017a-4115-ae75-e7362858e013") (effects (font (size 1 1) @@ -26152,10 +26336,10 @@ (justify mirror) ) ) - (property "Value" "100kΩ" - (at 0 -1.17 0) + (property "Value" "2.2µH" + (at 0 3.1 180) (layer "B.Fab") - (uuid "8f6a3e53-fe3b-43a8-b3d4-a2d7621f2e4c") + (uuid "f7ed0b39-2bb6-4ac2-b130-2d4acdfc91d6") (effects (font (size 1 1) @@ -26166,34 +26350,38 @@ ) (property "Datasheet" "" (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "eaf0bbe3-9cfb-4294-b865-7bb5dcbefd5e") + (uuid "3e4322a3-a35b-4e0b-a615-bb32b6a3b4de") (effects (font (size 1.27 1.27) + (thickness 0.15) ) (justify mirror) ) ) - (property "Description" "Resistor" + (property "Description" "Inductor" (at 0 0 0) + (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "7fc006c2-2675-4ae8-a94a-49b703bee878") + (uuid "5fe6f736-15ca-4dab-af95-76963fd8932d") (effects (font (size 1.27 1.27) + (thickness 0.15) ) (justify mirror) ) ) - (property "MF" "UNI-ROYAL(Uniroyal Elec)" + (property "MF" "Bourns" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "49a168d6-6a16-44c6-a545-f8ef17c5daec") + (uuid "b61c9464-b7ff-4ead-994b-2430b0889606") (effects (font (size 1 1) @@ -26202,12 +26390,12 @@ (justify mirror) ) ) - (property "Manufacturer_Part_Number" "0402WGF1003TCE" + (property "Manufacturer_Part_Number" "SRN4018-2R2M" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "3a4332bb-dd49-4d26-b933-0fca5656a7d2") + (uuid "0a5b33bb-be77-48af-818f-8d9552f16b33") (effects (font (size 1 1) @@ -26216,12 +26404,12 @@ (justify mirror) ) ) - (property "LCSC" "C25741" + (property "LCSC" "C913207" (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "52bd1ce5-0fd0-4bf8-b601-ed44e4f002b9") + (uuid "676eb99d-d09a-4889-8cf8-b5da02a85f57") (effects (font (size 1 1) @@ -26230,34 +26418,32 @@ (justify mirror) ) ) - (property "Stackup Path" "R_VSYS2" - (at 0 2 0) + (property "Stackup Path" "L_BUCK1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "5273a233-f6d0-41bd-acab-632e700840b1") + (uuid "d138fa84-f404-44d2-8323-a9765612740a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:71" - (at 0 2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:51" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "c80f382d-f2fc-43fc-bfc9-fc9d1a75d374") + (uuid "09d6870f-54ed-4e4a-a59c-7ba124534793") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property ki_fp_filters "R_*") - (path "/d2b6c4ab-7ef9-5ded-a5d1-4d96c799220d") + (property ki_fp_filters "Choke_* *Coil* Inductor_* L_*") + (path "/6ec4aba0-5ea6-53c2-98e5-0b6074e59f4d") (units (unit (name "A") @@ -26267,79 +26453,197 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start 2.385 2.11) + (end 2.385 1.085) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "ce95fb31-55e2-4591-9bd2-8ae8f6d43a06") + (uuid "4167a84e-1424-4988-bce1-9a930b23a822") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start 2.385 2.11) + (end 1.36 2.11) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "525f7d00-5b79-40fd-900a-9c127f65144b") + (uuid "c90dc85a-046f-4c6f-b35a-c1f6fa814167") ) - (fp_rect - (start -0.93 0.47) - (end 0.93 -0.47) + (fp_line + (start 2.385 -2.11) + (end 2.385 -1.085) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "2e837ce8-8a82-4459-9d15-84c9a79c31e3") + ) + (fp_line + (start 2.385 -2.11) + (end 1.36 -2.11) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "d6f89670-efa9-488c-8215-dd3da07234fe") + ) + (fp_line + (start -2.385 2.11) + (end -1.36 2.11) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "c172ea71-ff50-4d12-b7e5-d3271a6d8b6f") + ) + (fp_line + (start -2.385 2.11) + (end -2.385 1.085) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "000e7df3-b262-457b-b983-b9875b78ae37") + ) + (fp_line + (start -2.385 -2.11) + (end -1.36 -2.11) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "64236419-60f3-4cf7-b820-8960bc28c105") + ) + (fp_line + (start -2.385 -2.11) + (end -2.385 -1.085) + (stroke + (width 0.12) + (type solid) + ) + (layer "B.SilkS") + (uuid "fa1e96ca-d6fc-42cc-a0b4-554c579387e1") + ) + (fp_line + (start 2.53 2.25) + (end 2.53 -2.25) (stroke (width 0.05) (type solid) ) - (fill no) (layer "B.CrtYd") - (uuid "97779d48-9cf1-4da8-af97-9422048a50e0") + (uuid "3415a2c0-31ae-4970-8b32-647dc008fe5e") ) - (fp_rect - (start -0.525 0.27) - (end 0.525 -0.27) + (fp_line + (start -2.53 2.25) + (end 2.53 2.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "eb9a644d-dbd7-4137-ac95-3377b5df40c5") + ) + (fp_line + (start -2.53 2.25) + (end -2.53 -2.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "e45e72e9-9663-4966-a3b0-915b5735dbdf") + ) + (fp_line + (start -2.53 -2.25) + (end 2.53 -2.25) + (stroke + (width 0.05) + (type solid) + ) + (layer "B.CrtYd") + (uuid "5c0ce237-f627-4b79-9010-c4132e503904") + ) + (fp_line + (start 2 2) + (end 2 -2) (stroke (width 0.1) (type solid) ) - (fill no) (layer "B.Fab") - (uuid "33e48ea9-8f9c-41f1-bb69-5ab5ca003079") + (uuid "ba87e1e8-2ad5-4e1d-9bb0-02789d9ff863") + ) + (fp_line + (start 2 -2) + (end -2 -2) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "2b896796-9e14-4e04-851d-d2d2c11795c3") + ) + (fp_line + (start -2 2) + (end 2 2) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "6c67d810-95af-4689-8a4c-dbaeb9db7ce5") + ) + (fp_line + (start -2 2) + (end -2 -2) + (stroke + (width 0.1) + (type solid) + ) + (layer "B.Fab") + (uuid "f3dd3898-1b08-4bd0-9f5e-43cc6b91136f") ) (fp_text user "${REFERENCE}" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") - (uuid "71bb2df3-ddee-4fb1-9819-3e26a316104a") + (uuid "a4c89381-5a1a-41ea-9ea5-7d9485e3ffc9") (effects (font - (size 0.26 0.26) - (thickness 0.04) + (size 1 1) + (thickness 0.15) ) (justify mirror) ) ) - (pad "1" smd roundrect - (at -0.51 0) - (size 0.54 0.64) + (pad "1" smd rect + (at -1.525 0 180) + (size 1.5 3.6) (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "/MCU_Core/VSYS_SENSE") + (net "/Power_Buck/BUCK_SW") + (pinfunction "1_1") (pintype "passive") - (uuid "5340ee3b-7dcb-46b9-8fc3-914353e92958") + (uuid "636579c2-3a8e-4eee-a8cf-ae2dd9018b0d") ) - (pad "2" smd roundrect - (at 0.51 0) - (size 0.54 0.64) + (pad "2" smd rect + (at 1.525 0 180) + (size 1.5 3.6) (layers "B.Cu" "B.Mask" "B.Paste") - (roundrect_rratio 0.25) - (net "GND") + (net "3V3") + (pinfunction "2_2") (pintype "passive") - (uuid "9cbed9b8-2158-4afd-b90d-1503edc590f7") + (uuid "92ef3bbf-544e-448a-b98e-6c61e1cbdb73") ) (embedded_fonts no) - (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" + (model "${KICAD10_3DMODEL_DIR}/Inductor_SMD.3dshapes/L_Bourns-SRN4018.step" (offset (xyz 0 0 0) ) @@ -26354,7 +26658,7 @@ (footprint "Capacitor_SMD:C_0402_1005Metric" (layer "B.Cu") (uuid "ec4e6a9a-e5f5-42b8-becb-1dffc6f774d4") - (at 145.505 76.205 90) + (at 145.505 76.205 -90) (descr "Capacitor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 76, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "capacitor") (property "Reference" "C_STICK1" @@ -26407,7 +26711,7 @@ ) ) (property "MF" "Samsung Electro-Mechanics" - (at 0 0 270) + (at 0 0 90) (unlocked yes) (layer "B.Fab") (hide yes) @@ -26421,7 +26725,7 @@ ) ) (property "Manufacturer_Part_Number" "CL05B104KO5NNNC" - (at 0 0 270) + (at 0 0 90) (unlocked yes) (layer "B.Fab") (hide yes) @@ -26435,7 +26739,7 @@ ) ) (property "LCSC" "C1525" - (at 0 0 270) + (at 0 0 90) (unlocked yes) (layer "B.Fab") (hide yes) @@ -26449,7 +26753,7 @@ ) ) (property "Stackup Path" "C_STICK1" - (at 2 0 180) + (at 2 0 0) (layer "B.SilkS") (hide yes) (uuid "db0bbcbb-dda4-46a4-bfcb-3bd91cfad66f") @@ -26461,8 +26765,8 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:35" - (at 2 0 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:37" + (at 2 0 0) (layer "B.SilkS") (hide yes) (uuid "c17d318b-bedf-40df-b3aa-6698894ee393") @@ -26485,24 +26789,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.107836 -0.36) - (end 0.107836 -0.36) + (start -0.107836 0.36) + (end 0.107836 0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "efcc3cb6-f791-4334-9916-8f8673bbaf18") + (uuid "b10a0718-912e-4951-a1cb-1d1a1f51aa87") ) (fp_line - (start -0.107836 0.36) - (end 0.107836 0.36) + (start -0.107836 -0.36) + (end 0.107836 -0.36) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "b10a0718-912e-4951-a1cb-1d1a1f51aa87") + (uuid "efcc3cb6-f791-4334-9916-8f8673bbaf18") ) (fp_rect (start -0.91 0.46) @@ -26539,16 +26843,16 @@ ) ) (pad "1" smd roundrect - (at -0.48 0 90) + (at -0.48 0 270) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") + (net "3V3") (pintype "passive") (uuid "264cd38c-1f1c-4bde-bd47-1772597f700f") ) (pad "2" smd roundrect - (at 0.48 0 90) + (at 0.48 0 270) (size 0.56 0.62) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -26572,14 +26876,14 @@ (footprint "SOT-23" (layer "B.Cu") (uuid "f05e52b9-3e61-46e0-9483-c13d27a8515f") - (at 128.5625 67) + (at 126.5 64.75 180) (descr "SOT, 3 Pin (JEDEC TO-236 Var AB https://www.jedec.org/document_search?search_api_views_fulltext=TO-236)") (tags "SOT TO_SOT_SMD") (property "Reference" "U_HALL1" - (at 0 2.4 0) + (at 0 2.4 180) (layer "B.SilkS") (hide yes) - (uuid "2ebda393-cf3d-41ea-8d0e-e4db05c1bb4a") + (uuid "4bab6fd3-4458-40be-b509-bbc428677822") (effects (font (size 1 1) @@ -26589,9 +26893,9 @@ ) ) (property "Value" "DRV5055A2QDBZR" - (at 0 -2.4 0) + (at 0 -2.4 180) (layer "B.Fab") - (uuid "f37f5857-25f5-4c70-9067-ee8f344e6171") + (uuid "7f92c423-37d1-4572-9628-c8ce8206b3b9") (effects (font (size 1 1) @@ -26601,10 +26905,10 @@ ) ) (property "Datasheet" "" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "b40c82ee-6ddd-4aab-b801-7589b8799d3e") + (uuid "898eab24-e02a-4dd2-adee-dc935da65320") (effects (font (size 1.27 1.27) @@ -26613,10 +26917,10 @@ ) ) (property "Description" "" - (at 0 0 0) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "0fba9579-9f97-4316-99d4-1977ce8bd213") + (uuid "1a123e35-0dd7-4f9d-aad1-9eb95654b8e5") (effects (font (size 1.27 1.27) @@ -26625,7 +26929,7 @@ ) ) (property "KiLib_Generator" "package/gullwing" - (at 0 0 0) + (at 0 0 180) (layer "B.SilkS") (hide yes) (uuid "b8efecd5-bf04-48a8-ab8c-b110cf41cf96") @@ -26638,7 +26942,7 @@ ) ) (property "MF" "Texas Instruments" - (at 0 -2 0) + (at 0 -2 180) (layer "B.SilkS") (hide yes) (uuid "3e7019c9-cb2d-46bb-8208-a6fe8f3b36e4") @@ -26650,7 +26954,7 @@ ) ) (property "Manufacturer_Part_Number" "DRV5055A2QDBZR" - (at 0 -2 0) + (at 0 -2 180) (layer "B.SilkS") (hide yes) (uuid "9f667392-d65d-4005-9c98-1d63abd176b5") @@ -26662,7 +26966,7 @@ ) ) (property "LCSC" "C266131" - (at 0 -2 0) + (at 0 -2 180) (layer "B.SilkS") (hide yes) (uuid "a88c749a-6416-441f-b39f-f0faa1bd3700") @@ -26674,7 +26978,7 @@ ) ) (property "Stackup Path" "U_HALL1" - (at 0 -2 0) + (at 0 -2 180) (layer "B.SilkS") (hide yes) (uuid "a7e305d6-008b-4b89-8cbf-ce2a97f3ac61") @@ -26685,8 +26989,8 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:105" - (at 0 -2 0) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:106" + (at 0 -2 180) (layer "B.SilkS") (hide yes) (uuid "407ee4f6-0262-4c04-b3e2-6f2b89720048") @@ -26701,34 +27005,34 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.76 -1.56) - (end -0.76 -1.51) + (start 0.76 1.56) + (end 0.76 0.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "dde80eb3-1b22-4fde-b947-dd6074989424") + (uuid "167fc161-c6a8-49ed-91d0-9e7a1a079b54") ) (fp_line - (start -0.76 -0.39) - (end -0.76 0.39) + (start 0.76 -0.56) + (end 0.76 -1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "16c3ff93-c2a0-4ed8-a407-41291a502ff8") + (uuid "1198e229-86a3-488e-8040-7ec7d2136ba1") ) (fp_line - (start -0.76 1.51) - (end -0.76 1.56) + (start 0.76 -1.56) + (end -0.76 -1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "ea028488-b65e-4d4e-bc77-7924cb6ed942") + (uuid "b009ca57-3574-4e20-a7b6-7bb050c621ed") ) (fp_line (start -0.76 1.56) @@ -26741,34 +27045,34 @@ (uuid "619a6bb9-6c12-4716-a5e8-a1da0ea0e238") ) (fp_line - (start 0.76 -1.56) - (end -0.76 -1.56) + (start -0.76 1.51) + (end -0.76 1.56) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "b009ca57-3574-4e20-a7b6-7bb050c621ed") + (uuid "ea028488-b65e-4d4e-bc77-7924cb6ed942") ) (fp_line - (start 0.76 -0.56) - (end 0.76 -1.56) + (start -0.76 -0.39) + (end -0.76 0.39) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "1198e229-86a3-488e-8040-7ec7d2136ba1") + (uuid "16c3ff93-c2a0-4ed8-a407-41291a502ff8") ) (fp_line - (start 0.76 1.56) - (end 0.76 0.56) + (start -0.76 -1.56) + (end -0.76 -1.51) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "167fc161-c6a8-49ed-91d0-9e7a1a079b54") + (uuid "dde80eb3-1b22-4fde-b947-dd6074989424") ) (fp_poly (pts @@ -26783,164 +27087,164 @@ (uuid "e1d1bf97-e2aa-4e70-9ed4-d60dff13cd06") ) (fp_line - (start -1.93 -1.5) - (end -1.93 -0.39) + (start 1.93 0.55) + (end 1.93 -0.55) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "92c18900-ecc8-45f6-95a0-71df3bd0424a") + (uuid "b56093e4-8891-4331-9cc1-5173daceb43e") ) (fp_line - (start -1.93 -0.39) - (end -0.9 -0.39) + (start 1.93 -0.55) + (end 0.9 -0.55) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "de0df420-b5c5-4235-b939-639be462c1da") + (uuid "2db8642f-2d53-47d9-a916-2d2b42b7ecdb") ) (fp_line - (start -1.93 0.39) - (end -1.93 1.5) + (start 0.9 1.7) + (end 0.9 0.55) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "df7b9cfe-fd63-4376-960b-3db8030674a1") + (uuid "5ea78c98-723f-4a5f-a973-0ff31424002c") ) (fp_line - (start -1.93 1.5) - (end -0.9 1.5) + (start 0.9 0.55) + (end 1.93 0.55) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "431af60d-4fac-4799-b19f-d0d8b40ad760") + (uuid "fc0095e0-2b69-4634-b941-471afa99fe3b") ) (fp_line - (start -0.9 -1.7) - (end -0.9 -1.5) + (start 0.9 -0.55) + (end 0.9 -1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "1bf6c027-dd4d-4166-9c26-f085c3f09146") + (uuid "903f849f-b2bd-49cf-a610-ee3fb1905a8d") ) (fp_line - (start -0.9 -1.5) - (end -1.93 -1.5) + (start 0.9 -1.7) + (end -0.9 -1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "b049d9d7-4263-410f-b92a-72c8207fbfcc") + (uuid "ce24a11b-ef08-4f04-95be-048d4eb3cb46") ) (fp_line - (start -0.9 -0.39) - (end -0.9 0.39) + (start -0.9 1.7) + (end 0.9 1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "16c06d6b-41f9-474d-9125-8836e080fad8") + (uuid "2cb4d467-6925-4498-90be-ba0da5f56760") ) (fp_line - (start -0.9 0.39) - (end -1.93 0.39) + (start -0.9 1.5) + (end -0.9 1.7) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "3cbf097e-974b-4248-a7e9-69a98d1e7598") + (uuid "6a22ca71-4dce-4999-9417-8613e46607eb") ) (fp_line - (start -0.9 1.5) - (end -0.9 1.7) + (start -0.9 0.39) + (end -1.93 0.39) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "6a22ca71-4dce-4999-9417-8613e46607eb") + (uuid "3cbf097e-974b-4248-a7e9-69a98d1e7598") ) (fp_line - (start -0.9 1.7) - (end 0.9 1.7) + (start -0.9 -0.39) + (end -0.9 0.39) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "2cb4d467-6925-4498-90be-ba0da5f56760") + (uuid "16c06d6b-41f9-474d-9125-8836e080fad8") ) (fp_line - (start 0.9 -1.7) - (end -0.9 -1.7) + (start -0.9 -1.5) + (end -1.93 -1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "ce24a11b-ef08-4f04-95be-048d4eb3cb46") + (uuid "b049d9d7-4263-410f-b92a-72c8207fbfcc") ) (fp_line - (start 0.9 -0.55) - (end 0.9 -1.7) + (start -0.9 -1.7) + (end -0.9 -1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "903f849f-b2bd-49cf-a610-ee3fb1905a8d") + (uuid "1bf6c027-dd4d-4166-9c26-f085c3f09146") ) (fp_line - (start 0.9 0.55) - (end 1.93 0.55) + (start -1.93 1.5) + (end -0.9 1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "fc0095e0-2b69-4634-b941-471afa99fe3b") + (uuid "431af60d-4fac-4799-b19f-d0d8b40ad760") ) (fp_line - (start 0.9 1.7) - (end 0.9 0.55) + (start -1.93 0.39) + (end -1.93 1.5) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "5ea78c98-723f-4a5f-a973-0ff31424002c") + (uuid "df7b9cfe-fd63-4376-960b-3db8030674a1") ) (fp_line - (start 1.93 -0.55) - (end 0.9 -0.55) + (start -1.93 -0.39) + (end -0.9 -0.39) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "2db8642f-2d53-47d9-a916-2d2b42b7ecdb") + (uuid "de0df420-b5c5-4235-b939-639be462c1da") ) (fp_line - (start 1.93 0.55) - (end 1.93 -0.55) + (start -1.93 -1.5) + (end -1.93 -0.39) (stroke (width 0.05) (type solid) ) (layer "B.CrtYd") - (uuid "b56093e4-8891-4331-9cc1-5173daceb43e") + (uuid "92c18900-ecc8-45f6-95a0-71df3bd0424a") ) (fp_poly (pts @@ -26955,7 +27259,7 @@ (uuid "e6fc3e52-30ae-40f6-b98d-67ab36ffe2cf") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 270) (layer "B.Fab") (uuid "b9860d77-678b-44b4-9c28-4f6c3633ca7e") (effects @@ -26967,15 +27271,15 @@ ) ) (pad "1" smd roundrect - (at -0.9375 0.95) + (at -0.9375 0.95 180) (size 1.475 0.6) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/3V3_RF") + (net "3V3") (uuid "bb2ab2d0-2a2b-4dea-a8b2-6efc299ad607") ) (pad "2" smd roundrect - (at -0.9375 -0.95) + (at -0.9375 -0.95 180) (size 1.475 0.6) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -26983,7 +27287,7 @@ (uuid "53d8efb4-7b78-4a77-a55c-e957a5baefcf") ) (pad "3" smd roundrect - (at 0.9375 0) + (at 0.9375 0 180) (size 1.475 0.6) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) @@ -27153,7 +27457,7 @@ ) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:50" + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:52" (at 0 2 0) (layer "B.SilkS") (hide yes) @@ -27490,7 +27794,7 @@ (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") (property "Reference" "R_TRIG1" - (at 0 1.17 90) + (at 0 1.17 270) (layer "B.SilkS") (hide yes) (uuid "7be12c7f-3607-4ed2-a792-182faf4801cd") @@ -27503,7 +27807,7 @@ ) ) (property "Value" "1kΩ" - (at 0 -1.17 90) + (at 0 -1.17 270) (layer "B.Fab") (uuid "21b07af9-42e6-485f-8503-8082fcf2f135") (effects @@ -27515,7 +27819,7 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 270) (layer "B.Fab") (hide yes) (uuid "ca5b1979-2cd1-4f4d-8d37-4fd4398c9a7c") @@ -27527,7 +27831,7 @@ ) ) (property "Description" "" - (at 0 0 90) + (at 0 0 270) (layer "B.Fab") (hide yes) (uuid "e447da9c-176f-4c1a-be7d-cd707b83ffe9") @@ -27539,7 +27843,7 @@ ) ) (property "KiLib_Generator" "SMD_2terminal_chip_molded" - (at 0 0 90) + (at 0 0 270) (layer "B.SilkS") (hide yes) (uuid "fd3342be-0245-4dc0-bc2f-e9333d7ddd3b") @@ -27552,7 +27856,7 @@ ) ) (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 -2 90) + (at 0 -2 270) (layer "B.SilkS") (hide yes) (uuid "546a79c2-7f64-4340-8661-816897e7437c") @@ -27565,7 +27869,7 @@ ) ) (property "Manufacturer_Part_Number" "0402WGF1001TCE" - (at 0 -2 90) + (at 0 -2 270) (layer "B.SilkS") (hide yes) (uuid "f7159457-01a1-4191-835c-ca9fc59528bd") @@ -27578,7 +27882,7 @@ ) ) (property "LCSC" "C11702" - (at 0 -2 90) + (at 0 -2 270) (layer "B.SilkS") (hide yes) (uuid "ef32ead5-ccea-47f0-b42a-81046218d3f5") @@ -27591,7 +27895,7 @@ ) ) (property "Stackup Path" "R_TRIG1" - (at 0 -2 90) + (at 0 -2 270) (layer "B.SilkS") (hide yes) (uuid "3ba19737-a48d-468d-929b-a8bcad60c497") @@ -27603,8 +27907,8 @@ (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:101" - (at 0 -2 90) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:104" + (at 0 -2 270) (layer "B.SilkS") (hide yes) (uuid "e8e36e29-f135-40b1-adc7-630500afdf2a") @@ -27662,7 +27966,7 @@ (uuid "5ac62b09-8c98-45b9-9a79-21145e868d8e") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 270) (layer "B.Fab") (uuid "378badcf-d048-4240-909d-5f1f13c6f1e1") (effects @@ -27704,15 +28008,15 @@ ) (footprint "Resistor_SMD:R_0402_1005Metric" (layer "B.Cu") - (uuid "feb5b6c7-c0e2-4640-90e3-610986db5ece") - (at 144.565 98.775 90) + (uuid "fe714753-d6dd-4d04-897d-7cd5f5f5827a") + (at 121.77 101.25 180) (descr "Resistor SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC-7351 nominal, (Body size source: IPC-SM-782 page 72, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf)") (tags "resistor") - (property "Reference" "R_BOOT_PU1" - (at 0 1.17 90) + (property "Reference" "R_TS1" + (at 0 1.17 180) (layer "B.SilkS") (hide yes) - (uuid "31d329d8-e856-48f5-b21f-e8b8e112298a") + (uuid "a453dd30-5a2a-44c4-a880-818306b9a912") (effects (font (size 1 1) @@ -27722,9 +28026,9 @@ ) ) (property "Value" "10kΩ" - (at 0 -1.17 90) + (at 0 -1.17 180) (layer "B.Fab") - (uuid "cc583e60-2a44-4941-ac9a-442fc869332b") + (uuid "38311a83-d968-43a5-b963-3f4b048ffe57") (effects (font (size 1 1) @@ -27734,10 +28038,10 @@ ) ) (property "Datasheet" "" - (at 0 0 90) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "e0f41ae2-a612-4ecb-8910-bc3bcdbfc9e8") + (uuid "b626d0d2-b116-410b-b877-ce4a93ceda2b") (effects (font (size 1.27 1.27) @@ -27746,10 +28050,10 @@ ) ) (property "Description" "Resistor" - (at 0 0 90) + (at 0 0 180) (layer "B.Fab") (hide yes) - (uuid "95318fe0-1939-4a96-82bb-496eb372b979") + (uuid "8031d0c6-9cf6-48ae-a7b5-2cc5b5efe364") (effects (font (size 1.27 1.27) @@ -27758,11 +28062,11 @@ ) ) (property "MF" "UNI-ROYAL(Uniroyal Elec)" - (at 0 0 270) + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "f3cc76e9-b47f-49b6-abe7-24850ee08854") + (uuid "3c84c8f9-6671-4a55-b309-d44dbab736e3") (effects (font (size 1 1) @@ -27772,11 +28076,11 @@ ) ) (property "Manufacturer_Part_Number" "0402WGF1002TCE" - (at 0 0 270) + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "5d4bab60-8ee2-4e4e-986b-3320d6c2829f") + (uuid "9a085838-8dc1-45ec-a649-e19d6bdc87c1") (effects (font (size 1 1) @@ -27786,11 +28090,11 @@ ) ) (property "LCSC" "C25744" - (at 0 0 270) + (at 0 0 180) (unlocked yes) (layer "B.Fab") (hide yes) - (uuid "4509dd1f-bafc-48fb-b332-54d7e413e331") + (uuid "ddb9cc9d-b7d3-4699-9670-75f91179c8d1") (effects (font (size 1 1) @@ -27799,34 +28103,32 @@ (justify mirror) ) ) - (property "Stackup Path" "R_BOOT_PU1" - (at 2 0 180) + (property "Stackup Path" "R_TS1" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "f3d3e6c1-4bc9-4b68-9204-80b16a8d2ce6") + (uuid "d88ed2b2-a397-4355-b282-27f49ec99d2b") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) - (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:53" - (at 2 0 180) + (property "Stackup Source" "PCB/v2.x/stackup/board.kdl:71" + (at 0 -2 180) (layer "B.SilkS") (hide yes) - (uuid "5ff8f76a-e48e-468b-b6b8-9c08a8f10518") + (uuid "be24c03a-6f38-4cf0-9939-c074181dbb1a") (effects (font (size 1.27 1.27) (thickness 0.15) ) - (justify mirror) ) ) (property ki_fp_filters "R_*") - (path "/458f2090-917f-58d0-aed4-6553732ff17f") + (path "/f8467960-077e-5dfa-ad5f-583d827e1496") (units (unit (name "A") @@ -27836,24 +28138,24 @@ (attr smd) (duplicate_pad_numbers_are_jumpers no) (fp_line - (start -0.153641 -0.38) - (end 0.153641 -0.38) + (start -0.153641 0.38) + (end 0.153641 0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "f869a1aa-2cbf-43b0-b997-f12524de0b07") + (uuid "f66a0c43-8a90-421f-942d-79424dd79a66") ) (fp_line - (start -0.153641 0.38) - (end 0.153641 0.38) + (start -0.153641 -0.38) + (end 0.153641 -0.38) (stroke (width 0.12) (type solid) ) (layer "B.SilkS") - (uuid "8f49ea27-b944-4326-904d-57603b45e24d") + (uuid "bba4ce97-f66d-4840-aa22-478584dc2ece") ) (fp_rect (start -0.93 0.47) @@ -27864,7 +28166,7 @@ ) (fill no) (layer "B.CrtYd") - (uuid "1f236e61-f049-4f06-a913-acb12aa6fa14") + (uuid "fd4d52da-3502-473a-a0e7-4065cd5aa3e3") ) (fp_rect (start -0.525 0.27) @@ -27875,12 +28177,12 @@ ) (fill no) (layer "B.Fab") - (uuid "d940bf26-785c-421d-8a0f-5e90931d506b") + (uuid "29f7db3e-c537-498a-9c16-764d72295de9") ) (fp_text user "${REFERENCE}" - (at 0 0 90) + (at 0 0 180) (layer "B.Fab") - (uuid "647dffde-a817-4181-a9eb-19e0871bb307") + (uuid "aaf3dfbe-42d4-4dd0-8e3f-6495cec0f440") (effects (font (size 0.26 0.26) @@ -27890,22 +28192,22 @@ ) ) (pad "1" smd roundrect - (at -0.51 0 90) + (at -0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "/MCU_Core/MCU_BOOT") + (net "/Power_Charger/CHG_TS") (pintype "passive") - (uuid "8f32a9e7-08e3-47c6-8991-e685d0e80089") + (uuid "241f4cdd-9b3a-42aa-b258-efeef884ee02") ) (pad "2" smd roundrect - (at 0.51 0 90) + (at 0.51 0 180) (size 0.54 0.64) (layers "B.Cu" "B.Mask" "B.Paste") (roundrect_rratio 0.25) - (net "3V3") + (net "GND") (pintype "passive") - (uuid "22fafb5e-bada-49fb-9067-3b8e4ed0d64d") + (uuid "5a566ea4-933f-4c3e-aaad-12f462eee6a7") ) (embedded_fonts no) (model "${KICAD10_3DMODEL_DIR}/Resistor_SMD.3dshapes/R_0402_1005Metric.step" @@ -27942,8 +28244,19 @@ ) ) ) + (gr_text "BOOT" + (at 147.15 110.7 0) + (layer "F.SilkS") + (uuid "9b837eab-2d14-4199-8708-76183320b5c4") + (effects + (font + (size 0.8 0.8) + (thickness 0.12) + ) + ) + ) (gr_text "GND" - (at 122.1 112.7 270) + (at 122.1 114.7 270) (layer "F.SilkS") (uuid "077c0acb-eaa4-4050-bca3-f59c0c2361f7") (effects @@ -27954,7 +28267,7 @@ ) ) (gr_text "3V3" - (at 123.4 112.6 270) + (at 123.4 114.6 270) (layer "F.SilkS") (uuid "bf6e9f05-3327-4c78-9335-32edc8d16f92") (effects @@ -27965,7 +28278,7 @@ ) ) (gr_text "SDA" - (at 124.8 112.6 270) + (at 124.8 114.6 270) (layer "F.SilkS") (uuid "ef4373d9-df7d-490d-b993-d443109188bc") (effects @@ -27976,7 +28289,7 @@ ) ) (gr_text "SCL" - (at 126.1 112.6 270) + (at 126.1 114.6 270) (layer "F.SilkS") (uuid "b0f5139b-2e3b-4c3e-805a-5c33cd64b684") (effects @@ -27986,30 +28299,6 @@ ) ) ) - (gr_text "BOOT" - (at 146.18 108.209999 0) - (layer "B.SilkS") - (uuid "9b837eab-2d14-4199-8708-76183320b5c4") - (effects - (font - (size 0.8 0.8) - (thickness 0.12) - ) - (justify mirror) - ) - ) - (gr_text "RESET" - (at 147 99.3 0) - (layer "B.SilkS") - (uuid "5852178c-0ed9-41b3-8fd2-b7b282ecfd74") - (effects - (font - (size 0.8 0.8) - (thickness 0.12) - ) - (justify mirror) - ) - ) (gr_text "+" (at 144.7 115.8 0) (layer "B.SilkS") @@ -28035,1652 +28324,1748 @@ ) ) (segment - (start 139.975 112.075) - (end 139.975 113.375) + (start 128.9 127.6) + (end 127.85 128.65) + (width 0.2) + (layer "F.Cu") + (net "3V3") + (uuid "0bef0bb4-ba38-4896-9c13-2c99ccc3bd52") + ) + (segment + (start 123.88 106.3) + (end 123.88 108.105) (width 0.3) (layer "F.Cu") - (net "VSYS") - (uuid "03c5fad6-fdc0-4c96-aff0-9aac3476678d") + (net "3V3") + (uuid "1cdf74e0-4728-4f1a-98c8-f6860bf626f2") ) (segment - (start 130.3517 79.3894) - (end 130.3517 72.8233) - (width 0.4) + (start 125.134276 125.08) + (end 125.8 125.08) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "0b424e66-6dc5-4310-baa1-bef0981fe311") + (net "3V3") + (uuid "2361494e-fad3-41c0-8029-2d283c1018a1") ) (segment - (start 141.15 114.3) - (end 140.9 114.3) + (start 130.620864 128.030312) + (end 130.190552 127.6) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "11577c26-a0a6-4e33-9492-83edfac7a69f") + (net "3V3") + (uuid "25755e31-ad04-4e55-818a-3111f5abeaef") ) (segment - (start 132.25 120.315) - (end 134.75 120.315) + (start 146.51 118.6) + (end 145.69 117.78) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "1c861806-321f-4b68-b004-fda2fc8f7f48") + (net "3V3") + (uuid "2ca204bb-4e65-457b-8e9f-fad6d4d87683") ) (segment - (start 131.1972 100.4724) - (end 131.1972 105.1092) - (width 0.4) + (start 130.620864 129.45) + (end 130.620864 128.030312) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "3311cf7f-6924-40f0-8dcf-98b6ba18b0ca") + (net "3V3") + (uuid "30b07a77-eae9-4672-9f97-db89a7c6d224") ) (segment - (start 134.75 119.2748) - (end 135.9598 118.065) - (width 0.4) + (start 140.6 102.08) + (end 140.49 102.19) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "37b204e1-2a04-4c41-a336-8d81d943ca1b") + (net "3V3") + (uuid "376ed02f-412a-4e82-bc8b-7b7031d3aca6") ) (segment - (start 135.9598 118.065) - (end 136.5474 118.065) - (width 0.4) + (start 145.8 107.275) + (end 145.8 108.9) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "384a3c19-70a0-4872-897a-a2e52457a380") + (net "3V3") + (uuid "3a201089-6b73-4bd0-8e81-fcbcb02f2131") ) (segment - (start 139.975 113.375) - (end 140.9 114.3) - (width 0.3) + (start 125.08 124.896016) + (end 125.08 125.025724) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "45237574-8443-41c6-9690-845bd6cf8bbd") + (net "3V3") + (uuid "47a6461f-1308-4df1-936b-77ef8f2dcee1") ) (segment - (start 133.5515 92.0359) - (end 131.0911 94.4963) - (width 0.4) + (start 125.5 105.28) + (end 125.5 104.673528) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "4c1baaaf-5aae-4965-a92f-8de7e618d0d0") + (net "3V3") + (uuid "4d203ad7-0733-4dbf-9be8-4189a291dc12") ) (segment - (start 127.561 90.825) - (end 126.9687 90.2327) - (width 0.4) + (start 145.3 106.775) + (end 145.8 107.275) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "57e324f8-43b5-48eb-bc8c-725698f2fb02") + (net "3V3") + (uuid "55a1059b-4215-40bc-b4d6-f103e2ee286e") ) (segment - (start 140.9 114.3) - (end 138.9361 116.2639) - (width 0.4) + (start 125.08 125.025724) + (end 125.134276 125.08) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "5bdf8a39-4910-43de-97f4-4c495eb13e69") + (net "3V3") + (uuid "57530090-7fd0-4358-befc-6afc32d9068a") ) (segment - (start 131.0911 100.3663) - (end 131.1972 100.4724) - (width 0.4) + (start 139.99 102.69) + (end 140.6 102.08) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "65d6bd90-591d-43f7-a81e-057c5ca3b486") + (net "3V3") + (uuid "57952f94-e4b5-4f8e-b612-9b14aab7903b") ) (segment - (start 133.5515 90.6675) - (end 133.5515 92.0359) - (width 0.4) + (start 145.3 106.775) + (end 145.3 107.602405) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "67be328d-ea01-4cde-ae36-8e102bfcd528") + (net "3V3") + (uuid "6bcb39b9-3c4b-4d85-bc05-238aa503e808") ) (segment - (start 126.9687 90.2327) - (end 126.9687 82.7724) - (width 0.4) + (start 124.95 104.123528) + (end 124.18 104.893528) + (width 0.3) (layer "F.Cu") - (net "VSYS") - (uuid "7e8bb958-c563-426d-a248-7fae932c1c4c") + (net "3V3") + (uuid "92558152-365f-415c-8cee-967905189951") ) (segment - (start 134.75 119.190501) - (end 134.75 120.315) + (start 140.6 105.35) + (end 140.75 105.5) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "84d064b7-85b6-451f-9862-fbd6083b2086") + (net "3V3") + (uuid "950a7a23-4eee-48c3-a9c3-163488970ba8") ) (segment - (start 130.3517 72.8233) - (end 131.135 72.04) - (width 0.4) + (start 139.99 103.42) + (end 139.99 102.69) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "8e842030-bceb-4f21-8faf-9444c0135e51") + (net "3V3") + (uuid "95d546d1-345e-462d-bee4-cb92066d9b56") ) (segment - (start 126.9687 82.7724) - (end 130.3517 79.3894) - (width 0.4) + (start 123.88 108.105) + (end 123.9 108.125) + (width 0.3) (layer "F.Cu") - (net "VSYS") - (uuid "9eda2a03-20b7-4f90-a535-d0c096aec575") + (net "3V3") + (uuid "9a714c9a-bef3-4c7e-8fe3-8c537d2f8bcc") ) (segment - (start 130.8 119.115) - (end 130.8 119.765) + (start 140.921174 104.03) + (end 141.06811 104.176936) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "aeff7000-c623-493c-ba8a-ee3efc7c5c3c") + (net "3V3") + (uuid "9e45d872-937a-480b-b5f4-6b69e65d12a4") ) (segment - (start 135.7753 113.6907) - (end 135.7753 108.3362) - (width 0.4) + (start 140.6 104.03) + (end 140.6 105.35) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "b398b4ce-30e2-4093-81d9-56d9403ea56b") + (net "3V3") + (uuid "a0f7538a-c7e6-440a-94e9-a15a2c6b30b2") ) (segment - (start 131.0911 94.4963) - (end 131.0911 100.3663) - (width 0.4) + (start 125.5 104.673528) + (end 124.95 104.123528) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "c65c1ce3-13a9-4915-9347-793d5908ffbb") + (net "3V3") + (uuid "ac751916-d89f-4e0d-a6fd-3638419fad42") ) (segment - (start 136.5474 118.065) - (end 138.3485 116.2639) - (width 0.4) + (start 127.2 106.39) + (end 126.33 106.39) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "c8c64b77-f675-4c3d-8b52-d7d32383d3ea") + (net "3V3") + (uuid "b2e5f946-5490-41a9-8bb4-22570f04ab7c") + ) + (segment + (start 124.18 106) + (end 123.88 106.3) + (width 0.3) + (layer "F.Cu") + (net "3V3") + (uuid "c12c74ba-57d4-4ae5-baac-ba1d4dac724f") ) (segment - (start 131.35 120.315) - (end 132.25 120.315) + (start 140.6 104.03) + (end 139.99 103.42) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "dd9780fa-8643-44f1-ad55-c34809c6cf3a") + (net "3V3") + (uuid "c9972bb7-2e4f-4f6a-8eea-91b9bf2e30b7") ) (segment - (start 138.3485 116.2639) - (end 135.7753 113.6907) - (width 0.4) + (start 140.6 104.03) + (end 140.921174 104.03) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "e150182d-9b81-4a12-98d0-5d62a82581b3") + (net "3V3") + (uuid "d992edd0-d100-4dec-829b-1d5c61bd57a2") ) (segment - (start 138.9361 116.2639) - (end 138.3485 116.2639) - (width 0.4) + (start 145.3 107.602405) + (end 145.311599 107.614004) + (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "ee577d0c-dd23-45d7-a609-7c660d8a5422") + (net "3V3") + (uuid "ded25aba-6df3-40ad-845c-b793a6cf5757") ) (segment - (start 130.8 119.765) - (end 131.35 120.315) + (start 126.33 106.39) + (end 126.32 106.4) (width 0.2) (layer "F.Cu") - (net "VSYS") - (uuid "f25a7971-73ac-42e6-9243-9d506dd18296") + (net "3V3") + (uuid "dfaa6877-6b7a-4b3a-ae45-bf6cb8c4a3df") + ) + (segment + (start 145.69 117.78) + (end 145.5 117.78) + (width 0.2) + (layer "F.Cu") + (net "3V3") + (uuid "dfedbbe3-ea15-4856-9d3a-e8f6bf12440e") + ) + (segment + (start 124.18 104.893528) + (end 124.18 106) + (width 0.3) + (layer "F.Cu") + (net "3V3") + (uuid "e8a86c3d-4b9b-4681-9b64-8c8298fefcd8") + ) + (segment + (start 130.190552 127.6) + (end 128.9 127.6) + (width 0.2) + (layer "F.Cu") + (net "3V3") + (uuid "fa6765d4-0c59-4716-a26f-069af5af3d9d") ) (via - (at 131.134999 72.039999) + (at 127.76125 93.014999) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VSYS") - (uuid "217c5721-8178-4baa-9ddb-43334a2a7999") + (net "3V3") + (uuid "0f4f1edf-a314-43f2-b547-e767466e9184") ) (via - (at 133.5515 90.6675) + (at 145.311599 107.614004) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VSYS") - (uuid "7537d8bc-bda9-465e-90c1-f84a3f33daf8") + (net "3V3") + (uuid "254d9aee-0686-4287-adaf-dd0c0915c014") ) (via - (at 131.1972 105.1092) + (at 136.012023 99.792121) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VSYS") - (uuid "a5aeb06b-beb5-48cd-94ac-a4537a310e95") + (net "3V3") + (uuid "2631d15a-e329-4ddd-92c1-a48165737ccf") ) (via - (at 135.7753 108.3362) + (at 131.1 101.1) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VSYS") - (uuid "ccb543b5-5fd6-422e-97ed-29943eeca363") + (net "3V3") + (uuid "27dc77e8-5b29-49e2-88bb-24421cd72969") ) (via - (at 127.56125 90.824999) + (at 132.248535 126.920005) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VSYS") - (uuid "f5e8d6a4-7090-4c5d-b4c6-55674e82bc28") + (net "3V3") + (uuid "349d1f54-a2ef-4cf8-add7-76f367aac942") + ) + (via + (at 127.2 127.7625) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "475d61f5-bd74-415c-a735-91ec6eca69f7") + ) + (via + (at 124.95 104.123528) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "4928cd7c-78b2-424d-9dea-3c045aaa9993") + ) + (via + (at 134.2 106.4) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "5135f578-ca29-4914-9559-0079a690ae92") + ) + (via + (at 125.08 124.896016) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "667ceb39-feb4-4394-921c-7d35beb21479") + ) + (via + (at 123.9 98.1) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "70e548f2-990b-4641-bb69-1d6e4070492b") + ) + (via + (at 141.06811 104.176936) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "74a4f90d-cdd8-4933-81d7-cc0d3e8b2237") + ) + (via + (at 130.620864 129.45) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "81ba8c81-8fae-4d4d-be3c-d78d8baf8426") + ) + (via + (at 129 64.6) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "8901e69c-6ddc-4a28-8a43-852a186c554c") + ) + (via + (at 126.32 106.4) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "a36525e3-2b72-47cc-bf56-986fdaf4fb9b") + ) + (via + (at 145.5 117.78) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "ba06e4d2-88a0-4e24-a75e-878d5b42782a") + ) + (via + (at 138.5 93.25) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "c06f2257-c729-4a58-8712-f9a4ee36d4eb") + ) + (via + (at 137.4 100.2) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "3V3") + (uuid "e5272ea8-dcfc-4725-b05c-01da5c9a5ccd") ) (segment - (start 141.405 76.34) - (end 140.785 76.96) + (start 131.6375 126.8625) + (end 131.5375 126.7625) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "15f3a351-859d-4613-ac5a-8a6a1e086618") + (net "3V3") + (uuid "02bf4616-c005-4f34-88af-b9b99983b118") ) (segment - (start 131.334999 71.539999) - (end 134.083696 71.539999) + (start 125.121016 125.346016) + (end 125.475 125.7) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "18efb9b6-467e-49dc-b22d-26d7b7883d70") + (net "3V3") + (uuid "0f5e7364-48d6-42b9-88e7-4fa5fad2a7f5") ) (segment - (start 135.7753 108.3362) - (end 134.4242 108.3362) - (width 0.4) + (start 132.248535 126.920005) + (end 131.96569 126.920005) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "1c152aef-432e-4ad5-b29d-5a84aacd1565") + (net "3V3") + (uuid "222c72a6-f7db-4e04-b164-4a7bc185a260") ) (segment - (start 139.235 77.065) - (end 140.68 77.065) + (start 139.5 95.75) + (end 138.975 95.75) + (width 0.55) + (layer "B.Cu") + (net "3V3") + (uuid "24d75559-710f-4a0a-aa7c-2bbf9f1f2472") + ) + (segment + (start 138.11 98.49) + (end 138.525 98.49) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "343d2efd-379e-45cb-8e0f-9f2c961d7d66") + (net "3V3") + (uuid "2b152350-cb68-4ceb-84b1-4d07510ba6f0") ) (segment - (start 125.881 89.055) - (end 125.8813 89.0547) - (width 0.4) + (start 139.5 95.75) + (end 139.5 97.515) + (width 0.55) (layer "B.Cu") - (net "VSYS") - (uuid "3eee3608-c649-409d-82d8-f207337f7989") + (net "3V3") + (uuid "2ffc1e56-a56c-4caa-8237-a6641d6f9bc0") ) (segment - (start 141.153924 75.37) - (end 141.405 75.621075) + (start 127.2 127.7625) + (end 128.9 127.7625) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "655f7798-5f24-48c1-850f-f7a7db8ab86b") + (net "3V3") + (uuid "46b84283-e4da-4d2f-b7d3-f12c0bb908e0") ) (segment - (start 137.913696 75.37) - (end 141.153924 75.37) + (start 137.4 100.2) + (end 137.4 99.2) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "781d09a8-b13c-4d21-acbc-19b1d288b78b") + (net "3V3") + (uuid "4ac752ce-b071-4e19-8cba-6b67ef288e4b") ) (segment - (start 140.68 77.065) - (end 140.785 76.96) - (width 0.55) + (start 123.65 97.85) + (end 123.9 98.1) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "793cc62e-d2aa-47dd-88f4-47dea7238aeb") + (net "3V3") + (uuid "549ccbbe-7c30-487b-9658-cbb0a657dbc5") ) (segment - (start 134.083696 71.539999) - (end 134.484348 71.940652) + (start 135.107879 99.792121) + (end 134.85 100.05) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "7d4ed397-0c8b-4d95-8552-b42b34c5dbc5") + (net "3V3") + (uuid "5716bab6-8894-45a4-a2a0-70e6684de70d") ) (segment - (start 134.484348 71.940652) - (end 137.913696 75.37) + (start 144.005 75.725) + (end 143.73 76) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "8e8a9baa-83f0-440e-82af-0d4ec67cf0bb") + (net "3V3") + (uuid "64705730-c56e-4d64-9e96-e69e595f4188") ) (segment - (start 133.265 91.615) - (end 133.265 90.954) - (width 0.4) + (start 130.5625 129.391636) + (end 130.620864 129.45) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "9756ef3b-4cb0-4bf3-8530-9779b328f7ce") + (net "3V3") + (uuid "683729a0-0adb-4756-a1b9-7097402caaca") ) (segment - (start 127.56125 90.824999) - (end 128.46125 91.725) + (start 128.94 64.54) + (end 129 64.6) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "98fce83c-c60a-49f5-9fa4-723574842903") + (net "3V3") + (uuid "697d706d-596e-43a6-94f0-84e66a69f51a") ) (segment - (start 131.334999 71.84) - (end 131.134999 72.039999) + (start 138.025 94.8) + (end 138.025 93.725) + (width 0.55) + (layer "B.Cu") + (net "3V3") + (uuid "72dd92c6-4a50-41e8-8be7-8056d6de2c09") + ) + (segment + (start 127.4375 63.8) + (end 128.94 63.8) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "9b3331dd-0c24-45de-8a7c-accc99ab30a4") + (net "3V3") + (uuid "73f63e17-274c-4e14-8b8d-8b11ff39474b") ) (segment - (start 133.265 90.954) - (end 133.5515 90.6675) - (width 0.4) + (start 131.96569 126.920005) + (end 131.908185 126.8625) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "a5c335f1-293f-4ffd-8476-d2b01e0496f9") + (net "3V3") + (uuid "77dc7afc-62a0-43a8-9e55-a75e7f799c61") ) (segment - (start 125.8813 89.0547) - (end 125.8813 88.965) - (width 0.4) + (start 127.66 128.5) + (end 127.66 128.2225) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "a8429164-d5fe-446f-99bb-a89c25ede4ff") + (net "3V3") + (uuid "791eccfc-f8ca-4760-ab79-e2e5ac2a322e") ) (segment - (start 141.405 75.621075) - (end 141.405 76.34) + (start 128.94 63.8) + (end 128.94 64.54) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "c4d2b77b-596f-4567-9b00-d1201250f6a3") + (net "3V3") + (uuid "7b294b1d-4866-4db5-8e0c-c9e6a56b0f28") ) (segment - (start 134.4242 108.3362) - (end 131.1972 105.1092) - (width 0.4) + (start 138.975 95.75) + (end 138.025 94.8) + (width 0.55) (layer "B.Cu") - (net "VSYS") - (uuid "d2c2eca7-6626-4aeb-bced-e1d2f2555dbd") + (net "3V3") + (uuid "7b67e9cf-d952-44e3-8487-28d8a798a517") ) (segment - (start 125.88125 89.145) - (end 127.56125 90.824999) + (start 134.85 100.05) + (end 133.86 100.05) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "e1f106c8-7294-4403-b511-630d7c72f4a8") + (net "3V3") + (uuid "80397692-4570-42c4-9aee-e78e2f612ee3") ) (segment - (start 125.88125 88.965) - (end 125.88125 89.145) + (start 125.121016 124.937032) + (end 125.121016 125.346016) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "edd856cb-8d30-483a-af71-2313c48cca85") + (net "3V3") + (uuid "90951014-b589-4194-ab86-8e2be6785be1") ) (segment - (start 131.334999 71.539999) - (end 131.334999 71.84) + (start 131.26 101.1) + (end 131.53 101.37) (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "f3cb6b8b-85d9-4b9f-b75f-ee6c94f64567") + (net "3V3") + (uuid "95428d8c-53a8-4adb-b4f2-b623b93cf111") ) (segment - (start 128.4613 91.725) - (end 128.461 91.725) - (width 0.4) + (start 134.07 106.27) + (end 134.2 106.4) + (width 0.2) (layer "B.Cu") - (net "VSYS") - (uuid "fdf338cb-26c4-4e55-a068-3f1f1a1891dc") + (net "3V3") + (uuid "9988dfa3-e4b0-409d-800b-743343957533") ) (segment - (start 127.561 90.825) - (end 133.394 90.825) - (width 0.4) - (layer "In1.Cu") - (net "VSYS") - (uuid "0d4851bb-a75c-4e46-b717-e01645fcf296") + (start 126.72 125.9) + (end 125.675 125.9) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "a06b9309-b807-4092-8ff0-b71a6dacd054") ) (segment - (start 133.394 90.825) - (end 133.5515 90.6675) - (width 0.4) - (layer "In1.Cu") - (net "VSYS") - (uuid "1135a429-d013-4aab-820a-2ce8d29c9b0d") + (start 130.5625 128.425) + (end 130.5625 129.391636) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "a2cc2928-fdde-4bab-bce6-fbf48120efb2") ) (segment - (start 122.6 105.4) - (end 122.35 105.15) + (start 127.66 128.2225) + (end 127.2 127.7625) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0406d96d-9596-45ec-9e7e-5ac885649a79") + (layer "B.Cu") + (net "3V3") + (uuid "aee90e9c-3ace-4be2-bfef-cb0231b155b2") ) (segment - (start 136.65 120.315) - (end 136.65 119.215) - (width 0.3) - (layer "F.Cu") - (net "GND") - (uuid "05b6272d-ce3c-41a0-94a6-65a7d9a85929") + (start 131.908185 126.8625) + (end 131.6375 126.8625) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "af97de8c-8ad8-426f-ac87-c60a04525a21") ) (segment - (start 123.175 95.975) - (end 123.4 95.975) + (start 131.1 101.1) + (end 131.26 101.1) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0683ad8c-a997-49c0-b447-1136a0c425f9") + (layer "B.Cu") + (net "3V3") + (uuid "b1058c0b-8566-4622-ac04-f541710a2f88") ) (segment - (start 140.925 109.8) - (end 140.925 109.025) - (width 0.3) - (layer "F.Cu") - (net "GND") - (uuid "06d88bbc-d2f0-449e-9155-b62073d4749f") + (start 131.5375 126.7625) + (end 130.725 126.7625) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "b32ac827-d297-4e4f-83bc-deaf8a6b4afc") ) (segment - (start 142.55 103.3) - (end 142.8 103.05) + (start 127.38125 93.395) + (end 127.76125 93.014999) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0d908e30-9c3a-46a5-9bba-694311e37e00") + (layer "B.Cu") + (net "3V3") + (uuid "b5685aea-0026-4cb6-b588-59a9dbd29666") ) (segment - (start 129.65 125.55) - (end 129.65 125.35) + (start 131.53 101.37) + (end 131.53 103.6) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0df21324-65c3-4ae5-ba15-61bda08a5421") + (layer "B.Cu") + (net "3V3") + (uuid "c3d39b36-781e-430e-b810-9a73d8a36516") ) (segment - (start 148.2 83.2) - (end 148.35 83.2) - (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0e88553b-5dc9-48dd-8a59-702635591c47") + (start 139.5 97.515) + (end 138.525 98.49) + (width 0.55) + (layer "B.Cu") + (net "3V3") + (uuid "c9464ede-a5d8-4179-a0b0-fe18aa47a5b8") ) (segment - (start 123.6 83.2) - (end 123.95 83.2) + (start 136.012023 99.792121) + (end 135.107879 99.792121) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0e895208-4ce6-4d43-9885-92be6493dd8f") + (layer "B.Cu") + (net "3V3") + (uuid "cb370c41-e930-4a79-adee-8e00c1df531e") + ) + (segment + (start 138.025 93.725) + (end 138.5 93.25) + (width 0.55) + (layer "B.Cu") + (net "3V3") + (uuid "ccf9b1f4-982d-4d7b-ac93-a2902dd25d31") ) (segment - (start 145.65 96) - (end 145.45 95.8) - (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "0f2dc485-8517-4f3d-a30f-46489435b161") + (start 141 95.75) + (end 139.5 95.75) + (width 0.55) + (layer "B.Cu") + (net "3V3") + (uuid "cdf0508e-4083-4152-9762-cf62a6661042") ) (segment - (start 140.925 109.025) - (end 140.5 108.6) - (width 0.3) - (layer "F.Cu") - (net "GND") - (uuid "10c22000-b1c2-4f59-b434-a99faaa874e6") + (start 145.505 75.725) + (end 144.005 75.725) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "cf3cfbf4-53e8-4a91-a352-71ec8e1cab30") ) (segment - (start 128.625 103.175) - (end 128.4 103.175) + (start 134.07 103.6) + (end 134.07 106.27) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "159cc50b-8a02-415c-a68b-cab883c461a7") + (layer "B.Cu") + (net "3V3") + (uuid "d9a06476-3a6f-453b-950e-4b91bd56fad3") ) (segment - (start 132.72 119.345) - (end 132.25 119.345) - (width 0.3) - (layer "F.Cu") - (net "GND") - (uuid "18742d70-9c68-4ab1-8872-8efcce64b693") + (start 127.38125 93.764999) + (end 127.38125 93.395) + (width 0.2) + (layer "B.Cu") + (net "3V3") + (uuid "dd91ecbb-be1b-40d4-9de0-64f97faf00fd") ) (segment - (start 148.2 73.2) - (end 147.6 73.2) + (start 123.65 97.25) + (end 123.65 97.85) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "1879f8f7-2a5e-4711-a429-7125e5578528") + (layer "B.Cu") + (net "3V3") + (uuid "de9ca988-eb94-44e4-9474-c93e1ef6d735") ) (segment - (start 136.6 96.1) - (end 136.6 95.6) + (start 134.07 103.37) + (end 134.07 103.6) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "18cc83c7-5f93-44b0-9081-f4eacfee6b84") + (layer "B.Cu") + (net "3V3") + (uuid "e9e0d9ef-f0cc-445b-bf84-22b3c880bd0d") ) (segment - (start 145.825 96.05) - (end 146.175 96.4) + (start 125.08 124.896016) + (end 125.121016 124.937032) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "1d8b77a4-942a-4786-80ed-a203f6d794fb") + (layer "B.Cu") + (net "3V3") + (uuid "ef10011b-d4d2-4810-8fad-d0d78617e86b") ) (segment - (start 133.449999 122.4) - (end 133.4 122.4) + (start 137.4 99.2) + (end 138.11 98.49) (width 0.2) - (layer "F.Cu") - (net "GND") - (uuid "1d8dc9c5-0e28-4ee9-893c-b39aa825f982") + (layer "B.Cu") + (net "3V3") + (uuid "f32fb777-09d6-4a11-b1f6-eb499a9f3d0e") ) (segment - (start 140.675 122.275) - (end 140.525 122.275) + (start 124.6 96.4) + (end 124.75 96.25) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "2040f81b-a1fe-4866-9381-4034aa3062e6") + (uuid "01a691be-84e2-48cc-add0-c64445da36f5") ) (segment - (start 123 83.2) - (end 122.7 83.5) + (start 146.1 73.5) + (end 145.6 73) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "216e7b03-53ce-4b6b-8d75-eefe6ea4c4ba") + (uuid "026ee9e9-3e74-4b75-8ba7-f230cf42fd0d") ) (segment - (start 128.4 103.175) - (end 127.975 103.6) + (start 126.41 124.73) + (end 126.41 125.500552) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "23d65919-dff3-430a-b9eb-f97c4db89020") + (uuid "048ef1a9-3625-47d9-b574-0600f82b8ce2") ) (segment - (start 140.4 122.4) - (end 140.25 122.55) + (start 140.6 103.07) + (end 141.495 103.07) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "26734969-9eeb-4ad2-8ab9-338dbef0807b") + (uuid "06f7a0a6-ecee-447e-9a9e-e9e083005d4b") ) (segment - (start 123.4 95.975) - (end 123.825 96.4) + (start 131.2 117.8) + (end 131.3 117.8) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "2d4db83e-5f8e-4049-8c03-a9fa817f99b7") + (uuid "0a527c3d-9aff-4120-b81c-de1b406de658") ) (segment - (start 131.45 117.565) - (end 131.4 117.515) + (start 132.33 103.6) + (end 131.6 102.87) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "31ebb2de-e41d-4735-9665-01a8888534d4") + (uuid "0b116971-d85d-4e01-8e70-9290f5d92536") ) (segment - (start 132.449999 103.85) - (end 132.15 104.15) + (start 136.5 112.5) + (end 136.5 110.85) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "326b0666-726b-4842-8862-e9a3db7d8bf1") + (uuid "0c0eff03-2b86-41a2-9e79-29ecdf3bd727") ) (segment - (start 145.65 96.1) - (end 145.65 96) + (start 137.5 69.77) + (end 138.17 69.77) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "34bde728-04c5-482b-b928-fe5c06887f29") + (uuid "0d00b794-89ef-4e65-b8ff-fefc0523860e") ) (segment - (start 129.75 118.315) - (end 129.886397 118.315) + (start 146.075 116.575) + (end 144.175 116.575) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "38bdff38-bc92-4c88-ac46-b9fb221ed0d8") + (uuid "0fad0d02-0e98-4f78-a143-4c7d5f01440b") ) (segment - (start 132.449999 96.1) - (end 132.199999 96.1) + (start 137.799998 103) + (end 137.675 103) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "3975adad-37c0-4146-a993-1b6ec205b379") + (uuid "10326c26-ef45-4d72-9332-e061b482039a") ) (segment - (start 123.4 103.175) - (end 123.825 103.6) + (start 129.5 119.5) + (end 131.2 117.8) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "40781569-2089-4a0b-a527-d120d18d02e9") + (uuid "17b7b4c7-be66-41dc-905a-a7dfc9bf6b6a") ) (segment - (start 140.55 122.4) - (end 140.8 122.15) + (start 146.5 96.4) + (end 147.05 96.95) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "44410822-82a0-4449-8b83-35bbe685547f") + (uuid "1d1c98db-2dfc-4369-9ad4-881b9a8e7467") ) (segment - (start 140.25 122.55) - (end 140.25 123.105) + (start 131.6 102.87) + (end 131.8 102.67) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "447ba999-5a45-4fdf-a257-2826c19ae70d") + (uuid "1d506794-c96a-468f-92bb-a4855d15fa44") ) (segment - (start 123.3 103.3) - (end 123.05 103.05) + (start 125.8 124.12) + (end 126.41 124.73) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "46a2d9fb-fa88-464a-8ec3-aef3885651ee") + (uuid "209afb3a-d022-40d9-b377-6c7b2a822288") ) (segment - (start 123.6 83.2) - (end 123 83.2) + (start 137.5 69.77) + (end 137.5 67.2) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "499edc3a-07d6-484c-8ab9-f15f77f33c86") + (uuid "21e0e6c7-71eb-4dd1-a70d-0c4f3f19175e") ) (segment - (start 122.65 105.4) - (end 122.6 105.4) + (start 123 125.32) + (end 123.12 125.2) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "4d4ac502-6ccb-43cb-ad85-a186fd50412d") + (uuid "228fb70e-41a0-4bbd-8db2-2e28dd5af6ea") ) (segment - (start 121.77 115.52) - (end 121.75 115.5) + (start 142.73 121.68) + (end 140.75 119.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "4e0457cb-86f5-4493-a27b-2865ca2039d3") + (uuid "248e89e5-7305-4d06-9574-6cb5a0a397f8") ) (segment - (start 132.45 96.1) - (end 132.625 96.1) - (width 0.2) + (start 122.62 106) + (end 122.625 105.995) + (width 0.3) (layer "F.Cu") (net "GND") - (uuid "588e0801-0423-4d5c-bd5c-8609f6a9210c") + (uuid "2601b535-7840-4378-86bc-f820194b84c2") ) (segment - (start 123 73.2) - (end 122.7 73.5) + (start 145.395 121.68) + (end 142.73 121.68) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "62ef99ca-37aa-4d7f-8e7e-13acb38d2707") + (uuid "26c06beb-08fe-491f-b602-f978692a23c5") ) (segment - (start 145.525 103.175) - (end 145.75 103.175) + (start 125.8 124.12) + (end 126.28 124.12) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "648bf284-45d9-4715-8a9b-78968fd1c715") + (uuid "27bdb106-4a23-4e75-9f02-216d2c8723a5") ) (segment - (start 142.55 96.1) - (end 142.8 95.85) + (start 146.448529 83.5) + (end 146.248528 83.299999) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "670bb992-8cbd-4e28-bb81-608b94cea068") + (uuid "2b93e730-6dea-46b7-ad88-4c0a407e7433") ) (segment - (start 123 126.25) - (end 123 127) + (start 145.3 104.475) + (end 146.175 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "693e6fdc-76ec-497e-a7c9-e2916c973c9f") + (uuid "2c1a7334-6b75-4906-a0c8-e26b61b4f56e") ) (segment - (start 148.2 83.2) - (end 147.6 83.2) + (start 146.075 116.575) + (end 146.075 112.425) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "696edf4e-b607-4ba2-9da8-47d867da6417") + (uuid "2e12426c-a4f1-4e54-a16e-943e70fe5528") ) (segment - (start 137.6 103.9) - (end 137.85 104.15) + (start 132.925 103.6) + (end 132.33 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6977403c-2d50-4c9f-b367-f5ef4bc36407") + (uuid "2f0e78cc-30e8-4760-82e3-dfd920d033af") ) (segment - (start 131.475 108.85) - (end 131.475 108.325) - (width 0.3) + (start 138.15 110.85) + (end 136.5 110.85) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6a72e318-b30c-477e-a3a7-9779e164fd29") + (uuid "2f621fca-fd46-4ccd-8a71-f033b91f2824") ) (segment - (start 132.199999 96.1) - (end 131.8 96.5) + (start 138.15 110.85) + (end 138.15 112.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6a754f51-2d4f-4ce5-b9ed-2a802a569b09") + (uuid "377a01a7-628f-4803-9ff1-71ea6c706f02") ) (segment - (start 133.45 122.4) - (end 133.75 122.7) + (start 122.625 105.1) + (end 122.625 104.025) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6af279d8-bacf-4443-93f6-8c2d420ba080") + (uuid "3a4fce48-0fba-4f69-83f9-021aa0c6b3f7") ) (segment - (start 121.75 115.5) - (end 121.75 114.5) + (start 129.38 103.29) + (end 129.38 102.438924) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6cc236c9-8ab8-485d-b0c0-d6c35874bb10") + (uuid "3d87378e-78fa-410f-a3de-5c29ccd905bc") ) (segment - (start 122.85 124.9) - (end 122.6 124.65) + (start 132.925 96.225) + (end 132 95.3) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "6d5256e7-5060-40ac-bc24-5ec45bd89d8e") + (uuid "3e59ca58-2c8f-4e44-8edf-6000d398998d") ) (segment - (start 128.5 103.3) - (end 128.75 103.05) + (start 129.5 105.5) + (end 127.975 103.975) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "72c8eca1-a9f9-4c70-86e5-3948340cb79b") + (uuid "3fa57c29-d8f7-409e-b9d2-0568f088bdc8") ) (segment - (start 140.525 122.275) - (end 140.45 122.35) + (start 123.9 83.5) + (end 124.1 83.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "7585cc33-fbdf-4bd5-aead-2bf04b3bd4b1") + (uuid "461652f4-1758-4f10-8269-bfaadc36bb68") ) (segment - (start 128.23 123.78) - (end 128.23 123.75) + (start 138.17 69.77) + (end 139.1 70.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "77cf6ab7-8768-4088-a475-cdd186c928f5") + (uuid "4c836664-ffd0-4bed-a755-0991af1de7cc") ) (segment - (start 136.6 95.6) - (end 136.3 95.3) + (start 131.8 102.67) + (end 131.8 100.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "7a879728-ca8b-4efb-8133-8f98d2ab1788") + (uuid "52b3415e-4d85-4143-a55c-901bb50ec3a3") ) (segment - (start 128.5 96.1) - (end 128.275 96.1) + (start 134.85 112.5) + (end 134.85 114.15) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "7d619c8e-703b-4188-863d-29e2d0306fd9") + (uuid "53912cde-16d4-48bf-952b-45a1f701cbe5") ) (segment - (start 123.3 96.1) - (end 123.05 95.85) + (start 146.175 96.4) + (end 146.5 96.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "7ee0fd30-be77-4d07-887e-6aeb2c918e72") + (uuid "54b62259-e810-4c40-96bf-daf51c5fc817") ) (segment - (start 142.675 103.175) - (end 142.45 103.175) + (start 147.3 83.5) + (end 146.448529 83.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "8009d297-c19a-406b-ad03-9c25fb914e04") + (uuid "588750ca-4d4d-4b4c-9695-4621a417a562") ) (segment - (start 137.5 104.025) - (end 137.075 103.6) + (start 141.6 105.5) + (end 143.5 105.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "82aeb622-4c3d-4500-9314-5eb71b23e96c") + (uuid "5e8761bc-9d81-47fe-8b39-b3c206709a5b") ) (segment - (start 122.75 125.9) - (end 122.6 125.75) + (start 138.15 114.15) + (end 139.55 114.15) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "83a834cf-f970-4092-b00e-7e96f0ebf59b") + (uuid "5f0de9b7-91e9-4a76-a6b3-faafbfebfaa9") ) (segment - (start 137.075 96.325) - (end 137.075 96.4) + (start 128.1 126.4) + (end 128.6 126.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "83c1dbff-d70a-4183-8340-0e2ddd0fd062") + (uuid "5f9407b2-39d6-4d51-9cfb-7683de4b29de") ) (segment - (start 137.725 104.025) - (end 137.5 104.025) + (start 143.775 105.225) + (end 143.5 105.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "885a4802-1624-4f34-ab6f-60e3171ae93d") + (uuid "5fe2ba25-a8b4-436b-884e-b1eed19d2651") ) (segment - (start 132.3 104) - (end 132.525 104) + (start 126.41 125.500552) + (end 127.309448 126.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "8c556036-d197-4a19-aa04-07de9860fba2") + (uuid "6008df83-907a-479a-b19c-d00ee96e6ef4") ) (segment - (start 123.175 103.175) - (end 123.4 103.175) + (start 133.595 123.105) + (end 132.68 124.02) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "8e062831-2159-47f1-a712-2d8e780c7cab") + (uuid "61e45a31-2f63-4153-93b8-a16bd2f64d26") ) (segment - (start 140.65 108.6) - (end 140.5 108.6) + (start 134.85 110.85) + (end 136.5 110.85) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "90b6494e-1340-4d1d-a5f5-41316cf56989") + (uuid "63178eae-cab6-4632-8eec-a9ec02da272e") ) (segment - (start 121.75 116.295) - (end 121.77 116.315) + (start 143.5 114.2) + (end 142 114.2) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "9186a08a-649c-4777-8126-dfbe21306212") + (uuid "689b03fb-dd44-4932-ac68-f561fd2da11d") ) (segment - (start 122.625 105.4) - (end 122.9 105.675) + (start 129.5 105.5) + (end 130.7 106.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "94dd97b4-b08b-416b-b1c1-8885c82ac3e9") + (uuid "6c0afcb3-567e-45a7-93b4-997fa940009f") ) (segment - (start 122.85 124.9) - (end 123.12 125.17) + (start 123.825 96.4) + (end 124.6 96.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "965ed9ed-53c4-4d0b-8988-7e85ad2529f7") + (uuid "6d1eb9ab-2bed-44f4-bf29-73c0536bc41c") ) (segment - (start 122.75 126) - (end 123 126.25) + (start 145.3 105.225) + (end 145.3 104.475) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "96bcb211-3364-4211-b759-cf3a83eff2bb") + (uuid "6eeeaccf-23ae-4b7c-96cc-dccff30fab3c") ) (segment - (start 148.35 73.2) - (end 148.5 73.05) + (start 137.5 67.2) + (end 134.9 64.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "98f2d86f-b205-41c3-9438-7f4c3b1a3340") + (uuid "6f7a54c0-42b9-4ec0-a258-d37b476f5aeb") ) (segment - (start 135.15 106.725) - (end 135.25 106.825) + (start 138.15 112.5) + (end 136.5 112.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "99b54e32-1e54-4978-b02d-18f45fe0efb3") + (uuid "700a002c-88d5-4dab-8e73-7eda31e555a4") ) (segment - (start 140.4 122.4) - (end 140.45 122.35) - (width 0.2) + (start 122.92 106.3) + (end 122.9 107.35) + (width 0.3) (layer "F.Cu") (net "GND") - (uuid "9d18a7f7-b865-48b9-95fa-fe7983a995c7") + (uuid "73e5446f-76e0-47a7-8de9-94580f3574d2") ) (segment - (start 131.4 117.915) - (end 130.8 117.915) + (start 122.625 104.8) + (end 123.825 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "a1f081e8-d8cd-46db-b411-6fd767d09e8c") + (uuid "75562d0b-6c0c-445f-af28-74968592c529") ) (segment - (start 131.45 117.865) - (end 131.4 117.915) + (start 144.175 116.575) + (end 143.5 115.9) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "a5d472ba-ac38-4506-a0ee-049c357704a9") + (uuid "7b9af617-677f-42b4-85eb-a3d9b3bc0623") ) (segment - (start 122.75 126.1) - (end 122.75 125.9) + (start 135.9 96.4) + (end 135.25 95.75) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "a745f4e0-9b33-4945-9dd1-c9288dad18df") + (uuid "80141c28-df33-4ee9-8651-350d026694ad") ) (segment - (start 134.25 106.725) - (end 135.15 106.725) + (start 128.349799 95.084604) + (end 128.349799 95.470835) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "a769e52a-d249-433f-b0dc-3fd0f52d1be3") + (uuid "8053cbe2-fe58-4b88-8e57-27700b658639") ) (segment - (start 145.65 103.3) - (end 145.4 103.05) + (start 140.75 119.5) + (end 140.75 118.85) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "a80b66de-0229-4610-bd7a-4a5b4b8a5e91") + (uuid "81918d08-dab7-4618-9812-1cb3a0912023") ) (segment - (start 125.75 118.315) - (end 126.75 118.315) - (width 0.3) + (start 122.7 83.5) + (end 123.9 83.5) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "aa4576dd-be23-4dd2-92da-a46babf91971") + (uuid "831d585e-4e5f-4196-b034-3bf972d821ce") ) (segment - (start 121.77 116.515) - (end 121.77 115.52) + (start 141.165 124.02) + (end 140.25 123.105) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ab4129b8-5a51-4f42-b503-db961ce2e8d7") + (uuid "83cbea98-2061-4632-ac8a-f4e3c63a9a5f") ) (segment - (start 131.45 117.565) - (end 131.45 117.865) + (start 127.309448 126.4) + (end 128.1 126.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ac6fdea4-b2e3-4f18-805a-d2b1945d5c03") + (uuid "8b3e0102-7de7-43de-891a-57793e1b782a") ) (segment - (start 136.65 119.215) - (end 136.25 118.815) - (width 0.3) + (start 123.599999 73.5) + (end 124.2 72.899999) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ad9491bc-b157-4a24-8cb7-7cc6b2375046") + (uuid "8c028727-f086-40b8-a98a-5e2e27c4bdc1") ) (segment - (start 132.525 104) - (end 132.925 103.6) + (start 136.5 114.15) + (end 138.15 114.15) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "b018d312-2914-45f7-8c55-9aea02dcced0") + (uuid "9275cf46-c5e7-40f7-839f-902b370243e2") ) (segment - (start 136.6 95.85) - (end 137.075 96.325) + (start 134.85 114.15) + (end 136.5 114.15) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "b18b1c36-bf65-49c5-bef4-817216858ebb") + (uuid "931a58ce-1549-4694-86e9-8843408556a5") ) (segment - (start 123.6 73.2) - (end 123 73.2) + (start 130.7 106.7) + (end 130.8 106.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "b277d948-52b3-421f-94a3-9050692eff79") + (uuid "9b48fa05-d505-443b-888d-f4605e751ccd") ) (segment - (start 130.2 119.185634) - (end 129.870634 119.615) + (start 147.3 73.5) + (end 146.1 73.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "b4cd90f9-2bf6-4c7f-b4f3-042145f81875") + (uuid "9b97e10e-c26c-482c-aeaf-c39310b4df01") ) (segment - (start 135.15 116.815) - (end 135.75 116.815) + (start 122.62 106) + (end 122.92 106.3) (width 0.3) (layer "F.Cu") (net "GND") - (uuid "b7e56207-bf76-4471-ac73-9846d3ea6b07") + (uuid "9df168af-8f35-45e5-a21b-01cfc4ff4eaa") ) (segment - (start 131.475 108.325) - (end 130.95 107.8) - (width 0.3) + (start 134.85 110.85) + (end 134.85 112.5) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ba3debd3-e694-40e1-a145-fc5cf39d791d") + (uuid "9f1a6c6b-43cc-45f2-acb0-fa3a9720195a") ) (segment - (start 128.275 96.1) - (end 127.975 96.4) + (start 122.7 73.5) + (end 123.599999 73.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "c1a90137-4134-41bb-8f58-81225bfddd21") + (uuid "a0205937-bbdb-44ec-b5e4-e62a733be407") ) (segment - (start 123.12 125.17) - (end 123.12 125.2) + (start 122.625 104.025) + (end 122.6 104) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "c21976ef-db3c-4258-87e0-d1db2d2fe434") + (uuid "a2ffa20d-4685-4e96-8451-39cbbc4c9d6d") ) (segment - (start 132.26 119.345) - (end 132.25 119.355) + (start 133.75 123.105) + (end 133.595 123.105) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "c278adf9-4b8b-4c8a-9c4e-30f9189f30b3") + (uuid "a3e63b77-eab4-4dd1-97bf-7a4f549c0d39") ) (segment - (start 147.6 83.2) - (end 147.3 83.5) + (start 141.495 103.07) + (end 142.025 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "c6ae191c-5222-4537-88aa-a7efdd531f52") + (uuid "a3f9cfbc-af97-4924-99f8-e7e106d018a6") ) (segment - (start 130.2 118.628603) - (end 130.2 119.185634) + (start 127.975 103.975) + (end 127.975 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "c8cfd978-a207-425c-80d6-9a5e71eaca44") + (uuid "a4292957-9aca-4db4-b4a8-024dd9cf86a2") ) (segment - (start 130.15 126.05) - (end 130.4 126.3) + (start 145.3 105.225) + (end 143.775 105.225) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ca5a39a7-2605-45ca-8ff7-b23f0dfafa3b") + (uuid "a54e7a1d-5a10-4b4d-8437-e94cc811e891") ) (segment - (start 130.2 118.001397) - (end 130.2 117.244366) + (start 143.5 119.5) + (end 143.5 105.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "cb28836c-ee3e-4d0e-b4ec-e24a10333a94") + (uuid "a9185d7c-5c13-4fae-b597-a71ef757b070") ) (segment - (start 142.45 103.175) - (end 142.025 103.6) + (start 129.38 102.438924) + (end 129 102.058924) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "cbb49b95-86e4-4481-afef-6aa018ec1699") + (uuid "a9fa0e7b-618a-43f9-bebf-7639faf552e8") ) (segment - (start 132.625 96.1) - (end 132.925 96.4) + (start 129 100.6) + (end 128.7 100.3) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "cc49a91e-402e-4ca7-89ec-506c31a63f72") + (uuid "aa2ced4b-b624-42a7-8bde-f26dde9dbd75") ) (segment - (start 133.75 122.7) - (end 133.75 123.105) + (start 139.9 119.5) + (end 140.75 119.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ccab7cd9-4af4-4f98-bd70-7e53271e6c62") + (uuid "aabf44ae-b26b-4266-8d92-ca42d3a279dd") ) (segment - (start 133.449999 122.4) - (end 133.199999 122.15) + (start 142.025 96.4) + (end 146.175 96.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "d26b47fa-e69c-49b4-bb71-ecd6990ee18e") + (uuid "b1326e98-b6ab-42b7-bc6c-17f8ea71ae7a") ) (segment - (start 128.55 96.1) - (end 129 96.55) + (start 122.625 105.1) + (end 122.625 104.8) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "d3408ede-93df-4e67-b597-5f4c72ab3167") + (uuid "b58db6e2-8f77-4370-9879-88b64b616e93") ) (segment - (start 147.6 73.2) - (end 147.3 73.5) + (start 123 127) + (end 123 125.32) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "d5aaa67d-0fcf-439b-9db7-1cbeaf0a70c1") + (uuid "b98f9d2d-fd24-4ec6-9738-453bc5959f5e") ) (segment - (start 148.35 83.2) - (end 148.5 83.05) - (width 0.2) + (start 122.625 105.995) + (end 122.625 105.1) + (width 0.3) (layer "F.Cu") (net "GND") - (uuid "d8331505-bf23-4a0c-87fa-18feed3e56ae") + (uuid "baa96635-41ad-4ada-9f60-03844f5be26f") ) (segment - (start 145.65 96.05) - (end 145.825 96.05) + (start 146.775 120.3) + (end 145.395 121.68) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "d85e525c-a1f8-4af8-8391-efc9aa9d15e1") + (uuid "c19859c1-93d4-48a2-84e5-28b25e812d79") ) (segment - (start 123.6 73.2) - (end 123.95 73.2) + (start 141.32 124.02) + (end 141.165 124.02) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "d900e927-3f9b-4800-84db-cda62d8511ab") + (uuid "c5388644-9549-41cb-9afe-267a2aab0dff") ) (segment - (start 131.4 117.515) - (end 130.8 117.515) + (start 140.6 101.12) + (end 140.6 100.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ddf60194-39dc-4f03-a4e2-37db8845a577") + (uuid "c94003a4-e3be-4d51-a1d1-905aa0b111a1") ) (segment - (start 130.15 126.05) - (end 129.65 125.55) + (start 140.75 118.85) + (end 140.6 118.7) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e2ee8d14-6246-4757-b23f-123cd62e277c") + (uuid "cadafb61-c5a7-478e-9c98-d1bc157f084a") ) (segment - (start 142.45 95.975) - (end 142.025 96.4) + (start 131.57 102.84) + (end 131.6 102.87) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e433646b-2012-45b4-a7c5-549045803487") + (uuid "cba42879-973a-435c-a763-a4ddfb661117") ) (segment - (start 122.85 119.315) - (end 121.75 119.315) + (start 128.349799 95.470835) + (end 127.975 95.845634) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e4486ab8-9450-4df7-b44f-68e6409ad4d6") + (uuid "ce5615cb-a174-487f-8d8e-5833f7ec080b") ) (segment - (start 122.9 105.675) - (end 122.9 106.125) + (start 127.975 95.845634) + (end 127.975 96.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e4b030be-167b-4ba3-9566-1d1d33f9150f") + (uuid "d32aac12-b259-4962-b41b-c958eb1c9532") ) (segment - (start 133 119.265) - (end 132.72 119.345) - (width 0.3) + (start 122.5 125.2) + (end 123.12 125.2) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e4e7064f-9e9c-4cab-a110-8c872d9062ae") + (uuid "d3620437-55a1-4734-98ca-90dadf03dbc5") ) (segment - (start 128.5 96.1) - (end 128.55 96.1) + (start 137.075 96.4) + (end 135.9 96.4) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e6a5ac7f-0bce-4155-b774-49b6d31e4048") + (uuid "d6d44c11-f434-46e1-aae1-73293460d3a3") ) (segment - (start 129.886397 118.315) - (end 130.2 118.628603) + (start 126.28 124.12) + (end 126.9 123.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "e90bb0c2-c06d-44d9-b4d1-47698b892dc3") + (uuid "d8655bf2-feb4-40e8-8875-901b32d5a5f4") ) (segment - (start 135.75 116.815) - (end 136.25 117.315) - (width 0.3) + (start 140.6 100.5) + (end 140.4 100.3) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "eb24beda-682d-4858-a6b3-c361d2c1f696") + (uuid "d9b15a1a-eb31-471b-a380-344f6ffb6318") ) (segment - (start 121.77 119.295) - (end 121.75 119.315) + (start 136.5 114.15) + (end 136.5 112.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "eba69479-fd48-4106-a89f-aeb455a403c3") + (uuid "dcbf3436-71c0-49cf-a481-ccebbf4a996e") ) (segment - (start 142.675 95.975) - (end 142.45 95.975) + (start 138.15 114.15) + (end 138.15 112.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "ec7d56b9-2d54-4107-9fbb-2105f2315f38") + (uuid "dd3022d6-ab9d-4e39-8c71-9004f6f081dd") ) (segment - (start 121.77 116.515) - (end 121.77 119.295) + (start 146.175 103.6) + (end 142.025 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f0badbb5-a58f-4453-a06e-5fe9030c2567") + (uuid "de8bf8f0-4e73-4a31-abe7-da62d4f2ec7b") ) (segment - (start 148.2 73.2) - (end 148.35 73.2) + (start 129 102.058924) + (end 129 100.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f4052e91-9b8d-40ec-937b-440fe3fcbb88") + (uuid "e30cf8fd-78bc-443a-8527-a53bdb17815a") ) (segment - (start 139 114.3) - (end 137.45 114.3) - (width 0.3) + (start 124.2 72.899999) + (end 124.2 71.8) + (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f4dc802b-6c59-4fa9-8b55-ac0ca29d50c3") + (uuid "e9767679-238f-4306-a28a-e6a25eb31acb") ) (segment - (start 128.5 124.05) - (end 128.75 124.3) + (start 132.925 96.4) + (end 132.925 96.225) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f8080b9e-b979-4977-b7b5-8aac62b55141") + (uuid "ed59e589-927e-4d10-a384-9557561f9c6e") ) (segment - (start 128.5 124.05) - (end 128.23 123.78) + (start 128.6 126.4) + (end 129.65 125.35) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f8523fce-63bb-4498-8c08-b995a84ab5fa") + (uuid "ee8115fd-ef88-4f32-85c2-e58943306d9e") ) (segment - (start 145.75 103.175) - (end 146.175 103.6) + (start 137.675 103) + (end 137.075 103.6) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "f856904b-4bbd-4212-aabe-f387f667952b") + (uuid "ef715771-eb96-4d34-95a8-7b091ac9e8d6") ) (segment - (start 129.886397 118.315) - (end 130.2 118.001397) + (start 139.55 114.15) + (end 139.6 114.1) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "fa42ef2f-456b-4245-a663-df5a35ad9ebe") + (uuid "f45d10a4-9bf0-4b69-8198-fca880f1c647") ) (segment - (start 130.2 117.244366) - (end 129.770634 116.815) + (start 140.75 119.7) + (end 140.75 119.5) (width 0.2) (layer "F.Cu") (net "GND") - (uuid "fe32d0e1-bdb6-4d35-ab66-310b22897cb1") - ) - (via - (at 144 94.5) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "008d76bd-da30-4071-8664-f917f89118d5") - ) - (via - (at 131.8 124.35) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "0420f3d5-501f-4aa7-8355-4113fef62618") - ) - (via - (at 130.449999 67.55) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "056956fa-b9e2-40a1-8642-fff0f5a1f9aa") - ) - (via - (at 143.75 70.55) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "08e73058-12f9-4f68-8054-70ce686d489a") - ) - (via - (at 123.95 83.2) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "0914a0c1-be82-44a6-9ab4-4f6e6779e255") - ) - (via - (at 121.3 107.15) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "0fc77bcd-8955-4a72-aa86-1af7f2409b24") - ) - (via - (at 142.8 95.85) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "1073f531-8c67-4bfd-b722-b91fa0e42510") - ) - (via - (at 139.1 103.7) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "13451eb3-c290-47e6-a345-f21fe6155f88") + (uuid "faf32a77-488e-48f9-aa36-a6ff517c2033") ) - (via - (at 122.35 105.15) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") + (segment + (start 130 103.91) + (end 129.38 103.29) + (width 0.2) + (layer "F.Cu") (net "GND") - (uuid "15dc7502-470b-400b-909b-d7a130a8ce63") + (uuid "fe77ae0e-33f6-496f-821b-4ade8c9a8fd6") ) (via - (at 131.8 96.5) + (at 140.6 118.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "1648edd5-86cf-46b1-8e76-d62cb818eaf4") + (uuid "0d8e0891-710a-4ec5-8591-7cdfc810050e") ) (via - (at 136.3 95.3) + (at 126.9 123.5) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "1716c09e-a87d-4b8c-9192-ebd8c69d4b3e") + (uuid "12119435-7aa7-4015-995b-70cfe8066c03") ) (via - (at 121.75 119.315) + (at 128.3 97.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "177c5b18-eca6-4e35-8e02-19b3a267bab7") + (uuid "1c688f0d-3f94-4d00-8dd5-ee2f2004ced1") ) (via - (at 122.6 125.75) + (at 128.7 100.3) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "19ab2e2a-e848-44f1-9b49-0a797b8d5257") + (uuid "232a270a-6e2e-4413-896f-b830723cf663") ) (via - (at 128.75 124.3) + (at 139.6 114.1) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "21fc01ff-75e3-4145-900c-73bbc56d47ee") + (uuid "274b0ded-0084-42fd-84da-3d36c677b3f1") ) (via - (at 123.15 85.6) + (at 130.85 97.425) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "22406884-4d96-4d58-9763-6d28058ba584") + (uuid "3358c26c-1470-4541-b387-ad39b6207100") ) (via - (at 123.05 95.85) + (at 130.7 63.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "2581e767-f8d6-43a8-ab3f-a629cdc48576") + (uuid "3a258ea2-e474-4ca9-aade-8fb8ffcc5ad2") ) (via - (at 140.5 108.6) + (at 139.1 70.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "2906bf46-fa0e-4b69-9dd5-b54b8f3cde9d") + (uuid "3d050a78-bd2c-42c7-871c-230d15ff85f7") ) (via - (at 128.75 103.05) + (at 132.5 67) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "306e0df2-8be3-4865-8e9d-20e812ec0ce3") + (uuid "41a82774-773e-4cd7-9425-f48821c254aa") ) (via - (at 122.6 124.65) + (at 145.4 88.1) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3168a006-6b12-4a3e-9b37-ab5e8a4dec74") + (uuid "506688d1-6734-4169-a24b-607b5109c0b2") ) (via - (at 146.5 67.45) + (at 137.5 97.75) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "319e94fa-2873-4ab8-8386-9175a99c0638") + (uuid "51ead269-7330-4243-bee3-5887a6cc3d26") ) (via - (at 135.25 106.825) + (at 135.25 97.25) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "368fd85f-300e-41d2-9454-5c9175f2b4a7") + (uuid "6047ed51-b19a-4a4e-b285-fb08116a4e3a") ) (via - (at 140.8 122.15) + (at 124.2 71.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3860d784-f05c-4daa-9d37-4b4b5fa26907") + (uuid "60a34284-a277-48fe-b33c-25426f89a8d2") ) (via - (at 142.85 95) + (at 134.9 64.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3c24c6ab-118c-480a-b65b-a8604b37a3be") + (uuid "643e7b59-6300-4de3-8ffe-08166c4fc0c1") ) (via - (at 136.25 117.315) + (at 147.05 96.95) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3ca8e5a2-e5a0-4ab6-b3fa-cbf54a71a4e2") + (uuid "792e50b7-b21a-402e-929e-49e2fd0e3f5d") ) (via - (at 134.6 103.7) + (at 146.248528 83.299999) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3cd07b83-e6fd-4a80-96d4-2dbffb41d13d") + (uuid "7ab20cba-f102-4140-8827-0fbea56227bf") ) (via - (at 130.5 92.3) + (at 124.2 64.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "3dd4c2e1-3fb1-4a72-a337-a5abc4e45706") + (uuid "7d28cc66-bb91-4d19-a811-e5ad924f9731") ) (via - (at 129.870634 119.615) + (at 145.6 73) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "403a6b0a-b36d-4358-abdd-77e664e7d486") + (uuid "7f1b8762-1c5b-4229-94e8-5413a284ee4e") ) (via - (at 131.45 117.565) + (at 124.75 96.25) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "4167a3a8-d8a4-4630-bf15-e0e01f7c27d7") + (uuid "835b60df-74c1-402f-8ba4-9b30717629b0") ) (via - (at 145.3 75.1) + (at 131.3 117.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "425fb94f-688a-48d6-8e8f-2974db766b39") + (uuid "849fd1e4-f71b-4a34-995e-08e1094c484f") ) (via - (at 136.4 100.4) + (at 130.8 106.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "45748755-847f-4218-b922-da76fe03a243") + (uuid "a07a308f-9fe5-4a8c-a913-4a1dd322a0a3") ) (via - (at 140 69.4) + (at 122.6 104) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "48930b45-ecd9-4d0f-a9bf-6aa685733eb1") + (uuid "a4c405b8-df55-48a1-9f99-4c8901e05de5") ) (via - (at 134.7 63.95) + (at 142 114.2) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "4b9d30e2-ce41-4552-b52f-613ae2f70e36") + (uuid "a841e586-18e4-4f4b-bf54-a838df96022c") ) (via - (at 135.45 103.8) + (at 124.1 83.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "52b06599-cdbc-4d58-bad4-7f1c9a601b7c") + (uuid "aaa9f92e-065c-4f42-85c6-d64420946eac") ) (via - (at 137.85 104.15) + (at 140.4 100.3) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "588840a2-1be4-42ee-92c5-4dd2055cf6b5") + (uuid "ad8961f8-38f6-4753-b2a2-6b6bd32a6e3f") ) (via - (at 133 119.265) + (at 121.8 96.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "5c197731-dd68-4cc7-bd39-38f0b8dbdd90") + (uuid "affbf252-2905-474b-9263-0e4698ce2c9c") ) (via - (at 129 96.55) + (at 137.799998 103) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "6d0dbccc-176c-43ec-83d7-604db7a0821a") + (uuid "bfec290a-7ee3-4238-9caa-ac07b74d6353") ) (via - (at 148.5 83.05) + (at 135.25 95.75) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "76fb8447-47c8-40b6-90f4-44b60db679c9") + (uuid "d0610bc8-c248-4ec9-a1cf-48eb7d1a8dcb") ) (via (at 136.285 75.94) @@ -29688,7487 +30073,6543 @@ (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "85f3e0bd-69d9-47ef-96d3-57164dee98fe") - ) - (via - (at 144.55 69.35) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "88dd038d-c3dc-4fc3-b855-eaecbbf06e29") - ) - (via - (at 143.3 102.35) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "89caef22-d241-44e6-9ef6-3a4ad5809d80") - ) - (via - (at 143.2 90.65) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "8b6d083e-b85a-47a7-8fdb-f6517b4cf551") - ) - (via - (at 132.15 104.15) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "905dfc55-2afd-4a95-b2b5-c8103b1de927") - ) - (via - (at 130.449999 103.7) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "968650b7-be31-42ff-bf40-3328bb873109") - ) - (via - (at 141.7 70) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "96a2ea97-d71b-4e36-9420-50b40cd3a63e") - ) - (via - (at 137.4 125.8) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "98609760-3c6e-41bb-8d10-328ec2f7a5e1") - ) - (via - (at 123.95 73.2) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "a7428682-0b62-4530-abd5-ae864f8bfe53") - ) - (via - (at 137.45 114.3) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "a8bf82aa-663d-424f-99d1-12c8cea0bec3") - ) - (via - (at 129.770634 116.815) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "a929e067-df15-4f0c-8456-e5ee04313974") - ) - (via - (at 131.9 100.4) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "ad1efe8c-896d-4246-83ef-94dade9009de") - ) - (via - (at 144.95 110.7) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b05ff3b0-15fa-4815-845e-52818932548c") - ) - (via - (at 148.5 73.05) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b46a6c2f-bb8c-4d95-827d-e0d1b217bcb2") - ) - (via - (at 143.3 106.45) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b615da0f-857c-4738-82f1-f9b6f4bf3865") - ) - (via - (at 137.05 92.15) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b74b6841-5600-4291-a97a-852568503128") - ) - (via - (at 131.785 73.44) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b7c5ebc2-acfd-44e1-ae19-6a92f6cce486") - ) - (via - (at 142.8 103.05) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "b92a999b-da37-45c9-86be-ee20480e7dbb") - ) - (via - (at 136.05 101.25) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "bd8a0aa8-45d1-4c9e-a19a-1c58890f53bf") - ) - (via - (at 141.95 79.7) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "beba54c8-c68c-455b-9a3d-2d5fbb641a56") - ) - (via - (at 129.8 64.05) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "c297c740-bde4-4fc7-a60c-6588ef1c0e85") + (uuid "d3e5deae-b85c-4072-84e9-b078c1e14fc5") ) (via - (at 139.85 87.25) + (at 131.8 100.5) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "c65b1ea6-27bf-4f5b-8d02-8d882963a1bd") + (uuid "d8105788-0b02-4f81-960d-19a5b95e662b") ) (via - (at 145.35 93.1) + (at 128.349799 95.084604) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "GND") - (uuid "c6a67ff5-b33d-4213-a015-5ad2d51aca1b") - ) - (via - (at 130.95 107.8) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "ca97069f-9992-4c6e-86a0-57f2d11c5803") - ) - (via - (at 142.8 126.6) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "cbfe0c29-7e05-45b5-8cdb-ea8f7eb1ef29") - ) - (via - (at 146.35 66.599999) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "cf8671e1-78c6-418c-ba17-ddf444267764") - ) - (via - (at 145.45 95.8) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "d34cc7de-e6b8-4b22-8598-47a46fed6a52") - ) - (via - (at 134.55 101.25) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "d85d4d64-9812-412e-a241-7398a26cbf5f") - ) - (via - (at 147.45 106.45) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "d87ece67-efa5-4bbe-9c30-3575b9303605") - ) - (via - (at 123.05 103.05) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "d8da9ea5-e447-49ae-bb26-1b38d41ffab9") - ) - (via - (at 136.25 118.815) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "da1d6363-cd9a-43e6-b59e-8552106cb2d2") - ) - (via - (at 147.45 102.35) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "dc4bd33c-0bac-4c8d-abaf-15de755df988") - ) - (via - (at 142.9 67.4) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "dc6a5b63-1dce-463f-8bfd-305087dfc34b") - ) - (via - (at 145.4 103.05) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "de528d49-1f30-4483-9d78-f7a069a915f5") - ) - (via - (at 123 104.55) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "f4a49318-5020-43c6-931c-a47f6c9c85e4") - ) - (via - (at 133.199999 122.15) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "f4c47e56-ed9c-4a24-95e5-7a27f9fb8fa4") - ) - (via - (at 130.4 126.3) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "f4f4bcd3-9ecb-420a-b1a2-916a7da7e96b") - ) - (via - (at 125.75 118.315) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "GND") - (uuid "fb972903-e624-44f9-9a31-7063234286e1") - ) - (segment - (start 145.505 75.63) - (end 145.505 75.725) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "00ca20bd-d736-4176-ba4e-fd22833b331c") - ) - (segment - (start 136.8 91.9) - (end 137.05 92.15) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "0155947a-2bbd-43ee-a0c5-67c1a6884a32") - ) - (segment - (start 143.25 67.4) - (end 142.9 67.4) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "083a4d35-4558-4bb0-bf5a-a0021b2d8afe") - ) - (segment - (start 141.7 79.95) - (end 141.95 79.7) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "0b536283-5ca0-4c41-8f97-b6a531e622f5") - ) - (segment - (start 137.625 125.925) - (end 137.945 126.245) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "0b81cf1e-11f3-4327-bef9-38127b04434f") - ) - (segment - (start 147.75 106.65) - (end 147.65 106.65) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "0bef296d-42fa-49f2-9adf-992aab916a62") - ) - (segment - (start 132.225 100.4) - (end 132.525 100.7) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "0f85cf2b-248b-4e6e-a73c-2843b5fdc3d4") - ) - (segment - (start 141.825 79.825) - (end 141.825 80.24) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "108531eb-ef38-4558-82c7-ae865cdb48a4") - ) - (segment - (start 134.35 103.45) - (end 134.6 103.7) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "1087b0e7-d5a8-4b21-9879-2d747a39312f") - ) - (segment - (start 121.6 107.35) - (end 121.5 107.35) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "112b8364-0918-4322-929d-002b1c1400e9") - ) - (segment - (start 122.75 104.8) - (end 123 104.55) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "12ff3323-0e87-4a56-a9ea-6cdd4678e3b4") - ) - (segment - (start 144.15 94.65) - (end 144.18 94.65) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "16639e3e-331d-4d8d-80a6-fab344680520") - ) - (segment - (start 143.85 91.325) - (end 143.85 91.375) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "16e44137-3756-422d-bfe9-7a8d763c9569") - ) - (segment - (start 147.95 102.55) - (end 148.25 102.85) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "1db67c16-b224-41a0-b114-69773708d945") - ) - (segment - (start 146.1625 66.75) - (end 145.8625 67.05) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "21eeba2e-1e60-4208-a594-6480b54dc26b") - ) - (segment - (start 134.35 103.45) - (end 133.65 102.75) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "23b87beb-d91e-48c6-a8ef-d6a379306e42") - ) - (segment - (start 135.8 101) - (end 136.05 101.25) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "25597d9f-243c-40b7-a142-82096ae876ac") - ) - (segment - (start 144.3 94.8) - (end 144 94.5) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "257f1c45-c9bb-4c4d-9791-00a2cc60cbb9") - ) - (segment - (start 146.05 66.9) - (end 146.35 66.599999) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "26120ac7-d983-4d75-acb5-d16eeb9195e6") - ) - (segment - (start 145.2 75.2) - (end 145.3 75.1) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "26a8d4a9-31ea-4b5f-a8a0-25cf58763d84") - ) - (segment - (start 145.2 75.45) - (end 145.2 75.2) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "296cb927-6f86-4d3a-8ec9-d0149215eb8d") - ) - (segment - (start 130.75 92.05) - (end 130.5 92.3) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "2a723117-0350-4dab-8390-86b7e1cb8998") - ) - (segment - (start 143.4 90.875) - (end 143.85 91.325) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "2f2a177d-efb5-492e-9e6b-eb5940a320ec") - ) - (segment - (start 143.8 106.65) - (end 144.1 106.95) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "31422062-eba9-4237-b708-448761fa1860") - ) - (segment - (start 140.05 87.55) - (end 140.05 87.45) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "319f700e-d304-4e02-98dc-cb0c9668f109") - ) - (segment - (start 123.35 85.4) - (end 123.15 85.6) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "324f57ab-11ce-49d7-aedb-6d3fd50b51c7") - ) - (segment - (start 143.25 67.25) - (end 143.3375 67.25) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "35e3b751-dff1-4ee8-9d73-a88536cb4ae4") - ) - (segment - (start 122.75 104.9) - (end 122.75 104.8) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "36366900-c842-424a-ab34-b30115bfd93e") - ) - (segment - (start 142 94.55) - (end 141.65 94.9) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "3ad3cd54-671a-4569-b70c-f84df1a1db60") - ) - (segment - (start 129.925 67.425) - (end 129.5 67) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "3b91cc7c-e20b-4c42-b36a-d2dde986bc1b") - ) - (segment - (start 147.65 102.55) - (end 147.45 102.35) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "3b9e17f0-33d8-47fd-8b74-4c54778ba36b") - ) - (segment - (start 135 63.475) - (end 135 62.7) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "3d375821-e119-44e6-b5b1-98df7b63db58") - ) - (segment - (start 122.35 105.15) - (end 122.95 105.15) - (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "3e0ec951-e92e-43e5-8b5a-87225bca23f5") + (uuid "e7584c41-4d61-4109-bdaf-ded8b924dad9") ) - (segment - (start 143.4 90.9) - (end 143.4 90.85) - (width 0.2) - (layer "B.Cu") + (via + (at 132 95.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") (net "GND") - (uuid "44107c7a-230d-40a1-a770-02b9af22d11f") + (uuid "e9bb4459-3e62-463c-a45f-0bf5dc84451c") ) - (segment - (start 122.95 105.15) - (end 123 105.2) - (width 0.2) - (layer "B.Cu") + (via + (at 131.785 73.44) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") (net "GND") - (uuid "44cf3092-3a91-4c53-96fc-339d1b5f8992") + (uuid "ee46e023-f9cd-494d-89b2-b036f158a1a7") ) - (segment - (start 144 70.3) - (end 143.75 70.55) - (width 0.2) - (layer "B.Cu") + (via + (at 122.5 125.2) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") (net "GND") - (uuid "482853eb-0d05-4414-acd5-4b8265631ed4") + (uuid "fc48cd95-8c8c-4d70-bb16-7cdbb0df4e43") ) (segment - (start 130.699999 103.45) - (end 130.449999 103.7) - (width 0.2) + (start 138.025 97.225) + (end 137.5 97.75) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "4c870d54-a6a9-4428-a37c-c349049a4a71") + (uuid "0039d49b-1814-4406-a4e8-7dc5905c7dfa") ) (segment - (start 138.85 103.45) - (end 138.15 102.75) + (start 130.45 96.7) + (end 130.4 96.65) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "4da6fbbf-8653-4c55-baa2-2ff7e73b8fe9") + (uuid "004ccd97-3335-4f54-962f-9bd94967b8d5") ) (segment - (start 147.75 102.55) - (end 147.65 102.55) + (start 142.285 127.235) + (end 141.32 128.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "503ad8da-a0a2-4c61-b533-76db86ddb3bf") + (uuid "0132aef0-f533-4451-9ce2-12d9f5724c44") ) (segment - (start 145.3 110.6) - (end 145.665 110.965) + (start 132.475 123.815) + (end 132.68 124.02) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "519a7ffd-4f22-445c-9617-c8b6575ff4f4") + (uuid "073caa5c-02c5-42e4-872c-e3472f5e97f7") ) (segment - (start 131.55 124.1) - (end 131.285 123.835) + (start 130.775 97.425) + (end 130.4 97.05) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "51c94a77-09a4-4aae-80e9-a7c2e69830a0") + (uuid "0b4cff59-bd9f-407b-922d-e7d3a51fa917") ) (segment - (start 124.0613 85.015) - (end 124.061 85.015) + (start 130.0625 125.492124) + (end 130.0625 126.1) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "52aeac98-c071-4ad6-9825-321ab82fa369") + (uuid "0c836e2b-7393-491e-aa33-64a780d24e35") ) (segment - (start 147.65 106.65) - (end 147.45 106.45) + (start 137.945 126.245) + (end 139.365 126.245) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "536bef22-7eb7-4476-94e5-93fcc378461f") + (uuid "0e422a48-9f27-44eb-a34d-434b61085fdd") ) (segment - (start 143.25 67.4) - (end 143.3875 67.4) - (width 0.2) + (start 132 95.3) + (end 131.72 95.22) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "53723352-3049-47db-a376-1f74ff398692") + (uuid "0e5c7f2b-2a07-46ab-a650-e41445fa4298") ) (segment - (start 135.2 103.45) - (end 135.2 103.55) + (start 129.015 129.11) + (end 129.0625 129.0625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "59c5d53a-e5b9-455c-a220-58eb45c1e5db") + (uuid "129d13d4-6a5c-458b-86e8-9e3bf6af28e7") ) (segment - (start 140.5 87.95) - (end 140.5 87.975) - (width 0.2) + (start 134.15 97.75) + (end 134.75 97.75) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "5a04ebf1-d85b-4bd5-98ca-4e39d171c60b") + (uuid "18de1e39-0f9c-4582-88ba-fa261d52a721") ) (segment - (start 147.95 106.65) - (end 148.25 106.95) + (start 130.0625 126.9375) + (end 130.0625 126.962932) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "5ae40574-6a17-403d-9d84-70718afda865") + (uuid "1a64040b-823b-4a09-8f67-31108b4dbc40") ) (segment - (start 123.35 85.3) - (end 123.35 85.4) + (start 129.5625 126.4375) + (end 130.0625 126.9375) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "5c4d6d24-d403-47b5-b53b-8eb1c98837ab") + (uuid "1aa14772-26ba-4f22-a254-1d674e98882c") ) (segment - (start 144.45 69.075) - (end 144.45 68.95) + (start 128.75 96.25) + (end 128.886397 96.25) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "5f530cba-5c6e-43ea-a9b6-71ba8a57fa83") + (uuid "1ec2915d-4434-4680-91fd-5ee350b6eb68") ) (segment - (start 145.8625 67.55) - (end 145.8626 67.55) + (start 129.65 125.35) + (end 129.35 125.35) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "60526fa9-a970-403f-8d57-1783e252e982") + (uuid "202995a2-2fed-430c-b6fe-2114af16fb9c") ) (segment - (start 135.2 103.55) - (end 135.45 103.8) - (width 0.2) + (start 134.75 97.75) + (end 135.25 97.25) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "63d443f9-c894-4990-84df-11c0366cf7ce") + (uuid "2cdf1f11-c682-4803-b132-63800992ca16") ) (segment - (start 141.445 80.24) - (end 141.834999 80.24) + (start 129.2 97.320634) + (end 129.2 96.563603) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "65290de1-5667-4e5a-aef1-68c5523c3e15") + (uuid "2db72a13-6f9e-4dd7-a566-7238aa09e45d") ) (segment - (start 144.35 68.85) - (end 144.45 68.95) + (start 142.285 126.065) + (end 142.285 127.235) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "6a4eaeb9-5526-41e0-b54b-e148c7a9cc22") + (uuid "301496d6-6d00-421a-8219-62e745b28ef1") ) (segment - (start 145.8626 67.55) - (end 146.1563 67.8437) + (start 129.5625 128.062068) + (end 129.862068 127.7625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "6c8b2eed-c6ce-4821-b429-f4323c6a9df1") + (uuid "323f7703-62f1-4111-8fe1-ee87f9051574") ) (segment - (start 123.35 85.35) - (end 123.726 85.35) + (start 123 125.7) + (end 123.925 125.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "6d138252-234e-4af7-a2c4-13cc47447796") + (uuid "39c803ea-ca89-4780-b3f4-0cf559a6e46d") ) (segment - (start 135.485 75.139999) - (end 136.285 75.94) - (width 0.2) + (start 139.24 101.51) + (end 139.5 101.25) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "6dbdf21f-fd28-4747-bd95-52d8ed486301") + (uuid "3ac62497-2376-4555-bde5-a09ad1fa9562") ) (segment - (start 144.4 68.9) - (end 144.3875 68.9) + (start 126.7 128.5) + (end 127.31 129.11) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "6e412f38-0f45-4b9c-bab4-a71c1ae7f168") + (uuid "3ea72fd3-12a1-4209-a7a1-0f3fdbc1162a") ) (segment - (start 145.3 110.6) - (end 145.05 110.6) + (start 121.26 99.75) + (end 121.26 101.25) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "70f38667-9371-4ef4-948e-26c16e4f6b21") + (uuid "3ea7ebc3-ee27-4730-9ee7-f159f3859dfd") ) (segment - (start 143.15 67.4) - (end 143.25 67.3) + (start 130.725 127.2625) + (end 131.7425 127.2625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "7313ad45-0d7f-4d22-8e4c-04d2ccd6f3bb") + (uuid "44b21185-4e2a-44be-97f3-38edf4734c98") ) (segment - (start 146.2 66.75) - (end 146.1625 66.75) + (start 141.445 80.24) + (end 142.97 80.24) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "755f4384-0105-4653-9d6e-d9bd6316eb82") + (uuid "470ca58f-2a33-47c8-b4d0-6454fc57ffe3") ) (segment - (start 141.825 69.875) - (end 141.855 69.875) + (start 128.7 101.224998) + (end 128.99 101.514998) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "7b6457fa-e2f6-48a8-a3da-bd04ded8f313") + (uuid "4819b84b-1d3a-4961-9864-efe03350b752") ) (segment - (start 131.4 102.75) - (end 131.4 102.7) + (start 121.28 97.22) + (end 121.28 98.25) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "7d186d7f-b227-494e-b873-edbbd02343b8") + (uuid "4b60419e-fce9-4907-a6ee-cbd4249b3dd2") ) (segment - (start 145.8 93.225) - (end 146.495 93.92) + (start 130.725 127.7625) + (end 132.2425 127.7625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "8119d1ae-2ea6-4462-8b0f-0ae792628cca") + (uuid "4ce85ce1-78c2-4365-8fa2-74aa31e46416") ) (segment - (start 146.1282 67.8718) - (end 146.0407 67.8718) + (start 121.28 98.25) + (end 121.28 99.73) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "8137f6aa-a035-4960-b1c4-c494d3a829fb") + (uuid "4d0a8cc6-8056-4665-8555-f8476780d6cd") ) (segment - (start 134.7 63.6) - (end 134.7 63.95) + (start 128.424998 100.3) + (end 126.45 102.274998) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "81490d7b-a00a-4c23-97c8-6a0b0127b63c") + (uuid "4dc12e78-a62f-42de-8c2d-7eacb7a73968") ) (segment - (start 129.28 64.57) - (end 129.28 64.6) + (start 124.25 64.75) + (end 124.2 64.8) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "81e809e9-72ff-43da-81e5-b4785a6ee981") + (uuid "4e648a34-4ba6-405c-bce3-625797ee61ae") ) (segment - (start 142.4 94.55) - (end 142.85 95) + (start 121.8 96.7) + (end 121.28 97.22) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "827dd99f-19b6-476d-9929-519b486d38be") + (uuid "4ff43e93-2afa-4052-9744-6b0d16fae0c8") ) (segment - (start 138.15 102.75) - (end 138.15 102.7) + (start 128.820634 97.7) + (end 129.2 97.320634) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "82e84d70-69a4-4aa2-9297-c6300099992d") + (uuid "50a8385d-2be0-4894-b838-8818b435fda4") ) (segment - (start 136.535 91.635) - (end 136.535 91.615) + (start 131.285 123.815) + (end 132.475 123.815) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "83cb6d71-d225-4bf5-b3ba-b20c64690acd") + (uuid "5182c38a-217d-4041-99ab-af8396ba692a") ) (segment - (start 144.2 68.7125) - (end 144.7 68.7125) + (start 129.920376 125.35) + (end 130.0625 125.492124) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "8493b5a7-11e1-464f-962a-b8e4a906c860") + (uuid "52db2165-d9a6-4dba-a932-c485e7c17a03") ) (segment - (start 130.325 67.425) - (end 129.925 67.425) + (start 145.505 79.225) + (end 143.73 81) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "851710e5-d705-4f8d-aac8-a1a77cee0691") + (uuid "561e34ee-f80c-49f5-a99a-4622d6c9d233") ) (segment - (start 131.774999 73.449999) - (end 131.785 73.44) + (start 130.85 97.425) + (end 130.775 97.425) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "851b2d49-bf89-4bbf-92b6-60b3db7e5cf3") + (uuid "57db6f1c-8778-45f6-a9dd-f0a261e17b70") ) (segment - (start 136.725 100.4) - (end 137.025 100.7) + (start 132.58 128.3) + (end 132.68 128.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "85d67375-3716-4b5c-bf6a-218889c4ff0b") + (uuid "58a0e908-c34e-4602-b72b-f405ebcd32eb") ) (segment - (start 143.5 102.55) - (end 143.3 102.35) + (start 129.2 129.2) + (end 129.5625 128.8375) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "86c16c52-a47e-4e14-830f-567b3c8db15a") + (uuid "5fa01654-4401-473b-9581-b6d9bd34141f") ) (segment - (start 145.05 110.6) - (end 144.95 110.7) + (start 129.2 96.563603) + (end 128.886397 96.25) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "86f2d42b-3426-431d-b197-6e99b77018a7") + (uuid "5fc3e28b-95c6-48ba-9408-cf87f73ea4d2") ) (segment - (start 145.6 93.35) - (end 145.35 93.1) + (start 130.85 97.425) + (end 130.45 97.025) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "880e73ee-bd7b-4597-82c4-a406f512712a") + (uuid "61764bc8-7bac-4497-aafc-2909d3b6e66b") ) (segment - (start 131.774999 74.44) - (end 131.774999 73.449999) + (start 128.7 100.3) + (end 128.424998 100.3) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "89f0c6ad-3360-43ac-8616-4bc7a7f4b180") + (uuid "61e6a30a-007b-49ee-876e-3771a9403b54") ) (segment - (start 135.525 100.725) - (end 135.525 100.7) + (start 132.5 67) + (end 134.9 64.6) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "8bef9986-a003-4fa0-8489-09b7c50018ce") + (uuid "6364d3ce-19b4-478e-8bc1-58e04e0619a8") ) (segment - (start 132.25 100.4) - (end 131.9 100.4) + (start 130.0625 126.962932) + (end 130.362068 127.2625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "8c048e36-ef54-4f3f-bacd-21e26c16bed7") + (uuid "67fecafe-5806-4550-9e5b-2d52320e468c") ) (segment - (start 147.75 106.65) - (end 147.95 106.65) + (start 124.06125 85.015) + (end 124.06125 84.414999) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "902028f0-609a-4a6f-9720-81c0825b092b") + (uuid "69c8c325-dd08-4686-afb8-17cd2310aab8") ) (segment - (start 138.85 103.45) - (end 139.1 103.7) + (start 125.5625 64.75) + (end 124.25 64.75) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "917ee7c6-fefb-42cd-b070-3ac74b6ea00a") + (uuid "6e28c456-d8ad-485c-8f6e-a33e5d1a1102") ) (segment - (start 136.75 100.4) - (end 136.4 100.4) - (width 0.2) + (start 138.025 96.7) + (end 138.025 97.225) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "948baf57-04c3-423b-8601-d37420a4e037") + (uuid "72c221ec-fa29-4260-99c6-934a0779bee8") ) (segment - (start 131.285 123.835) - (end 131.285 123.815) + (start 129.2 95.379366) + (end 129.2 95.936397) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "9494c6fc-88c4-4505-ad92-c050b011640b") + (uuid "72c69d0b-6a22-400f-a5f4-30f9a5c19d18") ) (segment - (start 146.1 67.9) - (end 146.45 67.55) + (start 130.362068 127.2625) + (end 130.725 127.2625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "956d6595-9643-4f46-aee6-364e147f2bed") + (uuid "72fcdcd6-9720-41d5-9ba8-44d09a2b475d") ) (segment - (start 143.4 90.85) - (end 143.2 90.65) - (width 0.2) + (start 139.5 101.25) + (end 139.5 101.2) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "973ccece-3d54-48b0-9b35-30641a904ae9") + (uuid "742f228f-c1b6-48c2-8d87-2539bd73de7a") ) (segment - (start 141.95 69.75) - (end 141.7 70) + (start 129.65 125.35) + (end 129.920376 125.35) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "9755b82a-0315-483d-936f-d99ccb73b22f") + (uuid "7458b2ce-80c8-4d14-8865-93bf8eea7bd7") ) (segment - (start 137.525 125.925) - (end 137.625 125.925) + (start 128.3 97.7) + (end 128.820634 97.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "9a68b489-d222-4209-941b-3c58b48256d9") + (uuid "7714f906-f829-4813-8811-ca6703d25c73") ) (segment - (start 143.6 102.55) - (end 143.8 102.55) + (start 135.485 74.889999) + (end 135.485 75.139999) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "9e770f40-9ced-46d4-b20f-aff7382681ed") + (uuid "78b94c6c-64e9-4012-b56d-09109dc2b9b3") ) (segment - (start 121.5 107.35) - (end 121.3 107.15) + (start 129.0625 128.425) + (end 129.0625 129.0625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "a1ae9a21-3db3-474e-a4d0-66c24a9602cb") + (uuid "7b8be8c6-720e-434d-b190-1aded8a3c666") ) (segment - (start 146.0125 67.4) - (end 145.8625 67.55) + (start 129.35 125.35) + (end 129.0625 125.6375) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "a3e4163d-7589-4c5b-ab9c-85a4411d10ac") + (uuid "7d3d07e5-b4fd-4c3d-9cb6-59a19debc074") ) (segment - (start 147.75 102.55) - (end 147.95 102.55) - (width 0.2) + (start 147.475 96.525) + (end 147.05 96.95) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "a6bd0af8-6cec-4d13-ae05-e84ebd04010c") + (uuid "7d50f0f7-e0c7-4349-bec7-994daf5e5a1c") ) (segment - (start 142.25 94.55) - (end 142.4 94.55) - (width 0.2) + (start 129.9 63.8) + (end 130.7 63.8) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "a6f9653c-bede-4808-a508-7f08911326c2") + (uuid "7e9b817b-6dec-4aee-941d-9d17dd3c4870") ) (segment - (start 140.05 87.45) - (end 139.85 87.25) + (start 139.365 126.245) + (end 141.32 128.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "a91a7a3f-13e4-4a73-bb83-fa6ba83700d8") + (uuid "86ffccd4-e1e9-49ea-b30b-bd365e152e9d") ) (segment - (start 144.55 69.175) - (end 144.45 69.075) - (width 0.2) + (start 139.5 101.2) + (end 140.4 100.3) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "a95dfb23-49a9-4868-b781-83f14a40b899") + (uuid "89f77e4b-0f5a-4228-8cba-0420abf4aa65") ) (segment - (start 145.2 75.325) - (end 145.505 75.63) + (start 130.0625 126.1) + (end 130.0625 126.9375) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "aa603399-5521-414a-a21d-5d6ee095ce2f") + (uuid "8bd886ca-c84b-4548-886d-87539b0591f1") ) (segment - (start 142.285 126.085) - (end 142.285 126.065) + (start 124.1 84.376249) + (end 124.06125 84.414999) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "b0c21e56-772e-402e-92a2-93127affef5b") + (uuid "9391631f-1bb3-4bca-8481-5601a32f3a4f") ) (segment - (start 130.75 92.05) - (end 131.02 91.78) - (width 0.2) + (start 131.72 95.22) + (end 131.25 95.22) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "b31f92ba-7fa6-46f6-ac9b-6b00686020d0") + (uuid "9466179c-bbf3-49ad-945a-daaccd8af553") ) (segment - (start 140.3 69.6) - (end 140.2 69.6) + (start 145.505 76.685) + (end 145.505 79.225) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "b4b22e31-d693-4673-b627-8be4d7e0a26d") + (uuid "947afe4a-4591-432b-82ff-dc6e63f8e64f") ) (segment - (start 143.8 102.55) - (end 144.1 102.85) + (start 127.31 129.11) + (end 129.015 129.11) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "b7f569ef-5399-46d9-8607-ead6f304c1b9") + (uuid "9904d180-7e4f-425d-ad09-9aec57b09075") ) (segment - (start 143.25 67.2) - (end 143.25 67.3) + (start 134.9 64.6) + (end 134.9 62.8) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "ba850126-8dde-4f9a-b0b1-157325d67d20") + (uuid "990e246a-87b8-4275-bec0-6177af453b3e") ) (segment - (start 142.55 126.35) - (end 142.285 126.085) + (start 121.85 96.65) + (end 121.8 96.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "bc140659-d6e4-49a2-b7d9-e28814ae4520") + (uuid "99ef0ce4-ec0b-4ed6-95c7-2e606a2d66d3") ) (segment - (start 135.9 102.8) - (end 135.9 102.7) + (start 128.36 126.1) + (end 128.16 125.9) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "bda8d508-9994-4575-98d8-04a5bad990f2") + (uuid "9dbb1b00-ab2c-4c11-ad93-7aa5b7857b6a") ) (segment - (start 146.15 67.4) - (end 146.45 67.4) + (start 130.45 97.025) + (end 130.45 96.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "be11151f-60ec-473c-ad35-2ef6e308a46a") + (uuid "9e93a472-cab2-4099-bf54-2a3007924eb4") ) (segment - (start 135.2 103.5) - (end 135.9 102.8) + (start 142.97 80.24) + (end 143.73 81) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "be5ab164-4cb6-4cdd-8748-b291ae937d41") + (uuid "9f229d99-6413-4d9b-af58-9b2306852bac") ) (segment - (start 144.3875 68.9) - (end 144.2 68.7125) + (start 147.2 96.95) + (end 147.05 96.95) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "bf686659-c83f-4964-88e2-1039f451b694") + (uuid "a43900e9-dbea-4580-b110-f71031349f4a") ) (segment - (start 141.7 70) - (end 140.775 70) + (start 131.774999 73.449999) + (end 131.785 73.44) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "c2ae4134-623d-4c59-9014-ebb87a456f26") + (uuid "a6421fd0-789f-48ea-9150-9abebebb64ee") ) (segment - (start 140.05 87.5) - (end 140.5 87.95) + (start 126.45 102.274998) + (end 126.45 103.6) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "c4be2efb-b156-4a34-8369-2bdd278ba017") + (uuid "a6e7a7fa-73ee-478d-9fb0-dfbb935db818") ) (segment - (start 141.855 69.875) - (end 142.25 69.48) + (start 121.28 99.73) + (end 121.26 99.75) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "c7ea236e-7d68-4215-b4d6-bdce95b1b9a3") + (uuid "a8f7e084-b5ab-47e2-88a9-9b588947b115") ) (segment - (start 142.55 126.35) - (end 142.8 126.6) - (width 0.2) + (start 124.75 96.25) + (end 125.75 96.25) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "c7f776a8-4805-43b4-aed6-da425ed09748") + (uuid "a9894572-3c37-459d-b5d6-0687d0eee10e") ) (segment - (start 144.18 94.65) - (end 144.555 95.025) - (width 0.2) + (start 135.65 95.35) + (end 135.25 95.75) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "c8b45eeb-d333-4cb8-82ca-4b43164de850") + (uuid "ad62aec4-cf96-4b20-bbe4-e65c925e4949") ) (segment - (start 143.3875 67.4) - (end 143.5375 67.55) + (start 129.2 95.936397) + (end 128.886397 96.25) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "cb6b06a4-2e30-4270-81ba-f71d103db5d9") + (uuid "ad89a4ba-b165-4330-9e43-4e776a186ca2") ) (segment - (start 143.6 102.55) - (end 143.5 102.55) - (width 0.2) + (start 138.525 101.51) + (end 136.61 103.425) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "cc858f65-84c3-49e1-9095-9842ddfe0757") + (uuid "b5ff22a5-196a-4dd5-b7ee-65a4a2c35eff") ) (segment - (start 145.475 93.225) - (end 145.8 93.225) - (width 0.2) + (start 146.5 89.65) + (end 146.5 89.2) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "ce157bea-0adf-487a-9db0-ba81f5290792") + (uuid "b995e0e2-43e3-4269-bcaa-2915fb7a3efc") ) (segment - (start 135.485 74.889999) - (end 135.485 75.139999) + (start 132.2425 127.7625) + (end 132.68 128.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "cf0771c1-adcb-4e90-be75-7d44c7bea12a") + (uuid "c0b37cc2-4e6d-40bd-97d8-4ae6a088a40a") ) (segment - (start 130.7 103.45) - (end 131.4 102.75) + (start 129.0625 129.0625) + (end 129.2 129.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "d1511fbe-1d54-4fc6-83f7-04d72fdfe153") + (uuid "c1a228d0-ba3a-4c6c-a570-4d30157059dd") ) (segment - (start 130.199999 67.3) - (end 130.449999 67.55) + (start 128.99 101.514998) + (end 128.99 103.6) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "d500da8a-a602-4243-9658-d15bf90213e4") + (uuid "c54735d3-b9e0-4221-a275-4a519f04bf36") ) (segment - (start 143.5 106.65) - (end 143.3 106.45) + (start 130.4 97.05) + (end 129.8 97.05) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "d7fd8f91-6d96-41dd-9018-ba806e9daea2") + (uuid "c596d09c-752b-41ef-b685-b26ff2058ace") ) (segment - (start 134.3 101) - (end 134.025 100.725) + (start 129.5625 126.1) + (end 129.5625 126.4375) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "dc3fe6da-cca7-476f-9af7-41fd6507ada8") + (uuid "c6fc0384-d911-48be-bf50-86443d9565bb") ) (segment - (start 129.55 64.3) - (end 129.8 64.05) + (start 135.285 76.94) + (end 136.285 75.94) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "dd362c3b-bca3-4c5b-9702-7b7cd6ae31d7") + (uuid "c8276b0b-988d-4d40-84d5-8a7bfaf1b2ad") ) (segment - (start 134.3 101) - (end 134.55 101.25) + (start 135.485 75.139999) + (end 136.285 75.94) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "de0a7fcd-fa6a-473a-9567-22bbcf1b4c9d") + (uuid "c8ed9f61-c3e1-400a-bda0-aae88703a93d") ) (segment - (start 131.02 91.78) - (end 131.02 91.75) + (start 128.7 100.3) + (end 128.7 101.224998) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "de2305a5-7e7d-4102-931c-522bf03e288b") + (uuid "ca96575d-d178-4663-b48c-b74ce04f314a") ) (segment - (start 135.8 101) - (end 135.525 100.725) - (width 0.2) + (start 146.5 89.2) + (end 145.4 88.1) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "dede4cdf-a7fc-4ed4-8d10-cc598a41a1a3") + (uuid "cd49bc6e-20f7-48ea-b128-899451628dfd") ) (segment - (start 137.65 126.05) - (end 137.4 125.8) + (start 129.5625 128.425) + (end 129.5625 128.062068) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e00202e5-b692-4f21-8a32-c28eaaf2ee6f") + (uuid "ce3b4dcf-5372-48f3-b98e-8e7de9cb99e5") ) (segment - (start 142.25 94.55) - (end 142 94.55) + (start 131.774999 74.44) + (end 131.774999 73.449999) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e07ab81e-1cba-4f76-98f9-b608de4a4674") + (uuid "cf8c710c-e2bc-49c8-b337-09346e748a03") ) (segment - (start 133.65 102.75) - (end 133.65 102.7) + (start 121.85 95.25) + (end 121.85 96.65) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e09c330f-4f4c-4f58-927e-84af3f0838ae") + (uuid "d67f4416-ba50-4f7b-9b02-3b90975370d9") ) (segment - (start 121.575 107.35) - (end 122.025 107.8) + (start 130.4 96.65) + (end 129.8 96.65) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e1306a9c-f597-477d-9303-613a9c5fd7bf") + (uuid "d842fe94-adbc-483d-87d5-41b7047e328c") ) (segment - (start 129.55 64.3) - (end 129.28 64.57) + (start 128.349799 95.084604) + (end 128.905238 95.084604) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e1ef175c-f0d4-467a-ae1d-f557ed0f76eb") + (uuid "dce473ae-6922-4428-a7db-7c6e3295428d") ) (segment - (start 136.8 91.9) - (end 136.535 91.635) - (width 0.2) + (start 138.525 101.51) + (end 139.24 101.51) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "e2e4841a-9b79-4a3e-9cd7-519bb1344ad2") + (uuid "dd200bcb-552b-4079-a3d6-c5c43f55f7e0") ) (segment - (start 140.775 70) - (end 140.75 70.025) + (start 128.16 125.9) + (end 127.68 125.9) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e3a1f46b-a0ca-4b50-9aa8-04f00435e226") + (uuid "df5d9f88-5229-45a9-88f4-271374f9cba5") ) (segment - (start 146.15 67.4) - (end 146.0125 67.4) + (start 129.862068 127.7625) + (end 130.725 127.7625) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e3d36d01-17ea-4e89-be3b-16e6175fdd65") + (uuid "e388da7c-4416-43bf-b82c-7c5b13630ea3") ) (segment - (start 144.55 69) - (end 144.55 69.35) - (width 0.2) + (start 147.475 95.75) + (end 147.475 96.525) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "e3d57426-f7cf-494d-9c33-51324eb2a252") + (uuid "e823caab-e6d1-423b-a6af-740a86dc9731") ) (segment - (start 144.27 70.03) - (end 144.27 70) + (start 131.7425 127.2625) + (end 132.68 128.2) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e5041f5c-0af0-4b40-b464-8173a04f091c") + (uuid "e9540da3-30f0-4c46-8b4e-10c46e57bf96") ) (segment - (start 146.45 67.4) - (end 146.5 67.45) + (start 129.0625 126.1) + (end 128.36 126.1) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e876e8fb-dfb5-43cc-b4af-c09b9aabaaca") + (uuid "ea07c5f4-4ad3-4f8a-ad9c-44e354f5d68b") ) (segment - (start 144 70.3) - (end 144.27 70.03) + (start 122.5 125.2) + (end 123 125.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e937cb00-b8bd-46b7-8b5b-68fbed99c629") + (uuid "eb4028e0-7950-4f73-b4b8-db69e8723576") ) (segment - (start 134.7 63.775) - (end 135 63.475) + (start 124.1 83.7) + (end 124.1 84.376249) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "e9c9be63-9613-479d-b75b-9a360afb783c") + (uuid "eb950ba8-269f-451c-bb84-03ba40d1a28b") ) (segment - (start 143.3375 67.25) - (end 143.5375 67.05) - (width 0.2) + (start 136.61 103.425) + (end 136.61 103.6) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "ea3930a0-3dd7-4ce1-ac97-41be0ed8b7dc") + (uuid "eedee06b-7802-4bc5-b90f-329124c8ad72") ) (segment - (start 135.285 76.94) - (end 136.285 75.94) + (start 129.0625 125.6375) + (end 129.0625 126.1) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "eff87001-4623-4192-b853-aad80f1b0bfa") + (uuid "eef0d131-ae6d-4e8e-a747-8eba69d59f92") ) (segment - (start 134.025 100.725) - (end 134.025 100.7) + (start 128.905238 95.084604) + (end 129.2 95.379366) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "f05afb7d-dd78-48c9-a855-45c2556713ce") + (uuid "f0d9db67-d543-4200-ae2d-a33f2238256a") ) (segment - (start 146.0407 67.8718) - (end 145.8625 68.05) - (width 0.2) + (start 135.65 94.25) + (end 135.65 95.35) + (width 0.3) (layer "B.Cu") (net "GND") - (uuid "f134430a-501b-4429-b4ff-3bc52eeb7b38") + (uuid "f5ee4fcc-5d18-49d2-90f2-958409b0e1a6") ) (segment - (start 131.55 124.1) - (end 131.8 124.35) + (start 134.9 62.8) + (end 135 62.7) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "f1647a48-b0a3-4080-929b-28db36898315") + (uuid "f81b4798-b00a-40b4-9a89-c5b14067c8e9") ) (segment - (start 140.2 69.6) - (end 140 69.4) + (start 129.5625 128.8375) + (end 129.5625 128.425) (width 0.2) (layer "B.Cu") (net "GND") - (uuid "fd872c8a-c4fb-48ad-827b-0c8c33715368") + (uuid "fdccea4a-8ba3-46ec-a059-7a627e27f761") ) (segment - (start 143.6 106.65) - (end 143.5 106.65) + (start 130.2 104.8) + (end 130.2 104.95) (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "fe1d442a-6bc6-497b-92ea-f8243a3db8be") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO4") + (uuid "09d1a41d-dfc8-4d4d-aeea-45d5ad8b37c3") ) (segment - (start 143.6 106.65) - (end 143.8 106.65) + (start 128.6 102.975) + (end 128.8 102.975) (width 0.2) - (layer "B.Cu") - (net "GND") - (uuid "feeb42a8-2d9f-4c6f-ba8f-668b8c7d44a2") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO4") + (uuid "11ea09ab-0d10-4974-820d-693007114cb9") ) (segment - (start 127.975 100.7886) - (end 126.9796 99.7932) + (start 128.8 102.975) + (end 128.8 104.234314) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "4ad431d0-d1a0-4151-90b9-e8beecbb95e5") + (uuid "3785928a-43d6-4947-8f45-3fbfbfc9a938") ) (segment (start 127.975 101.45) - (end 127.975 101.125) + (end 128.6 102.075) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "7cfcd080-2eda-496b-b09b-2bb071be835d") + (uuid "44826335-2c6b-4559-86a7-784ff2375099") ) (segment - (start 123.825 101.45) - (end 124.6517 101.45) + (start 128.6 102.075) + (end 128.6 102.975) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "c5109a10-ee92-42df-be84-6c3f5dc5bbcd") + (uuid "68e35052-e9be-4509-bfa4-0bd7904739c0") ) (segment - (start 129.8 100.7) - (end 128.05 100.7) + (start 129.365686 104.8) + (end 130.2 104.8) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "c9f03d86-ed02-4dec-929f-f30d9861409e") + (uuid "90b4c0f2-0655-4b92-a31a-bef561202c55") ) (segment - (start 127.975 101.125) - (end 127.975 100.7886) + (start 128.8 104.234314) + (end 129.365686 104.8) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "dc3a3c37-a986-45ae-a85a-aa10b98f08c8") + (uuid "af784e7a-4bb4-4821-9b57-684bc3b1efff") ) (segment - (start 126.9796 99.7932) - (end 126.3085 99.7932) + (start 123.825 101.45) + (end 127.975 101.45) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "eb363175-905b-4410-bc69-30614766014d") + (uuid "b1758f4c-c5fd-453f-92d1-7dc6ae52a823") ) (segment - (start 126.3085 99.7932) - (end 124.6517 101.45) + (start 130.2 104.95) + (end 130.55 105.3) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "fce5186e-ec68-4160-a7cd-bd3e0f1649ee") - ) - (via - (at 129.8 100.7) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_MACRO4") - (uuid "58700260-3e8c-4665-bc1d-0e4bd07da511") + (uuid "d3151950-571b-46a8-bc08-367ac4cd8b2d") ) (segment - (start 131 100.7) - (end 129.8 100.7) + (start 130.55 105.3) + (end 130.55 105.5) (width 0.2) - (layer "B.Cu") + (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO4") - (uuid "ac065adf-985d-4060-8791-1ce5cf2b6a73") + (uuid "f86b4b47-1c5e-4c92-85ab-e978dd944b37") ) (segment - (start 125.77 119.275) - (end 125.77 125.5253) - (width 0.4) + (start 145.225 120.3) + (end 145.225 118.865) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "1c726bd9-7b9b-428f-8bd7-09f189611e38") + (net "/MCU_Core/MCU_EN") + (uuid "4a828715-4166-46d6-95c6-89fb8b8123a4") ) (segment - (start 124.79 119.275) - (end 124.75 119.315) + (start 142.65 120.3) + (end 142.45 120.1) (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "1eb47852-e81f-4b44-a394-309ddde0eeb9") + (net "/MCU_Core/MCU_EN") + (uuid "5bfb22ce-80f5-4534-9aaf-7745e8f9d66e") ) (segment - (start 139.45 119.4725) - (end 139.45 121.8689) - (width 0.4) + (start 145.225 120.3) + (end 142.65 120.3) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "243b67fe-d8f4-40d3-8528-ebee1eed4502") + (net "/MCU_Core/MCU_EN") + (uuid "89fa90ac-f31a-4a58-b078-1f4200dc243e") ) (segment - (start 126.91 119.115) - (end 126.75 119.275) + (start 142.45 120.1) + (end 142.45 119.5) (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "2ae86ce6-debd-42c9-8a29-cac75528d615") + (net "/MCU_Core/MCU_EN") + (uuid "8a32954d-5f02-4001-af3a-7061d1e98364") ) (segment - (start 149.2187 109.7038) - (end 139.45 119.4725) - (width 0.4) + (start 145.225 118.865) + (end 145.49 118.6) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "41d4a007-5890-44fd-89de-2e1d87900a95") + (net "/MCU_Core/MCU_EN") + (uuid "b5fbc131-4b27-4aa4-aabb-0a194e60d68c") ) (segment - (start 149.2187 96.6018) - (end 149.2187 109.7038) - (width 0.4) + (start 148.225 112.315) + (end 148.225 112.425) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "8de1f8a7-501a-4d07-b36d-4ad5195b1a4b") + (net "/MCU_Core/MCU_BOOT") + (uuid "07cbc57a-7e1a-4f85-ba41-302ca7646298") ) (segment - (start 128.7 119.115) - (end 126.91 119.115) + (start 144.9 108.3) + (end 145 108.4) (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "ab3440f3-bd0c-4aa8-9ebe-90c8471d1472") + (net "/MCU_Core/MCU_BOOT") + (uuid "271e80c0-521c-40e4-b2e2-6fce2b27f47b") ) (segment - (start 134.55 121.8025) - (end 134.55 123.105) - (width 0.4) + (start 145 109.09) + (end 148.225 112.315) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "dbbc7026-f50f-40f4-9515-302c80beea8d") + (net "/MCU_Core/MCU_BOOT") + (uuid "56b1326f-5838-48c0-9609-2e6b6c8fa3d3") ) (segment - (start 126.75 119.275) - (end 124.79 119.275) - (width 0.3) + (start 139.9 106.4) + (end 139.9 105.5) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "ea53e43f-ef43-4246-8119-87986365c594") + (net "/MCU_Core/MCU_BOOT") + (uuid "aa90eb8d-d3bc-45fb-b00f-7d6a8280991d") ) (segment - (start 139.45 123.105) - (end 139.45 121.8689) - (width 0.4) + (start 148.225 116.575) + (end 148.225 112.425) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "efc68df3-6be2-4b97-808c-c6417b8ceb95") + (net "/MCU_Core/MCU_BOOT") + (uuid "b92912f6-61f3-4462-97dd-f189bc296d04") ) (segment - (start 134.65 121.7025) - (end 134.55 121.8025) - (width 0.4) + (start 145 108.4) + (end 145 109.09) + (width 0.2) (layer "F.Cu") - (net "VBUS") - (uuid "f765d7e8-0ca3-4c06-8dfc-eb433d5e63f7") - ) - (via - (at 125.77 125.5253) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "6cdac9e2-a78f-4c47-b190-095d2a962784") - ) - (via - (at 134.65 121.7025) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "8802b1b1-558f-48e5-b0a6-b6ac0fe13c38") - ) - (via - (at 139.45 121.8689) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "d3f45724-1ca6-4017-bf30-21a9f10e8e62") - ) - (via - (at 141.3213 92.7625) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "d48ed673-9184-4b18-9c3e-2143051739ce") + (net "/MCU_Core/MCU_BOOT") + (uuid "dcf4afe3-dd03-4e33-a481-bc22e002fe35") ) (via - (at 141.703 89.5784) + (at 139.9 106.4) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "da41a0d1-7f7d-4f51-a85c-fa73b4aa3e41") + (net "/MCU_Core/MCU_BOOT") + (uuid "e39ec761-efe7-4a6f-9092-2efd577c74a3") ) (via - (at 149.2187 96.6018) + (at 144.9 108.3) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VBUS") - (uuid "f219472a-5ad0-468b-bc82-3fbfa8e34786") - ) - (segment - (start 133.3663 126.245) - (end 132.6466 125.5253) - (width 0.4) - (layer "B.Cu") - (net "VBUS") - (uuid "3a974c6f-2265-475a-b380-e5398ae48722") - ) - (segment - (start 140.5 89.525) - (end 140.5534 89.5784) - (width 0.4) - (layer "B.Cu") - (net "VBUS") - (uuid "5b10cb70-c7db-471f-ae7e-25227d2a4224") - ) - (segment - (start 141.3213 92.7625) - (end 140.7625 92.7625) - (width 0.4) - (layer "B.Cu") - (net "VBUS") - (uuid "6656a975-a802-446f-a4c1-f49fee2ca508") - ) - (segment - (start 132.6466 125.5253) - (end 125.77 125.5253) - (width 0.4) - (layer "B.Cu") - (net "VBUS") - (uuid "a2ec7fb9-edab-4759-a01d-d02473f7f309") + (net "/MCU_Core/MCU_BOOT") + (uuid "ed74f656-3330-445f-8c2f-445ad70a5e01") ) (segment - (start 140.7625 92.7625) - (end 140.025 93.5) - (width 0.4) + (start 144.4 108.8) + (end 142.3 108.8) + (width 0.2) (layer "B.Cu") - (net "VBUS") - (uuid "ba5c5289-0fcc-473d-bfdc-d942baf781f8") + (net "/MCU_Core/MCU_BOOT") + (uuid "454efeca-52b5-4592-8c7c-ef18500b49b2") ) (segment - (start 140.5534 89.5784) - (end 141.703 89.5784) - (width 0.4) + (start 142.3 108.8) + (end 139.9 106.4) + (width 0.2) (layer "B.Cu") - (net "VBUS") - (uuid "cc933d88-1313-4e72-9fe3-b1be3bc266f1") + (net "/MCU_Core/MCU_BOOT") + (uuid "888eceaa-0f87-45c2-aee0-3ea482adf02f") ) (segment - (start 135.845 126.245) - (end 133.3663 126.245) - (width 0.4) + (start 144.9 108.3) + (end 144.4 108.8) + (width 0.2) (layer "B.Cu") - (net "VBUS") - (uuid "d372ec1e-e789-4f37-a333-84e15ec018ea") - ) - (segment - (start 141.703 92.3808) - (end 141.3213 92.7625) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "0f2a71d7-950c-4bc9-a5cb-87c7a602f992") - ) - (segment - (start 135.1502 122.2027) - (end 139.1162 122.2027) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "16ef771a-5a36-41b6-9fce-1a60fe5141d0") - ) - (segment - (start 142.558 96.6018) - (end 149.2187 96.6018) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "1cfc2a81-73ca-456d-ae19-96314cdaa5d0") - ) - (segment - (start 141.3213 95.3651) - (end 142.558 96.6018) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "23a9e68f-0e0e-445f-8f38-1815491ef537") - ) - (segment - (start 125.77 125.5253) - (end 129.847 121.4483) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "3d198150-1dbd-4dff-80c5-11cbd6df09dc") - ) - (segment - (start 134.65 121.7025) - (end 135.1502 122.2027) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "5e58b383-3371-432d-8f1e-43281c1f9459") - ) - (segment - (start 129.847 121.4483) - (end 134.3958 121.4483) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "601efd9f-d21d-4640-bd60-585921a5e0fc") - ) - (segment - (start 141.3213 92.7625) - (end 141.3213 95.3651) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "754caca6-bddc-4122-960d-31eeed358bda") - ) - (segment - (start 141.703 89.5784) - (end 141.703 92.3808) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "aca25b51-a053-4d57-b9d8-2f377348829c") - ) - (segment - (start 139.1162 122.2027) - (end 139.45 121.8689) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "d99b9d35-d374-4f49-b00f-3edb11f1d491") - ) - (segment - (start 134.3958 121.4483) - (end 134.65 121.7025) - (width 0.4) - (layer "In1.Cu") - (net "VBUS") - (uuid "fb877b3e-782a-4512-824c-fdc29f18df31") + (net "/MCU_Core/MCU_BOOT") + (uuid "e4400d6d-708f-4dc4-a52f-ccfebda85807") ) (segment - (start 127.85 128.65) - (end 129.0983 127.4017) + (start 130.6 101.668529) + (end 130.99 102.058529) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "01463fb3-8864-4754-8e93-99d029f3d28d") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "023be37a-745f-47d1-8982-d7df26af42f1") ) (segment - (start 123.9 107.4061) - (end 123.9 113.6584) + (start 130.549998 93.079364) + (end 130.549998 95.829896) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "027dc7c4-c63d-4579-b20c-48921964a12c") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "142070d6-4a79-4fc4-9718-dc13eacb55c3") ) (segment - (start 130.9815 123.3725) - (end 128.594 120.985) + (start 130.4 96.067155) + (end 130.4 97.026471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "0313ee6e-5a09-4199-9850-2d24e3ac00ac") - ) - (segment - (start 124.26 117.315) - (end 124.65 117.315) - (width 0.3) - (layer "F.Cu") - (net "3V3") - (uuid "17ec856f-d44a-4224-a156-960fb13125ea") - ) - (segment - (start 132.425 109.8) - (end 131.475 110.75) - (width 0.55) - (layer "F.Cu") - (net "3V3") - (uuid "226500fd-0cda-4dca-90d6-28b9c2dced14") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "16034d94-6d82-486c-9a26-7443ba3d70c2") ) (segment - (start 134.86 114.515) - (end 132.645 112.3) + (start 130.4 99.551471) + (end 130.6 99.751471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "2a3b55e6-690c-4f4f-8e63-5368965411eb") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "3013763b-9088-44a0-807d-5837dfdd79b8") ) (segment - (start 131.4158 125.4159) - (end 130.9815 124.9816) + (start 130.6 101.448529) + (end 130.6 101.668529) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "3283e21f-a910-434a-9014-9d03b4754d1a") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "36898699-72a1-47bd-aaa9-695b7c746efc") ) (segment - (start 131.4158 126.713) - (end 131.4158 125.4159) + (start 130.6 99.751471) + (end 130.6 100.751471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "443eaf25-75ae-4fc9-b9cd-b62e9d171fb3") - ) - (segment - (start 131.475 110.75) - (end 131.475 111.825) - (width 0.55) - (layer "F.Cu") - (net "3V3") - (uuid "4f054551-84c2-42e2-a01e-009b442e97c9") - ) - (segment - (start 132.95 108.035) - (end 131.975 107.06) - (width 0.55) - (layer "F.Cu") - (net "3V3") - (uuid "58afdcee-66b6-43c2-88ab-0e786990323a") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "433bfb24-968b-48bb-997f-d42cb49b78db") ) (segment - (start 127.0477 123.9723) - (end 127.27 123.75) + (start 130.593628 95.873527) + (end 130.4 96.067155) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "597a586a-e7e7-4765-8db5-2e93bf5d820d") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "454ae5d1-7bbc-4c42-8e9d-506bbfabf729") ) (segment - (start 127.85 128.65) - (end 127.0477 127.8477) + (start 132.25 105.5) + (end 132.25 104.48) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "5d2247f4-cbb7-4c95-90d8-1da09243dc4d") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "7504189a-f369-4386-9e2b-dedec5e22d8f") ) (segment - (start 128.38125 121.17) - (end 127.3 121.550001) + (start 130.99 102.058529) + (end 130.99 103.22) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "64eb8012-b0d1-4b1b-9574-d5d8750882dd") - ) - (segment - (start 132.95 109.8) - (end 132.425 109.8) - (width 0.55) - (layer "F.Cu") - (net "3V3") - (uuid "6de9dbb8-aced-46da-85f2-3fea9fe9b81f") - ) - (segment - (start 124.26 117.315) - (end 123.86 116.915) - (width 0.3) - (layer "F.Cu") - (net "3V3") - (uuid "7955424c-5a35-47a3-862c-5d5a7f0bcd15") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "838d53ac-d637-4e7b-a847-f78f7f921cb1") ) (segment - (start 132.645 112.3) - (end 131.95 112.3) + (start 130.549998 95.829896) + (end 130.593628 95.873527) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "8051b673-fe27-48e4-831b-3fde6550eab5") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "8b0ab986-babc-48d2-a5b0-ac6d3176a5ef") ) (segment - (start 129.0983 127.4017) - (end 130.7271 127.4017) + (start 130.25 97.673529) + (end 130.4 97.823529) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "81b14fba-2102-4774-88ad-c6c248b982a0") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "8c1c47a1-8874-4e23-bbe5-cc9934365142") ) (segment - (start 123.9 106.125) - (end 123.9 107.4061) + (start 130.99 103.22) + (end 131.6 103.83) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "987dbddc-1141-4e01-aa72-6dec579a7cc5") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "904b67b6-ebf2-484c-8834-59048384987d") ) (segment - (start 130.9815 124.9816) - (end 130.9815 123.3725) + (start 130.5 101.348529) + (end 130.6 101.448529) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "a6aa2ff3-a5d4-4863-a44a-73fb6ccfac09") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "9a237b66-b91f-499a-9b50-ad4776873ec1") ) (segment - (start 130.7271 127.4017) - (end 131.4158 126.713) + (start 130.5 100.851471) + (end 130.5 101.348529) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "a9e9c6eb-c7bd-4686-9ab7-24651a9a4e99") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "aaa813fa-c1cc-4d15-95f4-ef03f900020e") ) (segment - (start 127.0477 127.8477) - (end 127.0477 123.9723) + (start 130.4 97.823529) + (end 130.4 99.551471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "b201db1b-50df-487c-b808-0139cd4bfe11") - ) - (segment - (start 134.45 109.8) - (end 132.95 109.8) - (width 0.55) - (layer "F.Cu") - (net "3V3") - (uuid "b650dc78-93f9-474c-8167-58737faeed13") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "af32ab50-ecb1-4077-ba63-09ef8af77ca2") ) (segment - (start 128.38125 120.800001) - (end 128.38125 121.17) + (start 130.4 97.026471) + (end 130.25 97.176471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "c3682bd8-6212-40a6-bdb8-d3ac861089ae") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "b8569ff0-234e-49ab-a38c-c5ba4fbbb9e9") ) (segment - (start 124.5492 107.4061) - (end 123.9 107.4061) + (start 130.6 100.751471) + (end 130.5 100.851471) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "cf2a7d4a-d27b-4bf6-b233-0f168df9a733") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "d2e95b16-64ab-429a-a7e9-272463c6ad4f") ) (segment - (start 128.594 120.985) - (end 128.381 120.985) + (start 130.070634 92.6) + (end 130.549998 93.079364) (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "d0b79bde-3619-4789-942a-31718509eef0") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "d2f4e52a-47b2-4a08-9dff-b97edecf7076") ) (segment - (start 132.95 109.8) - (end 132.95 108.035) - (width 0.55) + (start 132.25 104.48) + (end 131.6 103.83) + (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "eefd1290-1f50-4de4-84dd-1c6108755cc9") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "d8910776-d4d6-498e-b2de-24d30fa0dc2a") ) (segment - (start 131.475 111.825) - (end 131.95 112.3) - (width 0.55) + (start 130.25 97.176471) + (end 130.25 97.673529) + (width 0.2) (layer "F.Cu") - (net "3V3") - (uuid "f9f2503a-25e1-4c24-9278-d81ecb7650c9") - ) - (via - (at 131.95 112.3) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "196ae5c3-bdf8-465b-b0a7-e3598ef31458") - ) - (via - (at 127.3 121.550001) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "482cf433-06d1-49af-8b76-1a3ffd87d383") - ) - (via - (at 123.9 113.6584) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "572d7a8b-c517-4661-bacf-c462e2596ee2") - ) - (via - (at 146.1203 98.555) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "768be7ad-a960-43b2-8378-1137b8f5c1a0") - ) - (via - (at 124.5492 107.4061) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "770fa52e-247e-4c6a-9c40-cc842e66599c") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "e3d3c396-c9aa-4e7d-afaa-742f65bd457f") ) (via - (at 123.86 116.915) + (at 130.070634 92.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "3V3") - (uuid "f11d95a4-4cdf-4b91-85fe-e86ab50f61cd") - ) - (segment - (start 144.2 66.8875) - (end 144.2 67.2759) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "0acaaa5a-0b93-4f96-8933-735300539370") - ) - (segment - (start 125.875 100.76) - (end 125.1772 101.4578) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "0ef2d6cc-0b2d-43b6-8aa5-719538f4b570") - ) - (segment - (start 141.6207 90.5116) - (end 142.1081 90.0242) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "11d0cf8c-77fb-4103-81d1-8b8a94cf1305") - ) - (segment - (start 145.2 68.7125) - (end 145.2 69.97) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "21832654-a9b9-4362-b234-e4fda6c71073") - ) - (segment - (start 139.0375 91.375) - (end 139.9009 90.5116) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "25f87063-1ebf-472d-8190-933c68b117f8") - ) - (segment - (start 123.575 107.8) - (end 124.1553 107.8) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "2ca7d258-810b-4aee-b943-bd5813bcc002") - ) - (segment - (start 147.7299 93.1502) - (end 144.6039 90.0242) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "2e9b972f-7277-408b-a4e6-8b18e7251b98") - ) - (segment - (start 146.9842 84.6368) - (end 146.264 83.9166) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "310e9ce0-4f49-483c-a26a-d2d3c5c0bcf1") - ) - (segment - (start 146.9842 87.6439) - (end 146.9842 84.6368) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "34c44ba8-8550-41a5-a7a4-977ae1a783a7") - ) - (segment - (start 125.8478 103.01) - (end 123.96 104.8978) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "466a8900-c67d-437f-a002-7db30c91845d") - ) - (segment - (start 144.2 66.7822) - (end 144.2 66.8875) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "4aa25a08-b445-445b-bb89-41df3ac702c5") - ) - (segment - (start 131.95 112.3) - (end 133.3069 113.6569) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "4dac41b0-3d16-4b7d-9ac5-6499a4fdb662") - ) - (segment - (start 142.28 68.55) - (end 142.25 68.52) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "56440512-1a10-48e0-b6f7-e6cd94cadffa") - ) - (segment - (start 123.96 105.2) - (end 123.96 107.415) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "57d65168-b73f-4b9a-880c-2db64b350131") - ) - (segment - (start 123.96 107.415) - (end 123.575 107.8) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "5f30f6e8-9a9c-47a6-b28b-4a521a270865") - ) - (segment - (start 144.2 67.2759) - (end 145.2 68.2759) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "6ccfc1e8-0415-4e3e-9ee9-5a0a6856e911") - ) - (segment - (start 142.205 68.475) - (end 142.205 67.1727) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "6d77ce75-1c26-456f-a4cb-68355e0c8e74") - ) - (segment - (start 139.9009 90.5116) - (end 141.6207 90.5116) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "7144c9c3-f200-45a0-b89e-e3a8c9fa09cf") - ) - (segment - (start 143.9451 66.5273) - (end 144.2 66.7822) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "75778aee-5d8f-4662-883b-0639f18f5dba") - ) - (segment - (start 145.2 69.97) - (end 145.23 70) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "77b34a88-422f-4605-bce5-4f79b2f20849") - ) - (segment - (start 142.1081 90.0242) - (end 144.6039 90.0242) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "8d6c1823-c018-445a-8d52-cc49db4f1af5") - ) - (segment - (start 146.264 83.9166) - (end 146.264 71.034) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "8d90bd74-b085-402d-9d34-dbb51e23c581") - ) - (segment - (start 140.75 68.475) - (end 142.205 68.475) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "92dd22b5-5b5b-4481-8f4d-9d25128dd167") - ) - (segment - (start 147.7299 97.405) - (end 147.7299 93.1502) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "94283a81-a2e2-4471-9dac-c485942c3130") - ) - (segment - (start 142.8504 66.5273) - (end 143.9451 66.5273) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "a13e92f5-cc7c-456e-ad40-a1acf6e921a7") - ) - (segment - (start 145.5131 113.6569) - (end 145.665 113.505) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "a4b22f9b-53d4-41e8-afdb-b37d97ab8ad8") - ) - (segment - (start 125.1772 101.4578) - (end 125.1772 102.3122) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "a6be0e86-61af-4c10-8301-6a6a6efa9fb4") - ) - (segment - (start 143.5375 68.55) - (end 142.28 68.55) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "a7a2bde4-445e-4bfb-b57b-361778dceb43") - ) - (segment - (start 146.264 71.034) - (end 145.23 70) - (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "a885e21c-fcc0-486f-9a66-afb58ff6dfbd") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "7601877f-c95c-4d99-8588-1ab1475f4870") ) (segment - (start 125.1772 102.3122) - (end 125.875 103.01) + (start 129.75 92.279366) + (end 130.070634 92.6) (width 0.2) (layer "B.Cu") - (net "3V3") - (uuid "ae4ee46e-0355-45b5-b21a-ed874ef5716a") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "4387ea50-ecf8-47b5-ae00-c603468edf0a") ) (segment - (start 123.96 104.8978) - (end 123.96 105.2) + (start 129.75 91.76) + (end 129.75 92.279366) (width 0.2) (layer "B.Cu") - (net "3V3") - (uuid "b3145197-378c-4f0f-96bb-81f8f50e0199") + (net "/Hall_Trigger/TRIG_ADC") + (uuid "f9bc0558-f82d-4bf5-b67a-f70e4c48e1ad") ) (segment - (start 146.1203 98.555) - (end 146.5799 98.555) + (start 133.75 96.598529) + (end 133.75 95.075) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "ba905f0b-60b6-4256-b8e1-465168a15878") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "09f637ea-fbdb-4200-a2c0-4f78ab7f94de") ) (segment - (start 124.1553 107.8) - (end 124.5492 107.4061) + (start 133.75 95.075) + (end 132.925 94.25) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "bb5da82a-4cd6-4349-b05b-e75a97c02ba6") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "1f6174c3-c503-4985-a078-9c668ded2450") ) (segment - (start 133.3069 113.6569) - (end 145.5131 113.6569) + (start 135.65 105.5) + (end 135.65 102.040686) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "c79a2582-f2bf-42c5-82be-eaf805ab915f") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "271ad422-487b-42bb-9f74-be780e9c3c6c") ) (segment - (start 146.5799 98.555) - (end 147.7299 97.405) + (start 134.8 97.648529) + (end 133.75 96.598529) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "cd9d03e1-c608-406b-9212-43c0e801835c") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "3f0717eb-02d8-4836-80e3-8501e7dc0a05") ) (segment - (start 144.6039 90.0242) - (end 146.9842 87.6439) + (start 137.075 94.25) + (end 132.925 94.25) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "cda49612-465a-4931-b2db-581714cbb02c") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "5546e62f-5b1c-4071-a487-00a5a88ac302") ) (segment - (start 144.9467 98.6467) - (end 146.0286 98.6467) + (start 135.65 102.040686) + (end 134.8 101.190686) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "d216f0da-f98b-45f4-bf43-2160f752faf8") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "7ce333f7-6e51-4fc1-a4bd-ba48912425d1") ) (segment - (start 124.9 94.6) - (end 124.9 99.785) + (start 134.8 101.190686) + (end 134.8 97.648529) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "d3a9d5d8-f3be-44f8-a1bb-352ec721a0a6") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO2") + (uuid "a5690968-d1f3-4d7a-b1ca-43cf6bf6af5b") ) (segment - (start 124.9 99.785) - (end 125.875 100.76) + (start 136.25 123.105) + (end 136.25 123.86241) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "d4e12ac3-66ad-48a2-b603-0f09771eeaa9") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "08d95296-e8f2-4327-95e7-fb69644a3ede") ) (segment - (start 142.205 67.1727) - (end 142.8504 66.5273) + (start 136.25 123.86241) + (end 136.68759 124.3) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "d8cefe0d-cad5-4769-bf24-5399edc7093e") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "0b744dae-7453-41ea-b376-65da33f4d021") ) (segment - (start 125.875 103.01) - (end 125.8478 103.01) + (start 127.75 115.25) + (end 128.02 114.97) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "e10747a3-c419-4fb3-9f26-d0d786e74fc2") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "18da7a7e-6a29-44cf-b080-9595516a187f") ) (segment - (start 142.205 68.475) - (end 142.25 68.52) + (start 136.25 123.105) + (end 136.25 122.281905) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "e47cf250-2242-4e2c-9689-fab5a7d89822") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "382fc874-0eb4-4c56-a0ae-29f20f546de9") ) (segment - (start 144.565 98.265) - (end 144.9467 98.6467) + (start 135.648095 121.68) + (end 130.654314 121.68) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "e5ff1bab-2aad-450b-8b6a-8fe028bc5844") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "578c39ae-2464-4063-8681-14d2800c4393") ) (segment - (start 145.2 68.2759) - (end 145.2 68.7125) + (start 124.6 115.25) + (end 127.75 115.25) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "f55e79af-fb7c-4dcc-9e38-115440cdb8f4") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "590c11bb-e0ed-4959-a447-b0bc2f994234") ) (segment - (start 146.0286 98.6467) - (end 146.1203 98.555) + (start 130.654314 121.68) + (end 130.634315 121.7) (width 0.2) - (layer "B.Cu") - (net "3V3") - (uuid "fa7b1406-fc62-4f4b-ba76-597d2236b212") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "912c8d8a-152a-41ed-802a-1d1cbf751f28") ) (segment - (start 124.6652 118.9152) - (end 124.6652 117.7202) + (start 130.634315 121.7) + (end 126.4 121.7) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "4345044d-68fd-4fe4-b48a-3b8981ecab0b") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "a041b43c-bcd0-4236-b334-3e4d0d58b7e1") ) (segment - (start 131.95 112.3) - (end 125.2584 112.3) + (start 124.6 119.9) + (end 124.6 115.25) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "568ebe90-6def-4975-a07b-e9d35ad031b7") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "b6dfec82-a308-4c2b-8520-0b4c1530141d") ) (segment - (start 124.5492 107.4061) - (end 127.6533 107.4061) + (start 137.25 123.86241) + (end 137.25 123.105) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "5b12994f-6e9a-4534-9cb3-5fb45e7447f7") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "bdb59a2f-7add-4445-9c8d-b0b4a2c78bd8") ) (segment - (start 127.6533 107.4061) - (end 132.4429 102.6165) + (start 136.68759 124.3) + (end 136.81241 124.3) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "6989afd6-ba6f-455c-bde5-e06986057d13") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "ca7c5122-bbac-448a-b53e-5cb857c11629") ) (segment - (start 123.86 116.915) - (end 123.86 113.6984) + (start 136.25 122.281905) + (end 135.648095 121.68) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "808021f7-2d39-4c73-892b-d685aa47e7fc") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "f2c31c03-9404-4348-9add-8a002c4dd527") ) (segment - (start 132.4429 102.6165) - (end 142.0588 102.6165) + (start 136.81241 124.3) + (end 137.25 123.86241) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "84ce0b44-bd55-4bea-b0df-a8595661b27b") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "f3a3a3e2-8402-4cd6-a5cd-565224c10699") ) (segment - (start 142.0588 102.6165) - (end 146.1203 98.555) + (start 126.4 121.7) + (end 124.6 119.9) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "cf9463e6-705e-49fb-be14-fdeec38786a4") + (layer "F.Cu") + (net "/MCU_Core/USB_DM") + (uuid "f4c2e67e-3ca0-4c6d-b10c-3655927568ad") ) (segment - (start 124.6652 117.7202) - (end 123.86 116.915) + (start 128.1 112.5) + (end 128.1 113.98) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "e4b84d28-694d-4a6c-b0ce-2160e330ae71") + (layer "F.Cu") + (net "/MCU_Core/USB_DM_MCU") + (uuid "7d0d8dbd-14f0-4b40-9541-9db94d5e8528") ) (segment - (start 125.2584 112.3) - (end 123.9 113.6584) + (start 129.5 112.5) + (end 128.1 112.5) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "f1f525fb-89e4-4900-bbec-cbb53ef3dfb8") + (layer "F.Cu") + (net "/MCU_Core/USB_DM_MCU") + (uuid "bb6dfef1-82ef-4530-ba66-02921f2f1262") ) (segment - (start 127.3 121.55) - (end 124.6652 118.9152) + (start 121.8 74.725) + (end 121.3 74.225) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "f5856f6e-9ba6-4009-b88a-b488d11543ad") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "17fa9539-7c6d-4ac5-b67b-27063783c8e2") ) (segment - (start 123.86 113.6984) - (end 123.9 113.6584) + (start 124.7 84.422057) + (end 124.7 76.725) (width 0.2) - (layer "In1.Cu") - (net "3V3") - (uuid "fdff1730-6701-4456-8c57-b637a5f10986") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "2c9294db-7b26-420a-a2ff-decc58f5cea9") ) (segment - (start 137.075 94.25) - (end 132.925 94.25) + (start 121.87393 107.063387) + (end 121.810543 107) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "06299e43-44cc-461e-b065-c6366c5ab5ea") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "300954d6-0a12-4485-8bf3-46ca541b8c87") ) (segment - (start 132.0983 94.8178) - (end 132.0983 94.25) + (start 120.8 97.734315) + (end 120.8 88.322057) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "24c7886e-5d3d-4bac-8e74-0d1c26c7b71f") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "37ec2cb7-22b8-4f9a-a00a-3ffac13f05eb") ) (segment - (start 131.797 95.1191) - (end 132.0983 94.8178) + (start 121.3 74.225) + (end 121.3 73.3) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "3c3292fe-14d9-49cb-a00d-dea5af0750eb") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "57df3fd5-dd6f-4351-aa15-3baf0dde3810") ) (segment - (start 132.925 94.25) - (end 132.0983 94.25) + (start 120.8 88.322057) + (end 124.7 84.422057) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "c333cb5f-8487-45ac-8e7f-850ef6c3c5c7") - ) - (via - (at 131.797 95.1191) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "04753517-3bbe-48a8-bf82-2348ebd529b7") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "625b34c6-8509-4925-be94-d0440be58c3e") ) (segment - (start 132.2161 94.7) - (end 131.797 95.1191) + (start 121.3 107) + (end 120.9 106.6) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "59deddb1-7c62-4537-a896-45d25f1aab11") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "6e28161e-50d3-4ca4-a593-1c50886d5d54") ) (segment - (start 132.525 94.7) - (end 132.2161 94.7) + (start 122.7 74.725) + (end 121.8 74.725) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO2") - (uuid "9fe1468b-7767-46c3-b06b-8f41a63b9e65") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "80c6aea3-afa0-4af0-9711-afc06daff5ad") ) (segment - (start 121.4616 73.8045) - (end 121.4616 73.1279) + (start 124.7 76.725) + (end 122.7 74.725) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "0da0022d-80b0-442a-ad09-2fe75d9cb83e") + (uuid "88e201a9-d255-4871-bec8-1289817de3e6") ) (segment - (start 122.1752 72.7998) - (end 122.7 72.275) + (start 129.65 116.6) + (end 129.5 116.75) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "3277c4f8-bf33-41ce-9e59-4e193ff8f691") + (uuid "97675d0a-2937-4d91-ad5c-44fea5529f57") ) (segment - (start 122.3821 74.725) - (end 121.4616 73.8045) + (start 120.9 106.6) + (end 120.9 97.834315) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "458cd178-5389-4605-b624-4c2f164abf41") + (uuid "ad95e9fb-4d67-476c-b0fa-219e4366e200") ) (segment - (start 124.7546 76.7796) - (end 122.7 74.725) + (start 121.3 73.3) + (end 122.325 72.275) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "6da38256-e9c8-4b7e-8a63-c1f6e8d71345") + (uuid "b7ad4f77-d265-43b8-81a8-0fd60ae7f179") ) (segment - (start 122.7 74.725) - (end 122.3821 74.725) + (start 130.3 116.6) + (end 129.65 116.6) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "9ee1e9a0-c499-43e8-8470-1d112392367f") + (uuid "bbb42b80-6c3d-4cc0-b134-6594d18e9812") ) (segment - (start 121.4616 73.1279) - (end 121.7897 72.7998) + (start 120.9 97.834315) + (end 120.8 97.734315) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "abbf56cc-a8fc-442f-9240-1b3c3495e32a") + (uuid "be5f5d34-5b78-4b2e-863b-1090020ae7c8") ) (segment - (start 124.7546 83.4341) - (end 124.7546 76.7796) + (start 121.810543 107) + (end 121.3 107) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "dd12b2ee-8ea6-4234-b52c-af677508b980") + (uuid "d8f0b947-c5cc-4b0c-995c-577859522094") ) (segment - (start 121.7897 72.7998) - (end 122.1752 72.7998) + (start 122.325 72.275) + (end 122.7 72.275) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "fc02fec3-c02b-4bfa-a054-be266532cc30") + (uuid "db14d9ba-ecb3-40a0-b3f5-0572354ba0f9") ) (via - (at 124.7546 83.4341) + (at 121.87393 107.063387) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "64fdfac5-e1ad-4466-9b14-2676a75ac6cc") + (uuid "47801111-f962-493f-b593-1e06b286937b") ) (via - (at 132.6208 86.6882) + (at 130.3 116.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "9946707b-e55a-45df-abab-23a0fe6e5971") + (uuid "d5c0ea11-c2fb-4ca4-a1e5-5d222dedfd66") ) (segment - (start 133.5842 87.6516) - (end 133.5842 89.784) + (start 122.3 107.5) + (end 124.834314 107.5) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "19367a7d-67e7-4d73-991d-5b7203621fa4") + (uuid "0cb41d01-dbe4-4bef-9d4a-1fee22394a3c") ) (segment - (start 132.5622 93.4628) - (end 132.525 93.5) + (start 131.1 113.951471) + (end 131.1 115.8) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "2c2b7f71-7ffd-4c70-9c62-826fe24afac7") + (uuid "6c954a46-02ee-4619-a0a1-d10c7ecfb768") ) (segment - (start 132.6208 86.6882) - (end 133.5842 87.6516) + (start 124.834314 107.5) + (end 127.448529 110.114215) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "6930c70a-9566-4790-bbf8-4c984811a207") + (uuid "7f46e997-a423-4874-93e0-afb663ed4b34") ) (segment - (start 133.5842 89.784) - (end 132.5622 90.806) + (start 121.87393 107.063387) + (end 121.87393 107.07393) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "a8d9506e-e989-424e-b684-478c3f76b0f1") + (uuid "864928c0-bd3a-4108-8b33-be1771c545c5") ) (segment - (start 132.5622 90.806) - (end 132.5622 93.4628) + (start 121.87393 107.07393) + (end 122.3 107.5) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "ea3a04df-a966-40a6-90e1-b06c04d449b5") + (uuid "a2b76244-c488-4eaf-b864-20f27f7b7c4b") ) (segment - (start 132.6208 86.6882) - (end 128.0087 86.6882) + (start 127.448529 110.3) + (end 131.1 113.951471) (width 0.2) - (layer "In1.Cu") + (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "036426b9-fe51-42ce-8ea2-971a07ac7af0") + (uuid "af1c5cea-cc93-46db-8b15-6a5f7aa0f541") ) (segment - (start 128.0087 86.6882) - (end 124.7546 83.4341) + (start 131.1 115.8) + (end 130.3 116.6) (width 0.2) - (layer "In1.Cu") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_THR_UP") + (uuid "d1fdc9f5-e0bb-44d3-a5b6-38fff45472b1") + ) + (segment + (start 127.448529 110.114215) + (end 127.448529 110.3) + (width 0.2) + (layer "B.Cu") (net "/Buttons_Direct/BTN_THR_UP") - (uuid "f96bc713-7c1b-45d3-8b19-809e1e33d61c") + (uuid "df773f91-9f3d-424a-b9ee-1d2b8fcb7450") ) (segment - (start 140.475 101.45) - (end 139.2093 100.1843) + (start 142.6 102.4) + (end 142.6 102.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO6") - (uuid "597b67dc-a82b-4a0a-9cf5-a381f5372b48") + (uuid "1a95c6ed-a2f6-40a4-9e96-dc8eed25e07e") ) (segment - (start 142.025 101.45) - (end 140.475 101.45) + (start 140.9 107) + (end 141.3 106.6) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO6") - (uuid "6291e849-7923-4233-9248-f4ee6f8e8b54") + (uuid "1c013192-970a-45bc-853e-6c1c758b7751") ) (segment - (start 146.175 101.45) + (start 142.6 102.025) (end 142.025 101.45) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO6") - (uuid "a56ff511-28aa-48ad-9a8b-3d5ba19d840b") + (uuid "20712af1-12d5-4f07-9715-8e90a87d1d69") + ) + (segment + (start 138.851471 107) + (end 140.9 107) + (width 0.2) + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "3a0587f7-b59a-4e43-a140-770be70d67d1") + ) + (segment + (start 138.2 106.348529) + (end 138.851471 107) + (width 0.2) + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "65e98ee7-75c8-42ef-b7f7-e9852997911a") + ) + (segment + (start 138.2 105.5) + (end 138.2 106.348529) + (width 0.2) + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "6678742d-4a43-4522-b67f-e4b13b3dd3f8") + ) + (segment + (start 142.025 101.45) + (end 146.175 101.45) + (width 0.2) + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "b5f29316-df2f-4ceb-acae-401cffd26340") + ) + (via + (at 141.3 106.6) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "c40aa2ad-796b-4462-9962-8dfdfeec14a6") ) (via - (at 139.2093 100.1843) + (at 142.6 102.4) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "/Buttons_Direct/BTN_MACRO6") - (uuid "d1f04909-7d4f-497e-b8de-fdf8e431c163") + (uuid "f24ed8d7-9e3e-4866-8331-d2af70831193") + ) + (segment + (start 142.6 105.3) + (end 142.6 102.4) + (width 0.2) + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO6") + (uuid "73708f99-b600-47b6-a729-792c7fffa745") ) (segment - (start 138.525 99.5) - (end 139.2093 100.1843) + (start 141.3 106.6) + (end 142.6 105.3) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_MACRO6") - (uuid "532dba82-743a-42c0-9a60-b72c967a4b69") + (uuid "b6ee3c22-a246-4e51-8239-3106b8c3dc04") ) (segment - (start 141.1983 94.25) - (end 141.1983 97.0346) + (start 135.3 101.125) + (end 135.3 98.751471) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "1bed0e3a-7b70-4e8a-8610-8889c8013a43") + (uuid "04668737-4b16-4bd0-acca-5dd89d00f013") ) (segment - (start 142.2125 94.25) - (end 142.8517 94.25) + (start 138.15 94.25) + (end 142.025 94.25) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "3ce91910-61e0-45e8-893d-d198d97ebec0") + (uuid "178b92d4-d98e-4100-8978-d61392f65b0c") ) (segment - (start 141.1983 97.0346) - (end 139.7898 98.4431) + (start 136.5 105.5) + (end 136.25 105.25) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "5770d023-4366-4cb5-80c4-5fce0a9550e2") + (uuid "2e69c0cf-e4b9-409f-a514-418eb988f26d") ) (segment - (start 142.1124 94.25) - (end 142.1998 94.25) + (start 136.25 105.25) + (end 136.25 102.075) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "7ef8cc83-e7a2-4262-9c5d-7964be470003") + (uuid "6a3aa7d3-682b-40af-b7c5-5320b775b778") ) (segment - (start 142.1124 94.25) - (end 142.025 94.25) + (start 142.025 94.25) + (end 146.175 94.25) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "80a6b2dd-cae8-47ed-ac15-f148aa5b7ee6") + (uuid "88d2acd4-1c43-4da7-a494-408103aa686d") ) (segment - (start 144.9813 93.883) - (end 143.2187 93.883) + (start 136.25 102.075) + (end 135.3 101.125) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "94cad6ac-2230-4e3e-85c4-2899892f32bc") + (uuid "88e952a1-6490-467b-9024-410f371a2314") ) (segment - (start 145.3483 94.25) - (end 144.9813 93.883) + (start 138.1 97.025) + (end 138.1 94.3) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "96fbdc90-f164-4a57-9af0-623493ffbfd0") + (uuid "8e521a76-d351-4cd2-a90f-5962db6ab9a4") ) (segment - (start 142.2125 94.25) - (end 142.1998 94.25) + (start 137.026471 97.025) + (end 138.1 97.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "a1932b8e-585b-48f6-a124-db55a8c1c501") + (uuid "dba119ba-0889-4586-bf59-032e644c8d76") ) (segment - (start 143.2187 93.883) - (end 142.8517 94.25) + (start 138.1 94.3) + (end 138.15 94.25) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "bff9ce3d-5980-489b-9a71-fe526dbc8924") + (uuid "f8a82c8e-3680-4c49-a830-002b5d2d8b2c") ) (segment - (start 146.175 94.25) - (end 145.3483 94.25) + (start 135.3 98.751471) + (end 137.026471 97.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO3") - (uuid "d4f5c8c3-2c8a-4c99-9a69-d6265fdc6d5b") + (uuid "fb1d675b-55e3-4a7e-a4db-d9b6f47e42f3") ) (segment - (start 142.025 94.25) - (end 141.1983 94.25) + (start 122.6 103.4) + (end 121.7 103.4) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "f510cee9-dfef-48ba-b991-2c2e1b916782") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "175a8a04-de70-4871-8599-07f71784db00") ) - (via - (at 139.7898 98.4431) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "c1d4eb4a-153e-48d6-ace9-8491ce02e647") + (segment + (start 123.825 94.25) + (end 127.975 94.25) + (width 0.2) + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "305514ad-914a-4e21-b839-fd394330c033") ) (segment - (start 139.7898 98.4431) - (end 139.7055 98.4431) + (start 123.025 102.975) + (end 122.6 103.4) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "17ef6d90-3998-4e7b-8f49-6a0dfa19d4e2") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "52e734b5-4910-47b4-98fa-ea3a38a1fa36") ) (segment - (start 139.7055 98.4431) - (end 138.525 97.2626) + (start 121.7 103.4) + (end 121.7 98.325) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "55af3d5f-84df-4df0-928b-f0bb96fabc92") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "54be6c1e-5054-4a0a-b9a5-bb11c1ec459b") ) (segment - (start 138.525 97.2626) - (end 138.525 97.1) + (start 123 95.075) + (end 123.825 94.25) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO3") - (uuid "c29d8bd8-5deb-4380-ab07-d16b91736d36") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "62322bbd-e066-4f7f-8f0f-d3681ef6ac59") ) (segment - (start 127.975 94.25) - (end 127.1483 94.25) + (start 126.774998 104.025) + (end 125.7 104.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "32ff47b5-9dc1-434d-84cf-cc0986bc28fd") + (uuid "6dbd1a97-de13-4c07-8e95-6e68cb864b38") ) (segment - (start 127.12 94.2783) - (end 127.1483 94.25) + (start 123 97.025) + (end 123 95.075) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "4f27a275-cda9-44e5-aa28-b44b83633351") + (uuid "754e53d5-456e-4690-a5e3-24ba9c7693e0") ) (segment - (start 123.825 94.25) - (end 124.6517 94.25) + (start 121.7 98.325) + (end 123 97.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "5fdd08e0-3acb-4f03-9b1e-ecad268d0459") + (uuid "b984b8c0-a576-4b03-adfb-26b7bbab121d") ) (segment - (start 128.8017 94.25) - (end 128.9105 94.25) + (start 124.65 102.975) + (end 123.025 102.975) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "76a94796-5766-471c-b611-b6ab14f2544c") + (uuid "c9895502-f2b6-4148-a983-9cfecb05ac6b") ) (segment - (start 128.9105 94.25) - (end 129.065 94.0955) + (start 125.7 104.025) + (end 124.65 102.975) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "77714d3d-c254-4cb5-bb7a-e875b4494938") + (uuid "d96b8ee8-ac45-4dc0-a7b4-a377a519ad11") ) (segment - (start 124.6517 94.25) - (end 124.68 94.2783) + (start 129.55 109.9) + (end 129.5 109.95) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "87cf210a-d869-495b-94d1-d4fb6866b460") + (uuid "e22d1921-00fe-447e-bca1-29a53424e631") ) (segment - (start 124.68 94.2783) - (end 127.12 94.2783) + (start 130.4 109.9) + (end 129.55 109.9) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "9a4d804d-9dcc-413e-b1f8-6ac457e64ef8") + (uuid "e22fefd4-e535-4e95-a4dd-2b3a26c2c5f9") ) (segment - (start 127.975 94.25) - (end 128.8017 94.25) + (start 128.2 105.450002) + (end 126.774998 104.025) (width 0.2) (layer "F.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "fb3645b0-c21e-448d-b5ef-d34061f0e628") + (uuid "e42bceb4-174b-458d-8178-95c507413051") + ) + (via + (at 128.2 105.450002) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "241ad7b4-0d3d-4e54-bc25-000b3b3e5b8b") ) (via - (at 129.065 94.0955) + (at 130.4 109.9) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "8823e70e-d6bf-49f9-a36d-b01c3a8e0963") + (uuid "2f887ff6-2ab3-44a4-8c13-490e2c1d9e50") + ) + (segment + (start 128.2 105.450002) + (end 128.2 108.2) + (width 0.2) + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO1") + (uuid "182b6d88-6d3b-4d99-a8b5-2a7aa357f352") ) (segment - (start 131.025 94.7) - (end 130.4205 94.0955) + (start 129.9 109.9) + (end 130.4 109.9) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "a39cb79e-4dd4-4f1a-b7c6-d7ae9626b8c2") + (uuid "6fb315b6-be8b-4bfd-9e95-d98b6b291e62") ) (segment - (start 130.4205 94.0955) - (end 129.065 94.0955) + (start 128.2 108.2) + (end 129.9 109.9) (width 0.2) (layer "B.Cu") (net "/Buttons_Direct/BTN_MACRO1") - (uuid "d9601574-2271-49ae-a574-0670727fc574") + (uuid "a91c699f-cd48-4678-9de8-27f67818b5f6") ) (segment - (start 131.0141 126.5467) - (end 131.0141 125.8909) + (start 127.85 125.35) + (end 127.85 123.55) (width 0.2) (layer "F.Cu") (net "/RGB_LED/RGB_DIN_R") - (uuid "07799de1-4154-4b8b-9065-88e47ffbd858") + (uuid "0c9b559e-e937-4ec1-b956-66b265d15524") ) (segment - (start 127.8753 121.9647) - (end 127.24 122.6) + (start 127.85 123.55) + (end 127.9 123.5) (width 0.2) (layer "F.Cu") (net "/RGB_LED/RGB_DIN_R") - (uuid "08ac7f0b-94c8-477e-b3a4-91d21fb4993b") + (uuid "af17e32d-0146-4052-bd44-dfdb46194958") ) (segment - (start 127.85 125.35) - (end 129.5 127) + (start 121.55 116.098529) + (end 124.2 113.448529) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "5f625e53-e6d3-40f6-805d-5ae45da4c03d") + (net "/Accelerometer/I2C_SDA") + (uuid "06ccf7a9-1b92-4eda-9100-ed2b526a1e4f") ) (segment - (start 131.0141 125.8909) - (end 130.5385 125.4153) + (start 121.874741 124.680758) + (end 121.55 124.356017) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "628460de-b7ee-4cbf-a7ae-19f5943993a5") + (net "/Accelerometer/I2C_SDA") + (uuid "16aed1cb-b7f1-44f8-9565-0dca2d6fc8a4") ) (segment - (start 130.5385 123.5138) - (end 128.9894 121.9647) + (start 126 105.8) + (end 125.5 106.3) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "7fec1f50-e9c7-419a-9546-246c9af34845") + (net "/Accelerometer/I2C_SDA") + (uuid "68a1cd5e-866d-4800-8d87-939b60d96b15") ) (segment - (start 130.5608 127) - (end 131.0141 126.5467) + (start 129.5 106.55) + (end 128.298924 106.55) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "a033e3ec-013f-4e24-9a12-bcb9eb3df064") + (net "/Accelerometer/I2C_SDA") + (uuid "6da624dd-9345-4251-b6b8-a091168a7f64") ) (segment - (start 130.5385 125.4153) - (end 130.5385 123.5138) + (start 124.2 113.448529) + (end 124.2 111.6) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "a314768d-294c-4ed0-a8bd-907ff822acdc") + (net "/Accelerometer/I2C_SDA") + (uuid "75eb755a-9f0d-4df5-952c-4ec4cf3ee1ef") ) (segment - (start 129.5 127) - (end 130.5608 127) + (start 124.9 106.9) + (end 124.9 108.125) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "b48c8109-db89-4280-89b3-a9da5c843e3a") + (net "/Accelerometer/I2C_SDA") + (uuid "7ee0b0c9-4b61-4ceb-82ba-959455219c8a") ) (segment - (start 128.9894 121.9647) - (end 127.8753 121.9647) + (start 121.55 124.356017) + (end 121.55 116.098529) (width 0.2) (layer "F.Cu") - (net "/RGB_LED/RGB_DIN_R") - (uuid "dbb15a93-0280-4693-9232-5a40a3295dc9") + (net "/Accelerometer/I2C_SDA") + (uuid "cb2a0c7e-1ccf-4c72-9fed-86bc8e423818") ) (segment - (start 133.25 117.54) - (end 132.075 118.715) - (width 0.3) + (start 124.6 109.8) + (end 124.6 108.425) + (width 0.2) (layer "F.Cu") - (net "VBAT") - (uuid "2a95ba59-d379-4775-854d-ffbd8d6c4f91") + (net "/Accelerometer/I2C_SDA") + (uuid "d12e26c4-6c3e-498a-af84-9a1ace03a05d") ) (segment - (start 132.075 118.715) - (end 130.8 118.715) + (start 124.6 108.425) + (end 124.9 108.125) (width 0.2) (layer "F.Cu") - (net "VBAT") - (uuid "2fc0d456-7cc6-44ae-990b-65188d4f5584") + (net "/Accelerometer/I2C_SDA") + (uuid "d490ad2a-64ef-48f1-9dd0-4880ea066ed6") ) (segment - (start 133.25 116.815) - (end 133.25 117.54) - (width 0.3) + (start 127.548924 105.8) + (end 126 105.8) + (width 0.2) (layer "F.Cu") - (net "VBAT") - (uuid "522f7c54-d379-4c43-aa56-b2366daf1b49") + (net "/Accelerometer/I2C_SDA") + (uuid "d82b63e6-d7c1-4784-be7b-0aacead8c736") ) (segment - (start 133.7178 118.9374) - (end 133.8106 118.9374) - (width 0.4) + (start 125.5 106.3) + (end 124.9 106.9) + (width 0.2) (layer "F.Cu") - (net "VBAT") - (uuid "629580dd-ab4f-4811-880a-c3e59761b95e") + (net "/Accelerometer/I2C_SDA") + (uuid "da0bcd6e-e4cd-4976-a96c-09a58b4a19f3") ) (segment - (start 132.7852 118.0048) - (end 133.7178 118.9374) - (width 0.4) + (start 128.298924 106.55) + (end 127.548924 105.8) + (width 0.2) (layer "F.Cu") - (net "VBAT") - (uuid "f30eb79a-cf23-4a9e-ab79-eb3b4db54d33") + (net "/Accelerometer/I2C_SDA") + (uuid "eb5f2b0d-6928-4ab4-afb8-7b6705f129ab") ) (via - (at 133.8106 118.9374) + (at 124.2 111.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "VBAT") - (uuid "3db0ae5a-98ed-4e1b-acca-0d143443dd58") + (net "/Accelerometer/I2C_SDA") + (uuid "514da706-bbab-4a13-90b8-1d5f4673eb33") + ) + (via + (at 124.6 109.8) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "578a95e1-45f4-440e-816f-ec2e5426ceea") + ) + (via + (at 121.874741 124.680758) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "e87b5d5d-54a2-400d-aa00-a3d7576f1d36") ) (segment - (start 134.4346 119.5614) - (end 133.8106 118.9374) - (width 0.4) + (start 125.684557 126.7625) + (end 125.422057 126.5) + (width 0.2) (layer "B.Cu") - (net "VBAT") - (uuid "698242ea-4f4b-47b3-be7b-65f4ec10fb4b") + (net "/Accelerometer/I2C_SDA") + (uuid "562ca885-1be0-4997-b35e-0ea0cb4f1720") ) (segment - (start 141.6614 119.5614) - (end 134.4346 119.5614) - (width 0.4) + (start 125.422057 126.5) + (end 121.8 126.5) + (width 0.2) (layer "B.Cu") - (net "VBAT") - (uuid "a8c32e5b-3db3-48a0-ae05-0d6a011c6985") + (net "/Accelerometer/I2C_SDA") + (uuid "869e6e0d-9562-48ae-8e82-5993e052f76d") ) (segment - (start 145.2 123.1) - (end 141.6614 119.5614) - (width 0.4) + (start 124.2 110.2) + (end 124.6 109.8) + (width 0.2) (layer "B.Cu") - (net "VBAT") - (uuid "db401caf-de2a-411d-98ab-f1aa7d34002b") + (net "/Accelerometer/I2C_SDA") + (uuid "a0926104-794b-4a36-a2e5-e6dcc5236d11") ) (segment - (start 129.8448 112.9018) - (end 129.8448 103.3569) + (start 124.2 111.6) + (end 124.2 110.2) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "42c7f9ad-2299-43b9-b624-ab20c64dd62b") + (layer "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "c4a8b6f3-fb75-4ffd-8841-f85ad3970acb") + ) + (segment + (start 121.8 126.5) + (end 121.8 124.755499) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "dacea946-30ae-466c-8ab4-94804935741d") + ) + (segment + (start 121.8 124.755499) + (end 121.874741 124.680758) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "dc0a449b-6bf4-42d6-a87a-0228ef482600") + ) + (segment + (start 128.9 126.7625) + (end 125.684557 126.7625) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SDA") + (uuid "ea5ffd77-b2eb-44ef-b1fb-9be90aefee53") ) (segment - (start 132.45 117.430686) - (end 132.45 115.905) + (start 125.8 108.225) + (end 125.9 108.125) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "5ed7f34e-a786-4a1b-99b9-a27d9e8ffed1") + (net "/Accelerometer/I2C_SCL") + (uuid "03086db0-eac7-432e-81bc-f4ed026b7ae3") ) (segment - (start 130.4731 96.5856) - (end 130.3875 96.5) + (start 121.1 115.7) + (end 122.7 114.1) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "67962234-1b51-4c6f-b83f-b5b292f1ae13") + (net "/Accelerometer/I2C_SCL") + (uuid "25909493-96db-4c24-9a6e-fd9158f678b5") ) (segment - (start 131.565686 118.315) - (end 132.45 117.430686) + (start 126.615 107.41) + (end 125.9 108.125) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "6c7a7052-9db3-4a3c-bb18-787879e1200e") + (net "/Accelerometer/I2C_SCL") + (uuid "3e9553ac-d83a-4497-87db-c4ee81c4c71d") ) (segment - (start 132.45 115.905) - (end 133.84 114.515) + (start 127.2 107.41) + (end 126.615 107.41) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "89d900f1-52e1-4e44-ba9c-64abd220fe40") + (net "/Accelerometer/I2C_SCL") + (uuid "4bb8d76a-5476-4fa8-8d78-358e010a6a26") ) (segment - (start 130.8 118.315) - (end 131.565686 118.315) + (start 121.1 124.88021) + (end 121.1 115.7) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "bb0031fe-b79f-4f60-98ef-956df8c39315") + (net "/Accelerometer/I2C_SCL") + (uuid "597a0e55-201c-42c3-b714-8ec4d84b0f83") ) (segment - (start 130.4731 102.7286) - (end 130.4731 96.5856) + (start 127.21 107.4) + (end 127.2 107.41) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "e4157acb-8b3b-44bd-9fe8-dacc441f20eb") + (net "/Accelerometer/I2C_SCL") + (uuid "bf98788c-a04b-4be1-8a50-30e25cbbfb84") ) (segment - (start 129.8448 103.3569) - (end 130.4731 102.7286) + (start 129.5 107.4) + (end 127.21 107.4) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "e57cc634-8748-4e80-bd84-890a48911af8") + (net "/Accelerometer/I2C_SCL") + (uuid "cc6cd95c-b417-4dbc-ae2e-0231d364e32d") ) (segment - (start 132.649 115.706) - (end 129.8448 112.9018) + (start 125.8 109.7) + (end 125.8 108.225) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT2") - (uuid "f30da58d-a633-4fcb-803d-18ea2ab5bf99") + (net "/Accelerometer/I2C_SCL") + (uuid "d2e1fde5-cf3d-4733-956d-54456180b413") ) (via - (at 130.3875 96.5) + (at 125.8 109.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/STAT2") - (uuid "f5a7af59-011c-4839-98ee-4b77761c97d0") + (net "/Accelerometer/I2C_SCL") + (uuid "77189360-0ecb-49a8-b9d9-069ba18fdd1a") + ) + (via + (at 122.7 114.1) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "9c6d63e6-b607-48db-804a-d9b2d906a0f7") + ) + (via + (at 121.1 124.88021) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "c8099b9d-7a3b-4e38-9c4b-569aa6b2fb26") ) (segment - (start 131.025 95.9) - (end 130.425 96.5) + (start 121.35 127.05) + (end 121.3 127.1) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STAT2") - (uuid "6f481f2d-acff-4f62-a060-19b4f3b9eb70") + (net "/Accelerometer/I2C_SCL") + (uuid "042d32f0-0548-463b-973c-7ba401f40c00") ) (segment - (start 130.425 96.5) - (end 130.3875 96.5) + (start 128.9 127.2625) + (end 128.875 127.2375) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STAT2") - (uuid "787f9cff-6da4-49c4-b524-fb81b3e805af") + (net "/Accelerometer/I2C_SCL") + (uuid "0dfdcb99-b537-4875-b379-1b99373e245f") + ) + (segment + (start 128.875 127.2375) + (end 128.512068 127.2375) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "137c5b21-1d4e-4b52-8482-0ae8ad12ffe0") + ) + (segment + (start 121.3 125.08021) + (end 121.1 124.88021) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "1da521ca-5896-4104-8f30-5d0e36fbdb93") + ) + (segment + (start 121.3 127.1) + (end 121.3 125.08021) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "24223da9-d997-453c-8bea-08c17435308e") + ) + (segment + (start 125.518871 127.1625) + (end 125.406372 127.05) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "3be2ecd8-8fd8-4d32-9535-abb206ea0ace") + ) + (segment + (start 128.512068 127.2375) + (end 128.437068 127.1625) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "88bab3a6-e187-471e-8ffb-f075a7ce5a3a") + ) + (segment + (start 128.437068 127.1625) + (end 125.518871 127.1625) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "92423a91-cb83-4049-b1b5-1b1edc00be7d") + ) + (segment + (start 125.8 111) + (end 125.8 109.7) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "aa5678c3-3775-4a9e-a795-a0ae70cd6d34") + ) + (segment + (start 125.406372 127.05) + (end 121.35 127.05) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "db1d8758-19c7-4908-b518-2a821e461fe8") + ) + (segment + (start 122.7 114.1) + (end 125.8 111) + (width 0.2) + (layer "B.Cu") + (net "/Accelerometer/I2C_SCL") + (uuid "e6500747-4256-47fe-8dce-77c5e5bf3206") ) (segment - (start 126.435 114.5) - (end 122.77 114.5) + (start 139.05 106.05) + (end 138.9 106.2) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_TS") - (uuid "0212afc8-72c8-4767-ad16-7d2e2553e1dc") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "655b1062-2eec-430c-b433-7b70f57ff75b") ) (segment - (start 128.7 116.765) - (end 128.7 117.515) + (start 139.05 105.5) + (end 139.05 106.05) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_TS") - (uuid "0bdd8bee-6d2e-45c5-be2f-81543a6adb6c") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "ffc67b28-fc43-494e-98cb-39fae2293f4b") + ) + (via + (at 138.9 106.2) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "215021d9-a964-4baa-88bb-e367c3658bd9") + ) + (segment + (start 139.15 105.95) + (end 139.15 103.6) + (width 0.2) + (layer "B.Cu") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "331193a9-bb7b-4a1e-ad89-4b1dc59ab951") + ) + (segment + (start 138.9 106.2) + (end 139.15 105.95) + (width 0.2) + (layer "B.Cu") + (net "/XBee/XBEE_SLEEP_RQ") + (uuid "7e57f38d-a598-416e-86e2-ec7774bbd1f0") ) (segment - (start 128.7 116.765) - (end 126.435 114.5) + (start 131.4 93.051471) + (end 133.948529 93.051471) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_TS") - (uuid "8906018a-b534-4811-a33e-a7ccc6df157a") + (net "/MCU_Core/STICK_Y") + (uuid "1af9a623-1ae8-4c9f-8411-d4bdd881b772") ) (segment - (start 127.184314 115.815) - (end 127.75 116.380686) + (start 139.675 83.659745) + (end 139.2 83.184745) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "362da563-4eb8-4cd7-8b3d-5b573fa220a4") + (net "/MCU_Core/STICK_Y") + (uuid "292d281e-18ab-450f-a1fc-4a1badbcb98e") ) (segment - (start 127.75 116.380686) - (end 127.75 116.419756) + (start 141.7 90.798529) + (end 141.7 86.425) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "5340af3e-6748-4f16-9061-189faeedca80") + (net "/MCU_Core/STICK_Y") + (uuid "2d3562d5-5159-4c86-8bd3-5dc95d1798ea") ) (segment - (start 122.77 115.5) - (end 122.805 115.465) + (start 141.984745 78.5) + (end 143.73 78.5) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "65501ebe-80f5-4b0f-8296-dc65ba0d5560") + (net "/MCU_Core/STICK_Y") + (uuid "38230c5c-1095-4205-a7ca-61244c7d8a75") ) (segment - (start 128.25 117.219756) - (end 128.15 117.319756) + (start 139.2 83.184745) + (end 139.2 81.284745) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "65cdb2e4-c656-48ee-b235-bf82ae71bded") + (net "/MCU_Core/STICK_Y") + (uuid "60b82cc3-c86b-47b5-a62b-3fb72aa95d53") ) (segment - (start 126.75 115.815) - (end 127.184314 115.815) + (start 135.1 91.9) + (end 140.598529 91.9) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "7bc1c663-818e-4ff7-89f2-81b9201b8321") + (net "/MCU_Core/STICK_Y") + (uuid "709cbd7c-2c44-4019-bf86-fbdb90b02c4a") ) (segment - (start 126.4 115.465) - (end 126.75 115.815) + (start 131.35 95.498529) + (end 131.35 93.101471) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "87e7ba11-e065-4f58-b388-81dfefa02ec9") + (net "/MCU_Core/STICK_Y") + (uuid "77f361eb-9fcd-43a2-9d1d-ccd276697583") ) (segment - (start 128.354756 117.915) - (end 128.7 117.915) + (start 131.35 93.101471) + (end 131.4 93.051471) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "90d3d392-81d5-4144-826e-6862da3a5751") + (net "/MCU_Core/STICK_Y") + (uuid "7a049694-1bcd-4cbc-a7e6-2ff0dc66e4ee") ) (segment - (start 127.75 116.419756) - (end 128.25 116.919756) + (start 134.8 105.5) + (end 134.8 104.3) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "9ec8214c-a997-405b-9914-440e222e4fb8") + (net "/MCU_Core/STICK_Y") + (uuid "7afb1bc0-154c-449f-9370-af0d9a65213b") ) (segment - (start 122.805 115.465) - (end 126.4 115.465) + (start 133.948529 93.051471) + (end 135.1 91.9) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "e32e00b4-f8c0-4a80-9749-083b962e649e") + (net "/MCU_Core/STICK_Y") + (uuid "7d470682-8364-45e4-9797-7502a9233635") ) (segment - (start 128.25 116.919756) - (end 128.25 117.219756) + (start 141.7 86.425) + (end 139.675 84.4) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "ef4dd42b-965c-4914-8c1b-93cd74441cbf") + (net "/MCU_Core/STICK_Y") + (uuid "7d75e0b0-902b-4884-839c-0b41786b179b") ) (segment - (start 128.15 117.319756) - (end 128.15 117.710244) + (start 140.598529 91.9) + (end 141.7 90.798529) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "efac241c-abf4-414e-a689-07d0782b1505") + (net "/MCU_Core/STICK_Y") + (uuid "87e39e77-5b4e-48c1-b393-b0af3f82caed") ) (segment - (start 128.15 117.710244) - (end 128.354756 117.915) + (start 134.4 103.9) + (end 134.4 99.535785) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_VSET") - (uuid "f31cec17-dea3-4202-ba4b-5f77ee43ebb5") + (net "/MCU_Core/STICK_Y") + (uuid "8ce02a6f-6b18-4ba2-b1db-8ceed3392daf") ) (segment - (start 127.75 117.87593) - (end 128.189071 118.315) + (start 134.4 99.535785) + (end 131.5 96.635785) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "048ba200-021d-4043-a915-a8363537111c") + (net "/MCU_Core/STICK_Y") + (uuid "93399da4-8bd4-4666-89db-5cad9054d5db") ) (segment - (start 127.35 116.546372) - (end 127.35 116.585442) + (start 131.5 96.635785) + (end 131.5 95.648529) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "1535a58f-c023-4309-a693-f0d3d7cc1736") + (net "/MCU_Core/STICK_Y") + (uuid "a676b04c-6efb-47e5-82da-da5f755c8cce") ) (segment - (start 126.098529 116.315) - (end 127.118628 116.315) + (start 134.8 104.3) + (end 134.4 103.9) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "1965ef4d-47a7-42d0-b7f4-2fef3a5fd083") + (net "/MCU_Core/STICK_Y") + (uuid "ac134e10-7bc6-418f-8c11-4b981ba56359") ) (segment - (start 127.75 116.985442) - (end 127.75 117.87593) + (start 131.5 95.648529) + (end 131.35 95.498529) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "1c912556-565d-409a-93a2-f0945a4dd345") + (net "/MCU_Core/STICK_Y") + (uuid "b326013d-d744-42ae-86c8-0ebc7b206a37") ) (segment - (start 125.748529 116.665) - (end 126.098529 116.315) + (start 139.675 84.4) + (end 139.675 83.659745) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "40ac8fed-f7a5-4c0c-8bdb-7a5d47674219") + (net "/MCU_Core/STICK_Y") + (uuid "cbf4e759-0e44-464e-b2d8-e7cacab1bf52") ) (segment - (start 127.35 116.585442) - (end 127.75 116.985442) + (start 139.2 81.284745) + (end 141.984745 78.5) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "48a88625-826f-448e-872d-8f2fde7f0841") + (net "/MCU_Core/STICK_Y") + (uuid "d6c4ca87-5335-44da-a7f3-032acb9ac5af") ) (segment - (start 128.189071 118.315) - (end 128.7 118.315) + (start 131 92.734314) + (end 133.5 90.234314) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "4a5ecd4f-7cbc-4ffe-b321-c2855ef724ac") + (net "/MCU_Core/STICK_X") + (uuid "10fb9a6b-5a9f-410b-8837-7e71149bd0ed") ) (segment - (start 127.118628 116.315) - (end 127.35 116.546372) + (start 131 95.714215) + (end 130.95 95.664214) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "4fb04146-3854-4ed5-8778-79b6719e67ae") + (net "/MCU_Core/STICK_X") + (uuid "1d2cb48f-7c67-4353-ab32-211c67af8215") ) (segment - (start 122.99 116.315) - (end 122.79 116.515) + (start 134 105.199999) + (end 134 99.701471) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "790a360f-78a4-4332-b6b3-bdbbf5db425b") + (net "/MCU_Core/STICK_X") + (uuid "23e0abfe-acda-4ce6-905b-98f9a8af0d18") ) (segment - (start 125.251471 116.665) - (end 125.748529 116.665) + (start 133.5 80.626471) + (end 133.5 72.573529) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "cc016f12-fd0c-481a-92c0-69e55ea1a2b1") + (net "/MCU_Core/STICK_X") + (uuid "2cb198d0-41b0-4c6d-a4ab-92f71c29a8dc") ) (segment - (start 124.901471 116.315) - (end 122.99 116.315) + (start 133.5 81.253529) + (end 133.435 81.188529) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "da19cf87-c189-449b-8cb1-385da660bd97") + (net "/MCU_Core/STICK_X") + (uuid "4d3fed99-3cab-4e80-87dc-e7271b3a7486") ) (segment - (start 124.901471 116.315) - (end 125.251471 116.665) + (start 133.949999 105.25) + (end 134 105.199999) (width 0.2) (layer "F.Cu") - (net "/Power_Charger/CHG_ISET") - (uuid "ec76e46b-40b6-4f83-8590-27bce1cabbe3") + (net "/MCU_Core/STICK_X") + (uuid "5318554e-4fe4-46ff-8fdc-5bc5c3851f96") ) (segment - (start 123.825735 117.590735) - (end 124.325 118.09) + (start 130.95 92.935785) + (end 131 92.885786) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "03d9ebfb-3c66-49d1-9987-541e0a326b71") + (net "/MCU_Core/STICK_X") + (uuid "57090677-c1e3-45c0-b10f-e44370133b2c") ) (segment - (start 124.325 118.09) - (end 124.895 118.09) + (start 131 96.70147) + (end 131 95.714215) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "5aa499b5-eb9f-49e3-a32c-b76836bf8247") + (net "/MCU_Core/STICK_X") + (uuid "5b9dd319-d286-46f7-ba01-fa4dfe3ef88a") ) (segment - (start 128.023386 118.715) - (end 127.35 118.041615) + (start 133.5 72.573529) + (end 135 71.073529) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "5c047727-26b6-4fb0-bd66-f877ca158787") + (net "/MCU_Core/STICK_X") + (uuid "758b6f73-e9be-4e2b-a9cc-6f82f02c8055") ) (segment - (start 123.374265 117.590735) - (end 123.825735 117.590735) + (start 133.949999 105.5) + (end 133.949999 105.25) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "66107005-f283-4a28-9a94-02696fecf817") + (net "/MCU_Core/STICK_X") + (uuid "7ab233e1-d7b8-4b46-8e5b-92a3a4ed19e9") + ) + (segment + (start 135 71.073529) + (end 135 69.77) + (width 0.2) + (layer "F.Cu") + (net "/MCU_Core/STICK_X") + (uuid "8004de7d-14b5-4038-8117-048089b4c01b") ) (segment - (start 128.7 118.715) - (end 128.023386 118.715) + (start 131 92.885786) + (end 131 92.734314) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "6e50da04-73fb-4672-b1a9-62a09ac87dab") + (net "/MCU_Core/STICK_X") + (uuid "83c4eaba-d32f-479a-8652-e718dbb8a8c9") ) (segment - (start 125.67 117.315) - (end 124.895 118.09) + (start 134 99.701471) + (end 131 96.70147) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "a6d016fb-f65f-478a-962e-703dfa9d85a6") + (net "/MCU_Core/STICK_X") + (uuid "a4dba125-1570-4562-921e-399a3a760865") ) (segment - (start 125.67 117.315) - (end 126.77 117.315) + (start 133.5 90.234314) + (end 133.5 81.253529) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "ab7a96a5-dfb7-48bd-b12a-404bcb538758") + (net "/MCU_Core/STICK_X") + (uuid "b014ef49-842f-4c77-9403-06fbf2f82259") ) (segment - (start 127.35 117.895) - (end 126.77 117.315) + (start 133.435 81.188529) + (end 133.435 80.691471) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "b4cce019-9ead-4198-b716-304ae6e55ce6") + (net "/MCU_Core/STICK_X") + (uuid "becf7016-d80c-49e8-855a-d0195b88872e") ) (segment - (start 127.35 118.041615) - (end 127.35 117.895) + (start 130.95 95.664214) + (end 130.95 92.935785) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STAT1") - (uuid "d9df9eff-fd9a-436f-902c-f50dc38fc02c") + (net "/MCU_Core/STICK_X") + (uuid "c508c5ca-659e-49c5-b342-f8d5fb45c421") ) - (via - (at 123.374265 117.590735) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "4a466f50-bc7a-43b6-b8b8-bf93e1140e45") + (segment + (start 133.435 80.691471) + (end 133.5 80.626471) + (width 0.2) + (layer "F.Cu") + (net "/MCU_Core/STICK_X") + (uuid "fe11cbcc-970d-4c03-a3f5-86b3c799dbb9") ) (segment - (start 129.0143 101.9856) - (end 129.0143 97.9646) + (start 136.161765 101.138235) + (end 136.763235 101.138235) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "1cdb3883-d706-444f-a935-0f225cdf34fe") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "2527401b-123c-444d-83f0-8da092d748af") ) (segment - (start 123.2299 117.4469) - (end 123.2299 109.6196) + (start 136.763235 101.138235) + (end 137.075 101.45) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "55ab7bcf-54e6-413d-a2cc-00c72e0b0725") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "25acd6cd-b122-43d3-8618-df6e6d3d79dd") ) (segment - (start 129.3928 102.3641) - (end 129.0143 101.9856) + (start 133.3 100.8) + (end 133.3 101.075) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "705703b1-f55c-4319-b064-5f9d299fce58") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "732636c9-0bd5-4b83-9054-39b9f44d11bc") ) (segment - (start 129.0143 97.9646) - (end 129.5084 97.4705) + (start 133.1 105.5) + (end 133.1 107) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "7698d60f-fdb9-4099-ada2-65b6c42089ea") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "d31dd67c-d4ec-43e7-8634-6274179cddd1") ) (segment - (start 123.374 117.591) - (end 123.2299 117.4469) + (start 133.3 101.075) + (end 132.925 101.45) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "c4f8f1d1-1fc7-41eb-a775-82ed7e60d1bd") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "d7c9784a-9ea4-4128-a3d7-dd0090fcc7eb") ) (segment - (start 130.6545 97.4705) - (end 131.025 97.1) + (start 133.1 105.3) + (end 133.1 105.5) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "d658b857-f5aa-496f-992c-ec873832f9e1") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "ef5bcfc7-2ac2-45dd-88bf-d2bbb58ac05e") + ) + (via + (at 133.3 100.8) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "281f7cb5-d2cc-4a80-941a-df3092978bb9") + ) + (via + (at 133.1 107) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "363df623-175d-42be-a353-03ee7c693bb6") + ) + (via + (at 136.161765 101.138235) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "749da11c-a4e1-4d5e-8f59-30d08f112d07") ) (segment - (start 129.3928 103.4567) - (end 129.3928 102.3641) + (start 135.46 102.1) + (end 135.46 101.84) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "e0812533-4798-4ff5-8a6a-384cbeb646f8") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "198211e5-e5e7-4729-b833-eb82e422f73a") ) (segment - (start 129.5084 97.4705) - (end 130.6545 97.4705) + (start 134.16 100.8) + (end 133.3 100.8) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "e51ad566-4892-4904-a9b3-4384a3da9778") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "4b9d8c3a-930a-4bd8-a016-9ca89836219f") ) (segment - (start 123.2299 109.6196) - (end 129.3928 103.4567) + (start 135.46 106.74) + (end 135.46 102.1) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STAT1") - (uuid "ed600cb4-a1e1-43dd-b54e-d28fea2d0302") - ) - (segment - (start 127.3346 75.0086) - (end 127.0942 74.7682) - (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "0aa12448-fe97-4fa0-adb6-f1a84667d85a") - ) - (segment - (start 132.2548 67.2125) - (end 132.2548 65.6521) - (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "5f324d7b-db27-4e5a-a0a1-c23c142845ca") - ) - (segment - (start 127.0942 74.7682) - (end 127.0942 72.3731) - (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "6c0c451c-ce1a-458c-8a39-042ae79d3b64") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "5cfe9479-399f-4510-b477-d8cc8ed7dc41") ) (segment - (start 127.3346 81.6925) - (end 127.3346 75.0086) + (start 135.46 102.1) + (end 134.16 100.8) (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "81e30020-2c15-4759-85bd-cd529ff5cbb8") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "5faf6b9f-5242-493c-b865-8a86d5074d45") ) (segment - (start 127.0942 72.3731) - (end 132.2548 67.2125) + (start 135.2 107) + (end 135.46 106.74) (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "8218612c-c926-4935-817c-c4e5d9a93420") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "7dbdb432-39a4-4e70-9f4c-29b50218ec8e") ) (segment - (start 126.4363 89.1491) - (end 126.4363 82.5908) + (start 135.46 101.84) + (end 136.161765 101.138235) (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "899188b5-226c-4fc4-b0b4-a1736fd9c085") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "b73133bf-d7ad-44df-8eda-25ffa002833a") ) (segment - (start 122.4244 93.161) - (end 126.4363 89.1491) + (start 133.1 107) + (end 135.2 107) (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "924eede7-d160-4237-99e5-f066a02a0e1b") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_MACRO5") + (uuid "be76bae2-4336-4cfc-9aee-897a27e31850") ) (segment - (start 123.2995 102.2515) - (end 122.4244 101.3764) + (start 131.4 105.3) + (end 130.7 104.6) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "9ed9ad8b-42b4-45da-ac31-e7e23bee6e68") + (net "/MCU_Core/VSYS_SENSE") + (uuid "1515e572-3f37-47d4-8521-39818e29cb75") ) (segment - (start 124.9 106.125) - (end 124.9 104.8086) + (start 131.4 105.5) + (end 131.4 105.3) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "a95c59a8-e35a-4d13-9e2b-daef6d4beb95") + (net "/MCU_Core/VSYS_SENSE") + (uuid "37097c76-a213-4de1-9ff9-6719bc3a147e") ) (segment - (start 124.9 104.8086) - (end 124.9596 104.749) + (start 130 102.89) + (end 130 102.12) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "b65f47bd-b7f8-4bb9-beb8-fd05a8fca978") + (net "/MCU_Core/VSYS_SENSE") + (uuid "971ef620-0ee5-49b5-8712-0dfb2e80ee3c") ) (segment - (start 123.7989 102.2515) - (end 123.2995 102.2515) + (start 130.7 103.59) + (end 130 102.89) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "b9247f40-ad48-48d7-b5da-f47e13782339") + (net "/MCU_Core/VSYS_SENSE") + (uuid "a3c6f660-6183-4962-9408-c34eae8b6aa9") ) (segment - (start 124.9596 103.4122) - (end 123.7989 102.2515) + (start 130 102.12) + (end 129.8 101.92) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "dc26abbe-3438-4045-9413-61d4d7606395") + (net "/MCU_Core/VSYS_SENSE") + (uuid "bccde10e-2be7-4722-a161-9ef37c62aa07") ) (segment - (start 124.9596 104.749) - (end 124.9596 103.4122) + (start 130.7 104.6) + (end 130.7 103.59) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "df1573af-13b9-4bf0-824d-3fc046fbd45d") + (net "/MCU_Core/VSYS_SENSE") + (uuid "f20b019d-1bb6-43b5-8f72-cfebcbaccdb0") ) (segment - (start 122.4244 101.3764) - (end 122.4244 93.161) + (start 129.674265 108.075735) + (end 129.5 108.25) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "fdb0db77-a45b-47f1-b075-278117824150") + (net "/MCU_Core/STAT2") + (uuid "4756247f-fd0f-4b8f-8e68-a8a8f4aa8955") ) (segment - (start 126.4363 82.5908) - (end 127.3346 81.6925) + (start 130.824265 108.075735) + (end 129.674265 108.075735) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "ffdb3478-14ad-437f-adbc-a146da20cfcd") - ) - (via - (at 132.2548 65.6521) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "7b567a32-48b3-4df2-aae9-3eb0e92a0fa9") + (net "/MCU_Core/STAT2") + (uuid "81acb96e-58d4-4699-ba10-0840304cba38") ) (via - (at 124.9596 104.749) + (at 130.824265 108.075735) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "ab91a7f9-d58d-4ef9-8ada-59794d33b213") - ) - (segment - (start 125.875 101.99) - (end 126.522 102.637) - (width 0.2) - (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "2cdfbd13-6612-4fb3-9a97-96e5df6d5a51") + (net "/MCU_Core/STAT2") + (uuid "4f15d02d-1a7a-4613-95ce-42bb5fdc92ec") ) (segment - (start 126.365 101.5) - (end 125.875 101.99) + (start 132.84 100.05) + (end 132.7 100.19) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "2e65aed1-efc1-4043-a529-449d3a9d21cd") + (net "/MCU_Core/STAT2") + (uuid "1dd32410-5322-4be9-ab94-c18a836748d0") ) (segment - (start 126.522 102.637) - (end 126.522 103.4077) + (start 131.45 97.134314) + (end 131.45 98.66) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "5150ff60-4119-4cce-8038-307ba056abc5") + (net "/MCU_Core/STAT2") + (uuid "9995abd9-e812-4f0e-ab19-3f7f10d5bbc5") ) (segment - (start 144.5138 65.6521) - (end 132.2548 65.6521) + (start 132.7 100.19) + (end 132.7 105.751471) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "6dd44bcd-efd2-4803-898d-4751416f21c7") + (net "/MCU_Core/STAT2") + (uuid "a7bc0d81-81c7-4f0e-8bf2-e3c919ba6737") ) (segment - (start 145.2 66.8875) - (end 145.2 66.3383) + (start 131.45 98.66) + (end 132.84 100.05) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "6fca7bae-20c5-4cb4-993e-292ddcfa02a1") + (net "/MCU_Core/STAT2") + (uuid "c63c97b1-99c3-4aa7-b182-c7dac676dcf0") ) (segment - (start 125.1807 104.749) - (end 124.9596 104.749) + (start 130.565686 96.25) + (end 131.45 97.134314) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "7d1e9039-56f4-413a-90f9-ede57da9fc64") + (net "/MCU_Core/STAT2") + (uuid "c8f79575-e298-45fa-afb4-115a5a4a644f") ) (segment - (start 126.522 103.4077) - (end 125.1807 104.749) + (start 129.8 96.25) + (end 130.565686 96.25) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "a1f8d9ea-5d29-418a-987b-1cbc63944e27") + (net "/MCU_Core/STAT2") + (uuid "e4a01d75-27ef-4683-ba14-8cede60d9748") ) (segment - (start 127.9 101.5) - (end 126.365 101.5) + (start 130.824265 107.627206) + (end 130.824265 108.075735) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "a70d8ce4-3b63-4cc5-a3a9-9dbaf9f6c80b") + (net "/MCU_Core/STAT2") + (uuid "e891e626-5eb5-4a9c-b067-d73a3611667b") ) (segment - (start 145.2 66.3383) - (end 144.5138 65.6521) + (start 132.7 105.751471) + (end 130.824265 107.627206) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SDA") - (uuid "d16a9da7-dd15-43d7-855a-1fd1ee0b167b") - ) - (segment - (start 125.9 101.2353) - (end 126.7353 100.4) - (width 0.2) - (layer "F.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "85562209-9aa8-4fac-8a35-0eb945c7d99b") + (net "/MCU_Core/STAT2") + (uuid "fc79ee49-ac3b-48ac-8290-2260eb103a64") ) (segment - (start 126.0039 88.8722) - (end 126.0039 70.9951) + (start 130.6 109.1) + (end 130.8 108.9) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "acf610f0-06dc-4587-943a-d711d86d3b26") + (net "/MCU_Core/STAT1") + (uuid "47636305-1589-43df-a604-d41f1b2b1315") ) (segment - (start 121.3278 93.5483) - (end 126.0039 88.8722) + (start 129.5 109.1) + (end 130.6 109.1) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "cf741c58-4021-4249-979c-16f19f099db2") + (net "/MCU_Core/STAT1") + (uuid "a26fc0c2-9527-4230-83c5-349abd43ad6b") ) (segment - (start 121.3278 96.4625) - (end 121.3278 93.5483) + (start 126.15 97.4701) + (end 126.15 97.65) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "ea6b5183-0728-4b6d-860f-8eedaa6de82b") + (net "/MCU_Core/STAT1") + (uuid "acc933d7-cc52-4a25-9c55-7570cb6012b7") ) (segment - (start 125.9 106.125) - (end 125.9 101.2353) + (start 126.15 97.65) + (end 127.5 99) (width 0.2) (layer "F.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "ee3303b4-56c3-4b41-8c49-5adfab10d469") + (net "/MCU_Core/STAT1") + (uuid "cd3a49eb-db2b-499f-99c6-63a91c737bc1") ) (via - (at 121.3278 96.4625) + (at 130.8 108.9) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "4a4cdf55-e76c-4da7-9928-66d6c93f8cbf") + (net "/MCU_Core/STAT1") + (uuid "6e99d32b-1f21-47b2-8975-0f3195c40f46") ) (via - (at 126.0039 70.9951) + (at 127.5 99) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "ae401dcd-1320-42c6-95c6-f74471fd4e96") + (net "/MCU_Core/STAT1") + (uuid "a095a2f8-7f5a-4a4f-85e4-f9c3690aa8aa") ) (via - (at 126.7353 100.4) + (at 126.15 97.4701) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "eeede98d-bd1f-493e-88bb-40229d89c2e7") + (net "/MCU_Core/STAT1") + (uuid "dd0acb73-6c38-415f-8228-7256eb79cd23") ) (segment - (start 127.9 100.4) - (end 126.7353 100.4) + (start 124.67 97.25) + (end 125.9299 97.25) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "0ff5f66a-9b78-4c92-8d3c-1fe8492a32ca") + (net "/MCU_Core/STAT1") + (uuid "02ec0a75-c6bf-42ed-adff-b6d6b75c1fff") ) (segment - (start 125.875 99.74) - (end 126.535 100.4) + (start 130.8 108.9) + (end 130.2 108.3) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "32f37668-905a-4b2d-aafb-67cdd3d0328b") + (net "/MCU_Core/STAT1") + (uuid "0beff254-8c6c-4a16-9c63-164852e56334") ) (segment - (start 144.7 66.4086) - (end 144.3998 66.1084) + (start 130.2 108.3) + (end 130.2 100.951471) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "48112518-da0f-4be9-928b-cef46c3e453f") + (net "/MCU_Core/STAT1") + (uuid "0dbda287-c22a-4ada-8e54-6bc2fef78b36") ) (segment - (start 144.7 66.8875) - (end 144.7 66.4086) + (start 124.67 97.25) + (end 125.77 97.25) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "51e93d59-188f-4a47-9408-ab9047b1463a") + (net "/MCU_Core/STAT1") + (uuid "183cd582-9e9a-4bde-9884-f424aeacd7d0") ) (segment - (start 131.6744 70.9951) - (end 126.0039 70.9951) + (start 127.7 95.85) + (end 127.023386 95.85) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "64a92bc3-7ed3-4bfa-bd47-446c28be7ad9") + (net "/MCU_Core/STAT1") + (uuid "5578920e-0041-4059-b292-f7eea4bbb83b") ) (segment - (start 141.8799 66.1084) - (end 139.223 68.7653) + (start 130.2 100.951471) + (end 128.248529 99) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "65851c4b-04e0-43d0-8382-e72296d44597") + (net "/MCU_Core/STAT1") + (uuid "720a1fd5-54af-4900-b88e-9a224fbf35b6") ) (segment - (start 131.776 71.0967) - (end 131.6744 70.9951) + (start 128.248529 99) + (end 127.5 99) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "8ad653af-595b-416b-b260-3f9bc01fda63") + (net "/MCU_Core/STAT1") + (uuid "8f91aaaf-4516-463e-b764-a99aba137e8f") ) (segment - (start 144.3998 66.1084) - (end 141.8799 66.1084) + (start 125.9299 97.25) + (end 126.15 97.4701) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "9ce820f4-bcac-4f3b-81a6-6249291c954e") + (net "/MCU_Core/STAT1") + (uuid "b2f8e402-7893-45c2-8951-1abb3129d5c2") ) (segment - (start 126.535 100.4) - (end 126.7353 100.4) + (start 126.35 96.523385) + (end 126.35 96.67) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "ba4f815e-925b-487d-b18c-d3d0b317e055") + (net "/MCU_Core/STAT1") + (uuid "e0605dd5-13ee-4ed9-954c-7bbc3df9b4ac") ) (segment - (start 139.223 68.7653) - (end 139.223 69.9302) + (start 126.35 96.67) + (end 125.77 97.25) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "c0f2a696-e851-48e0-9244-cf948e76098c") + (net "/MCU_Core/STAT1") + (uuid "e6345ba6-5af8-4134-8d8f-5e92c063debf") ) (segment - (start 138.0565 71.0967) - (end 131.776 71.0967) + (start 127.023386 95.85) + (end 126.35 96.523385) (width 0.2) (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "cb91ab95-a9fb-4fba-9d47-fc2bcc11de00") + (net "/MCU_Core/STAT1") + (uuid "f2793c1f-6b04-4827-a271-4f6cbf649c99") ) (segment - (start 139.223 69.9302) - (end 138.0565 71.0967) + (start 129.1 94.35) + (end 129.2 94.45) (width 0.2) - (layer "B.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "f2793926-f35d-4c9d-aea7-d12e87e95737") + (layer "F.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "01221d40-4729-4496-827e-fd3e868cd506") ) (segment - (start 121.3278 96.4625) - (end 122.7978 96.4625) + (start 126.969163 100.4) + (end 126.6 100.4) (width 0.2) - (layer "In1.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "09b9d664-5d26-44b9-889b-b6e7a7b28aec") + (layer "F.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "09bdcbe2-dc55-4478-8b2c-a80aaec36f34") ) (segment - (start 122.7978 96.4625) - (end 126.7353 100.4) + (start 128.734582 98.634582) + (end 126.969163 100.4) (width 0.2) - (layer "In1.Cu") - (net "/Accelerometer/I2C_SCL") - (uuid "6584d171-c78b-4361-989f-b25fc95cc58b") + (layer "F.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "185652f4-81a4-4dc8-957c-bb434f4187e4") ) (segment - (start 133.23 106.67) - (end 133.5 106.4) + (start 130.5 110.8) + (end 129.5 110.8) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "03cb3b49-3a4d-4ef7-90d6-3cd3ef9ad118") + (net "/MCU_Core/BTN_STICK") + (uuid "7ef506ed-9119-47a4-b5da-e797af2da283") ) (segment - (start 135.45 106.25) - (end 135.4 106.2) + (start 131.75 84.25) + (end 129.1 86.9) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "05cc194d-a1f8-4b62-a248-7cad490a270f") + (net "/MCU_Core/BTN_STICK") + (uuid "856a466b-bdda-4cc6-943c-0b89549adfc1") ) (segment - (start 142.45 110.6) - (end 142.5 110.55) + (start 129.1 86.9) + (end 129.1 94.35) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "07a83b93-e7c9-4bc9-92f9-80a394f19d18") + (net "/MCU_Core/BTN_STICK") + (uuid "c6db10aa-5f48-46bc-93e9-b738fd1c85a3") ) (segment - (start 140.95 108.2) - (end 140.8 108.05) + (start 129.2 94.45) + (end 129.2 98.169164) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "2aa38185-9bfc-48ed-b2c8-e320776b2872") + (net "/MCU_Core/BTN_STICK") + (uuid "cfa1b3fb-789f-46a1-9627-057b9a3d8a2e") ) (segment - (start 135.6 106.3) - (end 135.55 106.3) + (start 129.2 98.169164) + (end 128.734582 98.634582) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "2d429bb5-3c18-4620-a31f-c6a2919680fe") + (net "/MCU_Core/BTN_STICK") + (uuid "d59c6e16-83f2-4b52-b33f-50a529c63e5e") ) - (segment - (start 132.655 106.15) - (end 133.23 106.725) - (width 0.3) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "39639a1d-fa87-4ab4-aa2a-35a56018d4fa") + (via + (at 130.5 110.8) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "8a8daf09-9030-4717-b2f0-0f8a1df74738") + ) + (via + (at 126.6 100.4) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "cdfdca5e-0baa-4cdd-91a3-47e2400e9584") ) (segment - (start 141.65 111.45) - (end 142.45 110.65) + (start 124.482927 106.582927) + (end 125.048613 106.582927) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "39b03065-f7ff-4b16-86cd-11aec3ef1b82") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "489045ad-48b7-4a04-83e5-5c55f278ea96") ) (segment - (start 143.45 109) - (end 143.45 108.55) + (start 124.35 106.45) + (end 124.482927 106.582927) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "3baaec77-6bf3-4225-a4df-8745ee08a2fc") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "784ad496-e435-4f03-90d4-56d2479bbbb8") ) (segment - (start 139.45 107.95) - (end 138.75 107.25) + (start 126.6 100.4) + (end 124.35 102.65) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "3f3bec67-9e69-418b-8c6d-122734981663") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "8828b1c4-dfaf-42d5-9809-117a4535ab4e") ) (segment - (start 143.05 108.25) - (end 143 108.2) + (start 124.35 102.65) + (end 124.35 106.45) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "46cc1d5d-d4f2-4ed5-86e9-fbbf6ba6df65") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "b6685ddf-e877-4561-ba5d-ca29f698d0e5") ) (segment - (start 133.23 106.725) - (end 133.23 106.67) + (start 129.265686 110.8) + (end 130.5 110.8) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "488445af-d341-4ae3-ae82-047c1a77d645") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "d8ab78ec-753e-406a-991c-612a38f47a39") ) (segment - (start 141.875 111.225) - (end 141.875 112.075) + (start 125.048613 106.582927) + (end 129.265686 110.8) (width 0.2) - (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "4f06b524-9014-48be-a71a-833ad576a7e3") + (layer "B.Cu") + (net "/MCU_Core/BTN_STICK") + (uuid "faaa0231-7194-45be-b932-b57b3eaac7e5") ) (segment - (start 136.55 107.25) - (end 135.6 106.3) + (start 120.5 98.000001) + (end 120.5 108.6) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "503359a8-2063-4735-b2a9-b783751abe7a") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "0f16e99c-608c-43a9-9a06-57f3e41a73e3") ) (segment - (start 143.45 108.55) - (end 143.15 108.25) + (start 120.5 108.6) + (end 122.7 110.8) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "56592887-b9cf-4ff6-af01-72edb938e209") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "1b0a2383-9fb9-4c4e-b009-79212402ab5e") ) (segment - (start 135.5 106.25) - (end 135.45 106.25) + (start 122.325 82.275) + (end 122.7 82.275) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "58542246-9fb5-4e71-9c3a-40f90a9818ea") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "24d2f083-f7dc-4324-bfbd-d2696c159c10") ) (segment - (start 143.4 109.05) - (end 143.45 109) + (start 128.45 110.8) + (end 129.3 111.65) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "5cf18c95-f30b-452f-bc7e-aa91b74c53a0") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "27ee0abe-92c8-411d-9eba-ac3d33b07481") ) (segment - (start 143.15 108.25) - (end 143.05 108.25) + (start 121.1 83.5) + (end 122.325 82.275) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "5ebd60cc-6c9c-47bc-b408-058f31930d7e") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "2f9e47e0-b284-4510-9cfb-3b3f0af22033") ) (segment - (start 140.55 108) - (end 140.5 107.95) + (start 122.7 85.856371) + (end 120.4 88.156371) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "630257b2-8f0e-40cb-8923-0ac863a9d342") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "3ff76566-03a7-4a4f-8113-603d3f92fad7") ) (segment - (start 134.65 106.1) - (end 133.8 106.1) + (start 120.4 88.156371) + (end 120.4 97.900001) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "6cebe436-c751-41dd-b5ec-29d463f3b480") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "4104d4c9-52aa-4d85-bcad-deb5b9fd55e7") ) (segment - (start 140.75 108.05) - (end 140.7 108) + (start 129.3 111.65) + (end 129.5 111.65) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "6e5347de-4f1c-4c8b-a1e7-7f4885fa3339") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "58cea02a-f912-4a25-a3ae-8f491af13b0e") ) (segment - (start 135.4 106.2) - (end 134.75 106.2) + (start 122.7 110.8) + (end 128.45 110.8) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "7a3bcf1f-8bfc-487f-a371-212f7757face") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "592d6ec8-d3fb-4b54-8adb-95703b8075d2") ) (segment - (start 134.75 106.2) - (end 134.65 106.1) + (start 120.4 97.900001) + (end 120.5 98.000001) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "7eaee3b7-f686-418d-b2f4-ff94c0250acc") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "5fea2c86-9efc-4b3e-98d6-105976c7a1ec") ) (segment - (start 140.8 108.05) - (end 140.75 108.05) + (start 122.7 84.725) + (end 122.7 85.856371) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "881cc768-968b-4d69-bd7b-1f646e2c9f66") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "7d93497f-56bd-4a38-9d34-d8236e04351b") ) (segment - (start 131.975 106.04) - (end 132.655 106.04) - (width 0.3) + (start 122.325 84.725) + (end 122.7 84.725) + (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "a7cff183-d23d-42db-b327-c884a29c1f7d") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "af80df4f-7dec-4f56-ae3d-e1467ac2a053") ) (segment - (start 142.5 110.55) - (end 142.5 110) + (start 121.1 83.5) + (end 122.325 84.725) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "bab5b367-8f3c-4163-8e79-7ab7520dd317") + (net "/Buttons_Direct/BTN_THR_DN") + (uuid "d68600ef-0fb2-42bf-809e-b99c5393361c") ) (segment - (start 143 108.2) - (end 140.95 108.2) + (start 128.479999 115.92) + (end 128.1 115.92) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "bc668708-456b-4da3-9207-779090886da5") + (net "/MCU_Core/USB_DP_MCU") + (uuid "736da687-a4f1-424e-8c82-16b241d97753") ) (segment - (start 133.8 106.1) - (end 133.5 106.4) + (start 128.8 113.35) + (end 128.8 115.6) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "cb0197fc-53dc-4a57-b8a7-ee3058fc3119") + (net "/MCU_Core/USB_DP_MCU") + (uuid "c8461804-450c-4609-95d6-c620ded5c934") ) (segment - (start 142.5 110) - (end 143.4 109.1) + (start 129.5 113.35) + (end 128.8 113.35) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "cca48839-d098-4a8a-9e9e-fa5c978b9f0e") + (net "/MCU_Core/USB_DP_MCU") + (uuid "cb27d9ba-4aff-4698-8318-3f025d5bd300") ) (segment - (start 138.75 107.25) - (end 136.55 107.25) + (start 128.8 115.6) + (end 128.479999 115.92) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "d1409841-2974-4d04-bb07-54eaf179ec3f") + (net "/MCU_Core/USB_DP_MCU") + (uuid "fd16dec7-1763-4fe5-9970-6882957b1ba8") ) (segment - (start 143.4 109.1) - (end 143.4 109.05) + (start 121.775 127.9) + (end 121.775 127) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "d6a3a16e-c39a-44f8-bbec-0a7d579ccede") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "0f84ee66-9505-4ec6-be94-5c4df95eff64") ) (segment - (start 142.45 110.65) - (end 142.45 110.6) + (start 124.225 125.345) + (end 124.08 125.2) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "d7f39b0c-ea17-4ee1-bae8-abe7547062f1") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "170ff2d8-02f4-41e1-a100-65488a8c9bc4") ) (segment - (start 140.5 107.95) - (end 139.45 107.95) + (start 124.4 120.265685) + (end 124.4 120.4) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "d95da6ae-c7ed-4e7e-977f-d000736564eb") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "1be713cd-b6e7-41d6-b57b-3246fffba7f1") ) (segment - (start 140.7 108) - (end 140.55 108) + (start 124.4 120.4) + (end 126.2 122.2) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "dd18b50b-78a3-4f44-a696-eb3bf9c5483a") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "1ca45775-e7d3-4dea-9490-004c13b0c539") ) (segment - (start 135.55 106.3) - (end 135.5 106.25) + (start 123.925 128.2) + (end 122.075 128.2) (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "f8c11529-3727-46ec-a5f7-934ab727763f") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "2700ef26-6c68-4a7a-9957-529781cfd207") ) (segment - (start 132.655 106.04) - (end 132.655 106.15) - (width 0.3) + (start 124.48 124.42) + (end 124.48 124.8) + (width 0.2) (layer "F.Cu") - (net "/Power_Buck/BUCK_FB") - (uuid "ffaedb86-014e-491e-afcc-31d6d2d74461") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "2b366e32-5de9-440b-9d9f-cc78bff68768") ) (segment - (start 146.1792 84.3947) - (end 145.8047 84.7692) + (start 124.2 120.065686) + (end 124.4 120.265685) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "06201356-e9f2-4e56-a073-b0c351c95285") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "474b3670-d224-42eb-b4b3-98e44f3fdd4d") ) (segment - (start 146.5094 84.725) - (end 147.3 84.725) + (start 124.225 127) + (end 124.225 127.9) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "0ef3fe55-f3e9-4068-8870-ab6649e5a4bd") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "4cefa06b-c9bc-4d42-b67c-43b616b3d69c") ) (segment - (start 146.0926 83.1579) - (end 146.0926 84.3082) + (start 121.056239 126.281239) + (end 121.775 127) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "16e87141-9a5e-4bb8-8117-8a3607b99dbe") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "5643c4f0-c0a8-4855-8c6a-548a6af6cdc1") ) (segment - (start 146.0926 84.3082) - (end 146.1792 84.3947) + (start 124.8 123.6) + (end 124.8 124.1) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "227db2c9-c0a5-4bf3-92bc-7be35676bbc4") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "5b26e00d-7521-44da-b456-05194066fd96") ) (segment - (start 147.3 82.275) - (end 146.9755 82.275) + (start 124 119.6) + (end 124.2 119.8) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "6dc0deef-e181-4321-aa61-2b62298b0b4c") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "69453bc7-ee26-40ab-946f-062d025e30ad") ) (segment - (start 146.9755 82.275) - (end 146.0926 83.1579) + (start 124.225 127.9) + (end 123.925 128.2) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "835a0bb7-f187-44f4-b7c0-5398f82c64c8") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "7ccd4374-4cab-4de0-8057-91c0bdf95662") ) (segment - (start 146.1792 84.3947) - (end 146.5094 84.725) + (start 122.075 128.2) + (end 121.775 127.9) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "ad73a560-7fa6-4ca3-a188-2bdbc81fb09f") - ) - (via - (at 145.8047 84.7692) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "efcdf05f-1697-4c62-9981-94f3c1767e8b") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "7fee0d70-99af-4beb-aae6-b22a0205e1be") ) (segment - (start 140.0131 88.7501) - (end 143.9081 88.7501) + (start 126.2 122.2) + (end 124.8 123.6) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "1b0851b7-c38f-4a7f-b7a1-213dea67703f") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "abaddc09-e702-4c81-9c23-fa0303432973") ) (segment - (start 138.2486 90.8289) - (end 139.6991 89.3784) + (start 120.6 125.765642) + (end 121.056239 126.221881) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "1b6ec60d-1c3f-4a3b-a6f6-02e5039c54f5") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "b9712568-9e17-4c73-948b-8f218d406ec7") ) (segment - (start 146.5825 85.547) - (end 145.8047 84.7692) + (start 124.225 127) + (end 124.225 125.345) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "481acdab-3062-4855-b42a-25022662f52f") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "bc5be0f8-813c-415e-a243-eb81baccbc3c") ) (segment - (start 146.5825 86.0757) - (end 146.5825 85.547) + (start 124.48 124.8) + (end 124.08 125.2) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "61039170-c41a-4056-ad1a-444e4f532e46") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "c7f921bb-c082-48f5-b37e-beb6a3da33c6") ) (segment - (start 138.525 93.5) - (end 138.2486 93.2236) + (start 124.8 124.1) + (end 124.48 124.42) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "657e3bd2-8646-432a-8836-53fe2868d1fe") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "c979d3bb-8b99-465c-9c28-c0ca3ab58792") ) (segment - (start 139.6991 89.3784) - (end 139.6991 89.0641) + (start 129.5 114.2) + (end 130.5 114.2) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "99e89f3b-c07e-4daf-806b-34b22d6159c2") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "df39e8a7-11fb-4525-9226-eabcdfaf55e4") ) (segment - (start 143.9081 88.7501) - (end 146.5825 86.0757) + (start 121.056239 126.221881) + (end 121.056239 126.281239) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "cd11bbdb-3c9e-4482-ba20-6f81b5577f26") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "ef0cbb4d-c2dd-4b38-b57f-6b308081480b") ) (segment - (start 139.6991 89.0641) - (end 140.0131 88.7501) + (start 124.2 119.8) + (end 124.2 120.065686) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "d7a47062-f1a9-4371-9343-76874dfab727") + (layer "F.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "fd08c5e1-0e31-4fc2-89ca-48ac56da318c") ) - (segment - (start 138.2486 93.2236) - (end 138.2486 90.8289) - (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_DN") - (uuid "edf76088-efc1-40c3-a442-202409d0cd19") + (via + (at 120.6 125.765642) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "120a3a2b-44d4-43dc-be6c-d271c7e28e3f") ) - (segment - (start 135.75 123.105) - (end 135.75 121.5009) - (width 0.2) - (layer "F.Cu") - (net "/USB_C/USB_CC1") - (uuid "c5491836-c463-46b6-89f1-87735bb13c8e") + (via + (at 130.5 114.2) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "9143ece4-31d3-4d3c-b021-cb2cf53a3e6f") ) (via - (at 135.75 121.5009) + (at 124 119.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "1a92415a-364f-4a93-a098-e4d54afc2065") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "d871a937-3974-4402-be7d-68a26a5c7908") ) (segment - (start 133.9993 121.5024) - (end 134.4009 121.1008) + (start 125.31125 92.514999) + (end 125.31125 92.715) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "0346e838-c262-4e8b-ba47-4e62776359c0") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "0b2774f7-27d8-4347-accb-fb341e7926dd") ) (segment - (start 130.265 123.815) - (end 132.5775 121.5025) + (start 120.6 125.765642) + (end 120.6 125.309403) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "b71910aa-3711-43a2-b7eb-c6a6de9a8c67") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "38d9a00a-f14f-4ee4-8349-6f149ded5dfe") ) (segment - (start 133.9993 121.5025) - (end 133.9993 121.5024) + (start 124.2 119.8) + (end 124.9 119.8) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "c78c8758-ac45-4799-89fa-1d7cf2358ede") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "42044632-9840-417a-b751-b997784c1eb8") ) (segment - (start 135.3499 121.1008) - (end 135.75 121.5009) + (start 124 119.6) + (end 124.2 119.8) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "df07f4e3-c89c-4446-9270-c3c860451fda") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "4d26661a-6e29-4f10-84d7-29d02a5f093a") ) (segment - (start 132.5775 121.5025) - (end 133.9993 121.5025) + (start 120.5 125.209403) + (end 120.5 95.090256) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "fb5cfff2-fcf4-440c-b072-635c91099215") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "8f0bc79a-019f-42af-b9f1-4b3b8668d221") ) (segment - (start 134.4009 121.1008) - (end 135.3499 121.1008) + (start 126.35125 93.775) + (end 126.36125 93.764999) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC1") - (uuid "fc6f7f58-a7f8-4c16-a7ca-a91831e5bd10") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "9aae3062-9025-4b19-9dbc-8fcd6d42d9ae") ) (segment - (start 136.75 123.9355) - (end 136.9987 124.1842) + (start 120.6 125.309403) + (end 120.5 125.209403) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "070d7f40-1486-4d27-862a-868a92b09af0") + (layer "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "bcbe05e7-67da-4378-b730-d654ed671b2d") ) (segment - (start 136.7983 124.3846) - (end 136.7983 126.0768) + (start 121.825257 93.764999) + (end 126.36125 93.764999) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "36cf638a-6674-4358-a43e-26a4cfb8f0ab") + (layer "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "bd45f50d-4fc6-4da6-a414-09b730ef1c0c") ) (segment - (start 143.4669 119.6739) - (end 148.0722 115.0686) + (start 125.31125 92.715) + (end 126.36125 93.764999) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "560e5e01-61d4-4344-b7dc-6c9d675a1970") + (layer "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "ea2a6cc5-a96d-4a26-aea3-62f403e4017a") ) (segment - (start 137.4463 124.1842) - (end 136.9987 124.1842) + (start 124.9 119.8) + (end 130.5 114.2) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "60c27134-a9fa-4b26-99a2-2465ee0782a1") + (layer "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "ed4422d7-347f-4109-a777-832df90df9eb") + ) + (segment + (start 120.5 95.090256) + (end 121.825257 93.764999) + (width 0.2) + (layer "B.Cu") + (net "/MCU_Core/PWR_BTN_SENSE") + (uuid "ef0bf4ae-5e19-41f3-9510-0cb90605fd86") ) (segment - (start 148.0722 115.0686) - (end 148.0722 111.8425) + (start 121.2 88.9) + (end 122.3 87.8) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "63f479d1-d314-436d-af09-088afd033244") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "12bee74a-787e-442c-91fb-6ebe577f4a87") ) (segment - (start 137.75 123.8805) - (end 137.4463 124.1842) + (start 121.3 97.66863) + (end 121.2 97.568629) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "71d3b192-1839-4a23-bb98-52639c2d1c00") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "2976c7d7-019a-4002-87ff-bdb900519b55") ) (segment - (start 136.75 123.105) - (end 136.75 123.9355) + (start 121.3 105.640927) + (end 121.3 97.66863) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "7476636b-5e03-4734-a955-824aa517bbe5") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "4bfd61cc-06de-4ef4-b42e-6579823e4fe9") ) (segment - (start 140.3811 126.7162) - (end 143.4669 123.6304) + (start 131.699999 115.1) + (end 130.9 115.9) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "947d5af1-74ea-4fe2-9313-5ddc50514be9") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "51b1304d-1369-460f-9359-0056c9a169cd") ) (segment - (start 137.4377 126.7162) - (end 140.3811 126.7162) + (start 124.5 67.8) + (end 129.6 62.7) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "c9e68bd2-a779-4e2f-af0e-178320381f2e") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "608d0971-87a4-4c41-9171-cd5456f0155d") ) (segment - (start 143.4669 123.6304) - (end 143.4669 119.6739) + (start 121.2 97.568629) + (end 121.2 88.9) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "ce755b20-8384-471c-bb45-e0c7adb23b73") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "953258b1-b3c3-4310-bca8-226e5ee3d13b") ) (segment - (start 136.9987 124.1842) - (end 136.7983 124.3846) + (start 121.8939 106.234827) + (end 121.3 105.640927) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "e0eb75b1-31f0-457a-842b-618055bb65b8") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "aaa36681-5ed9-4b4a-b03b-af541121b64f") ) (segment - (start 137.75 123.105) - (end 137.75 123.8805) + (start 129.6 62.7) + (end 131 62.7) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "e4c08c80-bec7-446f-8345-4c95e97a8f19") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "b5691e63-c817-41fb-8ed1-48fecc73c946") ) (segment - (start 136.7983 126.0768) - (end 137.4377 126.7162) + (start 130.9 115.9) + (end 129.5 115.9) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/USB_DP") - (uuid "ee9e4a7a-0a6f-4e7a-bf53-7b22bc15697f") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "c173b236-8e75-479f-b764-3741ec70f7b4") ) (via - (at 148.0722 111.8425) + (at 131 62.7) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/USB_DP") - (uuid "1a91819b-a86a-42c2-9ac3-3b63c5b53686") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "4f6adcd7-55c5-4b8c-8dc4-1bfb367e38ad") ) (via - (at 139.4846 96.5017) + (at 122.3 87.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/USB_DP") - (uuid "89857f18-3a06-4394-bfb3-ba1ebe366012") - ) - (segment - (start 139.4846 96.5017) - (end 138.8829 95.9) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/USB_DP") - (uuid "566dac3e-e131-4cad-849a-0de9bdd467c5") - ) - (segment - (start 138.8829 95.9) - (end 138.525 95.9) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/USB_DP") - (uuid "77f47d03-d8bb-40e6-b53a-2d48f1848fbc") - ) - (segment - (start 148.4125 111.5022) - (end 148.4125 99.9499) - (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/USB_DP") - (uuid "2eb99498-22a9-4872-aa92-45f90a8512b1") - ) - (segment - (start 148.0722 111.8425) - (end 148.4125 111.5022) - (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/USB_DP") - (uuid "61bfef53-31b3-431e-8499-5d2c7575201d") - ) - (segment - (start 145.9059 97.4433) - (end 140.4262 97.4433) - (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/USB_DP") - (uuid "82cfed0d-280b-4de4-a461-13f20f91cd9c") - ) - (segment - (start 148.4125 99.9499) - (end 145.9059 97.4433) - (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/USB_DP") - (uuid "8e8bd210-17b2-48f6-b3a0-6207c47054a8") - ) - (segment - (start 140.4262 97.4433) - (end 139.4846 96.5017) - (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/USB_DP") - (uuid "b204b1a1-c291-45ee-acd7-4304302bb564") - ) - (segment - (start 136.9775 122.0573) - (end 137.4527 121.5821) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "340dbe31-5c4b-4061-8a4f-a5bc24233e24") - ) - (segment - (start 137.9017 101.2861) - (end 137.9017 95.2416) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "5bf7aa95-9eec-4103-8788-bb467c226d7d") - ) - (segment - (start 136.9775 122.0573) - (end 136.4571 122.0573) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "627412db-ab07-4333-93af-8d1e87f4e4a4") - ) - (segment - (start 137.4527 120.4683) - (end 143.8796 114.0414) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "70a731a7-517e-4874-9f37-721f4a9c3f59") - ) - (segment - (start 141.1998 104.5842) - (end 137.9017 101.2861) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "7b914cef-3b8e-47f1-a16e-7cb26f29b2fc") - ) - (segment - (start 141.1998 105.7306) - (end 141.1998 104.5842) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "9a315206-bcb5-410a-8b2e-921e01fb82eb") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "bdef07ff-ad28-45a4-b222-b9b740e0a088") ) - (segment - (start 136.4571 122.0573) - (end 136.25 122.2644) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "9bef793e-73b9-4a6b-af3e-daaafdd184b5") + (via + (at 131.7 115.1) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "c5650d54-1694-434e-b85f-bfb7fa538ef6") ) - (segment - (start 143.8796 108.4104) - (end 141.1998 105.7306) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "c5923b48-5d2c-4339-baab-69b63592af1f") + (via + (at 124.5 67.8) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "cccd5191-3b80-4756-9d28-b00adf544a5f") ) - (segment - (start 137.25 122.3298) - (end 136.9775 122.0573) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "cd2961b1-97c5-410f-9585-e8a904909e09") + (via + (at 121.8939 106.234827) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "f78afbaf-f545-4ff6-acd0-6b326aae70c7") ) (segment - (start 137.25 123.105) - (end 137.25 122.3298) + (start 131.7 113.8) + (end 131.7 115.1) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "cdd5d2c3-d2f5-49f4-897f-4292cdd7008c") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "0c0df5a5-eff8-4acd-a13f-544f600e152b") ) (segment - (start 143.8796 114.0414) - (end 143.8796 108.4104) + (start 136.225 62.7) + (end 136.225 61.8) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "e750de88-a9b7-43ca-a737-b7c16ca7d645") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "12c6edbc-4935-4715-84a2-277a879d1ecf") ) (segment - (start 137.4527 121.5821) - (end 137.4527 120.4683) + (start 121.8939 106.234827) + (end 122.642 106.982927) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "ee82a2ef-71b2-434e-abba-705b766e4830") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "4c375750-3089-4cb4-bb65-28c238f8bb5f") ) (segment - (start 136.25 122.2644) - (end 136.25 123.105) + (start 122.3 87.8) + (end 122.8 87.3) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/USB_DM") - (uuid "f80437cf-d976-4e6d-9876-d354f230369e") - ) - (via - (at 137.9017 95.2416) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/MCU_Core/USB_DM") - (uuid "86b10c37-e78a-4295-bd8d-a9bf4ecdada9") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "6e1af58d-042c-429b-aae5-9136236c76c5") ) (segment - (start 138.525 94.7) - (end 137.9834 95.2416) + (start 133.775 61.8) + (end 133.775 62.7) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/USB_DM") - (uuid "8cdd24e3-fa99-4dd0-bc71-ce454d0ce8af") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "96667236-8c7e-4060-9898-baa88821139f") ) (segment - (start 137.9834 95.2416) - (end 137.9017 95.2416) + (start 134.375 61.2) + (end 133.775 61.8) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/USB_DM") - (uuid "e5e29f1c-df1c-4b47-97e9-b36e0198f91a") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "976cbf8a-3604-4be9-a599-ae82885ab507") ) (segment - (start 138.75 123.105) - (end 138.75 126.065) + (start 122.8 69.5) + (end 124.5 67.8) (width 0.2) - (layer "F.Cu") - (net "/USB_C/USB_CC2") - (uuid "90598b2d-633d-4e72-9cdc-ab017cd54063") - ) - (via - (at 138.75 126.065) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/USB_C/USB_CC2") - (uuid "c495dbd1-8897-4054-8ca1-51290846c47e") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "b7a8d07e-8092-410d-b6fb-186a51f20730") ) (segment - (start 141.265 126.065) - (end 138.75 126.065) + (start 136.225 61.8) + (end 135.625 61.2) (width 0.2) (layer "B.Cu") - (net "/USB_C/USB_CC2") - (uuid "116ae705-061a-4bf1-9c7f-889839cec620") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "c3e88980-216e-4d6d-aa80-e1a14e044226") ) (segment - (start 132.3852 78.0739) - (end 132.3852 76.7368) + (start 131 62.7) + (end 133.78 62.7) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "13b006d4-91a3-4755-920e-eb97abb022f1") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "dfe13138-ed13-4f4e-a0ad-6e9f0c1c1d76") ) (segment - (start 130.2688 90.6305) - (end 130.2688 80.1903) + (start 122.8 87.3) + (end 122.8 69.496948) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "145e616f-b22a-408a-a278-205feacc9e80") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "e4a57be4-6bca-4c8a-a0f2-28843d475d63") ) (segment - (start 130.2688 80.1903) - (end 132.3852 78.0739) + (start 124.882927 106.982927) + (end 131.7 113.8) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "272eaa57-a033-4ffb-9ec8-555d2e485edf") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "ed6350cf-b6b1-4267-86bc-4be0c829cc36") ) (segment - (start 127.2227 93.6766) - (end 130.2688 90.6305) + (start 135.625 61.2) + (end 134.375 61.2) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "70135938-4eeb-45bd-8d2b-fa4bdc5776ed") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "fe3f5c5b-1d8c-405b-99e6-a1d7a1daa275") ) (segment - (start 126.6701 93.6766) - (end 127.2227 93.6766) + (start 122.642 106.982927) + (end 124.882927 106.982927) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "9ca5ba52-2cd3-4660-ad72-5bcdea06cd32") + (layer "B.Cu") + (net "/Buttons_Direct/BTN_TRIG_DIG") + (uuid "fe4acf2c-181b-4dec-923a-6fd6e791a61f") ) (segment - (start 135 74.122) - (end 135 69.77) + (start 127.8 117.8) + (end 129.3 117.8) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "d50121f2-0073-4bb3-8d98-329558bdc72d") + (net "/XBee/XBEE_CTS") + (uuid "1b1ab796-f613-4eee-8bb4-0d2a50887056") ) (segment - (start 132.3852 76.7368) - (end 135 74.122) + (start 129.3 117.8) + (end 129.5 117.6) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_X") - (uuid "f0375fe4-15c4-493e-9065-fab9eaeaf7ae") + (net "/XBee/XBEE_CTS") + (uuid "66d5793a-97c1-4869-bfb0-8dcb320e37cf") ) (via - (at 126.6701 93.6766) + (at 127.8 117.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/STICK_X") - (uuid "e0459802-834e-49e7-8ad7-4b21a18bebd0") - ) - (segment - (start 126.9733 93.9798) - (end 126.6701 93.6766) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STICK_X") - (uuid "871454fa-bfcf-4fba-9c6b-0ee93ca721ff") + (net "/XBee/XBEE_CTS") + (uuid "38490006-ab15-4ec9-ae52-51accf4cab6a") ) (segment - (start 127.9 97.1) - (end 126.9733 97.1) + (start 126.45 121.3) + (end 126.45 119.15) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STICK_X") - (uuid "d0957660-05d1-438a-bc54-347e5037773a") + (net "/XBee/XBEE_CTS") + (uuid "5c6a1e5b-d637-4462-89bf-65e0cdffa25b") ) (segment - (start 126.9733 97.1) - (end 126.9733 93.9798) + (start 126.45 119.15) + (end 127.8 117.8) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/STICK_X") - (uuid "d96f2c92-9f7c-4b6e-a80b-7275246f48a4") - ) - (segment - (start 132.4711 90.8956) - (end 132.4711 92.1085) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "16ca908c-4a58-41a0-aaf5-751285f6e427") + (net "/XBee/XBEE_CTS") + (uuid "92d59d70-dfb1-460d-97aa-1bb683ff6634") ) (segment - (start 143.73 78.5) - (end 141.9106 78.5) + (start 126.862537 122.48) + (end 126.002198 123.340339) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "17bb9ed4-9aa6-46de-b958-64ec6f09a69c") - ) - (segment - (start 141.9106 78.5) - (end 136.7686 83.642) - (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "214abeee-24c4-48fa-9208-6b15424b511f") + (net "/MCU_Core/RGB_DIN") + (uuid "069d4c83-418d-49de-815b-787d8ecd63c6") ) (segment - (start 130.0577 95.46) - (end 130.2073 95.6096) + (start 127.9 122.48) + (end 126.862537 122.48) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "4a97cdef-d9da-449e-9dba-6c9d80020525") + (net "/MCU_Core/RGB_DIN") + (uuid "341740ff-cc73-4f3a-b909-be2118756c34") ) (segment - (start 130.0577 94.5219) - (end 130.0577 95.46) + (start 130.4 117.9) + (end 129.85 118.45) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "5526c1ec-8343-4028-acf5-dd79481ad4c0") + (net "/MCU_Core/RGB_DIN") + (uuid "4335f5e3-1db9-4276-a06f-3db8c3a4d344") ) (segment - (start 132.4711 92.1085) - (end 130.0577 94.5219) + (start 129.5 118.45) + (end 129.3 118.45) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "b3a02a89-d27b-44db-aa3b-469505f13cfe") + (net "/MCU_Core/RGB_DIN") + (uuid "b859599c-972f-467d-95bf-fae6f2760578") ) (segment - (start 136.7686 83.642) - (end 136.7686 86.5981) + (start 130.4 117.4) + (end 130.4 117.9) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "b5ad3314-e659-43ed-bcb9-19651e22e8db") + (net "/MCU_Core/RGB_DIN") + (uuid "de86b0ca-41f1-4ef0-a595-fc8d3367a1fe") ) (segment - (start 136.7686 86.5981) - (end 132.4711 90.8956) + (start 129.85 118.45) + (end 129.5 118.45) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "f9f027dc-755a-47a2-907d-11aced51315f") + (net "/MCU_Core/RGB_DIN") + (uuid "e40808fe-7a20-433e-89d0-90f746c7e8e2") ) (via - (at 130.2073 95.6096) + (at 126.002198 123.340339) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "962f45d1-aa09-48de-b73d-4948d361d99a") - ) - (segment - (start 128.2904 95.6096) - (end 130.2073 95.6096) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "33b57861-e39e-479f-9b59-1bef51fdb9f0") - ) - (segment - (start 127.9 96) - (end 128.2904 95.6096) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/STICK_Y") - (uuid "c6c4f43b-557c-49ca-b4bd-b0d2675916d6") + (net "/MCU_Core/RGB_DIN") + (uuid "9e61c00f-e310-44f6-ae50-f5d022f87cc2") ) (via - (at 142.9997 92.3859) + (at 130.4 117.4) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "bd20417c-ad82-4593-ac2f-67cdfbdb5809") + (net "/MCU_Core/RGB_DIN") + (uuid "c723a61a-6ce8-45d4-829d-cee0cc07283e") ) (segment - (start 144.3818 93.7397) - (end 145.7404 95.0983) - (width 0.4) + (start 126.651471 124.1) + (end 127.148529 124.1) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "0432f97a-a2cf-4053-a056-f096459c78ad") + (net "/MCU_Core/RGB_DIN") + (uuid "01789416-65dd-4905-a80c-626137ce2070") ) (segment - (start 142.9997 92.3859) - (end 142.9997 92.0747) - (width 0.4) + (start 126.002198 123.340339) + (end 126.002198 123.450727) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "0d4d8093-bdb3-4a96-b1d6-675a674554fe") + (net "/MCU_Core/RGB_DIN") + (uuid "220b94dc-39ef-49ab-a4e1-bbc5dc3466b7") ) (segment - (start 145.7776 95.0983) - (end 146.1688 95.4895) - (width 0.4) + (start 127.84 119.65) + (end 130.09 117.4) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "0fbd5e3c-cdef-4165-895b-534bae998d4c") + (net "/MCU_Core/RGB_DIN") + (uuid "2ac4073e-65ba-41a3-9b5a-28a90b9fd315") ) (segment - (start 146.1688 95.4895) - (end 146.1688 96.5381) - (width 0.4) + (start 130.09 117.4) + (end 130.4 117.4) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "14399ee5-8c0b-4995-ab48-9fed091a3a85") + (net "/MCU_Core/RGB_DIN") + (uuid "7499b5d5-2f12-4514-8f5c-04d98eaf9dfd") ) (segment - (start 142.737 93.7397) - (end 142.9997 93.7397) - (width 0.4) + (start 127.148529 124.1) + (end 127.84 123.408529) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "168c862e-b1a1-4737-9ba1-ca3f4bb490c4") + (net "/MCU_Core/RGB_DIN") + (uuid "b7ee7b59-7fe6-4288-8815-08df183b1a77") ) (segment - (start 146.1688 96.5438) - (end 146.1688 96.5381) - (width 0.4) + (start 127.84 123.408529) + (end 127.84 119.65) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "1d41a054-1f9f-420e-9297-63594fcd1e60") + (net "/MCU_Core/RGB_DIN") + (uuid "bfba3b82-57a2-41c3-a4b0-05d38c9025de") ) (segment - (start 146.495 96.87) - (end 146.1688 96.5438) - (width 0.4) + (start 126.002198 123.450727) + (end 126.651471 124.1) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "1f79f772-f160-4e90-be99-7db8362421b2") + (net "/MCU_Core/RGB_DIN") + (uuid "e5b1a5eb-7103-4ccc-96c9-e431cbbd041f") ) (segment - (start 142.3 91.375) - (end 140.6125 91.375) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "34cf6699-e520-490c-8f99-e9c8dbbda187") + (start 130.389999 120.689999) + (end 130.55 120.529998) + (width 0.2) + (layer "F.Cu") + (net "/XBee/XBEE_DIN") + (uuid "094527bc-aa9c-4730-b3f2-972f660b4b69") ) (segment - (start 127.4956 64.6) - (end 126.4844 65.6112) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "378d55f2-608c-417d-a43e-42bfdd90dce1") + (start 130.179998 120.689999) + (end 130.389999 120.689999) + (width 0.2) + (layer "F.Cu") + (net "/XBee/XBEE_DIN") + (uuid "2dbce990-aa41-44ee-923d-ec3f6cc21f4b") ) (segment - (start 127.3642 67.95) - (end 127.625 67.95) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "48a1852c-e34a-4383-8a31-327cda3cada2") + (start 130.55 120.529998) + (end 130.55 119.5) + (width 0.2) + (layer "F.Cu") + (net "/XBee/XBEE_DIN") + (uuid "8de7eea9-e12c-4d94-bb36-9c3f7cafd606") ) - (segment - (start 142.9997 92.3859) - (end 142.9997 93.7397) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "4bd31057-28bd-43d8-9907-8ec8d8713e4e") + (via + (at 130.179998 120.689999) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_DIN") + (uuid "c00ec563-6831-4b9c-9c1d-aeb42885665d") ) (segment - (start 142.9997 92.0747) - (end 142.3 91.375) - (width 0.4) + (start 130.179998 120.689999) + (end 129.969997 120.9) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "550b5e80-c138-445b-9273-1dfd0a2828d5") + (net "/XBee/XBEE_DIN") + (uuid "7f77add9-deb8-4c73-8120-aa2e94a923f2") ) (segment - (start 145.7404 95.0983) - (end 145.7776 95.0983) - (width 0.4) + (start 129.39 120.9) + (end 128.99 121.3) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "56c9872d-a102-46f2-8aa2-238160e34f78") + (net "/XBee/XBEE_DIN") + (uuid "aea3f8a9-1f3e-480c-830d-72fe4304e721") ) (segment - (start 145.1081 96.5381) - (end 144.555 95.985) - (width 0.4) + (start 129.969997 120.9) + (end 129.39 120.9) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "610092f0-0e29-4a2f-b9c4-f52481ad2eab") + (net "/XBee/XBEE_DIN") + (uuid "c8f1e799-62f6-4e9f-840e-907d0d21c1f0") ) (segment - (start 142.0586 93.8) - (end 142.6767 93.8) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "6d37eba2-e7df-433f-a372-698a9df5c3e4") + (start 131.4 119.5) + (end 131.4 118.750454) + (width 0.2) + (layer "F.Cu") + (net "/XBee/XBEE_DOUT") + (uuid "51d3dbfe-868d-4d0c-af0b-7f4c70e091a0") ) (segment - (start 132.5 69.77) - (end 129.445 69.77) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "6edd152e-c1f8-4f4b-9c2d-5171edf1afb7") + (start 131.4 118.750454) + (end 131.615136 118.535318) + (width 0.2) + (layer "F.Cu") + (net "/XBee/XBEE_DOUT") + (uuid "61cc0bc5-3f32-4df1-beb7-ea8a14460f80") ) - (segment - (start 145.505 76.685) - (end 144.415 76.685) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "744d28c7-b1fb-42a5-a260-4ff67cfb657b") + (via + (at 131.615136 118.535318) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_DOUT") + (uuid "9427dd84-6349-49de-982a-1921a860e4ca") ) (segment - (start 140.025 95.9) - (end 139.3144 95.1894) - (width 0.4) + (start 131.615136 118.535318) + (end 131.53 118.620454) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "76a017d2-bb1d-450d-a53e-2908ad5ee81b") + (net "/XBee/XBEE_DOUT") + (uuid "700ce4ce-b6b9-4d17-8006-13325572c88d") ) (segment - (start 139.3144 92.6731) - (end 140.6125 91.375) - (width 0.4) + (start 131.53 118.620454) + (end 131.53 121.3) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "76c892c7-cb8a-4e75-a9c1-849eecfb1093") + (net "/XBee/XBEE_DOUT") + (uuid "d279c5ae-73d7-4c43-ac9c-54d97224e2f4") ) (segment - (start 142.9997 93.7397) - (end 144.3818 93.7397) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "8333e08c-aef6-4320-b9fa-9448c291567d") + (start 133.451471 116.9) + (end 132.25 118.101471) + (width 0.2) + (layer "F.Cu") + (net "ACCEL_INT1") + (uuid "37c71620-b456-46d1-a71f-b89d9e3a7362") ) (segment - (start 142.6767 93.8) - (end 142.737 93.7397) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "8337947a-be03-459d-8b06-e99fef4d146c") + (start 139.4 116.9) + (end 133.451471 116.9) + (width 0.2) + (layer "F.Cu") + (net "ACCEL_INT1") + (uuid "96dd415c-e701-4640-a1ea-f4858bf91b68") ) (segment - (start 146.1688 96.5381) - (end 145.1081 96.5381) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "876e9a57-9e1e-4655-bef9-27d7c707eee2") + (start 132.25 118.101471) + (end 132.25 119.5) + (width 0.2) + (layer "F.Cu") + (net "ACCEL_INT1") + (uuid "df0dc5e0-62a0-4ada-be8d-8a8596c11090") ) - (segment - (start 126.4844 67.0702) - (end 127.3642 67.95) - (width 0.4) - (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "a075dc70-94dd-4bee-8154-62dac744eb32") + (via + (at 139.4 116.9) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "ACCEL_INT1") + (uuid "ac8bf407-7ec1-4446-be39-1365123b06f5") ) (segment - (start 142.0586 93.8) - (end 141.65 93.8) - (width 0.4) + (start 134.062893 126.77) + (end 136.48 126.77) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "ba9ba568-c0c2-4c6c-a03b-62f1bb549713") + (net "ACCEL_INT1") + (uuid "17655b0a-5d6a-4dcb-adab-3e06b0920eaf") ) (segment - (start 126.4844 65.6112) - (end 126.4844 67.0702) - (width 0.4) + (start 130.5625 126.1) + (end 133.392894 126.1) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "c33920a9-cf1f-4673-b521-485d1c73d14a") + (net "ACCEL_INT1") + (uuid "1ad5f793-9d9f-4e94-b04b-5b7bb7167373") ) (segment - (start 128.32 64.6) - (end 127.4956 64.6) - (width 0.4) + (start 136.48 126.77) + (end 140.351471 122.898529) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "c89270e9-2efb-45cf-94ca-80febe15f3e7") + (net "ACCEL_INT1") + (uuid "80a330f3-0a02-4259-b549-9b6eb7b3ae15") ) (segment - (start 129.445 69.77) - (end 127.625 67.95) - (width 0.4) + (start 140.351471 119.3) + (end 139.4 118.348529) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "e11e2dbd-5e1c-4369-a999-c272a6bee6e6") + (net "ACCEL_INT1") + (uuid "a19370fb-4d60-4ae3-b24f-f4d7754a4fd8") ) (segment - (start 139.3144 95.1894) - (end 139.3144 92.6731) - (width 0.4) + (start 139.4 118.348529) + (end 139.4 116.9) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "e83d6604-773e-4236-a935-cd99774cc3a9") + (net "ACCEL_INT1") + (uuid "b5018752-fbda-42cc-849a-1bf72962cdd6") ) (segment - (start 144.415 76.685) - (end 143.73 76) - (width 0.4) + (start 130.5625 126.1) + (end 130.5625 125.9375) + (width 0.2) (layer "B.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "f2a46070-cc12-48cd-937e-68ee42061e2b") - ) - (segment - (start 143.73 76) - (end 145.1567 77.4267) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "2e58bbba-e780-4f3d-a6de-7e63ce06b6e9") - ) - (segment - (start 145.1567 77.4267) - (end 145.1567 83.964) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "37a6c66f-d265-44a2-87c8-4a482d99a5e5") - ) - (segment - (start 145.103 84.0177) - (end 145.103 90.2826) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "3dbeea84-1442-44f2-bcbf-574d06cf69a4") - ) - (segment - (start 138.73 76) - (end 143.73 76) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "4768f334-3d7f-43a9-87bd-0e7fef53b6cf") - ) - (segment - (start 145.1567 83.964) - (end 145.103 84.0177) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "a088a4bb-eb01-40d6-bf62-898f830dac1e") + (net "ACCEL_INT1") + (uuid "d6880b8a-030c-49de-9f17-07f69ae0eaf7") ) (segment - (start 132.5 69.77) - (end 138.73 76) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "a2acf524-62ee-44b8-880c-2f2927911fa3") + (start 133.392894 126.1) + (end 134.062893 126.77) + (width 0.2) + (layer "B.Cu") + (net "ACCEL_INT1") + (uuid "da0c4dd7-357b-440d-9c46-3da7a8e6c2e0") ) (segment - (start 145.103 90.2826) - (end 142.9997 92.3859) - (width 0.4) - (layer "In1.Cu") - (net "/MCU_Core/3V3_RF") - (uuid "ce9564ba-5807-4741-aefb-f36d87ac4513") - ) - (via - (at 134.7091 92.7872) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "71b4360a-c946-4bb0-94d3-b6d8b98ed3b7") + (start 140.351471 122.898529) + (end 140.351471 119.3) + (width 0.2) + (layer "B.Cu") + (net "ACCEL_INT1") + (uuid "ee1ae678-8157-4fd3-aa8c-4d9e25e73836") ) (segment - (start 134.025 93.5) - (end 134.7091 92.8159) + (start 130.5625 125.9375) + (end 130.6 125.9) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "506dd03a-03dd-4127-81a9-4bec6323d966") + (net "ACCEL_INT1") + (uuid "efd62668-5d5e-404a-b0a9-7cc97d99348d") ) (segment - (start 134.7091 92.8159) - (end 134.7091 92.7872) + (start 147.775 74.725) + (end 147.3 74.725) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "cdb00ac4-6171-4444-8c89-1fd4b4b420ba") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "0b1c249c-e165-4894-a80f-bf023fd197f9") ) (segment - (start 131.9971 84.25) - (end 131.75 84.25) + (start 147.867157 94.667157) + (end 146.1 92.9) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "57e2e62d-a576-42ef-8a10-dad74a16cf7f") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "157ea7ac-aaf2-4c87-ab2c-8b29a7573483") ) (segment - (start 134.7091 86.962) - (end 131.9971 84.25) + (start 133 118.2) + (end 133 119.4) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "652f5dff-1070-49cb-a077-171956f54282") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "235f79a8-6e5e-4a13-b9f5-50d8d9178938") ) (segment - (start 134.7091 92.7872) - (end 134.7091 86.962) + (start 146.1 84) + (end 145.4 83.3) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/BTN_STICK") - (uuid "c5ce953c-bc11-415f-a4b2-d0a4c19e2288") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "28834561-c913-40ee-86d5-05c962f62dc3") ) (segment - (start 123.3961 128.2123) - (end 122.5996 128.2123) + (start 149 73.5) + (end 147.775 74.725) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "477fd722-61b0-4ec3-91e6-b9062ef4fe6a") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "2efef516-6eff-4c34-865d-a8deac585e85") ) (segment - (start 120.6886 125.9136) - (end 120.6886 97.0701) + (start 147.3 72.275) + (end 147.775 72.275) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "607acc78-1f2b-4147-8e03-e84b47260402") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "4c414a89-f71b-43f1-80ba-75193e212593") ) (segment - (start 121.775 127) - (end 120.6886 125.9136) + (start 145.4 83.3) + (end 146.1 82.6) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "643a89bc-ee5a-4647-881d-44a1700929b1") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "554fb40a-413e-4d20-9a46-2f2b7ee2e997") ) (segment - (start 124.225 125.345) - (end 124.08 125.2) + (start 146.1 75.925) + (end 147.3 74.725) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "6ea783a8-0f57-4a9f-8dab-af8e64f5d641") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "56503a78-7f46-4a32-a8dc-809fe03db5f9") ) (segment - (start 124.225 127) - (end 124.225 125.345) + (start 146.1 82.6) + (end 146.1 75.925) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "7d1584cd-4a5d-4b7c-b899-f78a7c87a5e8") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "6e287b24-d30c-4889-8ea8-d9bf69409881") ) (segment - (start 124.225 127.3834) - (end 123.3961 128.2123) + (start 133 119.4) + (end 133.1 119.5) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "a305a082-2b55-40dd-9978-6e8271ccd044") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "77bad366-5245-426d-8c90-6169c61f654b") ) (segment - (start 122.5996 128.2123) - (end 122.1026 127.7153) + (start 147.034358 98.156239) + (end 147.867157 97.32344) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "c321837e-481d-47cc-8ea2-40711398ffeb") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "7b70c74a-1f0a-4f33-b219-a2e2a570d082") ) (segment - (start 122.1026 127.3276) - (end 121.775 127) + (start 146.1 92.9) + (end 146.1 84) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "c534d199-4f1d-43ec-a0a2-f6012ab31ef5") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "88b7f75d-c7f3-4dcd-84c7-c1b4791eb5ee") ) (segment - (start 124.225 127) - (end 124.225 127.3834) + (start 147.867157 97.32344) + (end 147.867157 94.667157) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "d323bb4b-faba-43b1-a575-60579c89e027") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "89e6bdde-a1be-4ceb-b415-2381ea262d6d") ) (segment - (start 122.1026 127.7153) - (end 122.1026 127.3276) + (start 147.775 72.275) + (end 149 73.5) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "f48fdb68-3d53-48b5-9f5d-28399001f98e") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "b7d560b7-2c3c-4cab-8bb9-d0dd44afce3f") ) (via - (at 145.4529 98.045) + (at 147.034358 98.156239) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "1d9d45b8-038c-4990-b1a1-6805433d454f") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "1d581a6b-f358-48a6-aa64-e7c6e0995879") ) (via - (at 120.6886 97.0701) + (at 133 118.2) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "c4aa3332-fc4d-4b3f-89f9-8ecac616c31e") - ) - (segment - (start 144.1077 96.6998) - (end 142.7545 96.6998) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "1266e41b-6edc-46b0-b275-6bcc3607923c") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "66057ffb-5d78-4d9c-895d-fd1425eb4e2a") ) (segment - (start 142.7545 96.6998) - (end 142.0547 96) + (start 147.034358 98.156239) + (end 147.034358 107.614171) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "3813067c-a88e-45cf-b83d-23970eefe039") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "08aa7e49-220c-4a23-95bf-cec61d7de312") ) (segment - (start 121.6501 97.0701) - (end 120.6886 97.0701) + (start 147.034358 107.614171) + (end 137.548529 117.1) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "3aa3b27e-467a-452e-ab3c-6e79164646cd") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "81623b06-7257-4919-a565-f1dabbfc03f6") ) (segment - (start 125.92 94.6) - (end 125.92 93.12375) + (start 134.1 117.1) + (end 133 118.2) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "3cb87e96-ccd3-442e-a395-5e476ca5d8bb") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "dd500b0e-4b88-4856-8b2e-79b3a57c02db") ) (segment - (start 125.3113 92.6147) - (end 125.3113 92.515) + (start 137.548529 117.1) + (end 134.1 117.1) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "3f624d54-e62b-4b1e-aa4d-a19dc9286b6b") + (net "/Buttons_Direct/BTN_VOL_UP") + (uuid "fc3084dd-c586-4ab7-b1c2-b4ae24cdbf6b") ) (segment - (start 122.0708 96.6494) - (end 121.6501 97.0701) + (start 133.95 118.25) + (end 133.9 118.2) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "59e3dd3d-9db5-4431-bf9d-477899d36bc5") + (layer "F.Cu") + (net "/XBee/XBEE_RTS") + (uuid "557ba30a-346c-4965-993a-92eac2fc53c5") ) (segment - (start 125.311 92.615) - (end 125.3113 92.6147) + (start 133.95 119.5) + (end 133.95 118.25) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "6091bc3c-b637-4280-9cb8-d25028d25e3a") + (layer "F.Cu") + (net "/XBee/XBEE_RTS") + (uuid "e9623e2d-d4f4-40a5-aac2-902b8b25e282") ) - (segment - (start 125.31125 92.514999) - (end 125.31125 92.715) - (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "696b8244-03a1-41ed-8d9a-8bfea3c82a37") + (via + (at 133.9 118.2) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_RTS") + (uuid "2c5c4e61-a679-4e76-b256-3a38d9d228a0") ) (segment - (start 145.4529 98.045) - (end 144.1077 96.6998) + (start 134.07 118.37) + (end 134.07 121.3) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "79b1a2ee-81fc-4b32-9aef-376f84f5ed2e") + (net "/XBee/XBEE_RTS") + (uuid "2e2e8a53-c2b2-49d7-85bd-1dbc80500567") ) (segment - (start 124.0438 93.975) - (end 122.0708 95.948) + (start 133.9 118.2) + (end 134.07 118.37) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "8cc24cc3-f501-4264-a8f2-b4acd9aee6a0") + (net "/XBee/XBEE_RTS") + (uuid "5345da18-b62d-4b69-897c-3b98de31a0b8") ) (segment - (start 142.0547 96) - (end 141.65 96) + (start 147.4 85.293629) + (end 147.4 85.956371) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "a3db2ce1-2cc4-4e32-95c7-c55bef7323b3") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "0c98d81f-ddf9-4aac-8c84-86a6def16eb8") ) (segment - (start 125.92 93.12375) - (end 125.31125 92.515) + (start 147.3 82.275) + (end 147.775 82.275) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "ac30b8ce-00f8-463a-875e-b78893bf89ed") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "1b64869b-4832-49ed-a543-46c29fdfa1eb") ) (segment - (start 122.0708 95.948) - (end 122.0708 96.6494) + (start 147.775 82.275) + (end 149 83.5) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "bcc8bf01-a698-4ffd-b6f2-8aeced68eb1a") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "27ddd182-dd00-42ca-8f0c-21fa9597bf60") ) (segment - (start 125.92 93.975) - (end 124.0438 93.975) + (start 134.7 117.7) + (end 134.7 119.4) (width 0.2) - (layer "B.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "d453d2f6-5c69-4ffe-b2d1-2d9467de4178") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "535879e3-9a23-49c2-a0b6-2873c92577e0") ) (segment - (start 144.0083 99.4896) - (end 145.4529 98.045) + (start 134.7 119.4) + (end 134.8 119.5) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "17f9ebe6-89da-4130-bda7-badc4255bae8") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "5c8c2057-8e4b-4cd1-ba11-b89d8e2d5cf3") ) (segment - (start 129.5625 102.6486) - (end 130.9998 102.6486) + (start 147.4 85.956371) + (end 147.868629 86.425) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "26218e70-c315-42f1-a6de-56fe0f05238b") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "60b7850a-96ce-4e53-a4e7-ed7b0d0e7270") ) (segment - (start 130.9998 102.6486) - (end 134.1588 99.4896) + (start 147.3 84.725) + (end 147.634315 85.059315) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "4f813731-a6ea-4098-95db-fc9850f094fc") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "656d6c5e-2368-4bd5-9b71-d6d330c7949a") ) (segment - (start 128.3301 101.4162) - (end 129.5625 102.6486) + (start 147.775 84.725) + (end 147.3 84.725) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "59a6a6da-e8b5-44a8-bed3-f273f01ffcc1") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "6c31d061-7a53-4a40-a01f-bba736812cc6") ) (segment - (start 125.0347 101.4162) - (end 128.3301 101.4162) + (start 148.4 97.9) + (end 147.7 98.6) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "6968c6cd-11cb-4c14-84f0-9909f12c6674") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "6cc66270-32cc-4aad-96a7-d9d5e139825c") ) (segment - (start 120.6886 97.0701) - (end 125.0347 101.4162) + (start 147.868629 86.425) + (end 148.4 86.425) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "88e3b7ce-1570-4478-9378-49d0145fb9b4") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "b94cc311-29a7-430b-be5d-0e7c08bafbe9") ) (segment - (start 134.1588 99.4896) - (end 144.0083 99.4896) + (start 147.634315 85.059315) + (end 147.4 85.293629) (width 0.2) - (layer "In1.Cu") - (net "/MCU_Core/PWR_BTN_SENSE") - (uuid "c4390c2c-d65b-46ee-bb9f-c8d2b0319bd8") + (layer "F.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c086851a-ee4a-4d94-b9fb-57268a8b1291") ) (segment - (start 128.7016 122.6) - (end 129.2167 123.1151) + (start 148.4 86.425) + (end 148.4 97.9) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "22bff11a-2b62-442b-8e31-8ea1f24630da") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "d61b555b-ab36-4179-a1b4-0d03a694051f") ) (segment - (start 128.26 122.6) - (end 128.7016 122.6) + (start 149 83.5) + (end 147.775 84.725) (width 0.2) (layer "F.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "ced9a80b-1e20-49aa-83c0-531f5a274e3d") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "dbf7fa59-0322-4cb7-a5fe-08aa1f106cff") ) (via - (at 129.2167 123.1151) + (at 147.7 98.6) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "38dfc02c-7724-4dbb-bcd2-1b5f3ff8490f") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "85ed3b56-0a8b-4146-ba6d-d824ffe69a45") + ) + (via + (at 134.7 117.7) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c0bb0415-717d-48d2-9f1e-4dd584217635") ) (segment - (start 134.8063 110.1697) - (end 139.8799 105.0961) + (start 147.7 108) + (end 142.1 113.6) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "1afad761-9ae0-4bfb-aeac-6e797ea1b298") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "1853d100-3522-4834-a9bb-eb2f88a6c67e") ) (segment - (start 133.2067 110.1697) - (end 134.8063 110.1697) + (start 142.1 113.6) + (end 141.751471 113.6) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "1fb6423c-43d1-41cf-bc98-9dfe32a42132") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "1cecf9fb-fc13-4248-8979-37bba3a67eaa") ) (segment - (start 129.1465 114.2299) - (end 133.2067 110.1697) + (start 141.262744 113.951471) + (end 137.714214 117.5) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "4abddbc8-ac39-48f0-b2b0-59a2c95f34ea") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "727810ad-a035-4023-935f-22f8f817f512") ) (segment - (start 139.8799 105.0961) - (end 139.8799 99.2055) + (start 147.7 98.6) + (end 147.7 108) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "8c7078a3-3d56-4b45-826f-93908c878b5d") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "b674e549-e96a-4247-bebc-c01bc354f93a") ) (segment - (start 129.2167 123.1151) - (end 129.1465 123.0449) + (start 137.7 117.5) + (end 137.5 117.7) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "944d2be8-04b4-4f79-a260-4c55c51df8ca") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c05f1a2f-202c-43cb-8f66-0b93a86ea8f3") ) (segment - (start 141.65 98.2) - (end 140.7233 98.2) + (start 137.5 117.7) + (end 134.7 117.7) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "d34d93b3-d621-4732-a876-6a4605e69307") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c56b55ac-4fac-46e9-89b6-4adadf7e2c22") ) (segment - (start 129.1465 123.0449) - (end 129.1465 114.2299) + (start 137.714214 117.5) + (end 137.7 117.5) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "ebe4f5e1-df2c-46fd-a7a7-af70a179ece1") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c788a34e-39a9-4798-84b2-d3d3cdd5c85f") ) (segment - (start 140.7233 98.3621) - (end 140.7233 98.2) + (start 141.4 113.951471) + (end 141.262744 113.951471) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "eca0e417-aef3-483f-85ac-f8b1b948690f") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "c7a6b37c-e1d7-4ec7-91f9-b2943e8fa9cf") ) (segment - (start 139.8799 99.2055) - (end 140.7233 98.3621) + (start 141.751471 113.6) + (end 141.4 113.951471) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/RGB_DIN") - (uuid "f55412f4-e147-4f2e-a05d-e411d9bba320") + (net "/Buttons_Direct/BTN_VOL_DN") + (uuid "e4069ed9-c8df-4997-997b-581f0517e48e") ) (segment - (start 121.4616 83.1279) - (end 121.4616 83.8045) + (start 135.65 118.35) + (end 135.6 118.3) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "01de4ce2-9154-4f23-b614-4a5922ef9278") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "c96bf5d7-c817-4dca-ae3c-ffae32d6c5ee") ) (segment - (start 123.1364 84.725) - (end 123.7597 85.3483) + (start 135.65 119.5) + (end 135.65 118.35) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "44c383f6-6425-4cac-977f-cd68cfffdc28") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "d4e9c6b0-649c-4b84-a46b-11bc4364b57c") + ) + (via + (at 135.6 118.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "db284436-5f89-4320-a7ea-5c473b83cbe3") ) (segment - (start 123.7597 89.3434) - (end 123.5578 89.5453) + (start 135.6 118.3) + (end 136.61 119.31) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "5f241953-191e-4920-af22-8f38318c1ad2") + (layer "B.Cu") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "86febbfd-2438-4739-8cf5-1973e13c1bfc") ) (segment - (start 122.7 84.725) - (end 123.1364 84.725) + (start 136.61 119.31) + (end 136.61 121.3) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "61dca9c6-5da0-4318-852c-b209566fad98") + (layer "B.Cu") + (net "/XBee/XBEE_ON_SLEEP") + (uuid "d7d1562f-bb55-429b-b8ed-46044ca26d28") ) (segment - (start 121.4616 83.8045) - (end 122.3821 84.725) + (start 136.5 119.5) + (end 136.5 118.3) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "982abf07-1913-409d-889c-61b2551c81da") + (net "/XBee/XBEE_RESET") + (uuid "3372d33e-0a03-4bbd-b5ba-d0e029c03d5a") + ) + (via + (at 136.5 118.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/XBee/XBEE_RESET") + (uuid "98788e93-586b-4107-8a52-dfbface0942c") ) (segment - (start 122.7 82.275) - (end 122.1752 82.7998) + (start 136.5 118.3) + (end 139.15 120.95) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "a4d95084-903f-46a5-a82f-1b9716de7778") + (layer "B.Cu") + (net "/XBee/XBEE_RESET") + (uuid "52913460-9451-4d17-a806-0f91a821d927") ) (segment - (start 122.3821 84.725) - (end 122.7 84.725) + (start 139.15 120.95) + (end 139.15 121.3) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "ab634ecd-680c-4962-8e43-16bb489d1964") + (layer "B.Cu") + (net "/XBee/XBEE_RESET") + (uuid "e3604593-8a99-4b0e-baa3-add3f7112137") ) (segment - (start 123.5578 89.5453) - (end 123.5578 90.4396) + (start 138.2 119) + (end 141.4 115.8) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "b3648590-cdce-407a-8fe7-05f89f826dca") + (net "/MCU_Core/PWR_HOLD") + (uuid "0bf34243-b600-4bc2-9981-8bd4b63e01bf") ) (segment - (start 123.7597 85.3483) - (end 123.7597 89.3434) + (start 138.485 74.588529) + (end 138.485 72.539999) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "bbc5a2cf-50e4-43e4-b481-667eb8ce7396") + (net "/MCU_Core/PWR_HOLD") + (uuid "1db3e63b-d7d3-4271-a9fa-b0796ffa017e") ) (segment - (start 122.1752 82.7998) - (end 121.7897 82.7998) + (start 141.4 113.951471) + (end 141.751471 113.6) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "be0dd1d2-1459-4775-924a-0166ab8b6999") + (net "/MCU_Core/PWR_HOLD") + (uuid "2097ce7d-5890-475c-b829-c5e9a6ea50bc") ) (segment - (start 121.7897 82.7998) - (end 121.4616 83.1279) + (start 136.825 76.248529) + (end 138.485 74.588529) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "cf559841-3eae-4f99-8a0b-126bca608811") - ) - (via - (at 123.5578 90.4396) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "c1fb52d8-6b1f-4b5f-827a-1f1f13fd1e69") + (net "/MCU_Core/PWR_HOLD") + (uuid "348f6de3-76c0-42e3-a994-073f34529097") ) (segment - (start 125.5957 91.7504) - (end 126.9517 93.1064) + (start 138.2 119.5) + (end 138.2 119) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "5669a844-330f-4a6e-ac00-5a624cdba5d7") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "5a3287ff-0faa-4038-b5cc-7599536bd96c") ) (segment - (start 130.6314 93.1064) - (end 131.025 93.5) + (start 136.825 84.840255) + (end 136.825 76.248529) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "7692c439-878e-49cb-b9cf-5e8e132e06f4") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "61817c01-9c98-4fda-b123-3f35bcab8fc6") ) (segment - (start 123.5578 90.7173) - (end 124.5909 91.7504) + (start 140.95 88.965255) + (end 136.825 84.840255) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "9bde2aea-d3d5-4e04-b028-9bb52b4d105c") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "72b4cbb2-270b-4dba-a8f2-9035c9be5946") ) (segment - (start 123.5578 90.4396) - (end 123.5578 90.7173) + (start 140.95 90.7) + (end 140.95 88.965255) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "c18d23ab-2b44-4c4b-8844-3d900b1890ce") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "744df1f1-4804-400b-b298-cc600628305f") ) (segment - (start 124.5909 91.7504) - (end 125.5957 91.7504) + (start 142 113.6) + (end 142 107.3) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "d18b91cf-024f-4c23-bb17-fea5147af786") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "7e18483a-dca1-448a-9ddf-87bd9dc36dab") ) (segment - (start 126.9517 93.1064) - (end 130.6314 93.1064) + (start 141.4 115.8) + (end 141.4 113.951471) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_THR_DN") - (uuid "ea2be94d-4089-43b7-906e-df0afbe5752d") + (layer "F.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "829e3cc7-19c8-4b27-92d1-33fc68d49395") ) (segment - (start 138.9845 85.98) - (end 135.7345 89.23) + (start 141.751471 113.6) + (end 142 113.6) (width 0.2) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "22b3b4b5-7d06-4929-9c7e-b1bd79bc4180") + (net "/MCU_Core/PWR_HOLD") + (uuid "b1ee0c93-5f6a-4536-a22f-738e81e468a3") + ) + (via + (at 140.95 90.7) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "01e75d0e-132e-4c32-a7ed-7e79123a0c57") + ) + (via + (at 138.485 72.539999) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "034ec525-4d56-4b3b-91b8-82fff126752d") + ) + (via + (at 142 107.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "54dfdcc4-7e5a-46db-a25d-9b3f49cfd01b") ) (segment - (start 135.7345 89.23) - (end 135.7345 92.6614) + (start 142.7 97.6) + (end 142.7 93.5) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "49dc7834-5810-4f9e-8bb6-64db285fec94") + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "09fe6f92-9e04-4ba4-9d03-c073381dc901") ) (segment - (start 146.0562 74.725) - (end 146.0562 76.888) + (start 143.2 98.1) + (end 142.7 97.6) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "59c4c0b3-de4e-4c81-8788-cd1f7892f248") + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "3f31b1e1-abb7-4e71-b528-b60fbe25a48b") ) (segment - (start 145.0697 77.8745) - (end 145.0697 82.0927) + (start 142 107.3) + (end 143.2 106.1) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "6754f3fc-e9f1-4964-99fc-0188786e0432") + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "41733a2e-2396-4c5b-9393-66bf3739c162") ) (segment - (start 141.1824 85.98) - (end 138.9845 85.98) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "90ee9024-f7b8-4997-9a2e-96732bc028b2") + (start 138.385 72.44) + (end 138.485 72.539999) + (width 0.3) + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "59dd0f51-8058-4c5b-bda6-638a82a844c7") ) (segment - (start 147.3 72.275) - (end 146.9792 72.275) + (start 143.2 106.1) + (end 143.2 98.1) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "a8605754-fbd3-472a-ab76-deede7fd30df") + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "6b699eb9-7b8d-4f12-abba-c838def9d377") ) (segment - (start 146.9792 72.275) - (end 146.0562 73.198) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "b0adc39d-2ea8-4c49-8430-a7d7ba914747") + (start 136.935 72.44) + (end 138.385 72.44) + (width 0.3) + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "89103954-78e1-436f-92b5-11159941f3b9") ) (segment - (start 146.0562 73.198) - (end 146.0562 74.725) + (start 140.95 91.75) + (end 140.95 90.7) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "c6214d40-e482-49d8-91c7-556d5b014850") + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "b6b0213f-7930-422d-abcf-9df4dbf4a136") ) (segment - (start 146.0562 76.888) - (end 145.0697 77.8745) + (start 142.7 93.5) + (end 140.95 91.75) (width 0.2) + (layer "B.Cu") + (net "/MCU_Core/PWR_HOLD") + (uuid "c221372f-870c-4836-90f0-577b1e33d84b") + ) + (segment + (start 137 124.9) + (end 138.379999 124.9) + (width 0.4) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "d88b7741-56d3-46b1-8a8d-c62bcb41da15") + (net "VBUS") + (uuid "001968e7-82a5-468f-afcb-c71d108936e4") ) (segment - (start 146.0562 74.725) - (end 147.3 74.725) - (width 0.2) + (start 122.8 100.825) + (end 125.45 98.175) + (width 0.4) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "e88af724-3a3f-4a39-9199-41855e27c868") + (net "VBUS") + (uuid "08109a67-ea68-49e8-841d-e37ba871a6b1") ) (segment - (start 145.0697 82.0927) - (end 141.1824 85.98) - (width 0.2) + (start 138.379999 124.9) + (end 139.45 123.829999) + (width 0.4) (layer "F.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "f1091827-c902-4070-af57-67db9ed7179f") + (net "VBUS") + (uuid "09f6cead-452c-4d45-9a46-89e83fbffdd2") ) - (via - (at 135.7345 92.6614) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "c5abe53e-4f83-46ba-a68d-aed20fbc2b8c") + (segment + (start 137 124.9) + (end 135.620001 124.9) + (width 0.4) + (layer "F.Cu") + (net "VBUS") + (uuid "144b367e-788f-4feb-9716-18c092bd4261") ) (segment - (start 137.025 93.5) - (end 136.1864 92.6614) - (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "cba3cbe5-f49f-4e9a-8908-88441a440c6d") + (start 139.45 123.829999) + (end 139.45 123.105) + (width 0.4) + (layer "F.Cu") + (net "VBUS") + (uuid "35f1373d-c77a-46ec-a98f-d68e0cb4bd5e") ) (segment - (start 136.1864 92.6614) - (end 135.7345 92.6614) - (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_VOL_UP") - (uuid "f4d5b290-3083-42c3-b67d-812b00b57d6f") + (start 122.8 102.3) + (end 122.8 100.825) + (width 0.4) + (layer "F.Cu") + (net "VBUS") + (uuid "66b044f3-929b-490a-ab13-461ef459825b") ) (segment - (start 141.1167 110.9816) - (end 141.875 110.2233) - (width 0.2) + (start 135.620001 124.9) + (end 134.55 123.829999) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "05245568-c660-492c-9bff-dde45d0c124e") + (net "VBUS") + (uuid "95aecc46-4db6-4662-bb0d-8026cdf23992") ) (segment - (start 145.8508 105.7783) - (end 148.0599 103.5692) - (width 0.2) + (start 122.3 102.8) + (end 122.8 102.3) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "52479802-0c02-472e-bef2-f1666036a206") + (net "VBUS") + (uuid "bda33a40-3d70-4436-8d88-3dcfc79e8990") ) (segment - (start 141.875 110.2233) - (end 141.875 109.8) - (width 0.2) + (start 134.55 123.829999) + (end 134.55 123.105) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "59545412-81be-42ab-b3d2-498f2deb5176") + (net "VBUS") + (uuid "c325b613-3859-4dd9-869c-5c6756d94e7f") ) (segment - (start 148.0599 87.8949) - (end 145.9807 85.8157) - (width 0.2) + (start 125.45 98.175) + (end 125.45 95.96005) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "8adda2c2-ca4a-4357-8aee-3bf522f12e1c") + (net "VBUS") + (uuid "c4af0a20-b8d0-4e17-908f-589616f0d0e4") ) (segment - (start 148.0599 103.5692) - (end 148.0599 87.8949) - (width 0.2) + (start 124.73995 95.25) + (end 123.75 95.25) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "f8bd0115-6168-41ba-a174-7035c6dc4328") + (net "VBUS") + (uuid "cf2d65ec-486d-4ae5-b5ee-11c49d15d9a6") ) (segment - (start 145.8508 107.6237) - (end 145.8508 105.7783) - (width 0.2) + (start 125.45 95.96005) + (end 124.73995 95.25) + (width 0.4) (layer "F.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "fee57e58-0fe0-4668-b6d2-1f121c1ff6c3") + (net "VBUS") + (uuid "f383cc5d-c5c9-4691-9174-6452812d49e9") ) (via - (at 145.8508 107.6237) + (at 123.75 95.25) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "00bfdde3-3110-4bd8-b9f7-7dfed2cb6ff8") + (net "VBUS") + (uuid "a7347dfc-56b3-4ad5-bcae-d96a4f8ab1d9") ) (via - (at 145.9807 85.8157) + (at 137 124.9) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "7c6bbb16-51c5-42ba-bc43-2226f975c9e6") + (net "VBUS") + (uuid "f1030aed-9337-4711-bbc9-70bffcedcd8b") ) (via - (at 141.1167 110.9816) + (at 122.3 102.8) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "cd8cb40d-c5c9-4a02-95d2-7004ca3b73fa") + (net "VBUS") + (uuid "f2957296-43f5-442f-8512-099cd3166926") ) (segment - (start 140.425 80.24) - (end 140.385 80.24) - (width 0.2) + (start 125.75 95.29) + (end 123.79 95.29) + (width 0.3) (layer "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "21cab7fa-2bfc-42cc-88f9-6ae702e2e603") + (net "VBUS") + (uuid "02856a9b-3f45-49dc-a38b-d7697fed0c90") ) (segment - (start 140.385 80.24) - (end 139.084999 78.94) - (width 0.2) + (start 121.47 103.93) + (end 121.2 104.2) + (width 0.4) (layer "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "480eaa46-8e29-4d43-9e93-f3aadb15a318") + (net "VBUS") + (uuid "0cdef74f-a58b-4b54-a9d4-9b5b1c88635f") ) (segment - (start 140.405 80.24) - (end 145.9807 85.8157) - (width 0.2) + (start 121.1939 106.524777) + (end 121.2 106.530877) + (width 0.4) (layer "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "d38cca98-081f-403f-827d-55894b555cab") + (net "VBUS") + (uuid "1448d256-d94e-40be-8457-2c876a1599e4") ) (segment - (start 138.285 78.94) - (end 139.084999 78.94) - (width 0.55) + (start 123.79 95.29) + (end 123.75 95.25) + (width 0.2) (layer "B.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "f4b34b13-2cf0-4566-8bfc-13808b4d731b") + (net "VBUS") + (uuid "198439d2-7773-429f-9020-240fdde58a4a") ) (segment - (start 145.8508 107.6237) - (end 144.4746 107.6237) - (width 0.2) - (layer "In1.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "02ddaab8-83aa-4c3f-bdde-38273d72f4ce") + (start 121.2 105.938777) + (end 121.1939 105.944877) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "1e5736df-58e3-4020-ae06-5ce89d570b99") ) (segment - (start 144.4746 107.6237) - (end 141.1167 110.9816) - (width 0.2) - (layer "In1.Cu") - (net "/Power_Buck/PWR_EN") - (uuid "98f3cf77-bcef-456b-82ca-8f5e77389738") + (start 122.3 102.8) + (end 121.47 103.63) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "2413d782-f49c-4d6c-8f16-410e5e58eb14") ) (segment - (start 139.975 109.8) - (end 137.5 109.8) - (width 0.8) - (layer "F.Cu") - (net "/Power_Buck/BUCK_SW") - (uuid "494a36fc-93c9-461d-94d2-06d30dfda801") + (start 121.17393 107.353337) + (end 121.2 107.379407) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "2769be11-1acd-46cb-99a9-e0538215f24a") ) (segment - (start 135.45 103.15) - (end 134.85 103.15) + (start 125.91 95.45) + (end 125.75 95.29) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "012df7c2-5f8b-4bd2-bd59-f12454edcb3d") + (layer "B.Cu") + (net "VBUS") + (uuid "3d510092-3319-49e8-bbd6-4a295b1bc800") ) (segment - (start 134.6 103.1) - (end 133 101.5) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "021c1594-4f35-47db-891c-ebf91fc6c5ae") + (start 133.6 125.6) + (end 134.245 126.245) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "4321035b-1d85-4b7c-b03e-5f842a11aa98") ) (segment - (start 134.1573 101.8556) - (end 133.7517 101.45) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "08084882-8e3d-455e-84e4-22765948492a") + (start 121.1939 105.944877) + (end 121.1939 106.524777) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "596760de-c021-45b6-884e-3a219f112b82") ) (segment - (start 135.5 103.2) - (end 135.45 103.15) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "1967d1c3-7ee2-4892-b3c9-f6ad2c492673") + (start 131.146016 124.646016) + (end 132.1 125.6) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "605fd306-d54d-4151-89c4-d8caa61fae8a") ) (segment - (start 135.7 103.25) - (end 135.65 103.2) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "213522f3-1ce1-45b5-ab0c-3480e4265fc5") + (start 125.75 124.196016) + (end 126.2 124.646016) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "678c806a-3297-45d8-8fd3-0c7a972dca90") ) (segment - (start 136.6694 101.8556) - (end 134.1573 101.8556) + (start 127.7 95.45) + (end 125.91 95.45) (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "327d2b9f-9d1d-4711-9b87-aa0aae507599") + (layer "B.Cu") + (net "VBUS") + (uuid "83ea02c6-78af-4b18-8ce1-4bbea96fb72e") ) (segment - (start 134.85 103.15) - (end 134.8 103.1) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "3491ebaf-6f3b-4aa3-a957-59b971a5297e") + (start 126.2 124.646016) + (end 131.146016 124.646016) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "8c70f03d-878e-436e-814d-7f9565799403") ) (segment - (start 135.75 103.25) - (end 135.7 103.25) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "49cc2bfc-5a11-46da-bb79-cb6ce15120c0") + (start 135.845 126.055) + (end 137 124.9) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "9fc09a8c-720d-4a55-b90e-b9eb9c85d7fa") ) (segment - (start 137.075 101.45) - (end 136.6694 101.8556) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "81620a80-a581-4a59-90ec-6c631d9b7d97") + (start 121.2 106.530877) + (end 121.2 106.747367) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "a3247838-8cbf-45d3-bebe-5e427fb1a4d3") ) (segment - (start 136.15 104.25) - (end 136.15 103.65) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "a49a8999-b5bb-4dad-b278-b6349c1d0716") + (start 132.1 125.6) + (end 133.6 125.6) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "a97e98f2-b019-498d-bd87-e99ffe2c51b8") ) (segment - (start 134.8 103.1) - (end 134.6 103.1) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "a7c2339c-1d31-47ad-af70-47da736d26ea") + (start 121.2 106.747367) + (end 121.17393 106.773437) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "b5e023d9-1ac3-4adf-bc41-064801449975") ) (segment - (start 136.15 103.65) - (end 135.75 103.25) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "a8a661fb-5744-40a7-8060-ac168cfc6b95") + (start 121.2 122.892031) + (end 122.503984 124.196016) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "bc9c3489-b5bb-49db-a22c-024223ec812f") ) (segment - (start 135.65 103.2) - (end 135.5 103.2) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "d58db328-526b-4190-864c-261fad80fd39") + (start 121.2 107.379407) + (end 121.2 122.892031) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "c6f4cc26-5f42-4488-82c3-e6bfd4c290da") ) (segment - (start 132.925 101.45) - (end 133.7517 101.45) - (width 0.2) - (layer "F.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "d7098f91-1a4b-43ce-a073-57e352bb1613") - ) - (via - (at 136.15 104.25) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "1ac919df-bec7-4c6a-ba8d-8d640583b760") + (start 121.2 104.2) + (end 121.2 105.938777) + (width 0.4) + (layer "B.Cu") + (net "VBUS") + (uuid "cc610af2-fd6b-46ff-ae90-7aa77527e865") ) (segment - (start 137.05 101.95) - (end 137.05 103.5) - (width 0.2) + (start 134.245 126.245) + (end 135.845 126.245) + (width 0.4) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "3c4f2673-a30a-447c-818b-816b3349d57f") + (net "VBUS") + (uuid "d6ba137d-d3a1-403b-b9bb-c215467ee636") ) (segment - (start 138.4 100.7) - (end 138.35 100.75) - (width 0.2) + (start 122.503984 124.196016) + (end 125.75 124.196016) + (width 0.4) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "40907838-c923-4144-ac2a-57ecd46ab7c8") + (net "VBUS") + (uuid "d7461274-5b92-4b4c-be77-4fbadbf65097") ) (segment - (start 138.35 100.75) - (end 138.15 100.75) - (width 0.2) + (start 121.47 103.63) + (end 121.47 103.93) + (width 0.4) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "4f7ff889-e92f-48f9-99b5-17f8779f4b6c") + (net "VBUS") + (uuid "e61f7dcf-71b5-4788-a1b9-832c2427c2ad") ) (segment - (start 136.7 103.75) - (end 136.65 103.8) - (width 0.2) + (start 135.845 126.245) + (end 135.845 126.055) + (width 0.4) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "6678ef12-aa13-4a31-b155-e8bdbb388bda") + (net "VBUS") + (uuid "f6e0ecc1-75e5-4f6a-8e7c-81799a40033c") ) (segment - (start 138.5 100.7) - (end 138.4 100.7) - (width 0.2) + (start 121.17393 106.773437) + (end 121.17393 107.353337) + (width 0.4) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "6bc3b56f-6987-4e8b-af2a-3ae3c9b8cf6d") + (net "VBUS") + (uuid "ff48668b-686a-4ab2-be44-cc9965ec4ec7") ) (segment - (start 137.05 103.5) - (end 136.8 103.75) + (start 135.75 123.105) + (end 135.75 122.34759) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "831e4763-5307-48c8-bb75-8b00891da554") + (layer "F.Cu") + (net "/USB_C/USB_CC1") + (uuid "69424468-0a2d-490e-b651-afa0ed2514b2") ) (segment - (start 136.6 103.8) - (end 136.15 104.25) + (start 130.82 122.08) + (end 129.2 123.7) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "83e1af8b-2878-4492-94bf-8a66920ce02c") + (layer "F.Cu") + (net "/USB_C/USB_CC1") + (uuid "7e4ceed2-d8e8-4ad5-83ab-4a871e74f3ba") ) (segment - (start 137.1 101.8) - (end 137.1 101.9) + (start 135.48241 122.08) + (end 130.82 122.08) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "88190bcd-5794-4f5d-aa52-4b5b1e750957") + (layer "F.Cu") + (net "/USB_C/USB_CC1") + (uuid "a22f710f-a840-4a77-855d-19d235099ada") ) (segment - (start 136.65 103.8) - (end 136.6 103.8) + (start 135.75 122.34759) + (end 135.48241 122.08) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "aadf51cf-20c2-4c7b-a7ad-97495964e52e") + (layer "F.Cu") + (net "/USB_C/USB_CC1") + (uuid "fdd8e054-e9ac-412b-b32e-8bc393d669f6") + ) + (via + (at 129.2 123.7) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/USB_C/USB_CC1") + (uuid "b62b4169-26ed-43dc-bde6-5877d01fd391") ) (segment - (start 138.15 100.75) - (end 137.1 101.8) + (start 129.2 123.7) + (end 130.15 123.7) (width 0.2) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "cf7a3170-0cb4-47bc-a39d-34f9cbc2dfe7") + (net "/USB_C/USB_CC1") + (uuid "56adefa5-8d05-4291-ad30-c238100b14fc") ) (segment - (start 137.1 101.9) - (end 137.05 101.95) + (start 130.15 123.7) + (end 130.265 123.815) (width 0.2) (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "d035336d-3bd1-452d-adbc-1328e7d2eaa5") + (net "/USB_C/USB_CC1") + (uuid "baebd2cb-a8aa-4f2a-b352-f7bcba49ec3e") ) (segment - (start 136.8 103.75) - (end 136.7 103.75) + (start 136.657357 121.254947) + (end 130.463578 121.254947) (width 0.2) - (layer "B.Cu") - (net "/Buttons_Direct/BTN_MACRO5") - (uuid "ec08890d-8ae2-4e21-b00d-cfb013af0f67") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "18d7ad58-e5bd-48f1-a050-65c1d8f911e2") ) (segment - (start 140.785 75.94) - (end 138.459999 75.94) + (start 126.689999 121.289999) + (end 125 119.6) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_GATE") - (uuid "1c0e1392-1308-4d7e-9b43-52bd43a7b0df") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "19981f8b-99ae-4ee7-b712-dc83b577a79b") ) (segment - (start 135.584999 78.815) - (end 134.334999 78.815) + (start 137.75 122.34759) + (end 137.251205 121.848795) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_GATE") - (uuid "281fab28-dfdd-4ecb-8039-2f76a03c22bc") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "2b74a69b-0eb4-4666-a5f7-99b967e44250") ) (segment - (start 138.459999 75.94) - (end 137.334999 77.065) + (start 125 119.6) + (end 125 117.6) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_GATE") - (uuid "42f075a7-3c00-4713-bec1-f474337b28a6") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "59981754-00c2-4026-a178-d40b77041071") ) (segment - (start 137.334999 77.065) - (end 135.584999 78.815) + (start 125.7 116.88) + (end 128.1 116.88) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_GATE") - (uuid "8910ff32-e021-46ce-a871-0e9175fbb549") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "88a138ca-ca5c-4bd2-9bd4-104fcba47cdd") ) (segment - (start 124.86125 90.539999) - (end 124.66125 90.74) + (start 130.428527 121.289999) + (end 126.689999 121.289999) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "1b054a7d-9034-4bbc-953c-c480c4bded32") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "c312082d-c9a4-4dae-9d8e-84eff4c161f9") ) (segment - (start 124.0613 86.915) - (end 124.0612 86.9151) + (start 137.75 123.105) + (end 137.75 122.34759) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "274d4270-36c9-4b9c-8b5d-05bf9703c7f1") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "c5760794-2bdc-42c6-b577-ced71bf743a6") ) (segment - (start 124.86125 88.965) - (end 124.86125 90.539999) + (start 137.20241 121.8) + (end 137.2 121.8) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "5be04e45-70f6-4513-83b9-aa479bb48846") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "cdadee1a-9030-4385-834b-804841a96115") ) (segment - (start 124.8613 89.1272) - (end 124.8613 88.965) + (start 137.251205 121.848795) + (end 136.657357 121.254947) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "5fa64d2a-fefa-411f-bfaf-437616eaef15") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "d2166adc-e902-4a9f-aa15-498e111e6edc") ) (segment - (start 124.86125 87.715) - (end 124.86125 88.965) + (start 137.251205 121.848795) + (end 137.20241 121.8) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "6be71606-780b-4ff9-af04-0f914e451032") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "d30a0904-6702-4162-9d3e-c0a9010a1a62") ) (segment - (start 124.861 89.1275) - (end 124.8613 89.1272) + (start 136.75 122.25) + (end 136.75 123.105) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "a014d864-562b-4794-bf08-1a01f46b7e89") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "d5e5910c-e8c6-408c-a4d1-e1d3a59689bc") ) (segment - (start 124.6613 90.7397) - (end 124.6613 90.74) + (start 130.463578 121.254947) + (end 130.428527 121.289999) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "aa50ad2d-853d-4670-bbeb-f443d3fc5f0d") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "e511cf3b-d215-4565-a049-a8fdc5b88e0e") ) (segment - (start 124.06125 86.914999) - (end 124.86125 87.715) + (start 137.2 121.8) + (end 136.75 122.25) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_INV_BASE") - (uuid "d931b522-b282-4cfa-afd0-45be632f50d1") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "f2ec1e3c-a780-4c04-96b6-50f9f152522c") ) (segment - (start 132.334999 75.44) - (end 132.334999 74.9) + (start 125 117.6) + (end 125.7 116.88) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "0086efc9-dba7-4e85-b44a-5c2f5f926b0c") + (layer "F.Cu") + (net "/MCU_Core/USB_DP") + (uuid "f663b833-4127-400d-b123-8d17fc380bc5") ) (segment - (start 133.634999 74.59) - (end 133.634999 72.44) + (start 138.75 122.380001) + (end 139.050001 122.08) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "0f1c2aab-b7a9-4c22-afef-2ef05a3408b7") + (layer "F.Cu") + (net "/USB_C/USB_CC2") + (uuid "0d739b6e-6c54-422c-9033-800928a3c006") ) (segment - (start 132.334999 75.889999) - (end 133.384999 76.94) + (start 139.050001 122.08) + (end 141.061371 122.08) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "38c2a9ef-d446-4118-afe7-94904f9464a1") + (layer "F.Cu") + (net "/USB_C/USB_CC2") + (uuid "27401645-0a83-430a-82e3-d81c74a07534") ) (segment - (start 133.935 74.889999) - (end 133.634999 74.59) + (start 138.75 123.105) + (end 138.75 122.380001) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "47b31948-d3b8-4ba7-bc30-1ce5b6c257e5") + (layer "F.Cu") + (net "/USB_C/USB_CC2") + (uuid "2d9f5abf-7788-43de-a622-5a7352160641") ) (segment - (start 134.524999 74.889999) - (end 133.935 74.889999) + (start 142.3 123.318629) + (end 142.3 124.9) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "4a0c5374-210a-4074-bfd4-e29a5fcca8d3") + (layer "F.Cu") + (net "/USB_C/USB_CC2") + (uuid "3988b311-ff40-4e11-b055-d22146a96c6a") ) (segment - (start 132.785 75.44) - (end 133.634999 74.59) + (start 141.061371 122.08) + (end 142.3 123.318629) (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "58587a33-3e47-43d1-9445-502e3bd48529") + (layer "F.Cu") + (net "/USB_C/USB_CC2") + (uuid "b72dd88c-e478-4d3d-91bc-af0e132172ca") + ) + (via + (at 142.3 124.9) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "/USB_C/USB_CC2") + (uuid "3b0393e4-1bd6-4946-9ad8-d71c7e92f856") ) (segment - (start 132.334999 75.44) - (end 132.785 75.44) + (start 142.3 124.9) + (end 142.3 125.03) (width 0.2) (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "6f193fb2-f87b-4c73-955b-a136db80ce3d") + (net "/USB_C/USB_CC2") + (uuid "b3efc332-7d84-4790-be51-f188c3508fde") ) (segment - (start 132.334999 76.49) - (end 130.134999 78.69) + (start 142.3 125.03) + (end 141.265 126.065) (width 0.2) (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "86dd4db4-8582-4bc2-b42c-875e38a5c5f4") + (net "/USB_C/USB_CC2") + (uuid "c965e404-7434-40b5-9722-38d4d3edbb3e") ) (segment - (start 132.334999 75.889999) - (end 132.334999 75.44) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "ab7a71e7-a5e5-4da8-b841-c4a5886647e5") + (start 129.7 100.8) + (end 129.7 93.35) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "0b172c95-e72a-4357-afe5-f40fa4b8f8d8") ) (segment - (start 132.334999 75.889999) - (end 132.334999 76.49) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "adedd923-2229-4da4-90bc-da09315f1f94") + (start 129.8 100.9) + (end 129.7 100.8) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "2f7b5fa2-9133-4065-abbb-ecb101457dcf") ) (segment - (start 132.334999 74.9) - (end 132.795 74.44) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_LATCH_G") - (uuid "b415ab68-d7a4-46a8-ac79-260a26288399") + (start 144.6 86.3) + (end 144.6 84.406192) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "385a2d64-f8fc-4f4f-bf6b-693ebf647f92") ) (segment - (start 125.9363 85.965) - (end 125.9362 85.9651) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "05eac010-bbb4-4a93-9843-15a2f7f1acf5") + (start 144.6 90.45) + (end 144.8 90.65) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "68022ab8-0f14-4a96-849c-87cb7e335ad2") ) (segment - (start 127.53625 88.514999) - (end 127.53625 87.565) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "071a5a29-3865-4381-be5a-0acb86da7ced") + (start 142.1 81.906192) + (end 142.1 79.3) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "6a665381-4687-4ae2-9b4e-82762fba76cc") ) (segment - (start 126.835 78.69) - (end 125.936 79.589) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "14a0564f-2405-4f76-9416-5b485d99b770") + (start 144.6 86.3) + (end 144.6 90.45) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "de2e08da-4f3d-41b1-8f39-274d94ca6231") ) (segment - (start 128.46125 90.704999) - (end 128.46125 88.514999) - (width 0.2) - (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "964c29c5-2a66-458c-8ad8-749f0b35eb7f") + (start 144.6 84.406192) + (end 142.1 81.906192) + (width 0.4) + (layer "F.Cu") + (net "VSYS") + (uuid "e33b3043-a88b-4e08-84b1-f0e962e81f9e") + ) + (via + (at 129.7 93.35) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "VSYS") + (uuid "3eb849e3-870e-48af-9070-8422178a29c7") + ) + (via + (at 142.1 79.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "VSYS") + (uuid "40ca9c44-a4f1-4dcd-908e-50cc1388286b") + ) + (via + (at 144.8 90.65) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "VSYS") + (uuid "7688c9ac-b849-493a-88c2-60885ed7d8c9") + ) + (via + (at 144.6 86.3) + (size 0.6) + (drill 0.3) + (layers "F.Cu" "B.Cu") + (net "VSYS") + (uuid "f8473503-d4f7-4bad-909f-663ae2f9187f") ) (segment - (start 128.46125 88.514999) - (end 127.53625 88.514999) - (width 0.2) + (start 135.35 92.65) + (end 133.75 94.25) + (width 0.3) (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "9e0cc898-90ad-49d9-9ca4-ab4883f39194") + (net "VSYS") + (uuid "0399643b-41cb-4b79-9d79-751972c369f4") ) (segment - (start 125.936 79.589) - (end 125.936 85.965) + (start 129.8 94.8) + (end 130.35 94.25) (width 0.2) (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "d02e53f1-9c24-4504-9b45-c8d4938f6f85") + (net "VSYS") + (uuid "18d14523-94bc-44d2-8eb9-887c4f9154ec") ) (segment - (start 127.53625 87.565) - (end 125.93625 85.965) + (start 129.7 93.35) + (end 128.4613 92.1113) (width 0.2) (layer "B.Cu") - (net "/Power_Control/PWR_BTN_TRIGGER") - (uuid "e097a4c9-6d53-41a0-bb4a-65cc05a42abb") + (net "VSYS") + (uuid "1acc6fb1-bcd5-4a40-8045-362469bd6664") ) (segment - (start 141.65 97.1) - (end 142.5767 97.1) - (width 0.2) + (start 137.113604 92.65) + (end 135.35 92.65) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "0b5562b0-95e6-4ae6-9dea-9e9185c9c128") + (net "VSYS") + (uuid "24b5b3fd-8ad8-4941-885a-5d092da79e81") ) (segment - (start 148.25 104.8) - (end 149.0767 104.8) + (start 139.235 77.065) + (end 140.68 77.065) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "83454d40-5d85-46fb-b333-17dfe947304a") + (net "VSYS") + (uuid "2ba6fcb0-39b3-4c1b-9923-7f3aa41775a3") ) (segment - (start 144.1 104.8) - (end 148.25 104.8) + (start 126.868125 90.131875) + (end 128.46125 91.725) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "8858024c-6f11-4c1e-b71b-3120b04d53a6") + (net "VSYS") + (uuid "4ab519b2-c395-4617-a658-d692b8a9c47b") ) (segment - (start 142.5767 97.2967) - (end 144.565 99.285) - (width 0.2) + (start 146.525 93.475) + (end 146.375 93.475) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "aaa04def-d9c6-4526-a193-edb4d09a2ec9") + (net "VSYS") + (uuid "61613c46-9796-4d9f-86f8-28d96a6d45f7") ) (segment - (start 142.5767 97.1) - (end 142.5767 97.2967) + (start 131.25 94.25) + (end 133.75 94.25) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "b116586a-f2c2-49d4-b4cc-cfa45ca959c3") + (net "VSYS") + (uuid "626ff153-778e-4583-9221-22b58fb9e58a") ) (segment - (start 149.0767 100.1793) - (end 148.1824 99.285) + (start 125.88125 89.145) + (end 125.88125 88.965) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "cb4a4e70-40ce-4881-9e93-f9eb2a2505fc") + (net "VSYS") + (uuid "63932cc1-8ef9-4f70-aeb5-ff6bfd759f68") ) (segment - (start 149.0767 104.8) - (end 149.0767 100.1793) - (width 0.2) + (start 146.525 93.475) + (end 146.525 91.575) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "de052fcf-1589-49cb-9b74-3236ac03b19b") + (net "VSYS") + (uuid "6ddd411c-740e-4281-80d7-d44339d1cb7d") ) (segment - (start 148.1824 99.285) - (end 144.565 99.285) - (width 0.2) + (start 146.525 91.575) + (end 146.5 91.55) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/MCU_BOOT") - (uuid "f13b7fbc-f102-48e9-b41a-972650462c01") + (net "VSYS") + (uuid "7195b701-6e09-4dee-b1d5-1faa95c9b455") ) - (via - (at 127.5257 92.5047) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "1ce2e275-2d60-43c4-86ef-a0899e8fdcaf") + (segment + (start 145.6 90.65) + (end 146.5 91.55) + (width 0.4) + (layer "B.Cu") + (net "VSYS") + (uuid "779b0863-a2bd-4205-88d3-67b5866ac666") ) - (via - (at 129.8617 101.9822) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "33e9b7db-741c-4b02-b581-542743e05e14") + (segment + (start 140.785 77.985) + (end 142.1 79.3) + (width 0.4) + (layer "B.Cu") + (net "VSYS") + (uuid "81fe66d7-f0af-4cb9-b19b-1cafcd3c952a") ) (segment - (start 133.1267 101.0107) - (end 132.6709 101.4665) + (start 128.4613 92.1113) + (end 128.4613 91.725) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "07906176-e1ea-4aae-ad25-6243b29d8017") + (net "VSYS") + (uuid "9e4f8b0e-50d7-43e2-b80c-1c71b3157428") ) (segment - (start 129.75 91.76) - (end 130.3724 91.1376) - (width 0.2) + (start 140.785 76.96) + (end 140.785 77.985) + (width 0.4) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "14a9c791-a1a8-4719-a055-3f53d270b8f7") + (net "VSYS") + (uuid "a82ed588-951c-450c-b40e-1ea56a1e06df") ) (segment - (start 129.0053 92.5047) - (end 127.5257 92.5047) + (start 129.7 93.35) + (end 132.85 93.35) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "40ebe912-7ebc-4e3e-b1e6-88888f0c1264") + (net "VSYS") + (uuid "af613e94-2a61-43a6-a842-97633ccc6f61") ) (segment - (start 130.3724 91.1376) - (end 131.3676 91.1376) + (start 130.35 94.25) + (end 131.25 94.25) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "546fe3aa-0ef4-4e87-a0b3-feed7a5666fc") + (net "VSYS") + (uuid "b3693555-99df-4a28-9d27-08c1cacfca53") ) (segment - (start 133.1267 97.7017) - (end 133.1267 101.0107) + (start 126.868125 90.131875) + (end 125.88125 89.145) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "5aad5742-5fe5-4c14-867e-1b506f36c661") + (net "VSYS") + (uuid "ca1cb295-7345-4906-addd-d2d9e8416f1b") ) (segment - (start 129.75 91.76) - (end 129.0053 92.5047) - (width 0.2) + (start 143.463604 86.3) + (end 137.113604 92.65) + (width 0.3) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "67d656f4-be72-487f-a759-d2148d024bd1") + (net "VSYS") + (uuid "db184b2c-dc96-4edf-9784-520a7302f8a0") ) (segment - (start 130.3774 101.4665) - (end 129.8617 101.9822) + (start 129.8 94.8) + (end 129.8 95.45) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "8342c731-e815-4d66-b412-6904dc3dc285") + (net "VSYS") + (uuid "e19bd3b2-67bb-4fa6-bb7a-9a47d6bb537d") ) (segment - (start 131.3676 91.1376) - (end 131.98 91.75) + (start 132.85 93.35) + (end 133.75 94.25) (width 0.2) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "84646664-72c7-4c44-b1cb-2cee3b121729") + (net "VSYS") + (uuid "e33dece0-1140-4354-8479-2268d7203207") ) (segment - (start 132.525 97.1) - (end 133.1267 97.7017) - (width 0.2) + (start 144.6 86.3) + (end 143.463604 86.3) + (width 0.3) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "a4d800c3-17fe-4266-8a14-3258df4aa025") + (net "VSYS") + (uuid "e38b1759-e4d4-463b-b395-757d6ceea7e8") ) (segment - (start 132.6709 101.4665) - (end 130.3774 101.4665) - (width 0.2) + (start 144.8 90.65) + (end 145.6 90.65) + (width 0.4) (layer "B.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "cd6e2544-6555-4609-aca1-ac0ec4e2da25") + (net "VSYS") + (uuid "ef278462-8974-4b88-8ac1-a41dc7aeed6d") ) (segment - (start 129.8617 101.9822) - (end 127.5257 99.6462) + (start 137.334999 77.065) + (end 135.584999 78.815) (width 0.2) - (layer "In1.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "29223027-cc74-41a6-9309-34ee59fa10ac") + (layer "B.Cu") + (net "/Power_Control/PWR_GATE") + (uuid "2215d584-241b-4ff5-ac03-69b8ed38f121") ) (segment - (start 127.5257 99.6462) - (end 127.5257 92.5047) + (start 138.459999 75.94) + (end 137.334999 77.065) (width 0.2) - (layer "In1.Cu") - (net "/Hall_Trigger/TRIG_ADC") - (uuid "e15b54f7-0e27-442b-8bf0-726d5bec3b2a") + (layer "B.Cu") + (net "/Power_Control/PWR_GATE") + (uuid "580e42b4-7d5c-4a7b-b97d-1d7a157780ca") ) (segment - (start 140.522 87.5837) - (end 145.7674 82.3383) + (start 135.584999 78.815) + (end 134.334999 78.815) (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "18fb52c5-fa92-40f8-a735-12679642693d") + (layer "B.Cu") + (net "/Power_Control/PWR_GATE") + (uuid "58ab2334-5fb4-4088-83e3-2a5cbe3db112") ) (segment - (start 145.7674 77.9856) - (end 147.0148 76.7382) + (start 140.785 75.94) + (end 138.459999 75.94) (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "26a2e31f-5402-47a3-9fd8-0bc7e8511e60") + (layer "B.Cu") + (net "/Power_Control/PWR_GATE") + (uuid "b1af21c6-21e3-414f-9b1a-9f709a3edcd2") ) (segment - (start 145.7674 82.3383) - (end 145.7674 77.9856) - (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "3ac0aa49-3777-40d8-bfd9-65abc146e8f5") + (start 149.3 88.5) + (end 149.108679 88.5) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "0713fc2f-682c-41dd-b1fe-46eee755db47") ) (segment - (start 147.0148 76.7382) - (end 147.0148 76.1702) + (start 140.425 80.24) + (end 140.425 81.01) (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "912c0ccd-b354-4117-b7f5-04b1cbf4d0bb") + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "0bda428c-568f-4e6b-b250-990ae984a606") ) (segment - (start 140.522 96.6235) - (end 140.522 87.5837) - (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "ba4b47d4-8cfa-430b-be6e-1eb2281ce35e") + (start 141.643679 81.035) + (end 140.4 81.035) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "38e5df68-7c5a-4d5f-869c-05b4aab3948f") ) (segment - (start 139.6368 97.5087) - (end 140.522 96.6235) - (width 0.2) - (layer "F.Cu") - (net "ACCEL_INT1") - (uuid "cd439167-3d73-4ae9-8795-87aa3807fcbd") + (start 138.285 80.985) + (end 138.285 78.94) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "449226c9-8975-4163-9db0-0a2963acefa9") ) - (via - (at 129.8714 99.6937) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "ACCEL_INT1") - (uuid "8faec230-7bde-4a94-9b0f-197d9e7df1cc") + (segment + (start 140.4 81.035) + (end 138.335 81.035) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "557a1e0b-80cd-4bc1-88b6-967d73203715") ) - (via - (at 139.6368 97.5087) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "ACCEL_INT1") - (uuid "af3a7338-21c8-4487-97a9-5330a1fd2264") + (segment + (start 149.108679 88.5) + (end 141.643679 81.035) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "829d91a6-32cc-42bb-b11e-ebf7dd1d8344") ) - (via - (at 147.0148 76.1702) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "ACCEL_INT1") - (uuid "efd017cc-fd40-4f09-8578-1e398f2e7127") + (segment + (start 148.425 95.75) + (end 149.3 94.875) + (width 0.55) + (layer "B.Cu") + (net "/Power_Buck/PWR_EN") + (uuid "91667f8f-61c7-4152-802d-7dfe1875a50d") ) (segment - (start 145.8625 68.55) - (end 147.0148 69.7023) + (start 140.425 81.01) + (end 140.4 81.035) (width 0.2) (layer "B.Cu") - (net "ACCEL_INT1") - (uuid "46d35623-883a-434d-a2c1-5dd6eb47f5ee") + (net "/Power_Buck/PWR_EN") + (uuid "a505612b-4091-4da4-93fd-7723d0272629") ) (segment - (start 129.8714 99.6937) - (end 130.8313 99.6937) - (width 0.2) + (start 149.3 94.875) + (end 149.3 88.5) + (width 0.55) (layer "B.Cu") - (net "ACCEL_INT1") - (uuid "7f727bd3-7a73-40dd-aed5-5a4c6329f8a7") + (net "/Power_Buck/PWR_EN") + (uuid "bebdb51f-ee19-4133-b31d-ff96eaa81d5a") ) (segment - (start 147.0148 69.7023) - (end 147.0148 76.1702) - (width 0.2) + (start 138.335 81.035) + (end 138.285 80.985) + (width 0.55) (layer "B.Cu") - (net "ACCEL_INT1") - (uuid "c3fae556-076d-4aa3-a8b1-0729c985e16d") + (net "/Power_Buck/PWR_EN") + (uuid "c5ff0add-0a06-4eae-919e-b3a32d0f3d25") ) (segment - (start 130.8313 99.6937) - (end 131.025 99.5) + (start 140.425 80.24) + (end 140.385 80.24) (width 0.2) (layer "B.Cu") - (net "ACCEL_INT1") - (uuid "dc496554-1dee-4f92-9964-4f7f1ae1b6a9") + (net "/Power_Buck/PWR_EN") + (uuid "fc2e6b01-4ecf-46d0-a024-d09c1f59c1f2") ) (segment - (start 139.6368 97.5087) - (end 132.0564 97.5087) - (width 0.2) - (layer "In1.Cu") - (net "ACCEL_INT1") - (uuid "3105ac48-9c31-4379-b71e-0e642e41ce53") + (start 137.7 99.4) + (end 138.6 100.3) + (width 0.55) + (layer "F.Cu") + (net "VBAT") + (uuid "0e310dd2-4725-4343-a64c-97be117aebb0") ) (segment - (start 132.0564 97.5087) - (end 129.8714 99.6937) - (width 0.2) - (layer "In1.Cu") - (net "ACCEL_INT1") - (uuid "c7ddbce5-922a-4886-a630-fd4b49e4272e") + (start 146.8 99) + (end 148.4 100.6) + (width 0.55) + (layer "F.Cu") + (net "VBAT") + (uuid "20421ad9-5f34-4f30-8ce7-effc7bc32e5d") ) (segment - (start 135 61.2691) - (end 139.0932 65.3623) - (width 0.2) + (start 148.4 108.2) + (end 147.3 109.3) + (width 0.55) (layer "F.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "5482f23b-8f9b-4f25-a683-ca617e12fe14") + (net "VBAT") + (uuid "8d8ae42b-7fdd-4a2d-b857-0c83cee0a64e") ) (segment - (start 139.0932 65.3623) - (end 139.0932 77.5662) - (width 0.2) + (start 148.4 100.6) + (end 148.4 108.2) + (width 0.55) (layer "F.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "80a33ab1-0086-4429-80f1-797165939a7c") + (net "VBAT") + (uuid "90cfccc9-ad77-444e-9597-2ef6686c04b8") ) (segment - (start 134.1053 82.5541) - (end 134.1053 87.3051) - (width 0.2) + (start 137.7 99) + (end 137.7 99.4) + (width 0.55) (layer "F.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "a827b807-08d2-484d-9c64-5f4f8a03e442") + (net "VBAT") + (uuid "a41f02f6-8423-4c68-be66-c32b02d8358f") ) (segment - (start 139.0932 77.5662) - (end 134.1053 82.5541) - (width 0.2) + (start 139.9 99) + (end 146.8 99) + (width 0.55) (layer "F.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "f348db8d-f8d2-4fbd-805c-a115822a87e8") + (net "VBAT") + (uuid "aa7b477d-ba57-49fd-9ece-5c612e4ca7e9") ) - (via - (at 134.775 95.0964) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "223f1c32-f3b0-42c2-91dc-c9ee3a39a8f2") + (segment + (start 138.6 100.3) + (end 139.9 99) + (width 0.55) + (layer "F.Cu") + (net "VBAT") + (uuid "b63c3d67-ce7c-4153-a1ac-7cd53e122ac7") + ) + (segment + (start 135.9 99) + (end 137.7 99) + (width 0.55) + (layer "F.Cu") + (net "VBAT") + (uuid "ee39a041-7527-4b8e-bb4f-316059526d1b") ) (via - (at 135 61.2691) + (at 135.9 99) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "760a3b45-b4e4-4137-befd-a9cda4c615c8") + (net "VBAT") + (uuid "5f858bca-501c-4cf8-842e-b7388d2b56f9") ) (via - (at 134.1053 87.3051) + (at 147.3 109.3) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "c55b51aa-d221-444b-8902-ad052b5ef35f") + (net "VBAT") + (uuid "9f67c3e8-9e3d-409e-9255-60ea1dd659ca") ) (segment - (start 135.8989 62.3739) - (end 135.8989 61.973) - (width 0.2) + (start 135.85 98.95) + (end 135.9 99) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "068b9d01-e82d-4022-a766-75c3380dc1fe") + (net "VBAT") + (uuid "1d66d430-ff10-4fa3-aed0-8a027a771138") ) (segment - (start 135.525 93.5) - (end 134.775 94.25) + (start 131.075 95.85) + (end 129.8 95.85) (width 0.2) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "0e530600-67e9-43db-86ba-53847dfb4e90") + (net "VBAT") + (uuid "1d85ab5a-5ffe-4382-a5bc-5452e2ebdeb0") ) (segment - (start 135.8989 61.973) - (end 135.4137 61.4878) - (width 0.2) + (start 145.2 119.176016) + (end 145.2 123.1) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "1ae6825f-b009-4918-b23d-f6dd8d91c204") + (net "VBAT") + (uuid "25fffa91-a2f1-402f-af8d-b068f6c0c51f") ) (segment - (start 134.6039 61.4878) - (end 133.775 62.3167) - (width 0.2) + (start 132.25 97.025) + (end 131.075 95.85) + (width 0.3) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "206ab676-5027-4545-86f1-2e63ac1705fc") + (net "VBAT") + (uuid "2691193f-f01b-4936-8b09-efb60196a090") ) (segment - (start 135.4137 61.4878) - (end 135 61.4878) - (width 0.2) + (start 132.25 97.75) + (end 133.45 98.95) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "45c5e993-cc99-4cf1-893e-23841f518f8b") + (net "VBAT") + (uuid "3e923c28-4a6d-443b-b83c-c1faeead56af") ) (segment - (start 133.775 62.3167) - (end 133.775 62.7) - (width 0.2) + (start 133.45 98.95) + (end 135.85 98.95) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "68e03267-074c-4d44-a1e5-6935af544b6a") + (net "VBAT") + (uuid "9a7701ca-9da3-47c7-a347-ab26a51d2eb0") ) (segment - (start 135 61.4878) - (end 134.6039 61.4878) - (width 0.2) + (start 132.25 97.75) + (end 132.25 97.025) + (width 0.3) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "6d375b84-f377-477a-a8bf-6754d38cc9c9") + (net "VBAT") + (uuid "c8a14447-3963-4711-a6fe-039f2882daec") ) (segment - (start 134.775 94.25) - (end 134.775 95.0964) - (width 0.2) + (start 147.3 109.3) + (end 147.3 117.076016) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "877810dd-9506-467a-9c89-725f95b00192") + (net "VBAT") + (uuid "d59d2b67-ca1c-4774-88be-47c3dc209da1") ) (segment - (start 136.225 62.7) - (end 135.8989 62.3739) - (width 0.2) + (start 147.3 117.076016) + (end 145.2 119.176016) + (width 0.55) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "e85e312e-a74c-4199-9955-a717691ac68a") + (net "VBAT") + (uuid "eb26d8c2-9a0d-4f18-b2ec-ecc195f04cd8") ) (segment - (start 135 61.2691) - (end 135 61.4878) + (start 124.06125 86.914999) + (end 124.86125 87.715) (width 0.2) (layer "B.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "fd3265c2-863f-45a7-ab69-1479714a8629") + (net "/Power_Control/PWR_BTN_INV_BASE") + (uuid "5adb57c8-1966-4adf-8c60-058614c8ffeb") ) (segment - (start 134.1032 92.0726) - (end 134.1032 94.4246) + (start 124.86125 88.965) + (end 124.86125 90.539999) (width 0.2) - (layer "In1.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "55753ead-e0eb-4199-a2c3-d5206e7e768f") + (layer "B.Cu") + (net "/Power_Control/PWR_BTN_INV_BASE") + (uuid "6d930117-44cf-4a2a-a579-fe9859af71ac") ) (segment - (start 134.1032 94.4246) - (end 134.775 95.0964) + (start 124.86125 87.715) + (end 124.86125 88.965) (width 0.2) - (layer "In1.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "7ab681c6-0851-4189-8113-ccb22197260c") + (layer "B.Cu") + (net "/Power_Control/PWR_BTN_INV_BASE") + (uuid "8cf75809-db73-4213-9379-103b85dcfd16") ) (segment - (start 134.1053 87.3051) - (end 134.1533 87.3531) + (start 124.86125 90.539999) + (end 124.66125 90.74) (width 0.2) - (layer "In1.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "95928c39-960d-40c3-9a2b-8de117d1bc96") + (layer "B.Cu") + (net "/Power_Control/PWR_BTN_INV_BASE") + (uuid "b8a0c5e9-6bb5-473e-beca-40fd5eb6d9cf") ) (segment - (start 134.1533 87.3531) - (end 134.1533 92.0225) + (start 132.334999 75.44) + (end 132.334999 74.9) (width 0.2) - (layer "In1.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "a0222bf1-8a9e-4d8a-b39c-80e6cb4ac3a2") + (layer "B.Cu") + (net "/Power_Control/PWR_LATCH_G") + (uuid "0358d82e-fe9b-48cd-a93a-ae881af1ed7f") ) (segment - (start 134.1533 92.0225) - (end 134.1032 92.0726) + (start 132.334999 75.44) + (end 132.785 75.44) (width 0.2) - (layer "In1.Cu") - (net "/Buttons_Direct/BTN_TRIG_DIG") - (uuid "e74589c6-d4d3-40dd-9e6a-b965348d47a4") + (layer "B.Cu") + (net "/Power_Control/PWR_LATCH_G") + (uuid "088c97c1-22c7-490e-9713-bdb17d03dbf3") ) (segment - (start 148.791 111.9746) - (end 148.791 109.108) + (start 132.334999 75.889999) + (end 132.334999 76.49) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "022fdf2e-5878-489c-9be9-02d8ab926fc2") + (net "/Power_Control/PWR_LATCH_G") + (uuid "2653c051-b081-45b9-bc54-cd093183d3ad") ) (segment - (start 143.8711 105.8876) - (end 142.1713 104.1878) + (start 132.334999 75.889999) + (end 132.334999 75.44) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "0a75e713-7d99-48d0-ba7b-6b393466fb04") + (net "/Power_Control/PWR_LATCH_G") + (uuid "27dc407c-c53c-405b-ba57-9b059c2ce0f7") ) (segment - (start 142.1713 102.3941) - (end 142.5767 101.9887) + (start 132.334999 76.49) + (end 130.134999 78.69) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "1244c0cc-112a-47d4-b086-1edc173ccba3") + (net "/Power_Control/PWR_LATCH_G") + (uuid "36b5a79f-36b5-4bb5-a6af-8a47eacdd20f") ) (segment - (start 145.5706 105.8876) - (end 143.8711 105.8876) + (start 133.634999 74.59) + (end 133.634999 72.44) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "2756f2b5-5ea9-4ea5-8d45-b5ada4a1b657") + (net "/Power_Control/PWR_LATCH_G") + (uuid "4fbfac4c-3eb0-4089-b696-b7aeaada4cc9") ) (segment - (start 147.2606 113.505) - (end 148.791 111.9746) + (start 132.785 75.44) + (end 133.634999 74.59) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "28066bd9-cbe1-4e4b-9b7c-0b27c9737910") + (net "/Power_Control/PWR_LATCH_G") + (uuid "aa3cfb31-88ec-45f1-a98a-e0944ed87e46") ) (segment - (start 146.935 113.505) - (end 147.2606 113.505) + (start 133.935 74.889999) + (end 133.634999 74.59) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "2c784022-689e-4544-8b2f-68be8b03187f") + (net "/Power_Control/PWR_LATCH_G") + (uuid "b1b34b35-d266-44b0-a617-d741e7713d83") ) (segment - (start 141.65 101.5) - (end 142.5767 101.5) + (start 134.524999 74.889999) + (end 133.935 74.889999) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "816114c9-8bf5-4373-b477-70a5368410a7") + (net "/Power_Control/PWR_LATCH_G") + (uuid "ea0ca677-5376-47f5-beed-4a85fc51a65a") ) (segment - (start 148.791 109.108) - (end 145.5706 105.8876) + (start 132.334999 75.889999) + (end 133.384999 76.94) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "909ea237-5eac-4031-ac2b-11db102e7a93") + (net "/Power_Control/PWR_LATCH_G") + (uuid "edc3f868-8dcb-4bea-a924-43b05d629148") ) (segment - (start 142.5767 101.9887) - (end 142.5767 101.5) + (start 132.334999 74.9) + (end 132.795 74.44) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "98833e79-cce7-404e-9934-b9db28886770") + (net "/Power_Control/PWR_LATCH_G") + (uuid "f51e4a12-12c4-41ee-8e58-d4c90d891411") ) (segment - (start 142.1713 104.1878) - (end 142.1713 102.3941) + (start 127.53625 88.514999) + (end 127.53625 87.565) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDIO") - (uuid "b38d3072-8f2d-4d4a-9387-fbb7a663ca81") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "4e3881d0-6a1c-4c89-84bf-3bb19376ae0a") ) (segment - (start 140.3059 106.9466) - (end 140.3059 99.7174) + (start 126.3 85.6013) + (end 125.9363 85.965) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "1878ed4b-ac4f-4506-895b-fec0f140933d") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "7ba492be-7d98-4483-beef-b99369c51c8f") ) (segment - (start 144.1 100.7) - (end 143.2733 100.7) + (start 128.46125 90.704999) + (end 128.46125 88.514999) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "497b92f7-d8c8-41c2-9046-377b25080d7f") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "aa4b4664-a227-42f2-a258-c084e68ff096") ) (segment - (start 148.25 100.7) - (end 144.1 100.7) + (start 126.835 78.69) + (end 126.3 79.225) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "52e4971b-86f2-4504-9b43-6c8140ed3ac2") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "ac0f4e60-d8fc-4a1c-8ae1-315781f28f73") ) (segment - (start 141.65 99.3) - (end 140.7233 99.3) + (start 127.53625 87.565) + (end 125.93625 85.965) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "5cbe5c26-d245-4451-89cf-b4a4f262e22c") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "b8a93b52-466d-4234-a7c2-833a229e035c") ) (segment - (start 141.65 99.3) - (end 142.5767 99.3) + (start 128.46125 88.514999) + (end 127.53625 88.514999) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "67c1108d-20bd-4bbb-bdff-2ce344e11765") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "d159cd54-f4ff-446d-8e60-a7b0af9943d8") ) (segment - (start 142.5767 100.0034) - (end 143.2733 100.7) + (start 126.3 79.225) + (end 126.3 85.6013) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "811651ef-e605-4a39-8529-858e3099cf62") + (net "/Power_Control/PWR_BTN_TRIGGER") + (uuid "f1384c57-198c-4759-924f-33099b49f8ec") ) (segment - (start 140.3059 99.7174) - (end 140.7233 99.3) + (start 124.35 101.25) + (end 122.28 101.25) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "957122c1-1644-4d30-b28f-ce901400ea1e") + (net "/Power_Charger/CHG_TS") + (uuid "af3c1557-3b83-41eb-8959-4b7f4868a299") ) (segment - (start 142.5767 99.3) - (end 142.5767 100.0034) + (start 127.7 97.05) + (end 127.7 97.9) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "a6d5ebee-b2d8-4b4f-b54c-b7316211fa77") + (net "/Power_Charger/CHG_TS") + (uuid "daa9503f-f26d-417c-ab4b-2e8448e7274a") ) (segment - (start 145.665 112.235) - (end 145.5943 112.235) + (start 127.7 97.9) + (end 124.35 101.25) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "c59edc2e-d141-4275-b8c0-fe04fdfc7478") + (net "/Power_Charger/CHG_TS") + (uuid "f656c177-028b-4e67-8cc4-856f2b60649a") ) (segment - (start 145.5943 112.235) - (end 140.3059 106.9466) + (start 125.784314 99.25) + (end 125.284314 99.75) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/MCU_RESET") - (uuid "e7203082-1843-4c0a-a4a0-b20f5c8ae1c2") + (net "/Power_Charger/CHG_VSET") + (uuid "0795a2d6-ea85-411d-898b-0dc4d3e3af8d") ) (segment - (start 140.7233 104.8996) - (end 144.1927 108.369) + (start 125.784314 99.25) + (end 127.25 97.784314) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "0554d207-08be-4450-960f-d01145e83da4") + (net "/Power_Charger/CHG_VSET") + (uuid "40e50fb6-a670-4756-b683-b0129990d6ee") ) (segment - (start 148.3893 109.2743) - (end 148.3893 110.6746) + (start 125.284314 99.75) + (end 122.28 99.75) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "1d72feff-0c0d-4c85-8802-15a00cf24117") + (net "/Power_Charger/CHG_VSET") + (uuid "442097af-db17-4af3-aa01-7d2a702c2d70") ) (segment - (start 147.484 108.369) - (end 148.3893 109.2743) + (start 127.15 96.854756) + (end 127.354756 96.65) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "6439ab44-8aa9-4e0c-8810-7afd280f21c1") + (net "/Power_Charger/CHG_VSET") + (uuid "4a2b96d6-764b-481a-b412-5cde771837c6") ) (segment - (start 148.3893 110.6746) - (end 146.935 112.1289) + (start 127.354756 96.65) + (end 127.7 96.65) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "6b5d0b97-7a63-46b6-852d-9e3e46c0ae7e") + (net "/Power_Charger/CHG_VSET") + (uuid "96fca300-2d6a-4243-a22e-1302db840510") ) (segment - (start 144.1927 108.369) - (end 147.484 108.369) + (start 127.15 97.245244) + (end 127.15 96.854756) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "a9b32eaf-d743-40e4-8dd6-d49432f980d7") + (net "/Power_Charger/CHG_VSET") + (uuid "987abe9b-f8fd-476c-a54b-70d182e7259d") ) (segment - (start 146.935 112.1289) - (end 146.935 112.235) + (start 127.25 97.345244) + (end 127.15 97.245244) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "bde3f4cd-6d73-4c01-aa5e-7b71d6d25e3b") + (net "/Power_Charger/CHG_VSET") + (uuid "9c55590d-9537-4b61-87a1-38453bbb5713") ) (segment - (start 140.7233 100.4) - (end 140.7233 104.8996) + (start 127.25 97.784314) + (end 127.25 97.345244) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "f0b7d52f-a1fa-4bf5-aa55-b76eb2aef64c") + (net "/Power_Charger/CHG_VSET") + (uuid "da9e6ae3-b4f2-489c-948b-0f630d427ccb") ) (segment - (start 141.65 100.4) - (end 140.7233 100.4) + (start 127.189071 96.25) + (end 127.7 96.25) (width 0.2) (layer "B.Cu") - (net "/MCU_Core/SWDCLK") - (uuid "fecbb44a-dff7-4764-95f2-ace5ff767642") + (net "/Power_Charger/CHG_ISET") + (uuid "528810b9-e7aa-4b5d-806d-1396f879a226") ) (segment - (start 131.1569 92.8547) - (end 129.6056 94.406) + (start 125.618628 98.85) + (end 126.75 97.718628) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "0ad07545-d6a8-4f4a-baef-a029139fb453") + (layer "B.Cu") + (net "/Power_Charger/CHG_ISET") + (uuid "9d73d3fa-beea-4cde-97ea-61b241b2afd8") ) (segment - (start 133.2945 89.5041) - (end 131.1569 91.6417) + (start 126.75 96.68907) + (end 127.189071 96.25) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "3ad3ebdd-9487-49cb-86c7-5a983603d5cf") + (layer "B.Cu") + (net "/Power_Charger/CHG_ISET") + (uuid "ad1f7108-41b9-4de9-9ab5-a12c00559d8f") ) (segment - (start 138.485 72.54) - (end 133.2945 77.7305) + (start 126.75 97.718628) + (end 126.75 96.68907) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "4db68294-3db4-41e3-a4eb-284838f022a2") + (layer "B.Cu") + (net "/Power_Charger/CHG_ISET") + (uuid "b96d4b0b-957d-4052-b977-f0c2456e7bef") ) (segment - (start 133.2945 77.7305) - (end 133.2945 89.5041) + (start 122.3 98.25) + (end 122.9 98.85) (width 0.2) - (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "5f21713e-77cc-4f2e-ab89-887db8a00b5f") + (layer "B.Cu") + (net "/Power_Charger/CHG_ISET") + (uuid "fba091fe-19d7-4616-bc9b-ebaa39f1fad0") ) (segment - (start 131.1569 91.6417) - (end 131.1569 92.8547) + (start 122.9 98.85) + (end 125.618628 98.85) (width 0.2) + (layer "B.Cu") + (net "/Power_Charger/CHG_ISET") + (uuid "fc4f217b-1c16-4ebd-84ee-1d6e99b5668d") + ) + (segment + (start 139.5 97.7) + (end 139.5 94.85) + (width 0.3) (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "7f0d4d6d-9a0c-4b48-b4ca-f3937ba1592f") + (net "/Power_Buck/BUCK_FB") + (uuid "497508bd-9809-4955-bfc7-17a5625e6f9f") ) (segment - (start 129.6056 98.2181) - (end 129.625 98.2375) - (width 0.2) + (start 139.885887 98.085887) + (end 139.5 97.7) + (width 0.3) (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "925fd5bc-2147-4d7b-a5db-2094555b4607") + (net "/Power_Buck/BUCK_FB") + (uuid "6d0e5759-d813-47f9-b463-ce3aac1f76bf") ) (segment - (start 129.6056 94.406) - (end 129.6056 98.2181) - (width 0.2) + (start 139.885887 98.225129) + (end 139.885887 98.085887) + (width 0.3) (layer "F.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "fab93fa0-36fe-4502-ba54-9551658c8e73") + (net "/Power_Buck/BUCK_FB") + (uuid "daffb47d-45b8-444f-b47e-a7980d6f35fd") ) (via - (at 138.485 72.539999) + (at 139.885887 98.225129) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "94dd208b-ecc6-44f0-bb01-41350e5bda07") + (net "/Power_Buck/BUCK_FB") + (uuid "d3882295-903f-496a-8327-367a82e203f8") ) (via - (at 129.625 98.2375) + (at 139.5 94.85) (size 0.6) (drill 0.3) (layers "F.Cu" "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "e38b3673-e7fc-45e2-b30b-12aebb18875c") + (net "/Power_Buck/BUCK_FB") + (uuid "e5e5c8f4-deea-49ec-8894-6047c0cd269a") ) (segment - (start 138.385 72.44) - (end 138.485 72.539999) + (start 139.860758 98.2) + (end 139.835 98.2) (width 0.3) (layer "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "2f23455a-c0eb-4241-a944-6f365355b51d") + (net "/Power_Buck/BUCK_FB") + (uuid "076505ae-38c1-4c2e-9b61-f2fd905efac5") ) (segment - (start 129.625 98.2375) - (end 130.9625 98.2375) - (width 0.2) + (start 148.324795 88.6) + (end 148.562397 88.837603) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "5dc68672-59f3-4aec-b3ff-de366aaa81b8") + (net "/Power_Buck/BUCK_FB") + (uuid "2b7af923-9bc1-4861-9aed-04c0fb443ea3") ) (segment - (start 130.9625 98.2375) - (end 131.025 98.3) - (width 0.2) + (start 139.885887 98.225129) + (end 139.860758 98.2) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "8e1e3754-eb1b-4f36-b9df-410641f42170") + (net "/Power_Buck/BUCK_FB") + (uuid "60e139ce-ce49-42b5-89a3-83cc1c71d8ff") ) (segment - (start 136.935 72.44) - (end 138.385 72.44) + (start 143.4 87.3) + (end 146.8 87.3) (width 0.3) (layer "B.Cu") - (net "/MCU_Core/PWR_HOLD") - (uuid "b5963bcf-eadc-4fa2-b6e9-aaac1b13e8a4") + (net "/Power_Buck/BUCK_FB") + (uuid "614d1fc2-2daa-4e33-8912-e7f7eda2d32e") ) (segment - (start 133.15 95.1) - (end 133.15 94.45) - (width 0.2) + (start 140.3 92.2) + (end 140.3 90.4) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "050ad005-a8bb-4589-bcc2-ac6e79b16ef5") + (net "/Power_Buck/BUCK_FB") + (uuid "653214aa-3350-4805-bf9b-6f92937a8694") ) (segment - (start 132.65 95.75) - (end 132.65 95.65) - (width 0.2) + (start 148.425 88.975) + (end 148.425 93.475) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "05eb1b69-720b-4194-9548-d8f68d6cabb6") + (net "/Power_Buck/BUCK_FB") + (uuid "6c2f9b1a-2bf9-46fe-803e-26eb5686a4bc") ) (segment - (start 133.1 95.15) - (end 133.15 95.1) - (width 0.2) + (start 139.6 93.5) + (end 139.6 92.9) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "11b9b3e5-ad25-4ec2-9b2a-a48fad034725") + (net "/Power_Buck/BUCK_FB") + (uuid "7fa4d0c1-3297-411e-b4cd-5113e876a490") ) (segment - (start 132.525 95.875) - (end 132.525 95.9) - (width 0.2) + (start 140.3 90.4) + (end 143.4 87.3) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "1a52e1c2-e36b-417b-b159-c0a016652677") + (net "/Power_Buck/BUCK_FB") + (uuid "85677582-f187-43f1-bcba-f8a6fbddca84") ) (segment - (start 135.515 91.615) - (end 134.285 91.615) - (width 0.2) + (start 139.5 93.6) + (end 139.6 93.5) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "4db32cae-35b5-4359-8742-fe4d58c03f84") + (net "/Power_Buck/BUCK_FB") + (uuid "9612f31e-d448-4efe-83a5-12a62dadfb61") ) (segment - (start 134.285 91.665) - (end 134.285 91.615) - (width 0.2) + (start 139.5 94.85) + (end 139.5 93.6) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "6cbdacc2-2f9d-4cd0-bac0-0d6ee093e7b5") + (net "/Power_Buck/BUCK_FB") + (uuid "9a4ecee2-336c-46d4-9caa-c41f8939eacd") ) (segment - (start 134.25 91.7) - (end 134.285 91.665) - (width 0.2) + (start 139.6 92.9) + (end 140.3 92.2) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "7993299c-9b5e-4cd7-9237-92abc6d52017") + (net "/Power_Buck/BUCK_FB") + (uuid "9c11eade-d422-4241-8a2f-f2f91e0ecfaf") ) (segment - (start 133.1 95.2) - (end 133.1 95.15) - (width 0.2) + (start 138.525 100.49) + (end 138.525 99.51) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "90042bd8-f007-46e4-aa8e-08186d922f47") + (net "/Power_Buck/BUCK_FB") + (uuid "b478f737-caa2-4237-9260-f6e4e3853361") ) (segment - (start 133.15 94.45) - (end 133.35 94.25) - (width 0.2) + (start 148.1 88.6) + (end 148.324795 88.6) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "b43f2059-f9a0-4358-845f-f231d37a68e7") + (net "/Power_Buck/BUCK_FB") + (uuid "b991062e-e427-4298-8c83-b1289cde2a19") ) (segment - (start 133.35 92.6) - (end 134.25 91.7) - (width 0.2) + (start 148.562397 88.837603) + (end 148.425 88.975) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "dac92f92-d07a-47a9-88c1-10907f9e60a5") + (net "/Power_Buck/BUCK_FB") + (uuid "bb036fb7-5806-4730-b9f2-97f60cb3b74a") ) (segment - (start 132.65 95.65) - (end 133.1 95.2) - (width 0.2) + (start 146.8 87.3) + (end 148.1 88.6) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "dc2c3b60-458f-42b1-8e17-df18cb577327") + (net "/Power_Buck/BUCK_FB") + (uuid "bea8d189-1bcb-4654-88c2-1e1f5dbc2cbb") ) (segment - (start 133.35 94.25) - (end 133.35 92.6) - (width 0.2) + (start 139.835 98.2) + (end 138.525 99.51) + (width 0.3) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "e0ad478e-0834-4f2c-b581-1b3e75b28ca0") + (net "/Power_Buck/BUCK_FB") + (uuid "e90bb634-5bf6-4bc5-a224-87f8acf228dd") ) (segment - (start 132.5 95.9) - (end 132.65 95.75) - (width 0.2) + (start 146.525 95.75) + (end 144.05 95.75) + (width 0.8) (layer "B.Cu") - (net "/MCU_Core/VSYS_SENSE") - (uuid "fa80d3ed-7762-48e9-9db0-741239dc5032") + (net "/Power_Buck/BUCK_SW") + (uuid "1d7c4a5c-a5a1-4a75-bef9-ad120e1983cb") ) (segment - (start 127.2607 66.8523) - (end 126.6925 67.4205) + (start 129.75 88.400648) + (end 129.75 90.74) (width 0.2) - (layer "F.Cu") + (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "ccdc7027-8ef7-4951-97c6-a3b7419c2b92") + (uuid "4224e89d-87e9-4f28-804a-bf29daa5555b") ) (segment - (start 126.6925 67.4205) - (end 126.6925 80.6287) + (start 127.1 82.847613) + (end 127.1 84.152387) (width 0.2) - (layer "F.Cu") - (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "d945f0e7-e669-4e16-9e0a-f37bf0bb78d8") - ) - (via - (at 127.2607 66.8523) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") + (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "38fe30ba-7b13-4f59-97dc-2b1586881705") + (uuid "4b14e851-55f5-4ce9-bd9a-97583c014042") ) - (via - (at 126.6925 80.6287) - (size 0.6) - (drill 0.3) - (layers "F.Cu" "B.Cu") + (segment + (start 127.6 74.652387) + (end 127.6 82.347613) + (width 0.2) + (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "7f3e5b7d-47ea-4bd1-b17e-0bba85c4cef2") + (uuid "56f3a368-240f-4a0f-9453-bb0e6f5cc586") ) (segment - (start 130.2517 85.1699) - (end 133.1825 88.1007) + (start 127.1 74.152387) + (end 127.6 74.652387) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "041d756c-f6fc-49dc-b9fc-3fbe30da4711") + (uuid "6a1f04fc-7edf-4349-978c-aa21a49e0907") ) (segment - (start 130.2517 82.8142) - (end 130.2517 85.1699) + (start 127.4375 68.3875) + (end 127.4375 65.7) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "1ac7e236-62ed-42b9-ba51-4033558a09a4") + (uuid "807e8959-2130-48d9-b0b3-4fb45633d4f9") ) (segment - (start 132.0707 90.4555) - (end 130.0345 90.4555) + (start 127.6 84.652387) + (end 127.6 86.250648) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "2c87e91a-711d-4da5-832f-b5fa51303a86") + (uuid "a30b1fed-230b-466c-88e3-1ca34c4ac652") ) (segment - (start 130.0345 90.4555) - (end 129.75 90.74) + (start 127.6 86.250648) + (end 129.75 88.400648) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "62ba0e71-823f-45ec-a228-b3ec16653a90") + (uuid "b1fa2919-ab21-4653-b04b-216730011794") ) (segment - (start 133.1825 89.3437) - (end 132.0707 90.4555) + (start 127.6 72.347613) + (end 127.1 72.847613) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "6e44c510-bf0e-4020-904d-b2f2f126d41a") + (uuid "b414a18a-75a1-46b0-b974-fb6afacd8231") ) (segment - (start 128.0662 80.6287) - (end 130.2517 82.8142) + (start 127.1 72.847613) + (end 127.1 74.152387) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "e8872b96-3648-4d68-a4a4-f48e78cedd7d") + (uuid "b4f98c74-f636-40d3-8781-cbb2fe621db9") ) (segment - (start 133.1825 88.1007) - (end 133.1825 89.3437) + (start 127.6 68.55) + (end 127.6 72.347613) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "ec995753-b768-475c-a5fb-34c6866ca741") + (uuid "b7736e84-1c17-4102-a597-d8814744f5dd") ) (segment - (start 127.2607 66.4143) - (end 127.2607 66.8523) + (start 127.6 82.347613) + (end 127.1 82.847613) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "f3715279-d338-4c21-bba3-40a8d8071323") + (uuid "bedd60b9-be1a-4506-9898-3779007cc11b") ) (segment - (start 126.6925 80.6287) - (end 128.0662 80.6287) + (start 127.6 68.55) + (end 127.4375 68.3875) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "fd8c3f44-6345-4eae-b22f-a04f54fb6f66") + (uuid "eaaf9908-93da-4527-b8db-a6c338b48f88") ) (segment - (start 127.625 66.05) - (end 127.2607 66.4143) + (start 127.1 84.152387) + (end 127.6 84.652387) (width 0.2) (layer "B.Cu") (net "/Hall_Trigger/TRIG_ANALOG") - (uuid "fefa266c-5a98-4f60-b525-8dc64b58d9d5") + (uuid "f43d6136-aa8b-4085-8577-ee15e63c8be5") ) (zone (net "3V3") @@ -37194,10 +36635,7 @@ (filled_polygon (layer "In1.Cu") (pts - (xy 148.840836 97.311739) (xy 148.934509 97.350539) (xy 148.985203 97.371537) (xy 149.121373 97.398623) - (xy 149.139853 97.402299) (xy 149.139856 97.4023) (xy 149.139858 97.4023) (xy 149.297544 97.4023) - (xy 149.297545 97.402299) (xy 149.452197 97.371537) (xy 149.578049 97.319407) (xy 149.647517 97.311939) - (xy 149.709996 97.343214) (xy 149.745648 97.403303) (xy 149.7495 97.433969) (xy 149.7495 129.6255) + (xy 149.692539 60.270185) (xy 149.738294 60.322989) (xy 149.7495 60.3745) (xy 149.7495 129.6255) (xy 149.729815 129.692539) (xy 149.677011 129.738294) (xy 149.6255 129.7495) (xy 120.3745 129.7495) (xy 120.307461 129.729815) (xy 120.261706 129.677011) (xy 120.2505 129.6255) (xy 120.2505 128.557194) (xy 120.270185 128.490155) (xy 120.322989 128.4444) (xy 120.392147 128.434456) (xy 120.443391 128.454092) @@ -37224,889 +36662,1822 @@ (xy 141.221459 129.5005) (xy 141.418543 129.5005) (xy 141.548582 129.474632) (xy 141.611835 129.462051) (xy 141.793914 129.386632) (xy 141.957782 129.277139) (xy 142.097139 129.137782) (xy 142.206632 128.973914) (xy 142.282051 128.791835) (xy 142.294632 128.728582) (xy 142.3205 128.598543) (xy 142.3205 127.801456) - (xy 142.282052 127.60817) (xy 142.282051 127.608169) (xy 142.282051 127.608165) (xy 142.26549 127.568182) - (xy 142.214264 127.44451) (xy 142.206795 127.375041) (xy 142.23807 127.312562) (xy 142.29816 127.27691) - (xy 142.367985 127.279404) (xy 142.397714 127.293954) (xy 142.420821 127.309394) (xy 142.420823 127.309395) - (xy 142.420827 127.309397) (xy 142.514749 127.3483) (xy 142.566503 127.369737) (xy 142.721153 127.400499) - (xy 142.721156 127.4005) (xy 142.721158 127.4005) (xy 142.878844 127.4005) (xy 142.878845 127.400499) - (xy 143.033497 127.369737) (xy 143.179179 127.309394) (xy 143.310289 127.221789) (xy 143.421789 127.110289) - (xy 143.509394 126.979179) (xy 143.526472 126.93795) (xy 143.544795 126.893713) (xy 145.6495 126.893713) - (xy 145.6495 127.106287) (xy 145.659534 127.169644) (xy 145.681669 127.309397) (xy 145.682754 127.316243) - (xy 145.718446 127.426092) (xy 145.748444 127.518414) (xy 145.844951 127.70782) (xy 145.96989 127.879786) - (xy 146.120213 128.030109) (xy 146.292179 128.155048) (xy 146.292181 128.155049) (xy 146.292184 128.155051) - (xy 146.481588 128.251557) (xy 146.683757 128.317246) (xy 146.893713 128.3505) (xy 146.893714 128.3505) - (xy 147.106286 128.3505) (xy 147.106287 128.3505) (xy 147.316243 128.317246) (xy 147.518412 128.251557) - (xy 147.707816 128.155051) (xy 147.777639 128.104322) (xy 147.879786 128.030109) (xy 147.879788 128.030106) - (xy 147.879792 128.030104) (xy 148.030104 127.879792) (xy 148.030106 127.879788) (xy 148.030109 127.879786) - (xy 148.155048 127.70782) (xy 148.155047 127.70782) (xy 148.155051 127.707816) (xy 148.251557 127.518412) - (xy 148.317246 127.316243) (xy 148.3505 127.106287) (xy 148.3505 126.893713) (xy 148.317246 126.683757) - (xy 148.251557 126.481588) (xy 148.155051 126.292184) (xy 148.155049 126.292181) (xy 148.155048 126.292179) - (xy 148.030109 126.120213) (xy 147.879786 125.96989) (xy 147.70782 125.844951) (xy 147.518414 125.748444) - (xy 147.518413 125.748443) (xy 147.518412 125.748443) (xy 147.316243 125.682754) (xy 147.316241 125.682753) - (xy 147.31624 125.682753) (xy 147.154957 125.657208) (xy 147.106287 125.6495) (xy 146.893713 125.6495) - (xy 146.845042 125.657208) (xy 146.68376 125.682753) (xy 146.481585 125.748444) (xy 146.292179 125.844951) - (xy 146.120213 125.96989) (xy 145.96989 126.120213) (xy 145.844951 126.292179) (xy 145.748444 126.481585) - (xy 145.748443 126.481587) (xy 145.748443 126.481588) (xy 145.735587 126.521155) (xy 145.682753 126.68376) - (xy 145.6495 126.893713) (xy 143.544795 126.893713) (xy 143.566468 126.841389) (xy 143.566468 126.841388) - (xy 143.566469 126.841386) (xy 143.569737 126.833497) (xy 143.6005 126.678842) (xy 143.6005 126.521158) - (xy 143.6005 126.521155) (xy 143.600499 126.521153) (xy 143.583838 126.437392) (xy 143.569737 126.366503) - (xy 143.569735 126.366498) (xy 143.509397 126.220827) (xy 143.50939 126.220814) (xy 143.421789 126.089711) - (xy 143.421786 126.089707) (xy 143.310292 125.978213) (xy 143.310288 125.97821) (xy 143.179185 125.890609) - (xy 143.179172 125.890602) (xy 143.033501 125.830264) (xy 143.033489 125.830261) (xy 142.878845 125.7995) - (xy 142.878842 125.7995) (xy 142.721158 125.7995) (xy 142.721155 125.7995) (xy 142.56651 125.830261) - (xy 142.566498 125.830264) (xy 142.420827 125.890602) (xy 142.420814 125.890609) (xy 142.289711 125.97821) - (xy 142.289707 125.978213) (xy 142.178213 126.089707) (xy 142.17821 126.089711) (xy 142.090609 126.220814) - (xy 142.090602 126.220827) (xy 142.030264 126.366498) (xy 142.030261 126.36651) (xy 141.9995 126.521153) - (xy 141.9995 126.678846) (xy 142.030261 126.833489) (xy 142.030264 126.833501) (xy 142.067295 126.922902) - (xy 142.074764 126.992371) (xy 142.043489 127.05485) (xy 141.983399 127.090502) (xy 141.913574 127.088008) - (xy 141.883843 127.073456) (xy 141.79392 127.013371) (xy 141.793907 127.013364) (xy 141.611839 126.93795) - (xy 141.611829 126.937947) (xy 141.418543 126.8995) (xy 141.418541 126.8995) (xy 141.221459 126.8995) - (xy 141.221457 126.8995) (xy 141.02817 126.937947) (xy 141.02816 126.93795) (xy 140.846092 127.013364) - (xy 140.846079 127.013371) (xy 140.682218 127.12286) (xy 140.682214 127.122863) (xy 140.542863 127.262214) - (xy 140.54286 127.262218) (xy 140.433371 127.426079) (xy 140.433364 127.426092) (xy 140.35795 127.60816) - (xy 140.357947 127.60817) (xy 140.3195 127.801456) (xy 140.3195 127.801459) (xy 140.3195 128.598541) - (xy 140.3195 128.598543) (xy 140.319499 128.598543) (xy 133.6805 128.598543) (xy 133.6805 127.801456) - (xy 133.642052 127.60817) (xy 133.642051 127.608169) (xy 133.642051 127.608165) (xy 133.604875 127.518414) - (xy 133.566635 127.426092) (xy 133.566628 127.426079) (xy 133.457139 127.262218) (xy 133.457136 127.262214) - (xy 133.317785 127.122863) (xy 133.317781 127.12286) (xy 133.15392 127.013371) (xy 133.153907 127.013364) - (xy 132.971839 126.93795) (xy 132.971829 126.937947) (xy 132.778543 126.8995) (xy 132.778541 126.8995) - (xy 132.581459 126.8995) (xy 132.581457 126.8995) (xy 132.38817 126.937947) (xy 132.38816 126.93795) - (xy 132.206092 127.013364) (xy 132.206079 127.013371) (xy 132.042218 127.12286) (xy 132.042214 127.122863) - (xy 131.902863 127.262214) (xy 131.90286 127.262218) (xy 131.793371 127.426079) (xy 131.793364 127.426092) - (xy 131.71795 127.60816) (xy 131.717947 127.60817) (xy 131.6795 127.801456) (xy 131.6795 127.801459) - (xy 131.6795 128.598541) (xy 131.6795 128.598543) (xy 131.679499 128.598543) (xy 125.203833 128.598543) - (xy 125.285041 128.582389) (xy 125.329328 128.57358) (xy 125.456811 128.520775) (xy 125.571542 128.444114) - (xy 125.669114 128.346542) (xy 125.745775 128.231811) (xy 125.79858 128.104328) (xy 125.8255 127.968993) - (xy 125.8255 127.831007) (xy 125.819622 127.801459) (xy 125.800996 127.70782) (xy 125.79858 127.695672) - (xy 125.762334 127.608165) (xy 125.745778 127.568195) (xy 125.745771 127.568182) (xy 125.669114 127.453458) - (xy 125.669111 127.453454) (xy 125.571545 127.355888) (xy 125.571541 127.355885) (xy 125.456817 127.279228) - (xy 125.456804 127.279221) (xy 125.329332 127.226421) (xy 125.329322 127.226418) (xy 125.193995 127.1995) - (xy 125.193993 127.1995) (xy 125.056007 127.1995) (xy 125.056005 127.1995) (xy 124.920677 127.226418) - (xy 124.920667 127.226421) (xy 124.793195 127.279221) (xy 124.793182 127.279228) (xy 124.678458 127.355885) - (xy 124.678454 127.355888) (xy 124.580888 127.453454) (xy 124.580885 127.453458) (xy 124.504228 127.568182) - (xy 124.504221 127.568195) (xy 124.451421 127.695667) (xy 124.451418 127.695677) (xy 124.4245 127.831004) - (xy 124.4245 127.831007) (xy 124.4245 127.968993) (xy 124.4245 127.968995) (xy 124.424499 127.968995) - (xy 121.5755 127.968995) (xy 121.5755 127.968993) (xy 121.5755 127.831007) (xy 121.5755 127.831004) - (xy 121.548581 127.695677) (xy 121.54858 127.695676) (xy 121.54858 127.695672) (xy 121.512334 127.608165) - (xy 121.495778 127.568195) (xy 121.495771 127.568182) (xy 121.419114 127.453458) (xy 121.419111 127.453454) - (xy 121.321545 127.355888) (xy 121.321541 127.355885) (xy 121.206817 127.279228) (xy 121.206804 127.279221) - (xy 121.079332 127.226421) (xy 121.079322 127.226418) (xy 120.943995 127.1995) (xy 120.943993 127.1995) - (xy 120.806007 127.1995) (xy 120.806005 127.1995) (xy 120.670677 127.226418) (xy 120.670667 127.226421) - (xy 120.543195 127.279221) (xy 120.543182 127.279228) (xy 120.443391 127.345907) (xy 120.376713 127.366785) - (xy 120.309333 127.3483) (xy 120.262643 127.296321) (xy 120.2505 127.242805) (xy 120.2505 122.393713) - (xy 121.6495 122.393713) (xy 121.6495 122.606287) (xy 121.682754 122.816243) (xy 121.739204 122.989978) - (xy 121.748444 123.018414) (xy 121.844951 123.20782) (xy 121.96989 123.379786) (xy 122.120213 123.530109) - (xy 122.292182 123.65505) (xy 122.329652 123.674142) (xy 122.380449 123.722116) (xy 122.397244 123.789937) - (xy 122.374707 123.856072) (xy 122.320811 123.899188) (xy 122.220824 123.940604) (xy 122.220814 123.940609) - (xy 122.089711 124.02821) (xy 122.089707 124.028213) (xy 121.978213 124.139707) (xy 121.97821 124.139711) - (xy 121.890609 124.270814) (xy 121.890602 124.270827) (xy 121.830264 124.416498) (xy 121.830261 124.41651) - (xy 121.7995 124.571153) (xy 121.7995 124.728846) (xy 121.830261 124.883489) (xy 121.830264 124.883501) - (xy 121.890602 125.029172) (xy 121.890609 125.029185) (xy 121.958713 125.131109) (xy 121.979591 125.197787) - (xy 121.961107 125.265167) (xy 121.958713 125.268891) (xy 121.890609 125.370814) (xy 121.890602 125.370827) - (xy 121.830264 125.516498) (xy 121.830261 125.51651) (xy 121.7995 125.671153) (xy 121.7995 125.828846) - (xy 121.830261 125.983489) (xy 121.830264 125.983501) (xy 121.890602 126.129172) (xy 121.890609 126.129185) - (xy 121.97821 126.260288) (xy 121.978213 126.260292) (xy 122.089707 126.371786) (xy 122.089711 126.371789) - (xy 122.220814 126.45939) (xy 122.220827 126.459397) (xy 122.366498 126.519735) (xy 122.366503 126.519737) - (xy 122.521153 126.550499) (xy 122.521156 126.5505) (xy 122.521158 126.5505) (xy 122.678844 126.5505) - (xy 122.678845 126.550499) (xy 122.833497 126.519737) (xy 122.979179 126.459394) (xy 123.110289 126.371789) - (xy 123.221789 126.260289) (xy 123.309394 126.129179) (xy 123.369737 125.983497) (xy 123.4005 125.828842) - (xy 123.4005 125.671158) (xy 123.4005 125.671155) (xy 123.400499 125.671153) (xy 123.38717 125.604146) - (xy 123.369737 125.516503) (xy 123.340722 125.446453) (xy 124.9695 125.446453) (xy 124.9695 125.604146) - (xy 125.000261 125.758789) (xy 125.000264 125.758801) (xy 125.060602 125.904472) (xy 125.060609 125.904485) - (xy 125.14821 126.035588) (xy 125.148213 126.035592) (xy 125.259707 126.147086) (xy 125.259711 126.147089) - (xy 125.390814 126.23469) (xy 125.390827 126.234697) (xy 125.529603 126.292179) (xy 125.536503 126.295037) - (xy 125.691153 126.325799) (xy 125.691156 126.3258) (xy 125.691158 126.3258) (xy 125.848844 126.3258) - (xy 125.848845 126.325799) (xy 126.003497 126.295037) (xy 126.149179 126.234694) (xy 126.169445 126.221153) - (xy 129.5995 126.221153) (xy 129.5995 126.378846) (xy 129.630261 126.533489) (xy 129.630264 126.533501) - (xy 129.690602 126.679172) (xy 129.690609 126.679185) (xy 129.77821 126.810288) (xy 129.778213 126.810292) - (xy 129.889707 126.921786) (xy 129.889711 126.921789) (xy 130.020814 127.00939) (xy 130.020827 127.009397) - (xy 130.130562 127.05485) (xy 130.166503 127.069737) (xy 130.321153 127.100499) (xy 130.321156 127.1005) - (xy 130.321158 127.1005) (xy 130.478844 127.1005) (xy 130.478845 127.100499) (xy 130.633497 127.069737) - (xy 130.769585 127.013368) (xy 130.779172 127.009397) (xy 130.779172 127.009396) (xy 130.779179 127.009394) - (xy 130.910289 126.921789) (xy 131.021789 126.810289) (xy 131.109394 126.679179) (xy 131.169737 126.533497) - (xy 131.2005 126.378842) (xy 131.2005 126.221158) (xy 131.2005 126.221155) (xy 131.200499 126.221153) - (xy 131.192148 126.179172) (xy 131.169737 126.066503) (xy 131.169735 126.066498) (xy 131.109397 125.920827) - (xy 131.10939 125.920814) (xy 131.02179 125.789712) (xy 131.021784 125.789705) (xy 130.953232 125.721153) - (xy 136.5995 125.721153) (xy 136.5995 125.878846) (xy 136.630261 126.033489) (xy 136.630264 126.033501) - (xy 136.690602 126.179172) (xy 136.690609 126.179185) (xy 136.77821 126.310288) (xy 136.778213 126.310292) - (xy 136.889707 126.421786) (xy 136.889711 126.421789) (xy 137.020814 126.50939) (xy 137.020827 126.509397) - (xy 137.12006 126.5505) (xy 137.166503 126.569737) (xy 137.321153 126.600499) (xy 137.321156 126.6005) - (xy 137.321158 126.6005) (xy 137.478844 126.6005) (xy 137.478845 126.600499) (xy 137.633497 126.569737) - (xy 137.779179 126.509394) (xy 137.886937 126.437391) (xy 137.953614 126.416514) (xy 138.020994 126.434998) - (xy 138.05893 126.471603) (xy 138.12821 126.575289) (xy 138.239707 126.686786) (xy 138.239711 126.686789) - (xy 138.370814 126.77439) (xy 138.370827 126.774397) (xy 138.51349 126.833489) (xy 138.516503 126.834737) - (xy 138.671153 126.865499) (xy 138.671156 126.8655) (xy 138.671158 126.8655) (xy 138.828844 126.8655) - (xy 138.828845 126.865499) (xy 138.983497 126.834737) (xy 139.129179 126.774394) (xy 139.260289 126.686789) - (xy 139.371789 126.575289) (xy 139.459394 126.444179) (xy 139.519737 126.298497) (xy 139.5505 126.143842) - (xy 139.5505 125.986158) (xy 139.5505 125.986155) (xy 139.550499 125.986153) (xy 139.537505 125.920827) - (xy 139.519737 125.831503) (xy 139.519223 125.830261) (xy 139.459397 125.685827) (xy 139.45939 125.685814) - (xy 139.371789 125.554711) (xy 139.371786 125.554707) (xy 139.260292 125.443213) (xy 139.260288 125.44321) - (xy 139.129185 125.355609) (xy 139.129172 125.355602) (xy 138.983501 125.295264) (xy 138.983489 125.295261) - (xy 138.828845 125.2645) (xy 138.828842 125.2645) (xy 138.671158 125.2645) (xy 138.671155 125.2645) - (xy 138.51651 125.295261) (xy 138.516498 125.295264) (xy 138.370827 125.355602) (xy 138.370809 125.355612) - (xy 138.263061 125.427607) (xy 138.196384 125.448485) (xy 138.129004 125.43) (xy 138.091069 125.393395) - (xy 138.021792 125.289715) (xy 138.021786 125.289707) (xy 137.910292 125.178213) (xy 137.910288 125.17821) - (xy 137.779185 125.090609) (xy 137.779172 125.090602) (xy 137.633501 125.030264) (xy 137.633489 125.030261) - (xy 137.478845 124.9995) (xy 137.478842 124.9995) (xy 137.321158 124.9995) (xy 137.321155 124.9995) - (xy 137.16651 125.030261) (xy 137.166498 125.030264) (xy 137.020827 125.090602) (xy 137.020814 125.090609) - (xy 136.889711 125.17821) (xy 136.889707 125.178213) (xy 136.778213 125.289707) (xy 136.77821 125.289711) - (xy 136.690609 125.420814) (xy 136.690602 125.420827) (xy 136.630264 125.566498) (xy 136.630261 125.56651) - (xy 136.5995 125.721153) (xy 130.953232 125.721153) (xy 130.910292 125.678213) (xy 130.910288 125.67821) - (xy 130.779185 125.590609) (xy 130.779172 125.590602) (xy 130.633501 125.530264) (xy 130.633489 125.530261) - (xy 130.478845 125.4995) (xy 130.478842 125.4995) (xy 130.321158 125.4995) (xy 130.321155 125.4995) - (xy 130.16651 125.530261) (xy 130.166498 125.530264) (xy 130.020827 125.590602) (xy 130.020814 125.590609) - (xy 129.889711 125.67821) (xy 129.889707 125.678213) (xy 129.778213 125.789707) (xy 129.77821 125.789711) - (xy 129.690609 125.920814) (xy 129.690602 125.920827) (xy 129.630264 126.066498) (xy 129.630261 126.06651) - (xy 129.5995 126.221153) (xy 126.169445 126.221153) (xy 126.280289 126.147089) (xy 126.283536 126.143842) - (xy 126.299994 126.127385) (xy 126.391786 126.035592) (xy 126.391789 126.035589) (xy 126.479394 125.904479) - (xy 126.479395 125.904476) (xy 126.479397 125.904473) (xy 126.526934 125.789707) (xy 126.539192 125.76011) - (xy 126.566069 125.719886) (xy 127.78232 124.503636) (xy 127.843639 124.470154) (xy 127.913331 124.475138) - (xy 127.969264 124.51701) (xy 127.984558 124.543867) (xy 128.040604 124.679176) (xy 128.040609 124.679185) - (xy 128.12821 124.810288) (xy 128.128213 124.810292) (xy 128.239707 124.921786) (xy 128.239711 124.921789) - (xy 128.370814 125.00939) (xy 128.370827 125.009397) (xy 128.516498 125.069735) (xy 128.516503 125.069737) - (xy 128.671153 125.100499) (xy 128.671156 125.1005) (xy 128.671158 125.1005) (xy 128.828844 125.1005) - (xy 128.828845 125.100499) (xy 128.983497 125.069737) (xy 129.129179 125.009394) (xy 129.260289 124.921789) - (xy 129.371789 124.810289) (xy 129.459394 124.679179) (xy 129.519737 124.533497) (xy 129.5505 124.378842) - (xy 129.5505 124.221158) (xy 129.5505 124.221155) (xy 129.550499 124.221153) (xy 129.529684 124.11651) - (xy 129.519737 124.066503) (xy 129.492776 124.001414) (xy 129.485308 123.931948) (xy 129.516583 123.869469) - (xy 129.559886 123.839403) (xy 129.595873 123.824497) (xy 129.595876 123.824495) (xy 129.595879 123.824494) - (xy 129.726989 123.736889) (xy 129.838489 123.625389) (xy 129.926094 123.494279) (xy 129.986437 123.348597) - (xy 130.0172 123.193942) (xy 130.0172 123.036258) (xy 130.0172 123.036255) (xy 130.017199 123.036253) - (xy 130.00809 122.990458) (xy 129.986437 122.881603) (xy 129.930606 122.746814) (xy 129.926097 122.735927) - (xy 129.92609 122.735914) (xy 129.835105 122.599746) (xy 129.836205 122.59901) (xy 129.811549 122.540953) - (xy 129.823342 122.472086) (xy 129.847029 122.438926) (xy 130.100839 122.185116) (xy 130.162161 122.151634) - (xy 130.188519 122.1488) (xy 132.281813 122.1488) (xy 132.348852 122.168485) (xy 132.394607 122.221289) - (xy 132.40343 122.248609) (xy 132.430074 122.382557) (xy 132.423847 122.452148) (xy 132.380984 122.507326) - (xy 132.35591 122.521309) (xy 132.206088 122.583366) (xy 132.206079 122.583371) (xy 132.042218 122.69286) - (xy 132.042214 122.692863) (xy 131.902863 122.832214) (xy 131.90286 122.832218) (xy 131.793371 122.996079) - (xy 131.793364 122.996092) (xy 131.71795 123.17816) (xy 131.717947 123.17817) (xy 131.6795 123.371456) - (xy 131.6795 123.456022) (xy 131.659815 123.523061) (xy 131.607011 123.568816) (xy 131.579693 123.577639) - (xy 131.566507 123.580261) (xy 131.566498 123.580264) (xy 131.420827 123.640602) (xy 131.420814 123.640609) - (xy 131.289711 123.72821) (xy 131.289707 123.728213) (xy 131.178213 123.839707) (xy 131.17821 123.839711) - (xy 131.090609 123.970814) (xy 131.090602 123.970827) (xy 131.030264 124.116498) (xy 131.030261 124.11651) - (xy 130.9995 124.271153) (xy 130.9995 124.428846) (xy 131.030261 124.583489) (xy 131.030264 124.583501) - (xy 131.090602 124.729172) (xy 131.090609 124.729185) (xy 131.17821 124.860288) (xy 131.178213 124.860292) - (xy 131.289707 124.971786) (xy 131.289711 124.971789) (xy 131.420814 125.05939) (xy 131.420827 125.059397) - (xy 131.52006 125.1005) (xy 131.566503 125.119737) (xy 131.699174 125.146127) (xy 131.721153 125.150499) - (xy 131.721156 125.1505) (xy 131.721158 125.1505) (xy 131.798307 125.1505) (xy 131.865346 125.170185) - (xy 131.898904 125.203149) (xy 131.898997 125.203074) (xy 131.899702 125.203933) (xy 131.901411 125.205612) - (xy 131.902861 125.207783) (xy 132.042214 125.347136) (xy 132.042218 125.347139) (xy 132.206079 125.456628) - (xy 132.206092 125.456635) (xy 132.383848 125.530263) (xy 132.388165 125.532051) (xy 132.388169 125.532051) - (xy 132.38817 125.532052) (xy 132.581456 125.5705) (xy 132.581459 125.5705) (xy 132.778543 125.5705) - (xy 132.908582 125.544632) (xy 132.971835 125.532051) (xy 133.153914 125.456632) (xy 133.317782 125.347139) - (xy 133.457139 125.207782) (xy 133.566632 125.043914) (xy 133.566631 125.043914) (xy 133.570017 125.038848) - (xy 133.571474 125.039821) (xy 133.614595 124.995903) (xy 133.682729 124.980426) (xy 133.748414 125.004242) - (xy 133.750502 125.005809) (xy 133.756632 125.010512) (xy 133.756635 125.010515) (xy 133.887865 125.086281) - (xy 134.034234 125.1255) (xy 134.034236 125.1255) (xy 134.185764 125.1255) (xy 134.185766 125.1255) - (xy 134.332135 125.086281) (xy 134.463365 125.010515) (xy 134.570515 124.903365) (xy 134.646281 124.772135) - (xy 134.6855 124.625766) (xy 134.6855 124.474234) (xy 134.646281 124.327865) (xy 134.570515 124.196635) - (xy 134.463365 124.089485) (xy 134.385162 124.044334) (xy 134.332136 124.013719) (xy 134.224994 123.985011) - (xy 134.185766 123.9745) (xy 134.034234 123.9745) (xy 133.887862 124.013719) (xy 133.866499 124.026054) - (xy 133.798598 124.042525) (xy 133.732572 124.019673) (xy 133.689382 123.964751) (xy 133.6805 123.918666) - (xy 133.6805 123.371456) (xy 133.642052 123.17817) (xy 133.642051 123.178169) (xy 133.642051 123.178165) - (xy 133.583272 123.036258) (xy 133.564301 122.990457) (xy 133.56676 122.989438) (xy 133.554825 122.932368) - (xy 133.579766 122.867101) (xy 133.60954 122.839106) (xy 133.710288 122.771789) (xy 133.821788 122.660289) - (xy 133.909393 122.529179) (xy 133.96797 122.38776) (xy 134.011808 122.33336) (xy 134.078102 122.311294) - (xy 134.145801 122.328572) (xy 134.15142 122.332113) (xy 134.270814 122.41189) (xy 134.270827 122.411897) - (xy 134.415185 122.471691) (xy 134.455414 122.498571) (xy 134.703653 122.746811) (xy 134.703654 122.746812) - (xy 134.818392 122.823477) (xy 134.945867 122.876278) (xy 134.945872 122.87628) (xy 134.945876 122.87628) - (xy 134.945877 122.876281) (xy 135.081203 122.9032) (xy 135.081206 122.9032) (xy 139.185196 122.9032) - (xy 139.27624 122.885089) (xy 139.320528 122.87628) (xy 139.410282 122.839103) (xy 139.448007 122.823477) - (xy 139.448008 122.823476) (xy 139.448011 122.823475) (xy 139.562743 122.746814) (xy 139.644587 122.664968) - (xy 139.684804 122.638095) (xy 139.829179 122.578294) (xy 139.929499 122.511261) (xy 139.996176 122.490384) - (xy 140.063556 122.508868) (xy 140.101492 122.545473) (xy 140.17821 122.660288) (xy 140.178213 122.660292) - (xy 140.289708 122.771787) (xy 140.289711 122.771789) (xy 140.390457 122.839105) (xy 140.435261 122.892715) - (xy 140.443968 122.96204) (xy 140.43454 122.989978) (xy 140.435699 122.990458) (xy 140.35795 123.17816) + (xy 142.282052 127.60817) (xy 142.282051 127.608169) (xy 142.282051 127.608165) (xy 142.244875 127.518414) + (xy 142.206635 127.426092) (xy 142.206628 127.426079) (xy 142.097139 127.262218) (xy 142.097136 127.262214) + (xy 141.957785 127.122863) (xy 141.957781 127.12286) (xy 141.79392 127.013371) (xy 141.793907 127.013364) + (xy 141.769855 127.003402) (xy 141.611839 126.93795) (xy 141.611829 126.937947) (xy 141.418543 126.8995) + (xy 141.418541 126.8995) (xy 141.221459 126.8995) (xy 141.221457 126.8995) (xy 141.02817 126.937947) + (xy 141.02816 126.93795) (xy 140.846092 127.013364) (xy 140.846079 127.013371) (xy 140.682218 127.12286) + (xy 140.682214 127.122863) (xy 140.542863 127.262214) (xy 140.54286 127.262218) (xy 140.433371 127.426079) + (xy 140.433364 127.426092) (xy 140.35795 127.60816) (xy 140.357947 127.60817) (xy 140.3195 127.801456) + (xy 140.3195 127.801459) (xy 140.3195 128.598541) (xy 140.3195 128.598543) (xy 140.319499 128.598543) + (xy 133.6805 128.598543) (xy 133.6805 127.801456) (xy 133.642052 127.60817) (xy 133.642051 127.608169) + (xy 133.642051 127.608165) (xy 133.604875 127.518414) (xy 133.566635 127.426092) (xy 133.566628 127.426079) + (xy 133.457139 127.262218) (xy 133.457136 127.262214) (xy 133.317785 127.122863) (xy 133.317781 127.12286) + (xy 133.15392 127.013371) (xy 133.153907 127.013364) (xy 132.971839 126.93795) (xy 132.971829 126.937947) + (xy 132.778543 126.8995) (xy 132.778541 126.8995) (xy 132.581459 126.8995) (xy 132.581457 126.8995) + (xy 132.38817 126.937947) (xy 132.38816 126.93795) (xy 132.206092 127.013364) (xy 132.206079 127.013371) + (xy 132.042218 127.12286) (xy 132.042214 127.122863) (xy 131.902863 127.262214) (xy 131.90286 127.262218) + (xy 131.793371 127.426079) (xy 131.793364 127.426092) (xy 131.71795 127.60816) (xy 131.717947 127.60817) + (xy 131.6795 127.801456) (xy 131.6795 127.801459) (xy 131.6795 128.598541) (xy 131.6795 128.598543) + (xy 131.679499 128.598543) (xy 125.203833 128.598543) (xy 125.285041 128.582389) (xy 125.329328 128.57358) + (xy 125.456811 128.520775) (xy 125.571542 128.444114) (xy 125.669114 128.346542) (xy 125.745775 128.231811) + (xy 125.79858 128.104328) (xy 125.8255 127.968993) (xy 125.8255 127.831007) (xy 125.819622 127.801459) + (xy 125.800996 127.70782) (xy 125.79858 127.695672) (xy 125.762334 127.608165) (xy 125.745778 127.568195) + (xy 125.745771 127.568182) (xy 125.669114 127.453458) (xy 125.669111 127.453454) (xy 125.571545 127.355888) + (xy 125.571541 127.355885) (xy 125.456817 127.279228) (xy 125.456804 127.279221) (xy 125.329332 127.226421) + (xy 125.329322 127.226418) (xy 125.193995 127.1995) (xy 125.193993 127.1995) (xy 125.056007 127.1995) + (xy 125.056005 127.1995) (xy 124.920677 127.226418) (xy 124.920667 127.226421) (xy 124.793195 127.279221) + (xy 124.793182 127.279228) (xy 124.678458 127.355885) (xy 124.678454 127.355888) (xy 124.580888 127.453454) + (xy 124.580885 127.453458) (xy 124.504228 127.568182) (xy 124.504221 127.568195) (xy 124.451421 127.695667) + (xy 124.451418 127.695677) (xy 124.4245 127.831004) (xy 124.4245 127.831007) (xy 124.4245 127.968993) + (xy 124.4245 127.968995) (xy 124.424499 127.968995) (xy 121.5755 127.968995) (xy 121.5755 127.968993) + (xy 121.5755 127.831007) (xy 121.5755 127.831004) (xy 121.548581 127.695677) (xy 121.54858 127.695676) + (xy 121.54858 127.695672) (xy 121.512334 127.608165) (xy 121.495778 127.568195) (xy 121.495771 127.568182) + (xy 121.419114 127.453458) (xy 121.419111 127.453454) (xy 121.321545 127.355888) (xy 121.321541 127.355885) + (xy 121.206817 127.279228) (xy 121.206804 127.279221) (xy 121.079332 127.226421) (xy 121.079322 127.226418) + (xy 120.943995 127.1995) (xy 120.943993 127.1995) (xy 120.806007 127.1995) (xy 120.806005 127.1995) + (xy 120.670677 127.226418) (xy 120.670667 127.226421) (xy 120.543195 127.279221) (xy 120.543182 127.279228) + (xy 120.443391 127.345907) (xy 120.376713 127.366785) (xy 120.309333 127.3483) (xy 120.262643 127.296321) + (xy 120.2505 127.242805) (xy 120.2505 126.893713) (xy 145.6495 126.893713) (xy 145.6495 127.106287) + (xy 145.659534 127.169644) (xy 145.679598 127.296321) (xy 145.682754 127.316243) (xy 145.718446 127.426092) + (xy 145.748444 127.518414) (xy 145.844951 127.70782) (xy 145.96989 127.879786) (xy 146.120213 128.030109) + (xy 146.292179 128.155048) (xy 146.292181 128.155049) (xy 146.292184 128.155051) (xy 146.481588 128.251557) + (xy 146.683757 128.317246) (xy 146.893713 128.3505) (xy 146.893714 128.3505) (xy 147.106286 128.3505) + (xy 147.106287 128.3505) (xy 147.316243 128.317246) (xy 147.518412 128.251557) (xy 147.707816 128.155051) + (xy 147.777639 128.104322) (xy 147.879786 128.030109) (xy 147.879788 128.030106) (xy 147.879792 128.030104) + (xy 148.030104 127.879792) (xy 148.030106 127.879788) (xy 148.030109 127.879786) (xy 148.155048 127.70782) + (xy 148.155047 127.70782) (xy 148.155051 127.707816) (xy 148.251557 127.518412) (xy 148.317246 127.316243) + (xy 148.3505 127.106287) (xy 148.3505 126.893713) (xy 148.317246 126.683757) (xy 148.251557 126.481588) + (xy 148.155051 126.292184) (xy 148.155049 126.292181) (xy 148.155048 126.292179) (xy 148.030109 126.120213) + (xy 147.879786 125.96989) (xy 147.70782 125.844951) (xy 147.518414 125.748444) (xy 147.518413 125.748443) + (xy 147.518412 125.748443) (xy 147.316243 125.682754) (xy 147.316241 125.682753) (xy 147.31624 125.682753) + (xy 147.154957 125.657208) (xy 147.106287 125.6495) (xy 146.893713 125.6495) (xy 146.845042 125.657208) + (xy 146.68376 125.682753) (xy 146.481585 125.748444) (xy 146.292179 125.844951) (xy 146.120213 125.96989) + (xy 145.96989 126.120213) (xy 145.844951 126.292179) (xy 145.748444 126.481585) (xy 145.682753 126.68376) + (xy 145.6495 126.893713) (xy 120.2505 126.893713) (xy 120.2505 126.663399) (xy 120.270185 126.59636) + (xy 120.322989 126.550605) (xy 120.392147 126.540661) (xy 120.398692 126.541782) (xy 120.521155 126.566142) + (xy 120.521158 126.566142) (xy 120.678844 126.566142) (xy 120.678845 126.566141) (xy 120.833497 126.535379) + (xy 120.979179 126.475036) (xy 121.110289 126.387431) (xy 121.221789 126.275931) (xy 121.309394 126.144821) + (xy 121.369737 125.999139) (xy 121.4005 125.844484) (xy 121.4005 125.705047) (xy 121.420185 125.638008) + (xy 121.472989 125.592253) (xy 121.476986 125.590512) (xy 121.479179 125.589604) (xy 121.600848 125.508306) + (xy 121.667525 125.487429) (xy 121.734906 125.505913) (xy 121.781596 125.557892) (xy 121.784299 125.563953) + (xy 121.790603 125.579172) (xy 121.790606 125.579178) (xy 121.790609 125.579185) (xy 121.87821 125.710288) + (xy 121.878213 125.710292) (xy 121.989707 125.821786) (xy 121.989711 125.821789) (xy 122.120814 125.90939) + (xy 122.120827 125.909397) (xy 122.266498 125.969735) (xy 122.266503 125.969737) (xy 122.414276 125.999131) + (xy 122.421153 126.000499) (xy 122.421156 126.0005) (xy 122.421158 126.0005) (xy 122.578844 126.0005) + (xy 122.578845 126.000499) (xy 122.733497 125.969737) (xy 122.879179 125.909394) (xy 123.010289 125.821789) + (xy 123.121789 125.710289) (xy 123.209394 125.579179) (xy 123.269737 125.433497) (xy 123.3005 125.278842) + (xy 123.3005 125.121158) (xy 123.3005 125.121155) (xy 123.300499 125.121153) (xy 123.284255 125.039488) + (xy 123.269737 124.966503) (xy 123.266651 124.959052) (xy 123.209397 124.820827) (xy 123.20939 124.820814) + (xy 123.121789 124.689711) (xy 123.121786 124.689707) (xy 123.100622 124.668543) (xy 131.679499 124.668543) + (xy 131.717947 124.861829) (xy 131.71795 124.861839) (xy 131.793364 125.043907) (xy 131.793371 125.04392) + (xy 131.90286 125.207781) (xy 131.902863 125.207785) (xy 132.042214 125.347136) (xy 132.042218 125.347139) + (xy 132.206079 125.456628) (xy 132.206092 125.456635) (xy 132.363383 125.521786) (xy 132.388165 125.532051) + (xy 132.388169 125.532051) (xy 132.38817 125.532052) (xy 132.581456 125.5705) (xy 132.581459 125.5705) + (xy 132.778543 125.5705) (xy 132.908582 125.544632) (xy 132.971835 125.532051) (xy 133.153914 125.456632) + (xy 133.317782 125.347139) (xy 133.457139 125.207782) (xy 133.566632 125.043914) (xy 133.566631 125.043914) + (xy 133.570017 125.038848) (xy 133.571474 125.039821) (xy 133.614595 124.995903) (xy 133.682729 124.980426) + (xy 133.748414 125.004242) (xy 133.750502 125.005809) (xy 133.756632 125.010512) (xy 133.756635 125.010515) + (xy 133.887865 125.086281) (xy 134.034234 125.1255) (xy 134.034236 125.1255) (xy 134.185764 125.1255) + (xy 134.185766 125.1255) (xy 134.332135 125.086281) (xy 134.463365 125.010515) (xy 134.570515 124.903365) + (xy 134.61798 124.821153) (xy 136.1995 124.821153) (xy 136.1995 124.978846) (xy 136.230261 125.133489) + (xy 136.230264 125.133501) (xy 136.290602 125.279172) (xy 136.290609 125.279185) (xy 136.37821 125.410288) + (xy 136.378213 125.410292) (xy 136.489707 125.521786) (xy 136.489711 125.521789) (xy 136.620814 125.60939) + (xy 136.620827 125.609397) (xy 136.717646 125.6495) (xy 136.766503 125.669737) (xy 136.921153 125.700499) + (xy 136.921156 125.7005) (xy 136.921158 125.7005) (xy 137.078844 125.7005) (xy 137.078845 125.700499) + (xy 137.233497 125.669737) (xy 137.379179 125.609394) (xy 137.510289 125.521789) (xy 137.621789 125.410289) + (xy 137.709394 125.279179) (xy 137.769737 125.133497) (xy 137.8005 124.978842) (xy 137.8005 124.821158) + (xy 137.8005 124.821155) (xy 137.800499 124.821153) (xy 137.774353 124.689711) (xy 137.769737 124.666503) + (xy 137.76154 124.646713) (xy 137.709397 124.520827) (xy 137.70939 124.520814) (xy 137.678266 124.474234) + (xy 139.3145 124.474234) (xy 139.3145 124.625766) (xy 139.325962 124.668543) (xy 139.353719 124.772136) + (xy 139.391602 124.83775) (xy 139.429485 124.903365) (xy 139.536635 125.010515) (xy 139.667865 125.086281) + (xy 139.814234 125.1255) (xy 139.814236 125.1255) (xy 139.965764 125.1255) (xy 139.965766 125.1255) + (xy 140.112135 125.086281) (xy 140.243365 125.010515) (xy 140.243374 125.010505) (xy 140.249488 125.005815) + (xy 140.314656 124.980617) (xy 140.383101 124.99465) (xy 140.429025 125.039488) (xy 140.429983 125.038849) + (xy 140.433009 125.043378) (xy 140.433094 125.043461) (xy 140.433228 125.043706) (xy 140.54286 125.207781) + (xy 140.542863 125.207785) (xy 140.682214 125.347136) (xy 140.682218 125.347139) (xy 140.846079 125.456628) + (xy 140.846092 125.456635) (xy 141.003383 125.521786) (xy 141.028165 125.532051) (xy 141.028169 125.532051) + (xy 141.02817 125.532052) (xy 141.221456 125.5705) (xy 141.221459 125.5705) (xy 141.418543 125.5705) + (xy 141.548582 125.544632) (xy 141.611835 125.532051) (xy 141.669886 125.508004) (xy 141.739353 125.500535) + (xy 141.78623 125.519463) (xy 141.920814 125.60939) (xy 141.920827 125.609397) (xy 142.017646 125.6495) + (xy 142.066503 125.669737) (xy 142.221153 125.700499) (xy 142.221156 125.7005) (xy 142.221158 125.7005) + (xy 142.378844 125.7005) (xy 142.378845 125.700499) (xy 142.533497 125.669737) (xy 142.679179 125.609394) + (xy 142.810289 125.521789) (xy 142.921789 125.410289) (xy 143.009394 125.279179) (xy 143.069737 125.133497) + (xy 143.1005 124.978842) (xy 143.1005 124.821158) (xy 143.1005 124.821155) (xy 143.100499 124.821153) + (xy 143.074353 124.689711) (xy 143.069737 124.666503) (xy 143.06154 124.646713) (xy 143.009397 124.520827) + (xy 143.00939 124.520814) (xy 142.921789 124.389711) (xy 142.921786 124.389707) (xy 142.810292 124.278213) + (xy 142.810288 124.27821) (xy 142.679185 124.190609) (xy 142.679172 124.190602) (xy 142.533501 124.130264) + (xy 142.533491 124.130261) (xy 142.420308 124.107747) (xy 142.358397 124.075362) (xy 142.323823 124.014646) + (xy 142.3205 123.98613) (xy 142.3205 123.371456) (xy 142.282052 123.17817) (xy 142.282051 123.178169) + (xy 142.282051 123.178165) (xy 142.252511 123.106849) (xy 142.206635 122.996092) (xy 142.206628 122.996079) + (xy 142.097139 122.832218) (xy 142.097136 122.832214) (xy 141.957785 122.692863) (xy 141.957781 122.69286) + (xy 141.79392 122.583371) (xy 141.793907 122.583364) (xy 141.680511 122.536395) (xy 141.611839 122.50795) + (xy 141.611829 122.507947) (xy 141.418543 122.4695) (xy 141.418541 122.4695) (xy 141.221459 122.4695) + (xy 141.221457 122.4695) (xy 141.02817 122.507947) (xy 141.02816 122.50795) (xy 140.846092 122.583364) + (xy 140.846079 122.583371) (xy 140.682218 122.69286) (xy 140.682214 122.692863) (xy 140.542863 122.832214) + (xy 140.54286 122.832218) (xy 140.433371 122.996079) (xy 140.433364 122.996092) (xy 140.35795 123.17816) (xy 140.357947 123.17817) (xy 140.3195 123.371456) (xy 140.3195 123.918666) (xy 140.299815 123.985705) (xy 140.247011 124.03146) (xy 140.177853 124.041404) (xy 140.133501 124.026054) (xy 140.112137 124.013719) - (xy 140.004994 123.985011) (xy 139.965766 123.9745) (xy 139.814234 123.9745) (xy 139.667863 124.013719) + (xy 140.007584 123.985705) (xy 139.965766 123.9745) (xy 139.814234 123.9745) (xy 139.667863 124.013719) (xy 139.536635 124.089485) (xy 139.536632 124.089487) (xy 139.429487 124.196632) (xy 139.429485 124.196635) - (xy 139.353719 124.327863) (xy 139.316975 124.464998) (xy 139.3145 124.474234) (xy 139.3145 124.625766) - (xy 139.325962 124.668543) (xy 139.353719 124.772136) (xy 139.375747 124.810289) (xy 139.429485 124.903365) - (xy 139.536635 125.010515) (xy 139.667865 125.086281) (xy 139.814234 125.1255) (xy 139.814236 125.1255) - (xy 139.965764 125.1255) (xy 139.965766 125.1255) (xy 140.112135 125.086281) (xy 140.243365 125.010515) - (xy 140.243374 125.010505) (xy 140.249488 125.005815) (xy 140.314656 124.980617) (xy 140.383101 124.99465) - (xy 140.429025 125.039488) (xy 140.429983 125.038849) (xy 140.433009 125.043378) (xy 140.433094 125.043461) - (xy 140.433228 125.043706) (xy 140.54286 125.207781) (xy 140.542863 125.207785) (xy 140.682214 125.347136) - (xy 140.682218 125.347139) (xy 140.846079 125.456628) (xy 140.846092 125.456635) (xy 141.023848 125.530263) - (xy 141.028165 125.532051) (xy 141.028169 125.532051) (xy 141.02817 125.532052) (xy 141.221456 125.5705) - (xy 141.221459 125.5705) (xy 141.418543 125.5705) (xy 141.548582 125.544632) (xy 141.611835 125.532051) - (xy 141.793914 125.456632) (xy 141.957782 125.347139) (xy 142.097139 125.207782) (xy 142.206632 125.043914) - (xy 142.282051 124.861835) (xy 142.294632 124.798582) (xy 142.3205 124.668543) (xy 142.3205 123.371456) - (xy 142.282052 123.17817) (xy 142.282051 123.178169) (xy 142.282051 123.178165) (xy 142.223272 123.036258) - (xy 142.206635 122.996092) (xy 142.206628 122.996079) (xy 142.097139 122.832218) (xy 142.097136 122.832214) - (xy 141.957785 122.692863) (xy 141.957781 122.69286) (xy 141.79392 122.583371) (xy 141.793911 122.583366) - (xy 141.680511 122.536395) (xy 141.644088 122.521308) (xy 141.589685 122.477467) (xy 141.572216 122.424983) - (xy 144.0995 122.424983) (xy 144.0995 123.775001) (xy 144.099501 123.775018) (xy 144.11 123.877796) - (xy 144.110001 123.877799) (xy 144.165185 124.044331) (xy 144.165187 124.044336) (xy 144.18887 124.082732) - (xy 144.257288 124.193656) (xy 144.381344 124.317712) (xy 144.530666 124.409814) (xy 144.697203 124.464999) - (xy 144.799991 124.4755) (xy 145.600008 124.475499) (xy 145.600016 124.475498) (xy 145.600019 124.475498) - (xy 145.656302 124.469748) (xy 145.702797 124.464999) (xy 145.869334 124.409814) (xy 146.018656 124.317712) - (xy 146.142712 124.193656) (xy 146.18231 124.129456) (xy 146.234258 124.082732) (xy 146.30322 124.071509) - (xy 146.367303 124.099352) (xy 146.37553 124.106872) (xy 146.483072 124.214414) (xy 146.623212 124.316232) - (xy 146.777555 124.394873) (xy 146.942299 124.448402) (xy 147.113389 124.4755) (xy 147.11339 124.4755) - (xy 147.28661 124.4755) (xy 147.286611 124.4755) (xy 147.457701 124.448402) (xy 147.622445 124.394873) - (xy 147.776788 124.316232) (xy 147.916928 124.214414) (xy 148.039414 124.091928) (xy 148.141232 123.951788) - (xy 148.219873 123.797445) (xy 148.273402 123.632701) (xy 148.3005 123.461611) (xy 148.3005 122.738389) - (xy 148.273402 122.567299) (xy 148.219873 122.402555) (xy 148.141232 122.248212) (xy 148.039414 122.108072) - (xy 147.916928 121.985586) (xy 147.776788 121.883768) (xy 147.622445 121.805127) (xy 147.457701 121.751598) - (xy 147.457699 121.751597) (xy 147.457698 121.751597) (xy 147.326271 121.730781) (xy 147.286611 121.7245) - (xy 147.113389 121.7245) (xy 147.073728 121.730781) (xy 146.942302 121.751597) (xy 146.777552 121.805128) - (xy 146.623211 121.883768) (xy 146.483073 121.985585) (xy 146.37553 122.093128) (xy 146.314207 122.126612) - (xy 146.244515 122.121628) (xy 146.188582 122.079756) (xy 146.18231 122.070543) (xy 146.142712 122.006344) - (xy 146.018656 121.882288) (xy 145.893559 121.805128) (xy 145.869336 121.790187) (xy 145.869331 121.790185) - (xy 145.867862 121.789698) (xy 145.702797 121.735001) (xy 145.702795 121.735) (xy 145.60001 121.7245) - (xy 144.799998 121.7245) (xy 144.79998 121.724501) (xy 144.697203 121.735) (xy 144.6972 121.735001) - (xy 144.530668 121.790185) (xy 144.530663 121.790187) (xy 144.381342 121.882289) (xy 144.257289 122.006342) - (xy 144.165187 122.155663) (xy 144.165185 122.155668) (xy 144.146257 122.212789) (xy 144.110001 122.322203) - (xy 144.110001 122.322204) (xy 144.11 122.322204) (xy 144.0995 122.424983) (xy 141.572216 122.424983) - (xy 141.56762 122.411173) (xy 141.569924 122.382555) (xy 141.6005 122.228844) (xy 141.6005 122.071155) - (xy 141.600499 122.071153) (xy 141.600378 122.070543) (xy 141.569737 121.916503) (xy 141.555565 121.882288) - (xy 141.509397 121.770827) (xy 141.50939 121.770814) (xy 141.421789 121.639711) (xy 141.421786 121.639707) - (xy 141.310292 121.528213) (xy 141.310288 121.52821) (xy 141.179185 121.440609) (xy 141.179172 121.440602) - (xy 141.033501 121.380264) (xy 141.033489 121.380261) (xy 140.878845 121.3495) (xy 140.878842 121.3495) - (xy 140.721158 121.3495) (xy 140.721155 121.3495) (xy 140.56651 121.380261) (xy 140.566498 121.380264) - (xy 140.420827 121.440602) (xy 140.420816 121.440608) (xy 140.320499 121.507638) (xy 140.253822 121.528515) - (xy 140.186442 121.51003) (xy 140.148507 121.473426) (xy 140.071789 121.358611) (xy 140.071786 121.358607) - (xy 139.960292 121.247113) (xy 139.960288 121.24711) (xy 139.829185 121.159509) (xy 139.829172 121.159502) - (xy 139.683501 121.099164) (xy 139.683489 121.099161) (xy 139.528845 121.0684) (xy 139.528842 121.0684) - (xy 139.371158 121.0684) (xy 139.371155 121.0684) (xy 139.21651 121.099161) (xy 139.216498 121.099164) - (xy 139.070827 121.159502) (xy 139.070814 121.159509) (xy 138.939711 121.24711) (xy 138.939707 121.247113) - (xy 138.828213 121.358607) (xy 138.82821 121.358611) (xy 138.76909 121.447091) (xy 138.715478 121.491896) - (xy 138.665988 121.5022) (xy 136.668206 121.5022) (xy 136.601167 121.482515) (xy 136.555412 121.429711) - (xy 136.546589 121.402392) (xy 136.519738 121.267408) (xy 136.519737 121.267407) (xy 136.519737 121.267403) - (xy 136.511332 121.247111) (xy 136.459397 121.121727) (xy 136.45939 121.121714) (xy 136.371789 120.990611) - (xy 136.371786 120.990607) (xy 136.260292 120.879113) (xy 136.260288 120.87911) (xy 136.129185 120.791509) - (xy 136.129172 120.791502) (xy 135.983501 120.731164) (xy 135.983489 120.731161) (xy 135.828845 120.7004) - (xy 135.828842 120.7004) (xy 135.671158 120.7004) (xy 135.671155 120.7004) (xy 135.51651 120.731161) - (xy 135.516498 120.731164) (xy 135.370827 120.791502) (xy 135.370814 120.791509) (xy 135.239711 120.87911) - (xy 135.239707 120.879113) (xy 135.156027 120.962794) (xy 135.094704 120.996279) (xy 135.025012 120.991295) - (xy 135.020894 120.989674) (xy 134.884815 120.933309) (xy 134.844582 120.906425) (xy 134.842343 120.904186) - (xy 134.842342 120.904185) (xy 134.842341 120.904184) (xy 134.727607 120.827522) (xy 134.600132 120.774721) - (xy 134.600122 120.774718) (xy 134.464796 120.7478) (xy 134.464794 120.7478) (xy 134.464793 120.7478) - (xy 129.915994 120.7478) (xy 129.778006 120.7478) (xy 129.778004 120.7478) (xy 129.642677 120.774718) - (xy 129.642667 120.774721) (xy 129.515192 120.827522) (xy 129.400454 120.904187) (xy 125.575412 124.729229) - (xy 125.535184 124.756109) (xy 125.390823 124.815904) (xy 125.390814 124.815909) (xy 125.259711 124.90351) - (xy 125.259707 124.903513) (xy 125.148213 125.015007) (xy 125.14821 125.015011) (xy 125.060609 125.146114) - (xy 125.060602 125.146127) (xy 125.000264 125.291798) (xy 125.000261 125.29181) (xy 124.9695 125.446453) - (xy 123.340722 125.446453) (xy 123.333907 125.43) (xy 123.309397 125.370827) (xy 123.309393 125.37082) - (xy 123.309389 125.370814) (xy 123.241284 125.268888) (xy 123.220408 125.202214) (xy 123.238892 125.134834) - (xy 123.241257 125.131152) (xy 123.309394 125.029179) (xy 123.369737 124.883497) (xy 123.4005 124.728842) - (xy 123.4005 124.571158) (xy 123.4005 124.571155) (xy 123.400499 124.571153) (xy 123.395071 124.543867) - (xy 123.369737 124.416503) (xy 123.354138 124.378844) (xy 123.309397 124.270827) (xy 123.30939 124.270814) - (xy 123.221789 124.139711) (xy 123.221786 124.139707) (xy 123.128413 124.046334) (xy 123.094928 123.985011) - (xy 123.099912 123.915319) (xy 123.141784 123.859386) (xy 123.196695 123.83618) (xy 123.272524 123.82417) - (xy 123.316238 123.817247) (xy 123.316238 123.817246) (xy 123.316243 123.817246) (xy 123.518412 123.751557) - (xy 123.707816 123.655051) (xy 123.738584 123.632697) (xy 123.879786 123.530109) (xy 123.879788 123.530106) - (xy 123.879792 123.530104) (xy 124.030104 123.379792) (xy 124.030106 123.379788) (xy 124.030109 123.379786) - (xy 124.155048 123.20782) (xy 124.155047 123.20782) (xy 124.155051 123.207816) (xy 124.251557 123.018412) - (xy 124.317246 122.816243) (xy 124.3505 122.606287) (xy 124.3505 122.393713) (xy 124.317246 122.183757) - (xy 124.251557 121.981588) (xy 124.155051 121.792184) (xy 124.155049 121.792181) (xy 124.155048 121.792179) - (xy 124.030109 121.620213) (xy 123.879786 121.46989) (xy 123.70782 121.344951) (xy 123.518414 121.248444) - (xy 123.518413 121.248443) (xy 123.518412 121.248443) (xy 123.316243 121.182754) (xy 123.316241 121.182753) - (xy 123.31624 121.182753) (xy 123.154957 121.157208) (xy 123.106287 121.1495) (xy 122.893713 121.1495) - (xy 122.845042 121.157208) (xy 122.68376 121.182753) (xy 122.683757 121.182754) (xy 122.485688 121.247111) - (xy 122.481585 121.248444) (xy 122.292179 121.344951) (xy 122.120213 121.46989) (xy 121.96989 121.620213) - (xy 121.844951 121.792179) (xy 121.748444 121.981585) (xy 121.682753 122.18376) (xy 121.659059 122.33336) - (xy 121.6495 122.393713) (xy 120.2505 122.393713) (xy 120.2505 119.236153) (xy 120.9495 119.236153) - (xy 120.9495 119.393846) (xy 120.980261 119.548489) (xy 120.980264 119.548501) (xy 121.040602 119.694172) - (xy 121.040609 119.694185) (xy 121.12821 119.825288) (xy 121.128213 119.825292) (xy 121.239707 119.936786) - (xy 121.239711 119.936789) (xy 121.370814 120.02439) (xy 121.370827 120.024397) (xy 121.47006 120.0655) - (xy 121.516503 120.084737) (xy 121.671153 120.115499) (xy 121.671156 120.1155) (xy 121.671158 120.1155) - (xy 121.828844 120.1155) (xy 121.828845 120.115499) (xy 121.983497 120.084737) (xy 122.129179 120.024394) - (xy 122.260289 119.936789) (xy 122.371789 119.825289) (xy 122.459394 119.694179) (xy 122.519737 119.548497) - (xy 122.5505 119.393842) (xy 122.5505 119.236158) (xy 122.5505 119.236155) (xy 122.550499 119.236153) - (xy 122.537517 119.170889) (xy 122.519737 119.081503) (xy 122.501497 119.037468) (xy 122.459397 118.935827) - (xy 122.45939 118.935814) (xy 122.371789 118.804711) (xy 122.371786 118.804707) (xy 122.260292 118.693213) - (xy 122.260288 118.69321) (xy 122.129185 118.605609) (xy 122.129172 118.605602) (xy 121.983501 118.545264) - (xy 121.983489 118.545261) (xy 121.828845 118.5145) (xy 121.828842 118.5145) (xy 121.671158 118.5145) - (xy 121.671155 118.5145) (xy 121.51651 118.545261) (xy 121.516498 118.545264) (xy 121.370827 118.605602) - (xy 121.370814 118.605609) (xy 121.239711 118.69321) (xy 121.239707 118.693213) (xy 121.128213 118.804707) - (xy 121.12821 118.804711) (xy 121.040609 118.935814) (xy 121.040602 118.935827) (xy 120.980264 119.081498) - (xy 120.980261 119.08151) (xy 120.9495 119.236153) (xy 120.2505 119.236153) (xy 120.2505 117.511888) - (xy 122.573765 117.511888) (xy 122.573765 117.669581) (xy 122.604526 117.824224) (xy 122.604529 117.824236) - (xy 122.664867 117.969907) (xy 122.664874 117.96992) (xy 122.752475 118.101023) (xy 122.752478 118.101027) - (xy 122.863972 118.212521) (xy 122.863976 118.212524) (xy 122.995079 118.300125) (xy 122.995092 118.300132) - (xy 123.07864 118.334738) (xy 123.140768 118.360472) (xy 123.295418 118.391234) (xy 123.295421 118.391235) - (xy 123.295423 118.391235) (xy 123.453109 118.391235) (xy 123.45311 118.391234) (xy 123.607762 118.360472) - (xy 123.753444 118.300129) (xy 123.849191 118.236153) (xy 124.9495 118.236153) (xy 124.9495 118.393846) - (xy 124.980261 118.548489) (xy 124.980264 118.548501) (xy 125.040602 118.694172) (xy 125.040609 118.694185) - (xy 125.12821 118.825288) (xy 125.128213 118.825292) (xy 125.239707 118.936786) (xy 125.239711 118.936789) - (xy 125.370814 119.02439) (xy 125.370827 119.024397) (xy 125.508683 119.081498) (xy 125.516503 119.084737) - (xy 125.671153 119.115499) (xy 125.671156 119.1155) (xy 125.671158 119.1155) (xy 125.828844 119.1155) - (xy 125.828845 119.115499) (xy 125.983497 119.084737) (xy 126.129179 119.024394) (xy 126.260289 118.936789) - (xy 126.371789 118.825289) (xy 126.459394 118.694179) (xy 126.519737 118.548497) (xy 126.5505 118.393842) - (xy 126.5505 118.236158) (xy 126.5505 118.236155) (xy 126.550499 118.236153) (xy 126.536963 118.168102) - (xy 126.519737 118.081503) (xy 126.512901 118.065) (xy 126.459397 117.935827) (xy 126.45939 117.935814) - (xy 126.371789 117.804711) (xy 126.371786 117.804707) (xy 126.260292 117.693213) (xy 126.260288 117.69321) - (xy 126.129185 117.605609) (xy 126.129172 117.605602) (xy 125.983501 117.545264) (xy 125.983489 117.545261) - (xy 125.828845 117.5145) (xy 125.828842 117.5145) (xy 125.671158 117.5145) (xy 125.671155 117.5145) - (xy 125.51651 117.545261) (xy 125.516498 117.545264) (xy 125.370827 117.605602) (xy 125.370814 117.605609) - (xy 125.239711 117.69321) (xy 125.239707 117.693213) (xy 125.128213 117.804707) (xy 125.12821 117.804711) - (xy 125.040609 117.935814) (xy 125.040602 117.935827) (xy 124.980264 118.081498) (xy 124.980261 118.08151) - (xy 124.9495 118.236153) (xy 123.849191 118.236153) (xy 123.884554 118.212524) (xy 123.910292 118.186786) - (xy 123.954694 118.142385) (xy 123.996051 118.101027) (xy 123.996054 118.101024) (xy 124.083659 117.969914) - (xy 124.144002 117.824232) (xy 124.174765 117.669577) (xy 124.174765 117.511893) (xy 124.174765 117.51189) - (xy 124.174764 117.511888) (xy 124.144003 117.357245) (xy 124.144002 117.357238) (xy 124.130769 117.325291) - (xy 124.083662 117.211562) (xy 124.083655 117.211549) (xy 123.996054 117.080446) (xy 123.996051 117.080442) - (xy 123.884557 116.968948) (xy 123.884553 116.968945) (xy 123.75345 116.881344) (xy 123.753437 116.881337) - (xy 123.664809 116.844627) (xy 123.607766 116.820999) (xy 123.607754 116.820996) (xy 123.45311 116.790235) - (xy 123.453107 116.790235) (xy 123.295423 116.790235) (xy 123.29542 116.790235) (xy 123.140775 116.820996) - (xy 123.140763 116.820999) (xy 122.995092 116.881337) (xy 122.995079 116.881344) (xy 122.863976 116.968945) - (xy 122.863972 116.968948) (xy 122.752478 117.080442) (xy 122.752475 117.080446) (xy 122.664874 117.211549) - (xy 122.664867 117.211562) (xy 122.604529 117.357233) (xy 122.604526 117.357245) (xy 122.573765 117.511888) - (xy 120.2505 117.511888) (xy 120.2505 116.736153) (xy 128.970134 116.736153) (xy 128.970134 116.893846) - (xy 129.000895 117.048489) (xy 129.000898 117.048501) (xy 129.061236 117.194172) (xy 129.061243 117.194185) - (xy 129.148844 117.325288) (xy 129.148847 117.325292) (xy 129.164419 117.340864) (xy 129.197904 117.402187) - (xy 129.19292 117.471879) (xy 129.179842 117.497433) (xy 129.173534 117.506872) (xy 129.124499 117.625255) - (xy 129.124497 117.625261) (xy 129.0995 117.750928) (xy 129.0995 117.750931) (xy 129.0995 117.879069) - (xy 129.0995 117.879071) (xy 129.099499 117.879071) (xy 129.124497 118.004738) (xy 129.124499 118.004744) - (xy 129.173533 118.123124) (xy 129.173538 118.123133) (xy 129.244723 118.229668) (xy 129.248589 118.234379) - (xy 129.246958 118.235716) (xy 129.275858 118.288642) (xy 129.270874 118.358334) (xy 129.247489 118.394719) - (xy 129.248589 118.395621) (xy 129.244723 118.400331) (xy 129.173538 118.506866) (xy 129.173533 118.506875) - (xy 129.124499 118.625255) (xy 129.124497 118.625261) (xy 129.0995 118.750928) (xy 129.0995 118.750931) - (xy 129.0995 118.879069) (xy 129.0995 118.879071) (xy 129.099499 118.879071) (xy 129.124497 119.004738) - (xy 129.1245 119.004748) (xy 129.172281 119.120102) (xy 129.17975 119.189571) (xy 129.163401 119.230066) - (xy 129.164113 119.230447) (xy 129.161236 119.235828) (xy 129.100898 119.381498) (xy 129.100895 119.38151) - (xy 129.070134 119.536153) (xy 129.070134 119.693846) (xy 129.100895 119.848489) (xy 129.100898 119.848501) - (xy 129.161236 119.994172) (xy 129.161243 119.994185) (xy 129.248844 120.125288) (xy 129.248847 120.125292) - (xy 129.360341 120.236786) (xy 129.360345 120.236789) (xy 129.491448 120.32439) (xy 129.491461 120.324397) - (xy 129.637132 120.384735) (xy 129.637137 120.384737) (xy 129.791787 120.415499) (xy 129.79179 120.4155) - (xy 129.791792 120.4155) (xy 129.949478 120.4155) (xy 129.949479 120.415499) (xy 130.104131 120.384737) - (xy 130.249813 120.324394) (xy 130.380923 120.236789) (xy 130.492423 120.125289) (xy 130.580028 119.994179) - (xy 130.640371 119.848497) (xy 130.671134 119.693842) (xy 130.671134 119.536158) (xy 130.671134 119.536155) - (xy 130.671133 119.536153) (xy 130.668793 119.52439) (xy 130.640371 119.381503) (xy 130.624773 119.343846) - (xy 130.580028 119.23582) (xy 130.546841 119.186153) (xy 132.1995 119.186153) (xy 132.1995 119.343846) - (xy 132.230261 119.498489) (xy 132.230264 119.498501) (xy 132.290602 119.644172) (xy 132.290609 119.644185) - (xy 132.37821 119.775288) (xy 132.378213 119.775292) (xy 132.489707 119.886786) (xy 132.489711 119.886789) - (xy 132.620814 119.97439) (xy 132.620827 119.974397) (xy 132.766498 120.034735) (xy 132.766503 120.034737) - (xy 132.921153 120.065499) (xy 132.921156 120.0655) (xy 132.921158 120.0655) (xy 133.078844 120.0655) - (xy 133.078845 120.065499) (xy 133.233497 120.034737) (xy 133.379179 119.974394) (xy 133.510289 119.886789) - (xy 133.621789 119.775289) (xy 133.621792 119.775283) (xy 133.624351 119.772725) (xy 133.685674 119.73924) - (xy 133.725537 119.738884) (xy 133.725693 119.737303) (xy 133.731756 119.7379) (xy 133.731758 119.7379) - (xy 133.889444 119.7379) (xy 133.889445 119.737899) (xy 134.044097 119.707137) (xy 134.189779 119.646794) - (xy 134.320889 119.559189) (xy 134.432389 119.447689) (xy 134.519994 119.316579) (xy 134.580337 119.170897) - (xy 134.6111 119.016242) (xy 134.6111 118.858558) (xy 134.6111 118.858555) (xy 134.611099 118.858553) - (xy 134.590443 118.754711) (xy 134.580337 118.703903) (xy 134.555198 118.643211) (xy 134.519997 118.558227) - (xy 134.51999 118.558214) (xy 134.432389 118.427111) (xy 134.432386 118.427107) (xy 134.320892 118.315613) - (xy 134.320888 118.31561) (xy 134.189785 118.228009) (xy 134.189772 118.228002) (xy 134.044101 118.167664) - (xy 134.044089 118.167661) (xy 133.889445 118.1369) (xy 133.889442 118.1369) (xy 133.731758 118.1369) - (xy 133.731755 118.1369) (xy 133.57711 118.167661) (xy 133.577098 118.167664) (xy 133.431427 118.228002) - (xy 133.431414 118.228009) (xy 133.300311 118.31561) (xy 133.186246 118.429675) (xy 133.124923 118.463159) - (xy 133.08506 118.463524) (xy 133.084906 118.465097) (xy 133.078844 118.4645) (xy 133.078842 118.4645) - (xy 132.921158 118.4645) (xy 132.921155 118.4645) (xy 132.76651 118.495261) (xy 132.766498 118.495264) - (xy 132.620827 118.555602) (xy 132.620814 118.555609) (xy 132.489711 118.64321) (xy 132.489707 118.643213) - (xy 132.378213 118.754707) (xy 132.37821 118.754711) (xy 132.290609 118.885814) (xy 132.290602 118.885827) - (xy 132.230264 119.031498) (xy 132.230261 119.03151) (xy 132.1995 119.186153) (xy 130.546841 119.186153) - (xy 130.492423 119.104711) (xy 130.49242 119.104707) (xy 130.425181 119.037468) (xy 130.391696 118.976145) - (xy 130.391245 118.925594) (xy 130.397561 118.893846) (xy 130.4005 118.879069) (xy 130.4005 118.750931) - (xy 130.4005 118.750928) (xy 130.375502 118.625261) (xy 130.375501 118.62526) (xy 130.375501 118.625256) - (xy 130.326465 118.506873) (xy 130.326464 118.506872) (xy 130.326461 118.506866) (xy 130.255276 118.400331) - (xy 130.251411 118.395621) (xy 130.253045 118.394279) (xy 130.224148 118.341389) (xy 130.229114 118.271696) - (xy 130.252514 118.235284) (xy 130.251411 118.234379) (xy 130.255271 118.229673) (xy 130.255276 118.229669) - (xy 130.326465 118.123127) (xy 130.375501 118.004744) (xy 130.387547 117.944185) (xy 130.4005 117.879071) - (xy 130.4005 117.750928) (xy 130.375502 117.625261) (xy 130.375501 117.62526) (xy 130.375501 117.625256) - (xy 130.343708 117.548501) (xy 130.324306 117.501659) (xy 130.322639 117.486153) (xy 130.6495 117.486153) - (xy 130.6495 117.643846) (xy 130.680261 117.798489) (xy 130.680264 117.798501) (xy 130.740602 117.944172) - (xy 130.740609 117.944185) (xy 130.82821 118.075288) (xy 130.828213 118.075292) (xy 130.939707 118.186786) - (xy 130.939711 118.186789) (xy 131.070814 118.27439) (xy 131.070827 118.274397) (xy 131.170328 118.315611) - (xy 131.216503 118.334737) (xy 131.345871 118.36047) (xy 131.371153 118.365499) (xy 131.371156 118.3655) - (xy 131.371158 118.3655) (xy 131.528844 118.3655) (xy 131.528845 118.365499) (xy 131.683497 118.334737) - (xy 131.829179 118.274394) (xy 131.960289 118.186789) (xy 132.071789 118.075289) (xy 132.159394 117.944179) - (xy 132.162854 117.935827) (xy 132.20864 117.825288) (xy 132.219737 117.798497) (xy 132.2505 117.643842) - (xy 132.2505 117.486158) (xy 132.2505 117.486155) (xy 132.250499 117.486153) (xy 132.219738 117.33151) - (xy 132.219737 117.331503) (xy 132.180242 117.236153) (xy 135.4495 117.236153) (xy 135.4495 117.393846) - (xy 135.480261 117.548489) (xy 135.480264 117.548501) (xy 135.540602 117.694172) (xy 135.540609 117.694185) - (xy 135.62821 117.825288) (xy 135.628213 117.825292) (xy 135.739707 117.936786) (xy 135.73971 117.936788) - (xy 135.739711 117.936789) (xy 135.750771 117.944179) (xy 135.777289 117.961898) (xy 135.822093 118.015511) - (xy 135.8308 118.084836) (xy 135.800645 118.147863) (xy 135.777289 118.168102) (xy 135.739707 118.193213) - (xy 135.628213 118.304707) (xy 135.62821 118.304711) (xy 135.540609 118.435814) (xy 135.540602 118.435827) - (xy 135.480264 118.581498) (xy 135.480261 118.58151) (xy 135.4495 118.736153) (xy 135.4495 118.893846) - (xy 135.480261 119.048489) (xy 135.480264 119.048501) (xy 135.540602 119.194172) (xy 135.540609 119.194185) - (xy 135.62821 119.325288) (xy 135.628213 119.325292) (xy 135.739707 119.436786) (xy 135.739711 119.436789) - (xy 135.870814 119.52439) (xy 135.870827 119.524397) (xy 135.954824 119.559189) (xy 136.016503 119.584737) - (xy 136.171153 119.615499) (xy 136.171156 119.6155) (xy 136.171158 119.6155) (xy 136.328844 119.6155) - (xy 136.328845 119.615499) (xy 136.483497 119.584737) (xy 136.629179 119.524394) (xy 136.760289 119.436789) - (xy 136.871789 119.325289) (xy 136.959394 119.194179) (xy 136.962719 119.186153) (xy 136.991984 119.115499) - (xy 137.019737 119.048497) (xy 137.0505 118.893842) (xy 137.0505 118.736158) (xy 137.0505 118.736155) - (xy 137.050499 118.736153) (xy 137.032012 118.643213) (xy 137.019737 118.581503) (xy 137.010093 118.558221) - (xy 136.959397 118.435827) (xy 136.95939 118.435814) (xy 136.871789 118.304711) (xy 136.871786 118.304707) - (xy 136.760292 118.193213) (xy 136.760284 118.193207) (xy 136.722712 118.168102) (xy 136.677906 118.11449) - (xy 136.669199 118.045165) (xy 136.699353 117.982138) (xy 136.722712 117.961898) (xy 136.749279 117.944145) - (xy 136.760289 117.936789) (xy 136.871789 117.825289) (xy 136.959394 117.694179) (xy 137.019737 117.548497) - (xy 137.0505 117.393842) (xy 137.0505 117.236158) (xy 137.0505 117.236155) (xy 137.050499 117.236153) - (xy 137.050125 117.234271) (xy 137.019737 117.081503) (xy 137.019298 117.080442) (xy 136.959397 116.935827) - (xy 136.95939 116.935814) (xy 136.871789 116.804711) (xy 136.871786 116.804707) (xy 136.760292 116.693213) - (xy 136.760288 116.69321) (xy 136.629185 116.605609) (xy 136.629172 116.605602) (xy 136.483501 116.545264) - (xy 136.483489 116.545261) (xy 136.328845 116.5145) (xy 136.328842 116.5145) (xy 136.171158 116.5145) - (xy 136.171155 116.5145) (xy 136.01651 116.545261) (xy 136.016498 116.545264) (xy 135.870827 116.605602) - (xy 135.870814 116.605609) (xy 135.739711 116.69321) (xy 135.739707 116.693213) (xy 135.628213 116.804707) - (xy 135.62821 116.804711) (xy 135.540609 116.935814) (xy 135.540602 116.935827) (xy 135.480264 117.081498) - (xy 135.480261 117.08151) (xy 135.4495 117.236153) (xy 132.180242 117.236153) (xy 132.179933 117.235408) - (xy 132.159397 117.185827) (xy 132.15939 117.185814) (xy 132.071789 117.054711) (xy 132.071786 117.054707) - (xy 131.960292 116.943213) (xy 131.960288 116.94321) (xy 131.829185 116.855609) (xy 131.829172 116.855602) - (xy 131.683501 116.795264) (xy 131.683489 116.795261) (xy 131.528845 116.7645) (xy 131.528842 116.7645) - (xy 131.371158 116.7645) (xy 131.371155 116.7645) (xy 131.21651 116.795261) (xy 131.216498 116.795264) - (xy 131.070827 116.855602) (xy 131.070814 116.855609) (xy 130.939711 116.94321) (xy 130.939707 116.943213) - (xy 130.828213 117.054707) (xy 130.82821 117.054711) (xy 130.767395 117.145726) (xy 130.767391 117.145734) - (xy 130.740606 117.185821) (xy 130.680263 117.331503) (xy 130.679324 117.33622) (xy 130.679322 117.336226) - (xy 130.6495 117.486153) (xy 130.322639 117.486153) (xy 130.316837 117.43219) (xy 130.348112 117.369711) - (xy 130.351187 117.366525) (xy 130.392421 117.325291) (xy 130.392423 117.325289) (xy 130.480028 117.194179) - (xy 130.540371 117.048497) (xy 130.571134 116.893842) (xy 130.571134 116.736158) (xy 130.571134 116.736155) - (xy 130.571133 116.736153) (xy 130.545165 116.605606) (xy 130.540371 116.581503) (xy 130.540369 116.581498) - (xy 130.480031 116.435827) (xy 130.480024 116.435814) (xy 130.392423 116.304711) (xy 130.39242 116.304707) - (xy 130.280926 116.193213) (xy 130.280922 116.19321) (xy 130.149819 116.105609) (xy 130.149806 116.105602) - (xy 130.004135 116.045264) (xy 130.004123 116.045261) (xy 129.849479 116.0145) (xy 129.849476 116.0145) - (xy 129.691792 116.0145) (xy 129.691789 116.0145) (xy 129.537144 116.045261) (xy 129.537132 116.045264) - (xy 129.391461 116.105602) (xy 129.391448 116.105609) (xy 129.260345 116.19321) (xy 129.260341 116.193213) - (xy 129.148847 116.304707) (xy 129.148844 116.304711) (xy 129.061243 116.435814) (xy 129.061236 116.435827) - (xy 129.000898 116.581498) (xy 129.000895 116.58151) (xy 128.970134 116.736153) (xy 120.2505 116.736153) - (xy 120.2505 114.221153) (xy 136.6495 114.221153) (xy 136.6495 114.378846) (xy 136.680261 114.533489) - (xy 136.680264 114.533501) (xy 136.740602 114.679172) (xy 136.740609 114.679185) (xy 136.82821 114.810288) - (xy 136.828213 114.810292) (xy 136.939707 114.921786) (xy 136.939711 114.921789) (xy 137.070814 115.00939) - (xy 137.070827 115.009397) (xy 137.216498 115.069735) (xy 137.216503 115.069737) (xy 137.371153 115.100499) - (xy 137.371156 115.1005) (xy 137.371158 115.1005) (xy 137.528844 115.1005) (xy 137.528845 115.100499) - (xy 137.683497 115.069737) (xy 137.829179 115.009394) (xy 137.960289 114.921789) (xy 138.071789 114.810289) - (xy 138.144453 114.70154) (xy 145.5542 114.70154) (xy 145.5542 114.848459) (xy 145.582858 114.992534) - (xy 145.582861 114.992544) (xy 145.639078 115.128266) (xy 145.639083 115.128275) (xy 145.720698 115.250419) - (xy 145.720701 115.250423) (xy 145.824576 115.354298) (xy 145.82458 115.354301) (xy 145.946724 115.435916) - (xy 145.94673 115.435919) (xy 145.946731 115.43592) (xy 146.082458 115.49214) (xy 146.22654 115.520799) - (xy 146.226544 115.5208) (xy 146.226545 115.5208) (xy 146.373456 115.5208) (xy 146.373457 115.520799) - (xy 146.517542 115.49214) (xy 146.653269 115.43592) (xy 146.77542 115.354301) (xy 146.879301 115.25042) - (xy 146.96092 115.128269) (xy 147.01714 114.992542) (xy 147.0458 114.848455) (xy 147.0458 114.701545) - (xy 147.01714 114.557458) (xy 146.96092 114.421731) (xy 146.960919 114.42173) (xy 146.960916 114.421724) - (xy 146.879301 114.29958) (xy 146.879298 114.299576) (xy 146.775423 114.195701) (xy 146.775419 114.195698) - (xy 146.653275 114.114083) (xy 146.653266 114.114078) (xy 146.517544 114.057861) (xy 146.517545 114.057861) - (xy 146.517542 114.05786) (xy 146.517538 114.057859) (xy 146.517534 114.057858) (xy 146.373459 114.0292) - (xy 146.373455 114.0292) (xy 146.226545 114.0292) (xy 146.22654 114.0292) (xy 146.082465 114.057858) - (xy 146.082455 114.057861) (xy 145.946733 114.114078) (xy 145.946724 114.114083) (xy 145.82458 114.195698) - (xy 145.824576 114.195701) (xy 145.720701 114.299576) (xy 145.720698 114.29958) (xy 145.639083 114.421724) - (xy 145.639078 114.421733) (xy 145.582861 114.557455) (xy 145.582858 114.557465) (xy 145.5542 114.70154) - (xy 138.144453 114.70154) (xy 138.159394 114.679179) (xy 138.219737 114.533497) (xy 138.2505 114.378842) - (xy 138.2505 114.221158) (xy 138.2505 114.221155) (xy 138.250499 114.221153) (xy 138.229201 114.114083) - (xy 138.219737 114.066503) (xy 138.204286 114.0292) (xy 138.159397 113.920827) (xy 138.15939 113.920814) - (xy 138.071789 113.789711) (xy 138.071786 113.789707) (xy 137.960292 113.678213) (xy 137.960288 113.67821) - (xy 137.829185 113.590609) (xy 137.829172 113.590602) (xy 137.683501 113.530264) (xy 137.683489 113.530261) - (xy 137.528845 113.4995) (xy 137.528842 113.4995) (xy 137.371158 113.4995) (xy 137.371155 113.4995) - (xy 137.21651 113.530261) (xy 137.216498 113.530264) (xy 137.070827 113.590602) (xy 137.070814 113.590609) - (xy 136.939711 113.67821) (xy 136.939707 113.678213) (xy 136.828213 113.789707) (xy 136.82821 113.789711) - (xy 136.740609 113.920814) (xy 136.740602 113.920827) (xy 136.680264 114.066498) (xy 136.680261 114.06651) - (xy 136.6495 114.221153) (xy 120.2505 114.221153) (xy 120.2505 110.902753) (xy 140.3162 110.902753) - (xy 140.3162 111.060446) (xy 140.346961 111.215089) (xy 140.346964 111.215101) (xy 140.407302 111.360772) - (xy 140.407309 111.360785) (xy 140.49491 111.491888) (xy 140.494913 111.491892) (xy 140.606407 111.603386) - (xy 140.606411 111.603389) (xy 140.737514 111.69099) (xy 140.737527 111.690997) (xy 140.841304 111.733982) - (xy 140.883203 111.751337) (xy 141.037853 111.782099) (xy 141.037856 111.7821) (xy 141.037858 111.7821) - (xy 141.195544 111.7821) (xy 141.195545 111.782099) (xy 141.350197 111.751337) (xy 141.495879 111.690994) - (xy 141.626989 111.603389) (xy 141.738489 111.491889) (xy 141.826094 111.360779) (xy 141.886437 111.215097) - (xy 141.913473 111.079179) (xy 141.917338 111.05975) (xy 141.949723 110.997839) (xy 141.951217 110.996317) - (xy 142.326381 110.621153) (xy 144.1495 110.621153) (xy 144.1495 110.778846) (xy 144.180261 110.933489) - (xy 144.180264 110.933501) (xy 144.240602 111.079172) (xy 144.240609 111.079185) (xy 144.32821 111.210288) - (xy 144.328213 111.210292) (xy 144.439707 111.321786) (xy 144.439711 111.321789) (xy 144.570814 111.40939) - (xy 144.570827 111.409397) (xy 144.716498 111.469735) (xy 144.716503 111.469737) (xy 144.871153 111.500499) - (xy 144.871156 111.5005) (xy 144.871158 111.5005) (xy 145.028844 111.5005) (xy 145.028845 111.500499) - (xy 145.183497 111.469737) (xy 145.329179 111.409394) (xy 145.460289 111.321789) (xy 145.571789 111.210289) - (xy 145.659394 111.079179) (xy 145.719737 110.933497) (xy 145.7505 110.778842) (xy 145.7505 110.621158) - (xy 145.7505 110.621155) (xy 145.750499 110.621153) (xy 145.731847 110.527385) (xy 145.719737 110.466503) - (xy 145.704926 110.430747) (xy 145.697458 110.361281) (xy 145.728732 110.298802) (xy 145.750591 110.280199) - (xy 145.75942 110.274301) (xy 145.863301 110.17042) (xy 145.94492 110.048269) (xy 146.00114 109.912542) - (xy 146.0298 109.768455) (xy 146.0298 109.621545) (xy 146.00114 109.477458) (xy 145.94492 109.341731) - (xy 145.944919 109.34173) (xy 145.944916 109.341724) (xy 145.863301 109.21958) (xy 145.863298 109.219576) - (xy 145.759423 109.115701) (xy 145.759419 109.115698) (xy 145.637275 109.034083) (xy 145.637266 109.034078) - (xy 145.526611 108.988244) (xy 145.501542 108.97786) (xy 145.501538 108.977859) (xy 145.501534 108.977858) - (xy 145.357459 108.9492) (xy 145.357455 108.9492) (xy 145.210545 108.9492) (xy 145.21054 108.9492) - (xy 145.066465 108.977858) (xy 145.066455 108.977861) (xy 144.930733 109.034078) (xy 144.930724 109.034083) - (xy 144.80858 109.115698) (xy 144.808576 109.115701) (xy 144.704701 109.219576) (xy 144.704698 109.21958) - (xy 144.623083 109.341724) (xy 144.623078 109.341733) (xy 144.566861 109.477455) (xy 144.566858 109.477465) - (xy 144.5382 109.62154) (xy 144.5382 109.621544) (xy 144.5382 109.621545) (xy 144.5382 109.768455) - (xy 144.538201 109.768459) (xy 144.564867 109.902523) (xy 144.558638 109.972114) (xy 144.515775 110.027291) - (xy 144.51214 110.029815) (xy 144.439711 110.07821) (xy 144.439707 110.078213) (xy 144.328213 110.189707) - (xy 144.32821 110.189711) (xy 144.240609 110.320814) (xy 144.240602 110.320827) (xy 144.180264 110.466498) - (xy 144.180261 110.46651) (xy 144.1495 110.621153) (xy 142.326381 110.621153) (xy 144.687017 108.260519) - (xy 144.74834 108.227034) (xy 144.774698 108.2242) (xy 145.271034 108.2242) (xy 145.338073 108.243885) - (xy 145.339925 108.245098) (xy 145.471614 108.33309) (xy 145.471627 108.333097) (xy 145.617298 108.393435) - (xy 145.617303 108.393437) (xy 145.759822 108.421786) (xy 145.771953 108.424199) (xy 145.771956 108.4242) - (xy 145.771958 108.4242) (xy 145.929644 108.4242) (xy 145.929645 108.424199) (xy 146.084297 108.393437) - (xy 146.229979 108.333094) (xy 146.361089 108.245489) (xy 146.472589 108.133989) (xy 146.560194 108.002879) - (xy 146.620537 107.857197) (xy 146.6513 107.702542) (xy 146.6513 107.544858) (xy 146.6513 107.544855) - (xy 146.651299 107.544853) (xy 146.63393 107.457533) (xy 146.620537 107.390203) (xy 146.599176 107.338632) - (xy 146.560197 107.244527) (xy 146.56019 107.244514) (xy 146.472589 107.113411) (xy 146.472586 107.113407) - (xy 146.361092 107.001913) (xy 146.361088 107.00191) (xy 146.229985 106.914309) (xy 146.229972 106.914302) - (xy 146.084301 106.853964) (xy 146.084289 106.853961) (xy 145.929645 106.8232) (xy 145.929642 106.8232) - (xy 145.771958 106.8232) (xy 145.771955 106.8232) (xy 145.61731 106.853961) (xy 145.617298 106.853964) - (xy 145.471627 106.914302) (xy 145.471614 106.914309) (xy 145.339925 107.002302) (xy 145.273247 107.02318) - (xy 145.271034 107.0232) (xy 144.56127 107.0232) (xy 144.561254 107.023199) (xy 144.553658 107.023199) - (xy 144.395543 107.023199) (xy 144.319179 107.043661) (xy 144.242814 107.064123) (xy 144.242809 107.064126) - (xy 144.10589 107.143175) (xy 144.105882 107.143181) (xy 141.102039 110.147025) (xy 141.040716 110.18051) - (xy 141.03855 110.180961) (xy 140.883208 110.211861) (xy 140.883198 110.211864) (xy 140.737527 110.272202) - (xy 140.737514 110.272209) (xy 140.606411 110.35981) (xy 140.606407 110.359813) (xy 140.494913 110.471307) - (xy 140.49491 110.471311) (xy 140.407309 110.602414) (xy 140.407302 110.602427) (xy 140.346964 110.748098) - (xy 140.346961 110.74811) (xy 140.3162 110.902753) (xy 120.2505 110.902753) (xy 120.2505 107.071153) - (xy 120.4995 107.071153) (xy 120.4995 107.228846) (xy 120.530261 107.383489) (xy 120.530264 107.383501) - (xy 120.590602 107.529172) (xy 120.590609 107.529185) (xy 120.67821 107.660288) (xy 120.678213 107.660292) - (xy 120.789707 107.771786) (xy 120.789711 107.771789) (xy 120.920814 107.85939) (xy 120.920827 107.859397) - (xy 120.996181 107.890609) (xy 121.066503 107.919737) (xy 121.221153 107.950499) (xy 121.221156 107.9505) - (xy 121.221158 107.9505) (xy 121.378844 107.9505) (xy 121.378845 107.950499) (xy 121.533497 107.919737) - (xy 121.679179 107.859394) (xy 121.810289 107.771789) (xy 121.860925 107.721153) (xy 130.1495 107.721153) - (xy 130.1495 107.878846) (xy 130.180261 108.033489) (xy 130.180264 108.033501) (xy 130.240602 108.179172) - (xy 130.240609 108.179185) (xy 130.32821 108.310288) (xy 130.328213 108.310292) (xy 130.439707 108.421786) - (xy 130.439711 108.421789) (xy 130.570814 108.50939) (xy 130.570827 108.509397) (xy 130.716387 108.569689) - (xy 130.716503 108.569737) (xy 130.871153 108.600499) (xy 130.871156 108.6005) (xy 130.871158 108.6005) - (xy 131.028844 108.6005) (xy 131.028845 108.600499) (xy 131.183497 108.569737) (xy 131.329179 108.509394) - (xy 131.460289 108.421789) (xy 131.571789 108.310289) (xy 131.659394 108.179179) (xy 131.719737 108.033497) - (xy 131.7505 107.878842) (xy 131.7505 107.721158) (xy 131.7505 107.721155) (xy 131.750499 107.721153) - (xy 131.734943 107.642949) (xy 131.719737 107.566503) (xy 131.719721 107.566464) (xy 131.659397 107.420827) - (xy 131.65939 107.420814) (xy 131.571789 107.289711) (xy 131.571786 107.289707) (xy 131.460292 107.178213) - (xy 131.460288 107.17821) (xy 131.329185 107.090609) (xy 131.329172 107.090602) (xy 131.183501 107.030264) - (xy 131.183489 107.030261) (xy 131.028845 106.9995) (xy 131.028842 106.9995) (xy 130.871158 106.9995) - (xy 130.871155 106.9995) (xy 130.71651 107.030261) (xy 130.716498 107.030264) (xy 130.570827 107.090602) - (xy 130.570814 107.090609) (xy 130.439711 107.17821) (xy 130.439707 107.178213) (xy 130.328213 107.289707) - (xy 130.32821 107.289711) (xy 130.240609 107.420814) (xy 130.240602 107.420827) (xy 130.180264 107.566498) - (xy 130.180261 107.56651) (xy 130.1495 107.721153) (xy 121.860925 107.721153) (xy 121.921789 107.660289) - (xy 121.933376 107.642949) (xy 122.00939 107.529185) (xy 122.00939 107.529184) (xy 122.009394 107.529179) - (xy 122.069737 107.383497) (xy 122.1005 107.228842) (xy 122.1005 107.071158) (xy 122.1005 107.071155) - (xy 122.100499 107.071153) (xy 122.09096 107.023199) (xy 122.069737 106.916503) (xy 122.043832 106.853963) - (xy 122.016327 106.787558) (xy 122.016311 106.78752) (xy 122.015679 106.785995) (xy 122.009394 106.770821) - (xy 122.009391 106.770816) (xy 122.00939 106.770814) (xy 121.992912 106.746153) (xy 134.4495 106.746153) - (xy 134.4495 106.903846) (xy 134.480261 107.058489) (xy 134.480264 107.058501) (xy 134.540602 107.204172) - (xy 134.540609 107.204185) (xy 134.62821 107.335288) (xy 134.628213 107.335292) (xy 134.739707 107.446786) - (xy 134.739711 107.446789) (xy 134.870814 107.53439) (xy 134.870827 107.534397) (xy 134.948356 107.56651) - (xy 135.016503 107.594737) (xy 135.054443 107.602283) (xy 135.096068 107.610564) (xy 135.157979 107.642949) - (xy 135.192553 107.703664) (xy 135.188814 107.773434) (xy 135.159562 107.819858) (xy 135.153515 107.825904) - (xy 135.15351 107.825911) (xy 135.065909 107.957014) (xy 135.065902 107.957027) (xy 135.005564 108.102698) - (xy 135.005561 108.10271) (xy 134.9748 108.257353) (xy 134.9748 108.415046) (xy 135.005561 108.569689) - (xy 135.005564 108.569701) (xy 135.065902 108.715372) (xy 135.065909 108.715385) (xy 135.15351 108.846488) - (xy 135.153513 108.846492) (xy 135.265007 108.957986) (xy 135.265011 108.957989) (xy 135.396114 109.04559) - (xy 135.396127 109.045597) (xy 135.541798 109.105935) (xy 135.541803 109.105937) (xy 135.694342 109.136279) - (xy 135.696453 109.136699) (xy 135.696456 109.1367) (xy 135.696458 109.1367) (xy 135.854144 109.1367) - (xy 135.854145 109.136699) (xy 136.008797 109.105937) (xy 136.154479 109.045594) (xy 136.285589 108.957989) - (xy 136.397089 108.846489) (xy 136.484694 108.715379) (xy 136.545037 108.569697) (xy 136.554693 108.521153) - (xy 139.6995 108.521153) (xy 139.6995 108.678846) (xy 139.730261 108.833489) (xy 139.730264 108.833501) - (xy 139.790602 108.979172) (xy 139.790609 108.979185) (xy 139.87821 109.110288) (xy 139.878213 109.110292) - (xy 139.989707 109.221786) (xy 139.989711 109.221789) (xy 140.120814 109.30939) (xy 140.120827 109.309397) - (xy 140.266498 109.369735) (xy 140.266503 109.369737) (xy 140.421153 109.400499) (xy 140.421156 109.4005) - (xy 140.421158 109.4005) (xy 140.578844 109.4005) (xy 140.578845 109.400499) (xy 140.733497 109.369737) - (xy 140.879179 109.309394) (xy 141.010289 109.221789) (xy 141.121789 109.110289) (xy 141.209394 108.979179) - (xy 141.269737 108.833497) (xy 141.3005 108.678842) (xy 141.3005 108.521158) (xy 141.3005 108.521155) - (xy 141.300499 108.521153) (xy 141.294476 108.490874) (xy 141.269737 108.366503) (xy 141.246452 108.310288) - (xy 141.209397 108.220827) (xy 141.20939 108.220814) (xy 141.121789 108.089711) (xy 141.121786 108.089707) - (xy 141.010292 107.978213) (xy 141.010288 107.97821) (xy 140.879185 107.890609) (xy 140.879172 107.890602) - (xy 140.733501 107.830264) (xy 140.733489 107.830261) (xy 140.578845 107.7995) (xy 140.578842 107.7995) - (xy 140.421158 107.7995) (xy 140.421155 107.7995) (xy 140.26651 107.830261) (xy 140.266498 107.830264) - (xy 140.120827 107.890602) (xy 140.120814 107.890609) (xy 139.989711 107.97821) (xy 139.989707 107.978213) - (xy 139.878213 108.089707) (xy 139.87821 108.089711) (xy 139.790609 108.220814) (xy 139.790602 108.220827) - (xy 139.730264 108.366498) (xy 139.730261 108.36651) (xy 139.6995 108.521153) (xy 136.554693 108.521153) - (xy 136.556416 108.51249) (xy 136.560716 108.490875) (xy 136.560716 108.490874) (xy 136.5758 108.415044) - (xy 136.5758 108.257355) (xy 136.575799 108.257353) (xy 136.560248 108.179172) (xy 136.545037 108.102703) - (xy 136.516368 108.033489) (xy 136.484697 107.957027) (xy 136.48469 107.957014) (xy 136.397089 107.825911) - (xy 136.397086 107.825907) (xy 136.285592 107.714413) (xy 136.285588 107.71441) (xy 136.154485 107.626809) - (xy 136.154472 107.626802) (xy 136.008801 107.566464) (xy 136.008791 107.566461) (xy 135.92923 107.550635) - (xy 135.867319 107.518249) (xy 135.832745 107.457533) (xy 135.836486 107.387764) (xy 135.865745 107.341333) - (xy 135.871788 107.33529) (xy 135.871789 107.335289) (xy 135.959394 107.204179) (xy 136.019737 107.058497) - (xy 136.0505 106.903842) (xy 136.0505 106.746158) (xy 136.0505 106.746155) (xy 136.050499 106.746153) - (xy 136.019738 106.59151) (xy 136.019737 106.591503) (xy 135.993521 106.528211) (xy 135.959397 106.445827) - (xy 135.959389 106.445813) (xy 135.951468 106.433958) (xy 135.951467 106.433957) (xy 135.909503 106.371153) - (xy 142.4995 106.371153) (xy 142.4995 106.528846) (xy 142.530261 106.683489) (xy 142.530264 106.683501) - (xy 142.590602 106.829172) (xy 142.590609 106.829185) (xy 142.67821 106.960288) (xy 142.678213 106.960292) - (xy 142.789707 107.071786) (xy 142.789711 107.071789) (xy 142.920814 107.15939) (xy 142.920827 107.159397) - (xy 143.066498 107.219735) (xy 143.066503 107.219737) (xy 143.191065 107.244514) (xy 143.221153 107.250499) - (xy 143.221156 107.2505) (xy 143.221158 107.2505) (xy 143.378844 107.2505) (xy 143.378845 107.250499) - (xy 143.533497 107.219737) (xy 143.679179 107.159394) (xy 143.810289 107.071789) (xy 143.921789 106.960289) - (xy 144.009394 106.829179) (xy 144.069737 106.683497) (xy 144.1005 106.528842) (xy 144.1005 106.371158) - (xy 144.1005 106.371155) (xy 144.100499 106.371153) (xy 144.069738 106.21651) (xy 144.069737 106.216503) - (xy 144.027946 106.115609) (xy 144.009397 106.070827) (xy 144.00939 106.070814) (xy 143.921789 105.939711) - (xy 143.921786 105.939707) (xy 143.810292 105.828213) (xy 143.810288 105.82821) (xy 143.679185 105.740609) - (xy 143.679172 105.740602) (xy 143.533501 105.680264) (xy 143.533489 105.680261) (xy 143.378845 105.6495) - (xy 143.378842 105.6495) (xy 143.221158 105.6495) (xy 143.221155 105.6495) (xy 143.06651 105.680261) - (xy 143.066498 105.680264) (xy 142.920827 105.740602) (xy 142.920814 105.740609) (xy 142.789711 105.82821) - (xy 142.789707 105.828213) (xy 142.678213 105.939707) (xy 142.67821 105.939711) (xy 142.590609 106.070814) - (xy 142.590602 106.070827) (xy 142.530264 106.216498) (xy 142.530261 106.21651) (xy 142.4995 106.371153) - (xy 135.909503 106.371153) (xy 135.871789 106.314711) (xy 135.871786 106.314707) (xy 135.760292 106.203213) - (xy 135.760288 106.20321) (xy 135.629185 106.115609) (xy 135.629172 106.115602) (xy 135.483501 106.055264) - (xy 135.483489 106.055261) (xy 135.328845 106.0245) (xy 135.328842 106.0245) (xy 135.171158 106.0245) - (xy 135.171155 106.0245) (xy 135.01651 106.055261) (xy 135.016498 106.055264) (xy 134.870827 106.115602) - (xy 134.870814 106.115609) (xy 134.739711 106.20321) (xy 134.739707 106.203213) (xy 134.628213 106.314707) - (xy 134.62821 106.314711) (xy 134.540609 106.445814) (xy 134.540602 106.445827) (xy 134.480264 106.591498) - (xy 134.480261 106.59151) (xy 134.4495 106.746153) (xy 121.992912 106.746153) (xy 121.921789 106.639711) - (xy 121.921786 106.639707) (xy 121.810292 106.528213) (xy 121.810288 106.52821) (xy 121.679185 106.440609) - (xy 121.679172 106.440602) (xy 121.533501 106.380264) (xy 121.533489 106.380261) (xy 121.378845 106.3495) - (xy 121.378842 106.3495) (xy 121.221158 106.3495) (xy 121.221155 106.3495) (xy 121.06651 106.380261) - (xy 121.066498 106.380264) (xy 120.920827 106.440602) (xy 120.920814 106.440609) (xy 120.789711 106.52821) - (xy 120.789707 106.528213) (xy 120.678213 106.639707) (xy 120.67821 106.639711) (xy 120.590609 106.770814) - (xy 120.590602 106.770827) (xy 120.530264 106.916498) (xy 120.530261 106.91651) (xy 120.4995 107.071153) - (xy 120.2505 107.071153) (xy 120.2505 105.071153) (xy 121.5495 105.071153) (xy 121.5495 105.228846) - (xy 121.580261 105.383489) (xy 121.580264 105.383501) (xy 121.640602 105.529172) (xy 121.640609 105.529185) - (xy 121.72821 105.660288) (xy 121.728213 105.660292) (xy 121.839707 105.771786) (xy 121.839711 105.771789) - (xy 121.970814 105.85939) (xy 121.970827 105.859397) (xy 122.092269 105.909699) (xy 122.116503 105.919737) - (xy 122.271153 105.950499) (xy 122.271156 105.9505) (xy 122.271158 105.9505) (xy 122.428844 105.9505) - (xy 122.428845 105.950499) (xy 122.583497 105.919737) (xy 122.729179 105.859394) (xy 122.860289 105.771789) - (xy 122.971789 105.660289) (xy 123.059394 105.529179) (xy 123.059395 105.529176) (xy 123.059397 105.529173) - (xy 123.11294 105.399906) (xy 123.15678 105.345502) (xy 123.203309 105.325741) (xy 123.233497 105.319737) - (xy 123.379179 105.259394) (xy 123.510289 105.171789) (xy 123.621789 105.060289) (xy 123.709394 104.929179) - (xy 123.769737 104.783497) (xy 123.792282 104.670158) (xy 123.792283 104.670153) (xy 124.1591 104.670153) - (xy 124.1591 104.827846) (xy 124.189861 104.982489) (xy 124.189864 104.982501) (xy 124.250202 105.128172) - (xy 124.250209 105.128185) (xy 124.33781 105.259288) (xy 124.337813 105.259292) (xy 124.449307 105.370786) - (xy 124.449311 105.370789) (xy 124.580414 105.45839) (xy 124.580427 105.458397) (xy 124.652826 105.488385) - (xy 124.726103 105.518737) (xy 124.880753 105.549499) (xy 124.880756 105.5495) (xy 124.880758 105.5495) - (xy 125.038444 105.5495) (xy 125.038445 105.549499) (xy 125.193097 105.518737) (xy 125.338779 105.458394) - (xy 125.469889 105.370789) (xy 125.581389 105.259289) (xy 125.668994 105.128179) (xy 125.729337 104.982497) - (xy 125.7601 104.827842) (xy 125.7601 104.670158) (xy 125.7601 104.670155) (xy 125.760099 104.670153) - (xy 125.729337 104.515503) (xy 125.71038 104.469736) (xy 125.668997 104.369827) (xy 125.66899 104.369814) - (xy 125.581389 104.238711) (xy 125.581386 104.238707) (xy 125.469892 104.127213) (xy 125.469888 104.12721) - (xy 125.338785 104.039609) (xy 125.338772 104.039602) (xy 125.193101 103.979264) (xy 125.193089 103.979261) - (xy 125.038445 103.9485) (xy 125.038442 103.9485) (xy 124.880758 103.9485) (xy 124.880755 103.9485) - (xy 124.72611 103.979261) (xy 124.726098 103.979264) (xy 124.580427 104.039602) (xy 124.580414 104.039609) - (xy 124.449311 104.12721) (xy 124.449307 104.127213) (xy 124.337813 104.238707) (xy 124.33781 104.238711) - (xy 124.250209 104.369814) (xy 124.250202 104.369827) (xy 124.189864 104.515498) (xy 124.189861 104.51551) - (xy 124.1591 104.670153) (xy 123.792283 104.670153) (xy 123.798306 104.639875) (xy 123.798306 104.639874) - (xy 123.8005 104.628844) (xy 123.8005 104.471155) (xy 123.800499 104.471153) (xy 123.780344 104.369827) - (xy 123.769737 104.316503) (xy 123.733427 104.228842) (xy 123.709397 104.170827) (xy 123.70939 104.170814) - (xy 123.621789 104.039711) (xy 123.621786 104.039707) (xy 123.510292 103.928213) (xy 123.510286 103.928208) - (xy 123.49771 103.919805) (xy 123.452906 103.866193) (xy 123.444199 103.796867) (xy 123.474354 103.73384) - (xy 123.497708 103.713603) (xy 123.560289 103.671789) (xy 123.671789 103.560289) (xy 123.759394 103.429179) - (xy 123.819737 103.283497) (xy 123.8505 103.128842) (xy 123.8505 102.971158) (xy 123.8505 102.971155) - (xy 123.850499 102.971153) (xy 123.828447 102.860292) (xy 123.819737 102.816503) (xy 123.783569 102.729185) - (xy 123.759397 102.670827) (xy 123.75939 102.670814) (xy 123.671789 102.539711) (xy 123.671786 102.539707) - (xy 123.560292 102.428213) (xy 123.560288 102.42821) (xy 123.429185 102.340609) (xy 123.429172 102.340602) - (xy 123.283501 102.280264) (xy 123.283489 102.280261) (xy 123.128845 102.2495) (xy 123.128842 102.2495) - (xy 122.971158 102.2495) (xy 122.971155 102.2495) (xy 122.81651 102.280261) (xy 122.816498 102.280264) - (xy 122.670827 102.340602) (xy 122.670814 102.340609) (xy 122.539711 102.42821) (xy 122.539707 102.428213) - (xy 122.428213 102.539707) (xy 122.42821 102.539711) (xy 122.340609 102.670814) (xy 122.340602 102.670827) - (xy 122.280264 102.816498) (xy 122.280261 102.81651) (xy 122.2495 102.971153) (xy 122.2495 103.128846) - (xy 122.280261 103.283489) (xy 122.280264 103.283501) (xy 122.340602 103.429172) (xy 122.340609 103.429185) - (xy 122.42821 103.560288) (xy 122.428213 103.560292) (xy 122.539707 103.671786) (xy 122.539711 103.671789) - (xy 122.552288 103.680193) (xy 122.597093 103.733805) (xy 122.6058 103.80313) (xy 122.575646 103.866157) - (xy 122.552289 103.886396) (xy 122.489713 103.928208) (xy 122.489707 103.928213) (xy 122.378213 104.039707) - (xy 122.37821 104.039711) (xy 122.290609 104.170814) (xy 122.290604 104.170824) (xy 122.237059 104.300094) - (xy 122.193218 104.354497) (xy 122.14669 104.374258) (xy 122.116508 104.380261) (xy 122.116498 104.380264) - (xy 121.970827 104.440602) (xy 121.970814 104.440609) (xy 121.839711 104.52821) (xy 121.839707 104.528213) - (xy 121.728213 104.639707) (xy 121.72821 104.639711) (xy 121.640609 104.770814) (xy 121.640602 104.770827) - (xy 121.580264 104.916498) (xy 121.580261 104.91651) (xy 121.5495 105.071153) (xy 120.2505 105.071153) - (xy 120.2505 97.940666) (xy 120.270185 97.873627) (xy 120.322989 97.827872) (xy 120.392147 97.817928) - (xy 120.421951 97.826105) (xy 120.426217 97.827872) (xy 120.455097 97.839835) (xy 120.455099 97.839835) - (xy 120.455103 97.839837) (xy 120.519747 97.852695) (xy 120.610449 97.870738) (xy 120.67236 97.903123) - (xy 120.673938 97.904673) (xy 124.665984 101.89672) (xy 124.665986 101.896721) (xy 124.66599 101.896724) - (xy 124.788841 101.967651) (xy 124.802916 101.975777) (xy 124.955643 102.016701) (xy 124.955645 102.016701) - (xy 125.121354 102.016701) (xy 125.12137 102.0167) (xy 128.030003 102.0167) (xy 128.097042 102.036385) - (xy 128.117679 102.053014) (xy 128.284632 102.219968) (xy 128.318116 102.28129) (xy 128.313132 102.350982) - (xy 128.27126 102.406915) (xy 128.265843 102.410748) (xy 128.239716 102.428206) (xy 128.239707 102.428213) - (xy 128.128213 102.539707) (xy 128.12821 102.539711) (xy 128.040609 102.670814) (xy 128.040602 102.670827) - (xy 127.980264 102.816498) (xy 127.980261 102.81651) (xy 127.9495 102.971153) (xy 127.9495 103.128846) - (xy 127.980261 103.283489) (xy 127.980264 103.283501) (xy 128.040602 103.429172) (xy 128.040609 103.429185) - (xy 128.12821 103.560288) (xy 128.128213 103.560292) (xy 128.239707 103.671786) (xy 128.239711 103.671789) - (xy 128.370814 103.75939) (xy 128.370827 103.759397) (xy 128.516498 103.819735) (xy 128.516503 103.819737) - (xy 128.621418 103.840606) (xy 128.671153 103.850499) (xy 128.671156 103.8505) (xy 128.671158 103.8505) - (xy 128.828844 103.8505) (xy 128.828845 103.850499) (xy 128.983497 103.819737) (xy 129.101592 103.770821) - (xy 129.129172 103.759397) (xy 129.129172 103.759396) (xy 129.129179 103.759394) (xy 129.260289 103.671789) - (xy 129.371789 103.560289) (xy 129.425262 103.480261) (xy 129.438117 103.461023) (xy 129.491729 103.416217) - (xy 129.561054 103.40751) (xy 129.624081 103.437664) (xy 129.660801 103.497107) (xy 129.662836 103.554104) - (xy 129.649499 103.621153) (xy 129.649499 103.778846) (xy 129.68026 103.933489) (xy 129.680263 103.933501) - (xy 129.740601 104.079172) (xy 129.740608 104.079185) (xy 129.828209 104.210288) (xy 129.828212 104.210292) - (xy 129.939706 104.321786) (xy 129.93971 104.321789) (xy 130.070813 104.40939) (xy 130.070826 104.409397) - (xy 130.18602 104.457111) (xy 130.216502 104.469737) (xy 130.305355 104.487411) (xy 130.371152 104.500499) - (xy 130.371155 104.5005) (xy 130.409179 104.5005) (xy 130.476218 104.520185) (xy 130.521973 104.572989) - (xy 130.531917 104.642147) (xy 130.512281 104.693391) (xy 130.487809 104.730014) (xy 130.487802 104.730027) - (xy 130.427464 104.875698) (xy 130.427461 104.87571) (xy 130.3967 105.030353) (xy 130.3967 105.188046) - (xy 130.427461 105.342689) (xy 130.427464 105.342701) (xy 130.487802 105.488372) (xy 130.487809 105.488385) - (xy 130.57541 105.619488) (xy 130.575413 105.619492) (xy 130.686907 105.730986) (xy 130.686911 105.730989) - (xy 130.818014 105.81859) (xy 130.818027 105.818597) (xy 130.963698 105.878935) (xy 130.963703 105.878937) - (xy 131.118353 105.909699) (xy 131.118356 105.9097) (xy 131.118358 105.9097) (xy 131.276044 105.9097) - (xy 131.276045 105.909699) (xy 131.430697 105.878937) (xy 131.576379 105.818594) (xy 131.707489 105.730989) - (xy 131.818989 105.619489) (xy 131.906594 105.488379) (xy 131.966937 105.342697) (xy 131.9977 105.188042) - (xy 131.9977 105.0745) (xy 132.017385 105.007461) (xy 132.070189 104.961706) (xy 132.1217 104.9505) - (xy 132.228844 104.9505) (xy 132.228845 104.950499) (xy 132.383497 104.919737) (xy 132.529179 104.859394) - (xy 132.660289 104.771789) (xy 132.771789 104.660289) (xy 132.859394 104.529179) (xy 132.919737 104.383497) - (xy 132.9505 104.228842) (xy 132.9505 104.071158) (xy 132.9505 104.071155) (xy 132.950499 104.071153) - (xy 132.928422 103.960167) (xy 132.919737 103.916503) (xy 132.909484 103.89175) (xy 132.859397 103.770827) - (xy 132.85939 103.770814) (xy 132.801354 103.683957) (xy 132.771789 103.639711) (xy 132.771786 103.639707) - (xy 132.753232 103.621153) (xy 133.7995 103.621153) (xy 133.7995 103.778846) (xy 133.830261 103.933489) - (xy 133.830264 103.933501) (xy 133.890602 104.079172) (xy 133.890609 104.079185) (xy 133.97821 104.210288) - (xy 133.978213 104.210292) (xy 134.089707 104.321786) (xy 134.089711 104.321789) (xy 134.220814 104.40939) - (xy 134.220827 104.409397) (xy 134.336021 104.457111) (xy 134.366503 104.469737) (xy 134.455356 104.487411) - (xy 134.521153 104.500499) (xy 134.521156 104.5005) (xy 134.521158 104.5005) (xy 134.678844 104.5005) - (xy 134.678845 104.500499) (xy 134.833497 104.469737) (xy 134.882129 104.449592) (xy 134.951597 104.442124) - (xy 134.998472 104.461052) (xy 135.033452 104.484425) (xy 135.070821 104.509394) (xy 135.070823 104.509395) - (xy 135.070827 104.509397) (xy 135.216498 104.569735) (xy 135.216503 104.569737) (xy 135.274767 104.581326) - (xy 135.377132 104.601689) (xy 135.37665 104.604107) (xy 135.431395 104.626204) (xy 135.457568 104.654565) - (xy 135.52821 104.760288) (xy 135.528213 104.760292) (xy 135.639707 104.871786) (xy 135.639711 104.871789) - (xy 135.770814 104.95939) (xy 135.770827 104.959397) (xy 135.916498 105.019735) (xy 135.916503 105.019737) - (xy 136.071153 105.050499) (xy 136.071156 105.0505) (xy 136.071158 105.0505) (xy 136.228844 105.0505) - (xy 136.228845 105.050499) (xy 136.383497 105.019737) (xy 136.529179 104.959394) (xy 136.660289 104.871789) - (xy 136.771789 104.760289) (xy 136.859394 104.629179) (xy 136.859395 104.629176) (xy 136.859397 104.629173) - (xy 136.891201 104.552389) (xy 136.906149 104.5163) (xy 136.949989 104.461897) (xy 137.016283 104.439832) - (xy 137.083983 104.457111) (xy 137.131593 104.508248) (xy 137.135271 104.516299) (xy 137.140606 104.529179) - (xy 137.140609 104.529185) (xy 137.22821 104.660288) (xy 137.228213 104.660292) (xy 137.339707 104.771786) - (xy 137.339711 104.771789) (xy 137.470814 104.85939) (xy 137.470827 104.859397) (xy 137.608683 104.916498) - (xy 137.616503 104.919737) (xy 137.771153 104.950499) (xy 137.771156 104.9505) (xy 137.771158 104.9505) - (xy 137.928844 104.9505) (xy 137.928845 104.950499) (xy 138.083497 104.919737) (xy 138.229179 104.859394) - (xy 138.360289 104.771789) (xy 138.471789 104.660289) (xy 138.559394 104.529179) (xy 138.577932 104.484423) - (xy 138.621772 104.430021) (xy 138.688066 104.407955) (xy 138.739942 104.417314) (xy 138.866503 104.469737) - (xy 138.955356 104.487411) (xy 139.021153 104.500499) (xy 139.021156 104.5005) (xy 139.021158 104.5005) - (xy 139.178844 104.5005) (xy 139.178845 104.500499) (xy 139.333497 104.469737) (xy 139.479179 104.409394) - (xy 139.610289 104.321789) (xy 139.721789 104.210289) (xy 139.809394 104.079179) (xy 139.812719 104.071153) - (xy 139.85869 103.960167) (xy 139.869737 103.933497) (xy 139.9005 103.778842) (xy 139.9005 103.621158) - (xy 139.9005 103.621155) (xy 139.900499 103.621153) (xy 139.887162 103.554104) (xy 139.869737 103.466503) - (xy 139.859606 103.442044) (xy 139.809397 103.320827) (xy 139.80939 103.320814) (xy 139.721789 103.189711) - (xy 139.721786 103.189707) (xy 139.610289 103.07821) (xy 139.595259 103.068168) (xy 139.479185 102.990609) - (xy 139.479172 102.990602) (xy 139.432217 102.971153) (xy 141.9995 102.971153) (xy 141.9995 103.128846) - (xy 142.030261 103.283489) (xy 142.030264 103.283501) (xy 142.090602 103.429172) (xy 142.090609 103.429185) - (xy 142.17821 103.560288) (xy 142.178213 103.560292) (xy 142.289707 103.671786) (xy 142.289711 103.671789) - (xy 142.420814 103.75939) (xy 142.420827 103.759397) (xy 142.566498 103.819735) (xy 142.566503 103.819737) - (xy 142.671418 103.840606) (xy 142.721153 103.850499) (xy 142.721156 103.8505) (xy 142.721158 103.8505) - (xy 142.878844 103.8505) (xy 142.878845 103.850499) (xy 143.033497 103.819737) (xy 143.151592 103.770821) - (xy 143.179172 103.759397) (xy 143.179172 103.759396) (xy 143.179179 103.759394) (xy 143.310289 103.671789) - (xy 143.421789 103.560289) (xy 143.509394 103.429179) (xy 143.569737 103.283497) (xy 143.584719 103.208177) - (xy 143.59556 103.15368) (xy 143.627945 103.091769) (xy 143.669721 103.063311) (xy 143.679179 103.059394) - (xy 143.810289 102.971789) (xy 143.810925 102.971153) (xy 144.5995 102.971153) (xy 144.5995 103.128846) - (xy 144.630261 103.283489) (xy 144.630264 103.283501) (xy 144.690602 103.429172) (xy 144.690609 103.429185) - (xy 144.77821 103.560288) (xy 144.778213 103.560292) (xy 144.889707 103.671786) (xy 144.889711 103.671789) - (xy 145.020814 103.75939) (xy 145.020827 103.759397) (xy 145.166498 103.819735) (xy 145.166503 103.819737) - (xy 145.271418 103.840606) (xy 145.321153 103.850499) (xy 145.321156 103.8505) (xy 145.321158 103.8505) - (xy 145.478844 103.8505) (xy 145.478845 103.850499) (xy 145.633497 103.819737) (xy 145.751592 103.770821) - (xy 145.779172 103.759397) (xy 145.779172 103.759396) (xy 145.779179 103.759394) (xy 145.910289 103.671789) - (xy 146.021789 103.560289) (xy 146.109394 103.429179) (xy 146.169737 103.283497) (xy 146.2005 103.128842) - (xy 146.2005 102.971158) (xy 146.2005 102.971155) (xy 146.200499 102.971153) (xy 146.178447 102.860292) - (xy 146.169737 102.816503) (xy 146.133569 102.729185) (xy 146.109397 102.670827) (xy 146.10939 102.670814) - (xy 146.021789 102.539711) (xy 146.021786 102.539707) (xy 145.910292 102.428213) (xy 145.910288 102.42821) - (xy 145.779185 102.340609) (xy 145.779172 102.340602) (xy 145.633501 102.280264) (xy 145.633489 102.280261) - (xy 145.478845 102.2495) (xy 145.478842 102.2495) (xy 145.321158 102.2495) (xy 145.321155 102.2495) - (xy 145.16651 102.280261) (xy 145.166498 102.280264) (xy 145.020827 102.340602) (xy 145.020814 102.340609) - (xy 144.889711 102.42821) (xy 144.889707 102.428213) (xy 144.778213 102.539707) (xy 144.77821 102.539711) - (xy 144.690609 102.670814) (xy 144.690602 102.670827) (xy 144.630264 102.816498) (xy 144.630261 102.81651) - (xy 144.5995 102.971153) (xy 143.810925 102.971153) (xy 143.851817 102.930261) (xy 143.904694 102.877385) - (xy 143.921786 102.860292) (xy 143.921789 102.860289) (xy 144.009394 102.729179) (xy 144.069737 102.583497) - (xy 144.1005 102.428842) (xy 144.1005 102.271158) (xy 144.1005 102.271155) (xy 144.100499 102.271153) - (xy 144.069738 102.11651) (xy 144.069738 102.116508) (xy 144.069737 102.116503) (xy 144.069735 102.116498) - (xy 144.009397 101.970827) (xy 144.00939 101.970814) (xy 143.921789 101.839711) (xy 143.921786 101.839707) - (xy 143.810292 101.728213) (xy 143.810288 101.72821) (xy 143.679185 101.640609) (xy 143.679172 101.640602) - (xy 143.533501 101.580264) (xy 143.533489 101.580261) (xy 143.378845 101.5495) (xy 143.378842 101.5495) - (xy 143.221158 101.5495) (xy 143.221155 101.5495) (xy 143.06651 101.580261) (xy 143.066498 101.580264) - (xy 142.920827 101.640602) (xy 142.920814 101.640609) (xy 142.789711 101.72821) (xy 142.789707 101.728213) - (xy 142.678213 101.839707) (xy 142.67821 101.839711) (xy 142.590609 101.970814) (xy 142.590602 101.970827) - (xy 142.530264 102.116498) (xy 142.530261 102.116508) (xy 142.50444 102.24632) (xy 142.472055 102.308231) - (xy 142.430278 102.336688) (xy 142.420826 102.340603) (xy 142.420814 102.340609) (xy 142.289711 102.42821) - (xy 142.289707 102.428213) (xy 142.178213 102.539707) (xy 142.17821 102.539711) (xy 142.090609 102.670814) - (xy 142.090602 102.670827) (xy 142.030264 102.816498) (xy 142.030261 102.81651) (xy 141.9995 102.971153) - (xy 139.432217 102.971153) (xy 139.333501 102.930264) (xy 139.333489 102.930261) (xy 139.178845 102.8995) - (xy 139.178842 102.8995) (xy 139.021158 102.8995) (xy 139.021155 102.8995) (xy 138.86651 102.930261) - (xy 138.866498 102.930264) (xy 138.720827 102.990602) (xy 138.720814 102.990609) (xy 138.589711 103.07821) - (xy 138.589707 103.078213) (xy 138.478213 103.189707) (xy 138.47821 103.189711) (xy 138.390609 103.320814) - (xy 138.390606 103.320821) (xy 138.372067 103.365577) (xy 138.328225 103.41998) (xy 138.26193 103.442044) - (xy 138.210054 103.432684) (xy 138.083501 103.380264) (xy 138.083489 103.380261) (xy 137.928845 103.3495) - (xy 137.928842 103.3495) (xy 137.771158 103.3495) (xy 137.771155 103.3495) (xy 137.61651 103.380261) - (xy 137.616498 103.380264) (xy 137.470827 103.440602) (xy 137.470814 103.440609) (xy 137.339711 103.52821) - (xy 137.339707 103.528213) (xy 137.228213 103.639707) (xy 137.22821 103.639711) (xy 137.140609 103.770814) - (xy 137.140604 103.770824) (xy 137.09385 103.883699) (xy 137.050009 103.938102) (xy 136.983715 103.960167) - (xy 136.916015 103.942888) (xy 136.868405 103.89175) (xy 136.864727 103.883696) (xy 136.859395 103.870824) - (xy 136.859394 103.870821) (xy 136.859392 103.870818) (xy 136.85939 103.870814) (xy 136.771789 103.739711) - (xy 136.771786 103.739707) (xy 136.660292 103.628213) (xy 136.660288 103.62821) (xy 136.529185 103.540609) - (xy 136.529172 103.540602) (xy 136.383501 103.480264) (xy 136.383489 103.480261) (xy 136.222868 103.448311) - (xy 136.223346 103.445906) (xy 136.168547 103.42375) (xy 136.142431 103.395434) (xy 136.071789 103.28971) - (xy 135.960292 103.178213) (xy 135.960287 103.178209) (xy 135.829185 103.090609) (xy 135.829172 103.090602) - (xy 135.683501 103.030264) (xy 135.683489 103.030261) (xy 135.528845 102.9995) (xy 135.528842 102.9995) - (xy 135.371158 102.9995) (xy 135.371155 102.9995) (xy 135.216505 103.030261) (xy 135.16787 103.050407) - (xy 135.0984 103.057875) (xy 135.051527 103.038947) (xy 134.979185 102.990609) (xy 134.979172 102.990602) - (xy 134.833501 102.930264) (xy 134.833489 102.930261) (xy 134.678845 102.8995) (xy 134.678842 102.8995) - (xy 134.521158 102.8995) (xy 134.521155 102.8995) (xy 134.36651 102.930261) (xy 134.366498 102.930264) - (xy 134.220827 102.990602) (xy 134.220814 102.990609) (xy 134.089711 103.07821) (xy 134.089707 103.078213) - (xy 133.978213 103.189707) (xy 133.97821 103.189711) (xy 133.890609 103.320814) (xy 133.890602 103.320827) - (xy 133.830264 103.466498) (xy 133.830261 103.46651) (xy 133.7995 103.621153) (xy 132.753232 103.621153) - (xy 132.660292 103.528213) (xy 132.660288 103.52821) (xy 132.529185 103.440609) (xy 132.529172 103.440602) - (xy 132.383501 103.380264) (xy 132.383489 103.380261) (xy 132.228845 103.3495) (xy 132.228842 103.3495) - (xy 132.071158 103.3495) (xy 132.071155 103.3495) (xy 131.91651 103.380261) (xy 131.916498 103.380264) - (xy 131.770827 103.440602) (xy 131.770814 103.440609) (xy 131.639711 103.52821) (xy 131.639707 103.528213) - (xy 131.528213 103.639707) (xy 131.52821 103.639711) (xy 131.477601 103.715453) (xy 131.423989 103.760258) - (xy 131.354664 103.768965) (xy 131.291636 103.73881) (xy 131.254917 103.679367) (xy 131.250499 103.646562) - (xy 131.250499 103.621155) (xy 131.250498 103.621153) (xy 131.237161 103.554104) (xy 131.219736 103.466503) - (xy 131.177285 103.364018) (xy 131.169817 103.29455) (xy 131.201092 103.232071) (xy 131.229848 103.209179) - (xy 131.231582 103.208177) (xy 131.231585 103.208177) (xy 131.283487 103.178211) (xy 131.368516 103.12912) - (xy 131.48032 103.017316) (xy 131.48032 103.017314) (xy 131.490524 103.007111) (xy 131.490527 103.007106) - (xy 133.565494 100.932141) (xy 133.626814 100.898658) (xy 133.696506 100.903642) (xy 133.752439 100.945514) - (xy 133.776856 101.010978) (xy 133.774789 101.044015) (xy 133.7495 101.171153) (xy 133.7495 101.328846) - (xy 133.780261 101.483489) (xy 133.780264 101.483501) (xy 133.840602 101.629172) (xy 133.840609 101.629185) - (xy 133.92821 101.760288) (xy 133.928213 101.760292) (xy 134.039707 101.871786) (xy 134.039711 101.871789) - (xy 134.170814 101.95939) (xy 134.170827 101.959397) (xy 134.309171 102.0167) (xy 134.316503 102.019737) - (xy 134.471153 102.050499) (xy 134.471156 102.0505) (xy 134.471158 102.0505) (xy 134.628844 102.0505) - (xy 134.628845 102.050499) (xy 134.783497 102.019737) (xy 134.901592 101.970821) (xy 134.929172 101.959397) - (xy 134.929172 101.959396) (xy 134.929179 101.959394) (xy 135.060289 101.871789) (xy 135.171789 101.760289) - (xy 135.193222 101.728213) (xy 135.196898 101.722712) (xy 135.25051 101.677906) (xy 135.319835 101.669199) - (xy 135.382862 101.699353) (xy 135.403102 101.722712) (xy 135.428207 101.760284) (xy 135.428213 101.760292) - (xy 135.539707 101.871786) (xy 135.539711 101.871789) (xy 135.670814 101.95939) (xy 135.670827 101.959397) - (xy 135.809171 102.0167) (xy 135.816503 102.019737) (xy 135.971153 102.050499) (xy 135.971156 102.0505) - (xy 135.971158 102.0505) (xy 136.128844 102.0505) (xy 136.128845 102.050499) (xy 136.283497 102.019737) - (xy 136.401592 101.970821) (xy 136.429172 101.959397) (xy 136.429172 101.959396) (xy 136.429179 101.959394) - (xy 136.560289 101.871789) (xy 136.671789 101.760289) (xy 136.759394 101.629179) (xy 136.819737 101.483497) - (xy 136.8505 101.328842) (xy 136.8505 101.171158) (xy 136.8505 101.171155) (xy 136.847453 101.155841) - (xy 136.853677 101.08625) (xy 136.896538 101.03107) (xy 136.900127 101.028578) (xy 136.910289 101.021789) - (xy 137.021789 100.910289) (xy 137.109394 100.779179) (xy 137.169737 100.633497) (xy 137.2005 100.478842) - (xy 137.2005 100.321158) (xy 137.2005 100.321155) (xy 137.184017 100.238292) (xy 137.190244 100.1687) - (xy 137.233107 100.113523) (xy 137.298996 100.090278) (xy 137.305634 100.0901) (xy 138.2848 100.0901) - (xy 138.351839 100.109785) (xy 138.397594 100.162589) (xy 138.4088 100.2141) (xy 138.4088 100.263146) - (xy 138.439561 100.417789) (xy 138.439564 100.417801) (xy 138.499902 100.563472) (xy 138.499909 100.563485) - (xy 138.58751 100.694588) (xy 138.587513 100.694592) (xy 138.699007 100.806086) (xy 138.699011 100.806089) - (xy 138.830114 100.89369) (xy 138.830127 100.893697) (xy 138.975798 100.954035) (xy 138.975803 100.954037) - (xy 139.130453 100.984799) (xy 139.130456 100.9848) (xy 139.130458 100.9848) (xy 139.288144 100.9848) - (xy 139.288145 100.984799) (xy 139.442797 100.954037) (xy 139.588479 100.893694) (xy 139.719589 100.806089) - (xy 139.831089 100.694589) (xy 139.918694 100.563479) (xy 139.979037 100.417797) (xy 140.0098 100.263142) - (xy 140.0098 100.2141) (xy 140.029485 100.147061) (xy 140.082289 100.101306) (xy 140.1338 100.0901) - (xy 143.921631 100.0901) (xy 143.921647 100.090101) (xy 143.929243 100.090101) (xy 144.087354 100.090101) - (xy 144.087357 100.090101) (xy 144.240085 100.049177) (xy 144.322097 100.001827) (xy 144.377016 99.97012) - (xy 144.48882 99.858316) (xy 144.48882 99.858314) (xy 144.499024 99.848111) (xy 144.499027 99.848106) - (xy 145.467562 98.879572) (xy 145.528883 98.846089) (xy 145.53105 98.845638) (xy 145.588985 98.834113) - (xy 145.686397 98.814737) (xy 145.832079 98.754394) (xy 145.963189 98.666789) (xy 145.963192 98.666786) - (xy 146.033991 98.595988) (xy 146.095314 98.562503) (xy 146.165006 98.567487) (xy 146.209353 98.595988) - (xy 147.775681 100.162316) (xy 147.809166 100.223639) (xy 147.812 100.249997) (xy 147.812 101.454729) - (xy 147.792315 101.521768) (xy 147.739511 101.567523) (xy 147.670353 101.577467) (xy 147.663809 101.576346) - (xy 147.528845 101.5495) (xy 147.528842 101.5495) (xy 147.371158 101.5495) (xy 147.371155 101.5495) - (xy 147.21651 101.580261) (xy 147.216498 101.580264) (xy 147.070827 101.640602) (xy 147.070814 101.640609) - (xy 146.939711 101.72821) (xy 146.939707 101.728213) (xy 146.828213 101.839707) (xy 146.82821 101.839711) - (xy 146.740609 101.970814) (xy 146.740602 101.970827) (xy 146.680264 102.116498) (xy 146.680261 102.11651) - (xy 146.6495 102.271153) (xy 146.6495 102.428846) (xy 146.680261 102.583489) (xy 146.680264 102.583501) - (xy 146.740602 102.729172) (xy 146.740609 102.729185) (xy 146.82821 102.860288) (xy 146.828213 102.860292) - (xy 146.939707 102.971786) (xy 146.939711 102.971789) (xy 147.070814 103.05939) (xy 147.070827 103.059397) - (xy 147.149498 103.091983) (xy 147.216503 103.119737) (xy 147.371153 103.150499) (xy 147.371156 103.1505) - (xy 147.371158 103.1505) (xy 147.528844 103.1505) (xy 147.59514 103.137312) (xy 147.663809 103.123653) - (xy 147.7334 103.12988) (xy 147.788577 103.172742) (xy 147.811822 103.238632) (xy 147.812 103.24527) - (xy 147.812 105.554729) (xy 147.792315 105.621768) (xy 147.739511 105.667523) (xy 147.670353 105.677467) - (xy 147.663809 105.676346) (xy 147.528845 105.6495) (xy 147.528842 105.6495) (xy 147.371158 105.6495) - (xy 147.371155 105.6495) (xy 147.21651 105.680261) (xy 147.216498 105.680264) (xy 147.070827 105.740602) - (xy 147.070814 105.740609) (xy 146.939711 105.82821) (xy 146.939707 105.828213) (xy 146.828213 105.939707) - (xy 146.82821 105.939711) (xy 146.740609 106.070814) (xy 146.740602 106.070827) (xy 146.680264 106.216498) - (xy 146.680261 106.21651) (xy 146.6495 106.371153) (xy 146.6495 106.528846) (xy 146.680261 106.683489) - (xy 146.680264 106.683501) (xy 146.740602 106.829172) (xy 146.740609 106.829185) (xy 146.82821 106.960288) - (xy 146.828213 106.960292) (xy 146.939707 107.071786) (xy 146.939711 107.071789) (xy 147.070814 107.15939) - (xy 147.070827 107.159397) (xy 147.216498 107.219735) (xy 147.216503 107.219737) (xy 147.341065 107.244514) - (xy 147.371153 107.250499) (xy 147.371156 107.2505) (xy 147.371158 107.2505) (xy 147.528844 107.2505) - (xy 147.59514 107.237312) (xy 147.663809 107.223653) (xy 147.7334 107.22988) (xy 147.788577 107.272742) - (xy 147.811822 107.338632) (xy 147.812 107.34527) (xy 147.812 108.907621) (xy 147.792315 108.97466) - (xy 147.739511 109.020415) (xy 147.670353 109.030359) (xy 147.640548 109.022182) (xy 147.533549 108.977862) - (xy 147.533542 108.97786) (xy 147.53354 108.977859) (xy 147.533534 108.977858) (xy 147.389459 108.9492) - (xy 147.389455 108.9492) (xy 147.242545 108.9492) (xy 147.24254 108.9492) (xy 147.098465 108.977858) - (xy 147.098455 108.977861) (xy 146.962733 109.034078) (xy 146.962724 109.034083) (xy 146.84058 109.115698) - (xy 146.840576 109.115701) (xy 146.736701 109.219576) (xy 146.736698 109.21958) (xy 146.655083 109.341724) - (xy 146.655078 109.341733) (xy 146.598861 109.477455) (xy 146.598858 109.477465) (xy 146.5702 109.62154) - (xy 146.5702 109.768459) (xy 146.598858 109.912534) (xy 146.598861 109.912544) (xy 146.655078 110.048266) - (xy 146.655083 110.048275) (xy 146.736698 110.170419) (xy 146.736701 110.170423) (xy 146.840576 110.274298) - (xy 146.84058 110.274301) (xy 146.962724 110.355916) (xy 146.962733 110.355921) (xy 146.9878 110.366304) - (xy 147.098458 110.41214) (xy 147.24254 110.440799) (xy 147.242544 110.4408) (xy 147.242545 110.4408) - (xy 147.389456 110.4408) (xy 147.389457 110.440799) (xy 147.533542 110.41214) (xy 147.640547 110.367816) - (xy 147.710017 110.360348) (xy 147.772496 110.391623) (xy 147.808148 110.451712) (xy 147.812 110.482378) - (xy 147.812 111.000968) (xy 147.792315 111.068007) (xy 147.739511 111.113762) (xy 147.735455 111.115528) - (xy 147.693026 111.133103) (xy 147.693014 111.133109) (xy 147.561911 111.22071) (xy 147.561907 111.220713) - (xy 147.450413 111.332207) (xy 147.45041 111.332211) (xy 147.362809 111.463314) (xy 147.362802 111.463327) - (xy 147.302464 111.608998) (xy 147.302461 111.60901) (xy 147.2717 111.763653) (xy 147.2717 111.921346) - (xy 147.302461 112.075989) (xy 147.302464 112.076001) (xy 147.362802 112.221672) (xy 147.362809 112.221685) - (xy 147.45041 112.352788) (xy 147.450413 112.352792) (xy 147.561907 112.464286) (xy 147.561911 112.464289) - (xy 147.693014 112.55189) (xy 147.693027 112.551897) (xy 147.838698 112.612235) (xy 147.838703 112.612237) - (xy 147.993353 112.642999) (xy 147.993356 112.643) (xy 147.993358 112.643) (xy 148.151044 112.643) - (xy 148.151045 112.642999) (xy 148.305697 112.612237) (xy 148.451379 112.551894) (xy 148.582489 112.464289) - (xy 148.693989 112.352789) (xy 148.781594 112.221679) (xy 148.841937 112.075997) (xy 148.8727 111.921342) - (xy 148.8727 111.921341) (xy 148.873489 111.917375) (xy 148.890861 111.879054) (xy 148.888956 111.877955) - (xy 148.89302 111.870916) (xy 148.955069 111.763443) (xy 148.972077 111.733985) (xy 149.013001 111.581257) - (xy 149.013001 111.423143) (xy 149.013001 111.415548) (xy 149.013 111.41553) (xy 149.013 100.03896) - (xy 149.013001 100.038947) (xy 149.013001 99.870844) (xy 149.009644 99.858316) (xy 148.972077 99.718116) - (xy 148.921356 99.630263) (xy 148.893024 99.58119) (xy 148.893018 99.581182) (xy 147.867125 98.555289) - (xy 146.825815 97.51398) (xy 146.792331 97.452658) (xy 146.797315 97.382966) (xy 146.839187 97.327033) - (xy 146.904651 97.302616) (xy 146.913497 97.3023) (xy 148.793384 97.3023) + (xy 139.353719 124.327863) (xy 139.316975 124.464998) (xy 139.3145 124.474234) (xy 137.678266 124.474234) + (xy 137.621789 124.389711) (xy 137.621786 124.389707) (xy 137.510292 124.278213) (xy 137.510288 124.27821) + (xy 137.379185 124.190609) (xy 137.379172 124.190602) (xy 137.233501 124.130264) (xy 137.233489 124.130261) + (xy 137.078845 124.0995) (xy 137.078842 124.0995) (xy 136.921158 124.0995) (xy 136.921155 124.0995) + (xy 136.76651 124.130261) (xy 136.766498 124.130264) (xy 136.620827 124.190602) (xy 136.620814 124.190609) + (xy 136.489711 124.27821) (xy 136.489707 124.278213) (xy 136.378213 124.389707) (xy 136.37821 124.389711) + (xy 136.290609 124.520814) (xy 136.290602 124.520827) (xy 136.230264 124.666498) (xy 136.230261 124.66651) + (xy 136.1995 124.821153) (xy 134.61798 124.821153) (xy 134.646281 124.772135) (xy 134.6855 124.625766) + (xy 134.6855 124.474234) (xy 134.646281 124.327865) (xy 134.570515 124.196635) (xy 134.463365 124.089485) + (xy 134.385162 124.044334) (xy 134.332136 124.013719) (xy 134.227584 123.985705) (xy 134.185766 123.9745) + (xy 134.034234 123.9745) (xy 133.887862 124.013719) (xy 133.866499 124.026054) (xy 133.798598 124.042525) + (xy 133.732572 124.019673) (xy 133.689382 123.964751) (xy 133.6805 123.918666) (xy 133.6805 123.371456) + (xy 133.642052 123.17817) (xy 133.642051 123.178169) (xy 133.642051 123.178165) (xy 133.612511 123.106849) + (xy 133.566635 122.996092) (xy 133.566628 122.996079) (xy 133.457139 122.832218) (xy 133.457136 122.832214) + (xy 133.317785 122.692863) (xy 133.317781 122.69286) (xy 133.15392 122.583371) (xy 133.153907 122.583364) + (xy 132.971839 122.50795) (xy 132.971829 122.507947) (xy 132.778543 122.4695) (xy 132.778541 122.4695) + (xy 132.581459 122.4695) (xy 132.581457 122.4695) (xy 132.38817 122.507947) (xy 132.38816 122.50795) + (xy 132.206092 122.583364) (xy 132.206079 122.583371) (xy 132.042218 122.69286) (xy 132.042214 122.692863) + (xy 131.902863 122.832214) (xy 131.90286 122.832218) (xy 131.793371 122.996079) (xy 131.793364 122.996092) + (xy 131.71795 123.17816) (xy 131.717947 123.17817) (xy 131.6795 123.371456) (xy 131.6795 123.371459) + (xy 131.6795 124.668541) (xy 131.6795 124.668543) (xy 131.679499 124.668543) (xy 123.100622 124.668543) + (xy 123.010292 124.578213) (xy 123.010288 124.57821) (xy 122.879185 124.490609) (xy 122.879172 124.490602) + (xy 122.733499 124.430263) (xy 122.733493 124.430261) (xy 122.693816 124.422369) (xy 122.631906 124.389983) + (xy 122.603448 124.348204) (xy 122.584138 124.301585) (xy 122.584131 124.301572) (xy 122.49653 124.170469) + (xy 122.496527 124.170465) (xy 122.385033 124.058971) (xy 122.385029 124.058968) (xy 122.253926 123.971367) + (xy 122.253913 123.97136) (xy 122.108242 123.911022) (xy 122.10823 123.911019) (xy 121.953586 123.880258) + (xy 121.953583 123.880258) (xy 121.795899 123.880258) (xy 121.795896 123.880258) (xy 121.641251 123.911019) + (xy 121.641239 123.911022) (xy 121.495568 123.97136) (xy 121.495555 123.971367) (xy 121.364455 124.058966) + (xy 121.364446 124.058973) (xy 121.363216 124.060204) (xy 121.362414 124.060641) (xy 121.359748 124.06283) + (xy 121.359332 124.062324) (xy 121.30189 124.093684) (xy 121.251353 124.094133) (xy 121.226188 124.089127) + (xy 121.178842 124.07971) (xy 121.021158 124.07971) (xy 121.021155 124.07971) (xy 120.86651 124.110471) + (xy 120.866498 124.110474) (xy 120.720827 124.170812) (xy 120.720814 124.170819) (xy 120.589711 124.25842) + (xy 120.589707 124.258423) (xy 120.478213 124.369917) (xy 120.478206 124.369926) (xy 120.477597 124.370838) + (xy 120.477155 124.371207) (xy 120.474347 124.374629) (xy 120.473697 124.374096) (xy 120.423982 124.415639) + (xy 120.354656 124.424342) (xy 120.291631 124.394183) (xy 120.254916 124.334737) (xy 120.2505 124.30194) + (xy 120.2505 122.393713) (xy 121.6495 122.393713) (xy 121.6495 122.606287) (xy 121.653406 122.630948) + (xy 121.671906 122.747756) (xy 121.682754 122.816243) (xy 121.739409 122.990609) (xy 121.748444 123.018414) + (xy 121.844951 123.20782) (xy 121.96989 123.379786) (xy 122.120213 123.530109) (xy 122.292179 123.655048) + (xy 122.292181 123.655049) (xy 122.292184 123.655051) (xy 122.481588 123.751557) (xy 122.683757 123.817246) + (xy 122.893713 123.8505) (xy 122.893714 123.8505) (xy 123.106286 123.8505) (xy 123.106287 123.8505) + (xy 123.316243 123.817246) (xy 123.518412 123.751557) (xy 123.707816 123.655051) (xy 123.754473 123.621153) + (xy 123.879786 123.530109) (xy 123.879788 123.530106) (xy 123.879792 123.530104) (xy 124.030104 123.379792) + (xy 124.030106 123.379788) (xy 124.030109 123.379786) (xy 124.116053 123.261492) (xy 125.201698 123.261492) + (xy 125.201698 123.419185) (xy 125.232459 123.573828) (xy 125.232462 123.57384) (xy 125.2928 123.719511) + (xy 125.292807 123.719524) (xy 125.380408 123.850627) (xy 125.380411 123.850631) (xy 125.491905 123.962125) + (xy 125.491909 123.962128) (xy 125.623012 124.049729) (xy 125.623025 124.049736) (xy 125.743168 124.0995) + (xy 125.768701 124.110076) (xy 125.923351 124.140838) (xy 125.923354 124.140839) (xy 125.923356 124.140839) + (xy 126.081042 124.140839) (xy 126.081043 124.140838) (xy 126.235695 124.110076) (xy 126.259899 124.100049) + (xy 126.329368 124.092581) (xy 126.386016 124.118757) (xy 126.389711 124.121789) (xy 126.520814 124.20939) + (xy 126.520827 124.209397) (xy 126.639188 124.258423) (xy 126.666503 124.269737) (xy 126.821153 124.300499) + (xy 126.821156 124.3005) (xy 126.821158 124.3005) (xy 126.978844 124.3005) (xy 126.978845 124.300499) + (xy 127.133497 124.269737) (xy 127.279179 124.209394) (xy 127.410289 124.121789) (xy 127.521789 124.010289) + (xy 127.609394 123.879179) (xy 127.609967 123.877797) (xy 127.650954 123.778844) (xy 127.669737 123.733497) + (xy 127.692083 123.621158) (xy 127.692084 123.621153) (xy 128.3995 123.621153) (xy 128.3995 123.778846) + (xy 128.430261 123.933489) (xy 128.430264 123.933501) (xy 128.490602 124.079172) (xy 128.490609 124.079185) + (xy 128.57821 124.210288) (xy 128.578213 124.210292) (xy 128.689707 124.321786) (xy 128.689711 124.321789) + (xy 128.820814 124.40939) (xy 128.820827 124.409397) (xy 128.914995 124.448402) (xy 128.966503 124.469737) + (xy 129.121153 124.500499) (xy 129.121156 124.5005) (xy 129.121158 124.5005) (xy 129.278844 124.5005) + (xy 129.278845 124.500499) (xy 129.433497 124.469737) (xy 129.57817 124.409812) (xy 129.579172 124.409397) + (xy 129.579172 124.409396) (xy 129.579179 124.409394) (xy 129.710289 124.321789) (xy 129.821789 124.210289) + (xy 129.909394 124.079179) (xy 129.921593 124.049729) (xy 129.956791 123.964751) (xy 129.969737 123.933497) + (xy 130.0005 123.778842) (xy 130.0005 123.621158) (xy 130.0005 123.621155) (xy 130.000499 123.621153) + (xy 129.969738 123.46651) (xy 129.969737 123.466503) (xy 129.950955 123.421158) (xy 129.947501 123.412819) + (xy 129.909397 123.320827) (xy 129.90939 123.320814) (xy 129.821789 123.189711) (xy 129.821786 123.189707) + (xy 129.710292 123.078213) (xy 129.710288 123.07821) (xy 129.579185 122.990609) (xy 129.579172 122.990602) + (xy 129.433501 122.930264) (xy 129.433489 122.930261) (xy 129.278845 122.8995) (xy 129.278842 122.8995) + (xy 129.121158 122.8995) (xy 129.121155 122.8995) (xy 128.96651 122.930261) (xy 128.966498 122.930264) + (xy 128.820827 122.990602) (xy 128.820814 122.990609) (xy 128.689711 123.07821) (xy 128.689707 123.078213) + (xy 128.578213 123.189707) (xy 128.57821 123.189711) (xy 128.490609 123.320814) (xy 128.490602 123.320827) + (xy 128.430264 123.466498) (xy 128.430261 123.46651) (xy 128.3995 123.621153) (xy 127.692084 123.621153) + (xy 127.698107 123.590875) (xy 127.698107 123.590874) (xy 127.7005 123.578844) (xy 127.7005 123.421155) + (xy 127.700499 123.421153) (xy 127.692272 123.379792) (xy 127.669737 123.266503) (xy 127.669735 123.266498) + (xy 127.609397 123.120827) (xy 127.60939 123.120814) (xy 127.521789 122.989711) (xy 127.521786 122.989707) + (xy 127.410292 122.878213) (xy 127.410288 122.87821) (xy 127.279185 122.790609) (xy 127.279172 122.790602) + (xy 127.133501 122.730264) (xy 127.133489 122.730261) (xy 126.978845 122.6995) (xy 126.978842 122.6995) + (xy 126.821158 122.6995) (xy 126.821155 122.6995) (xy 126.666511 122.73026) (xy 126.666498 122.730264) + (xy 126.642292 122.74029) (xy 126.572823 122.747756) (xy 126.516183 122.721582) (xy 126.512491 122.718552) + (xy 126.381383 122.630948) (xy 126.38137 122.630941) (xy 126.235699 122.570603) (xy 126.235687 122.5706) + (xy 126.081043 122.539839) (xy 126.08104 122.539839) (xy 125.923356 122.539839) (xy 125.923353 122.539839) + (xy 125.768708 122.5706) (xy 125.768696 122.570603) (xy 125.623025 122.630941) (xy 125.623012 122.630948) + (xy 125.491909 122.718549) (xy 125.491905 122.718552) (xy 125.380411 122.830046) (xy 125.380408 122.83005) + (xy 125.292807 122.961153) (xy 125.2928 122.961166) (xy 125.232462 123.106837) (xy 125.232459 123.106849) + (xy 125.201698 123.261492) (xy 124.116053 123.261492) (xy 124.15505 123.207817) (xy 124.159488 123.199109) + (xy 124.206502 123.106837) (xy 124.251557 123.018412) (xy 124.317246 122.816243) (xy 124.3505 122.606287) + (xy 124.3505 122.424983) (xy 144.0995 122.424983) (xy 144.0995 123.775001) (xy 144.099501 123.775018) + (xy 144.11 123.877796) (xy 144.110001 123.877799) (xy 144.165185 124.044331) (xy 144.165187 124.044336) + (xy 144.184324 124.075362) (xy 144.257288 124.193656) (xy 144.381344 124.317712) (xy 144.530666 124.409814) + (xy 144.697203 124.464999) (xy 144.799991 124.4755) (xy 145.600008 124.475499) (xy 145.600016 124.475498) + (xy 145.600019 124.475498) (xy 145.656434 124.469735) (xy 145.702797 124.464999) (xy 145.869334 124.409814) + (xy 146.018656 124.317712) (xy 146.142712 124.193656) (xy 146.18231 124.129456) (xy 146.234258 124.082732) + (xy 146.30322 124.071509) (xy 146.367303 124.099352) (xy 146.37553 124.106872) (xy 146.483072 124.214414) + (xy 146.623212 124.316232) (xy 146.777555 124.394873) (xy 146.942299 124.448402) (xy 147.113389 124.4755) + (xy 147.11339 124.4755) (xy 147.28661 124.4755) (xy 147.286611 124.4755) (xy 147.457701 124.448402) + (xy 147.622445 124.394873) (xy 147.776788 124.316232) (xy 147.916928 124.214414) (xy 148.039414 124.091928) + (xy 148.141232 123.951788) (xy 148.219873 123.797445) (xy 148.273402 123.632701) (xy 148.3005 123.461611) + (xy 148.3005 122.738389) (xy 148.273402 122.567299) (xy 148.219873 122.402555) (xy 148.141232 122.248212) + (xy 148.039414 122.108072) (xy 147.916928 121.985586) (xy 147.776788 121.883768) (xy 147.622445 121.805127) + (xy 147.457701 121.751598) (xy 147.457699 121.751597) (xy 147.457698 121.751597) (xy 147.326271 121.730781) + (xy 147.286611 121.7245) (xy 147.113389 121.7245) (xy 147.073728 121.730781) (xy 146.942302 121.751597) + (xy 146.777552 121.805128) (xy 146.623211 121.883768) (xy 146.483073 121.985585) (xy 146.37553 122.093128) + (xy 146.314207 122.126612) (xy 146.244515 122.121628) (xy 146.188582 122.079756) (xy 146.18231 122.070543) + (xy 146.142712 122.006344) (xy 146.018656 121.882288) (xy 145.893559 121.805128) (xy 145.869336 121.790187) + (xy 145.869331 121.790185) (xy 145.867862 121.789698) (xy 145.702797 121.735001) (xy 145.702795 121.735) + (xy 145.60001 121.7245) (xy 144.799998 121.7245) (xy 144.79998 121.724501) (xy 144.697203 121.735) + (xy 144.6972 121.735001) (xy 144.530668 121.790185) (xy 144.530663 121.790187) (xy 144.381342 121.882289) + (xy 144.257289 122.006342) (xy 144.165187 122.155663) (xy 144.165185 122.155668) (xy 144.137349 122.23967) + (xy 144.110001 122.322203) (xy 144.110001 122.322204) (xy 144.11 122.322204) (xy 144.0995 122.424983) + (xy 124.3505 122.424983) (xy 124.3505 122.393713) (xy 124.317246 122.183757) (xy 124.251557 121.981588) + (xy 124.155051 121.792184) (xy 124.155049 121.792181) (xy 124.155048 121.792179) (xy 124.030109 121.620213) + (xy 123.879786 121.46989) (xy 123.70782 121.344951) (xy 123.518414 121.248444) (xy 123.518413 121.248443) + (xy 123.518412 121.248443) (xy 123.316243 121.182754) (xy 123.316241 121.182753) (xy 123.31624 121.182753) + (xy 123.154957 121.157208) (xy 123.106287 121.1495) (xy 122.893713 121.1495) (xy 122.845042 121.157208) + (xy 122.68376 121.182753) (xy 122.481585 121.248444) (xy 122.292179 121.344951) (xy 122.120213 121.46989) + (xy 121.96989 121.620213) (xy 121.844951 121.792179) (xy 121.748444 121.981585) (xy 121.682753 122.18376) + (xy 121.67355 122.241866) (xy 121.6495 122.393713) (xy 120.2505 122.393713) (xy 120.2505 120.611152) + (xy 129.379498 120.611152) (xy 129.379498 120.768845) (xy 129.410259 120.923488) (xy 129.410262 120.9235) + (xy 129.4706 121.069171) (xy 129.470607 121.069184) (xy 129.558208 121.200287) (xy 129.558211 121.200291) + (xy 129.669705 121.311785) (xy 129.669709 121.311788) (xy 129.800812 121.399389) (xy 129.800825 121.399396) + (xy 129.946496 121.459734) (xy 129.946501 121.459736) (xy 130.101151 121.490498) (xy 130.101154 121.490499) + (xy 130.101156 121.490499) (xy 130.258842 121.490499) (xy 130.258843 121.490498) (xy 130.413495 121.459736) + (xy 130.559177 121.399393) (xy 130.690287 121.311788) (xy 130.801787 121.200288) (xy 130.889392 121.069178) + (xy 130.949735 120.923496) (xy 130.980498 120.768841) (xy 130.980498 120.611157) (xy 130.980498 120.611154) + (xy 130.980497 120.611152) (xy 130.949736 120.456509) (xy 130.949735 120.456502) (xy 130.949733 120.456497) + (xy 130.889395 120.310826) (xy 130.889388 120.310813) (xy 130.801787 120.17971) (xy 130.801784 120.179706) + (xy 130.69029 120.068212) (xy 130.690286 120.068209) (xy 130.559183 119.980608) (xy 130.55917 119.980601) + (xy 130.413499 119.920263) (xy 130.413487 119.92026) (xy 130.258843 119.889499) (xy 130.25884 119.889499) + (xy 130.101156 119.889499) (xy 130.101153 119.889499) (xy 129.946508 119.92026) (xy 129.946496 119.920263) + (xy 129.800825 119.980601) (xy 129.800812 119.980608) (xy 129.669709 120.068209) (xy 129.669705 120.068212) + (xy 129.558211 120.179706) (xy 129.558208 120.17971) (xy 129.470607 120.310813) (xy 129.4706 120.310826) + (xy 129.410262 120.456497) (xy 129.410259 120.456509) (xy 129.379498 120.611152) (xy 120.2505 120.611152) + (xy 120.2505 119.521153) (xy 123.1995 119.521153) (xy 123.1995 119.678846) (xy 123.230261 119.833489) + (xy 123.230264 119.833501) (xy 123.290602 119.979172) (xy 123.290609 119.979185) (xy 123.37821 120.110288) + (xy 123.378213 120.110292) (xy 123.489707 120.221786) (xy 123.489711 120.221789) (xy 123.620814 120.30939) + (xy 123.620827 120.309397) (xy 123.766498 120.369735) (xy 123.766503 120.369737) (xy 123.921153 120.400499) + (xy 123.921156 120.4005) (xy 123.921158 120.4005) (xy 124.078844 120.4005) (xy 124.078845 120.400499) + (xy 124.233497 120.369737) (xy 124.375722 120.310826) (xy 124.379172 120.309397) (xy 124.379172 120.309396) + (xy 124.379179 120.309394) (xy 124.510289 120.221789) (xy 124.621789 120.110289) (xy 124.709394 119.979179) + (xy 124.769737 119.833497) (xy 124.8005 119.678842) (xy 124.8005 119.521158) (xy 124.8005 119.521155) + (xy 124.800499 119.521153) (xy 124.778269 119.409397) (xy 124.769737 119.366503) (xy 124.744284 119.305053) + (xy 124.709397 119.220827) (xy 124.70939 119.220814) (xy 124.621789 119.089711) (xy 124.621786 119.089707) + (xy 124.510292 118.978213) (xy 124.510288 118.97821) (xy 124.379185 118.890609) (xy 124.379172 118.890602) + (xy 124.233501 118.830264) (xy 124.233489 118.830261) (xy 124.078845 118.7995) (xy 124.078842 118.7995) + (xy 123.921158 118.7995) (xy 123.921155 118.7995) (xy 123.76651 118.830261) (xy 123.766498 118.830264) + (xy 123.620827 118.890602) (xy 123.620814 118.890609) (xy 123.489711 118.97821) (xy 123.489707 118.978213) + (xy 123.378213 119.089707) (xy 123.37821 119.089711) (xy 123.290609 119.220814) (xy 123.290602 119.220827) + (xy 123.230264 119.366498) (xy 123.230261 119.36651) (xy 123.1995 119.521153) (xy 120.2505 119.521153) + (xy 120.2505 117.721153) (xy 126.9995 117.721153) (xy 126.9995 117.878846) (xy 127.030261 118.033489) + (xy 127.030264 118.033501) (xy 127.090602 118.179172) (xy 127.090609 118.179185) (xy 127.17821 118.310288) + (xy 127.178213 118.310292) (xy 127.289707 118.421786) (xy 127.289711 118.421789) (xy 127.420814 118.50939) + (xy 127.420827 118.509397) (xy 127.561394 118.567621) (xy 127.566503 118.569737) (xy 127.721153 118.600499) + (xy 127.721156 118.6005) (xy 127.721158 118.6005) (xy 127.878844 118.6005) (xy 127.878845 118.600499) + (xy 128.033497 118.569737) (xy 128.179179 118.509394) (xy 128.310289 118.421789) (xy 128.421789 118.310289) + (xy 128.509394 118.179179) (xy 128.569737 118.033497) (xy 128.6005 117.878842) (xy 128.6005 117.721158) + (xy 128.6005 117.721155) (xy 128.600499 117.721153) (xy 128.583061 117.633489) (xy 128.569737 117.566503) + (xy 128.557901 117.537927) (xy 128.509397 117.420827) (xy 128.50939 117.420814) (xy 128.421789 117.289711) + (xy 128.421786 117.289707) (xy 128.310292 117.178213) (xy 128.310288 117.17821) (xy 128.179185 117.090609) + (xy 128.179172 117.090602) (xy 128.033501 117.030264) (xy 128.033489 117.030261) (xy 127.878845 116.9995) + (xy 127.878842 116.9995) (xy 127.721158 116.9995) (xy 127.721155 116.9995) (xy 127.56651 117.030261) + (xy 127.566498 117.030264) (xy 127.420827 117.090602) (xy 127.420814 117.090609) (xy 127.289711 117.17821) + (xy 127.289707 117.178213) (xy 127.178213 117.289707) (xy 127.17821 117.289711) (xy 127.090609 117.420814) + (xy 127.090602 117.420827) (xy 127.030264 117.566498) (xy 127.030261 117.56651) (xy 126.9995 117.721153) + (xy 120.2505 117.721153) (xy 120.2505 116.521153) (xy 129.4995 116.521153) (xy 129.4995 116.678846) + (xy 129.530261 116.833489) (xy 129.530264 116.833501) (xy 129.590604 116.979176) (xy 129.626162 117.032392) + (xy 129.64704 117.099069) (xy 129.637623 117.148732) (xy 129.630262 117.166502) (xy 129.630261 117.166505) + (xy 129.5995 117.321153) (xy 129.5995 117.478846) (xy 129.630261 117.633489) (xy 129.630264 117.633501) + (xy 129.690602 117.779172) (xy 129.690609 117.779185) (xy 129.77821 117.910288) (xy 129.778213 117.910292) + (xy 129.889707 118.021786) (xy 129.889711 118.021789) (xy 130.020814 118.10939) (xy 130.020827 118.109397) + (xy 130.166498 118.169735) (xy 130.166503 118.169737) (xy 130.321153 118.200499) (xy 130.321156 118.2005) + (xy 130.321158 118.2005) (xy 130.478844 118.2005) (xy 130.492617 118.197759) (xy 130.508802 118.19454) + (xy 130.578393 118.200764) (xy 130.633572 118.243625) (xy 130.636099 118.247265) (xy 130.678209 118.310287) + (xy 130.67821 118.310288) (xy 130.678211 118.310289) (xy 130.778318 118.410396) (xy 130.811802 118.471717) + (xy 130.814636 118.498076) (xy 130.814636 118.614164) (xy 130.845397 118.768807) (xy 130.8454 118.768819) + (xy 130.905738 118.91449) (xy 130.905745 118.914503) (xy 130.993346 119.045606) (xy 130.993349 119.04561) + (xy 131.104843 119.157104) (xy 131.104847 119.157107) (xy 131.23595 119.244708) (xy 131.235963 119.244715) + (xy 131.381634 119.305053) (xy 131.381639 119.305055) (xy 131.536289 119.335817) (xy 131.536292 119.335818) + (xy 131.536294 119.335818) (xy 131.69398 119.335818) (xy 131.693981 119.335817) (xy 131.848633 119.305055) + (xy 131.994315 119.244712) (xy 132.125425 119.157107) (xy 132.236925 119.045607) (xy 132.32453 118.914497) + (xy 132.332591 118.895034) (xy 132.376431 118.840631) (xy 132.442725 118.818565) (xy 132.510425 118.835843) + (xy 132.516039 118.839381) (xy 132.620821 118.909394) (xy 132.620823 118.909395) (xy 132.620827 118.909397) + (xy 132.747998 118.962072) (xy 132.766503 118.969737) (xy 132.854426 118.987226) (xy 132.921153 119.000499) + (xy 132.921156 119.0005) (xy 132.921158 119.0005) (xy 133.078844 119.0005) (xy 133.078845 119.000499) + (xy 133.233497 118.969737) (xy 133.379179 118.909394) (xy 133.38111 118.908103) (xy 133.382276 118.907737) + (xy 133.384546 118.906525) (xy 133.384776 118.906955) (xy 133.447786 118.887226) (xy 133.515166 118.90571) + (xy 133.51885 118.908077) (xy 133.520821 118.909394) (xy 133.520824 118.909395) (xy 133.520827 118.909397) + (xy 133.647998 118.962072) (xy 133.666503 118.969737) (xy 133.754426 118.987226) (xy 133.821153 119.000499) + (xy 133.821156 119.0005) (xy 133.821158 119.0005) (xy 133.978844 119.0005) (xy 133.978845 119.000499) + (xy 134.133497 118.969737) (xy 134.279179 118.909394) (xy 134.410289 118.821789) (xy 134.521789 118.710289) + (xy 134.609394 118.579179) (xy 134.610277 118.577048) (xy 134.611035 118.576106) (xy 134.612264 118.573809) + (xy 134.612699 118.574041) (xy 134.654115 118.522646) (xy 134.720408 118.500579) (xy 134.724838 118.5005) + (xy 134.733741 118.5005) (xy 134.80078 118.520185) (xy 134.846535 118.572989) (xy 134.848302 118.577048) + (xy 134.890602 118.679172) (xy 134.890609 118.679185) (xy 134.97821 118.810288) (xy 134.978213 118.810292) + (xy 135.089707 118.921786) (xy 135.089711 118.921789) (xy 135.220814 119.00939) (xy 135.220827 119.009397) + (xy 135.366498 119.069735) (xy 135.366503 119.069737) (xy 135.521153 119.100499) (xy 135.521156 119.1005) + (xy 135.521158 119.1005) (xy 135.678844 119.1005) (xy 135.678845 119.100499) (xy 135.833497 119.069737) + (xy 135.979179 119.009394) (xy 135.98111 119.008103) (xy 135.982276 119.007737) (xy 135.984546 119.006525) + (xy 135.984776 119.006955) (xy 136.047786 118.987226) (xy 136.115166 119.00571) (xy 136.11885 119.008077) + (xy 136.120821 119.009394) (xy 136.120824 119.009395) (xy 136.120827 119.009397) (xy 136.266498 119.069735) + (xy 136.266503 119.069737) (xy 136.421153 119.100499) (xy 136.421156 119.1005) (xy 136.421158 119.1005) + (xy 136.578844 119.1005) (xy 136.578845 119.100499) (xy 136.733497 119.069737) (xy 136.879179 119.009394) + (xy 137.010289 118.921789) (xy 137.121789 118.810289) (xy 137.209394 118.679179) (xy 137.233429 118.621153) + (xy 139.7995 118.621153) (xy 139.7995 118.778846) (xy 139.830261 118.933489) (xy 139.830264 118.933501) + (xy 139.890602 119.079172) (xy 139.890609 119.079185) (xy 139.97821 119.210288) (xy 139.978213 119.210292) + (xy 140.089707 119.321786) (xy 140.089711 119.321789) (xy 140.220814 119.40939) (xy 140.220827 119.409397) + (xy 140.366498 119.469735) (xy 140.366503 119.469737) (xy 140.521153 119.500499) (xy 140.521156 119.5005) + (xy 140.521158 119.5005) (xy 140.678844 119.5005) (xy 140.678845 119.500499) (xy 140.833497 119.469737) + (xy 140.979179 119.409394) (xy 141.110289 119.321789) (xy 141.221789 119.210289) (xy 141.309394 119.079179) + (xy 141.369737 118.933497) (xy 141.4005 118.778842) (xy 141.4005 118.621158) (xy 141.4005 118.621155) + (xy 141.400499 118.621153) (xy 141.39215 118.579179) (xy 141.369737 118.466503) (xy 141.333427 118.378842) + (xy 141.309397 118.320827) (xy 141.30939 118.320814) (xy 141.221789 118.189711) (xy 141.221786 118.189707) + (xy 141.110292 118.078213) (xy 141.110288 118.07821) (xy 140.979185 117.990609) (xy 140.979172 117.990602) + (xy 140.833501 117.930264) (xy 140.833489 117.930261) (xy 140.678845 117.8995) (xy 140.678842 117.8995) + (xy 140.521158 117.8995) (xy 140.521155 117.8995) (xy 140.36651 117.930261) (xy 140.366498 117.930264) + (xy 140.220827 117.990602) (xy 140.220814 117.990609) (xy 140.089711 118.07821) (xy 140.089707 118.078213) + (xy 139.978213 118.189707) (xy 139.97821 118.189711) (xy 139.890609 118.320814) (xy 139.890602 118.320827) + (xy 139.830264 118.466498) (xy 139.830261 118.46651) (xy 139.7995 118.621153) (xy 137.233429 118.621153) + (xy 137.250815 118.57918) (xy 137.255603 118.567621) (xy 137.255605 118.567614) (xy 137.269737 118.533497) + (xy 137.3005 118.378842) (xy 137.3005 118.221158) (xy 137.3005 118.221155) (xy 137.300499 118.221153) + (xy 137.278269 118.109397) (xy 137.269737 118.066503) (xy 137.251215 118.021786) (xy 137.209397 117.920827) + (xy 137.20939 117.920814) (xy 137.121789 117.789711) (xy 137.121786 117.789707) (xy 137.010292 117.678213) + (xy 137.010288 117.67821) (xy 136.879185 117.590609) (xy 136.879172 117.590602) (xy 136.733501 117.530264) + (xy 136.733489 117.530261) (xy 136.578845 117.4995) (xy 136.578842 117.4995) (xy 136.421158 117.4995) + (xy 136.421155 117.4995) (xy 136.26651 117.530261) (xy 136.266498 117.530264) (xy 136.120822 117.590604) + (xy 136.12082 117.590605) (xy 136.118885 117.591899) (xy 136.117717 117.592264) (xy 136.115451 117.593476) + (xy 136.115221 117.593045) (xy 136.052206 117.612773) (xy 135.984827 117.594285) (xy 135.981115 117.591899) + (xy 135.979179 117.590605) (xy 135.979177 117.590604) (xy 135.833501 117.530264) (xy 135.833489 117.530261) + (xy 135.678845 117.4995) (xy 135.678842 117.4995) (xy 135.566259 117.4995) (xy 135.49922 117.479815) + (xy 135.453465 117.427011) (xy 135.451698 117.422952) (xy 135.409397 117.320827) (xy 135.40939 117.320814) + (xy 135.321789 117.189711) (xy 135.321786 117.189707) (xy 135.210292 117.078213) (xy 135.210288 117.07821) + (xy 135.079185 116.990609) (xy 135.079172 116.990602) (xy 134.933501 116.930264) (xy 134.933489 116.930261) + (xy 134.778845 116.8995) (xy 134.778842 116.8995) (xy 134.621158 116.8995) (xy 134.621155 116.8995) + (xy 134.46651 116.930261) (xy 134.466498 116.930264) (xy 134.320827 116.990602) (xy 134.320814 116.990609) + (xy 134.189711 117.07821) (xy 134.189707 117.078213) (xy 134.078213 117.189707) (xy 134.07821 117.189711) + (xy 133.990609 117.320814) (xy 133.990607 117.320819) (xy 133.990606 117.320821) (xy 133.990467 117.321158) + (xy 133.989725 117.322949) (xy 133.988964 117.323893) (xy 133.987736 117.326191) (xy 133.9873 117.325958) + (xy 133.945885 117.377354) (xy 133.879592 117.399421) (xy 133.875162 117.3995) (xy 133.821155 117.3995) + (xy 133.66651 117.430261) (xy 133.666498 117.430264) (xy 133.520822 117.490604) (xy 133.52082 117.490605) + (xy 133.518885 117.491899) (xy 133.517717 117.492264) (xy 133.515451 117.493476) (xy 133.515221 117.493045) + (xy 133.452206 117.512773) (xy 133.384827 117.494285) (xy 133.381115 117.491899) (xy 133.379179 117.490605) + (xy 133.379177 117.490604) (xy 133.233501 117.430264) (xy 133.233489 117.430261) (xy 133.078845 117.3995) + (xy 133.078842 117.3995) (xy 132.921158 117.3995) (xy 132.921155 117.3995) (xy 132.76651 117.430261) + (xy 132.766498 117.430264) (xy 132.620827 117.490602) (xy 132.620814 117.490609) (xy 132.489711 117.57821) + (xy 132.489707 117.578213) (xy 132.378213 117.689707) (xy 132.378208 117.689713) (xy 132.325702 117.768293) + (xy 132.27209 117.813097) (xy 132.202764 117.821804) (xy 132.139737 117.791649) (xy 132.103019 117.732205) + (xy 132.100984 117.723592) (xy 132.096391 117.7005) (xy 132.069737 117.566503) (xy 132.057901 117.537927) + (xy 132.009397 117.420827) (xy 132.00939 117.420814) (xy 131.921789 117.289711) (xy 131.921786 117.289707) + (xy 131.810292 117.178213) (xy 131.810288 117.17821) (xy 131.679185 117.090609) (xy 131.679172 117.090602) + (xy 131.533501 117.030264) (xy 131.533489 117.030261) (xy 131.378845 116.9995) (xy 131.378842 116.9995) + (xy 131.221158 116.9995) (xy 131.221157 116.9995) (xy 131.208733 117.001971) (xy 131.139141 116.995742) + (xy 131.083965 116.952878) (xy 131.060722 116.886987) (xy 131.068842 116.839588) (xy 131.067969 116.839324) + (xy 131.069731 116.833509) (xy 131.069737 116.833497) (xy 131.072192 116.821153) (xy 138.5995 116.821153) + (xy 138.5995 116.978846) (xy 138.630261 117.133489) (xy 138.630264 117.133501) (xy 138.690602 117.279172) + (xy 138.690609 117.279185) (xy 138.77821 117.410288) (xy 138.778213 117.410292) (xy 138.889707 117.521786) + (xy 138.889711 117.521789) (xy 139.020814 117.60939) (xy 139.020827 117.609397) (xy 139.089706 117.637927) + (xy 139.166503 117.669737) (xy 139.321153 117.700499) (xy 139.321156 117.7005) (xy 139.321158 117.7005) + (xy 139.478844 117.7005) (xy 139.478845 117.700499) (xy 139.633497 117.669737) (xy 139.779179 117.609394) + (xy 139.910289 117.521789) (xy 140.021789 117.410289) (xy 140.109394 117.279179) (xy 140.169737 117.133497) + (xy 140.2005 116.978842) (xy 140.2005 116.821158) (xy 140.2005 116.821155) (xy 140.200499 116.821153) + (xy 140.172192 116.678846) (xy 140.169737 116.666503) (xy 140.109534 116.521158) (xy 140.109397 116.520827) + (xy 140.10939 116.520814) (xy 140.021789 116.389711) (xy 140.021786 116.389707) (xy 139.910292 116.278213) + (xy 139.910288 116.27821) (xy 139.779185 116.190609) (xy 139.779172 116.190602) (xy 139.633501 116.130264) + (xy 139.633489 116.130261) (xy 139.478845 116.0995) (xy 139.478842 116.0995) (xy 139.321158 116.0995) + (xy 139.321155 116.0995) (xy 139.16651 116.130261) (xy 139.166498 116.130264) (xy 139.020827 116.190602) + (xy 139.020814 116.190609) (xy 138.889711 116.27821) (xy 138.889707 116.278213) (xy 138.778213 116.389707) + (xy 138.77821 116.389711) (xy 138.690609 116.520814) (xy 138.690602 116.520827) (xy 138.630264 116.666498) + (xy 138.630261 116.66651) (xy 138.5995 116.821153) (xy 131.072192 116.821153) (xy 131.1005 116.678842) + (xy 131.1005 116.521158) (xy 131.1005 116.521155) (xy 131.100499 116.521153) (xy 131.074353 116.389711) + (xy 131.069737 116.366503) (xy 131.069735 116.366498) (xy 131.009397 116.220827) (xy 131.00939 116.220814) + (xy 130.921789 116.089711) (xy 130.921786 116.089707) (xy 130.810292 115.978213) (xy 130.810288 115.97821) + (xy 130.679185 115.890609) (xy 130.679172 115.890602) (xy 130.533501 115.830264) (xy 130.533489 115.830261) + (xy 130.378845 115.7995) (xy 130.378842 115.7995) (xy 130.221158 115.7995) (xy 130.221155 115.7995) + (xy 130.06651 115.830261) (xy 130.066498 115.830264) (xy 129.920827 115.890602) (xy 129.920814 115.890609) + (xy 129.789711 115.97821) (xy 129.789707 115.978213) (xy 129.678213 116.089707) (xy 129.67821 116.089711) + (xy 129.590609 116.220814) (xy 129.590602 116.220827) (xy 129.530264 116.366498) (xy 129.530261 116.36651) + (xy 129.4995 116.521153) (xy 120.2505 116.521153) (xy 120.2505 114.021153) (xy 121.8995 114.021153) + (xy 121.8995 114.178846) (xy 121.930261 114.333489) (xy 121.930264 114.333501) (xy 121.990602 114.479172) + (xy 121.990609 114.479185) (xy 122.07821 114.610288) (xy 122.078213 114.610292) (xy 122.189707 114.721786) + (xy 122.189711 114.721789) (xy 122.320814 114.80939) (xy 122.320827 114.809397) (xy 122.458683 114.866498) + (xy 122.466503 114.869737) (xy 122.621153 114.900499) (xy 122.621156 114.9005) (xy 122.621158 114.9005) + (xy 122.778844 114.9005) (xy 122.778845 114.900499) (xy 122.933497 114.869737) (xy 123.079179 114.809394) + (xy 123.210289 114.721789) (xy 123.321789 114.610289) (xy 123.409394 114.479179) (xy 123.469737 114.333497) + (xy 123.5005 114.178842) (xy 123.5005 114.121153) (xy 129.6995 114.121153) (xy 129.6995 114.278846) + (xy 129.730261 114.433489) (xy 129.730264 114.433501) (xy 129.790602 114.579172) (xy 129.790609 114.579185) + (xy 129.87821 114.710288) (xy 129.878213 114.710292) (xy 129.989707 114.821786) (xy 129.989711 114.821789) + (xy 130.120814 114.90939) (xy 130.120827 114.909397) (xy 130.266498 114.969735) (xy 130.266503 114.969737) + (xy 130.396982 114.995691) (xy 130.421153 115.000499) (xy 130.421156 115.0005) (xy 130.421158 115.0005) + (xy 130.578844 115.0005) (xy 130.578845 115.000499) (xy 130.733497 114.969737) (xy 130.733509 114.969731) + (xy 130.739324 114.967969) (xy 130.740158 114.97072) (xy 130.797359 114.964497) (xy 130.859878 114.995691) + (xy 130.895608 115.055734) (xy 130.8995 115.086555) (xy 130.8995 115.178846) (xy 130.930261 115.333489) + (xy 130.930264 115.333501) (xy 130.990602 115.479172) (xy 130.990609 115.479185) (xy 131.07821 115.610288) + (xy 131.078213 115.610292) (xy 131.189707 115.721786) (xy 131.189711 115.721789) (xy 131.320814 115.80939) + (xy 131.320827 115.809397) (xy 131.466498 115.869735) (xy 131.466503 115.869737) (xy 131.621153 115.900499) + (xy 131.621156 115.9005) (xy 131.621158 115.9005) (xy 131.778844 115.9005) (xy 131.778845 115.900499) + (xy 131.933497 115.869737) (xy 132.079179 115.809394) (xy 132.210289 115.721789) (xy 132.321789 115.610289) + (xy 132.409394 115.479179) (xy 132.469737 115.333497) (xy 132.5005 115.178842) (xy 132.5005 115.021158) + (xy 132.5005 115.021155) (xy 132.500499 115.021153) (xy 132.478269 114.909397) (xy 132.469737 114.866503) + (xy 132.409794 114.721786) (xy 132.409397 114.720827) (xy 132.40939 114.720814) (xy 132.321789 114.589711) + (xy 132.321786 114.589707) (xy 132.210292 114.478213) (xy 132.210288 114.47821) (xy 132.079185 114.390609) + (xy 132.079172 114.390602) (xy 131.933501 114.330264) (xy 131.933489 114.330261) (xy 131.778845 114.2995) + (xy 131.778842 114.2995) (xy 131.621158 114.2995) (xy 131.621155 114.2995) (xy 131.46651 114.330261) + (xy 131.460676 114.332031) (xy 131.459873 114.329385) (xy 131.444688 114.330963) (xy 131.418434 114.337296) + (xy 131.410455 114.334522) (xy 131.402056 114.335396) (xy 131.37795 114.323223) (xy 131.352437 114.314355) + (xy 131.347224 114.307708) (xy 131.339687 114.303902) (xy 131.325988 114.280629) (xy 131.309321 114.259376) + (xy 131.307307 114.248892) (xy 131.304245 114.243689) (xy 131.301046 114.225065) (xy 131.3005 114.219264) + (xy 131.3005 114.121158) (xy 131.280608 114.021153) (xy 138.7995 114.021153) (xy 138.7995 114.178846) + (xy 138.830261 114.333489) (xy 138.830264 114.333501) (xy 138.890602 114.479172) (xy 138.890609 114.479185) + (xy 138.97821 114.610288) (xy 138.978213 114.610292) (xy 139.089707 114.721786) (xy 139.089711 114.721789) + (xy 139.220814 114.80939) (xy 139.220827 114.809397) (xy 139.358683 114.866498) (xy 139.366503 114.869737) + (xy 139.521153 114.900499) (xy 139.521156 114.9005) (xy 139.521158 114.9005) (xy 139.678844 114.9005) + (xy 139.678845 114.900499) (xy 139.833497 114.869737) (xy 139.979179 114.809394) (xy 140.110289 114.721789) + (xy 140.221789 114.610289) (xy 140.309394 114.479179) (xy 140.369737 114.333497) (xy 140.4005 114.178842) + (xy 140.4005 114.121153) (xy 141.1995 114.121153) (xy 141.1995 114.278846) (xy 141.230261 114.433489) + (xy 141.230264 114.433501) (xy 141.290602 114.579172) (xy 141.290609 114.579185) (xy 141.37821 114.710288) + (xy 141.378213 114.710292) (xy 141.489707 114.821786) (xy 141.489711 114.821789) (xy 141.620814 114.90939) + (xy 141.620827 114.909397) (xy 141.766498 114.969735) (xy 141.766503 114.969737) (xy 141.896982 114.995691) + (xy 141.921153 115.000499) (xy 141.921156 115.0005) (xy 141.921158 115.0005) (xy 142.078844 115.0005) + (xy 142.078845 115.000499) (xy 142.233497 114.969737) (xy 142.379179 114.909394) (xy 142.510289 114.821789) + (xy 142.621789 114.710289) (xy 142.709394 114.579179) (xy 142.769737 114.433497) (xy 142.8005 114.278842) + (xy 142.8005 114.121158) (xy 142.8005 114.121155) (xy 142.800499 114.121153) (xy 142.769737 113.966503) + (xy 142.728314 113.866498) (xy 142.709397 113.820827) (xy 142.70939 113.820814) (xy 142.621789 113.689711) + (xy 142.621786 113.689707) (xy 142.510292 113.578213) (xy 142.510288 113.57821) (xy 142.379185 113.490609) + (xy 142.379172 113.490602) (xy 142.233501 113.430264) (xy 142.233489 113.430261) (xy 142.078845 113.3995) + (xy 142.078842 113.3995) (xy 141.921158 113.3995) (xy 141.921155 113.3995) (xy 141.76651 113.430261) + (xy 141.766498 113.430264) (xy 141.620827 113.490602) (xy 141.620814 113.490609) (xy 141.489711 113.57821) + (xy 141.489707 113.578213) (xy 141.378213 113.689707) (xy 141.37821 113.689711) (xy 141.290609 113.820814) + (xy 141.290602 113.820827) (xy 141.230264 113.966498) (xy 141.230261 113.96651) (xy 141.1995 114.121153) + (xy 140.4005 114.121153) (xy 140.4005 114.021158) (xy 140.4005 114.021155) (xy 140.400499 114.021153) + (xy 140.369738 113.86651) (xy 140.369737 113.866503) (xy 140.350812 113.820814) (xy 140.309397 113.720827) + (xy 140.30939 113.720814) (xy 140.221789 113.589711) (xy 140.221786 113.589707) (xy 140.110292 113.478213) + (xy 140.110288 113.47821) (xy 139.979185 113.390609) (xy 139.979172 113.390602) (xy 139.833501 113.330264) + (xy 139.833489 113.330261) (xy 139.678845 113.2995) (xy 139.678842 113.2995) (xy 139.521158 113.2995) + (xy 139.521155 113.2995) (xy 139.36651 113.330261) (xy 139.366498 113.330264) (xy 139.220827 113.390602) + (xy 139.220814 113.390609) (xy 139.089711 113.47821) (xy 139.089707 113.478213) (xy 138.978213 113.589707) + (xy 138.97821 113.589711) (xy 138.890609 113.720814) (xy 138.890602 113.720827) (xy 138.830264 113.866498) + (xy 138.830261 113.86651) (xy 138.7995 114.021153) (xy 131.280608 114.021153) (xy 131.269737 113.966503) + (xy 131.228314 113.866498) (xy 131.209397 113.820827) (xy 131.20939 113.820814) (xy 131.121789 113.689711) + (xy 131.121786 113.689707) (xy 131.010292 113.578213) (xy 131.010288 113.57821) (xy 130.879185 113.490609) + (xy 130.879172 113.490602) (xy 130.733501 113.430264) (xy 130.733489 113.430261) (xy 130.578845 113.3995) + (xy 130.578842 113.3995) (xy 130.421158 113.3995) (xy 130.421155 113.3995) (xy 130.26651 113.430261) + (xy 130.266498 113.430264) (xy 130.120827 113.490602) (xy 130.120814 113.490609) (xy 129.989711 113.57821) + (xy 129.989707 113.578213) (xy 129.878213 113.689707) (xy 129.87821 113.689711) (xy 129.790609 113.820814) + (xy 129.790602 113.820827) (xy 129.730264 113.966498) (xy 129.730261 113.96651) (xy 129.6995 114.121153) + (xy 123.5005 114.121153) (xy 123.5005 114.021158) (xy 123.5005 114.021155) (xy 123.500499 114.021153) + (xy 123.469738 113.86651) (xy 123.469737 113.866503) (xy 123.450812 113.820814) (xy 123.409397 113.720827) + (xy 123.40939 113.720814) (xy 123.321789 113.589711) (xy 123.321786 113.589707) (xy 123.210292 113.478213) + (xy 123.210288 113.47821) (xy 123.079185 113.390609) (xy 123.079172 113.390602) (xy 122.933501 113.330264) + (xy 122.933489 113.330261) (xy 122.778845 113.2995) (xy 122.778842 113.2995) (xy 122.621158 113.2995) + (xy 122.621155 113.2995) (xy 122.46651 113.330261) (xy 122.466498 113.330264) (xy 122.320827 113.390602) + (xy 122.320814 113.390609) (xy 122.189711 113.47821) (xy 122.189707 113.478213) (xy 122.078213 113.589707) + (xy 122.07821 113.589711) (xy 121.990609 113.720814) (xy 121.990602 113.720827) (xy 121.930264 113.866498) + (xy 121.930261 113.86651) (xy 121.8995 114.021153) (xy 120.2505 114.021153) (xy 120.2505 111.521153) + (xy 123.3995 111.521153) (xy 123.3995 111.678846) (xy 123.430261 111.833489) (xy 123.430264 111.833501) + (xy 123.490602 111.979172) (xy 123.490609 111.979185) (xy 123.57821 112.110288) (xy 123.578213 112.110292) + (xy 123.689707 112.221786) (xy 123.689711 112.221789) (xy 123.820814 112.30939) (xy 123.820827 112.309397) + (xy 123.966498 112.369735) (xy 123.966503 112.369737) (xy 124.121153 112.400499) (xy 124.121156 112.4005) + (xy 124.121158 112.4005) (xy 124.278844 112.4005) (xy 124.278845 112.400499) (xy 124.433497 112.369737) + (xy 124.579179 112.309394) (xy 124.710289 112.221789) (xy 124.821789 112.110289) (xy 124.909394 111.979179) + (xy 124.969737 111.833497) (xy 125.0005 111.678842) (xy 125.0005 111.521158) (xy 125.0005 111.521155) + (xy 125.000499 111.521153) (xy 124.980734 111.421789) (xy 124.969737 111.366503) (xy 124.946452 111.310288) + (xy 124.909397 111.220827) (xy 124.90939 111.220814) (xy 124.821789 111.089711) (xy 124.821786 111.089707) + (xy 124.710292 110.978213) (xy 124.710288 110.97821) (xy 124.579185 110.890609) (xy 124.579172 110.890602) + (xy 124.458154 110.840475) (xy 124.458147 110.840473) (xy 124.433497 110.830263) (xy 124.278842 110.7995) + (xy 124.121158 110.7995) (xy 124.121155 110.7995) (xy 123.96651 110.830261) (xy 123.966498 110.830264) + (xy 123.820827 110.890602) (xy 123.820814 110.890609) (xy 123.689711 110.97821) (xy 123.689707 110.978213) + (xy 123.578213 111.089707) (xy 123.57821 111.089711) (xy 123.490609 111.220814) (xy 123.490602 111.220827) + (xy 123.430264 111.366498) (xy 123.430261 111.36651) (xy 123.3995 111.521153) (xy 120.2505 111.521153) + (xy 120.2505 109.721153) (xy 123.7995 109.721153) (xy 123.7995 109.878846) (xy 123.830261 110.033489) + (xy 123.830264 110.033501) (xy 123.890602 110.179172) (xy 123.890609 110.179185) (xy 123.97821 110.310288) + (xy 123.978213 110.310292) (xy 124.089707 110.421786) (xy 124.089711 110.421789) (xy 124.220814 110.50939) + (xy 124.220827 110.509397) (xy 124.341844 110.559523) (xy 124.366503 110.569737) (xy 124.521158 110.6005) + (xy 124.521249 110.6005) (xy 124.678844 110.6005) (xy 124.678845 110.600499) (xy 124.833497 110.569737) + (xy 124.979179 110.509394) (xy 125.110289 110.421789) (xy 125.170144 110.361933) (xy 125.231463 110.32845) + (xy 125.301155 110.333434) (xy 125.326714 110.346514) (xy 125.420814 110.40939) (xy 125.420827 110.409397) + (xy 125.566498 110.469735) (xy 125.566503 110.469737) (xy 125.721153 110.500499) (xy 125.721156 110.5005) + (xy 125.721158 110.5005) (xy 125.878844 110.5005) (xy 125.878845 110.500499) (xy 126.033497 110.469737) + (xy 126.151592 110.420821) (xy 126.179172 110.409397) (xy 126.179172 110.409396) (xy 126.179179 110.409394) + (xy 126.310289 110.321789) (xy 126.421789 110.210289) (xy 126.509394 110.079179) (xy 126.569737 109.933497) + (xy 126.592083 109.821158) (xy 126.592084 109.821153) (xy 129.5995 109.821153) (xy 129.5995 109.978846) + (xy 129.630261 110.133489) (xy 129.630264 110.133501) (xy 129.690602 110.279172) (xy 129.690612 110.27919) + (xy 129.751732 110.370663) (xy 129.77261 110.43734) (xy 129.763192 110.487004) (xy 129.730262 110.566506) + (xy 129.73026 110.566511) (xy 129.6995 110.721153) (xy 129.6995 110.878846) (xy 129.730261 111.033489) + (xy 129.730264 111.033501) (xy 129.790602 111.179172) (xy 129.790609 111.179185) (xy 129.87821 111.310288) + (xy 129.878213 111.310292) (xy 129.989707 111.421786) (xy 129.989711 111.421789) (xy 130.120814 111.50939) + (xy 130.120827 111.509397) (xy 130.266498 111.569735) (xy 130.266503 111.569737) (xy 130.421153 111.600499) + (xy 130.421156 111.6005) (xy 130.421158 111.6005) (xy 130.578844 111.6005) (xy 130.578845 111.600499) + (xy 130.733497 111.569737) (xy 130.879179 111.509394) (xy 131.010289 111.421789) (xy 131.121789 111.310289) + (xy 131.209394 111.179179) (xy 131.269737 111.033497) (xy 131.3005 110.878842) (xy 131.3005 110.721158) + (xy 131.3005 110.721155) (xy 131.300499 110.721153) (xy 131.27038 110.569735) (xy 131.269737 110.566503) + (xy 131.242398 110.5005) (xy 131.209397 110.420827) (xy 131.20939 110.420814) (xy 131.148267 110.329337) + (xy 131.127389 110.262659) (xy 131.136808 110.212993) (xy 131.137928 110.210289) (xy 131.169737 110.133497) + (xy 131.2005 109.978842) (xy 131.2005 109.821158) (xy 131.2005 109.821155) (xy 131.176982 109.702925) + (xy 131.183209 109.633333) (xy 131.226072 109.578156) (xy 131.229675 109.575653) (xy 131.310289 109.521789) + (xy 131.421789 109.410289) (xy 131.509394 109.279179) (xy 131.533429 109.221153) (xy 146.4995 109.221153) + (xy 146.4995 109.378846) (xy 146.530261 109.533489) (xy 146.530264 109.533501) (xy 146.590602 109.679172) + (xy 146.590609 109.679185) (xy 146.67821 109.810288) (xy 146.678213 109.810292) (xy 146.789707 109.921786) + (xy 146.789711 109.921789) (xy 146.920814 110.00939) (xy 146.920827 110.009397) (xy 147.066498 110.069735) + (xy 147.066503 110.069737) (xy 147.221153 110.100499) (xy 147.221156 110.1005) (xy 147.221158 110.1005) + (xy 147.378844 110.1005) (xy 147.378845 110.100499) (xy 147.533497 110.069737) (xy 147.679179 110.009394) + (xy 147.810289 109.921789) (xy 147.921789 109.810289) (xy 148.009394 109.679179) (xy 148.069737 109.533497) + (xy 148.1005 109.378842) (xy 148.1005 109.221158) (xy 148.1005 109.221155) (xy 148.100499 109.221153) + (xy 148.074531 109.090606) (xy 148.069737 109.066503) (xy 148.069735 109.066498) (xy 148.009397 108.920827) + (xy 148.00939 108.920814) (xy 147.921789 108.789711) (xy 147.921786 108.789707) (xy 147.810292 108.678213) + (xy 147.810288 108.67821) (xy 147.679185 108.590609) (xy 147.679172 108.590602) (xy 147.533501 108.530264) + (xy 147.533489 108.530261) (xy 147.378845 108.4995) (xy 147.378842 108.4995) (xy 147.221158 108.4995) + (xy 147.221155 108.4995) (xy 147.06651 108.530261) (xy 147.066498 108.530264) (xy 146.920827 108.590602) + (xy 146.920814 108.590609) (xy 146.789711 108.67821) (xy 146.789707 108.678213) (xy 146.678213 108.789707) + (xy 146.67821 108.789711) (xy 146.590609 108.920814) (xy 146.590602 108.920827) (xy 146.530264 109.066498) + (xy 146.530261 109.06651) (xy 146.4995 109.221153) (xy 131.533429 109.221153) (xy 131.569737 109.133497) + (xy 131.6005 108.978842) (xy 131.6005 108.821158) (xy 131.6005 108.821155) (xy 131.600499 108.821153) + (xy 131.594244 108.789707) (xy 131.569737 108.666503) (xy 131.527049 108.563446) (xy 131.519581 108.493978) + (xy 131.532264 108.457521) (xy 131.533649 108.454928) (xy 131.533659 108.454914) (xy 131.594002 108.309232) + (xy 131.611522 108.221153) (xy 144.0995 108.221153) (xy 144.0995 108.378846) (xy 144.130261 108.533489) + (xy 144.130264 108.533501) (xy 144.190602 108.679172) (xy 144.190609 108.679185) (xy 144.27821 108.810288) + (xy 144.278213 108.810292) (xy 144.389707 108.921786) (xy 144.389711 108.921789) (xy 144.520814 109.00939) + (xy 144.520827 109.009397) (xy 144.658683 109.066498) (xy 144.666503 109.069737) (xy 144.821153 109.100499) + (xy 144.821156 109.1005) (xy 144.821158 109.1005) (xy 144.978844 109.1005) (xy 144.978845 109.100499) + (xy 144.996061 109.097075) (xy 145.014287 109.09345) (xy 145.014292 109.093449) (xy 145.0998 109.076439) + (xy 145.133497 109.069737) (xy 145.279179 109.009394) (xy 145.410289 108.921789) (xy 145.521789 108.810289) + (xy 145.609394 108.679179) (xy 145.669737 108.533497) (xy 145.7005 108.378842) (xy 145.7005 108.221158) + (xy 145.7005 108.221155) (xy 145.700499 108.221153) (xy 145.687257 108.154581) (xy 145.669737 108.066503) + (xy 145.609794 107.921786) (xy 145.609397 107.920827) (xy 145.60939 107.920814) (xy 145.521789 107.789711) + (xy 145.521786 107.789707) (xy 145.410292 107.678213) (xy 145.410288 107.67821) (xy 145.279185 107.590609) + (xy 145.279172 107.590602) (xy 145.133501 107.530264) (xy 145.133489 107.530261) (xy 144.978845 107.4995) + (xy 144.978842 107.4995) (xy 144.821158 107.4995) (xy 144.821155 107.4995) (xy 144.66651 107.530261) + (xy 144.666498 107.530264) (xy 144.520827 107.590602) (xy 144.520814 107.590609) (xy 144.389711 107.67821) + (xy 144.389707 107.678213) (xy 144.278213 107.789707) (xy 144.27821 107.789711) (xy 144.190609 107.920814) + (xy 144.190602 107.920827) (xy 144.130264 108.066498) (xy 144.130261 108.06651) (xy 144.0995 108.221153) + (xy 131.611522 108.221153) (xy 131.624765 108.154577) (xy 131.624765 107.996893) (xy 131.624765 107.99689) + (xy 131.624764 107.996888) (xy 131.594003 107.842245) (xy 131.594002 107.842238) (xy 131.58077 107.810292) + (xy 131.533662 107.696562) (xy 131.533655 107.696549) (xy 131.446054 107.565446) (xy 131.446051 107.565442) + (xy 131.344025 107.463416) (xy 131.31054 107.402093) (xy 131.315524 107.332401) (xy 131.344025 107.288054) + (xy 131.421786 107.210292) (xy 131.421789 107.210289) (xy 131.509394 107.079179) (xy 131.569737 106.933497) + (xy 131.572192 106.921153) (xy 132.2995 106.921153) (xy 132.2995 107.078846) (xy 132.330261 107.233489) + (xy 132.330264 107.233501) (xy 132.390602 107.379172) (xy 132.390609 107.379185) (xy 132.47821 107.510288) + (xy 132.478213 107.510292) (xy 132.589707 107.621786) (xy 132.589711 107.621789) (xy 132.720814 107.70939) + (xy 132.720827 107.709397) (xy 132.866498 107.769735) (xy 132.866503 107.769737) (xy 133.021153 107.800499) + (xy 133.021156 107.8005) (xy 133.021158 107.8005) (xy 133.178844 107.8005) (xy 133.178845 107.800499) + (xy 133.333497 107.769737) (xy 133.479179 107.709394) (xy 133.610289 107.621789) (xy 133.721789 107.510289) + (xy 133.809394 107.379179) (xy 133.811688 107.373642) (xy 133.82877 107.332401) (xy 133.869737 107.233497) + (xy 133.9005 107.078842) (xy 133.9005 106.921158) (xy 133.9005 106.921155) (xy 133.900499 106.921153) + (xy 133.882347 106.829897) (xy 133.869737 106.766503) (xy 133.83565 106.684208) (xy 133.809397 106.620827) + (xy 133.80939 106.620814) (xy 133.721789 106.489711) (xy 133.721786 106.489707) (xy 133.610292 106.378213) + (xy 133.610288 106.37821) (xy 133.479185 106.290609) (xy 133.479172 106.290602) (xy 133.333501 106.230264) + (xy 133.333489 106.230261) (xy 133.178845 106.1995) (xy 133.178842 106.1995) (xy 133.021158 106.1995) + (xy 133.021155 106.1995) (xy 132.86651 106.230261) (xy 132.866498 106.230264) (xy 132.720827 106.290602) + (xy 132.720814 106.290609) (xy 132.589711 106.37821) (xy 132.589707 106.378213) (xy 132.478213 106.489707) + (xy 132.47821 106.489711) (xy 132.390609 106.620814) (xy 132.390602 106.620827) (xy 132.330264 106.766498) + (xy 132.330261 106.76651) (xy 132.2995 106.921153) (xy 131.572192 106.921153) (xy 131.572257 106.920827) + (xy 131.578216 106.890874) (xy 131.578216 106.890873) (xy 131.600499 106.778846) (xy 131.6005 106.778844) + (xy 131.6005 106.621155) (xy 131.600499 106.621153) (xy 131.574353 106.489711) (xy 131.569737 106.466503) + (xy 131.551233 106.421829) (xy 131.509397 106.320827) (xy 131.50939 106.320814) (xy 131.421789 106.189711) + (xy 131.421786 106.189707) (xy 131.353232 106.121153) (xy 138.0995 106.121153) (xy 138.0995 106.278846) + (xy 138.130261 106.433489) (xy 138.130264 106.433501) (xy 138.190602 106.579172) (xy 138.190609 106.579185) + (xy 138.27821 106.710288) (xy 138.278213 106.710292) (xy 138.389707 106.821786) (xy 138.389711 106.821789) + (xy 138.520814 106.90939) (xy 138.520827 106.909397) (xy 138.656158 106.965452) (xy 138.666503 106.969737) + (xy 138.821153 107.000499) (xy 138.821156 107.0005) (xy 138.821158 107.0005) (xy 138.978844 107.0005) + (xy 138.978845 107.000499) (xy 139.133497 106.969737) (xy 139.201315 106.941645) (xy 139.270782 106.934177) + (xy 139.333261 106.965452) (xy 139.336447 106.968526) (xy 139.389707 107.021786) (xy 139.389711 107.021789) + (xy 139.520814 107.10939) (xy 139.520827 107.109397) (xy 139.666498 107.169735) (xy 139.666503 107.169737) + (xy 139.821153 107.200499) (xy 139.821156 107.2005) (xy 139.821158 107.2005) (xy 139.978844 107.2005) + (xy 139.978845 107.200499) (xy 140.133497 107.169737) (xy 140.279179 107.109394) (xy 140.410289 107.021789) + (xy 140.428606 107.003472) (xy 140.489928 106.969985) (xy 140.55962 106.974968) (xy 140.615554 107.016838) + (xy 140.619391 107.02226) (xy 140.67821 107.110288) (xy 140.678213 107.110292) (xy 140.789707 107.221786) + (xy 140.789711 107.221789) (xy 140.920814 107.30939) (xy 140.920827 107.309397) (xy 140.950745 107.321789) + (xy 141.066503 107.369737) (xy 141.121831 107.380742) (xy 141.18374 107.413126) (xy 141.218315 107.473841) + (xy 141.219256 107.478166) (xy 141.230261 107.533492) (xy 141.230264 107.533501) (xy 141.290602 107.679172) + (xy 141.290609 107.679185) (xy 141.37821 107.810288) (xy 141.378213 107.810292) (xy 141.489707 107.921786) + (xy 141.489711 107.921789) (xy 141.620814 108.00939) (xy 141.620827 108.009397) (xy 141.758683 108.066498) + (xy 141.766503 108.069737) (xy 141.921153 108.100499) (xy 141.921156 108.1005) (xy 141.921158 108.1005) + (xy 142.078844 108.1005) (xy 142.078845 108.100499) (xy 142.089179 108.098443) (xy 142.114287 108.09345) + (xy 142.114292 108.093449) (xy 142.1998 108.076439) (xy 142.233497 108.069737) (xy 142.379179 108.009394) + (xy 142.510289 107.921789) (xy 142.621789 107.810289) (xy 142.709394 107.679179) (xy 142.769737 107.533497) + (xy 142.8005 107.378842) (xy 142.8005 107.221158) (xy 142.8005 107.221155) (xy 142.800499 107.221153) + (xy 142.778447 107.110292) (xy 142.769737 107.066503) (xy 142.742398 107.0005) (xy 142.709397 106.920827) + (xy 142.70939 106.920814) (xy 142.621789 106.789711) (xy 142.621786 106.789707) (xy 142.510292 106.678213) + (xy 142.510288 106.67821) (xy 142.379185 106.590609) (xy 142.379172 106.590602) (xy 142.233501 106.530264) + (xy 142.233492 106.530261) (xy 142.178166 106.519256) (xy 142.116256 106.48687) (xy 142.081682 106.426154) + (xy 142.08075 106.421874) (xy 142.069737 106.366503) (xy 142.047854 106.313673) (xy 142.009397 106.220827) + (xy 142.00939 106.220814) (xy 141.921789 106.089711) (xy 141.921786 106.089707) (xy 141.810292 105.978213) + (xy 141.810288 105.97821) (xy 141.679185 105.890609) (xy 141.679172 105.890602) (xy 141.533501 105.830264) + (xy 141.533489 105.830261) (xy 141.378845 105.7995) (xy 141.378842 105.7995) (xy 141.221158 105.7995) + (xy 141.221155 105.7995) (xy 141.06651 105.830261) (xy 141.066498 105.830264) (xy 140.920827 105.890602) + (xy 140.920814 105.890609) (xy 140.789711 105.97821) (xy 140.789706 105.978214) (xy 140.771389 105.996531) + (xy 140.710065 106.030015) (xy 140.640374 106.025029) (xy 140.584441 105.983156) (xy 140.580608 105.977739) + (xy 140.521789 105.889711) (xy 140.521786 105.889707) (xy 140.410292 105.778213) (xy 140.410288 105.77821) + (xy 140.279185 105.690609) (xy 140.279172 105.690602) (xy 140.133501 105.630264) (xy 140.133489 105.630261) + (xy 139.978845 105.5995) (xy 139.978842 105.5995) (xy 139.821158 105.5995) (xy 139.821155 105.5995) + (xy 139.666505 105.630261) (xy 139.666497 105.630264) (xy 139.598682 105.658353) (xy 139.529213 105.66582) + (xy 139.466734 105.634544) (xy 139.463551 105.631472) (xy 139.410292 105.578213) (xy 139.410288 105.57821) + (xy 139.279185 105.490609) (xy 139.279172 105.490602) (xy 139.133501 105.430264) (xy 139.133489 105.430261) + (xy 138.978845 105.3995) (xy 138.978842 105.3995) (xy 138.821158 105.3995) (xy 138.821155 105.3995) + (xy 138.66651 105.430261) (xy 138.666498 105.430264) (xy 138.520827 105.490602) (xy 138.520814 105.490609) + (xy 138.389711 105.57821) (xy 138.389707 105.578213) (xy 138.278213 105.689707) (xy 138.27821 105.689711) + (xy 138.190609 105.820814) (xy 138.190602 105.820827) (xy 138.130264 105.966498) (xy 138.130261 105.96651) + (xy 138.0995 106.121153) (xy 131.353232 106.121153) (xy 131.310292 106.078213) (xy 131.310288 106.07821) + (xy 131.179185 105.990609) (xy 131.179172 105.990602) (xy 131.033501 105.930264) (xy 131.033489 105.930261) + (xy 130.878845 105.8995) (xy 130.878842 105.8995) (xy 130.721158 105.8995) (xy 130.721155 105.8995) + (xy 130.56651 105.930261) (xy 130.566498 105.930264) (xy 130.420827 105.990602) (xy 130.420814 105.990609) + (xy 130.289711 106.07821) (xy 130.289707 106.078213) (xy 130.178213 106.189707) (xy 130.17821 106.189711) + (xy 130.090609 106.320814) (xy 130.090602 106.320827) (xy 130.030264 106.466498) (xy 130.030261 106.46651) + (xy 129.9995 106.621153) (xy 129.9995 106.778846) (xy 130.030261 106.933489) (xy 130.030264 106.933501) + (xy 130.090602 107.079172) (xy 130.090609 107.079185) (xy 130.17821 107.210288) (xy 130.178213 107.210292) + (xy 130.28024 107.312319) (xy 130.313725 107.373642) (xy 130.308741 107.443334) (xy 130.28024 107.487681) + (xy 130.202478 107.565442) (xy 130.202475 107.565446) (xy 130.114874 107.696549) (xy 130.114867 107.696562) + (xy 130.054529 107.842233) (xy 130.054526 107.842245) (xy 130.023765 107.996888) (xy 130.023765 108.154581) + (xy 130.054526 108.309224) (xy 130.054529 108.309236) (xy 130.097213 108.412286) (xy 130.104682 108.481756) + (xy 130.09202 108.518173) (xy 130.090608 108.520815) (xy 130.030264 108.666498) (xy 130.030261 108.66651) + (xy 129.9995 108.821153) (xy 129.9995 108.978846) (xy 130.023017 109.097075) (xy 130.01679 109.166667) + (xy 129.973927 109.221844) (xy 129.970291 109.224368) (xy 129.889711 109.27821) (xy 129.889707 109.278213) + (xy 129.778213 109.389707) (xy 129.77821 109.389711) (xy 129.690609 109.520814) (xy 129.690602 109.520827) + (xy 129.630264 109.666498) (xy 129.630261 109.66651) (xy 129.5995 109.821153) (xy 126.592084 109.821153) + (xy 126.598107 109.790875) (xy 126.598107 109.790874) (xy 126.6005 109.778844) (xy 126.6005 109.621155) + (xy 126.600499 109.621153) (xy 126.580734 109.521789) (xy 126.569737 109.466503) (xy 126.537929 109.389711) + (xy 126.509397 109.320827) (xy 126.50939 109.320814) (xy 126.421789 109.189711) (xy 126.421786 109.189707) + (xy 126.310292 109.078213) (xy 126.310288 109.07821) (xy 126.179185 108.990609) (xy 126.179172 108.990602) + (xy 126.033501 108.930264) (xy 126.033489 108.930261) (xy 125.878845 108.8995) (xy 125.878842 108.8995) + (xy 125.721158 108.8995) (xy 125.721155 108.8995) (xy 125.56651 108.930261) (xy 125.566498 108.930264) + (xy 125.420827 108.990602) (xy 125.420814 108.990609) (xy 125.289711 109.07821) (xy 125.289707 109.078213) + (xy 125.229857 109.138064) (xy 125.168534 109.171549) (xy 125.098842 109.166565) (xy 125.073285 109.153485) + (xy 124.979185 109.090609) (xy 124.979172 109.090602) (xy 124.833501 109.030264) (xy 124.833489 109.030261) + (xy 124.678845 108.9995) (xy 124.678842 108.9995) (xy 124.521158 108.9995) (xy 124.521155 108.9995) + (xy 124.36651 109.030261) (xy 124.366498 109.030264) (xy 124.220827 109.090602) (xy 124.220814 109.090609) + (xy 124.089711 109.17821) (xy 124.089707 109.178213) (xy 123.978213 109.289707) (xy 123.97821 109.289711) + (xy 123.890609 109.420814) (xy 123.890602 109.420827) (xy 123.830264 109.566498) (xy 123.830261 109.56651) + (xy 123.7995 109.721153) (xy 120.2505 109.721153) (xy 120.2505 106.98454) (xy 121.07343 106.98454) + (xy 121.07343 107.142233) (xy 121.104191 107.296876) (xy 121.104194 107.296888) (xy 121.164532 107.442559) + (xy 121.164539 107.442572) (xy 121.25214 107.573675) (xy 121.252143 107.573679) (xy 121.363637 107.685173) + (xy 121.363641 107.685176) (xy 121.494744 107.772777) (xy 121.494757 107.772784) (xy 121.585311 107.810292) + (xy 121.640433 107.833124) (xy 121.795083 107.863886) (xy 121.795086 107.863887) (xy 121.795088 107.863887) + (xy 121.952774 107.863887) (xy 121.952775 107.863886) (xy 122.107427 107.833124) (xy 122.253109 107.772781) + (xy 122.384219 107.685176) (xy 122.495719 107.573676) (xy 122.583324 107.442566) (xy 122.643667 107.296884) + (xy 122.67443 107.142229) (xy 122.67443 106.984545) (xy 122.67443 106.984542) (xy 122.674429 106.98454) + (xy 122.66182 106.921153) (xy 122.643667 106.82989) (xy 122.598102 106.719887) (xy 122.590634 106.650419) + (xy 122.601294 106.619772) (xy 122.600963 106.619635) (xy 122.663635 106.468328) (xy 122.663637 106.468324) + (xy 122.6944 106.313669) (xy 122.6944 106.155985) (xy 122.6944 106.155982) (xy 122.694399 106.15598) + (xy 122.67893 106.078213) (xy 122.663637 106.00133) (xy 122.654061 105.978211) (xy 122.603297 105.855654) + (xy 122.60329 105.855641) (xy 122.515689 105.724538) (xy 122.515686 105.724534) (xy 122.404192 105.61304) + (xy 122.404188 105.613037) (xy 122.273085 105.525436) (xy 122.273072 105.525429) (xy 122.162498 105.479629) + (xy 122.127397 105.46509) (xy 122.127389 105.465088) (xy 121.972745 105.434327) (xy 121.972742 105.434327) + (xy 121.815058 105.434327) (xy 121.815055 105.434327) (xy 121.66041 105.465088) (xy 121.660398 105.465091) + (xy 121.514727 105.525429) (xy 121.514714 105.525436) (xy 121.383611 105.613037) (xy 121.383607 105.61304) + (xy 121.272113 105.724534) (xy 121.27211 105.724538) (xy 121.184509 105.855641) (xy 121.184502 105.855654) + (xy 121.124164 106.001325) (xy 121.124161 106.001337) (xy 121.0934 106.15598) (xy 121.0934 106.313673) + (xy 121.124161 106.468316) (xy 121.124164 106.468328) (xy 121.169726 106.578325) (xy 121.177195 106.647794) + (xy 121.166538 106.678443) (xy 121.166867 106.67858) (xy 121.104194 106.829885) (xy 121.104191 106.829897) + (xy 121.07343 106.98454) (xy 120.2505 106.98454) (xy 120.2505 105.371155) (xy 127.3995 105.371155) + (xy 127.3995 105.528848) (xy 127.430261 105.683491) (xy 127.430264 105.683503) (xy 127.490602 105.829174) + (xy 127.490609 105.829187) (xy 127.57821 105.96029) (xy 127.578213 105.960294) (xy 127.689707 106.071788) + (xy 127.689711 106.071791) (xy 127.820814 106.159392) (xy 127.820827 106.159399) (xy 127.894008 106.189711) + (xy 127.966503 106.219739) (xy 128.121153 106.250501) (xy 128.121156 106.250502) (xy 128.121158 106.250502) + (xy 128.278844 106.250502) (xy 128.278845 106.250501) (xy 128.433497 106.219739) (xy 128.579179 106.159396) + (xy 128.710289 106.071791) (xy 128.821789 105.960291) (xy 128.909394 105.829181) (xy 128.969737 105.683499) + (xy 129.0005 105.528844) (xy 129.0005 105.37116) (xy 129.0005 105.371157) (xy 129.000499 105.371155) + (xy 128.969738 105.216512) (xy 128.969737 105.216505) (xy 128.969735 105.2165) (xy 128.909397 105.070829) + (xy 128.90939 105.070816) (xy 128.821789 104.939713) (xy 128.821786 104.939709) (xy 128.710292 104.828215) + (xy 128.710288 104.828212) (xy 128.579185 104.740611) (xy 128.579172 104.740604) (xy 128.433501 104.680266) + (xy 128.433489 104.680263) (xy 128.278845 104.649502) (xy 128.278842 104.649502) (xy 128.121158 104.649502) + (xy 128.121155 104.649502) (xy 127.96651 104.680263) (xy 127.966498 104.680266) (xy 127.820827 104.740604) + (xy 127.820814 104.740611) (xy 127.689711 104.828212) (xy 127.689707 104.828215) (xy 127.578213 104.939709) + (xy 127.57821 104.939713) (xy 127.490609 105.070816) (xy 127.490602 105.070829) (xy 127.430264 105.2165) + (xy 127.430261 105.216512) (xy 127.3995 105.371155) (xy 120.2505 105.371155) (xy 120.2505 102.721153) + (xy 121.4995 102.721153) (xy 121.4995 102.878846) (xy 121.530261 103.033489) (xy 121.530264 103.033501) + (xy 121.590602 103.179172) (xy 121.590609 103.179185) (xy 121.67821 103.310288) (xy 121.678213 103.310292) + (xy 121.789707 103.421786) (xy 121.789715 103.421792) (xy 121.848995 103.461402) (xy 121.893801 103.515014) + (xy 121.902508 103.584339) (xy 121.892194 103.614885) (xy 121.892937 103.615193) (xy 121.830264 103.766498) + (xy 121.830261 103.76651) (xy 121.7995 103.921153) (xy 121.7995 104.078846) (xy 121.830261 104.233489) + (xy 121.830264 104.233501) (xy 121.890602 104.379172) (xy 121.890609 104.379185) (xy 121.97821 104.510288) + (xy 121.978213 104.510292) (xy 122.089707 104.621786) (xy 122.089711 104.621789) (xy 122.220814 104.70939) + (xy 122.220827 104.709397) (xy 122.366498 104.769735) (xy 122.366503 104.769737) (xy 122.521153 104.800499) + (xy 122.521156 104.8005) (xy 122.521158 104.8005) (xy 122.678844 104.8005) (xy 122.678845 104.800499) + (xy 122.833497 104.769737) (xy 122.979179 104.709394) (xy 123.110289 104.621789) (xy 123.221789 104.510289) + (xy 123.309394 104.379179) (xy 123.369737 104.233497) (xy 123.4005 104.078842) (xy 123.4005 103.921158) + (xy 123.4005 103.921155) (xy 123.400499 103.921153) (xy 123.369738 103.76651) (xy 123.369737 103.766503) + (xy 123.309794 103.621786) (xy 123.309397 103.620827) (xy 123.30939 103.620814) (xy 123.221789 103.489711) + (xy 123.221786 103.489707) (xy 123.110292 103.378213) (xy 123.110288 103.37821) (xy 123.051003 103.338597) + (xy 123.006198 103.284985) (xy 122.997491 103.21566) (xy 123.007811 103.185117) (xy 123.007063 103.184808) + (xy 123.069735 103.033501) (xy 123.069737 103.033497) (xy 123.092083 102.921158) (xy 123.092084 102.921153) + (xy 136.999498 102.921153) (xy 136.999498 103.078846) (xy 137.030259 103.233489) (xy 137.030262 103.233501) + (xy 137.0906 103.379172) (xy 137.090607 103.379185) (xy 137.178208 103.510288) (xy 137.178211 103.510292) + (xy 137.289705 103.621786) (xy 137.289709 103.621789) (xy 137.420812 103.70939) (xy 137.420825 103.709397) + (xy 137.558681 103.766498) (xy 137.566501 103.769737) (xy 137.721151 103.800499) (xy 137.721154 103.8005) + (xy 137.721156 103.8005) (xy 137.878842 103.8005) (xy 137.878843 103.800499) (xy 138.033495 103.769737) + (xy 138.179177 103.709394) (xy 138.310287 103.621789) (xy 138.421787 103.510289) (xy 138.509392 103.379179) + (xy 138.569735 103.233497) (xy 138.600498 103.078842) (xy 138.600498 102.921158) (xy 138.600498 102.921155) + (xy 138.600497 102.921153) (xy 138.594474 102.890874) (xy 138.569735 102.766503) (xy 138.550953 102.721158) + (xy 138.509395 102.620827) (xy 138.509388 102.620814) (xy 138.421787 102.489711) (xy 138.421784 102.489707) + (xy 138.31029 102.378213) (xy 138.310286 102.37821) (xy 138.224895 102.321153) (xy 141.7995 102.321153) + (xy 141.7995 102.478846) (xy 141.830261 102.633489) (xy 141.830264 102.633501) (xy 141.890602 102.779172) + (xy 141.890609 102.779185) (xy 141.97821 102.910288) (xy 141.978213 102.910292) (xy 142.089707 103.021786) + (xy 142.089711 103.021789) (xy 142.220814 103.10939) (xy 142.220827 103.109397) (xy 142.366498 103.169735) + (xy 142.366503 103.169737) (xy 142.521153 103.200499) (xy 142.521156 103.2005) (xy 142.521158 103.2005) + (xy 142.678844 103.2005) (xy 142.678845 103.200499) (xy 142.833497 103.169737) (xy 142.979179 103.109394) + (xy 143.110289 103.021789) (xy 143.221789 102.910289) (xy 143.309394 102.779179) (xy 143.369737 102.633497) + (xy 143.4005 102.478842) (xy 143.4005 102.321158) (xy 143.4005 102.321155) (xy 143.400499 102.321153) + (xy 143.382419 102.230261) (xy 143.369737 102.166503) (xy 143.338298 102.090602) (xy 143.309397 102.020827) + (xy 143.30939 102.020814) (xy 143.221789 101.889711) (xy 143.221786 101.889707) (xy 143.110292 101.778213) + (xy 143.110288 101.77821) (xy 142.979185 101.690609) (xy 142.979172 101.690602) (xy 142.833501 101.630264) + (xy 142.833489 101.630261) (xy 142.678845 101.5995) (xy 142.678842 101.5995) (xy 142.521158 101.5995) + (xy 142.521155 101.5995) (xy 142.36651 101.630261) (xy 142.366498 101.630264) (xy 142.220827 101.690602) + (xy 142.220814 101.690609) (xy 142.089711 101.77821) (xy 142.089707 101.778213) (xy 141.978213 101.889707) + (xy 141.97821 101.889711) (xy 141.890609 102.020814) (xy 141.890602 102.020827) (xy 141.830264 102.166498) + (xy 141.830261 102.16651) (xy 141.7995 102.321153) (xy 138.224895 102.321153) (xy 138.179183 102.290609) + (xy 138.17917 102.290602) (xy 138.033499 102.230264) (xy 138.033487 102.230261) (xy 137.878843 102.1995) + (xy 137.87884 102.1995) (xy 137.721156 102.1995) (xy 137.721153 102.1995) (xy 137.566508 102.230261) + (xy 137.566496 102.230264) (xy 137.420825 102.290602) (xy 137.420812 102.290609) (xy 137.289709 102.37821) + (xy 137.289705 102.378213) (xy 137.178211 102.489707) (xy 137.178208 102.489711) (xy 137.090607 102.620814) + (xy 137.0906 102.620827) (xy 137.030262 102.766498) (xy 137.030259 102.76651) (xy 136.999498 102.921153) + (xy 123.092084 102.921153) (xy 123.098107 102.890875) (xy 123.098107 102.890874) (xy 123.1005 102.878844) + (xy 123.1005 102.721155) (xy 123.100499 102.721153) (xy 123.080543 102.620827) (xy 123.069737 102.566503) + (xy 123.037929 102.489711) (xy 123.009397 102.420827) (xy 123.00939 102.420814) (xy 122.921789 102.289711) + (xy 122.921786 102.289707) (xy 122.810292 102.178213) (xy 122.810288 102.17821) (xy 122.679185 102.090609) + (xy 122.679172 102.090602) (xy 122.533501 102.030264) (xy 122.533489 102.030261) (xy 122.378845 101.9995) + (xy 122.378842 101.9995) (xy 122.221158 101.9995) (xy 122.221155 101.9995) (xy 122.06651 102.030261) + (xy 122.066498 102.030264) (xy 121.920827 102.090602) (xy 121.920814 102.090609) (xy 121.789711 102.17821) + (xy 121.789707 102.178213) (xy 121.678213 102.289707) (xy 121.67821 102.289711) (xy 121.590609 102.420814) + (xy 121.590602 102.420827) (xy 121.530264 102.566498) (xy 121.530261 102.56651) (xy 121.4995 102.721153) + (xy 120.2505 102.721153) (xy 120.2505 100.321153) (xy 125.7995 100.321153) (xy 125.7995 100.478846) + (xy 125.830261 100.633489) (xy 125.830264 100.633501) (xy 125.890602 100.779172) (xy 125.890609 100.779185) + (xy 125.97821 100.910288) (xy 125.978213 100.910292) (xy 126.089707 101.021786) (xy 126.089711 101.021789) + (xy 126.220814 101.10939) (xy 126.220827 101.109397) (xy 126.366498 101.169735) (xy 126.366503 101.169737) + (xy 126.521153 101.200499) (xy 126.521156 101.2005) (xy 126.521158 101.2005) (xy 126.678844 101.2005) + (xy 126.678845 101.200499) (xy 126.833497 101.169737) (xy 126.979179 101.109394) (xy 127.110289 101.021789) + (xy 127.221789 100.910289) (xy 127.309394 100.779179) (xy 127.369737 100.633497) (xy 127.4005 100.478842) + (xy 127.4005 100.321158) (xy 127.4005 100.321155) (xy 127.400499 100.321153) (xy 127.387716 100.256891) + (xy 127.369737 100.166503) (xy 127.328314 100.066498) (xy 127.309397 100.020827) (xy 127.309393 100.02082) + (xy 127.309389 100.020814) (xy 127.2888 99.99) (xy 127.267923 99.923324) (xy 127.286407 99.855944) + (xy 127.338386 99.809253) (xy 127.407356 99.798077) (xy 127.416084 99.79949) (xy 127.421158 99.8005) + (xy 127.42116 99.8005) (xy 127.578844 99.8005) (xy 127.578845 99.800499) (xy 127.733497 99.769737) + (xy 127.850923 99.721097) (xy 127.920392 99.713629) (xy 127.982871 99.744904) (xy 128.018523 99.804993) + (xy 128.016029 99.874818) (xy 128.001478 99.904549) (xy 127.990608 99.920816) (xy 127.990602 99.920827) + (xy 127.930264 100.066498) (xy 127.930261 100.06651) (xy 127.8995 100.221153) (xy 127.8995 100.378846) + (xy 127.930261 100.533489) (xy 127.930264 100.533501) (xy 127.990602 100.679172) (xy 127.990609 100.679185) + (xy 128.07821 100.810288) (xy 128.078213 100.810292) (xy 128.189707 100.921786) (xy 128.189711 100.921789) + (xy 128.320814 101.00939) (xy 128.320827 101.009397) (xy 128.441518 101.059388) (xy 128.466503 101.069737) + (xy 128.621153 101.100499) (xy 128.621156 101.1005) (xy 128.621158 101.1005) (xy 128.778844 101.1005) + (xy 128.778845 101.100499) (xy 128.933497 101.069737) (xy 129.079179 101.009394) (xy 129.210289 100.921789) + (xy 129.321789 100.810289) (xy 129.409394 100.679179) (xy 129.469737 100.533497) (xy 129.490555 100.428841) + (xy 129.492084 100.421153) (xy 130.9995 100.421153) (xy 130.9995 100.578846) (xy 131.030261 100.733489) + (xy 131.030264 100.733501) (xy 131.090602 100.879172) (xy 131.090609 100.879185) (xy 131.17821 101.010288) + (xy 131.178213 101.010292) (xy 131.289707 101.121786) (xy 131.289711 101.121789) (xy 131.420814 101.20939) + (xy 131.420827 101.209397) (xy 131.566498 101.269735) (xy 131.566503 101.269737) (xy 131.721153 101.300499) + (xy 131.721156 101.3005) (xy 131.721158 101.3005) (xy 131.878844 101.3005) (xy 131.878845 101.300499) + (xy 132.033497 101.269737) (xy 132.160626 101.217079) (xy 132.179172 101.209397) (xy 132.179172 101.209396) + (xy 132.179179 101.209394) (xy 132.310289 101.121789) (xy 132.360469 101.071609) (xy 132.421792 101.038123) + (xy 132.491483 101.043107) (xy 132.547417 101.084978) (xy 132.562712 101.111837) (xy 132.590602 101.179172) + (xy 132.590609 101.179185) (xy 132.67821 101.310288) (xy 132.678213 101.310292) (xy 132.789707 101.421786) + (xy 132.789711 101.421789) (xy 132.920814 101.50939) (xy 132.920827 101.509397) (xy 133.066498 101.569735) + (xy 133.066503 101.569737) (xy 133.216131 101.5995) (xy 133.221153 101.600499) (xy 133.221156 101.6005) + (xy 133.221158 101.6005) (xy 133.378844 101.6005) (xy 133.378845 101.600499) (xy 133.533497 101.569737) + (xy 133.679179 101.509394) (xy 133.810289 101.421789) (xy 133.921789 101.310289) (xy 134.009394 101.179179) + (xy 134.059013 101.059388) (xy 135.361265 101.059388) (xy 135.361265 101.217081) (xy 135.392026 101.371724) + (xy 135.392029 101.371736) (xy 135.452367 101.517407) (xy 135.452374 101.51742) (xy 135.539975 101.648523) + (xy 135.539978 101.648527) (xy 135.651472 101.760021) (xy 135.651476 101.760024) (xy 135.782579 101.847625) + (xy 135.782592 101.847632) (xy 135.928263 101.90797) (xy 135.928268 101.907972) (xy 136.082918 101.938734) + (xy 136.082921 101.938735) (xy 136.082923 101.938735) (xy 136.240609 101.938735) (xy 136.24061 101.938734) + (xy 136.395262 101.907972) (xy 136.540944 101.847629) (xy 136.672054 101.760024) (xy 136.783554 101.648524) + (xy 136.871159 101.517414) (xy 136.931502 101.371732) (xy 136.962265 101.217077) (xy 136.962265 101.059393) + (xy 136.962265 101.05939) (xy 136.962264 101.059388) (xy 136.952498 101.010292) (xy 136.931502 100.904738) + (xy 136.9315 100.904733) (xy 136.871162 100.759062) (xy 136.871155 100.759049) (xy 136.783554 100.627946) + (xy 136.783551 100.627942) (xy 136.672057 100.516448) (xy 136.672053 100.516445) (xy 136.54095 100.428844) + (xy 136.540937 100.428837) (xy 136.395266 100.368499) (xy 136.395256 100.368496) (xy 136.24061 100.337735) + (xy 136.240607 100.337735) (xy 136.082923 100.337735) (xy 136.08292 100.337735) (xy 135.928275 100.368496) + (xy 135.928263 100.368499) (xy 135.782592 100.428837) (xy 135.782579 100.428844) (xy 135.651476 100.516445) + (xy 135.651472 100.516448) (xy 135.539978 100.627942) (xy 135.539975 100.627946) (xy 135.452374 100.759049) + (xy 135.452367 100.759062) (xy 135.392029 100.904733) (xy 135.392026 100.904745) (xy 135.361265 101.059388) + (xy 134.059013 101.059388) (xy 134.069737 101.033497) (xy 134.100433 100.879179) (xy 134.1005 100.878844) + (xy 134.1005 100.721155) (xy 134.100499 100.721153) (xy 134.069738 100.56651) (xy 134.069737 100.566503) + (xy 134.049003 100.516446) (xy 134.009397 100.420827) (xy 134.00939 100.420814) (xy 133.921789 100.289711) + (xy 133.921786 100.289707) (xy 133.853232 100.221153) (xy 139.5995 100.221153) (xy 139.5995 100.378846) + (xy 139.630261 100.533489) (xy 139.630264 100.533501) (xy 139.690602 100.679172) (xy 139.690609 100.679185) + (xy 139.77821 100.810288) (xy 139.778213 100.810292) (xy 139.889707 100.921786) (xy 139.889711 100.921789) + (xy 140.020814 101.00939) (xy 140.020827 101.009397) (xy 140.141518 101.059388) (xy 140.166503 101.069737) + (xy 140.321153 101.100499) (xy 140.321156 101.1005) (xy 140.321158 101.1005) (xy 140.478844 101.1005) + (xy 140.478845 101.100499) (xy 140.633497 101.069737) (xy 140.779179 101.009394) (xy 140.910289 100.921789) + (xy 141.021789 100.810289) (xy 141.109394 100.679179) (xy 141.169737 100.533497) (xy 141.2005 100.378842) + (xy 141.2005 100.221158) (xy 141.2005 100.221155) (xy 141.200499 100.221153) (xy 141.180543 100.120827) + (xy 141.169737 100.066503) (xy 141.169735 100.066498) (xy 141.109397 99.920827) (xy 141.10939 99.920814) + (xy 141.021789 99.789711) (xy 141.021786 99.789707) (xy 140.910292 99.678213) (xy 140.910288 99.67821) + (xy 140.779185 99.590609) (xy 140.779172 99.590602) (xy 140.633501 99.530264) (xy 140.633489 99.530261) + (xy 140.478845 99.4995) (xy 140.478842 99.4995) (xy 140.321158 99.4995) (xy 140.321155 99.4995) + (xy 140.16651 99.530261) (xy 140.166498 99.530264) (xy 140.020827 99.590602) (xy 140.020814 99.590609) + (xy 139.889711 99.67821) (xy 139.889707 99.678213) (xy 139.778213 99.789707) (xy 139.77821 99.789711) + (xy 139.690609 99.920814) (xy 139.690602 99.920827) (xy 139.630264 100.066498) (xy 139.630261 100.06651) + (xy 139.5995 100.221153) (xy 133.853232 100.221153) (xy 133.810292 100.178213) (xy 133.810288 100.17821) + (xy 133.679185 100.090609) (xy 133.679172 100.090602) (xy 133.533501 100.030264) (xy 133.533489 100.030261) + (xy 133.378845 99.9995) (xy 133.378842 99.9995) (xy 133.221158 99.9995) (xy 133.221155 99.9995) + (xy 133.06651 100.030261) (xy 133.066498 100.030264) (xy 132.920827 100.090602) (xy 132.920814 100.090609) + (xy 132.789711 100.17821) (xy 132.789706 100.178214) (xy 132.739528 100.228392) (xy 132.678205 100.261876) + (xy 132.608513 100.256891) (xy 132.55258 100.21502) (xy 132.537289 100.188166) (xy 132.509394 100.120821) + (xy 132.50939 100.120814) (xy 132.421789 99.989711) (xy 132.421786 99.989707) (xy 132.310292 99.878213) + (xy 132.310288 99.87821) (xy 132.179185 99.790609) (xy 132.179172 99.790602) (xy 132.033501 99.730264) + (xy 132.033489 99.730261) (xy 131.878845 99.6995) (xy 131.878842 99.6995) (xy 131.721158 99.6995) + (xy 131.721155 99.6995) (xy 131.56651 99.730261) (xy 131.566498 99.730264) (xy 131.420827 99.790602) + (xy 131.420814 99.790609) (xy 131.289711 99.87821) (xy 131.289707 99.878213) (xy 131.178213 99.989707) + (xy 131.17821 99.989711) (xy 131.090609 100.120814) (xy 131.090602 100.120827) (xy 131.030264 100.266498) + (xy 131.030261 100.26651) (xy 130.9995 100.421153) (xy 129.492084 100.421153) (xy 129.498107 100.390875) + (xy 129.498107 100.390874) (xy 129.5005 100.378844) (xy 129.5005 100.221155) (xy 129.500499 100.221153) + (xy 129.480543 100.120827) (xy 129.469737 100.066503) (xy 129.469735 100.066498) (xy 129.409397 99.920827) + (xy 129.40939 99.920814) (xy 129.321789 99.789711) (xy 129.321786 99.789707) (xy 129.210292 99.678213) + (xy 129.210288 99.67821) (xy 129.079185 99.590609) (xy 129.079172 99.590602) (xy 128.933501 99.530264) + (xy 128.933489 99.530261) (xy 128.778845 99.4995) (xy 128.778842 99.4995) (xy 128.621158 99.4995) + (xy 128.621155 99.4995) (xy 128.46651 99.530261) (xy 128.466503 99.530263) (xy 128.349075 99.578902) + (xy 128.279606 99.58637) (xy 128.217127 99.555094) (xy 128.181475 99.495005) (xy 128.18397 99.42518) + (xy 128.198525 99.395445) (xy 128.20939 99.379185) (xy 128.20939 99.379184) (xy 128.209394 99.379179) + (xy 128.269737 99.233497) (xy 128.3005 99.078842) (xy 128.3005 98.921158) (xy 128.3005 98.921155) + (xy 128.300499 98.921153) (xy 135.0995 98.921153) (xy 135.0995 99.078846) (xy 135.130261 99.233489) + (xy 135.130264 99.233501) (xy 135.190602 99.379172) (xy 135.190609 99.379185) (xy 135.27821 99.510288) + (xy 135.278213 99.510292) (xy 135.389707 99.621786) (xy 135.389711 99.621789) (xy 135.520814 99.70939) + (xy 135.520827 99.709397) (xy 135.60655 99.744904) (xy 135.666503 99.769737) (xy 135.808977 99.798077) + (xy 135.821153 99.800499) (xy 135.821156 99.8005) (xy 135.821158 99.8005) (xy 135.978844 99.8005) + (xy 135.978845 99.800499) (xy 136.133497 99.769737) (xy 136.279179 99.709394) (xy 136.410289 99.621789) + (xy 136.521789 99.510289) (xy 136.609394 99.379179) (xy 136.669737 99.233497) (xy 136.7005 99.078842) + (xy 136.7005 98.921158) (xy 136.7005 98.921155) (xy 136.700499 98.921153) (xy 136.689455 98.865633) + (xy 136.669737 98.766503) (xy 136.633427 98.678842) (xy 136.609397 98.620827) (xy 136.60939 98.620814) + (xy 136.521789 98.489711) (xy 136.521786 98.489707) (xy 136.410292 98.378213) (xy 136.410288 98.37821) + (xy 136.279185 98.290609) (xy 136.279172 98.290602) (xy 136.133501 98.230264) (xy 136.133489 98.230261) + (xy 135.978845 98.1995) (xy 135.978842 98.1995) (xy 135.821158 98.1995) (xy 135.821155 98.1995) + (xy 135.66651 98.230261) (xy 135.666498 98.230264) (xy 135.520827 98.290602) (xy 135.520814 98.290609) + (xy 135.389711 98.37821) (xy 135.389707 98.378213) (xy 135.278213 98.489707) (xy 135.27821 98.489711) + (xy 135.190609 98.620814) (xy 135.190602 98.620827) (xy 135.130264 98.766498) (xy 135.130261 98.76651) + (xy 135.0995 98.921153) (xy 128.300499 98.921153) (xy 128.289455 98.865633) (xy 128.269737 98.766503) + (xy 128.230572 98.671951) (xy 128.223104 98.602483) (xy 128.254379 98.540004) (xy 128.314468 98.504352) + (xy 128.345134 98.5005) (xy 128.378844 98.5005) (xy 128.378845 98.500499) (xy 128.533497 98.469737) + (xy 128.679179 98.409394) (xy 128.810289 98.321789) (xy 128.921789 98.210289) (xy 129.009394 98.079179) + (xy 129.069737 97.933497) (xy 129.1005 97.778842) (xy 129.1005 97.621158) (xy 129.1005 97.621155) + (xy 129.100499 97.621153) (xy 129.086136 97.548946) (xy 129.069737 97.466503) (xy 129.060732 97.444762) + (xy 129.057544 97.415113) (xy 129.051824 97.385843) (xy 129.053849 97.380745) (xy 129.053263 97.375293) + (xy 129.06661 97.348629) (xy 129.067594 97.346153) (xy 130.0495 97.346153) (xy 130.0495 97.503846) + (xy 130.080261 97.658489) (xy 130.080264 97.658501) (xy 130.140602 97.804172) (xy 130.140609 97.804185) + (xy 130.22821 97.935288) (xy 130.228213 97.935292) (xy 130.339707 98.046786) (xy 130.339711 98.046789) + (xy 130.470814 98.13439) (xy 130.470827 98.134397) (xy 130.57971 98.179497) (xy 130.616503 98.194737) + (xy 130.751019 98.221494) (xy 130.771153 98.225499) (xy 130.771156 98.2255) (xy 130.771158 98.2255) + (xy 130.928844 98.2255) (xy 130.928845 98.225499) (xy 131.083497 98.194737) (xy 131.229179 98.134394) + (xy 131.360289 98.046789) (xy 131.471789 97.935289) (xy 131.559394 97.804179) (xy 131.570625 97.777066) + (xy 131.601059 97.703589) (xy 131.619737 97.658497) (xy 131.6505 97.503842) (xy 131.6505 97.346158) + (xy 131.6505 97.346155) (xy 131.650499 97.346153) (xy 131.623474 97.210292) (xy 131.619737 97.191503) + (xy 131.618993 97.189707) (xy 131.559397 97.045827) (xy 131.55939 97.045814) (xy 131.471789 96.914711) + (xy 131.471786 96.914707) (xy 131.360292 96.803213) (xy 131.360288 96.80321) (xy 131.229185 96.715609) + (xy 131.229172 96.715602) (xy 131.083501 96.655264) (xy 131.083489 96.655261) (xy 130.928845 96.6245) + (xy 130.928842 96.6245) (xy 130.771158 96.6245) (xy 130.771155 96.6245) (xy 130.61651 96.655261) + (xy 130.616498 96.655264) (xy 130.470827 96.715602) (xy 130.470814 96.715609) (xy 130.339711 96.80321) + (xy 130.339707 96.803213) (xy 130.228213 96.914707) (xy 130.22821 96.914711) (xy 130.140609 97.045814) + (xy 130.140602 97.045827) (xy 130.080264 97.191498) (xy 130.080261 97.19151) (xy 130.0495 97.346153) + (xy 129.067594 97.346153) (xy 129.077624 97.320911) (xy 129.082967 97.315952) (xy 129.084539 97.312814) + (xy 129.103105 97.296489) (xy 129.10472 97.295332) (xy 129.164669 97.255276) (xy 129.255276 97.164669) + (xy 129.326465 97.058127) (xy 129.375501 96.939744) (xy 129.387658 96.878628) (xy 129.4005 96.814071) + (xy 129.4005 96.685928) (xy 129.375502 96.560261) (xy 129.375501 96.56026) (xy 129.375501 96.560256) + (xy 129.336665 96.466498) (xy 129.326466 96.441875) (xy 129.326461 96.441866) (xy 129.255276 96.335331) + (xy 129.251411 96.330621) (xy 129.253045 96.329279) (xy 129.224148 96.276389) (xy 129.229114 96.206696) + (xy 129.252514 96.170284) (xy 129.251411 96.169379) (xy 129.255271 96.164673) (xy 129.255276 96.164669) + (xy 129.326465 96.058127) (xy 129.375501 95.939744) (xy 129.383682 95.898615) (xy 129.4005 95.814071) + (xy 129.4005 95.685928) (xy 129.375502 95.560261) (xy 129.375501 95.56026) (xy 129.375501 95.560256) + (xy 129.326465 95.441873) (xy 129.326464 95.441872) (xy 129.326461 95.441866) (xy 129.255276 95.335331) + (xy 129.255273 95.335327) (xy 129.18577 95.265824) (xy 129.161378 95.221153) (xy 131.1995 95.221153) + (xy 131.1995 95.378846) (xy 131.230261 95.533489) (xy 131.230264 95.533501) (xy 131.290602 95.679172) + (xy 131.290609 95.679185) (xy 131.37821 95.810288) (xy 131.378213 95.810292) (xy 131.489707 95.921786) + (xy 131.489711 95.921789) (xy 131.620814 96.00939) (xy 131.620827 96.009397) (xy 131.738488 96.058133) + (xy 131.766503 96.069737) (xy 131.921153 96.100499) (xy 131.921156 96.1005) (xy 131.921158 96.1005) + (xy 132.078844 96.1005) (xy 132.078845 96.100499) (xy 132.233497 96.069737) (xy 132.379179 96.009394) + (xy 132.510289 95.921789) (xy 132.621789 95.810289) (xy 132.709394 95.679179) (xy 132.709395 95.679176) + (xy 132.709397 95.679173) (xy 132.712719 95.671153) (xy 134.4495 95.671153) (xy 134.4495 95.828846) + (xy 134.480261 95.983489) (xy 134.480264 95.983501) (xy 134.540602 96.129172) (xy 134.540609 96.129185) + (xy 134.62821 96.260288) (xy 134.628213 96.260292) (xy 134.739707 96.371786) (xy 134.73971 96.371788) + (xy 134.739711 96.371789) (xy 134.765219 96.388833) (xy 134.777289 96.396898) (xy 134.822093 96.450511) + (xy 134.8308 96.519836) (xy 134.800645 96.582863) (xy 134.777289 96.603102) (xy 134.739707 96.628213) + (xy 134.628213 96.739707) (xy 134.62821 96.739711) (xy 134.540609 96.870814) (xy 134.540602 96.870827) + (xy 134.480264 97.016498) (xy 134.480261 97.01651) (xy 134.4495 97.171153) (xy 134.4495 97.328846) + (xy 134.480261 97.483489) (xy 134.480264 97.483501) (xy 134.540602 97.629172) (xy 134.540609 97.629185) + (xy 134.62821 97.760288) (xy 134.628213 97.760292) (xy 134.739707 97.871786) (xy 134.739711 97.871789) + (xy 134.870814 97.95939) (xy 134.870827 97.959397) (xy 135.016498 98.019735) (xy 135.016503 98.019737) + (xy 135.152487 98.046786) (xy 135.171153 98.050499) (xy 135.171156 98.0505) (xy 135.171158 98.0505) + (xy 135.328844 98.0505) (xy 135.328845 98.050499) (xy 135.483497 98.019737) (xy 135.629179 97.959394) + (xy 135.760289 97.871789) (xy 135.871789 97.760289) (xy 135.931348 97.671153) (xy 136.6995 97.671153) + (xy 136.6995 97.828846) (xy 136.730261 97.983489) (xy 136.730264 97.983501) (xy 136.790602 98.129172) + (xy 136.790609 98.129185) (xy 136.87821 98.260288) (xy 136.878213 98.260292) (xy 136.989707 98.371786) + (xy 136.989711 98.371789) (xy 137.120814 98.45939) (xy 137.120827 98.459397) (xy 137.22006 98.5005) + (xy 137.266503 98.519737) (xy 137.421153 98.550499) (xy 137.421156 98.5505) (xy 137.421158 98.5505) + (xy 137.578844 98.5505) (xy 137.578845 98.550499) (xy 137.733497 98.519737) (xy 137.879179 98.459394) + (xy 138.010289 98.371789) (xy 138.121789 98.260289) (xy 138.197966 98.146282) (xy 139.085387 98.146282) + (xy 139.085387 98.303975) (xy 139.116148 98.458618) (xy 139.116151 98.45863) (xy 139.176489 98.604301) + (xy 139.176496 98.604314) (xy 139.264097 98.735417) (xy 139.2641 98.735421) (xy 139.375594 98.846915) + (xy 139.375598 98.846918) (xy 139.506701 98.934519) (xy 139.506714 98.934526) (xy 139.614532 98.979185) + (xy 139.65239 98.994866) (xy 139.80704 99.025628) (xy 139.807043 99.025629) (xy 139.807045 99.025629) + (xy 139.964731 99.025629) (xy 139.964732 99.025628) (xy 140.119384 98.994866) (xy 140.265066 98.934523) + (xy 140.396176 98.846918) (xy 140.507676 98.735418) (xy 140.595281 98.604308) (xy 140.655624 98.458626) + (xy 140.686387 98.303971) (xy 140.686387 98.146287) (xy 140.686387 98.146284) (xy 140.686386 98.146282) + (xy 140.676285 98.095496) (xy 140.672684 98.077392) (xy 146.233858 98.077392) (xy 146.233858 98.235085) + (xy 146.264619 98.389728) (xy 146.264622 98.38974) (xy 146.32496 98.535411) (xy 146.324967 98.535424) + (xy 146.412568 98.666527) (xy 146.412571 98.666531) (xy 146.524065 98.778025) (xy 146.524069 98.778028) + (xy 146.655172 98.865629) (xy 146.655185 98.865636) (xy 146.789217 98.921153) (xy 146.800861 98.925976) + (xy 146.860027 98.937745) (xy 146.928316 98.951329) (xy 146.990227 98.983714) (xy 147.007227 99.004055) + (xy 147.07821 99.110288) (xy 147.078213 99.110292) (xy 147.189707 99.221786) (xy 147.189711 99.221789) + (xy 147.320814 99.30939) (xy 147.320827 99.309397) (xy 147.466498 99.369735) (xy 147.466503 99.369737) + (xy 147.595745 99.395445) (xy 147.621153 99.400499) (xy 147.621156 99.4005) (xy 147.621158 99.4005) + (xy 147.778844 99.4005) (xy 147.778845 99.400499) (xy 147.933497 99.369737) (xy 148.079179 99.309394) + (xy 148.210289 99.221789) (xy 148.321789 99.110289) (xy 148.409394 98.979179) (xy 148.469737 98.833497) + (xy 148.5005 98.678842) (xy 148.5005 98.521158) (xy 148.5005 98.521155) (xy 148.500499 98.521153) + (xy 148.488062 98.45863) (xy 148.469737 98.366503) (xy 148.451215 98.321786) (xy 148.409397 98.220827) + (xy 148.40939 98.220814) (xy 148.321789 98.089711) (xy 148.321786 98.089707) (xy 148.210292 97.978213) + (xy 148.210288 97.97821) (xy 148.079185 97.890609) (xy 148.079172 97.890602) (xy 147.933501 97.830264) + (xy 147.933491 97.830261) (xy 147.80604 97.804909) (xy 147.744129 97.772524) (xy 147.72713 97.752183) + (xy 147.656147 97.64595) (xy 147.652282 97.64124) (xy 147.654018 97.639815) (xy 147.625341 97.587335) + (xy 147.630304 97.517642) (xy 147.658816 97.473261) (xy 147.671789 97.460289) (xy 147.759394 97.329179) + (xy 147.762854 97.320827) (xy 147.790005 97.255276) (xy 147.819737 97.183497) (xy 147.8505 97.028842) + (xy 147.8505 96.871158) (xy 147.8505 96.871155) (xy 147.850499 96.871153) (xy 147.840402 96.820391) + (xy 147.819737 96.716503) (xy 147.819367 96.715609) (xy 147.759397 96.570827) (xy 147.75939 96.570814) + (xy 147.671789 96.439711) (xy 147.671786 96.439707) (xy 147.560292 96.328213) (xy 147.560288 96.32821) + (xy 147.429185 96.240609) (xy 147.429172 96.240602) (xy 147.283501 96.180264) (xy 147.283489 96.180261) + (xy 147.128845 96.1495) (xy 147.128842 96.1495) (xy 146.971158 96.1495) (xy 146.971155 96.1495) + (xy 146.81651 96.180261) (xy 146.816498 96.180264) (xy 146.670827 96.240602) (xy 146.670814 96.240609) + (xy 146.539711 96.32821) (xy 146.539707 96.328213) (xy 146.428213 96.439707) (xy 146.42821 96.439711) + (xy 146.340609 96.570814) (xy 146.340602 96.570827) (xy 146.280264 96.716498) (xy 146.280261 96.71651) + (xy 146.2495 96.871153) (xy 146.2495 97.028846) (xy 146.280261 97.183489) (xy 146.280264 97.183501) + (xy 146.340602 97.329172) (xy 146.340609 97.329185) (xy 146.42821 97.460288) (xy 146.432076 97.464999) + (xy 146.430344 97.466419) (xy 146.459023 97.51894) (xy 146.454039 97.588632) (xy 146.425543 97.632974) + (xy 146.412572 97.645946) (xy 146.412566 97.645953) (xy 146.324967 97.777053) (xy 146.32496 97.777066) + (xy 146.264622 97.922737) (xy 146.264619 97.922749) (xy 146.233858 98.077392) (xy 140.672684 98.077392) + (xy 140.655625 97.991637) (xy 140.655624 97.991636) (xy 140.655624 97.991632) (xy 140.650065 97.978211) + (xy 140.595284 97.845956) (xy 140.595277 97.845943) (xy 140.507676 97.71484) (xy 140.507673 97.714836) + (xy 140.396179 97.603342) (xy 140.396175 97.603339) (xy 140.265072 97.515738) (xy 140.265059 97.515731) + (xy 140.119388 97.455393) (xy 140.119376 97.45539) (xy 139.964732 97.424629) (xy 139.964729 97.424629) + (xy 139.807045 97.424629) (xy 139.807042 97.424629) (xy 139.652397 97.45539) (xy 139.652385 97.455393) + (xy 139.506714 97.515731) (xy 139.506701 97.515738) (xy 139.375598 97.603339) (xy 139.375594 97.603342) + (xy 139.2641 97.714836) (xy 139.264097 97.71484) (xy 139.176496 97.845943) (xy 139.176489 97.845956) + (xy 139.116151 97.991627) (xy 139.116148 97.991639) (xy 139.085387 98.146282) (xy 138.197966 98.146282) + (xy 138.209394 98.129179) (xy 138.269737 97.983497) (xy 138.3005 97.828842) (xy 138.3005 97.671158) + (xy 138.3005 97.671155) (xy 138.300499 97.671153) (xy 138.27619 97.548944) (xy 138.269737 97.516503) + (xy 138.264493 97.503842) (xy 138.209397 97.370827) (xy 138.20939 97.370814) (xy 138.121789 97.239711) + (xy 138.121786 97.239707) (xy 138.010292 97.128213) (xy 138.010288 97.12821) (xy 137.879185 97.040609) + (xy 137.879172 97.040602) (xy 137.733501 96.980264) (xy 137.733489 96.980261) (xy 137.578845 96.9495) + (xy 137.578842 96.9495) (xy 137.421158 96.9495) (xy 137.421155 96.9495) (xy 137.26651 96.980261) + (xy 137.266498 96.980264) (xy 137.120827 97.040602) (xy 137.120814 97.040609) (xy 136.989711 97.12821) + (xy 136.989707 97.128213) (xy 136.878213 97.239707) (xy 136.87821 97.239711) (xy 136.790609 97.370814) + (xy 136.790602 97.370827) (xy 136.730264 97.516498) (xy 136.730261 97.51651) (xy 136.6995 97.671153) + (xy 135.931348 97.671153) (xy 135.959394 97.629179) (xy 136.019737 97.483497) (xy 136.0505 97.328842) + (xy 136.0505 97.171158) (xy 136.0505 97.171155) (xy 136.050499 97.171153) (xy 136.032204 97.079179) + (xy 136.019737 97.016503) (xy 136.019735 97.016498) (xy 135.959397 96.870827) (xy 135.95939 96.870814) + (xy 135.871789 96.739711) (xy 135.871786 96.739707) (xy 135.760292 96.628213) (xy 135.760284 96.628207) + (xy 135.722712 96.603102) (xy 135.677906 96.54949) (xy 135.669199 96.480165) (xy 135.699353 96.417138) + (xy 135.722712 96.396898) (xy 135.749279 96.379145) (xy 135.760289 96.371789) (xy 135.871789 96.260289) + (xy 135.959394 96.129179) (xy 136.019737 95.983497) (xy 136.0505 95.828842) (xy 136.0505 95.671158) + (xy 136.0505 95.671155) (xy 136.050499 95.671153) (xy 136.03533 95.594893) (xy 136.019737 95.516503) + (xy 136.006062 95.483489) (xy 135.959397 95.370827) (xy 135.95939 95.370814) (xy 135.871789 95.239711) + (xy 135.871786 95.239707) (xy 135.760292 95.128213) (xy 135.760288 95.12821) (xy 135.629185 95.040609) + (xy 135.629172 95.040602) (xy 135.483501 94.980264) (xy 135.483489 94.980261) (xy 135.328845 94.9495) + (xy 135.328842 94.9495) (xy 135.171158 94.9495) (xy 135.171155 94.9495) (xy 135.01651 94.980261) + (xy 135.016498 94.980264) (xy 134.870827 95.040602) (xy 134.870814 95.040609) (xy 134.739711 95.12821) + (xy 134.739707 95.128213) (xy 134.628213 95.239707) (xy 134.62821 95.239711) (xy 134.540609 95.370814) + (xy 134.540602 95.370827) (xy 134.480264 95.516498) (xy 134.480261 95.51651) (xy 134.4495 95.671153) + (xy 132.712719 95.671153) (xy 132.734895 95.617614) (xy 132.734895 95.617613) (xy 132.769737 95.533497) + (xy 132.8005 95.378842) (xy 132.8005 95.221158) (xy 132.8005 95.221155) (xy 132.800499 95.221153) + (xy 132.782012 95.128213) (xy 132.769737 95.066503) (xy 132.769735 95.066498) (xy 132.709397 94.920827) + (xy 132.70939 94.920814) (xy 132.651354 94.833957) (xy 132.621789 94.789711) (xy 132.621786 94.789707) + (xy 132.603232 94.771153) (xy 138.6995 94.771153) (xy 138.6995 94.928846) (xy 138.730261 95.083489) + (xy 138.730264 95.083501) (xy 138.790602 95.229172) (xy 138.790609 95.229185) (xy 138.87821 95.360288) + (xy 138.878213 95.360292) (xy 138.989707 95.471786) (xy 138.989711 95.471789) (xy 139.120814 95.55939) + (xy 139.120827 95.559397) (xy 139.266498 95.619735) (xy 139.266503 95.619737) (xy 139.421153 95.650499) + (xy 139.421156 95.6505) (xy 139.421158 95.6505) (xy 139.578844 95.6505) (xy 139.578845 95.650499) + (xy 139.733497 95.619737) (xy 139.877098 95.560256) (xy 139.879172 95.559397) (xy 139.879172 95.559396) + (xy 139.879179 95.559394) (xy 140.010289 95.471789) (xy 140.121789 95.360289) (xy 140.209394 95.229179) + (xy 140.210416 95.226713) (xy 140.269735 95.083501) (xy 140.269737 95.083497) (xy 140.3005 94.928842) + (xy 140.3005 94.771158) (xy 140.3005 94.771155) (xy 140.300499 94.771153) (xy 140.282012 94.678213) + (xy 140.269737 94.616503) (xy 140.269735 94.616498) (xy 140.209397 94.470827) (xy 140.20939 94.470814) + (xy 140.121789 94.339711) (xy 140.121786 94.339707) (xy 140.010292 94.228213) (xy 140.010288 94.22821) + (xy 139.879185 94.140609) (xy 139.879172 94.140602) (xy 139.733501 94.080264) (xy 139.733489 94.080261) + (xy 139.578845 94.0495) (xy 139.578842 94.0495) (xy 139.421158 94.0495) (xy 139.421155 94.0495) + (xy 139.26651 94.080261) (xy 139.266498 94.080264) (xy 139.120827 94.140602) (xy 139.120814 94.140609) + (xy 138.989711 94.22821) (xy 138.989707 94.228213) (xy 138.878213 94.339707) (xy 138.87821 94.339711) + (xy 138.790609 94.470814) (xy 138.790602 94.470827) (xy 138.730264 94.616498) (xy 138.730261 94.61651) + (xy 138.6995 94.771153) (xy 132.603232 94.771153) (xy 132.510292 94.678213) (xy 132.510288 94.67821) + (xy 132.379185 94.590609) (xy 132.379172 94.590602) (xy 132.233501 94.530264) (xy 132.233489 94.530261) + (xy 132.078845 94.4995) (xy 132.078842 94.4995) (xy 131.921158 94.4995) (xy 131.921155 94.4995) + (xy 131.76651 94.530261) (xy 131.766498 94.530264) (xy 131.620827 94.590602) (xy 131.620814 94.590609) + (xy 131.489711 94.67821) (xy 131.489707 94.678213) (xy 131.378213 94.789707) (xy 131.37821 94.789711) + (xy 131.290609 94.920814) (xy 131.290602 94.920827) (xy 131.230264 95.066498) (xy 131.230261 95.06651) + (xy 131.1995 95.221153) (xy 129.161378 95.221153) (xy 129.152285 95.204501) (xy 129.150049 95.165982) + (xy 129.150299 95.163445) (xy 129.150299 95.005759) (xy 129.150298 95.005757) (xy 129.145227 94.980263) + (xy 129.119536 94.851107) (xy 129.094105 94.789711) (xy 129.059196 94.705431) (xy 129.059189 94.705418) + (xy 128.971588 94.574315) (xy 128.971585 94.574311) (xy 128.860091 94.462817) (xy 128.860087 94.462814) + (xy 128.728984 94.375213) (xy 128.728971 94.375206) (xy 128.5833 94.314868) (xy 128.583288 94.314865) + (xy 128.428644 94.284104) (xy 128.428641 94.284104) (xy 128.270957 94.284104) (xy 128.270954 94.284104) + (xy 128.116309 94.314865) (xy 128.116297 94.314868) (xy 127.970626 94.375206) (xy 127.970613 94.375213) + (xy 127.83951 94.462814) (xy 127.839506 94.462817) (xy 127.728012 94.574311) (xy 127.728009 94.574315) + (xy 127.640408 94.705418) (xy 127.640401 94.705431) (xy 127.580063 94.851102) (xy 127.58006 94.851114) + (xy 127.549299 95.005757) (xy 127.549299 95.16345) (xy 127.58006 95.318093) (xy 127.580063 95.318105) + (xy 127.640401 95.463776) (xy 127.640408 95.463789) (xy 127.728009 95.594892) (xy 127.728012 95.594896) + (xy 127.839506 95.70639) (xy 127.83951 95.706393) (xy 127.970616 95.793996) (xy 127.970618 95.793996) + (xy 127.97062 95.793998) (xy 128.045486 95.825008) (xy 128.09989 95.868848) (xy 128.119651 95.915375) + (xy 128.124498 95.939741) (xy 128.124498 95.939742) (xy 128.173533 96.058124) (xy 128.173538 96.058133) + (xy 128.244723 96.164668) (xy 128.248589 96.169379) (xy 128.246958 96.170716) (xy 128.275858 96.223642) + (xy 128.270874 96.293334) (xy 128.247489 96.329719) (xy 128.248589 96.330621) (xy 128.244723 96.335331) + (xy 128.173538 96.441866) (xy 128.173533 96.441875) (xy 128.124499 96.560255) (xy 128.124497 96.560261) + (xy 128.0995 96.685928) (xy 128.0995 96.814071) (xy 128.100097 96.820134) (xy 128.097477 96.820391) + (xy 128.092238 96.878628) (xy 128.049349 96.933785) (xy 128.024323 96.947734) (xy 127.920823 96.990604) + (xy 127.920814 96.990609) (xy 127.789711 97.07821) (xy 127.789707 97.078213) (xy 127.678213 97.189707) + (xy 127.67821 97.189711) (xy 127.590609 97.320814) (xy 127.590602 97.320827) (xy 127.530264 97.466498) + (xy 127.530261 97.46651) (xy 127.4995 97.621153) (xy 127.4995 97.778846) (xy 127.528125 97.922749) + (xy 127.530263 97.933497) (xy 127.549687 97.980392) (xy 127.569427 98.028047) (xy 127.576896 98.097517) + (xy 127.545621 98.159996) (xy 127.485532 98.195648) (xy 127.454866 98.1995) (xy 127.421155 98.1995) + (xy 127.26651 98.230261) (xy 127.266498 98.230264) (xy 127.120827 98.290602) (xy 127.120814 98.290609) + (xy 126.989711 98.37821) (xy 126.989707 98.378213) (xy 126.878213 98.489707) (xy 126.87821 98.489711) + (xy 126.790609 98.620814) (xy 126.790602 98.620827) (xy 126.730264 98.766498) (xy 126.730261 98.76651) + (xy 126.6995 98.921153) (xy 126.6995 99.078846) (xy 126.730261 99.233489) (xy 126.730264 99.233501) + (xy 126.790602 99.379172) (xy 126.790609 99.379185) (xy 126.811198 99.409998) (xy 126.832076 99.476676) + (xy 126.813592 99.544056) (xy 126.761613 99.590746) (xy 126.692643 99.601922) (xy 126.683909 99.600507) + (xy 126.678846 99.5995) (xy 126.678842 99.5995) (xy 126.521158 99.5995) (xy 126.521155 99.5995) + (xy 126.36651 99.630261) (xy 126.366498 99.630264) (xy 126.220827 99.690602) (xy 126.220814 99.690609) + (xy 126.089711 99.77821) (xy 126.089707 99.778213) (xy 125.978213 99.889707) (xy 125.97821 99.889711) + (xy 125.890609 100.020814) (xy 125.890602 100.020827) (xy 125.830264 100.166498) (xy 125.830261 100.16651) + (xy 125.7995 100.321153) (xy 120.2505 100.321153) (xy 120.2505 96.621153) (xy 120.9995 96.621153) + (xy 120.9995 96.778846) (xy 121.030261 96.933489) (xy 121.030264 96.933501) (xy 121.090602 97.079172) + (xy 121.090609 97.079185) (xy 121.17821 97.210288) (xy 121.178213 97.210292) (xy 121.289707 97.321786) + (xy 121.289711 97.321789) (xy 121.420814 97.40939) (xy 121.420827 97.409397) (xy 121.558683 97.466498) + (xy 121.566503 97.469737) (xy 121.721153 97.500499) (xy 121.721156 97.5005) (xy 121.721158 97.5005) + (xy 121.878844 97.5005) (xy 121.878845 97.500499) (xy 122.033497 97.469737) (xy 122.179179 97.409394) + (xy 122.206329 97.391253) (xy 125.3495 97.391253) (xy 125.3495 97.548946) (xy 125.380261 97.703589) + (xy 125.380264 97.703601) (xy 125.440602 97.849272) (xy 125.440609 97.849285) (xy 125.52821 97.980388) + (xy 125.528213 97.980392) (xy 125.639707 98.091886) (xy 125.639711 98.091889) (xy 125.770814 98.17949) + (xy 125.770827 98.179497) (xy 125.916498 98.239835) (xy 125.916503 98.239837) (xy 126.019337 98.260292) + (xy 126.071153 98.270599) (xy 126.071156 98.2706) (xy 126.071158 98.2706) (xy 126.228844 98.2706) + (xy 126.228845 98.270599) (xy 126.383497 98.239837) (xy 126.529179 98.179494) (xy 126.660289 98.091889) + (xy 126.771789 97.980389) (xy 126.859394 97.849279) (xy 126.860771 97.845956) (xy 126.873067 97.816266) + (xy 126.919737 97.703597) (xy 126.9505 97.548942) (xy 126.9505 97.391258) (xy 126.9505 97.391255) + (xy 126.950499 97.391253) (xy 126.946433 97.370814) (xy 126.919737 97.236603) (xy 126.908839 97.210292) + (xy 126.859397 97.090927) (xy 126.85939 97.090914) (xy 126.771789 96.959811) (xy 126.771786 96.959807) + (xy 126.660292 96.848313) (xy 126.660288 96.84831) (xy 126.529185 96.760709) (xy 126.529172 96.760702) + (xy 126.383501 96.700364) (xy 126.383489 96.700361) (xy 126.228845 96.6696) (xy 126.228842 96.6696) + (xy 126.071158 96.6696) (xy 126.071155 96.6696) (xy 125.91651 96.700361) (xy 125.916498 96.700364) + (xy 125.770827 96.760702) (xy 125.770814 96.760709) (xy 125.639711 96.84831) (xy 125.639707 96.848313) + (xy 125.528213 96.959807) (xy 125.52821 96.959811) (xy 125.440609 97.090914) (xy 125.440602 97.090927) + (xy 125.380264 97.236598) (xy 125.380261 97.23661) (xy 125.3495 97.391253) (xy 122.206329 97.391253) + (xy 122.310289 97.321789) (xy 122.319264 97.312814) (xy 122.334594 97.297485) (xy 122.421786 97.210292) + (xy 122.421789 97.210289) (xy 122.509394 97.079179) (xy 122.518112 97.058133) (xy 122.535357 97.016498) + (xy 122.569737 96.933497) (xy 122.6005 96.778842) (xy 122.6005 96.621158) (xy 122.6005 96.621155) + (xy 122.600499 96.621153) (xy 122.596908 96.603102) (xy 122.569737 96.466503) (xy 122.559532 96.441866) + (xy 122.509397 96.320827) (xy 122.50939 96.320814) (xy 122.421789 96.189711) (xy 122.421786 96.189707) + (xy 122.310292 96.078213) (xy 122.310288 96.07821) (xy 122.179185 95.990609) (xy 122.179172 95.990602) + (xy 122.033501 95.930264) (xy 122.033489 95.930261) (xy 121.878845 95.8995) (xy 121.878842 95.8995) + (xy 121.721158 95.8995) (xy 121.721155 95.8995) (xy 121.56651 95.930261) (xy 121.566498 95.930264) + (xy 121.420827 95.990602) (xy 121.420814 95.990609) (xy 121.289711 96.07821) (xy 121.289707 96.078213) + (xy 121.178213 96.189707) (xy 121.17821 96.189711) (xy 121.090609 96.320814) (xy 121.090602 96.320827) + (xy 121.030264 96.466498) (xy 121.030261 96.46651) (xy 120.9995 96.621153) (xy 120.2505 96.621153) + (xy 120.2505 95.171153) (xy 122.9495 95.171153) (xy 122.9495 95.328846) (xy 122.980261 95.483489) + (xy 122.980264 95.483501) (xy 123.040602 95.629172) (xy 123.040609 95.629185) (xy 123.12821 95.760288) + (xy 123.128213 95.760292) (xy 123.239707 95.871786) (xy 123.239711 95.871789) (xy 123.370814 95.95939) + (xy 123.370827 95.959397) (xy 123.508683 96.016498) (xy 123.516503 96.019737) (xy 123.671153 96.050499) + (xy 123.671156 96.0505) (xy 123.8255 96.0505) (xy 123.892539 96.070185) (xy 123.938294 96.122989) + (xy 123.9495 96.1745) (xy 123.9495 96.328846) (xy 123.980261 96.483489) (xy 123.980264 96.483501) + (xy 124.040602 96.629172) (xy 124.040609 96.629185) (xy 124.12821 96.760288) (xy 124.128213 96.760292) + (xy 124.239707 96.871786) (xy 124.239711 96.871789) (xy 124.370814 96.95939) (xy 124.370827 96.959397) + (xy 124.446181 96.990609) (xy 124.516503 97.019737) (xy 124.671153 97.050499) (xy 124.671156 97.0505) + (xy 124.671158 97.0505) (xy 124.828844 97.0505) (xy 124.828845 97.050499) (xy 124.983497 97.019737) + (xy 125.096166 96.973067) (xy 125.129172 96.959397) (xy 125.129172 96.959396) (xy 125.129179 96.959394) + (xy 125.260289 96.871789) (xy 125.371789 96.760289) (xy 125.459394 96.629179) (xy 125.462719 96.621153) + (xy 125.483569 96.570814) (xy 125.519737 96.483497) (xy 125.5505 96.328842) (xy 125.5505 96.171158) + (xy 125.5505 96.171155) (xy 125.550499 96.171153) (xy 125.542148 96.129172) (xy 125.519737 96.016503) + (xy 125.516791 96.00939) (xy 125.459397 95.870827) (xy 125.45939 95.870814) (xy 125.371789 95.739711) + (xy 125.371786 95.739707) (xy 125.260292 95.628213) (xy 125.260288 95.62821) (xy 125.129185 95.540609) + (xy 125.129172 95.540602) (xy 124.983501 95.480264) (xy 124.983489 95.480261) (xy 124.828845 95.4495) + (xy 124.828842 95.4495) (xy 124.6745 95.4495) (xy 124.607461 95.429815) (xy 124.561706 95.377011) + (xy 124.5505 95.3255) (xy 124.5505 95.171155) (xy 124.550499 95.171153) (xy 124.529684 95.06651) + (xy 124.519737 95.016503) (xy 124.515286 95.005757) (xy 124.459397 94.870827) (xy 124.45939 94.870814) + (xy 124.371789 94.739711) (xy 124.371786 94.739707) (xy 124.260292 94.628213) (xy 124.260288 94.62821) + (xy 124.129185 94.540609) (xy 124.129172 94.540602) (xy 123.983501 94.480264) (xy 123.983489 94.480261) + (xy 123.828845 94.4495) (xy 123.828842 94.4495) (xy 123.671158 94.4495) (xy 123.671155 94.4495) + (xy 123.51651 94.480261) (xy 123.516498 94.480264) (xy 123.370827 94.540602) (xy 123.370814 94.540609) + (xy 123.239711 94.62821) (xy 123.239707 94.628213) (xy 123.128213 94.739707) (xy 123.12821 94.739711) + (xy 123.040609 94.870814) (xy 123.040602 94.870827) (xy 122.980264 95.016498) (xy 122.980261 95.01651) + (xy 122.9495 95.171153) (xy 120.2505 95.171153) (xy 120.2505 93.271153) (xy 128.8995 93.271153) + (xy 128.8995 93.428846) (xy 128.930261 93.583489) (xy 128.930264 93.583501) (xy 128.990602 93.729172) + (xy 128.990609 93.729185) (xy 129.07821 93.860288) (xy 129.078213 93.860292) (xy 129.189707 93.971786) + (xy 129.189711 93.971789) (xy 129.320814 94.05939) (xy 129.320827 94.059397) (xy 129.466498 94.119735) + (xy 129.466503 94.119737) (xy 129.621153 94.150499) (xy 129.621156 94.1505) (xy 129.621158 94.1505) + (xy 129.778844 94.1505) (xy 129.778845 94.150499) (xy 129.933497 94.119737) (xy 130.079179 94.059394) + (xy 130.210289 93.971789) (xy 130.321789 93.860289) (xy 130.409394 93.729179) (xy 130.469737 93.583497) + (xy 130.5005 93.428842) (xy 130.5005 93.341804) (xy 130.520185 93.274765) (xy 130.555606 93.238704) + (xy 130.580923 93.221789) (xy 130.692423 93.110289) (xy 130.780028 92.979179) (xy 130.783488 92.970827) + (xy 130.837797 92.839711) (xy 130.840371 92.833497) (xy 130.871134 92.678842) (xy 130.871134 92.521158) + (xy 130.871134 92.521155) (xy 130.871133 92.521153) (xy 130.840372 92.36651) (xy 130.840371 92.366503) + (xy 130.840369 92.366498) (xy 130.780031 92.220827) (xy 130.780024 92.220814) (xy 130.692423 92.089711) + (xy 130.69242 92.089707) (xy 130.580926 91.978213) (xy 130.580922 91.97821) (xy 130.449819 91.890609) + (xy 130.449806 91.890602) (xy 130.304135 91.830264) (xy 130.304123 91.830261) (xy 130.149479 91.7995) + (xy 130.149476 91.7995) (xy 129.991792 91.7995) (xy 129.991789 91.7995) (xy 129.837144 91.830261) + (xy 129.837132 91.830264) (xy 129.691461 91.890602) (xy 129.691448 91.890609) (xy 129.560345 91.97821) + (xy 129.560341 91.978213) (xy 129.448847 92.089707) (xy 129.448844 92.089711) (xy 129.361243 92.220814) + (xy 129.361236 92.220827) (xy 129.300898 92.366498) (xy 129.300895 92.36651) (xy 129.270134 92.521153) + (xy 129.270134 92.608194) (xy 129.250449 92.675233) (xy 129.215026 92.711296) (xy 129.189707 92.728213) + (xy 129.078213 92.839707) (xy 129.07821 92.839711) (xy 128.990609 92.970814) (xy 128.990602 92.970827) + (xy 128.930264 93.116498) (xy 128.930261 93.11651) (xy 128.8995 93.271153) (xy 120.2505 93.271153) + (xy 120.2505 90.621153) (xy 140.1495 90.621153) (xy 140.1495 90.778846) (xy 140.180261 90.933489) + (xy 140.180264 90.933501) (xy 140.240602 91.079172) (xy 140.240609 91.079185) (xy 140.32821 91.210288) + (xy 140.328213 91.210292) (xy 140.439707 91.321786) (xy 140.439711 91.321789) (xy 140.570814 91.40939) + (xy 140.570827 91.409397) (xy 140.67006 91.4505) (xy 140.716503 91.469737) (xy 140.871153 91.500499) + (xy 140.871156 91.5005) (xy 140.871158 91.5005) (xy 141.028844 91.5005) (xy 141.028845 91.500499) + (xy 141.183497 91.469737) (xy 141.329179 91.409394) (xy 141.460289 91.321789) (xy 141.571789 91.210289) + (xy 141.659394 91.079179) (xy 141.719737 90.933497) (xy 141.7505 90.778842) (xy 141.7505 90.621158) + (xy 141.7505 90.621155) (xy 141.744155 90.589258) (xy 141.744155 90.589257) (xy 141.740554 90.571153) + (xy 143.9995 90.571153) (xy 143.9995 90.728846) (xy 144.030261 90.883489) (xy 144.030264 90.883501) + (xy 144.090602 91.029172) (xy 144.090609 91.029185) (xy 144.17821 91.160288) (xy 144.178213 91.160292) + (xy 144.289707 91.271786) (xy 144.289711 91.271789) (xy 144.420814 91.35939) (xy 144.420827 91.359397) + (xy 144.566498 91.419735) (xy 144.566503 91.419737) (xy 144.721153 91.450499) (xy 144.721156 91.4505) + (xy 144.721158 91.4505) (xy 144.878844 91.4505) (xy 144.878845 91.450499) (xy 145.033497 91.419737) + (xy 145.179179 91.359394) (xy 145.310289 91.271789) (xy 145.421789 91.160289) (xy 145.509394 91.029179) + (xy 145.569737 90.883497) (xy 145.6005 90.728842) (xy 145.6005 90.571158) (xy 145.6005 90.571155) + (xy 145.600499 90.571153) (xy 145.579684 90.46651) (xy 145.569737 90.416503) (xy 145.530102 90.320814) + (xy 145.509397 90.270827) (xy 145.50939 90.270814) (xy 145.421789 90.139711) (xy 145.421786 90.139707) + (xy 145.310292 90.028213) (xy 145.310288 90.02821) (xy 145.179185 89.940609) (xy 145.179172 89.940602) + (xy 145.033501 89.880264) (xy 145.033489 89.880261) (xy 144.878845 89.8495) (xy 144.878842 89.8495) + (xy 144.721158 89.8495) (xy 144.721155 89.8495) (xy 144.56651 89.880261) (xy 144.566498 89.880264) + (xy 144.420827 89.940602) (xy 144.420814 89.940609) (xy 144.289711 90.02821) (xy 144.289707 90.028213) + (xy 144.178213 90.139707) (xy 144.17821 90.139711) (xy 144.090609 90.270814) (xy 144.090602 90.270827) + (xy 144.030264 90.416498) (xy 144.030261 90.41651) (xy 143.9995 90.571153) (xy 141.740554 90.571153) + (xy 141.719738 90.46651) (xy 141.719737 90.466503) (xy 141.719735 90.466498) (xy 141.659397 90.320827) + (xy 141.65939 90.320814) (xy 141.571789 90.189711) (xy 141.571786 90.189707) (xy 141.460292 90.078213) + (xy 141.460288 90.07821) (xy 141.329185 89.990609) (xy 141.329172 89.990602) (xy 141.183501 89.930264) + (xy 141.183489 89.930261) (xy 141.028845 89.8995) (xy 141.028842 89.8995) (xy 140.871158 89.8995) + (xy 140.871155 89.8995) (xy 140.71651 89.930261) (xy 140.716498 89.930264) (xy 140.570827 89.990602) + (xy 140.570814 89.990609) (xy 140.439711 90.07821) (xy 140.439707 90.078213) (xy 140.328213 90.189707) + (xy 140.32821 90.189711) (xy 140.240609 90.320814) (xy 140.240602 90.320827) (xy 140.180264 90.466498) + (xy 140.180261 90.46651) (xy 140.1495 90.621153) (xy 120.2505 90.621153) (xy 120.2505 88.62207) + (xy 130.1245 88.62207) (xy 130.1245 88.877929) (xy 130.164526 89.13064) (xy 130.243588 89.373972) + (xy 130.243589 89.373975) (xy 130.35975 89.60195) (xy 130.510132 89.808935) (xy 130.510136 89.80894) + (xy 130.691059 89.989863) (xy 130.691064 89.989867) (xy 130.812663 90.078213) (xy 130.898053 90.140252) + (xy 131.04708 90.216185) (xy 131.126024 90.25641) (xy 131.126027 90.256411) (xy 131.170396 90.270827) + (xy 131.369361 90.335474) (xy 131.62207 90.3755) (xy 131.622071 90.3755) (xy 131.877929 90.3755) + (xy 131.87793 90.3755) (xy 132.130639 90.335474) (xy 132.373975 90.25641) (xy 132.601947 90.140252) + (xy 132.808942 89.989862) (xy 132.989862 89.808942) (xy 133.140252 89.601947) (xy 133.25641 89.373975) + (xy 133.335474 89.130639) (xy 133.3755 88.87793) (xy 133.3755 88.62207) (xy 136.6245 88.62207) (xy 136.6245 88.877929) + (xy 136.664526 89.13064) (xy 136.743588 89.373972) (xy 136.743589 89.373975) (xy 136.85975 89.60195) + (xy 137.010132 89.808935) (xy 137.010136 89.80894) (xy 137.191059 89.989863) (xy 137.191064 89.989867) + (xy 137.312663 90.078213) (xy 137.398053 90.140252) (xy 137.54708 90.216185) (xy 137.626024 90.25641) + (xy 137.626027 90.256411) (xy 137.670396 90.270827) (xy 137.869361 90.335474) (xy 138.12207 90.3755) + (xy 138.122071 90.3755) (xy 138.377929 90.3755) (xy 138.37793 90.3755) (xy 138.630639 90.335474) + (xy 138.873975 90.25641) (xy 139.101947 90.140252) (xy 139.308942 89.989862) (xy 139.489862 89.808942) + (xy 139.640252 89.601947) (xy 139.75641 89.373975) (xy 139.835474 89.130639) (xy 139.8755 88.87793) + (xy 139.8755 88.62207) (xy 139.835474 88.369361) (xy 139.773681 88.179179) (xy 139.756411 88.126027) + (xy 139.756405 88.126014) (xy 139.728559 88.071363) (xy 139.728557 88.071361) (xy 139.702977 88.021158) + (xy 139.702974 88.021153) (xy 144.5995 88.021153) (xy 144.5995 88.178846) (xy 144.630261 88.333489) + (xy 144.630264 88.333501) (xy 144.690602 88.479172) (xy 144.690609 88.479185) (xy 144.77821 88.610288) + (xy 144.778213 88.610292) (xy 144.889707 88.721786) (xy 144.889711 88.721789) (xy 145.020814 88.80939) + (xy 145.020827 88.809397) (xy 145.166498 88.869735) (xy 145.166503 88.869737) (xy 145.321153 88.900499) + (xy 145.321156 88.9005) (xy 145.321158 88.9005) (xy 145.478844 88.9005) (xy 145.478845 88.900499) + (xy 145.633497 88.869737) (xy 145.779179 88.809394) (xy 145.910289 88.721789) (xy 146.021789 88.610289) + (xy 146.109394 88.479179) (xy 146.169737 88.333497) (xy 146.2005 88.178842) (xy 146.2005 88.021158) + (xy 146.2005 88.021155) (xy 146.200499 88.021153) (xy 146.169737 87.866503) (xy 146.109534 87.721158) + (xy 146.109397 87.720827) (xy 146.10939 87.720814) (xy 146.021789 87.589711) (xy 146.021786 87.589707) + (xy 145.910292 87.478213) (xy 145.910288 87.47821) (xy 145.779185 87.390609) (xy 145.779172 87.390602) + (xy 145.633501 87.330264) (xy 145.633489 87.330261) (xy 145.478845 87.2995) (xy 145.478842 87.2995) + (xy 145.321158 87.2995) (xy 145.321155 87.2995) (xy 145.16651 87.330261) (xy 145.166498 87.330264) + (xy 145.020827 87.390602) (xy 145.020814 87.390609) (xy 144.889711 87.47821) (xy 144.889707 87.478213) + (xy 144.778213 87.589707) (xy 144.77821 87.589711) (xy 144.690609 87.720814) (xy 144.690602 87.720827) + (xy 144.630264 87.866498) (xy 144.630261 87.86651) (xy 144.5995 88.021153) (xy 139.702974 88.021153) + (xy 139.640252 87.898053) (xy 139.511729 87.721155) (xy 139.489867 87.691064) (xy 139.489863 87.691059) + (xy 139.30894 87.510136) (xy 139.308935 87.510132) (xy 139.10195 87.35975) (xy 139.101949 87.359749) + (xy 139.101947 87.359748) (xy 139.02891 87.322533) (xy 138.873975 87.243589) (xy 138.873972 87.243588) + (xy 138.63064 87.164526) (xy 138.504284 87.144513) (xy 138.37793 87.1245) (xy 138.12207 87.1245) + (xy 138.037833 87.137842) (xy 137.869359 87.164526) (xy 137.626027 87.243588) (xy 137.626024 87.243589) + (xy 137.398049 87.35975) (xy 137.191064 87.510132) (xy 137.191059 87.510136) (xy 137.010136 87.691059) + (xy 137.010132 87.691064) (xy 136.85975 87.898049) (xy 136.743589 88.126024) (xy 136.743588 88.126027) + (xy 136.664526 88.369359) (xy 136.6245 88.62207) (xy 133.3755 88.62207) (xy 133.335474 88.369361) + (xy 133.273681 88.179179) (xy 133.256411 88.126027) (xy 133.25641 88.126024) (xy 133.202975 88.021153) + (xy 133.140252 87.898053) (xy 133.011729 87.721155) (xy 132.989867 87.691064) (xy 132.989863 87.691059) + (xy 132.80894 87.510136) (xy 132.808935 87.510132) (xy 132.60195 87.35975) (xy 132.601949 87.359749) + (xy 132.601947 87.359748) (xy 132.52891 87.322533) (xy 132.373975 87.243589) (xy 132.373972 87.243588) + (xy 132.13064 87.164526) (xy 132.004284 87.144513) (xy 131.87793 87.1245) (xy 131.62207 87.1245) + (xy 131.537833 87.137842) (xy 131.369359 87.164526) (xy 131.126027 87.243588) (xy 131.126024 87.243589) + (xy 130.898049 87.35975) (xy 130.691064 87.510132) (xy 130.691059 87.510136) (xy 130.510136 87.691059) + (xy 130.510132 87.691064) (xy 130.35975 87.898049) (xy 130.243589 88.126024) (xy 130.243588 88.126027) + (xy 130.164526 88.369359) (xy 130.1245 88.62207) (xy 120.2505 88.62207) (xy 120.2505 87.721153) + (xy 121.4995 87.721153) (xy 121.4995 87.878846) (xy 121.530261 88.033489) (xy 121.530264 88.033501) + (xy 121.590602 88.179172) (xy 121.590609 88.179185) (xy 121.67821 88.310288) (xy 121.678213 88.310292) + (xy 121.789707 88.421786) (xy 121.789711 88.421789) (xy 121.920814 88.50939) (xy 121.920827 88.509397) + (xy 122.066498 88.569735) (xy 122.066503 88.569737) (xy 122.221153 88.600499) (xy 122.221156 88.6005) + (xy 122.221158 88.6005) (xy 122.378844 88.6005) (xy 122.378845 88.600499) (xy 122.533497 88.569737) + (xy 122.679179 88.509394) (xy 122.810289 88.421789) (xy 122.921789 88.310289) (xy 123.009394 88.179179) + (xy 123.069737 88.033497) (xy 123.1005 87.878842) (xy 123.1005 87.721158) (xy 123.1005 87.721155) + (xy 123.100499 87.721153) (xy 123.074353 87.589711) (xy 123.069737 87.566503) (xy 123.046388 87.510132) + (xy 123.009397 87.420827) (xy 123.00939 87.420814) (xy 122.921789 87.289711) (xy 122.921786 87.289707) + (xy 122.810292 87.178213) (xy 122.810288 87.17821) (xy 122.679185 87.090609) (xy 122.679172 87.090602) + (xy 122.533501 87.030264) (xy 122.533489 87.030261) (xy 122.378845 86.9995) (xy 122.378842 86.9995) + (xy 122.221158 86.9995) (xy 122.221155 86.9995) (xy 122.06651 87.030261) (xy 122.066498 87.030264) + (xy 121.920827 87.090602) (xy 121.920814 87.090609) (xy 121.789711 87.17821) (xy 121.789707 87.178213) + (xy 121.678213 87.289707) (xy 121.67821 87.289711) (xy 121.590609 87.420814) (xy 121.590602 87.420827) + (xy 121.530264 87.566498) (xy 121.530261 87.56651) (xy 121.4995 87.721153) (xy 120.2505 87.721153) + (xy 120.2505 85.693995) (xy 121.099499 85.693995) (xy 121.126418 85.829322) (xy 121.126421 85.829332) + (xy 121.179221 85.956804) (xy 121.179228 85.956817) (xy 121.255885 86.071541) (xy 121.255888 86.071545) + (xy 121.353454 86.169111) (xy 121.353458 86.169114) (xy 121.468182 86.245771) (xy 121.468195 86.245778) + (xy 121.595667 86.298578) (xy 121.595672 86.29858) (xy 121.595676 86.29858) (xy 121.595677 86.298581) + (xy 121.731004 86.3255) (xy 121.731007 86.3255) (xy 121.868995 86.3255) (xy 121.960041 86.307389) + (xy 122.004328 86.29858) (xy 122.131811 86.245775) (xy 122.16866 86.221153) (xy 143.7995 86.221153) + (xy 143.7995 86.378846) (xy 143.830261 86.533489) (xy 143.830264 86.533501) (xy 143.890602 86.679172) + (xy 143.890609 86.679185) (xy 143.97821 86.810288) (xy 143.978213 86.810292) (xy 144.089707 86.921786) + (xy 144.089711 86.921789) (xy 144.220814 87.00939) (xy 144.220827 87.009397) (xy 144.366498 87.069735) + (xy 144.366503 87.069737) (xy 144.521153 87.100499) (xy 144.521156 87.1005) (xy 144.521158 87.1005) + (xy 144.678844 87.1005) (xy 144.678845 87.100499) (xy 144.833497 87.069737) (xy 144.979179 87.009394) + (xy 145.110289 86.921789) (xy 145.221789 86.810289) (xy 145.309394 86.679179) (xy 145.369737 86.533497) + (xy 145.4005 86.378842) (xy 145.4005 86.221158) (xy 145.4005 86.221155) (xy 145.400499 86.221153) + (xy 145.369738 86.06651) (xy 145.369737 86.066503) (xy 145.324304 85.956817) (xy 145.309397 85.920827) + (xy 145.30939 85.920814) (xy 145.221789 85.789711) (xy 145.221786 85.789707) (xy 145.126074 85.693995) + (xy 147.499499 85.693995) (xy 147.526418 85.829322) (xy 147.526421 85.829332) (xy 147.579221 85.956804) + (xy 147.579228 85.956817) (xy 147.655885 86.071541) (xy 147.655888 86.071545) (xy 147.753454 86.169111) + (xy 147.753458 86.169114) (xy 147.868182 86.245771) (xy 147.868195 86.245778) (xy 147.995667 86.298578) + (xy 147.995672 86.29858) (xy 147.995676 86.29858) (xy 147.995677 86.298581) (xy 148.131004 86.3255) + (xy 148.131007 86.3255) (xy 148.268995 86.3255) (xy 148.360041 86.307389) (xy 148.404328 86.29858) + (xy 148.531811 86.245775) (xy 148.646542 86.169114) (xy 148.744114 86.071542) (xy 148.820775 85.956811) + (xy 148.87358 85.829328) (xy 148.888084 85.756411) (xy 148.9005 85.693995) (xy 148.9005 85.556004) + (xy 148.873581 85.420677) (xy 148.87358 85.420676) (xy 148.87358 85.420672) (xy 148.873578 85.420667) + (xy 148.820778 85.293195) (xy 148.820771 85.293182) (xy 148.744114 85.178458) (xy 148.744111 85.178454) + (xy 148.646545 85.080888) (xy 148.646541 85.080885) (xy 148.531817 85.004228) (xy 148.531804 85.004221) + (xy 148.404332 84.951421) (xy 148.404322 84.951418) (xy 148.268995 84.9245) (xy 148.268993 84.9245) + (xy 148.131007 84.9245) (xy 148.131005 84.9245) (xy 147.995677 84.951418) (xy 147.995667 84.951421) + (xy 147.868195 85.004221) (xy 147.868182 85.004228) (xy 147.753458 85.080885) (xy 147.753454 85.080888) + (xy 147.655888 85.178454) (xy 147.655885 85.178458) (xy 147.579228 85.293182) (xy 147.579221 85.293195) + (xy 147.526421 85.420667) (xy 147.526418 85.420677) (xy 147.4995 85.556004) (xy 147.4995 85.556007) + (xy 147.4995 85.693993) (xy 147.4995 85.693995) (xy 147.499499 85.693995) (xy 145.126074 85.693995) + (xy 145.110292 85.678213) (xy 145.110288 85.67821) (xy 145.072584 85.653017) (xy 144.979185 85.590609) + (xy 144.979172 85.590602) (xy 144.833501 85.530264) (xy 144.833489 85.530261) (xy 144.678845 85.4995) + (xy 144.678842 85.4995) (xy 144.521158 85.4995) (xy 144.521155 85.4995) (xy 144.36651 85.530261) + (xy 144.366498 85.530264) (xy 144.220827 85.590602) (xy 144.220814 85.590609) (xy 144.089711 85.67821) + (xy 144.089707 85.678213) (xy 143.978213 85.789707) (xy 143.97821 85.789711) (xy 143.890609 85.920814) + (xy 143.890602 85.920827) (xy 143.830264 86.066498) (xy 143.830261 86.06651) (xy 143.7995 86.221153) + (xy 122.16866 86.221153) (xy 122.246542 86.169114) (xy 122.246545 86.169111) (xy 122.288272 86.127385) + (xy 122.344111 86.071545) (xy 122.344114 86.071542) (xy 122.420775 85.956811) (xy 122.47358 85.829328) + (xy 122.488084 85.756411) (xy 122.5005 85.693995) (xy 122.5005 85.556004) (xy 122.473581 85.420677) + (xy 122.47358 85.420676) (xy 122.47358 85.420672) (xy 122.473578 85.420667) (xy 122.420778 85.293195) + (xy 122.420771 85.293182) (xy 122.344114 85.178458) (xy 122.344111 85.178454) (xy 122.246545 85.080888) + (xy 122.246541 85.080885) (xy 122.131817 85.004228) (xy 122.131804 85.004221) (xy 122.004332 84.951421) + (xy 122.004322 84.951418) (xy 121.868995 84.9245) (xy 121.868993 84.9245) (xy 121.731007 84.9245) + (xy 121.731005 84.9245) (xy 121.595677 84.951418) (xy 121.595667 84.951421) (xy 121.468195 85.004221) + (xy 121.468182 85.004228) (xy 121.353458 85.080885) (xy 121.353454 85.080888) (xy 121.255888 85.178454) + (xy 121.255885 85.178458) (xy 121.179228 85.293182) (xy 121.179221 85.293195) (xy 121.126421 85.420667) + (xy 121.126418 85.420677) (xy 121.0995 85.556004) (xy 121.0995 85.556007) (xy 121.0995 85.693993) + (xy 121.0995 85.693995) (xy 121.099499 85.693995) (xy 120.2505 85.693995) (xy 120.2505 83.621153) + (xy 123.2995 83.621153) (xy 123.2995 83.778846) (xy 123.330261 83.933489) (xy 123.330264 83.933501) + (xy 123.390602 84.079172) (xy 123.390609 84.079185) (xy 123.47821 84.210288) (xy 123.478213 84.210292) + (xy 123.589707 84.321786) (xy 123.589711 84.321789) (xy 123.720814 84.40939) (xy 123.720827 84.409397) + (xy 123.866498 84.469735) (xy 123.866503 84.469737) (xy 124.021153 84.500499) (xy 124.021156 84.5005) + (xy 124.021158 84.5005) (xy 124.178844 84.5005) (xy 124.178845 84.500499) (xy 124.333497 84.469737) + (xy 124.479179 84.409394) (xy 124.610289 84.321789) (xy 124.721789 84.210289) (xy 124.809394 84.079179) + (xy 124.812393 84.07194) (xy 124.869735 83.933501) (xy 124.869737 83.933497) (xy 124.9005 83.778842) + (xy 124.9005 83.621158) (xy 124.9005 83.621155) (xy 124.900499 83.621153) (xy 124.899547 83.616365) + (xy 124.869737 83.466503) (xy 124.835411 83.383634) (xy 126.8995 83.383634) (xy 126.8995 83.616365) + (xy 126.899501 83.616382) (xy 126.925029 83.810291) (xy 126.929879 83.847126) (xy 126.989527 84.069736) + (xy 126.99012 84.071947) (xy 127.07918 84.28696) (xy 127.079188 84.286976) (xy 127.195553 84.488524) + (xy 127.195564 84.48854) (xy 127.337242 84.673179) (xy 127.337248 84.673186) (xy 127.501813 84.837751) + (xy 127.50182 84.837757) (xy 127.614866 84.9245) (xy 127.686468 84.979442) (xy 127.686475 84.979446) + (xy 127.888023 85.095811) (xy 127.888039 85.095819) (xy 128.103052 85.184879) (xy 128.103054 85.184879) + (xy 128.10306 85.184882) (xy 128.327874 85.245121) (xy 128.558628 85.2755) (xy 128.558635 85.2755) + (xy 128.791365 85.2755) (xy 128.791372 85.2755) (xy 129.022126 85.245121) (xy 129.24694 85.184882) + (xy 129.447165 85.101947) (xy 129.46196 85.095819) (xy 129.461963 85.095817) (xy 129.461969 85.095815) + (xy 129.663532 84.979442) (xy 129.848181 84.837756) (xy 129.994657 84.691279) (xy 130.055978 84.657796) + (xy 130.12567 84.66278) (xy 130.181604 84.704651) (xy 130.200268 84.740644) (xy 130.243588 84.873972) + (xy 130.243589 84.873975) (xy 130.297328 84.979442) (xy 130.349016 85.080885) (xy 130.35975 85.10195) + (xy 130.510132 85.308935) (xy 130.510136 85.30894) (xy 130.691059 85.489863) (xy 130.691064 85.489867) + (xy 130.782095 85.556004) (xy 130.898053 85.640252) (xy 131.04708 85.716185) (xy 131.126024 85.75641) + (xy 131.126027 85.756411) (xy 131.228503 85.789707) (xy 131.369361 85.835474) (xy 131.62207 85.8755) + (xy 131.622071 85.8755) (xy 131.877929 85.8755) (xy 131.87793 85.8755) (xy 132.130639 85.835474) + (xy 132.373975 85.75641) (xy 132.601947 85.640252) (xy 132.808942 85.489862) (xy 132.989862 85.308942) + (xy 133.140252 85.101947) (xy 133.25641 84.873975) (xy 133.335474 84.630639) (xy 133.3755 84.37793) + (xy 133.3755 84.12207) (xy 136.6245 84.12207) (xy 136.6245 84.377929) (xy 136.664526 84.63064) (xy 136.743588 84.873972) + (xy 136.743589 84.873975) (xy 136.797328 84.979442) (xy 136.849016 85.080885) (xy 136.85975 85.10195) + (xy 137.010132 85.308935) (xy 137.010136 85.30894) (xy 137.191059 85.489863) (xy 137.191064 85.489867) + (xy 137.282095 85.556004) (xy 137.398053 85.640252) (xy 137.54708 85.716185) (xy 137.626024 85.75641) + (xy 137.626027 85.756411) (xy 137.728503 85.789707) (xy 137.869361 85.835474) (xy 138.12207 85.8755) + (xy 138.122071 85.8755) (xy 138.377929 85.8755) (xy 138.37793 85.8755) (xy 138.630639 85.835474) + (xy 138.873975 85.75641) (xy 139.101947 85.640252) (xy 139.308942 85.489862) (xy 139.489862 85.308942) + (xy 139.640252 85.101947) (xy 139.75641 84.873975) (xy 139.799731 84.740644) (xy 139.839168 84.682969) + (xy 139.903526 84.65577) (xy 139.972373 84.667684) (xy 140.005343 84.691281) (xy 140.151813 84.837751) + (xy 140.15182 84.837757) (xy 140.264866 84.9245) (xy 140.336468 84.979442) (xy 140.336475 84.979446) + (xy 140.538023 85.095811) (xy 140.538039 85.095819) (xy 140.753052 85.184879) (xy 140.753054 85.184879) + (xy 140.75306 85.184882) (xy 140.977874 85.245121) (xy 141.208628 85.2755) (xy 141.208635 85.2755) + (xy 141.441365 85.2755) (xy 141.441372 85.2755) (xy 141.672126 85.245121) (xy 141.89694 85.184882) + (xy 142.097165 85.101947) (xy 142.11196 85.095819) (xy 142.111963 85.095817) (xy 142.111969 85.095815) + (xy 142.313532 84.979442) (xy 142.498181 84.837756) (xy 142.662756 84.673181) (xy 142.804442 84.488532) + (xy 142.920815 84.286969) (xy 143.009882 84.07194) (xy 143.070121 83.847126) (xy 143.1005 83.616372) + (xy 143.1005 83.383628) (xy 143.07911 83.221152) (xy 145.448028 83.221152) (xy 145.448028 83.378845) + (xy 145.478789 83.533488) (xy 145.478792 83.5335) (xy 145.53913 83.679171) (xy 145.539137 83.679184) + (xy 145.626738 83.810287) (xy 145.626741 83.810291) (xy 145.738235 83.921785) (xy 145.738239 83.921788) + (xy 145.869342 84.009389) (xy 145.869355 84.009396) (xy 146.015026 84.069734) (xy 146.015031 84.069736) + (xy 146.169681 84.100498) (xy 146.169684 84.100499) (xy 146.169686 84.100499) (xy 146.327372 84.100499) + (xy 146.327373 84.100498) (xy 146.482025 84.069736) (xy 146.627707 84.009393) (xy 146.758817 83.921788) + (xy 146.870317 83.810288) (xy 146.957922 83.679178) (xy 147.018265 83.533496) (xy 147.049028 83.378841) + (xy 147.049028 83.221157) (xy 147.049028 83.221154) (xy 147.049027 83.221152) (xy 147.035446 83.152877) + (xy 147.018265 83.066502) (xy 147.009991 83.046527) (xy 146.957925 82.920826) (xy 146.957918 82.920813) + (xy 146.870317 82.78971) (xy 146.870314 82.789706) (xy 146.75882 82.678212) (xy 146.758816 82.678209) + (xy 146.627713 82.590608) (xy 146.6277 82.590601) (xy 146.482029 82.530263) (xy 146.482017 82.53026) + (xy 146.327373 82.499499) (xy 146.32737 82.499499) (xy 146.169686 82.499499) (xy 146.169683 82.499499) + (xy 146.015038 82.53026) (xy 146.015026 82.530263) (xy 145.869355 82.590601) (xy 145.869342 82.590608) + (xy 145.738239 82.678209) (xy 145.738235 82.678212) (xy 145.626741 82.789706) (xy 145.626738 82.78971) + (xy 145.539137 82.920813) (xy 145.53913 82.920826) (xy 145.478792 83.066497) (xy 145.478789 83.066509) + (xy 145.448028 83.221152) (xy 143.07911 83.221152) (xy 143.070121 83.152874) (xy 143.009882 82.92806) + (xy 143.009879 82.928052) (xy 142.920819 82.713039) (xy 142.920811 82.713023) (xy 142.804446 82.511475) + (xy 142.804442 82.511468) (xy 142.796662 82.501329) (xy 142.771467 82.436162) (xy 142.785504 82.367717) + (xy 142.834317 82.317726) (xy 142.902408 82.302061) (xy 142.951332 82.315357) (xy 143.144406 82.413734) + (xy 143.144408 82.413734) (xy 143.144411 82.413736) (xy 143.372778 82.487937) (xy 143.609941 82.5255) + (xy 143.609942 82.5255) (xy 143.850058 82.5255) (xy 143.850059 82.5255) (xy 144.087222 82.487937) + (xy 144.315589 82.413736) (xy 144.529536 82.304724) (xy 144.723796 82.163586) (xy 144.893586 81.993796) + (xy 145.034724 81.799536) (xy 145.143736 81.585589) (xy 145.189743 81.443995) (xy 147.499499 81.443995) + (xy 147.526418 81.579322) (xy 147.526421 81.579332) (xy 147.579221 81.706804) (xy 147.579228 81.706817) + (xy 147.655885 81.821541) (xy 147.655888 81.821545) (xy 147.753454 81.919111) (xy 147.753458 81.919114) + (xy 147.868182 81.995771) (xy 147.868195 81.995778) (xy 147.995667 82.048578) (xy 147.995672 82.04858) + (xy 147.995676 82.04858) (xy 147.995677 82.048581) (xy 148.131004 82.0755) (xy 148.131007 82.0755) + (xy 148.268995 82.0755) (xy 148.360041 82.057389) (xy 148.404328 82.04858) (xy 148.531811 81.995775) + (xy 148.646542 81.919114) (xy 148.744114 81.821542) (xy 148.820775 81.706811) (xy 148.87358 81.579328) + (xy 148.9005 81.443993) (xy 148.9005 81.306007) (xy 148.9005 81.306004) (xy 148.873581 81.170677) + (xy 148.87358 81.170676) (xy 148.87358 81.170672) (xy 148.873578 81.170667) (xy 148.820778 81.043195) + (xy 148.820771 81.043182) (xy 148.744114 80.928458) (xy 148.744111 80.928454) (xy 148.646545 80.830888) + (xy 148.646541 80.830885) (xy 148.531817 80.754228) (xy 148.531804 80.754221) (xy 148.404332 80.701421) + (xy 148.404322 80.701418) (xy 148.268995 80.6745) (xy 148.268993 80.6745) (xy 148.131007 80.6745) + (xy 148.131005 80.6745) (xy 147.995677 80.701418) (xy 147.995667 80.701421) (xy 147.868195 80.754221) + (xy 147.868182 80.754228) (xy 147.753458 80.830885) (xy 147.753454 80.830888) (xy 147.655888 80.928454) + (xy 147.655885 80.928458) (xy 147.579228 81.043182) (xy 147.579221 81.043195) (xy 147.526421 81.170667) + (xy 147.526418 81.170677) (xy 147.4995 81.306004) (xy 147.4995 81.306007) (xy 147.4995 81.443993) + (xy 147.4995 81.443995) (xy 147.499499 81.443995) (xy 145.189743 81.443995) (xy 145.217937 81.357222) + (xy 145.2555 81.120059) (xy 145.2555 80.879941) (xy 145.217937 80.642778) (xy 145.143736 80.414411) + (xy 145.143734 80.414408) (xy 145.143734 80.414406) (xy 145.034723 80.200463) (xy 144.893586 80.006204) + (xy 144.725063 79.837681) (xy 144.691578 79.776358) (xy 144.696562 79.706666) (xy 144.725063 79.662319) + (xy 144.893586 79.493796) (xy 145.034724 79.299536) (xy 145.143736 79.085589) (xy 145.217937 78.857222) + (xy 145.2555 78.620059) (xy 145.2555 78.379941) (xy 145.217937 78.142778) (xy 145.143736 77.914411) + (xy 145.143734 77.914408) (xy 145.143734 77.914406) (xy 145.034723 77.700463) (xy 144.893586 77.506204) + (xy 144.723796 77.336414) (xy 144.671824 77.298654) (xy 144.657859 77.280544) (xy 144.657426 77.280978) + (xy 143.879822 76.503375) (xy 143.932642 76.489222) (xy 144.052357 76.420104) (xy 144.150104 76.322357) + (xy 144.219222 76.202642) (xy 144.233375 76.149822) (xy 144.970556 76.887004) (xy 144.970556 76.887003) + (xy 145.034296 76.799274) (xy 145.143271 76.585401) (xy 145.21745 76.357105) (xy 145.255 76.120025) + (xy 145.255 75.879974) (xy 145.225543 75.693995) (xy 147.499499 75.693995) (xy 147.526418 75.829322) + (xy 147.526421 75.829332) (xy 147.579221 75.956804) (xy 147.579228 75.956817) (xy 147.655885 76.071541) + (xy 147.655888 76.071545) (xy 147.753454 76.169111) (xy 147.753458 76.169114) (xy 147.868182 76.245771) + (xy 147.868195 76.245778) (xy 147.995667 76.298578) (xy 147.995672 76.29858) (xy 147.995676 76.29858) + (xy 147.995677 76.298581) (xy 148.131004 76.3255) (xy 148.131007 76.3255) (xy 148.268995 76.3255) + (xy 148.360041 76.307389) (xy 148.404328 76.29858) (xy 148.531811 76.245775) (xy 148.646542 76.169114) + (xy 148.744114 76.071542) (xy 148.820775 75.956811) (xy 148.87358 75.829328) (xy 148.882389 75.785041) + (xy 148.9005 75.693995) (xy 148.9005 75.556004) (xy 148.873581 75.420677) (xy 148.87358 75.420676) + (xy 148.87358 75.420672) (xy 148.871064 75.414598) (xy 148.820778 75.293195) (xy 148.820771 75.293182) + (xy 148.744114 75.178458) (xy 148.744111 75.178454) (xy 148.646545 75.080888) (xy 148.646541 75.080885) + (xy 148.531817 75.004228) (xy 148.531804 75.004221) (xy 148.404332 74.951421) (xy 148.404322 74.951418) + (xy 148.268995 74.9245) (xy 148.268993 74.9245) (xy 148.131007 74.9245) (xy 148.131005 74.9245) + (xy 147.995677 74.951418) (xy 147.995667 74.951421) (xy 147.868195 75.004221) (xy 147.868182 75.004228) + (xy 147.753458 75.080885) (xy 147.753454 75.080888) (xy 147.655888 75.178454) (xy 147.655885 75.178458) + (xy 147.579228 75.293182) (xy 147.579221 75.293195) (xy 147.526421 75.420667) (xy 147.526418 75.420677) + (xy 147.4995 75.556004) (xy 147.4995 75.556007) (xy 147.4995 75.693993) (xy 147.4995 75.693995) + (xy 147.499499 75.693995) (xy 145.225543 75.693995) (xy 145.217449 75.642893) (xy 145.217449 75.64289) + (xy 145.19969 75.588233) (xy 145.143271 75.414598) (xy 145.034294 75.200722) (xy 144.970557 75.112995) + (xy 144.970556 75.112994) (xy 144.233374 75.850176) (xy 144.219222 75.797358) (xy 144.150104 75.677643) + (xy 144.052357 75.579896) (xy 143.932642 75.510778) (xy 143.879821 75.496624) (xy 144.617003 74.759443) + (xy 144.617003 74.759441) (xy 144.529277 74.695705) (xy 144.315401 74.586728) (xy 144.087105 74.512549) + (xy 143.850025 74.475) (xy 143.609975 74.475) (xy 143.372894 74.512549) (xy 143.144598 74.586728) + (xy 142.950626 74.685563) (xy 142.881957 74.698459) (xy 142.817216 74.672183) (xy 142.776959 74.615076) + (xy 142.773967 74.545271) (xy 142.795955 74.499591) (xy 142.804442 74.488532) (xy 142.920815 74.286969) + (xy 142.977802 74.14939) (xy 143.009879 74.071947) (xy 143.009878 74.071947) (xy 143.009882 74.07194) + (xy 143.070121 73.847126) (xy 143.1005 73.616372) (xy 143.1005 73.383628) (xy 143.070121 73.152874) + (xy 143.014212 72.94422) (xy 143.009882 72.928059) (xy 143.00988 72.928055) (xy 143.007021 72.921153) + (xy 144.7995 72.921153) (xy 144.7995 73.078846) (xy 144.830261 73.233489) (xy 144.830264 73.233501) + (xy 144.890602 73.379172) (xy 144.890609 73.379185) (xy 144.97821 73.510288) (xy 144.978213 73.510292) + (xy 145.089707 73.621786) (xy 145.089711 73.621789) (xy 145.220814 73.70939) (xy 145.220827 73.709397) + (xy 145.366498 73.769735) (xy 145.366503 73.769737) (xy 145.521153 73.800499) (xy 145.521156 73.8005) + (xy 145.521158 73.8005) (xy 145.678844 73.8005) (xy 145.678845 73.800499) (xy 145.833497 73.769737) + (xy 145.979179 73.709394) (xy 146.110289 73.621789) (xy 146.221789 73.510289) (xy 146.309394 73.379179) + (xy 146.316859 73.361158) (xy 146.325416 73.340498) (xy 146.369737 73.233497) (xy 146.4005 73.078842) + (xy 146.4005 72.921158) (xy 146.4005 72.921155) (xy 146.400499 72.921153) (xy 146.380022 72.81821) + (xy 146.369737 72.766503) (xy 146.369735 72.766498) (xy 146.309397 72.620827) (xy 146.30939 72.620814) + (xy 146.221789 72.489711) (xy 146.221786 72.489707) (xy 146.110292 72.378213) (xy 146.110288 72.37821) + (xy 145.979185 72.290609) (xy 145.979172 72.290602) (xy 145.833501 72.230264) (xy 145.833489 72.230261) + (xy 145.678845 72.1995) (xy 145.678842 72.1995) (xy 145.521158 72.1995) (xy 145.521155 72.1995) + (xy 145.36651 72.230261) (xy 145.366498 72.230264) (xy 145.220827 72.290602) (xy 145.220814 72.290609) + (xy 145.089711 72.37821) (xy 145.089707 72.378213) (xy 144.978213 72.489707) (xy 144.97821 72.489711) + (xy 144.890609 72.620814) (xy 144.890602 72.620827) (xy 144.830264 72.766498) (xy 144.830261 72.76651) + (xy 144.7995 72.921153) (xy 143.007021 72.921153) (xy 142.920819 72.713039) (xy 142.920811 72.713023) + (xy 142.804446 72.511475) (xy 142.804443 72.51147) (xy 142.804442 72.511468) (xy 142.702192 72.378213) + (xy 142.662757 72.32682) (xy 142.662751 72.326813) (xy 142.498186 72.162248) (xy 142.498179 72.162242) + (xy 142.31354 72.020564) (xy 142.313538 72.020562) (xy 142.313532 72.020558) (xy 142.313527 72.020555) + (xy 142.313524 72.020553) (xy 142.111976 71.904188) (xy 142.11196 71.90418) (xy 141.896947 71.81512) + (xy 141.729539 71.770263) (xy 141.672126 71.754879) (xy 141.672125 71.754878) (xy 141.672122 71.754878) + (xy 141.441382 71.724501) (xy 141.441377 71.7245) (xy 141.441372 71.7245) (xy 141.208628 71.7245) + (xy 141.208622 71.7245) (xy 141.208617 71.724501) (xy 140.977877 71.754878) (xy 140.753052 71.81512) + (xy 140.538039 71.90418) (xy 140.538023 71.904188) (xy 140.336475 72.020553) (xy 140.336459 72.020564) + (xy 140.15182 72.162242) (xy 140.151813 72.162248) (xy 139.987248 72.326813) (xy 139.987242 72.32682) + (xy 139.845564 72.511459) (xy 139.845553 72.511475) (xy 139.729188 72.713023) (xy 139.72918 72.713039) + (xy 139.64012 72.928052) (xy 139.579878 73.152877) (xy 139.549501 73.383617) (xy 139.5495 73.383634) + (xy 139.5495 73.616365) (xy 139.549501 73.616382) (xy 139.579878 73.847122) (xy 139.64012 74.071947) + (xy 139.72918 74.28696) (xy 139.729188 74.286976) (xy 139.845553 74.488524) (xy 139.845564 74.48854) + (xy 139.987242 74.673179) (xy 139.987248 74.673186) (xy 140.151813 74.837751) (xy 140.151819 74.837756) + (xy 140.336468 74.979442) (xy 140.336475 74.979446) (xy 140.538023 75.095811) (xy 140.538039 75.095819) + (xy 140.753052 75.184879) (xy 140.753054 75.184879) (xy 140.75306 75.184882) (xy 140.977874 75.245121) + (xy 141.208628 75.2755) (xy 141.208635 75.2755) (xy 141.441365 75.2755) (xy 141.441372 75.2755) + (xy 141.672126 75.245121) (xy 141.89694 75.184882) (xy 142.028149 75.130534) (xy 142.11196 75.095819) + (xy 142.111961 75.095817) (xy 142.111969 75.095815) (xy 142.278478 74.99968) (xy 142.346375 74.983208) + (xy 142.412402 75.00606) (xy 142.455593 75.060981) (xy 142.462235 75.130534) (xy 142.440796 75.179951) + (xy 142.425704 75.200724) (xy 142.316728 75.414598) (xy 142.242549 75.642894) (xy 142.205 75.879974) + (xy 142.205 76.120025) (xy 142.242549 76.357105) (xy 142.316728 76.585401) (xy 142.425705 76.799277) + (xy 142.489441 76.887003) (xy 142.489443 76.887003) (xy 143.226624 76.149821) (xy 143.240778 76.202642) + (xy 143.309896 76.322357) (xy 143.407643 76.420104) (xy 143.527358 76.489222) (xy 143.580177 76.503375) + (xy 142.810679 77.272871) (xy 142.788175 77.298654) (xy 142.736204 77.336413) (xy 142.566416 77.506201) + (xy 142.425276 77.700463) (xy 142.316265 77.914406) (xy 142.242063 78.142777) (xy 142.204499 78.379943) + (xy 142.204117 78.384804) (xy 142.201821 78.384623) (xy 142.184815 78.442539) (xy 142.132011 78.488294) + (xy 142.0805 78.4995) (xy 142.021155 78.4995) (xy 141.86651 78.530261) (xy 141.866498 78.530264) + (xy 141.720827 78.590602) (xy 141.720814 78.590609) (xy 141.589711 78.67821) (xy 141.589707 78.678213) + (xy 141.478213 78.789707) (xy 141.47821 78.789711) (xy 141.390609 78.920814) (xy 141.390602 78.920827) + (xy 141.330264 79.066498) (xy 141.330261 79.06651) (xy 141.2995 79.221153) (xy 141.2995 79.378846) + (xy 141.330261 79.533489) (xy 141.330264 79.533501) (xy 141.390602 79.679172) (xy 141.390609 79.679185) + (xy 141.47821 79.810288) (xy 141.478213 79.810292) (xy 141.589707 79.921786) (xy 141.589711 79.921789) + (xy 141.720814 80.00939) (xy 141.720827 80.009397) (xy 141.866498 80.069735) (xy 141.866503 80.069737) + (xy 141.972298 80.090781) (xy 142.021153 80.100499) (xy 142.021156 80.1005) (xy 142.021158 80.1005) + (xy 142.178844 80.1005) (xy 142.259007 80.084554) (xy 142.328598 80.090781) (xy 142.383776 80.133643) + (xy 142.407021 80.199533) (xy 142.393684 80.262466) (xy 142.316265 80.414406) (xy 142.242063 80.642777) + (xy 142.2045 80.879941) (xy 142.2045 81.120058) (xy 142.242063 81.357222) (xy 142.316265 81.585593) + (xy 142.425278 81.79954) (xy 142.43973 81.819431) (xy 142.463211 81.885237) (xy 142.447386 81.953291) + (xy 142.397281 82.001986) (xy 142.328803 82.015862) (xy 142.277413 81.999704) (xy 142.111976 81.904188) + (xy 142.11196 81.90418) (xy 141.896947 81.81512) (xy 141.672122 81.754878) (xy 141.441382 81.724501) + (xy 141.441377 81.7245) (xy 141.441372 81.7245) (xy 141.208628 81.7245) (xy 141.208622 81.7245) + (xy 141.208617 81.724501) (xy 140.977877 81.754878) (xy 140.753052 81.81512) (xy 140.538039 81.90418) + (xy 140.538023 81.904188) (xy 140.336475 82.020553) (xy 140.336459 82.020564) (xy 140.15182 82.162242) + (xy 140.151813 82.162248) (xy 139.987248 82.326813) (xy 139.987242 82.32682) (xy 139.845564 82.511459) + (xy 139.845553 82.511475) (xy 139.729188 82.713023) (xy 139.72918 82.713039) (xy 139.640121 82.928051) + (xy 139.640121 82.928052) (xy 139.640118 82.92806) (xy 139.62336 82.990602) (xy 139.608374 83.046528) + (xy 139.572008 83.106188) (xy 139.509161 83.136716) (xy 139.439785 83.128421) (xy 139.400918 83.102114) + (xy 139.30894 83.010136) (xy 139.308935 83.010132) (xy 139.10195 82.85975) (xy 139.101949 82.859749) + (xy 139.101947 82.859748) (xy 139.02891 82.822533) (xy 138.873975 82.743589) (xy 138.873972 82.743588) + (xy 138.63064 82.664526) (xy 138.504284 82.644513) (xy 138.37793 82.6245) (xy 138.12207 82.6245) + (xy 138.037833 82.637842) (xy 137.869359 82.664526) (xy 137.626027 82.743588) (xy 137.626024 82.743589) + (xy 137.398049 82.85975) (xy 137.191064 83.010132) (xy 137.191059 83.010136) (xy 137.010136 83.191059) + (xy 137.010132 83.191064) (xy 136.85975 83.398049) (xy 136.743589 83.626024) (xy 136.743588 83.626027) + (xy 136.664526 83.869359) (xy 136.6245 84.12207) (xy 133.3755 84.12207) (xy 133.335474 83.869361) + (xy 133.273682 83.679184) (xy 133.256411 83.626027) (xy 133.25641 83.626024) (xy 133.20926 83.533488) + (xy 133.140252 83.398053) (xy 133.061814 83.290092) (xy 132.989867 83.191064) (xy 132.989863 83.191059) + (xy 132.80894 83.010136) (xy 132.808935 83.010132) (xy 132.60195 82.85975) (xy 132.601949 82.859749) + (xy 132.601947 82.859748) (xy 132.52891 82.822533) (xy 132.373975 82.743589) (xy 132.373972 82.743588) + (xy 132.13064 82.664526) (xy 132.004284 82.644513) (xy 131.87793 82.6245) (xy 131.62207 82.6245) + (xy 131.537833 82.637842) (xy 131.369359 82.664526) (xy 131.126027 82.743588) (xy 131.126024 82.743589) + (xy 130.898049 82.85975) (xy 130.691065 83.010131) (xy 130.59908 83.102116) (xy 130.537756 83.1356) + (xy 130.468065 83.130616) (xy 130.412131 83.088744) (xy 130.391626 83.046532) (xy 130.359882 82.92806) + (xy 130.359879 82.928052) (xy 130.270819 82.713039) (xy 130.270811 82.713023) (xy 130.154446 82.511475) + (xy 130.154442 82.511468) (xy 130.012756 82.326819) (xy 130.012751 82.326813) (xy 129.848186 82.162248) + (xy 129.848179 82.162242) (xy 129.66354 82.020564) (xy 129.663538 82.020562) (xy 129.663532 82.020558) + (xy 129.663527 82.020555) (xy 129.663524 82.020553) (xy 129.461976 81.904188) (xy 129.46196 81.90418) + (xy 129.246947 81.81512) (xy 129.022122 81.754878) (xy 128.791382 81.724501) (xy 128.791377 81.7245) + (xy 128.791372 81.7245) (xy 128.558628 81.7245) (xy 128.558622 81.7245) (xy 128.558617 81.724501) + (xy 128.327877 81.754878) (xy 128.103052 81.81512) (xy 127.888039 81.90418) (xy 127.888023 81.904188) + (xy 127.686475 82.020553) (xy 127.686459 82.020564) (xy 127.50182 82.162242) (xy 127.501813 82.162248) + (xy 127.337248 82.326813) (xy 127.337242 82.32682) (xy 127.195564 82.511459) (xy 127.195553 82.511475) + (xy 127.079188 82.713023) (xy 127.07918 82.713039) (xy 126.99012 82.928052) (xy 126.929878 83.152877) + (xy 126.899501 83.383617) (xy 126.8995 83.383634) (xy 124.835411 83.383634) (xy 124.833427 83.378843) + (xy 124.809397 83.320826) (xy 124.80939 83.320814) (xy 124.721789 83.189711) (xy 124.721786 83.189707) + (xy 124.610292 83.078213) (xy 124.610288 83.07821) (xy 124.479185 82.990609) (xy 124.479172 82.990602) + (xy 124.333501 82.930264) (xy 124.333489 82.930261) (xy 124.178845 82.8995) (xy 124.178842 82.8995) + (xy 124.021158 82.8995) (xy 124.021155 82.8995) (xy 123.86651 82.930261) (xy 123.866498 82.930264) + (xy 123.720827 82.990602) (xy 123.720814 82.990609) (xy 123.589711 83.07821) (xy 123.589707 83.078213) + (xy 123.478213 83.189707) (xy 123.47821 83.189711) (xy 123.390609 83.320814) (xy 123.390602 83.320827) + (xy 123.330264 83.466498) (xy 123.330261 83.46651) (xy 123.2995 83.621153) (xy 120.2505 83.621153) + (xy 120.2505 81.443995) (xy 121.099499 81.443995) (xy 121.126418 81.579322) (xy 121.126421 81.579332) + (xy 121.179221 81.706804) (xy 121.179228 81.706817) (xy 121.255885 81.821541) (xy 121.255888 81.821545) + (xy 121.353454 81.919111) (xy 121.353458 81.919114) (xy 121.468182 81.995771) (xy 121.468195 81.995778) + (xy 121.595667 82.048578) (xy 121.595672 82.04858) (xy 121.595676 82.04858) (xy 121.595677 82.048581) + (xy 121.731004 82.0755) (xy 121.731007 82.0755) (xy 121.868995 82.0755) (xy 121.960041 82.057389) + (xy 122.004328 82.04858) (xy 122.131811 81.995775) (xy 122.246542 81.919114) (xy 122.344114 81.821542) + (xy 122.420775 81.706811) (xy 122.47358 81.579328) (xy 122.5005 81.443993) (xy 122.5005 81.306007) + (xy 122.5005 81.306004) (xy 122.473581 81.170677) (xy 122.47358 81.170676) (xy 122.47358 81.170672) + (xy 122.473578 81.170667) (xy 122.420778 81.043195) (xy 122.420771 81.043182) (xy 122.344114 80.928458) + (xy 122.344111 80.928454) (xy 122.246545 80.830888) (xy 122.246541 80.830885) (xy 122.131817 80.754228) + (xy 122.131804 80.754221) (xy 122.004332 80.701421) (xy 122.004322 80.701418) (xy 121.868995 80.6745) + (xy 121.868993 80.6745) (xy 121.731007 80.6745) (xy 121.731005 80.6745) (xy 121.595677 80.701418) + (xy 121.595667 80.701421) (xy 121.468195 80.754221) (xy 121.468182 80.754228) (xy 121.353458 80.830885) + (xy 121.353454 80.830888) (xy 121.255888 80.928454) (xy 121.255885 80.928458) (xy 121.179228 81.043182) + (xy 121.179221 81.043195) (xy 121.126421 81.170667) (xy 121.126418 81.170677) (xy 121.0995 81.306004) + (xy 121.0995 81.306007) (xy 121.0995 81.443993) (xy 121.0995 81.443995) (xy 121.099499 81.443995) + (xy 120.2505 81.443995) (xy 120.2505 75.693995) (xy 121.099499 75.693995) (xy 121.126418 75.829322) + (xy 121.126421 75.829332) (xy 121.179221 75.956804) (xy 121.179228 75.956817) (xy 121.255885 76.071541) + (xy 121.255888 76.071545) (xy 121.353454 76.169111) (xy 121.353458 76.169114) (xy 121.468182 76.245771) + (xy 121.468195 76.245778) (xy 121.595667 76.298578) (xy 121.595672 76.29858) (xy 121.595676 76.29858) + (xy 121.595677 76.298581) (xy 121.731004 76.3255) (xy 121.731007 76.3255) (xy 121.868995 76.3255) + (xy 121.960041 76.307389) (xy 122.004328 76.29858) (xy 122.131811 76.245775) (xy 122.246542 76.169114) + (xy 122.344114 76.071542) (xy 122.420775 75.956811) (xy 122.460398 75.861153) (xy 135.4845 75.861153) + (xy 135.4845 76.018846) (xy 135.515261 76.173489) (xy 135.515264 76.173501) (xy 135.575602 76.319172) + (xy 135.575609 76.319185) (xy 135.66321 76.450288) (xy 135.663213 76.450292) (xy 135.774707 76.561786) + (xy 135.774711 76.561789) (xy 135.905814 76.64939) (xy 135.905827 76.649397) (xy 136.051498 76.709735) + (xy 136.051503 76.709737) (xy 136.206153 76.740499) (xy 136.206156 76.7405) (xy 136.206158 76.7405) + (xy 136.363844 76.7405) (xy 136.363845 76.740499) (xy 136.518497 76.709737) (xy 136.664179 76.649394) + (xy 136.795289 76.561789) (xy 136.906789 76.450289) (xy 136.994394 76.319179) (xy 137.054737 76.173497) + (xy 137.0855 76.018842) (xy 137.0855 75.861158) (xy 137.0855 75.861155) (xy 137.085499 75.861153) + (xy 137.079169 75.829332) (xy 137.054737 75.706503) (xy 137.042783 75.677643) (xy 136.994397 75.560827) + (xy 136.99439 75.560814) (xy 136.906789 75.429711) (xy 136.906786 75.429707) (xy 136.795292 75.318213) + (xy 136.795288 75.31821) (xy 136.664185 75.230609) (xy 136.664172 75.230602) (xy 136.518501 75.170264) + (xy 136.518489 75.170261) (xy 136.363845 75.1395) (xy 136.363842 75.1395) (xy 136.206158 75.1395) + (xy 136.206155 75.1395) (xy 136.05151 75.170261) (xy 136.051498 75.170264) (xy 135.905827 75.230602) + (xy 135.905814 75.230609) (xy 135.774711 75.31821) (xy 135.774707 75.318213) (xy 135.663213 75.429707) + (xy 135.66321 75.429711) (xy 135.575609 75.560814) (xy 135.575602 75.560827) (xy 135.515264 75.706498) + (xy 135.515261 75.70651) (xy 135.4845 75.861153) (xy 122.460398 75.861153) (xy 122.47358 75.829328) + (xy 122.5005 75.693993) (xy 122.5005 75.556007) (xy 122.5005 75.556004) (xy 122.473581 75.420677) + (xy 122.47358 75.420676) (xy 122.47358 75.420672) (xy 122.471064 75.414598) (xy 122.420778 75.293195) + (xy 122.420771 75.293182) (xy 122.344114 75.178458) (xy 122.344111 75.178454) (xy 122.246545 75.080888) + (xy 122.246541 75.080885) (xy 122.131817 75.004228) (xy 122.131804 75.004221) (xy 122.004332 74.951421) + (xy 122.004322 74.951418) (xy 121.868995 74.9245) (xy 121.868993 74.9245) (xy 121.731007 74.9245) + (xy 121.731005 74.9245) (xy 121.595677 74.951418) (xy 121.595667 74.951421) (xy 121.468195 75.004221) + (xy 121.468182 75.004228) (xy 121.353458 75.080885) (xy 121.353454 75.080888) (xy 121.255888 75.178454) + (xy 121.255885 75.178458) (xy 121.179228 75.293182) (xy 121.179221 75.293195) (xy 121.126421 75.420667) + (xy 121.126418 75.420677) (xy 121.0995 75.556004) (xy 121.0995 75.556007) (xy 121.0995 75.693993) + (xy 121.0995 75.693995) (xy 121.099499 75.693995) (xy 120.2505 75.693995) (xy 120.2505 73.383634) + (xy 126.8995 73.383634) (xy 126.8995 73.616365) (xy 126.899501 73.616382) (xy 126.929878 73.847122) + (xy 126.99012 74.071947) (xy 127.07918 74.28696) (xy 127.079188 74.286976) (xy 127.195553 74.488524) + (xy 127.195564 74.48854) (xy 127.337242 74.673179) (xy 127.337248 74.673186) (xy 127.501813 74.837751) + (xy 127.501819 74.837756) (xy 127.686468 74.979442) (xy 127.686475 74.979446) (xy 127.888023 75.095811) + (xy 127.888039 75.095819) (xy 128.103052 75.184879) (xy 128.103054 75.184879) (xy 128.10306 75.184882) + (xy 128.327874 75.245121) (xy 128.558628 75.2755) (xy 128.558635 75.2755) (xy 128.791365 75.2755) + (xy 128.791372 75.2755) (xy 129.022126 75.245121) (xy 129.24694 75.184882) (xy 129.378149 75.130534) + (xy 129.46196 75.095819) (xy 129.461963 75.095817) (xy 129.461969 75.095815) (xy 129.663532 74.979442) + (xy 129.848181 74.837756) (xy 130.012756 74.673181) (xy 130.154442 74.488532) (xy 130.270815 74.286969) + (xy 130.327802 74.14939) (xy 130.359879 74.071947) (xy 130.359878 74.071947) (xy 130.359882 74.07194) + (xy 130.420121 73.847126) (xy 130.4505 73.616372) (xy 130.4505 73.383628) (xy 130.449913 73.379172) + (xy 130.448871 73.37125) (xy 130.447542 73.361153) (xy 130.9845 73.361153) (xy 130.9845 73.518846) + (xy 131.015261 73.673489) (xy 131.015264 73.673501) (xy 131.075602 73.819172) (xy 131.075609 73.819185) + (xy 131.16321 73.950288) (xy 131.163213 73.950292) (xy 131.274707 74.061786) (xy 131.274711 74.061789) + (xy 131.405814 74.14939) (xy 131.405827 74.149397) (xy 131.551498 74.209735) (xy 131.551503 74.209737) + (xy 131.706153 74.240499) (xy 131.706156 74.2405) (xy 131.706158 74.2405) (xy 131.863844 74.2405) + (xy 131.863845 74.240499) (xy 132.018497 74.209737) (xy 132.164179 74.149394) (xy 132.295289 74.061789) + (xy 132.406789 73.950289) (xy 132.494394 73.819179) (xy 132.554737 73.673497) (xy 132.5855 73.518842) + (xy 132.5855 73.361158) (xy 132.5855 73.361155) (xy 132.585499 73.361153) (xy 132.563268 73.249393) + (xy 132.554737 73.206503) (xy 132.536216 73.161788) (xy 132.494397 73.060827) (xy 132.49439 73.060814) + (xy 132.406789 72.929711) (xy 132.406786 72.929707) (xy 132.295292 72.818213) (xy 132.295288 72.81821) + (xy 132.164185 72.730609) (xy 132.164172 72.730602) (xy 132.018501 72.670264) (xy 132.018489 72.670261) + (xy 131.863845 72.6395) (xy 131.863842 72.6395) (xy 131.706158 72.6395) (xy 131.706155 72.6395) + (xy 131.55151 72.670261) (xy 131.551498 72.670264) (xy 131.405827 72.730602) (xy 131.405814 72.730609) + (xy 131.274711 72.81821) (xy 131.274707 72.818213) (xy 131.163213 72.929707) (xy 131.16321 72.929711) + (xy 131.075609 73.060814) (xy 131.075602 73.060827) (xy 131.015264 73.206498) (xy 131.015261 73.20651) + (xy 130.9845 73.361153) (xy 130.447542 73.361153) (xy 130.427181 73.206503) (xy 130.420121 73.152874) + (xy 130.359882 72.92806) (xy 130.357021 72.921153) (xy 130.270819 72.713039) (xy 130.270814 72.71303) + (xy 130.246123 72.670264) (xy 130.154442 72.511468) (xy 130.115833 72.461152) (xy 137.6845 72.461152) + (xy 137.6845 72.618845) (xy 137.715261 72.773488) (xy 137.715264 72.7735) (xy 137.775602 72.919171) + (xy 137.775609 72.919184) (xy 137.86321 73.050287) (xy 137.863213 73.050291) (xy 137.974707 73.161785) + (xy 137.974711 73.161788) (xy 138.105814 73.249389) (xy 138.105827 73.249396) (xy 138.251498 73.309734) + (xy 138.251503 73.309736) (xy 138.406153 73.340498) (xy 138.406156 73.340499) (xy 138.406158 73.340499) + (xy 138.563844 73.340499) (xy 138.563845 73.340498) (xy 138.718497 73.309736) (xy 138.761911 73.291753) + (xy 138.826482 73.265008) (xy 138.864172 73.249396) (xy 138.864172 73.249395) (xy 138.864179 73.249393) + (xy 138.995289 73.161788) (xy 139.106789 73.050288) (xy 139.194394 72.919178) (xy 139.254737 72.773496) + (xy 139.2855 72.618841) (xy 139.2855 72.461157) (xy 139.2855 72.461154) (xy 139.285499 72.461152) + (xy 139.277669 72.421789) (xy 139.254737 72.306502) (xy 139.248151 72.290602) (xy 139.194397 72.160826) + (xy 139.19439 72.160813) (xy 139.106789 72.02971) (xy 139.106786 72.029706) (xy 138.995292 71.918212) + (xy 138.995288 71.918209) (xy 138.864185 71.830608) (xy 138.864172 71.830601) (xy 138.718501 71.770263) + (xy 138.718489 71.77026) (xy 138.563845 71.739499) (xy 138.563842 71.739499) (xy 138.406158 71.739499) + (xy 138.406155 71.739499) (xy 138.25151 71.77026) (xy 138.251498 71.770263) (xy 138.105827 71.830601) + (xy 138.105814 71.830608) (xy 137.974711 71.918209) (xy 137.974707 71.918212) (xy 137.863213 72.029706) + (xy 137.86321 72.02971) (xy 137.775609 72.160813) (xy 137.775602 72.160826) (xy 137.715264 72.306497) + (xy 137.715261 72.306509) (xy 137.6845 72.461152) (xy 130.115833 72.461152) (xy 130.052192 72.378213) + (xy 130.012757 72.32682) (xy 130.012751 72.326813) (xy 129.848186 72.162248) (xy 129.848179 72.162242) + (xy 129.66354 72.020564) (xy 129.663538 72.020562) (xy 129.663532 72.020558) (xy 129.663527 72.020555) + (xy 129.663524 72.020553) (xy 129.461976 71.904188) (xy 129.46196 71.90418) (xy 129.246947 71.81512) + (xy 129.079539 71.770263) (xy 129.022126 71.754879) (xy 129.022125 71.754878) (xy 129.022122 71.754878) + (xy 128.791382 71.724501) (xy 128.791377 71.7245) (xy 128.791372 71.7245) (xy 128.558628 71.7245) + (xy 128.558622 71.7245) (xy 128.558617 71.724501) (xy 128.327877 71.754878) (xy 128.103052 71.81512) + (xy 127.888039 71.90418) (xy 127.888023 71.904188) (xy 127.686475 72.020553) (xy 127.686459 72.020564) + (xy 127.50182 72.162242) (xy 127.501813 72.162248) (xy 127.337248 72.326813) (xy 127.337242 72.32682) + (xy 127.195564 72.511459) (xy 127.195553 72.511475) (xy 127.079188 72.713023) (xy 127.07918 72.713039) + (xy 126.99012 72.928052) (xy 126.929878 73.152877) (xy 126.899501 73.383617) (xy 126.8995 73.383634) + (xy 120.2505 73.383634) (xy 120.2505 71.443995) (xy 121.099499 71.443995) (xy 121.126418 71.579322) + (xy 121.126421 71.579332) (xy 121.179221 71.706804) (xy 121.179228 71.706817) (xy 121.255885 71.821541) + (xy 121.255888 71.821545) (xy 121.353454 71.919111) (xy 121.353458 71.919114) (xy 121.468182 71.995771) + (xy 121.468195 71.995778) (xy 121.595667 72.048578) (xy 121.595672 72.04858) (xy 121.595676 72.04858) + (xy 121.595677 72.048581) (xy 121.731004 72.0755) (xy 121.731007 72.0755) (xy 121.868995 72.0755) + (xy 121.960041 72.057389) (xy 122.004328 72.04858) (xy 122.131811 71.995775) (xy 122.246542 71.919114) + (xy 122.344114 71.821542) (xy 122.411192 71.721153) (xy 123.3995 71.721153) (xy 123.3995 71.878846) + (xy 123.430261 72.033489) (xy 123.430264 72.033501) (xy 123.490602 72.179172) (xy 123.490609 72.179185) + (xy 123.57821 72.310288) (xy 123.578213 72.310292) (xy 123.689707 72.421786) (xy 123.689711 72.421789) + (xy 123.820814 72.50939) (xy 123.820827 72.509397) (xy 123.966498 72.569735) (xy 123.966503 72.569737) + (xy 124.121153 72.600499) (xy 124.121156 72.6005) (xy 124.121158 72.6005) (xy 124.278844 72.6005) + (xy 124.278845 72.600499) (xy 124.433497 72.569737) (xy 124.579179 72.509394) (xy 124.710289 72.421789) + (xy 124.821789 72.310289) (xy 124.909394 72.179179) (xy 124.91641 72.162242) (xy 124.969735 72.033501) + (xy 124.969737 72.033497) (xy 125.0005 71.878842) (xy 125.0005 71.721158) (xy 125.0005 71.721155) + (xy 125.000499 71.721153) (xy 124.969738 71.56651) (xy 124.969737 71.566503) (xy 124.942398 71.5005) + (xy 124.909397 71.420827) (xy 124.90939 71.420814) (xy 124.821789 71.289711) (xy 124.821786 71.289707) + (xy 124.710292 71.178213) (xy 124.710288 71.17821) (xy 124.579185 71.090609) (xy 124.579176 71.090604) + (xy 124.548403 71.077858) (xy 124.548401 71.077857) (xy 124.433501 71.030264) (xy 124.433489 71.030261) + (xy 124.278845 70.9995) (xy 124.278842 70.9995) (xy 124.121158 70.9995) (xy 124.121155 70.9995) + (xy 123.96651 71.030261) (xy 123.966498 71.030264) (xy 123.820827 71.090602) (xy 123.820814 71.090609) + (xy 123.689711 71.17821) (xy 123.689707 71.178213) (xy 123.578213 71.289707) (xy 123.57821 71.289711) + (xy 123.490609 71.420814) (xy 123.490602 71.420827) (xy 123.430264 71.566498) (xy 123.430261 71.56651) + (xy 123.3995 71.721153) (xy 122.411192 71.721153) (xy 122.420775 71.706811) (xy 122.47358 71.579328) + (xy 122.5005 71.443993) (xy 122.5005 71.306007) (xy 122.5005 71.306004) (xy 122.473581 71.170677) + (xy 122.47358 71.170676) (xy 122.47358 71.170672) (xy 122.44623 71.104643) (xy 122.420778 71.043195) + (xy 122.420771 71.043182) (xy 122.344114 70.928458) (xy 122.344111 70.928454) (xy 122.246545 70.830888) + (xy 122.246541 70.830885) (xy 122.131817 70.754228) (xy 122.131804 70.754221) (xy 122.004332 70.701421) + (xy 122.004322 70.701418) (xy 121.868995 70.6745) (xy 121.868993 70.6745) (xy 121.731007 70.6745) + (xy 121.731005 70.6745) (xy 121.595677 70.701418) (xy 121.595667 70.701421) (xy 121.468195 70.754221) + (xy 121.468182 70.754228) (xy 121.353458 70.830885) (xy 121.353454 70.830888) (xy 121.255888 70.928454) + (xy 121.255885 70.928458) (xy 121.179228 71.043182) (xy 121.179221 71.043195) (xy 121.126421 71.170667) + (xy 121.126418 71.170677) (xy 121.0995 71.306004) (xy 121.0995 71.306007) (xy 121.0995 71.443993) + (xy 121.0995 71.443995) (xy 121.099499 71.443995) (xy 120.2505 71.443995) (xy 120.2505 69.649974) + (xy 130.975 69.649974) (xy 130.975 69.890025) (xy 131.012549 70.127105) (xy 131.086728 70.355401) + (xy 131.195705 70.569277) (xy 131.259441 70.657003) (xy 131.259443 70.657003) (xy 131.996624 69.919822) + (xy 132.010778 69.972642) (xy 132.079896 70.092357) (xy 132.177643 70.190104) (xy 132.297358 70.259222) + (xy 132.350177 70.273375) (xy 131.612994 71.010556) (xy 131.612995 71.010557) (xy 131.700722 71.074294) + (xy 131.914598 71.183271) (xy 132.142894 71.25745) (xy 132.379975 71.295) (xy 132.620025 71.295) + (xy 132.857105 71.25745) (xy 133.085401 71.183271) (xy 133.299274 71.074296) (xy 133.387003 71.010556) + (xy 133.387004 71.010556) (xy 132.649822 70.273375) (xy 132.702642 70.259222) (xy 132.822357 70.190104) + (xy 132.920104 70.092357) (xy 132.989222 69.972642) (xy 133.003374 69.919822) (xy 133.772897 70.689345) + (xy 133.798654 70.711824) (xy 133.836414 70.763796) (xy 134.006204 70.933586) (xy 134.200464 71.074724) + (xy 134.259183 71.104643) (xy 134.414406 71.183734) (xy 134.414408 71.183734) (xy 134.414411 71.183736) + (xy 134.642778 71.257937) (xy 134.879941 71.2955) (xy 134.879942 71.2955) (xy 135.120058 71.2955) + (xy 135.120059 71.2955) (xy 135.357222 71.257937) (xy 135.585589 71.183736) (xy 135.799536 71.074724) + (xy 135.993796 70.933586) (xy 136.162319 70.765063) (xy 136.223642 70.731578) (xy 136.293334 70.736562) + (xy 136.337681 70.765063) (xy 136.506204 70.933586) (xy 136.700464 71.074724) (xy 136.759183 71.104643) + (xy 136.914406 71.183734) (xy 136.914408 71.183734) (xy 136.914411 71.183736) (xy 137.142778 71.257937) + (xy 137.379941 71.2955) (xy 137.379942 71.2955) (xy 137.620058 71.2955) (xy 137.620059 71.2955) + (xy 137.857222 71.257937) (xy 138.085589 71.183736) (xy 138.085594 71.183733) (xy 138.085598 71.183732) + (xy 138.267075 71.091264) (xy 138.335744 71.078367) (xy 138.400484 71.104643) (xy 138.426472 71.132857) + (xy 138.47821 71.210288) (xy 138.478213 71.210292) (xy 138.589707 71.321786) (xy 138.589711 71.321789) + (xy 138.720814 71.40939) (xy 138.720827 71.409397) (xy 138.866498 71.469735) (xy 138.866503 71.469737) + (xy 139.021153 71.500499) (xy 139.021156 71.5005) (xy 139.021158 71.5005) (xy 139.178844 71.5005) + (xy 139.178845 71.500499) (xy 139.333497 71.469737) (xy 139.395644 71.443995) (xy 147.499499 71.443995) + (xy 147.526418 71.579322) (xy 147.526421 71.579332) (xy 147.579221 71.706804) (xy 147.579228 71.706817) + (xy 147.655885 71.821541) (xy 147.655888 71.821545) (xy 147.753454 71.919111) (xy 147.753458 71.919114) + (xy 147.868182 71.995771) (xy 147.868195 71.995778) (xy 147.995667 72.048578) (xy 147.995672 72.04858) + (xy 147.995676 72.04858) (xy 147.995677 72.048581) (xy 148.131004 72.0755) (xy 148.131007 72.0755) + (xy 148.268995 72.0755) (xy 148.360041 72.057389) (xy 148.404328 72.04858) (xy 148.531811 71.995775) + (xy 148.646542 71.919114) (xy 148.744114 71.821542) (xy 148.820775 71.706811) (xy 148.87358 71.579328) + (xy 148.9005 71.443993) (xy 148.9005 71.306007) (xy 148.9005 71.306004) (xy 148.873581 71.170677) + (xy 148.87358 71.170676) (xy 148.87358 71.170672) (xy 148.84623 71.104643) (xy 148.820778 71.043195) + (xy 148.820771 71.043182) (xy 148.744114 70.928458) (xy 148.744111 70.928454) (xy 148.646545 70.830888) + (xy 148.646541 70.830885) (xy 148.531817 70.754228) (xy 148.531804 70.754221) (xy 148.404332 70.701421) + (xy 148.404322 70.701418) (xy 148.268995 70.6745) (xy 148.268993 70.6745) (xy 148.131007 70.6745) + (xy 148.131005 70.6745) (xy 147.995677 70.701418) (xy 147.995667 70.701421) (xy 147.868195 70.754221) + (xy 147.868182 70.754228) (xy 147.753458 70.830885) (xy 147.753454 70.830888) (xy 147.655888 70.928454) + (xy 147.655885 70.928458) (xy 147.579228 71.043182) (xy 147.579221 71.043195) (xy 147.526421 71.170667) + (xy 147.526418 71.170677) (xy 147.4995 71.306004) (xy 147.4995 71.306007) (xy 147.4995 71.443993) + (xy 147.4995 71.443995) (xy 147.499499 71.443995) (xy 139.395644 71.443995) (xy 139.451592 71.420821) + (xy 139.479172 71.409397) (xy 139.479172 71.409396) (xy 139.479179 71.409394) (xy 139.610289 71.321789) + (xy 139.642371 71.289707) (xy 139.719845 71.212234) (xy 139.721786 71.210292) (xy 139.721789 71.210289) + (xy 139.809394 71.079179) (xy 139.811418 71.074294) (xy 139.829655 71.030264) (xy 139.869737 70.933497) + (xy 139.9005 70.778842) (xy 139.9005 70.621158) (xy 139.9005 70.621155) (xy 139.900499 70.621153) + (xy 139.869738 70.46651) (xy 139.869737 70.466503) (xy 139.869735 70.466498) (xy 139.809397 70.320827) + (xy 139.80939 70.320814) (xy 139.721789 70.189711) (xy 139.721786 70.189707) (xy 139.610292 70.078213) + (xy 139.610288 70.07821) (xy 139.479185 69.990609) (xy 139.479172 69.990602) (xy 139.333501 69.930264) + (xy 139.333489 69.930261) (xy 139.178845 69.8995) (xy 139.178842 69.8995) (xy 139.1495 69.8995) + (xy 139.082461 69.879815) (xy 139.036706 69.827011) (xy 139.0255 69.7755) (xy 139.0255 69.649941) + (xy 139.01242 69.567358) (xy 138.987937 69.412778) (xy 138.913736 69.184411) (xy 138.913734 69.184408) + (xy 138.913734 69.184406) (xy 138.804723 68.970463) (xy 138.741174 68.882995) (xy 138.663586 68.776204) + (xy 138.493796 68.606414) (xy 138.299536 68.465276) (xy 138.085593 68.356265) (xy 137.857222 68.282063) + (xy 137.620059 68.2445) (xy 137.379941 68.2445) (xy 137.261359 68.263281) (xy 137.142777 68.282063) + (xy 136.914406 68.356265) (xy 136.700463 68.465276) (xy 136.506201 68.606416) (xy 136.337681 68.774937) + (xy 136.276358 68.808422) (xy 136.206666 68.803438) (xy 136.162319 68.774937) (xy 135.993798 68.606416) + (xy 135.993796 68.606414) (xy 135.799536 68.465276) (xy 135.585593 68.356265) (xy 135.357222 68.282063) + (xy 135.120059 68.2445) (xy 134.879941 68.2445) (xy 134.761359 68.263281) (xy 134.642777 68.282063) + (xy 134.414406 68.356265) (xy 134.200463 68.465276) (xy 134.006201 68.606416) (xy 133.836413 68.776204) + (xy 133.798654 68.828175) (xy 133.780544 68.842139) (xy 133.780978 68.842573) (xy 133.003374 69.620176) + (xy 132.989222 69.567358) (xy 132.920104 69.447643) (xy 132.822357 69.349896) (xy 132.702642 69.280778) + (xy 132.649821 69.266624) (xy 133.387003 68.529443) (xy 133.387003 68.529441) (xy 133.299277 68.465705) + (xy 133.085401 68.356728) (xy 132.857105 68.282549) (xy 132.620025 68.245) (xy 132.379975 68.245) + (xy 132.142894 68.282549) (xy 131.914598 68.356728) (xy 131.700729 68.465701) (xy 131.612995 68.529442) + (xy 132.350178 69.266624) (xy 132.297358 69.280778) (xy 132.177643 69.349896) (xy 132.079896 69.447643) + (xy 132.010778 69.567358) (xy 131.996624 69.620177) (xy 131.259442 68.882995) (xy 131.195701 68.970729) + (xy 131.086728 69.184598) (xy 131.012549 69.412894) (xy 130.975 69.649974) (xy 120.2505 69.649974) + (xy 120.2505 67.721153) (xy 123.6995 67.721153) (xy 123.6995 67.878846) (xy 123.730261 68.033489) + (xy 123.730264 68.033501) (xy 123.790602 68.179172) (xy 123.790609 68.179185) (xy 123.87821 68.310288) + (xy 123.878213 68.310292) (xy 123.989707 68.421786) (xy 123.989711 68.421789) (xy 124.120814 68.50939) + (xy 124.120827 68.509397) (xy 124.266498 68.569735) (xy 124.266503 68.569737) (xy 124.421153 68.600499) + (xy 124.421156 68.6005) (xy 124.421158 68.6005) (xy 124.578844 68.6005) (xy 124.578845 68.600499) + (xy 124.733497 68.569737) (xy 124.879179 68.509394) (xy 124.879185 68.50939) (xy 124.932751 68.473599) + (xy 124.972596 68.446974) (xy 125.010289 68.421789) (xy 125.121789 68.310289) (xy 125.209394 68.179179) + (xy 125.269737 68.033497) (xy 125.3005 67.878842) (xy 125.3005 67.721158) (xy 125.3005 67.721155) + (xy 125.300499 67.721153) (xy 125.280734 67.621789) (xy 125.269737 67.566503) (xy 125.246452 67.510288) + (xy 125.209397 67.420827) (xy 125.20939 67.420814) (xy 125.121789 67.289711) (xy 125.121786 67.289707) + (xy 125.010292 67.178213) (xy 125.010288 67.17821) (xy 124.879185 67.090609) (xy 124.879172 67.090602) + (xy 124.733501 67.030264) (xy 124.733489 67.030261) (xy 124.578845 66.9995) (xy 124.578842 66.9995) + (xy 124.421158 66.9995) (xy 124.421155 66.9995) (xy 124.26651 67.030261) (xy 124.266498 67.030264) + (xy 124.120827 67.090602) (xy 124.120814 67.090609) (xy 123.989711 67.17821) (xy 123.989707 67.178213) + (xy 123.878213 67.289707) (xy 123.87821 67.289711) (xy 123.790609 67.420814) (xy 123.790602 67.420827) + (xy 123.730264 67.566498) (xy 123.730261 67.56651) (xy 123.6995 67.721153) (xy 120.2505 67.721153) + (xy 120.2505 66.921153) (xy 131.6995 66.921153) (xy 131.6995 67.078846) (xy 131.730261 67.233489) + (xy 131.730264 67.233501) (xy 131.790602 67.379172) (xy 131.790609 67.379185) (xy 131.87821 67.510288) + (xy 131.878213 67.510292) (xy 131.989707 67.621786) (xy 131.989711 67.621789) (xy 132.120814 67.70939) + (xy 132.120827 67.709397) (xy 132.266498 67.769735) (xy 132.266503 67.769737) (xy 132.421153 67.800499) + (xy 132.421156 67.8005) (xy 132.421158 67.8005) (xy 132.578844 67.8005) (xy 132.578845 67.800499) + (xy 132.733497 67.769737) (xy 132.879179 67.709394) (xy 133.010289 67.621789) (xy 133.121789 67.510289) + (xy 133.209394 67.379179) (xy 133.269737 67.233497) (xy 133.3005 67.078842) (xy 133.3005 66.921158) + (xy 133.3005 66.921155) (xy 133.300499 66.921153) (xy 133.269738 66.76651) (xy 133.269737 66.766503) + (xy 133.269735 66.766498) (xy 133.209397 66.620827) (xy 133.20939 66.620814) (xy 133.121789 66.489711) + (xy 133.121786 66.489707) (xy 133.010292 66.378213) (xy 133.010288 66.37821) (xy 132.879185 66.290609) + (xy 132.879172 66.290602) (xy 132.733501 66.230264) (xy 132.733489 66.230261) (xy 132.578845 66.1995) + (xy 132.578842 66.1995) (xy 132.421158 66.1995) (xy 132.421155 66.1995) (xy 132.26651 66.230261) + (xy 132.266498 66.230264) (xy 132.120827 66.290602) (xy 132.120814 66.290609) (xy 131.989711 66.37821) + (xy 131.989707 66.378213) (xy 131.878213 66.489707) (xy 131.87821 66.489711) (xy 131.790609 66.620814) + (xy 131.790602 66.620827) (xy 131.730264 66.766498) (xy 131.730261 66.76651) (xy 131.6995 66.921153) + (xy 120.2505 66.921153) (xy 120.2505 64.721153) (xy 123.3995 64.721153) (xy 123.3995 64.878846) + (xy 123.430261 65.033489) (xy 123.430264 65.033501) (xy 123.490602 65.179172) (xy 123.490609 65.179185) + (xy 123.57821 65.310288) (xy 123.578213 65.310292) (xy 123.689707 65.421786) (xy 123.689711 65.421789) + (xy 123.820814 65.50939) (xy 123.820827 65.509397) (xy 123.966498 65.569735) (xy 123.966503 65.569737) + (xy 124.121153 65.600499) (xy 124.121156 65.6005) (xy 124.121158 65.6005) (xy 124.278844 65.6005) + (xy 124.278845 65.600499) (xy 124.433497 65.569737) (xy 124.579179 65.509394) (xy 124.710289 65.421789) + (xy 124.821789 65.310289) (xy 124.909394 65.179179) (xy 124.969737 65.033497) (xy 125.0005 64.878842) + (xy 125.0005 64.721158) (xy 125.0005 64.721155) (xy 125.000499 64.721153) (xy 124.969737 64.566503) + (xy 124.950955 64.521158) (xy 124.909397 64.420827) (xy 124.90939 64.420814) (xy 124.821789 64.289711) + (xy 124.821786 64.289707) (xy 124.710292 64.178213) (xy 124.710288 64.17821) (xy 124.579185 64.090609) + (xy 124.579172 64.090602) (xy 124.433501 64.030264) (xy 124.433489 64.030261) (xy 124.278845 63.9995) + (xy 124.278842 63.9995) (xy 124.121158 63.9995) (xy 124.121155 63.9995) (xy 123.96651 64.030261) + (xy 123.966498 64.030264) (xy 123.820827 64.090602) (xy 123.820814 64.090609) (xy 123.689711 64.17821) + (xy 123.689707 64.178213) (xy 123.578213 64.289707) (xy 123.57821 64.289711) (xy 123.490609 64.420814) + (xy 123.490602 64.420827) (xy 123.430264 64.566498) (xy 123.430261 64.56651) (xy 123.3995 64.721153) + (xy 120.2505 64.721153) (xy 120.2505 62.493713) (xy 121.1495 62.493713) (xy 121.1495 62.706287) + (xy 121.182754 62.916243) (xy 121.247738 63.116243) (xy 121.248444 63.118414) (xy 121.344951 63.30782) + (xy 121.46989 63.479786) (xy 121.620213 63.630109) (xy 121.792179 63.755048) (xy 121.792181 63.755049) + (xy 121.792184 63.755051) (xy 121.981588 63.851557) (xy 122.183757 63.917246) (xy 122.393713 63.9505) + (xy 122.393714 63.9505) (xy 122.606286 63.9505) (xy 122.606287 63.9505) (xy 122.816243 63.917246) + (xy 123.018412 63.851557) (xy 123.207816 63.755051) (xy 123.254473 63.721153) (xy 129.8995 63.721153) + (xy 129.8995 63.878846) (xy 129.930261 64.033489) (xy 129.930264 64.033501) (xy 129.990602 64.179172) + (xy 129.990609 64.179185) (xy 130.07821 64.310288) (xy 130.078213 64.310292) (xy 130.189707 64.421786) + (xy 130.189711 64.421789) (xy 130.320814 64.50939) (xy 130.320827 64.509397) (xy 130.458683 64.566498) + (xy 130.466503 64.569737) (xy 130.621153 64.600499) (xy 130.621156 64.6005) (xy 130.621158 64.6005) + (xy 130.778844 64.6005) (xy 130.778845 64.600499) (xy 130.933497 64.569737) (xy 131.05079 64.521153) + (xy 134.0995 64.521153) (xy 134.0995 64.678846) (xy 134.130261 64.833489) (xy 134.130264 64.833501) + (xy 134.190602 64.979172) (xy 134.190609 64.979185) (xy 134.27821 65.110288) (xy 134.278213 65.110292) + (xy 134.389707 65.221786) (xy 134.389711 65.221789) (xy 134.520814 65.30939) (xy 134.520827 65.309397) + (xy 134.666498 65.369735) (xy 134.666503 65.369737) (xy 134.821153 65.400499) (xy 134.821156 65.4005) + (xy 134.821158 65.4005) (xy 134.978844 65.4005) (xy 134.978845 65.400499) (xy 135.133497 65.369737) + (xy 135.279179 65.309394) (xy 135.410289 65.221789) (xy 135.521789 65.110289) (xy 135.609394 64.979179) + (xy 135.669737 64.833497) (xy 135.7005 64.678842) (xy 135.7005 64.521158) (xy 135.7005 64.521155) + (xy 135.700499 64.521153) (xy 135.680734 64.421788) (xy 135.669737 64.366503) (xy 135.637929 64.289711) + (xy 135.609397 64.220827) (xy 135.60939 64.220814) (xy 135.521789 64.089711) (xy 135.521786 64.089707) + (xy 135.410292 63.978213) (xy 135.410288 63.97821) (xy 135.279185 63.890609) (xy 135.279172 63.890602) + (xy 135.133501 63.830264) (xy 135.133489 63.830261) (xy 134.978845 63.7995) (xy 134.978842 63.7995) + (xy 134.821158 63.7995) (xy 134.821155 63.7995) (xy 134.66651 63.830261) (xy 134.666498 63.830264) + (xy 134.520827 63.890602) (xy 134.520814 63.890609) (xy 134.389711 63.97821) (xy 134.389707 63.978213) + (xy 134.278213 64.089707) (xy 134.27821 64.089711) (xy 134.190609 64.220814) (xy 134.190602 64.220827) + (xy 134.130264 64.366498) (xy 134.130261 64.36651) (xy 134.0995 64.521153) (xy 131.05079 64.521153) + (xy 131.079179 64.509394) (xy 131.210289 64.421789) (xy 131.321789 64.310289) (xy 131.409394 64.179179) + (xy 131.469737 64.033497) (xy 131.5005 63.878842) (xy 131.5005 63.721158) (xy 131.5005 63.721155) + (xy 131.500499 63.721153) (xy 131.492272 63.679792) (xy 131.469737 63.566503) (xy 131.43808 63.490075) + (xy 131.430611 63.420606) (xy 131.461886 63.358127) (xy 131.483749 63.339521) (xy 131.510289 63.321789) + (xy 131.621789 63.210289) (xy 131.709394 63.079179) (xy 131.769737 62.933497) (xy 131.8005 62.778842) + (xy 131.8005 62.693713) (xy 146.0495 62.693713) (xy 146.0495 62.906286) (xy 146.076917 63.079394) + (xy 146.082754 63.116243) (xy 146.145001 63.30782) (xy 146.148444 63.318414) (xy 146.244951 63.50782) + (xy 146.36989 63.679786) (xy 146.520213 63.830109) (xy 146.692179 63.955048) (xy 146.692181 63.955049) + (xy 146.692184 63.955051) (xy 146.881588 64.051557) (xy 147.083757 64.117246) (xy 147.293713 64.1505) + (xy 147.293714 64.1505) (xy 147.506286 64.1505) (xy 147.506287 64.1505) (xy 147.716243 64.117246) + (xy 147.918412 64.051557) (xy 148.107816 63.955051) (xy 148.129789 63.939086) (xy 148.279786 63.830109) + (xy 148.279788 63.830106) (xy 148.279792 63.830104) (xy 148.430104 63.679792) (xy 148.430106 63.679788) + (xy 148.430109 63.679786) (xy 148.555048 63.50782) (xy 148.555047 63.50782) (xy 148.555051 63.507816) + (xy 148.651557 63.318412) (xy 148.717246 63.116243) (xy 148.7505 62.906287) (xy 148.7505 62.693713) + (xy 148.717246 62.483757) (xy 148.651557 62.281588) (xy 148.555051 62.092184) (xy 148.555049 62.092181) + (xy 148.555048 62.092179) (xy 148.430109 61.920213) (xy 148.279786 61.76989) (xy 148.10782 61.644951) + (xy 147.918414 61.548444) (xy 147.918413 61.548443) (xy 147.918412 61.548443) (xy 147.716243 61.482754) + (xy 147.716241 61.482753) (xy 147.71624 61.482753) (xy 147.554957 61.457208) (xy 147.506287 61.4495) + (xy 147.293713 61.4495) (xy 147.245042 61.457208) (xy 147.08376 61.482753) (xy 146.881585 61.548444) + (xy 146.692179 61.644951) (xy 146.520213 61.76989) (xy 146.36989 61.920213) (xy 146.244951 62.092179) + (xy 146.148444 62.281585) (xy 146.082753 62.48376) (xy 146.0495 62.693713) (xy 131.8005 62.693713) + (xy 131.8005 62.621158) (xy 131.8005 62.621155) (xy 131.800499 62.621153) (xy 131.775149 62.493713) + (xy 131.769737 62.466503) (xy 131.750796 62.420775) (xy 131.709397 62.320827) (xy 131.70939 62.320814) + (xy 131.621789 62.189711) (xy 131.621786 62.189707) (xy 131.510292 62.078213) (xy 131.510288 62.07821) + (xy 131.379185 61.990609) (xy 131.379172 61.990602) (xy 131.233501 61.930264) (xy 131.233489 61.930261) + (xy 131.078845 61.8995) (xy 131.078842 61.8995) (xy 130.921158 61.8995) (xy 130.921155 61.8995) + (xy 130.76651 61.930261) (xy 130.766498 61.930264) (xy 130.620827 61.990602) (xy 130.620814 61.990609) + (xy 130.489711 62.07821) (xy 130.489707 62.078213) (xy 130.378213 62.189707) (xy 130.37821 62.189711) + (xy 130.290609 62.320814) (xy 130.290602 62.320827) (xy 130.230264 62.466498) (xy 130.230261 62.46651) + (xy 130.1995 62.621153) (xy 130.1995 62.778846) (xy 130.230261 62.933489) (xy 130.230264 62.933501) + (xy 130.261919 63.009924) (xy 130.269388 63.079394) (xy 130.238112 63.141873) (xy 130.216252 63.160476) + (xy 130.189709 63.178212) (xy 130.189704 63.178217) (xy 130.078213 63.289707) (xy 130.07821 63.289711) + (xy 129.990609 63.420814) (xy 129.990602 63.420827) (xy 129.930264 63.566498) (xy 129.930261 63.56651) + (xy 129.8995 63.721153) (xy 123.254473 63.721153) (xy 123.311402 63.679792) (xy 123.379786 63.630109) + (xy 123.379788 63.630106) (xy 123.379792 63.630104) (xy 123.530104 63.479792) (xy 123.530106 63.479788) + (xy 123.530109 63.479786) (xy 123.655048 63.30782) (xy 123.655047 63.30782) (xy 123.655051 63.307816) + (xy 123.751557 63.118412) (xy 123.817246 62.916243) (xy 123.8505 62.706287) (xy 123.8505 62.493713) + (xy 123.817246 62.283757) (xy 123.751557 62.081588) (xy 123.655051 61.892184) (xy 123.638203 61.868995) + (xy 132.174499 61.868995) (xy 132.201418 62.004322) (xy 132.201421 62.004332) (xy 132.254221 62.131804) + (xy 132.254228 62.131817) (xy 132.330885 62.246541) (xy 132.330888 62.246545) (xy 132.428454 62.344111) + (xy 132.428458 62.344114) (xy 132.543182 62.420771) (xy 132.543195 62.420778) (xy 132.653603 62.46651) + (xy 132.670672 62.47358) (xy 132.670676 62.47358) (xy 132.670677 62.473581) (xy 132.806004 62.5005) + (xy 132.806007 62.5005) (xy 132.943995 62.5005) (xy 133.035041 62.482389) (xy 133.079328 62.47358) + (xy 133.206811 62.420775) (xy 133.321542 62.344114) (xy 133.419114 62.246542) (xy 133.495775 62.131811) + (xy 133.54858 62.004328) (xy 133.5755 61.868995) (xy 136.424499 61.868995) (xy 136.451418 62.004322) + (xy 136.451421 62.004332) (xy 136.504221 62.131804) (xy 136.504228 62.131817) (xy 136.580885 62.246541) + (xy 136.580888 62.246545) (xy 136.678454 62.344111) (xy 136.678458 62.344114) (xy 136.793182 62.420771) + (xy 136.793195 62.420778) (xy 136.903603 62.46651) (xy 136.920672 62.47358) (xy 136.920676 62.47358) + (xy 136.920677 62.473581) (xy 137.056004 62.5005) (xy 137.056007 62.5005) (xy 137.193995 62.5005) + (xy 137.285041 62.482389) (xy 137.329328 62.47358) (xy 137.456811 62.420775) (xy 137.571542 62.344114) + (xy 137.669114 62.246542) (xy 137.745775 62.131811) (xy 137.79858 62.004328) (xy 137.8255 61.868993) + (xy 137.8255 61.731007) (xy 137.8255 61.731004) (xy 137.798581 61.595677) (xy 137.79858 61.595676) + (xy 137.79858 61.595672) (xy 137.751808 61.482753) (xy 137.745778 61.468195) (xy 137.745771 61.468182) + (xy 137.669114 61.353458) (xy 137.669111 61.353454) (xy 137.571545 61.255888) (xy 137.571541 61.255885) + (xy 137.456817 61.179228) (xy 137.456804 61.179221) (xy 137.329332 61.126421) (xy 137.329322 61.126418) + (xy 137.193995 61.0995) (xy 137.193993 61.0995) (xy 137.056007 61.0995) (xy 137.056005 61.0995) + (xy 136.920677 61.126418) (xy 136.920667 61.126421) (xy 136.793195 61.179221) (xy 136.793182 61.179228) + (xy 136.678458 61.255885) (xy 136.678454 61.255888) (xy 136.580888 61.353454) (xy 136.580885 61.353458) + (xy 136.504228 61.468182) (xy 136.504221 61.468195) (xy 136.451421 61.595667) (xy 136.451418 61.595677) + (xy 136.4245 61.731004) (xy 136.4245 61.731007) (xy 136.4245 61.868993) (xy 136.4245 61.868995) + (xy 136.424499 61.868995) (xy 133.5755 61.868995) (xy 133.5755 61.868993) (xy 133.5755 61.731007) + (xy 133.5755 61.731004) (xy 133.548581 61.595677) (xy 133.54858 61.595676) (xy 133.54858 61.595672) + (xy 133.501808 61.482753) (xy 133.495778 61.468195) (xy 133.495771 61.468182) (xy 133.419114 61.353458) + (xy 133.419111 61.353454) (xy 133.321545 61.255888) (xy 133.321541 61.255885) (xy 133.206817 61.179228) + (xy 133.206804 61.179221) (xy 133.079332 61.126421) (xy 133.079322 61.126418) (xy 132.943995 61.0995) + (xy 132.943993 61.0995) (xy 132.806007 61.0995) (xy 132.806005 61.0995) (xy 132.670677 61.126418) + (xy 132.670667 61.126421) (xy 132.543195 61.179221) (xy 132.543182 61.179228) (xy 132.428458 61.255885) + (xy 132.428454 61.255888) (xy 132.330888 61.353454) (xy 132.330885 61.353458) (xy 132.254228 61.468182) + (xy 132.254221 61.468195) (xy 132.201421 61.595667) (xy 132.201418 61.595677) (xy 132.1745 61.731004) + (xy 132.1745 61.731007) (xy 132.1745 61.868993) (xy 132.1745 61.868995) (xy 132.174499 61.868995) + (xy 123.638203 61.868995) (xy 123.530104 61.720208) (xy 123.379792 61.569896) (xy 123.379786 61.56989) + (xy 123.20782 61.444951) (xy 123.018414 61.348444) (xy 123.018413 61.348443) (xy 123.018412 61.348443) + (xy 122.816243 61.282754) (xy 122.816241 61.282753) (xy 122.81624 61.282753) (xy 122.6466 61.255885) + (xy 122.606287 61.2495) (xy 122.393713 61.2495) (xy 122.3534 61.255885) (xy 122.18376 61.282753) + (xy 121.981585 61.348444) (xy 121.792179 61.444951) (xy 121.620213 61.56989) (xy 121.46989 61.720213) + (xy 121.344951 61.892179) (xy 121.248444 62.081585) (xy 121.182753 62.28376) (xy 121.152689 62.473578) + (xy 121.1495 62.493713) (xy 120.2505 62.493713) (xy 120.2505 60.3745) (xy 120.270185 60.307461) + (xy 120.322989 60.261706) (xy 120.3745 60.2505) (xy 149.6255 60.2505) ) ) ) @@ -38133,71 +38504,71 @@ (filled_polygon (layer "In2.Cu") (pts - (xy 134.825667 60.270185) (xy 134.871422 60.322989) (xy 134.881366 60.392147) (xy 134.852341 60.455703) - (xy 134.793563 60.493477) (xy 134.782819 60.496117) (xy 134.76651 60.499361) (xy 134.766498 60.499364) - (xy 134.620827 60.559702) (xy 134.620814 60.559709) (xy 134.489711 60.64731) (xy 134.489707 60.647313) - (xy 134.378213 60.758807) (xy 134.37821 60.758811) (xy 134.290609 60.889914) (xy 134.290602 60.889927) - (xy 134.230264 61.035598) (xy 134.230261 61.03561) (xy 134.1995 61.190253) (xy 134.1995 61.347946) - (xy 134.230261 61.502589) (xy 134.230264 61.502601) (xy 134.290602 61.648272) (xy 134.290609 61.648285) - (xy 134.37821 61.779388) (xy 134.378213 61.779392) (xy 134.489707 61.890886) (xy 134.489711 61.890889) - (xy 134.620814 61.97849) (xy 134.620827 61.978497) (xy 134.766498 62.038835) (xy 134.766503 62.038837) - (xy 134.921153 62.069599) (xy 134.921156 62.0696) (xy 134.921158 62.0696) (xy 135.078844 62.0696) - (xy 135.078845 62.069599) (xy 135.233497 62.038837) (xy 135.379179 61.978494) (xy 135.510289 61.890889) - (xy 135.532183 61.868995) (xy 136.424499 61.868995) (xy 136.451418 62.004322) (xy 136.451421 62.004332) - (xy 136.504221 62.131804) (xy 136.504228 62.131817) (xy 136.580885 62.246541) (xy 136.580888 62.246545) - (xy 136.678454 62.344111) (xy 136.678458 62.344114) (xy 136.793182 62.420771) (xy 136.793195 62.420778) - (xy 136.920667 62.473578) (xy 136.920672 62.47358) (xy 136.920676 62.47358) (xy 136.920677 62.473581) - (xy 137.056004 62.5005) (xy 137.056007 62.5005) (xy 137.193995 62.5005) (xy 137.285041 62.482389) - (xy 137.329328 62.47358) (xy 137.456811 62.420775) (xy 137.571542 62.344114) (xy 137.669114 62.246542) - (xy 137.745775 62.131811) (xy 137.79858 62.004328) (xy 137.8255 61.868993) (xy 137.8255 61.731007) - (xy 137.8255 61.731004) (xy 137.798581 61.595677) (xy 137.79858 61.595676) (xy 137.79858 61.595672) - (xy 137.760029 61.502601) (xy 137.745778 61.468195) (xy 137.745771 61.468182) (xy 137.669114 61.353458) - (xy 137.669111 61.353454) (xy 137.571545 61.255888) (xy 137.571541 61.255885) (xy 137.456817 61.179228) - (xy 137.456804 61.179221) (xy 137.329332 61.126421) (xy 137.329322 61.126418) (xy 137.193995 61.0995) - (xy 137.193993 61.0995) (xy 137.056007 61.0995) (xy 137.056005 61.0995) (xy 136.920677 61.126418) - (xy 136.920667 61.126421) (xy 136.793195 61.179221) (xy 136.793182 61.179228) (xy 136.678458 61.255885) - (xy 136.678454 61.255888) (xy 136.580888 61.353454) (xy 136.580885 61.353458) (xy 136.504228 61.468182) - (xy 136.504221 61.468195) (xy 136.451421 61.595667) (xy 136.451418 61.595677) (xy 136.4245 61.731004) - (xy 136.4245 61.731007) (xy 136.4245 61.868993) (xy 136.4245 61.868995) (xy 136.424499 61.868995) - (xy 135.532183 61.868995) (xy 135.621789 61.779389) (xy 135.661404 61.7201) (xy 135.704217 61.656028) - (xy 135.704218 61.656026) (xy 135.706119 61.653179) (xy 135.709394 61.648279) (xy 135.710773 61.644951) - (xy 135.741861 61.569896) (xy 135.769737 61.502597) (xy 135.8005 61.347942) (xy 135.8005 61.190258) - (xy 135.8005 61.190255) (xy 135.800499 61.190253) (xy 135.769738 61.03561) (xy 135.769737 61.035603) - (xy 135.769735 61.035598) (xy 135.709397 60.889927) (xy 135.70939 60.889914) (xy 135.621789 60.758811) - (xy 135.621786 60.758807) (xy 135.510292 60.647313) (xy 135.510288 60.64731) (xy 135.379185 60.559709) - (xy 135.379172 60.559702) (xy 135.233501 60.499364) (xy 135.233489 60.499361) (xy 135.217181 60.496117) - (xy 135.15527 60.463732) (xy 135.120696 60.403016) (xy 135.124435 60.333247) (xy 135.165302 60.276575) - (xy 135.23032 60.250994) (xy 135.241372 60.2505) (xy 149.6255 60.2505) (xy 149.692539 60.270185) - (xy 149.738294 60.322989) (xy 149.7495 60.3745) (xy 149.7495 95.76963) (xy 149.729815 95.836669) - (xy 149.677011 95.882424) (xy 149.607853 95.892368) (xy 149.578048 95.884191) (xy 149.452201 95.832064) - (xy 149.452189 95.832061) (xy 149.297545 95.8013) (xy 149.297542 95.8013) (xy 149.139858 95.8013) - (xy 149.139855 95.8013) (xy 148.98521 95.832061) (xy 148.985198 95.832064) (xy 148.839527 95.892402) - (xy 148.839514 95.892409) (xy 148.708411 95.98001) (xy 148.708407 95.980013) (xy 148.596913 96.091507) - (xy 148.59691 96.091511) (xy 148.509309 96.222614) (xy 148.509302 96.222627) (xy 148.448964 96.368298) - (xy 148.448961 96.36831) (xy 148.4182 96.522953) (xy 148.4182 96.680646) (xy 148.448961 96.835289) - (xy 148.448964 96.835301) (xy 148.509302 96.980972) (xy 148.509309 96.980985) (xy 148.59691 97.112088) - (xy 148.596913 97.112092) (xy 148.708407 97.223586) (xy 148.708411 97.223589) (xy 148.839514 97.31119) - (xy 148.839527 97.311197) (xy 148.985198 97.371535) (xy 148.985203 97.371537) (xy 149.139853 97.402299) - (xy 149.139856 97.4023) (xy 149.139858 97.4023) (xy 149.297544 97.4023) (xy 149.297545 97.402299) - (xy 149.452197 97.371537) (xy 149.578049 97.319407) (xy 149.647517 97.311939) (xy 149.709996 97.343214) - (xy 149.745648 97.403303) (xy 149.7495 97.433969) (xy 149.7495 129.6255) (xy 149.729815 129.692539) - (xy 149.677011 129.738294) (xy 149.6255 129.7495) (xy 120.3745 129.7495) (xy 120.307461 129.729815) - (xy 120.261706 129.677011) (xy 120.2505 129.6255) (xy 120.2505 128.557194) (xy 120.270185 128.490155) - (xy 120.322989 128.4444) (xy 120.392147 128.434456) (xy 120.443391 128.454092) (xy 120.543189 128.520775) - (xy 120.543191 128.520776) (xy 120.543195 128.520778) (xy 120.670667 128.573578) (xy 120.670672 128.57358) - (xy 120.670676 128.57358) (xy 120.670677 128.573581) (xy 120.806004 128.6005) (xy 120.806007 128.6005) - (xy 120.943995 128.6005) (xy 121.035041 128.582389) (xy 121.079328 128.57358) (xy 121.206811 128.520775) - (xy 121.321542 128.444114) (xy 121.419114 128.346542) (xy 121.495775 128.231811) (xy 121.54858 128.104328) - (xy 121.5755 127.968995) (xy 124.424499 127.968995) (xy 124.451418 128.104322) (xy 124.451421 128.104332) - (xy 124.504221 128.231804) (xy 124.504228 128.231817) (xy 124.580885 128.346541) (xy 124.580888 128.346545) - (xy 124.678454 128.444111) (xy 124.678458 128.444114) (xy 124.793182 128.520771) (xy 124.793195 128.520778) - (xy 124.920667 128.573578) (xy 124.920672 128.57358) (xy 124.920676 128.57358) (xy 124.920677 128.573581) - (xy 125.056004 128.6005) (xy 125.056007 128.6005) (xy 125.193995 128.6005) (xy 125.285041 128.582389) - (xy 125.329328 128.57358) (xy 125.456811 128.520775) (xy 125.571542 128.444114) (xy 125.669114 128.346542) - (xy 125.745775 128.231811) (xy 125.79858 128.104328) (xy 125.8255 127.968993) (xy 125.8255 127.831007) - (xy 125.825499 127.831004) (xy 125.823233 127.81961) (xy 125.823233 127.819608) (xy 125.819632 127.801504) - (xy 131.68 127.801504) (xy 131.68 127.95) (xy 132.38 127.95) (xy 132.38 128.45) (xy 131.68 128.45) - (xy 131.68 128.598495) (xy 131.718427 128.791681) (xy 131.71843 128.791693) (xy 131.793807 128.973671) + (xy 149.692539 60.270185) (xy 149.738294 60.322989) (xy 149.7495 60.3745) (xy 149.7495 129.6255) + (xy 149.729815 129.692539) (xy 149.677011 129.738294) (xy 149.6255 129.7495) (xy 131.528567 129.7495) + (xy 131.461528 129.729815) (xy 131.415773 129.677011) (xy 131.405829 129.607853) (xy 131.40695 129.601309) + (xy 131.421363 129.528846) (xy 131.421364 129.528844) (xy 131.421364 129.371155) (xy 131.421363 129.371153) + (xy 131.402585 129.276751) (xy 131.390601 129.216503) (xy 131.357863 129.137466) (xy 131.330261 129.070827) + (xy 131.330254 129.070814) (xy 131.242653 128.939711) (xy 131.24265 128.939707) (xy 131.131156 128.828213) + (xy 131.131152 128.82821) (xy 131.000049 128.740609) (xy 131.000036 128.740602) (xy 130.854365 128.680264) + (xy 130.854353 128.680261) (xy 130.699709 128.6495) (xy 130.699706 128.6495) (xy 130.542022 128.6495) + (xy 130.542019 128.6495) (xy 130.387374 128.680261) (xy 130.387362 128.680264) (xy 130.241691 128.740602) + (xy 130.241678 128.740609) (xy 130.110575 128.82821) (xy 130.110571 128.828213) (xy 129.999077 128.939707) + (xy 129.999074 128.939711) (xy 129.911473 129.070814) (xy 129.911466 129.070827) (xy 129.851128 129.216498) + (xy 129.851125 129.21651) (xy 129.820364 129.371153) (xy 129.820364 129.528846) (xy 129.834778 129.601309) + (xy 129.828551 129.6709) (xy 129.785688 129.726078) (xy 129.719798 129.749322) (xy 129.713161 129.7495) + (xy 120.3745 129.7495) (xy 120.307461 129.729815) (xy 120.261706 129.677011) (xy 120.2505 129.6255) + (xy 120.2505 128.557194) (xy 120.270185 128.490155) (xy 120.322989 128.4444) (xy 120.392147 128.434456) + (xy 120.443391 128.454092) (xy 120.543189 128.520775) (xy 120.543191 128.520776) (xy 120.543195 128.520778) + (xy 120.670667 128.573578) (xy 120.670672 128.57358) (xy 120.670676 128.57358) (xy 120.670677 128.573581) + (xy 120.806004 128.6005) (xy 120.806007 128.6005) (xy 120.943995 128.6005) (xy 121.035041 128.582389) + (xy 121.079328 128.57358) (xy 121.206811 128.520775) (xy 121.321542 128.444114) (xy 121.419114 128.346542) + (xy 121.495775 128.231811) (xy 121.54858 128.104328) (xy 121.5755 127.968995) (xy 124.424499 127.968995) + (xy 124.451418 128.104322) (xy 124.451421 128.104332) (xy 124.504221 128.231804) (xy 124.504228 128.231817) + (xy 124.580885 128.346541) (xy 124.580888 128.346545) (xy 124.678454 128.444111) (xy 124.678458 128.444114) + (xy 124.793182 128.520771) (xy 124.793195 128.520778) (xy 124.920667 128.573578) (xy 124.920672 128.57358) + (xy 124.920676 128.57358) (xy 124.920677 128.573581) (xy 125.056004 128.6005) (xy 125.056007 128.6005) + (xy 125.193995 128.6005) (xy 125.285041 128.582389) (xy 125.329328 128.57358) (xy 125.456811 128.520775) + (xy 125.571542 128.444114) (xy 125.669114 128.346542) (xy 125.745775 128.231811) (xy 125.79858 128.104328) + (xy 125.8255 127.968993) (xy 125.8255 127.831007) (xy 125.8255 127.831004) (xy 125.825499 127.831002) + (xy 125.799791 127.701757) (xy 125.798581 127.695677) (xy 125.79858 127.695676) (xy 125.79858 127.695672) + (xy 125.793604 127.683658) (xy 125.793602 127.683653) (xy 126.3995 127.683653) (xy 126.3995 127.841346) + (xy 126.430261 127.995989) (xy 126.430264 127.996001) (xy 126.490602 128.141672) (xy 126.490609 128.141685) + (xy 126.57821 128.272788) (xy 126.578213 128.272792) (xy 126.689707 128.384286) (xy 126.689711 128.384289) + (xy 126.820814 128.47189) (xy 126.820827 128.471897) (xy 126.938821 128.520771) (xy 126.966503 128.532237) + (xy 127.121153 128.562999) (xy 127.121156 128.563) (xy 127.121158 128.563) (xy 127.278844 128.563) + (xy 127.278845 128.562999) (xy 127.433497 128.532237) (xy 127.579179 128.471894) (xy 127.710289 128.384289) + (xy 127.744078 128.3505) (xy 127.783622 128.310957) (xy 127.821786 128.272792) (xy 127.821789 128.272789) + (xy 127.909394 128.141679) (xy 127.969737 127.995997) (xy 128.0005 127.841342) (xy 128.0005 127.683658) + (xy 128.0005 127.683655) (xy 128.000499 127.683653) (xy 127.977533 127.568195) (xy 127.969737 127.529003) + (xy 127.953381 127.489515) (xy 127.909397 127.383327) (xy 127.90939 127.383314) (xy 127.821789 127.252211) + (xy 127.821786 127.252207) (xy 127.710292 127.140713) (xy 127.710288 127.14071) (xy 127.579185 127.053109) + (xy 127.579172 127.053102) (xy 127.433501 126.992764) (xy 127.433489 126.992761) (xy 127.278845 126.962) + (xy 127.278842 126.962) (xy 127.121158 126.962) (xy 127.121155 126.962) (xy 126.96651 126.992761) + (xy 126.966498 126.992764) (xy 126.820827 127.053102) (xy 126.820814 127.053109) (xy 126.689711 127.14071) + (xy 126.689707 127.140713) (xy 126.578213 127.252207) (xy 126.57821 127.252211) (xy 126.490609 127.383314) + (xy 126.490602 127.383327) (xy 126.430264 127.528998) (xy 126.430261 127.52901) (xy 126.3995 127.683653) + (xy 125.793602 127.683653) (xy 125.745778 127.568195) (xy 125.745771 127.568182) (xy 125.669114 127.453458) + (xy 125.669111 127.453454) (xy 125.571545 127.355888) (xy 125.571541 127.355885) (xy 125.456817 127.279228) + (xy 125.456804 127.279221) (xy 125.329332 127.226421) (xy 125.329322 127.226418) (xy 125.193995 127.1995) + (xy 125.193993 127.1995) (xy 125.056007 127.1995) (xy 125.056005 127.1995) (xy 124.920677 127.226418) + (xy 124.920667 127.226421) (xy 124.793195 127.279221) (xy 124.793182 127.279228) (xy 124.678458 127.355885) + (xy 124.678454 127.355888) (xy 124.580888 127.453454) (xy 124.580885 127.453458) (xy 124.504228 127.568182) + (xy 124.504221 127.568195) (xy 124.451421 127.695667) (xy 124.451418 127.695677) (xy 124.4245 127.831004) + (xy 124.4245 127.831007) (xy 124.4245 127.968993) (xy 124.4245 127.968995) (xy 124.424499 127.968995) + (xy 121.5755 127.968995) (xy 121.5755 127.968993) (xy 121.5755 127.831007) (xy 121.5755 127.831004) + (xy 121.548581 127.695677) (xy 121.54858 127.695676) (xy 121.54858 127.695672) (xy 121.543604 127.683658) + (xy 121.495778 127.568195) (xy 121.495771 127.568182) (xy 121.419114 127.453458) (xy 121.419111 127.453454) + (xy 121.321545 127.355888) (xy 121.321541 127.355885) (xy 121.206817 127.279228) (xy 121.206804 127.279221) + (xy 121.079332 127.226421) (xy 121.079322 127.226418) (xy 120.943995 127.1995) (xy 120.943993 127.1995) + (xy 120.806007 127.1995) (xy 120.806005 127.1995) (xy 120.670677 127.226418) (xy 120.670667 127.226421) + (xy 120.543195 127.279221) (xy 120.543182 127.279228) (xy 120.443391 127.345907) (xy 120.376713 127.366785) + (xy 120.309333 127.3483) (xy 120.262643 127.296321) (xy 120.2505 127.242805) (xy 120.2505 126.841158) + (xy 131.448035 126.841158) (xy 131.448035 126.998851) (xy 131.478796 127.153494) (xy 131.478799 127.153506) + (xy 131.539137 127.299177) (xy 131.539144 127.29919) (xy 131.626744 127.430292) (xy 131.626745 127.430293) + (xy 131.626746 127.430294) (xy 131.685969 127.489517) (xy 131.719453 127.550838) (xy 131.717422 127.6019) + (xy 131.719617 127.602337) (xy 131.68 127.801504) (xy 131.68 127.95) (xy 132.38 127.95) (xy 132.38 128.45) + (xy 131.68 128.45) (xy 131.68 128.598495) (xy 131.718427 128.791681) (xy 131.71843 128.791693) (xy 131.793807 128.973671) (xy 131.793814 128.973684) (xy 131.903248 129.137462) (xy 131.903251 129.137466) (xy 132.042533 129.276748) (xy 132.042537 129.276751) (xy 132.206315 129.386185) (xy 132.206328 129.386192) (xy 132.388308 129.461569) (xy 132.43 129.469862) (xy 132.43 128.666988) (xy 132.43994 128.684205) (xy 132.495795 128.74006) @@ -38231,32 +38602,8 @@ (xy 140.433814 127.426315) (xy 140.433807 127.426328) (xy 140.35843 127.608306) (xy 140.358427 127.608318) (xy 140.32 127.801504) (xy 133.679999 127.801504) (xy 133.641572 127.608318) (xy 133.641569 127.608306) (xy 133.566192 127.426328) (xy 133.566185 127.426315) (xy 133.456751 127.262537) (xy 133.456748 127.262533) - (xy 133.317466 127.123251) (xy 133.317462 127.123248) (xy 133.153684 127.013814) (xy 133.153671 127.013807) - (xy 132.971691 126.938429) (xy 132.971683 126.938427) (xy 132.93 126.930135) (xy 132.93 127.733011) - (xy 132.92006 127.715795) (xy 132.864205 127.65994) (xy 132.795796 127.620444) (xy 132.719496 127.6) - (xy 132.640504 127.6) (xy 132.564204 127.620444) (xy 132.495795 127.65994) (xy 132.43994 127.715795) - (xy 132.43 127.733011) (xy 132.43 126.930136) (xy 132.429999 126.930135) (xy 132.388316 126.938427) - (xy 132.388308 126.938429) (xy 132.206328 127.013807) (xy 132.206315 127.013814) (xy 132.042537 127.123248) - (xy 132.042533 127.123251) (xy 131.903251 127.262533) (xy 131.903248 127.262537) (xy 131.793814 127.426315) - (xy 131.793807 127.426328) (xy 131.71843 127.608306) (xy 131.718427 127.608318) (xy 131.68 127.801504) - (xy 125.819632 127.801504) (xy 125.81051 127.75565) (xy 125.79858 127.695672) (xy 125.798578 127.695667) - (xy 125.745778 127.568195) (xy 125.745771 127.568182) (xy 125.669114 127.453458) (xy 125.669111 127.453454) - (xy 125.571545 127.355888) (xy 125.571541 127.355885) (xy 125.456817 127.279228) (xy 125.456804 127.279221) - (xy 125.329332 127.226421) (xy 125.329322 127.226418) (xy 125.193995 127.1995) (xy 125.193993 127.1995) - (xy 125.056007 127.1995) (xy 125.056005 127.1995) (xy 124.920677 127.226418) (xy 124.920667 127.226421) - (xy 124.793195 127.279221) (xy 124.793182 127.279228) (xy 124.678458 127.355885) (xy 124.678454 127.355888) - (xy 124.580888 127.453454) (xy 124.580885 127.453458) (xy 124.504228 127.568182) (xy 124.504221 127.568195) - (xy 124.451421 127.695667) (xy 124.451418 127.695677) (xy 124.4245 127.831004) (xy 124.4245 127.831006) - (xy 124.4245 127.831007) (xy 124.4245 127.968993) (xy 124.4245 127.968995) (xy 124.424499 127.968995) - (xy 121.5755 127.968995) (xy 121.5755 127.968993) (xy 121.5755 127.831007) (xy 121.5755 127.831006) - (xy 121.5755 127.831004) (xy 121.548581 127.695677) (xy 121.54858 127.695676) (xy 121.54858 127.695672) - (xy 121.548578 127.695667) (xy 121.495778 127.568195) (xy 121.495771 127.568182) (xy 121.419114 127.453458) - (xy 121.419111 127.453454) (xy 121.321545 127.355888) (xy 121.321541 127.355885) (xy 121.206817 127.279228) - (xy 121.206804 127.279221) (xy 121.079332 127.226421) (xy 121.079322 127.226418) (xy 120.943995 127.1995) - (xy 120.943993 127.1995) (xy 120.806007 127.1995) (xy 120.806005 127.1995) (xy 120.670677 127.226418) - (xy 120.670667 127.226421) (xy 120.543195 127.279221) (xy 120.543182 127.279228) (xy 120.443391 127.345907) - (xy 120.376713 127.366785) (xy 120.309333 127.3483) (xy 120.262643 127.296321) (xy 120.2505 127.242805) - (xy 120.2505 126.893713) (xy 145.6495 126.893713) (xy 145.6495 127.106286) (xy 145.679598 127.296321) + (xy 133.317463 127.123248) (xy 133.153676 127.01381) (xy 133.125579 127.002171) (xy 133.071177 126.958328) + (xy 133.049673 126.893713) (xy 145.6495 126.893713) (xy 145.6495 127.106286) (xy 145.679598 127.296321) (xy 145.682754 127.316243) (xy 145.692392 127.345907) (xy 145.748444 127.518414) (xy 145.844951 127.70782) (xy 145.96989 127.879786) (xy 146.120213 128.030109) (xy 146.292179 128.155048) (xy 146.292181 128.155049) (xy 146.292184 128.155051) (xy 146.481588 128.251557) (xy 146.683757 128.317246) (xy 146.893713 128.3505) @@ -38271,152 +38618,187 @@ (xy 147.316241 125.682753) (xy 147.31624 125.682753) (xy 147.154957 125.657208) (xy 147.106287 125.6495) (xy 146.893713 125.6495) (xy 146.845042 125.657208) (xy 146.68376 125.682753) (xy 146.481585 125.748444) (xy 146.292179 125.844951) (xy 146.120213 125.96989) (xy 145.96989 126.120213) (xy 145.844951 126.292179) - (xy 145.748444 126.481585) (xy 145.682753 126.68376) (xy 145.6495 126.893713) (xy 120.2505 126.893713) - (xy 120.2505 125.446453) (xy 124.9695 125.446453) (xy 124.9695 125.604146) (xy 125.000261 125.758789) - (xy 125.000264 125.758801) (xy 125.060602 125.904472) (xy 125.060609 125.904485) (xy 125.14821 126.035588) - (xy 125.148213 126.035592) (xy 125.259707 126.147086) (xy 125.259711 126.147089) (xy 125.390814 126.23469) - (xy 125.390827 126.234697) (xy 125.529603 126.292179) (xy 125.536503 126.295037) (xy 125.691153 126.325799) - (xy 125.691156 126.3258) (xy 125.691158 126.3258) (xy 125.848844 126.3258) (xy 125.848845 126.325799) - (xy 126.003497 126.295037) (xy 126.149179 126.234694) (xy 126.280289 126.147089) (xy 126.391789 126.035589) - (xy 126.424821 125.986153) (xy 137.9495 125.986153) (xy 137.9495 126.143846) (xy 137.980261 126.298489) - (xy 137.980264 126.298501) (xy 138.040602 126.444172) (xy 138.040609 126.444185) (xy 138.12821 126.575288) - (xy 138.128213 126.575292) (xy 138.239707 126.686786) (xy 138.239711 126.686789) (xy 138.370814 126.77439) - (xy 138.370827 126.774397) (xy 138.516498 126.834735) (xy 138.516503 126.834737) (xy 138.671153 126.865499) - (xy 138.671156 126.8655) (xy 138.671158 126.8655) (xy 138.828844 126.8655) (xy 138.828845 126.865499) - (xy 138.983497 126.834737) (xy 139.129179 126.774394) (xy 139.260289 126.686789) (xy 139.371789 126.575289) - (xy 139.459394 126.444179) (xy 139.519737 126.298497) (xy 139.5505 126.143842) (xy 139.5505 125.986158) - (xy 139.5505 125.986155) (xy 139.550499 125.986153) (xy 139.535585 125.911175) (xy 139.519737 125.831503) - (xy 139.489623 125.758801) (xy 139.459397 125.685827) (xy 139.45939 125.685814) (xy 139.371789 125.554711) - (xy 139.371786 125.554707) (xy 139.260292 125.443213) (xy 139.260288 125.44321) (xy 139.129185 125.355609) - (xy 139.129172 125.355602) (xy 138.983501 125.295264) (xy 138.983489 125.295261) (xy 138.828845 125.2645) - (xy 138.828842 125.2645) (xy 138.671158 125.2645) (xy 138.671155 125.2645) (xy 138.51651 125.295261) - (xy 138.516498 125.295264) (xy 138.370827 125.355602) (xy 138.370814 125.355609) (xy 138.239711 125.44321) - (xy 138.239707 125.443213) (xy 138.128213 125.554707) (xy 138.12821 125.554711) (xy 138.040609 125.685814) - (xy 138.040602 125.685827) (xy 137.980264 125.831498) (xy 137.980261 125.83151) (xy 137.9495 125.986153) - (xy 126.424821 125.986153) (xy 126.435688 125.96989) (xy 126.474921 125.911175) (xy 126.474921 125.911174) - (xy 126.479389 125.904486) (xy 126.47939 125.904485) (xy 126.479394 125.904479) (xy 126.539737 125.758797) - (xy 126.5705 125.604142) (xy 126.5705 125.446458) (xy 126.5705 125.446455) (xy 126.570499 125.446453) - (xy 126.540425 125.295263) (xy 126.539737 125.291803) (xy 126.504802 125.207462) (xy 126.479397 125.146127) - (xy 126.47939 125.146114) (xy 126.391789 125.015011) (xy 126.391786 125.015007) (xy 126.280292 124.903513) - (xy 126.280288 124.90351) (xy 126.149185 124.815909) (xy 126.149172 124.815902) (xy 126.003501 124.755564) - (xy 126.003489 124.755561) (xy 125.848845 124.7248) (xy 125.848842 124.7248) (xy 125.691158 124.7248) - (xy 125.691155 124.7248) (xy 125.53651 124.755561) (xy 125.536498 124.755564) (xy 125.390827 124.815902) - (xy 125.390814 124.815909) (xy 125.259711 124.90351) (xy 125.259707 124.903513) (xy 125.148213 125.015007) - (xy 125.14821 125.015011) (xy 125.060609 125.146114) (xy 125.060602 125.146127) (xy 125.000264 125.291798) - (xy 125.000261 125.29181) (xy 124.9695 125.446453) (xy 120.2505 125.446453) (xy 120.2505 122.393713) - (xy 121.6495 122.393713) (xy 121.6495 122.606287) (xy 121.682754 122.816243) (xy 121.741267 122.996328) - (xy 121.748444 123.018414) (xy 121.844951 123.20782) (xy 121.96989 123.379786) (xy 122.120213 123.530109) - (xy 122.292179 123.655048) (xy 122.292181 123.655049) (xy 122.292184 123.655051) (xy 122.481588 123.751557) - (xy 122.683757 123.817246) (xy 122.893713 123.8505) (xy 122.893714 123.8505) (xy 123.106286 123.8505) - (xy 123.106287 123.8505) (xy 123.316243 123.817246) (xy 123.518412 123.751557) (xy 123.707816 123.655051) - (xy 123.738739 123.632584) (xy 123.879786 123.530109) (xy 123.879788 123.530106) (xy 123.879792 123.530104) - (xy 124.030104 123.379792) (xy 124.030106 123.379788) (xy 124.030109 123.379786) (xy 124.155048 123.20782) - (xy 124.155047 123.20782) (xy 124.155051 123.207816) (xy 124.242467 123.036253) (xy 128.4162 123.036253) - (xy 128.4162 123.193946) (xy 128.446961 123.348589) (xy 128.446964 123.348601) (xy 128.507302 123.494272) - (xy 128.507309 123.494285) (xy 128.59491 123.625388) (xy 128.594913 123.625392) (xy 128.706407 123.736886) - (xy 128.706411 123.736889) (xy 128.837514 123.82449) (xy 128.837527 123.824497) (xy 128.983198 123.884835) - (xy 128.983203 123.884837) (xy 129.137853 123.915599) (xy 129.137856 123.9156) (xy 129.137858 123.9156) - (xy 129.295544 123.9156) (xy 129.295545 123.915599) (xy 129.450197 123.884837) (xy 129.595879 123.824494) - (xy 129.726989 123.736889) (xy 129.838489 123.625389) (xy 129.926094 123.494279) (xy 129.976949 123.371504) - (xy 131.68 123.371504) (xy 131.68 123.77) (xy 132.38 123.77) (xy 132.38 124.27) (xy 131.68 124.27) - (xy 131.68 124.668495) (xy 131.718427 124.861681) (xy 131.71843 124.861693) (xy 131.793807 125.043671) - (xy 131.793814 125.043684) (xy 131.903248 125.207462) (xy 131.903251 125.207466) (xy 132.042533 125.346748) - (xy 132.042537 125.346751) (xy 132.206315 125.456185) (xy 132.206328 125.456192) (xy 132.388308 125.531569) - (xy 132.43 125.539862) (xy 132.43 124.736988) (xy 132.43994 124.754205) (xy 132.495795 124.81006) - (xy 132.564204 124.849556) (xy 132.640504 124.87) (xy 132.719496 124.87) (xy 132.795796 124.849556) - (xy 132.864205 124.81006) (xy 132.92006 124.754205) (xy 132.93 124.736988) (xy 132.93 125.539862) - (xy 132.97169 125.531569) (xy 132.971692 125.531569) (xy 133.153671 125.456192) (xy 133.153684 125.456185) - (xy 133.317462 125.346751) (xy 133.317466 125.346748) (xy 133.456748 125.207466) (xy 133.456751 125.207462) - (xy 133.569574 125.038613) (xy 133.571007 125.03957) (xy 133.614198 124.99558) (xy 133.682332 124.980103) - (xy 133.748018 125.003919) (xy 133.750089 125.005697) (xy 133.750189 125.005568) (xy 133.75663 125.01051) - (xy 133.756635 125.010515) (xy 133.887865 125.086281) (xy 134.034234 125.1255) (xy 134.034236 125.1255) - (xy 134.185764 125.1255) (xy 134.185766 125.1255) (xy 134.332135 125.086281) (xy 134.463365 125.010515) - (xy 134.570515 124.903365) (xy 134.646281 124.772135) (xy 134.6855 124.625766) (xy 134.6855 124.474234) - (xy 139.3145 124.474234) (xy 139.3145 124.625765) (xy 139.353719 124.772136) (xy 139.375615 124.81006) - (xy 139.429485 124.903365) (xy 139.536635 125.010515) (xy 139.667865 125.086281) (xy 139.814234 125.1255) - (xy 139.814236 125.1255) (xy 139.965764 125.1255) (xy 139.965766 125.1255) (xy 140.112135 125.086281) - (xy 140.243365 125.010515) (xy 140.243372 125.010507) (xy 140.249811 125.005568) (xy 140.252044 125.008478) - (xy 140.298258 124.982865) (xy 140.36798 124.987411) (xy 140.424176 125.02893) (xy 140.430394 125.038634) - (xy 140.430426 125.038613) (xy 140.543248 125.207462) (xy 140.543251 125.207466) (xy 140.682533 125.346748) - (xy 140.682537 125.346751) (xy 140.846315 125.456185) (xy 140.846328 125.456192) (xy 141.028308 125.531569) - (xy 141.07 125.539862) (xy 141.07 124.736988) (xy 141.07994 124.754205) (xy 141.135795 124.81006) - (xy 141.204204 124.849556) (xy 141.280504 124.87) (xy 141.359496 124.87) (xy 141.435796 124.849556) - (xy 141.504205 124.81006) (xy 141.56006 124.754205) (xy 141.57 124.736988) (xy 141.57 125.539862) - (xy 141.61169 125.531569) (xy 141.611692 125.531569) (xy 141.793671 125.456192) (xy 141.793684 125.456185) - (xy 141.957462 125.346751) (xy 141.957466 125.346748) (xy 142.096748 125.207466) (xy 142.096751 125.207462) - (xy 142.206185 125.043684) (xy 142.206192 125.043671) (xy 142.281569 124.861693) (xy 142.281572 124.861681) - (xy 142.319999 124.668495) (xy 142.32 124.668492) (xy 142.32 124.27) (xy 141.62 124.27) (xy 141.62 123.77) - (xy 142.32 123.77) (xy 142.32 123.371508) (xy 142.319999 123.371504) (xy 142.281572 123.178318) - (xy 142.281569 123.178306) (xy 142.206192 122.996328) (xy 142.206185 122.996315) (xy 142.096751 122.832537) - (xy 142.096748 122.832533) (xy 141.957466 122.693251) (xy 141.957462 122.693248) (xy 141.793684 122.583814) - (xy 141.793671 122.583807) (xy 141.679206 122.536395) (xy 141.611691 122.508429) (xy 141.611683 122.508427) - (xy 141.57 122.500135) (xy 141.57 123.303011) (xy 141.56006 123.285795) (xy 141.504205 123.22994) - (xy 141.435796 123.190444) (xy 141.359496 123.17) (xy 141.280504 123.17) (xy 141.204204 123.190444) - (xy 141.135795 123.22994) (xy 141.07994 123.285795) (xy 141.07 123.303011) (xy 141.07 122.500136) - (xy 141.069999 122.500135) (xy 141.028316 122.508427) (xy 141.028308 122.508429) (xy 140.846328 122.583807) - (xy 140.846315 122.583814) (xy 140.682537 122.693248) (xy 140.682533 122.693251) (xy 140.543251 122.832533) - (xy 140.543248 122.832537) (xy 140.433814 122.996315) (xy 140.433807 122.996328) (xy 140.35843 123.178306) - (xy 140.358427 123.178318) (xy 140.32 123.371504) (xy 140.32 123.77) (xy 141.02 123.77) (xy 141.02 124.27) - (xy 140.464464 124.27) (xy 140.397425 124.250315) (xy 140.357077 124.208) (xy 140.350517 124.196638) - (xy 140.350513 124.196633) (xy 140.243367 124.089487) (xy 140.243365 124.089485) (xy 140.165162 124.044334) - (xy 140.112136 124.013719) (xy 140.03895 123.994109) (xy 139.965766 123.9745) (xy 139.814234 123.9745) - (xy 139.667863 124.013719) (xy 139.536635 124.089485) (xy 139.536632 124.089487) (xy 139.429487 124.196632) - (xy 139.429485 124.196635) (xy 139.353719 124.327863) (xy 139.3145 124.474234) (xy 134.6855 124.474234) - (xy 134.646281 124.327865) (xy 134.570515 124.196635) (xy 134.463365 124.089485) (xy 134.385162 124.044334) - (xy 134.332136 124.013719) (xy 134.25895 123.994109) (xy 134.185766 123.9745) (xy 134.034234 123.9745) - (xy 133.887863 124.013719) (xy 133.756635 124.089485) (xy 133.756632 124.089487) (xy 133.649486 124.196633) - (xy 133.649482 124.196638) (xy 133.642923 124.208) (xy 133.592356 124.256216) (xy 133.535536 124.27) - (xy 132.98 124.27) (xy 132.98 123.77) (xy 133.68 123.77) (xy 133.68 123.371508) (xy 133.679999 123.371504) - (xy 133.641572 123.178318) (xy 133.641569 123.178306) (xy 133.566192 122.996328) (xy 133.566185 122.996315) - (xy 133.456751 122.832537) (xy 133.456748 122.832533) (xy 133.317466 122.693251) (xy 133.317462 122.693248) - (xy 133.153684 122.583814) (xy 133.153671 122.583807) (xy 132.971691 122.508429) (xy 132.971683 122.508427) - (xy 132.93 122.500135) (xy 132.93 123.303011) (xy 132.92006 123.285795) (xy 132.864205 123.22994) - (xy 132.795796 123.190444) (xy 132.719496 123.17) (xy 132.640504 123.17) (xy 132.564204 123.190444) - (xy 132.495795 123.22994) (xy 132.43994 123.285795) (xy 132.43 123.303011) (xy 132.43 122.500136) - (xy 132.429999 122.500135) (xy 132.388316 122.508427) (xy 132.388308 122.508429) (xy 132.206328 122.583807) - (xy 132.206315 122.583814) (xy 132.042537 122.693248) (xy 132.042533 122.693251) (xy 131.903251 122.832533) - (xy 131.903248 122.832537) (xy 131.793814 122.996315) (xy 131.793807 122.996328) (xy 131.71843 123.178306) - (xy 131.718427 123.178318) (xy 131.68 123.371504) (xy 129.976949 123.371504) (xy 129.986437 123.348597) - (xy 130.0172 123.193942) (xy 130.0172 123.036258) (xy 130.0172 123.036255) (xy 130.017199 123.036253) - (xy 129.986438 122.88161) (xy 129.986437 122.881603) (xy 129.973347 122.85) (xy 129.926097 122.735927) - (xy 129.92609 122.735914) (xy 129.838489 122.604811) (xy 129.838486 122.604807) (xy 129.726992 122.493313) - (xy 129.726988 122.49331) (xy 129.595885 122.405709) (xy 129.595872 122.405702) (xy 129.450201 122.345364) - (xy 129.450189 122.345361) (xy 129.295545 122.3146) (xy 129.295542 122.3146) (xy 129.137858 122.3146) - (xy 129.137855 122.3146) (xy 128.98321 122.345361) (xy 128.983198 122.345364) (xy 128.837527 122.405702) - (xy 128.837514 122.405709) (xy 128.706411 122.49331) (xy 128.706407 122.493313) (xy 128.594913 122.604807) - (xy 128.59491 122.604811) (xy 128.507309 122.735914) (xy 128.507302 122.735927) (xy 128.446964 122.881598) - (xy 128.446961 122.88161) (xy 128.4162 123.036253) (xy 124.242467 123.036253) (xy 124.251557 123.018412) - (xy 124.317246 122.816243) (xy 124.3505 122.606287) (xy 124.3505 122.393713) (xy 124.317246 122.183757) - (xy 124.251557 121.981588) (xy 124.155051 121.792184) (xy 124.155049 121.792181) (xy 124.155048 121.792179) - (xy 124.030109 121.620213) (xy 123.88105 121.471154) (xy 126.4995 121.471154) (xy 126.4995 121.628847) - (xy 126.530261 121.78349) (xy 126.530264 121.783502) (xy 126.590602 121.929173) (xy 126.590609 121.929186) - (xy 126.67821 122.060289) (xy 126.678213 122.060293) (xy 126.789707 122.171787) (xy 126.789711 122.17179) - (xy 126.920814 122.259391) (xy 126.920827 122.259398) (xy 127.066498 122.319736) (xy 127.066503 122.319738) - (xy 127.195318 122.345361) (xy 127.221153 122.3505) (xy 127.221156 122.350501) (xy 127.221158 122.350501) - (xy 127.378844 122.350501) (xy 127.378845 122.3505) (xy 127.533497 122.319738) (xy 127.679179 122.259395) - (xy 127.810289 122.17179) (xy 127.921789 122.06029) (xy 128.009394 121.92918) (xy 128.069737 121.783498) - (xy 128.1005 121.628843) (xy 128.1005 121.623653) (xy 133.8495 121.623653) (xy 133.8495 121.781346) - (xy 133.880261 121.935989) (xy 133.880264 121.936001) (xy 133.940602 122.081672) (xy 133.940609 122.081685) - (xy 134.02821 122.212788) (xy 134.028213 122.212792) (xy 134.139707 122.324286) (xy 134.139711 122.324289) - (xy 134.270814 122.41189) (xy 134.270827 122.411897) (xy 134.416498 122.472235) (xy 134.416503 122.472237) - (xy 134.556755 122.500135) (xy 134.571153 122.502999) (xy 134.571156 122.503) (xy 134.571158 122.503) - (xy 134.728844 122.503) (xy 134.728845 122.502999) (xy 134.883497 122.472237) (xy 135.029179 122.411894) - (xy 135.160289 122.324289) (xy 135.243973 122.240604) (xy 135.305294 122.20712) (xy 135.374985 122.212104) - (xy 135.37907 122.213711) (xy 135.516503 122.270637) (xy 135.671153 122.301399) (xy 135.671156 122.3014) - (xy 135.671158 122.3014) (xy 135.828844 122.3014) (xy 135.828845 122.301399) (xy 135.983497 122.270637) - (xy 136.123148 122.212792) (xy 136.129172 122.210297) (xy 136.129172 122.210296) (xy 136.129179 122.210294) - (xy 136.260289 122.122689) (xy 136.371789 122.011189) (xy 136.459394 121.880079) (xy 136.496684 121.790053) - (xy 138.6495 121.790053) (xy 138.6495 121.947746) (xy 138.680261 122.102389) (xy 138.680264 122.102401) - (xy 138.740602 122.248072) (xy 138.740609 122.248085) (xy 138.82821 122.379188) (xy 138.828213 122.379192) - (xy 138.939707 122.490686) (xy 138.939711 122.490689) (xy 139.070814 122.57829) (xy 139.070827 122.578297) - (xy 139.216498 122.638635) (xy 139.216503 122.638637) (xy 139.371153 122.669399) (xy 139.371156 122.6694) - (xy 139.371158 122.6694) (xy 139.528844 122.6694) (xy 139.528845 122.669399) (xy 139.683497 122.638637) - (xy 139.796166 122.591967) (xy 139.829172 122.578297) (xy 139.829172 122.578296) (xy 139.829179 122.578294) - (xy 139.960289 122.490689) (xy 140.025995 122.424983) (xy 144.0995 122.424983) (xy 144.0995 123.775001) - (xy 144.099501 123.775018) (xy 144.11 123.877796) (xy 144.110001 123.877799) (xy 144.142045 123.9745) - (xy 144.165186 124.044334) (xy 144.257288 124.193656) (xy 144.381344 124.317712) (xy 144.530666 124.409814) + (xy 145.748444 126.481585) (xy 145.682753 126.68376) (xy 145.6495 126.893713) (xy 133.049673 126.893713) + (xy 133.049114 126.892034) (xy 133.049035 126.887611) (xy 133.049035 126.84116) (xy 133.049034 126.841158) + (xy 133.018273 126.686515) (xy 133.018272 126.686508) (xy 132.980932 126.59636) (xy 132.957932 126.540832) + (xy 132.957925 126.540819) (xy 132.870324 126.409716) (xy 132.870321 126.409712) (xy 132.758827 126.298218) + (xy 132.758823 126.298215) (xy 132.62772 126.210614) (xy 132.627707 126.210607) (xy 132.482036 126.150269) + (xy 132.482024 126.150266) (xy 132.32738 126.119505) (xy 132.327377 126.119505) (xy 132.169693 126.119505) + (xy 132.16969 126.119505) (xy 132.015045 126.150266) (xy 132.015033 126.150269) (xy 131.869362 126.210607) + (xy 131.869349 126.210614) (xy 131.738246 126.298215) (xy 131.738242 126.298218) (xy 131.626748 126.409712) + (xy 131.626745 126.409716) (xy 131.539144 126.540819) (xy 131.539137 126.540832) (xy 131.478799 126.686503) + (xy 131.478796 126.686515) (xy 131.448035 126.841158) (xy 120.2505 126.841158) (xy 120.2505 126.663399) + (xy 120.270185 126.59636) (xy 120.322989 126.550605) (xy 120.392147 126.540661) (xy 120.398692 126.541782) + (xy 120.521155 126.566142) (xy 120.521158 126.566142) (xy 120.678844 126.566142) (xy 120.678845 126.566141) + (xy 120.833497 126.535379) (xy 120.979179 126.475036) (xy 121.110289 126.387431) (xy 121.221789 126.275931) + (xy 121.309394 126.144821) (xy 121.369737 125.999139) (xy 121.4005 125.844484) (xy 121.4005 125.705047) + (xy 121.420185 125.638008) (xy 121.472989 125.592253) (xy 121.476986 125.590512) (xy 121.479179 125.589604) + (xy 121.610289 125.501999) (xy 121.61151 125.500777) (xy 121.612306 125.500342) (xy 121.614993 125.498138) + (xy 121.615411 125.498647) (xy 121.672828 125.467288) (xy 121.723389 125.466835) (xy 121.795896 125.481258) + (xy 121.795899 125.481258) (xy 121.953585 125.481258) (xy 121.953586 125.481257) (xy 122.108238 125.450495) + (xy 122.25392 125.390152) (xy 122.38503 125.302547) (xy 122.49653 125.191047) (xy 122.584135 125.059937) + (xy 122.644478 124.914255) (xy 122.657557 124.848499) (xy 122.66379 124.817169) (xy 124.2795 124.817169) + (xy 124.2795 124.974862) (xy 124.310261 125.129505) (xy 124.310264 125.129517) (xy 124.370602 125.275188) + (xy 124.370609 125.275201) (xy 124.45821 125.406304) (xy 124.458213 125.406308) (xy 124.569707 125.517802) + (xy 124.569711 125.517805) (xy 124.700814 125.605406) (xy 124.700827 125.605413) (xy 124.807264 125.6495) + (xy 124.846503 125.665753) (xy 124.952313 125.6868) (xy 125.001153 125.696515) (xy 125.001156 125.696516) + (xy 125.001158 125.696516) (xy 125.158844 125.696516) (xy 125.158845 125.696515) (xy 125.313497 125.665753) + (xy 125.426166 125.619083) (xy 125.459172 125.605413) (xy 125.459172 125.605412) (xy 125.459179 125.60541) + (xy 125.590289 125.517805) (xy 125.701789 125.406305) (xy 125.789394 125.275195) (xy 125.849737 125.129513) + (xy 125.8805 124.974858) (xy 125.8805 124.817174) (xy 125.8805 124.817171) (xy 125.880499 124.817169) + (xy 125.869048 124.7596) (xy 125.849737 124.662519) (xy 125.834513 124.625764) (xy 125.789397 124.516843) + (xy 125.78939 124.51683) (xy 125.701789 124.385727) (xy 125.701786 124.385723) (xy 125.624713 124.30865) + (xy 125.591228 124.247327) (xy 125.596212 124.177635) (xy 125.638084 124.121702) (xy 125.703548 124.097285) + (xy 125.759847 124.106408) (xy 125.768701 124.110076) (xy 125.914458 124.139069) (xy 125.923351 124.140838) + (xy 125.923354 124.140839) (xy 125.923356 124.140839) (xy 126.081042 124.140839) (xy 126.081043 124.140838) + (xy 126.235695 124.110076) (xy 126.356098 124.060204) (xy 126.38137 124.049736) (xy 126.38137 124.049735) + (xy 126.381377 124.049733) (xy 126.512487 123.962128) (xy 126.623987 123.850628) (xy 126.711592 123.719518) + (xy 126.752336 123.621153) (xy 128.3995 123.621153) (xy 128.3995 123.778846) (xy 128.430261 123.933489) + (xy 128.430264 123.933501) (xy 128.490602 124.079172) (xy 128.490609 124.079185) (xy 128.57821 124.210288) + (xy 128.578213 124.210292) (xy 128.689707 124.321786) (xy 128.689711 124.321789) (xy 128.820814 124.40939) + (xy 128.820827 124.409397) (xy 128.955062 124.464998) (xy 128.966503 124.469737) (xy 129.121153 124.500499) + (xy 129.121156 124.5005) (xy 129.121158 124.5005) (xy 129.278844 124.5005) (xy 129.278845 124.500499) + (xy 129.433497 124.469737) (xy 129.579179 124.409394) (xy 129.710289 124.321789) (xy 129.821789 124.210289) + (xy 129.837603 124.186622) (xy 129.862242 124.149748) (xy 129.862242 124.149747) (xy 129.880981 124.121702) + (xy 129.909394 124.079179) (xy 129.921593 124.049729) (xy 129.954054 123.97136) (xy 129.969737 123.933497) + (xy 130.0005 123.778842) (xy 130.0005 123.621158) (xy 130.0005 123.621155) (xy 130.000499 123.621153) + (xy 129.991087 123.573836) (xy 129.969737 123.466503) (xy 129.930388 123.371504) (xy 131.68 123.371504) + (xy 131.68 123.77) (xy 132.38 123.77) (xy 132.38 124.27) (xy 131.68 124.27) (xy 131.68 124.668495) + (xy 131.718427 124.861681) (xy 131.71843 124.861693) (xy 131.793807 125.043671) (xy 131.793814 125.043684) + (xy 131.903248 125.207462) (xy 131.903251 125.207466) (xy 132.042533 125.346748) (xy 132.042537 125.346751) + (xy 132.206315 125.456185) (xy 132.206328 125.456192) (xy 132.388308 125.531569) (xy 132.43 125.539862) + (xy 132.43 124.736988) (xy 132.43994 124.754205) (xy 132.495795 124.81006) (xy 132.564204 124.849556) + (xy 132.640504 124.87) (xy 132.719496 124.87) (xy 132.795796 124.849556) (xy 132.864205 124.81006) + (xy 132.92006 124.754205) (xy 132.93 124.736988) (xy 132.93 125.539862) (xy 132.97169 125.531569) + (xy 132.971692 125.531569) (xy 133.153671 125.456192) (xy 133.153684 125.456185) (xy 133.317462 125.346751) + (xy 133.317466 125.346748) (xy 133.456748 125.207466) (xy 133.456751 125.207462) (xy 133.569574 125.038613) + (xy 133.571007 125.03957) (xy 133.614198 124.99558) (xy 133.682332 124.980103) (xy 133.748018 125.003919) + (xy 133.750089 125.005697) (xy 133.750189 125.005568) (xy 133.75663 125.01051) (xy 133.756635 125.010515) + (xy 133.887865 125.086281) (xy 134.034234 125.1255) (xy 134.034236 125.1255) (xy 134.185764 125.1255) + (xy 134.185766 125.1255) (xy 134.332135 125.086281) (xy 134.463365 125.010515) (xy 134.570515 124.903365) + (xy 134.61798 124.821153) (xy 136.1995 124.821153) (xy 136.1995 124.978846) (xy 136.230261 125.133489) + (xy 136.230264 125.133501) (xy 136.290602 125.279172) (xy 136.290609 125.279185) (xy 136.37821 125.410288) + (xy 136.378213 125.410292) (xy 136.489707 125.521786) (xy 136.489711 125.521789) (xy 136.620814 125.60939) + (xy 136.620827 125.609397) (xy 136.756887 125.665754) (xy 136.766503 125.669737) (xy 136.901124 125.696515) + (xy 136.921153 125.700499) (xy 136.921156 125.7005) (xy 136.921158 125.7005) (xy 137.078844 125.7005) + (xy 137.078845 125.700499) (xy 137.233497 125.669737) (xy 137.379179 125.609394) (xy 137.510289 125.521789) + (xy 137.621789 125.410289) (xy 137.709394 125.279179) (xy 137.769737 125.133497) (xy 137.8005 124.978842) + (xy 137.8005 124.821158) (xy 137.8005 124.821155) (xy 137.800499 124.821153) (xy 137.787182 124.754205) + (xy 137.769737 124.666503) (xy 137.76154 124.646713) (xy 137.709397 124.520827) (xy 137.70939 124.520814) + (xy 137.678266 124.474234) (xy 139.3145 124.474234) (xy 139.3145 124.625766) (xy 139.325949 124.668495) + (xy 139.353719 124.772136) (xy 139.391602 124.83775) (xy 139.429485 124.903365) (xy 139.536635 125.010515) + (xy 139.667865 125.086281) (xy 139.814234 125.1255) (xy 139.814236 125.1255) (xy 139.965764 125.1255) + (xy 139.965766 125.1255) (xy 140.112135 125.086281) (xy 140.243365 125.010515) (xy 140.243372 125.010507) + (xy 140.249811 125.005568) (xy 140.252044 125.008478) (xy 140.298258 124.982865) (xy 140.36798 124.987411) + (xy 140.424176 125.02893) (xy 140.430394 125.038634) (xy 140.430426 125.038613) (xy 140.543248 125.207462) + (xy 140.543251 125.207466) (xy 140.682533 125.346748) (xy 140.682537 125.346751) (xy 140.846315 125.456185) + (xy 140.846328 125.456192) (xy 141.028308 125.531569) (xy 141.07 125.539862) (xy 141.07 124.736988) + (xy 141.07994 124.754205) (xy 141.135795 124.81006) (xy 141.204204 124.849556) (xy 141.280504 124.87) + (xy 141.359496 124.87) (xy 141.435796 124.849556) (xy 141.501382 124.811689) (xy 141.4995 124.821153) + (xy 141.4995 124.978846) (xy 141.530261 125.133489) (xy 141.530264 125.133501) (xy 141.560561 125.206644) + (xy 141.57 125.254096) (xy 141.57 125.539862) (xy 141.611689 125.53157) (xy 141.669386 125.507671) + (xy 141.738856 125.500202) (xy 141.785731 125.51913) (xy 141.920814 125.60939) (xy 141.920827 125.609397) + (xy 142.056887 125.665754) (xy 142.066503 125.669737) (xy 142.201124 125.696515) (xy 142.221153 125.700499) + (xy 142.221156 125.7005) (xy 142.221158 125.7005) (xy 142.378844 125.7005) (xy 142.378845 125.700499) + (xy 142.533497 125.669737) (xy 142.679179 125.609394) (xy 142.810289 125.521789) (xy 142.921789 125.410289) + (xy 143.009394 125.279179) (xy 143.069737 125.133497) (xy 143.1005 124.978842) (xy 143.1005 124.821158) + (xy 143.1005 124.821155) (xy 143.100499 124.821153) (xy 143.087182 124.754205) (xy 143.069737 124.666503) + (xy 143.06154 124.646713) (xy 143.009397 124.520827) (xy 143.00939 124.520814) (xy 142.921789 124.389711) + (xy 142.921786 124.389707) (xy 142.810292 124.278213) (xy 142.810288 124.27821) (xy 142.679185 124.190609) + (xy 142.679172 124.190602) (xy 142.533501 124.130264) (xy 142.533489 124.130261) (xy 142.378845 124.0995) + (xy 142.378842 124.0995) (xy 142.221158 124.0995) (xy 142.221155 124.0995) (xy 142.06651 124.130261) + (xy 142.066498 124.130264) (xy 141.920827 124.190602) (xy 141.920815 124.190609) (xy 141.833276 124.249102) + (xy 141.766599 124.26998) (xy 141.764385 124.27) (xy 141.62 124.27) (xy 141.62 123.77) (xy 142.32 123.77) + (xy 142.32 123.371508) (xy 142.319999 123.371504) (xy 142.281572 123.178318) (xy 142.281569 123.178306) + (xy 142.206192 122.996328) (xy 142.206185 122.996315) (xy 142.096751 122.832537) (xy 142.096748 122.832533) + (xy 141.957466 122.693251) (xy 141.957462 122.693248) (xy 141.793684 122.583814) (xy 141.793671 122.583807) + (xy 141.679206 122.536395) (xy 141.611691 122.508429) (xy 141.611683 122.508427) (xy 141.57 122.500135) + (xy 141.57 123.303011) (xy 141.56006 123.285795) (xy 141.504205 123.22994) (xy 141.435796 123.190444) + (xy 141.359496 123.17) (xy 141.280504 123.17) (xy 141.204204 123.190444) (xy 141.135795 123.22994) + (xy 141.07994 123.285795) (xy 141.07 123.303011) (xy 141.07 122.500136) (xy 141.069999 122.500135) + (xy 141.028316 122.508427) (xy 141.028308 122.508429) (xy 140.846328 122.583807) (xy 140.846315 122.583814) + (xy 140.682537 122.693248) (xy 140.682533 122.693251) (xy 140.543251 122.832533) (xy 140.543248 122.832537) + (xy 140.433814 122.996315) (xy 140.433807 122.996328) (xy 140.35843 123.178306) (xy 140.358427 123.178318) + (xy 140.32 123.371504) (xy 140.32 123.77) (xy 141.02 123.77) (xy 141.02 124.27) (xy 140.464464 124.27) + (xy 140.397425 124.250315) (xy 140.357077 124.208) (xy 140.350517 124.196638) (xy 140.350513 124.196633) + (xy 140.243367 124.089487) (xy 140.243365 124.089485) (xy 140.165162 124.044334) (xy 140.112136 124.013719) + (xy 140.019982 123.989027) (xy 139.965766 123.9745) (xy 139.814234 123.9745) (xy 139.667863 124.013719) + (xy 139.536635 124.089485) (xy 139.536632 124.089487) (xy 139.429487 124.196632) (xy 139.429485 124.196635) + (xy 139.353719 124.327863) (xy 139.316975 124.464998) (xy 139.3145 124.474234) (xy 137.678266 124.474234) + (xy 137.621789 124.389711) (xy 137.621786 124.389707) (xy 137.510292 124.278213) (xy 137.510288 124.27821) + (xy 137.379185 124.190609) (xy 137.379172 124.190602) (xy 137.233501 124.130264) (xy 137.233489 124.130261) + (xy 137.078845 124.0995) (xy 137.078842 124.0995) (xy 136.921158 124.0995) (xy 136.921155 124.0995) + (xy 136.76651 124.130261) (xy 136.766498 124.130264) (xy 136.620827 124.190602) (xy 136.620814 124.190609) + (xy 136.489711 124.27821) (xy 136.489707 124.278213) (xy 136.378213 124.389707) (xy 136.37821 124.389711) + (xy 136.290609 124.520814) (xy 136.290602 124.520827) (xy 136.230264 124.666498) (xy 136.230261 124.66651) + (xy 136.1995 124.821153) (xy 134.61798 124.821153) (xy 134.646281 124.772135) (xy 134.6855 124.625766) + (xy 134.6855 124.474234) (xy 134.646281 124.327865) (xy 134.570515 124.196635) (xy 134.463365 124.089485) + (xy 134.385162 124.044334) (xy 134.332136 124.013719) (xy 134.239982 123.989027) (xy 134.185766 123.9745) + (xy 134.034234 123.9745) (xy 133.887863 124.013719) (xy 133.756635 124.089485) (xy 133.756632 124.089487) + (xy 133.649486 124.196633) (xy 133.649482 124.196638) (xy 133.642923 124.208) (xy 133.592356 124.256216) + (xy 133.535536 124.27) (xy 132.98 124.27) (xy 132.98 123.77) (xy 133.68 123.77) (xy 133.68 123.371508) + (xy 133.679999 123.371504) (xy 133.641572 123.178318) (xy 133.641569 123.178306) (xy 133.566192 122.996328) + (xy 133.566185 122.996315) (xy 133.456751 122.832537) (xy 133.456748 122.832533) (xy 133.317466 122.693251) + (xy 133.317462 122.693248) (xy 133.153684 122.583814) (xy 133.153671 122.583807) (xy 132.971691 122.508429) + (xy 132.971683 122.508427) (xy 132.93 122.500135) (xy 132.93 123.303011) (xy 132.92006 123.285795) + (xy 132.864205 123.22994) (xy 132.795796 123.190444) (xy 132.719496 123.17) (xy 132.640504 123.17) + (xy 132.564204 123.190444) (xy 132.495795 123.22994) (xy 132.43994 123.285795) (xy 132.43 123.303011) + (xy 132.43 122.500136) (xy 132.429999 122.500135) (xy 132.388316 122.508427) (xy 132.388308 122.508429) + (xy 132.206328 122.583807) (xy 132.206315 122.583814) (xy 132.042537 122.693248) (xy 132.042533 122.693251) + (xy 131.903251 122.832533) (xy 131.903248 122.832537) (xy 131.793814 122.996315) (xy 131.793807 122.996328) + (xy 131.71843 123.178306) (xy 131.718427 123.178318) (xy 131.68 123.371504) (xy 129.930388 123.371504) + (xy 129.913302 123.330255) (xy 129.909395 123.320823) (xy 129.90939 123.320814) (xy 129.821789 123.189711) + (xy 129.821786 123.189707) (xy 129.710292 123.078213) (xy 129.710288 123.07821) (xy 129.579185 122.990609) + (xy 129.579172 122.990602) (xy 129.433501 122.930264) (xy 129.433489 122.930261) (xy 129.278845 122.8995) + (xy 129.278842 122.8995) (xy 129.121158 122.8995) (xy 129.121155 122.8995) (xy 128.96651 122.930261) + (xy 128.966498 122.930264) (xy 128.820827 122.990602) (xy 128.820814 122.990609) (xy 128.689711 123.07821) + (xy 128.689707 123.078213) (xy 128.578213 123.189707) (xy 128.57821 123.189711) (xy 128.490609 123.320814) + (xy 128.490602 123.320827) (xy 128.430264 123.466498) (xy 128.430261 123.46651) (xy 128.3995 123.621153) + (xy 126.752336 123.621153) (xy 126.771935 123.573836) (xy 126.802698 123.419181) (xy 126.802698 123.261497) + (xy 126.802698 123.261494) (xy 126.802697 123.261492) (xy 126.79202 123.207816) (xy 126.771935 123.106842) + (xy 126.760075 123.07821) (xy 126.711595 122.961166) (xy 126.711588 122.961153) (xy 126.623987 122.83005) + (xy 126.623984 122.830046) (xy 126.51249 122.718552) (xy 126.512486 122.718549) (xy 126.381383 122.630948) + (xy 126.38137 122.630941) (xy 126.235699 122.570603) (xy 126.235687 122.5706) (xy 126.081043 122.539839) + (xy 126.08104 122.539839) (xy 125.923356 122.539839) (xy 125.923353 122.539839) (xy 125.768708 122.5706) + (xy 125.768696 122.570603) (xy 125.623025 122.630941) (xy 125.623012 122.630948) (xy 125.491909 122.718549) + (xy 125.491905 122.718552) (xy 125.380411 122.830046) (xy 125.380408 122.83005) (xy 125.292807 122.961153) + (xy 125.2928 122.961166) (xy 125.232462 123.106837) (xy 125.232459 123.106849) (xy 125.201698 123.261492) + (xy 125.201698 123.419185) (xy 125.232459 123.573828) (xy 125.232462 123.57384) (xy 125.2928 123.719511) + (xy 125.292807 123.719524) (xy 125.380408 123.850627) (xy 125.380411 123.850631) (xy 125.457484 123.927704) + (xy 125.490969 123.989027) (xy 125.485985 124.058719) (xy 125.444113 124.114652) (xy 125.378649 124.139069) + (xy 125.322352 124.129947) (xy 125.320114 124.12902) (xy 125.313497 124.126279) (xy 125.313493 124.126278) + (xy 125.313489 124.126277) (xy 125.158845 124.095516) (xy 125.158842 124.095516) (xy 125.001158 124.095516) + (xy 125.001155 124.095516) (xy 124.84651 124.126277) (xy 124.846498 124.12628) (xy 124.700827 124.186618) + (xy 124.700814 124.186625) (xy 124.569711 124.274226) (xy 124.569707 124.274229) (xy 124.458213 124.385723) + (xy 124.45821 124.385727) (xy 124.370609 124.51683) (xy 124.370602 124.516843) (xy 124.310264 124.662514) + (xy 124.310261 124.662526) (xy 124.2795 124.817169) (xy 122.66379 124.817169) (xy 122.669813 124.786891) + (xy 122.669813 124.78689) (xy 122.675241 124.759602) (xy 122.675241 124.601913) (xy 122.67524 124.601911) + (xy 122.65911 124.520821) (xy 122.644478 124.447261) (xy 122.628966 124.409812) (xy 122.584138 124.301585) + (xy 122.584131 124.301572) (xy 122.49653 124.170469) (xy 122.496527 124.170465) (xy 122.385033 124.058971) + (xy 122.385029 124.058968) (xy 122.253926 123.971367) (xy 122.253913 123.97136) (xy 122.108242 123.911022) + (xy 122.10823 123.911019) (xy 121.953586 123.880258) (xy 121.953583 123.880258) (xy 121.795899 123.880258) + (xy 121.795896 123.880258) (xy 121.641251 123.911019) (xy 121.641239 123.911022) (xy 121.495568 123.97136) + (xy 121.495555 123.971367) (xy 121.364455 124.058966) (xy 121.364446 124.058973) (xy 121.363216 124.060204) + (xy 121.362414 124.060641) (xy 121.359748 124.06283) (xy 121.359332 124.062324) (xy 121.30189 124.093684) + (xy 121.251353 124.094133) (xy 121.226188 124.089127) (xy 121.178842 124.07971) (xy 121.021158 124.07971) + (xy 121.021155 124.07971) (xy 120.86651 124.110471) (xy 120.866498 124.110474) (xy 120.720827 124.170812) + (xy 120.720814 124.170819) (xy 120.589711 124.25842) (xy 120.589707 124.258423) (xy 120.478213 124.369917) + (xy 120.478206 124.369926) (xy 120.477597 124.370838) (xy 120.477155 124.371207) (xy 120.474347 124.374629) + (xy 120.473697 124.374096) (xy 120.423982 124.415639) (xy 120.354656 124.424342) (xy 120.291631 124.394183) + (xy 120.254916 124.334737) (xy 120.2505 124.30194) (xy 120.2505 122.393713) (xy 121.6495 122.393713) + (xy 121.6495 122.606287) (xy 121.682754 122.816243) (xy 121.741267 122.996328) (xy 121.748444 123.018414) + (xy 121.844951 123.20782) (xy 121.96989 123.379786) (xy 122.120213 123.530109) (xy 122.292179 123.655048) + (xy 122.292181 123.655049) (xy 122.292184 123.655051) (xy 122.481588 123.751557) (xy 122.683757 123.817246) + (xy 122.893713 123.8505) (xy 122.893714 123.8505) (xy 123.106286 123.8505) (xy 123.106287 123.8505) + (xy 123.316243 123.817246) (xy 123.518412 123.751557) (xy 123.707816 123.655051) (xy 123.754473 123.621153) + (xy 123.879786 123.530109) (xy 123.879788 123.530106) (xy 123.879792 123.530104) (xy 124.030104 123.379792) + (xy 124.030106 123.379788) (xy 124.030109 123.379786) (xy 124.155048 123.20782) (xy 124.155047 123.20782) + (xy 124.155051 123.207816) (xy 124.251557 123.018412) (xy 124.317246 122.816243) (xy 124.3505 122.606287) + (xy 124.3505 122.424983) (xy 144.0995 122.424983) (xy 144.0995 123.775001) (xy 144.099501 123.775018) + (xy 144.11 123.877796) (xy 144.110001 123.877799) (xy 144.165185 124.044331) (xy 144.165187 124.044336) + (xy 144.186682 124.079185) (xy 144.257288 124.193656) (xy 144.381344 124.317712) (xy 144.530666 124.409814) (xy 144.697203 124.464999) (xy 144.799991 124.4755) (xy 145.600008 124.475499) (xy 145.600016 124.475498) - (xy 145.600019 124.475498) (xy 145.656302 124.469748) (xy 145.702797 124.464999) (xy 145.869334 124.409814) + (xy 145.600019 124.475498) (xy 145.656434 124.469735) (xy 145.702797 124.464999) (xy 145.869334 124.409814) (xy 146.018656 124.317712) (xy 146.142712 124.193656) (xy 146.182581 124.129016) (xy 146.234525 124.082294) (xy 146.303488 124.071071) (xy 146.36757 124.098914) (xy 146.375799 124.106434) (xy 146.483397 124.214032) (xy 146.623475 124.315804) (xy 146.777744 124.394408) (xy 146.942415 124.447914) (xy 146.942414 124.447914) @@ -38436,804 +38818,960 @@ (xy 146.623475 121.884195) (xy 146.483401 121.985964) (xy 146.375799 122.093566) (xy 146.314476 122.12705) (xy 146.244784 122.122066) (xy 146.188851 122.080194) (xy 146.182585 122.070988) (xy 146.142712 122.006344) (xy 146.018656 121.882288) (xy 145.89431 121.805591) (xy 145.869336 121.790187) (xy 145.869331 121.790185) - (xy 145.849127 121.78349) (xy 145.702797 121.735001) (xy 145.702795 121.735) (xy 145.60001 121.7245) + (xy 145.867862 121.789698) (xy 145.702797 121.735001) (xy 145.702795 121.735) (xy 145.60001 121.7245) (xy 144.799998 121.7245) (xy 144.79998 121.724501) (xy 144.697203 121.735) (xy 144.6972 121.735001) (xy 144.530668 121.790185) (xy 144.530663 121.790187) (xy 144.381342 121.882289) (xy 144.257289 122.006342) - (xy 144.165187 122.155663) (xy 144.165185 122.155668) (xy 144.148136 122.20712) (xy 144.110001 122.322203) - (xy 144.110001 122.322204) (xy 144.11 122.322204) (xy 144.0995 122.424983) (xy 140.025995 122.424983) - (xy 140.071789 122.379189) (xy 140.159394 122.248079) (xy 140.219737 122.102397) (xy 140.2505 121.947742) - (xy 140.2505 121.790058) (xy 140.2505 121.790055) (xy 140.250499 121.790053) (xy 140.23746 121.724501) - (xy 140.219737 121.635403) (xy 140.219735 121.635398) (xy 140.159397 121.489727) (xy 140.15939 121.489714) - (xy 140.071789 121.358611) (xy 140.071786 121.358607) (xy 139.960292 121.247113) (xy 139.960288 121.24711) - (xy 139.829185 121.159509) (xy 139.829172 121.159502) (xy 139.683501 121.099164) (xy 139.683489 121.099161) - (xy 139.528845 121.0684) (xy 139.528842 121.0684) (xy 139.371158 121.0684) (xy 139.371155 121.0684) - (xy 139.21651 121.099161) (xy 139.216498 121.099164) (xy 139.070827 121.159502) (xy 139.070814 121.159509) - (xy 138.939711 121.24711) (xy 138.939707 121.247113) (xy 138.828213 121.358607) (xy 138.82821 121.358611) - (xy 138.740609 121.489714) (xy 138.740602 121.489727) (xy 138.680264 121.635398) (xy 138.680261 121.63541) - (xy 138.6495 121.790053) (xy 136.496684 121.790053) (xy 136.519737 121.734397) (xy 136.5505 121.579742) - (xy 136.5505 121.422058) (xy 136.5505 121.422055) (xy 136.550499 121.422053) (xy 136.519737 121.267403) - (xy 136.511332 121.247111) (xy 136.459397 121.121727) (xy 136.45939 121.121714) (xy 136.371789 120.990611) - (xy 136.371786 120.990607) (xy 136.260292 120.879113) (xy 136.260288 120.87911) (xy 136.129185 120.791509) - (xy 136.129172 120.791502) (xy 135.983501 120.731164) (xy 135.983489 120.731161) (xy 135.828845 120.7004) - (xy 135.828842 120.7004) (xy 135.671158 120.7004) (xy 135.671155 120.7004) (xy 135.51651 120.731161) - (xy 135.516498 120.731164) (xy 135.370827 120.791502) (xy 135.370814 120.791509) (xy 135.239711 120.87911) - (xy 135.239707 120.879113) (xy 135.156027 120.962794) (xy 135.094704 120.996279) (xy 135.025012 120.991295) - (xy 135.020894 120.989674) (xy 134.883501 120.932764) (xy 134.883489 120.932761) (xy 134.728845 120.902) - (xy 134.728842 120.902) (xy 134.571158 120.902) (xy 134.571155 120.902) (xy 134.41651 120.932761) - (xy 134.416498 120.932764) (xy 134.270827 120.993102) (xy 134.270814 120.993109) (xy 134.139711 121.08071) - (xy 134.139707 121.080713) (xy 134.028213 121.192207) (xy 134.02821 121.192211) (xy 133.940609 121.323314) - (xy 133.940602 121.323327) (xy 133.880264 121.468998) (xy 133.880261 121.46901) (xy 133.8495 121.623653) - (xy 128.1005 121.623653) (xy 128.1005 121.471159) (xy 128.1005 121.471156) (xy 128.100499 121.471154) - (xy 128.090733 121.422058) (xy 128.069737 121.316504) (xy 128.041546 121.248444) (xy 128.009397 121.170828) - (xy 128.00939 121.170815) (xy 127.921789 121.039712) (xy 127.921786 121.039708) (xy 127.810292 120.928214) - (xy 127.810288 120.928211) (xy 127.679185 120.84061) (xy 127.679172 120.840603) (xy 127.533501 120.780265) - (xy 127.533489 120.780262) (xy 127.378845 120.749501) (xy 127.378842 120.749501) (xy 127.221158 120.749501) - (xy 127.221155 120.749501) (xy 127.06651 120.780262) (xy 127.066498 120.780265) (xy 126.920827 120.840603) - (xy 126.920814 120.84061) (xy 126.789711 120.928211) (xy 126.789707 120.928214) (xy 126.678213 121.039708) - (xy 126.67821 121.039712) (xy 126.590609 121.170815) (xy 126.590602 121.170828) (xy 126.530264 121.316499) - (xy 126.530261 121.316511) (xy 126.4995 121.471154) (xy 123.88105 121.471154) (xy 123.879786 121.46989) + (xy 144.165187 122.155663) (xy 144.165185 122.155668) (xy 144.137349 122.23967) (xy 144.110001 122.322203) + (xy 144.110001 122.322204) (xy 144.11 122.322204) (xy 144.0995 122.424983) (xy 124.3505 122.424983) + (xy 124.3505 122.393713) (xy 124.317246 122.183757) (xy 124.251557 121.981588) (xy 124.155051 121.792184) + (xy 124.155049 121.792181) (xy 124.155048 121.792179) (xy 124.030109 121.620213) (xy 123.879786 121.46989) (xy 123.70782 121.344951) (xy 123.518414 121.248444) (xy 123.518413 121.248443) (xy 123.518412 121.248443) (xy 123.316243 121.182754) (xy 123.316241 121.182753) (xy 123.31624 121.182753) (xy 123.154957 121.157208) (xy 123.106287 121.1495) (xy 122.893713 121.1495) (xy 122.845042 121.157208) (xy 122.68376 121.182753) - (xy 122.683757 121.182754) (xy 122.485688 121.247111) (xy 122.481585 121.248444) (xy 122.292179 121.344951) - (xy 122.120213 121.46989) (xy 121.96989 121.620213) (xy 121.844951 121.792179) (xy 121.748444 121.981585) - (xy 121.682753 122.18376) (xy 121.661216 122.319739) (xy 121.6495 122.393713) (xy 120.2505 122.393713) - (xy 120.2505 119.368591) (xy 129.40854 119.368591) (xy 129.442112 119.391023) (xy 129.560401 119.44002) - (xy 129.560409 119.440022) (xy 129.685976 119.464999) (xy 129.68598 119.465) (xy 129.81402 119.465) - (xy 129.814023 119.464999) (xy 129.93959 119.440022) (xy 129.939594 119.440021) (xy 130.057891 119.39102) - (xy 130.057898 119.391016) (xy 130.091458 119.368591) (xy 130.091459 119.36859) (xy 129.750001 119.027132) - (xy 129.75 119.027132) (xy 129.40854 119.368591) (xy 120.2505 119.368591) (xy 120.2505 118.750976) - (xy 129.1 118.750976) (xy 129.1 118.879023) (xy 129.124977 119.00459) (xy 129.124979 119.004598) - (xy 129.173976 119.122886) (xy 129.173981 119.122896) (xy 129.196407 119.156458) (xy 129.196408 119.156458) - (xy 129.537868 118.815) (xy 129.537868 118.814999) (xy 129.517978 118.795109) (xy 129.65 118.795109) - (xy 129.65 118.834891) (xy 129.665224 118.871645) (xy 129.693355 118.899776) (xy 129.730109 118.915) - (xy 129.769891 118.915) (xy 129.806645 118.899776) (xy 129.834776 118.871645) (xy 129.85 118.834891) - (xy 129.85 118.814999) (xy 129.962132 118.814999) (xy 129.962132 118.815) (xy 130.30359 119.156459) - (xy 130.303591 119.156458) (xy 130.326016 119.122898) (xy 130.32602 119.122891) (xy 130.375021 119.004594) - (xy 130.375022 119.00459) (xy 130.399999 118.879023) (xy 130.4 118.87902) (xy 130.4 118.858553) - (xy 133.0101 118.858553) (xy 133.0101 119.016246) (xy 133.040861 119.170889) (xy 133.040864 119.170901) - (xy 133.101202 119.316572) (xy 133.101209 119.316585) (xy 133.18881 119.447688) (xy 133.188813 119.447692) - (xy 133.300307 119.559186) (xy 133.300311 119.559189) (xy 133.431414 119.64679) (xy 133.431427 119.646797) - (xy 133.577098 119.707135) (xy 133.577103 119.707137) (xy 133.731753 119.737899) (xy 133.731756 119.7379) - (xy 133.731758 119.7379) (xy 133.889444 119.7379) (xy 133.889445 119.737899) (xy 134.044097 119.707137) - (xy 134.189779 119.646794) (xy 134.320889 119.559189) (xy 134.432389 119.447689) (xy 134.519994 119.316579) - (xy 134.580337 119.170897) (xy 134.6111 119.016242) (xy 134.6111 118.858558) (xy 134.6111 118.858555) - (xy 134.611099 118.858553) (xy 134.602436 118.815) (xy 134.580337 118.703903) (xy 134.547821 118.625401) - (xy 134.519997 118.558227) (xy 134.51999 118.558214) (xy 134.432389 118.427111) (xy 134.432386 118.427107) - (xy 134.320892 118.315613) (xy 134.320888 118.31561) (xy 134.189785 118.228009) (xy 134.189772 118.228002) - (xy 134.044101 118.167664) (xy 134.044089 118.167661) (xy 133.889445 118.1369) (xy 133.889442 118.1369) - (xy 133.731758 118.1369) (xy 133.731755 118.1369) (xy 133.57711 118.167661) (xy 133.577098 118.167664) - (xy 133.431427 118.228002) (xy 133.431414 118.228009) (xy 133.300311 118.31561) (xy 133.300307 118.315613) - (xy 133.188813 118.427107) (xy 133.18881 118.427111) (xy 133.101209 118.558214) (xy 133.101202 118.558227) - (xy 133.040864 118.703898) (xy 133.040861 118.70391) (xy 133.0101 118.858553) (xy 130.4 118.858553) - (xy 130.4 118.75098) (xy 130.399999 118.750976) (xy 130.375022 118.625409) (xy 130.37502 118.625401) - (xy 130.326023 118.507112) (xy 130.303591 118.47354) (xy 129.962132 118.814999) (xy 129.85 118.814999) - (xy 129.85 118.795109) (xy 129.834776 118.758355) (xy 129.806645 118.730224) (xy 129.769891 118.715) - (xy 129.730109 118.715) (xy 129.693355 118.730224) (xy 129.665224 118.758355) (xy 129.65 118.795109) - (xy 129.517978 118.795109) (xy 129.196408 118.473539) (xy 129.196407 118.47354) (xy 129.173978 118.507109) - (xy 129.124979 118.625401) (xy 129.124977 118.625409) (xy 129.1 118.750976) (xy 120.2505 118.750976) - (xy 120.2505 117.511888) (xy 122.573765 117.511888) (xy 122.573765 117.669581) (xy 122.604526 117.824224) - (xy 122.604529 117.824236) (xy 122.664867 117.969907) (xy 122.664874 117.96992) (xy 122.752475 118.101023) - (xy 122.752478 118.101027) (xy 122.863972 118.212521) (xy 122.863976 118.212524) (xy 122.995079 118.300125) - (xy 122.995092 118.300132) (xy 123.140763 118.36047) (xy 123.140768 118.360472) (xy 123.295418 118.391234) - (xy 123.295421 118.391235) (xy 123.295423 118.391235) (xy 123.453109 118.391235) (xy 123.45311 118.391234) - (xy 123.607762 118.360472) (xy 123.717542 118.315) (xy 129.462132 118.315) (xy 129.75 118.602868) - (xy 130.037868 118.315) (xy 129.75 118.027132) (xy 129.462132 118.315) (xy 123.717542 118.315) (xy 123.753444 118.300129) - (xy 123.884554 118.212524) (xy 123.996054 118.101024) (xy 124.083659 117.969914) (xy 124.144002 117.824232) - (xy 124.158573 117.750976) (xy 129.1 117.750976) (xy 129.1 117.879023) (xy 129.124977 118.00459) - (xy 129.124979 118.004598) (xy 129.173976 118.122886) (xy 129.173981 118.122896) (xy 129.196407 118.156458) - (xy 129.196408 118.156458) (xy 129.537868 117.815) (xy 129.537868 117.814999) (xy 129.517978 117.795109) - (xy 129.65 117.795109) (xy 129.65 117.834891) (xy 129.665224 117.871645) (xy 129.693355 117.899776) - (xy 129.730109 117.915) (xy 129.769891 117.915) (xy 129.806645 117.899776) (xy 129.834776 117.871645) - (xy 129.85 117.834891) (xy 129.85 117.814999) (xy 129.962132 117.814999) (xy 129.962132 117.815) - (xy 130.30359 118.156459) (xy 130.303591 118.156458) (xy 130.326016 118.122898) (xy 130.32602 118.122891) - (xy 130.375021 118.004594) (xy 130.375022 118.00459) (xy 130.399999 117.879023) (xy 130.4 117.87902) - (xy 130.4 117.75098) (xy 130.399999 117.750976) (xy 130.375022 117.625409) (xy 130.37502 117.625401) - (xy 130.326023 117.507112) (xy 130.303591 117.47354) (xy 129.962132 117.814999) (xy 129.85 117.814999) - (xy 129.85 117.795109) (xy 129.834776 117.758355) (xy 129.806645 117.730224) (xy 129.769891 117.715) - (xy 129.730109 117.715) (xy 129.693355 117.730224) (xy 129.665224 117.758355) (xy 129.65 117.795109) - (xy 129.517978 117.795109) (xy 129.196408 117.473539) (xy 129.196407 117.47354) (xy 129.173978 117.507109) - (xy 129.124979 117.625401) (xy 129.124977 117.625409) (xy 129.1 117.750976) (xy 124.158573 117.750976) - (xy 124.165845 117.714416) (xy 124.19823 117.652507) (xy 124.234205 117.628007) (xy 124.233808 117.627264) - (xy 124.239167 117.624398) (xy 124.239179 117.624394) (xy 124.370289 117.536789) (xy 124.481789 117.425289) - (xy 124.569394 117.294179) (xy 124.577669 117.274201) (xy 124.582969 117.261408) (xy 129.408539 117.261408) - (xy 129.75 117.602868) (xy 129.750001 117.602868) (xy 130.091458 117.261408) (xy 130.091458 117.261407) - (xy 130.057896 117.238981) (xy 130.057886 117.238976) (xy 129.939598 117.189979) (xy 129.93959 117.189977) - (xy 129.814023 117.165) (xy 129.685976 117.165) (xy 129.560409 117.189977) (xy 129.560401 117.189979) - (xy 129.442109 117.238978) (xy 129.40854 117.261407) (xy 129.408539 117.261408) (xy 124.582969 117.261408) - (xy 124.583483 117.260166) (xy 124.583483 117.260164) (xy 124.592258 117.238981) (xy 124.629737 117.148497) - (xy 124.6605 116.993842) (xy 124.6605 116.836158) (xy 124.6605 116.836155) (xy 124.660499 116.836153) - (xy 124.629738 116.68151) (xy 124.629738 116.681508) (xy 124.629737 116.681503) (xy 124.629735 116.681498) - (xy 124.569397 116.535827) (xy 124.56939 116.535814) (xy 124.481789 116.404711) (xy 124.481786 116.404707) - (xy 124.370292 116.293213) (xy 124.370288 116.29321) (xy 124.239185 116.205609) (xy 124.239172 116.205602) - (xy 124.093501 116.145264) (xy 124.093489 116.145261) (xy 123.938845 116.1145) (xy 123.938842 116.1145) - (xy 123.781158 116.1145) (xy 123.781155 116.1145) (xy 123.62651 116.145261) (xy 123.626498 116.145264) - (xy 123.480827 116.205602) (xy 123.480814 116.205609) (xy 123.349711 116.29321) (xy 123.349707 116.293213) - (xy 123.238213 116.404707) (xy 123.23821 116.404711) (xy 123.150609 116.535814) (xy 123.150602 116.535827) - (xy 123.090264 116.681498) (xy 123.090261 116.681508) (xy 123.068419 116.791315) (xy 123.036034 116.853226) - (xy 123.000061 116.877732) (xy 123.000456 116.878471) (xy 122.995079 116.881344) (xy 122.863976 116.968945) - (xy 122.863972 116.968948) (xy 122.752478 117.080442) (xy 122.752475 117.080446) (xy 122.664874 117.211549) - (xy 122.664867 117.211562) (xy 122.604529 117.357233) (xy 122.604526 117.357245) (xy 122.573765 117.511888) - (xy 120.2505 117.511888) (xy 120.2505 114.70154) (xy 145.5542 114.70154) (xy 145.5542 114.848459) - (xy 145.582858 114.992534) (xy 145.582861 114.992544) (xy 145.639078 115.128266) (xy 145.639083 115.128275) - (xy 145.720698 115.250419) (xy 145.720701 115.250423) (xy 145.824576 115.354298) (xy 145.82458 115.354301) - (xy 145.946724 115.435916) (xy 145.94673 115.435919) (xy 145.946731 115.43592) (xy 146.082458 115.49214) - (xy 146.22654 115.520799) (xy 146.226544 115.5208) (xy 146.226545 115.5208) (xy 146.373456 115.5208) - (xy 146.373457 115.520799) (xy 146.517542 115.49214) (xy 146.653269 115.43592) (xy 146.77542 115.354301) - (xy 146.879301 115.25042) (xy 146.96092 115.128269) (xy 147.01714 114.992542) (xy 147.0458 114.848455) - (xy 147.0458 114.701545) (xy 147.01714 114.557458) (xy 146.963574 114.428138) (xy 146.960921 114.421733) - (xy 146.960916 114.421724) (xy 146.879301 114.29958) (xy 146.879298 114.299576) (xy 146.775423 114.195701) - (xy 146.775419 114.195698) (xy 146.653275 114.114083) (xy 146.653266 114.114078) (xy 146.517544 114.057861) - (xy 146.517545 114.057861) (xy 146.517542 114.05786) (xy 146.517538 114.057859) (xy 146.517534 114.057858) - (xy 146.373459 114.0292) (xy 146.373455 114.0292) (xy 146.226545 114.0292) (xy 146.22654 114.0292) - (xy 146.082465 114.057858) (xy 146.082455 114.057861) (xy 145.946733 114.114078) (xy 145.946724 114.114083) - (xy 145.82458 114.195698) (xy 145.824576 114.195701) (xy 145.720701 114.299576) (xy 145.720698 114.29958) - (xy 145.639083 114.421724) (xy 145.639078 114.421733) (xy 145.582861 114.557455) (xy 145.582858 114.557465) - (xy 145.5542 114.70154) (xy 120.2505 114.70154) (xy 120.2505 113.579553) (xy 123.0995 113.579553) - (xy 123.0995 113.737246) (xy 123.130261 113.891889) (xy 123.130264 113.891901) (xy 123.190602 114.037572) - (xy 123.190609 114.037585) (xy 123.27821 114.168688) (xy 123.278213 114.168692) (xy 123.389707 114.280186) - (xy 123.389711 114.280189) (xy 123.520814 114.36779) (xy 123.520827 114.367797) (xy 123.651037 114.421731) - (xy 123.666503 114.428137) (xy 123.821153 114.458899) (xy 123.821156 114.4589) (xy 123.821158 114.4589) - (xy 123.978844 114.4589) (xy 123.978845 114.458899) (xy 124.133497 114.428137) (xy 124.279179 114.367794) - (xy 124.410289 114.280189) (xy 124.521789 114.168689) (xy 124.609394 114.037579) (xy 124.669737 113.891897) - (xy 124.7005 113.737242) (xy 124.7005 113.579558) (xy 124.7005 113.579555) (xy 124.700499 113.579553) - (xy 124.669738 113.42491) (xy 124.669737 113.424903) (xy 124.669735 113.424898) (xy 124.609397 113.279227) - (xy 124.60939 113.279214) (xy 124.521789 113.148111) (xy 124.521786 113.148107) (xy 124.410292 113.036613) - (xy 124.410288 113.03661) (xy 124.279185 112.949009) (xy 124.279172 112.949002) (xy 124.133501 112.888664) - (xy 124.133489 112.888661) (xy 123.978845 112.8579) (xy 123.978842 112.8579) (xy 123.821158 112.8579) - (xy 123.821155 112.8579) (xy 123.66651 112.888661) (xy 123.666498 112.888664) (xy 123.520827 112.949002) - (xy 123.520814 112.949009) (xy 123.389711 113.03661) (xy 123.389707 113.036613) (xy 123.278213 113.148107) - (xy 123.27821 113.148111) (xy 123.190609 113.279214) (xy 123.190602 113.279227) (xy 123.130264 113.424898) - (xy 123.130261 113.42491) (xy 123.0995 113.579553) (xy 120.2505 113.579553) (xy 120.2505 112.221153) - (xy 131.1495 112.221153) (xy 131.1495 112.378846) (xy 131.180261 112.533489) (xy 131.180264 112.533501) - (xy 131.240602 112.679172) (xy 131.240609 112.679185) (xy 131.32821 112.810288) (xy 131.328213 112.810292) - (xy 131.439707 112.921786) (xy 131.439711 112.921789) (xy 131.570814 113.00939) (xy 131.570827 113.009397) - (xy 131.716498 113.069735) (xy 131.716503 113.069737) (xy 131.871153 113.100499) (xy 131.871156 113.1005) - (xy 131.871158 113.1005) (xy 132.028844 113.1005) (xy 132.028845 113.100499) (xy 132.183497 113.069737) - (xy 132.329179 113.009394) (xy 132.460289 112.921789) (xy 132.571789 112.810289) (xy 132.659394 112.679179) - (xy 132.719737 112.533497) (xy 132.7505 112.378842) (xy 132.7505 112.221158) (xy 132.7505 112.221155) - (xy 132.750499 112.221153) (xy 132.719738 112.06651) (xy 132.719737 112.066503) (xy 132.719735 112.066498) - (xy 132.659397 111.920827) (xy 132.65939 111.920814) (xy 132.571789 111.789711) (xy 132.571786 111.789707) - (xy 132.460292 111.678213) (xy 132.460288 111.67821) (xy 132.329185 111.590609) (xy 132.329172 111.590602) - (xy 132.183501 111.530264) (xy 132.183489 111.530261) (xy 132.028845 111.4995) (xy 132.028842 111.4995) - (xy 131.871158 111.4995) (xy 131.871155 111.4995) (xy 131.71651 111.530261) (xy 131.716498 111.530264) - (xy 131.570827 111.590602) (xy 131.570814 111.590609) (xy 131.439711 111.67821) (xy 131.439707 111.678213) - (xy 131.328213 111.789707) (xy 131.32821 111.789711) (xy 131.240609 111.920814) (xy 131.240602 111.920827) - (xy 131.180264 112.066498) (xy 131.180261 112.06651) (xy 131.1495 112.221153) (xy 120.2505 112.221153) - (xy 120.2505 110.902753) (xy 140.3162 110.902753) (xy 140.3162 111.060446) (xy 140.346961 111.215089) - (xy 140.346964 111.215101) (xy 140.407302 111.360772) (xy 140.407309 111.360785) (xy 140.49491 111.491888) - (xy 140.494913 111.491892) (xy 140.606407 111.603386) (xy 140.606411 111.603389) (xy 140.737514 111.69099) - (xy 140.737527 111.690997) (xy 140.883198 111.751335) (xy 140.883203 111.751337) (xy 141.037853 111.782099) - (xy 141.037856 111.7821) (xy 141.037858 111.7821) (xy 141.195544 111.7821) (xy 141.195545 111.782099) - (xy 141.28828 111.763653) (xy 147.2717 111.763653) (xy 147.2717 111.921346) (xy 147.302461 112.075989) - (xy 147.302464 112.076001) (xy 147.362802 112.221672) (xy 147.362809 112.221685) (xy 147.45041 112.352788) - (xy 147.450413 112.352792) (xy 147.561907 112.464286) (xy 147.561911 112.464289) (xy 147.693014 112.55189) - (xy 147.693027 112.551897) (xy 147.838698 112.612235) (xy 147.838703 112.612237) (xy 147.993353 112.642999) - (xy 147.993356 112.643) (xy 147.993358 112.643) (xy 148.151044 112.643) (xy 148.151045 112.642999) - (xy 148.305697 112.612237) (xy 148.451379 112.551894) (xy 148.582489 112.464289) (xy 148.693989 112.352789) - (xy 148.781594 112.221679) (xy 148.841937 112.075997) (xy 148.8727 111.921342) (xy 148.8727 111.763658) - (xy 148.8727 111.763655) (xy 148.872699 111.763653) (xy 148.841938 111.60901) (xy 148.841937 111.609003) - (xy 148.834315 111.590602) (xy 148.781597 111.463327) (xy 148.78159 111.463314) (xy 148.693989 111.332211) - (xy 148.693986 111.332207) (xy 148.582492 111.220713) (xy 148.582488 111.22071) (xy 148.451385 111.133109) - (xy 148.451372 111.133102) (xy 148.305701 111.072764) (xy 148.305689 111.072761) (xy 148.151045 111.042) - (xy 148.151042 111.042) (xy 147.993358 111.042) (xy 147.993355 111.042) (xy 147.83871 111.072761) - (xy 147.838698 111.072764) (xy 147.693027 111.133102) (xy 147.693014 111.133109) (xy 147.561911 111.22071) - (xy 147.561907 111.220713) (xy 147.450413 111.332207) (xy 147.45041 111.332211) (xy 147.362809 111.463314) - (xy 147.362802 111.463327) (xy 147.302464 111.608998) (xy 147.302461 111.60901) (xy 147.2717 111.763653) - (xy 141.28828 111.763653) (xy 141.350197 111.751337) (xy 141.495879 111.690994) (xy 141.515012 111.67821) - (xy 141.550551 111.654464) (xy 141.589758 111.628265) (xy 141.626989 111.603389) (xy 141.738489 111.491889) - (xy 141.826094 111.360779) (xy 141.886437 111.215097) (xy 141.9172 111.060442) (xy 141.9172 110.902758) - (xy 141.9172 110.902755) (xy 141.917199 110.902753) (xy 141.886438 110.74811) (xy 141.886437 110.748103) - (xy 141.886435 110.748098) (xy 141.826097 110.602427) (xy 141.82609 110.602414) (xy 141.738489 110.471311) - (xy 141.738486 110.471307) (xy 141.626992 110.359813) (xy 141.626988 110.35981) (xy 141.495885 110.272209) - (xy 141.495872 110.272202) (xy 141.350201 110.211864) (xy 141.350189 110.211861) (xy 141.195545 110.1811) - (xy 141.195542 110.1811) (xy 141.037858 110.1811) (xy 141.037855 110.1811) (xy 140.88321 110.211861) - (xy 140.883198 110.211864) (xy 140.737527 110.272202) (xy 140.737514 110.272209) (xy 140.606411 110.35981) - (xy 140.606407 110.359813) (xy 140.494913 110.471307) (xy 140.49491 110.471311) (xy 140.407309 110.602414) - (xy 140.407302 110.602427) (xy 140.346964 110.748098) (xy 140.346961 110.74811) (xy 140.3162 110.902753) - (xy 120.2505 110.902753) (xy 120.2505 109.62154) (xy 144.5382 109.62154) (xy 144.5382 109.768459) - (xy 144.566858 109.912534) (xy 144.566861 109.912544) (xy 144.623078 110.048266) (xy 144.623083 110.048275) - (xy 144.704698 110.170419) (xy 144.704701 110.170423) (xy 144.808576 110.274298) (xy 144.80858 110.274301) - (xy 144.930724 110.355916) (xy 144.930733 110.355921) (xy 144.9558 110.366304) (xy 145.066458 110.41214) - (xy 145.21054 110.440799) (xy 145.210544 110.4408) (xy 145.210545 110.4408) (xy 145.357456 110.4408) - (xy 145.357457 110.440799) (xy 145.501542 110.41214) (xy 145.637269 110.35592) (xy 145.75942 110.274301) - (xy 145.863301 110.17042) (xy 145.94492 110.048269) (xy 146.00114 109.912542) (xy 146.0298 109.768455) - (xy 146.0298 109.621545) (xy 146.029799 109.62154) (xy 146.5702 109.62154) (xy 146.5702 109.768459) - (xy 146.598858 109.912534) (xy 146.598861 109.912544) (xy 146.655078 110.048266) (xy 146.655083 110.048275) - (xy 146.736698 110.170419) (xy 146.736701 110.170423) (xy 146.840576 110.274298) (xy 146.84058 110.274301) - (xy 146.962724 110.355916) (xy 146.962733 110.355921) (xy 146.9878 110.366304) (xy 147.098458 110.41214) - (xy 147.24254 110.440799) (xy 147.242544 110.4408) (xy 147.242545 110.4408) (xy 147.389456 110.4408) - (xy 147.389457 110.440799) (xy 147.533542 110.41214) (xy 147.669269 110.35592) (xy 147.79142 110.274301) - (xy 147.895301 110.17042) (xy 147.97692 110.048269) (xy 148.03314 109.912542) (xy 148.0618 109.768455) - (xy 148.0618 109.621545) (xy 148.03314 109.477458) (xy 147.97692 109.341731) (xy 147.976919 109.34173) - (xy 147.976916 109.341724) (xy 147.895301 109.21958) (xy 147.895298 109.219576) (xy 147.791423 109.115701) - (xy 147.791419 109.115698) (xy 147.669275 109.034083) (xy 147.669266 109.034078) (xy 147.533544 108.977861) - (xy 147.533545 108.977861) (xy 147.533542 108.97786) (xy 147.533538 108.977859) (xy 147.533534 108.977858) - (xy 147.389459 108.9492) (xy 147.389455 108.9492) (xy 147.242545 108.9492) (xy 147.24254 108.9492) - (xy 147.098465 108.977858) (xy 147.098455 108.977861) (xy 146.962733 109.034078) (xy 146.962724 109.034083) - (xy 146.84058 109.115698) (xy 146.840576 109.115701) (xy 146.736701 109.219576) (xy 146.736698 109.21958) - (xy 146.655083 109.341724) (xy 146.655078 109.341733) (xy 146.598861 109.477455) (xy 146.598858 109.477465) - (xy 146.5702 109.62154) (xy 146.029799 109.62154) (xy 146.00114 109.477458) (xy 145.94492 109.341731) - (xy 145.944919 109.34173) (xy 145.944916 109.341724) (xy 145.863301 109.21958) (xy 145.863298 109.219576) - (xy 145.759423 109.115701) (xy 145.759419 109.115698) (xy 145.637275 109.034083) (xy 145.637266 109.034078) - (xy 145.501544 108.977861) (xy 145.501545 108.977861) (xy 145.501542 108.97786) (xy 145.501538 108.977859) - (xy 145.501534 108.977858) (xy 145.357459 108.9492) (xy 145.357455 108.9492) (xy 145.210545 108.9492) - (xy 145.21054 108.9492) (xy 145.066465 108.977858) (xy 145.066455 108.977861) (xy 144.930733 109.034078) - (xy 144.930724 109.034083) (xy 144.80858 109.115698) (xy 144.808576 109.115701) (xy 144.704701 109.219576) - (xy 144.704698 109.21958) (xy 144.623083 109.341724) (xy 144.623078 109.341733) (xy 144.566861 109.477455) - (xy 144.566858 109.477465) (xy 144.5382 109.62154) (xy 120.2505 109.62154) (xy 120.2505 108.257353) - (xy 134.9748 108.257353) (xy 134.9748 108.415046) (xy 135.005561 108.569689) (xy 135.005564 108.569701) - (xy 135.065902 108.715372) (xy 135.065909 108.715385) (xy 135.15351 108.846488) (xy 135.153513 108.846492) - (xy 135.265007 108.957986) (xy 135.265011 108.957989) (xy 135.396114 109.04559) (xy 135.396127 109.045597) - (xy 135.541798 109.105935) (xy 135.541803 109.105937) (xy 135.696453 109.136699) (xy 135.696456 109.1367) - (xy 135.696458 109.1367) (xy 135.854144 109.1367) (xy 135.854145 109.136699) (xy 136.008797 109.105937) - (xy 136.154479 109.045594) (xy 136.285589 108.957989) (xy 136.397089 108.846489) (xy 136.484694 108.715379) - (xy 136.545037 108.569697) (xy 136.5758 108.415042) (xy 136.5758 108.257358) (xy 136.5758 108.257355) - (xy 136.575799 108.257353) (xy 136.573438 108.245486) (xy 136.545037 108.102703) (xy 136.545035 108.102698) - (xy 136.484697 107.957027) (xy 136.48469 107.957014) (xy 136.397089 107.825911) (xy 136.397086 107.825907) - (xy 136.285592 107.714413) (xy 136.285588 107.71441) (xy 136.177022 107.641868) (xy 136.154485 107.626809) - (xy 136.154472 107.626802) (xy 136.008801 107.566464) (xy 136.008789 107.566461) (xy 135.90016 107.544853) - (xy 145.0503 107.544853) (xy 145.0503 107.702546) (xy 145.081061 107.857189) (xy 145.081064 107.857201) - (xy 145.141402 108.002872) (xy 145.141409 108.002885) (xy 145.22901 108.133988) (xy 145.229013 108.133992) - (xy 145.340507 108.245486) (xy 145.340511 108.245489) (xy 145.471614 108.33309) (xy 145.471627 108.333097) - (xy 145.617298 108.393435) (xy 145.617303 108.393437) (xy 145.771953 108.424199) (xy 145.771956 108.4242) - (xy 145.771958 108.4242) (xy 145.929644 108.4242) (xy 145.929645 108.424199) (xy 146.084297 108.393437) - (xy 146.229979 108.333094) (xy 146.361089 108.245489) (xy 146.472589 108.133989) (xy 146.560194 108.002879) - (xy 146.620537 107.857197) (xy 146.6513 107.702542) (xy 146.6513 107.544858) (xy 146.6513 107.544855) - (xy 146.651299 107.544853) (xy 146.620538 107.39021) (xy 146.620537 107.390203) (xy 146.594465 107.327258) - (xy 146.560197 107.244527) (xy 146.56019 107.244514) (xy 146.472589 107.113411) (xy 146.472586 107.113407) - (xy 146.361092 107.001913) (xy 146.361088 107.00191) (xy 146.229985 106.914309) (xy 146.229972 106.914302) - (xy 146.084301 106.853964) (xy 146.084289 106.853961) (xy 145.929645 106.8232) (xy 145.929642 106.8232) - (xy 145.771958 106.8232) (xy 145.771955 106.8232) (xy 145.61731 106.853961) (xy 145.617298 106.853964) - (xy 145.471627 106.914302) (xy 145.471614 106.914309) (xy 145.340511 107.00191) (xy 145.340507 107.001913) - (xy 145.229013 107.113407) (xy 145.22901 107.113411) (xy 145.141409 107.244514) (xy 145.141402 107.244527) - (xy 145.081064 107.390198) (xy 145.081061 107.39021) (xy 145.0503 107.544853) (xy 135.90016 107.544853) - (xy 135.854145 107.5357) (xy 135.854142 107.5357) (xy 135.696458 107.5357) (xy 135.696455 107.5357) - (xy 135.54181 107.566461) (xy 135.541798 107.566464) (xy 135.396127 107.626802) (xy 135.396114 107.626809) - (xy 135.265011 107.71441) (xy 135.265007 107.714413) (xy 135.153513 107.825907) (xy 135.15351 107.825911) - (xy 135.065909 107.957014) (xy 135.065902 107.957027) (xy 135.005564 108.102698) (xy 135.005561 108.10271) - (xy 134.9748 108.257353) (xy 120.2505 108.257353) (xy 120.2505 107.327253) (xy 123.7487 107.327253) - (xy 123.7487 107.484946) (xy 123.779461 107.639589) (xy 123.779464 107.639601) (xy 123.839802 107.785272) - (xy 123.839809 107.785285) (xy 123.92741 107.916388) (xy 123.927413 107.916392) (xy 124.038907 108.027886) - (xy 124.038911 108.027889) (xy 124.170014 108.11549) (xy 124.170027 108.115497) (xy 124.315698 108.175835) - (xy 124.315703 108.175837) (xy 124.470353 108.206599) (xy 124.470356 108.2066) (xy 124.470358 108.2066) - (xy 124.628044 108.2066) (xy 124.628045 108.206599) (xy 124.782697 108.175837) (xy 124.819919 108.160418) - (xy 124.877172 108.136705) (xy 124.928372 108.115497) (xy 124.928372 108.115496) (xy 124.928379 108.115494) - (xy 125.059489 108.027889) (xy 125.170989 107.916389) (xy 125.258594 107.785279) (xy 125.318937 107.639597) - (xy 125.3497 107.484942) (xy 125.3497 107.327258) (xy 125.3497 107.327255) (xy 125.349699 107.327253) - (xy 125.318937 107.172603) (xy 125.294419 107.113411) (xy 125.258597 107.026927) (xy 125.25859 107.026914) - (xy 125.170989 106.895811) (xy 125.170986 106.895807) (xy 125.059492 106.784313) (xy 125.059488 106.78431) - (xy 124.928385 106.696709) (xy 124.928372 106.696702) (xy 124.782701 106.636364) (xy 124.782689 106.636361) - (xy 124.628045 106.6056) (xy 124.628042 106.6056) (xy 124.470358 106.6056) (xy 124.470355 106.6056) - (xy 124.31571 106.636361) (xy 124.315698 106.636364) (xy 124.170027 106.696702) (xy 124.170014 106.696709) - (xy 124.038911 106.78431) (xy 124.038907 106.784313) (xy 123.927413 106.895807) (xy 123.92741 106.895811) - (xy 123.839809 107.026914) (xy 123.839802 107.026927) (xy 123.779464 107.172598) (xy 123.779461 107.17261) - (xy 123.7487 107.327253) (xy 120.2505 107.327253) (xy 120.2505 104.670153) (xy 124.1591 104.670153) - (xy 124.1591 104.827846) (xy 124.189861 104.982489) (xy 124.189864 104.982501) (xy 124.250202 105.128172) - (xy 124.250209 105.128185) (xy 124.33781 105.259288) (xy 124.337813 105.259292) (xy 124.449307 105.370786) - (xy 124.449311 105.370789) (xy 124.580414 105.45839) (xy 124.580427 105.458397) (xy 124.652826 105.488385) - (xy 124.726103 105.518737) (xy 124.880753 105.549499) (xy 124.880756 105.5495) (xy 124.880758 105.5495) - (xy 125.038444 105.5495) (xy 125.038445 105.549499) (xy 125.193097 105.518737) (xy 125.338779 105.458394) - (xy 125.469889 105.370789) (xy 125.581389 105.259289) (xy 125.668994 105.128179) (xy 125.709515 105.030353) - (xy 130.3967 105.030353) (xy 130.3967 105.188046) (xy 130.427461 105.342689) (xy 130.427464 105.342701) - (xy 130.487802 105.488372) (xy 130.487809 105.488385) (xy 130.57541 105.619488) (xy 130.575413 105.619492) - (xy 130.686907 105.730986) (xy 130.686911 105.730989) (xy 130.818014 105.81859) (xy 130.818027 105.818597) - (xy 130.963698 105.878935) (xy 130.963703 105.878937) (xy 131.118353 105.909699) (xy 131.118356 105.9097) - (xy 131.118358 105.9097) (xy 131.276044 105.9097) (xy 131.276045 105.909699) (xy 131.430697 105.878937) - (xy 131.576379 105.818594) (xy 131.707489 105.730989) (xy 131.818989 105.619489) (xy 131.906594 105.488379) - (xy 131.966937 105.342697) (xy 131.9977 105.188042) (xy 131.9977 105.030358) (xy 131.9977 105.030355) - (xy 131.997699 105.030353) (xy 131.995587 105.019735) (xy 131.966937 104.875703) (xy 131.947114 104.827846) - (xy 131.906597 104.730027) (xy 131.90659 104.730014) (xy 131.818989 104.598911) (xy 131.818986 104.598907) - (xy 131.707492 104.487413) (xy 131.707488 104.48741) (xy 131.576385 104.399809) (xy 131.576372 104.399802) - (xy 131.430701 104.339464) (xy 131.430689 104.339461) (xy 131.276045 104.3087) (xy 131.276042 104.3087) - (xy 131.118358 104.3087) (xy 131.118355 104.3087) (xy 130.96371 104.339461) (xy 130.963698 104.339464) - (xy 130.818027 104.399802) (xy 130.818014 104.399809) (xy 130.686911 104.48741) (xy 130.686907 104.487413) - (xy 130.575413 104.598907) (xy 130.57541 104.598911) (xy 130.487809 104.730014) (xy 130.487802 104.730027) - (xy 130.427464 104.875698) (xy 130.427461 104.87571) (xy 130.3967 105.030353) (xy 125.709515 105.030353) - (xy 125.729337 104.982497) (xy 125.7601 104.827842) (xy 125.7601 104.670158) (xy 125.7601 104.670155) - (xy 125.760099 104.670153) (xy 125.729338 104.51551) (xy 125.729337 104.515503) (xy 125.717701 104.48741) - (xy 125.668997 104.369827) (xy 125.66899 104.369814) (xy 125.58139 104.238712) (xy 125.581386 104.238707) - (xy 125.513832 104.171153) (xy 135.3495 104.171153) (xy 135.3495 104.328846) (xy 135.380261 104.483489) - (xy 135.380264 104.483501) (xy 135.440602 104.629172) (xy 135.440609 104.629185) (xy 135.52821 104.760288) - (xy 135.528213 104.760292) (xy 135.639707 104.871786) (xy 135.639711 104.871789) (xy 135.770814 104.95939) - (xy 135.770827 104.959397) (xy 135.916498 105.019735) (xy 135.916503 105.019737) (xy 136.071153 105.050499) - (xy 136.071156 105.0505) (xy 136.071158 105.0505) (xy 136.228844 105.0505) (xy 136.228845 105.050499) - (xy 136.383497 105.019737) (xy 136.529179 104.959394) (xy 136.660289 104.871789) (xy 136.771789 104.760289) - (xy 136.859394 104.629179) (xy 136.919737 104.483497) (xy 136.9505 104.328842) (xy 136.9505 104.171158) - (xy 136.9505 104.171155) (xy 136.950499 104.171153) (xy 136.924333 104.039609) (xy 136.919737 104.016503) - (xy 136.904311 103.979261) (xy 136.859397 103.870827) (xy 136.85939 103.870814) (xy 136.771789 103.739711) - (xy 136.771786 103.739707) (xy 136.660292 103.628213) (xy 136.660288 103.62821) (xy 136.529185 103.540609) - (xy 136.529172 103.540602) (xy 136.383501 103.480264) (xy 136.383489 103.480261) (xy 136.228845 103.4495) - (xy 136.228842 103.4495) (xy 136.071158 103.4495) (xy 136.071155 103.4495) (xy 135.91651 103.480261) - (xy 135.916498 103.480264) (xy 135.770827 103.540602) (xy 135.770814 103.540609) (xy 135.639711 103.62821) - (xy 135.639707 103.628213) (xy 135.528213 103.739707) (xy 135.52821 103.739711) (xy 135.440609 103.870814) - (xy 135.440602 103.870827) (xy 135.380264 104.016498) (xy 135.380261 104.01651) (xy 135.3495 104.171153) - (xy 125.513832 104.171153) (xy 125.469892 104.127213) (xy 125.469888 104.12721) (xy 125.338785 104.039609) - (xy 125.338772 104.039602) (xy 125.193101 103.979264) (xy 125.193089 103.979261) (xy 125.038445 103.9485) - (xy 125.038442 103.9485) (xy 124.880758 103.9485) (xy 124.880755 103.9485) (xy 124.72611 103.979261) - (xy 124.726098 103.979264) (xy 124.580427 104.039602) (xy 124.580414 104.039609) (xy 124.449311 104.12721) - (xy 124.449307 104.127213) (xy 124.337813 104.238707) (xy 124.33781 104.238711) (xy 124.250209 104.369814) - (xy 124.250202 104.369827) (xy 124.189864 104.515498) (xy 124.189861 104.51551) (xy 124.1591 104.670153) - (xy 120.2505 104.670153) (xy 120.2505 100.321153) (xy 125.9348 100.321153) (xy 125.9348 100.478846) - (xy 125.965561 100.633489) (xy 125.965564 100.633501) (xy 126.025902 100.779172) (xy 126.025909 100.779185) - (xy 126.11351 100.910288) (xy 126.113513 100.910292) (xy 126.225007 101.021786) (xy 126.225011 101.021789) - (xy 126.356114 101.10939) (xy 126.356127 101.109397) (xy 126.501798 101.169735) (xy 126.501803 101.169737) - (xy 126.656453 101.200499) (xy 126.656456 101.2005) (xy 126.656458 101.2005) (xy 126.814144 101.2005) - (xy 126.814145 101.200499) (xy 126.968797 101.169737) (xy 127.114479 101.109394) (xy 127.245589 101.021789) - (xy 127.357089 100.910289) (xy 127.444694 100.779179) (xy 127.505037 100.633497) (xy 127.5358 100.478842) - (xy 127.5358 100.321158) (xy 127.5358 100.321155) (xy 127.535799 100.321153) (xy 127.525558 100.269669) - (xy 127.505037 100.166503) (xy 127.479752 100.105458) (xy 127.444697 100.020827) (xy 127.44469 100.020814) - (xy 127.357089 99.889711) (xy 127.357086 99.889707) (xy 127.245592 99.778213) (xy 127.245588 99.77821) - (xy 127.114485 99.690609) (xy 127.114472 99.690602) (xy 126.968801 99.630264) (xy 126.968789 99.630261) - (xy 126.814145 99.5995) (xy 126.814142 99.5995) (xy 126.656458 99.5995) (xy 126.656455 99.5995) - (xy 126.50181 99.630261) (xy 126.501798 99.630264) (xy 126.356127 99.690602) (xy 126.356114 99.690609) - (xy 126.225011 99.77821) (xy 126.225007 99.778213) (xy 126.113513 99.889707) (xy 126.11351 99.889711) - (xy 126.025909 100.020814) (xy 126.025902 100.020827) (xy 125.965564 100.166498) (xy 125.965561 100.16651) - (xy 125.9348 100.321153) (xy 120.2505 100.321153) (xy 120.2505 98.158653) (xy 128.8245 98.158653) - (xy 128.8245 98.316346) (xy 128.855261 98.470989) (xy 128.855264 98.471001) (xy 128.915602 98.616672) - (xy 128.915609 98.616685) (xy 129.00321 98.747788) (xy 129.003213 98.747792) (xy 129.114707 98.859286) - (xy 129.114711 98.859289) (xy 129.245814 98.94689) (xy 129.251191 98.949764) (xy 129.250422 98.951202) - (xy 129.298693 98.9901) (xy 129.320758 99.056394) (xy 129.303479 99.124094) (xy 129.284519 99.148501) - (xy 129.249614 99.183406) (xy 129.24961 99.183411) (xy 129.162009 99.314514) (xy 129.162002 99.314527) - (xy 129.101664 99.460198) (xy 129.101661 99.46021) (xy 129.0709 99.614853) (xy 129.0709 99.772546) - (xy 129.101661 99.927189) (xy 129.101664 99.927201) (xy 129.162003 100.072874) (xy 129.163113 100.074535) - (xy 129.163426 100.075536) (xy 129.164875 100.078246) (xy 129.16436 100.07852) (xy 129.183987 100.141214) - (xy 129.165499 100.208593) (xy 129.163109 100.212312) (xy 129.090609 100.320814) (xy 129.090602 100.320827) - (xy 129.030264 100.466498) (xy 129.030261 100.46651) (xy 128.9995 100.621153) (xy 128.9995 100.778846) - (xy 129.030261 100.933489) (xy 129.030264 100.933501) (xy 129.090602 101.079172) (xy 129.090609 101.079185) - (xy 129.17821 101.210288) (xy 129.178213 101.210292) (xy 129.25219 101.284269) (xy 129.285675 101.345592) - (xy 129.280691 101.415284) (xy 129.252193 101.459629) (xy 129.239908 101.471914) (xy 129.152309 101.603014) - (xy 129.152302 101.603027) (xy 129.091964 101.748698) (xy 129.091961 101.74871) (xy 129.0612 101.903353) - (xy 129.0612 102.061046) (xy 129.091961 102.215689) (xy 129.091964 102.215701) (xy 129.152302 102.361372) - (xy 129.152309 102.361385) (xy 129.23991 102.492488) (xy 129.239913 102.492492) (xy 129.351407 102.603986) - (xy 129.351411 102.603989) (xy 129.482514 102.69159) (xy 129.482527 102.691597) (xy 129.628198 102.751935) - (xy 129.628203 102.751937) (xy 129.782853 102.782699) (xy 129.782856 102.7827) (xy 129.782858 102.7827) - (xy 129.940544 102.7827) (xy 129.940545 102.782699) (xy 130.095197 102.751937) (xy 130.240879 102.691594) - (xy 130.371989 102.603989) (xy 130.483489 102.492489) (xy 130.571094 102.361379) (xy 130.631437 102.215697) - (xy 130.6622 102.061042) (xy 130.6622 101.903358) (xy 130.6622 101.903355) (xy 130.662199 101.903353) - (xy 130.631438 101.74871) (xy 130.631437 101.748703) (xy 130.631435 101.748698) (xy 130.571097 101.603027) - (xy 130.57109 101.603014) (xy 130.483489 101.471911) (xy 130.483486 101.471907) (xy 130.409509 101.39793) - (xy 130.376024 101.336607) (xy 130.381008 101.266915) (xy 130.409507 101.22257) (xy 130.421789 101.210289) - (xy 130.509394 101.079179) (xy 130.569737 100.933497) (xy 130.6005 100.778842) (xy 130.6005 100.621158) - (xy 130.6005 100.621155) (xy 130.600499 100.621153) (xy 130.572192 100.478846) (xy 130.569737 100.466503) - (xy 130.549564 100.417801) (xy 130.509397 100.320827) (xy 130.509395 100.320824) (xy 130.509394 100.320821) - (xy 130.508291 100.319171) (xy 130.50798 100.318176) (xy 130.506525 100.315454) (xy 130.507041 100.315178) - (xy 130.503014 100.302318) (xy 130.49316 100.287659) (xy 130.492789 100.269669) (xy 130.487412 100.252499) - (xy 130.492082 100.23538) (xy 130.49172 100.217804) (xy 130.504601 100.189494) (xy 130.505717 100.185404) - (xy 130.506959 100.183379) (xy 130.559028 100.105453) (xy 138.4088 100.105453) (xy 138.4088 100.263146) - (xy 138.439561 100.417789) (xy 138.439564 100.417801) (xy 138.499902 100.563472) (xy 138.499909 100.563485) - (xy 138.58751 100.694588) (xy 138.587513 100.694592) (xy 138.699007 100.806086) (xy 138.699011 100.806089) - (xy 138.830114 100.89369) (xy 138.830127 100.893697) (xy 138.926224 100.933501) (xy 138.975803 100.954037) - (xy 139.130453 100.984799) (xy 139.130456 100.9848) (xy 139.130458 100.9848) (xy 139.288144 100.9848) - (xy 139.288145 100.984799) (xy 139.442797 100.954037) (xy 139.588479 100.893694) (xy 139.719589 100.806089) - (xy 139.831089 100.694589) (xy 139.918694 100.563479) (xy 139.979037 100.417797) (xy 140.0098 100.263142) - (xy 140.0098 100.105458) (xy 140.0098 100.105455) (xy 140.009799 100.105453) (xy 140.003319 100.072874) - (xy 139.979037 99.950803) (xy 139.953732 99.889711) (xy 139.918697 99.805127) (xy 139.91869 99.805114) - (xy 139.831089 99.674011) (xy 139.831086 99.674007) (xy 139.719592 99.562513) (xy 139.719588 99.56251) - (xy 139.588485 99.474909) (xy 139.588472 99.474902) (xy 139.568577 99.466662) (xy 139.568572 99.46666) - (xy 139.442797 99.414563) (xy 139.356071 99.397312) (xy 139.356056 99.397307) (xy 139.288146 99.3838) - (xy 139.288142 99.3838) (xy 139.130458 99.3838) (xy 139.130455 99.3838) (xy 138.97581 99.414561) - (xy 138.975798 99.414564) (xy 138.830127 99.474902) (xy 138.830114 99.474909) (xy 138.699011 99.56251) - (xy 138.699007 99.562513) (xy 138.587513 99.674007) (xy 138.58751 99.674011) (xy 138.499909 99.805114) - (xy 138.499902 99.805127) (xy 138.439564 99.950798) (xy 138.439561 99.95081) (xy 138.4088 100.105453) - (xy 130.559028 100.105453) (xy 130.580794 100.072879) (xy 130.641137 99.927197) (xy 130.6719 99.772542) - (xy 130.6719 99.614858) (xy 130.6719 99.614855) (xy 130.671899 99.614853) (xy 130.644062 99.474909) - (xy 130.641137 99.460203) (xy 130.622233 99.414564) (xy 130.580797 99.314527) (xy 130.58079 99.314514) - (xy 130.493189 99.183411) (xy 130.493186 99.183407) (xy 130.381692 99.071913) (xy 130.381688 99.07191) - (xy 130.250585 98.984309) (xy 130.245209 98.981436) (xy 130.245976 98.98) (xy 130.197698 98.941086) - (xy 130.175641 98.87479) (xy 130.192928 98.807092) (xy 130.211882 98.782696) (xy 130.246786 98.747792) - (xy 130.246789 98.747789) (xy 130.334394 98.616679) (xy 130.394737 98.470997) (xy 130.4255 98.316342) - (xy 130.4255 98.158658) (xy 130.4255 98.158655) (xy 130.425499 98.158653) (xy 130.410078 98.081127) - (xy 130.394737 98.004003) (xy 130.365415 97.933213) (xy 130.334397 97.858327) (xy 130.33439 97.858314) - (xy 130.246789 97.727211) (xy 130.246786 97.727207) (xy 130.135292 97.615713) (xy 130.135288 97.61571) - (xy 130.004185 97.528109) (xy 130.004172 97.528102) (xy 129.858501 97.467764) (xy 129.858489 97.467761) - (xy 129.703845 97.437) (xy 129.703842 97.437) (xy 129.546158 97.437) (xy 129.546155 97.437) (xy 129.39151 97.467761) - (xy 129.391498 97.467764) (xy 129.245827 97.528102) (xy 129.245814 97.528109) (xy 129.114711 97.61571) - (xy 129.114707 97.615713) (xy 129.003213 97.727207) (xy 129.00321 97.727211) (xy 128.915609 97.858314) - (xy 128.915602 97.858327) (xy 128.855264 98.003998) (xy 128.855261 98.00401) (xy 128.8245 98.158653) - (xy 120.2505 98.158653) (xy 120.2505 97.940666) (xy 120.270185 97.873627) (xy 120.322989 97.827872) - (xy 120.392147 97.817928) (xy 120.421951 97.826105) (xy 120.426217 97.827872) (xy 120.455097 97.839835) - (xy 120.455099 97.839835) (xy 120.455103 97.839837) (xy 120.609753 97.870599) (xy 120.609756 97.8706) - (xy 120.609758 97.8706) (xy 120.767444 97.8706) (xy 120.767445 97.870599) (xy 120.922097 97.839837) - (xy 121.067779 97.779494) (xy 121.198889 97.691889) (xy 121.310389 97.580389) (xy 121.397994 97.449279) - (xy 121.397995 97.449276) (xy 121.397997 97.449273) (xy 121.445077 97.335609) (xy 121.45594 97.309382) - (xy 121.49978 97.254979) (xy 121.54631 97.235217) (xy 121.561297 97.232237) (xy 121.706979 97.171894) - (xy 121.838089 97.084289) (xy 121.949589 96.972789) (xy 122.037194 96.841679) (xy 122.039838 96.835297) - (xy 122.097535 96.696001) (xy 122.097537 96.695997) (xy 122.1283 96.541342) (xy 122.1283 96.383658) - (xy 122.1283 96.383655) (xy 122.128299 96.383653) (xy 122.125245 96.368298) (xy 122.097537 96.229003) - (xy 122.053431 96.122521) (xy 122.037197 96.083327) (xy 122.03719 96.083314) (xy 121.949589 95.952211) - (xy 121.949586 95.952207) (xy 121.838092 95.840713) (xy 121.838088 95.84071) (xy 121.706985 95.753109) - (xy 121.706972 95.753102) (xy 121.561301 95.692764) (xy 121.561289 95.692761) (xy 121.406645 95.662) - (xy 121.406642 95.662) (xy 121.248958 95.662) (xy 121.248955 95.662) (xy 121.09431 95.692761) (xy 121.094298 95.692764) - (xy 120.948627 95.753102) (xy 120.948614 95.753109) (xy 120.817511 95.84071) (xy 120.817507 95.840713) - (xy 120.706013 95.952207) (xy 120.70601 95.952211) (xy 120.618409 96.083314) (xy 120.618404 96.083323) - (xy 120.560459 96.223217) (xy 120.516618 96.27762) (xy 120.470091 96.297381) (xy 120.455107 96.300361) - (xy 120.4551 96.300363) (xy 120.421952 96.314094) (xy 120.352482 96.321563) (xy 120.290003 96.290287) - (xy 120.254352 96.230198) (xy 120.2505 96.199533) (xy 120.2505 95.530753) (xy 129.4068 95.530753) - (xy 129.4068 95.688446) (xy 129.437561 95.843089) (xy 129.437564 95.843101) (xy 129.497902 95.988772) - (xy 129.497909 95.988785) (xy 129.58551 96.119888) (xy 129.585513 96.119892) (xy 129.592671 96.12705) - (xy 129.626156 96.188373) (xy 129.621172 96.258065) (xy 129.619553 96.262178) (xy 129.617765 96.266493) - (xy 129.617761 96.266505) (xy 129.587 96.421153) (xy 129.587 96.578846) (xy 129.617761 96.733489) - (xy 129.617764 96.733501) (xy 129.678102 96.879172) (xy 129.678109 96.879185) (xy 129.76571 97.010288) - (xy 129.765713 97.010292) (xy 129.877207 97.121786) (xy 129.877211 97.121789) (xy 130.008314 97.20939) - (xy 130.008327 97.209397) (xy 130.153998 97.269735) (xy 130.154003 97.269737) (xy 130.308653 97.300499) - (xy 130.308656 97.3005) (xy 130.308658 97.3005) (xy 130.466344 97.3005) (xy 130.466345 97.300499) - (xy 130.620997 97.269737) (xy 130.766679 97.209394) (xy 130.897789 97.121789) (xy 131.009289 97.010289) - (xy 131.096894 96.879179) (xy 131.157237 96.733497) (xy 131.188 96.578842) (xy 131.188 96.422853) - (xy 138.6841 96.422853) (xy 138.6841 96.580546) (xy 138.714861 96.735189) (xy 138.714864 96.735201) - (xy 138.775202 96.880872) (xy 138.775209 96.880885) (xy 138.862809 97.011987) (xy 138.86281 97.011988) - (xy 138.862811 97.011989) (xy 138.884324 97.033502) (xy 138.917809 97.094823) (xy 138.912826 97.164514) - (xy 138.911204 97.168635) (xy 138.867064 97.275198) (xy 138.867061 97.27521) (xy 138.8363 97.429853) - (xy 138.8363 97.587546) (xy 138.867061 97.742189) (xy 138.867064 97.742201) (xy 138.927402 97.887872) - (xy 138.927409 97.887885) (xy 139.01501 98.018988) (xy 139.015013 98.018992) (xy 139.015825 98.019804) - (xy 139.016114 98.020333) (xy 139.018876 98.023699) (xy 139.018237 98.024222) (xy 139.04931 98.081127) - (xy 139.044326 98.150819) (xy 139.042706 98.154935) (xy 139.020063 98.209602) (xy 139.02006 98.209611) - (xy 138.9893 98.364253) (xy 138.9893 98.521946) (xy 139.020061 98.676589) (xy 139.020064 98.676601) - (xy 139.080402 98.822272) (xy 139.080409 98.822285) (xy 139.16801 98.953388) (xy 139.168013 98.953392) - (xy 139.279507 99.064886) (xy 139.279511 99.064889) (xy 139.410614 99.15249) (xy 139.410621 99.152494) - (xy 139.556303 99.212837) (xy 139.669355 99.235324) (xy 139.710955 99.2436) (xy 139.710958 99.2436) - (xy 139.868644 99.2436) (xy 139.868645 99.243599) (xy 140.023297 99.212837) (xy 140.168979 99.152494) - (xy 140.300089 99.064889) (xy 140.411589 98.953389) (xy 140.499194 98.822279) (xy 140.559537 98.676597) - (xy 140.5903 98.521942) (xy 140.5903 98.364258) (xy 140.5903 98.364255) (xy 140.590299 98.364253) - (xy 140.573239 98.278489) (xy 140.559537 98.209603) (xy 140.506321 98.081127) (xy 140.499197 98.063927) - (xy 140.499193 98.06392) (xy 140.433867 97.966153) (xy 144.6524 97.966153) (xy 144.6524 98.123846) - (xy 144.683161 98.278489) (xy 144.683164 98.278501) (xy 144.743502 98.424172) (xy 144.743509 98.424185) - (xy 144.83111 98.555288) (xy 144.831113 98.555292) (xy 144.942607 98.666786) (xy 144.942611 98.666789) - (xy 145.073714 98.75439) (xy 145.073727 98.754397) (xy 145.156063 98.788501) (xy 145.219403 98.814737) - (xy 145.257284 98.822272) (xy 145.309178 98.832595) (xy 145.371089 98.86498) (xy 145.399548 98.906759) - (xy 145.410904 98.934175) (xy 145.410909 98.934185) (xy 145.49851 99.065288) (xy 145.498513 99.065292) - (xy 145.610007 99.176786) (xy 145.610011 99.176789) (xy 145.741114 99.26439) (xy 145.741127 99.264397) - (xy 145.886798 99.324735) (xy 145.886803 99.324737) (xy 146.041453 99.355499) (xy 146.041456 99.3555) - (xy 146.041458 99.3555) (xy 146.199144 99.3555) (xy 146.199145 99.355499) (xy 146.353797 99.324737) - (xy 146.499479 99.264394) (xy 146.630589 99.176789) (xy 146.742089 99.065289) (xy 146.829694 98.934179) - (xy 146.890037 98.788497) (xy 146.9208 98.633842) (xy 146.9208 98.476158) (xy 146.9208 98.476155) - (xy 146.920799 98.476153) (xy 146.910459 98.424172) (xy 146.890037 98.321503) (xy 146.872225 98.278501) - (xy 146.829697 98.175827) (xy 146.82969 98.175814) (xy 146.742089 98.044711) (xy 146.742086 98.044707) - (xy 146.630592 97.933213) (xy 146.630588 97.93321) (xy 146.499485 97.845609) (xy 146.499472 97.845602) - (xy 146.353801 97.785264) (xy 146.353791 97.785261) (xy 146.26402 97.767404) (xy 146.202109 97.735018) - (xy 146.17365 97.693238) (xy 146.173091 97.691889) (xy 146.162294 97.665821) (xy 146.16229 97.665814) - (xy 146.074689 97.534711) (xy 146.074686 97.534707) (xy 145.963192 97.423213) (xy 145.963188 97.42321) - (xy 145.832085 97.335609) (xy 145.832072 97.335602) (xy 145.686401 97.275264) (xy 145.686389 97.275261) - (xy 145.531745 97.2445) (xy 145.531742 97.2445) (xy 145.374058 97.2445) (xy 145.374055 97.2445) - (xy 145.21941 97.275261) (xy 145.219398 97.275264) (xy 145.073727 97.335602) (xy 145.073714 97.335609) - (xy 144.942611 97.42321) (xy 144.942607 97.423213) (xy 144.831113 97.534707) (xy 144.83111 97.534711) - (xy 144.743509 97.665814) (xy 144.743502 97.665827) (xy 144.683164 97.811498) (xy 144.683161 97.81151) - (xy 144.6524 97.966153) (xy 140.433867 97.966153) (xy 140.411589 97.932811) (xy 140.402958 97.92418) - (xy 140.396645 97.9151) (xy 140.388947 97.892022) (xy 140.377289 97.870672) (xy 140.378089 97.859471) - (xy 140.374537 97.84882) (xy 140.380537 97.825245) (xy 140.382273 97.80098) (xy 140.383894 97.796861) - (xy 140.388699 97.785261) (xy 140.406537 97.742197) (xy 140.4373 97.587542) (xy 140.4373 97.429858) - (xy 140.4373 97.429855) (xy 140.437299 97.429853) (xy 140.420065 97.343214) (xy 140.406537 97.275203) - (xy 140.396355 97.250621) (xy 140.346197 97.129527) (xy 140.34619 97.129514) (xy 140.258589 96.998411) - (xy 140.258586 96.998407) (xy 140.237076 96.976897) (xy 140.203591 96.915574) (xy 140.208575 96.845882) - (xy 140.210196 96.841763) (xy 140.254337 96.735197) (xy 140.2851 96.580542) (xy 140.2851 96.422858) - (xy 140.2851 96.422855) (xy 140.285099 96.422853) (xy 140.280568 96.400075) (xy 140.254337 96.268203) - (xy 140.238098 96.228998) (xy 140.193997 96.122527) (xy 140.19399 96.122514) (xy 140.106389 95.991411) - (xy 140.106386 95.991407) (xy 139.994892 95.879913) (xy 139.994888 95.87991) (xy 139.863785 95.792309) - (xy 139.863772 95.792302) (xy 139.718101 95.731964) (xy 139.718089 95.731961) (xy 139.563445 95.7012) - (xy 139.563442 95.7012) (xy 139.405758 95.7012) (xy 139.405755 95.7012) (xy 139.25111 95.731961) - (xy 139.251098 95.731964) (xy 139.105427 95.792302) (xy 139.105414 95.792309) (xy 138.974311 95.87991) - (xy 138.974307 95.879913) (xy 138.862813 95.991407) (xy 138.86281 95.991411) (xy 138.775209 96.122514) - (xy 138.775202 96.122527) (xy 138.714864 96.268198) (xy 138.714861 96.26821) (xy 138.6841 96.422853) - (xy 131.188 96.422853) (xy 131.188 96.421158) (xy 131.188 96.421155) (xy 131.187999 96.421153) (xy 131.168189 96.321563) - (xy 131.157237 96.266503) (xy 131.141702 96.228998) (xy 131.096897 96.120827) (xy 131.09689 96.120814) - (xy 131.009289 95.989711) (xy 131.009286 95.989707) (xy 131.002128 95.982549) (xy 130.968643 95.921226) - (xy 130.973627 95.851534) (xy 130.975249 95.847413) (xy 130.977037 95.843097) (xy 131.000114 95.72708) - (xy 131.032498 95.66517) (xy 131.093214 95.630596) (xy 131.162983 95.634335) (xy 131.209412 95.663591) - (xy 131.286707 95.740886) (xy 131.286711 95.740889) (xy 131.417814 95.82849) (xy 131.417827 95.828497) - (xy 131.552286 95.884191) (xy 131.563503 95.888837) (xy 131.718153 95.919599) (xy 131.718156 95.9196) - (xy 131.718158 95.9196) (xy 131.875844 95.9196) (xy 131.875845 95.919599) (xy 132.030497 95.888837) - (xy 132.143166 95.842167) (xy 132.176172 95.828497) (xy 132.176172 95.828496) (xy 132.176179 95.828494) - (xy 132.307289 95.740889) (xy 132.418789 95.629389) (xy 132.506394 95.498279) (xy 132.5158 95.475572) - (xy 132.520067 95.465266) (xy 132.566737 95.352597) (xy 132.5975 95.197942) (xy 132.5975 95.040258) - (xy 132.596586 95.035663) (xy 132.596586 95.03566) (xy 132.596585 95.035657) (xy 132.592984 95.017553) - (xy 133.9745 95.017553) (xy 133.9745 95.175246) (xy 134.005261 95.329889) (xy 134.005264 95.329901) - (xy 134.065602 95.475572) (xy 134.065609 95.475585) (xy 134.15321 95.606688) (xy 134.153213 95.606692) - (xy 134.264707 95.718186) (xy 134.264711 95.718189) (xy 134.395814 95.80579) (xy 134.395827 95.805797) - (xy 134.541498 95.866135) (xy 134.541503 95.866137) (xy 134.696153 95.896899) (xy 134.696156 95.8969) - (xy 134.696158 95.8969) (xy 134.853844 95.8969) (xy 134.853845 95.896899) (xy 135.008497 95.866137) - (xy 135.154179 95.805794) (xy 135.285289 95.718189) (xy 135.396789 95.606689) (xy 135.484394 95.475579) - (xy 135.544737 95.329897) (xy 135.5755 95.175242) (xy 135.5755 95.162753) (xy 137.1012 95.162753) - (xy 137.1012 95.320446) (xy 137.131961 95.475089) (xy 137.131964 95.475101) (xy 137.192302 95.620772) - (xy 137.192309 95.620785) (xy 137.27991 95.751888) (xy 137.279913 95.751892) (xy 137.391407 95.863386) - (xy 137.391411 95.863389) (xy 137.522514 95.95099) (xy 137.522527 95.950997) (xy 137.642093 96.000522) - (xy 137.668203 96.011337) (xy 137.822853 96.042099) (xy 137.822856 96.0421) (xy 137.822858 96.0421) - (xy 137.980544 96.0421) (xy 137.980545 96.042099) (xy 138.135197 96.011337) (xy 138.280879 95.950994) - (xy 138.411989 95.863389) (xy 138.523489 95.751889) (xy 138.611094 95.620779) (xy 138.671437 95.475097) - (xy 138.7022 95.320442) (xy 138.7022 95.162758) (xy 138.7022 95.162755) (xy 138.702199 95.162753) - (xy 138.671437 95.008103) (xy 138.663032 94.987811) (xy 138.611097 94.862427) (xy 138.61109 94.862414) - (xy 138.523489 94.731311) (xy 138.523486 94.731307) (xy 138.411992 94.619813) (xy 138.411988 94.61981) - (xy 138.280885 94.532209) (xy 138.280872 94.532202) (xy 138.135201 94.471864) (xy 138.135189 94.471861) - (xy 137.980545 94.4411) (xy 137.980542 94.4411) (xy 137.822858 94.4411) (xy 137.822855 94.4411) - (xy 137.66821 94.471861) (xy 137.668198 94.471864) (xy 137.522527 94.532202) (xy 137.522514 94.532209) - (xy 137.391411 94.61981) (xy 137.391407 94.619813) (xy 137.279913 94.731307) (xy 137.27991 94.731311) - (xy 137.192309 94.862414) (xy 137.192302 94.862427) (xy 137.131964 95.008098) (xy 137.131961 95.00811) - (xy 137.1012 95.162753) (xy 135.5755 95.162753) (xy 135.5755 95.017558) (xy 135.5755 95.017555) - (xy 135.575499 95.017553) (xy 135.573618 95.008098) (xy 135.544737 94.862903) (xy 135.544537 94.862421) - (xy 135.484397 94.717227) (xy 135.48439 94.717214) (xy 135.396789 94.586111) (xy 135.396786 94.586107) - (xy 135.285292 94.474613) (xy 135.285288 94.47461) (xy 135.154185 94.387009) (xy 135.154172 94.387002) - (xy 135.008501 94.326664) (xy 135.008489 94.326661) (xy 134.853845 94.2959) (xy 134.853842 94.2959) - (xy 134.696158 94.2959) (xy 134.696155 94.2959) (xy 134.54151 94.326661) (xy 134.541498 94.326664) - (xy 134.395827 94.387002) (xy 134.395814 94.387009) (xy 134.264711 94.47461) (xy 134.264707 94.474613) - (xy 134.153213 94.586107) (xy 134.15321 94.586111) (xy 134.065609 94.717214) (xy 134.065602 94.717227) - (xy 134.005264 94.862898) (xy 134.005261 94.86291) (xy 133.9745 95.017553) (xy 132.592984 95.017553) - (xy 132.569642 94.900209) (xy 132.566737 94.885603) (xy 132.557337 94.86291) (xy 132.506397 94.739927) - (xy 132.50639 94.739914) (xy 132.418789 94.608811) (xy 132.418786 94.608807) (xy 132.307292 94.497313) - (xy 132.307288 94.49731) (xy 132.176185 94.409709) (xy 132.176172 94.409702) (xy 132.030501 94.349364) - (xy 132.030489 94.349361) (xy 131.875845 94.3186) (xy 131.875842 94.3186) (xy 131.718158 94.3186) - (xy 131.718155 94.3186) (xy 131.56351 94.349361) (xy 131.563498 94.349364) (xy 131.417827 94.409702) - (xy 131.417814 94.409709) (xy 131.286711 94.49731) (xy 131.286707 94.497313) (xy 131.175213 94.608807) - (xy 131.17521 94.608811) (xy 131.087609 94.739914) (xy 131.087602 94.739927) (xy 131.027264 94.885598) - (xy 131.027261 94.885608) (xy 131.004185 95.001619) (xy 130.9718 95.06353) (xy 130.911084 95.098104) - (xy 130.841314 95.094363) (xy 130.794887 95.065108) (xy 130.717592 94.987813) (xy 130.717588 94.98781) - (xy 130.586485 94.900209) (xy 130.586472 94.900202) (xy 130.440801 94.839864) (xy 130.440789 94.839861) - (xy 130.286145 94.8091) (xy 130.286142 94.8091) (xy 130.128458 94.8091) (xy 130.128455 94.8091) - (xy 129.97381 94.839861) (xy 129.973798 94.839864) (xy 129.828127 94.900202) (xy 129.828114 94.900209) - (xy 129.697011 94.98781) (xy 129.697007 94.987813) (xy 129.585513 95.099307) (xy 129.58551 95.099311) - (xy 129.497909 95.230414) (xy 129.497902 95.230427) (xy 129.437564 95.376098) (xy 129.437561 95.37611) - (xy 129.4068 95.530753) (xy 120.2505 95.530753) (xy 120.2505 93.597753) (xy 125.8696 93.597753) - (xy 125.8696 93.755446) (xy 125.900361 93.910089) (xy 125.900364 93.910101) (xy 125.960702 94.055772) - (xy 125.960709 94.055785) (xy 126.04831 94.186888) (xy 126.048313 94.186892) (xy 126.159807 94.298386) - (xy 126.159811 94.298389) (xy 126.290914 94.38599) (xy 126.290927 94.385997) (xy 126.436598 94.446335) - (xy 126.436603 94.446337) (xy 126.56492 94.471861) (xy 126.591253 94.477099) (xy 126.591256 94.4771) - (xy 126.591258 94.4771) (xy 126.748944 94.4771) (xy 126.748945 94.477099) (xy 126.903597 94.446337) - (xy 127.046836 94.387006) (xy 127.049272 94.385997) (xy 127.049272 94.385996) (xy 127.049279 94.385994) - (xy 127.180389 94.298389) (xy 127.291889 94.186889) (xy 127.379494 94.055779) (xy 127.3957 94.016655) - (xy 127.395701 94.016653) (xy 128.2645 94.016653) (xy 128.2645 94.174346) (xy 128.295261 94.328989) - (xy 128.295264 94.329001) (xy 128.355602 94.474672) (xy 128.355609 94.474685) (xy 128.44321 94.605788) - (xy 128.443213 94.605792) (xy 128.554707 94.717286) (xy 128.554711 94.717289) (xy 128.685814 94.80489) - (xy 128.685827 94.804897) (xy 128.824719 94.862427) (xy 128.831503 94.865237) (xy 128.986153 94.895999) - (xy 128.986156 94.896) (xy 128.986158 94.896) (xy 129.143844 94.896) (xy 129.143845 94.895999) (xy 129.298497 94.865237) - (xy 129.444179 94.804894) (xy 129.575289 94.717289) (xy 129.686789 94.605789) (xy 129.774394 94.474679) - (xy 129.775561 94.471863) (xy 129.81113 94.38599) (xy 129.834737 94.328997) (xy 129.8655 94.174342) - (xy 129.8655 94.016658) (xy 129.8655 94.016655) (xy 129.865499 94.016653) (xy 129.844304 93.910101) - (xy 129.834737 93.862003) (xy 129.7906 93.755446) (xy 129.774397 93.716327) (xy 129.77439 93.716314) - (xy 129.686789 93.585211) (xy 129.686786 93.585207) (xy 129.575292 93.473713) (xy 129.575288 93.47371) - (xy 129.444185 93.386109) (xy 129.444172 93.386102) (xy 129.298501 93.325764) (xy 129.298489 93.325761) - (xy 129.143845 93.295) (xy 129.143842 93.295) (xy 128.986158 93.295) (xy 128.986155 93.295) (xy 128.83151 93.325761) - (xy 128.831498 93.325764) (xy 128.685827 93.386102) (xy 128.685814 93.386109) (xy 128.554711 93.47371) - (xy 128.554707 93.473713) (xy 128.443213 93.585207) (xy 128.44321 93.585211) (xy 128.355609 93.716314) - (xy 128.355602 93.716327) (xy 128.295264 93.861998) (xy 128.295261 93.86201) (xy 128.2645 94.016653) - (xy 127.395701 94.016653) (xy 127.417877 93.963114) (xy 127.417877 93.963113) (xy 127.439837 93.910097) - (xy 127.4706 93.755442) (xy 127.4706 93.597758) (xy 127.4706 93.597755) (xy 127.470599 93.597753) - (xy 127.441884 93.453391) (xy 127.448111 93.3838) (xy 127.490974 93.328622) (xy 127.556864 93.305378) - (xy 127.563501 93.3052) (xy 127.604544 93.3052) (xy 127.604545 93.305199) (xy 127.759197 93.274437) - (xy 127.904879 93.214094) (xy 128.035989 93.126489) (xy 128.147489 93.014989) (xy 128.235094 92.883879) - (xy 128.235935 92.88185) (xy 128.274351 92.789104) (xy 128.295437 92.738197) (xy 128.297996 92.72533) - (xy 128.301373 92.708353) (xy 133.9086 92.708353) (xy 133.9086 92.866046) (xy 133.939361 93.020689) - (xy 133.939364 93.020701) (xy 133.999702 93.166372) (xy 133.999709 93.166385) (xy 134.08731 93.297488) - (xy 134.087313 93.297492) (xy 134.198807 93.408986) (xy 134.198811 93.408989) (xy 134.329914 93.49659) - (xy 134.329927 93.496597) (xy 134.475598 93.556935) (xy 134.475603 93.556937) (xy 134.617725 93.585207) - (xy 134.630253 93.587699) (xy 134.630256 93.5877) (xy 134.630258 93.5877) (xy 134.787944 93.5877) - (xy 134.787945 93.587699) (xy 134.942597 93.556937) (xy 135.088279 93.496594) (xy 135.219389 93.408989) - (xy 135.227623 93.400754) (xy 135.288941 93.36727) (xy 135.358633 93.372252) (xy 135.362756 93.373874) - (xy 135.500998 93.431135) (xy 135.501003 93.431137) (xy 135.612881 93.453391) (xy 135.655653 93.461899) - (xy 135.655656 93.4619) (xy 135.655658 93.4619) (xy 135.813344 93.4619) (xy 135.813345 93.461899) - (xy 135.967997 93.431137) (xy 136.081106 93.384286) (xy 136.113672 93.370797) (xy 136.113672 93.370796) - (xy 136.113679 93.370794) (xy 136.244789 93.283189) (xy 136.356289 93.171689) (xy 136.443894 93.040579) - (xy 136.504237 92.894897) (xy 136.535 92.740242) (xy 136.535 92.683653) (xy 140.5208 92.683653) - (xy 140.5208 92.841346) (xy 140.551561 92.995989) (xy 140.551564 92.996001) (xy 140.611902 93.141672) - (xy 140.611909 93.141685) (xy 140.69951 93.272788) (xy 140.699513 93.272792) (xy 140.811007 93.384286) - (xy 140.811011 93.384289) (xy 140.942114 93.47189) (xy 140.942127 93.471897) (xy 141.087798 93.532235) - (xy 141.087803 93.532237) (xy 141.242453 93.562999) (xy 141.242456 93.563) (xy 141.242458 93.563) - (xy 141.400144 93.563) (xy 141.400145 93.562999) (xy 141.554797 93.532237) (xy 141.696088 93.473713) - (xy 141.700472 93.471897) (xy 141.700472 93.471896) (xy 141.700479 93.471894) (xy 141.831589 93.384289) - (xy 141.943089 93.272789) (xy 142.030694 93.141679) (xy 142.091037 92.995997) (xy 142.108767 92.906863) - (xy 142.113743 92.88185) (xy 142.146128 92.819939) (xy 142.206844 92.785365) (xy 142.276613 92.789104) - (xy 142.333285 92.829971) (xy 142.338462 92.83715) (xy 142.37791 92.896188) (xy 142.377913 92.896192) - (xy 142.489407 93.007686) (xy 142.489411 93.007689) (xy 142.620514 93.09529) (xy 142.620527 93.095297) - (xy 142.766198 93.155635) (xy 142.766203 93.155637) (xy 142.920853 93.186399) (xy 142.920856 93.1864) - (xy 142.920858 93.1864) (xy 143.078544 93.1864) (xy 143.078545 93.186399) (xy 143.233197 93.155637) - (xy 143.378879 93.095294) (xy 143.509989 93.007689) (xy 143.621489 92.896189) (xy 143.709094 92.765079) - (xy 143.769437 92.619397) (xy 143.8002 92.464742) (xy 143.8002 92.307058) (xy 143.8002 92.307055) - (xy 143.800199 92.307053) (xy 143.794203 92.276911) (xy 143.769437 92.152403) (xy 143.739999 92.081332) - (xy 143.709097 92.006727) (xy 143.70909 92.006714) (xy 143.621489 91.875611) (xy 143.621486 91.875607) - (xy 143.509992 91.764113) (xy 143.509988 91.76411) (xy 143.378885 91.676509) (xy 143.378872 91.676502) - (xy 143.233201 91.616164) (xy 143.233189 91.616161) (xy 143.078545 91.5854) (xy 143.078542 91.5854) - (xy 142.920858 91.5854) (xy 142.920855 91.5854) (xy 142.76621 91.616161) (xy 142.766198 91.616164) - (xy 142.620527 91.676502) (xy 142.620514 91.676509) (xy 142.489411 91.76411) (xy 142.489407 91.764113) - (xy 142.377913 91.875607) (xy 142.37791 91.875611) (xy 142.290309 92.006714) (xy 142.290302 92.006727) - (xy 142.229964 92.152398) (xy 142.229961 92.152407) (xy 142.207256 92.266551) (xy 142.17487 92.328461) - (xy 142.114154 92.363035) (xy 142.044385 92.359294) (xy 141.987713 92.318427) (xy 141.982537 92.311248) - (xy 141.943092 92.252215) (xy 141.943086 92.252207) (xy 141.831592 92.140713) (xy 141.831588 92.14071) - (xy 141.700485 92.053109) (xy 141.700472 92.053102) (xy 141.554801 91.992764) (xy 141.554789 91.992761) - (xy 141.400145 91.962) (xy 141.400142 91.962) (xy 141.242458 91.962) (xy 141.242455 91.962) (xy 141.08781 91.992761) - (xy 141.087798 91.992764) (xy 140.942127 92.053102) (xy 140.942114 92.053109) (xy 140.811011 92.14071) - (xy 140.811007 92.140713) (xy 140.699513 92.252207) (xy 140.69951 92.252211) (xy 140.611909 92.383314) - (xy 140.611902 92.383327) (xy 140.551564 92.528998) (xy 140.551561 92.52901) (xy 140.5208 92.683653) - (xy 136.535 92.683653) (xy 136.535 92.582558) (xy 136.535 92.582555) (xy 136.534999 92.582553) (xy 136.529259 92.553698) - (xy 136.504237 92.427903) (xy 136.477368 92.363035) (xy 136.443897 92.282227) (xy 136.44389 92.282214) - (xy 136.356289 92.151111) (xy 136.356286 92.151107) (xy 136.244792 92.039613) (xy 136.244788 92.03961) - (xy 136.113685 91.952009) (xy 136.113672 91.952002) (xy 135.968001 91.891664) (xy 135.967989 91.891661) - (xy 135.813345 91.8609) (xy 135.813342 91.8609) (xy 135.655658 91.8609) (xy 135.655655 91.8609) - (xy 135.50101 91.891661) (xy 135.500998 91.891664) (xy 135.355327 91.952002) (xy 135.355314 91.952009) - (xy 135.224214 92.039608) (xy 135.224206 92.039615) (xy 135.215968 92.047852) (xy 135.154642 92.081332) - (xy 135.084951 92.076342) (xy 135.080842 92.074725) (xy 134.942601 92.017464) (xy 134.942589 92.017461) - (xy 134.787945 91.9867) (xy 134.787942 91.9867) (xy 134.630258 91.9867) (xy 134.630255 91.9867) - (xy 134.47561 92.017461) (xy 134.475598 92.017464) (xy 134.329927 92.077802) (xy 134.329914 92.077809) - (xy 134.198811 92.16541) (xy 134.198807 92.165413) (xy 134.087313 92.276907) (xy 134.08731 92.276911) - (xy 133.999709 92.408014) (xy 133.999702 92.408027) (xy 133.939364 92.553698) (xy 133.939361 92.55371) - (xy 133.9086 92.708353) (xy 128.301373 92.708353) (xy 128.307397 92.678074) (xy 128.307397 92.678073) - (xy 128.326199 92.583546) (xy 128.3262 92.583544) (xy 128.3262 92.425855) (xy 128.326199 92.425853) - (xy 128.317737 92.383314) (xy 128.295437 92.271203) (xy 128.251617 92.165411) (xy 128.235097 92.125527) - (xy 128.23509 92.125514) (xy 128.147489 91.994411) (xy 128.147486 91.994407) (xy 128.035992 91.882913) - (xy 128.035988 91.88291) (xy 127.904885 91.795309) (xy 127.904878 91.795305) (xy 127.891558 91.789788) - (xy 127.884279 91.786773) (xy 127.829876 91.742933) (xy 127.80781 91.676639) (xy 127.825088 91.60894) - (xy 127.876225 91.561329) (xy 127.884257 91.557659) (xy 127.940429 91.534393) (xy 128.071539 91.446788) - (xy 128.183039 91.335288) (xy 128.270644 91.204178) (xy 128.330987 91.058496) (xy 128.36175 90.903841) - (xy 128.36175 90.746157) (xy 128.36175 90.746154) (xy 128.361749 90.746152) (xy 128.330988 90.591509) - (xy 128.330987 90.591502) (xy 128.329807 90.588653) (xy 128.270647 90.445826) (xy 128.27064 90.445813) - (xy 128.183039 90.31471) (xy 128.183036 90.314706) (xy 128.071542 90.203212) (xy 128.071538 90.203209) - (xy 127.944001 90.117991) (xy 127.940433 90.115607) (xy 127.940422 90.115601) (xy 127.794751 90.055263) - (xy 127.794739 90.05526) (xy 127.640095 90.024499) (xy 127.640092 90.024499) (xy 127.482408 90.024499) - (xy 127.482405 90.024499) (xy 127.32776 90.05526) (xy 127.327748 90.055263) (xy 127.182077 90.115601) - (xy 127.182064 90.115608) (xy 127.050961 90.203209) (xy 127.050957 90.203212) (xy 126.939463 90.314706) - (xy 126.93946 90.31471) (xy 126.851859 90.445813) (xy 126.851852 90.445826) (xy 126.791514 90.591497) - (xy 126.791511 90.591509) (xy 126.76075 90.746152) (xy 126.76075 90.903845) (xy 126.791511 91.058488) - (xy 126.791514 91.0585) (xy 126.851852 91.204171) (xy 126.851859 91.204184) (xy 126.93946 91.335287) - (xy 126.939463 91.335291) (xy 127.050957 91.446785) (xy 127.050961 91.446788) (xy 127.182064 91.534389) - (xy 127.182066 91.53439) (xy 127.182071 91.534393) (xy 127.202669 91.542925) (xy 127.257072 91.586763) - (xy 127.279139 91.653056) (xy 127.261862 91.720756) (xy 127.210726 91.768368) (xy 127.202672 91.772047) - (xy 127.146521 91.795306) (xy 127.146514 91.795309) (xy 127.015411 91.88291) (xy 127.015407 91.882913) - (xy 126.903913 91.994407) (xy 126.90391 91.994411) (xy 126.816309 92.125514) (xy 126.816302 92.125527) - (xy 126.755964 92.271198) (xy 126.755961 92.27121) (xy 126.7252 92.425853) (xy 126.7252 92.583546) - (xy 126.753916 92.727909) (xy 126.747689 92.7975) (xy 126.704826 92.852678) (xy 126.638936 92.875922) - (xy 126.632299 92.8761) (xy 126.591255 92.8761) (xy 126.43661 92.906861) (xy 126.436598 92.906864) - (xy 126.290927 92.967202) (xy 126.290914 92.967209) (xy 126.159811 93.05481) (xy 126.159807 93.054813) - (xy 126.048313 93.166307) (xy 126.04831 93.166311) (xy 125.960709 93.297414) (xy 125.960702 93.297427) - (xy 125.900364 93.443098) (xy 125.900361 93.44311) (xy 125.8696 93.597753) (xy 120.2505 93.597753) - (xy 120.2505 90.360753) (xy 122.7573 90.360753) (xy 122.7573 90.518446) (xy 122.788061 90.673089) - (xy 122.788064 90.673101) (xy 122.848402 90.818772) (xy 122.848409 90.818785) (xy 122.93601 90.949888) - (xy 122.936013 90.949892) (xy 123.047507 91.061386) (xy 123.047511 91.061389) (xy 123.178614 91.14899) - (xy 123.178627 91.148997) (xy 123.311831 91.204171) (xy 123.324303 91.209337) (xy 123.478953 91.240099) - (xy 123.478956 91.2401) (xy 123.478958 91.2401) (xy 123.636644 91.2401) (xy 123.636645 91.240099) - (xy 123.791297 91.209337) (xy 123.936979 91.148994) (xy 124.068089 91.061389) (xy 124.179589 90.949889) - (xy 124.267194 90.818779) (xy 124.327537 90.673097) (xy 124.3583 90.518442) (xy 124.3583 90.360758) - (xy 124.3583 90.360755) (xy 124.358299 90.360753) (xy 124.35579 90.348138) (xy 124.327537 90.206103) - (xy 124.316442 90.179317) (xy 124.267197 90.060427) (xy 124.26719 90.060414) (xy 124.179589 89.929311) - (xy 124.179586 89.929307) (xy 124.068092 89.817813) (xy 124.068088 89.81781) (xy 123.936985 89.730209) - (xy 123.936972 89.730202) (xy 123.791301 89.669864) (xy 123.791289 89.669861) (xy 123.636645 89.6391) - (xy 123.636642 89.6391) (xy 123.478958 89.6391) (xy 123.478955 89.6391) (xy 123.32431 89.669861) - (xy 123.324298 89.669864) (xy 123.178627 89.730202) (xy 123.178614 89.730209) (xy 123.047511 89.81781) - (xy 123.047507 89.817813) (xy 122.936013 89.929307) (xy 122.93601 89.929311) (xy 122.848409 90.060414) - (xy 122.848402 90.060427) (xy 122.788064 90.206098) (xy 122.788061 90.20611) (xy 122.7573 90.360753) - (xy 120.2505 90.360753) (xy 120.2505 85.693995) (xy 121.099499 85.693995) (xy 121.126418 85.829322) + (xy 122.481585 121.248444) (xy 122.292179 121.344951) (xy 122.120213 121.46989) (xy 121.96989 121.620213) + (xy 121.844951 121.792179) (xy 121.748444 121.981585) (xy 121.682753 122.18376) (xy 121.660826 122.322203) + (xy 121.6495 122.393713) (xy 120.2505 122.393713) (xy 120.2505 120.611152) (xy 129.379498 120.611152) + (xy 129.379498 120.768845) (xy 129.410259 120.923488) (xy 129.410262 120.9235) (xy 129.4706 121.069171) + (xy 129.470607 121.069184) (xy 129.558208 121.200287) (xy 129.558211 121.200291) (xy 129.669705 121.311785) + (xy 129.669709 121.311788) (xy 129.800812 121.399389) (xy 129.800825 121.399396) (xy 129.946496 121.459734) + (xy 129.946501 121.459736) (xy 130.101151 121.490498) (xy 130.101154 121.490499) (xy 130.101156 121.490499) + (xy 130.258842 121.490499) (xy 130.258843 121.490498) (xy 130.413495 121.459736) (xy 130.559177 121.399393) + (xy 130.690287 121.311788) (xy 130.801787 121.200288) (xy 130.889392 121.069178) (xy 130.949735 120.923496) + (xy 130.980498 120.768841) (xy 130.980498 120.611157) (xy 130.980498 120.611154) (xy 130.980497 120.611152) + (xy 130.949736 120.456509) (xy 130.949735 120.456502) (xy 130.949733 120.456497) (xy 130.889395 120.310826) + (xy 130.889388 120.310813) (xy 130.801787 120.17971) (xy 130.801784 120.179706) (xy 130.69029 120.068212) + (xy 130.690286 120.068209) (xy 130.559183 119.980608) (xy 130.55917 119.980601) (xy 130.413499 119.920263) + (xy 130.413487 119.92026) (xy 130.258843 119.889499) (xy 130.25884 119.889499) (xy 130.101156 119.889499) + (xy 130.101153 119.889499) (xy 129.946508 119.92026) (xy 129.946496 119.920263) (xy 129.800825 119.980601) + (xy 129.800812 119.980608) (xy 129.669709 120.068209) (xy 129.669705 120.068212) (xy 129.558211 120.179706) + (xy 129.558208 120.17971) (xy 129.470607 120.310813) (xy 129.4706 120.310826) (xy 129.410262 120.456497) + (xy 129.410259 120.456509) (xy 129.379498 120.611152) (xy 120.2505 120.611152) (xy 120.2505 119.521153) + (xy 123.1995 119.521153) (xy 123.1995 119.678846) (xy 123.230261 119.833489) (xy 123.230264 119.833501) + (xy 123.290602 119.979172) (xy 123.290609 119.979185) (xy 123.37821 120.110288) (xy 123.378213 120.110292) + (xy 123.489707 120.221786) (xy 123.489711 120.221789) (xy 123.620814 120.30939) (xy 123.620827 120.309397) + (xy 123.766498 120.369735) (xy 123.766503 120.369737) (xy 123.921153 120.400499) (xy 123.921156 120.4005) + (xy 123.921158 120.4005) (xy 124.078844 120.4005) (xy 124.078845 120.400499) (xy 124.233497 120.369737) + (xy 124.375722 120.310826) (xy 124.379172 120.309397) (xy 124.379172 120.309396) (xy 124.379179 120.309394) + (xy 124.510289 120.221789) (xy 124.621789 120.110289) (xy 124.709394 119.979179) (xy 124.769737 119.833497) + (xy 124.8005 119.678842) (xy 124.8005 119.521158) (xy 124.8005 119.521155) (xy 124.800499 119.521153) + (xy 124.769738 119.36651) (xy 124.769737 119.366503) (xy 124.744284 119.305053) (xy 124.709397 119.220827) + (xy 124.70939 119.220814) (xy 124.621789 119.089711) (xy 124.621786 119.089707) (xy 124.510292 118.978213) + (xy 124.510288 118.97821) (xy 124.379185 118.890609) (xy 124.379172 118.890602) (xy 124.233501 118.830264) + (xy 124.233489 118.830261) (xy 124.078845 118.7995) (xy 124.078842 118.7995) (xy 123.921158 118.7995) + (xy 123.921155 118.7995) (xy 123.76651 118.830261) (xy 123.766498 118.830264) (xy 123.620827 118.890602) + (xy 123.620814 118.890609) (xy 123.489711 118.97821) (xy 123.489707 118.978213) (xy 123.378213 119.089707) + (xy 123.37821 119.089711) (xy 123.290609 119.220814) (xy 123.290602 119.220827) (xy 123.230264 119.366498) + (xy 123.230261 119.36651) (xy 123.1995 119.521153) (xy 120.2505 119.521153) (xy 120.2505 117.721153) + (xy 126.9995 117.721153) (xy 126.9995 117.878846) (xy 127.030261 118.033489) (xy 127.030264 118.033501) + (xy 127.090602 118.179172) (xy 127.090609 118.179185) (xy 127.17821 118.310288) (xy 127.178213 118.310292) + (xy 127.289707 118.421786) (xy 127.289711 118.421789) (xy 127.420814 118.50939) (xy 127.420827 118.509397) + (xy 127.566498 118.569735) (xy 127.566503 118.569737) (xy 127.721153 118.600499) (xy 127.721156 118.6005) + (xy 127.721158 118.6005) (xy 127.878844 118.6005) (xy 127.878845 118.600499) (xy 128.033497 118.569737) + (xy 128.179179 118.509394) (xy 128.310289 118.421789) (xy 128.421789 118.310289) (xy 128.509394 118.179179) + (xy 128.511331 118.174504) (xy 128.538301 118.10939) (xy 128.569737 118.033497) (xy 128.6005 117.878842) + (xy 128.6005 117.721158) (xy 128.6005 117.721155) (xy 128.600499 117.721153) (xy 128.584287 117.639649) + (xy 128.569737 117.566503) (xy 128.557901 117.537927) (xy 128.509397 117.420827) (xy 128.50939 117.420814) + (xy 128.421789 117.289711) (xy 128.421786 117.289707) (xy 128.310292 117.178213) (xy 128.310288 117.17821) + (xy 128.179185 117.090609) (xy 128.179172 117.090602) (xy 128.033501 117.030264) (xy 128.033489 117.030261) + (xy 127.878845 116.9995) (xy 127.878842 116.9995) (xy 127.721158 116.9995) (xy 127.721155 116.9995) + (xy 127.56651 117.030261) (xy 127.566498 117.030264) (xy 127.420827 117.090602) (xy 127.420814 117.090609) + (xy 127.289711 117.17821) (xy 127.289707 117.178213) (xy 127.178213 117.289707) (xy 127.17821 117.289711) + (xy 127.090609 117.420814) (xy 127.090602 117.420827) (xy 127.030264 117.566498) (xy 127.030261 117.56651) + (xy 126.9995 117.721153) (xy 120.2505 117.721153) (xy 120.2505 116.521153) (xy 129.4995 116.521153) + (xy 129.4995 116.678846) (xy 129.530261 116.833489) (xy 129.530264 116.833501) (xy 129.590604 116.979176) + (xy 129.626162 117.032392) (xy 129.64704 117.099069) (xy 129.637623 117.148732) (xy 129.630262 117.166502) + (xy 129.630261 117.166505) (xy 129.5995 117.321153) (xy 129.5995 117.478846) (xy 129.630261 117.633489) + (xy 129.630264 117.633501) (xy 129.690602 117.779172) (xy 129.690609 117.779185) (xy 129.77821 117.910288) + (xy 129.778213 117.910292) (xy 129.889707 118.021786) (xy 129.889711 118.021789) (xy 130.020814 118.10939) + (xy 130.020827 118.109397) (xy 130.141028 118.159185) (xy 130.166503 118.169737) (xy 130.321153 118.200499) + (xy 130.321156 118.2005) (xy 130.321158 118.2005) (xy 130.478844 118.2005) (xy 130.478845 118.200499) + (xy 130.633497 118.169737) (xy 130.679457 118.150699) (xy 130.748924 118.14323) (xy 130.811403 118.174504) + (xy 130.847057 118.234592) (xy 130.845697 118.295669) (xy 130.846587 118.295846) (xy 130.845581 118.3009) + (xy 130.845574 118.30124) (xy 130.845399 118.301814) (xy 130.814636 118.456471) (xy 130.814636 118.614164) + (xy 130.845397 118.768807) (xy 130.8454 118.768819) (xy 130.905738 118.91449) (xy 130.905745 118.914503) + (xy 130.993346 119.045606) (xy 130.993349 119.04561) (xy 131.104843 119.157104) (xy 131.104847 119.157107) + (xy 131.23595 119.244708) (xy 131.235963 119.244715) (xy 131.381634 119.305053) (xy 131.381639 119.305055) + (xy 131.536289 119.335817) (xy 131.536292 119.335818) (xy 131.536294 119.335818) (xy 131.69398 119.335818) + (xy 131.693981 119.335817) (xy 131.848633 119.305055) (xy 131.994315 119.244712) (xy 132.125425 119.157107) + (xy 132.236925 119.045607) (xy 132.32453 118.914497) (xy 132.332591 118.895034) (xy 132.376431 118.840631) + (xy 132.442725 118.818565) (xy 132.510425 118.835843) (xy 132.516039 118.839381) (xy 132.620821 118.909394) + (xy 132.620823 118.909395) (xy 132.620827 118.909397) (xy 132.747998 118.962072) (xy 132.766503 118.969737) + (xy 132.854426 118.987226) (xy 132.921153 119.000499) (xy 132.921156 119.0005) (xy 132.921158 119.0005) + (xy 133.078844 119.0005) (xy 133.078845 119.000499) (xy 133.233497 118.969737) (xy 133.379179 118.909394) + (xy 133.38111 118.908103) (xy 133.382276 118.907737) (xy 133.384546 118.906525) (xy 133.384776 118.906955) + (xy 133.447786 118.887226) (xy 133.515166 118.90571) (xy 133.51885 118.908077) (xy 133.520821 118.909394) + (xy 133.520824 118.909395) (xy 133.520827 118.909397) (xy 133.647998 118.962072) (xy 133.666503 118.969737) + (xy 133.754426 118.987226) (xy 133.821153 119.000499) (xy 133.821156 119.0005) (xy 133.821158 119.0005) + (xy 133.978844 119.0005) (xy 133.978845 119.000499) (xy 134.133497 118.969737) (xy 134.279179 118.909394) + (xy 134.410289 118.821789) (xy 134.521789 118.710289) (xy 134.609394 118.579179) (xy 134.610277 118.577048) + (xy 134.611035 118.576106) (xy 134.612264 118.573809) (xy 134.612699 118.574041) (xy 134.654115 118.522646) + (xy 134.720408 118.500579) (xy 134.724838 118.5005) (xy 134.733741 118.5005) (xy 134.80078 118.520185) + (xy 134.846535 118.572989) (xy 134.848302 118.577048) (xy 134.890602 118.679172) (xy 134.890609 118.679185) + (xy 134.97821 118.810288) (xy 134.978213 118.810292) (xy 135.089707 118.921786) (xy 135.089711 118.921789) + (xy 135.220814 119.00939) (xy 135.220827 119.009397) (xy 135.366498 119.069735) (xy 135.366503 119.069737) + (xy 135.521153 119.100499) (xy 135.521156 119.1005) (xy 135.521158 119.1005) (xy 135.678844 119.1005) + (xy 135.678845 119.100499) (xy 135.833497 119.069737) (xy 135.979179 119.009394) (xy 135.98111 119.008103) + (xy 135.982276 119.007737) (xy 135.984546 119.006525) (xy 135.984776 119.006955) (xy 136.047786 118.987226) + (xy 136.115166 119.00571) (xy 136.11885 119.008077) (xy 136.120821 119.009394) (xy 136.120824 119.009395) + (xy 136.120827 119.009397) (xy 136.266498 119.069735) (xy 136.266503 119.069737) (xy 136.421153 119.100499) + (xy 136.421156 119.1005) (xy 136.421158 119.1005) (xy 136.578844 119.1005) (xy 136.578845 119.100499) + (xy 136.733497 119.069737) (xy 136.879179 119.009394) (xy 137.010289 118.921789) (xy 137.121789 118.810289) + (xy 137.209394 118.679179) (xy 137.269737 118.533497) (xy 137.3005 118.378842) (xy 137.3005 118.221158) + (xy 137.3005 118.221155) (xy 137.300499 118.221153) (xy 137.288173 118.159185) (xy 137.269737 118.066503) + (xy 137.247783 118.013501) (xy 137.209397 117.920827) (xy 137.20939 117.920814) (xy 137.121789 117.789711) + (xy 137.121786 117.789707) (xy 137.033232 117.701153) (xy 144.6995 117.701153) (xy 144.6995 117.858846) + (xy 144.730261 118.013489) (xy 144.730264 118.013501) (xy 144.790602 118.159172) (xy 144.790609 118.159185) + (xy 144.87821 118.290288) (xy 144.878213 118.290292) (xy 144.989707 118.401786) (xy 144.989711 118.401789) + (xy 145.120814 118.48939) (xy 145.120827 118.489397) (xy 145.266498 118.549735) (xy 145.266503 118.549737) + (xy 145.388687 118.574041) (xy 145.421153 118.580499) (xy 145.421156 118.5805) (xy 145.421158 118.5805) + (xy 145.578844 118.5805) (xy 145.578845 118.580499) (xy 145.733497 118.549737) (xy 145.852367 118.5005) + (xy 145.879172 118.489397) (xy 145.879172 118.489396) (xy 145.879179 118.489394) (xy 146.010289 118.401789) + (xy 146.121789 118.290289) (xy 146.209394 118.159179) (xy 146.269737 118.013497) (xy 146.3005 117.858842) + (xy 146.3005 117.701158) (xy 146.3005 117.701155) (xy 146.300499 117.701153) (xy 146.295936 117.678213) + (xy 146.269737 117.546503) (xy 146.26301 117.530263) (xy 146.209397 117.400827) (xy 146.20939 117.400814) + (xy 146.121789 117.269711) (xy 146.121786 117.269707) (xy 146.010292 117.158213) (xy 146.010288 117.15821) + (xy 145.879185 117.070609) (xy 145.879172 117.070602) (xy 145.733501 117.010264) (xy 145.733489 117.010261) + (xy 145.578845 116.9795) (xy 145.578842 116.9795) (xy 145.421158 116.9795) (xy 145.421155 116.9795) + (xy 145.26651 117.010261) (xy 145.266498 117.010264) (xy 145.120827 117.070602) (xy 145.120814 117.070609) + (xy 144.989711 117.15821) (xy 144.989707 117.158213) (xy 144.878213 117.269707) (xy 144.87821 117.269711) + (xy 144.790609 117.400814) (xy 144.790602 117.400827) (xy 144.730264 117.546498) (xy 144.730261 117.54651) + (xy 144.6995 117.701153) (xy 137.033232 117.701153) (xy 137.010292 117.678213) (xy 137.010288 117.67821) + (xy 136.879185 117.590609) (xy 136.879172 117.590602) (xy 136.733501 117.530264) (xy 136.733489 117.530261) + (xy 136.578845 117.4995) (xy 136.578842 117.4995) (xy 136.421158 117.4995) (xy 136.421155 117.4995) + (xy 136.26651 117.530261) (xy 136.266498 117.530264) (xy 136.120822 117.590604) (xy 136.12082 117.590605) + (xy 136.118885 117.591899) (xy 136.117717 117.592264) (xy 136.115451 117.593476) (xy 136.115221 117.593045) + (xy 136.052206 117.612773) (xy 135.984827 117.594285) (xy 135.981115 117.591899) (xy 135.979179 117.590605) + (xy 135.979177 117.590604) (xy 135.833501 117.530264) (xy 135.833489 117.530261) (xy 135.678845 117.4995) + (xy 135.678842 117.4995) (xy 135.566259 117.4995) (xy 135.49922 117.479815) (xy 135.453465 117.427011) + (xy 135.451698 117.422952) (xy 135.409397 117.320827) (xy 135.40939 117.320814) (xy 135.321789 117.189711) + (xy 135.321786 117.189707) (xy 135.210292 117.078213) (xy 135.210288 117.07821) (xy 135.079185 116.990609) + (xy 135.079172 116.990602) (xy 134.933501 116.930264) (xy 134.933489 116.930261) (xy 134.778845 116.8995) + (xy 134.778842 116.8995) (xy 134.621158 116.8995) (xy 134.621155 116.8995) (xy 134.46651 116.930261) + (xy 134.466498 116.930264) (xy 134.320827 116.990602) (xy 134.320814 116.990609) (xy 134.189711 117.07821) + (xy 134.189707 117.078213) (xy 134.078213 117.189707) (xy 134.07821 117.189711) (xy 133.990609 117.320814) + (xy 133.990607 117.320819) (xy 133.990606 117.320821) (xy 133.990467 117.321158) (xy 133.989725 117.322949) + (xy 133.988964 117.323893) (xy 133.987736 117.326191) (xy 133.9873 117.325958) (xy 133.945885 117.377354) + (xy 133.879592 117.399421) (xy 133.875162 117.3995) (xy 133.821155 117.3995) (xy 133.66651 117.430261) + (xy 133.666498 117.430264) (xy 133.520822 117.490604) (xy 133.52082 117.490605) (xy 133.518885 117.491899) + (xy 133.517717 117.492264) (xy 133.515451 117.493476) (xy 133.515221 117.493045) (xy 133.452206 117.512773) + (xy 133.384827 117.494285) (xy 133.381115 117.491899) (xy 133.379179 117.490605) (xy 133.379177 117.490604) + (xy 133.233501 117.430264) (xy 133.233489 117.430261) (xy 133.078845 117.3995) (xy 133.078842 117.3995) + (xy 132.921158 117.3995) (xy 132.921155 117.3995) (xy 132.76651 117.430261) (xy 132.766498 117.430264) + (xy 132.620827 117.490602) (xy 132.620814 117.490609) (xy 132.489711 117.57821) (xy 132.489707 117.578213) + (xy 132.378213 117.689707) (xy 132.37821 117.689711) (xy 132.290609 117.820814) (xy 132.290606 117.82082) + (xy 132.282542 117.840288) (xy 132.238699 117.89469) (xy 132.172404 117.916752) (xy 132.104705 117.899471) + (xy 132.099091 117.895933) (xy 131.994321 117.825927) (xy 131.994308 117.82592) (xy 131.848637 117.765582) + (xy 131.848625 117.765579) (xy 131.693981 117.734818) (xy 131.693978 117.734818) (xy 131.536294 117.734818) + (xy 131.536291 117.734818) (xy 131.381646 117.765579) (xy 131.381634 117.765582) (xy 131.335678 117.784618) + (xy 131.266208 117.792087) (xy 131.20373 117.760811) (xy 131.168078 117.700722) (xy 131.169442 117.639649) + (xy 131.168549 117.639472) (xy 131.169559 117.634392) (xy 131.169567 117.634055) (xy 131.169731 117.633511) + (xy 131.169737 117.633497) (xy 131.2005 117.478842) (xy 131.2005 117.321158) (xy 131.2005 117.321155) + (xy 131.200499 117.321153) (xy 131.174353 117.189711) (xy 131.169737 117.166503) (xy 131.137014 117.087502) + (xy 131.109397 117.020827) (xy 131.109395 117.020823) (xy 131.109394 117.020821) (xy 131.081346 116.978844) + (xy 131.073837 116.967606) (xy 131.052959 116.900929) (xy 131.062377 116.851264) (xy 131.069737 116.833497) + (xy 131.072192 116.821153) (xy 138.5995 116.821153) (xy 138.5995 116.978846) (xy 138.630261 117.133489) + (xy 138.630264 117.133501) (xy 138.690602 117.279172) (xy 138.690609 117.279185) (xy 138.77821 117.410288) + (xy 138.778213 117.410292) (xy 138.889707 117.521786) (xy 138.889711 117.521789) (xy 139.020814 117.60939) + (xy 139.020827 117.609397) (xy 139.166498 117.669735) (xy 139.166503 117.669737) (xy 139.321153 117.700499) + (xy 139.321156 117.7005) (xy 139.321158 117.7005) (xy 139.478844 117.7005) (xy 139.478845 117.700499) + (xy 139.633497 117.669737) (xy 139.779179 117.609394) (xy 139.779186 117.609388) (xy 139.77919 117.609387) + (xy 139.805262 117.591966) (xy 139.805266 117.591964) (xy 139.873309 117.546498) (xy 139.910289 117.521789) + (xy 140.021789 117.410289) (xy 140.109394 117.279179) (xy 140.169737 117.133497) (xy 140.2005 116.978842) + (xy 140.2005 116.821158) (xy 140.2005 116.821155) (xy 140.200499 116.821153) (xy 140.172192 116.678846) + (xy 140.169737 116.666503) (xy 140.109534 116.521158) (xy 140.109397 116.520827) (xy 140.10939 116.520814) + (xy 140.021789 116.389711) (xy 140.021786 116.389707) (xy 139.910292 116.278213) (xy 139.910288 116.27821) + (xy 139.779185 116.190609) (xy 139.779172 116.190602) (xy 139.633501 116.130264) (xy 139.633489 116.130261) + (xy 139.478845 116.0995) (xy 139.478842 116.0995) (xy 139.321158 116.0995) (xy 139.321155 116.0995) + (xy 139.16651 116.130261) (xy 139.166498 116.130264) (xy 139.020827 116.190602) (xy 139.020814 116.190609) + (xy 138.889711 116.27821) (xy 138.889707 116.278213) (xy 138.778213 116.389707) (xy 138.77821 116.389711) + (xy 138.690609 116.520814) (xy 138.690602 116.520827) (xy 138.630264 116.666498) (xy 138.630261 116.66651) + (xy 138.5995 116.821153) (xy 131.072192 116.821153) (xy 131.1005 116.678842) (xy 131.1005 116.521158) + (xy 131.1005 116.521155) (xy 131.100499 116.521153) (xy 131.074353 116.389711) (xy 131.069737 116.366503) + (xy 131.069735 116.366498) (xy 131.009397 116.220827) (xy 131.00939 116.220814) (xy 130.921789 116.089711) + (xy 130.921786 116.089707) (xy 130.810292 115.978213) (xy 130.810288 115.97821) (xy 130.679185 115.890609) + (xy 130.679172 115.890602) (xy 130.533501 115.830264) (xy 130.533489 115.830261) (xy 130.378845 115.7995) + (xy 130.378842 115.7995) (xy 130.221158 115.7995) (xy 130.221155 115.7995) (xy 130.06651 115.830261) + (xy 130.066498 115.830264) (xy 129.920827 115.890602) (xy 129.920814 115.890609) (xy 129.789711 115.97821) + (xy 129.789707 115.978213) (xy 129.678213 116.089707) (xy 129.67821 116.089711) (xy 129.590609 116.220814) + (xy 129.590602 116.220827) (xy 129.530264 116.366498) (xy 129.530261 116.36651) (xy 129.4995 116.521153) + (xy 120.2505 116.521153) (xy 120.2505 114.021153) (xy 121.8995 114.021153) (xy 121.8995 114.178846) + (xy 121.930261 114.333489) (xy 121.930264 114.333501) (xy 121.990602 114.479172) (xy 121.990609 114.479185) + (xy 122.07821 114.610288) (xy 122.078213 114.610292) (xy 122.189707 114.721786) (xy 122.189711 114.721789) + (xy 122.320814 114.80939) (xy 122.320827 114.809397) (xy 122.458683 114.866498) (xy 122.466503 114.869737) + (xy 122.621153 114.900499) (xy 122.621156 114.9005) (xy 122.621158 114.9005) (xy 122.778844 114.9005) + (xy 122.778845 114.900499) (xy 122.933497 114.869737) (xy 123.079179 114.809394) (xy 123.210289 114.721789) + (xy 123.321789 114.610289) (xy 123.409394 114.479179) (xy 123.469737 114.333497) (xy 123.5005 114.178842) + (xy 123.5005 114.121153) (xy 129.6995 114.121153) (xy 129.6995 114.278846) (xy 129.730261 114.433489) + (xy 129.730264 114.433501) (xy 129.790602 114.579172) (xy 129.790609 114.579185) (xy 129.87821 114.710288) + (xy 129.878213 114.710292) (xy 129.989707 114.821786) (xy 129.989711 114.821789) (xy 130.120814 114.90939) + (xy 130.120827 114.909397) (xy 130.266498 114.969735) (xy 130.266503 114.969737) (xy 130.396982 114.995691) + (xy 130.421153 115.000499) (xy 130.421156 115.0005) (xy 130.421158 115.0005) (xy 130.578844 115.0005) + (xy 130.578845 115.000499) (xy 130.733497 114.969737) (xy 130.733509 114.969731) (xy 130.739324 114.967969) + (xy 130.740158 114.97072) (xy 130.797359 114.964497) (xy 130.859878 114.995691) (xy 130.895608 115.055734) + (xy 130.8995 115.086555) (xy 130.8995 115.178846) (xy 130.930261 115.333489) (xy 130.930264 115.333501) + (xy 130.990602 115.479172) (xy 130.990609 115.479185) (xy 131.07821 115.610288) (xy 131.078213 115.610292) + (xy 131.189707 115.721786) (xy 131.189711 115.721789) (xy 131.320814 115.80939) (xy 131.320827 115.809397) + (xy 131.466498 115.869735) (xy 131.466503 115.869737) (xy 131.621153 115.900499) (xy 131.621156 115.9005) + (xy 131.621158 115.9005) (xy 131.778844 115.9005) (xy 131.778845 115.900499) (xy 131.933497 115.869737) + (xy 132.079179 115.809394) (xy 132.210289 115.721789) (xy 132.321789 115.610289) (xy 132.409394 115.479179) + (xy 132.469737 115.333497) (xy 132.5005 115.178842) (xy 132.5005 115.021158) (xy 132.5005 115.021155) + (xy 132.500499 115.021153) (xy 132.478269 114.909397) (xy 132.469737 114.866503) (xy 132.409794 114.721786) + (xy 132.409397 114.720827) (xy 132.40939 114.720814) (xy 132.321789 114.589711) (xy 132.321786 114.589707) + (xy 132.210292 114.478213) (xy 132.210288 114.47821) (xy 132.079185 114.390609) (xy 132.079172 114.390602) + (xy 131.933501 114.330264) (xy 131.933489 114.330261) (xy 131.778845 114.2995) (xy 131.778842 114.2995) + (xy 131.621158 114.2995) (xy 131.621155 114.2995) (xy 131.46651 114.330261) (xy 131.460676 114.332031) + (xy 131.459873 114.329385) (xy 131.402056 114.335396) (xy 131.339687 114.303902) (xy 131.304245 114.243689) + (xy 131.3005 114.213444) (xy 131.3005 114.121155) (xy 131.300499 114.121153) (xy 131.269737 113.966503) + (xy 131.228314 113.866498) (xy 131.209397 113.820827) (xy 131.20939 113.820814) (xy 131.121789 113.689711) + (xy 131.121786 113.689707) (xy 131.010292 113.578213) (xy 131.010288 113.57821) (xy 130.879185 113.490609) + (xy 130.879172 113.490602) (xy 130.733501 113.430264) (xy 130.733489 113.430261) (xy 130.578845 113.3995) + (xy 130.578842 113.3995) (xy 130.421158 113.3995) (xy 130.421155 113.3995) (xy 130.26651 113.430261) + (xy 130.266498 113.430264) (xy 130.120827 113.490602) (xy 130.120814 113.490609) (xy 129.989711 113.57821) + (xy 129.989707 113.578213) (xy 129.878213 113.689707) (xy 129.87821 113.689711) (xy 129.790609 113.820814) + (xy 129.790602 113.820827) (xy 129.730264 113.966498) (xy 129.730261 113.96651) (xy 129.6995 114.121153) + (xy 123.5005 114.121153) (xy 123.5005 114.021158) (xy 123.5005 114.021155) (xy 123.500499 114.021153) + (xy 123.469738 113.86651) (xy 123.469737 113.866503) (xy 123.450812 113.820814) (xy 123.409397 113.720827) + (xy 123.40939 113.720814) (xy 123.321789 113.589711) (xy 123.321786 113.589707) (xy 123.210292 113.478213) + (xy 123.210288 113.47821) (xy 123.079185 113.390609) (xy 123.079172 113.390602) (xy 122.933501 113.330264) + (xy 122.933489 113.330261) (xy 122.778845 113.2995) (xy 122.778842 113.2995) (xy 122.621158 113.2995) + (xy 122.621155 113.2995) (xy 122.46651 113.330261) (xy 122.466498 113.330264) (xy 122.320827 113.390602) + (xy 122.320814 113.390609) (xy 122.189711 113.47821) (xy 122.189707 113.478213) (xy 122.078213 113.589707) + (xy 122.07821 113.589711) (xy 121.990609 113.720814) (xy 121.990602 113.720827) (xy 121.930264 113.866498) + (xy 121.930261 113.86651) (xy 121.8995 114.021153) (xy 120.2505 114.021153) (xy 120.2505 111.521153) + (xy 123.3995 111.521153) (xy 123.3995 111.678846) (xy 123.430261 111.833489) (xy 123.430264 111.833501) + (xy 123.490602 111.979172) (xy 123.490609 111.979185) (xy 123.57821 112.110288) (xy 123.578213 112.110292) + (xy 123.689707 112.221786) (xy 123.689711 112.221789) (xy 123.820814 112.30939) (xy 123.820827 112.309397) + (xy 123.966498 112.369735) (xy 123.966503 112.369737) (xy 124.121153 112.400499) (xy 124.121156 112.4005) + (xy 124.121158 112.4005) (xy 124.278844 112.4005) (xy 124.278845 112.400499) (xy 124.433497 112.369737) + (xy 124.579179 112.309394) (xy 124.710289 112.221789) (xy 124.821789 112.110289) (xy 124.909394 111.979179) + (xy 124.969737 111.833497) (xy 125.0005 111.678842) (xy 125.0005 111.521158) (xy 125.0005 111.521155) + (xy 125.000499 111.521153) (xy 124.980734 111.421789) (xy 124.969737 111.366503) (xy 124.946452 111.310288) + (xy 124.909397 111.220827) (xy 124.90939 111.220814) (xy 124.821789 111.089711) (xy 124.821786 111.089707) + (xy 124.710292 110.978213) (xy 124.710288 110.97821) (xy 124.579185 110.890609) (xy 124.579172 110.890602) + (xy 124.458154 110.840475) (xy 124.458147 110.840473) (xy 124.433497 110.830263) (xy 124.278842 110.7995) + (xy 124.121158 110.7995) (xy 124.121155 110.7995) (xy 123.96651 110.830261) (xy 123.966498 110.830264) + (xy 123.820827 110.890602) (xy 123.820814 110.890609) (xy 123.689711 110.97821) (xy 123.689707 110.978213) + (xy 123.578213 111.089707) (xy 123.57821 111.089711) (xy 123.490609 111.220814) (xy 123.490602 111.220827) + (xy 123.430264 111.366498) (xy 123.430261 111.36651) (xy 123.3995 111.521153) (xy 120.2505 111.521153) + (xy 120.2505 109.721153) (xy 123.7995 109.721153) (xy 123.7995 109.878846) (xy 123.830261 110.033489) + (xy 123.830264 110.033501) (xy 123.890602 110.179172) (xy 123.890609 110.179185) (xy 123.97821 110.310288) + (xy 123.978213 110.310292) (xy 124.089707 110.421786) (xy 124.089711 110.421789) (xy 124.220814 110.50939) + (xy 124.220827 110.509397) (xy 124.341844 110.559523) (xy 124.366503 110.569737) (xy 124.521158 110.6005) + (xy 124.521249 110.6005) (xy 124.678844 110.6005) (xy 124.678845 110.600499) (xy 124.833497 110.569737) + (xy 124.979179 110.509394) (xy 125.110289 110.421789) (xy 125.170144 110.361933) (xy 125.231463 110.32845) + (xy 125.301155 110.333434) (xy 125.326714 110.346514) (xy 125.420814 110.40939) (xy 125.420827 110.409397) + (xy 125.566498 110.469735) (xy 125.566503 110.469737) (xy 125.721153 110.500499) (xy 125.721156 110.5005) + (xy 125.721158 110.5005) (xy 125.878844 110.5005) (xy 125.878845 110.500499) (xy 126.033497 110.469737) + (xy 126.151592 110.420821) (xy 126.179172 110.409397) (xy 126.179172 110.409396) (xy 126.179179 110.409394) + (xy 126.310289 110.321789) (xy 126.421789 110.210289) (xy 126.509394 110.079179) (xy 126.569737 109.933497) + (xy 126.592083 109.821158) (xy 126.592084 109.821153) (xy 129.5995 109.821153) (xy 129.5995 109.978846) + (xy 129.630261 110.133489) (xy 129.630264 110.133501) (xy 129.690602 110.279172) (xy 129.690612 110.27919) + (xy 129.751732 110.370663) (xy 129.77261 110.43734) (xy 129.763192 110.487004) (xy 129.730262 110.566506) + (xy 129.73026 110.566511) (xy 129.6995 110.721153) (xy 129.6995 110.878846) (xy 129.730261 111.033489) + (xy 129.730264 111.033501) (xy 129.790602 111.179172) (xy 129.790609 111.179185) (xy 129.87821 111.310288) + (xy 129.878213 111.310292) (xy 129.989707 111.421786) (xy 129.989711 111.421789) (xy 130.120814 111.50939) + (xy 130.120827 111.509397) (xy 130.266498 111.569735) (xy 130.266503 111.569737) (xy 130.421153 111.600499) + (xy 130.421156 111.6005) (xy 130.421158 111.6005) (xy 130.578844 111.6005) (xy 130.578845 111.600499) + (xy 130.733497 111.569737) (xy 130.879179 111.509394) (xy 131.010289 111.421789) (xy 131.121789 111.310289) + (xy 131.209394 111.179179) (xy 131.269737 111.033497) (xy 131.3005 110.878842) (xy 131.3005 110.721158) + (xy 131.3005 110.721155) (xy 131.300499 110.721153) (xy 131.27038 110.569735) (xy 131.269737 110.566503) + (xy 131.242398 110.5005) (xy 131.209397 110.420827) (xy 131.20939 110.420814) (xy 131.148267 110.329337) + (xy 131.127389 110.262659) (xy 131.136808 110.212993) (xy 131.137928 110.210289) (xy 131.169737 110.133497) + (xy 131.2005 109.978842) (xy 131.2005 109.821158) (xy 131.2005 109.821155) (xy 131.176982 109.702925) + (xy 131.183209 109.633333) (xy 131.226072 109.578156) (xy 131.229675 109.575653) (xy 131.310289 109.521789) + (xy 131.421789 109.410289) (xy 131.509394 109.279179) (xy 131.533429 109.221153) (xy 146.4995 109.221153) + (xy 146.4995 109.378846) (xy 146.530261 109.533489) (xy 146.530264 109.533501) (xy 146.590602 109.679172) + (xy 146.590609 109.679185) (xy 146.67821 109.810288) (xy 146.678213 109.810292) (xy 146.789707 109.921786) + (xy 146.789711 109.921789) (xy 146.920814 110.00939) (xy 146.920827 110.009397) (xy 147.066498 110.069735) + (xy 147.066503 110.069737) (xy 147.221153 110.100499) (xy 147.221156 110.1005) (xy 147.221158 110.1005) + (xy 147.378844 110.1005) (xy 147.378845 110.100499) (xy 147.533497 110.069737) (xy 147.679179 110.009394) + (xy 147.810289 109.921789) (xy 147.921789 109.810289) (xy 148.009394 109.679179) (xy 148.069737 109.533497) + (xy 148.1005 109.378842) (xy 148.1005 109.221158) (xy 148.1005 109.221155) (xy 148.100499 109.221153) + (xy 148.074531 109.090606) (xy 148.069737 109.066503) (xy 148.069735 109.066498) (xy 148.009397 108.920827) + (xy 148.00939 108.920814) (xy 147.921789 108.789711) (xy 147.921786 108.789707) (xy 147.810292 108.678213) + (xy 147.810288 108.67821) (xy 147.679185 108.590609) (xy 147.679172 108.590602) (xy 147.533501 108.530264) + (xy 147.533489 108.530261) (xy 147.378845 108.4995) (xy 147.378842 108.4995) (xy 147.221158 108.4995) + (xy 147.221155 108.4995) (xy 147.06651 108.530261) (xy 147.066498 108.530264) (xy 146.920827 108.590602) + (xy 146.920814 108.590609) (xy 146.789711 108.67821) (xy 146.789707 108.678213) (xy 146.678213 108.789707) + (xy 146.67821 108.789711) (xy 146.590609 108.920814) (xy 146.590602 108.920827) (xy 146.530264 109.066498) + (xy 146.530261 109.06651) (xy 146.4995 109.221153) (xy 131.533429 109.221153) (xy 131.569737 109.133497) + (xy 131.6005 108.978842) (xy 131.6005 108.821158) (xy 131.6005 108.821155) (xy 131.600499 108.821153) + (xy 131.594244 108.789707) (xy 131.569737 108.666503) (xy 131.527049 108.563446) (xy 131.519581 108.493978) + (xy 131.532264 108.457521) (xy 131.533649 108.454928) (xy 131.533659 108.454914) (xy 131.594002 108.309232) + (xy 131.611522 108.221153) (xy 144.0995 108.221153) (xy 144.0995 108.378846) (xy 144.130261 108.533489) + (xy 144.130264 108.533501) (xy 144.190602 108.679172) (xy 144.190609 108.679185) (xy 144.27821 108.810288) + (xy 144.278213 108.810292) (xy 144.389707 108.921786) (xy 144.389711 108.921789) (xy 144.520814 109.00939) + (xy 144.520827 109.009397) (xy 144.658683 109.066498) (xy 144.666503 109.069737) (xy 144.821153 109.100499) + (xy 144.821156 109.1005) (xy 144.821158 109.1005) (xy 144.978844 109.1005) (xy 144.978845 109.100499) + (xy 144.996061 109.097075) (xy 145.014287 109.09345) (xy 145.014292 109.093449) (xy 145.0998 109.076439) + (xy 145.133497 109.069737) (xy 145.279179 109.009394) (xy 145.410289 108.921789) (xy 145.521789 108.810289) + (xy 145.609394 108.679179) (xy 145.669737 108.533497) (xy 145.7005 108.378842) (xy 145.7005 108.378835) + (xy 145.701097 108.372782) (xy 145.703484 108.373017) (xy 145.720185 108.316141) (xy 145.755606 108.28008) + (xy 145.821888 108.235793) (xy 145.933388 108.124293) (xy 146.020993 107.993183) (xy 146.081336 107.847501) + (xy 146.112099 107.692846) (xy 146.112099 107.535162) (xy 146.112099 107.535159) (xy 146.112098 107.535157) + (xy 146.095944 107.453945) (xy 146.081336 107.380507) (xy 146.075467 107.366337) (xy 146.020996 107.234831) + (xy 146.020989 107.234818) (xy 145.933388 107.103715) (xy 145.933385 107.103711) (xy 145.821891 106.992217) + (xy 145.821887 106.992214) (xy 145.690784 106.904613) (xy 145.690771 106.904606) (xy 145.5451 106.844268) + (xy 145.545088 106.844265) (xy 145.390444 106.813504) (xy 145.390441 106.813504) (xy 145.232757 106.813504) + (xy 145.232754 106.813504) (xy 145.078109 106.844265) (xy 145.078097 106.844268) (xy 144.932426 106.904606) + (xy 144.932413 106.904613) (xy 144.80131 106.992214) (xy 144.801306 106.992217) (xy 144.689812 107.103711) + (xy 144.689809 107.103715) (xy 144.602208 107.234818) (xy 144.602201 107.234831) (xy 144.541863 107.380502) + (xy 144.54186 107.380514) (xy 144.511099 107.535157) (xy 144.510502 107.541222) (xy 144.508114 107.540986) + (xy 144.491414 107.597861) (xy 144.45599 107.633924) (xy 144.389711 107.67821) (xy 144.389707 107.678213) + (xy 144.278213 107.789707) (xy 144.27821 107.789711) (xy 144.190609 107.920814) (xy 144.190602 107.920827) + (xy 144.130264 108.066498) (xy 144.130261 108.06651) (xy 144.0995 108.221153) (xy 131.611522 108.221153) + (xy 131.624765 108.154577) (xy 131.624765 107.996893) (xy 131.624765 107.99689) (xy 131.624764 107.996888) + (xy 131.598308 107.863886) (xy 131.594002 107.842238) (xy 131.58077 107.810292) (xy 131.533662 107.696562) + (xy 131.533655 107.696549) (xy 131.446054 107.565446) (xy 131.446051 107.565442) (xy 131.334557 107.453948) + (xy 131.334553 107.453945) (xy 131.20345 107.366344) (xy 131.203437 107.366337) (xy 131.057766 107.305999) + (xy 131.057754 107.305996) (xy 130.90311 107.275235) (xy 130.903107 107.275235) (xy 130.745423 107.275235) + (xy 130.74542 107.275235) (xy 130.590775 107.305996) (xy 130.590763 107.305999) (xy 130.445092 107.366337) + (xy 130.445079 107.366344) (xy 130.313976 107.453945) (xy 130.313972 107.453948) (xy 130.202478 107.565442) + (xy 130.202475 107.565446) (xy 130.114874 107.696549) (xy 130.114867 107.696562) (xy 130.054529 107.842233) + (xy 130.054526 107.842245) (xy 130.023765 107.996888) (xy 130.023765 108.154581) (xy 130.054526 108.309224) + (xy 130.054529 108.309236) (xy 130.097213 108.412286) (xy 130.104682 108.481756) (xy 130.09202 108.518173) + (xy 130.090608 108.520815) (xy 130.030264 108.666498) (xy 130.030261 108.66651) (xy 129.9995 108.821153) + (xy 129.9995 108.978846) (xy 130.023017 109.097075) (xy 130.01679 109.166667) (xy 129.973927 109.221844) + (xy 129.970291 109.224368) (xy 129.889711 109.27821) (xy 129.889707 109.278213) (xy 129.778213 109.389707) + (xy 129.77821 109.389711) (xy 129.690609 109.520814) (xy 129.690602 109.520827) (xy 129.630264 109.666498) + (xy 129.630261 109.66651) (xy 129.5995 109.821153) (xy 126.592084 109.821153) (xy 126.598107 109.790875) + (xy 126.598107 109.790874) (xy 126.6005 109.778844) (xy 126.6005 109.621155) (xy 126.600499 109.621153) + (xy 126.580734 109.521789) (xy 126.569737 109.466503) (xy 126.537929 109.389711) (xy 126.509397 109.320827) + (xy 126.50939 109.320814) (xy 126.421789 109.189711) (xy 126.421786 109.189707) (xy 126.310292 109.078213) + (xy 126.310288 109.07821) (xy 126.179185 108.990609) (xy 126.179172 108.990602) (xy 126.033501 108.930264) + (xy 126.033489 108.930261) (xy 125.878845 108.8995) (xy 125.878842 108.8995) (xy 125.721158 108.8995) + (xy 125.721155 108.8995) (xy 125.56651 108.930261) (xy 125.566498 108.930264) (xy 125.420827 108.990602) + (xy 125.420814 108.990609) (xy 125.289711 109.07821) (xy 125.289707 109.078213) (xy 125.229857 109.138064) + (xy 125.168534 109.171549) (xy 125.098842 109.166565) (xy 125.073285 109.153485) (xy 124.979185 109.090609) + (xy 124.979172 109.090602) (xy 124.833501 109.030264) (xy 124.833489 109.030261) (xy 124.678845 108.9995) + (xy 124.678842 108.9995) (xy 124.521158 108.9995) (xy 124.521155 108.9995) (xy 124.36651 109.030261) + (xy 124.366498 109.030264) (xy 124.220827 109.090602) (xy 124.220814 109.090609) (xy 124.089711 109.17821) + (xy 124.089707 109.178213) (xy 123.978213 109.289707) (xy 123.97821 109.289711) (xy 123.890609 109.420814) + (xy 123.890602 109.420827) (xy 123.830264 109.566498) (xy 123.830261 109.56651) (xy 123.7995 109.721153) + (xy 120.2505 109.721153) (xy 120.2505 106.98454) (xy 121.07343 106.98454) (xy 121.07343 107.142233) + (xy 121.104191 107.296876) (xy 121.104194 107.296888) (xy 121.164532 107.442559) (xy 121.164539 107.442572) + (xy 121.25214 107.573675) (xy 121.252143 107.573679) (xy 121.363637 107.685173) (xy 121.363641 107.685176) + (xy 121.494744 107.772777) (xy 121.494757 107.772784) (xy 121.585311 107.810292) (xy 121.640433 107.833124) + (xy 121.795083 107.863886) (xy 121.795086 107.863887) (xy 121.795088 107.863887) (xy 121.952774 107.863887) + (xy 121.952775 107.863886) (xy 122.107427 107.833124) (xy 122.253109 107.772781) (xy 122.384219 107.685176) + (xy 122.495719 107.573676) (xy 122.583324 107.442566) (xy 122.643667 107.296884) (xy 122.67443 107.142229) + (xy 122.67443 106.984545) (xy 122.67443 106.984542) (xy 122.674429 106.98454) (xy 122.66182 106.921153) + (xy 122.643667 106.82989) (xy 122.598102 106.719887) (xy 122.590634 106.650419) (xy 122.601294 106.619772) + (xy 122.600963 106.619635) (xy 122.655955 106.48687) (xy 122.663637 106.468324) (xy 122.692911 106.321153) + (xy 125.5195 106.321153) (xy 125.5195 106.478846) (xy 125.550261 106.633489) (xy 125.550264 106.633501) + (xy 125.610602 106.779172) (xy 125.610609 106.779185) (xy 125.69821 106.910288) (xy 125.698213 106.910292) + (xy 125.809707 107.021786) (xy 125.809711 107.021789) (xy 125.940814 107.10939) (xy 125.940827 107.109397) + (xy 126.086498 107.169735) (xy 126.086503 107.169737) (xy 126.220662 107.196423) (xy 126.241153 107.200499) + (xy 126.241156 107.2005) (xy 126.241158 107.2005) (xy 126.398844 107.2005) (xy 126.398845 107.200499) + (xy 126.553497 107.169737) (xy 126.699179 107.109394) (xy 126.830289 107.021789) (xy 126.930925 106.921153) + (xy 132.2995 106.921153) (xy 132.2995 107.078846) (xy 132.330261 107.233489) (xy 132.330264 107.233501) + (xy 132.390602 107.379172) (xy 132.390609 107.379185) (xy 132.47821 107.510288) (xy 132.478213 107.510292) + (xy 132.589707 107.621786) (xy 132.589711 107.621789) (xy 132.720814 107.70939) (xy 132.720827 107.709397) + (xy 132.866498 107.769735) (xy 132.866503 107.769737) (xy 133.021153 107.800499) (xy 133.021156 107.8005) + (xy 133.021158 107.8005) (xy 133.178844 107.8005) (xy 133.178845 107.800499) (xy 133.333497 107.769737) + (xy 133.479179 107.709394) (xy 133.610289 107.621789) (xy 133.721789 107.510289) (xy 133.809394 107.379179) + (xy 133.86256 107.250822) (xy 133.906398 107.196423) (xy 133.972691 107.174357) (xy 134.001311 107.176661) + (xy 134.121155 107.2005) (xy 134.121158 107.2005) (xy 134.278844 107.2005) (xy 134.278845 107.200499) + (xy 134.433497 107.169737) (xy 134.579179 107.109394) (xy 134.710289 107.021789) (xy 134.821789 106.910289) + (xy 134.909394 106.779179) (xy 134.969737 106.633497) (xy 135.0005 106.478842) (xy 135.0005 106.321158) + (xy 135.0005 106.321155) (xy 135.000499 106.321153) (xy 134.994422 106.290602) (xy 134.969737 106.166503) + (xy 134.968084 106.162512) (xy 134.950953 106.121153) (xy 138.0995 106.121153) (xy 138.0995 106.278846) + (xy 138.130261 106.433489) (xy 138.130264 106.433501) (xy 138.190602 106.579172) (xy 138.190609 106.579185) + (xy 138.27821 106.710288) (xy 138.278213 106.710292) (xy 138.389707 106.821786) (xy 138.389711 106.821789) + (xy 138.520814 106.90939) (xy 138.520827 106.909397) (xy 138.656158 106.965452) (xy 138.666503 106.969737) + (xy 138.779502 106.992214) (xy 138.821153 107.000499) (xy 138.821156 107.0005) (xy 138.821158 107.0005) + (xy 138.978844 107.0005) (xy 138.978845 107.000499) (xy 139.133497 106.969737) (xy 139.201315 106.941645) + (xy 139.270782 106.934177) (xy 139.333261 106.965452) (xy 139.336447 106.968526) (xy 139.389707 107.021786) + (xy 139.389711 107.021789) (xy 139.520814 107.10939) (xy 139.520827 107.109397) (xy 139.666498 107.169735) + (xy 139.666503 107.169737) (xy 139.800662 107.196423) (xy 139.821153 107.200499) (xy 139.821156 107.2005) + (xy 139.821158 107.2005) (xy 139.978844 107.2005) (xy 139.978845 107.200499) (xy 140.133497 107.169737) + (xy 140.279179 107.109394) (xy 140.410289 107.021789) (xy 140.428606 107.003472) (xy 140.489928 106.969985) + (xy 140.55962 106.974968) (xy 140.615554 107.016838) (xy 140.619391 107.02226) (xy 140.67821 107.110288) + (xy 140.678213 107.110292) (xy 140.789707 107.221786) (xy 140.789711 107.221789) (xy 140.920814 107.30939) + (xy 140.920827 107.309397) (xy 141.030082 107.354651) (xy 141.066503 107.369737) (xy 141.121831 107.380742) + (xy 141.18374 107.413126) (xy 141.218315 107.473841) (xy 141.219256 107.478166) (xy 141.230261 107.533492) + (xy 141.230264 107.533501) (xy 141.290602 107.679172) (xy 141.290609 107.679185) (xy 141.37821 107.810288) + (xy 141.378213 107.810292) (xy 141.489707 107.921786) (xy 141.489711 107.921789) (xy 141.620814 108.00939) + (xy 141.620827 108.009397) (xy 141.758683 108.066498) (xy 141.766503 108.069737) (xy 141.921153 108.100499) + (xy 141.921156 108.1005) (xy 141.921158 108.1005) (xy 142.078844 108.1005) (xy 142.078845 108.100499) + (xy 142.089179 108.098443) (xy 142.114287 108.09345) (xy 142.114292 108.093449) (xy 142.1998 108.076439) + (xy 142.233497 108.069737) (xy 142.379179 108.009394) (xy 142.510289 107.921789) (xy 142.621789 107.810289) + (xy 142.709394 107.679179) (xy 142.769737 107.533497) (xy 142.8005 107.378842) (xy 142.8005 107.221158) + (xy 142.8005 107.221155) (xy 142.800499 107.221153) (xy 142.778447 107.110292) (xy 142.769737 107.066503) + (xy 142.742398 107.0005) (xy 142.709397 106.920827) (xy 142.70939 106.920814) (xy 142.621789 106.789711) + (xy 142.621786 106.789707) (xy 142.510292 106.678213) (xy 142.510288 106.67821) (xy 142.379185 106.590609) + (xy 142.379172 106.590602) (xy 142.233501 106.530264) (xy 142.233492 106.530261) (xy 142.178166 106.519256) + (xy 142.116256 106.48687) (xy 142.081682 106.426154) (xy 142.08075 106.421874) (xy 142.069737 106.366503) + (xy 142.047854 106.313673) (xy 142.009397 106.220827) (xy 142.00939 106.220814) (xy 141.921789 106.089711) + (xy 141.921786 106.089707) (xy 141.810292 105.978213) (xy 141.810288 105.97821) (xy 141.679185 105.890609) + (xy 141.679172 105.890602) (xy 141.533501 105.830264) (xy 141.533489 105.830261) (xy 141.378845 105.7995) + (xy 141.378842 105.7995) (xy 141.221158 105.7995) (xy 141.221155 105.7995) (xy 141.06651 105.830261) + (xy 141.066498 105.830264) (xy 140.920827 105.890602) (xy 140.920814 105.890609) (xy 140.789711 105.97821) + (xy 140.789706 105.978214) (xy 140.771389 105.996531) (xy 140.710065 106.030015) (xy 140.640374 106.025029) + (xy 140.584441 105.983156) (xy 140.580608 105.977739) (xy 140.521789 105.889711) (xy 140.521786 105.889707) + (xy 140.410292 105.778213) (xy 140.410288 105.77821) (xy 140.279185 105.690609) (xy 140.279172 105.690602) + (xy 140.133501 105.630264) (xy 140.133489 105.630261) (xy 139.978845 105.5995) (xy 139.978842 105.5995) + (xy 139.821158 105.5995) (xy 139.821155 105.5995) (xy 139.666505 105.630261) (xy 139.666497 105.630264) + (xy 139.598682 105.658353) (xy 139.529213 105.66582) (xy 139.466734 105.634544) (xy 139.463551 105.631472) + (xy 139.410292 105.578213) (xy 139.410288 105.57821) (xy 139.279185 105.490609) (xy 139.279172 105.490602) + (xy 139.133501 105.430264) (xy 139.133489 105.430261) (xy 138.978845 105.3995) (xy 138.978842 105.3995) + (xy 138.821158 105.3995) (xy 138.821155 105.3995) (xy 138.66651 105.430261) (xy 138.666498 105.430264) + (xy 138.520827 105.490602) (xy 138.520814 105.490609) (xy 138.389711 105.57821) (xy 138.389707 105.578213) + (xy 138.278213 105.689707) (xy 138.27821 105.689711) (xy 138.190609 105.820814) (xy 138.190602 105.820827) + (xy 138.130264 105.966498) (xy 138.130261 105.96651) (xy 138.0995 106.121153) (xy 134.950953 106.121153) + (xy 134.909397 106.020827) (xy 134.90939 106.020814) (xy 134.821789 105.889711) (xy 134.821786 105.889707) + (xy 134.710292 105.778213) (xy 134.710288 105.77821) (xy 134.579185 105.690609) (xy 134.579172 105.690602) + (xy 134.433501 105.630264) (xy 134.433489 105.630261) (xy 134.278845 105.5995) (xy 134.278842 105.5995) + (xy 134.121158 105.5995) (xy 134.121155 105.5995) (xy 133.96651 105.630261) (xy 133.966498 105.630264) + (xy 133.820827 105.690602) (xy 133.820814 105.690609) (xy 133.689711 105.77821) (xy 133.689707 105.778213) + (xy 133.578213 105.889707) (xy 133.57821 105.889711) (xy 133.490609 106.020814) (xy 133.490604 106.020824) + (xy 133.43744 106.149174) (xy 133.393599 106.203577) (xy 133.327305 106.225642) (xy 133.298688 106.223338) + (xy 133.178846 106.1995) (xy 133.178842 106.1995) (xy 133.021158 106.1995) (xy 133.021155 106.1995) + (xy 132.86651 106.230261) (xy 132.866498 106.230264) (xy 132.720827 106.290602) (xy 132.720814 106.290609) + (xy 132.589711 106.37821) (xy 132.589707 106.378213) (xy 132.478213 106.489707) (xy 132.47821 106.489711) + (xy 132.390609 106.620814) (xy 132.390602 106.620827) (xy 132.330264 106.766498) (xy 132.330261 106.76651) + (xy 132.2995 106.921153) (xy 126.930925 106.921153) (xy 126.941789 106.910289) (xy 126.995506 106.829897) + (xy 127.02939 106.779185) (xy 127.02939 106.779184) (xy 127.029394 106.779179) (xy 127.089737 106.633497) + (xy 127.1205 106.478842) (xy 127.1205 106.321158) (xy 127.1205 106.321155) (xy 127.120499 106.321153) + (xy 127.114422 106.290602) (xy 127.089737 106.166503) (xy 127.088084 106.162512) (xy 127.029397 106.020827) + (xy 127.02939 106.020814) (xy 126.941789 105.889711) (xy 126.941786 105.889707) (xy 126.830292 105.778213) + (xy 126.830288 105.77821) (xy 126.699185 105.690609) (xy 126.699172 105.690602) (xy 126.553501 105.630264) + (xy 126.553489 105.630261) (xy 126.398845 105.5995) (xy 126.398842 105.5995) (xy 126.241158 105.5995) + (xy 126.241155 105.5995) (xy 126.08651 105.630261) (xy 126.086498 105.630264) (xy 125.940827 105.690602) + (xy 125.940814 105.690609) (xy 125.809711 105.77821) (xy 125.809707 105.778213) (xy 125.698213 105.889707) + (xy 125.69821 105.889711) (xy 125.610609 106.020814) (xy 125.610602 106.020827) (xy 125.550264 106.166498) + (xy 125.550261 106.16651) (xy 125.5195 106.321153) (xy 122.692911 106.321153) (xy 122.6944 106.313669) + (xy 122.6944 106.155985) (xy 122.6944 106.155982) (xy 122.694399 106.15598) (xy 122.681216 106.089707) + (xy 122.663637 106.00133) (xy 122.654061 105.978211) (xy 122.603297 105.855654) (xy 122.60329 105.855641) + (xy 122.515689 105.724538) (xy 122.515686 105.724534) (xy 122.404192 105.61304) (xy 122.404188 105.613037) + (xy 122.273085 105.525436) (xy 122.273072 105.525429) (xy 122.162498 105.479629) (xy 122.127397 105.46509) + (xy 122.127389 105.465088) (xy 121.972745 105.434327) (xy 121.972742 105.434327) (xy 121.815058 105.434327) + (xy 121.815055 105.434327) (xy 121.66041 105.465088) (xy 121.660398 105.465091) (xy 121.514727 105.525429) + (xy 121.514714 105.525436) (xy 121.383611 105.613037) (xy 121.383607 105.61304) (xy 121.272113 105.724534) + (xy 121.27211 105.724538) (xy 121.184509 105.855641) (xy 121.184502 105.855654) (xy 121.124164 106.001325) + (xy 121.124161 106.001337) (xy 121.0934 106.15598) (xy 121.0934 106.313673) (xy 121.124161 106.468316) + (xy 121.124164 106.468328) (xy 121.169726 106.578325) (xy 121.177195 106.647794) (xy 121.166538 106.678443) + (xy 121.166867 106.67858) (xy 121.104194 106.829885) (xy 121.104191 106.829897) (xy 121.07343 106.98454) + (xy 120.2505 106.98454) (xy 120.2505 105.371155) (xy 127.3995 105.371155) (xy 127.3995 105.528848) + (xy 127.430261 105.683491) (xy 127.430264 105.683503) (xy 127.490602 105.829174) (xy 127.490609 105.829187) + (xy 127.57821 105.96029) (xy 127.578213 105.960294) (xy 127.689707 106.071788) (xy 127.689711 106.071791) + (xy 127.820814 106.159392) (xy 127.820827 106.159399) (xy 127.917641 106.1995) (xy 127.966503 106.219739) + (xy 128.121153 106.250501) (xy 128.121156 106.250502) (xy 128.121158 106.250502) (xy 128.278844 106.250502) + (xy 128.278845 106.250501) (xy 128.433497 106.219739) (xy 128.562033 106.166498) (xy 128.579172 106.159399) + (xy 128.579172 106.159398) (xy 128.579179 106.159396) (xy 128.710289 106.071791) (xy 128.821789 105.960291) + (xy 128.909394 105.829181) (xy 128.969737 105.683499) (xy 129.0005 105.528844) (xy 129.0005 105.37116) + (xy 129.0005 105.371157) (xy 129.000499 105.371155) (xy 128.969738 105.216512) (xy 128.969737 105.216505) + (xy 128.969735 105.2165) (xy 128.909397 105.070829) (xy 128.90939 105.070816) (xy 128.821789 104.939713) + (xy 128.821786 104.939709) (xy 128.710292 104.828215) (xy 128.710288 104.828212) (xy 128.579185 104.740611) + (xy 128.579172 104.740604) (xy 128.433501 104.680266) (xy 128.433489 104.680263) (xy 128.278845 104.649502) + (xy 128.278842 104.649502) (xy 128.121158 104.649502) (xy 128.121155 104.649502) (xy 127.96651 104.680263) + (xy 127.966498 104.680266) (xy 127.820827 104.740604) (xy 127.820814 104.740611) (xy 127.689711 104.828212) + (xy 127.689707 104.828215) (xy 127.578213 104.939709) (xy 127.57821 104.939713) (xy 127.490609 105.070816) + (xy 127.490602 105.070829) (xy 127.430264 105.2165) (xy 127.430261 105.216512) (xy 127.3995 105.371155) + (xy 120.2505 105.371155) (xy 120.2505 104.044681) (xy 124.1495 104.044681) (xy 124.1495 104.202374) + (xy 124.180261 104.357017) (xy 124.180264 104.357029) (xy 124.240602 104.5027) (xy 124.240609 104.502713) + (xy 124.32821 104.633816) (xy 124.328213 104.63382) (xy 124.439707 104.745314) (xy 124.439711 104.745317) + (xy 124.570814 104.832918) (xy 124.570827 104.832925) (xy 124.716498 104.893263) (xy 124.716503 104.893265) + (xy 124.871153 104.924027) (xy 124.871156 104.924028) (xy 124.871158 104.924028) (xy 125.028844 104.924028) + (xy 125.028845 104.924027) (xy 125.183497 104.893265) (xy 125.329179 104.832922) (xy 125.460289 104.745317) + (xy 125.571789 104.633817) (xy 125.659394 104.502707) (xy 125.719737 104.357025) (xy 125.7505 104.20237) + (xy 125.7505 104.098089) (xy 140.26761 104.098089) (xy 140.26761 104.255782) (xy 140.298371 104.410425) + (xy 140.298374 104.410437) (xy 140.358712 104.556108) (xy 140.358719 104.556121) (xy 140.44632 104.687224) + (xy 140.446323 104.687228) (xy 140.557817 104.798722) (xy 140.557821 104.798725) (xy 140.688924 104.886326) + (xy 140.688937 104.886333) (xy 140.8178 104.939709) (xy 140.834613 104.946673) (xy 140.989263 104.977435) + (xy 140.989266 104.977436) (xy 140.989268 104.977436) (xy 141.146954 104.977436) (xy 141.146955 104.977435) + (xy 141.301607 104.946673) (xy 141.447289 104.88633) (xy 141.578399 104.798725) (xy 141.689899 104.687225) + (xy 141.777504 104.556115) (xy 141.837847 104.410433) (xy 141.86861 104.255778) (xy 141.86861 104.098094) + (xy 141.86861 104.098091) (xy 141.868609 104.098089) (xy 141.837848 103.943446) (xy 141.837847 103.943439) + (xy 141.815723 103.890026) (xy 141.777507 103.797763) (xy 141.7775 103.79775) (xy 141.689899 103.666647) + (xy 141.689896 103.666643) (xy 141.578402 103.555149) (xy 141.578398 103.555146) (xy 141.447295 103.467545) + (xy 141.447282 103.467538) (xy 141.301611 103.4072) (xy 141.301599 103.407197) (xy 141.146955 103.376436) + (xy 141.146952 103.376436) (xy 140.989268 103.376436) (xy 140.989265 103.376436) (xy 140.83462 103.407197) + (xy 140.834608 103.4072) (xy 140.688937 103.467538) (xy 140.688924 103.467545) (xy 140.557821 103.555146) + (xy 140.557817 103.555149) (xy 140.446323 103.666643) (xy 140.44632 103.666647) (xy 140.358719 103.79775) + (xy 140.358712 103.797763) (xy 140.298374 103.943434) (xy 140.298371 103.943446) (xy 140.26761 104.098089) + (xy 125.7505 104.098089) (xy 125.7505 104.044686) (xy 125.7505 104.044683) (xy 125.750499 104.044681) + (xy 125.730362 103.943446) (xy 125.719737 103.890031) (xy 125.681519 103.797763) (xy 125.659397 103.744355) + (xy 125.65939 103.744342) (xy 125.571789 103.613239) (xy 125.571786 103.613235) (xy 125.460292 103.501741) + (xy 125.460288 103.501738) (xy 125.329185 103.414137) (xy 125.329172 103.41413) (xy 125.183501 103.353792) + (xy 125.183489 103.353789) (xy 125.028845 103.323028) (xy 125.028842 103.323028) (xy 124.871158 103.323028) + (xy 124.871155 103.323028) (xy 124.71651 103.353789) (xy 124.716498 103.353792) (xy 124.570827 103.41413) + (xy 124.570814 103.414137) (xy 124.439711 103.501738) (xy 124.439707 103.501741) (xy 124.328213 103.613235) + (xy 124.32821 103.613239) (xy 124.240609 103.744342) (xy 124.240602 103.744355) (xy 124.180264 103.890026) + (xy 124.180261 103.890038) (xy 124.1495 104.044681) (xy 120.2505 104.044681) (xy 120.2505 102.721153) + (xy 121.4995 102.721153) (xy 121.4995 102.878846) (xy 121.530261 103.033489) (xy 121.530264 103.033501) + (xy 121.590602 103.179172) (xy 121.590609 103.179185) (xy 121.67821 103.310288) (xy 121.678213 103.310292) + (xy 121.789707 103.421786) (xy 121.789711 103.421789) (xy 121.920814 103.50939) (xy 121.920827 103.509397) + (xy 122.031277 103.555146) (xy 122.066503 103.569737) (xy 122.221153 103.600499) (xy 122.221156 103.6005) + (xy 122.221158 103.6005) (xy 122.378844 103.6005) (xy 122.378845 103.600499) (xy 122.533497 103.569737) + (xy 122.679179 103.509394) (xy 122.810289 103.421789) (xy 122.921789 103.310289) (xy 123.009394 103.179179) + (xy 123.069737 103.033497) (xy 123.1005 102.878842) (xy 123.1005 102.721158) (xy 123.1005 102.721155) + (xy 123.100499 102.721153) (xy 123.069738 102.56651) (xy 123.069737 102.566503) (xy 123.033427 102.478842) + (xy 123.009397 102.420827) (xy 123.00939 102.420814) (xy 122.984763 102.383957) (xy 122.942798 102.321153) + (xy 141.7995 102.321153) (xy 141.7995 102.478846) (xy 141.830261 102.633489) (xy 141.830264 102.633501) + (xy 141.890602 102.779172) (xy 141.890609 102.779185) (xy 141.97821 102.910288) (xy 141.978213 102.910292) + (xy 142.089707 103.021786) (xy 142.089711 103.021789) (xy 142.220814 103.10939) (xy 142.220827 103.109397) + (xy 142.366498 103.169735) (xy 142.366503 103.169737) (xy 142.521153 103.200499) (xy 142.521156 103.2005) + (xy 142.521158 103.2005) (xy 142.678844 103.2005) (xy 142.678845 103.200499) (xy 142.833497 103.169737) + (xy 142.979179 103.109394) (xy 143.110289 103.021789) (xy 143.221789 102.910289) (xy 143.309394 102.779179) + (xy 143.369737 102.633497) (xy 143.4005 102.478842) (xy 143.4005 102.321158) (xy 143.4005 102.321155) + (xy 143.400499 102.321153) (xy 143.372066 102.178211) (xy 143.369737 102.166503) (xy 143.338298 102.090602) + (xy 143.309397 102.020827) (xy 143.30939 102.020814) (xy 143.221789 101.889711) (xy 143.221786 101.889707) + (xy 143.110292 101.778213) (xy 143.110288 101.77821) (xy 142.979185 101.690609) (xy 142.979172 101.690602) + (xy 142.833501 101.630264) (xy 142.833489 101.630261) (xy 142.678845 101.5995) (xy 142.678842 101.5995) + (xy 142.521158 101.5995) (xy 142.521155 101.5995) (xy 142.36651 101.630261) (xy 142.366498 101.630264) + (xy 142.220827 101.690602) (xy 142.220814 101.690609) (xy 142.089711 101.77821) (xy 142.089707 101.778213) + (xy 141.978213 101.889707) (xy 141.97821 101.889711) (xy 141.890609 102.020814) (xy 141.890602 102.020827) + (xy 141.830264 102.166498) (xy 141.830261 102.16651) (xy 141.7995 102.321153) (xy 122.942798 102.321153) + (xy 122.921789 102.289711) (xy 122.921786 102.289707) (xy 122.810292 102.178213) (xy 122.810288 102.17821) + (xy 122.679185 102.090609) (xy 122.679172 102.090602) (xy 122.533501 102.030264) (xy 122.533489 102.030261) + (xy 122.378845 101.9995) (xy 122.378842 101.9995) (xy 122.221158 101.9995) (xy 122.221155 101.9995) + (xy 122.06651 102.030261) (xy 122.066498 102.030264) (xy 121.920827 102.090602) (xy 121.920814 102.090609) + (xy 121.789711 102.17821) (xy 121.789707 102.178213) (xy 121.678213 102.289707) (xy 121.67821 102.289711) + (xy 121.590609 102.420814) (xy 121.590602 102.420827) (xy 121.530264 102.566498) (xy 121.530261 102.56651) + (xy 121.4995 102.721153) (xy 120.2505 102.721153) (xy 120.2505 100.321153) (xy 125.7995 100.321153) + (xy 125.7995 100.478846) (xy 125.830261 100.633489) (xy 125.830264 100.633501) (xy 125.890602 100.779172) + (xy 125.890609 100.779185) (xy 125.97821 100.910288) (xy 125.978213 100.910292) (xy 126.089707 101.021786) + (xy 126.089711 101.021789) (xy 126.220814 101.10939) (xy 126.220827 101.109397) (xy 126.366498 101.169735) + (xy 126.366503 101.169737) (xy 126.521153 101.200499) (xy 126.521156 101.2005) (xy 126.521158 101.2005) + (xy 126.678844 101.2005) (xy 126.678845 101.200499) (xy 126.833497 101.169737) (xy 126.979179 101.109394) + (xy 127.110289 101.021789) (xy 127.110925 101.021153) (xy 130.2995 101.021153) (xy 130.2995 101.178846) + (xy 130.330261 101.333489) (xy 130.330264 101.333501) (xy 130.390602 101.479172) (xy 130.390609 101.479185) + (xy 130.47821 101.610288) (xy 130.478213 101.610292) (xy 130.589707 101.721786) (xy 130.589711 101.721789) + (xy 130.720814 101.80939) (xy 130.720827 101.809397) (xy 130.813129 101.847629) (xy 130.866503 101.869737) + (xy 131.021153 101.900499) (xy 131.021156 101.9005) (xy 131.021158 101.9005) (xy 131.178844 101.9005) + (xy 131.178845 101.900499) (xy 131.333497 101.869737) (xy 131.479179 101.809394) (xy 131.610289 101.721789) + (xy 131.721789 101.610289) (xy 131.809394 101.479179) (xy 131.869737 101.333497) (xy 131.9005 101.178842) + (xy 131.9005 101.021158) (xy 131.9005 101.021155) (xy 131.900499 101.021153) (xy 131.878447 100.910292) + (xy 131.869737 100.866503) (xy 131.851215 100.821786) (xy 131.826666 100.762518) (xy 131.809532 100.721153) + (xy 132.4995 100.721153) (xy 132.4995 100.878846) (xy 132.530261 101.033489) (xy 132.530264 101.033501) + (xy 132.590602 101.179172) (xy 132.590609 101.179185) (xy 132.67821 101.310288) (xy 132.678213 101.310292) + (xy 132.789707 101.421786) (xy 132.789711 101.421789) (xy 132.920814 101.50939) (xy 132.920827 101.509397) + (xy 133.066498 101.569735) (xy 133.066503 101.569737) (xy 133.216131 101.5995) (xy 133.221153 101.600499) + (xy 133.221156 101.6005) (xy 133.221158 101.6005) (xy 133.378844 101.6005) (xy 133.378845 101.600499) + (xy 133.533497 101.569737) (xy 133.679179 101.509394) (xy 133.810289 101.421789) (xy 133.921789 101.310289) + (xy 134.009394 101.179179) (xy 134.069737 101.033497) (xy 134.1005 100.878842) (xy 134.1005 100.721158) + (xy 134.1005 100.721155) (xy 134.100499 100.721153) (xy 134.074353 100.589711) (xy 134.069737 100.566503) + (xy 134.049003 100.516446) (xy 134.009397 100.420827) (xy 134.00939 100.420814) (xy 133.921789 100.289711) + (xy 133.921786 100.289707) (xy 133.810292 100.178213) (xy 133.810288 100.17821) (xy 133.679185 100.090609) + (xy 133.679172 100.090602) (xy 133.533501 100.030264) (xy 133.533489 100.030261) (xy 133.378845 99.9995) + (xy 133.378842 99.9995) (xy 133.221158 99.9995) (xy 133.221155 99.9995) (xy 133.06651 100.030261) + (xy 133.066498 100.030264) (xy 132.920827 100.090602) (xy 132.920814 100.090609) (xy 132.789711 100.17821) + (xy 132.789707 100.178213) (xy 132.678213 100.289707) (xy 132.67821 100.289711) (xy 132.590609 100.420814) + (xy 132.590602 100.420827) (xy 132.530264 100.566498) (xy 132.530261 100.56651) (xy 132.4995 100.721153) + (xy 131.809532 100.721153) (xy 131.809395 100.720823) (xy 131.80939 100.720814) (xy 131.721789 100.589711) + (xy 131.721786 100.589707) (xy 131.610292 100.478213) (xy 131.610288 100.47821) (xy 131.479185 100.390609) + (xy 131.479172 100.390602) (xy 131.333501 100.330264) (xy 131.333489 100.330261) (xy 131.178845 100.2995) + (xy 131.178842 100.2995) (xy 131.021158 100.2995) (xy 131.021155 100.2995) (xy 130.86651 100.330261) + (xy 130.866498 100.330264) (xy 130.720827 100.390602) (xy 130.720814 100.390609) (xy 130.589711 100.47821) + (xy 130.589707 100.478213) (xy 130.478213 100.589707) (xy 130.47821 100.589711) (xy 130.390609 100.720814) + (xy 130.390602 100.720827) (xy 130.330264 100.866498) (xy 130.330261 100.86651) (xy 130.2995 101.021153) + (xy 127.110925 101.021153) (xy 127.131579 101.000499) (xy 127.204694 100.927385) (xy 127.221786 100.910292) + (xy 127.221789 100.910289) (xy 127.309394 100.779179) (xy 127.369737 100.633497) (xy 127.4005 100.478842) + (xy 127.4005 100.321158) (xy 127.4005 100.321155) (xy 127.400499 100.321153) (xy 127.394244 100.289707) + (xy 127.369737 100.166503) (xy 127.350955 100.121158) (xy 127.309397 100.020827) (xy 127.309393 100.02082) + (xy 127.309389 100.020814) (xy 127.2888 99.99) (xy 127.267923 99.923324) (xy 127.286407 99.855944) + (xy 127.338386 99.809253) (xy 127.407356 99.798077) (xy 127.416084 99.79949) (xy 127.421158 99.8005) + (xy 127.42116 99.8005) (xy 127.578844 99.8005) (xy 127.578845 99.800499) (xy 127.733497 99.769737) + (xy 127.879179 99.709394) (xy 128.010289 99.621789) (xy 128.121789 99.510289) (xy 128.209394 99.379179) + (xy 128.269737 99.233497) (xy 128.3005 99.078842) (xy 128.3005 98.921158) (xy 128.3005 98.921155) + (xy 128.300499 98.921153) (xy 135.0995 98.921153) (xy 135.0995 99.078846) (xy 135.130261 99.233489) + (xy 135.130264 99.233501) (xy 135.190602 99.379172) (xy 135.190609 99.379184) (xy 135.23157 99.440486) + (xy 135.252448 99.507163) (xy 135.243809 99.552726) (xy 135.244053 99.552801) (xy 135.243365 99.555068) + (xy 135.243033 99.55682) (xy 135.242287 99.55862) (xy 135.242283 99.558632) (xy 135.211523 99.713274) + (xy 135.211523 99.870967) (xy 135.242284 100.02561) (xy 135.242287 100.025622) (xy 135.302625 100.171293) + (xy 135.302632 100.171306) (xy 135.390233 100.302409) (xy 135.390236 100.302413) (xy 135.50173 100.413907) + (xy 135.501736 100.413912) (xy 135.527333 100.431016) (xy 135.572138 100.484629) (xy 135.580844 100.553954) + (xy 135.550688 100.616981) (xy 135.546126 100.621794) (xy 135.53998 100.627939) (xy 135.539975 100.627946) + (xy 135.452374 100.759049) (xy 135.452367 100.759062) (xy 135.392029 100.904733) (xy 135.392026 100.904745) + (xy 135.361265 101.059388) (xy 135.361265 101.217081) (xy 135.392026 101.371724) (xy 135.392029 101.371736) + (xy 135.452367 101.517407) (xy 135.452374 101.51742) (xy 135.539975 101.648523) (xy 135.539978 101.648527) + (xy 135.651472 101.760021) (xy 135.651476 101.760024) (xy 135.782579 101.847625) (xy 135.782592 101.847632) + (xy 135.910226 101.900499) (xy 135.928268 101.907972) (xy 136.082918 101.938734) (xy 136.082921 101.938735) + (xy 136.082923 101.938735) (xy 136.240609 101.938735) (xy 136.24061 101.938734) (xy 136.395262 101.907972) + (xy 136.540944 101.847629) (xy 136.672054 101.760024) (xy 136.783554 101.648524) (xy 136.871159 101.517414) + (xy 136.931502 101.371732) (xy 136.962265 101.217077) (xy 136.962265 101.070718) (xy 136.98195 101.003679) + (xy 137.034754 100.957924) (xy 137.103912 100.94798) (xy 137.133717 100.956157) (xy 137.166498 100.969735) + (xy 137.166503 100.969737) (xy 137.321153 101.000499) (xy 137.321156 101.0005) (xy 137.321158 101.0005) + (xy 137.478844 101.0005) (xy 137.478845 101.000499) (xy 137.633497 100.969737) (xy 137.779179 100.909394) + (xy 137.910289 100.821789) (xy 138.021789 100.710289) (xy 138.109394 100.579179) (xy 138.169737 100.433497) + (xy 138.2005 100.278842) (xy 138.2005 100.121158) (xy 138.2005 100.121155) (xy 138.200499 100.121153) + (xy 138.182419 100.030261) (xy 138.169737 99.966503) (xy 138.137929 99.889711) (xy 138.109397 99.820827) + (xy 138.10939 99.820814) (xy 138.021789 99.689711) (xy 138.021786 99.689707) (xy 137.910292 99.578213) + (xy 137.910288 99.57821) (xy 137.779185 99.490609) (xy 137.779172 99.490602) (xy 137.633501 99.430264) + (xy 137.633489 99.430261) (xy 137.478845 99.3995) (xy 137.478842 99.3995) (xy 137.321158 99.3995) + (xy 137.321155 99.3995) (xy 137.16651 99.430261) (xy 137.166498 99.430264) (xy 137.020827 99.490602) + (xy 137.020814 99.490609) (xy 136.937146 99.546515) (xy 136.870468 99.567393) (xy 136.803088 99.548908) + (xy 136.756398 99.496929) (xy 136.753694 99.490865) (xy 136.721419 99.412946) (xy 136.721418 99.412945) + (xy 136.721417 99.412942) (xy 136.680451 99.351633) (xy 136.659574 99.284958) (xy 136.668216 99.239403) + (xy 136.667968 99.239328) (xy 136.668668 99.237019) (xy 136.668998 99.23528) (xy 136.669737 99.233497) + (xy 136.7005 99.078842) (xy 136.7005 98.921158) (xy 136.7005 98.921155) (xy 136.700499 98.921153) + (xy 136.689455 98.865633) (xy 136.669737 98.766503) (xy 136.628328 98.666531) (xy 136.609397 98.620827) + (xy 136.60939 98.620814) (xy 136.521789 98.489711) (xy 136.521786 98.489707) (xy 136.410292 98.378213) + (xy 136.410288 98.37821) (xy 136.279185 98.290609) (xy 136.279172 98.290602) (xy 136.19263 98.254756) + (xy 136.133501 98.230264) (xy 136.133489 98.230261) (xy 135.978845 98.1995) (xy 135.978842 98.1995) + (xy 135.821158 98.1995) (xy 135.821155 98.1995) (xy 135.66651 98.230261) (xy 135.666498 98.230264) + (xy 135.520827 98.290602) (xy 135.520814 98.290609) (xy 135.389711 98.37821) (xy 135.389707 98.378213) + (xy 135.278213 98.489707) (xy 135.27821 98.489711) (xy 135.190609 98.620814) (xy 135.190602 98.620827) + (xy 135.130264 98.766498) (xy 135.130261 98.76651) (xy 135.0995 98.921153) (xy 128.300499 98.921153) + (xy 128.289455 98.865633) (xy 128.269737 98.766503) (xy 128.228328 98.666531) (xy 128.209397 98.620827) + (xy 128.20939 98.620814) (xy 128.121789 98.489711) (xy 128.121786 98.489707) (xy 128.010292 98.378213) + (xy 128.010288 98.37821) (xy 127.879185 98.290609) (xy 127.879172 98.290602) (xy 127.733501 98.230264) + (xy 127.733489 98.230261) (xy 127.578845 98.1995) (xy 127.578842 98.1995) (xy 127.421158 98.1995) + (xy 127.421155 98.1995) (xy 127.26651 98.230261) (xy 127.266498 98.230264) (xy 127.120827 98.290602) + (xy 127.120814 98.290609) (xy 126.989711 98.37821) (xy 126.989707 98.378213) (xy 126.878213 98.489707) + (xy 126.87821 98.489711) (xy 126.790609 98.620814) (xy 126.790602 98.620827) (xy 126.730264 98.766498) + (xy 126.730261 98.76651) (xy 126.6995 98.921153) (xy 126.6995 99.078846) (xy 126.730261 99.233489) + (xy 126.730264 99.233501) (xy 126.790602 99.379172) (xy 126.790609 99.379185) (xy 126.811198 99.409998) + (xy 126.832076 99.476676) (xy 126.813592 99.544056) (xy 126.761613 99.590746) (xy 126.692643 99.601922) + (xy 126.683909 99.600507) (xy 126.678846 99.5995) (xy 126.678842 99.5995) (xy 126.521158 99.5995) + (xy 126.521155 99.5995) (xy 126.36651 99.630261) (xy 126.366498 99.630264) (xy 126.220827 99.690602) + (xy 126.220814 99.690609) (xy 126.089711 99.77821) (xy 126.089707 99.778213) (xy 125.978213 99.889707) + (xy 125.97821 99.889711) (xy 125.890609 100.020814) (xy 125.890602 100.020827) (xy 125.830264 100.166498) + (xy 125.830261 100.16651) (xy 125.7995 100.321153) (xy 120.2505 100.321153) (xy 120.2505 98.021153) + (xy 123.0995 98.021153) (xy 123.0995 98.178846) (xy 123.130261 98.333489) (xy 123.130264 98.333501) + (xy 123.190602 98.479172) (xy 123.190609 98.479185) (xy 123.27821 98.610288) (xy 123.278213 98.610292) + (xy 123.389707 98.721786) (xy 123.389711 98.721789) (xy 123.520814 98.80939) (xy 123.520827 98.809397) + (xy 123.656585 98.865629) (xy 123.666503 98.869737) (xy 123.821153 98.900499) (xy 123.821156 98.9005) + (xy 123.821158 98.9005) (xy 123.978844 98.9005) (xy 123.978845 98.900499) (xy 124.133497 98.869737) + (xy 124.279179 98.809394) (xy 124.410289 98.721789) (xy 124.521789 98.610289) (xy 124.609394 98.479179) + (xy 124.669737 98.333497) (xy 124.7005 98.178842) (xy 124.7005 98.021158) (xy 124.7005 98.021155) + (xy 124.700499 98.021153) (xy 124.680925 97.922749) (xy 124.669737 97.866503) (xy 124.661221 97.845943) + (xy 124.609397 97.720827) (xy 124.60939 97.720814) (xy 124.521789 97.589711) (xy 124.521786 97.589707) + (xy 124.410289 97.47821) (xy 124.280149 97.391253) (xy 125.3495 97.391253) (xy 125.3495 97.548946) + (xy 125.380261 97.703589) (xy 125.380264 97.703601) (xy 125.440602 97.849272) (xy 125.440609 97.849285) + (xy 125.52821 97.980388) (xy 125.528213 97.980392) (xy 125.639707 98.091886) (xy 125.639711 98.091889) + (xy 125.770814 98.17949) (xy 125.770827 98.179497) (xy 125.916498 98.239835) (xy 125.916503 98.239837) + (xy 126.071153 98.270599) (xy 126.071156 98.2706) (xy 126.071158 98.2706) (xy 126.228844 98.2706) + (xy 126.228845 98.270599) (xy 126.383497 98.239837) (xy 126.529179 98.179494) (xy 126.578884 98.146282) + (xy 139.085387 98.146282) (xy 139.085387 98.303975) (xy 139.116148 98.458618) (xy 139.116151 98.45863) + (xy 139.176489 98.604301) (xy 139.176496 98.604314) (xy 139.264097 98.735417) (xy 139.2641 98.735421) + (xy 139.375594 98.846915) (xy 139.375598 98.846918) (xy 139.506701 98.934519) (xy 139.506714 98.934526) + (xy 139.614532 98.979185) (xy 139.65239 98.994866) (xy 139.80704 99.025628) (xy 139.807043 99.025629) + (xy 139.807045 99.025629) (xy 139.964731 99.025629) (xy 139.964732 99.025628) (xy 140.119384 98.994866) + (xy 140.265066 98.934523) (xy 140.396176 98.846918) (xy 140.507676 98.735418) (xy 140.595281 98.604308) + (xy 140.655624 98.458626) (xy 140.686387 98.303971) (xy 140.686387 98.146287) (xy 140.686387 98.146284) + (xy 140.686386 98.146282) (xy 140.676285 98.095496) (xy 140.672684 98.077392) (xy 146.233858 98.077392) + (xy 146.233858 98.235085) (xy 146.264619 98.389728) (xy 146.264622 98.38974) (xy 146.32496 98.535411) + (xy 146.324967 98.535424) (xy 146.412568 98.666527) (xy 146.412571 98.666531) (xy 146.524065 98.778025) + (xy 146.524069 98.778028) (xy 146.655172 98.865629) (xy 146.655185 98.865636) (xy 146.789217 98.921153) + (xy 146.800861 98.925976) (xy 146.860027 98.937745) (xy 146.928316 98.951329) (xy 146.990227 98.983714) + (xy 147.007227 99.004055) (xy 147.07821 99.110288) (xy 147.078213 99.110292) (xy 147.189707 99.221786) + (xy 147.189711 99.221789) (xy 147.320814 99.30939) (xy 147.320827 99.309397) (xy 147.466498 99.369735) + (xy 147.466503 99.369737) (xy 147.616131 99.3995) (xy 147.621153 99.400499) (xy 147.621156 99.4005) + (xy 147.621158 99.4005) (xy 147.778844 99.4005) (xy 147.778845 99.400499) (xy 147.933497 99.369737) + (xy 148.079179 99.309394) (xy 148.210289 99.221789) (xy 148.321789 99.110289) (xy 148.409394 98.979179) + (xy 148.469737 98.833497) (xy 148.5005 98.678842) (xy 148.5005 98.521158) (xy 148.5005 98.521155) + (xy 148.500499 98.521153) (xy 148.488062 98.45863) (xy 148.469737 98.366503) (xy 148.456062 98.333489) + (xy 148.409397 98.220827) (xy 148.40939 98.220814) (xy 148.321789 98.089711) (xy 148.321786 98.089707) + (xy 148.210292 97.978213) (xy 148.210288 97.97821) (xy 148.079185 97.890609) (xy 148.079172 97.890602) + (xy 147.933501 97.830264) (xy 147.933491 97.830261) (xy 147.80604 97.804909) (xy 147.744129 97.772524) + (xy 147.72713 97.752183) (xy 147.656147 97.64595) (xy 147.656144 97.645946) (xy 147.54465 97.534452) + (xy 147.544646 97.534449) (xy 147.413543 97.446848) (xy 147.41353 97.446841) (xy 147.267859 97.386503) + (xy 147.267847 97.3865) (xy 147.113203 97.355739) (xy 147.1132 97.355739) (xy 146.955516 97.355739) + (xy 146.955513 97.355739) (xy 146.800868 97.3865) (xy 146.800856 97.386503) (xy 146.655185 97.446841) + (xy 146.655172 97.446848) (xy 146.524069 97.534449) (xy 146.524065 97.534452) (xy 146.412571 97.645946) + (xy 146.412568 97.64595) (xy 146.324967 97.777053) (xy 146.32496 97.777066) (xy 146.264622 97.922737) + (xy 146.264619 97.922749) (xy 146.233858 98.077392) (xy 140.672684 98.077392) (xy 140.655625 97.991637) + (xy 140.655624 97.991636) (xy 140.655624 97.991632) (xy 140.650065 97.978211) (xy 140.595284 97.845956) + (xy 140.595277 97.845943) (xy 140.507676 97.71484) (xy 140.507673 97.714836) (xy 140.396179 97.603342) + (xy 140.396175 97.603339) (xy 140.265072 97.515738) (xy 140.265059 97.515731) (xy 140.119388 97.455393) + (xy 140.119376 97.45539) (xy 139.964732 97.424629) (xy 139.964729 97.424629) (xy 139.807045 97.424629) + (xy 139.807042 97.424629) (xy 139.652397 97.45539) (xy 139.652385 97.455393) (xy 139.506714 97.515731) + (xy 139.506701 97.515738) (xy 139.375598 97.603339) (xy 139.375594 97.603342) (xy 139.2641 97.714836) + (xy 139.264097 97.71484) (xy 139.176496 97.845943) (xy 139.176489 97.845956) (xy 139.116151 97.991627) + (xy 139.116148 97.991639) (xy 139.085387 98.146282) (xy 126.578884 98.146282) (xy 126.660289 98.091889) + (xy 126.771789 97.980389) (xy 126.859394 97.849279) (xy 126.860771 97.845956) (xy 126.873067 97.816266) + (xy 126.919737 97.703597) (xy 126.9505 97.548942) (xy 126.9505 97.391258) (xy 126.9505 97.391255) + (xy 126.933062 97.303591) (xy 128.40854 97.303591) (xy 128.442112 97.326023) (xy 128.560401 97.37502) + (xy 128.560409 97.375022) (xy 128.685976 97.399999) (xy 128.68598 97.4) (xy 128.81402 97.4) (xy 128.814023 97.399999) + (xy 128.93959 97.375022) (xy 128.939594 97.375021) (xy 129.057891 97.32602) (xy 129.057898 97.326016) + (xy 129.091458 97.303591) (xy 129.091459 97.30359) (xy 128.750001 96.962132) (xy 128.75 96.962132) + (xy 128.40854 97.303591) (xy 126.933062 97.303591) (xy 126.928682 97.281572) (xy 126.928682 97.281571) + (xy 126.919738 97.23661) (xy 126.919737 97.236603) (xy 126.859617 97.091459) (xy 126.859397 97.090927) + (xy 126.85939 97.090914) (xy 126.771789 96.959811) (xy 126.771786 96.959807) (xy 126.660292 96.848313) + (xy 126.660288 96.84831) (xy 126.562532 96.782991) (xy 126.529185 96.760709) (xy 126.529172 96.760702) + (xy 126.383501 96.700364) (xy 126.383489 96.700361) (xy 126.311172 96.685976) (xy 128.1 96.685976) + (xy 128.1 96.814023) (xy 128.124977 96.93959) (xy 128.124979 96.939598) (xy 128.173976 97.057886) + (xy 128.173981 97.057896) (xy 128.196407 97.091458) (xy 128.196408 97.091458) (xy 128.537868 96.75) + (xy 128.537868 96.749999) (xy 128.517978 96.730109) (xy 128.65 96.730109) (xy 128.65 96.769891) + (xy 128.665224 96.806645) (xy 128.693355 96.834776) (xy 128.730109 96.85) (xy 128.769891 96.85) + (xy 128.806645 96.834776) (xy 128.834776 96.806645) (xy 128.85 96.769891) (xy 128.85 96.749999) + (xy 128.962132 96.749999) (xy 128.962132 96.750001) (xy 129.30359 97.091459) (xy 129.303591 97.091458) + (xy 129.326016 97.057898) (xy 129.32602 97.057891) (xy 129.375021 96.939594) (xy 129.375022 96.93959) + (xy 129.399999 96.814023) (xy 129.4 96.81402) (xy 129.4 96.68598) (xy 129.399999 96.685976) (xy 129.375022 96.560409) + (xy 129.37502 96.560401) (xy 129.326023 96.442112) (xy 129.303591 96.40854) (xy 128.962132 96.749999) + (xy 128.85 96.749999) (xy 128.85 96.730109) (xy 128.834776 96.693355) (xy 128.806645 96.665224) + (xy 128.769891 96.65) (xy 128.730109 96.65) (xy 128.693355 96.665224) (xy 128.665224 96.693355) + (xy 128.65 96.730109) (xy 128.517978 96.730109) (xy 128.196408 96.408539) (xy 128.196407 96.40854) + (xy 128.173978 96.442109) (xy 128.124979 96.560401) (xy 128.124977 96.560409) (xy 128.1 96.685976) + (xy 126.311172 96.685976) (xy 126.228845 96.6696) (xy 126.228842 96.6696) (xy 126.071158 96.6696) + (xy 126.071155 96.6696) (xy 125.91651 96.700361) (xy 125.916498 96.700364) (xy 125.770827 96.760702) + (xy 125.770814 96.760709) (xy 125.639711 96.84831) (xy 125.639707 96.848313) (xy 125.528213 96.959807) + (xy 125.52821 96.959811) (xy 125.440609 97.090914) (xy 125.440602 97.090927) (xy 125.380264 97.236598) + (xy 125.380261 97.23661) (xy 125.3495 97.391253) (xy 124.280149 97.391253) (xy 124.279185 97.390609) + (xy 124.279172 97.390602) (xy 124.133501 97.330264) (xy 124.133489 97.330261) (xy 123.978845 97.2995) + (xy 123.978842 97.2995) (xy 123.821158 97.2995) (xy 123.821155 97.2995) (xy 123.66651 97.330261) + (xy 123.666498 97.330264) (xy 123.520827 97.390602) (xy 123.520814 97.390609) (xy 123.389711 97.47821) + (xy 123.389707 97.478213) (xy 123.278213 97.589707) (xy 123.27821 97.589711) (xy 123.190609 97.720814) + (xy 123.190602 97.720827) (xy 123.130264 97.866498) (xy 123.130261 97.86651) (xy 123.0995 98.021153) + (xy 120.2505 98.021153) (xy 120.2505 96.25) (xy 128.462132 96.25) (xy 128.75 96.537868) (xy 129.037868 96.25) + (xy 128.75 95.962132) (xy 128.462132 96.25) (xy 120.2505 96.25) (xy 120.2505 95.171153) (xy 122.9495 95.171153) + (xy 122.9495 95.328846) (xy 122.980261 95.483489) (xy 122.980264 95.483501) (xy 123.040602 95.629172) + (xy 123.040609 95.629185) (xy 123.12821 95.760288) (xy 123.128213 95.760292) (xy 123.239707 95.871786) + (xy 123.239711 95.871789) (xy 123.370814 95.95939) (xy 123.370827 95.959397) (xy 123.516498 96.019735) + (xy 123.516503 96.019737) (xy 123.671153 96.050499) (xy 123.671156 96.0505) (xy 123.671158 96.0505) + (xy 123.828844 96.0505) (xy 123.828845 96.050499) (xy 123.983497 96.019737) (xy 124.129179 95.959394) + (xy 124.260289 95.871789) (xy 124.371789 95.760289) (xy 124.421443 95.685976) (xy 128.1 95.685976) + (xy 128.1 95.814023) (xy 128.124977 95.93959) (xy 128.124979 95.939598) (xy 128.173976 96.057886) + (xy 128.173981 96.057896) (xy 128.196407 96.091458) (xy 128.196408 96.091458) (xy 128.537868 95.75) + (xy 128.537868 95.749999) (xy 128.517978 95.730109) (xy 128.65 95.730109) (xy 128.65 95.769891) + (xy 128.665224 95.806645) (xy 128.693355 95.834776) (xy 128.730109 95.85) (xy 128.769891 95.85) + (xy 128.806645 95.834776) (xy 128.834776 95.806645) (xy 128.85 95.769891) (xy 128.85 95.749999) + (xy 128.962132 95.749999) (xy 128.962132 95.750001) (xy 129.30359 96.091459) (xy 129.303591 96.091458) + (xy 129.326016 96.057898) (xy 129.32602 96.057891) (xy 129.375021 95.939594) (xy 129.375022 95.93959) + (xy 129.399999 95.814023) (xy 129.4 95.81402) (xy 129.4 95.68598) (xy 129.399999 95.685976) (xy 129.375022 95.560409) + (xy 129.37502 95.560401) (xy 129.326023 95.442112) (xy 129.303591 95.40854) (xy 128.962132 95.749999) + (xy 128.85 95.749999) (xy 128.85 95.730109) (xy 128.834776 95.693355) (xy 128.806645 95.665224) + (xy 128.769891 95.65) (xy 128.730109 95.65) (xy 128.693355 95.665224) (xy 128.665224 95.693355) + (xy 128.65 95.730109) (xy 128.517978 95.730109) (xy 128.196408 95.408539) (xy 128.196407 95.40854) + (xy 128.173978 95.442109) (xy 128.124979 95.560401) (xy 128.124977 95.560409) (xy 128.1 95.685976) + (xy 124.421443 95.685976) (xy 124.459394 95.629179) (xy 124.519737 95.483497) (xy 124.5505 95.328842) + (xy 124.5505 95.196408) (xy 128.408539 95.196408) (xy 128.75 95.537868) (xy 128.750001 95.537868) + (xy 129.091458 95.196408) (xy 129.091458 95.196407) (xy 129.057896 95.173981) (xy 129.057886 95.173976) + (xy 128.939598 95.124979) (xy 128.93959 95.124977) (xy 128.814023 95.1) (xy 128.685976 95.1) (xy 128.560409 95.124977) + (xy 128.560401 95.124979) (xy 128.442109 95.173978) (xy 128.40854 95.196407) (xy 128.408539 95.196408) + (xy 124.5505 95.196408) (xy 124.5505 95.171158) (xy 124.5505 95.171155) (xy 124.550499 95.171153) + (xy 124.519738 95.01651) (xy 124.519737 95.016503) (xy 124.483427 94.928842) (xy 124.459397 94.870827) + (xy 124.45939 94.870814) (xy 124.434763 94.833957) (xy 124.392798 94.771153) (xy 138.6995 94.771153) + (xy 138.6995 94.928846) (xy 138.730261 95.083489) (xy 138.730264 95.083501) (xy 138.790602 95.229172) + (xy 138.790609 95.229185) (xy 138.87821 95.360288) (xy 138.878213 95.360292) (xy 138.989707 95.471786) + (xy 138.989711 95.471789) (xy 139.120814 95.55939) (xy 139.120827 95.559397) (xy 139.266498 95.619735) + (xy 139.266503 95.619737) (xy 139.418644 95.65) (xy 139.421153 95.650499) (xy 139.421156 95.6505) + (xy 139.421158 95.6505) (xy 139.578844 95.6505) (xy 139.578845 95.650499) (xy 139.733497 95.619737) + (xy 139.879179 95.559394) (xy 140.010289 95.471789) (xy 140.121789 95.360289) (xy 140.209394 95.229179) + (xy 140.269737 95.083497) (xy 140.3005 94.928842) (xy 140.3005 94.771158) (xy 140.3005 94.771155) + (xy 140.300499 94.771153) (xy 140.272066 94.628211) (xy 140.269737 94.616503) (xy 140.238298 94.540602) + (xy 140.209397 94.470827) (xy 140.20939 94.470814) (xy 140.121789 94.339711) (xy 140.121786 94.339707) + (xy 140.010292 94.228213) (xy 140.010288 94.22821) (xy 139.879185 94.140609) (xy 139.879172 94.140602) + (xy 139.733501 94.080264) (xy 139.733489 94.080261) (xy 139.578845 94.0495) (xy 139.578842 94.0495) + (xy 139.421158 94.0495) (xy 139.421155 94.0495) (xy 139.26651 94.080261) (xy 139.266498 94.080264) + (xy 139.120827 94.140602) (xy 139.120814 94.140609) (xy 138.989711 94.22821) (xy 138.989707 94.228213) + (xy 138.878213 94.339707) (xy 138.87821 94.339711) (xy 138.790609 94.470814) (xy 138.790602 94.470827) + (xy 138.730264 94.616498) (xy 138.730261 94.61651) (xy 138.6995 94.771153) (xy 124.392798 94.771153) + (xy 124.371789 94.739711) (xy 124.371786 94.739707) (xy 124.260292 94.628213) (xy 124.260288 94.62821) + (xy 124.129185 94.540609) (xy 124.129172 94.540602) (xy 123.983501 94.480264) (xy 123.983489 94.480261) + (xy 123.828845 94.4495) (xy 123.828842 94.4495) (xy 123.671158 94.4495) (xy 123.671155 94.4495) + (xy 123.51651 94.480261) (xy 123.516498 94.480264) (xy 123.370827 94.540602) (xy 123.370814 94.540609) + (xy 123.239711 94.62821) (xy 123.239707 94.628213) (xy 123.128213 94.739707) (xy 123.12821 94.739711) + (xy 123.040609 94.870814) (xy 123.040602 94.870827) (xy 122.980264 95.016498) (xy 122.980261 95.01651) + (xy 122.9495 95.171153) (xy 120.2505 95.171153) (xy 120.2505 92.936152) (xy 126.96075 92.936152) + (xy 126.96075 93.093845) (xy 126.991511 93.248488) (xy 126.991514 93.2485) (xy 127.051852 93.394171) + (xy 127.051859 93.394184) (xy 127.13946 93.525287) (xy 127.139463 93.525291) (xy 127.250957 93.636785) + (xy 127.250961 93.636788) (xy 127.382064 93.724389) (xy 127.382077 93.724396) (xy 127.527748 93.784734) + (xy 127.527753 93.784736) (xy 127.682403 93.815498) (xy 127.682406 93.815499) (xy 127.682408 93.815499) + (xy 127.840094 93.815499) (xy 127.840095 93.815498) (xy 127.994747 93.784736) (xy 128.12886 93.729185) + (xy 128.140422 93.724396) (xy 128.140422 93.724395) (xy 128.140429 93.724393) (xy 128.271539 93.636788) + (xy 128.383039 93.525288) (xy 128.470644 93.394178) (xy 128.521602 93.271153) (xy 128.8995 93.271153) + (xy 128.8995 93.428846) (xy 128.930261 93.583489) (xy 128.930264 93.583501) (xy 128.990602 93.729172) + (xy 128.990609 93.729185) (xy 129.07821 93.860288) (xy 129.078213 93.860292) (xy 129.189707 93.971786) + (xy 129.189711 93.971789) (xy 129.320814 94.05939) (xy 129.320827 94.059397) (xy 129.466498 94.119735) + (xy 129.466503 94.119737) (xy 129.621153 94.150499) (xy 129.621156 94.1505) (xy 129.621158 94.1505) + (xy 129.778844 94.1505) (xy 129.778845 94.150499) (xy 129.933497 94.119737) (xy 130.079179 94.059394) + (xy 130.210289 93.971789) (xy 130.321789 93.860289) (xy 130.409394 93.729179) (xy 130.469737 93.583497) + (xy 130.5005 93.428842) (xy 130.5005 93.341804) (xy 130.520185 93.274765) (xy 130.555606 93.238704) + (xy 130.580923 93.221789) (xy 130.631559 93.171153) (xy 137.6995 93.171153) (xy 137.6995 93.328846) + (xy 137.730261 93.483489) (xy 137.730264 93.483501) (xy 137.790602 93.629172) (xy 137.790609 93.629185) + (xy 137.87821 93.760288) (xy 137.878213 93.760292) (xy 137.989707 93.871786) (xy 137.989711 93.871789) + (xy 138.120814 93.95939) (xy 138.120827 93.959397) (xy 138.266498 94.019735) (xy 138.266503 94.019737) + (xy 138.416131 94.0495) (xy 138.421153 94.050499) (xy 138.421156 94.0505) (xy 138.421158 94.0505) + (xy 138.578844 94.0505) (xy 138.578845 94.050499) (xy 138.733497 94.019737) (xy 138.879179 93.959394) + (xy 139.010289 93.871789) (xy 139.121789 93.760289) (xy 139.209394 93.629179) (xy 139.269737 93.483497) + (xy 139.3005 93.328842) (xy 139.3005 93.171158) (xy 139.3005 93.171155) (xy 139.300499 93.171153) + (xy 139.285121 93.093843) (xy 139.269737 93.016503) (xy 139.269735 93.016498) (xy 139.209397 92.870827) + (xy 139.20939 92.870814) (xy 139.121789 92.739711) (xy 139.121786 92.739707) (xy 139.010292 92.628213) + (xy 139.010288 92.62821) (xy 138.879185 92.540609) (xy 138.879172 92.540602) (xy 138.733501 92.480264) + (xy 138.733489 92.480261) (xy 138.578845 92.4495) (xy 138.578842 92.4495) (xy 138.421158 92.4495) + (xy 138.421155 92.4495) (xy 138.26651 92.480261) (xy 138.266498 92.480264) (xy 138.120827 92.540602) + (xy 138.120814 92.540609) (xy 137.989711 92.62821) (xy 137.989707 92.628213) (xy 137.878213 92.739707) + (xy 137.87821 92.739711) (xy 137.790609 92.870814) (xy 137.790602 92.870827) (xy 137.730264 93.016498) + (xy 137.730261 93.01651) (xy 137.6995 93.171153) (xy 130.631559 93.171153) (xy 130.692423 93.110289) + (xy 130.703414 93.093841) (xy 130.780024 92.979185) (xy 130.780024 92.979184) (xy 130.780028 92.979179) + (xy 130.783488 92.970827) (xy 130.79785 92.936152) (xy 130.840371 92.833497) (xy 130.871134 92.678842) + (xy 130.871134 92.521158) (xy 130.871134 92.521155) (xy 130.871133 92.521153) (xy 130.85688 92.4495) + (xy 130.840371 92.366503) (xy 130.815148 92.305608) (xy 130.780031 92.220827) (xy 130.780024 92.220814) + (xy 130.692423 92.089711) (xy 130.69242 92.089707) (xy 130.580926 91.978213) (xy 130.580922 91.97821) + (xy 130.449819 91.890609) (xy 130.449806 91.890602) (xy 130.304135 91.830264) (xy 130.304123 91.830261) + (xy 130.149479 91.7995) (xy 130.149476 91.7995) (xy 129.991792 91.7995) (xy 129.991789 91.7995) + (xy 129.837144 91.830261) (xy 129.837132 91.830264) (xy 129.691461 91.890602) (xy 129.691448 91.890609) + (xy 129.560345 91.97821) (xy 129.560341 91.978213) (xy 129.448847 92.089707) (xy 129.448844 92.089711) + (xy 129.361243 92.220814) (xy 129.361236 92.220827) (xy 129.300898 92.366498) (xy 129.300895 92.36651) + (xy 129.270134 92.521153) (xy 129.270134 92.608194) (xy 129.250449 92.675233) (xy 129.215026 92.711296) + (xy 129.189707 92.728213) (xy 129.078213 92.839707) (xy 129.07821 92.839711) (xy 128.990609 92.970814) + (xy 128.990602 92.970827) (xy 128.930264 93.116498) (xy 128.930261 93.11651) (xy 128.8995 93.271153) + (xy 128.521602 93.271153) (xy 128.530987 93.248496) (xy 128.557241 93.11651) (xy 128.56175 93.093843) + (xy 128.56175 92.936154) (xy 128.561749 92.936152) (xy 128.548752 92.870814) (xy 128.530987 92.781502) + (xy 128.508914 92.728213) (xy 128.470647 92.635826) (xy 128.47064 92.635813) (xy 128.383039 92.50471) + (xy 128.383036 92.504706) (xy 128.271542 92.393212) (xy 128.271538 92.393209) (xy 128.140435 92.305608) + (xy 128.140422 92.305601) (xy 127.994751 92.245263) (xy 127.994739 92.24526) (xy 127.840095 92.214499) + (xy 127.840092 92.214499) (xy 127.682408 92.214499) (xy 127.682405 92.214499) (xy 127.52776 92.24526) + (xy 127.527748 92.245263) (xy 127.382077 92.305601) (xy 127.382064 92.305608) (xy 127.250961 92.393209) + (xy 127.250957 92.393212) (xy 127.139463 92.504706) (xy 127.13946 92.50471) (xy 127.051859 92.635813) + (xy 127.051852 92.635826) (xy 126.991514 92.781497) (xy 126.991511 92.781509) (xy 126.96075 92.936152) + (xy 120.2505 92.936152) (xy 120.2505 90.621153) (xy 140.1495 90.621153) (xy 140.1495 90.778846) + (xy 140.180261 90.933489) (xy 140.180264 90.933501) (xy 140.240602 91.079172) (xy 140.240609 91.079185) + (xy 140.32821 91.210288) (xy 140.328213 91.210292) (xy 140.439707 91.321786) (xy 140.439711 91.321789) + (xy 140.570814 91.40939) (xy 140.570827 91.409397) (xy 140.67006 91.4505) (xy 140.716503 91.469737) + (xy 140.871153 91.500499) (xy 140.871156 91.5005) (xy 140.871158 91.5005) (xy 141.028844 91.5005) + (xy 141.028845 91.500499) (xy 141.183497 91.469737) (xy 141.329179 91.409394) (xy 141.460289 91.321789) + (xy 141.571789 91.210289) (xy 141.659394 91.079179) (xy 141.719737 90.933497) (xy 141.7505 90.778842) + (xy 141.7505 90.621158) (xy 141.7505 90.621155) (xy 141.744155 90.589258) (xy 141.744155 90.589257) + (xy 141.740554 90.571153) (xy 143.9995 90.571153) (xy 143.9995 90.728846) (xy 144.030261 90.883489) + (xy 144.030264 90.883501) (xy 144.090602 91.029172) (xy 144.090609 91.029185) (xy 144.17821 91.160288) + (xy 144.178213 91.160292) (xy 144.289707 91.271786) (xy 144.289711 91.271789) (xy 144.420814 91.35939) + (xy 144.420827 91.359397) (xy 144.566498 91.419735) (xy 144.566503 91.419737) (xy 144.721153 91.450499) + (xy 144.721156 91.4505) (xy 144.721158 91.4505) (xy 144.878844 91.4505) (xy 144.878845 91.450499) + (xy 145.033497 91.419737) (xy 145.179179 91.359394) (xy 145.310289 91.271789) (xy 145.421789 91.160289) + (xy 145.509394 91.029179) (xy 145.569737 90.883497) (xy 145.6005 90.728842) (xy 145.6005 90.571158) + (xy 145.6005 90.571155) (xy 145.600499 90.571153) (xy 145.579684 90.46651) (xy 145.569737 90.416503) + (xy 145.530102 90.320814) (xy 145.509397 90.270827) (xy 145.50939 90.270814) (xy 145.421789 90.139711) + (xy 145.421786 90.139707) (xy 145.310292 90.028213) (xy 145.310288 90.02821) (xy 145.179185 89.940609) + (xy 145.179172 89.940602) (xy 145.033501 89.880264) (xy 145.033489 89.880261) (xy 144.878845 89.8495) + (xy 144.878842 89.8495) (xy 144.721158 89.8495) (xy 144.721155 89.8495) (xy 144.56651 89.880261) + (xy 144.566498 89.880264) (xy 144.420827 89.940602) (xy 144.420814 89.940609) (xy 144.289711 90.02821) + (xy 144.289707 90.028213) (xy 144.178213 90.139707) (xy 144.17821 90.139711) (xy 144.090609 90.270814) + (xy 144.090602 90.270827) (xy 144.030264 90.416498) (xy 144.030261 90.41651) (xy 143.9995 90.571153) + (xy 141.740554 90.571153) (xy 141.719738 90.46651) (xy 141.719737 90.466503) (xy 141.719735 90.466498) + (xy 141.659397 90.320827) (xy 141.65939 90.320814) (xy 141.571789 90.189711) (xy 141.571786 90.189707) + (xy 141.460292 90.078213) (xy 141.460288 90.07821) (xy 141.329185 89.990609) (xy 141.329172 89.990602) + (xy 141.183501 89.930264) (xy 141.183489 89.930261) (xy 141.028845 89.8995) (xy 141.028842 89.8995) + (xy 140.871158 89.8995) (xy 140.871155 89.8995) (xy 140.71651 89.930261) (xy 140.716498 89.930264) + (xy 140.570827 89.990602) (xy 140.570814 89.990609) (xy 140.439711 90.07821) (xy 140.439707 90.078213) + (xy 140.328213 90.189707) (xy 140.32821 90.189711) (xy 140.240609 90.320814) (xy 140.240602 90.320827) + (xy 140.180264 90.466498) (xy 140.180261 90.46651) (xy 140.1495 90.621153) (xy 120.2505 90.621153) + (xy 120.2505 88.62211) (xy 130.125 88.62211) (xy 130.125 88.877889) (xy 130.165013 89.130523) (xy 130.244051 89.373781) + (xy 130.244052 89.373784) (xy 130.360175 89.601686) (xy 130.43785 89.708595) (xy 130.43785 89.708596) + (xy 131.168092 88.978354) (xy 131.196132 89.046048) (xy 131.264531 89.148414) (xy 131.351586 89.235469) + (xy 131.453952 89.303868) (xy 131.521645 89.331907) (xy 130.791402 90.062148) (xy 130.898313 90.139824) + (xy 131.126215 90.255947) (xy 131.126218 90.255948) (xy 131.369476 90.334986) (xy 131.622111 90.375) + (xy 131.877889 90.375) (xy 132.130523 90.334986) (xy 132.373781 90.255948) (xy 132.373784 90.255947) + (xy 132.601685 90.139825) (xy 132.708595 90.062148) (xy 132.708596 90.062148) (xy 131.978354 89.331907) + (xy 132.046048 89.303868) (xy 132.148414 89.235469) (xy 132.235469 89.148414) (xy 132.303868 89.046048) + (xy 132.331907 88.978354) (xy 133.062148 89.708596) (xy 133.062148 89.708595) (xy 133.139825 89.601685) + (xy 133.255947 89.373784) (xy 133.255948 89.373781) (xy 133.334986 89.130523) (xy 133.375 88.877889) + (xy 133.375 88.62211) (xy 133.374994 88.62207) (xy 136.6245 88.62207) (xy 136.6245 88.87793) (xy 136.644513 89.004284) + (xy 136.664526 89.13064) (xy 136.743588 89.373972) (xy 136.743589 89.373975) (xy 136.85975 89.60195) + (xy 137.010132 89.808935) (xy 137.010136 89.80894) (xy 137.191059 89.989863) (xy 137.191064 89.989867) + (xy 137.312663 90.078213) (xy 137.398053 90.140252) (xy 137.54708 90.216185) (xy 137.626024 90.25641) + (xy 137.626027 90.256411) (xy 137.670396 90.270827) (xy 137.869361 90.335474) (xy 138.12207 90.3755) + (xy 138.122071 90.3755) (xy 138.377929 90.3755) (xy 138.37793 90.3755) (xy 138.630639 90.335474) + (xy 138.873975 90.25641) (xy 139.101947 90.140252) (xy 139.308942 89.989862) (xy 139.489862 89.808942) + (xy 139.640252 89.601947) (xy 139.75641 89.373975) (xy 139.835474 89.130639) (xy 139.8755 88.87793) + (xy 139.8755 88.62207) (xy 139.835474 88.369361) (xy 139.773681 88.179179) (xy 139.756411 88.126027) + (xy 139.75641 88.126024) (xy 139.640384 87.898313) (xy 139.640252 87.898053) (xy 139.511729 87.721155) + (xy 139.489867 87.691064) (xy 139.489863 87.691059) (xy 139.30894 87.510136) (xy 139.308935 87.510132) + (xy 139.10195 87.35975) (xy 139.101949 87.359749) (xy 139.101947 87.359748) (xy 139.02891 87.322533) + (xy 138.873975 87.243589) (xy 138.873972 87.243588) (xy 138.63064 87.164526) (xy 138.504284 87.144513) + (xy 138.37793 87.1245) (xy 138.12207 87.1245) (xy 138.037833 87.137842) (xy 137.869359 87.164526) + (xy 137.626027 87.243588) (xy 137.626024 87.243589) (xy 137.398049 87.35975) (xy 137.191064 87.510132) + (xy 137.191059 87.510136) (xy 137.010136 87.691059) (xy 137.010132 87.691064) (xy 136.85975 87.898049) + (xy 136.743589 88.126024) (xy 136.743588 88.126027) (xy 136.664526 88.369359) (xy 136.656222 88.421789) + (xy 136.6245 88.62207) (xy 133.374994 88.62207) (xy 133.334986 88.369476) (xy 133.255948 88.126218) + (xy 133.255947 88.126215) (xy 133.139824 87.898313) (xy 133.062148 87.791403) (xy 133.062148 87.791402) + (xy 132.331906 88.521644) (xy 132.303868 88.453952) (xy 132.235469 88.351586) (xy 132.148414 88.264531) + (xy 132.046048 88.196132) (xy 131.978353 88.168092) (xy 132.708596 87.43785) (xy 132.601686 87.360175) + (xy 132.373784 87.244052) (xy 132.373781 87.244051) (xy 132.130523 87.165013) (xy 131.877889 87.125) + (xy 131.622111 87.125) (xy 131.369476 87.165013) (xy 131.126218 87.244051) (xy 131.126215 87.244052) + (xy 130.89831 87.360177) (xy 130.791403 87.437849) (xy 130.791402 87.43785) (xy 131.521645 88.168092) + (xy 131.453952 88.196132) (xy 131.351586 88.264531) (xy 131.264531 88.351586) (xy 131.196132 88.453952) + (xy 131.168092 88.521645) (xy 130.43785 87.791402) (xy 130.437849 87.791403) (xy 130.360177 87.89831) + (xy 130.244052 88.126215) (xy 130.244051 88.126218) (xy 130.165013 88.369476) (xy 130.125 88.62211) + (xy 120.2505 88.62211) (xy 120.2505 87.721153) (xy 121.4995 87.721153) (xy 121.4995 87.878846) (xy 121.530261 88.033489) + (xy 121.530264 88.033501) (xy 121.590602 88.179172) (xy 121.590609 88.179185) (xy 121.67821 88.310288) + (xy 121.678213 88.310292) (xy 121.789707 88.421786) (xy 121.789711 88.421789) (xy 121.920814 88.50939) + (xy 121.920827 88.509397) (xy 122.061571 88.567694) (xy 122.066503 88.569737) (xy 122.221153 88.600499) + (xy 122.221156 88.6005) (xy 122.221158 88.6005) (xy 122.378844 88.6005) (xy 122.378845 88.600499) + (xy 122.533497 88.569737) (xy 122.679179 88.509394) (xy 122.810289 88.421789) (xy 122.921789 88.310289) + (xy 123.009394 88.179179) (xy 123.069737 88.033497) (xy 123.1005 87.878842) (xy 123.1005 87.721158) + (xy 123.1005 87.721155) (xy 123.100499 87.721153) (xy 123.069738 87.56651) (xy 123.069737 87.566503) + (xy 123.016447 87.437849) (xy 123.009395 87.420823) (xy 123.00939 87.420814) (xy 122.921789 87.289711) + (xy 122.921786 87.289707) (xy 122.810292 87.178213) (xy 122.810288 87.17821) (xy 122.679185 87.090609) + (xy 122.679172 87.090602) (xy 122.533501 87.030264) (xy 122.533489 87.030261) (xy 122.378845 86.9995) + (xy 122.378842 86.9995) (xy 122.221158 86.9995) (xy 122.221155 86.9995) (xy 122.06651 87.030261) + (xy 122.066498 87.030264) (xy 121.920827 87.090602) (xy 121.920814 87.090609) (xy 121.789711 87.17821) + (xy 121.789707 87.178213) (xy 121.678213 87.289707) (xy 121.67821 87.289711) (xy 121.590609 87.420814) + (xy 121.590602 87.420827) (xy 121.530264 87.566498) (xy 121.530261 87.56651) (xy 121.4995 87.721153) + (xy 120.2505 87.721153) (xy 120.2505 85.693995) (xy 121.099499 85.693995) (xy 121.126418 85.829322) (xy 121.126421 85.829332) (xy 121.179221 85.956804) (xy 121.179228 85.956817) (xy 121.255885 86.071541) (xy 121.255888 86.071545) (xy 121.353454 86.169111) (xy 121.353458 86.169114) (xy 121.468182 86.245771) (xy 121.468195 86.245778) (xy 121.595667 86.298578) (xy 121.595672 86.29858) (xy 121.595676 86.29858) (xy 121.595677 86.298581) (xy 121.731004 86.3255) (xy 121.731007 86.3255) (xy 121.868995 86.3255) - (xy 121.960041 86.307389) (xy 122.004328 86.29858) (xy 122.131811 86.245775) (xy 122.246542 86.169114) - (xy 122.344114 86.071542) (xy 122.420775 85.956811) (xy 122.47358 85.829328) (xy 122.488084 85.756411) - (xy 122.5005 85.693995) (xy 122.5005 85.556004) (xy 122.473581 85.420677) (xy 122.47358 85.420676) - (xy 122.47358 85.420672) (xy 122.461175 85.390724) (xy 122.420778 85.293195) (xy 122.420771 85.293182) - (xy 122.344114 85.178458) (xy 122.344111 85.178454) (xy 122.246545 85.080888) (xy 122.246541 85.080885) - (xy 122.131817 85.004228) (xy 122.131804 85.004221) (xy 122.004332 84.951421) (xy 122.004322 84.951418) - (xy 121.868995 84.9245) (xy 121.868993 84.9245) (xy 121.731007 84.9245) (xy 121.731005 84.9245) - (xy 121.595677 84.951418) (xy 121.595667 84.951421) (xy 121.468195 85.004221) (xy 121.468182 85.004228) - (xy 121.353458 85.080885) (xy 121.353454 85.080888) (xy 121.255888 85.178454) (xy 121.255885 85.178458) - (xy 121.179228 85.293182) (xy 121.179221 85.293195) (xy 121.126421 85.420667) (xy 121.126418 85.420677) - (xy 121.0995 85.556004) (xy 121.0995 85.556007) (xy 121.0995 85.693993) (xy 121.0995 85.693995) - (xy 121.099499 85.693995) (xy 120.2505 85.693995) (xy 120.2505 83.355253) (xy 123.9541 83.355253) - (xy 123.9541 83.512946) (xy 123.984861 83.667589) (xy 123.984864 83.667601) (xy 124.045202 83.813272) - (xy 124.045209 83.813285) (xy 124.13281 83.944388) (xy 124.132813 83.944392) (xy 124.244307 84.055886) - (xy 124.244311 84.055889) (xy 124.375414 84.14349) (xy 124.375427 84.143497) (xy 124.521098 84.203835) - (xy 124.521103 84.203837) (xy 124.675753 84.234599) (xy 124.675756 84.2346) (xy 124.675758 84.2346) - (xy 124.833444 84.2346) (xy 124.833445 84.234599) (xy 124.988097 84.203837) (xy 125.124318 84.147413) - (xy 125.133772 84.143497) (xy 125.133772 84.143496) (xy 125.133779 84.143494) (xy 125.264889 84.055889) - (xy 125.376389 83.944389) (xy 125.463994 83.813279) (xy 125.524337 83.667597) (xy 125.5551 83.512942) - (xy 125.5551 83.383634) (xy 126.8995 83.383634) (xy 126.8995 83.616365) (xy 126.899501 83.616382) - (xy 126.925423 83.813285) (xy 126.929879 83.847126) (xy 126.986867 84.059809) (xy 126.99012 84.071947) - (xy 127.07918 84.28696) (xy 127.079188 84.286976) (xy 127.195553 84.488524) (xy 127.195564 84.48854) - (xy 127.337242 84.673179) (xy 127.337248 84.673186) (xy 127.501813 84.837751) (xy 127.50182 84.837757) - (xy 127.614866 84.9245) (xy 127.686468 84.979442) (xy 127.686475 84.979446) (xy 127.888023 85.095811) - (xy 127.888039 85.095819) (xy 128.103052 85.184879) (xy 128.103054 85.184879) (xy 128.10306 85.184882) - (xy 128.327874 85.245121) (xy 128.558628 85.2755) (xy 128.558635 85.2755) (xy 128.791365 85.2755) - (xy 128.791372 85.2755) (xy 129.022126 85.245121) (xy 129.24694 85.184882) (xy 129.304953 85.160852) - (xy 129.46196 85.095819) (xy 129.461963 85.095817) (xy 129.461969 85.095815) (xy 129.663532 84.979442) - (xy 129.848181 84.837756) (xy 129.994657 84.691279) (xy 130.055978 84.657796) (xy 130.12567 84.66278) - (xy 130.181604 84.704651) (xy 130.200268 84.740644) (xy 130.243588 84.873972) (xy 130.243589 84.873975) - (xy 130.297328 84.979442) (xy 130.349016 85.080885) (xy 130.35975 85.10195) (xy 130.510132 85.308935) - (xy 130.510136 85.30894) (xy 130.691059 85.489863) (xy 130.691064 85.489867) (xy 130.818167 85.582212) - (xy 130.898053 85.640252) (xy 131.04708 85.716185) (xy 131.126024 85.75641) (xy 131.126027 85.756411) - (xy 131.247693 85.795942) (xy 131.369361 85.835474) (xy 131.62207 85.8755) (xy 131.622071 85.8755) - (xy 131.877928 85.8755) (xy 131.87793 85.8755) (xy 132.004187 85.855502) (xy 132.073478 85.864456) - (xy 132.12693 85.909452) (xy 132.14757 85.976203) (xy 132.128846 86.043517) (xy 132.111265 86.065656) - (xy 131.99901 86.177911) (xy 131.911409 86.309014) (xy 131.911402 86.309027) (xy 131.851064 86.454698) - (xy 131.851061 86.45471) (xy 131.8203 86.609353) (xy 131.8203 86.767046) (xy 131.851061 86.921689) - (xy 131.851063 86.921697) (xy 131.864256 86.953547) (xy 131.871725 87.023016) (xy 131.84045 87.085496) - (xy 131.780361 87.121148) (xy 131.749695 87.125) (xy 131.622111 87.125) (xy 131.369476 87.165013) - (xy 131.126218 87.244051) (xy 131.126215 87.244052) (xy 130.89831 87.360177) (xy 130.791403 87.437849) - (xy 130.791402 87.43785) (xy 131.521645 88.168092) (xy 131.453952 88.196132) (xy 131.351586 88.264531) - (xy 131.264531 88.351586) (xy 131.196132 88.453952) (xy 131.168092 88.521645) (xy 130.43785 87.791402) - (xy 130.437849 87.791403) (xy 130.360177 87.89831) (xy 130.244052 88.126215) (xy 130.244051 88.126218) - (xy 130.165013 88.369476) (xy 130.125 88.62211) (xy 130.125 88.877889) (xy 130.165013 89.130523) - (xy 130.244051 89.373781) (xy 130.244052 89.373784) (xy 130.360175 89.601686) (xy 130.43785 89.708595) - (xy 130.43785 89.708596) (xy 131.168092 88.978354) (xy 131.196132 89.046048) (xy 131.264531 89.148414) - (xy 131.351586 89.235469) (xy 131.453952 89.303868) (xy 131.521645 89.331907) (xy 130.791402 90.062148) - (xy 130.898313 90.139824) (xy 131.126215 90.255947) (xy 131.126218 90.255948) (xy 131.369476 90.334986) - (xy 131.622111 90.375) (xy 131.877889 90.375) (xy 132.130523 90.334986) (xy 132.373781 90.255948) - (xy 132.373784 90.255947) (xy 132.601686 90.139824) (xy 132.70001 90.068388) (xy 132.765817 90.044908) - (xy 132.833871 90.060733) (xy 132.882566 90.110839) (xy 132.896441 90.179317) (xy 132.875998 90.237597) - (xy 132.842109 90.288314) (xy 132.842102 90.288327) (xy 132.781764 90.433998) (xy 132.781761 90.43401) - (xy 132.751 90.588653) (xy 132.751 90.746346) (xy 132.781761 90.900989) (xy 132.781764 90.901001) - (xy 132.842102 91.046672) (xy 132.842109 91.046685) (xy 132.92971 91.177788) (xy 132.929713 91.177792) - (xy 133.041207 91.289286) (xy 133.041211 91.289289) (xy 133.172314 91.37689) (xy 133.172327 91.376897) - (xy 133.317998 91.437235) (xy 133.318003 91.437237) (xy 133.472653 91.467999) (xy 133.472656 91.468) - (xy 133.472658 91.468) (xy 133.630344 91.468) (xy 133.630345 91.467999) (xy 133.784997 91.437237) - (xy 133.930679 91.376894) (xy 134.061789 91.289289) (xy 134.173289 91.177789) (xy 134.260894 91.046679) - (xy 134.321237 90.900997) (xy 134.352 90.746342) (xy 134.352 90.588658) (xy 134.352 90.588655) (xy 134.351999 90.588653) - (xy 134.338033 90.518442) (xy 134.321237 90.434003) (xy 134.298413 90.3789) (xy 134.260897 90.288327) - (xy 134.26089 90.288314) (xy 134.173289 90.157211) (xy 134.173286 90.157207) (xy 134.061792 90.045713) - (xy 134.061788 90.04571) (xy 133.930685 89.958109) (xy 133.930672 89.958102) (xy 133.785001 89.897764) - (xy 133.784989 89.897761) (xy 133.630345 89.867) (xy 133.630342 89.867) (xy 133.472658 89.867) (xy 133.472655 89.867) - (xy 133.31801 89.897761) (xy 133.317998 89.897764) (xy 133.17232 89.958105) (xy 133.171867 89.958348) - (xy 133.171602 89.958403) (xy 133.166692 89.960437) (xy 133.166306 89.959505) (xy 133.103463 89.972583) - (xy 133.038221 89.947577) (xy 132.996856 89.891268) (xy 132.9925 89.821534) (xy 133.013106 89.776098) - (xy 133.139824 89.601686) (xy 133.255947 89.373784) (xy 133.255948 89.373781) (xy 133.334986 89.130523) - (xy 133.375 88.877889) (xy 133.375 88.62211) (xy 133.374994 88.62207) (xy 136.6245 88.62207) (xy 136.6245 88.87793) - (xy 136.636962 88.95661) (xy 136.664526 89.13064) (xy 136.743588 89.373972) (xy 136.743589 89.373975) - (xy 136.85975 89.60195) (xy 137.010132 89.808935) (xy 137.010136 89.80894) (xy 137.191059 89.989863) - (xy 137.191064 89.989867) (xy 137.29914 90.068388) (xy 137.398053 90.140252) (xy 137.527306 90.20611) - (xy 137.626024 90.25641) (xy 137.626027 90.256411) (xy 137.722616 90.287794) (xy 137.869361 90.335474) - (xy 138.12207 90.3755) (xy 138.122071 90.3755) (xy 138.377929 90.3755) (xy 138.37793 90.3755) (xy 138.630639 90.335474) - (xy 138.873975 90.25641) (xy 139.101947 90.140252) (xy 139.308942 89.989862) (xy 139.489862 89.808942) - (xy 139.640252 89.601947) (xy 139.692425 89.499553) (xy 140.9025 89.499553) (xy 140.9025 89.657246) - (xy 140.933261 89.811889) (xy 140.933264 89.811901) (xy 140.993602 89.957572) (xy 140.993609 89.957585) - (xy 141.08121 90.088688) (xy 141.081213 90.088692) (xy 141.192707 90.200186) (xy 141.192711 90.200189) - (xy 141.323814 90.28779) (xy 141.323827 90.287797) (xy 141.469498 90.348135) (xy 141.469503 90.348137) - (xy 141.604552 90.375) (xy 141.624153 90.378899) (xy 141.624156 90.3789) (xy 141.624158 90.3789) - (xy 141.781844 90.3789) (xy 141.781845 90.378899) (xy 141.936497 90.348137) (xy 142.082179 90.287794) - (xy 142.213289 90.200189) (xy 142.324789 90.088689) (xy 142.412394 89.957579) (xy 142.472737 89.811897) - (xy 142.5035 89.657242) (xy 142.5035 89.499558) (xy 142.5035 89.499555) (xy 142.503499 89.499553) - (xy 142.49109 89.437171) (xy 142.472737 89.344903) (xy 142.45574 89.303868) (xy 142.412397 89.199227) - (xy 142.41239 89.199214) (xy 142.324789 89.068111) (xy 142.324786 89.068107) (xy 142.213292 88.956613) - (xy 142.213288 88.95661) (xy 142.082185 88.869009) (xy 142.082172 88.869002) (xy 141.936501 88.808664) - (xy 141.936489 88.808661) (xy 141.781845 88.7779) (xy 141.781842 88.7779) (xy 141.624158 88.7779) - (xy 141.624155 88.7779) (xy 141.46951 88.808661) (xy 141.469498 88.808664) (xy 141.323827 88.869002) - (xy 141.323814 88.869009) (xy 141.192711 88.95661) (xy 141.192707 88.956613) (xy 141.081213 89.068107) - (xy 141.08121 89.068111) (xy 140.993609 89.199214) (xy 140.993602 89.199227) (xy 140.933264 89.344898) - (xy 140.933261 89.34491) (xy 140.9025 89.499553) (xy 139.692425 89.499553) (xy 139.75641 89.373975) - (xy 139.835474 89.130639) (xy 139.8755 88.87793) (xy 139.8755 88.62207) (xy 139.835474 88.369361) - (xy 139.75641 88.126025) (xy 139.75641 88.126024) (xy 139.69958 88.01449) (xy 139.640252 87.898053) - (xy 139.580196 87.815392) (xy 139.489867 87.691064) (xy 139.489863 87.691059) (xy 139.30894 87.510136) - (xy 139.308935 87.510132) (xy 139.10195 87.35975) (xy 139.101949 87.359749) (xy 139.101947 87.359748) - (xy 139.00429 87.309989) (xy 138.873975 87.243589) (xy 138.873972 87.243588) (xy 138.63064 87.164526) - (xy 138.504284 87.144513) (xy 138.37793 87.1245) (xy 138.12207 87.1245) (xy 138.037833 87.137842) - (xy 137.869359 87.164526) (xy 137.626027 87.243588) (xy 137.626024 87.243589) (xy 137.398049 87.35975) - (xy 137.191064 87.510132) (xy 137.191059 87.510136) (xy 137.010136 87.691059) (xy 137.010132 87.691064) - (xy 136.85975 87.898049) (xy 136.743589 88.126024) (xy 136.743588 88.126027) (xy 136.664526 88.369359) - (xy 136.660236 88.396446) (xy 136.6245 88.62207) (xy 133.374994 88.62207) (xy 133.334986 88.369476) - (xy 133.255948 88.126218) (xy 133.255947 88.126215) (xy 133.139824 87.898313) (xy 133.062148 87.791403) - (xy 133.062148 87.791402) (xy 132.331907 88.521645) (xy 132.303868 88.453952) (xy 132.235469 88.351586) - (xy 132.148414 88.264531) (xy 132.046048 88.196132) (xy 131.978353 88.168092) (xy 132.621796 87.52465) - (xy 132.683119 87.491165) (xy 132.697331 87.488927) (xy 132.699633 87.4887) (xy 132.699642 87.4887) - (xy 132.699651 87.488698) (xy 132.699653 87.488698) (xy 132.736964 87.481275) (xy 132.854297 87.457937) - (xy 132.999979 87.397594) (xy 133.117135 87.319312) (xy 133.183809 87.298436) (xy 133.251189 87.31692) - (xy 133.29788 87.368899) (xy 133.30764 87.398224) (xy 133.335561 87.538591) (xy 133.335564 87.538601) - (xy 133.395902 87.684272) (xy 133.395909 87.684285) (xy 133.48351 87.815388) (xy 133.483513 87.815392) - (xy 133.595007 87.926886) (xy 133.595011 87.926889) (xy 133.726114 88.01449) (xy 133.726127 88.014497) - (xy 133.871798 88.074835) (xy 133.871803 88.074837) (xy 134.026453 88.105599) (xy 134.026456 88.1056) - (xy 134.026458 88.1056) (xy 134.184144 88.1056) (xy 134.184145 88.105599) (xy 134.338797 88.074837) - (xy 134.484479 88.014494) (xy 134.615589 87.926889) (xy 134.727089 87.815389) (xy 134.814694 87.684279) - (xy 134.875037 87.538597) (xy 134.9058 87.383942) (xy 134.9058 87.226258) (xy 134.9058 87.226255) - (xy 134.905799 87.226253) (xy 134.900276 87.198489) (xy 134.875037 87.071603) (xy 134.826137 86.953547) - (xy 134.814697 86.925927) (xy 134.81469 86.925914) (xy 134.727089 86.794811) (xy 134.727086 86.794807) - (xy 134.615592 86.683313) (xy 134.615588 86.68331) (xy 134.484485 86.595709) (xy 134.484472 86.595702) - (xy 134.338801 86.535364) (xy 134.338789 86.535361) (xy 134.184145 86.5046) (xy 134.184142 86.5046) - (xy 134.026458 86.5046) (xy 134.026455 86.5046) (xy 133.87181 86.535361) (xy 133.871798 86.535364) - (xy 133.726127 86.595702) (xy 133.726114 86.595709) (xy 133.608967 86.673985) (xy 133.542289 86.694863) - (xy 133.474909 86.676378) (xy 133.428219 86.624399) (xy 133.418459 86.595074) (xy 133.390538 86.45471) - (xy 133.390537 86.454703) (xy 133.337224 86.325992) (xy 133.330197 86.309027) (xy 133.33019 86.309014) - (xy 133.242589 86.177911) (xy 133.242586 86.177907) (xy 133.131092 86.066413) (xy 133.131088 86.06641) - (xy 132.999985 85.978809) (xy 132.999972 85.978802) (xy 132.854301 85.918464) (xy 132.854289 85.918461) - (xy 132.699645 85.8877) (xy 132.699642 85.8877) (xy 132.632801 85.8877) (xy 132.565762 85.868015) - (xy 132.520007 85.815211) (xy 132.510063 85.746053) (xy 132.539088 85.682497) (xy 132.576505 85.653216) - (xy 132.590522 85.646073) (xy 132.601947 85.640252) (xy 132.808942 85.489862) (xy 132.989862 85.308942) + (xy 121.960041 86.307389) (xy 122.004328 86.29858) (xy 122.131811 86.245775) (xy 122.16866 86.221153) + (xy 143.7995 86.221153) (xy 143.7995 86.378846) (xy 143.830261 86.533489) (xy 143.830264 86.533501) + (xy 143.890602 86.679172) (xy 143.890609 86.679185) (xy 143.97821 86.810288) (xy 143.978213 86.810292) + (xy 144.089707 86.921786) (xy 144.089711 86.921789) (xy 144.220814 87.00939) (xy 144.220827 87.009397) + (xy 144.366498 87.069735) (xy 144.366503 87.069737) (xy 144.521153 87.100499) (xy 144.521156 87.1005) + (xy 144.521158 87.1005) (xy 144.678844 87.1005) (xy 144.678845 87.100499) (xy 144.833497 87.069737) + (xy 144.979179 87.009394) (xy 145.110289 86.921789) (xy 145.221789 86.810289) (xy 145.309394 86.679179) + (xy 145.369737 86.533497) (xy 145.4005 86.378842) (xy 145.4005 86.221158) (xy 145.4005 86.221155) + (xy 145.400499 86.221153) (xy 145.369738 86.06651) (xy 145.369737 86.066503) (xy 145.324304 85.956817) + (xy 145.309397 85.920827) (xy 145.30939 85.920814) (xy 145.221789 85.789711) (xy 145.221786 85.789707) + (xy 145.126074 85.693995) (xy 147.499499 85.693995) (xy 147.526418 85.829322) (xy 147.526421 85.829332) + (xy 147.579221 85.956804) (xy 147.579228 85.956817) (xy 147.655885 86.071541) (xy 147.655888 86.071545) + (xy 147.753454 86.169111) (xy 147.753458 86.169114) (xy 147.868182 86.245771) (xy 147.868195 86.245778) + (xy 147.995667 86.298578) (xy 147.995672 86.29858) (xy 147.995676 86.29858) (xy 147.995677 86.298581) + (xy 148.131004 86.3255) (xy 148.131007 86.3255) (xy 148.268995 86.3255) (xy 148.360041 86.307389) + (xy 148.404328 86.29858) (xy 148.531811 86.245775) (xy 148.646542 86.169114) (xy 148.744114 86.071542) + (xy 148.820775 85.956811) (xy 148.87358 85.829328) (xy 148.888084 85.756411) (xy 148.9005 85.693995) + (xy 148.9005 85.556004) (xy 148.873581 85.420677) (xy 148.87358 85.420676) (xy 148.87358 85.420672) + (xy 148.873578 85.420667) (xy 148.820778 85.293195) (xy 148.820771 85.293182) (xy 148.744114 85.178458) + (xy 148.744111 85.178454) (xy 148.646545 85.080888) (xy 148.646541 85.080885) (xy 148.531817 85.004228) + (xy 148.531804 85.004221) (xy 148.404332 84.951421) (xy 148.404322 84.951418) (xy 148.268995 84.9245) + (xy 148.268993 84.9245) (xy 148.131007 84.9245) (xy 148.131005 84.9245) (xy 147.995677 84.951418) + (xy 147.995667 84.951421) (xy 147.868195 85.004221) (xy 147.868182 85.004228) (xy 147.753458 85.080885) + (xy 147.753454 85.080888) (xy 147.655888 85.178454) (xy 147.655885 85.178458) (xy 147.579228 85.293182) + (xy 147.579221 85.293195) (xy 147.526421 85.420667) (xy 147.526418 85.420677) (xy 147.4995 85.556004) + (xy 147.4995 85.556007) (xy 147.4995 85.693993) (xy 147.4995 85.693995) (xy 147.499499 85.693995) + (xy 145.126074 85.693995) (xy 145.110292 85.678213) (xy 145.110288 85.67821) (xy 145.072584 85.653017) + (xy 144.979185 85.590609) (xy 144.979172 85.590602) (xy 144.833501 85.530264) (xy 144.833489 85.530261) + (xy 144.678845 85.4995) (xy 144.678842 85.4995) (xy 144.521158 85.4995) (xy 144.521155 85.4995) + (xy 144.36651 85.530261) (xy 144.366498 85.530264) (xy 144.220827 85.590602) (xy 144.220814 85.590609) + (xy 144.089711 85.67821) (xy 144.089707 85.678213) (xy 143.978213 85.789707) (xy 143.97821 85.789711) + (xy 143.890609 85.920814) (xy 143.890602 85.920827) (xy 143.830264 86.066498) (xy 143.830261 86.06651) + (xy 143.7995 86.221153) (xy 122.16866 86.221153) (xy 122.246542 86.169114) (xy 122.246545 86.169111) + (xy 122.288272 86.127385) (xy 122.344111 86.071545) (xy 122.344114 86.071542) (xy 122.420775 85.956811) + (xy 122.47358 85.829328) (xy 122.488084 85.756411) (xy 122.5005 85.693995) (xy 122.5005 85.556004) + (xy 122.473581 85.420677) (xy 122.47358 85.420676) (xy 122.47358 85.420672) (xy 122.473578 85.420667) + (xy 122.420778 85.293195) (xy 122.420771 85.293182) (xy 122.344114 85.178458) (xy 122.344111 85.178454) + (xy 122.246545 85.080888) (xy 122.246541 85.080885) (xy 122.131817 85.004228) (xy 122.131804 85.004221) + (xy 122.004332 84.951421) (xy 122.004322 84.951418) (xy 121.868995 84.9245) (xy 121.868993 84.9245) + (xy 121.731007 84.9245) (xy 121.731005 84.9245) (xy 121.595677 84.951418) (xy 121.595667 84.951421) + (xy 121.468195 85.004221) (xy 121.468182 85.004228) (xy 121.353458 85.080885) (xy 121.353454 85.080888) + (xy 121.255888 85.178454) (xy 121.255885 85.178458) (xy 121.179228 85.293182) (xy 121.179221 85.293195) + (xy 121.126421 85.420667) (xy 121.126418 85.420677) (xy 121.0995 85.556004) (xy 121.0995 85.556007) + (xy 121.0995 85.693993) (xy 121.0995 85.693995) (xy 121.099499 85.693995) (xy 120.2505 85.693995) + (xy 120.2505 83.383634) (xy 126.8995 83.383634) (xy 126.8995 83.616365) (xy 126.899501 83.616382) + (xy 126.929878 83.847122) (xy 126.99012 84.071947) (xy 127.07918 84.28696) (xy 127.079188 84.286976) + (xy 127.195553 84.488524) (xy 127.195564 84.48854) (xy 127.337242 84.673179) (xy 127.337248 84.673186) + (xy 127.501813 84.837751) (xy 127.50182 84.837757) (xy 127.614866 84.9245) (xy 127.686468 84.979442) + (xy 127.686475 84.979446) (xy 127.888023 85.095811) (xy 127.888039 85.095819) (xy 128.103052 85.184879) + (xy 128.103054 85.184879) (xy 128.10306 85.184882) (xy 128.327874 85.245121) (xy 128.558628 85.2755) + (xy 128.558635 85.2755) (xy 128.791365 85.2755) (xy 128.791372 85.2755) (xy 129.022126 85.245121) + (xy 129.24694 85.184882) (xy 129.447165 85.101947) (xy 129.46196 85.095819) (xy 129.461963 85.095817) + (xy 129.461969 85.095815) (xy 129.663532 84.979442) (xy 129.848181 84.837756) (xy 129.994657 84.691279) + (xy 130.055978 84.657796) (xy 130.12567 84.66278) (xy 130.181604 84.704651) (xy 130.200268 84.740644) + (xy 130.243588 84.873972) (xy 130.243589 84.873975) (xy 130.297328 84.979442) (xy 130.349016 85.080885) + (xy 130.35975 85.10195) (xy 130.510132 85.308935) (xy 130.510136 85.30894) (xy 130.691059 85.489863) + (xy 130.691064 85.489867) (xy 130.782095 85.556004) (xy 130.898053 85.640252) (xy 131.04708 85.716185) + (xy 131.126024 85.75641) (xy 131.126027 85.756411) (xy 131.228503 85.789707) (xy 131.369361 85.835474) + (xy 131.62207 85.8755) (xy 131.622071 85.8755) (xy 131.877929 85.8755) (xy 131.87793 85.8755) (xy 132.130639 85.835474) + (xy 132.373975 85.75641) (xy 132.601947 85.640252) (xy 132.808942 85.489862) (xy 132.989862 85.308942) (xy 133.140252 85.101947) (xy 133.25641 84.873975) (xy 133.335474 84.630639) (xy 133.3755 84.37793) (xy 133.3755 84.12207) (xy 136.6245 84.12207) (xy 136.6245 84.377929) (xy 136.664526 84.63064) (xy 136.743588 84.873972) (xy 136.743589 84.873975) (xy 136.797328 84.979442) (xy 136.849016 85.080885) (xy 136.85975 85.10195) (xy 137.010132 85.308935) (xy 137.010136 85.30894) (xy 137.191059 85.489863) (xy 137.191064 85.489867) - (xy 137.318167 85.582212) (xy 137.398053 85.640252) (xy 137.54708 85.716185) (xy 137.626024 85.75641) - (xy 137.626027 85.756411) (xy 137.747693 85.795942) (xy 137.869361 85.835474) (xy 138.12207 85.8755) + (xy 137.282095 85.556004) (xy 137.398053 85.640252) (xy 137.54708 85.716185) (xy 137.626024 85.75641) + (xy 137.626027 85.756411) (xy 137.728503 85.789707) (xy 137.869361 85.835474) (xy 138.12207 85.8755) (xy 138.122071 85.8755) (xy 138.377929 85.8755) (xy 138.37793 85.8755) (xy 138.630639 85.835474) (xy 138.873975 85.75641) (xy 139.101947 85.640252) (xy 139.308942 85.489862) (xy 139.489862 85.308942) (xy 139.640252 85.101947) (xy 139.75641 84.873975) (xy 139.799731 84.740644) (xy 139.839168 84.682969) @@ -39242,111 +39780,64 @@ (xy 140.538023 85.095811) (xy 140.538039 85.095819) (xy 140.753052 85.184879) (xy 140.753054 85.184879) (xy 140.75306 85.184882) (xy 140.977874 85.245121) (xy 141.208628 85.2755) (xy 141.208635 85.2755) (xy 141.441365 85.2755) (xy 141.441372 85.2755) (xy 141.672126 85.245121) (xy 141.89694 85.184882) - (xy 141.954953 85.160852) (xy 142.11196 85.095819) (xy 142.111963 85.095817) (xy 142.111969 85.095815) - (xy 142.313532 84.979442) (xy 142.498181 84.837756) (xy 142.645584 84.690353) (xy 145.0042 84.690353) - (xy 145.0042 84.848046) (xy 145.034961 85.002689) (xy 145.034964 85.002701) (xy 145.095302 85.148372) - (xy 145.095309 85.148385) (xy 145.18291 85.279488) (xy 145.182913 85.279492) (xy 145.232822 85.329401) - (xy 145.266307 85.390724) (xy 145.261323 85.460416) (xy 145.259702 85.464534) (xy 145.210964 85.582198) - (xy 145.210961 85.58221) (xy 145.1802 85.736853) (xy 145.1802 85.894546) (xy 145.210961 86.049189) - (xy 145.210964 86.049201) (xy 145.271302 86.194872) (xy 145.271309 86.194885) (xy 145.35891 86.325988) - (xy 145.358913 86.325992) (xy 145.470407 86.437486) (xy 145.470411 86.437489) (xy 145.601514 86.52509) - (xy 145.601527 86.525097) (xy 145.747198 86.585435) (xy 145.747203 86.585437) (xy 145.901853 86.616199) - (xy 145.901856 86.6162) (xy 145.901858 86.6162) (xy 146.059544 86.6162) (xy 146.059545 86.616199) - (xy 146.214197 86.585437) (xy 146.359879 86.525094) (xy 146.490989 86.437489) (xy 146.602489 86.325989) - (xy 146.690094 86.194879) (xy 146.750437 86.049197) (xy 146.7812 85.894542) (xy 146.7812 85.736858) - (xy 146.7812 85.736855) (xy 146.781199 85.736853) (xy 146.772674 85.693995) (xy 147.499499 85.693995) - (xy 147.526418 85.829322) (xy 147.526421 85.829332) (xy 147.579221 85.956804) (xy 147.579228 85.956817) - (xy 147.655885 86.071541) (xy 147.655888 86.071545) (xy 147.753454 86.169111) (xy 147.753458 86.169114) - (xy 147.868182 86.245771) (xy 147.868195 86.245778) (xy 147.995667 86.298578) (xy 147.995672 86.29858) - (xy 147.995676 86.29858) (xy 147.995677 86.298581) (xy 148.131004 86.3255) (xy 148.131007 86.3255) - (xy 148.268995 86.3255) (xy 148.360041 86.307389) (xy 148.404328 86.29858) (xy 148.531811 86.245775) - (xy 148.646542 86.169114) (xy 148.744114 86.071542) (xy 148.820775 85.956811) (xy 148.87358 85.829328) - (xy 148.888084 85.756411) (xy 148.9005 85.693995) (xy 148.9005 85.556004) (xy 148.873581 85.420677) - (xy 148.87358 85.420676) (xy 148.87358 85.420672) (xy 148.861175 85.390724) (xy 148.820778 85.293195) - (xy 148.820771 85.293182) (xy 148.744114 85.178458) (xy 148.744111 85.178454) (xy 148.646545 85.080888) - (xy 148.646541 85.080885) (xy 148.531817 85.004228) (xy 148.531804 85.004221) (xy 148.404332 84.951421) - (xy 148.404322 84.951418) (xy 148.268995 84.9245) (xy 148.268993 84.9245) (xy 148.131007 84.9245) - (xy 148.131005 84.9245) (xy 147.995677 84.951418) (xy 147.995667 84.951421) (xy 147.868195 85.004221) - (xy 147.868182 85.004228) (xy 147.753458 85.080885) (xy 147.753454 85.080888) (xy 147.655888 85.178454) - (xy 147.655885 85.178458) (xy 147.579228 85.293182) (xy 147.579221 85.293195) (xy 147.526421 85.420667) - (xy 147.526418 85.420677) (xy 147.4995 85.556004) (xy 147.4995 85.556007) (xy 147.4995 85.693993) - (xy 147.4995 85.693995) (xy 147.499499 85.693995) (xy 146.772674 85.693995) (xy 146.750439 85.582212) - (xy 146.750438 85.58221) (xy 146.750437 85.582203) (xy 146.739585 85.556004) (xy 146.690097 85.436527) - (xy 146.69009 85.436514) (xy 146.602489 85.305411) (xy 146.602486 85.305407) (xy 146.552577 85.255498) - (xy 146.519092 85.194175) (xy 146.524076 85.124483) (xy 146.525675 85.120417) (xy 146.574437 85.002697) - (xy 146.6052 84.848042) (xy 146.6052 84.690358) (xy 146.6052 84.690355) (xy 146.605199 84.690353) - (xy 146.574438 84.53571) (xy 146.574437 84.535703) (xy 146.554895 84.488524) (xy 146.514097 84.390027) - (xy 146.51409 84.390014) (xy 146.426489 84.258911) (xy 146.426486 84.258907) (xy 146.314992 84.147413) - (xy 146.314988 84.14741) (xy 146.183885 84.059809) (xy 146.183872 84.059802) (xy 146.038201 83.999464) - (xy 146.038189 83.999461) (xy 145.883545 83.9687) (xy 145.883542 83.9687) (xy 145.725858 83.9687) - (xy 145.725855 83.9687) (xy 145.57121 83.999461) (xy 145.571198 83.999464) (xy 145.425527 84.059802) - (xy 145.425514 84.059809) (xy 145.294411 84.14741) (xy 145.294407 84.147413) (xy 145.182913 84.258907) - (xy 145.18291 84.258911) (xy 145.095309 84.390014) (xy 145.095302 84.390027) (xy 145.034964 84.535698) - (xy 145.034961 84.53571) (xy 145.0042 84.690353) (xy 142.645584 84.690353) (xy 142.662756 84.673181) - (xy 142.804442 84.488532) (xy 142.920815 84.286969) (xy 143.009882 84.07194) (xy 143.070121 83.847126) - (xy 143.1005 83.616372) (xy 143.1005 83.383628) (xy 143.070121 83.152874) (xy 143.009882 82.92806) - (xy 143.009879 82.928052) (xy 142.920819 82.713039) (xy 142.920811 82.713023) (xy 142.804446 82.511475) - (xy 142.804442 82.511468) (xy 142.804438 82.511463) (xy 142.804435 82.511458) (xy 142.795955 82.500407) - (xy 142.770761 82.435237) (xy 142.7848 82.366792) (xy 142.833614 82.316803) (xy 142.901706 82.30114) - (xy 142.950626 82.314436) (xy 143.144598 82.413271) (xy 143.372894 82.48745) (xy 143.609975 82.525) - (xy 143.850025 82.525) (xy 144.087105 82.48745) (xy 144.315401 82.413271) (xy 144.529274 82.304296) - (xy 144.617003 82.240556) (xy 144.617004 82.240556) (xy 143.879821 81.503375) (xy 143.932642 81.489222) - (xy 144.052357 81.420104) (xy 144.150104 81.322357) (xy 144.219222 81.202642) (xy 144.233375 81.149822) - (xy 144.970556 81.887004) (xy 144.970556 81.887003) (xy 145.034296 81.799274) (xy 145.143271 81.585401) - (xy 145.189217 81.443995) (xy 147.499499 81.443995) (xy 147.526418 81.579322) (xy 147.526421 81.579332) - (xy 147.579221 81.706804) (xy 147.579228 81.706817) (xy 147.655885 81.821541) (xy 147.655888 81.821545) - (xy 147.753454 81.919111) (xy 147.753458 81.919114) (xy 147.868182 81.995771) (xy 147.868195 81.995778) - (xy 147.995667 82.048578) (xy 147.995672 82.04858) (xy 147.995676 82.04858) (xy 147.995677 82.048581) - (xy 148.131004 82.0755) (xy 148.131007 82.0755) (xy 148.268995 82.0755) (xy 148.360041 82.057389) - (xy 148.404328 82.04858) (xy 148.531811 81.995775) (xy 148.646542 81.919114) (xy 148.744114 81.821542) - (xy 148.820775 81.706811) (xy 148.87358 81.579328) (xy 148.884387 81.525) (xy 148.9005 81.443995) - (xy 148.9005 81.306004) (xy 148.873581 81.170677) (xy 148.87358 81.170676) (xy 148.87358 81.170672) - (xy 148.860456 81.138988) (xy 148.820778 81.043195) (xy 148.820771 81.043182) (xy 148.744114 80.928458) - (xy 148.744111 80.928454) (xy 148.646545 80.830888) (xy 148.646541 80.830885) (xy 148.531817 80.754228) - (xy 148.531804 80.754221) (xy 148.404332 80.701421) (xy 148.404322 80.701418) (xy 148.268995 80.6745) - (xy 148.268993 80.6745) (xy 148.131007 80.6745) (xy 148.131005 80.6745) (xy 147.995677 80.701418) - (xy 147.995667 80.701421) (xy 147.868195 80.754221) (xy 147.868182 80.754228) (xy 147.753458 80.830885) - (xy 147.753454 80.830888) (xy 147.655888 80.928454) (xy 147.655885 80.928458) (xy 147.579228 81.043182) - (xy 147.579221 81.043195) (xy 147.526421 81.170667) (xy 147.526418 81.170677) (xy 147.4995 81.306004) - (xy 147.4995 81.306007) (xy 147.4995 81.443993) (xy 147.4995 81.443995) (xy 147.499499 81.443995) - (xy 145.189217 81.443995) (xy 145.217449 81.357106) (xy 145.229581 81.280516) (xy 145.229581 81.280515) - (xy 145.255 81.120025) (xy 145.255 80.879974) (xy 145.21745 80.642894) (xy 145.143271 80.414598) - (xy 145.034294 80.200722) (xy 144.970557 80.112995) (xy 144.970556 80.112994) (xy 144.233374 80.850176) - (xy 144.219222 80.797358) (xy 144.150104 80.677643) (xy 144.052357 80.579896) (xy 143.932642 80.510778) - (xy 143.87982 80.496624) (xy 144.649356 79.72709) (xy 144.671825 79.701345) (xy 144.723792 79.663589) - (xy 144.723792 79.663588) (xy 144.723796 79.663586) (xy 144.893586 79.493796) (xy 145.034724 79.299536) - (xy 145.143736 79.085589) (xy 145.217937 78.857222) (xy 145.2555 78.620059) (xy 145.2555 78.379941) - (xy 145.217937 78.142778) (xy 145.143736 77.914411) (xy 145.143734 77.914408) (xy 145.143734 77.914406) - (xy 145.034723 77.700463) (xy 144.893586 77.506204) (xy 144.725063 77.337681) (xy 144.691578 77.276358) - (xy 144.696562 77.206666) (xy 144.725063 77.162319) (xy 144.893586 76.993796) (xy 145.034724 76.799536) - (xy 145.143736 76.585589) (xy 145.217937 76.357222) (xy 145.2555 76.120059) (xy 145.2555 76.091353) - (xy 146.2143 76.091353) (xy 146.2143 76.249046) (xy 146.245061 76.403689) (xy 146.245064 76.403701) - (xy 146.305402 76.549372) (xy 146.305409 76.549385) (xy 146.39301 76.680488) (xy 146.393013 76.680492) - (xy 146.504507 76.791986) (xy 146.504511 76.791989) (xy 146.635614 76.87959) (xy 146.635627 76.879597) - (xy 146.781298 76.939935) (xy 146.781303 76.939937) (xy 146.935953 76.970699) (xy 146.935956 76.9707) - (xy 146.935958 76.9707) (xy 147.093644 76.9707) (xy 147.093645 76.970699) (xy 147.248297 76.939937) - (xy 147.393979 76.879594) (xy 147.525089 76.791989) (xy 147.636589 76.680489) (xy 147.724194 76.549379) - (xy 147.784537 76.403697) (xy 147.790449 76.373974) (xy 147.822832 76.312065) (xy 147.883548 76.27749) - (xy 147.953317 76.281229) (xy 147.959518 76.283605) (xy 147.995667 76.298578) (xy 147.995672 76.29858) - (xy 147.995676 76.29858) (xy 147.995677 76.298581) (xy 148.131004 76.3255) (xy 148.131007 76.3255) - (xy 148.268995 76.3255) (xy 148.360041 76.307389) (xy 148.404328 76.29858) (xy 148.531811 76.245775) - (xy 148.646542 76.169114) (xy 148.744114 76.071542) (xy 148.820775 75.956811) (xy 148.87358 75.829328) - (xy 148.9005 75.693993) (xy 148.9005 75.556007) (xy 148.9005 75.556004) (xy 148.873581 75.420677) - (xy 148.87358 75.420676) (xy 148.87358 75.420672) (xy 148.865209 75.400463) (xy 148.820778 75.293195) - (xy 148.820771 75.293182) (xy 148.744114 75.178458) (xy 148.744111 75.178454) (xy 148.646545 75.080888) - (xy 148.646541 75.080885) (xy 148.531817 75.004228) (xy 148.531804 75.004221) (xy 148.404332 74.951421) - (xy 148.404322 74.951418) (xy 148.268995 74.9245) (xy 148.268993 74.9245) (xy 148.131007 74.9245) - (xy 148.131005 74.9245) (xy 147.995677 74.951418) (xy 147.995667 74.951421) (xy 147.868195 75.004221) - (xy 147.868182 75.004228) (xy 147.753458 75.080885) (xy 147.753454 75.080888) (xy 147.655888 75.178454) - (xy 147.655885 75.178458) (xy 147.579228 75.293182) (xy 147.579223 75.293192) (xy 147.540287 75.387192) - (xy 147.496446 75.441595) (xy 147.430151 75.46366) (xy 147.378274 75.4543) (xy 147.248301 75.400464) - (xy 147.248289 75.400461) (xy 147.093645 75.3697) (xy 147.093642 75.3697) (xy 146.935958 75.3697) - (xy 146.935955 75.3697) (xy 146.78131 75.400461) (xy 146.781298 75.400464) (xy 146.635627 75.460802) - (xy 146.635614 75.460809) (xy 146.504511 75.54841) (xy 146.504507 75.548413) (xy 146.393013 75.659907) - (xy 146.39301 75.659911) (xy 146.305409 75.791014) (xy 146.305402 75.791027) (xy 146.245064 75.936698) - (xy 146.245061 75.93671) (xy 146.2143 76.091353) (xy 145.2555 76.091353) (xy 145.2555 75.879941) - (xy 145.217937 75.642778) (xy 145.143736 75.414411) (xy 145.143734 75.414408) (xy 145.143734 75.414406) - (xy 145.081973 75.293195) (xy 145.034724 75.200464) (xy 144.893586 75.006204) (xy 144.723796 74.836414) + (xy 142.097165 85.101947) (xy 142.11196 85.095819) (xy 142.111963 85.095817) (xy 142.111969 85.095815) + (xy 142.313532 84.979442) (xy 142.498181 84.837756) (xy 142.662756 84.673181) (xy 142.804442 84.488532) + (xy 142.920815 84.286969) (xy 143.009882 84.07194) (xy 143.070121 83.847126) (xy 143.1005 83.616372) + (xy 143.1005 83.383628) (xy 143.070121 83.152874) (xy 143.009882 82.92806) (xy 143.009879 82.928052) + (xy 142.920819 82.713039) (xy 142.920811 82.713023) (xy 142.804446 82.511475) (xy 142.804442 82.511468) + (xy 142.804438 82.511463) (xy 142.804435 82.511458) (xy 142.795955 82.500407) (xy 142.770761 82.435237) + (xy 142.7848 82.366792) (xy 142.833614 82.316803) (xy 142.901706 82.30114) (xy 142.950626 82.314436) + (xy 143.144598 82.413271) (xy 143.372894 82.48745) (xy 143.609975 82.525) (xy 143.850025 82.525) + (xy 144.087105 82.48745) (xy 144.315401 82.413271) (xy 144.529274 82.304296) (xy 144.617003 82.240556) + (xy 144.617004 82.240556) (xy 143.879822 81.503375) (xy 143.932642 81.489222) (xy 144.052357 81.420104) + (xy 144.150104 81.322357) (xy 144.219222 81.202642) (xy 144.233375 81.149822) (xy 144.970556 81.887004) + (xy 144.970556 81.887003) (xy 145.034296 81.799274) (xy 145.143271 81.585401) (xy 145.189217 81.443995) + (xy 147.499499 81.443995) (xy 147.526418 81.579322) (xy 147.526421 81.579332) (xy 147.579221 81.706804) + (xy 147.579228 81.706817) (xy 147.655885 81.821541) (xy 147.655888 81.821545) (xy 147.753454 81.919111) + (xy 147.753458 81.919114) (xy 147.868182 81.995771) (xy 147.868195 81.995778) (xy 147.995667 82.048578) + (xy 147.995672 82.04858) (xy 147.995676 82.04858) (xy 147.995677 82.048581) (xy 148.131004 82.0755) + (xy 148.131007 82.0755) (xy 148.268995 82.0755) (xy 148.360041 82.057389) (xy 148.404328 82.04858) + (xy 148.531811 81.995775) (xy 148.646542 81.919114) (xy 148.744114 81.821542) (xy 148.820775 81.706811) + (xy 148.87358 81.579328) (xy 148.884387 81.525) (xy 148.9005 81.443995) (xy 148.9005 81.306004) + (xy 148.873581 81.170677) (xy 148.87358 81.170676) (xy 148.87358 81.170672) (xy 148.858159 81.133442) + (xy 148.820778 81.043195) (xy 148.820771 81.043182) (xy 148.744114 80.928458) (xy 148.744111 80.928454) + (xy 148.646545 80.830888) (xy 148.646541 80.830885) (xy 148.531817 80.754228) (xy 148.531804 80.754221) + (xy 148.404332 80.701421) (xy 148.404322 80.701418) (xy 148.268995 80.6745) (xy 148.268993 80.6745) + (xy 148.131007 80.6745) (xy 148.131005 80.6745) (xy 147.995677 80.701418) (xy 147.995667 80.701421) + (xy 147.868195 80.754221) (xy 147.868182 80.754228) (xy 147.753458 80.830885) (xy 147.753454 80.830888) + (xy 147.655888 80.928454) (xy 147.655885 80.928458) (xy 147.579228 81.043182) (xy 147.579221 81.043195) + (xy 147.526421 81.170667) (xy 147.526418 81.170677) (xy 147.4995 81.306004) (xy 147.4995 81.306007) + (xy 147.4995 81.443993) (xy 147.4995 81.443995) (xy 147.499499 81.443995) (xy 145.189217 81.443995) + (xy 145.217449 81.357106) (xy 145.229581 81.280516) (xy 145.229581 81.280515) (xy 145.255 81.120025) + (xy 145.255 80.879974) (xy 145.21745 80.642894) (xy 145.143271 80.414598) (xy 145.034294 80.200722) + (xy 144.970557 80.112995) (xy 144.970556 80.112994) (xy 144.233374 80.850176) (xy 144.219222 80.797358) + (xy 144.150104 80.677643) (xy 144.052357 80.579896) (xy 143.932642 80.510778) (xy 143.879821 80.496624) + (xy 144.649356 79.72709) (xy 144.671825 79.701345) (xy 144.723792 79.663589) (xy 144.723792 79.663588) + (xy 144.723796 79.663586) (xy 144.893586 79.493796) (xy 145.034724 79.299536) (xy 145.143736 79.085589) + (xy 145.217937 78.857222) (xy 145.2555 78.620059) (xy 145.2555 78.379941) (xy 145.217937 78.142778) + (xy 145.143736 77.914411) (xy 145.143734 77.914408) (xy 145.143734 77.914406) (xy 145.034723 77.700463) + (xy 144.893586 77.506204) (xy 144.725063 77.337681) (xy 144.691578 77.276358) (xy 144.696562 77.206666) + (xy 144.725063 77.162319) (xy 144.893586 76.993796) (xy 145.034724 76.799536) (xy 145.143736 76.585589) + (xy 145.217937 76.357222) (xy 145.2555 76.120059) (xy 145.2555 75.879941) (xy 145.226049 75.693995) + (xy 147.499499 75.693995) (xy 147.526418 75.829322) (xy 147.526421 75.829332) (xy 147.579221 75.956804) + (xy 147.579228 75.956817) (xy 147.655885 76.071541) (xy 147.655888 76.071545) (xy 147.753454 76.169111) + (xy 147.753458 76.169114) (xy 147.868182 76.245771) (xy 147.868195 76.245778) (xy 147.995667 76.298578) + (xy 147.995672 76.29858) (xy 147.995676 76.29858) (xy 147.995677 76.298581) (xy 148.131004 76.3255) + (xy 148.131007 76.3255) (xy 148.268995 76.3255) (xy 148.360041 76.307389) (xy 148.404328 76.29858) + (xy 148.531811 76.245775) (xy 148.646542 76.169114) (xy 148.744114 76.071542) (xy 148.820775 75.956811) + (xy 148.87358 75.829328) (xy 148.9005 75.693993) (xy 148.9005 75.556007) (xy 148.9005 75.556004) + (xy 148.873581 75.420677) (xy 148.87358 75.420676) (xy 148.87358 75.420672) (xy 148.870985 75.414406) + (xy 148.820778 75.293195) (xy 148.820771 75.293182) (xy 148.744114 75.178458) (xy 148.744111 75.178454) + (xy 148.646545 75.080888) (xy 148.646541 75.080885) (xy 148.531817 75.004228) (xy 148.531804 75.004221) + (xy 148.404332 74.951421) (xy 148.404322 74.951418) (xy 148.268995 74.9245) (xy 148.268993 74.9245) + (xy 148.131007 74.9245) (xy 148.131005 74.9245) (xy 147.995677 74.951418) (xy 147.995667 74.951421) + (xy 147.868195 75.004221) (xy 147.868182 75.004228) (xy 147.753458 75.080885) (xy 147.753454 75.080888) + (xy 147.655888 75.178454) (xy 147.655885 75.178458) (xy 147.579228 75.293182) (xy 147.579221 75.293195) + (xy 147.526421 75.420667) (xy 147.526418 75.420677) (xy 147.4995 75.556004) (xy 147.4995 75.556007) + (xy 147.4995 75.693993) (xy 147.4995 75.693995) (xy 147.499499 75.693995) (xy 145.226049 75.693995) + (xy 145.217937 75.642778) (xy 145.217936 75.642774) (xy 145.217936 75.642773) (xy 145.200215 75.588233) + (xy 145.14577 75.420672) (xy 145.143736 75.414411) (xy 145.143734 75.414408) (xy 145.143734 75.414406) + (xy 145.034723 75.200463) (xy 145.020267 75.180566) (xy 144.893586 75.006204) (xy 144.723796 74.836414) (xy 144.529536 74.695276) (xy 144.508666 74.684642) (xy 144.315593 74.586265) (xy 144.087222 74.512063) (xy 143.850059 74.4745) (xy 143.609941 74.4745) (xy 143.521397 74.488524) (xy 143.372777 74.512063) (xy 143.273412 74.544349) (xy 143.144411 74.586264) (xy 143.144408 74.586265) (xy 143.144406 74.586266) @@ -39354,11 +39845,11 @@ (xy 142.774673 74.544349) (xy 142.796664 74.498667) (xy 142.804442 74.488532) (xy 142.920815 74.286969) (xy 143.009882 74.07194) (xy 143.070121 73.847126) (xy 143.1005 73.616372) (xy 143.1005 73.383628) (xy 143.070121 73.152874) (xy 143.009882 72.92806) (xy 143.009879 72.928052) (xy 142.920819 72.713039) - (xy 142.920811 72.713023) (xy 142.804446 72.511475) (xy 142.804442 72.511468) (xy 142.73363 72.419184) - (xy 142.662757 72.32682) (xy 142.662751 72.326813) (xy 142.498186 72.162248) (xy 142.498179 72.162242) - (xy 142.31354 72.020564) (xy 142.313533 72.020559) (xy 142.313532 72.020558) (xy 142.313527 72.020555) + (xy 142.920811 72.713023) (xy 142.804446 72.511475) (xy 142.804443 72.51147) (xy 142.804442 72.511468) + (xy 142.662756 72.326819) (xy 142.662751 72.326813) (xy 142.498186 72.162248) (xy 142.498179 72.162242) + (xy 142.31354 72.020564) (xy 142.313538 72.020562) (xy 142.313532 72.020558) (xy 142.313527 72.020555) (xy 142.313524 72.020553) (xy 142.111976 71.904188) (xy 142.11196 71.90418) (xy 141.896947 71.81512) - (xy 141.86481 71.806509) (xy 141.672126 71.754879) (xy 141.672125 71.754878) (xy 141.672122 71.754878) + (xy 141.729539 71.770263) (xy 141.672126 71.754879) (xy 141.672125 71.754878) (xy 141.672122 71.754878) (xy 141.441382 71.724501) (xy 141.441377 71.7245) (xy 141.441372 71.7245) (xy 141.208628 71.7245) (xy 141.208622 71.7245) (xy 141.208617 71.724501) (xy 140.977877 71.754878) (xy 140.753052 71.81512) (xy 140.538039 71.90418) (xy 140.538023 71.904188) (xy 140.336475 72.020553) (xy 140.336459 72.020564) @@ -39376,14 +39867,20 @@ (xy 142.411339 75.006674) (xy 142.45453 75.061595) (xy 142.461172 75.131148) (xy 142.439732 75.180566) (xy 142.425277 75.200461) (xy 142.316265 75.414406) (xy 142.242063 75.642777) (xy 142.242063 75.642778) (xy 142.2045 75.879941) (xy 142.2045 76.120059) (xy 142.224412 76.245778) (xy 142.242063 76.357222) - (xy 142.316265 76.585593) (xy 142.421429 76.791986) (xy 142.425276 76.799536) (xy 142.566414 76.993796) - (xy 142.566416 76.993798) (xy 142.734937 77.162319) (xy 142.768422 77.223642) (xy 142.763438 77.293334) - (xy 142.734937 77.337681) (xy 142.566416 77.506201) (xy 142.425276 77.700463) (xy 142.316265 77.914406) - (xy 142.242063 78.142777) (xy 142.2045 78.379941) (xy 142.2045 78.620058) (xy 142.242063 78.857222) - (xy 142.316265 79.085593) (xy 142.425276 79.299536) (xy 142.566414 79.493796) (xy 142.736204 79.663586) - (xy 142.788174 79.701344) (xy 142.802139 79.719454) (xy 142.802573 79.719021) (xy 143.580177 80.496624) - (xy 143.527358 80.510778) (xy 143.407643 80.579896) (xy 143.309896 80.677643) (xy 143.240778 80.797358) - (xy 143.226624 80.850178) (xy 142.489442 80.112995) (xy 142.425701 80.200729) (xy 142.316728 80.414598) + (xy 142.316265 76.585593) (xy 142.425276 76.799536) (xy 142.566414 76.993796) (xy 142.566416 76.993798) + (xy 142.734937 77.162319) (xy 142.768422 77.223642) (xy 142.763438 77.293334) (xy 142.734937 77.337681) + (xy 142.566416 77.506201) (xy 142.425276 77.700463) (xy 142.316265 77.914406) (xy 142.242063 78.142777) + (xy 142.204499 78.379943) (xy 142.204117 78.384804) (xy 142.201821 78.384623) (xy 142.184815 78.442539) + (xy 142.132011 78.488294) (xy 142.0805 78.4995) (xy 142.021155 78.4995) (xy 141.86651 78.530261) + (xy 141.866498 78.530264) (xy 141.720827 78.590602) (xy 141.720814 78.590609) (xy 141.589711 78.67821) + (xy 141.589707 78.678213) (xy 141.478213 78.789707) (xy 141.47821 78.789711) (xy 141.390609 78.920814) + (xy 141.390602 78.920827) (xy 141.330264 79.066498) (xy 141.330261 79.06651) (xy 141.2995 79.221153) + (xy 141.2995 79.378846) (xy 141.330261 79.533489) (xy 141.330264 79.533501) (xy 141.390602 79.679172) + (xy 141.390609 79.679185) (xy 141.47821 79.810288) (xy 141.478213 79.810292) (xy 141.589707 79.921786) + (xy 141.589711 79.921789) (xy 141.720814 80.00939) (xy 141.720827 80.009397) (xy 141.866498 80.069735) + (xy 141.866503 80.069737) (xy 142.021153 80.100499) (xy 142.021156 80.1005) (xy 142.021158 80.1005) + (xy 142.178843 80.1005) (xy 142.228326 80.090657) (xy 142.25963 80.08443) (xy 142.329221 80.090657) + (xy 142.384399 80.133519) (xy 142.407644 80.199409) (xy 142.394307 80.262341) (xy 142.316729 80.414595) (xy 142.242549 80.642894) (xy 142.205 80.879974) (xy 142.205 81.120025) (xy 142.242549 81.357105) (xy 142.316728 81.585401) (xy 142.425705 81.799277) (xy 142.440794 81.820046) (xy 142.464274 81.885852) (xy 142.448448 81.953906) (xy 142.398343 82.002601) (xy 142.329865 82.016476) (xy 142.278476 82.000318) @@ -39397,80 +39894,56 @@ (xy 139.640121 82.928052) (xy 139.640118 82.92806) (xy 139.622177 82.995015) (xy 139.608374 83.046528) (xy 139.572008 83.106188) (xy 139.509161 83.136716) (xy 139.439785 83.128421) (xy 139.400918 83.102114) (xy 139.30894 83.010136) (xy 139.308935 83.010132) (xy 139.10195 82.85975) (xy 139.101949 82.859749) - (xy 139.101947 82.859748) (xy 139.008845 82.81231) (xy 138.873975 82.743589) (xy 138.873972 82.743588) + (xy 139.101947 82.859748) (xy 139.02891 82.822533) (xy 138.873975 82.743589) (xy 138.873972 82.743588) (xy 138.63064 82.664526) (xy 138.504284 82.644513) (xy 138.37793 82.6245) (xy 138.12207 82.6245) - (xy 138.064616 82.6336) (xy 137.869359 82.664526) (xy 137.626027 82.743588) (xy 137.626024 82.743589) + (xy 138.037833 82.637842) (xy 137.869359 82.664526) (xy 137.626027 82.743588) (xy 137.626024 82.743589) (xy 137.398049 82.85975) (xy 137.191064 83.010132) (xy 137.191059 83.010136) (xy 137.010136 83.191059) (xy 137.010132 83.191064) (xy 136.85975 83.398049) (xy 136.743589 83.626024) (xy 136.743588 83.626027) (xy 136.664526 83.869359) (xy 136.6245 84.12207) (xy 133.3755 84.12207) (xy 133.335474 83.869361) - (xy 133.269919 83.667601) (xy 133.256411 83.626027) (xy 133.25641 83.626024) (xy 133.198791 83.512942) - (xy 133.140252 83.398053) (xy 133.061814 83.290092) (xy 132.989867 83.191064) (xy 132.989863 83.191059) - (xy 132.80894 83.010136) (xy 132.808935 83.010132) (xy 132.60195 82.85975) (xy 132.601949 82.859749) - (xy 132.601947 82.859748) (xy 132.508845 82.81231) (xy 132.373975 82.743589) (xy 132.373972 82.743588) - (xy 132.13064 82.664526) (xy 132.004284 82.644513) (xy 131.87793 82.6245) (xy 131.62207 82.6245) - (xy 131.564616 82.6336) (xy 131.369359 82.664526) (xy 131.126027 82.743588) (xy 131.126024 82.743589) - (xy 130.898049 82.85975) (xy 130.691065 83.010131) (xy 130.59908 83.102116) (xy 130.537756 83.1356) - (xy 130.468065 83.130616) (xy 130.412131 83.088744) (xy 130.391626 83.046532) (xy 130.359882 82.92806) - (xy 130.359879 82.928052) (xy 130.270819 82.713039) (xy 130.270811 82.713023) (xy 130.154446 82.511475) - (xy 130.154442 82.511468) (xy 130.012756 82.326819) (xy 130.012751 82.326813) (xy 129.848186 82.162248) - (xy 129.848179 82.162242) (xy 129.66354 82.020564) (xy 129.663538 82.020562) (xy 129.663532 82.020558) - (xy 129.663527 82.020555) (xy 129.663524 82.020553) (xy 129.461976 81.904188) (xy 129.46196 81.90418) - (xy 129.246947 81.81512) (xy 129.18782 81.799277) (xy 129.022126 81.754879) (xy 129.022125 81.754878) - (xy 129.022122 81.754878) (xy 128.791382 81.724501) (xy 128.791377 81.7245) (xy 128.791372 81.7245) - (xy 128.558628 81.7245) (xy 128.558622 81.7245) (xy 128.558617 81.724501) (xy 128.327877 81.754878) - (xy 128.103052 81.81512) (xy 127.888039 81.90418) (xy 127.888023 81.904188) (xy 127.686475 82.020553) - (xy 127.686459 82.020564) (xy 127.50182 82.162242) (xy 127.501813 82.162248) (xy 127.337248 82.326813) - (xy 127.337242 82.32682) (xy 127.195564 82.511459) (xy 127.195553 82.511475) (xy 127.079188 82.713023) - (xy 127.07918 82.713039) (xy 126.99012 82.928052) (xy 126.929878 83.152877) (xy 126.899501 83.383617) - (xy 126.8995 83.383634) (xy 125.5551 83.383634) (xy 125.5551 83.355258) (xy 125.5551 83.355255) - (xy 125.555099 83.355253) (xy 125.524337 83.200603) (xy 125.520383 83.191058) (xy 125.463997 83.054927) - (xy 125.46399 83.054914) (xy 125.376389 82.923811) (xy 125.376386 82.923807) (xy 125.264892 82.812313) - (xy 125.264888 82.81231) (xy 125.133785 82.724709) (xy 125.133772 82.724702) (xy 124.988101 82.664364) - (xy 124.988089 82.664361) (xy 124.833445 82.6336) (xy 124.833442 82.6336) (xy 124.675758 82.6336) - (xy 124.675755 82.6336) (xy 124.52111 82.664361) (xy 124.521098 82.664364) (xy 124.375427 82.724702) - (xy 124.375414 82.724709) (xy 124.244311 82.81231) (xy 124.244307 82.812313) (xy 124.132813 82.923807) - (xy 124.13281 82.923811) (xy 124.045209 83.054914) (xy 124.045202 83.054927) (xy 123.984864 83.200598) - (xy 123.984861 83.20061) (xy 123.9541 83.355253) (xy 120.2505 83.355253) (xy 120.2505 81.443995) - (xy 121.099499 81.443995) (xy 121.126418 81.579322) (xy 121.126421 81.579332) (xy 121.179221 81.706804) - (xy 121.179228 81.706817) (xy 121.255885 81.821541) (xy 121.255888 81.821545) (xy 121.353454 81.919111) - (xy 121.353458 81.919114) (xy 121.468182 81.995771) (xy 121.468195 81.995778) (xy 121.595667 82.048578) - (xy 121.595672 82.04858) (xy 121.595676 82.04858) (xy 121.595677 82.048581) (xy 121.731004 82.0755) - (xy 121.731007 82.0755) (xy 121.868995 82.0755) (xy 121.960041 82.057389) (xy 122.004328 82.04858) - (xy 122.131811 81.995775) (xy 122.246542 81.919114) (xy 122.344114 81.821542) (xy 122.420775 81.706811) - (xy 122.47358 81.579328) (xy 122.484387 81.525) (xy 122.5005 81.443995) (xy 122.5005 81.306004) - (xy 122.473581 81.170677) (xy 122.47358 81.170676) (xy 122.47358 81.170672) (xy 122.460456 81.138988) - (xy 122.420778 81.043195) (xy 122.420771 81.043182) (xy 122.344114 80.928458) (xy 122.344111 80.928454) - (xy 122.246545 80.830888) (xy 122.246541 80.830885) (xy 122.131817 80.754228) (xy 122.131804 80.754221) - (xy 122.004332 80.701421) (xy 122.004322 80.701418) (xy 121.868995 80.6745) (xy 121.868993 80.6745) - (xy 121.731007 80.6745) (xy 121.731005 80.6745) (xy 121.595677 80.701418) (xy 121.595667 80.701421) - (xy 121.468195 80.754221) (xy 121.468182 80.754228) (xy 121.353458 80.830885) (xy 121.353454 80.830888) - (xy 121.255888 80.928454) (xy 121.255885 80.928458) (xy 121.179228 81.043182) (xy 121.179221 81.043195) - (xy 121.126421 81.170667) (xy 121.126418 81.170677) (xy 121.0995 81.306004) (xy 121.0995 81.306007) - (xy 121.0995 81.443993) (xy 121.0995 81.443995) (xy 121.099499 81.443995) (xy 120.2505 81.443995) - (xy 120.2505 80.549853) (xy 125.892 80.549853) (xy 125.892 80.707546) (xy 125.922761 80.862189) - (xy 125.922764 80.862201) (xy 125.983102 81.007872) (xy 125.983109 81.007885) (xy 126.07071 81.138988) - (xy 126.070713 81.138992) (xy 126.182207 81.250486) (xy 126.182211 81.250489) (xy 126.313314 81.33809) - (xy 126.313327 81.338097) (xy 126.458998 81.398435) (xy 126.459003 81.398437) (xy 126.56793 81.420104) - (xy 126.613653 81.429199) (xy 126.613656 81.4292) (xy 126.613658 81.4292) (xy 126.771344 81.4292) - (xy 126.771345 81.429199) (xy 126.925997 81.398437) (xy 127.071679 81.338094) (xy 127.202789 81.250489) - (xy 127.314289 81.138989) (xy 127.401894 81.007879) (xy 127.462237 80.862197) (xy 127.493 80.707542) - (xy 127.493 80.549858) (xy 127.493 80.549855) (xy 127.492999 80.549853) (xy 127.462238 80.39521) - (xy 127.462237 80.395203) (xy 127.462235 80.395198) (xy 127.401897 80.249527) (xy 127.40189 80.249514) - (xy 127.314289 80.118411) (xy 127.314286 80.118407) (xy 127.202792 80.006913) (xy 127.202788 80.00691) - (xy 127.071685 79.919309) (xy 127.071672 79.919302) (xy 126.926001 79.858964) (xy 126.925989 79.858961) - (xy 126.771345 79.8282) (xy 126.771342 79.8282) (xy 126.613658 79.8282) (xy 126.613655 79.8282) - (xy 126.45901 79.858961) (xy 126.458998 79.858964) (xy 126.313327 79.919302) (xy 126.313314 79.919309) - (xy 126.182211 80.00691) (xy 126.182207 80.006913) (xy 126.070713 80.118407) (xy 126.07071 80.118411) - (xy 125.983109 80.249514) (xy 125.983102 80.249527) (xy 125.922764 80.395198) (xy 125.922761 80.39521) - (xy 125.892 80.549853) (xy 120.2505 80.549853) (xy 120.2505 75.693995) (xy 121.099499 75.693995) + (xy 133.25641 83.626025) (xy 133.25641 83.626024) (xy 133.216185 83.54708) (xy 133.140252 83.398053) + (xy 133.061814 83.290092) (xy 132.989867 83.191064) (xy 132.989863 83.191059) (xy 132.80894 83.010136) + (xy 132.808935 83.010132) (xy 132.60195 82.85975) (xy 132.601949 82.859749) (xy 132.601947 82.859748) + (xy 132.52891 82.822533) (xy 132.373975 82.743589) (xy 132.373972 82.743588) (xy 132.13064 82.664526) + (xy 132.004284 82.644513) (xy 131.87793 82.6245) (xy 131.62207 82.6245) (xy 131.537833 82.637842) + (xy 131.369359 82.664526) (xy 131.126027 82.743588) (xy 131.126024 82.743589) (xy 130.898049 82.85975) + (xy 130.691065 83.010131) (xy 130.59908 83.102116) (xy 130.537756 83.1356) (xy 130.468065 83.130616) + (xy 130.412131 83.088744) (xy 130.391626 83.046532) (xy 130.359882 82.92806) (xy 130.359879 82.928052) + (xy 130.270819 82.713039) (xy 130.270811 82.713023) (xy 130.154446 82.511475) (xy 130.154442 82.511468) + (xy 130.012756 82.326819) (xy 130.012751 82.326813) (xy 129.848186 82.162248) (xy 129.848179 82.162242) + (xy 129.66354 82.020564) (xy 129.663538 82.020562) (xy 129.663532 82.020558) (xy 129.663527 82.020555) + (xy 129.663524 82.020553) (xy 129.461976 81.904188) (xy 129.46196 81.90418) (xy 129.246947 81.81512) + (xy 129.18782 81.799277) (xy 129.022126 81.754879) (xy 129.022125 81.754878) (xy 129.022122 81.754878) + (xy 128.791382 81.724501) (xy 128.791377 81.7245) (xy 128.791372 81.7245) (xy 128.558628 81.7245) + (xy 128.558622 81.7245) (xy 128.558617 81.724501) (xy 128.327877 81.754878) (xy 128.103052 81.81512) + (xy 127.888039 81.90418) (xy 127.888023 81.904188) (xy 127.686475 82.020553) (xy 127.686459 82.020564) + (xy 127.50182 82.162242) (xy 127.501813 82.162248) (xy 127.337248 82.326813) (xy 127.337242 82.32682) + (xy 127.195564 82.511459) (xy 127.195553 82.511475) (xy 127.079188 82.713023) (xy 127.07918 82.713039) + (xy 126.99012 82.928052) (xy 126.929878 83.152877) (xy 126.899501 83.383617) (xy 126.8995 83.383634) + (xy 120.2505 83.383634) (xy 120.2505 81.443995) (xy 121.099499 81.443995) (xy 121.126418 81.579322) + (xy 121.126421 81.579332) (xy 121.179221 81.706804) (xy 121.179228 81.706817) (xy 121.255885 81.821541) + (xy 121.255888 81.821545) (xy 121.353454 81.919111) (xy 121.353458 81.919114) (xy 121.468182 81.995771) + (xy 121.468195 81.995778) (xy 121.595667 82.048578) (xy 121.595672 82.04858) (xy 121.595676 82.04858) + (xy 121.595677 82.048581) (xy 121.731004 82.0755) (xy 121.731007 82.0755) (xy 121.868995 82.0755) + (xy 121.960041 82.057389) (xy 122.004328 82.04858) (xy 122.131811 81.995775) (xy 122.246542 81.919114) + (xy 122.344114 81.821542) (xy 122.420775 81.706811) (xy 122.47358 81.579328) (xy 122.484387 81.525) + (xy 122.5005 81.443995) (xy 122.5005 81.306004) (xy 122.473581 81.170677) (xy 122.47358 81.170676) + (xy 122.47358 81.170672) (xy 122.458159 81.133442) (xy 122.420778 81.043195) (xy 122.420771 81.043182) + (xy 122.344114 80.928458) (xy 122.344111 80.928454) (xy 122.246545 80.830888) (xy 122.246541 80.830885) + (xy 122.131817 80.754228) (xy 122.131804 80.754221) (xy 122.004332 80.701421) (xy 122.004322 80.701418) + (xy 121.868995 80.6745) (xy 121.868993 80.6745) (xy 121.731007 80.6745) (xy 121.731005 80.6745) + (xy 121.595677 80.701418) (xy 121.595667 80.701421) (xy 121.468195 80.754221) (xy 121.468182 80.754228) + (xy 121.353458 80.830885) (xy 121.353454 80.830888) (xy 121.255888 80.928454) (xy 121.255885 80.928458) + (xy 121.179228 81.043182) (xy 121.179221 81.043195) (xy 121.126421 81.170667) (xy 121.126418 81.170677) + (xy 121.0995 81.306004) (xy 121.0995 81.306007) (xy 121.0995 81.443993) (xy 121.0995 81.443995) + (xy 121.099499 81.443995) (xy 120.2505 81.443995) (xy 120.2505 75.693995) (xy 121.099499 75.693995) (xy 121.126418 75.829322) (xy 121.126421 75.829332) (xy 121.179221 75.956804) (xy 121.179228 75.956817) (xy 121.255885 76.071541) (xy 121.255888 76.071545) (xy 121.353454 76.169111) (xy 121.353458 76.169114) - (xy 121.468182 76.245771) (xy 121.468195 76.245778) (xy 121.559519 76.283605) (xy 121.595672 76.29858) + (xy 121.468182 76.245771) (xy 121.468195 76.245778) (xy 121.595667 76.298578) (xy 121.595672 76.29858) (xy 121.595676 76.29858) (xy 121.595677 76.298581) (xy 121.731004 76.3255) (xy 121.731007 76.3255) (xy 121.868995 76.3255) (xy 121.960041 76.307389) (xy 122.004328 76.29858) (xy 122.131811 76.245775) (xy 122.246542 76.169114) (xy 122.344114 76.071542) (xy 122.420775 75.956811) (xy 122.47358 75.829328) (xy 122.5005 75.693993) (xy 122.5005 75.556007) (xy 122.5005 75.556004) (xy 122.473581 75.420677) - (xy 122.47358 75.420676) (xy 122.47358 75.420672) (xy 122.465209 75.400463) (xy 122.420778 75.293195) + (xy 122.47358 75.420676) (xy 122.47358 75.420672) (xy 122.470985 75.414406) (xy 122.420778 75.293195) (xy 122.420771 75.293182) (xy 122.344114 75.178458) (xy 122.344111 75.178454) (xy 122.246545 75.080888) (xy 122.246541 75.080885) (xy 122.131817 75.004228) (xy 122.131804 75.004221) (xy 122.004332 74.951421) (xy 122.004322 74.951418) (xy 121.868995 74.9245) (xy 121.868993 74.9245) (xy 121.731007 74.9245) @@ -39490,91 +39963,58 @@ (xy 129.848181 74.837756) (xy 130.012756 74.673181) (xy 130.154442 74.488532) (xy 130.270815 74.286969) (xy 130.359882 74.07194) (xy 130.420121 73.847126) (xy 130.4505 73.616372) (xy 130.4505 73.383628) (xy 130.420121 73.152874) (xy 130.359882 72.92806) (xy 130.359879 72.928052) (xy 130.270819 72.713039) - (xy 130.270811 72.713023) (xy 130.154446 72.511475) (xy 130.154442 72.511468) (xy 130.08363 72.419184) - (xy 130.012757 72.32682) (xy 130.012751 72.326813) (xy 129.848186 72.162248) (xy 129.848179 72.162242) - (xy 129.706396 72.053449) (xy 129.663532 72.020558) (xy 129.663526 72.020554) (xy 129.663524 72.020553) - (xy 129.56064 71.961152) (xy 130.334499 71.961152) (xy 130.334499 72.118845) (xy 130.36526 72.273488) - (xy 130.365263 72.2735) (xy 130.425601 72.419171) (xy 130.425608 72.419184) (xy 130.513209 72.550287) - (xy 130.513212 72.550291) (xy 130.624706 72.661785) (xy 130.62471 72.661788) (xy 130.755813 72.749389) - (xy 130.755826 72.749396) (xy 130.901497 72.809734) (xy 130.901502 72.809736) (xy 131.056152 72.840498) - (xy 131.056155 72.840499) (xy 131.056157 72.840499) (xy 131.213843 72.840499) (xy 131.213844 72.840498) - (xy 131.368496 72.809736) (xy 131.514178 72.749393) (xy 131.645288 72.661788) (xy 131.756788 72.550288) - (xy 131.816347 72.461152) (xy 137.6845 72.461152) (xy 137.6845 72.618845) (xy 137.715261 72.773488) - (xy 137.715264 72.7735) (xy 137.775602 72.919171) (xy 137.775609 72.919184) (xy 137.86321 73.050287) - (xy 137.863213 73.050291) (xy 137.974707 73.161785) (xy 137.974711 73.161788) (xy 138.105814 73.249389) - (xy 138.105827 73.249396) (xy 138.251498 73.309734) (xy 138.251503 73.309736) (xy 138.406153 73.340498) - (xy 138.406156 73.340499) (xy 138.406158 73.340499) (xy 138.563844 73.340499) (xy 138.563845 73.340498) - (xy 138.718497 73.309736) (xy 138.761911 73.291753) (xy 138.826482 73.265008) (xy 138.864172 73.249396) - (xy 138.864172 73.249395) (xy 138.864179 73.249393) (xy 138.995289 73.161788) (xy 139.106789 73.050288) - (xy 139.194394 72.919178) (xy 139.254737 72.773496) (xy 139.2855 72.618841) (xy 139.2855 72.461157) - (xy 139.2855 72.461154) (xy 139.285499 72.461152) (xy 139.274849 72.40761) (xy 139.254737 72.306502) - (xy 139.241062 72.273488) (xy 139.194397 72.160826) (xy 139.19439 72.160813) (xy 139.106789 72.02971) - (xy 139.106786 72.029706) (xy 138.995292 71.918212) (xy 138.995288 71.918209) (xy 138.864185 71.830608) - (xy 138.864172 71.830601) (xy 138.718501 71.770263) (xy 138.718489 71.77026) (xy 138.563845 71.739499) - (xy 138.563842 71.739499) (xy 138.406158 71.739499) (xy 138.406155 71.739499) (xy 138.25151 71.77026) - (xy 138.251498 71.770263) (xy 138.105827 71.830601) (xy 138.105814 71.830608) (xy 137.974711 71.918209) - (xy 137.974707 71.918212) (xy 137.863213 72.029706) (xy 137.86321 72.02971) (xy 137.775609 72.160813) - (xy 137.775602 72.160826) (xy 137.715264 72.306497) (xy 137.715261 72.306509) (xy 137.6845 72.461152) - (xy 131.816347 72.461152) (xy 131.844393 72.419178) (xy 131.904736 72.273496) (xy 131.935499 72.118841) - (xy 131.935499 71.961157) (xy 131.935499 71.961154) (xy 131.935498 71.961152) (xy 131.90953 71.830605) - (xy 131.904736 71.806502) (xy 131.90022 71.795599) (xy 131.844396 71.660826) (xy 131.844389 71.660813) - (xy 131.756788 71.52971) (xy 131.756785 71.529706) (xy 131.671074 71.443995) (xy 147.499499 71.443995) + (xy 130.270814 72.71303) (xy 130.216435 72.618843) (xy 130.154442 72.511468) (xy 130.115833 72.461152) + (xy 137.6845 72.461152) (xy 137.6845 72.618845) (xy 137.715261 72.773488) (xy 137.715264 72.7735) + (xy 137.775602 72.919171) (xy 137.775609 72.919184) (xy 137.86321 73.050287) (xy 137.863213 73.050291) + (xy 137.974707 73.161785) (xy 137.974711 73.161788) (xy 138.105814 73.249389) (xy 138.105827 73.249396) + (xy 138.251498 73.309734) (xy 138.251503 73.309736) (xy 138.406153 73.340498) (xy 138.406156 73.340499) + (xy 138.406158 73.340499) (xy 138.563844 73.340499) (xy 138.563845 73.340498) (xy 138.718497 73.309736) + (xy 138.864179 73.249393) (xy 138.995289 73.161788) (xy 139.106789 73.050288) (xy 139.194394 72.919178) + (xy 139.254737 72.773496) (xy 139.2855 72.618841) (xy 139.2855 72.461157) (xy 139.2855 72.461154) + (xy 139.285499 72.461152) (xy 139.254737 72.306502) (xy 139.254735 72.306497) (xy 139.194397 72.160826) + (xy 139.19439 72.160813) (xy 139.106789 72.02971) (xy 139.106786 72.029706) (xy 138.995292 71.918212) + (xy 138.995288 71.918209) (xy 138.864185 71.830608) (xy 138.864172 71.830601) (xy 138.718501 71.770263) + (xy 138.718489 71.77026) (xy 138.563845 71.739499) (xy 138.563842 71.739499) (xy 138.406158 71.739499) + (xy 138.406155 71.739499) (xy 138.25151 71.77026) (xy 138.251498 71.770263) (xy 138.105827 71.830601) + (xy 138.105814 71.830608) (xy 137.974711 71.918209) (xy 137.974707 71.918212) (xy 137.863213 72.029706) + (xy 137.86321 72.02971) (xy 137.775609 72.160813) (xy 137.775602 72.160826) (xy 137.715264 72.306497) + (xy 137.715261 72.306509) (xy 137.6845 72.461152) (xy 130.115833 72.461152) (xy 130.012756 72.326819) + (xy 130.012751 72.326813) (xy 129.848186 72.162248) (xy 129.848179 72.162242) (xy 129.66354 72.020564) + (xy 129.663538 72.020562) (xy 129.663532 72.020558) (xy 129.663527 72.020555) (xy 129.663524 72.020553) + (xy 129.461976 71.904188) (xy 129.46196 71.90418) (xy 129.246947 71.81512) (xy 129.079539 71.770263) + (xy 129.022126 71.754879) (xy 129.022125 71.754878) (xy 129.022122 71.754878) (xy 128.791382 71.724501) + (xy 128.791377 71.7245) (xy 128.791372 71.7245) (xy 128.558628 71.7245) (xy 128.558622 71.7245) + (xy 128.558617 71.724501) (xy 128.327877 71.754878) (xy 128.103052 71.81512) (xy 127.888039 71.90418) + (xy 127.888023 71.904188) (xy 127.686475 72.020553) (xy 127.686459 72.020564) (xy 127.50182 72.162242) + (xy 127.501813 72.162248) (xy 127.337248 72.326813) (xy 127.337242 72.32682) (xy 127.195564 72.511459) + (xy 127.195553 72.511475) (xy 127.079188 72.713023) (xy 127.07918 72.713039) (xy 126.99012 72.928052) + (xy 126.929878 73.152877) (xy 126.899501 73.383617) (xy 126.8995 73.383634) (xy 120.2505 73.383634) + (xy 120.2505 71.443995) (xy 121.099499 71.443995) (xy 121.126418 71.579322) (xy 121.126421 71.579332) + (xy 121.179221 71.706804) (xy 121.179228 71.706817) (xy 121.255885 71.821541) (xy 121.255888 71.821545) + (xy 121.353454 71.919111) (xy 121.353458 71.919114) (xy 121.468182 71.995771) (xy 121.468195 71.995778) + (xy 121.595667 72.048578) (xy 121.595672 72.04858) (xy 121.595676 72.04858) (xy 121.595677 72.048581) + (xy 121.731004 72.0755) (xy 121.731007 72.0755) (xy 121.868995 72.0755) (xy 121.960041 72.057389) + (xy 122.004328 72.04858) (xy 122.131811 71.995775) (xy 122.246542 71.919114) (xy 122.344114 71.821542) + (xy 122.420775 71.706811) (xy 122.47358 71.579328) (xy 122.5005 71.443995) (xy 147.499499 71.443995) (xy 147.526418 71.579322) (xy 147.526421 71.579332) (xy 147.579221 71.706804) (xy 147.579228 71.706817) (xy 147.655885 71.821541) (xy 147.655888 71.821545) (xy 147.753454 71.919111) (xy 147.753458 71.919114) (xy 147.868182 71.995771) (xy 147.868195 71.995778) (xy 147.995667 72.048578) (xy 147.995672 72.04858) (xy 147.995676 72.04858) (xy 147.995677 72.048581) (xy 148.131004 72.0755) (xy 148.131007 72.0755) - (xy 148.268995 72.0755) (xy 148.37989 72.053441) (xy 148.404328 72.04858) (xy 148.531811 71.995775) - (xy 148.646542 71.919114) (xy 148.744114 71.821542) (xy 148.820775 71.706811) (xy 148.821734 71.704497) - (xy 148.83274 71.677924) (xy 148.87358 71.579328) (xy 148.888287 71.505392) (xy 148.9005 71.443995) - (xy 148.9005 71.306004) (xy 148.873581 71.170677) (xy 148.87358 71.170676) (xy 148.87358 71.170672) - (xy 148.873578 71.170667) (xy 148.820778 71.043195) (xy 148.820771 71.043182) (xy 148.744114 70.928458) - (xy 148.744111 70.928454) (xy 148.646545 70.830888) (xy 148.646541 70.830885) (xy 148.531817 70.754228) - (xy 148.531804 70.754221) (xy 148.404332 70.701421) (xy 148.404322 70.701418) (xy 148.268995 70.6745) - (xy 148.268993 70.6745) (xy 148.131007 70.6745) (xy 148.131005 70.6745) (xy 147.995677 70.701418) - (xy 147.995667 70.701421) (xy 147.868195 70.754221) (xy 147.868182 70.754228) (xy 147.753458 70.830885) - (xy 147.753454 70.830888) (xy 147.655888 70.928454) (xy 147.655885 70.928458) (xy 147.579228 71.043182) - (xy 147.579221 71.043195) (xy 147.526421 71.170667) (xy 147.526418 71.170677) (xy 147.4995 71.306004) - (xy 147.4995 71.306007) (xy 147.4995 71.443993) (xy 147.4995 71.443995) (xy 147.499499 71.443995) - (xy 131.671074 71.443995) (xy 131.645291 71.418212) (xy 131.645287 71.418209) (xy 131.514184 71.330608) - (xy 131.514171 71.330601) (xy 131.3685 71.270263) (xy 131.368488 71.27026) (xy 131.213844 71.239499) - (xy 131.213841 71.239499) (xy 131.056157 71.239499) (xy 131.056154 71.239499) (xy 130.901509 71.27026) - (xy 130.901497 71.270263) (xy 130.755826 71.330601) (xy 130.755813 71.330608) (xy 130.62471 71.418209) - (xy 130.624706 71.418212) (xy 130.513212 71.529706) (xy 130.513209 71.52971) (xy 130.425608 71.660813) - (xy 130.425601 71.660826) (xy 130.365263 71.806497) (xy 130.36526 71.806509) (xy 130.334499 71.961152) - (xy 129.56064 71.961152) (xy 129.461976 71.904188) (xy 129.46196 71.90418) (xy 129.246947 71.81512) - (xy 129.21481 71.806509) (xy 129.022126 71.754879) (xy 129.022125 71.754878) (xy 129.022122 71.754878) - (xy 128.791382 71.724501) (xy 128.791377 71.7245) (xy 128.791372 71.7245) (xy 128.558628 71.7245) - (xy 128.558622 71.7245) (xy 128.558617 71.724501) (xy 128.327877 71.754878) (xy 128.103052 71.81512) - (xy 127.888039 71.90418) (xy 127.888023 71.904188) (xy 127.686475 72.020553) (xy 127.686459 72.020564) - (xy 127.50182 72.162242) (xy 127.501813 72.162248) (xy 127.337248 72.326813) (xy 127.337242 72.32682) - (xy 127.195564 72.511459) (xy 127.195553 72.511475) (xy 127.079188 72.713023) (xy 127.07918 72.713039) - (xy 126.99012 72.928052) (xy 126.929878 73.152877) (xy 126.899501 73.383617) (xy 126.8995 73.383634) - (xy 120.2505 73.383634) (xy 120.2505 71.443995) (xy 121.099499 71.443995) (xy 121.126418 71.579322) - (xy 121.126421 71.579332) (xy 121.179221 71.706804) (xy 121.179228 71.706817) (xy 121.255885 71.821541) - (xy 121.255888 71.821545) (xy 121.353454 71.919111) (xy 121.353458 71.919114) (xy 121.468182 71.995771) - (xy 121.468195 71.995778) (xy 121.595667 72.048578) (xy 121.595672 72.04858) (xy 121.595676 72.04858) - (xy 121.595677 72.048581) (xy 121.731004 72.0755) (xy 121.731007 72.0755) (xy 121.868995 72.0755) - (xy 121.97989 72.053441) (xy 122.004328 72.04858) (xy 122.131811 71.995775) (xy 122.246542 71.919114) - (xy 122.344114 71.821542) (xy 122.420775 71.706811) (xy 122.421734 71.704497) (xy 122.43274 71.677924) - (xy 122.47358 71.579328) (xy 122.488287 71.505392) (xy 122.5005 71.443995) (xy 122.5005 71.306004) - (xy 122.473581 71.170677) (xy 122.47358 71.170676) (xy 122.47358 71.170672) (xy 122.473578 71.170667) - (xy 122.420778 71.043195) (xy 122.420771 71.043182) (xy 122.377924 70.979057) (xy 122.344114 70.928458) - (xy 122.344111 70.928454) (xy 122.33191 70.916253) (xy 125.2034 70.916253) (xy 125.2034 71.073946) - (xy 125.234161 71.228589) (xy 125.234164 71.228601) (xy 125.294502 71.374272) (xy 125.294509 71.374285) - (xy 125.38211 71.505388) (xy 125.382113 71.505392) (xy 125.493607 71.616886) (xy 125.493611 71.616889) - (xy 125.624714 71.70449) (xy 125.624727 71.704497) (xy 125.746362 71.754879) (xy 125.770403 71.764837) - (xy 125.925053 71.795599) (xy 125.925056 71.7956) (xy 125.925058 71.7956) (xy 126.082744 71.7956) - (xy 126.082745 71.795599) (xy 126.237397 71.764837) (xy 126.383079 71.704494) (xy 126.514189 71.616889) - (xy 126.625689 71.505389) (xy 126.713294 71.374279) (xy 126.773637 71.228597) (xy 126.8044 71.073942) - (xy 126.8044 70.916258) (xy 126.8044 70.916255) (xy 126.804399 70.916253) (xy 126.774325 70.765063) - (xy 126.773637 70.761603) (xy 126.72528 70.644857) (xy 126.713297 70.615927) (xy 126.71329 70.615914) - (xy 126.625689 70.484811) (xy 126.625686 70.484807) (xy 126.514192 70.373313) (xy 126.514188 70.37331) - (xy 126.383085 70.285709) (xy 126.383072 70.285702) (xy 126.237401 70.225364) (xy 126.237389 70.225361) - (xy 126.082745 70.1946) (xy 126.082742 70.1946) (xy 125.925058 70.1946) (xy 125.925055 70.1946) - (xy 125.77041 70.225361) (xy 125.770398 70.225364) (xy 125.624727 70.285702) (xy 125.624714 70.285709) - (xy 125.493611 70.37331) (xy 125.493607 70.373313) (xy 125.382113 70.484807) (xy 125.38211 70.484811) - (xy 125.294509 70.615914) (xy 125.294502 70.615927) (xy 125.234164 70.761598) (xy 125.234161 70.76161) - (xy 125.2034 70.916253) (xy 122.33191 70.916253) (xy 122.246545 70.830888) (xy 122.246541 70.830885) + (xy 148.268995 72.0755) (xy 148.360041 72.057389) (xy 148.404328 72.04858) (xy 148.531811 71.995775) + (xy 148.646542 71.919114) (xy 148.744114 71.821542) (xy 148.820775 71.706811) (xy 148.87358 71.579328) + (xy 148.9005 71.443993) (xy 148.9005 71.306007) (xy 148.9005 71.306004) (xy 148.873581 71.170677) + (xy 148.87358 71.170676) (xy 148.87358 71.170672) (xy 148.873578 71.170667) (xy 148.820778 71.043195) + (xy 148.820771 71.043182) (xy 148.744114 70.928458) (xy 148.744111 70.928454) (xy 148.646545 70.830888) + (xy 148.646541 70.830885) (xy 148.531817 70.754228) (xy 148.531804 70.754221) (xy 148.404332 70.701421) + (xy 148.404322 70.701418) (xy 148.268995 70.6745) (xy 148.268993 70.6745) (xy 148.131007 70.6745) + (xy 148.131005 70.6745) (xy 147.995677 70.701418) (xy 147.995667 70.701421) (xy 147.868195 70.754221) + (xy 147.868182 70.754228) (xy 147.753458 70.830885) (xy 147.753454 70.830888) (xy 147.655888 70.928454) + (xy 147.655885 70.928458) (xy 147.579228 71.043182) (xy 147.579221 71.043195) (xy 147.526421 71.170667) + (xy 147.526418 71.170677) (xy 147.4995 71.306004) (xy 147.4995 71.306007) (xy 147.4995 71.443993) + (xy 147.4995 71.443995) (xy 147.499499 71.443995) (xy 122.5005 71.443995) (xy 122.5005 71.443993) + (xy 122.5005 71.306007) (xy 122.5005 71.306004) (xy 122.473581 71.170677) (xy 122.47358 71.170676) + (xy 122.47358 71.170672) (xy 122.473578 71.170667) (xy 122.420778 71.043195) (xy 122.420771 71.043182) + (xy 122.344114 70.928458) (xy 122.344111 70.928454) (xy 122.246545 70.830888) (xy 122.246541 70.830885) (xy 122.131817 70.754228) (xy 122.131804 70.754221) (xy 122.004332 70.701421) (xy 122.004322 70.701418) (xy 121.868995 70.6745) (xy 121.868993 70.6745) (xy 121.731007 70.6745) (xy 121.731005 70.6745) (xy 121.595677 70.701418) (xy 121.595667 70.701421) (xy 121.468195 70.754221) (xy 121.468182 70.754228) @@ -39582,7 +40022,7 @@ (xy 121.179228 71.043182) (xy 121.179221 71.043195) (xy 121.126421 71.170667) (xy 121.126418 71.170677) (xy 121.0995 71.306004) (xy 121.0995 71.306007) (xy 121.0995 71.443993) (xy 121.0995 71.443995) (xy 121.099499 71.443995) (xy 120.2505 71.443995) (xy 120.2505 69.649941) (xy 130.9745 69.649941) - (xy 130.9745 69.890058) (xy 131.012063 70.127222) (xy 131.086265 70.355593) (xy 131.152104 70.484807) + (xy 130.9745 69.890058) (xy 131.012063 70.127222) (xy 131.086265 70.355593) (xy 131.195143 70.569274) (xy 131.195276 70.569536) (xy 131.336414 70.763796) (xy 131.506204 70.933586) (xy 131.700464 71.074724) (xy 131.801543 71.126226) (xy 131.914406 71.183734) (xy 131.914408 71.183734) (xy 131.914411 71.183736) (xy 132.142778 71.257937) (xy 132.379941 71.2955) (xy 132.379942 71.2955) (xy 132.620058 71.2955) @@ -39617,37 +40057,37 @@ (xy 132.857222 68.282063) (xy 132.620059 68.2445) (xy 132.379941 68.2445) (xy 132.261359 68.263281) (xy 132.142777 68.282063) (xy 131.914406 68.356265) (xy 131.700463 68.465276) (xy 131.506201 68.606416) (xy 131.336416 68.776201) (xy 131.195276 68.970463) (xy 131.086265 69.184406) (xy 131.012063 69.412777) - (xy 130.9745 69.649941) (xy 120.2505 69.649941) (xy 120.2505 66.773453) (xy 126.4602 66.773453) - (xy 126.4602 66.931146) (xy 126.490961 67.085789) (xy 126.490964 67.085801) (xy 126.551302 67.231472) - (xy 126.551309 67.231485) (xy 126.63891 67.362588) (xy 126.638913 67.362592) (xy 126.750407 67.474086) - (xy 126.750411 67.474089) (xy 126.881514 67.56169) (xy 126.881527 67.561697) (xy 127.027198 67.622035) - (xy 127.027203 67.622037) (xy 127.181853 67.652799) (xy 127.181856 67.6528) (xy 127.181858 67.6528) - (xy 127.339544 67.6528) (xy 127.339545 67.652799) (xy 127.494197 67.622037) (xy 127.639879 67.561694) - (xy 127.770989 67.474089) (xy 127.882489 67.362589) (xy 127.970094 67.231479) (xy 128.030437 67.085797) - (xy 128.0612 66.931142) (xy 128.0612 66.773458) (xy 128.0612 66.773455) (xy 128.061199 66.773453) - (xy 128.030438 66.61881) (xy 128.030437 66.618803) (xy 128.030435 66.618798) (xy 127.970097 66.473127) - (xy 127.97009 66.473114) (xy 127.882489 66.342011) (xy 127.882486 66.342007) (xy 127.770992 66.230513) - (xy 127.770988 66.23051) (xy 127.639885 66.142909) (xy 127.639872 66.142902) (xy 127.494201 66.082564) - (xy 127.494189 66.082561) (xy 127.339545 66.0518) (xy 127.339542 66.0518) (xy 127.181858 66.0518) - (xy 127.181855 66.0518) (xy 127.02721 66.082561) (xy 127.027198 66.082564) (xy 126.881527 66.142902) - (xy 126.881514 66.142909) (xy 126.750411 66.23051) (xy 126.750407 66.230513) (xy 126.638913 66.342007) - (xy 126.63891 66.342011) (xy 126.551309 66.473114) (xy 126.551302 66.473127) (xy 126.490964 66.618798) - (xy 126.490961 66.61881) (xy 126.4602 66.773453) (xy 120.2505 66.773453) (xy 120.2505 65.573253) - (xy 131.4543 65.573253) (xy 131.4543 65.730946) (xy 131.485061 65.885589) (xy 131.485064 65.885601) - (xy 131.545402 66.031272) (xy 131.545409 66.031285) (xy 131.63301 66.162388) (xy 131.633013 66.162392) - (xy 131.744507 66.273886) (xy 131.744511 66.273889) (xy 131.875614 66.36149) (xy 131.875627 66.361497) - (xy 132.021298 66.421835) (xy 132.021303 66.421837) (xy 132.175953 66.452599) (xy 132.175956 66.4526) - (xy 132.175958 66.4526) (xy 132.333644 66.4526) (xy 132.333645 66.452599) (xy 132.488297 66.421837) - (xy 132.633979 66.361494) (xy 132.765089 66.273889) (xy 132.876589 66.162389) (xy 132.964194 66.031279) - (xy 133.024537 65.885597) (xy 133.0553 65.730942) (xy 133.0553 65.573258) (xy 133.0553 65.573255) - (xy 133.055299 65.573253) (xy 133.024538 65.41861) (xy 133.024537 65.418603) (xy 133.024535 65.418598) - (xy 132.964197 65.272927) (xy 132.96419 65.272914) (xy 132.876589 65.141811) (xy 132.876586 65.141807) - (xy 132.765092 65.030313) (xy 132.765088 65.03031) (xy 132.633985 64.942709) (xy 132.633972 64.942702) - (xy 132.488301 64.882364) (xy 132.488289 64.882361) (xy 132.333645 64.8516) (xy 132.333642 64.8516) - (xy 132.175958 64.8516) (xy 132.175955 64.8516) (xy 132.02131 64.882361) (xy 132.021298 64.882364) - (xy 131.875627 64.942702) (xy 131.875614 64.942709) (xy 131.744511 65.03031) (xy 131.744507 65.030313) - (xy 131.633013 65.141807) (xy 131.63301 65.141811) (xy 131.545409 65.272914) (xy 131.545402 65.272927) - (xy 131.485064 65.418598) (xy 131.485061 65.41861) (xy 131.4543 65.573253) (xy 120.2505 65.573253) + (xy 130.9745 69.649941) (xy 120.2505 69.649941) (xy 120.2505 67.721153) (xy 123.6995 67.721153) + (xy 123.6995 67.878846) (xy 123.730261 68.033489) (xy 123.730264 68.033501) (xy 123.790602 68.179172) + (xy 123.790609 68.179185) (xy 123.87821 68.310288) (xy 123.878213 68.310292) (xy 123.989707 68.421786) + (xy 123.989711 68.421789) (xy 124.120814 68.50939) (xy 124.120827 68.509397) (xy 124.266498 68.569735) + (xy 124.266503 68.569737) (xy 124.421153 68.600499) (xy 124.421156 68.6005) (xy 124.421158 68.6005) + (xy 124.578844 68.6005) (xy 124.578845 68.600499) (xy 124.733497 68.569737) (xy 124.879179 68.509394) + (xy 125.010289 68.421789) (xy 125.121789 68.310289) (xy 125.209394 68.179179) (xy 125.269737 68.033497) + (xy 125.3005 67.878842) (xy 125.3005 67.721158) (xy 125.3005 67.721155) (xy 125.300499 67.721153) + (xy 125.269738 67.56651) (xy 125.269737 67.566503) (xy 125.269735 67.566498) (xy 125.209397 67.420827) + (xy 125.20939 67.420814) (xy 125.121789 67.289711) (xy 125.121786 67.289707) (xy 125.010292 67.178213) + (xy 125.010288 67.17821) (xy 124.879185 67.090609) (xy 124.879172 67.090602) (xy 124.733501 67.030264) + (xy 124.733489 67.030261) (xy 124.578845 66.9995) (xy 124.578842 66.9995) (xy 124.421158 66.9995) + (xy 124.421155 66.9995) (xy 124.26651 67.030261) (xy 124.266498 67.030264) (xy 124.120827 67.090602) + (xy 124.120814 67.090609) (xy 123.989711 67.17821) (xy 123.989707 67.178213) (xy 123.878213 67.289707) + (xy 123.87821 67.289711) (xy 123.790609 67.420814) (xy 123.790602 67.420827) (xy 123.730264 67.566498) + (xy 123.730261 67.56651) (xy 123.6995 67.721153) (xy 120.2505 67.721153) (xy 120.2505 64.521153) + (xy 128.1995 64.521153) (xy 128.1995 64.678846) (xy 128.230261 64.833489) (xy 128.230264 64.833501) + (xy 128.290602 64.979172) (xy 128.290609 64.979185) (xy 128.37821 65.110288) (xy 128.378213 65.110292) + (xy 128.489707 65.221786) (xy 128.489711 65.221789) (xy 128.620814 65.30939) (xy 128.620827 65.309397) + (xy 128.766498 65.369735) (xy 128.766503 65.369737) (xy 128.921153 65.400499) (xy 128.921156 65.4005) + (xy 128.921158 65.4005) (xy 129.078844 65.4005) (xy 129.078845 65.400499) (xy 129.233497 65.369737) + (xy 129.379179 65.309394) (xy 129.510289 65.221789) (xy 129.621789 65.110289) (xy 129.709394 64.979179) + (xy 129.769737 64.833497) (xy 129.8005 64.678842) (xy 129.8005 64.521158) (xy 129.8005 64.521155) + (xy 129.800499 64.521153) (xy 129.769738 64.36651) (xy 129.769737 64.366503) (xy 129.769735 64.366498) + (xy 129.709397 64.220827) (xy 129.70939 64.220814) (xy 129.621789 64.089711) (xy 129.621786 64.089707) + (xy 129.510292 63.978213) (xy 129.510288 63.97821) (xy 129.379185 63.890609) (xy 129.379172 63.890602) + (xy 129.233501 63.830264) (xy 129.233489 63.830261) (xy 129.078845 63.7995) (xy 129.078842 63.7995) + (xy 128.921158 63.7995) (xy 128.921155 63.7995) (xy 128.76651 63.830261) (xy 128.766498 63.830264) + (xy 128.620827 63.890602) (xy 128.620814 63.890609) (xy 128.489711 63.97821) (xy 128.489707 63.978213) + (xy 128.378213 64.089707) (xy 128.37821 64.089711) (xy 128.290609 64.220814) (xy 128.290602 64.220827) + (xy 128.230264 64.366498) (xy 128.230261 64.36651) (xy 128.1995 64.521153) (xy 120.2505 64.521153) (xy 120.2505 62.493713) (xy 121.1495 62.493713) (xy 121.1495 62.706287) (xy 121.182754 62.916243) (xy 121.247738 63.116243) (xy 121.248444 63.118414) (xy 121.344951 63.30782) (xy 121.46989 63.479786) (xy 121.620213 63.630109) (xy 121.792179 63.755048) (xy 121.792181 63.755049) (xy 121.792184 63.755051) @@ -39656,8 +40096,15 @@ (xy 123.207816 63.755051) (xy 123.311402 63.679792) (xy 123.379786 63.630109) (xy 123.379788 63.630106) (xy 123.379792 63.630104) (xy 123.530104 63.479792) (xy 123.530106 63.479788) (xy 123.530109 63.479786) (xy 123.655048 63.30782) (xy 123.655047 63.30782) (xy 123.655051 63.307816) (xy 123.751557 63.118412) - (xy 123.817246 62.916243) (xy 123.8505 62.706287) (xy 123.8505 62.693713) (xy 146.0495 62.693713) - (xy 146.0495 62.906287) (xy 146.082754 63.116243) (xy 146.145001 63.30782) (xy 146.148444 63.318414) + (xy 123.817246 62.916243) (xy 123.8505 62.706287) (xy 123.8505 62.621153) (xy 130.1995 62.621153) + (xy 130.1995 62.778846) (xy 130.230261 62.933489) (xy 130.230264 62.933501) (xy 130.290602 63.079172) + (xy 130.290609 63.079185) (xy 130.37821 63.210288) (xy 130.378213 63.210292) (xy 130.489707 63.321786) + (xy 130.489711 63.321789) (xy 130.620814 63.40939) (xy 130.620827 63.409397) (xy 130.766498 63.469735) + (xy 130.766503 63.469737) (xy 130.921153 63.500499) (xy 130.921156 63.5005) (xy 130.921158 63.5005) + (xy 131.078844 63.5005) (xy 131.078845 63.500499) (xy 131.233497 63.469737) (xy 131.379179 63.409394) + (xy 131.510289 63.321789) (xy 131.621789 63.210289) (xy 131.709394 63.079179) (xy 131.769737 62.933497) + (xy 131.8005 62.778842) (xy 131.8005 62.693713) (xy 146.0495 62.693713) (xy 146.0495 62.906286) + (xy 146.076884 63.079185) (xy 146.082754 63.116243) (xy 146.145001 63.30782) (xy 146.148444 63.318414) (xy 146.244951 63.50782) (xy 146.36989 63.679786) (xy 146.520213 63.830109) (xy 146.692179 63.955048) (xy 146.692181 63.955049) (xy 146.692184 63.955051) (xy 146.881588 64.051557) (xy 147.083757 64.117246) (xy 147.293713 64.1505) (xy 147.293714 64.1505) (xy 147.506286 64.1505) (xy 147.506287 64.1505) @@ -39671,33 +40118,57 @@ (xy 147.716243 61.482754) (xy 147.716241 61.482753) (xy 147.71624 61.482753) (xy 147.554957 61.457208) (xy 147.506287 61.4495) (xy 147.293713 61.4495) (xy 147.245042 61.457208) (xy 147.08376 61.482753) (xy 146.881585 61.548444) (xy 146.692179 61.644951) (xy 146.520213 61.76989) (xy 146.36989 61.920213) - (xy 146.244951 62.092179) (xy 146.148444 62.281585) (xy 146.082753 62.48376) (xy 146.081177 62.493713) - (xy 146.0495 62.693713) (xy 123.8505 62.693713) (xy 123.8505 62.493713) (xy 123.817246 62.283757) - (xy 123.751557 62.081588) (xy 123.655051 61.892184) (xy 123.638203 61.868995) (xy 132.174499 61.868995) - (xy 132.201418 62.004322) (xy 132.201421 62.004332) (xy 132.254221 62.131804) (xy 132.254228 62.131817) - (xy 132.330885 62.246541) (xy 132.330888 62.246545) (xy 132.428454 62.344111) (xy 132.428458 62.344114) - (xy 132.543182 62.420771) (xy 132.543195 62.420778) (xy 132.670667 62.473578) (xy 132.670672 62.47358) - (xy 132.670676 62.47358) (xy 132.670677 62.473581) (xy 132.806004 62.5005) (xy 132.806007 62.5005) - (xy 132.943995 62.5005) (xy 133.035041 62.482389) (xy 133.079328 62.47358) (xy 133.206811 62.420775) - (xy 133.321542 62.344114) (xy 133.419114 62.246542) (xy 133.495775 62.131811) (xy 133.54858 62.004328) - (xy 133.5755 61.868993) (xy 133.5755 61.731007) (xy 133.5755 61.731004) (xy 133.548581 61.595677) - (xy 133.54858 61.595676) (xy 133.54858 61.595672) (xy 133.510029 61.502601) (xy 133.495778 61.468195) - (xy 133.495771 61.468182) (xy 133.419114 61.353458) (xy 133.419111 61.353454) (xy 133.321545 61.255888) - (xy 133.321541 61.255885) (xy 133.206817 61.179228) (xy 133.206804 61.179221) (xy 133.079332 61.126421) - (xy 133.079322 61.126418) (xy 132.943995 61.0995) (xy 132.943993 61.0995) (xy 132.806007 61.0995) - (xy 132.806005 61.0995) (xy 132.670677 61.126418) (xy 132.670667 61.126421) (xy 132.543195 61.179221) - (xy 132.543182 61.179228) (xy 132.428458 61.255885) (xy 132.428454 61.255888) (xy 132.330888 61.353454) - (xy 132.330885 61.353458) (xy 132.254228 61.468182) (xy 132.254221 61.468195) (xy 132.201421 61.595667) - (xy 132.201418 61.595677) (xy 132.1745 61.731004) (xy 132.1745 61.731007) (xy 132.1745 61.868993) - (xy 132.1745 61.868995) (xy 132.174499 61.868995) (xy 123.638203 61.868995) (xy 123.530104 61.720208) - (xy 123.379792 61.569896) (xy 123.379786 61.56989) (xy 123.20782 61.444951) (xy 123.018414 61.348444) - (xy 123.018413 61.348443) (xy 123.018412 61.348443) (xy 122.816243 61.282754) (xy 122.816241 61.282753) - (xy 122.81624 61.282753) (xy 122.6466 61.255885) (xy 122.606287 61.2495) (xy 122.393713 61.2495) - (xy 122.3534 61.255885) (xy 122.18376 61.282753) (xy 121.981585 61.348444) (xy 121.792179 61.444951) - (xy 121.620213 61.56989) (xy 121.46989 61.720213) (xy 121.344951 61.892179) (xy 121.248444 62.081585) - (xy 121.182753 62.28376) (xy 121.173194 62.344114) (xy 121.1495 62.493713) (xy 120.2505 62.493713) - (xy 120.2505 60.3745) (xy 120.270185 60.307461) (xy 120.322989 60.261706) (xy 120.3745 60.2505) - (xy 134.758628 60.2505) + (xy 146.244951 62.092179) (xy 146.148444 62.281585) (xy 146.082753 62.48376) (xy 146.0495 62.693713) + (xy 131.8005 62.693713) (xy 131.8005 62.621158) (xy 131.8005 62.621155) (xy 131.800499 62.621153) + (xy 131.775149 62.493713) (xy 131.769737 62.466503) (xy 131.750796 62.420775) (xy 131.709397 62.320827) + (xy 131.70939 62.320814) (xy 131.621789 62.189711) (xy 131.621786 62.189707) (xy 131.510292 62.078213) + (xy 131.510288 62.07821) (xy 131.379185 61.990609) (xy 131.379172 61.990602) (xy 131.233501 61.930264) + (xy 131.233489 61.930261) (xy 131.078845 61.8995) (xy 131.078842 61.8995) (xy 130.921158 61.8995) + (xy 130.921155 61.8995) (xy 130.76651 61.930261) (xy 130.766498 61.930264) (xy 130.620827 61.990602) + (xy 130.620814 61.990609) (xy 130.489711 62.07821) (xy 130.489707 62.078213) (xy 130.378213 62.189707) + (xy 130.37821 62.189711) (xy 130.290609 62.320814) (xy 130.290602 62.320827) (xy 130.230264 62.466498) + (xy 130.230261 62.46651) (xy 130.1995 62.621153) (xy 123.8505 62.621153) (xy 123.8505 62.493713) + (xy 123.817246 62.283757) (xy 123.751557 62.081588) (xy 123.655051 61.892184) (xy 123.638203 61.868995) + (xy 132.174499 61.868995) (xy 132.201418 62.004322) (xy 132.201421 62.004332) (xy 132.254221 62.131804) + (xy 132.254228 62.131817) (xy 132.330885 62.246541) (xy 132.330888 62.246545) (xy 132.428454 62.344111) + (xy 132.428458 62.344114) (xy 132.543182 62.420771) (xy 132.543195 62.420778) (xy 132.653603 62.46651) + (xy 132.670672 62.47358) (xy 132.670676 62.47358) (xy 132.670677 62.473581) (xy 132.806004 62.5005) + (xy 132.806007 62.5005) (xy 132.943995 62.5005) (xy 133.035041 62.482389) (xy 133.079328 62.47358) + (xy 133.206811 62.420775) (xy 133.321542 62.344114) (xy 133.419114 62.246542) (xy 133.495775 62.131811) + (xy 133.54858 62.004328) (xy 133.5755 61.868995) (xy 136.424499 61.868995) (xy 136.451418 62.004322) + (xy 136.451421 62.004332) (xy 136.504221 62.131804) (xy 136.504228 62.131817) (xy 136.580885 62.246541) + (xy 136.580888 62.246545) (xy 136.678454 62.344111) (xy 136.678458 62.344114) (xy 136.793182 62.420771) + (xy 136.793195 62.420778) (xy 136.903603 62.46651) (xy 136.920672 62.47358) (xy 136.920676 62.47358) + (xy 136.920677 62.473581) (xy 137.056004 62.5005) (xy 137.056007 62.5005) (xy 137.193995 62.5005) + (xy 137.285041 62.482389) (xy 137.329328 62.47358) (xy 137.456811 62.420775) (xy 137.571542 62.344114) + (xy 137.669114 62.246542) (xy 137.745775 62.131811) (xy 137.79858 62.004328) (xy 137.8255 61.868993) + (xy 137.8255 61.731007) (xy 137.8255 61.731004) (xy 137.798581 61.595677) (xy 137.79858 61.595676) + (xy 137.79858 61.595672) (xy 137.751808 61.482753) (xy 137.745778 61.468195) (xy 137.745771 61.468182) + (xy 137.669114 61.353458) (xy 137.669111 61.353454) (xy 137.571545 61.255888) (xy 137.571541 61.255885) + (xy 137.456817 61.179228) (xy 137.456804 61.179221) (xy 137.329332 61.126421) (xy 137.329322 61.126418) + (xy 137.193995 61.0995) (xy 137.193993 61.0995) (xy 137.056007 61.0995) (xy 137.056005 61.0995) + (xy 136.920677 61.126418) (xy 136.920667 61.126421) (xy 136.793195 61.179221) (xy 136.793182 61.179228) + (xy 136.678458 61.255885) (xy 136.678454 61.255888) (xy 136.580888 61.353454) (xy 136.580885 61.353458) + (xy 136.504228 61.468182) (xy 136.504221 61.468195) (xy 136.451421 61.595667) (xy 136.451418 61.595677) + (xy 136.4245 61.731004) (xy 136.4245 61.731007) (xy 136.4245 61.868993) (xy 136.4245 61.868995) + (xy 136.424499 61.868995) (xy 133.5755 61.868995) (xy 133.5755 61.868993) (xy 133.5755 61.731007) + (xy 133.5755 61.731004) (xy 133.548581 61.595677) (xy 133.54858 61.595676) (xy 133.54858 61.595672) + (xy 133.501808 61.482753) (xy 133.495778 61.468195) (xy 133.495771 61.468182) (xy 133.419114 61.353458) + (xy 133.419111 61.353454) (xy 133.321545 61.255888) (xy 133.321541 61.255885) (xy 133.206817 61.179228) + (xy 133.206804 61.179221) (xy 133.079332 61.126421) (xy 133.079322 61.126418) (xy 132.943995 61.0995) + (xy 132.943993 61.0995) (xy 132.806007 61.0995) (xy 132.806005 61.0995) (xy 132.670677 61.126418) + (xy 132.670667 61.126421) (xy 132.543195 61.179221) (xy 132.543182 61.179228) (xy 132.428458 61.255885) + (xy 132.428454 61.255888) (xy 132.330888 61.353454) (xy 132.330885 61.353458) (xy 132.254228 61.468182) + (xy 132.254221 61.468195) (xy 132.201421 61.595667) (xy 132.201418 61.595677) (xy 132.1745 61.731004) + (xy 132.1745 61.731007) (xy 132.1745 61.868993) (xy 132.1745 61.868995) (xy 132.174499 61.868995) + (xy 123.638203 61.868995) (xy 123.530104 61.720208) (xy 123.379792 61.569896) (xy 123.379786 61.56989) + (xy 123.20782 61.444951) (xy 123.018414 61.348444) (xy 123.018413 61.348443) (xy 123.018412 61.348443) + (xy 122.816243 61.282754) (xy 122.816241 61.282753) (xy 122.81624 61.282753) (xy 122.6466 61.255885) + (xy 122.606287 61.2495) (xy 122.393713 61.2495) (xy 122.3534 61.255885) (xy 122.18376 61.282753) + (xy 121.981585 61.348444) (xy 121.792179 61.444951) (xy 121.620213 61.56989) (xy 121.46989 61.720213) + (xy 121.344951 61.892179) (xy 121.248444 62.081585) (xy 121.182753 62.28376) (xy 121.152689 62.473578) + (xy 121.1495 62.493713) (xy 120.2505 62.493713) (xy 120.2505 60.3745) (xy 120.270185 60.307461) + (xy 120.322989 60.261706) (xy 120.3745 60.2505) (xy 149.6255 60.2505) ) ) ) diff --git a/PCB/v2.x/snips_controller.kicad_pro b/PCB/v2.x/snips_controller.kicad_pro index 82c5ecc..f5de472 100644 --- a/PCB/v2.x/snips_controller.kicad_pro +++ b/PCB/v2.x/snips_controller.kicad_pro @@ -569,10 +569,6 @@ { "netclass": "Power", "pattern": "VSYS" - }, - { - "netclass": "Power", - "pattern": "/MCU_Core/3V3_RF" } ] }, diff --git a/PCB/v2.x/stackup/board.kdl b/PCB/v2.x/stackup/board.kdl index 70dcdb6..32fae5e 100644 --- a/PCB/v2.x/stackup/board.kdl +++ b/PCB/v2.x/stackup/board.kdl @@ -20,9 +20,11 @@ design snips_controller { place jst-ph-2 "BT1" designator="BT1" footprint="Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal" value="PH 2-pin battery RIGHT-ANGLE HORIZONTAL" place capacitor "C_3V3_1" designator="C_3V3_1" footprint="Capacitor_SMD:C_0603_1608Metric" value="10µF" place capacitor "C_3V3_2" designator="C_3V3_2" footprint="Capacitor_SMD:C_0402_1005Metric" value="100nF" + place capacitor "C_3V3_3" designator="C_3V3_3" footprint="Capacitor_SMD:C_0402_1005Metric" value="39pF" place capacitor "C_BAT1" designator="C_BAT1" footprint="Capacitor_SMD:C_0805_2012Metric" value="10µF" place capacitor "C_BUCK_IN1" designator="C_BUCK_IN1" footprint="Capacitor_SMD:C_0805_2012Metric" value="10µF" - place capacitor "C_BUCK_OUT1" designator="C_BUCK_OUT1" footprint="Capacitor_SMD:C_0805_2012Metric" value="10µF" + place capacitor "C_BUCK_OUT1" designator="C_BUCK_OUT1" footprint="Capacitor_SMD:C_0805_2012Metric" value="22µF" + place capacitor "C_EN1" designator="C_EN1" footprint="Capacitor_SMD:C_0603_1608Metric" value="1µF" place capacitor "C_DBNC1" designator="C_DBNC1" footprint="Capacitor_SMD:C_0402_1005Metric" value="100nF" place capacitor "C_IMU_1" designator="C_IMU_1" footprint="Capacitor_SMD:C_0402_1005Metric" value="100nF" place capacitor "C_IMU_2" designator="C_IMU_2" footprint="Capacitor_SMD:C_0603_1608Metric" value="2.2µF" @@ -54,6 +56,7 @@ design snips_controller { place resistor "R_BTN_PU1" designator="R_BTN_PU1" footprint="Resistor_SMD:R_0402_1005Metric" value="100kΩ" place resistor "R_CC1" designator="R_CC1" footprint="Resistor_SMD:R_0402_1005Metric" value="5.1kΩ" place resistor "R_CC2" designator="R_CC2" footprint="Resistor_SMD:R_0402_1005Metric" value="5.1kΩ" + place resistor "R_EN_PU1" designator="R_EN_PU1" footprint="Resistor_SMD:R_0402_1005Metric" value="10kΩ" place resistor "R_FB1" designator="R_FB1" footprint="Resistor_SMD:R_0402_1005Metric" value="255kΩ" place resistor "R_FB2" designator="R_FB2" footprint="Resistor_SMD:R_0402_1005Metric" value="56.2kΩ" place resistor "R_GATE1" designator="R_GATE1" footprint="Resistor_SMD:R_0402_1005Metric" value="100kΩ" @@ -66,12 +69,12 @@ design snips_controller { place resistor "R_STAT1" designator="R_STAT1" footprint="Resistor_SMD:R_0402_1005Metric" value="10kΩ" place resistor "R_STAT2" designator="R_STAT2" footprint="Resistor_SMD:R_0402_1005Metric" value="10kΩ" place resistor "R_TS1" designator="R_TS1" footprint="Resistor_SMD:R_0402_1005Metric" value="10kΩ" + place resistor "R_USB_DM1" designator="R_USB_DM1" footprint="Resistor_SMD:R_0402_1005Metric" value="27Ω" + place resistor "R_USB_DP1" designator="R_USB_DP1" footprint="Resistor_SMD:R_0402_1005Metric" value="27Ω" place resistor "R_VSET1" designator="R_VSET1" footprint="Resistor_SMD:R_0402_1005Metric" value="18kΩ" place resistor "R_VSYS1" designator="R_VSYS1" footprint="Resistor_SMD:R_0402_1005Metric" value="200kΩ" place resistor "R_VSYS2" designator="R_VSYS2" footprint="Resistor_SMD:R_0402_1005Metric" value="100kΩ" place skrp-button "SW_BOOT1" designator="SW_BOOT1" footprint="SnipsControllers_Custom:SW_Alps_SKRP" value="SKRPABE010" - // Forces the board off when firmware hangs with PWR_HOLD high, since the power button can only turn it on. - place skrp-button "SW_RST1" designator="SW_RST1" footprint="SnipsControllers_Custom:SW_Alps_SKRP" value="SKRPABE010" place skrp-button "SW_MACRO1" designator="SW_MACRO1" footprint="SnipsControllers_Custom:SW_Alps_SKRP" value="SKRPABE010" place skrp-button "SW_MACRO2" designator="SW_MACRO2" footprint="SnipsControllers_Custom:SW_Alps_SKRP" value="SKRPABE010" place skrp-button "SW_MACRO3" designator="SW_MACRO3" footprint="SnipsControllers_Custom:SW_Alps_SKRP" value="SKRPABE010" @@ -86,60 +89,63 @@ design snips_controller { place push-button "SW_VOL_UP1" designator="SW_VOL_UP1" footprint="Button_Switch_SMD:SW_Push_1P1T-MP_NO_Horizontal_Alps_SKRTLAE010" package="alps" value="SKRTLAE010" place tlv62569 "U_BUCK1" designator="U_BUCK1" footprint="Package_TO_SOT_SMD:SOT-23-5" value="TLV62569DBVR" place bq25185 "U_CHG1" designator="U_CHG1" footprint="BQ25185DLHR:IC_BQ25185DLHR" value="BQ25185DLHR" { without program; without always-enabled; without ts-fixed; without thermal; without supply } - // The BT840XE runs everything: the firmware and the Zigbee link. It reflows on the last pass: Fanstel - // allows no opposite-side reflow. The ferrite and bulk capacitor follow Fanstel's design note for a - // noisy supply, since the rail comes from a switcher. - place bt840xe "U_MCU1" designator="U_MCU1" footprint="SnipsControllers_Custom:BT840XE" value="BT840XE" - place inductor "FB_RF1" designator="FB_RF1" footprint="Inductor_SMD:L_0603_1608Metric" value="600Ω@100MHz" - place capacitor "C_RF_BULK1" designator="C_RF_BULK1" footprint="Capacitor_SMD:C_1206_3216Metric" value="47µF" - // Tag-Connect pads and locating holes for SWD: a new module holds Fanstel's AT firmware, so a blank board is - // first programmed here. They are bare copper; hand=#true marks them DNP, since the BOM requires an MPN on every placement. - place tc2030-nl "J_SWD1" designator="J_SWD1" footprint="Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical" value="TC2030-NL" manufacturer="None" mpn="Copper pad, no part" hand=#true + // Reflows on the last pass, on top: Espressif requires a single reflow for the module. The MINI-1U fits the + // 17.5 mm between the macro row and the USB pads, where the 19.2 mm WROOM-1U does not. + // Turned 270 degrees so the signal pins face the stick, the OLED and the carrier, and the GND edge faces the side. + // Pins are assigned by position, not from V1's map. RXD0 keeps PWR_HOLD: its reset pull-up (ESP32-S3 datasheet + // Table 2-1) holds the latch through a reset, so a watchdog reset reboots the board instead of turning it off. + place esp32-s3-mini-1u "U_MCU1" designator="U_MCU1" footprint="Espressif:ESP32-S3-MINI-1U" value="ESP32-S3-MINI-1U-N8" + // Optional XBee 3 daughter board, hand-soldered to these pads by its castellations. It carries the XBee's + // decoupling, the RESET pull-up and RC, and the ATTN/BOOTMODE pull-up, so nothing here depends on it being fitted. + place xbee-carrier "U_XBEE1" designator="U_XBEE1" footprint="SnipsControllers_Custom:XBee_Carrier_Castellated" value="XBee carrier" manufacturer="Snips Controllers" mpn="Snips XBee carrier" hand=#true place resistor "R_I2C_SCL1" designator="R_I2C_SCL1" footprint="Resistor_SMD:R_0402_1005Metric" value="4.7kΩ" place resistor "R_I2C_SDA1" designator="R_I2C_SDA1" footprint="Resistor_SMD:R_0402_1005Metric" value="4.7kΩ" - // Low-pass for the trigger, near the ADC pin. The DRV5055 must not see a capacitor on OUT without a resistor. + // Low-pass for the trigger, with C_TRIG1 at the ADC pin. The DRV5055 must not see a capacitor on OUT without a resistor. place resistor "R_TRIG1" designator="R_TRIG1" footprint="Resistor_SMD:R_0402_1005Metric" value="1kΩ" place capacitor "C_TRIG1" designator="C_TRIG1" footprint="Capacitor_SMD:C_0402_1005Metric" value="100nF" - // VBUS bypass at the module; C_VIN_1 is about 25 mm away. Kept small so VBUS stays near USB's 10 µF limit. - place capacitor "C_VBUS1" designator="C_VBUS1" footprint="Capacitor_SMD:C_0603_1608Metric" value="1µF" place drv5055a2-sot23 "U_HALL1" designator="U_HALL1" footprint="Package_TO_SOT_SMD:SOT-23" value="DRV5055A2QDBZR" place icm42670p "U_IMU1" designator="U_IMU1" footprint="Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y" value="ICM-42670-P" place qwiic "U_OLED1" designator="U_OLED1" footprint="Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal" value="Qwiic connector" { without tab } // Electrical nets - // The hall sensor and stick are ratiometric, so they share the ADC's rail and track it through TX bursts. - circuit "FB_RF1.B" "C_RF_BULK1.A" "C_3V3_1.A" "C_3V3_2.A" "C_HALL1.A" "C_STICK1.A" "J_STICK1.p_3" "J_STICK1.p_3_" "U_HALL1.VCC" "U_MCU1.VDD" "U_MCU1.VDDH" name="/MCU_Core/3V3_RF" - set "C_RF_BULK1.A" net.voltage "3.3V" - circuit "U_MCU1.USB_DP" "J_USB1.D+" name="/MCU_Core/USB_DP" - circuit "U_MCU1.USB_DM" "J_USB1.D-" name="/MCU_Core/USB_DM" - circuit "J_SWD1.SWDIO" "U_MCU1.SWDIO" name="/MCU_Core/SWDIO" - circuit "J_SWD1.SWCLK" "U_MCU1.SWDCLK" name="/MCU_Core/SWDCLK" - circuit "J_SWD1.RESET" "SW_RST1.2" "U_MCU1.RESET" name="/MCU_Core/MCU_RESET" - circuit "R_I2C_SCL1.B" "U_IMU1.AP_SCL" "U_MCU1.P0_27" "U_OLED1.4" name="/Accelerometer/I2C_SCL" - circuit "R_I2C_SDA1.B" "U_IMU1.AP_SDA" "U_MCU1.P0_26" "U_OLED1.3" name="/Accelerometer/I2C_SDA" - circuit "SW_MACRO1.1" "U_MCU1.P1_10" name="/Buttons_Direct/BTN_MACRO1" - circuit "SW_MACRO2.1" "U_MCU1.P0_07" name="/Buttons_Direct/BTN_MACRO2" - circuit "SW_MACRO3.1" "U_MCU1.P1_09" name="/Buttons_Direct/BTN_MACRO3" - circuit "SW_MACRO4.1" "U_MCU1.P1_11" name="/Buttons_Direct/BTN_MACRO4" - circuit "SW_MACRO5.1" "U_MCU1.P1_07" name="/Buttons_Direct/BTN_MACRO5" - circuit "SW_MACRO6.1" "U_MCU1.P0_20" name="/Buttons_Direct/BTN_MACRO6" - circuit "SW_THR_DN1.1" "U_MCU1.P1_06" name="/Buttons_Direct/BTN_THR_DN" - circuit "SW_THR_UP1.1" "U_MCU1.P1_08" name="/Buttons_Direct/BTN_THR_UP" - circuit "SW_TRIG_DIG1.1" "U_MCU1.P1_04" name="/Buttons_Direct/BTN_TRIG_DIG" - circuit "SW_VOL_DN1.1" "U_MCU1.P0_12" name="/Buttons_Direct/BTN_VOL_DN" - circuit "SW_VOL_UP1.1" "U_MCU1.P1_05" name="/Buttons_Direct/BTN_VOL_UP" + circuit "U_MCU1.USB_D-" "R_USB_DM1.B" name="/MCU_Core/USB_DM_MCU" + circuit "R_USB_DM1.A" "J_USB1.D-" name="/MCU_Core/USB_DM" + circuit "U_MCU1.USB_D+" "R_USB_DP1.B" name="/MCU_Core/USB_DP_MCU" + circuit "R_USB_DP1.A" "J_USB1.D+" name="/MCU_Core/USB_DP" + circuit "C_EN1.A" "R_EN_PU1.A" "U_MCU1.EN" name="/MCU_Core/MCU_EN" + circuit "R_I2C_SCL1.B" "U_IMU1.AP_SCL" "U_MCU1.IO13" "U_OLED1.4" name="/Accelerometer/I2C_SCL" + circuit "R_I2C_SDA1.B" "U_IMU1.AP_SDA" "U_MCU1.IO12" "U_OLED1.3" name="/Accelerometer/I2C_SDA" + circuit "SW_MACRO1.1" "U_MCU1.IO16" name="/Buttons_Direct/BTN_MACRO1" + circuit "SW_MACRO2.1" "U_MCU1.IO5" name="/Buttons_Direct/BTN_MACRO2" + circuit "SW_MACRO3.1" "U_MCU1.IO4" name="/Buttons_Direct/BTN_MACRO3" + circuit "SW_MACRO4.1" "U_MCU1.IO11" name="/Buttons_Direct/BTN_MACRO4" + circuit "SW_MACRO5.1" "U_MCU1.IO8" name="/Buttons_Direct/BTN_MACRO5" + circuit "SW_MACRO6.1" "U_MCU1.IO2" name="/Buttons_Direct/BTN_MACRO6" + circuit "SW_THR_DN1.1" "U_MCU1.IO18" name="/Buttons_Direct/BTN_THR_DN" + circuit "SW_THR_UP1.1" "U_MCU1.IO33" name="/Buttons_Direct/BTN_THR_UP" + circuit "SW_TRIG_DIG1.1" "U_MCU1.IO47" name="/Buttons_Direct/BTN_TRIG_DIG" + circuit "SW_VOL_DN1.1" "U_MCU1.IO40" name="/Buttons_Direct/BTN_VOL_DN" + circuit "SW_VOL_UP1.1" "U_MCU1.IO38" name="/Buttons_Direct/BTN_VOL_UP" circuit "R_TRIG1.A" "U_HALL1.OUT" name="/Hall_Trigger/TRIG_ANALOG" - circuit "C_TRIG1.A" "R_TRIG1.B" "U_MCU1.P0_04" name="/Hall_Trigger/TRIG_ADC" - circuit "J_STICK1.p_a" "U_MCU1.P1_03" name="/MCU_Core/BTN_STICK" - circuit "R_BOOT_PU1.A" "SW_BOOT1.2" "U_MCU1.P1_00" name="/MCU_Core/MCU_BOOT" - circuit "C_DBNC1.A" "D_INV_ISO1.K" "R_BTN_PU1.B" "SW_PWR1.1" "U_MCU1.P0_11" name="/MCU_Core/PWR_BTN_SENSE" - circuit "D_OR2.A" "U_MCU1.P1_13" name="/MCU_Core/PWR_HOLD" - circuit "R_RGB1.B" "U_MCU1.P0_13" name="/MCU_Core/RGB_DIN" - circuit "R_STAT1.A" "U_CHG1.STAT1" "U_MCU1.P1_14" name="/MCU_Core/STAT1" - circuit "R_STAT2.A" "U_CHG1.STAT2" "U_MCU1.P1_15" name="/MCU_Core/STAT2" - circuit "J_STICK1.p_2" "U_MCU1.P0_02" name="/MCU_Core/STICK_X" - circuit "J_STICK1.p_2_" "U_MCU1.P0_03" name="/MCU_Core/STICK_Y" - circuit "R_VSYS1.B" "R_VSYS2.A" "U_MCU1.P0_05" name="/MCU_Core/VSYS_SENSE" + circuit "C_TRIG1.A" "R_TRIG1.B" "U_MCU1.IO9" name="/Hall_Trigger/TRIG_ADC" + circuit "J_STICK1.p_a" "U_MCU1.IO17" name="/MCU_Core/BTN_STICK" + circuit "R_BOOT_PU1.A" "SW_BOOT1.2" "U_MCU1.IO0" name="/MCU_Core/MCU_BOOT" + circuit "C_DBNC1.A" "D_INV_ISO1.K" "R_BTN_PU1.B" "SW_PWR1.1" "U_MCU1.IO21" name="/MCU_Core/PWR_BTN_SENSE" + circuit "D_OR2.A" "U_MCU1.RXD0" name="/MCU_Core/PWR_HOLD" + circuit "R_RGB1.B" "U_MCU1.IO48" name="/MCU_Core/RGB_DIN" + circuit "R_STAT1.A" "U_CHG1.STAT1" "U_MCU1.IO15" name="/MCU_Core/STAT1" + circuit "R_STAT2.A" "U_CHG1.STAT2" "U_MCU1.IO14" name="/MCU_Core/STAT2" + circuit "J_STICK1.p_2" "U_MCU1.IO7" name="/MCU_Core/STICK_X" + circuit "J_STICK1.p_2_" "U_MCU1.IO6" name="/MCU_Core/STICK_Y" + circuit "R_VSYS1.B" "R_VSYS2.A" "U_MCU1.IO10" name="/MCU_Core/VSYS_SENSE" + // XBee UART in API mode, with flow control. RTS and DTR also allow serial firmware recovery through the ESP32. + circuit "U_MCU1.IO34" "U_XBEE1.CTS" name="/XBee/XBEE_CTS" + circuit "U_MCU1.IO35" "U_XBEE1.DIN" name="/XBee/XBEE_DIN" + circuit "U_MCU1.IO36" "U_XBEE1.DOUT" name="/XBee/XBEE_DOUT" + circuit "U_MCU1.IO39" "U_XBEE1.RTS" name="/XBee/XBEE_RTS" + circuit "U_MCU1.IO41" "U_XBEE1.ON_SLEEP" name="/XBee/XBEE_ON_SLEEP" + circuit "U_MCU1.IO42" "U_XBEE1.RESET" name="/XBee/XBEE_RESET" + circuit "U_MCU1.IO1" "U_XBEE1.SLEEP_RQ" name="/XBee/XBEE_SLEEP_RQ" circuit "R_FB1.A" "R_FB2.A" "U_BUCK1.FB" name="/Power_Buck/BUCK_FB" circuit "L_BUCK1.A" "U_BUCK1.SW" name="/Power_Buck/BUCK_SW" circuit "Q_PWR1.DRAIN" "R_PWR_EN_PD1.node" "U_BUCK1.EN" name="/Power_Buck/PWR_EN" @@ -153,42 +159,23 @@ design snips_controller { circuit "D_RGB1.DIN" "R_RGB1.A" name="/RGB_LED/RGB_DIN_R" circuit "J_USB1.CC1" "R_CC1.A" name="/USB_C/USB_CC1" circuit "J_USB1.CC2" "R_CC2.A" name="/USB_C/USB_CC2" - circuit "FB_RF1.A" "J_SWD1.VCC" "C_BUCK_OUT1.A" "C_IMU_1.A" "C_IMU_2.A" "C_IMU_3.A" "C_OLED_1.A" "C_OLED_2.A" "C_RGB1.A" "D_RGB1.VDD" "L_BUCK1.B" "R_BOOT_PU1.B" "R_BTN_PU1.A" "R_FB1.B" "R_STAT1.B" "R_STAT2.B" "U_IMU1.AP_CS" "U_IMU1.VDD" "U_IMU1.VDDIO" "R_I2C_SCL1.A" "R_I2C_SDA1.A" "U_OLED1.2" name="3V3" + circuit "C_3V3_1.A" "C_3V3_2.A" "C_3V3_3.A" "C_HALL1.A" "C_STICK1.A" "J_STICK1.p_3" "J_STICK1.p_3_" "R_EN_PU1.B" "U_HALL1.VCC" "U_MCU1.3V3" "U_XBEE1.VCC" "C_BUCK_OUT1.A" "C_IMU_1.A" "C_IMU_2.A" "C_IMU_3.A" "C_OLED_1.A" "C_OLED_2.A" "C_RGB1.A" "D_RGB1.VDD" "L_BUCK1.B" "R_BOOT_PU1.B" "R_BTN_PU1.A" "R_FB1.B" "R_STAT1.B" "R_STAT2.B" "U_IMU1.AP_CS" "U_IMU1.VDD" "U_IMU1.VDDIO" "R_I2C_SCL1.A" "R_I2C_SDA1.A" "U_OLED1.2" name="3V3" set "C_BUCK_OUT1.A" net.voltage "3.3V" - circuit "U_IMU1.INT1" "U_MCU1.P1_12" name="ACCEL_INT1" - circuit "BT1.2" "C_3V3_1.B" "C_3V3_2.B" "C_RF_BULK1.B" "J_SWD1.GND" "C_BAT1.B" "C_BUCK_IN1.B" "C_BUCK_OUT1.B" "C_DBNC1.B" "C_HALL1.B" "C_IMU_1.B" "C_IMU_2.B" "C_IMU_3.B" "C_LATCH_G1.A" "C_OLED_1.B" "C_OLED_2.B" "C_RGB1.B" "C_STICK1.B" "C_SYS_1.B" "C_TRIG1.B" "C_VBUS1.B" "C_SYS_2.B" "C_VIN_1.B" "C_VIN_2.B" "D_RGB1.GND" "D_VBUS_TVS1.A2" "J_STICK1.p_1" "J_STICK1.p_1_" "J_STICK1.p_c" "J_USB1.GND" "J_USB1.SHIELD" "Q_INV1.EMITTER" "Q_LATCH1.SOURCE" "R_CC1.B" "R_CC2.B" "R_FB2.B" "R_ISET1.B" "R_LATCH_G1.A" "R_PWR_EN_PD1.rail.gnd" "R_TS1.B" "R_VSET1.B" "R_VSYS2.B" "SW_BOOT1.1" "SW_MACRO1.2" "SW_MACRO2.2" "SW_MACRO3.2" "SW_MACRO4.2" "SW_MACRO5.2" "SW_MACRO6.2" "SW_PWR1.2" "SW_RST1.1" "SW_THR_DN1.2" "SW_THR_UP1.2" "SW_TRIG_DIG1.2" "SW_VOL_DN1.2" "SW_VOL_UP1.2" "U_BUCK1.GND" "U_CHG1.PAD" "U_CHG1.CE" "U_CHG1.GND" "U_HALL1.GND" "U_IMU1.AP_AD0" "U_IMU1.FSYNC" "U_IMU1.GND" "U_IMU1.RESV2" "U_IMU1.RESV3" "U_IMU1.RESV10" "U_IMU1.RESV11" "U_MCU1.GND" "U_OLED1.1" name="GND" + circuit "U_IMU1.INT1" "U_MCU1.IO37" name="ACCEL_INT1" + circuit "BT1.2" "C_3V3_1.B" "C_3V3_2.B" "C_3V3_3.B" "C_EN1.B" "C_BAT1.B" "C_BUCK_IN1.B" "C_BUCK_OUT1.B" "C_DBNC1.B" "C_HALL1.B" "C_IMU_1.B" "C_IMU_2.B" "C_IMU_3.B" "C_LATCH_G1.A" "C_OLED_1.B" "C_OLED_2.B" "C_RGB1.B" "C_STICK1.B" "C_SYS_1.B" "C_TRIG1.B" "C_SYS_2.B" "C_VIN_1.B" "C_VIN_2.B" "D_RGB1.GND" "D_VBUS_TVS1.A2" "J_STICK1.p_1" "J_STICK1.p_1_" "J_STICK1.p_c" "J_USB1.GND" "J_USB1.SHIELD" "Q_INV1.EMITTER" "Q_LATCH1.SOURCE" "R_CC1.B" "R_CC2.B" "R_FB2.B" "R_ISET1.B" "R_LATCH_G1.A" "R_PWR_EN_PD1.rail.gnd" "R_TS1.B" "R_VSET1.B" "R_VSYS2.B" "SW_BOOT1.1" "SW_MACRO1.2" "SW_MACRO2.2" "SW_MACRO3.2" "SW_MACRO4.2" "SW_MACRO5.2" "SW_MACRO6.2" "SW_PWR1.2" "SW_THR_DN1.2" "SW_THR_UP1.2" "SW_TRIG_DIG1.2" "SW_VOL_DN1.2" "SW_VOL_UP1.2" "U_BUCK1.GND" "U_CHG1.PAD" "U_CHG1.CE" "U_CHG1.GND" "U_HALL1.GND" "U_IMU1.AP_AD0" "U_IMU1.FSYNC" "U_IMU1.GND" "U_IMU1.RESV2" "U_IMU1.RESV3" "U_IMU1.RESV10" "U_IMU1.RESV11" "U_MCU1.GND" "U_XBEE1.GND" "U_OLED1.1" name="GND" circuit "BT1.1" "C_BAT1.A" "U_CHG1.BAT" name="VBAT" - circuit "C_VBUS1.A" "C_VIN_1.A" "C_VIN_2.A" "D_VBUS_TVS1.A1" "J_USB1.VBUS" "U_CHG1.IN" "U_MCU1.VBUS" name="VBUS" + circuit "C_VIN_1.A" "C_VIN_2.A" "D_VBUS_TVS1.A1" "J_USB1.VBUS" "U_CHG1.IN" name="VBUS" circuit "C_BUCK_IN1.A" "C_SYS_1.A" "C_SYS_2.A" "Q_PWR1.SOURCE" "R_GATE1.A" "R_INV_BASE1.A" "R_INV_PU1.A" "R_VSYS1.A" "U_BUCK1.VIN" "U_CHG1.SYS" name="VSYS" nc "D_INV_ISO1.NC" nc "D_RGB1.DOUT" - nc "J_SWD1.SWO" // P1.00 is the boot button, so SWO is not used nc "J_USB1.SBU1" nc "J_USB1.SBU2" nc "U_IMU1.INT2" - nc "U_MCU1.P0_00" - nc "U_MCU1.P0_01" - nc "U_MCU1.P0_21" - nc "U_MCU1.P0_09" - nc "U_MCU1.P0_10" - nc "U_MCU1.P0_28" - nc "U_MCU1.P0_29" - nc "U_MCU1.P0_25" - nc "U_MCU1.P0_30" - nc "U_MCU1.P0_31" - nc "U_MCU1.P0_06" - nc "U_MCU1.P0_08" - nc "U_MCU1.P0_24" - nc "U_MCU1.P0_22" - nc "U_MCU1.P0_17" - nc "U_MCU1.P0_15" - nc "U_MCU1.P1_02" - nc "U_MCU1.P0_23" - nc "U_MCU1.P0_19" - nc "U_MCU1.P0_16" - nc "U_MCU1.P0_14" - nc "U_MCU1.P1_01" - nc "U_MCU1.DCCH" + nc "U_MCU1.IO3" // strap: floating is fine, and a load could upset the JTAG source select + nc "U_MCU1.IO45" // strap: stays on its internal pull-down, since high would select 1.8 V flash + nc "U_MCU1.IO46" // strap: stays on its internal pull-down, so no load can disturb the boot mode + nc "U_MCU1.TXD0" // prints the boot log, so it stays free for debugging + nc "U_MCU1.IO26" // SPICS1: Arduino's PSRAM probe drives it at every boot, so nothing may hang off it // Select the pre-port components by resolved value and footprint. // This also applies to future support parts with the same specification. @@ -213,19 +200,9 @@ design snips_controller { set mpn="0402WGF1000TCE" } match placement { - when value="BT840XE" - when footprint="SnipsControllers_Custom:BT840XE" - set mpn="BT840XE" - } - match placement { - when value="600Ω@100MHz" - when footprint="Inductor_SMD:L_0603_1608Metric" - set mpn="BLM18KG601SN1D" - } - match placement { - when value="47µF" - when footprint="Capacitor_SMD:C_1206_3216Metric" - set mpn="CL31A476MPHNNNE" + when value="ESP32-S3-MINI-1U-N8" + when footprint="Espressif:ESP32-S3-MINI-1U" + set mpn="ESP32-S3-MINI-1U-N8" } match placement { when value="4.7kΩ" diff --git a/PCB/v2.x/stackup/parts.kdl b/PCB/v2.x/stackup/parts.kdl index 04a3cfa..6e2ec58 100644 --- a/PCB/v2.x/stackup/parts.kdl +++ b/PCB/v2.x/stackup/parts.kdl @@ -293,176 +293,197 @@ part skrp-button { } } +// Espressif ESP32-S3-MINI-1U-N8: 15.4 x 15.4 x 2.4 mm, 8 MB flash, no PSRAM, external antenna connector. The +// @stackup/micro/esp32s3 library part is the WROOM-1 only. Pin data is from the MINI-1 and MINI-1U datasheet v1.7, +// Table 3-1, with straps from Table 4-1, and the footprint is Espressif's, which matches Figure 11-2. On the N8, +// IO26 and IO33-37 are free GPIOs; the N4R2 takes IO26 for PSRAM, so do not substitute it. +part esp32-s3-mini-1u { + symbol "Espressif:ESP32-S3-MINI-1" + reference U + value "ESP32-S3-MINI-1U-N8" + datasheet "https://documentation.espressif.com/esp32-s3-mini-1_mini-1u_datasheet_en.pdf" + description "ESP32-S3 Wi-Fi + Bluetooth LE module, 8 MB flash, no PSRAM, external antenna connector, 15.4x15.4x2.4mm" + manufacturer "Espressif Systems" + order mpn=ESP32-S3-MINI-1U-N8 lcsc=C2980299 + + pin "3V3" power_in + pin GND power_in -// Tag-Connect TC2030-NL footprint: six pads and three locating holes, no part fitted. A TC2030-CTX-NL cable -// presses against it to reach SWD. Pinout is from Tag-Connect's TC2030-CTX sheet. -part tc2030-nl { - symbol "Connector_Generic:Conn_02x03_Odd_Even" - reference J - value "TC2030-NL" - description "Tag-Connect TC2030-NL SWD pads, no part fitted" - - pin VCC passive - pin SWDIO passive - pin RESET passive - pin SWCLK passive - pin GND passive - pin SWO passive - - package tc2030 footprint="Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical" { - pad VCC "1" - pad SWDIO "2" - pad RESET "3" - pad SWCLK "4" - pad GND "5" - pad SWO "6" + // The external supply must deliver at least 0.5 A (Table 6-2), which covers radio transmit bursts. + port v3v3 type=power { + require net.voltage min="3.0V" max="3.6V" + add net.draw "500mA" + line rail pin="3V3" + line gnd pin=GND } -} + pin EN input required { + role reset active=low pull=none + require net.rest not=low + } + pin IO0 bidirectional once { + role strap sampled=reset pull=internal-up \ + note="boot mode: high is SPI boot, low is download; a GPIO afterwards" + require net.rest high + } + pin IO3 bidirectional once { + role strap sampled=reset pull=none \ + note="JTAG source: low selects external pins, high selects USB Serial/JTAG" + } + pin IO45 bidirectional once { + role strap sampled=reset pull=internal-down \ + note="VDD_SPI: must stay low, since high selects 1.8 V and this flash is 3.3 V" + require net.rest not=high + } + pin IO46 bidirectional once { + role strap sampled=reset pull=internal-down \ + note="ROM message control: high with IO0 low is an invalid boot combination" + require net.rest not=high + } + pin IO1 bidirectional once + pin IO2 bidirectional once + pin IO4 bidirectional once + pin IO5 bidirectional once + pin IO6 bidirectional once + pin IO7 bidirectional once + pin IO8 bidirectional once + pin IO9 bidirectional once + pin IO10 bidirectional once + pin IO11 bidirectional once + pin IO12 bidirectional once + pin IO13 bidirectional once + pin IO14 bidirectional once + pin IO15 bidirectional once + pin IO16 bidirectional once + pin IO17 bidirectional once + pin IO18 bidirectional once + pin "USB_D-" bidirectional once + pin "USB_D+" bidirectional once + pin IO21 bidirectional once + pin IO26 bidirectional once + pin IO47 bidirectional once + pin IO33 bidirectional once + pin IO34 bidirectional once + pin IO48 bidirectional once + pin IO35 bidirectional once + pin IO36 bidirectional once + pin IO37 bidirectional once + pin IO38 bidirectional once + pin IO39 bidirectional once + pin IO40 bidirectional once + pin IO41 bidirectional once + pin IO42 bidirectional once + pin TXD0 bidirectional once + pin RXD0 bidirectional once + + package module footprint="Espressif:ESP32-S3-MINI-1U" { + pad GND 1 + pad GND 2 + pad "3V3" 3 + pad IO0 4 + pad IO1 5 + pad IO2 6 + pad IO3 7 + pad IO4 8 + pad IO5 9 + pad IO6 10 + pad IO7 11 + pad IO8 12 + pad IO9 13 + pad IO10 14 + pad IO11 15 + pad IO12 16 + pad IO13 17 + pad IO14 18 + pad IO15 19 + pad IO16 20 + pad IO17 21 + pad IO18 22 + pad "USB_D-" 23 + pad "USB_D+" 24 + pad IO21 25 + pad IO26 26 + pad IO47 27 + pad IO33 28 + pad IO34 29 + pad IO48 30 + pad IO35 31 + pad IO36 32 + pad IO37 33 + pad IO38 34 + pad IO39 35 + pad IO40 36 + pad IO41 37 + pad IO42 38 + pad TXD0 39 + pad RXD0 40 + pad IO45 41 + pad GND 42 + pad GND 43 + pad IO46 44 + pad EN 45 + pad GND 46 + pad GND 47 + pad GND 48 + pad GND 49 + pad GND 50 + pad GND 51 + pad GND 52 + pad GND 53 + pad GND 54 + pad GND 55 + pad GND 56 + pad GND 57 + pad GND 58 + pad GND 59 + pad GND 60 + pad GND 61 + pad GND 62 + pad GND 63 + pad GND 64 + pad GND 65 + } +} -// Fanstel BT840XE: nRF52840-QIAA, SKY66112 PA, 32.768 kHz crystal, u.FL. Runs the whole controller and -// the Zigbee link. Pin data is from Fanstel's Product Specifications Ver 1.26. P0.06, P0.08, P0.17 and -// P0.19 drive the PA and are not connected at the pads. P0.00 and P0.01 go to the module's crystal. -// VDD must be regulated 3.3 V, 300 mA minimum; VDDH alone cannot power the PA (Note 1). -part bt840xe { - symbol "SnipsControllers_Custom:BT840XE" +// Pads for the optional XBee 3 carrier, a separate 2-layer daughter board that sits flat on the underside and is +// hand-soldered by its castellations. Pads run 1.7 mm past the board's 22 x 17 mm outline for the iron. The carrier +// holds the XBee's decoupling, the RESET pull-up and RC, and the ATTN/BOOTMODE pull-up. VCC draw is the XBee 3 PRO's +// 140 mA at +19 dBm (Digi 90001543). DIN is the XBee's input and DOUT its output, so the ESP32 transmits on DIN. +part xbee-carrier { + symbol "Connector_Generic:Conn_02x06_Odd_Even" reference U - value "BT840XE" - datasheet "https://www.fanstel.com/s/BT840X-p-Product-Specifications-cjd4.pdf" - description "nRF52840 Zigbee/Thread/BLE module, +21 dBm PA, u.FL, 15x28x1.9mm" - manufacturer "Fanstel" - order mpn=BT840XE lcsc=C6132678 - - pin P0_26 bidirectional - pin P0_27 bidirectional - pin P0_00 bidirectional - pin P0_01 bidirectional - pin P0_02 bidirectional - pin P0_03 bidirectional - pin P0_09 bidirectional - pin P0_10 bidirectional - pin VDD power_in + value "XBee carrier" + description "Solder pads for the Snips XBee 3 castellated daughter board, 22x17mm" + pin GND power_in - pin P0_11 bidirectional - pin P1_00 bidirectional - pin P0_13 bidirectional + pin VCC power_in + pin DIN input + pin DOUT output + pin RTS input + pin CTS output + pin SLEEP_RQ input + pin ON_SLEEP output pin RESET input - pin SWDCLK input - pin SWDIO bidirectional - pin P1_11 bidirectional - pin P1_12 bidirectional - pin P1_13 bidirectional - pin P1_14 bidirectional - pin P1_15 bidirectional - pin P1_10 bidirectional - pin P1_06 bidirectional - pin P0_28 bidirectional - pin P0_29 bidirectional - pin P0_04 bidirectional - pin P0_05 bidirectional - pin P0_07 bidirectional - pin P1_08 bidirectional - pin P0_25 bidirectional - pin P0_30 bidirectional - pin P0_31 bidirectional - pin P0_06 bidirectional - pin P0_08 bidirectional - pin P1_03 bidirectional - pin P0_24 bidirectional - pin P0_22 bidirectional - pin P0_17 bidirectional - pin P0_15 bidirectional - pin P1_02 bidirectional - pin P1_04 bidirectional - pin P0_23 bidirectional - pin P0_19 bidirectional - pin P0_16 bidirectional - pin P0_14 bidirectional - pin P1_01 bidirectional - pin P1_05 bidirectional - pin P1_07 bidirectional - pin P0_20 bidirectional - pin P0_21 bidirectional - pin P1_09 bidirectional - pin USB_DP bidirectional - pin USB_DM bidirectional - pin P0_12 bidirectional - pin VDDH power_in - pin DCCH passive - pin VBUS power_in - - package module footprint="SnipsControllers_Custom:BT840XE" { - pad P0_26 "1" - pad P0_27 "2" - pad P0_00 "3" - pad P0_01 "4" - pad P0_02 "5" - pad P0_03 "6" - pad P0_09 "7" - pad P0_10 "8" - pad VDD "9" - pad GND "10" - pad P0_11 "11" - pad P1_00 "12" - pad P0_13 "13" - pad RESET "14" - pad SWDCLK "15" - pad SWDIO "16" - pad P1_11 "Z0" - pad P1_12 "Z1" - pad P1_13 "Z2" - pad P1_14 "Z3" - pad P1_15 "Z4" - pad P1_10 "Z5" - pad P1_06 "Z6" - pad GND "A0" - pad P0_28 "A1" - pad P0_29 "A2" - pad P0_04 "A3" - pad P0_05 "A4" - pad P0_07 "A5" - pad P1_08 "A6" - pad GND "B0" - pad P0_25 "B1" - pad P0_30 "B2" - pad P0_31 "B3" - pad P0_06 "B4" - pad P0_08 "B5" - pad P1_03 "B6" - pad GND "C0" - pad P0_24 "C1" - pad P0_22 "C2" - pad P0_17 "C3" - pad P0_15 "C4" - pad P1_02 "C5" - pad P1_04 "C6" - pad GND "D0" - pad P0_23 "D1" - pad P0_19 "D2" - pad P0_16 "D3" - pad P0_14 "D4" - pad P1_01 "D5" - pad P1_05 "D6" - pad P1_07 "E0" - pad P0_20 "E1" - pad P0_21 "E2" - pad P1_09 "E3" - pad USB_DP "E4" - pad USB_DM "E5" - pad P0_12 "E6" - pad GND "F0" - pad GND "F1" - pad GND "F2" - pad GND "F3" - pad VDDH "F4" - pad DCCH "F5" - pad VBUS "F6" + + package castellated footprint="SnipsControllers_Custom:XBee_Carrier_Castellated" { + pad CTS 1 + pad DIN 2 + pad DOUT 3 + pad RTS 4 + pad ON_SLEEP 5 + pad RESET 6 + pad SLEEP_RQ 7 + pad GND 8 + pad VCC 9 + pad VCC 10 + pad GND 11 + pad GND 12 } - port vdd type=power { - require net.voltage min="1.7V" max="3.6V" - add net.draw "300mA" - line rail pin=VDD + port vcc type=power { + require net.voltage min="2.1V" max="3.6V" + add net.draw "140mA" + line rail pin=VCC line gnd pin=GND } } diff --git a/PCB/v2.x/stackup/purchasing.kdl b/PCB/v2.x/stackup/purchasing.kdl index 40ce9a5..c9612d7 100644 --- a/PCB/v2.x/stackup/purchasing.kdl +++ b/PCB/v2.x/stackup/purchasing.kdl @@ -165,14 +165,6 @@ mpn "TYPE-C-31-M-12" manufacturer="Hroparts Elec" value="USB-C" footprint="Conne catalog lcsc="C165948" } -mpn "BT840XE" manufacturer="Fanstel" value="BT840XE" footprint="SnipsControllers_Custom:BT840XE" { - catalog lcsc="C6132678" -} - -mpn "BLM18KG601SN1D" manufacturer="Murata" value="600Ω@100MHz" footprint="Inductor_SMD:L_0603_1608Metric" { - catalog lcsc="C85833" -} - -mpn "CL31A476MPHNNNE" manufacturer="Samsung Electro-Mechanics" value="47µF" footprint="Capacitor_SMD:C_1206_3216Metric" { - catalog lcsc="C96123" +mpn "ESP32-S3-MINI-1U-N8" manufacturer="Espressif Systems" value="ESP32-S3-MINI-1U-N8" footprint="Espressif:ESP32-S3-MINI-1U" { + catalog lcsc="C2980299" } diff --git a/PCB/v2.x/sym-lib-table b/PCB/v2.x/sym-lib-table index 725bd69..4b48dd3 100644 --- a/PCB/v2.x/sym-lib-table +++ b/PCB/v2.x/sym-lib-table @@ -3,4 +3,5 @@ (lib (name "SnipsControllers") (type "KiCad") (uri "${KIPRJMOD}/libraries/SnipsControllers.kicad_sym") (options "") (descr "")) (lib (name "BQ25185DLHR") (type "KiCad") (uri "${KIPRJMOD}/libraries/BQ25185DLHR/BQ25185DLHR.kicad_sym") (options "") (descr "")) (lib (name "SnipsControllers_Custom") (type "KiCad") (uri "${KIPRJMOD}/libraries/SnipsControllers_Custom.kicad_sym") (options "") (descr "")) + (lib (name "Espressif") (type "KiCad") (uri "${KIPRJMOD}/libraries/Espressif.kicad_sym") (options "") (descr "")) )